Ethanol production from biodiesel-derived crude glycerol by newly isolated Kluyvera cryocrescens

Energy Technology Data Exchange (ETDEWEB)

Choi, Won Jae; Hartono, Maria Regina; Chan, Weng Heng; Yeo, Suan Siong [Agency for Science, Technology and Research (A*STAR), Jurong Island (Singapore). Inst. of Chemical and Engineering Sciences

2011-02-15

The rapidly expanding market for biodiesel has increased the supply and reduced the cost of glycerol, making it an attractive sustainable feed stock for the fuel and chemical industry. Glycerol-based biorefinery is the microbial fermentation of crude glycerol to produce fuels and chemicals. A major challenge is to obtain microbes tolerant to inhibitors such as salts and organic solvents present in crude glycerol. Microbial screening was attempted to isolate novel strain capable of growing on crude glycerol as a sole carbon source. The newly isolated bacteria, identified as nonpathogenic Kluyvera cryocrescens S26 could convert biodiesel-derived crude glycerol to ethanol with high yield and productivity. The supplementation of nutrients such as yeast extract resulted in distinguished enhancement in cell growth as well as ethanol productivity under anaerobic condition. When glycerol fermentation is performed under microaerobic condition, there is also a remarkable improvement in cell growth, ethanol productivity and yield, compared with those under strict anaerobic condition. In batch fermentation under microaerobic condition, K. cryocrescens S26 produced 27 g/l of ethanol from crude glycerol with high molar yield of 80% and productivity of 0.61 g/l/h. (orig.)

Characterization of crude oils and petroleum products: (I Elution liquid chromatographic separation and gas chromatographic analysis of crude oils and petroleum products

Directory of Open Access Journals (Sweden)

E.O. Odebunmi

2002-12-01

Full Text Available Some physical and chemical properties of samples of light, medium and heavy Nigerian crude oils and petroleum products including gasoline, kerosene and engine oil have been measured and are reported in this paper. The crude oils and petroleum products have also been characterized by fractional distillation and elution liquid chromatography. The fractions obtained from elution liquid chromatography were analyzed using gas chromatography (GC. The GC fractions were identified by comparing the retention time of peaks in the unknown samples with those of components of calibration standard mixtures. The importance of the physico-chemical properties and the significance of the fractional distillation and chromatographic separation methods to industrial process operations have been discussed.

Time Course-Dependent Methanogenic Crude Oil Biodegradation: Dynamics of Fumarate Addition Metabolites, Biodegradative Genes, and Microbial Community Composition

Directory of Open Access Journals (Sweden)

Courtney R. A. Toth

2018-01-01

Full Text Available Biodegradation of crude oil in subsurface petroleum reservoirs has adversely impacted most of the world's oil, converting this resource to heavier forms that are of lower quality and more challenging to recover. Oil degradation in deep reservoir environments has been attributed to methanogenesis over geological time, yet our understanding of the processes and organisms mediating oil transformation in the absence of electron acceptors remains incomplete. Here, we sought to identify hydrocarbon activation mechanisms and reservoir-associated microorganisms that may have helped shape the formation of biodegraded oil by incubating oilfield produced water in the presence of light (°API = 32 or heavy crude oil (°API = 16. Over the course of 17 months, we conducted routine analytical (GC, GC-MS and molecular (PCR/qPCR of assA and bssA genes, 16S rRNA gene sequencing surveys to assess microbial community composition and activity changes over time. Over the incubation period, we detected the formation of transient hydrocarbon metabolites indicative of alkane and alkylbenzene addition to fumarate, corresponding with increases in methane production and fumarate addition gene abundance. Chemical and gene-based evidence of hydrocarbon biodegradation under methanogenic conditions was supported by the enrichment of hydrocarbon fermenters known to catalyze fumarate addition reactions (e.g., Desulfotomaculum, Smithella, along with syntrophic bacteria (Syntrophus, methanogenic archaea, and several candidate phyla (e.g., “Atribacteria”, “Cloacimonetes”. Our results reveal that fumarate addition is a possible mechanism for catalyzing the methanogenic biodegradation of susceptible saturates and aromatic hydrocarbons in crude oil, and we propose the roles of community members and candidate phyla in our cultures that may be involved in hydrocarbon transformation to methane in crude oil systems.

Economic and environmental effects of the FQD on crude oil production from tar sands

Energy Technology Data Exchange (ETDEWEB)

Kampman, B.; De Buck, A.; Afman, M. [CE Delft, Delft (Netherlands); Van den Berg, J.; Otten, G.J. [Carbon Matters, Den Haag (Netherlands)

2013-05-15

The production of unconventional crudes in Canada and Venezuela and exports of these crudes to the EU are investigated. In addition the potential economic and environmental impact of the proposed EU FQD measures (Fuel Quality Directive) on the production of crudes from tar sands and on new tar sand exploration projects are examined. CE Delft has analysed the impact by using a dedicated cost model. For existing projects, the model determines the effect on the basis of marginal production costs. For planned projects the model used the net present value (NPV) of proposed investments. The impacts were determined for a range of crude oil prices and FQD price effects. Combined, for existing and new projects together, the maximum effect would be at a price level at 60 USD/bbl, with savings of up to 19 Mt CO2/y at an FQD price differential of 3 euro/bbl. This overall effect would be substantial and come on top of the total emission reduction effect of the FQD of 60 Mt CO2/y, which will be achieved mostly by the blending of low-carbon fuels and reduced flaring and venting. As part of the reduction of transport greenhouse gas (GHG) emissions, the revised FQD obliges fuel suppliers to reduce these emissions by 6% by 2020 on a well-to-wheel basis. The EU is currently developing a methodology to differentiate fossil fuels on the basis of feedstock and GHG emissions. In the proposal, diesel produced from tar sands, has been given a default emission value of 108.5 gCO2 eq/MJ, while diesel from conventional crude was set at 89.1 gCO2 eq/MJ. The Commission's proposal is currently undergoing an impact assessment and is expected to be resubmitted to the Council later this year (2013)

Characteristics of bicyclic sesquiterpanes in crude oils and petroleum products.

Science.gov (United States)

Yang, Chun; Wang, Zhendi; Hollebone, Bruce P; Brown, Carl E; Landriault, Mike

2009-05-15

This study presents a quantitative gas chromatography-mass spectrometry analysis of bicyclic sesquiterpanes (BSs) in numerous crude oils and refined petroleum products including light and mid-range distillate fuels, residual fuels, and lubricating oils collected from various sources. Ten commonly recognized bicyclic sesquiterpanes were determined in all the studied crude oils and diesel range fuels with principal dominance of BS3 (C(15)H(28)), BS5 (C(15)H(28)) and BS10 (C(16)H(30)), while they were generally not detected or in trace in light fuel oils like gasoline and kerosene and most lubricating oils. Laboratory distillation of crude oils demonstrated that sesquiterpanes were highly enriched in the medium distillation fractions of approximately 180 to 481 degrees C and were generally absent or very low in the light distillation fraction (boiling point to approximately 180 degrees C) and the heavy residual fraction (>481 degrees C). The effect of evaporative weathering on a series of diagnostic ratios of sesquiterpanes, n-alkanes, and biomarkers was evaluated with two suites of weathered oil samples. The change of abundance of sesquiterpanes was used to determine the extent of weathering of artificially evaporated crude oils and diesel. In addition to the pentacyclic biomarker C(29) and C(30) alphabeta-hopane, C(15) and C(16) sesquiterpanes might be alternative internal marker compounds to provide a direct way to estimate the depletion of oils, particularly diesels, in oil spill investigations. These findings may offer potential applications for both oil identification and oil-source correlation in cases where the tri- to pentacyclic biomarkers are absent due to refining or environmental weathering of oils.

Bioconversion from crude glycerin by Xanthomonas campestris 2103: xanthan production and characterization

Directory of Open Access Journals (Sweden)

L. V. Brandão

2013-12-01

Full Text Available The production and rheological properties of xanthan gum from crude glycerin fermentation, a primary by-product of the biodiesel industry with environmental and health risks, were evaluated. Batch fermentations (28 °C/250 rpm /120 h were carried out using crude glycerin, 0.01% urea and 0.1% KH2PO4, (% w/v, and compared to a sucrose control under the same operational conditions, using Xanthomonas campestris strain 2103 isolate from Brazil. Its maximal production by crude glycerin fermentation was 7.23±0.1 g·L-1 at 120 h, with an apparent viscosity of 642.57 mPa·s, (2 % w/v, 25 °C, 25 s-1, 70% and 30% higher than from sucrose fermentation, respectively. Its molecular weight varied from 28.2 to 36.2×10(6 Da. The Ostwald-de-Waele model parameters (K and n indicated a pseudoplastic behavior at all concentrations (0.5 to 2.0 %, w/v and temperatures (25-85 °C, while its consistency index indicated promising rheological properties for drilling fluid applications. Therefore, crude glycerin has potential as a cost-effective and alternative substrate for non-food grade xanthan production.

Conversion of Crude Oil to Methane by a Microbial Consortium Enriched From Oil Reservoir Production Waters

Directory of Open Access Journals (Sweden)

Carolina eBerdugo-Clavijo

2014-05-01

Full Text Available The methanogenic biodegradation of crude oil is an important process occurring in petroleum reservoirs and other oil-containing environments such as contaminated aquifers. In this process, syntrophic bacteria degrade hydrocarbon substrates to products such as acetate, and/or H2 and CO2 that are then used by methanogens to produce methane in a thermodynamically dependent manner. We enriched a methanogenic crude oil-degrading consortium from production waters sampled from a low temperature heavy oil reservoir. Alkylsuccinates indicative of fumarate addition to C5 and C6 n-alkanes were identified in the culture (above levels found in controls, corresponding to the detection of an alkyl succinate synthase gene (assA in the culture. In addition, the enrichment culture was tested for its ability to produce methane from residual oil in a sandstone-packed column system simulating a mature field. Methane production rates of up 5.8 μmol CH4/g of oil/day were measured in the column system. Amounts of produced methane were in relatively good agreement with hydrocarbon loss showing depletion of more than 50% of saturate and aromatic hydrocarbons. Microbial community analysis revealed that the enrichment culture was dominated by members of the genus Smithella, Methanosaeta, and Methanoculleus. However, a shift in microbial community occurred following incubation of the enrichment in the sandstone columns. Here, Methanobacterium sp. were most abundant, as were bacterial members of the genus Pseudomonas and other known biofilm forming organisms. Our findings show that microorganisms enriched from petroleum reservoir waters can bioconvert crude oil components to methane both planktonically and in sandstone-packed columns as test systems. Further, the results suggest that different organisms may contribute to oil biodegradation within different phases (e.g., planktonic versus sessile within a subsurface crude oil reservoir.

Using crude glycerol and thin stillage for the production of microbial lipids through the cultivation of Rhodotorula glutinis.

Science.gov (United States)

Yen, Hong-Wei; Yang, Ya-Chun; Yu, Yi-Huan

2012-10-01

Single cell oils (SCO) produced from oleaginous microorganisms are a potential alternative oil feedstock for biodiesel production. The worldwide production of glycerol, a 10% (w/w) byproduct produced in the transesterfication process of oils converted to biodiesel, is increasing as more biodiesel is being produced. For the purposes of cost reduction, crude glycerol was regarded as a suitable carbon source for the cultivation of Rhodotorula glutinis. In addition to using renewable crude glycerol, waste solution collected from the brewing company (called thin stillage) was adopted as a substitute to replace a costly nitrogen source used in the medium. The results of using mixture of crude glycerol and thin stillage indicated about a 27% increase in total biomass as compared to that of using crude glycerol with a standard medium. Using glycerol instead of glucose as the carbon source could also alter the lipid profile, resulting in an increase in linolenic acid (C18:2) to comprise over 20% of the total lipid. Successfully using renewable crude glycerol and thin stillage for the cultivation of oleaginous microorganisms could greatly enhance the economic competition of biodiesel produced from SCO. Copyright © 2012 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Influences of Fuel Additive, Crude Palm and Waste Cooking Oil on Emission Characteristics of Small Diesel Engine

Science.gov (United States)

Khalid, Amir; Jaat, Norrizam; Manshoor, Bukhari; Zaman, Izzuddin; Sapit, Azwan; Razali, Azahari; Basharie, Mariam

2017-08-01

Major research has been conducted on the use of input products, such as rapeseed, canola, soybean, sunflower oil, waste cooking oil (WCO), crude palm oil (CPO) and crude jatropha oil as alternative fuels. Biodiesel is renewable, biodegradable and oxygenated, where it can be easily adopted by current existing conventional diesel engine without any major modification of the engine. To meet the future performance and emission regulations, is urged to improve the performance and exhaust emissions from biodiesel fuels. Hence, further investigation have been carried out on the emission characteristics of small diesel engine that fuelled by variant blending ratio of WCO and CPO with booster additive. For each of the biodiesel blends ratio from 5 to 15 percent volume which are WCO5, WCO10 and WCO15 for WCO biodiesel and CPO5, CPO10 and CPO15 for CPO biodiesel. The exhaust emissions were measured at engine speeds varied at 2000 rpm and 2500 rpm with different booster additive volume DRA (biodiesel without additive), DRB (0.2 ml) and DRC (0.4 ml). Emissions characteristics that had been measured were Hydrocarbon (HC), Carbon Monoxide (CO), Carbon Dioxide (CO2), Nitrogen Oxide (NOx), and smoke opacity. The results showed that increased of blending ratio with booster additive volume significantly decreased the CO emission, while increased in NOx and CO2 due to changes of fuel characteristics in biodiesel fuel blends.

Canada's crude oil resources : crude oil in our daily lives

International Nuclear Information System (INIS)

Bott, R.

2001-10-01

Created in 1975, the Petroleum Communication Foundation is a not-for-profit organization. The objective of the Foundation is to inform Canadians about the petroleum industry in Canada. It produces educational, fact-based publications and programs, employing a multi-stakeholder review process. The first section of this publication is devoted to crude oil and the benefits that are derived from it. It begins by providing a brief definition of crude oil, then moves to the many uses in our daily lives and the environmental impacts like air pollution, spills, and footprint on the land from exploration and production activities. Section 2 details the many uses of crude oil and identifies the major oil producing regions of Canada. A quick mention is made of non-conventional sources of crude oil. The search for crude oil is the topic of section 3 of the document, providing an overview of the exploration activities, the access rights that must be obtained before gaining access to the resource. The drilling of oil is discussed in section 4. Section 5 deals with issues pertaining to reservoirs within rocks, while section 6 covers the feeding of the refineries, discussing topics from the movement of oil to market to the refining of the crude oil, and the pricing issues. In section 7, the uncertain future is examined with a view of balancing the supply and demand, as crude oil is a non-renewable resource. Supplementary information is provided concerning additional publications published by various organizations and agencies. figs

Catalytic hydrothermal liquefaction (HTL of biomass for bio-crude production using Ni/HZSM-5 catalysts

Directory of Open Access Journals (Sweden)

Shouyun Cheng

2017-04-01

Full Text Available Hydrothermal liquefaction (HTL is an effective method that can convert biomass into bio-crude, but direct use of bio-crude derived from biomass HTL remains a challenge due to the lower quality. In this study, bifunctional Ni/HZSM-5 catalysts and zinc hydrolysis were combined to produce upgraded bio-crude in an in-situ HTL process. The K2CO3 and HZSM-5 catalysts with different Ni loading ratios were tested. The effects of different catalysts on the yield and quality of bio-crude and gas were investigated. The results indicated that the catalysts improved bio-crude and gas yields, compared to pine sawdust liquefaction without catalyst. The catalysts reduced the contents of undesirable oxygenated compounds such as acids, ketones, phenols, alcohols and esters in bio-crude products while increased desirable hydrocarbons content. K2CO3 produced highest bio-crude yield and lowest solid residue yield among all catalysts. Compared to parent HZSM-5 catalyst, bifunctional Ni/HZSM-5 catalysts exhibited higher catalyst activity to improve quality of upgraded bio-crude due to its integration of cracking and hydrodeoxygenation reactions. 6%Ni/HZSM-5 catalyst produced the bio-crude with the highest hydrocarbons content at 11.02%. This catalyst can be a candidate for bio-crude production from biomass HTL.

Price Relationships in the Petroleum Market: An Analysis of Crude Oil and Refined Product Prices

International Nuclear Information System (INIS)

Asche, Frank; Gjoelberg, Ole; Voelker, Teresa

2001-08-01

In this paper the relationships between crude oil and refined product prices are investigated in a multivariate framework. This allows us to test several (partly competing) assumptions of earlier studies. In particular, we find that the crude oil price is weakly exogenous and that the spread is constant in some but not all relationships. Moreover, the multivariate analysis shows that the link between crude oil prices and several refined product prices implies market integration for these refined products. This is an example of supply driven market integration and producers will change the output mix in response to price changes. (author)

Price relationships in the petroleum market. An analysis of crude oil and refined product prices

International Nuclear Information System (INIS)

Asche, Frank; Gjoelberg, Ole; Volker, Teresa

2003-01-01

In this paper the relationships between crude oil and refined product prices are investigated in a multivariate framework. This allows us to test several (partly competing) assumptions of earlier studies. In particular, we find that the crude oil price is weakly exogenous and that the spread is constant in some but not all relationships. Moreover, the multivariate analysis shows that the link between crude oil prices and several refined product prices implies market integration for these refined products. This is an example of supply driven market integration and producers will change the output mix in response to price changes

Price relationships in the petroleum market: an analysis of crude oil and refined product prices

International Nuclear Information System (INIS)

Asche, F.; Gjoelberg, O.; Voelker, T.

2003-01-01

In this paper the relationships between crude oil and refined product prices are investigated in a multivariate framework. This allows us to test several (partly competing) assumptions of earlier studies. In particular, we find that the crude oil price is weakly exogenous and that the spread is constant in some but not all relationships. Moreover, the multivariate analysis shows that the link between crude oil prices and several refined product prices implies market integration for these refined products. This is an example of supply driven market integration and producers will change the output mix in response to price changes. (author)

Assessing refinery capacity and readiness to take Canadian product : is Canadian crude pushing or pulling?

International Nuclear Information System (INIS)

Friesner, J.M.

2005-01-01

This presentation addressed some of the challenges facing oil sands production in Canada. Refinery products and refining investments were discussed, as was the impact of alternative crude supply on the markets and pricing of oil sands. The oils sands products discussed include various qualities of sweet synthetic crude oil produced via upgraders; virgin and cracked intermediate products from oil sands upgraders; mined or Steam Assisted Gravity Drainage (SAGD) produced bitumen blended products; and synthetic heavy crude produced via hydrocracking. Products were listed in terms of ease of production, and a rationale for generic ranking was provided. A chart of 2003 characteristics of non-Canadian imports to the mid-west United States was provided. Various marketing strategies for different oil sands products were discussed, as well as issues concerning logistics. Strategies for the development of a bigger market include producer investment in refining capability; the acquisition of refining assets; investment in refiners' upgrading capability; and securing a long term supply deal. Core and extended markets for Western Canadian oil sands products were reviewed. A chart of North American refining capacity was presented. Details of a refinery with both coking and cracking capacity were examined. An increase in hydro processing capacity and expanded coking capacity, as well as an upgrade of metallurgy were suggested as possible upgrading options. Various refinery configurations were discussed in relation to lower cost feedstocks and clean fuels specifications. Issues concerning crude supply were examined with reference to pricing parity points and declines in traditional crude production. Specific supply issues concerning oil sands production were discussed, including transportation costs; adequate refining capacity; and availability of supply. Various logistic investments were considered. A map of BP's 5 U.S. refineries was presented. A forecast of expected changes in

Implications of globalization on pricing for Canadian crudes

Energy Technology Data Exchange (ETDEWEB)

Black, R. [Canadian Occidental Petroleum Ltd., Calgary, AB (Canada)

1998-05-01

The effects of globalization on Canadian crude oil prices was discussed. Since deregulation in October 1985, Canadian crude oil has competed directly against international crude oil through the use of the NYMEX contract price for light sweet crude oil as the base for establishing the price for Canadian crudes. Prior to that date, Alberta crude was marketed by the Alberta Petroleum Marketing Commission using the old block matrix which was loosely tied to the world market price. In addition to world crude oil prices other factors that affect the price of Canadian crude oil include technology impacts and global integration. Also, when the Sarnia to Montreal pipeline (Line 9) is reversed to bring offshore crude oil into the Ontario refining community, Canadian producers can expect some adverse effects on the price they are paid for their products leading up to the reversal as refiners start to swing over to their alternate suppliers. The offshore supply is expected to be about 140,000 barrels/day of light sweet crude oil, but all grades of Canadian crude oil will be affected.

GC/MS determination of bicyclic sesquiterpanes in crude oils and petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.; Hollebone, B.; Brown, C.E.; Landriault, M.

2008-01-01

A study was conducted in which sesquiterpanes, a component of crude oils and petroleum products, were identified and characterized in an effort to determine the feasibility of using them as biomarkers for fingerprinting and identifying unknown lighter petroleum product spills. The study compared the distributions of sesquiterpanes in different oils, oil distillation fractions and refined products, including light and mid-range distillate fuels, residual fuels and lubricating oils. Evaporative weathering effects on sesquiterpane distribution and concentration were quantitatively studied and several diagnostic indices of sesquiterpane were developed for oil correlation and differentiation. Bicyclic sesquiterpanes in crude oils and oil products have much different abundances and distributions. Therefore, the relevant sesquiterpane ratios are different. Bicyclic sesquiterpanes are mostly partitioned into the medium distillation fractions. The study showed that concentrations of sesquiterpanes in crude oil and diesel fuel increase in proportion with the increase of weathering percentages. Relevant diagnostic ratios therefore remained stable. It was concluded that C 15 and C 16 sesquiterpanes may be alternative internal tracers to provide a direct way to estimate the depletion of oils, particularly diesels, in oil spill investigations. 13 refs., 6 tabs., 4 figs

1999 Crude oil market outlook

International Nuclear Information System (INIS)

Cochener, J.

1998-01-01

Baseline projection handling of crude oil prices was discussed, based on actual crude oil price trends from 1992 to 1998. Attention was drawn to the lack of correlation between crude oil and natural gas prices. Predictions for crude oil production were extended to the year 2015. As far as the immediate future is concerned the crude oil price for 1999 was predicted to continue to be sluggish due to competitive pressure from refined products at burner tip. tabs., figs

Malic acid production by chemically induced Aspergillus niger MTCC 281 mutant from crude glycerol.

Science.gov (United States)

Iyyappan, J; Bharathiraja, B; Baskar, G; Jayamuthunagai, J; Barathkumar, S; Anna Shiny, R

2018-03-01

In the present investigation, crude glycerol derived from transesterification process was utilized to produce the commercially-valuable malic acid. A combined resistant on methanol and malic acid strain of Aspergillus niger MTCC 281 mutant was generated in solid medium containing methanol (1-5%) and malic acid (40-80 g/L) by the adaptation process for 22 weeks. The ability of induced Aspergillus niger MTCC 281 mutant to utilize crude glycerol and pure glycerol to produce malic acid was studied. The yield of malic acid was increased with 4.45 folds compared with that of parent strain from crude glycerol. The highest concentration of malic acid from crude glycerol by using beneficial mutant was found to be 77.38 ± 0.51 g/L after 192 h at 25 °C. This present study specified that crude glycerol by-product from biodiesel production could be used for producing high amount of malic acid without any pretreatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Factors affecting future crude oil production in South East Asia

International Nuclear Information System (INIS)

Baugh, M.A.

1996-01-01

In the face of booming regional demand, crude oil production in the South East Asian region will decline from a 1996 peak of 5.7 million barrels a day to 3.5 million barrels a day in 2005 unless major new exploration investments are undertaken. The current fiscal terms for such investment will not attract continued significant funds to the region given the low crude price outlook, tough competitive global environment for the upstream industry, and the emergence of more attractive fiscal terms in politically and commercially stable countries with proven prospectivity. There is evidence from the emerging trend toward fiscal terms softening and differentiation around risk in some countries, that the commercial reality is becoming accepted. It remains to be seen if the various national political, bureaucratic and industry constituencies guiding these decisions within the region can respond decisively to mitigate the growing crude import dependency. (author). 2 tabs

Co-digestion of crude glycerin associated with cattle manure in biogas production in the State of Paraná, Brazil

Directory of Open Access Journals (Sweden)

Felix Augusto Pazuch

2017-05-01

Full Text Available The addition of different concentrations of crude glycerin, associated with cattle manure, on the volumetric production of biogas is analyzed. Different concentrations of crude glycerin (2, 4 and 6% m m-1 were added as supplement in anaerobic co-digestion of dairy cattle waste, in laboratory batch biodigesters (3.5 L usable volume. The biodigesters were operated under mesophilic conditions (30ºC, with 30-day hydraulic retention time (HRT. Total solids (TS, volatile solids (VS and chemical oxygen demand (COD were analyzed to determine the efficiency of the process in the removal of organic matter and its effect on biogas production. The addition of 4% glycerin provided a larger production of biogas, approximately 9.307 mL. The efficiency in COD removal decreased in treatments with glycerin, with highest reduction (68% in the control treatment. There was a 90 and 118% increase respectively for Gli4 and Gli6% treatments. VS reductions Gly 0, Gly 2, Gly 4 and Gly 6% treatments were 18.17, 61.60, 24.36 and 44.83%, for the respective treatments.

Crude petroleum

International Nuclear Information System (INIS)

1990-01-01

Crude petroleum statistics by country of production, export values and import values from 1983 to 1988 are given. Table A.1 of the Annex includes free market prices and price indices for crude petroleum based on average of Dubai, United Kingdom Brent and Alaska N Slope crude prices (price expressed in dollars/barrel). The data sources are: Crude petroleum United Nations Statistical Office; OPEC Annual Statistical Bulletin, and Petroleum Economist. For trade the sources of data are: National trade statistics; United Nations international trade statistics; International Moneytary Fund (IMF); Organization of the Petroleum Exporting Countries (OPEC); UNCTAD secretariat estimates. Tabs

1,3-Propanediol production from crude glycerol by Clostridium butyricum DSP1 in repeated batch

Directory of Open Access Journals (Sweden)

Daria Szymanowska-Powałowska

2014-11-01

Conclusions: The experiments proved that by using a portion of metabolically active biomass as inoculum for another fermentation formula it is possible to eliminate the stage of inoculum growth and thereby reduce the length of the whole operation. Additionally, that strategy avoids the phase of microbial adaptation to a different source of carbon such as crude glycerol, which is more difficult to utilize, thus improving the kinetic parameters of 1,3-PD production.

Biodiesel production from tall oil with synthesized Mn and Ni based additives: effects of the additives on fuel consumption and emissions

Energy Technology Data Exchange (ETDEWEB)

Ali Keskin; Metin Guru; Duran Altiparmak [Mersin University, Mersin (Turkey). Technical Education Faculty

2007-05-15

In this study, biodiesel fuel and fuel additives were produced from crude tall oil that is a by-product in the pulp manufacturing by craft or sulphate pulping process. Fatty acids and resinic acids were obtained from crude tall oil by distillation method. Tall oil methyl ester (biodiesel) was produced from fatty acids. Resinic acids were reacted with NiO and MnO{sub 2} stoichiometrically for production of metallic fuel additives. Each metallic fuel additive was added at the rate of 8 {mu}mol/l and 12 {mu}mol/l to make mixtures of 60% tall oil methyl ester/40% diesel fuel (TE60) for preparing test fuels. Metallic fuel additives improved properties of biodiesel fuels, such as pour point and viscosity values. Biodiesel fuels were tested in an unmodified direct injection diesel engine at full load condition. Specific fuel consumption of biodiesel fuels increased by 6.00%, however, in comparison with TE60, it showed trend of decreasing with adding of additives. Exhaust emission profile of biodiesel fuels improved. CO emissions and smoke opacity decreased up to 64.28% and 30.91% respectively. Low NOx emission was also observed in general for the biodiesel fuels. 28 refs., 4 figs., 3 tabs.

Process technology for refining crude soybean oil – a product from ...

African Journals Online (AJOL)

Process technology for refining crude soybean oil – a product from soycake meal production in Ghana. ... yield of 83.3 per cent was recorded. Results of quality assessment of the final laboratory refined oil compared favourably with Ghana Standards Board's specification for edible soybean oil. Ghana Journal of Science Vol.

US crude oil, natural gas, and natural gas liquids reserves

International Nuclear Information System (INIS)

1992-01-01

This report presents estimates of proved reserves of crude oil, natural gas, and natural gas liquids as of December 31, 1991, as well as production volumes for the United States, and selected States and State subdivisions for the year 1991. Estimates are presented for the following four categories of natural gas: total gas (wet after lease separation), its two major components (nonassociated and associated-dissolved gas), and total dry gas (wet gas adjusted for the removal of liquids at natural gas processing plants). In addition, two components of natural gas liquids, lease condensate and natural gas plant liquids, have their reserves and production data presented. Also included is information on indicated additional crude oil reserves and crude oil, natural gas, and lease condensate reserves in nonproducing reservoirs. A discussion of notable oil and gas exploration and development activities during 1991 is also presented

Influence of the addition and storage time of crude extract of tea leaves (camellia sinensis l.) toward value of free fatty acid in crude palm oil

Science.gov (United States)

Erwin; Wahifiyah, E.; Hairani, R.; Panggabean, A. S.

2018-04-01

The purpose of this study was to determine the effect of the crude extract of tea leaves (Camellia sinensis L.) and storage time on the content of free fatty acid in palm oil. The dried tea leaves were macerated and concentrated by rotary evaporator. The extract obtained was added to crude palm oil with various added mass of the extract and various storage times. Phytochemical tests indicated the presence of secondary metabolites including alkaloids, triterpenoids, steroids, phenolics and flavonoids. The ANOVA test showed a decrease in free fatty acid content in crude palm oil with the addition of tea leaves extract. The LSD (Least Significant Difference) test showed the best influence on ALB of palm oil is on the total extract mass of 2 grams and the storage time of 20 days.

Generation of biogas using crude glycerin from biodiesel production as a supplement to cattle slurry

Energy Technology Data Exchange (ETDEWEB)

Robra, S.; Neto, J. A. Almeida [Departamento de Ciencias Agrarias e Ambientais, Universidade Estadual de Santa Cruz, Rod. Ilheus/Itabuna km 16 s/n, CEP 45662-000 Ilheus, Bahia (Brazil); Serpa da Cruz, R.; de Oliveira, A.M.; Santos, J.V. [Departamento de Ciencias Exatas e Tecnologicas, Universidade Estadual de Santa Cruz, Rod. Ilheus/Itabuna km 16 s/n, CEP 45662-000 Ilheus, Bahia (Brazil)

2010-09-15

The influence of crude glycerin on biogas production and methane content of the produced biogas was studied, when added to cattle slurry. The experimental design consisted of 5% wt (Gli 5), 10% wt (Gli 10), and 15% wt (Gli 15) of crude glycerin added to cattle slurry, and one control digester without addition of crude glycerin. Anaerobic digestion was carried out in 4 laboratory size CSTR-type biogas digesters with a working volume of 3 L, in semi-continuous regime at mesophilic conditions, over a period of 10 weeks. The highest biogas yields (825.3 mL g{sup -1} and 825.7 mL g{sup -1}, respectively) relative to mass of volatile compounds added, were produced by the treatments Gli 5 and Gli 10. The control treatment produced 268.6 mL g{sup -1}, whereas the treatment Gli 15 produced 387.9 mL g{sup -1}. This low value was due to the breakdown of the process. Compared to the control, methane contents was increased by 9.5%, 14.3%, and 14.6%, respectively, for the treatments Gli 5, Gli 10, and Gli 15. (author)

Crude oil market report

Energy Technology Data Exchange (ETDEWEB)

1985-01-01

Falling demand for refined products and an excess of production capacity are driving world oil prices down further. Competitive price cutting, notably by Mexico, Britain, and the Soviet Union, has left Saudi Arabia the only guardian of a costly pricing discipline in terms of crude oil sales. The current crisis is limited to the producers of crude oil. Refineries are now deciding what, where, and how to buy crude in order to meet the requirements of a slack market place. Saudi Arabia could precipitate a price collapse below $20 per barrel by increasing production volume, but that seems unlikely. 1 figure, 2 tables.

Crude oil pipeline expansion summary

International Nuclear Information System (INIS)

2005-02-01

The Canadian Association of Petroleum Producers has been working with producers to address issues associated with the development of new pipeline capacity from western Canada. This document presents an assessment of the need for additional oil pipeline capacity given the changing mix of crude oil types and forecasted supply growth. It is of particular interest to crude oil producers and contributes to current available information for market participants. While detailed, the underlying analysis does not account for all the factors that may come into play when individual market participants make choices about which expansions they may support. The key focus is on the importance of timely expansion. It was emphasized that if pipeline expansions lags the crude supply growth, then the consequences would be both significant and unacceptable. Obstacles to timely expansion are also discussed. The report reviews the production and supply forecasts, the existing crude oil pipeline infrastructure, opportunities for new market development, requirements for new pipeline capacity and tolling options for pipeline development. tabs., figs., 1 appendix

Optimization of crude oil degradation by Dietzia cinnamea KA1, capable of biosurfactant production.

Science.gov (United States)

Kavynifard, Amirarsalan; Ebrahimipour, Gholamhossein; Ghasempour, Alireza

2016-05-01

The aim of this study was isolation and characterization of a crude oil degrader and biosurfactant-producing bacterium, along with optimization of conditions for crude oil degradation. Among 11 isolates, 5 were able to emulsify crude oil in Minimal Salt Medium (MSM) among which one isolate, named KA1, showed the highest potency for growth rate and biodegradation. The isolate was identified as Dietzia cinnamea KA1 using morphological and biochemical characteristics and 16S rRNA gene sequencing. The optimal conditions were 510 mM NaCl, pH 9.0, 35 °C, and minimal requirement of 46.5 mM NH4 Cl and 2.10 mM NaH2 PO4 . Gravimetric test and Gas chromatography-Mass spectroscopy technique (GC-MS) showed that Dietzia cinnamea KA1 was able to utilize and degrade 95.7% of the crude oil after 5 days, under the optimal conditions. The isolate was able to grow and produce biosurfactant when cultured in MSM supplemented with crude oil, glycerol or whey as the sole carbon sources, but bacterial growth was occurred using molasses with no biosurfactant production. This is the first report of biosurfactant production by D. cinnamea using crude oil, glycerol and whey and the first study to report a species of Dietzia degrading a wide range of hydrocarbons in a short time. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Carotenoid-cleavage activities of crude enzymes from Pandanous amryllifolius.

Science.gov (United States)

Ningrum, Andriati; Schreiner, Matthias

2014-11-01

Carotenoid degradation products, known as norisoprenoids, are aroma-impact compounds in several plants. Pandan wangi is a common name of the shrub Pandanus amaryllifolius. The genus name 'Pandanus' is derived from the Indonesian name of the tree, pandan. In Indonesia, the leaves from the plant are used for several purposes, e.g., as natural colorants and flavor, and as traditional treatments. The aim of this study was to determine the cleavage of β-carotene and β-apo-8'-carotenal by carotenoid-cleavage enzymes isolated from pandan leaves, to investigate dependencies of the enzymatic activities on temperature and pH, to determine the enzymatic reaction products by using Headspace Solid Phase Microextraction Gas Chromatography/Mass Spectrophotometry (HS-SPME GC/MS), and to investigate the influence of heat treatment and addition of crude enzyme on formation of norisoprenoids. Crude enzymes from pandan leaves showed higher activity against β-carotene than β-apo-8'-carotenal. The optimum temperature of crude enzymes was 70°, while the optimum pH value was 6. We identified β-ionone as the major volatile reaction product from the incubations of two different carotenoid substrates, β-carotene and β-apo-8'-carotenal. Several treatments, e.g., heat treatment and addition of crude enzymes in pandan leaves contributed to the norisoprenoid content. Our findings revealed that the crude enzymes from pandan leaves with carotenoid-cleavage activity might provide a potential application, especially for biocatalysis, in natural-flavor industry. Copyright © 2014 Verlag Helvetica Chimica Acta AG, Zürich.

Potential impact of environmental requirements on petroleum products derived from synthetic crude

International Nuclear Information System (INIS)

1997-01-01

Fuel quality proposals regarding gasoline and diesel fuels were discussed. Strict regulations on air emissions will mean changes in transportation fuel specifications which will ultimately impact on the refining industry. As fuel quality requirements become more stringent, refiners will need to look more closely at increasing the use of Canadian synthetic crude as a refinery feed. The fuel quality specifications with the potentially highest impact for the continued use of synthetic crude are those relating to sulphur, aromatics (including benzene), and olefins in gasoline and sulphur, aromatics and cetane in diesel fuel. Synthetic crude has an advantage in terms of gasoline sulphur content. The FCC feed is at a low enough sulphur level to result in gasoline components that would allow refiners to meet final gasoline sulphur levels of less than 100 ppm. In either case, synthetic middle distillate must be upgraded. Options that face the synthetic crude and refining industries are: (1) synthetic crude producers may install the process equipment needed to upgrade the middle distillate portion of their synthetic crude stream, (2) refiners may install equipment to upgrade just the diesel fuel portion of the middle distillate pool and jet fuel, and (3) a joint effort may be made by the two industries. The National Centre for Upgrading Technology (NCUT) and the Western Research Centre of Natural Resources Canada will continue to assist with research into improved catalysts for hydrotreating of middle distillates, and new lower cost processes for upgrading middle distillates from synthetic and conventional crude oils to meet future product requirements. 5 refs., 1 tab

Evaluation of opportunities for heat integration of biomass-based Fischer–Tropsch crude production at Scandinavian kraft pulp and paper mill sites

International Nuclear Information System (INIS)

Ljungstedt, Hanna; Pettersson, Karin; Harvey, Simon

2013-01-01

This study investigates heat integrated production of FT (Fischer–Tropsch) crude, where excess heat from the FT crude plant is delivered to a typical Scandinavian pulp and paper mill that produces fine paper. The sizes of FT crude plants are quantified, when the amount of excess heat from the FT plant exactly matches the heating demand otherwise satisfied by the bark boiler at the mill, considering a number of development pathways at the mill, including various degrees of steam savings and biorefinery options, such as lignin extraction. Performance of integrated production is compared with that of an FT stand-alone plant on the basis of wood fuel-to-FT crude efficiency, GHG (greenhouse gas) emissions balances and FT crude production cost. The results show that there exists a heat integration opportunity for an FT crude plant ranging from 0 up to 350 MW (LHV) of wood fuel depending on the development pathway for the mill. The results indicate higher overall efficiency and a generally lower production cost for the heat integrated, co-located production. Heat integrated production has a larger potential to contribute to GHG emission mitigation, assuming a future generation of grid electricity emitting equal to or less than an NGCC (natural gas combined cycle) power plant. - Highlights: • We investigate opportunities for heat integrated FT crude production at a mill. • Typical kraft pulp and paper mills have a potential for heat integrated production. • We compare the heat integrated production with stand-alone FT crude production. • Higher efficiency and lower production cost for heat integrated production. • Reduction of GHG emissions is strongly dependent on grid electricity emissions

Life cycle water demand coefficients for crude oil production from five North American locations.

Science.gov (United States)

Ali, Babkir; Kumar, Amit

2017-10-15

The production of liquid fuels from crude oil requires water. There has been limited focus on the assessment of life cycle water demand footprints for crude oil production and refining. The overall aim of this paper is address this gap. The objective of this research is to develop water demand coefficients over the life cycle of fuels produced from crude oil pathways. Five crude oil fields were selected in the three North American countries to reflect the impact of different spatial locations and technologies on water demand. These include the Alaska North Slope, California's Kern County heavy oil, and Mars in the U.S.; Maya in Mexico; and Bow River heavy oil in Alberta, Canada. A boundary for an assessment of the life cycle water footprint was set to cover the unit operations related to exploration, drilling, extraction, and refining. The recovery technology used to extract crude oil is one of the key determining factors for water demand. The amount of produced water that is re-injected to recover the oil is essential in determining the amount of fresh water that will be required. During the complete life cycle of one barrel of conventional crude oil, 1.71-8.25 barrels of fresh water are consumed and 2.4-9.51 barrels of fresh water are withdrawn. The lowest coefficients are for Bow River heavy oil and the highest coefficients are for Maya crude oil. Of all the unit operations, exploration and drilling require the least fresh water (less than 0.015 barrel of water per barrel of oil produced). A sensitivity analysis was conducted and uncertainty in the estimates was determined. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Necessity of a Graded Tariff System between Crude Oil and Oil Products

Energy Technology Data Exchange (ETDEWEB)

Kang, B.R. [SK Corporation, Seoul (Korea)

2002-06-01

Even though the graded tariff system between crude oil and oil products has been continuously insisted by oil refining companies since the export and import liberalization of 1997, and its necessity has been admitted by the government, press, and academia, the expanded implementation of the graded tariff system has not been yet realized. Some people says that the graded tariff system between crude oil and oil products is a kind of desperate plans, which oil refining companies suggests to stop the importing companies' rapid growth, so it will eventually restrict the competition of the domestic oil market due to the withering of importing companies. However, the graded tariff system between crude oil and oil products should have been enforced in 1997 as a complementary measure of the import liberalization like other industries or the advanced countries' cases. It is the basic tariff principle that the low tariff is levied on raw materials and the high tariff on final products in order to protect domestic industry. The remaining things are just to form the sympathy and to agree socially for the reorganization of tariff structure in the reasonable way. It is not desirable to make a fool mistake such as a proverb; t is too late to shut the stable door after the horse has bolted. owing to the unreasonable tariff system.

A Canadian refiner's perspective of synthetic crudes

International Nuclear Information System (INIS)

Halford, T.L.; McIntosh, A.P.; Rasmussen

1997-01-01

Some of the factors affecting a refiner's choice of crude oil include refinery hardware, particularly gas oil crackers, products slate and product specifications, crude availability, relative crude price and crude quality. An overview of synthetic crude, the use of synthetic crude combined with other crudes and a comparison of synthetic crude with conventional crude oil was given. The two main users of synthetic crude are basically two groups of refiners, those large groups who use synthetic crude combined with other crudes, and a smaller group who run synthetic crude on specially designed units as a sole feed. The effects of changes in fuel legislation were reviewed. It was predicted that the changes will have a mixed impact on the value of synthetic crude, but low sulphur diesel regulations and gasoline sulphur regulations will make current synthetic crudes attractive. The big future change with a negative impact will be diesel cetane increases to reduce engine emissions. This will reduce synthetic crude attractiveness due to distillate yields and quality and high gas oil yields. Similarly, any legislation limiting aromatics in diesel fuel will also make synthetic crudes less attractive. Problems experienced by refiners with hardware dedicated to synthetic crude (salt, naphthenic acid, fouling, quality variations) were also reviewed. 3 tabs

Microwave-assisted and carbonaceous catalytic pyrolysis of crude glycerol from biodiesel waste for energy production

International Nuclear Information System (INIS)

Ng, Jo-Han; Leong, Swee Kim; Lam, Su Shiung; Ani, Farid Nasir; Chong, Cheng Tung

2017-01-01

Highlights: • Crude glycerol is pyrolysed catalytically via microwave irradiation to produce bioenergy. • Carbonaceous catalyst elevates pyrolysis temperature and promotes selectivity towards H_2 production. • Synthesis gas consisting of mainly H_2 and CH_4 was predominantly produced at long residence time and high temperature. • Production of bio-oil consisting of oxygenated compounds peaks at intermediate carrier gas flow rate. • Energy profit analysis shows positive energy gained with increasing residence time and decreasing reaction temperature. - Abstract: Biodiesel proliferation as a sustainable fuel has led to a glut of crude glycerol as co-product. This scenario made a previously lucrative co-product in the food and pharmaceutical sectors into a bioresource waste. The present study investigates the utilisation of a microwave-assisted pyrolysis technique to convert crude glycerol from biodiesel waste into usable bioenergy source. Operating conditions ranged from a temperature of 300–800 °C at carrier gas flow rates of 100–2000 mL/min, with the effects of carbonaceous catalyst on the selectivity of reaction pathway being investigated. Within the aforementioned conditions, the proportion of products phases is mainly dependent on the residence time inside the quartz reactor, followed by the reaction temperature. This is due to the combined factors of the reaction sequence and provision of activation energy to change product phases. The third factor of carbonaceous catalyst shows a predisposition towards hydrogen gas selectivity, leading to a lower overall gaseous product mass when factoring in products from all phases. An analysis of the energy content revealed that overall energy profit increases with decreasing temperature and increasing residence time. This concurs with solid energy content increasing in the same conditions, while it increases for liquid and gaseous products with decreasing temperature and flow rate, respectively. The

The Use of Crude Shrimp Shell Powder for Chitinase Production by Serratia marcescens WF

Directory of Open Access Journals (Sweden)

Jesús E. Mejía-Saulés

2006-01-01

Full Text Available From 102 Serratia marcescens strains screened, 57 strains showed chitinase activity and Serratia marcescens WF showed the highest chitinolytic activity so this strain was selected for further study on the use of crude shrimp waste for chitinase production. The concentration of crude shrimp shell content at 10–70 g/L, incubation temperature of 28–37 °C, pH=6–9, and time 24–96 h on kinetics of chitinase production by S. marcescens WF were evaluated. The maximal chitinase production related to process variables was obtained with the second order polynomial model: dry shrimp shell powder at 6 %, pH=6.5, temperature of 28 °C during fermentation for up to 72 h.

Process optimization and analysis of product inhibition kinetics of crude glycerol fermentation for 1,3-Dihydroxyacetone production.

Science.gov (United States)

Dikshit, Pritam Kumar; Padhi, Susant Kumar; Moholkar, Vijayanand S

2017-11-01

In present study, statistical optimization of biodiesel-derived crude glycerol fermentation to DHA by immobilized G. oxydans cells over polyurethane foam is reported. Effect of DHA (product) inhibition on crude glycerol fermentation was analyzed using conventional biokinetic models and new model that accounts for both substrate and product inhibition. Optimum values of fermentation parameters were: pH=4.7, temperature=31°C, initial substrate concentration=20g/L. At optimum conditions, DHA yield was 89% (17.83g/L). Effect of product inhibition on fermentation was trivial for DHA concentrations ≤30g/L. At higher concentrations (≥50g/L), kinetics and yield of fermentation showed marked reduction with sharp drop in V max and K S values. Inhibition effect was more pronounced for immobilized cells due to restricted transport of fermentation mixture across polyurethane foam. Retention of fermentation mixture in immobilized matrix resulted in higher localized DHA concentration that possibly enhanced inhibition effect. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biosurfactant production by Mucor circinelloides on waste frying oil and possible uses in crude oil remediation.

Science.gov (United States)

Hasanizadeh, Parvin; Moghimi, Hamid; Hamedi, Javad

2017-10-01

Biosurfactants are biocompatible surface active agents which many microorganisms produce. This study investigated the production of biosurfactants by Mucor circinelloides. The effects of different factors on biosurfactant production, including carbon sources and concentrations, nitrogen sources, and iron (II) concentration, were studied and the optimum condition determined. Finally, the strain's ability to remove the crude oil and its relationship with biosurfactant production was evaluated. The results showed that M. circinelloides could reduce the surface tension of the culture medium to 26.6 mN/m and create a clear zone of 12.9 cm diameter in an oil-spreading test. The maximum surface tension reduction was recorded 3 days after incubation. The optimum condition for biosurfactant production was achieved in the presence of 8% waste frying oil as a carbon source, 2 g/L yeast extract as a nitrogen source, and 0.01 mM FeSO 4 . M. circinelloides could consume 8% waste frying oil in 5 days of incubation, and 87.6% crude oil in 12 days of incubation. A direct correlation was observed between oil degradation and surface tension reduction in the first 3 days of fungal growth. The results showed that the waste frying oil could be recommended as an inexpensive oily waste substance for biosurfactant production, and M. circinelloides could have the potential to treat waste frying oil. According to the results, the produced crude biosurfactant or fungal strain could be directly used for the mycoremediation of crude oil contamination in oil fields.

[Prediction of the side-cut product yield of atmospheric/vacuum distillation unit by NIR crude oil rapid assay].

Science.gov (United States)

Wang, Yan-Bin; Hu, Yu-Zhong; Li, Wen-Le; Zhang, Wei-Song; Zhou, Feng; Luo, Zhi

2014-10-01

In the present paper, based on the fast evaluation technique of near infrared, a method to predict the yield of atmos- pheric and vacuum line was developed, combined with H/CAMS software. Firstly, the near-infrared (NIR) spectroscopy method for rapidly determining the true boiling point of crude oil was developed. With commercially available crude oil spectroscopy da- tabase and experiments test from Guangxi Petrochemical Company, calibration model was established and a topological method was used as the calibration. The model can be employed to predict the true boiling point of crude oil. Secondly, the true boiling point based on NIR rapid assay was converted to the side-cut product yield of atmospheric/vacuum distillation unit by H/CAMS software. The predicted yield and the actual yield of distillation product for naphtha, diesel, wax and residual oil were compared in a 7-month period. The result showed that the NIR rapid crude assay can predict the side-cut product yield accurately. The near infrared analytic method for predicting yield has the advantages of fast analysis, reliable results, and being easy to online operate, and it can provide elementary data for refinery planning optimization and crude oil blending.

Action of crude Radix Aconiti Lateralis (Fuzi) and its processed products on splenic lymphocytes growth investigated by microcalorimetry

International Nuclear Information System (INIS)

Liu, Tiantian; Zhao, Yanling; Wang, Jiabo; Zhou, Xu; Sun, Zhiyong; Zheng, Quanfu; Li, Ruisheng; Zhang, Ping; Li, Jianyu; Song, Xueai; Xiao, Xiaohe

2013-01-01

Highlights: • This article investigated the effects of crude Radix Aconiti Lateralis and its processed products on splenic lymphocytes. • The results showed that bioeffects of crude Radix Aconiti Lateralis could be obtained by thermodynamic parameters. • This study gave the hint that the microcalorimetry is a useful tool to estimate the efficiency and toxicity of medicine. - Abstract: Using the TAM air isothermal microcalorimeter, the HFP–time curves of splenic lymphocytes growth were measured, and the effects of crude Radix Aconiti Lateralis and its processed products including Yanfuzi, Danfupian, Baifupian on splenic lymphocytes growth were investigated. Some quantitative information, such as k, P max etc. was obtained from the HFP–time curves. The results revealed that crude Radix Aconiti Lateralis and Yanfuzi had inhibitory effect on mice splenic lymphocytes growth: crude Radix Aconiti Lateralis with IC 50 of 18 mg mL −1 showed stronger inhibitory effect than Yanfuzi with IC 50 of 32 mg mL −1 . Danfupian and Baifupian promoted splenic lymphocytes growth: Baifupian with EC 50 of 25 mg mL −1 showed a little stronger promotion effect than Danfupian with EC 50 of 28 mg mL −1 . The result may be related to their toxicity and we could evaluate different bioeffects of crude Radix Aconiti Lateralis and its processed products on splenic lymphocytes growth from microcalorimetric measurement

Production of jet fuel using heavy crude oil; Producao de combustiveis de aviacao a partir de petroleos pesados

Energy Technology Data Exchange (ETDEWEB)

Om, Neyda [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica; Cavado, Alberto; Reyes, Yordanka [Centro de Pesquisas do Petroleo, Cidade de Havana (Cuba); Dominguez, Zulema [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE)

2004-07-01

The production of heavy crude oils increased in the last years in the world. Crude oils with high density, viscosity, acidity and sulfur, nitrogen, metals and asphaltenes contents, by the others hand, low stability and low product quality. The challenger of many refiners is find solutions to refine the heavy crude oils, and produce fuels with certify quality, such as Jet Fuel. The principal aviation technique on the world work with gas turbines engines feted for jet fuel (JET A1). The quality specifications of this fuel are establish by International Norms: ASTM-1655, DEF STAN 91-91-3 (DERD 2494) and joint Fuelling System Check List. The world technologies to obtain jet fuel from mixtures of heavy crude oil with middle crude oils are: Atmospheric distillation, with a posterior hydrogenation and finally the additivation. Studies carried out have demonstrates that the Cubans heavy crude oils is characterized for having API less than 10, raised viscosity, high sulfur content (>6%) and asphaltenes content (more than 15%). These properties provide to its derivatives of low quality. This paper define the characteristic of Cuban heavy crude oil, the technology and operational conditions to produce jet fuel (Jet A1) and the quality of fuel produced. (author)

Mitigation of naphthenate related production upsets in high TAN (Total Acid Number) crude oil

Energy Technology Data Exchange (ETDEWEB)

Ostojic, Nik [Maersk Oil, Copenhagen (Denmark); Vijn, Pieter; Reiners, Robert [Champion Technologies Europe BV, Delden (Netherlands)

2012-07-01

This paper describes a strategy for prediction, evaluation and mitigation of calcium naphthenate related production problems. Developing fields with acidic crude in the North Sea, West Africa, Bohai Bay (China) and Brazil is becoming more common in recent years. The high acid crude contains a considerable amount of naphthenic acids, typically having a Total Acid Number (TAN) higher than 0.5 mg KOH/g. Formation of either hard type 'calcium naphthenate precipitates' or soft type 'sodium carboxylate/emulsions' during crude oil production can lead to severe flow assurance and separation problems. In severe cases this may lead to production shutdowns to clean-up the equipment. A number of different naphthenate mitigation approaches have been published but no one particular approach is considered to be the most efficient as it depends significantly on the particular field conditions. Initially, this problem was addressed by deploying large volumes of (usually organic) acid, but more recently high efficiency low dose naphthenate inhibitors have been introduced. For predicting naphthenate scaling potential, methods were developed to determine the concentration of 1230 Dalton naphthenic tetra acid (ARN acids) in either deposit or crude oil and this information can be used to locate and potentially isolate the problem to a certain reservoir. Also, methods were developed to design suitable low dose naphthenate inhibitors. As these inhibitors are field tested, monitoring is required to ensure the product is performing most efficiently. In cases of tight emulsions however, this is less difficult as the oil dehydration and water quality is affected instantly. Methods were developed to allow monitoring of the calcium naphthenate deposition in field trails, thus allow trending and evaluation of the chemicals performance. After detailed analyses and discussions of the developed methods, a North Sea case history is presented reviewing several years of treating

US crude oil, natural gas, and natural gas liquids reserves, 1992 annual report

Energy Technology Data Exchange (ETDEWEB)

1993-10-18

This report presents estimates of proved reserves of crude oil, natural gas, and natural gas liquids as of December 31, 1992, as well as production volumes for the United States, and selected States and State subdivisions for the year 1992. Estimates are presented for the following four categories of natural gas: total gas (wet after lease separation), its two major components (nonassociated and associated-dissolved gas), and total dry gas (wet gas adjusted for the removal of liquids at natural gas processing plants). In addition, two components of natural gas liquids, lease condensate and natural gas plant liquids, have their reserves and production data presented. Also included is information on indicated additional crude oil reserves and crude oil, natural gas, and lease condensate reserves in nonproducing reservoirs. A discussion of notable oil and gas exploration and development activities during 1992 is provided.

US crude oil, natural gas, and natural gas liquids reserves, 1992 annual report

International Nuclear Information System (INIS)

1993-01-01

This report presents estimates of proved reserves of crude oil, natural gas, and natural gas liquids as of December 31, 1992, as well as production volumes for the United States, and selected States and State subdivisions for the year 1992. Estimates are presented for the following four categories of natural gas: total gas (wet after lease separation), its two major components (nonassociated and associated-dissolved gas), and total dry gas (wet gas adjusted for the removal of liquids at natural gas processing plants). In addition, two components of natural gas liquids, lease condensate and natural gas plant liquids, have their reserves and production data presented. Also included is information on indicated additional crude oil reserves and crude oil, natural gas, and lease condensate reserves in nonproducing reservoirs. A discussion of notable oil and gas exploration and development activities during 1992 is provided

Jet A and low sulphur diesel production and blending experience in a synthetic crude-rich environment

International Nuclear Information System (INIS)

1997-01-01

The Sunoco Sarnia Refinery has produced large volumes of high quality Jet A and Low Sulphur Diesel without major capital investment. They have done this by blending the synergy between hydrocracked and synthetic-based distillate stocks. The Sunoco Sarnia Refinery has two crude units, a Catalytic Cracker, a Hydrocracker and a Hydrogen unit, two reformers, Alkylation and BTX units. It also has the usual facilities such as gas plants, gasoline treater, and a naphtha pre-treater for former feed and an amine sulphur unit. Refinery distillate products, crudes used, components used for blending the distillate products, cost of the facilities and average production of each product were reviewed. A schematic of the Sarnia Refinery Distillate Production Facility was provided. 1 tab., 1 fig

Anaerobic digestion of crude glycerol from biodiesel manufacturing using a large-scale pilot plant: methane production and application of digested sludge as fertilizer.

Science.gov (United States)

Baba, Yasunori; Tada, Chika; Watanabe, Ryoya; Fukuda, Yasuhiro; Chida, Nobuyoshi; Nakai, Yutaka

2013-07-01

This report is the first to consider methane production energy balance from crude glycerol at a practical rather than a laboratory scale. Crude glycerol was added to the plant progressively at between 5 and 75 L glycerol/30 m(3)-day for 1.5 years, and the energy balance was positive at a loading rate of 30 L glycerol/30 m(3)-day (1 ml/L-day). At this loading rate over one year, an energy output equivalent to 106% of the energy input was achieved. The surplus energy was equivalent to transport for 1200 km, so the proper feedstock-transportation distance was within a 12.5-km radius of the biogas plant. In addition, the digested sludge contained fertilizer components (T-N: 0.11%, P2O5: 0.036%, K2O: 0.19%) that increased grass yield by 1.2 times when applied to grass fields. Thus, crude glycerol is an attractive bioresource that can be used as both a feedstock for methane production and a liquid fertilizer. Copyright © 2013 Elsevier Ltd. All rights reserved.

Causes for an asymmetric relation between the price of crude oil and refined petroleum products

International Nuclear Information System (INIS)

Kaufmann, R.K.; Laskowski, C.

2005-01-01

We revisit the issue of asymmetries in the relation between the price of crude oil and refined petroleum products in the United States. An econometric analysis of monthly data indicates that the asymmetric relationship between the price of crude oil and motor gasoline is generated by refinery utilization rates and inventory behavior. The asymmetric relation between the price of crude oil and home heating oil probably is generated by contractual arrangements between retailers and consumers. Together, these results imply that price asymmetries may be generated by efficient markets. Under these conditions, there is little justification for policy interventions to reduce or eliminate price asymmetries in motor gasoline and home heating oil markets. (author)

Crude oil growth impact on pipelines

International Nuclear Information System (INIS)

Devries, O.

