USING POWDERED ACTIVATED CARBON: A CRITICAL REVIEW

Science.gov (United States)

Because the performance of powdered activated carbon (PAC) for uses other than taste and odor control is poorly documented, the purpose of this article is to critically review uses that have been reported (i.e., pesticides and herbicides, synthetic organic chemicals, and trihalom...

Treatment of coke-oven wastewater with the powdered activated carbon-contact stabilization activated sludge process. Final report

Energy Technology Data Exchange (ETDEWEB)

Suidan, M.T.; Deady, M.A.; Gee, C.S.

1983-11-01

The objective of the study was to determine optimum parameters for the operation of an innovative process train used in the treatment of coke-over wastewater. The treatment process train consisted of a contact-stabilization activated sludge system with powdered activated carbon (PAC) addition, followed by activated sludge nitrification, followed by denitrification in an anoxic filter. The control and operating parameters evaluated during the study were: (a) the average mixed-liquor PAC concentration maintained in the contact-stabilization system, (b) the solids retention time practiced in the contact-stabilization system, and (c) the hydraulic detention time maintained in the contact aeration tank. Three identical treatement process trains were constructed and employed in this study. The coke-oven wastewater used for this investigation was fed to the treatment units at 30% strength. The first part of the study was devoted to determining the interactions between the mixed liquor PAC concentration and the solids retention time in the contact-stabilization tanks. Results showed that optimum overall system performance is attainable when the highest sludge age (30 day) and highest mixed liquor PAC concentration were practiced. During the second phase of the study, all three systems were operated at a 30 day solids retention time while different detention times of 1, 2/3 and 1/3 day were evaluated in the contact tank. PAC addition rates were maintained at the former levels and, consequently, reduced contact times entailed higher mixed liquor carbon concentrations. Once again, the system receiving the highest PAC addition rate of PAC exhibited the best overall performance. This system exhibited no deterioration in process performance as a result of decreased contact detention time. 72 references, 41 figures, 24 tables.

Influence of the activated carbon nature and the aqueous matrix in the pesticides adsorption; Influencia de la naturaleza del carbon activo y la matriz acuosa en la adsorcion de plaguicidas

Energy Technology Data Exchange (ETDEWEB)

Miguel, N.; Ormad, M. P.; Lanao, M.; Mosteo, R.; Ovelleiro, J. L.

2008-07-01

The aim of this research work is to study the effectiveness of the activated carbon adsorption to remove 44 organic pesticides controlled systematically in waters of the Ebro river basin. The treatment is carried out with solutions of 5000 ng L{sup -}1 of pesticides using powered activated carbon (PAC) which origin is mineral or vegetal. Pesticides removal percentages around 25-45% are achieved using 10 mg L{sup -}1 of PAC and with a residence time of 10 minutes. In general, the adsorption capacity of the vegetal PAC is higher than of the mineral one when experiments are carried out with pesticides dissolved in distilled water. However, the presence of organic matter in natural water decreases the adsorption power of the vegetal PAC, being the behaviour of both PAC similar. (Author) 11 refs.

Improving the performance of membrane bioreactors by powdered activated carbon dosing with cost considerations.

Science.gov (United States)

Yang, W; Paetkau, M; Cicek, N

2010-01-01

Effects of powdered activated carbon (PAC) dosing on the overall performance of membrane bioreactors (MBR) were investigated in two bench-scale submerged MBRs. Positive impacts of PAC dosing on membrane fouling and the removal of 17beta-estradiol (E2) and 17alpha-ethyinylestradiol (EE2) were demonstrated over a six-month stable operational period. PAC dosing in the MBR increased the removal rates of E2 and EE2 by 3.4% and 15.8%, respectively. The average soluble extracellular polymeric substances (EPS) and colloidal total organic carbon (TOC) concentrations in the PAC-MBR sludge was 60.1% and 61.8% lower than the control MBR sludge, respectively. Lower soluble EPS and colloidal TOC concentrations in the PAC-MBR sludge resulted in a slower rate of trans-membrane pressure (TMP) increase during MBRs operation, which could prolong the lifespan of membranes. Cost assessment showed that PAC dosing could reduce the operating cost for membrane cleaning and/or membrane replacement by about 25%. The operating cost for PAC dosing could be offset by the benefit from its reducing the cost for membrane maintenance.

Redox poly[Ni(saldMp)] modified activated carbon electrode in electrochemical supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Gao Fei [Department of Physical Chemistry, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China); Li Jianling, E-mail: lijianling@ustb.edu.c [Department of Physical Chemistry, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China); Zhang Yakun; Wang Xindong [Department of Physical Chemistry, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083 (China); Kang Feiyu [Department of Material Science and Engineering, Tsinghua University, Beijing 100083 (China)

2010-08-01

The complex (2,2-dimethyl-1,3-propanediaminebis(salicylideneaminato))-nickel(II), [Ni(saldMp)], was oxidatively electropolymerized on activated carbon (AC) electrode in acetonitrile solution. The poly[Ni(saldMp)] presented an incomplete coated film on the surface of carbon particles of AC electrode by field emission scanning electron microscopy. The electrochemical behaviors of poly[Ni(saldMp)] modified activated carbon (PAC) electrode were evaluated in different potential ranges by cyclic voltammetry. Counterions and solvent swelling mainly occurred up to 0.6 V for PAC electrode by the comparison of D{sup 1/2}C values calculated from chronoamperometry experiments. Both the Ohmic resistance and Faraday resistance of PAC electrode gradually approached to those of AC electrode when its potential was ranging from 1.2 V to 0.0 V. Galvanostatic charge/discharge experiments indicated that both the specific capacitance and energy density were effectively improved by the reversible redox reaction of poly[Ni(saldMp)] film under the high current density up to 10 mA cm{sup -2} for AC electrode. The specific capacitance of PAC electrode decreased during the first 50 cycles but thereafter it remained constant for the next 200 cycles. This study showed the redox polymer may be an attractive material in supercapacitors.

Immobilized acclimated biomass-powdered activated carbon for the bioregeneration of granular activated carbon loaded with phenol and o-cresol.

Science.gov (United States)

Toh, Run-Hong; Lim, Poh-Eng; Seng, Chye-Eng; Adnan, Rohana

2013-09-01

The objectives of the study are to use immobilized acclimated biomass and immobilized biomass-powdered activated carbon (PAC) as a novel approach in the bioregeneration of granular activated carbon (GAC) loaded with phenol and o-cresol, respectively, and to compare the efficiency and rate of the bioregeneration of the phenolic compound-loaded GAC using immobilized and suspended biomasses under varying GAC dosages. Bioregeneration of GAC loaded with phenol and o-cresol, respectively, was conducted in batch system using the sequential adsorption and biodegradation approach. The results showed that the bioregeneration efficiency of GAC loaded with phenol or o-cresol was basically the same irrespective of whether the immobilized or suspended biomass was used. Nonetheless, the duration for bioregeneration was longer under immobilized biomass. The beneficial effect of immobilized PAC-biomass for bioregeneration is the enhancement of the removal rate of the phenolic compounds via adsorption and the shortening of the bioregeneration duration. Copyright © 2013 Elsevier Ltd. All rights reserved.

Altered Circadian Food Anticipatory Activity Rhythms in PACAP Receptor 1 (PAC1 Deficient Mice.

Directory of Open Access Journals (Sweden)

Jens Hannibal

Full Text Available Light signals from intrinsically photosensitive retinal ganglion cells (ipRGCs entrain the circadian clock and regulate negative masking. Two neurotransmitters, glutamate and Pituitary Adenylate Cyclase Activating Polypeptide (PACAP, found in the ipRGCs transmit light signals to the brain via glutamate receptors and the specific PACAP type 1 (PAC1 receptor. Light entrainment occurs during the twilight zones and has little effect on clock phase during daytime. When nocturnal animals have access to food only for a few hours during the resting phase at daytime, they adapt behavior to the restricted feeding (RF paradigm and show food anticipatory activity (FAA. A recent study in mice and rats demonstrating that light regulates FAA prompted us to investigate the role of PACAP/PAC1 signaling in the light mediated regulation of FAA. PAC1 receptor knock out (PAC1-/- and wild type (PAC1+/+ mice placed in running wheels were examined in a full photoperiod (FPP of 12:12 h light/dark (LD and a skeleton photoperiod (SPP 1:11:1:11 h L:DD:L:DD at 300 and 10 lux light intensity. Both PAC1-/- mice and PAC1+/+ littermates entrained to FPP and SPP at both light intensities. However, when placed in RF with access to food for 4-5 h during the subjective day, a significant change in behavior was observed in PAC1-/- mice compared to PAC1+/+ mice. While PAC1-/- mice showed similar FAA as PAC1+/+ animals in FPP at 300 lux, PAC1-/- mice demonstrated an advanced onset of FAA with a nearly 3-fold increase in amplitude compared to PAC1+/+ mice when placed in SPP at 300 lux. The same pattern of FAA was observed at 10 lux during both FPP and SPP. The present study indicates a role of PACAP/PAC1 signaling during light regulated FAA. Most likely, PACAP found in ipRGCs mediating non-image forming light information to the brain is involved.

Effect of PAC addition on immersed ultrafiltration for the treatment of algal-rich water

Energy Technology Data Exchange (ETDEWEB)

Zhang Yan, E-mail: zhang.yan113@163.com [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, 73 Huanghe Road, Nangang District, Harbin 150090 (China); Tian Jiayu; Nan Jun; Gao Shanshan; Liang Heng; Wang Meilian; Li Guibai [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, 73 Huanghe Road, Nangang District, Harbin 150090 (China)

2011-02-28

The aim of this study was to evaluate the effect of powdered activated carbon (PAC) addition on the treatment of algal-rich water by immersed ultrafiltration (UF), in terms of permeate quality and membrane fouling. Experiments were performed with a hollow-fiber polyvinyl chloride ultrafiltration membrane at a laboratory scale, 20-25 deg, C and 10 L/(m{sup 2} h) constant permeate flux. UF could achieve an absolute removal of Microcystis aeruginosa cells, but a poor removal of algogenic organic matter (AOM) released into water, contaminants responsible for severe membrane fouling. The addition of 4 g/L PAC to the immersed UF reactor significantly alleviated the development of trans-membrane pressure and enhanced the removal of dissovled organic carbon (by 10.9 {+-} 1.7%), UV{sub 254} (by 27.1 {+-} 1.7%), and microcystins (expressed as MC-LR{sub eq}, by 40.8 {+-} 4.2%). However, PAC had little effect on the rejection of hydrophilic high molecular weight AOM such as carbohydrates and proteins. It was also identified that PAC reduced the concentrations of carbohydrates and proteins in the reactor due to decreased light intensity, as well as the MC-LR{sub eq} concentration by PAC adsorption.

Impact of Increased Thermokarst Activity on Polycyclic Aromatic Compound (PAC) Accumulation in Sediment of Lakes in the Hydrocarbon-Rich Uplands Adjacent to the Mackenzie Delta, NT, Canada

Science.gov (United States)

Eickmeyer, D.; Thienpont, J. R.; Blais, J. M.

2017-12-01

In ecologically sensitive, hydrocarbon-rich regions like the western Canadian Arctic, environmental monitoring of oil and gas development often focuses on both direct and unintentional consequences of increased exploration and extraction of hydrocarbon resources. However, proper assessments of impact from these activities could be confounded by natural petrogenic sources in permafrost-rich regions where increased thermokarst activity results in permafrost exposure and erosion of hydrocarbon-rich deposits. Using a paired-lake design in the tundra uplands adjacent to the Mackenzie Delta, NT, we examined 4 lakes with retrogressive thaw slump scars along their shores, and 4 nearby undisturbed reference lakes, focusing on polycyclic aromatic compound (PAC) deposition and composition in the sediment. Total organic carbon (TOC)-normalized concentrations for parent and alkylated PACs were higher in surface sediments of slump-affected lakes than the reference lakes. This followed the pattern previously observed for persistent organic pollutants in these lakes where presence of thaw slumps on the lake shore was associated with lower TOC content in the water column, resulting in a smaller pool of available organic carbon, leading to higher PAC concentrations. Diagnostic ratios of specific PACs also suggested the sediment of slump-affected lakes had greater influence from petroleum-based PAC sources than their reference counterparts. This interpretation was corroborated by a principle components analysis of the metal content in the sediment. Slump-affected lakes were enriched in metals related to shale-based, Quaternary deposits of the Mackenzie Basin (e.g. Ca, Sr, Mg) when compared to reference lakes where these surficial materials were not exposed by thermokarst activity. Higher PAC concentrations and composition indicative of petrogenic sources observed in sediment of slump-affected lakes were best explained as a combination of low TOC availability and increased inputs of

The influence of iron oxide nanoparticles upon the adsorption of organic matter on magnetic powdered activated carbon.

Science.gov (United States)

Lompe, Kim Maren; Menard, David; Barbeau, Benoit

2017-10-15

Combining powdered activated carbon (PAC) with magnetic iron oxides has been proposed in the past to produce adsorbents for natural organic matter (NOM) removal that can be easily separated using a magnetic field. However, the trade-off between the iron oxides' benefits and the reduced carbon content, porosity, and surface area has not yet been investigated systematically. We produced 3 magnetic powdered activated carbons (MPAC) with mass fractions of 10%, 38% and 54% maghemite nanoparticles and compared them to bare PAC and pure nanoparticles with respect to NOM adsorption kinetics and isotherms. While adsorption kinetics were not influenced by the presence of the iron oxide nanoparticles (IONP), as shown by calculated diffusion coefficients from the homogeneous surface diffusion model, nanoparticles reduced the adsorption capacity of NOM due to their lower adsorption capacity. Although the nanoparticles added mesoporosity to the composite materials they blocked intrinsic PAC mesopores at mass fractions >38% as measured by N 2 -adsorption isotherms. Below this mass fraction, the adsorption capacity was mainly dependent on the carbon content in MPAC and mesopore blocking was negligible. If NOM adsorption with MPAC is desired, a highly mesoporous PAC and a low IONP mass fraction should be chosen during MPAC synthesis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Impact of salinity and dispersed oil on adsorption of dissolved aromatic hydrocarbons by activated carbon and organoclay

Energy Technology Data Exchange (ETDEWEB)

Younker, Jessica M.; Walsh, Margaret E., E-mail: mwalsh2@dal.ca

2015-12-15

Highlights: • Powdered activated carbon (PAC) outperformed organoclay for dissolved aromatics removal • Dispersed oil reduced the adsorption capacity of PAC but not organoclay • Salinity did not affect phenol or naphthalene removal by PAC or BTMA-organoclay • Commercial organoclay had reduced adsorption capacity in saline water due to aggregation • PAC performed better in single solute systems than multi-solute systems - Abstract: Adsorption capacity of phenol and naphthalene by powdered activated carbon (PAC), a commercial organoclay (OC) and a lab synthesized organoclay (BTMA) was studied using batch adsorption experiments under variable feed water quality conditions including single- and multi- solute conditions, fresh water, saline water and oily-and-saline water. Increasing salinity levels was found to reduce adsorption capacity of OC, likely due to destabilization, aggregation and subsequent removal of organoclay from the water column, but did not negatively impact adsorption capacity of PAC or BTMA. Increased dispersed oil concentrations were found to reduce the surface area of all adsorbents. This decreased the adsorption capacity of PAC for both phenol and naphthalene, and reduced BTMA adsorption of phenol, but did not negatively affect naphthalene removals by either organoclay. The presence of naphthalene as a co-solute significantly reduced phenol adsorption by PAC, but had no impact on organoclay adsorption. These results indicated that adsorption by PAC occurred via a surface adsorption mechanism, while organoclay adsorption occurred by hydrophobic or pi electron interactions. In general, PAC was more sensitive to changes in water quality than either of the organoclays evaluated in this study. However, PAC exhibited a higher adsorption capacity for phenol and naphthalene compared to both organoclays even in adverse water quality conditions.

Impact of salinity and dispersed oil on adsorption of dissolved aromatic hydrocarbons by activated carbon and organoclay

International Nuclear Information System (INIS)

Younker, Jessica M.; Walsh, Margaret E.

2015-01-01

Highlights: • Powdered activated carbon (PAC) outperformed organoclay for dissolved aromatics removal • Dispersed oil reduced the adsorption capacity of PAC but not organoclay • Salinity did not affect phenol or naphthalene removal by PAC or BTMA-organoclay • Commercial organoclay had reduced adsorption capacity in saline water due to aggregation • PAC performed better in single solute systems than multi-solute systems - Abstract: Adsorption capacity of phenol and naphthalene by powdered activated carbon (PAC), a commercial organoclay (OC) and a lab synthesized organoclay (BTMA) was studied using batch adsorption experiments under variable feed water quality conditions including single- and multi- solute conditions, fresh water, saline water and oily-and-saline water. Increasing salinity levels was found to reduce adsorption capacity of OC, likely due to destabilization, aggregation and subsequent removal of organoclay from the water column, but did not negatively impact adsorption capacity of PAC or BTMA. Increased dispersed oil concentrations were found to reduce the surface area of all adsorbents. This decreased the adsorption capacity of PAC for both phenol and naphthalene, and reduced BTMA adsorption of phenol, but did not negatively affect naphthalene removals by either organoclay. The presence of naphthalene as a co-solute significantly reduced phenol adsorption by PAC, but had no impact on organoclay adsorption. These results indicated that adsorption by PAC occurred via a surface adsorption mechanism, while organoclay adsorption occurred by hydrophobic or pi electron interactions. In general, PAC was more sensitive to changes in water quality than either of the organoclays evaluated in this study. However, PAC exhibited a higher adsorption capacity for phenol and naphthalene compared to both organoclays even in adverse water quality conditions.

Granular activated carbon for removal of organic matter and turbidity from secondary wastewater.

Science.gov (United States)

Hatt, J W; Germain, E; Judd, S J

2013-01-01

A range of commercial granular activated carbon (GAC) media have been assessed as pretreatment technologies for a downstream microfiltration (MF) process. Media were assessed on the basis of reduction in both organic matter and turbidity, since these are known to cause fouling in MF membranes. Isotherm adsorption analysis through jar testing with supplementary column trials revealed a wide variation between the different adsorbent materials with regard to organics removal and adsorption kinetics. Comparison with previous work using powdered activated carbon (PAC) revealed that for organic removal above 60% the use of GAC media incurs a significantly lower carbon usage rate than PAC. All GACs tested achieved a minimum of 80% turbidity removal. This combination of turbidity and organic removal suggests that GAC would be expected to provide a significant reduction in fouling of a downstream MF process with improved product water quality.

Quantification of arsenic in activated carbon using particle induced X-ray emission

International Nuclear Information System (INIS)

Yadav, Nirbhay N.; Maheswaran, Saravanamuthu; Shutthanandan, Vaithiyalingam; Thevuthasan, Suntharampillai; Ngo, Huu H.; Vigneswaran, Saravanamuth

2006-01-01

To date, the trace elemental analysis of solids with inhomogeneous internal structure has been limited, particularly in the case of adsorbents. High-energy ion beam based particle induced X-ray emission (PIXE) is an ideal analytical tool suitable for simultaneous quantification of trace elements with high accuracy. In this study, PIXE was used to quantify arsenic in the adsorbents, granular activated carbon (GAC) and powder activated carbon (PAC). Pelletized and unmodified GAC and PAC samples were analyzed along with powder samples deposited on thin teflon filters. These sample preparation methods resulted in samples of various thicknesses and densities. PIXE measurements taken from these samples were compared to results from neutron activation analysis (NAA) and atomic absorption spectroscopy (AAS). There is a good agreement between the values from the NAA and pelletized PIXE measurements and some AAS measurements

Removal of a synthetic organic chemical by PAC-UF systems. II: Model application.

Science.gov (United States)

Matsui, Y; Colas, F; Yuasa, A

2001-02-01

This paper describes several application potentials with a recently developed model for predicting the synthetic organic chemical (SOC) removal by powdered activated carbon (PAC) adsorption during ultrafiltration (UF) and discusses the removal mechanism. The model was successfully applied, without any modification, to dead-end mode operation as well as to cross-flow mode operation, validating the assumption of the internal diffusion control mechanism and the continuously-stirred-tank-reactor (CSTR) concept. Even when UF was operated in a cross-flow mode, PAC added was re-circulating in suspension for only a short time. Then, solute uptake took place mostly by PAC immobilized in membrane tubes not only for dead-end operation but also for cross-flow operation. Therefore, cross-flow operation did not have any advantage regarding the SOC mass transfer on PAC in UF loop over dead-end operation. The model simulation implied that pulse PAC addition at the beginning of filtration cycle resulted better SOC removal than continuous PAC addition. However, for the pulse PAC addition mode, the model predicted somewhat lower effluent SOC concentration than the observed values, and the benefit of pulse PAC application in terms of reducing SOC over its continuous dosage was not confirmed. Longer detention time of PAC dosed in a pulse than continuously dosed PAC could possibly further decrease internal diffusivity.

Performance of Submerged Membrane Bioreactor Combined with Powdered Activated Carbon Addition for the Treatment of an Industrial Wastewater

Directory of Open Access Journals (Sweden)

Tri Widjaja

2010-02-01

Full Text Available Membrane technology is one of the alternative solutions to overcome industrial wastewater treatment developed nowadays. The addition of PAC (Powdered Activated Carbon in the activated sludge using Submerged Membrane Adsorption Hybrid Bioreactor (SMAHBR is expected to increase the organic material removal. The purpose of this study was to determine the performance of submerged membrane bioreactor and activated carbon adsorption capacity of organic materials in wastewater. This study used SIER (Surabaya Industrial Estate Rungkut – Surabaya, Indonesia waste as activated sludge operated at Mixed Liquor Suspended Solid (MLSS concentrations of 8000 and 15000 mg/l, and Chemical Oxygen Demand (COD concentrations of 1500, 2500 mg/l, Sludge Retention Time (SRT of 10;20; and 30 days and activated carbon variables of 0%; 2.5%; 5%; 7.5%; 10%. The results showed that the fouling potential occurred at high MLSS where the COD removal occurred at PAC addition of 10% reaching 91.86%. High Soluble Microbial Product (SMP accumulation (± 10 mg/l occurred in short SRT and high MLSS concentration. PAC addition resulted in decreased microorganisms in the reactor and better effluent of SMAHBR, as a result, the performance of the submerged membrane bioreactor would be restored.

Adsorption of selected emerging contaminants onto PAC and GAC: Equilibrium isotherms, kinetics, and effect of the water matrix.

Science.gov (United States)

Real, Francisco J; Benitez, F Javier; Acero, Juan L; Casas, Francisco

2017-07-03

The removal of three emerging contaminants (ECs) (amitriptyline hydrochloride (AH), methyl salicylate (MS) and 2-phenoxyethanol (PE)) dissolved in several water matrices by means of their adsorption onto powdered activated carbon (PAC) and granular activated carbon (GAC) has been investigated. When dissolved in ultrapure water, adsorption of the ECs followed the trend of AH > MS > PE, with a positive effect of the adsorbent dose. According to the analysis of the adsorption isotherms and adsorption kinetics, PAC showed strongly higher adsorption efficiency in both capacity and velocity of the adsorption, in agreement with its higher mesoporosity. Equilibrium isotherm data were fitted by Langmuir and Freundlich models. Pseudo-second order kinetics modeled very successfully the adsorption process. Finally, the effect of the presence of dissolved organic matter (DOM) in the water matrices (ultrapure water, surface water and two effluents from wastewater treatment plants) on the adsorption of the selected ECs onto PAC was established, as well as its performance on the removal of water quality parameters. Results show a negative effect of the DOM content on the adsorption efficiency. Over 50% of organic matter was removed with high PAC doses, revealing that adsorption onto PAC is an effective technology to remove both micro-pollutants and DOM from water matrices.

Treatment of micropollutants in municipal wastewater: Ozone or powdered activated carbon?

International Nuclear Information System (INIS)

Margot, Jonas; Kienle, Cornelia; Magnet, Anoÿs; Weil, Mirco; Rossi, Luca; Alencastro, Luiz Felippe de; Abegglen, Christian; Thonney, Denis; Chèvre, Nathalie; Schärer, Michael

2013-01-01

Many organic micropollutants present in wastewater, such as pharmaceuticals and pesticides, are poorly removed in conventional wastewater treatment plants (WWTPs). To reduce the release of these substances into the aquatic environment, advanced wastewater treatments are necessary. In this context, two large-scale pilot advanced treatments were tested in parallel over more than one year at the municipal WWTP of Lausanne, Switzerland. The treatments were: i) oxidation by ozone followed by sand filtration (SF) and ii) powdered activated carbon (PAC) adsorption followed by either ultrafiltration (UF) or sand filtration. More than 70 potentially problematic substances (pharmaceuticals, pesticides, endocrine disruptors, drug metabolites and other common chemicals) were regularly measured at different stages of treatment. Additionally, several ecotoxicological tests such as the Yeast Estrogen Screen, a combined algae bioassay and a fish early life stage test were performed to evaluate effluent toxicity. Both treatments significantly improved the effluent quality. Micropollutants were removed on average over 80% compared with raw wastewater, with an average ozone dose of 5.7 mg O 3 l −1 or a PAC dose between 10 and 20 mg l −1 . Depending on the chemical properties of the substances (presence of electron-rich moieties, charge and hydrophobicity), either ozone or PAC performed better. Both advanced treatments led to a clear reduction in toxicity of the effluents, with PAC-UF performing slightly better overall. As both treatments had, on average, relatively similar efficiency, further criteria relevant to their implementation were considered, including local constraints (e.g., safety, sludge disposal, disinfection), operational feasibility and cost. For sensitive receiving waters (drinking water resources or recreational waters), the PAC-UF treatment, despite its current higher cost, was considered to be the most suitable option, enabling good removal of most

p-Nitrophenol removal by combination of powdered activated carbon adsorption and ultrafiltration - comparison of different operational modes.

Science.gov (United States)

Ivancev-Tumbas, Ivana; Hobby, Ralph; Küchle, Benjamin; Panglisch, Stefan; Gimbel, Rolf

2008-09-01

Ultrafiltration is classified as a low-pressure membrane technology which effectively removes particulate matter and microorganisms and to a certain extent dissolved organic matter (15-25%) and colour. The technology has been optimized and is becoming competitive compared to conventional processes for larger scale plant capacities. In combination with activated carbon it is an effective barrier regarding the removal of synthetic organic chemicals. Growing interest in ultrafiltration raises the question of better usage of the adsorption capacity of powdered activated carbon (PAC) used in combination with this low-pressure membrane technique. This paper presents a pilot plant study of different PAC dosing procedures within a combined hybrid membrane IN/OUT process for removal of p-nitrophenol (PNP) from water (c(0)=1mg/L) under real case conditions (e.g. usage of the same module for the whole duration of the experiment, backwashing with permeate water, no separate saturation of the membrane with substance without presence of carbon). p-Nitrophenol was chosen as an appropriate test substance to assess the efficiency of different operation modes. Dead-end and cross-flow filtration were compared with respect to different PAC dosing procedures: continuous dosing into a continuously stirred tank reactor (CSTR) in front of the module and direct dosing into the pipe in front of the module (continuous, single-pulse and multi-pulse dosing). There was no advantage in cross-flow mode over dead-end referring to PNP concentration in the permeate. Relating to the carbon dosing procedure, the best results were obtained for continuous PAC addition. The option of dosing directly into the pipe has the advantage of no additional tank being necessary. In the case of single-pulse dosing, the formation of a carbon layer on the membrane surface was assumed and an LDF model applied for a simplified estimation of the "breakthrough behaviour" in the thus formed "PAC filter layer".

Removal of micropollutants with coarse-ground activated carbon for enhanced separation with hydrocyclone classifiers.

Science.gov (United States)

Otto, N; Platz, S; Fink, T; Wutscherk, M; Menzel, U

2016-01-01

One key technology to eliminate organic micropollutants (OMP) from wastewater effluent is adsorption using powdered activated carbon (PAC). To avoid a discharge of highly loaded PAC particles into natural water bodies a separation stage has to be implemented. Commonly large settling tanks and flocculation filters with the application of coagulants and flocculation aids are used. In this study, a multi-hydrocyclone classifier with a downstream cloth filter has been investigated on a pilot plant as a space-saving alternative with no need for a dosing of chemical additives. To improve the separation, a coarser ground PAC type was compared to a standard PAC type with regard to elimination results of OMP as well as separation performance. With a PAC dosing rate of 20 mg/l an average of 64.7 wt% of the standard PAC and 79.5 wt% of the coarse-ground PAC could be separated in the hydrocyclone classifier. A total average separation efficiency of 93-97 wt% could be reached with a combination of both hydrocyclone classifier and cloth filter. Nonetheless, the OMP elimination of the coarse-ground PAC was not sufficient enough to compete with the standard PAC. Further research and development is necessary to find applicable coarse-grained PAC types with adequate OMP elimination capabilities.

Removal of phenol by powdered activated carbon prepared from coal gasification tar residue.

Science.gov (United States)

Wang, Xiong-Lei; Shen, Jun; Niu, Yan-Xia; Wang, Yu-Gao; Liu, Gang; Sheng, Qing-Tao

2018-03-01

Coal gasification tar residue (CGTR) is a kind of environmentally hazardous byproduct generated in fixed-bed coal gasification process. The CGTR extracted by ethyl acetate was used to prepare powdered activated carbon (PAC), which is applied later for adsorption of phenol. The results showed that the PAC prepared under optimum conditions had enormous mesoporous structure, and the iodine number reached 2030.11 mg/g, with a specific surface area of 1981 m 2 /g and a total pore volume of 0.92 ml/g. Especially, without loading other substances, the PAC, having a strong magnetism, can be easily separated after it adsorbs phenol. The adsorption of phenol by PAC was studied as functions of contact time, temperature, PAC dosage, solution concentration and pH. The results showed a fast adsorption speed and a high adsorption capacity of PAC. The adsorption process was exothermic and conformed to the Freundlich models. The adsorption kinetics fitted better to the pseudo-second-order model. These results show that CGTR can be used as a potential adsorbent of phenols in wastewater.

Impact of PAC Fines in Fouling of Polymeric and Ceramic Low-Pressure Membranes for Drinking Water Treatment

Science.gov (United States)

Oligny, Laurent; Bérubé, Pierre R.; Barbeau, Benoit

2016-01-01

This study assessed the issue of membrane fouling in a Hybrid Membrane Process (HMP) due to the export of powdered activated carbon (PAC) fines from a pretreatment contactor. Two parallel pilot-scale ceramic and polymeric membranes were studied. Reversible and irreversible foulings were measured following three cleaning procedures: Physical backwashing (BW), chemically enhanced backwashing (CEB) and Clean-in-Place (CIP). The impacts on fouling of membrane type, operation flux increase and the presence/absence of the PAC pretreatment were investigated. Membranes without pretreatment were operated in parallel as a control. In addition, CIP washwaters samples were analyzed to measure organic and inorganic foulants removed from the membranes. It was observed that for the polymeric membranes, fouling generally increased with the presence of the PAC pretreatment because of the export of fines. On the contrary, the ceramic membranes were not significantly impacted by their presence. The analysis of CIP washwaters showed a greater total organic carbon (TOC) content on membranes with a PAC pretreatment while no similar conclusion could be made for inorganic foulants. PMID:27399788

Impact of PAC Fines in Fouling of Polymeric and Ceramic Low-Pressure Membranes for Drinking Water Treatment.

Science.gov (United States)

Oligny, Laurent; Bérubé, Pierre R; Barbeau, Benoit

2016-07-07

This study assessed the issue of membrane fouling in a Hybrid Membrane Process (HMP) due to the export of powdered activated carbon (PAC) fines from a pretreatment contactor. Two parallel pilot-scale ceramic and polymeric membranes were studied. Reversible and irreversible foulings were measured following three cleaning procedures: Physical backwashing (BW), chemically enhanced backwashing (CEB) and Clean-in-Place (CIP). The impacts on fouling of membrane type, operation flux increase and the presence/absence of the PAC pretreatment were investigated. Membranes without pretreatment were operated in parallel as a control. In addition, CIP washwaters samples were analyzed to measure organic and inorganic foulants removed from the membranes. It was observed that for the polymeric membranes, fouling generally increased with the presence of the PAC pretreatment because of the export of fines. On the contrary, the ceramic membranes were not significantly impacted by their presence. The analysis of CIP washwaters showed a greater total organic carbon (TOC) content on membranes with a PAC pretreatment while no similar conclusion could be made for inorganic foulants.

Impact of PAC Fines in Fouling of Polymeric and Ceramic Low-Pressure Membranes for Drinking Water Treatment

Directory of Open Access Journals (Sweden)

Laurent Oligny

2016-07-01

Full Text Available This study assessed the issue of membrane fouling in a Hybrid Membrane Process (HMP due to the export of powdered activated carbon (PAC fines from a pretreatment contactor. Two parallel pilot-scale ceramic and polymeric membranes were studied. Reversible and irreversible foulings were measured following three cleaning procedures: Physical backwashing (BW, chemically enhanced backwashing (CEB and Clean-in-Place (CIP. The impacts on fouling of membrane type, operation flux increase and the presence/absence of the PAC pretreatment were investigated. Membranes without pretreatment were operated in parallel as a control. In addition, CIP washwaters samples were analyzed to measure organic and inorganic foulants removed from the membranes. It was observed that for the polymeric membranes, fouling generally increased with the presence of the PAC pretreatment because of the export of fines. On the contrary, the ceramic membranes were not significantly impacted by their presence. The analysis of CIP washwaters showed a greater total organic carbon (TOC content on membranes with a PAC pretreatment while no similar conclusion could be made for inorganic foulants.

Adsorption of cadmium from aqueous solutions on sulfurized activated carbon prepared from nut shells

International Nuclear Information System (INIS)

Fouladi Tajar, Amir; Kaghazchi, Tahereh; Soleimani, Mansooreh

2009-01-01

Low-cost activated carbon, derived from nut shells, and its modified sample have been used as replacements for the current expensive methods of removing cadmium from aqueous solutions and waste waters. Adsorption of cadmium onto four kinds of activated carbons has been studied; prepared activated carbon (PAC), commercial activated carbon (CAC), and the sulfurized ones (SPAC and SCAC). The activated carbon has been derived, characterized, treated with sulfur and then utilized for the removal of Cd 2+ . Sulfurizing agent (SO 2 gas) was successfully used in adsorbents' modification process at the ambient temperature. Samples were then characterized and tested as adsorbents of cadmium. Effect of some parameters such as contact time, initial concentration and pH were examined. With increasing pH, the adsorption of cadmium ions was increased and maximum removal, 92.4% for SPAC, was observed in pH > 8.0 (C 0 = 100 mg/L). The H-type adsorption isotherms, obtained for the adsorbents, indicated a favorable process. Adsorption data on both prepared and commercial activated carbon, before and after sulfurization, followed both the Frendlich and Langmuir models. They were better fitted by Frendlich isotherm as compared to Langmuir. The maximum adsorption capacities were 90.09, 104.17, 126.58 and 142.86 mg/g for CAC, PAC, SCAC and SPAC, respectively. Accordingly, surface modification of activated carbons using SO 2 greatly enhanced cadmium removal. The reversibility of the process has been studied in a qualitative manner and it shows that the spent SPAC can be effectively regenerated for further use easily.

Quantitative detection of powdered activated carbon in wastewater treatment plant effluent by thermogravimetric analysis (TGA).

Science.gov (United States)

Krahnstöver, Therese; Plattner, Julia; Wintgens, Thomas

2016-09-15

For the elimination of potentially harmful micropollutants, powdered activated carbon (PAC) adsorption is applied in many wastewater treatment plants (WWTP). This holds the risk of PAC leakage into the WWTP effluent and desorption of contaminants into natural water bodies. In order to assess a potential PAC leakage, PAC concentrations below several mg/L have to be detected in the WWTP effluent. None of the methods that are used for water analysis today are able to differentiate between activated carbon and solid background matrix. Thus, a selective, quantitative and easily applicable method is still needed for the detection of PAC residues in wastewater. In the present study, a method was developed to quantitatively measure the PAC content in wastewater by using filtration and thermogravimetric analysis (TGA), which is a well-established technique for the distinction between different solid materials. For the sample filtration, quartz filters with a temperature stability up to 950 °C were used. This allowed for sensitive and well reproducible measurements, as the TGA was not affected by the presence of the filter. The sample's mass fractions were calculated by integrating the mass decrease rate obtained by TGA in specific, clearly identifiable peak areas. A two-step TGA heating method consisting of N2 and O2 atmospheres led to a good differentiation between PAC and biological background matrix, thanks to the reduction of peak overlapping. A linear correlation was found between a sample's PAC content and the corresponding peak areas under N2 and O2, the sample volume and the solid mass separated by filtration. Based on these findings, various wastewater samples from different WWTPs were then analyzed by TGA with regard to their PAC content. It was found that, compared to alternative techniques such as measurement of turbidity or total suspended solids, the newly developed TGA method allows for a quantitative and selective detection of PAC concentrations down to 0

Fly ash: An alternative to powdered activated carbon for the removal ...

African Journals Online (AJOL)

This paper reports the use of powdered activated carbon (PAC) and raw coal fly ash (RFA) in the removal of eosin dye from aqueous solution in batch processes. Operational parameters such as contact time, initial dye concentration, pH and temperature were investigated. Adsorption equilibrium was established in 120 min ...

The future of PACS

International Nuclear Information System (INIS)

Nagy, Paul G.

2007-01-01

How will the future of picture archiving and communication systems (PACS) look, and how will this future affect the practice of radiology? We are currently experiencing disruptive innovations that will force an architectural redesign, making the majority of today’s commercial PACS obsolete as the field matures and expands to include imaging throughout the medical enterprise. The common architecture used for PACS cannot handle the massive amounts of data being generated by even current versions of computed tomography and magnetic resonance scanners. If a PACS cannot handle today’s technology, what will happen as the field expands to encompass pathology imaging, cone-beam reconstruction, and multispectral imaging? The ability of these new technologies to enhance research and clinical care will be impaired if PACS architectures are not prepared to support them. In attempting a structured approach to predictions about the future of PACS, we offer projections about the technologies underlying PACS as well as the evolution of standards development and the changing needs of a broad range of medical imaging. Simplified models of the history of the PACS industry are mined for the assumptions they provide about future innovations and trends. The physicist frequently participates in or directs technical assessments for medical equipment, and many physicists have extended these activities to include imaging informatics. It is hoped that by applying these speculative but experienced-based predictions, the interested medical physicist will be better able to take the lead in setting information technology strategies that will help facilities not only prepare for the future but continue to enjoy the benefits of technological innovations without disruptive, expensive, and unexpected changes in architecture. A good PACS strategy can help accelerate the time required for innovations to go from the drawing board to clinical implementation.

Pilot-scale removal of pharmaceuticals in municipal wastewater: Comparison of granular and powdered activated carbon treatment at three wastewater treatment plants.

Science.gov (United States)

Kårelid, Victor; Larsson, Gen; Björlenius, Berndt

2017-05-15

Adsorption with activated carbon is widely suggested as an option for the removal of organic micropollutants including pharmaceutically active compounds (PhACs) in wastewater. In this study adsorption with granular activated carbon (GAC) and powdered activated carbon (PAC) was analyzed and compared in parallel operation at three Swedish wastewater treatment plants with the goal to achieve a 95% PhAC removal. Initially, mapping of the prevalence of over 100 substances was performed at each plant and due to low concentrations a final 22 were selected for further evaluation. These include carbamazepine, clarithromycin and diclofenac, which currently are discussed for regulation internationally. A number of commercially available activated carbon products were initially screened using effluent wastewater. Of these, a reduced set was selected based on adsorption characteristics and cost. Experiments designed with the selected carbons in pilot-scale showed that most products could indeed remove PhACs to the target level, both on total and individual basis. In a setup using internal recirculation the PAC system achieved a 95% removal applying a fresh dose of 15-20 mg/L, while carbon usage rates for the GAC application were much broader and ranged from carbon product. The performance of the PAC products generally gave better results for individual PhACs in regards to carbon availability. All carbon products showed a specific adsorption for a specific PhAC meaning that knowledge of the target pollutants must be acquired before successful design of a treatment system. In spite of different configurations and operating conditions of the different wastewater treatment plants no considerable differences regarding pharmaceutical removal were observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Upgrade of deep bed filtration with activated carbon dosage for compact micropollutant removal from wastewater in technical scale.

Science.gov (United States)

Löwenberg, Jonas; Zenker, Armin; Krahnstöver, Thérèse; Boehler, Marc; Baggenstos, Martin; Koch, Gerhard; Wintgens, Thomas

2016-05-01

The removal of micropollutants from drinking and wastewater by powdered activated carbon (PAC) adsorption has received considerable attention in research over the past decade with various separation options having been investigated. With Switzerland as the first country in the world having adopted a new legislation, which forces about 100 wastewater treatment plants to be upgraded for the removal of organic micropollutants from municipal wastewater, the topic has reached practical relevance. In this study, the process combination of powdered activated carbon (PAC) adsorption and deep bed filtration (DBF) for advanced municipal wastewater treatment was investigated over an extended period exceeding one year of operation in technical scale. The study aimed to determine optimum process conditions to achieve sufficient micropollutant removal in agreement with the new Swiss Water Ordinance under most economic process design. It was shown that the addition of PAC and Fe(3+) as combined coagulation and flocculation agent improved effluent water quality with respect to dissolved organic pollutants as well as total suspended solids (TSS), turbidity and PO4-P concentration in comparison to a DBF operated without the addition of PAC and Fe(3+). Sufficient micropollutant (MP) removal of around 80% was achieved at PAC dosages of 10 mg/L revealing that PAC retained in the filter bed maintained considerable adsorption capacity. In the investigated process combination the contact reactor serves for adsorption as well as for flocculation and allowed for small hydraulic retention times of minimum 10 min while maintaining sufficient MP removal. The flocculation of two different PAC types was shown to be fully concluded after 10-15 min, which determined the flocculation reactor size while both PAC types proved suitable for the application in combination with DBF and showed no significant differences in MP removal. Finally, the capping of PAC dosage during rain water periods, which

PACS industry in Korea

Science.gov (United States)

Kim, Hee-Joung

2002-05-01

PACS industry in Korea has been rapidly growing, since government had supported collaborative PACS project between industry and university hospital. In the beginning, PACS industry had focused on developing peripheral PACS solutions, while the Korea PACS society was being formed. A few companies had started developing and installing domestic large-scale full-PACS system for teaching hospitals. Several years later, many hospitals have installed full-PACS system with national policy of reimbursement for PACS exams in November 1999. Both experiences of full-PACS installation and national policy generated tremendous intellectual and technological expertise about PACS at all levels, clinical, hospital management, education, and industrial sectors. There are now more than 20 domestic PACS companies. They have enough experiences which are capable of installing a truly full-PACS system for large-scale teaching hospitals. As an example, a domestic company had installed more than 40 full-PACS systems within 2-3 years. Enough experiences of full-PACS installation in Korea lead PACS industry to start exporting their full-PACS solutions. However, further understanding and timely implementation of continuously evolving international standard and integrated healthcare enterprise concepts may be necessary for international leading of PACS technologies for the future.

Removal of cationic surfactant (CTAB from aqueous solution on to activated carbon obtained from corncob.

Directory of Open Access Journals (Sweden)

S. M. Yakout

2009-05-01

Full Text Available Direct and indirect releases of large quantities of surfactants to the environment may result in serious health and environmental problems. Therefore, surfactants should be removed from water before water is released to the environment or delivered for public use. Using powdered activated carbon (PAC as adsorbent may be an effective technique to remove surfactants. In this study, the removal of surfactants by PAC was investigated and the influencesof the operating parameters on the effectiveness on adsorption rate were studied. Cationic surfactant, Cetyl trimethyl ammonium bromide (CTAB was selected for the experiments. A series of batch experiments were performed to determine the sorption isotherms of surfactants to PAC. The results showed that carbon structure affect mainly on the surfactant adsorption. Surfactant equilibrium data fitted very well to the binary langmuir model. The pseudo first-,second- order and intraparticle diffusion kinetic models were applied. Both, the external mass transfer and intraparticle diffusion mechanisms involve in CTAB sorption.

Activated carbon amendment to sequester PAHs in contaminated soil: a lysimeter field trial.

Science.gov (United States)

Hale, Sarah E; Elmquist, Marie; Brändli, Rahel; Hartnik, Thomas; Jakob, Lena; Henriksen, Thomas; Werner, David; Cornelissen, Gerard

2012-04-01

Activated carbon (AC) amendment is an innovative method for the in situ remediation of contaminated soils. A field-scale AC amendment of either 2% powder or granular AC (PAC and GAC) to a PAH contaminated soil was carried out in Norway. The PAH concentration in drainage water from the field plot was measured with a direct solvent extraction and by deploying polyoxymethylene (POM) passive samplers. In addition, POM samplers were dug directly in the AC amended and unamended soil in order to monitor the reduction in free aqueous PAH concentrations in the soil pore water. The total PAH concentration in the drainage water, measured by direct solvent extraction of the water, was reduced by 14% for the PAC amendment and by 59% for GAC, 12 months after amendment. Measurements carried out with POM showed a reduction of 93% for PAC and 56% for GAC. The free aqueous PAH concentration in soil pore water was reduced 93% and 76%, 17 and 28 months after PAC amendment, compared to 84% and 69% for GAC. PAC, in contrast to GAC, was more effective for reducing freely dissolved concentrations than total dissolved ones. This could tentatively be explained by leaching of microscopic AC particles from PAC. Secondary chemical effects of the AC amendment were monitored by considering concentration changes in dissolved organic carbon (DOC) and nutrients. DOC was bound by AC, while the concentrations of nutrients (NO(3), NO(2), NH(4), PO(4), P-total, K, Ca and Mg) were variable and likely affected by external environmental factors. Copyright © 2012 Elsevier Ltd. All rights reserved.

Photocatalytic degradation of clofibric acid, carbamazepine and iomeprol using conglomerated TiO2 and activated carbon in aqueous suspension.

Science.gov (United States)

Ziegmann, Markus; Frimmel, Fritz H

2010-01-01

The combination of powdered activated carbon (PAC) and TiO(2) has been tested for synergistic/antagonistic effects in the photocatalytic degradation of carbamazepine, clofibric acid and iomeprol. Synergistic effects are thought to be caused by rapid adsorption on the PAC surface followed by diffusion to the TiO(2) surface and photocatalytic degradation. The Freundlich constant K(F) was used for comparing the sorption properties of the three substances and it was found that K(F) for clofibric acid was 3 times lower than for carbamazepine and iomeprol, regardless of the kind of PAC used. A PAC with a distinct tendency to form conglomerates was selected so that a high percentage of the PAC surface was in direct proximity to the TiO(2) surface. The photocatalytic degradation of the pharmaceutically active compounds studied followed pseudo-first order kinetics. Synergistic effects only occurred for clofibric acid (factor 1.5) and an inverse relationship between adsorption affinity and synergistic effects was found. High affinity of the target substances to the PAC surface seemed to be counterproductive for the photocatalytic degradation.

Photo-dynamics of the lyophilized photo-activated adenylate cyclase NgPAC2 from the amoeboflagellate Naegleria gruberi NEG-M strain

Energy Technology Data Exchange (ETDEWEB)

Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Fakultät für Physik, Universität Regensburg, Universitätsstrasse 31, D-93053 Regensburg (Germany); Tanwar, M.; Veetil, S.K.; Kateriya, S. [Department of Biochemistry, University of Delhi South Campus, Benito Juarez Road, New Delhi 110021 (India); Stierl, M.; Hegemann, P. [Institut für Biologie/Experimentelle Biophysik, Humboldt Universität zu Berlin, Invalidenstrasse 42, D-10115 Berlin (Germany)

2013-09-23

Highlights: • Lyophilizing of NgPAC2 from Naegleria gruberi caused loss of BLUF domain activity. • Photo-induced tyrosine to flavin electron transfer in lyophilized NgPAC2. • Photo-induced Tyr–Tyr cross-linking to o,o′-dityrosine in lyophilized NgPAC2. • Photo-induced partial flavin cofactor reduction in lyophilized NgPAC2. • Two NgPAC2 conformations with fast and slow photo-induced electron transfer. - Abstract: The absorption and emission spectroscopic behavior of lyophilized photo-activated adenylate cyclase NgPAC2 from the amoeboflagellate Naegleria gruberi NEG-M strain consisting of a BLUF domain (BLUF = Blue Light sensor Using Flavin) and a cyclase homology domain was studied in the dark, during blue-light exposure and after blue-light exposure at a temperature of 4 °C. The BLUF domain photo-cycle dynamics observed for snap-frozen NgPAC2 was lost by lyophilization (no signaling state formation with flavin absorption red-shift). Instead, blue-light photo-excitation of lyophilized NgPAC2 caused sterically restricted Tyr–Tyr cross-linking (o,o′-ditysosine formation) and partial flavin cofactor reduction.

Photo-dynamics of the lyophilized photo-activated adenylate cyclase NgPAC2 from the amoeboflagellate Naegleria gruberi NEG-M strain

International Nuclear Information System (INIS)

Penzkofer, A.; Tanwar, M.; Veetil, S.K.; Kateriya, S.; Stierl, M.; Hegemann, P.

2013-01-01

Highlights: • Lyophilizing of NgPAC2 from Naegleria gruberi caused loss of BLUF domain activity. • Photo-induced tyrosine to flavin electron transfer in lyophilized NgPAC2. • Photo-induced Tyr–Tyr cross-linking to o,o′-dityrosine in lyophilized NgPAC2. • Photo-induced partial flavin cofactor reduction in lyophilized NgPAC2. • Two NgPAC2 conformations with fast and slow photo-induced electron transfer. - Abstract: The absorption and emission spectroscopic behavior of lyophilized photo-activated adenylate cyclase NgPAC2 from the amoeboflagellate Naegleria gruberi NEG-M strain consisting of a BLUF domain (BLUF = Blue Light sensor Using Flavin) and a cyclase homology domain was studied in the dark, during blue-light exposure and after blue-light exposure at a temperature of 4 °C. The BLUF domain photo-cycle dynamics observed for snap-frozen NgPAC2 was lost by lyophilization (no signaling state formation with flavin absorption red-shift). Instead, blue-light photo-excitation of lyophilized NgPAC2 caused sterically restricted Tyr–Tyr cross-linking (o,o′-ditysosine formation) and partial flavin cofactor reduction

Adsorption of N-nitrosodimethylamine precursors by powdered and granular activated carbon.

Science.gov (United States)

Hanigan, David; Zhang, Jinwei; Herckes, Pierre; Krasner, Stuart W; Chen, Chao; Westerhoff, Paul

2012-11-20

Activated carbon (AC) has been shown to remove precursors of halogenated disinfection byproducts. Granular and powdered activated carbon (GAC, PAC) were investigated for their potential to adsorb N-nitrosodimethylamine (NDMA) precursors from blends of river water and effluent from a wastewater treatment plant (WWTP). At bench scale, waters were exposed to lignite or bituminous AC, either as PAC in bottle point experiments or as GAC in rapid small-scale column tests (RSSCTs). NDMA formation potential (FP) was used as a surrogate for precursor removal. NDMA FP was reduced by 37, 59, and 91% with 3, 8, and 75 mg/L of one PAC, respectively, with a 4-h contact time. In RSSCTs and in full-scale GAC contactors, NDMA FP removal always exceeded that of the bulk dissolved organic carbon (DOC) and UV absorbance at 254 nm. For example, whereas DOC breakthrough exceeded 90% of its influent concentration after 10,000 bed volumes of operation in an RSSCT, NDMA FP was less than 40% of influent concentration after the same bed life of the GAC. At full or pilot scale, high NDMA FP reduction ranging from >60 to >90% was achieved across GAC contactors, dependent upon the GAC bed life and/or use of a preoxidant (chlorine or ozone). In all experiments, NDMA formation was not reduced to zero, which suggests that although some precursors are strongly sorbed, others are not. This is among the first studies to show that AC is capable of adsorbing NDMA precursors, but further research is needed to better understand NDMA precursor chemical properties (e.g., hydrophobicity, molecular size) and evaluate how best to incorporate this finding into full-scale designs and practice.

Towards a theory of PACS deployment: an integrative PACS maturity framework.

Science.gov (United States)

van de Wetering, Rogier; Batenburg, Ronald

2014-06-01

Owing to large financial investments that go along with the picture archiving and communication system (PACS) deployments and inconsistent PACS performance evaluations, there is a pressing need for a better understanding of the implications of PACS deployment in hospitals. We claim that there is a gap in the research field, both theoretically and empirically, to explain the success of the PACS deployment and maturity in hospitals. Theoretical principles are relevant to the PACS performance; maturity and alignment are reviewed from a system and complexity perspective. A conceptual model to explain the PACS performance and a set of testable hypotheses are then developed. Then, structural equation modeling (SEM), i.e. causal modeling, is applied to validate the model and hypotheses based on a research sample of 64 hospitals that use PACS, i.e. 70 % of all hospitals in the Netherlands. Outcomes of the SEM analyses substantiate that the measurements of all constructs are reliable and valid. The PACS alignment-modeled as a higher-order construct of five complementary organizational dimensions and maturity levels-has a significant positive impact on the PACS performance. This result is robust and stable for various sub-samples and segments. This paper presents a conceptual model that explains how alignment in deploying PACS in hospitals is positively related to the perceived performance of PACS. The conceptual model is extended with tools as checklists to systematically identify the improvement areas for hospitals in the PACS domain. The holistic approach towards PACS alignment and maturity provides a framework for clinical practice.

Effect of effluent organic matter on the adsorption of perfluorinated compounds onto activated carbon

International Nuclear Information System (INIS)

Yu, Jing; Lv, Lu; Lan, Pei; Zhang, Shujuan; Pan, Bingcai; Zhang, Weiming

2012-01-01

Highlights: ► The presence of EfOM significantly reduced the adsorption capacities and rates of PFCs. ► Low-molecular-weight EfOM compounds ( 30 kDa) affect the adsorption through pore blockage or restriction effect. ► Changes in surface properties of PAC caused by preloaded EfOM could affect PFCs adsorption. - Abstract: Effect of effluent organic matter (EfOM) on the adsorption of perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) onto powdered activated carbon (PAC) was quantitatively investigated at environmentally relevant concentration levels. The adsorption of both perfluorinated compounds (PFCs) onto PAC followed pseudo-second order kinetics and fitted the Freundlich model well under the given conditions. Intraparticle diffusion was found to be the rate-controlling step in the PFC adsorption process onto PAC in the absence and presence of EfOM. The presence of EfOM, either in PFC–EfOM simultaneous adsorption onto fresh PAC or in PFC adsorption onto EfOM-preloaded PAC, significantly reduced the adsorption capacities and sorption rates of PFCs. The pH of zero point of charge was found to be 7.5 for fresh PAC and 4.2 for EfOM-preloaded PAC, suggesting that the adsorbed EfOM imparted a negative charge on PAC surface. The effect of molecular weight distribution of EfOM on the adsorption of PFCs was investigated with two EfOM fractions obtained by ultrafiltration. The low-molecular-weight compounds ( 30 kDa) had much less effect on PFC adsorption capacity.

