POTENTIAL USE OF WOOL WASTE AS ADSORBENT FOR THE REMOVAL OF ACID DYES FROM WASTEWATER

Directory of Open Access Journals (Sweden)

BUCIŞCANU Ingrid

2016-05-01

Full Text Available At present, great amounts of raw wool are treated as waste and raise disposal problems. In the sustainable development context , wool is regarded as a biodegradable renewable resource and due to its complex chemical composition and fiber morphology, can find different useful applications. It is the aim of this paper to investigate the potential use of raw wool waste as a non-conventional adsorbent for Acid Red 337(AcR ,currently used for leather and wool dyeing. Two wool-based adsorbents were prepared, namely scoured coarse wool (Wool-S and wool activated with alcoholic solution of sodium hydroxide (Wool-A. Adsorbent dosage, dye concentration, pH and treatment time were factors taken in consideration for the assessment of the sorbate-adsorbent interaction. The removal efficiency (R % is mainly dependent on the solution pH and on the activation treatment applied to wool: at pH 3, the removal efficiency reaches the highest values of 42% on Wool-S and 99% on Wool-A. The adsorption rate is slow and needs almost 6 h to reach equilibrium. The experimental data best fitted the Langmuir equilibrium adsorption model, which proves that the adsorbent possess surface active sites to which the dye sorbate binds in monomolecular layer. Raw wool waste is a potential cheap, biodegradable and effective adsorbent for colored wastewater treatment.

Research on flame retardation of wool fibers

International Nuclear Information System (INIS)

Enomoto, Ichiro; Ametani, Kazuo; Sawai, Takeshi

1990-01-01

Flame retardant, vinyl phosphonate oligomer, was uniformly impregnated in wool fibers, and by irradiating low energy electron beam or cobalt-60 gamma ray, the flame retardation of fabrics was attempted, as the results, the following knowledges were obtained. At the rate of sticking of flame retardant lower than that in cotton fabrics, sufficient flame retarding property can be given. The flame retarding property withstands 30 times of washing. The lowering of strength due to the processing hardly arose. For the flame retardation, gamma-ray was more effective than electron beam. Since the accidents of burning clothes have occurred frequently, their flame retardation has been demanded. So far the flame retardation of cotton fabrics has been advanced, but this time the research on the flame retardation of wool fabrics was carried out by the same method. The experimental method is explained. As for the performance of the processed fabrics, the rate of sticking of the flame retardant, the efficiency of utilization, the flame retarding property, the endurance in washing and the tensile and tearing strength were examined. As the oxygen index was higher, the flame retarding property was higher, and in the case of the index being more than 27, the flame retarding property is sufficient, that is, the rate of sticking of 6% in serge and 5% in muslin. (K.I.)

Ultrasound for low temperature dyeing of wool with acid dye.

Science.gov (United States)

Ferrero, F; Periolatto, M

2012-05-01

The possibility of reducing the temperature of conventional wool dyeing with an acid levelling dye using ultrasound was studied in order to reach exhaustion values comparable to those obtained with the standard procedure at 98 °C, obtaining dyed samples of good quality. The aim was to develop a laboratory method that could be transferred at industrial level, reducing both the energy consumption and fiber damage caused by the prolonged exposure to high temperature without the use of polluting auxiliary agents. Dyeings of wool fabrics were carried out in the temperature range between 60 °C and 80 °C using either mechanical or ultrasound agitation of the bath and coupling the two methods to compare the results. For each dyeing, the exhaustion curves of the dye bath were determined and the better results of dyeing kinetics were obtained with ultrasound coupled with mechanical stirring. Hence the corresponding half dyeing times, absorption rate constants according to Cegarra-Puente modified equation and ultrasonic efficiency were calculated in comparison with mechanical stirring alone. In the presence of ultrasound the absorption rate constants increased by at least 50%, at each temperature, confirming the synergic effect of sonication on the dyeing kinetics. Moreover the apparent activation energies were also evaluated and the positive effect of ultrasound was ascribed to the pre-exponential factor of the Arrhenius equation. It was also shown that the effect of ultrasound at 60 °C was just on the dye bath, practically unaffecting the wool fiber surface, as confirmed by the results of SEM analysis. Finally, fastness tests to rubbing and domestic laundering yielded good values for samples dyed in ultrasound assisted process even at the lower temperature. These results suggest the possibility, thanks to the use of ultrasound, to obtain a well equalized dyeing on wool working yet at 60°C, a temperature process strongly lower than 98°C, currently used in industry

Eucalyptus oil-loaded microcapsules grafted to cotton fabrics for acaricidal effect against Dermatophagoides farinae.

Science.gov (United States)

Kim, Joo Ran

2017-05-01

The purpose of this study was to develop acaricidal cotton fabrics grafted with eucalyptus oil-loaded microcapsules (EOMCs) produced from green resources. EOMCs showed a broad size distribution between 0.5 and 6.5 μm, and had the average diameter 1.8 μm. EOMCs exhibited nonporous spherical shapes and individually remained on cotton fibres. Through AATCC mortality tests against house dust mites (HDMs) (Dermatophagoides farinae), the treated cotton fabric containing EOMCs resulted in 98.7% mortality. Acaricidal efficiency was due to the large amount of oxygenated monoterpene, 1,8-eucalyptol (75.8%) and hydroxylated monoterpenes such as α-terpineol (3.6%), terpinen-4-ol (0.4%) and linalool (0.3%) found in eucalyptus oil. These compounds are effective in enhancing penetration into HDMs. EOMCs produced from safe and natural sources can serve as a replacement for synthetic acaricides in controlling the population of HDM, leading to positive impacts on the human health and environment.

Optimization of acid-activated bentonites on bleaching of cotton oil

International Nuclear Information System (INIS)

Lacin, O.; Sayan, E.; Kirali, E.G.

2013-01-01

Bentonites are commonly used adsorbent on bleaching cotton oil to produce edible oil products. Bleaching capacities of neutralized cotton oil were investigated with acid-activated Arguvan and Kursunlu bentonites. Two models for acid activation of the bentonites were developed by using a full factorial experimental design and central composite design. The parameters used to develop these models were contact time, solid to liquid ratio, acid concentration and moisture of bentonite. By using a constrained optimization program, the maximum bleaching capacities of neutralized cotton oil were determined as 99.99% and 48.5% for Arguvan and Kursunlu, respectively. Optimum results showed that Turkish bentonites (especially Arguvan bentonite) have high bleaching ability and they can be used efficiently to bleach neutralized cotton oil by considering the favorable volume weight, capacity of oil adsorbed and filtration rate. (author)

Effect of Grafting Method, Graft Cover and Foliar Spray of some Mineral Elements on Persian Walnut Graft-take and Winter Survival Rate

Directory of Open Access Journals (Sweden)

Reza Rezaee

2017-09-01

Full Text Available Introduction: Persian walnut (Juglans regia L. is an important nut crop in Iran and many parts of the world. One of the major challenges of growing walnut is planting of non-grafted walnut trees in orchards, which leads to the reduction of yield, quality and productivity of walnut orchards. Compared to the other fruit trees, walnut grafting is difficult and even newly grafted walnut seedlings are vulnerable to fall or winter frost chilling, so that most of the seedlings are lost after subjecting to the cold winter. There are a few studies reporting successful grafting in outdoor conditions, however, final grafting take after winter has been usually ignored. Hence, increased walnut grafting success and improved tree growth after grafting through foliar nutrient application may lead to increased tolerance of chilling. Therefore, main goals of this research were to investigate the effect of some graft covers and role of foliar spray of calcium, boron and zinc on the reduction of frost damage in newly grafted seedlings under outdoor conditions. Materials and methods: This research was conducted at agricultural research station, Khoy city, west Azerbaijan province, during 2012-2014. In the first experiment, three methods of grafting including cleft, bark and V-shaped, and two kinds of graft covers including moist sawdust and superabsorbent plus cotton wool were investigated in terms of grafting success and quality of seedlings. In the second experiment, effect of the three above-mentioned grafting methods and two levels of foliar spray including sequential spray of Ca (4 ppm, B and Zn (2% (3 times during growth season and control (no spray were studied in terms of frost damage. The experiments conducted in factorial based on randomized complete block design with 10 trees in each plot. Data were collected 45 days after grafting take, final grafting take after one winter, subsequent scion growth length and diameter and concentration of Ca, B and Zn in

Hydrophilic/hydrophobic character of grafted cellulose

Energy Technology Data Exchange (ETDEWEB)

Takacs, E., E-mail: takacs@iki.kfki.h [Institute of Isotopes, Hungarian Academy of Sciences, Budapest (Hungary); Wojnarovits, L. [Institute of Isotopes, Hungarian Academy of Sciences, Budapest (Hungary); Borsa, J. [Budapest University of Technology and Economics (Hungary); Racz, I. [Bay Zoltan Institute for Materials Science and Technology, Budapest (Hungary)

2010-04-15

Vinyl monomers with long paraffin chains were grafted onto two kinds of cellulose (cotton and cotton linter) by direct irradiation grafting technique. The effect of dose, monomer structure and concentration, as well as homopolymer suppressor (styrene) concentration on the grafting yield was studied and the optimal grafting conditions were established. Grafting decreased the swelling of the samples in water and increased their polymer compatibility in polypropylene matrix.

Synthesis, characterization and dyeing assessment of novel acid azo dyes and mordent acid azo dyes based on 2-hydroxy-4-methoxybenzophenone on wool and silk fabrics

Directory of Open Access Journals (Sweden)

DHIRUBHAI J. DESAI

2010-05-01

Full Text Available Novel acid mono azo and mordent acid mono azo dyes were synthesised by the coupling of diazonium salt solution of different aromatic amines with 2-hydroxy-4-methoxybenzophenone. The resulting dyes were characterized by spectral techniques, i.e., elemental analysis, IR, 1H-NMR and UV–visible spectroscopy. The dyeing performance of all the dyes was evaluated on wool and silk fabrics. The dyeing of chrome pre-treated wool and silk fabrics showed better hues on mordented fabrics. Dyeing of wool and silk fabrics resulted in pinkish blue to red shades with very good depth and levelness. The dyed fabrics showed excellent to very good light, washing, perspiration, sublimation and rubbing fastness. The results of antibacterial studies of chrome pre-treated fabrics revealed that the toxicity of mordented dyes against Escherichia coli, Staphylococcus aureus, Salmonella typhi, Bacillus subtilis bacteria was fairly good.

Fabrication of thermo-responsive cotton fabrics using poly(vinyl caprolactam-co-hydroxyethyl acrylamide) copolymer.

Science.gov (United States)

Xiao, Min; González, Edurne; Monterroza, Alexis Martell; Frey, Margaret

2017-10-15

A thermo-responsive polymer with hydrophilic to hydrophobic transition behavior, poly(vinyl caprolactam-co-hydroxyethyl acrylamide) P(VCL-co-HEAA), was prepared by copolymerization of vinyl caprolactam and N-hydroxyethyl acrylamide via free radical solution polymerization. The resulting copolymer was characterized by Fourier transform infrared spectroscopy (FTIR), 1 H nuclear magnetic resonance (NMR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The lower critical solution temperature (LCST) of P(VCL-co-HEAA) was determined at 34.5°C. This thermo-responsive polymer was then grafted onto cotton fabrics using 1,2,3,4-butanetetracarboxylic acid (BTCA) as crosslinker and sodium hypophosphite (SHP) as catalyst. FTIR and energy dispersive X-ray spectroscopy (EDS) studies confirmed the successful grafting reaction. The modified cotton fabric exhibited thermo-responsive behavior as evidenced by water vapor permeability measurement confirming decreased permeability at elevated temperature. This is the first demonstration that a PVCL based copolymer is grafted to cotton fabrics. This study provides a new thermo-responsive polymer for fabrication of smart cotton fabrics with thermally switchable hydrophilicity. Copyright © 2017 Elsevier Ltd. All rights reserved.

Plasma treatments of wool fiber surface for microfluidic applications

Energy Technology Data Exchange (ETDEWEB)

Jeon, So-Hyoun; Hwang, Ki-Hwan; Lee, Jin Su [Department of Chemistry, Sungkyunkwan University, 440-746 Suwon (Korea, Republic of); Boo, Jin-Hyo, E-mail: jhboo@skku.edu [Department of Chemistry, Sungkyunkwan University, 440-746 Suwon (Korea, Republic of); Yun, Sang H., E-mail: shy@kth.se [Institute of Basic Science, Sungkyunkwan University, 440-746 Suwon (Korea, Republic of)

2015-09-15

Highlights: • We used atmospheric plasma for tuning the wettability of wool fibers. • The wicking rates of the wool fibers increased with increasing treatment time. • The increasing of wettability results in removement of fatty acid on the wool surface. - Abstract: Recent progress in health diagnostics has led to the development of simple and inexpensive systems. Thread-based microfluidic devices allow for portable and inexpensive field-based technologies enabling medical diagnostics, environmental monitoring, and food safety analysis. However, controlling the flow rate of wool thread, which is a very important part of thread-based microfluidic devices, is quite difficult. For this reason, we focused on thread-based microfluidics in the study. We developed a method of changing the wettability of hydrophobic thread, including wool thread. Thus, using natural wool thread as a channel, we demonstrate herein that the manipulation of the liquid flow, such as micro selecting and micro mixing, can be achieved by applying plasma treatment to wool thread. In addition to enabling the flow control of the treated wool channels consisting of all natural substances, this procedure will also be beneficial for biological sensing devices. We found that wools treated with various gases have different flow rates. We used an atmospheric plasma with O{sub 2}, N{sub 2} and Ar gases.

Development of Highly Efficient Grafting Technique and Synthesis of Natural Polymer-Based Graft Adsorbent

Energy Technology Data Exchange (ETDEWEB)

Ueki, Y; Seko, N; Tamada, M [Japan Atomic Energy Agency, Quantum Beam Science Directorate, Takasaki (Japan)

2012-09-15

In the framework of the CRP, Japan has focused on the development of fibrous adsorbents for removal of toxic metal ions and recovery of significant metal ions from industrial wastewater and streaming water. Graft polymerization was carried out by using gamma irradiation facility and electron beam accelerator. Emulsion grafting is a novel topic for synthesis of metal ion adsorbents which are prepared from fibrous trunk polymers such as polyethylene fibre and biodegradable nonwoven fabrics. The emulsion grafting, where monomer micelles are dispersed in water in the presence of surfactant, is a highly efficient and economic grafting technique as compared to general organic solvent system. The resultant cotton-based adsorbent has high adsorption efficiency and high adsorption capacity for Hg, besides, it is biodegradable. Polylactic acid can also be used as a trunk material for the grafting. (author)

Acrylique acid grafted polyolefines. Thermoadhesive applications

International Nuclear Information System (INIS)

Guimon, Claude

1979-01-01

Radiochemical grafting of polyolefines by peroxidation has been industrialized in France for about 10 years by irradiation of these polymers with an electron accelerator and then treated by acrylic acid. Products obtained show a high adhesivity on metallic surfaces above their melting point. The main application of acrylic acid grafted high density polyethylene is composite film with aluminum foil for thermosealing of plastic bottle caps of sterilized milk. Acrylic acid grafted polypropylene is used in suspension in a volatile liquid for aluminum foil coating satisfying food packaging regulations [fr

Effect of acid additives on graft copolymerization and water absorption of graft copolymers of cassava starch and acrylamide/acrylic acid

International Nuclear Information System (INIS)

Kiatkamjornwong, Suda; Mongkolsawat, Kanlaya; Sonsuk, Manit

2003-01-01

Gelatinized cassava starch was radiation graft copolymerized with acrylamide or acrylic acid in the presence of sulfuric acid, nitric acid or maleic acid at a specific dose rate to a fixed total dose. Homopolymer or free copolymer was extracted by water to obtain the pure graft copolymer, which was subsequently saponified with 5% potassium hydroxide solution at room temperature for 90 min. The saponified graft copolymer was investigated for the effect of acid additives and water absorption. The addition of 2% maleic acid into the grafting reaction containing acrylamide-to-starch ratio of 2.5:1 can produce the superabsorbent copolymer having water absorption as high as 2,256 ± 25 g g -1 . The effect of acid additive was explained. (author)

Humidity Induces Changes in the Dimensions of Hydrogel-Coated Wool Yarns

Directory of Open Access Journals (Sweden)

Lanlan Wang

2018-03-01

Full Text Available Polymeric hydrogel based on acrylic acid (AA and N,N-dimethylacrylamide (DMAA was prepared by photopolymerization reaction, using nano-alumina as the inorganic crosslinker. Hydrogel-coated wool yarns determine their dimensional changes under humidity conditions. Surface morphology of the hydrogel-coated wool yarns was carried out using SEM microscopy. The hydrogel was further characterized by Fourier transformer infrared spectrum (FTIR, gel permeation chromatography (GPC, differential scanning calorimetry (DSC, thermogravimetry (TG and differential thermogravimetry (DTG. This contribution showed that UV-initiated polymerization coating wool yarns can change the functional properties of wool fibers.

Mechanism of phytohormone involvement in feedback regulation of cotton leaf senescence induced by potassium deficiency.

Science.gov (United States)

Wang, Ye; Li, Bo; Du, Mingwei; Eneji, A Egrinya; Wang, Baomin; Duan, Liusheng; Li, Zhaohu; Tian, Xiaoli

2012-10-01

To elucidate the phytohormonal basis of the feedback regulation of leaf senescence induced by potassium (K) deficiency in cotton (Gossypium hirsutum L.), two cultivars contrasting in sensitivity to K deficiency were self- and reciprocally grafted hypocotyl-to-hypocotyl, using standard grafting (one scion grafted onto one rootstock), Y grafting (two scions grafted onto one rootstock), and inverted Y grafting (one scion grafted onto two rootstocks) at the seedling stage. K deficiency (0.03mM for standard and Y grafting, and 0.01mM for inverted Y grafting) increased the root abscisic acid (ABA) concentration by 1.6- to 3.1-fold and xylem ABA delivery rates by 1.8- to 4.6-fold. The K deficiency also decreased the delivery rates of xylem cytokinins [CKs; including the zeatin riboside (ZR) and isopentenyl adenosine (iPA) type] by 29-65% and leaf CK concentration by 16-57%. The leaf ABA concentration and xylem ABA deliveries were consistently greater in CCRI41 (more sensitive to K deficiency) than in SCRC22 (less sensitive to K deficiency) scions under K deficiency, and ZR- and iPA-type levels were consistently lower in the former than in the latter, irrespective of rootstock cultivar or grafting type, indicating that cotton shoot influences the levels of ABA and CKs in leaves and xylem sap. Because the scions had little influence on phytohormone levels in the roots (rootstocks) of all three types of grafts and rootstock xylem sap (collected below the graft union) of Y and inverted Y grafts, it appears that the site for basipetal feedback signal(s) involved in the regulation of xylem phytohormones is the hypocotyl of cotton seedlings. Also, the target of this feedback signal(s) is more likely to be the changes in xylem phytohormones within tissues of the hypocotyl rather than the export of phytohormones from the roots.

The radiation grafting of vinyl monomers to cotton fabrics

International Nuclear Information System (INIS)

Shiraishi, N.; Williams, J.L.; Stannett, V.

1982-01-01

Cobalt 60 γ and electron beam radiation were used to graft diethylphosphatoethyl methacrylate, pure and in 90:10 methanol solution, to cotton cloth. This monomer, with an 11.64% phosphorus content, was especially developed by the Scott Paper Co. to develop fire retardancy. A simple pad and squeeze application followed by direct irradiation under a nitrogen atmosphere was used. Although excess monomer could be removed by washing with water, no solvent for the polymer was found so only the total 'add-ons' could be measured. With 60 Co irradiation, total polymerization was obtained with more than 1 Mrad but with electron beam irradiation only about 50% conversion was obtained even with 10 Mrad. No acceleration in the rates could be achieved with the viscous pure monomer as opposed to in solution. Yields adequate to impart reasonable fire retardancy could, however, be obtained with about 3 Mrad with electrons. No noticeable degradation of the polymer occurred at the doses used. (author)

STIFFNESS MODIFICATION OF COTTON IN CHITOSAN TREATMENT

Directory of Open Access Journals (Sweden)

CAMPOS Juan

2017-05-01

Full Text Available Chitosan is a biopolymer obtained from chitin, and among their most important aspects highlights its applications in a lot of industrial sectors due to its intrinsic properties, especially in the textile sector. In the last years, chitosan is widely used in the cotton and wool finishing processes due to its bond between them and its properties as an antifungical and antimicrobial properties. In this paper three different molecular weight chitosan are used in the finishing process of cotton to evaluate its influence in the surface properties modification. In order to evaluate the effect of the treatment with chitosan, flexural stiffness test is performed in warp and weft direction, and then the total value is calculated. The cotton fabric is treated with 5 g/L of different types of chitosan in an impregnation bath. This study shows the extent of surface properties modification of the cotton provided by three types of chitosan treatment. The results show that all types of chitosan modify the cotton flexural rigidity properties but the one which modifies it in a relevant manner is chitosan originated from shrimps. Chitosan, textile, flexural stiffnes, chitin, cotton.

Grafted Cellulose Based Adsorbents for Selective Separation Purposes

Energy Technology Data Exchange (ETDEWEB)

Takacs, E; Wojnarovits, L [Institute of Isotopes, Hungarian Academy of Sciences, Budapest (Hungary)

2012-09-15

The effect of high energy ionizing radiation on cotton-cellulose was studied. It was found that degradation of cellulose started at low doses, below 5 kGy, resulting in decrease in the degree of polymerization. However, the mechanical properties of cotton-cellulose samples only slightly changed with the dose up to 40 kGy. Acrylate type monomers were successfully grafted to cellulose by mutual and by pre-irradiation grafting technique. With both techniques the grafting yield increased with increasing dose and monomer concentration. In the case of pre-irradiation grafting the increase in grafting time also resulted in an increase in grafting percentage. Cotton-cellulose was functionalized using pre-irradiation grafting (PIG) and simultaneous grafting (SG) of glycidyl methacrylate (GMA). The adsorption properties of this material were further enhanced by {beta}-cyclodextrin (CD) immobilization. This molecule is known for its unique ability to form inclusion complexes among others with aromatic compounds like phenols, pesticide, dyes, etc. (author)

Synthesis of Radiation Grafted Polymer Matrices for Separation and Industrial Applications

Energy Technology Data Exchange (ETDEWEB)

Bhardwaj, Y K; Virendra, K; Goel, N K; Sarma, K S.S.; Sabharwal, S [Radiation Technology Development Division, Bhabha Atomic Research Centre, Trombay, Mumbai-400 085 (India)

2012-09-15

Grafting of acrylonitrile onto non-woven porous polypropylene fibre sheet using electron beam was carried out by post-irradiation grafting. Grafting extent of {approx}125% was achieved. The grafted nitrile groups were amidoximated and studied for uranium uptake from sea water and heavy metal ions (Co{sup 2+}, Ni{sup 2+}, Mn{sup 2+}, and Cd{sup 2+}) from aqueous solutions. Adsorption and elution of adsorbed ions in suitable eluents was studied. The grafting process was upgraded to pilot scale to obtain 1x1 m{sup 2} sheets. Mutual radiation grafting technique was used for grafting of vinylbenzyltrimethyl ammonium chloride, [2- (methacryloyloxy)ethyl] trimethylammonium chloride and [2-(acryloyloxyethyl)]trimethylammonium chloride onto cotton cellulose substrate. The grafted matrices showed significantly higher water uptake and good water retention properties. The antibacterial efficacy of the grafted products was found to be a function of extent of grafting and the type of bacteria (Escherichia coli, Pseudomonas flourescens, Staphylococcus aureus and Bacillus cereus). PVBT-g-cotton was studied for its protein adsorption behaviour in continuous column process using Bovine serum albumin (BSA) as a model protein. Mutual radiation grafting technique was used to graft acrylic acid on micrometer thick micro-porous polypropylene membrane. Contact angle measurement studies showed that initial grafting as well as radiation treatment of poly(propylene) in aqueous medium and in presence of Mohr's salt enhances its affinity towards the grafting solution. The enhancement in the polar component of surface energy of treated polypropylene membrane is the primary cause of grafting enhancement. The membranes grafted to an extent of {approx}20% were found to perform comparably with the battery separator presently being used by battery industry. Acrylic acid was grafted to Teflon scrap by mutual radiation grafting technique. The grafting extent decreased with increasing dose rate and

Genetic correlations between wool traits and meat quality traits in Merino sheep.

Science.gov (United States)

Mortimer, S I; Hatcher, S; Fogarty, N M; van der Werf, J H J; Brown, D J; Swan, A A; Jacob, R H; Geesink, G H; Hopkins, D L; Edwards, J E Hocking; Ponnampalam, E N; Warner, R D; Pearce, K L; Pethick, D W

2017-10-01

Genetic correlations between 29 wool production and quality traits and 25 meat quality and nutritional value traits were estimated for Merino sheep from an Information Nucleus (IN). Genetic correlations among the meat quality and nutritional value traits are also reported. The IN comprised 8 flocks linked genetically and managed across a range of sheep production environments in Australia. The wool traits included over 5,000 yearling and 3,700 adult records for fleece weight, fiber diameter, staple length, staple strength, fiber diameter variation, scoured wool color, and visual scores for breech and body wrinkle. The meat quality traits were measured on samples from the and included over 1,200 records from progeny of over 170 sires for intramuscular fat (IMF), shear force of meat aged for 5 d (SF5), 24 h postmortem pH (pHLL; also measured in the , pHST), fresh and retail meat color and meat nutritional value traits such as iron and zinc levels, and long-chain omega-3 and omega-6 polyunsaturated fatty acid levels. Estimated heritabilities for IMF, SF5, pHLL, pHST, retail meat color lightness (), myoglobin, iron, zinc and across the range of long-chain fatty acids were 0.58 ± 0.11, 0.10 ± 0.09, 0.15 ± 0.07, 0.20 ± 0.10, 0.59 ± 0.15, 0.31 ± 0.09, 0.20 ± 0.09, 0.11 ± 0.09, and range of 0.00 (eicosapentaenoic, docosapentaenoic, and arachidonic acids) to 0.14 ± 0.07 (linoleic acid), respectively. The genetic correlations between the wool production and meat quality traits were low to negligible and indicate that wool breeding programs will have little or no effect on meat quality. There were moderately favorable genetic correlations between important yearling wool production traits and the omega-3 fatty acids that were reduced for corresponding adult wool production traits, but these correlations are unlikely to be important in wool/meat breeding programs because they have high SE, and the omega-3 traits have little or no genetic variance. Significant genetic

Effect of Polylactic Acid-Degradable Film Mulch on Soil Temperature and Cotton Yield

Directory of Open Access Journals (Sweden)

ZHANG Ni

2016-03-01

Full Text Available Concern on biodegradable plastic film is increasing because of pollution problems caused by the plastic films currently used. The objective of this field experiment is to evaluate the effect of two thicknesses of polyactic acid-degradable film on soil temperature and cotton yield. The results showed that small holes appeared in the polyactic acid-degradable film at 17~22 d after it was installed. Burst period appeared about 60 d after installation. Splits were observed in the polyactic acid-degradable film at 130 d after installation. Soil temperatures rose slowly under polyactic acid-degradable film during the cotton seedling stage. Daytime soil temperatures were 0.8℃ and 6.2℃ lower under 18μm and 15μm thick polyactic acid-degradable film than non-degradable plastic film(CK, respectively. Nighttime soil temperatures under the polyactic acid-degradable film were about 1℃ warmer than CK. There was no significant difference in cotton yields between the 18μm polyactic acid degradable film treatment and CK. In contrast, yields in the 15μm degradable plastic film treatment were 8.9% less than that in CK. This study indicated that 18μm polyactic acid degradable plastic film had good degradability and no negative effect on cotton growth. The 18μm polyactic acid degradable plastic film can replace ordinary plastic film in agricultural production.

In vitro release of arachidonic acid and in vivo responses to respirable fractions of cotton dust

International Nuclear Information System (INIS)

Thomson, T.A.; Edwards, J.H.; Al-Zubaidy, T.S.; Brown, R.C.; Poole, A.; Nicholls, P.J.

1986-01-01

It was considered that the fall in lung function seen after exposure to cotton dust may be attributable in part to the activity of arachidonic acid metabolites, such as leucotrienes as well as to the more established release of histamine by cotton dust. However, we found that cotton and barley dusts elicited poor release of arachidonic acid from an established macrophage like cell line compared with that observed with other organic dusts. In the experimental animal, pulmonary cellular responses to both cotton and barley dust were similar to those evoked by moldy hay and pigeon dropping dusts, although after multiple doses a more severe response was seen to cotton and barley. Since both moldy hay and pigeon droppings elicit a greater arachidonic acid release than cotton or barley, a role for arachidonic acid in inducing the cellular response is less likely than other factors. There are limitations to our conclusions using this system, i.e., the arachidonic acid may be released in a nonmetabolized form, although it is noted that the two dusts with the greatest arachidonic acid release produce their clinical responses in humans largely by hypersensitivity mechanisms

Studies on Synthesis and Dyeing Preformance of Acid Dyes Based on 4,7-Dihydroxy-1,10-Phenanthroline-2,9-Dione

Directory of Open Access Journals (Sweden)

B. V. Patel

2008-01-01

Full Text Available Some new azo acid dyes were prepared by coupling various diazotized acid components such as anthranilic acid, sulphanilic acid, laurent acid, peri acid, tobias acid, H-acid, J-acid, gamma acid, sulphotobias acid, 4-aminotoluiene-3-sulphonic acid, 5-sulpho- anthranilic acid, 2-naphthylamine-3,6,8-trisulphonic acid, bronner acid, metanilic acid and cleve acid with 4,7-dihydroxy-1,10-phenanthroline-2,9-dione. The dyes were characterized by elemental, IR and TLC analyses. Their dyeing performance as acid dyes has been assessed on viscose rayon, wool and cotton fibres.

Time-Dependent Variations in Structure of Sheep Wool Irradiated by Electron Beam

Directory of Open Access Journals (Sweden)

Zuzana Hanzlíková

2017-01-01

Full Text Available Wool scoured in tap water with no special degreasing and containing a balanced humidity responding to usual laboratory conditions was irradiated by accelerated electron beam in the range of 0–350 kGy dose. Time variations of the wool structure were measured using FTIR, Raman, and EPR spectroscopy. The aim was to determine whether preexposure treatment of the wool, as well as postexposure time, affects the properties of the irradiated wool. Reactive products such as S-sulfonate, cystine monoxide, cystine dioxide, cysteic acid, disulphides, and carboxylates displayed a considerable fluctuation in quantity depending on both the absorbed dose and time. Mutual transformations of S-oxidized products into cysteic acid appeared to be faster than those in dry and degreased wool assuming that the present humidity inside the fibres is decisive as an oxygen source. EPR results indicated a longer lifetime for free radicals induced by lower doses compared with the radicals generated by higher ones. The pattern of the conformational composition of the secondary structure (α-helix, β-sheet, random, and residual conformations also showed a large variability depending on absorbed dose as well as postexposure time. The most stable secondary structure was observed in nonirradiated wool but even this showed a small but observable change after a longer time, too.

Amino acids grafting of Ar+ ions modified PE

International Nuclear Information System (INIS)

Svorcik, V.; Hnatowicz, V.; Stopka, P.; Bacakova, L.; Heitz, J.; Oechsner, R.; Ryssel, H.

2001-01-01

Polyethylene (PE) was irradiated with 63 keV Ar + ions to the fluences from 1x10 12 to 3x10 15 cm -2 and then grafted at room temperature from water solution with amino acids (alanine, leucine). Using various spectroscopic techniques (UV-VIS, FTIR, RBS and EPR) it was shown that the amino acids penetrate into PE where they are eventually captured either on double bonds or on free radicals created by the ion irradiation. Grafting with amino acids in the whole specimen layer modified by irradiation is observed. The ion-beam-modified and amino-acid grafted PE is supposed to exhibit increased biocompatibility. (author)

Radiation flame proofing of polyester/cotton blends

International Nuclear Information System (INIS)

Liepins, R.; Surles, J.R.; Morosoff, N.; Stannett, V.T.; Barker, R.H.