2005-01-01

This paper provided an outline of crude oil production and supply in Canada. Details of oil sands projects in Athabasca, Cold Lake and Peace River were presented. A chart of oil sands growth by major project was provided. A list of new emerging oil sands crude types was also presented along with details of a synthetic bitumen blending synergy. Maps of Western Canadian crude oil markets were provided, along with details of refinery and market demand by crude type. Various pipeline alternatives to new markets were examined, with reference to Enbridge Pipeline's supply and capacity. Details of the Hardisty to U.S Gulf Coast Pipeline and the Edmonton to Prince Rupert Pipeline and its terminal and dock facilities were presented. It was concluded that pipeline capacity and seasonal factors will influence market demand, while linefill, crude types and the quality of the product will influence operational strategies. tabs., figs

Crude incompatibility problems at heavy crude unit desalter

International Nuclear Information System (INIS)

Kirmani, Z.; Khurshid, A.; Alam, N.; Gul, S.; Ahmed, N.

2009-01-01

Attock Refinery Limited (ARL) is based at Rawalpindi, Pakistan and operates a 40,000 Barrels per Stream Day (BPSD) refinery. The Heavy Crude Unit (HCU) of ARL is a fully integrated two-stage 10,000 BPSD Atmospheric and 5,700 BPSD Vacuum Distillation Unit. A 3-stage desalter designed to reduce salt and BS and W content from 2,000 parts per thousand barrels (PTB) and 2% to less than 5 PTB and 0.1% respectively, is part of HCU. The feedstock is a composite blend of 14 local Heavy Crudes received at the Refinery. Although in the past this desalter had been giving good performance, over the last one year, period since August 2005, at least nine shutdowns of the unit took place due to salt slippage and consequential tube leakages at the overhead Crude-Naphtha vapor Heat Exchanger where partial condensation of naphtha takes place. Final condensation is achieved in trim condenser. High salted water carry-over with the crude caused increased hydrolysis, formation of Hydrochloric acid and increase of tail water chlorides. Salt contents at the outlet of third desalter at times increased up to 400 PTB with 3.2% BS and W during the above mentioned upsets, as compared to normal 5-10 PTB. Fallout from this loss of desalter control was the creation of large quantities of slop due to draining of strong water oil emulsion from the desalters. Individual crudes of the blend were analyzed for affinity of water and emulsion stability. It was observed that 3 of the 14 crudes formed very strong while the remaining crudes formed weak oil water emulsion, which easily separated water from oil in desalter without any operational problem. Study was further narrowed down to one crude evaluation. Alkaline earth metallic naphthenate surfactants were detected and isolated as responsible for the strong water oil and sediments emulsion. The isolated crude was next withdrawn from the Heavy Crude blend. As soon as it was isolated and its ratio in heavy crude tank came down to 0.7 %, the problem began

In situ ruminal crude protein degradability of by-products from cereals, oilseeds and animal origin

NARCIS (Netherlands)

Habib, G.; Khan, N.A.; Ali, M.; Bezabih, M.

2013-01-01

The aim of this study was to establish a database on in situ ruminal crude protein (CP) degradability characteristics of by-products from cereal grains, oilseeds and animal origin commonly fed to ruminants in Pakistan and South Asian Countries. The oilseed by-products were soybean meal, sunflower

Bitumen still seen as potential anchor on crude prices

International Nuclear Information System (INIS)

Jaremko, G.

2001-01-01

Researchers at the Canadian Energy Research Institute have released a 225-page technical report on downstream oil-refining markets entitled 'Markets for Canadian bitumen-based feedstock'. The report claims that 22 of 27 refineries that buy western Canadian production are not planning to improve their ability to process heavy grades of oil any time soon. Instead, investments will focus on complying with environmental requirements for reformulated refined products, particularly to eliminate sulphur impurities in gasoline and diesel fuel. Another focus will be to upgrade raw bitumen output into synthetic crude. It was shown that over the next 7 years, Canadian and U.S. oil markets have the potential to increase growth in bitumen production from 244,000 barrels per day (bpd) to 555,000 bpd. The potential for additional, upgraded synthetic crude oil is even greater, from 450,000 bpd to 806,000 bpd. Increasing the output of synthetic crude oil is considered to be an effective way to reduce North America's reliance on imported oil. Untreated, discount-priced bitumen can replace diminishing Canadian and U.S. production of refinery-ready light oil. The report projects that a US$1-per-barrel discount for Canadian heavy oil would generate sales of 140,000 barrels daily. The effect of a $1 discount would be almost twice as great for synthetic crude oil. Heavy oil sales rely greatly on maintaining a discount off prices for light grades. A $1-per-barrel premium could destroy demand for bitumen-based blends. Moody's Investors Service claims that deep discounting reflects global market conditions, risking Canadian production of heavy oil grades and seasonal lows in demand for bitumen as a raw material for asphalt

Biosurfactant production from marine hydrocarbon-degrading consortia and pure bacterial strains using crude oil as carbon source

Directory of Open Access Journals (Sweden)

Eleftheria eAntoniou

2015-04-01

Full Text Available Biosurfactants (BS are green amphiphilic molecules produced by microorganisms during biodegradation, increasing the bioavailability of organic pollutants. In this work, the BS production yield of marine hydrocarbon degraders isolated from Elefsina bay in Eastern Mediterranean Sea has been investigated. The drop collapse test was used as a preliminary screening test to confirm biosurfactant producing strains or mixed consortia. The community structure of the best consortia based on the drop collapse test was determined by 16S-rDNA pyrotag screening. Subsequently, the effect of incubation time, temperature, substrate and supplementation with inorganic nutrients, on biosurfactant production, was examined. Two types of BS - lipid mixtures were extracted from the culture broth; the low molecular weight BS Rhamnolipids and Sophorolipids. Crude extracts were purified by silica gel column chromatography and then identified by thin layer chromatography (TLC and Fourier transform infrared spectroscopy (FT-IR. Results indicate that biosurfactant production yield remains constant and low while it is independent of the total culture biomass, carbon source, and temperature. A constant BS concentration in a culture broth with continuous degradation of crude oil implies that the BS producing microbes generate no more than the required amount of biosurfactants that enables biodegradation of the crude oil. Isolated pure strains were found to have higher specific production yields than the complex microbial marine community-consortia. The heavy oil fraction of crude oil has emerged as a promising substrate for BS production (by marine BS producers with fewer impurities in the final product. Furthermore, a particular strain isolated from sediments, Paracoccus marcusii, may be an optimal choice for bioremediation purposes as its biomass remains trapped in the hydrocarbon phase, not suffering from potential dilution effects by sea currents.

Boom times : Canada's crude petroleum industry : analysis in brief

International Nuclear Information System (INIS)

Rowat, M.R.

2006-01-01

This document examined the trends in crude oil prices, the production and exports of Canada's crude petroleum industry, and Canada's imports of crude petroleum. As an exporter and importer of crude oil, Canada's petroleum industry is currently experiencing economic prosperity as a result of high oil prices combined with high global demand for oil. This document reviewed industry activity for 2005 and addressed the reasons for the first decline in Canadian crude oil production in 6 years. A quick review of soaring crude oil prices, supply and shortages was also presented. A review of exports revealed that since 1995, the United States has received 99 per cent of Canadian exports. Although production activity is occurring in 7 provinces, the biggest participant is Alberta, followed by Saskatchewan. In 2005, Canada produced 136.4 million cubic metres of crude petroleum, of which two-thirds came from Alberta. Saskatchewan contributed 18 per cent of total Canadian crude oil production, while offshore oil rigs in Newfoundland and Labrador contributed 13 per cent. The vast oil sands resource accounted for 42 per cent of the province's total production. Alberta oil export is piped entirely into the United States. In 2005, even with a slight drop in exports, Canadian oil exporters received $30 billion for their products, up from $25 billion the year before. Canada also supplied nearly 10 per cent of the American crude oil needs. According to the National Energy Board, Canadian refineries are approaching capacity. Canada's 19 refineries, which have a capacity of 320,000 cubic metres per day, operated at 92 per cent of capacity in 2005 to meet the needs of the domestic market. More imported petroleum was refined than Canadian sourced petroleum. In 2005, the gas and oil industry saw historically high profits, taxes paid and investments. 6 refs., 5 figs

How is the international price of a particular crude determined?

International Nuclear Information System (INIS)

Hagen, Ronald

1994-01-01

If crude oil or oil products are not the final item of consumption, then oil is not bought or sold on any basis other than its contribution to the final product. The markets of oil products are thus 'derived' from more basic demands, and prices are determined by what they contribute to the costs of producing final products or commodities. Similarly, the value of a crude oil is derived from the value of the petroleum products it yields. This paper attempts to show how differences in crude oil prices seem to occur. The results should be of interest to producers of crude oil, since they will demonstrate how the marketability of their products might vary. (author)

Production Costs of Alternative Transportation Fuels. Influence of Crude Oil Price and Technology Maturity

Energy Technology Data Exchange (ETDEWEB)

Cazzola, Pierpaolo; Morrison, Geoff; Kaneko, Hiroyuki; Cuenot, Francois; Ghandi, Abbas; Fulton, Lewis

2013-07-01

This study examines the production costs of a range of transport fuels and energy carriers under varying crude oil price assumptions and technology market maturation levels. An engineering ''bottom-up'' approach is used to estimate the effect of the input cost of oil and of various technological assumptions on the finished price of these fuels. In total, the production costs of 20 fuels are examined for crude oil prices between USD 60 and USD 150 per barrel. Some fuel pathways can be competitive with oil as their production, transport and storage technology matures, and as oil price increases. Rising oil prices will offer new opportunities to switch to alternative fuels for transport, to diversify the energy mix of the transport sector, and to reduce the exposure of the whole system to price volatility and potential distuption of supply. In a time of uncertainty about the leading vehicle technology to decarbonize the transport sector, looking at the fuel cost brings key information to be considered to keep mobility affordable yet sustainable.

Mercury in Canadian crude oil

International Nuclear Information System (INIS)

Hollebone, B.P.

2005-01-01

Estimates for average mercury concentrations in crude oil range widely from 10 ng/g of oil to 3,500 ng/g of oil. With such a broad range of estimates, it is difficult to determine the contributions of the petroleum sector to the total budget of mercury emissions. In response to concerns that the combustion of petroleum products may be a major source of air-borne mercury pollution, Environment Canada and the Canadian Petroleum Products Institute has undertaken a survey of the average total mercury concentration in crude oil processed in Canadian refineries. In order to calculate the potential upper limit of total mercury in all refined products, samples of more than 30 different types of crude oil collected from refineries were measured for their concentration of mercury as it enters into a refinery before processing. High temperature combustion, cold vapour atomic absorption and cold vapour atomic fluorescence were the techniques used to quantify mercury in the samples. The results of the study provide information on the total mass of mercury present in crude oil processed in Canada each year. Results can be used to determine the impact of vehicle exhaust emissions to the overall Canadian mercury emission budget. 17 refs., 2 tabs., 2 figs

Evaluation of the crude oil viscosity variation in function of the demulsifiers addition; Avaliacao da variacao da viscosidade de oleo cru em funcao da adicao de desemulsificante

Energy Technology Data Exchange (ETDEWEB)

Lopes, Jansen M.; Lucas, Elisabete F. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Inst. de Macromoleculas]. E-mail: elucas@ima.ufrj.br; Neves, Guilherme B.M. [COMAB Especialidades Quimicas Ltda., Rio de Janeiro, RJ (Brazil)]. E-mail: tecnico@comabrio.com

2003-07-01

One way of improving well production is the addition of demulsifier already in the gas lift. This is due to the apparent viscosity of water-in-oil emulsions being higher than apparent viscosity of crude oil, which in turn is higher than the apparent viscosity of an water-in-oil dual phase admixture and is also higher than the apparent viscosity of an oil-in-water emulsion. However, there are some situations where, in order to obtain separate flows of oil and water phases, demulsifier should be added in specific amounts in order to promote the desired phase separation. In heavy oils water and oil phase separation may be hard to obtain, however, the right demulsifier amount may imply in a considerable decrease in petroleum viscosity even without the appearance of two phases, making the flow easier. This work has evaluated the viscosity of a heavy crude having API degree 14 and BSW 52%, as a function of the addition of different amounts of DEMTROL BR 67, manufactured by Dow Quimica/Comab, Brazil, as demulsifier. (author)

California demand and supply of crude oil: An econometric analysis with projections to 2000

International Nuclear Information System (INIS)

Ibegbulam, B.N.

1991-01-01

Forecast of California domestic crude oil supply requires the forecasts of California crude oil production and supply from Alaska. Future California crude oil production is forecast with an econometric model that postulates production as a function of reserves and reserves as a function of crude oil prices and exploration and development costs. Future supplies from Alaska are obtained by subtracting forecasts of Alaskan crude oil demand and shipments to the States of Hawaii, Oregon, and Washington from Alaskan North Slope crude oil production forecasts. A two-stage process was used to forecast future California crude oil demand. In the first stage, the demand for refined crude oil products was predicted with a single-equation double logarithmic rational-expectations dynamic model. In the second stage, the total demands obtained in the first stage were converted into a crude oil equivalent. It was found that the current surplus of domestic crude oil in California will end in 1994. Thereafter, California crude oil imports will sharply increase

Optimizing Microwave-assisted Crude Butter Extraction from Carabao Mango (Mangifera indica Kernels

Directory of Open Access Journals (Sweden)

Edgardo V. Casas

2015-12-01

Full Text Available Carabao mangoes are among the highly produced fruit crops in the Philippines. The processing and consumption of carabao mangoes leave a significant amount of waste seeds. Mango kernel butter extracted from waste seed kernels is a potential additive to cosmetic products or as a cocoa butter substitute. This study determined the pretreatment conditions that produce optimum yield prior to the mechanical extraction of the crude butter. Moreover, this study provided a general sensory evaluation of the finished product. Microwave power (160, 500, and 850 W, microwave exposure time (2.0, 3.5, and 5.0 min, and size levels (1.5, 3.0, and 4.5 mm were tested for their effects on the yield of the mechanically extracted crude butter in wet basis percentage. The optimization procedures resulted to optimum pretreatment conditions of 160 W, 4.25 min, and 1.5 mm. Size level was the most significant factor in the crude butter yield. Sensory evaluation of the crude butter extracted at optimum pretreatment conditions through acceptance test by a test panel resulted to below neutral scores in visual appearance and odor, and above neutral score in texture, indicating the potential of mango butter as a good substitute to cocoa butter in cosmetic products.

The crude petroleum and natural gas industry : 1996

International Nuclear Information System (INIS)

1997-01-01

Statistics regarding Canada's crude oil and natural gas industry for 1996 were presented. Data presentation was in tabular form, the topics being exploration and development, synthetic crude oil reserves, crude oil production and movements by source, natural gas production, drilling completions, net cash expenditures of the petroleum industry, and total sales of natural gas by province. Some of the noteworthy highlights for 1996 were: (1) 14,600 new wells were drilled, the highest number ever recorded, (2) capital investment was over $13 billion, (3) 148 companies were involved in mergers and acquisitions, (4) value of marketable production of oil, natural gas and natural gas by-products topped $30 billion, (5) Empress pipelines began operations of the first new major oil pipeline from Western Canada in 45 years, (6) the Hibernia offshore crude oil facility was completed, (7) Sable Island offshore energy projects applications were filed, and (8) the development of the Terra Nova, Whitehorse and Hebron fields was announced. 8 tabs

Down-hole catalytic upgrading of heavy crude oil

Energy Technology Data Exchange (ETDEWEB)

Weissman, J.G.; Kessler, R.V.; Sawicki, R.A.; Belgrave, J.D.M.; Laureshen, C.J.; Mehta, S.A.; Moore, R.G.; Ursenbach, M.G. [University of Calgary, Calgary, AB (Canada). Dept. of Chemical and Petroleum Engineering

1996-07-01

Several processing options have been developed to accomplish near-well bore in-situ upgrading of heavy crude oils. These processes are designed to pass oil over a fixed bed of catalyst prior to entering the production well, the catalyst being placed by conventional gravel pack methods. The presence of brine and the need to provide heat and reactant gases in a down-hole environment provide challenges not present in conventional processing. These issues were addressed and the processes demonstrated by use of a modified combustion tube apparatus. Middle-Eastern heavy crude oil and the corresponding brine were used at the appropriate reservoir conditions. In-situ combustion was used to generate reactive gases and to drive fluids over a heated sand or catalysts bed, simulating the catalyst contacting portion of the proposed processes. The heavy crude oil was found to be amenable to in-situ combustion at anticipated reservoir conditions, with a relatively low air requirement. Forcing the oil to flow over a heated zone prior to production results in some upgrading of the oil, as compared to the original oil, due to thermal effects. Passing the oil over a hydroprocessing catalyst located in the heated zone results in a product that is significantly upgraded as compared to either the original oil or thermally processed oil. Catalytic upgrading is due to hydrogenation and the results in about a 50% sulfur removal and an 8{degree} API gravity increase. Additionally, the heated catalyst was found to be efficient at converting CO to additional H{sub 2}. While all of the technologies needed for a successful field trial of in-situ catalytic upgrading exist, a demonstration has yet to be undertaken. 27 refs., 5 figs., 5 tabs.

The crude petroleum and natural gas industry, 1995

International Nuclear Information System (INIS)

1996-01-01

A compilation of data regarding the crude petroleum and natural gas industry was presented. This industry includes establishments engaged in exploration for, or production of petroleum or natural gas from wells or tar sands. Data presented in this publication include: the supply and disposition of crude oil and natural gas, operating and capital expenditures of approximately 500 companies of the oil and natural gas industry, drilling completions, and crude oil and natural gas reserves. Data about the oil sands industry is reported in another volume. Much of the data was obtained from the Canadian Association of Petroleum Producers. Overall, in 1995 Canadian natural gas production rose 6.7%; exports of crude oil rose 7.7%. 8 tabs., 2 figs

Heavy oils processing materials requirements crude processing

Energy Technology Data Exchange (ETDEWEB)

Sloley, Andrew W. [CH2M Hill, Englewood, CO (United States)

2012-07-01

Over time, recommended best practices for crude unit materials selection have evolved to accommodate new operating requirements, feed qualities, and product qualities. The shift to heavier oil processing is one of the major changes in crude feed quality occurring over the last 20 years. The three major types of crude unit corrosion include sulfidation attack, naphthenic acid attack, and corrosion resulting from hydrolyzable chlorides. Heavy oils processing makes all three areas worse. Heavy oils have higher sulfur content; higher naphthenic acid content; and are more difficult to desalt, leading to higher chloride corrosion rates. Materials selection involves two major criteria, meeting required safety standards, and optimizing economics of the overall plant. Proper materials selection is only one component of a plant integrity approach. Materials selection cannot eliminate all corrosion. Proper materials selection requires appropriate support from other elements of an integrity protection program. The elements of integrity preservation include: materials selection (type and corrosion allowance); management limits on operating conditions allowed; feed quality control; chemical additives for corrosion reduction; and preventive maintenance and inspection (PMI). The following discussion must be taken in the context of the application of required supporting work in all the other areas. Within that context, specific materials recommendations are made to minimize corrosion due to the most common causes in the crude unit. (author)

Methane production from cattle manure supplemented with crude glycerin from the biodiesel industry in CSTR and IBR.

Science.gov (United States)

Castrillón, L; Fernández-Nava, Y; Ormaechea, P; Marañón, E

2013-01-01

The aim of the present research work was to optimise biogas production from cattle manure by adding crude glycerin from the biodiesel industry. For this purpose, 6%v/v crude glycerin (the optimum amount according to previous research) was added to ground manure and the mixture was sonicated to enhance biodegradability prior to anaerobic co-digestion at 55 °C. Two different reactors were used: continuously stirred (CSTR) and induced bed (IBR). The methanol and pure glycerin contents of the crude glycerin used in this study were 5.6% and 49.4% (w/w), respectively. The best results when operating in CSTR were obtained for an organic loading rate (OLR) of 5.4 kg COD/m(3) day, obtaining 53.2m(3) biogas/t wet waste and 80.7% COD removal. When operating in IBR, the best results were obtained for an OLR of 6.44 kg COD/m(3)day, obtaining 89.6% COD removal and a biogas production of 56.5m(3)/t wet waste. Copyright © 2012 Elsevier Ltd. All rights reserved.

Method to upgrade bio-oils to fuel and bio-crude

Science.gov (United States)

Steele, Philip H; Pittman, Jr., Charles U; Ingram, Jr., Leonard L; Gajjela, Sanjeev; Zhang, Zhijun; Bhattacharya, Priyanka

2013-12-10

This invention relates to a method and device to produce esterified, olefinated/esterified, or thermochemolytic reacted bio-oils as fuels. The olefinated/esterified product may be utilized as a biocrude for input to a refinery, either alone or in combination with petroleum crude oils. The bio-oil esterification reaction is catalyzed by addition of alcohol and acid catalyst. The olefination/esterification reaction is catalyzed by addition of resin acid or other heterogeneous catalyst to catalyze olefins added to previously etherified bio-oil; the olefins and alcohol may also be simultaneously combined and catalyzed by addition of resin acid or other heterogeneous catalyst to produce the olefinated/esterified product.

Comparison of crude oil interfacial behavior

Energy Technology Data Exchange (ETDEWEB)

Beetge, J.H.; Panchev, N. [Champion Technologies Inc., Fresno, TX (United States)

2008-07-01

The bulk properties of crude oil are used to predict its behaviour with regards to treatment, transport and processing. Surface active components, such as asphaltenes, are often used to study or explain critical interfacial behaviour of crude oil. This study investigated the differences and similarities in the interfacial behaviour of the collective surface active component in various crude oils from different sources. The properties of interfaces between crude oil and water were compared using a Teclis drop shape tensiometer. A portion of a crude oil sample was diluted in toluene and contacted with water in a rising drop configuration. Dynamic surface tension and interfacial rheology was examined as a function of time from the early stages of interface formation. Sinusoidal oscillation of the drop volume allowed for the evaluation of visco-elastic behaviour of the crude oil/water interface as it developed with time. The Gibbs elastic modulus, as well as its elastic and viscose components were calculated from the drop shape. The interfacial behaviour was expressed in terms of concentration, oscillation frequency and interface age. It was concluded that knowledge of crude oil interfacial character could be of value in the treatment, transport and processing of crude oils because the its behaviour may play a significant role in crude oil production and processing.

Estimation of evaporative losses during storage of crude oil and petroleum products

Directory of Open Access Journals (Sweden)

Mihajlović Marina A.

2013-01-01

Full Text Available Storage of crude oil and petroleum products inevitably leads to evaporative losses. Those losses are important for the industrial plants mass balances, as well as for the environmental protection. In this paper, estimation of evaporative losses was performed using software program TANKS 409d which was developed by the Agency for Environmental Protection of the United States - US EPA. Emissions were estimated for the following types of storage tanks: fixed conical roof tank, fixed dome roof tank, external floating roof tank, internal floating roof tank and domed external floating roof tank. Obtained results show quantities of evaporated losses per tone of stored liquid. Crude oil fixed roof storage tank losses are cca 0.5 kg per tone of crude oil. For floating roof, crude oil losses are 0.001 kg/t. Fuel oil (diesel fuel and heating oil have the smallest evaporation losses, which are in order of magnitude 10-3 kg/tone. Liquids with higher Reid Vapour Pressure have very high evaporative losses for tanks with fixed roof, up to 2.07 kg/tone. In case of external floating roof tank, losses are 0.32 kg/tone. The smallest losses are for internal floating roof tank and domed external floating roof tank: 0.072 and 0.044, respectively. Finally, it can be concluded that the liquid with low volatility of low BTEX amount can be stored in tanks with fixed roof. In this case, the prevailing economic aspect, because the total amount of evaporative loss does not significantly affect the environment. On the other hand, storage of volatile derivatives with high levels of BTEX is not justified from the economic point of view or from the standpoint of the environment protection.

Design and implementation of a control structure for quality products in a crude oil atmospheric distillation column.

Science.gov (United States)

Sotelo, David; Favela-Contreras, Antonio; Sotelo, Carlos; Jiménez, Guillermo; Gallegos-Canales, Luis

2017-11-01

In recent years, interest for petrochemical processes has been increasing, especially in refinement area. However, the high variability in the dynamic characteristics present in the atmospheric distillation column poses a challenge to obtain quality products. To improve distillates quality in spite of the changes in the input crude oil composition, this paper details a new design of a control strategy in a conventional crude oil distillation plant defined using formal interaction analysis tools. The process dynamic and its control are simulated on Aspen HYSYS ® dynamic environment under real operating conditions. The simulation results are compared against a typical control strategy commonly used in crude oil atmospheric distillation columns. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Kurdistan crude oils as feedstock for production of aromatics

Directory of Open Access Journals (Sweden)

Abdulsalam R. Karim

2017-05-01

Full Text Available Crude oils from various locations in Iraqi Kurdistan were fully evaluated, so that enables refiners to improve their operation by selecting the best crude oil that yields high naphtha content to be used as a catalytic reforming feedstock after determination of total sulfur content and then de sulfurizing them, then cyclizing or reforming these sweet naphtha cuts to produce aromatic fractions which can be split into benzene, toluene, and xylenes.

Design and development of a high efficiency tank for crude oil dehydration (i)

International Nuclear Information System (INIS)

Forero, Jorge Enrique; Ortiz Olga Patricia; Narino, Fredy Abelardo

2008-01-01

This paper introduces a new tank design for dehydrating and desalting large volumes of crude oils previously degasified, crude oil dehydration efficiency is reduced by gas presence in the emulsion interphase. The design presented in this paper is versatile (it is adaptable to any classical dehydration process), highly efficient in terms of separation (values usually greater than 90% and/or treated crude oil BSW less than 0,5% are ensured), low installation and operation costs, less consumption of additives. These are some of the advantages found in pilot tests plants and proven in industrial systems at the ECOPETROL S.A. production fields with treatment capacities from 14 to 50 KBD. Although this process also can be applied to other ranks of flow, maintaining the design critical conditions of each case in particular. This system does not exhibit the typical limitations shown by treatment traditional systems (FWKO, Gun Barrel, thermal and electrostatic separators, etc.) (Al-Ghamdi, 2007) since it can be easily adapted to system treatments for light, intermediate, and heavy crude oils and to treatments with BSW content ranging from a very low levels of ≤ 1% to very high levels ≥ 95%, values that are not unusual in production fields nowadays, especially where accelerated production methods are used

CG/MS quantitation of diamondoid compounds in crude oils and petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.D.; Hollebone, B.P.; Fingas, M.; Peng, X.; Landriault, M.

2006-01-01

Diamondoids are a class of saturated hydrocarbons that consist of 3-dimensionally fused cyclohexane rings. Diamondoid compounds in petroleum are the result of carbonium ion rearrangements of cyclic precursors on clay superacids in the source rock during oil generation. They are considered to be a problem due to their deposition during production of reservoir fluids and transportation of natural gas, gas condensates and light crude oils. At high concentrations, and with changes in pressure and temperature, diamondoid compounds can segregate out of reservoir fluids during production. Environmental scientists have considered fingerprinting the diamondoid hydrocarbons as a forensic method for oil spill studies. Since diamondoid compounds are thermodynamically stable, they have potential applications in oil-source correlation and differentiation for cases where traditional biomarker terpanes and steranes are absent because of environmental weathering or refining of petroleum products. Although there is increased awareness of possible use of diamondoid compounds for source identification, there is no systematic approach for using these compounds. Quantitative surveys of the abundances of diamondoids are not available. Therefore, this study developed a reliable analytical method for quantitative diamondoid analysis. Gas chromatography/mass spectrometry (GC/MS) was used to quantitatively determine diamondoid compounds (adamantane, diamantane and their alkylated homologues) in 14 fresh crude oils and 23 refined petroleum products, including light and mid-range distillate fuels, residual fuels and lubricating oils collected from different sources. Results were compared with 2 types of biomarker compounds in oil saturated hydrocarbon fractions. Several diagnostic ratios of diamondoids were developed based on their concentrations. Their potential use for forensic oil spill source identification was evaluated. 24 refs., 8 tabs., 4 figs

Co-digestion of swine excreta associated with increasing levels of crude glycerin

Directory of Open Access Journals (Sweden)

Marco Antonio Previdelli Orrico Junior

2016-03-01

Full Text Available ABSTRACT The objective of this research was to evaluate the performance of anaerobic co-digestion of swine excreta associated with increasing doses of crude glycerin and different hydraulic retention times (HRT. A completely randomized design was adopted in a 3 × 4 factorial arrangement composed of three HRT (10, 17, and 24 days and four crude glycerin doses (0, 5, 10, and 15 g/100 g of total solids [TS], with four replications per treatment. The assessed parameters were: biogas production potential, reductions of volatile solids (VS, chemical oxygen demand (COD, and most probable number of total and thermotolerant coliforms. The biogas production per added VS presented quadratic effect at 17 and 24 days of HRT, with ideal doses of 5.5 and 5.9 g of crude glycerin/100 g TS, respectively. There was no difference among glycerin doses at 10-day HRT for VS reductions; however, at HRT of 17 and 24 days, there were differences, with greater reduction of 61.1% for 5 g of crude glycerin/100 g TS at 24-day HRT. The COD reduction values showed an effect among retention times, in which the 24-day HRT provided the best results. Reductions in coliforms were greater than 99%, with no difference among treatments. Addition of 5 to 6 g of crude glycerin/100 g TS with a 24-day HRT is more effective in biogas production and reduction of VS, COD, and coliforms from co-digestion of swine excreta.

Crude oil–corn–ethanol – nexus: A contextual approach

International Nuclear Information System (INIS)

Natanelov, Valeri; McKenzie, Andrew M.; Van Huylenbroeck, Guido

2013-01-01

This paper offers a holistic study on the complex relationships between crude oil, corn and ethanol during a turbulent period between 2006 and end of 2011. Through a holistic mapping of the current market situation and a contextual analytical design we show that there exists a strong relationship between crude oil and corn markets on one side, and crude oil and ethanol on the other. However, the price relationship between corn and ethanol was revealed to be less straightforward, and is driven by the US government fuel policy. Furthermore the study indicates that corn markets have became more prone to volatility due to ethanol production, especially when the demand for corn is high and/or the crude oil prices are high enough to create a competitive market for ethanol. - Highlights: • Strong relationship between crude oil–corn and crude oil–ethanol. • Corn–ethanol connected through a by-pass of crude oil markets. • Ethanol market has no direct impact on the price levels of corn. • Corn markets became more prone to volatility due to ethanol production

The Application of Neural Networks in Balancing Production of Crude Sunflower Oil and Meal

Directory of Open Access Journals (Sweden)

Bojan Ivetic

2014-08-01

Full Text Available The aim of the research is to predict specific output characteristics of half finished goods (crude sunflower oil and meal on the basis of specific input variables (quality and composition of sunflower seeds, with the help of artificial neural networks. This is an attempt to predict the amount much more precisely than is the case with technological calculations commonly used in the oil industry. All input variables are representing the data received by the laboratory, and the output variables except category % of oil which is obtained by measuring the physical quantity of produced crude sunflower oil and sunflower consumed quantity of the processing quality. The correct prediction of the output variables contributes to better sales planning, production of sunflower oil, and better use of storage. Also, the correct prediction of technological results of the quality of crude oil and meal provides timely response and also preventing getting rancid and poor-quality oil, timely categorizing meal, which leads to proper planning and sales to the rational utilization of storage space, allows timely response technologists and prevents the growth of microorganisms in the meal.

Indigenous production of biosurfactant and degradation of crude oil

Directory of Open Access Journals (Sweden)

Hamid Rashedi

2015-04-01

Full Text Available The present study investigated the isolation and identification of biosurfactant producing bacteria from Iranian oil wells. The biosurfactant production of bacteria isolates was evaluated and confirmed using hemolysis and emulsification tests. The biodegradation of crude oil was studied using GC and HPLC analysis. A total of 45 strains have been isolated. These strains showed less than a 40 mN m-1 reduction in surface tension. The effects of different pH (4.2-9.2, salinity concentrations (1%-15%, and temperatures (25-50 in biosurfactant production of isolated strains were evaluated. One of the strains (Bacillus sp. NO.4 showed a high salt tolerance and a successful production of biosurfactant in a vast pH range. Its maximum biomass production (about 3.1 g L-1 dry weight was achieved after 60 hours of growth. The surface tension of the culture broth dropped rapidly after inoculation and reached its lowest value (36 mN m-1 during the exponential phase after about 36-48 hours of growth. The study of the GC graphs showed that higher aliphatic reduction occurred in fractions with C14 to C24 hydrocarbons. The depicted results of the HPLC graphs indicated a 100% degradation of chrysene and fluorine. In this study, we demonstrated the useful capacities of the isolates in removing oil pollutants and their application in MEOR in vitro.

U.S. crude oil, natural gas, and natural gas liquids reserves 1997 annual report

Energy Technology Data Exchange (ETDEWEB)

Wood, John H.; Grape, Steven G.; Green, Rhonda S.

1998-12-01

This report presents estimates of proved reserves of crude oil, natural gas, and natural gas liquids as of December 31, 1997, as well as production volumes for the US and selected States and State subdivisions for the year 1997. Estimates are presented for the following four categories of natural gas: total gas (wet after lease separation), nonassociated gas and associated-dissolved gas (which are the two major types of wet natural gas), and total dry gas (wet gas adjusted for the removal of liquids at natural gas processing plants). In addition, reserve estimates for two types of natural gas liquids, lease condensate and natural gas plant liquids, are presented. Also included is information on indicated additional crude oil reserves and crude oil, natural gas, and lease condensate reserves in nonproducing reservoirs. A discussion of notable oil and gas exploration and development activities during 1997 is provided. 21 figs., 16 tabs.

Eastern Canadian crude oil supply and its implications for regional energy security

International Nuclear Information System (INIS)

Hughes, Larry

2010-01-01

Canada has been blessed with immense energy resources; however, their distribution is not uniform. One such example is crude oil, which is found primarily in western Canada. Eastern Canada, consisting of the six eastern-most provinces (Newfoundland and Labrador, New Brunswick, Nova Scotia, Ontario, Prince Edward Island, and Quebec), produce limited quantities of crude oil, most of which is exported to the United States. Ideally, western Canadian crude oil would meet the demands of eastern Canada; however, the North American Free Trade Agreement (NAFTA) and the absence of oil pipelines means that eastern Canada increasingly relies on supplies of crude oil from a small number of oil exporting countries, many with declining production. This paper examines crude oil production, supply, and its refining in eastern Canada. It shows that crude production in the region has reached its peak and that increasing global competition for crude oil will affect energy security in eastern Canada, either through price increases or supply shortages, or both. (author)

Effect of Addition of Moringa Leaf By-Product (Leaf-Waste) on ...

African Journals Online (AJOL)

The effects of incorporation of Moringa leaf fibre (a by-product of leaf processing which contains 24% Crude Fibre by dry weight at 0, 5 and 10 % substitution of wheat flour in cookies was investigated. Three products containing wheat flour: Moringa leaf fibre ratios of 100:0, 95:5, and 90:10 respectively were prepared, and a ...

EVALUATING THE SHORT RUN EFFECTS OF U.S. CRUDE OIL INVENTORY LEVELS ON WTI CRUDE OIL PRICE FROM 1993 - 2013

Directory of Open Access Journals (Sweden)

Tobi Olasojiand

2016-07-01

Full Text Available The focus of this research was to investigate the short-term influence of U.S. crude oil inventories on WTI crude oil prices from 1993 to 2013. This study is important for policy makers who wish to reduce the persistent and growing price volatility of crude oil and its related products as well as businesses such as airline companies who wish to make annual budgetary sales decisions. Using OLS multiple regression, cointegration, VECM and Ex-post forecast techniques; we provide evidence of an inelastic relationship in which a 1% increase in U.S. crude oil inventories is associated with 0.46% decrease in WTI crude oil prices; however this was only valid for 22% of WTI crude oil price variation. We also find that past data on U.S. crude oil inventories could be used to predict future WTI crude oil prices movement. Contrary to literature, the results of the VECM analysis indicate there is no short-run relationship between both variables over the trajectory.

EVALUATION OF CORROSION COST OF CRUDE OIL PROCESSING INDUSTRY

Directory of Open Access Journals (Sweden)

ADESANYA A.O.

2012-08-01

Full Text Available Crude oil production industry as the hub of Nigeria Economy is not immune to the global financial meltdown being experienced world over which have resulted in a continual fall of oil price. This has necessitated the need to reduce cost of production. One of the major costs of production is corrosion cost, hence, its evaluation. This research work outlined the basic principles of corrosion prevention, monitoring and inspection and attempted to describe ways in which these measures may be adopted in the context of oil production. A wide range of facilities are used in crude oil production making it difficult to evaluate precisely the extent of corrosion and its cost implication. In this study, cost of corrosion per barrel was determined and the annualized value of corrosion cost was also determined using the principles of engineering economy and results analyzed using descriptive statistics. The results showed that among the corrosion prevention methods identified, the use of chemical treatment gave the highest cost contribution (81% of the total cost of prevention while coating added 19%. Cleaning pigging and cathodic protection gave no cost. The contribution of corrosion maintenance methods are 60% for repairs and 40% for replacement. Also among the corrosion monitoring and inspection identified, NDT gave the highest cost contribution of 41% of the total cost, followed by coating survey (34%. Cathodic protection survey and crude analysis gives the lowest cost contribution of 19% and 6% respectively. Corrosion control cost per barrel was found to be 77 cent/barrel. The significance of this cost was not much due to high price of crude oil in the international market. But the effect of corrosion in crude oil processing takes its toll on crude oil production (i.e. deferment.

Production of lipase and protease from an indigenous Pseudomonas aeruginosa strain and their evaluation as detergent additives: compatibility study with detergent ingredients and washing performance.

Science.gov (United States)

Grbavčić, Sanja; Bezbradica, Dejan; Izrael-Živković, Lidija; Avramović, Nataša; Milosavić, Nenad; Karadžić, Ivanka; Knežević-Jugović, Zorica

2011-12-01

An indigenous Pseudomonas aeruginosa strain has been studied for lipase and protease activities for their potential application in detergents. Produced enzymes were investigated in order to assess their compatibility with several surfactants, oxidizing agents and commercial detergents. The crude lipase appeared to retain high activity and stability in the presence of several surfactants and oxidizing agents and it was insusceptible to proteolysis. Lutensol® XP80 and Triton® X-100 strongly activated the lipase for a long period (up to 40 and 30% against the control after 1h) while the protease activity was enhanced by the addition of Triton® WR1339 and Tween® 80. The washing performance of the investigated surfactants was significantly improved with the addition of the crude enzyme preparation. Studies were further undertaken to improve enzymes production. The optimization of fermentation conditions led to an 8-fold increase of lipase production, while the production of protease was enhanced by 60%. Copyright © 2011 Elsevier Ltd. All rights reserved.

Biosurfactant production by the crude oil degrading Stenotrophomonas sp. B-2: chemical characterization, biological activities and environmental applications.

Science.gov (United States)

Gargouri, Boutheina; Contreras, María Del Mar; Ammar, Sonda; Segura-Carretero, Antonio; Bouaziz, Mohamed

2017-02-01

In this work, biosurfactant-producing microorganisms were isolated from hydrocarbon-contaminated water collected from Tunisian oilfield. After enrichment and isolation, different bacterial strains were preliminary studied for their biosurfactant/bioemulsifier properties when using crude oil as the unique carbon source. In particular, the isolate strain B-2, a Gram-negative, rod-shaped bacterium, efficiently emulsified crude oil. The extracellular biosurfactant product from this strain presented an emulsification activity above 70% and a hydrophobicity of 71%. In addition, a diameter of 6 cm was observed in the oil displacement test. The characterization of B-2 strain using 16S rDNA sequencing enables us to find a high degree of similarity with various members of the genus Stenotrophomonas (with a percentage of similarity of 99%). The emulsification activity of Stenotrophomonas biosurfactant B-2 was maintained in a wide range of pH (2 to 6), temperature (4 to 55 °C), and salinity (0 to 50 g L -1 ) conditions. It also enhanced the solubility of phenanthrene in water and could be used in the re-mobilization of hydrocarbon-contaminated environment. In addition, this biosurfactant exhibited antimicrobial and antioxidant properties. Infrared spectroscopy suggested potential lipidic and peptidic moieties, and mass spectrometry-based analyses showed that the biosurfactant contains mainly cyclic peptidic structures belonging to the class of diketopiperazines. Therefore, the B-2 strain is a promising biosurfactant-producing microorganism and its derived biosurfactant presents a wide range of industrial applications.

Liquid ultrasonic flow meters for crude oil measurement

Energy Technology Data Exchange (ETDEWEB)

Kalivoda, Raymond J.; Lunde, Per

2005-07-01

Liquid ultrasonic flow meters (LUFMs) are gaining popularity for the accurate measurement of petroleum products. In North America the first edition of the API standard ''Measurement of liquid hydrocarbons by ultrasonic flow meters using transit time technology'' was issued in February 2005. It addresses both refined petroleum products and crude oil applications. Its field of application is mainly custody transfer applications but it does provide general guidelines for the installation and operation of LUFM's other applications such as allocation, check meters and leak detection. As with all new technologies performance claims are at times exaggerated or misunderstood and application knowledge is limited. Since ultrasonic meters have no moving parts they appear to have fewer limitations than other liquid flow meters. Liquids ultrasonic flow meters, like turbine meters, are sensitive to fluid properties. It is increasingly more difficult to apply on high viscosity products then on lighter hydrocarbon products. Therefore application data or experience on the measurement of refined or light crude oil may not necessarily be transferred to measuring medium to heavy crude oils. Before better and more quantitative knowledge is available on how LUFMs react on different fluids, the arguments advocating reduced need for in-situ proving and increased dependency on laboratory flow calibration (e.g. using water instead of hydrocarbons) may be questionable. The present paper explores the accurate measurement of crude oil with liquid ultrasonic meters. It defines the unique characteristics of the different API grades of crude oils and how they can affect the accuracy of the liquid ultrasonic measurement. Flow testing results using a new LUFM design are discussed. The paper is intended to provide increased insight into the potentials and limitations of crude oil measurement using ultrasonic flow meters. (author) (tk)

Crude oil prices : how high, how much harm?

International Nuclear Information System (INIS)

Levesque, M.; Alexander, C.

2002-01-01

This paper discussed the issue of crude oil prices and the economy. Crude oil prices are on the rise due to the recent events in the Middle East. In early April, West Texas Intermediate crude oil climbed to nearly US$28 a barrel. Most of the increase reflects the expectation of stronger world oil demand combined with supply constraints on the part of OPEC. Although there has been some concern expressed that rising oil prices may hinder economic recovery, the authors of this report do not see evidence that rising oil prices would throw economic recovery off course, arguing that the current spike will be short-lived. They stated that even under a worse-case scenario where prices remain inflated, there is little reason to fear for the health of the Canadian economy. OPEC is expected to increase its low production quotas in June. In addition, non-OPEC nations (Russia in particular) are expected to increase oil production in the coming months. The authors also indicated that it is unlikely that conflict in the West Bank will disrupt oil supply because Israel is not an oil-exporting nation. However, oil supply could be affected if other Arab nations were drawn into the issue. It was also noted that military action against Iraq would increase oil prices, possibly as high as US$40 a barrel, but the full extent of this hike in price will probably be unsustainable. In addition, the authors emphasized that the increase in energy costs would not be enough to seriously jeopardize the economic recovery in the United States. As for Canada, it is estimated that a US$10 per barrel increase in crude oil prices would have a small, but positive impact on Canadian GDP because in contrast to the United States, Canada produces much more energy than it consumers. In 2001, Canada ran a trade surplus of $2.8 billion. The report ended by stating that although higher oil prices could add a full percentage point to headline inflation by the end of the year, core inflation is likely to remain

Growth and carcass production responses of EPMp broiler ducks to various levels of crude fiber and protein in the diet

Directory of Open Access Journals (Sweden)

Maijon Purba

2014-10-01

Full Text Available Inclusion of crude fiber in diet is important for duck growth, but there is a limit in its use in order for the ducks to grow normally. The purpose of this study was to evaluate growth and carcass production responses of EPMp broiler ducks under different levels of crude fiber and protein in diets. Four hundreds and twenty day old ducklings were allocated into 7 treatments with 6 replications and each replication consisted of 10 ducks. The treatments were the factorial combinations of crude fiber content of 6 or 9% and protein content of 19, 21, or 23%; and BR-1 (starter diet as positive control. The variables observed were: feed intake, weekly body weight, and percentage of carcass production. The results showed that all variables observed were not significantly affected by CF content, but highly significantly affected by crude protein levels in diet. Protein content of 19 or 21% in diet resulted in a better performance for EPMp ducks. The inclusion of high CF in diet did not affect carcass percentage, except for reduced abdominal fat. The study implies that administration of high CF (6 or 9% with a protein content of 19 or 21% in the diet are still acceptable to EPMp ducks at 12 weeks.

Experimental, kinetic and numerical modeling of hydrogen production by catalytic reforming of crude ethanol over a commercial catalyst in packed bed tubular reactor and packed bed membrane reactor

International Nuclear Information System (INIS)

Aboudheir, Ahmed; Akande, Abayomi; Idem, Raphael

2006-01-01

The demand for hydrogen energy has increased tremendously in recent years essentially because of the increase in the word energy consumption as well as recent developments in fuel cell technologies. The energy information administration has projected that world energy consumption will increase by 59% over the next two decades, from 1999 to 2020, in which the largest share is still dominated by fossil fuels (oil, natural gas and coal). Carbon dioxide (CO 2 ) emissions resulting from the combustion of these fossil fuels currently are estimated to account for three-fourth of human-caused CO 2 emissions worldwide. Greenhouse gas emission, including CO 2 , should be limited, as recommended at the Kyoto Conference, Japan, in December 1997. In this regard, hydrogen (H 2 ) has a significant future potential as an alternative fuel that can solve the problems of CO 2 emissions as well as the emissions of other air contaminants. One of the techniques to produce hydrogen is by reforming of hydrocarbons or biomass. Crude ethanol (a form of biomass, which essentially is fermentation broth) is easy to produce, is free of sulphur, has low toxicity, and is also safe to handle, transport and store. In addition, crude ethanol consists of oxygenated hydrocarbons, such as ethanol, lactic acid, glycerol, and maltose. These oxygenated hydrocarbons can be reformed completely to H 2 and CO 2 , the latter of which could be separated from H 2 by membrane technology. This provides for CO 2 capture for eventual storage or destruction. In the case of using crude ethanol, this will result in negative CO 2 , emissions. In this paper, we conducted experimental work on production of hydrogen by the catalytic reforming of crude ethanol over a commercial promoted Ni-based catalyst in a packed bed tubular reactor as well as a packed bed membrane reactor. As well, a rigorous numerical model was developed to simulate this process in both the catalytic packed bed tubular reactor and packed bed membrane

Effects of selected thermophilic microorganisms on crude oils at elevated temperatures and pressures. Final report

Energy Technology Data Exchange (ETDEWEB)

Premuzic, E.T.; Lin, M.S.

1995-07-01

During the past several years, a considerable amount of work has been carried out showing that microbially enhanced oil recovery (MEOR) is promising and the resulting biotechnology may be deliverable. At the Brookhaven National Laboratory (BNL), systematic studies have been conducted which dealt with the effects of thermophilic and thermoadapted bacteria on the chemical and physical properties of selected types of crude oils at elevated temperatures and pressures. Particular attention was paid to heavy crude oils from Venezuela, California, Alabama, Arkansas, Wyoming, Alaska, and other oil producing areas. Current studies indicate that during the biotreatment several chemical and physical properties of crude oils are affected. The oils are (1) emulsified; (2) acidified; (3) there is a qualitative and quantitative change in light and heavy fractions of the crudes; (4) there are chemical changes in fractions containing sulfur compounds; (5) there is an apparent reduction in the concentration of trace metals; (6) the qualitative and quantitative changes appear to be microbial species dependent; and (7) there is a distinction between {open_quotes}biodegraded{close_quotes} and {open_quotes}biotreated{close_quotes} oils. Preliminary results indicate the introduced microorganisms may become the dominant species in the bioconversion of oils. These studies also indicate the biochemical interactions between crude oils and microorganisms follow distinct trends, characterized by a group of chemical markers. Core-flooding experiments have shown significant additional crude oil recoveries are achievable with thermophilic microorganisms at elevated temperatures similar to those found in oil reservoirs. In addition, the biochemical treatment of crude oils has technological applications in downstream processing of crude oils such as in upgrading of low grade oils and the production of hydrocarbon based detergents.

The Optimation of Crude Fiber Content of Diet for Fattening Madura Beef Cattle to Achieve Good A:P Ratio and Low Methane Production

Science.gov (United States)

Luthfi, N.; Restitrisnani, V.; Umar, M.

2018-02-01

Abtract. Methane (CH4) is one of the major greenhouse gases being reducted. This study was carried out to determine the optimum of crude fiber needed for fattening Madura beef cattle to achieve low methane production. Twenty-four male madura beef cattles with an average body weight of 206.89 ± 7.82 kg were used in this study. Cattle were fed contained 47.65 - 70.23 % Total Digestible Nutrients (TDN), 9.22 - 13.20% Crude Protein (CP), and 10.25 - 28.53% Crude Fiber (CF). Correlation analysis was used to describe the correlations among crude fiber,Methane, and Acetate:Propionate acid ratio. The result showed that crude fiber (%) had medium possitive correlation with methane and the equation was y = 0.0936x + 5.4853 with determination as much as 33.98%. The Acetate: propionate acid had positive correlation withmethane and the equation was y = 1.1121x + 3.581 with determination as much as 61.64%. Crude fiber (%) had low possitive correlation with A/P ratio and the equation was y = 0.039x + 2.4437 with determination as much as 9.56%. According to the results, it can be concluded that the optimum ofcrude fiberof diet for Madura beef cattle should be 15.38% to obtain A:P ratio of 3 or less and methane production of 6.91 MJ/d.

Biodegradation of Alaska North Slope crude oil enhanced by commercial bioremediation agents

International Nuclear Information System (INIS)

Aldrett, S.; Bonner, J.S.; Mills, M.A.; McDonald, T.J.; Autenrieth, R.L.

1996-01-01

The biodegradation of crude oil was studied. Tests were conducted in which natural unpolluted seawater was collected and then contaminated with Alaska North Slope crude oil. The oil was weathered by heating it to 521 degrees F to remove the light-end hydrocarbons. A total of 13 different bioremediation agents were tested, each one separately. Three samples per treatment were destructively analysed for petroleum chemistry. The thirteen treatments were analyzed for oil and grease. It was found that microbial degradation of petroleum hydrocarbons was enhanced by the addition of bioremediation agents, but it was not possible to identify the intermediate products responsible for the increase of resolved petroleum hydrocarbons through time. It was suggested that caution be used when interpreting results since the protocols used to test the products were prone to uncontrollable variations. 11 refs., 5 tabs., 6 figs

Effect of Sludge Concentration and Crude Glycerol Matrix as a Substrate on the Production of Single-Cell Oil by Oleaginous Yeast Yarrowia lipolytica SKY7

Directory of Open Access Journals (Sweden)

Saurabh Kumar Ram

2018-04-01

Full Text Available The disposal of excess crude glycerol produced by the booming biodiesel industry and wastewater sludge solid waste has become a severe problem, and alternate routes of use and valorization of these waste byproducts are needed. The use of cheaply available wastewater sludge solids in fermentation media is very much desirable to reduce the cost of production. The strains of Yarrowia lipolytica can assimilate a wide array of waste substrates, such as crude glycerol, waste cooking oil, starch wastewater, and cellulosic. This study optimized the concentration of wastewater sludge solids (5–35 g/L to be used with crude glycerol in fermentation media to produce microbial oil as feedstock for biodiesel production. The results indicated that 20 g/L of sludge solids with 40 g/L of crude glycerol resulted in highest lipid content of 29.35% in 96 h. Further, assuming wet extraction of lipids, it was found that at least 11.2% or higher lipid content is required for this process to have an overall positive net solid waste reduction. Insignificant inhibition was observed by the crude glycerol used in this study as compared to pure glycerol, which proves it to be an adequate source of carbon substrate for lipid production.

Canadian heavy crude oil and bitumen: Some new and old ideas

International Nuclear Information System (INIS)

Scott, G.R.

1992-01-01

Canadian conventional heavy oil and bitumen production has been steadily increasing over the last five years. This rise is forecast to continue under modest future crude oil pricing assumptions. During 1990 and 1991, the heavy oil market suffered from wide pricing differentials relative to light crude due to market reductions in Montreal and a feedstock shift at Uno-Ven's Chicago refinery, as well as an increase in the percentage of heavy in the world crude oil supply because of the Iraqi war. These have been offset by price-related bitumen production cuts and minor refinery capacity growth at other locations. The industry is poised for positive change with modest but stable prices and reduced light-heavy differentials caused, in part, by anticipated market expansion due to the June start-up of the Conco coker (50,000 bbl/d) in Montana and the anticipated late fall start up of the Bi-Provincial Upgrader in Saskatchewan (50,000 bbl/d blend). For the future, refinery upgrading and new grass roots refinery additions are suggested for western Canada. Associated transportation savings and condensate blending stock costs are two areas of advantage. Taken together with environmental problems in other densely populated market areas, it makes sense to build new heavy processing capacity near Edmonton but only after all current capacity is debottlenecked and inexpensive additions to current facilities are completed. New capacity will only be built when the heavy/light price differential on feed stock provides economic justification. 11 refs., 2 tabs

Lifting the US crude oil export ban: A numerical partial equilibrium analysis

International Nuclear Information System (INIS)

Langer, Lissy; Huppmann, Daniel; Holz, Franziska

2016-01-01

The upheaval in global crude oil markets and the boom in shale oil production in North America brought scrutiny on the US export ban for crude oil from 1975. The ban was eventually lifted in early 2016. This paper examines the shifts of global trade flows and strategic refinery investments in a spatial, game-theoretic partial equilibrium model. We consider detailed oil supply chain infrastructure with multiple crude oil types, distinct oil products, as well as specific refinery configurations and modes of transport. Prices, quantities produced and consumed, as well as infrastructure and refining capacity investments are endogenous to the model. We compare two scenarios: an insulated US crude oil market, and a counter-factual with lifted export restrictions. We find a significant expansion of US sweet crude exports with the lift of the export ban. In the US refinery sector, more (imported) heavy sour crude is transformed. Countries importing US sweet crude gain from higher product output, while avoiding costly refinery investments. Producers of heavy sour crude (e.g. the Middle East) are incentivised to climb up the value chain to defend their market share and maintain their dominant position. - Highlights: • We study the impacts of lifting the US crude ban on global oil flows and investments. • We find massive expansion of US sweet crude oil exports. • We analyze the resulting welfare effects for US producers, refiners and consumers. • We indicate the changes on global trade patterns. • We conclude that lifting the ban is the right policy for the US and the global economy.

Maximising profitability through the use of simulation for new market crudes evaluation

Energy Technology Data Exchange (ETDEWEB)

Mendez, Maryro P. [KBC Advanced Technologies, Surrey (United Kingdom)

2012-07-01

There is nothing that contributes more to the cost of production for a refinery than the cost of crude oil and other feedstocks. The efficient and effective evaluation and selection of crude oil to a refinery will have a very significant impact on its profitability. The crude oil selected will impact the utilization and output from different process units, has the potential to impact maintenance and energy costs, and will impact product properties from the refinery. The tools and knowledge necessary for a good new crude evaluation program are addressed as part of this paper. The work process is outlined in detail. Finally, we address some of the risk management issues inherent in processing high margin crudes. Innovative simulation tools like Petro-SIM offer the platform to evaluate opportunities to capture the value that the sour/sweet crude differential and that the new crudes coming in to the market have to offer for a given refinery configuration. The paper provides comments on how KBC's methodology has helped refiners to check their ability to run new challenging crudes. (author)

Gas Production Generated from Crude Oil Biodegradation: Preliminary Study on its Aplication in Microbial Enhanced Oil Recovery (MEOR

Directory of Open Access Journals (Sweden)

Astri Nugroho

2009-11-01

Full Text Available Gas Production Generated from Crude Oil Biodegradation: Preliminary Study on its Aplication in MicrobialEnhanced Oil Recovery (MEOR. The objective of this study is to observe the capacity of gas production generatedfrom crude oil degradation by the isolated bacteria. The gas in the MEOR could increase pressure in the reservoir,decrease oil viscosity, increase oil permeability-due to the increase of the porosity and viscosity, and also increase oilvolume due to the amount of dissolved gas. A research on gas analysis of oil degradation by 6 isolated bacteria has beenconducted. The bacteria isolates including Bacillus badius (A, Bacillus circulans (B, Bacillus coagulans (C, Bacillusfirmus (D, Pasteurella avium (E and Streptobacillus moniliformis (F. The trial on gas production, gas analysis and oildegradation analysis, was carried out by using SMSS medium. The test of gas production was done by usingmicrorespirometer at 40°C. The result shows that B, C, D, E produce more gas than A and F. Gas of CO2, O2, CO, N2,CH4, and H2 were analyzed by using GC. The results show that only three gases were detected by GC i.e. CO2, N2, andO2. The concentration of CO2 and N2 gas increased while the concentration of O2 decreased over an 8th day ofobservation. CO2 gas producted by mix culture was higher than by the pure culture. On the 8th day of incubation, theproduction of CO2 gas by mix culture was 4,0452% while pure culture C and D only produced 2,4543% and 2,8729%.The mix culture increase simple hydrocarbon by 12.03% and the formation of a complex hydrocarbon by 3.07%. Themix culture (C-D generated the highest concentration of CO2 gas as well as a synergistic concortium that has ability todegrade crude oil.

Impact of Expanded North Slope of Alaska Crude Oil Production on Oil Flows in the Contiguous United States (Summary)

Energy Technology Data Exchange (ETDEWEB)

DeRosa, Sean e. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Flanagan, Tatiana Paz [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

Crude oil produced on the North Slope of Alaska (NSA) is primarily transported on the Trans-Alaska Pipeline System (TAPS) to in-state refineries and the Valdez Marine Terminal in southern Alaska. From the Terminal, crude oil is loaded onto tankers and is transported to export markets or to three major locations along the U.S. West Coast: Anacortes-Ferndale area (Washington), San Francisco Bay area, and Los Angeles area. North Slope of Alaska production has decreased about 75% since the 1980s, which has reduced utilization of TAPS.

