WorldWideScience

Sample records for acm 4b3 antiglucuronoxilomanano

  1. ACME-III and ACME-IV Final Campaign Reports

    Biraud, S. C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2016-01-01

    The goals of the Atmospheric Radiation Measurement (ARM) Climate Research Facility’s third and fourth Airborne Carbon Measurements (ACME) field campaigns, ACME-III and ACME-IV, are: 1) to measure and model the exchange of CO2, water vapor, and other greenhouse gases by the natural, agricultural, and industrial ecosystems of the Southern Great Plains (SGP) region; 2) to develop quantitative approaches to relate these local fluxes to the concentration of greenhouse gases measured at the Central Facility tower and in the atmospheric column above the ARM SGP Central Facility, 3) to develop and test bottom-up measurement and modeling approaches to estimate regional scale carbon balances, and 4) to develop and test inverse modeling approaches to estimate regional scale carbon balance and anthropogenic sources over continental regions. Regular soundings of the atmosphere from near the surface into the mid-troposphere are essential for this research.

  2. ACM Bundles on Del Pezzo surfaces

    Joan Pons-Llopis

    2009-11-01

    Full Text Available ACM rank 1 bundles on del Pezzo surfaces are classified in terms of the rational normal curves that they contain. A complete list of ACM line bundles is provided. Moreover, for any del Pezzo surface X of degree less or equal than six and for any n ≥ 2 we construct a family of dimension ≥ n − 1 of non-isomorphic simple ACM bundles of rank n on X.

  3. Asbestos-Containing Materials (ACM) and Demolition

    There are specific federal regulatory requirements that require the identification of asbestos-containing materials (ACM) in many of the residential buildings that are being demolished or renovated by a municipality.

  4. ACME: A Basis for Architecture Exchange

    Wile, David

    2003-01-01

    .... It remains useful in that role, but since the project's inception the Acme language and its support toolkit have grown into a solid foundation upon which new software architecture design and analysis...

  5. Quark ACM with topologically generated gluon mass

    Choudhury, Ishita Dutta; Lahiri, Amitabha

    2016-03-01

    We investigate the effect of a small, gauge-invariant mass of the gluon on the anomalous chromomagnetic moment (ACM) of quarks by perturbative calculations at one-loop level. The mass of the gluon is taken to have been generated via a topological mass generation mechanism, in which the gluon acquires a mass through its interaction with an antisymmetric tensor field Bμν. For a small gluon mass ( ACM at momentum transfer q2 = -M Z2. We compare those with the ACM calculated for the gluon mass arising from a Proca mass term. We find that the ACM of up, down, strange and charm quarks vary significantly with the gluon mass, while the ACM of top and bottom quarks show negligible gluon mass dependence. The mechanism of gluon mass generation is most important for the strange quarks ACM, but not so much for the other quarks. We also show the results at q2 = -m t2. We find that the dependence on gluon mass at q2 = -m t2 is much less than at q2 = -M Z2 for all quarks.

  6. Additive Construction with Mobile Emplacement (ACME)

    Vickers, John

    2015-01-01

    The Additive Construction with Mobile Emplacement (ACME) project is developing technology to build structures on planetary surfaces using in-situ resources. The project focuses on the construction of both 2D (landing pads, roads, and structure foundations) and 3D (habitats, garages, radiation shelters, and other structures) infrastructure needs for planetary surface missions. The ACME project seeks to raise the Technology Readiness Level (TRL) of two components needed for planetary surface habitation and exploration: 3D additive construction (e.g., contour crafting), and excavation and handling technologies (to effectively and continuously produce in-situ feedstock). Additionally, the ACME project supports the research and development of new materials for planetary surface construction, with the goal of reducing the amount of material to be launched from Earth.

  7. Porcine bladder acellular matrix (ACM): protein expression, mechanical properties

    Farhat, Walid A [Department of Surgery, Division of Urology, University of Toronto and Hospital for Sick Children, Toronto, ON M5G 1X8 (Canada); Chen Jun; Haig, Jennifer; Antoon, Roula; Litman, Jessica; Yeger, Herman [Department of Developmental and Stem Cell Biology, Research Institute, Hospital for Sick Children, Toronto, ON M5G 1X8 (Canada); Sherman, Christopher [Department of Anatomic Pathology, Sunnybrook and Women' s College Health Sciences Centre, Toronto, ON (Canada); Derwin, Kathleen [Department of Biomedical Engineering, Lerner Research Institute and Orthopaedic Research Center, Cleveland Clinic Foundation, Cleveland, OH (United States)], E-mail: walid.farhat@sickkids.ca

    2008-06-01

    Experimentally, porcine bladder acellular matrix (ACM) that mimics extracellular matrix has excellent potential as a bladder substitute. Herein we investigated the spatial localization and expression of different key cellular and extracellular proteins in the ACM; furthermore, we evaluated the inherent mechanical properties of the resultant ACM prior to implantation. Using a proprietary decellularization method, the DNA contents in both ACM and normal bladder were measured; in addition we used immunohistochemistry and western blots to quantify and localize the different cellular and extracellular components, and finally the mechanical testing was performed using a uniaxial mechanical testing machine. The mean DNA content in the ACM was significantly lower in the ACM compared to the bladder. Furthermore, the immunohistochemical and western blot analyses showed that collagen I and IV were preserved in the ACM, but possibly denatured collagen III in the ACM. Furthermore, elastin, laminin and fibronectin were mildly reduced in the ACM. Although the ACM did not exhibit nucleated cells, residual cellular components (actin, myosin, vimentin and others) were still present. There was, on the other hand, no significant difference in the mean stiffness between the ACM and the bladder. Although our decellularization method is effective in removing nuclear material from the bladder while maintaining its inherent mechanical properties, further work is mandatory to determine whether these residual DNA and cellular remnants would lead to any immune reaction, or if the mechanical properties of the ACM are preserved upon implantation and cellularization.

  8. Porcine bladder acellular matrix (ACM): protein expression, mechanical properties

    Farhat, Walid A; Chen Jun; Haig, Jennifer; Antoon, Roula; Litman, Jessica; Yeger, Herman; Sherman, Christopher; Derwin, Kathleen

    2008-01-01

    Experimentally, porcine bladder acellular matrix (ACM) that mimics extracellular matrix has excellent potential as a bladder substitute. Herein we investigated the spatial localization and expression of different key cellular and extracellular proteins in the ACM; furthermore, we evaluated the inherent mechanical properties of the resultant ACM prior to implantation. Using a proprietary decellularization method, the DNA contents in both ACM and normal bladder were measured; in addition we used immunohistochemistry and western blots to quantify and localize the different cellular and extracellular components, and finally the mechanical testing was performed using a uniaxial mechanical testing machine. The mean DNA content in the ACM was significantly lower in the ACM compared to the bladder. Furthermore, the immunohistochemical and western blot analyses showed that collagen I and IV were preserved in the ACM, but possibly denatured collagen III in the ACM. Furthermore, elastin, laminin and fibronectin were mildly reduced in the ACM. Although the ACM did not exhibit nucleated cells, residual cellular components (actin, myosin, vimentin and others) were still present. There was, on the other hand, no significant difference in the mean stiffness between the ACM and the bladder. Although our decellularization method is effective in removing nuclear material from the bladder while maintaining its inherent mechanical properties, further work is mandatory to determine whether these residual DNA and cellular remnants would lead to any immune reaction, or if the mechanical properties of the ACM are preserved upon implantation and cellularization

  9. Porcine bladder acellular matrix (ACM): protein expression, mechanical properties.

    Farhat, Walid A; Chen, Jun; Haig, Jennifer; Antoon, Roula; Litman, Jessica; Sherman, Christopher; Derwin, Kathleen; Yeger, Herman

    2008-06-01

    Experimentally, porcine bladder acellular matrix (ACM) that mimics extracellular matrix has excellent potential as a bladder substitute. Herein we investigated the spatial localization and expression of different key cellular and extracellular proteins in the ACM; furthermore, we evaluated the inherent mechanical properties of the resultant ACM prior to implantation. Using a proprietary decellularization method, the DNA contents in both ACM and normal bladder were measured; in addition we used immunohistochemistry and western blots to quantify and localize the different cellular and extracellular components, and finally the mechanical testing was performed using a uniaxial mechanical testing machine. The mean DNA content in the ACM was significantly lower in the ACM compared to the bladder. Furthermore, the immunohistochemical and western blot analyses showed that collagen I and IV were preserved in the ACM, but possibly denatured collagen III in the ACM. Furthermore, elastin, laminin and fibronectin were mildly reduced in the ACM. Although the ACM did not exhibit nucleated cells, residual cellular components (actin, myosin, vimentin and others) were still present. There was, on the other hand, no significant difference in the mean stiffness between the ACM and the bladder. Although our decellularization method is effective in removing nuclear material from the bladder while maintaining its inherent mechanical properties, further work is mandatory to determine whether these residual DNA and cellular remnants would lead to any immune reaction, or if the mechanical properties of the ACM are preserved upon implantation and cellularization.

  10. CLIC-ACM: Acquisition and Control System

    Bielawski, B; Magnoni, S

    2014-01-01

    CLIC [1] (Compact Linear Collider) is a world-wide collaboration to study the next terascale lepton collider, relying upon a very innovative concept of two-beamacceleration. In this scheme, the power is transported to the main accelerating structures by a primary electron beam. The Two Beam Module (TBM) is a compact integration with a high filling factor of all components: RF, Magnets, Instrumentation, Vacuum, Alignment and Stabilization. This paper describes the very challenging aspects of designing the compact system to serve as a dedicated Acquisition & Control Module (ACM) for all signals of the TBM. Very delicate conditions must be considered, in particular radiation doses that could reach several kGy in the tunnel. In such severe conditions shielding and hardened electronics will have to be taken into consideration. In addition, with more than 300 ADC&DAC channels per ACM and about 21000 ACMs in total, it appears clearly that power consumption will be an important issue. It is also obvious that...

  11. Porosity of porcine bladder acellular matrix: impact of ACM thickness.

    Farhat, Walid; Chen, Jun; Erdeljan, Petar; Shemtov, Oren; Courtman, David; Khoury, Antoine; Yeger, Herman

    2003-12-01

    The objectives of this study are to examine the porosity of bladder acellular matrix (ACM) using deionized (DI) water as the model fluid and dextran as the indicator macromolecule, and to correlate the porosity to the ACM thickness. Porcine urinary bladders from pigs weighing 20-50 kg were sequentially extracted in detergent containing solutions, and to modify the ACM thickness, stretched bladders were acellularized in the same manner. Luminal and abluminal ACM specimens were subjected to fixed static DI water pressure (10 cm); and water passing through the specimens was collected at specific time interval. While for the macromolecule porosity testing, the diffusion rate and direction of 10,000 MW fluoroescein-labeled dextrans across the ACM specimens mounted in Ussing's chambers were measured. Both experiments were repeated on the thin stretched ACM. In both ACM types, the fluid porosity in both directions did not decrease with increased test duration (3 h); in addition, the abluminal surface was more porous to fluid than the luminal surface. On the other hand, when comparing thin to thick ACM, the porosity in either direction was higher in the thick ACM. Macromolecule porosity, as measured by absorbance, was higher for the abluminal thick ACM than the luminal side, but this characteristic was reversed in the thin ACM. Comparing thin to thick ACM, the luminal side in the thin ACM was more porous to dextran than in the thick ACM, but this characteristic was reversed for the abluminal side. The porcine bladder ACM possesses directional porosity and acellularizing stretched urinary bladders may increase structural density and alter fluid and macromolecule porosity. Copyright 2003 Wiley Periodicals, Inc. J Biomed Mater Res 67A: 970-974, 2003

  12. ACM CCS 2013-2015 Student Travel Support

    2016-10-29

    ACM CCS 2013-2015 Student Travel Support Under the ARO funded effort titled “ACM CCS 2013-2015 Student Travel Support,” from 2013 to 2015, George...Computer and Communications Security (ACM CCS ). The views, opinions and/or findings contained in this report are those of the author(s) and should not...AGENCY NAME(S) AND ADDRESS (ES) U.S. Army Research Office P.O. Box 12211 Research Triangle Park, NC 27709-2211 travel grant, acm ccs REPORT

  13. AcmD, a homolog of the major autolysin AcmA of Lactococcus lactis, binds to the cell wall and contributes to cell separation and autolysis

    Visweswaran, Ganesh Ram R; Steen, Anton; Leenhouts, Kees; Szeliga, Monika; Ruban, Beata; Hesseling-Meinders, Anne; Dijkstra, Bauke W; Kuipers, Oscar P; Kok, Jan; Buist, Girbe

    2013-01-01

    Lactococcus lactis expresses the homologous glucosaminidases AcmB, AcmC, AcmA and AcmD. The latter two have three C-terminal LysM repeats for peptidoglycan binding. AcmD has much shorter intervening sequences separating the LysM repeats and a lower iso-electric point (4.3) than AcmA (10.3). Under

  14. Luminescent properties of red-emitting LiSr4B3O(9−3x/2)Nx:Eu2+ phosphor for white-LEDs

    Yu Hua; Deng Degang; Xu Shiqing; Yu Cuiping; Yin Haoyong; Nie Qiulin

    2012-01-01

    An Eu 2+ -activated oxynitride LiSr (4−y) B 3 O (9−3x/2) N x :yEu 2+ red-emitting phosphor was synthesized by solid-state reactions. The synthesized phosphor crystallized in a cubic system with space group Ia–3d. The LiSr 4 B 3 O (9−3x/2) N x :Eu 2+ phosphors exhibited a broad red emission band with a peak at 610 nm and a full width at half maximum of 106 nm under 410 nm excitation, which is ascribed to the 4f 6 5d 1 →4f 7 transition of Eu 2+ . The optimal doped nitrogen concentration was observed to be x=0.75. The average decay times of two different emission centers were estimated to be 568 and 489 ns in the LiSr 3.99 B 3 O 8.25 N 0.5 :0.01Eu 2+ phosphors, respectively. Concentration quenching of Eu 2+ ions occurred at y=0.07, and the critical distance was determined as 17.86 Å. The non-radiative transitions via dipole–dipole interactions resulted in the concentration quenching of Eu 2+ -site emission centers in the LiSr 4 B 3 O 9 host. These results indicate LiSr 4 B 3 O (9−3x/2) N x :Eu 2+ phosphor is promising for application in white near-UV LEDs. - Highlights: ► An oxynitride LiSr 4 B 3 O 9 N:Eu 2+ red-emitting phosphor was prepared at low synthesis temperature. ► The introduced nitrogen improved the excitation and emission intensity of the phosphor. ► The wide excitation band matches well with near-UV LED chips. ► The emission spectrum of the phosphor showed a broad full width at half maximum of about 106 nm.

  15. De afschaffing van de bezwaarfase bij boetebesluiten van de ACM

    Jans, J.H.; Outhuijse, A.

    Per 1 maart 2013 ontstaat door samenvoeging van de NMa, de OPTA en de Consumentenautoriteit, de Autoriteit Consument en Markt. Om de ACM slagvaardig te laten functioneren, wordt voorgesteld het handhavingsinstrumentarium m.b.t. het markttoezicht van de ACM te vereenvoudigen. Eén van de voorstellen

  16. Analysis on working pressure selection of ACME integral test facility

    Chen Lian; Chang Huajian; Li Yuquan; Ye Zishen; Qin Benke

    2011-01-01

    An integral effects test facility, advanced core cooling mechanism experiment facility (ACME) was designed to verify the performance of the passive safety system and validate its safety analysis codes of a pressurized water reactor power plant. Three test facilities for AP1000 design were introduced and review was given. The problems resulted from the different working pressures of its test facilities were analyzed. Then a detailed description was presented on the working pressure selection of ACME facility as well as its characteristics. And the approach of establishing desired testing initial condition was discussed. The selected 9.3 MPa working pressure covered almost all important passive safety system enables the ACME to simulate the LOCAs with the same pressure and property similitude as the prototype. It's expected that the ACME design would be an advanced core cooling integral test facility design. (authors)

  17. The molecular structure of the borate mineral inderite Mg(H4B3O7)(OH) · 5H2O--a vibrational spectroscopic study.

    Frost, Ray L; López, Andrés; Xi, Yunfei; Lima, Rosa Malena Fernandes; Scholz, Ricardo; Granja, Amanda

    2013-12-01

    We have undertaken a study of the mineral inderite Mg(H4B3O7)(OH) · 5H2O a hydrated hydroxy borate mineral of magnesium using scanning electron microscopy, thermogravimetry and vibrational spectroscopic techniques. The structure consists of [Formula: see text] soroborate groups and Mg(OH)2(H2O)4 octahedra interconnected into discrete molecules by the sharing of two OH groups. Thermogravimetry shows a mass loss of 47.2% at 137.5 °C, proving the mineral is thermally unstable. Raman bands at 954, 1047 and 1116 cm(-1) are assigned to the trigonal symmetric stretching mode. The two bands at 880 and 916 cm(-1) are attributed to the symmetric stretching mode of the tetrahedral boron. Both the Raman and infrared spectra of inderite show complexity. Raman bands are observed at 3052, 3233, 3330, 3392 attributed to water stretching vibrations and 3459 cm(-1) with sharper bands at 3459, 3530 and 3562 cm(-1) assigned to OH stretching vibrations. Vibrational spectroscopy is used to assess the molecular structure of inderite. Copyright © 2013 Elsevier B.V. All rights reserved.

  18. Proceedings of the ACM SIGIR Workshop ''Searching Spontaneous Conversational Speech''

    de Jong, Franciska M.G.; Oard, Douglas; Ordelman, Roeland J.F.; Raaijmakers, Stephan

    2007-01-01

    The Proceedings contain the contributions to the workshop on Searching Spontaneous Conversational Speech organized in conjunction with the 30th ACM SIGIR, Amsterdam 2007. The papers reflect some of the emerging focus areas and cross-cutting research topics, together addressing evaluation metrics,

  19. Preliminary proceedings of the 2001 ACM SIGPLAN Haskell workshop

    Hinze, R.

    2001-01-01

    This volume contains the preliminary proceedings of the 2001 ACM SIGPLAN Haskell Workshop, which was held on 2nd September 2001 in Firenze, Italy. The final proceedings will published by Elsevier Science as an issue of Electronic Notes in Theoretical Computer Science (Volume 59). The

  20. News from the Library: A one-stop-shop for computing literature: ACM Digital Library

    CERN Library

    2011-01-01

    The Association for Computing Machinery, ACM, is the world’s largest educational and scientific computing society. Among others, the ACM provides the computing field's premier Digital Library and serves its members and the computing profession with leading-edge publications, conferences, and career resources.   ACM Digital Library is available to the CERN community. The most popular journal here at CERN is Communications of the ACM. However, the collection offers access to a series of other valuable important academic journals such as Journal of the ACM and even fulltext of a series of classical books. In addition, users have access to the ACM Guide to Computing Literature, the most comprehensive bibliographic database focusing on computing, integrated with ACM’s full-text articles and including features such as ACM Author Profile Pages - which provides bibliographic and bibliometric data for over 1,000,000 authors in the field. ACM Digital Library is an excellent com...

  1. Proceedings of the 2014 ACM international conference on Interactive experiences for TV and online video

    P. Olivier (Patrick); P. Wright; T. Bartindale; M. Obrist (Marianna); P.S. Cesar Garcia (Pablo Santiago); S. Basapur

    2014-01-01

    htmlabstractIt is our great pleasure to introduce the 2014 ACM International Conference on Interactive Experiences for Television and Online Video -- ACM TVX 2014. ACM TVX is a leading annual conference that brings together international researchers and practitioners from a wide range of

  2. Proceedings of the 2nd ACM SIGSPATIAL International Workshop on Indoor Spatial Awareness

    These proceedings contain the papers selected for presentation at the Second International Workshop on Indoor Spatial Awareness, hosted by ACM SIGSPATIAL and held in conjunction with the18th ACM SIGSPATIAL International Conference on Advances in Geographic Information Systems (ACM SIGSPATIAL GIS...

  3. 76 FR 64943 - Proposed Cercla Administrative Cost Recovery Settlement; ACM Smelter and Refinery Site, Located...

    2011-10-19

    ... Settlement; ACM Smelter and Refinery Site, Located in Cascade County, MT AGENCY: Environmental Protection... projected future response costs concerning the ACM Smelter and Refinery NPL Site (Site), Operable Unit 1..., Helena, MT 59626. Mr. Sturn can be reached at (406) 457-5027. Comments should reference the ACM Smelter...

  4. Distribution of the ACME-arcA gene among meticillin-resistant Staphylococcus haemolyticus and identification of a novel ccr allotype in ACME-arcA-positive isolates.

    Pi, Borui; Yu, Meihong; Chen, Yagang; Yu, Yunsong; Li, Lanjuan

    2009-06-01

    The aim of this study was to investigate the prevalence and characteristics of ACME (arginine catabolic mobile element)-arcA-positive isolates among meticillin-resistant Staphylococcus haemolyticus (MRSH). ACME-arcA, native arcA and SCCmec elements were detected by PCR. Susceptibilities to 10 antimicrobial agents were compared between ACME-arcA-positive and -negative isolates by chi-square test. PFGE was used to investigate the clonal relatedness of ACME-arcA-positive isolates. The phylogenetic relationships of ACME-arcA and native arcA were analysed using the neighbour-joining methods of mega software. A total of 42 (47.7 %) of 88 isolates distributed in 13 PFGE types were positive for the ACME-arcA gene. There were no significant differences in antimicrobial susceptibility between ACME-arcA-positive and -negative isolates. A novel ccr allotype (ccrAB(SHP)) was identified in ACME-arcA-positive isolates. Among 42 ACME-arcA-positive isolates: 8 isolates harboured SCCmec V, 8 isolates harboured class C1 mec complex and ccrAB(SHP); 22 isolates harbouring class C1 mec complex and 4 isolates harbouring class C2 mec complex were negative for all known ccr allotypes. The ACME-arcA-positive isolates were first found in MRSH with high prevalence and clonal diversity, which suggests a mobility of ACME within MRSH. The results from this study revealed that MRSH is likely to be one of the potential reservoirs of ACME for Staphylococcus aureus.

  5. Highlights from ACM SIGSPATIAL GIS 2011: the 19th ACM SIGSPATIAL International Conference on Advances in Geographic Information Systems: (Chicago, Illinois - November 1 - 4, 2011)

    Jensen, Christian S.; Ofek, Eyal; Tanin, Egemen

    2012-01-01

    ACM SIGSPATIAL GIS 2011 was the 19th gathering of the premier event on spatial information and Geographic Information Systems (GIS). It is also the fourth year that the conference was held under the auspices of ACM's most recent special interest group, SIGSPATIAL. Since its start in 1993, the con...

  6. Design of ACM system based on non-greedy punctured LDPC codes

    Lu, Zijun; Jiang, Zihong; Zhou, Lin; He, Yucheng

    2017-08-01

    In this paper, an adaptive coded modulation (ACM) scheme based on rate-compatible LDPC (RC-LDPC) codes was designed. The RC-LDPC codes were constructed by a non-greedy puncturing method which showed good performance in high code rate region. Moreover, the incremental redundancy scheme of LDPC-based ACM system over AWGN channel was proposed. By this scheme, code rates vary from 2/3 to 5/6 and the complication of the ACM system is lowered. Simulations show that more and more obvious coding gain can be obtained by the proposed ACM system with higher throughput.

  7. Air Traffic Complexity Measurement Environment (ACME): Software User's Guide

    1996-01-01

    A user's guide for the Air Traffic Complexity Measurement Environment (ACME) software is presented. The ACME consists of two major components, a complexity analysis tool and user interface. The Complexity Analysis Tool (CAT) analyzes complexity off-line, producing data files which may be examined interactively via the Complexity Data Analysis Tool (CDAT). The Complexity Analysis Tool is composed of three independently executing processes that communicate via PVM (Parallel Virtual Machine) and Unix sockets. The Runtime Data Management and Control process (RUNDMC) extracts flight plan and track information from a SAR input file, and sends the information to GARP (Generate Aircraft Routes Process) and CAT (Complexity Analysis Task). GARP in turn generates aircraft trajectories, which are utilized by CAT to calculate sector complexity. CAT writes flight plan, track and complexity data to an output file, which can be examined interactively. The Complexity Data Analysis Tool (CDAT) provides an interactive graphic environment for examining the complexity data produced by the Complexity Analysis Tool (CAT). CDAT can also play back track data extracted from System Analysis Recording (SAR) tapes. The CDAT user interface consists of a primary window, a controls window, and miscellaneous pop-ups. Aircraft track and position data is displayed in the main viewing area of the primary window. The controls window contains miscellaneous control and display items. Complexity data is displayed in pop-up windows. CDAT plays back sector complexity and aircraft track and position data as a function of time. Controls are provided to start and stop playback, adjust the playback rate, and reposition the display to a specified time.

  8. Contribution of the collagen adhesin Acm to pathogenesis of Enterococcus faecium in experimental endocarditis.

    Nallapareddy, Sreedhar R; Singh, Kavindra V; Murray, Barbara E

    2008-09-01

    Enterococcus faecium is a multidrug-resistant opportunist causing difficult-to-treat nosocomial infections, including endocarditis, but there are no reports experimentally demonstrating E. faecium virulence determinants. Our previous studies showed that some clinical E. faecium isolates produce a cell wall-anchored collagen adhesin, Acm, and that an isogenic acm deletion mutant of the endocarditis-derived strain TX0082 lost collagen adherence. In this study, we show with a rat endocarditis model that TX0082 Deltaacm::cat is highly attenuated versus wild-type TX0082, both in established (72 h) vegetations (P Acm the first factor shown to be important for E. faecium pathogenesis. In contrast, no mortality differences were observed in a mouse peritonitis model. While 5 of 17 endocarditis isolates were Acm nonproducers and failed to adhere to collagen in vitro, all had an intact, highly conserved acm locus. Highly reduced acm mRNA levels (>or=50-fold reduction relative to an Acm producer) were found in three of these five nonadherent isolates, including the sequenced strain TX0016, by quantitative reverse transcription-PCR, indicating that acm transcription is downregulated in vitro in these isolates. However, examination of TX0016 cells obtained directly from infected rat vegetations by flow cytometry showed that Acm was present on 40% of cells grown during infection. Finally, we demonstrated a significant reduction in E. faecium collagen adherence by affinity-purified anti-Acm antibodies from E. faecium endocarditis patient sera, suggesting that Acm may be a potential immunotarget for strategies to control this emerging pathogen.

  9. Autolysis of Lactococcus lactis caused by induced overproduction of its major autolysin, AcmA

    Buist, Girbe; Karsens, H; Nauta, A; van Sinderen, D; Venema, G; Kok, J

    The optical density of a culture of Lactococcus lactis MG1363 was reduced more than 60% during prolonged stationary phase, Reduction in optical density (autolysis) was almost absent in a culture of an isogenic mutant containing a deletion in the major autolysin gene, acmA. An acmA mutant carrying

  10. Study on the percent of frequency of ACME-Arca in clinical isolates ...

    ACME is a mobile element of Arginine catabolic in Staphylococcus epidermidis that codes specific virulence factors. The purpose of this study was to examine the specific features and prevalence of ACME-arcA in the isolates of Staphylococcus epidermidis resistant to Methicillin isolated by clinical samples in Isfahan.

  11. Pomegranate MR images analysis using ACM and FCM algorithms

    Morad, Ghobad; Shamsi, Mousa; Sedaaghi, M. H.; Alsharif, M. R.

    2011-10-01

    Segmentation of an image plays an important role in image processing applications. In this paper segmentation of pomegranate magnetic resonance (MR) images has been explored. Pomegranate has healthy nutritional and medicinal properties for which the maturity indices and quality of internal tissues play an important role in the sorting process in which the admissible determination of features mentioned above cannot be easily achieved by human operator. Seeds and soft tissues are the main internal components of pomegranate. For research purposes, such as non-destructive investigation, in order to determine the ripening index and the percentage of seeds in growth period, segmentation of the internal structures should be performed as exactly as possible. In this paper, we present an automatic algorithm to segment the internal structure of pomegranate. Since its intensity of stem and calyx is close to the internal tissues, the stem and calyx pixels are usually labeled to the internal tissues by segmentation algorithm. To solve this problem, first, the fruit shape is extracted from its background using active contour model (ACM). Then stem and calyx are removed using morphological filters. Finally the image is segmented by fuzzy c-means (FCM). The experimental results represent an accuracy of 95.91% in the presence of stem and calyx, while the accuracy of segmentation increases to 97.53% when stem and calyx are first removed by morphological filters.

  12. VANET '13: Proceeding of the Tenth ACM International Workshop on Vehicular Inter-networking, Systems, and Applications

    Gozalvez, J.; Kargl, Frank; Mittag, J.; Kravets, R.; Tsai, M.; Unknown, [Unknown

    This year marks a very important date for the ACM international workshop on Vehicular inter-networking, systems, and applications as ACM VANET celebrates now its 10th edition. Starting in 2004 as "ACM international workshop on Vehicular ad hoc networks" already the change in title indicates that

  13. Characterization of a Novel Arginine Catabolic Mobile Element (ACME) and Staphylococcal Chromosomal Cassette mec Composite Island with Significant Homology to Staphylococcus epidermidis ACME type II in Methicillin-Resistant Staphylococcus aureus Genotype ST22-MRSA-IV.

    Shore, Anna C

    2011-02-22

    The arginine catabolic mobile element (ACME) is prevalent among ST8-MRSA-IVa (USA300) isolates and evidence suggests that ACME enhances the ability of ST8-MRSA-IVa to grow and survive on its host. ACME has been identified in a small number of isolates belonging to other MRSA clones but is widespread among coagulase-negative staphylococci (CoNS). This study reports the first description of ACME in two distinct strains of the pandemic ST22-MRSA-IV clone. A total of 238 MRSA isolates recovered in Ireland between 1971 and 2008 were investigated for ACME using a DNA microarray. Twenty-three isolates (9.7%) were ACME-positive, all were either MRSA genotype ST8-MRSA-IVa (7\\/23, 30%) or ST22-MRSA-IV (16\\/23, 70%). Whole-genome sequencing and comprehensive molecular characterization revealed the presence of a novel 46-kb ACME and SCCmec composite island (ACME\\/SCCmec-CI) in ST22-MRSA-IVh isolates (n = 15). This ACME\\/SCCmec-CI consists of a 12-kb DNA region previously identified in ACME type II in S. epidermidis ATCC 12228, a truncated copy of the J1 region of SCCmec I and a complete SCCmec IVh element. The composite island has a novel genetic organization with ACME located within orfX and SCCmec located downstream of ACME. One pvl-positive ST22-MRSA-IVa isolate carried ACME located downstream of SCCmec IVa as previously described in ST8-MRSA-IVa. These results suggest that ACME has been acquired by ST22-MRSA-IV on two independent occasions. At least one of these instances may have involved horizontal transfer and recombination events between MRSA and CoNS. The presence of ACME may enhance dissemination of ST22-MRSA-IV, an already successful MRSA clone.

  14. Inhibition of Enterococcus faecium adherence to collagen by antibodies against high-affinity binding subdomains of Acm.

    Nallapareddy, Sreedhar R; Sillanpää, Jouko; Ganesh, Vannakambadi K; Höök, Magnus; Murray, Barbara E

    2007-06-01

    Strains of Enterococcus faecium express a cell wall-anchored protein, Acm, which mediates adherence to collagen. Here, we (i) identify the minimal and high-affinity binding subsegments of Acm and (ii) show that anti-Acm immunoglobulin Gs (IgGs) purified against these subsegments reduced E. faecium TX2535 strain collagen adherence up to 73 and 50%, respectively, significantly more than the total IgGs against the full-length Acm A domain (28%) (P Acm adherence with functional subsegment-specific antibodies raises the possibility of their use as therapeutic or prophylactic agents.

  15. Comparative study of numerical schemes of TVD3, UNO3-ACM and optimized compact scheme

    Lee, Duck-Joo; Hwang, Chang-Jeon; Ko, Duck-Kon; Kim, Jae-Wook

    1995-01-01

    Three different schemes are employed to solve the benchmark problem. The first one is a conventional TVD-MUSCL (Monotone Upwind Schemes for Conservation Laws) scheme. The second scheme is a UNO3-ACM (Uniformly Non-Oscillatory Artificial Compression Method) scheme. The third scheme is an optimized compact finite difference scheme modified by us: the 4th order Runge Kutta time stepping, the 4th order pentadiagonal compact spatial discretization with the maximum resolution characteristics. The problems of category 1 are solved by using the second (UNO3-ACM) and third (Optimized Compact) schemes. The problems of category 2 are solved by using the first (TVD3) and second (UNO3-ACM) schemes. The problem of category 5 is solved by using the first (TVD3) scheme. It can be concluded from the present calculations that the Optimized Compact scheme and the UN03-ACM show good resolutions for category 1 and category 2 respectively.

  16. CNTF-ACM promotes mitochondrial respiration and oxidative stress in cortical neurons through upregulating L-type calcium channel activity.

    Sun, Meiqun; Liu, Hongli; Xu, Huanbai; Wang, Hongtao; Wang, Xiaojing

    2016-09-01

    A specialized culture medium termed ciliary neurotrophic factor-treated astrocyte-conditioned medium (CNTF-ACM) allows investigators to assess the peripheral effects of CNTF-induced activated astrocytes upon cultured neurons. CNTF-ACM has been shown to upregulate neuronal L-type calcium channel current activity, which has been previously linked to changes in mitochondrial respiration and oxidative stress. Therefore, the aim of this study was to evaluate CNTF-ACM's effects upon mitochondrial respiration and oxidative stress in rat cortical neurons. Cortical neurons, CNTF-ACM, and untreated control astrocyte-conditioned medium (UC-ACM) were prepared from neonatal Sprague-Dawley rat cortical tissue. Neurons were cultured in either CNTF-ACM or UC-ACM for a 48-h period. Changes in the following parameters before and after treatment with the L-type calcium channel blocker isradipine were assessed: (i) intracellular calcium levels, (ii) mitochondrial membrane potential (ΔΨm), (iii) oxygen consumption rate (OCR) and adenosine triphosphate (ATP) formation, (iv) intracellular nitric oxide (NO) levels, (v) mitochondrial reactive oxygen species (ROS) production, and (vi) susceptibility to the mitochondrial complex I toxin rotenone. CNTF-ACM neurons displayed the following significant changes relative to UC-ACM neurons: (i) increased intracellular calcium levels (p ACM (p ACM promotes mitochondrial respiration and oxidative stress in cortical neurons through elevating L-type calcium channel activity.

  17. The acellular matrix (ACM) for bladder tissue engineering: A quantitative magnetic resonance imaging study.

    Cheng, Hai-Ling Margaret; Loai, Yasir; Beaumont, Marine; Farhat, Walid A

    2010-08-01

    Bladder acellular matrices (ACMs) derived from natural tissue are gaining increasing attention for their role in tissue engineering and regeneration. Unlike conventional scaffolds based on biodegradable polymers or gels, ACMs possess native biomechanical and many acquired biologic properties. Efforts to optimize ACM-based scaffolds are ongoing and would be greatly assisted by a noninvasive means to characterize scaffold properties and monitor interaction with cells. MRI is well suited to this role, but research with MRI for scaffold characterization has been limited. This study presents initial results from quantitative MRI measurements for bladder ACM characterization and investigates the effects of incorporating hyaluronic acid, a natural biomaterial useful in tissue-engineering and regeneration. Measured MR relaxation times (T(1), T(2)) and diffusion coefficient were consistent with increased water uptake and glycosaminoglycan content observed on biochemistry in hyaluronic acid ACMs. Multicomponent MRI provided greater specificity, with diffusion data showing an acellular environment and T(2) components distinguishing the separate effects of increased glycosaminoglycans and hydration. These results suggest that quantitative MRI may provide useful information on matrix composition and structure, which is valuable in guiding further development using bladder ACMs for organ regeneration and in strategies involving the use of hyaluronic acid.

  18. Representation of deforestation impacts on climate, water, and nutrient cycles in the ACME earth system model

    Cai, X.; Riley, W. J.; Zhu, Q.

    2017-12-01

    Deforestation causes a series of changes to the climate, water, and nutrient cycles. Employing a state-of-the-art earth system model—ACME (Accelerated Climate Modeling for Energy), we comprehensively investigate the impacts of deforestation on these processes. We first assess the performance of the ACME Land Model (ALM) in simulating runoff, evapotranspiration, albedo, and plant productivity at 42 FLUXNET sites. The single column mode of ACME is then used to examine climate effects (temperature cooling/warming) and responses of runoff, evapotranspiration, and nutrient fluxes to deforestation. This approach separates local effects of deforestation from global circulation effects. To better understand the deforestation effects in a global context, we use the coupled (atmosphere, land, and slab ocean) mode of ACME to demonstrate the impacts of deforestation on global climate, water, and nutrient fluxes. Preliminary results showed that the land component of ACME has advantages in simulating these processes and that local deforestation has potentially large impacts on runoff and atmospheric processes.

  19. Listening to professional voices: draft 2 of the ACM code of ethics and professional conduct

    Flick, Catherine; Brinkman, Bo; Gotterbarn, D. W.; Miller, Keith; Vazansky, Kate; Wolf, Marty J.

    2017-01-01

    The file attached to this record is the author's final peer reviewed version. The Publisher's final version can be found by following the DOI link. For the first time since 1992, the ACM Code of Ethics and Professional Conduct (the Code) is being updated. The Code Update Task Force in conjunction with the Committee on Professional Ethics is seeking advice from ACM members on the update. We indicated many of the motivations for changing the Code when we shared Draft 1 of Code 2018 with the ...

  20. Theoretical interpretation of the nuclear structure of 88Se within the ACM and the QPM models.

    Gratchev, I. N.; Thiamova, G.; Alexa, P.; Simpson, G. S.; Ramdhane, M.

    2018-02-01

    The four-parameter algebraic collective model (ACM) Hamiltonian is used to describe the nuclear structure of 88Se. It is shown that the ACM is capable of providing a reasonable description of the excitation energies and relative positions of the ground-state band and γ band. The most probable interpretation of the nuclear structure of 88Se is that of a transitional nucleus. The Quasiparticle-plus-Phonon Model (QPM) was also applied to describe the nuclear motion in 88Se. Preliminarily calculations show that the collectivity of second excited state {2}2+ is weak and that this state contains a strong two-quasiparticle component.

  1. Characterization of a novel arginine catabolic mobile element (ACME) and staphylococcal chromosomal cassette mec composite island with significant homology to Staphylococcus epidermidis ACME type II in methicillin-resistant Staphylococcus aureus genotype ST22-MRSA-IV.

    Shore, Anna C

    2011-05-01

    The arginine catabolic mobile element (ACME) is prevalent among methicillin-resistant Staphylococcus aureus (MRSA) isolates of sequence type 8 (ST8) and staphylococcal chromosomal cassette mec (SCCmec) type IVa (USA300) (ST8-MRSA-IVa isolates), and evidence suggests that ACME enhances the ability of ST8-MRSA-IVa to grow and survive on its host. ACME has been identified in a small number of isolates belonging to other MRSA clones but is widespread among coagulase-negative staphylococci (CoNS). This study reports the first description of ACME in two distinct strains of the pandemic ST22-MRSA-IV clone. A total of 238 MRSA isolates recovered in Ireland between 1971 and 2008 were investigated for ACME using a DNA microarray. Twenty-three isolates (9.7%) were ACME positive, and all were either MRSA genotype ST8-MRSA-IVa (7\\/23, 30%) or MRSA genotype ST22-MRSA-IV (16\\/23, 70%). Whole-genome sequencing and comprehensive molecular characterization revealed the presence of a novel 46-kb ACME and staphylococcal chromosomal cassette mec (SCCmec) composite island (ACME\\/SCCmec-CI) in ST22-MRSA-IVh isolates (n=15). This ACME\\/SCCmec-CI consists of a 12-kb DNA region previously identified in ACME type II in S. epidermidis ATCC 12228, a truncated copy of the J1 region of SCCmec type I, and a complete SCCmec type IVh element. The composite island has a novel genetic organization, with ACME located within orfX and SCCmec located downstream of ACME. One PVL locus-positive ST22-MRSA-IVa isolate carried ACME located downstream of SCCmec type IVa, as previously described in ST8-MRSA-IVa. These results suggest that ACME has been acquired by ST22-MRSA-IV on two independent occasions. At least one of these instances may have involved horizontal transfer and recombination events between MRSA and CoNS. The presence of ACME may enhance dissemination of ST22-MRSA-IV, an already successful MRSA clone.

  2. Hypofractionated stereotactic radiotherapy (HFSRT) for who grade I anterior clinoid meningiomas (ACM).

    Demiral, Selcuk; Dincoglan, Ferrat; Sager, Omer; Gamsiz, Hakan; Uysal, Bora; Gundem, Esin; Elcim, Yelda; Dirican, Bahar; Beyzadeoglu, Murat

    2016-11-01

    While microsurgical resection plays a central role in the management of ACMs, extensive surgery may be associated with substantial morbidity particularly for tumors in intimate association with critical structures. In this study, we evaluated the use of HFSRT in the management of ACM. A total of 22 patients with ACM were treated using HFSRT. Frameless image guided volumetric modulated arc therapy (VMAT) was performed with a 6 MV linear accelerator (LINAC). The total dose was 25 Gy delivered in five fractions over five consecutive treatment days. Local control (LC) and progression free survival (PFS) rates were calculated using the Kaplan-Meier method. Common Terminology Criteria for Adverse Events, version 4.0 was used in toxicity grading. Out of the total 22 patients, outcomes of 19 patients with at least 36 months of periodic follow-up were assessed. Median patient age was 40 years old (range 24-77 years old). Median follow-up time was 53 months (range 36-63 months). LC and PFS rates were 100 and 89.4 % at 1 and 3 years, respectively. Only two patients (10.5 %) experienced clinical deterioration during the follow-up period. LINAC-based HFSRT offers high rates of LC and PFS for patients with ACMs.

  3. Proceedings of the 16th ACM SIGPLAN international conference on Functional programming

    Danvy, Olivier

    Welcome to the 16th ACM SIGPLAN International Conference on Functional Programming -- ICFP'11. The picture, on the front cover, is of Mount Fuji, seen from the 20th floor of the National Institute of Informatics (NII). It was taken by Sebastian Fischer in January 2011. In Japanese, the characters...

  4. Searching Spontaneous Conversational Speech. Proceedings of ACM SIGIR Workshop (SSCS2008)

    Köhler, J.; Larson, M; de Jong, Franciska M.G.; Ordelman, Roeland J.F.; Kraaij, W.

    2008-01-01

    The second workshop on Searching Spontaneous Conversational Speech (SSCS 2008) was held in Singapore on July 24, 2008 in conjunction with the 31st Annual International ACM SIGIR Conference. The goal of the workshop was to bring the speech community and the information retrieval community together.

  5. Validation of the Adolescent Concerns Measure (ACM): Evidence from Exploratory and Confirmatory Factor Analysis

    Ang, Rebecca P.; Chong, Wan Har; Huan, Vivien S.; Yeo, Lay See

    2007-01-01

    This article reports the development and initial validation of scores obtained from the Adolescent Concerns Measure (ACM), a scale which assesses concerns of Asian adolescent students. In Study 1, findings from exploratory factor analysis using 619 adolescents suggested a 24-item scale with four correlated factors--Family Concerns (9 items), Peer…

  6. ACME: A scalable parallel system for extracting frequent patterns from a very long sequence

    Sahli, Majed; Mansour, Essam; Kalnis, Panos

    2014-01-01

    -long sequences and is the first to support supermaximal motifs. ACME is a versatile parallel system that can be deployed on desktop multi-core systems, or on thousands of CPUs in the cloud. However, merely using more compute nodes does not guarantee efficiency

  7. ACME: A scalable parallel system for extracting frequent patterns from a very long sequence

    Sahli, Majed

    2014-10-02

    Modern applications, including bioinformatics, time series, and web log analysis, require the extraction of frequent patterns, called motifs, from one very long (i.e., several gigabytes) sequence. Existing approaches are either heuristics that are error-prone, or exact (also called combinatorial) methods that are extremely slow, therefore, applicable only to very small sequences (i.e., in the order of megabytes). This paper presents ACME, a combinatorial approach that scales to gigabyte-long sequences and is the first to support supermaximal motifs. ACME is a versatile parallel system that can be deployed on desktop multi-core systems, or on thousands of CPUs in the cloud. However, merely using more compute nodes does not guarantee efficiency, because of the related overheads. To this end, ACME introduces an automatic tuning mechanism that suggests the appropriate number of CPUs to utilize, in order to meet the user constraints in terms of run time, while minimizing the financial cost of cloud resources. Our experiments show that, compared to the state of the art, ACME supports three orders of magnitude longer sequences (e.g., DNA for the entire human genome); handles large alphabets (e.g., English alphabet for Wikipedia); scales out to 16,384 CPUs on a supercomputer; and supports elastic deployment in the cloud.

  8. Microstructure and chemical bonding of DLC films deposited on ACM rubber by PACVD

    Martinez-Martinez, D.; Schenkel, M.; Pei, Y.T.; Sánchez-López, J.C.; Hosson, J.Th.M. De

    2011-01-01

    The microstructure and chemical bonding of DLC films prepared by plasma assisted chemical vapor deposition on acrylic rubber (ACM) are studied in this paper. The temperature variation produced by the ion impingement during plasma cleaning and subsequent film deposition was used to modify the film

  9. ACME - Algorithms for Contact in a Multiphysics Environment API Version 1.0

    BROWN, KEVIN H.; SUMMERS, RANDALL M.; GLASS, MICHEAL W.; GULLERUD, ARNE S.; HEINSTEIN, MARTIN W.; JONES, REESE E.

    2001-01-01

    An effort is underway at Sandia National Laboratories to develop a library of algorithms to search for potential interactions between surfaces represented by analytic and discretized topological entities. This effort is also developing algorithms to determine forces due to these interactions for transient dynamics applications. This document describes the Application Programming Interface (API) for the ACME (Algorithms for Contact in a Multiphysics Environment) library

  10. Extra-Margins in ACM's Adjusted NMa ‘Mortgage-Rate-Calculation Method

    Dijkstra, M.; Schinkel, M.P.

    2013-01-01

    We analyse the development since 2004 of our concept of extra-margins on Dutch mortgages (Dijkstra & Schinkel, 2012), based on funding cost estimations in ACM (2013), which are an update of those in NMa (2011). Neither costs related to increased mortgage-specific risks, nor the inclusion of Basel

  11. Effects of activated ACM on expression of signal transducers in cerebral cortical neurons of rats.

    Wang, Xiaojing; Li, Zhengli; Zhu, Changgeng; Li, Zhongyu

    2007-06-01

    To explore the roles of astrocytes in the epileptogenesis, astrocytes and neurons were isolated, purified and cultured in vitro from cerebral cortex of rats. The astrocytes were activated by ciliary neurotrophic factor (CNTF) and astrocytic conditioned medium (ACM) was collected to treat neurons for 4, 8 and 12 h. By using Western blot, the expression of calmodulin dependent protein kinase II (CaMK II), inducible nitric oxide synthase (iNOS) and adenylate cyclase (AC) was detected in neurons. The results showed that the expression of CaMK II, iNOS and AC was increased significantly in the neurons treated with ACM from 4 h to 12 h (PACM and such signal pathways as NOS-NO-cGMP, Ca2+/CaM-CaMK II and AC-cAMP-PKA might take part in the signal transduction of epileptogenesis.

  12. Automated software system for checking the structure and format of ACM SIG documents

    Mirza, Arsalan Rahman; Sah, Melike

    2017-04-01

    Microsoft (MS) Office Word is one of the most commonly used software tools for creating documents. MS Word 2007 and above uses XML to represent the structure of MS Word documents. Metadata about the documents are automatically created using Office Open XML (OOXML) syntax. We develop a new framework, which is called ADFCS (Automated Document Format Checking System) that takes the advantage of the OOXML metadata, in order to extract semantic information from MS Office Word documents. In particular, we develop a new ontology for Association for Computing Machinery (ACM) Special Interested Group (SIG) documents for representing the structure and format of these documents by using OWL (Web Ontology Language). Then, the metadata is extracted automatically in RDF (Resource Description Framework) according to this ontology using the developed software. Finally, we generate extensive rules in order to infer whether the documents are formatted according to ACM SIG standards. This paper, introduces ACM SIG ontology, metadata extraction process, inference engine, ADFCS online user interface, system evaluation and user study evaluations.

  13. Model Diagnostics for the Department of Energy's Accelerated Climate Modeling for Energy (ACME) Project

    Smith, B.

    2015-12-01

    In 2014, eight Department of Energy (DOE) national laboratories, four academic institutions, one company, and the National Centre for Atmospheric Research combined forces in a project called Accelerated Climate Modeling for Energy (ACME) with the goal to speed Earth system model development for climate and energy. Over the planned 10-year span, the project will conduct simulations and modeling on DOE's most powerful high-performance computing systems at Oak Ridge, Argonne, and Lawrence Berkeley Leadership Compute Facilities. A key component of the ACME project is the development of an interactive test bed for the advanced Earth system model. Its execution infrastructure will accelerate model development and testing cycles. The ACME Workflow Group is leading the efforts to automate labor-intensive tasks, provide intelligent support for complex tasks and reduce duplication of effort through collaboration support. As part of this new workflow environment, we have created a diagnostic, metric, and intercomparison Python framework, called UVCMetrics, to aid in the testing-to-production execution of the ACME model. The framework exploits similarities among different diagnostics to compactly support diagnosis of new models. It presently focuses on atmosphere and land but is designed to support ocean and sea ice model components as well. This framework is built on top of the existing open-source software framework known as the Ultrascale Visualization Climate Data Analysis Tools (UV-CDAT). Because of its flexible framework design, scientists and modelers now can generate thousands of possible diagnostic outputs. These diagnostics can compare model runs, compare model vs. observation, or simply verify a model is physically realistic. Additional diagnostics are easily integrated into the framework, and our users have already added several. Diagnostics can be generated, viewed, and manipulated from the UV-CDAT graphical user interface, Python command line scripts and programs

  14. Molecular characteristics of clinical methicillin-resistant Staphylococcus pseudintermedius harboring arginine catabolic mobile element (ACME) from dogs and cats.

    Yang, Ching; Wan, Min-Tao; Lauderdale, Tsai-Ling; Yeh, Kuang-Sheng; Chen, Charles; Hsiao, Yun-Hsia; Chou, Chin-Cheng

    2017-06-01

    This study aimed to investigate the presence of arginine catabolic mobile element (ACME) and its associated molecular characteristics in methicillin-resistant Staphylococcus pseudintermedius (MRSP). Among the 72 S. pseudintermedius recovered from various infection sites of dogs and cats, 52 (72.2%) were MRSP. ACME-arcA was detected commonly (69.2%) in these MRSP isolates, and was more frequently detected in those from the skin than from other body sites (P=0.047). There was a wide genetic diversity among the ACME-arcA-positive MRSP isolates, which comprised three SCCmec types (II-III, III and V) and 15 dru types with two predominant clusters (9a and 11a). Most MRSP isolates were multidrug-resistant. Since S. pseudintermedius could serve as a reservoir of ACME, further research on this putative virulence factor is recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Transient Inverse Calibration of the Site-Wide Groundwater Flow Model (ACM-2): FY03 Progress Report

    Vermeul, Vince R.; Bergeron, Marcel P.; Cole, C R.; Murray, Christopher J.; Nichols, William E.; Scheibe, Timothy D.; Thorne, Paul D.; Waichler, Scott R.; Xie, YuLong

    2003-01-01

    DOE and PNNL are working to strengthen the technical defensibility of the groundwater flow and transport model at the Hanford Site and to incorporate uncertainty into the model. One aspect of the initiative is developing and using a three-dimensional transient inverse model to estimate the hydraulic conductivities, specific yields, and other parameters using data from Hanford since 1943. The focus of the alternative conceptual model (ACM-2) inverse modeling initiative documented in this report was to address limitations identified in the ACM-1 model, complete the facies-based approach for representing the hydraulic conductivity distribution in the Hanford and middle Ringold Formations, develop the approach and implementation methodology for generating multiple ACMs based on geostatistical data analysis, and develop an approach for inverse modeling of these stochastic ACMs. The primary modifications to ACM-2 transient inverse model include facies-based zonation of Units 1 (Hanford ) and 5 (middle Ringold); an improved approach for handling run-on recharge from upland areas based on watershed modeling results; an improved approach for representing artificial discharges from site operations; and minor changes to the geologic conceptual model. ACM-2 is the first attempt to fully incorporate the facies-based approach to represent the hydrogeologic structure. Further refinement and additional improvements to overall model fit will be realized during future inverse simulations of groundwater flow and transport. In addition, preliminary work was completed on an approach and implementation for generating an inverse modeling of stochastic ACMs. These techniques were applied to assess the uncertainty in the facies-based zonation of the Hanford formation and the geological structure of Ringold mud units. The geostatistical analysis used a preliminary interpretation of the facies-based zonation that was not consistent with that used in ACM-2. Although the overall objective of

  16. Timely activation of budding yeast APCCdh1 involves degradation of its inhibitor, Acm1, by an unconventional proteolytic mechanism.

    Michael Melesse

    Full Text Available Regulated proteolysis mediated by the ubiquitin proteasome system is a fundamental and essential feature of the eukaryotic cell division cycle. Most proteins with cell cycle-regulated stability are targeted for degradation by one of two related ubiquitin ligases, the Skp1-cullin-F box protein (SCF complex or the anaphase-promoting complex (APC. Here we describe an unconventional cell cycle-regulated proteolytic mechanism that acts on the Acm1 protein, an inhibitor of the APC activator Cdh1 in budding yeast. Although Acm1 can be recognized as a substrate by the Cdc20-activated APC (APCCdc20 in anaphase, APCCdc20 is neither necessary nor sufficient for complete Acm1 degradation at the end of mitosis. An APC-independent, but 26S proteasome-dependent, mechanism is sufficient for complete Acm1 clearance from late mitotic and G1 cells. Surprisingly, this mechanism appears distinct from the canonical ubiquitin targeting pathway, exhibiting several features of ubiquitin-independent proteasomal degradation. For example, Acm1 degradation in G1 requires neither lysine residues in Acm1 nor assembly of polyubiquitin chains. Acm1 was stabilized though by conditional inactivation of the ubiquitin activating enzyme Uba1, implying some requirement for the ubiquitin pathway, either direct or indirect. We identified an amino terminal predicted disordered region in Acm1 that contributes to its proteolysis in G1. Although ubiquitin-independent proteasome substrates have been described, Acm1 appears unique in that its sensitivity to this mechanism is strictly cell cycle-regulated via cyclin-dependent kinase (Cdk phosphorylation. As a result, Acm1 expression is limited to the cell cycle window in which Cdk is active. We provide evidence that failure to eliminate Acm1 impairs activation of APCCdh1 at mitotic exit, justifying its strict regulation by cell cycle-dependent transcription and proteolytic mechanisms. Importantly, our results reveal that strict cell

  17. Timely Activation of Budding Yeast APCCdh1 Involves Degradation of Its Inhibitor, Acm1, by an Unconventional Proteolytic Mechanism

    Melesse, Michael; Choi, Eunyoung; Hall, Hana; Walsh, Michael J.; Geer, M. Ariel; Hall, Mark C.