1977-01-01

Methodology has been developed for the grafting of vinyl functional organobromide and organophosphorus compounds on polyester fibers and 50/50 PET/cotton fabric. Procedures were developed for localized grafting of vinyl bromide (VBr) and diethylvinylphosphonate (DEVP) upon PET fibers. Oxygen index was used to evaluate the effect of the location of VBr and DEVP within the filament upon their flame retardance efficiencies. For the various bromine homopolymer grafts the apparent thermal stability of the graft and its flame retardance efficiency may be related to the alpha aliphatic hydrogen to bromine ratio. Using results from the polyester studies, techniques were devised for the treatment of 50/50 polyester/ cotton fabrics. Both homopolymer and copolymer grafts were evaluated but the greatest degree of success was attained using mixtures of phosphorus and bromine containing monomers. The results of these studies will be reviewed and their implications for development as commercial textile treatments discussed. (author)

Direct catalytic production of sorbitol from waste cellulosic materials.

Science.gov (United States)

Ribeiro, Lucília Sousa; Órfão, José J de Melo; Pereira, Manuel Fernando Ribeiro

2017-05-01

Cotton wool, cotton textile, tissue paper and printing paper, all potential waste cellulosic materials, were directly converted to sorbitol using a Ru/CNT catalyst in the presence of H 2 and using only water as solvent, without any acids. Conversions up to 38% were attained for the raw substrates, with sorbitol yields below 10%. Ball-milling of the materials disrupted their crystallinity, allowing reaching 100% conversion of cotton wool, cotton textile and tissue paper after 4h, with sorbitol yields around 50%. Mix-milling these materials with the catalyst greatly enhanced their conversion rate, and the materials were efficiently converted to sorbitol with a yield around 50% in 2h. However, ball- and mix-milled printing paper presented a conversion of only 50% after 5h, with sorbitol yields of 7%. Amounts of sorbitol of 0.525, 0.511 and 0.559g could be obtained from 1g of cotton wool, cotton textile and tissue paper, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cotton fibers encapsulated with homo- and block copolymers: synthesis by the atom transfer radical polymerization grafting-from technique and solid-state NMR dynamic investigations.

Science.gov (United States)

Castelvetro, Valter; Geppi, Marco; Giaiacopi, Simone; Mollica, Giulia

2007-02-01

Cotton fibers were modified by surface-initiated atom transfer radical polymerization of ethyl acrylate (EA) followed by copolymerization with styrene. Either ethyl 2-bromopropionate as a sacrificial free initiator or Cu(II) as a deactivator was used to optimize the EA grafting yield and to preserve the livingness of the chain ends for the subsequent growth of a poly(styrene) (PSty) block from the poly(ethyl acrylate) (PEA) grafts. The polymer-encapsulated cotton fibers were analyzed by Fourier transform infrared spectroscopy, scanning electron microscopy, differential scanning calorimetry (DSC), thermogravimetric analysis, and solid-state NMR (high-resolution 13C cross-polarization magic angle spinning, 1H spin-lattice relaxation times, and 1H free induction decay analysis NMR). The latter allowed the detection of the dynamic modifications associated with the presence of homo- and block copolymer grafts. In particular, the results of the DSC and NMR investigations suggest a heterogeneous morphology of the g-PEA-b-PSty grafted skin, which could be described as an inner layer of g-PEA sandwiched between the semicrystalline cellulose of the core fiber and the high glass transition temperature PSty of the covalently linked outer layer. Such morphology results in a reduced molecular mobility of the PEA chains.

Graft polymerization of acrylic acid and methacrylic acid onto poly(vinylidene fluoride) powder in presence of metallic salt and sulfuric acid

Science.gov (United States)

Deng, Bo; Yu, Yang; Zhang, Bowu; Yang, Xuanxuan; Li, Linfan; Yu, Ming; Li, Jingye

2011-02-01

Poly(vinylidene fluoride) (PVDF) powder was grafted with acrylic acid (AAc) or methacrylic acid (MAA) by the pre-irradiation induced graft polymerization technique. The presence of graft chains was proven by FT-IR spectroscopy. The degree of grafting (DG) was calculated by the acid-base back titration method. The synergistic effect of acid and Mohr's salt on the grafting kinetics was examined. The results indicated that adding sulfuric acid and Mohr's salt simultaneously in AAc or MAA solutions led to a strong enhancement in the degree of grafting. The grafted PVDF powder was cast into microfiltration (MF) membranes using the phase inversion method and some properties of the obtained MF membranes were characterized.

Graft polymerization of acrylic acid and methacrylic acid onto poly(vinylidene fluoride) powder in presence of metallic salt and sulfuric acid

Energy Technology Data Exchange (ETDEWEB)

Deng Bo [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, No. 2019, Jialuo Road, Jiading Dist., 201800 Shanghai (China); Yu Yang; Zhang Bowu; Yang Xuanxuan [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, No. 2019, Jialuo Road, Jiading Dist., 201800 Shanghai (China); Graduate University of Chinese Academy of Sciences, No. 19, Yuquan Road, Shijingshan Dist., 100049 Beijing (China); Li Linfan; Yu Ming [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, No. 2019, Jialuo Road, Jiading Dist., 201800 Shanghai (China); Li Jingye, E-mail: jingyeli@sinap.ac.c [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, No. 2019, Jialuo Road, Jiading Dist., 201800 Shanghai (China)

2011-02-15

Poly(vinylidene fluoride) (PVDF) powder was grafted with acrylic acid (AAc) or methacrylic acid (MAA) by the pre-irradiation induced graft polymerization technique. The presence of graft chains was proven by FT-IR spectroscopy. The degree of grafting (DG) was calculated by the acid-base back titration method. The synergistic effect of acid and Mohr's salt on the grafting kinetics was examined. The results indicated that adding sulfuric acid and Mohr's salt simultaneously in AAc or MAA solutions led to a strong enhancement in the degree of grafting. The grafted PVDF powder was cast into microfiltration (MF) membranes using the phase inversion method and some properties of the obtained MF membranes were characterized.

Graft polymerization of acrylic acid and methacrylic acid onto poly(vinylidene fluoride) powder in presence of metallic salt and sulfuric acid

International Nuclear Information System (INIS)

Deng Bo; Yu Yang; Zhang Bowu; Yang Xuanxuan; Li Linfan; Yu Ming; Li Jingye

2011-01-01

Poly(vinylidene fluoride) (PVDF) powder was grafted with acrylic acid (AAc) or methacrylic acid (MAA) by the pre-irradiation induced graft polymerization technique. The presence of graft chains was proven by FT-IR spectroscopy. The degree of grafting (DG) was calculated by the acid-base back titration method. The synergistic effect of acid and Mohr's salt on the grafting kinetics was examined. The results indicated that adding sulfuric acid and Mohr's salt simultaneously in AAc or MAA solutions led to a strong enhancement in the degree of grafting. The grafted PVDF powder was cast into microfiltration (MF) membranes using the phase inversion method and some properties of the obtained MF membranes were characterized.

Radiation-induced grafting of acrylic acid onto polypropylene film and its biodegradability

Science.gov (United States)

Mandal, Dev K.; Bhunia, Haripada; Bajpai, Pramod K.; Chaudhari, C. V.; Dubey, K. A.; Varshney, L.

2016-06-01

Polypropylene based commodity polyolefins are widely used in packaging, manufacturing, electrical, pharmaceutical and other applications. The aim of the present work is to study the effect of grafting of acrylic acid on the biodegradability of acrylic acid grafted polypropylene. The effect of different conditions showed that grafting percentage increased with increase in monomer concentration, radiation dose and inhibitor concentration but decreased with increase in radiation dose rate. The maximum grafting of 159.4% could be achieved at optimum conditions. The structure of grafted polypropylene films at different degree of grafting was characterized by EDS, FTIR, TGA, DSC, SEM and XRD. EDS studies showed that the increase in acrylic acid grafting percentage increased the hydrophilicity of the grafted films. FTIR studies indicated the presence of acrylic acid on the surface of polypropylene film. TGA studies revealed that thermal stability decreased with increase in grafting percentage. DSC studies showed that melting temperature and crystallinity of the grafted polypropylene films lower than polypropylene film. SEM studies indicated that increase in acrylic acid grafting percentage increased the wrinkles in the grafted films. The maximum biodegradability could be achieved to 6.85% for 90.5% grafting. This suggested that microorganisms present in the compost could biodegrade acrylic acid grafted polypropylene.

77 FR 3223 - National Emissions Standards for Hazardous Air Pollutants: Mineral Wool Production and Wool...

Science.gov (United States)

2012-01-23

... Emission Standards for Hazardous Air Pollutants: Mineral Wool Production Risk and Technology Review..., Administrative practice and procedure, Air pollution control, Hazardous substances, Intergovernmental relations... National Emissions Standards for Hazardous Air Pollutants: Mineral Wool Production and Wool Fiberglass...

Investigation of Ageing Effects on Organic Binders used for Mineral Wool Products

DEFF Research Database (Denmark)

Zafar, Ashar

mainly due to hydrolyzation of urea containing groups. On the other hand, XPS and ToF-SIMS characterization of alkanol amine-acid anhydride binder coated mineral fibres consistently showed that the surface chemical composition of the organic components of these samples did not change appreciably during......Phenol-Urea-Formaldehyde (PUF) binder based mineral wool products’ mechanical properties have been observed to degrade during ageing at elevated temperatures and humidity, while mineral wool products based on a newly developed alkanol amine-acid anhydride binder exhibited better ageing properties...... for the same duration of ageing. The main purpose of the present work is to examine the chemical changes occurring in the phenol-urea-formaldehyde binder based mineral fibres due to ageing, which cause deterioration of the mechanical properties of mineral wool products. This has been done using surface...

Induced resistance by cresotic acid (3-hydroxy-4-methyl methylbenzoic acid) against wilt disease of melon and cotton

International Nuclear Information System (INIS)

Dong, H.; Li, Z.; Zhang, D.; Li, W.; Tang, W.

2004-01-01

Cresotic acid (3-hydroxy-4-methylbenzoic acid) was proved be active in controlling wilt diseases of melon and cotton plants grown in the house. Soil drench with 200-1000 ppm cresotic acid induced 62-77 %, 69-79 % and 50-60 % protection against Fusarium oxysporum f.sp melonis (FOM) in melon, Fusarium oxysporum f.sp vasinfectum (FOV) and Verticillium dahliae in cotton, respectively. Since no inhibitory effect of cresotic acid on mycelial growth of these three fungual pathogens was observed in vitro, it is suggested that control of these wilt diseases with cresotic acid resulted from induced resistance. Cresotic acid induced resistance in melon plants not only against race 0, race 1, race 2 and race 1,2, but also against a mixture of these four races of FOM, suggesting a non-race- specific resistance. Level of induced resistance by cresotic acid against FOM depended on inoculum pressure applied to melon plants. At 25 day after inoculation with FOM, percentage protection induced by cresotic acid under low inoculum pressure retained a level of 51 %, while under high inoculum pressure percentage protection decreased to only 10 %. High concentrations of cresotic acid significantly reduced plant growth. Reduction in fresh weight of melon (36-51%) and cotton (42-71%) was obtained with 500-1000 ppm cresotic acid, while only less than 8% reduction occurred with 100-200 ppm. (author)

Judging The Effectiveness Of Wool Combing By The Entropy Of The Images Of Wool Slivers

Science.gov (United States)

Rodrigues, F. Carvalho; Carvalho, Fernando D.; Peixoto, J. Pinto; Silva, M. Santos

1989-04-01

In general it can be said that the textile industry endeavours to render a bunch of fibers chaotically distributed in space into an ordered spatial distribution. This fact is independent of the nature the fibers, i.e., the aim of getting into higher order states in the spatial distribution of the fibers dictates different industrial processes depending on whether the fibers are wool, cotton or man made but the all effect is centred on obtaining at every step of any of the processes a more ordered state regarding the spatial distribution of the fibers. Thinking about the textile processes as a method of getting order out of chaos, the concept of entropy appears as the most appropriate judging parameter on the effectiveness of a step in the chain of an industrial process to produce a regular textile. In fact, entropy is the hidden parameter not only for the textile industry but also for the non woven and paper industrial processes. It happens that in these industries the state of order is linked with the spatial distribution of fibers and to obtain an image of a spatial distribution is an easy matter. To compute the image entropy from the grey level distribution requires only the use of the Shannon formula. In this paper to illustrate the usefulness of employing the entropy of an image concept to textiles the evolution of the entropy of wool slivers along the combing process is matched against the state of parallelization of the fibbers along the seven steps as measured by the existing method. The advantages of the entropy method over the previous method based on diffraction is also demonstrated.

Adsorption of Cu(II), Hg(II), and Ni(II) ions by modified natural wool chelating fibers

International Nuclear Information System (INIS)

Monier, M.; Ayad, D.M.; Sarhan, A.A.

2010-01-01

The graft copolymerization of ethyl acrylate (EA) onto natural wool fibers initiated by potassium persulphate and Mohr's salt redox initiator system in limited aqueous medium was carried out in heterogeneous media. Ester groups of the grafted copolymers were partially converted into hydrazide function groups followed by hydrazone formation through reaction with isatin. Also the application of the modified fibers for metal ion uptake was studied using Cu(II), Hg(II) and Ni(II). The modified chelating fibers were characterized using FTIR spectroscopy, SEM and X-ray diffraction.

Heterogeneous in situ polymerization of polyaniline (PANI) nanofibers on cotton textiles: Improved electrical conductivity, electrical switching, and tuning properties.

Science.gov (United States)

Tissera, Nadeeka D; Wijesena, Ruchira N; Rathnayake, Samantha; de Silva, Rohini M; de Silva, K M Nalin

2018-04-15

Electrically conductive cotton fabric was fabricated by in situ one pot oxidative polymerization of aniline. Using a simple heterogeneous polymerization method, polyaniline (PANI) nano fibers with an average fiber diameter of 40-75 nm were grafted in situ onto cotton fabric. The electrical conductivity of the PANI nanofiber grafted fabric was improved 10 fold compared to fabric grafted with PANI nanoclusters having an average cluster size of 145-315 nm. The surface morphology of the cotton fibers was characterized using SEM and AFM. Electrical conductivity of PANI nanofibers on the cotton textile was further improved from 76 kΏ/cm to 1 kΏ/cm by increasing the HCl concentration from 1 M to 3 M in the polymerization medium. PANI grafted cotton fabrics were analyzed using FTIR, and the data showed the presence of polyaniline functional groups on the treated fabric. Further evidence was present for the chemical interaction of PANI with cellulose. Dopant level and morphology dependent electron transition behavior of PANI nanostructures grafted on cotton fabric was further characterized using UV-vis spectroscopy. The electrical conductivity of the PANI nano fiber grafted cotton fabric can be tuned by immersing the fabric in pH 2 and pH 6 solutions for multiple cycles. Copyright © 2018. Published by Elsevier Ltd.

Adsorption of Cu(II), Hg(II), and Ni(II) ions by modified natural wool chelating fibers

Energy Technology Data Exchange (ETDEWEB)

Monier, M., E-mail: monierchem@yahoo.com [Chemistry Department, Drexel University, Philadelphia, PA (United States); Chemistry Department, Faculty of Science, Mansoura University, Mansoura (Egypt); Ayad, D.M.; Sarhan, A.A. [Chemistry Department, Faculty of Science, Mansoura University, Mansoura (Egypt)

2010-04-15

The graft copolymerization of ethyl acrylate (EA) onto natural wool fibers initiated by potassium persulphate and Mohr's salt redox initiator system in limited aqueous medium was carried out in heterogeneous media. Ester groups of the grafted copolymers were partially converted into hydrazide function groups followed by hydrazone formation through reaction with isatin. Also the application of the modified fibers for metal ion uptake was studied using Cu(II), Hg(II) and Ni(II). The modified chelating fibers were characterized using FTIR spectroscopy, SEM and X-ray diffraction.

Adsorption of Cu(II), Hg(II), and Ni(II) ions by modified natural wool chelating fibers.

Science.gov (United States)

Monier, M; Ayad, D M; Sarhan, A A

2010-04-15

The graft copolymerization of ethyl acrylate (EA) onto natural wool fibers initiated by potassium persulphate and Mohr's salt redox initiator system in limited aqueous medium was carried out in heterogeneous media. Ester groups of the grafted copolymers were partially converted into hydrazide function groups followed by hydrazone formation through reaction with isatin. Also the application of the modified fibers for metal ion uptake was studied using Cu(II), Hg(II) and Ni(II). The modified chelating fibers were characterized using FTIR spectroscopy, SEM and X-ray diffraction. 2009 Elsevier B.V. All rights reserved.

Studies on Synthesis and Dyeing Preformance of Acid Dyes Based on 4,7-Dihydroxy-3,8-di-α-naphthylazo-1,10-phenanthroline-2,9-Dione

Directory of Open Access Journals (Sweden)

B. V. Patel

2007-01-01

Full Text Available Some new azo acid dyes were prepared by coupling various diazotized acid components such as anthranilic acid, sulphanilic acid, laurentacid, peri acid, tobias acid, H-acid, J-acid, gamma acid, sulphotobias acid,4-aminotoluiene-3-sulphonic acid, 5-sulpho- anthranilic acid, 2-naphthylamine-3,6,8-trisulphonic acid, bronner acid, metanilic acid and cleve acid with 4,7-dihydroxy-3,8-di-α-naphthylazo-1,10-phenanthroline-2,9-dione. The dyes were characterized by elemental, IR and TLC analyses. Their dyeing performance as acid dyes has been assessed on viscose rayon, wool and cotton fibres.

Some spectroscopic studies of cotton-G-styrene prepared by γ irradiation

International Nuclear Information System (INIS)

Dessouki, A.M.; Zahran, A.H.; Abo-Zeid, M.; Badr, Y.; Mousa, A.

1986-01-01

Absorption of water by graft copolymers obtained by direct radiation-induced grafting of styrene onto cotton fabrics has been studied. High-resolution nuclear magnetic resonance was used to study the nature of water absorption by these graft copolymers and its dependence on percent water content and degree of grafting percent. It was found that for cotton samples having increasing water content percent, first a rapid decrease in the width at half-value (upsilonsub(1/2)) corresponds to bound water strongly attached to the molecules of cellulose. On further increasing the water content percent, a small or zero change in upsilonsub(1/2) was observed corresponding to free water). Quantitative infrared measurements of the graft copolymers were carried out. The results showed the possibility of using an accurate IR technique for the quantitative estimation of the degree of grafting. This was achieved by carrying out a band shape analysis and correlating the changes in integral intensity and half-bandwidth with degree of grafting percent. (author

Radiation-induced grafting of acrylic acid onto polyethylene filaments

International Nuclear Information System (INIS)

Kaji, K.; Sakurada, I.; Okada, T.

1981-01-01

Radiation-induced grafting of acrylic acid onto high density polyethylene (PE) filaments was carried out in order to raise softening temperature and impart flame retardance and hydrophilic properties. Mutual γ-irradiation method was employed for the grafting in a mixture of acrylic acid (AA), ethylene dichloride and water containing a small amount of ferrous ammonium sulfate. The rate of grafting was very low at room temperature. On the other hand, large percent grafts were obtained when the grafting was performed at an elevated temperature. Activation energy for the initial rate of grafting was found to be 17 kcal/mol between 20 and 60 0 C and 10 kcal/ mol between 60 and 80 0 C. Original PE filament begins to shrink at 70 0 C, shows maximum shrinkage of 50% at 130 0 C and then breaks off at 136 0 C. When a 34% AA graft is converted to metallic salt the graft filament retains its filament form even above 300 0 C and gives maximum shrinkage of 15%. Burning tests by a wire-netting basket method indicate that graft filaments and their metallic salts do not form melting drops upon burning and are self-extinguishing. Original PE filament shows no moisture absorption; however, that of AA-grafted PE increases with increasing graft percent. (author)

Yields of cotton and other crops as affected by applications of sulfuric acid in irrigation water

Energy Technology Data Exchange (ETDEWEB)

Christensen, P.D.; Lyerly, P.J.

1954-01-01

Effects of sulfuric acid on crop yields and on some physical and chemical properties of a calcareous soil were investigated in a field experiment from 1947 through 1952. On cotton plots, the treatments consisted of applications of irrigation water containing no acid (pH 8.3), water acidified to pH 6, and water acidified to pH 2.3. Cotton was grown five seasons followed by sesbania the sixth season. A test on alfalfa was established using irrigation water not acidified and water acidifeid to pH 4. Alfalfa was grown for 3 years. The fourth year the alfalfa was plowed under and a crop of corn was raised. Cotton yields on the acid plots relative to the checks became progressively higher (with two exceptions) from one year to the next; however, in only one year (1950) were differences in yield statistically significant. With sesbania following cotton, highly significant yield increases resulted from the high acid treatment. Alfalfa yields on the acid plots became progressively greater relative to the non-acid plots, but yield differences were not significant. In cotton leaves, the acid treatments resulted in increased uptake of magnesium, sulfur, and phosphorus, but the increases were probably not significant. Uptake of sodium, potassium, calcium, manganese, and iron were not appreciably affected. In sesbania, the acid treatments did not significantly alter the uptake of any of the plant nutrients determined. There was some indication, however, that the uptake of sodium and iron was reduced by the acidification. The results of this study support the view that soil acidification on calcareous soils may improve the soil physical conditions and result in increased yields, particularly in some crops. The application of acid in the irrigation water did not prove to be economically feasible. 12 references, 1 figure, 7 tables.

In vitro Degradation of Butanediamine-Grafted Poly(DL-Lactic acids)

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

The degradation of butanediamine-grafted poly(DL-lactic acid) polymers (BDPLAs) in vitro together with PDLLA and maleic anhydride-grafted poly(DL-lactic acid) polymers (MPLAs) was investigated by observation of the changes of the pH value of incubation media, and weight loss ratio during degradation duration of 12 weeks. The results reveal that the acidity of PDLLA degradation products was weakened or neutralized by grafting butanediamine onto PDLLA. A uniform degradation of BDPLAs was observed in comparison with an acidity-induced auto-accelerating degradation featured by PDLLA and MPLAs. The biodegradation behaviors of BDPLAs can be adjusted by controlling the content of BDA. BDPLAs might be a new derivative of PDLLA-based biodegradable materials for medical applications without acidity-caused irritations and acidity-induced auto-accelerating degradation behavior as that of PDLLA.

Smart options for simultaneous functionalization and pigment coloration of cellulosic/wool blends.

Science.gov (United States)

Ibrahim, N A; Khalil, H M; El-Zairy, E M R; Abdalla, W A

2013-07-01

The present innovative research work deals with the individual use of chitosan (2.5 g/kg), Aloe vera (10 g/kg), triclosan (10 g/kg), TiO2-nanoparticles (TiO2-NP's, 10 g/kg), silicon micro-emulsion (20 g/kg) or a water/oil-repellent agent (40 g/kg) for modifying the pigment print paste to produce functionalized cotton/wool and viscose/wool pigment prints in one step process. The imparted functional properties such as antibacterial, antibacterial/UV-protection, soft-handle or water/oil-repellency together with the change in the printing properties were evaluated. Some of the obtained pigment prints were characterized by scanning electron microscope (SEM), and energy dispersive X-rays (EDX) to confirm deposition of certain functional additives on printed fabrics. The wide-range of imparted functional properties together with the depth of the obtained pigment prints were maintained over 80% even after 15 consecutive laundering cycles. The extent of retention in functional and pigment printing properties is influenced by the type of functional additive as well as the kind of substrate. Copyright © 2013 Elsevier Ltd. All rights reserved.

Radioinduced grafting of acrylic acid on expanded polystyrene matrices

International Nuclear Information System (INIS)

Postolache, C.; Simion, Corina; Dragomir, A.; Ponta, C.; Chirvasoiu, G.; Postolache, Carmen

1998-01-01

The unfixed surface radioactive contamination for low energy β radionuclides ( 3 H and 14 C) is determined by wiping the checked surfaces with sponge of absorbent materials. The activity built up by this sponge is measured by a liquid scintillator spectrometer. In this work, a method of obtaining sponges of expanded polystyrene with hydrophobic surface by radioinduced grafting of the acrylic acid is presented. These sponges have diameters of 28 mm, thicknesses of 1.5 - 2 mm and density of 22 mg/cm 3 . The samples were immersed in a grafting solution with the following composition: acrylic acid 30%, Cu SO 4 1%; water 69% which were deeply impregnated in repeated operations under vacuum and pressure conditions, respectively. Finally, the samples were exposed to γ radiation emitted by a 60 Co source (IETI 10 000 - IFIN-HH). The dose rates were 0.3, 0.5 and 1 Mrad/h. The range of the absorbed doses was 1 - 25 Mrad. The yields of radiochemical grafting have been determined by gravimetric, spectrophotometric and radiometric methods. The grafting agent used was 3 H labelled acrylic acid. The solvation capacity and the quenching characteristics of the grafted sponges in liquid scintillators, as well as the sampling yields have been analyzed as function of irradiation procedure and the percentage of grafted acrylic fragments. The superficial grafting of the acrylic acid has been carried out by the mentioned technique, leading to the increase of the wiping efficiency of the unfixed surface contaminating activity, without changes of polymer solubility in liquid scintillators and without the perturbation of the radioactivity detection process. (authors)

Sorption properties of wool

Directory of Open Access Journals (Sweden)

Radetić Maja M.

2004-01-01

Full Text Available Strict ecological legislation, especially in highly developed countries, imposed requirements for the purification of industrial effluents and the need for efficient oil clean up after sea and inland water spills. Although numerous processes have been developed, the application of sorbents is still one of the most efficient methods to remove heavy metal ions, dyes and crude oil from water. Recently, special attention was paid to sorbents based on natural fibres. A review of studies concerning the sorption properties of wool is presented in this paper. The presence of various functional groups on the wool fibre surface contributes to the efficient sorption of heavy metal ions and dyes. A hydrophobic, scaly surface and fibre crimp strongly influence the high sorption capacity of wool for oil. Wool has great sorption potential even as a recycled material. Accordingly, it can be used as a viable substitute to commercially available synthetic sorbents that show poor biodegradab ility.

Direct characterization of cotton fabrics treated with di-epoxide by nuclear magnetic resonance.

Science.gov (United States)

Xiao, Min; Chéry, Joronia; Keresztes, Ivan; Zax, David B; Frey, Margaret W

2017-10-15

A non-acid-based, di-functional epoxide, neopentyl glycol diglycidyl ether (NPGDGE), was used to modify cotton fabrics. Direct characterization of the modified cotton was conducted by Nuclear Magnetic Resonance (NMR) without grinding the fabric into a fine powder. NaOH and MgBr 2 were compared in catalyzing the reaction between the epoxide groups of NPGDGE and the hydroxyl groups of cellulose. Possible reaction routes were discussed. Scanning electron microscopy (SEM) images showed that while the MgBr 2 -catalyzed reaction resulted in self-polymerization of NPGDGE, the NaOH-catalyzed reaction did not. Fourier transform infrared spectroscopy (FTIR) showed that at high NaOH concentration cellulose restructures from allomorph I to II. NMR studies verified the incorporation of NPGDGE into cotton fabrics with a clear NMR signal, and confirmed that at higher NaOH concentration the efficiency of grafting of NPGDGE was increased. This demonstrates that use of solid state NMR directly on woven fabric samples can simultaneously characterize chemical modification and crystalline polymorph of cotton. No loss of tensile strength was observed for cotton fabrics modified with NPGDGE. Copyright © 2017 Elsevier Ltd. All rights reserved.

The International Sheep and Wool Handbook

Directory of Open Access Journals (Sweden)

Antonello Cannas

2011-02-01

Full Text Available This revised book is an expanded and updated version of the Australian Sheep and Wool Handbook published in 1991 and focuses on the sheep wool and meat industry. The book is divided in 5 sections, each including several chapters written by well-known and qualified researchers and industry representatives from many countries. The first section on Major sheep and wool industries, in my opinion, is particularly interesting because it explores the sheep and wool industries of leading countries (e.g. Australia, South Africa and New Zealand and continents (Europe and South America, and those of emerging countries (e.g. China.....

Dyeing and Adsorption Studies of Madder (Rubia tinctorum on Wool Fibers

Directory of Open Access Journals (Sweden)

Mahmoud FEIZ

2015-03-01

Full Text Available In this study, the dyeing behavior of wool fabrics with madder has been studied. Three well-known types of adsorption isotherms i.e. the Nernst, Freundlich and Langmuir isotherms were used to fit the data. It was found that the adsorption isotherm of madder on wool fibers follows Freundlich type of adsorption. The exponent α in Freundlich isotherm equation (Cf = k.Csα was obtained 0.61 corresponding to 0.5 for the direct dyes on cellulosic fibers. The effect of salt and pH on dyeing of wool samples was investigated by the use of color characteristics measurements. The results showed that addition of salt and acid (pH 4.5 to the dyebath resulted in an increase of adsorption. DOI: http://dx.doi.org/10.5755/j01.ms.21.1.5150

Hydrophobic cotton textile surfaces using an amphiphilic graphene oxide (GO) coating

International Nuclear Information System (INIS)

Tissera, Nadeeka D.; Wijesena, Ruchira N.; Perera, J. Rangana; Nalin de Silva, K.M.; Amaratunge, Gehan A.J.

2015-01-01

Graphical abstract: - Highlights: • Different GO dispersions were prepared by sonicating different amounts of GO in water. Degree of exfoliation of these GO sheets in water was analyzed using Atomic Force Microscopy (AFM). • AFM results obtained showed higher the GO concentration on water more the size of GO sheets and lesser the degree of exfoliation. • GO with different amounts was deposited on cotton fabric using simple dyeing method. • High GO loading on cotton increase the surface area coverage of the textile fibers with GO sheets. This led to less edge to mid area ratio of grafted GO sheets. • As contribution of mid area of GO increase on fiber surface cotton fabric becomes more hydrophobic. • Amphiphilic property of GO sheets was used to lower the surface energy of the cotton fibers leading to hydrophobic property. - Abstract: We report for the first time hydrophobic properties on cotton fabric successfully achieved by grafting graphene oxide on the fabric surface, using a dyeing method. Graphite oxide synthesized by oxidizing natural flake graphite employing improved Hummer's method showed an inter layer spacing of ∼1 nm from XRD. Synthesized graphite oxide was exfoliated in water using ultrasound energy to obtain graphene oxide (GO). AFM data obtained for the graphene oxide dispersed in an aqueous medium revealed a non-uniform size distribution. FTIR characterization of the synthesized GO sheets showed both hydrophilic and hydrophobic functional groups present on the nano sheets giving them an amphiphilic property. GO flakes of different sizes were successfully grafted on to a cotton fabric surface using a dip dry method. Loading different amounts of graphene oxide on the cotton fiber surface allowed the fabric to demonstrate different degrees of hydrophobicity. The highest observed water contact angle was at 143° with the highest loading of graphene oxide. The fabric surfaces grafted with GO also exhibits adhesive type hydrophobicity

Identification of skin-expressed genes possibly associated with wool growth regulation of Aohan fine wool sheep

OpenAIRE

Liu, Nan; Li, Hegang; Liu, Kaidong; Yu, Juanjuan; Bu, Ran; Cheng, Ming; De, Wei; Liu, Jifeng; He, Guangling; Zhao, Jinshan

2014-01-01

Background Sheep are valuable resources for the animal fibre industry. Therefore, identifying genes which regulate wool growth would offer strategies for improving the quality of fine wool. In this study, we employed Agilent sheep gene expression microarray and proteomic technology to compare the gene expression patterns of the body side (hair-rich) and groin (hairless) skins of Aohan fine wool sheep (a Chinese indigenous breed). Results Comparing the body side to the groin skins (S/G) of Aoh...

