Human reliability analysis for In-Tank Precipitation alignment and startup of emergency purge ventilation equipment

International Nuclear Information System (INIS)

Olsen, L.M.

1993-08-01

This report documents the methodology used for calculating the human error probability for establishing air based ventilation using emergency purge ventilation equipment on In-Tank Precipitation (ITP) processing tanks 48 and 49 after a failure of the nitrogen purge system following a seismic event. The analyses were performed according to THERP (Technique for Human Error Rate Prediction). The calculated human error probabilities are provided as input to the Fault Tree Analysis for the ITP Nitrogen Purge System. The analysis assumes a seismic event initiator leading to establishing air based ventilation on the ITP processing tanks 48 and 49. At the time of this analysis only the tanks and the emergency purge ventilation equipment are seismically qualified. Consequently, onsite and offsite power is assumed to be unavailable and all operator control actions are to be performed locally on the tank top. Assumptions regarding procedures, staffing, equipment locations, equipment tagging, equipment availability, and training were made and are documented in this report. The human error probability for establishing air based ventilation using the emergency purge ventilation equipment on In-Tank Precipitation processing tanks 48 and 49 after a failure of the nitrogen purge system following a seismic event is 4.2E-6 (median value on the lognormal scale). It is important to note that this result is predicated on the implementation of all of the assumptions listed in the ''Assumptions'' section of this report. This analysis was not based on the current conditions in ITP. The analysis is to be used as a tool to aid ITP operations personnel in achieving the training, procedural, and operational goals outlined in this document

40 CFR 80.170 - Volumetric additive reconciliation (VAR), equipment calibration, and recordkeeping requirements.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Volumetric additive reconciliation... ADDITIVES Detergent Gasoline § 80.170 Volumetric additive reconciliation (VAR), equipment calibration, and...) For a facility which uses a gauge to measure the inventory of the detergent storage tank, the total...

Emergency response exercise of laboratories equipped with gamma spectrometry

International Nuclear Information System (INIS)

Mala, H.; Jezkova, T.; Rulik, P.; Beckova, V. et al.

2014-01-01

Seven laboratories equipped with semiconductor gamma spectrometry (HPGe detectors) are currently included in the Radiation Monitoring Network (RMN) in the Czech Republic. These laboratories have more than 30 spectrometric chains and approximately 20 'experts' and 70 'users' who would guarantee measurements during the radiological emergency (RE). The emergency exercise was carried out in 5 of them in 2014 (in 4 of them also in 2013). The aim was to test repeatedly their capacity in existing technical facilities and with current staff in the event of a RE and identify problems (bottlenecks) in the whole process from receipt of samples to entering the results into the central database of RMN. Duration of the exercise was 12 hours, due to the shortage of staff; work in one 12-hour shift is presumed during a RE, which the laboratories should be able to provide for 14 days. These exercise samples covered a wide range of commodities that would probably come to the laboratories during the RE (aerosol filters, sorbents for sorption of gaseous forms of iodine, fallout, surface and drinking waters, food chain components and soils). Some of the samples were previously spiked with 85 Sr, 88 Y and 40 K (in the exercise these nuclides represented actual contamination that would occur in RE); liquid samples were spiked with 85 Sr and 88 Y and bulk materials with 40 K.During the exercise almost 800 samples were analysed; in addition, the automatic gamma counter (GA) in Prague laboratory measured other 90 samples automatically during the night (samples were prepared during the day-shift). On the basis of the results the total measuring capacity of the laboratories of RMN CR was estimated at about 1300 samples per day. (authors)

Additional Equipment for Soil Biodegradation

Science.gov (United States)

Vondráčková, Terezie; Kraus, Michal; Šál, Jiří

2017-12-01

Intensification of industrial production, increasing citizens’ living standards, expanding the consumer assortment mean in the production - consumption cycle a constantly increasing occurrence of waste material, which by its very nature must be considered as a source of useful raw materials in all branches of human activity. In addition to strict legislative requirements, a number of circumstances characterize waste management. It is mainly extensive transport associated with the handling and storage of large volumes of substances with a large assortment of materials (substances of all possible physical and chemical properties) and high demands on reliability and time coordination of follow-up processes. Considerable differences in transport distances, a large number of sources, processors and customers, and not least seasonal fluctuations in waste and strong price pressures cannot be overlooked. This highlights the importance of logistics in waste management. Soils that are contaminated with oil and petroleum products are hazardous industrial waste. Methods of industrial waste disposal are landfilling, biological processes, thermal processes and physical and chemical methods. The paper focuses on the possibilities of degradation of oil pollution, in particular biodegradation by bacteria, which is relatively low-cost among technologies. It is necessary to win the fight with time so that no ground water is contaminated. We have developed two additional devices to help reduce oil accident of smaller ranges. In the case of such an oil accident, it is necessary to carry out the permeability test of contaminated soil in time and, on this basis, to choose the technology appropriate to the accident - either in-sit biodegradation - at the site of the accident, or on-sit - to remove the soil and biodegrade it on the designated deposits. A special injection drill was developed for in-sit biodegradation, tossing and aeration equipment of the extracted soil was developed for

Report From BPTCS Project Team On Evaluation Of Additive Manufacturing For Pressure Retaining Equipment

Energy Technology Data Exchange (ETDEWEB)

Rawls, G. [Savannah River Site (SRS), Aiken, SC (United States)

2016-09-22

ASME is evaluating the use of additive manufacturing (AM) for the construction of pressure equipment. The information in this report assesses available AM technologies for direct metal fabrication of pressure equipment. Background information is included in the report to provide context for those not experienced in AM technology. Only commercially available technologies for direct metal fabrication are addressed in the report because these AM methods are the only viable approaches for the construction of pressure equipment. Metal AM technologies can produce near-net shape parts by using multiple layers of material from a three dimensional (3D) design model of the geometry. Additive manufacturing of metal components was developed from polymer based rapid prototyping or 3D printing. At the current maturity level, AM application for pressure equipment has the potential to reduce delivery times and costs for complex shapes. AM will also lead to a reduction in the use of high cost materials, since parts can be created with corrosion resistant layers of high alloy material and structural layers of lower cost materials.

Aspects of safety assessments for package with additional equipment components

International Nuclear Information System (INIS)

Reiche, I.; Boerst, F.M.; Krietsch, T.

2004-01-01

Many paragraphs in TS-R-1 contain the terms ''package'' or ''packaging''. These terms are defined in TS-R-1 paras 230 and 231 and explained in TS-G-1.1 paras 230.1 - 230.6. The importance of a consistent understanding of these definitions has been shown by recent discussions during the assessment of applications for package design approval. There was disagreement, if equipment components attached to the container body during transport, e.g. a transport frame, should be considered part of the package and taken into account in the safety assessment for the package. Discussions were also caused by the way inner design components are treated in the safety assessment of the package. This paper summarises the regulatory requirements to such additional equipment components and presents the way of their inclusion into the package design approval process in Germany

40 CFR 80.157 - Volumetric additive reconciliation (“VAR”), equipment calibration, and recordkeeping requirements.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Volumetric additive reconciliation (â... ADDITIVES Detergent Gasoline § 80.157 Volumetric additive reconciliation (“VAR”), equipment calibration, and... other comparable VAR supporting documentation. (ii) For a facility which uses a gauge to measure the...

In-flight medical emergencies during airline operations: a survey of physicians on the incidence, nature, and available medical equipment

Directory of Open Access Journals (Sweden)

Hinkelbein J

2017-02-01

Full Text Available Jochen Hinkelbein,1,2 Christopher Neuhaus,2,3 Lennert Böhm,1 Steffen Kalina,1 Stefan Braunecker1,2 1Department of Anaesthesiology and Intensive Care Medicine, University Hospital of Cologne, Cologne, 2Working group “Emergency Medicine and Air Rescue”, German Society for Aviation and Space Medicine (DGLRM, Munich, 3Department of Anesthesiology, Heidelberg University Hospital, Heidelberg, Germany Background: Data on the incidence of in-flight medical emergencies on-board civil aircraft are uncommon and rarely published. Such data could provide information regarding required medical equipment on-board aircraft and requisite training for cabin crew. The aim of the present study was to gather data on the incidences, nature, and medical equipment for in-flight medical emergencies by way of a survey of physician members of a German aerospace medical society.Materials and methods: Using unipark.de (QuestBack GmbH, Cologne, Germany, an online survey was developed and used to gather specific information. Members of the German Society for Aviation and Space Medicine (Deutsche Gesellschaft für Luft- und Raumfahrtmedizin e.V.; DGLRM were invited to participate in the survey during a 4-week period (21 March 2015 to 20 April 2015. Chi-square test was used for statistical analysis (p<0.05 was considered significant.Results: Altogether, 121 members of the society responded to the survey (n=335 sent out. Of the 121 respondents, n=54 (44.6% of the participants (89.9% male and 10.1% female; mean age, 54.1 years; n=121 were involved in at least one in-flight medical emergency. Demographic parameters in this survey were in concordance with the society members’ demographics. The mean duration of flights was 5.7 hours and the respondents performed 7.1 airline flights per year (median. Cardiovascular (40.0% and neurological disorders (17.8% were the most frequent diagnoses. The medical equipment (78.7% provided was sufficient. An emergency diversion was

Emergency procedures

International Nuclear Information System (INIS)

Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

2004-01-01

The following subjects are discussed - Emergency Procedures: emergency equipment, emergency procedures; emergency procedure involving X-Ray equipment; emergency procedure involving radioactive sources

Emergency Victim Care. A Training Manual for Emergency Medical Technicians. Module 2. Equipment, Safe Driving Practices, Legal Aspects, Controlling the Situation, Action Evaluation Conference. Revised.

Science.gov (United States)

Ohio State Dept. of Education, Columbus. Div. of Vocational Education.

This student manual, the second in a set of 14 modules, is designed to train emergency medical technicians (EMTs) in Ohio. The module contains five sections that cover the following course content: ambulance equipment, safe driving practices for emergency vehicle drivers, legal aspects of the EMT's job, how to maintain control at an accident scene…

49 CFR 390.17 - Additional equipment and accessories.

Science.gov (United States)

2010-10-01

... equipment and accessories, not inconsistent with or prohibited by this subchapter, provided such equipment... are used. [53 FR 18052, May 19, 1988, as amended at 60 FR 38744, July 28, 1995. Redesignated at 65 FR...

An emerging etiological factor for hand injuries in the pediatric population: public exercise equipment.

Science.gov (United States)

Akşam, Berrak; Akşam, Ersin; Ceran, Candemir; Demirseren, Mustafa Erol

2016-01-01

The purpose of this study was to describe the role of public exercise equipment in pediatric hand traumas as a preventable etiological factor. Pediatric patients with hand injuries referred from the emergency department were evaluated retrospectively. Age and gender of the patients, timing, etiology, mechanism of hand trauma, localization of the injury, diagnoses of the patients, and hospitalization rates were reviewed. Amongst the 310 pediatric patients evaluated, 31 patients (10%) experienced injury related to public exercise equipment. Within this group of patients, most were between 5 to 9 years of age, and all injuries were blunt and crush type. Lacerations and fractures were the main diagnoses. Complex injuries that required inpatient care were reported in 19.3% of the patients. Public exercise equipment-related injuries are increasingly prevalent in pediatric hand traumas. Preventive actions such as shielding the moving parts should be taken to reduce these rates.

Emergency Mitigating Equipments - Post Fukushima Actions at Canadian Nuclear Power Plants - Portable AC Power Sources

International Nuclear Information System (INIS)

Vucetic, Jasmina; Kameswaran, R.

2015-01-01

In response to the Fukushima Daiichi NPP accident in 2011, the Canadian Nuclear Safety Commission set up a Task Force to evaluate operational, technical and regulatory implications on Canadian NPPs. While accepting that the risk from beyond-design-basis accidents (BDBA) at Canadian NPPs is very low, the Task Force identified a number of areas where additional improvements or confirmatory assessments would further enhance safety. As a result, a set of 36 Fukushima Action Items (FAIs) were assigned to the licensees. This paper focuses on the FAI related to electrical power system enhancements to address a total loss of all AC Power leading to a possibility of loss of heat sinks (i.e. Station Blackout). This required the licensees to implement the following: - Additional back up power supplied by portable diesel generator(s) to allow key instrumentation and control equipment and key electrical loads to remain operable; - Provisions for a storage and timely transportation and connection of the portable generator(s) to the applicable units; - Provisions for testing of the portable generator; - Provisions for fuelling of portable generators; - Provisions such as panels, receptacles, and connectors to quickly deploy the portable generators to plant system, and separate feeder cables route to avoid a common mode failure; - Load shedding strategy to extend the existing station's battery life to ensure that the connection of portable generators can be completed before the batteries are depleted; - Provisions to supply water to steam generators and Irradiated Fuel Bay using portable pumps; The paper will also provide a brief description of Electrical power systems of the Canadian NPPs designed to satisfy the high safety and reliability requirements for nuclear systems, which are based on the following: - 2 group design philosophy (Group 1 and Group 2 Electrical Power Systems) - 2 separate groups of onsite emergency generators (Class III Standby generators and Emergency

Emergency removal of football equipment: a cadaveric cervical spine injury model.

Science.gov (United States)

Gastel, J A; Palumbo, M A; Hulstyn, M J; Fadale, P D; Lucas, P

1998-10-01

To determine the influence of football helmet and shoulder pads, alone or in combination, on alignment of the unstable cervical spine. The alignment of the intact cervical spine in 8 cadavers was assessed radiographically under 4 different football equipment conditions: (1) no equipment, (2) helmet only, (3) helmet and shoulder pads, and (4) shoulder pads only. Each specimen was then surgically destabilized at C5-C6 to simulate a flexion-distraction injury. Repeat radiographs were obtained under the same 4 equipment conditions, and alignment of the unstable segment was analyzed. Before the destabilization, neutral alignment was maintained when both helmet and shoulder pads were in place. The "helmet only" condition caused a significant decrease in lordosis (mean, 9.6 +/- 4.7 degrees), whereas the "shoulder pads only" condition caused increased lordosis (13.6 +/- 6.3 degrees). After destabilization, the "helmet-only" condition demonstrated significant mean increases in C5-C6 forward angulation (16.5 +/- 8.6 degrees), posterior disc space height (3.8 +/- 2.3 mm), and dorsal element distraction (8.3 +/- 5.4 mm). Our flexion-distraction model demonstrated that immobilization of the neck-injured football player with only the helmet in place violates the principle of splinting the cervical spine in neutral alignment. By extrapolation to an extension-type injury, immobilization with only the shoulder pads left in place similarly violates this principle. In order to maintain a neutral position and minimize secondary injury to the cervical neural elements, the helmet and shoulder pads should be either both left on or both removed in the emergency setting.

Emergency preparedness in Finland: improvement of the measurement equipment used in the assessment of internal doses

Energy Technology Data Exchange (ETDEWEB)

Muikku, M.; Rahola, T. [STUK - Radiation and nuclear safety authority, Helsinki (Finland)

2006-07-01

The need for assessing internal radiation doses in emergency situations is evident. Internal exposure can be assessed using direct measurement results or by using information on activity concentrations in inhaled air and in foodstuffs combined with inhalation and consumption data. As a part of the continuous improving of emergency preparedness in Finland, S.T.U.K. - Radiation and Nuclear Safety Authority has obtained 35 monitors for thyroid measurements in field conditions and initiated a project to revise the radiation measurement equipment in local food and environmental laboratories. (authors)

Abordagem da equipe de enfermagem ao usuário na emergência em saúde mental em um pronto atendimento

Directory of Open Access Journals (Sweden)

Érika Hissae Kondo

2011-04-01

Full Text Available Pesquisa qualitativa exploratória desenvolvida em 2008, num Centro Municipal de Urgências Médicas/Curitiba. Objetivos: conhecer a concepção da equipe de enfermagem sobre emergências em saúde mental e analisar como se desenvolve a abordagem da equipe de enfermagem ao usuário com transtorno mental em situação de emergência. Participaram 6 enfermeiros e 7 técnicos em enfermagem que atuam na emergência e internamento. Os dados foram obtidos mediante entrevista semi-estruturada e organizados em categorias temáticas. Para os participantes, emergências psiquiátricas são situações que apresentam risco de vida para a pessoa ou a terceiros. Como características de emergência citaram: comportamento agressivo e agitado, tentativa de suicídio e abuso de substâncias. A primeira impressão do comportamento do paciente e a tentativa de diálogo determinam quais condutas os profissionais adotam. Reconhecem dificuldade e despreparo na abordagem ao paciente. Conclui-se que há necessidade de educação permanente sobre novos serviços e adaptações dos existentes para o atendimento nessa área.

Nonfatal tool- or equipment-related injuries treated in US emergency departments among workers in the construction industry, 1998-2005.

Science.gov (United States)

Lipscomb, Hester J; Schoenfisch, Ashley L; Shishlov, Kirill S; Myers, Douglas J

2010-06-01

Individuals in the construction industry are exposed to a variety of tools and pieces of equipment as they work. Data from the National Institute for Occupational Safety and Health (NIOSH) occupational supplement to the National Electronic Injury Surveillance System (NEISS-Work) were used to characterize tool- and equipment-related injuries among workers in the construction industry that were treated in US emergency departments between 1998 and 2005. Based on a national stratified probability sample of US hospitals with 24 hr emergency services, NEISS-Work allows calculation of national injury estimates. Over the 8-year period between 1998 and 2005, we estimated 786,900 (95% CI 546,600-1,027,200) ED-treated tool- or equipment-related injuries identified by the primary or secondary source of injury code. These injuries accounted for a quarter of all ED-treated construction industry injuries. Although over 100 different tools or pieces of equipment were responsible for these injuries, seven were responsible for over 65% of the injury burden: ladders, nail guns, power saws, hammers, knives, power drills, and welding tools in decreasing order. Current injury estimates and their severity, marked by the proportion of cases that were not released after ED treatment, indicate interventions are particularly needed to prevent injuries associated with use of ladders as well as nail guns and power saws. Attention should focus on design and guarding to more efficiently prevent these injuries rather than simply calling for the training of workers in how to safely use a dangerous tool or piece of equipment. 2010 Wiley-Liss, Inc.

Emergency planning for fuel cycle facilities

International Nuclear Information System (INIS)

Lacey, L.R.

1991-01-01

In April 1989, NRC published new emergency planning regulations which apply to certain by-product, source, and special nuclear materials licensees including most fuel cycle facilities. In addition to these NRC regulations, other regulatory agencies such as EPA, OSHA, and DOT have regulations concerning emergency planning or notification that may apply to fuel cycle facilities. Emergency planning requirements address such areas as emergency classification, organization, notification and activation, assessment, corrective and protective measures, emergency facilities and equipment, maintaining preparedness, records and reports, and recovery. This article reviews applicable regulatory requirements and guidance, then concentrates on implementation strategies to produce an effective emergency response capability

Nuclear reactor equipped with a flooding tank and a residual heat removal and emergency cooling system

International Nuclear Information System (INIS)

Schabert, H.P.; Winkler, F.

1975-01-01

A description is given of a nuclear reactor such as a pressurized-water reactor or the like which is equipped with a flooding tank and a residual heat removal and emergency cooling system. The flooding tank is arranged within the containment shell at an elevation above the upper edge of the reactor core and contains a liquid for flooding the reactor core in the event of a loss of coolant

Emergency response exercise of laboratories equipped with gamma spectrometry

Energy Technology Data Exchange (ETDEWEB)

Mala, Helena; Rulik, Petr; Jezkova, Tereza; Beckova, Vera [National Radiation Protection Institute (SURO), 140 00 Praha 28 (Czech Republic)

2014-07-01

At present 7 laboratories equipped with semiconductor gamma spectrometry (HPGe detectors) are included in the Radiation Monitoring Network (RMN) in the Czech Republic. These laboratories have 31 spectrometric chains and approximately 20 'experts' and 70 'users' who would guarantee measurements during a radiological emergency (RE). The stress exercise (a load test) was carried out in 4 of them. The aim was to test their measuring capacity in existing technical facilities and staff in the event of a RE and identify problems (bottlenecks) in the whole process from receipt of samples to entering the results into the central database of RMN. Duration of the exercise was 8 to 14 hours. Due to lack of staff, work in one 12-hour shift during a RE is presumed, which the laboratories should be able to provide for 14 days. Exercise samples covered a wide range of commodities that would probably come to the laboratories during RE (aerosol filters, adsorbed gaseous forms of iodine, fallout, surface and drinking waters, food chain components and soils). Some of the samples were previously spiked with {sup 85}Sr, {sup 88}Y and {sup 40}K (these nuclides represented actual nuclides that would occur in RE); soil samples contained higher values of {sup 137}Cs activity originating from the Chernobyl accident. Almost 40 employees took part in the exercise and measurements were carried out at 18 spectrometric chains. An automatic gamma counter which allows automatic operation of two HPGe detectors including the analysis of the spectra with a storage for up to 180 sample containers was operating in one of the laboratories involved in the exercise. The procedures in individual laboratories varied slightly depending on the staff and laboratory space available. During the exercise about 700 samples were evaluated; in addition, gamma-automat measured other 80 samples in the 'night shift'. 700 samples, this means 40 samples per a spectrometric chain or, from

Human Reliability Analysis for In-Tank Precipitation Alignment and Startup of Emergency Purge Ventilation Equipment. Revision 4

International Nuclear Information System (INIS)

Shapiro, B.J.; Britt, T.E.

1995-06-01

This report documents the methodology used for calculating the human error probability for establishing air based ventilation using emergency purge ventilation equipment on In-Tank Precipitation (ITP) processing tanks 48 and 49 after a failure of the nitrogen purge system following a seismic event. The analyses were performed according to THERP (Technique for Human Error Rate Prediction) as describes in NUREG/CR-1278-F

77 FR 43481 - Taking Additional Steps to Address the National Emergency With Respect to Somalia

Science.gov (United States)

2012-07-24

... Additional Steps to Address the National Emergency With Respect to Somalia #0; #0; #0; Presidential Documents... Additional Steps to Address the National Emergency With Respect to Somalia By the authority vested in me as... Somalia declared in Executive Order 13536 of April 12, 2010, in view of United Nations Security Council...

[The real-world effectiveness of personal protective equipment and additional risks for workers' health].

Science.gov (United States)

Denisov, É I; Morozova, T V; Adeninskaia, E E; Kur'erov, N N

2013-01-01

The effectiveness of personal protective equipment (PPE) of hearing, respiratory organs and hands is considered. It is shown that real effect of PPE is twice lower than declared by supplier; this presumes some derating system. The aspects of discomfort and additional risks are analyzed. The hygienic and physiologic evaluation of PPE is required along with elaboration of an official document (OSH standard or sanitary regulation) on selection, personal fit, organization of use and individual training of workers and their motivation.

Techniques and Emerging Trends for State of the Art Equipment Maintenance Systems—A Bibliometric Analysis

Directory of Open Access Journals (Sweden)

Burkhard Hoppenstedt

2018-06-01

Full Text Available The increasing interconnection of machines in industrial production on one hand, and the improved capabilities to store, retrieve, and analyze large amounts of data on the other, offer promising perspectives for maintaining production machines. Recently, predictive maintenance has gained increasing attention in the context of equipment maintenance systems. As opposed to other approaches, predictive maintenance relies on machine behavior models, which offer several advantages. In this highly interdisciplinary field, there is a lack of a literature review of relevant research fields and realization techniques. To obtain a comprehensive overview on the state of the art, large data sets of relevant literature need to be considered and, best case, be automatically partitioned into relevant research fields. A proper methodology to obtain such an overview is the bibliometric analysis method. In the presented work, we apply a bibliometric analysis to the field of equipment maintenance systems. To be more precise, we analyzed clusters of identified literature with the goal to obtain deeper insight into the related research fields. Moreover, cluster metrics reveal the importance of a single paper and an investigation of the temporal cluster development indicates the evolution of research topics. In this context, we introduce a new measure to compare results from different time periods in an appropriate way. In turn, among others, this simplifies the analysis of topics, with a vast amount of subtopics. Altogether, the obtained results particularly provide a comprehensive overview of established techniques and emerging trends for equipment maintenance systems.

The human failure factors during emergency operating

International Nuclear Information System (INIS)

Liu Bingji

1994-01-01

In the case of emergency operating, operating staff usually are in the limit state of mind, so the operating mistake rate will go up sharply, and the disastrous accidents usually will happen at this moment. So to study and resolve the problem is very important and imperative. Basing on raising the reliability of man-machine system, the psychology and pathology of operating staff under the limit state and the behavior characteristic of operating staff in the emergency operation have been expounded here, and the operating staff's psychological gradation partitioned by foreign experts also has been introduced, and the influence factors of psychology and equipment which lead to the limit state of mind also have been analyzed. In addition, taking the emergency operation of the nuclear power plant as a example, The authors has studied the countermeasures to prevent the limit state from occurring, which includes countermeasures to environment effects, measures to improve the technical equipment and the measures that the operating staff should be taken

US DOE Radiological Assistance Program: personnel, equipment and resources

International Nuclear Information System (INIS)

Hull, A.P.; Kuehner, A.V.; Phillips, L.F.

1982-01-01

The Radiological Assistance Program (RAP) of the US Department of Energy (DOE) is intended to provide emergency advice and assistance in the event of radiological incidents. Each of DOE's eight Regional Coordinating Offices in the US provide a 24-hour reporting and response capability. Specifically, the Brookhaven Area Office (BHO) is responsible for DOE's Region I, which includes the 11 northeastern states of the US. Although an inventory of dedicated equipment is assigned to BHO-RAP, it draws upon the resources of Brookhaven National Laboratory (BNL) for trained personnel in health physics and for other specialized personnel in both the day to day operation of the program and in the on-the-scene response to an incident. The organization of the BHO-RAP program and its response procedures are described in detail. An inventory and brief description of the contents of a variety of emergency equipment kits and of additional state-of-the-art instruments is included. The BHO-RAP guidelines and requirements for field operations are also indicated, as are other DOE resources upon which it can draw

Video-Based Learning vs Traditional Lecture for Instructing Emergency Medicine Residents in Disaster Medicine Principles of Mass Triage, Decontamination, and Personal Protective Equipment.

Science.gov (United States)

Curtis, Henry A; Trang, Karen; Chason, Kevin W; Biddinger, Paul D

2018-02-01

Introduction Great demands have been placed on disaster medicine educators. There is a need to develop innovative methods to educate Emergency Physicians in the ever-expanding body of disaster medicine knowledge. The authors sought to demonstrate that video-based learning (VBL) could be a promising alternative to traditional learning methods for teaching disaster medicine core competencies. Hypothesis/Problem The objective was to compare VBL to traditional lecture (TL) for instructing Emergency Medicine residents in the American College of Emergency Physicians (ACEP; Irving, Texas USA) disaster medicine core competencies of patient triage and decontamination. A randomized, controlled pilot study compared two methods of instruction for mass triage, decontamination, and personal protective equipment (PPE). Emergency Medicine resident learning was measured with a knowledge quiz, a Likert scale measuring comfort, and a practical exercise. An independent samples t-test compared the scoring of the VBL with the TL group. Twenty-six residents were randomized to VBL (n=13) or TL (n=13). Knowledge score improvement following video (14.9%) versus lecture (14.1%) did not differ significantly between the groups (P=.74). Comfort score improvement also did not differ (P=.64) between video (18.3%) and lecture groups (15.8%). In the practical skills assessment, the VBL group outperformed the TL group overall (70.4% vs 55.5%; Plearning vs traditional lecture for instructing emergency medicine residents in disaster medicine principles of mass triage, decontamination, and personal protective equipment. Prehosp Disaster Med. 2018;33(1):7-12.

Current state of commercial radiation detection equipment for homeland security applications

International Nuclear Information System (INIS)

Klann, R.T.; Shergur, J.; Mattesich, G.

2009-01-01

With the creation of the U.S. Department of Homeland Security (DHS) came the increased concern that terrorist groups would attempt to manufacture and use an improvised nuclear device or radiological dispersal device. As such, a primary mission of DHS is to protect the public against the use of these devices and to assist state and local responders in finding, locating, and identifying these types of devices and materials used to manufacture these devices. This assistance from DHS to state and local responders comes in the form of grant money to procure radiation detection equipment. In addition to this grant program, DHS has supported the development of American National Standards Institute standards for radiation detection equipment and has conducted testing of commercially available instruments. This paper identifies the types and kinds of commercially available equipment that can be used to detect and identify radiological material - for use in traditional search applications as well as primary and secondary screening of personnel, vehicles, and cargo containers. In doing so, key considerations for the conduct of operations are described as well as critical features of the instruments for specific applications. The current state of commercial instruments is described for different categories of detection equipment including personal radiation detectors, radioisotope identifiers, man-portable detection equipment, and radiation portal monitors. In addition, emerging technologies are also discussed, such as spectroscopic detectors and advanced spectroscopic portal monitors

Human Reliability Analysis for In-Tank Precipitation Alignment and Startup of Emergency Purge Ventilation Equipment. Revision 3

International Nuclear Information System (INIS)

Shapiro, B.J.; Britt, T.E.

1994-10-01

This report documents the methodology used for calculating the human error probability for establishing air based ventilation using emergency purge ventilation equipment on In-Tank Precipitation (ITP) processing tanks 48 and 49 after failure of the nitrogen purge system following a seismic event. The analyses were performed according to THERP (Technique for Human Error Rate Prediction) as described in NUREG/CR-1278-F, ''Handbook of Human Reliability Analysis with Emphasis on Nuclear Power Plant Applications.'' The calculated human error probabilities are provided as input to the Fault Tree Analysis for the ITP Nitrogen Purge System

Proposal for the award of a blanket contract for the supply and installation of automatic fire-detection and emergency-evacuation equipment

CERN Document Server

2003-01-01

This document concerns the award of a blanket contract for the supply and installation of automatic fire-detection and emergency-evacuation equipment. Following a market survey carried out among 54 firms in ten Member States, a call for tenders (IT-3090/ST) was sent on 29 August 2003 to one firm and four consortia in five Member States. By the closing date, CERN had received four tenders from four consortia in four Member States. The Finance Committee is invited to agree to the negotiation of a blanket contract with the consortium HEKATRON (DE) - SOTEB (FR), the lowest bidder, for the supply and installation of automatic fire-detection and emergency-evacuation equipment for a total amount not exceeding 1 900 000 euros (2 946 650 Swiss francs), subject to revision for inflation from 1 January 2007. The rate of exchange used is that stipulated in the tender. The firm has indicated the following distribution by country of the contract value covered by this adjudication proposal: DE - 70%; FR - 30%.

Reliability performance of standby equipment with periodic testing

International Nuclear Information System (INIS)

Sim, S.H.

1985-11-01

In this report, the reliability performance of standby equipment subjected to periodic testing is studied. analytical expressions have been derived for reliability measures, such as the man accumulated operating time to failure, the expected number of tests between two consecutive failures, the mean time to failure following an emergency start-up and the probability of failing to complete an emergency mission of a specified duration. These results are useful for the reliability assessment of standby equipment such as combustion turbine units of the emergency power supply system, and of the Class III power system at a nuclear generating station

Use of accident experience in developing criteria for teleoperator equipment

International Nuclear Information System (INIS)

Vallario, E.J.; Selby, J.M.

1985-10-01

The 1961 SL-1 reactor accident in Idaho and the Recuplex accident at Hanford are reviewed to identify problems common to emergency situations, lessons learned from accidents, criteria for emergency equipment, and recommendations for using robotics to solve problems during emergencies. Teleoperator equipment could be used to assess the extent of the damage and the condition of the reactor, retrieve dosimeters, evacuate and treat accident victims, clean up debris and decontaminate accident areas. 2 refs., 9 figs

29 CFR 541.706 - Emergencies.

Science.gov (United States)

2010-07-01

... damage to the employer's property, any work performed in an effort to prevent such results is considered... is not emergency work, even when necessary to prevent fire or explosion; however, repairing equipment may be emergency work if the breakdown of or damage to the equipment was caused by accident or...

Diagnostics of heavy mining equipment during the scheduled preventive maintenance

Science.gov (United States)

Drygin, M. Yu; Kuryshkin, N. P.

2018-01-01

Intensification of production, economic globalization and dramatic downgrade of the workers’ professional skills lead to unacceptable technical state of heavy mining equipment. Equipment maintenance outage reaches 84 % of the total downtime, of which emergency maintenance takes up to 36 % of time, that excesses 429 hours per year fr one excavator. It is shown that yearly diagnostics using methods of non-destructive check allows to reduce emergency downtime by 47 %, and 55 % of revealed defects can be eliminated without breaking the technological cycle of the equipment.

14 CFR 91.503 - Flying equipment and operating information.

Science.gov (United States)

2010-01-01

... Turbine-Powered Multiengine Airplanes and Fractional Ownership Program Aircraft § 91.503 Flying equipment...) Emergency operation of fuel, hydraulic, electrical, and mechanical systems. (2) Emergency operation of...

Medical emergency management among Iranian dentists.

Science.gov (United States)

Khami, Mohammad Reza; Yazdani, Reza; Afzalimoghaddam, Mohammad; Razeghi, Samaneh; Moscowchi, Anahita

2014-11-01

More than 18,000 patients need medical emergencies management in dental offices in Iran annually. The present study investigates medical emergencies management among Iranian dentists. From the list of the cell phone numbers of the dentists practicing in the city of Tehran, 210 dentists were selected randomly. A self-administered questionnaire was used as the data collection instrument. The questionnaire requested information on personal and professional characteristics of the dentists, as well as their knowledge and self-reported practice in the field of medical emergency management, and availability of required drugs and equipments to manage medical emergencies in their offices. Totally, 177 dentists (84%) completed the questionnaire. Less than 60% of the participants were knowledgeable about characteristics of hypoglycemic patient, chest pain with cardiac origin, and true cardiopulmonary resuscitation (CPR) practice. Regarding practice, less than one quarter of the respondents acquired acceptable scores. In regression models, higher practice scores were significantly associated with higher knowledge scores (p < 0.001). The results call for a need to further education on the subject for dentists. Continuing education and changing dental curriculum in the various forms seems to be useful in enhancement of the self-reported knowledge and practice of dentists. To successful control of medical emergencies in the dental office, dentists must be prepared to recognize and manage a variety of such conditions. In addition to dentist's knowledge and skill, availability of necessary equipments and trained staff is also of critical importance.

[A young child with respiratory acidosis and hypoxia from mechanical ventilation with equipment made for adults].

Science.gov (United States)

Joor, Fleur; Markhorst, Dick G; Kneyber, Martin C J; van Heerde, Marc

2011-01-01

During mechanical ventilation of young children, problems may arise due to the additional dead space of the ventilation circuit. This may lead to respiratory acidosis and even hypoxia in the child. A 3-month-old boy suffered from frequent apnoea. He was mechanically ventilated for this. Shortly after its initiation, he developed severe respiratory acidosis, hypoxemia and circulatory insufficiency. This was due to a large additional dead space caused by the use of equipment components made for adults. After he was switched to a circuit suitable for himself, he recovered rapidly. As a rule of thumb, an additional dead space of 1.5-2 ml/kg body weight is acceptable in young children. Emergency wards for young children should have specific equipment to mechanically ventilate them, and have a protocol paying explicit attention to the dead space.

Medical emergencies in dental practice.

LENUS (Irish Health Repository)

Wilson, M H

2009-06-01

Serious medical emergencies are fortunately a rare occurrence in the dental practice environment; however, if an emergency situation is encountered a delay in treatment may result in potentially avoidable consequences. The risk of mortality or serious morbidity can be reduced by ensuring that basic emergency equipment and medications are in place, and that the dental team is appropriately trained in basic life support measures. This article aims to provide an overview of the basic emergency medications and equipment that should be present in dental practices, and to discuss specific responses to some of the more common adverse medical events that can present while providing dental treatment.

Emergency preparedness lessons from Chernobyl

International Nuclear Information System (INIS)

Martin, J.B.

1987-09-01

Emergency preparedness at nuclear power plants in the US has been considerably enhanced since the Three Mile Island accident. The Chernobyl accident has provided valuable data that can be used to evaluate the merit of some of these enhancements and to determine the need for additional improvements. For example, the USSR intervention levels of 25 rem and 75 rem for evacuation are contrasted with US Environmental Protection Agency protective action guides. The manner in which 135,000 persons were evacuated from the 30-km zone around Chernobyl is constrasted with typical US evacuation plans. Meteorological conditions and particulate deposition patterns were studied to infer characteristics of the radioactive plume from Chernobyl. Typical plume monitoring techniques are examined in light of lessons learned by the Soviets about plume behavior. This review has indicated a need for additional improvements in utility and government emergency plans, procedures, equipment, and training. 12 refs., 1 fig., 2 tabs

Use of Equipment Information System (EQUIS) to determine priority for purchasing safeguards equipment

International Nuclear Information System (INIS)

Silberberg, S.

1988-01-01

To manage its large world-wide inventory of safeguards equipment, the IAEA Safeguards department uses a computerized Equipment Information System (EQUIS). EQUIS data have been analyzed using Queueing Theory to determine if inventory is adequate to meet inspector demands and in those cases where it is inadequate, to indicate how many additional units should be procured. Results are tabulated for various types of non-destructive analysis (NDA) equipment. For equipment where there is a high turnover and hence a large amount of data, the analysis provides a powerful tool for assisting procurement decisions

Additional helmet and pack loading reduce situational awareness during the establishment of marksmanship posture.

Science.gov (United States)

Lim, Jongil; Palmer, Christopher J; Busa, Michael A; Amado, Avelino; Rosado, Luis D; Ducharme, Scott W; Simon, Darnell; Van Emmerik, Richard E A

2017-06-01

The pickup of visual information is critical for controlling movement and maintaining situational awareness in dangerous situations. Altered coordination while wearing protective equipment may impact the likelihood of injury or death. This investigation examined the consequences of load magnitude and distribution on situational awareness, segmental coordination and head gaze in several protective equipment ensembles. Twelve soldiers stepped down onto force plates and were instructed to quickly and accurately identify visual information while establishing marksmanship posture in protective equipment. Time to discriminate visual information was extended when additional pack and helmet loads were added, with the small increase in helmet load having the largest effect. Greater head-leading and in-phase trunk-head coordination were found with lighter pack loads, while trunk-leading coordination increased and head gaze dynamics were more disrupted in heavier pack loads. Additional armour load in the vest had no consequences for Time to discriminate, coordination or head dynamics. This suggests that the addition of head borne load be carefully considered when integrating new technology and that up-armouring does not necessarily have negative consequences for marksmanship performance. Practitioner Summary: Understanding the trade-space between protection and reductions in task performance continue to challenge those developing personal protective equipment. These methods provide an approach that can help optimise equipment design and loading techniques by quantifying changes in task performance and the emergent coordination dynamics that underlie that performance.

Guidelines for nuclear reactor equipments safety-analysis

International Nuclear Information System (INIS)

1978-01-01

The safety analysis in approving the applications for nuclear reactor constructions (or alterations) is performed by the Committee on Examination of Reactor Safety in accordance with various guidelines prescribed by the Atomic Energy Commission. In addition, the above Committee set forth its own regulations for the safety analysis on common problems among various types of nuclear reactors. This book has collected and edited those guidelines and regulations. It has two parts: Part I includes the guidelines issued to date by the Atomic Energy Commission: and Part II - regulations of the Committee. Part I has collected 8 categories of guidelines which relate to following matters: nuclear reactor sites analysis guidelines and standards for their applications; standard exposure dose of plutonium; nuclear ship operation guidelines; safety design analysis guidelines for light-water type, electricity generating nuclear reactor equipments; safety evaluation guidelines for emergency reactor core cooling system of light-water type power reactors; guidelines for exposure dose target values around light-water type electricity generating nuclear reactor equipments, and guidelines for evaluation of above target values; and meteorological guidelines for the safety analysis of electricity generating nuclear reactor equipments. Part II includes regulations of the Committee concerning - the fuel assembly used in boiling-water type and in pressurized-water type reactors; techniques of reactor core heat designs, etc. in boiling-water reactors; and others

Multi-drug resistant Staphylococcus aureus isolated from emergency ...

African Journals Online (AJOL)

Purpose: To study the prevalence of resistant strains of S. aureus isolated from surfaces, beds and various equipment of an Iranian hospital emergency ward. Methods: Two hundred swab samples were collected from the surfaces, beds, trolleys, surgical equipment and diagnostic medical devices in emergency ward.

Preventative maintenance plan for emergency pumping trailers

International Nuclear Information System (INIS)

Wiggins, D.D.

1994-09-01

The purpose/goal of this document is to identify the maintenance requirements and resources available to properly maintain the readiness and condition of the Emergency Pumping Equipment controlled by the Tank Waste Remediation System Tank Farms Plant Engineering and Tank Stabilization Operations. This equipment is intended to pump a single-shell tank (SST) that has been identified as an assumed leaking tank. The goal is to commence pumping (submersible or jet) as soon as safely possible after identifying a SST as an assumed leaking tank. Important information pertaining to the Emergency Pumping Equipment, Over-Ground Piping installation, and procedures is found in WHC-SD-WM-AP-005, ''Single Shell Tank Leak Emergency Pumping Guide.''

Radiation therapy sources, equipment and installations

International Nuclear Information System (INIS)

2011-03-01

The safety code for Telegamma Therapy Equipment and Installations, (AERB/SC/MED-1) and safety code for Brachytherapy Sources, Equipment and Installations, (AERB/SC/MED-3) were issued by AERB in 1986 and 1988 respectively. These codes specified mandatory requirements for radiation therapy facilities, covering the entire spectrum of operations ranging from the setting up of a facility to its ultimate decommissioning, including procedures to be followed during emergency situations. The codes also stipulated requirements of personnel and their responsibilities. With the advent of new techniques and equipment such as 3D-conformal radiation therapy, intensity modulated radiation therapy, image guided radiation therapy, treatment planning system, stereotactic radiosurgery, stereotactic radiotherapy, portal imaging, integrated brachytherapy and endovascular brachytherapy during the last two decades, AERB desires that these codes be revised and merged into a single code titled Radiation Therapy Sources, Equipment, and Installations

PFP Emergency Lighting Study

International Nuclear Information System (INIS)

BUSCH, M.S.

2000-01-01

NFPA 101, section 5-9 mandates that, where required by building classification, all designated emergency egress routes be provided with adequate emergency lighting in the event of a normal lighting outage. Emergency lighting is to be arranged so that egress routes are illuminated to an average of 1.0 footcandle with a minimum at any point of 0.1 footcandle, as measured at floor level. These levels are permitted to drop to 60% of their original value over the required 90 minute emergency lighting duration after a power outage. The Plutonium Finishing Plant (PFP) has two designations for battery powered egress lights ''Emergency Lights'' are those battery powered lights required by NFPA 101 to provide lighting along officially designated egress routes in those buildings meeting the correct occupancy requirements. Emergency Lights are maintained on a monthly basis by procedure ZSR-12N-001. ''Backup Lights'' are battery powered lights not required by NFPA, but installed in areas where additional light may be needed. The Backup Light locations were identified by PFP Safety and Engineering based on several factors. (1) General occupancy and type of work in the area. Areas occupied briefly during a shiftly surveillance do not require backup lighting while a room occupied fairly frequently or for significant lengths of time will need one or two Backup lights to provide general illumination of the egress points. (2) Complexity of the egress routes. Office spaces with a standard hallway/room configuration will not require Backup Lights while a large room with several subdivisions or irregularly placed rooms, doors, and equipment will require Backup Lights to make egress safer. (3) Reasonable balance between the safety benefits of additional lighting and the man-hours/exposure required for periodic light maintenance. In some plant areas such as building 236-Z, the additional maintenance time and risk of contamination do not warrant having Backup Lights installed in all rooms

Selection of Additive Manufacturing (AM) Equipment

Science.gov (United States)

2017-04-01

FOLLOW THE PROCEDURES IN DoD 5200.22-M, INDUSTRIAL SECURITY MANUAL, SECTION II-19 OR DoD 5200.1-R, INFORMATION SECURITY PROGRAM REGULATION...axis subtractive machining center. The hybrid approach is gaining interest in the traditionally subtractive machine tool industry as the additive...systems typically consists of a build vat, feedstock hoppers , a material spreading device, and an energy source. The material spreading device

Off-site response for radiological emergencies

International Nuclear Information System (INIS)

Eldridge, J.S.; Oakes, T.W.; Hubbard, H.M.; Hibbitts, H.W.

1982-01-01

Environmental radiological surveillance under emergency conditions at off-site locations is one of the advisory functions provided by DOE within the ORO jurisdiction. The Department of Environmental Management of ORNL has been requested to provide sampling and analytical assistance at such emergency response activities. We have assembled and identified specific individuals and equipment to provide a rapid response force to perform field measurements for environmental radioactivity releases as a consequence of nuclear accidents. Survey teams for sample collection and field measurements are provided along with analytical assistance to operate the radioactivity measuring equipment in the DOE emergency van

Emerging new modalities in dental radiology and radiation issues

International Nuclear Information System (INIS)

Gandhi, Rahul

2014-01-01

Dental radiology is emerging day by day with technological innovations and new dental radiological equipments. These sophisticated new emerging technological raise a concern about the radiation emitted by these equipments. This becomes more relevant in the context that there is frequent diagnostic radiographic exposure of head and neck region due to recurrent dental problems. The presentation deals with radiation exposure to the patients and professionals from these equipments. (author)

Vibration aging of diesel-engine mounted electrical equipment

International Nuclear Information System (INIS)

Lee, B.J.; Morton, W.C.

1994-01-01

The Emergency Diesel Generator (EDG) in a Nuclear Power Plant is considered to be a component which is essential to safe plant operation. Failures of auxiliary equipment directly mounted on the EDG creates costly repairs, and compromises the engine's availability and reliability. Although IEEE-323 requires addressing of safety-related components due to mechanically induced vibration, very few guidelines exist in the nuclear industry to show how this may be accounted for. Most engine vendors rely on the empirical experience data as the basis of their evaluation for vibration. Upgrade of engine controls, addition of monitoring devices and other engine modifications require design and installation of new equipment to be mounted directly on the engine. This necessitates the evaluation for engine-induced vibration which is considered to be one of the most severe design parameters. This paper discusses the engine vibration characteristics, and the acquisition of extensive field vibration data on the diesel engine under operating conditions. The data is then used to develop life cycle vibration qualification test profiles that can be applied with confidence in a laboratory environment to qualify engine-mounted equipment. The intent is to validate a product's ability to survive under worst case, extended service on-engine conditions. This paper describes the procedures and approaches used to achieve those goals, and provides developed profile examples and test results

Inspection of Emergency Arrangements

International Nuclear Information System (INIS)

2013-01-01

NPPs. - Where RBs have an influence over land use around NPPs, they use the knowledge of their local or resident inspectors to inform decisions. - Inspectors check that appropriate action levels or criteria to identify an actual or radiological emergency are clearly defined and readily available to decision makers. - When observing emergency exercises inspectors check that: an appropriate and timely declaration is made, plant operators respond in accordance with the emergency plan and emergency instructions, and an appropriate level of response is initiated on and off-site. - RBs conduct follow-up inspections after real events, to ensure that the correct emergency response has been followed. - Inspectors verify that reliable data will be used to support the evaluation of environmental impact from a nuclear or radiological emergency, to the extent that this is within the jurisdiction of the RB. - Routine inspections and emergency exercise observations include a check that lines of communication are sufficiently resilient. - When observing emergency exercises inspectors, where practicable, check that timely, accurate and consistent information is provided to the public, in accordance with the off-site emergency plan. - RBs inspect the ability of the operator to give accurate medical and radiological information about casualties, to enable the correct treatment to be given. - Additional emergency equipment that is held in reserve off-site, provided to enhance resilience (post Fukushima), is included in the RB planned inspection and/or emergency exercise programme. - Inspectors check that licensee staff are adequately trained to connect and use additional equipment provided to enhance resilience. - Inspectors utilise the NPP operator's approved on-site emergency plan when inspecting on-site emergency arrangements. - RBs include human factors staff in emergency exercise evaluation teams to consider safety culture and human performance. - RBs consider the need for exercise

State of emergency medicine in Azerbaijan.