    2014-01-01

    Regulated proteolysis mediated by the ubiquitin proteasome system is a fundamental and essential feature of the eukaryotic cell division cycle. Most proteins with cell cycle-regulated stability are targeted for degradation by one of two related ubiquitin ligases, the Skp1-cullin-F box protein (SCF) complex or the anaphase-promoting complex (APC). Here we describe an unconventional cell cycle-regulated proteolytic mechanism that acts on the Acm1 protein, an inhibitor of the APC activator Cdh1 in budding yeast. Although Acm1 can be recognized as a substrate by the Cdc20-activated APC (APCCdc20) in anaphase, APCCdc20 is neither necessary nor sufficient for complete Acm1 degradation at the end of mitosis. An APC-independent, but 26S proteasome-dependent, mechanism is sufficient for complete Acm1 clearance from late mitotic and G1 cells. Surprisingly, this mechanism appears distinct from the canonical ubiquitin targeting pathway, exhibiting several features of ubiquitin-independent proteasomal degradation. For example, Acm1 degradation in G1 requires neither lysine residues in Acm1 nor assembly of polyubiquitin chains. Acm1 was stabilized though by conditional inactivation of the ubiquitin activating enzyme Uba1, implying some requirement for the ubiquitin pathway, either direct or indirect. We identified an amino terminal predicted disordered region in Acm1 that contributes to its proteolysis in G1. Although ubiquitin-independent proteasome substrates have been described, Acm1 appears unique in that its sensitivity to this mechanism is strictly cell cycle-regulated via cyclin-dependent kinase (Cdk) phosphorylation. As a result, Acm1 expression is limited to the cell cycle window in which Cdk is active. We provide evidence that failure to eliminate Acm1 impairs activation of APCCdh1 at mitotic exit, justifying its strict regulation by cell cycle-dependent transcription and proteolytic mechanisms. Importantly, our results reveal that strict cell-cycle expression profiles

  18. TWO NOVEL ACM (ACTIVE CONTOUR MODEL) METHODS FOR INTRAVASCULAR ULTRASOUND IMAGE SEGMENTATION

    Chen, Chi Hau; Potdat, Labhesh; Chittineni, Rakesh

    2010-01-01

    One of the attractive image segmentation methods is the Active Contour Model (ACM) which has been widely used in medical imaging as it always produces sub-regions with continuous boundaries. Intravascular ultrasound (IVUS) is a catheter based medical imaging technique which is used for quantitative assessment of atherosclerotic disease. Two methods of ACM realizations are presented in this paper. The gradient descent flow based on minimizing energy functional can be used for segmentation of IVUS images. However this local operation alone may not be adequate to work with the complex IVUS images. The first method presented consists of basically combining the local geodesic active contours and global region-based active contours. The advantage of combining the local and global operations is to allow curves deforming under the energy to find only significant local minima and delineate object borders despite noise, poor edge information and heterogeneous intensity profiles. Results for this algorithm are compared to standard techniques to demonstrate the method's robustness and accuracy. In the second method, the energy function is appropriately modified and minimized using a Hopfield neural network. Proper modifications in the definition of the bias of the neurons have been introduced to incorporate image characteristics. The method overcomes distortions in the expected image pattern, such as due to the presence of calcium, and employs a specialized structure of the neural network and boundary correction schemes which are based on a priori knowledge about the vessel geometry. The presented method is very fast and has been evaluated using sequences of IVUS frames.

  19. Clinical isolates of Enterococcus faecium exhibit strain-specific collagen binding mediated by Acm, a new member of the MSCRAMM family.

    Nallapareddy, Sreedhar R; Weinstock, George M; Murray, Barbara E

    2003-03-01

    A collagen-binding adhesin of Enterococcus faecium, Acm, was identified. Acm shows 62% similarity to the Staphylococcus aureus collagen adhesin Cna over the entire protein and is more similar to Cna (60% and 75% similarity with Cna A and B domains respectively) than to the Enterococcus faecalis collagen-binding adhesin, Ace, which shares homology with Acm only in the A domain. Despite the detection of acm in 32 out of 32 E. faecium isolates, only 11 of these (all clinical isolates, including four vancomycin-resistant endocarditis isolates and seven other isolates) exhibited binding to collagen type I (CI). Although acm from three CI-binding vancomycin-resistant E. faecium clinical isolates showed 100% identity, analysis of acm genes and their promoter regions from six non-CI-binding strains identified deletions or mutations that introduced stop codons and/or IS elements within the gene or the promoter region in five out of six strains, suggesting that the presence of an intact functional acm gene is necessary for binding of E. faecium strains to CI. Recombinant Acm A domain showed specific and concentration-dependent binding to collagen, and this protein competed with E. faecium binding to immobilized CI. Consistent with the adherence phenotype and sequence data, probing with Acm-specific IgGs purified from anti-recombinant Acm A polyclonal rabbit serum confirmed the surface expression of Acm in three out of three collagen-binding clinical isolates of E. faecium tested, but in none of the strains with a non-functional pseudo acm gene. Introduction of a functional acm gene into two non-CI-binding natural acm mutant strains conferred a CI-binding phenotype, further confirming that native Acm is sufficient for the binding of E. faecium to CI. These results demonstrate that acm, which encodes a potential virulence factor, is functional only in certain infection-derived clinical isolates of E. faecium, and suggest that Acm is the primary adhesin responsible for the

  20. Formation of personality’s acme-qualities as a component of physical education specialists’ acmeological competence

    T.Hr. Dereka

    2016-10-01

    Full Text Available Purpose: to determine characteristics of acme-qualities’ formation in physical education specialists and determine correlations between components. Material: in the research students of “Physical education” specialty (n=194 participated. For assessment personality’s qualities special tests were used. Organization abilities, communicative abilities, creative potential, demand in achievement, emotional information level, control of emotions and etc. were assessed. Results: we determined components of personality’s acme-competence component in physical education specialists. We found density and orientation of correlation and influence of acme-qualities on personality’s component. By the results of factorial analysis we grouped, classified components by four factors and created their visual picture. The accumulated percentage of the studied factors’ dispersion was determined. Conclusions: continuous professional training of physical education specialists on acme-principles resulted in formation of personality’s acme-qualities. They facilitate manifestation of personality’s activity in the process of professional formation and constant self-perfection.

  1. An Unexpected Location of the Arginine Catabolic Mobile Element (ACME) in a USA300-Related MRSA Strain

    Damkjær Bartels, Mette; Hansen, Lars H.; Boye, Kit

    2011-01-01

    In methicillin resistant Staphylococcus aureus (MRSA), the arginine catabolic mobile element (ACME) was initially described in USA300 (t008-ST8) where it is located downstream of the staphylococcal cassette chromosome mec (SCCmec). A common health-care associated MRSA in Copenhagen, Denmark (t024......-ST8) is clonally related to USA300 and is frequently PCR positive for the ACME specific arcA-gene. This study is the first to describe an ACME element upstream of the SCCmec in MRSA. By traditional SCCmec typing schemes, the SCCmec of t024-ST8 strain M1 carries SCCmec IVa, but full sequencing...... of SCCmec, M1 had two new DR between the orfX gene and the J3 region of the SCCmec. The region between the orfX DR (DR1) and DR2 contained the ccrAB4 genes. An ACME II-like element was located between DR2 and DR3. The entire 26,468 bp sequence between DR1 and DR3 was highly similar to parts of the ACME...

  2. On-resin conversion of Cys(Acm)-containing peptides to their corresponding Cys(Scm) congeners.

    Mullen, Daniel G; Weigel, Benjamin; Barany, George; Distefano, Mark D

    2010-05-01

    The Acm protecting group for the thiol functionality of cysteine is removed under conditions (Hg(2+)) that are orthogonal to the acidic milieu used for global deprotection in Fmoc-based solid-phase peptide synthesis. This use of a toxic heavy metal for deprotection has limited the usefulness of Acm in peptide synthesis. The Acm group may be converted to the Scm derivative that can then be used as a reactive intermediate for unsymmetrical disulfide formation. It may also be removed by mild reductive conditions to generate unprotected cysteine. Conversion of Cys(Acm)-containing peptides to their corresponding Cys(Scm) derivatives in solution is often problematic because the sulfenyl chloride reagent used for this conversion may react with the sensitive amino acids tyrosine and tryptophan. In this protocol, we report a method for on-resin Acm to Scm conversion that allows the preparation of Cys(Scm)-containing peptides under conditions that do not modify other amino acids. (c) 2010 European Peptide Society and John Wiley & Sons, Ltd.

  3. ADAPTIF CONSERVATION (ACM MODEL IN INCREASING FAMILY SUPPORT AND COMPLIANCE TREATMENT IN PATIENT WITH PULONARY TUBERCULOSIS IN SURABAYA CITY REGION

    Siti Nur Kholifah

    2017-04-01

    Full Text Available Introduction: Tuberculosis (TB in Indonesia is still health problem and the prevalence rate is high. Discontinuing medication and lack of family support are the causalities. Numbers of strategies to overcome are seemingly not succeeded. Roles and responsibilities of family nursing are crucial to improve participation, motivation of individual, family and community in prevention, including pulmonary tuberculosis. Unfortunately, models of pulmonary tuberculosis currently unavailable. The combination of adaptation and conservation in complementarily improving family support and compliance in medication is introduced in this study. Method: This research intended to analyze Adaptive Conservation Model (ACM in extending family support and treatment compliance. Modeling steps including model analysis, expert validation, field trial, implementation and recommending the output model. Research subject involves 15 families who implement family Assistance and supervision in Medication (ASM and other 15 families with ACM. Result: The study revealed ACM is better than ASM on the case of family support and medication compliances. It supports the role of environment as influential factor on individual health belief, values and decision making. Therefore, it is advised to apply ACM in enhancing family support and compliance of pulmonary TB patients. Discussion: Social and family supports to ACM group obtained by developing interaction through communication. Family interaction necessary to improve family support to pulmonary tuberculosis patients. And social support plays as motivator to maintain compliance on medication

  4. Comparison of the chemical behaviour of humanized ACMS VS. Human IGG radiolabeled with 99mTc

    Rivero Santamaria, Alejandro; Zayas Crespo, Francisco; Mesa Duennas, Niurka; Castillo Vitloch, Adolfo J.

    2003-01-01

    The purpose of this work is to compare the chemical behaviour of humanized AcMs vs. human IgG radiolabeled with 99 mTc. to this end, 3 immunoglobulins were analyzed, the IgG (human), the humanized monoclonal antibody R3 (Acm-R3h) and the humanized monoclonal antibody T1. The results obtained reveal slight differences as regards the behaviour of theses immunoglobulins before the labelling with 99T c, which shows differences in the chemical behaviour of these proteins. Although in theory the modifications that are made to the AcMs in order to humanize them must not affect their chemical behaviour, the obtained data indicate that the conditions for their radiolabelling should not be extrapolated from other proteins; on the contrary, particular procedures should be elaborated for each AcM-h

  5. AcmB Is an S-Layer-Associated β-N-Acetylglucosaminidase and Functional Autolysin in Lactobacillus acidophilus NCFM.

    Johnson, Brant R; Klaenhammer, Todd R

    2016-09-15

    Autolysins, also known as peptidoglycan hydrolases, are enzymes that hydrolyze specific bonds within bacterial cell wall peptidoglycan during cell division and daughter cell separation. Within the genome of Lactobacillus acidophilus NCFM, there are 11 genes encoding proteins with peptidoglycan hydrolase catalytic domains, 9 of which are predicted to be functional. Notably, 5 of the 9 putative autolysins in L. acidophilus NCFM are S-layer-associated proteins (SLAPs) noncovalently colocalized along with the surface (S)-layer at the cell surface. One of these SLAPs, AcmB, a β-N-acetylglucosaminidase encoded by the gene lba0176 (acmB), was selected for functional analysis. In silico analysis revealed that acmB orthologs are found exclusively in S-layer- forming species of Lactobacillus Chromosomal deletion of acmB resulted in aberrant cell division, autolysis, and autoaggregation. Complementation of acmB in the ΔacmB mutant restored the wild-type phenotype, confirming the role of this SLAP in cell division. The absence of AcmB within the exoproteome had a pleiotropic effect on the extracellular proteins covalently and noncovalently bound to the peptidoglycan, which likely led to the observed decrease in the binding capacity of the ΔacmB strain for mucin and extracellular matrices fibronectin, laminin, and collagen in vitro These data suggest a functional association between the S-layer and the multiple autolysins noncovalently colocalized at the cell surface of L. acidophilus NCFM and other S-layer-producing Lactobacillus species. Lactobacillus acidophilus is one of the most widely used probiotic microbes incorporated in many dairy foods and dietary supplements. This organism produces a surface (S)-layer, which is a self-assembling crystalline array found as the outermost layer of the cell wall. The S-layer, along with colocalized associated proteins, is an important mediator of probiotic activity through intestinal adhesion and modulation of the mucosal immune

  6. Improving simulated spatial distribution of productivity and biomass in Amazon forests using the ACME land model

    Yang, X.; Thornton, P. E.; Ricciuto, D. M.; Shi, X.; Xu, M.; Hoffman, F. M.; Norby, R. J.

    2017-12-01

    Tropical forests play a crucial role in the global carbon cycle, accounting for one third of the global NPP and containing about 25% of global vegetation biomass and soil carbon. This is particularly true for tropical forests in the Amazon region, as it comprises approximately 50% of the world's tropical forests. It is therefore important for us to understand and represent the processes that determine the fluxes and storage of carbon in these forests. In this study, we show that the implementation of phosphorus (P) cycle and P limitation in the ACME Land Model (ALM) improves simulated spatial pattern of NPP. The P-enabled ALM is able to capture the west-to-east gradient of productivity, consistent with field observations. We also show that by improving the representation of mortality processes, ALM is able to reproduce the observed spatial pattern of above ground biomass across the Amazon region.

  7. Can Pearlite form Outside of the Hultgren Extrapolation of the Ae3 and Acm Phase Boundaries?

    Aranda, M. M.; Rementeria, R.; Capdevila, C.; Hackenberg, R. E.

    2016-02-01

    It is usually assumed that ferrous pearlite can form only when the average austenite carbon concentration C 0 lies between the extrapolated Ae3 ( γ/ α) and Acm ( γ/ θ) phase boundaries (the "Hultgren extrapolation"). This "mutual supersaturation" criterion for cooperative lamellar nucleation and growth is critically examined from a historical perspective and in light of recent experiments on coarse-grained hypoeutectoid steels which show pearlite formation outside the Hultgren extrapolation. This criterion, at least as interpreted in terms of the average austenite composition, is shown to be unnecessarily restrictive. The carbon fluxes evaluated from Brandt's solution are sufficient to allow pearlite growth both inside and outside the Hultgren Extrapolation. As for the feasibility of the nucleation events leading to pearlite, the only criterion is that there are some local regions of austenite inside the Hultgren Extrapolation, even if the average austenite composition is outside.

  8. Preventive maintenance plan of the air-conditioning duct using the ACM-sensor

    Fukuba, Kazushi; Ito, Takanobu; Kojima, Akiko; Tanji, Kazuhiro; Sato, Yuki

    2013-01-01

    Air-conditioning duct is difficult to predict the date to occur of corrosion such as affect the function. Therefore, the current conservation method is mostly corrective maintenance. Therefore, we used the test pieces of six types and ACM-sensor in order to solve the corrosion speed from corrosion environment and relationship of corrosion quantity of test pieces. In addition, was used the duct molded articles various in order to check the corrosion degree of when processed the duct. As a result, we were selected crust body constituting a duct and optimal combination of the flange by solve the corrosion speed of the test pieces various. Thus, it performs preventive disposal before to occur of corrosion such as affect the function by predicting the duct life from corrosion speed, and lead to stability and safe operating by appropriate maintenance of equipment. (author)

  9. Additive Construction with Mobile Emplacement (ACME) / Automated Construction of Expeditionary Structures (ACES) Materials Delivery System (MDS)

    Mueller, R. P.; Townsend, I. I.; Tamasy, G. J.; Evers, C. J.; Sibille, L. J.; Edmunson, J. E.; Fiske, M. R.; Fikes, J. C.; Case, M.

    2018-01-01

    The purpose of the Automated Construction of Expeditionary Structures, Phase 3 (ACES 3) project is to incorporate the Liquid Goods Delivery System (LGDS) into the Dry Goods Delivery System (DGDS) structure to create an integrated and automated Materials Delivery System (MDS) for 3D printing structures with ordinary Portland cement (OPC) concrete. ACES 3 is a prototype for 3-D printing barracks for soldiers in forward bases, here on Earth. The LGDS supports ACES 3 by storing liquid materials, mixing recipe batches of liquid materials, and working with the Dry Goods Feed System (DGFS) previously developed for ACES 2, combining the materials that are eventually extruded out of the print nozzle. Automated Construction of Expeditionary Structures, Phase 3 (ACES 3) is a project led by the US Army Corps of Engineers (USACE) and supported by NASA. The equivalent 3D printing system for construction in space is designated Additive Construction with Mobile Emplacement (ACME) by NASA.

  10. Autonomic Cluster Management System (ACMS): A Demonstration of Autonomic Principles at Work

    Baldassari, James D.; Kopec, Christopher L.; Leshay, Eric S.; Truszkowski, Walt; Finkel, David

    2005-01-01

    Cluster computing, whereby a large number of simple processors or nodes are combined together to apparently function as a single powerful computer, has emerged as a research area in its own right. The approach offers a relatively inexpensive means of achieving significant computational capabilities for high-performance computing applications, while simultaneously affording the ability to. increase that capability simply by adding more (inexpensive) processors. However, the task of manually managing and con.guring a cluster quickly becomes impossible as the cluster grows in size. Autonomic computing is a relatively new approach to managing complex systems that can potentially solve many of the problems inherent in cluster management. We describe the development of a prototype Automatic Cluster Management System (ACMS) that exploits autonomic properties in automating cluster management.

  11. ARM Airborne Carbon Measurements VI (ARM-ACME VI) Field Campaign Report

    Biraud, Sebastien [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2017-05-01

    From October 1, 2015 through September 30, 2016, AAF deployed a Cessna 206 aircraft over the Southern Great Plains, collecting observations of trace gas mixing ratios over the ARM/SGP Central Facility. The aircraft payload included two Atmospheric Observing Systems (AOS Inc.) analyzers for continuous measurements of CO2, and a 12-flask sampler for analysis of carbon cycle gases (CO2, CO, CH4, N2O, 13CO2). The aircraft payload also includes solar/infrared radiation measurements. This research (supported by DOE ARM and TES programs) builds upon previous ARM-ACME missions. The goal of these measurements is to improve understanding of: (a) the carbon exchange of the ARM region; (b) how CO2 and associated water and energy fluxes influence radiative forcing, convective processes, and CO2 concentrations over the ARM region, and (c) how greenhouse gases are transported on continental scales.

  12. A functional collagen adhesin gene, acm, in clinical isolates of Enterococcus faecium correlates with the recent success of this emerging nosocomial pathogen.

    Nallapareddy, Sreedhar R; Singh, Kavindra V; Okhuysen, Pablo C; Murray, Barbara E

    2008-09-01

    Enterococcus faecium recently evolved from a generally avirulent commensal into a multidrug-resistant health care-associated pathogen causing difficult-to-treat infections, but little is known about the factors responsible for this change. We previously showed that some E. faecium strains express a cell wall-anchored collagen adhesin, Acm. Here we analyzed 90 E. faecium isolates (99% acm(+)) and found that the Acm protein was detected predominantly in clinically derived isolates, while the acm gene was present as a transposon-interrupted pseudogene in 12 of 47 isolates of nonclinical origin. A highly significant association between clinical (versus fecal or food) origin and collagen adherence (P Acm detected by whole-cell enzyme-linked immunosorbent assay and flow cytometry. Thirty-seven of 41 sera from patients with E. faecium infections showed reactivity with recombinant Acm, while only 4 of 30 community and hospitalized patient control group sera reacted (P Acm were present in all 14 E. faecium endocarditis patient sera. Although pulsed-field gel electrophoresis indicated that multiple strains expressed collagen adherence, multilocus sequence typing demonstrated that the majority of collagen-adhering isolates, as well as 16 of 17 endocarditis isolates, are part of the hospital-associated E. faecium genogroup referred to as clonal complex 17 (CC17), which has emerged globally. Taken together, our findings support the hypothesis that Acm has contributed to the emergence of E. faecium and CC17 in nosocomial infections.

  13. HT 2011 : Proceedings of the 22nd ACM Conference on Hypertext and Hypermedia, Eindhoven, The Netherlands, June 6-9, 2011

    De Bra, P.M.E.; Gronbak, K.

    2011-01-01

    Foreword. It is our great pleasure to welcome you to ACM Hypertext 2011, the 22nd ACM Conference on Hypertext and Hypermedia, and to the "Land of the Innovator", the campus of the Eindhoven University of Technology, located in the "city of light" Eindhoven, the Netherlands. Hypertext is an exciting

  14. Selective desulfurization of cysteine in the presence of Cys(Acm) in polypeptides obtained by native chemical ligation.

    Pentelute, Brad L; Kent, Stephen B H

    2007-02-15

    Increased versatility for the synthesis of proteins and peptides by native chemical ligation requires the ability to ligate at positions other than Cys. Here, we report that Raney nickel can be used under standard conditions for the selective desulfurization of Cys in the presence of Cys(Acm). This simple and practical tactic enables the more common Xaa-Ala junctions to be used as ligation sites for the chemical synthesis of Cys-containing peptides and proteins. [reaction: see text].

  15. Segmentation of solid subregion of high grade gliomas in MRI images based on active contour model (ACM)

    Seow, P.; Win, M. T.; Wong, J. H. D.; Abdullah, N. A.; Ramli, N.

    2016-03-01

    Gliomas are tumours arising from the interstitial tissue of the brain which are heterogeneous, infiltrative and possess ill-defined borders. Tumour subregions (e.g. solid enhancing part, edema and necrosis) are often used for tumour characterisation. Tumour demarcation into substructures facilitates glioma staging and provides essential information. Manual segmentation had several drawbacks that include laborious, time consuming, subjected to intra and inter-rater variability and hindered by diversity in the appearance of tumour tissues. In this work, active contour model (ACM) was used to segment the solid enhancing subregion of the tumour. 2D brain image acquisition data using 3T MRI fast spoiled gradient echo sequence in post gadolinium of four histologically proven high-grade glioma patients were obtained. Preprocessing of the images which includes subtraction and skull stripping were performed and then followed by ACM segmentation. The results of the automatic segmentation method were compared against the manual delineation of the tumour by a trainee radiologist. Both results were further validated by an experienced neuroradiologist and a brief quantitative evaluations (pixel area and difference ratio) were performed. Preliminary results of the clinical data showed the potential of ACM model in the application of fast and large scale tumour segmentation in medical imaging.

  16. Segmentation of solid subregion of high grade gliomas in MRI images based on active contour model (ACM)

    Seow, P; Win, M T; Wong, J H D; Ramli, N; Abdullah, N A

    2016-01-01

    Gliomas are tumours arising from the interstitial tissue of the brain which are heterogeneous, infiltrative and possess ill-defined borders. Tumour subregions (e.g. solid enhancing part, edema and necrosis) are often used for tumour characterisation. Tumour demarcation into substructures facilitates glioma staging and provides essential information. Manual segmentation had several drawbacks that include laborious, time consuming, subjected to intra and inter-rater variability and hindered by diversity in the appearance of tumour tissues. In this work, active contour model (ACM) was used to segment the solid enhancing subregion of the tumour. 2D brain image acquisition data using 3T MRI fast spoiled gradient echo sequence in post gadolinium of four histologically proven high-grade glioma patients were obtained. Preprocessing of the images which includes subtraction and skull stripping were performed and then followed by ACM segmentation. The results of the automatic segmentation method were compared against the manual delineation of the tumour by a trainee radiologist. Both results were further validated by an experienced neuroradiologist and a brief quantitative evaluations (pixel area and difference ratio) were performed. Preliminary results of the clinical data showed the potential of ACM model in the application of fast and large scale tumour segmentation in medical imaging. (paper)

  17. Recent changes in flood damage in the United States from observations and ACME model

    Leng, G.; Leung, L. R.

    2017-12-01

    Despite efforts to mitigate flood hazards in flood-prone areas, survey- and report-based flood databases show that flood damage has increased and emerged as one of the most costly disaster in the United States since the 1990s. Understanding the mechanism driving the changes in flood damage is therefore critical for reducing flood risk. In this study, we first conduct a comprehensive analysis of the changing characteristics of flood damage at local, state and country level. Results show a significant increasing trend in the number of flood hazards, causing economic losses of up to $7 billion per year. The ratio of flood events that caused tangible economical cost to the total flood events has exhibited a non-significant increasing trend before 2007 followed by a significant decrease, indicating a changing vulnerability to floods. Analysis also reveals distinct spatial and temporal patterns in the threshold intensity of flood hazards with tangible economical cost. To understand the mechanism behind the increasing flood damage, we develop a flood damage economic model coupled with the integrated hydrological modeling system of ACME that features a river routing model with an inundation parameterization and a water use and regulation model. The model is evaluated over the country against historical records. Several numerical experiments are then designed to explore the mechanisms behind the recent changes in flood damage from the perspective of flood hazard, exposure and vulnerability, which constitute flood damage. The role of human activities such as reservoir operations and water use in modifying regional floods are also explored using the new tool, with the goal of improving understanding and modeling of vulnerability to flood hazards.

  18. A mechanistic diagnosis of the simulation of soil CO2 efflux of the ACME Land Model

    Liang, J.; Ricciuto, D. M.; Wang, G.; Gu, L.; Hanson, P. J.; Mayes, M. A.

    2017-12-01

    Accurate simulation of the CO2 efflux from soils (i.e., soil respiration) to the atmosphere is critical to project global biogeochemical cycles and the magnitude of climate change in Earth system models (ESMs). Currently, the simulated soil respiration by ESMs still have a large uncertainty. In this study, a mechanistic diagnosis of soil respiration in the Accelerated Climate Model for Energy (ACME) Land Model (ALM) was conducted using long-term observations at the Missouri Ozark AmeriFlux (MOFLUX) forest site in the central U.S. The results showed that the ALM default run significantly underestimated annual soil respiration and gross primary production (GPP), while incorrectly estimating soil water potential. Improved simulations of soil water potential with site-specific data significantly improved the modeled annual soil respiration, primarily because annual GPP was simultaneously improved. Therefore, accurate simulations of soil water potential must be carefully calibrated in ESMs. Despite improved annual soil respiration, the ALM continued to underestimate soil respiration during peak growing seasons, and to overestimate soil respiration during non-peak growing seasons. Simulations involving increased GPP during peak growing seasons increased soil respiration, while neither improved plant phenology nor increased temperature sensitivity affected the simulation of soil respiration during non-peak growing seasons. One potential reason for the overestimation of the soil respiration during non-peak growing seasons may be that the current model structure is substrate-limited, while microbial dormancy under stress may cause the system to become decomposer-limited. Further studies with more microbial data are required to provide adequate representation of soil respiration and to understand the underlying reasons for inaccurate model simulations.

  19. A Novel Observation-Guided Approach for Evaluating Mesoscale Convective Systems Simulated by the DOE ACME Model

    Feng, Z.; Ma, P. L.; Hardin, J. C.; Houze, R.

    2017-12-01

    Mesoscale convective systems (MCSs) are the largest type of convective storms that develop when convection aggregates and induces mesoscale circulation features. Over North America, MCSs contribute over 60% of the total warm-season precipitation and over half of the extreme daily precipitation in the central U.S. Our recent study (Feng et al. 2016) found that the observed increases in springtime total and extreme rainfall in this region are dominated by increased frequency and intensity of long-lived MCSs*. To date, global climate models typically do not run at a resolution high enough to explicitly simulate individual convective elements and may not have adequate process representations for MCSs, resulting in a large deficiency in projecting changes of the frequency of extreme precipitation events in future climate. In this study, we developed a novel observation-guided approach specifically designed to evaluate simulated MCSs in the Department of Energy's climate model, Accelerated Climate Modeling for Energy (ACME). The ACME model has advanced treatments for convection and subgrid variability and for this study is run at 25 km and 100 km grid spacings. We constructed a robust MCS database consisting of over 500 MCSs from 3 warm-season observations by applying a feature-tracking algorithm to 4-km resolution merged geostationary satellite and 3-D NEXRAD radar network data over the Continental US. This high-resolution MCS database is then down-sampled to the 25 and 100 km ACME grids to re-characterize key MCS properties. The feature-tracking algorithm is adapted with the adjusted characteristics to identify MCSs from ACME model simulations. We demonstrate that this new analysis framework is useful for evaluating ACME's warm-season precipitation statistics associated with MCSs, and provides insights into the model process representations related to extreme precipitation events for future improvement. *Feng, Z., L. R. Leung, S. Hagos, R. A. Houze, C. D. Burleyson

  20. Development and first application of an Aerosol Collection Module (ACM) for quasi online compound specific aerosol measurements

    Hohaus, Thorsten; Kiendler-Scharr, Astrid; Trimborn, Dagmar; Jayne, John; Wahner, Andreas; Worsnop, Doug

    2010-05-01

    Atmospheric aerosols influence climate and human health on regional and global scales (IPCC, 2007). In many environments organics are a major fraction of the aerosol influencing its properties. Due to the huge variety of organic compounds present in atmospheric aerosol current measurement techniques are far from providing a full speciation of organic aerosol (Hallquist et al., 2009). The development of new techniques for compound specific measurements with high time resolution is a timely issue in organic aerosol research. Here we present first laboratory characterisations of an aerosol collection module (ACM) which was developed to allow for the sampling and transfer of atmospheric PM1 aerosol. The system consists of an aerodynamic lens system focussing particles on a beam. This beam is directed to a 3.4 mm in diameter surface which is cooled to -30 °C with liquid nitrogen. After collection the aerosol sample can be evaporated from the surface by heating it to up to 270 °C. The sample is transferred through a 60cm long line with a carrier gas. In order to test the ACM for linearity and sensitivity we combined it with a GC-MS system. The tests were performed with octadecane aerosol. The octadecane mass as measured with the ACM-GC-MS was compared versus the mass as calculated from SMPS derived total volume. The data correlate well (R2 0.99, slope of linear fit 1.1) indicating 100 % collection efficiency. From 150 °C to 270 °C no effect of desorption temperature on transfer efficiency could be observed. The ACM-GC-MS system was proven to be linear over the mass range 2-100 ng and has a detection limit of ~ 2 ng. First experiments applying the ACM-GC-MS system were conducted at the Jülich Aerosol Chamber. Secondary organic aerosol (SOA) was formed from ozonolysis of 600 ppbv of b-pinene. The major oxidation product nopinone was detected in the aerosol and could be shown to decrease from 2 % of the total aerosol to 0.5 % of the aerosol over the 48 hours of

  1. A Prediction of the Damping Properties of Hindered Phenol AO-60/polyacrylate Rubber (AO-60/ACM) Composites through Molecular Dynamics Simulation

    Yang, Da-Wei; Zhao, Xiu-Ying; Zhang, Geng; Li, Qiang-Guo; Wu, Si-Zhu

    2016-05-01

    Molecule dynamics (MD) simulation, a molecular-level method, was applied to predict the damping properties of AO-60/polyacrylate rubber (AO-60/ACM) composites before experimental measures were performed. MD simulation results revealed that two types of hydrogen bond, namely, type A (AO-60) -OH•••O=C- (ACM), type B (AO-60) - OH•••O=C- (AO-60) were formed. Then, the AO-60/ACM composites were fabricated and tested to verify the accuracy of the MD simulation through dynamic mechanical thermal analysis (DMTA). DMTA results showed that the introduction of AO-60 could remarkably improve the damping properties of the composites, including the increase of glass transition temperature (Tg) alongside with the loss factor (tan δ), also indicating the AO-60/ACM(98/100) had the best damping performance amongst the composites which verified by the experimental.

  2. Responses of Mixed-Phase Cloud Condensates and Cloud Radiative Effects to Ice Nucleating Particle Concentrations in NCAR CAM5 and DOE ACME Climate Models

    Liu, X.; Shi, Y.; Wu, M.; Zhang, K.

    2017-12-01

    Mixed-phase clouds frequently observed in the Arctic and mid-latitude storm tracks have the substantial impacts on the surface energy budget, precipitation and climate. In this study, we first implement the two empirical parameterizations (Niemand et al. 2012 and DeMott et al. 2015) of heterogeneous ice nucleation for mixed-phase clouds in the NCAR Community Atmosphere Model Version 5 (CAM5) and DOE Accelerated Climate Model for Energy Version 1 (ACME1). Model simulated ice nucleating particle (INP) concentrations based on Niemand et al. and DeMott et al. are compared with those from the default ice nucleation parameterization based on the classical nucleation theory (CNT) in CAM5 and ACME, and with in situ observations. Significantly higher INP concentrations (by up to a factor of 5) are simulated from Niemand et al. than DeMott et al. and CNT especially over the dust source regions in both CAM5 and ACME. Interestingly the ACME model simulates higher INP concentrations than CAM5, especially in the Polar regions. This is also the case when we nudge the two models' winds and temperature towards the same reanalysis, indicating more efficient transport of aerosols (dust) to the Polar regions in ACME. Next, we examine the responses of model simulated cloud liquid water and ice water contents to different INP concentrations from three ice nucleation parameterizations (Niemand et al., DeMott et al., and CNT) in CAM5 and ACME. Changes in liquid water path (LWP) reach as much as 20% in the Arctic regions in ACME between the three parameterizations while the LWP changes are smaller and limited in the Northern Hemispheric mid-latitudes in CAM5. Finally, the impacts on cloud radiative forcing and dust indirect effects on mixed-phase clouds are quantified with the three ice nucleation parameterizations in CAM5 and ACME.

  3. acme: The Amendable Coal-Fire Modeling Exercise. A C++ Class Library for the Numerical Simulation of Coal-Fires

    Wuttke, Manfred W.

    2017-04-01

    At LIAG, we use numerical models to develop and enhance understanding of coupled transport processes and to predict the dynamics of the system under consideration. Topics include geothermal heat utilization, subrosion processes, and spontaneous underground coal fires. Although the details make it inconvenient if not impossible to apply a single code implementation to all systems, their investigations go along similar paths: They all depend on the solution of coupled transport equations. We thus saw a need for a modular code system with open access for the various communities to maximize the shared synergistic effects. To this purpose we develop the oops! ( open object-oriented parallel solutions) - toolkit, a C++ class library for the numerical solution of mathematical models of coupled thermal, hydraulic and chemical processes. This is used to develop problem-specific libraries like acme( amendable coal-fire modeling exercise), a class library for the numerical simulation of coal-fires and applications like kobra (Kohlebrand, german for coal-fire), a numerical simulation code for standard coal-fire models. Basic principle of the oops!-code system is the provision of data types for the description of space and time dependent data fields, description of terms of partial differential equations (pde), their discretisation and solving methods. Coupling of different processes, described by their particular pde is modeled by an automatic timescale-ordered operator-splitting technique. acme is a derived coal-fire specific application library, depending on oops!. If specific functionalities of general interest are implemented and have been tested they will be assimilated into the main oops!-library. Interfaces to external pre- and post-processing tools are easily implemented. Thus a construction kit which can be arbitrarily amended is formed. With the kobra-application constructed with acme we study the processes and propagation of shallow coal seam fires in particular in

  4. ACM-based automatic liver segmentation from 3-D CT images by combining multiple atlases and improved mean-shift techniques.

    Ji, Hongwei; He, Jiangping; Yang, Xin; Deklerck, Rudi; Cornelis, Jan

    2013-05-01

    In this paper, we present an autocontext model(ACM)-based automatic liver segmentation algorithm, which combines ACM, multiatlases, and mean-shift techniques to segment liver from 3-D CT images. Our algorithm is a learning-based method and can be divided into two stages. At the first stage, i.e., the training stage, ACM is performed to learn a sequence of classifiers in each atlas space (based on each atlas and other aligned atlases). With the use of multiple atlases, multiple sequences of ACM-based classifiers are obtained. At the second stage, i.e., the segmentation stage, the test image will be segmented in each atlas space by applying each sequence of ACM-based classifiers. The final segmentation result will be obtained by fusing segmentation results from all atlas spaces via a multiclassifier fusion technique. Specially, in order to speed up segmentation, given a test image, we first use an improved mean-shift algorithm to perform over-segmentation and then implement the region-based image labeling instead of the original inefficient pixel-based image labeling. The proposed method is evaluated on the datasets of MICCAI 2007 liver segmentation challenge. The experimental results show that the average volume overlap error and the average surface distance achieved by our method are 8.3% and 1.5 m, respectively, which are comparable to the results reported in the existing state-of-the-art work on liver segmentation.

  5. Enabling Chemistry of Gases and Aerosols for Assessment of Short-Lived Climate Forcers: Improving Solar Radiation Modeling in the DOE-ACME and CESM models

    Prather, Michael [Univ. of California, Irvine, CA (United States)

    2018-01-12

    This proposal seeks to maintain the DOE-ACME (offshoot of CESM) as one of the leading CCMs to evaluate near-term climate mitigation. It will implement, test, and optimize the new UCI photolysis codes within CESM CAM5 and new CAM versions in ACME. Fast-J is a high-order-accuracy (8 stream) code for calculating solar scattering and absorption in a single column atmosphere containing clouds, aerosols, and gases that was developed at UCI and implemented in CAM5 under the previous BER/SciDAC grant.

  6. CLIC-ACM: generic modular rad-hard data acquisition system based on CERN GBT versatile link

    Bielawski, B.; Locci, F.; Magnoni, S.

    2015-01-01

    CLIC is a world-wide collaboration to study the next ''terascale'' lepton collider, relying upon a very innovative concept of two-beam-acceleration. This accelerator, currently under study, will be composed of the subsequence of 21000 two-beam-modules. Each module requires more than 300 analogue and digital signals which need to be acquired and controlled in a synchronous way. CLIC-ACM (Acquisition and Control Module) is the 'generic' control and acquisition module developed to accommodate the controls of all these signals for various sub-systems and related specification in term of data bandwidth, triggering and timing synchronization. This paper describes the system architecture with respect to its radiation-tolerance, power consumption and scalability

  7. HPDC ´12 : proceedings of the 21st ACM symposium on high-performance parallel and distributed computing, June 18-22, 2012, Delft, The Netherlands

    Epema, D.H.J.; Kielmann, T.; Ripeanu, M.

    2012-01-01

    Welcome to ACM HPDC 2012! This is the twenty-first year of HPDC and we are pleased to report that our community continues to grow in size, quality and reputation. The program consists of three days packed with presentations on the latest developments in high-performance parallel and distributed

  8. Proceeding of the ACM/IEEE-CS Joint Conference on Digital Libraries (1st, Roanoke, Virginia, June 24-28, 2001).

    Association for Computing Machinery, New York, NY.

    Papers in this Proceedings of the ACM/IEEE-CS Joint Conference on Digital Libraries (Roanoke, Virginia, June 24-28, 2001) discuss: automatic genre analysis; text categorization; automated name authority control; automatic event generation; linked active content; designing e-books for legal research; metadata harvesting; mapping the…

  9. Human factors in computing systems: focus on patient-centered health communication at the ACM SIGCHI conference.

    Wilcox, Lauren; Patel, Rupa; Chen, Yunan; Shachak, Aviv

    2013-12-01

    Health Information Technologies, such as electronic health records (EHR) and secure messaging, have already transformed interactions among patients and clinicians. In addition, technologies supporting asynchronous communication outside of clinical encounters, such as email, SMS, and patient portals, are being increasingly used for follow-up, education, and data reporting. Meanwhile, patients are increasingly adopting personal tools to track various aspects of health status and therapeutic progress, wishing to review these data with clinicians during consultations. These issues have drawn increasing interest from the human-computer interaction (HCI) community, with special focus on critical challenges in patient-centered interactions and design opportunities that can address these challenges. We saw this community presenting and interacting at the ACM SIGCHI 2013, Conference on Human Factors in Computing Systems, (also known as CHI), held April 27-May 2nd, 2013 at the Palais de Congrès de Paris in France. CHI 2013 featured many formal avenues to pursue patient-centered health communication: a well-attended workshop, tracks of original research, and a lively panel discussion. In this report, we highlight these events and the main themes we identified. We hope that it will help bring the health care communication and the HCI communities closer together. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  10. A multicopper oxidase is essential for manganese oxidation and laccase-like activity in Pedomicrobium sp. ACM 3067.

    Ridge, Justin P; Lin, Marianne; Larsen, Eloise I; Fegan, Mark; McEwan, Alastair G; Sly, Lindsay I

    2007-04-01

    Pedomicrobium sp. ACM 3067 is a budding-hyphal bacterium belonging to the alpha-Proteobacteria which is able to oxidize soluble Mn2+ to insoluble manganese oxide. A cosmid, from a whole-genome library, containing the putative genes responsible for manganese oxidation was identified and a primer-walking approach yielded 4350 bp of novel sequence. Analysis of this sequence showed the presence of a predicted three-gene operon, moxCBA. The moxA gene product showed homology to multicopper oxidases (MCOs) and contained the characteristic four copper-binding motifs (A, B, C and D) common to MCOs. An insertion mutation of moxA showed that this gene was essential for both manganese oxidation and laccase-like activity. The moxB gene product showed homology to a family of outer membrane proteins which are essential for Type I secretion in Gram-negative bacteria. moxBA has not been observed in other manganese-oxidizing bacteria but homologues were identified in the genomes of several bacteria including Sinorhizobium meliloti 1021 and Agrobacterium tumefaciens C58. These results suggest that moxBA and its homologues constitute a family of genes encoding an MCO and a predicted component of the Type I secretion system.

  11. Improving simulated long-term responses of vegetation to temperature and precipitation extremes using the ACME land model

    Ricciuto, D. M.; Warren, J.; Guha, A.

    2017-12-01

    While carbon and energy fluxes in current Earth system models generally have reasonable instantaneous responses to extreme temperature and precipitation events, they often do not adequately represent the long-term impacts of these events. For example, simulated net primary productivity (NPP) may decrease during an extreme heat wave or drought, but may recover rapidly to pre-event levels following the conclusion of the extreme event. However, field measurements indicate that long-lasting damage to leaves and other plant components often occur, potentially affecting the carbon and energy balance for months after the extreme event. The duration and frequency of such extreme conditions is likely to shift in the future, and therefore it is critical for Earth system models to better represent these processes for more accurate predictions of future vegetation productivity and land-atmosphere feedbacks. Here we modify the structure of the Accelerated Climate Model for Energy (ACME) land surface model to represent long-term impacts and test the improved model against observations from experiments that applied extreme conditions in growth chambers. Additionally, we test the model against eddy covariance measurements that followed extreme conditions at selected locations in North America, and against satellite-measured vegetation indices following regional extreme events.

  12. ACMS-Data

    Department of Homeland Security — The Records of CBP training activities in the academies and in-service field training. This data is for processing by COTS Application Acadis Readiness Suite and is...

  13. Temperature profiles from mechanical bathythermograph (MBT) casts from the USS ACME in the North Pacific Ocean in support of the Fleet Observations of Oceanographic Data (FLOOD) project from 1968-04-05 to 1968-04-25 (NODC Accession 6800642)

    National Oceanic and Atmospheric Administration, Department of Commerce — MBT data were collected from the USS ACME in support of the Fleet Observations of Oceanographic Data (FLOOD) project. Data were collected by US Navy; Ships of...

  14. Experimental determination of the partitioning coefficient and volatility of important BVOC oxidation products using the Aerosol Collection Module (ACM) coupled to a PTR-ToF-MS

    Gkatzelis, G.; Hohaus, T.; Tillmann, R.; Schmitt, S. H.; Yu, Z.; Schlag, P.; Wegener, R.; Kaminski, M.; Kiendler-Scharr, A.

    2015-12-01

    Atmospheric aerosol can alter the Earth's radiative budget and global climate but can also affect human health. A dominant contributor to the submicrometer particulate matter (PM) is organic aerosol (OA). OA can be either directly emitted through e.g. combustion processes (primary OA) or formed through the oxidation of organic gases (secondary organic aerosol, SOA). A detailed understanding of SOA formation is of importance as it constitutes a major contribution to the total OA. The partitioning between the gas and particle phase as well as the volatility of individual components of SOA is yet poorly understood adding uncertainties and thus complicating climate modelling. In this work, a new experimental methodology was used for compound-specific analysis of organic aerosol. The Aerosol Collection Module (ACM) is a newly developed instrument that deploys an aerodynamic lens to separate the gas and particle phase of an aerosol. The particle phase is directed to a cooled sampling surface. After collection particles are thermally desorbed and transferred to a detector for further analysis. In the present work, the ACM was coupled to a Proton Transfer Reaction-Time of Flight-Mass Spectrometer (PTR-ToF-MS) to detect and quantify organic compounds partitioning between the gas and particle phase. This experimental approach was used in a set of experiments at the atmosphere simulation chamber SAPHIR to investigate SOA formation. Ozone oxidation with subsequent photochemical aging of β-pinene, limonene and real plant emissions from Pinus sylvestris (Scots pine) were studied. Simultaneous measurement of the gas and particle phase using the ACM-PTR-ToF-MS allows to report partitioning coefficients of important BVOC oxidation products. Additionally, volatility trends and changes of the SOA with photochemical aging are investigated and compared for all systems studied.

  15. Design of ET(B) receptor agonists: NMR spectroscopic and conformational studies of ET7-21[Leu7, Aib11, Cys(Acm)15].

    Hewage, Chandralal M; Jiang, Lu; Parkinson, John A; Ramage, Robert; Sadler, Ian H

    2002-03-01

    In a previous report we have shown that the endothelin-B receptor-selective linear endothelin peptide, ET-1[Cys (Acm)1,15, Ala3, Leu7, Aib11], folds into an alpha-helical conformation in a methanol-d3/water co-solvent [Hewage et al. (1998) FEBS Lett., 425, 234-238]. To study the requirements for the structure-activity relationships, truncated analogues of this peptide were subjected to further studies. Here we report the solution conformation of ET7-21[Leu7, Aib11, Cys(Acm)15], in a methanol-d3/water co-solvent at pH 3.6, by NMR spectroscopic and molecular modelling studies. Further truncation of this short peptide results in it displaying poor agonist activity. The modelled structure shows that the peptide folds into an alpha-helical conformation between residues Lys9-His16, whereas the C-terminus prefers no fixed conformation. This truncated linear endothelin analogue is pivotal for designing endothelin-B receptor agonists.

  16. Evidence for heterogeneity of astrocyte de-differentiation in vitro: astrocytes transform into intermediate precursor cells following induction of ACM from scratch-insulted astrocytes.

    Yang, Hao; Qian, Xin-Hong; Cong, Rui; Li, Jing-wen; Yao, Qin; Jiao, Xi-Ying; Ju, Gong; You, Si-Wei

    2010-04-01

    Our previous study definitely demonstrated that the mature astrocytes could undergo a de-differentiation process and further transform into pluripotential neural stem cells (NSCs), which might well arise from the effect of diffusible factors released from scratch-insulted astrocytes. However, these neurospheres passaged from one neurosphere-derived from de-differentiated astrocytes possessed a completely distinct characteristic in the differentiation behavior, namely heterogeneity of differentiation. The heterogeneity in cell differentiation has become a crucial but elusive issue. In this study, we show that purified astrocytes could de-differentiate into intermediate precursor cells (IPCs) with addition of scratch-insulted astrocyte-conditioned medium (ACM) to the culture, which can express NG2 and A2B5, the IPCs markers. Apart from the number of NG2(+) and A2B5(+) cells, the percentage of proliferative cells as labeled with BrdU progressively increased with prolonged culture period ranging from 1 to 10 days. Meanwhile, the protein level of A2B5 in cells also increased significantly. These results revealed that not all astrocytes could de-differentiate fully into NSCs directly when induced by ACM, rather they generated intermediate or more restricted precursor cells that might undergo progressive de-differentiation to generate NSCs.

  17. Analysis of Residual Nuclide in a ACM and ACCT of 100-MeV proton beamline By measurement X-ray Spectrum

    Park, Jeong-Min; Yun, Sang-Pil; Kim, Han-Sung; Kwon, Hyeok-Jung; Cho, Yong-Sub [Korea Atomic Energy Research Institute, Gyeongju (Korea, Republic of)

    2015-10-15

    The proton beam is provides to users as various energy range from 20 MeV to 100 MeV. After protons generated from the ion source are accelerated to 100 MeV and irradiated to target through bending magnet and AC magnet. At this time, relatively high dose X-ray is emitted due to collision of proton and components of beamline. The generated X-ray is remaining after the accelerator is turned off and analyzing residual nuclides through the measurement of X-ray spectrum. Then identify the components that are the primary cause of residual nuclides are detected form the AC magnet(ACM) and associated components (ACCT). Analysis of the X-ray spectrum generated form the AC magnet(ACM) and AC current transformer(ACCT) of 100 MeV beamline according to the proton beam irradiation, most of the residual nuclides are identified it can be seen that emission in the stainless steel by beam loss.

  18. Enterococcus faecium biofilm formation: identification of major autolysin AtlAEfm, associated Acm surface localization, and AtlAEfm-independent extracellular DNA Release.

    Paganelli, Fernanda L; Willems, Rob J L; Jansen, Pamela; Hendrickx, Antoni; Zhang, Xinglin; Bonten, Marc J M; Leavis, Helen L

    2013-04-16

    Enterococcus faecium is an important multidrug-resistant nosocomial pathogen causing biofilm-mediated infections in patients with medical devices. Insight into E. faecium biofilm pathogenesis is pivotal for the development of new strategies to prevent and treat these infections. In several bacteria, a major autolysin is essential for extracellular DNA (eDNA) release in the biofilm matrix, contributing to biofilm attachment and stability. In this study, we identified and functionally characterized the major autolysin of E. faecium E1162 by a bioinformatic genome screen followed by insertional gene disruption of six putative autolysin genes. Insertional inactivation of locus tag EfmE1162_2692 resulted in resistance to lysis, reduced eDNA release, deficient cell attachment, decreased biofilm, decreased cell wall hydrolysis, and significant chaining compared to that of the wild type. Therefore, locus tag EfmE1162_2692 was considered the major autolysin in E. faecium and renamed atlAEfm. In addition, AtlAEfm was implicated in cell surface exposure of Acm, a virulence factor in E. faecium, and thereby facilitates binding to collagen types I and IV. This is a novel feature of enterococcal autolysins not described previously. Furthermore, we identified (and localized) autolysin-independent DNA release in E. faecium that contributes to cell-cell interactions in the atlAEfm mutant and is important for cell separation. In conclusion, AtlAEfm is the major autolysin in E. faecium and contributes to biofilm stability and Acm localization, making AtlAEfm a promising target for treatment of E. faecium biofilm-mediated infections. IMPORTANCE Nosocomial infections caused by Enterococcus faecium have rapidly increased, and treatment options have become more limited. This is due not only to increasing resistance to antibiotics but also to biofilm-associated infections. DNA is released in biofilm matrix via cell lysis, caused by autolysin, and acts as a matrix stabilizer. In this study

  19. 80 A/cm2 electron beams from metal targets irradiated by KrCl and XeCl excimer lasers

    Beloglazov, A.; Martino, M.; Nassisi, V.

    1996-05-01

    Due to the growing demand for high-current and long-duration electron-beam devices, laser electron sources were investigated in our laboratory. Experiments on electron-beam generation and propagation from aluminium and copper targets illuminated by XeCl (308 nm) and KrCl (222 nm) excimer lasers, were carried out under plasma ignition due to laser irradiation. This plasma supplied a spontaneous accelerating electric field of about 370 kV/m without an external accelerating voltage. By applying the modified one-dimensional Poisson equation, we computed the expected current and we also estimated the plasma concentration during the accelerating process. At 40 kV of accelerating voltage, an output current pulse of about 80 A/cm2 was detected from an Al target irradiated by the shorter wavelength laser.

  20. Construction of improved temperature-sensitive and mobilizable vectors and their use for constructing mutations in the adhesin-encoding acm gene of poorly transformable clinical Enterococcus faecium strains.

    Nallapareddy, Sreedhar R; Singh, Kavindra V; Murray, Barbara E

    2006-01-01

    Inactivation by allelic exchange in clinical isolates of the emerging nosocomial pathogen Enterococcus faecium has been hindered by lack of efficient tools, and, in this study, transformation of clinical isolates was found to be particularly problematic. For this reason, a vector for allelic replacement (pTEX5500ts) was constructed that includes (i) the pWV01-based gram-positive repAts replication region, which is known to confer a high degree of temperature intolerance, (ii) Escherichia coli oriR from pUC18, (iii) two extended multiple-cloning sites located upstream and downstream of one of the marker genes for efficient cloning of flanking regions for double-crossover mutagenesis, (iv) transcriptional terminator sites to terminate undesired readthrough, and (v) a synthetic extended promoter region containing the cat gene for allelic exchange and a high-level gentamicin resistance gene, aph(2'')-Id, to distinguish double-crossover recombination, both of which are functional in gram-positive and gram-negative backgrounds. To demonstrate the functionality of this vector, the vector was used to construct an acm (encoding an adhesin to collagen from E. faecium) deletion mutant of a poorly transformable multidrug-resistant E. faecium endocarditis isolate, TX0082. The acm-deleted strain, TX6051 (TX0082Deltaacm), was shown to lack Acm on its surface, which resulted in the abolishment of the collagen adherence phenotype observed in TX0082. A mobilizable derivative (pTEX5501ts) that contains oriT of Tn916 to facilitate conjugative transfer from the transformable E. faecalis strain JH2Sm::Tn916 to E. faecium was also constructed. Using this vector, the acm gene of a nonelectroporable E. faecium wound isolate was successfully interrupted. Thus, pTEX5500ts and its mobilizable derivative demonstrated their roles as important tools by helping to create the first reported allelic replacement in E. faecium; the constructed this acm deletion mutant will be useful for assessing the

  1. From the Padua Muscle Days, the Basic and Applied Myology and the European Journal of Translational Myology to the A&CM Carraro Foundation for Translational Myology

    Ugo Carraro

    2017-09-01

    Full Text Available As a young researched I had the option to work on skeletal muscle at the University of Padova, Italy. Introduced to the study of muscle denervation/reinnervation, I started a project on long term denervated muscle that still is my primary interest and took me from rodents’ models of chronic muscle denervation to human spinal cord injury-related muscle denervation and its managements. On the way, I organized a series of conferences in Euganei Hills, Padua, Italy and an international journal, the Basic and Applied Myology. From 2010 this journal changed name to European Journal of Translational Myology, whose contents are focused on Myology, though they have important implications in aging, several neurological disorders and cancer cachexia. A relatively large community of Basic Biologists, Clinicians and Biomedical Technologists (usually meeting separately in very different specialty Conferences recognized the need of a Meeting Series focused on Translational Myology. Thus the Padua Muscle Days (PMD started more than 25 years ago. The next events of the PMD Series will be in Autumn 2017 an one-day Seminar on Easy Aging and a three-day event: The 2017 Fall Padua Experts’ Meeting. During the 2018Spring PMD, the Giovanni Salviati Memorial will be organized to honor a beloved friend and excellent scientist, who abruptly disappeared twenty years ago at the peak of his research activities. Many friends and still-active pupils accepted invitation and will provide the backbone of the Program of the 2018Spring PaduaMuscleDay to be held, March 14-16, 2018 in Euganei Hills and Padua (Italy. All these events will be sponsored by the Interdepartmental Research Centre of Myology of the University of Padova and by the A&CM Carraro Foundation for Translational Myology.

  2. Fabrication of 93.7 m long PLD-EuBCO + BaHfO_3 coated conductors with 103 A/cm W at 77 K under 3 T

    Yoshida, T.; Ibi, A.; Takahashi, T.; Yoshizumi, M.; Izumi, T.; Shiohara, Y.

    2015-01-01

    Highlights: • A 93.7 m long EuBCO + BHO CC with 103 A/cm W at 77 K under 3 T was obtained. • The 93.7 m long CC showed high I_c values and high n-values with high uniformity. • The average I_c value at 77 K under 3 T was estimated by that at 77 K under 0.3 T. - Abstract: Introduction of artificial pinning centers such as BaHfO_3 (BHO), BaZrO_3 (BZO) and BaSnO_3 (BSO) into REBa_2Cu_3O_7_−_δ (REBCO) coated conductor (CC) layers could improve the in-field critical currents (I_c) in wide ranges of temperatures and magnetic fields. In particular, a combination of EuBCO + BHO has been found to be effective for attaining high in-field I_c performance by means of IBAD/PLD process in short length samples. In this work, we have successfully fabricated a 93.7 m long EuBCO + BHO CC with 103 A/cm W at 77 K under a magnet field (B) of 3 T applied perpendicular to the CC (B//c). The 93.7 m long EuBCO + BHO CC had high uniformity of I_c values and n-values without any trend of fluctuations, independent of the external field up to 0.3 T. I_c–B–applied angle (θ) profiles of the 93.7 m long EuBCO + BHO CC sample showed the high in-field I_c values in all directions of applied magnetic fields especially B//c (at θ ∼ 180°, I_c = 157 A/cm W) at 77 K under 3 T. The profiles were about the same as those in a short length sample.