Identification of crude-oil components and microorganisms that cause souring under anaerobic conditions.

Science.gov (United States)

Hasegawa, R; Toyama, K; Miyanaga, K; Tanji, Y

2014-02-01

Oil souring has important implications with respect to energy resources. Understanding the physiology of the microorganisms that play a role and the biological mechanisms are both important for the maintenance of infrastructure and mitigation of corrosion processes. The objective of this study was to identify crude-oil components and microorganisms in oil-field water that contribute to crude-oil souring. To identify the crude-oil components and microorganisms that are responsible for anaerobic souring in oil reservoirs, biological conversion of crude-oil components under anaerobic conditions was investigated. Microorganisms in oil field water in Akita, Japan degraded alkanes and aromatics to volatile fatty acids (VFAs) under anaerobic conditions, and fermenting bacteria such as Fusibacter sp. were involved in VFA production. Aromatics such as toluene and ethylbenzene were degraded by sulfate-reducing bacteria (Desulfotignum sp.) via the fumarate-addition pathway and not only degradation of VFA but also degradation of aromatics by sulfate-reducing bacteria was the cause of souring. Naphthenic acid and 2,4-xylenol were not converted.

EFFECTS OF PROTEIN-XANTHOPHYLL (PX CONCENTRATE OF ALFALFA ADDITIVE TO CRUDE PROTEIN-REDUCED DIETS ON NITROGEN EXCRETION, GROWTH PERFORMANCE AND MEAT QUALITY OF PIGS

Directory of Open Access Journals (Sweden)

Eugeniusz GRELA

2009-06-01

Full Text Available The infl uence of protein-xanthophyll (PX concentrate of alfalfa supplement to crude protein-reduced diets was examined in relation to nitrogen excretion, performance parameters and pig meat quality. The investigations included 60 growers (PL x PLW x Duroc crossbreeds assigned to 3 groups. The conclusion is that there is a large potential to decrease nitrogen emission to the environment by 10% lowering of dietary crude protein intake along with reduced animal growth rate and elevated mixture utilization. Inclusion of a protein-xanthophyll concentrate (PX of alfalfa to the diet is likely to diminish disadvantageous productive parameters arising from limiting of total crude protein level in relation to the requirements of pigs feeding norms [1993]. At the same time, it improves feed nitrogen utilization and reduces noxious odour emissions from a piggery. The components of a protein-xanthophyll concentrate (PX contribute to increased liver and kidney weight.

Dispersed catalysts for transforming extra heavy crude oil into transportable upgraded crude: phase identification

Energy Technology Data Exchange (ETDEWEB)

Martinez, S.; Canizales, E.; Machin, I. [Gerencia Depttal de Investigacion Estrategica en Refinacion PDVSA Intevep (Venezuela); Segovia, X.; Rivas, A.; Lopez, E.; Pena, J.P.; Rojas, J.D.; Sardella, R. [Gerencia Depttal de Infraestructura y Mejoramiento en Faja Petrolifera PDVSA Intevep (Venezuela)

2011-07-01

A new technology to convert extra heavy crude oil into transportable upgraded crude has been developed. A water/oil emulsion composed of steam and catalyst precursors is introduced in the feed which then generates unsupported dispersed catalyst in situ under thermal decomposition. The aim of this paper is to characterize the particles. The study was conducted in a laboratory and on a pilot scale on three different vacuum residues using high resolution transmission electron microscopy and a transmission electron microscope. Results showed that the particles were formed by oxides and inorganic sulphur based in transition metals and their sizes ranged between 5 and 120 nm; in addition, good dispersion was observed. This study demonstrated that the process involved in the generation of dispersed catalyst is extremely complex and showed that further work with heavy crude oils and its residua is required to understand the mechanisms involved.

Efficient way of importing crude oil from oil producing countries - A review on diversification policy of crude oil import

Energy Technology Data Exchange (ETDEWEB)

Lee, Dal Sok [Korea Energy Economics Institute, Euiwang (Korea)

1999-03-01

Since the second oil crisis, the government has operated the import diversification support program to reduce the risk of crude oil import from Middle-East region and to raise the ability of dealing with the risk. This study tried to seek policy trends in future through reviewing the market environment related to the crude oil import diversification policy and the goal, instrument and effect of the policy. The supply and demand of crude oil and the price are influenced by market system in the world oil market and there are various types of crude oil trading available to both sellers and buyers. There is a probability that the suspension of supply in a certain area could be led to the price issue rather than the physical use of crude oil. In addition, the advantage of price with long-term contract of crude oil was abolished since the price of crude oil imported by term contract has been linked to spot prices. As a result, it is shown that the potential benefit from crude oil import diversification policy is reduced although political and social insecurity still exists in Middle-East region. Therefore, it is desirable to maintain the existing support program until the amount of stored oil reaches the optimum level and to help private enterprises determine the import considering economical efficiency and risk. (author). 36 refs., 5 figs., 23 tabs.

Recent advances in the production of value added chemicals and lipids utilizing biodiesel industry generated crude glycerol as a substrate - Metabolic aspects, challenges and possibilities: An overview.

Science.gov (United States)

Vivek, Narisetty; Sindhu, Raveendran; Madhavan, Aravind; Anju, Alphonsa Jose; Castro, Eulogio; Faraco, Vincenza; Pandey, Ashok; Binod, Parameswaran

2017-09-01

One of the major ecological concerns associated with biodiesel production is the generation of waste/crude glycerol during the trans-esterification process. Purification of this crude glycerol is not economically viable. In this context, the development of an efficient and economically viable strategy would be biotransformation reactions converting the biodiesel derived crude glycerol into value added chemicals. Hence the process ensures the sustainability and waste management in biodiesel industry, paving a path to integrated biorefineries. This review addresses a waste to wealth approach for utilization of crude glycerol in the production of value added chemicals, current trends, challenges, future perspectives, metabolic approaches and the genetic tools developed for the improved synthesis over wild type microorganisms were described. Copyright © 2017 Elsevier Ltd. All rights reserved.

US crude oil, natural gas, and natural gas liquids reserves 1996 annual report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The EIA annual reserves report series is the only source of comprehensive domestic proved reserves estimates. This publication is used by the Congress, Federal and State agencies, industry, and other interested parties to obtain accurate estimates of the Nation`s proved reserves of crude oil, natural gas, and natural gas liquids. These data are essential to the development, implementation, and evaluation of energy policy and legislation. This report presents estimates of proved reserves of crude oil, natural gas, and natural gas liquids as of December 31, 1996, as well as production volumes for the US and selected States and State subdivisions for the year 1996. Estimates are presented for the following four categories of natural gas: total gas (wet after lease separation), nonassociated gas and associated-dissolved gas (which are the two major types of wet natural gas), and total dry gas (wet gas adjusted for the removal of liquids at natural gas processing plants). In addition, reserve estimates for two types of natural gas liquids, lease condensate and natural gas plant liquids, are presented. Also included is information on indicated additional crude oil reserves and crude oil, natural gas, and lease condensate reserves in nonproducing reservoirs. A discussion of notable oil and gas exploration and development activities during 1996 is provided. 21 figs., 16 tabs.

High-yield production of biodiesel by non-catalytic supercritical methanol transesterification of crude castor oil (Ricinus communis)

International Nuclear Information System (INIS)

Román-Figueroa, Celián; Olivares-Carrillo, Pilar; Paneque, Manuel; Palacios-Nereo, Francisco Javier; Quesada-Medina, Joaquín

2016-01-01

The synthesis of biodiesel from crude castor oil in a catalyst-free process using supercritical methanol in a batch reactor was investigated, studying the evolution of intermediate products as well as the conversion of triglycerides and the yield of FAMEs (fatty acid methyl esters) (biodiesel). Experiments were carried out in a temperature range of 250–350 °C (10–43 MPa) at reaction times of 15–90 min for a methanol-to-oil molar ratio of 43:1. Maintaining thermal stability of biodiesel is one of the most important concerns in high-yield supercritical biodiesel production. Hence, thermal decomposition degree of FAMEs was also investigated in different reaction conditions. The maximum yield of FAMEs (96.5%) was obtained at 300 °C (21 MPa) and 90 min. Under these conditions, the conversion of triglycerides was complete, the yield of intermediate products was low (3.29 and 1.41% for monoglycerides and diglycerides, respectively), and thermal decomposition of FAMEs did not occur. The maximum degree of thermal decomposition (80.9%) was produced at 350 °C (43 MPa) and 90 min. Methyl ricinoleate, whose fatty acid chain was the most abundant (88.09 mol%) in castor oil, was very unstable above 300 °C and 60 min, leading to low yields of FAMEs under these conditions. - Highlights: • Supercritical synthesis of biodiesel from crude castor oil was investigated. • Supercritical methanolysis of crude castor oil reached a high yield of FAMEs. • Ricinoleic acid methyl ester was very unstable above 300 °C and 60 min reaction.

Micro-aerobic, anaerobic and two-stage condition for ethanol production by Enterobacter aerogenes from biodiesel-derived crude glycerol

DEFF Research Database (Denmark)

Saisaard, Kanokrat; Angelidaki, Irini; Prasertsan, Poonsuk

2011-01-01

The microbial production of ethanol from biodiesel-derived crude glycerol by Enterobacter aerogenes TISTR1468, under micro-aerobic and anaerobic conditions, was investigated. The experimental results showed that micro-aerobic conditions were more favorable for cellular growth (4.0 g/L DCW), ethanol...

Additives in yoghurt production

Directory of Open Access Journals (Sweden)

Milna Tudor

2008-02-01

Full Text Available In yoghurt production, mainly because of sensory characteristics, different types of additives are used. Each group, and also each substance from the same group has different characteristics and properties. For that reason, for improvement of yoghurt sensory characteristics apart from addition selection, the quantity of the additive is very important. The same substance added in optimal amount improves yoghurt sensory attributes, but too small or too big addition can reduce yoghurt sensory attributes. In this paper, characteristics and properties of mostly used additives in yoghurt production are described; skimmed milk powder, whey powder, concentrated whey powder, sugars and artificial sweeteners, fruits, stabilizers, casein powder, inulin and vitamins. Also the impact of each additive on sensory and physical properties of yoghurt, syneresis and viscosity, are described, depending on used amount added in yoghurt production.

Modelling demand for crude oil products in Spain

International Nuclear Information System (INIS)

Pedregal, D.J.; Dejuan, O.; Gomez, N.; Tobarra, M.A.

2009-01-01

This paper develops an econometric model for the five most important crude oil products demand in Spain. The aim is the estimation of a range of elasticities of such demands that would serve as the basis for an applied general equilibrium model used for forecasting energy demand in a broader framework. The main distinctive features of the system with respect to previous literature are (1) it takes advantage of monthly information coming from very different information sources and (2) multivariate unobserved components (UC) models are implemented allowing for a separate analysis of long- and short-run relations. UC models decompose time series into a number of unobserved though economic meaningful components mainly trend, seasonal and irregular. A module is added to such structure to take into account the influence of exogenous variables necessary to compute price, cross and income elasticities. Since all models implemented are multivariate in nature, the demand components are allowed to interact among them through the system noises (similar to a seemingly unrelated equations model). The results show unambiguously that the main factor driving demand is real income with prices having little impact on energy consumption. (author)

Modelling demand for crude oil products in Spain

Energy Technology Data Exchange (ETDEWEB)

Pedregal, D.J. [Escuela Tecnica Superior de Ingenieros Industriales and Instituto de Matematica Aplicada a la Ciencia y la Ingenieria (IMACI), Universidad de Castilla-La Mancha (UCLM), Avenida Camilo Jose Cela s/n, 13071 Ciudad Real (Spain); Dejuan, O.; Gomez, N.; Tobarra, M.A. [Facultad de Ciencias Economicas y Empresariales, Universidad de Castilla-La Mancha (UCLM) (Spain)

2009-11-15

This paper develops an econometric model for the five most important crude oil products demand in Spain. The aim is the estimation of a range of elasticities of such demands that would serve as the basis for an applied general equilibrium model used for forecasting energy demand in a broader framework. The main distinctive features of the system with respect to previous literature are (1) it takes advantage of monthly information coming from very different information sources and (2) multivariate unobserved components (UC) models are implemented allowing for a separate analysis of long- and short-run relations. UC models decompose time series into a number of unobserved though economic meaningful components mainly trend, seasonal and irregular. A module is added to such structure to take into account the influence of exogenous variables necessary to compute price, cross and income elasticities. Since all models implemented are multivariate in nature, the demand components are allowed to interact among them through the system noises (similar to a seemingly unrelated equations model). The results show unambiguously that the main factor driving demand is real income with prices having little impact on energy consumption. (author)

Lactic acid fermentation of crude sorghum extract

Energy Technology Data Exchange (ETDEWEB)

Samuel, W.A.; Lee, Y.Y.; Anthony, W.B.

1980-04-01

Crude extract from sweet sorghum supplemented with vetch juice was utilized as the carbohydrate source for fermentative production of lactic acid. Fermentation of media containing 7% (w/v) total sugar was completed in 60-80 hours by Lactobacillus plantarum, product yield averaging 85%. Maximum acid production rates were dependent on pH, initial substrate distribution, and concentration, the rates varying from 2 to 5 g/liter per hour. Under limited medium supplementation the lactic acid yield was lowered to 67%. The fermented ammoniated product contained over eight times as much equivalent crude protein (N x 6.25) as the original medium. Unstructured kinetic models were developed for cell growth, lactic acid formation, and substrate consumption in batch fermentation. With the provision of experimentally determined kinetic parameters, the proposed models accurately described the fermentation process. 15 references.

Expanding U.S. markets for Canadian crude oil

International Nuclear Information System (INIS)

Heath, M.; Angevine, G.; Chan, K.; Renne, G.; Stariha, J.; MacKay, E.

1993-01-01

The quantities and types of Canadian, U.S. and competing foreign crudes flowing into U.S. market regions and the potential to retain and/or expand Canadian crude oil sales in each of those markets, was studied. The various pipeline system expansion/construction proposals were reviewed. Findings of the study with respect to prospects for crude oil sales into each of the U.S. market regions were presented. Opportunities and constraints with regard to the potential for incremental crude oil sales into each of the U.S. market regions were detailed. The study concluded that there was a substantial market in the U.S. for incremental sales of Canadian crudes. Most of the refineries in the U.S. market regions were more flexible in terms of their crude diet than they were before the rationalization and restructuring of the industry began. The market for crude oil in the U.S. was shown to be one of the most competitive in the world and the most volatile. The study also revealed that there were risks associated with large additions to the capacity to ship crude oil by pipeline from Western Canada, given the uncertainties surrounding future supply. 4 refs., figs., tabs

Heavy crude and tar sands - the long-term oil reserve

Energy Technology Data Exchange (ETDEWEB)

Barnea, J

1984-10-01

It appears that heavy crude and tar sands occur in many sedimentary areas, and estimates of known world-wide quantities exceed those known for conventional light crude resources. Although there are not precise figures available, production could be as high as three million barrels per day, with Venezuela, the US, and Canada the largest producers. There are different scales to measure the costs of production because of differences in the quality of various types of heavy crude and tar sands. Economic development of these resources should banish fears of oil scarcity in the foreseeable future. A center for information exchange through international meetings and publications is under development.

Profiling of Indigenous Microbial Community Dynamics and Metabolic Activity During Enrichment in Molasses-Supplemented Crude Oil-Brine Mixtures for Improved Understanding of Microbial Enhanced Oil Recovery

DEFF Research Database (Denmark)

Halim, Amalia Yunita; Pedersen, Dorthe Skou; Nielsen, Sidsel Marie

2015-01-01

Anaerobic incubations using crude oil and brine from a North Sea reservoir were conducted to gain increased understanding of indigenous microbial community development, metabolite production, and the effects on the oil–brine system after addition of a complex carbon source, molasses, with or with...... of molasses has potential as microbial enhanced oil recovery (MEOR) strategy in North Sea oil reservoirs.......Anaerobic incubations using crude oil and brine from a North Sea reservoir were conducted to gain increased understanding of indigenous microbial community development, metabolite production, and the effects on the oil–brine system after addition of a complex carbon source, molasses....... The microbial growth caused changes in the crude oil–brine system: formation of oil emulsions, and reduction of interfacial tension (IFT). Reduction in IFT was associated with microbes being present at the oil–brine interphase. These findings suggest that stimulation of indigenous microbial growth by addition...

Workshop Papers: Directions and Marketing of Synthetic Crude Oil and Heavy Oil

International Nuclear Information System (INIS)

1997-01-01

This workshop was organized by the National Centre for Upgrading Technology in an effort to bring together experts from the various sectors of the petroleum industry to outline their views of the directions that the synthetic crude oil market will pursue over the next decade and into the 21. century. The motivation for the Workshop came from the many announcements during 1996 and 1997 by several Canadian oil companies about plans to initiate or expand their heavy oil and synthetic crude production. During the same period, at least one US refiner also announced plans to revamp an existing refinery to allow it to process Canadian heavy oil and synthetic crude. The workshop was organized to review these plans and to discuss such questions as (1) Would the selected technologies be the familiar carbon rejection or hydrogen addition methods, or would there be radical advanced technologies? (2) Would the products be fully or partially upgraded? (3) How would they be processed in the refinery? (4) Would there be a market? This collection of papers or viewgraphs comprise all the formal presentations given at the workshop. The final section also contains the edited notes recorded during the question and answer periods. refs., tabs., figs

Green and sustainable succinic acid production from crude glycerol by engineered Yarrowia lipolytica via agricultural residue based in situ fibrous bed bioreactor.

Science.gov (United States)

Li, Chong; Gao, Shi; Yang, Xiaofeng; Lin, Carol Sze Ki

2018-02-01

In situ fibrous bed bioreactor (isFBB) for efficient succinic acid (SA) production by Yarrowia lipolytica was firstly developed in our former study. In this study, agricultural residues including wheat straw, corn stalk and sugarcane bagasse were investigated for the improvement of isFBB, and sugarcane bagasse was demonstrated to be the best immobilization material. With crude glycerol as the sole carbon source, optimization for isFBB batch fermentation was carried out. Under the optimal conditions of 20g sugarcane bagasse as immobilization material, 120gL -1 crude glycerol as carbon source and 4Lmin -1 of aeration rate, the resultant SA concentration was 53.6gL -1 with an average productivity of 1.45gL -1 h -1 and a SA yield of 0.45gg -1 . By feeding crude glycerol, SA titer up to 209.7gL -1 was obtained from fed batch fermentation, which was the highest value that ever reported. Copyright © 2017 Elsevier Ltd. All rights reserved.

World market of crude oil - review of possible scenarios of forecasting for the crude oil price movement

International Nuclear Information System (INIS)

Janevski, Risto

2003-01-01

Throughout most of 2002, crude oil prices were solidly within the range preferred by producers in the Organization of Petroleum Exporting Countries (OPEC), $22 to $28 per barrel for the OPEC 'basket price' (Fig. 1). OPEC producers have been demonstrating disciplined adherence to announced cutbacks in production. Early in 2003, a dramatic upward turn in crude oil prices was brought about by a combination of two factors. First, a general strike against the Chavez regime resulted in a sudden drop in Venezuela's oil exports. Although other OPEC producers agreed to increase production to make up for the lost Venezuelan output, the obvious strain on worldwide spare capacity kept prices high. Second, price volatility was exacerbated by fears of war in Iraq. (Original)

OPEC's optimal crude oil price

International Nuclear Information System (INIS)

Horn, Manfred

2004-01-01

OPEC decided to stabilise oil prices within a range of 22-28 US Dollar/barrel of crude oil. Such an oil-price-level is far beyond the short and long run marginal costs of oil production, beyond even that in regions with particularly high costs. Nevertheless, OPEC may achieve its goal if world demand for oil increases substantially in the future and oil resources outside the OPEC are not big enough to accordingly increase production. In this case OPEC, which controls about 78% of world oil reserves, has to supply a large share of that demand increase. If we assume OPEC will behave as a partial monopolist on the oil market, which takes into consideration the reaction of the other producers to its own sales strategy, it can reach its price target. Lower prices before 2020 are probable only if the OPEC cartel breaks up. Higher prices are possible if production outside OPEC is inelastic as assumed by some geologists, but they would probably stimulate the production of unconventional oil based on oil sand or coal. Crude oil prices above 30 US Dollar/barrel are therefore probably not sustainable for a long period. (Author)

Acid esterification of a high free fatty acid crude palm oil and crude rubber seed oil blend: Optimization and parametric analysis

Energy Technology Data Exchange (ETDEWEB)

Khan, Modhar A.; Yusup, Suzana; Ahmad, Murni M. [Universiti Teknologi PETRONAS, Chemical Engineering, Bandar Seri Iskandar, 31750 Tronoh, Perak (Malaysia)

2010-12-15

Free fatty acids content plays an important role in selecting the appropriate route for biodiesel production. Oils with high content of free fatty acids can be treated by acid esterification where an alcohol reacts with the given oil in the presence of acid catalyst. In the current study, an equivolume blend of crude rubber seed oil and crude palm oil is fed to the reaction with methanol as the alcohol of choice and sulfuric acid. Selected reaction parameters were optimized, using Taguchi method for design of experiments, to yield the lowest free fatty acid content in the final product. The investigated parameters include alcohol to oil ratio, temperature and amount of catalyst. The effect and significance of each parameter were then studied based on the fractional factorial design and verified by additional experiments. The optimum conditions for acid esterification which could reduce the free fatty acid content in the feedstock to lower than 0.6% (95% reduction) were 65 C, 15:1 methanol to oil ratio (by mole) and 0.5 wt% H{sub 2}SO{sub 4} after 3 h of reaction time. Temperature had been found to have the most effect on the reduction of free fatty acids followed by reactants ratio while increasing catalyst amount had nominal effect. (author)

Shell Scotsford's experience with a 100 per cent synthetic crude diet

International Nuclear Information System (INIS)

Margerum, M.

1997-01-01

A qualitative overview of Shell Canada's Scotford refinery was presented. The Scotford refinery is the only refinery in North America designed to run on 100 per cent synthetic crude. As a result, Scotford has a unique configuration and has faced some unique problems. Some of the challenges met in converting synthetic crude to today's products are described. The refinery's unique configuration is centered around a large hydrocracker and has high yield flexibility. The major units of the refinery are the crude unit, hydrocracker, naphtha hydrotreater and reformer, the aromatics complex, the distillate hydrogenator and the hydrogen plants. The refinery products include low sulphur gasoline, jet fuel and diesel fuel. Other products include LPG, FCC feed, benzene and solvents. Several process problems have been experienced at the Scotford refinery including hydrodenitrification of synthetic gasoline, PCA fouling, particulate fouling, crude unit fouling, and distillate lubricity. Solutions have been devised for most of these problems. 3 figs

High-fiber diets with reduced crude protein for commercial layers

Directory of Open Access Journals (Sweden)

MFFM Praes

2014-06-01

Full Text Available This study aimed at evaluating diets containing different fiber sources and two crude protein levels on the performance, egg quality, and nitrogen metabolism of commercial layers. In total, 392 48-wk-old Isa Brown layers were distributed according to a completely randomized experimental design in a 3x2+1 (control factorial arrangement, resulting in seven treatments with seven replicates of eight birds each. Treatments consisted of three fiber feedstuffs (cottonseed hulls, soybean hulls, and rice hulls and two dietary crude protein levels (12% and 16%. Cottonseed hulls associated with the high crude protein level (16% resulted in the worst feed conversion ratio per dozen eggs. Diets with 16% crude protein resulted in the highest feed intake, egg production, egg weight, egg mass values, and improved feed conversion ratio (kg eggs/kg feed. The dietary inclusion of soybean hulls determined low yolk pigmentation, and of rice hulls, low egg specific gravity. The 16% crude protein diet with rice hulls promoted the best feed conversion ratio. Hens fed the reference diet presented higher egg mass and better feed conversion ratio per kg eggs and per dozen eggs. Hens fed the diets with low crude protein level (12% had reduced nitrogen excretion, but presented worse egg production.

U.S. crude oil, natural gas, and natural gas liquids reserves 1995 annual report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-01

The EIA annual reserves report series is the only source of comprehensive domestic proved reserves estimates. This publication is used by the Congress, Federal and State agencies, industry, and other interested parties to obtain accurate estimates of the Nation`s proved reserves of crude oil, natural gas, and natural gas liquids. These data are essential to the development, implementation, and evaluation of energy policy and legislation. This report presents estimates of proved reserves of crude oil, natural gas, and natural gas liquids as of December 31, 1995, as well as production volumes for the US and selected States and State subdivisions for the year 1995. Estimates are presented for the following four categories of natural gas: total gas (wet after lease separation), nonassociated gas and associated-dissolved gas (which are the two major types of wet natural gas), and total dry gas (wet gas adjusted for the removal of liquids at natural gas processing plants). In addition, reserve estimates for two types of natural gas liquids, lease condensate and natural gas plant liquids, are presented. Also included is information on indicated additional crude oil reserves and crude oil, natural gas, and lease condensate reserves in nonproducing reservoirs. A discussion of notable oil and gas exploration and development activities during 1995 is provided. 21 figs., 16 tabs.

Crude glycerin in diets for feedlot Nellore cattle

Directory of Open Access Journals (Sweden)

Eric Haydt Castello Branco van Cleef

2014-02-01

Full Text Available Two studies were conducted to evaluate the effects of crude glycerin on feed intake, performance, carcass characteristics, and total digestibility of Nellore bulls. In experiment 1, cattle (n = 30 were fed a control diet without crude glycerin and diets containing 7.5, 15, 22.5, and 30% crude glycerin, for 103 d. Animals were harvested and data of carcass characteristics were collected. In experiment 2, a digestibility trial was performed using indigestible acid detergent fiber (iADF as internal marker, and five rumen-cannulated steers. Both experiments were conducted as a randomized complete block design and data were analyzed using mixed procedures. In experiment 1 no differences were observed among treatments on dry matter intake, and performance variables. Regarding carcass characteristics, no effect was observed, except for carcass fat estimates, which were greater in treatments with crude glycerin. In experiment 2, crude glycerin promoted a decrease in digestibility of fibrous fractions NDF and HEM, and increased digestibility of crude protein by 6%. Although it caused negative effect on digestibility of fibrous fraction of diets, crude glycerin can be a good energy source for Nellore bulls, since no losses are observed on performance and carcass characteristics when animals are fed up to 30% of this by-product.

The Effect of Crude Protein Content on Meat and Fat Production in Sheep

Science.gov (United States)

Mawati, S.; Restitrisnani, V.; Soedarsono

2018-02-01

This study was undertaken to evaluate the effect of crude protein (CP) content on meat protein and fat production in sheep. Twenty four male thin tail sheep aged 6-7 months with average body weight of 13±1.56 kg were used in this study. The sheep were fed 10-14% CP. Sheep with the average body weight amount 16.75 kg were slaughter after 4 months rising. Parameters observed in this study were carcass weight, meat weight and fat weight of thin tail sheep. The data were analyzed using correlation analysis. The result of this study showed that CP content on diet had weak and negative correlation with meat production (r = -0.06) (y = -0.148x + 62.54) but had weak and possitive correlation with fat production (r = 0.3) (y = 0.807x2 -18.40x + 119.1). Based on the result, it can be concluded that the optimum CP content for sheep is 12.5% CP.

Effect of subsidies to fossil fuel companies on United States crude oil production

Science.gov (United States)

Erickson, Peter; Down, Adrian; Lazarus, Michael; Koplow, Doug

2017-11-01

Countries in the G20 have committed to phase out `inefficient' fossil fuel subsidies. However, there remains a limited understanding of how subsidy removal would affect fossil fuel investment returns and production, particularly for subsidies to producers. Here, we assess the impact of major federal and state subsidies on US crude oil producers. We find that, at recent oil prices of US50 per barrel, tax preferences and other subsidies push nearly half of new, yet-to-be-developed oil investments into profitability, potentially increasing US oil production by 17 billion barrels over the next few decades. This oil, equivalent to 6 billion tonnes of CO2, could make up as much as 20% of US oil production through 2050 under a carbon budget aimed at limiting warming to 2 °C. Our findings show that removal of tax incentives and other fossil fuel support policies could both fulfil G20 commitments and yield climate benefits.

Impact of the rheological studies in the transport for pipeline of paraffinic crude oils

International Nuclear Information System (INIS)

Rodriguez, L; Vidales, H; Castaneda, M; Leal, O; Barrero R; Garzon, J

2000-01-01

The results of this applied research contribute fundamental elements for handling paraffinic crude oils (pipeline design and operation) and the optimization of the use of Pour Point Depressor additives. The rheological studies support the fluid-dynamic analyses that accurately predict the pipeline transport operation, unlike traditional parameters such as pour point and cloud point. Evaluations of rheological behavior was carried out at the laboratory level in concentric viscometers and were scaled at the pilot plant level in a fluid-dynamic test circuit in pipes with diameters from 1.27 to 15.24 cm (1/2 to 6 inches), where the laboratory scale was confirmed. The tests were performed under strain rate temperature and conditions similar to those of pipeline and flow line operation in production fields. Also, the viability to restart pumping after a prolonged shutdown with extreme temperatures was calculated, evaluating creep stress. The study has allowed us to transport Cupiagua crude oil without the PPD additive in a segregated manner, showing that despite its high pour point 300K (27 grades Celsius), in dynamic conditions similar to those in the pipeline, the crude oil flows at temperatures near 283K (10 Celsius degrades) without putting the integrity of the pipe in danger and within operational and equipment restrictions for the company operating the pipeline. This has generated significant savings, due to the additive as well as the possibility to segregate the crude oils, which facilitates the operation of the paraffin plant at the Barrancabermeja Industrial Complex

Aqueous-phase reforming of crude glycerol : effect of impurities on hydrogen production

NARCIS (Netherlands)

Boga, Dilek A.; Liu, Fang; Bruijnincx, Pieter C. A.; Weckhuysen, Bert M.

2016-01-01

The aqueous-phase reforming (APR) of a crude glycerol that originates from an industrial process and the effect of the individual components of crude glycerol on APR activity have been studied over 1 wt% Pt/Mg-Al) O, 1 wt% Pt/Al2O3, 5 wt% Pt/Al2O3 and 5 wt% Pt/C catalysts at 29 bar and 225 degrees

The future for heavy crude oil

International Nuclear Information System (INIS)

Horsnell, P.

1995-01-01

The expectation, still held in 1993, that the light oil-heavy crude oil differential would go on increasing in favour of light oil has not been fulfilled. Current perceptions are that heavy oil will continue to be relatively strong and there is no inevitable upward trend in light-heavy crude differentials. Non-OPEC production has grown significantly lighter overall in recent years and is likely to continue so for several more years. This is due to expanded light oil production in the North Sea, Latin America and the Far East, and contractions in heavy oil production in Russia and the USA. OPEC production has also become lighter with, in particular, an expansion in light oil and contraction in heavy grades from Saudi Arabia. At the same time, the nature of the demand from refineries has changed with the introduction of new units designed to process the residium from heavy oil distillation. Thus the supply of light oil has expanded while demand for it has contracted with the reverse being true for heavy oil. (2 figures, 1 table) (UK)

Development and growth of science-intensive production of lube oil additives in the transition to a market economy

International Nuclear Information System (INIS)

Zhurba, A.S.; Burlaka, G.G.; Pravikov, A.A.

1992-01-01

In the Soviet petroleum refining and petrochemical industry, preference with respect to science-intensive development should be given to lube oil additives as production objects which are characterized by high cost of scientific developments and which are major factors influencing scientific and technical progress in many branches of the economy. The role of additives is becoming much more significant because of dwindling resources of crude oils with high potential contents of lube fractions (18-20%); other factors are the phasing out of ecologically harmful technologies, unsatisfactory utilization of used oils, and so on. Under these conditions, the use of additives is essentially the only method for increasing the efficiency of lube oil production and improving the product quality, which, together with improved design and materials for the lubricating components and an improvement of the professional and cultural level of their operation, will logically bring forth a marked curtailment of lubricant consumption. Outside the USSR, additive production, thanks to its conversion into a rapidly progressing subbranch of the petroleum refining industry, has become the object of capital investment. Under conditions of a market economy, additive manufacture is characterized by a high level of specialization and concentration, various forms of cooperation, profitability, and competitiveness. Because of the existence of a branch network of retail and wholesale trade, production of lube oils and additives can be adjusted rapidly to meet the requirements of the domestic and world market

Enhancement of biodegradation of crude petroleum-oil in contaminated water by the addition of nitrogen sources.

Science.gov (United States)

Mukred, A M; Hamid, A A; Hamzah, A; Yusoff, W M Wan

2008-09-01

Addition of nitrogen sources as supplementary nutrient into MSM medium to enhance biodegradation by stimulating the growth four isolates, Acinetobacter faecalis, Staphylococcus sp., Pseudomonas putida and Neisseria elongata isolated from petroleum contaminated groundwater, wastewater aeration pond and biopond at the oil refinery Terengganu Malaysia was investigated. The organic nitrogen sources tested not only supported growth but also enhances biodegradation of 1% Tapis crude oil. All four isolates showed good growth especially when peptone was employed as the organic nitrogen compared to growth in the basal medium. Gas chromatography showed that more then 91, 93, 94 and 95% degradation of total hydrocarbon was observed after 5 days of incubation by isolates Pseudomonas putida, Neisseria elongate, Acinetobacter faecalis and Staphylococcus sp., respectively.

Additives effect on chemical composition and quality of sisal co-product silage

Directory of Open Access Journals (Sweden)

Luiz Gustavo Neves Brandão

2013-12-01

Full Text Available Fermentation profile and nutritional value of sisal co-product silage (SC subjected to seven treatments (additives, were evaluated. The SC was ensiled in natura and added with: soy meal, urea, wheat meal, palm kernel cake, A. sisalana dust, licuri cake and cottonseed cake. Experimental silos with capacity for approximately 15 kg of silage, were used. The silos were opened 60 days after ensilage process. It was used a completely randomized design with three replications. The SC in natura present low values of dry mater (DM 12.3% and the additives increased dry matter silages, exception for urea. The SC silage additivated with soybean meal (pH 4.9 and palm kernel cake (butyric acid = 0.07% DM differed, respectively, for pH and butyric acid, compared with in natura SC silage (pH = 4.1 and butyric acid = 0.03% DM. The addition of soybean meal, urea, cottonseed meal, wheat bran and palm kernel, increased crude protein (CP of in natura SC silage. The NDF in silage increased with addition of cottonseed meal or palm kernel cake (60.1 and 66.2% DM in relation in natura SC silage (42.9% DM. The in natura and additivated silages of SC were considered as good or excellent quality.

Digestible energy of crude glycerol for pacu and silver catfish

Directory of Open Access Journals (Sweden)

Rafael Ernesto Balen

2014-01-01

Full Text Available The increase in global biodiesel production is originating a glycerol surplus, which has no defined destination. An alternative to overcome this problem is its use as energy source in animal feeding. In Brazil, Pacu (Piaractus mesopotamicus is one of the most farmed native fish species, whereas Silver catfish (Rhamdia quelen is suitable for production in subtropical region. Considering little knowledge about crude glycerol utilization in feeds for Neotropical fish species, it was evaluated the apparent digestibility coefficients (ADCs for energy of crude glycerol for P. mesopotamicus and R. quelen. The digestibility and digestible energy content of crude glycerol can be considered excellent even when compared to energy of common ingredients such as maize and wheat, presenting 0.97 and 0.89 of energy ADCs, and 15.2 and 13.95MJ kg-1 of digestible energy for Pacu and Silver catfish, respectively. In conclusion, crude glycerol is an energetic ingredient with good potential in Brazilian native fish diets.

Process development study on production of uranium metal from monazite sourced crude uranium tetra-fluoride

International Nuclear Information System (INIS)

Chowdhury, S; Satpati, S.K.; Hareendran, K.N.; Roy, S.B.

2014-01-01

Development of an economic process for recovery, process flow sheet development, purification and further conversion to nuclear grade uranium metal from the crude UF 4 has been a technological challenge and the present paper, discusses the same.The developed flow-sheet is a combination of hydrometallurgical and pyrometallurgical processes. Crude UF 4 is converted to uranium di-oxide (UO 2 ) by chemical conversion route and UO 2 produced is made fluoride-free by repeated repulping, followed by solid liquid separation. Uranium di-oxide is then purified by two stages of dissolution and suitable solvent extraction methods to get uranium nitrate pure solution (UNPS). UNPS is then precipitated with air diluted ammonia in a leak tight stirred vessel under controlled operational conditions to obtain ammonium di-uranate (ADU). The ADU is then calcined and reduced to produce metal grade UO 2 followed by hydro-fluorination using anhydrous hydrofluoric acid to obtain metal grade UF 4 with ammonium oxalate insoluble (AOI) content of 4 is essential for critical upstream conversion process. Nuclear grade uranium metal ingot is finally produced by metallothermic reduction process at 650℃ in a closed vessel, called bomb reactor. In the process, metal-slag separation plays an important role for attaining metal purity as well as process yield. Technological as well economic feasibility of indigenously developed process for large scale production of uranium metal from the crude UF 4 has been established in Bhabha Atomic Research Centre (BARC), India

Long-term Effects of Nutrient Addition and Phytoremediation on Diesel and Crude Oil Contaminated Soils in subarctic Alaska

Science.gov (United States)

Leewis, Mary-Cathrine; Reynolds, Charles M.; Leigh, Mary Beth

2014-01-01

Phytoremediation is a potentially inexpensive method of detoxifying contaminated soils using plants and associated soil microorganisms. The remote locations and cold climate of Alaska provide unique challenges associated with phytoremediation such as finding effective plant species that can achieve successful site clean-up despite the extreme environmental conditions and with minimal site management. A long-term assessment of phytoremediation was performed which capitalized on a study established in Fairbanks in 1995. The original study sought to determine how the introduction of plants (Festuca rubra, Lolium multiflorum), nutrients (fertilizer), or their combination would affect degradation of petroleum hydrocarbon (TPH) contaminated soils (crude oil or diesel) over time. Within the year following initial treatments, the plots subjected to both planting and/or fertilization showed greater overall decreases in TPH concentrations in both the diesel and crude oil contaminated soils relative to untreated plots. We re-examined this field site after 15 years with no active site management to assess the long-term effects of phytoremediation on colonization by native and non-native plants, their rhizosphere microbial communities and on petroleum removal from soil. Native and non-native vegetation had extensively colonized the site, with more abundant vegetation found on the diesel contaminated soils than the more nutrient-poor, more coarse, and acidic crude oil contaminated soils. TPH concentrations achieved regulatory clean up levels in all treatment groups, with lower TPH concentrations correlating with higher amounts of woody vegetation (trees & shrubs). In addition, original treatment type has affected vegetation recruitment to each plot with woody vegetation and more native plants in unfertilized plots. Bacterial community structure also varies according to the originally applied treatments. This study suggests that initial treatment with native tree species in

Optimization model of a system of crude oil distillation units with heat integration and metamodeling

International Nuclear Information System (INIS)

Lopez, Diana C; Mahecha, Cesar A; Hoyos, Luis J; Acevedo, Leonardo; Villamizar Jaime F

2010-01-01

The process of crude distillation impacts the economy of any refinery in a considerable manner. Therefore, it is necessary to improve it taking good advantage of the available infrastructure, generating products that conform to the specifications without violating the equipment operating constraints or plant restrictions at industrial units. The objective of this paper is to present the development of an optimization model for a Crude Distillation Unit (CDU) system at a ECOPETROL S.A. refinery in Barrancabermeja, involving the typical restrictions (flow according to pipeline capacity, pumps, distillation columns, etc) and a restriction that has not been included in bibliographic reports for this type of models: the heat integration of streams from Atmospheric Distillation Towers (ADTs) and Vacuum Distillation Towers (VDT) with the heat exchanger networks for crude pre-heating. On the other hand, ADTs were modeled with Metamodels in function of column temperatures and pressures, pump a rounds flows and return temperatures, stripping steam flows, Jet EBP ASTM D-86 and Diesel EBP ASTM D-86. Pre-heating trains were modeled with mass and energy balances, and design equation of each heat exchanger. The optimization model is NLP, maximizing the system profit. This model was implemented in GAMSide 22,2 using the CONOPT solver and it found new operating points with better economic results than those obtained with the normal operation in the real plants. It predicted optimum operation conditions of 3 ADTs for constant composition crude and calculated the yields and properties of atmospheric products, additional to temperatures and duties of 27 Crude Oil exchangers.

How much crude oil can zooplankton ingest? Estimating the quantity of dispersed crude oil defecated by planktonic copepods

International Nuclear Information System (INIS)

Almeda, Rodrigo; Connelly, Tara L.; Buskey, Edward J.

2016-01-01

We investigated and quantified defecation rates of crude oil by 3 species of marine planktonic copepods (Temora turbinata, Acartia tonsa, and Parvocalanus crassirostris) and a natural copepod assemblage after exposure to mechanically or chemically dispersed crude oil. Between 88 and 100% of the analyzed fecal pellets from three species of copepods and a natural copepod assemblage exposed for 48 h to physically or chemically dispersed light crude oil contained crude oil droplets. Crude oil droplets inside fecal pellets were smaller (median diameter: 2.4–3.5 μm) than droplets in the physically and chemically dispersed oil emulsions (median diameter: 6.6 and 8.0 μm, respectively). This suggests that copepods can reject large crude oil droplets or that crude oil droplets are broken into smaller oil droplets before or during ingestion. Depending on the species and experimental treatments, crude oil defecation rates ranged from 5.3 to 245 ng-oil copepod"−"1 d"−"1, which represent a mean weight-specific defecation rate of 0.026 μg-oil μg-C_c_o_p_e_p_o_d"1 d"−"1. Considering a dispersed crude oil concentration commonly found in the water column after oil spills (1 μl L"−"1) and copepod abundances in high productive coastal areas, copepods may defecate ∼1.3–2.6 mg-oil m"−"3 d"−"1, which would represent ∼0.15%–0.30% of the total dispersed oil per day. Our results indicate that ingestion and subsequent defecation of crude oil by planktonic copepods has a small influence on the overall mass of oil spills in the short term, but may be quantitatively important in the flux of oil from surface water to sediments and in the transfer of low-solubility, toxic petroleum hydrocarbons into food webs after crude oil spills in the sea. - Highlights: • Copepods exposed to dispersed crude oil produced fecal pellets contained numerous small oil droplets (2.4 to 3.5 µm). • Copepods could reject large oil droplets or oil droplets are broken into

Standard guide for determining corrosivity of crude oils

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This guide presents some generally accepted laboratory methodologies that are used for determining the corrosivity of crude oil. 1.2 This guide does not cover detailed calculations and methods, but rather a range of approaches that have found application in evaluating the corrosivity of crude oil. 1.3 Only those methodologies that have found wide acceptance in crude oil corrosivity evaluation are considered in this guide. 1.4 This guide does not address the change in oil/water ratio caused by accumulation of water at low points in a pipeline system. 1.5 This guide is intended to assist in the selection of methodologies that can be used for determining the corrosivity of crude oil under conditions in which water is present in the liquid state (typically up to 100°C). These conditions normally occur during oil and gas production, storage, and transportation in the pipelines. 1.6 This guide does not cover the evaluation of corrosivity of crude oil at higher temperatures (typically above 300°C) that oc...

The impacts of the export ban on Alaskan crude oil trade

International Nuclear Information System (INIS)

Farah, P.G.; Bausell, C.W.; Vogelsang, A.

1990-01-01

The authors investigated the petroleum markets impacts of lifting the ban on Alaska North Slope (ANS) crude oil exports. This paper reports on some aspects of this investigation. The economic analysis relied heavily on the modeling of the ANS crude trade conducted on behalf of GAO by the Energy Information Administration (EIA) using the Transportation and Refining of International Petroleum model (TRIP). In contrast to previous studies, this one suggests that transportation costs may not be the only major factor in the realignment of ANS crude trade in response to lifting the ban. The differences in the yields of ANS crude and various crudes used by refiners in Pacific Rim countries on the one hand, and the product demand slates of the US West Coast and the potential buyers of ANS crude in Pacific Rim may also figure prominently in determining the reallocation of ANS crude if exports are permitted

Compositional thermodynamic modelling of crystallization in waxy crudes; Modelisation thermodynamique compositionnelle de la cristallisation des bruts paraffiniques

Energy Technology Data Exchange (ETDEWEB)

Calange, S.

1996-06-26

During waxy crudes production, the risks of solid deposits formation, mainly in wells and in transport lines, are to be considered. These risks prevention induces high exploitation costs, and sometimes production losses. A better knowledge of the phenomena involved should allow an optimization of production conditions and thus cost reduction. With such objectives, we have developed a compositional thermodynamic model which allows to compute both the Wax Appearance Temperature and the amount of precipitated solid for lower temperatures. We have also implemented an experimental procedure in order to measure the solid deposit curve for a given crude under atmospheric pressure. The model can be used by means of a computer programme called `CRYSPAR`. This model takes into account the non-ideality of the solid phase through the one-parameter Margules equation. Thus it is only necessary to fit this unique parameter on the deposit quantities measured in the laboratory. The value thus determined will further allow the prediction of the deposition curves for crudes when their composition is changed, particularly by solvent addition. The experimental technique used is Differential Scanning Calorimetry (DSC). DSC is fast, easy to use and available in the laboratories of oil companies. (author) 181 refs.

Western Canadian crude oil supply and markets 2002-2010 : Executive summary

International Nuclear Information System (INIS)

2003-08-01

The forecast of crude supply developed by the Canadian Association of Petroleum Producers (CAPP) indicates that additional pipeline capacity from western Canada to existing new markets will be required. A crude market study was undertaken to investigate and assess the potential development of the North American crude markets along with expected western Canadian crude supply growth. The results revealed that additional crude export capacity from Alberta will be required by 2006 or 2007. An analysis of three export pipeline scenarios was carried out: (1) Hardisty to Chicago, with a further extension to Cushing, Oklahoma, (2) Edmonton to the west coast of British Columbia, Prince Rupert, and (3) Hardisty to California. The most attractive aggregate benefits to heavy crude producers would result from a western export pipeline to British Columbia or California. A superior alternative is a pipeline to a deepwater tanker terminal on the coast of British Columbia. The Chicago pipeline option would become more attractive if Midwestern refiners were to expand their capacity to process heavy oil. Declining netbacks associated with sustained growth that is introduced into the market place are reflected in all scenarios over the forecast period until 2010. 1 tab., 23 figs

Remediation trials of crude oil contaminated soil using different ...

African Journals Online (AJOL)

A 3 month remediation trial of the use of detergent and sawdust in different combination forms in the restoration of a crude oil contaminated tropical soil was investigated. 8 remediation treatments labeled A – H in addition to the control (I) were used in 10 kg soil artificially polluted with 300 ml crude oil each. Remediation ...

Biosurfactant production from marine hydrocarbon-degrading consortia and pure bacterial strains using crude oil as carbon source.

Science.gov (United States)

Antoniou, Eleftheria; Fodelianakis, Stilianos; Korkakaki, Emmanouela; Kalogerakis, Nicolas

2015-01-01

Biosurfactants (BSs) are "green" amphiphilic molecules produced by microorganisms during biodegradation, increasing the bioavailability of organic pollutants. In this work, the BS production yield of marine hydrocarbon degraders isolated from Elefsina bay in Eastern Mediterranean Sea has been investigated. The drop collapse test was used as a preliminary screening test to confirm BS producing strains or mixed consortia. The community structure of the best consortia based on the drop collapse test was determined by 16S-rDNA pyrotag screening. Subsequently, the effect of incubation time, temperature, substrate and supplementation with inorganic nutrients, on BS production, was examined. Two types of BS - lipid mixtures were extracted from the culture broth; the low molecular weight BS Rhamnolipids and Sophorolipids. Crude extracts were purified by silica gel column chromatography and then identified by thin layer chromatography and Fourier transform infrared spectroscopy. Results indicate that BS production yield remains constant and low while it is independent of the total culture biomass, carbon source, and temperature. A constant BS concentration in a culture broth with continuous degradation of crude oil (CO) implies that the BS producing microbes generate no more than the required amount of BSs that enables biodegradation of the CO. Isolated pure strains were found to have higher specific production yields than the complex microbial marine community-consortia. The heavy oil fraction of CO has emerged as a promising substrate for BS production (by marine BS producers) with fewer impurities in the final product. Furthermore, a particular strain isolated from sediments, Paracoccus marcusii, may be an optimal choice for bioremediation purposes as its biomass remains trapped in the hydrocarbon phase, not suffering from potential dilution effects by sea currents.

Crude imports to U.S. Gulf Coast refineries to accelerate

International Nuclear Information System (INIS)

Anon.

1995-01-01

The largest crude oil commodity market in the world--the US Gulf Coast--has experienced an important change in recent years. The decline in domestic production and the increase in imports appear destined to accelerate in the coming decades. Latin American countries will continue to be a major source of US imports, and that the shortfall will have to be made up using Middle Eastern crudes, primarily those from Saudi Arabia and Kuwait. The paper discusses economics, US production, imports, and future trends

CFD modeling of fouling in crude oil pre-heaters

International Nuclear Information System (INIS)

Bayat, Mahmoud; Aminian, Javad; Bazmi, Mansour; Shahhosseini, Shahrokh; Sharifi, Khashayar

2012-01-01

Highlights: ► A conceptual CFD-based model to predict fouling in industrial crude oil pre-heaters. ► Tracing fouling formation in the induction and developing continuation periods. ► Effect of chemical components, shell-side HTC and turbulent flow on the fouling rate. - Abstract: In this study, a conceptual procedure based on the computational fluid dynamic (CFD) technique has been developed to predict fouling rate in an industrial crude oil pre-heater. According to the developed CFD concept crude oil was assumed to be composed of three pseudo-components comprising of petroleum, asphaltene and salt. The binary diffusion coefficients were appropriately categorized into five different groups. The species transport model was applied to simulate the mixing and transport of chemical species. The possibility of adherence of reaction products to the wall was taken into account by applying a high viscosity for the products in competition with the shear stress on the wall. Results showed a reasonable agreement between the model predictions and the plant data. The CFD model could be applied to new operating conditions to investigate the details of the crude oil fouling in the industrial pre-heaters.

Optimal Physical and Nutrient Parameters for Growth of Trichoderma virens UKMP-1M for Heavy Crude Oil Degradation

International Nuclear Information System (INIS)

Ainon Hamzah; Buzarin, M.A.; Aidil Abdul Hamid; Thmanomar, O.; Sahidan Senafi

2012-01-01

This study was carried out to determine the optimal parameters for the production of biomass of Trichoderma virens UKMP-1M, a fungus isolated from oil-polluted wastewater. The isolate showed maximum growth at day six after incubation in Mineral Salt Medium (MSM) in the presence of 3 % (v/ v) heavy Khefji Sour crude oil. Although it grew at pH between 5.0 and 7.0, it grew best at pH 5.5. T. virens UKMP-1M grew at temperatures between 25 and 35 degree Celsius, with its highest growth at 30 degree Celsius. Aeration by agitation at 200 rpm was shown to yield the greatest biomass. Peptone at concentration of 1.5 % (w/ v) was determined to be a better nitrogen source than urea, potassium nitrate (KNO 3 ), yeast extract, ammonium sulphate ((NH 4 ) 2 SO 4 ) and ammonium chloride (NH 4 Cl). Addition of 1 % (v/ v) crude oil to the MSM medium led to higher biomass production than the addition of 3 %, 5 %, 7 % and 10 % (v/ v) crude oil. The result also revealed that 40 % of total petroleum hydrocarbon (TPH), 100 % of pristane and 74 % of phytane compounds were degraded after 9 days of incubation at optimal physical and nutrient parameters. (author)

Agricultural Commodities and Crude Oil Prices: An Empirical Investigation of Their Relationship

Directory of Open Access Journals (Sweden)

Eleni Zafeiriou

2018-04-01

Full Text Available Within the last few decades, the extended use of biodiesel and bioethanol has established interlinkages between energy markets and agricultural commodity markets. The present work examines the bivariate relationships of crude oil–corn and crude oil–soybean futures prices with the assistance of the ARDL cointegration approach. Our findings confirm that crude oil prices affect the prices of agricultural products used in the production of biodiesel, as well as of ethanol, validating the interaction of energy and agricultural commodity markets. The practical value of the present work is that the findings provide policy makers with insight into the interlinkages between agricultural and energy markets to promote biodiesel or bioethanol by affecting crude oil prices. The novelty of the present work stands on the use of futures prices that incorporate all available information and thus are more appropriate to identify supply and demand shocks and price spillovers than real prices. Finally, the period of study includes extremely low, as well as extremely high, crude oil prices and the results illustrate that biofuels cannot be substituted for crude oil and protect economies from energy volatility.

A new vehicle for herbicide application using crude glycerin, a by ...

African Journals Online (AJOL)

This work aimed to develop oil-in-water (O/W) emulsions using crude glycerin treated with ... The crude glycerin was used to develop five stable emulsions with promising ..... Biodiesel and renewable diesel: A comparison. Progr. Energy Combust. Sci. ... Production, consumption, prices, characterization and new trends in.

Optimization model of a system of crude oil distillation units whit heat integration and meta modeling

International Nuclear Information System (INIS)

Lopez, Diana C; Mahecha, Cesar A; Hoyos, Luis J; Acevedo, Leonardo; Villamizar Jaime F

2009-01-01

The process of crude distillation impacts the economy of any refinery in a considerable manner. Therefore, it is necessary to improve it taking good advantage of the available infrastructure, generating products that conform to the specifications without violating the equipment operating constraints or plant restrictions at industrial units. The objective of this paper is to present the development of an optimization model for a Crude Distillation Unit (CDU) system at a ECOPETROL S.A. refinery in Barrancabermeja, involving the typical restrictions (flow according to pipeline capacity, pumps, distillation columns, etc) and a restriction that has not been included in bibliographic reports for this type of models: the heat integration of streams from Atmospheric Distillation Towers (ADTs) and Vacuum Distillation Towers (VDT) with the heat exchanger networks for crude pre-heating. On the other hand, ADTs were modeled with Meta models in function of column temperatures and pressures, pumparounds flows and return temperatures, stripping steam flows, Jet EBP ASTM D-86 and Diesel EBP ASTM D-86. Pre-heating trains were modeled with mass and energy balances, and design equation of each heat exchanger. The optimization model is NLP, maximizing the system profit. This model was implemented in GAMSide 22,2 using the CONOPT solver and it found new operating points with better economic results than those obtained with the normal operation in the real plants. It predicted optimum operation conditions of 3 ADTs for constant composition crude and calculated the yields and properties of atmospheric products, additional to temperatures and duties of 27 Crude Oil exchangers.

Bioremediation potential of crude oil spilled on soil

International Nuclear Information System (INIS)

McMillen, S.J.; Young, G.N.; Davis, P.S.; Cook, P.D.; Kerr, J.M.; Gray, N.R.; Requejo, A.G.

1995-01-01

Spills sometimes occur during routine operations associated with exploration and production (E and P) of crude oil. These spills at E and P sites typically are small, less than 1 acre (0.4 ha), and the spill may be in remote locations. As a result, bioremediation often represents a cost-effective alternative to other cleanup technologies. The goal of this study was to determine the potential for biodegrading a range of crude oil types and determining the effect of process variables such as soil texture and soil salinity. Crude oils evaluated ranged in American Petroleum institute (API) gravity from 14 degree to 45 degree. The extent of biodegradation was calculated from oxygen uptake data and the total extractable material (TEM) concentration. Based on the data collected, a simple model was developed for predicting the bioremediation potential of a range of crude oil types. Biodegradation rates were significantly lower in sandy soils. Soil salinities greater than approximately 40 mmhos/cm adversely impacted soil microbial activity and biodegradation rate

Solids precipitation in crude oils, gas-to-liquids and their blends

Science.gov (United States)

Ramanathan, Karthik

Gas-to-liquids (GTL) liquids are obtained from syngas by the Fischer-Tropsch synthesis. The blending of GTL liquids produced from natural gas/coal reserves and crude oils is a possibility in the near future for multiple reasons. Solids precipitation is a major problem in pipelines and refineries leading to significant additional operating costs. The effect of the addition of a paraffinic GTL liquid to crude oils on solids precipitation was investigated in this study. A Fourier transform infrared (FT-IR) spectroscopic technique was used to obtain solid-liquid equilibria (SLE) data for the various samples. The SLE of multiple systems of model oils composed of n-alkanes was investigated preliminarily. Blends of a model oil simulating a GTL liquid composition and a crude oil showed that the wax precipitation temperature (WPT) decreased upon blending. Three crude oils from different geographic regions (Alaskan North Slope, Colorado and Venezuela) and a laboratory-produced GTL liquid were used in the preparation of blends with five different concentrations of the GTL liquid. The wax precipitation temperatures of the blends were found to decrease with the increasing addition of the GTL liquid for all the oils. This effect was attributed to the solvent effect of the low molecular weight-paraffinic GTL liquid on the crude oils. The weight percent solid precipitated that was estimated as a function of temperature did not show a uniform trend for the set of crude oils. The asphaltene onset studies done on the blends with near-infrared spectroscopy indicated that the addition of GTL liquid could have a stabilizing effect on the asphaltenes in some oils. Analytical techniques such as distillation, solvent separation, HPLC, GC, and GPC were used to obtain detailed composition data on the samples. Two sets of compositional data with 49 and 86 pseudo-components were used to describe the three crude oils used in the blending work. The wax precipitation was calculated using a

Kinetics and Thermal Properties of Crude and Purified β-Galactosidase with Potential for the Production of Galactooligosaccharides

Directory of Open Access Journals (Sweden)

Anna Rafaela Cavalcante Braga

2013-01-01

Full Text Available β-Galactosidase is an enzyme that catalyzes the hydrolysis of lactose. It has potential importance due to various applications in the food and dairy industries, involving lactose-reduced ingredients. The properties of two β-galactosidase enzymes, crude and purified, from different sources, Kluyveromyces marxianus CCT 7082 and Kluyveromyces marxianus ATCC 16045, were analyzed. The pH and temperature optima, deactivation energy, thermal stability and kinetic and thermodynamic parameters were determined, as well as the ability to hydrolyze lactose and produce galactooligosaccharides. Purification process improved the properties of the enzymes, and the results showed that purified enzymes from both strains had a higher optimum temperature, and lower values of Km, thus showing greater affinity for o-nitrophenyl-β-D-galactopiranoside than the crude enzymes. The production of galactooligosaccharides was also greater when using purified enzymes, increasing the synthesis by more than 30 % by both strains.