Science.gov (United States)

Sule, Harsh; Kazimov, Shirin; Shahmaliyev, Oktay; Sirois, Adam

2008-04-01

There has been no previous study into the state of emergency medicine in Azerbaijan. As a legacy of the Soviet Semashko system, the "specialty" model of emergency medicine and integrated emergency departments do not exist here. Instead, pre-hospital emergency care is delivered by ambulance physicians and in-hospital care by individual departments, often in specialty hospitals. Emergency care is therefore fragmented, highly specialized and inefficient. The Emergency Medicine Development Initiative (EMDI) of the International Medical Corps (IMC) was designed to improve the quality of emergency care in four pilot regional centers in Azerbaijan. The objective of this study was to assess the baseline emergency medical capacity of these four centers. EMDI staff conducted a four-part baseline survey in April 2006 to assess emergency care in Ganja (the second largest city in Azerbaijan), Kurdamir, Shamkir and Yevlakh. Data collection involved interviews with relevant personnel and a retrospective records review in each city. Pre-hospital: The number of ambulance teams per 10,000 inhabitants is below the number required by local regulations. On average, 45% of 27 medications and 37% of 17 pieces of critical equipment were available. Of the emergency procedures, 21% could be performed in the pre-hospital setting. In-hospital: Admission rates were near 100% for the admissions department-an area that is supposed to function as an emergency department would. On average 57% of 40 medications and 42% of 22 pieces of critical equipment were available. Of the emergency procedures, 62% could be performed in the in-hospital setting. The emergency medical system surveyed in Azerbaijan is inefficiently organized, under-financed, poorly equipped and lacks adequately trained staff. Reforms need to be directed towards achieving international standards, while adapting new models for service delivery into the existing framework and improving system capacity as highlighted by this baseline

An emergency response plan for transportation

International Nuclear Information System (INIS)

Fontaine, M.V.; Guerel, E.

2000-01-01

Transnucleaire is involved in road and rail transport of nuclear fuel cycle materials. To comply with IAEA recommendations, Transnucleaire has to master methods of emergency response in the event of a transport accident. Considering the utmost severe situations, Transnucleaire has studied several cases and focused especially on an accident involving a heavy cask. In France, the sub-prefect of each department is in charge of the organisation of the emergency teams. The sub-prefect may request Transnucleaire to supply experts, organisation, equipment and technical support. The Transnucleaire Emergency Response Plan covers all possible scenarios of land transport accidents and relies on: (i) an organisation ready for emergency situations, (ii) equipment dedicated to intervention, and (iii) training of its own experts and specialised companies. (author)

Integration of gamma measuring equipment into an Agusta A109BA helicopter of the Belgian Armed Forces for use in emergency situations

International Nuclear Information System (INIS)

Paridaens, J.

2007-01-01

In case of a nuclear emergency, accidental releases of radioactive material might cause large scale environmental contamination. After the emergency has been brought under control, and the radioactive releases have settled on the ground, it is essential to map as quickly as possible the extent of the contaminated area and to evaluate the severity of the contamination. Airborne gamma measurements are known to be an effective means for quickly and safely mapping and evaluating large scale contaminations of gamma-emitting radio nuclides. We wanted to integrate gamma measuring equipment, based on a NaI detector, into an Agusta A109BA helicopter of the Belgian armed forces. This was done within the framework of ''Aid to the Nation'', a special program developed by the Belgian Armed Forces for facilitating cooperation between the armed forces and civilian organisations, for projects that are to the benefit of the Belgian Nation. Working in this framework, we also want to develop the necessary procedures that will allow quick and efficient deployment of the measuring capability in case of an emergency

Improving the safety of remote site emergency airway management.

Science.gov (United States)

Wijesuriya, Julian; Brand, Jonathan

2014-01-01

Airway management, particularly in non-theatre settings, is an area of anaesthesia and critical care associated with significant risk of morbidity & mortality, as highlighted during the 4th National Audit Project of the Royal College of Anaesthetists (NAP4). A survey of junior anaesthetists at our hospital highlighted a lack of confidence and perceived lack of safety in emergency airway management, especially in non-theatre settings. We developed and implemented a multifaceted airway package designed to improve the safety of remote site airway management. A Rapid Sequence Induction (RSI) checklist was developed; this was combined with new advanced airway equipment and drugs bags. Additionally, new carbon dioxide detector filters were procured in order to comply with NAP4 monitoring recommendations. The RSI checklists were placed in key locations throughout the hospital and the drugs and advanced airway equipment bags were centralised in the Intensive Care Unit (ICU). It was agreed with the senior nursing staff that an appropriately trained ICU nurse would attend all emergency situations with new airway resources upon request. Departmental guidelines were updated to include details of the new resources and the on-call anaesthetist's responsibilities regarding checks and maintenance. Following our intervention trainees reported higher confidence levels regarding remote site emergency airway management. Nine trusts within the Northern Region were surveyed and we found large variations in the provision of remote site airway management resources. Complications in remote site airway management due lack of available appropriate drugs, equipment or trained staff are potentially life threatening and completely avoidable. Utilising the intervention package an anaesthetist would be able to safely plan and prepare for airway management in any setting. They would subsequently have the drugs, equipment, and trained assistance required to manage any difficulties or complications

A unique aerial platform equipped for large area surveillance: a real-time tool for emergency management

International Nuclear Information System (INIS)

Frullani, Salvatore; Castelluccio, Donato M.; Cisbani, Evaristo; Colilli, Stefano; Fratoni, Rolando; Giuliani, Fausto; Mostarda, Angelo; Colangeli, Giorgio; De Otto, Gian L.; Marchiori, Carlo; Paoloni, Gianfranco

2008-01-01

Aerial platform equipped with a sampling line and real-time monitoring of sampled aerosol is presented. The system is composed by: a) A Sky Arrow 650 fixed wing aircraft with the front part of the fuselage properly adapted to house the detection and acquisition equipment; b) A compact air sampling line where the iso kinetic sampling is dynamically maintained, aerosol is collected on a filter positioned along the line and hosted on a rotating 4-filters disk; c) A detection subsystem: a small BGO scintillator and Geiger counter right behind the sampling filter, a HPGe detector allows radionuclide identification in the collected aerosol samples, a large NaI(Tl) crystal detects airborne and ground gamma radiation; d) Several environmental (temperature, pressure, aircraft/wind speed) sensors and a GPS receiver that support the full characterization of the sampling conditions and the temporal and geographical location of the acquired data; e) Acquisition and control system based on compact electronics and real time software that operate the sampling line actuators, guarantee the dynamical iso kinetic condition, and acquire the detectors and sensor data. With this system quantitative measurements can be available also during the plume phase of an accident, while other aerial platforms, without sampling capability, can only be used for qualitative assessments. Transmission of all data will be soon implemented in order to make all the data available in real-time to the Technical Centre for the Emergency Management. The use of an unmanned air-vehicle (UAV) is discussed as future option. (author)

45 CFR 95.707 - Equipment management and disposition.

Science.gov (United States)

2010-10-01

... participation in the costs of replacement equipment shall be limited to the additional outlay. (4) If the... 45 Public Welfare 1 2010-10-01 2010-10-01 false Equipment management and disposition. 95.707... PROGRAMS) Equipment Acquired Under Public Assistance Programs § 95.707 Equipment management and disposition...

Assessing the Capacity of the US Health Care System to Use Additional Mechanical Ventilators During a Large-Scale Public Health Emergency.

Science.gov (United States)

Ajao, Adebola; Nystrom, Scott V; Koonin, Lisa M; Patel, Anita; Howell, David R; Baccam, Prasith; Lant, Tim; Malatino, Eileen; Chamberlin, Margaret; Meltzer, Martin I

2015-12-01

A large-scale public health emergency, such as a severe influenza pandemic, can generate large numbers of critically ill patients in a short time. We modeled the number of mechanical ventilators that could be used in addition to the number of hospital-based ventilators currently in use. We identified key components of the health care system needed to deliver ventilation therapy, quantified the maximum number of additional ventilators that each key component could support at various capacity levels (ie, conventional, contingency, and crisis), and determined the constraining key component at each capacity level. Our study results showed that US hospitals could absorb between 26,200 and 56,300 additional ventilators at the peak of a national influenza pandemic outbreak with robust pre-pandemic planning. The current US health care system may have limited capacity to use additional mechanical ventilators during a large-scale public health emergency. Emergency planners need to understand their health care systems' capability to absorb additional resources and expand care. This methodology could be adapted by emergency planners to determine stockpiling goals for critical resources or to identify alternatives to manage overwhelming critical care need.

Clinical audit of emergency unit before and after establishment of the emergency medicine department.

Science.gov (United States)

Amini, Afshin; Dindoost, Payam; Moghimi, Mehrdad; Kariman, Hamid; Shahrami, Ali; Dolatabadi, Ali Arhami; Ali-Mohammadi, Hossein; Alavai-Moghaddam, Mostafa; Derakhshanfar, Hojjat; Hatamabadi, HamidReza; Heidari, Kamran; Alamdari, Shahram; Meibodi, Mohammad Kalantar; Shojaee, Majid; Foroozanfar, Mohammad Mehdi; Hashemi, Behrooz; Sabzeghaba, Anita; Kabir, Ali

2012-02-01

To assess the deficiencies and potential areas through a medical audit of the emergency departments, in six general hospitals affiliated to Shahid Beheshti University of Medical Sciences at Tehran, Iran, after preparing specific wards-based international standards. A checklist was completed for all hospitals which met our eligibility criteria mainly observation and interviews with head nurses and managers of the emergency medicine unit of the hospitals before (2003) and after (2008) the establishment of emergency departments there. Domains studied included staffing, education and continuing professional development (CPD), facility (design), equipment, ancillary services, medical records, manuals and references, research, administration, pre-hospital care, information systems, disaster planning, bench-marking and hospital accreditation. Education and CPD (p = 0.042), design and facility (p = 0.027), equipment (p = 0.028), and disaster (p = 0.026) had significantly improved after the establishment of emergency departments. Nearly all domains showed a positive change though it was non-significant in a few. In terms of observation, better improvement was seen in disaster, security, design, and research. According to the score for each domain compared to what it was in the earlier phase, better improvement was observed in hospital accreditation, information systems, security, disaster planning, and research. Security, disaster planning, research, design and facility had improved in hospitals that wave studied, while equipment, records, ancillary services, administration and bench-marking had the lowest improvement even after the establishment of emergency department, and, hence, needed specific attention.

Emergency nurses' perceptions of emergency department preparedness for an ebola outbreak: A qualitative descriptive study.

Science.gov (United States)

Pincha Baduge, Mihirika Sds; Moss, Cheryle; Morphet, Julia

2017-05-01

Ebola Virus Disease is highly contagious and has high mortality. In 2014, when the outbreak in West Africa was declared a public health emergency, emergency departments in Australia commenced preparation and vigilance for people presenting with ebola like symptoms, to limit spread of the disease. To examine Australian emergency nurses' perceptions regarding their own and their emergency departments' preparedness to manage an ebola outbreak. A qualitative descriptive design was used to collect and analyse data in one metropolitan emergency department in Victoria, Australia. Four focus groups were conducted with 13 emergency nurses. Data were thematically analysed. Major themes emerged from the data: organisational, personal and future preparedness. Participants' believed that both the organisation and themselves had achieved desirable and appropriate preparedness for ebola in their emergency setting. Participants trusted their organisation to prepare and protect them for ebola. Appropriate policies, procedures, and equipment infrastructure were reportedly in place. Nurses' decisions to care for a patient with ebola were informed by professional commitment, and personal responsibilities. Participants were concerned about transmitting ebola to their families, and suggested that more regular training in personal protective equipment would increase confidence and skill in self-protection. Copyright © 2017 College of Emergency Nursing Australasia. Published by Elsevier Ltd. All rights reserved.

The Nuclear Emergency Assistance Team, an Institution for Nuclear Emergency Relief

Energy Technology Data Exchange (ETDEWEB)

Boldyreff, P.; Kiefer, H.; Krause, H.; Zuehlke, K. [Gesellschaft fuer Kernforschung mbH, Karlsruhe, Federal Republic of Germany (Germany)

1969-10-15

The design of nuclear facilities is to exclude serious damage to the environment, even in case of the MCA (maximum credible accident). Although the likelihood of accidents exceeding the expected consequences of the MCA is extremely small, it is deemed reasonable to take general precautions against such accidents. Precautions of this type are customary also in the conventional field, and in this case they are to be implemented in part through the Nuclear Emergency Assistance Team. If the internal safety provisions of a nuclear facility are unable to prevent an impermissible leakage of radioactivity as the result of a major accident there is, at present, no possibility of decisively curbing the spread of activity throughout the environment in the first few hours after the accident. Hence the measures taken by the authorities as a result of the emission and immediately following upon it will have to be restricted to the protection of the population: analysis of intensity and pattern of distribution of activity, instructions.to seek closed shelters, or prohibition of the consumption of certain foodstuffs, distribution of blocking agents, etc. It is the purpose of the Nuclear Emergency Assistance Team to bring relief in the phase following the end of the emission. This may comprise the following steps: exact investigation of the external scope of the damage, in particular assessment of the contamination of ground, persons, and material; rapid personnel decontamination; securing and shielding radiation sources; fixing contamination and removing it immediately where this is deemed urgent for reasons of traffic or to keep the drinking water free from contamination; external containment of the source of danger; support in limiting the damage within the facility. In addition to these tasks of emergency protection, the Nuclear Emergency Assistance Team can take action also in disturbances within the facility which have no influence on the environment and where the operator

Method of Data storing, collection and aggregation for definition of life-cycle resources of electromechanical equipment

Science.gov (United States)

Zhukovskiy, Y.; Koteleva, N.

2017-10-01

Analysis of technical and technological conditions for the emergence of emergency situations during the operation of electromechanical equipment of enterprises of the mineral and raw materials complex shows that when developing the basis for ensuring safe operation, it is necessary to take into account not only the technical condition, but also the non-stationary operation of the operating conditions of equipment, and the nonstationarity of operational operating parameters of technological processes. Violations of the operation of individual parts of the machine, not detected in time, can lead to severe accidents at work, as well as to unplanned downtime and loss of profits. That is why, the issues of obtaining and processing Big data obtained during the life cycle of electromechanical equipment, for assessing the current state of the electromechanical equipment used, timely diagnostics of emergency and pre-emergency modes of its operation, estimating the residual resource, as well as prediction the technical state on the basis of machine learning are very important. This article is dedicated to developing the special method of data storing, collection and aggregation for definition of life-cycle resources of electromechanical equipment. This method can be used in working with big data and can allow extracting the knowledge from different data types: the plants’ historical data and the factory historical data. The data of the plants contains the information about electromechanical equipment operation and the data of the factory contains the information about a production of electromechanical equipment.

Methodology for assessing laser-based equipment

Science.gov (United States)

Pelegrina-Bonilla, Gabriel; Hermsdorf, Jörg; Thombansen, Ulrich; Abels, Peter; Kaierle, Stefan; Neumann, Jörg

2017-10-01

Methodologies for the assessment of technology's maturity are widely used in industry and research. Probably the best known are technology readiness levels (TRLs), initially pioneered by the National Aeronautics and Space Administration (NASA). At the beginning, only descriptively defined TRLs existed, but over time, automated assessment techniques in the form of questionnaires emerged in order to determine TRLs. Originally TRLs targeted equipment for space applications, but the demands on industrial relevant equipment are partly different in terms of, for example, overall costs, product quantities, or the presence of competitors. Therefore, we present a commonly valid assessment methodology with the aim of assessing laser-based equipment for industrial use, in general. The assessment is carried out with the help of a questionnaire, which allows for a user-friendly and easy accessible way to monitor the progress from the lab-proven state to the application-ready product throughout the complete development period. The assessment result is presented in a multidimensional metric in order to reveal the current specific strengths and weaknesses of the equipment development process, which can be used to direct the remaining development process of the equipment in the right direction.

Quality assurance for radiodiagnostic equipment in Uruguay

International Nuclear Information System (INIS)

Cotelo, Elena D.

2001-01-01

Since Uruguay did not have an study on X-ray equipment, students of Radiation Protection course (RP) made this field work throughout the country. The objective is to obtain information on the number and kind of X-ray radiodiagnostic equipment. Some of the results are: there are 666 radiodiagnostic equipment. The ratio of population to equipment is 4.515 to 1 in the capital and the mean rate in the rest of the country is 4.383 to one, with a minimum of 1.707 and a maximum of 8.220. The Public Health Ministry (MSP) and the Instituciones de Asistencia Medica Colectiva (a kind of private heath assurance) (IAMC) have less equipment in the capital than in the rest of the country. The 37% of the capital population receives assistance through the IAMC , with a 42.5 % of the equipment. Uruguay except the capital has 18 districts and 17 computed tomography equipment, from which only 3 belong to the MSP. Five districts do not have any. In Montevideo, there are 11.500 females over forty years of age per X-ray mammography equipment, and this relation in the rest of the country is 13.900. There are 21 X-ray Interventional radiology equipment, 16 of them are in the capital. Is from relating the radiodiagnostic equipment, the population and the procedures, that quality assistance indicators emerge. This owns high importance on the way to create a RP National Programme. (author)

Alternative Fuel and Advanced Technology Commercial Lawn Equipment

Energy Technology Data Exchange (ETDEWEB)

None

2014-10-10

The U.S. Department of Energy's Clean Cities program produced this guide to help inform the commercial mowing industry about product options and potential benefits. This guide provides information about equipment powered by propane, ethanol, compressed natural gas, biodiesel, and electricity, as well as advanced engine technology. In addition to providing an overview for organizations considering alternative fuel lawn equipment, this guide may also be helpful for organizations that want to consider using additional alternative fueled equipment.

Radiological emergencies the first response

International Nuclear Information System (INIS)

2011-11-01

This national training course about radiological emergencies first answer include: Targets and preparation for emergency response in case of a nuclear or radiological accident. Operations center, action guide for fire fighting, medical coverage, forensic test, first aid, basic instrumentation for radiation, safety equipment, monitoring radiation, gamma rays, personnel exposed protection , radiation exposure rate, injury and illness for radiation, cancer risk, contamination, decontamination and treatment, markers, personnel dosimetry, training, medical and equipment transportation, shielded and tools. Psychological, physical (health and illness), economical (agriculture and industry) and environment impacts. Terrorist attacks, security belts. Support and international agreements (IAEA)

Methodology for Assessing Radiation Detectors Used by Emergency Responders

International Nuclear Information System (INIS)

Piotr Wasiolek; April Simpson

2008-01-01

The threat of weapons of mass destruction terrorism resulted in the U.S. Department of Homeland Security deploying large quantities of radiation detectors throughout the emergency responder community. However, emergency responders specific needs were not always met by standard health physics instrumentation used in radiation facilities. Several American National Standards Institute standards were developed and approved to evaluate the technical capabilities of detection equipment. Establishing technical capability is a critical step, but it is equally important to emergency responders that the instruments are easy to operate and can withstand the rugged situations they encounter. The System Assessment and Validation for Emergency Responders (SAVER) Program (managed by the U.S. Department of Homeland Security, Office of Grants and Training, Systems Support Division) focuses predominantly on the usability, ergonomics, readability, and other features of the detectors, rather than performance controlled by industry standards and the manufacturers. National Security Technologies, LLC, as a SAVER Technical Agent, conducts equipment evaluations using active emergency responders who are familiar with the detection equipment and knowledgeable of situations encountered in the field, which provides more relevant data to emergency responders

Emerging Applications for High K Materials in VLSI Technology

Science.gov (United States)

Clark, Robert D.

2014-01-01

The current status of High K dielectrics in Very Large Scale Integrated circuit (VLSI) manufacturing for leading edge Dynamic Random Access Memory (DRAM) and Complementary Metal Oxide Semiconductor (CMOS) applications is summarized along with the deposition methods and general equipment types employed. Emerging applications for High K dielectrics in future CMOS are described as well for implementations in 10 nm and beyond nodes. Additional emerging applications for High K dielectrics include Resistive RAM memories, Metal-Insulator-Metal (MIM) diodes, Ferroelectric logic and memory devices, and as mask layers for patterning. Atomic Layer Deposition (ALD) is a common and proven deposition method for all of the applications discussed for use in future VLSI manufacturing. PMID:28788599

Emerging Applications for High K Materials in VLSI Technology

Directory of Open Access Journals (Sweden)

Robert D. Clark

2014-04-01

Full Text Available The current status of High K dielectrics in Very Large Scale Integrated circuit (VLSI manufacturing for leading edge Dynamic Random Access Memory (DRAM and Complementary Metal Oxide Semiconductor (CMOS applications is summarized along with the deposition methods and general equipment types employed. Emerging applications for High K dielectrics in future CMOS are described as well for implementations in 10 nm and beyond nodes. Additional emerging applications for High K dielectrics include Resistive RAM memories, Metal-Insulator-Metal (MIM diodes, Ferroelectric logic and memory devices, and as mask layers for patterning. Atomic Layer Deposition (ALD is a common and proven deposition method for all of the applications discussed for use in future VLSI manufacturing.

A Simulation Learning Approach to Training First Responders for Radiological Emergencies

International Nuclear Information System (INIS)

Sanders, Robert Lon; Rhodes, Graham S.

2007-01-01

This paper describes the application of simulation learning technology, popularized by the emerging serious games industry, for training first responders to properly act in the event of a radiological emergency. Using state-of-the-art video game production tools and runtime engines as an enabling technology, simulation learning combines interactive virtual worlds based on validated engineering models with engaging storylines and scenarios that invoke the emotional response-and the corresponding human stress level-that first responders would encounter during a real-world emergency. For the application discussed here, in addition to providing engaging instruction about the fundamentals of radiological environments and the proper usage of radiological equipment, simulation learning prepares first responders to perform effectively under high stress and enables them to practice in teams

[Legionella pneumonia after the use of CPAP equipment].

Science.gov (United States)

Stolk, Jaap M; Russcher, Anne; van Elzakker, Erika P M; Schippers, Emile F

2016-01-01

Continuous positive airway pressure (CPAP) equipment can be colonised by Legionellae and might cause Legionella pneumonia in the user. However, there is no reported case of Legionella pneumonia related to CPAP equipment in which an identical Legionella was found in both the patient and the CPAP equipment. A 51-year-old man came to the Emergency Department with fever, confusion and dyspnoea that had been present for 3 days. His medical history included obstructive sleep apnoea, for which he had been using CPAP therapy at home for 10 weeks. The CPAP equipment showed signs of poor maintenance. Chest X-ray revealed a pulmonary consolidation. Laboratory investigation resulted in a positive urine antigen test for Legionella. Water from the CPAP equipment and sputum from the patient revealed Legionella pneumophila. Serotyping and sequence-based typing showed an identical L. pneumophila serotype 1 ST37. It is important to be aware that CPAP equipment can be colonised with Legionellae and might cause Legionella pneumonia. It is therefore necessary to ask about CPAP therapy in a patient with community-acquired pneumonia.

Making petroleum equipment safe, a priority

International Nuclear Information System (INIS)

1999-01-01

Changes to the 'Act respecting the use of petroleum products' have been announced effective May 1, 1999. The changes have been made to reduce problems which can be attributed to petroleum product leaks. The new regulations will make owners and users of petroleum equipment, including underground and above-ground storage equipment and commercial storage tanks, more accountable for the use of their own equipment. The emphasis in the new regulations is based upon the storage capacity of petroleum equipment and the risks associated with this equipment, rather than the on the activities of the owners concerned. Accordingly, the new regulations call for stricter requirements for high-risk equipment, a private equipment inspection plan, a two-year operating permit, replacing the current permits and certificates, a tariff structure based on the risks associated with the equipment, and deregulation of commercial activities involving petroleum products that require no equipment. Additionally, the amendments to the Act transfer responsibility for administration to the Regie du batiment and to the Ministere des Transports. Details of each of these changes are explained

Research on Modularized Design and Allocation of Infectious Disease Prevention and Control Equipment in China.

Science.gov (United States)

Zhao, Xin; Wang, Yun-Dou; Zhang, Xiao-Feng; Gao, Shu-Tian; Guo, Li-Jun; Sun, Li-Na

2017-06-01

For the prevention and control of newly emergent or sudden infectious diseases, we built an on-site, modularized prevention and control system and tested the equipment by using the clustering analysis method. On the basis of this system, we propose a modular equipment allocation method and 4 applications of this method for different types of infectious disease prevention and control. This will help to improve the efficiency and productivity of anti-epidemic emergency forces and will provide strong technical support for implementing more universal and serialized equipment in China. (Disaster Med Public Health Preparedness. 2017;11:375-382).

On-site emergency preparedness in Finland

International Nuclear Information System (INIS)

Vilkamo, O.

1998-01-01

General scheme of emergency preparedness in Finland is presented including legal framework, emergency organization and detailed description of plans and procedures. Emergency plan in Finland cover the following matters: classification of emergency situations and description of events and accidents, description of emergency organization, description of the arrangements for alerting and data transfer, management of an emergency situation and radiation protection, worker safety and radiation protection, on- and off-site radiation measurements during a preparedness situation, provision of information, rooms, equipment and facilities, post emergency debriefing and measures, a description of the maintenance of preparedness

Three equipment concepts for the Fusion Engineering Device

International Nuclear Information System (INIS)

Spampinato, P.T.; Masson, L.S.; Watts, K.D.; Grant, N.R.; Kuban, D.P.

1982-01-01

Maintenance equipment which is needed to remotely handle fusion device components is being conceptually developed for the Fusion Engineering Design Center. This will test the assumption that these equipment needs can be satisfied by present technology. In addition, the development of equipment conceptual designs will allow for cost estimates which have a much higher degree of certainty. Accurate equipment costs will be useful for assessments which trade off gains in availability as a function of increased investments in maintenance equipment

Alternative Fuel and Advanced Technology Commercial Lawn Equipment (Brochure)

Energy Technology Data Exchange (ETDEWEB)

2014-10-01

The U.S. Department of Energy's Clean Cities program produced this guide to help inform the commercial mowing industry about product options and potential benefits. This guide provides information about equipment powered by propane, ethanol, compressed natural gas, biodiesel, and electricity, as well as advanced engine technology. In addition to providing an overview for organizations considering alternative fuel lawn equipment, this guide may also be helpful for organizations that want to consider using additional alternative fueled equipment.

Emergency Care Capabilities in North East Haiti: A Cross-sectional Observational Study.

Science.gov (United States)

De Wulf, Annelies; Aluisio, Adam R; Muhlfelder, Dana; Bloem, Christina

2015-12-01

The North East Department is a resource-limited region of Haiti. Health care is provided by hospitals and community clinics, with no formal Emergency Medical System and undefined emergency services. As a paucity of information exists on available emergency services in the North East Department of Haiti, the objective of this study was to assess systematically the existing emergency care resources in the region. This cross-sectional observational study was carried out at all Ministry of Public Health and Population (MSPP)-affiliated hospitals in the North East Department and all clinics within the Fort Liberté district. A modified version of the World Health Organization (WHO) Tool for Situational Analysis to Assess Emergency and Essential Surgical Care and Generic Essential Emergency Equipment Lists were completed for each facility. Three MSPP hospitals and five clinics were assessed. Among hospitals, all had a designated emergency ward with 24 hour staffing by a medical doctor. All hospitals had electricity with backup generators and access to running water; however, none had potable water. All hospitals had x-ray and ultrasound capabilities. No computed tomography scanners existed in the region. Invasive airway equipment and associated medications were not present consistently in the hospitals' emergency care areas, but they were available in the operating rooms. Pulse oximetry was unavailable uniformly. One hospital had intermittently functioning defibrillation equipment, and two hospitals had epinephrine. Basic supplies for managing obstetrical and traumatic emergencies were available at all hospitals. Surgical services were accessible at two hospitals. No critical care services were available in the region. Clinics varied widely in terms of equipment availability. They uniformly had limited emergency medical equipment. The clinics also had inconsistent access to basic assessment tools (sphygmomanometers 20% and stethoscopes 60%). A protocol for transferring

44 CFR 208.37 - Reimbursement for equipment and supply costs incurred during Activation.

Science.gov (United States)

2010-10-01

... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Reimbursement for equipment... SEARCH AND RESCUE RESPONSE SYSTEM Response Cooperative Agreements § 208.37 Reimbursement for equipment and supply costs incurred during Activation. (a) Allowable costs. DHS will reimburse costs incurred...

Development of 3D Atlas of Metalworking Equipment

Science.gov (United States)

Yevgenyevna Maslennikova, Olga; Borisovna Nazarova, Olga; Aleksandrovna Chudinova, Yulia

2018-05-01

The paper is dedicated to solving the problem of developing innovative educational systems able to train personnel of complex and dangerous manufacturing industries (such as in metallurgy) to control the process not only under regular conditions, but in emergency and pre-emergency situations as well. At that, such educational systems shall transform training of future and current engineers into a professional activity, model both subject matter and social content of their professional labor. Key characteristics of a 3D atlas of equipment as an educational system are given, as it provides immersion of trainees into professional environment. Requirements for such systems are defined (functional, information, software and technical). Stages of development of a 3D atlas of equipment as an automated system are given, allowing one to get closer to yet another problem that of IT specialist training so that they are able to design, implement and deploy such systems.

Emergency response workers workshop

International Nuclear Information System (INIS)

Agapeev, S.A.; Glukhikh, E.N.; Tyurin, R.L.

2012-01-01

A training workshop entitled Current issues and potential improvements in Rosatom Corporation emergency prevention and response system was held in May-June, 2012. The workshop combined theoretical training with full-scale practical exercise that demonstrated the existing innovative capabilities for radiation reconnaissance, diving equipment and robotics, aircraft, emergency response and rescue hardware and machinery. This paper describes the activities carried out during the workshop [ru

Emergency management

International Nuclear Information System (INIS)

1996-01-01

In 1995, major efforts of the Nuclear Regulatory Authority of the Slovak Republic (NRA SR) were focused on tasks associated with completion and incorporation of the Emergency Response Centre (ERC) of NRA SR in emergency planning and crisis management. Construction of the ERC had begun based on NRA SR's knowledge, as well as recommendations of Regulatory Assistance Management Group (RAMG) International Mission in 1993 and follow-up missions in 1994. Early in 1994, re-construction of selected rooms had been done and early in 1995, supported by the UK and U.S.A. Government's funding, technical equipment was purchased. The equipment was necessary for ERC operation as tools to improve NRA SR readiness for the management of emergency situations at nuclear installations. NRA SR commenced operation of the Centre in April 1995. The Centre has been on-line connected to a teledosimetric system of Radiation Monitoring Laboratory in Trnava. The basic software for assessment of radiation consequences of a NPP accident was supplied were also focused on cooperation with state administration authorities and organizations which were involved in an emergency planning structure. In September 1995, staffing of the ERC was completed and parallel, the first document concerning the ERC prime task, i.e. activities and procedures of of NRA SR Crisis crew in case of an accident at a nuclear installation on the territory of the Slovak Republic, was approved by the NRA SR's Management. In the period that is being assessed, NRA SR made significant progress in events classification and emergency planning terminology in order to unify the above between both the Slovak NPPs

Football Equipment Removal Improves Chest Compression and Ventilation Efficacy.

Science.gov (United States)

Mihalik, Jason P; Lynall, Robert C; Fraser, Melissa A; Decoster, Laura C; De Maio, Valerie J; Patel, Amar P; Swartz, Erik E

2016-01-01

Airway access recommendations in potential catastrophic spine injury scenarios advocate for facemask removal, while keeping the helmet and shoulder pads in place for ensuing emergency transport. The anecdotal evidence to support these recommendations assumes that maintaining the helmet and shoulder pads assists inline cervical stabilization and that facial access guarantees adequate airway access. Our objective was to determine the effect of football equipment interference on performing chest compressions and delivering adequate ventilations on patient simulators. We hypothesized that conditions with more football equipment would decrease chest compression and ventilation efficacy. Thirty-two certified athletic trainers were block randomized to participate in six different compression conditions and six different ventilation conditions using human patient simulators. Data for chest compression (mean compression depth, compression rate, percentage of correctly released compressions, and percentage of adequate compressions) and ventilation (total ventilations, mean ventilation volume, and percentage of ventilations delivering adequate volume) conditions were analyzed across all conditions. The fully equipped athlete resulted in the lowest mean compression depth (F5,154 = 22.82; P Emergency medical personnel should remove the helmet and shoulder pads from all football athletes who require cardiopulmonary resuscitation, while maintaining appropriate cervical spine stabilization when injury is suspected. Further research is needed to confirm our findings supporting full equipment removal for chest compression and ventilation delivery.

Emergency preparedness post-9/11 enhancements at US nuclear plants

International Nuclear Information System (INIS)

Sullivan, R.L.

2005-01-01

Full text: In the wake of the terrorist attacks of 9-11, the US Nuclear Regulatory Commission (NRC) took several actions to improve the security profile and emergency response of its licensees. In early 2002 the commission issued orders to its nuclear power plant licensees which included changes to emergency plans, the performance of staffing adequacy reviews, changes to augmentation practices and the establishment of alternative facilities. Since that time NRC has implemented a force-on-force exercise program that includes emergency response. This program has helped licensees improve their response by testing procedures under simulated attack conditions. More recently, licensees have begun a program to enhance drills and exercises through the use of security event based scenarios. These drills will enhance previous practice and focus on two emerging issues: improving the interface between emergency response, security response and operations during security events and recovery from the loss of plant equipment due to terrorist acts. Additional areas of enhancement such as protective actions for plant personnel will also be discussed and the status of actions to date will be provided. (author)

Tube for irradiation equipment

International Nuclear Information System (INIS)

Goehrich, K.; Vogt, H.

1979-01-01

This patent describes a tube for irradiation equipment for limiting an emergent beam, with a baseplate, possessing a central aperture, intended for attaching to the equipment, as well as four carrier plates, each of which possesses a limiting edge and a sliding edge located at right angles thereto. The carrier plates are located parallel to the baseplate, the limiting edge of each carrier plate resting against the sliding edge of the adjacent carrier plate and each of the two mutually opposite pairs of carrier plates being displaceable, parallel to the direction of its sliding edges and symmetrically to the center of the transmission aperture, for the purpose of continuously varying the transmission aperture defined by the limiting edges, during which displacement each of the displaced carrier plates carries with it the carrier plate, resting against the limiting edge of the former plate, parallel to the direction of the limiting edge of the latter plate. 8 claims

The preparedness of private dental offices and polyclinics for medical emergencies

Science.gov (United States)

Al-Sebaei, Maisa O.; Alkayyal, Moayyad A.; Alsulimani, Abdulelah H.; Alsulaimani, Othman S.; Habib, Weam T.

2015-01-01

Objectives: To assess preparedness for medical emergencies in private dental offices in Jeddah, Kingdom of Saudi Arabia (KSA). Methods: In this cross-sectional study, a survey was distributed to 70 dental offices and polyclinics in Jeddah, Saudi Arabia between October 2013 and January 2014. The questionnaire gathered information on the prevention of medical emergencies, the preparedness of the office personnel, and availability of emergency drugs and equipment. Results: For prevention, 92% (n=65) of the offices reported that they obtain a thorough medical history prior to treatment; however, only 11% (n=8) obtain vital signs for each visit. Using a preparedness percent score (0 to 100), the mean level of preparedness of the office personnel in all surveyed dental offices was 55.2±20. The availability of emergency drugs was 35±35, and equipment was 19±22. Conclusion: We found a deficiency in personnel training, availability of drugs, and emergency equipment in the surveyed dental clinics. More stringent rules and regulations for emergency preparedness must be reinforced to avoid disasters in these clinics. PMID:25737177

Automatic monitoring of vibration welding equipment

Science.gov (United States)

Spicer, John Patrick; Chakraborty, Debejyo; Wincek, Michael Anthony; Wang, Hui; Abell, Jeffrey A; Bracey, Jennifer; Cai, Wayne W

2014-10-14

A vibration welding system includes vibration welding equipment having a welding horn and anvil, a host device, a check station, and a robot. The robot moves the horn and anvil via an arm to the check station. Sensors, e.g., temperature sensors, are positioned with respect to the welding equipment. Additional sensors are positioned with respect to the check station, including a pressure-sensitive array. The host device, which monitors a condition of the welding equipment, measures signals via the sensors positioned with respect to the welding equipment when the horn is actively forming a weld. The robot moves the horn and anvil to the check station, activates the check station sensors at the check station, and determines a condition of the welding equipment by processing the received signals. Acoustic, force, temperature, displacement, amplitude, and/or attitude/gyroscopic sensors may be used.

Double-shell tank emergency pumping guide

International Nuclear Information System (INIS)

BROWN, M.H.

1999-01-01

This Double-Shell Tank Emergency Pumping Guide provides the preplanning necessary to expeditiously remove any waste that may leak from the primary tank to the secondary tank for Hanfords 28 DSTs. The strategy is described, applicable emergency procedures are referenced, and transfer routes and pumping equipment for each tank are identified

Double-shell tank emergency pumping guide

International Nuclear Information System (INIS)

BROWN, M.H.

1999-01-01

This Double-Shell Tank Emergency Pumping Guide provides the preplanning necessary to expeditiously remove any waste that may leak from the primary tank to the secondary tank for Hanford's 28 DSTS. The strategy is described, applicable emergency procedures are referenced, and transfer routes and pumping equipment for each tank are identified

Lifetime of Mechanical Equipment

Energy Technology Data Exchange (ETDEWEB)

Leland, K.

1999-07-01

The gas plant at Kaarstoe was built as part of the Statpipe gas transport system and went on stream in 1985. In 1993 another line was routed from the Sleipner field to carry condensate, and the plant was extended accordingly. Today heavy additional supply- and export lines are under construction, and the plant is extended more than ever. The main role of the factory is to separate the raw gas into commercial products and to pump or ship it to the markets. The site covers a large number of well-known mechanical equipment. This presentation deals with piping, mechanical and structural disciplines. The lifetime of mechanical equipment is often difficult to predict as it depends on many factors, and the subject is complex. Mechanical equipment has been kept in-house, which provides detailed knowledge of the stages from a new to a 14 years old plant. The production regularity has always been very high, as required. The standard of the equipment is well kept, support systems are efficient, and human improvisation is extremely valuable.

Emergency operation determination system

International Nuclear Information System (INIS)

Miki, Tetsushi.

1993-01-01

The system of the present invention can determine an emergency operation coping with abnormal events occurring during nuclear plant operation without replying on an operator's judgement. That is, the system of the present invention comprises an intelligence base which divides and classifies the aims of the plant operation for the function, structure and operation manual and puts them into network. Degree of attainment for the extend of the status normality is determined on every aim of operation based on various kinds of measured data during plant operation. For a degree of attainment within a predetermined range, it is judged that an emergency operation is possible although this is in an abnormal state. Degree of emergency is determined by a fuzzy theory based on the degree of attainment, variation coefficient for the degree of attainment and the sensitivity to external disturbance as parameters. Priority for the degree of emergency on every operation aims is determined by comparison. Normality is successively checked for the determined operation aims. As a result, equipments as objects of abnormality suppressing operation are specified, and the operation amount of the equipments as objects are determined so that the measuring data are within a predetermined range. (I.S.)

The state of emergency medicine in the United Republic of Tanzania

Directory of Open Access Journals (Sweden)

B.A. Nicks

2012-09-01

Currently at most hospitals, emergency patients are cared for in Emergency Centres (ECs staffed with rotating personnel who are neither trained nor equipped to provide complete resuscitative care, but dedicated emergency care training projects are emerging. The first Emergency Medicine residency in the country was initiated in 2010 and will produce its first graduates in 2013. In 2011, a dedicated Emergency Nursing curriculum was introduced, and the Emergency Medical Association of Tanzania (EMAT, the first Emergency Medicine professional society in the country, was formed and ratified by the Ministry of Health. EMAT has been given a mandate to develop feasible initiatives for the dissemination of emergency care training to district and sub-district facilities. However, significant gaps exist in the capacity for emergency medical care including deficits in human resources, essential equipment and infrastructure – concurrent issues that EMAT must address within its development strategy.

30 CFR 75.523-3 - Automatic emergency-parking brakes.

Science.gov (United States)

2010-07-01

... immediately by the emergency deenergization device required by 30 CFR 75.523-1 and -75.523-2; (2) Engage automatically within 5.0 seconds when the equipment is deenergized; (3) Safely bring the equipment when fully...

An on-line monitoring system for navigation equipment

Science.gov (United States)

Wang, Bo; Yang, Ping; Liu, Jing; Yang, Zhengbo; Liang, Fei

2017-10-01

Civil air navigation equipment is the most important infrastructure of Civil Aviation, which is closely related to flight safety. In addition to regular flight inspection, navigation equipment's patrol measuring, maintenance measuring, running measuring under special weather conditions are the important means of ensuring aviation flight safety. According to the safety maintenance requirements of Civil Aviation Air Traffic Control navigation equipment, this paper developed one on-line monitoring system with independent intellectual property rights for navigation equipment, the system breakthroughs the key technologies of measuring navigation equipment on-line including Instrument Landing System (ILS) and VHF Omni-directional Range (VOR), which also meets the requirements of navigation equipment ground measurement set by the ICAO DOC 8071, it provides technical means of the ground on-line measurement for navigation equipment, improves the safety of navigation equipment operation, and reduces the impact of measuring navigation equipment on airport operation.

Application of electron beam equipment based on a plasma cathode gun in additive technology

Science.gov (United States)

Galchenko, N. K.; Kolesnikova, K. A.; Semenov, G. V.; Rau, A. G.; Raskoshniy, S. Y.; Bezzubko, A. V.; Dampilon, B. V.; Sorokova, S. N.

2016-11-01

The paper discusses the application of electron beam equipment based on a plasma cathode gun for three-dimensional surface modification of metals and alloys. The effect of substrate surface preparation on the adhesion strength of gas thermal coatings has been investigated.

Use of individual protection equipment and collective in case of accident during the transport of radioactive product - class 7

International Nuclear Information System (INIS)

Pastura, Valeria da F. e S.; Carvalho, Natanael Bruno de

2013-01-01

The personal protective equipment (PPE) are devices used by professionals against potential radiological hazards that may threaten the health or safety in the event of an accident or incident during the transport of radioactive material. The collective protection equipment (CPE) devices are used in place of the accident in order to protect people and the environment from risks such as safety signs, among others. This work will be part of the new edition of the NBR 9735 - Set of equipment for emergencies in land transport of dangerous goods - edited by the Brazilian Association of Technical Standards ABNT - National Standardization Forum which CNEN participates in the Study Committee - CB16 namely, dangerous, accounting for Class 7 radioactive materials. The Standard 9735 establishes the minimum set of equipment for emergencies in Inland transport of dangerous goods, consisting of protective equipment to be used by the driver and staff involved (if any) in the transport operations of transport units, equipment for signaling, isolation of the area of occurrence (fault, accident and/or emergency). Thus, we will present a set of individual and collective equipment that must accompany the carriage of Class 7 products to meet the radiological accident situations and also establish a training base for the driver as the use of them. (author)

Radiation emergency preparedness in nuclear power plants

International Nuclear Information System (INIS)

Geetha, P.V.; Ramamirtham, B.; Khot, P.

2008-01-01

The purpose of planning for radiation emergency response is to ensure adequate preparedness for protection of the plant personnel and members of the public from significant radiation exposures in the unlikely event of an accident. With a number of safety features in the reactor design and sound operating procedures, the probability of a major accident resulting in the releases of large quantities of radioactivity is extremely small. However, as an abundant cautious approach a comprehensive radiation emergency response preparedness is in place in all the nuclear power plants (NPPs). Radiation Emergency in NPPs is broadly categorized into three types; plant emergency, site emergency and off-site emergency. During off site emergency conditions, based on levels of radiation in the environment, Civil Authorities may impose several counter measures such as sheltering, administering prophylaxis (stable iodine for thyroid blocking) and evacuation of people from the affected area. Environmental Survey Laboratory (ESL) carries out environmental survey extensively in the affected sector identified by the meteorological survey laboratory. To handle emergency situations, Emergency Control Centre with all communication facility and Emergency Equipment Centre having radiation measuring instruments and protective equipment are functional at all NPPs. AERB stipulates certain periodicity for conducting the exercises on plant, site and off site emergency. These exercises are conducted and deficiencies corrected for strengthening the emergency preparedness system. In the case of off site emergency exercise, observers are invited from AERB and Crisis Management Group of Department of Atomic Energy (DAE). The emergency exercises conducted by Nuclear Power Plant Sites have been very satisfactory. (author)

Automated Announcements of Approaching Emergency Vehicles

Science.gov (United States)

Bachelder, Aaron; Foster, Conrad

2006-01-01

Street intersections that are equipped with traffic lights would also be equipped with means for generating audible announcements of approaching emergency vehicles, according to a proposal. The means to generate the announcements would be implemented in the intersection- based subsystems of emergency traffic-light-preemption systems like those described in the two immediately preceding articles and in "Systems Would Preempt Traffic Lights for Emergency Vehicles" (NPO-30573), NASA Tech Briefs, Vol. 28, No. 10 (October 2004), page 36. Preempting traffic lights is not, by itself, sufficient to warn pedestrians at affected intersections that emergency vehicles are approaching. Automated visual displays that warn of approaching emergency vehicles can be helpful as a supplement to preemption of traffic lights, but experience teaches that for a variety of reasons, pedestrians often do not see such displays. Moreover, in noisy and crowded urban settings, the lights and sirens on emergency vehicles are often not noticed until a few seconds before the vehicles arrive. According to the proposal, the traffic-light preemption subsystem at each intersection would generate an audible announcement for example, emergency vehicle approaching, please clear intersection whenever a preemption was triggered. The subsystem would estimate the time of arrival of an approaching emergency vehicle by use of vehicle identity, position, and time data from one or more sources that could include units connected to traffic loops and/or transponders connected to diagnostic and navigation systems in participating emergency vehicles. The intersection-based subsystem would then start the announcement far enough in advance to enable pedestrians to leave the roadway before any emergency vehicles arrive.

Safety technology: Emergency equipment and sea rescue techniques

Energy Technology Data Exchange (ETDEWEB)

1986-06-01

In June 1986, a two day workshop was convened to review mobile offshore drilling unit (MODU) evacuation research and development (R D) requirements for programs currently sponsored by the Marine Engineering Committee for PERD (Panel on Energy Research and Development) task 6.2. The proceedings of the workshop are presented in terms of: evacuation technology needs; a review of current R D projects for their relevance to the technological needs; recommended changes to current projects where warranted; and recommended priority R D projects that are not presently being undertaken to meet the evacuation technology needs. Current R D projects reviewed include: preferred orientation and displacement (PROD) lifeboat launching, personal transfer baskets, arctic escape system (AES), fast rescue craft (FRC), helicopter survival suits, diving bell emergency heaters, working immersion suits, diving bell emergency ascent system, undersea robotics systems and DCIEM decompression tables. It was concluded that gaps in offshore safety/evacuation capability cannot be adequately addressed by one or two major projects. Rather, a wider range of problems exist that require attention through a greater financial commitment than is presently the case. Government-industry cooperation in this field is required. Overall, the projects were judged to have been well planned, managed, and relevant to offshore safety needs. The only exception was a feeling that diving related projects consummed a disproportionate share of the available funding. Further, there was some reservation that the robotics study was outside the 6.2 PERD R D mandate. A list of recommendations is presented. 1 tab.

Emergency management and the nuclear terrorism threat

International Nuclear Information System (INIS)

DeVito, D.A.; Suiter, L.