Cotton nanofibers obtained by different acid conditions

International Nuclear Information System (INIS)

Teixeira, Eliangela de M.; Oliveira, Caue Ribeiro de; Mattoso, Luiz H.C.; Correa, Ana Carolina; Palladin, Priscila

2009-01-01

The thermal stability of cellulose nanofibers is related to their application and especially to polymer processing which temperatures of processing are around 200 deg C. In this work, nanofibers of commercial cotton were obtained by acid hydrolysis employing different acids: sulfuric, hydrochloric and a mixture (2:1; sulfuric acid: hydrochloric acid).The morphology of the nanofibers were characterized by transmission microscopy (TEM), crystallinity by x-ray diffraction (XRD) and thermal stability in air atmosphere by thermogravimetric analysis (TGA). The results indicated a very similar morphology and crystallinity among them. The main differences were relative to aggregation state e and thermal stability. The aggregation state of the suspensions decreases in the order HCl 2 SO 4 :HCl 2 SO 4- . The hydrolysis with a mix of HCl and H 2 SO 4 resulted in cellulose nanofibers with higher thermal stability than those hydrolyzed with H 2 SO 4 . The hydrolysis employed with a mixture of sulphuric and hydrochloric acids also showed a better dispersion than those suspensions of nanofibers obtained by hydrolysis with only HCl. (author)

Hydrophilicity improvement of polyethersulfone membranes by grafting methacrylic acid with γ-ray irradiation

International Nuclear Information System (INIS)

Li Jing; Hou Zhengchi; Xie Leidong; Zhang Fengying; Deng Bo

2005-01-01

Grafting methyacrylic acid onto poly(ether sulfone) membranes was realized by means of simultaneous irradiation in liquids. The modified membranes with different grafting ratios were obtained by changing the concentration of methyacrylic acid. It was shown that the grafting ratio increased lineally as the monomer concentration was less than 10% and hydrophilicity of the membranes was improved with increasing grafting ratios. (authors)

Synthesis, characterization, bioactivity and potential application of phenolic acid grafted chitosan: A review.

Science.gov (United States)

Liu, Jun; Pu, Huimin; Liu, Shuang; Kan, Juan; Jin, Changhai

2017-10-15

In recent years, increasing attention has been paid to the grafting of phenolic acid onto chitosan in order to enhance the bioactivity and widen the application of chitosan. Here, we present a comprehensive overview on the recent advances of phenolic acid grafted chitosan (phenolic acid-g-chitosan) in many aspects, including the synthetic method, structural characterization, biological activity, physicochemical property and potential application. In general, four kinds of techniques including carbodiimide based coupling, enzyme catalyzed grafting, free radical mediated grafting and electrochemical methods are frequently used for the synthesis of phenolic acid-g-chitosan. The structural characterization of phenolic acid-g-chitosan can be determined by several instrumental methods. The physicochemical properties of chitosan are greatly altered after grafting. As compared with chitosan, phenolic acid-g-chitosan exhibits enhanced antioxidant, antimicrobial, antitumor, anti-allergic, anti-inflammatory, anti-diabetic and acetylcholinesterase inhibitory activities. Notably, phenolic acid-g-chitosan shows potential applications in many fields as coating agent, packing material, encapsulation agent and bioadsorbent. Copyright © 2017 Elsevier Ltd. All rights reserved.

Gamma radiation effects on fattly acid composition of lipids in cotton leaves

International Nuclear Information System (INIS)

Arslanova, S.V.; Stepanenko, G.A.; Umarov, A.K.; Nazirov, N.N.

1976-01-01

The mechanism of high irradiation dose (30 kR) effect on the lipid fatty acid composition of cotton leaves was studied in the ontogenesis. The experiment was carried out in vegetation vials (capacity 25 kg, humidity level - 65% of full water capacity). Before seeding, each vial was fertilized with 5g P 2 O 5 , 3g K 2 O and 5gN as an auxillary nutrition during vegetation. The test vials also contained 0.4 - 0.5 g CaO per kg of soil. A portion of irradiated seeds was soaked in 1.5% solution of CaO and Ca(NO 3 ) 2 before seeding. The cotton seeds were gamma-irradiated at 50 R/sec in the Institute of Nuclear Physics, Usbec SSR Academy of Sciences. The fatty acid composition of mature leaf lipids determined by gas-liquid chromatography proved to change in the blooming phase. Leaves of irradiated plants contained traces of myristic acid, higher levels of palmitic, palmitoleinic and strearinic acids and lower levels of oleinic and linoleic acids. Lower content of fatty acids with long carbon chains seemed to handicap the renewal of membranes and their components, especially in mitochondria. When irradiated seeds were soaked in calcium salt solution and CaO is added to the soil, the amount of unsaturated long chain fatty acids increased. The fact probably promotes the membrane renewal in irradiated plants

Enhancement of flame retardancy and water repellency properties of cotton fabrics using silanol based nano composites.

Science.gov (United States)

Mohamed, Amina L; El-Sheikh, Manal A; Waly, Ahmed I

2014-02-15

Environmental concerns related to fluorinated and organophosphorus compounds led to a consideration of the methods for imparting flame retardancy and water/oil repellency to textiles. A simple and facile method for fabricating the cotton fabric with superhydrophobicity and flame retardancy is described in the present work. Complex coating with amino-functionalized silica nano-particles on epoxy-functionalized cotton accompanied with ZnO nano-particles coating are carried out. In This context, new preparation techniques were used to prepare both aminated silica and ZnO nano-particles. The particle size was investigated using Transition Electron Microscope (TEM) and the chemical structure was investigated using FT-IR analysis and other analytical techniques. Cotton was functionalized with epoxy and carboxyl via grafting cotton with nano-emulsion consisted of mixture of glycidyl methacrylate (GMA) and acrylic acid (AA), and then treated for functional finishing through conventional pad-dry-cure method. The treated fabrics showed good water repellency and excellent flame retardant properties as determined by the standard test methods. Copyright © 2013 Elsevier Ltd. All rights reserved.

Confirmation and quantification of strigolactones, germination stimulants for root parasitic plants Striga and Orobanche, produced by cotton.

Science.gov (United States)

Sato, Daisuke; Awad, Ayman A; Takeuchi, Yasutomo; Yoneyama, Koichi

2005-01-01

The germination stimulants for root parasitic plants Striga and Orobanche produced by cotton (Gossypium hirsutum L.) were examined in detail. Seeds of cotton were germinated and grown on glass wool wetted with sterile distilled water in sterile filter units. The root exudate was collected daily and extracted with ethyl acetate. Each of these ethyl acetate extracts was analyzed directly by high-performance liquid chromatography linked with tandem mass spectrometry (LC/MS/MS). The results demonstrate that cotton roots exuded strigol and strigyl acetate, but no other known strigolactones such as orobanchol and alectrol. The production of strigol was detected even in the root exudate collected during the first 24 h of incubation and reached a maximum 5-7 days later. The average exudation of strigol and strigyl acetate during the incubation period was ca. 15 and 2 pg/plant/day, respectively, indicating that strigol mainly contributed to germination stimulation by the cotton root exudate.

Production of mineral ash-wool

International Nuclear Information System (INIS)

Micevic, Z.; Djekic, S.

1996-01-01

The project entitled 'Production of Mineral Ash-Wool' presents a new technology of possible use of the fly ash, generated as a waste product from the fossil fueled power plants, as a basic raw material for manufacturing of different products from a new mineral ash-wool. The wide area of mineral ash-wool application (civil engineering, industry, power generation, etc.) and the advantages of this new technology (important raw material obtained free of charge, substitution of expensive silicate stone, use of electric energy for melting instead for coke, vicinity of factory location close to the fossil fueled power plant, lower product price, reduction of environmental pollution, etc.) have resulted in the performance of the bench scale tests. Positive results have been obtained, as a good initial base for the realization of this project. The named study as an detailed analysis has been carried out for the assessment of: supply and sales market, analysis of possible and selection of an optimal location of the factory in the frame of fossil fueled power plant 'Kosovo', selection of the production capacity and alternative preliminary technical designs of the factory for the mineral ash-wool production. For the studied alternatives, specifications and capital investments evaluations for equipment and works (mechanical, civil engineering and electromechanical part) have been made as well as assessments of production costs. Based on the performed economical and financial analyses, as well as the sensitivity analyses one could be concluded that the investments in the factory for the mineral ash-wool production is highly economically acceptable. (author). 1 fig., 1 tab., 3 refs

Enhancement of nitric oxide release and hemocompatibility by surface chirality of D-tartaric acid grafting

Science.gov (United States)

Han, Honghong; Wang, Ke; Fan, Yonghong; Pan, Xiaxin; Huang, Nan; Weng, Yajun

2017-12-01

Nitric Oxide (NO) generation from endogenous NO-donors catalyzed by diselenide modified biomaterials has been reported. Here we reported surface chirality by L-tartaric acid and D-tartaric acid grafting on the outermost showed a significant impact on diselenide modified biomaterials, which modulated protein adsorption, NO release and anti-platelet adhesion properties. D-tartaric acid grafted surface showed more blood protein adsorption than that of L-surfaces by QCM analysis, however, ELISA analysis disclosed less fibrinogen denatured on the D surfaces. Due to the surface ratio of selenium decreasing, NO release catalyzed by L-tartaric acid grafting on the outermost significantly decreased in comparison to that of only selenocystamine immobilized surfaces. While NO release catalyzed by D-tartaric acid grafting on the outermost didn't decrease and was similar with that of selenocystamine immobilized surfaces. Surface chirality combined with NO release had synergetic effects on platelet adhesion, and it showed the lowest number of platelets adhered on the D-tartaric acid grafted surfaces. Thus surface chirality from D-tartaric acid grafting enhanced hemocompatibility of the surface in this study. Our work provides new insights into engineering novel blood contacting biomaterials by taking into account surface chirality.

Melting behaviour of raw materials and recycled stone wool waste

DEFF Research Database (Denmark)

Schultz-Falk, Vickie; Agersted, Karsten; Jensen, Peter Arendt

2018-01-01

Stone wool is a widely used material for building insulation, to provide thermal comfort along with fire stability and acoustic comfort for all types of buildings. Stone wool waste generated either during production or during renovation or demolition of buildings can be recycled back into the sto...... wool melt production. This study investigates and compares the thermal response and melting behaviour of a conventional stone wool charge and stone wool waste. The study combines differential scanning calorimetry (DSC), hot stage microscopy (HSM) and X-ray diffraction (XRD). DSC reveals...... that the conventional charge and stone wool waste have fundamentally different thermal responses, where the charge experiences gas release, phase transition and melting of the individual raw materials. The stone wool waste experiences glass transition, crystallization and finally melting. Both DSC and HSM measurements...

Dressing for alveolopalatal wounds after alveolar bone grafting.

Science.gov (United States)

Kondoh, Shoji; Matsuo, Kiyoshi; Yuzuriha, Shunsuke; Kikuchi, Nirou; Ban, Ryokuya

2003-09-01

Cotton gauze with alpha cyanoacrylate was used for alveolopalatal wound dressing after alveolar bone grafting to treat 93 alveolar clefts in 74 cleft patients to reduce mechanical injuries, tension for wound dehiscence, and adhesion of food remnants. T-shaped cotton gauze was put on the gingivoperiosteal flaps and was impregnated with cyanoacrylate. The procedure required no preoperative preparation and its intraoperative execution took less than 5 minutes. The gauze with cyanoacrylate was removed approximately 1 week after surgery. No infection was observed at any of the operational sites, but tiny fistulas developed at four of them. The mean bone graft score was 1.4 point. No complications such as thermal injury resulted from the use of cyanoacrylate. Gauze impregnated with cyanoacrylate proved to be a convenient and dependable dressing for alveolopalatal wounds resulting from gingivoperiosteoplasty for alveolar bone grafting.

Hydrophilicity improvement of polyethersulfone powders by grafting acrylic acid with γ-ray simultaneous irradiation method

International Nuclear Information System (INIS)

Deng Bo; Hou Zhengchi; Zhang Fengying; Xie Leidong; Li Jing; Yang Haijun

2005-01-01

Acrylic acid was grafted to Polyethersulfone (PES) powders by liquid-phase simultaneous irradiation. Effects of grafting conditions, such as absorbed dose, volume fraction of monomer, inhibitor (Cu 2+ ) concentration, and pH of the grafting solution on degree of the grafting were investigated. Combined with gravimetric analysis, a working curve of grafting degree through FT-IR quantitative analysis was obtained. The highest grafting degree was achieved at dose of 25 kGy, volume fraction of monomer of 30% and inhibitor concentration of 0.004 mol/L. Greater degrees of the grafting could be obtained by adding increasing amount of hydrochloric acid to the system. Hydrophilicity of the grafted PES powders increased with higher degrees of the grafting. (authors)

Grafting of acrylic acid onto polypropylene films irradiated with argon ions

International Nuclear Information System (INIS)

Massa, G.; Mazzei, R.; Garcia Bermudez, G.; Filevich, A.; Smolko, E.

2005-01-01

Polypropylene (PP) foils were irradiated with 100 keV energy Argon ions at different fluences ranging from 10 12 up to 2 x 10 15 cm -2 and then grafted with acrylic acid (AA). The grafting yield was measured by weight difference and the structural changes on the films were analysed using Fourier transform infrared spectroscopy (FTIR). Different parameters that determined the grafting process such us fluence, grafting time and monomer concentration were analysed. The grafting reached an optimum value at 79% in aqueous solution at 30 min grafting time. The grafting yield as a function of the ion fluence plot, presented a maximum value, as previously found in a study of heavy beam on polymers

Devitrification and high temperature properties of mineral wool

DEFF Research Database (Denmark)

Nielsen, Eva Ravn; Augustesen, Maria; Ståhl, Kenny

2007-01-01

spectroscopy, secondary neutral mass spectroscopy, differential scanning calorimetry and thermal gravimetric analysis. When stone wool fibres were heated at 800 ºC in air, oxidation of Fe2+ to Fe3+ occurred simultaneously with migration of divalent cations (especially Mg2+) to the surface. Decreasing Fe3......Mineral wool products can be used for thermal and acoustic insulation as well as for fire protection. The high temperature properties and the crystallization behaviour (devitrification) of the amorphous fibres during heating have been examined. Commercial stone wool and commercial hybrid wool......+/Fetotal ratios resulted in increasing migration and improved thermal stability. The cations formed a surface layer mainly consisting of MgO. When heated to above 800 ºC, bulk crystallization of the fibres took place with diopside and nepheline as the main crystalline phases. Commercial stone wool...

Fabrication of cotton fabric with superhydrophobicity and flame retardancy.

Science.gov (United States)

Zhang, Ming; Wang, Chengyu

2013-07-25

A simple and facile method for fabricating the cotton fabric with superhydrophobicity and flame retardancy is described in the present work. The cotton fabric with the maximal WCA of 160° has been prepared by the covalent deposition of amino-silica nanospheres and the further graft with (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane. The geometric microstructure of silica spheres was measured by transmission electron microscopy (TEM). The cotton textiles before and after treatment were characterized by using scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The wetting behavior of cotton samples was investigated by water contact angle measurement. Moreover, diverse performances of superhydrophobic cotton textiles have been evaluated as well. The results exhibited the outstanding superhydrophobicity, excellent waterproofing durability and flame retardancy of the cotton fabric after treatment, offering a good opportunity to accelerate the large-scale production of superhydrophobic textiles materials for new industrial applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Preparation and characterization of poly(acrylic acid)-hydroxyethyl cellulose graft copolymer.

Science.gov (United States)

Abdel-Halim, E S

2012-10-01

Poly(acrylic acid) hydroxyethyl cellulose [poly(AA)-HEC] graft copolymer was prepared by polymerizing acrylic acid (AA) with hydroxyethyl cellulose (HEC) using potassium bromate/thiourea dioxide (KBrO(3)/TUD) as redox initiation system. The polymerization reaction was carried out under a variety of conditions including concentrations of AA, KBrO(3) and TUD, material to liquor ratio and polymerization temperature. The polymerization reaction was monitored by withdrawing samples from the reaction medium and measuring the total conversion. The rheological properties of the poly(AA)-HEC graft copolymer were investigated. The total conversion and rheological properties of the graft copolymer depended on the ratio of KBrO(3) to TUD and on acrylic acid concentration as well as temperature and material to liquor ratio. Optimum conditions of the graft copolymer preparation were 30 mmol KBrO(3) and 30 mmol TUD/100g HEC, 100% AA (based on weight of HEC), duration 2h at temperature 50 °C using a material to liquor ratio of 1:10. Copyright © 2012. Published by Elsevier Ltd.

Radiation-induced graft polymerization of acrylic acid onto fluorinated polymers: Pt. 2

International Nuclear Information System (INIS)

Abdel-Ghaffar, M.; Hegazy, E.A.; Dessouki, A.M.; El-Sawy, N.M.; El-Assy, N.B.

1991-01-01

Radiation induced grafting of acrylic acid onto poly (tetrafluoroethylene-perfluorovinyl ether) (PFA) films was investigated. The grafted films rapidly absorbed Fe 3+ , Co 2+ , Ni 2+ , and Cu 2+ ions in high efficiency. The polyacrylic acid grafted onto PFA acted as a chelating site for the previously selected transition metal ions. Such prepared copolymer-metal complexes were confirmed spectrophotometrically via IR, UV-spectrometry, X-ray fluorescence, X-ray diffraction, and colour index measurements. Electrical conductivity and mechanical properties of PFA grafted copolymer-metal complexes were investigated. The applications of such prepared copolymer-metal complexes in the field of semiconductors besides its performance as a cation-exchange membrane may be of great interest. (author)

Wool-waste as organic nutrient source for container-grown plants

Energy Technology Data Exchange (ETDEWEB)

Zheljazkov, Valtcho D. [Mississippi State University, North Mississippi Research and Extension Center, Verona, MS 38879 (United States)], E-mail: vj40@pss.msstate.edu; Stratton, Glenn W [Department of Plant and Animal Sciences and Department of Environmental Sciences, Nova Scotia Agricultural College, Truro, NS, B2N 5E3 (Canada); Pincock, James [Department of Chemistry, Dalhousie University, Halifax, NS, B3H 4J3 (Canada); Butler, Stephanie [Department of Plant and Animal Sciences and Department of Environmental Sciences, Nova Scotia Agricultural College, Truro, NS, B2N 5E3 (Canada); Jeliazkova, Ekaterina A [Mississippi State University, Department of Plant and Soil Sciences, Mississippi State, MS 39762 (United States); Nedkov, Nedko K [Research Institute for Roses and Aromatic Crops, 49 Osvobojdenie Blv., Kazanluk (Bulgaria); Gerard, Patrick D [Department of Applied Economics and Statistics, Clemson University, Clemson, SC 29634 (United States)

2009-07-15

A container experiment was conducted to test the hypothesis that uncomposted wool wastes could be used as nutrient source and growth medium constituent for container-grown plants. The treatments were: (1) rate of wool-waste application (0 or unamended control, 20, 40, 80, and 120 g of wool per 8-in. pot), (2) growth medium constituents [(2.1) wool plus perlite, (2.2) wool plus peat, and (2.3) wool plus peat plus perlite], and (3) plant species (basil and Swiss chard). A single addition of 20, 40, 80, or 120 g of wool-waste to Swiss chard (Beta vulgaris L.) and basil (Ocimum basilicum L.) in pots with growth medium provided four harvests of Swiss chard and five harvests of basil. Total basil yield from the five harvests was 1.6-5 times greater than the total yield from the unamended control, while total Swiss chard yield from the four harvests was 2-5 times greater relative to the respective unamended control. The addition of wool-waste to the growth medium increased Swiss chard and basil tissue N, and NO{sub 3}-N and NH{sub 4}-N in growth medium relative to the unamended control. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) microanalysis of wool fibers sampled at the end of the experiments indicated various levels of decomposition, with some fibers retaining their original surface structure. Furthermore, most of the wool fibers' surfaces contained significant concentrations of S and much less N, P, or K. SEM/EDX revealed that some plant roots grow directly on wool-waste fibers suggesting either (1) root directional growth towards sites with greater nutrient concentration and/or (2) a possible role for roots or root exudates in wool decomposition. Results from this study suggest that uncomposted wool wastes can be used as soil amendment, growth medium constituent, and nutrient source for container-grown plants.

Wool-waste as organic nutrient source for container-grown plants

International Nuclear Information System (INIS)

Zheljazkov, Valtcho D.; Stratton, Glenn W.; Pincock, James; Butler, Stephanie; Jeliazkova, Ekaterina A.; Nedkov, Nedko K.; Gerard, Patrick D.

2009-01-01

A container experiment was conducted to test the hypothesis that uncomposted wool wastes could be used as nutrient source and growth medium constituent for container-grown plants. The treatments were: (1) rate of wool-waste application (0 or unamended control, 20, 40, 80, and 120 g of wool per 8-in. pot), (2) growth medium constituents [(2.1) wool plus perlite, (2.2) wool plus peat, and (2.3) wool plus peat plus perlite], and (3) plant species (basil and Swiss chard). A single addition of 20, 40, 80, or 120 g of wool-waste to Swiss chard (Beta vulgaris L.) and basil (Ocimum basilicum L.) in pots with growth medium provided four harvests of Swiss chard and five harvests of basil. Total basil yield from the five harvests was 1.6-5 times greater than the total yield from the unamended control, while total Swiss chard yield from the four harvests was 2-5 times greater relative to the respective unamended control. The addition of wool-waste to the growth medium increased Swiss chard and basil tissue N, and NO 3 -N and NH 4 -N in growth medium relative to the unamended control. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) microanalysis of wool fibers sampled at the end of the experiments indicated various levels of decomposition, with some fibers retaining their original surface structure. Furthermore, most of the wool fibers' surfaces contained significant concentrations of S and much less N, P, or K. SEM/EDX revealed that some plant roots grow directly on wool-waste fibers suggesting either (1) root directional growth towards sites with greater nutrient concentration and/or (2) a possible role for roots or root exudates in wool decomposition. Results from this study suggest that uncomposted wool wastes can be used as soil amendment, growth medium constituent, and nutrient source for container-grown plants.

Utilization of Mineral Wools as Alkali-Activated Material Precursor

Directory of Open Access Journals (Sweden)

Juho Yliniemi

2016-04-01

Full Text Available Mineral wools are the most common insulation materials in buildings worldwide. However, mineral wool waste is often considered unrecyclable because of its fibrous nature and low density. In this paper, rock wool (RW and glass wool (GW were studied as alkali-activated material precursors without any additional co-binders. Both mineral wools were pulverized by a vibratory disc mill in order to remove the fibrous nature of the material. The pulverized mineral wools were then alkali-activated with a sodium aluminate solution. Compressive strengths of up to 30.0 MPa and 48.7 MPa were measured for RW and GW, respectively, with high flexural strengths measured for both (20.1 MPa for RW and 13.2 MPa for GW. The resulting alkali-activated matrix was a composite-type in which partly-dissolved fibers were dispersed. In addition to the amorphous material, sodium aluminate silicate hydroxide hydrate and magnesium aluminum hydroxide carbonate phases were identified in the alkali-activated RW samples. The only crystalline phase in the GW samples was sodium aluminum silicate. The results of this study show that mineral wool is a very promising raw material for alkali activation.

Preparation of poly(vinyl alcohol) membranes grafted with N-vinyl imidazole/acrylic acid binary monomers

International Nuclear Information System (INIS)

Ajji, Zaki; Ali, Ali

2006-01-01

Poly(vinyl alcohol) films were grafted with two monomers using gamma radiation, acrylic acid and N-vinyl imidazole. The influence of different parameters on the grafting yield was investigated as: type of solvent and solvent composition, comonomer concentration and composition, addition of mineral acids, and irradiation dose. Water uptake in respect to the grafting yield was also evaluated. The ability of the grafted films to adsorb copper ions was elaborated and discussed for different grafting yields and ph values of the solution. (authors)

Modification of carbon fiber surfaces via grafting with Meldrum's acid

International Nuclear Information System (INIS)

Cuiqin, Fang; Jinxian, Wu; Julin, Wang; Tao, Zhang

2015-01-01

Graphical abstract: - Highlights: • The mechanism of Meldrum's acid modifying carbon fiber surfaces was investigated. • The existing carbonyl groups of carbon fibers were grafted with Meldrum's acid. • The relative content of carboxylic groups on carbon fiber surfaces was increased. • The surfaces of carbon fibers neither etched nor generated coating. • Tensile strength of carbon fibers was preserved after grafting reaction. - Abstract: The mechanism of Meldrum's acid modifying carbon fiber surfaces was investigated in this work. The existing carbonyl groups of carbon fibers were grafted with Meldrum's acid to create carboxylic functionalized surfaces. The surface functionalization effect was detected with X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), atomic force microscopy (AFM), and thermogravimetric analysis (TGA). The XPS results showed that the relative content of carboxylic groups on carbon fiber surfaces was increased from initial 1.41% to 7.84%, however, that of carbonyl groups was decreased from 23.11% to 13.28% after grafting reaction. The SEM, AFM and TGA results indicated that the surfaces of carbon fibers neither etched nor generated coating. The tensile strength of carbon fibers was preserved after grafting reaction according to single fiber tensile strength tests. The fibers were well combined with matrix and the maximal interlaminar shear strength (ILSS) of carbon fiber/epoxy resin composites was sharply increased approximately 74% after functionalization. The effects of acetic acid and sonication on the degree of the surface functionalization were also studied.

Modification of carbon fiber surfaces via grafting with Meldrum's acid

Energy Technology Data Exchange (ETDEWEB)

Cuiqin, Fang; Jinxian, Wu [Beijing Key Laboratory of Electrochemical Process and Technology for Materials, Beijing University of Chemical Technology, Beijing 100029 (China); Julin, Wang, E-mail: wjl@mail.buct.edu.cn [Beijing Key Laboratory of Electrochemical Process and Technology for Materials, Beijing University of Chemical Technology, Beijing 100029 (China); Tao, Zhang [Beijing Institute of Ancient Architecture, Beijing 100050 (China)

2015-11-30

Graphical abstract: - Highlights: • The mechanism of Meldrum's acid modifying carbon fiber surfaces was investigated. • The existing carbonyl groups of carbon fibers were grafted with Meldrum's acid. • The relative content of carboxylic groups on carbon fiber surfaces was increased. • The surfaces of carbon fibers neither etched nor generated coating. • Tensile strength of carbon fibers was preserved after grafting reaction. - Abstract: The mechanism of Meldrum's acid modifying carbon fiber surfaces was investigated in this work. The existing carbonyl groups of carbon fibers were grafted with Meldrum's acid to create carboxylic functionalized surfaces. The surface functionalization effect was detected with X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), atomic force microscopy (AFM), and thermogravimetric analysis (TGA). The XPS results showed that the relative content of carboxylic groups on carbon fiber surfaces was increased from initial 1.41% to 7.84%, however, that of carbonyl groups was decreased from 23.11% to 13.28% after grafting reaction. The SEM, AFM and TGA results indicated that the surfaces of carbon fibers neither etched nor generated coating. The tensile strength of carbon fibers was preserved after grafting reaction according to single fiber tensile strength tests. The fibers were well combined with matrix and the maximal interlaminar shear strength (ILSS) of carbon fiber/epoxy resin composites was sharply increased approximately 74% after functionalization. The effects of acetic acid and sonication on the degree of the surface functionalization were also studied.

Thrombin immobilization to methacrylic acid grafted poly(3-hydroxybutyrate) and its in vitro application.

Science.gov (United States)

Akkaya, Alper; Pazarlioglu, Nurdan

2013-01-01

Poly(3-hydroxybutyrate) is nontoxic and biodegradable, with good biocompatibility and potential support for long-term implants. For this reason, it is a good support for enzyme immobilization. Enzyme immobilization could not be done directly because poly(3-hydroxybutyrate) has no functional groups. Therefore, modification should be done for enzyme immobilization. In this study, methacrylic acid was graft polymerized to poly(3-hydroxybutyrate) and thrombin was immobilized to polymethacrylic acid grafted poly(3-hydroxybutyrate). In fact, graft polymerization of methacrylic acid to poly(3-hydroxybutyrate) and thrombin immobilization was a model study. Biomolecule immobilized poly(3-hydroxybutyrate) could be used as an implant. Thrombin was selected as a biomolecule for this model study and it was immobilized to methacrylic acid grafted poly(3-hydroxybutyrate). Then the developed product was used to stop bleeding.

Radiation-induced graft copolymerization of methyl acrylate and acrylic acid onto rubber wood fiber

International Nuclear Information System (INIS)

Saliza Jam; Mansor Ahmad; Wan Md Zin Wan Yunus; Khairul Zaman Mohd Dahlan

2001-01-01

Graft copolymerization of methyl acrylate and acrylic acid monomers onto rubber wood fiber (RWF) was carried out by simultaneous radiation-induced technique. The parameters affecting the grafting reaction were investigated and the optimum conditions for both monomers obtained are as follows: impregnation time = 16 hours, total dose = 30 kGy, methanol : water ratio, 3:1, monomers concentration = 40 v/v % and sulphuric acid concentration = 0.1 mol/L. Fourier Transform Infrared (FTIR), thermogravimetry analysis (TGA), and scanning electron microscope (SEM) analyses used to characterize graft copolymers. The structural investigation by x-ray diffraction (XRD) shows the degree of crystallinity of rubber wood fiber decreased with the incorporation of poly(methyl acrylate) and poly(acrylic acid) grafts. (Author)

Characterization of Functionalized Acrylic acid /4- Vinyl Pyridine Graft Copolymers

International Nuclear Information System (INIS)

Kamal, H.; Mahmoud, Gh.A.; Hegazy, D.E.

2009-01-01

Properties and characterization of the membranes prepared by radiation grafting of acrylic acid (AAc) or/ and 4-vinyl pyridine (4VP) onto low density polyethylene (LDPE) and polypropylene (PP) films were carried out. The FTIR spectra for the grafted membranes were studied to evaluate the structure change as a result of grafting. The swelling behaviour of the graft copolymer in methanol was studied. It was found that the grafting of AAc and/ or 4- VP onto LDPE and PP resulted in introducing good hydrophilic properties to such polymer substrates. The hydrophilic properties were directly proportional to the amount of functional groups. The mechanical properties (Young's modulus, elongation percent and tensile strength) of the grafted membranes also, have been investigated. As the grafting degree increases, the modulus also increases. Increasing the hydrophilicity of the membranes by chemical treatment enhances its mechanical properties. The thermal parameters of the grafted membranes such as δH m1 . δH m2 , and T rc have been also studied by using DSC

Measurement of sound propagation in glass wool

DEFF Research Database (Denmark)

Tarnow, Viggo

1995-01-01

A new acoustic method for directly measuring the flow resistance, and the compressibility of fibrous materials such as glass wool, is given. Measured results for monochromatic sound in glass wool are presented and compared with theoretically calculated results. The agreement between experimental...

Radiation synthesis of chitosan beads grafted with acrylic acid for metal ions sorption

International Nuclear Information System (INIS)

Benamer, S.; Mahlous, M.; Tahtat, D.; Nacer-Khodja, A.; Arabi, M.; Lounici, H.; Mameri, N.

2011-01-01

Radiation-induced grafting of acrylic acid onto chitosan beads was performed in solution at a dose rate of 20.6 Gy/min of cobalt-60 gamma rays. The effect of absorbed dose on grafting yield was investigated. The characterization of the grafted material was performed by FTIR spectroscopy and the swelling measurements at different pHs. The grafting yield increased with the increase in dose, it reached 80% at 40 kGy irradiation dose. The removal of Pb and Cd ions from aqueous solutions was investigated with both ungrafted and grafted chitosan beads. The sorption behavior of the sorbents was examined through pH, kinetics and equilibrium measurements. Grafted chitosan beads presented higher sorption capacity for both metal ions than unmodified chitosan beads. - Highlights: → Pb and Cd ions are removed from aqueous solution by adsorption on chitosan beads. → Crosslinking process improves chemical stability of chitosan beads. → Radiation grafting of acrylic acid onto chitosan improves its metal adsorption capacity. → Increase in grafting degree enhances the adsorption capacity of the material. → Gamma radiation is a powerful tool for an accurate control of the grafting yield.

Steric Stabilization of “Charge-Free” Cellulose Nanowhiskers by Grafting of Poly(ethylene glycol

Directory of Open Access Journals (Sweden)

Jun Araki

2014-12-01

Full Text Available A sterically stabilized aqueous suspension of “charge-free” cellulose nanowhiskers was prepared by hydrochloric acid hydrolysis of cotton powders and subsequent surface grafting of monomethoxy poly(ethylene glycol (mPEG. The preparation scheme included carboxylation of the terminal hydroxyl groups in mPEG via oxidation with silica gel particles carrying 2,2,6,6-tetramethyl-1-pyperidinyloxyl (TEMPO moieties and subsequent esterification between terminal carboxyls in mPEG and surface hydroxyl groups of cellulose nanowhiskers, mediated by 1,1'-carbonyldiimidazole (CDI in dimethyl sulfoxide or dimethylacetamide. Some of the prepared PEG-grafted samples showed remarkable flow birefringence and enhanced stability after 24 h, even in 0.1 M NaCl, suggesting successful steric stabilization by efficient mPEG grafting. Actual PEG grafting via ester linkages was confirmed by attenuated total reflectance-Fourier transform infrared spectrometry. In a typical example, the amount of grafted mPEG was estimated as ca. 0.3 g/g cellulose by two measurements, i.e., weight increase after grafting and weight loss after alkali cleavage of ester linkages. Transmission electron microscopy indicated unchanged nanowhisker morphology after mPEG grafting.