Overview of PACS

Science.gov (United States)

Vanden Brink, John A.

1995-08-01

Development of the DICOM standard and incremental developments in workstation, network, compression, archiving, and digital x-ray technology have produced cost effective image communication possibilities for selected medical applications. The emerging markets include modality PACS, mini PACS, and teleradiology. Military and VA programs lead the way in the move to adopt PACS technology. Commercial markets for PACS components and PAC systems are at LR400 million growing to LR500 million in 1996.

Chromium (Ⅵ) removal from aqueous solutions through powdered activated carbon countercurrent two-stage adsorption.

Science.gov (United States)

Wang, Wenqiang

2018-01-01

To exploit the adsorption capacity of commercial powdered activated carbon (PAC) and to improve the efficiency of Cr(VI) removal from aqueous solutions, the adsorption of Cr(VI) by commercial PAC and the countercurrent two-stage adsorption (CTA) process was investigated. Different adsorption kinetics models and isotherms were compared, and the pseudo-second-order model and the Langmuir and Freundlich models fit the experimental data well. The Cr(VI) removal efficiency was >80% and was improved by 37% through the CTA process compared with the conventional single-stage adsorption process when the initial Cr(VI) concentration was 50 mg/L with a PAC dose of 1.250 g/L and a pH of 3. A calculation method for calculating the effluent Cr(VI) concentration and the PAC dose was developed for the CTA process, and the validity of the method was confirmed by a deviation of <5%. Copyright © 2017. Published by Elsevier Ltd.

Alternative Splicing of the Pituitary Adenylate Cyclase-Activating Polypeptide Receptor PAC1: Mechanisms of Fine Tuning of Brain Activity

Directory of Open Access Journals (Sweden)

Janna eBlechman

2013-05-01

Full Text Available Alternative splicing of the precursor mRNA encoding for the neuropeptide receptor PAC1/ADCYAP1R1 generates multiple protein products that exhibit pleiotropic activities. Recent studies in mammals and zebrafish have implicated some of these splice isoforms in control of both cellular and body homeostasis. Here, we review the regulation of PAC1 splice variants and their underlying signal transduction and physiological processes in the nervous system.

Preparation of granular activated carbons from composite of powder activated carbon and modified β-zeolite and application to heavy metals removal.

Science.gov (United States)

Seyedein Ghannad, S M R; Lotfollahi, M N

2018-03-01

Heavy metals are continuously contaminating the surface and subsurface water. The adsorption process is an attractive alternative for removing the heavy metals because of its low cost, simple operation, high efficiency, and flexible design. In this study, influences of β-zeolite and Cu-modified β-zeolite on preparation of granular activated carbons (GACs) from a composite of powder activated carbon (PAC), methylcellulose as organic binder, bentonite as inorganic binder, and water were investigated. A number of granular samples were prepared by controlling the weight percentage of binder materials, PAC and zeolites as a reinforcing adsorbent. Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction techniques were employed to characterize zeolite, modified zeolite and produced GAC. The produced GACs were used as the adsorbent for removal of Zn +2 , Cd 2+ and Pb 2+ ions from aqueous solutions. The results indicated that the adsorption of metals ions depended on the pH (5.5) and contact time (30 min). Maximum adsorption of 97.6% for Pb 2+ , 95.9% for Cd 2+ and 91.1% for Zn +2 occurred with a new kind of GAC made of Cu-modified β-zeolite. The Zn +2 , Cd 2+ and Pb 2+ ions sorption kinetics data were well described by a pseudo-second order model for all sorbents. The Langmuir and Freundlich isotherm models were applied to analyze the experimental equilibrium data.

Micro-milling of spent granular activated carbon for its possible reuse as an adsorbent: Remaining capacity and characteristics.

Science.gov (United States)

Pan, Long; Takagi, Yuichi; Matsui, Yoshihiko; Matsushita, Taku; Shirasaki, Nobutaka

2017-05-01

We milled granular activated carbons (GACs) that had been used for 0-9 years in water treatment plants and produced carbon particles with different sizes and ages: powdered activated carbons (PAC, median diameter 12-42 μm), superfine PAC (SPAC, 0.9-3.5 μm), and submicron-sized SPAC (SSPAC, 220-290 nm). The fact that SPAC produced from 1-year-old GAC and SSPAC from 2-year-old GAC removed 2-methylisoborneol (MIB) from water with an efficiency similar to that of virgin PAC after a carbon contact time of 30 min suggests that spent GAC could be reused for water treatment after being milled. This potential for reuse was created by increasing the equilibrium adsorption capacity via reduction of the carbon particle size and improving the adsorption kinetics. During long-term (>1 year) use in GAC beds, the volume of pores in the carbon, particularly pores with widths of 0.6-0.9 nm, was greatly reduced. The equilibrium adsorption capacities of the carbon for compounds with molecular sizes in this range could therefore decrease with increasing carbon age. Among these compounds, the decreases of capacities were prominent for hydrophobic compounds, including MIB. For hydrophobic compounds, however, the equilibrium adsorption capacities could be increased with decreasing carbon particle size. The iodine number, among other indices, was best correlated with the equilibrium adsorption capacity of the MIB and would be a good index to assess the remaining MIB adsorption capacity of spent carbon. Spent GAC can possibly be reused as SPAC or SSPAC if its iodine number is ≥ 600 mg/g. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of Powdered Activated Carbon to Reduce Fouling in Membrane Bioreactors: A Sustainable Solution. Case Study

Directory of Open Access Journals (Sweden)

Giuseppe Mancini

2013-04-01

Full Text Available Membrane Bio Reactors (MBRs are mainly used for industrial wastewaters applications where their costs can be more easily afforded. High costs are basically due to energy consumption and membrane cleaning or replacement. Membrane fouling is responsible for reducing treated water production and increasing maintenance as well as operation costs. According to previous researches, the addition of Powdered Activated Carbon (PAC in high dosages could reduce membrane fouling; but such concentrations are economically unsustainable for operative conditions. A MBR pilot plant, fed by mixed liquor of a full-scale activated sludge process from a municipal wastewater treatment plant, was operated dosing low PAC concentrations (0, 2, 5, 10 and 20 mg·L−1, respectively. Experiments were also carried out at two different temperatures corresponding to summer and winter conditions. Results indicated that PAC addition was effective at the low dosages (2 and 5 mg·L−1 by reducing the permeate flux loss (from 16 up to 27%, respectively while higher PAC concentrations turns out in a useless cost increase.

Adsorption uptake of synthetic organic chemicals by carbon nanotubes and activated carbons

Science.gov (United States)

Brooks, A. J.; Lim, Hyung-nam; Kilduff, James E.

2012-07-01

Carbon nanotubes (CNTs) have shown great promise as high performance materials for adsorbing priority pollutants from water and wastewater. This study compared uptake of two contaminants of interest in drinking water treatment (atrazine and trichloroethylene) by nine different types of carbonaceous adsorbents: three different types of single walled carbon nanotubes (SWNTs), three different sized multi-walled nanotubes (MWNTs), two granular activated carbons (GACs) and a powdered activated carbon (PAC). On a mass basis, the activated carbons exhibited the highest uptake, followed by SWNTs and MWNTs. However, metallic impurities in SWNTs and multiple walls in MWNTs contribute to adsorbent mass but do not contribute commensurate adsorption sites. Therefore, when uptake was normalized by purity (carbon content) and surface area (instead of mass), the isotherms collapsed and much of the CNT data was comparable to the activated carbons, indicating that these two characteristics drive much of the observed differences between activated carbons and CNT materials. For the limited data set here, the Raman D:G ratio as a measure of disordered non-nanotube graphitic components was not a good predictor of adsorption from solution. Uptake of atrazine by MWNTs having a range of lengths and diameters was comparable and their Freundlich isotherms were statistically similar, and we found no impact of solution pH on the adsorption of either atrazine or trichloroethylene in the range of naturally occurring surface water (pH = 5.7-8.3). Experiments were performed using a suite of model aromatic compounds having a range of π-electron energy to investigate the role of π-π electron donor-acceptor interactions on organic compound uptake by SWNTs. For the compounds studied, hydrophobic interactions were the dominant mechanism in the uptake by both SWNTs and activated carbon. However, comparing the uptake of naphthalene and phenanthrene by activated carbon and SWNTs, size exclusion effects

Adsorption uptake of synthetic organic chemicals by carbon nanotubes and activated carbons

International Nuclear Information System (INIS)

Brooks, A J; Kilduff, James E; Lim, Hyung-nam

2012-01-01

Carbon nanotubes (CNTs) have shown great promise as high performance materials for adsorbing priority pollutants from water and wastewater. This study compared uptake of two contaminants of interest in drinking water treatment (atrazine and trichloroethylene) by nine different types of carbonaceous adsorbents: three different types of single walled carbon nanotubes (SWNTs), three different sized multi-walled nanotubes (MWNTs), two granular activated carbons (GACs) and a powdered activated carbon (PAC). On a mass basis, the activated carbons exhibited the highest uptake, followed by SWNTs and MWNTs. However, metallic impurities in SWNTs and multiple walls in MWNTs contribute to adsorbent mass but do not contribute commensurate adsorption sites. Therefore, when uptake was normalized by purity (carbon content) and surface area (instead of mass), the isotherms collapsed and much of the CNT data was comparable to the activated carbons, indicating that these two characteristics drive much of the observed differences between activated carbons and CNT materials. For the limited data set here, the Raman D:G ratio as a measure of disordered non-nanotube graphitic components was not a good predictor of adsorption from solution. Uptake of atrazine by MWNTs having a range of lengths and diameters was comparable and their Freundlich isotherms were statistically similar, and we found no impact of solution pH on the adsorption of either atrazine or trichloroethylene in the range of naturally occurring surface water (pH = 5.7–8.3). Experiments were performed using a suite of model aromatic compounds having a range of π-electron energy to investigate the role of π–π electron donor–acceptor interactions on organic compound uptake by SWNTs. For the compounds studied, hydrophobic interactions were the dominant mechanism in the uptake by both SWNTs and activated carbon. However, comparing the uptake of naphthalene and phenanthrene by activated carbon and SWNTs, size exclusion

PACS in nuclear medicine

International Nuclear Information System (INIS)

Kang, Keon Wook

2000-01-01

PACS (Picture Archiving and Communication System) is being rapidly spread and installed in many hospitals, but most of the system do not include nuclear medicine field. Although additional costs of hardware for nuclear medicine PACS is low, the complexity in developing viewing software and little market have made the nuclear medicine PACS not popular. Most PACS utilize DICOM 3.0 as standard format, but standard format in nuclear medicine has been Interfile. Interfile should be converted into DICOM format if nuclear images are to be stored and visualized in most PACS. Nowadays, many vendors supply the DICOM option in gamma camera and PET. Several hospitals in Korea have already installed nucler PACS with DICOM, but only the screen captured images are supplied. Software for visualizing pseudo-color with color lookup tables and expressing with volume view should be developed to fulfill the demand of referring physicians and nuclear medicine physicians. PACS is going to integrate not only radiologic images but also endoscopic and pathologic images. Web and PC based PACS is now a trend and is much compatible with nuclear medicine PACS. Most important barrier for nuclear medicine PACS that we encounter is not a technical problem, but indifference of investor such as administrator of hospital or PACS. Now it is time to support and invest for the development of nuclear medicine PACS

In situ treatment with activated carbon reduces bioaccumulation in aquatic food chains.

Science.gov (United States)

Kupryianchyk, D; Rakowska, M I; Roessink, I; Reichman, E P; Grotenhuis, J T C; Koelmans, A A

2013-05-07

In situ activated carbon (AC) amendment is a new direction in contaminated sediment management, yet its effectiveness and safety have never been tested on the level of entire food chains including fish. Here we tested the effects of three different AC treatments on hydrophobic organic chemical (HOC) concentrations in pore water, benthic invertebrates, zooplankton, and fish (Leuciscus idus melanotus). AC treatments were mixing with powdered AC (PAC), mixing with granular AC (GAC), and addition-removal of GAC (sediment stripping). The AC treatments resulted in a significant decrease in HOC concentrations in pore water, benthic invertebrates, zooplankton, macrophytes, and fish. In 6 months, PAC treatment caused a reduction of accumulation of polychlorobiphenyls (PCB) in fish by a factor of 20, bringing pollutant levels below toxic thresholds. All AC treatments supported growth of fish, but growth was inhibited in the PAC treatment, which was likely explained by reduced nutrient concentrations, resulting in lower zooplankton (i.e., food) densities for the fish. PAC treatment may be advised for sites where immediate ecosystem protection is required. GAC treatment may be equally effective in the longer term and may be adequate for vulnerable ecosystems where longer-term protection suffices.

dicomPACS: PACS Leader in Germany - Kodak Partner

OpenAIRE

Maziyar Shakeri

2007-01-01

History of Distributor: We are PDP Co. (Pardazesh Danesh Pezeshki) founded in 1998 with more than 8 years Experiments in Diagnostic Medical Imaging Market .we launched our New Division in 2002 for Digital Imaging and Softcopy under name of PDP View . We studied our market demands and PACS Provider Companies for 2 years and finally we signed the Contract with the first leader German PACS Provider named dicomPACS ® ."nWe are the only company who their 3 engineers well trained in th...

Towards a theory of PACS deployment: an integrative PACS maturity framework.

NARCIS (Netherlands)

Wetering, R. van de; Batenburg, R.

2014-01-01

Owing to large financial investments that go along with the picture archiving and communication system (PACS) deployments and inconsistent PACS performance evaluations, there is a pressing need for a better understanding of the implications of PACS deployment in hospitals. We claim that there is a

Adsorption of clofibric acid and ketoprofen onto powdered activated carbon: effect of natural organic matter.

Science.gov (United States)

Gao, Yaohuan; Deshusses, Marc A

2011-12-01

The adsorption of two acidic pharmaceutically active compounds (PhACs), clofibric acid and ketoprofen, onto powdered activated carbon (PAC) was investigated with a particular focus on the influence of natural organic matter (NOM) on the adsorption of the PhACs. Suwannee River humic acids (SRHAs) were used as a substitute for NOM. Batch adsorption experiments were conducted to obtain adsorption kinetics and adsorption isotherms with and without SRHAs in the system. The adsorption isotherms and adsorption kinetics showed that the adsorption ofclofibric acid was not significantly affected by the presence of SRHAs at a concentration of 5 mg (as carbon) L(-1). An adsorption capacity of 70 to 140 mg g(-1) was observed and equilibrium was reached within 48 h. In contrast, the adsorption of ketoprofen was markedly decreased (from about 120 mg g(-1) to 70-100 mg g(-1)) in the presence of SRHAs. Higher initial concentrations of clofibric acid than ketoprofen during testing may explain the different behaviours that were observed. Also, the more hydrophobic ketoprofen molecules may have less affinity for PAC when humic acids (which are hydrophilic) are present. The possible intermolecular forces that could account for the different behaviour of clofibric acid and ketoprofen adsorption onto PAC are discussed. In particular, the relevance of electrostatic forces, electron donor-acceptor interaction, hydrogen bonding and London dispersion forces are discussed

Effect of hydrophobicity of pharmaceuticals and personal care products for adsorption on activated carbon: Adsorption isotherms, kinetics and mechanism.

Science.gov (United States)

Kaur, Harkirat; Bansiwal, Amit; Hippargi, Girivyankatesh; Pophali, Girish R

2017-09-11

Adsorption of three pharmaceuticals and personal care products (PPCPs), namely caffeine, ibuprofen and triclosan on commercial powdered activated carbon was examined in aqueous medium. The contaminants were chosen based on their diverse log K ow (octanol-water partition coefficient) viz. - 0.07 for caffeine, 3.97 for ibuprofen and 4.76 for triclosan to examine the role of hydrophobicity on adsorption process. The adsorbent characterisation was achieved using BET surface area, SEM, pore size distribution studies and FTIR. Influence of mass of PAC, contact time, solution pH and initial concentration on adsorption capacity of PAC was studied. Adsorption isotherms and kinetics were applied to establish the mechanism of adsorption. The kinetics followed pseudo-second order with physisorption occurring through particle diffusion. The Freundlich model fitted best among the isotherm models. The adsorption capacity increased in the order CFN activated carbon.

Dental PACS development in Korea

International Nuclear Information System (INIS)

Kim, Eun Kyung

2008-01-01

Picture archiving and communication system (PACS) is an image information technology system for the transmission and storage of medical images. In Korea the first full PACS was installed at Samsung Medical Center in 1994, but, the rate of distribution was very slow. The government's approval for the medical insurance reimbursement for full PACS examinations in November 1999 became the turning point. Thereafter the number of hospitals with full PACS has steeply increased. In September of this year, PACS was installed at 906 medical institutes, including most of university hospitals and general hospitals. The first full dental PACS was installed at Wonkwang University Dental Hospital in 2002. Now ten out of eleven university dental hospitals implemented full dental PACS. The current status and technological factors of dental PACS in Korean university dental hospitals and the future perspectives of dental PACS are described.

Effects of recirculation in a three-tank pilot-scale system for pharmaceutical removal with powdered activated carbon.

Science.gov (United States)

Kårelid, Victor; Larsson, Gen; Björlenius, Berndt

2017-05-15

The removal of pharmaceutically active compounds by powdered activated carbon (PAC) in municipal wastewater is a promising solution to the problem of polluted recipient waters. Today, an efficient design strategy is however lacking with regard to high-level overall, and specific, substance removal in the large scale. The performance of PAC-based removal of pharmaceuticals was studied in pilot-scale with respect to the critical parameters; contact time and PAC dose using one PAC product selected by screening in bench-scale. The goal was a minimum of 95% removal of the pharmaceuticals present in the evaluated municipal wastewater. A set of 21 pharmaceuticals was selected from an initial 100 due to their high occurrence in the effluent water of two selected wastewater treatment plants (WWTPs) in Sweden, whereof candidates discussed for future EU regulation directives were included. By using recirculation of PAC over a treatment system using three sequential contact tanks, a combination of the benefits of powdered and granular carbon performance was achieved. The treatment system was designed so that recirculation could be introduced to any of the three tanks to investigate the effect of recirculation on the adsorption performance. This was compared to use of the setup, but without recirculation. A higher degree of pharmaceutical removal was achieved in all recirculation setups, both overall and with respect to specific substances, as compared to without recirculation. Recirculation was tested with nominal contact times of 30, 60 and 120 min and the goal of 95% removal could be achieved already at the shortest contact times at a PAC dose of 10-15 mg/L. In particular, the overall removal could be increased even to 97% and 99%, at 60 and 120 min, respectively, when the recirculation point was the first tank. Recirculation of PAC to either the first or the second contact tank proved to be comparable, while a slightly lower performance was observed with recirculation to

Modification of polystyrene-based activated carbon spheres to improve adsorption of dibenzothiophene

Science.gov (United States)

Wang, Qin; Liang, Xiaoyi; Qiao, Wenming; Liu, Chaojun; Liu, Xiaojun; Zhang, Rui; Ling, Licheng

2009-01-01

Polystyrene-based activated carbon spheres (PACS) were modified with either air, HNO 3, (NH 4) 2S 2O 8, H 2O 2 or H 2 to improve their adsorption properties of dibenzothiophene (DBT). The texture and surface chemistry of PACS were characterized by N 2 adsorption, scanning electron microscopy (SEM), temperature-programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), acid-base titration and elemental analysis. The results showed that HNO 3 and (NH 4) 2S 2O 8 treatments introduced large amount of acidic groups such as carboxylic, lactones and anhydride groups, while air and H 2O 2 had relatively mild effects and introduced a small quantity of phenol, carbonyl and ether groups. In the HNO 3 treatment, the acidic groups might be fixed on the internal and external surface of PACS, which may act as active sites of adsorption, resulting in increase of the adsorption amount by 45%. Whereas H 2O 2 and (NH 4) 2S 2O 8 treatments might fix more oxygen-containing groups on the external surface, which may hinder DBT molecule enter into micropores, leading to rather lower adsorption capacity with the extent of oxidation. So, the concentration, distribution and types of the acidic functional groups are responsible for the removal of DBT.

Shimadzu AI-PACS 'SAIPACS'

International Nuclear Information System (INIS)

Andoh, Minoru; Asai, Shigeya; Matsui, Norihisa; Nishida, Shinichiro; Horino, Masato

1990-01-01

The PACS-WS named SAIPACS-WS(workstation) has been developed as the first step of complete PACS. This SAIPACS-WS is different from other PACS-WS's, because this is including computer aided diagnostic reporting and computer aided diagnosis by using artificial intelligence technique. In this paper we will report detail of the SAIPACS-WS and discuss the future development of the total PACS setting the SAIPACS-WS in its center. (author)

Perfluorooctane sulfonate adsorption on powder activated carbon: Effect of phosphate (P) competition, pH, and temperature.

Science.gov (United States)

Qian, Jin; Shen, Mengmeng; Wang, Peifang; Wang, Chao; Li, Kun; Liu, Jingjing; Lu, Bianhe; Tian, Xin

2017-09-01

Powdered activated carbon (PAC), as an adsorbent, was applied to remove perfluorooctane sulfonate (PFOS) from aqueous solution. Laboratory batch experiments were performed to investigate the influences of phosphate (P) competition, temperature, and pH for PFOS adsorption onto PAC. The results showed that higher temperature favored PFOS adsorption in single and binary systems. The kinetic data fitted very well to the pseudo second-order kinetic model. Thermodynamically, the endothermic enthalpy of the PFOS adsorption in single and binary systems were 125.07 and 21.25 kJ mol -1 , respectively. The entropy of the PFOS adsorption in single and binary systems were 0.479 and 0.092 kJ mol -1  K -1 , respectively. And the Gibbs constants were negative. These results indicated that the adsorption processes were spontaneous. The adsorption isotherms of PFOS agreed well with the Langmuir model. In the single system, PFOS adsorption decreased with increased pH value. The difference in the amount of PFOS adsorption between the single and binary systems increased at higher pH. Frustrated total internal reflection (FTIR) demonstrated that P competition increased the hydrophilicity of the PAC and the electrostatic repulsion between PFOS and PAC, then the PFOS adsorption amount decreased. It also demonstrated that, at higher temperature, increased PFOS adsorption was mainly due to the higher diffusion rate of PFOS molecules and greater number of active sites opened on the PAC surface. Copyright © 2017 Elsevier Ltd. All rights reserved.

Reengineering the picture archiving and communication system (PACS) process for digital imaging networks PACS.

Science.gov (United States)

Horton, M C; Lewis, T E; Kinsey, T V

1999-05-01

Prior to June 1997, military picture archiving and communications systems (PACS) were planned, procured, and installed with key decisions on the system, equipment, and even funding sources made through a research and development office called Medical Diagnostic Imaging Systems (MDIS). Beginning in June 1997, the Joint Imaging Technology Project Office (JITPO) initiated a collaborative and consultative process for planning and implementing PACS into military treatment facilities through a new Department of Defense (DoD) contract vehicle called digital imaging networks (DIN)-PACS. The JITPO reengineered this process incorporating multiple organizations and politics. The reengineered PACS process administered through the JITPO transformed the decision process and accountability from a single office to a consultative method that increased end-user knowledge, responsibility, and ownership in PACS. The JITPO continues to provide information and services that assist multiple groups and users in rendering PACS planning and implementation decisions. Local site project managers are involved from the outset and this end-user collaboration has made the sometimes difficult transition to PACS an easier and more acceptable process for all involved. Corporately, this process saved DoD sites millions by having PACS plans developed within the government and proposed to vendors second, and then having vendors respond specifically to those plans. The integrity and efficiency of the process have reduced the opportunity for implementing nonstandard systems while sharing resources and reducing wasted government dollars. This presentation will describe the chronology of changes, encountered obstacles, and lessons learned within the reengineering of the PACS process for DIN-PACS.

PAC research in biology

Energy Technology Data Exchange (ETDEWEB)

Chain, C. Y., E-mail: yamil@fisica.unlp.edu.ar [Universidad Nacional de La Plata, IFLP (Argentina); Ceolin, M. [Instituto de Investigaciones Fisicoquimicas Teoricas y Aplicadas, Dto de Quimica, Fac. Cs. Exactas, UNLP (Argentina); Pasquevich, A. F. [Universidad Nacional de La Plata, IFLP (Argentina)

2008-01-15

In this paper possible applications of the Perturbed Angular Correlations (PAC) technique in Biology are considered. Previous PAC experiments in biology are globally analyzed. All the work that appears in the literature has been grouped in a few research lines, just to make the analysis and discussion easy. The commonly used radioactive probes are listed and the experimental difficulties are analyzed. We also report applications of {sup 181}Hf and {sup 111}In isotopes in life sciences other than their use in PAC. The possibility of extending these studies using the PAC technique is discussed.

Adsorption of selected pharmaceuticals and an endocrine disrupting compound by granular activated carbon. 2. Model prediction

Energy Technology Data Exchange (ETDEWEB)

Yu, Z.; Peldszus, S.; Huck, P.M. [University of Waterloo, Waterloo, ON (Canada). NSERC Chair in Water Treatment

2009-03-01

The adsorption of two representative pharmaceutically active compounds (PhACs) naproxen and carbamazepine and one endocrine disrupting compound (EDC) nonylphenol was studied in pilot-scale granular activated carbon (GAC) adsorbers using post-sedimentation (PS) water from a full-scale drinking water treatment plant. The GAC adsorbents were coal-based Calgon Filtrasorb 400 and coconut shell-based PICA CTIF TE. Acidic naproxen broke through fastest while nonylphenol was removed best, which was consistent with the degree to which fouling affected compound removals. Model predictions and experimental data were generally in good agreement for all three compounds, which demonstrated the effectiveness and robustness of the pore and surface diffusion model (PSDM) used in combination with the time-variable parameter approach for predicting removals at environmentally relevant concentrations (i.e., ng/L range). Sensitivity analyses suggested that accurate determination of film diffusion coefficients was critical for predicting breakthrough for naproxen and carbamazepine, in particular when high removals are targeted. Model simulations demonstrated that GAC carbon usage rates (CURs) for naproxen were substantially influenced by the empty bed contact time (EBCT) at the investigated conditions. Model-based comparisons between GAC CURs and minimum CURs for powdered activated carbon (PAC) applications suggested that PAC would be most appropriate for achieving 90% removal of naproxen, whereas GAC would be more suitable for nonylphenol. 25 refs., 4 figs., 1 tab.

A coagulation-powdered activated carbon-ultrafiltration - Multiple barrier approach for removing toxins from two Australian cyanobacterial blooms

International Nuclear Information System (INIS)

Dixon, Mike B.; Richard, Yann; Ho, Lionel; Chow, Christopher W.K.; O'Neill, Brian K.; Newcombe, Gayle

2011-01-01

Cyanobacteria are a major problem for the world wide water industry as they can produce metabolites toxic to humans in addition to taste and odour compounds that make drinking water aesthetically displeasing. Removal of cyanobacterial toxins from drinking water is important to avoid serious illness in consumers. This objective can be confidently achieved through the application of the multiple barrier approach to drinking water quality and safety. In this study the use of a multiple barrier approach incorporating coagulation, powdered activated carbon (PAC) and ultrafiltration (UF) was investigated for the removal of intracellular and extracellular cyanobacterial toxins from two naturally occurring blooms in South Australia. Also investigated was the impact of these treatments on the UF flux. In this multibarrier approach, coagulation was used to remove the cells and thus the intracellular toxin while PAC was used for extracellular toxin adsorption and finally the UF was used for floc, PAC and cell removal. Cyanobacterial cells were completely removed using the UF membrane alone and when used in conjunction with coagulation. Extracellular toxins were removed to varying degrees by PAC addition. UF flux deteriorated dramatically during a trial with a very high cell concentration; however, the flux was improved by coagulation and PAC addition.

Pituitary adenylate cyclase-activating polypeptide type 1 (PAC1) receptor is expressed during embryonic development of the earthworm.

Science.gov (United States)

Boros, Akos; Somogyi, Ildikó; Engelmann, Péter; Lubics, Andrea; Reglodi, Dóra; Pollák, Edit; Molnár, László

2010-03-01

Pituitary adenylate cyclase activating polypeptide (PACAP)-like molecules have been shown to be present in cocoon albumin and in Eisenia fetida embryos at an early developmental stage (E1) by immunocytochemistry and radioimmunoassay. Here, we focus on detecting the stage at which PAC1 receptor (PAC1R)-like immunoreactivity first appears in germinal layers and structures, e.g., various parts of the central nervous system (CNS), in developing earthworm embryos. PAC1R-like immunoreactivity was revealed by Western blot and Far Western blot as early as the E2 developmental stage, occurring in the ectoderm and later in specific neurons of the developing CNS. Labeled CNS neurons were first seen in the supraesophageal ganglion (brain) and subsequently in the subesophageal and ventral nerve cord ganglia. Ultrastructurally, PAC1Rs were located mainly on plasma membranes and intracellular membranes, especially on cisternae of the endoplasmic reticulum. Therefore, PACAP-like compounds probably influence the differentiation of germinal layers (at least the ectoderm) and of some neurons and might act as signaling molecules during earthworm embryonic development.

Effective Reuse of Electroplating Rinse Wastewater by Combining PAC with H2O2/UV Process.

Science.gov (United States)

Yen, Hsing Yuan; Kang, Shyh-Fang; Lin, Chen Pei

2015-04-01

This study evaluated the performance of treating electroplating rinse wastewater by powder activated carbon (PAC) adsorption, H2O2/UV oxidation, and their combination to remove organic compounds and heavy metals. The results showed that neither the process of PAC adsorption nor H2O2/UV oxidation could reduce COD to 100 mg/L, as enforced by the Taiwan Environmental Protection Agency. On the other hand, the water sample treated by the combined approach of using PAC (5 g/L) pre-adsorption and H2O2/UV post-oxidation (UV of 64 W, H2O2 of 100 mg/L, oxidation time of 90 min), COD and DOC were reduced to 8.2 mg/L and 3.8 mg/L, respectively. Also, the combined approach reduced heavy metals to meet the effluent standards and to satisfy the in-house water reuse criteria for the electroplating factory. The reaction constant analysis indicated that the reaction proceeded much more rapidly for the combined process. Hence, it is a more efficient, economic and environmentally friendly process.

Fitting PAC spectra with stochastic models: PolyPacFit

Energy Technology Data Exchange (ETDEWEB)

Zacate, M. O., E-mail: zacatem1@nku.edu [Northern Kentucky University, Department of Physics and Geology (United States); Evenson, W. E. [Utah Valley University, College of Science and Health (United States); Newhouse, R.; Collins, G. S. [Washington State University, Department of Physics and Astronomy (United States)

2010-04-15

PolyPacFit is an advanced fitting program for time-differential perturbed angular correlation (PAC) spectroscopy. It incorporates stochastic models and provides robust options for customization of fits. Notable features of the program include platform independence and support for (1) fits to stochastic models of hyperfine interactions, (2) user-defined constraints among model parameters, (3) fits to multiple spectra simultaneously, and (4) any spin nuclear probe.

PACS for imaging centers.

Science.gov (United States)

Farnsworth, T J

2003-01-01

PACS can be a difficult and confusing decision for any radiology provider, but it can be an even more dynamic question for an outpatient imaging center. Every center represents a unique situation and requires a specialized solution. Typically, most of what is said and discussed about PACS concentrates on solutions and requirements for hospital radiology facilities. Administrators of imaging centers have different problems from hospital administrators, and they need different answers. For imaging centers, the financial justification for PACS may be less immediate than for hospitals. The first thing that must be understood is that no PAC system can make a typical imaging center completely filmless, at least not for quite a while. A hospital has the ability to dictate to its internal referring physicians how a radiological study is delivered, whereas in an imaging center environment, the roles are very much reversed. Once the justification are made for the financial viability of PACS in an imaging center, the next question is how to finance the acquisition of PACS. The decision will depend on how you cost justify your PACS, as well as the shape of your business model, and it will come to a decision between capital purchase or contracting with an application service provider, or ASP. Historically, in the hospital-dominated marketplace, PAC systems have been treated as capital acquisitions. However, for most imaging center, owning the system is more of a problem than a benefit. ASPs increasingly represent a successful alternative for imaging centers. One of the biggest things to consider with PACS is how to store all of those images. There are typically two options, on-site and off-site, with a new "hybrid" option surfacing more recently. Each option has benefits for the user, but the benefits of off-site storage are increasing as the technology advances. Some of the benefits are data security and access. Other issues to address are HIPAA compliance, standardized

A comparative study of coagulation, granular- and powdered-activated carbon for the removal of perfluorooctane sulfonate and perfluorooctanoate in drinking water treatment.

Science.gov (United States)

Pramanik, Biplob Kumar; Pramanik, Sagor Kumar; Suja, Fatihah

2015-01-01

Perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) are persistent organic pollutants in the environment and their occurrence causes toxicological effects on humans. We examined different conventional coagulant treatments such as alum, ferric chloride and polyaluminium chloride in removing these compounds. These were then compared with a natural coagulant (Moringa oleifera). We also investigated the powdered-activated carbon (PAC) and granular-activated carbon (GAC) for removing these compounds. At an initial dose of 5 mg/L, polyaluminium chloride led to a higher reduction of PFOS/PFOA compared with alum which in turn was higher than ferric. The removal efficiency increased with the increase in coagulant dose and decrease in pH. M. oleifera was very effective in reducing PFOS and PFOA than conventional coagulants, with a reduction efficiencies of 65% and 72%, respectively, at a dose of 30 mg/L. Both PAC and GAC were very effective in reducing these compounds than coagulations. PAC led to a higher reduction in PFOS and PFOA than GAC due to its greater surface area and shorter internal diffusion distances. The addition of PAC (10 min contact time) with coagulation (at 5 mg/L dosage) significantly increased the removal efficiency, and the maximum removal efficiency was for M. oleifera with 98% and 94% for PFOS and PFOA, respectively. The reduction efficiency of PFOS/PFOA was reduced with the increase in dissolved organic concentration due to the adsorption competition between organic molecules and PFOS/PFOA.

PacCYP707A2 negatively regulates cherry fruit ripening while PacCYP707A1 mediates drought tolerance.

Science.gov (United States)

Li, Qian; Chen, Pei; Dai, Shengjie; Sun, Yufei; Yuan, Bing; Kai, Wenbin; Pei, Yuelin; He, Suihuan; Liang, Bin; Zhang, Yushu; Leng, Ping

2015-07-01

Sweet cherry is a non-climacteric fruit and its ripening is regulated by abscisic acid (ABA) during fruit development. In this study, four cDNAs (PacCYP707A1-4) encoding 8'-hydroxylase, a key enzyme in the oxidative catabolism of ABA, were identified in sweet cherry fruits using tobacco rattle virus-induced gene silencing (VIGS) and particle bombardment approaches. Quantitative real-time PCR confirmed significant down-regulation of target gene transcripts in VIGS-treated cherry fruits. In PacCYP707A2-RNAi-treated fruits, ripening and fruit colouring were promoted relative to control fruits, and both ABA accumulation and PacNCED1 transcript levels were up-regulated by 140%. Silencing of PacCYP707A2 by VIGS significantly altered the transcripts of both ABA-responsive and ripening-related genes, including the ABA metabolism-associated genes NCED and CYP707A, the anthocyanin synthesis genes PacCHS, PacCHI, PacF3H, PacDFR, PacANS, and PacUFGT, the ethylene biosynthesis gene PacACO1, and the transcription factor PacMYBA. The promoter of PacMYBA responded more strongly to PacCYP707A2-RNAi-treated fruits than to PacCYP707A1-RNAi-treated fruits. By contrast, silencing of PacCYP707A1 stimulated a slight increase in fruit colouring and enhanced resistance to dehydration stress compared with control fruits. These results suggest that PacCYP707A2 is a key regulator of ABA catabolism that functions as a negative regulator of fruit ripening, while PacCYP707A1 regulates ABA content in response to dehydration during fruit development. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

A strategic PACS maturity approach

NARCIS (Netherlands)

van de Wetering, R.

2011-01-01

Finding the key determinants of Picture Archivingand Communication Systems (PACS)performance in hospitals has been a conundrumfor decades. This research provides a method toassess the strategic alignment of PACS in hospitalsin order to find these key determinants. PACS touches upon every single part

Enhanced coagulation with powdered activated carbon or MIEX secondary treatment: a comparison of disinfection by-product formation and precursor removal.

Science.gov (United States)

Watson, Kalinda; Farré, Maria José; Knight, Nicole

2015-01-01

The removal of both organic and inorganic disinfection by-product (DBP) precursors prior to disinfection is important in mitigating DBP formation, with halide removal being particularly important in salinity-impacted water sources. A matrix of waters of variable alkalinity, halide concentration and dissolved organic carbon (DOC) concentration were treated with enhanced coagulation (EC) followed by anion exchange (MIEX resin) or powdered activated carbon (PAC) and the subsequent disinfection by-product formation potentials (DBP-FPs) assessed and compared to DBP-FPs for untreated samples. Halide and DOC removal were also monitored for both treatment processes. Bromide and iodide adsorption by MIEX treatment ranged from 0 to 53% and 4-78%, respectively. As expected, EC and PAC treatments did not remove halides. DOC removal by EC/PAC was 70 ± 10%, while EC/MIEX enabled a DOC removal of 66 ± 12%. Despite the halide removals achieved by MIEX, increases in brominated disinfection by-product (Br-DBP) formation were observed relative to untreated samples, when favourable Br:DOC ratios were created by the treatment. However, the increases in formation were less than what was observed for the EC/PAC treated waters, which caused large increases in Br-DBP formation when high Br-DBP-forming water quality conditions occurred. The formation potential of fully chlorinated DBPs decreased after treatment in all cases.

Assessment of PCDD/F and PBDD/F Emissions from Coal-fired Power Plants during Injection of Brominated Activated Carbon for Mercury Control

Science.gov (United States)

The effect of the injection of brominated powdered activated carbon (Br-PAC) on the emission of brominated and chlorinated dioxins and furans in coal combustion flue gas has been evaluated. The tests were performed at two U.S. Department of Energy (DOE) demonstration sites where ...

Modification of polystyrene-based activated carbon spheres to improve adsorption of dibenzothiophene

Energy Technology Data Exchange (ETDEWEB)

Wang Qin [State Key Laboratory of Chemical Engineering, East China University of Science and Technology, Meilong Road 130, Shanghai 200237 (China); Liang Xiaoyi [State Key Laboratory of Chemical Engineering, East China University of Science and Technology, Meilong Road 130, Shanghai 200237 (China)], E-mail: xyliang@ecust.edu.cn; Qiao Wenming; Liu Chaojun; Liu Xiaojun; Zhang Rui; Ling Licheng [State Key Laboratory of Chemical Engineering, East China University of Science and Technology, Meilong Road 130, Shanghai 200237 (China)

2009-01-01

Polystyrene-based activated carbon spheres (PACS) were modified with either air, HNO{sub 3}, (NH{sub 4}){sub 2}S{sub 2}O{sub 8}, H{sub 2}O{sub 2} or H{sub 2} to improve their adsorption properties of dibenzothiophene (DBT). The texture and surface chemistry of PACS were characterized by N{sub 2} adsorption, scanning electron microscopy (SEM), temperature-programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), acid-base titration and elemental analysis. The results showed that HNO{sub 3} and (NH{sub 4}){sub 2}S{sub 2}O{sub 8} treatments introduced large amount of acidic groups such as carboxylic, lactones and anhydride groups, while air and H{sub 2}O{sub 2} had relatively mild effects and introduced a small quantity of phenol, carbonyl and ether groups. In the HNO{sub 3} treatment, the acidic groups might be fixed on the internal and external surface of PACS, which may act as active sites of adsorption, resulting in increase of the adsorption amount by 45%. Whereas H{sub 2}O{sub 2} and (NH{sub 4}){sub 2}S{sub 2}O{sub 8} treatments might fix more oxygen-containing groups on the external surface, which may hinder DBT molecule enter into micropores, leading to rather lower adsorption capacity with the extent of oxidation. So, the concentration, distribution and types of the acidic functional groups are responsible for the removal of DBT.

Powdered activated carbon adsorption of two fishy odorants in water: Trans,trans-2,4-heptadienal and trans,trans-2,4-decadienal.

Science.gov (United States)

Li, Xin; Wang, Jun; Zhang, Xiaojian; Chen, Chao

2015-06-01

Powdered activated carbon (PAC) adsorption of two fishy odorants, trans,trans-2,4-heptadienal (HDE) and trans,trans-2,4-decadienal (DDE), was investigated. Both the pseudo first-order and the pseudo second-order kinetic models well described the kinetics curves, and DDE was more readily removed by PAC. In isotherm tests, both Freundlich and Modified Freundlich isotherms fitted the experimental data well. PAC exhibited a higher adsorption capacity for DDE than for HDE, which could be ascribed to the difference in their hydrophobicity. The calculated thermodynamic parameters (ΔG0, ΔH0, and ΔS0) indicated an exothermic and spontaneous adsorption process. PAC dosage, pH, and natural organic matter (NOM) presence were found to influence the adsorption process. With increasing PAC dosage, the pseudo first-order and pseudo second-order rate constants both increased. The value of pH had little influence on HDE or DDE molecules but altered the surface charge of PAC, and the maximum adsorption capacity occurred at pH9. The presence of NOM, especially the fraction with molecular weight less than 1k Dalton, hindered the adsorption. The study showed that preloaded NOM impaired the adsorption capacity of HDE or DDE more severely than simultaneously fed NOM did. Copyright © 2015. Published by Elsevier B.V.

PACS administrators' and radiologists' perspective on the importance of features for PACS selection.

Science.gov (United States)

Joshi, Vivek; Narra, Vamsi R; Joshi, Kailash; Lee, Kyootai; Melson, David

2014-08-01

Picture archiving and communication systems (PACS) play a critical role in radiology. This paper presents the criteria important to PACS administrators for selecting a PACS. A set of criteria are identified and organized into an integrative hierarchical framework. Survey responses from 48 administrators are used to identify the relative weights of these criteria through an analytical hierarchy process. The five main dimensions for PACS selection in order of importance are system continuity and functionality, system performance and architecture, user interface for workflow management, user interface for image manipulation, and display quality. Among the subdimensions, the highest weights were assessed for security, backup, and continuity; tools for continuous performance monitoring; support for multispecialty images; and voice recognition/transcription. PACS administrators' preferences were generally in line with that of previously reported results for radiologists. Both groups assigned the highest priority to ensuring business continuity and preventing loss of data through features such as security, backup, downtime prevention, and tools for continuous PACS performance monitoring. PACS administrators' next high priorities were support for multispecialty images, image retrieval speeds from short-term and long-term storage, real-time monitoring, and architectural issues of compatibility and integration with other products. Thus, next to ensuring business continuity, administrators' focus was on issues that impact their ability to deliver services and support. On the other hand, radiologists gave high priorities to voice recognition, transcription, and reporting; structured reporting; and convenience and responsiveness in manipulation of images. Thus, radiologists' focus appears to be on issues that may impact their productivity, effort, and accuracy.

Parents as Agents of Change (PAC in pediatric weight management: The protocol for the PAC randomized clinical trial

Directory of Open Access Journals (Sweden)

Ball Geoff D C

2012-08-01

Full Text Available Abstract Background There is an urgent need to develop and evaluate weight management interventions to address childhood obesity. Recent research suggests that interventions designed for parents exclusively, which have been named parents as agents of change (PAC approaches, have yielded positive outcomes for managing pediatric obesity. To date, no research has combined a PAC intervention approach with cognitive behavioural therapy (CBT to examine whether these combined elements enhance intervention effectiveness. This paper describes the protocol our team is using to examine two PAC-based interventions for pediatric weight management. We hypothesize that children with obesity whose parents complete a CBT-based PAC intervention will achieve greater reductions in adiposity and improvements in cardiometabolic risk factors, lifestyle behaviours, and psychosocial outcomes than children whose parents complete a psycho-education-based PAC intervention (PEP. Methods/Design This study is a pragmatic, two-armed, parallel, single-blinded, superiority, randomized clinical trial. The primary objective is to examine the differential effects of a CBT-based PAC vs PEP-based PAC intervention on children’s BMI z-score (primary outcome. Secondary objectives are to assess intervention-mediated changes in cardiometabolic, lifestyle, and psychosocial variables in children and parents. Both interventions are similar in frequency of contact, session duration, group facilitation, lifestyle behaviour goals, and educational content. However, the interventions differ insofar as the CBT-based intervention incorporates theory-based concepts to help parents link their thoughts, feelings, and behaviours; these cognitive activities are enabled by group leaders who possess formal training in CBT. Mothers and fathers of children (8–12 years of age; BMI ≥85th percentile are eligible to participate if they are proficient in English (written and spoken and agree for at least

Programa de Aceleração do Crescimento (PAC: um estudo descritivo sobre os desperdícios ativos e passivos = Growth Acceleration Program (PAC: a descriptive study of active and passive waste

Directory of Open Access Journals (Sweden)

Daniele Silva Rodrigues

2018-03-01

water resources. This program, in its first phase (2007-2010, contributed in a decisive way to the increase in the supply of jobs and in the generation of income in Brazil. However, according to "Instituto Trata Brasil" 86% of the sanitary sewage works from the PAC were paralyzed, or delayed or not started until December 2012. Also, in 2008 and 2009, through the special edition of the Inspection Program by Public Sweepstakes, the Federal Comptroller General's Office found several irregularities in 110 Brazilian municipalities covered with PAC funds. In this context, the objective of the study was to analyze the irregularities verified by the CGU, in the application of the federal resources destined to the sanitation and housing areas of the Brazilian municipalities through the first stage of the PAC. The main source of data for the survey were CGU's reports from the PAC and Census 2000 data, made available by IBGE. The techniques of Content analysis were used to classify the irregularities, verified by the CGU, in active waste (corruption and passive (mismanagement. The Descriptive statistics were used to analyze the profile of irregularities and the municipalities audited. It was observed that the most frequent wastes in the municipalities audited are those classified as Overbilling and Fraudulent Bidding (classified as active waste; and “Bad Administration” and “Irregular Bidding”, in the form of passive waste.

History of PACS in Asia

International Nuclear Information System (INIS)

Inamura, Kiyonari; Kim, Jong Hyo

2011-01-01

First, history of PACS (picture archiving and communication system for medical use) in Japan is described in two parts: in part 1, the early stage of PACS development from 1984 to 2002, and in part 2 the matured stage from 2002 to 2010. PACS in Japan has been developed and installed by local manufacturers by their own technology and demand from domestic hospitals. Part 1 mainly focuses on quantitative growth and part 2 on qualitative change. In part 2, integration of PACS into RIS (radiology information system), HIS (hospital information system), EPR (electronic patient record), teleradiology and IHE (integrating healthcare enterprise) is reported. Interaction with other elements of technology such as moving picture network system and three dimensional display is also discussed. Present situation of main 4 large size hospitals is presented. Second, history of PACS in Korea is reported. Very acute climbing up of filmless PACS diffusion was observed from 1997 to 2000. The reasons for such evolution are described and discussed. Also changes of PACS installation and system integration with other systems such as HIS and role of them in radiological diagnoses in Korea since 2002 are described. Third, history in China is investigated by checking international academic journals in English and described as far as events are logically linked and consistently meaningful.

MedPAC Data Book

Data.gov (United States)

U.S. Department of Health & Human Services — MedPACs Data Book is the result of discussions with congressional staff members regarding ways that MedPAC can better support them. Some of the information it...

Bacterial community evolutions driven by organic matter and powder activated carbon in simultaneous anammox and denitrification (SAD) process.

Science.gov (United States)

Ge, Cheng-Hao; Sun, Na; Kang, Qi; Ren, Long-Fei; Ahmad, Hafiz Adeel; Ni, Shou-Qing; Wang, Zhibin

2018-03-01

A distinct shift of bacterial community driven by organic matter (OM) and powder activated carbon (PAC) was discovered in the simultaneous anammox and denitrification (SAD) process which was operated in an anti-fouling submerged anaerobic membrane bio-reactor. Based on anammox performance, optimal OM dose (50 mg/L) was advised to start up SAD process successfully. The results of qPCR and high throughput sequencing analysis indicated that OM played a key role in microbial community evolutions, impelling denitrifiers to challenge anammox's dominance. The addition of PAC not only mitigated the membrane fouling, but also stimulated the enrichment of denitrifiers, accounting for the predominant phylum changing from Planctomycetes to Proteobacteria in SAD process. Functional genes forecasts based on KEGG database and COG database showed that the expressions of full denitrification functional genes were highly promoted in R C , which demonstrated the enhanced full denitrification pathway driven by OM and PAC under low COD/N value (0.11). Copyright © 2017 Elsevier Ltd. All rights reserved.

Vendor neutral archive in PACS

International Nuclear Information System (INIS)

Agarwal, Tapesh Kumar; Sanjeev

2012-01-01

An archive is a location containing a collection of records, documents, or other materials of historical importance. An integral part of Picture Archiving and Communication System (PACS) is archiving. When a hospital needs to migrate a PACS vendor, the complete earlier data need to be migrated in the format of the newly procured PACS. It is both time and money consuming. To address this issue, the new concept of vendor neutral archive (VNA) has emerged. A VNA simply decouples the PACS and workstations at the archival layer. This is achieved by developing an application engine that receives, integrates, and transmits the data using the different syntax of a Digital Imaging and Communication in Medicine (DICOM) format. Transferring the data belonging to the old PACS to a new one is performed by a process called migration of data. In VNA, a number of different data migration techniques are available to facilitate transfer from the old PACS to the new one, the choice depending on the speed of migration and the importance of data. The techniques include simple DICOM migration, prefetch-based DICOM migration, medium migration, and the expensive non-DICOM migration. “Vendor neutral” may not be a suitable term, and “architecture neutral,” “PACS neutral,” “content neutral,” or “third-party neutral” are probably better and preferred terms. Notwithstanding this, the VNA acronym has come to stay in both the medical IT user terminology and in vendor nomenclature, and radiologists need to be aware of its impact in PACS across the globe

Current status and installation of dental PACS

International Nuclear Information System (INIS)

Park, Chang Seo; Kim, Kee Deog; Park, Hyok; Jeong, Ho Gul

2004-01-01

Picture Archiving and Communication System (PACS) is difficult to implement in the best of situations, but evidence is growing that the benefits are significant. The aims of this study are to analyze the current status of full PACS and establish successful installation standard of dental PACS. Materials and Methods were based on the investigation of current working status and installation standard of PACS, and observation of variable issues to installation of dental PACS. By September 30, 2004, full PACS implementations in their facilities were 88.1% in specialized general hospitals (37 installations out of total 42 hospitals), 59.8% in general hospitals (144 installations out of total 241 hospitals), 12.3% in medical hospitals (116 installations out of total 941 hospitals) and 3.6% in dental hospitals (4 installations out of total 110 hospitals). Only 4 university dental hospitals currently have installed and are operating full PACS. Major obstacle to wide spread of dental PACS is initial high investments. Clinical environments of dental PACS differed from medical situation. Because of characteristic dental practice, the initial investments for dental PACS are generally much greater than those of medical PACS. Also new economic crisis makes users scruple. The best way to overcome these limitations is to establish an economic installation standard for dental PACS. Also the clear technical communication between the customer and the supplier before both sides are committed to the obstacles are critical to its success.

Removal of surfactants from water by adsorption on activated carbon and advanced oxidation process; Eliminacion de surfactantes de las aguas mediante adsorcion sobre carbon activado y oxidacion avanzada

Energy Technology Data Exchange (ETDEWEB)

Mendez Diaz, J. D.; Sanchez Polo, M.; Rivera Utrilla, J.; Bautista, M. I.

2007-07-01

The objective of this study was to analyze the elimination process of surfactants from water, using sodium dode-cilbencenesulfonate (SDBS) as model compound, by means of adsorption on activated carbons as well as different processes of advanced oxidation (O{sub 3}, O{sub 3}/H{sub 2}O{sub 2} and O{sub 3}/activated carbon). Results obtained have shown that the activated carbons used have a high efficiency to eliminate SDBS from waters which was enhanced when the adsorption process was carried out in the presence of bacteria. With regard to the oxidation processes studied, the results have indicated that the efficiency in the elimination of SDBS from water of the system based on the simultaneous use of O{sub 3} and powder activated carbon (PAC) is much higher than those of the other systems studied (O{sub 3},O{sub 3}/H{sub 2}O{sub 2}). (Author) 15 refs.

History of PACS in Asia.

Science.gov (United States)

Inamura, Kiyonari; Kim, Jong Hyo

2011-05-01

First, history of PACS (picture archiving and communication system for medical use) in Japan is described in two parts: in part 1, the early stage of PACS development from 1984 to 2002, and in part 2 the matured stage from 2002 to 2010. PACS in Japan has been developed and installed by local manufacturers by their own technology and demand from domestic hospitals. Part 1 mainly focuses on quantitative growth and part 2 on qualitative change. In part 2, integration of PACS into RIS (radiology information system), HIS (hospital information system), EPR (electronic patient record), teleradiology and IHE (integrating healthcare enterprise) is reported. Interaction with other elements of technology such as moving picture network system and three dimensional display is also discussed. Present situation of main 4 large size hospitals is presented. Second, history of PACS in Korea is reported. Very acute climbing up of filmless PACS diffusion was observed from 1997 to 2000. The reasons for such evolution are described and discussed. Also changes of PACS installation and system integration with other systems such as HIS and role of them in radiological diagnoses in Korea since 2002 are described. Third, history in China is investigated by checking international academic journals in English and described as far as events are logically linked and consistently meaningful. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Reliability issues in PACS

Science.gov (United States)

Taira, Ricky K.; Chan, Kelby K.; Stewart, Brent K.; Weinberg, Wolfram S.

1991-07-01

Reliability is an increasing concern when moving PACS from the experimental laboratory to the clinical environment. Any system downtime may seriously affect patient care. The authors report on the several classes of errors encountered during the pre-clinical release of the PACS during the past several months and present the solutions implemented to handle them. The reliability issues discussed include: (1) environmental precautions, (2) database backups, (3) monitor routines of critical resources and processes, (4) hardware redundancy (networks, archives), and (5) development of a PACS quality control program.

PACS quality control and automatic problem notifier

Science.gov (United States)

Honeyman-Buck, Janice C.; Jones, Douglas; Frost, Meryll M.; Staab, Edward V.