1987-01-01

Counterterrorism is not the province of the emergency manager. Generally law enforcement has that role. Instead, the emergency manager's role is crisis management; the responsibility is to be the focal point for the chief executive officer (mayor, governor, or national executive) regarding the protection of the population. Managers must be able to gather and synthesize sufficient information, rapidly and accurately, on which to base sound decisions. To do so, they must have a highly efficient, coordinated emergency management organization in place at the state and local levels of government, and there must be a workable plan for emergency operations that integrates all public safety forces into an effective response to all types of emergencies. A major goal of emergency management is to ensure that government is in control and that the public perceives that the system is working. All states have an emergency management organization at the state level, as do most counties and large cities. However, some states and local governments, particularly those that have nuclear power plants within their borders, are better staffed, equipped, and trained than others to deal with nuclear incidents. States with nuclear facilities have an emergency management organization, an emergency plan, and adequate communications, equipment, and trained personnel to handle a nuclear accident or incident at a plant. 21 references

Evaluation of the composition of filters additional of equipment radiological intraoral by energy dispersive x-ray fluorescence (EDXRF)

International Nuclear Information System (INIS)

Franca, Alana Caroline; Torres, Catarina A.M.P.; Rocha, Ana S.S.; Deniak, Valeriy; Lara, Alessandro L.; Paschuk, Sergei A.; Fernandes, Angela; Westphalen, Fernando Henrique

2013-01-01

The need for high quality standards for radiographic images in order to make a diagnosis assertive, and being the additional filtration required in the intraoral X-ray equipment show the need of evaluating these filters. This study aims to examine the influence of the elemental composition of the filters of X-ray of dental intraoral equipment in the radiographic images quality. The filters analysis were performed by using the energy dispersive X-ray fluorescence method (EDXRF). Ten conventional filters were analysed. In this study, 33 radiographic exposures were performed using films: twenty radiographs in the incisor region and ten in the molar region, three exposures were also made in the same regions with same conditions without using filter. After radiographs development, optical density was measure and all radiographs were submitted to subjective evaluation by dental radiologists. Data obtained were correlated to effects evaluation of the elemental composition of all filters in the quality of the radiographic images. The elements found were: aluminum, cobalt, copper, sulfur, iron, manganese, titanium, zinc, and zirconium. The images obtained were identified in groups: Molars to 0.3 s; Incisors to 0.2 s; Incisors to 0.3 s, and for the group without filters. From the results obtained it was concluded that both unclear radiographs and ideal radiographs were produced by using filters of elementary common. Therefore, conventional filters evaluated were an acceptable option to produce quality images in dental radiology, despite differences in the composition of the alloys. (author)

Evaluation of the composition of filters additional of equipment radiological intraoral by energy dispersive x-ray fluorescence (EDXRF)

Energy Technology Data Exchange (ETDEWEB)

Franca, Alana Caroline; Torres, Catarina A.M.P.; Rocha, Ana S.S.; Deniak, Valeriy; Lara, Alessandro L.; Paschuk, Sergei A., E-mail: alanacarolinef@gmail.com, E-mail: sergei@utfpr.edu.br [Universidade Tecnologica Federal do Parana (CPGEI/UTFPR), Curitiba, PR (Brazil). Programa de Pos-Graduacao em Engenharia Eletrica e Informatica Industrial; Fernandes, Angela; Westphalen, Fernando Henrique, E-mail: angelafernandes@ufpr.br [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil). Setor de Ciencias da Saude

2013-07-01

The need for high quality standards for radiographic images in order to make a diagnosis assertive, and being the additional filtration required in the intraoral X-ray equipment show the need of evaluating these filters. This study aims to examine the influence of the elemental composition of the filters of X-ray of dental intraoral equipment in the radiographic images quality. The filters analysis were performed by using the energy dispersive X-ray fluorescence method (EDXRF). Ten conventional filters were analysed. In this study, 33 radiographic exposures were performed using films: twenty radiographs in the incisor region and ten in the molar region, three exposures were also made in the same regions with same conditions without using filter. After radiographs development, optical density was measure and all radiographs were submitted to subjective evaluation by dental radiologists. Data obtained were correlated to effects evaluation of the elemental composition of all filters in the quality of the radiographic images. The elements found were: aluminum, cobalt, copper, sulfur, iron, manganese, titanium, zinc, and zirconium. The images obtained were identified in groups: Molars to 0.3 s; Incisors to 0.2 s; Incisors to 0.3 s, and for the group without filters. From the results obtained it was concluded that both unclear radiographs and ideal radiographs were produced by using filters of elementary common. Therefore, conventional filters evaluated were an acceptable option to produce quality images in dental radiology, despite differences in the composition of the alloys. (author)

44 CFR 206.6 - Donation or loan of Federal equipment and supplies.

Science.gov (United States)

2010-10-01

... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Donation or loan of Federal... Donation or loan of Federal equipment and supplies. (a) In any major disaster or emergency, the... governments for use and distribution by them for the purposes of the Stafford Act. (b) A donation or loan may...

On-site emergency planning

International Nuclear Information System (INIS)

Kueffer, K.

1980-01-01

This lecture covers the Emergency Planning of the Operating organization and is based on the Code of Practice and Safety Guides of the IAEA as well as on arrangements in use at the Swiss Nuclear Power Station Beznau and - outlines the basis and content of an emergency plan - describes the emergencies postulated for emergency planning purposes - describes the responsibilities, the organization and the procedures of the operating organization to cope with emergency situations and the liaison between the operating organization, the regulatory body and public authorities - describes the facilities and equipment which should be available to cope with emergency sitauations - describes the measures and actions to be taken when an emergency arises in order to correct abnormal plant conditions and to protect the persons on-and off-site - describes the aid to be given to affected personnel - describes the aspects relevant to maintaining the emergency plan and organization in operational readiness. (orig./RW)

Lessons learned in testing of Safeguards equipment

International Nuclear Information System (INIS)

Pepper, Susan; Farnitano, Michael; Carelli, Joseph

2001-01-01

Upgrade Travel Funding' - This subtask provides funding for the upgrade of DIS equipment installed in the field; E.125.3, 'DIS Radiation Field Characterization' - This subtask provides for the procurement by the IAEA of radiation measurement equipment and technical assistance for the characterization of radiation conditions in the locations where DIS will be installed. This will help the IAEA ensure that the design specifications for the equipment are consistent with the location where the instrument will be used; E.125.4, 'DIS Design Limit Testing and Advise to Strengthen IAEA's Current Equipment Qualification Criteria' - Under this subtask, Wyle Laboratories and Quanterion Solutions will conduct SDIS design limit testing, including harsh environmental testing and accelerated aging, to determine the expected lifetime and produce a design limit report to include maximum operating environment vs. design limit analysis. Additionally, this task will include the development of a strengthened environmental qualification test plan and reliability and maintainability definition methodology for all safeguards equipment. The implementation of new equipment by the Department of Safeguards is costly. Expected costs associated with the implementation of equipment include capital costs, training and in some cases travel. The cost is dramatically increased when operational issues arise due to the costs of studying the issues, modifying and upgrading the equipment and additional travel. The U.S. Support Program believes that the IAEA's Division of Safeguards Technical Support (SGTS) must strengthen its equipment-testing program to ensure that the equipment it approves for inspection use is reliable and will not place additional burden on the Department of Safeguards' maintenance and inspection staff. The U.S. Support Program recognizes that SGTS already requires a series of fundamentally important and revealing tests, but we believe that additional tests should be added to the testing

Origins of eponymous orthopaedic equipment.

Science.gov (United States)

Meals, Clifton; Wang, Jeffrey

2010-06-01

Orthopaedists make great use of eponymous equipment, however the origins of these tools are unknown to many users. This history enriches, enlightens, and enhances surgical education, and may inspire modern innovation. We explored the origins of common and eponymous orthopaedic equipment. We selected pieces of equipment named for their inventors and in the broadest use by modern orthopaedists. We do not describe specialized orthopaedic implants and instruments owing to the overwhelming number of these devices. The history of this equipment reflects the coevolution of orthopaedics and battlefield medicine. Additionally, these stories evidence the primacy of elegant design and suggest that innovation is often a process of revision and refinement rather than sudden inspiration. Their history exposes surgical innovators as brilliant, lucky, hardworking, and sometimes odd. These stories amuse, enlighten, and may inspire modern orthopaedists to develop creative solutions of their own. The rich history of the field's eponymous instruments informs an ongoing tradition of innovation in orthopaedics.

Feasibility study for a computerized emergency preparedness simulation facility

International Nuclear Information System (INIS)

Gerhardstein, L.H.; Schroeder, J.O.; Sandusky, W.F.

1979-11-01

This report details the feasibility of a computerized Emergency Preparedness Simulation Facility (EPSF) for use by the Nuclear Regulatory Commission (NRC). The proposed facility would be designed to provide the NRC and other federal, state, and local government agencies with a capability to formulate, test, and evaluate the Emergency Preparedness Plans (EPP) which local and state agencies have/will establish for use during nuclear emergencies. In cases of any state emergency (including a nuclear emergency), high level state government officials will direct emergency procedures and insure that state and local emergency teams carry out tasks which have been established in their EPP. When an emergency exists, rapid mobilization of emergency teams, efficient communication, and effective coordination of individual team efforts is essential to safety, preservation of property, and overall public welfare. Current EPP evaluation procedures are qualitative in nature and while they do compare emergency drill performance with the EPP, the nature of the drills often does not provide enough realism to actual emergency conditions. Automated simulation of real emergency conditions using modern computer equipment and programming techniques will provide the NRC emergency evaluation teams a simulated environment which closely approximates conditions which would actually exist during a real emergency. In addition, the computer can be used to collect and log performance and event data which will aid the evaluation team in making assessments of the state or local area's EPP and their Emergency Preparedness Teams performance during emergency drills. Overall, a computerized EPSF can improve drill testing and evaluation efficiency, provide approximate emergency condition realism, and improve public awareness of local emergency procedures

Preventive Rad/Nuc Detection Equipment Categorization for Consequence Management

Energy Technology Data Exchange (ETDEWEB)

Buddemeier, B. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Musolino, S. V. [Brookhaven National Lab. (BNL), Upton, NY (United States); Klemic, G. [US Dept. of Homeland Security National Security Technology Lab., New York, NY (United States)

2017-06-01

The overall objective of this project is to research, evaluate, and test first responder preventive radiological/nuclear detection equipment (PRND) to provide state and local agencies with guidance on how to best use this equipment for response after a radiological/nuclear release or detonation. While the equipment being tested in this effort has been specifically designed for detection and interdiction operations, the fleet of PRND equipment can help fill critical needs for radiological instrumentation should a consequence management response take place. This effort will provide scientific guidance on the best way to deploy and operate this class of equipment for consequence management missions. With the support of the US Department of Homeland Security’s (DHS) Domestic Nuclear Detection Office (DNDO), PRND equipment has been placed into service at federal, state, and local agencies throughout the nation. If the equipment capability and limitations are taken into account, this large inventory can be repurposed to support the emergency response in the aftermath of a radiological of nuclear event. This report evaluates PRND equipment to define key categories of equipment and the types of missions they can be used for. This is important because there are over 100 different types of PRND equipment, often with significantly different capabilities with respect to the consequence management mission. The current DNDO draft NIMS PRND equipment types were used as a foundation and expanded, when necessary, to address key characteristics important for the consequence mission. Table 1 provides a summary of the PRND instrument categories developed for this effort. Also included on the table are some common response mission detection equipment categories that will be used for capability comparisons.

Constructing a User Interface for Cellular Phones Using Equipment and its Relations

Directory of Open Access Journals (Sweden)

Misayo Kitamura

2003-04-01

Full Text Available In a domain of SCADA (Supervisory Control And Data Acquisition systems, it is necessary to obtain information about plants such as water plants in remote places using a cellular phone in order to ascertain plant status in case of emergency.T o utilize the small screen of a cellular phone and to eliminate the engineering cost of creating de.nition data to show plant status, a method of constructing user interface using equipment in the plant and its relations is proposed. In this method, some equipment is selected from all supervised equipment using the relations between the equipment, and then the content to be displayed is generated dynamically using the selected equipment. The equipment in plants is organized as a graph structure, which involves the equipment and the relations between the equipment.T he relations adopted in this method are both the physical connections between the equipment and the conceptual relationships.The result of the selection depends on the relations and their parameter values called the context dependent weight, which changes dynamically by viewpoints.

Energy efficiency standards for residential and commercial equipment: Additional opportunities

Energy Technology Data Exchange (ETDEWEB)

Rosenquist, Greg; McNeil, Michael; Iyer, Maithili; Meyers, Steve; McMahon, Jim

2004-08-02

Energy efficiency standards set minimum levels of energy efficiency that must be met by new products. Depending on the dynamics of the market and the level of the standard, the effect on the market for a given product may be small, moderate, or large. Energy efficiency standards address a number of market failures that exist in the buildings sector. Decisions about efficiency levels often are made by people who will not be responsible for the energy bill, such as landlords or developers of commercial buildings. Many buildings are occupied for their entire lives by very temporary owners or renters, each unwilling to make long-term investments that would mostly reward subsequent users. And sometimes what looks like apathy about efficiency merely reflects inadequate information or time invested to evaluate it. In addition to these sector-specific market failures, energy efficiency standards address the endemic failure of energy prices to incorporate externalities. In the U.S., energy efficiency standards for consumer products were first implemented in California in 1977. National standards became effective starting in 1988. By the end of 2001, national standards were in effect for over a dozen residential appliances, as well as for a number of commercial sector products. Updated standards will take effect in the next few years for several products. Outside the U.S., over 30 countries have adopted minimum energy performance standards. Technologies and markets are dynamic, and additional opportunities to improve energy efficiency exist. There are two main avenues for extending energy efficiency standards. One is upgrading standards that already exist for specific products. The other is adopting standards for products that are not covered by existing standards. In the absence of new and upgraded energy efficiency standards, it is likely that many new products will enter the stock with lower levels of energy efficiency than would otherwise be the case. Once in the stock

The Effectiveness of Ultrasonography in Detecting Emergent Pediatric Pathologies and Requirement for Additional Imaging Techniques: A Retrospective Study

Directory of Open Access Journals (Sweden)

Betül Tiryaki Baştuğ

2018-04-01

Full Text Available Introduction: In emergency cases, ultrasonography is used in guiding resuscitation, to provide procedural guidance, and confirm a clinical diagnosis. In addition, it may prevent unnecessary exposure of the patient to ionizing radiation and risks caused by transporting the patient away from monitoring. This paper aimed to evaluate the effectiveness of ultrasonography in detecting emergent pediatric pathologies in a state hospital radiology unit, and to identify whether additional imaging techniques, such as computed tomography, were required. Methods: This study was designed as a retrospective investigation. A group of 536 patients were randomly selected from 1.401 pediatric patients who underwent ultrasonography for non-traumatic emergent pathologies between 2015 and 2016. Results: Of the 536 patients, 46 were diagnosed with appendicitis, 14 with pathologies of the urinary system, 1 with ileus, 29 with mesenteric lymphadenitis, 4 with intussusception, 3 with ovarian cyst rupture, 1 with ovarian torsion, and 32 with scrotal pathologies. Computed tomography was performed for 20 patients. Ureteral calculi and appendicitis were confirmed by computed tomography in 5 and 14 patients, respectively, after being identified as secondary findings by ultrasonography. In 1 patient, ileus was verified by computed tomography. The sensitivity of ultrasonography was determined to be 85.7%. Only 14% of patients were not given definite pathological diagnoses by ultrasonography alone. Subsequent computed tomography for verifying secondary findings detected by ultrasonography was essential in only 20 patients. Conclusion: Our results promote the use of ultrasonography as the initial imaging test for evaluating pediatric patients with suspected emergency pathologies.

Selection of equipment for equipment qualification

International Nuclear Information System (INIS)

Torr, K.G.

1989-01-01

This report describes the methodology applied in selecting equipment in the special safety systems for equipment qualification in the CANDU 600 MW nuclear generating stations at Gentilly 2 and Point Lepreau. Included is an explanation of the selection procedure adopted and the rationale behind the criteria used in identifying the equipment. The equipment items on the list have been grouped into three priority categories as a planning aid to AECB staff for a review of the qualification status of the special safety systems

Assessing the capacity of the healthcare system to use additional mechanical ventilators during a large-scale public health emergency (PHE)

Science.gov (United States)

Ajao, Adebola; Nystrom, Scott V.; Koonin, Lisa M.; Patel, Anita; Howell, David R.; Baccam, Prasith; Lant, Tim; Malatino, Eileen; Chamberlin, Margaret; Meltzer, Martin I.

2015-01-01

A large-scale Public Health Emergency (PHE), like a severe influenza pandemic can generate large numbers of critically ill patients in a short time. We modeled the number of mechanical ventilators that could be used in addition to the number of hospital-based ventilators currently in use. We identified key components of the healthcare system needed to deliver ventilation therapy, quantified the maximum number of additional ventilators that each key component could support at various capacity levels (i.e. conventional, contingency and crisis) and determined the constraining key component at each capacity level. Our study results showed that U.S. hospitals could absorb between 26,200 and 56,300 additional ventilators at the peak of a national influenza pandemic outbreak with robust pre-pandemic planning. This methodology could be adapted by emergency planners to determine stockpiling goals for critical resources or identify alternatives to manage overwhelming critical care need. PMID:26450633

Development of electric discharge equipment for small specimen sampling

International Nuclear Information System (INIS)

Okamoto, Koji; Kitagawa, Hideaki; Kusumoto, Junichi; Kanaya, Akihiro; Kobayashi, Toshimi

2009-01-01

We have developed the on-site electric discharge sampling equipment that can effectively take samples such as small specimens from the surface portion of the plant components. Compared with the conventional sampling equipment, our sampling equipment can take samples that are thinner in depth and larger in area. In addition, the affection to the equipment can be held down to the minimum, and the thermally-affected zone of the material due to electric discharge is small, which is to be ignored. Therefore, our equipment is excellent in taking samples for various tests such as residual life evaluation.

49 CFR 393.43 - Breakaway and emergency braking.

Science.gov (United States)

2010-10-01

... ACCESSORIES NECESSARY FOR SAFE OPERATION Brakes § 393.43 Breakaway and emergency braking. (a) Towing vehicle protection system. Every motor vehicle, if used to tow a trailer equipped with brakes, shall be equipped with... brake systems installed on towed vehicles shall be so designed, by the use of “no-bleed-back” relay...

Analysis on functions of mobile nuclear emergency monitoring lab

International Nuclear Information System (INIS)

Lai Yongfang; Wang Yonghong; Gao Jing; Sun Jian

2012-01-01

According to the fundamental purpose and mission of nuclear emergency monitoring and based on technological aspects, this paper discusses and analyses the functions and basic requirements on equipment in mobile radiation measurement lab in nuclear emergency response. (authors)

Department of Energy Emergency Management Functional Requirements Study

International Nuclear Information System (INIS)

1987-05-01

This Study, the Emergency Management Functional Requirements Study (EMFRS), identifies the physical environment, information resources, and equipment required in the DOE Headquarters Emergency Operations Center (EOC) to support the DOE staff in managing an emergency. It is the first step toward converting the present Forrestal EOC into a practical facility that will function well in each of the highly diverse types of emergencies in which the Department could be involved. 2 figs

Academic versus Non-Academic Emerging Adult College Student Technology Use

Science.gov (United States)

Swanson, Joan Ann; Walker, Erica

2015-01-01

Emerging adult college students have developmental and educational needs which are unique to their phase of life. Emerging adults are also increasingly identified by their technology use and practices. Collegiate instructors will be better equipped for educating these individuals when armed with insights concerning emerging adults' technology…

7 CFR 3015.172 - Federal share of real property, equipment, and supplies.

Science.gov (United States)

2010-01-01

... equipment. To calculate the Federal share of replacement equipment the following procedures shall be...: Determine the percentage of the replacement equipment's costs that was covered by the amount received for... the step 2 percentage. (4) Step 4: If an additional outlay for the replacement equipment was charged...

Optical system for UV-laser technological equipment

Science.gov (United States)

Fedosov, Yuri V.; Romanova, Galina E.; Afanasev, Maxim Ya.

2017-09-01

Recently there has been an intensive development of intelligent industrial equipment that is highly automated and can be rapidly adjusted for certain details. This equipment can be robotics systems, automatic wrappers and markers, CNC machines and 3D printers. The work equipment considered is the system for selective curing of photopolymers using a UV-laser and UV-radiation in such equipment that leads to additional technical difficulties. In many cases for transporting the radiation from the laser to the point processed, a multi-mirror system is used: however, such systems are usually difficult to adjust. Additionally, such multi-mirror systems are usually used as a part of the equipment for laser cutting of metals using high-power IR-lasers. For the UV-lasers, using many mirrors leads to crucial radiation losses because of many reflections. Therefore, during the development of the optical system for technological equipment using UV-laser we need to solve two main problems: to transfer the radiation for the working point with minimum losses and to include the system for controlling/handling the radiation spot position. We introduce a system for working with UV-lasers with 450mW of power and a wavelength of 0.45 μm based on a fiber system. In our modelling and design, we achieve spot sizes of about 300 μm, and the designed optical and mechanical systems (prototypes) were manufactured and assembled. In this paper, we present the layout of the technological unit, the results of the theoretical modelling of some parts of the system and some experimental results.

78 FR 31769 - Accessible Emergency Information; Apparatus Requirements for Emergency Information and Video...

Science.gov (United States)

2013-05-24

... and equipment and better access video programming.'' \\7\\ \\7\\ H.R. Rep. No. 111-563, 111th Cong., 2d... Video Accessibility Act of 2010 (``CVAA''), the Commission adopts rules requiring video programming distributors and video programming providers (including program owners) to make televised emergency information...

The state of emergency obstetric care services in Nairobi informal settlements and environs: Results from a maternity health facility survey

Directory of Open Access Journals (Sweden)

Saliku Teresa

2009-03-01

Full Text Available Abstract Background Maternal mortality in Sub-Saharan Africa remains a challenge with estimates exceeding 1,000 maternal deaths per 100,000 live births in some countries. Successful prevention of maternal deaths hinges on adequate and quality emergency obstetric care. In addition to skilled personnel, there is need for a supportive environment in terms of essential drugs and supplies, equipment, and a referral system. Many household surveys report a reasonably high proportion of women delivering in health facilities. However, the quality and adequacy of facilities and personnel are often not assessed. The three delay model; 1 delay in making the decision to seek care; 2 delay in reaching an appropriate obstetric facility; and 3 delay in receiving appropriate care once at the facility guided this project. This paper examines aspects of the third delay by assessing quality of emergency obstetric care in terms of staffing, skills equipment and supplies. Methods We used data from a survey of 25 maternity health facilities within or near two slums in Nairobi that were mentioned by women in a household survey as places that they delivered. Ethical clearance was obtained from the Kenya Medical Research Institute. Permission was also sought from the Ministry of Health and the Medical Officer of Health. Data collection included interviews with the staff in-charge of maternity wards using structured questionnaires. We collected information on staffing levels, obstetric procedures performed, availability of equipment and supplies, referral system and health management information system. Results Out of the 25 health facilities, only two met the criteria for comprehensive emergency obstetric care (both located outside the two slums while the others provided less than basic emergency obstetric care. Lack of obstetric skills, equipment, and supplies hamper many facilities from providing lifesaving emergency obstetric procedures. Accurate estimation of burden

Strategy for conformity of non-standard cryogenic equipment

CERN Multimedia

CERN. Geneva

2016-01-01

CERN as an intergovernmental organization establishes its own Safety Rules as necessary for its proper functioning. In particular, the CERN General Safety Instruction for cryogenic equipment requires that cryogenic pressure equipment at CERN shall comply with the European Pressure Equipment Directive (PED). However, due to the particular features of some of the cryogenic equipment required for the accelerators, as well as the existence of international collaborations with in-kind contributions from non-EU countries, full compliance with the PED may not always be achieved. This situation is foreseen in the Safety Rules, where CERN HSE will define the Safety requirements applicable to such equipment as well as any eventual additional compensatory measure as to ensure a commensurate level of Safety for our pressure equipment. Where compliance with PED may not be achieved, CERN HSE will become the de facto Notified Body and therefore be in charge of the assessment of the conformity of the equipment to the applica...

Phosphine Exposure Among Emergency Responders - Amarillo, Texas, January 2017.

Science.gov (United States)

Hall, Emily M; Patel, Ketki; Victory, Kerton R; Calvert, Geoffrey M; Nogueira, Leticia M; Bojes, Heidi K

2018-04-06

Phosphine is a highly toxic gas that forms when aluminum phosphide, a restricted-use pesticide* typically used in agricultural settings, reacts with water. Acute exposure can lead to a wide range of respiratory, cardiovascular, and gastrointestinal symptoms, and can be fatal (1). On January 2, 2017, the Texas Department of State Health Services (DSHS) was notified by the Texas Panhandle Poison Center of an acute phosphine exposure incident in Amarillo, Texas. DSHS investigated potential occupational phosphine exposures among the 51 on-scene emergency responders; 40 (78.4%) did not use respiratory protection during response operations. Fifteen (37.5%) of these 40 responders received medical care for symptoms or as a precaution after the incident, and seven (17.5%) reported new or worsening symptoms consistent with phosphine exposure within 24 hours of the incident. Emergency response organizations should ensure that appropriate personal protective equipment (PPE) is used during all incidents when an unknown hazardous substance is suspected. Additional evaluation is needed to identify targeted interventions that increase emergency responder PPE use during this type of incident.

40 CFR 267.34 - When must personnel have access to communication equipment or an alarm system?

Science.gov (United States)

2010-07-01

... to an internal alarm or emergency communication device, either directly or through visual or voice... communication equipment or an alarm system? 267.34 Section 267.34 Protection of Environment ENVIRONMENTAL... have access to communication equipment or an alarm system? (a) Whenever hazardous waste is being poured...

Emergency preparedness

CERN Document Server

Cennini, E; Oortman Gerlings, P

2009-01-01

On September 19th 2008, a technical fault was at the centre of a sequence of events which hampered the performance of certain equipments of the LHC 3-4 sector. Once the first effects of this sequence of events were detected, the behaviour of the CERN staff confronted to this complex and critical situation became the centre of the risk control process. During such a downward spiral the preparation of all stakeholders is essential and should respect the (apparently) basic principles of emergency preparedness. Preparedness towards normal operation of CERN facilities towards minor up to major emergency situations will be presented. The main technical, organisational and legal frameworks of the CERN emergency preparedness will be recalled, highlighting the CERN risk management and risk control strategy. Then, the sequence of events experienced by different stakeholders on September 19th will be reported, thus starting the learned lessons process.

Protocol for the Control of Emergencies with Dangerous Materials

International Nuclear Information System (INIS)

Rodriguez Acosta, F.

2000-01-01

This document is required to serve as a guide for plant engineers, in charge of the security and industrial hygiene or those people that for its work, have relationship with the use, storage and distribution of chemical substances, which represent a diversity of risks as the toxicity, the inflammability and the risk of explosion. The information that the specific protocol contains is precise and a series of sections that summarize the general information of the substance are developed, like its use, the risk of explosion, the inflammability and the physical-chemical properties. Additionally, some sections are included like the answer mechanisms before the fire presence, the personnel's decontamination and of the equipment, the gathering of the waste and the procedures of first aids. The chemical substances that cause bigger quantity of events for dangerous materials in Costa Rica are the acids, the bases, the chlorine, the liquate petroleum gas (LPG), the ammonia and the agro-chemicals. Due to the intrinsic risk that it possesses these substances, a protocol to act efficiently in front of an emergency related with some of the substances are developed. Due to the increment in the incidence of events with dangerous materials in different population's sectors, for example spills in the roads, emergencies in industries and educational centers, a law with the purpose of stopping the use and the indiscriminate manipulation of these substances in non-capable locations is necessary. Additionally, it is necessary the upgrade in the equipment and in the containers that don't fulfill the minimum requirements of security, as well as to offer the maximum security to people that have contact with such chemical substances. (Author) [es

Framework for Reducing Teaching Challenges Relating to Improvisation of Science Education Equipment and Materials in Schools

Science.gov (United States)

Akuma, Fru Vitalis; Callaghan, Ronel

2016-01-01

The science education budget of many secondary schools has decreased, while shortages and environmental concerns linked to conventional Science Education Equipment and Materials (SEEMs) have emerged. Thus, in some schools, resourceful educators produce low-cost equipment from basic materials and use these so-called improvised SEEMs in practical…

Focused Cardiac Ultrasound Using a Pocket-Size Device in the Emergency Room

Directory of Open Access Journals (Sweden)

Frederico José Neves Mancuso

2014-12-01

Full Text Available Background: Cardiovascular urgencies are frequent reasons for seeking medical care. Prompt and accurate medical diagnosis is critical to reduce the morbidity and mortality of these conditions. Objective: To evaluate the use of a pocket-size echocardiography in addition to clinical history and physical exam in a tertiary medical emergency care. Methods: One hundred adult patients without known cardiac or lung diseases who sought emergency care with cardiac complaints were included. Patients with ischemic changes in the electrocardiography or fever were excluded. A focused echocardiography with GE Vscan equipment was performed after the initial evaluation in the emergency room. Cardiac chambers dimensions, left and right ventricular systolic function, intracardiac flows with color, pericardium, and aorta were evaluated. Results: The mean age was 61 ± 17 years old. The patient complaint was chest pain in 51 patients, dyspnea in 32 patients, arrhythmia to evaluate the left ventricular function in ten patients, hypotension/dizziness in five patients and edema in one patient. In 28 patients, the focused echocardiography allowed to confirm the initial diagnosis: 19 patients with heart failure, five with acute coronary syndrome, two with pulmonary embolism and two patients with cardiac tamponade. In 17 patients, the echocardiography changed the diagnosis: ten with suspicious of heart failure, two with pulmonary embolism suspicious, two with hypotension without cause, one suspicious of acute coronary syndrome, one of cardiac tamponade and one of aortic dissection. Conclusion: The focused echocardiography with pocket-size equipment in the emergency care may allow a prompt diagnosis and, consequently, an earlier initiation of the therapy.

Focused Cardiac Ultrasound Using a Pocket-Size Device in the Emergency Room

Energy Technology Data Exchange (ETDEWEB)

Mancuso, Frederico José Neves, E-mail: frederico.mancuso@grupofleury.com.br [Disciplina de Cardiologia - Escola Paulista de Medicina - Universidade Federal de São Paulo (Unifesp), São Paulo, SP (Brazil); Disciplina de Medicina de Urgência - Escola Paulista de Medicina - Universidade Federal de São Paulo (Unifesp), São Paulo, SP (Brazil); Siqueira, Vicente Nicoliello; Moisés, Valdir Ambrósio [Disciplina de Cardiologia - Escola Paulista de Medicina - Universidade Federal de São Paulo (Unifesp), São Paulo, SP (Brazil); Gois, Aécio Flavio Teixeira [Disciplina de Medicina de Urgência - Escola Paulista de Medicina - Universidade Federal de São Paulo (Unifesp), São Paulo, SP (Brazil); Paola, Angelo Amato Vincenzo de; Carvalho, Antonio Carlos Camargo; Campos, Orlando [Disciplina de Cardiologia - Escola Paulista de Medicina - Universidade Federal de São Paulo (Unifesp), São Paulo, SP (Brazil)

2014-12-15

Cardiovascular urgencies are frequent reasons for seeking medical care. Prompt and accurate medical diagnosis is critical to reduce the morbidity and mortality of these conditions. To evaluate the use of a pocket-size echocardiography in addition to clinical history and physical exam in a tertiary medical emergency care. One hundred adult patients without known cardiac or lung diseases who sought emergency care with cardiac complaints were included. Patients with ischemic changes in the electrocardiography or fever were excluded. A focused echocardiography with GE Vscan equipment was performed after the initial evaluation in the emergency room. Cardiac chambers dimensions, left and right ventricular systolic function, intracardiac flows with color, pericardium, and aorta were evaluated. The mean age was 61 ± 17 years old. The patient complaint was chest pain in 51 patients, dyspnea in 32 patients, arrhythmia to evaluate the left ventricular function in ten patients, hypotension/dizziness in five patients and edema in one patient. In 28 patients, the focused echocardiography allowed to confirm the initial diagnosis: 19 patients with heart failure, five with acute coronary syndrome, two with pulmonary embolism and two patients with cardiac tamponade. In 17 patients, the echocardiography changed the diagnosis: ten with suspicious of heart failure, two with pulmonary embolism suspicious, two with hypotension without cause, one suspicious of acute coronary syndrome, one of cardiac tamponade and one of aortic dissection. The focused echocardiography with pocket-size equipment in the emergency care may allow a prompt diagnosis and, consequently, an earlier initiation of the therapy.

Focused Cardiac Ultrasound Using a Pocket-Size Device in the Emergency Room

International Nuclear Information System (INIS)

Mancuso, Frederico José Neves; Siqueira, Vicente Nicoliello; Moisés, Valdir Ambrósio; Gois, Aécio Flavio Teixeira; Paola, Angelo Amato Vincenzo de; Carvalho, Antonio Carlos Camargo; Campos, Orlando

2014-01-01

Cardiovascular urgencies are frequent reasons for seeking medical care. Prompt and accurate medical diagnosis is critical to reduce the morbidity and mortality of these conditions. To evaluate the use of a pocket-size echocardiography in addition to clinical history and physical exam in a tertiary medical emergency care. One hundred adult patients without known cardiac or lung diseases who sought emergency care with cardiac complaints were included. Patients with ischemic changes in the electrocardiography or fever were excluded. A focused echocardiography with GE Vscan equipment was performed after the initial evaluation in the emergency room. Cardiac chambers dimensions, left and right ventricular systolic function, intracardiac flows with color, pericardium, and aorta were evaluated. The mean age was 61 ± 17 years old. The patient complaint was chest pain in 51 patients, dyspnea in 32 patients, arrhythmia to evaluate the left ventricular function in ten patients, hypotension/dizziness in five patients and edema in one patient. In 28 patients, the focused echocardiography allowed to confirm the initial diagnosis: 19 patients with heart failure, five with acute coronary syndrome, two with pulmonary embolism and two patients with cardiac tamponade. In 17 patients, the echocardiography changed the diagnosis: ten with suspicious of heart failure, two with pulmonary embolism suspicious, two with hypotension without cause, one suspicious of acute coronary syndrome, one of cardiac tamponade and one of aortic dissection. The focused echocardiography with pocket-size equipment in the emergency care may allow a prompt diagnosis and, consequently, an earlier initiation of the therapy

Development of nuclear equipment qualification technology

Energy Technology Data Exchange (ETDEWEB)

Choi, Heon O; Kim, Wu Hyun; Kim, Jin Wuk; Kim, Jeong Hyun; Lee, Jeong Kyu; Kim, Yong Han; Jeong, Hang Keun [Korea Institute of Machinery and Materials, Taejon (Korea)

1999-03-01

In order to enhance testing and evaluation technologies, which is one of the main works of the Chanwon branch of KIMM(Korea Institute of Machinery and Materials), in addition to the present work scope of the testing and evaluation in the industrial facilities such as petroleum and chemical, plants, the qualification technologies of the equipments important to safety used in the key industrial facilities such as nuclear power plants should be localized: Equipments for testing and evaluation is to be set up and the related technologies must be developed. In the first year of this study, of vibration aging qualification technologies of equipments important to safety used in nuclear power plants have been performed. (author). 27 refs., 81 figs., 17 tabs.

An H-module linear actuator for medical equipment applications

DEFF Research Database (Denmark)

Liu, Xiao; Wu, Keyuan; ye, yunyue

2012-01-01

An H-module linear actuator (HMLA) is proposed in this paper for medical equipment applications. Compared to the existing linear actuators used in medical equipment, the proposed H-module linear actuator has much lower normal force, which makes use of an additional air-suspension system unnecessary...

Essentials for emergency care: Lessons from an inventory assessment of an emergency centre in Sub-Saharan Africa

Directory of Open Access Journals (Sweden)

Kofi Marfo Osei

2014-12-01

Conclusion: Beyond pointing out specific material resource deficiencies at the Surgical Medical Emergency (SME centre, our inventory assessment indicated a need to develop better implementation strategies for infection control policies, to collaborate with other departments on coordination of patient care, and to set a research agenda to develop emergency and acute care protocols that are both effective and sustainable in our setting. Equipment and supplies are essential elements of emergency preparedness that must be both available and ‘ready-to-hand’. Consequently, key factors in determining readiness to provide quality emergency care include supply-chain, healthcare financing, functionality of systems, and a coordinated institutional vision. Lessons learnt may be useful for others facing similar challenges to emergency medicine development.

Proceedings of the 11. annual mining industry learning seminar : 2006 equipment evolutions

Energy Technology Data Exchange (ETDEWEB)

Joseph, T. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering] (comp.)

2006-07-01

This seminar provided a forum for mine engineers, geologists, operators, vendors and academics to discuss various topics on equipment evolution that address mining industry concerns. Participants included those who are involved in mine planning, equipment selection, operations and maintenance. The presentations identified possible solutions to ongoing issues and alternative technologies emerging in the mining industry. Operators and original equipment manufacturers shared their innovations in novel developments and presented solutions to issues relevant to mining processes including truck and shovel technology issues such as tires, lube and fuel emissions. The seminar featured 17 presentations, of which 5 have been catalogued separately for inclusion in this database. tabs., figs.

Abstract: Creation and Implementation of an Emergency Trolley in ...

African Journals Online (AJOL)

This meant including both emergency and every day materials such as gloves because it is difficult to quickly obtain all equipment in emergency situations. Consulting pharmacy to discuss availability and appropriateness (for example, not including intubation medications because they require specific training) of materials ...

Modernisation of Radiation Monitoring Room as a Part of Slovenian Emergency Response Centre

International Nuclear Information System (INIS)

Sarvari, A.; Mitic, D.

2003-01-01

In the year 2002 the Slovenian Nuclear Safety Administration (SNSA) moved to the new premises therefore it had to rearrange some of its rooms for the emergency situation. SNSA does not operate with a dedicated Emergency Response Centre (ERC), instead of it the SNSA has to rearrange the existing rooms in case of an emergency. Modernisation of the equipment, with the help of government of the United Kingdom of Great Britain and Northern Ireland, for the emergency situation was carried out, especially in the monitoring room. The radiation monitoring system, which is placed in the monitoring room, continuously collects, processes and archives the incoming data of exposure to radiation and meteorological parameters on the Slovenian territory (A model national emergency response plan for radiological accidents, IAEA, Vienna, 1993. IAEA-TECDOC-718). In the emergency situation the monitoring room transforms into the room for the Dose Assessment Group (DAG), which is part of ERC (IAEA emergency response network, IAEA, Vienna, 2000, EPR-ERNET (2000)). The modernisation of monitoring room and within the DAG room with new equipment and its purpose is described in this article. Modernisation of the monitoring room and the room for DAG showed to be inevitably needed. Modernisation of the monitoring room has brought the SNSA a sophisticated and reliable system of controlling the external exposure to radiation on the Slovenian territory. The equipment, especially the equipment for the use in the emergency situation, brought novelties for the Dose Assessment Group. The group has now better and easier control of radiation situation in case of an accident. In overall this modernisation has put the Slovenian Nuclear Safety Administration a step forward in having a dedicated Emergency Response Centre, since it does not need to rearrange the room for the Dose Assessment Group. (author)

30 CFR 77.516 - Electric wiring and equipment; installation and maintenance.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Electric wiring and equipment; installation and... OF UNDERGROUND COAL MINES Electrical Equipment-General § 77.516 Electric wiring and equipment; installation and maintenance. In addition to the requirements of §§ 77.503 and 77.506, all wiring and...

Dynamic monitoring equipment for earthworks and sub grades

International Nuclear Information System (INIS)

Alvarez de Sotomayor, R.

2013-01-01

This paper take into account some dynamic auscultation equipment s that currently are available in Spain for compaction quality control on earthworks and sub grades. Closed to the equipment description, a deformation modulus calculus approximation has been developed for each of them. A standards checking has been made from national and European point of view. some important research works that have been developed in our country about dynamic monitoring equipment s for quality control in earthworks has been mentioned. In addition to this, some variables are analyzed which have an influence on deformation modulus calculi and a possibility for comparing the equipment modulus calculated with a reference laboratory test has been offered. (Author) 18 refs.

Generic procedures for monitoring in a nuclear or radiological emergency

International Nuclear Information System (INIS)

2005-03-01

This book is a Japanese version of the International Atomic Energy Agency (IAEA) publication (Report No., IAEA-TECDOC-1092, published in Vienna, 1999) of the same title. The translation of the original English into Japanese was done by the Department of Dose Assessment, Research Center for Radiation Emergency Medicine, National Institute of Radiological Sciences (NIRS). Since the Department was organized in addition to the Emergency Medicine Dept. in the Center in 2003 to establish a system for rapid and accurate dose assessment at emergent radiation exposure, the translation is thus a result of the department works, and is published with permission by IAEA as one of a series of NIRS Report (NIRS-M--179) for use in the country. The book is essentially a manual for providing technical requirements and procedures for radiation monitoring, environmental sampling and laboratory analyses for a nuclear or other radiological emergency. The contents are: Introduction, Outline of monitoring, Monitoring of outdoor radiation and contamination, Outdoor sampling, Gross alpha/beta measurement, Gamma spectrometry, Activation analyses, Basic data assessment, Work-sheets, Check-list for measuring equipments, Appendices, References, and others. (S.I.)

JCE Online: Equipment Buyers Guide

Science.gov (United States)

Holmes, Jon L.

1999-01-01

The Equipment Buyers Guide was edited by Jo Rita Jordan. The new Equipment Buyers Guide, bound into the back of this issue, is also a new resource of JCE Internet. This resource provides an online source for the information contained in the printed guide. Placing this information online allows us to regularly update it and to provide live links to the suppliers' WWW sites. The organization of the online version parallels that of the print version. There is an alphabetical list of suppliers and a categorical listing. Links to these lists are provided on every page in the left-hand navigation bar. To quickly find information about a particular supplier, you click Supplier List, click the letter that begins the supplier's name, and scroll through the list to find the supplier. To find which suppliers provide a particular type of instrument or equipment, use the Categories link; click the category of the equipment you are looking for and then click the link to a supplier. You will then be taken to an alphabetical supplier listing page where you can scroll until you find the particular supplier of the item for which you are looking. Once you have found a supplier, the online Equipment Buyers Guide gives you the traditional contact information. But in addition, you also get one-click access to the WWW sites of the suppliers that have them. Depending on the site, you should be able to find information about the items that you seek and may even be able to order the items online! We think that you will find the online version of the Equipment Buyers Guide useful. To make it more useful, please send your suggestions, any errors or omissions you find, and any additional categories to the editor at jjordan@world.std.com The online Equipment Buyers Guide can be found at JCE Online at http://JChemEd.chem.wisc.edu/JCEWWW/Resources/EBG/ JCE Online in '99 JCE Online is your online source of "all things JCE". In order to provide you with an even more useful online resource, JCE

Contact Dermatitis to Personal Sporting Equipment in Youth.

Science.gov (United States)

Marzario, Barbara; Burrows, Dianne; Skotnicki, Sandy

2016-07-01

Contact dermatitis to personal sporting equipment in youth is poorly studied. To review the results of patch testing 6 youth to their sporting equipment in a dermatology general private practice from 2006 to 2011. A retrospective analysis of 6 youth aged 11 to 14 who were evaluated for chronic and persistent dermatitis occurring in relation to sports equipment was conducted. All patients were subjected to epicutaneous (patch) testing, which included some or all of the following: North American Contact Dermatitis Group (NACGD) series, textile series, rubber series, corticosteroid series, and raw material from the patients' own personal equipment. All cases had 1 or more positive patch test reactions to an allergen within the aforementioned series, and 3 subjects tested positive to their personal equipment in raw form. Allergic contact dermatitis, not irritant, was deemed the relevant cause of chronic dermatitis in 4 of the 6 patients due to positive reactions to epicutaneous tests and/or personal equipment. The utility of testing to patients' own sporting equipment was shown to be of additional value and should be considered when patch testing for contact allergy to sporting equipment. © The Author(s) 2015.

Radionuclide diagnosis of emergency states

International Nuclear Information System (INIS)

Ishmukhametov, A.I.

1985-01-01

Solution of emergency state radionuclide diagnostics from the technical point of view is provided by the application of the mobile quick-operating equipment in combination with computers, by the use of radionuclides with acceptable for emergency medicine characteristics and by development of radionuclide investigation data propcessing express-method. Medical developments include the study of acute disease and injury radioisotope semiotics, different indication diagnostic value determining, comparison of the results, obtained during radionuclide investigation, with clinicolaboratory and instrumental data, separation of methodical complex series

PROMSYS, Plant Equipment Maintenance and Inspection Scheduling

International Nuclear Information System (INIS)

Morgan, D.L.; Srite, B.E.

1986-01-01

1 - Description of problem or function: PROMSYS is a computer system designed to automate the scheduling of routine maintenance and inspection of plant equipment. This 'programmed maintenance' provides the detailed planning and accomplishment of lubrication, inspection, and similar repetitive maintenance activities which can be scheduled at specified predetermined intervals throughout the year. The equipment items included are the typical pumps, blowers, motors, compressors, automotive equipment, refrigeration units, filtering systems, machine shop equipment, cranes, elevators, motor-generator sets, and electrical switchgear found throughout industry, as well as cell ventilation, shielding, containment, and material handling equipment unique to nuclear research and development facilities. Four related programs are used to produce sorted schedule lists, delinquent work lists, and optional master lists. Five additional programs are used to create and maintain records of all scheduled and unscheduled maintenance history. 2 - Method of solution: Service specifications and frequency are established and stored. The computer program reviews schedules weekly and prints, on schedule cards, instructions for service that is due the following week. The basic output from the computer program comes in two forms: programmed-maintenance schedule cards and programmed-maintenance data sheets. The data sheets can be issued in numerical building, route, and location number sequence as equipment lists, grouped for work assigned to a particular foreman as the foreman's equipment list, or grouped by work charged to a particular work order as the work-order list. Data sheets grouped by equipment classification are called the equipment classification list

46 CFR 197.314 - First aid and treatment equipment.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false First aid and treatment equipment. 197.314 Section 197... HEALTH STANDARDS GENERAL PROVISIONS Commercial Diving Operations Equipment § 197.314 First aid and... consists of— (i) Basic first aid supplies; and (ii) Any additional supplies necessary to treat minor trauma...

Equipping tomorrow's fire manager

Science.gov (United States)

Christopher A. Dicus

2008-01-01

Fire managers are challenged with an ever-increasing array of both responsibilities and critics. As in the past, fire managers must master the elements of fire behavior and ecology using the latest technologies. In addition, today’s managers must be equipped with the skills necessary to understand and liaise with a burgeoning group of vocal stakeholders while also...

Mutual emergency assistance arrangements at the international level

International Nuclear Information System (INIS)

Swindell, G.E.; Ha Vinh Phuong

1979-01-01

All countries do not necessarily have resources in skilled manpower and equipment enabling them to deal satisfactorily with the consequences of a nuclear incident. Therefore, a mechanism whereby such countries could obtain or provide mutual emergency assistance at international level is extremely useful. This article analyses the provisions of the Nordic Mutual Emergency Assistance Agreement and the measures taken in respect of emergency assistance by international organisations such as IAEA. (NEA) [fr

Code of practice for the safe use of industrial radiography equipment (1989)

International Nuclear Information System (INIS)

1989-12-01

This code supersedes the Code of practice for the control and safe handling of sealed radioactive sources used in industrial radiography, published by the National Health and Medical Research Council (NHMRC) in 1968. It differs significantly from the former code because radiation protection practice and recommended standards have changed. The code covers the design, construction and requirements for the safe use of X-radiography equipment and gamma-radiography equipment. It provides illustrative working rules, detailed emergency procedures and comprehensive responsibilities and duties for all personnel involved in supplying and using industrial radiography equipment. The code details those equipment requirements, personnel requirements and work practices that the NHMRC considers necessary to keep exposures to ionizing radiation as low as reasonably achievable. Some equipment and facilities currently in use may not meet all of the mandatory requirements of this code. These requirements have been included in the code to encourage progress towards future compliance in the expectation that, in the interim, statutory authorities will apply them with discretion

Alternatives Generation Analysis Long Length Contaminated Equipment Removal System Storage

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

Major pieces of Characterization sampling equipment are currently stored outdoors. This includes the Long Length Contaminated Equipment receiver trailer and transportation trailer. A decision is required to determine the preferred alternative for facilities to store and maintain this equipment. The Long Length Contaminated Equipment Removal System (LLCERS) consists of many tools, mechanisms, and controllers currently stored in various locations. Much of this equipment should be protected from the elements while being stored. Some of the LLCERS equipment should be protected with some kind of roof cover. This decision analysis is to determine the best alternative for weather protection for the large equipment requiring a cover. Additional details are included in Sections 2.0 and 5.0. Key assumptions used in this analysis are detailed in Section 3.2

Principles of off-site nuclear emergency exercises

International Nuclear Information System (INIS)

Miska, H.

2011-01-01

Due to high safety standards at nuclear power plants, no experience exits with nuclear emergencies in Western Europe. Thus, emergency exercises are the only possibility to assure effective protective measures should the very unlikely severe accident occur. The main objectives of exercises are generally the check of response plans for suitability, the test of the equipment's applicability and training of personnel for the unusual task to manage a nuclear emergency. After an introduction into the different types of exercises, this contribution focuses on offsite nuclear emergency exercises, explaining frame conditions to ensure good practice and, finally, reports some experience from exercises. (orig.)