  3. Immature osteoblastic MG63 cells possess two calcitonin gene-related peptide receptor subtypes that respond differently to [Cys(Acm)(2,7)] calcitonin gene-related peptide and CGRP(8-37).

    Kawase, Tomoyuki; Okuda, Kazuhiro; Burns, Douglas M

    2005-10-01

    Calcitonin gene-related peptide (CGRP) is clearly an anabolic factor in skeletal tissue, but the distribution of CGRP receptor (CGRPR) subtypes in osteoblastic cells is poorly understood. We previously demonstrated that the CGRPR expressed in osteoblastic MG63 cells does not match exactly the known characteristics of the classic subtype 1 receptor (CGRPR1). The aim of the present study was to further characterize the MG63 CGRPR using a selective agonist of the putative CGRPR2, [Cys(Acm)(2,7)]CGRP, and a relatively specific antagonist of CGRPR1, CGRP(8-37). [Cys(Acm)(2,7)]CGRP acted as a significant agonist only upon ERK dephosphorylation, whereas this analog effectively antagonized CGRP-induced cAMP production and phosphorylation of cAMP response element-binding protein (CREB) and p38 MAPK. Although it had no agonistic action when used alone, CGRP(8-37) potently blocked CGRP actions on cAMP, CREB, and p38 MAPK but had less of an effect on ERK. Schild plot analysis of the latter data revealed that the apparent pA2 value for ERK is clearly distinguishable from those of the other three plots as judged using the 95% confidence intervals. Additional assays using 3-isobutyl-1-methylxanthine or the PKA inhibitor N-(2-[p-bromocinnamylamino]ethyl)-5-isoquinolinesulfonamide hydrochloride (H-89) indicated that the cAMP-dependent pathway was predominantly responsible for CREB phosphorylation, partially involved in ERK dephosphorylation, and not involved in p38 MAPK phosphorylation. Considering previous data from Scatchard analysis of [125I]CGRP binding in connection with these results, these findings suggest that MG63 cells possess two functionally distinct CGRPR subtypes that show almost identical affinity for CGRP but different sensitivity to CGRP analogs: one is best characterized as a variation of CGRPR1, and the second may be a novel variant of CGRPR2.

  4. The Acme of Skill: Nonkinetic Warfare

    Teo, Cheng H

    2008-01-01

    ... impairment of the enemy's will to fight. Four global trends identified in this paper -- economic prosperity, freedom of information, the rise of nationalism, and globalization and interdependence -- are possible causes for this shift...

  5. Proposed Expansion of Acme Landfill Operations.

    1982-08-01

    hazardous waste ponds that use solar evaporation processes to dispose of liquid hazardous wastes have an indefinite life, the quantity of liquid that may...determined at a later date. The use of solar evaporation ponds, for example, would preclude the use of spreading and compaction equipment used for...pesticides in spray cans, residual chemical solvents in steel drums, herbicide residues on grass clippings, or organic wastes in disposable baby diapers , a

  6. The ACM Periodical Bank: A Retrospective View.

    Clarke, Jack A.

    1980-01-01

    Evaluates a cooperative venture in interlibrary lending of periodicals planned and executed by ten midwestern colleges. The study traces the consortium's history from 1967 to the present, describing successes and problems. (RAA)

  7. The Acme of Skill: Nonkinetic Warfare

    2008-05-01

    results are mixed. For the im- mense cost that often accompanies war, the returns of war are not guaranteed. On nonkinetic operations, it may appear that...ing, together with other kinetic capabilities such as emphasizing irregular operations, increasing ground troop levels, and recruiting foreign

  8. The National Shipbuilding Research Program, 1990 Ship Production Symposium, Paper No. 4B-3: The Development of CO2 Blasting Technology in Naval Shipyards

    Fuller, Jimmy W

    1990-01-01

    .... TEXT Navy ships bottoms are painted with antifouling paints that Contain pesticide ingredients that are used to control attachment and growth of marine animals and plants living in association...

  9. Adaptive ACMS: A robust localized Approximated Component Mode Synthesis Method

    Madureira, Alexandre L.; Sarkis, Marcus

    2017-01-01

    We consider finite element methods of multiscale type to approximate solutions for two-dimensional symmetric elliptic partial differential equations with heterogeneous $L^\\infty$ coefficients. The methods are of Galerkin type and follows the Variational Multiscale and Localized Orthogonal Decomposition--LOD approaches in the sense that it decouples spaces into multiscale and fine subspaces. In a first method, the multiscale basis functions are obtained by mapping coarse basis functions, based...

  10. Surgical management of an ACM aneurysm eight years after coiling.

    Pogády, P; Fellner, F; Trenkler, J; Wurm, G

    2007-04-01

    The authors present a case report on rebleeding of a medial cerebral aneurysm (MCA) eight years after complete endovascular coiling. The primarily successfully coiled MCA aneurysm showed a local regrowth which, however, was not the source of the rebleeding. The angiogram demonstrated no evidence of contrast filling of the coiled segment, but according to intraoperative findings (haematoma location, displacement of coils, evident place of rupture) there is no doubt that the coiled segment of the aneurysm was responsible for the haemorrhage.

  11. Iaverage current mode (ACM) control for switching power converters

    2014-01-01

    Providing a fast current sensor direct feedback path to a modulator for controlling switching of a switched power converter in addition to an integrating feedback path which monitors average current for control of a modulator provides fast dynamic response consistent with system stability and average current mode control. Feedback of output voltage for voltage regulation can be combined with current information in the integrating feedback path to limit bandwidth of the voltage feedback signal.

  12. ARM Airborne Carbon Measurements (ARM-ACME) and ARM-ACME 2.5 Final Campaign Reports

    Biraud, S. C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Tom, M. S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sweeney, C. [NOAA Earth Systems Research Lab., Boulder, CO (United States)

    2016-01-01

    We report on a 5-year multi-institution and multi-agency airborne study of atmospheric composition and carbon cycling at the Atmospheric Radiation Measurement (ARM) Climate Research Facility’s Southern Great Plains (SGP) site, with scientific objectives that are central to the carbon-cycle and radiative-forcing goals of the U.S. Global Change Research Program and the North American Carbon Program (NACP). The goal of these measurements is to improve understanding of 1) the carbon exchange of the Atmospheric Radiation Measurement (ARM) SGP region; 2) how CO2 and associated water and energy fluxes influence radiative-forcing, convective processes, and CO2 concentrations over the ARM SGP region, and 3) how greenhouse gases are transported on continental scales.

  13. Multilingual Information Discovery and AccesS (MIDAS): A Joint ACM DL'99/ ACM SIGIR'99 Workshop.

    Oard, Douglas; Peters, Carol; Ruiz, Miguel; Frederking, Robert; Klavans, Judith; Sheridan, Paraic

    1999-01-01

    Discusses a multidisciplinary workshop that addressed issues concerning internationally distributed information networks. Highlights include multilingual information access in media other than character-coded text; cross-language information retrieval and multilingual metadata; and evaluation of multilingual systems. (LRW)

  14. USL NASA/RECON project presentations at the 1985 ACM Computer Science Conference: Abstracts and visuals

    Dominick, Wayne D. (Editor); Chum, Frank Y.; Gallagher, Suzy; Granier, Martin; Hall, Philip P.; Moreau, Dennis R.; Triantafyllopoulos, Spiros

    1985-01-01

    This Working Paper Series entry represents the abstracts and visuals associated with presentations delivered by six USL NASA/RECON research team members at the above named conference. The presentations highlight various aspects of NASA contract activities pursued by the participants as they relate to individual research projects. The titles of the six presentations are as follows: (1) The Specification and Design of a Distributed Workstation; (2) An Innovative, Multidisciplinary Educational Program in Interactive Information Storage and Retrieval; (3) Critical Comparative Analysis of the Major Commercial IS and R Systems; (4) Design Criteria for a PC-Based Common User Interface to Remote Information Systems; (5) The Design of an Object-Oriented Graphics Interface; and (6) Knowledge-Based Information Retrieval: Techniques and Applications.

  15. Multimedia and security: Workshop at ACM Multimedia '98, Bristol, U.K., September 12 - 13, 1998

    Dittmann, J.; Wohlmacher, P.; Horster, P.; Steinmetz, R.

    1998-01-01

    In this paper we describe the most important security requirements, which must be fulfilled by today's IT-systems, and the security measures used to satisfy these requirements. These security measures are based on modern cryptographic mechanisms as well as on security infrastructures. Regarding data security and communication security in particular in the field of multimedia, the requirements on security increase. If and in which way the discussed security mechanisms can be applied to multime...

  16. PLDI 2006. Proceedings of the 2006 ACM SIGPLAN Conferenceon Programming Language Design and Implementation

    for that paper. The champion summarized the paper's contribution as well as the pros and cons of the paper. The discussion then was opened up to the other reviewers of the paper and to general questions from the rest of the PC. Paper scores were not returned to the authors with the reviews. We accepted 36 papers...

  17. Proposed Expansion of Acme Landfill Operations, Contra Costa, County, California. Volume 1.

    1983-06-01

    have to be determined at a later date. The use of solar evaporation ponds, for example, would preclude the use of spreading and compaction equipment...organic wastes in disposable baby diapers , a significant portion of the contaminants come from the refuse itself. Apart from the obvious constituents...hazard is increased by atmospheric humidity, slope steepness, vegetation type, exposure to solar radiation, wind speed and direction, accessibility

  18. ACM SIGGRAPH Video Review Issue 152, SIGGRAPH 2005 Animation Theater Program PART 2

    2005-01-01

    to accurately understand the anatomicaldetails, real-time convergence could not be achieved by existingCPU implementations. Dedicated software was developed and runon a 3 GHz Pentium 4 PC with an NVIDIA Geforce 6800 Ultra graphicscard.Funding by the Danish Research Agency and the Centre for...

  19. Proceedings of the 22nd ACM conference on Hypertext and hypermedia

    and Ubiquitous Hypermedia, chaired by Niels Olof Bouvin and Frank Shipman; Social Media (Linking People and Things), chaired by Andreas Hotho, Gerd Stumme and Markus Strohmaier; Interaction, Narrative, and Storytelling, chaired by Mark Bernstein and Frank Nack. Three keynote speakers represent the breadth, depth....... Noshir Contractor investigates factors that lead to the formation, maintenance and dissolution of dynamically linked social and knowledge networks. The Program Committee and the reviewers worked hard to select an excellent program from 104 paper submissions. We accepted 31 full papers and 4 short papers...

  20. HYPERTEXT 98. The Proceedings of the Ninth ACM Conference on Hypertext and Hypermedia

    The Conference on Hypertext and Hypermedia brings together scholars, researchers, and practitioners from diverse disciplines to consider the form, role and impact of hypertext and hypermedia in a forum of discussion of ideas, design and use of hypertext and hypermedia in a variety of domains. The...

  1. Career Patterns, Employment and Earnings of Graduates of 11 ACM Colleges.

    Wishart, Patricia; Rossmann, Jack

    A study was conducted of 11 private liberal arts colleges, all members of the Associated Colleges of the Midwest, to relate the career experiences of four graduating classes to their college experiences. The study was conducted as part of the National Project 1, Better Information for Student Choice, supported by the Fund for the Improvement of…

  2. Assessing the aerosol direct and first indirect effects using ACM/GCM simulation results

    Huang, H.; Gu, Y.; Xue, Y.; Lu, C. H.

    2016-12-01

    Atmospheric aerosols have been found to play an important role in global climate change but there are still large uncertainty in evaluating its role in the climate system. The aerosols generally affect global and regional climate through the scattering and the absorption of solar radiation (direct effect) and through their influences on cloud particle, number and sizes (first indirect effect). The indirect effect will further affects cloud water content, cloud top albedo and surface precipitations. In this study, we investigate the global climatic effect of aerosols using a coupled NCEP Global Forecast System (GFS) and a land surface model (SSiB2) The OPAC (Optical Properties of Aerosols and Clouds) database is used for aerosol effect. The OPAC data provides the optical properties (i.e., the extinction, scattering and absorption coefficient, single-scattering albedo, asymmetry factor and phase function) of ten types of aerosols under various relative humidity conditions for investigating the global direct and first indirect effects of dust aerosols. For indirect forcings due to liquid water, we follow the approach presented by Jiang et al (2011), in which a parameterization of cloud effective radius was calculated to describe its variance with convective strength and aerosol concentration. Since the oceans also play an important role on aerosol climatic effect, we also design a set of simulations using a coupled atmosphere/ocean model (CFS) to evaluate the sensitivity of aerosol effect with two-way atmosphere-ocean interactions.

  3. Gradient-based reliability maps for ACM-based segmentation of hippocampus.

    Zarpalas, Dimitrios; Gkontra, Polyxeni; Daras, Petros; Maglaveras, Nicos

    2014-04-01

    Automatic segmentation of deep brain structures, such as the hippocampus (HC), in MR images has attracted considerable scientific attention due to the widespread use of MRI and to the principal role of some structures in various mental disorders. In this literature, there exists a substantial amount of work relying on deformable models incorporating prior knowledge about structures' anatomy and shape information. However, shape priors capture global shape characteristics and thus fail to model boundaries of varying properties; HC boundaries present rich, poor, and missing gradient regions. On top of that, shape prior knowledge is blended with image information in the evolution process, through global weighting of the two terms, again neglecting the spatially varying boundary properties, causing segmentation faults. An innovative method is hereby presented that aims to achieve highly accurate HC segmentation in MR images, based on the modeling of boundary properties at each anatomical location and the inclusion of appropriate image information for each of those, within an active contour model framework. Hence, blending of image information and prior knowledge is based on a local weighting map, which mixes gradient information, regional and whole brain statistical information with a multi-atlas-based spatial distribution map of the structure's labels. Experimental results on three different datasets demonstrate the efficacy and accuracy of the proposed method.

  4. Multi-walled carbon nanotubes/polymer composites in absence and presence of acrylic elastomer (ACM).

    Kumar, S; Rath, T; Mahaling, R N; Mukherjee, M; Khatua, B B; Das, C K

    2009-05-01

    Polyetherimide/Multiwall carbon nanotube (MWNTs) nanocomposites containing as-received and modified (COOH-MWNT) carbon nanotubes were prepared through melt process in extruder and then compression molded. Thermal properties of the composites were characterized by thermo-gravimetric analysis (TGA). Field emission scanning electron microscopy (FESEM) images showed that the MWNTs were well dispersed and formed an intimate contact with the polymer matrix without any agglomeration. However the incorporation of modified carbon nanotubes formed fascinating, highly crosslinked, and compact network structure throughout the polymer matrix. This showed the increased adhesion of PEI with modified MWNTs. Scanning electron microscopy (SEM) also showed high degree of dispersion of modified MWNTs along with broken ends. Dynamic mechanical analysis (DMA) results showed a marginal increase in storage modulus (E') and glass transition temperature (T(g)) with the addition of MWNTs. Increase in tensile strength and impact strength of composites confirmed the use the MWNTs as possible reinforcement agent. Both thermal and electrical conductivity of composites increased, but effect is more pronounced on modification due to formation of network of carbon nanotubes. Addition of acrylic elastomer to developed PEI/MWNTs (modified) nanocomposites resulted in the further increase in thermal and electrical properties due to the formation of additional bond between MWNTs and acrylic elastomers at the interface. All the results presented are well corroborated by SEM and FESEM studies.

  5. 1973 Winter Simulation Conference. Sponsored by ACM/AIIE/SHARE/SCi/TIMS.

    Hoggatt, Austin Curwood, Ed.

    A record of the current state of the art of simulation and the major part it now plays in policy formation in large organizations is provided by these conference proceedings. The 40 papers presented reveal an emphasis on the applications of simulation. In addition, the abstracts of 28 papers submitted to a more informal "paper fair" are also…

  6. Accelerated Climate Modeling for Energy (ACME) Final Scientific/Technical Report

    Chaudhary, Aashish [Kitware, Inc.

    2017-10-17

    Seven Department of Energy (DOE) national laboratories, Universities, and Kitware, undertook a coordinated effort to build an Earth system modeling capability tailored to meet the climate change research strategic objectives of the DOE Office of Science, as well as the broader climate change application needs of other DOE programs.

  7. SSCS'10 : Proceedings of the 2010 ACM Workshop on Searching Spontaneous Conversational Speech

    Larson, Martha; Ordelman, Roeland; Metze, Florian; Kraaij, Wessel; de Jong, Franciska

    2010-01-01

    The spoken word is a valuable source of semantic information. Techniques that exploit the spoken word by making use of speech recognition or spoken audio analysis hold clear potential for improving multimedia search. Nonetheless, speech technology remains underexploited by systems that provide

  8. Call for participation first ACM workshop on education in computer security

    Irvine, Cynthia; Orman, Hilarie

    1997-01-01

    Taken from the NPS website. The security of information systems and networks is a growing concern. Experts are needed to design and organize the protection mechanisms for these systems. Both government and industry increasingly seek individuals with knowledge and skills in computer security. In the past, most traditional computer science curricula bypassed formal studies in computer security altogether. An understanding of computer security was achieved largely through on-the-job ...

  9. AcmA of Lactococcus lactis, a cell-binding major autolysin

    Buist, Girbe

    1997-01-01

    onsidering the amount of daily consumed foods which are produced by means of fermentation, such as breads, wines, beers, cheeses, fermented vegetables/fruits and sausages, the economical importance of these biotechnological processes can be hardly overestimated. Lactic acid bacteria (LAB) play an

  10. A new monoclonal antibody for the radio immune diagnosis of colorectal cancer; Nuevo ACM para el radioinmunodiagnostico de cancer colorrectal

    Ramos, M [Centro de Inmunologia Molecular, La Habana (Cuba); and others

    1998-12-31

    Colorectal cancer is the third cause of death among malignant neoplasms in Cuba. Different labeled monoclonal antibodies have been used for the diagnosis and follow-up of this tumors bu immunoscintigraphy. Recently, a new MAB ior c5 have been developed at Center of Molecular Immunology, Havana, Cuba. It recognizes a new tumors associated antigen: IOR C2, found in most of colorectal adenocarcinomas. The aim of the present work was to assess the diagnostic utility of this antibody, Labelled with 99m Tc, as well as to study its pharmacokinetics, biodistribution and internal dosimetry

  11. Proceedings of the 15th IEEE/ACM Symposium on Embedded Systems for Real-Time Multimedia

    Stuijk, S.; Kumar, A.

    2017-01-01

    Multimedia and camera-based technologies play an important role in our daily life, and have become among the most relevant technological innovations. These technologies have proliferated into a wide range of application domains like Internet-of-Things (IoT), Cyber-Physical Systems (CPS), Healthcare

  12. Three-dimensional neural differentiation of embryonic stem cells with ACM induction in microfibrous matrices in bioreactors.

    Liu, Ning; Ouyang, Anli; Li, Yan; Yang, Shang-Tian

    2013-01-01

    The clinical use of pluripotent stem cell (PSC)-derived neural cells requires an efficient differentiation process for mass production in a bioreactor. Toward this goal, neural differentiation of murine embryonic stem cells (ESCs) in three-dimensional (3D) polyethylene terephthalate microfibrous matrices was investigated in this study. To streamline the process and provide a platform for process integration, the neural differentiation of ESCs was induced with astrocyte-conditioned medium without the formation of embryoid bodies, starting from undifferentiated ESC aggregates expanded in a suspension bioreactor. The 3D neural differentiation was able to generate a complex neural network in the matrices. When compared to 2D differentiation, 3D differentiation in microfibrous matrices resulted in a higher percentage of nestin-positive cells (68% vs. 54%) and upregulated gene expressions of nestin, Nurr1, and tyrosine hydroxylase. High purity of neural differentiation in 3D microfibrous matrix was also demonstrated in a spinner bioreactor with 74% nestin + cells. This study demonstrated the feasibility of a scalable process based on 3D differentiation in microfibrous matrices for the production of ESC-derived neural cells. © 2013 American Institute of Chemical Engineers.

  13. Ambulatory circadian monitoring (ACM) based on thermometry, motor activity and body position (TAP): a comparison with polysomnography.

    Ortiz-Tudela, Elisabet; Martinez-Nicolas, Antonio; Albares, Javier; Segarra, Francesc; Campos, Manuel; Estivill, Eduard; Rol, Maria Angeles; Madrid, Juan Antonio

    2014-03-14

    An integrated variable based on the combination of wrist Temperature, motor Activity and body Position (TAP) was previously developed at our laboratory to evaluate the functioning of the circadian system and sleep-wake rhythm under ambulatory conditions. However, the reliability of TAP needed to be validated with polysomnography (PSG). 22 subjects suffering from sleep disorders were monitored for one night with a temperature sensor (iButton), an actimeter (HOBO) and exploratory PSG. Mean waveforms, sensitivity (SE), specificity (SP), agreement rates (AR) and comparisons between TAP and sleep stages were studied. The TAP variable was optimized for SE, SP and AR with respect to each individual variable (SE: 92%; SP: 78%; AR: 86%). These results improved upon estimates previously published for actigraphy. Furthermore, TAP values tended to decrease as sleep depth increased, reaching the lowest point at phase 3. Finally, TAP estimates for sleep latency (SL: 37±9 min), total sleep time (TST: 367±13 min), sleep efficiency (SE: 86.8±1.9%) and number of awakenings (NA>5 min: 3.3±.4) were not significantly different from those obtained with PSG (SL: 29±4 min; SE: 89.9±1.8%; NA>5 min: 2.3±.4), despite the heterogeneity of the sleep pathologies monitored. The TAP variable is a novel measurement for evaluating circadian system status and sleep-wake rhythms with a level of reliability better to that of actigraphy. Furthermore, it allows the evaluation of a patient's sleep-wake rhythm in his/her normal home environment, and at a much lower cost than PSG. Future studies in specific pathologies would verify the relevance of TAP in those conditions. Copyright © 2014 Elsevier Inc. All rights reserved.

  14. Detection of mitotic nuclei in breast histopathology images using localized ACM and Random Kitchen Sink based classifier.

    Beevi, K Sabeena; Nair, Madhu S; Bindu, G R

    2016-08-01

    The exact measure of mitotic nuclei is a crucial parameter in breast cancer grading and prognosis. This can be achieved by improving the mitotic detection accuracy by careful design of segmentation and classification techniques. In this paper, segmentation of nuclei from breast histopathology images are carried out by Localized Active Contour Model (LACM) utilizing bio-inspired optimization techniques in the detection stage, in order to handle diffused intensities present along object boundaries. Further, the application of a new optimal machine learning algorithm capable of classifying strong non-linear data such as Random Kitchen Sink (RKS), shows improved classification performance. The proposed method has been tested on Mitosis detection in breast cancer histological images (MITOS) dataset provided for MITOS-ATYPIA CONTEST 2014. The proposed framework achieved 95% recall, 98% precision and 96% F-score.

  15. Autologous Collagen Matrix (ACM): Lower Pole Support With a Supero-Anterior Capsular Flap in Secondary Subpectoral Breast Augmentation.

    Montemurro, Paolo; Cheema, Mubashir; Hedén, Per; Avvedimento, Stefano; Agko, Mouchammed; Quattrini Li, Alessandro

    2017-05-01

    Secondary aesthetic breast surgery is a complex and challenging scenario. It requires the surgeon to identify contributing factors, provide patient education, make a further management plan, and optimize the conditions for a favorable result. Various techniques have been described in literature but the rate of reoperation is still high. The first author has been using a supero-anterior capsular flap with a neopectoral subcapsular pocket and an implant change in these cases. To review the patient characteristics, indications, and early results of using part of the existing implant capsule for secondary subpectoral breast augmentations. All patients who underwent secondary breast augmentation, over a period of 2 years by the first author (P.M.), using the supero-anterior capsular flap technique were included. The technique involves dissection of a new subpectoral pocket and uses the existing implant capsule as an internal brassiere. A total of 36 patients were operated by this technique. Of these, 17 patients had developed a complication while 19 patients wanted a change in size only. At a mean follow up of 10.2 months, there was no bottoming out, double bubble, or capsular contracture. This reliable technique provides stable results as shown by low rate of complications with the existing follow up. © 2017 The American Society for Aesthetic Plastic Surgery, Inc. Reprints and permission: journals.permissions@oup.com

  16. ARM-ACME V: ARM Airborne Carbon Measurements V on the North Slope of Alaska Science and Implementation Plan

    Biraud, S [Lawrence Berkeley National Laboratory

    2015-05-01

    Atmospheric temperatures are warming faster in the Arctic than predicted by climate models. The impact of this warming on permafrost degradation is not well understood, but it is projected to increase carbon decomposition and greenhouse gas production (CO₂ and/or CH₄) by arctic ecosystems. Airborne observations of atmospheric trace gases, aerosols, and cloud properties at the North Slope of Alaska are improving our understanding of global climate, with the goal of reducing the uncertainty in global and regional climate simulations and projections.

  17. ARM-ACME V: ARM Airborne Carbon Measurements V on the North Slope of Alaska Field Campaign Report

    Biraud, Sebastien C [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2016-05-01

    Atmospheric temperatures are warming faster in the Arctic than predicted by climate models. The impact of this warming on permafrost degradation is not well understood, but it is projected to increase carbon decomposition and greenhouse gas production (CO2 and/or CH4) by arctic ecosystems. Airborne observations of atmospheric trace gases, aerosols and cloud properties in North Slopes of Alaska (NSA) are improving our understanding of global climate, with the goal of reducing the uncertainty in global and regional climate simulations and projections. From June 1 through September 15, 2015, AAF deployed the G1 research aircraft and flew over the North Slope of Alaska (38 flights, 140 science flight hours), with occasional vertical profiling over Prudhoe Bay, Oliktok point, Barrow, Atqasuk, Ivotuk, and Toolik Lake. The aircraft payload included Picarro and Los Gatos Research (LGR) analyzers for continuous measurements of CO2, CH4, H2O, and CO and N2O mixing ratios, and a 12-flask sampler for analysis of carbon cycle gases (CO2, CO, CH4, N2O, 13CO2, and trace hydrocarbon species). The aircraft payload also include measurements of aerosol properties (number size distribution, total number concentration, absorption, and scattering), cloud properties (droplet and ice size information), atmospheric thermodynamic state, and solar/infrared radiation.

  18. Electronic countermeasures (ECM) and acoustic countermeasures (ACM) supported protection for merchant ships against SSM/ASM missiles and mines

    Wallander, Bo L.

    1989-01-01

    Approved for public release; distribution unlimited The necessity for merchant ship self protection has become more and more obvious during recent years. This thesis will investigate the threat (missiles and mines) and associated counter-measures that might be installed to provide a reasonable degree of protection. The results indicate that it is possible to get protection against a sea-skimming missile with a combination of ECM and ESM deployed aboard the ship. For protection against the ...

  19. WIDM'12 : the proceedings of the twelfth ACM international workshop on Web information and data management, November 2, 2012, Maui, Hawaii, USA

    Fletcher, G.H.L.; Mitra, P.

    2012-01-01

    We give an overview of WIDM 2012, held in conjunction with CIKM2012 inMaui, Hawaii. WIDM 2012 is the twelfth in a series of international workshops on Web Information and Data Management held in conjunction with CIKM since 1998. The objective of the workshop is to bring together researchers and

  20. 15th ACM/IEEE-CS Joint Conference on Digital Libraries: Large, Dynamic and Ubiquitous - The Era of the Digital Library

    2015-01-01

    Big Data is everywhere – from Computational Science to Digital Humanities, from Web Analytics to traditional libraries. While there do exist significant challenges in other areas, for many the biggest issue of all is a digital libraries one – How do we preserve big data collections? How do we provide access to big data collections? What new questions can we pose against our big data collections? These are all digital libraries questions. How can we, the digital libraries community, stand up in the face of these challenges and inform collection builders, curators, and interface developers how to best solve their challenges? What assumptions have we been working under that no longer hold in light of Big Data? These are some of the timely questions we hope to address at JCDL 2015.

  1. 40 CFR Appendix A to Subpart M of... - Interpretive Rule Governing Roof Removal Operations

    2010-07-01

    ...-containing material (ACM) is material containing more than one percent asbestos as determined using the... NESHAP classifies ACM as either “friable” or “nonfriable”. Friable ACM is ACM that, when dry, can be crumbled, pulverized or reduced to powder by hand pressure. Nonfriable ACM is ACM that, when dry, cannot be...

  2. Lytr, a phage-derived amidase is most effective in induced lysis of Lactococcus lactis compared with other lactococcal amidases and glucosaminidases

    Steen, Anton; van Schalkwijk, Saskia; Buist, Girbe; Twigt, Marja; Szeliga, Monika; Meijer, Wilco; Kuipers, Oscar P.; Kok, Jan; Hugenholtz, Jeroen

    In the genome of Lactococcus lactis IL1403 five genes encoding peptidoglycan hydrolases are present: four glucosaminidases (acmA, acmB, acmC and acmD) and an endopeptidase (yjgB). Genes for six prophage lysins have also been identified. The genes acmB, acmC, acmD, yjgB and the lysin lytR of prophage

  3. 78 FR 15014 - Change in Bank Control Notices; Acquisitions of Shares of a Bank or Bank Holding Company

    2013-03-08

    ... Meyer, Jr., individually and as trustee of the: ACM, Jr. 2010 3Y GRAT A, the ACM, Jr. 2010 3Y GRAT B, the ACM, Jr. 2010 3Y GRAT C, the ACM, Jr. 2013 2Y GRAT A, the ACM, Jr. 2013 2Y GRAT B, the ACM, Jr. 2013 2Y GRAT C, the ACM, Jr. 2013 2Y GRAT D, the Katharine Clara Kimmel Non- Exempt Trust C/U Elisabeth...

  4. 77 FR 15145 - Ares Capital Corporation et al.;

    2012-03-14

    ... Capital Corporation (the ``Company''), Ares Capital Management LLC (``ACM'') and Ivy Hill Asset Management...''). The Board has delegated daily management and investment authority to ACM pursuant to an investment advisory and management agreement between ACM and the [[Page 15146

  5. Report on the "Secure Vehicular Communications: Results and Challenges Ahead" Workshop

    Papadimitratos, Panos; Hubaux, Jean-Pierre

    2008-01-01

    © ACM, (2008). This is the author’s version of the work. It is posted here by permission of ACM for your personaluse. Not for redistribution. The definitive version was published in ACM SIGMOBILE Mobile Computing and Communications Review . http://doi.acm.org/10.114510/1394555.1394567 .QC 20110712

  6. 77 FR 30005 - Office of the Assistant Secretary for Health, Statement of Organization, Functions, and...

    2012-05-21

    .... Specifically, it realigns these functions in the Office of the Surgeon General (ACM) and abolishes the Office... Section AC.20, Functions, delete Paragraph ``I. Office of Surgeon General (ACM),'' in its entirety and replace with the following: I. Office of the Surgeon General (ACM) Section ACM.00 Mission: The Office of...

  7. Exposure characteristics of positive tone electron beam resist containing p-chloro-α-methylstyrene

    Ochiai, Shunsuke; Takayama, Tomohiro; Kishimura, Yukiko; Asada, Hironori; Sonoda, Manae; Iwakuma, Minako; Hoshino, Ryoichi

    2017-07-01

    The positive tone resist consisted of methyl-α-chloroacrylate (ACM) and α-methylstyrene (MS) has higher sensitivity and higher dry etching resistance than poly (methylmethacrylate) (PMMA) due to the presence of a chlorine atom and a phenyl group. Copolymers consisted of ACM and p-chloro-α-methylstyrene (PCMS), where the additional chlorine atom is introduced in phenyl group compared with ACM-MS resist are synthesized and their exposure characteristics are investigated. ACM-PCMS resist with the ACM:PCMS composition ratio of 49:51 indicates the high solubility for amyl acetate developer. As the ACM composition ratio increases, the solubility of ACM-PCMS resist is suppressed. In both ACM-PCMS and ACM-MS resists, the sensitivity decreases while the contrast increases with increasing ACM ratio. When the composition ratio of ACM:PCMS is 69:31, 100/100 nm line and space pattern having a good shape is obtained at 120 μC/cm2 which is comparable to the required exposure dose for conventional ACM-MS resist with ACM:MS=50:50. Dry etching resistance of ACM:PCMS resists for Ar gas is also presented.

  8. MiR-320a as a Potential Novel Circulating Biomarker of Arrhythmogenic CardioMyopathy.

    Sommariva, Elena; D'Alessandra, Yuri; Farina, Floriana Maria; Casella, Michela; Cattaneo, Fabio; Catto, Valentina; Chiesa, Mattia; Stadiotti, Ilaria; Brambilla, Silvia; Dello Russo, Antonio; Carbucicchio, Corrado; Vettor, Giulia; Riggio, Daniela; Sandri, Maria Teresa; Barbuti, Andrea; Vernillo, Gianluca; Muratori, Manuela; Dal Ferro, Matteo; Sinagra, Gianfranco; Moimas, Silvia; Giacca, Mauro; Colombo, Gualtiero Ivanoe; Pompilio, Giulio; Tondo, Claudio

    2017-07-06

    Diagnosis of Arrhythmogenic CardioMyopathy (ACM) is challenging and often late after disease onset. No circulating biomarkers are available to date. Given their involvement in several cardiovascular diseases, plasma microRNAs warranted investigation as potential non-invasive diagnostic tools in ACM. We sought to identify circulating microRNAs differentially expressed in ACM with respect to Healthy Controls (HC) and Idiopathic Ventricular Tachycardia patients (IVT), often in differential diagnosis. ACM and HC subjects were screened for plasmatic expression of 377 microRNAs and validation was performed in 36 ACM, 53 HC, 21 IVT. Variable importance in data partition was estimated through Random Forest analysis and accuracy by Receiver Operating Curves. Plasmatic miR-320a showed 0.53 ± 0.04 fold expression difference in ACM vs. HC (p ACM (n = 13) and HC (n = 17) with athletic lifestyle, a ACM precipitating factor. Importantly, ACM patients miR-320a showed 0.78 ± 0.05 fold expression change vs. IVT (p = 0.03). When compared to non-invasive ACM diagnostic parameters, miR-320a ranked highly in discriminating ACM vs. IVT and it increased their accuracy. Finally, miR-320a expression did not correlate with ACM severity. Our data suggest that miR-320a may be considered a novel potential biomarker of ACM, specifically useful in ACM vs. IVT differentiation.

  9. Novel derivatives of aclacinomycin A block cancer cell migration through inhibition of farnesyl transferase.

    Magi, Shigeyuki; Shitara, Tetsuo; Takemoto, Yasushi; Sawada, Masato; Kitagawa, Mitsuhiro; Tashiro, Etsu; Takahashi, Yoshikazu; Imoto, Masaya

    2013-03-01

    In the course of screening for an inhibitor of farnesyl transferase (FTase), we identified two compounds, N-benzyl-aclacinomycin A (ACM) and N-allyl-ACM, which are new derivatives of ACM. N-benzyl-ACM and N-allyl-ACM inhibited FTase activity with IC50 values of 0.86 and 2.93 μM, respectively. Not only ACM but also C-10 epimers of each ACM derivative failed to inhibit FTase. The inhibition of FTase by N-benzyl-ACM and N-allyl-ACM seems to be specific, because these two compounds did not inhibit geranylgeranyltransferase or geranylgeranyl pyrophosphate (GGPP) synthase up to 100 μM. In cultured A431 cells, N-benzyl-ACM and N-allyl-ACM also blocked both the membrane localization of H-Ras and activation of the H-Ras-dependent PI3K/Akt pathway. In addition, they inhibited epidermal growth factor (EGF)-induced migration of A431 cells. Thus, N-benzyl-ACM and N-allyl-ACM inhibited EGF-induced migration of A431 cells by inhibiting the farnesylation of H-Ras and subsequent H-Ras-dependent activation of the PI3K/Akt pathway.

  10. Experimental study to distinguish the effects of methanol slip and water vapour on a high temperature PEM fuel cell at different operating conditions

    Thomas, Sobi; Vang, Jakob Rabjerg; Araya, Samuel Simon

    2017-01-01

    The objective of this paper is to separate out the effects of methanol and water vapour on a high temperature polymer electrolyte membrane fuel cell under different temperatures (160°C and 180°C) and current densities (0.2Acm-2, 0.4Acm-2 and 0.6Acm-2). The degradation rates at the different curre...

  11. A NEW COMBINED LOCAL AND NON-LOCAL PBL MODEL FOR METEOROLOGY AND AIR QUALITY MODELING

    A new version of the Asymmetric Convective Model (ACM) has been developed to describe sub-grid vertical turbulent transport in both meteorology models and air quality models. The new version (ACM2) combines the non-local convective mixing of the original ACM with local eddy diff...

  12. 76 FR 60871 - In the Matter of Certain Toner Cartridges and Components Thereof; Notice of Commission Final...

    2011-09-30

    ...-Toner''); Alpha Image Tech of South El Monte, California (``Alpha Image''); ACM Technologies, Inc. of Corona, California (``ACM''); Virtual Imaging Products Inc. of North York, Ontario; Acecom Inc.--San... Image, Copy Tech, LTT, C&R, ACM, Ink Master, Direct Billing, Ink Tech, QCI, IJSS, Acecom, Ninestar Tech...

  13. Joint Labeling Of Multiple Regions of Interest (Rois) By Enhanced Auto Context Models.

    Kim, Minjeong; Wu, Guorong; Guo, Yanrong; Shen, Dinggang

    2015-04-01

    Accurate segmentation of a set of regions of interest (ROIs) in the brain images is a key step in many neuroscience studies. Due to the complexity of image patterns, many learning-based segmentation methods have been proposed, including auto context model (ACM) that can capture high-level contextual information for guiding segmentation. However, since current ACM can only handle one ROI at a time, neighboring ROIs have to be labeled separately with different ACMs that are trained independently without communicating each other. To address this, we enhance the current single-ROI learning ACM to multi-ROI learning ACM for joint labeling of multiple neighboring ROIs (called e ACM). First, we extend current independently-trained single-ROI ACMs to a set of jointly-trained cross-ROI ACMs, by simultaneous training of ACMs for all spatially-connected ROIs to let them to share their respective intermediate outputs for coordinated labeling of each image point. Then, the context features in each ACM can capture the cross-ROI dependence information from the outputs of other ACMs that are designed for neighboring ROIs. Second, we upgrade the output labeling map of each ACM with the multi-scale representation, thus both local and global context information can be effectively used to increase the robustness in characterizing geometric relationship among neighboring ROIs. Third, we integrate ACM into a multi-atlases segmentation paradigm, for encompassing high variations among subjects. Experiments on LONI LPBA40 dataset show much better performance by our e ACM, compared to the conventional ACM.

  14. Acemetacin cocrystals and salts: structure solution from powder X-ray data and form selection of the piperazine salt.

    Sanphui, Palash; Bolla, Geetha; Nangia, Ashwini; Chernyshev, Vladimir

    2014-03-01

    Acemetacin (ACM) is a non-steroidal anti-inflammatory drug (NSAID), which causes reduced gastric damage compared with indomethacin. However, acemetacin has a tendency to form a less soluble hydrate in the aqueous medium. We noted difficulties in the preparation of cocrystals and salts of acemetacin by mechanochemical methods, because this drug tends to form a hydrate during any kind of solution-based processing. With the objective to discover a solid form of acemetacin that is stable in the aqueous medium, binary adducts were prepared by the melt method to avoid hydration. The coformers/salt formers reported are pyridine carboxamides [nicotinamide (NAM), isonicotinamide (INA), and picolinamide (PAM)], caprolactam (CPR), p-aminobenzoic acid (PABA), and piperazine (PPZ). The structures of an ACM-INA cocrystal and a binary adduct ACM-PABA were solved using single-crystal X-ray diffraction. Other ACM cocrystals, ACM-PAM and ACM-CPR, and the piperazine salt ACM-PPZ were solved from high-resolution powder X-ray diffraction data. The ACM-INA cocrystal is sustained by the acid⋯pyridine heterosynthon and N-H⋯O catemer hydrogen bonds involving the amide group. The acid⋯amide heterosynthon is present in the ACM-PAM cocrystal, while ACM-CPR contains carboxamide dimers of caprolactam along with acid-carbonyl (ACM) hydrogen bonds. The cocrystals ACM-INA, ACM-PAM and ACM-CPR are three-dimensional isostructural. The carboxyl⋯carboxyl synthon in ACM-PABA posed difficulty in assigning the position of the H atom, which may indicate proton disorder. In terms of stability, the salts were found to be relatively stable in pH 7 buffer medium over 24 h, but the cocrystals dissociated to give ACM hydrate during the same time period. The ACM-PPZ salt and ACM-nicotinamide cocrystal dissolve five times faster than the stable hydrate form, whereas the ACM-PABA adduct has 2.5 times faster dissolution rate. The pharmaceutically acceptable piperazine salt of acemetacin exhibits superior

  15. Genetic interrelations in the actinomycin biosynthetic gene clusters of Streptomyces antibioticus IMRU 3720 and Streptomyces chrysomallus ATCC11523, producers of actinomycin X and actinomycin C

    Crnovčić, Ivana; Rückert, Christian; Semsary, Siamak; Lang, Manuel; Kalinowski, Jörn; Keller, Ullrich

    2017-01-01

    Sequencing the actinomycin (acm) biosynthetic gene cluster of Streptomyces antibioticus IMRU 3720, which produces actinomycin X (Acm X), revealed 20 genes organized into a highly similar framework as in the bi-armed acm C biosynthetic gene cluster of Streptomyces chrysomallus but without an attached additional extra arm of orthologues as in the latter. Curiously, the extra arm of the S. chrysomallus gene cluster turned out to perfectly match the single arm of the S. antibioticus gene cluster in the same order of orthologues including the the presence of two pseudogenes, scacmM and scacmN, encoding a cytochrome P450 and its ferredoxin, respectively. Orthologues of the latter genes were both missing in the principal arm of the S. chrysomallus acm C gene cluster. All orthologues of the extra arm showed a G +C-contents different from that of their counterparts in the principal arm. Moreover, the similarities of translation products from the extra arm were all higher to the corresponding translation products of orthologue genes from the S. antibioticus acm X gene cluster than to those encoded by the principal arm of their own gene cluster. This suggests that the duplicated structure of the S. chrysomallus acm C biosynthetic gene cluster evolved from previous fusion between two one-armed acm gene clusters each from a different genetic background. However, while scacmM and scacmN in the extra arm of the S. chrysomallus acm C gene cluster are mutated and therefore are non-functional, their orthologues saacmM and saacmN in the S. antibioticus acm C gene cluster show no defects seemingly encoding active enzymes with functions specific for Acm X biosynthesis. Both acm biosynthetic gene clusters lack a kynurenine-3-monooxygenase gene necessary for biosynthesis of 3-hydroxy-4-methylanthranilic acid, the building block of the Acm chromophore, which suggests participation of a genome-encoded relevant monooxygenase during Acm biosynthesis in both S. chrysomallus and S

  16. Novel active contour model based on multi-variate local Gaussian distribution for local segmentation of MR brain images

    Zheng, Qiang; Li, Honglun; Fan, Baode; Wu, Shuanhu; Xu, Jindong

    2017-12-01

    Active contour model (ACM) has been one of the most widely utilized methods in magnetic resonance (MR) brain image segmentation because of its ability of capturing topology changes. However, most of the existing ACMs only consider single-slice information in MR brain image data, i.e., the information used in ACMs based segmentation method is extracted only from one slice of MR brain image, which cannot take full advantage of the adjacent slice images' information, and cannot satisfy the local segmentation of MR brain images. In this paper, a novel ACM is proposed to solve the problem discussed above, which is based on multi-variate local Gaussian distribution and combines the adjacent slice images' information in MR brain image data to satisfy segmentation. The segmentation is finally achieved through maximizing the likelihood estimation. Experiments demonstrate the advantages of the proposed ACM over the single-slice ACM in local segmentation of MR brain image series.

  17. Generalized Wideband Cyclic MUSIC

    Zhang-Meng Liu

    2009-01-01

    Full Text Available The method of Spectral Correlation-Signal Subspace Fitting (SC-SSF fails to separate wideband cyclostationary signals with coherent second-order cyclic statistics (SOCS. Averaged Cyclic MUSIC (ACM method made up for the drawback to some degree via temporally averaging the cyclic cross-correlation of the array output. This paper interprets ACM from another perspective and proposes a new DOA estimation method by generalizing ACM for wideband cyclostationary signals. The proposed method successfully makes up for the aforementioned drawback of SC-SSF and obtains a more satisfying performance than ACM. It is also demonstrated that ACM is a simplified form of the proposed method when only a single spectral frequency is exploited, and the integration of the frequencies within the signal bandwidth helps the new method to outperform ACM.

  18. Central role for GSK3β in the pathogenesis of arrhythmogenic cardiomyopathy

    Chelko, Stephen P.; Asimaki, Angeliki; Andersen, Peter; Bedja, Djahida; Amat-Alarcon, Nuria; DeMazumder, Deeptankar; Jasti, Ravirasmi; MacRae, Calum A.; Leber, Remo; Kleber, Andre G.; Saffitz, Jeffrey E.; Judge, Daniel P.

    2016-01-01

    Arrhythmogenic cardiomyopathy (ACM) is characterized by redistribution of junctional proteins, arrhythmias, and progressive myocardial injury. We previously reported that SB216763 (SB2), annotated as a GSK3β inhibitor, reverses disease phenotypes in a zebrafish model of ACM. Here, we show that SB2 prevents myocyte injury and cardiac dysfunction in vivo in two murine models of ACM at baseline and in response to exercise. SB2-treated mice with desmosome mutations showed improvements in ventricu...

  19. Ketonization of Proline Residues in the Peptide Chains of Actinomycins by a 4-Oxoproline Synthase.

    Semsary, Siamak; Crnovčić, Ivana; Driller, Ronja; Vater, Joachim; Loll, Bernhard; Keller, Ullrich

    2018-04-04

    X-type actinomycins (Acms) contain 4-hydroxyproline (Acm X 0 ) or 4-oxoproline (Acm X 2 ) in their β-pentapeptide lactone rings, whereas their α ring contains proline. We demonstrate that these Acms are formed through asymmetric condensation of Acm half molecules (Acm halves) containing proline with 4-hydroxyproline- or 4-oxoproline-containing Acm halves. In turn, we show-using an artificial Acm half analogue (PPL 1) with proline in its peptide chain-their conversion into the 4-hydroxyproline- and 4-oxoproline-containing Acm halves, PPL 0 and PPL 2, in mycelial suspensions of Streptomyces antibioticus. Two responsible genes of the Acm X biosynthetic gene cluster of S. antibioticus, saacmM and saacmN, encoding a cytochrome P450 monooxygenase (Cyp) and a ferredoxin were identified. After coexpression in Escherichia coli, their gene products converted PPL 1 into PPL 0 and PPL 2 in vivo as well as in situ in permeabilized cell of the transformed E. coli strain in conjunction with the host-encoded ferredoxin reductase in a NADH (NADPH)-dependent manner. saAcmM has high sequence similarity to the Cyp107Z (Ema) family of Cyps, which can convert avermectin B1 into its keto derivative, 4''-oxoavermectin B1. Determination of the structure of saAcmM reveals high similarity to the Ema structure but with significant differences in residues decorating their active sites, which defines saAcmM and its orthologues as a distinct new family of peptidylprolineketonizing Cyp. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Heterosis for green fruit yield and its components in chilli (Capsicum annuum var. longicum (D.G) Sendt) over environments

    M. P. Patel, A. R. Patel, J.B. Patel and J.A.Patel

    2010-01-01

    Heterosis for green fruits and related characters in chilli was studied in line × tester fashion involving five GMS lines and 10 testers. The hybridsdiffered significantly for all the characters, as evident from their highly significant mean square values. Mean squares due to hybrids ×environments were significant for all the characters except average fruit weight, which indicated more sensitivity of hybrids to environments. Thehybrids ACMS 8 ×IPS -2005 -15, ACMS 5 × IPS -2005 -15, ACMS 6 × A...

  1. Growth and acid production of Lactobacillus delbrueckii ssp. bulgaricus ATCC 11842 in the fermentation of algal carcass.

    Li, C; Zhang, G F; Mao, X; Wang, J Y; Duan, C Y; Wang, Z J; Liu, L B

    2016-06-01

    Algal carcass is a low-value byproduct of algae after its conversion to biodiesel. Dried algal carcass is rich in protein, carbohydrate, and multiple amino acids, and it is typically well suited for growth and acid production of lactic acid bacteria. In this study, Lactobacillus delbrueckii ssp. bulgaricus ATCC 11842 was used to ferment different algal carcass media (ACM), including 2% ACM, 2% ACM with 1.9% glucose (ACM-G), and 2% ACM with 1.9% glucose and 2g/L amino acid mixture (ACM-GA). Concentrations of organic acids (lactic acid and acetic acid), acetyl-CoA, and ATP were analyzed by HPLC, and activities of lactate dehydrogenase (LDH), acetokinase (ACK), pyruvate kinase (PK), and phosphofructokinase (PFK) were determined by using a chemical approach. The growth of L. bulgaricus cells in ACM-GA was close to that in the control medium (de Man, Rogosa, and Sharpe). Lactic acid and acetic acid contents were greatly reduced when L. bulgaricus cells were grown in ACM compared with the control medium. Acetyl-CoA content varied with organic acid content and was increased in cells grown in different ACM compared with the control medium. The ATP content of L. bulgaricus cells in ACM was reduced compared with that of cells grown in the control medium. Activities of PFK and ACK of L. bulgaricus cells grown in ACM were higher and those of PK and LDH were lower compared with the control. Thus, ACM rich in nutrients may serve as an excellent substrate for growth by lactic acid bacteria, and addition of appropriate amounts of glucose and amino acids can improve growth and acid production. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  2. Interactive Synthesis of Code Level Security Rules

    2017-04-01

    Proceedings of the 9th ACM conference on Computer and communications security, pages 235–244. ACM, 2002. [19] J. Davis. Hacking of government computers...Inductive programming meets the real world. Communications of the ACM, 58(11):90–99, 2015. [24] S. Hallem, B. Chelf, Y. Xie, and D. Engler. A system and...Software Engineering, pages 462–473. ACM, 2015. [37] S. H. Muggleton, D. Lin, and A. Tamaddoni-Nezhad. Meta-interpretive learning of higher- order dyadic

  3. Influence of miscibility phenomenon on crystalline polymorph transition in poly(vinylidene fluoride)/acrylic rubber/clay nanocomposite hybrid.

    Abolhasani, Mohammad Mahdi; Naebe, Minoo; Jalali-Arani, Azam; Guo, Qipeng

    2014-01-01

    In this paper, intercalation of nanoclay in the miscible polymer blend of poly(vinylidene fluoride) (PVDF) and acrylic rubber(ACM) was studied. X-ray diffraction was used to investigate the formation of nanoscale polymer blend/clay hybrid. Infrared spectroscopy and X-ray analysis revealed the coexistence of β and γ crystalline forms in PVDF/Clay nanocomposite while α crystalline form was found to be dominant in PVDF/ACM/Clay miscible hybrids. Flory-Huggins interaction parameter (B) was used to further explain the miscibility phenomenon observed. The B parameter was determined by combining the melting point depression and the binary interaction model. The estimated B values for the ternary PVDF/ACM/Clay and PVDF/ACM pairs were all negative, showing both proper intercalation of the polymer melt into the nanoclay galleries and the good miscibility of PVDF and ACM blend. The B value for the PVDF/ACM blend was almost the same as that measured for the PVDF/ACM/Clay hybrid, suggesting that PVDF chains in nanocomposite hybrids interact with ACM chains and that nanoclay in hybrid systems is wrapped by ACM molecules.

  4. Influence of miscibility phenomenon on crystalline polymorph transition in poly(vinylidene fluoride/acrylic rubber/clay nanocomposite hybrid.

    Mohammad Mahdi Abolhasani

    Full Text Available In this paper, intercalation of nanoclay in the miscible polymer blend of poly(vinylidene fluoride (PVDF and acrylic rubber(ACM was studied. X-ray diffraction was used to investigate the formation of nanoscale polymer blend/clay hybrid. Infrared spectroscopy and X-ray analysis revealed the coexistence of β and γ crystalline forms in PVDF/Clay nanocomposite while α crystalline form was found to be dominant in PVDF/ACM/Clay miscible hybrids. Flory-Huggins interaction parameter (B was used to further explain the miscibility phenomenon observed. The B parameter was determined by combining the melting point depression and the binary interaction model. The estimated B values for the ternary PVDF/ACM/Clay and PVDF/ACM pairs were all negative, showing both proper intercalation of the polymer melt into the nanoclay galleries and the good miscibility of PVDF and ACM blend. The B value for the PVDF/ACM blend was almost the same as that measured for the PVDF/ACM/Clay hybrid, suggesting that PVDF chains in nanocomposite hybrids interact with ACM chains and that nanoclay in hybrid systems is wrapped by ACM molecules.

  5. Influence of Miscibility Phenomenon on Crystalline Polymorph Transition in Poly(Vinylidene Fluoride)/Acrylic Rubber/Clay Nanocomposite Hybrid

    Abolhasani, Mohammad Mahdi; Naebe, Minoo; Jalali-Arani, Azam; Guo, Qipeng

    2014-01-01

    In this paper, intercalation of nanoclay in the miscible polymer blend of poly(vinylidene fluoride) (PVDF) and acrylic rubber(ACM) was studied. X-ray diffraction was used to investigate the formation of nanoscale polymer blend/clay hybrid. Infrared spectroscopy and X-ray analysis revealed the coexistence of β and γ crystalline forms in PVDF/Clay nanocomposite while α crystalline form was found to be dominant in PVDF/ACM/Clay miscible hybrids. Flory-Huggins interaction parameter (B) was used to further explain the miscibility phenomenon observed. The B parameter was determined by combining the melting point depression and the binary interaction model. The estimated B values for the ternary PVDF/ACM/Clay and PVDF/ACM pairs were all negative, showing both proper intercalation of the polymer melt into the nanoclay galleries and the good miscibility of PVDF and ACM blend. The B value for the PVDF/ACM blend was almost the same as that measured for the PVDF/ACM/Clay hybrid, suggesting that PVDF chains in nanocomposite hybrids interact with ACM chains and that nanoclay in hybrid systems is wrapped by ACM molecules. PMID:24551141

  6. Central role for GSK3β in the pathogenesis of arrhythmogenic cardiomyopathy.

    Chelko, Stephen P; Asimaki, Angeliki; Andersen, Peter; Bedja, Djahida; Amat-Alarcon, Nuria; DeMazumder, Deeptankar; Jasti, Ravirasmi; MacRae, Calum A; Leber, Remo; Kleber, Andre G; Saffitz, Jeffrey E; Judge, Daniel P

    2016-04-21

    Arrhythmogenic cardiomyopathy (ACM) is characterized by redistribution of junctional proteins, arrhythmias, and progressive myocardial injury. We previously reported that SB216763 (SB2), annotated as a GSK3β inhibitor, reverses disease phenotypes in a zebrafish model of ACM. Here, we show that SB2 prevents myocyte injury and cardiac dysfunction in vivo in two murine models of ACM at baseline and in response to exercise. SB2-treated mice with desmosome mutations showed improvements in ventricular ectopy and myocardial fibrosis/inflammation as compared with vehicle-treated (Veh-treated) mice. GSK3β inhibition improved left ventricle function and survival in sedentary and exercised Dsg2 mut/mut mice compared with Veh-treated Dsg2 mut/mut mice and normalized intercalated disc (ID) protein distribution in both mutant mice. GSK3β showed diffuse cytoplasmic localization in control myocytes but ID redistribution in ACM mice. Identical GSK3β redistribution is present in ACM patient myocardium but not in normal hearts or other cardiomyopathies. SB2 reduced total GSK3β protein levels but not phosphorylated Ser 9-GSK3β in ACM mice. Constitutively active GSK3β worsens ACM in mutant mice, while GSK3β shRNA silencing in ACM cardiomyocytes prevents abnormal ID protein distribution. These results highlight a central role for GSKβ in the complex phenotype of ACM and provide further evidence that pharmacologic GSKβ inhibition improves cardiomyopathies due to desmosome mutations.