1997-05-01

One side effect of installing a clinical PACS Is that users become dependent upon the technology and in some cases it can be very difficult to revert back to a film based system if components fail. The nature of system failures range from slow deterioration of function as seen in the loss of monitor luminance through sudden catastrophic loss of the entire PACS networks. This paper describes the quality control procedures in place at the University of Florida and the automatic notification system that alerts PACS personnel when a failure has happened or is anticipated. The goal is to recover from a failure with a minimum of downtime and no data loss. Routine quality control is practiced on all aspects of PACS, from acquisition, through network routing, through display, and including archiving. Whenever possible, the system components perform self and between platform checks for active processes, file system status, errors in log files, and system uptime. When an error is detected or a exception occurs, an automatic page is sent to a pager with a diagnostic code. Documentation on each code, trouble shooting procedures, and repairs are kept on an intranet server accessible only to people involved in maintaining the PACS. In addition to the automatic paging system for error conditions, acquisition is assured by an automatic fax report sent on a daily basis to all technologists acquiring PACS images to be used as a cross check that all studies are archived prior to being removed from the acquisition systems. Daily quality control is preformed to assure that studies can be moved from each acquisition and contrast adjustment. The results of selected quality control reports will be presented. The intranet documentation server will be described with the automatic pager system. Monitor quality control reports will be described and the cost of quality control will be quantified. As PACS is accepted as a clinical tool, the same standards of quality control must be established

Cultural and semantic equivalence of the activity measure post-acute care (AM-PAC) after its translation into Mandarin Chinese.

Science.gov (United States)

Chang, Feng-Hang; Ni, Pengsheng; Chiou, Hung-Yi; Hou, Wen-Hsuan; Jette, Alan M

2018-03-21

The purpose of this study was to investigate the cultural and semantic equivalence of the Activity Measure Post-Acute Care (AM-PAC) outpatient short forms after they were translated from American English to Mandarin Chinese. This study was conducted with a composite sample of a group of 483 American adults (mean age 63.1 years, 42.4% males) and 553 Taiwanese adults (mean age 60.6 years, 47.2% males) who were undergoing home care or outpatient rehabilitation services. A confirmatory factor analysis tested the cultural equivalence of the AM-PAC dimensions between the US and Taiwanese samples. Semantic equivalence was tested through an item response theory-based differential item functioning (DFI) analysis. Results of the confirmatory factor analysis demonstrated good model-data fit of the AM-PAC in both the US and Taiwanese samples. Significant DFI was found for six Basic Mobility items, two Daily Activity items, and four Applied Cognition items. A DFI-adjusted conversion table was generated to transform the raw scores of the measure for comparisons between the two countries. This study provides evidence to support the conceptual equivalence of the AM-PAC when used in rehabilitation patients between American and Taiwanese cultural contexts. Some DFI items between the two groups were found, suggesting that some differences in semantic understanding of these items between cultures require cross-cultural adjustments. Implications for Rehabilitation Cultural equivalence needs to be tested before applying a clinical measure to another context. The findings of this study supported the three activity domains that the Activity Measure Post-Acute Care measures: Basic Mobility, Daily Activity, and Applied Cognition, which are all important rehabilitation outcomes that need to be assessed and monitored across rehabilitation settings. Differential item functioning was observed between the English and Chinese versions of the Activity Measure Post-Acute Care, indicating that

Radiative forcing associated with particulate carbon emissions resulting from the use of mercury control technology.

Science.gov (United States)

Lin, Guangxing; Penner, Joyce E; Clack, Herek L

2014-09-02

Injection of powdered activated carbon (PAC) adsorbents into the flue gas of coal fired power plants with electrostatic precipitators (ESPs) is the most mature technology to control mercury emissions for coal combustion. However, the PAC itself can penetrate ESPs to emit into the atmosphere. These emitted PACs have similar size and optical properties to submicron black carbon (BC) and thus could increase BC radiative forcing unintentionally. The present paper estimates, for the first time, the potential emission of PAC together with their climate forcing. The global average maximum potential emissions of PAC is 98.4 Gg/yr for the year 2030, arising from the assumed adoption of the maximum potential PAC injection technology, the minimum collection efficiency, and the maximum PAC injection rate. These emissions cause a global warming of 2.10 mW m(-2) at the top of atmosphere and a cooling of -2.96 mW m(-2) at the surface. This warming represents about 2% of the warming that is caused by BC from direct fossil fuel burning and 0.86% of the warming associated with CO2 emissions from coal burning in power plants. Its warming is 8 times more efficient than the emitted CO2 as measured by the 20-year-integrated radiative forcing per unit of carbon input (the 20-year Global Warming Potential).

Short history of PACS. Part I: USA

Energy Technology Data Exchange (ETDEWEB)

Huang, H.K., E-mail: hkhuang@aol.com [Departments of Radiology and Biomedical Engineering, University of Southern California (United States); Hong Kong Polytechnic University (Hong Kong); Shanghai Institute of Technical Physics, Chinese Academy of Sciences (China)

2011-05-15

This historical review covers the PACS development in the USA during the past 28 years from 1982 to 2010. General historical remarks of PACS and international scene in three stages from infancy, puberty to adolescence are presented. Early PACS development was mostly financed by the federal government including the National Institutes of Health (NIH) and the U.S. Army Medical Research and Materiel Command. PACS evolution went through several stages. The earliest stages included the definition of large-scale PACS, establishment of the DICOM and other standards, the development of some early key PACS related technologies, and PACS implementation strategies. The later stages were in the concept of enterprise PACS, IHE (Integrating the Healthcare Enterprise) workflow profiles, and ePR with image distribution. The current most excited accomplishment is in the development of the new field in medical imaging informatics. This review goes through these stages and events in the USA during these 28 years, whenever an event involved participants from other countries, the contributors are cited.

Short history of PACS. Part I: USA

International Nuclear Information System (INIS)

Huang, H.K.

2011-01-01

This historical review covers the PACS development in the USA during the past 28 years from 1982 to 2010. General historical remarks of PACS and international scene in three stages from infancy, puberty to adolescence are presented. Early PACS development was mostly financed by the federal government including the National Institutes of Health (NIH) and the U.S. Army Medical Research and Materiel Command. PACS evolution went through several stages. The earliest stages included the definition of large-scale PACS, establishment of the DICOM and other standards, the development of some early key PACS related technologies, and PACS implementation strategies. The later stages were in the concept of enterprise PACS, IHE (Integrating the Healthcare Enterprise) workflow profiles, and ePR with image distribution. The current most excited accomplishment is in the development of the new field in medical imaging informatics. This review goes through these stages and events in the USA during these 28 years, whenever an event involved participants from other countries, the contributors are cited.

Simultaneous removal of ammonia and N-nitrosamine precursors from high ammonia water by zeolite and powdered activated carbon.

Science.gov (United States)

Xue, Runmiao; Donovan, Ariel; Zhang, Haiting; Ma, Yinfa; Adams, Craig; Yang, John; Hua, Bin; Inniss, Enos; Eichholz, Todd; Shi, Honglan

2018-02-01

When adding sufficient chlorine to achieve breakpoint chlorination to source water containing high concentration of ammonia during drinking water treatment, high concentrations of disinfection by-products (DBPs) may form. If N-nitrosamine precursors are present, highly toxic N-nitrosamines, primarily N-nitrosodimethylamine (NDMA), may also form. Removing their precursors before disinfection should be a more effective way to minimize these DBPs formation. In this study, zeolites and activated carbon were examined for ammonia and N-nitrosamine precursor removal when incorporated into drinking water treatment processes. The test results indicate that Mordenite zeolite can remove ammonia and five of seven N-nitrosamine precursors efficiently by single step adsorption test. The practical applicability was evaluated by simulation of typical drinking water treatment processes using six-gang stirring system. The Mordenite zeolite was applied at the steps of lime softening, alum coagulation, and alum coagulation with powdered activated carbon (PAC) sorption. While the lime softening process resulted in poor zeolite performance, alum coagulation did not impact ammonia and N-nitrosamine precursor removal. During alum coagulation, more than 67% ammonia and 70%-100% N-nitrosamine precursors were removed by Mordenite zeolite (except 3-(dimethylaminomethyl)indole (DMAI) and 4-dimethylaminoantipyrine (DMAP)). PAC effectively removed DMAI and DMAP when added during alum coagulation. A combination of the zeolite and PAC selected efficiently removed ammonia and all tested seven N-nitrosamine precursors (dimethylamine (DMA), ethylmethylamine (EMA), diethylamine (DEA), dipropylamine (DPA), trimethylamine (TMA), DMAP, and DMAI) during the alum coagulation process. Copyright © 2017. Published by Elsevier B.V.

Short history of PACS. Part I: USA.

Science.gov (United States)

Huang, H K

2011-05-01

This historical review covers the PACS development in the USA during the past 28 years from 1982 to 2010. General historical remarks of PACS and international scene in three stages from infancy, puberty to adolescence are presented. Early PACS development was mostly financed by the federal government including the National Institutes of Health (NIH) and the U.S. Army Medical Research and Materiel Command. PACS evolution went through several stages. The earliest stages included the definition of large-scale PACS, establishment of the DICOM and other standards, the development of some early key PACS related technologies, and PACS implementation strategies. The later stages were in the concept of enterprise PACS, IHE (Integrating the Healthcare Enterprise) workflow profiles, and ePR with image distribution. The current most excited accomplishment is in the development of the new field in medical imaging informatics. This review goes through these stages and events in the USA during these 28 years, whenever an event involved participants from other countries, the contributors are cited. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Kinetic study of Chromium VI adsorption onto palm kernel shell activated carbon

Science.gov (United States)

Mohammad, Masita; Sadeghi Louyeh, Shiva; Yaakob, Zahira

2018-04-01

Heavy metal contamination of industrial effluent is one of the significant environmental problems due to their toxicity and its accumulation throughout the food chain. Adsorption is one of the promising methods for removal of heavy metals from aqua solution because of its simple technique, efficient, reliable and low-cost due to the utilization of residue from the agricultural industry. In this study, activated carbon from palm kernel shells has been produced through chemical activation process using zinc chloride as an activating agent and carbonized at 800 °C. Palm kernel shell activated carbon, PAC was assessed for its efficiency to remove Chromium (VI) ions from aqueous solutions through a batch adsorption process. The kinetic mechanisms have been analysed using Lagergren first-order kinetics model, second-order kinetics model and intra-particle diffusion model. The characterizations such as BET surface area, surface morphology, SEM-EDX have been done. The result shows that the activation process by ZnCl2 was successfully improved the porosity and modified the functional group of palm kernel shell. The result shows that the maximum adsorption capacity of Cr is 11.40mg/g at 30ppm initial metal ion concentration and 0.1g/50mL of adsorbent concentration. The adsorption process followed the pseudo second orders kinetic model.

Detoxification of Pesticide-Containing Wastewater with FeIII, Activated Carbon and Fenton Reagent and Its Control Using Three Standardized Bacterial Inhibition Tests

Directory of Open Access Journals (Sweden)

Eduard Rott

2017-12-01

Full Text Available Discharge of toxic industrial wastewaters into biological wastewater treatment plants may result in inhibition of activated sludge bacteria (ASB. In order to find an appropriate method of detoxification, the wastewater of a pesticide-processing plant in Vietnam was treated with three different methods (FeIII, powdered activated carbon (PAC, Fenton (FeII/H2O2 analyzing the detoxification effect with the nitrification inhibition test (NIT, respiration inhibition test (RIT and luminescent bacteria test (LBT. The heterotrophic ASB were much more resistant to the wastewater than the autotrophic nitrificants. The NIT turned out to be more suitable than the RIT since the NIT was less time-consuming and more reliable. In addition, the marine Aliivibrio fischeri were more sensitive than the nitrificants indicating that a lack of inhibition in the very practical and time-efficient LBT correlates with a lack of nitrification inhibition. With 95%, the Fenton method showed the highest efficiency regarding the chemical oxygen demand (COD removal. Although similar COD removal (60–65% was found for both the FeIII and the PAC method, the inhibitory effect of the wastewater was reduced much more strongly with PAC. Both the NIT and the LBT showed that the PAC and Fenton methods led to a similar reduction in the inhibitory effect.

Application of Pre-coated Microfiltration Ceramic Membrane with Powdered Activated Carbon for Natural Organic Matter Removal from Secondary Wastewater Effluent

KAUST Repository

Kurniasari, Novita

2012-12-01

Ceramic membranes offer more advantageous performances than conventional polymeric membranes. However, membrane fouling caused by Natural Organic Matters (NOM) contained in the feed water is still become a major problem for operational efficiency. A new method of ceramic membrane pre-coating with Powdered Activated Carbon (PAC), which allows extremely contact time for adsorbing aquatic contaminants, has been studied as a pre-treatment prior to ceramic microfiltration membrane. This bench scale study evaluated five different types of PAC (SA Super, G 60, KCU 6, KCU 8 and KCU 12,). The results showed that KCU 6 with larger pore size was performed better compared to other PAC when pre-coated on membrane surface. PAC pre-coating on the ceramic membrane with KCU 6 was significantly enhance NOM removal, reduced membrane fouling and improved membrane performance. Increase of total membrane resistance was suppressed to 96%. The removal of NOM components up to 92%, 58% and 56% for biopolymers, humic substances and building blocks, respectively was achieved at pre-coating dose of 30 mg/l. Adsorption was found to be the major removal mechanism of NOM. Results obtained showed that biopolymers removal are potentially correlated with enhanced membrane performance.

Pumpkin-Derived Porous Carbon for Supercapacitors with High Performance.

Science.gov (United States)

Bai, Suying; Tan, Guangqun; Li, Xiaoqin; Zhao, Qian; Meng, Yan; Wang, Yujue; Zhang, Yongzhi; Xiao, Dan

2016-06-21

Pumpkin has been employed for the first time as a renewable, low-cost precursor for the preparation of porous carbon materials with excellent performance. Unlike most other precursors, pumpkin is rich in sugars and starch, and it has advantageous properties for large-scale production. The as-prepared materials adopted a unique morphology that consisted of numerous fused sphere-like carbon grains with a high specific surface area (2968 m(2)  g(-1) ), abundant micro and mesopores, and excellent electrochemical properties. The pumpkin-derived activated carbon (PAC) material not only exhibited a high specific capacitance of 419 F g(-1) , but also showed considerable cycling stability, with 93.6 % retention after 10 000 cycles. Moreover, a symmetrical supercapacitor that was based on PAC showed a high energy density of 22.1 W h kg(-1) in aqueous electrolyte. These superior properties demonstrate that PAC holds great promise for applications in electrochemical energy-storage devices. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Altered circadian food anticipatory activity rhythms in PACAP receptor 1 (PAC1) deficient mice

DEFF Research Database (Denmark)

Hannibal, Jens; Georg, Birgitte; Fahrenkrug, Jan

2016-01-01

increase in amplitude compared to PAC1+/+ mice when placed in SPP at 300 lux. The same pattern of FAA was observed at 10 lux during both FPP and SPP. The present study indicates a role of PACAP/PAC1 signaling during light regulated FAA. Most likely, PACAP found in ipRGCs mediating non-image forming light...

Direct observation of solid-phase adsorbate concentration profile in powdered activated carbon particle to elucidate mechanism of high adsorption capacity on super-powdered activated carbon.

Science.gov (United States)

Ando, Naoya; Matsui, Yoshihiko; Matsushita, Taku; Ohno, Koichi

2011-01-01

Decreasing the particle size of powdered activated carbon (PAC) by pulverization increases its adsorption capacities for natural organic matter (NOM) and polystyrene sulfonate (PSS, which is used as a model adsorbate). A shell adsorption mechanism in which NOM and PSS molecules do not completely penetrate the adsorbent particle and instead preferentially adsorb near the outer surface of the particle has been proposed as an explanation for this adsorption capacity increase. In this report, we present direct evidence to support the shell adsorption mechanism. PAC particles containing adsorbed PSS were sectioned with a focused ion beam, and the solid-phase PSS concentration profiles of the particle cross-sections were directly observed by means of field emission-scanning electron microscopy/energy-dispersive X-ray spectrometry (FE-SEM/EDXS). X-ray emission from sulfur, an index of PSS concentration, was higher in the shell region than in the inner region of the particles. The X-ray emission profile observed by EDXS did not agree completely with the solid-phase PSS concentration profile predicted by shell adsorption model analysis of the PSS isotherm data, but the observed and predicted profiles were not inconsistent when the analytical errors were considered. These EDXS results provide the first direct evidence that PSS is adsorbed mainly in the vicinity of the external surface of the PAC particles, and thus the results support the proposition that the increase in NOM and PSS adsorption capacity with decreasing particle size is due to the increase in external surface area on which the molecules can be adsorbed. Copyright © 2010 Elsevier Ltd. All rights reserved.

Degradation of metaldehyde in water by nanoparticle catalysts and powdered activated carbon.

Science.gov (United States)

Li, Zhuojun; Kim, Jong Kyu; Chaudhari, Vrushali; Mayadevi, Suseeladevi; Campos, Luiza C

2017-07-01

Metaldehyde, an organic pesticide widely used in the UK, has been detected in drinking water in the UK with a low concentration (doped titanium dioxide nanocatalyst with different concentrations of carbon (C-1.5, C-40, and C-80) for metaldehyde removal from aqueous solutions by adsorption and oxidation via photocatalysis. PAC was found to be the most effective material which showed almost over 90% removal. Adsorption data were well fitted to the Langmuir isotherm model, giving a q m (maximum/saturation adsorption capacity) value of 32.258 mg g -1 and a K L (Langmuir constant) value of 2.013 L mg -1 . In terms of kinetic study, adsorption of metaldehyde by PAC fitted well with a pseudo-second-order equation, giving the adsorption rate constant k 2 value of 0.023 g mg -1  min -1 , implying rapid adsorption. The nanocatalysts were much less effective in oxidising metaldehyde than PAC with the same metaldehyde concentration and 0.2 g L -1 loading concentration of materials under UV light; the maximum removal achieved by carbon-doped titanium dioxide (C-1.5) nanocatalyst was around 15% for a 7.5 ppm metaldehyde solution. Graphical abstract ᅟ.

Adsorption of steroid micropollutants on polymer-based spherical activated carbon (PBSAC).

Science.gov (United States)

Tagliavini, Matteo; Engel, Fabio; Weidler, Peter Georg; Scherer, Torsten; Schäfer, Andrea Iris

2017-09-05

Removal and interaction mechanisms of four different steroid micropollutants, estrone (E1), estradiol (E2), progesterone (P) and testosterone (T) were determined for different types of polymer-based spherical activated carbon (PBSAC). Higher than 90% removal and significantly faster kinetics compared to conventional granular activated carbon (GAC) were observed, while performance was comparable with powdered activated carbon (PAC). No influence of pH in the range 2-12 was determined, while the presence of humic acid (HA) reduced both the removal and the kinetic by up to 20%. PBSAC was characterized in terms of morphology and material properties. The low oxygen content was identified as the main cause for the high performance observed. This was attributed to the enhancement of the hydrophobic effect between PBSAC and hormones and the reduced interactions between PBSAC and water. The ratio of micropollutant size (∼0.8nm) and average pore size (1-2nm) proved ideal for both micropollutant adsorption and HA exclusion. The homogenous size, spherical shape and surface smoothness of PBSAC did not influence adsorption negatively and make PBSAC a very promising sorbent for a vast range of applications, in particular for the removal of micropollutants in water treatment applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Picture archiving and communications systems (PACS)

International Nuclear Information System (INIS)

Huang, H.K.; Dwyer, S.J. III; Angus, W.M.; Capp, M.P.; Arenson, R.L.; Kangarloo, H.

1987-01-01

This special focus session discusses the current status of picture archiving and communication systems (PACS). The first presentation focuses on the technological advances in various PACS components. The second presentation concentrates on image archiving - what is required, what is available. The third talk is on the concept of a total digital radiology department in the past, the present, and the future. The fourth panelist discusses evaluating various imaging systems as PACS components for the intensive care unit. Finally, one hears about clinical experience with two operating PACS modules, one in pediatric radiology and the second in a coronary care unit

PACS on mobile devices

Science.gov (United States)

Parikh, Ashesh; Mehta, Nihal

2015-03-01

Recent advances in internet browser technologies makes it possible to incorporate advanced functionality of a traditional PACS for viewing DICOM medical images on standard web browsers without the need to pre-install any plug-ins, apps or software. We demonstrate some of the capabilities of standard web browsers setting the stage for a cloud-based PACS.

The sorting protein PACS-2 promotes ErbB signalling by regulating recycling of the metalloproteinase ADAM17

DEFF Research Database (Denmark)

Dombernowsky, Sarah Louise; Samsøe-Petersen, Jacob; Petersen, Camilla Hansson

2015-01-01

The metalloproteinase ADAM17 activates ErbB signalling by releasing ligands from the cell surface, a key step underlying epithelial development, growth and tumour progression. However, mechanisms acutely controlling ADAM17 cell-surface availability to modulate the extent of ErbB ligand release....... PACS-2 co-localizes with ADAM17 on early endosomes and PACS-2 knockdown decreases the recycling and stability of internalized ADAM17. Hence, PACS-2 sustains ADAM17 cell-surface activity by diverting ADAM17 away from degradative pathways. Interestingly, Pacs2-deficient mice display significantly reduced...

Evolutionistic or revolutionary paths? A PACS maturity model for strategic situational planning.

Science.gov (United States)

van de Wetering, Rogier; Batenburg, Ronald; Lederman, Reeva

2010-07-01

While many hospitals are re-evaluating their current Picture Archiving and Communication System (PACS), few have a mature strategy for PACS deployment. Furthermore, strategies for implementation, strategic and situational planning methods for the evolution of PACS maturity are scarce in the scientific literature. Consequently, in this paper we propose a strategic planning method for PACS deployment. This method builds upon a PACS maturity model (PMM), based on the elaboration of the strategic alignment concept and the maturity growth path concept previously developed in the PACS domain. First, we review the literature on strategic planning for information systems and information technology and PACS maturity. Secondly, the PMM is extended by applying four different strategic perspectives of the Strategic Alignment Framework whereupon two types of growth paths (evolutionistic and revolutionary) are applied that focus on a roadmap for PMM. This roadmap builds a path to get from one level of maturity and evolve to the next. An extended method for PACS strategic planning is developed. This method defines eight distinctive strategies for PACS strategic situational planning that allow decision-makers in hospitals to decide which approach best suits their hospitals' current situation and future ambition and what in principle is needed to evolve through the different maturity levels. The proposed method allows hospitals to strategically plan for PACS maturation. It is situational in that the required investments and activities depend on the alignment between the hospital strategy and the selected growth path. The inclusion of both strategic alignment and maturity growth path concepts make the planning method rigorous, and provide a framework for further empirical research and clinical practice.

The Detector Physics and Applications Center - DePAC

CERN Document Server

Plothow-Besch, H; Fiorini, C; Grupen, C; Hassard, J; Longoni, A; Walenta, Albert H

2001-01-01

A new project, the 'Detector Physics and Applications Center (DePAC)', is presented. DePAC is a general detector and sensor database, which is not application specific, on the Internet. DePAC collects and explains the physics, the technology and the application of a wide range of radiation detectors. DePAC also collects and describes information about noise problems, front-end electronics, data transfer, processing and storage. DePAC provides short write-ups and source code of all sorts of detector related software depending on availability. DePAC collects useful constants and properties of materials in an exhaustive series of tables and graphs. DePAC also acts as a point of contact for researchers and industry in an interdisciplinary way, e.g. in biology, in medicine, in materials research and in high energy or nuclear physics. Last but not least, DePAC aims to develop also into a virtual lecturing school and serves as a tutorial for students and all interested scientists.

The Detector Physics and Applications Center—DePAC

Science.gov (United States)

Plothow-Besch, H.; Besch, H.-J.; Fiorini, C.; Grupen, C.; Hassard, J.; Longoni, A.; Walenta, A. H.

2001-09-01

A new project, the "Detector Physics and Applications Center (DePAC)", is presented. DePAC is a general detector and sensor database, which is not application specific, on the Internet. DePAC collects and explains the physics, the technology and the application of a wide range of radiation detectors. DePAC also collects and describes information about noise problems, front-end electronics, data transfer, processing and storage. DePAC provides short write-ups and source code of all sorts of detector related software depending on availability. DePAC collects useful constants and properties of materials in an exhaustive series of tables and graphs. DePAC also acts as a point of contact for researchers and industry in an interdisciplinary way, e.g. in biology, in medicine, in materials research and in high energy or nuclear physics. Last but not least, DePAC aims to develop also into a virtual lecturing school and serves as a tutorial for students and all interested scientists.

The Detector Physics and Applications Center - DePAC

International Nuclear Information System (INIS)

Plothow-Besch, H.; Besch, H.-J.; Fiorini, C.; Grupen, C.; Hassard, J.; Longoni, A.; Walenta, A.H.

2001-01-01

A new project, the 'Detector Physics and Applications Center (DePAC)', is presented. DePAC is a general detector and sensor database, which is not application specific, on the Internet. DePAC collects and explains the physics, the technology and the application of a wide range of radiation detectors. DePAC also collects and describes information about noise problems, front-end electronics, data transfer, processing and storage. DePAC provides short write-ups and source code of all sorts of detector related software depending on availability. DePAC collects useful constants and properties of materials in an exhaustive series of tables and graphs. DePAC also acts as a point of contact for researchers and industry in an interdisciplinary way, e.g. in biology, in medicine, in materials research and in high energy or nuclear physics. Last but not least, DePAC aims to develop also into a virtual lecturing school and serves as a tutorial for students and all interested scientists

Enterprise imaging and multi-departmental PACS

International Nuclear Information System (INIS)

Bergh, Bjoern

2006-01-01

The aim of this review is to present the status of digital image acquisition and archiving outside of radiology and to describe the technical concepts and possibilities of how a ''radiology'' Picture Archiving and Communication System (PACS) can become a multi-departmental (MD-)PACS. First the principles of system integration technology are explained and illustrated by the description of a typical radiology system integration. Then four types of modality integration approaches are defined: the direct modality integration (Type-I), the integration via DICOM acquisition software (Type-II) the integration via specialised systems either with (Type-III) or without PACS connection (Type-IV). The last section is dedicated to the presentation of the PACS requirements of selected interdisciplinary modality types [Endoscopy, Ultrasound and Electrocardiography (ECG)] and clinical disciplines (Pathology, Dermatology, Ophthalmology and Cardiology), which are then compared with the technical possibilities of a MD-PACS. (orig.)

Trends in PACS architecture

International Nuclear Information System (INIS)

Bellon, Erwin; Feron, Michel; Deprez, Tom; Reynders, Reinoud; Van den Bosch, Bart

2011-01-01

Radiological Picture Archiving and Communication Systems (PACS) have only relatively recently become abundant. Many hospitals have made the transition to PACS about a decade ago. During that decade requirements and available technology have changed considerably. In this paper we look at factors that influence the design of tomorrow's systems, especially those in larger multidisciplinary hospitals. We discuss their impact on PACS architecture (a technological perspective) as well as their impact on radiology (a management perspective). We emphasize that many of these influencing factors originate outside radiology and that radiology has little impact on these factors. That makes it the more important for managers in radiology to be aware of architectural aspects and it may change cooperation of radiology with, among others, the hospital's central IT department.

Mechanism and kinetic considerations of TOC removal from the powdered activated carbon ozonation of diclofenac aqueous solutions.

Science.gov (United States)

Beltrán, Fernando J; Pocostales, J Pablo; Alvarez, Pedro M; Jaramillo, Josefa

2009-09-30

Ozonation of DCF in aqueous solution in the presence of powdered activated carbon (PAC) has been studied for mechanistic and kinetic purposes. The effects of gas flow rate, ozone gas concentration and initial TOC on the TOC elimination rate were then investigated. The use of PAC allows liquid-solid and internal diffusion mass transfer resistances being eliminated. Gas-liquid mass transfer resistance is also eliminated when ozonation is applied to DCF preozonated solutions. In the absence of mass transfer resistances a mechanism of reactions involving homogeneous and heterogeneous steps for TOC removal was proposed. From this mechanism a mathematical model constituted by mass balances of main species in water was established. Considerations about the changing nature of ozonation intermediates, as being promoters or inhibitors of ozone decomposition, is a key point to better predict the experimental concentrations of species present in this system.

A PACS maturity model: a systematic meta-analytic review on maturation and evolvability of PACS in the hospital enterprise.

NARCIS (Netherlands)

Wetering, R. van de; Batenburg, R.

2009-01-01

INTRODUCTION: With PACS and medical imaging technology maturing, the importance of organizational maturity and effective deployment of PACS in the hospital enterprise are becoming significant. OBJECTIVE: The objective of this paper is twofold. Firstly, PACS literature on maturity and evolvability in

Tuning the Pore Geometry of Ordered Mesoporous Carbons for Enhanced Adsorption of Bisphenol-A

Directory of Open Access Journals (Sweden)

Wannes Libbrecht

2015-04-01

Full Text Available Mesoporous carbons were synthesized via both soft and hard template methods and compared to a commercial powder activated carbon (PAC for the adsorption ability of bisphenol-A (BPA from an aqueous solution. The commercial PAC had a BET-surface of 1027 m2/g with fine pores of 3 nm and less. The hard templated carbon (CMK-3 material had an even higher BET-surface of 1420 m2/g with an average pore size of 4 nm. The soft templated carbon (SMC reached a BET-surface of 476 m2/g and a pore size of 7 nm. The maximum observed adsorption capacity (qmax of CMK-3 was the highest with 474 mg/g, compared to 290 mg/g for PAC and 154 mg/g for SMC. The difference in adsorption capacities was attributed to the specific surface area and hydrophobicity of the adsorbent. The microporous PAC showed the slowest adsorption, while the ordered mesopores of SMC and CMK-3 enhanced the BPA diffusion into the adsorbent. This difference in adsorption kinetics is caused by the increase in pore diameter. However, CMK-3 with an open geometry consisting of interlinked nanorods allows for even faster intraparticle diffusion.

Tuning the Pore Geometry of Ordered Mesoporous Carbons for Enhanced Adsorption of Bisphenol-A

Science.gov (United States)

Libbrecht, Wannes; Vandaele, Koen; De Buysser, Klaartje; Verberckmoes, An; Thybaut, Joris W.; Poelman, Hilde; De Clercq, Jeriffa; Van Der Voort, Pascal

2015-01-01

Mesoporous carbons were synthesized via both soft and hard template methods and compared to a commercial powder activated carbon (PAC) for the adsorption ability of bisphenol-A (BPA) from an aqueous solution. The commercial PAC had a BET-surface of 1027 m2/g with fine pores of 3 nm and less. The hard templated carbon (CMK-3) material had an even higher BET-surface of 1420 m2/g with an average pore size of 4 nm. The soft templated carbon (SMC) reached a BET-surface of 476 m2/g and a pore size of 7 nm. The maximum observed adsorption capacity (qmax) of CMK-3 was the highest with 474 mg/g, compared to 290 mg/g for PAC and 154 mg/g for SMC. The difference in adsorption capacities was attributed to the specific surface area and hydrophobicity of the adsorbent. The microporous PAC showed the slowest adsorption, while the ordered mesopores of SMC and CMK-3 enhanced the BPA diffusion into the adsorbent. This difference in adsorption kinetics is caused by the increase in pore diameter. However, CMK-3 with an open geometry consisting of interlinked nanorods allows for even faster intraparticle diffusion. PMID:28788023

PACS module image communication at UCLA

International Nuclear Information System (INIS)

Stewart, B.K.; Taira, R.K.; Cho, P.S.; Mankovich, N.J.

1987-01-01

The advent of the ACR-NEMA digital and communication standard for PACS implementation between imaging, storage and display devices may simplify the networking problems inherent to PACS in the future. However, since the ACR-NEMA interface has not been implemented in manufactured products, the components of a PACS at the present time use various network interface designs, requiring substantial effort in the area of hardware and software integration. Many communication systems are used for the PACS implementation in Pediatric Radiology at UCLA, including baseband, broadband, as well as various parallel-line interface protocols, e.g. GP-IB. A VAX 11/750 minicomputer serves as the host computer for the UCLA Pediatric Radiology PACS system. Communication between the many peripherals take place through the host computer, which acts as the central node. Several communication links have been established, primarily: host computer to other local computers, image processors, various peripherals (digitizers, storage media, etc.) and, of course, to the 512, 1024 and 2048 viewing stations

Experimental Study on Treatment of Dyeing Wastewater by Activated Carbon Adsorption, Coagulation and Fenton Oxidation

Science.gov (United States)

Xiaoxu, SUN; Jin, XU; Xingyu, LI

2017-12-01

In this paper dyeing waste water was simulated by reactive brilliant blue XBR, activated carbon adsorption process, coagulation process and chemical oxidation process were used to treat dyeing waste water. In activated carbon adsorption process and coagulation process, the water absorbance values were measured. The CODcr value of water was determined in Fenton chemical oxidation process. Then, the decolorization rate and COD removal rate were calculated respectively. The results showed that the optimum conditions of activated carbon adsorption process were as follows: pH=2, the dosage of activated carbon was 1.2g/L, the adsorption reaction time was 60 min, and the average decolorization rate of the three parallel experiments was 85.30%. The optimum conditions of coagulation experiment were as follows: pH=8~9, PAC dosage was 70mg/L, stirring time was 20min, standing time was 45min, the average decolorization rate of the three parallel experiments was 74.48%. The optimum conditions for Fenton oxidation were Fe2+ 0.05g/L, H2O2 (30%) 14mL/L, pH=3, reaction time 40min. The average CODcr removal rate was 69.35% in three parallel experiments. It can be seen that in the three methods the activated carbon adsorption treatment of dyeing wastewater was the best one.

Current developments in departmental PACS for ultrasound.

Science.gov (United States)

Grenier, L E; Eng, P

1995-01-01

1. INTRODUCTION TO DEPARTMENTAL PACS. Full or partial Departmental PACS is generally taken to mean an image management system focused on serving the needs of a specific modality or modality application. It will provide a modality specific means of image acquisition, specialized redisplay of images, distribution, and local long term storage of images. A Departmental PACS can be considered in isolation or as a component in a distributed Radiology PACS which consists of one or more departmental work groups on a back bone, potentially with shared resources. 2. DEPARTMENTAL PACS Issues Implementation of a Departmental PACS requires an in-depth knowledge of departmental clinical practice and work flow in all affected areas in the department, including patient intake, image collection, data routing, retrieval of previous image data, reporting, and long term data management and storage. Optimization of modality specific image display systems requires significant involvement from representative physician users. System architectures and user interfaces must be flexible enough to support the span of variation in clinical practice encountered in the site. A departmental PACS should offer a variety of "open" communications interfaces, both local and wide area, recognizing that outreach efforts are often driven by specific imaging departments. Interfaces to other departmental PAC systems and other information systems must be considered in order to facilitate institutions developing "Best of Breed" PACS systems. As hospitals move toward the integrated electronic medical record, means need to exist for a client process launched from a physician desktop to acquire images and/or reports from a departmental system. At minimum, HIS/RIS interfaces need to be considered to minimize re-keying of data and reduce data entry errors. 3. DESIGN OBJECTIVES FOR ALI ULTRAPACS. The key objectives were to design a product which could function either as a free standing PACS or as a departmental

PACS for the Developing World

Directory of Open Access Journals (Sweden)

Jeffrey B. Mendel

2015-11-01

Full Text Available Digital imaging is now firmly ensconced in the developed world. Its widespread adoption has enabled instant access to images, remote viewing, remote consultation, and the end of lost or misplaced film. Unfortunately, the current paradigm of Picture Archiving and Communication System (PACS, with advanced technology inseparable from high complexity, high purchase costs, and high maintenance costs, is not suited for the low-income developing world. Like the simple, easy to repair, 1950’s American cars still running on the streets of Havana, the developing world requires a PACS (DW-PACS that can perform basic functions and survive in a limited-resource environment. The purpose of this article is to more fully describe this concept and to present a blueprint for PACS tailored to the needs and resources of the developing world. This framework should assist both users looking for a vendor-supplied or open-source solutions and developers seeking to address the needs of this emerging market.

Current status of the UCSF second-generation PACS

Science.gov (United States)

Huang, H. K.; Arenson, Ronald L.; Wong, Albert W. K.; Bazzill, Todd M.; Lou, Shyhliang A.; Andriole, Katherine P.; Wang, Jun; Zhang, Jianguo; Wong, Stephen T. C.

1996-05-01

This paper describes the current status of the second generation PACS at UCSF commenced in October 1992. The UCSF PACS is designed in-house as a hospital-integrated PACS based on an open architecture concept using industrial standards including UNIX operating system, C programming language, X-Window user interface, TCP/IP communication protocol, DICOM 3.0 image standard and HL7 health data format. Other manufacturer's PACS components which conform with these standards can be easily integrated into the system. Relevant data from HIS and RIS is automatically incorporated into the PACS using HL7 data format and TCP/IP communication protocol. The UCSF system also takes advantage of state-of-the-art communication, storage, and software technologies in ATM, multiple storage media, automatic programming, multilevel processes for a better cost-performance system. The primary PACS network is the 155 Mbits/sec OC3 ATM with the Ethernet as the back-up. The UCSF PACS also connects Mt. Zion Hospital and San Francisco VA Medical Center in the San Francisco Bay area via an ATM wide area network with a T1 line as the back-up. Currently, five MR and five CT scanners from multiple sites, two computed radiography systems, two film digitizers, one US PACS module, the hospital HIS and the department RIS have been connected to the PACS network. The image data is managed by a mirrored database (Sybase). The PACS controller, with its 1.3 terabyte optical disk library, acquires 2.5 gigabytes digital data daily. Four 2K, five, 1,600-line multiple monitor display workstations are on line in neuroradiology, pediatric radiology and intensive care units for clinical use. In addition, the PACS supports over 100 Macintosh users in the department and selected hospital sites for both images and textual retrieval through a client/server mechanism. We are also developing a computation and visualization node in the PACS network for advancing radiology research.

A DICOM based PACS for nuclear medicine; Ein DICOM-basiertes PACS fuer die Nuklearmedizin

Energy Technology Data Exchange (ETDEWEB)

Lassmann, M.; Reiners, C. [Wuerzburg Univ. (Germany). Klinik und Poliklinik fuer Nuklearmedizin

2002-02-01

The installation of a radiology information system (RIS) connected to a hospital information system (HIS) and a picture archiving and communications system (PACS) seems mandatory for a nuclear medicine department in order to guarantee a high patient throughput. With these systems a fast transmission of reports, images to the in- and out-patients' wards and private practitioners is realized. Therefore, since April 2000, at the department of nuclear medicine of the university of Wuerzburg a completely DICOM based PACS has been implemented in addition to the RIS. With this system a DICOM based workflow is realized throughout the department of nuclear medicine for reporting and archiving. The PACS is connected to six gamma-cameras, a PET scanner, a bone densitometry system and an ultrasound device. The volume of image data archived per month is 4 GByte. Patient demographics are provided to the modalities via DICOM-Worklist. With these PACS components a department specific archive purely based on DICOM can be realized. During the installation process problems occurred mainly because of the complex DICOM standard for nuclear medicine. Related to that is the problem that most of the software implementations still contain bugs or are not adapted to the needs of a nuclear medicine department (particularly for PET). A communication software for the distribution of nuclear medicine reports and images based on techniques used for the worldwide web is currently tested. (orig.) [German] Fuer eine nuklearmedizinische Klinik ist ein Klinikinformationssystem (KIS) gekoppelt mit einem Radiologieinformationssystem (RIS) sowie einem Bildarchivierungs- und Verteilungssystem (PACS) unabdingbar, um einen schnellen Patientendurchsatz sowie die zeitnahe Uebermittlung von Befunden inklusive nuklearmedizinischen Bildern an zuweisende Stationen, Ambulanzen und externe Zuweiser zu gewaehrleisten. Daher wurde im April 2000 an der Klinik und Poliklinik fuer Nuklearmedizin der Universitaet

Introduction to Agronomy, Grain Crops, Weeds and Controls. A Learning Activity Pac in Agricultural Education Courses in Wisconsin.

Science.gov (United States)

Wisconsin State Dept. of Public Instruction, Madison. Div. of Instructional Services.

This learning activity pac contains information to help the teachers of high school vocational agriculture in the instructional area of agronomy. Each of the two main sections, grain crops and weeds and controls, includes teacher and student units for the section lessons. Teacher units include special instructions--equipment needed (film…

Minimally Clinically Important Change in the Activity Measure for Post-Acute Care (AM-PAC), a Generic Patient-Reported Outcome Tool, in People With Low Back Pain.

Science.gov (United States)

Lee, Natalie; Thompson, Nicolas R; Passek, Sandra; Stilphen, Mary; Katzan, Irene L

2017-11-01

The Activity Measure for Post-Acute Care (AM-PAC) is a generic metric of patient-reported functional status. The minimal clinically important difference (MCID) in the AM-PAC score has not been determined. The study objective was to determine the MCID for AM-PAC in people with low back pain. This was a retrospective cohort study. Anchor-based and distribution-based methods were used to estimate the MCID. The Modified Low Back Pain Disability Questionnaire was used as the anchor. Adults who had a primary ICD-9 code for low back pain in at least 1 outpatient physical therapist visit during an episode of care and who completed both the AM-PAC and the Modified Low Back Pain Disability Questionnaire in at least 2 visits during the care episode were included. The MCID was calculated for the AM-PAC basic mobility version as well its adapted version, which the Cleveland Clinic uses for patients 65 years old or older. A total of 1,271 participants were eligible for study. For the AM-PAC basic mobility version, anchor-based methods yielded MCID estimates of between 3.4 and 5.1, whereas distribution-based methods yielded estimates of 1.7 to 4.2. The minimal detectable change (MDC) for the AM-PAC basic mobility version was 3.3. For the adapted AM-PAC basic mobility version, the MCID was estimated to be between 2.9 and 4.0 via anchor-based methods and between 1.2 to 3.5 via distribution-based methods. The MDC for the adapted AM-PAC basic mobility version was 3.5. The estimated MCID was designed for people with low back pain only. The MCID ranged from 3.3 to 5.1 for the AM-PAC basic mobility version and 3.5 to 4 for the adapted version, with the MDC as the lower limit. Changes in the AM-PAC for people with low back pain may be interpreted using the estimated MCID. Future studies are needed to determine the AM-PAC MCID for populations other than those with low back pain. © 2017 American Physical Therapy Association

Actual concepts of digital PAC-spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Roeder, J., E-mail: j.roeder@tu-bs.de; Herden, C., E-mail: cherden@viewplus.de [Braunschweig University of Technology, Institute of Physical and Theoretical Chemistry (Germany); Gardner, J. A., E-mail: john.gardner@viewplus.com [Oregon State University (United States); Becker, K. D., E-mail: k-d.becker@tu-bs.de [Braunschweig University of Technology, Institute of Physical and Theoretical Chemistry (Germany); Uhrmacher, M., E-mail: muhrmac@gwdg.de; Hofsaess, H., E-mail: hhofsae@uni-goettingen.de [University of Goettingen, II. Institute of Physics (Germany)

2008-01-15

In conventional perturbed angular correlation (PAC)-spectroscopy huge amounts of events are processed by fast electronics. Modern digital signal processing devices and the improvement in the computer technology in recent years allow today digital PAC-spectrometer setups capable to perform software-based data processing with all the benefits of storage, repeatable data analysis under different limits, and easy switching between different isotopes. In this paper we discuss experiences and concepts of a first realized digital PAC-spectrometer, which will be rebuild at ISOLDE/CERN/Geneva.

Picture archiving and communications systems (PACS): an introduction

International Nuclear Information System (INIS)

Schwartz, L.H.

2001-01-01

Picture Archiving and Communications Systems (PACS) has revolutionized the practice of radiology. PACS consist of a variety of electronic/computer components, and the connectivity between these components. PACS is an efficient means to transmit, store, retrieve and digitally display medical images

PCaPAC 2006 Proceedings

Energy Technology Data Exchange (ETDEWEB)

Pavel Chevtsov; Matthew Bickley (Eds.)

2007-03-30

The 6-th international PCaPAC (Personal Computers and Particle Accelerator Controls) workshop was held at Jefferson Lab, Newport News, Virginia, from October 24-27, 2006. The main objectives of the conference were to discuss the most important issues of the use of PCs and modern IT technologies for controls of accelerators and to give scientists, engineers, and technicians a forum to exchange the ideas on control problems and their solutions. The workshop consisted of plenary sessions and poster sessions. No parallel sessions were held.Totally, more than seventy oral and poster presentations as well as tutorials were made during the conference, on the basis of which about fifty papers were submitted by the authors and included in this publication. This printed version of the PCaPAC 2006 Proceedings is published at Jefferson Lab according to the decision of the PCaPAC International Program Committee of October 26, 2006.

Integration of computer-aided diagnosis/detection (CAD) results in a PACS environment using CAD-PACS toolkit and DICOM SR

International Nuclear Information System (INIS)

Le, Anh H.T.; Liu, Brent; Huang, H.K.

2009-01-01

Picture Archiving and Communication System (PACS) is a mature technology in health care delivery for daily clinical imaging service and data management. Computer-aided detection and diagnosis (CAD) utilizes computer methods to obtain quantitative measurements from medical images and clinical information to assist clinicians to assess a patient's clinical state more objectively. CAD needs image input and related information from PACS to improve its accuracy; and PACS benefits from CAD results online and available at the PACS workstation as a second reader to assist physicians in the decision making process. Currently, these two technologies remain as two separate independent systems with only minimal system integration. This paper describes a universal method to integrate CAD results with PACS in its daily clinical environment. The method is based on Health Level 7 (HL7) and Digital imaging and communications in medicine (DICOM) standards, and Integrating the Healthcare Enterprise (IHE) workflow profiles. In addition, the integration method is Health Insurance Portability and Accountability Act (HIPAA) compliant. The paper presents (1) the clinical value and advantages of integrating CAD results in a PACS environment, (2) DICOM Structured Reporting formats and some important IHE workflow profiles utilized in the system integration, (3) the methodology using the CAD-PACS integration toolkit, and (4) clinical examples with step-by-step workflows of this integration. (orig.)

Role of pacs in an integrated communication system

International Nuclear Information System (INIS)

Thompson, B.G.; Creasy, J.L.; Johnston, R.E.; Parrish, D.; Scatliff, J.H.

1986-01-01

An integrated computer-based communications system uses multiple computers for the high speed transmission, storage, enhancement and display for medical information. Interconnected by a network such as coaxial and fiberoptic cables or microwave stations, the system would provide integrated communications throughout a satellite medical environment. As the availability of proven PACS components becomes a commercial reality, migratory expansion of PACS within the radiology clinical, educational and research areas will be possible. When the PACS is integrated with hospital, radiology and medical school information systems it provides the image component of a total medical information system. Current PACS efforts are on a research basis including the development of prototype systems. This paper provides an overview of implementation strategies. Issues to be discussed include PACS research objectives, typical implementation methods, and a review of interactions between PACS and radiology information systems (RIS) and hospital information systems

Tracking PACS usage with open source tools.

Science.gov (United States)

French, Todd L; Langer, Steve G

2011-08-01

A typical choice faced by Picture Archiving and Communication System (PACS) administrators is deciding how many PACS workstations are needed and where they should be sited. Oftentimes, the social consequences of having too few are severe enough to encourage oversupply and underutilization. This is costly, at best in terms of hardware and electricity, and at worst (depending on the PACS licensing and support model) in capital costs and maintenance fees. The PACS administrator needs tools to asses accurately the use to which her fleet is being subjected, and thus make informed choices before buying more workstations. Lacking a vended solution for this challenge, we developed our own.

PACS: implementation in the U.S. Department of Defense

Science.gov (United States)

Chacko, Anna K.; Wider, Ronald; Romlein, John R.; Cawthon, Michael A.; Richardson, Ronald R., Jr.; Lollar, H. William; Cook, Jay F.; Timboe, Harold L.; Johnson, Thomas G.; Fellows, Douglas W.

2000-05-01

The Department of Defense has been a leader in Radiology re- engineering for the past decade. Efforts have included the development of two landmark PACS specifications (MDIS and DIN- PACS), respective vendor selection and implementation programs. A Tri-Service (Army, Navy and Air Force) Radiology re-engineering program was initiated which identified transitioning to digital imaging, PACS and teleradiology as key enabling technologies in a changing business scenario. Subsequently, the systematic adjustment of procurement process for radiological imaging equipment included a focus on specifying PACS-capable-digital imaging modalities and mini- PACS as stepping stones to make the hospitals and health clinics PACS-ready. The success of the PACS and teleradiology program in the DOD is evidenced by the near filmless operation of most Army and Air Force Medical Centers, several community hospitals and several operational teleradiology constellations. Additionally, the MDIS PACSystem has become the commercial PACS product for General Electric Medical Systems. The DOD continues to forge ahead in the PACS arena by implementing advanced configurations and operational concepts such as the VRE (Virtual Radiology Environment), the negotiation of Regional Archiving and Regional PACS Maintenance Programs. Newer regulations (HIPAA, the FDA approval of digital mammography) have been promulgated impacting the culture and conduct of our business. Incorporating their requirements at the very outset will enable us to streamline the delivery of radiology. The DOD community has embraced the information age at multiple levels. The Healthcare portion of this community with these initiatives is integrating itself into DOD's future. The future holds great possibilities, promises and challenges for the DOD PACS programs.

Second-generation PACS

International Nuclear Information System (INIS)

Mattheus, R.; Osteaux, M.; Spruiyt, D.

1989-01-01

Purpose: In recent years, a gradual shift toward digital techniques has occurred in the field of medical imaging. The authors discuss how, with their approach, digital image management can be used in daily clinical routine. Instead of a centralized approach, we have taken a decentralized, multivendor, phase-expandable approach. The IMAC (image management and communication) architecture is a reflection of the organization of the imaging department. A section defined for each group of examinations (CT, MR imaging, DSA, emergency), has its own (dedicated) PACS environment, connected to the total PACS. Network management for controlling the image flow is based on patient appointments, scheduling of rooms, and work

PACS in the nuclear medicine service

International Nuclear Information System (INIS)

Bitter, F.; Hellwig, D.; Weller, R.; Almasi, L.; Adam, W.E.

1988-01-01

A Picture Archiving and Communication System (PACS) is to be understood as a central system in a hospital spanning all services, interconnecting all imaging stations and allowing digital picture archivation. All data of a patient are prepared for direct access. A PAC system is made up of the following components: imaging equipment and data systems, viewing stations (image display), picture communication, storage, archive, connection to hospital information system. The authors explain the requirements to be met by a PACS, its set-up and mode of function, and they system the use. (orig./MG) [de

Integration of a clinical trial database with a PACS

International Nuclear Information System (INIS)

Van Herk, M

2014-01-01

Many clinical trials use Electronic Case Report Forms (ECRF), e.g., from OpenClinica. Trial data is augmented if DICOM scans, dose cubes, etc. from the Picture Archiving and Communication System (PACS) are included for data mining. Unfortunately, there is as yet no structured way to collect DICOM objects in trial databases. In this paper, we obtain a tight integration of ECRF and PACS using open source software. Methods: DICOM identifiers for selected images/series/studies are stored in associated ECRF events (e.g., baseline) as follows: 1) JavaScript added to OpenClinica communicates using HTML with a gateway server inside the hospitals firewall; 2) On this gateway, an open source DICOM server runs scripts to query and select the data, returning anonymized identifiers; 3) The scripts then collects, anonymizes, zips and transmits selected data to a central trial server; 4) Here data is stored in a DICOM archive which allows authorized ECRF users to view and download the anonymous images associated with each event. Results: All integration scripts are open source. The PACS administrator configures the anonymization script and decides to use the gateway in passive (receiving) mode or in an active mode going out to the PACS to gather data. Our ECRF centric approach supports automatic data mining by iterating over the cases in the ECRF database, providing the identifiers to load images and the clinical data to correlate with image analysis results. Conclusions: Using open source software and web technology, a tight integration has been achieved between PACS and ECRF.

Deletion of pH Regulator pac-3 Affects Cellulase and Xylanase Activity during Sugarcane Bagasse Degradation by Neurospora crassa.

Directory of Open Access Journals (Sweden)

Amanda Cristina Campos Antoniêto

Full Text Available Microorganisms play a vital role in bioethanol production whose usage as fuel energy is increasing worldwide. The filamentous fungus Neurospora crassa synthesize and secrete the major enzymes involved in plant cell wall deconstruction. The production of cellulases and hemicellulases is known to be affected by the environmental pH; however, the regulatory mechanisms of this process are still poorly understood. In this study, we investigated the role of the pH regulator PAC-3 in N. crassa during their growth on sugarcane bagasse at different pH conditions. Our data indicate that secretion of cellulolytic enzymes is reduced in the mutant Δpac-3 at alkaline pH, whereas xylanases are positively regulated by PAC-3 in acidic (pH 5.0, neutral (pH 7.0, and alkaline (pH 10.0 medium. Gene expression profiles, evaluated by real-time qPCR, revealed that genes encoding cellulases and hemicellulases are also subject to PAC-3 control. Moreover, deletion of pac-3 affects the expression of transcription factor-encoding genes. Together, the results suggest that the regulation of holocellulase genes by PAC-3 can occur as directly as in indirect manner. Our study helps improve the understanding of holocellulolytic performance in response to PAC-3 and should thereby contribute to the better use of N. crassa in the biotechnology industry.

Fly ash: An alternative to powdered activated carbon for the removal of eosin dye from aqueous solutions

Directory of Open Access Journals (Sweden)

V.O. Njoku

2013-05-01

Full Text Available This paper reports the use of powdered activated carbon (PAC and raw coal fly ash (RFA in the removal of eosin dye from aqueous solution in batch processes. Operational parameters such as contact time, initial dye concentration, pH and temperature were investigated. Adsorption equilibrium was established in 120 min for the two adsorbents. Langmuir and Freundlich isotherms were used to fit the adsorption data. Langmuir model gave the best fit in both cases. The adsorption capacities of PAC and RFA were found to be 62.28 mg/g and 43.48 mg/g, respectively. The highest percentage of eosin dye removal for both PAC (98% and RFA (90% was observed at pH 2. Pseudo first-order and pseudo second-order kinetic models were used to fit the adsorption data. Pseudo second-order kinetic model gave the best description of the adsorption of eosin dye onto the two adsorbents. Thermodynamic parameters, ΔH0, ΔS0 and ΔG0 confirmed the physical nature, spontaneity and the endothermic nature of the adsorption process. A regeneration technique and a process calculation for evaluating the adsorbent dose required were carried out. This study has shown that RFA is a good alternative adsorbent in the removal of eosin dye from aqueous solution.

Reengineering the picture archiving and communication system (PACS) process for digital imaging networks PACS

OpenAIRE

Horton, Maria C.; Lewis, Thomas E.; Kinsey, Thomas V.

1999-01-01

Prior to June 1997, military picture archiving and communications systems (PACS) were planned, procured, and installed with key decisions on the system, equipment, and even funding sources made through a research and development office called Medical Diagnostic Imaging Systems (MDIS). Beginning in June 1997, the Joint Imaging Technology Project Office (JITPO) initiated a collaborative and consultative process for planning and implementing PACS into military treatment facilities through a new ...