Upgrading of heavy crude oil with supported and unsupported transition metals

Energy Technology Data Exchange (ETDEWEB)

Nares, H.R.; Schacht-Hernandez, P.; Cabrera-Reyes, M.C.; Ramirez-Garnica, M.; Cazarez-Candia, O. [Instituto Mexicano del Petroleo, Atepehuacan (Mexico)

2006-07-01

Heavy crude oil presents many problems such as difficulty in transportation, low processing capacity in refineries, and low mobility through the reservoir due to high viscosity which affects the index of productivity of the wells. Because of these challenges, it is necessary to enhance heavy crude oil, both aboveground and underground. The effects of several metallic oxides used to upgrade heavy crude oil properties were examined in order to increase the mobility of reservoir oil by reducing viscosity and improving the quality of the oil. This can be accomplished by reducing the asphaltene and sulfur contents and increasing the American Petroleum Institute (API) gravity using transition metal supported in alumina and unsupported from transition metals derived from either acetylacetonate or alkylhexanoate in liquid phase homogeneously mixed with heavy crude oil as well as metal transition supported in alumina. KU-H heavy crude oil from the Golf of Mexico was studied. The results were obtained by Simulated Distillation and True Boiling Point (TBP). It was concluded that the use of crude oil thermal hydrocracking allowed the API gravity to increase and considerably reduce the viscosity. As a result, the productivity index in wells was increased. However there is a high formation of coke that could damage the conductivity of the rock and then reduce the potential of oil recovery. 27 refs., 3 tabs., 5 figs.

Crude glycerol combustion: Particulate, acrolein, and other volatile organic emissions

KAUST Repository

Steinmetz, Scott

2013-01-01

Crude glycerol is an abundant by-product of biodiesel production. As volumes of this potential waste grow, there is increasing interest in developing new value added uses. One possible use, as a boiler fuel for process heating, offers added advantages of energy integration and fossil fuel substitution. However, challenges to the use of crude glycerol as a boiler fuel include its low energy density, high viscosity, and high autoignition temperature. We have previously shown that a refractory-lined, high swirl burner can overcome challenges related to flame ignition and stability. However, critical issues related to ash behavior and the possible formation of acrolein remained. The work presented here indicates that the presence of dissolved catalysts used during the esterification and transesterification processes results in extremely large amounts of inorganic species in the crude glycerol. For the fuels examined here, the result is a submicron fly ash comprised primarily of sodium carbonates, phosphates, and sulfates. These particles report to a well-developed accumulation mode (0.3-0.7 μm diameter), indicating extensive ash vaporization and particle formation via nucleation, condensation, and coagulation. Particle mass emissions were between 2 and 4 g/m3. These results indicate that glycerol containing soluble catalyst is not suitable as a boiler fuel. Fortunately, process improvements are currently addressing this issue. Additionally, acrolein is of concern due to its toxicity, and is known to be formed from the low temperature thermal decomposition of glycerol. Currently, there is no known reliable method for measuring acrolein in sources. Acrolein and emissions of other volatile organic compounds were characterized through the use of a SUMMA canister-based sampling method followed by GC-MS analysis designed for ambient measurements. Results indicate crude glycerol combustion produces relatively small amounts of acrolein (∼15 ppbv) and other volatile organic

Crude oil pricing in Asia and future problems; Asia no gen`yu pricing to kongo no kadai

Energy Technology Data Exchange (ETDEWEB)

Kato, T. [The Institute of Energy Economics, Tokyo (Japan)

1997-01-30

This paper describes pricing factors of crude oil for Asia and future problems. Price of the Middle East crude oil for Asia is determined by linking the spot price of Dubayy crude oil using as a marker. Factors affecting the pricing of marker crude oil include the information dispatching functions for prices of spot market and paper market of marker crude oil, the presence of competitive crude oil, and the correlation between market of oil products and price of crude oil. The paper market of Dubayy crude oil with a small scale of trading provides poor impact and transparency. In Asia, there is no strong competitive crude oil except the Middle East crude oil. There is only a weak price linking between crude oil and products. These are the background that the price of Middle East crude oil stays at the high level and the price adjusting functions are hard to work. The marker crude oil should be changed to another except Dubayy crude oil, and information should be dispatched from purchasers based on the stable standard crude oil. The real paper market should be created, and the force of speaking to oil producing countries should be enhanced by concentrating forces of major oil consuming countries in Asia. It is necessary to find out competitive crude oils. 5 figs., 6 tabs.

Biosurfactant production from marine hydrocarbon-degrading consortia and pure bacterial strains using crude oil as carbon source

Science.gov (United States)

Antoniou, Eleftheria; Fodelianakis, Stilianos; Korkakaki, Emmanouela; Kalogerakis, Nicolas

2015-01-01

Biosurfactants (BSs) are “green” amphiphilic molecules produced by microorganisms during biodegradation, increasing the bioavailability of organic pollutants. In this work, the BS production yield of marine hydrocarbon degraders isolated from Elefsina bay in Eastern Mediterranean Sea has been investigated. The drop collapse test was used as a preliminary screening test to confirm BS producing strains or mixed consortia. The community structure of the best consortia based on the drop collapse test was determined by 16S-rDNA pyrotag screening. Subsequently, the effect of incubation time, temperature, substrate and supplementation with inorganic nutrients, on BS production, was examined. Two types of BS – lipid mixtures were extracted from the culture broth; the low molecular weight BS Rhamnolipids and Sophorolipids. Crude extracts were purified by silica gel column chromatography and then identified by thin layer chromatography and Fourier transform infrared spectroscopy. Results indicate that BS production yield remains constant and low while it is independent of the total culture biomass, carbon source, and temperature. A constant BS concentration in a culture broth with continuous degradation of crude oil (CO) implies that the BS producing microbes generate no more than the required amount of BSs that enables biodegradation of the CO. Isolated pure strains were found to have higher specific production yields than the complex microbial marine community-consortia. The heavy oil fraction of CO has emerged as a promising substrate for BS production (by marine BS producers) with fewer impurities in the final product. Furthermore, a particular strain isolated from sediments, Paracoccus marcusii, may be an optimal choice for bioremediation purposes as its biomass remains trapped in the hydrocarbon phase, not suffering from potential dilution effects by sea currents. PMID:25904907

A refined approach: Saudi Arabia moves beyond crude

International Nuclear Information System (INIS)

Krane, Jim

2015-01-01

Saudi Arabia's role in global energy markets is changing. The kingdom is reshaping itself as a supplier of refined petroleum products while moving beyond its long-held role as a simple exporter of crude oil. This change is commensurate with the typical development trajectory of a state progressing to a more advanced stage of global economic integration. Gains from increased refining include reducing fuel imports and capturing margins now bequeathed to competitors. Refining also allows the kingdom to export its heavy crude oil to a wider array of customers, beyond select importers configured to handle heavy crudes. However, the move also presents strategic complications. The world's 'swing supplier' of oil may grow less willing or able to adjust supply to suit market demands. In the process, Saudi Arabia may have to update the old “oil for security” relationship that links it with Washington, augmenting it with a more diverse set of economic and investment ties with individual companies and countries, including China. -- Highlights: •Saudi Arabia is diverting crude oil into an expanding refining sector. •In doing so, the kingdom is moving beyond its role as global “swing supplier” of crude oil. •The kingdom will benefit from increased refining, including enhanced demand for heavy crude. •Strategic complications may force it to seek security partners beyond Washington

Production of ethyl ester from crude palm oil by two-step reaction using continuous microwave system

Directory of Open Access Journals (Sweden)

Sukritthira Ratanawilai

2011-02-01

Full Text Available The esterification of free fatty acids (FFA in vegetable oils with alcohol using an acid catalyst is a promising methodto convert FFA into valuable ester and obtain a FFA-free oil that can be further transesterified using alkali bases. In thiswork, the direct esterification reaction of FFA in crude palm oil to ethyl ester by continuous microwave was studied and theeffects of the main variables involved in the process, amount of catalyst, reaction time and the molar ratio oil/ alcohol, wereanalyzed. The optimum condition for the continuous esterification process was carried out with a molar ratio of oil to ethanol1:6, using 1.25%wt of H2SO4/oil as a catalyst, microwave power of 78 W and a reaction time 90 min. This esterification processshows that the amount of FFA was reduced from 7.5%wt to values around 1.4 %wt. Similar results were obtained followingconventional heating at 70°C, but only after a reaction time of 240 min. The esterified crude palm oil is suitable to perform thetransesterification process. Transesterification of the esterified palm oil has been accomplished with a molar ratio of oil toethanol of 1:8.5, 2.5%wt of KOH as a catalyst, a microwave power of 78 W, and a reaction time of 7 min. In addition, theproblem of glycerin separation was solved by mixing 10%wt of pure glycerin into the ethyl ester to induce the glycerin fromthe reaction to separated. This two-step esterification and transesterification process provided a yield of 78%wt with anester content of 97.4%wt. The final ethyl ester product met with the specifications stipulated by ASTM D6751-02.

Well-to-refinery emissions and net-energy analysis of China's crude-oil supply

Science.gov (United States)

Masnadi, Mohammad S.; El-Houjeiri, Hassan M.; Schunack, Dominik; Li, Yunpo; Roberts, Samori O.; Przesmitzki, Steven; Brandt, Adam R.; Wang, Michael

2018-03-01

Oil is China's second-largest energy source, so it is essential to understand the country's greenhouse gas emissions from crude-oil production. Chinese crude supply is sourced from numerous major global petroleum producers. Here, we use a per-barrel well-to-refinery life-cycle analysis model with data derived from hundreds of public and commercial sources to model the Chinese crude mix and the upstream carbon intensities and energetic productivity of China's crude supply. We generate a carbon-denominated supply curve representing Chinese crude-oil supply from 146 oilfields in 20 countries. The selected fields are estimated to emit between 1.5 and 46.9 g CO2eq MJ-1 of oil, with volume-weighted average emissions of 8.4 g CO2eq MJ-1. These estimates are higher than some existing databases, illustrating the importance of bottom-up models to support life-cycle analysis databases. This study provides quantitative insight into China's energy policy and the economic and environmental implications of China's oil consumption.

Enzymatic production of cellulose nanofibers from oil palm empty fruit bunch (EFB) with crude cellulase of Trichoderma sp.

Science.gov (United States)

Aditiawati, Pingkan; Dungani, Rudi; Amelia, Cindy

2018-03-01

Oil palm empty fruit bunch (EFB) biomass was used as a source for isolation of cellulose nanofibers (CNF) using enzymatic method. Non-cellulosic component were removed from biomass by delignification process using inoculum of Marasmius sp. Nanocellulose production began with cryocrushing pre-treatment, enzyme addition, and post-treatment with sonication. In enzyme addition, crushed EFB suspended in sodium-citrate buffer and various percentage of crude cellulase enzyme from Trichoderma sp. which is 50%, 100%, and 200% (v/w), followed by incubation in various period which is 2, 3, and 4 days. Particle size analyzer, Scanning electron microscopy and Fourier-transmmission infrared spectroscopy were used to determine the properties of CNF. Maximum CNF size distribution of 2, 3, and 4 days incubation period was 30.717 and 70 nm, respectively (50% (v/w)); 94.75 and 635 nm, respectively (100% (v/w)); 837.51 and 433 nm, respectively (200% (v/w)). Almost 100% yield achieved from variation of 50% (v/w) enzyme and 2 days incubation period. FTIR spectroscopy analysis showed that some impurities in nanocellulose. SEM analysis showed that fibril nanocellulose, with larger size than PSA, mainly because aggregation of nanocellulose.

Causality Relationship between Crude Oil Variables and Budget Variables in Malaysia

OpenAIRE

Zakaria, Zukarnain; Shamsuddin, Sofian

2017-01-01

As an oil and gas exporter, Malaysia profited from higher world energy prices. However, the fall in oil prices from highs in 2014 significantly affected Malaysia’s government revenue (GR), hence its expenditure since the Malaysian GR still largely depends on oil revenues. Malaysia also has problems with high spending on energy subsidy, shrinking in its net crude oil export, and narrowing the gap between its crude oil production and consumption. Given this scenario, not only shocks in crude oi...

Volatility persistence in crude oil markets

International Nuclear Information System (INIS)

Charles, Amélie; Darné, Olivier

2014-01-01

Financial market participants and policy-makers can benefit from a better understanding of how shocks can affect volatility over time. This study assesses the impact of structural changes and outliers on volatility persistence of three crude oil markets – Brent, West Texas Intermediate (WTI) and Organization of Petroleum Exporting Countries (OPEC) – between January 2, 1985 and June 17, 2011. We identify outliers using a new semi-parametric test based on conditional heteroscedasticity models. These large shocks can be associated with particular event patterns, such as the invasion of Kuwait by Iraq, the Operation Desert Storm, the Operation Desert Fox, and the Global Financial Crisis as well as OPEC announcements on production reduction or US announcements on crude inventories. We show that outliers can bias (i) the estimates of the parameters of the equation governing volatility dynamics; (ii) the regularity and non-negativity conditions of GARCH-type models (GARCH, IGARCH, FIGARCH and HYGARCH); and (iii) the detection of structural breaks in volatility, and thus the estimation of the persistence of the volatility. Therefore, taking into account the outliers on the volatility modelling process may improve the understanding of volatility in crude oil markets. - Highlights: • We study the impact of outliers on volatility persistence of crude oil markets. • We identify outliers and patches of outliers due to specific events. • We show that outliers can bias (i) the estimates of the parameters of GARCH models, (ii) the regularity and non-negativity conditions of GARCH-type models, (iii) the detection of structural breaks in volatility of crude oil markets

Algal Production of Extra- and Intra-Cellular Polysaccharides as an Adaptive Response to the Toxin Crude Extract of Microcystis Aeruginosa

Directory of Open Access Journals (Sweden)

Mostafa Mohamed El-Sheekh

2012-11-01

Full Text Available This is an investigation concerned with studying the possible adaptive response of four different unicellular algae, Anabaena PCC 7120, Oscillatoria angustissima, Scendesmus obliquus and Chlorella vulgaris, to the toxin of Microcystis aeruginosa (Kützing. Theeffects of four different concentrations, 25, 50, 100 and 200 μg mL-1 of microcystins crude extract of M. aeruginosa, on both intra and extra-cellular polysaccharide levels, in log phase,of the four tested algae were studied. The obtained results showed differential increase in the production levels for both intra and extra-cellular polysaccharides by the tested algae,compared with the control. S. obliquus and C. vulgaris showed a resistance to crude toxinhigher than Anabaena PCC 7120 and O. angustissima. The highly production of polysaccharides by green algal species under this toxic stress indicated the involvement of these polysaccharides in protecting the algal cells against toxic species and, reflect thebiological behavior of particular algal species to the environmental stresses.

The ACEGES laboratory for energy policy: Exploring the production of crude oil

International Nuclear Information System (INIS)

Voudouris, Vlasios; Stasinopoulos, Dimitrios; Rigby, Robert; Di Maio, Carlo

2011-01-01

An agent-based computational laboratory for exploratory energy policy by means of controlled computational experiments is proposed. It is termed the ACEGES (agent-based computational economics of the global energy system). In particular, it is shown how agent-based modelling and simulation can be applied to understand better the challenging outlook for oil production by accounting for uncertainties in resource estimates, demand growth, production growth and peak/decline point. The approach emphasises the idea that the oil system is better modelled not as black-box abode of 'the invisible hand' but as a complex system whose macroscopic explananda emerges from the interactions of its constituent components. Given the estimated volumes of oil originally present before any extraction, simulations show that on average the world peak of crude oil production may happen in the broad vicinity of the time region between 2008 and 2027. Using the proposed petroleum market diversity, the market diversity weakness rapidly towards the peak year. - Highlights: → Development of oil scenarios using computational experiments. → Support of energy policy using agent-based modelling and simulation. → Demonstration of the agent-based computational economics of the global energy system (ACEGES) policy-support tool. → Energy policy by means of evidence-based forward-looking probabilistic forecasts.

Crude oil metabolites in groundwater at two spill sites

Science.gov (United States)

Bekins, Barbara A.; Cozzarelli, Isabelle M.; Erickson, Melinda L.; Steenson, Ross; Thorn, Kevin A.

2016-01-01

Two groundwater plumes in north central Minnesota with residual crude oil sources have 20 to 50 mg/L of nonvolatile dissolved organic carbon (NVDOC). These values are over 10 times higher than benzene and two to three times higher than Diesel Range Organics in the same wells. On the basis of previous work, most of the NVDOC consists of partial transformation products from the crude oil. Monitoring data from 1988 to 2015 at one of the sites located near Bemidji, MN show that the plume of metabolites is expanding toward a lakeshore located 335 m from the source zone. Other mass balance studies of the site have demonstrated that the plume expansion is driven by the combined effect of continued presence of the residual crude oil source and depletion of the electron accepting capacity of solid phase iron oxide and hydroxides on the aquifer sediments. These plumes of metabolites are not covered by regulatory monitoring and reporting requirements in Minnesota and other states. Yet, a review of toxicology studies indicates that polar metabolites of crude oil may pose a risk to aquatic and mammalian species. Together the results suggest that at sites where residual sources are present, monitoring of NVDOC may be warranted to evaluate the fates of plumes of hydrocarbon transformation products.

Successful phytoremediation of crude-oil contaminated soil at an oil exploration and production company by plants-bacterial synergism.

Science.gov (United States)

Fatima, Kaneez; Imran, Asma; Amin, Imran; Khan, Qaiser M; Afzal, Muhammad

2018-06-07

Phytoremediation is a promising approach for the cleanup of soil contaminated with petroleum hydrocarbons. This study aimed to develop plant-bacterial synergism for the successful remediation of crude oil-contaminated soil. A consortia of three endophytic bacteria was augmented to two grasses, Leptochloa fusca and Brachiaria mutica, grown in oil-contaminated soil (46.8 g oil kg -1 soil) in the vicinity of an oil exploration and production company. Endophytes augmentation improved plant growth, crude oil degradation, and soil health. Maximum oil degradation (80%) was achieved with B. mutica plants augmented with the endophytes and it was significantly (P oil reduction indicates that catabolic gene expression is important for hydrocarbon mineralization. This investigation showed that the use of endophytes with appropriate plant is an effective strategy for the cleanup of oil-contaminated soil under field conditions.

Wax deposition in crude oil pipelines

Energy Technology Data Exchange (ETDEWEB)

Assuncao, Pablo Morelato; Rodrigues, Lorennzo Marrochi Nolding [Universidade Federal do Espirito Santo, Sao Mateus, ES (Brazil). Centro Universitario Norte do Espirito Santo. Engenharia de Petroleo; Romero, Mao Ilich [University of Wyoming, Laramie, WY (United States). Enhanced Oil Recovery Institute], e-mail: mromerov@uwyo.edu

2010-07-01

Crude oil is a complex mixture of hydrocarbons which consists of aromatics, paraffins, naphthenics, resins asphaltenes, etc. When the temperature of crude oil is reduced, the heavy components, like paraffin, will precipitate and deposit on the pipe internal wall in the form of a wax-oil gel. The gel deposit consists of wax crystals that trap some amount of oil. As the temperature gets cooler, more wax will precipitate and the thickness of the wax gel will increase, causing gradual solidification of the crude and eventually the oil stop moving inside the offshore pipeline. Crude oil may not be able to be re-mobilized during re-startup. The effective diameter will be reduced with wax deposition, resulting in several problems, for example, higher pressure drop which means additional pumping energy costs, poor oil quality, use of chemical components like precipitation inhibitors or flowing facilitators, equipment failure, risk of leakage, clogging of the ducts and process equipment. Wax deposition problems can become so sever that the whole pipeline can be completely blocked. It would cost millions of dollars to remediate an offshore pipeline that is blocked by wax. Wax solubility decreases drastically with decreasing temperature. At low temperatures, as encountered in deep water production, is easy to wax precipitate. The highest temperature below which the paraffins begins to precipitate as wax crystals is defined as wax appearance temperature (WAT). Deposition process is a complex free surface problem involving thermodynamics, fluid dynamics, mass and heat transfer. In this work, a numerical analysis of wax deposition by molecular diffusion and shear dispersion mechanisms in crude oil pipeline is studied. Diffusion flux of wax toward the wall is estimated by Fick's law of diffusion, in similar way the shear dispersion; wax concentration gradient at the solid-liquid interface is obtained by the volume fraction conservation equation; and since the wax deposition

Heavy crude oils - From Geology to Upgrading - An Overview

International Nuclear Information System (INIS)

Huc, A.Y.

2010-01-01

Heavy oils, extra-heavy oils and tar sands are major players for the future of energy. They represent a massive world resource, at least the size of conventional oils. They are found all over the world but Canada and Venezuela together account, by themselves, for more than half of world deposits. They share the same origin as the lighter conventional oils, but their geological fate drove them into thick, viscous tar-like crude oils. Most of them result from alteration processes mediated by microbial degradation. They are characterized by a low content of lighter cuts and a high content of impurities such as sulfur and nitrogen compounds and metals; so, their production is difficult and deployment of specific processes is required in order to enhance their transportability and to upgrade them into valuable products meeting market needs, and honouring environmental requirements. Although these resources are increasingly becoming commercially producible, less than 1% of total heavy crude oil deposits worldwide are under active development. The voluntarily wide scope of this volume encompasses geology, production, transportation, upgrading, economics and environmental issues of heavy oils. It does not pretend to be exhaustive, but to provide an authoritative view of this very important energy resource. Besides presenting the current status of knowledge and technology involved in exploiting heavy oils, the purpose is to provide an insight into technical, economic and environmental challenges that should be taken up in order to increase the efficiency of production and processing, and finally to give a prospective view of the emerging technologies which will contribute to releasing the immense potential reserves of heavy oil and tar deposits. Contents: Part 1. Heavy Crude Oils.1. Heavy Crude Oils in the Perspective of World Oil Demand. 2. Definitions and Specificities. 3. Geological Origin of Heavy Crude Oils. 4. Properties and composition. Part 2. Reservoir Engineering

Utilization of microbial oil obtained from crude glycerol for the production of polyol and its subsequent conversion to polyurethane foams.

Science.gov (United States)

Uprety, Bijaya K; Reddy, Jayanth Venkatarama; Dalli, Sai Swaroop; Rakshit, Sudip K

2017-07-01

We have demonstrated possible use of microbial oil in biopolymer industries. Microbial oil was produced from biodiesel based crude glycerol and subsequently converted into polyol. Fermentation of crude glycerol in a batch bioreactor using Rhodosporidium toruloides ATCC 10788 produced 18.69g/L of lipid at the end of 7days. The microbial oil was then chemically converted to polyol and characterized using FT-IR and 1 H NMR. For comparison, canola oil and palm oil were also converted into their respective polyols. The hydroxyl numbers of polyols from canola, palm and microbial oil were found to be 266.86, 222.32 and 230.30 (mgKOH/g of sample) respectively. All the polyols were further converted into rigid and semi-rigid polyurethanes (maintaining the molar -NCO/-OH ratio of 1.1) to examine their suitability in polymer applications. Conversion of microbial lipid to polyurethane foam also provides a new route for the production of polymers using biodiesel based crude glycerol. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimization of a low-cost hyperosmotic medium and establishing the fermentation kinetics of erythritol production by Yarrowia lipolytica from crude glycerol.

Science.gov (United States)

Yang, Li-Bo; Zhan, Xiao-Bei; Zhu, Li; Gao, Min-Jie; Lin, Chi-Chung

2016-05-18

The production of erythritol by Yarrowia lipolytica from low-cost substitutable substrates for high yield was investigated. Crude glycerol, urea, and NaCl related to osmotic pressure were the most significant factors affecting erythritol production. An artificial neural network model and genetic algorithm were used to search the optimal composition of the significant factors and locate the resulting erythritol yield. Medium with 232.39 g/L crude glycerol, 1.57 g/L urea, and 31.03 g/L NaCl led to predictive maximum erythritol concentration of 110.7 g/L. The erythritol concentration improved from 50.4 g/L to 109.2 g/L with the optimized medium, which was reproducible. Erythritol fermentation kinetics were investigated in a batch system. Multistep fermentation kinetic models with hyperosmotic inhibitory effects were developed. The resulting mathematical equations provided a good description of temporal variations such as microbial growth (X), substrate consumption (S), and product formation (P) in erythritol fermentation. The accordingly derived model is the first reported model for fermentative erythritol production from glycerol, providing useful information to optimize the growth of Y. lipolytica and contributing visual description for the erythritol fermentation process under high osmotic pressure, as well as improvement of productivity and efficiency.

Import demand of crude oil and economic growth. Evidence from India

International Nuclear Information System (INIS)

Ghosh, Sajal

2009-01-01

This study establishes a long-run equilibrium relationship among quantity of crude oil import, income and price of the imported crude in India for the time span 1970-1971 to 2005-2006 using autoregressive distributed lag (ARDL) bounds testing approach of cointegration. Empirical results show that the long-term income elasticity of imported crude in India is 1.97 and there exists a unidirectional long-run causality running from economic growth to crude oil import. So reduction of crude oil import will not affect the future economic growth in India in the long-run. India should take various energy efficiency and demand side management measures in transport sector along with other measures like expanding and strengthening indigenous resource-base, substituting imported fuels by domestic fuels and de-controlling the price of petroleum products to reduce its import dependence. (author)

Characteristics of gas-liquid dynamics in operation of oil fields producing non-Newtonian crude oils

Energy Technology Data Exchange (ETDEWEB)

Mirzadzhanzade, A Kh; Khasaev, A M; Gurbanov, R S; Akhmedov, Z M

1968-08-01

Experimental studies have shown that crude oils from Azerbaidzhan, Uzbekistan, Tataria, Kazakhstan and other areas have anomalous properties under reservoir conditions. Such crude oils are non-Newtonian and (1) obey Darcys Law at low velocities; (2) obey an exponential law at higher velocities; and (3) obey a modified Darcys Law at most velocities. A discussion is given of (1) flow of non-Newtonian crude oils together with gas or water; (2) flow of non-Newtonian crude oils in well tubing; (3) behavior of wells producing non-Newtonian crude oils; and (4) pumping of non-Newtonian oils in wells. Experiments have shown that a visco-plastic liquid does not fill pump inlets completely; as the diameter of the pump inlet decreases so also does the degree of liquid filling. A statistical analysis of production data from 160 fields with Newtonian oil and 129 fields with non- Newtonian oil has shown that much higher production is obtained from fields with Newtonian crude oils.

Dextransucrase production using cashew apple juice as substrate: effect of phosphate and yeast extract addition.

Science.gov (United States)

Chagas, Clarice M A; Honorato, Talita L; Pinto, Gustavo A S; Maia, Geraldo A; Rodrigues, Sueli

2007-05-01

Cashew apples are considered agriculture excess in the Brazilian Northeast because cashew trees are cultivated primarily with the aim of cashew nut production. In this work, the use of cashew apple juice as a substrate for Leuconostoc mesenteroides cultivation was investigated. The effect of yeast extract and phosphate addition was evaluated using factorial planning tools. Both phosphate and yeast extract addition were significant factors for biomass growth, but had no significant effect on maximum enzyme activity. The enzyme activities found in cashew apple juice assays were at least 3.5 times higher than the activity found in the synthetic medium. Assays with pH control (pH = 6.5) were also carried out. The pH-controlled fermentation enhanced biomass growth, but decreased the enzyme activity. Crude enzyme free of cells produced using cashew apple juice was stable for 16 h at 30 degrees C at a pH of 5.0.

Bioconversion of crude glycerol feedstocks into ethanol by Pachysolen tannophilus

DEFF Research Database (Denmark)

Liu, Xiaoying; Jensen, Peter Ruhdal; Workman, Mhairi

2012-01-01

Glycerol, the by-product of biodiesel production, is considered as a waste by biodiesel producers. This study demonstrated the potential of utilising the glycerol surplus through conversion to ethanol by the yeast Pachysolen tannophilus (CBS4044). This study demonstrates a robust bioprocess which...... was not sensitive to the batch variability in crude glycerol dependent on raw materials used for biodiesel production. The oxygen transfer rate (OTR) was a key factor for ethanol production, with lower OTR having a positive effect on ethanol production. The highest ethanol production was 17.5 g/L on 5% (v/v) crude...... glycerol, corresponding to 56% of the theoretical yield. A staged batch process achieved 28.1 g/L ethanol, the maximum achieved so far for conversion of glycerol to ethanol in a microbial bioprocess. The fermentation physiology has been investigated as a means to designing a competitive bioethanol...

Study on the hydrodeoxygenative upgrading of crude bio-oil produced from woody biomass by fast pyrolysis

International Nuclear Information System (INIS)

Kim, Tae-Seung; Oh, Shinyoung; Kim, Jae-Young; Choi, In-Gyu; Choi, Joon Weon

2014-01-01

Crude bio-oil produced from fast pyrolysis of yellow poplar wood was subjected to HDO (hydrodeoxygenation) for the purpose of reducing water content as well as increasing heating value. HDO was performed in an autoclave reactor at three different reaction factors: temperature (250–370 °C), reaction time (40–120 min), and Pd/C catalyst loading (0–6 wt%) under hydrogen atmosphere. After completion of HDO, gas, char, and two immiscible liquid products (light oil and heavy oil) were obtained. Liquid products were less acidic and contained less water than crude bio-oil. Water content of heavy oil was ranged between 0.4 wt% and 1.9 wt%. Heating values of heavy oil were estimated between 28.7 and 37.4 MJ/kg, which was about twice higher than that of crude bio-oil. Elemental analysis revealed that heavy oil had a lower O/C ratio (0.17–0.36) than crude bio-oil (0.71). H/C ratio of heavy oil decreased from 1.50 to 1.32 with an increase of temperature from 250 °C to 350 °C, respectively. - Highlights: • Bio-oil was subjected to hydrodeoxygenation with Pd/C catalyst in supercritical ethanol. • Gas, char and two immiscible liquids (light/heavy oil) were obtained as final products. • Ethanol addition reduced the char formation during hydrodeoxygenation. • The heavy oil was characteristic to less acidic and less water content than bio-oil. • Higher heating value of the heavy oil was measured to 28.7–37.4 MJ/kg

Exploration and production of crude oil and natural gas in Germany in 2012

International Nuclear Information System (INIS)

Pasternak, Michael

2013-01-01

This article presents an overview of oil and gas exploration and production in Germany in 2012. The report is based on data gathered on a regular basis by the State Authority for Mining, Energy and Geology (LBEG) from the oil and gas companies and the other state mining offices. Due to the granting of new licences in the last years, a significant increase of geophysical prospecting of the subsurface for oil and gas deposits was observed. Six 3D seismic surveys were conducted. Five surveys were located in the Upper Rhine Valley and one in the lowlands of Northwest Germany. 2D seismic data were acquired in Lusatia (Brandenburg) and at the coast of the Baltic Sea. The number of exploration wells decreased once again. In 2012 nine exploration wells were drilled, compared to ten in the previous year. In addition to that number, another seven exploration wells were drilled to total depth already before 2012, but not completed by final well results in 2012. None of the ten new field wildcats were completed by result. Three exploration wells (appraisal wells) were completed successfully. Two of these wells confirmed the presence of gas and one the presence of oil. The number of development wells decreased significantly. In 2012 31 wells were drilled, compared to 46 in the prominent year 2011. Another 13 wells were drilled to total depth already before 2012, but not completed by final well results in 2012. 31 wells were completed successfully. 30 of these wells encountered oil or gas pay zones. In 2011 drilling meterage has reached its highest value since 1998. In contrast the total drilling meterage decreased slightly by less than 2000 m to 71,424 min 2012. The natural gas production continued its downward trend. Due to the depletion of gas fields, the annual natural gas production dropped by 9.1% compared to the previous year and amounted to 11.7 billion m 3 (field quality). After the increase in 2011, the annual crude oil production decreased by 2.1% to 2.6 million t

Leadership Strategies for Maintaining Profitability in a Volatile Crude Oil Market

Science.gov (United States)

Braimoh, Lucky Anderson

Volatile crude oil prices significantly affect the profitability of crude oil firms. The purpose of this single case study was to explore strategies some crude oil and gas business leaders used to remain profitable during periods of crude oil price volatility. The target population comprised 8 crude oil and gas business leaders located in Calgary, Canada, whose company remained profitable despite crude oil price volatility. The transformational leadership theory formed the conceptual framework for the study. Data were collected through the use of semistructured face-to-face interviews, company reports, and field notes. Data analysis involved a modified Van Kamm method, which included descriptive coding, a sequential review of the interview transcripts, and member checking. Based on methodological triangulation and thematic analysis, 5 themes emerged from the study, including communication and engagement; motivation and empowerment; measurement, monitoring, and control; self-awareness and humility; and efficiency and optimization. The implications for social change include the potential for crude oil and gas companies in Calgary, Canada to manage production costs, ensure earnings and profitability, and thus improve the socioeconomic well-being of Calgary indigenes through improved employment opportunities.

An analysis of price and volatility transmission in butter, palm oil and crude oil markets

Directory of Open Access Journals (Sweden)

Dennis Bergmann

2016-11-01

Full Text Available Abstract Recent changes to the common agricultural policy (CAP saw a shift to greater market orientation for the EU dairy industry. Given this reorientation, the volatility of EU dairy commodity prices has sharply increased, creating the need to develop proper risk management tools to protect farmers’ income and to ensure stable prices for processors and consumers. In addition, there is a perceived threat that these commodities may be replaced by cheaper substitutes, such as palm oil, as dairy commodity prices become more volatile. Global production of palm oil almost doubled over the last decade while butter production remained relatively flat. Palm oil also serves as a feedstock for biodiesel production, thus establishing a new link between agricultural commodities and crude oil. Price and volatility transmission effects between EU and World butter prices, as well as between butter, palm oil and crude oil prices, before and after the Luxembourg agreement, are analysed. Vector autoregression (VAR models are applied to capture price transmission effects between these markets. These are combined with a multivariate GARCH model to account for potential volatility transmission. Results indicate strong price and volatility transmission effects between EU and World butter prices. EU butter shocks further spillover to palm oil volatility. In addition, there is evidence that oil prices spillover to World butter prices and World butter volatility.

Seahorse (Hippocampus reidi) as a bioindicator of crude oil exposure.

Science.gov (United States)

Delunardo, Frederico Augusto Cariello; de Carvalho, Luciano Rodrigues; da Silva, Bruno Ferreira; Galão, Michel; Val, Adalberto Luís; Chippari-Gomes, Adriana R

2015-07-01

This study explored the suitability of the seahorse Hippocampus reidi (Ginsburg, 1933) for assessing biomarkers of genotoxic effects and its use as a sentinel organism to detect the effects of acute exposure to petroleum hydrocarbons. Fish were exposed to three concentrations of crude oil (10, 20 and 30 g/kg) for 96 h, and the activity of phase II biotransformation enzyme glutathione S-transferase (GST) was measured. In addition, we performed genotoxicity assays, such as comet assay, micronucleus (MN) test and nuclear abnormalities (NA) induction, on the erythrocytes of the fish species. Our results revealed that the inhibition of hepatic GST activity in H. reidi was dependent on increasing crude oil concentrations. In contrast, an increase in the damage index (DI) and MN frequency were observed with increased crude oil concentrations. These results indicate that the alkaline comet assay and micronucleus test were suitable and useful in the evaluation of the genotoxicity of crude oil, which could improve determinations of the impact of oil spills on fish populations. In addition, H. reidi is a promising "sentinel organism" to detect the genotoxic impact of petroleum hydrocarbons. Copyright © 2015 Elsevier Inc. All rights reserved.

Mitigation of the inhibitory effect of soap by magnesium salt treatment of crude glycerol--a novel approach for enhanced biohydrogen production from the biodiesel industry waste.

Science.gov (United States)

Sarma, Saurabh Jyoti; Brar, Satinder Kaur; Le Bihan, Yann; Buelna, Gerardo; Soccol, Carlos Ricardo

2014-01-01

Owing to its inhibitory effect on microbial growth, soap present in crude glycerol (CG) is a concern in biological valorization of the biodiesel manufacturing waste. By salting out strategy, up to 42% of the soap has been removed and the approach has beneficial effect on H2 production; however, removal of more than 7% of the soap was found to be inhibitory. Actually, soap is utilized as a co-substrate and due to removal; the carbon-nitrogen ratio of the medium might have decreased to reduce the production. Alternatively, without changing the carbon-nitrogen ratio of CG, MgSO4 treatment can convert the soap to its inactive form (scum). The approach was found to increase the H2 production rate (33.82%), cumulative H2 production (34.70%) as well as glycerol utilization (nearly 2.5-folds). Additionally, the treatment can increase the Mg (a nutrient) content of the medium from 0.57 ppm to 201.92 ppm. Copyright © 2013 Elsevier Ltd. All rights reserved.

The strategic and economic value of exploiting heavy crude

International Nuclear Information System (INIS)

Saniere, A.

2003-01-01

Non-conventional oil, and particularly heavy crude varieties, will play an increasingly important role in meeting growing global energy requirements by 2030 and beyond. These heavy oils currently account for high volumes in certain areas but their proportion of global oil production remains modest for the moment, This should significantly change with the completion of several projects currently underway in Canada and Venezuela. Indeed, the technological innovations occurring over recent years have allowed for a considerable reduction in exploitation costs for these crude varieties and improved economic profitability conditions for the projects. The geographical location of resources (which are independent of the Middle East) and the fact that they are not subject to OPEC quotas also make these crude varieties particularly attractive. (authors)

Bioremediation Potential of Native Hydrocarbons Degrading Bacteria in Crude Oil Polluted Soil

Directory of Open Access Journals (Sweden)

Mariana MARINESCU

2017-05-01

Full Text Available Bioremediation of crude oil contaminated soil is an effective process to clean petroleum pollutants from the environment. Crude oil bioremediation of soils is limited by the bacteria activity in degrading the spills hydrocarbons. Native crude oil degrading bacteria were isolated from different crude oil polluted soils. The isolated bacteria belong to the genera Pseudomonas, Mycobacterium, Arthrobacter and Bacillus. A natural biodegradable product and bacterial inoculum were used for total petroleum hydrocarbon (TPH removal from an artificial polluted soil. For soil polluted with 5% crude oil, the bacterial top, including those placed in the soil by inoculation was 30 days after impact, respectively 7 days after inoculum application, while in soil polluted with 10% crude oil,  multiplication top of bacteria was observed in the determination made at 45 days after impact and 21 days after inoculum application, showing once again how necessary is for microorganisms habituation and adaptation to environment being a function of pollutant concentration. The microorganisms inoculated showed a slight adaptability in soil polluted with 5% crude oil, but complete inhibition in the first 30 days of experiment at 10% crude oil.

Cracking of crude oil in the molten metals

Directory of Open Access Journals (Sweden)

Marat A. Glikin

2014-03-01

Full Text Available In this paper is investigated the process of crude oil and its individual fractions cracking in the molten metals medium to produce light petroleum products. Thermodynamic calculations demonstrate the possibility of using lead and tin including alloys thereof as the melt. The cracking of West Siberian crude oil is studied at temperatures 400-600 °C. It is detected that as the temperature increases there is increase of aromatic hydrocarbons and olefins content in gasoline while naphthenes, n- and i-paraffins content reduces. Optimal temperature for cracking in molten metals is ~500 °C. The use of a submerged nozzle increases the yield of light petroleum products by ~2%. The research octane number of gasoline produced is 82-87 points. It is determined that the yield of light petroleum products depending on the experimental conditions is increased from 46.9 to 55.1-61.3% wt.   

Open-source LCA tool for estimating greenhouse gas emissions from crude oil production using field characteristics.

Science.gov (United States)

El-Houjeiri, Hassan M; Brandt, Adam R; Duffy, James E

2013-06-04

Existing transportation fuel cycle emissions models are either general and calculate nonspecific values of greenhouse gas (GHG) emissions from crude oil production, or are not available for public review and auditing. We have developed the Oil Production Greenhouse Gas Emissions Estimator (OPGEE) to provide open-source, transparent, rigorous GHG assessments for use in scientific assessment, regulatory processes, and analysis of GHG mitigation options by producers. OPGEE uses petroleum engineering fundamentals to model emissions from oil and gas production operations. We introduce OPGEE and explain the methods and assumptions used in its construction. We run OPGEE on a small set of fictional oil fields and explore model sensitivity to selected input parameters. Results show that upstream emissions from petroleum production operations can vary from 3 gCO2/MJ to over 30 gCO2/MJ using realistic ranges of input parameters. Significant drivers of emissions variation are steam injection rates, water handling requirements, and rates of flaring of associated gas.

Effect of Crude Oil Price on Agricultural Productivity in Nigeria (1981 ...

African Journals Online (AJOL)

SH

Faculty of Agricultural Sciences, LAUTECH, Ogbomoso, Nigeria, 2013. Effect of Crude Oil ... foreign exchange earnings since early. 1970s. ..... has been an improvement in the devaluation of the currency in .... IMF papers, Vol. 27:637 – 677.

Socio–economic and environmental impact of crude oil exploration ...

African Journals Online (AJOL)

Socio–economic and environmental impact of crude oil exploration and production on agricultural production: a case study of Edjeba and Kokori communities in Delta State of ... The results also showed an increase in the occurrence of health hazard, air/noise pollution and heightened deforestation in these communities.

A catalogue of crude oil and oil product properties, 1990

International Nuclear Information System (INIS)

Bobra, M.A.; Callaghan, S.

1990-09-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 109 refs

A catalogue of crude oil and oil product properties, 1992

International Nuclear Information System (INIS)

Whiticar, S.; Bobra, M.; Liuzzo, P.; Callaghan, S.; Fingas, M.; Jokuty, P.; Ackerman, F.; Cao, J.

1993-02-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 140 refs

Conversion of Crude Glycerol to 1, 3-Propanediol by Newly Isolated Kluyvera Cryocrescens

International Nuclear Information System (INIS)

Loh, S.K.; Stasha Eleanor Rosland Abel

2016-01-01

Bio diesel, an environmental-friendly and renewable fuel, has gained market share and popularity as an alternative to fossil fuel. While expanding its production globally to meet the demand, the production of its principal co-product, crude glycerol which is surplus and under utilised, has affected both the economic and environment. Crude glycerol has limited usage due to the impurities present. It cannot be disposed naturally in the environment and its storage and processing are very costly. Glycerol with its triglyceride backbone serves as a natural metabolite susceptible to microbial degradation into high value-added compounds. In this study, a novel 1,3-PD producing bacterial strain isolated from palm oil mill effluent was used in microbial fermentation of crude glycerol. The strain, identified as Kluyvera cryocrescens NBRC 102467 based on its 16S ribosomal ribonucleic acid sequences, was capable of producing 1,3-PD (5.28 g litre -1 ) along with by-products, butanol (0.34 g litre -1 ) and acetone (0.31 g litre -1 ) after an optimum 48 hour of incubation at 30 degree Celsius in agitated medium enriched with crude glycerol at 150 revolutions per minute. Interestingly, its productivity peaked at the 6 hour reaching 0.28 g litre -1 hour -1 and declined thereafter. In future, this strain has potential to be used in the bioprocess of interest. (author)

Environmental Drivers of Differences in Microbial Community Structure in Crude Oil Reservoirs across a Methanogenic Gradient

OpenAIRE

Shelton, Jenna L.; Akob, Denise M.; McIntosh, Jennifer C.; Fierer, Noah; Spear, John R.; Warwick, Peter D.; McCray, John E.

2016-01-01

Stimulating in situ microbial communities in oil reservoirs to produce natural gas is a potentially viable strategy for recovering additional fossil fuel resources following traditional recovery operations. Little is known about what geochemical parameters drive microbial population dynamics in biodegraded, methanogenic oil reservoirs. We investigated if microbial community structure was significantly impacted by the extent of crude oil biodegradation, extent of biogenic methane production, a...

Distribution and quantitative assessment of world crude oil reserves and resources

Science.gov (United States)

Masters, Charles D.; Root, David H.; Dietzman, William D.

1983-01-01

World Demonstrated Reserves of crude oil are approximately 723 billion barrels of oil (BBO). Cumulative production is 445 BBO and annual production is 20 BBO. Demonstrated Reserves of crude-oil have declined over the past 10 years consistent with discoveries lagging production over the same period. The assessment of Undiscovered Resources shows a 90 percent probability that the amount discoverable lies between 321 and 1,417 BBO, 550 BBO being the most likely value. The most likely value for Ultimate recoverable resources is 1,718 BBO. The distribution of Ultimate Resources of crude oil will remain highly skewed toward the Middle East; no frontier areas that have potentials large enough to significantly affect present distribution are recognized. Rates of discovery have continued to decline over the past 20 years even though exploration activity has increased in recent years. Prudence dictates, therefore, that the low side of the assessment of Undiscovered Resources be responsibly considered and that alternate energy sources be a part of future planning. Extra-heavy oil and bitumen are assessed separately, with Reserves being figured as the annual productive capacity of installed facilities times 25 years. The annual production of extra-heavy oil is about 8 million barrels and of bitumen about 60 million barrels.

Biodiesel production from lipids in wet microalgae with microwave irradiation and bio-crude production from algal residue through hydrothermal liquefaction.

Science.gov (United States)

Cheng, Jun; Huang, Rui; Yu, Tao; Li, Tao; Zhou, Junhu; Cen, Kefa

2014-01-01

A cogeneration process of biodiesel and bio-crude was proposed to make full use of wet microalgae biomass. High-grade biodiesel was first produced from lipids in wet microalgae through extraction and transesterification with microwave irradiation. Then, low-grade bio-crude was produced from proteins and carbohydrates in the algal residue through hydrothermal liquefaction. The total yield (40.19%) and the total energy recovery (67.73%) of the cogenerated biodiesel and bio-crude were almost equal to those of the bio-oil obtained from raw microalgae through direct hydrothermal liquefaction. Upon microwave irradiation, proteins were partially hydrolyzed and the hydrolysates were apt for deaminization under the hydrothermal condition of the algal residue. Hence, the total remaining nitrogen (16.02%) in the cogenerated biodiesel and bio-crude was lower than that (27.06%) in the bio-oil. The cogeneration process prevented lipids and proteins from reacting to produce low-grade amides and other long-chain nitrogen compounds during the direct hydrothermal liquefaction of microalgae. Copyright © 2013 Elsevier Ltd. All rights reserved.

Perspective for using Nd-Fe-B magnets as a tool for the improvement of the production and transportation of Vietnamese crude oil with high paraffin content

International Nuclear Information System (INIS)

Tung, N.P.; Vinh, N.Q.; Phong, N.T.P.; Long, B.Q.K.; Hung, P.V.

2003-01-01

Controlling the paraffin deposition is one of the most serious and costly problems for high-paraffin crude-oil production and transportation. This holds especially for offshore, deep-water wells and pipelines, like in Vietnam. For finding solutions for these problems, a series of experiments has been performed in order to study the effects of a magnetic field on the rheology of two often produced crude oil samples, using the high and variable magnetic-flux density of a Nd-Fe-B magnet. The resulting changes in the essential characteristics of the magnetically treated (MT) crude oils, like form and size of the paraffin clusters as well as the rheology parameters, have definitely proved the possibility to use a Nd-Fe-B magnetic tool as an environmentally friendly and effective method to control the paraffin deposition in crude oils of Vietnam that have a high paraffin content

Procedures in field systems for collecting and demulsifying crude oils

Energy Technology Data Exchange (ETDEWEB)

Vakhitov, G G; Graifer, V I; Tronov, V P; Zakirov, I G

1969-01-01

This microscopic study of crude oil emulsification and demulsification showed that the sooner an emulsion is chemically treated, the less its stability. This finding led to the practice of adding demulsifiers to the crude oil in pipelines. This method of demulsification is now used in Romashkino, Bablinsk, and Elkhovs fields. By this early addition of a chemical, the tendency of the pipeline to form stable, highly viscous emulsions is reduced. This treatment also facilitates separation of water from oil in storage tanks. Repeated tests have shown that pipeline demulsification is a highly effective and economic process. This method reduces crude oil dewatering costs by several hundred percent.

Modeling of well drilling heating on crude oil using microwave

Energy Technology Data Exchange (ETDEWEB)

Muntini, Melania Suweni, E-mail: melania@physics.its.ac.id; Pramono, Yono Hadi; Yustiana [Physics Department, Institut Teknologi Sepuluh Nopember, Surabaya Kampus ITS, Sukolilo, Surabaya 60111 (Indonesia)

2016-03-11

As the world’s oil reserves are dwindling, some researchers have been prompted to make a breakthrough to further improve the efficiency of exploration and production. One of the technologies used is heating the crude oil. This paper presents the modeling results of heat treatment on crude oil using microwave energy. Modeling is conducted by assuming that the diameter of the well is 11,16 cm, the heat source is applied on the surface of the well, and the cut-off frequency in the air and on crude oil are 1,56 GHz. and 0.91 GHz, respectively. The energy generated by the microwave radiation is converted into heat energy which is absorbed by the crude oil. Consequently, this energy increases the temperature of crude oil through a heat transfer mechanism. The results obtained showed that the temperature of crude oil is about 200°C at a depth of 62.5cm, and at a distance of 3 cm from the center of the well. Temperature along the well follows an exponential function, which is from the center of the well in the direction radially outward from the cylinder axis. It has been observed that the temperature decreases as measured from the well surface along the cylinder.

Imported resources - oil crude oil processing in the Czech Republic and its prospectives

Energy Technology Data Exchange (ETDEWEB)

Soucek, I.; Ottis, I. [Kaucuk, Kralupy nad Vitavou (Czechoslovakia)

1995-12-01

This paper examines the availability of various crude oils, addressing specifically crude oil pipelines to the Czech Republic, both existing and under construction. Secondly, the economic status of two main Czech refineries is examined in comparison to international trends, technical configurations, and product supply and demand.

The Use of Biobased Surfactant Obtained by Enzymatic Syntheses for Wax Deposition Inhibition and Drag Reduction in Crude Oil Pipelines

Directory of Open Access Journals (Sweden)

Zhihua Wang

2016-04-01

Full Text Available Crude oil plays an important role in providing the energy supply of the world, and pipelines have long been recognized as the safest and most efficient means of transporting oil and its products. However, the transportation process also faces the challenges of asphaltene-paraffin structural interactions, pipeline pressure losses and energy consumption. In order to determine the role of drag-reducing surfactant additives in the transportation of crude oils, experiments of wax deposition inhibition and drag reduction of different oil in pipelines with a biobased surfactant obtained by enzymatic syntheses were carried out. The results indicated that heavy oil transportation in the pipeline is remarkably enhanced by creating stable oil-in-water (O/W emulsion with the surfactant additive. The wax appearance temperature (WAT and pour point were modified, and the formation of a space-filling network of interlocking wax crystals was prevented at low temperature by adding a small concentration of the surfactant additive. A maximum viscosity reduction of 70% and a drag reduction of 40% for light crude oil flows in pipelines were obtained with the surfactant additive at a concentration of 100 mg/L. Furthermore, a successful field application of the drag-reducing surfactant in a light crude oil pipeline in Daqing Oilfield was demonstrated. Hence, the use of biobased surfactant obtained by enzymatic syntheses in oil transportation is a potential method to address the current challenges, which could result in a significant energy savings and a considerable reduction of the operating cost.

Compositional modification of crude oil during oil recovery

Energy Technology Data Exchange (ETDEWEB)

Zhu, Yangming; Weng, Huanxin [Department of Earth Sciences, Zhejiang University, Hangzhou 310027 (China); Chen, Zulin; Chen, Qi [Petroleum Geochemistry Research Center, Jianghan Petroleum University, Jingzhou, Hubei (China)

2003-05-01

Ten crude oils from two recovery stages spanning 5-10-year interval of five productive wells in the Tarim Basin, northwest China were analyzed for their compositional modification during production process. Significant compositional changes in polar and nonpolar fractions between the previous oil samples and the latter ones were noted at both bulk and molecular level. The latter oil samples appear to contain more aromatic fraction and less asphaltenes and resin, and their gas chromatography (GC) data for whole oil show reduced alkanes with low molecular weight and enhanced high homologue relative to the previous oil samples. Compared with the oils collected from the previous recovery stage, the concentration of basic type of nitrogen-containing compounds and organic acids in oils from the latter recovery stage have a reducing trend, suggesting the occurrence of interaction between crude oil and reservoir rock.

Effects of dietary inclusion of high concentrations of crude glycerin on meat quality and fatty acid profile of feedlot fed Nellore bulls.

Directory of Open Access Journals (Sweden)

Eric H C B van Cleef

Full Text Available Crude glycerin, the main by-product of biodiesel production, can replace dietary energy sources, such as corn. The objective of this study was to evaluate the inclusion of up to 30% of crude glycerin in dry matter (DM of the total diets, and its effects on meat quality parameters of feedlot Nellore bulls. Thirty animals (227.7 ± 23.8 kg body weight; 18 months old were housed in individual pens and fed 5 experimental diets, containing 0, 7.5, 15, 22.5 or 30% crude glycerin (DM basis. After 103 d (21 d adaptation animals were slaughtered and the Longissimus muscle was collected. The characteristics assessed were chemical composition, fatty acid profile, cholesterol, shear force, pH, color, water-holding capacity, cooking loss and sensory properties. The increasing inclusion of crude glycerin in the diets did not affect the chemical composition of the Longissimus muscle (P > 0.10. A quadratic effect was observed when levels of crude glycerin were increased, on the concentration of pentadecanoic, palmitoleic and eicosenoic fatty acids in meat (P < 0.05, and on the activity of the delta-9 desaturase 16 and delta-9 desaturase 18 enzymes (P < 0.05. The addition of crude glycerin increased the gamma linolenic fatty acid concentration (P < 0.01, and altered the monounsaturated fatty acids in Longissimus muscle of animals (Pquad. < 0.05. Crude glycerin decreased cholesterol content in meat (P < 0.05, and promoted higher flavor score and greasy intensity perception of the meat (P < 0.01. The inclusion of up to 30% crude glycerin in Nellore cattle bulls`diets (DM basis improves meat cholesterol and sensory attributes, such as flavor, without affecting significantly the physical traits, the main fatty acid concentrations and the chemical composition.

Impact of impurities in biodiesel-derived crude glycerol on the fermentation by Clostridium pasteurianum ATCC 6013

Energy Technology Data Exchange (ETDEWEB)

Venkataramanan, Keerthi P.; Boatman, Judy J.; Taconi, Katherine A. [Alabama Univ., Huntsville, AL (United States). Dept. of Chemical and Materials Engineering; Kurniawan, Yogi; Bothun, Geoffrey D. [Rhode Island Univ., Kingston, RI (United States). Dept. of Chemical Engineering; Scholz, Carmen [Alabama Univ., Huntsville, AL (United States). Dept. of Chemistry

2012-02-15

During the production of biodiesel, crude glycerol is produced as a byproduct at 10% (w/w). Clostridium pasteurianum has the inherent potential to grow on glycerol and produce 1,3-propanediol and butanol as the major products. Growth and product yields on crude glycerol were reported to be slower and lower, respectively, in comparison to the results obtained from pure glycerol. In this study, we analyzed the effect of each impurity present in the biodiesel-derived crude glycerol on the growth and metabolism of glycerol by C. pasteurianum. The crude glycerol contains methanol, salts (in the form of potassium chloride or sulfate), and fatty acids that were not transesterified. Salt and methanol were found to have no negative effects on the growth and metabolism of the bacteria on glycerol. The fatty acid with a higher degree of unsaturation, linoleic acid, was found to have strong inhibitory effect on the utilization of glycerol by the bacteria. The fatty acid with lower or no degrees of unsaturation such as stearic and oleic acid were found to be less detrimental to substrate utilization. The removal of fatty acids from crude glycerol by acid precipitation resulted in a fermentation behavior that is comparable to the one on pure glycerol. These results show that the fatty acids in the crude glycerol have a negative effect by directly affecting the utilization of glycerol as the carbon source, and hence their removal from crude glycerol is an essential step towards the utilization of crude glycerol. (orig.)

Implications of lifting the ban on the export of Alaskan crude oil

Energy Technology Data Exchange (ETDEWEB)

1990-03-26

Present legislation effectively bans the export of crude oil produced in the United States. The ban has been in effect for years and is particularly stringent with respect to crude oil produced in Alaska, particularly on the North Slope. The Alaska crude export ban is specifically provided for in the Trans-Alaska Pipeline Authorization Act of 1973 and in other legislation. It was imposed for two reasons. The first was to reduce US dependence on imported crude oil. The Arab oil embargo had been imposed shortly before the Act was passed and a greater measure of energy independence was considered imperative at that time. The second reason was to assure that funds expended in building an Alaskan pipeline would benefit domestic users rather than simply employed to facilitate shipments to other countries. The main objective of this report is to estimate the potential impacts on crude oil prices that would result from lifting the export ban Alaskan crude oil. The report focuses on the Japanese market and the US West Coast market. Japan is the principal potential export market for Alaskan crude oil. Exports to that market would also affect the price of Alaskan crude oil as well as crude oil and product prices on the West Coast and the volume of petroleum imported in that area. 3 figs., 8 tabs.