Modification of carbon fiber surfaces via grafting with Meldrum's acid

Science.gov (United States)

Cuiqin, Fang; Jinxian, Wu; Julin, Wang; Tao, Zhang

2015-11-01

The mechanism of Meldrum's acid modifying carbon fiber surfaces was investigated in this work. The existing carbonyl groups of carbon fibers were grafted with Meldrum's acid to create carboxylic functionalized surfaces. The surface functionalization effect was detected with X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), atomic force microscopy (AFM), and thermogravimetric analysis (TGA). The XPS results showed that the relative content of carboxylic groups on carbon fiber surfaces was increased from initial 1.41% to 7.84%, however, that of carbonyl groups was decreased from 23.11% to 13.28% after grafting reaction. The SEM, AFM and TGA results indicated that the surfaces of carbon fibers neither etched nor generated coating. The tensile strength of carbon fibers was preserved after grafting reaction according to single fiber tensile strength tests. The fibers were well combined with matrix and the maximal interlaminar shear strength (ILSS) of carbon fiber/epoxy resin composites was sharply increased approximately 74% after functionalization. The effects of acetic acid and sonication on the degree of the surface functionalization were also studied.

Thermoresponsive PNIPAAm-modified cotton fabric surfaces that switch between superhydrophilicity and superhydrophobicity

International Nuclear Information System (INIS)

Jiang Cheng; Wang Qihua; Wang Tingmei

2012-01-01

Thermoresponsive poly(N-isopropylacrylamide) (PNIPAAm) was grafted onto the cotton fabric by atom transfer radical polymerization (ATRP). Introducing 1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTS) onto the surface, the density of PNIPAAm chains can be adjusted because of the competitive reactions of (3-aminopropyl) triethoxysilane (APS) and PFDTS. With the appropriate ratio of APS and PFDTS, the cotton fabric can be switched from superhydrophilic to superhydrophobic by controlling temperature. The prepared cotton fabric may find application in functional textiles, soft and folding superhydrophobic materials.

Major genes and QTL influencing wool production and quality: a review

Directory of Open Access Journals (Sweden)

Purvis Ian

2005-12-01

Full Text Available Abstract The opportunity exists to utilise our knowledge of major genes that influence the economically important traits in wool sheep. Genes with Mendelian inheritance have been identified for many important traits in wool sheep. Of particular importance are genes influencing pigmentation, wool quality and the keratin proteins, the latter of which are important for the morphology of the wool fibre. Gene mapping studies have identified some chromosomal regions associated with variation in wool quality and production traits. The challenge now is to build on this knowledge base in a cost-effective way to deliver molecular tools that facilitate enhanced genetic improvement programs for wool sheep.

The crosstalk between Target of Rapamycin (TOR) and Jasmonic Acid (JA) signaling existing in Arabidopsis and cotton.

Science.gov (United States)

Song, Yun; Zhao, Ge; Zhang, Xueyan; Li, Linxuan; Xiong, Fangjie; Zhuo, Fengping; Zhang, Chaojun; Yang, Zuoren; Datla, Raju; Ren, Maozhi; Li, Fuguang

2017-04-04

Target of rapamycin (TOR) acts as an important regulator of cell growth, development and stress responses in most examined diploid eukaryotes. However, little is known about TOR in tetraploid species such as cotton. Here, we show that TORC1-S6K-RPS6, the major signaling components, are conserved and further expanded in cotton genome. Though the cotton seedlings are insensitive to rapamycin, AZD8055, the second-generation inhibitor of TOR, can significantly suppress the growth in cotton. Global transcriptome analysis revealed that genes associated with jasmonic acid (JA) biosynthesis and transduction were significantly altered in AZD8055 treated cotton seedlings, suggesting the potential crosstalk between TOR and JA signaling. Pharmacological and genetic approaches have been employed to get further insights into the molecular mechanism of the crosstalk between TOR and JA. Combination of AZD8055 with methyl jasmonate can synergistically inhibit cotton growth, and additionally JA levels were significantly increased when cotton seedlings were subjected to AZD8055. JA biosynthetic and signaling mutants including jar1, coi1-2 and myc2-2 displayed TOR inhibitor-resistant phenotypes, whereas COI1 overexpression transgenic lines and jaz10 exhibited sensitivity to AZD8055. Consistently, cotton JAZ can partially rescue TOR-suppressed phenotypes in Arabidopsis. These evidences revealed that the crosstalk between TOR and JA pathway operates in cotton and Arabidopsis.

Study on radiation grafting of acrylic acid onto fluorine-containing polymers. II. Properties of membrane obtained by preirradiation grafting onto poly(tetrafluoroethylene)

International Nuclear Information System (INIS)

Hegazy, E.S.A.; Ishigaki, I.; Rabie, A.; Dessouki, A.M.; Okamoto, J.

1981-01-01

Some properties of the membranes obtained by the preirradiation grafting of acrylic acid onto poly(tetrafluoroethylene) (PTFE) film have been studied. The dimensional change by grafting and swelling, water uptake, electric conductivity, and mechanical properties of the grafted PTFE films were measured and were found to increase as the grafting proceeds. These properties were found to be dependent mainly on the degree of grafting regardless of grafting conditions except higher monomer concentration (80 wt %). The electric conductivity and mechanical properties of the membranes at 80 wt % monomer concentration is lower than those at a lower monomer concentration. The results suggest that the membranes obtained at 80-wt % acrylic acid solution have a somewhat heterogeneous distribution of electrolyte groups as compared with those prepared at a monomer concentration less than 60 wt %. X-ray microscopy of the grafted films revealed that the grafting begins at the part close to the film surface and proceeds into the center with progressive diffusion of monomer to give finally the homogeneous distribution of electrolyte groups. The membranes show good electrochemical and mechanical properties which make them acceptable for the practical uses as cation exchange membrane

Permeability of solutes through cellophanes grafted with vinyl monomers. I. Diffusion of potassium chloride, urea, and uric acid

International Nuclear Information System (INIS)

Takigami, S.; Maeda, Y.; Nakamura, Y.

1979-01-01

The diffusive permeability of potassium chloride, urea, and uric acid through cellophanes grafted with acrylamide, acrylic acid, styrene, and N-vinyl-2-pyrrolidone by γ-ray irradiation was studied. The diffusive permeability coefficients of the permeants through the grafted cellophanes were increased with increase in hydration of the grafted membranes, except for the permeation of potassium chloride through cellophanes grafted with acrylic acid. The permeation of potassium chloride, urea, and uric acid through the various grafted cellophanes is explained by the free volume concept of homogeneously water-swollen membranes. However, the behavior of the permeation of potassium chloride through cellophane grafted with acrylic acid deviated from that of nonionic membranes because of the contribution of the electrical interaction between electrolyte and charge of the membrane. 4 figures, 3 tables

Characteristics Of Virgin And Pulled Wool Fibres Used In Tunisian Handmade Carpets

Directory of Open Access Journals (Sweden)

Taoufik Harizi

2015-08-01

Full Text Available Abstract Many factors such as production methods fibre quality and structural parameters have distinctive influence on the quality and performance of a hand woven carpet. Because the most common fiber used for producing handmade carpet is wool this experiment was aimed to identify virgin and pulled wool characteristics of Tunisian sheep breeds. A total of 84 sheep and 15 samples of commercial pulled wool were used in this study. Samples of fiber were analyzed using standard objective measurements for staple length SL mean fiber diameter MFD coefficient of variation of fiber diameter FDCV fine fiber contain FC Breaking strength and Elongation. Results showed that Tunisian wool can be considered as medium wool. By conducting well-planned sorting Fine Queue of west sheep breed can supply the wool needed for textile industries. The wool of other sheep breeds can be used in handmade carpets. Also staple strength as one of the important wool characteristic affected significantly by alkali treatment during chemical unhairing process compared with wool collected by shearing process. Great attention must be paid to know the real characteristics of pulled wool before using it in handmade carpet industry.

Synthesis and characterization of amylose grafted poly(acrylic acid) and its application in ammonia adsorption.

Science.gov (United States)

Chen, Qing; Yu, Haojie; Wang, Li; Abdin, Zain-Ul; Yang, Xinpeng; Wang, Junhua; Zhou, Weidong; Zhang, Hongtao; Chen, Xiao

2016-11-20

Amylose grafted poly(acrylic acid) (Am-g-PAA) was synthesized by graft copolymerization of amylose with acrylic acid. The structure of Am-g-PAA was confirmed by (1)H NMR and FT-IR spectra. The morphology, crystallinity and thermal properties of amylose and Am-g-PAA were investigated by SEM, XRD and TGA, respectively. The highest degree of substitution (DS) of carboxyl group was 1.96 which was obtained after reacted for 1h at 60°C. Acrylic acid to anhydroglucose mole ratio for DS was 19.81. It was found that a large number of carboxyl groups were grafted on the backbone of amylose. It was also found that ammonia adsorption capacity of amylose increased by grafting poly(acrylic acid) on the backbone of amylose. Copyright © 2016 Elsevier Ltd. All rights reserved.

In Vitro Antioxidant-Activity Evaluation of Gallic-Acid-Grafted Chitosan Conjugate Synthesized by Free-Radical-Induced Grafting Method.

Science.gov (United States)

Hu, Qiaobin; Wang, Taoran; Zhou, Mingyong; Xue, Jingyi; Luo, Yangchao

2016-07-27

The major objective of this work was to develop a green and facile process to prepare gallic acid-chitosan conjugate and comprehensively evaluate the physicochemical properties and biological activities of an as-prepared water-soluble chitosan derivative. A free-radical-induced grafting approach using an ascorbic acid-hydrogen peroxide redox pair was adopted. The obtained conjugate was characterized by Fourier transform infrared spectroscopy, UV-vis, X-ray diffraction, and pKa analysis. The antioxidant activities were evaluated by 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2'-azino-bis(3-ethylbenzothiazoline-6)-sulphonic acid (ABTS), reducing power, and oxygen-radical antioxidant-capacity assays. The results showed that the mass ratio of gallic acid to chitosan played a vital role in determining the grafting degree and ζ potential of the conjugates, with the ratio of 0.5:1 being the optimal ratio that resulted in the highest grafting degree. The antioxidant assays demonstrated that conjugation significantly improved the antioxidant activities, being dramatically higher than that of free chitosan. It was notable that the DPPH- and ABTS-scavenging activities of conjugate at 0.4 mg/mL reached the same level as the free gallic acid at the equivalent concentration. Our study demonstrated a green and facile synthesis approach to preparing a novel water-soluble chitosan derivative that may have promising potentials in the food industry.

Permeability of solutes through cellophanes grafted with vinyl monomers. II. Diffusion of potassium chloride through cellophanes grafted with acrylic acid

International Nuclear Information System (INIS)

Takigami, S.; Maeda, Y.; Nakamura, Y.

1979-01-01

The permeability behavior of potassium chloride through cellophane grafted with acrylic acid by a γ-irradiation method was studied by the theoretical equation derived from the phenomenological equation and compared with the results of Donnan membrane equilibrium. It was shown that the permeation of potassium chloride through the grafted cellophanes exhibited behavior typical of a polyionic membrane for grafts of more than 55% but depended on the permeability of both cellophane and graft regions for lower percents of grafting. It was found that the dominant factor affecting the permeation of potassium chloride was an effective concentration of fixed charge in the membrane. 5 figures, 2 tables

A review of raw wool carbonising

CSIR Research Space (South Africa)

Mozes, TE

1986-04-01

Full Text Available by means of a series of heavy crush rollers, mounted on roller bearings. The dust resulting from the crushing is removed in a deduster or &eying machine, which has an adjustable speed to cater for different types of wool and incorporates specially... , INTRODUCTION I 2. CONVENTIONALCARBONISING O F WOOL .................................. 1 2.1 Scouring 2 . . . 2.2 Actdmng ....................................................................................... 2 2.2.1 AcidisinaConditions and their Effect...

Grafting of polyethylene films with acrylic acid and acrylonitril using gamma radiation

International Nuclear Information System (INIS)

Ajji, Z.; Al-Nesr, E.

2003-12-01

Acrylic acid (AAc) and acrylonitrile (AN) and their binary mixtures were graft copolymerized onto low density polyethylene (LDPE) films using gamma irradiation. The effects of different parameters on the graft yield were studies such as monomer concentration, inhibitor concentration, and irradiation dose. The obtained grafted films were characterized using FTIR spectroscopy, thermal gravimetry, and differential scanning calorimetry. Water uptake and the ion uptake were also evaluated, and the ability of grafted films to uptake heavy ions such as Ni 2+ and Cu 2+ was discussed. (author)

Strength and Fractography of Glass Wool Fibres

DEFF Research Database (Denmark)

Lund, Majbritt Deichgræber; Yue, Yuanzheng

  Glass wool fibres (GWFs) are produced using the cascade spinning process. The lengths of the fibers range from 1 to 4 cm, whereas the diameters range from 4 and 10 mm. GWFs are widely used as insulation material due to their excellent heat and sound isolation effect, chemical durability, and high...... between fracture strength (sf) and mirror radius (r), i.e., sf = A*r, is confirmed for all the GWFs studied. The materials constant, A, (mirror constant) is found to be 2.4 ~ 2.7 MPam½ for basaltic wool and 2.0 MPam½ for E-glass wool, which is similar to the value reported in the literature for different...

Synthesis and property characterization of cassava starch grafted poly(acrylamide-co-(maleic acid)) superabsorbent via γ-irradiation

International Nuclear Information System (INIS)

Kiatkamjornwong, Suda; Mongkolsawat, Kanlaya; Sonsuk, Manit

2004-01-01

Graft copolymerizations of acrylamide and maleic acid onto cassava starch by a simultaneous irradiation technique using γ-rays as a initiator were carried out. Various important parameters of total dose, dose rate, monomer-to-cassava starch ratio and maleic acid content were studied. Addition of 2% ww -1 diprotic acid of maleic acid into the reaction mixture yields a saponified starch graft copolymer with a water absorption in distilled water as high as 2256g g -1 of its dried weight. The water absorption of these saponified graft copolymers insaline and buffer solutions was also measured. The water absorption depends largely on the cationic type and concentration of these solutions in terms of ionic strength. This research explains a charge transfer mechanism for graft copolymerization of maleic acid and acrylamide onto cassava starch, and describes the influential parameters that affect grafting efficiency and water absorption. (author)

Superamphiphobic cotton fabrics with enhanced stability

Energy Technology Data Exchange (ETDEWEB)

Xu, Bi, E-mail: xubi@dhu.edu.cn [National Engineering Research Center for Dyeing and Finishing of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of Science & Technology of Eco-Textile, Ministry of Education, Donghua University, Shanghai 201620 (China); College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China); Ding, Yinyan; Qu, Shaobo [College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China); Cai, Zaisheng, E-mail: zshcai@dhu.edu [College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China)

2015-11-30

Highlights: • Superamphiphobic cotton fabrics were prepared. • Water and hexadecane contact angels reach to 164.4° and 156.3°, respectively. • Nanoporous organically modified silica alcogel particles were synthesized. • The superamphiphobic cotton fabrics exhibit enhanced stability against abrasion, laundering and acid. - Abstract: Superamphiphobic cotton fabrics were prepared by alternately depositing organically modified silica alcogel (ormosil) particles onto chitosan precoated cotton fabrics and subsequent 1H, 1H, 2H, 2H-perfluorooctyltrimethoxysilane (PFOTMS) modification. Transmission electron microscopy and scanning electron microscopy images reveal that the ormosil particles display a fluffy, sponge-like nanoporous structure, and the entire cotton fiber surface is covered with highly porous networks. PFOTMS acts as not only a modifier to lower the surface energy of the cotton fabric but also a binder to enhance the coating stability against abrasion and washing. The treated cotton fabrics show highly liquid repellency with the water, cooking oil and hexadecane contact angels reaching to 164.4°, 160.1° and 156.3°, respectively. Meanwhile, the treated cotton fabrics exhibit good abrasion resistance and high laundering durability, which can withstand 10,000 cycles of abrasion and 30 cycles of machine wash without apparently changing the superamphiphobicity. The superamphiphobic cotton fabric also shows high acid stability, and can withstand 98% H{sub 2}SO{sub 4}. Moreover, the superamphiphobic coating has almost no influence on the other physical properties of the cotton fabrics including tensile strength, whiteness and air permeability. This durable non-wetting surface may provide a wide range of new applications in the future.

Wool fibril sponges with perspective biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Patrucco, A., E-mail: a.patrucco@bi.ismac.cnr.it [CNR-ISMAC, Italian National Research Council, Institute for Macromolecular Studies, Corso G. Pella 16, 13900, Biella (Italy); Cristofaro, F., E-mail: francesco.cristofaro01@universitadipavia.it [Department of Molecular Medicine, INSTM UdR of Pavia, University of Pavia, Viale Taramelli 3/B, 27100, Pavia (Italy); Centre for Health Technologies (CHT), University of Pavia, Via Ferrata 1, 27100, Pavia (Italy); Simionati, M., E-mail: m.simionati@bi.ismac.cnr.it [CNR-ISMAC, Italian National Research Council, Institute for Macromolecular Studies, Corso G. Pella 16, 13900, Biella (Italy); Zoccola, M., E-mail: m.zoccola@bi.ismac.cnr.it [CNR-ISMAC, Italian National Research Council, Institute for Macromolecular Studies, Corso G. Pella 16, 13900, Biella (Italy); Bruni, G., E-mail: giovanna.bruni@unipv.it [Department of Chemistry, — Physical-Chemistry Section, University of Pavia, Viale Taramelli 16, 27100, Pavia (Italy); Fassina, L., E-mail: lorenzo.fassina@unipv.it [Centre for Health Technologies (CHT), University of Pavia, Via Ferrata 1, 27100, Pavia (Italy); Department of Electrical, Computer and Biomedical Engineering, University of Pavia, Via Ferrata 1, 27100, Pavia (Italy); Visai, L., E-mail: livia.visai@unipv.it [Department of Molecular Medicine, INSTM UdR of Pavia, University of Pavia, Viale Taramelli 3/B, 27100, Pavia (Italy); Centre for Health Technologies (CHT), University of Pavia, Via Ferrata 1, 27100, Pavia (Italy); Department of Occupational Medicine, Toxicology and Environmental Risks, S. Maugeri Foundation, IRCCS, Via S. Boezio, 28, 27100, Pavia (Italy); Magenes, G., E-mail: giovanni.magenes@unipv.it [Centre for Health Technologies (CHT), University of Pavia, Via Ferrata 1, 27100, Pavia (Italy); Department of Electrical, Computer and Biomedical Engineering, University of Pavia, Via Ferrata 1, 27100, Pavia (Italy); and others

2016-04-01

Sheep's wool was used as a natural source to prepare keratin microfibril sponges for scaffolding, by disruption of the histological structure of the fibres through mild alkali treatment, followed by ultrasonication, casting and salt-leaching. The wool sponges showed highly interconnected porosity (93%) and contain intrinsic sites of cellular recognition that mimic the extracellular matrix (ECM). They displayed good thermal and water stability due to the conversion of disulphide cystine bonds into shorter monosulphide lanthionine intermolecular bonds, but significantly swelled in water, because of the high hydrophilicity and porosity, with a volume increasing up to 38%. Nevertheless, sponges were stable in water without structural changes, with a neutral pH in aqueous media, and showed excellent resilience to repeated compression stresses. According to in vitro biocompatibility assays, wool fibril sponges showed a good cell adhesion and proliferation as proved by MTT, FDA assays and SEM observations. The unique structure of the cortical cell network made by wool keratin proteins with controlled-size macro-porosity suitable for cell guesting, and nutrient feeding, provides an excellent scaffold for future tissue engineering applications. - Highlights: • Scaffolds were prepared from wool exploiting the fibres' histology structure. • The scaffold showed high interconnected micro- and macro-porosity. • The microscopic structure is very similar to the extracellular bone matrix. • Scaffolds reversibly swell in water with high resilience to repeated compression. • Composites were cytocompatible and supported the growth of SAOS-2 cell line.

Wool fibril sponges with perspective biomedical applications

International Nuclear Information System (INIS)

Patrucco, A.; Cristofaro, F.; Simionati, M.; Zoccola, M.; Bruni, G.; Fassina, L.; Visai, L.; Magenes, G.

2016-01-01

Sheep's wool was used as a natural source to prepare keratin microfibril sponges for scaffolding, by disruption of the histological structure of the fibres through mild alkali treatment, followed by ultrasonication, casting and salt-leaching. The wool sponges showed highly interconnected porosity (93%) and contain intrinsic sites of cellular recognition that mimic the extracellular matrix (ECM). They displayed good thermal and water stability due to the conversion of disulphide cystine bonds into shorter monosulphide lanthionine intermolecular bonds, but significantly swelled in water, because of the high hydrophilicity and porosity, with a volume increasing up to 38%. Nevertheless, sponges were stable in water without structural changes, with a neutral pH in aqueous media, and showed excellent resilience to repeated compression stresses. According to in vitro biocompatibility assays, wool fibril sponges showed a good cell adhesion and proliferation as proved by MTT, FDA assays and SEM observations. The unique structure of the cortical cell network made by wool keratin proteins with controlled-size macro-porosity suitable for cell guesting, and nutrient feeding, provides an excellent scaffold for future tissue engineering applications. - Highlights: • Scaffolds were prepared from wool exploiting the fibres' histology structure. • The scaffold showed high interconnected micro- and macro-porosity. • The microscopic structure is very similar to the extracellular bone matrix. • Scaffolds reversibly swell in water with high resilience to repeated compression. • Composites were cytocompatible and supported the growth of SAOS-2 cell line.

Preparation of membranes by radiation grafting of acrylic acid onto Teflon-FEP film

International Nuclear Information System (INIS)

Gupta, B.D.

1991-01-01

The grafting of acrylic acid on radiation-peroxidised Teflon-FEP film provides an effective technique to prepare ion-exchange membranes. It was found that the grafted membranes have very high degree of swelling in aqueous KOH. The electric resistance of the film decreases considerably by grafting. An electric resistance of 0.2Ω cm 2 was obtained for a graft level beyond 58%. The hydrophilicity of the film was evaluated in terms of contact angle which shows a decreasing trend with the increasing degree of grafting. (author). 8 refs

Radiation Induced Preparation of Polymer Membranes Grafted with Basic and Acidic Monomers for Application in Wastewater Treatment

Energy Technology Data Exchange (ETDEWEB)

Ajji, Z [Polymer Technology Division, Radiation Technology Department, Atomic Energy Commission of Syria (AECS), 17th Nissan Street, Kafar Sousah, Damascus (Syrian Arab Republic)

2012-09-15

Polymer membranes (PP and PE) had been grafted with basic and acidic functional groups using gamma radiation. Two binary mixtures had been used for the grafting reactions: acrylic acid/N-vinyl pyrrolidone, and acrylic acid/N-vinyl imidazole. The influence of different reaction parameters on the grafting yield had been investigated as: type of solvent and solvent composition, comonomer concentration and composition, addition of inhibitors, and dose. Water uptake with respect to the grafting yield had also been evaluated. The ability of PP films, grafted with acrylic acid/ vinyl pyrrolidone, to uptake heavy metal ions such as Hg{sup 2+}, Pb{sup 2+}, Cd{sup 2+}, Co{sup 2+}, Ni{sup 2+} and Cu{sup 2+} was elaborated. The uptake of the metal ions increases with increasing the grafting yield. Furthermore, the Pb{sup +2} uptake was much higher than the uptake of the Hg{sup 2+} and Cd{sup 2+} ions. The membranes may be considered for the separation of Pb{sup 2+} ions from Hg{sup 2+} or Cd{sup 2+} ions. Also the ability of PE films, grafted with acrylic acid/ N-vinyl imidazole to uptake heavy metal ions such as Pb{sup 2+}, Cd{sup 2+}, Co{sup 2+} and Ni{sup 2+} was elaborated. An increase in the uptake of the metal ions was observed as the grafting yield increased. (author)

Fabrication of boronate-decorated polyhedral oligomeric silsesquioxanes grafted cotton fiber for the selective enrichment of nucleosides in urine.

Science.gov (United States)

Gao, Li; Wei, Yinmao

2016-06-01

Various cotton fiber based boronate-affinity adsorbents are recently developed for the sample pretreatment of cis-diol-containing biomolecules, but most do not have efficient capacity due to limited binding sites on the surface of cotton fibers. To increase the density of boronate groups on the surface of cotton fiber, polyhedral oligomeric silsesquioxanes were used to modify cotton fiber to provide plentiful reactive sites for subsequent functionalization with 4-formylphenylboronic acid. The new adsorbent showed special recognition ability towards cis-diols and high adsorption capacity (175 μg/g for catechol, 250 μg/g for dopamine, 400 μg/g for adenosine). The in-pipette-tip solid-phase extraction was investigated under different conditions, including pH and ionic strength of solution, adsorbent amount, pipette times, washing solvent, and elution solvent. The in-pipette-tip solid-phase extraction coupled with high-performance liquid chromatography was used to analyze four nucleosides in urine samples. Under the optimal extraction conditions, the detection limits were determined to be between 5.1 and 6.1 ng/mL (S/N  =  3), and the linearity ranged from 20 to 500 ng/mL for these analytes. The accuracy of the analytical method was examined by studying the relative recoveries of analytes in real urine samples with recoveries varying from 83 to 104% (RSD = 3.9-10.2%, n = 3). © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Effects of cotton stalk biochar on microbial community structure and function of continuous cropping cotton rhizosphere soil in Xinjiang, China].

Science.gov (United States)

Gu, Mei-ying; Tang, Guang-mu; Liu, Hong-liang; Li, Zhi-qiang; Liu, Xiao-wei; Xu, Wan-li

2016-01-01

In this study, field trials were conducted to examine the effects of cotton stalk biochar on microbial population, function and structural diversity of microorganisms in rhizosphere soil of continuous cotton cropping field in Xinjiang by plate count, Biolog and DGGE methods. The experiment was a factorial design with four treatments: 1) normal fertilization with cotton stalk removed (NPK); 2) normal fertilization with cotton stalk powdered and returned to field (NPKS); 3) normal fertilization plus cotton stalk biochar at 22.50 t · hm⁻² (NPKB₁); and 4) normal fertilization plus cotton stalk biochar at 45.00 t · hm⁻² (NPKB₂). The results showed that cotton stalk biochar application obviously increased the numbers of bacteria and actinomycetes in the rhizospheric soil. Compared with NPK treatment, the number of fungi was significantly increased in the NPKB₁treatment, but not in the NPKB₂ treatment. However, the number of fungi was generally lower in the biochar amended (NPKB₁, NPKB₂) than in the cotton stalk applied plots (NPKS). Application of cotton stalk biochar increased values of AWCD, and significantly improved microbial richness index, suggesting that the microbial ability of utilizing carbohydrates, amino acids and carboxylic acids, especially phenolic acids was enhanced. The number of DGGE bands of NPKB₂ treatment was the greatest, with some species of Gemmatimonadetes, Acidobacteria, Proteobacteria and Actinobacteria being enriched. UPGMC Cluster analysis pointed out that bacterial communities in the rhizospheric soil of NPKB₂ treatment were different from those in the NPK, NPKS and NPKB₁treatments, which belonged to the same cluster. These results indicated that application of cotton stalk biochar could significantly increase microbial diversity and change soil bacterial community structure in the cotton rhizosphere soil, thus improving the health of soil ecosystem.

Preparation of poly (vinyl alcohol) membranes grafted with n-vinyl pyridine/ acrylic acid binary monomers

International Nuclear Information System (INIS)

Ajji, A.; Ali, A.

2014-03-01

Poly(vinyl alcohol) films were grafted with two monomers using gamma radiation, acrylic acid and N-vinyl pyridine. The influence of different parameters on the grafting yield was investigated as: the comonomer concentration and composition, and irradiation dose. The suitable conditions of the process had been determined to prepare PVA membranes have both properties of the two monomers, acrylic acid and vinyl pyridine as comonomer concentration and composition, and irradiation dose. Some properties of the membranes had been investigated as maximum swelling and grafting. Also the ability of the grafted films to adsorb some heavy metals and dyes was elaborated and discussed.(author)

Suppression of jasmonic acid-dependent defense in cotton plant by the mealybug Phenacoccus solenopsis.

Directory of Open Access Journals (Sweden)

Pengjun Zhang

Full Text Available The solenopsis mealybug, Phenacoccus solenopsis, has been recently recognized as an aggressively invasive pest in China, and is now becoming a serious threat to the cotton industry in the country. Thus, it is necessary to investigate the molecular mechanisms employed by cotton for defending against P. solenopsis before the pest populations reach epidemic levels. Here, we examined the effects of exogenous jasmonic acid (JA, salicylic acid (SA, and herbivory treatments on feeding behavior and on development of female P. solenopsis. Further, we compared the volatile emissions of cotton plants upon JA, SA, and herbivory treatments, as well as the time-related changes in gossypol production and defense-related genes. Female adult P. solenopsis were repelled by leaves from JA-treated plant, but were not repelled by leaves from SA-treated plants. In contrast, females were attracted by leaves from plants pre-infested by P. solenopsis. The diverse feeding responses by P. solenopsis were due to the difference in volatile emission of plants from different treatments. Furthermore, we show that JA-treated plants slowed P. solenopsis development, but plants pre-infested by P. solenopsis accelerated its development. We also show that P. solenopsis feeding inhibited the JA-regulated gossypol production, and prevented the induction of JA-related genes. We conclude that P. solenopsis is able to prevent the activation of JA-dependent defenses associated with basal resistance to mealybugs.

DYEING COTTON WITH EISENIA BICYCLIS AS NATURAL DYE USING DIFFERENT BIOMORDANTS

Directory of Open Access Journals (Sweden)

BONET Mª Ángeles

2015-05-01

Full Text Available Natural dyes are known for their use in coloring of food substrate, leather as well as natural protein fibers like wool, silk and cotton as major areas of application since pre-historic times. Nowadays, there has been revival of the growing interest on the application of natural dyes on natural fibers due to worldwide environmental consciousness. Some researchers focus their studies on the improvement of these dyes using mordants. Most works use metallic mordants like aluminum or iron are used, but some of them are hazardous. In this work we used a biomordant to solve environmental problems caused by metallic mordants. The effects of chitosan weight molecular in mordanting on the dyeing characteristics and the UV protection property were examined in this study. Chitosan mordanted Eisenia Bicyclis dyed cotton showed better dyeing characteristic and higher UV protection property compared with undyed cotton fabric. To analyze the differences of the dyeing, reflection spectrophotometer was used, evaluating the results of CIELAB color difference values and the strength color (in terms of K/S value. We conclude that the type of chitosan used affect the dyeing efficiency and the UV protection, showing different behavior between dye sample using chitosan with low or medium molecular weight.

Effect of Gamma Irradiation Doses on Some Chemical Characteristics of Cotton Seed Oil

International Nuclear Information System (INIS)

Saleh, O.I.

2011-01-01

Cotton Seeds c.v. Giza 85 (Gossypium hirsutum L.) were exposed to gamma irradiation doses of 0.5, 1.0 and 1.5 kGy to improve some chemical characteristics of cotton seed oil i.e. saturated and unsaturated fatty acids, gossypol and βsitosterol that were bound oil. The presented study showed that, the saturated fatty acids; lauric, palmitic and stearic increased when the cotton seeds were exposed to gamma irradiation doses of 0.5 up to 1.5 kGy, On the other hand, arachidic acid content decreased in all the irradiated treatments compared with untreated cotton seed. The unsaturated fatty acid oleic was increased in irradiated cotton seed samples compared with untreated one, while linoleic, the major unsaturated fatty acid decreased in irradiated cotton seed oil than untreated seeds. Gossypol and βsitosterol, bound oil, in irradiated cotton seeds increased gradually with gamma irradiated doses compared with untreated control samples

Fabrication of high-performance poly(l-lactic acid)/lignin-graft-poly(d-lactic acid) stereocomplex films.