Can PACS make a radiology department more competitive?

International Nuclear Information System (INIS)

Strickland, Nicola H.

1999-01-01

One of the motives for putting in a picture archiving and communication system (PACS) is to improve efficiency and hence enhance the competitive strength of the radiology department. Many would argue that it is now negligent to consider installing an old fashioned conventional radiology department rather than a PACS. In considering the issue it is important to be clear about the nature of the competition facing radiologists. This varies depending on the country and upon whether the institution is public or private. PACS can potentially help to overcome this competition in two ways: by providing real-time radiology, and by enabling teleradiology. Success in these areas requires state-of-the-art implementations of PACS, particularly clinically relevant PACS software, and adequate staffing levels

TiO2 Photocatalyst Nanoparticle Separation: Flocculation in Different Matrices and Use of Powdered Activated Carbon as a Precoat in Low-Cost Fabric Filtration

Directory of Open Access Journals (Sweden)

Carlos F. Liriano-Jorge

2014-01-01

Full Text Available Separation of photocatalyst nanoparticles is a problem impeding widespread application of photocatalytic oxidation. As sedimentation of photocatalyst particles is facilitated by their flocculation, the influence of common constituents of biologically pretreated wastewaters (NaCl, NaHCO3, and their combination with humic acid sodium salt on flocculation was tested by the pipet method. Results showed that the impact of these substances on TiO2 nanoparticle flocculation is rather complex and strongly affected by pH. When humic acid was present, TiO2 particles did not show efficient flocculation in the neutral and slightly basic pH range. As an alternative to photocatalyst separation by sedimentation, precoat vacuum filtration with powdered activated carbon (PAC over low-cost spunbond polypropylene fabrics was tested in the presence of two PAC types in aqueous NaCl and NaHCO3 solutions as well as in biologically treated greywater and in secondary municipal effluent. PAC concentrations of ≥2 g/L were required in order to achieve a retention of nearly 95% of the TiO2 nanoparticles on the fabric filter when TiO2 concentration was 1 g/L. Composition of the aqueous matrix and PAC type had a slight impact on precoat filtration. PAC precoat filtration represents a potential pretreatment for photocatalyst removal by micro- or ultrafiltration.

Metronidazole removal in powder-activated carbon and concrete-containing graphene adsorption systems: Estimation of kinetic, equilibrium and thermodynamic parameters and optimization of adsorption by a central composite design.

Science.gov (United States)

Manjunath, S V; Kumar, S Mathava; Ngo, Huu Hao; Guo, Wenshan

2017-12-06

Metronidazole (MNZ) removal by two adsorbents, i.e., concrete-containing graphene (CG) and powder-activated carbon (PAC), was investigated via batch-mode experiments and the outcomes were used to analyze the kinetics, equilibrium and thermodynamics of MNZ adsorption. MNZ sorption on CG and PAC has followed the pseudo-second-order kinetic model, and the thermodynamic parameters revealed that MNZ adsorption was spontaneous on PAC and non-spontaneous on CG. Subsequently, two-parameter isotherm models, i.e., Langmuir, Freundlich, Temkin, Dubinin-Radushkevich and Elovich models, were applied to evaluate the MNZ adsorption capacity. The maximum MNZ adsorption capacities ([Formula: see text]) of PAC and CG were found to be between 25.5-32.8 mg/g and 0.41-0.002 mg/g, respectively. Subsequently, the effects of pH, temperature and adsorbent dosage on MNZ adsorption were evaluated by a central composite design (CCD) approach. The CCD experiments have pointed out the complete removal of MNZ at a much lower PAC dosage by increasing the system temperature (i.e., from 20°C to 40°C). On the other hand, a desorption experiment has shown 3.5% and 1.7% MNZ removal from the surface of PAC and CG, respectively, which was insignificant compared to the sorbed MNZ on the surface by adsorption. The overall findings indicate that PAC and CG with higher graphene content could be useful in MNZ removal from aqueous systems.

IHE profiles applied to regional PACS

International Nuclear Information System (INIS)

Fernandez-Bayo, Josep

2011-01-01

PACS has been widely adopted as an image storage solution that perfectly fits the radiology department workflow and that can be easily extended to other hospital departments. Integrations with other hospital systems, like the Radiology Information System, the Hospital Information System and the Electronic Patient Record are fully achieved but still challenging aims. PACS also creates the perfect environment for teleradiology and teleworking setups. One step further is the regional PACS concept where different hospitals or health care enterprises share the images in an integrated Electronic Patient Record. Among the different solutions available to share images between different hospitals IHE (Integrating the Healthcare Enterprise) organization presents the Cross Enterprise Document Sharing profile (XDS) which allows sharing images from different hospitals even if they have different PACS vendors. Adopting XDS has multiple advantages, images do not need to be duplicated in a central archive to be shared among the different healthcare enterprises, they only need to be indexed and published in a central document registry. In the XDS profile IHE defines the mechanisms to publish and index the images in the central document registry. It also defines the mechanisms that each hospital will use to retrieve those images regardless on the Hospital PACS they are stored.

The HERSCHEL/PACS early Data Products

Science.gov (United States)

Wieprecht, E.; Wetzstein, M.; Huygen, R.; Vandenbussche, B.; De Meester, W.

2006-07-01

ESA's Herschel Space Observatory to be launched in 2007, is the first space observatory covering the full far-infrared and submillimeter wavelength range (60 - 670 microns). The Photodetector Array Camera & Spectrometer (PACS) is one of the three science instruments. It contains two Ge:Ga photoconductor arrays and two bolometer arrays to perform imaging line spectroscopy and imaging photometry in the 60 - 210 micron wavelength band. The HERSCHEL ground segment (Herschel Common Science System - HCSS) is implemented using JAVA technology and written in a common effort by the HERSCHEL Science Center and the three instrument teams. The PACS Common Software System (PCSS) is based on the HCSS and used for the online and offline analysis of PACS data. For telemetry bandwidth reasons PACS science data are partially processed on board, compressed, cut into telemetry packets and transmitted to the ground. These steps are instrument mode dependent. We will present the software model which allows to reverse the discrete on board processing steps and evaluate the data. After decompression and reconstruction the detector data and instrument status information are organized in two main PACS Products. The design of these JAVA classes considers the individual sampling rates, data formats, memory and performance optimization aspects and comfortable user interfaces.

Urological diagnosis using clinical PACS

Science.gov (United States)

Mills, Stephen F.; Spetz, Kevin S.; Dwyer, Samuel J., III

1995-05-01

Urological diagnosis using fluoroscopy images has traditionally been performed using radiographic films. Images are generally acquired in conjunction with the application of a contrast agent, processed to create analog films, and inspected to ensure satisfactory image quality prior to being provided to a radiologist for reading. In the case of errors the entire process must be repeated. In addition, the radiologist must then often go to a particular reading room, possibly in a remote part of the healthcare facility, to read the images. The integration of digital fluoroscopy modalities with clinical PACS has the potential to significantly improve the urological diagnosis process by providing high-speed access to images at a variety of locations within a healthcare facility without costly film processing. The PACS additionally provides a cost-effective and reliable means of long-term storage and allows several medical users to simultaneously view the same images at different locations. The installation of a digital data interface between the existing clinically operational PACS at the University of Virginia Health Sciences Center and a digital urology fluoroscope is described. Preliminary user interviews that have been conducted to determine the clinical effectiveness of PACS workstations for urological diagnosis are discussed. The specific suitability of the workstation medium is discussed, as are overall advantages and disadvantages of the hardcopy and softcopy media in terms of efficiency, timeliness and cost. Throughput metrics and some specific parameters of gray-scale viewing stations and the expected system impacts resulting from the integration of a urology fluoroscope with PACS are also discussed.

Investment alternative: the status quo or PACS?

Science.gov (United States)

Vanden Brink, John A.; Cywinski, Jozef K.

1990-08-01

While the cost of Picture Archiving and Communication Systems (PACS) can be substantial, the cost of continuing with present manual methods may become prohibitive in growing departments as the need for additional space and personnel (both technical and professional) to meet the increasing requirements for all image management activities continues to grow. This will occur simultaneously with increasing pressures on problems of the present system, i.e., lost films, lost revenues, delayed reporting and longer diagnostic cycle times. Present methods of image archiving communication and management i.e. the relationship of procedure volume to VFE requirements for professional and technical personnel, costs of film, film storage space, and other performance factors are analyzed based on the database created by the Technology Marketing Group (TMG) computerized cost analysis model applied to over 50 US hospitals. Also, the model is used to provide the projected cost of present methods of film management for an average US 400 +bed hospital based on ten year growth rate assumptions. TMG PACS Tracking data provides confirmation of staffmg pattern correlation to procedure volume. The data presented in the paper provides a basis for comparing the investment in maintaining the status quo to an investment in PACS.

PACS strategy for imaging centers.

Science.gov (United States)

Bedel, Victoria; Zdanowicz, Mark

2004-01-01

Picture archiving and communications systems (PACS) have been available in imaging centers for many years, but they often were less functional, were not well integrated into patient information systems, and lacked the network backbone to implement a system. As modalities are replaced and technology improves, the ability and time for an imaging center to acquire, integrate, and utilize PACS has arrived. However, each imaging center must determine why it should invest in PACS. A business plan is the fundamental need. Each imaging center must understand its target market, growth rate, and staffing plans. Additional considerations lie in current and future modality availability, the need for offsite delivery of images and reports, and the potential need for remote transmission of images. These issues must be identified and prioritized. A multidisciplinary team is essential. The most successful PACS implementation begins with complete involvement from all levels. The team should be comprised of people with complementary skills who are committed to a common purpose, set of performance goals, and approach for which they hold themselves mutually accountable. The team must jointly decide on the project's objectives. These objectives fall under 4 categories: clinical, service, financial, and performance. PACS must be considered a tool to help accomplish each objective. The imaging center must determine its top priorities, then translate them into a technology "wish list." The center can then list those pieces of technology that are most important and prioritize them. There are even more considerations for connecting multiple imaging centers. The team must create a comprehensive request for proposal (RFP) and determine the vendors that will receive the document. Once the RFP responses have been received and the vendor has been selected, an effective training plan must be executed. Training plans should be competency-based, ensuring comfort and competency among all staff. Upon

PACS influence the radiographer's work

International Nuclear Information System (INIS)

Fridell, Kent; Aspelin, Peter; Edgren, Lars; Lindskoeld, Lars; Lundberg, Nina

2009-01-01

Radiological departments are changing rapidly due to the implementation of digital images and PACS (Picture Archiving and Communication Systems). The introduction of new technology seems to dissolve boundaries between the professions in the work environment where the technology is introduced. This process tends to change the organization and its routines. The aim of this qualitative study is to explore changes in radiographers' work with regard to skills, work practice and technology. The study used open-ended interviews to explore the radiographers' perceptions of such changes, and to identify problems and solutions pertaining to work practice. Inspiration is taken from grounded theory to explain the changes in work that were found. Respondents were selected from a total of 133 potential participants as a theoretical or purposive sample. The changing trends within the professional role indicated that radiographers, as image producers, shifted their focus from the ability to set the optimal exposure parameters in order to obtain the optimal image for diagnosis to become expert in exposure parameters, projection techniques and diagnostic practice, having multifaceted skills, as being the jack of all trades. When implementing PACS there was an obvious change in image production. At the start there were visions of new routines, and therefore the radiographers became early adopters to the new technology; in practice the organization was stacked in old routines, as the routines were inflexible and PACS work was pushed into old work routines. Although inflexible, this does not mean that they cannot change, and obviously in 2006 new routines had been implemented making it possible for the radiographers in finding new ways for collaborating with colleagues. The new technology immediately created a vision of improved service to the clinicians. In order to optimize the service the radiographers developed an insight into the need for a more comprehensive change in work using

Removal of APIs and bacteria from hospital wastewater by MBR plus O(3), O(3) + H(2)O(2), PAC or ClO(2).

Science.gov (United States)

Nielsen, U; Hastrup, C; Klausen, M M; Pedersen, B M; Kristensen, G H; Jansen, J L C; Bak, S N; Tuerk, J

2013-01-01

The objective of this study has been to develop technologies that can reduce the content of active pharmaceutical ingredients (APIs) and bacteria from hospital wastewater. The results from the laboratory- and pilot-scale testings showed that efficient removal of the vast majority of APIs could be achieved by a membrane bioreactor (MBR) followed by ozone, ozone + hydrogen peroxide or powdered activated carbon (PAC). Chlorine dioxide (ClO(2)) was significantly less effective. MBR + PAC (450 mg/l) was the most efficient technology, while the most cost-efficient technology was MBR + ozone (156 mg O(3)/l applied over 20 min). With MBR an efficient removal of Escherichia coli and enterococci was measured, and no antibiotic resistant bacteria were detected in the effluent. With MBR + ozone and MBR + PAC also the measured effluent concentrations of APIs (e.g. ciprofloxacin, sulfamethoxazole and sulfamethizole) were below available predicted no-effect concentrations (PNEC) for the marine environment without dilution. Iodinated contrast media were also reduced significantly (80-99% for iohexol, iopromide and ioversol and 40-99% for amidotrizoateacid). A full-scale MBR treatment plant with ozone at a hospital with 900 beds is estimated to require an investment cost of €1.6 mill. and an operating cost of €1/m(3) of treated water.

Sorption of water alkalinity and hardness from high-strength wastewater on bifunctional activated carbon: process optimization, kinetics and equilibrium studies.

Science.gov (United States)

Amosa, Mutiu K

2016-08-01

Sorption optimization and mechanism of hardness and alkalinity on bifunctional empty fruit bunch-based powdered activation carbon (PAC) were studied. The PAC possessed both high surface area and ion-exchange properties, and it was utilized in the treatment of biotreated palm oil mill effluent. Batch adsorption experiments designed with Design Expert(®) were conducted in correlating the singular and interactive effects of the three adsorption parameters: PAC dosage, agitation speed and contact time. The sorption trends of the two contaminants were sequentially assessed through a full factorial design with three factor interaction models and a central composite design with polynomial models of quadratic order. Analysis of variance revealed the significant factors on each design response with very high R(2) values indicating good agreement between model and experimental values. The optimum operating conditions of the two contaminants differed due to their different regions of operating interests, thus necessitating the utility of desirability factor to get consolidated optimum operation conditions. The equilibrium data for alkalinity and hardness sorption were better represented by the Langmuir isotherm, while the pseudo-second-order kinetic model described the adsorption rates and behavior better. It was concluded that chemisorption contributed majorly to the adsorption process.

Making PACS the present, not the future.

Science.gov (United States)

Hunt, D

1998-01-01

Why haven't you moved forward with PACS? Have you just procrastinated or does your facility have legitimate reasons? Some say the technology is too confusing or too new, while others say the cost of PACS is too high. Many facilities say they haven't found a satisfactory way to deal with the conflicting opinions of their radiologists, IS department, administration, referring physicians and staff. Take time to compare the technology you do understand with something familiar such as your own PC or perhaps the current networks inside your facility. You'll soon begin to see that PACS is not a new technology, but rather a new methodology. To handle the perceived high cost of PACS, remember that every facility has different needs. Look at your work flow and then the many byproducts of PACS, such as marketing. If you are the first in your area to implement this new technology, you'll gain a marketing advantage in competing for referring physicians and managed care referral business. Follow the process you use to purchase other products, such as CT or MRI, as you investigate the vendors. Finally, make a plan! Determine departmental goals and gather information from vendors. Create a timeline, a financial plan and your marketing strategy. Together, these steps will help move PACS into the present for you.

Design and Implementation of PACS at Georgetown University Hospital

Science.gov (United States)

Mun, S. K.; Benson, H.. R.; Choyke, P.; Fahey, F. H.; Wang, P. C.; Zeman, R. K...; Elliott, L. P.

1985-09-01

During the preparation and planning phase of the PACS project at Georgetown University Hospital it was realized that PACS requires truly the state of the art technology in data communication, image processing and man machine interfacing. It was also realized that un-like many other technology intensive devices used in radiology, PACS cannot be seen as an independent system that will provide well defined services. PACS will be the backbone of the department operation in clinical, educational and managerial functions. It will indeed be the nerve center of the radiologic services affecting every aspect of the department. PACS will have to be designed to perform in a cost-effective manner to widely varying needs within the radiology departments. The integration of ever changing complex technology that will impact every aspect of a radiology service is not a trivial matter. This transition period going from current manual film based PACS to Digital PACS can be long, expansive and disruptive unless careful planning preceeds the implementation. PACS is still an emerging technology at its infancy. Performance monitoring and evaluation of diversified functions have to be also established so that improvement to the system can be efficiently implemented. Thus the evaluation criteria should be also established as early as possible.

Cloning and expression profiling of the PacSnRK2 and PacPP2C gene families during fruit development, ABA treatment, and dehydration stress in sweet cherry.

Science.gov (United States)

Shen, Xinjie; Guo, Xiao; Zhao, Di; Zhang, Qiang; Jiang, Yuzhuang; Wang, Yantao; Peng, Xiang; Wei, Yan; Zhai, Zefeng; Zhao, Wei; Li, Tianhong

2017-10-01

Plant SNF1-related protein kinase 2 (SnRK2) and protein phosphatase 2C (PP2C) family members are core components of the ABA signal transduction pathway. SnRK2 and PP2C proteins have been suggested to play crucial roles in fruit ripening and improving plant tolerance to drought stress, but supporting genetic information has been lacking in sweet cherry (Prunus avium L.). Here, we cloned six full-length SnRK2 genes and three full-length PP2C genes from sweet cherry cv. Hong Deng. Quantitative PCR analysis revealed that PacSnRK2.2, PacSnRK2.3, PacSnRK2.6, and PacPP2C1-3 were negatively regulated in fruits in response to exogenous ABA treatment, PacSnRK2.4 and PacSnRK2.5 were upregulated, and PacSnRK2.1 expression was not affected. The ABA treatment also significantly promoted the accumulation of anthocyanins in sweet cherry fruit. The expression of all PacSnRK2 and PacPP2C genes was induced by dehydration stress, which also promoted the accumulation of drought stress signaling molecules in the sweet cherry fruits, including ABA, soluble sugars, and anthocyanin. Furthermore, a yeast two-hybrid analysis demonstrated that PacPP2C1 interacts with all six PacSnRK2s, while PacPP2C3 does not interact with PacSnRK2.5. PacPP2C2 does not interact with PacSnRK2.1 or PacSnRK2.4. These results indicate that PacSnRK2s and PacPP2Cs may play a variety of roles in the sweet cherry ABA signaling pathway and the fruit response to drought stress. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

The effects of PACS on radiographer's work practice

International Nuclear Information System (INIS)

Larsson, W.; Aspelin, P.; Bergquist, M.; Hillergard, K.; Jacobsson, B.; Lindskoeld, L.; Wallberg, J.; Lundberg, N.

2007-01-01

This paper identifies and analyses the effects of picture archiving and communication systems (PACS) on radiographers' work practice. It shows that the introduction of PACS did not simply entail the transfer of data and information from the analogue world to the digital world, but it also led to the introduction of new ways of communicating, and new activities and responsibilities on the part of radiography staff. Radiographers are called upon to work increasingly independently, and individual practitioners require higher levels of professional expertise. In all, this paper demonstrates that new technical solutions sometimes lead to substantial changes in responsibilities in work. In this example, the radiographers' work practice has become more highly scientific and they are enjoying a higher level of prestige

Removal of a wide range of emerging pollutants from wastewater treatment plant discharges by micro-grain activated carbon in fluidized bed as tertiary treatment at large pilot scale

Energy Technology Data Exchange (ETDEWEB)

Mailler, R., E-mail: romain.mailler@siaap.fr [LEESU (UMR MA 102, Université Paris-Est, AgroParisTech), Université Paris-Est Créteil, 61 avenue du Général de Gaulle, 94010 Créteil Cedex (France); Gasperi, J., E-mail: gasperi@u-pec.fr [LEESU (UMR MA 102, Université Paris-Est, AgroParisTech), Université Paris-Est Créteil, 61 avenue du Général de Gaulle, 94010 Créteil Cedex (France); Coquet, Y. [SAUR, Direction de la Recherche et du Développement, 1 rue Antoine Lavoisier, 78064 Guyancourt (France); Buleté, A.; Vulliet, E. [Université de Lyon, Institut des Sciences Analytiques, UMR5280 CNRS, Université Lyon 1, ENS-Lyon, 5 rue de la Doua, 69100 Villeurbanne (France); Deshayes, S. [LEESU (UMR MA 102, Université Paris-Est, AgroParisTech), Université Paris-Est Créteil, 61 avenue du Général de Gaulle, 94010 Créteil Cedex (France); LCPP (Laboratoire Central de la Préfecture de Police), 39 bis rue de Dantzig, 75015 Paris (France); Zedek, S. [LEESU (UMR MA 102, Université Paris-Est, AgroParisTech), Université Paris-Est Créteil, 61 avenue du Général de Gaulle, 94010 Créteil Cedex (France); and others

2016-01-15

Among the solutions to reduce micropollutant discharges into the aquatic environment, activated carbon adsorption is a promising technique and a large scale pilot has been tested at the Seine Centre (240,000 m{sup 3}/d — Paris, France) wastewater treatment plant (WWTP). While most of available works studied fixed bed or contact reactors with a separated separation step, this study assesses a new type of tertiary treatment based on a fluidized bed containing a high mass of activated carbon, continuously renewed. For the first time in the literature, micro-grain activated carbon (μGAC) was studied. The aims were (1) to determine the performances of fluidized bed operating with μCAG on both emerging micropollutants and conventional wastewater quality parameters, and (2) to compare its efficiency and applicability to wastewater to former results obtained with PAC. Thus, conventional wastewater quality parameters (n = 11), pharmaceuticals and hormones (PPHs; n = 62) and other emerging pollutants (n = 57) have been monitored in μGAC configuration during 13 campaigns. A significant correlation has been established between dissolved organic carbon (DOC), PPHs and UV absorbance at 254 nm (UV-254) removals. This confirms that UV-254 could be used as a tertiary treatment performance indicator to monitor the process. This parameter allowed identifying that the removals of UV-254 and DOC reach a plateau from a μGAC retention time (SRT) of 90–100 days. The μGAC configuration substantially improves the overall quality of the WWTP discharges by reducing biological (38–45%) and chemical oxygen demands (21–48%), DOC (13–44%) and UV-254 (22–48%). In addition, total suspended solids (TSS) are retained by the μGAC bed and a biological activity (nitratation) leads to a total elimination of NO{sub 2}{sup −}. For micropollutants, PPHs have a good affinity for μGAC and high (> 60%) or very high (> 80%) removals are observed for most of the quantified compounds (n = 22

Removal of a wide range of emerging pollutants from wastewater treatment plant discharges by micro-grain activated carbon in fluidized bed as tertiary treatment at large pilot scale

International Nuclear Information System (INIS)

Mailler, R.; Gasperi, J.; Coquet, Y.; Buleté, A.; Vulliet, E.; Deshayes, S.; Zedek, S.

2016-01-01

Among the solutions to reduce micropollutant discharges into the aquatic environment, activated carbon adsorption is a promising technique and a large scale pilot has been tested at the Seine Centre (240,000 m"3/d — Paris, France) wastewater treatment plant (WWTP). While most of available works studied fixed bed or contact reactors with a separated separation step, this study assesses a new type of tertiary treatment based on a fluidized bed containing a high mass of activated carbon, continuously renewed. For the first time in the literature, micro-grain activated carbon (μGAC) was studied. The aims were (1) to determine the performances of fluidized bed operating with μCAG on both emerging micropollutants and conventional wastewater quality parameters, and (2) to compare its efficiency and applicability to wastewater to former results obtained with PAC. Thus, conventional wastewater quality parameters (n = 11), pharmaceuticals and hormones (PPHs; n = 62) and other emerging pollutants (n = 57) have been monitored in μGAC configuration during 13 campaigns. A significant correlation has been established between dissolved organic carbon (DOC), PPHs and UV absorbance at 254 nm (UV-254) removals. This confirms that UV-254 could be used as a tertiary treatment performance indicator to monitor the process. This parameter allowed identifying that the removals of UV-254 and DOC reach a plateau from a μGAC retention time (SRT) of 90–100 days. The μGAC configuration substantially improves the overall quality of the WWTP discharges by reducing biological (38–45%) and chemical oxygen demands (21–48%), DOC (13–44%) and UV-254 (22–48%). In addition, total suspended solids (TSS) are retained by the μGAC bed and a biological activity (nitratation) leads to a total elimination of NO_2"−. For micropollutants, PPHs have a good affinity for μGAC and high (> 60%) or very high (> 80%) removals are observed for most of the quantified compounds (n = 22/32), i

Benchmark test of CP-PACS for lattice QCD

International Nuclear Information System (INIS)

Yoshie, Tomoteru

1996-01-01

The CP-PACS is a massively parallel computer dedicated for calculations in computational physics and will be in operation in the spring of 1996 at Center for Computational Physics, University of Tsukuba. In this paper, we describe the architecture of the CP-PACS and report the results of the estimate of the performance of the CP-PACS for typical lattice QCD calculations. (author)

Performance evaluation of carbon nanotube enhanced membranes for SWRO pretreatment application

KAUST Repository

Lee, Jieun; Jeong, Sanghyun; Naidu, Gayathri; Ye, Yun; Chen, Vicki; Liu, Zongwen; Vigneswaran, Saravanamuthu

2016-01-01

organic matter improved to 66% with fewer amounts of powder activated carbon (PAC) (0.5 g/L) in MWCNT membrane filtration maintaining a high permeate flux of 600 LMH/bar. It was due to the increased porosity (84.5%) and hydrophilicity (52

PACS: Concepts and Trends

Science.gov (United States)

Bandon, David; Ratib, Osman; Lovis, Christian; Geissbuhler, Antoine

Picture Archiving and Communication Systems (PACS) are becoming part of the core components of today's infrastructure for digital radiology. In modern setting they also extend to the whole medical enterprise and integrate into the patient medical record. While local architectures may vary significantly, the major features such as image archiving and retrieval, workflow management, workstations and image acquisition and quality control systems constitute the key elements of such systems. PACS has also vocation to extend beyond the radiological images to become the common platform for hospital wide management of all images. The wireless access can contribute to expand the scope of image distribution.

Integrated RIS-PACS system

International Nuclear Information System (INIS)

Nishihara, Eitaro; Kura, Hiroyuki; Fukushima, Yuki

1994-01-01

We have developed an integrated RIS-PACS (radiology information system-picture archiving and communication system) system which supports examination, interpretation, and management in the diagnostic imaging department. The system was introduced in the Toshiba Hospital in May 1993, concurrently with the renewal of the hospital facilities. The integrated RIS-PACS system consists of a radiology information management system, and an image management system. The system supports wet (immediate) reading and chronological comparative reading using viewing workstation, enables routine operations to be performed in the diagnostic imaging department without film transportation, and contributes to the improvement of management efficiency in the department. (author)

PACS project management utilizing web-based tools

Science.gov (United States)

Patel, Sunil; Levin, Brad; Gac, Robert J., Jr.; Harding, Douglas, Jr.; Chacko, Anna K.; Radvany, Martin; Romlein, John R.

2000-05-01

As Picture Archiving and Communications Systems (PACS) implementations become more widespread, the management of deploying large, multi-facility PACS will become a more frequent occurrence. The tools and usability of the World Wide Web to disseminate project management information obviates time, distance, participant availability, and data format constraints, allowing for the effective collection and dissemination of PACS planning, implementation information, for a potentially limitless number of concurrent PACS sites. This paper will speak to tools, such as (1) a topic specific discussion board, (2) a 'restricted' Intranet, within a 'project' Intranet. We will also discuss project specific methods currently in use in a leading edge, regional PACS implementation concerning the sharing of project schedules, physical drawings, images of implementations, site-specific data, point of contacts lists, project milestones, and a general project overview. The individual benefits realized for the end user from each tool will also be covered. These details will be presented, balanced with a spotlight on communication as a critical component of any project management undertaking. Using today's technology, the web arguably provides the most cost and resource effective vehicle to facilitate the broad based, interactive sharing of project information.

Picture archiving and communication systems (PACS) for hospitals, a survey

International Nuclear Information System (INIS)

Haar Romeny, B.M. ter; Graaf, C.N. de; Waes, P.F.G.M. van; Rijk, P.P. van; Helder, J.C.; Valk, J.P.J. de

1985-01-01

In this article a survey is given for Picture Archiving and Communication Systems (PACS). Several aspects of PACS are treated, as image management, the introduction of the system, expenses etc. Special reference is made to the component parts of PACS: image stations, memory, network, software and coupling to the hospital information system. The introduction of PACS in Dutch hospitals is described. (Auth.)

Evaluation of a PACS workstation for interpreting body CT studies

International Nuclear Information System (INIS)

Franken, E.A.; Berbaum, K.S.; Honda, H.; McGuire, C.; Weis, R.R.; Barloon, T.

1989-01-01

This paper reports conventional hard-copy images from 266 body CT studies compared with those provided by a picture archiving and communication system (PACS) workstation. PACS images were evaluated before and after use of various image processing features. Most cases were depicted equally well, but in about one-fourth of the cases, diagnostic features were shown more clearly on PACS images. When PACS images were viewed first, a change in diagnosis after subsequent hardcopy inspection was infrequent, but when hard-copy images were viewed first, the results were converse. The image processing features of PACS were critical for its superior performance. The ability of a PACS to provide both image display and manipulation results in the superiority of that system

Clinical experience with PACS at Northwestern: year two

Science.gov (United States)

Channin, David S.; Hawkins, Rodney C.; Enzmann, Dieter R.

2001-08-01

We have previously described the PACS configuration at Northwestern Memorial Hospital (NMH). As opposed to an imaging modality, PACS is an evolving system that continuously grows and changes to meet the needs of the institution. The NMH PACS has grown significantly in the past year and has undergone significant architectural enhancements. This growth and evolutionary change will be described and discussed. The system now contains over 339,000 studies consisting of over 13 million images. There are now two short-term RAID storage units that provide for twice as much fast storage. There are also two magneto-optical disk jukeboxes providing long-term archive. We have deployed a redundant database to improve reliability of the system in the event of database failure. The number of modalities connected to the system has increased and will be summarized. Statistics describing utilization of the PACS will be shown. Lastly, we will discuss our plans for exploiting the application service provider model in our PACS environment.

Medical imaging, PACS, and imaging informatics: retrospective.

Science.gov (United States)

Huang, H K

2014-01-01

Historical reviews of PACS (picture archiving and communication system) and imaging informatics development from different points of view have been published in the past (Huang in Euro J Radiol 78:163-176, 2011; Lemke in Euro J Radiol 78:177-183, 2011; Inamura and Jong in Euro J Radiol 78:184-189, 2011). This retrospective attempts to look at the topic from a different angle by identifying certain basic medical imaging inventions in the 1960s and 1970s which had conceptually defined basic components of PACS guiding its course of development in the 1980s and 1990s, as well as subsequent imaging informatics research in the 2000s. In medical imaging, the emphasis was on the innovations at Georgetown University in Washington, DC, in the 1960s and 1970s. During the 1980s and 1990s, research and training support from US government agencies and public and private medical imaging manufacturers became available for training of young talents in biomedical physics and for developing the key components required for PACS development. In the 2000s, computer hardware and software as well as communication networks advanced by leaps and bounds, opening the door for medical imaging informatics to flourish. Because many key components required for the PACS operation were developed by the UCLA PACS Team and its collaborative partners in the 1980s, this presentation is centered on that aspect. During this period, substantial collaborative research efforts by many individual teams in the US and in Japan were highlighted. Credits are due particularly to the Pattern Recognition Laboratory at Georgetown University, and the computed radiography (CR) development at the Fuji Electric Corp. in collaboration with Stanford University in the 1970s; the Image Processing Laboratory at UCLA in the 1980s-1990s; as well as the early PACS development at the Hokkaido University, Sapporo, Japan, in the late 1970s, and film scanner and digital radiography developed by Konishiroku Photo Ind. Co. Ltd

The PAC-men revival : increasing need of PAC qualified colleagues

NARCIS (Netherlands)

Morren, J.; van der Heijden, S.

2012-01-01

More and more Protection, Automation, and Control (PAC) equipment is installed in the electricity (distribution) grid. For many employees of the network operators, the introduction of this equipment requires a change of mind, as this so-called secondary equipment is fundamentally different from the

Geometrical Acceptance Analysis for RPC PAC Trigger

CERN Document Server

Seo, Eunsung

2010-01-01

The CMS(Compact Muon Solenoid) is one of the four experiments that will analyze the collision results of the protons accelerated by the Large Hardron Collider(LHC) at CERN(Conseil Europen pour la Recherche Nuclaire). In case of the CMS experiment, the trigger system is divided into two stages : The Level-1 Trigger and High Level Trigger. The RPC(Resistive Plate Chamber) PAC(PAttern Comparator) Trigger system, which is a subject of this thesis, is a part of the Level-1 Muon Trigger System. Main task of the PAC Trigger is to identify muons, measures transverse momenta and select the best muon candidates for each proton bunch collision occurring every 25 ns. To calculate the value of PAC Trigger efficiency for triggerable muon, two terms of different efficiencies are needed ; acceptance efficiency and chamber efficiency. Main goal of the works described in this thesis is obtaining the acceptance efficiency of the PAC Trigger in each logical cone. Acceptance efficiency is a convolution of the chambers geometry an...

Process development and fabrication for sphere-pac fuel rods

International Nuclear Information System (INIS)

Welty, R.K.; Campbell, M.H.

1981-06-01

Uranium fuel rods containing sphere-pac fuel have been fabricated for in-reactor tests and demonstrations. A process for the development, qualification, and fabrication of acceptable sphere-pac fuel rods is described. Special equipment to control fuel contamination with moisture or air and the equipment layout needed for rod fabrication is described and tests for assuring the uniformity of the fuel column are discussed. Fuel retainers required for sphere-pac fuel column stability and instrumentation to measure fuel column smear density are described. Results of sphere-pac fuel rod fabrication campaigns are reviewed and recommended improvements for high throughput production are noted

[Economic and organizational evaluation of an imaging network (PACS)].

Science.gov (United States)

Charvet-Protat, S; Thoral, F

1998-12-01

Over the last twenty years, imaging modalities featuring new image production methods (ultrasound, nuclear magnetic resonance, etc.) have appeared on the market. Nevertheless, conventional radiology still accounts for 70% of the image examinations carried out in most western countries, including France. The conventional radiological image is in the process of evolving from analog to digital form. Digitalization of radiology means that image acquisition, archiving and distribution functions that were previously carried out by hand can now be automated using a Picture Archiving and Communication System. Decision-makers are having to decide whether or not to promote the development of PACS which, while they considerably modernize the way in which images are managed, also require heavy capital outlays. A critical appraisal of the literature allowed us to evaluate the relative cost and the efficiency of these image networks in comparison with film-based archiving and communication systems. It is clear from the economic evaluation that a PACS strategy involves greater costs than a film system. While PACS systems do generate savings on film and on storage space and obviate the need for certain staff, these savings do not offset the extra equipment and maintenance costs. This situation is likely to persist for some years yet, even when future price reductions are taken into account. The objective of this new radiological information management method is to improve organizational efficiency and hospital productivity. However, the economic evaluations that have been published to date are cost studies which do not take the efficiency criterion into account. A number of potential organizational benefits such as the fact that medical decisions can be made more quickly or that the average length of hospital stays can be reduced, are often claimed for PACS. However, for methodological reasons, these results cannot be generalised to cover all PACS. It is difficult to compare PACS

Status of the CP-PACS Project

International Nuclear Information System (INIS)

Ukawa, A.

1995-01-01

The CP-PACS Project, which started in April 1992, is a five-year plan to develop a massively parallel computer for carrying out research in computational physics with primary emphasis on lattice QCD. This article describes the architectural design of the CP-PACS computer, the entire computing system including the front end and mass storage, and results of benchmarks for the expected performance for lattice QCD applications. ((orig.))

Native oxy-PAHs, N-PACs, and PAHs in historically contaminated soils from Sweden, Belgium, and France: their soil-porewater partitioning behavior, bioaccumulation in Enchytraeus crypticus, and bioavailability.

Science.gov (United States)

Arp, Hans Peter H; Lundstedt, Staffan; Josefsson, Sarah; Cornelissen, Gerard; Enell, Anja; Allard, Ann-Sofie; Kleja, Dan Berggren

2014-10-07

Soil quality standards are based on partitioning and toxicity data for laboratory-spiked reference soils, instead of real world, historically contaminated soils, which would be more representative. Here 21 diverse historically contaminated soils from Sweden, Belgium, and France were obtained, and the soil-porewater partitioning along with the bioaccumulation in exposed worms (Enchytraeus crypticus) of native polycyclic aromatic compounds (PACs) were quantified. The native PACs investigated were polycyclic aromatic hydrocarbons (PAHs) and, for the first time to be included in such a study, oxygenated-PAHs (oxy-PAHs) and nitrogen containing heterocyclic PACs (N-PACs). The passive sampler polyoxymethylene (POM) was used to measure the equilibrium freely dissolved porewater concentration, Cpw, of all PACs. The obtained organic carbon normalized partitioning coefficients, KTOC, show that sorption of these native PACs is much stronger than observed in laboratory-spiked soils (typically by factors 10 to 100), which has been reported previously for PAHs but here for the first time for oxy-PAHs and N-PACs. A recently developed KTOC model for historically contaminated sediments predicted the 597 unique, native KTOC values in this study within a factor 30 for 100% of the data and a factor 3 for 58% of the data, without calibration. This model assumes that TOC in pyrogenic-impacted areas sorbs similarly to coal tar, rather than octanol as typically assumed. Black carbon (BC) inclusive partitioning models exhibited substantially poorer performance. Regarding bioaccumulation, Cpw combined with liposome-water partition coefficients corresponded better with measured worm lipid concentrations, Clipid (within a factor 10 for 85% of all PACs and soils), than Cpw combined with octanol-water partition coefficients (within a factor 10 for 76% of all PACs and soils). E. crypticus mortality and reproducibility were also quantified. No enhanced mortality was observed in the 21 historically

THE ZN-SITE IN BOVINE COPPER, ZINC SUPEROXIDE-DISMUTASE STUDIED BY CD-111 PAC

DEFF Research Database (Denmark)

Kofod, Pauli; Bjerrum, Morten J.; Bauer, Rogert

1991-01-01

The active site in bovine copper, zinc superoxide dismutase (Cu2. Zn2 SOD) has been studied by 111Cd time differential Perturbed Angular Correlation (PAC) on enzyme with Zn2+ replaced by excited 'Cd2+. The PAC spectra obtained for both the oxidized and the reduced form of Cu2Cd2SOD show...... no asymmetry between the two Zn-sites in the dimeric enzyme. The spectv further reveal that a significant change has taken place at the Zn-site in the reduced form compared to the oxidized form. Semi-empirical calculations based on the Angular Overlap Model (AOM) and coordinates from the crystal structure...... of the native enzyme are in agreement with the experimental PAC data of the oxidized enzyme. The results indicate that Cd2+ coordinates in the same manner as Zn2+ and that the crystal structure of SOD is valid for the enzyme in solution. The PAC spectrum of the reduced enzyme can be explained by extending...

IHE, Solution for integration of information systems and PACS

Directory of Open Access Journals (Sweden)

Milad Janghorban Lariche

2014-10-01

Full Text Available PACS is used as a way to store images and matches well with the workflow in the radiology department and can spread to other parts of hospital. Integration with other PACS and other hospital systems like radiology information system (RIS, hospital information system (HIS, and electronic patient records has been completely done, but there are still problems. PACS also provide good conditions for setting up Tele-radiology. The next step for PACS is where hospitals and health care organizations share photos in integrated electronic patient record. Among the different ways for sharing photos between different hospitals, IHE (integrating the health care enterprise standard indexes the cross-enterprise document sharing profile (XDS and allows sharing photos from various hospitals even if their PACS has different brands and different vendors. Application of XDS is useful for sharing images between health care organizations without duplicating them in a central archive. Images need to be indexed in a central registry. In the XDS profile, IHE defines an indexing mechanism for printing and indexing images in the central document registry. IHE also defines mechanisms to be used by each hospital to retrieve images, regardless of storing them in hospital PACS.

Fusion breeder sphere - PAC blanket design

International Nuclear Information System (INIS)

Sullivan, J.D.; Palmer, B.J.F.

1987-11-01

There is a considerable world-wide effort directed toward the production of materials for fusion reactors. Many ceramic fabrication groups are working on making lithium ceramics in a variety of forms, to be incorporated into the tritium breeding blanket which will surround the fusion reactor. Current blanket designs include ceramic in either monolithic or packed sphere bed (sphere-pac) forms. The major thrust at AECL is the production of lithium aluminate spheres to be incorporated in a sphere-pac bed. Contemporary studies on breeder blanket design offer little insight into the requirements on the sizes of the spheres. This study examined the parameters which determine the properties of pressure drop and coolant requirements. It was determined that an optimised sphere-pac bed would be composed of two diameters of spheres: 75 weight % at 3 mm and 25 weight % at 0.3 mm

Web based emergency room PACS

International Nuclear Information System (INIS)

Cha, Soon Joo; Cheon, Yong Kyung; Choi, Sung Woo Kim

2005-01-01

We wished to develop the web based Picture Archiving and Communication System in the emergency room for early decision making in emergency treatment planning at a full PACS Hospital. The program tools were Microsoft Visual Studio 6.0 - Visual C++ 6.0, and the Microsoft SQL 7.0 under the Microsoft Windows 2000 server operation system. The achievement of images was performed by an auto transport program installed in the ER and the radiology department. The average compression rates were 5:1 for CT and MR, and 20:1 for CR with JPEG 2000 lossy compression. All the images were stored on hard disk for 3 months. The patients' information was displayed for 2 weeks for reducing the security risk. For interdepartmental consultation, patient query by patient hospital number was available. Our Web based ER PACS could be useful system for early decision making for treatment planning in the emergency room because it reduces the risk factors for the security of the Web Paces by using a system independent from PACS in the hospital and minimizing the information patients

Web based emergency room PACS

Energy Technology Data Exchange (ETDEWEB)

Cha, Soon Joo; Cheon, Yong Kyung; Choi, Sung Woo Kim [Ilsan Paik Hospital, Inje University, Seoul (Korea, Republic of)] (and others)

2005-07-15

We wished to develop the web based Picture Archiving and Communication System in the emergency room for early decision making in emergency treatment planning at a full PACS Hospital. The program tools were Microsoft Visual Studio 6.0 - Visual C++ 6.0, and the Microsoft SQL 7.0 under the Microsoft Windows 2000 server operation system. The achievement of images was performed by an auto transport program installed in the ER and the radiology department. The average compression rates were 5:1 for CT and MR, and 20:1 for CR with JPEG 2000 lossy compression. All the images were stored on hard disk for 3 months. The patients' information was displayed for 2 weeks for reducing the security risk. For interdepartmental consultation, patient query by patient hospital number was available. Our Web based ER PACS could be useful system for early decision making for treatment planning in the emergency room because it reduces the risk factors for the security of the Web Paces by using a system independent from PACS in the hospital and minimizing the information patients.

Why PACS is no longer a four-letter word.

Science.gov (United States)

Chopra, R M

2000-01-01

The real value of PACS is not realized until widespread adoption exists among physicians other than interpreting radiologists. Referring physicians at the office level, in the operating room and in other departments must be willing to embrace the reading of images on monitors. That takes time. The payoff for a PACS system is therefore not realized until sometime in the future. Given the huge up-front capital expenditure required of PACS solutions, it is no wonder that the decision has historically been a difficult one to make. Enter the application service provider (ASP). The marriage of the ASP model to PACS seems to be one of the true "killer apps" currently available in the healthcare technology space. An ASP can host and maintain the software inherent in PACS solutions. Images are centrally archived over the short-, medium-, and long-term timeframe, utilizing state-of-art data management facilities. Some ASPs also provide the necessary bandwidth to office sites and the small amount of hardware that is required onsite, such as viewing stations or monitors. Costs for Internet-based image management under the ASP model rely on a pay-as-you-go formula, which may include all software, support, required hardware and bandwidth as part of the service. There may be a minor up-front fee for installation. The ASP pricing model eliminates the huge gamble an organization takes on "big iron" PACS purchases. Those benefits rely on the first rule of finance: a dollar today is worth more than a dollar tomorrow. PACS and ASPs were made for one another. Because the financial benefits of PACS are realized over time, the timing of cash flows is extremely important. Other benefits inherent in the ASP model such as scalability, diminished need for IT personnel, software version integrity and better pricing because of economies of scale are attractive also.

The future of PACS in healthcare enterprises

International Nuclear Information System (INIS)

Faggioni, Lorenzo; Neri, Emanuele; Castellana, Carlo; Caramella, Davide; Bartolozzi, Carlo

2011-01-01

Picture Archiving and Communication System (PACS), which was originally designed as a tool for facilitating radiologists in interpreting images more efficiently, is evolving into a hospital-integrated system storing diagnostic imaging information that often reaches far beyond Radiology. The continuous evolution of PACS technology has led to a gradual broadening of its applications, ranging from teleradiology to CAD (Computer-Assisted Diagnosis) and multidimensional imaging, and is moving into the direction of providing access to image data outside the Radiology department, so to reach all the branches of the healthcare enterprise. New perspectives have been created thanks to new technologies (such as holographic media and GRID computing) that are likely due to expand PACS-based applications even further, improving patient care and enhancing overall productivity.

Integration Of An MR Image Network Into A Clinical PACS

Science.gov (United States)

Ratib, Osman M.; Mankovich, Nicholas J.; Taira, Ricky K.; Cho, Paul S.; Huang, H. K.

1988-06-01

A direct link between a clinical pediatric PACS module and a FONAR MRI image network was implemented. The original MR network combines together the MR scanner, a remote viewing station and a central archiving station. The pediatric PACS directly connects to the archiving unit through an Ethernet TCP-IP network adhering to FONAR's protocol. The PACS communication software developed supports the transfer of patient studies and the patient information directly from the MR archive database to the pediatric PACS. In the first phase of our project we developed a package to transfer data between a VAX-111750 and the IBM PC I AT-based MR archive database through the Ethernet network. This system served as a model for PACS-to-modality network communication. Once testing was complete on this research network, the software and network hardware was moved to the clinical pediatric VAX for full PACS integration. In parallel to the direct transmission of digital images to the Pediatric PACS, a broadband communication system in video format was developed for real-time broadcasting of images originating from the MR console to 8 remote viewing stations distributed in the radiology department. These analog viewing stations allow the radiologists to directly monitor patient positioning and to select the scan levels during a patient examination from remote locations in the radiology department. This paper reports (1) the technical details of this implementation, (2) the merits of this network development scheme, and (3) the performance statistics of the network-to-PACS interface.

Project plan for PACS networking construction and cabling

International Nuclear Information System (INIS)

Luo Min; Wang Xiaolin; Luo Song; Lei Wenyong; Wang Xuejian; Wen Hongyue; Wu Hongxing

2002-01-01

Objective: To meet the networking requirement of the heave data flow, load balance, and potential networking storm during expanding the application of PACS. Methods: Intel Net Structure 480T Giga Switch was used as main switch and connected to each building by optical channel at 1 Giga speed to archive 100 MB/s to each port. At the same time, the in dependence of the original networking construction was physically kept. The layer 3 and 4 switchers was used as load balance to reduce the heavy load of the networking, and all the cabling for PACS used the super CAT5 along with the Intel Net Structure 1520 to prepare for the potential networking storm. Results: An advanced intranet was set up to fully meet the high standard requirement of PACS. The good foundation for upgrading the whole networking system to 1 Giga application was built for realized share and transmission of image, information, and patient data within the hospital. The base was established for the standardized management of the hospital. Conclusion: Good planning is the 1 st step in setting up PACS and the equipment are the platform to run PACS and all kinds of HIS. The networking construction is the foundation of e-hospitals

PACS in Töölö hospital.

Science.gov (United States)

Kinnunen, J; Pohjonen, H

2001-07-01

A 3-year PACS project was started in 1997 and completed in 1999 with filmless radiology and surgery. An efficient network for transferring images provides the infrastructure for integration of different distributed imaging systems and enables efficient handling of all patient-related information on one display station. Because of the need for high-speed communications and the massive amount of image data transferred in radiology, ATM (25, 155 Mbit/s) was chosen to be the main technology used. Both hardware and software redundancy of the system have been carefully planned. The size of the Dicom image library utilizing MO discs is currently 1.2 TB with 300 GB RAID capacity. For the increasing amount of teleradiologic consultations, a special Dicom gateway is planned. It allows a centralized and resilient handling and routing of received images around the hospital. Hospital-wide PACS has already improved the speed and quality of patient care by providing instant access to diagnostic information at multiple locations simultaneously. The benefits of PACS are considered from the viewpoint of the entire hospital: PACS offers a method for efficiently transporting patient-related images and reports to the referring physicians.

Design and optimizing factors of PACS network architecture

International Nuclear Information System (INIS)

Tao Yonghao; Miao Jingtao

2001-01-01

Objective: Exploring the design and optimizing factors of picture archiving and communication system (PACS) network architecture. Methods: Based on the PACS of shanghai first hospital to performed the measurements and tests on the requirements of network bandwidth and transmitting rate for different PACS functions and procedures respectively in static and dynamic network traffic situation, utilizing the network monitoring tools which built-in workstations and provided by Windows NT. Results: No obvious difference between switch equipment and HUB when measurements and tests implemented in static situation except route which slow down the rate markedly. In dynamic environment Switch is able to provide higher bandwidth utilizing than HUB and local system scope communication achieved faster transmitting rate than global system. Conclusion: The primary optimizing factors of PACS network architecture design include concise network topology and disassemble tremendous global traffic to multiple distributed local scope network communication to reduce the traffic of network backbone. The most important issue is guarantee essential bandwidth for diagnosis procedure of medical imaging

The sphere-PAC fuel code 'SPHERE-3'

International Nuclear Information System (INIS)

Wallin, H.

2000-01-01

Sphere-PAC fuel is an advanced nuclear fuel, in which the cladding tube is filled with small fuel spheres instead of the more usual fuel pellets. At PSI, the irradiation behaviour of sphere-PAC fuel is calculated using the computer code SPHERE-3. The paper describes the present status of the SPHERE-3 code, and some results of the qualification process against experimental data. (author)

The sphere-pac fuel code 'SPHERE-3'

International Nuclear Information System (INIS)

Wallin, H.; Nordstroem, L.A.; Hellwig, C.

2001-01-01

Sphere-pac fuel is an advanced nuclear fuel, in which the cladding tube is filled with small fuel spheres instead of the more usual fuel pellets. At PSI, the irradiation behaviour of sphere-pac fuel is calculated using the computer code SPHERE-3. The paper describes the present status of the SPHERE-3 code, and some results of the qualification process against experimental data. (author)

[PACS-based endoscope image acquisition workstation].

Science.gov (United States)

Liu, J B; Zhuang, T G

2001-01-01

A practical PACS-based Endoscope Image Acquisition Workstation is here introduced. By a Multimedia Video Card, the endoscope video is digitized and captured dynamically or statically into computer. This workstation realizes a variety of functions such as the endoscope video's acquisition and display, as well as the editing, processing, managing, storage, printing, communication of related information. Together with other medical image workstation, it can make up the image sources of PACS for hospitals. In addition, it can also act as an independent endoscopy diagnostic system.

PACS--and beyond. A journey to the digital promised land.

Science.gov (United States)

Viau, Mark A

2004-01-01

A successful picture archiving and communication system (PACS) integration depends on much more than the technology; marketing also plays a large role. This fact was evident from the inception of the PACS project at Boca Raton Community Hospital (BRCH). Strategic and effective marketing efforts should target technologists, nurses, physicians (including radiologists), administration, and colleagues in other departments. The buy-in of these users is critical to the project's success. BRCH's first marketing effort took place during the initial PACS presentation made to the hospital's board of directors. Once approval was given and a 6-month implementation target was set, a strategic and effective marketing/education plan commenced. Posters, brochures, t-shirts, and promotional items were distributed in a coordinated effort to target hospital staff and referring physician offices. Through its "Got PACS?" branding and other identity materials, BRCH implemented a marketing plan that informed, educated, and engaged PACS users.

HyPac french platform on the hydrogen and fuel cells; HyPac plateforme francaise sur l'hydrogene et les piles a combustible

Energy Technology Data Exchange (ETDEWEB)

Lucchese, P. [N ' ERGY, 85 - Antigny (France)

2008-07-01

HyPac is a french platform on the hydrogen and fuel cells applications, created in 2008. the authors presents the opportunities of the french platform HyPac, the objectives, the participants and the budget. (A.L.B.)

Pentachlorophenol reduction in raw Cauca river water through activated carbon adsorption in water purification

OpenAIRE

Camilo Hernán Cruz Vélez; Magally González; Héctor Mario Gutiérrez; Luz Edith Barba; Juan Carlos Escobar; Luis Germán Delgado; Patricia Torres

2008-01-01

Reducing chemical risk in raw water from the River Cauca (caused by the presence of pentachlorophenol and organic matter (real color, UV254 absorbance)) was evaluated at bench scale by using three treatment sequences: adsorption with powdered ac-tivated coal (PAC); adsorption – coagulation; and, adsorption – disinfection – coagulation. The results showed that although PAC is appropriate for pentachlorophenol removal, and its use together with the coagulant (aluminium sulphate) significantly i...

LANSCE personnel access control system (PACS)

International Nuclear Information System (INIS)

Sturrock, J.C.; Gallegos, F.R.; Hall, M.J.

1997-01-01

The Radiation Security System (RSS) at the Los Alamos Neutron Science Center (LANSCE) provides personnel protection from prompt radiation due to accelerated beam. The Personnel Access Control System (PACS) is a component of the RSS that is designed to prevent personnel access to areas where prompt radiation is a hazard. PACS was designed to replace several older personnel safety systems (PSS) with a single modem unified design. Lessons learned from the operation over the last 20 years were incorporated into a redundant sensor, single-point failure safe, fault tolerant, and tamper-resistant system that prevents access to the beam areas by controlling the access keys and beam stoppers. PACS uses a layered philosophy to the physical and electronic design. The most critical assemblies are battery backed up, relay logic circuits; less critical devices use Programmable Logic Controllers (PLCs) for timing functions and communications. Outside reviewers have reviewed the operational safety of the design. The design philosophy, lessons learned, hardware design, software design, operation, and limitations of the device are described

Incremental cost of PACS in a medical intensive care unit

Science.gov (United States)

Langlotz, Curtis P.; Cleff, Bridget; Even-Shoshan, Orit; Bozzo, Mary T.; Redfern, Regina O.; Brikman, Inna; Seshadri, Sridhar B.; Horii, Steven C.; Kundel, Harold L.