Monitoring the process of purification of crude glycerol derived from biodiesel production: a method based on fluorescence spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Magalhaes, Keurison F.; Caires, Anderson R.L. [Universidade Federal da Grande Dourados, MS (Brazil). Grupo de Optica Aplicada; Oliveira, Samuel L. [Universidade Federal de Mato Grosso do Sul (UFMS), MS (Brazil). Grupo de Optica e Fotonica

2011-07-01

Full text. The use of biodiesel has increased worldwide. The biodiesel production on an industrial scale has been based on the transesterification of vegetable oils and fats with methanol in the presence of an alkaline catalyst. During the transesterification, one molecule of triglyceride reacts with three molecules of alcohol to produce glycerol and molecules of alkyl esters (biodiesel). As a result, an increase in biodiesel production also enhances the availability of glycerol on the market. However, crude glycerin has about 30% of impurities which are inherent to biodiesel production such as catalyst, alcohol and fatty acids. The present study evaluated the usefulness of the fluorescence spectroscopy as a tool to monitor the glycerol purification process. Glycerol samples were obtained from transesterification of soybean, canola, and sunflower oils in the presence of NaOH. After stirring time, the solutions were let to stand in separating funnels, then two phases were observed: one containing mainly biodiesel and other consisting of glycol. Then, the respective glycerol samples were collected, henceforth called G1. After that, it was added H2SO4 (20%) in the crude glycerol samples to reduce their pH to 4 in order to remove fatty acids. The solutions were stored for 24 hours in separating funnels. The glycerol (heavy phase), hereafter named G2, was then separated and filtered. To remove other impurities from G2 samples by means of ionic exchange columns, the samples were neutralized and diluted using Milli-Q water (G3 samples). Aliquots of 20 mL were then passed through cationic and anionic resins (G4 and G5 samples, respectively). Emission and excitation spectra of the G1-G5 samples as well as of the glycerol PA-ACS (reference) were recorded at room temperature using a spectrofluorimeter. The emission spectra were obtained setting the excitation at 325nm and monitoring the emission in the 330-800nm range. Fluorimetric maps were also achieved by pumping the

Anaerobic co-digestion of swine manure and crude glycerol derived from animal fat - Effect of hydraulic retention time

DEFF Research Database (Denmark)

Lymperatou, Anna; Skiadas, Ioannis V.; Gavala, Hariklia N.

2018-01-01

Crude glycerol (CG), an abundant by-product of bio-diesel production, has been identified as a suitable co-substrate for improving the biogas production of livestock manure through anaerobic digestion (AD). In this study, the potential of utilizing CG generated from the esterification of animal......, biochemical methane potential tests indicated that the addition of 1% w/w CG to swine manure-AD is more efficient in terms of percent of theoretical amount of methane obtained than the addition of 3% w/w. However, in continuous experiments, co-digestion of manure with 3% w/w CG did not exhibit any sign...... fats for biogas production was studied in both batch and continuous AD experiments, with emphasis on the importance of the hydraulic retention time (HRT). Batch experiments showed that the limiting step in the methane production rate during CG mono-digestion was the 1,3-propanediol uptake. Additionally...

Refining of crude uranium by solvent extraction for production of nuclear pure uranium metal

International Nuclear Information System (INIS)

Gupta, S.K.; Manna, S.; Singha, M.; Hareendran, K.N.; Chowdhury, S.; Satpati, S.K.; Kumar, K.

2007-01-01

Uranium is the primary fuel material for any nuclear fission energy program. Natural uranium contains only 0.712% of 235 U as fissile constituent. This low concentration of fissile isotope in natural uranium calls for a very high level of purity, especially with respect to neutron poisons like B, Cd, Gd etc. before it can be used as nuclear fuel. Solvent extraction is a widely used technique by which crude uranium is purified for reactor use. Uranium metal plant (UMP), BARC, Trombay is engaged in refining of uranium concentrate for production of nuclear pure uranium metal for fabrication of fuel for research reactors. This paper reviews some of the fundamental aspects of this refining process with some special references to UMP, BARC. (author)

Effects of different remediation treatments on crude oil contaminated saline soil.

Science.gov (United States)

Gao, Yong-Chao; Guo, Shu-Hai; Wang, Jia-Ning; Li, Dan; Wang, Hui; Zeng, De-Hui

2014-12-01

Remediation of the petroleum contaminated soil is essential to maintain the sustainable development of soil ecosystem. Bioremediation using microorganisms and plants is a promising method for the degradation of crude oil contaminants. The effects of different remediation treatments, including nitrogen addition, Suaeda salsa planting, and arbuscular mycorrhiza (AM) fungi inoculation individually or combined, on crude oil contaminated saline soil were assessed using a microcosm experiment. The results showed that different remediation treatments significantly affected the physicochemical properties, oil contaminant degradation and bacterial community structure of the oil contaminated saline soil. Nitrogen addition stimulated the degradation of total petroleum hydrocarbon significantly at the initial 30d of remediation. Coupling of different remediation techniques was more effective in degrading crude oil contaminants. Applications of nitrogen, AM fungi and their combination enhanced the phytoremediation efficiency of S. salsa significantly. The main bacterial community composition in the crude oil contaminated saline soil shifted with the remediation processes. γ-Proteobacteria, β-Proteobacteria, and Actinobacteria were the pioneer oil-degraders at the initial stage, and Firmicutes were considered to be able to degrade the recalcitrant components at the later stage. Copyright © 2014 Elsevier Ltd. All rights reserved.

Sustainable production of hydrogen and chemical commodities from biodiesel waste crude glycerol and cellulose by biological and catalytic processes

OpenAIRE

Maru, Biniam Taddele

2013-01-01

Hydrogen has a significant potential as clean and ‘green’ fuel of the future. Accordingly, this thesis investigated how to generate a sustainable production of hydrogen and other chemical commodities through study of: 1) Fermentative behavior of anaerobichydrogen producing microorganisms from pure glycerol and biodiesel waste crude glycerol; 2) The advantage of using a solid supportimmobilisationof microorganisms 3) The integration of the dark fermentative system with the catalytic hydrolysi...

Crude oil and natural gas supplies and demands for Denmark

International Nuclear Information System (INIS)

Mackay, R.M.; Probert, S.D.

1995-01-01

A novel technique for forecasting the supply and extraction life-cycle of a depleting fossil fuel resource has been developed. The supply side utilises a 'skewed-normal production-profile' model that yields a better representation than earlier approaches. A simple model for extrapolating crude oil and natural gas demands has also been devised, based on the so called 'modified logit function'. The predicted crude oil and natural gas balances for the period up to AD 2010 indicate the disparity between indigenous production and future consumption for Denmark. These forecasts depend on current estimates of remaining oil and gas reserves. It will consequently be necessary to revise periodically the present projections as more reliable reserve estimates become available. (author)

Additives In Meat and Poultry Products

Science.gov (United States)

... Fact Sheets / Additives in Meat and Poultry Products / Additives in Meat and Poultry Products Z7_0Q0619C0JGR010IFST1G5B10H3 ... Affairs Recalls and Public Health Alerts Regulatory Compliance Regulations, Directives and Notices Rulemaking ...

Crude glycerol combustion: particulate, acrolein, and other volatile organic emissions

Science.gov (United States)

Crude glycerol is an abundant by-product of biodiesel production. As volumes of this potential waste grow, there is increasing interest in developing new value added uses. One possible use, as a boiler fuel for process heating, offers added advantages of energy integration and ...

Cost and benefits for using NYMEX [New York Mercantile Exchange] crude oil futures

International Nuclear Information System (INIS)

Deaves, R.; Krinsky, I.

1991-01-01

The crisis in the Persian Gulf in 1990-91 has illustrated how important it is for end users of petroleum products to be able to reduce the risk of unexpected price changes. Transferring the risk of price changes, or hedging, is most desirable when the costs of doing so are low relative to the benefits. The nature of these benefits and costs are discussed, and a related analysis of data from the New York Mercantile Exchange (NYMEX) crude oil futures market is reported. It is shown that likely risk reduction is directly related to the degree to which the crude oil futures market can be characterized as efficient. Using data from the highly volatile period of 1983-90, evidence is presented to support the proposition that the crude oil market is efficient. There is no evidence for the existence of risk premiums, which constitute an additional cost to hedging. This is good news for hedgers, as it implies that risk transfer is free in the sense that hedgers need pay no premium to speculators. Although the market appears to be efficient when past returns and the basis are used as explanatory variables, there is some evidence that futures returns may be predicted using macroeconomic variables. 8 refs., 4 tabs

Hedging strategy for crude oil trading and the factors influencing hedging effectiveness

International Nuclear Information System (INIS)

Yun, Won-Cheol; Jae Kim, Hyun

2010-01-01

This study analyzes the hedging effectiveness of different hedge type and period by Korean oil traders. Both crude oil price and exchange rate risks are considered. Theoretical models are formulated to estimate the hedge ratios by separate and complex hedge types. The hedging period covers 1-12 months. This study also performs some statistical works to investigate the relationship between the hedging effectiveness and the crude oil price sensitivity to exchange rate. In addition, the relationship between the hedging effectiveness and the volatilities of crude oil price and exchange rate is analyzed. (author)

Formulation of best-fit hydrophile/lipophile balance-dielectric permittivity demulsifiers for treatment of crude oil emulsions

Directory of Open Access Journals (Sweden)

C.M. Ojinnaka

2016-12-01

Full Text Available The commerce of crude oil depends heavily on its water and salt contents usually referred to as Basic Sediments and Water (BS&W, which is co-produced with the crude oil in the form of emulsion. The lower the BS&W, the higher the market value of the crude. The presence of water in crude oil causes corrosion, lowers capacity utilization of production and processing plant parts and pipelines, reduces oil recovery and increases the oil content of the effluent water. The stabilizing factors of crude oil emulsions vary from one oil field to the other and with time in the same well as co-produced water increases, or after a well treatment and Enhanced Oil Recovery Operations (EOR. Periodical assessment and possible change of demulsifiers employed is therefore necessary at certain stages of crude oil productions, but this is not encouraged due to lack of general formulation procedures and the rigorous nature of bottle test method that is currently being used for assessment and selection. In this paper, the factors that affect the stability of crude oil emulsions are presented. Efforts of researchers in formulating demulsifiers based on these factors and their screening methods were reviewed. The context sets the stage for further exploration of possible relationship(s between the physical parameters of the crude oil and the demulsifiers, and exploiting same in the formulation of new demulsifiers capable of resolving crude oil emulsions using chemicals with improved surface activity and crude extracts of indigenous plants.

Crude oil burning mechanisms

DEFF Research Database (Denmark)

van Gelderen, Laurens; Malmquist, L.M.V.; Jomaas, Grunde

2015-01-01

In order to improve predictions for the burning efficiency and the residue composition of in-situ burning of crude oil, the burning mechanism of crude oil was studied in relation to the composition of its hydrocarbon mixture, before, during and after the burning. The surface temperature, flame...... height, mass loss rate and residues of three hydrocarbon liquids (n-octane, dodecane and hexadecane), two crude oils (DUC and REBCO) and one hydrocarbon liquid mixture of the aforementioned hydrocarbon liquids were studied using the Crude Oil Flammability Apparatus. The experimental results were compared...... on the highest achievable oil slick temperature. Based on this mechanism, predictions can then be made depending on the hydrocarbon composition of the fuel and the measured surface temperature....

Methods of analyzing crude oil

Science.gov (United States)

Cooks, Robert Graham; Jjunju, Fred Paul Mark; Li, Anyin; Rogan, Iman S.

2017-08-15

The invention generally relates to methods of analyzing crude oil. In certain embodiments, methods of the invention involve obtaining a crude oil sample, and subjecting the crude oil sample to mass spectrometry analysis. In certain embodiments, the method is performed without any sample pre-purification steps.

7 CFR 29.3015 - Crude.

Science.gov (United States)

2010-01-01

... of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Crude. A subdegree of maturity. Crude leaves are usually hard and slick as a result of extreme immaturity. A similar condition may result from sunburn or sunscald. Any leaf which is crude to the extent of...

CARBON DIOXIDE EMISSION ASSOCIATED WITH THE PRODUCTION OF PLASTICS - A COMPARISON OF PRODUCTION FROM CRUDE OIL AND RECYCLING FOR THE DUTCH CASE

DEFF Research Database (Denmark)

Rem, Peter C.; Olsen, Stig Irving; Welink, Jan-Henk

2009-01-01

recycling to the production of plastics from crude oil as a reference. The first scenario deals with packaging waste from selective collection, in which data from the current practice of the German DSD system were translated for the Dutch situation. In the second scenario, plastic packaging recovered from...... household waste using mechanical separation techniques is considered. It is assumed in the second scenario that the plastics are separated from the rest of the household waste and processed further to a compound close to the site at which the rest of the waste is disposed of, e.g. at an incinerator plant...

Benchmark West Texas Intermediate crude assayed

International Nuclear Information System (INIS)

Rhodes, A.K.

1994-01-01

The paper gives an assay of West Texas Intermediate, one of the world's market crudes. The price of this crude, known as WTI, is followed by market analysts, investors, traders, and industry managers around the world. WTI price is used as a benchmark for pricing all other US crude oils. The 41 degree API < 0.34 wt % sulfur crude is gathered in West Texas and moved to Cushing, Okla., for distribution. The WTI posted prices is the price paid for the crude at the wellhead in West Texas and is the true benchmark on which other US crudes are priced. The spot price is the negotiated price for short-term trades of the crude. And the New York Mercantile Exchange, or Nymex, price is a futures price for barrels delivered at Cushing

Crude value management through pipeline systems

Energy Technology Data Exchange (ETDEWEB)

Segato, R. [Suncor Energy Marketing Inc., Calgary, AB (Canada)

2009-07-01

This presentation reviewed Suncor's integrated oil flow operations with particular focus on the best practices in crude oil quality management from source rocks to refineries. Suncor produces synthetic crude at its operations in Fort McMurray, Alberta. The crude reaches destinations across North America. The quality of injected and delivered crude varies because of pipeline and terminal logistics, which implies changes in valuation. Refinery planners, engineers and crude traders are faced with the challenge of maximizing profitability while minimizing risk. Refiners face a continuously changing landscape in terms of crude classifications, new commodity developments, batch interferences, shared tank bottoms and sampling limitations. tabs., figs.

15 CFR 754.2 - Crude oil.

Science.gov (United States)

2010-01-01

... processed through a crude oil distillation tower. Included are reconstituted crude petroleum, and lease... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Crude oil. 754.2 Section 754.2....2 Crude oil. (a) License requirement. As indicated by the SS notation in the “License Requirements...

The empirical role of the exchange rate on the crude-oil price formation

International Nuclear Information System (INIS)

Yousefi, A.; Wirjanto, T.S.; University of Waterloo, Ont.

2004-01-01

This paper adopts a novel empirical approach to the crude-oil price formation for the purpose of understanding the price reactions of OPEC member countries to changes in the exchange rate of the US dollar against other major currencies and prices of other members. The results are broadly consistent with the view of the absence of a unified OPEC determined price in the international crude market literature. In addition, the results also highlight a cross regional dimension of the crude oil market. (author)

Effect of fertilizer formulation and bioaugmentation on biodegradation and leaching of crude oils and refined products in soils.

Science.gov (United States)

Coulon, F; Brassington, K J; Bazin, R; Linnet, P E; Thomas, K A; Mitchell, T R; Lethbridge, G; Smith, J W N; Pollarda, S J T

2012-09-01

The effects of soil characteristics and oil types as well as the efficacy of two fertilizer formulations and three bioaugmentation packages in improving the bioremediation of oil-contaminated soils were assessed as a means of ex situ treatment selection and optimization through seven laboratory microcosm studies. The influence of bioremediation on leaching of oil from the soil was also investigated. The studies demonstrated the benefits ofbiostimulation to overcome nutrient limitation, as most of the soils were nutrient depleted. The application of both liquid and pelleted slow-release N and P fertilizers increased both the hydrocarbon biodegradation rates (by a factor of 1.4 to 2.9) and the percentage of hydrocarbon mass degraded (by > 30% after 12 weeks and 80% after 37 weeks), when compared with the unamended soils. Slow-release fertilizers can be particularly useful when multiple liquid applications are not practical or cost-effective. Bioaugmentation products containing inoculum plus fertilizer also increased biodegradation by 20% to 37% compared with unamended biotic controls; however, there was no clear evidence of additional benefits due to the inocula, compared with fertilizer alone. Therefore biostimulation is seen as the most cost-effective bioremediation strategy for contaminated soils with the levels of crude oil and refined products used in this study. However, site-specific considerations remain essential for establishing the treatability of oil-contaminated soils.

Speculation and volatility spillover in the crude oil and agricultural commodity markets: A Bayesian analysis

International Nuclear Information System (INIS)

Du Xiaodong; Yu, Cindy L.; Hayes, Dermot J.

2011-01-01

This paper assesses factors that potentially influence the volatility of crude oil prices and the possible linkage between this volatility and agricultural commodity markets. Stochastic volatility models are applied to weekly crude oil, corn, and wheat futures prices from November 1998 to January 2009. Model parameters are estimated using Bayesian Markov Chain Monte Carlo methods. Speculation, scalping, and petroleum inventories are found to be important in explaining the volatility of crude oil prices. Several properties of crude oil price dynamics are established, including mean-reversion, an asymmetry between returns and volatility, volatility clustering, and infrequent compound jumps. We find evidence of volatility spillover among crude oil, corn, and wheat markets after the fall of 2006. This can be largely explained by tightened interdependence between crude oil and these commodity markets induced by ethanol production.

Short-term outlook for Canadian crude oil to 2006 : an energy market assessment

International Nuclear Information System (INIS)

2005-09-01

The National Energy Board monitors the supply of all energy commodities in Canada along with the demand for Canadian energy commodities in domestic and export markets. This report is intended to expand the effectiveness of the Board's monitoring activities by providing an assessment of the current state of the petroleum industry and the potential for growth. It provides an 18-month outlook on international and domestic crude oil prices; drilling and exploration activity; supply projections for Canadian crude oil and petroleum products; Canada's crude oil trade balance and markets for Canadian crude; existing export pipeline networks and project expansion plans; and, the Canadian petroleum products industry and the impact of higher prices. It also identifies the major issues and challenges associated with the development of Canada's crude oil. The 2 major oil producing areas in Canada are the Western Canada Sedimentary Basin (WCSB) including the oil sands, and offshore eastern Canada. While conventional production in the WCSB is declining, development focus has shifted to Alberta's oil sands as well as Hibernia, Terra Nova and White Rose, the 3 major oil fields offshore Newfoundland and Labrador. High energy prices have resulted in record profits for the Canadian oil and gas industry, and has stimulated billions of dollars in investment, with Alberta's oil sands being the main beneficiary. The 19 refineries in Canada have been operating at about 90 per cent capacity for the last several years due to strong demand for transportation fuels. 10 tabs., 37 figs., 2 appendices

Exports of crude oil, 1988

International Nuclear Information System (INIS)

1989-06-01

Effective June 1, 1985, licensing and charging of oil exports ended. The Board now issues export orders specifying neither volumes nor prices and covering an exportation period of up to 1 year for light crude oil and up to 2 years for heavy crude oil, available on request to both Canadian and foreign companies. The Board has assumed a monitoring role, and export prices and volumes are reported monthly by exporters. This annual report provides a review of the volumes and prices associated with the supply and disposition of Canadian crude oil during 1988. Highlights are given with detailed information on prices, both internationally, in Canada, and the Chicago posted price by light or heavy crude, and on volumes including capacity and disposition in both domestic and export markets. A short description of the import market is included. Comparisons are made with the previous year. Export volumes of light crude oil in 1988 increased by 13% to average 50,200 m 3 /d. Export volumes of heavy crude also increased by ca 13% to 62,600 m 3 /d. 15 figs., 2 tabs

THE INFLUENCE OF CRUDE SHEABUTTER LEAF-EXTRACTS ON ...

African Journals Online (AJOL)

AGROSEARCH UIL

INTRODUCTION ... Sheabutter tree, Vitellaria paradoxa is a tropical plant of numerous domestic and ... adoptable by rural farmers for increased productivity. ... crude protein requirements (NRC, 1981) for maintenance and weight gain in the goat. ... Total faeces and urine produced daily by each goat were collected and ...

A reexamination of the crude oil price-unemployment relationship in the United States

International Nuclear Information System (INIS)

Uri, N.D.; Boyd, R.

1996-01-01

This study begins by asking whether fluctuations in the price of crude oil have affected employment and the rate of unemployment in the US. After reviewing previous assessments of the issue, the existence of an empirical relationship between the rate of unemployment and crude oil price volatility is established using Granger causality. Subsequently, the nature of the relationship is estimated with the results suggesting that at least three full years are required before the measurable impact of a percentage change in the real price of crude oil on the change in unemployment is exhausted. Finally, the structural stability of the functional relationship between the change in unemployment and the volatility of the price of crude oil and the percentage change in gross national product is examined

The role of Canadian heavy crude oil in the North American market

Energy Technology Data Exchange (ETDEWEB)

Mink, F J; Antonia, H A

1977-01-01

Canadian reserves of heavy gravity crude oil are vast and the potential producibility from those reserves is expected to be surplus to Canadian requirements into the 1990s. This study focuses on the impact that market constraints may have on the future supply of heavy gravity crude oils from the W. Canadian basin. It observes that severe export restrictions will not only limit the orderly development of available reserves in the area but also will impair the prospects of additional enhanced recovery of conventional heavy crude reserves and restrict future experimental applications of oil sands recovery in the Cold Lake deposit of Alberta. Since it is expected that export restrictions for heavy gravity crude oil will be lifted in the future, the outlook for expanded development of indigenous reserves is promising.

Toxity of Gedunin, Piperine and Crude Extracts of their Natural ...

African Journals Online (AJOL)

Toxity of Gedunin, Piperine and Crude Extracts of their Natural Products on Growth and Development of Ostrinia Nubilalis Hbner (Lepidoptera: Pyrarlidae). F K Ewete, J T Arnason, T Durst, S Mackinnon ...

Radiation doses and hazards from processing of crude oil at the Tema oil refinery in Ghana

International Nuclear Information System (INIS)

Darko, E. O.; Kpeglo, D. O.; Akaho, E. H. K.; Schandorf, C.; Adu, P. A. S.; Faanu, A.; Abankwah, E.; Lawluvi, H.; Awudu, A. R.

2012-01-01

Processing of crude oil has been carried out in Ghana for more than four decades without measures to assess the hazards associated with the naturally occurring radionuclides in the raw and processed materials. This study investigates the exposure of the public to 226 Ra, 232 Th and 40 K in crude oil, petroleum products and wastes at the Tema oil refinery in Ghana using gamma-ray spectrometry. The study shows higher activity concentrations of the natural radionuclides in the wastes than the crude oil and the products with estimated hazard indices less than unity. The values obtained in the study are within recommended limits for public exposure indicating that radiation exposure from processing of the crude oil at the refinery does not pose any significant radiological hazard but may require monitoring to establish long-term effect on both public and workers. (authors)

Radiation doses and hazards from processing of crude oil at the Tema oil refinery in Ghana.

Science.gov (United States)

Darko, E O; Kpeglo, D O; Akaho, E H K; Schandorf, C; Adu, P A S; Faanu, A; Abankwah, E; Lawluvi, H; Awudu, A R

2012-02-01

Processing of crude oil has been carried out in Ghana for more than four decades without measures to assess the hazards associated with the naturally occurring radionuclides in the raw and processed materials. This study investigates the exposure of the public to (226)Ra, (232)Th and (40)K in crude oil, petroleum products and wastes at the Tema oil refinery in Ghana using gamma-ray spectrometry. The study shows higher activity concentrations of the natural radionuclides in the wastes than the crude oil and the products with estimated hazard indices less than unity. The values obtained in the study are within recommended limits for public exposure indicating that radiation exposure from processing of the crude oil at the refinery does not pose any significant radiological hazard but may require monitoring to establish long-term effect on both public and workers.

Concentration of vanadium in crude oil and water using inductively-coupled plasma spectrometry

International Nuclear Information System (INIS)

Amin, Y.M.; Hassan, M.A.; Junkin, K.; Mahat, R.H.; Raphie, B.

1991-01-01

Vanadium is a trace element that is usually associated to crude oil and its products. In this study the concentration of vanadium in a few samples of local crude oil, sea and river water were determined using inductively-coupled plasma spectrometry (ICP). It is hoped that the concentration of vanadium in water can be used to indicate the possible extent of oil contamination

Microbial ecology of methanogenic crude oil biodegradation; from microbial consortia to heavy oil

Energy Technology Data Exchange (ETDEWEB)

Head, Ian M.; Maguire, Michael J.; Sherry, Angela; Grant, Russell; Gray, Neil D.; Aitken, Carolyn M.; Martin Jones, D.; Oldenburg, Thomas B.P.; Larter, Stephen R. [Petroleum Research Group, Geosciences, University of Calgary (Canada)

2011-07-01

This paper presents the microbial ecology of methanogenic crude oil biodegradation. Biodegraded petroleum reservoirs are one of the most dramatic indications of the deep biosphere. It is estimated that heavy oil and oil sands will account for a considerable amount of energy production in the future. Carbon, a major resource for deep subsurface microorganisms, and energy are contained in large quantities in petroleum reservoirs. The aerobic to anaerobic paradigm shift is explained. A key process for in-situ oil biodegradation in petroleum reservoirs is methanogenesis. New paradigms for in-reservoir crude oil biodegradation are discussed. Variations in anaerobic degradation of crude oil hydrocarbons are also discussed. A graph shows the different patterns of crude oil biodegradation under sulfate-reducing and methanogenic conditions. Alternative anaerobic alkane activation mechanisms are also shown. From the study, it can be concluded that methanogenic crude oil degradation is of global importance and led to the establishment of the world's enormous heavy oil deposits.

Introduction of Fusarium sp. UTMC 5039 as a potent fungal strain for biosurfactant production and evaluation of its potential for crude oil bioremediation

Directory of Open Access Journals (Sweden)

Hamid Moghimi

2017-09-01

Full Text Available Introduction: Biosurfactants are biological surface active agents which are used in many applications such as oil bioremediation of contaminated soils. Materials and methods: In this study, first soil samples were collected from crude oil contaminated regions of Iran. Fungal isolates were enriched in MSM medium supplemented with crude oil and purified and then all isolates were screened for biosurfactant activity. Then, the capacity of crude oil degradation in the selected isolate was measured using Total Petroleum Hydrocarbon (TPH assay by spectrophotometry and FT-IR analysis. Finally, morphological and molecular identification was carried out by sequencing amplification of beta-tubuline beta-tubulin and ITS gene. Results: Among 40 purified fungal isolated, the isolate SH-02 was selected as the best strain according to the oil spreading and parafilm M test., This isolate was purified from petroleum contaminated soil of Arak refinery. Morphological and molecular identification revealed that this isolate has 99% similarity to Fusarium redolens in ITS geneand was deposited in the University of Tehran Microorganisms Collection under the accession number, UTMC 5039. Measurement of surface tension reduction by Du Nouy Ring method showed that Fusarium sp. UTMC 5039 can reduce surface tension to 26.6 mN/m and this reduction amount is significant compared with the previous reports. According to the obtained results from TPH and FTIR assays,  60 % of crude oil was degraded biodegradation was measured for by  Fusarium sp. UTMC 5039. Discussion and conclusion: The current study results indicate that Fusarium sp. UTMC 5039 has a high capacity in biosurfactant production and introduced as a potent fungal strain for crude oil bioremediation.

Development of a thermally-intensive reactor and process for upgrading heavy crude oil

Energy Technology Data Exchange (ETDEWEB)

Hauptmann, E.G. [Refinery Science Corp., El Paso, TX (United States)

2008-07-01

This paper discussed a pilot study conducted to test the performance of a 15 bpd high thermal flux short vapor residence time reactor. The technology was comprised of a flowing, free-surface channel of molten metal salts. Heavy crude droplets were placed on the flowing surface and mixed with catalysts. A free vapor space was used to remove and condense the clean, particulate-free cracked hydrocarbon vapors. An additional process was used to remove and separate the coke, catalysts and heavy metals for further processing and recovery. Placing the heavy crude onto a hot surface caused the drops to float or sputter on the surface. As the temperature increased, the film became thinner and broke down at the Leidenfrost point. A peak heat transfer coefficient then occurred during the intense nucleate boiling at the drop surface. The heavy crude was cracked through the combined effects of rapid heating and the presence of the catalyst. The clean, cracked hydrocarbon vapors were then removed from the drops and away from the heating source. Heavy metals were removed from the liquid product and discharged from the reactor with the coke and the catalyst. It was concluded that tests conducted to evaluate the performance of the technology demonstrated that the reactor required no external fuel for continuous operation after start-up, and all process water was fully recyclable. 5 refs., 2 tabs., 9 figs.

Additive manufacturing in production: challenges and opportunities

Science.gov (United States)

Ahuja, Bhrigu; Karg, Michael; Schmidt, Michael

2015-03-01

Additive manufacturing, characterized by its inherent layer by layer fabrication methodology has been coined by many as the latest revolution in the manufacturing industry. Due to its diversification of Materials, processes, system technology and applications, Additive Manufacturing has been synonymized with terminology such as Rapid prototyping, 3D printing, free-form fabrication, Additive Layer Manufacturing, etc. A huge media and public interest in the technology has led to an innovative attempt of exploring the technology for applications beyond the scope of the traditional engineering industry. Nevertheless, it is believed that a critical factor for the long-term success of Additive Manufacturing would be its ability to fulfill the requirements defined by the traditional manufacturing industry. A parallel development in market trends and product requirements has also lead to a wider scope of opportunities for Additive Manufacturing. The presented paper discusses some of the key challenges which are critical to ensure that Additive Manufacturing is truly accepted as a mainstream production technology in the industry. These challenges would highlight on various aspects of production such as product requirements, process management, data management, intellectual property, work flow management, quality assurance, resource planning, etc. In Addition, changing market trends such as product life cycle, mass customization, sustainability, environmental impact and localized production will form the foundation for the follow up discussion on the current limitations and the corresponding research opportunities. A discussion on ongoing research to address these challenges would include topics like process monitoring, design complexity, process standardization, multi-material and hybrid fabrication, new material development, etc.

Ingestive behavior of lactating cows fed sugarcane and crude glycerin levels on the diet

Directory of Open Access Journals (Sweden)

Lucas Teixeira Costa

2014-09-01

Full Text Available The crude glycerin used as feed for ruminants has drawn attention of the researchers for dealing with environmental aspects. Considering current legislation did not establish how to treat this product, this is a low cost alternative of great amount of a residue of the biodiesel production. In this study we evaluated different crude glycerin levels on ingestive behavior which were studied as the diet of lactating cows fed with sugarcane. The glycerin levels were 0, 4, 8 and 12% of the dry matter; the diet was balanced to contain enough nutrients for the maintenance and milk production of 15 kg.dia-1. Sixteen (16 crossbred Holstein x Zebu cows were distributed into four 4x4 Latin Squares. The animals were submitted to observation of 24 hours every five minutes to evaluate ingestive behavior. The observation of the activities was recorded. The animal´s behavior was visually determined with five minutes of intervals to determine the times spent in idle, feeding, rumination, and were calculated patterns of feeding and rumination. The addition of glycerin to the diet did not affect the ingestive behavior parameter in lactating cows fed sugarcane, might be explained by the similarity in NDF content of diets, and up to 12% may be added of the diet’s dry matter.

Crude oil spot market pricing: Pearsonian analysis of crude oil spot market prices

International Nuclear Information System (INIS)

Akinnusi, Ayo

1994-01-01

This paper presents a brief overview of crude oil pricing before describing a study of sets of 1991 spot market prices, and examining Pearson's model. Empirical distribution characteristics for 14 crude oils are tabulated, and skewness-kurtosis relationship and implication are considered. (UK)

Effects of Crude Oil and Oil Products on Growth of Some Edible ...

African Journals Online (AJOL)

The vegetative growth response of three local edible mushrooms: Pleurotus pulmonarius (Pp), Pleurotus tuber-regium (Pt) and Lentinus squarrosulus (Ls) on different concentrations of Crude oil (COIL), Automotive Gasoline Oil (AGO), Fresh Engine Oil (ENGOIL) and Spent Engine Oil (SENGOIL) was investigated. The result ...

Profiling of Indigenous Microbial Community Dynamics and Metabolic Activity During Enrichment in Molasses-Supplemented Crude Oil-Brine Mixtures for Improved Understanding of Microbial Enhanced Oil Recovery.

Science.gov (United States)

Halim, Amalia Yunita; Pedersen, Dorthe Skou; Nielsen, Sidsel Marie; Lantz, Anna Eliasson

2015-06-01

Anaerobic incubations using crude oil and brine from a North Sea reservoir were conducted to gain increased understanding of indigenous microbial community development, metabolite production, and the effects on the oil-brine system after addition of a complex carbon source, molasses, with or without nitrate to boost microbial growth. Growth of the indigenous microbes was stimulated by addition of molasses. Pyrosequencing showed that specifically Anaerobaculum, Petrotoga, and Methanothermococcus were enriched. Addition of nitrate favored the growth of Petrotoga over Anaerobaculum. The microbial growth caused changes in the crude oil-brine system: formation of oil emulsions, and reduction of interfacial tension (IFT). Reduction in IFT was associated with microbes being present at the oil-brine interphase. These findings suggest that stimulation of indigenous microbial growth by addition of molasses has potential as microbial enhanced oil recovery (MEOR) strategy in North Sea oil reservoirs.

The preparation and application of crude cellulase for cellulose-hydrogen production by anaerobic fermentation

Energy Technology Data Exchange (ETDEWEB)

Guo, Yi-Ping; Fan, Yao-Ting; Pan, Chun-Mei; Hou, Hong-Wei [Department of Chemistry, Zhengzhou University, Zhengzhou, Henan 450052 (China); Fan, Shao-Qun [Department of Chemistry, Zhengzhou University, Zhengzhou, Henan 450052 (China); Beijing Alcatel-Lucent R and D Center, Beijing, 100102 (China)

2010-01-15

Strategies were adopted to cost-efficiently produce cellulose-hydrogen by anaerobic fermentation in this paper. First, cellulase used for hydrolyzing cellulose was prepared by solid-state fermentation (SSF) on cheap biomass from Trichoderma viride. Several cultural conditions for cellulase production on cheap biomass such as moisture content, inoculum size and culture time were studied. And the components of solid-state medium were optimized using statistical methods to further improve cellulase capability. Second, the crude cellulase was applied to cellulose-hydrogen process directly. The maximal hydrogen yield of 122 ml/g-TVS was obtained at the substrate concentration of 20 g/L and cultured time of 53 h. The value was about 45-fold than that of raw corn stalk wastes. The hydrogen content in the biogas was 44-57%(v/v) and there was no significant methane gas observed. (author)

Test methods for determining asphaltene stability in crude oils

Energy Technology Data Exchange (ETDEWEB)

Asomaning, S. [Baker Petrolite, Sugar Land, TX (United States)

2001-07-01

The development of test methods for the determination of the stability of asphaltenes in crude oils was rendered necessary, due to the high cost of remediating asphaltene deposition in harsh production environments, namely the underwater systems in offshore deepwater. The Oliensis Spot Test, two saturates, aromatics, resins and asphaltenes (SARA)-based screens (the Colloidal Instability Index and Asphaltene-Resin ratio), a solvent titration method with near infrared radiation (NIR) solids detection, and live oil depressurization were used for the purposes of this study, to predict the stability of asphaltenes in crude oils with different API gravity. A complete description of the test methods was provided, and the experimental data obtained as a result was presented. Correlation with data on the deposition histories of the oils was used to validate the experimental stability data. The author discussed the effectiveness of the different tests for the prediction of the stability of asphaltenes in crude oils. The prediction of a crude oil's propensity towards asphaltene precipitation was more accurate with the Colloidal Instability Index and the solvent titration method. Live oil depressurization proved to be very effective for the prediction of the stability of asphaltenes for light oils, where most stability tests fail. tabs., 31 figs.

Energy saving in crude oil atmospheric distillation columns by modifying the vapor feed inlet tray

Energy Technology Data Exchange (ETDEWEB)

Arjmand, M. [Royal Institute of Technology (KTH), Graduate School of Chemical Engineering, Stockholm (Sweden); Moreno, L.; Liu, L. [Royal Institute of Technology (KTH), Department of Chemical Engineering and Technology, Stockholm (Sweden)

2011-08-15

Optimization of a typical crude oil atmospheric distillation unit and reduction of energy conservation were carried out through modifying the implementation and change in the flash zone of the tower. A conventional procedure in such units involves the combination of liquid and vapor product of the prefractionation train surge drum upon introduction to the tower. However, it is theoretically illustrated and represented by simulation means that introducing the vapor feed into the upper stages of the distillation column separately can lead to an energy saving of 12.6 % in the condenser duty, an increased liquid-to-gas flow (L/G) at certain points of the column, and hence to a reduction in diameter and investment costs of new tower designs of approximately US$ 0.7 million a{sup -1}. The proposal can be put into practice without the need of additional equipments or additional cost of difficult rerouting the streams. An industrial case study of a steady-state crude oil distillation unit is given by simulation provision of AspenHysys trademark. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Pelagia noctiluca (Scyphozoa Crude Venom Injection Elicits Oxidative Stress and Inflammatory Response in Rats

Directory of Open Access Journals (Sweden)

Giuseppe Bruschetta

2014-04-01

Full Text Available Cnidarian toxins represent a rich source of biologically active compounds. Since they may act via oxidative stress events, the aim of the present study was to verify whether crude venom, extracted from the jellyfish Pelagia noctiluca, elicits inflammation and oxidative stress processes, known to be mediated by Reactive Oxygen Species (ROS production, in rats. In a first set of experiments, the animals were injected with crude venom (at three different doses 6, 30 and 60 µg/kg, suspended in saline solution, i.v. to test the mortality and possible blood pressure changes. In a second set of experiments, to confirm that Pelagia noctiluca crude venom enhances ROS formation and may contribute to the pathophysiology of inflammation, crude venom-injected animals (30 µg/kg were also treated with tempol, a powerful antioxidant (100 mg/kg i.p., 30 and 60 min after crude venom. Administration of tempol after crude venom challenge, caused a significant reduction of each parameter related to inflammation. The potential effect of Pelagia noctiluca crude venom in the systemic inflammation process has been here demonstrated, adding novel information about its biological activity.

Record prices [crude oil

International Nuclear Information System (INIS)

Anon

2006-01-01

Crude oil prices climbed to new record levels on fears of a future loss of supplies from Iran as Washington stepped up its efforts to persuade Tehran to abandon its programme to produce nuclear fuel. IPE's December Brent contract set a new record for the exchange by trading at $75.80/bbl on 21st April. On the same day October WTI reached an all-time high of $77.30/bbl on Nymex. US product prices gained as refiners struggled to produce sufficient middle distillate. Alarmed by the rising retail price of gasoline, the US Senate debated a reduction in the already low US tax rate on motor spirit. The House of Representatives passed a measure to prohibit overcharging for petrol, diesel and heating oil, but Democrats rejected a Republican proposal to speed-up the process for approving new refineries. President George W Bush announced a temporary easing of new gasoline and diesel specifications (see 'Focus', March 2006) to allow more fuel to be produced. He also agreed to delay the repayment of some 2.1 mn bbl of crude oil lent to companies after last year's hurricanes from the Strategic Petroleum Reserve. California announced an inquiry into alleged overcharging for fuel by oil companies operating in the state. (author)

Soil microbial activity and hairy beggarticks’ germination after application of crude glycerin

Directory of Open Access Journals (Sweden)

Matheus Ramos Caixeta

Full Text Available ABSTRACT Biodiesel stands out as an alternative for petroleum-based products, but its production generates a large amount of by-products. This study was carried out at the Instituto Federal de Educação, Ciência e Tecnologia do Sul de Minas Gerais, Campus Machado, with the objective of evaluating the impacts of the disposal of crude glycerin on agricultural soil and its microbial activity as well as in plant development. An experiment with a completely randomized design, five treatments, and five replicates was developed in the laboratory to analyze microbial activity. Soil samples of 100 g were incubated for 36 days with concentrations of crude glycerin, namely: 0; 48.7; 146.1; 292.2 L ha-1. Besides these four treatments, flasks without soil and glycerin have composed one more treatment. During this period, the CO2 volume released in each sample was evaluated 11 times. Another experiment was developed in the laboratory with hairy beggarticks’ achenes to evaluate crude glycerin effects on plant development. A randomized complete block design was used in a 4x2 factorial scheme, with five replicates, the same glycerin concentrations, and two glycerin sources (laboratory and biodiesel plant-unit. Crude glycerin stimulated soil microbial activity for doses of up to 143.83 L ha-1, being a positive indicative for future studies on its application to agricultural soils. Glycerin applications reduced the hairy beggarticks’ root protrusion, even at the lowest doses. Residues have Na+ contents that limit their application in agricultural soils.

Sulfur transfer in the distillate fractions of Arabian crude oils under gamma-irradiation

International Nuclear Information System (INIS)

Basfar, Ahmed A.; Soliman, Yasser S.; Alkhuraiji, Turki S.

2017-01-01

Desulfurization of light distillation fractions including gasoline, kerosene and diesel obtained from the four Arabian crude oils (heavy, medium, light and extra light) upon γ-rays irradiation to different doses was investigated. In addition, yields vol%, FTIR analysis, kinematic viscosity and density of all distillation fractions of irradiated crude oils were evaluated. Limited radiation-induced desulfurization of those fractions was observed up to an irradiation dose of 200 kGy. FTIR analysis of those fractions indicates the absence of oxidized sulfur compounds, represented by S=O of sulfone group, indicating that γ-irradiation of the Arabian crude oils at normal conditions does not induce an oxidative desulfurization in those distillation fractions. Radiation-induced sulfur transfer decreases by 28.56% and increases in total sulfur by 16.8% in Arabian extra light oil and Arabian medium crude oil respectively. - Highlights: • Limited desulfurization in the light distillate fraction of Arabian crude oils using γ-rays was observed. • FTIR analysis confirms limited unchanged in density, viscosity and yields of Arabian crude oils. • In absence of oxidizer, radiation-induced sulfur transfer was observed in gasoline and diesel fractions of Arabian crude oils. • Radiation-induced oxidative desulfuration of the light distillate fractions depends on its characteristics.

Characterisation of crude oil components, asphaltene aggregation and emulsion stability by means of near infrared spectroscopy and multivariate analysis

Energy Technology Data Exchange (ETDEWEB)

Aske, Narve

2002-06-01

Effective separation of water-in-crude oil emulsions is a central challenge for the oil industry on the Norwegian Continental Shelf, especially with the future increase in subsea and even down-hole processing of well fluids. The mechanisms and properties governing emulsion stability are far from fully understood but the indigenous surface active crude oil components are believed to play a major role. In this work a thorough physico-chemical characterisation of a set of crude oils originating from a variety of production fields has been performed. Crude oil properties responsible for emulsion stability were identified by use of multivariate analysis techniques like partial least squares regression (PLS) and principal component analysis (PCA). Interfacial elasticity along with both asphaltene content and asphaltene aggregation state were found to be main contributors to emulsion stability. Information on a crude oils ability to form elastic crude oil-water interfaces was found to be especially crucial when discussing emulsion stability. However, measured values of interfacial elasticity were highly dependent on asphaltene aggregation state. Several experimental techniques was utilised and partly developed for the crude oil characterisation. A high-pressure liquid chromatography (HPLC) scheme was developed for SARA-fractionation of crude oils and an oscillating pendant drop tensiometer was used for characterisation of interfacial rheological properties. For emulsion stability a cell for determining the stability as a function of applied electric fields was used. In addition, near infrared spectroscopy (NIR) was used throughout the work both for chemical and physical characterisation of crude oils and model systems. High pressure NIR was used to study the aggregation of asphaltenes by pressure depletion. A new technique for detection of asphaltene aggregation onset pressures based on NIR combined with PCA was developed. It was also found that asphaltene aggregation is

Earthworms (Eisenia fetida) demonstrate potential for use in soil bioremediation by increasing the degradation rates of heavy crude oil hydrocarbons.

Science.gov (United States)

Martinkosky, Luke; Barkley, Jaimie; Sabadell, Gabriel; Gough, Heidi; Davidson, Seana

2017-02-15

Crude oil contamination widely impacts soil as a result of release during oil and gas exploration and production activities. The success of bioremediation methods to meet remediation goals often depends on the composition of the crude oil, the soil, and microbial community. Earthworms may enhance bioremediation by mixing and aerating the soil, and exposing soil microorganisms to conditions in the earthworm gut that lead to increased activity. In this study, the common composting earthworm Eisenia fetida was tested for utility to improve remediation of oil-impacted soil. E. fetida survival in soil contaminated with two distinct crude oils was tested in an artificial (lab-mixed) sandy loam soil, and survival compared to that in the clean soil. Crude oil with a high fraction of light-weight hydrocarbons was more toxic to earthworms than the crude oil with a high proportion of heavy polyaromatic and aliphatic hydrocarbons. The heavier crude oil was added to soil to create a 30,000mg/kg crude oil impacted soil, and degradation in the presence of added earthworms and feed, feed alone, or no additions was monitored over time and compared. Earthworm feed was spread on top to test effectiveness of no mixing. TPH degradation rate for the earthworm treatments was ~90mg/day slowing by 200days to ~20mg/day, producing two phases of degradation. With feed alone, the rate was ~40mg/day, with signs of slowing after 500days. Both treatments reached the same end point concentrations, and exhibited faster degradation of aliphatic hydrocarbons C21, decreased. During these experiments, soils were moderately toxic during the first three months, then earthworms survived well, were active and reproduced with petroleum hydrocarbons present. This study demonstrated that earthworms accelerate bioremediation of crude oil in soils, including the degradation of the heaviest polyaromatic fractions. Copyright © 2016 Elsevier B.V. All rights reserved.

Fish protein hydrolysate production from sardine solid waste by crude pepsin enzymatic hydrolysis in a bioreactor coupled to an ultrafiltration unit

International Nuclear Information System (INIS)

Benhabiles, M.S.; Abdi, N.; Drouiche, N.; Lounici, H.; Pauss, A.; Goosen, M.F.A.; Mameri, N.

2012-01-01

The aims of the study were to optimize the production a fish protein hydrolysate (FPH) by enzymatic hydrolysis of sardine solid waste using crude pepsin, and to scale up the process in a bioreactor coupled to an ultrafiltration unit for product recovery. Results showed that the crude pepsin prepared by autolysis of the mucous membranes of a sheep stomach at optimal conditions (i. e. pH = 1.5–2 and incubation time of 6 h) could be satisfactory used for the enzymatic hydrolysis of fish solid waste. The optimal conditions for enzymatic reaction were: temperature 48 °C, and pH 1.5. The scale up of the enzymatic hydrolysis and the coupling of the reactor an ultrafiltration unit to concentrate the hydrolysate gave good results with a rejection coefficient for the protein hydrolysate product in the range of 90%. The volumetric concentration factor was 2.5, with a permeate flux of 200 L m −2 bar −1 . However, the results also suggest that the ultrafiltration product concentration process may be operating beyond the critical flux at which point irreversible membrane fouling occurs. - Highlights: ► Evaluating to produce a (FPH) by enzymatic hydrolysis of sardine solid wastes was achieved. ► Investigation of key parameters for optimal conditions for enzymatic hydrolysis have been studied. ► Valorization of sardine waste was realized by enzymatic hydrolysis process. ► Performances of this enzyme gave comparable results to those obtained with commercial pepsin. ► The nutritional quality of the FPH produced appears to be satisfactory.

Biodegradation of crude oil by Pseudomonas aeruginosa in the presence of rhamnolipids*

OpenAIRE

Zhang, Guo-liang; Wu, Yue-ting; Qian, Xin-ping; Meng, Qin

2005-01-01

The potential biodegradation of crude oil was assessed based on the development of a fermentative process with a strain of Pseudomonas aeruginosa which produced 15.4 g/L rhamnolipids when cultured in a basal mineral medium using glycerol as a sole carbon source. However, neither cell growth nor rhamnolipid production was observed in the comparative culture system using crude oil as the sole carbon source instead. As rhamnolipid, an effective biosurfactant, has been reported to stimulate the b...

Qualitative characteristics of meat from young bulls fed different levels of crude glycerin.

Science.gov (United States)

Carvalho, J R R; Chizzotti, M L; Ramos, E M; Machado Neto, O R; Lanna, D P D; Lopes, L S; Teixeira, P D; Ladeira, M M

2014-02-01

The objective was to evaluate the fatty acid profile and qualitative characteristics of meat from young bulls fed crude glycerin. Forty-four animals with an initial live weight of 368 ± 4 kg were used in a completely randomized design, with four treatments: no glycerin or addition of 6, 12 or 18% glycerin. The animals were slaughtered with 519.5 ± 14.9 kg of live weight. The meat characteristics assessed were chemical composition, shear force, fatty acid concentration, color and lipid oxidation. The addition of glycerin increased the content of ether extract (P<0.05) in the muscle. A linear increase was observed (P<0.05) in the oleic acid contents (C18:1 cis 9). The saturated fatty acid (SFA) contents linearly decreased in the muscle as a function of glycerin addition. The lightness (L*) and yellowness (b*) indices increased with the use of crude glycerin (P<0.05). The crude glycerin increased the intramuscular fat and oleic acid content in the longissimus dorsi muscle. © 2013.

Electron beam sterilization of crude drug and its detection based on genetic analysis

Energy Technology Data Exchange (ETDEWEB)

Satake, Motoyoshi; Sekita, Setsuko; Kamakura, Hiroyuki [National Inst. of Health Sciences, Tokyo (Japan)

2000-02-01

Chinese traditional crude drugs are medicines derived from natural materials so that most of them include various microorganisms such as soil microbials. Therefore, it is needed to develop a sterilization method for crude drugs not disturbing the efficacy of them. As one of such sterilization method, electron beam sterilization is paid attention now. In this study, the sterilizing effects of electron beam irradiation at various doses were investigated and the changes of low molecular substances were monitored. Phellodendron bark, rehmannia root, bupleurum root and Japanese angelica root samples were used as the subjects. Irradiation was made with {gamma}-ray ({sup 60}Co) and electron beam at 5, 10, 20, 30 and 60 kGy and the number of organisms included in each drug and the contents of effective ingredients were determined after radiation exposure was determined. The number of microbials in these crude drugs were reduced ten times or more by electron beam irradiation, indicating that electron beam exposure has similar effects to those of {gamma}-ray exposure at 10 kGy previously reported. Furthermore, the contents of effective ingredients of crude drugs, especially low molecular substances such as berberine, saponin, catalpol were not significantly changed by the electron beam exposure at the doses tested in this study and electron beam exposure as well as {gamma}-ray exposure hardly affects those ingredients even at 60 kGy. Meanwhile, significant differences were observed in large molecular fractions of gel filtration chromatography between before and after the electron beam exposure at 60 kGy, suggesting that there were structural changes in some large molecules. In addition, to develop a detection method for these crude drugs, genomic DNA was extracted from them and digested with a restriction enzyme, MspI and EcoRI. Then, the ends of the respective DNAs were linked. After amplification by primary PCR, selective PCR was conducted with three MspI primers and Eco

Electron beam sterilization of crude drug and its detection based on genetic analysis

International Nuclear Information System (INIS)

Satake, Motoyoshi; Sekita, Setsuko; Kamakura, Hiroyuki

2000-01-01

Chinese traditional crude drugs are medicines derived from natural materials so that most of them include various microorganisms such as soil microbials. Therefore, it is needed to develop a sterilization method for crude drugs not disturbing the efficacy of them. As one of such sterilization method, electron beam sterilization is paid attention now. In this study, the sterilizing effects of electron beam irradiation at various doses were investigated and the changes of low molecular substances were monitored. Phellodendron bark, rehmannia root, bupleurum root and Japanese angelica root samples were used as the subjects. Irradiation was made with γ-ray ( 60 Co) and electron beam at 5, 10, 20, 30 and 60 kGy and the number of organisms included in each drug and the contents of effective ingredients were determined after radiation exposure was determined. The number of microbials in these crude drugs were reduced ten times or more by electron beam irradiation, indicating that electron beam exposure has similar effects to those of γ-ray exposure at 10 kGy previously reported. Furthermore, the contents of effective ingredients of crude drugs, especially low molecular substances such as berberine, saponin, catalpol were not significantly changed by the electron beam exposure at the doses tested in this study and electron beam exposure as well as γ-ray exposure hardly affects those ingredients even at 60 kGy. Meanwhile, significant differences were observed in large molecular fractions of gel filtration chromatography between before and after the electron beam exposure at 60 kGy, suggesting that there were structural changes in some large molecules. In addition, to develop a detection method for these crude drugs, genomic DNA was extracted from them and digested with a restriction enzyme, MspI and EcoRI. Then, the ends of the respective DNAs were linked. After amplification by primary PCR, selective PCR was conducted with three MspI primers and EcoRI primer. The

Crude Glycerol as Cost-Effective Fuel for Combined Heat and Power to Replace Fossil Fuels, Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Roberts, William L

2012-10-31

The primary objectives of this work can be summed into two major categories. Firstly, the fundamentals of the combustion of glycerol (in both a refined and unrefined form) were to be investigated, with emphasis of the development of a system capable of reliably and repeatedly combusting glycerol as well as an analysis of the emissions produced during glycerol combustion. Focus was placed on quantifying common emissions in comparison to more traditional fuels and this work showed that the burner developed was able to completely combust glycerol within a relatively wide range of operating conditions. Additionally, focus was placed on examining specific emissions in more detail, namely interesting NOx emissions observed in initial trials, acrolein and other volatile organic emissions, and particulate and ash emissions. This work showed that the combustion of crude glycerol could result in significantly reduced NOx emissions as a function of the high fuel bound oxygen content within the glycerol fuel. It also showed that when burned properly, the combustion of crude glycerol did not result in excessive emissions of acrolein or any other VOC compared to the combustion from more traditional fuels. Lastly however, this work has shown that in any practical application in which glycerol is being burned, it will be necessary to explore ash mitigation techniques due to the very high particulate matter concentrations produced during glycerol combustion. These emissions are comparable to unfiltered coal combustion and are directly tied to the biodiesel production method. The second focus of this work was directed to developing a commercialization strategy for the use of glycerol as a fuel replacement. This strategy has identified a 30 month plan for the scaling up of the laboratory scale burner into a pre-pilot scale system. Additionally, financing options were explored and an assessment was made of the economics of replacing a traditional fuel (namely natural gas) with crude

Molecular processes in the biodegradation of crude oils and crude oil products in the natural reservoir and in laboratory experiments

International Nuclear Information System (INIS)

Schalenbach, S.S.

1993-10-01

Two ains were pursued in the present study; first, to find positive indicators of the onset of biodegradation of reservoir oil wherever other parameters fail to give a clear picture; second, to establish a basic understanding of the molecular processes underlying the biodegradation of hydrocarbons and thus create a starting point for finding better criteria for valuating biological restoration methods for crude oil contaminated soils. (orig./HS) [de

Comparison of reduced sugar high quality chocolates sweetened with stevioside and crude stevia 'green' extract.

Science.gov (United States)

Torri, Luisa; Frati, Alessandra; Ninfali, Paolino; Mantegna, Stefano; Cravotto, Giancarlo; Morini, Gabriella

2017-06-01

The demand for zero and reduced-sugar food products containing cocoa is expanding continuously. The present study was designed to evaluate the feasibility of producing high-quality chocolate sweetened with a crude extract of Stevia rebaudiana (Bertoni) prepared by a green microwave-assisted water-steam extraction procedure. Seven approximately isosweet chocolate formulations were developed, mixing cocoa paste, sucrose, commercial stevioside, crude green extract and maltitol in different proportions. All samples were analyzed for the determination of polyphenol and flavonoid content, antioxidant activity, and sensory acceptability. The use of a crude stevia extract allowed low-sugar, high-quality chocolates to be obtained that were also acceptable by consumers and had a significant increased antioxidant activity. Moreover, consumers' segmentation revealed a cluster of consumers showing the same overall liking for the sample with 50% sucrose replaced by the stevia crude extract as that obtained with the commercial stevioside and the control sample (without sucrose replacement). The results provide information that can contribute to promoting the development of sweet food products, with advantages in terms of an improved nutritional value (reduced sugar content and increased antioxidant activity) and a reduced impact of the production process on the environment. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Energy optimization of crude oil distillation using different designs of pre-flash drums

International Nuclear Information System (INIS)

Al-Mayyahi, Mohmmad A.; Hoadley, Andrew F.A.; Rangaiah, G.P.

2014-01-01

The Crude Distillation Unit (CDU) is among the major CO 2 emitters in any petroleum refinery. In view of the simultaneous increase in the energy cost and environmental concerns, there is strong motivation to analyse alternative methods to improve the energy efficiency and consequently, to minimize CO 2 emissions from conventional crude distillation. Crude pre-flashing is among promising techniques for minimizing the heating energy requirements of the CDU. However, this might be at the cost of product yield and/or throughput. This paper investigates the effects of using different pre-flash designs on the energy efficiency and associated CO 2 emissions of the CDU. The resulting optimal solutions are presented and their significant features are discussed. - Highlights: • Single and multiple pre-flash designs of the crude distillation unit are studied. • The trade-off between CO 2 emissions and the residue yield has been investigated. • Multi-objective optimization was used to find the trade-off solutions. • Introducing crude pre-flashing reduces the total CO 2 emissions. • Optimum vapour feed location has been investigated

Crude protein changes on grassland along a degradation gradient ...

African Journals Online (AJOL)

Evapotranspiration was determined by quantifying the soil-water balance equation with the aid of runoff plots and soil-water content measurements. Crude protein ... The study shows that it is important to keep grassland in optimal condition to utilize limited soil water for sustainable plant and therefore animal production.

Production of crude enzyme from Aspergillus nidulans AKB-25 using black gram residue as the substrate and its industrial applications

Directory of Open Access Journals (Sweden)

Amit Kumar

2016-06-01

Full Text Available The production of crop residues in India is estimated to be about 500–550 million tons annually. It is estimated that about 93 million tons of crop residues is burnt annually which is not only wastage of valuable biomass resources but pollution of the environment with the production of green house gases also. Among different low cost crop residues, black gram residue as the substrate produced maximal endoglucanase, FPase, and β-glucosidase activities from Aspergillus nidulans AKB-25 under solid-state fermentation. During optimisation of cultural parameters A. nidulans AKB-25 produced maximal endoglucanase (152.14 IU/gds, FPase (3.42 FPU/gds and xylanase (2441.03 IU/gds activities. The crude enzyme was found effective for the saccharification of pearl millet stover and bio-deinking of mixed office waste paper. The crude enzyme from A. nidulans AKB-25 produced maximum fermentable sugars of 546.91 mg/g from alkali-pretreated pearl millet stover by saccharification process at a dose of 15 FPU/g of substrate. Pulp brightness and deinking efficiency of mixed office waste paper improved by 4.6% and 25.01% respectively and mitigated dirt counts by 74.70% after bio-deinking. Physical strength properties like burst index, tensile index and double fold number were also improved during bio-deinking of mixed office waste paper.

Production of xylanases and cellulases by aspergillus fumigatus ms16 using crude lignocellulosic substrates

International Nuclear Information System (INIS)

Naseeb, S.; Sohai, M.; Ahmad, A.; Khan, S.A.