  7. Evaluation of rotor-bearing system dynamic response to unbalance. [air conditioning equipment

    Thaller, R. E.; Ozimek, D. W.

    1979-01-01

    The vibration environment within air conditioner rotating machinery referred to as an air cycle machine (ACM) was investigated to effectively increase ACM reliability. To assist in the selection of design changes which would result in improved ACM performance, various design modifications were incorporated into a baseline ACM configuration. For each design change, testing was conducted with the best balance achieveable (baseline) and with various degrees of unbalance. Relationships between unbalance (within the context of design changes) and the parameters associated with design goals were established. The results of rotor dynamics tests used to establish these relationships are presented.

  8. Cancer recurrence and mortality after pediatric heart transplantation for anthracycline cardiomyopathy: A report from the Pediatric Heart Transplant Study (PHTS) group.

    Bock, Matthew J; Pahl, Elfriede; Rusconi, Paolo G; Boyle, Gerard J; Parent, John J; Twist, Clare J; Kirklin, James K; Pruitt, Elizabeth; Bernstein, Daniel

    2017-08-01

    We aimed to determine whether malignancy after pediatric HTx for ACM affects overall post-HTx survival. Patients ACM in the PHTS database between 1993 and 2014 were compared to those with DCM. A 2:1 matched DCM cohort was also compared. Wait-list and post-HTx survival, along with freedom from common HTx complications, were compared. Eighty subjects were listed due to ACM, whereas 1985 were listed for DCM. Although wait-list survival was higher in the ACM group, post-HTx survival was lower for the ACM cohort. Neither difference persisted in the matched cohort analysis. Primary cause of death in the ACM group was infection, which was higher than the DCM group. Malignancy rates were not different. All ACM malignancies were due to PTLD without primary cancer recurrence or SMN. Long-term graft survival after pediatric HTx for ACM is no different than for matched DCM peers, nor is there an increased risk of any malignancy. However, risk of infection and death from infection after HTx are higher in the ACM group. Further studies are needed to assess the effects of prior chemotherapy on susceptibility to infection in this group. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  9. Data Acquisition System Design for Advanced Core-Cooling Mechanism Experiment

    Zhang, Ziyang; Tian, Fang; Zhang, Tao; Wang, Shen

    2011-01-01

    Data Acquisition System (DAS) design for Advanced Core-Cooling Mechanism Experiment(ACME) is studied in the paper. DAS is an important connection between test facility and result analysis. Firstly, it introduces DAS and its design requirement for ACME. Nearly one thousand data resources need record in ACME. They have different types and acquisition frequencies. In order to record these data, a large scale and high speed layered data acquisition system is developed. Secondly, it discusses the DAS design for ACME, including the analog signal adjusting circuits, clock circuit design, sampling frequencies, data storage and transmission by large database system, anti-interference and etc. Analog signal adjusting circuits are necessary to deal with different kinds of input data to gain standard data resources. Some data change slowly and others change in several seconds according to the test performed on ACME. So it is difficult to use uniform sampling frequencies, and a layered data acquisition system is introduced. A large database is built to store data for ACME test, which keeps data safer and makes subsequent data handling more convenient. A database hot backup is also applied to ensure data safety. The software of DAS is built by Labview, which can provide intuitionist result and friendly interface. Another important function of DAS is the ACME safety protection. Finally, the characteristics and improvement of DAS for ACME is analyzed compared to other test facility. Besides friendly user interface, DAS of ACME can also assure higher data precision and sampling frequency

  10. Genetic basis of arrhythmogenic cardiomyopathy.

    Karmouch, Jennifer; Protonotarios, Alexandros; Syrris, Petros

    2018-05-01

    To date 16 genes have been associated with arrhythmogenic cardiomyopathy (ACM). Mutations in these genes can lead to a broad spectrum of phenotypic expression ranging from disease affecting predominantly the right or left ventricle, to biventricular subtypes. Understanding the genetic causes of ACM is important in diagnosis and management of the disorder. This review summarizes recent advances in molecular genetics and discusses the application of next-generation sequencing technology in genetic testing in ACM. Use of next-generation sequencing methods has resulted in the identification of novel causative variants and genes for ACM. The involvement of filamin C in ACM demonstrates the genetic overlap between ACM and other types of cardiomyopathy. Putative pathogenic variants have been detected in cadherin 2 gene, a protein involved in cell adhesion. Large genomic rearrangements in desmosome genes have been systematically investigated in a cohort of ACM patients. Recent studies have identified novel causes of ACM providing new insights into the genetic spectrum of the disease and highlighting an overlapping phenotype between ACM and dilated cardiomyopathy. Next-generation sequencing is a useful tool for research and genetic diagnostic screening but interpretation of identified sequence variants requires caution and should be performed in specialized centres.

  11. Source localization of intermittent rhythmic delta activity in a patient with acute confusional migraine: cross-spectral analysis using standardized low-resolution brain electromagnetic tomography (sLORETA).

    Kim, Dae-Eun; Shin, Jung-Hyun; Kim, Young-Hoon; Eom, Tae-Hoon; Kim, Sung-Hun; Kim, Jung-Min

    2016-01-01

    Acute confusional migraine (ACM) shows typical electroencephalography (EEG) patterns of diffuse delta slowing and frontal intermittent rhythmic delta activity (FIRDA). The pathophysiology of ACM is still unclear but these patterns suggest neuronal dysfunction in specific brain areas. We performed source localization analysis of IRDA (in the frequency band of 1-3.5 Hz) to better understand the ACM mechanism. Typical IRDA EEG patterns were recorded in a patient with ACM during the acute stage. A second EEG was obtained after recovery from ACM. To identify source localization of IRDA, statistical non-parametric mapping using standardized low-resolution brain electromagnetic tomography was performed for the delta frequency band comparisons between ACM attack and non-attack periods. A difference in the current density maximum was found in the dorsal anterior cingulated cortex (ACC). The significant differences were widely distributed over the frontal, parietal, temporal and limbic lobe, paracentral lobule and insula and were predominant in the left hemisphere. Dorsal ACC dysfunction was demonstrated for the first time in a patient with ACM in this source localization analysis of IRDA. The ACC plays an important role in the frontal attentional control system and acute confusion. This dysfunction of the dorsal ACC might represent an important ACM pathophysiology.

  12. Dry friction damping couple at high frequencies

    Půst, Ladislav; Pešek, Luděk; Košina, Jan; Radolfová, Alena

    2014-01-01

    Roč. 8, č. 1 (2014), s. 91-100 ISSN 1802-680X Institutional support: RVO:61388998 Keywords : dry friction * damping * high frequencies Subject RIV: BI - Acoustics http://www.kme.zcu.cz/acm/acm/article/view/239/265

  13. Prioritizing Asbestos Removal from Various Facilities Using the INSIGHT II+ Expert System

    1986-07-01

    34chronic lung disease" (30), the Johns-Manville Company was established in 1902. This company was to play a dramatic role , socially, politically and...determine recommendations for controlling the asbestos fiber release from the ACM. ’Pr iasbes ’ queries the user about the condition of the ACM through

  14. Do adaptive comanagement processes lead to adaptive comanagement outcomes? A multicase study of long-term outcomes associated with the national riparian service team's place-based riparian assistance

    Jill A. Smedstad; Hannah. Gosnell

    2013-01-01

    Adaptive comanagement (ACM) is a novel approach to environmental governance that combines the dynamic learning features of adaptive management with the linking and network features of collaborative management. There is growing interest in the potential for ACM to resolve conflicts around natural resource management and contribute to greater social and ecological...

  15. Cloud Computing at the Tactical Edge

    2012-10-01

    Web Services and Cloud Computing to Create Next-Generation Mobile Applications,” 627-634. Proceedings of the 24th ACM SIGPLAN Conference Companion on...the 1st Workshop on Mobile Middleware. Leuven, Belgium, December 2008. ACM, 2008. [Kumar 2010] Kumar, K. & Lu, Y. “ Cloud Computing for Mobile Users

  16. Numerical approximation of flow in a symmetric channel with vibrating walls

    Sváček, P.; Horáček, Jaromír

    2010-01-01

    Roč. 4, č. 2 (2010), s. 225-236 ISSN 1802-680X R&D Projects: GA MŠk OC09019 Institutional research plan: CEZ:AV0Z20760514 Keywords : biomechanics of voice production * incompressible Navier-Stokes equations * ALE method Subject RIV: BI - Acoustics http://www.kme.zcu.cz/acm/index.php/acm/article/view/62

  17. Micro-structure Engineering of InGaN/GaN Quantum Wells for High Brightness Light Emitting Devices

    Shen, Chao

    2013-01-01

    diameter (D) micro-LED-pillar was achieved, compared to that of a 200 μm diameter LED (20 A/cm2), both at 10 V bias voltage. In addition, an increase in sustained quantum efficiency from 70.2% to 83.7% at high injection current density (200 A/cm2

  18. De publieke handhavingsprocedures van het mededingingsrecht in het licht van de mensenrechten

    Beumer, A.E.

    2016-01-01

    Public enforcement of competition law is in the hands of the Netherlands Authority for Consumers & Markets (ACM). The ACM has a wide variety of instruments at its disposal to combat unfair competition. The increasing attention to administrative fines, the qualification of the administrative fine as

  19. The influence of underwater data transmission sounds on the displacement behaviour of captive harbour seals (Phoca vitulina)

    Kastelein, R.A.; Heul, S. van der; Verboom, W.C.; Triesscheijn, R.J.V.; Jennings, N.V.

    2006-01-01

    To prevent grounding of ships and collisions between ships in shallow coastal waters, an underwater data collection and communication network (ACME) using underwater sounds to encode and transmit data is currently under development. Marine mammals might be affected by ACME sounds since they may use

  20. OJPOT: Online Judge & Practice Oriented Teaching Idea in Programming Courses

    Wang, Gui Ping; Chen, Shu Yu; Yang, Xin; Feng, Rui

    2016-01-01

    Practical abilities are important for students from majors including Computer Science and Engineering, and Electrical Engineering. Along with the popularity of ACM International Collegiate Programming Contest (ACM/ICPC) and other programming contests, online judge (OJ) websites achieve rapid development, thus providing a new kind of programming…

  1. Semi-analytical stochastic analysis of the generalized van der Pol system

    Náprstek, Jiří; Fischer, Cyril

    (2018) ISSN 1802-680X R&D Projects: GA ČR(CZ) GA15-01035S Institutional support: RVO:68378297 Keywords : stochastic stability * generalized van der Pol system * stochastic averaging * limit cycles Subject RIV: JM - Building Engineering OBOR OECD: Construction engineering, Municipal and structural engineering https://www.kme.zcu.cz/acm/acm/article/view/407

  2. Research Article Special Issue

    2016-05-15

    May 15, 2016 ... ... such as [14,17]. In [19] this is introduced as atomic verification capability. Here .... 26th ACM Symposium on Theory of Computing,pages 544–553. ACM, 1994. ... Self-tallying elections and perfect ballot secrecy. In Proc. 5th.

  3. Determination of magnetic resonance imaging biomarkers for multiple sclerosis treatment effects

    Lyksborg, Mark

    based on the ACM method. Using ACM, localized statistical differences were detected in the bilateral motor tracts. The most interesting result of the lesion segmentation method study, was that it achieved a segmentation performance which was batter than two competing methods relative to the manual...

  4. Overview of Special Issue

    Hiemstra, Djoerd; Harman, Donna; Allan, James; Kelly, Diane; Belkin, Nicholas J.; Bennet, Paul; Callan, Jamie; Clarke, Charles; Diaz, Fernando; Dumais, Susan; Ferro, Nicola; Harman, Donna; Ruthven, Ian; Sakai, Tetsuya; Smucker, Mark D.; Zobel, Justin

    2017-01-01

    This special issue of SIGIR Forum marks the 40th anniversary of the ACM SIGIR Conference by showcasing papers selected for the ACM SIGIR Test of Time Award from the years 1978-2001. These papers document the history and evolution of IR research and practice, and illustrate the intellectual impact

  5. Active contour modes Crisp: new technique for segmentation of the lungs in CT images

    Reboucas Filho, Pedro Pedrosa; Cortez, Paulo Cesar; Holanda, Marcelo Alcantara

    2011-01-01

    This paper proposes a new active contour model (ACM), called ACM Crisp, and evaluates the segmentation of lungs in computed tomography (CT) images. An ACM draws a curve around or within the object of interest. This curve changes its shape, when some energy acts on it and moves towards the edges of the object. This process is performed by successive iterations of minimization of a given energy, associated with the curve. The ACMs described in the literature have limitations when used for segmentations of CT lung images. The ACM Crisp model overcomes these limitations, since it proposes automatic initiation and new external energy based on rules and radiological pulmonary densities. The paper compares other ACMs with the proposed method, which is shown to be superior. In order to validate the algorithm a medical expert in the field of Pulmonology of the Walter Cantidio University Hospital from the Federal University of Ceara carried out a qualitative analysis. In these analyses 100 CT lung images were used. The segmentation efficiency was evaluated into 5 categories with the following results for the ACM Crisp: 73% excellent, without errors, 20% acceptable, with small errors, and 7% reasonable, with large errors, 0% poor, covering only a small part of the lung, and 0% very bad, making a totally incorrect segmentation. In conclusion the ACM Crisp is considered a useful algorithm to segment CT lung images, and with potential to integrate medical diagnosis systems. (author)

  6. Enhancement of tumor cell killing in vitro by pre- and post-irradiation exposure to aclacinomycin A

    Bill, C.A.; Mendoza, A.; Vrdoljak, E.; Tofilon, P.J.

    1993-01-01

    Aclacinomycin A (ACM), a potent inducer of leukemic cell differentiation, significantly enhances the radiosensitivity of a human colon tumor cell line (Clone A) when cultures are exposed to 15-nM concentrations for 3 days before irradiation. We now demonstrate that incubation with ACM after irradiation can also enhance Clone A cell killing. The maximum increase in cell killing, based on colony-forming ability, occurred when Clone A cells were exposed for 1 h to 5 μM ACM model added 1 or 2 h after irradiation. The post-irradiation ACM protocol reduced the terminal slope (as reflected by D o ) of the radiation cell survival curve with no change in the low-dose, shoulder region of the curve (D q value). In contrast, for pre-irradiation treatment with ACM (15 nM, 3 days), the shoulder region of the curve was reduced with no change in the terminal slope. For pre- and post-irradiation ACM treatment the dose enhancement factors at 0.10 survival were 1.22 and 1.28, respectively. When ACM was given both before and after irradiation both the shoulder and terminal slope values decreased to produce a dose enhancement factor at a surviving fraction of 0.10 of 1.50. These data suggest that the enhanced cell killing produced by pre- and post-irradiation treatment with ACM is achieved through different mechanisms. (author) 26 refs., 3 tabs., 2 figs

  7. Proceedings from the Annual Army Environmental R&D Symposium (16th) Held 23-25 June 1992 at Fort Magruder Inn and Conference Center, Williamsburg, Virginia

    1992-06-01

    photoactivity. The second prong was to evaluate the perovskite materials to utilize the lattice oxygen for the oxidation step and was found unsuccessful...Loalized 0 Distributed (*24) WowK damage to ACM. Q Yes 0 NO 0 Lca -Hzed 0 Distributed (25) Proximity (P) of ACM to repaWrromzine mainm uin A. Friable

  8. From Intra-transaction to Generalized Inter-transaction: Landscaping Multidimensional Contexts in Association Rule Mining

    Li, Q; Feng, L.; Wong, A.K.Y.

    The problem of mining multidimensional inter-transactional association rules was recently introduced in [ACM Trans. Inform. Syst. 18(4) (2000) 423; Proc. of the ACM SIGMOD Workshop on Research Issues on Data Mining and Knowledge Discovery, Seattle, Washington, June 1998, p. 12:1]. It extends the

  9. The Snackbot: Documenting the Design of a Robot for Long-term Human-Robot Interaction

    2009-03-01

    distributed robots. Proceedings of the Computer Supported Cooperative Work Conference’02. NY: ACM Press. [18] Kanda, T., Takayuki , H., Eaton, D., and...humanoid robots. Proceedings of HRI’06. New York, NY: ACM Press, 351-352. [23] Nabe, S., Kanda, T., Hiraki , K., Ishiguro, H., Kogure, K., and Hagita

  10. Extending quantum efficiency roll-over threshold with compositionally graded InGaN/GaN LED

    Mishra, Pawan; Ng, Tien Khee; Janjua, Bilal; Shen, Chao; Eid, Jessica; Alyamani, Ahmed Y.; El-Desouki, Munir M.; Ooi, Boon S.

    2014-01-01

    We report a significant improvement in the electrical characteristic of compositionally graded InGaN/GaN multiple-quantum-well (MQWs) micro-LED. The efficiency droop in this device occurred at ∼20 times higher injection levels (∼275 A/cm2) compared to a conventional step-MQWs microLED (∼14 A/cm2).

  11. Novel Acetone Metabolism in a Propane-Utilizing Bacterium, Gordonia sp. Strain TY-5▿

    Kotani, Tetsuya; Yurimoto, Hiroya; Kato, Nobuo; Sakai, Yasuyoshi

    2007-01-01

    In the propane-utilizing bacterium Gordonia sp. strain TY-5, propane was shown to be oxidized to 2-propanol and then further oxidized to acetone. In this study, the subsequent metabolism of acetone was studied. Acetone-induced proteins were found in extracts of cells induced by acetone, and a gene cluster designated acmAB was cloned on the basis of the N-terminal amino acid sequences of acetone-induced proteins. The acmA and acmB genes encode a Baeyer-Villiger monooxygenase (BVMO) and esterase, respectively. The BVMO encoded by acmA was purified from acetone-induced cells of Gordonia sp. strain TY-5 and characterized. The BVMO exhibited NADPH-dependent oxidation activity for linear ketones (C3 to C10) and cyclic ketones (C4 to C8). Escherichia coli expressing the acmA gene oxidized acetone to methyl acetate, and E. coli expressing the acmB gene hydrolyzed methyl acetate. Northern blot analyses revealed that polycistronic transcription of the acmAB gene cluster was induced by propane, 2-propanol, and acetone. These results indicate that the acmAB gene products play an important role in the metabolism of acetone derived from propane oxidation and clarify the propane metabolism pathway of strain TY-5 (propane → 2-propanol → acetone → methyl acetate → acetic acid + methanol). This paper provides the first evidence for BVMO-dependent acetone metabolism. PMID:17071761

  12. Application of the Monte Carlo method for investigation of dynamical parameters of rotors supported by magnetorheological squeeze film damping devices

    Zapoměl, Jaroslav; Ferfecki, Petr; Kozánek, Jan

    2014-01-01

    Roč. 8, č. 1 (2014), s. 129-138 ISSN 1802-680X Institutional support: RVO:61388998 Keywords : uncertain parameters of rigid motors * magnetorheological dampers * force transmission * Monte Carlo method Subject RIV: BI - Acoustics http://www.kme.zcu.cz/acm/acm/article/view/247/275

  13. Automatic Configuration of Programmable Logic Controller Emulators

    2015-03-01

    download.php?articleid= sec v6 n12 2013 3 . [FGM+99] Roy Fielding, Jim Gettys, Jeffrey Mogul, Henrik Frystyk, Larry Masin- ter, Paul Leach, and Tim...2011 ACM SIGCOMM Conference on, IMC ’11, pages 397–412, New York, NY, USA, 2011. ACM. [LBZH13] Patrick LaRoche, Aimee Burrows , and A. Nur Zincir

  14. Vibration of imperfect rotating disk

    Půst, Ladislav; Pešek, Luděk

    2011-01-01

    Roč. 5, č. 2 (2011), s. 205-216 ISSN 1802-680X R&D Projects: GA ČR GA101/09/1166 Institutional research plan: CEZ:AV0Z20760514 Keywords : bladed disk * imperfect disk * travelling waves Subject RIV: BI - Acoustics http://www.kme.zcu.cz/acm/index.php/acm/article/view/86

  15. 78 FR 18533 - Airworthiness Directives; Lindstrand Hot Air Balloons Ltd Appliances

    2013-03-27

    ... Airworthiness Directives; Lindstrand Hot Air Balloons Ltd Appliances AGENCY: Federal Aviation Administration... Hot Air Balloons Ltd female ACME threaded hose connectors, part numbers HS6139 and HS6144, installed... follows: * * * * * (c) Applicability This AD applies to Lindstrand Hot Air Balloons Ltd female ACME...

  16. System approach to development of professional competence of ...

    This article examines the issue of developing the professional competence of students and managers with the use of acme logical technologies. The influence of acme logical technologies, which are used in professional-oriented creative projects, is regarded, considering its effect on the development of professional ...

  17. THE BERKELEY DATA ANALYSIS SYSTEM (BDAS): AN OPEN SOURCE PLATFORM FOR BIG DATA ANALYTICS

    2017-09-01

    duplication and overlap, as well as variations in schemas, quality, and provenance. • Diversity of queries and users: The factors outlined above mean...Reliable Approximate Query Processing Systems. ACM SIGMOD, 2014. [30] Jiannan Wang, Sanjay Krishnan, Michael Franklin, Ken Goldberg , Tim Kraska, Tova... Goldberg . A Methodology for Learning, Analyzing, and Mitigating Social Influence Bias in Recommender Systems. ACM Conference on Recommender Systems

  18. A Type System For Certified Runtime Type Analysis

    2002-12-01

    1999 ACM SIGPLAN International Conf. on Functional Pro- gramming (ICFP’99), pages 183–196. ACM Press, September 1999. [Min97] Yasuhiko Minamide. Full...lifting of type parameters. Technical report, RIMS, Kyoto University, 1997. [MMH96] Yasuhiko Minamide, Greg Morrisett, and Robert Harper. Typed

  19. Extending quantum efficiency roll-over threshold with compositionally graded InGaN/GaN LED

    Mishra, Pawan

    2014-12-01

    We report a significant improvement in the electrical characteristic of compositionally graded InGaN/GaN multiple-quantum-well (MQWs) micro-LED. The efficiency droop in this device occurred at ∼20 times higher injection levels (∼275 A/cm2) compared to a conventional step-MQWs microLED (∼14 A/cm2).

  20. Ruptura de Tendones Extensores de Dedos por Cubito Plus Idiopático Bilateral

    Gustavo Alberto Breglia

    2012-11-01

    Full Text Available Background: Hyaline cartilage has only a very restricted capability of regeneration in the adult. The incidence of chondral lesions at the knee is high, especially those of Grade II/III (Outerbridge. Therapies combining cells and biological scaffolds are promising biological approaches for the treatment of cartilage defects. The aim of this study is to analyze the characteristics of in vitro culture of human chondrocytes on decellularized amniochorionic membrane (ACM. Methods: Between December 2010 and December 2011, 16 samples of cartilage from a living donor were processed, but only 7 of them were analyzed. Chondrocytes were grown and amplified on plastic and on ACM. The following analyses were carried out with those cells: interactions between cells and ACM; ACM capacity as a matrix for cells; and behavior of cells cultured on ACM. Results: In vitro chondrocytes exhibited phenotypic changes in the presence of ACM. The cells were able to adhere and remain on the spongy region of the membrane. Electron microscopy of cultured ACM showed cells, well preserved organelles, endoplasmic reticulum and desmosomes junctions. Conclusions: The feasibility of culturing chondrocytes on ACM was shown in this work. The cells were able to adhere, remain and differentiate on this membrane during the study period.

  1. Dedifferentiation, Proliferation, and Redifferentiation of Adult Mammalian Cardiomyocytes After Ischemic Injury.

    Wang, Wei Eric; Li, Liangpeng; Xia, Xuewei; Fu, Wenbin; Liao, Qiao; Lan, Cong; Yang, Dezhong; Chen, Hongmei; Yue, Rongchuan; Zeng, Cindy; Zhou, Lin; Zhou, Bin; Duan, Dayue Darrel; Chen, Xiongwen; Houser, Steven R; Zeng, Chunyu

    2017-08-29

    Adult mammalian hearts have a limited ability to generate new cardiomyocytes. Proliferation of existing adult cardiomyocytes (ACMs) is a potential source of new cardiomyocytes. Understanding the fundamental biology of ACM proliferation could be of great clinical significance for treating myocardial infarction (MI). We aim to understand the process and regulation of ACM proliferation and its role in new cardiomyocyte formation of post-MI mouse hearts. β-Actin-green fluorescent protein transgenic mice and fate-mapping Myh6-MerCreMer-tdTomato/lacZ mice were used to trace the fate of ACMs. In a coculture system with neonatal rat ventricular myocytes, ACM proliferation was documented with clear evidence of cytokinesis observed with time-lapse imaging. Cardiomyocyte proliferation in the adult mouse post-MI heart was detected by cell cycle markers and 5-ethynyl-2-deoxyuridine incorporation analysis. Echocardiography was used to measure cardiac function, and histology was performed to determine infarction size. In vitro, mononucleated and bi/multinucleated ACMs were able to proliferate at a similar rate (7.0%) in the coculture. Dedifferentiation proceeded ACM proliferation, which was followed by redifferentiation. Redifferentiation was essential to endow the daughter cells with cardiomyocyte contractile function. Intercellular propagation of Ca 2+ from contracting neonatal rat ventricular myocytes into ACM daughter cells was required to activate the Ca 2+ -dependent calcineurin-nuclear factor of activated T-cell signaling pathway to induce ACM redifferentiation. The properties of neonatal rat ventricular myocyte Ca 2+ transients influenced the rate of ACM redifferentiation. Hypoxia impaired the function of gap junctions by dephosphorylating its component protein connexin 43, the major mediator of intercellular Ca 2+ propagation between cardiomyocytes, thereby impairing ACM redifferentiation. In vivo, ACM proliferation was found primarily in the MI border zone. An ischemia

  2. Effect of electrolyte concentration on performance of supercapacitor carbon electrode from fibers of oil palm empty fruit bunches

    Farma, R.; Awitdrus,; Taer, E.; Deraman, M.; Talib, I. A.; Omar, R.; Ishak, M. M.; Basri, N. H.; Dolah, B. N. M.

    2015-01-01

    Fibers of oil palm empty fruit bunches were used to produce self-adhesive carbon grains (SACG). The SACG green monoliths were carbonized in N 2 environment at 800°C to produce carbon monoliths (CM) and the CM was CO 2 activated at 800°C for 4 hour to produce activated carbon monolith electrodes (ACM). The physical properties of the CMs and ACMs were investigated using X-ray diffraction, field emission scanning electron microscopy and nitrogen adsorption-desorption. ACMs were used as electrode to fabricate symmetry supercapacitor cells and the cells which used H 2 SO 4 electrolyte at 0.5, 1.0 and 1.5 M were investigated using electrochemical impedance spectroscopy, cyclic voltammetry and galvanostatic charge-discharge standard techniques. In this paper we report the physical properties of the ACM electrodes and the effect of electrolyte concentration on the electrochemical properties the ACM electrodes

  3. Genetic interrelations in the actinomycin biosynthetic gene clusters of Streptomyces antibioticus IMRU 3720 and Streptomyces chrysomallus ATCC11523, producers of actinomycin X and actinomycin C

    Crnovčić I

    2017-04-01

    Full Text Available Ivana Crnovčić,1 Christian Rückert,2 Siamak Semsary,1 Manuel Lang,1 Jörn Kalinowski,2 Ullrich Keller1 1Institut für Chemie, Technische Universität Berlin, Berlin-Charlottenburg, 2Technology Platform Genomics, Center for Biotechnology, Bielefeld University, Bielefeld, Germany Abstract: Sequencing the actinomycin (acm biosynthetic gene cluster of Streptomyces antibioticus IMRU 3720, which produces actinomycin X (Acm X, revealed 20 genes organized into a highly similar framework as in the bi-armed acm C biosynthetic gene cluster of Streptomyces chrysomallus but without an attached additional extra arm of orthologues as in the latter. Curiously, the extra arm of the S. chrysomallus gene cluster turned out to perfectly match the single arm of the S. antibioticus gene cluster in the same order of orthologues including the the presence of two pseudogenes, scacmM and scacmN, encoding a cytochrome P450 and its ferredoxin, respectively. Orthologues of the latter genes were both missing in the principal arm of the S. chrysomallus acm C gene cluster. All orthologues of the extra arm showed a G +C-contents different from that of their counterparts in the principal arm. Moreover, the similarities of translation products from the extra arm were all higher to the corresponding translation products of orthologue genes from the S. antibioticus acm X gene cluster than to those encoded by the principal arm of their own gene cluster. This suggests that the duplicated structure of the S. chrysomallus acm C biosynthetic gene cluster evolved from previous fusion between two one-armed acm gene clusters each from a different genetic background. However, while scacmM and scacmN in the extra arm of the S. chrysomallus acm C gene cluster are mutated and therefore are non-functional, their orthologues saacmM and saacmN in the S. antibioticus acm C gene cluster show no defects seemingly encoding active enzymes with functions specific for Acm X biosynthesis. Both acm

  4. A comparison of properties between carboxylated acrylic rubbers prepared by γ-ray irradiation and chemical method

    Wang Weiwei; Chang Zhenqi; Wang Mozhen; Zhang Zhicheng; Lv Pin

    2006-01-01

    Acrylic rubbers (ACM) carboxylated by acrylic acid or itaconic acid were prepared by 60 Co γ-ray or chemical-initiator (K 2 S 2 O 8 ) induced emulsion copolymerization. The polymers were characterized by Fourier transform infrared spectroscopy (FT-IR). Acid value, molecular weight and polydispersity index (PDI) of the polymers were determined by non-aqueous titration method and gel permeation chromatography (GPC), respectively. Vulcanization and mechanical properties of the filled ACM were studied by rheometric measurement, gel fraction analysis, mechanical property tests and dynamic mechanical thermal analysis (DMTA). The results show that the ACMs prepared by γ-ray irradiation have lower acid value, higher molecular weight and narrower PDI than chemically prepared ACMs of the same compositions. The itaconic acid carboxylated ACM has better cure characteristics and mechanical properties than the acrylic acid carboxylated ACM. The itaconic acid carboxylated ACM prepared by γ-ray irradiation has higher gel fraction and better cure characteristics as well as mechanical properties than that prepared by chemical method. (authors)

  5. Nitrogen-doped porous carbon monoliths from polyacrylonitrile (PAN) and carbon nanotubes as electrodes for supercapacitors

    Wang, Yanqing; Fugetsu, Bunshi; Wang, Zhipeng; Gong, Wei; Sakata, Ichiro; Morimoto, Shingo; Hashimoto, Yoshio; Endo, Morinobu; Dresselhaus, Mildred; Terrones, Mauricio

    2017-01-01

    Nitrogen-doped porous activated carbon monoliths (NDP-ACMs) have long been the most desirable materials for supercapacitors. Unique to the conventional template based Lewis acid/base activation methods, herein, we report on a simple yet practicable novel approach to production of the three-dimensional NDP-ACMs (3D-NDP-ACMs). Polyacrylonitrile (PAN) contained carbon nanotubes (CNTs), being pre-dispersed into a tubular level of dispersions, were used as the starting material and the 3D-NDP-ACMs were obtained via a template-free process. First, a continuous mesoporous PAN/CNT based 3D monolith was established by using a template-free temperature-induced phase separation (TTPS). Second, a nitrogen-doped 3D-ACM with a surface area of 613.8 m2/g and a pore volume 0.366 cm3/g was obtained. A typical supercapacitor with our 3D-NDP-ACMs as the functioning electrodes gave a specific capacitance stabilized at 216 F/g even after 3000 cycles, demonstrating the advantageous performance of the PAN/CNT based 3D-NDP-ACMs. PMID:28074847

  6. Acemetacin cocrystal structures by powder X-ray diffraction

    Bolla, Geetha

    2017-01-01

    Cocrystals of acemetacin drug (ACM) with nicotinamide (NAM), p-aminobenzoic acid (PABA), valerolactam (VLM) and 2-pyridone (2HP) were prepared by melt crystallization and their X-ray crystal structures determined by high-resolution powder X-ray diffraction. The powerful technique of structure determination from powder data (SDPD) provided details of molecular packing and hydrogen bonding in pharmaceutical cocrystals of acemetacin. ACM–NAM occurs in anhydrate and hydrate forms, whereas the other structures crystallized in a single crystalline form. The carboxylic acid group of ACM forms theacid–amide dimer three-point synthon R 3 2(9)R 2 2(8)R 3 2(9) with three different syn amides (VLM, 2HP and caprolactam). The conformations of the ACM molecule observed in the crystal structures differ mainly in the mutual orientation of chlorobenzene fragment and the neighboring methyl group, being anti (type I) or syn (type II). ACM hydrate, ACM—NAM, ACM–NAM-hydrate and the piperazine salt of ACM exhibit the type I conformation, whereas ACM polymorphs and other cocrystals adopt the ACM type II conformation. Hydrogen-bond interactions in all the crystal structures were quantified by calculating their molecular electrostatic potential (MEP) surfaces. Hirshfeld surface analysis of the cocrystal surfaces shows that about 50% of the contribution is due to a combination of strong and weak O⋯H, N⋯H, Cl⋯H and C⋯H interactions. The physicochemical properties of these cocrystals are under study. PMID:28512568

  7. Acemetacin cocrystal structures by powder X-ray diffraction

    Geetha Bolla

    2017-05-01

    Full Text Available Cocrystals of acemetacin drug (ACM with nicotinamide (NAM, p-aminobenzoic acid (PABA, valerolactam (VLM and 2-pyridone (2HP were prepared by melt crystallization and their X-ray crystal structures determined by high-resolution powder X-ray diffraction. The powerful technique of structure determination from powder data (SDPD provided details of molecular packing and hydrogen bonding in pharmaceutical cocrystals of acemetacin. ACM–NAM occurs in anhydrate and hydrate forms, whereas the other structures crystallized in a single crystalline form. The carboxylic acid group of ACM forms theacid–amide dimer three-point synthon R32(9R22(8R32(9 with three different syn amides (VLM, 2HP and caprolactam. The conformations of the ACM molecule observed in the crystal structures differ mainly in the mutual orientation of chlorobenzene fragment and the neighboring methyl group, being anti (type I or syn (type II. ACM hydrate, ACM—NAM, ACM–NAM-hydrate and the piperazine salt of ACM exhibit the type I conformation, whereas ACM polymorphs and other cocrystals adopt the ACM type II conformation. Hydrogen-bond interactions in all the crystal structures were quantified by calculating their molecular electrostatic potential (MEP surfaces. Hirshfeld surface analysis of the cocrystal surfaces shows that about 50% of the contribution is due to a combination of strong and weak O...H, N...H, Cl...H and C...H interactions. The physicochemical properties of these cocrystals are under study.

  8. Nitrogen-doped porous carbon monoliths from polyacrylonitrile (PAN) and carbon nanotubes as electrodes for supercapacitors.

    Wang, Yanqing; Fugetsu, Bunshi; Wang, Zhipeng; Gong, Wei; Sakata, Ichiro; Morimoto, Shingo; Hashimoto, Yoshio; Endo, Morinobu; Dresselhaus, Mildred; Terrones, Mauricio

    2017-01-11

    Nitrogen-doped porous activated carbon monoliths (NDP-ACMs) have long been the most desirable materials for supercapacitors. Unique to the conventional template based Lewis acid/base activation methods, herein, we report on a simple yet practicable novel approach to production of the three-dimensional NDP-ACMs (3D-NDP-ACMs). Polyacrylonitrile (PAN) contained carbon nanotubes (CNTs), being pre-dispersed into a tubular level of dispersions, were used as the starting material and the 3D-NDP-ACMs were obtained via a template-free process. First, a continuous mesoporous PAN/CNT based 3D monolith was established by using a template-free temperature-induced phase separation (TTPS). Second, a nitrogen-doped 3D-ACM with a surface area of 613.8 m 2 /g and a pore volume 0.366 cm 3 /g was obtained. A typical supercapacitor with our 3D-NDP-ACMs as the functioning electrodes gave a specific capacitance stabilized at 216 F/g even after 3000 cycles, demonstrating the advantageous performance of the PAN/CNT based 3D-NDP-ACMs.

  9. Effect of carbonization temperature on the physical and electrochemical properties of supercapacitor electrode from fibers of oil palm empty fruit bunches

    Ishak, M. M.; Deraman, M., E-mail: madra@ukm.my; Talib, I. A.; Basri, N. H.; Omar, R.; Nor, N. S. M.; Dolah, B. N. M. [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Awitdrus,; Farma, R.; Taer, E. [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Department of Physics, Faculty of Mathematics and Natural Sciences, University of Riau, 28293 Pekanbaru, Riau (Indonesia)

    2015-04-16

    Self-adhesive carbon grains (SACG) was prepared from fibers of oil palm empty fruit bunches. The SACG green monoliths were carbonized in N{sub 2} environment at 400, 500, 600 and 700°C to produce carbon monoliths labeled as CM1, CM2, CM3 and CM4 respectively. The CMs were activated in CO{sub 2} surrounding at 800°C for 1 hour to produce activated carbon monolith electrodes (ACM1, ACM2, ACM3 and ACM4). The physical properties of the CMs and ACMs were investigated using X-ray diffraction, field emission scanning electron microscopy (FESEM) and N{sub 2} adsorption-desorption isotherm techniques. ACMs were used as electrode to fabricate symmetry supercapacitor cells and the cells’ performances were investigated using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) standard techniques. In this paper we report the physical and electrochemical properties of the ACM electrodes by analyzing the influence of the carbonization temperature on these properties.

  10. Effect of carbonization temperature on the physical and electrochemical properties of supercapacitor electrode from fibers of oil palm empty fruit bunches

    Ishak, M. M.; Deraman, M.; Talib, I. A.; Basri, N. H.; Omar, R.; Nor, N. S. M.; Dolah, B. N. M.; Awitdrus,; Farma, R.; Taer, E.

    2015-01-01

    Self-adhesive carbon grains (SACG) was prepared from fibers of oil palm empty fruit bunches. The SACG green monoliths were carbonized in N 2 environment at 400, 500, 600 and 700°C to produce carbon monoliths labeled as CM1, CM2, CM3 and CM4 respectively. The CMs were activated in CO 2 surrounding at 800°C for 1 hour to produce activated carbon monolith electrodes (ACM1, ACM2, ACM3 and ACM4). The physical properties of the CMs and ACMs were investigated using X-ray diffraction, field emission scanning electron microscopy (FESEM) and N 2 adsorption-desorption isotherm techniques. ACMs were used as electrode to fabricate symmetry supercapacitor cells and the cells’ performances were investigated using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) standard techniques. In this paper we report the physical and electrochemical properties of the ACM electrodes by analyzing the influence of the carbonization temperature on these properties

  11. Optimization of Life Cycle Extension of Asphalt Concrete Mixtures in regard to Material Properties, Structural Design, and Economic Implications

    Jan Mikolaj

    2016-01-01

    Full Text Available Design of ACM life cycle is defined with respect to traffic load acting on the pavement and road class for a period of about 20 years. In practice, reconstruction is usually pending until the end of the life cycle after which the reconstruction takes place and the original materials are replaced by new materials. Life cycle of the pavement construction in road structure is significantly longer than that of the ACM; it is therefore necessary to consider ACM from a long term viewpoint, that is, exceeding their life expectancy. This paper describes a methodology which consists of analytical calculations, experimental measurements, and optimization of the ACM life cycle with the use of a rehabilitation action to provide new physical properties of pavement surfacing in different periods of the original life cycle. The aim is to attain maximal economic effectiveness, by minimizing financial costs for rehabilitation and maintenance and economic costs of road user. Presented method allows deriving optimal life cycle from various rehabilitation alternatives for particular ACM with the fact that all the necessary parameters are derived from specific experimental measurements and calculations. The method is applicable to all types of ACM materials; however, for each material, it is necessary to carry out the necessary measurements and tests. The article describes the methodology and case study results for a particular type of ACM material.

  12. Genetic Etiology for Alcohol-Induced Cardiac Toxicity.

    Ware, James S; Amor-Salamanca, Almudena; Tayal, Upasana; Govind, Risha; Serrano, Isabel; Salazar-Mendiguchía, Joel; García-Pinilla, Jose Manuel; Pascual-Figal, Domingo A; Nuñez, Julio; Guzzo-Merello, Gonzalo; Gonzalez-Vioque, Emiliano; Bardaji, Alfredo; Manito, Nicolas; López-Garrido, Miguel A; Padron-Barthe, Laura; Edwards, Elizabeth; Whiffin, Nicola; Walsh, Roddy; Buchan, Rachel J; Midwinter, William; Wilk, Alicja; Prasad, Sanjay; Pantazis, Antonis; Baski, John; O'Regan, Declan P; Alonso-Pulpon, Luis; Cook, Stuart A; Lara-Pezzi, Enrique; Barton, Paul J; Garcia-Pavia, Pablo

    2018-05-22

    Alcoholic cardiomyopathy (ACM) is defined by a dilated and impaired left ventricle due to chronic excess alcohol consumption. It is largely unknown which factors determine cardiac toxicity on exposure to alcohol. This study sought to evaluate the role of variation in cardiomyopathy-associated genes in the pathophysiology of ACM, and to examine the effects of alcohol intake and genotype on dilated cardiomyopathy (DCM) severity. The authors characterized 141 ACM cases, 716 DCM cases, and 445 healthy volunteers. The authors compared the prevalence of rare, protein-altering variants in 9 genes associated with inherited DCM. They evaluated the effect of genotype and alcohol consumption on phenotype in DCM. Variants in well-characterized DCM-causing genes were more prevalent in patients with ACM than control subjects (13.5% vs. 2.9%; p = 1.2 ×10 -5 ), but similar between patients with ACM and DCM (19.4%; p = 0.12) and with a predominant burden of titin truncating variants (TTNtv) (9.9%). Separately, we identified an interaction between TTN genotype and excess alcohol consumption in a cohort of DCM patients not meeting ACM criteria. On multivariate analysis, DCM patients with a TTNtv who consumed excess alcohol had an 8.7% absolute reduction in ejection fraction (95% confidence interval: -2.3% to -15.1%; p ACM patients. TTNtv represent a prevalent genetic predisposition for ACM, and are also associated with a worse left ventricular ejection fraction in DCM patients who consume alcohol above recommended levels. Familial evaluation and genetic testing should be considered in patients presenting with ACM. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

  13. Testing Mediators of Reduced Drinking for Veterans in Alcohol Care Management.

    Moskal, Dezarie; Maisto, Stephen A; Possemato, Kyle; Lynch, Kevin G; Oslin, David W

    2018-03-26

    Alcohol Care Management (ACM) is a manualized treatment provided by behavioral health providers working in a primary care team aimed at increasing patients' treatment engagement and decreasing their alcohol use. Research has shown that ACM is effective in reducing alcohol consumption; however, the mechanisms of ACM are unknown. Therefore, the purpose of this study is to examine the mechanisms of change in ACM in the context of a randomized clinical trial evaluating the effectiveness of ACM. This study performed secondary data analysis of existing data from a larger study that involved a sample of U.S. veterans (N = 163) who met criteria for current alcohol dependence. Upon enrollment into the study, participants were randomized to receive either ACM or standard care. ACM was delivered in-person or by telephone within the primary care clinic and focused on the use of oral naltrexone and manualized psychosocial support. According to theory, we hypothesized several ACM treatment components that would mediate alcohol consumption outcomes: engagement in addiction treatment, reduced craving, and increased readiness to change. Parallel mediation models were performed by the PROCESS macro Model 4 in SPSS to test study hypotheses. The institutional review boards at each of the participating facilities approved all study procedures before data collection. As hypothesized, results showed that treatment engagement mediated the relation between treatment and both measures of alcohol consumption outcomes, the percentage of alcohol abstinent days, and the percentage of heavy drinking days. Neither craving nor readiness to change mediated the treatment effect on either alcohol consumption outcome. Findings suggest that ACM may be effective in changing drinking patterns partially due to an increase in treatment engagement. Future research may benefit from evaluating the specific factors that underlie increased treatment engagement. The current study provides evidence that alcohol

  14. National, regional and global mortality due to alcoholic cardiomyopathy in 2015.

    Manthey, Jakob; Probst, Charlotte; Rylett, Margaret; Rehm, Jürgen

    2018-03-13

    (1) A comprehensive mortality assessment of alcoholic cardiomyopathy (ACM) and (2) examination of under-reporting using vital statistics data. A modelling study estimated sex-specific mortality rates for each country, which were subsequently aggregated by region and globally. Input data on ACM mortality were obtained from death registries for n=91 countries. For n=99 countries, mortality estimates were predicted using aggregate alcohol data from WHO publications. Descriptive additional analyses illustrated the scope of under-reporting. In 2015, there were an estimated 25 997 (95% CI 17 385 to 49 096) global deaths from ACM. This translates into 6.3% (95% CI 4.2% to 11.9%) of all global deaths from cardiomyopathy being caused by alcohol. There were large regional variations with regard to mortality burden. While the majority of ACM deaths were found in Russia (19 749 deaths, 76.0% of all ACM deaths), for about one-third of countries (n=57) less than one ACM death was found. Under-reporting was identified for nearly every second country with civil registration data. Overall, two out of three global ACM deaths might be misclassified. The variation of ACM mortality burden is greater than for other alcohol-attributable diseases, and partly may be the result of stigma and lack of detection. Misclassification of ACM fatalities is a systematic phenomenon, which may be caused by low resources, lacking standards and stigma associated with alcohol-use disorders. Clinical management may be improved by including routine alcohol assessments. This could contribute to decrease misclassifications and to provide the best available treatment for affected patients. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  15. Optimal arrangement of magnetic coils for functional magnetic stimulation of the inspiratory muscles in dogs.

    Lin, Vernon Weh-Hau; Zhu, Ercheng; Sasse, Scott A; Sassoon, Catherine; Hsiao, Ian N

    2005-12-01

    In an attempt to maximize inspiratory pressure and volume, the optimal position of a single or of dual magnetic coils during functional magnetic stimulation (FMS) of the inspiratory muscles was evaluated in twenty-three dogs. Unilateral phrenic magnetic stimulation (UPMS) or bilateral phrenic magnetic stimulation (BPMS), posterior cervical magnetic stimulation (PCMS), anterior cervical magnetic stimulation (ACMS) as well as a combination of PCMS and ACMS were performed. Trans-diaphragmatic pressure (Pdi), flow, and lung volume changes with an open airway were measured. Transdiaphragmatic pressure was also measured with an occluded airway. Changes in inspiratory parameters during FMS were compared with 1) electrical stimulation of surgically exposed bilateral phrenic nerves (BPES) and 2) ventral root electrical stimulation at C5-C7 (VRES C5-C7). Relative to the Pdi generated by BPES of 36.3 +/- 4.5 cm H2O (Mean +/- SEM), occluded Pdi(s) produced by UPMS, BPMS, PCMS, ACMS, and a combined PCMS + ACMS were 51.7%, 61.5%, 22.4%, 100.3%, and 104.5% of the maximal Pdi, respectively. Pdi(s) produced by UPMS, BPMS, PCMS, ACMS, and combined ACMS + PCMS were 38.0%, 45.2%, 16.5%, 73.8%, and 76.8%, respectively, of the Pdi induced by VRES (C5-C7) (48.0 +/- 3.9 cm H2O). The maximal Pdi(s) generated during ACMS and combined PCMS + ACMS were higher than the maximal Pdi(s) generated during UPMS, BPMS, or PCMS (p BPMS or PCMS. ACMS can be used to generate sufficient inspiratory pressure, flow, and volume for activation of the inspiratory muscles.

  16. Satellite Media Broadcasting with Adaptive Coding and Modulation

    Georgios Gardikis

    2009-01-01

    Full Text Available Adaptive Coding and Modulation (ACM is a feature incorporated into the DVB-S2 satellite specification, allowing real-time adaptation of transmission parameters according to the link conditions. Although ACM was originally designed for optimizing unicast services, this article discusses the expansion of its usage to broadcasting streams as well. For this purpose, a general cross-layer adaptation approach is proposed, along with its realization into a fully functional experimental network, and test results are presented. Finally, two case studies are analysed, assessing the gain derived by ACM in a real large-scale deployment, involving HD services provision to two different geographical areas.

  17. Framework for developing realistic MANET simulations

    Burke, ID

    2010-04-01

    Full Text Available : Proceedings of the second ACM international workshop on Principles of mobile computing. Toulouse, France, 2002. ACM. Chin, K.-W., Judge, J., Williams, A. & Kermode, R., 2002. Implementation experience with MANET routing protocols. SIGCOMM Comput. Commun... & computing. Long Beach, CA, USA, 2001. ACM. Fall, K. & Varadhan, K., 2003. NS-Manual. [PDF] Available at: http://www.isi.edu/nsnam/ns/doc/ns_doc.pdf . Garrido, P.P., Malumbres, M.P. & Calafate, C.T., 2008. ns-2 vs. OPNET: a comparative study of the IEEE...

  18. Sulfidization of an aluminocobaltomolybdenum catalyst using the 35S radioisotope

    Isagulyants, G.V.; Greish, A.A.; Kogan, V.M.

    1987-01-01

    It has been established that in aluminocobaltomolybdenum catalyst sulfidized with elemental sulfur there are two types of sulfur, free and bound. The maximum amount of bound sulfur in ACM catalyst is 6.6 wt. %, which corresponds to practically complete sulfidation of the ACM catalyst. In the presence of hydrogen an equilibrium distribution of bound sulfur is achieved in a granule of ACM catalyst irrespective of the temperature of sulfidation. In a nitrogen atmosphere it is primarily the surface layers of the catalyst that are sulfured

  19. Cerebral and spinal MR-findings in patients with postrepair myelomeningocele

    Just, M.; Thelen, M.; Ludwig, B.

    1990-01-01

    In 114 patients with postrepair myelomeningocele MRI of the spine was performed. Tethered cord (89%) and associated malformations (syrinx, lipoma etc.) (33%) were the most important findings. Additional MRI scans of the head (44 patients) revealed numerous further anomalies. Arnold Chiari malformation was found in 76% of the patients (ACM I: 32%, ACM II: 44%). In the ACM II group compression of lower cranial nerves, brain stem, and cerebellum can lead to considerable neurologic symptoms. Therefore in patients with progressive neurologic dysfunction a complete investigation of the whole spine and brain is necessary. MRI proves to be the diagnostic procedure of choice in patients with dysraphic myelodysplasia. (orig.)

  20. Microstructure and Mechanical Properties of Porous Mullite

    Hsiung, Chwan-Hai Harold

    Mullite (3 Al2O3 : 2 SiO2) is a technologically important ceramic due to its thermal stability, corrosion resistance, and mechanical robustness. One variant, porous acicular mullite (ACM), has a unique needle-like microstructure and is the material platform for The Dow Chemical Company's diesel particulate filter AERIFY(TM). The investigation described herein focuses on the microstructure-mechanical property relationships in acicular mullites as well as those with traditional porous microstructures with the goal of illuminating the critical factors in determining their modulus, strength, and toughness. Mullites with traditional pore morphologies were made to serve as references via slipcasting of a kaolinite-alumina-starch slurry. The starch was burned out to leave behind a pore network, and the calcined body was then reaction-sintered at 1600C to form mullite. The samples had porosities of approximately 60%. Pore size and shape were altered by using different starch templates, and pore size was found to influence the stiffness and toughness. The ACM microstructure was varied along three parameters: total porosity, pore size, and needle size. Total porosity was found to dominate the mechanical behavior of ACM, while increases in needle and pore size increased the toughness at lower porosities. ACM was found to have much improved (˜130%) mechanical properties relative to its non-acicular counterpart at the same porosity. A second set of investigations studied the role of the intergranular glassy phase which wets the needle intersections of ACM. Removal of the glassy phase via an HF etch reduced the mechanical properties by ˜30%, highlighting the intergranular phase's importance to the enhanced mechanical properties of ACM. The composition of the glassy phase was altered by doping the ACM precursor with magnesium and neodymium. Magnesium doping resulted in ACM with greatly reduced fracture strength and toughness. Studies showed that the mechanical properties of the

  1. Fulltext PDF

    applications such as 3D graphics, interactive video games, speech processing ... ran a wide range of applications that included video and ..... reaping great performance benefits. Figure 6 gives the flow .... Communications o/the ACM. VoL40.

  2. Learning from Learning: the experiences with implementing Adaptive Collaborative Forest Management in Zimbabwe.

    Mutimukuru, T.; Almekinders, C.J.M.

    2011-01-01

    Convinced that participatory resource management is the way forward in the conservation of natural resources, despite the increasing criticism of participatory approaches, the Centre for International Forestry Research (CIFOR) initiated a multi-country adaptive collaborative management (ACM)

  3. Serial fetal abdominal circumference measurements in predicting normal birth weight in gestational diabetes mellitus.

    Neff, Karl J

    2013-06-24

    To construct a clinical management matrix using serial fetal abdominal circumference measurements (ACMs) that will predict normal birth weight in pregnancies complicated by gestational diabetes (GDM) and reduce unnecessary ultrasound examination in women with GDM.

  4. 40 CFR 763.80 - Scope and purpose.

    2010-07-01

    ..., sampling such materials if they are not assumed to be ACM, and having samples analyzed by appropriate... disposal of asbestos in accordance with EPA's “Asbestos Waste Management Guidance.” For convenience...

  5. Automated Contingency Management for Advanced Propulsion Systems, Phase II

    National Aeronautics and Space Administration — Automated Contingency Management (ACM), or the ability to confidently and autonomously adapt to fault conditions with the goal of still achieving mission objectives,...

  6. An improved predictive association rule based classifier using gain ...

    of the customer and the relationship among market–basket items are uncovered ... CAR's discover the inter-relationship between the disease symptoms that are useful for disease ...... Management, Maui, Hawaii, USA: ACM,USA; 1482–1486.

  7. High current density M-type cathodes for vacuum electron devices

    Li Ji; Yu Zhiqiang; Shao Wensheng; Zhang Ke; Gao Yujuan; Yuan Haiqing; Wang Hui; Huang Kaizhi; Chen Qilue; Yan Suqiu; Cai Shaolun

    2005-01-01

    We investigated high current density emission capabilities of M-type cathodes used for vacuum electron devices (VEDs). The experimental results of emission and lifetime evaluating in both close-spaced diode structure and electron gun testing vehicles are given. Emission current densities measured in the diode structure at 1020 deg. C Br in the CW mode were above 10 A/cm 2 ; while in electron gun testing vehicles, emission current densities were above 8 A/cm 2 in CW mode and above 32 A/cm 2 in pulsed mode, respectively. The current density above 94 A/cm 2 has been acquired in no. 0306 electron gun vehicle while the practical temperature is 1060 deg. C Br . For a comparison some of the data from I-scandate cathodes are presented. Finally, several application examples in practical travelling wave tubes (TWTs) and multi beam klystrons (MBKs) are also reported

  8. Modelling discontinuous well log signal to identify lithological ...

    1Indian School of Mines (ISM), Dhanbad 826 004, India. ... new wavelet transform-based algorithm to model the abrupt discontinuous changes from well log data by taking care of ...... the 11th ACM International Conference on Multimedia,.

  9. Prognostics in the Control Loop

    National Aeronautics and Space Administration — The term Automated Contingency Management (ACM) has been used to describe intelligent systems capable of mission re-planning and control reconfiguration in the...