1995-05-01

Our purpose is to determine the incremental costs (or savings) due to the introduction of picture archiving and communication systems (PACS) and computed radiology (CR) in a medical intensive care unit (MICU). Our economic analysis consists of three measurement methods. The first method is an assessment of the direct costs to the radiology department, implemented in a spreadsheet model. The second method consists of a series of brief observational studies to measure potential changes in personnel costs that might not be reflected in administrative claims. The third method (results not reported here) is a multivariate modeling technique which estimates the independent effect of PACS/CR on the cost of care (estimated from administrative claims data), while controlling for clinical case- mix variables. Our direct cost model shows no cost savings to the radiology department after the introduction of PACS in the medical intensive care unit. Savings in film supplies and film library personnel are offset by increases in capital equipment costs and PACS operation personnel. The results of observational studies to date demonstrate significant savings in clinician film-search time, but no significant change in technologist time or lost films. Our model suggests that direct radiology costs will increase after the limited introduction of PACS/CR in the MICU. Our observational studies show a small but significant effect on clinician film search time by the introduction of PACS/CR in the MICU, but no significant effect on other variables. The projected costs of a hospital-wide PACS are currently under study.

[Sewage sludge conditioning by bioleaching-dual PAC and PAM addition].

Science.gov (United States)

Liu, Chang-Geng; Zhang, Pan-Yue; Zeng, Guang-Ming; Liu, Yong-Gang

2010-09-01

Bioleaching-dual polyaluminum chloride (PAC) and polyacrylamide (PAM) addition was used to condition sewage sludge. The results showed that FeSO4 x 7H2O addition improved the bioleaching rate obviously with a fixed sulfur power dosage of 3 g x L(-1); when the FeSO4 x 7H2O dosage was 8 g x L(-1), the bioleaching lasted 1.5 d to decrease the sludge pH below 2. Bioleaching improved the sludge dewaterability significantly with a specific resistance to filtration (SRF) reduction of 77.52% from 6.45 x 10(10)s2 x g(-10 to 1.45 x 10(10)s2 x g(-1), but the bioleached sludge was still difficult to be dewatered. After adjusting the bioleached sludge pH to 6, PAC and PAM were used to enhance conditioning of the bioleached sludge. The results indicated that the optimal dosage was 200 mg x L(-1) for PAC or 50 mg x L(-1) for PAM when single chemical was used. When PAC and PAM were dually used, the optimal dosages of PAC and PAM were 100 mg x L(-1) and 25 mg x L(-1), respectively; SRF and moisture of sludge cake reduced to 2.02 x 10(8) s2 x g(-1) and 74.81%, respectively, showing good dewaterability of the treated sludge. Compared with the single use of PAC and PAM, the dual use of PAC and PAM showed the advantages of lower cost and better conditioning effect.

La inserción al Asia-Pacífico, oportunidades y desafíos para el Valle del Cauca y la región pacífica colombiana

Directory of Open Access Journals (Sweden)

Ricardo Coutin

2014-12-01

Full Text Available Resumen: El objetivo general del texto es brindar una aproximación a los retos y las oportunidades que representa, para el Valle del Cauca y la Región Pacífica colombiana, la inserción al Asia-Pacífico. Para lo cual se plantean tres objetivos específicos: primero, analizar someramente el contexto económico comercial del Asia-Pacífico y América Latina, con especial énfasis en Colombia y los demás países de la Alianza del Pacífico (AP; segundo, estudiar las oportunidades y los retos para el Valle del Cauca y la Región Pacífica colombiana que plantea la puesta en escena del bloque comercial denominado Alianza del Pacífico; y tercero, indagar sobre los retos de competitividad y productividad que enfrenta el Valle del Cauca y que afectan el ambiente de negocios. El documento concluye que Colombia se encuentra rezagada en su inserción con la cuenca del Asia-Pacífico; también se plantea la necesidad de abordar el tema de estudio desde un enfoque subnacional.

A PACS archive architecture supported on cloud services.

Science.gov (United States)

Silva, Luís A Bastião; Costa, Carlos; Oliveira, José Luis

2012-05-01

Diagnostic imaging procedures have continuously increased over the last decade and this trend may continue in coming years, creating a great impact on storage and retrieval capabilities of current PACS. Moreover, many smaller centers do not have financial resources or requirements that justify the acquisition of a traditional infrastructure. Alternative solutions, such as cloud computing, may help address this emerging need. A tremendous amount of ubiquitous computational power, such as that provided by Google and Amazon, are used every day as a normal commodity. Taking advantage of this new paradigm, an architecture for a Cloud-based PACS archive that provides data privacy, integrity, and availability is proposed. The solution is independent from the cloud provider and the core modules were successfully instantiated in examples of two cloud computing providers. Operational metrics for several medical imaging modalities were tabulated and compared for Google Storage, Amazon S3, and LAN PACS. A PACS-as-a-Service archive that provides storage of medical studies using the Cloud was developed. The results show that the solution is robust and that it is possible to store, query, and retrieve all desired studies in a similar way as in a local PACS approach. Cloud computing is an emerging solution that promises high scalability of infrastructures, software, and applications, according to a "pay-as-you-go" business model. The presented architecture uses the cloud to setup medical data repositories and can have a significant impact on healthcare institutions by reducing IT infrastructures.

Java-based cryptosystem for PACS and tele-imaging

Science.gov (United States)

Tjandra, Donny; Wong, Stephen T. C.; Yu, Yuan-Pin

1998-07-01

Traditional PACS systems are based on two-tier client server architectures, and require the use of costly, high-end client workstations for image viewing. Consequently, PACS systems using the two-tier architecture do not scale well as data increases in size and complexity. Furthermore, use of dedicated viewing workstations incurs costs in deployment and maintenance. To address these issues, the use of digital library technologies, such as the World Wide Web, Java, and CORBA, is being explored to distribute PACS data to serve a broader range of healthcare providers in an economic and efficient manner. Integration of PACS systems with digital library technologies allows access to medical information through open networks such as the Internet. However, use of open networks to transmit medical data introduces problems with maintaining privacy and integrity of patient information. Cryptography and digital timestamping is used to protect sensitive information from unauthorized access or tampering. A major concern when using cryptography and digital timestamping is the performance degradation associated with the mathematical calculations needed to encrypt/decrypt an image dataset, or to calculate the hash value of an image. The performance issue is compounded by the extra layer associated with the CORBA middleware, and the use of programming languages interpreted at the client side, such as Java. This paper study the extent to which Java-based cryptography and digital timestamping affects performance in a PACS system integrated with digital library technologies.

Pentachlorophenol reduction in raw Cauca river water through activated carbon adsorption in water purification

Directory of Open Access Journals (Sweden)

Camilo Hernán Cruz Vélez

2008-09-01

Full Text Available Reducing chemical risk in raw water from the River Cauca (caused by the presence of pentachlorophenol and organic matter (real color, UV254 absorbance was evaluated at bench scale by using three treatment sequences: adsorption with powdered ac-tivated coal (PAC; adsorption – coagulation; and, adsorption – disinfection – coagulation. The results showed that although PAC is appropriate for pentachlorophenol removal, and its use together with the coagulant (aluminium sulphate significantly impro-ved phenolic compound and organic matter removal (promoting enhanced coagulation, the most efficient treatment sequence was adsorption – disinfection - coagulation, achieving minor pentachlorophenol levels than detection (1.56 μg/l and WHO li-mits (9μg/l due to the effect of chloride on PAC.

REVIEW ARTICLE REVI REVI Talking PACS: Part 1 – What is PACS?

African Journals Online (AJOL)

Image management is the administration of imaging examination requests, the performance of ... responsibility dependent on a long chain of human interaction that often fails. Within both ... This is an information system responsible for the storage, distribution .... This refers to a computer interface to gain access to the PACS.

Partners Against Crime (PAC) Districts

Data.gov (United States)

City and County of Durham, North Carolina — The Partners Against Crime (PAC) program promotes collaboration among police officers, Durham residents, and city and county government officials to find...

Removal of emerging contaminants by simultaneous application of membrane ultrafiltration, activated carbon adsorption, and ultrasound irradiation

International Nuclear Information System (INIS)

Secondes, Mona Freda N.; Naddeo, Vincenzo; Belgiorno, Vincenzo; Ballesteros, Florencio

2014-01-01

Highlights: • Above 99% of the emerging contaminants were removed in the USAMe process. • Influence of PAC dose and US frequency on removal is studied. • Improved performance is due to PAC adsorption enhancement and sonolytic degradation. • US irradiation improved efficiency and delayed declines in the removal of contaminants. • Performance of the hybrid process is better under lower frequency ultrasound irradiation. -- Abstract: Advanced wastewater treatment is necessary to effectively remove emerging contaminants (ECs) with chronic toxicity, endocrine disrupting effects, and the capability to induce the proliferation of highly resistant microbial strains in the environment from before wastewater disposal or reuse. This paper investigates the efficiency of a novel hybrid process that applies membrane ultrafiltration, activated carbon adsorption, and ultrasound irradiation simultaneously to remove ECs. Diclofenac, carbamazepine, and amoxicillin are chosen for this investigation because of their assessed significant environmental risks. Removal mechanisms and enhancement effects are analysed in single and combined processes. The influence of adsorbent dose and ultrasonic frequency to EC removal are also investigated. Results suggest that adsorption is probably the main removal mechanism and is affected by the nature of ECs and the presence of other components in the mixture. Almost complete removals are achieved in the hybrid process for all ECs

Removal of emerging contaminants by simultaneous application of membrane ultrafiltration, activated carbon adsorption, and ultrasound irradiation

Energy Technology Data Exchange (ETDEWEB)

Secondes, Mona Freda N. [Environmental Engineering Graduate Program, Department of Chemical Engineering, University of the Philippines – Diliman, Quezon City (Philippines); Naddeo, Vincenzo, E-mail: vnaddeo@unisa.it [Sanitary and Environmental Engineering Division (SEED), Department of Civil Engineering, University of Salerno, Fisciano 84084 (Saudi Arabia) (Italy); Belgiorno, Vincenzo [Sanitary and Environmental Engineering Division (SEED), Department of Civil Engineering, University of Salerno, Fisciano 84084 (Saudi Arabia) (Italy); Ballesteros, Florencio [Environmental Engineering Graduate Program, Department of Chemical Engineering, University of the Philippines – Diliman, Quezon City (Philippines)

2014-01-15

Highlights: • Above 99% of the emerging contaminants were removed in the USAMe process. • Influence of PAC dose and US frequency on removal is studied. • Improved performance is due to PAC adsorption enhancement and sonolytic degradation. • US irradiation improved efficiency and delayed declines in the removal of contaminants. • Performance of the hybrid process is better under lower frequency ultrasound irradiation. -- Abstract: Advanced wastewater treatment is necessary to effectively remove emerging contaminants (ECs) with chronic toxicity, endocrine disrupting effects, and the capability to induce the proliferation of highly resistant microbial strains in the environment from before wastewater disposal or reuse. This paper investigates the efficiency of a novel hybrid process that applies membrane ultrafiltration, activated carbon adsorption, and ultrasound irradiation simultaneously to remove ECs. Diclofenac, carbamazepine, and amoxicillin are chosen for this investigation because of their assessed significant environmental risks. Removal mechanisms and enhancement effects are analysed in single and combined processes. The influence of adsorbent dose and ultrasonic frequency to EC removal are also investigated. Results suggest that adsorption is probably the main removal mechanism and is affected by the nature of ECs and the presence of other components in the mixture. Almost complete removals are achieved in the hybrid process for all ECs.

Strengthening your ties to referring physicians through RIS/PACS integration.

Science.gov (United States)

Worthy, Susan; Rounds, Karla C; Soloway, Connie B

2003-01-01

Many imaging centers are turning to technology solutions to increase refering physician satisfaction, implementing such enhancements as automated report distribution, picture archiving and communications system (PACS), radiology information systems (RIS), and web-based results access. However, without seamless integration, these technology investments don't address the challenge at its core: convenient and reliable, two-way communication and interaction with referring physicians. In an integrated RIS/PACS solution, patient tracking in the RIS and PACS study status are logged and available to users. The time of the patient's registration at the imaging center, the exam start and completion time, the patient's departure time from the imaging center, and results status are all tracked and logged. An integrated RIS/PACS solution provides additional support to the radiologist, a critical factor that can improve the turnaround time of results to referring physicians. The RIS/PACS enhances the interpretation by providing the patient's history, which gives the radiologist additional insight and decreases the likelihood of missing a diagnostic element. In a tightly integrated RIS/PACS solution, results information is more complete. Physicians can view reports with associated images selected by the radiologist. They will also have full order information and complete imaging history including prior reports and images. Referring physicians can access and view images and exam notes at the same time that the radiologist is interpreting the exam. Without the benefit of an integrated RIS/PACS system, the referring physician would have to wait for the signed transcription to be released. In a seamlessly integrated solution, film-tracking modules within the RIS are fused with digital imaging workflow in the PACS. Users can see at a glance if a historical exam is available on film and benefit when a complete study history--both film-based and digital--is presented with the current

Performance characteristics of the Mayo/IBM PACS

Science.gov (United States)

Persons, Kenneth R.; Gehring, Dale G.; Pavicic, Mark J.; Ding, Yingjai

1991-07-01

The Mayo Clinic and IBM (at Rochester, Minnesota) have jointly developed a picture archiving system for use with Mayo's MRI and Neuro CT imaging modalities. The communications backbone of the PACS is a portion of the Mayo institutional network: a series of 4-Mbps token rings interconnected by bridges and fiber optic extensions. The performance characteristics of this system are important to understand because they affect the response time a PACS user can expect, and the response time for non-PACS users competing for resources on the institutional network. The performance characteristics of each component and the average load levels of the network were measured for various load distributions. These data were used to quantify the response characteristics of the existing system and to tune a model developed by North Dakota State University Department of Computer Science for predicting response times of more complex topologies.

Activated carbon from biomass

Science.gov (United States)

Manocha, S.; Manocha, L. M.; Joshi, Parth; Patel, Bhavesh; Dangi, Gaurav; Verma, Narendra

2013-06-01

Activated carbon are unique and versatile adsorbents having extended surface area, micro porous structure, universal adsorption effect, high adsorption capacity and high degree of surface reactivity. Activated carbons are synthesized from variety of materials. Most commonly used on a commercial scale are cellulosic based precursors such as peat, coal, lignite wood and coconut shell. Variation occurs in precursors in terms of structure and carbon content. Coir having very low bulk density and porous structure is found to be one of the valuable raw materials for the production of highly porous activated carbon and other important factor is its high carbon content. Exploration of good low cost and non conventional adsorbent may contribute to the sustainability of the environment and offer promising benefits for the commercial purpose in future. Carbonization of biomass was carried out in a horizontal muffle furnace. Both carbonization and activation were performed in inert nitrogen atmosphere in one step to enhance the surface area and to develop interconnecting porosity. The types of biomass as well as the activation conditions determine the properties and the yield of activated carbon. Activated carbon produced from biomass is cost effective as it is easily available as a waste biomass. Activated carbon produced by combination of chemical and physical activation has higher surface area of 2442 m2/gm compared to that produced by physical activation (1365 m2/gm).

[Study on influence between activated carbon property and immobilized biological activated carbon purification effect].

Science.gov (United States)

Wang, Guang-zhi; Li, Wei-guang; He, Wen-jie; Han, Hong-da; Ding, Chi; Ma, Xiao-na; Qu, Yan-ming

2006-10-01

By means of immobilizing five kinds of activated carbon, we studied the influence between the chief activated carbon property items and immobilized bioactivated carbon (IBAC) purification effect with the correlation analysis. The result shows that the activated carbon property items which the correlation coefficient is up 0.7 include molasses, abrasion number, hardness, tannin, uniform coefficient, mean particle diameter and effective particle diameter; the activated carbon property items which the correlation coefficient is up 0.5 include pH, iodine, butane and tetrachloride. In succession, the partial correlation analysis shows that activated carbon property items mostly influencing on IBAC purification effect include molasses, hardness, abrasion number, uniform coefficient, mean particle diameter and effective particle diameter. The causation of these property items bringing influence on IBAC purification is that the activated carbon holes distribution (representative activated carbon property item is molasses) provides inhabitable location and adjust food for the dominance bacteria; the mechanical resist-crash property of activated carbon (representative activated carbon property items: abrasion number and hardness) have influence on the stability of biofilm; and the particle diameter size and distribution of activated carbon (representative activated carbon property items: uniform coefficient, mean particle diameter and effective particle diameter) can directly affect the force of water in IBAC filter bed, which brings influence on the dominance bacteria immobilizing on activated carbon.

Enhanced removal of sulfonamide antibiotics by KOH-activated anthracite coal: Batch and fixed-bed studies.

Science.gov (United States)

Zuo, Linzi; Ai, Jing; Fu, Heyun; Chen, Wei; Zheng, Shourong; Xu, Zhaoyi; Zhu, Dongqiang

2016-04-01

The presence of sulfonamide antibiotics in aquatic environments poses potential risks to human health and ecosystems. In the present study, a highly porous activated carbon was prepared by KOH activation of an anthracite coal (Anth-KOH), and its adsorption properties toward two sulfonamides (sulfamethoxazole and sulfapyridine) and three smaller-sized monoaromatics (phenol, 4-nitrophenol and 1,3-dinitrobenzene) were examined in both batch and fixed-bed adsorption experiments to probe the interplay between adsorbate molecular size and adsorbent pore structure. A commercial powder microporous activated carbon (PAC) and a commercial mesoporous carbon (CMK-3) possessing distinct pore properties were included as comparative adsorbents. Among the three adsorbents Anth-KOH exhibited the largest adsorption capacities for all test adsorbates (especially the two sulfonamides) in both batch mode and fixed-bed mode. After being normalized by the adsorbent surface area, the batch adsorption isotherms of sulfonamides on PAC and Anth-KOH were displaced upward relative to the isotherms on CMK-3, likely due to the micropore-filling effect facilitated by the microporosity of adsorbents. In the fixed-bed mode, the surface area-normalized adsorption capacities of Anth-KOH for sulfonamides were close to that of CMK-3, and higher than that of PAC. The irregular, closed micropores of PAC might impede the diffusion of the relatively large-sized sulfonamide molecules and in turn led to lowered fixed-bed adsorption capacities. The overall superior adsorption of sulfonamides on Anth-KOH can be attributed to its large specific surface area (2514 m(2)/g), high pore volume (1.23 cm(3)/g) and large micropore sizes (centered at 2.0 nm). These findings imply that KOH-activated anthracite coal is a promising adsorbent for the removal of sulfonamide antibiotics from aqueous solution. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sizing a PACS

Science.gov (United States)

Wilson, Dennis L.; Glicksman, Robert A.

1994-05-01

A Picture Archiving and Communications System (PACS) must be able to support the image rate of the medical treatment facility. In addition the PACS must have adequate working storage and archive storage capacity required. The calculation of the number of images per minute and the capacity of working storage and of archiving storage is discussed. The calculation takes into account the distribution of images over the different size of radiological images, the distribution between inpatient and outpatient, and the distribution over plain film CR images and other modality images. The support of the indirect clinical image load is difficult to estimate and is considered in some detail. The result of the exercise for a particular hospital is an estimate of the average size of the images and exams on the system, of the number of gigabytes of working storage, of the number of images moved per minute, of the size of the archive in gigabytes, and of the number of images that are to be moved by the archive per minute. The types of storage required to support the image rates and the capacity required are discussed.

PAC Experiments at ISOLDE

CERN Multimedia

2002-01-01

The study of hyperfine interactions offers the possibility to use radioactive nuclei as probes in matter. The @g-@g perturbated angular correlation (PAC) technique following implantation has found widespread application in this field. At ISOLDE we have been investigating electric field gradients at impurities in non-cubic metals in an ongoing series of experiments. \\\\ \\\\ The small number of probe atoms necessary for these measurements make them also ideally suited for studies of surface problems like diffusion, structure and dynamics. Cd on a molybdenum O110? surface will be studied as first system. For this purpose 10|1|0~atoms of |1|1|1|mCd will be evaporated onto the clean surface and the electric field gradient for isolated adatoms on terrace sites will be determined by PAC. The UHV system constructed for such experiments at ISOLDE is shown in the schematic drawing. It is coupled to the beam line through differential pumping stations and contains standard surface treatment and analysis equipment.

PACS-Based Computer-Aided Detection and Diagnosis

Science.gov (United States)

Huang, H. K. (Bernie); Liu, Brent J.; Le, Anh HongTu; Documet, Jorge

The ultimate goal of Picture Archiving and Communication System (PACS)-based Computer-Aided Detection and Diagnosis (CAD) is to integrate CAD results into daily clinical practice so that it becomes a second reader to aid the radiologist's diagnosis. Integration of CAD and Hospital Information System (HIS), Radiology Information System (RIS) or PACS requires certain basic ingredients from Health Level 7 (HL7) standard for textual data, Digital Imaging and Communications in Medicine (DICOM) standard for images, and Integrating the Healthcare Enterprise (IHE) workflow profiles in order to comply with the Health Insurance Portability and Accountability Act (HIPAA) requirements to be a healthcare information system. Among the DICOM standards and IHE workflow profiles, DICOM Structured Reporting (DICOM-SR); and IHE Key Image Note (KIN), Simple Image and Numeric Report (SINR) and Post-processing Work Flow (PWF) are utilized in CAD-HIS/RIS/PACS integration. These topics with examples are presented in this chapter.

Enhanced removal of sulfonamide antibiotics by KOH-activated anthracite coal: Batch and fixed-bed studies

International Nuclear Information System (INIS)

Zuo, Linzi; Ai, Jing; Fu, Heyun; Chen, Wei; Zheng, Shourong; Xu, Zhaoyi; Zhu, Dongqiang

2016-01-01

The presence of sulfonamide antibiotics in aquatic environments poses potential risks to human health and ecosystems. In the present study, a highly porous activated carbon was prepared by KOH activation of an anthracite coal (Anth-KOH), and its adsorption properties toward two sulfonamides (sulfamethoxazole and sulfapyridine) and three smaller-sized monoaromatics (phenol, 4-nitrophenol and 1,3-dinitrobenzene) were examined in both batch and fixed-bed adsorption experiments to probe the interplay between adsorbate molecular size and adsorbent pore structure. A commercial powder microporous activated carbon (PAC) and a commercial mesoporous carbon (CMK-3) possessing distinct pore properties were included as comparative adsorbents. Among the three adsorbents Anth-KOH exhibited the largest adsorption capacities for all test adsorbates (especially the two sulfonamides) in both batch mode and fixed-bed mode. After being normalized by the adsorbent surface area, the batch adsorption isotherms of sulfonamides on PAC and Anth-KOH were displaced upward relative to the isotherms on CMK-3, likely due to the micropore-filling effect facilitated by the microporosity of adsorbents. In the fixed-bed mode, the surface area-normalized adsorption capacities of Anth-KOH for sulfonamides were close to that of CMK-3, and higher than that of PAC. The irregular, closed micropores of PAC might impede the diffusion of the relatively large-sized sulfonamide molecules and in turn led to lowered fixed-bed adsorption capacities. The overall superior adsorption of sulfonamides on Anth-KOH can be attributed to its large specific surface area (2514 m"2/g), high pore volume (1.23 cm"3/g) and large micropore sizes (centered at 2.0 nm). These findings imply that KOH-activated anthracite coal is a promising adsorbent for the removal of sulfonamide antibiotics from aqueous solution. - Highlights: • A high efficiency adsorbent for sulfonamide removal is prepared from anthracite. • Effects of

Role of transglutaminase 2 in PAC1 receptor mediated protection against hypoxia-induced cell death and neurite outgrowth in differentiating N2a neuroblastoma cells.

Science.gov (United States)

Algarni, Alanood S; Hargreaves, Alan J; Dickenson, John M

2017-03-15

The PAC 1 receptor and tissue transglutaminase (TG2) play important roles in neurite outgrowth and modulation of neuronal cell survival. In this study, we investigated the regulation of TG2 activity by the PAC 1 receptor in retinoic acid-induced differentiating N2a neuroblastoma cells. TG2 transamidase activity was determined using an amine incorporation and a peptide cross linking assay. In situ TG2 activity was assessed by visualising the incorporation of biotin-X-cadaverine using confocal microscopy. TG2 phosphorylation was monitored via immunoprecipitation and Western blotting. The role of TG2 in PAC 1 receptor-induced cytoprotection and neurite outgrowth was investigated by monitoring hypoxia-induced cell death and appearance of axonal-like processes, respectively. The amine incorporation and protein crosslinking activity of TG2 increased in a time and concentration-dependent manner following stimulation with pituitary adenylate cyclase-activating polypeptide-27 (PACAP-27). PACAP-27 mediated increases in TG2 activity were abolished by the TG2 inhibitors Z-DON and R283 and by pharmacological inhibition of protein kinase A (KT 5720 and Rp-cAMPs), protein kinase C (Ro 31-8220), MEK1/2 (PD 98059), and removal of extracellular Ca 2+ . Fluorescence microscopy demonstrated PACAP-27 induced in situ TG2 activity. TG2 inhibition blocked PACAP-27 induced attenuation of hypoxia-induced cell death and outgrowth of axon-like processes. TG2 activation and cytoprotection were also observed in human SH-SY5Y cells. Together, these results demonstrate that TG2 activity was stimulated downstream of the PAC 1 receptor via a multi protein kinase dependent pathway. Furthermore, PAC 1 receptor-induced cytoprotection and neurite outgrowth are dependent upon TG2. These results highlight the importance of TG2 in the cellular functions of the PAC 1 receptor. Copyright © 2017 Elsevier Inc. All rights reserved.

HyPac french platform on the hydrogen and fuel cells

International Nuclear Information System (INIS)

Lucchese, P.

2008-01-01

HyPac is a french platform on the hydrogen and fuel cells applications, created in 2008. the authors presents the opportunities of the french platform HyPac, the objectives, the participants and the budget. (A.L.B.)

PACS: Do clinical users benefit from it as a training adjunct?

Directory of Open Access Journals (Sweden)

J van Heerden

2011-05-01

Full Text Available Background. Over the past four years, Steve Biko Academic Hospital has been in the process of implementing and refining the use of a picture archiving and communications system (PACS. As part of a post-implementation refining process, it is necessary to evaluate user-perceptions in order to improve on good system qualities and correct flaws. Aim. The aim of this study was to assess whether medical clinicians perceived PACS as a positive adjunct to training and teaching opportunities – specifically those opportunities related to radiological image viewing and interpretation as part of patient case discussions. Method. Standardised questionnaires with ‘free text’ and ‘option selection’ questions were distributed to clinicians who, as part of their training, rotated at Steve Biko Academic Hospital (where a PACS is in place as well as other teaching hospitals without a PACS. Between February 2009 and May 2009, approximately 400 questionnaires were distributed. As a result of constant academic rotations, leave schedules of medical staff and posts vacated, questionnaires could not be distributed to the entire target population that was estimated to be in the region of 550 medical clinicians (comprising senior medical students, interns, medical officers, registrars and consultants. Of the 400 questionnaires distributed, 189 completed questionnaires were returned. Completion of the questionnaires was voluntary and anonymous. Results and conclusion. Although a PACS relates specifically to the archiving and retrieval of radiological images and reports, it became clear from the feedback received from medical clinicians (who are ward-based, theatre-based or clinic-based users of a digital system that many other factors, such as lack of adequate hardware and sub-optimal personal IT proficiency, contributed to some of the negative PACS-related perceptions and ‘lost teaching opportunities’ reported. Negative comments specifically related to PACS

Increasing Youth Physical Activity with Activity Calendars

Science.gov (United States)

Eckler, Seth

2016-01-01

Physical educators often struggle with ways to get their students to be active beyond the school day. One strategy to accomplish this is the use of physical activity calendars (PACs). The purpose of this article is to support the use of PACs and give practical advice for creating effective PACs.

The management and realizing of image data flow in PACS

International Nuclear Information System (INIS)

Tao Yonghao; Miao Jingtao

2002-01-01

Objective: To explore the management model and realizing of PACS image data-flow. Methods: Based on the implementing environment and management model of PACS image data-flow after full digital reengineering for radiology department in Shanghai First Hospital was completed, analysis on image data flow types, procedure, and achieving pattern were conducted. Results: Two kinds of image data-flow management were set up for the PACS of Shanghai First Hospital, which included image archiving procedure and image forward procedure. The former was implemented with central management model while the latter was achieved with a program that functionally acted as workflow management running on the central server. Conclusion: The image data-flow management pattern, as a key factor for PACS, has to be designed and implemented functionally and effectively depending on the performance environment, the tasks and requirements specified to particular user

A DICOM based PACS for nuclear medicine

International Nuclear Information System (INIS)

Lassmann, M.; Reiners, C.

2002-01-01

The installation of a radiology information system (RIS) connected to a hospital information system (HIS) and a picture archiving and communications system (PACS) seems mandatory for a nuclear medicine department in order to guarantee a high patient throughput. With these systems a fast transmission of reports, images to the in- and out-patients' wards and private practitioners is realized. Therefore, since April 2000, at the department of nuclear medicine of the university of Wuerzburg a completely DICOM based PACS has been implemented in addition to the RIS. With this system a DICOM based workflow is realized throughout the department of nuclear medicine for reporting and archiving. The PACS is connected to six gamma-cameras, a PET scanner, a bone densitometry system and an ultrasound device. The volume of image data archived per month is 4 GByte. Patient demographics are provided to the modalities via DICOM-Worklist. With these PACS components a department specific archive purely based on DICOM can be realized. During the installation process problems occurred mainly because of the complex DICOM standard for nuclear medicine. Related to that is the problem that most of the software implementations still contain bugs or are not adapted to the needs of a nuclear medicine department (particularly for PET). A communication software for the distribution of nuclear medicine reports and images based on techniques used for the worldwide web is currently tested. (orig.) [de

Activated carbons and gold

International Nuclear Information System (INIS)

McDougall, G.J.; Hancock, R.D.

1980-01-01

The literature on activated carbon is reviewed so as to provide a general background with respect to the effect of source material and activation procedure on carbon properties, the structure and chemical nature of the surface of the activated carbon, and the nature of absorption processes on carbon. The various theories on the absorption of gold and silver from cyanide solutions are then reviewed, followed by a discussion of processes for the recovery of gold and silver from cyanide solutions using activated carbon, including a comparison with zinc precipitation

La inserción al Asia-Pacífico, oportunidades y desafíos para el Valle del Cauca y la región pacífica colombiana

OpenAIRE

Ricardo Coutin

2014-01-01

Resumen: El objetivo general del texto es brindar una aproximación a los retos y las oportunidades que representa, para el Valle del Cauca y la Región Pacífica colombiana, la inserción al Asia-Pacífico. Para lo cual se plantean tres objetivos específicos: primero, analizar someramente el contexto económico comercial del Asia-Pacífico y América Latina, con especial énfasis en Colombia y los demás países de la Alianza del Pacífico (AP); segundo, estudiar las oportunidades y los retos para el Va...

La inserción al Asia-Pacífico, oportunidades y desafíos para el Valle del Cauca y la región pacífica colombiana

OpenAIRE

Countin, Ricardo

2014-01-01

El objetivo general del texto es brindar una aproximación a los retos y las oportunidades que representa, para el Valle del Cauca y la Región Pacífica colombiana, la inserción al Asia-Pacífico. Para lo cual se plantean tres objetivos específicos: primero, analizar someramente el contexto económico comercial del Asia-Pacífico y América Latina, con especial énfasis en Colombia y los demás países de la Alianza del Pacífico (AP); segundo, estudiar las oportunidades y los retos para el Valle del C...

THE REMOVAL OF GLYPHOSATE FROM DRINKING WATER

Science.gov (United States)

The effectiveness of granulated activated carbon (GAC), packed activated carbon (PAC), conventional treatment, membranes, and oxidation for removing glyphosate from natural waters is evaluated. Results indicate that GAC and PAC are not effective in removing glyphosate, while oxid...

Radiology department design to accommodate the future introduction of global PACS

International Nuclear Information System (INIS)

Naylor, A.F.

1992-01-01

In the light of the continuing development of pictorial archiving and communication systems (PACS) and image management and communications (MACS) systems it is appropriate to consider the provision that should be made in the design of a new or renovated department of radiology to accommodate these new technologies at either an earlier or later date. This paper considers 3 particular aspects of the influence of PACS on future department design: 1) the requirement for either more or less total department gross square feet, 2) the provision for the specific allocation of spaces at certain locations for PACS equipment and functions, and 3) the provision for dedicated pathways for fiber optic communications among the many locations in the department where PACS components would be located. (author). 1 fig

Does PACS improve diagnostic accuracy in chest radiograph interpretations in clinical practice?

International Nuclear Information System (INIS)

Hurlen, Petter; Borthne, Arne; Dahl, Fredrik A.; Østbye, Truls; Gulbrandsen, Pål

2012-01-01

Objectives: To assess the impact of a Picture Archiving and Communication System (PACS) on the diagnostic accuracy of the interpretation of chest radiology examinations in a “real life” radiology setting. Materials and methods: During a period before PACS was introduced to radiologists, when images were still interpreted on film and reported on paper, images and reports were also digitally stored in an image database. The same database was used after the PACS introduction. This provided a unique opportunity to conduct a blinded retrospective study, comparing sensitivity (the main outcome parameter) in the pre and post-PACS periods. We selected 56 digitally stored chest radiograph examinations that were originally read and reported on film, and 66 examinations that were read and reported on screen 2 years after the PACS introduction. Each examination was assigned a random number, and both reports and images were scored independently for pathological findings. The blinded retrospective score for the original reports were then compared with the score for the images (the gold standard). Results: Sensitivity was improved after the PACS introduction. When both certain and uncertain findings were included, this improvement was statistically significant. There were no other statistically significant changes. Conclusion: The result is consistent with prospective studies concluding that diagnostic accuracy is at least not reduced after PACS introduction. The sensitivity may even be improved.

Carbon activity meter

International Nuclear Information System (INIS)

Roy, P.; Krankota, J.L.

1975-01-01

A carbon activity meter utilizing an electrochemical carbon cell with gaseous reference electrodes having particular application for measuring carbon activity in liquid sodium for the LMFBR project is described. The electrolyte container is electroplated with a thin gold film on the inside surface thereof, and a reference electrode consisting of CO/CO 2 gas is used. (U.S.)

Activated, coal-based carbon foam

Science.gov (United States)

Rogers, Darren Kenneth; Plucinski, Janusz Wladyslaw

2004-12-21

An ablation resistant, monolithic, activated, carbon foam produced by the activation of a coal-based carbon foam through the action of carbon dioxide, ozone or some similar oxidative agent that pits and/or partially oxidizes the carbon foam skeleton, thereby significantly increasing its overall surface area and concurrently increasing its filtering ability. Such activated carbon foams are suitable for application in virtually all areas where particulate or gel form activated carbon materials have been used. Such an activated carbon foam can be fabricated, i.e. sawed, machined and otherwise shaped to fit virtually any required filtering location by simple insertion and without the need for handling the "dirty" and friable particulate activated carbon foam materials of the prior art.

Bioturbation and dissolved organic matter enhance contaminant fluxes from sediment treated with powdered and granular activated carbon.

Science.gov (United States)

Kupryianchyk, D; Noori, A; Rakowska, M I; Grotenhuis, J T C; Koelmans, A A

2013-05-21

Sediment amendment with activated carbon (AC) is a promising technique for in situ sediment remediation. To date it is not clear whether this technique sufficiently reduces sediment-to-water fluxes of sediment-bound hydrophobic organic chemicals (HOCs) in the presence of bioturbators. Here, we report polychlorobiphenyl (PCB) pore water concentrations, fluxes, mass transfer coefficients, and survival data of two benthic species, for four treatments: no AC addition (control), powdered AC addition, granular AC addition and addition and subsequent removal of GAC (sediment stripping). AC addition decreased mass fluxes but increased apparent mass transfer coefficients because of dissolved organic carbon (DOC) facilitated transport across the benthic boundary layer (BBL). In turn, DOC concentrations depended on bioturbator activity which was high for the PAC tolerant species Asellus aquaticus and low for AC sensitive species Lumbriculus variegatus. A dual BBL resistance model combining AC effects on gradients, DOC facilitated transport and biodiffusion was evaluated against the data and showed how the type of resistance differs with treatment and chemical hydrophobicity. Data and simulations illustrate the complex interplay between AC and contaminant toxicity to benthic organisms and how differences in species tolerance affect mass fluxes from sediment to the water column.

PAC and μSr investigations of light interstitial diffusion in intermetallic hydrides

International Nuclear Information System (INIS)

Boyer, P.; Baudry, A.

1988-01-01

Specific aspects of the Perturbed Angular Correlation (PAC) of gamma rays concerning its application to the study of atomic diffusion in solids are presented. PAC results recently obtained on the 181 Ta probe in several crystalline and amorphous phases of Zr 2 Ni hydrides are briefly summarized. Preliminary μSR results relative to these intermetallic hydrides are presented and compared to the PAC data

Acquisition and analysis of throughput rates for an operational department-wide PACS

Science.gov (United States)

Stewart, Brent K.; Taira, Ricky K.; Dwyer, Samuel J., III; Huang, H. K.

1992-07-01

The accurate prediction of image throughput is a critical issue in planning for and acquisition of any successful Picture Archiving and Communication System (PACS). Bottlenecks or design flaws can render an expensive PACS implementation useless. This manuscript presents a method for accurately predicting and measuring image throughput of a PACS design. To create the simulation model of the planned or implemented PACS, it must first be decomposed into principal tasks. We have decomposed the entire PACS image management chain into eight subsystems. These subsystems include network transfers over three different networks (Ethernet, FDDI and UltraNet) and five software programs and/or queues: (1) transfer of image data from the imaging modality computer to the image acquisition/reformatting computer; (2) reformatting the image data into a standard image format; (3) transferring the image data from the acquisition/reformatting computer to the image archive computer; (4) updating a relational database management system over the network; (5) image processing-- rotation and optimal gray-scale lookup table calculation; (6) request that the image be archived; (7) image transfer from the image archive computer to a designated image display workstation; and (8) update the local database on the image display station, separate the image header from the image data and store the image data on a parallel disk array. Through development of an event logging facility and implementation of a network management package we have acquired throughput data for each subsystem in the PACS chain. In addition, from our PACS relational database management system, we have distilled the traffic generation patterns (temporal, file size and destination) of our imaging modality devices. This data has been input into a simulation modeling package (Block Oriented Network Simulator-- BONeS) to estimate the characteristics of the modeled PACS, e.g., the throughput rates and delay time. This simulation

Scientific programming on massively parallel processor CP-PACS

International Nuclear Information System (INIS)

Boku, Taisuke

1998-01-01

The massively parallel processor CP-PACS takes various problems of calculation physics as the object, and it has been designed so that its architecture has been devised to do various numerical processings. In this report, the outline of the CP-PACS and the example of programming in the Kernel CG benchmark in NAS Parallel Benchmarks, version 1, are shown, and the pseudo vector processing mechanism and the parallel processing tuning of scientific and technical computation utilizing the three-dimensional hyper crossbar net, which are two great features of the architecture of the CP-PACS are described. As for the CP-PACS, the PUs based on RISC processor and added with pseudo vector processor are used. Pseudo vector processing is realized as the loop processing by scalar command. The features of the connection net of PUs are explained. The algorithm of the NPB version 1 Kernel CG is shown. The part that takes the time for processing most in the main loop is the product of matrix and vector (matvec), and the parallel processing of the matvec is explained. The time for the computation by the CPU is determined. As the evaluation of the performance, the evaluation of the time for execution, the short vector processing of pseudo vector processor based on slide window, and the comparison with other parallel computers are reported. (K.I.)

Activated carbon material

International Nuclear Information System (INIS)

Evans, A.G.

1978-01-01

Activated carbon particles for use as iodine trapping material are impregnated with a mixture of selected iodine and potassium compounds to improve the iodine retention properties of the carbon. The I/K ratio is maintained at less than about 1 and the pH is maintained at above about 8.0. The iodine retention of activated carbon previously treated with or coimpregnated with triethylenediamine can also be improved by this technique. Suitable flame retardants can be added to raise the ignition temperature of the carbon to acceptable standards

Introduction to PAC-experiments and hyperfine interaction measurements in solids

International Nuclear Information System (INIS)

Manasijevic, M.; Koicki, S.; Cekic, B.; Ivanovic, N.; Milosevic, Z.; Koteski, V.; Radisavljevic, I.; Cavor, J.; Marjanovic, D.

2001-01-01

Perturbed angular correlation (PAC) has for many years been a productive experimental technique for obtaining information about the static and dynamic behaviour of local and electronic structures of solids on a microscope scale, without changing the main properties of the material. This article contains an outline of the basic principles of PAC. A summary of the technique and experimental requirements is given, followed by a brief discussion of the parameters which can be extracted from the PAC measurements. Some examples then illustrate the recent developments in the applications to problems of interest for solid state physics nad materials science, performed in VINCA Institute. (author)

The sphere-PAC fuel code 'SPHERE-3'

Energy Technology Data Exchange (ETDEWEB)

Wallin, H

2000-07-01

Sphere-PAC fuel is an advanced nuclear fuel, in which the cladding tube is filled with small fuel spheres instead of the more usual fuel pellets. At PSI, the irradiation behaviour of sphere-PAC fuel is calculated using the computer code SPHERE-3. The paper describes the present status of the SPHERE-3 code, and some results of the qualification process against experimental data. (author)

Implementation of MINI-PACS using the DICOM converter on the Web

International Nuclear Information System (INIS)

Ji, Youn Sang

2000-01-01

In recent years, medical procedures have become more complex, while financial pressures for shortened hospital stays and increased efficiency in patient care have increased. As a result, several shortcomings of present film-based systems for managing medical images have become apparent. Maintaining film space is labor intensive and consumes valuable space. Because only single copies of radiological examinations exist, they are prone to being lost or misplaced, thereby consuming additional valuable time and expense. In this paper, MINI-PACS for image archiving, transmission, and viewing offers a solution to these problems. Proposed MINI-PACS consists of mainly four parts such as Web Module, Client-Server Module, Internal Module, Acquisition Module. In addition, MINI-PACS system includes DICOM Converter that Non-DICOM file format converts standard file format. In Client-Server Module case, Proposed system is combined both SCU(Service Class User: Client) part and SCP(Service Class Provider: Server) part therefore this system provides the high resolution image processing techniques based on windows platform. Because general PACS system is too expensive for Medium and Small hospitals to install and operate the full-PACS. Also, we constructed Web Module for database connection through the WWW.=20

75 FR 80082 - State, Local, Tribal, And Private Sector Policy Advisory Committee (SLTPS-PAC)

Science.gov (United States)

2010-12-21

..., Tribal, And Private Sector Policy Advisory Committee (SLTPS-PAC) AGENCY: Information Security Oversight... State, Local, Tribal, and Private Sector Policy Advisory Committee (SLTPS-PAC). The SLTPS-PAC will..., Tribal, and Private Sector Entities, as specified in Executive Order 13549 and its implementing directive...

Bioavailability of {sup 99m}Tc-paclitaxel-glucuronide ({sup 99m}Tc-PAC-G)

Energy Technology Data Exchange (ETDEWEB)

Biber Muftuler, F.Z.; Demir, I.; Uenack, P.; Ichedef, C.; Yurt Kilcar, A. [Ege Univ., Izmir (Turkey). Dept. of Nuclear Applications

2011-07-01

An antitumor agent paclitaxel (PAC) has been proved to be efficient in the treatment of breast and ovarian cancer. Glucuronic acid-derived paclitaxel compound (paclitaxel-glucuronide (PAC-G)) was enzymatically synthesized using microsome preparate separated from rat livers. The biodistribution mechanism of PAC-G in healthy female Albino Wistar rats has been investigated. The expected structure is confirmed according to LC/MS results, and the possible attachment is to C2-hydroxyl group. PAC-G was labeled with {sup 99m}Tc and the radiochemical yield of radiolabeled compound ({sup 99m}Tc-PAC-G) was 98.0 {+-} 02.74% (n=9). The range of the breast/blood and breast/muscle ratios is approximately between 3 and 35 in 240 min. All these experimental studies indicate that {sup 99m}Tc-PAC-G may potentially be used in breast tissue as an imaging agent. (orig.)

PACS/IMAC technology assessment

OpenAIRE

Schilling, Ronald B.

1997-01-01

According to Peter Ogle of Digital Imaging (San Francisco, CA), “Radiologists should help identify common values for the use of information technology in medicine.” Achieving a set of common values often requires a framework for organizing the thought process involved. That is the focus of this article in addressing the subject of picture archiving and communication system (PACS) technology assessment.

Implementation, reliability, and feasibility test of an Open-Source PACS.

Science.gov (United States)

Valeri, Gianluca; Zuccaccia, Matteo; Badaloni, Andrea; Ciriaci, Damiano; La Riccia, Luigi; Mazzoni, Giovanni; Maggi, Stefania; Giovagnoni, Andrea

2015-12-01

To implement a hardware and software system able to perform the major functions of an Open-Source PACS, and to analyze it in a simulated real-world environment. A small home network was implemented, and the Open-Source operating system Ubuntu 11.10 was installed in a laptop containing the Dcm4chee suite with the software devices needed. The Open-Source PACS implemented is compatible with Linux OS, Microsoft OS, and Mac OS X; furthermore, it was used with operating systems that guarantee the operation in portable devices (smartphone, tablet) Android and iOS. An OSS PACS is useful for making tutorials and workshops on post-processing techniques for educational and training purposes.

From PACS to Web-based ePR system with image distribution for enterprise-level filmless healthcare delivery.

Science.gov (United States)

Huang, H K

2011-07-01

The concept of PACS (picture archiving and communication system) was initiated in 1982 during the SPIE medical imaging conference in New Port Beach, CA. Since then PACS has been matured to become an everyday clinical tool for image archiving, communication, display, and review. This paper follows the continuous development of PACS technology including Web-based PACS, PACS and ePR (electronic patient record), enterprise PACS to ePR with image distribution (ID). The concept of large-scale Web-based enterprise PACS and ePR with image distribution is presented along with its implementation, clinical deployment, and operation. The Hong Kong Hospital Authority's (HKHA) integration of its home-grown clinical management system (CMS) with PACS and ePR with image distribution is used as a case study. The current concept and design criteria of the HKHA enterprise integration of the CMS, PACS, and ePR-ID for filmless healthcare delivery are discussed, followed by its work-in-progress and current status.

PACS 2000: quality control using the task allocation chart

Science.gov (United States)

Norton, Gary S.; Romlein, John R.; Lyche, David K.; Richardson, Ronald R., Jr.

2000-05-01

Medical imaging's technological evolution in the next century will continue to include Picture Archive and Communication Systems (PACS) and teleradiology. It is difficult to predict radiology's future in the new millennium with both computed radiography and direct digital capture competing as the primary image acquisition methods for routine radiography. Changes in Computed Axial Tomography (CT) and Magnetic Resonance Imaging (MRI) continue to amaze the healthcare community. No matter how the acquisition, display, and archive functions change, Quality Control (QC) of the radiographic imaging chain will remain an important step in the imaging process. The Task Allocation Chart (TAC) is a tool that can be used in a medical facility's QC process to indicate the testing responsibilities of the image stakeholders and the medical informatics department. The TAC shows a grid of equipment to be serviced, tasks to be performed, and the organization assigned to perform each task. Additionally, skills, tasks, time, and references for each task can be provided. QC of the PACS must be stressed as a primary element of a PACS' implementation. The TAC can be used to clarify responsibilities during warranty and paid maintenance periods. Establishing a TAC a part of a PACS implementation has a positive affect on patient care and clinical acceptance.

PACS and diagnostic imaging service delivery-A UK perspective

International Nuclear Information System (INIS)

Sutton, Laurence N.

2011-01-01

This review sets out the current position with regard to the implementation of PACS throughout the United Kingdom and the impact this has had on improving patient care. In December 2007 England had implemented full hospital-wide PACS in all hospitals: a major achievement in the relatively short time period of three years. The different approaches used by each country of the UK to achieve full national PACS are described in addition to the current issues with the sharing of images and reports across different healthcare organisations with regard to technical solutions, clinical safety and governance. The review gives insight into the changing methods of service delivery to address increasing demand pressures on diagnostic imaging services and how the national PACS implementation, specifically in England, has made a significant contribution to measures to improve efficiencies. The role of Teleradiology is discussed in the context of supporting local patient services rather than undermining them and the concept of cross-healthcare reporting 'Grids' is described. Finally, in the summary it is recognised that the vast wealth of knowledge accumulated during the national implementations has placed the UK in a strong position to facilitate full national data sharing across all healthcare organisations to improve patient care.

The Protective Role of PAC1-Receptor Agonist Maxadilan in BCCAO-Induced Retinal Degeneration.

Science.gov (United States)

Vaczy, A; Reglodi, D; Somoskeoy, T; Kovacs, K; Lokos, E; Szabo, E; Tamas, A; Atlasz, T

2016-10-01

A number of studies have proven that pituitary adenylate cyclase activating polypeptide (PACAP) is protective in neurodegenerative diseases. Permanent bilateral common carotid artery occlusion (BCCAO) causes severe degeneration in the rat retina. In our previous studies, protective effects were observed with PACAP1-38, PACAP1-27, and VIP but not with their related peptides, glucagon, or secretin in BCCAO. All three PACAP receptors (PAC1, VPAC1, VPAC2) appear in the retina. Molecular and immunohistochemical analysis demonstrated that the retinoprotective effects are most probably mainly mediated by the PAC1 receptor. The aim of the present study was to investigate the retinoprotective effects of a selective PAC1-receptor agonist maxadilan in BCCAO-induced retinopathy. Wistar rats were used in the experiment. After performing BCCAO, the right eye was treated with intravitreal maxadilan (0.1 or 1 μM), while the left eye was injected with vehicle. Sham-operated rats received the same treatment. Two weeks after the operation, retinas were processed for standard morphometric and molecular analysis. Intravitreal injection of 0.1 or 1 μM maxadilan caused significant protection in the thickness of most retinal layers and the number of cells in the GCL compared to the BCCAO-operated eyes. In addition, 1 μM maxadilan application was more effective than 0.1 μM maxadilan treatment in the ONL, INL, IPL, and the entire retina (OLM-ILM). Maxadilan treatment significantly decreased cytokine expression (CINC-1, IL-1α, and L-selectin) in ischemia. In summary, our histological and molecular analysis showed that maxadilan, a selective PAC1 receptor agonist, has a protective role in BCCAO-induced retinal degeneration, further supporting the role of PAC1 receptor conveying the retinoprotective effects of PACAP.

Secure vendor environment (SVE) for PACS

Science.gov (United States)

Honeyman-Buck, Janice; Frost, Meryll

2005-04-01

A Secure Vendor Environment (SVE) was created to protect radiology modalities from network intrusion, worms, viruses, and other forms of damaging attacks. Many vendors do not attempt any form of network security and if an institution demands a non-standard and secure installation, a future system upgrade could and frequently does eliminate any security measures installed during the initial installation. The SVE isolates the vendor equipment behind a virtual firewall on a private network that is invisible to the outside world. All interactions must go though a device containing two network interface cards called an Application Processor that acts as a store-and forward router, performs DICOM repair, proxies modality worklist, and isolates the vendor modalities. A small VPN appliance can open the device temporarily for remote access by vendor engineers. Prior to the routine installation of the SVE, vendor equipment was often attacked by hostile network intruders and viruses or worms, sometimes rendering the equipment unusable until the vendor could reload the system. The resulted in considerable clinical downtime and loss of revenue. Since the relatively low cost SVE solution has routinely been installed with all new equipment, no intrusions have occurred, although our network sniffers and intrusion detectors indicate that we are constantly being scanned for vulnerability. Purpose: To provide a secure network for vendor equipment in a PACS environment while allowing vendor access for upgrades and system repairs. Method: The network administrators at our university believe that network security should be implemented at the machine level rather than relying on a firewall. A firewall solution could conceivably block unwanted intrusion from outside the university network, but would still allow literally thousands of potential network users to get through to the PACS network. All the PACS archive, display and routing systems are individually protected from intrusion, but

Image acquisition for the pediatric radiology PACS module

International Nuclear Information System (INIS)

Ho, B.K.; Morioka, C.; Mankovich, N.J.; Stewart, B.; Huang, H.K.

1987-01-01

The prototype PACS module implemented at UCLA's pediatric radiology section has multi-modality access to image data from any of the three types of sources: digital modalities (i.e. CT, MR, and DSA), the Fuji Computed Radiography unit (FCR), and laser film digitizers. An interface unit was built to facilitate real-time data transfer from the FCR to the VAX11/750 which serves as the PACS host computer. The design of the interface unit, methods for linking to digital modalities, and characteristics of two film digitizers are described

Active component modeling for analog integrated circuit design. Model parametrization and implementation in the SPICE-PAC circuit simulator

International Nuclear Information System (INIS)

Marchal, Xavier

1992-01-01

In order to use CAD efficiently in the analysis and design of electronic Integrated circuits, adequate modeling of active non-linear devices such as MOSFET transistors must be available to the designer. Many mathematical forms can be given to those models, such as explicit relations, or implicit equations to be solved. A major requirement in developing MOS transistor models for IC simulation is the availability of electrical characteristic curves over a wide range of channel width and length, including the sub-micrometer range. To account in a convenient way for bulk charge influence on I_D_S = f(V_D_S, V_G_S, v_B_S) device characteristics, all 3 standard SPICE MOS models use an empirical fitting parameter called the 'charge sharing factor'. Unfortunately, this formulation produces models which only describe correctly either some of the short channel phenomena, or some particular operating conditions (low injection, avalanche effect, etc.). We present here a cellular model (CDM = Charge Distributed Model) implemented in the open modular SPICE-PAC Simulator; this model is derived from the 4-terminal WANG charge controlled MOSFET model, using the charge sheet approximation. The CDM model describes device characteristics in ail operating regions without introducing drain current discontinuities and without requiring a 'charge sharing factor'. A usual problem to be faced by designers when they simulate MOS ICs is to find a reliable source of model parameters. Though most models have a physical basis, some of their parameters cannot be easily estimated from physical considerations. It can also happen that physically determined parameters values do not produce a good fit to measured device characteristics. Thus it is generally necessary to extract model parameters from measured transistor data, to ensure that model equations approximate measured curves accurately enough. Model parameters extraction can be done in 2 different ways, exposed in this thesis. The first

In vitro adsorption study of fluoxetine in activated carbons and activated carbon fibres

Energy Technology Data Exchange (ETDEWEB)

Nabais, J.M. Valente; Mouquinho, A.; Galacho, C.; Carrott, P.J.M.; Ribeiro Carrott, M.M.L. [Centro de Quimica de Evora e Departamento de Quimica da Universidade de Evora, Rua Romao Ramalho no. 59, 7000-671 Evora (Portugal)

2008-05-15

We study the in vitro adsorption of fluoxetine hydrochloride by different adsorbents in simulated gastric and intestinal fluid, pH 1.2 and 7.5, respectively. The tested materials were two commercial activated carbons, carbomix and maxsorb MSC30, one activated carbon fibre produced in our laboratory and also three MCM-41 samples, also produced by us. Selected samples were modified by liquid phase oxidation and thermal treatment in order to change the surface chemistry without significant modifications to the porous characteristics. The fluoxetine adsorption follows the Langmuir model. The calculated Q{sub 0} values range from 54 to 1112 mg/g. A different adsorption mechanism was found for the adsorption of fluoxetine in activated carbon fibres and activated carbons. In the first case the most relevant factors are the molecular sieving effect and the dispersive interactions whereas in the activated carbons the mechanism seams to be based on the electrostatic interactions between the fluoxetine molecules and the charged carbon surface. Despite the different behaviours most of the materials tested have potential for treating potential fluoxetine intoxications. (author)

PACS infrastructure supporting e-learning

Energy Technology Data Exchange (ETDEWEB)

Mildenberger, Peter, E-mail: milden@radiologie.klinik.uni-mainz.de [University Medicine Mainz, Johannes Gutenberg-University Mainz, Langenbeckstr 1, Mainz (Germany); Brueggemann, Kerstin; Roesner, Freya; Koch, Katja; Ahlers, Christopher [University Medicine Mainz, Johannes Gutenberg-University Mainz, Langenbeckstr 1, Mainz (Germany)

2011-05-15

Digital imaging is becoming predominant in radiology. This has implications for teaching support, because conventional film-based concepts are now obsolete. The IHE Teaching File and Clinical Study Export (TCE) profile provides an excellent platform to enhance PACS infrastructure with educational functionality. This can be supplemented with dedicated e-learning tools.