L-038: EPR-First Responders: Forces / safety equipment. Action Guides

International Nuclear Information System (INIS)

2011-01-01

This conference is about the actions carry out by the forces and the safety equipment in a radiological emergency. The security area, the victims, the hospitals, the police vehicles area, the safety cordon, the evacuation, the contamination level and the risk of life are important aspects to be considered by the first responders.

Test Procedure - pumping system for caustic addition project

International Nuclear Information System (INIS)

Leshikar, G.A.

1994-01-01

This test procedure provides the requirements for sub-system testing and integrated operational testing of the submersible mixer pump and caustic addition equipment by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E)

Benefits of Digital Equipment Generic Qualification Activities

International Nuclear Information System (INIS)

Thomas, James E.; Steiman, Samuel C.

2002-01-01

As a result of nuclear power plant instrumentation and control obsolescence issues, there have been numerous activities during recent years relating to the qualification of digital equipment. Some of these activities have been 'generic' in nature in that the qualification was not limited to plant specific applications, but was intended to cover a broad base of potential applications of the digital equipment. These generic qualifications have been funded by equipment manufacturers and by utility groups and organizations. The generic activities sponsored by the Electric Power Research Institute (EPRI) have been pilot projects for an overall generic qualification approach. The primary benefit resulting from the generic qualification work to date is that a number of digital platforms and digital devices are now available for use in various nuclear safety-related applications. Many of the tests and evaluations necessary to support plant specific applications have been completed. The amount of data and documentation that each utility must develop on a case by case basis has been significantly reduced. There are also a number of additional benefits resulting from these industry efforts. The challenges and difficulties in qualifying digital equipment for safety-related applications are now more clearly understood. EPRI has published a lessons learned document (EPRI Report 1001452, Generic Qualification of Commercial Grade Digital Devices: Lessons Learned from Initial Pilots, which covers several different qualification areas, including device selection, project planning, vendor surveys and design reviews, and electromagnetic compatibility (EMC) qualification. Application of the experience and lessons learned from the EPRI pilot activities should help reduce the effort and cost required for future qualification work. Most generic qualification activities for commercial equipment have been conducted using the approach of EPRI TR-106439, Guideline on Evaluation and Acceptance

Definition and means of maintaining the emergency notification and evacuation system portion of the Plutonium Finishing Plant safety envelope

International Nuclear Information System (INIS)

White, W.F.

1997-01-01

The Emergency Evacuation and Notification System provides information to the PFP Building Emergency Director to assist in determining appropriate emergency response, notifies personnel of the required response, and assists in their response. The report identifies the equipment in the Safety Envelope (SE) for this System and the Administrative, Maintenance, and Surveillance Procedures used to maintain the SE Equipment

Feasibility study on emergency passive habitability systems of SPWR

International Nuclear Information System (INIS)

Obata, H.; Tabata, H.; Urakami, M.; Naito, T.

2000-01-01

The major characteristic of the Simplified Pressurized Water Reactor (SPWR) is that safety systems for the emergency core cooling and the core decay heat removal functions are achieved by passive equipment. The AP600 developed in the U.S adopts passive emergency habitability system for the main control room (MCR) and the electrical equipment rooms (EER) by using the concrete of the structures as a heat sink. For the SPWR, alternative natural circulation cooling systems have been investigated: for MCR cooling, a cold water reservoir is used as heat sink; for EER cooling, outside air is instead employed. The distribution of the air-velocity and temperature in those rooms were calculated by using a three-dimensional thermal fluid analysis code. The authors verified the conceptual feasibility of these systems as the emergency passive habitability systems in the SPWR. (author)

Joint energy demand and thermal comfort optimization in photovoltaic-equipped interconnected microgrids

NARCIS (Netherlands)

Baldi, S.; Karagevrekis, A; Michailidis, IT; Kosmatopoulos, EB

2015-01-01

Electrical smart microgrids equipped with small-scale renewable-energy generation systems are emerging progressively as an alternative or an enhancement to the central electrical grid: due to the intermittent nature of the renewable energy sources, appropriate algorithms are required to integrate

Predicting emergency diesel starting performance

International Nuclear Information System (INIS)

DeBey, T.M.

1989-01-01

The US Department of Energy effort to extend the operational lives of commercial nuclear power plants has examined methods for predicting the performance of specific equipment. This effort focuses on performance prediction as a means for reducing equipment surveillance, maintenance, and outages. Realizing these goals will result in nuclear plants that are more reliable, have lower maintenance costs, and have longer lives. This paper describes a monitoring system that has been developed to predict starting performance in emergency diesels. A prototype system has been built and tested on an engine at Sandia National Laboratories. 2 refs

Radiology preparedness in ebola virus disease: guidelines and challenges for disinfection of medical imaging equipment for the protection of staff and patients.

Science.gov (United States)

Mollura, Daniel J; Palmore, Tara N; Folio, Les R; Bluemke, David A

2015-05-01

The overlap of early Ebola virus disease (EVD) symptoms (eg, fever, headache, abdominal pain, diarrhea, emesis, and fatigue) with symptoms of other more common travel-related diseases (eg, malaria, typhoid fever, pneumonia, and meningococcemia) may result in delayed diagnosis of EVD before isolation of infected patients. Radiology departments should consider policies for and approaches to decontamination of expensive and potentially easily damaged radiology equipment. In addition, the protection of radiology personnel must be considered during the work-up phase of undiagnosed EVD patients presenting to emergency departments. The purpose of this article is to consider the effect of EVD on radiology departments and imaging equipment, with particular consideration of guidelines currently available from the Centers for Disease Control and Prevention that may be applicable to radiology. (©) RSNA, 2015.

Implementation plan for HANDI 2000 TWRS master equipment list

International Nuclear Information System (INIS)

BENNION, S.I.

1999-01-01

This document presents the implementation plan for an additional deliverable of the HANDI 2000 Project. The PassPort Equipment Data module processes include those portions of the COTS PassPort system required to support tracking and management of the Master Equipment List for Lockheed Martin Hanford Company (LMHC) and custom software created to work with the COTS products

Report on the emergency response training and equipment activities through 1991 for the transportation of transuranic waste to the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

1992-04-01

The Waste Isolation Pilot Plant (WIPP) is a research and development facility with the mission of demonstrating the safe shipment, emplacement and retrieval of radioactive transuranic (TRU) wastes resulting from the defense activities and programs of the United States. It is the only long-term storage facility constructed for TRU waste. This report provides the status on the Department of Energy (DOE) efforts as of December 31, 1991, regarding emergency response training and equipment funding provided to local, state, and tribal governments for waste shipments to the WIPP. Because of a growing public awareness of transportation activities involving nuclear materials, this report has been prepared to provide a status of the DOE's activities in this regard, as well as the cooperative efforts between the DOE and state and tribal governments

After-hours Power Status of Office Equipment and Inventory of Miscellaneous Plug-load Equipment

Energy Technology Data Exchange (ETDEWEB)

Roberson, Judy A.; Webber, Carrie A.; McWhinney, Marla C.; Brown, Richard E.; Pinckard, Margaret J.; Busch, John F.

2004-01-22

This research was conducted in support of two branches of the EPA ENERGY STAR program, whose overall goal is to reduce, through voluntary market-based means, the amount of carbon dioxide emitted in the U.S. The primary objective was to collect data for the ENERGY STAR Office Equipment program on the after-hours power state of computers, monitors, printers, copiers, scanners, fax machines, and multi-function devices. We also collected data for the ENERGY STAR Commercial Buildings branch on the types and amounts of ''miscellaneous'' plug-load equipment, a significant and growing end use that is not usually accounted for by building energy managers. This data set is the first of its kind that we know of, and is an important first step in characterizing miscellaneous plug loads in commercial buildings. The main purpose of this study is to supplement and update previous data we collected on the extent to which electronic office equipment is turned off or automatically enters a low power state when not in active use. In addition, it provides data on numbers and types of office equipment, and helps identify trends in office equipment usage patterns. These data improve our estimates of typical unit energy consumption and savings for each equipment type, and enables the ENERGY STAR Office Equipment program to focus future effort on products with the highest energy savings potential. This study expands our previous sample of office buildings in California and Washington DC to include education and health care facilities, and buildings in other states. We report data from twelve commercial buildings in California, Georgia, and Pennsylvania: two health care buildings, two large offices (> 500 employees each), three medium offices (50-500 employees), four education buildings, and one ''small office'' that is actually an aggregate of five small businesses. Two buildings are in the San Francisco Bay area of California, five are in

The FIFA medical emergency bag and FIFA 11 steps to prevent sudden cardiac death: setting a global standard and promoting consistent football field emergency care.

Science.gov (United States)

Dvorak, Jiri; Kramer, Efraim B; Schmied, Christian M; Drezner, Jonathan A; Zideman, David; Patricios, Jon; Correia, Luis; Pedrinelli, André; Mandelbaum, Bert

2013-12-01

Life-threatening medical emergencies are an infrequent but regular occurrence on the football field. Proper prevention strategies, emergency medical planning and timely access to emergency equipment are required to prevent catastrophic outcomes. In a continuing commitment to player safety during football, this paper presents the FIFA Medical Emergency Bag and FIFA 11 Steps to prevent sudden cardiac death. These recommendations are intended to create a global standard for emergency preparedness and the medical response to serious or catastrophic on-field injuries in football.

Decontamination and Decommissioning Equipment Tracking System (DDETS)

International Nuclear Information System (INIS)

Cook, S.

1994-07-01

At the request of the Department of Energy (DOE)(EM-50), the Scientific Computing Unit developed a prototype system to track information and data relevant to equipment and tooling removed during decontamination and decommissioning activities. The DDETS proof-of-concept tracking system utilizes a one-dimensional (1D) and two-dimensional (2D) bar coding technology to retain and track information such as identification number, manufacturer, requisition information, and various contaminant information, etc. The information is encoded in a bar code, printed on a label and can be attached to corresponding equipment. The DDETS was developed using a proven relational database management system which allows the addition, modification, printing, and deletion of data. In addition, communication interfaces with bar code printers and bar code readers were developed. Additional features of the system include: (a) Four different reports available for the user (REAPS, transaction, and two inventory), (b) Remote automated inventory tracking capabilities, (c) Remote automated inventory tracking capability (2D bar codes allow equipment to be scanned/tracked without being linked to the DDETS database), (d) Edit, update, delete, and query capabilities, (e) On-line bar code label printing utility (data from 2D bar codes can be scanned directly into the data base simplifying data entry), and (f) Automated data backup utility. Compatibility with the Reportable Excess Automated Property System (REAPS) to upload data from DDETS is planned

The Emergency Action Plan of the Spanish Nuclear Safety Council (CSN)

International Nuclear Information System (INIS)

Calvin Cuarteto, M.; Camarma, J. R.; Martin Calvarro, J. M

2007-01-01

The Spanish Nuclear safety Council (CSN) has assigned by law among others the function to coordinate the measures of support and answer to nuclear emergency situations for all the aspects related with nuclear safety and radiological protection. Integrating and coordinating the different organisations public and private companies whose aid is necessary for the fulfilment of the functions attributed to the Regulatory Body. In order to suitable perform this function, CSN has equipped itself with an Emergency Action Plan that structures the response organization, establishes responsibility levels, incorporates basic performance procedures and includes capabilities to face the nuclear and radiological emergencies considering the external supports, resulting from the collaboration agreements with public institutions and private companies. To accomplish the above mentioned Emergency Action Plan, CSN has established and implanted a formation and training and re-training program for the organization response for emergencies and has update an operative centre (Emergency Room called Salem), equipped with infrastructures, tools and communication and operative systems that incorporate the more advanced technologies available to date. (Author)

An emergency response centre (ERC) for the preparedness and response to nuclear and radiological emergencies

International Nuclear Information System (INIS)

Pradeepkumar, K.S.; Sharma, D.N.; Abani, M.C.

2001-01-01

This paper discusses the requirement for a state of the art Emergency Response Centre (ERC) to be developed and kept in readiness for the quick response to any nuclear or radiological emergencies. For an effective response to any major nuclear emergency an ERC having the facilities of i) environmental dose rate monitoring network established using both mobile and fixed units ii) on-line meteorological data collection and information station iii) on-line computation and prediction of isodose curves in real time and iv) properly developed and tested monitoring methodologies are essential. Vehicles with on-line data transfer facility to the ERC and equipped with different type of monitoring systems can function as Mobile Monitoring Laboratories (MMLs) and can help in quick decision making even during a radiological emergency far away from the ERC. (author)

Potentially damaging failure modes of high- and medium-voltage electrical equipment

International Nuclear Information System (INIS)

Hoy, H.C.

1983-07-01

The electrical equipment failures of both nuclear and nonnuclear public utilities were reviewed. Those failures that could pose an additional problem to surrounding and connected equipment were defined. The literature was searched; utilities, repair shops, and large electrical equipment users were contacted for failure information. The data were reviewed in detail, and failure modes were determined. Sample cascade failures are discussed. The failure rate of electrical equipment in utilities is historically quite low. Nuclear plants record too few failures to be statistically valid, but failures that have been recorded show that good design usually restricts the failure to a single piece of equipment

Facilities and medical care for on-site nuclear power plant radiological emergencies

International Nuclear Information System (INIS)

Anon.

1979-01-01

The operation of a nuclear power plant introduces risks of injury or accidents that could also result in the exposure of personnel to radiation or radioactive materials. It is important in such an event to have adequate first aid and medical facilities, supplies, equipment, transportation capabilities and trained personnel available to provide necessary care. This standard provides guidance for first aid during an emergency and for initial medical care of those overexposed to penetrating radiation or contaminated with radioactive material or radionuclides. Recommendations cover facilities, supplies, equipment and the extent of care on-site, where first aid and initial care may be provided, and off-site at a local hospital, where further medical and surgical care may be provided. Additional recommendations are also provided for the transportation of patients and the training of personnel. A brief discussion of specialized care is provided in an appendix

Definition and means of maintaining the emergency notification and evacuation system portion of the plutonium finishing plant safety envelope

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

The Emergency Evacuation and Notification System provides information to the Plutonium Finishing Plant (PFP) Building Emergency Director to assist in determining appropriate emergency response, notifies personnel of the required response, and assists in their response. The report identifies the equipment in the Safety Envelope (SE) for this System and the Administrative, Maintenance, and Surveillance Procedures used to maintain the SE Equipment

Emergency control centers for nuclear power plants

International Nuclear Information System (INIS)

Anon.

1979-01-01

Guidance is provided for the development and implementation of emergency control centers for nuclear power plants, including nuclear plant control room, nuclear plant company headquarters, emergency control center, and nuclear plant alternate emergency control center. Requirements and recommendations are presented for the mission, communications, instrumentation and equipment associated with each type of control center. Decisional aids, manning requirements and resources are also given; the decision aids cover both the accident assessment and protective action areas. Both normal and alternate means of communications are considered. Off-site emergency control centers, although not covered in the strict sense by this standard, are considered in an appendix

Emergency Status Management in Energetic Field . Risk Transfer

Directory of Open Access Journals (Sweden)

Gherasim Solovestru DOMIDE

2016-12-01

Full Text Available The state of emergency in the energy sector generates technical problems such as: disruption in the operation of machinery and equipment, replacement of equipment or others needs. Besides the technical problems which appear, also intervene economic and financial issues that generate costs for the replacement of machines, equipment and installations and expenses of compensation to third parties who have suffered losses by disconnecting the power supply or lack of electricity over a longer or shorter period. Modern methods of risk management include also economic solutions. Some of these solutions will be treated in this paper.

Emergency Victim Care. A Training Manual for Emergency Medical Technicians. Module 5. CPR, Oxygen Therapy. Revised.

Science.gov (United States)

Ohio State Dept. of Education, Columbus. Div. of Vocational Education.

This student manual, the fifth in a set of 14 modules, is designed to train emergency medical technicians (EMTs) in Ohio. The module contains two sections covering the following course content; cardiopulmonary resuscitation (CPR) (including artificial ventilation, foreign body obstructions, adjunctive equipment and special techniques, artificial…

Emergency preparedness and response plan for nuclear facilities in Indonesia

International Nuclear Information System (INIS)

Nur Rahmah Hidayati; Pande Made Udiyani

2009-01-01

All nuclear facilities in Indonesia are owned and operated by the National Nuclear Energy Agency (BATAN). The programs and activities of emergency planning and preparedness in Indonesia are based on the existing nuclear facilities, i.e. research reactors, research reactor fuel fabrication plant, radioactive waste treatment installation and radioisotopes production installation. The assessment is conducted to learn of status of emergency preparedness and response plan for nuclear facilities in Indonesia and to support the preparation of future Nuclear Power Plant. The assessment is conducted by comparing the emergency preparedness and response system in Indonesia to the system in other countries such as Japan and Republic of Korea, since the countries have many Nuclear Power Plants and other nuclear facilities. As a result, emergency preparedness response plan for existing nuclear facility in Indonesia has been implemented in many activities such as environmental monitoring program, facility monitoring equipment, and the continuous exercise of emergency preparedness and response. However, the implementation need law enforcement for imposing the responsibility of the coordinators in National Emergency Preparedness Plan. It also needs some additional technical support systems which refer to the system in Japan or Republic of Korea. The systems must be completed with some real time monitors which will support the emergency preparedness and response organization. The system should be built in NPP site before the first NPP will be operated. The system should be connected to an Off Site Emergency Center under coordination of BAPETEN as the regulatory body which has responsibility to control of nuclear energy in Indonesia. (Author)

Strengths of common resources for managing emergencies in the Spanish nuclear power plants (CAE y UME)

International Nuclear Information System (INIS)

Blas, J. de

2014-01-01

Following the accident at the Fukushima-Daiichi power plants, the electrical sector of nuclear generation recognised the need to reinforce the capacities that the nuclear power plants already had and which they were developing in order to satisfy the requisites of the stress tests, with the additional support of equipment and human resources common to all of them. Thus the idea arose to create a Spanish emergency Support centre. Its scope included an intervention unit, pumping equipment and electrical generation, a centralised warehouse and transfer logistics. UNESA-UME Collaboration Protocol With the collaboration of the CSN as a mediator, the UME reached an agreement with the nuclear electrical sector (UNESA) in order to be able to increase knowledge about the Spanish nuclear power plants and establish a means of collaboration to be able to act with their own human and equipment resources at a site that might suffer an accident such as the one at the Japanese plants of Fukushima-Daiichi. (Author)

What Chernobyl has taught us about emergency planning

International Nuclear Information System (INIS)

Orchard, H.C.

1988-01-01

The author discusses the U.K. government review of existing emergency plans in the light of experience of the Chernobyl accident, together with the nuclear industry review of the causes and consequences of the accident. Aspects of emergency planning covered by this outline review include the need for information, pressures brought to bear on site emergency organisation by public and news media, evacuation, the need for national inventories of equipment, protective clothing, health physics instruments, road transport vehicles etc. (U.K.)

RESUME-95: Results of an International Field Test of Mobile Equipment for Emergency Response

DEFF Research Database (Denmark)

Hovgaard, Jens; Scott, Marian

1997-01-01

In 1995 the exercise RESUME-95 (Rapid Environmental Surveying Using Mobile Equipment) took place in Finland. Groups from 8 European countries joined the exercise. The methods used were airborne gamma-ray measurements, car-borne measurements and in situ stationary measurements. The results of the ...

DOUBLE SHELL TANK EMERGENCY PUMPING GUIDE

International Nuclear Information System (INIS)

REBERGER, D.W.

2006-01-01

This document provides preplanning necessary to expeditiously remove any waste that may leak from the primary tank to the secondary tank for Hanford's 28 DSTs. The strategy is described, applicable emergency procedures are referenced, and transfer routes and pumping equipment for each tank are identified

Mission Analysis for Using Preventive Radiological/Nuclear Detection Equipment for Consequence Management

Energy Technology Data Exchange (ETDEWEB)

Buddemeier, Brooke R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wood-Zika, Annmarie R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Haynes, Daniel [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Klemic, Gladys A. [US Dept. of Homeland Security National Urban Security Technology Lab., Manhattan, NY (United States); Musolino, Stephen V. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2017-09-01

The overall objective of this project is to research, evaluate, and test first responder preventive radiological/nuclear detection (PRND) equipment to provide state and local agencies with scientific guidance on how to effectively use this equipment for response after a radiological/nuclear release or detonation. While the equipment being tested in this effort has been specifically designed by technology manufacturers and purchased by responders for preventive detection and source interdiction operations, the fleet of PRND equipment can help fill critical needs for radiological instrumentation should a consequence management (CM) response take place, as it is currently the most widely available and fielded radiological instrumentation by state and local agencies. This effort will provide scientific guidance on the most effective way to utilize this class of equipment for consequence management missions. Gaining a better understanding of how PRND equipment can operate and perform for these missions will allow for recommendations on the tactical approach responders can use for consequence management operations. PRND equipment has been placed into service by federal, state, and local agencies throughout the nation. If the equipment capability and limitations are taken into account, this large inventory can be leveraged to support the emergency response in the aftermath of a radiological or nuclear event. With several hundred makes and models of PRND equipment, often with significantly different detection capabilities that do not align with their nominal PRND equipment type, development of a streamlined categorization scheme with respect to consequence management missions was the first step to identifying safe and effective uses of PRND equipment for radiological/nuclear incident response.

A Study on Estimating the Next Failure Time of Compressor Equipment in an Offshore Plant

Directory of Open Access Journals (Sweden)

SangJe Cho

2016-01-01

Full Text Available The offshore plant equipment usually has a long life cycle. During its O&M (Operation and Maintenance phase, since the accidental occurrence of offshore plant equipment causes catastrophic damage, it is necessary to make more efforts for managing critical offshore equipment. Nowadays, due to the emerging ICTs (Information Communication Technologies, it is possible to send health monitoring information to administrator of an offshore plant, which leads to much concern on CBM (Condition-Based Maintenance. This study introduces three approaches for predicting the next failure time of offshore plant equipment (gas compressor with case studies, which are based on finite state continuous time Markov model, linear regression method, and their hybrid model.

Integrating hospitals into community emergency preparedness planning.

Science.gov (United States)

Braun, Barbara I; Wineman, Nicole V; Finn, Nicole L; Barbera, Joseph A; Schmaltz, Stephen P; Loeb, Jerod M

2006-06-06

Strong community linkages are essential to a health care organization's overall preparedness for emergencies. To assess community emergency preparedness linkages among hospitals, public health officials, and first responders and to investigate the influence of community hazards, previous preparation for an event requiring national security oversight, and experience responding to actual disasters. With expert advice from an advisory panel, a mailed questionnaire was used to assess linkage issues related to training and drills, equipment, surveillance, laboratory testing, surge capacity, incident management, and communication. A simple random sample of 1750 U.S. medical-surgical hospitals. Of 678 hospital representatives that agreed to participate, 575 (33%) completed the questionnaire in early 2004. Respondents were hospital personnel responsible for environmental safety, emergency management, infection control, administration, emergency services, and security. Prevalence and breadth of participation in community-wide planning; examination of 17 basic elements in a weighted analysis. In a weighted analysis, most hospitals (88.2% [95% CI, 84.1% to 92.3%]) engaged in community-wide drills and exercises, and most (82.2% [CI, 77.8% to 86.5%]) conducted a collaborative threat and vulnerability analysis with community responders. Of all respondents, 57.3% (CI, 52.1% to 62.5%) reported that their community plans addressed the hospital's need for additional supplies and equipment, and 73.0% (CI, 68.1% to 77.9%) reported that decontamination capacity needs were addressed. Fewer reported a direct link to the Health Alert Network (54.4% [CI, 49.3% to 59.5%]) and around-the-clock access to a live voice from a public health department (40.0% [CI, 35.0% to 45.0%]). Performance on many of 17 basic elements was better in large and urban hospitals and was associated with a high number of perceived hazards, previous national security event preparation, and experience in actual

Generation of equipment response spectrum considering equipment-structure interaction

International Nuclear Information System (INIS)

Lee, Sang Hoon; Yoo, Kwang Hoon

2005-01-01

Floor response spectra for dynamic response of subsystem such as equipment, or piping in nuclear power plant are usually generated without considering dynamic interaction between main structure and subsystem. Since the dynamic structural response generally has the narrow-banded shapes, the resulting floor response spectra developed for various locations in the structure usually have high spectral peak amplitudes in the narrow frequency bands corresponding to the natural frequencies of the structural system. The application of such spectra for design of subsystems often leads to excessive design conservatisms, especially when the equipment frequency and structure are at resonance condition. Thus, in order to provide a rational and realistic design input for dynamic analysis and design of equipment, dynamic equipment-structure interaction (ESI) should be considered in developing equipment response spectrum which is particularly important for equipment at the resonance condition. Many analytical methods have been proposed in the past for developing equipment response spectra considering ESI. However, most of these methods have not been adapted to the practical applications because of either the complexities or the lack of rigorousness of the methods. At one hand, mass ratio among the equipment and structure was used as an important parameter to obtain equipment response spectra. Similarly, Tseng has also proposed the analytical method for developing equipment response spectra using mass ratio in the frequency domain. This method is analytically rigorous and can be easily validated. It is based on the dynamic substructuring method as applied to the dynamic soil-structure interaction (SSI) analysis, and can relatively easily be implemented for practical applications without to change the current dynamic analysis and design practice for subsystems. The equipment response spectra derived in this study are also based on Tseng's proposed method

38 CFR 17.154 - Dog-guides and equipment for blind.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dog-guides and equipment... AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.154 Dog-guides and equipment for blind... disability may be furnished a trained dog-guide. In addition, they may be furnished necessary travel expense...

Code of practice for the safe use of industrial radiography equipment (1989)

International Nuclear Information System (INIS)

1989-12-01

This code supersedes the Code of Practice for the control and safe handling of sealed radioactive sources use din industrial radiography, published by the National Health and Medical Research Council (NHMRC) in 1968. It differs significantly from the former code because radiation protection practice and recommended standards have changed. The code covers the design, construction and requirements for the safe use of X-radiography equipment and gamma-radiography equipment. It provides illustrative working rules, detailed emergency procedures and comprehensive responsibilities and duties for all personnel involved in supplying and using industrial radiography equipment. The code details those equipment requirements, personnel requirements and work practices that the NHMRC considers necessary to keep exposures to ionizing radiation as low as reasonably achievable. Some equipment and facilities currently in use may not meet all of the mandatory requirements of this code. These requirements have been included in the code to encourage progress towards future compliance in the expectation that, in the interim, statutory authorities will apply them with discretion. 9 refs., tabs., ills

9 CFR 590.502 - Equipment and utensils; PCB-containing equipment.

Science.gov (United States)

2010-01-01

... Sanitary Standards and accepted practices currently in effect for such equipment. (c) New or replacement equipment or machinery (including any replacement parts) brought onto the premises of any official plant... equipment and machinery, and any replacement parts for such equipment and machinery. Totally enclosed...

Definition and means of maintaining the emergency notification and evacuation system portion of the plutonium finishing plant safety envelope; TOPICAL

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

The Emergency Evacuation and Notification System provides information to the Plutonium Finishing Plant (PFP) Building Emergency Director to assist in determining appropriate emergency response, notifies personnel of the required response, and assists in their response. The report identifies the equipment in the Safety Envelope (SE) for this System and the Administrative, Maintenance, and Surveillance Procedures used to maintain the SE Equipment

AEA Technology, Harwell site emergency plan

International Nuclear Information System (INIS)

1993-01-01

This plan, describes the site arrangements and facilities for dealing with an emergency at Harwell. These arrangements consist of amongst other things provision of suitably qualified, experienced and trained staff to take up posts, provision of suitable facilities and equipment, arrangements to alert and protect persons on and off the site, liaison and contact arrangements with external agencies and organisations and supply of information before and during any emergency. Other organisations have their own arrangements for dealing with an emergency at AEA Technology Harwell. The arrangements for dealing with any off-site consequences are drawn together in the ''Oxfordshire County Council Essential Services Emergency Plan (Off-Site) for AEA Technology, Harwell''. Prior information for members of the public who may be affected in the event of an emergency at Harwell is issued in the form of leaflets. (author)

Equipment considerations

International Nuclear Information System (INIS)

Anon.

1992-01-01

Trace or ultratrace analyses require that the HPLC equipment used, including the detector, be optimal for such determinations. HPLC detectors are discussed at length in Chapter 4; discussion here is limited to the rest of the equipment. In general, commercial equipment is adequate for trace analysis; however, as the authors approach ultratrace analysis, it becomes very important to examine the equipment thoroughly and optimize it, where possible. For this reason they will review the equipment commonly used in HPLC and discuss the optimization steps. Detectability in HPLC is influenced by two factors (1): (a) baseline noise or other interferences that lead to errors in assigning the baseline absorbance; (b) peak width. 87 refs

Experimental flights using a small unmanned aircraft system for mapping emergent sandbars

Science.gov (United States)

Kinzel, Paul J.; Bauer, Mark A.; Feller, Mark R.; Holmquist-Johnson, Christopher; Preston, Todd

2015-01-01

The US Geological Survey and Parallel Inc. conducted experimental flights with the Tarantula Hawk (T-Hawk) unmanned aircraft system (UAS ) at the Dyer and Cottonwood Ranch properties located along reaches of the Platte River near Overton, Nebraska, in July 2013. We equipped the T-Hawk UAS platform with a consumer-grade digital camera to collect imagery of emergent sandbars in the reaches and used photogrammetric software and surveyed control points to generate orthophotographs and digital elevation models (DEMS ) of the reaches. To optimize the image alignment process, we retained and/or eliminated tie points based on their relative errors and spatial resolution, whereby minimizing the total error in the project. Additionally, we collected seven transects that traversed emergent sandbars concurrently with global positioning system location data to evaluate the accuracy of the UAS survey methodology. The root mean square errors for the elevation of emergent points along each transect across the DEMS ranged from 0.04 to 0.12 m. If adequate survey control is established, a UAS combined with photogrammetry software shows promise for accurate monitoring of emergent sandbar morphology and river management activities in short (1–2 km) river reaches.

Emerging technologies in arthroplasty: additive manufacturing.

Science.gov (United States)

Banerjee, Samik; Kulesha, Gene; Kester, Mark; Mont, Michael A

2014-06-01

Additive manufacturing is an industrial technology whereby three-dimensional visual computer models are fabricated into physical components by selectively curing, depositing, or consolidating various materials in consecutive layers. Although initially developed for production of simulated models, the technology has undergone vast improvements and is currently increasingly being used for the production of end-use components in various aerospace, automotive, and biomedical specialties. The ability of this technology to be used for the manufacture of solid-mesh-foam monolithic and coated components of complex geometries previously considered unmanufacturable has attracted the attention of implant manufacturers, bioengineers, and orthopedic surgeons. Currently, there is a paucity of reports describing this fabrication method in the orthopedic literature. Therefore, we aimed to briefly describe this technology, some of the applications in other orthopedic subspecialties, its present use in hip and knee arthroplasty, and concerns with the present form of the technology. As there are few reports of clinical trials presently available, the true benefits of this technology can only be realized when studies evaluating the clinical and radiographic outcomes of cementless implants manufactured with additive manufacturing report durable fixation, less stress shielding, and better implant survivorship. Nevertheless, the authors believe that this technology holds great promise and may potentially change the conventional methods of casting, machining, and tooling for implant manufacturing in the future. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Emergency control center of the nuclear Regulatory Authority: a national, regional and international tool to coordinate the response to radiological and nuclear emergencies

International Nuclear Information System (INIS)

Jordan, Osvaldo; Hernandez, Daniel; Telleria, Diego; Bruno, Hector; Boutet, Luis; Kunst, Juan; Sadaniowski, Ivana; Rey, Hugo

2008-01-01

Full text: In the year 1998, with the regulation of the Nuclear Law, the Nuclear Regulatory Authority (ARN) is constituted as the national coordinator of the response in case of nuclear or radiological emergencies. The ARN builds his first operative center installed in his Head quarter in Buenos Aires. Likewise, from the obligations that come with the Convention of Early Notification of a Nuclear Accident and Convention on Assistance in the Case of a Nuclear Accident or Radiological Emergency, the ARN is the National Warning Point and the National Competent Authority. Therefore, the operative capacity of the center needs to be expanded to cover not only the national territory but also its link with the region and the IAEA, as an access point to the International community, as the conventions demand. For the purpose of giving ARN capacities which reflect the state of art at the international level on Nuclear Emergency Centers and warrant that its equipment and technology will be compatible with those abroad (mainly with IAEA), the ARN made an arrangements with Department of Energy of United States, in the framework of an existing bilateral Argentine Foreign Office/US Government agreement (Joint Standing Committee on Nuclear Cooperation). This agreement allows a deep experience exchange, high level specialists support and last generation equipment access. As a result, the center of ARN can be considerate as the most advanced civil nuclear emergency center in the region. This work describes the implementation process of the emergency center and the technical features, like the physical distribution, hardware and software resources, communication equipment, Geographic Information Systems, etc. (author)

Medical Issues: Equipment

Science.gov (United States)

... Information Packets Equipment Pool Living With SMA Medical Issues Palliative Breathing Orthopedics Nutrition Equipment Daily Life At ... curesma.org > support & care > living with sma > medical issues > equipment Equipment Individuals with SMA often require a ...

Off-site emergency exercises

International Nuclear Information System (INIS)

Miska, H.

1999-01-01

Because of the rareness of nuclear emergencies, the response to such an event has to be exercised regularly. The main objectives of such exercises, examination of plans, test of equipment, and education of the personnel, will be dealt with. Different types of exercises are presented, and good practices for exercises explained. Finally, a critical assessment of exercise experience and an outlook is presented. (orig.) [de

Rural emergency medical technician pre-hospital electrocardiogram transmission.

Science.gov (United States)

Powell, A M; Halon, J M; Nelson, J

2014-01-01

Emergent care of the acute heart attack patient continues to be at the forefront of quality and cost reduction strategies throughout the healthcare industry. Although the average cardiac door-to-balloon (D2B) times have decreased substantially over the past few years, there are still vast disparities found in D2B times in populations that reside in rural areas. Such disparities are mostly related to prolonged travel time and subsequent delays in cardiac catherization lab team activation. Urban ambulance companies that are routinely staffed with paramedic level providers have been successful in the implementation of pre-hospital 12-lead electrocardiogram (ECG) protocols as a strategy to reduce D2B times. The authors sought to evaluate the evidence related to the risk and benefits associated with the replication of an ECG transmission protocol in a small rural emergency medical service. The latter is staffed with emergency medical technician-basics (EMT-B), emergency medical technician-advanced (EMT-A), and emergency medical technician-intermediate (EMT-I) level. The evidence reviewed was limited to studies with relevant data regarding the challenges and complexities of the ECG transmission process, the difficulties associated with ECG transmission in rural settings, and ECG transmission outcomes by provider level. The evidence supports additional research to further evaluate the feasibility of ECG transmission at the non-paramedic level. Multiple variables must be investigated including equipment cost, utilization, and rural transmission capabilities. Clearly, pre-hospital ECG transmission and early activation of the cardiac catheterization laboratory are critical components to successfully decreasing D2B times.

After-hours power status of office equipment and energy use of miscellaneous plug-load equipment

Energy Technology Data Exchange (ETDEWEB)

Roberson, Judy A.; Webber, Carrie A.; McWhinney, Marla C.; Brown, Richard E.; Pinckard, Marageret J.; Busch, John F.

2004-05-27

This research was conducted in support of two branches of the EPA ENERGY STAR program, whose overall goal is to reduce, through voluntary market-based means, the amount of carbon dioxide emitted in the U.S. The primary objective was to collect data for the ENERGY STAR Office Equipment program on the after-hours power state of computers, monitors, printers, copiers, scanners, fax machines, and multi-function devices. We also collected data for the ENERGY STAR Commercial Buildings branch on the types and amounts of miscellaneous plug-load equipment, a significant and growing end use that is not usually accounted for by building energy managers. For most types of miscellaneous equipment, we also estimated typical unit energy consumption in order to estimate total energy consumption of the miscellaneous devices within our sample. This data set is the first of its kind that we know of, and is an important first step in characterizing miscellaneous plug loads in commercial buildings. The main purpose of this study is to supplement and update previous data we collected on the extent to which electronic office equipment is turned off or automatically enters a low power state when not in active use. In addition, it provides data on numbers and types of office equipment, and helps identify trends in office equipment usage patterns. These data improve our estimates of typical unit energy consumption and savings for each equipment type, and enables the ENERGY STAR Office Equipment program to focus future effort on products with the highest energy savings potential. This study expands our previous sample of office buildings in California and Washington DC to include education and health care facilities, and buildings in other states. We report data from sixteen commercial buildings in California, Georgia, and Pennsylvania: four education buildings, two medical buildings, two large offices (> 500 employees each), three medium offices (50-500 employees each), and five small

The Nuclear Emergency Assistance Team, a mobile intervention facility for nuclear accidents

International Nuclear Information System (INIS)

Koelzer, W.

1975-01-01

A nuclear emergency assistance team consisting of a vehicle pool and a stock of technical equipment was set up for operation in case of major reactor accidents. The equipment is kept in 6 containers which can be shipped on trucks, by rail or by helicopter or plane. Technical equipment and tasks of each container are briefly explained. Special transport vehicles for remote handling of contaminated material are described. (ORU) [de

PSYCHOSOCIAL ASPECTS INVOLVED IN THE SERVICE OF THE EMERGENCY PATIENT VICTIM OF VIOLENCE:REPRESENTATIONS OF NURSING TEAM

Directory of Open Access Journals (Sweden)

Claudia Mara Melo Tavares

2011-11-01

Full Text Available Objetivo: Este estudo visa analisar as representações da equipe de enfermagem sobre os aspectos psicossociais envolvidos no atendimento de emergência ao paciente vítima de violência. Método: Trata-se de uma pesquisa de campo realizada com a equipe de enfermagem de uma emergência de um hospital público do Rio de Janeiro, estando baseada no Discurso do Sujeito Coletivo. Resultados: Os aspectos psicossociais emergentes do discurso dos enfermeiros sobre o atendimento de emergência ao paciente vítima de violência foram: agilidade para manutenção da vida, incômodo pela forma como a equipe de enfermagem é tratada pelo paciente e/ou acompanhantes e preocupação com a própria segurança. Conclusão: As emoções presentes nas equipes de enfermagem que atuam com pacientes vítimas de violência são silenciadas, banalizadas e muitas vezes justificada pelo ritmo acelerado de trabalho próprio do setor de emergência. Inexistem políticas institucionais ou atitudes administrativas propiciadoras de um ambiente sócio-emocional seguro para o trabalho de enfermagem. Descritores: Enfermagem em emergência, Violência, Saúde ocupacional.

The assessment of the stability of the electronics industry facility in the man-made emergencies with the use of information technology

Directory of Open Access Journals (Sweden)

Hancharyk A.V.

2016-05-01

Full Text Available The object of study is the enterprise (object of the electronics industry. By industrial object means engineering-technical complex, which includes buildings, structures, power systems, equipment, automated systems, equipment, tools, etc. By the stability of the industrial object we mean ability to produce specified types of products in required quantities in a case of variety of emergency situations, as well as the willingness to self-repairing in if the object proves in the affected area of weak or medium damages. For the stable operation of the facility, in addition to the stability of the object, the security of workers and employees must be ensured, as well as individual and collective protection equipment have to be provided. One of the important indicators for assessing the sustainability of industrial facilities in emergencies is an evaluation of the probability of occurrence of internal and external emergencies and their impact on the operability of the industrial facility. The estimation of probability of occurrence internal and external emergency situation is characterized by a measure of the risk. By the risk means a value which includes both the probability of accidents and damage from them [1]. The development of criteria for evaluating the stability of the object in the man-made disaster is often identified with the risk. The stability of the facility’s operation in the man-made disaster is estimated by the highest acceptable risk. There are the following methods for determining the risk: statistical, model, expert and sociological. Currently, the software «SKEVIA» has been developed, which allows estimating the damage caused by man-made emergencies for a particular industrial facility. Scientific novelty lies in the development of new criteria for sustainable operation of the enterprises of electronic industry. The practical significance lies in the implementation of software «SKEVIA» at the enterprises of electronic

Safe shutdown analysis for submerged equipment inside containment

International Nuclear Information System (INIS)

Song, Dong Soo; Lee, Seung Chan; Yoon, Duk Joo; Ha, Sang Jun

2017-01-01

The purpose of the paper is to analyze internal flooding effects on the submerged safety-related components inside containment building. Safe shutdown analysis has been performed based on the criteria, assumptions and guideline provided in ANSI/ANS-56.11-1988 and ANSI/ANS-58.11-1988. Flooding can be postulated from a failure of several systems located inside the containment. Loss of coolant accident (LOCA), Feed water line break (FWLB), and other pipe breaks/cracks are assumed. The worst case flooding scenario is a large break LOCA. The maximum flood level for a large break LOCA is calculated based on the combined inventory of the reactor coolant system, the three accumulators, the boron injection tank (BIT), the chemical additive tank (CAT), and the refueling water storage tank (RWST) flooding the containment. The maximum flood level that could occur from all of the water which is available in containment is 2.3 m from the base elevation. A detailed flooding analysis for the components has been performed to demonstrate that internal flooding resulting from a postulated initiating event does not cause the loss of equipment required to achieve and maintain safe shutdown of the plant, emergency core cooling capability, or equipment whose failure could result in unacceptable offsite radiological consequences. The flood height can be calculated as h = (dh/dt) x (t-t 0 ) + h 0 , where h = time dependent flood height and subscript 0 means the initial value and height slope dh/dt. In summary, the submerged components inside containment are acceptable because they complete the mission of safety injection (SI) prior to submeregency or have no safe shutdown function including containment isolation during an accident. (author)

Preparedness of the operating organization (licensee) for emergencies at nuclear power plants

International Nuclear Information System (INIS)

1982-01-01

This Guide outlines the principal elements in devising and implementing emergency plans so that actions to be taken in accordance with the plans ensure an orderly and timely decision-making process and the availability of essential personnel, equipment, supplies and services. Principal elements included in the Guide are: (1) An outline for the basis and content of emergency planning, and the activities to be covered; (2) The responsibilities and arrangements of the operating organization (licensee) in establishing and implementing the Operating Organization Emergency Plan; (3) The liaison between the operating organization (licensee), the regulatory body, and public authorities in relation to the Operating Organization Emergency Plan; (4) Detailed measures to protect persons on-site, and guidance with respect to protection of the public off-site; (5) Facilities and equipment to cope with the emergency situation; (6) Aspects relevant to maintaining the plan and the organization in operational readiness. Although this Guide does not consider emergencies related to the off-site transportation of radioactive materials or new or irradiated fuel, many of its recommendations may be useful in planning how to cope with such emergencies

Study on the offsite emergency planning against an accident in NPP

International Nuclear Information System (INIS)

Khang, Byung Oui; Lee, Goan Yup; Wu, Jong Sup; Kim, Joo Hag; Lee, Jong Tai; Lee, Jae Eun; Ahn, Chul Hyun; Ahn, Jae Hyun; Park, Dae Woo

2009-12-01

- Proposing effective local nuclear emergency preparedness system against nuclear/radiological accidents. - Proposing improved preparation/operation scheme on emergency response facilities, installations and equipment. - Establishing protection scheme on the general public against nuclear/radiological accidents. - Proposing effective preparation/operation scheme on local radioactive monitoring system. - Establishing effective training/drill scheme on the nuclear emergency preparedness. - Proposing effective technical administrative system of the local government (Busan metropolitan city)

Influence of various parameters on effectiveness of seismic base isolation of nuclear equipment

International Nuclear Information System (INIS)

Ebisawa, K.; Kameoka, H.; Takenouchi, I.; Kajiki, S.

1995-01-01

Authors developed a methodology and EBISA code for evaluating the applicability and the effectiveness of seismic base isolation of nuclear equipment. In order to investigate the influence of various parameters on the effectiveness of seismic base isolation, a sensitivity analysis was carried out for an emergency transformer with the base isolation devices. It was proved that seismic base isolation of equipment is very effective. This effectiveness can be influenced by the differences of the base isolation devices and the direction of the input seismic wave. (author). 7 refs., 3 figs., 3 tabs

Semiconductor Manufacturing equipment introduction

International Nuclear Information System (INIS)

Im, Jong Sun

2001-02-01

This book deals with semiconductor manufacturing equipment. It is comprised of nine chapters, which are manufacturing process of semiconductor device, history of semiconductor manufacturing equipment, kinds and role of semiconductor manufacturing equipment, construction and method of semiconductor manufacturing equipment, introduction of various semiconductor manufacturing equipment, spots of semiconductor manufacturing, technical elements of semiconductor manufacturing equipment, road map of technology of semiconductor manufacturing equipment and semiconductor manufacturing equipment in the 21st century.

Inventory of gate-sensing equipment at 14 U.S. Army Corps of Engineers dams in Texas

Science.gov (United States)

Harwell, Glenn R.

2005-01-01

The U.S. Army Corps of Engineers (USACE) is a worldwide organization that provides engineering services, environmental restoration, and construction support for a wide variety of civil and military projects. The primary civil mission of the USACE is developing and managing the Nation's water resources. USACE develops projects to reduce flood damage, improve navigation channels and harbors, protect wetlands, and preserve, safeguard, and enhance the environment. Additional missions of the Corps include managing federal real estate, assisting communities with emergency operations and recovery, and providing recreation opportunities.Accurate and timely information on reservoir gate openings is critical for managing flood pools, reducing flood damage downstream from reservoirs, delivering drinking-water supplies, and meeting an assortment of competing downstream water-use needs. Documentation, operation, and maintenance of gate sensors are needed so that reliable, timely information is available to USACE to make reservoir operation decisions.USACE requested that the U.S. Geological Survey (USGS) prepare an inventory and documentation of existing gate-sensing equipment at 14 reservoirs that will serve as a user’s manual for operating the equipment. The 14 reservoirs include Aquilla Lake, Bardwell Lake, Benbrook Lake, Canyon Lake, Georgetown Lake, Granger Lake, Grapevine Lake, Jim Chapman Lake, Joe Pool Lake, Lake O’ the Pines, Ray Roberts Lake, Somerville Lake, Stillhouse Hollow Lake, and Wright Patman Lake.This report presents the inventory and documentation of the existing gate-sensing equipment at the 14. The report is organized by lake; information in each lake section includes location of lake and intake structure, directions to each lake (road log), access, equipment description, operation and maintenance information, job hazard analysis, wiring diagrams, photographs, and datalogger programs. The report also includes a list of contact information for the

Consumer opinions of emergency room medical care.

Science.gov (United States)

McMillan, J R; Younger, M S; DeWine, L C

1984-12-01

If hospital management is to adapt successfully to an increasingly competitive environment, and to retain a viable emergency department, it well be necessary to objectively and accurately assess the hospital's image in the community served. Knowledge of the consumers' views is an essential input into the formulation of strategic plans. This article reports on a study in which consumer opinions on 15 dimensions of emergency room health care were obtained from 723 respondents using a mail questionnaire. Findings reveal that consumers view the emergency room as being more expensive than other health care providers. Except for being available or convenient, little or no advantage is perceived for the emergency room over the personal physician. Even though the emergency room has specialized staff and equipment, consumers do not believe patients receive better or faster treatment in an emergency room than would be obtained in a physician's office. Unless changed, these perceptions will diminish the role of the emergency room in the delivery of health care services.