  10. The influence of acoustic emissions for underwater data transmission on the behaviour of harbour porpoises (Phocoena phocoena) in a floating pen

    Kastelein, R.A.; Verboom, W.C.; Muijsers, M.; Jennings, N.V.; Heul, S. van der

    2005-01-01

    To prevent grounding of ships and collisions between ships in shallow coastal waters, an underwater data collection and communication network is currently under development: Acoustic Communication network for Monitoring of underwater Environment in coastal areas (ACME). Marine mammals might be

  11. Semantic intrusion detection with multisensor data fusion using ...

    spatiotemporal relations to form complex events which model the intrusion patterns. ... Wireless sensor networks; complex event processing; event stream; ...... of the 2006 ACM SIGMOD International Conference on Management of Data, 407– ...

  12. Participation of the arcRACME protein in self-activation of the arc operon located in the arginine catabolism mobile element in pandemic clone USA300.

    Rozo, Zayda Lorena Corredor; Márquez-Ortiz, Ricaurte Alejandro; Castro, Betsy Esperanza; Gómez, Natasha Vanegas; Escobar-Pérez, Javier

    2017-07-01

    Staphylococcus aureus pandemic clone USA300 has, in addition to its constitutive arginine catabolism (arc) gene cluster, an arginine catabolism mobile element (ACME) carrying another such cluster, which gives this clone advantages in colonisation and infection. Gene arcR, which encodes an oxygen-sensitive transcriptional regulator, is inside ACME and downstream of the constitutive arc gene cluster, and this situation may have an impact on its activation. Different relative expression behaviours are proven here for arcRACME and the arcACME operon compared to the constitutive ones. We also show that the artificially expressed recombinant ArcRACME protein binds to the promoter region of the arcACME operon; this mechanism can be related to a positive feedback model, which may be responsible for increased anaerobic survival of the USA300 clone during infection-related processes.

  13. WWW History Exhibition LEPFest 2000

    2000-01-01

    1990 NeXT browser, editor, server 1991 Line Mode Browser 1992 HEP servers 1993 CERN software is put in public domain 1994 First Conference 1994 Founding of Consortium 1995 Transfer to INRIA - ACM Award

  14. Efficient operation scheduling for adsorption chillers using predictive optimization-based control methods

    Bürger, Adrian; Sawant, Parantapa; Bohlayer, Markus; Altmann-Dieses, Angelika; Braun, Marco; Diehl, Moritz

    2017-10-01

    Within this work, the benefits of using predictive control methods for the operation of Adsorption Cooling Machines (ACMs) are shown on a simulation study. Since the internal control decisions of series-manufactured ACMs often cannot be influenced, the work focuses on optimized scheduling of an ACM considering its internal functioning as well as forecasts for load and driving energy occurrence. For illustration, an assumed solar thermal climate system is introduced and a system model suitable for use within gradient-based optimization methods is developed. The results of a system simulation using a conventional scheme for ACM scheduling are compared to the results of a predictive, optimization-based scheduling approach for the same exemplary scenario of load and driving energy occurrence. The benefits of the latter approach are shown and future actions for application of these methods for system control are addressed.

  15. Mapping Emplaced Articulated Concrete Mattress Using Geoelectrical and Electromagnetic Techniques

    Sjostrom, Keith

    1998-01-01

    Articulated concrete mattresses (ACM) are structures placed parallel to the river current for the purpose of stabilizing the concave banks in river bends, reduce the effects of erosion, and maintain the river channel...

  16. Huffman-based code compression techniques for embedded processors

    Bonny, Mohamed Talal; Henkel, Jö rg

    2010-01-01

    % for ARM and MIPS, respectively. In our compression technique, we have conducted evaluations using a representative set of applications and we have applied each technique to two major embedded processor architectures, namely ARM and MIPS. © 2010 ACM.

  17. Design of Operation Parameters to Resolve Two Targets using Proximity Sensors

    2010-07-01

    network,” in MOBIHOC, EPF Lausanne, Switzerland, 2002. [12] V. Cevher and L. Kaplan, “Acoustic sensor net- work design for position estimation,” ACM Trans- actions on Sensor Networks, vol. 4, 2009.

  18. Security of statistical data bases: invasion of privacy through attribute correlational modeling

    Palley, M.A.

    1985-01-01

    This study develops, defines, and applies a statistical technique for the compromise of confidential information in a statistical data base. Attribute Correlational Modeling (ACM) recognizes that the information contained in a statistical data base represents real world statistical phenomena. As such, ACM assumes correlational behavior among the database attributes. ACM proceeds to compromise confidential information through creation of a regression model, where the confidential attribute is treated as the dependent variable. The typical statistical data base may preclude the direct application of regression. In this scenario, the research introduces the notion of a synthetic data base, created through legitimate queries of the actual data base, and through proportional random variation of responses to these queries. The synthetic data base is constructed to resemble the actual data base as closely as possible in a statistical sense. ACM then applies regression analysis to the synthetic data base, and utilizes the derived model to estimate confidential information in the actual database.

  19. Electrically Injected Polariton Lasing from a GaAs-Based Microcavity under Magnetic Field

    Bhattacharya, Pallab; Das, Ayan; Jankowski, Marc; Bhowmick, Sishir; Lee, Chi-Sen; Jahangir, Shafat

    2012-01-01

    Suppression of relaxation bottleneck and subsequent polariton lasing is observed in a GaAs-based microcavity under the application of a magnetic field. The threshold injection current density is 0.32 A/cm2 at 7 Tesla.

  20. Molecular Characterization of Methicillin-Resistant Staphylococcus aureus from Outpatients in Northern Japan: Increasing Tendency of ST5/ST764 MRSA-IIa with Arginine Catabolic Mobile Element.

    Aung, Meiji Soe; Kawaguchiya, Mitsuyo; Urushibara, Noriko; Sumi, Ayako; Ito, Masahiko; Kudo, Kenji; Morimoto, Shigeo; Hosoya, Shino; Kobayashi, Nobumichi

    2017-07-01

    Arginine catabolic mobile element (ACME) is a genomic island of staphylococcus and is considered to confer enhanced ability to survive and growth on host bacterial cells. ACME has been typically identified in Panton-Valentine Leukocidin (PVL)-positive ST8 methicillin-resistant Staphylococcus aureus (MRSA) with SCCmec type IVa (USA300 clone), and it is also found in other lineages at low frequency. Prevalence and molecular characteristics of PVL + and/or ACME + MRSA were investigated for 624 clinical isolates collected from outpatients in northern Japan from 2013 to 2014. Both PVL genes and ACME type I were detected in nine isolates (1.4%), which were ST8-MRSA-SCCmec IVa/spa type t008/agr-I; whereas solely PVL genes were positive in two isolates, ST30-MRSA-SCCmec IV and ST59-MRSA-SCCmec V. ACME type II' (previously referred to as ACME ΔII) was detected in 36 isolates (5.8%) with SCCmec II and V (32 and 4 isolates, respectively), exhibiting an increased rate within SCCmec II-MRSA (7.1%) compared with our previous studies (0.86-4.5%, 2008-2011). ACME II'-positive MRSA strains were classified into ST5-SCCmec IIa/V or ST764-SCCmec IIa belonging to five different spa types, with t002 being dominant. They harbored mostly enterotoxin gene clusters (seg-sei-sem-sen-seo-seu) and some more enterotoxin genes (seb1, seb2, sec3, sel, sep), showing resistance to more antimicrobials than ST8-MRSA-SCCmec IVa. ACME-SCCmec composite island (CI) of the 36 ACME II'-positive MRSA was classified into five types (ii)-(vi), among which type (ii) (orfX-ΨSCC ΔJ1 SCCmec I -ACME II'-SCCmec II) was dominant and subdivided into the A3 variant and the less common A2 variant. CI types (v) and (vi) were considered novel genetic organizations having speG (acetyltransferase genes for polyamines) in inserted SCC4610/SCC266-like genetic elements. The present study revealed increased prevalence and genetic diversity of the ST5/ST764-MRSA-SCCmec II with ACME II' in northern Japan.

  1. A Model of Onion Routing With Provable Anonymity

    2006-08-30

    Lysyanskaya. “A Formal Treatment of Onion Routing.” CRYPTO 2005, pp. 169.187, 2005. [4] David Chaum . “The dining cryptographers problem...1988. [5] David Chaum . “Untraceable Electronic Mail, Return Addresses, and Digital Pseudonyms.” Communi- cations of the ACM, 24(2), pp. 84-88, 1981...network layer.” ACM Conference on Computer and Communications Security, pp. 193-206, 2002. [11] David Goldschlag, Michael Reed, and Paul Syverson

  2. Finite element modelling of vocal tract changes after voice therapy

    Vampola, T.; Laukkanen, A. M.; Horáček, Jaromír; Švec, J. G.

    2011-01-01

    Roč. 5, č. 1 (2011), s. 77-88 ISSN 1802-680X R&D Projects: GA ČR GA101/08/1155 Institutional research plan: CEZ:AV0Z20760514 Keywords : biomechanics of human voice * voice production modelling * vocal excersing * voice training Subject RIV: BI - Acoustics http://www.kme.zcu.cz/acm/index.php/acm/article/view/138

  3. Do Adaptive Comanagement Processes Lead to Adaptive Comanagement Outcomes? A Multicase Study of Long-term Outcomes Associated with the National Riparian Service Team's Place-based Riparian Assistance

    Jill A. Smedstad

    2013-12-01

    Full Text Available Adaptive comanagement (ACM is a novel approach to environmental governance that combines the dynamic learning features of adaptive management with the linking and network features of collaborative management. There is growing interest in the potential for ACM to resolve conflicts around natural resource management and contribute to greater social and ecological resilience, but little is known about how to catalyze long lasting ACM arrangements. We contribute to knowledge on this topic by evaluating the National Riparian Service Team's (NRST efforts to catalyze ACM of public lands riparian areas in seven cases in the western U.S. We found that the NRST's approach offers a relatively novel model for integrating joint fact-finding, multiple forms of knowledge, and collaborative problem solving to improve public lands riparian grazing management. With this approach, learning and dialogue often helped facilitate the development of shared understanding and trust, key features of ACM. Their activities also influenced changes in assessment, monitoring, and management approaches to public lands riparian area grazing, also indicative of a transition to ACM. Whereas these effects often aligned with the NRST's immediate objectives, i.e., to work through a specific issue or point of conflict, there was little evidence of long-term effects beyond the specific issue or intervention; that is, in most cases the initiative did not influence longer term changes in place-based governance and institutions. Our results suggest that the success of interventions aimed at catalyzing the transformation of governance arrangements toward ACM may hinge on factors external to the collaborative process such as the presence or absence of (1 dynamic local leadership and (2 high quality agreements regarding next steps for the group. Efforts to establish long lasting ACM institutions may also face significant constraints and barriers, including existing laws and regulations

  4. Theoretical and experimental analysis of amplitude control ablation and bipolar ablation in creating linear lesion and discrete lesions for treating atrial fibrillation.

    Yan, Shengjie; Wu, Xiaomei; Wang, Weiqi

    2017-09-01

    Radiofrequency (RF) energy is often used to create a linear lesion or discrete lesions for blocking the accessory conduction pathways for treating atrial fibrillation. By using finite element analysis, we study the ablation effect of amplitude control ablation mode (AcM) and bipolar ablation mode (BiM) in creating a linear lesion and discrete lesions in a 5-mm-thick atrial wall; particularly, the characteristic of lesion shape has been investigated in amplitude control ablation. Computer models of multipolar catheter were developed to study the lesion dimensions in atrial walls created through AcM, BiM and special electrodes activated ablation methods in AcM and BiM. To validate the theoretical results in this study, an in vitro experiment with porcine cardiac tissue was performed. At 40 V/20 V root mean squared (RMS) of the RF voltage for AcM, the continuous and transmural lesion was created by AcM-15s, AcM-5s and AcM-ad-20V ablation in 5-mm-thick atrial wall. At 20 V RMS for BiM, the continuous but not transmural lesion was created. AcM ablation yielded asymmetrical and discrete lesions shape, whereas the lesion shape turned to more symmetrical and continuous as the electrodes alternative activated period decreased from 15 s to 5 s. Two discrete lesions were created when using AcM, AcM-ad-40V, BiM-ad-20V and BiM-ad-40V. The experimental and computational thermal lesion shapes created in cardiac tissue were in agreement. Amplitude control ablation technology and bipolar ablation technology are feasible methods to create continuous lesion or discrete for pulmonary veins isolation.

  5. Mineralogical conversion of asbestos containing materials

    Pulsford, S.K.; Foltz, A.D.; Ek, R.B.

    1996-01-01

    The principal objective of the Technical Task Plan (TTP) is to demonstrate a thermal-chemical mineralogical asbestos conversion unit at the Hanford Site, which converts non-radiological asbestos containing materials (ACMs) into an asbestos-free material. The permanent thermal-chemical mineralogical conversion of ACMs to a non-toxic, non-hazardous, potentially marketable end product should not only significantly reduce the waste stream volumes but terminate the open-quotes cradle to graveclose quotes ownership liabilities

  6. Ductile–brittle behavior at blunted cavities in 3D iron crystals uncovered and covered by copper atoms

    Pelikán, Vladimír; Hora, Petr; Červená, Olga; Spielmannová, Alena; Machová, Anna

    2010-01-01

    Roč. 4, č. 2 (2010), s. 191-200 ISSN 1802-680X R&D Projects: GA ČR(CZ) GA101/07/0789; GA AV ČR KJB200760802 Institutional research plan: CEZ:AV0Z20760514 Keywords : molecular dynamics * bcc iron crystal * blunted cavity * copper cover * ductile –brittle behavior Subject RIV: JG - Metallurgy http://www.kme.zcu.cz/acm/index.php/acm/article/view/48

  7. DESPIC: Detecting Early Signatures of Persuasion in Information Cascades

    2015-08-27

    Rio de Janeiro , Brazil. ACM 2013...on   World   Wide   Web  companion,  pp.  1351-­‐1358,  May  13–17,  2013,   Rio   de   Janeiro ,  Brazil.  ACM  2013... de   facto   text   indexing   technology   in   industry.   Thanks   to   the   customized   index   structures,  

  8. Automatic Performance Evaluation for Video Summarization

    2004-07-01

    Multimedia 2002, pp.189–198. [14] S. Uchihashi, J. Foote, A. Girgensohn and J. Boreczky, “Video Manga : Generating Seman- tically Meaningful Video...DeMenthon, V. Kobla and D. Doermann, “Video Summarization by Curve Simplification”, ACM Multimedia 98, Bristol, England, pp. 211-218, September 1998. 26 [2...J. Au, “Video Keyframe Production by Efficient Clustering of Compressed Chromaticity Signatures”, ACM Multimedia 2000, Juan-Les-Pins, France, pp. 365

  9. Teaching to Tinker

    Cermak-Sassenrath, Daniel; Mollenbach, Emilie

    2015-01-01

    Daniel Cermak-Sassenrath, Emilie Mølllenbach. Teaching to Tinker - Making as an Educational Strategy. Workshop description. In: Proceedings of NordiCHI 2014: Fun, Fast, Foundational. New York: ACM, forthcoming.......Daniel Cermak-Sassenrath, Emilie Mølllenbach. Teaching to Tinker - Making as an Educational Strategy. Workshop description. In: Proceedings of NordiCHI 2014: Fun, Fast, Foundational. New York: ACM, forthcoming....

  10. Dynamics of beam pair coupled by visco-elastic interlayer

    Náprstek, Jiří; Hračov, Stanislav

    2015-01-01

    Roč. 9, č. 2 (2015), s. 127-140 ISSN 1802-680X R&D Projects: GA ČR(CZ) GP13-41574P; GA ČR(CZ) GA15-01035S Institutional support: RVO:68378297 Keywords : double-beam dynamics * visco-elastic interlayer * kinematic damping Subject RIV: JM - Building Engineering http://www.kme.zcu.cz/acm/acm/article/view/292

  11. The anaemia control model: Does it help nephrologists in therapeutic decision-making in the management of anaemia?

    Bucalo, María Laura; Barbieri, Carlo; Roca, Susana; Ion Titapiccolo, Jasmine; Ros Romero, Maria Soledad; Ramos, Rosa; Albaladejo, Mercedes; Manzano, Diana; Mari, Flavio; Molina, Manuel

    2018-06-03

    Anaemia is common in haemodialysis patients and treating it with erythropoiesis-stimulating agents (ESAs) is complex due to many factors. To assess the usefulness of the Anaemia Control Model (ACM) in the treatment of anaemia in haemodialysis. ACM is a software that predicts the optimal dose of darbepoetin and iron sucrose to achieve target haemoglobin (Hb) and ferritin levels, and makes prescription suggestions. Study conducted in dialysis clinics lasting 18months with two intervention phases (IPs) with ACM (IP1, n:213; IP2, n:218) separated by a control phase (CP, n:219). The primary outcome was the percentage of Hb in range and the median dose of ESAs, and the secondary outcomes were transfusion, hospitalisation and cardiovascular events. Clinical and patient analyses were performed. Hb variability was assessed by the standard deviation (SD) of the Hb. We also analysed the patients with most of the suggestions confirmed (ACM compliant group). ACM increased the percentage of Hb in range: 80.9% in IP2, compared with 72.7% in the CP and reduced the intake of darbepoetin (IP1: 20 [70]; CP 30 [80] μg P=0.032) with less Hb fluctuation (0.91±0.49 in the CP to 0.82±0.37g/dl in IP2, P<0.05), improving in the ACM compliant group. The secondary outcomes decreased with the use of ACM. ACM helps to obtain better anaemia results in haemodialysis patients, minimising the risks of treatment with ESAs and reducing costs. Copyright © 2018 Sociedad Española de Nefrología. Published by Elsevier España, S.L.U. All rights reserved.

  12. Selected Publications in Image Understanding and Computer Vision from 1974 to 1983

    1985-04-18

    Germany, September 26-28, 1978), Plenum, New York, 1979. 9. Reconnaissance des Formes et Intelligence Artificielle (2’me Congres AFCET-IRIA, Toulouse...the last decade. .To L..... ABBREVIATIONS - AI Artificial Intelligence BC Biological Cybernetics CACM Communications of the ACM CG Computer Graphics... Intelligence PACM Proceedings of the ACM "P-IEEE Proceedings of the IEEE P-NCC Proceedings of the National Computer Conference PR Pattern Recognition PRL

  13. A Study on How Conference Papers are Extended into Journal Articles in the Fields of Information Management

    Yu-Hui Lu

    2016-12-01

    Full Text Available In recent years, some scholarly journals have indicated that they accept rewritten or extended version of a conference paper as long as new content are added to the journal article manuscript and that the original conference paper is included in the references. The extended publishing of conference papers now becomes topic worthy of investigation. This study analyzed the extended works of the conference papers from three major conferences in the fields of information management, i.e., Association for Computing Machinery (ACM’s ACM Conference on Electronic Commerce (ACM EC, ACM Conference on Knowledge Discovery and Data Mining (ACM KDD, and ACM International Conference on Information and Knowledge Management (ACM CIKM. Papers from the 2011 meetings were used as the sample to understand to what extent conference papers have been extended into journal articles and other forms and the lag between conference and journal publishing. It also examined the differences between the conference papers and their extended versions (i.e., journal papers by comparing the changes in authorship, references, article length, tables, and figures. It reveals the current practices of extending conference papers for journal publishing in the information management fields and may help us understand the contemporary scholarly publishing behavior. [Article content in Chinese

  14. An international observational study suggests that artificial intelligence for clinical decision support optimizes anemia management in hemodialysis patients.

    Barbieri, Carlo; Molina, Manuel; Ponce, Pedro; Tothova, Monika; Cattinelli, Isabella; Ion Titapiccolo, Jasmine; Mari, Flavio; Amato, Claudia; Leipold, Frank; Wehmeyer, Wolfgang; Stuard, Stefano; Stopper, Andrea; Canaud, Bernard

    2016-08-01

    Managing anemia in hemodialysis patients can be challenging because of competing therapeutic targets and individual variability. Because therapy recommendations provided by a decision support system can benefit both patients and doctors, we evaluated the impact of an artificial intelligence decision support system, the Anemia Control Model (ACM), on anemia outcomes. Based on patient profiles, the ACM was built to recommend suitable erythropoietic-stimulating agent doses. Our retrospective study consisted of a 12-month control phase (standard anemia care), followed by a 12-month observation phase (ACM-guided care) encompassing 752 patients undergoing hemodialysis therapy in 3 NephroCare clinics located in separate countries. The percentage of hemoglobin values on target, the median darbepoetin dose, and individual hemoglobin fluctuation (estimated from the intrapatient hemoglobin standard deviation) were deemed primary outcomes. In the observation phase, median darbepoetin consumption significantly decreased from 0.63 to 0.46 μg/kg/month, whereas on-target hemoglobin values significantly increased from 70.6% to 76.6%, reaching 83.2% when the ACM suggestions were implemented. Moreover, ACM introduction led to a significant decrease in hemoglobin fluctuation (intrapatient standard deviation decreased from 0.95 g/dl to 0.83 g/dl). Thus, ACM support helped improve anemia outcomes of hemodialysis patients, minimizing erythropoietic-stimulating agent use with the potential to reduce the cost of treatment. Copyright © 2016 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

  15. Effect of Artocarpus communis Extract on UVB Irradiation-Induced Oxidative Stress and Inflammation in Hairless Mice

    Feng-Lin Yen

    2013-02-01

    Full Text Available Administration of antioxidants and anti-inflammatory agents is an effective strategy for preventing ultraviolet (UV irradiation-induced skin damage. Artocarpus communis possesses several pharmacological activities, such as antioxidant, anticancer and anti-inflammation. However, the photoprotective activity of methanol extract of A. communis heartwood (ACM in ultraviolet irradiation-induced skin damage has not yet been investigated. The present study was performed using ultraviolet absorption, histopathological observation, antioxidant and anti-inflammation assays to elucidate the mechanism of the photoprotective activity of ACM. Our results indicated that ACM displayed a UVA and UVB absorption effect and then effectively decreased scaly skin, epidermis thickness and sunburn cells during ultraviolet irradiation in hairless mice. ACM not only decreased ultraviolet irradiation-mediated oxidative stress, including lowering the overproduction of reactive oxygen species and lipid peroxidation (p < 0.05, but also reduced the levels of pro-inflammatory cytokines, including tumor necrosis factor-α (TNF-α and interleukin 1β. Additionally, ACM can decrease the synthesis of cytosolic phospholipase A2, cyclooxygenase, inducible nitric oxide synthase and vascular cell adhesion molecular-1 via inhibiting TNF-α-independent pathways (p < 0.05 in UVB-mediated inflammation and formation of sunburn cells. Consequently, we concluded that ACM extract has a photoprotective effect against UVB-induced oxidative stress and inflammation due to its sunscreen property, and its topical formulations may be developed as therapeutic and/or cosmetic products in further studies.

  16. Exploring digenic inheritance in arrhythmogenic cardiomyopathy.

    König, Eva; Volpato, Claudia Béu; Motta, Benedetta Maria; Blankenburg, Hagen; Picard, Anne; Pramstaller, Peter; Casella, Michela; Rauhe, Werner; Pompilio, Giulio; Meraviglia, Viviana; Domingues, Francisco S; Sommariva, Elena; Rossini, Alessandra

    2017-12-08

    Arrhythmogenic cardiomyopathy (ACM) is an inherited genetic disorder, characterized by the substitution of heart muscle with fibro-fatty tissue and severe ventricular arrhythmias, often leading to heart failure and sudden cardiac death. ACM is considered a monogenic disorder, but the low penetrance of mutations identified in patients suggests the involvement of additional genetic or environmental factors. We used whole exome sequencing to investigate digenic inheritance in two ACM families where previous diagnostic tests have revealed a PKP2 mutation in all affected and some healthy individuals. In family members with PKP2 mutations we determined all genes that harbor variants in affected but not in healthy carriers or vice versa. We computationally prioritized the most likely candidates, focusing on known ACM genes and genes related to PKP2 through protein interactions, functional relationships, or shared biological processes. We identified four candidate genes in family 1, namely DAG1, DAB2IP, CTBP2 and TCF25, and eleven candidate genes in family 2. The most promising gene in the second family is TTN, a gene previously associated with ACM, in which the affected individual harbors two rare deleterious-predicted missense variants, one of which is located in the protein's only serine kinase domain. In this study we report genes that might act as digenic players in ACM pathogenesis, on the basis of co-segregation with PKP2 mutations. Validation in larger cohorts is still required to prove the utility of this model.

  17. Skin derived precursor Schwann cell-generated acellular matrix modified chitosan/silk scaffolds for bridging rat sciatic nerve gap.

    Zhu, Changlai; Huang, Jing; Xue, Chengbin; Wang, Yaxian; Wang, Shengran; Bao, Shuangxi; Chen, Ruyue; Li, Yuan; Gu, Yun

    2017-12-27

    Extracellular/acellular matrix has been attracted much research interests for its unique biological characteristics, and ACM modified neural scaffolds shows the remarkable role of promoting peripheral nerve regeneration. In this study, skin-derived precursors pre-differentiated into Schwann cells (SKP-SCs) were used as parent cells to generate acellular(ACM) for constructing a ACM-modified neural scaffold. SKP-SCs were co-cultured with chitosan nerve guidance conduits (NGC) and silk fibroin filamentous fillers, followed by decellularization to stimulate ACM deposition. This NGC-based, SKP-SC-derived ACM-modified neural scaffold was used for bridging a 10 mm long rat sciatic nerve gap. Histological and functional evaluation after grafting demonstrated that regenerative outcomes achieved by this engineered neural scaffold were better than those achieved by a plain chitosan-silk fibroin scaffold, and suggested the benefits of SKP-SC-derived ACM for peripheral nerve repair. Copyright © 2017 Elsevier Ireland Ltd and Japan Neuroscience Society. All rights reserved.

  18. Self-contained induction of neurons from human embryonic stem cells.

    Tsuyoshi Okuno

    Full Text Available BACKGROUND: Neurons and glial cells can be efficiently induced from mouse embryonic stem (ES cells in a conditioned medium collected from rat primary-cultured astrocytes (P-ACM. However, the use of rodent primary cells for clinical applications may be hampered by limited supply and risk of contamination with xeno-proteins. METHODOLOGY/PRINCIPAL FINDINGS: We have developed an alternative method for unimpeded production of human neurons under xeno-free conditions. Initially, neural stem cells in sphere-like clusters were induced from human ES (hES cells after being cultured in P-ACM under free-floating conditions. The resultant neural stem cells could circumferentially proliferate under subsequent adhesive culture, and selectively differentiate into neurons or astrocytes by changing the medium to P-ACM or G5, respectively. These hES cell-derived neurons and astrocytes could procure functions similar to those of primary cells. Interestingly, a conditioned medium obtained from the hES cell-derived astrocytes (ES-ACM could successfully be used to substitute P-ACM for induction of neurons. Neurons made by this method could survive in mice brain after xeno-transplantation. CONCLUSION/SIGNIFICANCE: By inducing astrocytes from hES cells in a chemically defined medium, we could produce human neurons without the use of P-ACM. This self-serving method provides an unlimited source of human neural cells and may facilitate clinical applications of hES cells for neurological diseases.

  19. Atrial remodeling and metabolic dysfunction in idiopathic isolated fibrotic atrial cardiomyopathy.

    Cui, Chang; Jiang, Xiaohong; Ju, Weizhu; Wang, Jiaxian; Wang, Daowu; Sun, Zheng; Chen, Minglong

    2018-04-26

    Idiopathic isolated fibrotic atrial cardiomyopathy (IIF-ACM) is a novel subtype of cardiomyopathy characterized by atrial fibrosis that does not involve the ventricular myocardium and is associated with significant atrial tachyarrhythmia. The mechanisms underlying its pathogenesis are unknown. Atrium samples were obtained from 3 patients with IIF-ACM via surgical intervention. Control samples were consisted of 3 atrium biopsies from patients with congenital heart disease and normal sinus rhythm, matched for gender, age and basic clinical characteristics. Comparative histology, immunofluorescence staining, electron microscopy and proteomics analyses were carried out to explore the unique pathogenesis of IIF-ACM. IIF-ACM atria displayed disordered myofibrils, profound fibrosis and mitochondrial damages compared to the control atria. Proteomics profiling identified metabolic pathways as the most profound changes in IIF-ACM. Our study suggested that metabolic changes in the atrial myocardium caused mitochondrial oxidative stress and potential cell damage, which further led to atrial fibrosis and myofibril disorganization, the characteristic phenotype of IIF-ACM. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Enhancement of critical currents in bulk and Ag-sheathed Bi(Pb)-2223 superconductors

    Brauer, D.J.; Eujen, R.; Hudepohl, J.

    1991-01-01

    This paper reports on the superconducting properties of the Bi(Pb)-2223 phase that have been optimized. Prolonged annealing of coarse powder raised j c in bulk samples to as high as 1100 Acm -2 at 77 K. the temperature dependence was studied between 96 and 4.2 K whereby j c rose gradually from 120 to 2100 Acm -2 . T c dropped from 107 K to 64 K in magnetic fields up to 4 T but decreased by only 1 K/T in higher fields. A tape prepared by rolling and subsequent annealing of Ag tubes containing Bi(Pb)-2223 powder exhibited a j c of 1700 Acm -2 at 77 K and 11000 Acm -2 at 4.2 K. The latter j c dropped to 3000 Acm -2 in a magnetic field of 0.25 t, but it was still 1200 Acm -2 in a 10 T field. A tape fabricated by pressing a drawn and annealed wire proved to be less sensitive to low magnetic fields

  1. The incidence of Arnold–Chiari malformation in neurological practice

    E. A. Kantimirova

    2015-01-01

    Full Text Available Arnold-Chiari malformation (ACM is a group of congenital hindbrain malformations affecting the structural relationships between the cerebellum, brain stem, top cervical spinal cord, and bones of the skull base. In clinical practice, ACM types 0 and 1 are more common and types 2, 3, and 4 belong to rare severe (often fatal congenital malformations.Objective: to study gender differences in the incidence of ACM types 0 and 1 in outpatient neurological practice.Patients and methods. A total 2039 case records of outpatients who had visited a neurologist of the Krasnoyarsk University clinic in 2008–2014 were analyzed. Neurological and neuroradiological (1.5 Tesla brain magnetic resonance imaging, phase-contrast spinal cerebral fluid flow imaging diagnostic techniques were used. 3.4% (70/2039 of cases were randomized according to the criteria of inclusion and exception. An entire sample included 70 ACM patients (median age, 25 [17; 34] years (30 (42.8–7.1% men and 40 (57.2–7.1% women.Results. There was an increase in the incidence of ACM type 1 in the women than in the men. Conclusion. It is necessary to develop a new strategy for the prophylactic medical examination of patients with ACM to improve primary and specialized outpatient health care.

  2. RGD-modified liposomes enhance efficiency of aclacinomycin A delivery: evaluation of their effect in lung cancer

    Feng C

    2015-08-01

    Full Text Available Chan Feng,1,* Xiaoyan Li,2,* Chunyan Dong,1 Xuemei Zhang,1 Xie Zhang,1 Yong Gao11Department of Oncology, Shanghai East Hospital, Tongji University, Shanghai, 2Shanghai Tenth People’s Hospital, Tongji University, Shanghai, People’s Republic of China*These authors contributed equally to this workAbstract: In this study, long-circulating Arg-Gly-Asp (RGD-modified aclacinomycin A (ACM liposomes were prepared by thin film hydration method. Their morphology, particle size, encapsulation efficiency, and in vitro release were investigated. The RGD-ACM liposomes was about 160 nm in size and had the visual appearance of a yellowish suspension. The zeta potential was -22.2 mV and the encapsulation efficiency was more than 93%. The drug-release behavior of the RGD-ACM liposomes showed a biphasic pattern, with an initial burst release and followed by sustained release at a constant rate. After being dissolved in phosphate-buffered saline (pH 7.4 and kept at 4°C for one month, the liposomes did not aggregate and still had the appearance of a milky white colloidal solution. In a pharmacokinetic study, rats treated with RGD-ACM liposomes showed slightly higher plasma concentrations than those treated with ACM liposomes. Maximum plasma concentrations of RGD-ACM liposomes and ACM liposomes were 4,532 and 3,425 ng/mL, respectively. RGD-ACM liposomes had a higher AUC0–∞ (1.54-fold, mean residence time (2.09-fold, and elimination half-life (1.2-fold when compared with ACM liposomes. In an in vivo study in mice, both types of liposomes inhibited growth of human lung adenocarcinoma (A549 cells and markedly decreased tumor size when compared with the control group. There were no obvious pathological tissue changes in any of the treatment groups. Our results indicate that RGD-modified ACM liposomes have a better antitumor effect in vivo than their unmodified counterparts.Keywords: RGD, aclacinomycin A, long-circulating liposomes, pharmacokinetic, tumor

  3. Validation of chronic kidney disease risk categorization system in Chinese patients with kidney disease: A cohort study.

    Liu, Qingyan; Lv, Jicheng; Li, Haixia; Jiao, Lili; Yang, Hongyun; Song, Yinan; Xu, Guobin

    2015-12-01

    To validate the Kidney Disease: Improving Global Outcomes (KDIGO) guidelines risk stratification system based on the combination of estimated glomerular filtration rate (eGFR) and proteinuria. This was a cohort study. A total of 1219 study population were recruited. Estimated GFR and proteinuria measured by using 24 h urine protein excretion rate (PER) were predictors. Adverse outcomes included all-cause mortality (ACM) and end-stage renal disease (ESRD). Follow-up was done by regular visit, telephone interview and electronic medical records. Over a median follow-up of 4.6 years, 153 (12.6%) and 43 (3.5%) patients experienced ESRD and ACM, respectively. On multivariable analysis, the adjusted hazard ratio for ESRD and ACM (compared with patients with eGFR > 60 mL/min per 1.7  m²) was of 29.8 and 3.6 for those with eGFR of 15-29 mL/min per 1.73 m², respectively. The adjusted hazard ratio for ESRD and ACM (compared with patients with PER  500 mg/24h. Higher KDIGO guidelines risk categories (indicating lower eGFR or higher proteinuria) were associated with a graded increase in the risk for the ESRD (P < 0.001) and ACM (P < 0.001). Reclassification of KDIGO guidelines risk categories yielded net reclassification improvements for those with ESRD or ACM event (NRIevents ) of 33.3% or 30.2%. Lower eGFR and higher proteinuria are risk factors for ESRD and ACM in Chinese patients. The KDIGO guidelines risk categorization system assigned patients who went on to have the event to more appropriate CKD risk categories. © 2015 Asian Pacific Society of Nephrology.

  4. Cost-benefit analysis of avian influenza control in Nepal.

    Karki, S; Lupiani, B; Budke, C M; Karki, N P S; Rushton, J; Ivanek, R

    2015-12-01

    Numerous outbreaks of highly pathogenic avian influenza A strain H5N1 have occurred in Nepal since 2009 despite implementation of a national programme to control the disease through surveillance and culling of infected poultry flocks. The objective of the study was to use cost-benefit analysis to compare the current control programme (CCP) with the possible alternatives of: i) no intervention (i.e., absence of control measures [ACM]) and ii) vaccinating 60% of the national poultry flock twice a year. In terms of the benefit-cost ratio, findings indicate a return of US $1.94 for every dollar spent in the CCP compared with ACM. The net present value of the CCP versus ACM, i.e., the amount of money saved by implementing the CCP rather than ACM, is US $861,507 (the benefits of CCP [prevented losses which would have occurred under ACM] minus the cost of CCP). The vaccination programme yields a return of US $2.32 for every dollar spent when compared with the CCR The net present value of vaccination versus the CCP is approximately US $12 million. Sensitivity analysis indicated thatthe findings were robust to different rates of discounting, whereas results were sensitive to the assumed market loss and the number of birds affected in the outbreaks under the ACM and vaccination options. Overall, the findings of the study indicate that the CCP is economically superior to ACM, but that vaccination could give greater economic returns and may be a better control strategy. Future research should be directed towards evaluating the financial feasibility and social acceptability of the CCP and of vaccination, with an emphasis on evaluating market reaction to the presence of H5N1 infection in the country.

  5. Assessment of occupational exposure to asbestos fibers: Contribution of analytical transmission electron microscopy analysis and comparison with phase-contrast microscopy.

    Eypert-Blaison, Céline; Romero-Hariot, Anita; Clerc, Frédéric; Vincent, Raymond

    2018-03-01

    From November 2009 to October 2010, the French general directorate for labor organized a large field-study using analytical transmission electron microscopy (ATEM) to characterize occupational exposure to asbestos fibers during work on asbestos containing materials (ACM). The primary objective of this study was to establish a method and to validate the feasibility of using ATEM for the analysis of airborne asbestos of individual filters sampled in various occupational environments. For each sampling event, ATEM data were compared to those obtained by phase-contrast optical microscopy (PCOM), the WHO-recommended reference technique. A total of 265 results were obtained from 29 construction sites where workers were in contact with ACM. Data were sorted depending on the combination of the ACM type and the removal technique. For each "ACM-removal technique" combination, ATEM data were used to compute statistical indicators on short, fine and WHO asbestos fibers. Moreover, exposure was assessed taking into account the use of respiratory protective devices (RPD). As in previous studies, no simple relationship was found between results by PCOM and ATEM counting methods. Some ACM, such as asbestos-containing plasters, generated very high dust levels, and some techniques generated considerable levels of dust whatever the ACM treated. On the basis of these observations, recommendations were made to measure and control the occupational exposure limit. General prevention measures to be taken during work with ACM are also suggested. Finally, it is necessary to continue acquiring knowledge, in particular regarding RPD and the dust levels measured by ATEM for the activities not evaluated during this study.

  6. Validation of an ambulatory capacity measure in Parkinson disease: a construct derived from the Unified Parkinson's Disease Rating Scale.

    Parashos, Sotirios A; Elm, Jordan; Boyd, James T; Chou, Kelvin L; Dai, Lin; Mari, Zoltan; Morgan, John C; Sudarsky, Lewis; Wielinski, Catherine L

    2015-01-01

    A construct calculated as the sum of items 13-15, 29, 30 of the Unified Parkinson's Disease Rating Scale (UPDRS) has been used as an "Ambulatory Capacity Measure" (ACM) in Parkinson disease (PD). Its construct validity has never been examined. A similar construct, consisting of the mean value of the same UPDRS items has been used under the acronym PIGD as a measure of postural instability and gait disorder in PD. To examine the construct validity of the ACM and PIGD in PD. We analyzed data in an existing database of 340 PD patients, Hoehn and Yahr stages (HYS) 1-5 who participated in a study of falls. Number of falls (NOF) was recorded over 4 weeks, and UPDRS (mental, ADL, and motor subscales), HYS, Activities Based Confidence Scale (ABC), Freezing of Gait Questionnaire (FOG), Five Times Sit-to-Stand (FTSS), Timed Up-and Go (TUG), Gait Velocity (GV), and Berg Balance Scale (BBS) evaluations were performed. Internal consistency was assessed by Cronbach's alpha. Construct validity was assessed through correlations of the ACM and PIGD to these measures and to their summed-ranks. A coefficient of determination was calculated through linear regression. Mean age was 71.4, mean age at diagnosis 61.4 years; 46% were women; mean UPDRS subscale scores were: Mental 3.7; ADL 15.7; motor: 27.1; mean ACM was 6.51, and mean PIGD 1.30. Cronbach's alpha was 0.78 for both ACM and PIGD. Spearman correlation coefficients between the ACM/PIGD and ABC, FOG, TUG, GV and BBS were 0.69, 0.72, 0.67, 0.58, and 0.70 respectively. Correlation between the ACM/PIGD and summed-ranks of HYS, NOF, ABC, FOG, FTSS, TUG, GV and BBS was high (Spearman r = 0.823, p < 0.0001); 68% of the variability in the summed-ranks was explained by ACM/PIGD. The ACM and the PIGD are valid global measures and accurately reflect the combined effects of the various components of ambulatory capacity in PD patients with HY stages 1-4.

  7. Generation of monoclonal antibodies against prostate specific antigen (PSA) for the detection of PSA and its purification

    Acevedo Castro, Boris Ernesto

    2012-01-01

    The prostate cancer in Cuba is a problem of health (2672 diagnosed cases and 2769 deaths in 2007). Various diagnostic methods have been implemented for the detection and management of this disease, emphasizing among them (PSA) prostate-specific antigen serological determination. At this work was generated and characterized a panel of 11 antibodies (AcMs) monoclonal IgG1 detected with high affinity described major epitopes of the PSA, both in solution and attached to the test plate. From the panel obtained AcMs was the standardization of an essay type ELISA for the detection of serum total PSA (associated and free) equimolar, based on antibody monoclonal CB-PSA.4 in the coating and the CB-PSA.9 coupled with biotin as liner, with a detection limit of 0.15 ng/mL. Similarly, standardized system for detection in serum free PSA, based on the AcMs CB-PSA.4 (coating) and CB-PSA.2 coupled with biotin (liner), with a detection limit of 0.5 ng/mL. Finally, with the purpose of using PSA as standard in trials type ELISA, developed a simple method of inmunopurificación based on the AcM, CB-PSA.2, which was obtained the PSA with a purity exceeding 90%. Immunoassay Centre on the basis of the AcMs panel and the results of this study, developed and recorded two diagnostic systems for the detection of PSA in human serum. (author)

  8. Preparation of Highly Porous Binderless Active Carbon Monoliths from Waste Aspen Sawdust

    Dawei Li

    2014-01-01

    Full Text Available Waste aspen sawdust was used as a precursor to prepare binderless active carbon monoliths (ACMs with high porosities. The ACMs were prepared by activation with H3PO4 at different activation temperatures (500 to 700 °C and retention times (1 to 3 h. Their morphologies, yields, textural properties, and microcrystalline structures were investigated using scanning electron microscopy (SEM, an analytical balance, N2 adsorption/desorption techniques, and X-ray diffraction (XRD. The results indicated that waste aspen sawdust could be successfully converted into highly porous binderless ACMs. The apparent specific surface area (SSA and yield of ACMs were in the range of 688 to 951 m2/g and 26.6 to 36.2%, respectively. Highly microporous ACMs with a micropore percentage of 91.1%, apparent specific surface area of 951 m2/g, pore volume of 0.481 mL/g, and bulk density of 0.56 g/mL could be produced by activation at 700 °C for 1 h. Increasing the activation temperature or retention time increased the specific surface area, pore volume, and turbostratic degree, but decreased the yield.

  9. Progress in scale-up of second-generation HTS conductor

    Selvamanickam, V.; Chen, Y.; Xiong, X.; Xie, Y.; Zhang, X.; Qiao, Y.; Reeves, J.; Rar, A.; Schmidt, R.; Lenseth, K.

    2007-01-01

    Tremendous progress has been recently made in the achievement of high-performance, high-speed, long-length second-generation (2G) HTS conductors. Using ion beam assisted deposition (IBAD) MgO and metal organic chemical vapor deposition (MOCVD), SuperPower has scaled up tape lengths to 427 m with a minimum critical current value of 191 A/cm corresponding to a critical current x length performance of 81,550 m. Tape speeds up to 120 m/h have been reached with IBAD MgO, up to 80 m/h with buffer deposition and up to 45 m/h with MOCVD, all in single pass processing of 12 mm wide tape. Critical current value of 227 A/cm has been achieved in a 203 m long tape produced in an all-high-speed fabrication process. Critical current values have been raised to 721 A/cm, 592 A/cm and 486 A/cm in short, reel-to-reel processed tape, over 1 m length and over 11.1 m, respectively, using thicker MOCVD HTS films. Finally, over 10,000 m of copper-stabilized, 4 mm wide conductor has been produced and tested for delivery to the Albany Cable project. The average critical current of the 10,000 m lot was 81 A

  10. Progress in scale-up of second-generation HTS conductor

    Selvamanickam, V. [SuperPower Inc., 450 Duane Avenue, Schenectady, NY 12304 (United States)], E-mail: vselva@igc.com; Chen, Y.; Xiong, X.; Xie, Y.; Zhang, X.; Qiao, Y.; Reeves, J.; Rar, A.; Schmidt, R.; Lenseth, K. [SuperPower Inc., 450 Duane Avenue, Schenectady, NY 12304 (United States)

    2007-10-01

    Tremendous progress has been recently made in the achievement of high-performance, high-speed, long-length second-generation (2G) HTS conductors. Using ion beam assisted deposition (IBAD) MgO and metal organic chemical vapor deposition (MOCVD), SuperPower has scaled up tape lengths to 427 m with a minimum critical current value of 191 A/cm corresponding to a critical current x length performance of 81,550 m. Tape speeds up to 120 m/h have been reached with IBAD MgO, up to 80 m/h with buffer deposition and up to 45 m/h with MOCVD, all in single pass processing of 12 mm wide tape. Critical current value of 227 A/cm has been achieved in a 203 m long tape produced in an all-high-speed fabrication process. Critical current values have been raised to 721 A/cm, 592 A/cm and 486 A/cm in short, reel-to-reel processed tape, over 1 m length and over 11.1 m, respectively, using thicker MOCVD HTS films. Finally, over 10,000 m of copper-stabilized, 4 mm wide conductor has been produced and tested for delivery to the Albany Cable project. The average critical current of the 10,000 m lot was 81 A.

  11. Supply chain challenges in the South African automotive sector: do location, size and age matter?

    Micheline Juliana Naude

    2013-11-01

    Full Text Available The South African automotive industry makes an important contribution to the South African economy. However, there are deficiencies within the local automotive component manufacturers’ (ACMs supplier base and therefore automotive assemblers, or original equipment manufacturers (OEMs, have to import many of their parts requirements. These deficiencies are caused by ACMs’ lack of technology, global supply capability, cost competitiveness and their geographic location (ACMs are scattered across the country. A study was conducted to explore the supply chain challenges South African ACMs face and whether the location, size and age of participating ACMs have a bearing on whether they face the same challenges. The results revealed that the most significant supply chain challenges in South Africa were in the customer relationship category. From the hypotheses testing, the conclusion could be drawn that, in general, participating ACMs face common supply chain challenges, irrespective of their location, age and size.This article contributes to the published research on the topic and the findings reveal that business opportunities in the automotive industry exist for entrepreneurs aspiring to enter into the automotive component industry.

  12. Generation of monoclonal antibodies against prostate specific antigen (PSA) for the detection of PSA and its purification; Generación de anticuerpos monoclonales contra el antígeno específico de próstata (PSA) para la detección del PSA y su purificación

    Acevedo Castro, Boris Ernesto [Centro de Ingeniería Genética y Biotecnología, CIGB, La Habana (Cuba)

    2012-07-01

    The prostate cancer in Cuba is a problem of health (2672 diagnosed cases and 2769 deaths in 2007). Various diagnostic methods have been implemented for the detection and management of this disease, emphasizing among them (PSA) prostate-specific antigen serological determination. At this work was generated and characterized a panel of 11 antibodies (AcMs) monoclonal IgG1 detected with high affinity described major epitopes of the PSA, both in solution and attached to the test plate. From the panel obtained AcMs was the standardization of an essay type ELISA for the detection of serum total PSA (associated and free) equimolar, based on antibody monoclonal CB-PSA.4 in the coating and the CB-PSA.9 coupled with biotin as liner, with a detection limit of 0.15 ng/mL. Similarly, standardized system for detection in serum free PSA, based on the AcMs CB-PSA.4 (coating) and CB-PSA.2 coupled with biotin (liner), with a detection limit of 0.5 ng/mL. Finally, with the purpose of using PSA as standard in trials type ELISA, developed a simple method of inmunopurificación based on the AcM, CB-PSA.2, which was obtained the PSA with a purity exceeding 90%. Immunoassay Centre on the basis of the AcMs panel and the results of this study, developed and recorded two diagnostic systems for the detection of PSA in human serum. (author)

  13. On the Relationship between Variational Level Set-Based and SOM-Based Active Contours

    Abdelsamea, Mohammed M.; Gnecco, Giorgio; Gaber, Mohamed Medhat; Elyan, Eyad

    2015-01-01

    Most Active Contour Models (ACMs) deal with the image segmentation problem as a functional optimization problem, as they work on dividing an image into several regions by optimizing a suitable functional. Among ACMs, variational level set methods have been used to build an active contour with the aim of modeling arbitrarily complex shapes. Moreover, they can handle also topological changes of the contours. Self-Organizing Maps (SOMs) have attracted the attention of many computer vision scientists, particularly in modeling an active contour based on the idea of utilizing the prototypes (weights) of a SOM to control the evolution of the contour. SOM-based models have been proposed in general with the aim of exploiting the specific ability of SOMs to learn the edge-map information via their topology preservation property and overcoming some drawbacks of other ACMs, such as trapping into local minima of the image energy functional to be minimized in such models. In this survey, we illustrate the main concepts of variational level set-based ACMs, SOM-based ACMs, and their relationship and review in a comprehensive fashion the development of their state-of-the-art models from a machine learning perspective, with a focus on their strengths and weaknesses. PMID:25960736

  14. Effect of electrolyte concentration on performance of supercapacitor carbon electrode from fibers of oil palm empty fruit bunches

    Farma, R.; Awitdrus,; Taer, E. [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Departement of Physics, Faculty of Mathematics and Natural Sciences, University of Riau, 28293 Pekanbaru, Riau (Indonesia); Deraman, M., E-mail: madra@ukm.my; Talib, I. A.; Omar, R.; Ishak, M. M.; Basri, N. H.; Dolah, B. N. M. [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

    2015-04-16

    Fibers of oil palm empty fruit bunches were used to produce self-adhesive carbon grains (SACG). The SACG green monoliths were carbonized in N{sub 2} environment at 800°C to produce carbon monoliths (CM) and the CM was CO{sub 2} activated at 800°C for 4 hour to produce activated carbon monolith electrodes (ACM). The physical properties of the CMs and ACMs were investigated using X-ray diffraction, field emission scanning electron microscopy and nitrogen adsorption-desorption. ACMs were used as electrode to fabricate symmetry supercapacitor cells and the cells which used H{sub 2}SO{sub 4} electrolyte at 0.5, 1.0 and 1.5 M were investigated using electrochemical impedance spectroscopy, cyclic voltammetry and galvanostatic charge-discharge standard techniques. In this paper we report the physical properties of the ACM electrodes and the effect of electrolyte concentration on the electrochemical properties the ACM electrodes.

  15. Facilitated transport of Cr(III) through activated composite membrane containing di-(2-ethylhexyl)phosphoric acid (DEHPA) as carrier agent

    Arslan, Gulsin; Tor, Ali; Cengeloglu, Yunus; Ersoz, Mustafa

    2009-01-01

    The facilitated transport of chromium(III) through activated composite membrane (ACM) containing di-(2-ethylhexyl) phosphoric acid (DEHPA) was investigated. DEHPA was immobilised by interfacial polymerisation on polysulfone layer which was deposited on non-woven fabric by using spin coater. Then, ACM was characterised by using scanning electron microscopy (SEM), contact angle measurements and atomic force microscopy (AFM). Initially, batch experiments of liquid-liquid distribution of Cr(III) and the extractant (DEHPA) were carried out to determine the appropriate pH of the feed phase and the results showed that maximum extraction of Cr(III) was achieved at a pH of 4. It was also found that Cr(III) and DEHPA reacted in 1/1 molar ratio. The effects of Cr(III) (in feed phase), HCl (in stripping phase) and DEHPA (in ACM) concentrations were investigated. DEHPA concentration varies from 0.1 to 1.0 M and it was determined that the transport of Cr(III) increased with the carrier concentration up to 0.8 M. It was also observed that the transport of Cr(III) through the ACM tended to increase with Cr(III) and HCl concentrations. The stability of ACM was also confirmed with replicate experiments.

  16. CMT scaling analysis and distortion evaluation in passive integral test facility

    Deng Chengcheng; Qin Benke; Wang Han; Chang Huajian

    2013-01-01

    Core makeup tank (CMT) is the crucial device of AP1000 passive core cooling system, and reasonable scaling analysis of CMT plays a key role in the design of passive integral test facilities. H2TS method was used to perform scaling analysis for both circulating mode and draining mode of CMT. And then, the similarity criteria for CMT important processes were applied in the CMT scaling design of the ACME (advanced core-cooling mechanism experiment) facility now being built in China. Furthermore, the scaling distortion results of CMT characteristic Ⅱ groups of ACME were calculated. At last, the reason of scaling distortion was analyzed and the distortion evaluation was conducted for ACME facility. The dominant processes of CMT circulating mode can be adequately simulated in the ACME facility, but the steam condensation process during CMT draining is not well preserved because the excessive CMT mass leads to more energy to be absorbed by cold metal. However, comprehensive analysis indicates that the ACME facility with high-pressure simulation scheme is able to properly represent CMT's important phenomena and processes of prototype nuclear plant. (authors)

  17. Morphological changes during enhanced carbonation of asbestos containing material and its comparison to magnesium silicate minerals

    Gadikota, Greeshma; Natali, Claudio; Boschi, Chiara; Park, Ah-Hyung Alissa

    2014-01-01

    The disintegration of asbestos containing materials (ACM) over time can result in the mobilization of toxic chrysotile ((Mg, Fe) 3 Si 2 O 5 (OH) 4 )) fibers. Therefore, carbonation of these materials can be used to alter the fibrous morphology of asbestos and help mitigate anthropogenic CO 2 emissions, depending on the amount of available alkaline metal in the materials. A series of high pressure carbonation experiments were performed in a batch reactor at P CO2 of 139 atm using solvents containing different ligands (i.e., oxalate and acetate). The results of ACM carbonation were compared to those of magnesium silicate minerals which have been proposed to permanently store CO 2 via mineral carbonation. The study revealed that oxalate even at a low concentration of 0.1 M was effective in enhancing the extent of ACM carbonation and higher reaction temperatures also resulted in increased ACM carbonation. Formation of phases such as dolomite ((Ca, Mg)(CO 3 ) 2 ), whewellite (CaC 2 O 4 ·H 2 O) and glushinskite (MgC 2 O 4 ·2H 2 O) and a reduction in the chrysotile content was noted. Significant changes in the particle size and surface morphologies of ACM and magnesium silicate minerals toward non-fibrous structures were observed after their carbonation

  18. Studies on the effects of adriamycin-derivatives in combination with X-rays on MeWo- and Be11-cells

    Krueger, M.; Beuningen, D. van; Streffer, C.

    1990-01-01

    The survival rate of human melanoma cells after X-ray irradiation, treamtment with adriamycin derivatives and combined treatment with X-rays and adriamycin derivatives was measured by means of the colony formation test. After X-ray irradiation the melanoma cells showed a high resistance for cell survival. In all tests the Be11-cells were more resistant than MeWo-cells. On combined exposure especially with higher doses of adriamycin derivatives, both cell lines showed the interesting effect, that with increasing concentration the survival rate decreased whereas the D 0 increased. Aclacinomycin-A (ACM-A) and Pirarubicin reduced recovery processes after X-ray irradiation. Therefore Be11-cells showed a four times higher DMF (dosis modifying factor) after ACM-A-treatment than MeWo-cells. Low ACM-A-concentrations combined with low X-ray doses showed on both cell lines supraadditive effects. The effect of pirarubicin was in most of the tests only additive. Compared with ACM-A, pirarubicin was less cytotoxic, showed a larger therapeutic range, caused a smaller D 0 and D q and had a supraadditive effect in low concentrations on both cell lines. For clinical combined therapy with patients ACM-A is probably better suited than pirarubicin. (orig.) [de

  19. Morphological changes during enhanced carbonation of asbestos containing material and its comparison to magnesium silicate minerals

    Gadikota, Greeshma [Department of Chemical Engineering, Columbia University, 500 West 120th Street, New York, NY 10027 (United States); Natali, Claudio; Boschi, Chiara [Institute of Geosciences and Earth Resources – National Research Council, Pisa (Italy); Park, Ah-Hyung Alissa, E-mail: ap2622@columbia.edu [Department of Earth and Environmental Engineering, Columbia University, 500 West 120th Street, New York, NY 10027 (United States); Department of Chemical Engineering, Columbia University, 500 West 120th Street, New York, NY 10027 (United States); Lenfest Center for Sustainable Energy, Columbia University, 500 West 120th Street, New York, NY 10027 (United States)

    2014-01-15

    The disintegration of asbestos containing materials (ACM) over time can result in the mobilization of toxic chrysotile ((Mg, Fe){sub 3}Si{sub 2}O{sub 5}(OH){sub 4})) fibers. Therefore, carbonation of these materials can be used to alter the fibrous morphology of asbestos and help mitigate anthropogenic CO{sub 2} emissions, depending on the amount of available alkaline metal in the materials. A series of high pressure carbonation experiments were performed in a batch reactor at P{sub CO2} of 139 atm using solvents containing different ligands (i.e., oxalate and acetate). The results of ACM carbonation were compared to those of magnesium silicate minerals which have been proposed to permanently store CO{sub 2} via mineral carbonation. The study revealed that oxalate even at a low concentration of 0.1 M was effective in enhancing the extent of ACM carbonation and higher reaction temperatures also resulted in increased ACM carbonation. Formation of phases such as dolomite ((Ca, Mg)(CO{sub 3}){sub 2}), whewellite (CaC{sub 2}O{sub 4}·H{sub 2}O) and glushinskite (MgC{sub 2}O{sub 4}·2H{sub 2}O) and a reduction in the chrysotile content was noted. Significant changes in the particle size and surface morphologies of ACM and magnesium silicate minerals toward non-fibrous structures were observed after their carbonation.