PACS infrastructure supporting e-learning

International Nuclear Information System (INIS)

Mildenberger, Peter; Brueggemann, Kerstin; Roesner, Freya; Koch, Katja; Ahlers, Christopher

2011-01-01

Digital imaging is becoming predominant in radiology. This has implications for teaching support, because conventional film-based concepts are now obsolete. The IHE Teaching File and Clinical Study Export (TCE) profile provides an excellent platform to enhance PACS infrastructure with educational functionality. This can be supplemented with dedicated e-learning tools.

A demanding web-based PACS supported by web services technology

Science.gov (United States)

Costa, Carlos M. A.; Silva, Augusto; Oliveira, José L.; Ribeiro, Vasco G.; Ribeiro, José

2006-03-01

During the last years, the ubiquity of web interfaces have pushed practically all PACS suppliers to develop client applications in which clinical practitioners can receive and analyze medical images, using conventional personal computers and Web browsers. However, due to security and performance issues, the utilization of these software packages has been restricted to Intranets. Paradigmatically, one of the most important advantages of digital image systems is to simplify the widespread sharing and remote access of medical data between healthcare institutions. This paper analyses the traditional PACS drawbacks that contribute to their reduced usage in the Internet and describes a PACS based on Web Services technology that supports a customized DICOM encoding syntax and a specific compression scheme providing all historical patient data in a unique Web interface.

XDS-I Gateway Development for HIE Connectivity with Legacy PACS at Gil Hospital.

Science.gov (United States)

Simalango, Mikael Fernandus; Kim, Youngchul; Seo, Young Tae; Choi, Young Hwan; Cho, Yong Kyun

2013-12-01

The ability to support healthcare document sharing is imperative in a health information exchange (HIE). Sharing imaging documents or images, however, can be challenging, especially when they are stored in a picture archiving and communication system (PACS) archive that does not support document sharing via standard HIE protocols. This research proposes a standard-compliant imaging gateway that enables connectivity between a legacy PACS and the entire HIE. Investigation of the PACS solutions used at Gil Hospital was conducted. An imaging gateway application was then developed using a Java technology stack. Imaging document sharing capability enabled by the gateway was tested by integrating it into Gil Hospital's order communication system and its HIE infrastructure. The gateway can acquire radiology images from a PACS storage system, provide and register the images to Gil Hospital's HIE for document sharing purposes, and make the images retrievable by a cross-enterprise document sharing document viewer. Development of an imaging gateway that mediates communication between a PACS and an HIE can be considered a viable option when the PACS does not support the standard protocol for cross-enterprise document sharing for imaging. Furthermore, the availability of common HIE standards expedites the development and integration of the imaging gateway with an HIE.

Completion and Testing of PACS SWIR Channel

Data.gov (United States)

National Aeronautics and Space Administration — PACS SWIR has important technological innovations that will be necessary to meet the mission requirements for wide FOV, hyperangle capability, high polarimetric...

Rapid removal of bisphenol A on highly ordered mesoporous carbon.

Science.gov (United States)

Sui, Qian; Huang, Jun; Liu, Yousong; Chang, Xiaofeng; Ji, Guangbin; Deng, Shubo; Xie, Tao; Yu, Gang

2011-01-01

Bisphenol A (BPA) is of global concern due to its disruption of endocrine systems and ubiquity in the aquatic environment. It is important, therefore, that efforts are made to remove it from the aqueous phase. A novel adsorbent, mesoporous carbon CMK-3, prepared from hexagonal SBA-15 mesoporous silica was studied for BPA removal from aqueous phase, and compared with conventional powdered activated carbon (PAC). Characterization of CMK-3 by transmission electron microscopy (TEM), X-ray diffraction, and nitrogen adsorption indicated that prepared CMK-3 had an ordered mesoporous structure with a high specific surface area of 920 m2/g and a pore-size of about 4.9 nm. The adsorption of BPA on CMK-3 followed a pseudo second-order kinetic model. The kinetic constant was 0.00049 g/(mg x min), much higher than the adsorption of BPA on PAC. The adsorption isotherm fitted slightly better with the Freundlich model than the Langmuir model, and adsorption capacity decreased as temperature increased from 10 to 40 degrees C. No significant influence of pH on adsorption was observed at pH 3 to 9; however, adsorption capacity decreased dramatically from pH 9 to 13.

PAC1- and VPAC2 receptors in light regulated behavior and physiology: Studies in single and double mutant mice.

Directory of Open Access Journals (Sweden)

Jens Hannibal

Full Text Available The two sister peptides, pituitary adenylate cyclase activating polypeptide (PACAP and vasoactive intestinal polypeptide (VIP and their receptors, the PAC1 -and the VPAC2 receptors, are involved in regulation of the circadian timing system. PACAP as a neurotransmitter in the retinohypothalamic tract (RHT and VIP as a neurotransmitter, involved in synchronization of SCN neurons. Behavior and physiology in VPAC2 deficient mice are strongly regulated by light most likely as a result of masking. Consequently, we used VPAC2 and PAC1/VPAC2 double mutant mice in comparison with PAC1 receptor deficient mice to further elucidate the role of PACAP in the light mediated regulation of behavior and physiology of the circadian system. We compared circadian rhythms in mice equipped with running wheels or implanted radio-transmitter measuring core body temperature kept in a full photoperiod ((FPP(12:12 h light dark-cycles (LD and skeleton photo periods (SPP at high and low light intensity. Furthermore, we examined the expression of PAC1- and VPAC2 receptors in the SCN of the different genotypes in combination with visualization of PACAP and VIP and determined whether compensatory changes in peptide and/or receptor expression in the reciprocal knockouts (KO (PAC1 and VPAC2 had occurred. Our data demonstrate that in although being closely related at both ligand and receptor structure/sequence, PACAP/PAC1 receptor signaling are independent of VIP/VPAC2 receptor signaling and vice versa. Furthermore, lack of either of the receptors does not result in compensatory changes at neither the physiological or anatomical level. PACAP/PAC1 signaling is important for light regulated behavior, VIP/VPAC2signaling for stable clock function and both signaling pathways may play a role in shaping diurnality versus nocturnality.

Influence map baserad Ms. Pac-Man och Ghost Kontroller

OpenAIRE

Svensson, Johan

2012-01-01

This thesis will cover the use oftheinfluence map technique applied to the retro game Ms. Pac-Man. A game thatis easy to learn but hard to master. The Ms. Pac-Man controller is implemented with five main parameters that alters the behaviour of the controller while the Ghost controller have three parameters. The experimental results of the controllers is explored to using the alterations of the parameters to find its peak of performance. The conclusion from using the influence map for this gam...

Characterization of Activated Carbons from Oil-Palm Shell by CO2 Activation with No Holding Carbonization Temperature

Directory of Open Access Journals (Sweden)

S. G. Herawan

2013-01-01

Full Text Available Activated carbons can be produced from different precursors, including coals of different ranks, and lignocellulosic materials, by physical or chemical activation processes. The objective of this paper is to characterize oil-palm shells, as a biomass byproduct from palm-oil mills which were converted into activated carbons by nitrogen pyrolysis followed by CO2 activation. The effects of no holding peak pyrolysis temperature on the physical characteristics of the activated carbons are studied. The BET surface area of the activated carbon is investigated using N2 adsorption at 77 K with selected temperatures of 500, 600, and 700°C. These pyrolysis conditions for preparing the activated carbons are found to yield higher BET surface area at a pyrolysis temperature of 700°C compared to selected commercial activated carbon. The activated carbons thus result in well-developed porosities and predominantly microporosities. By using this activation method, significant improvement can be obtained in the surface characteristics of the activated carbons. Thus this study shows that the preparation time can be shortened while better results of activated carbon can be produced.

Business Model for the Security of a Large-Scale PACS, Compliance with ISO/27002:2013 Standard.

Science.gov (United States)

Gutiérrez-Martínez, Josefina; Núñez-Gaona, Marco Antonio; Aguirre-Meneses, Heriberto

2015-08-01

Data security is a critical issue in an organization; a proper information security management (ISM) is an ongoing process that seeks to build and maintain programs, policies, and controls for protecting information. A hospital is one of the most complex organizations, where patient information has not only legal and economic implications but, more importantly, an impact on the patient's health. Imaging studies include medical images, patient identification data, and proprietary information of the study; these data are contained in the storage device of a PACS. This system must preserve the confidentiality, integrity, and availability of patient information. There are techniques such as firewalls, encryption, and data encapsulation that contribute to the protection of information. In addition, the Digital Imaging and Communications in Medicine (DICOM) standard and the requirements of the Health Insurance Portability and Accountability Act (HIPAA) regulations are also used to protect the patient clinical data. However, these techniques are not systematically applied to the picture and archiving and communication system (PACS) in most cases and are not sufficient to ensure the integrity of the images and associated data during transmission. The ISO/IEC 27001:2013 standard has been developed to improve the ISM. Currently, health institutions lack effective ISM processes that enable reliable interorganizational activities. In this paper, we present a business model that accomplishes the controls of ISO/IEC 27002:2013 standard and criteria of security and privacy from DICOM and HIPAA to improve the ISM of a large-scale PACS. The methodology associated with the model can monitor the flow of data in a PACS, facilitating the detection of unauthorized access to images and other abnormal activities.

A comparison of the time required by radiologists for the preparation of clinico-radiological meetings when film and PACS are used

International Nuclear Information System (INIS)

Weatherburn, G.; Bryan, S.; Cousins, C.

2000-01-01

The hypothesis was that when a hospital-wide Picture Archive and Communications System (PACS) is used, preparation for clinico-radiological meetings is faster, and more images are available, than when a conventional film system is used. This paper reports a study which compared the preparation time by radiologists when film was used with the time for the same activity when a hospital-wide PACS was used at Hammersmith Hospital for the preparation of the respiratory medicine and hepato-biliary meetings. It was found that when PACS was used the time per patient to prepare for the respiratory medicine session was reduced by 11.1 min and that similarly, 16 min per patient was saved in the preparation of the hepato-biliary sessions. The number of images which were unavailable for the session was reduced when PACS was in operation, but this reduction was not shown to be statistically significant. The introduction of PACS at Hammersmith Hospital has significantly reduced the time spent by radiologists in preparing for the two clinico-radiological sessions studied and, if this is extended to the other numerous sessions held each week, contributes to a considerable saving of staff time within the radiology department. (orig.)

Production of palm kernel shell-based activated carbon by direct physical activation for carbon dioxide adsorption.

Science.gov (United States)

Rashidi, Nor Adilla; Yusup, Suzana

2018-05-09

The feasibility of biomass-based activated carbons has received a huge attention due to their excellent characteristics such as inexpensiveness, good adsorption behaviour and potential to reduce a strong dependency towards non-renewable precursors. Therefore, in this research work, eco-friendly activated carbon from palm kernel shell that has been produced from one-stage physical activation by using the Box-Behnken design of Response Surface Methodology is highlighted. The effect of three input parameters-temperature, dwell time and gas flow rate-towards product yield and carbon dioxide (CO 2 ) uptake at room temperature and atmospheric pressure are studied. Model accuracy has been evaluated through the ANOVA analysis and lack-of-fit test. Accordingly, the optimum condition in synthesising the activated carbon with adequate CO 2 adsorption capacity of 2.13 mmol/g and product yield of 25.15 wt% is found at a temperature of 850 °C, holding time of 60 min and CO 2 flow rate of 450 cm 3 /min. The synthesised activated carbon has been characterised by diverse analytical instruments including thermogravimetric analyser, scanning electron microscope, as well as N 2 adsorption-desorption isotherm. The characterisation analysis indicates that the synthesised activated carbon has higher textural characteristics and porosity, together with better thermal stability and carbon content as compared to pristine palm kernel shell. Activated carbon production via one-step activation approach is economical since its carbon yield is within the industrial target, whereas CO 2 uptake is comparable to the synthesised activated carbon from conventional dual-stage activation, commercial activated carbon and other published data from literature.

Picture archiving and communication systems (PACS) in clinical practice

International Nuclear Information System (INIS)

Carreno Pedemonte, J.C.; Piqueras Pardellans, J.; Lucaya Layret, J.

1994-01-01

Picture archiving and communication systems (PACS) were developed as a technological response to the complex management of the growing amount of information generated by the different diagnostic imaging methods. This article documents the process of the progressive implementation, starting in January 1991, of the first complete PACS installed in our country. The system installed in our center is composed of acquisition modules for all the imaging methods (computed radiography, ultrasound, computed tomography, digital fluoroscopy and magnetic resonance), a central processing unit, an automatic optical disk for storage and a network of image viewing and diagnostic stations. The preliminary results obtained with its implementation demonstrate that PACS provide a series of functional advantages, especially at the image storage and display levels. In spite of these conveniences, the present high costs of acquisition and maintenance, together with certain technical problems as a result of its complexity, will signify that its generalized application for all imaging methods will not become a reality at most centers in the near future

PACS: Picture Archiving and Communication Systems

International Nuclear Information System (INIS)

Gell, G.; Schneider, G.H.; Becker, M.; Wiltgen, M.

1988-01-01

A growing number of medical imaging modalities produces images that are initially calculated and stored as digital information in a computer. For diagnosis, archiving and communication a hardcopy (usually on X-ray film) is produced from these data. It is estimated that in 1995 about 80% of all imaging procedures will generate digital images. This trend leads to the development of systems, where the X-ray film is not only replaced in his function as a radiation detector, but also in his other functions as the medium for image presentation, image communication and image archiving. In short, one wants a completely digital picture archiving and communication system (PACS). The rationale behind PACS efforts is to achieve better functionality and to save costs, mainly by reducing the consumption of expensive X-ray films and the need for storage space for film archives. 7 refs., 2 figs. (Author)

Integration of radiology and hospital information systems (RIS, HIS) with PACS

International Nuclear Information System (INIS)

Mosser, H.; Urban, M.; Hruby, W.; Duerr, M.; Rueger, W.

1992-01-01

PACS development has now reached a stage where it can clearly be stated that the technology for storage, networking and display in a fully digital environment is available. This is reflected by an already large and rapidly increasing number of PACS installations in USA, Western Europe and Japan. Such installations consist of a great variety of information systems, more or less interconnected, like PACS, HIS, RIS and other departmental systems, differing in both hardware and software. Various data -even if they only concern one person- are stored in different systems distributed in the hospital. The integration of all digital systems into a functional unit is determined by the radiologist's need of quick access to all relevant information regardless where it is stored. The interconnection and functional integration of all digital systems in the hospital determine the clinical benefits of PACS. This paper describes the radiologist's requirements concerning this integration, and presents some realistic solutions such as the Siemens ISI (Information System Interface), and a mobile viewing station for the wards (visitBox). (author). 9 refs., 4 figs

Technical feasibility study of a low-cost hybrid PAC-UF system for wastewater reclamation and reuse: a focus on feedwater production for low-pressure boilers.

Science.gov (United States)

Amosa, Mutiu Kolade; Jami, Mohammed Saedi; Alkhatib, Ma'an Fahmi R; Majozi, Thokozani

2016-11-01

This study has applied the concept of the hybrid PAC-UF process in the treatment of the final effluent of the palm oil industry for reuse as feedwater for low-pressure boilers. In a bench-scale set-up, a low-cost empty fruit bunch-based powdered activated carbon (PAC) was employed for upstream adsorption of biotreated palm oil mill effluent (BPOME) with the process conditions: 60 g/L dose of PAC, 68 min of mixing time and 200 rpm of mixing speed, to reduce the feedwater strength, alleviate probable fouling of the membranes and thus improve the process flux (productivity). Three polyethersulfone ultrafiltration membranes of molecular weight cut-off (MWCO) of 1, 5 and 10 kDa were investigated in a cross-flow filtration mode, and under constant transmembrane pressures of 40, 80, and 120 kPa. The permeate qualities of the hybrid processes were evaluated, and it was found that the integrated process with the 1 kDa MWCO UF membrane yielded the best water quality that falls within the US EPA reuse standard for boiler-feed and cooling water. It was also observed that the permeate quality is fit for extended reuse as process water in the cement, petroleum and coal industries. In addition, the hybrid system's operation consumed 37.13 Wh m -3 of energy at the highest applied pressure of 120 kPa, which is far lesser than the typical energy requirement range (0.8-1.0 kWh m -3 ) for such wastewater reclamation.

Development and practice for a PACS-based interactive teaching model for CT image

International Nuclear Information System (INIS)

Tian Junzhang; Jiang Guihua; Zheng Liyin; Wang Ling; Wenhua; Liang Lianbao

2002-01-01

Objective: To explore the interactive teaching model for CT imaging based on PACS, and provide the clinician and young radiologist with continued medical education. Methods: 100 M trunk net was adopted in PACS and 10 M was exchanged on desktop. Teaching model was installed in browse and diagnosis workstation. Teaching contents were classified according to region and managed according to branch model. Text data derived from authoritative textbooks, monograph, and periodicals. Imaging data derived from cases proved by pathology and clinic. The data were obtained through digital camera and scanner or from PACS. After edited and transformed into standard digital image through DICOM server, they were saved in HD of PACS image server with file form. Results: Teaching model for CT imaging provided kinds of cases of CT sign, clinic characteristics, pathology and distinguishing diagnosis. Normal section anatomy, typical image, and its notation could be browsed real time. Teaching model for CT imaging could provide reference to teaching, diagnosis and report. Conclusion: PACS-based teaching model for CT imaging could provide interactive teaching and scientific research tool and improve work quality and efficiency

How can the impact of PACS on inpatient length of hospital stay be established?

Science.gov (United States)

Bryan, Stirling; Muris, Nicole; Keen, Justin; Weatherburn, Gwyneth C.; Buxton, Martin J.

1994-05-01

Many have argued that the introduction of a large-scale PACS system into a hospital will bring about reductions in the length of inpatient hospital stays. There is currently no convicting empirical evidence to support such claims. As part of the independent evaluation exercise being undertaken alongside the Hammersmith Hospital PACS implementation, an assessment is being made of the impact of PACS on length of stay for selected patient groups. This paper reports the general research methods being employed to undertake this assessment and provides some baseline results from the analysis of total hip replacement patients and total knee replacement patients treated prior to the introduction of PACS.

Workflow optimization beyond RIS and PACS

International Nuclear Information System (INIS)

Treitl, M.; Wirth, S.; Lucke, A.; Nissen-Meyer, S.; Trumm, C.; Rieger, J.; Pfeifer, K.-J.; Reiser, M.; Villain, S.

2005-01-01

Technological progress and the rising cost pressure on the healthcare system have led to a drastic change in the work environment of radiologists today. The pervasive demand for workflow optimization and increased efficiency of its activities raises the question of whether by employment of electronic systems, such as RIS and PACS, the potentials of digital technology are sufficiently used to fulfil this demand. This report describes the tasks and structures in radiology departments, which so far are only insufficiently supported by commercially available electronic systems but are nevertheless substantial. We developed and employed a web-based, integrated workplace system, which simplifies many daily tasks of departmental organization and administration apart from well-established tasks of documentation. Furthermore, we analyzed the effects exerted on departmental workflow by employment of this system for 3 years. (orig.) [de

Removal of paraquat and linuron from water by continuous flow adsorption/ ultrafiltration membrane processes

International Nuclear Information System (INIS)

Zahoor, M.

2013-01-01

The magnetic activated carbon (MAC) was prepared, characterized and compared with powdered activated carbon (PAC) for its adsorptive parameters. Both adsorbents were then used in combination ultrafiltration (UF) membrane as pretreatment for the removal of paraquat and linuron from water. The comparison of membrane parameters like percent retention, permeate flux and backwash times for PAC/UF and MAC/UF hybrid processes showed that percent retention of paraquat and linuron was high for PAC due to its high surface area. However due to cake formation over membrane surface the decline permeate fluxes and long backwash times for PAC were observed. PAC also caused blackening of pipes and flow meter. MAC (an iron oxide and PAC composite) was removed from slurry through magnet thus no cake formation and secondary problems observed for PAC was not encountered. Also the backwash times were minimum for MAC/UF process. (author)

PACS spectroscopy of OH/IR stars

NARCIS (Netherlands)

Lombaert, R.; de Vries, B.L.; Decin, L.; Blommaert, J.A.D.L.; Royer, Pierre; De Beck, E.; de Koter, A.; Waters, L.B.F.M.

2011-01-01

Observations of high-excitation molecular emission lines can greatly increase our understanding of AGB winds, as they trace the innermost regions of the circumstellar envelope. The PACS spectrometer on-board the Herschel Space Telescope1, provides for the first time the spectral resolution and

Lessons learned from a whole hospital PACS installation. Picture Archiving and Communication System.

Science.gov (United States)

Pilling, J R

2002-09-01

The Norfolk and Norwich University Hospital has incorporated a fully filmless Picture Archiving and Communication System (PACS) as part of a new hospital provision using PFI funding. The PACS project has been very successful and has met with unanimous acclaim from radiologists and clinicians. A project of this size cannot be achieved without learning some lessons from mistakes and recognising areas where attention to detail resulted in a successful implementation. This paper considers the successes and problems encountered in a large PACS installation.

A study on reduction effect of processing wastewater by introduction of PACS

International Nuclear Information System (INIS)

Ko, Shin Kwan; Yang, Han Jun; Han, Dong Kyoon; Kim, Wook Dong; Kang, Bung Sam

2007-01-01

There are some positive effects by the introduction of PACS (Picture Archiving Communication System). This study is to analyze the mutual relation between before and after of the introduction of PACS in terms of the environment effect. It is supposed to cause the reduction of developing and fixing wastewater according to the increase in the rate of a non-film. This study also show the amount of wastewater. Target places were the department of image medicine (diagnostic radiation) of the general hospitals in Seoul and Gyeonggido, which are equipped with full PACS. The authors examined questionnaires on the number of projection, the number of indirect projection, the amount of the film used, the number of radiation image CD loan, the amount of the developing and fixing solution used, the change of the amount of fixing wastewater. According to the analysis, we analyzed the change of the amount of developing and fixing solution per a film and the change of the amount of developing and fixing wastewater which is supposed to be reduced proportionally by the introduction of PACS. We got conclusion as below after analyzing 8 hospitals except the largest and the least amount of examination, film used, developing and fixing solution and the amount of developing and fixing wastewater in order to decrease the deviation from 10 general hospitals located in Seoul and Gyeonggido. We compared data one year before adopting PACS Versus 3 years after adopting PACS. The frequencies of examination increased to 7,357.7 cases per month but the amount of film used decreased to 90%, from 42,774.4 to 4,181.88 after adopting the PACS. 3 years after adopting PACS, monthly average amount of developing solution used decreased to 92% and the monthly average amount of fixing solution decreased to 86%. Monthly average amount of developing solution used per film increased to 1.49 times and fixing solution increased as much as three times. Monthly average wastewater for developing decreased to 88

PACS and its hospital-wide implementation: A case study at the Madigan Army Medical Center

International Nuclear Information System (INIS)

Choi, Hyung Sik; Kim, Yong Min; Smith, Donald V.; Bender, Gregory N.

1993-01-01

PACS represents the future of radiology in modern hospitals. Workstations and databases can be developed to substantially increase clinician's productivity, improve diagnostic accuracy, and make a large amount of knowledge and patient information available on-line to the physician. Currently, there are several hospitals in the process of implementing a total PACS system. They include Madigan Army Medical Center (Tacoma, Washington), VA Hospital in Baltimore, and Hammersmith Hospital in London (1). In order to provide the radiologist, the clinicians, and other health personnel in Korea with the general concept of PACS and its up-to-date status report, we describe the MDIS system being implemented in MAMC (Madigan Army Medical Center) which is the first hospital-wide large-scale PACS in the world. The major PACS components in MAMC have been installed since March 1992 and the full system implementation will be completed by summer 1993. The goal of the MDIS system in MAMC is to increase to more than 90% filmless by the end of 1993. In this paper, we discuss the introduction and background of PACS and its potential benefits, the current status of PACS installation in MAMC and the future plan, and the flow of image data and text information in MAMC

Cost-effective data storage/archival subsystem for functional PACS

Science.gov (United States)

Chen, Y. P.; Kim, Yongmin

1993-09-01

Not the least of the requirements of a workable PACS is the ability to store and archive vast amounts of information. A medium-size hospital will generate between 1 and 2 TBytes of data annually on a fully functional PACS. A high-speed image transmission network coupled with a comparably high-speed central data storage unit can make local memory and magnetic disks in the PACS workstations less critical and, in an extreme case, unnecessary. Under these circumstances, the capacity and performance of the central data storage subsystem and database is critical in determining the response time at the workstations, thus significantly affecting clinical acceptability. The central data storage subsystem not only needs to provide sufficient capacity to store about ten days worth of images (five days worth of new studies, and on the average, about one comparison study for each new study), but also supplies images to the requesting workstation in a timely fashion. The database must provide fast retrieval responses upon users' requests for images. This paper analyzes both advantages and disadvantages of multiple parallel transfer disks versus RAID disks for short-term central data storage subsystem, as well as optical disk jukebox versus digital recorder tape subsystem for long-term archive. Furthermore, an example high-performance cost-effective storage subsystem which integrates both the RAID disks and high-speed digital tape subsystem as a cost-effective PACS data storage/archival unit are presented.

Separating the Effects of Tropical Atlantic and Pacific SST-driven Climate Variability on Amazon Carbon Exchange

Science.gov (United States)

Liptak, J.; Keppel-Aleks, G.

2016-12-01

Amazon forests store an estimated 25% percent of global terrestrial carbon per year1, 2, but the responses of Amazon carbon uptake to climate change is highly uncertain. One source of this uncertainty is tropical sea surface temperature variability driven by teleconnections. El Nino-Southern Oscillation (ENSO) is a key driver of year-to-year Amazon carbon exchange, with associated temperature and precipitation changes favoring net carbon storage in La Nina years, and net carbon release during El Nino years3. To determine how Amazon climate and terrestrial carbon fluxes react to ENSO alone and in concert with other SST-driven teleconnections such as the Atlantic Multidecadal Oscillation (AMO), we force the atmosphere (CAM5) and land (CLM4) components of the CESM(BGC) with prescribed monthly SSTs over the period 1950—2014 in a Historical control simulation. We then run an experiment (PAC) with time-varying SSTs applied only to the tropical equatorial Pacific Ocean, and repeating SST seasonal cycle climatologies elsewhere. Limiting SST variability to the equatorial Pacific indicates that other processes enhance ENSO-driven Amazon climate anomalies. Compared to the Historical control simulation, warming, drying and terrestrial carbon loss over the Amazon during El Nino periods are lower in the PAC simulation, especially prior to 1990 during the cool phase of the AMO. Cooling, moistening, and net carbon uptake during La Nina periods are also reduced in the PAC simulation, but differences are greater after 1990 during the warm phase of the AMO. By quantifying the relationships among climate drivers and carbon fluxes in the Historical and PAC simulations, we both assess the sensitivity of these relationships to the magnitude of ENSO forcing and quantify how other teleconnections affect ENSO-driven Amazon climate feedbacks. We expect that these results will help us improve hypotheses for how Atlantic and Pacific climate trends will affect future Amazon carbon carbon

Enterprise-wide PACS: beyond radiology, an architecture to manage all medical images.

Science.gov (United States)

Bandon, David; Lovis, Christian; Geissbühler, Antoine; Vallée, Jean-Paul

2005-08-01

Picture archiving and communication systems (PACS) have the vocation to manage all medical images acquired within the hospital. To address the various situations encountered in the imaging specialties, the traditional architecture used for the radiology department has to evolve. We present our preliminarily results toward an enterprise-wide PACS intended to support all kind of image production in medicine, from biomolecular images to whole-body pictures. Our solution is based on an existing radiologic PACS system from which images are distributed through an electronic patient record to all care facilities. This platform is enriched with a flexible integration framework supporting digital image communication in medicine (DICOM) and DICOM-XML formats. In addition, a generic workflow engine highly customizable is used to drive work processes. Echocardiology; hematology; ear, nose, and throat; and dermatology, including wounds, follow-up is the first implemented extensions outside of radiology. We also propose a global strategy for further developments based on three possible architectures for an enterprise-wide PACS.

Effect of powdered activated carbon technology on short-cut nitrogen removal for coal gasification wastewater.

Science.gov (United States)

Zhao, Qian; Han, Hongjun; Xu, Chunyan; Zhuang, Haifeng; Fang, Fang; Zhang, Linghan

2013-08-01

A combined process consisting of a powdered activated carbon technology (PACT) and short-cut biological nitrogen removal reactor (SBNR) was developed to enhance the removal efficiency of the total nitrogen (TN) from the effluent of an upflow anaerobic sludge bed (UASB) reactor, which was used to treat coal gasification wastewater (CGW). The SBNR performance was improved with the increasing of COD and TP removal efficiency via PACT. The average removal efficiencies of COD and TP in PACT were respectively 85.80% and 90.30%. Meanwhile, the NH3-N to NO2-N conversion rate was achieved 86.89% in SBNR and the total nitrogen (TN) removal efficiency was 75.54%. In contrast, the AOB in SBNR was significantly inhibited without PACT or with poor performance of PACT in advance, which rendered the removal of TN. Furthermore, PAC was demonstrated to remove some refractory compounds, which therefore improved the biodegradability of the coal gasification wastewater. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Crystal structure of the PAC1R extracellular domain unifies a consensus fold for hormone recognition by class B G-protein coupled receptors.

Directory of Open Access Journals (Sweden)

Shiva Kumar

Full Text Available Pituitary adenylate cyclase activating polypeptide (PACAP is a member of the PACAP/glucagon family of peptide hormones, which controls many physiological functions in the immune, nervous, endocrine, and muscular systems. It activates adenylate cyclase by binding to its receptor, PAC1R, a member of class B G-protein coupled receptors (GPCR. Crystal structures of a number of Class B GPCR extracellular domains (ECD bound to their respective peptide hormones have revealed a consensus mechanism of hormone binding. However, the mechanism of how PACAP binds to its receptor remains controversial as an NMR structure of the PAC1R ECD/PACAP complex reveals a different topology of the ECD and a distinct mode of ligand recognition. Here we report a 1.9 Å crystal structure of the PAC1R ECD, which adopts the same fold as commonly observed for other members of Class B GPCR. Binding studies and cell-based assays with alanine-scanned peptides and mutated receptor support a model that PAC1R uses the same conserved fold of Class B GPCR ECD for PACAP binding, thus unifying the consensus mechanism of hormone binding for this family of receptors.

A high performance lithium ion capacitor achieved by the integration of a Sn-C anode and a biomass-derived microporous activated carbon cathode.

Science.gov (United States)

Sun, Fei; Gao, Jihui; Zhu, Yuwen; Pi, Xinxin; Wang, Lijie; Liu, Xin; Qin, Yukun

2017-02-03

Hybridizing battery and capacitor materials to construct lithium ion capacitors (LICs) has been regarded as a promising avenue to bridge the gap between high-energy lithium ion batteries and high-power supercapacitors. One of the key difficulties in developing advanced LICs is the imbalance in the power capability and charge storage capacity between anode and cathode. Herein, we design a new LIC system by integrating a rationally designed Sn-C anode with a biomass-derived activated carbon cathode. The Sn-C nanocomposite obtained by a facile confined growth strategy possesses multiple structural merits including well-confined Sn nanoparticles, homogeneous distribution and interconnected carbon framework with ultra-high N doping level, synergically enabling the fabricated anode with high Li storage capacity and excellent rate capability. A new type of biomass-derived activated carbon featuring both high surface area and high carbon purity is also prepared to achieve high capacity for cathode. The assembled LIC (Sn-C//PAC) device delivers high energy densities of 195.7 Wh kg -1 and 84.6 Wh kg -1 at power densities of 731.25 W kg -1 and 24375 W kg -1 , respectively. This work offers a new strategy for designing high-performance hybrid system by tailoring the nanostructures of Li insertion anode and ion adsorption cathode.

Preparation of very pure active carbon

International Nuclear Information System (INIS)

Sloot, H.A. van der; Hoede, D.; Zonderhuis, J.; Meijer, C.

1980-02-01

The preparation of very pure active carbon is described. Starting from polyvinylidene chloride active carbon is prepared by carbonization in a nitrogen atmosphere, grinding, sieving and activation of the powder fraction with CO 2 at 950 0 to approximately 50% burn-off. The concentrations of trace and major elements are reduced to the ppb and ppm level, respectively. In the present set-up 100 g of carbon grains and approximately 50 g of active carbon powder can be produced weekly

Hexavalent chromium removal using aerobic activated sludge batch ...

African Journals Online (AJOL)

The following Cr(VI) removal systems were tested: activated sludge alone; activated sludge with an external electron donor (5 g/. of lactose); activated sludge with PAC addition (4 g/.); activated sludge with both PAC and lactose; and PAC alone. The results reported here showed that activated sludges are capable of ...

From shared data to sharing workflow: Merging PACS and teleradiology

International Nuclear Information System (INIS)

Benjamin, Menashe; Aradi, Yinon; Shreiber, Reuven

2010-01-01

Due to a host of technological, interface, operational and workflow limitations, teleradiology and PACS/RIS were historically developed as separate systems serving different purposes. PACS/RIS handled local radiology storage and workflow management while teleradiology addressed remote access to images. Today advanced PACS/RIS support complete site radiology workflow for attending physicians, whether on-site or remote. In parallel, teleradiology has emerged into a service of providing remote, off-hours, coverage for emergency radiology and to a lesser extent subspecialty reading to subscribing sites and radiology groups. When attending radiologists use teleradiology for remote access to a site, they may share all relevant patient data and participate in the site's workflow like their on-site peers. The operation gets cumbersome and time consuming when these radiologists serve multi-sites, each requiring a different remote access, or when the sites do not employ the same PACS/RIS/Reporting Systems and do not share the same ownership. The least efficient operation is of teleradiology companies engaged in reading for multiple facilities. As these services typically employ non-local radiologists, they are allowed to share some of the available patient data necessary to provide an emergency report but, by enlarge, they do not share the workflow of the sites they serve. Radiology stakeholders usually prefer to have their own radiologists perform all radiology tasks including interpretation of off-hour examinations. It is possible with current technology to create a system that combines the benefits of local radiology services to multiple sites with the advantages offered by adding subspecialty and off-hours emergency services through teleradiology. Such a system increases efficiency for the radiology groups by enabling all users, regardless of location, to work 'local' and fully participate in the workflow of every site. We refer to such a system as SuperPACS.

PACS: Do clinical users benefit from it as a training adjunct? | van ...

African Journals Online (AJOL)

Although a PACS relates specifically to the archiving and retrieval of radiological images and reports, it became clear from the feedback received from medical clinicians (who ... The advantages of PACS as a positive training adjunct were highlighted in the areas of multi-site viewing and consultation, the possibility of image ...

Operator interface design considerations for a PACS information management system

Science.gov (United States)

Steinke, James E.; Nabijee, Kamal H.; Freeman, Rick H.; Prior, Fred W.

1990-08-01

As prototype PACS grow into fully digital departmental and hospital-wide systems, effective information storage and retrieval mechanisms become increasingly important. Thus far, designers of PACS workstations have concentrated on image communication and display functionality. The new challenge is to provide appropriate operator interface environments to facilitate information retrieval. The "Marburg Model" 1 provides a detailed analysis of the functions, control flows and data structures used in Radiology. It identifies a set of "actors" who perform information manipulation functions. Drawing on this model and its associated methodology it is possible to identify four modes of use of information systems in Radiology: Clinical Routine, Research, Consultation, and Administration. Each mode has its own specific access requirements and views of information. An operator interface strategy appropriate for each mode will be proposed. Clinical Routine mode is the principal concern of PACS primary diagnosis workstations. In a full PACS implementation, such workstations must provide a simple and consistent navigational aid for the on-line image database, a local work list of cases to be reviewed, and easy access to information from other hospital information systems. A hierarchical method of information access is preferred because it provides the ability to start at high-level entities and iteratively narrow the scope of information from which to select subsequent operations. An implementation using hierarchical, nested software windows which fulfills such requirements shall be examined.

Whole-slide imaging in pathology: the potential impact on PACS

Science.gov (United States)

Horii, Steven C.

2007-03-01

Pathology, the medical specialty charged with the evaluation of macroscopic and microscopic aspects of disease, is increasingly turning to digital imaging. While the conventional tissue blocks and glass slides form an "archive" that pathology departments must maintain, digital images acquired from microscopes or digital slide scanners are increasingly used for telepathology, consultation, and intra-facility communication. Since many healthcare facilities are moving to "enterprise PACS" with departments in addition to radiology using the infrastructure of such systems, some understanding of the potential of whole-slide digital images is important. Network and storage designers, in particular, are very likely to be impacted if a significant number of such images are to be moved on, or stored (even temporarily) in, enterprise PACS. As an example, a typical commercial whole-slide imaging system typically generates 15 gigabytes per slide scanned (per focal plane). Many of these whole-slide scanners have a throughput of 1000 slides per day. If that full capacity is used and all the resulting digital data is moved to the enterprise PACS, it amounts to 15 terabytes per day; the amount of data a large radiology department might generate in a year or two. This paper will review both the clinical scenarios of whole-slide imaging as well as the resulting data volumes. The author will emphasize the potential PACS infrastructure impact of such huge data volumes.

Combined PACS and intranet information system in a University Hospital; Kombiniertes PACS und Intranet-Informationssystem an einem Universitaetsklinikum

Energy Technology Data Exchange (ETDEWEB)

Heiss, D.; Pfluger, T.; Pfeifer, K.J.; Hahn, K. [Muenchen Univ. (Germany). Inst. fuer Radiologische Diagnostik; Koenig, A.; Endres, S. [Muenchen Univ. (Germany). Medizinische Klinik Innenstadt

2000-06-01

Purpose: The Department of Radiology at the University Hospital Innenstadt Munich provides all clinical departments of a large university hospital with several radiology units at different locations. During the last four years all units have been fully digitalized with a stepwise installation of a PACS. The PACS also processes images from the Nuclear Medicine Department. Methods: As image modalities, archive systems and review workstations, we use devices from multiple vendors, which are integrated into a consistent system using the DICOM standard. The hospital has developed its own RIS and an intranet information system, which provides access to all reports and images from radiology for all clinical departments inside the hospital. Additionally, other clinical information such as laboratory results or ECG examinations are available through the system. Results: After one year of operation, the system succeeded in the clinical routine work as the primary source for radiological reports and images as well as for laboratory values. Conclusion: The advantages of digitalization were, besides reduction of film cost, especially optimizations of work flow with access to digital images from every where at any time. (orig.) [German] Ziel: Das Institut fuer Radiologische Diagnostik am Universitaetsklinikum Muenchen - Innenstadt versorgt mit mehreren, dezentral gelegenen Roentgenbereichen alle klinischen Abteilungen eines grossen Universitaetsklinikums. In einem Projekt der vergangenen vier Jahre wurden alle Bereiche durch die schrittweise Installation eines PACS vollstaendig digitalisiert. Dabei wurden auch nuklearmedizinische Bilddaten aus der Klinik und Poliklinik fuer Nuklearmedizin im System verarbeitet. Methoden: Eingesetzt wurden als Bilderzeuger, Archivsystem und Befundungsstationen Geraete unterschiedlicher Hersteller, die dank des DICOM Standards in einem einheitlichen System integriert sind. Neben dem PACS wurde von Mitarbeitern der Klinik ein RIS und ein Intranet

The impact of a picture archiving and communication system (PACS) upon an intensive care unit

International Nuclear Information System (INIS)

Watkins, Jessamy; Weatherburn, Gwyn; Bryan, Stirling

2000-01-01

Objective: The aim of the study was to assess the effect of the introduction of PACS (Picture Archiving and Communication System) upon image availability in an Intensive Care Unit (ICU) and the consequent impact upon the behaviour of the ICU physicians, in terms of the initiation of image-based clinical actions. Design: A before and after study was used to compare the speed of image availability prior to, and following, the implementation of a hospital-wide PACS. Setting: The research was part of an economic evaluation of PACS at Hammersmith Hospital, West London. Patients and participants: All ICU patients who were X-rayed during two pre-PACS and one post-PACS data collection periods were included within the study. Measurements: The times of: the X-ray request; acquisition; availability on ICU; and of any image-based clinical action taken by the ICU physician were recorded by radiographers and ICU physicians. Results: PACS significantly reduced the time between request and image availability on ICU for routine X-rays but did not have any measurable impact upon the time clinical actions were initiated by ICU physicians. The data on non-routine images were statistically inconclusive. Conclusions: This study shows that PACS significantly improves the speed of delivery of routine images to the ICU, but it appears that the instigation of image-based clinical actions is determined by other organisational factors in ICU, such as ward rounds, rather than the availability of the image for viewing. Further work is required on non-routine X-rays to clarify the impact of PACS on physician behaviour in clinically urgent situations

A strongly quasiconvex PAC-Bayesian bound

DEFF Research Database (Denmark)

Thiemann, Niklas; Igel, Christian; Wintenberger, Olivier

2017-01-01

We propose a new PAC-Bayesian bound and a way of constructing a hypothesis space, so that the bound is convex in the posterior distribution and also convex in a trade-off parameter between empirical performance of the posterior distribution and its complexity. The complexity is measured by the Ku...

Design criteria for a data base management system for a PACS at Georgetown University Hospital

International Nuclear Information System (INIS)

Fahey, F.H.; Wang, P.C.; Mun, S.K.; Choyke, P.L.; Benson, H.R.; Duerinckx, A.; Elliott, L.P.

1986-01-01

A major goal of a radiologic picture archival and communication system (PACS) is to increase the availability of the data to the users who require access to them. This is done by providing the data in a digital form which can be readily communicated and archived. In this manner, the PACS can be seen as a specific example of a data base managements system (DBMS). The PACS/DBMS should organize the data base in such a way as to provide its users with the data they require in a timely and efficient manner. The ability to integrate the variety of data into common data base should lead to a more complete and relevant representation of the available information. A PACS/DBMS is not only unique in the types of data contained in the data base and its different users but also in the volume of data that are entered into the system and transferred within the system each day. Consideration of these characteristics leads to the definition of functional criteria for the PACS/DBMS. This report discusses the criteria that will be used in the design of a DBMS for a PACS at Georgetown University Hospital. (Auth.)

Peligros del átomo pacífico

Directory of Open Access Journals (Sweden)

Juan Zarco de Gea

1962-07-01

Full Text Available Expuestas en el artículo anterior las ventajas que el hombre puede obtener del uso de la energía atómica para fines pacíficos: industria, agricultura, medicina, investigación científica, etc., parece oportuno examinar ahora el reverso de la medalla y estudiar los inconvenientes de ese mismo uso pacífico de las fuerzas atómicas; inconvenientes, dicho sea de paso, que también existen en el aprovechamiento de otras fuerzas naturales, físicas o químicas, en las minas, fábricas, laboratorios y otras muchas empresas de toda índole; pero tratándose de las energías nucleares entran en juego factores nuevos y especiales, que llevan el asunto a terrenos diferentes: moral, político, de salud pública, etc.

Bibliographic database of PACS-related articles from the SPIE literature

Science.gov (United States)

Shile, Peter E.; Freiermuth, Jennifer

1996-05-01

Publications of the International Society of Optical Engineering (SPIE) contain much of the relevant literature on Picture Archiving and Communications Systems (PACS) and related topics. In fact, many PACS-related articles indexed by the National Library of Medicine contain references to articles published by SPIE. Unfortunately, SPIE publications themselves are not indexed by the National Library of Medicine and thus can not be identified through Medline. The lack of a convenient mechanism for searching the SPIE literature is problematic for researchers in medical imaging. With the recent introduction on SPIE's Internet server of their Abstracts Online service and their In-CiteTM title and author searching software, the SPIE literature has become more accessible. However, the searching process is still a cumbersome and time consuming process, and it is not possible to perform key word searches of manuscript abstracts. In this paper we present results of our work on developing a mechanism to more thoroughly search SPIE publications for PACS-related articles.

High-surface-area active carbon

International Nuclear Information System (INIS)

O'Grady, T.M.; Wennerberg, A.N.

1986-01-01

This paper describes the preparation and properties of a unique active carbon having exceptionally high surface areas, over 2500 m 2 /gm, and extraordinary adsorptive capacities. The carbon is made by a direct chemical activation route in which petroleum coke or other carbonaceous sources are reacted with excess potassium hydroxide at 400 0 to 500 0 C to an intermediate product that is subsequently pyrolyzed at 800 0 to 900 0 C to active carbon containing potassium salts. These are removed by water washing and the carbon is dried to produce a powdered product. A granular carbon can also be made by further processing the powdered carbon by using specialized granulation techniques. Typical properties of the carbon include Iodine Numbers of 3000 to 3600, methylene blue adsorption of 650 to 750 mg/gm, pore volumes of 2.0 to 2.6 cc/gm and less than 3.0% ash. This carbon's high adsorption capacities make it uniquely suited for numerous demanding applications in the medical area, purifications, removal of toxic substances, as catalyst carriers, etc

Irreversible membrane fouling abatement through pre-deposited layer of hierarchical porous carbons

KAUST Repository

Hamad, Juma

2014-11-01

In this work, dual-templated hierarchical porous carbons (HPCs), produced from a coupled ice-hard templating approach, are shown to be a highly effective solution to the commonly occurring problem of irreversible fouling of low-pressure membranes used for pre-treatment in wastewater reuse. For the first time, dual-templated HPCs, along with their respective counterparts - single-templated meso-porous carbon (MPCs) (without macropores) - are tested in terms of their fouling reduction capacity and ability to remove different effluent organic matter fractions present in wastewater and compared with a commercially available powdered activated carbon (PAC). The synthesized HPCs provided exceptional fouling abatement, a 4-fold higher fouling reduction as compared to the previously reported best performing commercial PAC and ~2.5-fold better fouling reduction than their respective mesoporous counterpart. Thus, it is shown that not only mesoporosity, but macroporosity is also necessary to achieve high fouling reduction, thus emphasizing the need for dual templating. In the case of HPCs, the pre-deposition technique is also found to outperform the traditional sorbent-feed mixing approach, mainly in terms of removal of fouling components. Based on their superior performance, a high permeability (ultra-low-pressure) membrane consisting of the synthesized HPC pre-deposited on a large pore size membrane support (0.45μm membrane), is shown to give excellent pre-treatment performance for wastewater reuse application. © 2014 Elsevier Ltd.

Enhanced performance of a submerged membrane bioreactor with powdered activated carbon addition for municipal secondary effluent treatment

Energy Technology Data Exchange (ETDEWEB)

Lin, Hongjun, E-mail: hjlin@zjnu.cn [College of Geography and Environmental Sciences, Zhejiang Normal University, 688 Yingbin Avenue, Jinhua, Zhejiang Province 321004 (China); Wang, Fangyuan; Ding, Linxian; Hong, Huachang [College of Geography and Environmental Sciences, Zhejiang Normal University, 688 Yingbin Avenue, Jinhua, Zhejiang Province 321004 (China); Chen, Jianrong, E-mail: cjr@zjnu.cn [College of Geography and Environmental Sciences, Zhejiang Normal University, 688 Yingbin Avenue, Jinhua, Zhejiang Province 321004 (China); Lu, Xiaofeng [Shanghai Institute of Applied Physics, Chinese Academy of Science, Shanghai 201800 (China)

2011-09-15

Highlights: {yields} The first study to investigate the feasibility of PAC-MBR process treating municipal secondary effluent. {yields} The study revealed that most organics in the secondary effluent were low molecular weight (MW) substances, which could be retained in the reactor and then removed to some extent by PAC-MBR process. {yields} The study suggested that the action of biomass and the PAC is mutual and synergistic. - Abstract: The aim of this study was to investigate the feasibility of PAC-MBR process treating municipal secondary effluent. Two laboratory-scale submerged MBRs (SMBR) with and without PAC addition were continuously operated in parallel for secondary effluent treatment. Approximately 63%TOC, 95% NH{sub 4}{sup +}-N and 98% turbidity in secondary effluent were removed by the PAC-MBR process. Most organics in the secondary effluent were found to be low molecular weight (MW) substances, which could be retained in the reactor and then removed to some extent by using PAC-MBR process. Parallel experiments showed that the addition of PAC significantly increased organic removal and responsible for the largest fraction of organic removal. Membrane fouling analysis showed the enhanced membrane performance in terms of sustainable operational time and filtration resistances by PAC addition. Based on these results, the PAC-MBR process was considered as an attractive option for the reduction of pollutants in secondary effluent.

Enhanced performance of a submerged membrane bioreactor with powdered activated carbon addition for municipal secondary effluent treatment

International Nuclear Information System (INIS)

Lin, Hongjun; Wang, Fangyuan; Ding, Linxian; Hong, Huachang; Chen, Jianrong; Lu, Xiaofeng

2011-01-01

Highlights: → The first study to investigate the feasibility of PAC-MBR process treating municipal secondary effluent. → The study revealed that most organics in the secondary effluent were low molecular weight (MW) substances, which could be retained in the reactor and then removed to some extent by PAC-MBR process. → The study suggested that the action of biomass and the PAC is mutual and synergistic. - Abstract: The aim of this study was to investigate the feasibility of PAC-MBR process treating municipal secondary effluent. Two laboratory-scale submerged MBRs (SMBR) with and without PAC addition were continuously operated in parallel for secondary effluent treatment. Approximately 63%TOC, 95% NH 4 + -N and 98% turbidity in secondary effluent were removed by the PAC-MBR process. Most organics in the secondary effluent were found to be low molecular weight (MW) substances, which could be retained in the reactor and then removed to some extent by using PAC-MBR process. Parallel experiments showed that the addition of PAC significantly increased organic removal and responsible for the largest fraction of organic removal. Membrane fouling analysis showed the enhanced membrane performance in terms of sustainable operational time and filtration resistances by PAC addition. Based on these results, the PAC-MBR process was considered as an attractive option for the reduction of pollutants in secondary effluent.

Performance evaluation of carbon nanotube enhanced membranes for SWRO pretreatment application

KAUST Repository

Lee, Jieun

2016-04-25

Multi-wall carbon nanotube (MWCNT) membrane was tested for SWRO pretreatment. The MWCNT membrane itself showed a superior permeate flux (321.3 LMH/bar), which was 4-times as polyethersulfone ultrafiltration (PES-UF) membrane. Reduction of dissolved organic matter improved to 66% with fewer amounts of powder activated carbon (PAC) (0.5 g/L) in MWCNT membrane filtration maintaining a high permeate flux of 600 LMH/bar. It was due to the increased porosity (84.5%) and hydrophilicity (52.9°) by incorporating MWCNT/polyaniline into PES membrane. Ionic strength affected organic removal in seawater filtration by altering electrostatic interaction between organic matter and surface charge of the positively charged MWCNT membrane.

From international charity to value chain coordinator : The case of the Pueblos en Accion Comunitaria (PAC)

NARCIS (Netherlands)

G.M. Gómez (Georgina)

2011-01-01

markdownabstractThis article describes the activities of The association Pueblos en Acción Comunitaria (PAC) as a model of value chain organization with an entrepreneurial vision and Christian inspiration and enquires in what ways it represents a new model to promote local development and poverty

Sphere-pac fuel development program. First semi-annual progress report, October 1979-March 1980

International Nuclear Information System (INIS)

Felt, R.E.

1980-05-01

Development of processes by Exxon Nuclear Company, Inc. for fabricating spherical particle nuclear fuel (sphere-pac) during October 1979 through March 1980 is reported. The program surveyed available technology to develop an initial flowsheet as a design basis for process development. An 0.1 ton/day pilot plant was built to develop and demonstrate the fabrication of sphere-pac fuel. Process and equipment efforts have been directed towards the demonstration of processes and equipment necessary to fabricate sphere-pac fuel on a commercial scale

Improving biomass-derived carbon by activation with nitrogen and cobalt for supercapacitors and oxygen reduction reaction

Science.gov (United States)

Zhang, Man; Jin, Xin; Wang, Linan; Sun, Mengjia; Tang, Yang; Chen, Yongmei; Sun, Yanzhi; Yang, Xiaojin; Wan, Pingyu

2017-07-01

Biomass-derived carbon by activation with nitrogen and cobalt (denoted as NPACCo) was prepared by one-pot pyrolysis of pomelo peel with melamine, cobalt nitrate and potassium hydroxide, followed by acid leaching. NPACCo possesses high content of quaternary-N (2.5%) and pyridinic-N (1.7%), co-existences of amorphous and short-range ordered carbon, high specific surface area and pore structure with majority of micropores and small mesopores. As electrode material of supercapacitors, NPACCo exhibits high specific capacitance and good rate capability. At ultrahigh rate of 50 A g-1 (135 mA cm-2), the capacitance of NPACCo remains 246 F g-1, which is 6.3, 1.9 and 3.2 times as high as that of other three materials (PC, PAC and NPAC). The as-assembled symmetric supercapacitor of NPACCo delivers high energy density, high power density and excellent cycling stability. With respect to oxygen reduction reaction (ORR), NPACCo exhibits high onset potential (0.87 V), high half-wave potential (0.78 V), excellent methanol tolerance and low yield of H2O2. The ORR properties of NPACCo are comparable or superior to those of commercial Pt/C. This investigation of pomelo peel-based NPACCo would be valuable for development of both supercapacitor and ORR.