Methodology development for availability improvement of standby equipment

International Nuclear Information System (INIS)

Shin, Sung Min; Jeon, In Seop; Kang, Hyun Gook

2014-01-01

The core damage frequency (CDF) of operating and constructing pressurized nuclear plants are ranging on the order of 10 -5 and 10 -6 per year. The target CDF of new NPP design has been set at 10 -7 . In this context, although various systems are currently studied, availability improvement of standby equipment will be more efficient than the additional application of safety systems. It is obvious in every aspect, such as management and cost efficiency. Here, soundness can affect equipment unavailability, and the soundness degrades because of aging. However, some studies did not consider aging when calculating the unavailability. Standby equipment can age because of two important factors: standby stress which accumulates over time, and test stress which accumulates with the number of tests (or operations). Both factors should be considered together when aging is considered. However, some studies only considered standby stress or test stress. There are some previous studies which considered both factors. Besides equipment soundness related to aging effect, some process like bypass during test also can affect equipment unavailability because the original function of equipment cannot be performed immediately during this process. However, there are seldom studies dealing with above factors as a whole problem. This study investigated a general approach to calculate the unavailability of standby equipment which considers aging caused by standby and test stresses and bypass process. Based on this general approach, we propose two maintenance strategies which aim to reduce standby equipment unavailability. In section 2, the general approach is presented. As one of the strategies, the changing test interval method (CIM) is introduced in section 3, and its effectiveness is also analyzed. The online monitoring method (OMM) is investigated in section 4 as another method to reduce equipment unavailability. In section 5, a combination of these two methods is analyzed. A general

Liderança e trabalho em equipe: um estudo de caso da equipe de enfermagem de um hospital geral de Belo Horizonte

Directory of Open Access Journals (Sweden)

Karla Rona Silva

2011-12-01

Full Text Available O trabalho em equipe é considerado um importante pressuposto para a reorganização do processo de trabalho. Essa modalidade visa uma abordagem mais integral, resolutiva e efetiva frente às atividades coletivas e interdisciplinares. Para a equipe de enfermagem este tipo de trabalho é de fundamental importância e depende de uma liderança capaz de gerenciar os conflitos e anseios que por ventura surgirem. Tal liderança, muitas vezes, eleita pelo próprio grupo, envolve a capacidade de influenciar pessoas. Assim, esse estudo tem por objetivo analisar o papel das lideranças e sua efetividade para o trabalho no interior de uma equipe assistencial de enfermagem. Os sujeitos da pesquisa em questão são quatro técnicos de enfermagem do setor de atendimento de urgência e emergência de um hospital geral de grande porte, localizado em Belo Horizonte. Uma vez que a questão da liderança apresenta-se, na maioria das vezes, de forma subjetiva, não sendo possível analisá-la em sua plenitude em questionários fechados, optou-se pela utilização da observação participante como principal ferramenta metodológica para coleta dos dados da pesquisa. Com o estudo, pode-se observar que a equipe, de uma forma geral, possui um bom entrosamento e uma postura ético-profissional pertinente ao desenvolvimento da assistência e do cuidado frente ao paciente. No entanto, a observação participante nos revelou a existência de uma liderança autoritária exercida por um dos membros da equipe. Apesar da insatisfação gerada nos demais membros da equipe, essa postura não prejudica o desenvolvimento do trabalho.

Emergency percutaneous needle decompression for tension pneumoperitoneum

Directory of Open Access Journals (Sweden)

Körner Markus

2011-05-01

Full Text Available Abstract Background Tension pneumoperitoneum as a complication of iatrogenic bowel perforation during endoscopy is a dramatic condition in which intraperitoneal air under pressure causes hemodynamic and ventilatory compromise. Like tension pneumothorax, urgent intervention is required. Immediate surgical decompression though is not always possible due to the limitations of the preclinical management and sometimes to capacity constraints of medical staff and equipment in the clinic. Methods This is a retrospective analysis of cases of pneumoperitoneum and tension pneumoperitoneum due to iatrogenic bowel perforation. All patients admitted to our surgical department between January 2005 and October 2010 were included. Tension pneumoperitoneum was diagnosed in those patients presenting signs of hemodynamic and ventilatory compromise in addition to abdominal distension. Results Between January 2005 and October 2010 eleven patients with iatrogenic bowel perforation were admitted to our surgical department. The mean time between perforation and admission was 36 ± 14 hrs (range 30 min - 130 hrs, between ER admission and begin of the operation 3 hrs and 15 min ± 47 min (range 60 min - 9 hrs. Three out of eleven patients had clinical signs of tension pneumoperitoneum. In those patients emergency percutaneous needle decompression was performed with a 16G venous catheter. This improved significantly the patients' condition (stabilization of vital signs, reducing jugular vein congestion, bridging the time to the start of the operation. Conclusions Hemodynamical and respiratory compromise in addition to abdominal distension shortly after endoscopy are strongly suggestive of tension pneumoperitoneum due to iatrogenic bowel perforation. This is a rare but life threatening condition and it can be managed in a preclinical and clinical setting with emergency percutaneous needle decompression like tension pneumothorax. Emergency percutaneous decompression is no

Safety systems I/C equipment reliability analyses of the Kozloduy NPP units 3 and 4

Energy Technology Data Exchange (ETDEWEB)

Halev, G; Christov, N [Risk Engineering Ltd., Sofia (Bulgaria)

1996-12-31

The purpose of the analysis is to assess the safety systems I/C equipment reliability. The assessment includes: quantification of the safety systems unavailability due to component failures; definition of the minimal cut sets leading to the analysed safety systems failure; quantification of the I/C equipment importance measures of the dominant contribution components. The safety systems I/C equipment reliability has been analysed using PSAPACK (a code for probabilistic safety assessment). Fault trees for the following safety systems of the Kozloduy-3 and Kozloduy-4 reactors have been constructed: neutron flow control equipment, reactor protection system, main coolant pumps, pressurizer safety valves `Sempell`, steam dump systems, spray system, low pressure injection system, emergency feeding water system, essential service water system. THree separate reports have been issued containing the performed analyses and results. 1 ref.

Revised radiation emergency procedures at Pakistan research reactor PINSTECH

International Nuclear Information System (INIS)

Orfi, S.D.; Javed, M.; Ahmad, S.; Akhtar, K.M.; Mubarak, M.A.

1984-12-01

Necessary procedures have been laid down in this report to meet the radiation emergency at Pakistan Research Reactor PINSTECH. The Nuclear Safety Committee PINSTECH (NSCP) had also recommended a number of improvements in the existing procedures. Revision of the procedures was also considered necessary to incorporate into it new radiation units/limits and new emergency equipment available. Radiation emergency preparedness programme is of continuous nature. Latest developments else-where and local experience contribute to the improvement of the existing arrangements under this programme. (A.B.)

Electrical equipment qualification

International Nuclear Information System (INIS)

Farmer, W.S.

1983-01-01

Electrical equipment qualification research programs being carried out by CEA, JAERI, and Sandia Laboratories are discussed. Objectives of the program are: (1) assessment of accident simulation methods for electrical equipment qualification testing; lower coarse (2) evaluation of equipment aging and accelerated aging methods; (3) determine radiation dose spectrum to electrical equipment and assess simulation methods for qualification; (4) identify inadequacies in electrical equipment qualification procedures and standards and potential failure modes; and (5) provide data for verifying and improving standards, rules and regulatory guides

The replacement of technically obsolete equipments

International Nuclear Information System (INIS)

Anglaret, Ph.; Patouillaud, M.

1987-01-01

The paper covers the analysis of procedures for replacement of technically obsolete but still operational equipments in use in a nuclear power plant. The Three Mile Island accident showed that operators in the control room reqire additional information at their disposal. In 1986 CGEE Alsthom received two orders for improvements to control systems, for the South African nuclear power plant Koeberg and the Dutch nuclear power plant Borssele. The new systems will provide support to normal operation and offer additional help in accident situations. 4 figs

Laboratory operation during radiation emergency

International Nuclear Information System (INIS)

Bunata, M.; Prouza, Z.; Tecl, J.

2009-01-01

During radiation emergency, a special operation mode of laboratories of the Radiation Monitoring Network (hereinafter RMN) is expected. The principal factors differing the emergency mode from the normal one are the following: - significantly higher amount of analyzed samples; - high activities of the majority of the samples; - higher risk of personal and equipment contamination; - higher working and psychological demands on laboratory staff. The assuring of the radiation protection requirements of laboratory staff has to be the primary objective, nevertheless the risk of equipment contamination and of samples cross- contamination of course have to be as well taken into consideration. The presentation describes the experience of the RMN Central Laboratory of the National Radiation Protection Institute in Prague (SURO) which was obtained during realization of field tests, in which a radioactive matter was released. These tests allow us to evaluate the source term or radioactivity dispersal balance based on various detection methods with the aim to estimate exposure of the afflicted persons. Tests provided to simulate emergency working conditions in Central Laboratory - high number of contaminated samples, which have to be analyzed in a short time (short half-time of used radionuclide 99m Tc) using sophisticated laboratory techniques (gamma spectrometers, aerosols collectors, etc.). The testing shows the availability of the SURO laboratory to work during the radiation emergency and to participate on its determination. The suitable settings and the ideal number of staff have been found. The average analysis time was approximately 1 minute per sample and the sample results were available just a few minutes after the counting. Moreover, the settings avoided any danger and kept both the crew and the samples safe and secure from contamination. (authors)

Laboratory operation during radiation emergency

International Nuclear Information System (INIS)

Bunata, M.; Tecl, J.; Prouza, Z.

2008-01-01

During radiation emergency, a special operation mode of laboratories of the Radiation Monitoring Network (hereinafter RMN) is expected. The principal factors differing the emergency mode from the normal one are the following: - significantly higher amount of analyzed samples; - high activities of the majority of the samples; - higher risk of personal and equipment contamination; - higher working and psychological demands on laboratory staff. The assuring of the radiation protection requirements of laboratory staff has to be the primary objective, nevertheless the risk of equipment contamination and of samples cross- contamination of course have to be as well taken into consideration. The presentation describes the experience of the RMN Central Laboratory of the National Radiation Protection Institute in Prague (SURO) which was obtained during realization of field tests, in which a radioactive matter was released. These tests allow us to evaluate the source term or radioactivity dispersal balance based on various detection methods with the aim to estimate exposure of the afflicted persons. Tests provided to simulate emergency working conditions in Central Laboratory -high number of contaminated samples, which have to be analyzed in a short time (short half-time of used radionuclide 99m Tc) using sophisticated laboratory techniques (gamma spectrometers, aerosols collectors, etc.). The testing shows the availability of the SURO laboratory to work during the radiation emergency and to participate on its determination. The suitable settings and the ideal number of staff have been found. The average analysis time was approximately 1 minute per sample and the sample results were available just a few minutes after the counting. Moreover, the settings avoided any danger and kept both the crew and the samples safe and secure from contamination. (authors)

Availability of Life Support Equipment and its Utilization by Ambulance Drivers.

Science.gov (United States)

Acharya, Rija; Badhu, Angur; Shah, Tara; Shrestha, Sharmila

2017-09-08

An effective ambulance is a vital requirement for providing an emergency medical service. Well-equipped ambulances with trained paramedics can save many lives during the golden hours of trauma care. The objective was to document the availability and utilization of basic life support equipment in the ambulances and to assess knowledge on first aid among the drivers. Descriptive design was used. Total of 109 ambulances linked to B.P. Koirala Institute of Health Sciences were enrolled using purposive sampling method. Self- constructed observation checklist and semi structured interview schedule was used for data collection. More than half of the respondents had less than five years of experience and were not trained in first aid. About two-third of the respondents had adequate knowledge on first aid. About 90% of the ambulance had oxygen cylinder and adult oxygen mask which was 'usually' used equipment. More than half of ambulance had equipment less than 23% as compared to that of national guidelines. There was significant association of knowledge with the experience (p = 0.004) and training (p = 0.001). Availability of equipment was associated with training received (p = 0.007),organization (p= 0.032)and district (p = 0.023) in which the ambulance is registered. The study concludes that maximum ambulance linked to BPKIHS, Nepal did not have even one fourth of the equipment for basic life support. Equipment usually used was oxygen cylinder and oxygen mask. Majority of driver had adequate knowledge on first aid and it was associated with training and experience.

Space Heating Equipment

Energy Technology Data Exchange (ETDEWEB)

Rafferty, Kevin D.

1998-01-01

The performance evaluation of space heating equipment for a geothermal application is generally considered from either of two perspectives: (a) selecting equipment for installation in new construction, or (b) evaluating the performance and retrofit requirements of an existing system. With regard to new construction, the procedure is relatively straightforward. Once the heating requirements are determined, the process need only involve the selection of appropriately sized hot water heating equipment based on the available water temperature. It is important to remember that space heating equipment for geothermal applications is the same equipment used in non-geothermal applications. What makes geothermal applications unique is that the equipment is generally applied at temperatures and flow rates that depart significantly from traditional heating system design. This chapter presents general considerations for the performance of heating equipment at non-standard temperature and flow conditions, retrofit of existing systems, and aspects of domestic hot water heating.

Universal machine ''Shtrek'' and the tractor-lifter with pneumatic-equipment control. [Auxiliary multipurpose materials handling equipment

Energy Technology Data Exchange (ETDEWEB)

Bal' bert, B M; Borumenskiy, V A; Lishenko, A P; Mitchenko, G A

1982-01-01

The machine ''Shtrek'' is described. It makes it possible to mechanize over 20 auxiliary operations: loading-unloading operations: extraction of old and deformed timbering; dissmantling of obstructions; erection of different types of timbering; making and restoring of drainage channels; laying and straightening of a drift and its leveling; assembly and disassembly of pipelines and mine equipment, etc. Depending on the type of operation, the machine has the corresponding suspended equipment. The elementary variant has a limited area of application at mines of the central region of the Dunbass. Currently a pneumatic variant of the machine ''Shtrek'' has been developed. The electric motor and the starter of the pumping equipment of the machine have been replaced by a pneumatic motor and pneumatically controlled valve KTM-50. In this case there was significant reduction in the weight of the pumping equipment and in its overall dimensions; the electric drive of the hydraulic distributors for controlling the mechanisms were replaced by simpler pneumatic ones; the logical circuit of the control system was constructed on the USEPPA elements. A specialized tractor-lifter designed for moving suspended loads is described for auxiliary operations in the near-face zone of the preparatory drifts. The machine also lifts and lowers the boom, rotates the boom by 270/sup 0/ and additionally lifts and lowers the weight-lifting hook.

The tendency of medical electrical equipment - IEC 60601-2-54: Particular requirements for the basic safety and essential performance of x-ray equipment for radiography and radioscopy

International Nuclear Information System (INIS)

Roh, Young Hoon; Kim, Jung Min

2015-01-01

Medical electrical equipment - Part 1: General requirement for basic safety and essential performance of MFDS was revised as 3th edition and Medical electrical equipment Part 2-54: Particular requirements for the basic safety and essential performance of X-ray equipment will be expected to be announced as notification. Therefore this technical report was written to introduce provision of the particular requirements, replacement, addition, amendment. The purpose of this particular requirements is to secure requirements for basic safety and essential performance of X-ray equipment for radiography and radioscopy. X-ray high voltage generator, mechanical protective device, protection against radiation is included in this particular requirements. Medical electrical equipment - Part 1, Part 1-2, Part 1-3 is applied to this particular requirements. If the requirements is announced as notification, It is expected to widen understanding for basic safety and essential performance of X-ray equipment for radiography and radioscopy and play a part to internationalize of medical equipment

The seismic assessment of wheeled vehicle type equipment (e.g. emergency power supply vehicle) against severe accident for nuclear power plant in Japan

International Nuclear Information System (INIS)

Ikeda, Takuya; Mitsuzawa, Daisuke; Yamaguchi, Yoshikazu; Hasebe, Motohiko; Imamura, Ryutaro; Tomitani, Yuji; Ueyama, Ippei; Kawamoto, Takahiro

2017-01-01

After the events at the Fukushima Dai-ichi Nuclear Power Plant, the equipment to mitigate the effects of severe accidents has been installed in the domestic nuclear power plants. From the viewpoint of convenience for installation, etc., a number of industry standard-based wheeled vehicle type equipment has been placed. On the other hand, the new regulations require the equipment for severe accidents to withstand the Design Basis Earthquake. Therefore, the seismic qualification is essential item for wheeled vehicle type equipment according to the regulatory requirement. At that time, compared to the traditional safety-related equipment, there was not enough knowledge of seismic evaluation for vehicle type equipment. This paper reports the overview of wheeled vehicle type equipment and the seismic qualification by test. (author)

Oil spill emergency response: Fulfilling regulatory requirements on the Grand Banks

International Nuclear Information System (INIS)

Horvath, C.L.

1991-01-01

Offshore well licensing under Canadian regulations requires the operator to conduct a practice exercise of oil spill countermeasures and emergency response procedures at least yearly, once the drilling program starts. The relevant parts of the Newfoundland Offshore Petroleum Drilling Regulations are summarized and the objectives and benefits of the practice exercises are reviewed. In addition to ensuring regulatory compliance, the exercises also provide the opportunity to test operational procedures, to provide in-house training, and improve response efficiency by regular repetition of the exercise. Exercises in communications during a spill incident in the offshore and in deployment of offshore spill response equipment conducted by Petro-Canada in Newfoundland are described. Problems identified during the exercises are noted

Handling of radiation emergency involving accidental detachment of 20 Ci iridium-192 source in a guide tube of a radiographic equipment in industrial radiography site

International Nuclear Information System (INIS)

Zaparde, S.P.; Murthy, B.K.S.; Vora, V.B.; Subramanian, G.

1979-01-01

The source capsule containing about 17.2 Ci of iridium-192 got accidently unscrewed in a guide tube of a gamma radiography equipment while carrying out the radiography of the spiral casing at construction site of a Hydroelectric Power Station. Immediately after the incident about 10 meter distance all around the spiral casing was cordoned off. The unscrewed capsule along with the source pellet was transferred to a lead container by raising the closed end of the guide tube of about 1/2 meters in length. The source pencil cable and cap of source capsule were separated from the source pellet. The source pellet was further shielded by a steel container and lead sheets. The source pellet was reloaded in the source capsule with limited facilities available at the work site. The source capsule cap was perfectly screwed by standing behind the L bench temporarily constructed out of lead sheets for the above jobs. During the above operation, the person received a whole body dose of 2000 mR and extrimety dose of 3000 mR. Handling of one more radiation emergency of similar type is described. A few appliances designed and fabricated for use in such emergencies are briefly described. (auth.)

EPRI spearheads generic PM recommendations for infrastructure equipment

International Nuclear Information System (INIS)

Worledge, David H.; Hinchcliffe, Glenn R.; Benak, Mark S.; Bridges, Martin

2007-01-01

All companies have at their core a vast amount of similar equipment that would benefit from solid preventive maintenance (PM) recommendations that are generic and easily adapted to meet operational conditions. The re-emergence of PM optimization methods like Reliability Centered Maintenance, further illustrates that companies in all industries recognize the positive influence that a well-focused maintenance program has on the corporate bottom line. The Electric Power Research Institute (EPRI) has long been a leader in providing universally adaptable maintenance solutions to meet the evolving needs of its membership. Nearly ten years ago, EPRI began developing the PM Basis Database, a one-of-a-kind repository of PM recommendations for basic infrastructure components (such as pumps, motors, valves, compressors), derived from equipment experts. EPRI has now made available this comprehensive body of knowledge to all industries. This paper will explore the origins and structure of the database, how these generic PM recommendations benefit every industry, and how they may be obtained. (author)

49 CFR 393.130 - What are the rules for securing heavy vehicles, equipment and machinery?

Science.gov (United States)

2010-10-01

... heavy vehicles, equipment and machinery? (a) Applicability. The rules in this section apply to the transportation of heavy vehicles, equipment and machinery which operate on wheels or tracks, such as front end... heavy vehicles, equipment or machinery with crawler tracks or wheels. (1) In addition to the...

Mutual emergency assistance for radiation accidents

International Nuclear Information System (INIS)

1971-01-01

This document presents the result of a questionnaire survey conducted in order to assess what type of emergency assistance IAEA member states could provide in the event of radiation accidents. The survey covers resources like skilled personnel in collection, analysis and interpretation of data, surveying and radiation protection equipment, radiochemical analysis facilities, and medical assistance capacities

Information on current status of equipment and activities for extension of NPP Kozloduy life time

International Nuclear Information System (INIS)

Pekov, B.

1995-01-01

The NPP Kozloduy personnel activities are described directed to undertake measures to overcome the difficulties entailed by equipment failures and human errors in order to avoid recurrent emergency events and to reduce their total numbers. 12 figs, 2 tabs

Personal messages reduce vandalism and theft of unattended scientific equipment.

Science.gov (United States)

Clarin, B-Markus; Bitzilekis, Eleftherios; Siemers, Björn M; Goerlitz, Holger R

2014-02-01

Scientific equipment, such as animal traps and autonomous data collection systems, is regularly left in the field unattended, making it an easy target for vandalism or theft. We tested the effectiveness of three label types, which differed in their information content and tone of the message, that is, personal , neutral or threatening , for reducing incidents of vandalism and theft of unattended scientific field equipment. The three label types were attached to 20 scientific equipment dummies each, which were placed semi-hidden and evenly distributed in four public parks in Munich, Germany. While the label type had no effect on the severity of the interactions with our equipment dummies, the personal label reduced the overall number of interactions by c . 40-60%, compared with the dummies showing the neutral or threatening label type. We suggest that researchers, in addition to securing their field equipment, label it with personal and polite messages that inform about the ongoing research and directly appeal to the public not to disturb the equipment. Further studies should extend these results to areas with different socio-economic structure.

Overview of Mobile Equipment Used in Case of Beyond Design Basis Accident at NPP Krsko

International Nuclear Information System (INIS)

Lukacevic, H.; Kopinc, D.; Ivanjko, M.

2016-01-01

Terrorist attack in USA in the September 11, 2001 and accident at the Fukushima - Daiichi Nuclear Power Station in the March 11, 2011 highlight the importance of mitigating strategies in responding to Beyond Design Basis Accident (BDBA), while ensuring cooling of reactor core, containment and spent fuel pool. Nuclear Power Plant Krsko (NEK) has acquired additional mobile equipment and made necessary modifications on existing systems for the connection of this equipment (fast couplers). Usage of mobile equipment is not only limited to design basis accident (DBA), but, also to prevent and mitigate the consequences in case of BDBA, when other plant systems are not available. NEK also decided to take steps for upgrade of safety measures and prepared Safety Upgrade Program (SUP), which is consistent with the nuclear industry response to the Fukushima accident and is implementing main projects and modifications related to SUP. NEK mobile equipment is not required to operate under normal reactor plant operation except for periodic surveillance testing and is incorporated into the normal training process. Equipment is dislocated from the reactor building and most of the equipment is located in the new building, able to withstand extreme natural events, including earthquakes and tornadoes. The usage of all mobile equipment is prescribed as an additional option in NEK operating procedures in following cases and enables following options: filling various tanks, filling the steam generators, filling the containment, additional compressed air source, spent fuel pool refilling and spraying, alternative power supply. This document provides an overview of NEK mobile equipment, which consists of various mobile fire protection pumps, air compressors, protective equipment, fire trucks, diesel generators. Sufficient fuel supply for the equipment is provided on site for a minimum three days of operation. (author).

Caustic addition system operability test procedure

International Nuclear Information System (INIS)

Parazin, R.E.

1994-11-01

This test procedure provides instructions for performing operational testing of the major components of the 241-AN-107 Caustic Addition System by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E)

Caustic addition system operability test procedure

Energy Technology Data Exchange (ETDEWEB)

Parazin, R.E.

1994-11-01

This test procedure provides instructions for performing operational testing of the major components of the 241-AN-107 Caustic Addition System by WHC and Kaiser personnel at the Rotating Equipment Shop run-in pit (Bldg. 272E).

LESSONS LEARNED IN TESTING OF SAFEGUARDS EQUIPMENT

International Nuclear Information System (INIS)

Pepper, S.; Farnitano, M.; Carelli, J.; Hazeltine, J.; Bailey, D.

2001-01-01

The International Atomic Energy Agency's (IAEA) Department of Safeguards uses complex instrumentation for the application of safeguards at nuclear facilities around the world. Often, this equipment is developed through cooperation with member state support programs because the Agency's requirements are unique and are not met by commercially available equipment. Before approving an instrument or system for routine inspection use, the IAEA subjects it to a series of tests designed to evaluate its reliability. In 2000, the IAEA began to observe operational failures in digital surveillance systems. In response to the observed failures, the IAEA worked with the equipment designer and manufacturer to determine the cause of failure. An action plan was developed to correct the performance issues and further test the systems to make sure that additional operational issues would not surface later. This paper addresses the steps taken to address operation issues related to digital image surveillance systems and the lessons learned during this process

Common floor system vertical earthquake-proof structure for reactor equipment

International Nuclear Information System (INIS)

Morishita, Masaki.

1996-01-01

In an LMFBR type reactor, a reactor container, a recycling pump and a heat exchanger are disposed on a common floor. Vertical earthquake-proof devices which can be stretched only in vertical direction formed by laminating large-sized bellevilles are disposed on a concrete wall at the circumference of each of reactor equipments. A common floor is placed on all of the vertical earthquake-proof devices to support the entire earthquake-proof structure simultaneously. If each of reactor equipments is loaded on the common floor and the common floor is entirely supported against earthquakes altogether, since the movement of each of the reactor equipments loaded on the common floor is identical, relative dislocation is not exerted on the main pipelines which connect the equipments. In addition, since the entire earthquake structure has a flat common floor and each of the reactor equipments is suspended to minimize the distance between a gravitational center and a support point, locking vibration is less caused to the horizontal earthquake. (N.H.)

Choice and maintenance of equipment for electron crystallography.

Science.gov (United States)

Mills, Deryck J; Vonck, Janet

2013-01-01

The choice of equipment for an electron crystallography laboratory will ultimately be determined by the available budget; nevertheless, the ideal lab will have two electron microscopes: a dedicated 300 kV cryo-EM with a field emission gun and a smaller LaB(6) machine for screening. The high-end machine should be equipped with photographic film or a very large CCD or CMOS camera for 2D crystal data collection; the screening microscope needs a mid-size CCD for rapid evaluation of crystal samples. The microscope room installations should provide adequate space and a special environment that puts no restrictions on the collection of high-resolution data. Equipment for specimen preparation includes a carbon coater, glow discharge unit, light microscope, plunge freezer, and liquid nitrogen containers and storage dewars. When photographic film is to be used, additional requirements are a film desiccator, dark room, optical diffractometer, and a film scanner. Having the electron microscopes and ancillary equipment well maintained and always in optimum condition facilitates the production of high-quality data.

Experiment and equipment of depositing diamond films with CVD system

International Nuclear Information System (INIS)

Xie Erqing; Song Chang'an

2002-01-01

CVD (chemical vapor deposition) emerged in recent years is a new technique for thin film deposition, which play a key role in development of modern physics. It is important to predominate the principle and technology of CVD for studying modern physics. In this paper, a suit of CVD experimental equipment for teaching in college physics is presented, which has simple design and low cost. The good result was gained in past teaching practices

Re-qualification of switchgear equipment following field modification

International Nuclear Information System (INIS)

Tulk, J.D.; El Bestawi, M.A.

1984-01-01

A set of 4.16 kV switchgear was seismically qualified by shaker table test for use in a nuclear power plant. Later, the equipment was modified by the addition of two extra switches and enclosures. This paper describes the methods used to extend the qualification achieved in the original proof test to the new configuration. Qualification of the modified switchgear depended on demonstrating that the intensity of the shaking that would be experienced by equipment mounted in the extended enclosure during a design basis earthquake (DBE) would be no stronger than the shaking that occurred during the original qualification testing. This was accomplished by a combination of analysis and experiment. Natural frequencies and mode-shapes of the original and extended enclosure structures were determined through in-situ modal tests on the equipment. Mathematical models based on the experimental results were then used for dynamic analyses which generated two sets of in-equipment response spectra: one set representing the original qualification test; and one set representing the response of the modified equipment to a hypothetical DBE. Qualification was confirmed by demonstrating that the test-based response spectra for the original configuration exceeded the response spectra developed for the extended structure subjected to DBE level excitation

Designing of a mobile decontamination facility (MDF) for preparedness and response to nuclear/radiological emergencies

International Nuclear Information System (INIS)

Joshi, G.H.; Garai, S.K.; Chatterjee, M.K.; Pradeepkumar, K.S.; Sharma, D.N.

2005-01-01

During a radiological emergency in public domain, likelihood of radioactive contamination cannot be completely ruled out. Timely and effective decontamination can significantly reduce possible external and internal radiation exposure to public. The objective of designing of a mobile decontamination facility is to develop the capability for decontaminating affected persons in case of any radiological emergency in public domain. A fully equipped decontamination facility on the wheels will be able to reach at the scene and will be able to decontaminate a large number of victims with the help of optimized decontamination procedures in short duration avoiding unwanted radiation exposure. This self-supporting decontamination facility is designed to be equipped with sufficient number of radiation monitoring instruments, equipments for decontamination, decontamination agents etc. (author)

76 FR 17573 - Energy Conservation Standards for Commercial Refrigeration Equipment: Public Meeting and...

Science.gov (United States)

2011-03-30

... INFORMATION: I. Statutory Authority II. History of Standards Rulemaking for Commercial Refrigeration Equipment... feedback from interested parties on its analytical framework, models, and preliminary results. II. History... equipment installed in the field, such as in grocery stores and restaurants. DOE also carries out additional...

RETRIEVAL EQUIPMENT DESCRIPTIONS

International Nuclear Information System (INIS)

J. Steinhoff

1997-01-01

The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) retrieval from the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. There are no quality assurance requirements or QA controls in this document. Retrieval under normal conditions is accomplished with the same fleet of equipment as is used for emplacement. Descriptions of equipment used for retrieval under normal conditions is found in Emplacement Equipment Descriptions, DI: BCAF00000-01717-5705-00002 (a document in progress). Equipment used for retrieval under abnormal conditions is addressed in this document and consists of the following: (1) Inclined Plane Hauler; (2) Bottom Lift Transporter; (3) Load Haul Dump (LHD) Loader; (4) Heavy Duty Forklift for Emplacement Drifts; (5) Covered Shuttle Car; (6) Multipurpose Vehicle; and (7) Scaler

[Current situation of pediatric emergency in tertiary and teaching hospitals in 15 provinces, municipalities and autonomous regions in China Mainland].

Science.gov (United States)

2014-12-01

Pre-hospital care, emergency department and critical care medicine are the key components of emergency medical service system. Two investigations about the pediatric critical care medicine in China mainland showed great progress. In recent years, most hospitals in China mainland have established emergency department, hardware configuration and staff status were gradually standardized. But most of the emergency departments mainly provide service to adult patients and pediatric emergency medicine lags behind. The purpose of this investigation was to understand the current situation and main problems of pediatric emergency in China mainland. A questionnaire developed by the Subspecialty Group of Pediatrics, Chinese Society of Emergency Medicine and the Subspecialty Group of Emergency Medicine, Chinese Society of Pediatrics was e-mailed to the members of the above-mentioned two subspecialty groups. The contents of the questionnaire included 46 items which were divided into 5 categories: the general situation of the hospital, the pediatric emergency setting and composition, key equipments and techniques, staff status, training program and running data from 2011 to 2012. Sixty-three questionnaires were delivered and 27 (42.9%) hospitals responded which located in 15 different provinces, municipalities and autonomous regions. Among the 27 hospitals, 10 (37.0%) had no pediatric resuscitation room; 25 (92.6%) had no equipments for cardiac output monitor and gastric lavage; 13 (48.1%) had no bedside fibrolaryngoscope or fiberbronchoscope; 5 (18.5%) had no blood gas analyzer; 4 (14.8%) without respirator, defibrillator, bedside radiography or ultrasonic equipment; 2 (7.4%) had no neonatal incubator; 9 (33.3%) could not do intraossous infusion. The average ratio of professional emergency pediatricians to all physicians was 43.5%. Twenty hospitals incompletely filled in the pediatric emergency running data. The main problems existing in pediatric emergency include: imperfect

Data communication equipment

International Nuclear Information System (INIS)

Kim, Hak Seon; Lee, Sang Mok

1998-02-01

The contents of this book are introduction of data communication on definition, purpose and history, information terminal about data communication system and data transmission system, data transmit equipment of summary, transmission cable, data port, concentrator and front-end processor, audio communication equipment like phones, radio communication equipment of summary on foundation of electromagnetic waves, AM transmitter, AM receiver, FM receiver and FM transmitter, a satellite and mobile communication equipment such as earth station, TT and C and Cellular phone, video telephone and new media apparatus.

Medical equipment management

CERN Document Server

Willson, Keith; Tabakov, Slavik

2013-01-01

Know What to Expect When Managing Medical Equipment and Healthcare Technology in Your Organization As medical technology in clinical care becomes more complex, clinical professionals and support staff must know how to keep patients safe and equipment working in the clinical environment. Accessible to all healthcare professionals and managers, Medical Equipment Management presents an integrated approach to managing medical equipment in healthcare organizations. The book explains the underlying principles and requirements and raises awareness of what needs to be done and what questions to ask. I

Model Design on Emergency Power Supply of Electric Vehicle

Directory of Open Access Journals (Sweden)

Yuanliang Zhao

2017-01-01

Full Text Available According to the mobile storage characteristic of electric vehicles, an emergency power supply model about the electric vehicles is presented through analyzing its storage characteristic. The model can ensure important consumer loss minimization during power failure or emergency and can make electric vehicles cost minimization about running, scheduling, and vindicating. In view of the random dispersion feature in one area, an emergency power supply scheme using the electric vehicles is designed based on the K-means algorithm. The purpose is to improve the electric vehicles initiative gathering ability and reduce the electric vehicles gathering time. The study can reduce the number of other emergency power supply equipment and improve the urban electricity reliability.

On safety 1E qualification of electrical equipment for nuclear power stations

International Nuclear Information System (INIS)

Segarceanu, D.; Geambasu, C.; Avramescu, M.

1995-01-01

Electrical equipment and systems for the emergency shutdown of a nuclear reactor are qualified according to safety class 1E. Methods of qualification meeting the requirements should be used, either individually or in combination include, type-test qualification, qualification by operating experience, qualification by analysis, combined qualification. These methods qualification principles, procedures and documents are discussed. (N.T.). 1 fig

Emergency water supply facility for nuclear reactor

International Nuclear Information System (INIS)

Karasawa, Toru

1998-01-01

Water is stored previously in an equipment storage pit disposed on an operator floor of a reactor building instead of a condensate storage vessel. Upon occurrence of an emergency, water is supplied from the equipment storage pit by way of a sucking pipeline to a pump of a high pressure reactor core water injection circuit and a pump of a reactor-isolation cooling circuit to supply water to a reactor. The equipment storage pit is arranged in a building so that the depth thereof is determined to keep the required amount of water by storing water at a level lower than the lower end of a pool gate during normal operation. Water is also supplied from the equipment storage pit by way of a supply pipeline to a spent fuel storage pool on the operation floor of the reactor building. Namely, water is supplied to the spent fuel storage pool by a pump of a fuel pool cooling and cleaning circuit. This can eliminate a suppression pool cleaning circuit. (I.N.)

Behavior of critical structures and equipment at 100-N plant during a postulated tornado

International Nuclear Information System (INIS)

Davis, H.S.

1978-01-01

The objective of this report is to document the results of an analytical study for determining the effects of tornadic wind pressures and missiles on critical structures and equipment at 100-N reactor. These particular structures and equipment are essential for maintaining the reactor in a safe, shutdown condition. The analyses show that structures, systems and components required for safe reactor shutdown and operations of the Emergency Core Cooling System (ECCS) would not be damaged by a 175 mph tornado, nor associated missiles, to the extent that the ECCS would not be able to function adequately

EVALUATION OF RESULTS OF ROAD RESEARCH OF LANOS CAR, EQUIPPED WITH AN ADVANCED HYDRAULIC BRAKE DRIVE

Directory of Open Access Journals (Sweden)

I. Nazarov

2016-12-01

Full Text Available The results of studies of road emergency braking of the car, the brake system equipped with an improved hydraulic brake actuator according to the patent number 76189 Ukraine are analyzed. This drive provides more efficient emergency braking of cars under operating conditions by of installing in each of the contours of the rear brakes one brake-power, each of which provides distribution of braking forces between the wheels of the corresponding side.

Role of first responder's training in the management of nuclear and radiological emergencies

International Nuclear Information System (INIS)

Nagarajan, V.; Sankhla, Rajesh; Verma, R.K.

2008-01-01

Consequent to the terrorist attacks on WTC in USA and other similar terrorist attacks worldwide, there has been increasing public concern regarding the use of radioactive materials in a malevolent act. As the radioactive sources are widely used in the industries, terrorists may have access to these facilities and obtain the radioactive material suitable for making Radioactive Dispersal Device (RDD) often called as dirty bomb. Response to nuclear or radiological emergency may involve highly specialized agencies or technical experts. Hence well-coordinated arrangements must be integrated with those required for any other conventional emergencies. During radiological emergencies, emergency service personnel are expected to play a major role in the early response. Though these personnel are well equipped and trained in tackling the normal emergencies it is essential to train them to deal with the radiological emergencies due to inherent characteristics of radioactivity. For the effective management of radiological emergencies, these first responders are required to be trained in such a way that they understand the concept of radiation protection. This objective can be achieved by using a typical training module consisting of interactive class room lectures, practical sessions to use the instruments and handling of radioactive sources, demonstration of radiation protection practices, exhibition of all radiation survey instruments and protective equipment etc., display of various posters and RDD Emergency Exercise. (author)

Renewal of radiological equipment.

Science.gov (United States)

2014-10-01

In this century, medical imaging is at the heart of medical practice. Besides providing fast and accurate diagnosis, advances in radiology equipment offer new and previously non-existing options for treatment guidance with quite low morbidity, resulting in the improvement of health outcomes and quality of life for the patients. Although rapid technological development created new medical imaging modalities and methods, the same progress speed resulted in accelerated technical and functional obsolescence of the same medical imaging equipment, consequently creating a need for renewal. Older equipment has a high risk of failures and breakdowns, which might cause delays in diagnosis and treatment of the patient, and safety problems both for the patient and the medical staff. The European Society of Radiology is promoting the use of up-to-date equipment, especially in the context of the EuroSafe Imaging Campaign, as the use of up-to-date equipment will improve quality and safety in medical imaging. Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or renewal. This plan should look forward a minimum of 5 years, with annual updates. Teaching points • Radiological equipment has a definite life cycle span, resulting in unavoidable breakdown and decrease or loss of image quality which renders equipment useless after a certain time period.• Equipment older than 10 years is no longer state-of-the art equipment and replacement is essential. Operating costs of older equipment will be high when compared with new equipment, and sometimes maintenance will be impossible if no spare parts are available.• Older equipment has a high risk of failure and breakdown, causing delays in diagnosis and treatment of the patient and safety problems both for the patient and the medical staff.• Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or replacement. This plan should look forward a

49 CFR 239.103 - Passenger train emergency simulations.

Science.gov (United States)

2010-10-01

... effectiveness of its plan during that major emergency and, as appropriate, modify the rescheduled simulation. (d... greater than the current reporting threshold of part 225 of this chapter to railroad on-track equipment, signals, tracks, track structures, or roadbeds, including labor costs and the costs for acquiring new...

Protecting front-line survey and rescue teams during emergencies

International Nuclear Information System (INIS)

Tresise, H.

1980-01-01

Means of protecting front-line survey and rescue teams during emergencies are described. The team composition, their apparatus, the selection of the incident control point, the use of guidelines and breathing apparatus and control point trolley and equipment are discussed. (H.K.)

Strategy for developing and conducting nuclear emergency exercises

International Nuclear Information System (INIS)

2007-01-01

Emergency situations demand that actions be taken by responsible organisations and individuals at the site of the emergency and at the local, national and international levels to mitigate the impact on people and the environment. Effective emergency response requires development and implementation of emergency plans and procedures; established arrangements at the local, national and international levels; acquisition and maintenance of resources (funding, equipment and personnel); training of personnel; conduct of exercises; and a 'feedback programme' whereby improvements to the emergency management system are made based on lessons identified from exercises and actual events. A means for demonstrating the effectiveness of an emergency programme is through the conduct of exercises. Exercises demonstrate the effectiveness of plans, procedures, training and equipment; adequacy of response arrangements and resources; capabilities of response personnel in performing their assigned tasks; ability of individuals and organisations to work together; and provide a forum for exploring and testing revisions, modifications, and new and/or proposed changes to any emergency programme element in near realistic situations. Exercises may range in scope from small-scale drills to large-scale national or international exercises. There is clear benefit to organisations in supporting, developing and conducting well-managed exercises. Exercising is a resource-intensive tool; however, it is a critical tool for enhancing performance, testing arrangements and identifying areas for improvement. A thoroughly developed strategy should therefore be in place to ensure maximum value from an exercise programme. This report contributes to the good practice and management of exercise programmes by providing a strategy for improving the value of planning, conducting, participating in and/or supporting exercises. The OECD/NEA International Nuclear Emergency Exercise (INEX) series undertaken over the

Improved Biomass Cooking Stoves and Improved Stove Emission Equipment

Energy Technology Data Exchange (ETDEWEB)

HATFIELD, MICHAEL; Still, Dean

2013-04-15

In developing countries, there is an urgent need for access to safe, efficient, and more affordable cooking technologies. Nearly 2.5 billion people currently use an open fire or traditional cookstove to prepare their meals, and recent models predict that use of biomass for cooking will continue to be the dominant energy use in rural, resource-poor households through 2030. For these families, cooking poses serious risks to health, safety, and income. An alarming 4 million people, primarily women and children, die prematurely each year from indoor and outdoor exposure to the harmful emissions released by solid fuel combustion. Use of traditional stoves can also have a significant impact on deforestation and climate change. This dire situation creates a critical need for cookstoves that significantly and verifiably reduce fuel use and emissions in order to reach protective levels for human health and the environment. Additionally, advances in the scientific equipment needed to measure and monitor stove fuel use and emissions have not kept pace with the significant need within the industry. While several testing centers in the developed world may have hundred thousand-dollar emissions testing systems, organizations in the field have had little more than a thermometer, a scale, and subjective observations to quantify the performance of stove designs. There is an urgent need for easy-to-use, inexpensive, accurate, and robust stove testing equipment for use by laboratory and field researchers around the world. ASAT and their research partner, Aprovecho Research Center (ARC), have over thirty years of experience addressing these two needs, improved cookstoves and emissions monitoring equipment, with expertise spanning the full spectrum of development from conceptual design to product manufacturing and dissemination. This includes: 1) research, design, and verification of clean biomass cookstove technology and emissions monitoring equipment; 2) mass production of quality

Equipment decontamination: A brief survey of the DOE complex

International Nuclear Information System (INIS)

Conner, C.; Chamberlain, D.B.; Chen, L.; Vandegrift, G.F.

1995-03-01

Deactivation at DOE facilities has left a tremendous amount of contaminated equipment behind. In-situ methods are needed to decontaminate the interiors of the equipment sufficiently to allow either free release or land disposal. A brief survey was completed of the DOE complex on their needs for equipment decontamination with in-situ technology to determine (1) the types of contamination problems within the DOE complex, (2) decontamination processes that are being used or are being developed within the DOE, and (3) the methods that are available to dispose of spent decontamination solutions. In addition, potential sites for testing decontamination methods were located. Based on the information obtained from these surveys, the Rocky Flats Plant and the Idaho National Engineering Laboratory appear to be best suited to complete the initial testing of the decontamination processes

Emergent Access to the Airway and Chest in American Football Players.

Science.gov (United States)

Swartz, Erik E; Mihalik, Jason P; Decoster, Laura C; Al-Darraji, Sossan; Bric, Justin

2015-07-01

American football has the highest rate of fatalities and catastrophic injuries of any US sport. The equipment designed to protect athletes from these catastrophic events challenges the ability of medical personnel to obtain neutral spine alignment and immobilization during airway and chest access for emergency life-support delivery. To compare motion, time, and difficulty during removal of American football helmets, face masks, and shoulder pads. Quasi-experimental, crossover study. Controlled laboratory. We recruited 40 athletic trainers (21 men, 19 women; age = 33.7 ± 11.2 years, height = 173.1 ± 9.2 cm, mass = 80.7 ± 17.1 kg, experience = 10.6 ± 10.4 years). Paired participants conducted 16 trials in random order for each of 4 helmet, face-mask, and shoulder-pad combinations. An 8-camera, 3-dimensional motion-capture system was used to record head motion in live models wearing properly fitted helmets and shoulder pads. Time and perceived difficulty (modified Borg CR-10). Helmet removal resulted in greater motion than face-mask removal, respectively, in the sagittal (14.88°, 95% confidence interval [CI] = 13.72°, 16.04° versus 7.04°, 95% CI = 6.20°, 7.88°; F(1,19) = 187.27, P football players must eventually be removed for imaging and medical treatment. Our results fill a gap in the evidence to support current recommendations for prehospital emergent management in patients wearing protective football equipment. Helmet face masks and shoulder pads with quick-release designs allow for clinically acceptable removal times without inducing additional motion or difficulty.

Point-of-Care Test Equipment for Flexible Laboratory Automation.

Science.gov (United States)

You, Won Suk; Park, Jae Jun; Jin, Sung Moon; Ryew, Sung Moo; Choi, Hyouk Ryeol

2014-08-01

Blood tests are some of the core clinical laboratory tests for diagnosing patients. In hospitals, an automated process called total laboratory automation, which relies on a set of sophisticated equipment, is normally adopted for blood tests. Noting that the total laboratory automation system typically requires a large footprint and significant amount of power, slim and easy-to-move blood test equipment is necessary for specific demands such as emergency departments or small-size local clinics. In this article, we present a point-of-care test system that can provide flexibility and portability with low cost. First, the system components, including a reagent tray, dispensing module, microfluidic disk rotor, and photometry scanner, and their functions are explained. Then, a scheduler algorithm to provide a point-of-care test platform with an efficient test schedule to reduce test time is introduced. Finally, the results of diagnostic tests are presented to evaluate the system. © 2014 Society for Laboratory Automation and Screening.

The Student Volunteer Army: a 'repeat emergent' emergency response organisation.

Science.gov (United States)

Carlton, Sally; Mills, Colleen E

2017-10-01

This paper seeks to contribute to understanding of the factors associated with an effective emergent emergency response organisation and to provide new insights into this understudied area. It examines, through an analysis of a range of textual resources, the emergence and re-emergence of the Student Volunteer Army (SVA) during the devastating earthquakes in Canterbury, New Zealand, in 2010-11. This evaluation is conducted in relation to the four key features of an effective emergency response organisation: adaptability; direction; leadership; and communication. In addition, the paper aims to further understanding of 'emergency entrepreneurship' and thus of the values and strategies that underpin social entrepreneur organisations in times of normalcy. The paper concludes that the unique position of the SVA as a 'repeat emergent' emergency response organisation enabled it to innovate continually and to improve repeatedly its systems, relationships, and image, such that it exhibited features common to emergent and established emergency response organisations. © 2017 The Author(s). Disasters © Overseas Development Institute, 2017.

Strategic plan for the development of IAEA safeguards equipment

International Nuclear Information System (INIS)

Khlebnikov, N.

2001-01-01

Full text: The need for a top-down Safeguards Strategy to focus departmental objectives was recognized by the Programme Performance Appraisal System (PPAS) performed on the Equipment Development Project in 1999. The Department of Safeguards prepared at the end of 2000 a 5-year Strategic Plan to identify the changes and improvements expected to take place over the 2001-2005 period. Those Strategic Objectives were supposed to be used to properly plan IAEA Safeguards activities and define appropriate and coherent R and D programmes. The present paper describes the strategic directions that the IAEA will follow in the area of equipment development in order to meet the Safeguards Department long-term objectives for 2001-2005. The paper, which is derived from the IAEA Strategic Equipment Development Plan, prepared by the Division of Technical Support, includes two parts: general principles and policies applicable to all equipment development tasks; specific strategic guidance. The paper will not describe the detailed plans which are prepared based on the strategic plan on a biannual basis. Equipment development activities have been divided in five major projects (NDA, Seals, Surveillance, Unattended Monitoring and Remote Monitoring). Strategic directions for each of these projects will be described in the paper. Separate sections will deal with equipment development strategic guidance in the area of additional protocol inspections, JNFL projects, illicit trafficking and Trilateral Initiative. (author)

Plant equipment services with laser metrology

International Nuclear Information System (INIS)

Hayes, J.H.; Kreitman, P.J.