  20. Estimation of the economic and health impact of complications of type 2 diabetes mellitus in the autonomous community of Madrid (Spain).

    Arrieta, Francisco; Rubio-Terrés, Carlos; Rubio-Rodríguez, Darío; Magaña, Ana; Piñera, Marbella; Iglesias, Pedro; Nogales, Pedro; Calañas, Alfonso; Novella, Blanca; Botella-Carretero, José Ignacio; Debán, Carlos; Zamarrón, Isabel; Mora, Gustavo; Balsa, José Antonio; Vázquez, Clotilde

    2014-04-01

    To estimate the economic and health impact of chronic complications (macrovascular and microvascular) of type 2 diabetes mellitus (T2DM) in the autonomous community of Madrid (Spain) (ACM). The number of expected complications was obtained from a descriptive, cross-sectional study on a cohort of 3,268 patients with T2DM from the ACM. Cost of complications (€, 2012) was assessed both at hospitals and in primary care. The number of medical visits in primary care and drug treatment for complications were collected by a panel of 21 physicians experienced in treatment of T2DM. Population and epidemiological data and healthcare costs were obtained from Spanish sources. Univariate sensitivity analyses were performed. It is estimated that there are 390,944 patients with T2DM in the ACM, and that they experience 172,406 and 212,283 macrovascular and microvascular complications respectively during their lifetimes. Mean cost of T2DM complications per patient is estimated at € 4,121.54 (66% due to macrovascular complications). The economic impact of T2DM complications in the ACM would be € 1,611 million (1,065 and 545 millions from macrovascular and microvascular complications respectively). The economic impact would range from € 1,249 and 2.509 million euro depending on T2DM prevalence. Complications of T2DM have a great health and economic impact in ACM. Copyright © 2013 SEEN. Published by Elsevier Espana. All rights reserved.

  1. Facilitated transport of Cr(III) through activated composite membrane containing di-(2-ethylhexyl)phosphoric acid (DEHPA) as carrier agent

    Arslan, Gulsin [Department of Chemistry, Selcuk University, 42031, Campus, Konya (Turkey); Tor, Ali, E-mail: ator@selcuk.edu.tr [Department of Environmental Engineering, Selcuk University, 42031 Campus, Konya (Turkey); Cengeloglu, Yunus; Ersoz, Mustafa [Department of Chemistry, Selcuk University, 42031, Campus, Konya (Turkey)

    2009-06-15

    The facilitated transport of chromium(III) through activated composite membrane (ACM) containing di-(2-ethylhexyl) phosphoric acid (DEHPA) was investigated. DEHPA was immobilised by interfacial polymerisation on polysulfone layer which was deposited on non-woven fabric by using spin coater. Then, ACM was characterised by using scanning electron microscopy (SEM), contact angle measurements and atomic force microscopy (AFM). Initially, batch experiments of liquid-liquid distribution of Cr(III) and the extractant (DEHPA) were carried out to determine the appropriate pH of the feed phase and the results showed that maximum extraction of Cr(III) was achieved at a pH of 4. It was also found that Cr(III) and DEHPA reacted in 1/1 molar ratio. The effects of Cr(III) (in feed phase), HCl (in stripping phase) and DEHPA (in ACM) concentrations were investigated. DEHPA concentration varies from 0.1 to 1.0 M and it was determined that the transport of Cr(III) increased with the carrier concentration up to 0.8 M. It was also observed that the transport of Cr(III) through the ACM tended to increase with Cr(III) and HCl concentrations. The stability of ACM was also confirmed with replicate experiments.

  2. Effects of MgO impurities and micro-cracks on the critical current density of Ti-sheathed MgB2 wires

    Liang, G.; Alessandrini, M.; Yen, F.; Hanna, M.; Fang, H.; Hoyt, C.; Lv, B.; Zeng, J.; Salama, K.

    2007-01-01

    Ti-sheathed monocore MgB 2 wires with improved magnetic critical current density (J c ) have been fabricated by in situ powder-in-tube (PIT) method and characterized by magnetization, X-ray diffraction, scanning electron microscopy and electrical resistivity measurements. For the best wire, the magnetic J c values at 5 K and fields of 2 T, 5 T, and 8 T are 4.1 x 10 5 A/cm 2 , 7.8 x 10 4 A/cm 2 , and 1.4 x 10 4 A/cm 2 , respectively. At 20 K and fields of 0.5 T and 3 T, the J c values are about 3.6 x 10 5 A/cm 2 and 3.1 x 10 4 A/cm 2 , respectively, which are much higher than those of the Fe-sheathed mono-core MgB 2 wires fabricated with the same in situ PIT process and under the same fabricating conditions. It appears that the overall J c for the average Ti-sheathed wires is comparable to that of the Fe-sheathed wires. Our X-ray diffraction and scanning electron microscopy analysis indicates that J c in the Ti-sheathed MgB 2 wires can be strongly suppressed by MgO impurities and micro-cracks

  3. In situ observation of electron-beam-induced dewetting of CdSe thin film embedded in SiO2

    Fabrim, Zacarias Eduardo; Kjelstrup-Hansen, Jakob; Fichtner, Paulo F. P.

    In this work we show the dewetting process of the CdSe thin films induced by electron beam irradiation. A multilayer heterostructure of SiO2/CdSe/SiO2 was made by a magnetron sputtering process. A plan-view (PV) sample was irradiated with 200 kV electrons in the TEM with two current densities: 0.......33 A.cm2 and 1.0 A.cm2 and at 80 kV with 0.37 A.cm2. The dewetting of the CdSe film is inferred by a number of micrographs taken during the irradiation. The microstructural changes were analyzed under the assumption of being induced by ballistic collision effects in the absence of sample heating....

  4. A novel thermoplastic elastomer based on dynamically vulcanized polypropylene/acrylic rubber blends

    2008-08-01

    Full Text Available Thermoplastic elastomer based on polypropylene (PP and acrylic rubber (ACM was investigated, with special attention on the compatibilization and dynamic vulcanization. ACM component contains chlorine and carboxyl groups along the backbone, which act as center for the curing and reactive compatibilization. The last event was carried out by adding a combination of maleic anhydride-modified PP (PP-g-MA and triethylene tetramine (TETA, which act as interfacial agents between PP and ACM phases. The effectiveness of the compatibilization was suggested from mixing torque and viscosity, determined from rheological measurements. Outstanding mechanical performance, especially elongation at break, and better tensile set (lower values were obtained with the compatibilization. The dynamic vulcanization also resulted in good mechanical properties for compatibilized blends, but the performance was inferior to that observed for non vulcanized blends. The effect of the compatibilization and/or dynamic vulcanization on the dynamic mechanical, thermal, morphological and stress relaxation properties was investigated.

  5. Properties of second phase (BaSnO3, Sn) added-YBCO thick films

    Ban, E.; Matsuoka, Y.

    1997-01-01

    The improvement of the critical current density J c of YBCO thick films has been attempted by adding BaSnO 3 powder and ultrafine Sn particles, whose diameter is about 2 μm and 7 x 10 -2 μm, respectively. It was found that the addition of a small amount of these particles was effective for the enhancement of J c of thick films prepared by a liquid-phase processing method. The 1 wt.% BaSnO 3 films fired at T s =1040-1060 C and the 3 wt.% Sn films (T s =1030-1060 C) showed J c values (77 K, 0 T) of about 2.1-2.4 x 10 3 Acm -2 and 3.1-3.5 x 10 3 Acm -2 , respectively, as compared to 2.0 x 10 3 Acm -2 for the undoped films. (orig.)

  6. Efficient adsorption of Hg (II) ions in water by activated carbon modified with melamine

    Qin, Hangdao; Meng, Jingling; Chen, Jing

    2018-04-01

    Removal of Hg (II) ions from industrial wastewater is important for the water treatment, and adsorption is an efficient treatment process. Activated carbon (AC) was modified with melamine, which introduced nitrogen-containing functional groups onto AC surface. Original AC and melamine modified activated carbon (ACM) were characterized by elemental analysis, N2 adsorption-desorption, determination of the pH of the point of zero charge (pHpzc) and X-ray photoelectron spectroscopy (XPS) and their performance in the adsorption of Hg(II) ions was investigated. Langmuir model fitted the experimental data of equilibrium isotherms well. ACM showed the higher Hg (II) ions adsorption capacity, increasing more than more than 1.8 times compared to the original one. Moreover, ACM showed a wider pH range for the maximum adsorption than the parent AC.

  7. Ingenious Snake: An Adaptive Multi-Class Contours Extraction

    Li, Baolin; Zhou, Shoujun

    2018-04-01

    Active contour model (ACM) plays an important role in computer vision and medical image application. The traditional ACMs were used to extract single-class of object contours. While, simultaneous extraction of multi-class of interesting contours (i.e., various contours with closed- or open-ended) have not been solved so far. Therefore, a novel ACM model named “Ingenious Snake” is proposed to adaptively extract these interesting contours. In the first place, the ridge-points are extracted based on the local phase measurement of gradient vector flow field; the consequential ridgelines initialization are automated with high speed. Secondly, the contours’ deformation and evolvement are implemented with the ingenious snake. In the experiments, the result from initialization, deformation and evolvement are compared with the existing methods. The quantitative evaluation of the structure extraction is satisfying with respect of effectiveness and accuracy.

  8. Investigation of the alpha cluster model and the density matrix expansion in ion-ion collision

    Rashdan, M.B.M.

    1986-01-01

    This thesis deals with the investigation of the alpha cluster model (ACM) of brink and studies of the accuracy of the density matrix expansion (DME) approximation in deriving the real part of the ion-ion optical potential. the ACM is applied to calculate the inelastic 0 1 + →2 1 + charge form factor for electron scattering by 12 C to investigate the validity of this model for 12 C nucleus. it is found that the experimental curve can be fitted over the entire range of the momentum transfer by a generator - coordinate state for the 2 1 + state that consist of a superposition of two triangular ACM states with two different cluster separations and the same oscillator parameter

  9. Investigation of the fabrication process of hot-worked stainless-steel and Mo sheathed PbMo6 S8 wires

    Yamasaki, H.; Kimura, Y.

    1988-01-01

    Stainless-steel and Mo sheathed PbMo 6 S 8 wires have been fabricated by hot working from modified PbS, Mo, and MoS 2 mixed powders which were prepared by reacting Pb, Mo, and S at 530 0 C. Critical current densities were investigated for different preparation conditions, and it is revealed that obtaining continuous current path between PbMo 6 S 8 grains is the most important factor to achieve high critical current density. The J/sub c/ value of 2.8 x 10 4 Acm 2 (8 T), 7.8 x 10 3 Acm 2 (15 T), and 1.3 x 10 3 Acm 2 (23 T) was observed for the PbMo 6 S/sub 7.0/ wire heat treated at 700 0 C.copic

  10. La Esencia de la Ingeniería de Software: El Núcleo de Semat

    Ivar Jacobson

    2013-06-01

    Full Text Available Esta es una traducción del artículo que se publicó en Communications of the ACM en Diciembre de 2012 bajo el título “The Essence of Software Engineering: The SEMAT Kernel” y se realiza debido a la importancia que adquiere el tema para la audiencia de hispanoparlantes, de forma que se pueda generar un acceso a lo que constituye uno de los últimos adelantos en Ingeniería de Software. Nota: Artículo publicado originalmente en Communications of the ACM, vol. 55, no. 12, december 2012, pp. 42-49. El traductor declara tener autorización de los autores para difundir la versión en español en la Revista Latinoamericana de Ingeniería de Software, sin que ello presente incompatibilidades o vulnere los derechos de Communications of the ACM.

  11. Climate Modeling: Ocean Cavities below Ice Shelves

    Petersen, Mark Roger [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Computer, Computational, and Statistical Sciences Division

    2016-09-12

    The Accelerated Climate Model for Energy (ACME), a new initiative by the U.S. Department of Energy, includes unstructured-mesh ocean, land-ice, and sea-ice components using the Model for Prediction Across Scales (MPAS) framework. The ability to run coupled high-resolution global simulations efficiently on large, high-performance computers is a priority for ACME. Sub-ice shelf ocean cavities are a significant new capability in ACME, and will be used to better understand how changing ocean temperature and currents influence glacial melting and retreat. These simulations take advantage of the horizontal variable-resolution mesh and adaptive vertical coordinate in MPAS-Ocean, in order to place high resolution below ice shelves and near grounding lines.

  12. Formation and physical properties of YBCO thick films grown by using the electrophoretic deposition method

    Kim, U J; Kim, Y C; Han, S K; Kang, K Y

    1999-01-01

    Thick films of the YBa sub 2 Cu sub 3 O subgamma sub - subdelta (YBCO) superconductor were prepared by using the electrophoretic deposition technique and a flexible wire as the substrate. The transition temperature of the wires was 91 K, the intragranular magnetic critical current density J sub c sub g sup m sup a sup g was about 10 sup 5 A/cm sup 2 at 77 K in a weak field, and the transport J sub c sup t sup r sup a sup n sup s was about 365 A/cm sup 2 at 77 K. We calculated the intergranular magnetic critical current J sub c sub J sup m sup a sup g and the activation energy from the AC-susceptibility measurements, and their values were about 444 A/cm sup 2 at 77 K and 2.02 eV, respectively.

  13. ENHANCEMENT OF DAMPING PERFORMANCE OF POLYMERS BY FUNCTIONAL SMALL MOLECULES

    Chi-fei Wu; Saburo Akiyama

    2002-01-01

    The addition effects of organic small molecular substances N,N'-dicyclohexyl-benzothiazyl-2-sulfenamide (DZ) and 3,9-bis{ 1, 1-dimethyl-2[β-(3-tert-butyl-4-hydroxy-5-methylphenyl)propionyloxy]ethyl}-2,4,8, 10-tetraoxaspiro[5,5]-undecane (AO-80) on the dynamic mechanical properties of chlorinated polyethylene (CPE), chlorinated polypropylene (CPP), acrylate rubber (ACM) and their blends were investigated. In the case of compatible systems such as CPE/DZ and ACM/AO-80, the height of the loss tangent (tanδ) peak of a matrix polymer (CPE or ACM) increases, and its peak position shifts to a higher temperature with the addition of DZ or AO-80. By contrast, for incompatible CPE/AO-80, a novel transition appeared above the glass transition temperature of CPE. This additional transition was assigned to dissociation of the intermolecular hydrogen bond between the α-hydrogen of CPE and the hydroxyl groups of AO-80 within the AO-80-rich domain. This will provide a new concept for developing damping material. However, the minimum value between two tanδ peaks is lower. It was found that the temperature dependence of tanδ could be improved by adding chlorinated paraffin (CP) or ACM to CPE/AO-80. In addition, another ternary system of ACM/CPP with more AO-80 was found to be a very good self-adhesive damping material because of the appearance of a novel transition due to an interfacial layer of ACM/CPP.

  14. Orofacial clinical features in Arnold Chiari type I malformation: A case series.

    de Arruda, José-Alcides; Figueiredo, Eugênia; Monteiro, João-Luiz; Barbosa, Livia-Mirelle; Rodrigues, Cleomar; Vasconcelos, Belmiro

    2018-04-01

    Arnold Chiari malformation (ACM) is characterized by an anatomical defect at the base of the skull where the cerebellum and the spinal cord herniate through the foramen magnum into the cervical spinal canal. Among the subtypes of the condition, ACM type I (ACM-I) is particularly outstanding because of the severity of symptoms. This study aimed to analyze the orofacial clinical manifestations of patients with ACM-I, and discuss their demographic distribution and clinical features in light of the literature. A case series with patients with ACM-I treated between 2012 and 2015 was described. The sample consisted of patients who were referred by the Department of Neurosurgery to the Oral and Maxillofacial Surgery Service of Hospital da Restauração in Brazil for the assessment of facial symptomatology. A questionnaire was applied to evaluate the presence of painful orofacial findings. Data are reported using descriptive statistical methods. Mean patient age was 39.3 years and the sample consisted mostly of male patients. A high prevalence of headache (50%) and pain in the neck (66.7%) and masticatory muscles (50%) was found. Only one patient reported difficulty in performing mandibular movements and two reported jaw clicking sounds. Mean mouth opening was 40.83 mm. ACM-I patients may exhibit orofacial symptoms which may mimic temporomandibular joint disorders. This study brings interesting information that could help clinicians and oral and maxillofacial surgeons to understand this uncommon condition and also help with the diagnosis of patients with similar physical characteristics by referring them to a neurosurgeon. Key words: Arnold-Chiari malformation, facial pain, diagnosis, orofacial.

  15. Cardiovascular Comorbidity and Mortality in Men With Prostate Cancer Treated With Brachytherapy-Based Radiation With or Without Hormonal Therapy

    Nanda, Akash, E-mail: akash.nanda@orlandohealth.com [Department of Radiation Oncology, MD Anderson Cancer Center Orlando, Orlando, Florida (United States); Chen, Ming-Hui [Department of Statistics, University of Connecticut, Storrs, Connecticut (United States); Moran, Brian J.; Braccioforte, Michelle H. [Prostate Cancer Foundation of Chicago, Westmont, Illinois (United States); D' Amico, Anthony V. [Department of Radiation Oncology, Brigham and Women' s Hospital/Dana-Farber Cancer Institute, Boston, Massachusetts (United States)

    2013-04-01

    Purpose: To assess the impact of coronary artery disease (CAD) risk factors and sequelae on the risk of all-cause mortality (ACM) in men treated for prostate cancer (PC). Methods and Materials: The study cohort comprised 5077 men with PC consecutively treated with curative intent between 1997 and 2006 at the Chicago Prostate Cancer Center. Cox and Fine and Gray's competing risks regression multivariable analyses were performed, assessing whether cardiovascular comorbidity impacted the risk of ACM and PC-specific mortality, respectively, adjusting for CAD risk factors (diabetes mellitus, hypercholesterolemia, or hypertension) and sequelae (congestive heart failure or myocardial infarction), age, year and type of treatment, and known PC prognostic factors. Results: When compared with men with no comorbidity there was a significantly increased risk of ACM in men with congestive heart failure or myocardial infarction (adjusted hazard ratio [AHR] 1.96, P<.001) and in men with diabetes mellitus (AHR 1.60, P=.03) and hypertension (AHR 1.25, P=.04). In contrast, men with hypercholesterolemia had a similar risk of ACM (AHR 0.68, P=.17) when compared with men with no comorbidity. Other factors associated with a significantly increased risk of ACM included age (AHR 1.09, P<.001), prostate-specific antigen level (AHR 1.25, P=.008), and Gleason score 8-10 disease (AHR 1.71, P=.003). Cardiovascular comorbidity did not impact the risk of PC-specific mortality. Conclusions: In addition to age and unfavorable PC prognostic factors, select CAD risk factors and sequelae are associated with an increased risk of ACM in men treated for PC. These comorbidity prognostic factors predict time courses of mortality from competing causes, which may be factored into the decision-making process when considering management options for PC in a given individual.

  16. Cardiovascular Comorbidity and Mortality in Men With Prostate Cancer Treated With Brachytherapy-Based Radiation With or Without Hormonal Therapy

    Nanda, Akash; Chen, Ming-Hui; Moran, Brian J.; Braccioforte, Michelle H.; D'Amico, Anthony V.

    2013-01-01

    Purpose: To assess the impact of coronary artery disease (CAD) risk factors and sequelae on the risk of all-cause mortality (ACM) in men treated for prostate cancer (PC). Methods and Materials: The study cohort comprised 5077 men with PC consecutively treated with curative intent between 1997 and 2006 at the Chicago Prostate Cancer Center. Cox and Fine and Gray's competing risks regression multivariable analyses were performed, assessing whether cardiovascular comorbidity impacted the risk of ACM and PC-specific mortality, respectively, adjusting for CAD risk factors (diabetes mellitus, hypercholesterolemia, or hypertension) and sequelae (congestive heart failure or myocardial infarction), age, year and type of treatment, and known PC prognostic factors. Results: When compared with men with no comorbidity there was a significantly increased risk of ACM in men with congestive heart failure or myocardial infarction (adjusted hazard ratio [AHR] 1.96, P<.001) and in men with diabetes mellitus (AHR 1.60, P=.03) and hypertension (AHR 1.25, P=.04). In contrast, men with hypercholesterolemia had a similar risk of ACM (AHR 0.68, P=.17) when compared with men with no comorbidity. Other factors associated with a significantly increased risk of ACM included age (AHR 1.09, P<.001), prostate-specific antigen level (AHR 1.25, P=.008), and Gleason score 8-10 disease (AHR 1.71, P=.003). Cardiovascular comorbidity did not impact the risk of PC-specific mortality. Conclusions: In addition to age and unfavorable PC prognostic factors, select CAD risk factors and sequelae are associated with an increased risk of ACM in men treated for PC. These comorbidity prognostic factors predict time courses of mortality from competing causes, which may be factored into the decision-making process when considering management options for PC in a given individual

  17. MO-F-CAMPUS-I-04: Magnetic Resonance Imaging of An in Vitro 3D Tumor Model

    Veiga, C; Long, T; Siow, B; Loizidou, M; Royle, G; Ricketts, K

    2015-01-01

    Purpose: To investigate the use of an in vitro 3D tumor model (tumoroid) as a bio-phantom for repetitive and sequential magnetic resonance imaging (MRI) studies. Methods: The tissue engineered tumoroid comprised an artificial cancer mass (ACM) containing 30 million HT29 cancer cells seeded in a collagen type I matrix, whose density was increased by plastic compression (dry/wet weight=40%). The ACM was embedded in an uncompressed collagen gel that mimicked the tumor stroma, and the tumoroid was incubated for 24h before imaging. Images were acquired using the 1T ICON™ (Bruker Corporation, Billerica, MA) MRI scanner. T1 maps were calculated using an IR-RARE sequence (TE=12ms, TR=10000ms, 7 inversion times), while for T2 maps a MSME technique (TR=6000ms, 16 echoes) was used. T1 and T2 fittings were performed using a pixel-wise approach to produce relaxometric parametric maps. Results: The images acquired and corresponding T1 and T2 maps indicate contrast between the ACM and the stroma. T1 was 2500 and 2800ms, while T2 was 520 and 760ms, for the ACM and stroma respectively. The ACM construct was not homogenous and internal features were visible, which can be explained by local gradients of cell and/or collagen density. The viability of the cells was confirmed via confocal microscopy for several days after the imaging session, demonstrating the suitability of the tumoroid for sequential imaging studies. Conclusions: We have engineered a tumor model compatible with repetitive and sequential MRI. We found T1 and T2 contrast between the ACM and stroma using a pre-clinical MRI scanner. The model, which enables controllable cell and matrix densities, has potential for a wide range of applications in radiotherapy, such as to study tumor progression and to validate imaging biomarkers. Further work is necessary to understand the mechanisms behind the contrast achieved, and to correlate findings with biology and histology data

  18. MO-F-CAMPUS-I-04: Magnetic Resonance Imaging of An in Vitro 3D Tumor Model

    Veiga, C; Long, T; Siow, B; Loizidou, M; Royle, G; Ricketts, K [University College London, London (United Kingdom)

    2015-06-15

    Purpose: To investigate the use of an in vitro 3D tumor model (tumoroid) as a bio-phantom for repetitive and sequential magnetic resonance imaging (MRI) studies. Methods: The tissue engineered tumoroid comprised an artificial cancer mass (ACM) containing 30 million HT29 cancer cells seeded in a collagen type I matrix, whose density was increased by plastic compression (dry/wet weight=40%). The ACM was embedded in an uncompressed collagen gel that mimicked the tumor stroma, and the tumoroid was incubated for 24h before imaging. Images were acquired using the 1T ICON™ (Bruker Corporation, Billerica, MA) MRI scanner. T1 maps were calculated using an IR-RARE sequence (TE=12ms, TR=10000ms, 7 inversion times), while for T2 maps a MSME technique (TR=6000ms, 16 echoes) was used. T1 and T2 fittings were performed using a pixel-wise approach to produce relaxometric parametric maps. Results: The images acquired and corresponding T1 and T2 maps indicate contrast between the ACM and the stroma. T1 was 2500 and 2800ms, while T2 was 520 and 760ms, for the ACM and stroma respectively. The ACM construct was not homogenous and internal features were visible, which can be explained by local gradients of cell and/or collagen density. The viability of the cells was confirmed via confocal microscopy for several days after the imaging session, demonstrating the suitability of the tumoroid for sequential imaging studies. Conclusions: We have engineered a tumor model compatible with repetitive and sequential MRI. We found T1 and T2 contrast between the ACM and stroma using a pre-clinical MRI scanner. The model, which enables controllable cell and matrix densities, has potential for a wide range of applications in radiotherapy, such as to study tumor progression and to validate imaging biomarkers. Further work is necessary to understand the mechanisms behind the contrast achieved, and to correlate findings with biology and histology data.

  19. [Arnold-Chiari malformation in Noonan syndrome and other syndromes of the RAS/MAPK pathway].

    Ejarque, Ismael; Millán-Salvador, José M; Oltra, Silvestre; Pesudo-Martínez, José V; Beneyto, Magdalena; Pérez-Aytés, Antonio

    2015-05-01

    Noonan syndrome (NS) and other syndromes with a similar phenotype, such as LEOPARD, cardiofaciocutaneous, Costello and Legius, are associated to mutations in genes included in the RAS/MAPK pathway (RASopathies), which is an important signalling pathway related to cell proliferation. Tonsillar descent into the upper cervical spinal canal, known as Arnold-Chiari malformation (ACM), has been reported in patients with NS and this has led some researchers to suggest that ACM could be part of the phenotypic spectrum of NS. We report two cases of NS and ACM. Case 1: 29-year-old female with Noonan phenotype who underwent surgery at the age of nine years due to pulmonary valve stenosis. At the age of 27, she presented symptomatic ACM that required surgical decompression. She presented the c.922A>G (N308D) mutation in the gene PTPN that belongs to the RAS/MAPK pathway. Case 2: a 10-year-old female with Noonan phenotype and asymptomatic ACM detected in magnetic resonance imaging of the brain. She was a carrier of the c.923A>G (N308S) mutation in gene PTPN11. Six patients with this association have been found in the literature, four with the Noonan phenotype and two with LEOPARD. Our two patients provide supplementary evidence that backs up the hypothesis by which ACM would be part of the phenotypic spectrum of NS. The small number of reported cases of patients with this association does not allow us to draw up recommendations about when and how often neuroimaging studies should be performed; a careful neurological examination, however, should be included in the anticipatory health guidelines in syndromes involving the RAS/MAPK pathway.

  20. New technology for fabrication of multifilament NbTi composite

    Yang, Y.K.; Ma, W.M.; Peng, W.N.

    1988-01-01

    Explosive bonding-rolling-drawing process has been developed to produce NbTi multifilamentary superconductors. Multifilamentary wires of 0.5mm in diameter and 2.5km in length with 199 filaments of 25μm in dia. have been produced using this process. The critical current density (Jc) is 1.94x10 5 A/cm 2 at 4.2K and 5T for short samples and 4.9x10 4 A/cm 2 and 4.2/K and 8.5T for the magnet have been reached

  1. Evaluation of Malware Target Recognition Deployed in a Cloud-Based Fileserver Environment

    2012-03-01

    many of these detection techniques could be evaded with simple obfuscation. Kolter and Maloof extend Schultz’s research in [KM04] and [KM06]. Their...69 [KM04] Jeremy Z. Kolter and Marcus A. Maloof. Learning to detect malicious executables in the wild. In Proceedings of the tenth ACM SIGKDD...international conference on Knowledge discovery and data mining, KDD ’04, pages 470–478, New York, NY, USA, 2004. ACM. [KM06] J.Z. Kolter and M.A. Maloof

  2. Progress in the development of BSCCO-2212 superconductors

    Walker, M.S.; Dietderich, D.R.

    1992-11-01

    BSCCO-2212 powders were uniformly dip coated on silver ribbons of 1 meter lengths. Short sample sandwiches of various combinations of silver and the dip coated ribbon were reacted to form possible conductor geometries for characterization and testing. Optical and Scanning Electron Microscope (SEM) examination of surfaces and cross sections showed good but still not ideal microstructure. Representative critical current densities at 6 T and 4.2 K ranged from 8 x 10 3 A/cm 2 for sandwich samples to 2 x 10 4 A/cm 2 for open-faced samples

  3. Preparing superconducting nanopowder based YBCO/Ag tapes

    Paturi, P.; Raittila, J.; Grivel, J.C.

    2002-01-01

    YBCO nanopowder consisting of 1-3 nm thick and 40 nm wide particles has been used to make silver clad superconducting tapes. After annealing in nitrogen at 945 degreesC for 10 h a critical current of 5.02 A (3300 A/cm(2)) was attained, Annealing in mixed atmosphere of oxygen and nitrogen was also...... carried out and this procedure produced tapes with a critical current of 2.83 A (2200 A/cm(2)). These tapes show very good characteristics in magnetic fields. (C) 2002 Elsevier Science B.V. All rights reserved....

  4. GtfA and GtfB Are Both Required for Protein O-Glycosylation in Lactobacillus plantarum

    Lee, I-Chiao; van Swam, Iris I.; Tomita, Satoru; Morsomme, Pierre; Rolain, Thomas; Hols, Pascal; Bron, Peter A.

    2014-01-01

    Acm2, the major autolysin of Lactobacillus plantarum WCFS1, was recently found to be O-glycosylated with N-acetylhexosamine, likely N-acetylglucosamine (GlcNAc). In this study, we set out to identify the glycosylation machinery by employing a comparative genomics approach to identify Gtf1 homologues, which are involved in fimbria-associated protein 1 (Fap1) glycosylation in Streptococcus parasanguinis. This in silico approach resulted in the identification of 6 candidate L. plantarum WCFS1 genes with significant homology to Gtf1, namely, tagE1 to tagE6. These candidate genes were targeted by systematic gene deletion, followed by assessment of the consequences on glycosylation of Acm2. We observed a changed mobility of Acm2 on SDS-PAGE in the tagE5E6 deletion strain, while deletion of other tagE genes resulted in Acm2 mobility comparable to that of the wild type. Subsequent mass spectrometry analysis of excised and in-gel-digested Acm2 confirmed the loss of glycosylation on Acm2 in the tagE5E6 deletion mutant, whereas a lectin blot using GlcNAc-specific succinylated wheat germ agglutinin (sWGA) revealed that besides Acm2, tagE5E6 deletion also abolished all but one other sWGA-reactive, protease-sensitive signal. Only complementation of both tagE5 and tagE6 restored those sWGA lectin signals, establishing that TagE5 and TagE6 are both required for the glycosylation of Acm2 as well as the vast majority of other sWGA-reactive proteins. Finally, sWGA lectin blotting experiments using a panel of 8 other L. plantarum strains revealed that protein glycosylation is a common feature in L. plantarum strains. With the establishment of these enzymes as protein glycosyltransferases, we propose to rename TagE5 and TagE6 as GtfA and GtfB, respectively. PMID:24532775

  5. Abreviaciones utilizadas

    2015-01-01

    AAP: Archivo Arzobispal de Piura. AAT: Archivo Arzobispal de Trujillo ACM: Archivo de la Comunidad de Mórrope. ACMS: Archivo Castillo Muro Sime. A.D.Cj.: Archivo Departamental de Cajamarca. A.D.H.: Archivo Departamental de Huánuco. A.D.L.: Archivo Departamental de Lambayeque. AD.L.L.: Archivo Departamental de La Libertad. A.D.P.: Archivo Departamental de Piura. A.D.T.: Archivo Departamental de Trujillo (La Libertad). A.E.Cj.: Archivo Episcopal de Cajamarca. AFA: Archivo del Fuero Agrario. AFS...

  6. Special issue of Higher-Order and Symbolic Computation

    Danvy, Olivier; Sabry, Amr

    This issue of HOSC is dedicated to the general topic of continuations. It grew out of the third ACM SIGPLAN Workshop on Continuations (CW'01), which took place in London, UK on January 16, 2001 [3]. The notion of continuation is ubiquitous in many different areas of computer science, including...... and streamline Filinski's earlier work in the previous special issue of HOSC (then LISP and Symbolic Computation) that grew out of the first ACM SIGPLAN Workshop on Continuations [1, 2]. Hasegawa and Kakutani's article is the journal version of an article presented at FOSSACS 2001 and that received the EATCS...

  7. Development of a beam current monitor by using an amorphous magnetic core

    Kobayashi, T.; Ueda, T.; Yoshida, Y.; Miya, K.; Tagawa, S.; Kobayashi, H.

    1993-01-01

    The high performance amorphous magnetic core monitor (ACM) for the measurement of electron beam currents has been developed. This monitor is composed of an amorphous magnetic core, radiation shields, a winding, magnetic absorbers, a ceramic vacuum duct and a SMA connecter. The ACM showed the very fast rise and fall times (< 1 ns), the high sensitivity (5 V/A at 50 Ω load), the good linearity, and good S/N ratio due to the high permeability of the amorphous magnetic core. The monitor works as a primary transformer. The time-response was simulated by an electric circuit analysis code. (orig.)

  8. Protective effect of astrocyte-conditioned medium on neurons following hypoxia and mechanical injury

    YAN Ji-wen

    2013-02-01

    Full Text Available 【Abstract】Objective: To investigate the protec-tive effect of mouse astrocyte-conditioned medium (ACM on hypoxic and mechanically injured neurons by a cell model in vitro, and to explore the possible mechanism. Methods: The model of hypoxic neuronal injury was caused by 3% O 2 in three-gas incubator. Neurons were cul-tured with ordinary medium or 20% ACM respectively and randomly divided into hypoxic group (hypoxia for 4, 8, 24 h and marked as H4R0, H8R0, H24R0 and hypoxia reoxygenation group (H4R24, H8R24, H24R24. Mechanical injury model was developed by scratching neurons cultured in 20% ACM or ordinary medium to different degrees. Neu-rons in both medium were divided into normal control group, mild, moderate and severe injury groups. The 20% ACM was added 24 h before hypoxia/reoxygenation or mechanical injury. The morphology and survival of neurons were observed and counted by trypan blue staining. The concentration of NO, lactic dehydrogenase (LDH and membrane ATPase activity were detected by corresponding kits. Results: It was showed that 20% ACM can obviously promote the survival rate of hypoxia/reoxygenated neurons and scratched neurons as well. The morphology and num-ber of neurons exposed to hypoxia or scratch injury showed great difference between groups with or without ACM treatment. Compared with control group, the concentration of NO and LDH was much lower in hypoxic/reoxygenated neurons treated with 20% ACM, and the ATPase activity was higher. For the mechanical injury model, neurons with moderate injury also revealed a lower NO and LDH concen-tration than the control group. All the differences were sta-tistically significant (P<0.05. Conclusion: ACM can promote the survival and func-tional recovery of neurons following hypoxia or scratching to a certain degree. The mechanism may be associated with reducing the synthesis and release of NO and LDH as well as increasing the activity of membrane ATPase. Key words: Glial cell line

  9. Risk prediction in stable cardiovascular disease using a high-sensitivity cardiac troponin T single biomarker strategy compared to the ESC-SCORE.

    Biener, Moritz; Giannitsis, Evangelos; Kuhner, Manuel; Zelniker, Thomas; Mueller-Hennessen, Matthias; Vafaie, Mehrshad; Stoyanov, Kiril M; Neumann, Franz-Josef; Katus, Hugo A; Hochholzer, Willibald; Valina, Christian Marc

    2018-01-01

    To evaluate the prognostic performance of high-sensitivity cardiac troponin T (hs-cTnT) compared with the ESC-SCORE. We included low-risk outpatients with stable cardiovascular (CV) disease categorised into need for non-secondary and secondary prevention. The prognostication of hs-cTnT at index visit was compared with the European Society of Cardiology-Systematic COronary Risk Evaluation (ESC-SCORE) with respect to all-cause mortality (ACM) and two composite endpoints (ACM, acute myocardial infarction (AMI) and stroke and ACM, AMI, stroke and rehospitalisation for acute coronary syndrome (ACS) and decompensated heart failure (DHF)). Within a median follow-up of 796 days, a total of 16 deaths, 32 composite endpoints of ACM, AMI and stroke and 83 composite endpoints of ACM, AMI, stroke, rehospitalisation for ACS and DHF were observed among 693 stable low-risk outpatients. Using C-statistics, measurement of hs-cTnT alone outperformed the ESC-SCORE for the prediction of ACM in the entire study population (Δarea under the curve (AUC) 0.221, p=0.0039) and both prevention groups (non-secondary: ΔAUC 0.164, p=0.0208; secondary: ΔAUC 0.264, p=0.0134). For the prediction of all other secondary endpoints, hs-cTnT was at least as effective as the ESC-SCORE, both in secondary and non-secondary prevention. Using continuous and categorical net reclassification improvement and integrated discrimination improvement, hs-cTnT significantly improved reclassification regarding all endpoints in the entire population and in the secondary prevention cohort. In non-secondary prevention, hs-cTnT improved reclassification only for ACM. The results were confirmed in an independent external cohort on 2046 patients. Hs-cTnT is superior to the multivariable ESC-SCORE for the prediction of ACM and a composite endpoint in stable outpatients with and without relevant CV disease. NCT01954303; Pre-results.

  10. Development of Axial Continuous Metal Expeller for melt conditioning of alloys

    Cassinath, Z.; Prasada Rao, A.K.

    2016-01-01

    ACME (Axial, centrifugal metal expeller) is a novel processing technology developed independently for conditioning liquid metal prior to solidification processing. The ACME process is based on an axial compressor and uses a rotor stator mechanism to impose a high shear rate and a high intensity of turbulence to the liquid metal, so that the conditioned liquid metal has uniform temperature and uniform chemical composition as it is expelled. The microstructural refinement is achieved through the process of dendrite fragmentation while taking advantage of the thixotropic property of semisolid metal slurry so that it can be conveyed for further downstream operations. This paper introduces the concept and its advantages over current technologies. (paper)

  11. Database Publication Practices

    Bernstein, P.A.; DeWitt, D.; Heuer, A.

    2005-01-01

    There has been a growing interest in improving the publication processes for database research papers. This panel reports on recent changes in those processes and presents an initial cut at historical data for the VLDB Journal and ACM Transactions on Database Systems.......There has been a growing interest in improving the publication processes for database research papers. This panel reports on recent changes in those processes and presents an initial cut at historical data for the VLDB Journal and ACM Transactions on Database Systems....

  12. Diagnóstico não invasivo da anemia fetal pela medida do pico de velocidade sistólica na dopplervelocimetria da artéria cerebral média Noninvasive fetal anemia diagnosis by middle cerebral artery peak systolic velocity waveform measurement

    Marcos Roberto Taveira; Antônio Carlos Vieira Cabral; Henrique Vítor Leite; Isabela Gomes de Melo; Ana Paula Brum de Miranda Lopes

    2004-01-01

    OBJETIVO: avaliar se existe associação entre a medida do pico de velocidade sistólica (PVS) na dopplervelocimetria da artéria cerebral média (ACM) e a concentração de hemoglobina fetal e determinar a sua capacidade diagnóstica. MÉTODOS: entre janeiro de 2000 e maio de 2003, 44 gestantes isoimunizadas foram submetidas a transfusão intra-uterina. Realizou-se estudo dopplervelocimétrico da ACM antes de cada transfusão fetal, sempre com intervalo inferior a 3 horas, antecedendo o procedimento. O ...

  13. Predicting E-commerce Consumer Behaviour Using Sparse Session Data

    Thorrud, Thorstein Kaldahl; Myklatun, Øyvind

    2015-01-01

    This thesis research consumer behavior in an e-commerce domain by using a data set of sparse session data collected from an anonymous European e-commerce site. The goal is to predict whether a consumer session results in a purchase, and if so, which items are purchased. The data is supplied by the ACM Recommender System Challenge, which is a yearly challenge held by the ACM Recommender System Conference. Classification is used for predicting whether or not a session made a purchase, as w...

  14. Development of Axial Continuous Metal Expeller for melt conditioning of alloys

    Cassinath, Z.; Prasada Rao, A. K.

    2016-02-01

    ACME (Axial, centrifugal metal expeller) is a novel processing technology developed independently for conditioning liquid metal prior to solidification processing. The ACME process is based on an axial compressor and uses a rotor stator mechanism to impose a high shear rate and a high intensity of turbulence to the liquid metal, so that the conditioned liquid metal has uniform temperature and uniform chemical composition as it is expelled. The microstructural refinement is achieved through the process of dendrite fragmentation while taking advantage of the thixotropic property of semisolid metal slurry so that it can be conveyed for further downstream operations. This paper introduces the concept and its advantages over current technologies.

  15. InAs/GaAs quantum dot lasers with InGaP cladding layer grown by solid-source molecular-beam epitaxy

    Yeh, N.-T.; Liu, W.-S.; Chen, S.-H.; Chiu, P.-C.; Chyi, J.-I.

    2002-01-01

    This letter presents the lasing properties of InAs/GaAs quantum dot lasers with InGaP cladding layers grown by solid-source molecular-beam epitaxy. These Al-free lasers exhibit a threshold current density of 138 A/cm 2 , an internal loss of 1.35 cm -1 , and an internal quantum efficiency of 31% at room temperature. At a low temperature, a very high characteristic temperature of 425 K and very low threshold current density of 30 A/cm 2 are measured

  16. Study of a very low cost air combat maneuvering trainer aircraft

    Hill, G. C.; Bowles, J. V.

    1976-01-01

    A very low cost aircraft for performing Air Combat Maneuvering (ACM) training was studied using the BD-5J sport plane as a point of departure. The installation of a larger engine and increased fuel capacity were required to meet the performance and mission objectives. Reduced wing area increased the simulation of the ACM engagement, and a comparison with current tactical aircraft is presented. Other factors affecting the training transfer are considered analytically, but a flight evaluation is recommended to determine the concept utility.

  17. 40 CFR 180.555 - Trifloxystrobin; tolerances for residues.

    2010-07-01

    ... Horse, meat 0.1 Horse, meat byproducts 0.1 Leaf petioles subgroup 4B 3.5 Mango 0.7 Milk 0.02 Nut, tree..., straw 5.0 1 There are no U.S. registrations as of September 27, 1999 for use on banana. (b) Section 18...

  18. 75 FR 3190 - Endangered and Threatened Wildlife and Plants; Initiation of Status Review for Agave eggersiana

    2010-01-20

    ... Supervisor, Caribbean Ecological Services Field Office , P.O. Box 491, Boquero, Puerto Rico 00622, by... educational purposes; (c) Disease or predation; (d) The inadequacy of existing regulatory mechanisms; or (e... Ecological Services Field Office (see FOR FURTHER INFORMATION CONTACT). Background Section 4(b)(3)(B) of the...

  19. AcEST: BP915397 [AcEST

    Full Text Available UPTR Putative uncharacterized protein OS=Cupriavidus taiwanensis (strain R1 / LMG...Cupri... 33 9.9 >tr|B3R9M4|B3R9M4_CUPTR Putative uncharacterized protein OS=Cupriavidus taiwanensis (strain

  20. The study of conjugation of anti-CD20 monoclonal antibody for labeling with metallic or lanthanides radionuclides

    Akanji, Akinkunmi Ganiyu

    2012-01-01

    Lymphomas are malignancies or cancers that start from the malign transformation of a lymphocyte in the lymphatic system. Generally, lymphomas start from the lymph nodes or from the agglomeration of the lymphatic tissues, organs like stomach, intestines, in some cases it can involve the bone marrow and the blood, it can also disseminate to other organs. Lymphomas are divided in two major categories: Hodgkin lymphoma and non-Hodgkin lymphoma (NHL). Patient with NHL are generally treated with radiotherapy alone or combined with immunotherapy using monoclonal antibody rituximab (MabThera®). Currently, monoclonal antibodies (Acm) conjugated with bifunctional chelate agents and radiolabeled with metallic or lanthanides radionuclides are a treatment reality for patients with NHL by the principle of radioimmunotherapy (RIT). This study focused on the conditions of conjugation of Acm rituximab (MabThera®) with bifunctional chelating agents DOTA and DTPA. Various parameters were studied: method of Acm purification, conditions of Acm conjugation, the method for determination of number of chelate agent coupled to the Acm, method for purification of the conjugated antibody Acm, conditions of labeling of the conjugated antibody with lutetium-177, method of purification of the radiolabeled immuno conjugate, method of radiochemical purity (RP), specific binding in vitro Raji cells (Human Burkitt) and biological distribution performed in normal Balb-c mouse. The three methodologies employed in pre-purification of Acm (dialysis, size exclusion chromatograph and dial filtration) demonstrated to be efficient; they provided sample recovery exceeding 90%. However, the methodology of dial filtration presents minimal sample loss, and gave the final recovery of the sample in micro liters; thereby facilitating sample use in subsequent experiments. Numbers of chelators attached to the Acm molecule was proportional to the molar ratio studied. When we evaluated the influence of different

  1. The study of conjugation of anti-CD20 monoclonal antibody for labeling with metallic or lanthanides radionuclides; Estudo de conjugacao do anticorpo anti-CD20 para marcacao com radionuclideos metalicos ou lantanideos

    Akanji, Akinkunmi Ganiyu

    2012-07-01

    Lymphomas are malignancies or cancers that start from the malign transformation of a lymphocyte in the lymphatic system. Generally, lymphomas start from the lymph nodes or from the agglomeration of the lymphatic tissues, organs like stomach, intestines, in some cases it can involve the bone marrow and the blood, it can also disseminate to other organs. Lymphomas are divided in two major categories: Hodgkin lymphoma and non-Hodgkin lymphoma (NHL). Patient with NHL are generally treated with radiotherapy alone or combined with immunotherapy using monoclonal antibody rituximab (MabThera Registered-Sign ). Currently, monoclonal antibodies (Acm) conjugated with bifunctional chelate agents and radiolabeled with metallic or lanthanides radionuclides are a treatment reality for patients with NHL by the principle of radioimmunotherapy (RIT). This study focused on the conditions of conjugation of Acm rituximab (MabThera Registered-Sign ) with bifunctional chelating agents DOTA and DTPA. Various parameters were studied: method of Acm purification, conditions of Acm conjugation, the method for determination of number of chelate agent coupled to the Acm, method for purification of the conjugated antibody Acm, conditions of labeling of the conjugated antibody with lutetium-177, method of purification of the radiolabeled immuno conjugate, method of radiochemical purity (RP), specific binding in vitro Raji cells (Human Burkitt) and biological distribution performed in normal Balb-c mouse. The three methodologies employed in pre-purification of Acm (dialysis, size exclusion chromatograph and dial filtration) demonstrated to be efficient; they provided sample recovery exceeding 90%. However, the methodology of dial filtration presents minimal sample loss, and gave the final recovery of the sample in micro liters; thereby facilitating sample use in subsequent experiments. Numbers of chelators attached to the Acm molecule was proportional to the molar ratio studied. When we evaluated

  2. 48 CFR 301.607-77 - Governance.

    2010-10-01

    ... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Governance. 301.607-77 Section 301.607-77 Federal Acquisition Regulations System HEALTH AND HUMAN SERVICES GENERAL HHS... Governance. The Departmental ACM, in ASFR/OGAPA/DA, serves as the Departmental FAC-P/PM Program Manager and...

  3. On the Integration of Medium Wave Infrared Cameras for Vision-Based Navigation

    2015-03-01

    almost negligible detection by EO cameras in the dark . In order to compare the estimated SfM trajectories, the point clouds created by VisualSFM for...IEEE, 2000. [14] Noah Snavely, Steven M Seitz, and Richard Szeliski. Photo tourism : exploring photo collections in 3d. In ACM transactions on graphics

  4. Autolysis of Lactococcus lactis is influenced by proteolysis

    Buist, G; Venema, G; Kok, J.

    1998-01-01

    The autolysin AcmA of Lactococcus lactis was shown to be degraded by the extracellular Lactococcal proteinase PrtP. Autolysis, as evidenced by reduction in optical density of a stationary-phase culture and concomitant release of intracellular proteins, was greatly reduced when L. lactis MG1363 cells

  5. Expression of prophage-encoded endolysins contributes to autolysis of Lactococcus lactis

    Visweswaran, Ganesh Ram R.; Kurek, Dorota; Szeliga, Monika; Pastrana, Francisco Romero; Kuipers, Oscar P.; Kok, Jan; Buist, Girbe

    Analysis of autolysis of derivatives of Lactococcus lactis subsp. cremoris MG1363 and subsp. lactis IL1403, both lacking the major autolysin AcmA, showed that L. lactis IL1403 still lysed during growth while L. lactis MG1363 did not. Zymographic analysis revealed that a peptidoglycan hydrolase

  6. Precipitation collector bias and its effects on temporal trends and spatial variability in National Atmospheric Deposition Program/National Trends Network data

    Wetherbee, Gregory A.

    2017-01-01

    Precipitation samples have been collected by the National Atmospheric Deposition Program's (NADP) National Trends Network (NTN) using the Aerochem Metrics Model 301 (ACM) collector since 1978. Approximately one-third of the NTN ACM collectors have been replaced with N-CON Systems, Inc. Model ADS 00-120 (NCON) collectors. Concurrent data were collected over 6 years at 12 NTN sites using colocated ACM and NCON collectors in various precipitation regimes. Linear regression models of the colocated data were used to adjust for relative bias between the collectors. Replacement of ACM collectors with NCON collectors resulted in shifts in 10-year seasonal precipitation-weighted mean concentration (PWMC) trend slopes for: cations (−0.001 to −0.007 mgL−1yr−1), anions (−0.009 to −0.028 mgL−1yr−1), and hydrogen ion (+0.689 meqL-1yr−1). Larger shifts in NO3− and SO4−2 seasonal PWMC trend slopes were observed in the Midwest and Northeast US, where concentrations are generally higher than in other regions. Geospatial analysis of interpolated concentration rasters indicated regions of accentuated variability introduced by incorporation of NCON collectors into the NTN.

  7. A Logic for Reasoning About Time-Dependent Access Control Policies

    2008-05-20

    its purpose, it is a rather coarse approximation of the behavior desired in general. It is likely that Alice wants the credential C to allow Bob...Jacob Strauss, Robert Morris, and M. Frans Kaashoek. Alpaca : Extensible authorization for distributed services. In Proceedings of the 14th ACM Conference

  8. Cryptography: It’s Not Just For Electronic Mail Anymore

    1993-03-01

    David Chaum . Security without identification: Transaction systems to make big brother obsolete. Communications of the ACM, 28(10): 1030-1044, Oc- tober...Jeannette Wing, Maurice Herlihy, Stewart Clamen, David Detlefs, Karen Kietzke, Richard Lerner, and Su-Yuen Ling. The Avalon language: A tutorial

  9. Toward Practical Verification of Outsourced Computations Using Probabilistically Checkable Proofs (PCPs)

    2010-07-12

    Germany, 1999. [8] L. Babai, L. Fortnow, L. A. Levin, and M. Szegedy. Checking Computations in Polylogarithmic Time. In STOC, 1991. [9] A. Ben- David ...their work. J. ACM, 42(1):269–291, 1995. [12] D. Chaum , C. Crépeau, and I. Damgard. Multiparty unconditionally secure protocols. In STOC, 1988. [13

  10. Service-Oriented Access Control

    2014-09-01

    root bridge for each VLAN, all such that traffic cost is minimized. Sung et al. define this cost as the sum of broadcast traffic, inter-VLAN data...Merlin,” in Proc. 12th ACM Workshop on Hot Topics in Networks, College Park, MD, 2013, pp. 24:1–24:7. [10] A. Voellmy and P. Hudak, “ Nettle : Taking the

  11. Using Active Networking to Detect and Troubleshoot Issues in Tactical Data Networks

    2014-06-01

    networking (SDN) paradigm, which has gained popularity in recent years, has its roots in the idea of programmable networks [6]. By extending the...278–289, Aug. 2011. 67 [13] M. Hicks, P. Kakkar, J. T. Moore, C. A. Gunter, and S. Nettles , “Plan: A programming language for active networks,” ACM

  12. Information workers and their personal information management: a literature review

    A.A.J. (Jos) van Helvoort

    2011-01-01

    The research described in this paper provides insights into tools and methods which are used by professional information workers to keep and to manage their personal information. A literature study was carried out on 23 scholar papers and articles, retrieved from the ACM Digital Library and Library

  13. Safety in Numbers

    2010-11-27

    Bicocca. Dipartimento di Informatica , Sistemistica e Comunicazione. Laboratorio di Test e Analisi del Software, Milano. Technical Report LTA:2004:05...Communications of the ACM, 1981. 24(9): pp. 563-573. 76. Thomas Reps, On the sequential nature of interprocedural program-analysis problems. Acta Informatica

  14. NCBI nr-aa BLAST: CBRC-MMUR-01-1553 [SEVENS

    Full Text Available CBRC-MMUR-01-1553 ref|YP_002554277.1| signal recognition particle-docking protein F...tsY [Diaphorobacter sp. TPSY] gb|ACM34277.1| signal recognition particle-docking protein FtsY [Diaphorobacter sp. TPSY] YP_002554277.1 0.49 30% ...

  15. Long Term Stability Investigation of Solid Oxide Electrolysis Cell with Infiltrated Porous YSZ Air Electrode Under High Current

    Veltzé, Sune; Ovtar, Simona; Simonsen, Søren Bredmose

    2015-01-01

    stabilised zirconia (YSZ) backbone air electrode and Ni/YSZ cermet fuel electrode. The SOC was tested at electrolysis conditions under high current (up to -1 A/cm2). The porous YSZ electrodes was infiltrated with gadolinium-doped ceria oxide (CGO), to act as a barrier layer between the catalyst...

  16. Seeking Balance in Cyber Education

    2015-02-01

    to be practical today. It is true that some computer systems have been developed with provable security in mind. For example, seL4 is a microkernel...Aug. 2014. <http://nvd.nist.gov/home.cfm>. 6. Klein, Gerwin, et al. “ seL4 : Formal verification of an OS kernel.” Proceedings of the ACM SIGOPS

  17. Electron beam initiated modification of acrylic elastomer in presence of polyfunctional monomers

    Vijayabaskar, V.; Bhattacharya, S.; Tikku, V.K.; Bhowmick, A.K.