Science.gov (United States)

Liu, Rui; Dai, Lin; Hu, Li-Qiu; Zhou, Wen-Qin; Si, Chuan-Ling

2017-11-01

The need for green renewable alternatives such as lignin to traditional fillers has driven recent interest in polylactic acid blend materials. Herein, lignin-graft-polylactic acid copolymers (LG-g-PDLA, LG-g-PDLLA, and LG-g-PLLA) have been synthesized via ring-opening polymerization of d-, dl-, and l-lactic acid. Then poly(l-lactic acid)/lignin-graft-polylactic acid (PLLA/LG-g-PDLA, /LG-g-PDLLA, and /LG-g-PLLA) complex films have been prepared. The results showed that, compared with LG-g-PDLA and LG-g-PLLA, a small amount of LG-g-PDLA addition could improve the crystallization rate, reduce the glass transition temperature and cold crystallization temperature of PLLA due to the stereocomplex crystallites. The thermal stability, tensile strength and strain of the stereocomplex films were also enhanced. Moreover, the PLLA/LG-g-PDLA films have good ultraviolet resistance and excellent biocompatibility. This study provides a green approach to design advanced polylactic acid-based blends with renewable natural resources. Copyright © 2017 Elsevier B.V. All rights reserved.

Graft copolymerization of N-maleoyl-N-phthaloyl-chitosan (MAPHCS) and acrylic acid via γ-ray irradiation

International Nuclear Information System (INIS)

Mu Qing; Fang Yue'e

2006-01-01

Chitosan is a well-known abundant natural polymer with good biodegradability, biocompatibility and bioactivity. But its insolubility in common organic solvents of chitosan have hindered its utilization and basic research. N-maleoyl-N-phthaloyl-chitosan (MAPHCS), soluble in DMF or DMSO, was synthesized and characterized by Fourier transform infrared spectra analysis (FT-IR) and 1 H-NMR. The graft copolymerization of acrylic acid onto chitosan was carried out with N-maleoyl-N-phthaloyl-chitosan as intermediate in homogeneous system and initiated by γ-irradiation. The double bond of MAPHCS may be the grafting site because the grafting field was much higher than that of the graft copolymerization of acrylic acid and phthaloylchitosan via γ-ray irradiation. The chemical structure of the graft copolymer was characterized by FT-IR and 1 H-NMR. As indicated in FTIR spectra, the evidence of the stronger absorbance at 2800-3000 cm -1 for C-H and at 1720 cm -1 for carboxyl group implied significantly the successful introduction of the poly (acrylic acid) on the chitosan chain. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) were also used to characterize the copolymer. Effects of synthesis variables on the graft copolymerization were studied in light of the grafting percentage. The grafting percentage increased with the dose at lower doses, and then decreased. The maximum grafting percentage was up to 132%. (authors)

Durable and Washable Antibacterial Copper Nanoparticles Bridged by Surface Grafting Polymer Brushes on Cotton and Polymeric Materials

Directory of Open Access Journals (Sweden)

Chufeng Sun

2018-01-01

Full Text Available To increase the durability of antibacterial coating on cotton and polymeric substrates, surface initiated grafting polymer brushes are introduced onto the substrates surface to bridge copper nanoparticles coatings and substrate. The morphologies of the composites consisting of the copper nanoparticles and polymer brushes were characterized with scanning electron microscopy (SEM. It was found that copper nanoparticles were uniformly and firmly distributed on the surfaces of the substrates by the polymer brushes; meanwhile, the reinforced concrete-like structures were formed in the composite materials. The substrates coated by the copper nanoparticles showed the efficient antibacterial activity against Staphylococcus aureus (S. aureus and Escherichia coli (E. coli even after washing by 30 cycles. The copper nanoparticles were tethered on the substrates by the strong chemical bonds, which led to the excellent washable fitness and durability. The change of the phase structure of the copper was analyzed to investigate the release mechanism of copper ions.

Genetic parameters of wool colour and skin traits in Corriedale sheep

Directory of Open Access Journals (Sweden)

M.V. Benavides

2003-01-01

Full Text Available Clean wool colour (CWC is an important wool price determinant and has been related to suint characteristics, i.e. sudoriparous and sebaceous gland secretions, such as suint percentage and suint K content. In this work heritability, phenotypic and genetic correlations among wool colour and skin traits were examined. The genetic estimates were assessed by Restricted Maximum Likelihood (REML procedures using average information algorithm (AIREML in a Corriedale flock. The traits analysed were wool colour traits (CWC, yellow predictive colour (YPC, and Visual Score; suint traits such as suint percentage and potassium and sodium concentrations in suint, and physiological traits such as potassium and sodium concentrations in the skin, including plasma and red blood cells. The objectives of this study were to assess phenotypic and genetic correlations between wool colour and skin traits, and to find the suitability of these traits as indirect selection criteria for clean wool colour. Suint traits were highly genetically correlated to YPC. Suint K, but not suint percentage, was found to have a high genetic correlation with CWC. Skin K, Visual Score, YPC and suint K were amongst the best indirect selection criteria for clean wool colour. However, selection using these traits was expected to reduce CWC from 52% to 49% of that estimated under direct selection.

Effect of mineral acid on polymer produced during radiation-induced grafting of styrene monomer

International Nuclear Information System (INIS)

Garnett, J.L.; Jankiewicz, S.V.; Sangster, D.F.

1982-01-01

The inclusion of mineral acid in a solution of styrene in methanol subjected to 60 Co γ irradiation markedly enhances the yield of monomer grafted to cellulose and other radiation grafting systems. Results were reported from a preliminary investigation into the mechanism of this acid effect through a study of the action of acid during the solution polymerization process. It was found that the presence of acid in a monomer solution such as styrene in 1, 4-dioxan led to an enhancement in the homopolymer yield of styrene; and it was showed that the acid also effected the number-average molecular weight of this homopolymer. 1 figure, 4 tables

Diversity in Betasatellites Associated with Cotton Leaf Curl Disease During Source-To-Sink Movement Through a Resistant Host

Directory of Open Access Journals (Sweden)

Iftikhar Ali Khan

2016-02-01

Full Text Available Cotton leaf curl is devastating disease of cotton characterized by leaf curling, vein darkening and enations. The disease symptoms are induced by DNA satellite known as Cotton leaf curl Multan betasatellite (CLCuMuB, dominant betasatellite in cotton but another betasatellite known as Chili leaf curl betasatellite (ChLCB is also found associated with the disease. Grafting experiment was performed to determine if host plant resistance is determinant of dominant population of betasatellite in cotton (several distinct strains of CLCuMuB are associated with the disease. Infected scion of Gossypium hirsutum collected from field (the source was grafted on G. arboreum, a diploid cotton species, resistant to the disease. A healthy scion of G. hirsutum (sink was grafted at the top of G. arboreum to determine the movement of virus/betasatellite to upper susceptible scion of G. hirsutum. Symptoms of disease appeared in the upper scion and presence of virus/betasatellite in the upper scion was confirmed via molecular techniques, showing that virus/betasatellite was able to move to upper scion through resistant G. arboreum. However, no symptoms appeared on G. arboreum. Betasatelites were cloned and sequenced from lower scion, upper scion and G. arboreum which show that the lower scion contained both CLCuMuB and ChLCB, however only ChLCB was found in G. arboreum. The upper scion contained CLCuMuB with a deletion of 78 nucleotides (nt in the non-coding region between A-rich sequence and βC1 gene and insertion of 27 nt in the middle of βC1 ORF. This study may help in investigating molecular basis of resistance in G. arboreum.

Oral delivery of insulin using pH-sensitive hydrogels based on polyvinyl alcohol grafted with acrylic acid/methacrylic acid by radiation

Energy Technology Data Exchange (ETDEWEB)

Nho, Young-Chang [Radiation Application Research Division, Korea Atomic Energy Research Institute, Daejeon 305-600 (Korea, Republic of)]. E-mail: ycnho@kaeri.re.kr; Park, Sung-Eun [Radiation Application Research Division, Korea Atomic Energy Research Institute, Daejeon 305-600 (Korea, Republic of); Kim, Hyung-Il [College of Engineering, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Hwang, Taek-Sung [College of Engineering, Chungnam National University, Daejeon 305-764 (Korea, Republic of)

2005-07-01

The pH-responsive hydrogels were studied as a drug carrier for the protection of insulin from the acidic environment of the stomach before releasing in the small intestine. Hydrogels based on poly(vinyl alcohol) networks grafted with acrylic acid or methacrylic acid were prepared via a two-step process. Poly(vinyl alcohol) hydrogels were prepared by gamma ray irradiation (50 kGy) and then followed by grafting either acrylic acid or methacrylic acid onto this poly(vinyl alcohol) hydrogels with subsequent irradiation (5-20 kGy). These graft hydrogels showed pH-sensitive swelling behavior. These hydrogels were used as carrier for the controlled release of insulin. The in vitro release of insulin was observed for the insulin-loaded hydrogels in a simulated intestinal fluid (pH 6.8) but not in a simulated gastric fluid (pH 1.2). The release behavior of insulin in vivo in a rat model confirmed the effectiveness of the oral delivery of insulin to control the level of glucose.

Oral delivery of insulin using pH-sensitive hydrogels based on polyvinyl alcohol grafted with acrylic acid/methacrylic acid by radiation

International Nuclear Information System (INIS)

Nho, Young-Chang; Park, Sung-Eun; Kim, Hyung-Il; Hwang, Taek-Sung

2005-01-01

The pH-responsive hydrogels were studied as a drug carrier for the protection of insulin from the acidic environment of the stomach before releasing in the small intestine. Hydrogels based on poly(vinyl alcohol) networks grafted with acrylic acid or methacrylic acid were prepared via a two-step process. Poly(vinyl alcohol) hydrogels were prepared by gamma ray irradiation (50 kGy) and then followed by grafting either acrylic acid or methacrylic acid onto this poly(vinyl alcohol) hydrogels with subsequent irradiation (5-20 kGy). These graft hydrogels showed pH-sensitive swelling behavior. These hydrogels were used as carrier for the controlled release of insulin. The in vitro release of insulin was observed for the insulin-loaded hydrogels in a simulated intestinal fluid (pH 6.8) but not in a simulated gastric fluid (pH 1.2). The release behavior of insulin in vivo in a rat model confirmed the effectiveness of the oral delivery of insulin to control the level of glucose

Study of PVC membrane grafted by Acrylic Acid, Acrylonitrile and Acrylamide using preirradiation method

International Nuclear Information System (INIS)

Kattan, M.; Al-Kasseri, H.

2015-03-01

Grafting of acrylic acid, acrylamide and acrylonitrile onto poly vinyl chloride (PVC) films using gamma radiation has been carried out by both type direct and preirradiation methods. The effect of different parameter such as monomer concentration, inhibitor concentration, reaction temperature, reaction time and irradiation dose on the grafting yield were investigated. It was found that the grafting yield depends on these parameters. The grafting yield was strongly monomer dependent and grafting method: the highest was found for AAc by the preirradiation method. The samples were characterized by tensile strength measurement, swilling and ion uptake. The highest increase in swilling was observed on samples grafted with AAc by the preirradiation method.(author)

Synthesis of ion exchange membrane by radiation grafting of acrylic acid onto polyethylene

International Nuclear Information System (INIS)

Ishigaki, I.; Sugo, T.; Senoo, K.; Takayama, T.; Machi, S.; Okamoto, J.; Okada, T.

1981-01-01

Radiation grafting of vinyl monomers onto polymer films has been extensively studied by many workers. In the preirradiation method of grafting a polymer substrate is activated by irradiation (either in the presence or absence of oxygen) and subsequently allowed to react with a monomer. The preirradiation method was utilized in this study to synthesize an ion exchange membrane useful for a battery separator by grafting acrylic acid onto polyethylene film. The battery separator should be chemically and thermally stable, sufficiently durable in electrolyte as well as highly electrically conductive. Membranes made from regenerated cellulose, e.g., cellophane, have long been used as a separator in the batteries with alkaline electrolyte, such as silver oxide primary cell. However, it has poor durability, as short as one year, due to breakdown of the membrane during operation or storing. The acrylic acid-grafted polyethylene film was found to be quite useful for a separator in the alkaline batteries. This membrane has a high electric conductivity and an excellent durability. (author)

Response of successive three generations of cotton bollworm, Helicoverpa armigera (Hübner), fed on cotton bolls, under elevated CO2

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

The growth, development and consumption of successive three generations of cotton bollworm, Helicoverpa armigera (Hübner), fed on cotton bolls grown under elevated CO2 (double-ambient vs. ambient) in open-top chambers were examined. Significant decreases in protein, total amino acid, water and nitrogen content and increases in free fatty acid were observed in cotton bolls. Changes in quality of cotton bolls affected the growth, development and food utilization of H. armigera. Significantly longer larval development duration in three successive generations and lower pupal weight of the second and third generations were observed in cotton bollworm fed on cotton bolls grown under elevated CO2. Significantly lower fecundity was also found in successive three generations of H. armigera fed on cotton bolls grown under elevated CO2. The consumption per larva occurred significant increase in successive three generations and frass per larva were also significantly increased during the second and third generations under elevated CO2. Significantly lower relative growth rate, efficiency of conversion of ingested food and significant higher relative consumption rate in successive three generations were observed in cotton bollworm fed on cotton bolls grown under elevated CO2. Significantly lower potential female fecundity, larval numbers and population consumption were found in the second and third generations of cotton bollworm fed on cotton bolls grown under elevated CO2. The integrative effect of higher larval mortality rate and lower adult fecundity resulted in significant decreases in potential population consumption in the latter two generations. The results show that elevated CO2 adversely affects cotton bolls quality, which indicates the potential population dynamics and potential population consumption of cotton bollworm will alleviate the harm to the plants in the future rising CO2 atmosphere.

Influence of dielectric barrier discharge treatment on mechanical and dyeing properties of wool

Science.gov (United States)

Rahul, NAVIK; Sameera, SHAFI; Md Miskatul, ALAM; Md Amjad, FAROOQ; Lina, LIN; Yingjie, CAI

2018-06-01

Physical and chemical properties of wool surface significantly affect the absorbency, rate of dye bath exhaustion and fixation of the industrial dyes. Hence, surface modification is a necessary operation prior to coloration process in wool wet processing industries. Plasma treatment is an effective alternative for physiochemical modification of wool surface. However, optimum processing parameters to get the expected modification are still under investigation, hence this technology is still under development in the wool wet processing industries. Therefore, in this paper, treatment parameters with the help of simple dielectric barrier discharge plasma reactor and air as a plasma gas, which could be a promising combination for treatment of wool substrate at industrial scale were schematically studied, and their influence on the water absorbency, mechanical, and dyeing properties of twill woven wool fabric samples are reported. It is expected that the results will assist to the wool coloration industries to improve the dyeing processes.

UV-induced graft polymerization of acrylic acid in the sub-micronchannels of oxidized PET track-etched membrane

Science.gov (United States)

Korolkov, Ilya V.; Mashentseva, Anastassiya A.; Güven, Olgun; Taltenov, Abzal A.

2015-12-01

In this article, we report on functionalization of track-etched membrane based on poly(ethylene terephthalate) (PET TeMs) oxidized by advanced oxidation systems and by grafting of acrylic acid using photochemical initiation technique for the purpose of increasing functionality thus expanding its practical application. Among advanced oxidation processes (H2O2/UV) system had been chosen to introduce maximum concentration of carboxylic acid groups. Benzophenone (BP) photo-initiator was first immobilized on the surfaces of cylindrical pores which were later filled with aq. acrylic acid solution. UV-irradiation from both sides of PET TeMs has led to the formation of grafted poly(acrylic acid) (PAA) chains inside the membrane sub-micronchannels. Effect of oxygen-rich surface of PET TeMs on BP adsorption and subsequent process of photo-induced graft polymerization of acrylic acid (AA) were studied by ESR. The surface of oxidized and AA grafted PET TeMs was characterized by UV-vis, ATR-FTIR, XPS spectroscopies and by SEM.

Aluminum Silicate Nanotube Modification of Cotton-Like Siloxane-poly(L-lactic acid-vaterite Composites

Directory of Open Access Journals (Sweden)

Daiheon Lee

2013-01-01

Full Text Available In our earlier work, a cotton-like biodegradable composite, consisting of poly(L-lactic acid with siloxane-containing vaterite, has been prepared by electrospinning. In the present work, the fibers skeleton of the cotton-like composites was modified successfully with imogolite, which is hydrophilic and biocompatible, via a dip process using ethanol diluted solution to improve the cellular initial attachment. Almost no change in the fiber morphology after the surface modification was observed. The surface-modified composite showed the similar calcium and silicate ions releasabilities, for activating the osteoblasts, as an unmodified one. Cell culture tests showed that the initial adhesion of murine osteoblast-like cells on the surface of the fibers was enhanced by surface modification.

Water absorbency of chitosan grafted acrylic acid hydrogels

Science.gov (United States)

Astrini, N.; Anah, L.; Haryono, A.

2017-07-01

Acrylic acid (AA) monomer was directly grafted onto chitosan (CTS) using potassium persulfate (KPS) as an initiator and methylenebisacrylamide (MBA) as a crosslinking agent under an inert atmosphere. One factor affecting the swelling capacity of the obtained hydrogel, KPS concentration, were studied. The hydrogel products were characterized using Fourier Transform Infrared spectroscopy (FTIR) for chemical structure and scanning electron microscopy (SEM) for morphology. Swelling of the hydrogel samples in distilled water and saline solution ( 9% NaCl ) was examined. Swelling capacity of the CTS-g-PAA hydrogels in distilled water (88.53 g/g) was higher than in NaCl solution (29.94 g/g) The highest swelling capacity value was obtained when the grafted reaction was carried out using 2.5wt% initiator

Organosilane grafted acid-activated beidellite clay for the removal of non-ionic alachlor and anionic imazaquin

International Nuclear Information System (INIS)

Paul, Blain; Martens, Wayde N.; Frost, Ray L.

2011-01-01

Clay adsorbents were prepared via two-step method to remove nonionic alachlor and anionic imazaquin herbicides from water. Firstly, layered beidellite clay, a member of smectite family, was treated with acid in hydrothermal process; secondly, common silane coupling agents, 3-chloro-propyl trimethoxysilane or triethoxy silane, were grafted on the acid treated samples to prepare adsorbent materials. The organically modified clay samples were characterized by powder X-ray diffraction, N 2 gas adsorption, and FTIR spectroscopy. It was found that the selective modification of clay samples displayed higher adsorption capacity for herbicides compared with acid activated clay. And the amount of adsorption is increased with increasing the grafting amount of silane groups. Clay grafted with 3-chloro-propyl trimethoxysilane is an excellent adsorbent for both alachlor and imazaquin but triethoxy (octyl) silane grafted clay is more efficient only for alachlor removal.

Characterization and modelling of the mechanical properties of mineral wool

DEFF Research Database (Denmark)

Chapelle, Lucie

2016-01-01

and as a consequence focus on the mechanical properties of mineral wool has intensified. Also understanding the deformation mechanisms during compression of low density mineral wool is crucial since better thickness recovery after compression will result in significant savings on transport costs. The mechanical...... properties of mineral wool relate closely to the arrangement and characteristics of the fibres inside the material. Because of the complex architecture of mineral wool, the characterization and the understanding of the mechanism of deformations require a new methodology. In this PhD thesis, a methodology...... of the structure on mechanical properties can be explored. The size of the representative volume elements for the prediction of the elastic properties is determined for two types of applied boundary conditions. For sufficiently large volumes, the predicted elastic properties are consistent with results from...

Genetic diversity/impurity estimation in sources of natural resistance against cotton leaf curl disease in pakistan

International Nuclear Information System (INIS)

Sarwar, G.

2007-01-01

Cotton accounts for more than 60% of Pakistan's export earnings through the export of both raw cotton and cotton products. An epidemic of cotton leaf curl disease (CLCuD) in Pakistan during the 1990s led to the withdrawal of high yielding cotton cultivars. Due of their susceptibility to the disease. The identification of natural resistance in some genotypes provided a means to manage reduce losses due to the disease. But it has been an adversity that almost all these resistant varieties have ultimately 'lost' their resistance. There are also reports that the original sources of resistance, as well as the varieties developed from them, are now susceptible to the disease when grafted with infected scion. For the present studies. Seed of two resistant varieties (LRA-5166 and (CP-152) was obtained from six different research organizations. Plants raised from these seed were grafted with symptomatic scion and used for morphological comparisons. Our results indicated that the genetic pool of these cultivars is not well maintained and that an unacceptable diversity impurity is present within and among the genetic stock of both these lines. There is thus a requirement for screening of these elite lines at the molecular level to ensure the purity of these varieties for future development. The virus causing CLCuD showed change by recombination making the search for new sources of resistance, as well as the maintenance of established sources, indispensable for the sustainable cotton production in Pakistan. (author)

78 FR 22369 - National Emissions Standards for Hazardous Air Pollutants: Mineral Wool Production and Wool...

Science.gov (United States)

2013-04-15

... furnace exhaust stack. Several HAP metals, including lead and arsenic, are released from the batch... insulation product; and 3. Flame attenuation wool fiberglass manufacturing lines producing a bonded pipe...

Graft polymerization of acrylic acid onto chitin nanofiber to improve dispersibility in basic water.

Science.gov (United States)

Ifuku, Shinsuke; Iwasaki, Masayoshi; Morimoto, Minoru; Saimoto, Hiroyuki

2012-09-01

Graft copolymerization of acrylic acid (AA) on chitin nanofibers was carried out with potassium persulfate as a free radical initiator in an aqueous medium. The molar ratio of grafted AA increased with the AA concentration. The grafted chitin nanofibers were characterized by FT-IR, FE-SEM, UV-vis, XRD, and TGA. After polymerization, the characteristic morphology of chitin nanofibers was maintained. Chitin nanofibers grafted with AA were efficiently dissociated and dispersed homogeneously in basic water because of the electrostatic repulsion effect between nanofibers. AA was grafted on the surface and amorphous part of chitin nanofibers, and the original crystalline structure of α-chitin was maintained. At 330 °C, the weight residue of the graft copolymer increased with the grafted AA content. Copyright © 2012 Elsevier Ltd. All rights reserved.

Preparation and study on the structure of keratin/PVA membrane containing wool fibers

Science.gov (United States)

Wu, Min; Shen, Shuming; Yang, Xuhong; Tang, Rencheng

2017-10-01

The urea / sodium sulfide / sodium dodecyl sulfate (SDS) method was used to dissolve the wool in this study. Then the Wool fiber/keratin/PVA composites with different proportions were prepared, and the surface morphology, molecular structure, mechanical property of the composite films and the influence of the proportions on their structure and properties were studied. The results showed that, there are α-helix structure, β-sheet and random coil conformations in the pure keratin film, as well as in the wool fiber. Compared with wool fiber, the crystallinity of keratin decreased. PVA can obviously improve the mechanical property of the blended film. When the blended ratio of keratin/PVA is 20/80, the mechanical property of the blended film is greatly improved. The composite films with 8%-16% of wool fibers have better flexibility than those without wool fibers.

Adsorption Properties of Lac Dyes on Wool, Silk, and Nylon

Directory of Open Access Journals (Sweden)

Bo Wei

2013-01-01

Full Text Available There has been growing interest in the dyeing of textiles with natural dyes. The research about the adsorption properties of natural dyes can help to understand their adsorption mechanism and to control their dyeing process. This study is concerned with the kinetics and isotherms of adsorption of lac dyes on wool, silk, and nylon fibers. It was found that the adsorption kinetics of lac dyes on the three fibers followed the pseudosecond-order kinetic model, and the adsorption rate of lac dyes was the fastest for silk and the slowest for wool. The activation energies for the adsorption process on wool, silk, and nylon were found to be 107.15, 87.85, and 45.31 kJ/mol, respectively. The adsorption of lac dyes on the three fibers followed the Langmuir mechanism, indicating that the electrostatic interactions between lac dyes and those fibers occurred. The saturation values for lac adsorption on the three fibers decreased in the order of wool > silk > nylon; the Langmuir affinity constant of lac adsorption on nylon was much higher than those on wool and silk.

Characterization and analysis of the cotton cyclopropane fatty acid synthase family and their contribution to cyclopropane fatty acid synthesis

Directory of Open Access Journals (Sweden)

Rawat Richa

2011-05-01

Full Text Available Abstract Background Cyclopropane fatty acids (CPA have been found in certain gymnosperms, Malvales, Litchi and other Sapindales. The presence of their unique strained ring structures confers physical and chemical properties characteristic of unsaturated fatty acids with the oxidative stability displayed by saturated fatty acids making them of considerable industrial interest. While cyclopropenoid fatty acids (CPE are well-known inhibitors of fatty acid desaturation in animals, CPE can also inhibit the stearoyl-CoA desaturase and interfere with the maturation and reproduction of some insect species suggesting that in addition to their traditional role as storage lipids, CPE can contribute to the protection of plants from herbivory. Results Three genes encoding cyclopropane synthase homologues GhCPS1, GhCPS2 and GhCPS3 were identified in cotton. Determination of gene transcript abundance revealed differences among the expression of GhCPS1, 2 and 3 showing high, intermediate and low levels, respectively, of transcripts in roots and stems; whereas GhCPS1 and 2 are both expressed at low levels in seeds. Analyses of fatty acid composition in different tissues indicate that the expression patterns of GhCPS1 and 2 correlate with cyclic fatty acid (CFA distribution. Deletion of the N-terminal oxidase domain lowered GhCPS's ability to produce cyclopropane fatty acid by approximately 70%. GhCPS1 and 2, but not 3 resulted in the production of cyclopropane fatty acids upon heterologous expression in yeast, tobacco BY2 cell and Arabidopsis seed. Conclusions In cotton GhCPS1 and 2 gene expression correlates with the total CFA content in roots, stems and seeds. That GhCPS1 and 2 are expressed at a similar level in seed suggests both of them can be considered potential targets for gene silencing to reduce undesirable seed CPE accumulation. Because GhCPS1 is more active in yeast than the published Sterculia CPS and shows similar activity when expressed in model

Gallic Acid Grafted Chitosan Has Enhanced Oxidative Stability in Bulk Oils.

Science.gov (United States)

Gim, Seo Yeong; Hong, Seungmi; Kim, Mi-Ja; Lee, JaeHwan

2017-07-01

Gallic acid (GA) was grafted in chitosan and the effects of GA grafted chitosan (GA-g-CS) on the oxidative stability in bulk oil was tested at 60 and 140 °C. To text oxidative stability in oils, headspace oxygen content, conjugated dienoic acid (CDA) value, p-anisidine value (p-AV), and acid value were determined. Chitosan itself did not show antioxidative or prooxidative effects in oils at 60 °C. However, GA-g-CS and GA acted as antioxidants at 60 °C. At 140 °C heating with moisture supplied condition, different results were observed. GA-g-CS acted as antioxidants based on the results of CDA and p-AV. However, chitosan showed the highest oxidative stability based on results of acid value and brown color formation at 140 °C. This could be due to reduction of moisture content by chitosan. GA was continuously released from GA-g-CS in bulk oil. This might have provided extra antioxidant activities to oils. © 2017 Institute of Food Technologists®.

A distributed knowledge-based system for the optimum utilisation of South African wool

Directory of Open Access Journals (Sweden)

Nomusa Dlodlo

2009-09-01

Full Text Available This article describes the concept and development of a knowledge-based advisory system for the optimum utilisation of South African wool for the benefit of present and potential investors and other interested parties. Wool is a natural animal fibre produced in varying quantities around the world. The wool fibre is far from homogenous; its type and quality, such as fineness and length, depending on the breed of sheep and the environmental conditions prevailing during its growth. Wool is used in a variety of end uses, ranging from fi ne worsted suiting, to hand knitting yarn, carpets, blankets and aircraft upholstery, its use depending largely on its fibre fineness and length. The wool industry is one of the oldest agricultural industries in South Africa, playing an important economic role as an earner of foreign exchange, and providing a living to many people. Wool is produced in many parts of South Africa under extensive, semi-extensive or intensive conditions, and is largely an export commodity. It is produced and traded in a sophisticated free market business environment into the international market place, where supply and demand forces determine price levels. More than 90% of locally produced wool is exported in an unprocessed or semi-processed form which detrimentally affects employment, foreign exchange and income-generating opportunities associated with value-addition prior to export. To reduce the amount of wool exported in unprocessed or semi-processed form, wool-processing enterprises need to be established to produce internationally marketable end products. Therefore, South Africa needs to attract investors into the wool sector, who will set up manufacturing mills in an economically sustainable manner. Potential and present investors in the South African (S.A. wool industry need easily accessible and up-to-date information on the production statistics, processing properties and end-use pplications of the wool they need for the

Improvement of pesticide adsorption capacity of cellulose fibre by high-energy irradiation-initiated grafting of glycidyl methacrylate

International Nuclear Information System (INIS)

Takacs, E.; Wojnarovits, L.; Borsa, J.

2011-01-01

Complete text of publication follows. Sustainable development needs renewable raw materials applied wherever possible. Cellulose is the most abundant biopolymer on earth; various modifications of its properties for special uses are important issues of the research. Some contaminations in wastewaters, e.g. pesticides, are hydrophobic materials; their adsorption on hydrophilic cellulose substrates is very limited. Cotton cellulose was grafted by glycidyl methacrylate in simultaneous grafting using gamma irradiation initiation. Water uptake of cellulose significantly decreased while adsorption of phenol and a pesticide molecule (2,4-dichlorophenoxyacetic acid: 2,4-D) increased upon grafting. As the figure shows on untreated sample even negative 2,4-D adsorption occurred, due to the selective adsorption of water from the solution; the adsorption did not approach its saturation value even in a 30 hours time period investigated. Saturation of phenol adsorption was achieved after 5-6 hours; adsorption equilibrium data of phenol fitted the Langmuir isotherm.

Trial of human laser epilation technology for permanent wool removal in Merino sheep.

Science.gov (United States)

Colditz, I G; Cox, T; Small, A H

2015-01-01

To assess whether human laser epilation technology can permanently prevent wool growth in sheep. An observational study. Two commercial human epilation lasers (Sharplan alexandrite 755 nm laser, and Lumenis LightSheer 800 nm diode laser) were tested at energies between 10 and 100 J/cm2 and pulse widths from 2 to 400 ms. Wool was clipped from flank, breech, pizzle and around the eyes of superfine Merino sheep with Oster clippers. After initial laser removal of residual wool to reveal bare skin, individual skin sites were treated with up to 15 cycles of laser irradiation. Behavioural responses during treatment, skin temperature immediately after treatment and skin and wool responses for 3 months after treatment were monitored. A clear transudate was evident on the skin surface within minutes. A dry superficial scab developed by 24 h and remained adherent for at least 6 weeks. When scabs were shed, there was evidence of scarring at sites receiving multiple treatment cycles and normal wool growth in unscarred skin. There was no evidence of laser energy level or pulse width affecting the response of skin and wool to treatment and no evidence of permanent inhibition of wool growth by laser treatment. Laser treatment was well tolerated by the sheep. Treatment of woolled skin with laser parameters that induce epilation by selective photothermolysis in humans failed to induce permanent inhibition of wool growth in sheep. Absence of melanin in wool may have contributed to the result. © 2015 Australian Veterinary Association.

Study of lithium insertion in hard carbon made from cotton wool

Science.gov (United States)

Peled, Emanuel; Eshkenazi, Victor; Rosenberg, Yuri

Hard-carbon materials were made either by one-step or multi-step pyrolysis of cotton cloth between 700 and 1100°C. All carbons have been characterized by gas sorption, X-ray diffraction (XRD) and small-angle X-ray scattering (SAXS) techniques. Two types of carbons have been obtained. One, made by multi-step pyrolysis, has the highest lithium reversible capacity [about 600 (mA h)/g] and two distinct voltage regions: a sloping one between 1.5 and about 0.1 V, called the high-voltage region (HVR), and a horizontal one between 0.1 and 0 V, called the low-voltage plateau (LVP). The other carbons made by the one-step process have only the HVR and less capacity [up to 470 (mA h)/g]. The influence of the current density and temperature on the capacity and degradation rate in both LVP and HVR was checked. We suggest that there are two different modes of lithium insertion: intercalation-like (on both sides of single graphene sheets) at lower potentials and chemical binding to edge carbon atoms at higher potentials vs. lithium reference electrode. A schematic model for lithiated carbon is proposed.