2015-01-01

Xylanolytic and cellulolytic potential of a soil isolate, Aspergillus fumigatus (MS16) was studied by growing it on a variety of lignocellulosics, purified cellulose and xylan supplemented media. It was noted that carboxymethyl cellulose, salicin and xylan induce the -glucosidase and xylanase, respectively production of endoglucanase. The study revealed that Aspergillus fumigatus (MS16) co-secretes xylanase and cellulase in the presence of xylan; the ratio of the two enzymes was influenced by the initial pH of the medium. The maximum titers of xylanase and cellulase were noted at initial pH of 5.0. Relatively higher titers of both the enzymes were obtained when the fungus was cultivated at 35 degree C. Whereas, cellulase production was not detected when the fungus was cultivated at 40 degree C. The volumetric productivity (Qp) of xylanase was much higher than cellulases. The organism produced 2-3 folds higher titers of xylanase when grown on lignocellulosic materials in submerged cultivation than under solid-state cultivation, suggesting a different pattern of enzyme production in presence and in absence of free water. The partial characterization of enzymes showed that xylanase from this organism has -glucosidase. The higher melting temperature than endoglucanase and optimum temperature for activity was higher for xylanases than cellulases, whereas the optimum pH differed slightly i.e. in the range of 4.0-5.0. Enzyme preparation from this organism was loaded on some crude substrates and it showed that the enzyme preparation can be used to hydrolyze a variety of vegetable and agricultural waste materials. (author)

Sulfur transfer in the distillate fractions of Arabian crude oils under gamma-irradiation

Science.gov (United States)

Basfar, Ahmed A.; Soliman, Yasser S.; Alkhuraiji, Turki S.

2017-05-01

Desulfurization of light distillation fractions including gasoline, kerosene and diesel obtained from the four Arabian crude oils (heavy, medium, light and extra light) upon γ-rays irradiation to different doses was investigated. In addition, yields vol%, FTIR analysis, kinematic viscosity and density of all distillation fractions of irradiated crude oils were evaluated. Limited radiation-induced desulfurization of those fractions was observed up to an irradiation dose of 200 kGy. FTIR analysis of those fractions indicates the absence of oxidized sulfur compounds, represented by S=O of sulfone group, indicating that γ-irradiation of the Arabian crude oils at normal conditions does not induce an oxidative desulfurization in those distillation fractions. Radiation-induced sulfur transfer decreases by 28.56% and increases in total sulfur by 16.8% in Arabian extra light oil and Arabian medium crude oil respectively.

Environmental guidance documents for exploration, development, Production, and transportation of crude oil and natural gas in texas: Quarterly technical report, January 1, 1997-March 31, 1997

International Nuclear Information System (INIS)

Savage, L.

1997-01-01

The following technical report provides a detailed status report of the DOE grant project entitled ''Environmental Guidance Documents for Exploration, Development, Production, and Transportation of Crude Oil and Natural Gas in Texas.'' The grant funding allocated is for the purpose of provided the Railroad Commission of Texas (Commission) with resources and capabilities to draft, publish and distribute documents that provide guidance to oil and gas operators on issues concerning oil and gas naturally occurring radioactive material (NORM) waste, oil and gas hazardous waste, remediation of crude oil spills, management of non-hazardous oil and gas wastes, and mechanical integrity testing of Class II injection and disposal wells

Alternatives to conventional crude oil. When, how quickly, and market driven?

International Nuclear Information System (INIS)

Kaufmann, Robert K.; Shiers, Laura D.

2008-01-01

We examine the effect of uncertainty concerning remaining supplies of conventional crude oil and its production path on: the date alternative fuels will be needed, the quantity of alternative fuels needed, and how this uncertainty affects firms' willingness to provide alternatives in a timely fashion. Despite large uncertainties about the quantity of oil that remains and its production path, the start date for replacements is likely to fall within a twenty-two year period that is narrower and earlier than previous estimates. The twenty-two year window represents considerable uncertainty about the date of the peak and this uncertainty creates an asymmetry in the strategy that maximizes the welfare of firms relative to total social welfare, which works against the market's ability to generate a smooth transition from oil to alternative fuels. The timeliness of this transition is critical - the production paths generated here suggest that 10 million barrels per day or more of alternative fuels will be needed within a decade of the peak in production of conventional crude oil. (author)

Toxicopathology and immunotoxicology of multiple exposures to diesel and crude oils in cattle

International Nuclear Information System (INIS)

Dziwenka, M.M.; Coppock, R.W.; Khan, A.A.; Hiltz, M.N.; Nation, P.N.; Field, C.J.

2002-01-01

The subchronic toxicology of crude and refined petroleum in cattle was examined during the course of a large study in which 40 cattle were gavaged with potable water, winter diesel fuel and crude oil for a period of up to 48 days. Blood samples for clinicopathologic parameters were collected weekly. The cattle were necropsied 22 days following the last dose. Representative tissues were taken from all organ systems for histopathology. It was shown that repeated oral exposure to petroleum products resulted in significant changes in the clinicopathologic and immunopathologic parameters of the cattle without producing significant macro- or microscopic tissue lesions. The liver was a target organ for subchronic crude and diesel toxicity. 5 refs., 1 tab., 10 figs

Measurement of the Rheology of Crude Oil in Equilibrium with CO2 at Reservoir Conditions.

Science.gov (United States)

Hu, Ruien; Crawshaw, John

2017-06-06

A rheometer system to measure the rheology of crude oil in equilibrium with carbon dioxide (CO2) at high temperatures and pressures is described. The system comprises a high-pressure rheometer which is connected to a circulation loop. The rheometer has a rotational flow-through measurement cell with two alternative geometries: coaxial cylinder and double gap. The circulation loop contains a mixer, to bring the crude oil sample into equilibrium with CO2, and a gear pump that transports the mixture from the mixer to the rheometer and recycles it back to the mixer. The CO2 and crude oil are brought to equilibrium by stirring and circulation and the rheology of the saturated mixture is measured by the rheometer. The system is used to measure the rheological properties of Zuata crude oil (and its toluene dilution) in equilibrium with CO2 at elevated pressures up to 220 bar and a temperature of 50 °C. The results show that CO2 addition changes the oil rheology significantly, initially reducing the viscosity as the CO2 pressure is increased and then increasing the viscosity above a threshold pressure. The non-Newtonian response of the crude is also seen to change with the addition of CO2.

Fish protein hydrolysate production from sardine solid waste by crude pepsin enzymatic hydrolysis in a bioreactor coupled to an ultrafiltration unit

Energy Technology Data Exchange (ETDEWEB)

Benhabiles, M.S.; Abdi, N. [National Polytechnic school of Algiers, B.P. 182-16200, El Harrach, Algiers (Algeria); Drouiche, N., E-mail: nadjibdrouiche@yahoo.fr [National Polytechnic school of Algiers, B.P. 182-16200, El Harrach, Algiers (Algeria); Silicon Technology Development Unit (UDTS) 2, Bd Frantz Fanon BP140, Alger-7 Merveilles, 16000 (Algeria); Lounici, H. [National Polytechnic school of Algiers, B.P. 182-16200, El Harrach, Algiers (Algeria); Pauss, A. [University of Technology of Compiegne, Departement Genie chimique,B.P. 20.509, 60205 Compiegne cedex (France); Goosen, M.F.A. [Alfaisal University, Riyadh (Saudi Arabia); Mameri, N. [University of Technology of Compiegne, Departement Genie chimique,B.P. 20.509, 60205 Compiegne cedex (France)

2012-05-01

The aims of the study were to optimize the production a fish protein hydrolysate (FPH) by enzymatic hydrolysis of sardine solid waste using crude pepsin, and to scale up the process in a bioreactor coupled to an ultrafiltration unit for product recovery. Results showed that the crude pepsin prepared by autolysis of the mucous membranes of a sheep stomach at optimal conditions (i. e. pH = 1.5-2 and incubation time of 6 h) could be satisfactory used for the enzymatic hydrolysis of fish solid waste. The optimal conditions for enzymatic reaction were: temperature 48 Degree-Sign C, and pH 1.5. The scale up of the enzymatic hydrolysis and the coupling of the reactor an ultrafiltration unit to concentrate the hydrolysate gave good results with a rejection coefficient for the protein hydrolysate product in the range of 90%. The volumetric concentration factor was 2.5, with a permeate flux of 200 L m{sup -2} bar{sup -1}. However, the results also suggest that the ultrafiltration product concentration process may be operating beyond the critical flux at which point irreversible membrane fouling occurs. - Highlights: Black-Right-Pointing-Pointer Evaluating to produce a (FPH) by enzymatic hydrolysis of sardine solid wastes was achieved. Black-Right-Pointing-Pointer Investigation of key parameters for optimal conditions for enzymatic hydrolysis have been studied. Black-Right-Pointing-Pointer Valorization of sardine waste was realized by enzymatic hydrolysis process. Black-Right-Pointing-Pointer Performances of this enzyme gave comparable results to those obtained with commercial pepsin. Black-Right-Pointing-Pointer The nutritional quality of the FPH produced appears to be satisfactory.

Antioxidant effects and phytochemical analysis of crude and ...

African Journals Online (AJOL)

Eucalyptus globulus is extremely used in traditional medicine in Algeria and its leaf extract is included as one of the antioxidant in the list of existing food additives in Japan. In the present study, the crude extract from bark of this plant and its fractions obtained by Sephadex LH-20 column were studied to quantify their levels ...

Distribution and geochemical application of aromatic hydrocarbons in crude oils

International Nuclear Information System (INIS)

Asif, M.; Tahira, F.

2007-01-01

Distribution of aromatic hydrocarbons was studied in a set of crude oils, five from northern Indus basin of potwar area and two from southern Indus basin. Diaromatic and triaromatic hydrocarbons were separated from highly complex mixture of sedimentary organic matter by using liquid chromatography techniques such as column chromatography, TLC and GC-FID. These classes of compounds were identified to alkylated isomers of naphthalenes and phenanthrenes by using reference chromatograms and literature data. High concentration of di-,tri- and tetra-methyl naphthalenes was observed in all crude oils except Kal. The relative increase in concentration of alkyl naphthalenes was found as moved to higher methyl substituted isomers. This suggests that they are the product of sedimentary alkylation reactions during catagensis and metagensis. The significant concentration of methyl phenanthrenes indicated source of organic matter. High levels of both 1-MP and 9-MP showed marine and terrestrial source of organic matter except Umer crude oil which is most likely to have terrestrial origin. The ratios of beta-substituted to the alpha-substituted isomers of both alkyl naphthalenes and alkyl phenanthrene were used to assess the thermal maturity of sedimentary organic matter, which revealed high maturity level of Dhurnal, Pindori, Badin and Toot crude oils. (author)

Quantification of Greenhouse Gas Emissions for the Production of Crude Palm Kernel Oil - A Cradle to Gate Study

International Nuclear Information System (INIS)

Subramaniam, V.

2016-01-01

The Malaysian oil palm industry is one of the major economic backbones of the country. The industry as a whole brought in an export revenue of RM 63 billion just in the year 2015. In the past, the competitiveness of palm products along the supply chain was based on direct economic comparison with other vegetable oil products. However, with increasing attention on sustainable development, the environmental performance of products are now defining issues in trade. This articles presents the greenhouse gas (GHG) emissions for the production of crude palm kernel oil (CPKO). Crude palm oil (CPO) and CPKO both come from the oil palm fresh fruit bunch (FFB). CPO is obtained from the mesocarp of the fruit and the lauric CPKO comes from the kernel at the fruit's core. CPO is produced in the palm oil mill while palm kernels which are the by-product of the production of CPO are transported to kernel crushing plants to be processed into CPKO. The objectives of this study are to quantify the GHG emissions for the production of CPKO and suggest the best solution to reduce the emissions if any. The system boundary starts from the production of oil palm seedlings at the nursery stage right till the production of CPKO at the kernel crushing plant which makes it a cradle to gate study. Inventory data for the production of CPKO was collected from 24 crushing plants which were located near the ports and two kernel crushing plants which were integrated with a palm oil mill. Weight allocation was performed at the kernel crushing plant. The largest GHG contribution came from upstream nursery and plantation with continued land use which amounts to 394.19 kg CO 2 eq/ t CPKO followed by emissions from biogas at the palm oil mill which amounts to 87.48 kg CO 2 eq/ t CPKO even though the scenario chosen is the biogas capture scenario. The third largest GHG emissions comes from the kernel crushing plant due to the processing of CPKO using the electricity from the grid which emits 74.33 kg

Kinetic analysis of dihydroxyacetone production from crude glycerol by immobilized cells of Gluconobacter oxydans MTCC 904.

Science.gov (United States)

Dikshit, Pritam Kumar; Moholkar, Vijayanand S

2016-09-01

The present study has investigated kinetic features of bioconversion of biodiesel-derived crude glycerol to dihydroxyacetone with immobilized Gluconobacter oxydans cells using modified Haldane substrate-inhibition model. The results have been compared against free cells and pure glycerol. Relative variations in the kinetic parameters KS, KI, Vmax, n and X reveal that immobilized G. oxydans cells (on PU foam substrate) with crude glycerol as substrate give higher order of inhibition (n) and lower maximum reaction velocities (Vmax). These results are essentially implications of substrate transport restrictions across immobilization matrix, which causes retention of substrate in the matrix and reduction in fractional available substrate (X) for the cells. This causes reduction in both KS (substrate concentration at Vmax/2) and KI (inhibition constant) as compared to free cells. For immobilized cells, substrate concentration (Smax) corresponding to Vmax is practically same for both pure and crude glycerol as substrate. Copyright © 2016 Elsevier Ltd. All rights reserved.

Digestion of crude protein and organic matter of leaves by rumen microbes in vitro

Energy Technology Data Exchange (ETDEWEB)

Ciszuk, A.; Murphy, M.

1982-01-01

22 leaf specimens, of which 6 were from an energy-woods project, were studied by incubation in vitro with rumen microbes or pepsin-hydrochloric acid. Several were also examined in situ using the nylon-bag technique. Many leaves, despite their low fiber and high crude protein content, gave low values for organic matter digestibility. The crude protein degradation by rumen microbes or pepsin-hydrochloric acid was low, on average, compared with hay. There was a wide variation among leaf specimens. Variation was also found as regards ammonia production in short-term (4 hours) incubation. No close correlation was found between crude protein content and crude protein degradation, or between the estimates of ruminal degradation and of pepsin-hydrochloric acid digestibility. This suggest that there are leaves that gives ruminants substantial amounts of digestible protein yet escape ruminal fermentation. (Refs. 12).

Influence of heavy crude oil refining about the mains characteristics of jet fuel; Influencia do refino de petroleos pesados sobre as principais caracteristicas do combustivel de aviacao

Energy Technology Data Exchange (ETDEWEB)

Om, Neyda [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica; Cavado, Alberto; Reyes, Yordanka [Centro de Pesquisas do Petroleo, Cidade de Havana (Cuba); Salazar, Rodolfo [Centro de Eletromagnetismo Aplicado, Cidade de Havana (Cuba); Dominguez, Zulema [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE)

2004-07-01

The aviation technology in the world, is to use gas turbines engines feted for fuel type Jet A1. The main exigency of quality for this products is concentrated in extreme security and secure answer during the functioning. The conductivity and thermal stability to oxidation are the principals characteristics to assure these quality exigencies. The use of additives is the methods most used for establish the quality for international specification. The incorporation of heavy crude oils in mixtures to produce fuels has caused a diminution of the quality of the derivatives produced. High viscosity, density and high sulfur content in the heavy crude oils affect some of properties of the jet fuel, influencing in its composition, increasing the mercaptanes and total sulfur content, getting a jet fuel unstable, with low conductivity and highly corrosive. So, for obtain the quality required internationally is necessary use additives. This paper study how the heavy crude oils affect the conductivity and the thermal stability of the jets fuels type Jet A1. Also analyze of the use of dissipater electrostatic and antioxidants additives, to improve these properties in the jet fuel. (author)

7 CFR 30.20 - Crude.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Crude. 30.20 Section 30.20 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... unfinished as a result of extreme immaturity. Crude tobacco ordinarily has a characteristic green color. ...

How much crude oil can zooplankton ingest? Estimating the quantity of dispersed crude oil defecated by planktonic copepods

DEFF Research Database (Denmark)

Almeda, Rodrigo; Connelly, Tara L.; Buskey, Edward J.

2016-01-01

% of the analyzed fecal pellets from three species of copepods and a natural copepod assemblage exposed for 48 h to physically or chemically dispersed light crude oil contained crude oil droplets. Crude oil droplets inside fecal pellets were smaller (median diameter: 2.4-3.5 mu m) than droplets in the physically...

Artificial Intelligence for Inferential Control of Crude Oil Stripping Process

Directory of Open Access Journals (Sweden)

Mehdi Ebnali

2018-01-01

Full Text Available Stripper columns are used for sweetening crude oil, and they must hold product hydrogen sulfide content as near the set points as possible in the faces of upsets. Since product    quality cannot be measured easily and economically online, the control of product quality is often achieved by maintaining a suitable tray temperature near its set point. Tray temperature control method, however, is not a proper option for a multi-component stripping column because the tray temperature does not correspond exactly to the product composition. To overcome this problem, secondary measurements can be used to infer the product quality and adjust the values of the manipulated variables. In this paper, we have used a novel inferential control approach base on adaptive network fuzzy inference system (ANFIS for stripping process. ANFIS with different learning algorithms is used for modeling the process and building a composition estimator to estimate the composition of the bottom product. The developed estimator is tested, and the results show that the predictions made by ANFIS structure are in good agreement with the results of simulation by ASPEN HYSYS process simulation package. In addition, inferential control by the implementation of ANFIS-based online composition estimator in a cascade control scheme is superior to traditional tray temperature control method based on less integral time absolute error and low duty consumption in reboiler.

7 CFR 29.1010 - Crude.

Science.gov (United States)

2010-01-01

... of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 92) § 29.1010 Crude. A subdegree of maturity. Crude leaves are usually hard and slick as a result of extreme immaturity. A similar condition may result from fire-kill, sunburn, or sunscald. Any leaf...

7 CFR 29.3512 - Crude.

Science.gov (United States)

2010-01-01

... of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 95) § 29.3512 Crude. A subdegree of maturity. Crude leaves are usually hard and slick as a result of extreme immaturity. A similar condition may result from firekill, sunburn, or sunscald. Any leaf...

7 CFR 29.2261 - Crude.

Science.gov (United States)

2010-01-01

... of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing.... A subdegree of maturity. Crude leaves are usually hard and slick as a result of extreme immaturity. A similar condition may result from fire-kill, sunburn, or sunscald. Any leaf which is crude to the...

Application of microbiological methods for secondary oil recovery from the Carpathian crude oil reservoirs

Energy Technology Data Exchange (ETDEWEB)

Karaskiewicz, J

1974-01-01

The investigation made it possible to isolate from different ecologic environmental (soil, crude oil, formation water, industrial wastes) bacteria cultures of the genus Arthrobacter, Clostridium, Mycobacterium, Peptococcus, and Pseudomonas. These heterotrophic bacteria are characterized by a high metabolic and biogeochemical activity hydrocarbon transformation. Experiments on a technical scale were conducted from 1961 to 1971 in 20 wells; in this study, only the 16 most typical examples are discussed. The experiments were conducted in Carpathian crude oil reservoirs. To each well, a 500:1 mixture of the so-called bacteria vaccine (containing an active biomass of cultures obtained by a specific cultivation method and holding 6 x 10/sup 5/ bacteria cells in 1 ml of fluid, 2,000 kg of molasses, and 50 cu m of water originating from the reservoir submitted to treatment) was injected at 500 to 1,200 m. The intensification of the microbiological processes in the reservoir was observed. This phenomenon occurred not only in the wells to which the bacteria vaccine was injected, but also in the surrounding producing wells. At the same time, an increase in the crude oil production occurred on the average within the range from 20 to 200% and the surpluses of crude oil production continued for 2 to 8 yr. (92 refs.)

Investigating the influence of pressure and temperature on malaysian crude oil density and viscosity for improved recovery

International Nuclear Information System (INIS)

Zahoor, M.K.; Derahman, M.N.

2012-01-01

Malaysia has great potential as a crude oil or fossil fuel producing country. To increase oil production, behavior of Malaysian Crude Oil has been analyzed with reference to temperature and pressure variations. The effect of these parameters on crude oil density and viscosity has been observed, to select the methodology to be adopted for increases recovery by implementing enhanced oil recovery (EOR) project. Based on this study it has been decided to further explore the feasibility of increasing reservoir pressure. (author)

Systemic toxicity of dermally applied crude oils in rats

Energy Technology Data Exchange (ETDEWEB)

Feuston, M.H.; Mackerer, C.R.; Schreiner, C.A.; Hamilton, C.E. [Stonybrook Labs., Inc., Princeton, NJ (United States)

1997-12-31

Two crude oils, differing in viscosity (V) and nitrogen (N) and sulfur (S) content, were evaluated for systemic toxicity, In the Crude I (low V, low N, low S) study, the material was applied to the clipped backs of rats at dose levels of 0, 30, 125, and 500 mg/kg. In the Crude II (high V, high N, moderate S) study, the oil was applied similarly at the same dose levels. The crude oils were applied for 13 wk, 5 d/wk. Exposure sites were not occluded. Mean body weight gain (wk 1-14) was significantly reduced in male rats exposed to Crude II; body weight gain of all other animals was not adversely affected by treatment. An increase in absolute (A) and relative (R) liver weights and a decrease in A and R thymus weights were observed in male and female rats exposed to Crude II at 500 mg/kg; only liver weights (A and R) were adversely affected in male and female rats exposed to Crude I. In general, there was no consistent pattern of toxicity for serum chemistry endpoints; however, more parameters were adversely affected in Crude II-exposed female rats than in the other exposed groups. A consistent pattern of toxicity for hematology endpoints was observed among male rats exposed to Crude I and male and female rats exposed to Crude II. Parameters affected included: Crudes I and II, red blood cell count, hemoglobin, and hematocrit, Crude II, platelet count. Microscopic evaluation of tissues revealed the following treatment-related findings: Crude I, treated skin, thymus, and thyroid; Crude II, bone marrow, treated skin, thymus, and thyroid. The LOEL (lowest observable effect level) for skin irritation and systemic toxicity (based on marginal effects on the thyroid) for both crude oils was 30 mg/kg; effects were more numerous and more pronounced in animals exposed to Crude II. Systemic effects are probably related to concentrations of polycyclic aromatic compounds (PAC) found in crude oil.

Assessing an effective feeding strategy to optimize crude glycerol utilization as sustainable carbon source for lipid accumulation in oleaginous yeasts.

Science.gov (United States)

Signori, Lorenzo; Ami, Diletta; Posteri, Riccardo; Giuzzi, Andrea; Mereghetti, Paolo; Porro, Danilo; Branduardi, Paola

2016-05-05

Microbial lipids can represent a valuable alternative feedstock for biodiesel production in the context of a viable bio-based economy. This production can be driven by cultivating some oleaginous microorganisms on crude-glycerol, a 10% (w/w) by-product produced during the transesterification process from oils into biodiesel. Despite attractive, the perspective is still economically unsustainable, mainly because impurities in crude glycerol can negatively affect microbial performances. In this view, the selection of the best cell factory, together with the development of a robust and effective production process are primary requirements. The present work compared crude versus pure glycerol as carbon sources for lipid production by three different oleaginous yeasts: Rhodosporidium toruloides (DSM 4444), Lipomyces starkeyi (DSM 70295) and Cryptococcus curvatus (DSM 70022). An efficient yet simple feeding strategy for avoiding the lag phase caused by growth on crude glycerol was developed, leading to high biomass and lipid production for all the tested yeasts. Flow-cytometry and fourier transform infrared (FTIR) microspectroscopy, supported by principal component analysis (PCA), were used as non-invasive and quick techniques to monitor, compare and analyze the lipid production over time. Gas chromatography (GC) analysis completed the quali-quantitative description. Under these operative conditions, the highest lipid content (up to 60.9% wt/wt) was measured in R. toruloides, while L. starkeyi showed the fastest glycerol consumption rate (1.05 g L(-1) h(-1)). Being productivity the most industrially relevant feature to be pursued, under the presented optimized conditions R. toruloides showed the best lipid productivity (0.13 and 0.15 g L(-1) h(-1) on pure and crude glycerol, respectively). Here we demonstrated that the development of an efficient feeding strategy is sufficient in preventing the inhibitory effect of crude glycerol, and robust enough to ensure high lipid

Environmental drivers of differences in microbial community structure in crude oil reservoirs across a methanogenic gradient

Directory of Open Access Journals (Sweden)

Jenna L Shelton

2016-09-01

Full Text Available Stimulating in situ microbial communities in oil reservoirs to produce natural gas is a potentially viable strategy for recovering additional fossil fuel resources following traditional recovery operations. Little is known about what geochemical parameters drive microbial population dynamics in biodegraded, methanogenic oil reservoirs. We investigated if microbial community structure was significantly impacted by the extent of crude oil biodegradation, extent of biogenic methane production, and formation water chemistry. Twenty-two oil production wells from north central Louisiana, USA, were sampled for analysis of microbial community structure and fluid geochemistry. Archaea were the dominant microbial community in the majority of the wells sampled. Methanogens, including hydrogenotrophic and methylotrophic organisms, were numerically dominant in every well, accounting for, on average, over 98% of the total archaea present. The dominant Bacteria groups were Pseudomonas, Acinetobacter, Enterobacteriaceae, and Clostridiales, which have also been identified in other microbially-altered oil reservoirs. Comparing microbial community structure to fluid (gas, water, and oil geochemistry revealed that the relative extent of biodegradation, salinity, and spatial location were the major drivers of microbial diversity. Archaeal relative abundance was independent of the extent of methanogenesis, but closely correlated to the extent of crude oil biodegradation; therefore, microbial community structure is likely not a good sole predictor of methanogenic activity, but may predict the extent of crude oil biodegradation. However, when the shallow, highly biodegraded, low salinity wells were excluded from the statistical analysis, no environmental parameters could explain the differences in microbial community structure. This suggests that the microbial community structure of the 5 shallow up-dip wells was different than the 17 deeper, down-dip wells, and that

Multi-objective model of waste transportation management for crude palm oil industry

Science.gov (United States)

Silalahi, Meslin; Mawengkang, Herman; Irsa Syahputri, Nenna

2018-02-01

The crude palm oil industry is an agro-industrial commodity. The global market of this industry has experienced rapid growth in recent years, such that it has a strategic value to be developed for Indonesian economy. Despite these economic benefits there are a number of environmental problems at the factories, such as high water consumption, the generation of a large amount of wastewater with a high organic content, and the generation of a large quantity of solid wastes and air pollution. In terms of waste transportation, we propose a multiobjective programming model for managing business environmental risk in a crude palm oil manufacture which gives the best possible configuration of waste management facilities and allocates wastes to these facilities. Then we develop an interactive approach for tackling logistics and environmental risk production planning problem for the crude palm oil industry.

Research on crude oil storage and transportation based on optimization algorithm

Science.gov (United States)

Yuan, Xuhua

2018-04-01

At present, the optimization theory and method have been widely used in the optimization scheduling and optimal operation scheme of complex production systems. Based on C++Builder 6 program development platform, the theoretical research results are implemented by computer. The simulation and intelligent decision system of crude oil storage and transportation inventory scheduling are designed. The system includes modules of project management, data management, graphics processing, simulation of oil depot operation scheme. It can realize the optimization of the scheduling scheme of crude oil storage and transportation system. A multi-point temperature measuring system for monitoring the temperature field of floating roof oil storage tank is developed. The results show that by optimizing operating parameters such as tank operating mode and temperature, the total transportation scheduling costs of the storage and transportation system can be reduced by 9.1%. Therefore, this method can realize safe and stable operation of crude oil storage and transportation system.

From crude glycerol to carotenoids by using a Rhodotorula glutinis mutant.

Science.gov (United States)

Cutzu, Raffaela; Coi, Annalisa; Rosso, Fulvia; Bardi, Laura; Ciani, Maurizio; Budroni, Marilena; Zara, Giacomo; Zara, Severino; Mannazzu, Ilaria

2013-06-01

In this work eighteen red yeasts were screened for carotenoids production on glycerol containing medium. Strain C2.5t1 of Rhodotorula glutinis, that showed the highest productivity, was UV mutagenized. Mutant 400A15, that exhibited a 280 % increase in β-carotene production in respect to the parental strain, was selected. A central composite design was applied to 400A15 to optimize carotenoids and biomass productions. Regression analyses of the quadratic polynomial equations obtained (R(2) = 0.87 and 0.94, for carotenoids and biomass, respectively) suggest that the models are reliable and significant (P < 0.0001) in the prediction of carotenoids and biomass productions on the basis of the concentrations of crude glycerol, yeast extract and peptone. Accordingly, total carotenoids production achieved (14.07 ± 1.45 mg l(-1)) under optimized growth conditions was not statistically different from the maximal predicted (14.64 ± 1.57 mg l(-1)) (P < 0.05), and it was about 100 % higher than that obtained under un-optimized conditions. Therefore mutant 400A15 may represent a biocatalyst of choice for the bioconversion of crude glycerol into value-added metabolites, and a tool for the valorization of this by-product of the biodiesel industry.

Valorization of crude glycerol and eggshell biowaste as media components for hydrogen production: A scale-up study using co-culture system.

Science.gov (United States)

Pachapur, Vinayak Laxman; Das, Ratul Kumar; Brar, Satinder Kaur; Le Bihan, Yann; Buelna, Gerardo

2017-02-01

The properties of eggshells (EGS) as neutralizing and immobilizing agent were investigated for hydrogen (H 2 ) production using crude glycerol (CG) by co-culture system. Eggshells of different sizes and concentrations were used during batch and repeated-batch fermentation. For batch and repeated-batch fermentation, the maximum H 2 production (36.53±0.53 and 41.16±0.95mmol/L, respectively) was obtained with the EGS size of 33μmcomponents, the EGS concentration of 0.25% (w/v) was found to be optimum for maximum H 2 production (31.66±0.55mmol/L) and the production profile was comparable to H 2 production (32.07±0.92mmol/L) obtained with all media components. In scale-up study with semi-continuous bioreactor (7.5L), almost 1.5-fold increase (in comparison to mono-culture) i.e. 312.12mmol-H 2 /L-of medium with 86.65% glycerol utilization was obtained. Copyright © 2016 Elsevier Ltd. All rights reserved.

DOE/DOT Crude Oil Characterization Research Study, Task 2 Test Report on Evaluating Crude Oil Sampling and Analysis Methods

Energy Technology Data Exchange (ETDEWEB)

Lord, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Allen, Ray [Allen Energy Services, Inc., Longview, TX (United States); Rudeen, David [GRAM, Inc., Albuquerque, NM (United States)

2017-11-01

The Crude Oil Characterization Research Study is designed to evaluate whether crude oils currently transported in North America, including those produced from "tight" formations, exhibit physical or chemical properties that are distinct from conventional crudes, and how these properties associate with combustion hazards with may be realized during transportation and handling.

Anaerobic co-digestion cassava wastewater and crude glycerin for removal of COD and solid; Co-digestao anaerobica de manipueira e glicerina bruta para remocao de DQO e solidos

Energy Technology Data Exchange (ETDEWEB)

Silva, Jefferson L.G.; Guerra Junior, Joao B. [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil)], E-mail: j.lg11@yahoo.com.br; Gomes, Simone D.; Mallmann, Larissa S. [Universidade Estadual do Oeste do Parana (CCET/PGEAGRI/UNIOESTE), Cascavel, PR (Brazil). Dept. de Recursos Hidricos e Saneamento Ambiental

2012-11-01

To be discarded into the environment, cassava wastewater, generated during the processing of the cassava root, needs to be dealt with trying to reduce its organic load and total solids, harmful to water bodies. As for crude glycerin, a byproduct of biodiesel production, need alternatives to its destination, because the cost to its purification is often not feasible, preventing its use by pharmaceutical and food industries. In this study we chose to anaerobic digestion to treat manipueira assessing the behavior of the reactor with the addition of glycerin. The reactor was constructed of PVC with 60cm long, 20cm in diameter and a volume of 8.38 L, and HRT was 5 days. Three treatments were applied: T1, only manipueira, T2 with 0.25% glycerol and T3, with 0.50%. The three treatments showed a great reduction of organic load (above 90%) and higher with the addition of 0.25% crude glycerine. The highest mean removal of solids and total volatile solids occurred in treatment with 0.50% crude glycerine, being 84.18% and 91.41% respectively. (author)

Rhamnolipid produced by Pseudomonas aeruginosa USM-AR2 facilitates crude oil distillation.

Science.gov (United States)

Asshifa Md Noh, Nur; Al-Ashraf Abdullah, Amirul; Nasir Mohamad Ibrahim, Mohamad; Ramli Mohd Yahya, Ahmad

2012-01-01

A biosurfactant-producing and hydrocarbon-utilizing bacterium, Pseudomonas aeruginosa USM-AR2, was used to assist conventional distillation. Batch cultivation in a bioreactor gave a biomass of 9.4 g L(-1) and rhamnolipid concentration of 2.4 g L(-1) achieved after 72 h. Biosurfactant activity (rhamnolipid) was detected by the orcinol assay, emulsification index and drop collapse test. Pretreatment of crude oil TK-1 and AG-2 with a culture of P. aeruginosa USM-AR2 that contains rhamnolipid was proven to facilitate the distillation process by reducing the duration without reducing the quality of petroleum distillate. It showed a potential in reducing the duration of the distillation process, with at least 2- to 3-fold decreases in distillation time. This is supported by GC-MS analysis of the distillate where there was no difference between compounds detected in distillate obtained from treated or untreated crude oil. Calorimetric tests showed the calorie value of the distillate remained the same with or without treatment. These two factors confirmed that the quality of the distillate was not compromised and the incubation process by the microbial culture did not over-degrade the oil. The rhamnolipid produced by this culture was the main factor that enhanced the distillation performance, which is related to the emulsification of hydrocarbon chains in the crude oil. This biotreatment may play an important role to improve the existing conventional refinery and distillation process. Reducing the distillation times by pretreating the crude oil with a natural biosynthetic product translates to energy and cost savings in producing petroleum products.

Penggunaan H-Zeolit dan Tawas dalam Pemurnian Crude Glycerol dengan Proses Adsorpsi dan Koagulasi

OpenAIRE

Isalmi Aziz, M.T; Nur Hijjah Bayani Fadhilah; Hendrawati Hendrawati

2017-01-01

Production of biodiesel from used cooking oil byproducts such as crude glycerol with low purity. The crude glycerol containing compounds impurities such as free fatty acids, alcohol, soap, catalyst and water. Compound adsorption of impurities can be done with the H-zeolite as adsorbent, but the resulting quality is still not good. To improve its quality, this research was added alum (coagulation) process so that the adsorption of colloidal-sized compound impurities which can be separated from...

Penggunaan H-Zeolit Dan Tawas Dalam Pemurnian Crude Glycerol Dengan Proses Adsorpsi Dan Koagulasi

OpenAIRE

Aziz, M.T, Isalmi; Fadhilah, Nur Hijjah Bayani; Hendrawati, Hendrawati

2017-01-01

Production of biodiesel from used cooking oil byproducts such as crude glycerol with low purity. The crude glycerol containing compounds impurities such as free fatty acids, alcohol, soap, catalyst and water. Compound adsorption of impurities can be done with the H-zeolite as adsorbent, but the resulting quality is still not good. To improve its quality, this research was added alum (coagulation) process so that the adsorption of colloidal-sized compound impurities which can be separated from...

Biosurfactant and enzyme mediated crude oil degradation by Pseudomonas stutzeri NA3 and Acinetobacter baumannii MN3.

Science.gov (United States)

Parthipan, Punniyakotti; Elumalai, Punniyakotti; Sathishkumar, Kuppusamy; Sabarinathan, Devaraj; Murugan, Kadarkarai; Benelli, Giovanni; Rajasekar, Aruliah

2017-10-01

The present study focuses on the optimization of biosurfactant (BS) production using two potential biosurfactant producer Pseudomonas stutzeri NA3 and Acinetobacter baumannii MN3 and role of enzymes in the biodegradation of crude oil. The optimal conditions for P. stutzeri NA3 and A. baumannii MN3 for biodegradation were pH of 8 and 7; temperature of 30 and 40 °C, respectively. P. stutzeri NA3 and A. baumannii MN3 produced 3.81 and 4.68 g/L of BS, respectively. Gas chromatography mass spectrometry confirmed that BS was mainly composed of fatty acids. Furthermore, the role of the degradative enzymes, alkane hydroxylase, alcohol dehydrogenase and laccase on biodegradation of crude oil are explained. Maximum biodegradation efficiency (BE) was recorded for mixed consortia (86%) followed by strain P. stutzeri NA3 (84%). Both bacterial strains were found to be vigorous biodegraders of crude oil than other biosurfactant-producing bacteria due to their enzyme production capabilities and our results suggests that the bacterial isolates can be used for effective degradation of crude oil within short time periods.

Preparation of progenin III from total steroidal saponins of Dioscorea nipponica Makino using a crude enzyme from Aspergillus oryzae strain.

Science.gov (United States)

Liu, Tingqiang; Yu, Hongshan; Liu, Chunying; Bao, Yongming; Hu, Xiangchun; Wang, Yuanhao; Liu, Bing; Fu, Yaoyao; Tang, Sihui; Jin, Fengxie

2013-05-01

Progenin III, one of the most active spirostanol saponins, is a potential candidate for anti-cancer therapy due to its strong antitumor activity and low hemolytic activity. However, the concentration of progenin III is extremely low in natural Dioscorea plants. In this paper, the progenin III production from total steroidal saponins of Dioscorea nipponica Makino was studied using the crude enzyme from Aspergillus oryzae DLFCC-38. The crude enzyme converting total steroidal saponins into progenin III was obtained from the A. oryzae DLFCC-38 culture. For enzyme production, the strain was cultured for 72 h at 30 °C with shaking at 150 rpm in 5 % (w/v) malt extract medium containing 2 % (v/v) extract of D. nipponica as the enzyme inducer. The crude enzyme converted total steroidal saponins into major progenin III with a high yield when the reaction was carried out for 9 h at 50 °C and pH 5.0 with the 20 mg/ml of substrate. In the preparation of progenin III, 117 g of crude progenin III was obtained from 160 g of substrate, and the crude product was purified with silica gel column to obtain 60.3 g progenin III of 93.4 % purity.

The energy efficiency of crude oil refining in Brazil: A Brazilian refinery plant case

International Nuclear Information System (INIS)

Lima, Romulo S. de; Schaeffer, Roberto

2011-01-01

This article evaluates energy efficiency in Brazilian crude oil refining in comparison with the crude oil refining in the United States between 1930 and 2008. It aims to show that increased refinery complexity reduces the energy consumption of products of high value added. Moreover, the article shows that improvements in energy efficiency result in higher quality products and increased processing of oil. A Brazilian refinery with a capacity of 157,000 barrels per day (kbpd) was modernized in 2008 at a cost of US $1.3 billion. As a result, its capacity increased by 17%, from 157 to 189 kbpd. Its complexity index also rose from 3.2 to 6.8, allowing an improvement in the EII (energy intensity index) from 110% to 93%. In relation to the crude oil processed before being modernized, energy consumption fell from 0.75 to 0.52 MBtu (million British thermal units) per barrel processed. These proceedings show that increases in complexity reduce the energy consumed in the production of final products with high value added, such as gasoline, diesel and jet fuel. -- Highlights: → Increased refinery complexity reduces the energy consumption of products of high value added. → Improvements in refinery energy efficiency result in higher quality products and increased processing of oil. → Brazilian refineries were not affected significantly in the 2008 crisis, such as the US refineries, due to many factors. → The EII of Brazilian refining presents real opportunities for gains through changes in the profile of energy consumed.

Crossbreeding to increase beef production: additive and non ...

African Journals Online (AJOL)

GScholtz

2013-06-06

Jun 6, 2013 ... Crossbreeding to increase beef production: additive and non-additive effects on weight traits ... total weight of weaned calves. ... Weight traits are not all equally important to efficiency ... values to model total herd productivity. ..... The maintenance requirement of a cow is affected by her weight: the larger the.

Volatility spillover between crude oil and exchange rate: A copula-CARR approach

Science.gov (United States)

Pu, Y. J.; Guo, M. Y.

2017-11-01

Oil provides a powerful impetus for modern society's production and life. The influences of oil price fluctuations on socio-economic development are obvious, and it draws more attention from scholars. However, the distribution of oil is highly centralized, which leads to the vast majority of oil trading through foreign trade. As a result, exchange rate plays an important role in the oil business. Study on the relationship between exchange rate and crude oil gradually becomes a hot research topic in recent years. In this paper, we use copula and CARR model to study correlation structure and relationship between crude oil price and exchange rate. We establish CARR models as marginal models and use five copulas which are Gaussian Copula, Student-t Copula, Gumbel Copula, Clayton Copula and Frank Copula to study the correlation structure between NYMEX crude oil price range and U. S. Dollar Index range. Furthermore, we use Copula-CARR model with structural breaks to detect the change points in the correlation structure between NYMEX crude oil price range and U. S. Dollar Index range. Empirical results show that the change points are closely related to the actual economic events.

Application of Markov Model in Crude Oil Price Forecasting

Directory of Open Access Journals (Sweden)

Nuhu Isah

2017-08-01

Full Text Available Crude oil is an important energy commodity to mankind. Several causes have made crude oil prices to be volatile. The fluctuation of crude oil prices has affected many related sectors and stock market indices. Hence, forecasting the crude oil prices is essential to avoid the future prices of the non-renewable natural resources to rise. In this study, daily crude oil prices data was obtained from WTI dated 2 January to 29 May 2015. We used Markov Model (MM approach in forecasting the crude oil prices. In this study, the analyses were done using EViews and Maple software where the potential of this software in forecasting daily crude oil prices time series data was explored. Based on the study, we concluded that MM model is able to produce accurate forecast based on a description of history patterns in crude oil prices.

Cu determination in crude oil distillation products by atomic absorption and inductively coupled plasma mass spectrometry after analyte transfer to aqueous solution

Science.gov (United States)

Kowalewska, Zofia; Ruszczyńska, Anna; Bulska, Ewa

2005-03-01

Cu was determined in a wide range of petroleum products from crude oil distillation using flame atomic absorption spectrometry (FAAS), electrothermal atomic absorption spectrometry (ETAAS) and inductively coupled plasma mass spectrometry (ICP-MS). Different procedures of sample preparation were evaluated: (i) mineralization with sulfuric acid in an open system, (ii) mineralization in a closed microwave system, (iii) combustion in hydrogen-oxygen flame in the Wickbold's apparatus, (iv) matrix evaporation followed by acid dissolution, and (v) acidic extraction. All the above procedures led to the transfer of the analyte into an aqueous solution for the analytical measurement step. It was found that application of FAAS was limited to the analysis of the heaviest petroleum products of high Cu content. In ICP-MS, the use of internal reference method (with Rh or In as internal reference element) was required to eliminate the matrix effects in the analysis of extracts and the concentrated solutions of mineralized heavy petroleum products. The detection limits (in original samples) were equal to, respectively, 10, 86, 3.3, 0.9 and 0.4 ng g - 1 in procedures i-v with ETAAS detection and 10, 78, 1.1 and 0.5 ng g - 1 in procedures i-iii and v with ICP-MS detection. The procedures recommended here were validated by recovery experiments, certified reference materials analysis and comparison of results, obtained for a given sample, in different ways. The Cu content in the analyzed samples was: 50-110 ng g - 1 in crude oil, oil, oil and 140-300 ng g - 1 in distillation residue.

Spectrometric methods for the determination of chlorine in crude oil and petroleum derivatives — A review

International Nuclear Information System (INIS)

Doyle, Adriana; Saavedra, Alvaro; Tristão, Maria Luiza B.; Mendes, Luiz A.N.; Aucélio, Ricardo Q.

2013-01-01

Chlorine determination in crude oil is made in order to guarantee that the oil does not contain levels of this element that might cause damages in the oil processing equipment. In petroleum products, the determination of chlorine is made, for instance, to evaluate if there are proper concentrations of organochloride compounds, which are used as additives. Such determinations are currently performed following official guidelines from the ASTM International and from the United States Environmental Protection Agency as well as protocols indicated by the Universal Oil Products. X-ray fluorescence spectroscopy plays an important role in many of these official methods. In contrast, other spectrometric methods based on optical and mass detection are plagued by limitations related to both the fundamental characteristics of non-metals and to the complex sample matrices, which reflects in the small number of articles devoted to these applications. In this review, the current status of the spectrometric methods, especially the role played by X-ray fluorescence spectrometry, is evaluated in terms of the determination of chlorine in crude oil and petroleum derivatives. Comparison of the performance of the methods, limitations and potential new approaches to ensure proper spectrometric determinations of chlorine is indicated. - Highlights: • Critical evaluation of spectrometric methods for chlorine in petroleum products. • Reviews on element determination in petroleum have not address the case of chlorine. • Peculiarities of the spectrometric determination of Cl in petroleum are discussed. • The spectrometric approaches are detailed and compared to the official methods. • New trends in chlorine determination in petroleum products are indicated

An analysis of the additional fission product release phenomena

International Nuclear Information System (INIS)

Takeda, Tsuneo; Nagai, Hitoshi

1978-09-01

The additional fission product release behavior through a defect hole on the cladding of fuel rods has been studied qualitatively with a computer program CODAC-ARFP. The additional fission product release phenomena are described as qualitative evaluation. The additional fission product release behavior in coolant temperature and pressure fluctuations and in reactor start-up and shut-down depends on coolant water flow behavior into and from the free space of fuel rods through a defect hole. Based on the results of evaluations, the experimental results with an inpile water loop OWL-1 are described in detail. The estimation methods of fission product quantity in the free space and fission product release ratio (quantity released into the coolant/quantity in the free space before beginning of release) are necessary for analysis of the fission product release behavior; the estimation method of water flow through a defect hole is also necessary. In development of the above estimation methods, outpile and capsule experiments supporting the additional fission product release experiments are required. (author)

Laboratory Evaluation of the Anti-stain Efficacy of Crude Wood Vinegar for Pinus densiflora

Directory of Open Access Journals (Sweden)

Sabiha Salim

2016-12-01

Full Text Available In Korea, Pinus densiflora is one of the most important indigenous tree species in terms of making high-value wood products. Therefore, Korean sawmills exercise extreme caution to prevent fungal discoloration such as that caused by sapstains and molds on the timber. In this study, the effectiveness of using natural crude wood vinegar to inhibit sapstains and molds, especially on Pinus densiflora (Japanese red pine was examined. Pinus densiflora wood samples were dipped in absolute and diluted wood vinegar at different concentrations (1:1, 2:1, and 3:1; deionized water to wood vinegar dilution ratio for 3 minutes and immediately air-dried. In addition, volatile wood vinegar was also used in this study to imitate the condition of wood vinegar when exposed to open air. The degree of discoloration was examined and evaluated every 2, 4, 6, and 8 weeks according to the ASTM D4445-91 Standard Method for laboratory test. Crude wood vinegar inhibited sapstains more efficiently than it inhibited molds. Wood vinegar at a 1:1 concentration was found to be the most optimum treatment for inhibiting sapstains for at least 8 weeks.

Radiation-induced desulfurization of Arabian crude oil and straight-run diesel

International Nuclear Information System (INIS)

Basfar, A.A.; Mohamed, K.A.

2011-01-01

Radiation-induced desulfurization of four types of Arabian crude oils (heavy, medium, light and extra light) and straight-run diesel (SRD) was investigated over the range of 10-200 kGy. Results show that gamma radiation processing at absorbed doses up to 200 kGy without further treatment is not sufficient for desulfurization. However, the combination of gamma-irradiation with other physical/chemical processes (i.e. L/L extraction, adsorption and oxidation) may be capable of removing considerable levels of sulfur compounds in the investigated products. Currently, this approach of combined radiation/physical/chemical processes is under investigation. The findings of these attempts will be reported in the future. - Highlights: → Irradiation effect on desulfurization in Arabian crude oils and straight-run diesel was investigated. → No noticeable changes in sulfur content after irradiation up to 200 kGy were observed. → Stricter regulations on sulfur levels in fuels motivate search for improved desulfurization processes. → Limited investigations on radiation-induced desulfurization of oil products are conducted.

Coals to Newcastle: Will Alberta become a crude oil importer?

International Nuclear Information System (INIS)

Haessel, W.; Foley, D.J.

1991-01-01

The security of markets for Canadian heavy crude oil (HCO) under different conditions is examined. The emphasis of the study is on the conditions under which bitumen blend from Alberta could penetrate certain markets that have generally been identified as potential prospects. A secondary question concerns the cost reductions in bitumen production and upgrading that would be needed for bitumen blend and synthetic crude oil (SCO) to penetrate these same markets if long-term oil prices settle at US$18/bbl for Saudi light delivered to the USA Gulf Coast in 2010. A brief overview is first presented of some of the world and US factors that will affect the demand for Canadian HCO, with specific reference to the demand in the northern USA in 2010. The determination of the volume of HCO that can or will be processed at a refinery or a combination of refineries in a given market is then discussed. The cost and volume numbers for 2010 as provided in the National Energy Board's latest Canadian energy supply and demand forecast are used in the analysis. It is concluded that all traditional markets outside of the Canadian prairies could be lost if world oil prices stay below US$18/bbl for extended periods. At prices below US$17/bbl, bitumen producers would have trouble competing with imported crude oils in Edmonton unless bitumen production costs decline from current levels. The potential for bitumen production costs to decline enough for diluted bitumen to compete with US$18/bbl oil is better than the prospect for SCO costs to decrease enough to compete in eastern Canada or the northern USA at those price levels. 9 figs., 8 tabs

Naphthenic acid characterization and distribution in crude oils; Caracterizacao e distribuicao de acidos naftenicos em petroleos

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, Regina C.L.; Gomes, Alexandre de O. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2008-07-01

Naphthenic acid corrosion was observed for the first time during the distillation process of some kind of crude oils in 1920. Recent reports about naphthenic acid corrosion have been found in China, India, Venezuela, Eastern Europe, Russia and the USA. In Brazil, heavy and acid crude oil processing is rising. Some brazilian crude oils have TAN around 3,0 mg KOH/g. The presence of relatively high levels of naphthenic acids in crude oils is a bane of petroleum refiners; and more recently, of producers as well, who have reported problems during production with calcium and sodium naphthenate . Essentially, these acids which are found to greater or lesser extent in virtually all crude oils are corrosive and tend to cause equipment failures, lead to high maintenance costs and may pose environmental disposal problems. In order to give these information to PETROBRAS, The Research and Development Center of PETROBRAS (CENPES) has been working in house and with brazilian universities developing analytical technicians to know better molecular structures and distribution of these acids compounds in crude oils. This work presents the actual methods and some results from these developments. (author)

Polyhydroxyalkanoates (PHA) production from fermented crude glycerol: Study on the conversion of 1,3-propanediol to PHA in mixed microbial consortia

DEFF Research Database (Denmark)

Burniol Figols, Anna; Varrone, Cristiano; Daugaard, Anders Egede

2018-01-01

Crude glycerol, a by-product from the biodiesel industry, can be converted by mixed microbial consortia into 1,3-propanediol (1,3-PDO) and volatile fatty acids. In this study, further conversion of these main products into polyhydroxyalkanoates (PHA) was investigated with the focus on 1,3-PDO. Two...... different approaches for the enrichment of PHA accumulating microbial consortia using an aerobic dynamic feeding strategy were applied. With the first approach, where nitrogen was present during the whole cycle, no net production of PHA from 1,3-PDO was observed in the fermented effluent, not even...... the storage response. Nitrogen was still supplied during the famine phase. With the latter strategy, a net production of PHA from 1,3-PDO was observed at a yield of 0.24 Cmol PHA/Cmol 1,3-PDO. The overall yield from the fermented effluent was 0.42 Cmol PHA/Cmol substrate. Overall, the PHA yield from 1,3-PDO...

The impact of environmental regulations on United States crude oil supplies

International Nuclear Information System (INIS)

Godec, M.L.; Biglarbigi, K.

1991-01-01

A number of legislative and regulatory initiatives being considered to protect the environment could affect the economics of oil and gas exploration and production (E and P) in the Unites States. This paper summarizes the results of a comprehensive assessment of the potential cumulative energy and economic impacts of environmental regulatory initiatives on United States crude oil supplies. The results of the analysis clearly will determine the level of impact, but the results show that significant impacts are felt over a wide range of regulations, over a wide range of crude oil prices, and at two levels of development for extraction technologies. The regulations evaluated all have an impact on all resource categories analyzed in the study

Application of a novel enzymatic pretreatment using crude hydrolytic extracellular enzyme solution to microalgal biomass for dark fermentative hydrogen production.

Science.gov (United States)

Yun, Yeo-Myeong; Kim, Dong-Hoon; Oh, You-Kwan; Shin, Hang-Sik; Jung, Kyung-Won

2014-05-01

In this study, a novel enzymatic pretreatment of Chlorella vulgaris for dark fermentative hydrogen production (DFHP) was performed using crude hydrolytic extracellular enzyme solution (CHEES) extracted from the H2 fermented effluent of food waste. It was found that the enzyme extracted at 52 h had the highest hydrolysis efficiency of microalgal biomass, resulting in the highest H2 yield of 43.1 mL H2/g dry cell weight along with shorter lag periods. Even though a high amount of VFAs was accumulated in CHEES, especially butyrate, the fermentative bacteria on the DFHP was not affected from product inhibition. It also appears that the presence of organic acids, especially lactate and acetate, contained in the CHEES facilitated enhancement of H2 production acted as a co-substrate. Therefore, all of the experimental results suggest that the enhancement of DFHP performance caused by CHEES has a dual role as the hydrolysis enhancer and the co-substrate supplier. Copyright © 2014 Elsevier Ltd. All rights reserved.

Price volatility, hedging and variable risk premium in the crude oil market

International Nuclear Information System (INIS)

Ahmad Jalali-Naini; Maryam Kazemi Manesh

2006-01-01

The crude oil price exhibits a high degree of volatility which varies significantly over time. Such characteristics imply that the oil market is a promising area for testing volatility models. Testing and predicting volatility using ARCH and GARCH models have grown in the literature. A useful application of the volatility models is in the formulation of hedging strategies. In this paper we compare the optimal hedge ratio for the crude oil using the classical minimum risk approach and use ARCH to incorporate the effect of heteroskedasticity in the residuals on the hedge ratio. In addition, we test for the existence of a variable risk premium in the crude oil market. We find that, assuming rational expectations, there is a non-zero risk premium. We test for the variability of the risk premia and find evidence in its support when we employed a multivariate GARCH model. (author)

Basic properties of crude rubber seed oil and crude palm oil blend as a potential feedstock for biodiesel production with enhanced cold flow characteristics

Energy Technology Data Exchange (ETDEWEB)

Yusup, Suzana; Khan, Modhar [Chemical Engineering Department, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, 31750 Tronoh, Perak (Malaysia)

2010-10-15

Research and development in the field of biodiesel showed that fatty acid methyl esters synthesized from agriculture or animal oils and fats, which exhibit qualifying properties, can replace diesel fuel used in internal combustion engine. However, the industry had some downfall recently with the fluctuating prices of edible oils and increasing demand for nutritional needs. Crude rubber seed oil (CRSO) and crude palm oil (CPO) were used in this study since both can be extracted and produced locally in Malaysia from their abundant plantations. The benefits of introducing such blend are that CRSO is considered a non-edible feedstock with no major industrial utilizations that has the potential to reduce the usage of CPO in biodiesel industry and was found to enhance the cold flow characteristics when blended with CPO by reducing the saturated fatty acids in the feedstock. The oils and blends were characterized for density, kinematic viscosity, heating value, acid value, free fatty acid content, refractive index, mono-, di- and triglycerides and sulphur content. Fatty acids composition and iodine value were established for an equivolume blend of the oils. (author)

Basic properties of crude rubber seed oil and crude palm oil blend as a potential feedstock for biodiesel production with enhanced cold flow characteristics

International Nuclear Information System (INIS)

Yusup, Suzana; Khan, Modhar

2010-01-01

Research and development in the field of biodiesel showed that fatty acid methyl esters synthesized from agriculture or animal oils and fats, which exhibit qualifying properties, can replace diesel fuel used in internal combustion engine. However, the industry had some downfall recently with the fluctuating prices of edible oils and increasing demand for nutritional needs. Crude rubber seed oil (CRSO) and crude palm oil (CPO) were used in this study since both can be extracted and produced locally in Malaysia from their abundant plantations. The benefits of introducing such blend are that CRSO is considered a non-edible feedstock with no major industrial utilizations that has the potential to reduce the usage of CPO in biodiesel industry and was found to enhance the cold flow characteristics when blended with CPO by reducing the saturated fatty acids in the feedstock. The oils and blends were characterized for density, kinematic viscosity, heating value, acid value, free fatty acid content, refractive index, mono-, di- and triglycerides and sulphur content. Fatty acids composition and iodine value were established for an equivolume blend of the oils.

Enbridge system : crude types, transportation and handling systems

Energy Technology Data Exchange (ETDEWEB)

Anand, A. [Enbridge Corp., Edmonton, AB (Canada)

2009-07-01

The supply of crude oil from the Western Canada Sedimentary Basin is expected to increase by approximately 2.1 million barrels per day by 2015. The crudes that Enbridge handles range from 19 API to 40 API and 0.1 per cent sulphur to 4.7 per cent sulphur. The diverse supply of crude oil that the Enbridge system handles includes conventional heavy, synthetic heavy, heavy high tan, heavy low residual, medium, light sour, heavy sour, light sweet, light sweet synthetic, condensate and olefinic crudes. This presentation discussed Enbridge's plans for infrastructure expansion, crude types and quality assurance program. The company's infrastructure plans include the expansion of regional pipelines to bring more supplies to the mainline; expansion of the mainline capacity to existing markets; and providing pipeline access to new markets. Merchant storage terminals will be provided in some locations. The quality of various crude types will be maintained through judicious sequencing and tank bottoms crossings. tabs., figs.