    2004-01-01

    The structural changes of an acrylic rubber (ACM) in presence and absence of polyfunctional monomers like trimethylolpropane triacrylate, tripropyleneglycol diacrylate, trimethylolmethane tetraacrylate and trimethylolpropane trimethacrylate at different doses of electron beam (EB) irradiations were investigated with the help of FTIR spectroscopy (in the attenuated total reflectance mode) and sol-gel analysis. As the radiation dose increases, the concentration of carbonyl group increases in the ACM rubber due to aerial oxidation. This is corroborated from the increase in the absorbance values at 1734 and 1160 cm -1 , which are due to carbonyl and C-O-C stretching frequencies, respectively. The increase in crosslinking is revealed by the increase in percentage gel content with radiation dose. The lifetime of spurs formed and the critical dose, an important criterion for overlapping of spurs have been determined for both grafted and ungrafted ACM rubber using a mathematical model. The predominance of crosslinking by electronic stopping with energetic EB projectile and the increase in effective radius of crosslinking have also been verified by this model. The doses at which the synergistic occurrence of both dislinking and endlinking steps originate have been calculated using linear energy transfer of EB. The ratio of scissioning to crosslinking for ACM rubber has been determined by using Charlesby-Pinner equation. The mechanical properties have been studied for different modified and unmodified systems and the tensile strength is found to increase with grafting of polyfunctional monomers

  18. NCBI nr-aa BLAST: CBRC-TSYR-01-0087 [SEVENS

    Full Text Available CBRC-TSYR-01-0087 ref|YP_002550227.1| ice nucleation protein [Agrobacterium vitis S4] gb|ACM37217.1| ice nuc...leation protein [Agrobacterium vitis S4] YP_002550227.1 8e-16 19% ...

  19. Characteristics of an activated carbon monolith for a helium adsorption compressor

    Lozano-Castello, D.; Jorda-Beneyto, M.; Cazorla-Amoros, D.; Linares-Solano, A.; Burger, Johannes Faas; ter Brake, Hermanus J.M.; Holland, Herman J.

    2010-01-01

    An activated carbon monolith (ACM) with a high helium adsorption/desorption capacity, high density, low pressure drop, low thermal expansion and good mechanical properties was prepared and applied successfully in a helium adsorption compressor as a part of a 4.5 K sorption cooler. The activated

  20. High current density in bulk YBa2Cu3O/sub x/ superconductor

    Salama, K.; Selvamanickam, V.; Gao, L.; Sun, K.

    1989-01-01

    A liquid phase processing method for the fabrication of bulk YBa 2 Cu 3 O/sub x/ superconductors with large current carrying capacity has been developed. Slow cooling through the peritectic transformation (1030--980 degree C) has been shown to control the microstructure of these superconductors. A cooling rate of 1 degree C/h in this temperature range has yielded a microstructure with long plate type, thick grains oriented over a wide area. Current density up to 18 500 A/cm 2 has been obtained by continuous direct current measurements and in excess of 62 000 A/cm 2 with pulse current of 10 ms duration and 75 000 A/cm 2 using 1 ms pulse. The strong magnetic field dependence observed in sintered bulk 1-2-3 superconductors is also minimized to a large extent where a current density in excess of 37 000 A/cm 2 is obtained in a field of 6000 G

  1. Compared With Usual Sodium Intake, Low- and Excessive-Sodium Diets Are Associated With Increased Mortality

    Graudal, Niels; Jürgens, Gesche; Baslund, Bo

    2014-01-01

    BACKGROUND: The effect of sodium intake on population health remains controversial. The objective was to investigate the incidence of all-cause mortality (ACM) and cardiovascular disease events (CVDEs) in populations exposed to dietary intakes of low sodium (<115 mmol), usual sodium (low usual so...

  2. Proceeding of the 1999 Particle Accelerator Conference. Volume 3

    1999-04-02

    Saitama, JAPAN Abstract The maximum emision current density is also reduced from 5.1 to 3.15 A/cm2 . We plan to use an Ir-coated An electron cooler (EC...3687, 3693 Sutton, Terry D. 3597 Tatanov, V.I. 753 Spyropoulos, Basile 2543 Suwada, T. 1132 Tavares, Pedro F. 2421, 2894, 3125 Sredniawski, Joseph 587

  3. Les Africaines Et Les Tic

    Enquête sur les technologies, la question de genre et autonomisation ...... Polachek, S. (1981) «Occupational self-selection: a human capital approach to sex ...... in the Computer Science major », Communications of the ACM, 44(5) : 108–14.

  4. OCP: Opportunistic Carrier Prediction for Wireless Networks

    2008-08-01

    Many protocols have been proposed for medium access control in wireless networks. MACA [13], MACAW [3], and FAMA [8] are the earlier proposals for...world performance of carrier sense. In Proceedings of ACM SIGCOMM E-WIND Workshop, 2005. [13] P. Karn. MACA : A new channel access method for packet radio

  5. Effects of accelerated closing of the five oldest coal-fired power plants [in the Netherlands]; Effecten van versneld sluiten van de vijf oudste kolencentrales

    Seebregts, A.J. [ECN Beleidsstudies, Amsterdam (Netherlands)

    2013-09-15

    This memo outlines the possible effects of the early closing of the five oldest coal-fired power plants in the Netherlands, as part of the Dutch Energy Agreement, still to be concluded at this time. It concerns plants from four power producers: RWE/Essent, E.ON, GDF Suez Netherlands and EPZ. The decision or the agreement to reduce coal capacity is likely to affect prices in the Dutch electricity market. The Authority for Consumers and Markets (ACM) must make a judgment about the possible adverse effect within the framework of the (European) cartel legislation. By order of ACM the author has carried out several calculations of which the results and starting points of the calculations are summarized in this paper [Dutch] Deze notitie schetst de mogelijke effecten van het vervroegd sluiten van de vijf oudste kolencentrales in Nederland, als onderdeel van het nog te sluiten Energieakkoord. Het betreft centrales van vier producenten: RWE/Essent, E.ON, GDF Suez Nederland en EPZ. Het besluit c.q. de afspraak om kolenvermogen uit de markt te halen heeft mogelijk invloed op de prijzen op de Nederlandse elektriciteitsmarkt. De ACM moet een oordeel vellen over de mogelijke ongewenstheid van dat effect in het kader van de (Europese) kartelwetgeving. Om een indicatie te krijgen van de effecten, heeft de ACM aan ECN gevraagd een aantal berekeningen uit te voeren. De resultaten en de uitgangspunten van deze berekeningen staan in deze notitie samengevat.

  6. Retweeting Activity on Twitter: Signs of Deception

    2015-05-22

    for computing the like- lihood of an unknown user being a human, bot or cyborg . [16] shows the strong classification and prediction performance of...ACM (2013) 2. Chu, Z., et al.: Who is Tweeting on Twitter: Human, Bot, or Cyborg ? ACSAC, 21–30 (2010) 3. Derrida, B., et al.: Statistical Properties

  7. Breaking the current density threshold in spin-orbit-torque magnetic random access memory

    Zhang, Yin; Yuan, H. Y.; Wang, X. S.; Wang, X. R.

    2018-04-01

    Spin-orbit-torque magnetic random access memory (SOT-MRAM) is a promising technology for the next generation of data storage devices. The main bottleneck of this technology is the high reversal current density threshold. This outstanding problem is now solved by a new strategy in which the magnitude of the driven current density is fixed while the current direction varies with time. The theoretical limit of minimal reversal current density is only a fraction (the Gilbert damping coefficient) of the threshold current density of the conventional strategy. The Euler-Lagrange equation for the fastest magnetization reversal path and the optimal current pulse is derived for an arbitrary magnetic cell and arbitrary spin-orbit torque. The theoretical limit of minimal reversal current density and current density for a GHz switching rate of the new reversal strategy for CoFeB/Ta SOT-MRAMs are, respectively, of the order of 105 A/cm 2 and 106 A/cm 2 far below 107 A/cm 2 and 108 A/cm 2 in the conventional strategy. Furthermore, no external magnetic field is needed for a deterministic reversal in the new strategy.

  8. What is Genselfdual?

    Bouyukliev, Iliya; Bouyuklieva, Stefka; Dzhumalieva-Stoeva, Maria; Monev, Venelin

    2016-01-01

    This paper presents developed software in the area of Coding Theory. Using it, all binary self-dual codes with given properties can be classified. The programs have consequent and parallel implementations. ACM Computing Classification System (1998): G.4, E.4.

  9. Radioprotective Effect of Achillea millefolium L Against Genotoxicity Induced by Ionizing Radiation in Human Normal Lymphocytes

    Somayeh Shahani

    2015-04-01

    Full Text Available The radioprotective effect of Achillea millefolium L (ACM extract was investigated against genotoxicity induced by ionizing radiation (IR in human lymphocytes. Peripheral blood samples were collected from human volunteers and incubated with the methanolic extract of ACM at different concentrations (10, 50, 100, and 200 μg/mL for 2 hours. At each dose point, the whole blood was exposed in vitro to 2.5 Gy of X-ray and then the lymphocytes were cultured with mitogenic stimulation to determine the micronuclei in cytokinesis-blocked binucleated cell. Antioxidant capacity of the extract was determined using free radical-scavenging method. The treatment of lymphocytes with the extract showed a significant decrease in the incidence of micronuclei binucleated cells, as compared with similarly irradiated lymphocytes without any extract treatment. The maximum protection and decrease in frequency of micronuclei were observed at 200 μg/mL of ACM extract which completely protected genotoxicity induced by IR in human lymphocytes. Achillea millefolium extract exhibited concentration-dependent radical-scavenging activity on 1,1-diphenyl-2-picryl hydrazyl free radicals. These data suggest that the methanolic extract of ACM may play an important role in the protection of normal tissues against genetic damage induced by IR.

  10. Decomposition of Some Well-Known Variance Reduction Techniques. Revision.

    1985-05-01

    34use a family of transformatlom to convert given samples into samples conditioned on a given characteristic (p. 04)." Dub and Horowitz (1979), Granovsky ...34Antithetic Varlates Revisited," Commun. ACM 26, 11, 064-971. Granovsky , B.L. (1981), "Optimal Formulae of the Conditional Monte Carlo," SIAM J. Alg

  11. Adaptive Modeling of Details for Physically-Based Sound Synthesis and Propagation

    2015-03-21

    CONTENTS LIST OF TABLES...Rauber, A., and Merkl, D. (2002). Content -based organization and visualization of music archives. In Proceedings of the tenth ACM international...Interactive simulation of complex audiovisual scenes. Presence: Teleoper. Virtual Environ., 13:99–111. van den Doel, K., Kry, P., and Pai, D. (2001

  12. Supercapacitive performance of hydrous ruthenium oxide (RuO2 ...

    2016-08-26

    SO4 electrolyte. RuO2.H2O film showed maximum specific capacitance of 192 F.g-1 at a scan rate of 20 mV.s-1. The charge–discharge studies of RuO2.H2O carried out at 300 A.cm-2 current density revealed the specific ...

  13. High performance tunnel injection InGaN/GaN quantum Dot light emitting diodes emitting in the green (λ=495nm)

    Zhang, Meng; Banerjee, Animesh; Bhattacharya, Pallab

    2011-01-01

    peak at 495 nm at 300 K. The characteristics of tunnel injection InGaN/GaN quantum dot light emitting diodes are presented. The current density at maximum efficiency is 90.2 A/cm 2, which is superior to equivalent multiquantum well devices. © 2010

  14. Steve Jobs and the User Psyche

    Denning, Peter J.

    2011-01-01

    The article of record as published may be found at http://dx.doi.org/10.1145/2043155.2043157 Peter J. Denning reflects on a meeting he had with Steve Jobs in 1988. Published in ACM Ubiquity.Ubiquity Commentary

  15. Knowledge and use of asthma control measurement tools in the ...

    Objective: To investigate the knowledge and use of asthma control measurement (ACM) tools in the management of asthma among doctors working in family and internal medicine practice in Nigeria. Method: A questionnaire based on the global initiative on asthma (GINA) guideline was self-administered by 194 doctors.

  16. The application of wireless sensor networks and wearable technologies for educational purposes: A scoping review

    Iyawa, GE

    2017-11-01

    Full Text Available which adopted four academic databases: ACM, IEEE Xplore, ScienceDirect and Springer Link. In total, seven publications were identified based on the inclusion and exclusion criteria. The scoping review identified the extent and range of studies which have...

  17. Automated Security Testing of Web Widget Interactions

    Bezemer, C.P.; Mesbah, A.; Van Deursen, A.

    2009-01-01

    This paper is a pre-print of: Cor-Paul Bezemer, Ali Mesbah, and Arie van Deursen. Automated Security Testing of Web Widget Interactions. In Proceedings of the 7th joint meeting of the European Software Engineering Conference and the ACM SIGSOFT Symposium on the Foundations of Software Engineering

  18. Architecture Support for Runtime Integration and Verification of Component-based Systems of Systems

    Gonzalez, A.; Piel, E.; Gross, H.G.

    2008-01-01

    Preprint of paper published in: ASE 2008 - 23rd IEEE/ACM International Conference on Automated Software Engineering, 15-19 September 2008; doi:10.1109/ASEW.2008.4686292 Systems-of-Systems (SoS) represent a novel kind of system, for which runtime evolution is a key requirement, as components join and

  19. 77 FR 51067 - Investigations Regarding Eligibility To Apply for Worker Adjustment Assistance

    2012-08-23

    .... Brockport, PA...... 08/06/12 08/03/12 (Union). 81863 Industrial Machine & Farmington, MO..... 08/07/12 08/07... Industrial Sales (Workers). 81865 Sihi Pumps (Workers).... Grand Island, NY... 08/07/12 07/31/12 81866 Acme... Custom Technology, Windsor, CT........ 08/09/12 08/09/12 Inc., Engineering Design and Drafting Department...

  20. A Cellular Automata Approach to Computer Vision and Image Processing.

    1980-09-01

    the ACM, vol. 15, no. 9, pp. 827-837. [ Duda and Hart] R. 0. Duda and P. E. Hart, Pattern Classification and Scene Analysis, Wiley, New York, 1973...Center TR-738, 1979. [Farley] Arthur M. Farley and Andrzej Proskurowski, "Gossiping in Grid Graphs", University of Oregon Computer Science Department CS-TR

  1. NCBI nr-aa BLAST: CBRC-MMUR-01-1593 [SEVENS

    Full Text Available CBRC-MMUR-01-1593 ref|YP_002522550.1| putative dehydrogenase [Thermomicrobium roseu...m DSM 5159] gb|ACM05630.1| putative dehydrogenase [Thermomicrobium roseum DSM 5159] YP_002522550.1 3.4 34% ...

  2. Formation and characterization of Y : 247 film through spray ...

    Unknown

    gions (< 50 Å) of minority Y : 124 phase and stacking faults capable of ... critical current density (Jc) for Y : 247 films is ~ 103 A/cm2, and with silver ..... biphasic. As a result of decomposition, Y : 247 may be partially converted into Y : 124.

  3. After Action Report: Cursor On Target International User Group Meeting (2nd). Held on 1-2 April 2014

    2014-04-01

    is ready access to the cafeteria and Starbucks coffee bar in an area where all can travel without escort. Use of the ACME facilities adjacent to... price ” they were willing to “pay” in terms of potential modifications to current CoT practices and implementations. Future discussions should focus

  4. Comparing the creativity of children's design solutions based on expert assessment

    Thang, B.; Sluis - Thiescheffer, R.J.W.; Bekker, M.M.; Eggen, J.H.; Vermeeren, A.P.O.S.; Ridder, de H.

    2008-01-01

    LOBBI Netherlands Consortium Subscribe (Full Service) Register (Limited Service, Free) Login Search: The ACM Digital Library The Guide Feedback Comparing the creativity of children's design solutions based on expert assessment Full text Pdf (3.04 MB) Source Interaction Design and Children archive

  5. Predicting Character Traits Through Reddit

    2015-01-01

    and even employers (Res). Companies like Netflix also use personality classification algorithms in order to provide users with predictions of movies...science behind the netflix algorithms that decide what to watch next, August 2013. Reza Zafarani and Huan Liu. Evaluation without ground truth in social media research. Communications Of The ACM, 58(6):54–60, June 2015. 12

  6. Electrical and microstructural characterization of silver sheathed high Tc superconductors wires and ribbons

    Chaffron, L.; Regnier, P.; Schmirgeld, L.; Maurice, F.; Aguillon, C.; Senoussi, S.

    1991-01-01

    High Tc superconductors wires and ribbons were prepared according to the powder in tube method. It is shown that the electrical performances of the so prepared superconductors can be considerably improved, first by increasing as much as possible the density of the green body before sintering, and afterwards by melt texturing the sintered conductors. Some measurements of the transport critical current density of our conductors as a function of their diameter or their thickness are then presented and compared with indirect values obtained via the Bean method. The highest transport Jc measured in the present study, before melt texturing, are: 2250 and 5100 A/cm 2 at 77 and 63 K respectively, for a 50 μm thick silver sheathed ribbon. These figures compare nicely with the values of the intergranular critical current densities determined from magnetic measurements which are: 2100 and 5000 A/cm 2 at the same temperatures, and 40000 A/cm 2 at 4.2 K. Much higher intergranular values, in the range of 10 5 A/cm 2 were obtained after melt texturing the wires. Finally, microstructural characterizations carried out by X-ray diffraction, electron microprobe analysis and transmission electron microscopy are reported and discussed

  7. Measuring and Inferring the State of the User via the Microsoft Kinect with Application to Cyber Security Research

    2018-01-16

    professional recruiters evaluate videotapes of a job interview to make a hiring decision; the nonverbal cues best predicting the hiring decision were found to...Blake A, Cook M, Moore R. Real-time human pose recognition in parts from single depth images. Communications of the ACM. 2013;56(1):116–124. Shum HP

  8. Promoting Daily Physical Activity by Means of Mobile Gaming: A Review of the State of the Art

    Tabak, Monique; van Weering, Marit; van Dijk, H.W.; Vollenbroek-Hutten, Miriam Marie Rosé

    2015-01-01

    Objectives: To review mobile games and gaming applications that claim to improve physical activity behavior in daily life. Search Methods: We searched PubMed, Web of Science, and the ACM Digital Library and performed a manual search of relevant journals and reference lists. Studies that reported on

  9. On hardness of multilinearization, and VNP-completeness in characteristics 2

    Hrubeš, Pavel

    2016-01-01

    Roč. 9, č. 1 (2016), č. článku 1. ISSN 1942-3454 EU Projects: European Commission(XE) 339691 - FEALORA Institutional support: RVO:67985840 Keywords : boolean formula * complexity measure Subject RIV: BA - General Mathematics http://dl.acm.org/ citation .cfm?doid=3007903.2940323

  10. Parity games and propositional proofs

    Beckmann, A.; Pudlák, Pavel; Thapen, Neil

    2014-01-01

    Roč. 15, č. 2 (2014), s. 17 ISSN 1529-3785 R&D Projects: GA AV ČR IAA100190902 Institutional support: RVO:67985840 Keywords : bounded arithmetic * mean payoff games * parity games Subject RIV: BA - General Mathematics Impact factor: 0.618, year: 2014 http://dl.acm.org/ citation .cfm?doid=2616911.2579822

  11. The hardness of being private

    Ada, A.; Chattopadhyay, S.; Cook, S.A.; Fontes, L.; Koucký, Michal; Pitassi, T.

    2014-01-01

    Roč. 6, č. 1 (2014), s. 1 ISSN 1942-3454 R&D Projects: GA ČR GAP202/10/0854; GA AV ČR IAA100190902 Institutional support: RVO:67985840 Keywords : approximate privacy * communication complexity * information theory Subject RIV: BA - General Mathematics http://dl.acm.org/ citation .cfm?doid=2600088.2567671

  12. Complexity of Propositional Proofs Under a Promise

    Dershowitz, N.; Tzameret, Iddo

    2010-01-01

    Roč. 11, č. 3 (2010), s. 1-29 ISSN 1529-3785 Institutional research plan: CEZ:AV0Z10190503 Keywords : theory * promise problems * propositional proof complexity * random 3CNF * resolution Subject RIV: BA - General Mathematics Impact factor: 1.391, year: 2010 http://dl.acm.org/ citation .cfm?doid=1740582.1740586

  13. Complexity of Propositional Proofs Under a Promise

    Dershowitz, N.; Tzameret, Iddo

    2010-01-01

    Roč. 11, č. 3 (2010), s. 1-29 ISSN 1529-3785 Institutional research plan: CEZ:AV0Z10190503 Keywords : theory * promise problems * propositional proof complexity * random 3CNF * resolution Subject RIV: BA - General Mathematics Impact factor: 1.391, year: 2010 http://dl.acm.org/citation.cfm?doid=1740582.1740586

  14. Mutations in the Histone-Like Nucleoid Structuring Regulatory Gene (hns) Decrease the Adherence of Shiga Toxin-Producing Escherichia coli 091:H21 Strain B2F1 to Human Colonic Epithelial Cells and Increase the Production of Hemolysin

    Scott, Maria

    1999-01-01

    ...:H21 to human colonic epithelial cells. Transposon mutagenesis of B2F1 was accomplished with the mini-Tn5phoACm mobile element and a mutant bank of B2F1 colonies that carried putative in-frame PhoA-positive transposon insertions was isolated...

  15. Increasing Update Rates in the Building Walkthrough System with Automatic Model-Space Subdivision and Potentially Visible Set Calculations

    1990-07-01

    34 ACM Computing Surveys. 6(1): 1- 55. [Syzmanski85] Syzmanski, T. G. and C. J. V. Wyk. (1985). " GOALIE : A Space Efficient System for VLSI Artwork...this. Essentially we initialize a stack with the root. We then pull an element of this stack and if it is a cell we run the occlusion operation on the

  16. ANAESTHETIC MANAGEMENT IN A PATIENT WITH ARNOLD-CHI ARI MALFORMATION TYPE I AND SYRINGOMYELIA

    Kartika; Pratap; Vijayalaxmi; Kalyan Chakravarthy; Nagaraju

    2013-01-01

    ABSTRACT: Syringomyelia is an unusual neurological condition characterised by the the presence of cystic cavity in the spinal cord resultin g in neurological manifestations. Here, we report a safe anesthetic management of patient with Arnold-Ch iari malformation type I and syringomyelia posted for foramen magnum decompression . INTRODUCTION: Arnold-Chiari malformation (ACM) is a developmental malformation characterised by downward displacement of cere...

  17. Fabricating Synthetic Data in Support of Training for Domestic Terrorist Activity Data Mining Research

    2010-09-01

    of Mannheim seeks to produce realistic digital images for student analysis ( Moch & Freiling, 2009). Using instructor generated scripts and the...laboratory. ACM Transactions on Information and System Security, (pp. 262-294). Moch , C., & Freiling, F. (2009). The forensic image generator

  18. Experiments on the interaction between long Josephson junctions and a coplanar strip resonator

    Davidson, A.; Pedersen, Niels Falsig

    1992-01-01

    Experiments are reported on a new geometry designed to couple long Josephson junction fluxon oscillators to a resonant cavity. The junctions were made with a niobium-aluminum oxide-niobium trilayer process with a critical-current density of around 1000 A/cm2. Various numbers of such junctions wer...

  19. Open and regionalised spectrum repositories for emerging countries

    Arcia-Moret, A

    2016-08-01

    Full Text Available stream_source_info Arcia_Moret_18478_2016.pdf.txt stream_content_type text/plain stream_size 1324 Content-Encoding UTF-8 stream_name Arcia_Moret_18478_2016.pdf.txt Content-Type text/plain; charset=UTF-8 ACM SIGCOMM...

  20. Vijayapandi et al., Afr J Tradit Complement Altern Med. (2013) 10(1 ...

    AJTCAM

    with ACAE and ACME at 0.25, 0.5, 0.75 and 1 mg/ml, but at higher dose of ACAE, ... antioxidant and anticholinesterase activity of Acorus calamus reported ..... Central nervous system studies on an ethanol extract of Acorus calamus rhizomes.

  1. Particulate Characterization and Control Evaluation for Carbon Fiber Composite Aircraft Crash Recovery Operations

    2010-03-01

    Advanced Composite Office, Wright-Patterson BEE Flight, and USAFSAM for their help procuring the materials and supplies needed to perform this study...that would occur during an aircraft crash. The JP-8 was then 26 ignited with a butane lighter and allowed to burn to extinction . A burning ACM

  2. Evaluation of the Presentation of Network Data via Visualization Tools for Network Analysts

    2014-03-01

    distortion presentation techniques based on a tabular layout (10) such as Document Lens (11), fish -eye views (12, 13), stretching rubber sheets (14...User Interface Software and Technology, pages 29–38, ACM Press, 1998. 36. Schmitz, C. Limesurvey-the Open Source Survey Application. Hamburg [cited

  3. CSRI Summer Proceedings 2010

    2010-12-17

    interpreting the data. In particular, we thank Sophia Corwell, Matthew Bohnsack, Ken Lord, and Marcus Epperson. We thank David Day for his helpful...Commun. ACM, 33 (1990), pp. 30–53. [8] A. Guillon and D. Loach , YetiSim: a C++ simulation library with execution graphs instead of coroutines, in

  4. Efficient Security Mechanisms for the Border Gateway Routing Protocol

    1997-08-22

    Finding Algorithm for Loop- Free Routing. IEEE/ACM Transactions on Networking, 5(1):148{160, Feb. 1997. [7] International Standards Organization. ISO/IEC...Jersey 07974, Feb. 1985. ftp://netlib.att.com/netlib/att/cs/ cstr /117.ps.Z. [16] S. L. Murphy. Presentation in Panel on \\Security Architecture for the

  5. In Vitro Anticholinergic and Antihistaminic Activities of Acorus ...

    The present investigation was aimed at determining the effects of hexane, acetone, methanol and aqueous extracts of Acorus calamus leaves (ACHE, ACAE, ACME and ACAQE) on cholinergic and histaminic system using isolated frog rectus abdominis muscle and guinea pig ileum. A dose dependent potentiation of Ach ...

  6. Preface

    Brand, van den M.G.J.; Gasevic, D.; Gray, J.; Brand, van den M.G.J.; Gasevic, D.; Gray, J.

    2010-01-01

    We are pleased to present the proceedings of the Second International Conference on Software Language Engineering (SLE 2009). The conference was held in Denver, Colorado (USA) during October 5–6, 2009 and was co-located with the 12th IEEE/ACM International Conference on Model-Driven Engineering

  7. Influence of Precursor Composition on the Microstructure and Superconducting Properties of Dy-Ba-Cu-O filaments

    Ikebe, Y; Ban, E; Matsuoka, Y; Nishijima, G; Watanabe, K

    2006-01-01

    Dy-Ba-Cu-O filaments have been successfully fabricated by a solution spinning method. The relationship between the partial melting temperature and the transport J c value at 77 K of the filamentary sample was systematically investigated. Two kinds of precursor filaments with starting composition of Dy:Ba:Cu = 1.18:2.12:3.09 (sample A)and Dy:Ba:Cu = 1.00:2.00:3.00 (sample B) were partially melted in 1%O 2 + Ar atmospheric gas and oxygenated in pure 100% O 2 gas. Samples partially melted at a wide temperature range of 990-1040 deg. C had J c values higher than 10 4 A/cm 2 . Both sample A and sample B partially melted at 1020 deg. C exhibited the maximum J c value higher than 4.2 x 10 4 A/cm 2 and 2.0 x 10 4 A/cm 2 , respectively. These samples had a dense microstructure consisting predominantly of Dy123 and finely dispersed Dy211 particles. The Dy211 particles with a diameter of about 1μm were finely dispersed in sample A, while the particles with a diameter of about 5μm were observed in sample B. The J c values of both samples were maintained about 2.0 x 10 3 A/cm 2 up to 14 T

  8. International workshop on multimodal virtual and augmented reality (workshop summary)

    Hürst, W.O.; Iwai, Daisuke; Balakrishnan, Prabhakaran

    2016-01-01

    Virtual reality (VR) and augmented reality (AR) are expected by many to become the next wave of computing with significant impacts on our daily lives. Motivated by this, we organized a workshop on “Multimodal Virtual and Augmented Reality (MVAR)” at the 18th ACM International Conference on

  9. Paradigms and laboratories in the core computer science curriculum: An overview

    Hartel, Pieter H.; Hertzberger, L.O.

    1995-01-01

    Recent issues of the bulletin of the ACM SIGCSE have been scrutinised to find evidence that the use of laboratory sessions and different programming paradigms improve learning difficult concepts and techniques, such as recursion and problemsolving. Many authors in the surveyed literature be- lieve

  10. 77 FR 65887 - Ocean Transportation Intermediary License Applicants

    2012-10-31

    ..., Washington, DC 20573, by telephone at (202) 523-5843 or by email at [email protected] . ACM Logistics & Consulting... Type: New OFF License; Highland Project Logistics, Inc. (NVO & OFF), 35 Constitution Drive, Suite A.... Bonner, Special Manager (QI), Martine L. Plunkett, Manager, Application Type: Additional QI; Radiant...

  11. Hidden in Plain Sight: Signs of Great Power War

    2016-06-01

    China can change the strategic balance of power in the region without ever fighting—the acme of skill according to Sun Tzu . In fact, the balance of...68 BIBLIOGRAPHY ...put anyone into the shade, but we demand a place for ourselves in the sun .”20 This speech became the ideological foundation for Germany’s

  12. Distributed Kernelized Locality-Sensitive Hashing for Faster Image Based Navigation

    2015-03-26

    using MapReduce was described by Moise et al. in their paper, “Indexing and searching 100 million images with map-reduce” [9]. They modified the...D. Moise , D. Shestakov, G. Gudmundsson, and L. Amsaleg, “Indexing and Searching 100M Images with Map-Reduce,” in Proceedings of the 3rd ACM con

  13. Fixing the Problem With Empathy: Development and Validation of the Affective and Cognitive Measure of Empathy.

    Vachon, David D; Lynam, Donald R

    2016-04-01

    Low empathy is a criterion for most externalizing disorders, and empathy training is a regular component of treatment for aggressive people, from school bullies to sex offenders. However, recent meta-analytic evidence suggests that current measures of empathy explain only 1% of the variance in aggressive behavior. A new assessment of empathy was developed to more fully represent the empathy construct and better predict important outcomes--particularly aggressive behavior and externalizing psychopathology. Across three independent samples (N = 210-708), the 36-item Affective and Cognitive measure of Empathy (ACME) was internally consistent, structurally reliable, and invariant across sex. The ACME bore significant associations to important outcomes, which were incremental relative to other measures of empathy and generalizable across sex. Importantly, the affective scales of the ACME-particularly a new "Affective Dissonance" scale--yielded moderate to strong associations with aggressive behavior and externalizing disorders. The ACME is a short, reliable, and useful measure of empathy. © The Author(s) 2015.

  14. 抑制扩频系统中窄带干扰的新卡尔曼滤波算法%New Kalman Filtering Algorithm for Narrowband Interference Suppression in Spread Spectrum Systems

    许光辉; 胡光锐

    2005-01-01

    A new Kalman filtering algorithm based on estimation of spread spectrum signal before suppression of narrowband interference (NBI) in spread spectrum systems, using the dependence of autoregressive (AR) interference, is presented compared with performance of the ACM nonlinear filtering algorithm, simulation results show that the proposed algorithm has preferable performance, there is about 5 dB SNR improvement in average.

  15. Dynamic Protocol Reverse Engineering: A Grammatical Inference Approach

    2008-03-01

    domain-specific languages”. OOPSLA ’05: Companion to the 20th annual ACM SIGPLAN conference on Object-oriented programming, systems, languages, and...Representation to k-TSS Lan- guage Models”. Computación y Sistemas , 3(4):273–244, 2000. ISSN 1405-5546. 256. Trakhtenbrot, B.A. and Y.M. Barzdin. Finite

  16. Benchmarking European Gas Transmission System Operators

    Agrell, Per J.; Bogetoft, Peter; Trinkner, Urs

    This is the final report for the pan-European efficiency benchmarking of gas transmission system operations commissioned by the Netherlands Authority for Consumers and Markets (ACM), Den Haag, on behalf of the Council of European Energy Regulators (CEER) under the supervision of the authors....

  17. Determination of University Students' Most Preferred Mobile Application for Gamification

    Bicen, Huseyin; Kocakoyun, Senay

    2017-01-01

    In this digital age of technological advancement, mobile applications are fastly approaching acme of development. In order to increase the efficiency of the developed applications, mobile applications which are suitable for gamification have become a contemporary issue. In this study, the applications of Kahoot, ClassDojo, Classcraft and Socrative…

  18. Critical currents and weak links in melt textured R123

    Veal, B. W.; Zhang, H.; Claus, H.; Chen, L.; Paulikas, A. P.; Koshelev, A.; Crabtree, G. W.

    2000-01-01

    Weak link behavior is studied, using magnetization and Hall probe measurements of ring samples, in welded melt-textured R123 monoliths and in dual-seeded samples with disoriented domains. Techniques for welding samples yield transport currents across the junction that are in excess of 10 4 A/cm 2

  19. Development of Field-Emission Electron Gun from Carbon Nanotubes

    Hozumi, Y

    2004-01-01

    Aiming to use a narrow energy-spread electron beam easily and low costly on injector electron guns, we have been tested field emission cathodes of carbon nanotubes (CNTs). Experiments for these three years brought us important suggestions and a few rules of thumb. Now at last, anode current of 3.0 [A/cm2

  20. Parity games and propositional proofs

    Beckmann, A.; Pudlák, Pavel; Thapen, Neil

    2014-01-01

    Roč. 15, č. 2 (2014), s. 17 ISSN 1529-3785 R&D Projects: GA AV ČR IAA100190902 Institutional support: RVO:67985840 Keywords : bounded arithmetic * mean payoff games * parity games Subject RIV: BA - General Mathematics Impact factor: 0.618, year: 2014 http://dl.acm.org/citation.cfm?doid=2616911.2579822

  1. Reliable Internet Routing

    2011-09-01

    global coordination. IEEE/ACM Trans. Netw., 9(6):681–692, 2001. [39] S. Goldberg, D. Xiao, E. Tromer, B. Barak , and J. Rexford. Path-quality monitoring...RFC 4271). [81] Y. Rekhter, T. Li, and S. Hares. A border gateway protocol 4 (BGP-4), 2006. IETF RFC 4271. [82] E. Rosen , A. Viswanathan, and R. Callon

  2. H- source developments

    Allison, P.W.

    1978-01-01

    The design and operation of a Penning discharge, cold cathode, surface plasma H - ion source are described. A high current density, about 2 A/cm 2 , is extracted from the source by putting about 20 keV across the 2 to 2 1 / 2 mm gap

  3. 29 CFR 1926.1101 - Asbestos.

    2010-07-01

    ..., grinding or other method that breaks, crumbles, or disintegrates intact ACM. Amended water means water to... by this standard, even though the general contractor is not qualified to serve as the asbestos... months of the current or projected job, the monitoring and analysis were performed in compliance with the...

  4. Using an active contour method to detect bilge dumps from SAR imagery

    Mdakane, Lizwe W

    2016-07-01

    Full Text Available An automatic approach to detect bilge dumping in synthetic aperture radar (SAR) images over Southern African oceans is proposed. The approach uses a threshold-based algorithm and a region-based active contour model (ACM) algorithm to achieve...

  5. Astrocytes expressing ALS‐linked mutant FUS induce motor neuron death through release of tumor necrosis factor‐alpha

    Kia, Azadeh; McAvoy, Kevin; Krishnamurthy, Karthik; Trotti, Davide

    2018-01-01

    Mutations in fused in sarcoma (FUS) are linked to amyotrophic lateral sclerosis (ALS), a fatal neurodegenerative disease affecting both upper and lower motor neurons. While it is established that astrocytes contribute to the death of motor neurons in ALS, the specific contribution of mutant FUS (mutFUS) through astrocytes has not yet been studied. Here, we used primary astrocytes expressing a N‐terminally GFP tagged R521G mutant or wild‐type FUS (WTFUS) and show that mutFUS‐expressing astrocytes undergo astrogliosis, damage co‐cultured motor neurons via activation of an inflammatory response and produce conditioned medium (ACM) that is toxic to motor neurons in isolation. Time lapse imaging shows that motor neuron cultures exposed to mutFUS ACM, but not WTFUS ACM, undergo significant cell loss, which is preceded by progressive degeneration of neurites. We found that Tumor Necrosis Factor‐Alpha (TNFα) is secreted into ACM of mutFUS‐expressing astrocytes. Accordingly, mutFUS astrocyte‐mediated motor neuron toxicity is blocked by targeting soluble TNFα with neutralizing antibodies. We also found that mutant astrocytes trigger changes to motor neuron AMPA receptors (AMPAR) that render them susceptible to excitotoxicity and AMPAR‐mediated cell death. Our data provide the first evidence of astrocytic involvement in FUS‐ALS, identify TNFα as a mediator of this toxicity, and provide several potential therapeutic targets to protect motor neurons in FUS‐linked ALS. PMID:29380416

  6. Reducing the occurrence of plant events through improved human performance

    Ross, T.; Burkhart, A.D.

    1993-01-01

    During a routine control room surveillance, the reactor operator is distracted by an alarming secondary annunciator and a telephone call. When the reactor operator resumes the surveillance, he inadvertently performs the procedural steps out of order. This causes a reportable nuclear event. How can procedure-related human performance problems such as this be prevented? The question is vitally important for the nuclear industry. The U.S. Nuclear Regulatory Commission's Office for Analysis and Evaluation of Operational Data observed, open-quotes With the perceived reduction in the number of events caused by equipment failures, INPO and other industry groups and human performance experts agree that a key to continued improvement in plant performance and safety is improved human performance.close quotes In fact, open-quotes more than 50% of the reportable events occurring at nuclear power plants involve human error.close quotes Prevention (or correction) of a human performance problem is normally based on properly balancing the following three factors: (1) supervisory involvement; (2) personnel training; and (3) procedures. The nuclear industry is implementing a formula known as ACME, which better balances supervisory involvement, personnel training, and procedures. Webster's New World Dictionary defines acme as the highest point, the peak. ACME human performance is the goal: ACME Adherence to and use of procedures; Self-Checking; Management Involvement; and Event Investigations

  7. Cluster structure of light nuclei

    Iachello, Francesco

    2018-02-01

    Matter and charge densities of kα structures with k=2 (8Be), k=3 (12C) and k=4 (16O) calculated within the framework of the algebraic cluster model (ACM) are briefly reviewed and explicitly displayed. Their parameters are determined from a comparison with electron scattering data.

  8. Anesthetic management in a child with Arnold-Chiari malformation and bilateral vocal cord paralysis.

    Setz, A.C.W.; Boer, H.D. de; Driessen, J.J.; Scheffer, G.J.

    2005-01-01

    We report a case of a child who was scheduled for an emergency ventriculoperitoneal shunt procedure. The patient had a type II Arnold-Chiari malformation (ACM) and associated hydrocephalus and presented with near complete respiratory obstruction from bilateral abductor vocal cord palsy. Early

  9. Prognostic value of exercise capacity among patients with treated depression: The Henry Ford Exercise Testing (FIT) Project.

    Ahmed, Amjad M; Qureshi, Waqas T; Sakr, Sherif; Blaha, Michael J; Brawner, Clinton A; Ehrman, Jonathan K; Keteyian, Steven J; Al-Mallah, Mouaz H

    2018-04-01

    Exercise capacity is associated with survival in the general population. Whether this applies to patients with treated depression is not clear. High exercise capacity remains associated with lower risk of all-cause mortality (ACM) and nonfatal myocardial infraction (MI) among patients with treated depression. We included 5128 patients on antidepressant medications who completed a clinically indicated exercise stress test between 1991 and 2009. Patients were followed for a median duration of 9.4 years for ACM and 4.5 years for MI. Exercise capacity was estimated in metabolic equivalents of tasks (METs). Cox proportional hazards regression models were used. Patients with treated depression who achieved ≥12 METs (vs those achieving model, exercise capacity was associated with a lower ACM (HR per 1-MET increase in exercise capacity: 0.82, 95% CI: 0.79-0.85, P capacity had an inverse association with both ACM and nonfatal MI in patients with treated depression, independent of cardiovascular risk factors. These results highlight the potential impact of assessing exercise capacity to identify risk, as well as promoting an active lifestyle among treated depression patients. © 2018 Wiley Periodicals, Inc.

  10. Coupling Considerations in Assembly Language

    2018-01-05

    done in assembly languages—just write a command that modifies the opcode of another command. A module modifying (or referring to) local data in...178C.) 3. Martin Fowler. Last accessed 6 November 2017, http://martinfowler.com. Email is fowler@acm.org. 4. “Thoughts on Coupling in Software

  11. Coupling Considerations in Assembly Language. Revision 1

    2018-02-13

    practice of dynamically changing code. This can easily be done in assembly languages—just write a command that modifies the opcode of another command...November 2017, http://martinfowler.com. Email is fowler@acm.org. 4. “Thoughts on Coupling in Software Design,” by Ioan Fagarasan, posted 25 July 2016

  12. Peer production & peer support at the Free Technology Academy

    Potters, Hanneke; Berlanga, Adriana; Bijlsma, Lex

    2012-01-01

    Potters, H., Berlanga, A. J., & Lex, B. (2011). Peer Production & Peer Support at the Free Technology Academy. In G. van de Veer, P. B. Sloep, & M. van Eekelen (Eds.), Proceedings Computer Science Education Research Conference (CSERC '11) (pp. 49-58). April, 7-8, 2011, Heerlen, The Netherlands: ACM.

  13. Bio-magnetochronology for the upper Campanian-Maastrichtian from the Gubbio area, Italy

    Gardin, Silvia; Galbrun, Bruno; Thibault, Nicolas Rudolph

    2012-01-01

    A new bio-chronostratigraphic framework is presented for the upper Campanian - Maastrichtian pelagic sediments of the Gubbio area (Bottaccione and Contessa Highway sections, Italy). New planktonic foraminiferal (FO of P. hantkeninoides), calcareous nannofossil (FO of M. prinsii, base acme of M. m...

  14. Modification of solid surface by intense pulsed light-ion and metal-ion beams

    Nakagawa, Y.; Ariyoshi, T.; Hanjo, H.; Tsutsumi, S.; Fujii, Y.; Itami, M.; Okamoto, A.; Ogawa, S.; Hamada, T.; Fukumaru, F.

    1989-03-01

    Metal surfaces of Al, stainless-steel and Ti were bombarded with focused intense pulsed proton and carbon ion beams (energy ˜ 80 keV, current density ≲ 1000 A/cm 2, pulse width ˜ 300 ns). Thin titanium carbide layers were produced by carbon-ion irradiation on the titanium surface. The observed molten surface structures and recrystallized layer (20 μm depth) indicated that the surfaces reached high temperatures as a result of the irradiation. The implantation of intense pulsed metal ion beams (Al +, ˜ 20 A/cm 2) with simultaneous deposition of anode metal vapor on Ti and Fe made a mixed layer of AlTi and AlFe of about 0.5 μm depth. Ti and B multilayered films evaporated on glass substrates were irradiated by intense pulsed proton beams of relatively lower current density (10-200 A/cm 2). Ti films containing B atoms above 10 at.% were obtained. When the current density was about 200 A/cm 2 diffraction peaks of TiB 2 appeared.

  15. Digital health innovation ecosystems: From systematic literature review to conceptual framework

    Iyawa, GE

    2016-10-01

    Full Text Available innovation ecosystem as part of a larger study. A systematic literature review was conducted on four academic databases: ACM, ScienceDirect, IEEE Xplore and SpringerLink. Due to the dearth in initial search results, the search was broadened to include non...

  16. BioSTEC 2017: 10th International Joint Conference on Biomedical Engineering Systems and Technologies : Proceedings Volume 5: HealthInf

    2017-01-01

    This book contains the proceedings of the 10th International Joint Conference on Biomedical Engineering Systems and Technologies (BIOSTEC 2017). This conference is sponsored by the Institute for Systems and Technologies of Information, Control and Communication (INSTICC), in cooperation with the ACM

  17. How to Implement Rigorous Computer Science Education in K-12 Schools? Some Answers and Many Questions

    Hubwieser, Peter; Armoni, Michal; Giannakos, Michail N.

    2015-01-01

    Aiming to collect various concepts, approaches, and strategies for improving computer science education in K-12 schools, we edited this second special issue of the "ACM TOCE" journal. Our intention was to collect a set of case studies from different countries that would describe all relevant aspects of specific implementations of…

  18. Improved methods for binding acma-type protein anchor fusions yo cell-wall material of micro-organisms

    Leenhouts, Cornelis; Ramasamy, R.; Steen, Anton; Kok, Jan; Buist, Girbe; Kuipers, Oscar

    2002-01-01

    The invention provides a method for improving binding of a proteinaceous substance to cell-wall material of a Gram-positive bacterium, said substance comprising an AcmA cell wall binding domain or homolog or functional derivative thereof, said method comprising treating said cell-wall material with

  19. Camera Geo calibration Using an MCMC Approach (Author’s Manuscript)

    2016-08-19

    definition , a lower total distance to find the ground-truth candidate is better. The definition of the total area, Ta, is similar: we center a l × l...Photo tourism : exploring photo collections in 3d,” ACM Transactions on Graphics, vol. 25, no. 3, pp. 835–846, 2006. 2 [17] Yunpeng Li, Noah Snavely, Dan

  20. Microstructure and tribological behavior of tungsten-containing diamondlike carbon coated rubbers

    Pei, Y.T.; Bui, X.L.; Zhou, Xiao; Hosson, J.Th.M. De

    2008-01-01

    Tungsten-containing diamondlike carbon (W-DLC) coatings have been deposited on FKM (fluorocarbon), ACM (acrylate), and HNBR (hydrogenated nitrile butadiene) rubbers via unbalanced magnetron reactive sputtering from a WC target in C2H2/Ar plasma. The surface morphology and, fracture cross sections of

  1. Computing the scattering properties of participating media using Lorenz-Mie theory

    2007-01-01

    This source code implements Lorenz-Mie theory using the formulas presented in the SIGGRAPH 2007 paper: J. R. Frisvad, N. J. Christensen, and H. W. Jensen: "Computing the Scattering Properties of Participating Media Using Lorenz-Mie Theory". Copyright (c) ACM 2007. This is the author's version...

  2. Joint Services Electronics Program.

    1985-03-30

    Siences and Systems, Baltimore, MD, March 27-29, 1985, to appear (JSEP/NSF/Kodak). 2. G. Bilardi and F. P. Preparata, "Tessellation techniques for...ADDITONAIL INFORMATION: Awards and Honors: Donna J. Broan Outstanding Young Woman of America, 1984 Member-at-Large, ACM, SIGACT1, 1983-85 * Michael C

  3. The use of multiplicative models for analysis of road safety data.

    Oppe, S.

    1978-01-01

    Accident ratios are analysed with regard to the variables road surface skidding resistance and hourly traffic volume. In a first analysis the additive conjoint measurement model (acm) is used to investigate to what extent the accident ratios can be described as a result of independent contributions

  4. Research foci of computing research in South Africa as reflected by publications in the South African computer journal

    Kotzé, P

    2009-01-01

    Full Text Available of research articles published in SACJ over its first 40 volumes of the journal using the ACM Computing Classification Scheme as basis. In their analysis the authors divided the publications into three cycles of more or less six years in order to identify...

  5. Room-temperature synthesis of TiO 2 nanospheres and their solar driven photoelectrochemical hydrogen production

    Avasare, Vidya; Zhang, Zhongai; Avasare, Dnyaneshwar; Khan, Ibrahim; Qurashi, Ahsanulhaq

    2015-01-01

    O2 nanospheres was studied under illumination of AM 1.5G. The optimized photocurrent density and photoconversion efficiency of TiO2 NSPs were observed ~0.95mAcm-2 at 1.23V and 0.69%, respectively. The transient photocurrent response measurements

  6. Artifical Intelligence for Human Computing

    Huang, Th.S.; Nijholt, Antinus; Pantic, Maja; Pentland, A.; Unknown, [Unknown

    2007-01-01

    This book constitutes the thoroughly refereed post-proceedings of two events discussing AI for Human Computing: one Special Session during the Eighth International ACM Conference on Multimodal Interfaces (ICMI 2006), held in Banff, Canada, in November 2006, and a Workshop organized in conjunction

  7. Magnetic penetration depth δ o and critical current density in Y-BA-Cu-O crystals

    Zavaritsky, N.V.; Zavaritsky, V.N.

    1989-01-01

    Magnetic penetration depthδ o ∼1.03 10 - 5 cm and critical current density (j c = 0.5 divided-by 1 x 10 5 A/cm 2 at T/T ∼0.98) are determined from low-field do magnetization measurements on Y 1 Ba 2 Cu 3 O 7 - crystals

  8. Interactive effects of trait and state affect on top-down control of attention.

    Hur, Juyoen; Miller, Gregory A; McDavitt, Jenika R B; Spielberg, Jeffrey M; Crocker, Laura D; Infantolino, Zachary P; Towers, David N; Warren, Stacie L; Heller, Wendy

    2015-08-01

    Few studies have investigated how attentional control is affected by transient affective states while taking individual differences in affective traits into consideration. In this study, participants completed a color-word Stroop task immediately after undergoing a positive, neutral or negative affective context manipulation (ACM). Behavioral performance was unaffected by any ACM considered in isolation. For individuals high in trait negative affect (NA), performance was impaired by the negative but not the positive or neutral ACM. Neuroimaging results indicate that activity in primarily top-down control regions of the brain (inferior frontal gyrus and dorsal anterior cingulate cortex) was suppressed in the presence of emotional arousal (both negative and positive ACMs). This effect appears to have been exacerbated or offset by co-occurring activity in other top-down control regions (parietal) and emotion processing regions (orbitofrontal cortex, amygdala and nucleus accumbens) as a function of the valence of state affect (positive or negative) and trait affect (trait NA or trait PA). Neuroimaging results are consistent with behavioral findings. In combination, they indicate both additive and interactive influences of trait and state affect on top-down control of attention. © The Author (2015). Published by Oxford University Press. For Permissions, please email: journals.permissions@oup.com.

  9. The Cronus Distributed DBMS (Database Management System) Project

    1989-10-01

    projects, e.g., HiPAC [Dayal 88] and Postgres [Stonebraker 86]. Although we expect to use these techniques, they have been developed for centralized...Computing Systems, June 1989. (To appear). [Stonebraker 86] Stonebraker, M. and Rowe, L. A., "The Design of POSTGRES ," Proceedings ACM SIGMOD Annual

  10. Content Based Retrieval Database Management System with Support for Similarity Searching and Query Refinement

    2002-01-01

    to the OODBMS approach. The ORDBMS approach produced such research prototypes as Postgres [155], and Starburst [67] and commercial products such as...Kemnitz. The POSTGRES Next-Generation Database Management System. Communications of the ACM, 34(10):78–92, 1991. [156] Michael Stonebreaker and Dorothy

  11. A Mediator Architecture for Abstract Data Access

    1990-02-23

    Almost- Hierarchical Descriptions, Artificial Intelligence 14, 1980, pp.1 -3 9 . [201 M.Stonebraker: The Design of POSTGRES , Proc. ACM SIGMOD Conf...Trans. on Office Information Systems, Vol.5, No.1, January 1987, pp. 48 - 69. [5] Stonebraker, M., Rowe, L., "The Design of POSTGRES ," Proceedings of

  12. Stronger Consistency and Semantics for Low-Latency Geo-Replicated Storage

    2013-06-01

    Wallach, Mike Burrows , Tushar Chandra, Andrew Fikes, and Robert E. Gruber. Bigtable: A distributed storage system for structured data. ACM TOCS, 26(2...propagation for weakly consistent replication. In SOSP, October 1997. [60] Larry Peterson, Andy Bavier, and Sapan Bhatia. VICCI: A programmable cloud

  13. High-Performance Single Nanowire Tunnel Diodes

    Wallentin, Jesper; Persson, Johan Mikael; Wagner, Jakob Birkedal

    2010-01-01

    We demonstrate single nanowire tunnel diodes with room temperature peak current densities of up to 329 A/cm(2). Despite the large surface to volume ratio of the type-II InP-GaAs axial heterostructure nanowires, we measure peak to valley current ratios (PVCR) of up to 8.2 at room temperature and 27...

  14. 78 FR 9785 - Airworthiness Directives; Lindstrand Hot Air Balloons Ltd Appliances

    2013-02-12

    ... Airworthiness Directives; Lindstrand Hot Air Balloons Ltd Appliances AGENCY: Federal Aviation Administration... airworthiness directive (AD) for certain Lindstrand Hot Air Balloons Ltd female ACME threaded hose connectors...., Washington, DC 20590. For service information identified in this AD, contact Lindstrand Hot Air Balloons Ltd...

  15. Awareness Support in Scientific Event Management with ginkgo

    Reinhardt, Wolfgang; Maicher, Julian; Drachsler, Hendrik; Sloep, Peter

    2011-01-01

    Reinhardt, W., Maicher, J., Drachsler, H., & Sloep, P. B. (2011). Awareness Support in Scientific Event Management with ginkgo. In Proceedings of the 11th International Conference on Knowledge Management and Knowledge Technologies (i-Know’11) (pp. 40:1–40:8). New York, NY, USA: ACM.

  16. Summary for AVEC 2017 - Real-life depression and affect challenge and workshop

    Ringeval, Fabien; Schuller, Björn; Valstar, Michel; Gratch, Jonathan; Cowie, Roddy; Pantic, Maja

    2017-01-01

    The seventh Audio-Visual Emotion Challenge and workshop AVEC 2017 was held in conjunction with ACM Multimedia'17. This year, the AVECseries addresses two distinct sub-challenges: emotion recognition and depression detection. The Affect Sub-Challenge is based on a novel dataset of human-human

  17. Multimedia with a speech track: searching spontaneous conversational speech

    Larson, Martha; Ordelman, Roeland J.F.; de Jong, Franciska M.G.; Kohler, Joachim; Kraaij, Wessel

    After two successful years at SIGIR in 2007 and 2008, the third workshop on Searching Spontaneous Conversational Speech (SSCS 2009) was held conjunction with the ACM Multimedia 2009. The goal of the SSCS series is to serve as a forum that brings together the disciplines that collaborate on spoken

  18. Supplier–customer relationships: Weaknesses in south african automotive supply chains

    M. J. Naude

    2012-11-01

    Full Text Available The South African automotive industry, which is an important sector in the South African economy, needs to function efficiently if it is to compete internationally. However, South African automotive components manufacturers (ACMs are not internationally competitive and automotive assemblers, also known as original equipment manufacturers (OEMs, often import cheaper components from abroad. All parties in the South African automotive supply chains need each other to ensure optimal efficiency and competitiveness. Furthermore, it is vital that good relationships exist between customers and suppliers in the automotive supply chains in South Africa. ACMs are central to automotive supply chains. A survey was conducted among ACMs to determine the nature of relationships that exist between buyers and suppliers in South Africa’s automotive supply chains. The results showed that collaborative relationships do indeed exist between members of the supply chain but that communication, understanding of the parties’ situations and cooperation can improve this relationship and so create total alliance between OEMs and ACMs.

  19. Design and reliability analysis of high-speed and continuous data recording system based on disk array

    Jiang, Changlong; Ma, Cheng; He, Ning; Zhang, Xugang; Wang, Chongyang; Jia, Huibo

    2002-12-01

    In many real-time fields the sustained high-speed data recording system is required. This paper proposes a high-speed and sustained data recording system based on the complex-RAID 3+0. The system consists of Array Controller Module (ACM), String Controller Module (SCM) and Main Controller Module (MCM). ACM implemented by an FPGA chip is used to split the high-speed incoming data stream into several lower-speed streams and generate one parity code stream synchronously. It also can inversely recover the original data stream while reading. SCMs record lower-speed streams from the ACM into the SCSI disk drivers. In the SCM, the dual-page buffer technology is adopted to implement speed-matching function and satisfy the need of sustainable recording. MCM monitors the whole system, controls ACM and SCMs to realize the data stripping, reconstruction, and recovery functions. The method of how to determine the system scale is presented. At the end, two new ways Floating Parity Group (FPG) and full 2D-Parity Group (full 2D-PG) are proposed to improve the system reliability and compared with the Traditional Parity Group (TPG). This recording system can be used conveniently in many areas of data recording, storing, playback and remote backup with its high-reliability.