1995-01-01

A new industrial metrology process is now being applied to support PWR Nuclear Plant Steam Generator Replacement Projects. The method uses laser tracking interferometry to perform as built surveys of existing and replacement plant equipment. This method provides precision data with a minimum of setup when compared to alternative methods available. In addition there is no post processing required to ascertain validity. The data is obtained quickly, processed in real time and displayed during the survey in the desired coordinate system. These capabilities make this method of industrial measure ideal for various data acquisition needs throughout the power industry, from internal/external equipment templating to area mapping. Laser tracking interferometry is an improvement on the present use of optical instruments and surveying technique. In order to describe the laser tracking interferometry measurement process, previous methods of templating and surveying are first reviewed

Development of Emergency Operating Strategies for Beyond Design Basis External Event(BDBEE)s in Korean WH Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Yoon, Duk-Joo; Lee, Seung-Chan; Sung, Je-Joong; Ha, Sang-Jun [KHNP CRI, Daejeon (Korea, Republic of); Hong, Soon-Joon; Hwang, Su-Hyun; Lee, Byung-Chul; Park, Kang-Min [FNC Tech. Co., Yongin (Korea, Republic of)

2015-10-15

Westinghouse developed and connected emergency operating procedures into a set of FLEX Support Guidelines(FSGs). This paper explains that Korean WH(Westinghouse) type nuclear power plants develop emergency operating strategies for ELAP(extended loss of all AC power), which include guidelines to use permanent and portable equipment as necessary to prevent core damage until AC power is restored from a reliable alternate source of AC power. The Korean emergency operating response strategies were developed to cope with a ELAP such as Fukushima event. The strategies include guidelines to prevent fuel damage using the FLEX equipment. Operators should take actions to prepare FLEX equipment within license basis SBO coping time. The loss of all AC power has been analyzed to identify the behavior of major NSSS process variables using RELAP computer code. The accident analysis showed that the plant does not result in fuel damage in 72 hours after an ELAP if operators take actions to cool RCS with opening of SG ADV in 5 gpm seal leak case. In this scenario, because ELAP is in process and all power cannot be used, operator should operate the FLEX equipment in order to actuate active equipment using the EOP fo SBO response. This strategy will prevent entering SAMG because this actions result in core cooling and stay in core exit temperature less than 650 .deg. C. Korean emergency operating guidelines(EOGs) will be developed using this strategies for response to the BDBEE.

Performance diagnostic system for emergency diesel generators

International Nuclear Information System (INIS)

Logan, K.P.

1991-01-01

Diesel generators are commonly used for emergency backup power at nuclear stations. Emergency diesel generators (EDGs) are subject to both start-up and operating failures, due to infrequent and fast-start use. EDG reliability can be critical to plant safety, particularly when station blackout occurs. This paper describes an expert diagnostic system designed to consistently evaluate the operating performance of diesel generators. The prototype system is comprised of a suite of sensor monitoring, cylinder combustion analyzing, and diagnostic workstation computers. On-demand assessments of generator and auxiliary equipment performance are provided along with color trend displays comparing measured performance to reference-normal conditions

Emergency Medical Service (EMS): Rotorcraft Technology Workshop

Science.gov (United States)

Bauchspies, J. S.; Adams, R. J.

1981-01-01

A lead organization on the national level should be designated to establish concepts, locations, and the number of shock trauma air medical services. Medical specialists desire a vehicle which incorporates advances in medical technology trends in health care. Key technology needs for the emergency medical services helicopter of the future include the riding quality of fixed wing aircraft (reduced noise and vibration), no tail rotor, small rotor, small rotor diameter, improved visibility, crashworthy vehicle, IFR capability, more affordability high reliability, fuel efficient, and specialized cabins to hold medical/diagnostic and communications equipment. Approaches to a national emergency medical service are discussed.

Riser equipment decontamination engineering task plan

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

On October 15, 1998, two Characterization Project Operations (CPO) employees were found to have contaminated clothing. An operator had 300,000-dpm/100cm2 beta/gamma, no alpha, contamination on his coat sleeve and a Radiation Control Technician (RCT) had 10,000 dpm/100cm2 beta/gamma, no alpha, on his shirt sleeve. The CPO swing shift crew was working in TX tank farm, performing sampling activities at 241-TX-113. TX tank farm is a ''clean farm'' and does not require anti-contamination clothing for entry. The CPO personnel were dressed in normal work clothes. An operator and an RCT were performing a pre-job survey that involved removing bagging around the riser equipment. When the RCT saw that the contamination readings from smear samples of the riser equipment were greater than expected, the job was suspended. Crew members were then directed to areas of lower background radiation for personnel surveys. During personnel surveys, reportable contamination was found on the coat sleeve of the operator who had been involved in the pre-job survey and on the shirt sleeve of the RCT who had been involved in the pre-job survey. No other personnel were found to be contaminated. Because of this off normal event Characterization Engineering was given the following corrective action: Examine the process methodology used for core sampling operations to determine practicality and potential long-term advantages of reducing personnel contact with contaminated equipment. This Engineering Task Plan ensures that LMHC 1998a, Corrective Action No.7 is completely addressed by Characterization Engineering. The deliverable is an Engineering Study that evaluates decontamination of riser equipment components and considers additional engineered features to reduce potential exposure to workers operating the riser equipment. This engineering study shall also address any released design features that have failed to be implemented

A telemedicine support for improving medical emergency management

Directory of Open Access Journals (Sweden)

Massimo Canonico

2017-12-01

Full Text Available In this paper, we introduce a telemedicine architecture for supporting emergency patient stabilization and patient transportation to a fully equipped health care center. In particular, we focus on the description of a set of mobile apps, designed for supporting data recording and transmission during patient transportation by ambulance. Some of the apps are interfaced to the monitoring devices in the ambulance, and automatically send all the recorded data to a server at the destination center. One additional app enables the travelling personnel to input and transmit further significant patient data, or comments. At the destination center, the specialist physician is allowed to inspect the data as soon as they are received, possibly providing immediate advice. The exploitation of the apps also allows to maintain the transportation data over time, for medico-legal purposes, or to perform a-posteriori analyses. Some first evaluation results are discussed in the paper.

Emergent risks to workplace safety as a result of IT connections of and between work equipment

NARCIS (Netherlands)

Steijn, W.; Vorm, J. van der; Luijf, E.; Gallis, R.; Beek, D. van der

2016-01-01

The ever-greater integration of new technologies in work equipment is regarded by some as the fourth industrial revolution1 and referred to as ‘smart industry’2. Examples that come to mind include automation through the use of embedded software, remotely controlling heavy materials, and the

Emergency medicine and the airline passenger

Science.gov (United States)

Mohler, S. R.; Nicogossian, A.; Margulies, R. A.

1980-01-01

Problems related to immediate medical care in case of in-flight emergencies are discussed with reference to such critical types of medical emergencies as obstructed airway, cardiac dysfunction, trauma, hemorrhage, hypoxia, and pain. It is shown that training flight attendants to deal with in-flight medical emergencies and to use first-aid support equipment and essential and useful drugs may later help with stabilization of a victim and allow continuing the flight to the scheduled destination without the need for a diverted landing. Among the steps suggested in order to upgrade inflight welfare and safety of passengers are the development of an advisory circular by the FAA covering standardized training for flight attendants, regulatory action requiring upgrading of the present rudimentary first-aid kit, and the enactment of Good Samaritan legislation by the U.S. Government.

Management of Information Technology Equipment, Office of the Secretary of Defense

National Research Council Canada - National Science Library

2001-01-01

...) inventory records for information technology equipment, such as personal computers. In addition, the investigation identified security issues concerning the disposal of personal computer hard drives...

EDF national emergency organization

International Nuclear Information System (INIS)

Laverge, J.

1992-01-01

The scope of French nuclear power led Electricite de France (EDF) to design standard products, manufactured in series but adaptable to different sites. Standardization is based on the decision on a single technology: pressurized water reactors (PWR). Thirty-four 900 MW and seventeen 1300 MW units are in operation on seventeen sites. The specific nature of French organization for normal operation and accident management results from equipment standardization and single licensee. This specificity is based on emergency plan standardization and highly structured national organization. Figs

Materials Selection And Fabrication Practices For Food Processing Equipment Manufacturers In Uganda

Directory of Open Access Journals (Sweden)

John Baptist Kirabira

2017-08-01

Full Text Available The food processing industry is one of the fast-growing sub-sectors in Uganda. The industry which is majorly composed of medium and small scale firms depends on the locally developed food processing equipment. Due to lack of effective materials selection practices employed by the equipment manufacturers the materials normally selected for most designs are not the most appropriate ones hence compromising the quality of the equipment produced. This has not only led to poor quality food products due to contamination but could also turn out health hazardous to the consumers of the food products. This study involved the assessment of the current materials selection and fabrication procedures used by the food processing equipment manufacturers with a view of devising best practices that can be used to improve the quality of the food products processed by the locally fabricated equipment. Results of the study show that designers experience biasness and desire to minimize cost compromise the materials selection procedure. In addition to failing to choose the best material for a given application most equipment manufacturers are commonly fabricating equipment with inadequate surface finish and improper weldments. This hinders the equipments ability to meet food hygiene standards.

The Effectiveness of Seismic Isolation System for Nuclear Equipment

International Nuclear Information System (INIS)

Kim, Min-Kyu; Choun, Young-Sun; Seo, Jeong-Moon

2005-04-01

In this study, the Emergency Diesel Generator and Off-site Transformer were selected for isolation. For the selection of the most suitable base isolation system, the literature review and the numerical analysis were performed. For the decision of the parameter of isolation system, the sensitivity analysis was performed. Finally the conceptual design of each equipment was performed. In case of EDG, the Coil Spring and Viscous Damper system was selected for isolation system and 45% isolation effect was determined. For the OST, the FPS was selected and 69% isolation effect was determined

The Effectiveness of Seismic Isolation System for Nuclear Equipment

Energy Technology Data Exchange (ETDEWEB)

Kim, Min-Kyu; Choun, Young-Sun; Seo, Jeong-Moon

2005-04-15

In this study, the Emergency Diesel Generator and Off-site Transformer were selected for isolation. For the selection of the most suitable base isolation system, the literature review and the numerical analysis were performed. For the decision of the parameter of isolation system, the sensitivity analysis was performed. Finally the conceptual design of each equipment was performed. In case of EDG, the Coil Spring and Viscous Damper system was selected for isolation system and 45% isolation effect was determined. For the OST, the FPS was selected and 69% isolation effect was determined.

Inquiry about the uses of special equipment (CT equipment, angiography systems, mammography devices, screens)

International Nuclear Information System (INIS)

Schwager, P.; Stieve, F.E.

1986-01-01

There are at least 1100 special devices in medical establishment in Bavaria which require special inspection and surveillance with regard to quality of equipment and radiation protection. In addition, there are at least 53 tomographs available for operation, and at least 120 installed X-ray screens. These devices need special approval testing and quality control services as they contribute a very significant amount of the medically indicated radiation exposure of the population. Appropriate measures are explained that can be applied in order to reduce the medical radiation exposure to an optimum. (orig.) [de

29 CFR 97.32 - Equipment.

Science.gov (United States)

2010-07-01

...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

44 CFR 13.32 - Equipment.

Science.gov (United States)

2010-10-01

...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

24 CFR 85.32 - Equipment.

Science.gov (United States)

2010-04-01

...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

43 CFR 12.72 - Equipment.

Science.gov (United States)

2010-10-01

...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

[Investigation of emergency capacities for occupational hazard accidents in silicon solar cell producing enterprises].

Science.gov (United States)

Yang, D D; Xu, J N; Zhu, B L

2016-11-20

Objective: To investigate and analyze the influential factors of occupational hazard acci-dents, emergency facilities and emergency management in Silicon solar cell producing enterprises, then to pro-vide scientific strategies. Methods: The methods of occupationally healthy field investigating, inspecting of ven-tilation effectiveness, setup of emergency program and wearing chemical suit were used. Results: The mainly occupational hazard accidents factors in the process of Silicon solar cell producing included poisoning chemi-cals, high temperature, onizing radiation and some workplaces. The poisoning chemicals included nitric acid, hydrofluoric acid, sulfuric acid, hydrochloric acid, sodium hydroxide, potassium hydroxide, chlorine, phos-phorus oxychloride, phosphorus pentoxide, nitrogen dioxide, ammonia, silane, and so on; the workplaces in-cluded the area of producing battery slides and auxiliary producing area. Among the nine enterprises, gas detec-tors were installed in special gas supplying stations and sites, but the height, location and alarmvalues of gas detectors in six enterprises were not according with standard criteria; emergency shower and eyewash equip-ment were installed in workplaces with strong corrosive chemicals, but the issues of waste water were not solved; ventilation systems were set in the workplaces with ammonia and silane, but not qualified with part lo-cations and parameters in two enterprises; warehouses with materials of acid, alkali, chemical ammonia and phosphorus oxychloride were equipped with positive - pressure air respirator resuscitator and emergency cabi-nets, but with insufficient quantity in seven enterprises and expiration in part of products. The error rate of set-up emergency program and wearing chemical cloth were 30%~100% and 10%~30%, respectively. Among the nine enterprises, there were emergency rescue plans for dangerous chemical accidents, but without profession-al heatstroke and irradiation accident emergency plans

An overview of the Environmental Response Team's air surveillance procedures at emergency response activities

Energy Technology Data Exchange (ETDEWEB)

Turpin, R.D.; Campagna, P.R. (U.S. Environmental Protection Agency, Edison, NJ (USA))

The Safety and Air Surveillance Section of the United States Environmental Protection Agency's Environmental Response Team responds to emergency air releases such as tire fires and explosions. The air surveillance equipment and procedures used by the organization are described, and case studies demonstrating the various emergency response activities are presented. Air response activities include emergency air responses, occupational and human health air responses and remedial air responses. Monitoring and sampling equipment includes photoionization detectors, combustible gas meters, real-time aerosol monitors, personal sampling pumps, and high flow pumps. Case histories presented include disposal of dioxane from a cotton plant, response to oil well fires in Kuwait, disposal of high pressure cylinders in American Samoa, and response to hurricane Hugo. 3 refs., 1 tab.

Consensus on items and quantities of clinical equipment required to deal with a mass casualties big bang incident: a national Delphi study.

Science.gov (United States)

Duncan, Edward A S; Colver, Keith; Dougall, Nadine; Swingler, Kevin; Stephenson, John; Abhyankar, Purva

2014-02-22

Major short-notice or sudden impact incidents, which result in a large number of casualties, are rare events. However health services must be prepared to respond to such events appropriately. In the United Kingdom (UK), a mass casualties incident is when the normal response of several National Health Service organizations to a major incident, has to be supported with extraordinary measures. Having the right type and quantity of clinical equipment is essential, but planning for such emergencies is challenging. To date, the equipment stored for such events has been selected on the basis of local clinical judgment and has evolved without an explicit evidence-base. This has resulted in considerable variations in the types and quantities of clinical equipment being stored in different locations. This study aimed to develop an expert consensus opinion of the essential items and minimum quantities of clinical equipment that is required to treat 100 people at the scene of a big bang mass casualties event. A three round modified Delphi study was conducted with 32 experts using a specifically developed web-based platform. Individuals were invited to participate if they had personal clinical experience of providing a pre-hospital emergency medical response to a mass casualties incident, or had responsibility in health emergency planning for mass casualties incidents and were in a position of authority within the sphere of emergency health planning. Each item's importance was measured on a 5-point Likert scale. The quantity of items required was measured numerically. Data were analyzed using nonparametric statistics. Experts achieved consensus on a total of 134 items (54%) on completion of the study. Experts did not reach consensus on 114 (46%) items. Median quantities and interquartile ranges of the items, and their recommended quantities were identified and are presented. This study is the first to produce an expert consensus on the items and quantities of clinical equipment

Sensor fusion for active vibration isolation in precision equipment

NARCIS (Netherlands)

Tjepkema, D.; van Dijk, Johannes; Soemers, Herman

2012-01-01

Sensor fusion is a promising control strategy to improve the performance of active vibration isolation systems that are used in precision equipment. Normally, those vibration isolation systems are only capable of realizing a low transmissibility. Additional objectives are to increase the damping

Guidelines for the preparation of emergency operating procedures. Resolution of comments on NUREG-0799

International Nuclear Information System (INIS)

1982-08-01

The purpose of this document is to identify the elements necessary for utilities to prepare and implement a program of Emergency Operating Procedures (EOPs) for use by control room personnel to assist in mitigating the consequences of a broad range of accidents and multiple equipment failures. This document applies only to the EOPs so designated; it does not address emergency preparedness or emergency planning. It also represents the resolution of comments on NUREG-0799, Draft Criteria for Preparation of Emergency Operating Procedures

Maintenance of fire systems and equipment at Virginia Power

International Nuclear Information System (INIS)

Doubrely, E.B. Jr.

1989-01-01

The basics of fire protection systems maintenance are well codified and documented in the National Fire Codes published by the National Fire Protection Association. In addition, Insurers often promulgate minimum standards for fire protection systems design and maintenance to which they attach conditions of insurability. Regulatory agencies and even in-house corporate policies can impact the maintenance of fire protection systems and equipment. This presentation will focus on the various methods and alternate ways of performing system maintenance, whether required by code, insurer, or by some regulatory commitment at Virginia Powers North Anna and Surry nuclear power stations. The approach to performing similar work is handled differently at each station. This difference can be attributed to proximity to outside assistance as well as plant philosophy. In addition to station maintenance practices, a discussion of in-house servicing of portable fire suppression equipment is offered. 1 tab

IRRIGATION STATION EQUIPMENT FOR PREVENTING THE USE OF LOW WATER QUALITY

Directory of Open Access Journals (Sweden)

Constantin Nicolescu

2010-01-01

Full Text Available In Romania the economically efficient irrigated area is estimated at 3.5 million hectares. On national scale there is nointegrated approach for monitoring the quantity and quality of the irrigation water, using adequate equipment at thepumping station. On international scale, in many countries the pumping stations are provided with equipment formonitoring, on real time, the quality or the pumped water and for warning about critical situations (emergencies.This paper describes a technical solution consisting of equipment which monitors the following parameters of waterpumped in irrigation systems: turbidity, pH, CE at 25 o C, Na+, Cl-. The lapse of time for monitoring is of 10 to 60 min.The main components are the following: the sampling pump (submersible the monitoring board, the repression pipe ofthe analyzed water. Warnings are made about values exceeding the programmed level for each monitored parameter,about the fact that the pump and agitator do not work or about any other source of damage.The technical solution and equipment were tested at a pumping station which uses water from Danube, in most casesmixed with water originating from drainage. Results showed a reduction of the total content of soluble salts from soiland of their negative impact upon the crops, a reduction of the degree of river alluvial deposits within the irrigationsystem and reduction of the energetic consumption required for pumping.

The TransPetro emergency response system

Energy Technology Data Exchange (ETDEWEB)

Filho, A.T.F.; Cardoso, V.F.; Carbone, R.; Berardinelli, R.P. [Petrobras-TransPetro, Rio de Janeiro (Brazil); Carvalho, M.T.M.; Casanova, M.A. [Pontificia Univ. Catolica, Rio de Janeiro (Brazil). Dept. de Informatica, TeCGraf

2004-07-01

Petrobras-TransPetro developed the TransPetro Emergency Response System in response to emergency situations at large oil pipelines or at terminal facilities located in sea or river harbour areas. The standard of excellence includes full compliance with environmental regulations set by the federal government. A distributed workflow management software called InfoPAE forms the basis of the system in which actions are defined, along with geographic and conventional data. The first prototype of InfoPAE was installed in 1999. Currently it is operational in nearly 80 installations. The basic concepts and functionality of the TransPetro Emergency Response System were outlined in this paper with reference to the mitigative actions that are based on an evaluation of the organization of the emergency teams; the communication procedures; characterization of the installations; definition of accidental scenarios; environmental sensitivity maps; simulation of oil spill trajectories and dispersion behaviour; geographical data of the area surrounding the installations; and, other conventional data related to the installations, including available equipment. The emergency response team can take action as soon as an accident is detected. The action plan involves characterizing several scenarios and delegating mitigative actions to specific sub-teams, each with access to geographic data on the region where the emergency occurred. 13 refs., 3 figs.

30 CFR 75.504 - Permissibility of new, replacement, used, reconditioned, additional, and rebuilt electric face...

Science.gov (United States)

2010-07-01

... STANDARDS-UNDERGROUND COAL MINES Electrical Equipment-General § 75.504 Permissibility of new, replacement... new, replacement, used, reconditioned, and additional electric face equipment used in any mine..., unless in the opinion of the Secretary, such equipment or necessary replacement parts are not available...

Training programs for emergency response personnel at Hanford

International Nuclear Information System (INIS)

Oscarson, E.E.

1979-01-01

The Three Mile Island reactor accident has focused attention on emergency planning and preparedness including selection and training of personnel. At Hanford, Pacific Northwest Laboratory (PNL) is in the unique position of providing emergency response personnel, planning, training and equipment not only for its own organization and facilities but also for the Hanford Site in general, as well as the Interagency Radiological Assistance Plan (IRAP) Region 8 Team. Team members are chosen for one or more of the emergency teams based upon professional education and/or experience as well as interest, aptitude and specialized knowledge. Consequently, the initial training orientation of each new team member is not directed toward general professional ability, but rather toward specialized knowledge required to carry out their assigned emergency tasks. Continual training and practice is necessary to maintain the interest and skills for effectively coping with major emergencies. The types of training which are conducted include: tests of emergency systems and/or procedures; drills involving plant employees and/or emergency team members (e.g., activation of emergency notification systems); short training sessions on special topics; and realistic emergency exercises involving the simulation of major accidents wherein the emergency team must solve specific problems on a real time basis

Electrical equipment distributors assuming greater role as suppliers to electric utilities

International Nuclear Information System (INIS)

Anon.

1990-01-01

A survey was conducted of Canada's largest distributors of electrical equipment to the utility market. Summaries are presented of the views of the major respondents concerning market trends and future challenges. Distributors have emerged as a supply source to utilities over the past two decades. Before then, electric utilities did virtually all their business directly with the manufacturers and rarely with distributors. One reason for this situation was that direct dealing with manufacturers was perceived by the utilites as providing better access to technical advice. Distributors have grown significantly since then and many have their own expert technical staff and provide full support for their products. Various advantages for utilities in dealing with distributors are noted: ability to supply most needs relatively rapidly from stock, simplification of ordering, improved inventory management, and savings in brokerage and other costs associated with imported equipment

Use of remote video auditing to validate Ebola level II personal protective equipment competency.

Science.gov (United States)

Allar, Peter J; Frank-Cooper, Madalyn

2015-06-01

Faced with an Ebola-related mandate to regularly train frontline hospital staff with the donning and doffing of personal protective equipment, a community hospital's emergency department implemented remote video auditing (RVA) to assist in the training and remediation of its nursing staff. RVA was found to be useful in assessing performance and facilitating remediation. Copyright 2015, SLACK Incorporated.

Remote handling equipment

International Nuclear Information System (INIS)

Clement, G.

1984-01-01

After a definition of intervention, problems encountered for working in an adverse environment are briefly analyzed for development of various remote handling equipments. Some examples of existing equipments are given [fr

Analysis of NPP pipes and equipment damage in life time prolongation

International Nuclear Information System (INIS)

Tkachev, V.V.; Zheltukhin, K.K.

2008-01-01

Paper describes a procedure to calculate the probability of pipes and equipment failure taking account of both the service records of the structures under various conditions and their aging. The parameters characterizing applied loads, failures, as well as metal strength, mechanical and thermal properties serve as the arbitrary values used in the described procedure. Paper presents an example of the probability calculation of failure of the RBMK emergency feed pump recirculation pipes when their service life is prolonged [ru

Injury survey of a non-traditional 'soft-edged' trampoline designed to lower equipment hazards.

Science.gov (United States)

Eager, David B; Scarrott, Carl; Nixon, Jim; Alexander, Keith

2013-01-01

In Australia trampolines contribute one quarter of all childhood play equipment injuries. The objective of this study was to gather and evaluate injury data from a non-traditional, 'soft-edged', consumer trampoline, where the design aimed to minimise injuries from the equipment and from falling off. The manufacturer of the non-traditional trampoline provided the University of Technology Sydney with their Australian customer database. The study involved surveys in Queensland and New South Wales, between May 2007 and March 2010. Initially injury data was gathered by a phone interview pilot study, then in the full study, through an email survey. The 3817 respondents were the carers of child users of the 'soft-edge' trampolines. Responses were compared with Australian and US emergency department data. In both countries the proportion of injuries caused by the equipment and falling off was compared with the proportion caused by the jumpers to themselves or each other. The comparisons showed a significantly lower proportion resulted from falling-off or hitting the equipment for this design when compared to traditional trampolines, both in Australia and the US. This research concludes that equipment-induced and falling-off injuries, the more severe injuries on traditional trampolines, can be significantly reduced with appropriate trampoline design.

Waste Handling Equipment Development Test and Evaluation Study

International Nuclear Information System (INIS)

R.L. Tome

1998-01-01

planned and conducted by the appropriate design organization as part of the design process. The scope of this study, therefore, will address only surface development testing activities that will be performed prior to detail design and procurement of the MGR surface waste handling equipment. Testing to support development of additional MGR surface equipment and operations, such as cooling of shipping casks and dual-purpose canisters (DPCs) prior to pool entry, decontamination of disposal containers (DCs), and recovery systems for various equipment, is not addressed in this study. These equipment items/systems were not developed for VA and are not currently identified as specific MGR surface waste handling equipment

Situation analysis of physical independence of the equipment and safety circuits of Almaraz NPP regarding R.G. 1.75 rev.3 (2005)

International Nuclear Information System (INIS)

Seijas Portela, S.

2010-01-01

Situation analysis of physical independence of the electrical equipment and circuits CN safety Almaraz about R.G. 1.75 rev. 3. (2005) The aim of this paper is to present the work done in the analysis of the physical separation of redundant safety electrical equipment (emergency diesel generators, medium voltage, electrical cabinets, etc.) and physical separation of circuits and electrical conduits.

Controlling the quality of replacement parts in nuclear station, class 1E equipment

International Nuclear Information System (INIS)

Pierson, R.K.; Clemons, R.W.

1984-01-01

Nuclear station owners have traditionally purchased replacement parts for Class 1E equipment from the original supplier of the equipment. By this method, part and equipment quality could be maintained. In recent years, however, this traditional source of parts has continuously declined as an increasing number of original equipment suppliers stop producing Class 1E equipment or no longer stock parts for older equipment. When replacement parts for Class 1E equipment are not obtainable from the original suppliers, equipment owners have created a variety of methods for assuring the quality of parts obtained from other sources. A standard that provides direction and guidance for maintaining the quality of Class 1E equipment when repaired with parts from alternate sources is, therefore, needed to assure the methods in use are satisfactory and to alert the equipment owners to additional acceptable methods. The standard has now been proposed. IEEE Standard P934 (June, 1983 Draft): ''Requirements for Replacement Parts for Class 1E Equipment in Nuclear Power Generating Stations'' (Ref-3) consist of an introductory section followed by sections on part selection, procurement, replacement (including inspections and tests), non-conforming conditions and records. The proposed standard also includes a non-mandatory appendix on acceptable procurement methods and a summary intended to assist the user in selecting a proper procurement method

Used energy-related laboratory equipment grant program for institutions of higher learning. Eligible equipment catalog

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

This is a listing of energy related equipment available through the Energy-Related Laboratory Equipment Grant Program which grants used equipment to institutions of higher education for energy-related research. Information included is an overview of the program, how to apply for a grant of equipment, eligibility requirements, types of equipment available, and the costs for the institution.

User's manual for the master equipment list. Phase 1

International Nuclear Information System (INIS)

Sandoval, J.D.

1997-01-01

This manual is intended to provide a user with enough detailed instruction to guide them through the Master Equipment List Phase 1 (MEL Phase 1) application system operations. The MEL Phase 1 application is a database system that stores Equipment Identification Number (EIN) information to support equipment tracking in the 200E and 200W Tank Farms for the Tank Waste Remediation System Division. The MEL Phase 1 application supports both the user application and administrative control functions. The user application functions include: viewing by Folder, reporting, performing queries, and editing specific data. The administrative control functions include: maintaining valid user identifications, passwords, privileges, defining drop-down lists, and review of the change log relating to EIN data entries, additions, deletions, and editing. The scope of this User's Manual is to discuss these functions and is intended to guide users and answer questions regarding the MEL Phase 1 application

Equipment repair in coal mines

Energy Technology Data Exchange (ETDEWEB)

Zhang, S

1982-01-01

Most equipment in Chinese coal mines consists of machinery and equipment produced in the 1950s; the efficiency of 4-62, CTD-57 and 70B/sub 2/ ventilators is 15% lower than that of new ones; that of SSM and AYaP pumps, 10% lower than of modern ones. Equipment renovation is done in three ways: replacing obsolete equipment with new equipment of the same type; improving the performance of existing equipment by introducing efficiency and reconstruction; and replacing obsolete equipment with advanced equipment. It is indicated that the second way, for example, replacement of 4-62 ventilator blades with a maximum efficiency of 73% by 4-72 ventilator blades raises its efficiency to 90%. Replacing the 8DA-8x3 water pump, having a maximum efficiency of 63%, with the 200D 43x3 pump with a maximum efficiency of 78%, enables an electricity savings of 7000 yuan per year, which exceeds all replacement costs (600 yuan). The need to improve equipment maintenance and preventive work to increase equipment service life and to introduce new techniques and efficiency is noted.

Regulatory controls for NORM contamination: Emerging issues and strategies

International Nuclear Information System (INIS)

Wennerberg, Linda

1992-01-01

Naturally occurring and accelerator-produced radioactive material (NORM) faces the increasing likelihood of federal or state regulatory control. Public concern and limited preliminary survey data fuel the debate over the necessity, approach, and jurisdiction of a NORM regulatory strategy. This debate requires the resolution of technical controversies and potentially competing state and federal agency interests. An additional facet of the debate is the impact of regulation upon traditionally non-nuclear industries, such as oil and gas production. Regulatory response has been initiated in several states, such as Louisiana's controls on equipment used in oil and gas production, to control specific industrial activities which generate NORM. A more comprehensive, generic federal strategy to control NORM contamination is also under review by the Environmental Protection Agency. This paper will detail the emerging technical issues, federal and state regulatory strategies under consideration, and evaluate the efficacy of selected regulatory approaches. (author)

Base Stabilization Guidance and Additive Selection for Pavement Design and Rehabilitation

Science.gov (United States)

2017-12-01

Significant improvements have been made in base stabilization practice that include design specifications and methodology, experience with the selection of stabilizing additives, and equipment for distribution and uniform blending of additives. For t...

BP volume reduction equipment

International Nuclear Information System (INIS)

Kitamura, Yoshinori; Muroo, Yoji; Hamanaka, Isao

2003-01-01

A new type of burnable poison (BP) volume reduction system is currently being developed. Many BP rods, a subcomponent of spent fuel assemblies are discharged from nuclear power reactors. This new system reduces the overall volume of BP rods. The main system consists of BP rod cutting equipment, equipment for the recovery of BP cut pieces, and special transport equipment for the cut rods. The equipment is all operated by hydraulic press cylinders in water to reduce operator exposure to radioactivity. (author)

Exercise Equipment: Neutral Buoyancy

Science.gov (United States)

Shackelford, Linda; Valle, Paul

2016-01-01

Load Bearing Equipment for Neutral Buoyancy (LBE-NB) is an exercise frame that holds two exercising subjects in position as they apply counter forces to each other for lower extremity and spine loading resistance exercises. Resistance exercise prevents bone loss on ISS, but the ISS equipment is too massive for use in exploration craft. Integrating the human into the load directing, load generating, and motion control functions of the exercise equipment generates safe exercise loads with less equipment mass and volume.

22 CFR 135.32 - Equipment.

Science.gov (United States)

2010-04-01

... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

21 CFR 1403.32 - Equipment.

Science.gov (United States)

2010-04-01

... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

45 CFR 602.32 - Equipment.

Science.gov (United States)

2010-10-01

... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

49 CFR 18.32 - Equipment.

Science.gov (United States)

2010-10-01

... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

34 CFR 80.32 - Equipment.

Science.gov (United States)

2010-07-01

... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

10 CFR 600.232 - Equipment.

Science.gov (United States)

2010-01-01

... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

45 CFR 1183.32 - Equipment.

Science.gov (United States)

2010-10-01

... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

Recovery of Ir-192 sources during emergency situations

International Nuclear Information System (INIS)

Quadros, C.L.; Conceicao, M.A. da

1988-01-01

During operations for the carrying out of services through the utilization of Ir-192 radio sources in radiographic tests of equipment, emergency situations may occur due to various causes and which bring radiologic accidents with doses exceeding the maximum alloewd. This work has the purpose to submit and analyze the major types of radiological accidents and its consequences for the installations and the procedures for the recuperation of sources during such situations. Another aspect to be mentioned shall be the interruption of services - such as production - and which is to be the lowest possible during the emergency. (author) [pt

Emergency reactor cooling systems for the experimental VHTR

International Nuclear Information System (INIS)

Mitake, Susumu; Suzuki, Katsuo; Miyamoto, Yoshiaki; Tamura, Kazuo; Ezaki, Masahiro.

1983-03-01

Performances and design of the panel cooling system which has been proposed to be equipped as an emergency reactor cooling system for the experimental multi purpose very high temperature gas-cooled reactor are explained. Effects of natural circulation flow which would develop in the core and temperature transients of the panel in starting have been precisely investigated. Conditions and procedures for settling accidents with the proposed panel cooling system have been also studied. Based on these studies, it has been shown that the panel cooling system is effective and useful for the emergency reactor cooling of the experimental VHTR. (author)

46 CFR 108.901 - Muster list and emergency instructions.

Science.gov (United States)

2010-10-01

... UNITS DESIGN AND EQUIPMENT Muster List § 108.901 Muster list and emergency instructions. (a) General...) Each muster list must specify the actions to be taken by the crew and industrial personnel when each... specify the duties assigned to the different industrial personnel and members of the crew that include— (i...

Development of manufacturing equipment and QC equipment for DUPIC fuel

International Nuclear Information System (INIS)

Yang, Myung Seung; Park, J.J.; Lee, J.W.; Kim, S.S.; Yim, S.P.; Kim, J.H.; Kim, K.H.; Na, S.H.; Kim, W.K.; Shin, J.M.; Lee, D.Y.; Cho, K.H.; Lee, Y.S.; Sohn, J.S.; Kim, M.J.

1999-05-01

In this study, DUPIC powder and pellet fabrication equipment, welding system, QC equipment, and fission gas treatment are developed to fabricate DUPIC fuel at IMEF M6 hot cell. The systems are improved to be suitable for remote operation and maintenance with the manipulator at hot cell. Powder and pellet fabrication equipment have been recently developed. The systems are under performance test to check remote operation and maintenance. Welding chamber and jigs are designed and developed to remotely weld DUPIC fuel rod with manipulators at hot cell. Remote quality control equipment are being tested for analysis and inspection of DUPIC fuel characteristics at hot cell. And trapping characteristics is analyzed for cesium and ruthenium released under oxidation/reduction and sintering processes. The design criteria and process flow diagram of fission gas treatment system are prepared incorporating the experimental results. The fission gas treatment system has been successfully manufactured. (Author). 33 refs., 14 tabs., 91 figs

Qualification of Electrical Equipment in Nuclear Power Plants - Management of ageing

International Nuclear Information System (INIS)

Spaang, Kjell; Staahl, Gunnar

2013-02-01

The purpose of this report is to describe programs and tools for assessment of accomplished and documented qualification with respect to ageing of electrical equipment and for development of complimentary ageing management programs. In addition to description of complete programs for management of ageing, tools for validation of the status with regard to ageing of installed ('old') equipment and, where needed, for complementation of their qualification are also included. The report is restricted to safety related equipment containing ageing sensitive parts, mainly organic materials. To this category belong cables and cable joints and a number of equipment containing oils, seals (o-rings), etc. For equipment located in the containment, the possibilities of continuous supervision are limited. The accessibility for regular inspections is also limited in many cases. The main part of this report deals with the qualification of such equipment. Some safety related equipment outside the containment can be located in areas where they are subjected to high temperature and other excessive environmental stresses during normal operation and in areas affected by an accident. Therefore, some material is given also on qualification of equipment located outside containment with better possibilities for frequent inspection and supervision. Part 1 of the report is an executive summary with a general review of the methodologies and their application. The more detailed description of the programs and underlying material, useful data, etc. is given in Part 2

New Emergency control center of Slovenske Elektrarne Bohunice NPP

International Nuclear Information System (INIS)

Pecko, E.

2012-01-01

Emergency preparedness of nuclear power plant and operation assurance in case of a possible emergency calls to have devices for emergency response with equipment for rapid detection and continuous evaluation of anticipated events. Chief executive body designated to manage a nuclear power plant during major events is the emergency committee (EC). Emergency Committee is a part of the Emergency Response Organization (ERO). The following centers are on alert to ensure the activities of the ERO - Emergency Response office: - control room (CR) and emergency control room (ECR); - emergency management center (EMC); - Monitoring Centre (MC); - emergency backup control center (EBCC); - congregations of civil protection (CP) and CP shelters; - communications with warning and notification system (VARVYR). From a historical and practical point of view in the vicinity of Jaslovske Bohunice has been set up a joint emergency control center. The center was located on the territory of the former already inoperative V1 NPP. V1 NPP is currently integrated into the organizational structure of JAVYS. Operating Bohunice V2 NPP plant is a designated part of the Slovenske Elektrarne, a. s., whose majority owner is an Italian operator ENEL. In terms of various relevant factors, it was decided to build a new emergency management center on the territory of operating V2 NPP, meet the current standards.

Equipment support for the implementation of safeguards

International Nuclear Information System (INIS)

Arlt, R.; Bosler, G.; Goldfarb, M.; Schanfein, M.; Whichello, J.

2001-01-01

Full text: The provision of effective, reliable, and user-friendly equipment needed for the implementation of safeguards is one of the main objectives of the Division of Technical Services (SOTS) in the Department of Safeguards. As an outcome of a review by an independent external consultant firm, the instrumentation sections of the SGTS were reorganized in January 2001 into two new sections, the Section for NDA Systems and Seals (TNS) and Section for Installed Systems (TIE). Each section has 'cradle-to-grave' responsibilities for development, implementation, maintenance, and decommissioning of safeguards instruments and measurement systems. Unattended assay, monitoring and surveillance instruments are the responsibility of TIE while attended nondestructive assay (NDA) instruments and seals are handled by TNS. The principal goals of both sections are to define equipment requirements based on Departmental needs, to coordinate Support Programme tasks concerning development and implementation activities, to provide system engineering of commercial components, manage laboratory and to do field testing and prove system suitability for defined safeguards applications. In addition both sections coordinate equipment and supply needs for the Department, including acquisition, preparation, servicing, installation, commissioning, troubleshooting, maintenance and repair, ensuring their availability when needed. As required, TIE and TNS provide specialized field support to the Operations Divisions. Each section is working to standardize equipment as much as possible and reduce the number of instruments performing the same function. This reduces both inspector and technician training, required parts inventories, and overall life-cycle costs. Development based on User Needs from the Operations Divisions follows a strict quality control program that includes a thorough qualification testing procedure with the last phase being field-testing under actual facility conditions. A

Development of the testing procedure for units and elements of mining equipment

Directory of Open Access Journals (Sweden)

P. B. Gerike

2017-09-01

improvement of normalization using spectral masks and unified diagnostic criteria. Implementation of the principles of the developed testing methodology will increase reliability of mining equipment and minimize the number of emergency failures of complex expensive equipment, which in the end will generally have a positive impact on the safety of mining operations.

Relatos da equipe de saúde quanto às práticas educativas ao vitimado no trânsito durante a hospitalização/reabilitação num hospital de emergência Health care team's reports on educational practices for road traffic victims during hospitalization/rehabilitation in an emergency hospital

Directory of Open Access Journals (Sweden)

Luiza Jane Eyre de Souza Vieira

2010-03-01

Full Text Available O objetivo deste estudo foi analisar os relatos da equipe de saúde quanto às práticas educativas ao vitimado no trânsito durante a hospitalização/reabilitação, visando à minimização da instalação de sequelas traumato-ortopédicas. Este estudo foi realizado com 10 profissionais da equipe de saúde que trabalham em um hospital público de emergência em Fortaleza, Ceará, Brasil, em 2006. A entrevista semiestruturada foi a técnica utilizada para a coleta de dados, os quais foram submetidos à análise temática e discutidos à luz da Educação em Saúde e Promoção da Saúde. Para os participantes, a concepção sobre a prática educativa convergiu para o caráter preventivo, informacional e normativo; a equipe de saúde, apesar de não exercer o processo de assistência terapêutica integral e humanizada, alguns profissionais da equipe de saúde desenvolvem de forma tímida a prática educativa, desmitificando a Promoção da Saúde como foco da atenção primária. Desse modo, a reorientação da prática da equipe de saúde, com enfoque interdisciplinar à vítima de acidente de trânsito, pode ser um diferencial para minimizar a instalação de sequelas.The paper aims at analyzing the health care team's reports on educational practices to road traffic victims during the period of hospitalization and rehabilitation, trying to reduce traumatic orthopedic sequelae. The study was carried out with 10 professionals from the health care team who work in a public emergency hospital in the city of Fortaleza, State of Ceará, Brazil, in 2006. The semi-structured interview was the technique for collecting data and these were submitted to thematic analysis and then discussed in the light of Health Education and Health Promotion. To the participants, the conception of educational practice converged to a preventive, informational, and normative approach; although the health care team did not accomplish with integrality and humanization the

45 CFR 1174.32 - Equipment.

Science.gov (United States)

2010-10-01

... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use... requirements. Procedures for managing equipment (including replacement equipment), whether acquired in whole or... original or replacement equipment acquired under a grant or subgrant is no longer needed for the original...

45 CFR 1157.32 - Equipment.

Science.gov (United States)

2010-10-01

... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use... requirements. Procedures for managing equipment (including replacement equipment), whether acquired in whole or... original or replacement equipment acquired under a grant or subgrant is no longer needed for the original...

76 FR 26279 - Procurement List; Proposed Additions

Science.gov (United States)

2011-05-06

...-service area; clean and sanitize food service equipment, utensil cleaning, and dishwashing; clean pots... additions to the Procurement List. SUMMARY: The Committee is proposing to add services to the Procurement... in this notice will be required to procure the services listed below from nonprofit agencies...

Cold Atmospheric Plasma Technology for Decontamination of Space Equipment

Science.gov (United States)

Thomas, Hubertus; Rettberg, Petra; Shimizu, Tetsuji; Thoma, Markus; Morfill, Gregor; Zimmermann, Julia; Müller, Meike; Semenov, Igor

2016-07-01

Cold atmospheric plasma (CAP) technology is very fast and effective in inactivation of all kinds of pathogens. It is used in hygiene and especially in medicine, since the plasma treatment can be applied to sensitive surfaces, like skin, too. In a first study to use CAP for the decontamination of space equipment we could show its potential as a quite promising alternative to the standard "dry heat" and H2O2 methods [Shimizu et al. Planetary and Space Science, 90, 60-71. (2014)]. In a follow-on study we continue the investigations to reach high application level of the technology. First, we redesign the actual setup to a plasma-gas circulation system, increasing the effectivity of inactivation and the sustainability. Additionally, we want to learn more about the plasma chemistry processes involved in the inactivation. Therefore, we perform detailed plasma and gas measurements and compare them to numerical simulations. The latter will finally be used to scale the decontamination system to sizes useful also for larger space equipment. Typical materials relevant for space equipment will be tested and investigated on surface material changes due to the plasma treatment. Additionally, it is planned to use electronic boards and compare their functionality before and after the CAP expose. We will give an overview on the status of the plasma decontamination project funded by the Bavarian Ministry of Economics.

PROBLEMS PERTAINING TO DIVERSIFICATION OF CIVIL EQUIPMENT IN EQUIPMENT OF MILITARY PURPOSE

OpenAIRE

A. I. Kotlabay; V. A. Korobkin; V. F. Tamelo; I. V. Kostko; S. V. Kondratiev

2009-01-01

Study of directions concerning development of military equipment, its modernization with the purpose to improve its military efficiency is an actual problem for the Armed Forces, military science, designers and researchers.The paper analyzes and estimates possibilities to use civil equipment for military purpose. Problems pertaining to technologies of double application, diversification of civil equipment in military engineering machinery are considered in the paper.

Mobile Unit and Its Role in the Case of Nuclear Emergencies

International Nuclear Information System (INIS)

Franic, Z.

1998-01-01

Emergency response mobile units play a significant role in the case of nuclear emergencies. The functioning and practice of such teams depend on the nature and phase of the nuclear emergency. In the acute phase, several teams with good navigational and communication abilities performing simple measurements can provide essential data for characterization of plume location and its magnitude. Therefore, such activities are complemental with the network of telemetric radiation monitors. However, in the late phase of an accident, in order to gather reliable data needed for utilization of remedial and recovery measures, a better equipped mobile units are necessary. (author)

20 CFR 437.32 - Equipment.

Science.gov (United States)

2010-04-01

... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use.... Procedures for managing equipment (including replacement equipment), whether acquired in whole or in part... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Equipment. 437.32 Section 437.32 Employees...

Emergency escape system uses self-braking mechanism on fixed cable

Science.gov (United States)

Billings, C. R.; Mc Daris, R. A.; Mc Gough, J. T.; Neal, P. F.

1966-01-01

Slide-wire system with a twist level slide device incorporates automatic descent and braking for the safe and rapid evacuation of personnel from tall structures. This device is used on any tall structure that might require emergency evacuation. It is also used to transfer materials and equipment.

Lactic Acid Fermentation, Urea and Lime Addition: Promising Faecal Sludge Sanitizing Methods for Emergency Sanitation.

Science.gov (United States)

Anderson, Catherine; Malambo, Dennis Hanjalika; Perez, Maria Eliette Gonzalez; Nobela, Happiness Ngwanamoseka; de Pooter, Lobke; Spit, Jan; Hooijmans, Christine Maria; de Vossenberg, Jack van; Greya, Wilson; Thole, Bernard; van Lier, Jules B; Brdjanovic, Damir

2015-10-29

In this research, three faecal sludge sanitizing methods-lactic acid fermentation, urea treatment and lime treatment-were studied for application in emergency situations. These methods were investigated by undertaking small scale field trials with pit latrine sludge in Blantyre, Malawi. Hydrated lime was able to reduce the E. coli count in the sludge to below the detectable limit within 1 h applying a pH > 11 (using a dosage from 7% to 17% w/w, depending faecal sludge alkalinity), urea treatment required about 4 days using 2.5% wet weight urea addition, and lactic acid fermentation needed approximately 1 week after being dosed with 10% wet weight molasses (2 g (glucose/fructose)/kg) and 10% wet weight pre-culture (99.8% pasteurised whole milk and 0.02% fermented milk drink containing Lactobacillus casei Shirota). Based on Malawian prices, the cost of sanitizing 1 m³ of faecal sludge was estimated to be €32 for lactic acid fermentation, €20 for urea treatment and €12 for hydrated lime treatment.

Optimal Lease Contract for Remanufactured Equipment

Science.gov (United States)

Iskandar, B. P.; Wangsaputra, R.; Pasaribu, U. S.; Husniah, H.

2018-03-01

In the last two decades, the business of lease products (or equipment) has grown significantly, and many companies acquire equipment through leasing. In this paper, we propose a new lease contract under which a product (or equipment) is leased for a period of time with maximum usage per period (e.g. 1 year). This lease contract has only a time limit but no usage limit. If the total usage per period exceeds the maximum usage allowed in the contract, then the customer (as a lessee) will be charged an additional cost. In general, the lessor (OEM) provides a full coverage of maintenance, which includes PM and CM under the lease contract. It is considered that the lessor offers the lease contract for a remanufactured product. We presume that the price of the lease contract for the remanufactured product is much lower than that of a new one, and hence it would be a more attractive option to the customer. The decision problem for the lessee is to select the best option offered that fits to its requirement, and the decision problem for the lessor is find the optimal maintenance efforts for a given price of the lease option offered. We first find the optimal decisions independently for each party, and then the joint optimal decisions for both parties.

Free-world microelectronic manufacturing equipment

Science.gov (United States)

Kilby, J. S.; Arnold, W. H.; Booth, W. T.; Cunningham, J. A.; Hutcheson, J. D.; Owen, R. W.; Runyan, W. R.; McKenney, Barbara L.; McGrain, Moira; Taub, Renee G.

1988-12-01

Equipment is examined and evaluated for the manufacture of microelectronic integrated circuit devices and sources for that equipment within the Free World. Equipment suitable for the following are examined: single-crystal silicon slice manufacturing and processing; required lithographic processes; wafer processing; device packaging; and test of digital integrated circuits. Availability of the equipment is also discussed, now and in the near future. Very adequate equipment for most stages of the integrated circuit manufacturing process is available from several sources, in different countries, although the best and most widely used versions of most manufacturing equipment are made in the United States or Japan. There is also an active market in used equipment, suitable for manufacture of capable integrated circuits with performance somewhat short of the present state of the art.