Merits of usability testing for PACS selection

NARCIS (Netherlands)

Jorritsma, Wiard; Cnossen, Fokie; van Ooijen, Peter M. A.

Objectives: To compare the usability of different Picture Archiving and Communication System (PACS) workstations, determine whether a usability test has added value with respect to the traditional way of comparing PACSs based on functional requirements, and to evaluate the appropriateness of a

Internationalization of healthcare applications: a generic approach for PACS workstations.

Science.gov (United States)

Hussein, R; Engelmann, U; Schroeter, A; Meinzer, H P

2004-01-01

Along with the revolution of information technology and the increasing use of computers world-wide, software providers recognize the emerging need for internationalized, or global, software applications. The importance of internationalization comes from its benefits such as addressing a broader audience, making the software applications more accessible, easier to use, more flexible to support and providing users with more consistent information. In addition, some governmental agencies, e.g., in Spain, accept only fully localized software. Although the healthcare communication standards, namely, Digital Imaging and Communication in Medicine (DICOM) and Health Level Seven (HL7) support wide areas of internationalization, most of the implementers are still protective about supporting the complex languages. This paper describes a generic internationalization approach for Picture Archiving and Communication System (PACS) workstations. The Unicode standard is used to internationalize the application user interface. An encoding converter was developed to encode and decode the data between the rendering module (in Unicode encoding) and the DICOM data (in ISO 8859 encoding). An integration gateway was required to integrate the internationalized PACS components with the different PACS installations. To introduce a pragmatic example, the described approach was applied to the CHILI PACS workstation. The approach has enabled the application to handle the different internationalization aspects transparently, such as supporting complex languages, switching between different languages at runtime, and supporting multilingual clinical reports. In the healthcare enterprises, internationalized applications play an essential role in supporting a seamless flow of information between the heterogeneous multivendor information systems.

Refinement of atomic position in purely ionic materials using PAC spectroscopy

International Nuclear Information System (INIS)

Eslami, E.; Saramad, S.; Moussavi-Zarandi, A.

2000-01-01

In pure ionic solids by means of electric field gradients at substitutional radioactive probe the positions of all atoms in the unit cell can be determined by PAC method with an accuracy of 0.3 Pm which is typically 5 times better than the data available from X ray and neutron diffraction experiments. In the case of oxides where to our knowledge no diffraction analysis exists, the PAC analysis predicts the atomic parameters

Highly porous activated carbons prepared from carbon rich Mongolian anthracite by direct NaOH activation

Energy Technology Data Exchange (ETDEWEB)

Byamba-Ochir, Narandalai [School of Chemical Engineering, Chonnam National University, 77 Yongbong-Ro, Gwangju 61186 (Korea, Republic of); Shim, Wang Geun [Department of Polymer Science and Engineering, Sunchon National University, 255 Jungang-Ro, Suncheon, Jeollanam-Do 57922 (Korea, Republic of); Balathanigaimani, M.S., E-mail: msbala@rgipt.ac.in [Department of Chemical Engineering, Rajiv Gandhi Institute of Petroleum Technology, Ratapur Chowk, Rae Bareli, 229316 Uttar Pradesh (India); Moon, Hee, E-mail: hmoon@jnu.ac.kr [School of Chemical Engineering, Chonnam National University, 77 Yongbong-Ro, Gwangju 61186 (Korea, Republic of)

2016-08-30

Highlights: • Highly porous carbon materials from Mongolian anthracite by chemical activation. • Cheaper and eco-friendly activation process has been employed. • Activated carbons with graphitic structure and energetically heterogeneous surface. • Surface hydrophobicity and porosity of the activated carbons can be controlled. - Abstract: Highly porous activated carbons (ACs) were prepared from Mongolian raw anthracite (MRA) using sodium hydroxide as an activation agent by varying the mass ratio (powdered MRA/NaOH) as well as the mixing method of chemical agent and powdered MRA. The specific BET surface area and total pore volume of the prepared MRA-based activated carbons (MACs) are in the range of 816–2063 m{sup 2}/g and of 0.55–1.61 cm{sup 3}/g, respectively. The pore size distribution of MACs show that most of the pores are in the range from large micropores to small mesopores and their distribution can be controlled by the mass ratio and mixing method of the activating agent. As expected from the intrinsic property of the MRA, the highly graphitic surface morphology of prepared carbons was confirmed from Raman spectra and transmission electron microscopy (TEM) studies. Furthermore the FTIR and XPS results reveal that the preparation of MACs with hydrophobic in nature is highly possible by controlling the mixing conditions of activating agent and powdered MRA. Based on all the results, it is suggested that the prepared MACs could be used for many specific applications, requiring high surface area, optimal pore size distribution, proper surface hydrophobicity as well as strong physical strength.

In vivo biological evaluation of 131I radiolabeled-paclitaxel glucuronide (131I-PAC-G)

International Nuclear Information System (INIS)

Aslan, O.; Biber Muftuler, F.Z.; Yurt Kilcar, A.; Ichedef, C.; Unak, P.

2012-01-01

Paclitaxel (PAC) is a natural occurring diterpene alkoloid originally isolated from the bark of Taxus Brevifolia. It is one of the most important antitumor agents for clinical treatment of ovarian, breast non-small cell lung and prostate cancers. It is known that these types of cancer cells have high β-glucuronidase enzyme which can catalyze the hydrolysis of glucuronides. This is why the synthesis compounds which undergo glucuronidation come into question in the imaging and therapy of these cancer cells. The aim of current study is conjugation of glucuronic acid (G) to the starting substance PAC, labeling with 131 I and to perform its in vivo biological evaluation. Glucuronic acid derived paclitaxel compound [paclitaxel-glucuronide (PAC-G)] was labeled with 131 I using iodogen method. According to thin layer radio chromatography (TLRC) method, the radiochemical yield of 131 I-PAC-G was 84.30 ± 7.40% (n=10). The biodistribution of 131 I-PAC-G in healthy female and male Wistar Albino rats has been investigated. Imaging studies on male Balb-C mice were performed by using the Kodak FX PRO in vivo Imaging System. The range of the breast/blood, breast/muscle; ovary/blood, ovary/muscle ratios is approximately between 1.29 and 11.34 in 240 min, and between 0.71 and 8.24 in 240 min for female rats. The prostate/blood and prostate/muscle ratio is between 1.94 and 6.95 in 30 min for male rats. All these experimental studies indicate that 131 I-PAC-G may potentially be used in breast, ovary and prostate tissues as an imaging agent. Also it is thought that 131 I-PAC-G bears a therapy potential because of the 131 I radionuclide and can be improved with further investigations. (orig.)

Carbon tetrachloride desorption from activated carbon

International Nuclear Information System (INIS)

Jonas, L.A.; Sansone, E.B.

1981-01-01

Carbon tetrachloride was desorbed from a granular activated carbon subsequent to its adsorption under various vapor exposure periods. The varied conditions of exposure resulted in a range of partially saturated carbon beds which, when followed by a constant flow rate for desorption, generated different forms of the desorbing concentration versus time curve. A method of analyzing the desorption curves is presented which permits extraction of the various desorbing rates from the different desorption and to relate this to the time required for such regeneration. The Wheeler desorption kinetic equation was used to calculate the pseudo first order desorption rate constant for the carbon. The desorption rate constant was found to increase monotonically with increasing saturation of the bed, permitting the calculation of the maximum desorption rate constant for the carbon at 100% saturation. The Retentivity Index of the carbon, defined as the dimensionless ratio of the adsorption to the desorption rate constant, was found to be 681

Introduction to PAC/PAD

International Nuclear Information System (INIS)

Mahnke, H.E.

1988-01-01

Both methods, Perturbed Angular Correlation (PAC) utilizing radioactive probes and Perturbed Angular Distribution (PAD) following nuclear reactions measure hyperfine interaction parameters and allow to study magnetism on a rather local scale. While both techniques are based on the same theory the underlying concepts are quite different. Examples on local moments, influence of the nearest-neighbor to the magnetic field in ferromagnets, knight shift in nonmagnetic materials, and magnetism in high-temperature superconductors and related oxides illustrate the recent developments within the methods and the improvements in their sensitivity and resolution. (orig.)

The potential of the innovative SeMPAC process for enhancing the removal of recalcitrant organic micropollutants

Energy Technology Data Exchange (ETDEWEB)

Alvarino, T., E-mail: teresa.alvarino@usc.es [Department of Chemical Engineering, Institute of Technology, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain); Komesli, O. [Ataturk University, Department of Environmental Engineering, 25250 Erzurum (Turkey); Middle East Technical University, Department of Environmental Engineering, 06531 Ankara (Turkey); Suarez, S., E-mail: sonia.suarez@usc.es [Department of Chemical Engineering, Institute of Technology, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain); Lema, J.M., E-mail: juan.lema@usc.es [Department of Chemical Engineering, Institute of Technology, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain); Omil, F., E-mail: francisco.omil@usc.es [Department of Chemical Engineering, Institute of Technology, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain)

2016-05-05

Highlights: • Complete OMPs mass balance in a combined system biological treatment plus PAC. • Improvement of the denitrification after PAC addition. • Enhancement of OMPs biotransformation after PAC addition. • Relation between hydrophobicity (log D) and sorption onto the PAC. • Progressive saturation of the activated carbon in the solid phase with the time. - Abstract: SeMPAC is an innovative process based on a membrane sequential batch reactor to which powdered activated carbon (PAC) is directly added. It was developed with the aim of obtaining a high quality effluent in terms of conventional pollutants and organic micropollutants (OMPs). High COD removal and nitrification efficiencies (>95%) were obtained already during the operation without PAC, although denitrification was enhanced by PAC addition. OMPs were followed in the solid and liquid matrixes so that biotransformation, sorption onto the sludge and adsorption onto the PAC could be assessed. Recalcitrant compounds, such as carbamazepine and diazepam, were readily removed only after PAC addition (>99%). Progressive saturation of PAC was observed, with increasing concentrations of OMPs in the solid phase. Removal efficiencies for recalcitrant compounds were used as indicators for new additions of PAC. An improvement in the moderately biodegradable OMPs removal was observed after PAC addition (e.g. fluoxetine, trimethoprim) which was attributed to the biofilm that grew onto the sorbent, as well as to adsorption onto PAC.

Archival storage solutions for PACS

Science.gov (United States)

Chunn, Timothy

1997-05-01

While they are many, one of the inhibitors to the wide spread diffusion of PACS systems has been robust, cost effective digital archive storage solutions. Moreover, an automated Nearline solution is key to a central, sharable data repository, enabling many applications such as PACS, telemedicine and teleradiology, and information warehousing and data mining for research such as patient outcome analysis. Selecting the right solution depends on a number of factors: capacity requirements, write and retrieval performance requirements, scaleability in capacity and performance, configuration architecture and flexibility, subsystem availability and reliability, security requirements, system cost, achievable benefits and cost savings, investment protection, strategic fit and more.This paper addresses many of these issues. It compares and positions optical disk and magnetic tape technologies, which are the predominant archive mediums today. Price and performance comparisons will be made at different archive capacities, plus the effect of file size on storage system throughput will be analyzed. The concept of automated migration of images from high performance, high cost storage devices to high capacity, low cost storage devices will be introduced as a viable way to minimize overall storage costs for an archive. The concept of access density will also be introduced and applied to the selection of the most cost effective archive solution.

A conceptual study on the formulation of a permeable reactive pavement with activated carbon additives for controlling the fate of non-point source environmental organic contaminants.

Science.gov (United States)

Huang, Shengyi; Liang, Chenju

2018-02-01

To take advantage of the road pavement network where non-point source (NPS) pollution such as benzene, toluene, ethyl-benzene, and xylene (BTEX) from vehicle traffic exhaust via wet and dry atmospheric deposition occurs, the asphalt pavement may be used as a media to control the NPS pollution. An experiment to prepare an adsorptive porous reactive pavement (PRP) was initiated to explore the potential to reduce environmental NPS vehicle pollution. The PRP was prepared and studied as follows: various activated carbons (AC) were initially screened to determine if they were suitable as an additive in the porous asphalt mixture; various mixtures of a selected AC were incorporated with the design of porous asphalt concrete (PAC) to produce PRP, and the PRP formulations were tested to ensure that they comply with the required specifications; qualified specimens were subsequently tested to determine their adsorption capacity for BTEX in aqueous solution, as compared to conventional PAC. The PRP08 and PRP16 samples, named for the design formulations of 0.8% and 1.6% of AC (by wt. in the formulation), exhibited low asphalt drain-down and low abrasion loss and also met all regulated specifications. The BTEX adsorption capacity measurements of PRP08 and PRP16 were 33-46%, 36-51%, 20-22%, and 6-8% respectively, higher than those obtained from PACs. Based on the test results, PRPs showed good physical performance and adsorption and may be considered as a potential method for controlling the transport of NPS vehicle pollutants. Copyright © 2017 Elsevier Ltd. All rights reserved.

Study of Radiologic Technologists' Perceptions of Picture Archiving and Communication System (PACS) Competence and Educational Issues in Western Australia.

Science.gov (United States)

Floyd, Daniel M; Trepp, Errol R; Ipaki, Maryam; Ng, Curtise K C

2015-06-01

Although the implementation of picture archiving and communication system (PACS) could increase productivity of radiology departments, this depends on factors such as the PACS competence of radiologic technologists (RTs). The purpose of this study was to investigate the RTs' perceptions of PACS competence and educational issues in Western Australia (WA). A hardcopy questionnaire was distributed to WA RTs for obtaining their perceptions of PACS competence and educational issues. Descriptive (percentage of frequency, mean and standard deviation) and inferential statistics (t test and analysis of variance) were used to analyze the responses of the multiple choice and five-point scale questions from the returned questionnaires. The questionnaire response rate was 57.7% (173 out of 300). The mean values of all PACS competence questions except questions 2e-g are in the range of 3.9-4.9, i.e., around competent to very competent. Participants indicated they received adequate PACS training (mean 3.8). Statistically significant variables influencing RTs' perceptions of their PACS competence and educational issues including the age (p education received (p system, and received adequate training. However, future PACS education programs should be tailored to different RTs' groups. For example, multiple training modules might be necessary to support the PACS competence development of older RTs and those with lower general computer literacy.

Reasons for Picture Archiving and Communication System (PACS ...

African Journals Online (AJOL)

Tintswalo Brenda Mahlaola

Background: The Picture Archiving and Communication System (PACS) has led to an in- ... incidents in which sensitive information was intentionally shared via social media. .... confidentiality of electronic data in terms of medical ethics,.

Adsorption characteristics of activated carbon hollow fibers

Directory of Open Access Journals (Sweden)

B. V. Kaludjerović

2009-01-01

Full Text Available Carbon hollow fibers were prepared with regenerated cellulose or polysulfone hollow fibers by chemical activation using sodium phosphate dibasic followed by the carbonization process. The activation process increases the adsorption properties of fibers which is more prominent for active carbone fibers obtained from the cellulose precursor. Chemical activation with sodium phosphate dibasic produces an active carbon material with both mesopores and micropores.

A comparative cost analysis of picture archiving and communications systems (PACS versus conventional radiology in the private sector

Directory of Open Access Journals (Sweden)

Indres Moodley

2015-03-01

Aim: To undertake an incremental cost analysis of PACS compared with conventional radiology to determine productivity gains, if any, at two private hospitals in Durban. Method: An incremental cost analysis for chest radiographs, computed tomography and magnetic resonance imaging brain scans with and without contrast were performed. The overall incremental cost for PACS in comparison with a conventional radiology site was determined. The net present value was also determined to evaluate the capital budgeting requirements for both systems. Results: The incremental cost of both capital and the radiology information system for installing PACS shows an expected increase. The incremental PACS image cost shows a reduction. Conclusion: The study provides a benchmark for the cost incurred when implementing PACS. It also provides a decision framework for radiology departments that plan to introduce PACS and helps to determine the feasibility of its introduction.

Production and characterization of granular activated carbon from activated sludge

Directory of Open Access Journals (Sweden)

Z. Al-Qodah

2009-03-01

Full Text Available In this study, activated sludge was used as a precursor to prepare activated carbon using sulfuric acid as a chemical activation agent. The effect of preparation conditions on the produced activated carbon characteristics as an adsorbent was investigated. The results indicate that the produced activated carbon has a highly porous structure and a specific surface area of 580 m²/g. The FT-IR analysis depicts the presence of a variety of functional groups which explain its improved adsorption behavior against pesticides. The XRD analysis reveals that the produced activated carbon has low content of inorganic constituents compared with the precursor. The adsorption isotherm data were fitted to three adsorption isotherm models and found to closely fit the BET model with R² equal 0.948 at pH 3, indicating a multilayer of pesticide adsorption. The maximum loading capacity of the produced activated carbon was 110 mg pesticides/g adsorbent and was obtained at this pH value. This maximum loading was found experimentally to steeply decrease as the solution pH increases. The obtained results show that activated sludge is a promising low cost precursor for the production of activated carbon.

Structural and adsorptive properties of activated carbons prepared by carbonization and activation of resins.

Science.gov (United States)

Leboda, R; Skubiszewska-Zieba, J; Tomaszewski, W; Gun'ko, V M

2003-07-15

Four activated carbons (S1-S4) possessing different structural characteristics were prepared by carbonization of commercial resins (used for ion exchange) and subsequent activation. Their textural parameters were determined on the basis of nitrogen adsorption-desorption at 77.4 K, analyzed by applying several local and overall adsorption isotherm equations. The nature of carbon surface functionalities was analyzed by FTIR spectroscopy. The GC and solid-phase extraction (SPE) techniques were applied to study the influence of the texture of carbonaceous materials on their adsorptive properties. The adsorption efficiency of synthesized carbons with respect to alkylhalides used as probe compounds in the GC measurements varied over a range from 28% (C(2)H(3)Cl(3)/S2) to 85% (CHBr(3)/S1) depending on the type of adsorbates and adsorbents. The concentrating efficiency of these carbons in SPE of explosive materials changed over a larger range from 12% (trinitroglycerin/S4) and 13% (trinitrotoluene/S2) up to 100% (octogen/S1). Active carbon prepared using Zerolite 225x8 as a precursor demonstrated better results than other carbons in two types of adsorption with average values of the efficiency of 75.4% for explosives and 60.8% for alkylhalides.

Knowledge barriers to PACS adoption and implementation in hospitals.

Science.gov (United States)

Paré, Guy; Trudel, Marie-Claude

2007-01-01

Drawing on the classical theory of diffusion of innovations advanced by Rogers [E.M. Rogers, Diffusion of Innovations, 4th ed., Free Press, New York, NY, 1995] and on the theory of barriers to innovation [P. Attewell, Technology diffusion and organizational learning: the case of business computing. Organ. Sci. 3 (1992) 1-19; H. Tanriverdi, C.S. Iacono, Knowledge barriers to diffusion of telemedicine. Proceedings of the 20th International Conference on Information Systems, Charlotte, NC, 1999, pp. 39-50; S. Nambisan, Y.-M. Wang, Roadblocks to web technology adoption? Commun. ACM, 42 (1) (1999) 98-101], this study seeks a better understanding of challenges faced in PACS implementations in hospitals and of the strategies required to ensure their success. To attain this objective, we describe and analyze the process used to adopt and implement PACS at two Canadian hospitals. Our findings clearly demonstrate the importance of treating any PACS deployment not simply as a rollout of new technology but as a project that will transform the organization. Proponents of these projects must not lose sight of the fact that, even if technological complexity represents a significant issue, it must not garner all the project team's attention. This situation is even more dangerous, inasmuch as the greatest risk to the implementation often lies elsewhere. It would also appear to be crucial to anticipate and address organizational and behavioral challenges from the very first phase of the innovation process, in order to ensure that all participants will be committed to the project. In order to maximize the likelihood of PACS success, it appears crucial to adopt a proactive implementation strategy, one that takes into consideration all the technical, economic, organizational, and human factors, and does so from the first phase of the innovation process.

Authenticity techniques for PACS images and records

Science.gov (United States)

Wong, Stephen T. C.; Abundo, Marco; Huang, H. K.

1995-05-01

Along with the digital radiology environment supported by picture archiving and communication systems (PACS) comes a new problem: How to establish trust in multimedia medical data that exist only in the easily altered memory of a computer. Trust is characterized in terms of integrity and privacy of digital data. Two major self-enforcing techniques can be used to assure the authenticity of electronic images and text -- key-based cryptography and digital time stamping. Key-based cryptography associates the content of an image with the originator using one or two distinct keys and prevents alteration of the document by anyone other than the originator. A digital time stamping algorithm generates a characteristic `digital fingerprint' for the original document using a mathematical hash function, and checks that it has not been modified. This paper discusses these cryptographic algorithms and their appropriateness for a PACS environment. It also presents experimental results of cryptographic algorithms on several imaging modalities.

Adsorção em carvão ativado em pó para remoção de microcistina de água de abastecimento público Powdered activated carbon adsorption for microcystin removal from public water supply

Directory of Open Access Journals (Sweden)

Carla Cristine Müller

2009-03-01

Full Text Available A ocorrência de florações de cianobactérias em mananciais de abastecimento público prejudica a qualidade da água, podendo, inclusive, ocasionar a presença de cianotoxinas. A dificuldade de remover as cianotoxinas da água motivou o presente trabalho, cujo objetivo foi o de avaliar a remoção da cianotoxina microcistina empregando diferentes carvões ativados em pó (CAPs. Os CAPs foram caracterizados quanto ao número de iodo, granulometria, distribuição e volume de poros, além das isotermas de Freundlich. Os resultados mostraram que os CAPs de madeira apresentaram os maiores valores do número de iodo, capacidade máxima adsortiva (qe, máx e volume de microporos secundários e mesoporos. A adequada caracterização do CAP é uma etapa importante na sua aquisição pelas estações de tratamento de água, pois índices isolados podem não avaliar corretamente o CAP.The cyanobacterial bloom's occurrence in sources of public supplying harms water quality, even causing cianotoxins presence. The difficulty of the cianotoxins removal from the water has motivated the present work, which objective was to evaluate the removal of the cianotoxin microcystin through the use of different powdered activated carbons (PACs. The PACs were characterized according to its iodine number, granulometry, distribution and volume of pores, besides the Freundlich isotherms. The results showed that the wood PACs presented the highest values of iodine number, maximum adsorptive capacity (qe, max and volume of secondary micropores and mesoporos. The adequate characterization of the PACs is an important stage in its acquisition by the water treatment plants, because isolated indices can not evaluate the PACs correctly.

PACS or the future of the radiologist's working place

International Nuclear Information System (INIS)

Meyer-Ebrecht, D.

1988-01-01

PACS (picture archiving and communication systems) is a synonym for the replacement of the traditional photographic film by means of technologies that will communicate and store images exclusively in digital form. Digital mass storage will replace the film archives and will be linked to all image sources by means of a data communication network. More significantly, PACS will also introduce a novel type of image-evaluation modality, the diagnostic image work station. Images will be displayed on TV monitors. In addition, a variety of support functions will become available for image handling and processing. The replacement of the light box by a digital work station will definitely cause dramatic changes in the radiologist's work. (orig.) [de

Problems facing the radiologist tendering for a hospital wide PACS system

International Nuclear Information System (INIS)

Pilling, John

1999-01-01

As PACS becomes a reality the practical difficulties of installing the new technology become evident. The practical issues of developing a strategy, understanding the market, writing a business case, and an outline based specification are considered. The complexities of European procurement, the evaluation of responses, the contracting process and the problems of implementation, training, assessing the benefits and foreseeing the problems are covered. Provided there is careful attention to detail a hospital can expect to implement a successful PACS system

Implementation and Validation of PACS Integrated Peer Review for Discrepancy Recording of Radiology Reporting

NARCIS (Netherlands)

Olthof, A. W.; van Ooijen, P. M. A.

The purpose of this work is to demonstrate the possibility of implementation of a PACS-integrated peer review system based on RADPEER T classification providing a step-wise implementation plan utilizing features already present in the standard PACS implementation and without the requirement of

Diagnostic image workstations ofr PACS

International Nuclear Information System (INIS)

Meyer-Ebrecht, D.; Fasel, B.; Dahm, M.; Kaupp, A.; Schilling, R.

1990-01-01

Image workstations will be the 'window' to the complex infrastructure of PACS with its intertwined image modalities (image sources, image data bases and image processing devices) and data processing modalities (patient data bases, departmental and hospital information systems). They will serve for user-to-system dialogues, image display and local processing of data as well as images. Their hardware and software structures have to be optimized towards an efficient throughput and processing of image data. (author). 10 refs

Composite supercapacitor electrodes made of activated carbon ...

Indian Academy of Sciences (India)

carbon/PEDOT:PSS and activated carbon/doped PEDOT. T S SONIA, P A MINI, ... polymeric anodes for organic photovoltaics, light-emitting diodes (Pingree et al ... looked upon are carbon nanotubes (CNTs), graphene and activated carbon.

APPC - A new standardised coding system for trans-organisational PACS retrieval

International Nuclear Information System (INIS)

Fruehwald, F.; Lindner, A.; Mostbeck, G.; Hruby, W.; Fruehwald-Pallamar, J.

2010-01-01

As part of a general strategy to integrate the health care enterprise, Austria plans to connect the Picture Archiving and Communication Systems (PACS) of all radiological institutions into a nationwide network. To facilitate the search for relevant correlative imaging data in the PACS of different organisations, a coding system was compiled for all radiological procedures and necessary anatomical details. This code, called the Austrian PACS Procedure Code (APPC), was granted the status of a standard under HL7. Examples are provided of effective coding and filtering when searching for relevant imaging material using the APPC, as well as the planned process for future adjustments of the APPC. The implementation and how the APPC will fit into the future electronic environment, which will include an electronic health act for all citizens in Austria, are discussed. A comparison to other nationwide electronic health record projects and coding systems is given. Limitations and possible use in physical storage media are contemplated. (orig.)

Medical Data Manager an Interface between PACS and the gLite Data Management System

CERN Document Server

Montagnat, Johan; Texier, Romain; Nienartowicz, Krzysztof; Baud, Jean-Philippe

2008-01-01

The medical imaging community uses the DICOM image format and protocol to store and exchange data. The Medical Data Manager (MDM) is an interface between DICOM compliant systems such as PACS and the EGEE Data Management System. It opens hospital imaging networks to the world scale Grid while protecting sensitive medical data. It can be accessed transparently from any gLite service. It is an important milestone towards adoption of Grid technologies in the medical imaging community. Hospitals continuously produce tremendous amounts of image data that is managed by local PACS (Picture Archiving and Communication Systems). These systems are often limited to a local network access although the community experiences a growing interest for data sharing and remote processing. Indeed, patient data is often spread out different medical data acquisition centers. Furthermore, researchers in the area often need to analyze large populations whose data can be gathered through federations of PACS. Opening PACS to the outer I...

The guarantee of the consistency of patient information through modality worklist among PACS, RIS and imaging equipments

International Nuclear Information System (INIS)

Luo Min; Peng Chenglin; Wang Xiaolin; Luo Song; Lei Wenyong; Wang Kang; Wang Xuejian; Wen Hongyu; Wu Hongxing

2003-01-01

Objective: To realize the consistency of patient information through modality worklist among picture archiving and communication system (PACS), radiology information systems (RIS), and imaging equipments. Methods: Many digital modalities including GE Signa 1.5 T MR system, digital mammography, Agfa digital radiography, computed radiography, GE CT, and etc were installed in our hospital. Since the GE PACS system was in English version, the images were saved and the information was managed to PACS without a truly worklist. Two months later, while still using the previous PACS, the consistency of patient information was resolved through modality worklist by adopting the international advanced approach to realize thread worklist of digital imaging and communication in medicine. The information in Chinese will be transformed into information in English in RIS system and saved as the English information to worklist. Results: After the implementation and integration of PACS and RIS was achieved in my hospital, the consistency of patient information was guaranteed through modality worklist between RIS and imaging equipments and the first-rate effect was acquired. The patient information could be checked, edited, and created by using the Chinese RIS system on all diagnostic workstations. Conclusion: The consistency of patient information through modality worklist was realized among PACS, RIS, and imaging equipments, yet at present, the question of guarantee the consistency of patient information must be thought over in PACS building

Biological activation of carbon filters.

Science.gov (United States)

Seredyńska-Sobecka, Bozena; Tomaszewska, Maria; Janus, Magdalena; Morawski, Antoni W

2006-01-01

To prepare biological activated carbon (BAC), raw surface water was circulated through granular activated carbon (GAC) beds. Biological activity of carbon filters was initiated after about 6 months of filter operation and was confirmed by two methods: measurement of the amount of biomass attached to the carbon and by the fluorescein diacetate (FDA) test. The effect of carbon pre-washing on WG-12 carbon properties was also studied. For this purpose, the nitrogen adsorption isotherms at 77K and Fourier transform-infrared (FT-IR) spectra analyses were performed. Moreover, iodine number, decolorizing power and adsorption properties of carbon in relation to phenol were studied. Analysis of the results revealed that after WG-12 carbon pre-washing its BET surface increased a little, the pH value of the carbon water extract decreased from 11.0 to 9.4, decolorizing power remained at the same level, and the iodine number and phenol adsorption rate increased. In preliminary studies of the ozonation-biofiltration process, a model phenol solution with concentration of approximately 10mg/l was applied. During the ozonation process a dose of 1.64 mg O(3)/mg TOC (total organic carbon) was employed and the contact time was 5 min. Four empty bed contact times (EBCTs) in the range of 2.4-24.0 min were used in the biofiltration experiment. The effectiveness of purification was measured by the following parameters: chemical oxygen demand (COD(Mn)), TOC, phenol concentration and UV(254)-absorbance. The parameters were found to decrease with EBCT.

Study of hyperfine parameters in Co-doped tin dioxide using PAC spectroscopy

International Nuclear Information System (INIS)

Ramos, Juliana M.; Carbonari, Artur W.; Martucci, Thiago; Costa, Messias S.; Saxena, Rajendra N.; Vianden, R.; Kessler, P.; Geruschke, T.; Steffens, M.

2011-01-01

PAC technique has been used to measure the hyperfine interactions in nano-structured powder samples of semiconducting SnO 2 doped with Co. The aim of this work is to compare the results of PAC measurements using two different techniques of introducing the radioactive 111 In probe nuclei in the sample of SnO 2 doped with Co. The perturbed gamma-gamma angular correlation (PAC) spectroscopy is used for the measurements of the magnetic hyperfine field (MHF) and the electric field gradient (EFG) at 111 Cd sites in SnO 2 doped with 1% and 2% Co. The measurement of EFG is used to study the defects introduced in the semiconductor material and also for the identification of different phases formed within the compound. The techniques utilized for introducing the radioactive 111 In in the sample are the ion-implantation using radioactive ion beam of 111 In and the chemical process in which 111 InCl 3 solution is added during the preparation of SnO 2 doped with Co using sol gel method. The ion-implantation of 111 In in SnO 2 doped with Co was carried out using the University of Bonn ion-implanter with beam energy of 160 keV. The PAC measurements were carried out with four BaF 2 detector gamma spectrometer in the temperature range of 10-295 K. The results show no significant difference in the values of hyperfine parameters. Both techniques show practically the same electric quadrupole interaction for the substitutional site. The results were compared with previous PAC and Moessbauer measurements of SnO 2 powder samples using 111 In- 111 Cd probe. (author)

Effect of oxygen plasma treatment on adhesion improvement of Au deposited on Pa-c substrates

International Nuclear Information System (INIS)

Lee, Jeong Hoon; Hwang, Kyo Seon; Kim, Tae Song; Seong, Jin Wook; Yoon, Ki Hyun; Ahn, Sae Young

2004-01-01

Adhesion of gold on parylene C (Pa-c) is a major hurdle in achieving reliable and durable performance for biosensor application due to the hydrophobicity of Pa-c. It is, therefore, imperative to put efforts to improve adhesion between Au and Pa-c. In this reseach, oxygen plasma treatment for adhesion improvement was performed on Pa-c surfaces at various plasma powers and times. To analyze the relation of surface energy and roughness to adhesion promotion, we used several techniques such as contact-angle, surface-energy, surface-roughness, and adhesion analyses. As the oxygen plasma power and time were increased, the surface roughness of Pa-c increased. Also, Au films had larger and more uniform grain sizes as the oxygen plasma power and time were increased. Untreated surfaces revealed a contact angle of 108 .deg. , but the contact angle drastically decreased in the initial stage of oxygen plasma treatment and slowly decreased with increasing power and time to values of 27.3 and 34, respectively. From the adhesion analysis, adhesion was improved as the plasma power or time was increased. The improvement of adhesion is related to an increase in roughness as well as carbonyl groups.

Determination of octanol-water partition coefficients of polar polycyclic aromatic compounds (N-PAC) by high performance liquid chromatography

DEFF Research Database (Denmark)

Helweg, C.; Nielsen, T.; Hansen, P.E.

1997-01-01

Prediction of 1-octanol water partition coefficients for a range of polar N-PAC from HPLC capacity coefficients has been investigated. Two commercially available columns, an ODS column and a Diol column were tested with water-methanol eluents. The best prediction of log K-ow for N-PAC was achieve...... with size and log K-ow for N-PAC was 1.1-1.3 lower than log K-ow for the equivalent PAH. Shielding of the nitrogen atom in the N-PAC compounds caused an increase in log K-ow. (C) 1997 Elsevier Science Ltd....

Surgical PACS for the digital operating room. Systems engineering and specification of user requirements.

Science.gov (United States)

Korb, Werner; Bohn, Stefan; Burgert, Oliver; Dietz, Andreas; Jacobs, Stephan; Falk, Volkmar; Meixensberger, Jürgen; Strauss, Gero; Trantakis, Christos; Lemke, Heinz U

2006-01-01

For better integration of surgical assist systems into the operating room, a common communication and processing plattform that is based on the users needs is needed. The development of such a system, a Surgical Picture Aquisition and Communication System (S-PACS), according the systems engineering cycle is oulined in this paper. The first two steps (concept and specification) for the engineering of the S-PACS are discussed.A method for the systematic integration of the users needs', the Quality Function Deployment (QFD), is presented. The properties of QFD for the underlying problem and first results are discussed. Finally, this leads to a first definition of an S-PACS system.

Activated carbon for incinerator uses

International Nuclear Information System (INIS)

Che Seman Mahmood; Norhayati Alias; Mohd Puad Abu

2002-01-01

This paper reports the development of the activated carbon from palm oil kernel shell for use as absorbent and converter for incinerator gas. The procedure is developed in order to prepare the material in bulk quantity and be used in the incinerator. The effect of the use of activating chemicals, physical activation and the preparation parameter to the quality of the carbon products will be discussed. (Author)

Automatically measuring brain ventricular volume within PACS using artificial intelligence.

Science.gov (United States)

Yepes-Calderon, Fernando; Nelson, Marvin D; McComb, J Gordon

2018-01-01

The picture archiving and communications system (PACS) is currently the standard platform to manage medical images but lacks analytical capabilities. Staying within PACS, the authors have developed an automatic method to retrieve the medical data and access it at a voxel level, decrypted and uncompressed that allows analytical capabilities while not perturbing the system's daily operation. Additionally, the strategy is secure and vendor independent. Cerebral ventricular volume is important for the diagnosis and treatment of many neurological disorders. A significant change in ventricular volume is readily recognized, but subtle changes, especially over longer periods of time, may be difficult to discern. Clinical imaging protocols and parameters are often varied making it difficult to use a general solution with standard segmentation techniques. Presented is a segmentation strategy based on an algorithm that uses four features extracted from the medical images to create a statistical estimator capable of determining ventricular volume. When compared with manual segmentations, the correlation was 94% and holds promise for even better accuracy by incorporating the unlimited data available. The volume of any segmentable structure can be accurately determined utilizing the machine learning strategy presented and runs fully automatically within the PACS.

Design and implementation of disaster recovery and business continuity solution for radiology PACS.

Science.gov (United States)

Mansoori, Bahar; Rosipko, Beverly; Erhard, Karen K; Sunshine, Jeffrey L

2014-02-01

In the digital era of radiology, picture archiving and communication system (PACS) has a pivotal role in retrieving and storing the images. Integration of PACS with all the health care information systems e.g., health information system, radiology information system, and electronic medical record has greatly improved access to patient data at anytime and anywhere throughout the entire enterprise. In such an integrated setting, seamless operation depends critically on maintaining data integrity and continuous access for all. Any failure in hardware or software could interrupt the workflow or data and consequently, would risk serious impact to patient care. Thus, any large-scale PACS now have an indispensable requirement to include deployment of a disaster recovery plan to ensure secure sources of data. This paper presents our experience with designing and implementing a disaster recovery and business continuity plan. The selected architecture with two servers in each site (local and disaster recovery (DR) site) provides four different scenarios to continue running and maintain end user service. The implemented DR at University Hospitals Health System now permits continuous access to the PACS application and its contained images for radiologists, other clinicians, and patients alike.

Interpretation of digital breast tomosynthesis: preliminary study on comparison with picture archiving and communication system (PACS) and dedicated workstation.

Science.gov (United States)

Kim, Young Seon; Chang, Jung Min; Yi, Ann; Shin, Sung Ui; Lee, Myung Eun; Kim, Won Hwa; Cho, Nariya; Moon, Woo Kyung

2017-08-01

To compare the diagnostic accuracy and efficiency in the interpretation of digital breast tomosynthesis (DBT) images using a picture archiving and communication system (PACS) and a dedicated workstation. 97 DBT images obtained for screening or diagnostic purposes were stored in both a workstation and a PACS and evaluated in combination with digital mammography by three independent radiologists retrospectively. Breast Imaging-Reporting and Data System final assessments and likelihood of malignancy (%) were assigned and the interpretation time when using the workstation and PACS was recorded. Receiver operating characteristic curve analysis, sensitivities and specificities were compared with histopathological examination and follow-up data as a reference standard. Area under the receiver operating characteristic curve values for cancer detection (0.839 vs 0.815, p = 0.6375) and sensitivity (81.8% vs 75.8%, p = 0.2188) showed no statistically significant differences between the workstation and PACS. However, specificity was significantly higher when analysing on the workstation than when using PACS (83.7% vs 76.9%, p = 0.009). When evaluating DBT images using PACS, only one case was deemed necessary to be reanalysed using the workstation. The mean time to interpret DBT images on PACS (1.68 min/case) was significantly longer than that to interpret on the workstation (1.35 min/case) (p < 0.0001). Interpretation of DBT images using PACS showed comparable diagnostic performance to a dedicated workstation, even though it required a longer reading time. Advances in knowledge: Interpretation of DBT images using PACS is an alternative to evaluate the images when a dedicated workstation is not available.

Flexural Properties of Activated Carbon Filled Epoxy Nano composites

International Nuclear Information System (INIS)

Khalil, H.P.S.A.; Khalil, H.P.S.A.; Alothman, O.Y.; Paridah, M.T.; Zainudin, E.S.

2014-01-01

Activated carbon (AC) filled epoxy nano composites obtained by mixing the desired amount of nano AC viz., bamboo stem, oil palm empty fruit bunch, and coconut shell from agricultural biomass with the epoxy resin. Flexural properties of activated carbons filled epoxy nano composites with 1 %, and 5 % filler loading were measured. In terms of flexural strength and modulus, a significant increment was observed with addition of 1 % vol and 5 % vol nano-activated carbon as compared to neat epoxy. The effect of activated carbon treated by two chemical agents (potassium hydroxide and phosphoric acid) on the flexural properties of epoxy nano composites were also investigated. Flexural strength of activated carbon-bamboo stem, activated carbon-oil palm, and activated carbon-coconut shell reinforced epoxy nano composites showed almost same value in case of 5 % potassium hydroxide activated carbon. Flexural strength of potassium hydroxide activated carbon-based epoxy nano composites was higher than phosphoric acid activated carbon. The flexural toughness of both the potassium hydroxide and phosphoric acid activated carbon reinforced composites range between 0.79 - 0.92 J. It attributed that developed activated carbon filled epoxy nano composites can be used in different applications. (author)

Economic impact of an integrated RIS/PACS system in a university hospital

International Nuclear Information System (INIS)

Kroeger, M.; Wetekam, V.; Nissen-Meyer, S.; Reiser, M.

1999-01-01

Problem: The goal of the current article is to demonstrate how qualitative and monetary effects resulting from an integrated RIS/PACS installation can be evaluated. Results: The sample analysis of a RIS/PACS solution specially designed for a university hospital demonstrates positive qualitative and monetary effects of the system. Under ideal conditions the payoff time of the investments is reached after 4 years of an assumed 8 years effective life of the system. Furthermore, under conservative assumptions, the risk analysis shows a probability of 0% for realising a negative net present value at the end of the payoff time period. Conclusion: It should be pointed out that the positive result of this sample analysis will not necessarily apply to other clinics or hospitals. However, the same methods may be used for the individual evaluation of the qualitative and monetary effects of a RIS/PACS installation in any clinic. (orig.) [de

Study of hyperfine parameters in Co-doped tin dioxide using PAC spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Ramos, Juliana M.; Carbonari, Artur W.; Martucci, Thiago; Costa, Messias S.; Saxena, Rajendra N. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Vianden, R.; Kessler, P.; Geruschke, T.; Steffens, M., E-mail: vianden@hiskp.uni-bonn.d [Rheinische Friedrich-Wilhelms-Universitaet Bonn (HISKP- Bonn) (Germany). Helmholtz - Institut fuer Strahlen- und Kernphysik

2011-07-01

PAC technique has been used to measure the hyperfine interactions in nano-structured powder samples of semiconducting SnO{sub 2} doped with Co. The aim of this work is to compare the results of PAC measurements using two different techniques of introducing the radioactive {sup 111}In probe nuclei in the sample of SnO{sub 2} doped with Co. The perturbed gamma-gamma angular correlation (PAC) spectroscopy is used for the measurements of the magnetic hyperfine field (MHF) and the electric field gradient (EFG) at {sup 111}Cd sites in SnO{sub 2} doped with 1% and 2% Co. The measurement of EFG is used to study the defects introduced in the semiconductor material and also for the identification of different phases formed within the compound. The techniques utilized for introducing the radioactive {sup 111}In in the sample are the ion-implantation using radioactive ion beam of {sup 111}In and the chemical process in which {sup 111}InCl{sub 3} solution is added during the preparation of SnO{sub 2} doped with Co using sol gel method. The ion-implantation of {sup 111}In in SnO{sub 2} doped with Co was carried out using the University of Bonn ion-implanter with beam energy of 160 keV. The PAC measurements were carried out with four BaF{sub 2} detector gamma spectrometer in the temperature range of 10-295 K. The results show no significant difference in the values of hyperfine parameters. Both techniques show practically the same electric quadrupole interaction for the substitutional site. The results were compared with previous PAC and Moessbauer measurements of SnO{sub 2} powder samples using {sup 111}In-{sup 111}Cd probe. (author)

PACS and the digital storage of medical images

International Nuclear Information System (INIS)

Perry, J.R.; Johnston, R.E.; Pizer, S.M.; Lowendorf, D.D.; Rogers, D.C.; Thompson, B.C.; Parrish, D.M.; Brenton, B.C.; Staab, E.V.

1986-01-01

An application of computers in medicine is developing wherein large amounts of digital information in the form of images must be stored, retrieved, and displayed quickly. In radiology this application most commonly goes by the acronym PACS which stands for picture archival and communications system. Estimates of the storage requirements for radiologic images strongly suggest that we should think in terms of terabytes per year for a 150,000 procedure/year, 600 bed hospital. Transmission of patient image data files (a single X-ray image pair may be 12.6 Mbytes) arouses concern over transmission speeds, user waiting tolerances and a communications standard. An important accord is being reached between users and equipment manufacturers in radiology for a standard communications protocol, called the proposed ACR-NEMA standard. Features of PACS which require high speed computational abilities include a lexicon for report generation and image reconstruction, compression, enhancement and 3D display

Self-immobilization of acidogenic mixed consortia on mesoporous material (SBA-15) and activated carbon to enhance fermentative hydrogen production

Energy Technology Data Exchange (ETDEWEB)

Mohan, S. Venkata; Mohanakrishna, G.; Sarma, P.N. [Bioengineering and Environmental Centre, Indian Institute of Chemical Technology, Hyderabad 500607 (India); Reddy, S. Sreevardhan; Raju, B. David; Rao, K.S. Rama [Catalysis and Physical Chemistry Division, Indian Institute of Chemical Technology, Hyderabad 500607 (India)

2008-11-15

The influence of self-immobilization of enriched acidogenic mixed consortia on fermentative hydrogen (H{sub 2}) production was studied on different supporting materials [SBA-15 (mesoporous) and activated carbon (granular; GAC and powder; PAC)] using chemical wastewater as substrate. Batch fermentation experiments were performed with same substrate at different organic loading rates (OLRs) under acidophilic microenvironment (pH 5.5) and room temperature (28 {+-} 2 C). Experimental data evidenced the effectiveness of attached growth on both the H{sub 2} yields and substrate degradation efficiency, particularly at higher loading rates. Among the three materials evaluated, immobilization on SBA-15 material showed comparatively effective performance in enhancing both H{sub 2} yield and substrate degradation. Suspended growth (SG-control) culture showed inhibition in terms of both H{sub 2} production and substrate degradation especially at applied higher loading rates. Immobilization on SBA-15 resulted in nine times higher H{sub 2} production (7.29 mol/kg COD{sub R}-day at OLR of 0.83 kg COD/m{sup 3}-day) than the lowest yield observed (suspended growth at OLR of 2.55 kg COD/m{sup 3}-day). Maximum substrate degradation rate (SDR) of 0.96 kg COD/m{sup 3}-day (OLR 2.55 kg COD/m{sup 3}-day) was also observed with SBA-15 immobilization, which is 1.62 times higher than the lowest substrate degradation observed with SG-control experiments with the same OLR. Attached growth on GAC and PAC also showed remarkable improvement in the process performance at higher OLRs compared to SG-control. (author)

Pulmonary Artery Catheter (PAC Accuracy and Efficacy Compared with Flow Probe and Transcutaneous Doppler (USCOM: An Ovine Cardiac Output Validation

Directory of Open Access Journals (Sweden)

Robert A. Phillips

2012-01-01

Full Text Available Background. The pulmonary artery catheter (PAC is an accepted clinical method of measuring cardiac output (CO despite no prior validation. The ultrasonic cardiac output monitor (USCOM is a noninvasive alternative to PAC using Doppler ultrasound (CW. We compared PAC and USCOM CO measurements against a gold standard, the aortic flow probe (FP, in sheep at varying outputs. Methods. Ten conscious sheep, with implanted FPs, had measurements of CO by FP, USCOM, and PAC, at rest and during intervention with inotropes and vasopressors. Results. CO measurements by FP, PAC, and USCOM were 4.0±1.2 L/min, 4.8±1.5 L/min, and 4.0±1.4 L/min, respectively, (=280, range 1.9 L/min to 11.7 L/min. Percentage bias and precision between FP and PAC, and FP and USCOM was −17 and 47%, and 1 and 36%, respectively. PAC under-measured Dobutamine-induced CO changes by 20% (relative 66% compared with FP, while USCOM measures varied from FP by 3% (relative 10%. PAC reliably detected −30% but not +40% CO changes, as measured by receiver operating characteristic area under the curve (AUC, while USCOM reliably detected ±5% changes in CO (AUC>0.70. Conclusions. PAC demonstrated poor accuracy and sensitivity as a measure of CO. USCOM provided equivalent measurements to FP across a sixfold range of outputs, reliably detecting ±5% changes.

(PACS) data security breaches: Intentional versus non-intentional ...

African Journals Online (AJOL)

Background: The Picture Archiving and Communication System (PACS) has led to an increase in breached health records and violation of patient confidentiality. The South African constitution makes provision for human dignity and privacy, virtues which confidentiality seeks to preserve. Confidentiality thus constitutes a ...

PENURUNAN TOKSISITAS LEACHATE (AIR LINDI DARI TPAS PUTRI CEMPO MOJOSONGO SURAKARTA DENGAN PAC (POLY ALUMINUM CHLORIDE (Toxicity Reduction of Leachate from Putri Cempo Municipal Landfill (TPAS Mojosongo Surakarta with PAC (Poly Aluminium Chloride

Directory of Open Access Journals (Sweden)

Dwi Astuti

2010-03-01

Full Text Available ABSTRAK Tujuan penelitian ini adalah menetapkan persen penurunan toksisitas sesudah diperlakukan dengan PAC. Rancangan penelitian ini adalah eksperimen murni dengan pretest-posttest with control group design. Populasi dalam penelitian ini adalah air lindi yang berasal dari TPAS Putri Cempo MPAC: 25,06% (24 jam; 21,07% (48 jam; 17,49% (72 jam; dan 14,97% (96 jam. (2 Dengan perlakuan PAC: 89,44% (24 jam; 63,73% (48 jam; 49,99% (72 jam; dan 40,96% (96 jam. Sehingga persentase penurunan toksisitasnya adalah: 64,38% (24 jam, 42,66% (48 jam, 32,50% (72 jam, dan 25,99% (96 jam.    ABSTRACT The aims of the current study were to determine percentage of leachate toxicity reduction after treatment with PAC. The experimental design used was true experimental study with pretest-posttest with control group design. Population in this study was leachate from Putri Cempo Landfill (TPAS Putri Cempo Mojosongo Surakarta. The sample was 250 litres leachate obtained from the landfill outlet by quota sampling method. The results revealed the leachate toxicity based on LC50 24-96 hours were: (1 without PAC treatment: 25.06% (24 hours, 21.07% (48 hours, 17.49% (72 hours, and 14.97% (96 hours; (2 with PAC treatment: 89.44% (24 hours, 63.73% (48 hours, 49.99% (72 hours, and 40.96% (96 hours. Therefore, the toxicity reductions were: 64.38% (24 hours, 42.66% (48 hours, 32.50% (72 hours, and 25.99% (96 hours.

PacIOOS Ocean Gliders: SeaGlider 139: Mission 2

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 139: Mission 7

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 114: Mission 4

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 139: Mission 3

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 523: Mission 1

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 139: Mission 1

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 523: Mission 4

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 139: Mission 6

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 139: Mission 8

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 139: Mission 9

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 523: Mission 3

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

PacIOOS Ocean Gliders: SeaGlider 114: Mission 3

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As a part of PacIOOS, ocean gliders provide very detailed information about the physical and chemical condition of the waters around the Hawaiian Islands....

Activated carbon from peach stones using phosphoric acid activation at medium temperatures.

Science.gov (United States)

Kim, Dong-Su

2004-01-01

In the present study, the activation features of phosphoric acid have been investigated using waste peach stones as the raw material in the production of granular activated carbon. Thermogravimetry/differential thermal analysis was conducted to characterize the thermal behavior of peach stone and titration method was used to evaluate the adsorption capacity of the produced activated carbon. It was observed that the iodine value of the activated carbon increased with activation temperature. However, temperatures higher than 500 degrees C caused a thermal destruction, which resulted in the decrease of the adsorption capacity. Activation longer than 1.5 h at 500 degrees C resulted in thermal degradation of the porous structure of the activated carbon. The adsorption capacity was enhanced with increasing of amounts of phosphoric acid, however, excessive phosphoric acid caused a decrease in the iodine value. In addition, it was found that the carbon yields generally decreased with activation temperature and activation time. Scanning electron microscopy analysis was conducted to observe the changes in the poros structure of the activated carbon produced in different temperatures. Activation of carbon by phosphoric acid was found to be superior to that by CaCl2 and gas activation. The activated carbon produced from peach stone was applied as an adsorbent in the treatment of synthesized wastewater containing cadmium ion and its adsorption capacity was found to be as good as that of the commercial one.

Is PACS feasible for a major department of radiology

International Nuclear Information System (INIS)

Bautz, W.; Kolbe, J.

1986-01-01

Picture Archiving and Communication Systems (PACS) are getting more and more important for Departments of Radiology with the increasing spread of digital imaging methods. To determine the demands made on such systems, we calculated the digital image data volume for all examinations carried out in 1983 at the Department of Medical Radiology of the University of Tuebingen. 20.37% of all examinations were performed with digitalised equipment. Plain radiography takes the lion's share among the total number of image data. If digitalisation is based on a spatial resolution of 8 Lp/mm, the share is 98.4% of the total image data volume of 7123 GByte. This figure is far in excess of the estimates stated in literature. The possibilities of image data reduction and feasibility of a major PACS are discussed. (orig.) [de

Adaptation of the Activity Measure Post-Acute Care (AM-PAC) from English to Mandarin using the dual-panel translation approach

DEFF Research Database (Denmark)

Chang, Feng-Hang; Liou, Tsan-Hon; Brodersen, John

2017-01-01

translated using the dual-panel method. The translated AM-PAC was tested in 550 Chinese-speaking rehabilitation outpatients. Floor and ceiling effects were evaluated and internal consistency was assessed using Cronbach's alpha. Spearman correlation was used to assess the concurrent validity of the AM...

DEVELOPMENT OF ACTIVATED CARBONS FROM COAL COMBUSTION BY-PRODUCTS

Energy Technology Data Exchange (ETDEWEB)

Harold H. Schobert; M. Mercedes Maroto-Valer; Zhe Lu

2003-09-30

The increasing role of coal as a source of energy in the 21st century will demand environmental and cost-effective strategies for the use of coal combustion by-products (CCBPs), mainly unburned carbon in fly ash. Unburned carbon is nowadays regarded as a waste product and its fate is mainly disposal, due to the present lack of efficient routes for its utilization. However, unburned carbon is a potential precursor for the production of adsorbent carbons, since it has gone through a devolatilization process while in the combustor, and therefore, only requires to be activated. Accordingly, the principal objective of this work was to characterize and utilize the unburned carbon in fly ash for the production of activated carbons. The unburned carbon samples were collected from different combustion systems, including pulverized utility boilers, a utility cyclone, a stoker, and a fluidized bed combustor. LOI (loss-on-ignition), proximate, ultimate, and petrographic analyses were conducted, and the surface areas of the samples were characterized by N2 adsorption isotherms at 77K. The LOIs of the unburned carbon samples varied between 21.79-84.52%. The proximate analyses showed that all the samples had very low moisture contents (0.17 to 3.39 wt %), while the volatile matter contents varied between 0.45 to 24.82 wt%. The elemental analyses show that all the unburned carbon samples consist mainly of carbon with very little hydrogen, nitrogen, sulfur and oxygen In addition, the potential use of unburned carbon as precursor for activated carbon (AC) was investigated. Activated carbons with specific surface area up to 1075m{sup 2}/g were produced from the unburned carbon. The porosity of the resultant activated carbons was related to the properties of the unburned carbon feedstock and the activation conditions used. It was found that not all the unburned carbon samples are equally suited for activation, and furthermore, their potential as activated carbons precursors could be

Promoting effect of active carbons on methanol dehydrogenation on sodium carbonate - hydrogen spillover

OpenAIRE

Su, S.; Prairie, M.; Renken, A.