Fabrication and Characterization of Electrospun Wool Keratin/Poly(vinyl alcohol) Blend Nanofibers

OpenAIRE

Shuai Li; Xu-Hong Yang

2014-01-01

Wool keratin/poly(vinyl alcohol) (PVA) blend nanofibers were fabricated using the electrospinning method in formic acid solutions with different weight ratios of keratin to PVA. The resultant blend nanofibers were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), X-ray diffraction (XRD), thermal gravimetric analysis (TGA), and tensile test. SEM images showed that the diameter of the blend nanofibers was affected by the content of keratin in blend solution...

76 FR 72769 - National Emissions Standards for Hazardous Air Pollutants: Mineral Wool Production and Wool...

Science.gov (United States)

2011-11-25

.... \\4\\ Cement Kiln Recycling Coalition v. EPA, 255 F.3d 855 (DC Cir. 2001) (per curiam). \\5\\ National... insulation and bonded heavy- density products.'' The MACT rule for the Wool Fiberglass Manufacturing source...

The Assessment of Natural Pigmentation in Archaeological Wool

DEFF Research Database (Denmark)

Scharff, Annemette Bruselius

2018-01-01

Naturally coloured wool contains pigment grains that mainly occur as ellipsoidal organelles (eumelanin) or spher¬ical grains (pheomelanin). Eumelanin is the most commonly occurring pigment, but naturally coloured wool fi¬bres contain both eumelanin and pheomelanin. In black and brown wool....... This can especially be the case if the pigments are degraded. When analysing the textiles from Lønne Hede (a Danish Iron Age inhumation grave), it was difficult to gain exact information about the natural pigmentation in some of the samples. To investigate this further, four samples of red-brown yarns from...... patterned fragments were selected for analyses. Earlier dyestuff analyses of the red-brown yarns gave no results, and it was therefore necessary to test the yarns for natural pigmentation. Three different methods were used for the analy¬ses. Transmitted light microscopy of whole mounts of the fibres...

Characterising the potential of sheep wool for ancient DNA analyses

DEFF Research Database (Denmark)

Brandt, Luise Ørsted; Tranekjer, Lena D.; Mannering, Ulla

2011-01-01

can be PCR-amplified from wool derived from a variety of breeds, regardless of the body location or natural pigmentation. Furthermore, although DNA can be PCR-amplified from wool dyed with one of four common plant dyes (tansy, woad, madder, weld), the use of mordants such as alum or iron leads...... and content of DNA in hair shafts are known to vary, and it is possible that common treatments of wool such as dyeing may negatively impact the DNA. Using quantitative real-time polymerase chain reaction (PCR), we demonstrate that in general, short fragments of both mitochondrial and single-copy nuclear DNA...

Developing quality standards for physical properties of mineral wool plugs

NARCIS (Netherlands)

Blok, C.; Berg, van den C.C.; Winkel, van A.

2014-01-01

The KIWA certification guidelines for mineral wool products contain standards for slabs and blocks. Propagators would like to introduce quality standards for mineral wool plugs as well. Main concerns were effects of too dense plugs on plant growth, and handling problems with too fluffy or broken

Genetic relationship between wool shedding in ewe-lambs and ewes

Science.gov (United States)

Interest in reducing labor costs related to shearing has led to the development of breeds that naturally shed their wool annually. This goal has been achieved by introducing hair-sheep genetics. These developments are relatively recent and thus the genetic underpinnings of wool shedding (WS) are not...

Supercapacitor Electrode Based on Activated Carbon Wool Felt

Directory of Open Access Journals (Sweden)

Ana Claudia Pina

2018-04-01

Full Text Available An electrical double-layer capacitor (EDLC is based on the physical adsorption/desorption of electrolyte ions onto the surface of electrodes. Due to its high surface area and other properties, such as electrochemical stability and high electrical conductivity, carbon materials are the most widely used materials for EDLC electrodes. In this work, we study an activated carbon felt obtained from sheep wool felt (ACF’f as a supercapacitor electrode. The ACF’f was characterized by elemental analysis, scanning electron microscopy (SEM, textural analysis, and X-ray photoelectron spectroscopy (XPS. The electrochemical behaviour of the ACF’f was tested in a two-electrode Swagelok®-type, using acidic and basic aqueous electrolytes. At low current densities, the maximum specific capacitance determined from the charge-discharge curves were 163 F·g−1 and 152 F·g−1, in acidic and basic electrolytes, respectively. The capacitance retention at higher current densities was better in acidic electrolyte while, for both electrolytes, the voltammogram of the sample presents a typical capacitive behaviour, being in accordance with the electrochemical results.

Fabrication of superhydrophobic cotton fabrics using crosslinking polymerization method

Science.gov (United States)

Jiang, Bin; Chen, Zhenxing; Sun, Yongli; Yang, Huawei; Zhang, Hongjie; Dou, Haozhen; Zhang, Luhong

2018-05-01

With the aim of removing and recycling oil and organic solvent from water, a facile and low-cost crosslinking polymerization method was first applied on surface modification of cotton fabrics for water/oil separation. Micro-nano hierarchical rough structure was constructed by triethylenetetramine (TETA) and trimesoyl chloride (TMC) that formed a polymeric layer on the surface of the fabric and anchored Al2O3 nanoparticles firmly between the fabric surface and the polymer layer. Superhydrophobic property was further obtained through self-assembly grafting of hydrophobic groups on the rough surface. The as-prepared cotton fabric exhibited superoleophilicity in atmosphere and superhydrophobicity both in atmosphere and under oil with the water contact angle of 153° and 152° respectively. Water/oil separation test showed that the as-prepared cotton fabric can handle with various oil-water mixtures with a high separation efficiency over 99%. More importantly, the separation efficiency remained above 98% over 20 cycles of reusing without losing its superhydrophobicity which demonstrated excellent reusability in oil/water separation process. Moreover, the as-prepared cotton fabric possessed good contamination resistance ability and self-cleaning property. Simulation washing process test showed the superhydrophobic cotton fabric maintained high value of water contact angle above 150° after 100 times washing, indicating great stability and durability. In summary, this work provides a brand-new way to surface modification of cotton fabric and makes it a promising candidate material for oil/water separation.

Wool and grain dusts stimulate TNF secretion by alveolar macrophages in vitro.

Science.gov (United States)

Brown, D M; Donaldson, K

1996-06-01

The aim of the study was to investigate the ability of two organic dusts, wool and grain, and their soluble leachates to stimulate secretion of tumour necrosis factor (TNF) by rat alveolar macrophages with special reference to the role of lipopolysaccharide (LPS). Rat alveolar macrophages were isolated by bronchoalveolar lavage (BAL) and treated in vitro with whole dust, dust leachates, and a standard LPS preparation. TNF production was measured in supernatants with the L929 cell line bioassay. Both wool and grain dust samples were capable of stimulating TNF release from rat alveolar macrophages in a dose-dependent manner. The standard LPS preparation caused a dose-dependent secretion of TNF. Leachates prepared from the dusts contained LPS and also caused TNF release but leachable LPS could not account for the TNF release and it was clear that non-LPS leachable activity was present in the grain dust and that wool dust particles themselves were capable of causing release of TNF. The role of LPS in wool dust leachates was further investigated by treating peritoneal macrophages from two strains of mice, LPS responders (C3H) and LPS non-responders (C3H/HEJ), with LPS. The non-responder mouse macrophages produced very low concentrations of TNF in response to the wool dust leachates compared with the responders. LPS and other unidentified leachable substances present on the surface of grain dust, and to a lesser extent on wool dust, are a trigger for TNF release by lung macrophages. Wool dust particles themselves stimulate TNF. TNF release from macrophages could contribute to enhancement of inflammatory responses and symptoms of bronchitis and breathlessness in workers exposed to organic dusts such as wool and grain.

Development of Flame Resistant Combat Uniform Fabrics Made from Long Staple Wool and Aramid Blend Yarn

Science.gov (United States)

2013-04-15

Kentwool recombed the wool top ( wool is first combed during the production of wool top); a second combing process is an optional step sometimes used in...RESISTANT COMBAT UNIFORM FABRICS MADE FROM LONG STAPLE WOOL AND ARAMID BLEND YARN by Parvez Mehta* Mitchell Driggers* and Carole...SUBTITLE DEVELOPMENT OF FLAME RESISTANT COMBAT UNIFORM FABRICS MADE FROM LONG STAPLE WOOL AND ARAMID BLEND YARN 5a. CONTRACT NUMBER W911QY-11

Determination of Attributes in Cotton (Gossypium hirsutum L. Genotypes in Corn-Soybean Rotation Associated with Acid Amended Soils in the Colombian Eastern Plains

Directory of Open Access Journals (Sweden)

Luis Fernando Campuzano Duque

2015-07-01

Full Text Available For the last 15 years, Colombia has developed a research process leading to the expansion of its agricultural frontier at the flat well drained savannas of the Eastern Plains, by improving predominantly acid soils with liming to increase base saturation with depth, vertical liming —as its referred locally—, crop rotation with rice, corn, soybeans, and with the potential to include other crops like cotton in the rotation system. To achieve this, a pioneering research in Colombia was conducted to determine the adaptation of cotton in the acid conditions of the high plains improved sheets. An Agronomic evaluation test was developed using five elite genotypes of cotton in a design of a randomized complete block at four locations in soils with base saturation above 80 %. The results identified a genotype (LC-156, which presented an adaptation to the high plains, associated with an average yield of 2.2 t/ha of cottonseed, 1.5 t/ha of cotton fiber type medium-long, a percentage of fiber extraction above 36.0 %. The comparative advantage of this region for sustainable cotton production is given by the yield of cotton fiber —which ishigher than the national average—, to the 33.2 % reduction in production costs, the quality of long/medium-fiber destined for export and the absence of the pest insect of greatest economic impact in Colombia: the weevil (Anthonomus grandis Boheman.

Environmental-friendly wool fabric finishing by some water plant extracts

Directory of Open Access Journals (Sweden)

Šmelcerović Miodrag

2007-01-01

Full Text Available In this article, environmental-friendly finishing of wool fabric were processed with several water extract plants, such as hibiscus, St. John's wort, and marigold. The plant extracts have good basis in the commercial dyeing of wool, for garment and carpet industry. At the same time, the environmental-friendly finishing by water extracts plants shows very good fastness of the antimicrobial properties and coloration of wool fabric. From an ecological viewpoint, the substitution of chemical dyes with "natural products" may represent not only a strategy to reduce risk and pollutants but also an opportunity for new markets and new businesses, which can expend involving of ecology in trade policy.

Improved biotribological properties of PEEK by photo-induced graft polymerization of acrylic acid

Energy Technology Data Exchange (ETDEWEB)

Zhao, Xiaoduo; Xiong, Dangsheng, E-mail: xiongds@163.com; Wang, Kun; Wang, Nan

2017-06-01

The keys of biomaterials application in artificial joints are good hydrophilicity and wear resistance. One kind of the potential bio-implant materials is polyetheretherketone (PEEK), which has some excellent properties such as non-toxic and good biocompatibility. However, its bioinert surface and inherent chemical inertness hinder its application. In this study, we reported an efficient method for improving the surface wettability and wear resistance for PEEK, a layer of acrylic acid (AA) polymer brushes on PEEK surface was prepared by UV-initiated graft polymerization. The effects of different grafting parameters (UV-irradiation time/AA monomer solution concentration) on surface characteristics were clearly investigated, and the AA-g-PEEK specimens were examined by ATR-FTIR, static water contact angle measurements and friction tests. Our results reveal that AA can be successfully grafted onto the PEEK surface after UV irradiation, the water wettability and tribological properties of AA-g-PEEK are much better than untreated PEEK because that AA is a hydrophilic monomer, the AA layer on PEEK surface can improve its bearing capacity and reduce abrasion. This detailed understanding of the grafting parameters allows us to accurately control the experimental products, and this method of surface modification broadens the use of PEEK in orthopedic implants. - Highlights: • Acrylic acid was successful grafted onto PEEK substrate by UV-initiated graft polymerization. • AA-g-PEEK owned better hydrophilicity than untreated PEEK. • Wear resistance of AA-g-PEEK were significantly improved due to AA brushes could bear high contact stress.

Fiber-Content Measurement of Wool-Cashmere Blends Using Near-Infrared Spectroscopy.

Science.gov (United States)

Zhou, Jinfeng; Wang, Rongwu; Wu, Xiongying; Xu, Bugao

2017-10-01

Cashmere and wool are two protein fibers with analogous geometrical attributes, but distinct physical properties. Due to its scarcity and unique features, cashmere is a much more expensive fiber than wool. In the textile production, cashmere is often intentionally blended with fine wool in order to reduce the material cost. To identify the fiber contents of a wool-cashmere blend is important to quality control and product classification. The goal of this study is to develop a reliable method for estimating fiber contents in wool-cashmere blends based on near-infrared (NIR) spectroscopy. In this study, we prepared two sets of cashmere-wool blends by using either whole fibers or fiber snippets in 11 different blend ratios of the two fibers and collected the NIR spectra of all the 22 samples. Of the 11 samples in each set, six were used as a subset for calibration and five as a subset for validation. By referencing the NIR band assignment to chemical bonds in protein, we identified six characteristic wavelength bands where the NIR absorbance powers of the two fibers were significantly different. We then performed the chemometric analysis with two multilinear regression (MLR) equations to predict the cashmere content (CC) in a blended sample. The experiment with these samples demonstrated that the predicted CCs from the MLR models were consistent with the CCs given in the preparations of the two sample sets (whole fiber or snippet), and the errors of the predicted CCs could be limited to 0.5% if the testing was performed over at least 25 locations. The MLR models seem to be reliable and accurate enough for estimating the cashmere content in a wool-cashmere blend and have potential to be used for tackling the cashmere adulteration problem.

New method to determine wools and hairs degradation

OpenAIRE

Marsal Amenós, Félix

2013-01-01

A new method is proposed, validated in the industrial practice, to determine possible bacterial and microbial degradation in textile wools and hairs. It is applied to wools of variable fineness between 18 and 34 microns and to alpaca fibers between 20 and 36 microns. It is based on a dynamometer test to determine tribocharge excision the slivers combed. The rheological behavior of degraded fiber slivers is quite different in the spinning process in addition to the major problems that appear i...

Flame retardant finishing of cotton fabric based on synergistic compounds containing boron and nitrogen.

Science.gov (United States)

Xie, Kongliang; Gao, Aiqin; Zhang, Yongsheng

2013-10-15

Boric acid and compound containing nitrogen, 2,4,6-tri[(2-hydroxy-3-trimethyl-ammonium)propyl]-1,3,5-triazine chloride (Tri-HTAC) were used to finish cotton fabric. The flame retardant properties of the finished cotton fabrics and the synergetic effects of boron and nitrogen elements were investigated and evaluated by limited oxygen index (LOI) method. The mechanism of cross-linking reaction among cotton fiber, Tri-HTAC, and boric acid was discussed by FTIR and element analysis. The thermal stability and surface morphology of the finished cotton fabrics were investigated by thermogravimetric analysis (TGA) and scanning electron microscope (SEM), respectively. The finishing system of the mixture containing boron and nitrogen showed excellent synergistic flame retardancy for cotton fabric. The cotton fabric finished with mixture system had excellent flame retardancy. The LOI value of the treated cotton fabric increased over 27.5. Tri-HTAC could form covalent bonds with cellulose fiber and boric acid. The flame retardant cotton fabric showed a slight decrease in tensile strength and whiteness. The surface morphology of flame retardant cotton fiber was smooth. Copyright © 2013 Elsevier Ltd. All rights reserved.

Chemical modification of chitosan film via surface grafting of citric acid molecular to promote the biomineralization

Energy Technology Data Exchange (ETDEWEB)

Liu, Yang, E-mail: liuyang@cczu.edu.cn [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou 213164 (China); Engineering Research Center of Nano-Geo Materials of Ministry of Education, China University of Geosciences, Wuhan 430074 (China); School of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China); Shen, Xin; Zhou, Huan [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou 213164 (China); Wang, Yingjun [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China); Deng, Linhong, E-mail: dlh@cczu.edu.cn [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou 213164 (China)

2016-05-01

Graphical abstract: - Highlights: • Chitosan film was modified by surface grafting of citric acid. • The modified film has good hydrophilicity and moisture-retaining capacity. • The citric acid grafting treatment significantly promote the biomineralization. • MC3T3-E1 osteoblasts research confirms the biocompatibility of the film. - Abstract: We develop a novel chitosan–citric acid film (abbreviated as CS–CA) suitable for biomedical applications in this study. In this CS–CA film, the citric acid, which is a harmless organic acid has been extensively investigated as a modifying agent on carbohydrate polymers, was cross-linked by 1-Ethyl-3-(3-dimethyl aminopropyl) carbodiimide (EDC) and N-hydroxysuccinimide (NHS) onto the surface of chitosan (CS) film. Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) confirms the graft copolymerization of the modified chitosan film (CS–CA). Surface wettability, moisturizing performance, the capacity of mineralization in vitro and biocompatibility of the films were characterized. After modification, this CS–CA film has good hydrophilicity. It is very evident that the citric acid grafting treatment significantly promotes the biomineralization of the chitosan based substrates. Cell experiments show that the MC3T3-E1 osteoblasts can adhere and proliferate well on the surface of CS–CA film. This CS–CA film, which can be prepared in large quantities and at low cost, should have potential application in bone tissue engineering.

Fabrication of Durably Superhydrophobic Cotton Fabrics by Atmospheric Pressure Plasma Treatment with a Siloxane Precursor

Directory of Open Access Journals (Sweden)

Jing Yang

2018-04-01

Full Text Available The surface treatment of fabrics in an atmospheric environment may pave the way for commercially viable plasma modifications of fibrous matters. In this paper, we demonstrate a durably superhydrophobic cotton cellulose fabric prepared in a single-step graft polymerization of hexamethyldisiloxane (HMDSO by N2 and O2 atmospheric pressure plasma. We systematically investigated effects on contact angle (CA and surface morphology of the cotton fabric under three operational parameters: precursor value; ionization gas flow rate; and plasma cycle time. Surface morphology, element composition, chemical structure and hydrophobic properties of the treated fabric were characterized by scanning electron microscope (SEM, EDS, FTIR and CA on the fabrics. The results indicated that a layer of thin film and nano-particles were evenly deposited on the cotton fibers, and graft polymerization occurred between cellulose and HMDSO. The fabric treated by O2 plasma exhibited a higher CA of 162° than that treated by N2 plasma which was about 149°. Furthermore, the CA of treated fabrics decreased only 0°~10° after storing at the ambient conditions for four months, and treated fabrics could also endure the standard textile laundering procedure in AATCC 61-2006 with minimum change. Therefore, this single-step plasma treatment method is shown to be a novel and environment-friendly way to make durable and superhydrophobic cotton fabrics.

The effects of fabric for sleepwear and bedding on sleep at ambient temperatures of 17°C and 22°C

Directory of Open Access Journals (Sweden)

Shin M

2016-04-01

Full Text Available Mirim Shin,1 Mark Halaki,1 Paul Swan,2 Angus Ireland,2 Chin Moi Chow1 1Exercise, Health and Performance Research Group, Faculty of Health Sciences, The University of Sydney, Lidcombe, 2Australian Wool Innovation Limited, The Woolmark Company, Sydney, NSW, Australia Abstract: The fibers used in clothing and bedding have different thermal properties. This study aimed to investigate the influences of textile fabrics on sleep under different ambient temperature (Ta conditions. Seventeen healthy young participants (ten males underwent nine nights of polysomnography testing including an adaptation night. Participants were randomized to each of the three binary factors: sleepwear (cotton vs wool, bedding (polyester vs wool, and Ta (17°C vs 22°C with relative humidity set at 60%. Skin temperature (Tsk and core temperature (Tc were monitored throughout the sleep period. Sleep onset latency (SOL was significantly shortened when sleeping in wool with trends of increased total sleep time and sleep efficiency compared to cotton sleepwear. At 17°C, the proportion of sleep stages 1 (%N1 and 3 (%N3 and rapid eye movement sleep was higher, but %N2 was lower than at 22°C. Interaction effects (sleepwear × Ta showed a significantly shorter SOL for wool than cotton at 17°C but lower %N3 for wool than cotton at 22°C. A significantly lower %N2 but higher %N3 was observed for wool at 17°C than at 22°C. There was no bedding effect on sleep. Several temperature variables predicted the sleep findings in a stepwise multiple regression analysis and explained 67.8% of the variance in SOL and to a lesser degree the %N2 and %N3. These findings suggest that sleepwear played a contributory role to sleep outcomes and participants slept better at 17°C than at 22°C.Keywords: cotton, polyester, wool, polysomnography, skin temperature, core body temperature

Expression Profiling Reveals Genes Involved in the Regulation of Wool Follicle Bulb Regression and Regeneration in Sheep

Directory of Open Access Journals (Sweden)

Guangbin Liu

2015-04-01

Full Text Available Wool is an important material in textile manufacturing. In order to investigate the intrinsic factors that regulate wool follicle cycling and wool fiber properties, Illumina sequencing was performed on wool follicle bulb samples from the middle anagen, catagen and late telogen/early anagen phases. In total, 13,898 genes were identified. KRTs and KRTAPs are the most highly expressed gene families in wool follicle bulb. In addition, 438 and 203 genes were identified to be differentially expressed in wool follicle bulb samples from the middle anagen phase compared to the catagen phase and the samples from the catagen phase compared to the late telogen/early anagen phase, respectively. Finally, our data revealed that two groups of genes presenting distinct expression patterns during the phase transformation may have important roles for wool follicle bulb regression and regeneration. In conclusion, our results demonstrated the gene expression patterns in the wool follicle bulb and add new data towards an understanding of the mechanisms involved in wool fiber growth in sheep.

Inhibition of Listeria monocytogenes in Fresh Cheese Using Chitosan-Grafted Lactic Acid Packaging

Directory of Open Access Journals (Sweden)

Laura N. Sandoval

2016-04-01

Full Text Available A chitosan from biologically obtained chitin was successfully grafted with d,l-lactic acid (LA in aqueous media using p-toluenesulfonic acid as catalyst to obtain a non-toxic, biodegradable packaging material that was characterized using scanning electron microscopy, water vapor permeability, and relative humidity (RH losses. Additionally, the grafting in chitosan with LA produced films with improved mechanical properties. This material successfully extended the shelf life of fresh cheese and inhibited the growth of Listeria monocytogenes during 14 days at 4 °C and 22% RH, whereby inoculated samples with chitosan-g-LA packaging presented full bacterial inhibition. The results were compared to control samples and commercial low-density polyethylene packaging.

Improved microstructure of cement-based composites through the addition of rock wool particles

Energy Technology Data Exchange (ETDEWEB)

Lin, Wei-Ting [Dept. of Civil Engineering, National Ilan University, Ilan 26047, Taiwan (China); Institute of Nuclear Energy Research, Atomic Energy Council, Taoyuan 32546, Taiwan (China); Cheng, An, E-mail: ancheng@niu.edu.tw [Dept. of Civil Engineering, National Ilan University, Ilan 26047, Taiwan (China); Huang, Ran; Zou, Si-Yu [Dept. of Harbor and River Engineering, National Taiwan Ocean University, Keelung 20224, Taiwan (China)

2013-10-15

Rock wool is an inorganic fibrous substance produced by steam blasting and cooling molten glass. As with other industrial by-products, rock wool particles can be used as cementitious materials or ultra fine fillers in cement-based composites. This study investigated the microstructure of mortar specimens produced with cement-based composites that include various forms of rock wool particles. It conducted compressive strength testing, rapid chloride penetration tests, X-ray diffraction analysis, thermo-gravimetric analysis, and scanning electronic microscopy to evaluate the macro- and micro-properties of the cement-based composites. Test results indicate that inclusion of rock wool particles in composites improved compressive strength and reduced chloride ion penetration at the age of 91 days due to the reduction of calcium hydroxide content. Microscopic analysis confirms that the use of rock wool particles contributed to the formation of a denser, more compact microstructure within the hardened paste. In addition, X-ray diffraction analysis shows few changes in formation of pozzolanic reaction products and no new hydrations are formed with incorporating rock wool particles. - Highlights: • We report the microstructural characterization of cement-based composites. • Different mixes produced with various rock wool particles have been tested. • The influence of different mixes on macro and micro properties has been discussed. • The macro properties are included compressive strength and permeability. • XRD and SEM observations confirm the pozzolanic reaction in the resulting pastes.

The analysis and comparison of blue wool fibre populations found at random on clothing.

Science.gov (United States)

Wiggins, K; Drummond, P

2005-01-01

Fifty-eight garments were taped and searched for mid to dark blue wool fibres. These were then removed from the tapings, mounted on slides and examined using a high-power microscope (400x). A total of 2,740 blue wool fibres were identified and visible range microspectrophotometry (MSP) was performed on them. Three hundred independent blue wool populations were identified on 56 of the 58 garments searched. The lack of control fibres meant the spectral range of each population was unknown. The number of populations may have been underestimated by grouping together the fibres that had broad single peaks and a lack of distinguishing features in the spectra. Although blue wool is considered to be a common fibre type, 300 unique spectral shapes were identified by the use of microspectrophotometry alone. This demonstrates that the dyes used in the dyeing of blue wool are variable. Showing that many different populations of blue wool occur on a range of garments should ensure that the forensic scientist does not underestimate or understate the strength of evidence in cases where blue wool is found. Hopefully this work will enlighten scientists and enable them to also assess the true value of their findings when other commonly occurring fibres are encountered.

Effect of l-lysine-assisted surface grafting for nano-hydroxyapatite on mechanical properties and in vitro bioactivity of poly(lactic acid-co-glycolic acid).

Science.gov (United States)

Liuyun, Jiang; Lixin, Jiang; Chengdong, Xiong; Lijuan, Xu; Ye, Li

2016-01-01

It is promising and challenging to study surface modification for nano-hydroxyapatite to improve the dispersion and enhance the mechanical properties and bioactivity of poly(lactic acid-co-glycolic acid). In this paper, we designed an effective new surface grafting with the assist of l-lysine for nano-hydroxyapatite, and the nano-hydroxyapatite surface grafted with the assist of l-lysine (g-nano-hydroxyapatite) was incorporated into poly(lactic acid-co-glycolic acid) to develop a series of g-nano-hydroxyapatite/poly(lactic acid-co-glycolic acid) nano-composites. The surface modification reaction for nano-hydroxyapatite, the mechanical properties, and in vitro human osteoblast-like cell (MG-63) response were characterized and investigated by Fourier transformation infrared, thermal gravimetric analysis, dispersion test, electromechanical universal tester, differential scanning calorimeter measurements, and in vitro cells culture experiment. The results showed that the grafting amount on the surface of nano-hydroxyapatite was enhanced with the increase of l-lysine, and the dispersion of nano-hydroxyapatite was improved more, so that it brought about better promotion crystallization and more excellent mechanical enhancement effect for poly(lactic acid-co-glycolic acid), comparing with the unmodified nano-hydroxyapatite. Moreover, the cells' attachment and proliferation results confirmed that the incorporation of the g-nano-hydroxyapatite into poly(lactic acid-co-glycolic acid) exhibited better biocompatibility than poly(lactic acid-co-glycolic acid). The above results indicated that the new surface grafting with the assist of l-lysine for nano-hydroxyapatite was an ideal novel surface modification method, which brought about better mechanical enhancement effect and in vitro bioactivity for poly(lactic acid-co-glycolic acid) with adding higher g-nano-hydroxyapatite content, suggesting it had a great potential to be used as bone fracture internal fixation materials

Negotiating climate change agreements - the view from the mineral wool sector

International Nuclear Information System (INIS)

Loudon, Robert

2001-01-01

Trade associations representing energy-intensive industrial sectors in the UK have negotiated agreements with the Department of the Environment, Transport and the Regions (DETR) to enable their members to receive an 80% rebate on the climate change levy (CCL) providing they meet agreed energy saving targets. Insulation manufacturing is represented by Eurisol and the Mineral Wool Energy Savings Company (MINESCO). Rock wool and glass wool manufacture uses energy for blending, melting, fiberising, curing, cooling, cutting and packaging. However the mineral wool sector has already made significant improvements in energy efficiency over the last 20 years. Confidentiality issues led to Eurisol appointing consultants to advise on how individual plants could achieve further energy savings. Cadogan Consultants developed a strategy that incorporated both qualitative and quantitative issues and allowed the energy saving potential at each site to be identified. MINESCO agreed energy saving targets with the DETR in December 2000, but much work remains to be done

Thermosensitive membranes by radiation-induced graft polymerization of N-isopropyl acrylamide/acrylic acid on polypropylene nonwoven fabric

International Nuclear Information System (INIS)

Ikram, Saiqa; Kumari, Mamta; Gupta, Bhuvanesh

2011-01-01

Radiation-induced graft copolymerization of N-isopropylacrylamide (NIPAAm) and acrylic acid (AA) mixture was investigated on polypropylene nonwoven fabric to develop a thermosensitive material. The grafting was carried out using methanol, acetone and butanone as homopolymerization inhibitor in the reaction medium. Butanone was observed to give the maximum grafting. It was observed that the grafting is significantly influenced by the reaction conditions, such as radiation dose, monomer concentration, monomer ratio, solvent composition and reaction temperature. The degree of grafting increased as the AA and NIPAAm concentration in the reaction medium increased. The degree of grafting increased as the AA fraction in the NIPAAm/AA mixture increased. The temperature dependence of the grafting process is very much governed by the thermosensitive nature of the grafted chains right from the stage when initial grafting has taken place.

Thermosensitive membranes by radiation-induced graft polymerization of N-isopropyl acrylamide/acrylic acid on polypropylene nonwoven fabric

Energy Technology Data Exchange (ETDEWEB)

Ikram, Saiqa; Kumari, Mamta [Department of Chemistry, Jamia Millia Islamia (Central University), New Delhi-110025 (India); Gupta, Bhuvanesh, E-mail: bgupta@textile.iitd.ernet.i [Department of Textile Technology, Indian Institute of Technology, New Delhi-110016 (India)

2011-01-15

Radiation-induced graft copolymerization of N-isopropylacrylamide (NIPAAm) and acrylic acid (AA) mixture was investigated on polypropylene nonwoven fabric to develop a thermosensitive material. The grafting was carried out using methanol, acetone and butanone as homopolymerization inhibitor in the reaction medium. Butanone was observed to give the maximum grafting. It was observed that the grafting is significantly influenced by the reaction conditions, such as radiation dose, monomer concentration, monomer ratio, solvent composition and reaction temperature. The degree of grafting increased as the AA and NIPAAm concentration in the reaction medium increased. The degree of grafting increased as the AA fraction in the NIPAAm/AA mixture increased. The temperature dependence of the grafting process is very much governed by the thermosensitive nature of the grafted chains right from the stage when initial grafting has taken place.

Determining the degree of grafting for poly (vinylidene fluoride) graft-copolymers using fluorine elemental analysis

International Nuclear Information System (INIS)

Yu Yang; Zhang Bowu; Yang Xuanxuan; Deng Bo; Li Linfan; Yu Ming; Li Jingye

2011-01-01

Acrylic acid (AAc) and styrene (St) were grafted onto poly (vinylidene fluoride) (PVDF) powder or membrane samples by pre-irradiation graft copolymerization. The grafted chains were proved by FT-IR spectroscopy analysis. The degree of grafting (DG) of the grafted PVDF was determined by fluorine elemental analysis (FEA) method, and was compared with the DGs determined by weighing method, acid-base back titration method and quantitative FT-IR method. The results show that the FEA method is accurate, convenient and universal, especially for the grafted polymer powders. (authors)

Processing and Properties of PCL/Cotton Linter Compounds

OpenAIRE

Bezerra,Elieber Barros; França,Danyelle Campos; Morais,Dayanne Diniz de Souza; Rosa,Morsyleide de Freitas; Morais,João Paulo Saraiva; Araújo,Edcleide Maria; Wellen,Renate Maria Ramos

2017-01-01

Biodegradable compounds of poly(ε-caprolactone) (PCL)/ cotton linter were melting mixed with filling content ranging from 1% to 5% w/w. Cotton linter is an important byproduct of textile industry; in this work it was used in raw state and after acid hydrolysis. According to the results of torque rheometry no decaying of viscosity took place during compounding, evidencing absence of breaking down in molecular weight. The thermal stability increased by 20% as observed in HDT for PCL/cotton...