  20. Anthropomorphic Interfaces on Automation Trust, Dependence, and Performance inYounger and Older Adults

    2015-10-26

    Nomadic radio: Speech and audio interaction for contextual messaging in nomadic environments. ACM Transactions on Computer-Human Interaction, 7(3...be assessed: perceptual speed ( digit -symbol substitution; Wechsler, 1997), working memory (automated operation span (Aospan); Unsworth, Heitz...cognitive abilities test. These tests include the digit symbol test, reverse digit span test, and the Shipley vocabulary test. These tests will gather

  1. Future Field Programmable Gate Array (FPGA) Design Methodologies and Tool Flows

    2008-07-01

    Cruickshank, J. E. Gaffney and R. D. Melbourne, Australia : ACM, 1992. Proceedings of the 14th International Conference on Software Engineering. pp. 327-337... Ridge Compiler Collection Stone Ridge Technology 48 A.3 FPGA Architecture Survey Company Niche 3P plus 1 Technology Coarse-grain configurable IP

  2. An Analysis of Application Generators.

    1983-03-01

    query language OUEL in the programming language C, THESEUS [20], which embeds relational operators in the language Euclid. Schmidt [21] reports some...34The Design and Implementation of INGRES," ACM-TODS, Vol. 1. No. 3, 1976,. 33 £ 20. Shopiro,J.E., " THESEUS -A Programming Language for Relational

  3. A Massively Parallel Tensor Contraction Framework for Coupled-Cluster Computations

    2014-08-02

    64 (2004), pp. 1017 – 1026. [22] HONG JIA-WEI AND H. T. KUNG , I/O complexity: The red-blue pebble game, in Proceedings of the thirteenth annual ACM...electronic structure, Journal of Chemical Physics, 86 (1987), p. 7041. [36] JEPPE OLSEN, BJÖRN O. ROOS, POUL JØRGENSEN, AND HANS JØRGEN AA. JENSEN

  4. Towards synergy between the open source and the research multimedia communities

    P.S. Cesar Garcia (Pablo Santiago); W.T. Ooi (Wei Tsang); B. Moskowitz; Z. Babin; D.C.A. Bulterman (Dick); R. Lienhart; R. Richter

    2011-01-01

    htmlabstractThis panel extends current efforts from the ACM Multimedia 2011 Organization Committee in taking an important step towards open source projects. The panelists include speakers who are among the leading figures from the open source community. The goal is to provide a shared space for

  5. Measuring and Modeling Behavioral Decision Dynamics in Collective Evacuation

    2014-02-10

    1303.4629. 15. Leskovec J, Backstrom L, Kleinberg J (2009) Meme -tracking and the dynamics of the news cycle. Proc 15th ACM SIGKDD : 497505. 16. Leskovec J...2011) Memes online: Extracted, subtracted, injected, and recollected. Proc 5th Int AAAI Conf on Weblogs and Social Media : 353–360. 21. Watts DJ (2002) A

  6. RMIT at the TREC 2015 LiveQA Track

    2015-11-20

    recipient of an Australian Research Council DECRA Research Fellowship (DE140100275). REFERENCES [1] Michael Collins. Head-driven statistical models for...18th Australasian Document Computing Symposium, pages 58–65. ACM, 2013. [4] Matthias Petri, Alistair Moffat, and J Shane Culpepper. Score-safe term

  7. Review: Learning how to match fresco fragments

    van den Broek, Egon

    2012-01-01

    This paper was presented at Eurographics 2011. Being among the conference’s best papers, it was revised and republished in this ACM journal. In general, the authors present their approach as new; however, while this is not the case, it is probably an advancement in the domain of cultural heritage.

  8. LTSA Conformance Testing to Architectural Design of LMS Using Ontology

    Sengupta, Souvik; Dasgupta, Ranjan

    2017-01-01

    This paper proposes a new methodology for checking conformance of the software architectural design of Learning Management System (LMS) to Learning Technology System Architecture (LTSA). In our approach, the architectural designing of LMS follows the formal modeling style of Acme. An ontology is built to represent the LTSA rules and the software…

  9. Evaluating Modern Defenses Against Control Flow Hijacking

    2015-09-01

    instructions go bad: Generalizing return-oriented programming to risc . In In Proceedings of the 15th ACM conference on Computer and communications se... Computer Science in partial fulfillment of the requirements for the degree of Master of Science in Computer Science and Engineering at the MASSACHUSETTS...Department of Electrical Engineering and Computer Science

  10. A Learning Research Informed Design and Evaluation of a Web-Enhanced Object Oriented Programming Seminar

    Georgantaki, Stavroula C.; Retalis, Symeon D.

    2007-01-01

    "Object-Oriented Programming" subject is included in the ACM Curriculum Guidelines for Undergraduate and Graduate Degree Programs in Computer Science as well as in Curriculum for K-12 Computer Science. In a few research studies learning problems and difficulties have been recorded, and therefore, specific pedagogical guidelines and…

  11. Approximability of Robust Network Design

    Olver, N.K.; Shepherd, F.B.

    2014-01-01

    We consider robust (undirected) network design (RND) problems where the set of feasible demands may be given by an arbitrary convex body. This model, introduced by Ben-Ameur and Kerivin [Ben-Ameur W, Kerivin H (2003) New economical virtual private networks. Comm. ACM 46(6):69-73], generalizes the

  12. modelling the behaviour of interface surfaces using the finite eleme

    user

    Norwell, M.A.. 36. Wingo, etal, Hardware assisted self-collision for rigid and deformable surfaces, Journal of. Tele-operators and Virtual Environments. Dec., 2004. Vol. 13, No 6 pp 681-691. 37. Brian Von Herzen, etal. Geometric Collisions for Time- dependent parametric surfaces. ACM SIGGRAPH Computer Graphics, Aug.,.

  13. Evaluation of prognostic and predictive factors in breast cancer in Cuba. Its role in personalized therapy

    Álvarez Goyanes, Rosa Irene

    2011-01-01

    The identification of prognostic and predictive factors in breast cancer has allowed applying personalized therapeutic programs without achieving, still, the individualization for all patients. The objective of the present study was to evaluate the frequency of estrogen receptors, progesterone and HER2 along with the expression of the EGFR1 and ganglioside NglicolilGM3. 1509 patients found the frequency of expression of the aforementioned receivers, which were correlated with the morphological and General variables. It was compared the AcM recognition ior egf/r3 with a game of diagnosis - shopping, and the AcM 14F7 vitro tissue fresh and included in paraffin and in vivo labelled with 99mTc. It was obtained the frequency in Cuba of these prognostic and prediction markers of response, noting her hormone dependence of tumor associated with less aggressive features. The AcM 14F7 showed a broad recognition that was not correlated with prognostic factors, but was able to detect live in primary breast tumors. The ior egf/r3 exhibited 100% specificity and positive predictive value, as well as a sensitivity and negative predictive value of 68 and 73% respectively. The recognition of the AcM 14F7 and ior egf/r3 opens a new possibility of therapeutic directed against these targets for breast cancer (author)

  14. Formal Methods: Practice and Experience

    Woodcock, Jim; Larsen, Peter Gorm; Bicarregui, Juan

    2009-01-01

    . Based on this, we discuss the issues surrounding the industrial adoption of formal methods. Finally, we look to the future and describe the development of a Verified Software Repository, part of the worldwide Verified Software Initiative. We introduce the initial projects being used to populate...... the repository, and describe the challenges they address. © 2009 ACM. (146 refs.)...

  15. Health-friendly high-quality white light using violet-green-red laser and InGaN nanowires-based true yellow nanowires light-emitting diodes

    Janjua, Bilal; Ng, Tien Khee; Zhao, Chao; Anjum, Dalaver H.; Prabaswara, Aditya; Consiglio, Giuseppe Bernardo; Shen, Chao; Ooi, Boon S.

    2017-01-01

    , in conjunction with a yellow NWs-LED realized using molecular beam epitaxy technique, on titanium-coated silicon substrates. Unlike the conventional quantum-well-based LED, the NWs-LED showed efficiency-droop free behavior up to 9.8 A/cm with peak output power

  16. Building a Flexible Nework Infrastructure for Moving Target Defense

    2017-10-13

    testbed. We have published a paper in the CAN Workshop held in conjunction with the ACM CoNext 2016 conference [3]. ML implementations on OpenNetVM...Artificial Intelligence applications in the network Workshop held in conjunction with IEEE ICNP 2017 [4]. [1] Azeem Aqil, Karim Khalil, Ahmed Atya

  17. Fish oil-derived long-chain n-3 polyunsaturated fatty acids reduce expression of M1-associated macrophage markers in an ex vivo adipose tissue culture model, in part through adiponectin

    Anna A. De Boer

    2015-10-01

    Full Text Available Adipose tissue (AT macrophages (ATM play a key role in obesity-associated pathologies, and their phenotype can be influenced by the local tissue microenvironment. Interestingly, long-chain n-3 polyunsaturated fatty acids (LC n-3 PUFA and the LC n-3 PUFA-upregulated adipokine, adiponectin (Ad, may mitigate excessive ATM inflammatory M1-polarization responses. However, to what extent LC n-3 PUFA and Ad work in concert to affect macrophage phenotype has not been examined. Thus, we used an established ex vivo AT organ culture model using visceral AT from mice fed a control (CON; 10% w/w safflower oil n-6 PUFA-rich diet or an isocaloric fish-oil (FO; 3% w/w menhaden oil + 7% w/w safflower oil-derived LC n-3 PUFA-rich diet to generate AT conditioned media (ACM. We then evaluated if CON or FO ACM affected macrophage polarization markers in a model designed to mimic acute (18 h ACM plus LPS for the last 6 h or chronic (macrophages treated with LPS-challenged CON or FO ACM for 24 h inflammation ± Ad-neutralizing antibody and the LPS-neutralizing agent, polymyxin B. In the acute inflammation model, macrophages treated with FO ACM had decreased lipid uptake and mRNA expression of M1 markers (Nos2, Nfκb, Il6, Il18, Ccl2 and Ccl5 compared with CON ACM (p≤0.05; however, these effects were largely attenuated when Ad was neutralized (p>0.05. Further, in the chronic inflammation model, macrophages treated with FO ACM had decreased mRNA expression of M1 markers (Nos2, Tnfα, Ccl2 and Il1β and IL-6 and CCL2 secretion (p≤0.05; however, some of these effects were lost when Ad was neutralized, and were further exacerbated when both Ad and LPS were neutralized. Taken together, this work shows that LC n-3 PUFA and Ad work in concert to suppress certain M1 macrophage responses. Thus, future strategies to modulate the ATM phenotype should consider the role of both LC n-3 PUFA and Ad in mitigating obese AT inflammation.

  18. Fish Oil-Derived Long-Chain n-3 Polyunsaturated Fatty Acids Reduce Expression of M1-Associated Macrophage Markers in an ex vivo Adipose Tissue Culture Model, in Part through Adiponectin.

    De Boer, Anna A; Monk, Jennifer M; Liddle, Danyelle M; Power, Krista A; Ma, David W L; Robinson, Lindsay E

    2015-01-01

    Adipose tissue (AT) macrophages (ATM) play a key role in obesity-associated pathologies, and their phenotype can be influenced by the local tissue microenvironment. Interestingly, long-chain n-3 polyunsaturated fatty acids (LC n-3 PUFA) and the LC n-3 PUFA-upregulated adipokine, adiponectin (Ad), may mitigate excessive ATM inflammatory M1-polarization responses. However, to what extent LC n-3 PUFA and Ad work in concert to affect macrophage phenotype has not been examined. Thus, we used an established ex vivo AT organ culture model using visceral AT from mice fed a control (CON; 10% w/w safflower oil) n-6 PUFA-rich diet or an isocaloric fish oil (FO; 3% w/w menhaden oil + 7% w/w safflower oil)-derived LC n-3 PUFA-rich diet to generate AT conditioned media (ACM). We then evaluated if CON or FO ACM affected macrophage polarization markers in a model designed to mimic acute [18 h ACM plus lipopolysaccharide (LPS) for the last 6 h] or chronic (macrophages treated with LPS-challenged CON or FO ACM for 24 h) inflammation ± Ad-neutralizing antibody and the LPS-neutralizing agent, polymyxin B. In the acute inflammation model, macrophages treated with FO ACM had decreased lipid uptake and mRNA expression of M1 markers (Nos2, Nfκb, Il6, Il18, Ccl2, and Ccl5) compared with CON ACM (p ≤ 0.05); however, these effects were largely attenuated when Ad was neutralized (p > 0.05). Furthermore, in the chronic inflammation model, macrophages treated with FO ACM had decreased mRNA expression of M1 markers (Nos2, Tnfα, Ccl2, and Il1β) and IL-6 and CCL2 secretion (p ≤ 0.05); however, some of these effects were lost when Ad was neutralized, and were further exacerbated when both Ad and LPS were neutralized. Taken together, this work shows that LC n-3 PUFA and Ad work in concert to suppress certain M1 macrophage responses. Thus, future strategies to modulate the ATM phenotype should consider the role of both LC n-3 PUFA and Ad in mitigating obese AT

  19. Absence of a primary role for TTN missense variants in arrhythmogenic cardiomyopathy: From a clinical and pathological perspective.

    Chen, Kai; Song, Jiangping; Wang, Zhen; Rao, Man; Chen, Liang; Hu, Shengshou

    2018-05-01

    Arrhythmogenic cardiomyopathy (ACM) is an inheritable heart disease characterized by fibro-fatty replacement of the myocardium. TTN missense variants were previously reported as a pathogenic factor for ACM. TTN missense variants are commonly identified in ACM, but have limited effect on the phenotype of ACM. We sequenced 15 ACM-related genes in 35 patients who had a heart transplantation and quantified myocardium, and fibrous and adipose tissue in blocks of the explanted heart. Clinical and pathological characteristics were compared between patients with TTN variants and others. Pedigree analysis was performed in 3 families with TTN variants. TTN variants were detected in 11 patients (all missense, 9 heterozygous and 2 oligogenic form). The TTN truncating variant was absent in the cohort. Patients with TTN variants had late onset age of the disease (31 ±13 years vs 17 ±3 years, P = 0.049) and age of heart transplantation (41 ±14 years vs 24 ±9 years, P = 0.027), larger left ventricle end-diastolic diameter (62 ±10 mm vs 45 ±10 mm, P = 0.019), smaller right ventricular outflow tract (34 ±14 mm vs 50 ±15 mm, P = 0.046), more myocardium (40.8% ±29.4% vs 13.8% ±11.0%, P = 0.017), and less adipose tissue (43.0% ±30.9% vs 66.9% ±18.5%, P = 0.036) in right ventricle than those with desmosomal variants. There was few difference between patients with TTN variants and those without variants. Pedigrees showed none of the family members with TTN missense variants had a disease phenotype, indicating a very low penetrance. TTN missense variants was commonly identified in ACM patients in this cohort, but hardly played a primary role in ACM as causative variants. © 2018 Wiley Periodicals, Inc.

  20. Quantitative analysis of aortic regurgitation: real-time 3-dimensional and 2-dimensional color Doppler echocardiographic method--a clinical and a chronic animal study

    Shiota, Takahiro; Jones, Michael; Tsujino, Hiroyuki; Qin, Jian Xin; Zetts, Arthur D.; Greenberg, Neil L.; Cardon, Lisa A.; Panza, Julio A.; Thomas, James D.

    2002-01-01

    BACKGROUND: For evaluating patients with aortic regurgitation (AR), regurgitant volumes, left ventricular (LV) stroke volumes (SV), and absolute LV volumes are valuable indices. AIM: The aim of this study was to validate the combination of real-time 3-dimensional echocardiography (3DE) and semiautomated digital color Doppler cardiac flow measurement (ACM) for quantifying absolute LV volumes, LVSV, and AR volumes using an animal model of chronic AR and to investigate its clinical applicability. METHODS: In 8 sheep, a total of 26 hemodynamic states were obtained pharmacologically 20 weeks after the aortic valve noncoronary (n = 4) or right coronary (n = 4) leaflet was incised to produce AR. Reference standard LVSV and AR volume were determined using the electromagnetic flow method (EM). Simultaneous epicardial real-time 3DE studies were performed to obtain LV end-diastolic volumes (LVEDV), end-systolic volumes (LVESV), and LVSV by subtracting LVESV from LVEDV. Simultaneous ACM was performed to obtain LVSV and transmitral flows; AR volume was calculated by subtracting transmitral flow volume from LVSV. In a total of 19 patients with AR, real-time 3DE and ACM were used to obtain LVSVs and these were compared with each other. RESULTS: A strong relationship was found between LVSV derived from EM and those from the real-time 3DE (r = 0.93, P <.001, mean difference (3D - EM) = -1.0 +/- 9.8 mL). A good relationship between LVSV and AR volumes derived from EM and those by ACM was found (r = 0.88, P <.001). A good relationship between LVSV derived from real-time 3DE and that from ACM was observed (r = 0.73, P <.01, mean difference = 2.5 +/- 7.9 mL). In patients, a good relationship between LVSV obtained by real-time 3DE and ACM was found (r = 0.90, P <.001, mean difference = 0.6 +/- 9.8 mL). CONCLUSION: The combination of ACM and real-time 3DE for quantifying LV volumes, LVSV, and AR volumes was validated by the chronic animal study and was shown to be clinically applicable.

  1. Identification of key peptidoglycan hydrolases for morphogenesis, autolysis, and peptidoglycan composition of Lactobacillus plantarum WCFS1

    Rolain Thomas

    2012-10-01

    Full Text Available Abstract Background Lactobacillus plantarum is commonly used in industrial fermentation processes. Selected strains are also marketed as probiotics for their health beneficial effects. Although the functional role of peptidoglycan-degrading enzymes is increasingly documented to be important for a range of bacterial processes and host-microbe interactions, little is known about their functional roles in lactobacilli. This knowledge holds important potential for developing more robust strains resistant to autolysis under stress conditions as well as peptidoglycan engineering for a better understanding of the contribution of released muramyl-peptides as probiotic immunomodulators. Results Here, we explored the functional role of the predicted peptidoglycan hydrolase (PGH complement encoded in the genome of L. plantarum by systematic gene deletion. From twelve predicted PGH-encoding genes, nine could be individually inactivated and their corresponding mutant strains were characterized regarding their cell morphology, growth, and autolysis under various conditions. From this analysis, we identified two PGHs, the predicted N-acetylglucosaminidase Acm2 and NplC/P60 D,L-endopeptidase LytA, as key determinants in the morphology of L. plantarum. Acm2 was demonstrated to be required for the ultimate step of cell separation of daughter cells, whereas LytA appeared to be required for cell shape maintenance and cell-wall integrity. We also showed by autolysis experiments that both PGHs are involved in the global autolytic process with a dominant role for Acm2 in all tested conditions, identifying Acm2 as the major autolysin of L. plantarum WCFS1. In addition, Acm2 and the putative N-acetylmuramidase Lys2 were shown to play redundant roles in both cell separation and autolysis under stress conditions. Finally, the analysis of the peptidoglycan composition of Acm2- and LytA-deficient derivatives revealed their potential hydrolytic activities by the

  2. The prognostic value of sST2 and galectin-3 considering different aetiologies in non-ischaemic heart failure.

    Binas, David; Daniel, Hanna; Richter, Anette; Ruppert, Volker; Schlüter, Klaus-Dieter; Schieffer, Bernhard; Pankuweit, Sabine

    2018-01-01

    Several studies indicate a prognostic value of sST2 and galectin-3 in heart failure (HF). While previous studies focused on ischaemic cause of HF, we investigated the role of sST2 and galectin-3 in patients with non-ischaemic dilated cardiomyopathy (DCM). sST2 and galectin-3 serum concentrations were measured in 262 subjects with DCM. Survival rates were determined for all-cause mortality (ACM) and cardiac mortality (CM). In a univariate model, sST2 as a continuous variable was a predictor of ACM (HR 1.05; 95% CI 1.03 to 1.07, PACM (HR 1.10; 95% CI 1.05 to 1.17, PACM (HR 1.04; 95% CI 1.01 to 1.07, P=0.019) was significant. In a multivariate model, the prognostic value of the sST2 main group remained intact for ACM (HR 1.04; 95% CI 1.02 to 1.07, P=0.003).Univariate and multivariate analysis of galectin-3 as continuous variable did not show any significant result. However, in a quartile model, intermediate values of galectin-3 were significantly associated with a lower event rate of ACM and CM. The study revealed that sST2 predicts ACM and CM in patients with non-ischaemic HF and could be useful especially in patients with inflammatory background. Our findings that intermediate levels of galectin-3 allow for better prognosis were new and different to other investigations. NCT03090425; Results.

  3. Phantom-Calibrated versus Automatic Coronary Artery Mass Quantification with Multidetector-Row Computed Tomography: In Vitro and In Vivo Study

    Serafin, Z.; Lasek, W.; Laskowska, K. (Dept. of Radiology and Diagnostic Imaging, Nicolaus Copernicus Univ., Collegium Medicum, Bydgoszcz (Poland))

    2008-11-15

    Background: Coronary artery calcium scoring is used as a method for cardiovascular risk stratification and monitoring of coronary heart disease. Automatic software-based calcium mass calculation has been proposed to improve the performance of the procedure. Purpose: To compare two algorithms of calcium mass measurement, automatic and phantom calibrated, with respect to correlation, measurement error, and accuracy in vitro and in vivo. Material and Methods: A cardiac phantom with calcium cylinder inserts was scanned with sequential non-overlapping collimation 4x2.5 mm, at 120 kV and 165 mAs. Fifty adults (37 men; mean age 46.2 years) were examined with the same settings using prospective electrocardiographic triggering to detect and quantify coronary artery calcifications. Calculations were performed with two methods: software-based automatic calcium mass measurement (ACM) and phantom-calibrated calcium mass measurement (CCM). Results: The total phantom calcium masses measured with ACM and CCM were 175.0+-13.8 mg and 163.0+-4.4 mg, respectively (P<0.0001), and ACM produced a higher mean error (4.5 vs. 3.2; P<0.05). Results of ACM and CCM were strongly correlated to each other (R=0.73-0.96; P<0.0001). Mean image noise in the patient study was 8.72+-1.68 HU. Results of patient calcium scoring with ACM and CCM were significantly different (median 70.3 mg and 59.7 mg, respectively; P<0.0001), with a mean systematic error of 17.5% (limit of agreement between 14.6% and 20.4%). The use of ACM resulted in an altered quartile classification for 14% of patients, as compared to CCM; all of these patients were classified into a higher category. Conclusion: Our data indicate that multidetector-row computed tomography coronary calcium mass determination based on dedicated phantom calibration shows lower measurement error than an automatic software-based calculation method. The tested automatic software does not yet seem to be a reliable option for calcium mass measurement

  4. Phantom-Calibrated versus Automatic Coronary Artery Mass Quantification with Multidetector-Row Computed Tomography: In Vitro and In Vivo Study

    Serafin, Z.; Lasek, W.; Laskowska, K.

    2008-01-01

    Background: Coronary artery calcium scoring is used as a method for cardiovascular risk stratification and monitoring of coronary heart disease. Automatic software-based calcium mass calculation has been proposed to improve the performance of the procedure. Purpose: To compare two algorithms of calcium mass measurement, automatic and phantom calibrated, with respect to correlation, measurement error, and accuracy in vitro and in vivo. Material and Methods: A cardiac phantom with calcium cylinder inserts was scanned with sequential non-overlapping collimation 4x2.5 mm, at 120 kV and 165 mAs. Fifty adults (37 men; mean age 46.2 years) were examined with the same settings using prospective electrocardiographic triggering to detect and quantify coronary artery calcifications. Calculations were performed with two methods: software-based automatic calcium mass measurement (ACM) and phantom-calibrated calcium mass measurement (CCM). Results: The total phantom calcium masses measured with ACM and CCM were 175.0±13.8 mg and 163.0±4.4 mg, respectively (P<0.0001), and ACM produced a higher mean error (4.5 vs. 3.2; P<0.05). Results of ACM and CCM were strongly correlated to each other (R=0.73-0.96; P<0.0001). Mean image noise in the patient study was 8.72±1.68 HU. Results of patient calcium scoring with ACM and CCM were significantly different (median 70.3 mg and 59.7 mg, respectively; P<0.0001), with a mean systematic error of 17.5% (limit of agreement between 14.6% and 20.4%). The use of ACM resulted in an altered quartile classification for 14% of patients, as compared to CCM; all of these patients were classified into a higher category. Conclusion: Our data indicate that multidetector-row computed tomography coronary calcium mass determination based on dedicated phantom calibration shows lower measurement error than an automatic software-based calculation method. The tested automatic software does not yet seem to be a reliable option for calcium mass measurement

  5. Direct Observation of High-Temperature Superconductivity in One-Unit-Cell FeSe Films

    Zhang Wen-Hao; Zhang Jin-Song; Li Fang-Sen; Guo Ming-Hua; Ding Hao; Tang Chen-Jia; Wang Qing-Yan; He Ke; Ji Shuai-Hua; Chen Xi; Sun Yi; Zhao Yan-Fei; Xing Ying; Wang Hui-Chao; Zhang Hui-Min; Peng Jun-Ping; Li Zhi; Wang Meng; Fujita Takeshi; Hirata Akihiko

    2014-01-01

    We prepared one-unit-cell (1-UC) thick FeSe films on insulating SrTiO 3 substrates with non-superconducting FeTe protection layers by molecular beam epitaxy for ex situ studies. By direct transport and magnetic measurements, we provide definitive evidence for high temperature superconductivity in the 1-UC FeSe films with an onset T C above 40 K and an extremely large critical current density J C ∼1.7×10 6 A/cm 2 at 2 K, which are much higher than T C ∼8 K and J C ∼10 4 A/cm 2 for bulk FeSe, respectively. Our work may pave the way to enhancing and tailoring superconductivity by interface engineering. (express letter)

  6. Development of aerodynamic bearing support for application in air cycle machines

    Šimek J.

    2014-06-01

    Full Text Available Air cycle machines (ACM are used in environmental control system of aircrafts to manage pressurization of the cabin. The aim of this work is to gain theoretical and experimental data enabling replacement of rolling bearings, which require lubrication and have limited operating speed, with aerodynamic bearing support. Aerodynamic bearings do not pollute process air and at the same time allow achieving higher operating speed, thus enabling to reduce machine mass and dimensions. A test stand enabling the verification of aerodynamic bearing support properties for prospective ACM was designed, manufactured and tested with operating speeds up to 65 000 rpm. Some interesting features of the test stand design and the test results are presented. A smaller test stand with operating speed up to 100 000 rpm is in design stage.

  7. Generation of intense ion beams and their application to controlled fusion research

    Dreike, P.; Ferch, R.L.; Friedman, A.

    1977-01-01

    Successful generation of pulsed multi-kA proton beams in the energy range 0.2 to 1.7 MeV using existing pulsed power technology has been achieved by three different techniques: reflex triodes, pinched electron-beam diodes and magnetically insulated diodes. Peak current densities in excess of 10 kAcm -2 have been observed on the NRL Gamble II machine and over 1.0 kAcm -2 on the Cornell Neptune machine. Peak total ion currents above 200 kA are produced by Gamble II. The potential applications of intense ion beams to magnetic confinement include (i) plasma heating and (ii) ion rings. A summary of continuous theoretical and experimental investigations on these applications is presented. (author)

  8. KrF laser kinetics studies

    Mandl, A.; Klimek, D.; Parks, J.H.

    1984-01-01

    A series of measurements characterizing an e beam pumped KrF* laser was carried out using a 200-nsec e-beam pulse having a rise time of 25 nsec at current densities up to 50 A/cm 2 . These pump conditions are relevent for inertial confinement fusion laser drivers. The measurements include fluorescence efficiency, sidelight suppression of the fluorescence during lasing, and laser energy output over a wide range of laser parameters including: total density 0.5--2.0 amagats, temperature 300--400 K, fluorine density 0.15%--0.5%, current density 38--50 A/cm 2 and various mirror transmissions. This data was used to verify and refine a model of KrF* kinetics which was then used to estimate the performance of an angular multiplexed power amplifier suitable for laser fusion applications

  9. Development of bipolar pulse accelerator for intense pulsed ion beam acceleration

    Fujioka, Y.; Mitsui, C.; Kitamura, I.; Takahashi, T.; Masugata, K.; Tanoue, H.; Arai, K.

    2003-01-01

    To improve the purity of an intense pulsed ion beams a new type of pulsed ion beam accelerator named 'bipolar pulse accelerator (BPA)' was proposed. In the accelerator purity of the beam is expected. To confirm the principle of the accelerator experimental system was developed. The system utilizes B y type magnetically insulated acceleration gap and operated with single polar negative pulse. A coaxial gas puff plasma gun placed in the grounded anode was used as an ion source, and source plasma (nitrogen) of current density approx. = 25 A/cm 2 , duration approx. = 1.5 μs was injected into the acceleration gap. The ions are successfully accelerated from the grounded anode to the drift tube by applying negative pulse of voltage 180 kV, duration 60 ns to the drift tube. Pulsed ion beam of current density approx. = 40 A/cm 2 , duration approx. 60 ns was obtained at 42 mm downstream from the anode surface. (author)

  10. Preparation and properties of superconducting Bi-Sr-Ca-Cu-O materials by the alkoxide process

    Uchikawa, Fusaoki; Kobayashi, Toshio; Usami, Ryo; Yoshizaki, Kiyoshi

    1989-01-01

    Homogeneous starting solutions were synthesized using Bi, Sr, Ca and Cu alkoxides. Powders, thick films and gel fibers were prepared respectively by controlling hydrolysis using the same solutions. The synthesized powder had a homogeneous particle size. The fired powder showed a good crystallization property. The thick film coated on MgO substrate using the synthesized sol solution had a smooth surface and a uniformity of each metal elements. The film showed the c-axis orientation and was shown to have the zero resistance temperature of 90 K and the critical current density of 180 A/cm 2 at 77 K. The fiber drawn from the viscous gel solution showed a comparatively large shrinkage with hear treatment. The fired fiber was brittle and had a low strength. It was also found for the fired fiber that zero resistance temperature was 70 K and the critical current density was 90 A/cm 2 at 77 K

  11. Importance of controlling the Tl-oxide partial pressure throughout the processing of TlBa2CaCu2O7 thin films

    Siegal, M.P.; Venturini, E.L.; Newcomer, P.P.; Overmyer, D.L.; Dominguez, F.; Dunn, R.

    1995-01-01

    TlBa 2 CaCu 2 O 7 (Tl-1212) superconducting films 5000--6000 A thick have been grown on LaAlO 3 (100) substrates using oxide precursors in a closed two-zone thallination furnace. Tl-1212 films can be grown with transition temperatures ∼100 K, and critical current densities measured by magnetization of J cm (5 K)>10 7 A/cm 2 and J cm (77 K)>10 5 A/cm 2 . Processing conditions, substrate temperatures and Tl-oxide source temperatures are found which result in smooth, nearly phase-pure Tl-1212 films. Variations in the respective temperature ramps of the Tl-oxide zone and the substrate zone can greatly influence resulting film properties such as microstructure, morphology, superconducting transition temperature, and critical current density. copyright 1995 American Institute of Physics

  12. Grain size dependence of the critical current density in YBa2Cu3Ox superconductors

    Kuwabara, M.; Shimooka, H.

    1989-01-01

    The grain size dependence of the critical current density in bulk single-phase YBa 2 Cu 3 O x ceramics was investigated. The grain size of the materials was changed to range approximately from 1.0 to 25 μm by changing the conditions of power processing and sintering, associated with an increase in the sintered density of the materials with increasing grain size. The critical current density has been found to exhibit a significant grain size dependence, changing from 880 A/cm 2 to a value of 100 A/cm 2 with a small increase in the average grain size from 1.2 to 2.0 μm. This seems to provide information about the nature of the weak link between superconducting grains which might govern the critical current density of the materials

  13. Transport measurements on superconducting YBa2Cu3O7-δ thin film lines

    Moeckly, B.H.; Lathrop, D.K.; Redinbo, G.F.; Russek, S.E.; Buhrman, R.A.

    1990-01-01

    Critical current densities, magnetic field response, and microwave response have been measured for laser ablated YBa 2 Cu 3 O 7-δ thin film lines on MgO and SrTiO 3 substrates. Films on SrTiO 3 have critical current densities > 1 x 10 6 A/cm 2 at 77 K and show uniform transport properties in lines of all sizes. Films on MgO have critical current densities which range between 10 2 and 10 6 A/cm 2 at 77 K and show considerable variation from device to device on the same chip. Narrow lines on MgO with low critical current densities show Josephson weak link structure which includes RSJ-like IV curves, microwave induced constant voltage steps, and a high sensitivity to magnetic field. The presence of the Josephson weak links if correlated with small amounts of misaligned grains in film on MgO

  14. A Decade of Solid Oxide Electrolysis Improvements at DTU Energy

    Hauch, Anne; Brodersen, Karen; Chen, Ming

    2017-01-01

    a short review of the R&D work on SOEC single cells conducted at DTU Energy from 2005 to 2015. The SOEC improvements have involved increasing the of the oxygen electrode performance, elimination of impurities in the feed streams, optimization of processing routes, and fuel electrode structure optimization....... All together, these improvements have led to a decrease in long-term degradation rate from ∼40 %/kh to ∼0.4 %/kh for steam electrolysis at -1 A/cm2, while the initial area specific resistance has been decreased from 0.44 Ωcm2 to 0.15 Ωcm2 at -0.5 A/cm2 and 750 °C....

  15. Impulse response measurement in the HgCdTe avalanche photodiode

    Singh, Anand; Pal, Ravinder

    2018-04-01

    HgCdTe based mid-wave infrared focal plane arrays (MWIR FPAs) are being developed for high resolution imaging and range determination of distant camouflaged targets. Effect of bandgap grading on the response time in the n+/ν/p+ HgCdTe electron avalanche photodiode (e-APD) is evaluated using impulse response measurement. Gain normalized dark current density of 2 × 10-9 A/cm2 at low reverse bias for passive mode and 2 × 10-4 A/cm2 at -8 V for active mode is measured in the fabricated APD device, yielding high gain bandwidth product of 2.4 THZ at the maximum gain. Diffusion of carriers is minimized to achieve transit time limited impulse response by introducing composition grading in the HgCdTe epilayer. The noise equivalent photon performance less than one is achievable in the FPA that is suitable for active cum passive imaging applications.

  16. Characteristics of scandate-impregnated cathodes with sub-micron scandia-doped matrices

    Yuan Haiqing; Gu Xin; Pan Kexin; Wang Yiman; Liu Wei; Zhang Ke; Wang Jinshu; Zhou Meiling; Li Ji

    2005-01-01

    We describe in this paper scandate-impregnated cathodes with sub-micron scandia-doped tungsten matrices having an improved uniformity of the Sc distribution. The scandia-doped tungsten powders were made by both liquid-solid doping and liquid-liquid doping methods on the basis of previous research. By improving pressing, sintering and impregnating procedures, we have obtained scandate-impregnated cathodes with a good uniformity of the Sc 2 O 3 - distribution. The porosity of the sub-micron structure matrix and content of impregnants inside the matrix are similar to those of conventionally impregnated cathodes. Space charge limited current densities of more than 30 A/cm 2 at 850 deg. C b have been obtained in a reproducible way. The current density continuously increases during the first 2000 h life test at 950 deg. C b with a dc load of 2 A/cm 2 and are stable for at least 3000 h

  17. Critical current density and flux pinning in superconducting wires and coils of silver-clad Bi-Pb-Sr-Ca-Cu-O

    Dou, S.X.; Liu, H.K.; Apperley, M.H.; Song, K.H.; Sorrell, C.C.; Guo, S.J.; Loberg, B.; Easterling, K.E.

    1991-01-01

    The critical current density (J c ) of Ag-clad of Bi-Pb-Sr-Ca-Cu-O has been measured to be about 12,000 A/cm 2 at 77 K in zero field. This wire was rolled into a tape of thickness 0.1 mm and width of 2 to 3 mm, and a coil of 35 mm diameter was formed. The J c of this coil was measured to be about 2,000 A/cm 2 at 77 K over the full length (1.00 meter) of the coil. In this paper compositions, heat treatment parameters, and cold-deformation for enhancement of J c are presented. The microstructure is characterized and pinning interactions as well as possible weak links are emphasised. (orig.)

  18. Beta-blocker subtype and risks of perioperative adverse events following non-cardiac surgery

    Jørgensen, Mads E.; Sanders, Robert D.; Køber, Lars

    2017-01-01

    Aims Beta-blockers vary in pharmacodynamics and pharmacokinetic properties. It is unknown whether specific types are associated with increased perioperative risks. We evaluated perioperative risks associated with beta-blocker subtypes, overall and in patient subgroups. Methods and results We...... performed a Danish Nationwide cohort study, 2005-2011, of patients treated chronically with beta blocker (atenolol, bisoprolol, carvedilol, metoprolol, propranolol, or other) prior to non-cardiac surgery. Risks of 30-day all-cause mortality (ACM) and 30-day major adverse cardiovascular events (MACE) were...... in analyses stratified by age, surgery priority, duration of anaesthesia or surgery risk (all P for interaction >0.05). Conclusion Risks of ACM and MACE did not systematically differ by beta-blocker subtype. Findings may guide clinical practice and future trials....

  19. Foreword

    Chrysanthis, P. K.; Jensen, Christian Søndergaard; Kumar, V.

    2006-01-01

    it is our great pleasure to welcome you all to the Fifth ACM International Workshop on Data Engineering for Wireless and Mobile Access (MobiDE 2006), which is held in conjunction with ACM SIGMOD/PODS 2006. This workshop brings together researchers in databases, networking, and mobile computing...... of very high quality, making the selection process quite competitive. All submissions were reviewed by at least 3 members of the Program Committee. This was followed by a discussion phase, where the reviewers of each submission had the opportunity to discuss the submission and its reviews. As a result, 10...... in the program. This talk probes into the consumer side of the mobile environment.The program reflects the depth and breadth of the field, with sessions covering important aspects of mobility, location-based processing, and the introduction of sensor technology into the real world. Thus, these proceedings...

  20. Development of application technique of bulk high-Tc superconductor

    Hong, Kye Won; Kim, Chan Joong; Kim, Kee Baek; Kwon, Sun Chil; Won, Dong Yun; Lee, Hoh Jin; Lee, Heui Kyoon; Jang, Kun Ik; Yang, Suk Woo

    1995-03-01

    YBCO-Ag composite superconductors were prepared by extrusion using inorganic binder materials. In the case of the undoped 1-2-3 sample with a dia. of 2.5 mm, critical current density (Jc) was 150 A/cm 2 and current density (Ic) was 10 amps. In the case of the sample with a die. of 4.5 mm, meanwhile, Jc and Ic were 50 A/cm 2 and 32 amps, respectively. Influence of BaCeO 3 addition on magnetization characteristics of melt-textured Y-Ba-Cu-O superconductor was investigated. The variation of magnetization behavior due to the addition of BaCeO 3 is discussed on the basis of the related microstructures. 37 figs, 1 tab, 56 refs. (Author)

  1. Unbalanced Cylindrical Magnetron for Accelerating Cavities Coating

    Rosaz, Guillaume; Calatroni, Sergio; Sublet, Alban; Tobarelli, Mauro

    2016-01-01

    We report in this paper the design and qualification of a cylindrical unbalanced magnetron source. The dedicated magnetic assemblies were simulated using a finite element model. A hall-effect magnetic probe was then used to characterize those assemblies and compared to the theoretical magnet profiles. These show a good agreement between the expected and actual values. the qualification of the different magnetic assemblies was then performed by measuring the ion flux density reaching the surface of the sample to be coated using a commercial retarding field energy analyzer. The strongest unbalanced configuration shows an increase from 0.016A.cm^-2 to 0.074A.cm^-2 of the ion flux density reaching the sample surface compared to the standard balanced configuration for a pressure 5.10^-3 mbar and a plasma source power of 300W.

  2. Stability of magnets levitated above superconductors

    Davis, L.C.; Logothetis, E.M.; Soltis, R.E.

    1988-01-01

    The stability of a permanent magnet levitated above a slab of hard superconductor is considered. The force on a dipole magnet over a perfectly diamagnetic disk is calculated. It is found that the radial component of the force is directed outward and is 10%--20% of the image (vertical) force near the edge. Estimates of the magnetic friction force due to flux motion in a hard superconductor are made using Bean's model. The magnitude of the magnetic friction is large enough to stabilize the magnet over most of the disk for typical values of the critical current in ceramic superconductors (∼10 3 A/cm 2 ), but too small for the highest values reported (>10 6 A/cm 2 ). It is conjectured that flux trapping due to inhomogeneities gives rise to transient restoring forces

  3. Generating and exploring good building layouts

    Bao, Fan

    2013-07-16

    Good building layouts are required to conform to regulatory guidelines, while meeting certain quality measures. While different methods can sample the space of such good layouts, there exists little support for a user to understand and systematically explore the samples. Starting from a discrete set of good layouts, we analytically characterize the local shape space of good layouts around each initial layout, compactly encode these spaces, and link them to support transitions across the different local spaces. We represent such transitions in the form of a portal graph. The user can then use the portal graph, along with the family of local shape spaces, to globally and locally explore the space of good building layouts. We use our framework on a variety of different test scenarios to showcase an intuitive design, navigation, and exploration interface. Copyright © ACM. Copyright © ACM 2013.

  4. MgO by injection CVD

    Abrutis, A.; Kubilius, V.; Teiserkis, A.; Bigelyte, V.; Vengalis, B.; Jukna, A.; Butkute, R.

    1997-01-01

    Epitaxial YBa 2 Cu 3 O 7 layers with 45 in-plane orientation have been grown by injection CVD on MgO substrates polished off-axis to within 1.4-1.9 of the [100] direction. This new single-source CVD process is based on computer-controlled injection of precise microdoses of a metal-organic precursor solution into a CVD reactor. A wide range of solution compositions was tested to investigate compositional effects on phase purity, surface morphology, texturing and superconducting properties of the prepared films. The highest quality films with pure 45 texture had a smooth surface, zero resistance T c (R=0) of 88-89 K, and critical current density J c (77 K) above 10 6 A/cm 2 . (orig.) and critical current density J c (77 K) above 10 6 A/cm 2 . (orig.)

  5. Solid Oxide Electrolyser Cell

    Jensen, Søren Højgaard

    Solid oxide fuel cells (SOFCs) produced at Risø National Laboratory was tested as steam electrolysers under various current densities, operating temperatures and steam partial pressures. At 950 °C and a cell voltage of 1.48V the current density was -3.6A/cm2 with app. 30% H2 + 70% H2O in the inlet...... it is possible to achieve a production price of 0.7 US$/kg H2 with an electricity price of 1.3 US¢/kWh. The cell voltage was measured as function of time. In test ofabout two month of duration a long-term degradation was observed. At 850 °C, -0.5 A/cm2 with 50 vol% H2 the degradation rate was app. 20 mV/1000h...

  6. Implementación de un método de purificación consistente y virológicamente seguro del anticuerpo monoclonal CB.Hep-1 empleado en la purificación el antígeno de superficie del virus de la hepatitis B

    Valdés Véliz, Rodolfo

    2007-01-01

    Aborda la implementación de un método eficiente y consistente para la purificación del anticuerpo monoclonal (AcM) CB.Hep-1 empleado en la purificación del antígeno de superficie del virus de la Hepatitis B (AgsVHBr), así como la demostración de su capacidad de eliminación de virus. También se exploró la potencialidad del tratamiento térmico del AgsVHBr en presencia de KSCN para inactivar virus. El empleo de este AcM brinda una alta selectividad y originalidad al método de obtención del AgsVH...

  7. Interfacial characteristics and dielectric properties of Ba0.65Sr0.35TiO3 thin films

    Quan Zuci; Zhang Baishun; Zhang Tianjin; Zhao Xingzhong; Pan Ruikun; Ma Zhijun; Jiang Juan

    2008-01-01

    Ba 0.65 Sr 0.35 TiO 3 (BST) thin films were deposited on Pt/Ti/SiO 2 /Si substrates by radio frequency magnetron sputtering technique. X-ray photoelectron spectroscopy (XPS) depth profiling data show that each element component of the BST film possesses a uniform distribution from the outermost surface to subsurface, but obvious Ti-rich is present to BST/Pt interface because Ti 4+ cations are partially reduced to form amorphous oxides such as TiO x (x -7 A/cm 2 at 1.23 V and lower than 5.66 x 10 -6 A/cm 2 at 2.05 V as well as breakdown strength is above 3.01 x 10 5 V/cm

  8. Critical current density, irreversibility line, and flux creep activation energy in silver-sheathed Bi2Sr2Ca2Cu3Ox superconducting tapes

    Shi, D.; Wang, Z.; Sengupta, S.; Smith, M.; Goodrich, L.F.; Dou, S.X.; Liu, H.K.; Guo, Y.C.

    1992-08-01

    Transport data, magnetic hysteresis and flux creep activation energy experimental results are presented for silver-sheathed high-T c Bi 2 Sr 2 Ca 2 Cu 3 O x superconducting tapes. The 110 K superconducting phase was formed by lead doping in a Bi-Sr-Ca-Cu-0 system. The transport critical current density was measured at 4.0 K to be 0.7 x 10 5 A/cm 2 (the corresponding critical current is 74 A) at zero field and 1.6 x 10 4 A/cm 2 at 12 T for H parallel ab. Excellent grain alignment in the a-b plane was achieved by a short-melting method, which considerably improved the critical current density and irreversibility line. Flux creep activation energy as a function of current is obtained based on the magnetic relaxation measurements

  9. A study on the development of high Tc superconducting materials and on the effects of neutron irradiation

    Won, Dong Yeon; Chang, In Soon; Lee, Jong Min

    1990-08-01

    An Ag-sheathed (Pb,Bi)SrCaCuO superconducting tape was prepared by the cold rolling and post heat treatment method. The tape shows a c-oriented texture perpendicular to the rolling direction. The aligned grain structure may be resulted from the anisotropic grain growth of the high Tc superconducting phase. The bulk (Pb,Bi)SrCaCuO samples with (a) Tc=10lK and (b) 96K were prepared by the solid state reaction method and were neutron-irradiated up to 1.5 x 10 1 8 n/cm 2 . After irradiation the zero resistance temperature(Tc) of (a) was decreased to 96K but (b) did not show any change in Tc. The critical current density of (a) also decreased from 0.75A/cm 2 but (b) was constant as 1.5 A/cm 2 after irradiation. (Author)

  10. Internal currents in PEMFC during start-up or shut-down

    Maranzana, G.; Lottin, O.; Moyne, C.; Dillet, J.; Lamibrac, A.; Mainka, J.; Didierjean, S. [Nancy Univ. - CNRS (France). LEMTA

    2010-07-01

    Experiments show that the internal currents that occur during PEMFC start-up can reach up to 1 Acm{sup -2}. This is far more important than the expected order of magnitude of the current densities associated with carbon oxidation, which is only of a few mAcm{sup -2}. The predominant phenomenon that explains the internal currents is the charge and discharge of the double layer capacitances. A simple model with constant values of the electric parameters yields numerical results close to the experimental ones. It also explains the transient voltage rise (over the steady state open circuit voltage) that is sometimes observed experimentally shortly after the fuel cell start up. (orig.)

  11. A novel type of self-beating cardiomyocytes in adult mouse ventricles

    Omatsu-Kanbe, Mariko; Matsuura, Hiroshi

    2009-01-01

    This study was designed to investigate the presence of resident heart cells that are distinct from terminally-differentiated cardiomyocytes. Adult mouse heart was coronary perfused with collagenase, and ventricles were excised and further digested. After spinning cardiomyocyte-containing fractions down, the supernatant fraction was collected and cultured without adding any chemicals. Two to five days after plating, some of rounded cells adhered to the culture dish, gradually changed their shape and then started self-beating. These self-beating cells did not appreciably proliferate but underwent a further morphological maturation process to form highly branched shapes with many projections. These cells were mostly multinucleated, well sarcomeric-organized and expressed cardiac marker proteins, defined as atypically-shaped cardiomyocytes (ACMs). Patch-clamp experiments revealed that ACMs exhibited spontaneous action potentials arising from the preceding slow diastolic depolarization. We thus found a novel type of resident heart cells in adult cardiac ventricles that spontaneously develop into self-beating cardiomyocytes.

  12. Numerical analysis of boosting scheme for scalable NMR quantum computation

    SaiToh, Akira; Kitagawa, Masahiro

    2005-01-01

    Among initialization schemes for ensemble quantum computation beginning at thermal equilibrium, the scheme proposed by Schulman and Vazirani [in Proceedings of the 31st ACM Symposium on Theory of Computing (STOC'99) (ACM Press, New York, 1999), pp. 322-329] is known for the simple quantum circuit to redistribute the biases (polarizations) of qubits and small time complexity. However, our numerical simulation shows that the number of qubits initialized by the scheme is rather smaller than expected from the von Neumann entropy because of an increase in the sum of the binary entropies of individual qubits, which indicates a growth in the total classical correlation. This result--namely, that there is such a significant growth in the total binary entropy--disagrees with that of their analysis

  13. Microstructural analyses and critical current densities in the high-Tc superconductor system ReBa2Cu3OX, with RE = Y, Sm, Eu, Gd, Dy, Ho

    Schindler, G.; Seebacher, B.

    1989-01-01

    The authors report on investigations into the impact of the rare earths (RE) as given in the title on the ceramic microstructure and the critical current density j c in the superconductor system REBa 2 Cu 3 O x . With RE = Sm, Eu, or Gd, the material is homogeneous in phase and crystallizes in platelets with maximum sizes of up to 350 μm. Material with RE = Y, Dy, or Ho exhibits grain sizes up to 500 μm, and a low amount of phase inhomogeneities. The critical currents measured are between 25 Acm -2 and 290 Acm -2 at 77 K, without external field. The highest values are found in systems with RE = Eu or Gd. (orig.) [de

  14. BOA II: Asbestos Pipe-Insulation Removal Robot System. Innovative Technology Summary Report

    None

    2001-01-01

    The objective of this task is to develop and demonstrate a mechanical, asbestos-removal system that can be remotely operated without a containment area. The technology, known as BOA, consists of a pipe-crawler removal head and a boom vehicle system with dual robots. BOA's removal head can be remotely placed on the outside of the pipe and can crawl along the pipe, removing lagging and insulation. The lagging and insulation is cut using a hybrid endmill water-jet cutter and then diced into 2-inch cube sections of ACM. These ACM sections are then removed from the pipe using a set of blasting fan- spray nozzles, vacuumed off through a vacuum hose, and bagged. Careful attention to vacuum and entrapment air flow ensures that the system can operate without a containment area while meeting local and federal standards for fiber count

  15. Experimental Tests of the Algebraic Cluster Model

    Gai, Moshe

    2018-02-01

    The Algebraic Cluster Model (ACM) of Bijker and Iachello that was proposed already in 2000 has been recently applied to 12C and 16O with much success. We review the current status in 12C with the outstanding observation of the ground state rotational band composed of the spin-parity states of: 0+, 2+, 3-, 4± and 5-. The observation of the 4± parity doublet is a characteristic of (tri-atomic) molecular configuration where the three alpha- particles are arranged in an equilateral triangular configuration of a symmetric spinning top. We discuss future measurement with electron scattering, 12C(e,e’) to test the predicted B(Eλ) of the ACM.

  16. Measurements on very small single crystals of NdFeB using a vibrating reed magnetometer

    Richter, H.J.; Hempel, K.A.; Verhoef, R.

    1988-01-01

    Nd 2 Fe 14 B single crystals with magnetic moments ranging from 1.6 x 10 -8 Acm 2 to 9.5 x 10 -7 Acm 2 are measured using the ultra high sensitivity vibrating reed magnetometer. The hysteresis loops are compared to those of BaFe 12 O 19 single crystals. It turns out that the magnetization reversal of the Nd 2 Fe 14 B samples is similar to that of BaFe 12 O 19 single crystals if the ferrite samples are considerably bigger in size. This does not hold for bigger Nd 2 Fe 14 B particles where stronger domain wall pinning is observed. For very small grains of Nd 2 Fe 14 B there is still evidence of domain wall processes while for BaFe 12 O 19 grains of the same size true single domain behaviour can be observed

  17. Out-of-plane tilted Josephson junctions of bi-epitaxial YBa2Cu3O x thin films on tilted-axes NdGaO3 substrates with CeO2 seeding layer

    Mozhaev, Peter B.; Mozhaeva, Julia E.; Bdikin, Igor K.; Kotelyanskii, Iosif M.; Luzanov, Valery A.; Zybtsev, Sergey G.; Hansen, Jorn Bindslev; Jacobsen, Claus S.

    2006-01-01

    Bi-epitaxial heterostructures YBa 2 Cu 3 O x (YBCO)/CeO 2 /NdGaO 3 were prepared on tilted-axes NdGaO 3 substrates using laser ablation technique. The heterostructures were patterned for electrical measurements using photolithography and ion-beam milling. Electrical anisotropy of the YBCO film was tested on the ion-beam etched surface. Bi-epitaxial junctions with four different orientations of the bi-epitaxial border were fabricated and studied. The measured I V curves showed flux-flow behavior with critical current density 2.5 x 10 4 A/cm 2 for the twist-type junctions and 1.5 x 10 3 A/cm 2 for [1 0 0]-tilt type junctions

  18. Influence of a transport current on the local magnetic field distribution in sintered YBa2Cu3Ox

    Zimmermann, P.; Keller, H.; Kuendig, W.; Puempin, B.; Savic, I.M.; Schneider, J.W.; Simmler, H.; Kaldis, E.; Rusiecki, S.

    1991-01-01

    The influence of a transport current on the magnetic flux-line distribution in sintered YBCO was studied by means of μSR. Pronounced differences between zero-field-cooled (ZFC) and field-cooled (FC) signals and irreversible behavior were observed. In the ZFC case even a small transport current (10 A/cm 2 ) tends to order irreversibly the inhomogeneous flux-line distribution considerably, suggesting a broad distribution of pinning barriers. However, for a FC sample no noticeable change in the flux distribution in the presence of a transport current (up to 40 A/cm 2 ) was detected, indicating that the FC state represents a stable flux-line configuration. (orig.)

  19. Simultaneous Assessment of White Matter Changes in Microstructure and Connectedness in the Blind Brain

    Reislev, Nina Linde; Dyrby, Tim Bjørn; Siebner, Hartwig Roman

    2016-01-01

    Magnetic resonance imaging (MRI) of the human brain has provided converging evidence that visual deprivation induces regional changes in white matter (WM) microstructure. It remains unclear how these changes modify network connections between brain regions. Here we used diffusion-weighted MRI......) assessed the connectedness of each voxel with the rest of the brain. ACM yielded reduced anatomical connectivity in the corpus callosum in individuals with congenital but not late-onset blindness. ACM did not identify any brain region where blindness resulted in increased anatomical connectivity. DTI...... revealed widespread microstructural differences as indexed by a reduced regional fractional anisotropy (FA). Blind individuals showed lower FA in the primary visual and the ventral visual processing stream relative to sighted controls regardless of the blindness onset. The results show that visual...

  20. Earliest Results in the Use of Activated Composite Membranes for the Transport of Silver Ions from Aqueous Solutions

    Yucundo Mendoza-Tolentino

    2014-01-01

    Full Text Available This paper presents the results concerning the first use of activated composite membranes (ACMs for the facilitated transport of silver ions containing di-(2-ethylhexyl-dithiophosphoric acid (DTPA as the carrier. DTPA was immobilized by interfacial polymerization in a dense layer that was deposited in a porous layer, which was prepared on a nonwoven fabric support by phase inversion. The influence of fundamental parameters affecting the transport of silver ion as the carrier concentration in the membrane phase and stripping agent variation of the stripping solution have been studied. In the optimal conditions, the amount of silver transported across the ACMs was greater than 50%, whereas if the content of the carrier is modified, more than the 90% of the initial silver is removed from the feed phase.