1993-01-01

Methanol dehydrogenation to formaldehyde was conducted in a fixed-bed flow reactor with sodium carbonate catalyst mixed with active carbons or transition metals. The additives promoted the reaction rate at 880-970 K without modifying formaldehyde selectivity. This effect increases with increasing carbon content in the carbon-carbonate mixture. Activation energy of methanol conversion is the same for the mixture and the carbonate alone. Temperature-programmed desorption experiments showed that...

Effect of Poly Aluminium Chloride (PAC) on some blood constituents of Nile Tilapia (Oreochromis niloticus)

International Nuclear Information System (INIS)

Adam, H. M.; Agab, H.

2006-01-01

Poly aluminium chloride (PAC) is an urban drinking water purification substance that was introduced recently in Sudan and used to substitute polymer poly diallyl dimethyl aluminium chloride (DADMAC) and aluminium sulphate in water purification treatments. This study was conducted to determine its effects on fish health, which is is considered a biological indicator and an essential component of fresh water ecosystem. In this experiment, PAC was used in three different concentrations (0.1, 0.2 and 0.3 ml/1) in experimental tanks to achieve the desirable doses for the study. The tanks were populated by Nile Tilapia fingerlings (Oreochromis niloticus) with an average weight ranging between 70 and 100 grams. Exposure of this fish to PAC resulted in an immediate signification reduction (P<0.01) in haemoglobin concentration, erythrocytes count, packed cell volume, mean corpuscular volume and mean corpuscular haemoglobin concentration of experimental fingerlings blood. The degree of reduction in these parameters was directly proportional to the concentration of PAC used. (Author)

Active component modeling for analog integrated circuit design. Model parametrization and implementation in the SPICE-PAC circuit simulator; Modelisation de composants actifs pour la CAO de circuits integres analogiques. Parametrage et implantation de modeles dans le simulateur SPICE-PAC

Energy Technology Data Exchange (ETDEWEB)

Marchal, Xavier

1992-06-19

In order to use CAD efficiently in the analysis and design of electronic Integrated circuits, adequate modeling of active non-linear devices such as MOSFET transistors must be available to the designer. Many mathematical forms can be given to those models, such as explicit relations, or implicit equations to be solved. A major requirement in developing MOS transistor models for IC simulation is the availability of electrical characteristic curves over a wide range of channel width and length, including the sub-micrometer range. To account in a convenient way for bulk charge influence on I{sub DS} = f(V{sub DS}, V{sub GS}, v{sub BS}) device characteristics, all 3 standard SPICE MOS models use an empirical fitting parameter called the 'charge sharing factor'. Unfortunately, this formulation produces models which only describe correctly either some of the short channel phenomena, or some particular operating conditions (low injection, avalanche effect, etc.). We present here a cellular model (CDM = Charge Distributed Model) implemented in the open modular SPICE-PAC Simulator; this model is derived from the 4-terminal WANG charge controlled MOSFET model, using the charge sheet approximation. The CDM model describes device characteristics in ail operating regions without introducing drain current discontinuities and without requiring a 'charge sharing factor'. A usual problem to be faced by designers when they simulate MOS ICs is to find a reliable source of model parameters. Though most models have a physical basis, some of their parameters cannot be easily estimated from physical considerations. It can also happen that physically determined parameters values do not produce a good fit to measured device characteristics. Thus it is generally necessary to extract model parameters from measured transistor data, to ensure that model equations approximate measured curves accurately enough. Model parameters extraction can be done in 2 different ways, exposed in this thesis

In vivo biological evaluation of {sup 131}I radiolabeled-paclitaxel glucuronide ({sup 131}I-PAC-G)

Energy Technology Data Exchange (ETDEWEB)

Aslan, O.; Biber Muftuler, F.Z.; Yurt Kilcar, A.; Ichedef, C.; Unak, P. [Ege Univ., Izmir (Turkey). Dept. of Nuclear Applications

2012-07-01

Paclitaxel (PAC) is a natural occurring diterpene alkoloid originally isolated from the bark of Taxus Brevifolia. It is one of the most important antitumor agents for clinical treatment of ovarian, breast non-small cell lung and prostate cancers. It is known that these types of cancer cells have high {beta}-glucuronidase enzyme which can catalyze the hydrolysis of glucuronides. This is why the synthesis compounds which undergo glucuronidation come into question in the imaging and therapy of these cancer cells. The aim of current study is conjugation of glucuronic acid (G) to the starting substance PAC, labeling with {sup 131}I and to perform its in vivo biological evaluation. Glucuronic acid derived paclitaxel compound [paclitaxel-glucuronide (PAC-G)] was labeled with {sup 131}I using iodogen method. According to thin layer radio chromatography (TLRC) method, the radiochemical yield of {sup 131}I-PAC-G was 84.30 {+-} 7.40% (n=10). The biodistribution of {sup 131}I-PAC-G in healthy female and male Wistar Albino rats has been investigated. Imaging studies on male Balb-C mice were performed by using the Kodak FX PRO in vivo Imaging System. The range of the breast/blood, breast/muscle; ovary/blood, ovary/muscle ratios is approximately between 1.29 and 11.34 in 240 min, and between 0.71 and 8.24 in 240 min for female rats. The prostate/blood and prostate/muscle ratio is between 1.94 and 6.95 in 30 min for male rats. All these experimental studies indicate that {sup 131}I-PAC-G may potentially be used in breast, ovary and prostate tissues as an imaging agent. Also it is thought that {sup 131}I-PAC-G bears a therapy potential because of the {sup 131}I radionuclide and can be improved with further investigations. (orig.)

Development of activated carbon pore structure via physical and chemical activation of biomass fibre waste

International Nuclear Information System (INIS)

Williams, Paul T.; Reed, Anton R.

2006-01-01

Biomass waste in the form of biomass flax fibre, produced as a by-product of the textile industry was processed via both physical and chemical activation to produce activated carbons. The surface area of the physically activated carbons were up to 840 m 2 g -1 and the carbons were of mesoporous structure. Chemical activation using zinc chloride produced high surface area activated carbons up to 2400 m 2 g -1 and the pore size distribution was mainly microporous. However, the process conditions of temperature and zinc chloride concentration could be used to manipulate the surface area and porosity of the carbons to produce microporous, mesoporous and mixed microporous/mesoporous activated carbons. The physically activated carbons were found to be a mixture of Type I and Type IV carbons and the chemically activated carbons were found to be mainly Type I carbons. The development of surface morphology of physically and chemically activated carbons observed via scanning electron microscopy showed that physical activation produced activated carbons with a nodular and pitted surface morphology whereas activated carbons produced through chemical activation had a smooth surface morphology. Transmission electron microscopy analysis could identify mesopore structures in the physically activated carbon and microporous structures in the chemically activated carbons

FUJI - a comparative irradiation test with pellet, sphere-pac, and vipac fuel

International Nuclear Information System (INIS)

Hellwig, C.; Bakker, K.; Ozawa, T.; Nakamura, M.; Kihara, Y.

2004-01-01

Particle fuels such as sphere-pac and vipac fuels have been considered as promising fuel systems for fast reactors, due to their inherent potential in remote operation, cost reduction and incineration of minor actinides or low-decontaminated plutonium. The FUJI test addresses the questions of fabrication of MOX particle fuels with high Pu content (20%) and its irradiation behaviour during the start-up phase. Four kinds of fuel, i.e. MOX sphere-pac, MOX vipac, MOX pellet and Np-MOX sphere-pac fuel, have been and will be simultaneously irradiated under identical conditions in the High Flux Reactor in Petten. First results show that the particle fuel undergoes a dramatic structure change already at the very beginning of the irradiation when the maximum power is reached. The structural changes, i.e. the formation of a central void and the densification of fuel, decrease the fuel central temperature. Thus the fast and strong restructuring helps to prevent central fuel melting at high power levels. (authors)

Application of Nano PAC on Mitigating Membrane Fouling by Surface Properties Optimization

Directory of Open Access Journals (Sweden)

Mi Hairong

2016-01-01

Full Text Available Membrane material has been widely accepted owing to the ability in water treatment, but the membrane fouling problem in using process is seriously restricted the promotion of membrane technology. So in this research nano PAC flocculant is added into the raw water to reach the goals of strengthening treatment efficiency and mitigating membrane fouling. According to the TMP change, it results that the PAC dosage of 45mg/L can realize the purpose to mitigate membrane fouling best. Compared with MBR, the MCBR is 16 days tardiness at the change of TMP, 1/3 gel layer filtration resistance less and 3.5% C element content fewer. The sum of C, O and N elements content, in addition, in the gel layer pollutants is more than 95%. That means membrane pollution is mainly caused by organic matter and nano PAC has the effect on surface properties optimization and membrane fouling mitigating.

Using an open-source PACS virtual machine for a digital angiography unit: methods and initial impressions.

Science.gov (United States)

Kagadis, George C; Alexakos, Christos; Langer, Steve G; French, Todd

2012-02-01

The productivity gains, diagnostic benefit, and enhanced data availability to clinicians enabled by picture archiving and communication systems (PACS) are no longer in doubt. However, commercial PACS offerings are often extremely expensive initially and require ongoing support contracts with vendors to maintain them. Recently, several open-source offerings have become available that put PACS within reach of more users. However, they can be resource-intensive to install and assure that they have room for future growth--both for computational and storage capacity. An alternate approach, which we describe herein, is to use PACS built on virtual machines which can be moved from smaller to larger hardware as needed in a just-in-time manner. This leverages the cost benefits of Moore's Law for both storage and compute costs. We describe the approach and current results in this paper.

Making Activated Carbon by Wet Pressurized Pyrolysis

Science.gov (United States)

Fisher, John W.; Pisharody, Suresh; Wignarajah, K.; Moran, Mark

2006-01-01

A wet pressurized pyrolysis (wet carbonization) process has been invented as a means of producing activated carbon from a wide variety of inedible biomass consisting principally of plant wastes. The principal intended use of this activated carbon is room-temperature adsorption of pollutant gases from cooled incinerator exhaust streams. Activated carbon is highly porous and has a large surface area. The surface area depends strongly on the raw material and the production process. Coconut shells and bituminous coal are the primary raw materials that, until now, were converted into activated carbon of commercially acceptable quality by use of traditional production processes that involve activation by use of steam or carbon dioxide. In the wet pressurized pyrolysis process, the plant material is subjected to high pressure and temperature in an aqueous medium in the absence of oxygen for a specified amount of time to break carbon-oxygen bonds in the organic material and modify the structure of the material to obtain large surface area. Plant materials that have been used in demonstrations of the process include inedible parts of wheat, rice, potato, soybean, and tomato plants. The raw plant material is ground and mixed with a specified proportion of water. The mixture is placed in a stirred autoclave, wherein it is pyrolized at a temperature between 450 and 590 F (approximately between 230 and 310 C) and a pressure between 1 and 1.4 kpsi (approximately between 7 and 10 MPa) for a time between 5 minutes and 1 hour. The solid fraction remaining after wet carbonization is dried, then activated at a temperature of 500 F (260 C) in nitrogen gas. The activated carbon thus produced is comparable to commercial activated carbon. It can be used to adsorb oxides of sulfur, oxides of nitrogen, and trace amounts of hydrocarbons, any or all of which can be present in flue gas. Alternatively, the dried solid fraction can be used, even without the activation treatment, to absorb

Evaluation of single-step steam pyrolysis-activated carbons

African Journals Online (AJOL)

Mgina

Activated carbon has been widely used worldwide as an effective filtration or adsorption ... of producing activated carbon (AC) from local agroforestry residues by ..... impurities from waste water. .... Production of granular activated carbon.

PacIOOS Nearshore Sensor 06 (NS06): Pohnpei, Micronesia

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The nearshore sensors are part of the Pacific Islands Ocean Observing System (PacIOOS) and are designed to measure a variety of ocean parameters at fixed point...

PacIOOS Nearshore Sensor 08 (NS08): Koror, Palau

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The nearshore sensors are part of the Pacific Islands Ocean Observing System (PacIOOS) and are designed to measure a variety of ocean parameters at fixed point...

PacIOOS Nearshore Sensor 11 (NS11): Saipan, CNMI

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The nearshore sensors are part of the Pacific Islands Ocean Observing System (PacIOOS) and are designed to measure a variety of ocean parameters at fixed point...

Remote consultation and diagnosis in medical imaging using a global PACS backbone network

Science.gov (United States)

Martinez, Ralph; Sutaria, Bijal N.; Kim, Jinman; Nam, Jiseung

1993-10-01

A Global PACS is a national network which interconnects several PACS networks at medical and hospital complexes using a national backbone network. A Global PACS environment enables new and beneficial operations between radiologists and physicians, when they are located in different geographical locations. One operation allows the radiologist to view the same image folder at both Local and Remote sites so that a diagnosis can be performed. The paper describes the user interface, database management, and network communication software which has been developed in the Computer Engineering Research Laboratory and Radiology Research Laboratory. Specifically, a design for a file management system in a distributed environment is presented. In the remote consultation and diagnosis operation, a set of images is requested from the database archive system and sent to the Local and Remote workstation sites on the Global PACS network. Viewing the same images, the radiologists use pointing overlay commands, or frames to point out features on the images. Each workstation transfers these frames, to the other workstation, so that an interactive session for diagnosis takes place. In this phase, we use fixed frames and variable size frames, used to outline an object. The data pockets for these frames traverses the national backbone in real-time. We accomplish this feature by using TCP/IP protocol sockets for communications. The remote consultation and diagnosis operation has been tested in real-time between the University Medical Center and the Bowman Gray School of Medicine at Wake Forest University, over the Internet. In this paper, we show the feasibility of the operation in a Global PACS environment. Future improvements to the system will include real-time voice and interactive compressed video scenarios.

Toshiba General Hospital PACS for routine in- and outpatient clinics

Science.gov (United States)

Toshimitsu, Akihiro; Okazaki, Nobuo; Kura, Hiroyuki; Nishihara, Eitaro; Tsubura, Shinichi

1996-05-01

The Toshiba General Hospital introduced a departmental RIS/PACS (Radiology Information System/Picture Archiving and Communication System) in the radiology department in May, 1993. It has been used routinely since that time. In order to provide efficient means for clinicians to find and read many images, the system has been expanded to the neurosurgery and urology clinics and wards since May, 1995, and five image referring workstations now provide digital images to clinicians. In this paper we discuss an algorithm for image migration, one of the key issues to accomplish the expansion to outpatient clinics successfully, and propose the WYWIWYG (what you want is what you get) image transfer logic. This is the logic used to transfer images that physicians require refer without increasing the traffic between the image server and referring workstations. We accomplish the WYWIWYG logic by prioritizing exams the physicians have not yet viewed and by finding historical exams according to the modality, anatomy, and marking. Clinicians gave us comments from their first use of the system and suggested that the PACS enables clinicians to review images more efficiently compared to a film-based system. Our experience suggests that it is a key to the effective application of PACS in outpatient clinics to incorporate consideration patterns of clinicians on the migration algorithm.

Estado del Medio Ambiente Marino y Costero del Pacífico Sudeste.

OpenAIRE

Andrade V., Héctor; Guitiérres S., Sixto; Andrade C., Héctor

2014-01-01

El presente documento contiene los antecedentes sistematizados sobre el Estado del Medio Ambiente Marino Costero del Pacífico Sudeste en base a los informes nacionales de consultoría elaborados entre 2011 y 2012 en Panamá, Colombia, Ecuador, Perú y Chile y cuya finalidad fue establecer un estado actualizado del medio marino a nivel regional, en el marco del Programa CONPACSE III de la Comisión Permanente de Pacífico Sur. Los principales contaminantes presentes en las aguas marinas costeras de...

Manual sobre el desarrollo integral de la Cuenca Pacífica Colombiana

OpenAIRE

Cardona, Jose Gerardo

2010-01-01

En el presente documento nos ocupamos en trazar las pautas que consideramos deben seguirse para los trabajos de investigación científica y tecnológica, indispensables para los programas de desarrollo agroforestal y pecuario de la Cuenca del Pacífico Colombiano; advirtiendo que nuestras sugerencias no tienen carácter dogmático, sencillamente constituyen, a nuestro juicio, complemento al diagnóstico y propuestas consignados en el Manual Nº 1 El Litoral Pacífico Colombiano, referentes a los sect...

Activation and micropore structure determination of activated carbon-fiber composites

Energy Technology Data Exchange (ETDEWEB)

Jagtoyen, M.; Derbyshire, F.; Kimber, G. [Univ. of Kentucky, Lexington, KY (United States). Center for Applied Energy Research

1997-09-05

Rigid, high surface area activated carbon fiber composites have been produced with high permeabilities for environmental applications in gas and water purification. These novel monolithic adsorbents can be produced in single pieces to a given size and shape. The project involves a collaboration between the Oak Ridge National Laboratory (ORNL) and the Center for Applied Energy Research (CAER), University of Kentucky. The carbon fiber composites are produced at the ORNL and activated at the CAER using different methods, with the aims of producing a uniform degree of activation, and of closely controlling pore structure and adsorptive properties. The main focus of the present work has been to find a satisfactory means to uniformly activate large samples of carbon fiber composites and produce controlled pore structures. Several environmental applications have been explored for the activated carbon fiber composites. One of these was to evaluate the activated composites for the separation of CH{sub 4}-CO{sub 2} mixtures, and an apparatus was constructed specifically for this purpose. The composites were further evaluated in the cyclic recovery of volatile organics. The activated carbon fiber composites have also been tested for possible water treatment applications by studying the adsorption of sodium pentachlorophenolate, PCP.

A novel activated carbon for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Shen, Haijie [Key Laboratory of Environmentally Friendly Chemistry and Applications of Ministry of Education, College of Chemistry, Xiangtan University, Hunan 411105 (China); Liu, Enhui, E-mail: liuenhui99@sina.com.cn [Key Laboratory of Environmentally Friendly Chemistry and Applications of Ministry of Education, College of Chemistry, Xiangtan University, Hunan 411105 (China); Xiang, Xiaoxia; Huang, Zhengzheng; Tian, Yingying; Wu, Yuhu; Wu, Zhilian; Xie, Hui [Key Laboratory of Environmentally Friendly Chemistry and Applications of Ministry of Education, College of Chemistry, Xiangtan University, Hunan 411105 (China)

2012-03-15

Highlights: Black-Right-Pointing-Pointer A novel activated carbon was prepared from phenol-melamine-formaldehyde resin. Black-Right-Pointing-Pointer The carbon has large surface area with microporous, and high heteroatom content. Black-Right-Pointing-Pointer Heteroatom-containing functional groups can improve the pseudo-capacitance. Black-Right-Pointing-Pointer Physical and chemical properties lead to the good electrochemical properties. -- Abstract: A novel activated carbon has been prepared by simple carbonization and activation of phenol-melamine-formaldehyde resin which is synthesized by the condensation polymerization method. The morphology, thermal stability, surface area, elemental composition and surface chemical composition of samples have been investigated by scanning electron microscope, thermogravimetry and differential thermal analysis, Brunauer-Emmett-Teller measurement, elemental analysis and X-ray photoelectron spectroscopy, respectively. Electrochemical properties have been studied by cyclic voltammograms, galvanostatic charge/discharge, and electrochemical impedance spectroscopy measurements in 6 mol L{sup -1} potassium hydroxide. The activated carbon shows good capacitive behavior and the specific capacitance is up to 210 F g{sup -1}, which indicates that it may be a promising candidate for supercapacitors.

Fitting PAC spectra with a hybrid algorithm

Energy Technology Data Exchange (ETDEWEB)

Alves, M. A., E-mail: mauro@sepn.org [Instituto de Aeronautica e Espaco (Brazil); Carbonari, A. W., E-mail: carbonar@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (Brazil)

2008-01-15

A hybrid algorithm (HA) that blends features of genetic algorithms (GA) and simulated annealing (SA) was implemented for simultaneous fits of perturbed angular correlation (PAC) spectra. The main characteristic of the HA is the incorporation of a selection criterion based on SA into the basic structure of GA. The results obtained with the HA compare favorably with fits performed with conventional methods.

Measurement of carbon thermodynamic activity in sodium

Energy Technology Data Exchange (ETDEWEB)

Kozlov, F A; Zagorulko, Yu I; Kovalev, Yu P; Alekseev, V V [Institute of Physics and Power Engineering, Obninsk (USSR)

1980-05-01

The report presents the brief outline on system of carbon activity detecting system in sodium (SCD), operating on the carbon-permeable membrane, of the methods and the results of testing it under the experimental circulating loop conditions. The results of carbon activity sensor calibration with the use of equilibrium samples of XI8H9, Fe -8Ni, Fe -12Mn materials are listed. The behaviour of carbon activity sensor signals in sodium under various transitional conditions and hydrodynamic perturbation in the circulating loop, containing carbon bearing impurities in the sodium flow and their deposits on the surfaces flushed by sodium, are described. (author)

Acid-base characteristics of powdered-activated-carbon surfaces

Energy Technology Data Exchange (ETDEWEB)

Reed, B.E. (West Virginia Univ., Morgantown (United States)); Jensen, J.N.; Matsumoto, M.R. (State Univ. of New York, Buffalo (United States))

Adsorption of heavy metals onto activated carbon has been described using the surface-complex-formation (SCF) model, a chemical equilibrium model. The SCF model requires a knowledge of the amphoteric nature of activated carbon prior to metal adsorption modeling. In the past, a single-diprotic-acid-site model had been employed to describe the amphoteric nature of activated-carbon surfaces. During this study, the amphoteric nature of two powdered activated carbons were investigated, and a three-monoprotic site surface model was found to be a plausible alternative. The single-diprotic-acid-site and two-monoprotic-site models did not describe the acid-base behavior of the two carbons studied adequately. The two-diprotic site was acceptable for only one of the study carbons. The acid-base behavior of activated carbon surfaces seem to be best modeled as a series of weak monoprotic acids.

Integration of implant planning workflows into the PACS infrastructure

Science.gov (United States)

Gessat, Michael; Strauß, Gero; Burgert, Oliver

2008-03-01

The integration of imaging devices, diagnostic workstations, and image servers into Picture Archiving and Communication Systems (PACS) has had an enormous effect on the efficiency of radiology workflows. The standardization of the information exchange between the devices with the DICOM standard has been an essential precondition for that development. For surgical procedures, no such infrastructure exists. With the increasingly important role computerized planning and assistance systems play in the surgical domain, an infrastructure that unifies the communication between devices becomes necessary. In recent publications, the need for a modularized system design has been established. A reference architecture for a Therapy Imaging and Model Management System (TIMMS) has been proposed. It was accepted by the DICOM Working Group 6 as the reference architecture for DICOM developments for surgery. In this paper we propose the inclusion of implant planning systems into the PACS infrastructure. We propose a generic information model for the patient specific selection and positioning of implants from a repository according to patient image data. The information models are based on clinical workflows from ENT, cardiac, and orthopedic surgery as well as technical requirements derived from different use cases and systems. We show an exemplary implementation of the model for application in ENT surgery: the selection and positioning of an ossicular implant in the middle ear. An implant repository is stored in the PACS. It makes use of an experimental implementation of the Surface Mesh Module that is currently being developed as extension to the DICOM standard.

EST-PAC a web package for EST annotation and protein sequence prediction

Directory of Open Access Journals (Sweden)

Strahm Yvan

2006-10-01

Full Text Available Abstract With the decreasing cost of DNA sequencing technology and the vast diversity of biological resources, researchers increasingly face the basic challenge of annotating a larger number of expressed sequences tags (EST from a variety of species. This typically consists of a series of repetitive tasks, which should be automated and easy to use. The results of these annotation tasks need to be stored and organized in a consistent way. All these operations should be self-installing, platform independent, easy to customize and amenable to using distributed bioinformatics resources available on the Internet. In order to address these issues, we present EST-PAC a web oriented multi-platform software package for expressed sequences tag (EST annotation. EST-PAC provides a solution for the administration of EST and protein sequence annotations accessible through a web interface. Three aspects of EST annotation are automated: 1 searching local or remote biological databases for sequence similarities using Blast services, 2 predicting protein coding sequence from EST data and, 3 annotating predicted protein sequences with functional domain predictions. In practice, EST-PAC integrates the BLASTALL suite, EST-Scan2 and HMMER in a relational database system accessible through a simple web interface. EST-PAC also takes advantage of the relational database to allow consistent storage, powerful queries of results and, management of the annotation process. The system allows users to customize annotation strategies and provides an open-source data-management environment for research and education in bioinformatics.

Behaviour of waterborne radon in activated carbon filters

International Nuclear Information System (INIS)

Haberer, K.; Akkermann-Kubillus, A.

1999-01-01

To investigate the behaviour of radon in adsorption/desorption processes in filter systems with different activated carbon types, measurements were focused on adsorption capacity, adsorption velocity, retain capability, interaction with ions (poisoning of active centers) and adsorption of radon daughters. Various activated carbon types derived from hard coal, brown coal, peat and wood, were used in adsorption tests runs with activated carbons which are frequently applied in water treatment facilities. In laboratory tests, water facility filter conditions were simulated using pilot plant columns filled with different carbon types. Finally, a small scale laboratory column was installed at a natural water source with elevated activity. Long-time filter runs were conducted under varying flow rates and with different amounts of the in waterworks wide-spread used activated carbon F-300. The main results observed were: 1. The amount of radioactivity adsorbed depends upon the type of carbon, its granular size and the contact time between the activated carbon and water. The decontamination capacity was between 19% and 94. 2. The DOC-levels of water influences the adsorbable radioactivity due to the poisoning of the active centres of the carbon. The adsorption velocity decreased down to 15%. 3. The maximum decontamination rate of the water under waterworks conditions was 60%. (orig.) [de

Incremental picture archiving and communication system (PACS) - an appraisal

International Nuclear Information System (INIS)

Nagle, K.

2000-01-01

Digital storage phosphor radiography is slowly being introduced in Australia with more sites making the conversion from film/screen to computed radiography or a fully integrated Picture Archiving and Communication System (PACS). St Vincent's Hospital, Melbourne (SVHM) introduced partial PACS for general radiography in June 1996. This involved networking two Fuji CR Image Plate Readers and an existing Kodak KESPR400 Reader with viewing stations strategically placed in Medical Imaging, Casualty and the Intensive and Coronary Care units. No long-term storage device or archive facility was purchased. This installation coincided with the relocation of the Medical Imaging Department (MID) to a fully equipped new site as well as the introduction of the Kestral Radiology Management System. The transition has involved significant changes to the department's design, workflow and the radiographers' work practices. Copyright (1999) Australian Institute of Radiography

ACTIVATED CARBON (CHARCOAL OBTAINING . APPLICATION

Directory of Open Access Journals (Sweden)

Florin CIOFU

2015-05-01

Full Text Available The activated carbon is a microporous sorbent with a very large adsorption area that can reach in some cases even 1500sqm / gram. Activated carbon is produced from any organic material with high carbon content: coal, wood, peat or moor coal, coconut shells. The granular activated charcoal is most commonly produced by grinding the raw material, adding a suitable binder to provide the desired hardness and shape. Enabling coal is a complete process through which the raw material is fully exposed to temperatures between 600-900 degrees C, in the absence of oxygen, usually in a domestic atmosphere as gases such as nitrogen or argon; as material that results from this process is exposed in an atmosphere of oxygen and steam at a temperature in the interval from 600 - 1200 degrees C.

A Recurrent De Novo PACS2 Heterozygous Missense Variant Causes Neonatal-Onset Developmental Epileptic Encephalopathy, Facial Dysmorphism, and Cerebellar Dysgenesis.

Science.gov (United States)

Olson, Heather E; Jean-Marçais, Nolwenn; Yang, Edward; Heron, Delphine; Tatton-Brown, Katrina; van der Zwaag, Paul A; Bijlsma, Emilia K; Krock, Bryan L; Backer, E; Kamsteeg, Erik-Jan; Sinnema, Margje; Reijnders, Margot R F; Bearden, David; Begtrup, Amber; Telegrafi, Aida; Lunsing, Roelineke J; Burglen, Lydie; Lesca, Gaetan; Cho, Megan T; Smith, Lacey A; Sheidley, Beth R; Moufawad El Achkar, Christelle; Pearl, Phillip L; Poduri, Annapurna; Skraban, Cara M; Tarpinian, Jennifer; Nesbitt, Addie I; Fransen van de Putte, Dietje E; Ruivenkamp, Claudia A L; Rump, Patrick; Chatron, Nicolas; Sabatier, Isabelle; De Bellescize, Julitta; Guibaud, Laurent; Sweetser, David A; Waxler, Jessica L; Wierenga, Klaas J; Donadieu, Jean; Narayanan, Vinodh; Ramsey, Keri M; Nava, Caroline; Rivière, Jean-Baptiste; Vitobello, Antonio; Tran Mau-Them, Frédéric; Philippe, Christophe; Bruel, Ange-Line; Duffourd, Yannis; Thomas, Laurel; Lelieveld, Stefan H; Schuurs-Hoeijmakers, Janneke; Brunner, Han G; Keren, Boris; Thevenon, Julien; Faivre, Laurence; Thomas, Gary; Thauvin-Robinet, Christel

2018-05-03

Developmental and epileptic encephalopathies (DEEs) represent a large clinical and genetic heterogeneous group of neurodevelopmental diseases. The identification of pathogenic genetic variants in DEEs remains crucial for deciphering this complex group and for accurately caring for affected individuals (clinical diagnosis, genetic counseling, impacting medical, precision therapy, clinical trials, etc.). Whole-exome sequencing and intensive data sharing identified a recurrent de novo PACS2 heterozygous missense variant in 14 unrelated individuals. Their phenotype was characterized by epilepsy, global developmental delay with or without autism, common cerebellar dysgenesis, and facial dysmorphism. Mixed focal and generalized epilepsy occurred in the neonatal period, controlled with difficulty in the first year, but many improved in early childhood. PACS2 is an important PACS1 paralog and encodes a multifunctional sorting protein involved in nuclear gene expression and pathway traffic regulation. Both proteins harbor cargo(furin)-binding regions (FBRs) that bind cargo proteins, sorting adaptors, and cellular kinase. Compared to the defined PACS1 recurrent variant series, individuals with PACS2 variant have more consistently neonatal/early-infantile-onset epilepsy that can be challenging to control. Cerebellar abnormalities may be similar but PACS2 individuals exhibit a pattern of clear dysgenesis ranging from mild to severe. Functional studies demonstrated that the PACS2 recurrent variant reduces the ability of the predicted autoregulatory domain to modulate the interaction between the PACS2 FBR and client proteins, which may disturb cellular function. These findings support the causality of this recurrent de novo PACS2 heterozygous missense in DEEs with facial dysmorphim and cerebellar dysgenesis. Copyright © 2018 American Society of Human Genetics. All rights reserved.

SPHERE: Irradiation of sphere-pac fuel of UPuO2−x containing 3% Americium

International Nuclear Information System (INIS)

D’Agata, E.; Hania, P.R.; McGinley, J.; Somers, J.; Sciolla, C.; Baas, P.J.; Kamer, S.; Okel, R.A.F.; Bobeldijk, I.; Delage, F.; Bejaoui, S.

2014-01-01

Highlights: • SPHERE is designed to check the behaviour of MADF sphere-pac concept. • MADF sphere-pac are compared with MADF pellet. • Swelling, helium release and restructuring behaviour will be the main output of the experiment. • An experiment to check sphere-pac MABB fuel behaviour is now under design. - Abstract: Americium is a strong contributor to the long term radiotoxicity of high activity nuclear waste. Transmutation by irradiation in nuclear reactors of long-lived nuclides like 241 Am is therefore an option for the reduction of radiotoxicity of waste packages to be stored in a repository. The SPHERE irradiation experiment is the latest of a series of European experiments on americium transmutation (e.g. EFTTRA-T4, EFTTRA-T4bis, HELIOS, MARIOS) performed in the HFR (High Flux Reactor). The SPHERE experiment is carried out in the framework of the 4-year project FAIRFUELS of the EURATOM 7th Framework Programme (FP7). During the past years of experimental works in the field of transmutation and tests of innovative nuclear fuels, the release or trapping of helium as well as helium induced fuel swelling have been shown to be the key issues for the design of Am-bearing targets. The main objective of the SPHERE experiment is to study the in-pile behaviour of fuel containing 3% of americium and to compare the behaviour of sphere-pac fuel to pellet fuel, in particular the role of microstructure and temperature on fission gas release (mainly He) and on fuel swelling. The SPHERE experiment is being irradiated since September 2013 in the HFR in Petten (The Netherlands) and is expected to be terminated in spring 2015. The experiment has been designed to last up to 18 reactor cycles (corresponding to 18 months) but may reach its target earlier. This paper discusses the rationale and objective of the SPHERE experiment and provides a general description of its design

Making the PACS workstation a browser of image processing software: a feasibility study using inter-process communication techniques.

Science.gov (United States)

Wang, Chunliang; Ritter, Felix; Smedby, Orjan

2010-07-01

To enhance the functional expandability of a picture archiving and communication systems (PACS) workstation and to facilitate the integration of third-part image-processing modules, we propose a browser-server style method. In the proposed solution, the PACS workstation shows the front-end user interface defined in an XML file while the image processing software is running in the background as a server. Inter-process communication (IPC) techniques allow an efficient exchange of image data, parameters, and user input between the PACS workstation and stand-alone image-processing software. Using a predefined communication protocol, the PACS workstation developer or image processing software developer does not need detailed information about the other system, but will still be able to achieve seamless integration between the two systems and the IPC procedure is totally transparent to the final user. A browser-server style solution was built between OsiriX (PACS workstation software) and MeVisLab (Image-Processing Software). Ten example image-processing modules were easily added to OsiriX by converting existing MeVisLab image processing networks. Image data transfer using shared memory added communication based on IPC techniques is an appealing method that allows PACS workstation developers and image processing software developers to cooperate while focusing on different interests.

Canadian ceramic breeder sphere-pac technology: Capability and recent results

International Nuclear Information System (INIS)

Sullivan, J.D.; Brayman, C.L.; Verrall, R.A.; Miller, J.M.; Gierszewski, P.J.; Londry, F.; Slavin, A.

1991-01-01

Sphere-pac ceramic breeders have been under development in Canada for several years. The goal is to fabricate and characterize these materials for use in engineering test reactors and subsequent fusion power reactors. Practical application of sphere-pac beds requires close consideration of both properties and fabrication. The present emphasis of the program is on 1-3 mm diameter Li 2 ZrO 3 spheres, with the future development of binary beds planned. Litre quantities have been produced by methods that are applicable to high production rates. These spheres are being tested for measurement of bulk properties (e.g., thermal conductivity, gas permeability, packing density, tritium release, specific heat) and long-term irradiation exposure. This paper summarizes the status of the work. (orig.)

Catalytic Growth of Macroscopic Carbon Nanofibers Bodies with Activated Carbon

Science.gov (United States)

Abdullah, N.; Rinaldi, A.; Muhammad, I. S.; Hamid, S. B. Abd.; Su, D. S.; Schlogl, R.

2009-06-01

Carbon-carbon composite of activated carbon and carbon nanofibers have been synthesized by growing Carbon nanofiber (CNF) on Palm shell-based Activated carbon (AC) with Ni catalyst. The composites are in an agglomerated shape due to the entanglement of the defective CNF between the AC particles forming a macroscopic body. The macroscopic size will allow the composite to be used as a stabile catalyst support and liquid adsorbent. The preparation of CNT/AC nanocarbon was initiated by pre-treating the activated carbon with nitric acid, followed by impregnation of 1 wt% loading of nickel (II) nitrate solutions in acetone. The catalyst precursor was calcined and reduced at 300° C for an hour in each step. The catalytic growth of nanocarbon in C2H4/H2 was carried out at temperature of 550° C for 2 hrs with different rotating angle in the fluidization system. SEM and N2 isotherms show the level of agglomeration which is a function of growth density and fluidization of the system. The effect of fluidization by rotating the reactor during growth with different speed give a significant impact on the agglomeration of the final CNF/AC composite and thus the amount of CNFs produced. The macrostructure body produced in this work of CNF/AC composite will have advantages in the adsorbent and catalyst support application, due to the mechanical and chemical properties of the material.

Behaviour of natural radionuclides on activated carbon filter

International Nuclear Information System (INIS)

Haberer, K.; Akkermann-Kubillus, A.; Dahlheimer, A.

1998-01-01

To investigate the behaviour of radon in adsorption/desorption processes at filter systems based on different activated carbon types, measurements were focused on adsorption capacity, adsorption velocity, retain capability, interaction with ions (poisoning of active centers) and adsorption of radon daughters. Various activated carbon types derived from hard coal, brown coal, peat and wood, were used in adsorption tests runs with activated carbons which are applied in water treatment facilities. In laboratory tests, water facility filter conditions were simulated using pilot plant columns filled with different carbon types. A small scale laboratory column was installed at a natural water source with elevated activity. Tests runs were conducted under varying flow rates and with different amounts of carbon. A full-scale waterworks filter system operated for 6 months was investigated for radon decay products adsorbed on the carbon. The main results observed were: 1. The amount of radioactivity adsorbed depends upon the type of carbon, its granular size and the contact time between the activated carbon and water. The decontamination capacity was between 19% and 94%. 2. The DOC-levels of water influences the adsorbable radioactivity due to the poisoning of the active centers of the carbon. The adsorption velocity decreased down to 15%. 3. The maximum decontamination rate of the water under waterworks conditions was 60%. (orig.) [de

Production of activated carbons from almond shell

Energy Technology Data Exchange (ETDEWEB)

Nabais, Joao M. Valente; Laginhas, Carlos Eduardo C.; Carrott, P.J.M.; Ribeiro Carrott, M.M.L. [Evora Univ. (Portugal). Centro de Quimica de Evora

2011-02-15

The production of activated carbons from almond shell, using physical activation by CO{sub 2} is reported in this work. The used method has produced activated carbons with apparent BET surface areas and micropore volume as high as 1138 m{sup 2} g{sup -1} and 0.49 cm{sup 3} g{sup -1}, respectively. The activated carbons produced have essentially primary micropores and only a small volume of wider micropores. By FTIR analysis it was possible to identify, in the surface of the activated carbons, several functional groups, namely hydroxyls (free and phenol), ethers, esters, lactones, pyrones and Si-H bonds. By the analysis of the XRD patterns it was possible to calculate the microcrystallites dimensions with height between 1.178 and 1.881 nm and width between 3.106 and 5.917 nm. From the XRD it was also possible to identify the presence of traces of inorganic heteroatoms such as Si, Pb, K, Fe and P. All activated carbons showed basic characteristics with point of zero charge between 9.42 and 10.43. (author)

Biogas pre-upgrading by adsorption of trace compounds onto granular activated carbons and an activated carbon fiber-cloth.

Science.gov (United States)

Boulinguiez, B; Le Cloirec, P

2009-01-01

The study assesses the adsorption onto activated carbon materials of selected volatile organic compounds -VOCs- (dichloromethane, 2-propanol, toluene, siloxane D4) in a biogas matrix composed of methane and carbon dioxide (55:45 v/v). Three different adsorbents are tested, two of them are granular activated carbon (GAC), and the last is an activated carbon fiber-cloth (ACFC). The adsorption isotherm data are fitted by different models by nonlinear regression. The Langmuir-Freundlich model appears to be the adequate one to describe the adsorption phenomena independently of the VOC considered or the adsorbent. The adsorbents present attractive adsorption capacity of the undesirable compounds in biogas atmosphere though the maximum adsorption capacities for a VOC are quite different from each other. The adsorption kinetics are characterized through three coefficients: the initial adsorption coefficient, the external film mass transfer coefficient and the internal diffusion coefficient of Weber. The ACFC demonstrates advanced kinetic yields compared to the granular activated carbon materials whatever VOC is considered. Therefore, pre-upgrading of biogas produced from wastewater sludge or co-digestion system by adsorption onto activated carbon appears worth investigating. Especially with ACFC material that presents correct adsorption capacities toward VOCs and concrete regeneration process opportunity to realize such process.

Preparation and characterisation of activated carbon

International Nuclear Information System (INIS)

Badri bin Muhammad; Karen binti Badri; Mohd Zobir bin Hussein; Zulkarnain bin Zainal; W.M. Daud bin W Yunus; Ramli bin Ibrahim

1994-01-01

Activated carbon was prepared from Agricultural wastes, such as coconut shell, Palm oil Shell and mangrove trunk by destructive distillation under vakuum. Chemical and Physical properties of the activated carbon were studied and some potentially useful application in the fields of chemistry was also carried out

Production of activated carbon from peanut hill using phosphoric acid and microwave activation

Directory of Open Access Journals (Sweden)

Weerawat Clowutimon

2015-06-01

Full Text Available The optimum conditions for preparing activated carbon from peanut hulls by phosphoric acid and microwave activation were studied. Factors investigated in this study were temperature of carbonization at 300, 350, 400 and 450๐ C, and time of carbonization at 30, 60 and 90 minutes. The optimum yield was observed that carbonization temperature of 400๐ C and time at 60 minutes, respectively. The yield of charcoal was 39% and the f ix carbon was 69%. Then the charcoal was activated by phosphoric acid and microwave irradiation, respectively. The effect of the weight per volume ratios of charcoal to activating acid (1:1, 1:2 and 2:1(W/V, microwave power at (activated 300, 500 and 700 watts, and activated time (30, 60 and 90 seconds were studied. The results showed that the optimum conditions for activating peanut charcoal were 1:2 (W/V charcoal per activating acid, microwave power 700 watts for 90 seconds. The results yielding maximum surface area by BET method was 303.1 m2 /g and pore volume was 0.140 cm3 /g. An efficiency of maximum iodine adsorption was 418 mg iodine/g activated carbon. Comparing the adsorption efficiency of non- irradiated and irradiated activated carbon, the efficiency of irradiated activated carbon improved up to 31%, due to its larger surface area and pore volume.

Adsorption and desorption of pertechnetate on activated carbon

International Nuclear Information System (INIS)

Dano, M.; Galambos, M.; Rajec, P.; Viglasova, E.; Krajnak, A.; Novak, I.

2014-01-01

High surface area, a microporous structure, and a high degree of surface reactivity make activated carbons versatile adsorbents, particularly effective in the adsorption of radionuclides from aqueous solutions. The most important property of activated carbon, the property that determines its usage, is the pore structure. The total number of pores, their shape and size determine the adsorption capacity and even the dynamic adsorption rate of the activated carbon. This report is dedicated to sorption properties of new activated carbon sorbents. (authors)

Innovate pin design for Sphere-pac fuel in sodium cooled fast reactors

International Nuclear Information System (INIS)

Pouchon, Manuel A.; Niceno, Bojan; Krepel, Jiri

2011-01-01

The paper discusses a new fuel element type, which combines a particle fuel concept, the Sphere-pac, with a new pin design which features internal cooling. Particle fuels are auspicious when considering a closed fuel cycle, where minor actinide containing fuels must be fabricated. The principle advantage lies in their production simplicity with much less maintenance intensive mechanical devices. Furthermore the Sphere-pac is usually produced by a wet and therefore powder-less route. Therefore the implementation in a remotely controlled and heavily shielded environment becomes easier to realize. Besides the advantages in the production process, the Sphere-pac bears one important disadvantage: the lower thermal conductivity of the particle arrangement, and the therefore higher peak temperatures in the fuel. Consequently a new fuel design is suggested in this paper. It offers an internal cooling channel and therefore smaller maximal fuel distances to the coolant. As the concept is new, the most important aspects are studied; these are the neutronics, the temperature profile in the fuel plus thermal-hydraulics aspects. (author)

Volumetric and superficial characterization of carbon activated

International Nuclear Information System (INIS)

Carrera G, L.M.; Garcia S, I.; Jimenez B, J.; Solache R, M.; Lopez M, B.; Bulbulian G, S.; Olguin G, M.T.

2000-01-01

The activated carbon is the resultant material of the calcination process of natural carbonated materials as coconut shells or olive little bones. It is an excellent adsorbent of diluted substances, so much in colloidal form, as in particles form. Those substances are attracted and retained by the carbon surface. In this work is make the volumetric and superficial characterization of activated carbon treated thermically (300 Centigrade) in function of the grain size average. (Author)

Protecting clinical data in PACS, teleradiology systems, and research environments

Science.gov (United States)

Meissner, Marion C.; Collmann, Jeff R.; Tohme, Walid G.; Mun, Seong K.

1997-05-01

As clinical data is more widely stored in electronic patient record management systems and transmitted over the Internet and telephone lines, it becomes more accessible and therefore more useful, but also more vulnerable. Computer systems such as PACS, telemedicine applications, and medical research networks must protect against accidental or deliberate modification, disclosure, and violation of patient confidentiality in order to be viable. Conventional wisdom in the medical field and among lawmakers legislating the use of electronic medical records suggests that, although it may improve access to information, an electronic medical record cannot be as secure as a traditional paper record. This is not the case. Information security is a well-developed field in the computer and communications industry. If medical information systems, such as PACS, telemedicine applications, and research networks, properly apply information security techniques, they can ensure the accuracy and confidentiality of their patient information and even improve the security of their data over a traditional paper record. This paper will elaborate on some of these techniques and discuss how they can be applied to medical information systems. The following systems will be used as examples for the analysis: a research laboratory at Georgetown University Medical Center, the Deployable Radiology system installed to support the US Army's peace- keeping operation in Bosnia, a kidney dialysis telemedicine system in Washington, D.C., and various experiences with implementing and integrating PACS.

SAXS study on activated carbons

International Nuclear Information System (INIS)

Bota, A.; Heringer, D.; Mihalffy, T.

1999-01-01

SAXS fractal analysis of activated carbons is presented. It gives very useful information about the structural changes of the carbon skeleton. From the fact, that the sequence of the activation and the heat treatment affect the fractal behaviours more drastically than the particle size distribution of the structural units, it follows that all changes in the pore and matrix structure may reduce principally to the bonding of the crystallite units. (K.A.)

Poetry and cultural identity in F. T. Pacéré's writing: from identity ...

African Journals Online (AJOL)

My concern is the socio-cultural characteristics of F. T. Pacéré's poetry and their aesthetic and semantic structuring role. Pacéré's poetry is not just about identity affirmation; it is also about being open to the world, namely other people and other cultures. Through this, it seeks to achieve universal humanism. I conclude my ...

PERFORMANCE AND COST OF MERCURY AND MULTIPOLLUTANT EMISSION CONTROL TECHNOLOGY APPLICATIONS ON ELECTRIC UTILITY BOILERS

Science.gov (United States)

The report presents estimates of the performance and cost of both powdered activated carbon (PAC) and multipollutant control technologies that may be useful in controlling mercury emissions. Based on currently available data, cost estimates for PAC injection range are 0.03-3.096 ...

Chronic exposure of the oligochaete Lumbriculus variegatus to Polycyclic Aromatic Compounds (PACs): Bioavailability and effects on reproduction

NARCIS (Netherlands)

León Paumen, M.; Stol, P.; ter Laak, T.L.; Kraak, M.H.S.; van Gestel, C.A.M.; Admiraal, W.

2008-01-01

This study aimed to monitor PAC availability to the oligochaete Lumbriculus variegatus during 28 days of exposure to spiked sediments, in order to obtain reliable chronic effect concentrations for reproduction. Sediment toxicity tests were performed using three pairs of PAC isomers: two homocyclic

Chronic exposure of the oligochaete Lumbriculus variegatus to polycyclic aromatic compounds (PACs): bioavailability and effects on reproduction.

NARCIS (Netherlands)

Leon Paumen, M.; Stol, P.; ter Laak, T.L.; Kraak, M.H.S.; van Gestel, C.A.M.; Admiraal, W.

2008-01-01

This study aimed to monitor PAC availability to the oligochaete Lumbriculus variegatus during 28 days of exposure to spiked sediments, in order to obtain reliable chronic effect concentrations for reproduction. Sediment toxicity tests were performed using three pairs of PAC isomers: two homocyclic

Reuse performance of granular-activated carbon and activated carbon fiber in catalyzed peroxymonosulfate oxidation.

Science.gov (United States)

Yang, Shiying; Li, Lei; Xiao, Tuo; Zhang, Jun; Shao, Xueting

2017-03-01

Recently, activated carbon was investigated as an efficient heterogeneous metal-free catalyst to directly activate peroxymonosulfate (PMS) for degradation of organic compounds. In this paper, the reuse performance and the possible deactivation reasons of granular-activated carbon (GAC) and activated carbon fiber (ACF) in PMS activation were investigated. As results indicated, the reusability of GAC, especially in the presence of high PMS dosage, was relatively superior to ACF in catalyzed PMS oxidation of Acid Orange 7 (AO7), which is much more easily adsorbed by ACF than by GAC. Pre-oxidation experiments were studied and it was demonstrated that PMS oxidation on ACF would retard ACF's deactivation to a big extent. After pre-adsorption with AO7, the catalytic ability of both GAC and ACF evidently diminished. However, when methanol was employed to extract the AO7-spent ACF, the catalytic ability could recover quite a bit. GAC and ACF could also effectively catalyze PMS to degrade Reactive Black 5 (RB5), which is very difficult to be adsorbed even by ACF, but both GAC and ACF have poor reuse performance for RB5 degradation. The original organic compounds or intermediate products adsorbed by GAC or ACF would be possibly responsible for the deactivation.

Confirmatory factor analysis of the Patient Assessment of Constipation-Symptoms (PAC-SYM) among patients with chronic constipation

DEFF Research Database (Denmark)

Neri, Luca; Conway, Paul Maurice; Basilisco, Guido

2015-01-01

the psychometric properties of PAC-SYM in patients with chronic constipation. METHODS: We enrolled 2,203 outpatients with chronic constipation in two waves. We used wave I sample to test the psychometric properties of the PAC-SYM and wave II sample to cross-validate its factor structure, to assess criterion...... validity, responsiveness to clinical change, and its minimal clinically important difference. RESULTS: Only a minority of patients reported any rectal tearing (38 %). Deletion of such item leads to a 11-item version (M:PAC-SYM). The remaining items in the rectal domain were moderately correlated.......28-0.45), discrimination across Rome III criteria for functional constipation and abdominal pain, and responsiveness to clinical change (β = -0.49; ω (2) = 0.25). M:PAC-SYM minimal clinically important difference was 0.24. CONCLUSION: Our analysis shows that the rectal domain may not represent a relevant cluster...

The Adsorption Mechanism of Modified Activated Carbon on Phenol

Directory of Open Access Journals (Sweden)

Lin J. Q.

2016-01-01

Full Text Available Modified activated carbon was prepared by thermal treatment at high temperature under nitrogen flow. The surface properties of the activated carbon were characterized by Boehm titration, BET and point of zero charge determination. The adsorption mechanism of phenol on modified activated carbon was explained and the adsorption capacity of modified activated carbon for phenol when compared to plain activated carbon was evaluated through the analysis of adsorption isotherms, thermodynamic and kinetic properties. Results shows that after modification the surface alkaline property and pHpzc value of the activated carbon increase and the surface oxygen-containing functional groups decrease. The adsorption processes of the plain and modified carbon fit with Langmuir isotherm equation well, and the maximum adsorption capacity increase from 123.46, 111.11, 103.09mg/g to 192.31, 178.57, 163,93mg/g under 15, 25 and 35°C after modification, respectively. Thermodynamic parameters show that the adsorption of phenol on activated carbon is a spontaneously exothermic process of entropy reduction, implying that the adsorption is a physical adsorption. The adsorption of phenol on activated carbon follows the pseudo-second-order kinetics (R2>0.99. The optimum pH of adsorption is 6~8.

PacIOOS Nearshore Sensor 13 (NS13): Kahului, Maui, Hawaii

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The nearshore sensors are part of the Pacific Islands Ocean Observing System (PacIOOS) and are designed to measure a variety of ocean parameters at fixed point...

PacIOOS Nearshore Sensor 16 (NS16): Wailupe, Oahu, Hawaii

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The nearshore sensors are part of the Pacific Islands Ocean Observing System (PacIOOS) and are designed to measure a variety of ocean parameters at fixed point...

PacIOOS Nearshore Sensor 09 (NS09): Cetti Bay, Guam

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The nearshore sensors are part of the Pacific Islands Ocean Observing System (PacIOOS) and are designed to measure a variety of ocean parameters at fixed point...

PacIOOS Nearshore Sensor 15 (NS15): Pago Bay, Guam

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The nearshore sensors are part of the Pacific Islands Ocean Observing System (PacIOOS) and are designed to measure a variety of ocean parameters at fixed point...

PacIOOS Nearshore Sensor 07 (NS07): Majuro, Marshall Islands

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The nearshore sensors are part of the Pacific Islands Ocean Observing System (PacIOOS) and are designed to measure a variety of ocean parameters at fixed point...

Effect of carbon black on thermal properties of charcoal and salacca leafstalk briquettes

Science.gov (United States)

Thassana, Chewa; Nuleg, Witoon

2017-08-01

In this work, the effect of a carbon black (CB) on the thermal properties of briquettes produced from the charcoal and the salacca leafstalk with and without CB have been investigated. Four thermal properties of a briquettes compose of the burning time, the calorific value, the percentage moisture (PMC) and an percentage ash content (PAC) were analyzed using standard laboratory methods. Our results were indicated that the sallacca leafstalk mix a carbon black is the long burning times, high heating but a few ash content. Results shown that the burning time and the calorific value of a charcoal, a charcoal with CB, the salacca leafstalk and the salacca leafstalk with carbon black particles is about 58, 63, 76, 81 minutes, and 10.33, 12.96, 13.12, 14.63 MJ/kg, respectively. In addition, the PMC and PAC were in range of 11.6 - 8.14% and 9.33 - 5.42%. So, we can conclude that a cabon black affect on the thermal properties of a briquettes and salacca leaftstalk mixed CB has been most suited for briquetting.

Quality of poultry litter-derived granular activated carbon.

Science.gov (United States)

Qiu, Guannan; Guo, Mingxin

2010-01-01

Utilization of poultry litter as a source material for generating activated carbon is a value-added and environmentally beneficial approach to recycling organic waste. In this study, the overall quality of poultry litter-derived granular activated carbon was systematically evaluated based on its various physical and chemical properties. Granular activated carbon generated from pelletized poultry litter following a typical steam-activation procedure possessed numerous micropores in the matrix. The product exhibited a mean particle diameter of 2.59 mm, an apparent density of 0.45 g cm(-3), a ball-pan hardness of 91.0, an iodine number of 454 mg g(-1), and a BET surface area of 403 m(2) g(-1). It contained high ash, nitrogen, phosphorus contents and the trace elements Cu, Zn, and As. Most of the nutrients and toxic elements were solidified and solution-unextractable. In general, poultry litter-based activated carbon demonstrated overall quality comparable to that of low-grade commercial activated carbon derived from coconut shell and bituminous coal. It is promising to use poultry litter as a feedstock to manufacture activated carbon for wastewater treatment.