Processing and properties of PCL/cotton linter compounds

Energy Technology Data Exchange (ETDEWEB)

Bezerra, Elieber Barros; Franca, Danyelle Campos; Morais, Dayanne Diniz de Souza; Araujo, Edcleide Maria [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia de Materiais; Rosa, Morsyleide de Freitas; Morais, Joao Paulo Saraiva [Embrapa Tropical Agroindustia, Fortaleza, CE (Brazil); Wellen, Renate Maria Ramos, E-mail: wellen.renate@gmail.com [Universidade Federal da Paraiaba (UFPB), Joao Pessoa, PB (Brazil)

2017-03-15

Biodegradable compounds of poly(ε-caprolactone) (PCL)/ cotton linter were melting mixed with filling content ranging from 1% to 5% w/w. Cotton linter is an important byproduct of textile industry; in this work it was used in raw state and after acid hydrolysis. According to the results of torque rheometry no decaying of viscosity took place during compounding, evidencing absence of breaking down in molecular weight. The thermal stability increased by 20% as observed in HDT for PCL/cotton nanolinter compounds. Adding cotton linter to PCL did not change its crystalline character as showed by XRD; however an increase in degree of crystallinity was observed by means of DSC. From mechanical tests in tension was observed an increase in ductility of PCL, and from mechanical tests in flexion an increase in elastic modulus upon addition of cotton linter, whereas impact strength presented lower values for PCL/cotton linter and PCL/cotton nanolinter compounds. SEM images showed that PCL presents plastic fracture and cotton linter has an interlacing fibril structure with high L/D ratio, which are in agreement with matrix/fibril morphology observed for PCL/cotton linter compounds. PCL/cotton linter compounds made in this work cost less than neat PCL matrix and presented improved properties making feasible its commercial use. (author)

IMPROVING THE EFFICIENCY OF MINERAL WOOL SLABS TECHNOLOGY

Directory of Open Access Journals (Sweden)

Perfilov Vladimir Aleksandrovich

2016-03-01

Full Text Available The use of thermal insulation materials is an effective method to create an insulating envelope of a building, as well as to reduce energy costs and increase the durability of building structures. The properties of stone wool products and their operational durability is largely determined by the conditions of formation of the mineral wool carpet, uniform distribution of binder and its curing and the heat treatment conditions. Most domestic technologies are aimed at the production of mineral wool products with volume-oriented structure, which is formed using special units: spreader and corrugator placed in a production line. The next step to obtain the optimum structures is the production of dual density slabs. The denser upper layer receives mechanical loads caused by the operating conditions; the lower, less dense, but more thick layer performs the main function - insulation. The dual density slabs are produced on standard lines supplemented with a special unit, which is located in front of the heat treatment camera. Optimization of heat treatment parameters and prediction of the properties of materials is performed using software package.

Synthesis and Properties of Carbon Nanotube-Grafted Silica Nanoarchitecture-Reinforced Poly(Lactic Acid

Directory of Open Access Journals (Sweden)

Yao-Wen Hsu

2017-07-01

Full Text Available A novel nanoarchitecture-reinforced poly(lactic acid (PLA nanocomposite was prepared using multi-walled carbon nanotube (MWCNT-grafted silica nanohybrids as reinforcements. MWCNT-grafted silica nanohybrids were synthesized by the generation of silica nanoparticles on the MWCNT surface through the sol-gel technique. This synthetic method involves organo-modified MWCNTs that are dispersed in tetrahydrofuran, which incorporates tetraethoxysilane that undergoes an ultrasonic sol-gel process. Gelation yielded highly dispersed silica on the organo-modified MWCNTs. The structure and properties of the nanohybrids were established using 29Si nuclear magnetic resonance, Raman spectroscopy, wide-angle X-ray diffraction, thermogravimetric analysis, and transmission electron microscopy. The resulting MWCNT nanoarchitectures were covalently assembled into silica nanoparticles, which exhibited specific and controllable morphologies and were used to reinforce biodegradable PLA. The tensile strength and the heat deflection temperature (HDT of the PLA/MWCNT-grafted silica nanocomposites increased when the MWCNT-grafted silica was applied to the PLA matrix; by contrast, the surface resistivity of the PLA/MWCNT-grafted silica nanocomposites appeared to decline as the amount of MWCNT-grafted silica in the PLA matrix increased. Overall, the reinforcement of PLA using MWCNT-grafted silica nanoarchitectures was efficient and improved its mechanical properties, heat resistance, and electrical resistivity.

Effect of Surface Treatment on the Properties of Wool Fabric

Science.gov (United States)

Kan, C. W.; Yuen, C. W. M.; Chan, C. K.; Lau, M. P.

Wool fiber is commonly used in textile industry, however, it has some technical problems which affect the quality and performance of the finished products such as felting shrinkage, handle, lustre, pilling, and dyeability. These problems may be attributed mainly in the presence of wool scales on the fiber surface. Recently, chemical treatments such as oxidation and reduction are the commonly used descaling methods in the industry. However, as a result of the pollution caused by various chemical treatments, physical treatment such as low temperature plasma (LTP) treatment has been introduced recently because it is similarly capable of achieving a comparable descaling effect. Most of the discussions on the applications of LTP treatment on wool fiber were focused on applying this technique for improving the surface wettability and shrink resistance. Meanwhile, little discussion has been made on the mechanical properties, thermal properties, and the air permeability. In this paper, wool fabric was treated with LTP treatment with the use of a non-polymerizing gas, namely oxygen. After the LTP treatment, the fabrics low-stress mechanical properties, air permeability, and thermal properties were evaluated and discussed.

THE USE OF CHLOROSULFONIC ACID ON SULFONATION OF cPTFE FILM GRAFTED STYRENE FOR PROTON EXCHANGE MEMBRANE

Directory of Open Access Journals (Sweden)

Yohan Yohan

2010-06-01

Full Text Available Sulfonation of g-ray iradiated and styrene-grafted crosslinked polytetrafluoro ethylene film (cPTFE-g-S film have been done. The aim of the research was to make hydrophyl membrane as proton exchange membrane fuel cell. Sulfonation was prepared by using chlorosulfonic acid in chloroethane under various conditions. The impact of the percentage of grafting, the concentration of chlorosulfonic acid, the reaction time,and the reaction temperature on the properties of sulfonated film were examined. The results show that sulfonation of surface-grafted films was incomplete at room temperature. Increasing concentration of chlorosulfonic acid and reaction temperature accelerate the reaction but they also favor side reactions. These lead to the decrease of the ion-exchange capacity, water uptake, and proton conductivity but the increase of the resistance to oxidation in a perhydrol solution. The resulted cPTFE-g-SS membraneis stabile in a H2O2 30% solution for 20 h.   Keywords: Chorosulfonic acid, sulfonation, PTFE film, proton excange membrane.

Developmental and hormonal regulation of fiber quality in two natural-colored cotton cultivars

Institute of Scientific and Technical Information of China (English)

ZHANG Xiang; HU Da-peng; LI Yuan; CHEN Yuan; Eltayib H.M.A.Abidallha; DONG Zhao-di; CHEN De-hua; ZHANG Lei

2017-01-01

Cotton cultivars with brown (Xiangcaimian 2),green (Wanmian 39) and white (Sumian 9) fiber were investigated to study fiber developmental characteristics of natural-colored cotton and the effect of hormones on fiber quality at different stages after anthesis.Fiber lengths of both natural-colored cottons were lower than the white-fibered control,with brown-flbered cotton longer than green.Fiber strength,micronaire and maturation of natural-colored cotton were also lower than the control.The shorter fiber of the green cultivar was due to slower growth during 10 to 30 days post-anthesis (DPA).Likewise,the lower fiber strength,micronaire and maturation of natured-colored cotton were also due to slower growth during this pivotal stage.Indole-3-acetic acid (IAA) content at 10 DPA,and abscisic acid (ABA) content at 30 to 40 DPA were lower in the fibers of the natural-colored than that of the white-flbered cotton.After applying 20 mg L-1 gibberellic acid (GA3),the IAA content at 20 DPA in the brown and green-fibered cottons increased by 51.07 and 64.33％,fiber ABA content increased by 38.96 and 24.40％,and fiber length increased by 8.13 and 13.96％,respectively.Fiber strength,micronaire and maturation were also enhanced at boll opening stage.Those results suggest that the level of endogenous hormones affect fiber quality.Application of external hormones can increase hormone content in natural-colored cotton fiber,improving its quality.

Non-enzymatic depolymerization of cotton cellulose by fungal mimicking metabolites

DEFF Research Database (Denmark)

Hastrup, Anne Christine Steenkjær; Howell, Caitlin; Jensen, Bo

2011-01-01

peroxide, iron, and oxalic acid. The former two are involved in the Fenton reaction in which they react to form hydroxyl radicals, which cause an accelerated depolymerization in cotton cellulose. We found the same reaction to be caused by both iron Fe3+ and Fe2+. A 10 mM oxalic acid solution showed...... significant depolymerization effect on cotton cellulose. An oxalic acid/sodium oxalate buffered pH gradient had an inhibitory effect on the reduction of cellulose polymers at increased pH values. The organic iron chelator, EDTA, was found to promote depolymerization of cellulose in combination with Fenton......’s reagents, but inhibited the effect of oxalic acid in the absence of iron and hydrogen peroxide. Manganese was tested to see if metals other than iron could generate a significant impact on the degree of polymerization (DP) in cotton cellulose. Depolymerizing properties comparable to iron were seen...

Acrylic acid grafted PDMS preliminary activated by Ar{sup +}beam plasma and cell observation

Energy Technology Data Exchange (ETDEWEB)

Kostadinova, A.; Zaekov, N. [Institute of Biophysics, BAS, Sofia (Bulgaria); Keranov, I. [Department of Polymer Engineering, University of Chemical Technology and Metallurgy (UCTM), Sofia (Bulgaria)

2007-07-01

Plasma based Ar{sup +} beam performed in RF (13.56 MHz) low-pressure (200 mTorr) glow discharge (at 100 W, 1200 W and 2500 W) with a serial capacitance was employed for surface modification of poly(dimethylsiloxane) (PDMS) aimed at improvement of its interactions with living cells. The presence of a serial capacitance ensures arise of an ion-flow inside the plasma volume directed toward the treated sample and the vary of the discharge power ensures varied density of the ion-flow The initial adhesion of human fibroblast cells was studied on the described above plasma based Ar{sup +}beam modified and acrylic acid (AA) grafted or not fibronectin (FN) pre-coated or ba resurfaces. The cell response seem sto be related with the peculiar structure and wettability of the modified PDMS surface layer after plasma based Ar{sup +} beam treatment followed or not by AA grafting. Key words: Biomaterials; Surface treatment of PDMS; Plasma based Ar{sup +} beam; Acrylic acid grafting; Fibroblast cells.

Grafting of acrylic acid on etched latent tracks induced by swift heavy ions on polypropylene films

International Nuclear Information System (INIS)

Mazzei, R.; Fernandez, A.; Garcia Bermudez, G.; Torres, A.; Gutierrez, M.C.; Magni, M.; Celma, G.; Tadey, D.

2008-01-01

In order to continue with a systematic study that include different polymers and monomers, the residual active sites produced by heavy ion beams, that remain after the etching process, were used to start the grafting process. To produce tracks, foils of polypropylene (PP) were irradiated with 208 Pb of 25.62 MeV/n. Then, these were etched and grafted with acrylic acid (AA) monomers. Experimental curves of grafting yield as a function of grafting time with the etching time as a parameter were measured. Also, the grating yield as a function of the fluence and etching time was obtained. In addition, the permeation of solutions, with different pH, through PP grafted foils was measured

The effect of nutritional stress on the wool production potential of ...

African Journals Online (AJOL)

Forty fine wool and 40 strong wool weaner lambs were divided into two equal groups (treatment and control group) each. The treatment and control groups received diets of low and high nutritional value, respectively, for a period of three months. Thereafter the animals were kept for a further 18 months on natural pasture in ...

Studies on Dyeing Performance of Novel Acid Azo Dyes and Mordent Acid Azo Dyes Based on 2,4-Dihydroxybenzophenone

Directory of Open Access Journals (Sweden)

Bharat C. Dixit

2009-01-01

Full Text Available Novel acid azo and mordent acid azo dyes have been prepared by the coupling of diazo solution of different aminonaphthol sulphonic acids and aromatic amino acids with 2,4-dihydroxybenzophenone. The resultant dyes were characterized by elemental analysis as well as IR and 1H NMR spectral studies. The UV-visible spectral data have also been discussed in terms of structure property relationship. The dyeing assessments of all the dyes were evaluated on wool and silk textile fibers. The dyeing of chrome pretreated wool and silk have also been monitored. The result shows that better hue was obtained on mordented fiber. Results of bactericidal studies of chrome pretreated fibers revealed that the toxicity of mordented dyes against bacteria is fairly good. Dyeing on wool and silk fibers resulted in yellowish pink to reddish brown colourations having excellent light fastness and washing fastness.

Gene cloning: exploring cotton functional genomics and genetic improvement

Institute of Scientific and Technical Information of China (English)

Diqiu LIU; Xianlong ZHANG

2008-01-01

Cotton is the most important natural fiber plant in the world. The genetic improvement of the quality of the cotton fiber and agricultural productivity is imperative under the situation of increasing consumption and rapid development of textile technology. Recently, the study of cotton molecular biology has progressed greatly. A lot of specifically or preferentially expressed cotton fiber genes were cloned and analyzed. On the other hand, identification of stress response genes expressed in cotton was performed by other research groups. The major stress factors were studied including the wilt pathogens Verticillium dahliae, Fusarium oxy-sporum f. sp. vasinfectum, bacterial blight, root-knot nematode, drought, and salt stress. What is more, a few genes related to the biosynthesis of gossypol, other sesquiterpene phytoalexins and the major seed oil fatty acids were isolated from cotton. In the present review, we focused on the major advances in cotton gene cloning and expression profiling in the recent years.

Hierarchy of wool fibers and its interpretation using E-infinity theory

International Nuclear Information System (INIS)

He Jihuan; Ren Zhongfu; Fan Jie; Xu Lan

2009-01-01

Why do wool fibers show excellent advantages in warmth-retaining and many other practical properties? The paper concludes that their hierarchical structure is the key. Using E-infinity theory, its Hausdorff dimension is estimated to be about 4.2325, very close to El Naschie's E-infinity dimension, 4.2360, revealing an optimal structure for wool fibers.

Molecular and Biochemical Characterization of Cotton Epicuticular Wax in Defense Against Cotton Leaf Curl Disease.

Science.gov (United States)

Khan, Muhammad Azmat Ullah; Shahid, Ahmad Ali; Rao, Abdul Qayyum; Bajwa, Kamran Shehzad; Samiullah, Tahir Rehman; Muzaffar, Adnan; Nasir, Idrees Ahmad; Husnain, Tayyab

2015-12-01

Gossypium arboreumis resistant to Cotton leaf curl Burewala virus and its cognate Cotton leaf curl Multan beta satellite ( CLCuBuV and CLCuMB ). However, the G. arboreum wax deficient mutant (GaWM3) is susceptible to CLCuV . Therefore, epicuticular wax was characterized both quantitatively and qualitatively for its role as physical barrier against whitefly mediated viral transmission and co-related with the titer of each viral component (DNA-A, alphasatellite and betasatellite) in plants. The hypothesis was the CLCuV titer in cotton is dependent on the amount of wax laid down on plant surface and the wax composition. Analysis of the presence of viral genes, namely alphasatellite, betasatellite and DNA-A, via real-time PCR in cotton species indicated that these genes are detectable in G. hirsutum , G. harknessii and GaWM3, whereas no particle was detected in G. arboreum . Quantitative wax analysis revealed that G. arboreum contained 183 μg.cm -2 as compared to GaWM3 with only 95 μg.cm -2 . G. hirsutum and G. harknessii had 130 μg.cm -2 and 146 μg.cm -2 , respectively. The GCMS results depicted that Lanceol, cis was 45% in G. harknessii . Heptadecanoic acid was dominant in G. arboreum with 25.6%. GaWM3 had 18% 1,2,-Benenedicarboxylic acid. G. hirsutum contained 25% diisooctyl ester. The whitefly feeding assay with Nile Blue dye showed no color in whiteflies gut fed on G. arboreum . In contrast, color was observed in the rest of whiteflies. From results, it was concluded that reduced quantity as well as absence of (1) 3-trifluoroacetoxytetradecane, (2) 2-piperidinone,n-|4-bromo-n-butyl|, (3) 4-heptafluorobutyroxypentadecane, (4) Silane, trichlorodocosyl-, (5) 6- Octadecenoic acid, methyl ester, and (6) Heptadecanoicacid,16-methyl-,methyl ester in wax could make plants susceptible to CLCuV , infested by whiteflies.

Injurious effects of wool and grain dusts on alveolar epithelial cells and macrophages in vitro.

Science.gov (United States)

Brown, D M; Donaldson, K

1991-01-01

Epidemiological studies of workers in wool textile mills have shown a direct relation between the concentration of wool dust in the air and respiratory symptoms. Injurious effects of wool dust on the bronchial epithelium could be important in causing inflammation and irritation. A pulmonary epithelial cell line in vitro was therefore used to study the toxic effects of wool dust. Cells of the A549 epithelial cell line were labelled with 51Cr and treated with whole wool dusts and extracts of wool, after which injury was assessed. Also, the effects of grain dust, which also causes a form of airway obstruction, were studied. The epithelial injury was assessed by measuring 51Cr release from cells as an indication of lysis, and by monitoring cells which had detached from the substratum. No significant injury to A549 cells was caused by culture with any of the dusts collected from the air but surface "ledge" dust caused significant lysis at some doses. Quartz, used as a toxic control dust, caused significant lysis at the highest concentration of 100 micrograms/well. To determine whether any injurious material was soluble the dusts were incubated in saline and extracts collected. No extracts caused significant injury to epithelial cells. A similar lack of toxicity was found when 51Cr labelled control alveolar macrophages were targets for injury. Significant release of radiolabel was evident when macrophages were exposed to quartz at concentrations of 10 and 20 micrograms/well, there being no significant injury with either wool or grain dusts. These data suggest that neither wool nor grain dust produce direct injury to epithelial cells, and further studies are necessary to explain inflammation leading to respiratory symptoms in wool and grain workers. PMID:2015211

The graft polymers from different species of lignin and acrylic acid: synthesis and mechanism study.

Science.gov (United States)

Ye, De zhan; Jiang, Li; Ma, Chao; Zhang, Ming-hua; Zhang, Xi

2014-02-01

The influence of lignin species on the grafting mechanism of lignosulfonate (from eucalyptus and pine, recorded as HLS and SLS, respectively) with acrylic acid (AA) was investigated. The graft polymers were confirmed by the absorption of carbonyl groups in the FTIR spectra. The decreasing phenolic group's content (Ph-OH) is not only due to its participation as grafting site but also to the negative effect of initiator. In the initial period (0-60 min), HLS and SLS both accelerate the polymerization of AA. Additionally, Ph-OH group's content is proportional to product yield (Y%), monomer conversion (C%) and grafting efficiency (GE%), strongly indicating that it acts as active center. Nevertheless, compared with HLS, Y% and C% in SLS grafting system are lower though it has higher Ph-OH group's content, which is due to the quinonoid structure formed by the self-conjugated of phenoxy radical in Guaiacyl unit. Finally, the lignosulfonate grafting mechanism was proposed. Copyright © 2013 Elsevier B.V. All rights reserved.

Genome-wide functional analysis of cotton (Gossypium hirsutum in response to drought.

Directory of Open Access Journals (Sweden)

Yun Chen

Full Text Available Cotton is one of the most important crops for its natural textile fibers in the world. However, it often suffered from drought stress during its growth and development, resulting in a drastic reduction in cotton productivity. Therefore, study on molecular mechanism of cotton drought-tolerance is very important for increasing cotton production. To investigate molecular mechanism of cotton drought-resistance, we employed RNA-Seq technology to identify differentially expressed genes in the leaves of two different cultivars (drought-resistant cultivar J-13 and drought-sensitive cultivar Lu-6 of cotton. The results indicated that there are about 13.38% to 18.75% of all the unigenes differentially expressed in drought-resistant sample and drought-sensitive control, and the number of differentially expressed genes was increased along with prolonged drought treatment. DEG (differentially expression gene analysis showed that the normal biophysical profiles of cotton (cultivar J-13 were affected by drought stress, and some cellular metabolic processes (including photosynthesis were inhibited in cotton under drought conditions. Furthermore, the experimental data revealed that there were significant differences in expression levels of the genes related to abscisic acid signaling, ethylene signaling and jasmonic acid signaling pathways between drought-resistant cultivar J-13 and drought-sensitive cultivar Lu-6, implying that these signaling pathways may participate in cotton response and tolerance to drought stress.

Poly(vinylbenzyl sulfonic acid)-grafted poly(ether ether ketone) membranes

Energy Technology Data Exchange (ETDEWEB)

Hwang, Mi-Lim; Choi, Jisun; Woo, Hyun-Su; Kumar, Vinod; Sohn, Joon-Yong; Shin, Junhwa, E-mail: shinj@kaeri.re.kr

2014-02-15

Highlights: • PEEK-g-PVBSA, a polymer electrolyte membrane was prepared by a radiation grafting technique. • Poly(ether ether ketone) (PEEK), an aromatic hydrocarbon polymer was used as a grafting backbone film. • The water uptake, proton conductivity, and methanol permeability of the membranes were evaluated. • PEEK-g-PVBSA membranes show considerably lower methanol permeability compared to a Nafion membrane. -- Abstract: In this study, an aromatic hydrocarbon based polymer electrolyte membrane, poly(vinylbenzyl sulfonic acid)-grafted poly(ether ether ketone) (PEEK-g-PVBSA), has been prepared by the simultaneous irradiation grafting of vinylbenzyl chloride (VBC) monomer onto a PEEK film and subsequent sulfonation. Each chemical conversion was monitored by FT-IR and SEM–EDX instruments. The physicochemical properties including IEC, water uptake, proton conductivity, and methanol permeability of the prepared membranes were also investigated and found that the values of these properties increase with the increase of degree of grafting. It was observed that the IEC values of the prepared PEEK-g-PVBSA membranes with 32%, 58%, and 80% DOG values were 0.50, 1.05, and 1.22 meq/g while the water uptakes were 14%, 20%, and 21%, respectively. The proton conductivities (0.0272–0.0721 S/cm at 70 °C) were found to be somewhat lower than Nafion 212 (0.126 S/cm at 70 °C) at a relative humidity of 90%. However, the prepared membranes showed a considerably lower methanol permeability (0.61–1.92 × 10{sup −7} cm{sup 2}/s) compared to a Nafion 212 membrane (5.37 × 10{sup −7} cm{sup 2}/s)

Radiation grafting of hydrophilic monomers on to plasticized poly(vinyl chloride) sheets: Pt. 1

International Nuclear Information System (INIS)

Kalliyana Krishnan, V.; Jayakrishnan, A.; Francis, J.D.

1990-01-01

Medical-grade plasticized polyvinyl chloride (PVC) sheets were surface modified using gamma-radiation grafting of a combination of hydrophilic monomers based on 2-hydroxyethyl methacrylate (HEMA) and N-vinyl pyrrolidone (NVP). The properties of the modified surfaces were evaluated using contact angle measurements, phase-contrast photomicroscopy and scanning electron microscopy. Surface energy calculations indicated that the surfaces became highly hydrophilic when grafted with even a 1% (v/v) solution of HEMA-NVP combination in the presence of 0.005 M CuSO 4 . Migration of the plasticizer di(2-ethylhexyl phthalate) from the grafted sheets was examined in hydrocarbon solvents such as n-hexane, n-heptane and n-octane and in extractant media such as cotton seed oil and polyethylene glycol-400 (PEG-400). The migration was found to be 0 C over a period of 5 h. Accelerated leaching studies in cotton seed oil and PEG-400 demonstrated that virtually no plasticizer migrated out in the former over a period of 96 h whereas the rate of migration in the latter medium showed only a mild reduction. The migration behaviour was Fickian in nature for grafted sheets. The method described may be useful as a simple, versatile technique for preventing plasticizer migration from plasticized PVC for medical applications. (author)

Assessment of rock wool as support material for on-site sanitation: hydrodynamic and mechanical characterization.

Science.gov (United States)

Wanko, Adrien; Laurent, Julien; Bois, Paul; Mosé, Robert; Wagner-Kocher, Christiane; Bahlouli, Nadia; Tiffay, Serge; Braun, Bouke; Provo kluit, Pieter-Willem

2016-01-01

This study proposes mechanical and hydrodynamic characterization of rock wool used as support material in compact filter. A double-pronged approach, based on experimental simulation of various physical states of this material was done. First of all a scanning electron microscopy observation allows to highlight the fibrous network structure, the fibres sizing distribution and the atomic absorption spectrum. The material was essentially lacunar with 97 ± 2% of void space. Static compression tests on variably saturated rock wool samples provide the fact that the strain/stress behaviours depend on both the sample conditioning and the saturation level. Results showed that water exerts plastifying effect on mechanical behaviour of rock wool. The load-displacement curves and drainage evolution under different water saturation levels allowed exhibiting hydraulic retention capacities under stress. Finally, several tracer experiments on rock wool column considering continuous and batch feeding flow regime allowed: (i) to determine the flow model for each test case and the implications for water dynamic in rock wool medium, (ii) to assess the rock wool double porosity and discuss its advantages for wastewater treatment, (iii) to analyse the benefits effect for water treatment when the high level of rock wool hydric retention was associated with the plug-flow effect, and (iv) to discuss the practical contributions for compact filter conception and management.

Development of Graft Copolymer Flocculant Based on Acrylamide and Acrylic Acid for the dewatering of coal

International Nuclear Information System (INIS)

Mahmoud, G.A.; Abdel Khalek, M.A

2012-01-01

Most coal preparation processes were carried out in water medium. The water content of coal product has a negative impact on handling and specific energy value. The moisture content may be attributed to the proportion of fine coal, which presents the greatest dewatering problem. A novel polymeric flocculant has been developed by graft copolymerization of acrylamide (AAm) with acrylic acid (AAc) using gamma irradiation technique. The grafted copol621621ymer P(AAm/AAc) was characterized by Fourier-transform infrared spectroscopy (FTIR), and thermo-gravimetric analysis (TGA). The effects of reaction parameters, such as total absorbed dose, and monomer concentration on grafting yield were investigated. The flocculation performance of the graft copolymer P(AAm/AAc) was investigated in coal suspension. It was observed that the grafting ratio was one of the key factors for the flocculating effects. The copolymers with various grafting ratios showed different flocculating properties. It was found that as the grafting ratio increased, the flocculating effect also increased. The flocculation performance of the grafted copolymer was better than that of the commercial flocculant, poly-acrylamide (Magnafloc 1011).

Multifunctional AgNPs@Wool: colored, UV-protective and antioxidant functional textiles

Science.gov (United States)

Shabbir, Mohd; Mohammad, Faqeer

2018-02-01

Nanomaterials have great impact on textile industry for multifunctional and smart clothing as per the need of present, and further, green nanotechnology is the current hotspot of research and industrial developments. Silver nanoparticles (AgNPs) are synthesized (in situ) by using natural compounds of plant extracts (naphthoquinones, phenolics/flavonoids, polyphenols) as reducing or stabilizing agents, and simultaneously deposited on wool fabric for coloration, UV protection and antioxidant properties. UV-visible spectroscopy is used to monitor the route of biosynthesis of nanoparticles and transmission electron microscopy for morphological characteristics of synthesized AgNPs. Spherical and almost oval-shaped AgNPs were synthesized by naphthoquinones, polyphenols and flavonoids, respectively. Scanning electron microscopy (SEM) coupled with energy dispersive X-ray (EDX) spectroscopy, X-ray diffraction pattern (XRD) and Fourier transform infrared spectroscopy were used for the AgNPs@Wool fabrics characterization. SEM-EDX analysis and XRD patterns confirmed the successful deposition of silver nanoparticles on wool. Coloration characteristics in terms of color strength (K/S) and CIEL*a*b*c*h° values, UV protection abilities in terms of UV transmittance and UV protection factor, and % antioxidant activity of AgNPs@Wool are suggestive of good-to-excellent results.

Reaction Mechanisms and Structural and Physicochemical Properties of Caffeic Acid Grafted Chitosan Synthesized in Ascorbic Acid and Hydroxyl Peroxide Redox System.

Science.gov (United States)

Liu, Jun; Pu, Huimin; Chen, Chong; Liu, Yunpeng; Bai, Ruyu; Kan, Juan; Jin, Changhai

2018-01-10

The ascorbic acid (AA) and hydroxyl peroxide (H 2 O 2 ) redox pair induced free radical grafting reaction is a promising approach to conjugate phenolic groups with chitosan (CS). In order to reveal the exact mechanisms of the AA/H 2 O 2 redox pair induced grafting reaction, free radicals generated in the AA/H 2 O 2 redox system were compared with hydroxyl radical ( • OH) produced in the Fe 2+ /H 2 O 2 redox system. Moreover, the structural and physicochemical properties of caffeic acid grafted CS (CA-g-CS) synthesized in these two redox systems were compared. Results showed that only ascorbate radical (Asc •- ) was produced in the AA/H 2 O 2 system. The reaction between Asc •- and CS produced novel carbon-centered radicals, whereas no new free radicals were detected when • OH reacted with CS. Thin layer chromatography, UV-vis, Fourier transform infrared, and nuclear magnetic resonance spectroscopic analyses all confirmed that CA was successfully grafted onto CS through Asc •- . However, CA could be hardly grafted onto CS via • OH. CA-g-CS synthesized through Asc •- exhibited lower thermal stability and crystallinity than the reaction product obtained through • OH. For the first time, our results demonstrated that the synthesis of CA-g-CS in the AA/H 2 O 2 redox system was mediated by Asc •- rather than • OH.

FUBT, a putative MFS transporter, promotes secretion of fusaric acid in the cotton pathogen Fusarium oxysporum f.sp. vasinfectum

Science.gov (United States)

Fusaric acid (FA), a phytotoxic polyketide produced by Fusarium oxysporum f. sp. vasinfectum (FOV), has been shown to be associated with disease symptoms on cotton. A gene located upstream of the polyketide synthase gene responsible for the biosynthesis of FA is predicted to encode a member of the ...

Analysis Of The Reactivity Of Radpro Solution With Cotton Rags

International Nuclear Information System (INIS)

Marusich, R.M.

2009-01-01

Rags containing RadPro(reg s ign) solution will be generated during the decontamination of the Plutonium Finishing Plant (PFP). Under normal conditions, the rags will be neutralized with sodium carbonate prior to placing in the drums. The concern with RadPro solutions and cotton rags is that some of the RadPro solutions contain nitric acid. Under the right conditions, nitric acid and cotton rags exothermically react. The concern is, will RadPro solutions react with cotton rags exothermically? The potential for a runaway reaction for any of the RadPro solutions used was studied in Section 5.2 of PNNL-15410, Thermal Stability Studies of Candidate Decontamination Agents for Hanford's Plutonium Finishing Plant Plutonium-Contaminated Gloveboxes. This report shows the thermal behavior of cotton rags having been saturated in one of the various neutralized and non-neutralized RadPro solutions. The thermal analysis was performed using thermogravimetric Analysis (TGA), Differential Thermal Analysis (DTA) and Accelerating Rate Calorimetry (ARC).

Drought coping strategies in cotton: increased crop per drop.

Science.gov (United States)

Ullah, Abid; Sun, Heng; Yang, Xiyan; Zhang, Xianlong

2017-03-01

The growth and yield of many crops, including cotton, are affected by water deficit. Cotton has evolved drought specific as well as general morpho-physiological, biochemical and molecular responses to drought stress, which are discussed in this review. The key physiological responses against drought stress in cotton, including stomata closing, root development, cellular adaptations, photosynthesis, abscisic acid (ABA) and jasmonic acid (JA) production and reactive oxygen species (ROS) scavenging, have been identified by researchers. Drought stress induces the expression of stress-related transcription factors and genes, such as ROS scavenging, ABA or mitogen-activated protein kinases (MAPK) signalling genes, which activate various drought-related pathways to induce tolerance in the plant. It is crucial to elucidate and induce drought-tolerant traits via quantitative trait loci (QTL) analysis, transgenic approaches and exogenous application of substances. The current review article highlights the natural as well as engineered drought tolerance strategies in cotton. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

Polymethacrylic acid grafted psyllium (Psy- g-PMA): a novel material for waste water treatment

Science.gov (United States)

Kumar, Ranvijay; Sharma, Kaushlendra; Tiwary, K. P.; Sen, Gautam

2013-03-01

Polymethacrylic acid grafted psyllium (Psy- g-PMA) was synthesized by microwave assisted method, which involves a microwave irradiation in synergism with silver sulfate as a free radical initiator to initiate grafting reaction. Psy- g-PMA grades have been synthesized and characterized on structural basis (elemental analysis, FTIR spectroscopy, intrinsic viscosity study) as well as morphological and thermal studies, taking psyllium as reference. The effects of reaction time, amount of monomer and silver sulfate (free radical initiator) on grafting of PMA on psyllium backbone have been studied. It is observed that all the grades of Psy- g-PMA have higher intrinsic viscosities than that of psyllium. The best synthesized grade was Psy- g-PMA having intrinsic viscosity of 6.93 and 58 % grafting of PMA on the main polymer backbone. Further Psy- g-PMA applications as flocculants for waste water treatment have been investigated. Psy- g-PMA resulted in higher decrease in the flocculation parameters such as total dissolved solid or total solids compared to psyllium. Hence the result shows the possible application of grafted psyllium in wastewater treatment.