Riser equipment decontamination engineering task plan; TOPICAL

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

On October 15, 1998, two Characterization Project Operations (CPO) employees were found to have contaminated clothing. An operator had 300,000-dpm/100cm2 beta/gamma, no alpha, contamination on his coat sleeve and a Radiation Control Technician (RCT) had 10,000 dpm/100cm2 beta/gamma, no alpha, on his shirt sleeve. The CPO swing shift crew was working in TX tank farm, performing sampling activities at 241-TX-113. TX tank farm is a ''clean farm'' and does not require anti-contamination clothing for entry. The CPO personnel were dressed in normal work clothes. An operator and an RCT were performing a pre-job survey that involved removing bagging around the riser equipment. When the RCT saw that the contamination readings from smear samples of the riser equipment were greater than expected, the job was suspended. Crew members were then directed to areas of lower background radiation for personnel surveys. During personnel surveys, reportable contamination was found on the coat sleeve of the operator who had been involved in the pre-job survey and on the shirt sleeve of the RCT who had been involved in the pre-job survey. No other personnel were found to be contaminated. Because of this off normal event Characterization Engineering was given the following corrective action: Examine the process methodology used for core sampling operations to determine practicality and potential long-term advantages of reducing personnel contact with contaminated equipment. This Engineering Task Plan ensures that LMHC 1998a, Corrective Action No.7 is completely addressed by Characterization Engineering. The deliverable is an Engineering Study that evaluates decontamination of riser equipment components and considers additional engineered features to reduce potential exposure to workers operating the riser equipment. This engineering study shall also address any released design features that have failed to be implemented

34 CFR 74.34 - Equipment.

Science.gov (United States)

2010-07-01

... as program income. (e) When acquiring replacement equipment, the recipient may use the equipment to... replacement equipment subject to the approval of the Secretary. (f) The recipient's property management... 34 Education 1 2010-07-01 2010-07-01 false Equipment. 74.34 Section 74.34 Education Office of the...

45 CFR 2541.320 - Equipment.

Science.gov (United States)

2010-10-01

... replacement equipment, the grantee or subgrantee may use the equipment to be replaced as a trade-in or sell... replacement equipment), whether acquired in whole or in part with grant funds, until disposition takes place... ensure the highest possible return. (e) Disposition. When original or replacement equipment acquired...

The Emergency Medical System in Greece: Opening Aeolus' Bag of Winds.

Science.gov (United States)

Kotsiou, Ourania S; Srivastava, David S; Kotsios, Panagiotis; Exadaktylos, Aristomenis K; Gourgoulianis, Konstantinos I

2018-04-13

An Emergency Medical Service (EMS) system must encompass a spectrum of care, with dedicated pre-hospital and in-hospital medical facilities. It has to be organised in such a way as to include all necessary services—such as triage accurate initial assessment, prompt resuscitation, efficient management of emergency cases, and transport to definitive care. The global economic downturn has had a direct effect on the health sector and poses additional threats to the healthcare system. Greece is one of the hardest-hit countries. This manuscript aims to present the structure of the Greek EMS system and the impact of the current economic recession on it. Nowadays, primary care suffers major shortages in crucial equipment, unmet health needs, and ineffective central coordination. Patients are also facing economic limitations that lead to difficulties in using healthcare services. The multi-factorial problem of in-hospital EMS overcrowding is also evident and has been linked with potentially poorer clinical outcomes. Furthermore, the ongoing refugee crisis challenges the national EMS. Adoption of a triage scale, expansion of the primary care network, and an effective primary–hospital continuum of care are urgently needed in Greece to provide comprehensive, culturally competent, and high-quality health care.

Visual communication and terminal equipment

International Nuclear Information System (INIS)

Kang, Cheol Hui

1988-06-01

This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.

Visual communication and terminal equipment

Energy Technology Data Exchange (ETDEWEB)

Kang, Cheol Hui

1988-06-15

This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.

Mobile Integrated Health Care and Community Paramedicine: An Emerging Emergency Medical Services Concept.

Science.gov (United States)

Choi, Bryan Y; Blumberg, Charles; Williams, Kenneth

2016-03-01

Mobile integrated health care and community paramedicine are models of health care delivery that use emergency medical services (EMS) personnel to fill gaps in local health care infrastructure. Community paramedics may perform in an expanded role and require additional training in the management of chronic disease, communication skills, and cultural sensitivity, whereas other models use all levels of EMS personnel without additional training. Currently, there are few studies of the efficacy, safety, and cost-effectiveness of mobile integrated health care and community paramedicine programs. Observations from existing program data suggest that these systems may prevent congestive heart failure readmissions, reduce EMS frequent-user transports, and reduce emergency department visits. Additional studies are needed to support the clinical and economic benefit of mobile integrated health care and community paramedicine. Copyright © 2015 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

Equipment design guidance document for flammable gas waste storage tank new equipment

International Nuclear Information System (INIS)

Smet, D.B.

1996-01-01

This document is intended to be used as guidance for design engineers who are involved in design of new equipment slated for use in Flammable Gas Waste Storage Tanks. The purpose of this document is to provide design guidance for all new equipment intended for application into those Hanford storage tanks in which flammable gas controls are required to be addressed as part of the equipment design. These design criteria are to be used as guidance. The design of each specific piece of new equipment shall be required, as a minimum to be reviewed by qualified Unreviewed Safety Question evaluators as an integral part of the final design approval. Further Safety Assessment may be also needed. This guidance is intended to be used in conjunction with the Operating Specifications Documents (OSDs) established for defining work controls in the waste storage tanks. The criteria set forth should be reviewed for applicability if the equipment will be required to operate in locations containing unacceptable concentrations of flammable gas

Environmental/dynamic mechanical equipment qualification and dynamic electrical equipment qualification program (EDQP)

International Nuclear Information System (INIS)

Hunter, J.A.

1984-01-01

Equipment qualification research is being conducted to investigate acceptable criteria, requirements, and methodologies for the dynamic (including seismic) and environmental qualification of mechanical equipment and for the dynamic (including seismic) qualification of electrical equipment. The program is organized into three elements: (1) General Research, (2) Environmental Research, and (3) Dynamic Research. This paper presents the highlights of the results to date in these three elements of the program

Reliability and maintainability data acquisition in equipment development tests

International Nuclear Information System (INIS)

Haire, M.J.; Gift, E.H.

1983-10-01

The need for collection of reliability, maintainability, and availability data adds a new dimension to the data acquisition requirements of equipment development tests. This report describes the reliability and maintainability data that are considered necessary to ensure that sufficient and high quality data exist for a comprehensive, quantitative evaluation of equipment and system availability. These necessary data are presented as a set of data collection forms. Three data acquisition forms are discussed: an inventory and technical data form, which is filed by the design engineer when the design is finished or the equipment is received; an event report form, which is completed by the senior test operator at each shutdown; and a maintainability report, which is a collaborative effort between senior operators and lead engineers and is completed on restart. In addition, elements of a reliability, maintainability evaluation program are described. Emphasis is placed on the role of data, its storage, and use in such a program

Emergency Response Equipment and Related Training: Airborne Radiological Computer System (Model II)

Energy Technology Data Exchange (ETDEWEB)

David P. Colton

2007-02-28

The materials included in the Airborne Radiological Computer System, Model-II (ARCS-II) were assembled with several considerations in mind. First, the system was designed to measure and record the airborne gamma radiation levels and the corresponding latitude and longitude coordinates, and to provide a first overview look of the extent and severity of an accident's impact. Second, the portable system had to be light enough and durable enough that it could be mounted in an aircraft, ground vehicle, or watercraft. Third, the system must control the collection and storage of the data, as well as provide a real-time display of the data collection results to the operator. The notebook computer and color graphics printer components of the system would only be used for analyzing and plotting the data. In essence, the provided equipment is composed of an acquisition system and an analysis system. The data can be transferred from the acquisition system to the analysis system at the end of the data collection or at some other agreeable time.

Development of a Test Equipment for Performance Evaluation of Safety Systems

International Nuclear Information System (INIS)

Kim, S. J.; Kwon, S. M.; Lee, J. M.; Kim, C. K.; Cho, C. H.; Chun, J. H.; Park, M. K.

2004-07-01

The purpose of this study is to develop a test equipment for performance evaluation of safety systems in nuclear power plants. First, we develop an input-output simulator for reactor protection systems, ESF component control systems, and a data acquisition system for these I/O simulators as a hardware for this equipment. Then, we develop a software for human-machine interface system, which is easy-to-use and easy-to-modify. In addition, a simulation tool for a reactor trip switch gear is developed

The emerging nuclear suppliers and nonproliferation

International Nuclear Information System (INIS)

Potter, W.C.

1990-01-01

The number of states capable of exporting nuclear material, technology, equipment, and services is large and growing. Once confined primarily to states party to the Nuclear Non-Proliferation Treaty (NPT), the list of actual and potential nuclear suppliers now includes many countries that do not subscribe to the NPT or to other international nuclear export control agreements. Although international control accords---such as the Nuclear Exporters' (Zangger) Committee and the London Nuclear Suppliers Group (NSG) guidelines---do not prohibit the export of sensitive nuclear materials and equipment, they do reduce the risks of proliferation by imposing international safeguards as a condition for export. The purpose of this book---the culmination of one phase of an ongoing international research project on the emerging nuclear suppliers and nonproliferation---is to remedy, at least in part, this data deficiency

Overall Equipment Effectiveness Implementation Criteria

Science.gov (United States)

Abramova, I. G.; Abramov, D. A.

2018-01-01

This article documents the methods applied in production control technics specifically focused on commonly used parameter OEE (Overall Equipment Effectiveness). The indicators of extensive and intensive use of equipment are considered. Their appointment this is comparison in the same type of production within the industry and comparison of single-type and / or different types of equipment in terms of capacity. However, it is shown that there is no possibility of revealing the reasons for the machine’s operation: productive / unproductive, with disturbances. Therefore, in the article reveals the approaches to calculating the indicator characterizing the direct operation of the equipment. The Machine Load coefficient is approaching closely to the indicator of the efficiency of the use of equipment. Methods analysis is proceeded through the historically applied techniques such as “Stopwatch” and “Motion” studies. Was performed the analysis of the efficiency index of OEE equipment using the comparable indexes performance of equipment in the Russian practice. An important indicator of OEE contains three components. The meaning of each of them reflects historically applicable indicators. The value of the availability of equipment indicator is close to the value of the equipment extensibility index. The value of the indicator of the efficiency of work can be compared with the characteristic of the capacity of the equipment and the indicator of the quality level can meet the requirements for compliance with the manufacturing technology. Shown that the sum of the values of the coefficient of “Availability” of the equipment and the value of the “Factor of compaction of working hours” are one. As well as the total value of the indicator “level of quality” and the coefficient of marriage given in the result unit. The measurability of the indicators makes it possible to make a prediction about efficiency of the equipment.

The influence of experiential learning on medical equipment adoption in general practices.

Science.gov (United States)

Bourke, Jane; Roper, Stephen

2014-10-01

The benefits of the availability and use of medical equipment for medical outcomes are understood by physicians and policymakers alike. However, there is limited understanding of the decision-making processes involved in adopting and using new technologies in health care organisations. Our study focuses on the adoption of medical equipment in Irish general practices which are marked by considerable autonomy in terms of commercial practice and the range of medical services they provide. We examine the adoption of six items of medical equipment taking into account commercial, informational and experiential stimuli. Our analysis is based on primary survey data collected from a sample of 601 general practices in Ireland on practice characteristics and medical equipment use. We use a multivariate Probit to identify commonalities in the determinants of the adoption. Many factors, such as GP and practice characteristics, influence medical equipment adoption. In addition, we find significant and consistent evidence of the influence of learning-by-using effects on the adoption of medical equipment in a general practice setting. Knowledge generated by experiential or applied learning can have commercial, organisational and health care provision benefits in small health care organisations. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Chapter 12. Space Heating Equipment

Energy Technology Data Exchange (ETDEWEB)

Rafferty, Kevin D.

1998-01-01

The performance evaluation of space heating equipment for a geothermal application is generally considered from either of two perspectives: (a) selecting equipment for installation in new construction, or (b) evaluating the performance and retrofit requirements of an existing system. With regard to new construction, the procedure is relatively straightforward. Once the heating requirements are determined, the process need only involve the selection of appropriately sized hot water heating equipment based on the available water temperature. It is important to remember that space heating equipment for geothermal applications is the same equipment used in non-geothermal applications. What makes geothermal applications unique is that the equipment is generally applied at temperatures and flow rates that depart significantly from traditional heating system design. This chapter presents general considerations for the performance of heating equipment at non-standard temperature and flow conditions, retrofit of existing systems, and aspects of domestic hot water heating.

Emergency medicine as a specialty in Asia.

Science.gov (United States)

Pek, Jen Heng; Lim, Swee Han; Ho, Hiu Fai; Ramakrishnan, T V; Jamaluddin, Sabariah Faizah; Mesa-Gaerlan, Faith Joan C; Tiru, Mohan; Hwang, Sung Oh; Choi, Wai-Mau; Kanchanasut, Somchai; Khruekarnchana, Pairoj; Avsarogullari, Levent; Shimazu, Takeshi; Hori, Shingo

2016-04-01

We aim to examine the similarities and differences in areas of EM development, workload, workforce, and capabilities and support in the Asia region. Emerging challenges faced by our EM community are also discussed. The National Societies for Emergency Medicine of Hong Kong, India, Japan, Malaysia, Philippines, Singapore, South Korea, Taiwan, Thailand and Turkey participated in the joint Japanese Association of Acute Medicine (JAAM) and Asian Conference of Emergency Medicine (ACEM) Special Symposium held in October 2013 at Tokyo, Japan. The findings are reviewed in this paper. Emergency medicine (EM) has over the years evolved into a distinct and recognized medical discipline requiring a unique set of cognitive, administrative and technical skills for managing all types of patients with acute illness or injury. EM has contributed to healthcare by providing effective, safe, efficient and cost-effective patient care. Integrated systems have developed to allow continuity of emergency care from the community into emergency departments. Structured training curriculum for undergraduates, and specialty training programs for postgraduates are in place to equip trainees with the knowledge and skills required for the unique practice of EM. The practice of EM still varies among the Asian countries. However, as a region, we strive to continue in our efforts to develop the specialty and improve the delivery of EM.

High Altitude Platforms for Disaster Recovery: Capabilities, Strategies, and Techniques for Emergency Telecommunications

Directory of Open Access Journals (Sweden)

Juan D. Deaton

2008-09-01

Full Text Available Natural disasters and terrorist acts have significant potential to disrupt emergency communication systems. These emergency communication networks include first-responder, cellular, landline, and emergency answering services such as 911, 112, or 999. Without these essential emergency communications capabilities, search, rescue, and recovery operations during a catastrophic event will be severely debilitated. High altitude platforms could be fitted with telecommunications equipment and used to support these critical communications missions once the catastrophic event occurs. With the ability to be continuously on station, HAPs provide excellent options for providing emergency coverage over high-risk areas before catastrophic incidents occur. HAPs could also provide enhanced 911 capabilities using either GPS or reference stations. This paper proposes potential emergency communications architecture and presents a method for estimating emergency communications systems traffic patterns for a catastrophic event.

Documents for designing the emergency system for the Temelin nuclear power plant

International Nuclear Information System (INIS)

Machek, J.; Fiser, V.

1993-12-01

The organizational structure of the emergency system at the Temelin nuclear power plant is described and the responsibilities, principal assignments and number of personnel and their qualification are outlined; these include the Emergency Staff, emergency organization of the operator shift, Technical Support Center, External Emergency Support Center, and Operating Support Center. The emergency information system to secure personnel activities in emergency situations is also described. This consists of a critical safety function display system, a post-accident monitoring system, and a post-accident sampling system. The performance of the emergency support centers, their equipment with communications and computer hardware, and the number and qualification of personnel are also dealt with. The emergency classification is as follows: anomaly, incident, accident, major accident. The information and warning system is briefly described. A decision flow-chart for the assessment of emergency situations and their classification, including the complete algorithm for classifying accidents in the accident classification system, is given in the annex. (J.B.)

Automated data system for emergency meteorological response

International Nuclear Information System (INIS)

Kern, C.D.

1975-01-01

The Savannah River Plant (SRP) releases small amounts of radioactive nuclides to the atmosphere as a consequence of the production of radioisotopes. The potential for larger accidental releases to the atmosphere also exists, although the probability for most accidents is low. To provide for emergency meteorological response to accidental releases and to conduct research on the transport and diffusion of radioactive nuclides in the routine releases, a series of high-quality meteorological sensors have been located on towers in and about SRP. These towers are equipped with instrumentation to detect and record temperature and wind turbulence. Signals from the meterological sensors are brought by land-line to the SRL Weather Center-Analysis Laboratory (WC-AL). At the WC-AL, a Weather Information and Display (WIND) system has been installed. The WIND system consists of a minicomputer with graphical displays in the WC-AL and also in the emergency operating center (EOC) of SRP. In addition, data are available to the system from standard weat []er teletype services, which provide both routine surface weather observations and routine upper air wind and temperature observations for the southeastern United States. Should there be an accidental release to the atmosphere, available recorded data and computer codes would allow the calculation and display of the location, time, and downwind concentration of the atmospheric release. These data are made available to decision makers in near real-time to permit rapid decisive action to limit the consequences of such accidental releases. (auth)

41 CFR 105-71.132 - Equipment.

Science.gov (United States)

2010-07-01

.... (4) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be... managing equipment (including replacement equipment), whether acquired in whole or in part with grant funds... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Equipment. 105-71.132...

[Cirurgia Taurina--emergency medical treatment of bullfighters in Spain].

Science.gov (United States)

Lehmann, V; Lehmann, J

2003-08-01

A considerable risk of life-threatening injury is inherent to bullfighting. Thus, a unique form of emergency treatment has evolved over recent decades of organized bull-fighting. Today bullfight arenas in larger cities are equipped with emergency facilities including fully furnished operating rooms. During a fiesta these facilities are run by a medical team consisting of three surgeons, one intensive care specialist, and one anesthesiologist with their supporting medical personnel. In smaller arenas or villages immediate care units consist of emergency vehicles, and a mobile container equipped with a fully functional operating room. Of all toreros the matadores including the novilleros are most often injured in 56 % of cases. This rate decreases for banderillos (30 %), and for picadores (14 %). Parts of the body that are most frequently affected are thighs, and the inguinal region (54 %). Head and neck injuries are seen in 19 %, and 12 % of cases present with open abdominal wounds including liver or gastrointestinal tract traumas. 10 % of injuries affect the thorax, and 4 % the pelvic floor. The particular form of organised medical treatment for bullfighters in Spain has only developed since the nineteen-thirties. In 1972 a scientific society for bullfight surgery was founded in Spain by specialized surgeons, and immediate care specialists holding a first convention that year. The society is continuously striving to improve technical and logistical aspects of immediate medical care for injured bullfighters.

Comparison and Analysis of IEEE 344 and IEC 60980 standards for harmonization of seismic qualification of safety-related equipment

International Nuclear Information System (INIS)

Lee, Young Ok; Kim, Jong Seog; Seo, Jeong Ho; Kim, Myung Jun

2011-01-01

The seismic qualification of safety related equipment in nuclear power plants should demonstrate an equipment's ability to perform its safety function during/or after the time it is subjected to the forces resulting from one SSE. In addition, the equipment must withstand the effects of a number of OBEs, preceding the SSE. IEEE 344 and IEC 60980 present the criteria for establishing procedures demonstrating that the Class 1E equipment can meet its performance requirement during seismic events. Currently, IEEE 344 is used for regulation of nuclear power plant in the United State whereas IEC 60980 is mainly used in Europe. In particular, NPPs of France and China apply with RCC-E and GB that are domestic standards, respectively. Equipment supplier and Utility have difficulties because of different applicable standards. Equipment supplier to export S/R components/equipment to other standard area performs additional seismic qualification. For example, equipment are qualifies according to IEC 60980, RCC-E, GB although they have been qualified in accordance with IEEE 344. Also, utility to attempt power up-rate, life extension of NPP constructed under rules of RCC-E such as Ulchin NPP 1 and 2 has similar difficulties. RCC-E endorses IEC 60980 and GB is almost same as IEC 60980 except minor difference of earthquake environment definition. Therefore this paper surveys the similarities and differences between IEEE 344 and IEC 60980. In addition, this paper considers how the two sets of standards may be used in a complementary fashion to be possible using one or the other standard area

Emerging Technologies in the Built Environment: Geographic Information Science (GIS), 3D Printing, and Additive Manufacturing

Energy Technology Data Exchange (ETDEWEB)

New, Joshua Ryan [ORNL

2014-01-01

Abstract 1: Geographic information systems emerged as a computer application in the late 1960s, led in part by projects at ORNL. The concept of a GIS has shifted through time in response to new applications and new technologies, and is now part of a much larger world of geospatial technology. This presentation discusses the relationship of GIS and estimating hourly and seasonal energy consumption profiles in the building sector at spatial scales down to the individual parcel. The method combines annual building energy simulations for city-specific prototypical buildings and commonly available geospatial data in a GIS framework. Abstract 2: This presentation focuses on 3D printing technologies and how they have rapidly evolved over the past couple of years. At a basic level, 3D printing produces physical models quickly and easily from 3D CAD, BIM (Building Information Models), and other digital data. Many AEC firms have adopted 3D printing as part of commercial building design development and project delivery. This presentation includes an overview of 3D printing, discusses its current use in building design, and talks about its future in relation to the HVAC industry. Abstract 3: This presentation discusses additive manufacturing and how it is revolutionizing the design of commercial and residential facilities. Additive manufacturing utilizes a broad range of direct manufacturing technologies, including electron beam melting, ultrasonic, extrusion, and laser metal deposition for rapid prototyping. While there is some overlap with the 3D printing talk, this presentation focuses on the materials aspect of additive manufacturing and also some of the more advanced technologies involved with rapid prototyping. These technologies include design of carbon fiber composites, lightweight metals processing, transient field processing, and more.

Environmental Monitoring Techniques and Equipment related to the installation and operation of Marine Energy Conversion Systems

International Nuclear Information System (INIS)

Scanu, Sergio; Carli, Filippo Maria; Piermattei, Viviana; Bonamano, Simone; Paladini de Mendoza, Francesco; Marcelli, Marco; Peviani, Maximo Aurelio; Dampney, Keith; Norris, Jennifer

2015-01-01

Results of activities under project Marine Renewables Infrastructure Network for Emerging Energy Technologies (MaRINET) are reported, which led to DEMTE, a database, created on the basis of standardized monitoring of the marine environment during installation, operation and decommissioning of Marine Energy Conversion Systems. Obtained with the consortium partners’ available techniques and equipment, the database shows that such instruments cover all identified marine environmental compartments, despite the lack of underwater vehicles and the reduced skills in using satellite technologies. These weaknesses could be overcome by an accurate planning of equipment, techniques and knowledge sharing. The approach here presented also leads to an effective analysis even in non-marine contexts

The impact of emergency obstetric care training in Somaliland, Somalia.

Science.gov (United States)

Ameh, Charles; Adegoke, Adetoro; Hofman, Jan; Ismail, Fouzia M; Ahmed, Fatuma M; van den Broek, Nynke

2012-06-01

To provide and evaluate in-service training in "Life Saving Skills - Emergency Obstetric and Newborn Care" in order to improve the availability of emergency obstetric care (EmOC) in Somaliland. In total, 222 healthcare providers (HCPs) were trained between January 2007 and December 2009. A before-after study was conducted using quantitative and qualitative methods to evaluate trainee reaction and change in knowledge, skills, and behavior, in addition to functionality of healthcare facilities, during and immediately after training, and at 3 and 6 months post-training. The HCPs reacted positively to the training, with a significant improvement in 50% of knowledge and 100% of skills modules assessed. The HCPs reported improved confidence in providing EmOC. Basic and comprehensive EmOC healthcare facilities provided 100% of expected signal functions-compared with 43% and 56%, respectively, at baseline-with trained midwives performing skills usually performed by medical doctors. Lack of drugs, supplies, medical equipment, and supportive policy were identified as barriers that could contribute to nonuse of new skills and knowledge acquired. The training impacted positively on the availability and quality of EmOC and resulted in "up-skilling" of midwives. Copyright © 2012 International Federation of Gynecology and Obstetrics. Published by Elsevier Ireland Ltd. All rights reserved.

1968 Listing of Swimming Pool Equipment.

Science.gov (United States)

National Sanitation Foundation, Ann Arbor, MI. Testing Lab.

An up-to-date listing of swimming pool equipment including--(1) companies authorized to display the National Sanitation Foundation seal of approval, (2) equipment listed as meeting NSF swimming pool equipment standards relating to diatomite type filters, (3) equipment listed as meeting NSF swimming pool equipment standard relating to sand type…

Ontario Power Generation Fukushima emergency response drill strengthens and lessons learned - Ontario Power Generation Fukushima Emergency Response Drill Highlights

International Nuclear Information System (INIS)

Miller, David W.

2014-01-01

Japan's Fukushima Daiichi severe nuclear accident in March 2011 has resulted in a reassessment of nuclear emergency response and preparedness in Canada. On May 26, 27 and 28, 2014 Ontario Power Generation (OPG) conducted the first North American full scale nuclear emergency response exercise designed to include regional, provincial and federal bodies as well as the utility. This paper describes the radiological aspects of the OPG Exercise Unified Response (ExUR) with emphasis on deployment of new Fukushima equipment on the Darlington site, management of emergency workers deplored in the vicinity of Darlington to collect environmental samples and radiation measurements, performance of dose calculations, communication of dose projections and protective actions to local, provincial and federal agencies and conduct of vehicle, truck and personnel monitoring and decontamination facilities. The ExUR involved more than 1000 personnel from local, provincial and federal bodies. Also, 200 OPG employees participated in the off-site emergency response duties. The objective of the ExUR was to test and enhance the preparedness of the utility (OPG), government and non-government agencies and communities to respond to a nuclear emergency. The types of radiological instrumentation and mobile facilities employed are highlighted in the presentation. The establishment of temporary emergency rooms with 8 beds and treatment facilities to manage potentially contaminated injuries from the nuclear emergency is also described. (author)

Satellite communication system for emergency monitoring within the Chernobyl exclusion zone

International Nuclear Information System (INIS)

Franchini, C.; Mensa, M.; Kanevsky, V.A.

1997-01-01

A Satellite Emergency Monitoring system of the Chernobyl Exclusive Zone (SEM CEZ) was designed to provide the Ukraine authorities and the neighbouring countries with updated information when an emergency situation occurs in the Exclusion Zone. This is of particular importance when environment contamination has transboundary effect. SEM system consists of mobile and fixed sensors reporting data via a dedicated satellite communications link. Mobile sensors are fitted with Global Positioning System (GPS) receivers that determine current coordinates of the sensor. Sensors data are transmitted to the Emergency Monitoring Centre equipped with PC and a satellite terminal. Both sensors data and the current position are visualized on digital maps

Annual report of Nuclear Emergency Assistance and Training Center. April 1, 2013 - March 31, 2014

International Nuclear Information System (INIS)

Sato, Takeshi; Muto, Shigeo; Akiyama, Kiyomitsu; Aoki, Kazufumi; Okamoto, Akiko; Kawakami, Takeshi; Kume, Nobuhide; Nakanishi, Chika; Koie, Masahiro; Kawamata, Hiroyuki; Nemotouchi, Toshimasa; Saito, Toru; Kato, Tadashi; Sumiya, Akio; Yamamoto, Kazuya; Sato, Sohei; Sumiya, Akihiro; Okuno, Hiroshi; Yoshida, Hiroshi; Kikuchi, Masayuki; Matsusaka, Masaru

2015-02-01

The Japan Atomic Energy Agency, which will be abbreviated as JAEA hereafter, was assigned as a designated public institution under the Disaster Countermeasures Basic Act and under the Armed Attack Situations Response Act. Based on these Acts, the JAEA has the responsibility of providing technical support to the national government and/or local governments in case of disaster responses or response in the event of a military attack, etc. In order to fulfill the tasks, the JAEA has established the Emergency Action Plan and the Civil Protection Action Plan. In case of a nuclear emergency, the Nuclear Emergency Assistance and Training Center (NEAT) dispatches specialists of JAEA, supplies the national government and local governments with emergency equipment and materials, and gives technical advice and information. In normal time, NEAT provides various exercises and training courses concerning nuclear disaster prevention to those personnel taking an active part in emergency response institutions of the national and local governments, police, fire fighters, self-defense forces, etc. in addition to the JAEA itself. The NEAT also researches nuclear disaster preparedness and response, and cooperates with international organizations. In the FY2013, the NEAT accomplished the following tasks: (1) Technical support activities as a designated public institution in cooperation with the national and local governments, etc. (2) Human resource development, exercise and training of nuclear emergency response personnel for the national and local governments, etc. (3) Researches on nuclear disaster preparedness and response, and sending useful information. (4) International contributions to Asian countries on nuclear disaster preparedness and response in collaboration with the international organizations. (author)

14 CFR Appendix D to Part 121 - Criteria for Demonstration of Emergency Evacuation Procedures Under § 121.291

Science.gov (United States)

2010-01-01

... against shining into the airplane's windows or doors. (2) The airplane must be a normal ground attitude with landing gear extended. (3) Unless the airplane is equipped with an off-wing descent means, stands... is not part of the emergency evacuation equipment of the airplane may be used to aid the participants...

Initiatives to Improve Quality of Additively Manufactured Parts

Science.gov (United States)

Waller, Jess; Nichols, Charles

2017-01-01

NASA is providing leadership in an international effort linking government and industry resources to speed adoption of additive manufactured (AM) parts. Participants include government agencies (NASA, USAF, NIST, FAA), industry (commercial aerospace, NDE manufacturers, AM equipment manufacturers), standards organizations and academia. NASA is also partnering with its international space exploration organizations such as ESA and JAXA. NDT is identified as a universal need for all aspects of additive manufacturing.

29 CFR 1926.952 - Mechanical equipment.

Science.gov (United States)

2010-07-01

... equipment that are not covered with insulating protective equipment. (c) Derrick trucks, cranes and other lifting equipment. (1) All derrick trucks, cranes and other lifting equipment shall comply with subpart N...

Technical diagnostics - equipment monitoring for increasing safety and availability of nuclear power plants

International Nuclear Information System (INIS)

Sturm, A.; Foerster, R.

1977-01-01

Utilization of technical diagnostics in equipment monitoring of nuclear power plants for ensuring nuclear safety, economic availability, and for decision making on necessary maintenance is reviewed. Technical diagnostics is subdivided into inspection and early detection of malfunctions. Moreover, combination of technical diagnostics and equipment monitoring, integration of technical diagnostics into maintenance strategy, and problems of introducing early detection of malfunctions into maintenance management of nuclear power plants are also discussed. In addition, a compilation of measuring techniques used in technical diagnostics has been made. The international state of the art of equipment monitoring in PWR nuclear power plants is illustrated by description of the sound and vibration measuring techniques. (author)

Assessment of the performance of containment and surveillance equipment part 1: methodology

International Nuclear Information System (INIS)

Rezniczek, A.; Richter, B.

2009-01-01

Equipment performance aims at the creation of relevant data. As Containment and Surveillance (C/S) is playing an ever increasing role in safeguards systems, the issue of how to assess the performance of C/S equipment is being addressed by the ESARDA Working Group on C/S. The issue is important not only for the development of appropriate safeguards approaches but also for the review of existing approaches with regard to the implementation of the Additional Protocol (A P) and Integrated Safeguards. It is expected that the selection process of appropriate equipment, especially for unattended operation, is facilitated by the availability of methods to determine the performance of such equipment. Apart from EURATOM, the users of assessment methodologies would be the International Atomic Energy Agency (IAEA), plant operators, and instrument developers. The paper describes a non-quantitative performance assessment methodology. A structured procedure is outlined that allows assessing the suitability of different C/S instrumentation to comply with the objectives of its application. The principle to determine the performance of C/S equipment is to define, based on safeguards requirements, a task profile and to check the performance profile against the task profile. The performance profile of C/S equipment can be derived from the functional specifications and design basis tolerances provided by the equipment manufacturers.

Benefits Of Vibration Analysis For Development Of Equipment In HLW Tanks - 12341

International Nuclear Information System (INIS)

Stefanko, D.; Herbert, J.

2012-01-01

Vibration analyses of equipment intended for use in the Savannah River Site (SRS) radioactive liquid waste storage tanks are performed during pre-deployment testing and has been demonstrated to be effective in reducing the life-cycle costs of the equipment. Benefits of using vibration analysis to identify rotating machinery problems prior to deployment in radioactive service will be presented in this paper. Problems encountered at SRS and actions to correct or lessen the severity of the problem are discussed. In short, multi-million dollar cost saving have been realized at SRS as a direct result of vibration analysis on existing equipment. Vibration analysis of equipment prior to installation can potentially reduce inservice failures, and increases reliability. High-level radioactive waste is currently stored in underground carbon steel waste tanks at the United States Department of Energy (DOE) Savannah River Site and at the Hanford Site, WA. Various types of rotating machinery (pumps and separations equipment) are used to manage and retrieve the tank contents. Installation, maintenance, and repair of these pumps and other equipment are expensive. In fact, costs to remove and replace a single pump can be as high as a half million dollars due to requirements for radioactive containment. Problems that lead to in-service maintenance and/or equipment replacement can quickly exceed the initial investment, increase radiological exposure, generate additional waste, and risk contamination of personnel and the work environment. Several different types of equipment are considered in this paper, but pumps provide an initial example for the use of vibration analysis. Long-shaft (45 foot long) and short-shaft (5-10 feet long) equipment arrangements are used for 25-350 horsepower slurry mixing and transfer pumps in the SRS HLW tanks. Each pump has a unique design, operating characteristics and associated costs, sometimes exceeding a million dollars. Vibration data are routinely

BENEFITS OF VIBRATION ANALYSIS FOR DEVELOPMENT OF EQUIPMENT IN HLW TANKS - 12341

Energy Technology Data Exchange (ETDEWEB)

Stefanko, D.; Herbert, J.

2012-01-10

Vibration analyses of equipment intended for use in the Savannah River Site (SRS) radioactive liquid waste storage tanks are performed during pre-deployment testing and has been demonstrated to be effective in reducing the life-cycle costs of the equipment. Benefits of using vibration analysis to identify rotating machinery problems prior to deployment in radioactive service will be presented in this paper. Problems encountered at SRS and actions to correct or lessen the severity of the problem are discussed. In short, multi-million dollar cost saving have been realized at SRS as a direct result of vibration analysis on existing equipment. Vibration analysis of equipment prior to installation can potentially reduce inservice failures, and increases reliability. High-level radioactive waste is currently stored in underground carbon steel waste tanks at the United States Department of Energy (DOE) Savannah River Site and at the Hanford Site, WA. Various types of rotating machinery (pumps and separations equipment) are used to manage and retrieve the tank contents. Installation, maintenance, and repair of these pumps and other equipment are expensive. In fact, costs to remove and replace a single pump can be as high as a half million dollars due to requirements for radioactive containment. Problems that lead to in-service maintenance and/or equipment replacement can quickly exceed the initial investment, increase radiological exposure, generate additional waste, and risk contamination of personnel and the work environment. Several different types of equipment are considered in this paper, but pumps provide an initial example for the use of vibration analysis. Long-shaft (45 foot long) and short-shaft (5-10 feet long) equipment arrangements are used for 25-350 horsepower slurry mixing and transfer pumps in the SRS HLW tanks. Each pump has a unique design, operating characteristics and associated costs, sometimes exceeding a million dollars. Vibration data are routinely

Comparison of safety equipment between London underground and Beijing subway

Science.gov (United States)

Chen, T.; Zhang, S. Y.; Zhao, L. Z.; Xia, J. J.; Fu, X. C.; Bao, Z. M.; Chen, Y.; Zhang, X. Z.; Wang, R. J.; Hu, C.; Jing, L. S.; Wang, Y.

2017-06-01

The purpose of this paper was to improve the safety equipment’s effectiveness through the comparison. Firstly, the history and safety accident of London Underground and Beijing Subway were shown. Secondly, fire equipment between these two cities was compared including station’s hardware installations and carriage’s hardware installations. Thirdly, the relative software installations were also compared such as emergency drills. The results showed that Beijing Subway’s hardware installations were better than London. However, London Underground’s some installations were more effective than Beijing. Both cities would pay more attention on anti-terrorist in tunnel.

Equipment Operational Requirements

Energy Technology Data Exchange (ETDEWEB)

Greenwalt, B; Henderer, B; Hibbard, W; Mercer, M

2009-06-11

The Iraq Department of Border Enforcement is rich in personnel, but poor in equipment. An effective border control system must include detection, discrimination, decision, tracking and interdiction, capture, identification, and disposition. An equipment solution that addresses only a part of this will not succeed, likewise equipment by itself is not the answer without considering the personnel and how they would employ the equipment. The solution should take advantage of the existing in-place system and address all of the critical functions. The solutions are envisioned as being implemented in a phased manner, where Solution 1 is followed by Solution 2 and eventually by Solution 3. This allows adequate time for training and gaining operational experience for successively more complex equipment. Detailed descriptions of the components follow the solution descriptions. Solution 1 - This solution is based on changes to CONOPs, and does not have a technology component. It consists of observers at the forts and annexes, forward patrols along the swamp edge, in depth patrols approximately 10 kilometers inland from the swamp, and checkpoints on major roads. Solution 2 - This solution adds a ground sensor array to the Solution 1 system. Solution 3 - This solution is based around installing a radar/video camera system on each fort. It employs the CONOPS from Solution 1, but uses minimal ground sensors deployed only in areas with poor radar/video camera coverage (such as canals and streams shielded by vegetation), or by roads covered by radar but outside the range of the radar associated cameras. This document provides broad operational requirements for major equipment components along with sufficient operational details to allow the technical community to identify potential hardware candidates. Continuing analysis will develop quantities required and more detailed tactics, techniques, and procedures.

Bilateral tension pneumothorax following equipment improvisation.

Science.gov (United States)

Zambricki, Christine; Schmidt, Carol; Vos, Karen

2014-02-01

This case report describes an unexpected event that took place as a result of using improvised equipment. The patient, a 16-year-old female undergoing complex oral surgery, suffered bilateral pneumothorax following the improper use of an airway support device. During the immediate postoperative period with the patient still intubated, oxygen tubing was attached to a right angle elbow connector with the port closed and 10 L/minute oxygen flow was administered to the patient in a manner that did not allow the patient to exhale. Within seconds, pneumothorax was apparent as the patient's vital signs deteriorated, visible swelling was noted in the shoulders and neck, and there was an absence of breath sounds on auscultation. This case study has application beyond the immediate discussion of bilateral pneumothorax, serving as a caution about the unintended consequences of equipment improvisation. In addition to highlighting the hazards of providing patient care with a non-standard device, this study also provides a powerful example of the human factors that can contribute to medical errors in the healthcare setting.

Characterization equipment essential drawing plan

International Nuclear Information System (INIS)

WILSON, G.W.

1999-01-01

The purpose of this document is to list the Characterization equipment drawings that are classified as Essential Drawings. Essential Drawings: Are those drawings identified by the facility staff as necessary to directly support the safe operation of the facility or equipment (HNF 1997a). The Characterization equipment drawings identified in this report are deemed essential drawings as defined in HNF-PRO-242, Engineering Drawing Requirements (HNF 1997a). These drawings will be prepared, revised, and maintained per HNF-PRO-440, Engineering Document Change Control (HNF 1997b). All other Characterization equipment drawings not identified in this document will be considered Support drawings until the Characterization Equipment Drawing Evaluation Report is completed

Modeling Manpower and Equipment Productivity in Tall Building Construction Projects

Science.gov (United States)

Mudumbai Krishnaswamy, Parthasarathy; Rajiah, Murugasan; Vasan, Ramya

2017-12-01

Tall building construction projects involve two critical resources of manpower and equipment. Their usage, however, widely varies due to several factors affecting their productivity. Currently, no systematic study for estimating and increasing their productivity is available. What is prevalent is the use of empirical data, experience of similar projects and assumptions. As tall building projects are here to stay and increase, to meet the emerging demands in ever shrinking urban spaces, it is imperative to explore ways and means of scientific productivity models for basic construction activities: concrete, reinforcement, formwork, block work and plastering for the input of specific resources in a mixed environment of manpower and equipment usage. Data pertaining to 72 tall building projects in India were collected and analyzed. Then, suitable productivity estimation models were developed using multiple linear regression analysis and validated using independent field data. It is hoped that the models developed in the study will be useful for quantity surveyors, cost engineers and project managers to estimate productivity of resources in tall building projects.

Cervical spine alignment in the youth football athlete: recommendations for emergency transportation.

Science.gov (United States)

Treme, Gehron; Diduch, David R; Hart, Jennifer; Romness, Mark J; Kwon, Michael S; Hart, Joseph M

2008-08-01

Substantial literature exists regarding recommendations for the on-field treatment and subsequent transportation of adult collision-sport athletes with a suspected injury to the cervical spine. To develop an evidence-based recommendation for transportation of suspected spine-injured youth football players. Descriptive laboratory study. Three lateral radiographs were obtained in supine to include the occiput to the cervical thoracic junction from 31 youth football players (8-14 years). Each child was imaged while wearing helmet and shoulder pads, without equipment, and with shoulder pads only. Two independent observers measured cervical spine angulation as Cobb angle from C1 to C7 and subaxial angulation from C2 to C7. We calculated intraclass correlation coefficients for intraobserver reliability analysis and compared Cobb and C2 to C7 angles between equipment conditions with t tests. Interobserver analysis showed excellent reliability among measurements. Cobb and subaxial angle measurements indicated significantly greater cervical lordosis while children wore shoulder pads only, compared with the other 2 conditions (no equipment and helmet and shoulder pads) (P .05). Equipment removal for the youth football athlete with suspected cervical spine injury should abide by the "all or none" policy that has been widely accepted for adult athletes. Helmet and shoulder pads should be left in place during emergency transport of the suspected spine-injured youth athlete. Despite differences in head to torso size ratios between youth and adult players, helmet removal alone is not recommended for either during emergency transportation.

High Altitude Platforms for Disaster Recovery: Capabilities, Strategies, and Techniques for Emergency Telecommunications

Directory of Open Access Journals (Sweden)

Deaton JuanD

2008-01-01

Full Text Available Abstract Natural disasters and terrorist acts have significant potential to disrupt emergency communication systems. These emergency communication networks include first-responder, cellular, landline, and emergency answering services such as 911, 112, or 999. Without these essential emergency communications capabilities, search, rescue, and recovery operations during a catastrophic event will be severely debilitated. High altitude platforms could be fitted with telecommunications equipment and used to support these critical communications missions once the catastrophic event occurs. With the ability to be continuously on station, HAPs provide excellent options for providing emergency coverage over high-risk areas before catastrophic incidents occur. HAPs could also provide enhanced 911 capabilities using either GPS or reference stations. This paper proposes potential emergency communications architecture and presents a method for estimating emergency communications systems traffic patterns for a catastrophic event.

The role of the Swiss EIR Health Physics Division in the national and the Institute's radiological emergency organizations

International Nuclear Information System (INIS)

Nagel, E.; Brunner, H.

1986-01-01

Owing to the geographical concentration in Switzerland of the activities related to radioactivity (power plants, research, industry, transport) in a relatively small region between the Alps and the Rhine, it was a logical consequence to centralize the emergency organization for nuclear accidents in this area. Since 1984 the Swiss emergency organization has had an operational, well-equipped national emergency control centre. In the handling of radiation accidents the new organization can call on specialized laboratories and make use of experience and material from over the whole country. Of these facilities the Federal Institute for Reactor Research (EIR) is of major importance due to its activities and experience in research and radiation protection. Its Health Physics Division takes an active part in the emergency organization of the EIR itself. Both its well-equipped radioanalytical laboratory and trained personnel are at the disposal of the national emergency organization. Frequent training of the whole emergency organization and parts of it have improved preparedness. The evaluation of the exercises always reveals new problems to be solved in which rapid action and safe communications are of major importance. (author)

An introduction to closed field sputtering (CFS) equipment

International Nuclear Information System (INIS)

Sugden, G.B.

1979-01-01

Ways have been sought to develop the vacuum sputtering process to reduce the source material temperature and to increase the deposition rate. A new industrial plating method superior to vacuum evaporation and electroplating has emerged. In this 'closed field sputtering' processes an electric field is applied between a coaxial anode and cathode and a magnetic field applied orthogonally to the electric field. Providing the flux density of the magnetic field is above a critical value no electrons flow to the anode but move along the magnetic lines around the cathode, enclosed in the magnetic field. A high density electron cloud with high ionization probability is therefore maintained. Low temperature sputtering can be attained due to very low energy loss of electrons at the anode. A pressure of about (2-5) x 10(-4) torr is used. High power can be applied to the equipment without producing much heat. It enables a large number of plastic parts to be coated with almost any nonmagnetic metal and alloys of metals on a commercial basis. It is also possible to produce coatings of oxides. nitrides and carbides of metals. The method of operation and a description of the equipment are given. Applications include car exteriors, household appliances, furniture toys and the electronics industry. (UK)

Evolution of Additively Manufactured Injection Molding Inserts Investigated by Thermal Simulations

DEFF Research Database (Denmark)

Hofstätter, Thomas; Pedersen, David B.; Tosello, Guido

Injection molding using inserts from vat polymerization, an additive manufacturing technology, has been investigated for pilot production and rapid prototyping purposes throughout the past years. A standard mold is equipped with additively manufactured inserts in a rectangular shape of (20 x 20 x 2...

Ageing management and equipment qualification

International Nuclear Information System (INIS)

Stahl, Gunnar

2014-01-01

The knowledge of how the environment and load of organic material in general and especially polymers and lubricants, is affecting the degradation of important properties, have increased during the last decade. However the restrictions using established additives like some color pigments due to their poisonousness e.g. pigments based at cadmium, lead, mercury etc. have caused problems when replacing additives to polymers. The replacement additives have often been used in new design without going through the required material qualification procedure. There have also been observed that some non-qualified and non-approved materials have been installed in some power plants due to false documentation. There are also a lot of new manufacturers, of materials similar to the previously qualified materials, active at the market. This increases the difficulty to ensure that the required material quality is used. New materials, new additives and new manufacturers makes if more and more difficult to assure that the expected material is present. This causes more strict demands of how the new materials often used in equipment at type-testing and in replacement materials are analyzed and documented. By implementing new steps for chemical, mechanical and electrical analysis and increase the general quality assurance content this issue can be managed. (authors)

Nuclear emergency preparedness and management the international nuclear emergency exercise Inex 2000

International Nuclear Information System (INIS)

Mundigl, St.

2003-01-01

With the initiation of the first international nuclear emergency exercise INEX 1, performed as a table-top exercise in 1993, the international community tested, for the first time, approaches and policies in place to manage a nuclear or radiological emergency. INEX 1 with its related workshops led to a wealth of lessons learned and to an improvement in nuclear emergency management. The INEX 2 exercise series, initiated by the NEA and performed between 1996 and 1999, established an international nuclear emergency 'exercise culture' leading to a clear improvement of the international aspects of nuclear emergency preparedness and management. INEX 2 was a series of four command post exercises based on national nuclear emergency exercises in Switzerland, Finland, Hungary and Canada. Simulated accidents at nuclear power plants were used to test existing procedures in emergency response and management, and to analyse local, regional, national and international emergency plans under realistic conditions. In addition, the exercises allowed the participating countries to gain experience using new concepts and tools. The most significant result of INEX 2 and a major step forward in nuclear emergency management was the development of a new communication and information exchange strategy, which is currently implemented by various NEA member countries as well as by the international community in general. The objective of this new strategy is to assist the decision-maker by improving the selection of the data transmitted, by encouraging the transmission and reception of such data and information using modern communication methods, e.g. secure world wide web technologies, and by defining emergency monitoring and modelling needs. To test the validity and usefulness of the newly-developed strategy, the NEA proposed to organize an international nuclear emergency exercise, INEX 2000, similar in scope to the INEX 2 exercises. In addition, the NEA suggested to include, for the first

Report on equipment availability for the ten-year period, 1966--1975

Energy Technology Data Exchange (ETDEWEB)

1976-12-01

This is an annual report of availability and outage statistics for electric power generating facilities operating in the United States. A list of utility organizations voluntarily participating in the EEI Equipment Availability Program in 1975 is located in Appendix F. All summary reports in this publication are for the 10-year period 1966-1975. Each reporting utility company has received reports on individual units for which data were submitted. Also, selected major equipment manufacturers receive copies of computer reports showing an analysis of the data for their equipment. Revised reporting instructions to incorporate Safety and Environmental Requirement Cause Codes were issued effective January 1, 1976. In addition, provisions were made for identifying major equipment manufactured outisde of the United States or under foreign license. Recognizing that an Annual Report contains only a limited amount of general outage data in selected categories, the Task Force has agreed to perform special analyses of the data bank if the cost of computer services is met by the requestor and if the required analysis conforms to some designated policy guidelines.