Canadian Petroleum Products Institute 1996 annual review

International Nuclear Information System (INIS)

1996-01-01

The Canadian Petroleum Products Institute (CPPI) is an association of Canadian companies involved in the downstream sector of the petroleum industry which includes refining, distributing and marketing of petroleum products. CPPI's mandate includes: (1) establishing environmental policies, (2) establishing working relationships with governments to develop public policy, (3) developing guidelines for the safe handling of petroleum products, and (4) providing information about the petroleum industry to the public. Canada's 19 refineries processed an average of 1.5 million barrels of crude oil per day in 1996. Domestic sources of crude made up 61 per cent of crude oil processed in 1996. Total exports during the year amounted to 105 million barrels. Some of the issues that the CPPI focused on during 1996 included the controversy over the future of the octane enhancing fuel additive MMT, fuel quality standards for transportation fuels and reformulated fuels, gasoline pricing, air quality and workplace safety. CPPI members' participation in the Voluntary Challenge and Registry (VCR) program towards reducing greenhouse gas emissions was also discussed. The industry was also actively involved in seeking to improve its refinery wastewater discharges

The importance of subsample preparation practices in the analysis of crude oils

Energy Technology Data Exchange (ETDEWEB)

Pereira, K.S.; Iorio, S.M.B.M. [Petroleo Brasileiro S.A. (CENPES/PETROBRAS), Rio de Janeiro, RJ (Brazil). Centro de Pesquisas], e-mail: katiapereira@petrobras.com.br; Marques, M.L.S.P. [Fundacao Gorceix, Ouro Preto, MG (Brazil)

2011-01-15

There have been many subsample preparation practices proposed to reduce sources of error in analyses of crude oils. Optimal subsample preparation allows keeping the degree of representativity of the final aliquot going into the laboratory analyzer. The objective of this work was to discuss some experiences in order to understand the importance of sampling practices to obtain representative subsamples of crude oils and petroleum products, and measurements with minimized uncertainty whenever possible. Specific practices, whose effectiveness was tested by experiments, are discussed in this work. The analysis of variance showed that the subsamples should not be used in vapor pressure tests unless in case of interlaboratory cross check, and have to be considered as the first test from the bottle subsample. Sometimes long periods of crude oils samples storage are necessary for a complete evaluation, but because of the effect of this storage time it was observed a trend in the reducing of acidity and sulfur content. (author)

Lipolysis og different oils using crude enzyme isolate from the intestinal tract of rainbow trout, Oncorhynchus mykiss

DEFF Research Database (Denmark)

Göttsche, J.R.; Nielsen, Nina Skall; Nielsen, Henrik Hauch

2005-01-01

Crude enzyme isolate was prepared from the intestine of rainbow trout. Positional specificity of the crude enzyme isolate was determined from both 1(3)- and 2-MAG products after i n vitro lipolysis of radioactive-labeled triolein. The ratio of 2- MAG/1(3)-MAG was 2:1, suggesting that the overall...... lipase specificity of the enzyme isolate from rainbow trout tended to be 1,3-specific; however, activity against the sn -2 position also was shown. In vitro lipolysis of four different unlabeled oils was performed with the crude enzyme isolate. The oils were: structured lipid [SL; containing the medium...

The dynamics of crude oil price differentials

International Nuclear Information System (INIS)

Fattouh, Bassam

2010-01-01

Crude oil price differentials are modelled as a two-regime threshold autoregressive (TAR) process using the method proposed by Caner and Hansen [Caner, M., Hansen, B.E. Threshold autoregression with a unit root. Econometrica 2001; 69; 1555-1596.]. While standard unit root tests suggest that the prices of crude oil of different varieties move closely together such that their price differential is stationary, the TAR results indicate strong evidence of threshold effects in the adjustment process to the long-run equilibrium. These findings suggest that crude oil prices are linked and thus at the very general level, the oil market is 'one great pool' (Adelman, M.A. International oil agreements. The Energy Journal 1984; 5; 1-9.). However, differences in the dynamics of adjustment suggest that within this one pool, oil markets are not necessarily integrated in every time period and hence the dynamics of crude oil price differentials may not follow a stationary process at all times. Although the development of a liquid futures market around the crude oil benchmarks has helped make some distant markets more unified, arbitrage is not costless or risk-free and temporary breakdowns in the benchmarks can lead to decoupling of crude oil prices. (author)

Design and analysis of fuel ethanol production from raw glycerol

International Nuclear Information System (INIS)

Posada, J.A.; Cardona, C.A.

2010-01-01

Three configurations for fuel ethanol production from raw glycerol using Escherichia coli were simulated and economically assessed using Aspen Plus and Aspen Icarus, respectively. These assessments considered raw glycerol (60 wt%) purification to both crude glycerol (88 wt%) and pure glycerol (98 wt%). The highest purification cost (PC) was obtained using pure glycerol due to its higher energy consumption in the distillation stage. In addition, the remaining methanol in the raw glycerol stream was recovered and recycled, decreasing the purification costs. The E. coli strain is able to convert crude glycerol (at 10 g/L or 20 g/L), or pure glycerol (at 10 g/L) to ethanol. Among these three glycerol concentrations, the lowest bioconversion cost was obtained when crude glycerol was diluted at 20 g/L. Purification and global production costs were compared with the commercial prices of glycerol and fuel ethanol from corn and sugarcane. Purification costs of raw glycerol were lower than previously reported values due to the methanol recovery. Global production costs for fuel ethanol from glycerol were lower than the reported values for corn-based production and higher than those for cane-based production. (author)

Performance of juvenile mojarra supplied with feed containing varying levels of crude protein

Directory of Open Access Journals (Sweden)

Ricardo Henrique Bastos de Souza

2016-04-01

Full Text Available ABSTRACT The growth of the Brazilian aquaculture has stimulated the development of the productive chain of native species, including marine environment. The objective of this study was to evaluate the growth performance of juvenile mojarra fish (Diapterus rhombeus fed diets containing different concentrations of crude protein (32, 36, 40 and 44 g 100 g-1. The 80 juvenile mojarra (7.2±1.5 g were kept in 16 circular tanks (150 L. The study design used was completely randomized with four treatments and four repetitions. The fish were fed four times a day. At the end of the experiment (60 days the final weight, feed intake, weight gain (WG, feed:gain ratio (FGR, protein efficiency rate (PER, energy efficiency rate, specific growth, survival rate and, body composition were evaluated. It was verified significant effect of protein level on the WG, with the best value at the level of 38.20 g 100 g-1 of crude protein. For FGR, the best estimated value occurred with 38.06 g 100 g-1 of crude protein, similar to that reported for the PER (38.91 g 100 g-1. The other performance parameters and body composition were not influenced by crude protein levels. Diet crude protein concentrations between 38.06 and 38.91 g 100 g-1 provide the best performance indices for juvenile mojarra.

Aviation fuel and future oil production scenarios

International Nuclear Information System (INIS)

Nygren, Emma; Aleklett, Kjell; Hoeoek, Mikael

2009-01-01

Most aviation fuels are jet fuels originating from crude oil. Crude oil must be refined to be useful and jet fuel is only one of many products that can be derived from crude oil. Jet fuel is extracted from the middle distillates fraction and competes, for example, with the production of diesel. Crude oil is a limited natural resource subject to depletion and several reports indicate that the world's crude oil production is close to the maximum level and that it will start to decrease after reaching this maximum. A post-Kyoto political agenda to reduce oil consumption will have the same effect on aviation fuel production as a natural decline in the crude oil production. On the other hand, it is predicted by the aviation industry that aviation traffic will keep on increasing. The industry has put ambitious goals on increases in fuel efficiency for the aviation fleet. Traffic is predicted to grow by 5% per year to 2026, fuel demand by about 3% per year. At the same time, aviation fuel production is predicted to decrease by several percent each year after the crude oil production peak is reached resulting in a substantial shortage of jet fuel by 2026. The aviation industry will have a hard time replacing this with fuel from other sources, even if air traffic remains at current levels.

Pengaruh Penambahan Kosubstrat pada Biodegradasi Crude Oil

Directory of Open Access Journals (Sweden)

Any Juliani

2016-06-01

Full Text Available Kegiatan penambangan minyak bumi tidak hanya dilakukan oleh perusahaan-perusahaan besar, tetapi juga oleh masyarakat secara tradisional. Potensi pencemaran lingkungan yang ditimbulkan oleh kegiatan penambangan rakyat ini menjadi lebih tinggi karena pengelolaannya yang tradisional. Salah satu jenis pencemaran yang ditimbulkannya misalnya adalah tanah atau perairan yang tercemar oleh minyak bumi (crude oil pada saat berlangsungnya kegiatan penambangan. Salah satu upaya untuk dapat mengatasinya adalah dengan bioremediasi. Bioremediasi merupakan teknologi pengolahan pencemar dengan memanfaatkan aktivitas mikroba, terutama dari golongan bakteri. Bioremediasi tersebut harus melibatkan bakteri yang memiliki kapasitas metabolic untuk melakukan biodegradasi terhadap crude oil tersebut. Crude oil sendiri pada dasarnya merupakan senyawa hidrokarbon yang merupakan sumber karbon yang kaya bagi mikroba. Namun demikian, biodegradasi crude oil relative lebih sulit dilakukan karena karakteristiknya yang merupakan senyawa dengan berat molekul dan ukuran yang besar. Oleh karena itu penambahan kosubstrat yang lebih sederhana dapat dilakukan untuk membantu biodegradasi terutama pada tahap awal proses. Penelitian ini dilakukan untuk mengetahui pengaruh penambahan kosubstrat dalam hal ini glukosa terhadap biodegradasi crude oil. Penelitian dilakukan dalam media cair dengan bioaugmentasi melalui penambahan inoculum bakteri yang diisolasi dari tanah yang dikondisikan terhadap crude oil dalam beberapa variasi reactor. Indikasi terjadinya biodegradasi diperiksa melalui pengukuran terhadap parameter Total Petroleum Hydrocarbon (TPH dan Total Plate Count (TPC. Hasil penelitian menunjukkan bahwa penambahan kosubstrat glukosa memberikan pengaruh positif terhadap penurunan TPH. Penurunan TPH tertinggi setelah 28 hari adalah sebesar 25,3 % yang diberikan oleh reactor dengan penambahan kosubstrat serta konsentrasi crude oil awal sebesar 8.1 %. Sementara itu reactor tanpa

Ruminal Methane Production on Simple Phenolic Acids Addition in in Vitro Gas Production Method

Directory of Open Access Journals (Sweden)

A. Jayanegara

2009-04-01

Full Text Available Methane production from ruminants contributes to total global methane production, which is an important contributor to global warming. In this experiment, six sources of simple phenolic acids (benzoic, cinnamic, phenylacetic, caffeic, p-coumaric and ferulic acids at two different levels (2 and 5 mM added to hay diet were evaluated for their potential to reduce enteric methane production using in vitro Hohenheim gas production method. The measured variables were gas production, methane, organic matter digestibility (OMD, and short chain fatty acids (SCFA. The results showed that addition of cinnamic, caffeic, p-coumaric and ferulic acids at 5 mM significantly (P p-coumaric > ferulic > cinnamic. The addition of simple phenols did not significantly decrease OMD. Addition of simple phenols tends to decrease total SCFA production. It was concluded that methane decrease by addition of phenolic acids was relatively small, and the effect of phenolic acids on methane decrease depended on the source and concentration applied.

Effect of Water Content, Temperature and NaCl on CO2 Corrosion of Carbon Steel (A106B in Iraqi Crude Oil

Directory of Open Access Journals (Sweden)

Saad Ahmed Jafar

2018-01-01

Full Text Available An investigation was carried out to determine the corrosion rate of carbon steel (A 106 GradeB as flow line in crude oil production with CO2 content employing three Iraqi crude oil (Kirkuk crude oil, Halfaya crude oil, and Rumalia crude oil with identical produced water (brine [1%NaCl,2%NaCl, and 3%NaCl]. Experiments were performed in an autoclave test apparatus, crude oilproduced water mixtures, water cuts were (0, 10, 20, 30, 40, and 100%, and temperature (20, 40, 60°C. For all experiments, CO2 partial pressure was maintained at 4bar and rotational speed 500 rpm. The corrosion rates were determined by the weight loss method. The results revealed that the corrosion rate of carbon steel increased by increasing water cut and temperature, but decreased with increasing salt concentration for all types of crude oil. Rumaila crude oil exhibited the highest corrosion rate and Kirkuk crude oil exhibits the lowest corrosion rate while Halfaya crude oil exhibits a moderate corrosion rate.

Reducing the cadmium content of crude phosphates and mineral fertilizers

Energy Technology Data Exchange (ETDEWEB)

Plessen, H von; Schimmel, G

1987-10-01

Crude sedimentary phosphates generally contain cadmium together with traces of other heavy metals. These Cd traces generally end up in fertilizers produced from the crude phosphates. Processes have therefore been developed to separate the Cd from the crude phosphate or from the crude phosphoric acids arising therefrom as intermediates. In this way, the Cd content of the crude phosphate can be reduced to less the 10% of its original value, and to 50% thereof by extractive treatment with acidic calcium nitrate solution. Older calcination processes for crude phosphate have been improved to give residual Cd contents of 10 to 50% at temperatures of 800 to 1000/sup 0/C. Cadmium can be removed almost quantitatively from crude phosphate by means of dialkyl dithiophosphoric acid esters by extraction, binding to adsorbents, or ion flotation. Cadmium can be extracted from crude acids in high yield by long-chained amines. After partial neutralization of the crude acids, precipitation as cadmium sulphide is also possible.

Influence of asphaltene aggregation and pressure on crude oil emulsion stability

Energy Technology Data Exchange (ETDEWEB)

Auflem, Inge Harald

2002-07-01

Water-in-crude oil emulsions stabilised by various surface-active components are one of the major problems in relation to petroleum production. This thesis presents results from high-pressure separation experiments on ''live'' crude oil and model oil emulsions, as well as studies of Interactions between various indigenous stabilising materials in crude oil. A high-pressure separation rig was used to study the influence of gas and gas bubbles on the separation of water-in-crude oil emulsions. The results were interpreted as a flotation effect from rising gas bubbles, which led to increased separation efficiency. The separation properties of a ''live'' crude oil were compared to crude oil samples recombined with various gases. The results showed that water-in-oil emulsions produced from the ''live'' crude oil samples, generally separated faster and more complete, than emulsions based on recombined samples of the same crude oil. Adsorption of asphaltenes and resins onto a hydrophilic surface from solutions with varying aromatic/aliphatic character was investigated by a quarts crystal microbalance. The results showed that asphaltenes adsorbed to a larger degree than the resins. The resins were unable to desorb pre-adsorbed asphaltenes from the surface, and neither did they adsorb onto the asphaltene-coated surface. In solutions of both of resins and asphaltenes the two constituents associated in bulk liquid and adsorbed to the surface in the form of mixed aggregates. Near infrared spectroscopy and pulsed field gradient spin echo nuclear magnetic resonance were used to study asphaltene aggregation and the influence of various amphiphiles on the asphaltene aggregate size. The results showed Interactions between the asphaltenes and various chemicals, which were proposed to be due to acid-base interactions. Among the chemicals used were various naphthenic acids. Synthesised monodisperse acids gave a reduction of size of the asphaltene aggregates, whereas polydisperse

Influence of asphaltene aggregation and pressure on crude oil emulsion stability

Energy Technology Data Exchange (ETDEWEB)

Auflem, Inge Harald

2002-07-01

Water-in-crude oil emulsions stabilised by various surface-active components are one of the major problems in relation to petroleum production. This thesis presents results from high-pressure separation experiments on ''live'' crude oil and model oil emulsions, as well as studies of Interactions between various indigenous stabilising materials in crude oil. A high-pressure separation rig was used to study the influence of gas and gas bubbles on the separation of water-in-crude oil emulsions. The results were interpreted as a flotation effect from rising gas bubbles, which led to increased separation efficiency. The separation properties of a ''live'' crude oil were compared to crude oil samples recombined with various gases. The results showed that water-in-oil emulsions produced from the ''live'' crude oil samples, generally separated faster and more complete, than emulsions based on recombined samples of the same crude oil. Adsorption of asphaltenes and resins onto a hydrophilic surface from solutions with varying aromatic/aliphatic character was investigated by a quarts crystal microbalance. The results showed that asphaltenes adsorbed to a larger degree than the resins. The resins were unable to desorb pre-adsorbed asphaltenes from the surface, and neither did they adsorb onto the asphaltene-coated surface. In solutions of both of resins and asphaltenes the two constituents associated in bulk liquid and adsorbed to the surface in the form of mixed aggregates. Near infrared spectroscopy and pulsed field gradient spin echo nuclear magnetic resonance were used to study asphaltene aggregation and the influence of various amphiphiles on the asphaltene aggregate size. The results showed Interactions between the asphaltenes and various chemicals, which were proposed to be due to acid-base interactions. Among the chemicals used were various naphthenic acids. Synthesised monodisperse acids gave a reduction of

Crude oil pricing report, issue 89, December 1992

International Nuclear Information System (INIS)

1992-01-01

This report is prepared by the Canadian Oil Markets and Emergency Planning Division (COMEP), Energy, Mines and Resources Canada. It provides a reference for domestic and imported crude oil prices in Canadian markets and illustrates the competitive position of Canadian crude in the U.S. market. The information in this report is in part based on the Crude Oil Pricing Survey (COPS), conducted by COMEP, of Canadian refiners' domestic crude oil purchases, refinery receipts, imports and data from trade publications as well as industry pricing bulletins. 8 tabs

Effect of incubation time of sago (metroxylon sago) waste by local microorganism ″ginta″ on ph, crude protein, and crude fiber content

Science.gov (United States)

Ginting, Nurzainah; Pase, E.

2018-03-01

This study aims to examine the effect of incubation times of sago waste by local microorganism (MOL) “Ginta” to the crude protein and crude fiber content in relation to finding a cheap and good quality ruminants feed alternative. Incubation times were 0 hours to 144 hours. The data obtained were analyzed using Completely Randomize Design consisting of seven treatments and three replications. The result showed that the duration of incubation of sago waste by local microorganism (MOL) “Ginta” caused pH reduction, improved crude protein and crude fiber content. pH reduction was from 7.03 at 0 hour to 4.05 at 144 hours incubation. The highest increased in crude protein was H6U3 (5.58%) : 144 hours incubation and the lowest was H0U2 (3.22%) : 0 hour incubation while the highest crude fiber was H0U1 (19.99%) : 0 hour incubation and the lowest was H6U3 (18.23%) : 144 hours incubation. It can be concluded that incubation of sago waste triggered lower pH, higher crude protein and lower crude fiber than uninoculated. A recommendation could be given on using MOL ‘Ginta” in order to produce a cheap and good quality ruminans feed alternative.

Study of the gelation behaviour of Brazilian waxy crude oils

Energy Technology Data Exchange (ETDEWEB)

Ziglio, C.M.; Sant' Ana, D.F. [Petroleo Brasileiro S.A., Petrobras, Rio de Janeiro (Brazil)

2008-07-01

The precipitation of wax from crude oil results in the formation of a paraffin network which evolves into a gel structure, causing a major operating issue for the petroleum industry. A gelled oil in a pipeline may need a very high re-start pressure that is beyond the capacity of the pump. The gelation of the oil can also develop into a wax deposit on the pipeline wall that restricts the flow of crude oil. Rheometry tests were used in this study to determine the yielding process of wax gels formed by the cooling of Brazilian crude oils. The effect of selected chemical additives on the gel strength was also examined. Dynamic rheology was used to study the oil-gel transition under quiescent conditions. Two rheological methods were used to study the gel yield stress, which is related to the gel strength. In the Creep and Recovery method, a stress was applied to the sample for a short period while the resulting deformation was measured. The stress was then removed to allow the sample to recover the gel structure. The steps of creep and recovery were repeated with an increasing stress value. The yield stress was identified as the minimum stress to cause an irreversible deformation in the sample. The yield stress of the gelled oil was estimated through dynamic measurements. Gel breakdown occurred when the sample was submitted to a critical strain, which is related to the yield stress value. This study showed that the gelation temperature can be reduced considerably by adding small amounts of readily available additives. These additives have an influence on yield stress values. In a cold re-start situation, they can reduce the pump pressure.

Microwave-gamma ray water in crude monitor

International Nuclear Information System (INIS)

Paap, H.J.

1984-01-01

A microwave-gamma ray water-in-crude monitoring system measures the percent quantity of fresh water or salt water in crude oil flowing in a pipe line. The system includes a measuring cell arranged with the pipe line so that the crude oil flows through the measuring cell. A microwave transmitter subsystem and a gamma ray source are arranged with the measuring cell so that microwave energy and gamma rays are transmitted through the measuring cell. A microwave receiving subsystem and a gamma ray detector provide signals corresponding to received microwave energy and to the received gamma rays, respectively. Apparatus connected to the microwave receiver and to the gamma ray detector provides an indication of the percentage of water in the crude oil

PRELIMINARY STUDIES FOR PRODUCING CRUDE LIPASE FROM TEMPE’S MOULD CULTIVATED IN RICE-HUSK-BASED SOLID MEDIA

Directory of Open Access Journals (Sweden)

Teuku Beuna Bardant

2010-06-01

Full Text Available The goal of these preliminary studies is to support Indonesian program for increasing palm oil added value through independent production technology based on Indonesian natural resources. Various palm oil derivatives could be synthesized enzymatically using lipase from microbes that available in Indonesia. Tempe's mould is available in abundance in Indonesia and had already been proved for producing lipase. This paper provides information about producing crude lipase from Tempe's mould cultivated in rice-husk-based solid media using palm oil as carbon source. Observed variables include solid media composition, optimum fermentation time, extraction and enriching process of crude lipase. The crude lipase was analyzed its hydrolysis activity on coconut oil and palm oil. The result of these preliminary studies shows that this production process is a simple and tough process and very potential to be developed.   Keywords: lipase, Tempe's mould, palm oil, solid fermentation, rice husk

Recovery Act Production of Algal BioCrude Oil from Cement Plant Carbon Dioxide

Energy Technology Data Exchange (ETDEWEB)

Robert Weber; Norman Whitton

2010-09-30

The consortium, led by Sunrise Ridge Algae Inc, completed financial, legal, siting, engineering and environmental permitting preparations for a proposed demonstration project that would capture stack gas from an operating cement plant and convert the carbon dioxide to beneficial use as a liquid crude petroleum substitute and a coal substitute, using algae grown in a closed system, then harvested and converted using catalyzed pyrolysis.

10 CFR 212.78 - Tertiary incentive crude oil.

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Tertiary incentive crude oil. 212.78 Section 212.78 Energy DEPARTMENT OF ENERGY OIL MANDATORY PETROLEUM PRICE REGULATIONS Producers of Crude Oil § 212.78 Tertiary incentive crude oil. Annual prepaid expenses report. By January 31 of each year after 1980, the project...

Cu determination in crude oil distillation products by atomic absorption and inductively coupled plasma mass spectrometry after analyte transfer to aqueous solution

International Nuclear Information System (INIS)

Kowalewska, Zofia; Ruszczynska, Anna; Bulska, Ewa

2005-01-01

Cu was determined in a wide range of petroleum products from crude oil distillation using flame atomic absorption spectrometry (FAAS), electrothermal atomic absorption spectrometry (ETAAS) and inductively coupled plasma mass spectrometry (ICP-MS). Different procedures of sample preparation were evaluated: (i) mineralization with sulfuric acid in an open system (ii) mineralization in a closed microwave system (iii) combustion in hydrogen-oxygen flame in the Wickbold's apparatus (iv) matrix evaporation followed by acid dissolution, and (v) acidic extraction. All the above procedures led to the transfer of the analyte into an aqueous solution for the analytical measurement step. It was found that application of FAAS was limited to the analysis of the heaviest petroleum products of high Cu content. In ICP-MS, the use of internal reference method (with Rh or In as internal reference element) was required to eliminate the matrix effects in the analysis of extracts and the concentrated solutions of mineralized heavy petroleum products. The detection limits (in original samples) were equal to, respectively, 10, 86, 3.3, 0.9 and 0.4 ng g -1 in procedures i-v with ETAAS detection and 10, 78, 1.1 and 0.5 ng g -1 in procedures i-iii and v with ICP-MS detection. The procedures recommended here were validated by recovery experiments, certified reference materials analysis and comparison of results, obtained for a given sample, in different ways. The Cu content in the analyzed samples was: 50-110 ng g -1 in crude oil, -1 in gasoline, -1 in atmospheric oil, -1 in heavy vacuum oil and 140-300 ng g -1 in distillation residue

Production of gaseous and liquid chemicals by aqueous phase reforming of crude glycerol: Influence of operating conditions on the process

International Nuclear Information System (INIS)

Remón, J.; Giménez, J.R.; Valiente, A.; García, L.; Arauzo, J.

2016-01-01

Highlights: • Aqueous phase reforming: a tailor-made process for the valorisation of crude glycerol. • In-depth understanding of the effect of the operating conditions on the process. • Process optimisation for the selective production of valuable gas and liquid products. • Low pressure and high temperature and spatial time favour gas production. • High pressure and medium temperature maximise the production of valuable liquids. - Abstract: The present work studies the influence of the temperature (200–240 °C), pressure (38–50 bar), glycerol concentration (10–50 wt.%) and mass of catalyst/ glycerol mass flow rate ratio (W/m_g_l_y_c_e_r_o_l = 10–40 g catalyst min/g glycerol) during the aqueous phase reforming (APR) of a glycerol solution obtained from the production of biodiesel. The operating conditions exerted a statistically significant influence on the reforming results. Specifically, the global glycerol conversion and the carbon converted into gas and liquid products varied as follows: 4–100%, 1–80% and 16–93%, respectively. The gas phase was made up of H_2 (8–55 vol.%), CO_2 (34–66 vol.%), CO (0–4 vol.%) and CH_4 (6–45 vol.%). The liquid phase consisted of a mixture of alcohols (monohydric: methanol and ethanol; and polyhydric: 1,2-propanediol, 1,2-ethanediol, 2,3-butanediol), aldehydes (acetaldehyde), ketones (C3-ketones: acetone and 2-propanone-1-hydroxy; C4-ketones: 2-butanone-3-hydroxy and 2-butanone-1-hydroxy; and cyclic ketones), carboxylic acids (acetic and propionic acids) and esters (1,2,3-propanetriol-monoacetate), together with unreacted glycerol and water. The relative amount (free of water and un-reacted glycerol) of these compounds in the liquid phase was as follows: monohydric alcohols: 4–47%, polyhydric-alcohols: 14–68%, aldehydes: 0–5%, C3-ketones: 2–33%, C4-ketones: 0–10%, ciclo-ketones: 0–6%, carboxylic acids: 2–43%, and esters: 0–46%. This process turned out to be highly customisable for the

Inhibition of TNF-α production in LPS-activated THP-1 monocytic cells by the crude extracts of seven Bhutanese medicinal plants.

Science.gov (United States)

Wangchuk, Phurpa; Keller, Paul A; Pyne, Stephen G; Taweechotipatr, Malai

2013-07-30

Seven studied medicinal plants; Aconitum laciniatum, Ajania nubigena, Codonopsis bhutanica, Corydalis crispa, Corydalis dubia, Meconopsis simplicifolia and Pleurospermum amabile, are currently used in the Bhutanese Traditional Medicine (BTM) for the management of different types of disorders including the diseases that bore relevance to various inflammatory conditions. This study aimed to evaluate the inhibition of TNF-α production in LPS-activated THP-1 monocytic cells by the crude extracts of seven selected Bhutanese medicinal plants. It is expected to; (a) generate a scientific basis for their use in the BTM and (b) form a basis for prioritization of the seven plants for further phytochemical and anti-inflammatory studies. Seven plants were selected using an ethno-directed bio-rational approach and their crude extracts were prepared using four different solvents (methanol, hexane, dichloromethane and chloroform). The TNF-α inhibitory activity of these extracts was determined by cytokine-specific sandwich quantitative enzyme-linked immunosorbent assays (ELISAs). The results were quantified statistically and the statistical significance were evaluated by GraphPad Prism version 5.01 using Student's t-test with one-tailed distribution. A p-value ≤0.05 was considered statistically significant. Of the seven plants studied, the crude extracts of six of them inhibited the production of pro-inflammatory cytokine, TNF-α in LPS-activated THP-1 monocytic cells. Amongst the six plants, Corydalis crispa gave the best inhibitory activity followed by Pleurospermum amabile, Ajania nubigena, Corydalis dubia, Meconopsis simplicifolia and Codonopsis bhutanica. Of the 13 extracts that exhibited statistically significant TNF-α inhibitory activity (p<0.05; p<0.01), five of them showed very strong inhibition when compared to the DMSO control and RPMI media. Six medicinal plants studied here showed promising TNF-α inhibitory activity. These findings rationalize the traditional

Improving Aspergillus carbonarius crude enzymes for lignocellulose hydrolysis

DEFF Research Database (Denmark)

Hansen, Gustav Hammerich

and single enzyme supplementation. Fungal strains were screened in order to determine crude enzyme extracts that could be supplemented as boosters of A. carbonarius own crude enzyme extract, when applied in lignocellulose hydrolysis. The fungi originated from different environmental niches, which all had...... for their potential in hydrolysis of wheat straw both by application of monocultures and by supplementing to crude enzymes of A. carbonarius. For the crude enzymes from solid cultivations there were eight isolates that showed synergistic interaction resulting in doubling and tripling of the glucose release in wheat...... straw hydrolysis. A completely different profile of synergy was observed for crude enzymes from liquid cultivations, as there were only three isolates that enhanced glucose release. Only one of these three isolates had shown synergistic effects when cultivated in a solid medium. The screening...

Prediction of compatibility of crude oils with condensate (C5+); Previsao de compatibilidade de petroleos e condensado (C5+)

Energy Technology Data Exchange (ETDEWEB)

Zilio, Evaldo Lopez; Santos, Maria de Fatima Pereira dos [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Ramos, Antonio Carlos da Silva; Rolemberg, Marlus Pinheiro [Universidade Federal do Maranhao (UFMA), Sao Luis, MA (Brazil)

2008-07-01

Due to the recent raise of the national natural gas demand and to the need of flowing the condensates (C5+) produced from the NGPP (Natural Gas Processing Plant) by adding them to the streams of the crude oil, there was the need to carry out the compatibility prediction of one condensate with two onshore crude oils from Espirito Santo. The model to predict the compatibility among crude oils and among crude oils and oil products is based on the use of the solubility parameter of the oils. To apply it, the solubility parameter of each crude oil or oil product is measured and the parameter of their blend is calculated. If this value is beneath the asphaltenes flocculation parameter, the blend is incompatible; if it is above, the blend is compatible. In this article, the compatibility predictions were done according to the Solubility Parameter Model to two blends: the condensate C with the crude oil X and with the crude oil Y. The model predictions are that both blends are incompatible at given proportions. To check the predictions, the same two blends were experimentally carried out. It must be emphasized that the compatibility tests were done at atmospheric pressure and at the temperature of 15 deg C. These tests consist in adding the condensate to the crude oil with a titrater and visualizing the asphaltenes precipitation at an optical microscope. The experimental results were equivalent to the values predicted by the model. It is worth mentioning that there were several practical difficulties, as the high volatility of the condensate and the fact that the temperatures to determine the parameters and to carry out the tests were very lower than the operation temperature. Therefore, a security factor was applied on the predictions (less 20%). (author)

Tapping into new markets for heavy crude : sustaining oil sands development in the long term

International Nuclear Information System (INIS)

Schrage, W.

2003-01-01

In 2002, 65 per cent of supply from the Western Canadian Sedimentary Basin (WCSB) was shipped by Enbridge to North American markets. A survey of refineries is used by Enbridge to establish expected market demand for oil from the WCSB. An Oil Sands Markets Study was undertaken to provide answers to the following: (1) what volumes to which markets will maximize the value of WCSB production? (2) what mix of raw bitumen, synthetic and fully saturated synthetic best fits the available markets? and (3) what infrastructure expansions, extensions, conversions and new development will be required? Enbridge elected to use the North American petroleum model using Alto's MarketPoint system. It was adapted to evaluate crude oil and refined products. It is expected that by the end of the first quarter of 2003, the preliminary results will be available for review with industry. There are currently 20 crude types identified as available to refineries. All imported crude types will be included. Eight distinct classes of refined products were used: liquid propane gas (LPG), low and high sulphur gasoline, jet fuel, low and high sulphur distillate, asphalt and coke. All major conversion units were modeled for all 150 refineries in Canada and the United States. figs

Application of alkaline waterflooding to a high acidity crude oil

Energy Technology Data Exchange (ETDEWEB)

Sayyouh, M.H. (King Sand Univ., Riyadh (SA). Petroleum Engineering Dept.); Abdel-Waly, A.; Osman, A. (Cairo Univ. (EG). Petroleum Engineering Dept.); Awara, A.Z. (Geisum Oil Company, Cairo (EG))

The enhanced recovery of a high acidity crude oil (South Geisum crude) by alkaline solutions is studied. Acidity, interfacial tension, and contact angle, were investigated. Displacement tests were carried out to study the effect of alkaline slug concentration, slug size, oil alkali type, temperature and viscosity on recovery. The interfacial tension between crude oil and formation water decreases with increasing alkaline concentration until a minimum, after which it increases again. Contact angle measurements indicated oil-wetting conditions that increase by the addition of alkaline solutions. At the early stages of displacement, oil recovery increases with increasing alkaline concentration until a maximum at 4% by weight NaOH concentration. Also, at such early stages, an excessive increase in alkaline concentration results in lower oil recovery. On the other hand, after the injection of many pore volumes of water, oil recovery is almost the same regardless of the alkaline concentration. Oil recovery increases with increasing alkaline slug size until a maximum at 15% PV. Sodium hydroxide slugs produce more oil recovery than sodium carbonate slugs. Oil recovery increases with increasing temperature (from 25 to 55{sup 0}C) and decreasing oil viscosity.

Forecasting Crude Oil Price Using EEMD and RVM with Adaptive PSO-Based Kernels

Directory of Open Access Journals (Sweden)

Taiyong Li

2016-12-01

Full Text Available Crude oil, as one of the most important energy sources in the world, plays a crucial role in global economic events. An accurate prediction for crude oil price is an interesting and challenging task for enterprises, governments, investors, and researchers. To cope with this issue, in this paper, we proposed a method integrating ensemble empirical mode decomposition (EEMD, adaptive particle swarm optimization (APSO, and relevance vector machine (RVM—namely, EEMD-APSO-RVM—to predict crude oil price based on the “decomposition and ensemble” framework. Specifically, the raw time series of crude oil price were firstly decomposed into several intrinsic mode functions (IMFs and one residue by EEMD. Then, RVM with combined kernels was applied to predict target value for the residue and each IMF individually. To improve the prediction performance of each component, an extended particle swarm optimization (PSO was utilized to simultaneously optimize the weights and parameters of single kernels for the combined kernel of RVM. Finally, simple addition was used to aggregate all the predicted results of components into an ensemble result as the final result. Extensive experiments were conducted on the crude oil spot price of the West Texas Intermediate (WTI to illustrate and evaluate the proposed method. The experimental results are superior to those by several state-of-the-art benchmark methods in terms of root mean squared error (RMSE, mean absolute percent error (MAPE, and directional statistic (Dstat, showing that the proposed EEMD-APSO-RVM is promising for forecasting crude oil price.

Crude oil import policy of Turkey: Historical analysis of determinants and implications since 1968

International Nuclear Information System (INIS)

Ediger, Volkan S.; Berk, Istemi

2011-01-01

Turkey is one of the most energy import dependent countries in the world, suffering deeply from the economic and strategic burdens of oil importation. Our purpose is to determine the factors behind the crude oil import policy of Turkey and to measure their contribution to a well-organized import strategy. We implemented a principle component analysis to construct an Oil Import Vulnerability Index (OIVI) based on four factors, which are crude oil import dependency of primary energy consumption, crude oil import bill as a share of Gross Domestic Product (GDP), non-diversification of import sources, and share of oil in total energy import. The contribution of these factors to the OIVI is found to be approximately equal. While an overall deterioration in the OIVI has been observed during periods of increasing oil prices, better diversification of oil import sources has lead to significant improvements. We suggest Turkish policy-makers implement sound policies, emphasizing diversification of crude oil import sources and reduction of the share of crude oil in primary energy imports to increase energy supply security. This study has also demonstrated that it is possible to construct an index representing crude oil vulnerability caused by import dependency. - Research highlights: →We examine the factors lying behind the crude oil import policy of Turkey. → We measure the contribution of each factor to a well-organized import strategy. → We constrtuct an Oil Import Vulnerability Index using principle component analysis. → We suggest that four factors affect oil import policies with almost equal weights. → Source diversification is found to be the core issue in oil import policies.

Crude oil import policy of Turkey: Historical analysis of determinants and implications since 1968

Energy Technology Data Exchange (ETDEWEB)

Ediger, Volkan S., E-mail: volkanediger@gmail.co [Izmir University of Economics, Sakarya Caddesi, No. 156, 35330 Izmir (Turkey); Berk, Istemi [Izmir University of Economics, Sakarya Caddesi, No. 156, 35330 Izmir (Turkey)

2011-04-15

Turkey is one of the most energy import dependent countries in the world, suffering deeply from the economic and strategic burdens of oil importation. Our purpose is to determine the factors behind the crude oil import policy of Turkey and to measure their contribution to a well-organized import strategy. We implemented a principle component analysis to construct an Oil Import Vulnerability Index (OIVI) based on four factors, which are crude oil import dependency of primary energy consumption, crude oil import bill as a share of Gross Domestic Product (GDP), non-diversification of import sources, and share of oil in total energy import. The contribution of these factors to the OIVI is found to be approximately equal. While an overall deterioration in the OIVI has been observed during periods of increasing oil prices, better diversification of oil import sources has lead to significant improvements. We suggest Turkish policy-makers implement sound policies, emphasizing diversification of crude oil import sources and reduction of the share of crude oil in primary energy imports to increase energy supply security. This study has also demonstrated that it is possible to construct an index representing crude oil vulnerability caused by import dependency. - Research highlights: {yields}We examine the factors lying behind the crude oil import policy of Turkey. {yields} We measure the contribution of each factor to a well-organized import strategy. {yields} We constrtuct an Oil Import Vulnerability Index using principle component analysis. {yields} We suggest that four factors affect oil import policies with almost equal weights. {yields} Source diversification is found to be the core issue in oil import policies.

Corrosion testing on crude oil tankers and other product carriers by means of acoustic emission (AE)

Energy Technology Data Exchange (ETDEWEB)

Lackner, Gerald [TUV Austria, Deutschstrasse 10, 1230 Wien (Austria); Tscheliesnig, Peter [TUV Austria, Deutschstrasse 10, 1230 Wien (Austria)

2004-07-01

In the last decades a lot of maritime disasters with crude oil tankers occurred (e.g. Exxon- Valdez, Erika, Prestige). Every accident led to extreme pollution with horrible consequences not only for the environment but also for the life of the inhabitants of the affected coasts. Although most of these accidents were caused by human errors, the material degradation of the ship hull due to corrosion played an important role. Acoustic emission (AE) is already used to detect and discriminate the stage of corrosion of structures located on land. A consortium consisting of experienced partners from the fields of ship building and classification as well as from AE testing and equipment manufacturing started to investigate the feasibility of this testing technique for its application on oil tankers. The aim of the research project funded by the European Commission is to develop an on-line corrosion monitoring technique based on a permanent installation of AE sensors as well as a spot testing technique during stops in harbors or at anchorages using mobile equipment. Since the project was started, a lot of lab tests as well as background measurements were done on different types of tankers up to a size of 35.000 dead weight tons (DWT). The gathered data were evaluated with a frequency domain based pattern recognition system and it was possible to distinguish the AE signals related to corrosion from those signals, which were emitted by the structure due to the harsh environment on sea (background noise). Together with the oncoming developments of the AE equipment and the improvement of the data base, this project will lead to an important breakthrough for the safe shipping of hazardous products like crude oil. (authors)

Biosurfactant and Degradative Enzymes Mediated Crude Oil Degradation by Bacterium Bacillus subtilis A1

Science.gov (United States)

Parthipan, Punniyakotti; Preetham, Elumalai; Machuca, Laura L.; Rahman, Pattanathu K. S. M.; Murugan, Kadarkarai; Rajasekar, Aruliah

2017-01-01

In this work, the biodegradation of the crude oil by the potential biosurfactant producing Bacillus subtilis A1 was investigated. The isolate had the ability to synthesize degradative enzymes such as alkane hydroxylase and alcohol dehydrogenase at the time of biodegradation of hydrocarbon. The biosurfactant producing conditions were optimized as pH 7.0, temperature 40°C, 2% sucrose and 3% of yeast extract as best carbon and nitrogen sources for maximum production of biosurfactant (4.85 g l-1). Specifically, the low molecular weight compounds, i.e., C10–C14 were completely degraded, while C15–C19 were degraded up to 97% from the total hydrocarbon pools. Overall crude oil degradation efficiency of the strain A1 was about 87% within a short period of time (7 days). The accumulated biosurfactant from the biodegradation medium was characterized to be lipopeptide in nature. The strain A1 was found to be more robust than other reported biosurfactant producing bacteria in degradation efficiency of crude oil due to their enzyme production capability and therefore can be used to remove the hydrocarbon pollutants from contaminated environment. PMID:28232826

Ultrasound Assisted Synthesis of Hydroxylated Soybean Lecithin from Crude Soybean Lecithin as an Emulsifier.

Science.gov (United States)

Chiplunkar, Pranali P; Pratap, Amit P

2017-10-01

Soybean lecithin is a by-product obtained during degumming step of crude soybean oil refining. Crude soybean lecithin (CSL) contains major amount of phospholipids (PLs) along with minor amount of acylglycerols, bioactive components, etc. Due to presence of PLs, CSL can be used as an emulsifier. Crude soybean lecithin (CSL) was utilized to synthesize hydroxylated soybean lecithin (HSL) by hydroxylation using hydrogen peroxide and catalytic amount of lactic acid to enhance the hydrophilicity and emulsifying properties of CSL. To reduce the reaction time and to increase rate of reaction, HSL was synthesized under ultrasound irradiation. The effect of different operating parameters such as lactic acid, hydrogen peroxide, temperature, ultrasonic power and duty cycle in synthesis of HSL were studied and optimized. The surface tension (SFT), interfacial tension (IFT) and the critical micelle concentration (CMC) of the HSL (26.11 mN/m, 2.67 mN/m, 112 mg/L) were compared to CSL (37.53 mN/m, 6.22 mN/m, 291 mg/L) respectively. The HSL has better emulsion stability and low foaming characteristics as compared to CSL. Therefore, the product as an effective emulsifier can be used in food, pharmacy, lubricant, cosmetics, etc.

Factor substitution, and economies of scale and utilisation in Kuwait's crude oil industry

International Nuclear Information System (INIS)

Al-Mutairi, Naief; Burney, Nadeem A.

2002-01-01

The cost structure of the crude oil industry in Kuwait has been examined, with specific focus on factor substitution, and economies of scale and utilisation. This has been done by estimating translog cost functions, both long-run and short-run, using time-series data covering the period from 1976 to 1996. The results indicate that the implied production structure is non-homothetic, and the pattern of scale effect is labour saving, but capital and material using. The evidence also supports the presence of an induced exogenous technical change, which is non-neutral (labour and capital using, and material saving). The elasticity of substitution between capital and labour is positive, implying that the two inputs are substitute. The results also indicate the existence of diseconomies of scale in the production of crude oil, but no economies or diseconomies of utilisation

Production expansion continues to accelerate

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that Saudi Arabian Oil Co. (Saudi Aramco) is continuing its accelerated Crude Oil Expansion Program initiated in 1989 that aims at achieving a 10 million bpd productive capacity by 1995. In addition to major engineering, construction and renovation work related to production expansion, Saudi Aramco drilling and workover operations have been markedly expanded. Since January 1991, rig activity has doubled. As an indication of aging of Saudi production, projects include modernizing current injection water treatment facilities, installing a new seawater injection plant on the Persian Gulf, installing dewatering facilities in a number of locations and installing a pilot gas lift project. In addition, equipment orders indicate the new discoveries south of Riyadh may also need the assistance of water injection from inception of production

Molluscicidal activity of crude water leaf extracts of Alternanthera ...

African Journals Online (AJOL)

mortality figures by the use of probit gave LC50 of 40.42 (35.15 – 46.47) for the unevaporated crude water while the evaporated crude water extract had LC50 of 48.07 (42.81 – 54.28) for the dried leaf extract. For the fresh leaves the unevaporated crude water extract had LC50 of 32.57 (27.15 – 39.08) and evaporated crude ...

Bacterial consortia for crude oil spill remediation

International Nuclear Information System (INIS)

Chhatre, S.; Purohit, H.; Shanker, R.; Khanna, P.

1996-01-01

Oil spills generate enormous public concern and highlight the need for cost effective ad environmentally acceptable mitigation technologies. Physico-chemical methods are not completely effective after a spill. Hence, there is a need for improved and alternative technologies. Bioremediation is the most environmentally sound technology for clean up. This report intends to determine the potential of a bacterial consortium for degradation of Gulf and Bombay High crude oil. A four membered consortium was designed that could degrade 70% of the crude oil. A member of consortium produced a biosurfactant, rhamnolipid, that emulsified crude oil efficiently for effective degradation by the other members of consortium. The wide range of hydrocarbonoclastic capabilities of the selected members of bacterial consortium leads to the degradation of both aromatic and aliphatic fractions of crude oil in 72 hours. (Author)

Developmental toxicity in flounder embryos exposed to crude oils derived from different geographical regions.

Science.gov (United States)

Jung, Jee-Hyun; Lee, Eun-Hee; Choi, Kwang-Min; Yim, Un Hyuk; Ha, Sung Yong; An, Joon Geon; Kim, Moonkoo

2017-06-01

Crude oils from distinct geographical regions have distinct chemical compositions, and, as a result, their toxicity may be different. However, developmental toxicity of crude oils derived from different geographical regions has not been extensively characterized. In this study, flounder embryos were separately exposed to effluents contaminated by three crude oils including: Basrah Light (BLO), Pyrenees (PCO), and Sakhalin Vityaz (SVO), in addition to a processed fuel oil (MFO-380), to measure developmental toxicity and for gene expressions. Each oil possessed a distinct chemical composition. Edema defect was highest in embryos exposed to PCO and MFO-380 that both have a greater fraction of three-ring PAHs (33% and 22%, respectively) compared to BLO and SVO. Observed caudal fin defects were higher in embryos exposed to SVO and MFO-380, which are both dominated by naphthalenes (81% and 52%, respectively). CYP1A gene expressions were also highest in embryos exposed to SVO and MFO-380. Higher incidence of cardiotoxicity and lower nkx 2.5 expression were detected in embryos exposed to PCO. Unique gene expression profiles were observed in embryos exposed to crude oils with distinct compositions. This study demonstrates that crude oils of different geographical origins with different compositional characteristics induce developmental toxicity to different degrees. Copyright © 2017 Elsevier Inc. All rights reserved.

Biodegradation of chlorobenzene using immobilized crude extracts ...

African Journals Online (AJOL)

SERVER

2007-10-04

Oct 4, 2007 ... immobilized crude extracts were reused for all other experiments and found that immobilization .... India which are of analytical reagent grade. .... 9. 60. 3. 1. Figure 3. Degradation of chlorobenzene by immobilized crude.

A Study on the Determination of the World Crude Oil Price and Methods for Its Forecast

Energy Technology Data Exchange (ETDEWEB)

Kim, J.K. [Korea Energy Economics Institute, Euiwang (Korea)

2001-11-01

religions with only God are continuously fighting among themselves to implant their religious principles over the world. This report attempted to investigate environmental factors affecting the determination of the world crude oil price. First of all, this report reviewed the trend of the determination of the world crude oil and its formula that informed importing countries. Secondly, environmental factors to decide the world crude oil are investigated by oil producing countries, oil consuming countries, and the US. In investigating environmental factors, the crude oil producing countries have a positive relationship between increasing demand of oil and the trend of crude oil prices with analysis of covariance({delta}) and correlation({sigma}) in 1971 to 1999. But there is no constant relationship between decreasing oil production and increasing oil prices with correlation. The trend of oil stocks in OECD and the trend of oil prices demonstrated the same direction in analysis of {delta} and {sigma} so that their relationships are significant. In addition, the relationship between SPR of the US and the trend of crude oil prices showed a negative relationship so that the relation has no meaning. It seems a political power game. In order to create the forecasting model of the world crude oil price, this report firstly reviewed the existing forecasting models such as Pindyck and a simulation. The reviewing results showed that Pindyck model with optimization did not consider the concept of 'back stop technology' and the simulation model did not include the concept of non-market such as political factors and oil producing countries' disciplined adherence. Finally, therefore, this report tried to include market mechanism and non-market factors mentioned above to forecast the world crude oil price using KEEIOF model. But this report did not show precise empirical results from KEEIOF model due to the lack of appropriate data and time constraint. KEEIOF model accounts

Production and some properties of crude alkaline proteases of indigenous Central Amazonian rhizobia strains

Directory of Open Access Journals (Sweden)

Arlem Nascimento de Oliveira

2010-10-01

Full Text Available Two rhizobia strains isolated from soils of the Central Amazonian floodplain produced appreciable quantities of crude alkaline protease extracts with inexpensive carbon and nitrogen sources. These protease crude extracts were optimally active at pH 9.0-11.0. The optimum temperatures were 35 ºC for Rhizobium sp. strain R-986 and 55 ºC for Bradyrhizobium sp. strain R-993. Protease activities in the crude extracts were enhanced in the presence of 5 mM metal ions, such as Na+, Ca2+, Mg2+ and Mn2+. Rhizobia proteases were strongly inhibited by PMSF, a serine-protease inhibitor. The enzymes were active in the presence of surfactants (SDS and Triton X-100 and stable in oxidizing (H2O2 and reducing agents (β-mercaptoethanol, and organic solvents (acetone, hexane, methanol, 1-propanol and toluene.Duas estirpes de rizóbia isoladas de solos de várzea da Amazônia Central produziram grandes quantidades de proteases alcalinas extracelulares, usando fontes baratas de carbono e nitrogênio. Os extratos brutos de proteases foram ativos em pH 9,0-11,0. As temperaturas ótimas foram de 35 ºC para a enzima do Rhizobium R-986 e de 55 ºC para a do Bradyrhizobium R-993. As atividades proteolíticas aumentaram na presença de 5 mM dos íons Na+, Ca2+ , Mg2+ e Mn2+ . As proteases secretadas pelos rizóbios foram fortemente inibidas por PMSF, um inibidor de serina protease. As enzimas foram ativas na presença de surfactantes (SDS e Triton X-100, e estáveis na presença de agentes oxidantes (H2O2 e redutores (β-mercaptoetanol e solventes orgânicos (acetona, hexano, metanol, 1-propanol e tolueno.

Application of bacterial cytological profiling to crude natural product extracts reveals the antibacterial arsenal of Bacillus subtilis.

Science.gov (United States)

Nonejuie, Poochit; Trial, Rachelle M; Newton, Gerald L; Lamsa, Anne; Ranmali Perera, Varahenage; Aguilar, Julieta; Liu, Wei-Ting; Dorrestein, Pieter C; Pogliano, Joe; Pogliano, Kit

2016-05-01

Although most clinically used antibiotics are derived from natural products, identifying new antibacterial molecules from natural product extracts is difficult due to the complexity of these extracts and the limited tools to correlate biological activity with specific molecules. Here, we show that bacterial cytological profiling (BCP) provides a rapid method for mechanism of action determination on plates and in complex natural product extracts and for activity-guided purification. We prepared an extract from Bacillus subtilis 3610 that killed the Escherichia coli lptD mutant and used BCP to observe two types of bioactivities in the unfractionated extract: inhibition of translation and permeablization of the cytoplasmic membrane. We used BCP to guide purification of the molecules responsible for each activity, identifying the translation inhibitors bacillaene and bacillaene B (glycosylated bacillaene) and demonstrating that two molecules contribute to cell permeabilitization, the bacteriocin subtilosin and the cyclic peptide sporulation killing factor. Our results suggest that bacillaene mediates translational arrest, and show that bacillaene B has a minimum inhibitory concentration 10 × higher than unmodified bacillaene. Finally, we show that BCP can be used to screen strains on an agar plate without the need for extract preparation, greatly saving time and improving throughput. Thus, BCP simplifies the isolation of novel natural products, by identifying strains, crude extracts and fractions with interesting bioactivities even when multiple activities are present, allowing investigators to focus labor-intensive steps on those with desired activities.

DOE turns down all bids for Elk Hills crude

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that the U.S. Department of Energy has rejected all bids submitted in the Mar. 5 semiannual sale of crude oil from Elk Hills Naval Petroleum Reserve (NPR-1) in California. DOE the all 19 bids for the 53,740 b/d of crude were too low. The bids ranged from $11.71 to $14.06/bbl, with the top bids for the highest quality Stevens zone crude averaging $13.25/bbl. California oil companies the they bid what the market would bear, explaining a surplus of Alaskan crude on the West Coast has driven down the price of local crudes, notably heavy crudes. DOE will extend the current oil purchase contracts through April while it issues a new request for bids. It planned to issue the solicitation Mar. 23 and receive bids Apr. 15

Forecasting volatility of crude oil markets

International Nuclear Information System (INIS)

Kang, Sang Hoon; Kang, Sang-Mok; Yoon, Seong-Min

2009-01-01

This article investigates the efficacy of a volatility model for three crude oil markets - Brent, Dubai, and West Texas Intermediate (WTI) - with regard to its ability to forecast and identify volatility stylized facts, in particular volatility persistence or long memory. In this context, we assess persistence in the volatility of the three crude oil prices using conditional volatility models. The CGARCH and FIGARCH models are better equipped to capture persistence than are the GARCH and IGARCH models. The CGARCH and FIGARCH models also provide superior performance in out-of-sample volatility forecasts. We conclude that the CGARCH and FIGARCH models are useful for modeling and forecasting persistence in the volatility of crude oil prices. (author)

Forecasting volatility of crude oil markets

Energy Technology Data Exchange (ETDEWEB)

Kang, Sang Hoon [Department of Business Administration, Gyeongsang National University, Jinju, 660-701 (Korea); Kang, Sang-Mok; Yoon, Seong-Min [Department of Economics, Pusan National University, Busan, 609-735 (Korea)

2009-01-15

This article investigates the efficacy of a volatility model for three crude oil markets - Brent, Dubai, and West Texas Intermediate (WTI) - with regard to its ability to forecast and identify volatility stylized facts, in particular volatility persistence or long memory. In this context, we assess persistence in the volatility of the three crude oil prices using conditional volatility models. The CGARCH and FIGARCH models are better equipped to capture persistence than are the GARCH and IGARCH models. The CGARCH and FIGARCH models also provide superior performance in out-of-sample volatility forecasts. We conclude that the CGARCH and FIGARCH models are useful for modeling and forecasting persistence in the volatility of crude oil prices. (author)

Use and declaration of additives in meat products: New legal regulations

Directory of Open Access Journals (Sweden)

Vuković Ilija

2005-01-01

Full Text Available The paper presents the more important additives used in meat products, their functional characteristics, the permitted quantities and declaration in keeping with the new legal regulations. Additives important for meat products, according to their functional characteristics, can be preservatives, antioxidants, stabilizers, emulsifiers, emulsifying salts, acidity regulators, sequestrants, thickeners, gelling agents, modified starches, acids, colours, aroma enhancers, packaging gases and coating powders, and it must be pointed out that many additives have several functional characteristics at the same time. In stating additives in the list of contents of a product, the elementary functional characteristic of the additive is given with the E number or name of the additive in brackets; modified starches are declared as „starch" without giving the E number. The declaration does not state the quantity of the additive added to the product, or the biggest permitted quantity of the additive in the given product.

Compost and Crude Humic Substances Produced from Selected Wastes and Their Effects on Zea mays L. Nutrient Uptake and Growth

Science.gov (United States)

Palanivell, Perumal; Susilawati, Kasim; Ahmed, Osumanu Haruna; Majid, Nik Muhamad

2013-01-01

Production of agriculture and timber commodities leads generation of enormous quantity of wastes. Improper disposal of these agroindustrial wastes pollutes the environment. This problem could be reduced by adding value to them. Therefore, a study was carried out to analyse and compare the nutrients content of RS, RH, SD, and EFB of composts and crude humic substances; furthermore, their effect on growth, dry matter production, and nutrient uptake for Zea mays L., and selected soil chemical properties were evaluated. Standard procedures were used to analyze humic acids (HA), crude fulvic acids (CFA), crude humin (CH), soil, dry matter production and nutrient uptake. Sawdust and RS compost matured at 42 and 47 days, respectively, while RH and EFB composts were less matured at 49th day of composting. Rice straw compost had higher ash, N, P, CEC, HA, K, and Fe contents with lower organic matter, total organic carbon, and C/N and C/P ratios. The HA of sawdust compost showed higher carbon, carboxylic, K, and Ca contents compared to those of RS, RH, and EFB. Crude FA of RS compost showed highest pH, total K, Ca, Mg, and Na contents. Crude humin from RS compost had higher contents of ash, N, P, and CEC. Rice straw was superior in compost, CFA, and CH, while sawdust compost was superior in HA. Application of sawdust compost significantly increased maize plants' diameter, height, dry matter production, N, P, and cations uptake. It also reduced N, P, and K based chemical fertilizer use by 90%. Application of CH and the composts evaluated in this study could be used as an alternative for chemical fertilizers in maize cultivation. PMID:24319353

Rate of biodegradation of crude oil by microorganisms isolated from ...

African Journals Online (AJOL)

The rate of biodegradation of crude oil by micro-organisms isolated from crude oil sludge environment in Eket, Akwa Ibom State of Nigeria was studied. Mineral salt medium supplemented with crude oil was used and three most abundant species isolated from a crude oil sludged soil - Micrococcus varians, Bacillus subtilis ...

A Microfluidic Method to Assess Emulsion Stability in Crude-Oil/Water Separators

NARCIS (Netherlands)

Krebs, T.; Schroën, C.G.P.H.; Boom, R.M.

2011-01-01

The control of emulsion stability and droplet size is of crucial importance for oil production, especially for the processes of crude/oil water separation and cleanup of produced water. To recover pure oil and water, coalescence between droplets needs to take place, the extent of which will depend

Chromatographic and spectroscopic analysis of heavy crude oil mixtures with emphasis in nuclear magnetic resonance spectroscopy: A review

International Nuclear Information System (INIS)

Silva, Sandra L.; Silva, Artur M.S.; Ribeiro, Jorge C.; Martins, Fernando G.; Da Silva, Francisco A.; Silva, Carlos M.