CRNL research reactor retrofit Emergency Filtration System

International Nuclear Information System (INIS)

Philippi, H.M.

1990-01-01

This paper presents a brief history of NRX and NRU research reactor effluent air treatment systems before describing the selection and design of an appropriate retrofit Emergency Filtration System (EFS) to serve these reactors and the future MX-10 isotope production reactor. The conceptual design of the EFS began in 1984. A standby concrete shielding filter-adsorber system, sized to serve the reactor with the largest exhaust flow, was selected. The standby system, bypassed under normal operating conditions, is equipped with normal exhaust stream shutoff and diversion valves to be activated manually when an emergency is anticipated, or automatically when emergency levels of gamma radiation are detected in the exhaust stream. The first phase of the EFS installation, that is the construction of the EFS and the connection of NRU to the system, was completed in 1987. The second phase of construction, which includes the connection of NRX and provisions for the future connection of MX-10, is to be completed in 1990

The technical bases for government emergency plans

International Nuclear Information System (INIS)

Champion, D.; Herviou, K.

2006-01-01

Despite technical and organisational existing arrangements to prevent human and equipment failures, the occurrence of a severe accident inducing an important release of radioactive or toxic products could not be totally excluded. Public authorities are responsible for the development of emergency plans which main objective is the protection of the population in case of accident. The efficiency of emergency plans assumes they have been established before the occurrence of any accident, taking into account specificities of the installation and its environment. On the basis of the list of possible events likely to induce releases into the environment, some 'envelope' scenarios are selected and their consequences are assessed- The comparison of the consequences to reference levels for which protective actions are recommended gives the area where actions may be required. This approach is applied for the different nuclear facilities in France. Examples are given in the article on the definition of emergency plans technical basis for nuclear power plants, other nuclear facilities and transportation of radioactive materials. (authors)

Energy to the Edge (E2E) Equipment Assessment U.S. Army Rapid Equipping Force

Science.gov (United States)

2015-05-01

84 Contents Energy to the Edge • U.S. Army Rapid Equipping Force U.S. Army Rapid Equipping Force 1.0 Executive Summary Executive Summary U.S. Army... audiovisual equipment. • Once radiant barrier liner is inserted, the process of subsequent setups • Cables for lighting and outlets are located...behind the internal barrier • The shelter comes with organic audiovisual equipment. b. • • This shelter has a different setup and tear down process

High Altitude Platforms for Disaster Recovery: Capabilities, Strategies, and Techniques for Providing Emergency Telecommunications

Energy Technology Data Exchange (ETDEWEB)

Juan D. Deaton

2008-05-01

Natural disasters and terrorist acts have significant potential to disrupt emergency communication systems. These emergency communication networks include first-responder, cellular, landline, and emergency answering services such as 911, 112, or 999. Without these essential emergency communications capabilities, search, rescue, and recovery operations during a catastrophic event will be severely debilitated. High altitude platforms could be fitted with telecommunications equipment and used to support these critical communications missions once the catastrophic event occurs. With the ability to be continuously on station, HAPs provide excellent options for providing emergency coverage over high-risk areas before catastrophic incidents occur. HAPs could also provide enhanced 911 capabilities using either GPS or reference stations. This paper proposes potential emergency communications architecture and presents a method for estimating emergency communications systems traffic patterns for a catastrophic event.

Information technology equipment cooling method

Science.gov (United States)

Schultz, Mark D.

2015-10-20

According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools air utilized by the rack of information technology equipment to cool the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat generated by the rack of information technology equipment.

Max Tech and Beyond: Maximizing Appliance and Equipment Efficiency by Design

Energy Technology Data Exchange (ETDEWEB)

Desroches, Louis-Benoit; Garbesi, Karina

2011-07-20

It is well established that energy efficiency is most often the lowest cost approach to reducing national energy use and minimizing carbon emissions. National investments in energy efficiency to date have been highly cost-effective. The cumulative impacts (out to 2050) of residential energy efficiency standards are expected to have a benefit-to-cost ratio of 2.71:1. This project examined energy end-uses in the residential, commercial, and in some cases the industrial sectors. The scope is limited to appliances and equipment, and does not include building materials, building envelopes, and system designs. This scope is consistent with the scope of DOE's appliance standards program, although many products considered here are not currently subject to energy efficiency standards. How much energy could the United States save if the most efficient design options currently feasible were adopted universally? What design features could produce those savings? How would the savings from various technologies compare? With an eye toward identifying promising candidates and strategies for potential energy efficiency standards, the Max Tech and Beyond project aims to answer these questions. The analysis attempts to consolidate, in one document, the energy savings potential and design characteristics of best-on-market products, best-engineered products (i.e., hypothetical products produced using best-on-market components and technologies), and emerging technologies in research & development. As defined here, emerging technologies are fundamentally new and are as yet unproven in the market, although laboratory studies and/or emerging niche applications offer persuasive evidence of major energy-savings potential. The term 'max tech' is used to describe both best-engineered and emerging technologies (whichever appears to offer larger savings). Few best-on-market products currently qualify as max tech, since few apply all available best practices and components. The

Equipment abnormality monitoring device

International Nuclear Information System (INIS)

Ando, Yasumasa

1991-01-01

When an operator hears sounds in a plantsite, the operator compares normal sounds of equipment which he previously heard and remembered with sounds he actually hears, to judge if they are normal or abnormal. According to the method, there is a worry that abnormal conditions can not be appropriately judged in a case where the number of objective equipments is increased and in a case that the sounds are changed gradually slightly. Then, the device of the present invention comprises a plurality of monitors for monitoring the operation sound of equipments, a recording/reproducing device for recording and reproducing the signals, a selection device for selecting the reproducing signals among the recorded signals, an acoustic device for converting the signals to sounds, a switching device for switching the signals to be transmitted to the acoustic device between to signals of the monitor and the recording/reproducing signals. The abnormality of the equipments can be determined easily by comparing the sounds representing the operation conditions of equipments for controlling the plant operation and the sounds recorded in their normal conditions. (N.H.)

40 CFR 31.32 - Equipment.

Science.gov (United States)

2010-07-01

... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Equipment. 31.32 Section 31.32...

14 CFR 1273.32 - Equipment.

Science.gov (United States)

2010-01-01

... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Equipment. 1273.32 Section 1273.32...

29 CFR 1470.32 - Equipment.

Science.gov (United States)

2010-07-01

... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 29 Labor 4 2010-07-01 2010-07-01 false Equipment. 1470.32 Section 1470.32 Labor Regulations...

38 CFR 43.32 - Equipment.

Science.gov (United States)

2010-07-01

... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Equipment. 43.32 Section...

Strategic project selection based on evidential reasoning approach for high-end equipment manufacturing industry

Directory of Open Access Journals (Sweden)

Lu Guangyan

2017-01-01

Full Text Available With the rapid development of science and technology, emerging information technologies have significantly changed the daily life of people. In such context, strategic project selection for high-end equipment manufacturing industries faces more and more complexities and uncertainties with the consideration of several complex criteria. For example, a group of experts rather than a single expert should be invited to select strategic project for high-end equipment manufacturing industries and the experts may feel difficulty to express their preferences towards different strategic projects due to their limited cognitive capabilities. In order to handle these complexities and uncertainties, the criteria framework of strategic project selection is firstly constructed based on the characteristics of high-end equipment manufacturing industries and then evidential reasoning (ER approach is introduced in this paper to help experts express their uncertain preferences and aggregate these preferences to generate an appropriate strategic project. A real case of strategic project selection in a high-speed train manufacturing enterprise is investigated to demonstrate the validity of the ER approach in solving strategic project selection problem.

Putting agricultural equipment and digital technologies at the cutting edge of agroecology

Directory of Open Access Journals (Sweden)

Bellon Maurel Véronique

2017-05-01

at the service of agroecology is not a straightforward route, but it is above all a real opportunity to produce better, technically and organizationally, with the emergence of new solidarities (sharing of data and knowledge. This is why it is absurd, as it is sometimes read, to oppose agroecology and technology. Agroecology is a set of practices to be built, while agro-equipment and digital technologies are a set of resources to be mobilized, with others, to achieve the objectives of sustainable agricultural production.

Common understanding of Emergency Workers

International Nuclear Information System (INIS)

2015-11-01

While the protection of Emergency Workers is regulated in most countries, national definitions, respectively interpretations differ. The prevailing regulatory frameworks are: - Basic Safety Standards (2013/59/EURATOM) The Basis Safety Standards (BSS) are binding for members of the EU. The BSS give a definition of Emergency Workers. - IAEA General Safety Requirements Part 7 (Draft). The Agency's definition is consistent with the BSS-definition. In addition, the Helper is defined. - The Nordic Flag-book. The Nordic Flag-book's Emergency Worker is consistent with the BSS-definition. In addition, workers are defined. Flag-book-Workers (FBW) are neither coterminous with GSR-P-7-helpers nor with BSS-workers. The possible need for harmonization was assessed by the means of a questionnaire, asking members of the Working Group Emergencies to attribute regulatory categories to different roles that might arise in an emergency. While showing a rich variation in interpretations, there is general agreement for the most important roles. Wherever differences are found, the bilateral impact is deemed to be marginal at worst. Therefore, no need for harmonisation with respect to the concept of Emergency Workers is seen

State of technology assessment for life extension of electrical and I and C equipment in nuclear power plants

International Nuclear Information System (INIS)

DuCharme, A.R.; Boger, R.M.; Meyer, L.C.; Beament, P.R.

1988-01-01

As part of the IEEE Working Group 3.4 on Nuclear Plant Life Extension, an assessment is made of the current state of technology for the life extension of certain classes of electrical and IandC equipment. The classes investigated include motors, cables, emergency diesel generators, penetrations, inverters/chargers, switchgear, and reactor protection systems. The work is focussed on assessment of current or recently completed RandD efforts to resolve issues affecting life extension of the equipment. Aspects discussed include the degree of resolution of these issues, potentially affected standards, and technical aspects requiring further research. 15 refs., 2 tabs

State of technology assessment for life extension of electrical and I and C equipment in nuclear power plants

International Nuclear Information System (INIS)

Du Charme, A.R.; Boger, R.M.; Meyer, L.C.; Beament, P.R.

1988-01-01

As part of the IEEE Working Group 3.4 on Nuclear Plant Life Extension, an assessment is made of the current state of technology for the life extension of certain classes of electrical and I and C equipment. The classes investigated include motors, cables, emergency diesel generators, penetrations, inverters/charges, switchgear, and reactor protection systems. The work is focussed on assessment of current or recently completed R and D efforts to resolve issues affecting life extension of the equipment. Aspects discussed include the degree of resolution of these issues, potentially affected standards, and technical aspects requiring further research

RESUME95 Nordic field test of mobile equipment for nuclear fall-out monitoring

Energy Technology Data Exchange (ETDEWEB)

Bourgeois, C.; Bresson, J.; Chiffot, T.; Guillot, L. [Centre d`Etudes de Valduc, Direction des Applications Militaires, Commissaiat a L`Energie Atomique, Tille (France)

1997-12-31

Nordic Safety Research (NKS) organised in August 1995 a field test of various techniques and instrumentation for monitoring radioactive fall-out. In an emergency situation, after a major release of radioactive material, many different measuring systems are going to be used, ranging from small hand hold intensitometer to complex spectrometer systems. In this test the following type of equipment were tested: Airborne spectrometers; Carborne spectrometers and dose rate meters; In situ spectrometers and intensitometers. Helinuc team was equipped of an airborne system and of a germanium device for in situ measurements. Different tasks were specified for each team: Mapping caesium fall-out and natural activity over two areas of 18 and 5 km{sup 2}; Research of hidden sources. For measurements and data processing the respect of time allowed was strictly controlled for testing the ability of each team. (au).

RESUME95 Nordic field test of mobile equipment for nuclear fall-out monitoring

Energy Technology Data Exchange (ETDEWEB)

Bourgeois, C; Bresson, J; Chiffot, T; Guillot, L [Centre d` Etudes de Valduc, Direction des Applications Militaires, Commissaiat a L` Energie Atomique, Tille (France)

1998-12-31

Nordic Safety Research (NKS) organised in August 1995 a field test of various techniques and instrumentation for monitoring radioactive fall-out. In an emergency situation, after a major release of radioactive material, many different measuring systems are going to be used, ranging from small hand hold intensitometer to complex spectrometer systems. In this test the following type of equipment were tested: Airborne spectrometers; Carborne spectrometers and dose rate meters; In situ spectrometers and intensitometers. Helinuc team was equipped of an airborne system and of a germanium device for in situ measurements. Different tasks were specified for each team: Mapping caesium fall-out and natural activity over two areas of 18 and 5 km{sup 2}; Research of hidden sources. For measurements and data processing the respect of time allowed was strictly controlled for testing the ability of each team. (au).

13 CFR 143.32 - Equipment.

Science.gov (United States)

2010-01-01

... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Equipment. 143.32 Section 143.32...

32 CFR 33.32 - Equipment.

Science.gov (United States)

2010-07-01

... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 32 National Defense 1 2010-07-01 2010-07-01 false Equipment. 33.32 Section 33.32 National Defense...

45 CFR 92.32 - Equipment.

Science.gov (United States)

2010-10-01

... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 45 Public Welfare 1 2010-10-01 2010-10-01 false Equipment. 92.32 Section 92.32 Public Welfare...

15 CFR 24.32 - Equipment.

Science.gov (United States)

2010-01-01

... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Equipment. 24.32 Section 24.32...

Seismic qualification of non-safety class equipment whose failure would damage safety class equipment

International Nuclear Information System (INIS)

LaSalle, F.R.

1991-01-01

Both Code of Federal Regulations, Title 10, Part 50, and US Department of Energy Order 6340.1A have requirements to assess the interaction of non-safety and safety class structures and equipment during a seismic event to maintain the safety function. At the Hanford Site, a cost effective program has been developed to perform the evaluation of non-safety class equipment. Seismic qualification is performed by analysis, test, or upgrading of the equipment to ensure the integrity of safety class structures and equipment. This paper gives a brief overview and synopsis that address design analysis guidelines including applied loading, damping values, component anchorage, allowable loads, and stresses. Test qualification of equipment and walkdown acceptance criteria for heating ampersand ventilation (H ampersand V) ducting, conduit, cable tray, missile zone of influence, as well as energy criteria are presented

Days individual equipment of protection and professional risks; Equipements de protection individuelle et risques professionnelles

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The personal protection equipment is studied in the legal way (legal liabilities, certification, European texts), technical way (ergonomics, painfulness of ventilated equipment wearing, reliability of a respirable air line, protection gloves against the chemical risk, exposure to nano particulates, working in hot area), human factors (hostile area and emotion management), studies on personal equipment such evaluation, efficiency, conception of new equipment, physiological tolerance, limit of use, and some general safety studies on the working places. (N.C.)

Composition of plastics from waste electrical and electronic equipment (WEEE) by direct sampling.

Science.gov (United States)

Martinho, Graça; Pires, Ana; Saraiva, Luanha; Ribeiro, Rita

2012-06-01

This paper describes a direct analysis study carried out in a recycling unit for waste electrical and electronic equipment (WEEE) in Portugal to characterize the plastic constituents of WEEE. Approximately 3400 items, including cooling appliances, small WEEE, printers, copying equipment, central processing units, cathode ray tube (CRT) monitors and CRT televisions were characterized, with the analysis finding around 6000 kg of plastics with several polymer types. The most common polymers are polystyrene, acrylonitrile-butadiene-styrene, polycarbonate blends, high-impact polystyrene and polypropylene. Additives to darken color are common contaminants in these plastics when used in CRT televisions and small WEEE. These additives can make plastic identification difficult, along with missing polymer identification and flame retardant identification marks. These drawbacks contribute to the inefficiency of manual dismantling of WEEE, which is the typical recycling process in Portugal. The information found here can be used to set a baseline for the plastics recycling industry and provide information for ecodesign in electrical and electronic equipment production. Copyright © 2012 Elsevier Ltd. All rights reserved.

Equipment standards for interventional cardiology

International Nuclear Information System (INIS)

Dowling, A.; Gallagher, A.; Walsh, C.; Malone, J.

2005-01-01

Interventional radiology has seen rapid growth in cardiology and represents an alternative to hazardous surgery. Recently there has been a substantial growth in the number of procedures being performed and interventional cardiology (IC) procedures are the most common interventional procedures in Europe. Advances in imaging technology have facilitated the development of increasingly complex radiological IC equipment. Currently, the technology is developing at a rate ahead of supporting research, equipment standards and a regulatory framework. International standards play a key role in the design, manufacture and performance of radiological IC equipment. A survey of 12 IC systems (15 imaging chains) was conducted in Irish hospitals. The aim of the study was to assess the imbalance between rapidly advancing technology and existing standards and to propose recommendations for new IC equipment standards. The results demonstrate the need for definitive equipment requirements and standardisation in the design, manufacture, acceptance and maintenance of IC equipment. (authors)

Communication received from the permanent mission of Austria regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material

International Nuclear Information System (INIS)

1996-01-01

The Director General received a note verbale of 13 June 1996 from Permanent Mission of Austria regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material. In the light of the request expressed at the end of the note verbale, the text of the note verbale is being circulated

Communication received from the permanent mission of Finland regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material

International Nuclear Information System (INIS)

1996-01-01

The Director General received a note verbale of 8 February 1996 from Permanent Mission of Finland regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material. In the light of the request expressed at the and of the note verbale, the text of the note verbale is being circulated

Equipment for hydraulic testing

International Nuclear Information System (INIS)

Jacobsson, L.; Norlander, H.

1981-07-01

Hydraulic testing in boreholes is one major task of the hydrogeological program in the Stripa Project. A new testing equipment for this purpose was constructed. It consists of a downhole part and a surface part. The downhole part consists of two packers enclosing two test-sections when inflated; one between the packers and one between the bottom packer and the bottom of the borehole. A probe for downhole electronics is also included in the downhole equipment together with electrical cable and nylon tubing. In order to perform shut-in and pulse tests with high accuracy a surface controlled downhole valve was constructed. The surface equipment consists of the data acquisition system, transducer amplifier and surface gauges. In the report detailed descriptions of each component in the whole testing equipment are given. (Auth.)

Multi-objective evolutionary emergency response optimization for major accidents

International Nuclear Information System (INIS)

Georgiadou, Paraskevi S.; Papazoglou, Ioannis A.; Kiranoudis, Chris T.; Markatos, Nikolaos C.

2010-01-01

Emergency response planning in case of a major accident (hazardous material event, nuclear accident) is very important for the protection of the public and workers' safety and health. In this context, several protective actions can be performed, such as, evacuation of an area; protection of the population in buildings; and use of personal protective equipment. The best solution is not unique when multiple criteria are taken into consideration (e.g. health consequences, social disruption, economic cost). This paper presents a methodology for multi-objective optimization of emergency response planning in case of a major accident. The emergency policy with regards to protective actions to be implemented is optimized. An evolutionary algorithm has been used as the optimization tool. Case studies demonstrating the methodology and its application in emergency response decision-making in case of accidents related to hazardous materials installations are presented. However, the methodology with appropriate modification is suitable for supporting decisions in assessing emergency response procedures in other cases (nuclear accidents, transportation of hazardous materials) or for land-use planning issues.

A study on the establishment of habitability requirement for enviromental laboratory in nuclear emergency

International Nuclear Information System (INIS)

Khang, Byung Oui

2003-01-01

The Establishment of the habitability requirement for Environmental Laboratory (EL) was required to decide the time of movement to a backup EL. The habitability criteria of the EL located inside plum pathway emergency planning zone was established including the alarm setpoint of the area radiation monitor based on the operational intervention level recommended by IAEA. The MDA of analysis equipments were established based on the generic action level recommended by IAEA. The countermeasures for the loss of habitability of EL was established by defined the emergency response activity at EL in nuclear emergency

An investigation of hydrogen storage methods for fuel cell operation with man-portable equipment

Energy Technology Data Exchange (ETDEWEB)

Browning, D [Defence Evaluation and Research Agency, Haslar (United Kingdom); Jones, P [Defence Evaluation and Research Agency, Haslar (United Kingdom); Packer, K [Defence Evaluation and Research Agency, Haslar (United Kingdom)

1997-03-01

Air breathing proton exchange membrane fuel cells (PEMFC) are being considered as a power source for man-portable equipment, such as army radios. In addition to the weight and volume of the fuel cell itself, the device producing hydrogen with which to fuel the cell is also of crucial importance. This paper describes a number of hydrogen storage methods and discusses their applicability to man-portable equipment. (orig.)

Shipboard and laboratory equipment

Digital Repository Service at National Institute of Oceanography (India)

Shyamprasad, M.; Ramaswamy, V.

The polymetallic nodules occur at an average depth of 4500 m. Adequate equipment and techniques are required for the exploration at such depths. Shipboard and various laboratory equipments for the sampling of polymetallic nodules is described...

Experiences in seismic upgrading of equipment and structures in Kozloduy nuclear power plant (440 WWER-PWR)

International Nuclear Information System (INIS)

Ordonez Villalobos, A.

1993-01-01

Within the framework of the 'Emergency programme for Nuclear Safety of Kozloduy NPP' it has been concluded that the increase in seismic safety of a NPP can be achieved by upgrading the key equipment in a cost effective way. Essential and vulnerable equipment has to be identified. Seismic capacity should be evaluated base don realistic state of the art criteria. Seismic review teams ef experienced engineers should conduct planned walk-downs in order to propose effective upgrading solutions. Team work of plan engineers and construction engineers would enhance the effectiveness of the solutions. It is recommended that all the participants be motivated and have a clear understanding of the objectives of the upgrading

40 CFR 792.61 - Equipment design.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Equipment design. 792.61 Section 792.61...) GOOD LABORATORY PRACTICE STANDARDS Equipment § 792.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

40 CFR 160.61 - Equipment design.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160... LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation... appropriate design and adequate capacity to function according to the protocol and shall be suitably located...

Safeguards techniques and equipment. 2003 ed

International Nuclear Information System (INIS)

2003-01-01

The 1990s saw significant non-proliferation related developments in the world, resulting in a new period of safeguards development. Over several years an assessment was made of how to strengthen the effectiveness and improve the efficiency of IAEA safeguards. In May 1997 this culminated in the adoption by the IAEA Board of Governors of a Protocol Additional to Safeguards Agreements which significantly broadens the role of IAEA safeguards. As a consequence, the IAEA safeguards system entered a new era. In 1997 the IAEA began to publish a new series of booklets on safeguards, called the International Nuclear Verification Series (NVS). The objective of these booklets was to help in explaining IAEA safeguards, especially the new developments in safeguards, particularly for facility operators and government officers involved with these topics. The current booklet, which is a revision and update of IAEA/NVS/1, is intended to give a full and balanced description of the techniques and equipment used for both nuclear material accountancy and containment and surveillance measures, and for the new safeguards measure of environmental sampling. A completely new section on data security has been added to describe the specific features that are included in installed equipment systems in order to ensure the authenticity and confidentiality of information. As new verification measures continue to be developed the material in this booklet will be periodically reviewed and updated versions issued. The basic verification measure used by the IAEA is nuclear material accountancy. In applying nuclear material accountancy, IAEA safeguards inspectors make independent measurements to verify quantitatively the amount of nuclear material presented in the State's accounts. For this purpose, inspectors count items (e.g. fuel assemblies, bundles or rods, or containers of powdered compounds of uranium or plutonium) and measure attributes of these items during their inspections using non

Equipment installation structure of roof slab for tank type FBR and method of equipment installation

International Nuclear Information System (INIS)

Sakai, Takao; Yamakawa, Masanori; Otsuka, Masaya; Sekine, Katsuhisa

1986-01-01

Purpose: To reduce equipment thermal stress and deformation by eliminating uneven temperature distribution caused at the equipment through section of the roof slab for the tank FBR, and at the same time, simplify the structure installation. Method: Multiple number of vertical fin projects are fit on the equipment through-section inside wall for the roof slab and the cylindrical equipment peripheral wall, and with these projected fins, the ring space of the through section is vertically divided into multiple sections in the circumferential direction. The vertical fins on the through-section inside wall and the fins on the equipment peripheral wall are contacted with each other by revolving them in the lateral direction. As a result, the natural convection caused by the difference of temperatures in the vertical direction of the ring space becomes a convection within each sector divided, and never generates circumferential circulation, which reduce uneven temperature distribution caused at the equipment through section. (Kawakami, Y.)

Development of an Improved Process for Installation Projects of High Technology Manufacturing Equipment

Energy Technology Data Exchange (ETDEWEB)

Quintana, Sarah V. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-04-30

High technology manufacturing equipment is utilized at Los Alamos National Laboratory (LANL) to support nuclear missions. This is undertaken from concept initiation where equipment is designed and then taken through several review phases, working closely with system engineers (SEs) responsible for each of the affected systems or involved disciplines (from gasses to HVAC to structural, etc.). After the design is finalized it moves to procurement and custom fabrication of the equipment and equipment installation, including all of the paperwork involved. Not only are the engineering and manufacturing aspects important, but also the scheduling, financial forecasting, and planning portions that take place initially and are sometimes modified as the project progresses should requirements, changes or additions become necessary. The process required to complete a project of this type, including equipment installation, is unique and involves numerous steps to complete. These processes can be improved and recent work on the Direct Current Arc (DC Arc) Glovebox Design, Fabrication and Installation Project provides an opportunity to identify some important lessons learned (LL) that can be implemented in the future for continued project improvement and success.

The Emergency Medical System in Greece: Opening Aeolus’ Bag of Winds

Directory of Open Access Journals (Sweden)

Ourania S. Kotsiou

2018-04-01

Full Text Available An Emergency Medical Service (EMS system must encompass a spectrum of care, with dedicated pre-hospital and in-hospital medical facilities. It has to be organised in such a way as to include all necessary services—such as triage accurate initial assessment, prompt resuscitation, efficient management of emergency cases, and transport to definitive care. The global economic downturn has had a direct effect on the health sector and poses additional threats to the healthcare system. Greece is one of the hardest-hit countries. This manuscript aims to present the structure of the Greek EMS system and the impact of the current economic recession on it. Nowadays, primary care suffers major shortages in crucial equipment, unmet health needs, and ineffective central coordination. Patients are also facing economic limitations that lead to difficulties in using healthcare services. The multi-factorial problem of in-hospital EMS overcrowding is also evident and has been linked with potentially poorer clinical outcomes. Furthermore, the ongoing refugee crisis challenges the national EMS. Adoption of a triage scale, expansion of the primary care network, and an effective primary–hospital continuum of care are urgently needed in Greece to provide comprehensive, culturally competent, and high-quality health care.

Management methodology for pressure equipment

Science.gov (United States)

Bletchly, P. J.

Pressure equipment constitutes a significant investment in capital and a major proportion of potential high-risk plant in many operations and this is particularly so in an alumina refinery. In many jurisdictions pressure equipment is also subject to statutory regulation that imposes obligations on Owners of the equipment with respect to workplace safety. Most modern technical standards and industry codes of practice employ a risk-based approach to support better decision making with respect to pressure equipment. For a management system to be effective it must demonstrate that risk is being managed within acceptable limits.

Application and evaluation of training for response to emergency situations

Energy Technology Data Exchange (ETDEWEB)

Kidwell, M.D.

1979-01-01

At Washington Gas Light Co., a magnetic situation-simulation board has become an effective tool for training field personnel in emergency procedures and decisionmaking. Class participants use magnetic disks - symbolizing physical features and components of the distribution system and service equipment - to visually describe the step-by-step procedures applied to specific emergency scenarios. A manually operated clock keeps a running account of the time estimated for each step, emphasizing the need for quick response. Situation-board programs of typical problems, complete with script and drawings, are available to all training foremen to ensure uniform training throughout the department.

21 CFR 58.61 - Equipment design.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

Emergency response facilities including primary and secondary prevention strategies across 79 professional football clubs in England.

Science.gov (United States)

Malhotra, Aneil; Dhutia, Harshil; Gati, Sabiha; Yeo, Tee-Joo; Finocchiaro, Gherardo; Keteepe-Arachi, Tracey; Richards, Thomas; Walker, Mike; Birt, Robin; Stuckey, David; Robinson, Laurence; Tome, Maite; Beasley, Ian; Papadakis, Michael; Sharma, Sanjay

2017-06-14

To assess the emergency response planning and prevention strategies for sudden cardiac arrest (SCA) across a wide range of professional football clubs in England. A written survey was sent to all professional clubs in the English football league, namely the Premiership, Championship, League 1 and League 2. Outcomes included: (1) number of clubs performing cardiac screening and frequency of screening; (2) emergency planning and documentation; (3) automated external defibrillator (AED) training and availability; and (4) provision of emergency services at sporting venues. 79 clubs (86%) responded to the survey. 100% clubs participated in cardiac screening. All clubs had AEDs available on match days and during training sessions. 100% Premiership clubs provided AED training to designated staff. In contrast, 30% of lower division clubs with AEDs available did not provide formal training. Most clubs (n=66; 83%) reported the existence of an emergency action plan for SCA but formal documentation was variable. All clubs in the Premiership and League 1 provided an ambulance equipped for medical emergencies on match days compared with 75% of clubs in the Championship and 66% in League 2. The majority of football clubs in England have satisfactory prevention strategies and emergency response planning in line with European recommendations. Additional improvements such as increasing awareness of European guidelines for emergency planning, AED training and mentorship with financial support to lower division clubs are necessary to further enhance cardiovascular safety of athletes and spectators and close the gap between the highest and lower divisions. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Emergency towing systems for the Aleutian Islands, Alaska

International Nuclear Information System (INIS)

Pearson, L.A.; Brown, J.; Folley, G.; Robertson, T.; Bryant, B.

2009-01-01

Several incidents related to distressed or stricken vessels have occurred in the Aleutian Islands of Alaska, where vessel groundings have caused environmental and economic impacts. A disabled vessel workgroup was formed to discuss local emergency response solutions in the region, particularly for larger tramper or cargo vessels carrying fuel in bottom tanks. The Aleutian emergency towing system (ETS) group developed emergency towing capabilities for disabled vessels in the Aleutian Island sub-area using tugboats in conjunction with ETS equipment stationed in the town of Unalaska. Emergency towing systems were also purchased to serve a wider range of vessels. The ETS consisted of a lightweight towline, a messenger line to assist in deploying the towline, a line-launcher, a lighted buoy, and chafing gear. The components can be configured to deploy a disabled ship from the stern of a tugboat, or air-dropped via helicopter to a ship's deck. A procedures manual and training DVD has been published, and mobilization and deployment exercises are conducted annually. 1 ref., 2 figs

21 CFR 866.4540 - Immunonephelometer equipment.

Science.gov (United States)

2010-04-01

...) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4540 Immunonephelometer equipment. (a) Identification. Immunonephelometer equipment for clinical use...

Survey of injury sources for a trampoline with equipment hazards designed out.

Science.gov (United States)

Eager, David; Scarrott, Carl; Nixon, Jim; Alexander, Keith

2012-07-01

In Australia, trampolines contribute approximately one-quarter of all childhood play-equipment injuries. The purpose of this study was to gather and evaluate injury data from a nontraditional, 'soft-edged', consumer trampoline in which the equipment injury sources have been designed out. A survey was undertaken in Queensland and New South Wales. The manufacturer of the nontraditional trampoline provided the University of Technology, Sydney, with their Australian customer database. Injury data were gathered in a pilot study by phone interview, then in a full study through an email survey. Results from 3817 respondents were compared with earlier Australian and US data from traditional trampolines gathered from emergency departments.   A significantly lower proportion of the injuries caused by falling off or striking the equipment was found for this new design when compared with traditional trampolines both in Australia and in the USA. The age of children being injured on trampolines in Australia was found to be markedly lower than in North America. This research indicates that with appropriate design the more severe injuries on traditional trampolines can be significantly reduced. © 2012 The Authors. Journal of Paediatrics and Child Health © 2012 Paediatrics and Child Health Division (Royal Australasian College of Physicians).

Maintenance program guidelines for programmatic equipment

International Nuclear Information System (INIS)

1994-11-01

The Division Directors at Lawrence Berkeley Laboratory are responsible for implementing a maintenance program for research equipment (also referred to as programmatic equipment) assigned to them. The program must allow maintenance to be accomplished in a manner that promotes operational safety, environmental protection and compliance, and cost effectiveness; that preserves the intended functions of the facilities and equipment; and that supports the programmatic mission of the Laboratory. Programmatic equipment -- such as accelerators, lasers, radiation detection equipment, and glove boxes -- is dedicated specifically to research. Installed equipment, by contrast, includes the mechanical and electrical systems installed as part of basic building construction, equipment essential to the normal functioning of the facility and its intended use. Examples of installed equipment are heating, ventilating, and air conditioning systems; elevators; and communications systems. The LBL Operating and Assurance Program Plan (PUB-3111, Revision 4) requires that a maintenance program be prepared for programmatic equipment and defines the basic maintenance program elements. Such a program of regular, documented maintenance is vital to the safety and quality of research activities. As a part of that support, this document offers guidance to Laboratory organizations for developing their maintenance programs. It clarifies the maintenance requirements of the Operating and Assurance Program (OAP) and presents an approach that, while not the only possibility, can be expected to produce an effective maintenance program for research equipment belonging to the Laboratory's organizations

Development of Turbulence-Measuring Equipment

Science.gov (United States)

Kovasznay, Leslie S G

1954-01-01

Hot wire turbulence-measuring equipment has been developed to meet the more stringent requirements involved in the measurement of fluctuations in flow parameters at supersonic velocities. The higher mean speed necessitates the resolution of higher frequency components than at low speed, and the relatively low turbulence level present at supersonic speed makes necessary an improved noise level for the equipment. The equipment covers the frequency range from 2 to about 70,000 cycles per second. Constant-current operation is employed. Compensation for hot-wire lag is adjusted manually using square-wave testing to indicate proper setting. These and other features make the equipment adaptable to all-purpose turbulence work with improved utility and accuracy over that of older types of equipment. Sample measurements are given to demonstrate the performance.

21 CFR 866.4520 - Immunofluorometer equipment.

Science.gov (United States)

2010-04-01

...) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4520 Immunofluorometer equipment. (a) Identification. Immunofluorometer equipment for clinical use with...

Emergency preparedness

International Nuclear Information System (INIS)

1998-01-01

According the conception of the Emergency Response Centre (ERC) of the Nuclear Regulatory Authority of the Slovak Republic (NRA), and the obtained experience from exercises, and as well as on the basis of recommendations of international missions, the NRA SR started, in 1997 the ERC extension. The new room enable the work for radiation protection group, reactor safety and logistic group separately. At the same time special room was build for work of the NECRA Technical Support Group of the Emergency Commission for Radiation Accidents of the SR.This group co-operates closely with ERC while evaluation the situation, and by using the information system of the NRA and database of ERC to generate the conditions of nuclear facilities in once of emergency. Extension of the mentioned rooms was carried out. The financing by the European Union helped to build the project RAMG. In this way the NRA gained a working site which, with its equipment and parameters belongs to the top working sites of regulatory bodies of developed European countries. The NRA preparation of exercise and special staff education was carried out in 1997, for employees of the NRA and members of Emergency Headquarters (EH) for work in ERC in case of nuclear installation accident. The task of education of member of EH was their preparation for carrying out three exercises. These exercises are described. In the area of emergency preparedness, in accordance with inspection plan of the Office, 7 team inspections were carried out in individual localities; in NPP Bohunice, two in NPP Mochovce and one in Bohunice Conditioning Centre for radioactive wastes. Solution of the task of development of science and technology in the area of 'Development of technical and programme means for analyses of accidents and solutions of crisis situations'continued in 1997. Another regulations were elaborated for activity of members of EH of the NRA. The following was was carried out: selection of data for transfer and the

Data Center Equipment Location and Monitoring System

DEFF Research Database (Denmark)

2013-01-01

Abstract: Data center equipment location systems include hardware and software to provide information on the location, monitoring, and security of servers and other equipment in equipment racks. The systems provide a wired alternative to the wireless RFID tag system by using electronic ID tags...... connected to each piece of equipment, each electronic ID tag connected directly by wires to an equipment rack controller on the equipment rack. The equipment rack controllers link to a central control computer that provides an operator ...

Equipment Reliability Process in Krsko NPP

International Nuclear Information System (INIS)

Gluhak, M.

2016-01-01

To ensure long-term safe and reliable plant operation, equipment operability and availability must also be ensured by setting a group of processes to be established within the nuclear power plant. Equipment reliability process represents the integration and coordination of important equipment reliability activities into one process, which enables equipment performance and condition monitoring, preventive maintenance activities development, implementation and optimization, continuous improvement of the processes and long term planning. The initiative for introducing systematic approach for equipment reliability assuring came from US nuclear industry guided by INPO (Institute of Nuclear Power Operations) and by participation of several US nuclear utilities. As a result of the initiative, first edition of INPO document AP-913, 'Equipment Reliability Process Description' was issued and it became a basic document for implementation of equipment reliability process for the whole nuclear industry. The scope of equipment reliability process in Krsko NPP consists of following programs: equipment criticality classification, preventive maintenance program, corrective action program, system health reports and long-term investment plan. By implementation, supervision and continuous improvement of those programs, guided by more than thirty years of operating experience, Krsko NPP will continue to be on a track of safe and reliable operation until the end of prolonged life time. (author).

[Organizational forms of emergency medicine in international comparison].

Science.gov (United States)

Lipp, M

1993-09-01

The tasks of preclinical emergency medicine systems (PEMS) are to stabilize and maintain the vital functions and to guarantee qualified transport to the hospital. Worldwide, different structures exist as a result of historical developments. Legal regulations for PEMS have been introduced in most of the industrialized countries since 1960. More and more aspects have been subject to detailed regulations. PEMS are provided either by state-owned or by state-controlled (private) organisations. In most of the "underdeveloped" countries legal regulations do not exist and PEMS is often provided by social workers, by the army or by volunteers. In most countries, PEMS are financed by the state with a charge on the patient. In a few states PEMS are totally financed by the public health structure. Modern PEMS are controlled from dispatch centres which receive emergency calls (mostly by telephone) and send the appropriate rescue unit. In most states the staff of dispatch centres are paramedics; in some countries and in some urban areas physicians control the dispatch centre. In PEMS without physicians on the scene, an information exchange between the scene and the hospital can be observed frequently, in contrast to systems with physicians on the scene. Worldwide, ground-based PEMS are preferred, but in most countries an additional air rescue system has been established. The quality and quantity of the technical equipment of the ground-based PEMS differ widely: nationwide regulations exist, however, in the USA and Germany. Generally, there are two main concepts concerning the personnel structure: PEMS are either physician based or not. Requirements for emergency physicians differ greatly: in some countries no formal requirements exist, in others extensive practical and theoretical training is required.(ABSTRACT TRUNCATED AT 250 WORDS)

IAEA response assistance network. Incident and Emergency Centre. Emergency preparedness and response. Date effective: 1 May 2006

International Nuclear Information System (INIS)

2006-03-01

This publication is intended to serve as a tool for supporting the provision of international assistance in the case of nuclear or radiological incident or emergency, cooperation between States, their Competent Authorities and the IAEA, and harmonization of response capabilities of States offering assistance. The publication is issued under the authority of the Director General of the IAEA: (1) under the auspices of the Convention on Assistance in the Case of a Nuclear Accident or Radiological Emergency (the Assistance Convention) [1], to promote, facilitate and support cooperation between States Parties to coordinate and/or provide assistance to a State Party and/or Member State; and (2) in the case of an incident or emergency, as statutory functions, to provide for the application of its safety standards, upon request by a Member State, and to act as an intermediary for the purposes of securing the performance of services or the supplying of materials, equipment or facilities by one Member State for another. The publication sets out the following: a) the RANET concept and the organizational structure for providing assistance; b) functions, responsibilities and activities within the RANET; c) the RANET response operations and arrangements needed for preparedness; and d) the prerequisites for RANET membership and conditions of registration. The RANET is divided into four sections. After the introduction in Section 1, the RANET concept, objectives and scope are described in Section 2. Section 3 presents the concept of operations of the RANET and Section 4 describes expected tasks, capabilities and resources. In addition, EPR-RANET (2006) has three supporting documents, which are issued separately, as follows: 1. Assistance Action Plans with samples of Assistance Action Plans for providing international assistance. 2. Registry with the details of the registry and instructions on how to register national assistance capabilities for the RANET. 3. Technical Guidelines

Resuscitation and emergency management for neonatal foals.

Science.gov (United States)

Corley, Kevin T T; Axon, Jane E

2005-08-01

Early intervention can dramatically alter outcome in foals. Cardio-pulmonary cerebral resuscitation can be successful and clinically worthwhile when applied to foals that arrest as part of the birthing process. Readily available equipment and an ordered plan starting with addressing the respiratory system (airway and breathing) followed by the circulatory system (circulation and drugs) are the keys to success. Hypoglycemia is common in foals that are not nursing and in septic foals. Support of serum glucose can be an important emergency treatment. Respiratory support with oxygen therapy should be considered in all foals following resuscitation and dystocia. Other foals that are likely to benefit from oxygen are those that are dyspneic, cyanotic, meconium-stained after birth,or recumbent. Emergency therapies, applied correctly, are expected to result in decreased mortality and morbidity.

Data center equipment location and monitoring system

DEFF Research Database (Denmark)

2011-01-01

A data center equipment location system includes both hardware and software to provide for location, monitoring, security and identification of servers and other equipment in equipment racks. The system provides a wired alternative to the wireless RFID tag system by using electronic ID tags...... connected to each piece of equipment, each electronic ID tag connected directly by wires to a equipment rack controller on the equipment rack. The equipment rack controllers then link over a local area network to a central control computer. The central control computer provides an operator interface......, and runs a software application program that communicates with the equipment rack controllers. The software application program of the central control computer stores IDs of the equipment rack controllers and each of its connected electronic ID tags in a database.; The software application program...

Advisibility of excavating an additional central shaft to reduce duration of mine construction. [USSR

Energy Technology Data Exchange (ETDEWEB)

Durov, E.M.

1981-09-01

This paper evaluates methods of reducing duration and cost of underground black coal mine construction. A proposed scheme of coal deposit opening by a system of three mine shafts is critically analyzed. In comparison to the conventional scheme, the proposed one has one additional mine shaft in the central mine zone. The shaft, equipped with a cage hoisting system, permits the rate of mine drivage in the center of the mine to be increased. The cage hoisting system in the additional shaft is activated before the main skip shaft has been equipped and is in operation. Duration of mine construction is reduced by 6 to 10 months. Exacavation of the additional shaft costs from 2.5 to 3.5 million rubles. A further system of mine construction is also analyzed. The main shaft in the mine center is temporarily equipped with a cage hoisting system. The cage system is used for hoisting rocks removed from mine headings and main workings constructed at the bottom of the main shaft. The main shaft is equipped with skips and hoisting tower at a later stage when construction of main roadways and structures at its bottom has been completed. The proposed system permits mine construction to be reduced by 4 to 5 months without a major increase in investment.

Radiation protection instrumentation. Monitoring equipment. Atmospheric radioactive iodine in the environment

International Nuclear Information System (INIS)

1995-01-01

This international standard applies to portable or installed equipment for the monitoring of radioactive iodine (such as I-131 or I-125) in air in the environment of nuclear installations during normal operation, during design basis events, and in emergency situations. The monitoring involves continuous sample trapping and, where adequate, automatic start of sampling. The document deals with radioactive iodine monitor design, testing procedures, and documentation. Appended tables refer to the reference and normal testing conditions, tests in normal testing conditions, tests during changes of the affecting quantities, and tests of changes in the air circuit. (P.A.)

Signal-Noise Ratio Control Subsystem of Digital Equipment for Transmission of "Strela" Relay Protection Commands

Directory of Open Access Journals (Sweden)

I. I. Zabenkov

2012-01-01

Full Text Available Continuous measurement function of relative noise and interference level in the information transmission channel is considered as an important one for controlling parameters of high-frequency signal. The present paper simulates an algorithm for measuring signal-noise ratio in the transmission channel of high-voltage lines which is used in the digital equipment for transmission of relay protection and emergency automation commands of "Strela" complex.

7 CFR 3015.167 - Replacement of equipment.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Replacement of equipment. 3015.167 Section 3015.167..., DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Property § 3015.167 Replacement of equipment. (a) If needed, equipment may be exchanged for replacement equipment. Replacement of equipment may be...

Urine Exosomes: An Emerging Trove of Biomarkers.

Science.gov (United States)

Street, J M; Koritzinsky, E H; Glispie, D M; Star, R A; Yuen, P S T

Exosomes are released by most cells and can be isolated from all biofluids including urine. Exosomes are small vesicles formed as part of the endosomal pathway that contain cellular material surrounded by a lipid bilayer that can be traced to the plasma membrane. Exosomes are potentially a more targeted source of material for biomarker discovery than unfractionated urine, and provide diagnostic and pathophysiological information without an invasive tissue biopsy. Cytoplasmic contents including protein, mRNA, miRNA, and lipids have all been studied within the exosomal fraction. Many prospective urinary exosomal biomarkers have been successfully identified for a variety of kidney or genitourinary tract conditions; detection of systemic conditions may also be possible. Isolation and analysis of exosomes can be achieved by several approaches, although many require specialized equipment or involve lengthy protocols. The need for timely analysis in the clinical setting has driven considerable innovation with several promising options recently emerging. Consensus on exosome isolation, characterization, and normalization procedures would resolve critical clinical translational bottlenecks for existing candidate exosomal biomarkers and provide a template for additional discovery studies. 2017 Published by Elsevier Inc.

Additional examination on station blackout caused by tsunami in Fukushima Daiichi NPS

International Nuclear Information System (INIS)

Yamauchi, Daisuke; Date, Kenji; Mizokami, Masato; Honda, Takeshi; Nozaki, Kenichiro; Mizokami, Shinya; Endo, Ryohei

2017-01-01

This study is additional examination to verify in a more reliable way the assessment that the emergency AC power supply was lost due to tsunami at Fukushima Daiichi Nuclear Power Station. It confirmed the relationship between the path length of tsunami intrusion reaching each power supply facility and the function loss time. As a result of examination, it was confirmed that as the path length of the tsunami intrusion reaching each power supply facility was longer, the function loss time tended to be later. So, conventional assessment that the function of each power supply facility was lost due to the run-up and flooding of tsunami has become more probable. For facilities, where the overall trend and the loss time of function were divergent, it was found that there were scenarios that could reasonably be explained. Based on the fact that the Fukushima Daiichi Nuclear Power Station lost power due to the tsunami, Kashiwazaki-Kariwa Nuclear Power Station carries out various safety measures. First of all, as the measures to prevent accidents caused by tsunami, the following have been applied: (1) prevention of the inflow of tsunamis into premises, (2) water prevention of the areas installed with important equipment, (3) securement of seawater at the time of backwashing, (4) storage of portable equipment at high ground, (5) installation of tsunami surveillance cameras. To prepare for the loss of power supply, this station implemented power supply facilities such as generator cars and distribution boards, as well as the placement of power supply cars at high ground. (A.O.)

Use of commercial grade equipment and industrial standards for equipment qualification

International Nuclear Information System (INIS)

Gradin, L.P.; Muller, E.S.

1984-01-01

One of the most controversial issues is the proper application of Arrhenius aging methodology. Naturally and artificially aged equipment used in type test programs are often costly and burdensome tasks. Appropriate use of non-nuclear industrial standards and comparison to past history can demonstrate, with reasonable assurance, that equipment is qualified with proper consideration of aging. Specific review of the industrial standards available and application examples are provided

The presence of biofilm forming microorganisms on hydrotherapy equipment and facilities.