2011-01-01

Graphical abstract: The chromatographic and spectroscopic techniques used to characterize heavy crude oils, although more focused in the nuclear magnetic resonance spectroscopy as the technique of choice, due to its capability to provide great information on the chemical nature of individual types of proton and carbon atoms in different and complex mixtures of crude oils are described. This review is based on 65 references and describes in a critical and interpretative ways the advantages of the NMR spectroscopy as a main technique to be used in crude oil refining industries that want to characterize crude oil fractions and the obtained refined products. Highlights: ► Chromatogrfaphic and spectroscopic techniques used to characterize heavy crude oils have been reviewed. ► This review describes in a critical and interpretative ways the advantages of the NMR spectroscopy as a main technique to be used in crude oil refining industries. ► The progress in the interpretation of the NMR spectra and of different multivariate data analyses and their potential in the identification and characterization of hydrocarbons and their physical and chemical properties have also been reviewed. - Abstract: The state of the art in the characterization of heavy crude oil mixtures is presented. This characterization can be done by different techniques, such as gas chromatography (GC), high performance liquid chromatography (HPLC), thin layer chromatography (TLC), infrared spectroscopy (IR), Raman spectroscopy, nuclear magnetic resonance (NMR) spectroscopy and mass spectrometry (MS). Nuclear magnetic resonance spectroscopy is the technique of choice due to its capability to provide information on the chemical nature of individual types of hydrogen and carbon atoms in different and complex mixtures of crude oils. The progress made in the interpretation of the NMR spectra with the development of new NMR techniques and different multivariate data analyses could give relevant

Phototoxic potential of undispersed and dispersed fresh and weathered Macondo crude oils to Gulf of Mexico Marine Organisms.

Science.gov (United States)

Finch, Bryson E; Marzooghi, Solmaz; Di Toro, Dominic M; Stubblefield, William A

2017-10-01

Crude oils contain a mixture of hydrocarbons, including phototoxic polycyclic aromatic hydrocarbons (PAHs) that have the ability to absorb ultraviolet (UV) light. Absorption of UV light by PAHs can substantially increase their toxicity to marine organisms. The objective of the present study was to examine the potential for phototoxicity of fresh and naturally weathered Macondo crude oils alone and in combination with the dispersant Corexit 9500 to mysid shrimp (Americamysis bahia), inland silverside (Menidia beryllina), sheepshead minnow (Cyprinodon variegatus), and Gulf killifish (Fundulus grandis). Acute toxicity tests were conducted using combinations of natural or artificial sunlight and low-energy water-accommodated fractions (WAFs) of fresh and weathered Macondo crude oils collected from the Gulf of Mexico. Studies were also conducted to compare the phototoxicity resulting from natural and artificial sunlight. Fresh Macondo crude oil was more phototoxic than weathered crude oils, both in the presence and in the absence of UV light. Differences in toxicity between fresh and weathered crude oils were likely attributed to lighter-ringed PAHs in fresh crude oils. Phototoxic PAHs were relatively resistant to weathering compared with lighter-ringed PAHs. The addition of Corexit 9500 to crude oil increased toxicity compared with tests with crude oil alone, by increasing phototoxic PAH concentrations in WAFs. Macondo crude oils had the potential to be phototoxic to Gulf of Mexico marine organisms if specific light conditions and PAH concentrations were present during the Deepwater Horizon oil spill. Environ Toxicol Chem 2017;36:2640-2650. © 2017 SETAC. © 2017 SETAC.

Global market trade policy analysis for petroleum oils and oils obtained from bituminous minerals, crude

Directory of Open Access Journals (Sweden)

Bagheri, F.

2012-01-01

Full Text Available This article is based on surveying the custom tariffs imposed on the world export market of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. We obtained the data according to the most updated available data provided online by UNCTAD and World Bank. The results indicate that none of the 142 countries in the world market of this product have imposed non-tariff trade barriers on the import of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. The developed countries and the countries with transition economies are the main world import partners. European Union, United States, China, Japan, South Korea, Canada, Singapore, Taiwan, Thailand, South Africa, Australia, Turkey, Brazil, Sweden and Belarus are the examples and have imposed low custom tariffs on Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude.

EFFICACY OF COMMERCIAL INOCULA IN ENHANCING BIODEGRADATION OF WEATHERED CRUDE OIL CONTAMINATING A PRINCE WILLIAM SOUND BEACH

Science.gov (United States)

In a laboratory study evaluating the effectiveness of 10 commercial products in stimulating enhanced biodegradation of Alaska North Slope crude oil, two of the products provided significantly greater alkane degradation in closed flasks than indigenous Alaskan bacterial population...

Co-processing potential of HTL bio-crude at petroleum refineries

DEFF Research Database (Denmark)

Hoffmann, Jessica; Jensen, Claus Uhrenholt; Rosendahl, Lasse Aistrup

2016-01-01

assays, adapted from conventional crude oil assays, have been obtained, including fractionation of the bio-crude through 15:5 vacuum distillation. The bio-crude and its fractions have been analyzed with respect to heating value, elemental composition, density and oxygen-containing functional groups....... Results show a highly promising bio-crude quality, with a higher heating value of 40.4 MJ/kg, elemental oxygen content of 5.3 wt.%, a specific gravity of 0.97 and a distillation recovery of ∼53.4 wt.% at an atmospheric equivalent temperature (AET) of 375 °C, . Results show that only minor upgrading......This study presents detailed chemical and thermophysical analysis of bio-crude from a continuous hydrothermal liquefaction research plant. Current research on bio-crude focuses mainly on specific biomass feedstocks and conversion process conditions and resulting yields rather than on bio-crude...

Potential hazards due to food additives in oral hygiene products.

Science.gov (United States)

Tuncer Budanur, Damla; Yas, Murat Cengizhan; Sepet, Elif

2016-01-01

Food additives used to preserve flavor or to enhance the taste and appearance of foods are also available in oral hygiene products. The aim of this review is to provide information concerning food additives in oral hygiene products and their adverse effects. A great many of food additives in oral hygiene products are potential allergens and they may lead to allergic reactions such as urticaria, contact dermatitis, rhinitis, and angioedema. Dental practitioners, as well as health care providers, must be aware of the possibility of allergic reactions due to food additives in oral hygiene products. Proper dosage levels, delivery vehicles, frequency, potential benefits, and adverse effects of oral health products should be explained completely to the patients. There is a necessity to raise the awareness among dental professionals on this subject and to develop a data gathering system for possible adverse reactions.

Crude oil and natural gas supplies and demands up to the year AD 2010 for France

International Nuclear Information System (INIS)

Mackay, R.M.; Probert, S.D.

1995-01-01

A novel technique for forecasting the supply and extraction life-cycle of a depleting fossil fuel resource has been developed. The supply side utilises a 'skewed-normal production-profile' model that yields a better representation than earlier approaches. A simple model for extrapolating crude oil and natural gas demands has also been devised, based on the so called 'modified logit function'. The predicted crude oil and natural gas balances for the period up to AD 2010 indicate the disparity between indigenous production and future consumption for France. These forecasts depend on current estimates of remaining oil and gas reserves. It will consequently be necessary to revise periodically the present projections as more reliable reserve estimates become available. (author)

Production of CO2 in crude oil bioremediation in clay soil

Directory of Open Access Journals (Sweden)

Sandro José Baptista

2005-06-01

Full Text Available The aim of the present work was to evaluate the biodegradation of petroleum hydrocarbons in clay soil a 45-days experiment. The experiment was conducted using an aerobic fixed bed reactor, containing 300g of contaminated soil at room temperature with an air rate of 6 L/h. The growth medium was supplemented with 2.5% (w/w (NH42SO4 and 0.035% (w/w KH2PO4. Biodegradation of the crude oil in the contaminated clay soil was monitored by measuring CO2 production and removal of organic matter (OM, oil and grease (OandG, and total petroleum hydrocarbons (TPH, measured before and after the 45-days experiment, together with total heterotrophic and hydrocarbon-degrading bacterial count. The best removals of OM (50%, OandG (37% and TPH (45% were obtained in the bioreactors in which the highest CO2 production was achieved.O objetivo do trabalho foi avaliar a biodegradação de petróleo em solo argiloso durante 45 dias de ensaios. Os ensaios de biodegradação foram conduzidos em biorreatores aeróbios de leito fixo, com 300 g de solo contaminado, à temperatura ambiente e com uma vazão de ar de 6 L/h. As deficiências nutricionais foram corrigidas com 2,5% (p/p (NH42SO4 e com 0,035% (p/p KH2PO4. O monitoramento foi realizado em função da produção de CO2, da remoção de matéria orgânica (OM, de óleos e graxas (OandG e de hidrocarbonetos totais de petróleo (TPH, além bactérias heterotróficas totais (BHT e hidrocarbonoclásticas (BHc, no início e após 45 dias. Nos biorreatores onde houve maior crescimento de bactérias hidrocarbonoclásticas e maior produção de CO2, obteve-se os melhores percentuais de remoções de MO (50%, OandG (37% e TPH (45%.

Comparative toxicology of four crude oils

Energy Technology Data Exchange (ETDEWEB)

Clarke, L.M.; Hodson, P.V. [Queen' s Univ., Kingston, ON (Canada). Dept. of Biology; Brown, R.S. [Queen' s Univ., Kingston, ON (Canada). Dept. of Chemistry

2003-07-01

Fish that are chronically exposed to polycyclic aromatic hydrocarbons (PAHs) exhibit dioxin-like toxicity characterized by blue sac disease and the induction of cytochrome P4501A (CYP1A). This study compared the relative toxicity of four crude oils (Scotian Shelf, MESA, the synthetic Alberta Sweet Mixed Blend, and Alaskan North Slope Crude Oil), in causing the disease in rainbow trout embryos living in simulated spawning beds with hydrocarbon-contaminated gravel. Each oil had different chemical characteristics and PAH concentrations. The study confirmed the assumption that the Alberta Sweet Mixed Blend would be the most toxic due to its high PAH concentration. The results suggest that the main cause of toxicity in crude oil is due to the presence, concentration, and conformation of specific PAHs.

Crude oil options market found to be efficient

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that the U.S. crude oil options market operates efficiently and does not overreact. The authors, with the JFK School of Government, studied the crude oil options market under a Department of Energy grant. The current market was created in November 1986 when the New York Mercantile Exchange introduced an options contract for delivery of West Texas intermediate crude futures. it has grown greatly since then

Building on comparative experience : the Venezuelan extra-heavy crude oil projects

International Nuclear Information System (INIS)

Valentine, T.E.

2004-01-01

This paper reviewed legal considerations regarding heavy and extra heavy oil production in both Canada and Venezuela. The paper focused on Venezuela's extra heavy oil projects in the Orinoco Oil Belt, one of the world's largest accumulation of bitumen with an estimated reserve of 1.2 trillion barrels. The paper described the following four projects: the Petrozuata, Cerro Negro, SINCOR, and Hamaca heavy oil projects which are all congressionally approved joint ventures for extra-heavy crudes in the Orinoco Belt. It also described the legal regime which governs heavy oil projects in Venezuela, including the Organic Gaseous Hydrocarbon Law and the Organic Hydrocarbon Law. Twenty congressional conditions which have been imposed were also outlined along with the legal considerations and lessons learned regarding new extra-heavy crude projects under the two legal regimes. 1 fig

The electromechanical converter in the systems of desulfurisation of crude oil

Directory of Open Access Journals (Sweden)

Kuimov Denis

2017-01-01

Full Text Available In article authors have investigated a question of a possibility of application of hydrodynamic cavitation processing of crude oil for the purpose of decrease in content of sulphurous compounds. The electromechanical converter with a secondary discrete part, the being device exciting in the processed material the cavitation and shock field by means of heavy traffic of big set of ferromagnetic elements under the influence of external magnetic field is presented. Features of initiation of hydrodynamic cavitation on the example of the movement of a single ferromagnetic element are considered. Results of the mathematical description of process of desulphurization of crude oil are presented. On the basis of economic efficiency of the presented technological process, authors have offered options of introduction of technology on production objects.

Uncertainty & sensitivity analysis of economic assessment of lactic acid production from crude glycerol - impact of price correlations

DEFF Research Database (Denmark)

Loureiro da Costa Lira Gargalo, Carina; Carvalho, Ana; Gernaey, Krist V.

2017-01-01

In this work, we investigate the impact of the expected price volatility and correlations on the overall economic assessment of lactic acid production from crude glycerol. In particular, the goals of this study are three-fold: (i) to understand how uncertainty in the inputs propagates to the model...... outputs; (ii) to understand the effect of the degree of pairwise correlation between input uncertainties on each other and on the outputs from the economic model (Net Present Value); and lastly, (iii) to estimate the first-order as well as independent sensitivity indices so as to identify which...... of the input uncertainties in the economic analysis affect the estimated NPV the most. To this end, we implemented algorithms in Matlab (R2015a) based on Monte Carlo sampling with permutation using Latin Hypercube Sampling with Iman Conover correlation control (Sin et al., 2009).The results have shown...

POTENTIAL HAZARDS DUE TO FOOD ADDITIVES IN ORAL HYGIENE PRODUCTS

Directory of Open Access Journals (Sweden)

Damla TUNCER-BUDANUR

2016-04-01

Full Text Available Food additives used to preserve flavor or to enhance the taste and appearance of foods are also available in oral hygiene products. The aim of this review is to provide information concerning food additives in oral hygiene products and their adverse effects. A great many of food additives in oral hygiene products are potential allergens and they may lead to allergic reactions such as urticaria, contact dermatitis, rhinitis, and angioedema. Dental practitioners, as well as health care providers, must be aware of the possibility of allergic reactions due to food additives in oral hygiene products. Proper dosage levels, delivery vehicles, frequency, potential benefits, and adverse effects of oral health products should be explained completely to the patients. There is a necessity to raise the awareness among dental professionals on this subject and to develop a data gathering system for possible adverse reactions.

Selective Hydrogenolysis of Glycerol and Crude Glycerol (a By-Product or Waste Stream from the Biodiesel Industry to 1,2-Propanediol over B2O3 Promoted Cu/Al2O3 Catalysts

Directory of Open Access Journals (Sweden)

Malaya R. Nanda

2017-06-01

Full Text Available The performance of boron oxide (B2O3-promoted Cu/Al2O3 catalyst in the selective hydrogenolysis of glycerol and crude glycerol (a by-product or waste stream from the biodiesel industry to produce 1,2-propanediol (1,2-PDO was investigated. The catalysts were characterized using N2-adsorption-desorption isotherm, Inductively coupled plasma atomic emission spectroscopy (ICP-AES, X-ray diffraction (XRD, ammonia temperature programmed desorption (NH3-TPD, thermogravimetric analysis (TGA, temperature programmed reduction (TPR, and transmission electron microscopy (TEM. Incorporation of B2O3 to Cu/Al2O3 was found to enhance the catalytic activity. At the optimum condition (250 °C, 6 MPa H2 pressure, 0.1 h−1 WHSV (weight hourly space velocity, and 5Cu-B/Al2O3 catalyst, 10 wt% aqueous solution of glycerol was converted into 1,2-PDO at 98 ± 2% glycerol conversion and 98 ± 2% selectivity. The effects of temperature, pressure, boron addition amount, and liquid hourly space velocity were studied. Different grades of glycerol (pharmaceutical, technical, or crude glycerol were used in the process to investigate the stability and resistance to deactivation of the selected 5Cu-B/Al2O3 catalyst.

Contents of lecithin and choline in crude drugs.

Science.gov (United States)

Yamasaki, K; Kikuoka, M; Nishi, H; Kokusenya, Y; Miyamoto, T; Matsuo, M; Sato, T

1994-01-01

The determination of lecithin and choline in crude drugs was established by a combination of high performance liquid chromatography (HPLC) with electrochemical detector (ECD) and enzyme reaction. Lecithin in crude drugs extracted with a mixture of chloroform-methanol (2:1) at room temperature was hydrolyzed by phospholipase D. The hydrolyzate was injected to HPLC, and choline was separated from impurities by reverse phase column. The choline was converted to betaine and hydrogen peroxide by passing through column packed with immobilized choline oxidase. This hydrogen peroxide was detected by ECD. The peak area of hydrogen peroxide derived from lecithin was proportional to the concentration of lecithin from 0.10 to 1.52 microgram/ml. Choline in crude drugs was extracted with ethanol under reflux and determined under the same HPLC conditions as lecithin. The peak area of hydrogen peroxide derived from choline was proportional to the concentration of choline from 0.01 to 0.45 microgram/ml. The contents of lecithin and choline in 31 kinds of crude drugs were determined by these established methods. The results showed that Cervi Parvum Cornu, Kokurozin, Foenigraeci Semen and Psoraleae Semen contained more lecithin than other crude drugs, while Angelicae Radix, Foenigraeci Semen, Psoraleae Semen, and especially Hippocampus were found to contain more choline than other crude drugs.

When Will Occur the Crude Oil Bubbles?

International Nuclear Information System (INIS)

Su, Chi-Wei; Li, Zheng-Zheng; Chang, Hsu-Ling; Lobonţ, Oana-Ramona

2017-01-01

In this paper, we apply a recursive unit root test to investigate whether there exist multiple bubbles in crude oil price. The method is best suited for a practical implementation of a time series and delivers a consistent date-stamping strategy for the origination and termination of multiple bubbles. The empirical result indicates that there exist six bubbles during 1986–2016 when the oil price deviate from its intrinsic value based on market fundamentals. Specifically, oil price contains the fundamentals and bubble components. The dates of the bubbles correspond to specific events in the politics and financial markets. The authorities should actively fight speculative bubbles or just observe their evolutions and speculation activities may decrease, which is favour of the stabilisation of the staple commodities including crude oil price. These findings have important economic and policy implications to recognise the cause of bubbles and take corresponding measures to reduce the impact on the real economy cause of the fluctuation of crude oil price. - Highlights: • Investigate multiple bubbles in crude oil price. • Indicate six bubbles deviate from its intrinsic value based on market fundamentals. • The bubbles correspond to specific events in the politics and financial markets. • Reduce the impact on the real economy cause of the fluctuation of crude oil price.

Contribution de la pyrolyse des produits lourds à la valorisation des pétroles bruts Contribution of the Pyrolysis of Heavy Products to the Upgrading of Crude Oils

Directory of Open Access Journals (Sweden)

Charlot J. C.

2006-11-01

Full Text Available Le raffineur achète des pétroles bruts, de différentes qualités et d'origines variées, et il fabrique un certain nombre de produits répondant à des spécifications de qualité pour les vendre dans des proportions correspondant aux besoins du marché. Il est nécessaire pour cela d'assurer l'équilibre général entre l'approvisionnement en brut et la demande du marché en produits finis. Les facteurs traduisant l'évolution des pétroles bruts (souci de diversification géographique et politique, désir des producteurs de traiter les bruts faciles et d'exporter les lourds, compétitivité de plus en plus grande des bruts non-conventionnels, grande disponibilité d'huiles lourdes montrent l'alourdissement progressif des approvisionnements. L'enchérissement des produits pétroliers provoque de plus en plus un allègement des besoins du marché (légère augmentation des carburants, baisse des distillats moyens, chute importante des fuels lourds. Du fait de l'alourdissement des bruts conventionnels, de la grande disponibilité des huiles lourdes et de l'allègement considérable du marché des produits finis, il devient nécessaire d'utiliser des charges de plus en plus lourdes dans les procédés de conversion. La production d'oléfines peut s'effectuer à partir d'une gamme très large de coupes pétrolières, mais lorsqu'on cherche à alourdir la charge des unités de pyrolyse, il faut se poser les questions suivantes : - quelle est la souplesse des unités existantes et à venir par rapport à la charge ? - quelle est la limite industrielle et l'alourdissement de la charge ? - quel est le rôle des impuretés sur le fonctionnement des unités ? - quels sont les problèmes technologiques posés par le traitement de ces charges ? - qu'en est-il de l'amélioration des bilans énergétiques et économiques lorsque la charge s'alourdit ? A refiner buys crude oils of different qualities and varying origins and he manufactures a certain number

Bioremediation of crude oil contaminated tea plantation soil using ...

African Journals Online (AJOL)

Crude oil contamination of soil is a major concern for tea industry in Assam, India. Crude oil is a persistent organic contaminant which alters soil physical and biochemical characteristics and makes tea plants more susceptible against crude oil contamination. Therefore, two native bacterial strains designated as AS 03 and ...

Crude oil and finished fuel storage stability: An annotated review

Energy Technology Data Exchange (ETDEWEB)

Whisman, M.L.; Anderson, R.P.; Woodward, P.W.; Giles, H.N.

1991-01-01

A state-of-the-art review and assessment of storage effects on crude oil and product quality was undertaken through a literature search by computer accessing several data base sources. Pertinent citations from that literature search are tabulated for the years 1980 to the present. This 1990 revision supplements earlier reviews by Brinkman and others which covered stability publications through 1979 and an update in 1983 by Goetzinger and others that covered the period 1952--1982. For purposes of organization, citations are listed in the current revision chronologically starting with the earliest 1980 publications. The citations have also been divided according to primary subject matter. Consequently 11 sections appear including: alternate fuels, gasoline, distillate fuel, jet fuel, residual fuel, crude oil, biodegradation, analyses, reaction mechanisms, containment, and handling and storage. Each section contains a brief narrative followed by all the citations for that category.

Optimization of factors affecting the production of biodiesel from crude palm kernel oil and ethanol

Energy Technology Data Exchange (ETDEWEB)

Kuwornoo, David. K. [Faculty of Chemical and Materials Engineering, Kwame Nkrumah University of Science and Technology (KNUST), Private Mail Bag, Kumasi (Ghana); Ahiekpor, Julius C. [Chemical Engineering Department, Kumasi Polytechnic, P.O. Box 854, Kumasi (Ghana)

2010-07-01

Biodiesel, an alternative diesel fuel made from renewable sources such as vegetable oils and animal fats, has been identified by government to play a key role in the socio-economic development of Ghana. The utilization of biodiesel is expected to be about 10% of the total liquid fuel mix of the country by the year 2020. Despite this great potential and the numerous sources from which biodiesel could be developed in Ghana, studies on the sources of biodiesel and their properties as a substitute for fossil diesel have tended to be limited to Jatropha oil. This paper, however, reports the parameters that influences the production of biodiesel from palm kernel oil, one of the vegetable oils obtained from oil palm which is the highest vegetable oil source in Ghana. The parameters studied are; mass ratio of ethanol to oil, reaction temperature, catalyst concentration, and reaction time using completely randomized 24 factorial design. Results indicated that ethanol to oil mass ratio, catalyst concentration and reaction time were the most important factors affecting the ethyl ester yield. There was also an interaction effect between catalyst and time and ethanol- oil ratio and time on the yield. Accordingly, the optimal conditions for the production of ethyl esters from crude palm kernel oil were determined as; 1:5 mass ratio of ethanol to oil, 1% catalyst concentration by weight of oil, 90 minutes reaction time at a temperature of 30 deg C.

Application of Multivariate Statistical Analysis to Biomarkers in Se-Turkey Crude Oils

Science.gov (United States)

Gürgey, K.; Canbolat, S.

2017-11-01

Twenty-four crude oil samples were collected from the 24 oil fields distributed in different districts of SE-Turkey. API and Sulphur content (%), Stable Carbon Isotope, Gas Chromatography (GC), and Gas Chromatography-Mass Spectrometry (GC-MS) data were used to construct a geochemical data matrix. The aim of this study is to examine the genetic grouping or correlations in the crude oil samples, hence the number of source rocks present in the SE-Turkey. To achieve these aims, two of the multivariate statistical analysis techniques (Principle Component Analysis [PCA] and Cluster Analysis were applied to data matrix of 24 samples and 8 source specific biomarker variables/parameters. The results showed that there are 3 genetically different oil groups: Batman-Nusaybin Oils, Adıyaman-Kozluk Oils and Diyarbakir Oils, in addition to a one mixed group. These groupings imply that at least, three different source rocks are present in South-Eastern (SE) Turkey. Grouping of the crude oil samples appears to be consistent with the geographic locations of the oils fields, subsurface stratigraphy as well as geology of the area.

APPLICATION OF MULTIVARIATE STATISTICAL ANALYSIS TO BIOMARKERS IN SE-TURKEY CRUDE OILS

Directory of Open Access Journals (Sweden)

K. Gürgey

2017-11-01

Full Text Available Twenty-four crude oil samples were collected from the 24 oil fields distributed in different districts of SE-Turkey. API and Sulphur content (%, Stable Carbon Isotope, Gas Chromatography (GC, and Gas Chromatography-Mass Spectrometry (GC-MS data were used to construct a geochemical data matrix. The aim of this study is to examine the genetic grouping or correlations in the crude oil samples, hence the number of source rocks present in the SE-Turkey. To achieve these aims, two of the multivariate statistical analysis techniques (Principle Component Analysis [PCA] and Cluster Analysis were applied to data matrix of 24 samples and 8 source specific biomarker variables/parameters. The results showed that there are 3 genetically different oil groups: Batman-Nusaybin Oils, Adıyaman-Kozluk Oils and Diyarbakir Oils, in addition to a one mixed group. These groupings imply that at least, three different source rocks are present in South-Eastern (SE Turkey. Grouping of the crude oil samples appears to be consistent with the geographic locations of the oils fields, subsurface stratigraphy as well as geology of the area.

Separated influence of crude oil prices on regional natural gas import prices

International Nuclear Information System (INIS)

Ji, Qiang; Geng, Jiang-Bo; Fan, Ying

2014-01-01

This paper analyses the impact of global economic activity and international crude oil prices on natural gas import prices in three major natural gas markets using the panel cointegration model. It also investigates the shock impacts of the volatility and the increase and decrease of oil prices on regional natural gas import prices. The results show that both global economic activity and international crude oil prices have significant long-term positive effects on regional natural gas import prices. The volatility of international crude oil prices has a negative impact on regional natural gas import prices. The shock impact is weak in North America, lags in Europe and is most significant in Asia, which is mainly determined by different regional policies for price formation. In addition, the response of natural gas import prices to increases and decreases in international crude oil prices shows an asymmetrical mechanism, of which the decrease impact is relatively stronger. - Highlights: • Impacts of world economy and oil prices on regional natural gas prices are analysed • North American natural gas prices are mainly affected by world economy • Asian and European natural gas prices are mainly affected by oil prices • The volatility of oil prices has a negative impact on regional natural gas prices • The response of natural gas import prices to oil prices up and down shows asymmetry

Developing new markets for oil sands products

International Nuclear Information System (INIS)

Crandall, G.

2004-01-01

This paper presents a review by Purvin and Gertz of western Canadian crude oil supply. This energy consulting firm provides advise to the energy sector. It suggests that oil sands production will surpass declining conventional production. Oil sands supply includes bitumen, synthetic crude oil (SCO), and diluent. It is forecasted that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. The potential of Alberta's oil sands was discussed along with a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. The author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. 15 figs

Review of Alberta Crown Crude Oil Marketing Program

International Nuclear Information System (INIS)

Crandall, G. R.; Kromm, R. B.

1999-01-01

This report contains an independent evaluation of the operations of the private marketing agents that are currently marketing the Alberta Crown's share of royalty crude oil. The evaluation includes a review of pricing performance, working relationship, current issues and the overall performance of the marketing arrangements during the fiscal years of 1997 and 1998. Overall, the outsourcing of sales of Crown production to agents is judged to be successful. For example, it has been noted that agents are becoming more aggressive in maintaining and increasing their margins. On the other hand, the increased level of aggressiveness in marketing, while tending to maximize Crown revenues, is also creating a potential conflict on how margins should be shared between the Crown and its agents. Also, there has been evidence of some management issues between the agents and the Crown concerning the extent to which the Crown should share in any increased value which the agent generates by increased third party marketing activities. These differences need to be addressed in order to maintain the strong performance of the marketing program. The consultants also recommend additional guidelines on risk management issues that more clearly define the Crown's risk tolerance. 2 tabs., 4 figs

Modulation of platelet functions by crude rice (Oryza sativa) bran policosanol extract.

Science.gov (United States)

Wong, Wai-Teng; Ismail, Maznah; Imam, Mustapha Umar; Zhang, Yi-Da

2016-07-28

Rice bran is bioactive-rich and has proven health benefits for humans. Moreover, its source, the brown rice has antioxidant, hypolipidemic and other functional properties that are increasingly making it a nutritional staple especially in Asian countries. This study investigated the antiplatelet aggregation mechanisms of crude hexane/methanolic rice bran extract, in which policosanol was the targeted bioactive. Platelets play a vital role in pathogenesis of atherosclerosis and cardiovascular diseases, and their increased activities could potentially cause arterial thrombus formation or severe bleeding disorders. Thus, in this study, platelet aggregation and adhesion of platelets to major components of basal lamina were examined in vitro. In addition, cellular protein secretion was quantified as a measurement of platelet activation. Adenosine diphosphate (ADP), collagen, and arachidonic acid (AA)-induced aggregation were studied using the microtiter technique. Rat platelets were pre-treated with various concentrations of policosanol extract, and the adhesion of platelets onto collagen- and laminin-coated surface (extracellular matrix) was studied using the acid phosphatase assay. The effect of crude policosanol extract on released proteins from activated platelets was measured using modified Lowry determination method. Rice bran policosanol extract significantly inhibited in vitro platelet aggregation induced by different agonists in a dose dependent manner. The IC50 of ADP-, collagen-, and AA-induced platelet aggregation were 533.37 ± 112.16, 635.94 ± 78.45 and 693.86 ± 70.57 μg/mL, respectively. The present study showed that crude rice bran policosanol extract significantly inhibited platelet adhesion to collagen in a dose dependent manner. Conversely, at a low concentration of 15.625 μg/mL, the extract significantly inhibited platelet adhesion to laminin stimulated by different platelet agonists. In addition to the alteration of cell adhesive

Rheological Behaviour of Water-in-Light Crude Oil Emulsion

Science.gov (United States)

Husin, H.; Taju Ariffin, T. S.; Yahya, E.

2018-05-01

Basically, emulsions consist of two immiscible liquids which have different density. In petroleum industry, emulsions are undesirable due to their various costly problems in term of transportation difficulties and production loss. A study of the rheological behaviour of light crude oil and its mixture from Terengganu were carried out using Antoon Paar MCR 301 rheometer operated at pressure of 2.5 bar at temperature C. Water in oil emulsions were prepared by mixing light crude oil with different water volume fractions (20%, 30% and 40%). The objectives of present paper are to study the rheological behaviour of emulsion as a fuction of shear rate and model analysis that fitted with the experimental data. The rheological models of Ostwald-De-Waele and Herschel-Bulkley were fitted to the experimental results. All models represented well the rheological data, with high values for the correlation coefficients. The result indicated that variation of water content influenced shear rate-shear stress rheogram of the prepared emulsions. In the case of 100% light crude oil, the study demonstrated non-Newtonian shear thickening behavior. However, for emulsion with different volume water ratios, the rheological behaviour could be well described by Herschel-Bulkley models due to the present of yield stress parameter (R2 = 0.99807). As a conclusion, rheological studies showed that volume water ratio have a great impact on the shear stress and viscosity of water in oil emulsion and it is important to understand these factors to avoid various costly problems.

Detection by denaturing gradient gel electrophoresis of ammonia-oxidizing bacteria in microcosms of crude oil-contaminated mangrove sediments.

Science.gov (United States)

dos Santos, A C F; Marques, E L S; Gross, E; Souza, S S; Dias, J C T; Brendel, M; Rezende, R P

2012-01-27

Currently, the effect of crude oil on ammonia-oxidizing bacterium communities from mangrove sediments is little understood. We studied the diversity of ammonia-oxidizing bacteria in mangrove microcosm experiments using mangrove sediments contaminated with 0.1, 0.5, 1, 2, and 5% crude oil as well as non-contaminated control and landfarm soil from near an oil refinery in Camamu Bay in Bahia, Brazil. The evolution of CO(2) production in all crude oil-contaminated microcosms showed potential for mineralization. Cluster analysis of denaturing gradient gel electrophoresis-derived samples generated with primers for gene amoA, which encodes the functional enzyme ammonia monooxygenase, showed differences in the sample contaminated with 5% compared to the other samples. Principal component analysis showed divergence of the non-contaminated samples from the 5% crude oil-contaminated sediment. A Venn diagram generated from the banding pattern of PCR-denaturing gradient gel electrophoresis was used to look for operational taxonomic units (OTUs) in common. Eight OTUs were found in non-contaminated sediments and in samples contaminated with 0.5, 1, or 2% crude oil. A Jaccard similarity index of 50% was found for samples contaminated with 0.1, 0.5, 1, and 2% crude oil. This is the first study that focuses on the impact of crude oil on the ammonia-oxidizing bacterium community in mangrove sediments from Camamu Bay.

A laboratory study of particulate and gaseous emissions from crude oil and crude oil-dispersant contaminated seawater due to breaking waves

Science.gov (United States)

Afshar-Mohajer, Nima; Li, Cheng; Rule, Ana M.; Katz, Joseph; Koehler, Kirsten

2018-04-01

Crude oil spill incidents occur frequently causing a verity of occupational, ecological and environmental problems. Dispersants are applied to enhance the dispersion rate of crude oil slicks into the water column. In this study, the aerosol size distribution from 10 nm to 20 μm, total particle-bound aromatic hydrocarbons (pPAH) and volatile organic compounds (VOCs) are measured in a 6 x 0.3 x 0.6 m tank as plunging breaking waves entrain oil slicks. The experiments are performed for seawater with slicks of crude oil, crude oil-dispersant mixture and dispersant only. The measurements investigate the effects of wave energy and slick properties on the temporal evolution of the emissions. The total number concentrations of particles originating from the oil-dispersant mixture are 1-2 orders of magnitude higher than those of crude oil across the entire nano-scale range, reaching 100x for 20 nm particles. Conversely, the differences in concentration are small in the micron range. The average concentrations of pPAH are variable but similar (150-270 ng/m3). The VOC concentrations for crude oil-dispersant mixtures are 2-3 times lower than those of crude oil, presumably due to the surfactant effect on mass diffusion. The drastic increase in ultrafine particle concentrations may raise concerns about effects of inhalation by cleanup workers and downstream communities though VOC emissions reduce. Findings through this study provide insight into how the spray of dispersant may change the ratio of airborne particulate matter and VOC emissions from seawater due to natural processes.

Bioremediation potential of a tropical soil contaminated with a mixture of crude oil and production water.

Science.gov (United States)

Alvarez, Vanessa Marques; Santos, Silvia Cristina Cunha Dos Santos; Casella, Renata da Costa; Vital, Ronalt Leite; Sebastin, Gina Vasquez; Seldin, Lucy

2008-12-01

A typical tropical soil from the northeast of Brazil, where an important terrestrial oil field is located, was accidentally contaminated with a mixture of oil and saline production water. To study the bioremediation potential in this area, molecular methods based on PCR-DGGE were used to determine the diversity of the bacterial communities in bulk and in contaminated soils. Bacterial fingerprints revealed that the bacterial communities were affected by the presence of the mixture of oil and production water, and different profiles were observed when the contaminated soils were compared with the control. Halotolerant strains capable of degrading crude oil were also isolated from enrichment cultures obtained from the contaminated soil samples. Twenty-two strains showing these features were characterized genetically by amplified ribosomal DNA restriction analysis (ARDRA) and phenotypically by their colonial morphology and tolerance to high NaCl concentrations. Fifteen ARDRA groups were formed. Selected strains were analyzed by 16S rDNA sequencing, and Actinobacteria was identified as the main group found. Strains were also tested for their growth capability in the presence of different oil derivatives (hexane, dodecane, hexadecane, diesel, gasoline, toluene, naphthalene, o-xylene, and p-xylene) and different degradation profiles were observed. PCR products were obtained from 12 of the 15 ARDRA representatives when they were screened for the presence of the alkane hydroxylase gene (alkB). Members of the genera Rhodococcus and Gordonia were identified as predominant in the soil studied. These genera are usually implicated in oil degradation processes and, as such, the potential for bioremediation in this area can be considered as feasible.

Evaluation of methods for wax determination in crude oil; Avaliacao de metodos de determinacao de parafinas em petroleo

Energy Technology Data Exchange (ETDEWEB)

Dias, Julio Cesar M.; Silva, Maria do Socorro A.J. da; Vasconcellos, Rosa C.U. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas; Tamanqueira, Juliana B. [Fundacao Gorceix, Ouro Preto, MG (Brazil)

2008-07-01

Determining the wax content of crude oil is of great importance for petroleum industry, especially for production, storage and transportation of crude oils. Many different methodologies of wax determining are available in the technical literature. However, the selection of the most suitable method must be in accordance with the aim of the analysis and observing the specificities of each technique. The purpose of this work was to determine the performance of different techniques of wax determining applied to characterization of precipitation properties of waxy compounds in crude oils. Twelve samples of crude oils proceeding from the main Brazilian oil producing sedimentary basins were selected for this study. These samples were analyzed by three important analytical techniques of wax determining: precipitation by cooled solvent; liquid chromatography with precipitation by cooled solvent; and liquid chromatography followed by gas chromatography. Differential scanning calorimetry data related to the wax crystallization in these oils were used as parameters of validation. The results obtained in this study indicate that the liquid chromatography followed by gas chromatography method has the best performance for wax determining in crude oils. (author)

Enhanced crude oil biodegradation in soil via biostimulation.

Science.gov (United States)

Al-Saleh, Esmaeil; Hassan, Ali

2016-08-02

Research on feasible methods for the enhancement of bioremediation in soil contaminated by crude oil is vital in oil-exporting countries such as Kuwait, where crude oil is a major pollutant and the environment is hostile to biodegradation. This study investigated the possibility of enhancing crude oil bioremediation by supplementing soil with cost-effective organic materials derived from two widespread locally grown trees, Conocarpus and Tamarix. Amendments in soils increased the counts of soil microbiota by up to 98% and enhanced their activity by up to 95.5%. The increase in the biodegradation of crude oil (75%) and high levels of alkB expression substantiated the efficiency of the proposed amendment technology for the bioremediation of hydrocarbon-contaminated sites. The identification of crude-oil-degrading bacteria revealed the dominance of the genus Microbacterium (39.6%), Sphingopyxis soli (19.3%), and Bordetella petrii (19.6%) in unamended, Conocarpus-amended, and Tamarix-amended contaminated soils, respectively. Although soil amendments favored the growth of Gram-negative bacteria and reduced bacterial diversity, the structures of bacterial communities were not significantly altered.

Evaluation of the efficiency of silicone polyether additives as foam inhibitor in crude oil

International Nuclear Information System (INIS)

Fraga, Assis K.; Santos, Raquel F.; Mansur, Claudia R.E.

2011-01-01

This work evaluates the chemical and physico-chemical properties of commercial anti-foam products based on silicone polyethers along with their efficiency in inhibiting foaming. The commercial surfactants were characterized by nuclear magnetic resonance (NMR) spectroscopy, size exclusion chromatography (SEC), determination of solubility in different solvents and measurement of the surface and interfacial tensions. A method to test the formation of foam in oil was used to mimic the operating conditions in gas-oil separators. The results show that the most polar additive was the most efficient in breaking up the foam. (author)

Three essays in corporate finance: Examining the influence of government ownership and evaluating crude oil arbitrage

Science.gov (United States)

Holland, Kateryna

The aim of this dissertation is twofold: first, to evaluate how governments influence firms in which they invest (chapters one and two), and second, to examine arbitrage in the crude oil market by investigating the relationship between crude oil inventories, physical prices, and financial prices (chapter three). In the first chapter (The Wealth Effects of Government Investment in Publicly Traded Firms), I study how government share ownership affects shareholder wealth. I find that government investments with higher likelihood of political interference have a negative influence on shareholder wealth, while the opposite is true for government investments with economic objectives. In the second chapter (Government Ownership and the Cost of Debt: Evidence form Government Investment in Publicly Traded Firms), I investigate how government share ownership affects the cost of debt of publicly traded firms. I find that government ownership generally leads to a higher cost of debt, except for times of economic and firm distress, when the value of the implicit government guarantee is associated with a reduction in the cost of debt. In the third chapter (Financial Trading, Spot Oil Prices, and Inventory: Evidence from the U.S. Crude Oil Market), I confirm the existence of an active cash and carry market in crude oil in Cushing, OK, the main U.S. crude oil futures settlement location. In other words, crude oil inventories in Cushing, but not in any other U.S. crude oil storage locations, are explained by the spread between the financial and the physical price of oil in addition to operational factors.

Experimental Study on Characteristics of Oil Particle Distribution in Water-Gelled Crude Oil Two-Phase Flow System

Directory of Open Access Journals (Sweden)

Liu Xiaoyan

2014-06-01

Full Text Available The conventional gathering and transportation mode of heating the produced fluid of oil wells with hot water or steam may result in excessive energy consumption. In order to perform the unheated transportation, the idea of hydraulic suspension transport of the gelled crude oil is proposed based on the actual production of Daqing Oilfield, and the experimental system is established to test characteristics of oil particle distribution which have an important effect on the hydraulic suspension transportation. In the experiment, the image of gelled crude oil particle distribution was obtained in a horizontal pipe with inner diameter of 0.053 m, and then the law of particle distribution was investigated by the theoretical model. The results showed that the gelled crude oil hydraulic suspension transport could be achieved without any chemical reagent when the gelled crude oil was transformed into particles and dispersedly suspended in water. The results also showed that the gelled oil particles of 0–4 mm in size accounted for 92% or more of all particles, and the percentage of gelled crude oil particles of a size of 4 mm gradually increased with the increasing mixed flow rate.

Assessment of Antioxidant Indices after incorporating Crude Oil ...

African Journals Online (AJOL)

ADOWIE PERE

Exposure to crude oil pollution leads to the formation ... vitamin/mineral mixture (5 %). The food ..... hepatic antioxidant enzymes against cadmium induced liver ... Interaction of crude oil with alpha-tocopherol: ... Essential oil from Monodora.

[Comparison of anti-inflammatory activity between crude Atractylodes lancea and their processed products by stir-baking with bran in rat models of gastric ulcer].

Science.gov (United States)

Yu, Yan; Jia, Tian-Zhu; Cai, Qian

2016-02-01

To compare the anti-inflammatory activity of the crude Atractylodes lancea (AL) and AL processed products by stir-baking with bran in rat models of gastric ulcer, and preliminarily explore the anti-ulcer mechanisms of AL, the model of gastric ulcer was imitated by local acetic acid injection into gastric mucosa in rats by surgery according to the modified Okabe method. All rats were randomly divided into the following 10 groups： sham-operation group, model group, omeprazole group, Sanjiu Weitai granule group, crude AL low dose group, crude AL middle dose group, crude AL high dose group, processed AL low dose group, processed AL middle dose group, and processed AL high dose group. Rats were administered via intragastric (ig) two times each day, for 10 consecutive days. Blood was collected from the abdominal aorta, serum was separated, and the ulcer tissues were taken. The levels of inflammatory factors interleukin 6, 8 (IL-6, 8), tumor necrosis factor-α (TNF-α), and prostaglandin E2 (PGE2) in serum and gastric tissues were determined by enzyme-linked immunosorbent assay (ELISA), and the mRNA expressions of TNF-α and IL-8 in gastric tissues were detected by quantitative real-time reverse transcription polymerase chain reaction (RT-PCR). The protein expressions of TNF-α and IL-8 in gastric tissues were detected by immunohistochemistry. Compared with sham-operation group, the levels of TNF-α, IL-8, IL-6, PGE2 as well as the mRNA expressions and protein expressions of TNF-α, IL-8 in gastric tissues were significantly higher in model group. The above levels were reduced in different degrees in all treatment groups. Compared with the crude AL, same dose of processed AL was more effective in decreasing the levels of TNF-α, IL-8, IL-6, PGE2 in serum and gastric tissues and down-regulating the mRNA expressions of TNF-α and IL-8 in gastric tissues, with significant difference in middle dose groups and high dose groups. The results showed that AL had potent anti

Ingestive behavior of grazing heifers receiving crude glycerin supplementation during the dry-rainy season transition

Directory of Open Access Journals (Sweden)

Vitor Visintin Silva de Almeida

2014-09-01

Full Text Available The search to find food alternatives for corn and feeding alternatives that reduce the cost of production has been constant. The use of oleaginous grains to produce ethanol and biodiesel has produced an excess of byproducts, especially biodiesel which produces crude glycerin. The objective of this study was to evaluate the effect of including crude glycerin on the ingestive behavior of crossbred heifers supplemented with pasture. Thirty-six crossbred heifers with an initial mean weight of 301.5 ± 31 kg were distributed in a completely randomized design with four treatments and nine replicates per treatment. The animals were kept in a Brachiaria brizantha (Hochst. ex A. Rich. Stapf 'Marandu' pasture in a rotational-grazing system. The treatments tested were 0.0%, 3.33%, 6.66%, and 9.99% crude glycerin included in total DM to replace corn (Tea mays L. Including crude glycerin reduced the time for grazing and eating at the trough and increased idle time. Rumination was quadratically influenced. Eating time (min kg-1 DM and neutral detergent fiber [NDF] was reduced, while rumination time (min kg-1 DM and NDF was quadratically affected by adding glycerin. The variables, time spent per ruminated bolus and the number of chews per day, were not affected. The number of boluses per day showed a quadratic effect. The number of grazing, idle, ruminating, and eating at the trough periods were not affected by including crude glycerin; means were 15.1, 24.9, and 13.3 and 3.71 periods d-1, respectively. Feed and rumination efficiency (kg h-1 DM and NDF increased when crude glycerin was included in the diet. Including crude glycerin promotes feed and rumination efficiency in grazing heifers.

Waxy crude oil flow restart ability

Energy Technology Data Exchange (ETDEWEB)

Sierra, Andre Gaona; Varges, Priscilla Ribeiro; Mendes, Paulo Roberto de Souza [Dept. of Mechanical Engineering. Pontificia Universidade Catolica do Rio de Janeiro, RJ (Brazil)], e-mails: prvarges@puc-rio.br, pmendes@puc-rio.br; Ziglio, Claudio [PETROBRAS S.A, R.J., Rio de Janeiro, RJ (Brazil)], e-mail: ziglio@petrobras.com.br

2010-07-01

Under the hot reservoir conditions, waxy crudes behave like Newtonian fluids but once they experience very cold temperatures on the sea floor, the heavy paraffin's begin to precipitate from the solution impacting non- Newtonian flow behavior to the crude (Chang 2000, Lee 2009, Davidson 2004) and begin to deposit on the pipe wall leave blocked of pipeline. This gel cannot be broken with the original steady state flow operating pressure applied before gelation (Chang 1998). Restarting waxy crude oil flows in pipelines is a difficult issue because of the complex rheological behavior of the gelled oil. Indeed, below the WAT, the gelled oil exhibits viscoplastic, thixotropic, temperature-dependent, and compressible properties due to the interlocking gel-like structure formed by the crystallized paraffin compounds and the thermal shrinkage of the oil. The main objective of this work is to determine the minimal pressure to restart the flow, and the relationship between the fluid rheology , pipe geometry and the restart pressure of the flow. Experiments will be performed to investigate the displacement of carbopol aqueous solutions (viscoplastic fluid without thixotropic effects) by Newtonian oil flowing through a strait pipe to validate the experimental apparatus. Therefore, tests will be made with different fluids, like Laponite and waxy crude oils. (author)

Effect of crude oil contamination on the chlorophyll content and morpho-anatomy of Cyperus brevifolius (Rottb.) Hassk.

Science.gov (United States)

Baruah, Plabita; Saikia, Rashmi Rekha; Baruah, Partha Pratim; Deka, Suresh

2014-11-01

Chlorophyll plays a pivotal role in the plant physiology and its productivity. Cultivation of plants in crude oil contaminated soil has a great impact on the synthesis of chlorophyll pigment. Morpho-anatomy of the experimental plant also shows structural deformation in higher concentrations. Keeping this in mind, a laboratory investigation has been carried out to study the effect of crude oil on chlorophyll content and morpho-anatomy of Cyperus brevifolius plant. Fifteen-day-old seedling of the plant was planted in different concentrations of the crude oil mixed soil (i.e., 10,000, 20,000, 30,000, 40,000, and 50,000 ppm). A control setup was also maintained without adding crude oil. Results were recorded after 6 months of plantation. Investigation revealed that there is a great impact of crude oil contamination on chlorophyll content of the leaves of the experimental plant. It also showed that chlorophyll a, chlorophyll b, and total chlorophyll content of leaves grown in different concentrations of crude oil were found to be lower than those of the control plant. Further, results also demonstrated that chlorophyll content was lowest in the treatment that received maximum dose of crude oil. It also showed that chlorophyll content was decreased with increased concentration of crude oil. Results also demonstrated that there was a reduction in plant shoot and root biomass with the increase of crude oil concentration. Results also revealed that the shoot biomass is higher than root biomass. Morphology and anatomy of the experimental plant also show structural deformation in higher concentrations. Accumulation of crude oil on the cuticle of the transverse section of the leaves and shoot forms a thick dark layer. Estimation of the level of pollution in an environment due to oil spill is possible by the in-depth study of the harmful effects of oil on the morphology and anatomy and chlorophyll content of the plants grown in that particular environment.

Biomass and lipid production of Chlorella protothecoides under heterotrophic cultivation on a mixed waste substrate of brewer fermentation and crude glycerol.

Science.gov (United States)

Feng, Xiaoyu; Walker, Terry H; Bridges, William C; Thornton, Charles; Gopalakrishnan, Karthik

2014-08-01

Biomass and lipid accumulation of heterotrophic microalgae Chlorella protothecoides by supplying mixed waste substrate of brewer fermentation and crude glycerol were investigated. The biomass concentrations of the old and the new C. protothecoides strains on day 6 reached 14.07 and 12.73 g/L, respectively, which were comparable to those in basal medium with supplement of glucose and yeast extract (BM-GY) (14.47 g/L for old strains and 11.43 g/L for new strains) (P>0.05). Approximately 81.5% of total organic carbon and 65.1% of total nitrogen in the mixed waste were effectively removed. The accumulated lipid productivities of the old and the new C. protothecoides strains in BM-GY were 2.07 and 1.61 g/L/day, respectively, whereas in the mixed waste, lipid productivities could reach 2.12 and 1.81 g/L/day, respectively. Our result highlights a new approach of mixing carbon-rich and nitrogen-rich wastes as economical and practical alternative substrates for biofuel production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of the addition of chia's by-product on the composition of fatty acids in hamburgers through chemometric methods.

Science.gov (United States)

Souza, Aloisio H P; Gohara, Aline K; Rotta, Eliza M; Chaves, Marcia A; Silva, Claudia M; Dias, Lucia F; Gomes, Sandra T M; Souza, Nilson E; Matsushita, Makoto

2015-03-30

Hamburger is a meat-based food that is easy to prepare and is widely consumed. It can be enriched using different ingredients, such as chia's by-product, which is rich in omega-3. Chemometrics is a very interesting tool to assess the influence of ingredients in the composition of foods. A complete factorial design 2(2) (two factors in two levels) with duplicate was performed to investigate the influence of the factors (1) concentration of textured soy proteins (TSP) and (2) concentration of chia flour partially defatted (CFPD) as a partial replacement for the bovine meat and porcine fat mix in hamburgers. The results of proximal composition, lipid oxidation, fatty acids sums, ratios, and nutritional indexes were used to propose statistical models. The factors TSP and CFPD were significant, and the increased values contributed to improve the composition in fatty acids, crude protein, and ash. Principal components analysis distinguished the samples with a higher content of chia. In desirability analysis, the highest level of TSP and CFPD was described as the optimal region, and it was not necessary to make another experimental point. The addition of chia's by-product is an alternative to increase the α-linolenic contents and to obtain nutritionally balanced food. © 2014 Society of Chemical Industry.

Identification of flavour additives in tobacco products to develop a flavour library

Science.gov (United States)

Krüsemann, Erna JZ; Visser, Wouter F; Cremers, Johannes WJM; Pennings, Jeroen LA; Talhout, Reinskje

2018-01-01

Objectives This study combines chemical analysis and flavour descriptions of flavour additives used in tobacco products, and provides a starting point to build an extensive library of flavour components, useful for product surveillance. Methods Headspace gas chromatography-mass spectrometry (GC-MS) was used to compare 22 commercially available tobacco products (cigarettes and roll-your-own) expected to have a characterising flavour and 6 commercially available products not expected to have a characterising flavour with 5 reference products (natural tobacco leaves and research cigarettes containing no flavour additives). The flavour components naturally present in the reference products were excluded from components present in commercially available products containing flavour additives. A description of the remaining flavour additives was used for categorisation. Results GC-MS measurements of the 33 tobacco products resulted in an overview of 186 chemical compounds. Of these, 144 were solely present in commercially available products. These 144 flavour additives were described using 62 different flavour descriptors extracted from flavour databases, which were categorised into eight groups largely based on the definition of characterising flavours from the European Tobacco Product Directive: fruit, spice, herb, alcohol, menthol, sweet, floral and miscellaneous. Conclusions We developed a method to identify and describe flavour additives in tobacco products. Flavour additives consist of single flavour compounds or mixtures of multiple flavour compounds, and different combinations of flavour compounds can cause a certain flavour. A flavour library helps to detect flavour additives that are characteristic for a certain flavour, and thus can be useful for regulation of flavours in tobacco and related products. PMID:28190004

Bioremediation of soil heavily contaminated with crude oil and its products: composition of the microbial consortium

Directory of Open Access Journals (Sweden)

JELENA S. MILIĆ

2009-04-01

Full Text Available Bioremediation, a process that utilizes the capability of microorganism to degrade toxic waste, is emerging as a promising technology for the treatment of soil and groundwater contamination. The technology is very effective in dealing with petroleum hydrocarbon contamination. The aim of this study was to examine the composition of the microbial consortium during the ex situ experiment of bioremediation of soil heavily contaminated with crude oil and its products from the Oil Refinery Pančevo, Serbia. After a 5.5-month experiment with biostimulation and bioventilation, the concentration of the total petroleum hydrocarbons (TPH had been reduced from 29.80 to 3.29 g/kg (89 %. In soil, the dominant microorganism population comprised Gram-positive bacteria from actinomycete-Nocardia group. The microorganisms which decompose hydrocarbons were the dominant microbial population at the end of the process, with a share of more than 80 % (range 107 CFU/g. On the basis of the results, it was concluded that a stable microbial community had been formed after initial fluctuations.

Improving Lowland Rice (O. sativa L. cv. MR219 Plant Growth Variables, Nutrients Uptake, and Nutrients Recovery Using Crude Humic Substances

Directory of Open Access Journals (Sweden)

Perumal Palanivell

2015-01-01

Full Text Available High cation exchange capacity and organic matter content of crude humic substances from compost could be exploited to reduce ammonia loss from urea and to as well improve rice growth and soil chemical properties for efficient nutrients utilization in lowland rice cultivation. Close-dynamic air flow system was used to determine the effects of crude humic substances on ammonia volatilization. A pot experiment was conducted to determine the effects of crude humic substances on rice plant growth, nutrients uptake, nutrients recovery, and soil chemical properties using an acid soil mixed with three rates of crude humic substances (20, 40, and 60 g pot−1. Standard procedures were used to evaluate rice plant dry matter production, nutrients uptake, nutrients recovery, and soil chemical properties. Application of crude humic substances increased ammonia volatilization. However, the lowest rate of crude humic substances (20 g pot−1 significantly improved total dry matter, nutrients uptake, nutrients recovery, and soil nutrients availability compared with crude humic substances (40 and 60 g pot−1 and the normal fertilization. Apart from improving growth of rice plants, crude humic substances can be used to ameliorate acid soils in rice cultivation. The findings of this study are being validated in our ongoing field trials.

Improving Lowland Rice (O. sativa L. cv. MR219) Plant Growth Variables, Nutrients Uptake, and Nutrients Recovery Using Crude Humic Substances.

Science.gov (United States)

Palanivell, Perumal; Ahmed, Osumanu Haruna; Ab Majid, Nik Muhamad; Jalloh, Mohamadu Boyie; Susilawati, Kasim

2015-01-01

High cation exchange capacity and organic matter content of crude humic substances from compost could be exploited to reduce ammonia loss from urea and to as well improve rice growth and soil chemical properties for efficient nutrients utilization in lowland rice cultivation. Close-dynamic air flow system was used to determine the effects of crude humic substances on ammonia volatilization. A pot experiment was conducted to determine the effects of crude humic substances on rice plant growth, nutrients uptake, nutrients recovery, and soil chemical properties using an acid soil mixed with three rates of crude humic substances (20, 40, and 60 g pot(-1)). Standard procedures were used to evaluate rice plant dry matter production, nutrients uptake, nutrients recovery, and soil chemical properties. Application of crude humic substances increased ammonia volatilization. However, the lowest rate of crude humic substances (20 g pot(-1)) significantly improved total dry matter, nutrients uptake, nutrients recovery, and soil nutrients availability compared with crude humic substances (40 and 60 g pot(-1)) and the normal fertilization. Apart from improving growth of rice plants, crude humic substances can be used to ameliorate acid soils in rice cultivation. The findings of this study are being validated in our ongoing field trials.

Application of Biosurfactants Produced by Pseudomonas putida using Crude Palm Oil (CPO) as Substrate for Crude Oil Recovery using Batch Method

Science.gov (United States)

Suryanti, V.; Handayani, D. S.; Masykur, A.; Septyaningsih, I.

2018-03-01

The application of biosurfactants which have been produced by Pseudomonas putida in nutrient broth medium supplemented with NaCl and crude palm oil (CPO) for oil recovery has been evaluated. The crude and purified biosurfactants have been examined for oil recovery from a laboratory oil-contaminated sand in agitated flask (batch method). Two synthetic surfactants and water as control was also performed for oil recovery as comparisons. Using batch method, the results showed that removing ability of crude oil from the oil-contaminated sand by purified and crude biosurfactants were 79.40±3.10 and 46.84±2.23 %, respectively. On other hand, the recoveries obtained with the SDS, Triton X-100 and water were 94.33±0.47, 74.84±7.39 and 34.42±1.21%respectively.

Homogeneous and Stratified Liquid-Liquid Flow Effect of a Viscosity Reducer: I. Comparison in parallel plates for heavy crude

Directory of Open Access Journals (Sweden)