Gastric tricho-wool bezoar in an 18-year-old girl | Gurzu | South ...

African Journals Online (AJOL)

An 18-year-old girl with no psychiatric history presented with abdominal pain. Four months previously she had given birth to a healthy baby. On palpation, a painful abdominal mass was identified in the epigastric region, and gastrotomy was performed. A J-shaped hair-wool ball and two large pieces of sheep's wool were ...

Effects of ractopamine hydrochloride on growth performance and carcass characteristics in wool and hair lambs

Directory of Open Access Journals (Sweden)

Ángel M. Romero-Maya

2013-06-01

Full Text Available This study aimed at evaluating the effects of ractopamine hydrochloride (RAC on growth performance and carcass characteristics of wool and hair lambs. For this purpose, 48 lambs averaging 31.3 kg body weight, of which twenty were wool (Ramboullet x Suffolk and twenty eight were hair (Tabasco lambs, and four levels of RAC (0, 10, 20, and 30 mg/kg diet, dry matter basis were used. Wool lambs fed 20 and 30 mg RAC had higher (P<0.05 total gain weight and lower feed conversion than 0 and 10 mg RAC. Wool lambs fed 20 mg RAC had the highest carcass weight, dressing, legs weight and longissimus area as compared to 0, 10 and 30 mg RAC.  In hair lambs there were not effect of RAC on growth performance and carcass characteristics.It was concluded that addition of RAC to finishing diets offered the best growth performance and carcass traits in wool lambs as compared to hair lambs. 

Usability of Particle Film Technology and Water Holding Materials to Improve Drought Tolerance in Gossypium hirsutum L. Plants

Science.gov (United States)

Roy, K.; Zwieniecki, M.

2017-12-01

Cotton (Gossypium hirsutum L.) is relatively drought resistant and thus is planted widely in many semi-arid and arid parts of the world, many of which are usually deprived of modern water management technologies. Since the productivity of cotton plants depends on water availability, we carried out the present research aiming at testing two different low cost and arid-environment friendly water efficient techniques: application of particle film technology on leaves to reduce the transpiration rate (kaolin dust), and use of organic material to improve the soil water holding capacity (cotton wool). In details, kaolin (3% and 5%; weight:volume) mixed in water was sprayed on the upper surface of the leaves of young plants, and small amounts of cotton wool (0.1%, 0.3% and 0.5%; weight:weight) were mixed into the soils. The study showed that kaolin spray was useful as a transpiration reducing agent only if plants have adequate water in the soil (well irrigated) but not under water stress conditions. In addition, mixing a small amount of cotton wool into the soil can significantly increase the amount of water available to the plants, and extend the benefit of kaolin application on plants.

Antioxidant multi-walled carbon nanotubes by free radical grafting of gallic acid: new materials for biomedical applications.

Science.gov (United States)

Cirillo, Giuseppe; Hampel, Silke; Klingeler, Rüdiger; Puoci, Francesco; Iemma, Francesca; Curcio, Manuela; Parisi, Ortensia Ilaria; Spizzirri, Umile Gianfranco; Picci, Nevio; Leonhardt, Albrecht; Ritschel, Manfred; Büchner, Bernd

2011-02-01

To prove the possibility of covalently functionalizing multi-walled carbon nanotubes (CNTs) by free radical grafting of gallic acid on their surface with the subsequent synthesis of materials with improved biological properties evaluated by specific in-vitro assays. Antioxidant CNTs were synthesized by radical grafting of gallic acid onto pristine CNTs. The synthesis of carbon nanotubes was carried out in a fixed-bed reactor and, after the removal of the amorphous carbon, the grafting process was performed. The obtained materials were characterized by fluorescence and Fourier transform infrared spectroscopy (FT-IR) analyses. After assessment of the biocompatibility and determination of the disposable phenolic group content, the antioxidant properties were evaluated in terms of total antioxidant activity and scavenger ability against 2,2'-diphenyl-1-picrylhydrazyl (DPPH), hydroxyl and peroxyl radicals. Finally the inhibition activity on acetylcholinesterase was evaluated.   The covalent functionalization of CNTs with gallic acid was confirmed and the amount of gallic acid bound per g of CNTs was found to be 2.1±0.2 mg. Good antioxidant and scavenging properties were recorded in the functionalized CNTs, which were found to be able to inhibit the acetylcholinesterase with potential improved activity for biomedical and pharmaceutical applications. For the first time, a free radical grafting procedure was proposed as a synthetic approach for the covalent functionalization of CNTs with an antioxidant polyphenol. © 2010 The Authors. JPP © 2010 Royal Pharmaceutical Society.

Clinical results of arthroscopic polyglycolic acid sheet patch graft for irreparable rotator cuff tears

Directory of Open Access Journals (Sweden)

Yu Mochizuki

2015-01-01

Full Text Available The high retear rates after surgery for irreparable rotator cuff tears can be explained by the healing capacity potential of tendons and the native rotator cuff enthesis characterised by complex morphological structures, called direct insertion. Many experimental researches have focused on biologically augmenting the rotator cuff reconstruction and improving tendon–bone healing of the rotator cuff. The results of the experimental study showed that the polyglycolic acid sheet scaffold material allows for the regeneration of not only tendon-to-tendon, but also tendon-to-bone interface in an animal model. We performed a clinical study of the arthroscopic polyglycolic acid sheet patch graft used for the repair of irreparable rotator cuff tears. One-year clinical results of the repair of irreparable rotator cuff tears by arthroscopic patch graft with a polyglycolic acid sheet demonstrated improved shoulder function and a significantly lower retear rate, compared with patients treated with a fascia lata patch.

Bioremoval of Basic Violet 3 and Acid Blue 93 by Pseudomonas putida and its adsorption isotherms and kinetics.

Science.gov (United States)

Arunarani, A; Chandran, Preethy; Ranganathan, B V; Vasanthi, N S; Sudheer Khan, S

2013-02-01

Basic Violet 3 and Acid Blue 93 are the most important group of synthetic colourants extensively used in textile industries for dyeing cotton, wool, silk and nylon. Release of these dye pollutants in to the environment adversely affects the human health and aquatic organisms. The present study we used Pseudomonas putida MTCC 4910 for the adsorptive removal of Basic Violet 3 and Acid Blue 93 from the aqueous solutions. The pH (4-9) and NaCl concentrations (1mM-1M) did not influence the adsorption process. The equilibrium adsorption process fitted well to Freundlich model than Langmuir model. The kinetics of adsorption fitted well by pseudo-second-order. Thus in the present study an attempt has been made to exploit the dye removal capability of P. putida MTCC 4910, and it was found to be an efficient microbe that could be used for bio removal of dyes from textile effluents. Copyright © 2012 Elsevier B.V. All rights reserved.

Electron-beam-induced post-grafting polymerization of acrylic acid onto the surface of Kevlar fibers

Science.gov (United States)

Xu, Lu; Hu, Jiangtao; Ma, Hongjuan; Wu, Guozhong

2018-04-01

The surface of Kevlar fibers was successfully modified by electron beam (EB)-induced post-grafting of acrylic acid (AA). The generation of radicals in the fibers was confirmed by electron spin resonance (ESR) measurements, and the concentration of radicals was shown to increase as the absorbed dose increased, but decrease with increasing temperature. The influence of the synthesis conditions on the degree of grafting was also investigated. The surface microstructure and chemical composition of the modified Kevlar fibers were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The SEM images revealed that the surface of the grafted fibers was rougher than those of the pristine and irradiated fibers. XPS analysis confirmed an increase in C(O)OH groups on the surface of the Kevlar fibers, suggesting successful grafting of AA. These results indicate that EB-induced post-grafting polymerization is effective for modifying the surface properties of Kevlar fibers.

Hydrogels from feather keratin show higher viscoelastic properties and cell proliferation than those from hair and wool keratins.

Science.gov (United States)

Esparza, Yussef; Bandara, Nandika; Ullah, Aman; Wu, Jianping

2018-09-01

Hydrogel prepared from keratin shows potential applications in tissue engineering. However, the importance of the keratin sources has not been considered. The objectives of this study were to characterize and compare the rheological (storage modulus), physical (porosity, pore size, swelling capacity, and water contact angle) and in vitro cell compatibility of hydrogel scaffolds prepared from various keratin sources. Keratins were characterized by means of their molecular weight, amino acid composition, thermal and conformational properties. Hydrogels from chicken feather keratins demonstrated substantially higher storage modulus (G') than hair and wool keratin hydrogels. However, higher swelling capacity (>3000%) was determined in hair and wool over feather keratin (1500%) hydrogels. Our results suggest that small molecular weight and β-sheet conformation of feather keratin (~10 kDa) facilitated the self-assembly of rigid hydrogels through disulfide bond re-oxidation. Whereas, high molecular weight (10-75 kDa) stretchable α-helix conformation in hair and wool keratins resulted in weaker hydrogels. The cell cultures using fibroblasts showed the highest proliferation rate on chicken feather keratin hydrogel scaffolds. After 15 days of culture, partial breakdown of keratin fibers was observed. Results indicate that stiffer avian keratins can be used to fabricate more mechanically robust biomaterials than mammalian keratins. Copyright © 2018 Elsevier B.V. All rights reserved.

Preparation of polymethacrylic acid-grafted HEMA/PVP microspheres and preliminary study on basic protein adsorption.

Science.gov (United States)

Gao, Baojiao; Hu, Hongyan; Guo, Jianfeng; Li, Yanbin

2010-06-01

The crosslinked copolymeric microspheres (HEMA/NVP) of N-vinylpyrrolidone (NVP) and 2-hydroxyethyl methacrylate (HEMA) were prepared using inverse suspension polymerization method. Subsequently, the reaction of methacryloyl chloride with the hydroxyl groups on the surfaces of HEMA/NVP microspheres was performed, leading to the introduction of polymerisable double bonds onto the surfaces of microspheres HEMA/NVP. Afterward, methacrylic acid was allowed to be graft-polymerized on microspheres HEMA/NVP in the manner of "grafting from", resulting in the grafted microspheres PMAA-HEMA/NVP. The grafted microspheres PMAA-HEMA/NVP were fully characterized with several means. The graft-polymerization of MAA on microspheres HEMA/NVP was studied in detail, and the optimal reaction conditions were determined. Thereafter, the adsorption property of the grafted microspheres PMAA-HEMA/NVP for lysozyme as a basic protein model was preliminarily examined to explore the feasibility of removing deleterious basic protein such as density lipoprotein from blood. The experimental results indicate that the PMAA grafting degree on microspheres HEMA/NVP is limited because an enwinding polymer layer as a kinetic barrier on the surfaces of HEMA/NVP microspheres will be formed during the graft-polymerization, and block the graft-polymerization. In order to enhance PMAA grafting degree, reaction temperature, monomer concentration and the used amount of initiator should be effectively controlled. The experimental results also reveal that the grafted microspheres PMAA-HEMA/NVP possess very strong adsorption ability for lysozyme by right of strong electrostatic interaction. Copyright 2010 Elsevier B.V. All rights reserved.

Amino Acid Content of the Gamma Irradiated Cotton Leaf-Worm, Spodoptera Littoralis (Boisd.)

International Nuclear Information System (INIS)

Sobeiha, A.K.; Sallam, H.A.; El-Shall, S.S.A.

2000-01-01

The effects of gamma irradiation on amino acid content of the cotton leaf worm Spodoptera Littoralis was studied.The identified amino acids in the total body tissue of male moths were Theronine, Serine, Glutamic, Glycine, Alanine, Valine, Cystine, Methionine, Isoleucine, Leucine, Tyrosine, Phenylalanine, Lysine, Histidine and Arginine. The irradiation of full grown male pupae with doses 100,200 and 300 Gy decreased the total quantity of amino acids and the amount of most individual amino acids in male moths of P 1 or F 1 generations with some exceptions for Threonine, Alanine, Glycine, Serine, Valine, Cystine and Methionine which were increased.The effect of irradiation on amino acid content of the reproductive system tissues for each male or female were also studied.The results indicated that irradiation decreased the total quantity of amino acid content of both sexes by increasing the dose and males were more radiosensitive than females. Also, irradiation decreased the amount of individual amino acids in both sexes with certain exceptions, e.g. Alanine, Methionine and Tyrosine which increased in the reproductive system of male, and Methionine which increased by more than four times as control.The amino acid content was determined as well in F 1 egg progeny, which was produced from irradiated males Irradiation doses (100, 200 and 300 Gy) decreased the total quantity of amino acids, and all individual ones except Cystine.The greatest reduction (54.9% was observed with Lysine at 300 Gy as compared to control

Insertion of marble waste in the production chain of glass wool

International Nuclear Information System (INIS)

Rodrigues, G.F.; Alves, J.O.; Espinosa, D.C.R.; Tenorio, J.A.S.

2010-01-01

The work aimed the study of the recycle of the waste from marble cutting, aiming the reuse as partial raw material in the production of glass wool. Glass wool are materials with chemical and mechanical resistance, durability and lightness, and also important thermo-acoustic properties. A mixture of the waste with chemical additives was melted in a laboratory electric furnace using temperature of 1450 deg C. The melted material was directly poured in a water-filled recipient aiming the rapidly cooling. Samples of the produced material were characterized by XRD, SEM and DTA. The results showed that the residue from marble cutting can be inserted into the productive chain of glass wool, providing a decrease in the extraction of mineral resources, a profitable destination for this waste, and a economy for the companies producer of thermo-acoustic insulators. (author)

Moisture dependent thermal properties of hydrophilic mineral wool: application of the effective media theory

Directory of Open Access Journals (Sweden)

Iñigo Antepara

2015-09-01

Full Text Available Thermal properties of mineral wool based materials appear to be of particular importance for their practical applications because the majority of them is used in the form of thermal insulation boards. Every catalogue list of any material producer of mineral wool contains thermal conductivity, sometimes also specific heat capacity, but they give only single characteristic values for dry state of material mostly. Exposure to outside climate or any other environment containing moisture can negatively affect the thermal insulation properties of mineral wool. Nevertheless, the mineral wool materials due to their climatic loading and their environmental exposure contain moisture that can negatively affect their thermal insulation properties. Because the presence of water in mineral wool material is undesirable for the majority of applications, many products are provided with hydrophobic substances. Hydrophilic additives are seldom used in mineral wool products. However, this kind of materials has a good potential for application for instance in interior thermal insulation systems, masonry desalination, green roofs, etc. For these materials, certain moisture content must be estimated and thus their thermal properties will be different than for the dry state. On this account, moisture dependent thermal properties of hydrophilic mineral wool (HMW are studied in a wide range of moisture content using a pulse technique. The experimentally determined thermal conductivity data is analysed using several homogenization formulas based on the effective media theory. In terms of homogenization, a porous material is considered as a mixture of two or three phases. In case of dry state, material consists from solid and gaseous phase. When moistened, liquid phase is also present. Mineral wool consists of the solid phase represented by basalt fibers, the liquid phase by water and the gaseous phase by air. At first, the homogenization techniques are applied for the

Radiation Synthesis of Poly(N-Vinyl Pyrrolidone) Nanogels and Nanoscale Grafting of Poly(Acrylic Acid) from Cellulose

Energy Technology Data Exchange (ETDEWEB)

Guven, Olgun; Isik, Semiha Duygu; Barsbay, Murat [Hacettepe University, Department of Chemistry, 06800 Ankara (Turkey)

2010-07-01

Ionizing radiation has long been known to be a very useful tool for the preparation of nanogels. Although preparation is straightforward, the control of the sizes of nanogels has been a challenging issue. This report shows the results of our work on using radiation for the synthesis of PVP nanogels in the range of 40-200nm by making use of the principles of solution thermodynamics of aqueous polymer solutions. Nanoscale grafting of responsive polymers however has been of scientific and industrial importance due to fine control of the molecular weight and molecular weight distribution of grafted polymers. The second part of this report deals with the grafting of poly(acrylic acid) onto the surface of cellulose, thus imparting pH response to the substrate. The use of radiation as a constant source of radical generation and Reversible-Addition-Fragmentation-Chain transfer agents for the control of free radical polymerization provided a full control over the molecular weight and distribution of poly(acrylic acid) grafts on cellulose. (author)

Radiation Synthesis of Poly(N-Vinyl Pyrrolidone) Nanogels and Nanoscale Grafting of Poly(Acrylic Acid) from Cellulose

International Nuclear Information System (INIS)

Guven, Olgun; Isik, Semiha Duygu; Barsbay, Murat

2010-01-01

Ionizing radiation has long been known to be a very useful tool for the preparation of nanogels. Although preparation is straightforward, the control of the sizes of nanogels has been a challenging issue. This report shows the results of our work on using radiation for the synthesis of PVP nanogels in the range of 40-200nm by making use of the principles of solution thermodynamics of aqueous polymer solutions. Nanoscale grafting of responsive polymers however has been of scientific and industrial importance due to fine control of the molecular weight and molecular weight distribution of grafted polymers. The second part of this report deals with the grafting of poly(acrylic acid) onto the surface of cellulose, thus imparting pH response to the substrate. The use of radiation as a constant source of radical generation and Reversible-Addition-Fragmentation-Chain transfer agents for the control of free radical polymerization provided a full control over the molecular weight and distribution of poly(acrylic acid) grafts on cellulose. (author)

The effect of butyric acid with autogenous omental graft on healing of experimental Achilles tendon injury in rabbits.

Science.gov (United States)

Jahani, S; Moslemi, H R; Dehghan, M M; Sedaghat, R; Mazaheri Nezhad, R; Rezaee Moghaddam, D

2015-01-01

In this study, the role of local injection of butyric acid (BA) with autogenous omental graft was evaluated in healing of experimental Achilles tendon injury in rabbits. Nine adult male New Zealand rabbits were anesthetized and a partial thickness tenotomy was created on both hindlimbs. In treated group, omental graft was secured in place using BA soaked polygalactin 910 suture. In control group, the graft was sutured without BA. Butyric acid and normal saline were injected daily to treatment and control groups for three days, respectively. Based on the findings, on day 15 after injury, the tendon sections showed that healing rate in BA treated group was higher than that in control group. Furthermore, at days 28 and 45, comparison between BA treated and control groups demonstrated that BA increased the healing rate but with no significance. In summary, results of this study show that application of BA with autogenous omental graft can improve healing process of damaged Achilles tendon.

Preparation of Poly(Vinyl Alcohol) Grafted With Acrylic Acid/Styrene Binary Monomers For Selective Permeation of Heavy Metals

International Nuclear Information System (INIS)

Hegazy El-Sayed, A.; Abd El-Rehim, H.A.; Ali, A.M.; Aly, H.F.

1999-01-01

A study has been made to modify water-soluble poly(vinyl alcohol) (PVA), by grafting acrylic acid and styrene (AAc/Sty) binary monomers using gamma rays as initiator. The factors that affect the preparation process and grafting yield were studied and more economical grafts under the most favorable reaction conditions were obtained. It was found that the high degree of grafting of such system was obtained in presence of ethanol-water mixture in which water plays a significant role in enhancing the graft copolymerization. The critical amount of water to afford maximum grafting yield has been evaluated. The effect of comonomer composition on the grafting yield was also investigated and it was observed that using a mixture of AAc/Sty monomers influence the extent of grafting of each monomer onto the PVA substrate and the phenomenon of synergism occurs during such reaction. Also, degree of grafting increases as the content of the solvent decreases in the reaction medium. The permeation of heavy metals such as Ni and Co through the grafted membranes was investigated and efficiency of separation process is also determined

Microstructural characterization of stone wool fibre network

DEFF Research Database (Denmark)

Chapelle, Lucie; Brøndsted, Povl; Kusano, Yukihiro

2014-01-01

Understanding the mechanical properties of fibrous network as complex as stone wool materials requires a relevant description of their microstructure and architecture. In this study, different methods have been proposed to characterize the fibre orientation, diameter and length of fibres as well...

Investigations into the Anti-Felting Properties of Sputtered Wool Using Plasma Treatment

International Nuclear Information System (INIS)

Borghei, S. M.; Shahidi, S.; Ghoranneviss, M.; Abdolahi, Z.

2013-01-01

In this research the effects of mordant and plasma sputtering treatments on the crystallinity and morphological properties of wool fabrics were investigated. The felting behavior of the treated samples was also studied. We used madder as a natural dye and copper sulfate as a metal mordant. We also used copper as the electrode material in a DC magnetron plasma sputtering device. The anti-felting properties of the wool samples before and after dying was studied, and it was shown that the shrink resistance and anti-felting behavior of the wool had been significantly improved by the plasma sputtering treatment. In addition, the percentage of crystallinity and the size of the crystals were investigated using an X-ray diffractometer, and a scanning electron microscope was used for morphological analysis. The amount of copper particles on the surface of the mordanted and sputtered fabrics was studied using the energy dispersive X-ray (EDX) method, and the hydrophobic properties of the samples were examined using the water drop test. The results show that with plasma sputtering treatment, the hydrophobic properties of the surface of wool become super hydrophobic.

Microfiltration membranes prepared from polyethersulfone powder grafted with acrylic acid by simultaneous irradiation and their pH dependence

International Nuclear Information System (INIS)

Deng Bo; Li Jingye; Hou Zhengchi; Yao Side; Shi Liuqing; Liang Guoming; Sheng Kanglong

2008-01-01

Polyethersulfone (PES) powder was grafted with acrylic acid (AAc) by simultaneous γ-ray irradiation. The kinetics of the radiation induced graft polymerization was studied and the grafted PES powder was characterized. Then, microfiltration (MF) membranes were prepared from PES-g-PAAc powder with different degrees of grafting (DG) under phase inversion method. The swelling behavior and the mean pore size of MF membranes were measured, and the filtration property was tested. The results showed that the pore size and the flux of MF membranes increased with the increase in DG. And, MF membranes' properties were dependent on the pH value

Assessment of health implications related to processing and use of natural wool insulation products.

Science.gov (United States)

Mansour, E; Loxton, C; Elias, R M; Ormondroyd, G A

2014-12-01

This paper discusses possible health implications related to dust particles released during the manufacture of sheep's wool-based non-woven insulation material. Such insulation may replace traditional synthetic insulation products used in roofs, wall cavities, etc. A review of the literature concerning organic dusts in general and sheep's wool fiber summarizes dust exposure patterns, toxicological pathways and the hazards imposed by inhalation and explosion risk. This paper highlights a need for more research in order to refrain from overgeneralizing potential pulmonary and carcinogenic risks across the industries. Variables existing between industries such as the use of different wool types, processes, and additives are shown to have varying health effects. Within the final section of the paper, the health issues raised are compared with those that have been extensively documented for the rock and glass wool industries. Copyright © 2014 Elsevier Ltd. All rights reserved.

Preparation of New Adsorbent Containing Hydroxamic Acid Groups by Electron Beam-Induced Grafting for Metal Ion Adsorption

International Nuclear Information System (INIS)

Suwanmala, Phiriyatorn; Hoshina, Hiroyuki; Seko, Noriaki; Tamada, Masao

2007-08-01

Full text: A new adsorbent containing hydroxamic acid groups was synthesized by electron beam-induced graft copolymerization of methyl acrylate (MA) onto nonwoven fabric composed of polyethylene-coated polypropylene fiber. Conversion of ester groups of the grafted copolymer into the hydroxamic groups was performed by treatment with an alkaline solution of hydroxylamine (HA). Adsorbent containing hydroxamic acid groups can adsorb 99% of UO2 2+ , 98% of V5+, 97% of Pb2+ and 96% of Al3+ at pH, 5, 4, 6, and 4, respectively, after coming into contact with 100 ppb metal solution for 24 h

Novel method for synthesis of silver nanoparticles and their application on wool

Energy Technology Data Exchange (ETDEWEB)

Boroumand, Majid Nasiri [Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Montazer, Majid [Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Simon, Frank [Leibniz-Institut für Polymerforschung Dresden e.V., Dresden (Germany); Liesiene, Jolanta [Faculty of Chemical Technology, Kaunas University of Technology, Kaunas (Lithuania); Šaponjic, Zoran [Vinča Institute of Nuclear Sciences, University of Belgrade, Belgrade (Serbia); Dutschk, Victoria, E-mail: v.dutschk@utwente.nl [Faculty of Engineering Technology, University of Twente, Enschede (Netherlands)

2015-08-15

Graphical abstract: Tentative mechanism for reduction of Ag{sup +} by polyphenols having two hydroxy groups in ortho-position – the use of silver nanoparticles and an aqueous solution of extracted dye from Pomegranate peel as a reducing agent for synthesis silver nanoparticles from silver nitrate. - Highlights: • A new method for the synthesis of silver nanoparticles suitable to impart antibacterial properties of wool fabric proposed. • Silver nanopartilces were synthesized by a biochemical reduction method. • An aqueous solution of extracted dye from Pomegranate peel was used as a reducing agent for synthesis of silver nanoparticles from silver nitrate. - Abstract: In this study, a new method for the synthesis of silver nanoparticles (AgNPs) suitable to impart antibacterial properties of wool fabric is proposed. AgNPs were synthesized by a biochemical reduction method. An aqueous solution of extracted dye from Pomegranate peel was used as a reducing agent for the synthesis of AgNPs from silver nitrate. The ratio of dye to silver nitrate concentration (R{sub Dye}/{sub Ag} = [Dye]/[AgNO{sub 3}]) is the influencing factor in the synthesis of silver nanoparticles. The nanoparticles formation was followed by UV/Vis absorption spectroscopy. The size and shape of AgNPs were studied by transmission electron microscopy (TEM). The size distribution and Zetapotential of nanoparticles were evaluated using diffraction light scattering (DLS) measurements. The antibacterial potential of biosynthesized silver nanoparticles against Escherichia coli (E. coli) was examined qualitatively and quantitatively. Kinetic analysis of the bacteria reduction using AgNPs synthesized in different way was performed. AgNPs were applied on wool fabrics by exhaustion. The changes in surface morphology of wool fibers after AgNPs loading were studied using scanning electron microscopy (SEM). The amounts of silver deposited on wool fabrics at different pH and temperature were compared applying

Novel method for synthesis of silver nanoparticles and their application on wool

International Nuclear Information System (INIS)

Boroumand, Majid Nasiri; Montazer, Majid; Simon, Frank; Liesiene, Jolanta; Šaponjic, Zoran; Dutschk, Victoria

2015-01-01

Graphical abstract: Tentative mechanism for reduction of Ag + by polyphenols having two hydroxy groups in ortho-position – the use of silver nanoparticles and an aqueous solution of extracted dye from Pomegranate peel as a reducing agent for synthesis silver nanoparticles from silver nitrate. - Highlights: • A new method for the synthesis of silver nanoparticles suitable to impart antibacterial properties of wool fabric proposed. • Silver nanopartilces were synthesized by a biochemical reduction method. • An aqueous solution of extracted dye from Pomegranate peel was used as a reducing agent for synthesis of silver nanoparticles from silver nitrate. - Abstract: In this study, a new method for the synthesis of silver nanoparticles (AgNPs) suitable to impart antibacterial properties of wool fabric is proposed. AgNPs were synthesized by a biochemical reduction method. An aqueous solution of extracted dye from Pomegranate peel was used as a reducing agent for the synthesis of AgNPs from silver nitrate. The ratio of dye to silver nitrate concentration (R Dye / Ag = [Dye]/[AgNO 3 ]) is the influencing factor in the synthesis of silver nanoparticles. The nanoparticles formation was followed by UV/Vis absorption spectroscopy. The size and shape of AgNPs were studied by transmission electron microscopy (TEM). The size distribution and Zetapotential of nanoparticles were evaluated using diffraction light scattering (DLS) measurements. The antibacterial potential of biosynthesized silver nanoparticles against Escherichia coli (E. coli) was examined qualitatively and quantitatively. Kinetic analysis of the bacteria reduction using AgNPs synthesized in different way was performed. AgNPs were applied on wool fabrics by exhaustion. The changes in surface morphology of wool fibers after AgNPs loading were studied using scanning electron microscopy (SEM). The amounts of silver deposited on wool fabrics at different pH and temperature were compared applying energy

Studies on surface graft polymerization of acrylic acid onto PTFE film by remote argon plasma initiation

International Nuclear Information System (INIS)

Wang Chen; Chen Jierong

2007-01-01

The graft polymerization of acrylic acid (AAc) was carried out onto poly(tetrafluoroethylene) (PTFE) films that had been pretreated with remote argon plasma and subsequently exposed to oxygen to create peroxides. Peroxides are known to be the species responsible for initiating the graft polymerization when PTFE reacts with AAc. We chose different parameters of remote plasma treatment to get the optimum condition for introducing maximum peroxides (2.87 x 10 -11 mol/cm 2 ) on the surface. The influence of grafted reaction conditions on the grafting degree was investigated. The maximum grafting degree was 25.2 μg/cm 2 . The surface microstructures and compositions of the AAc grafted PTFE film were characterized with the water contact angle meter, Fourier-transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). Contact angle measurements revealed that the water contact angle decreased from 108 o to 41 o and the surface free energy increased from 22.1 x 10 -5 to 62.1 x 10 -5 N cm -1 by the grafting of the AAc chains. The hydrophilicity of the PTFE film surface was greatly enhanced. The time-dependent activity of the grafted surface was better than that of the plasma treated film

Sheep Wool as a Construction Material for Energy Efficiency Improvement

Directory of Open Access Journals (Sweden)

Azra Korjenic

2015-06-01

Full Text Available The building sector is responsible for 40% of the current CO2 emissions as well as energy consumption. Sustainability and energy efficiency of buildings are currently being evaluated, not only based on thermal insulation qualities and energy demands, but also based on primary energy demand, CO2 reductions and the ecological properties of the materials used. Therefore, in order to make buildings as sustainable as possible, it is crucial to maximize the use of ecological materials. This study explores alternative usage of sheep wool as a construction material beyond its traditional application in the textile industry. Another goal of this research was to study the feasibility of replacement of commonly used thermal insulations with natural and renewable materials which have better environmental and primary energy values. Building physics, energy and environmental characteristics were evaluated and compared based on hygrothermal simulation and ecological balance methods. The observations demonstrate that sheep wool, compared with mineral wool and calcium silicate, provides comparable thermal insulation characteristics, and in some applications even reveals better performance.

Peat-based organic growbags as a solution to the mineral wool waste problem

Directory of Open Access Journals (Sweden)

O. Grunert

2008-09-01

Full Text Available The vast amount of solid waste produced each year is one of the greatest problems associated with greenhouse horticulture in some European countries. In particular, the disposal of used growing media arising from the soil-less cultivation of vegetables in mineral wool creates serious difficulties. The non-biodegradability of these mainly inorganic substrates causes environmental concern and has prompted the search for alternative growing media such as cocos derivatives, perlite and resin foam (Fytocell®. Organic substrates in combination with biodegradable material such as plastic, rope and clippings have the advantage that re-use or recycling of the waste is easier, cheaper and more environmentally friendly than for mineral wool. However, the differing physical and chemical characteristics of the alternative substrates may affect yield significantly. Substrates based respectively on peat and peat with cocos derivatives were tested against a mineral wool control for the production of tomato in three consecutive years. Both organic substrates were placed in biodegradable plastic bags. Greenhouse experiments demonstrated that plants grown in the pure peat substrate rooted more easily than plants grown in the peat-cocos substrate or mineral wool, and that they developed less blossom-end rot in both peat substrates than in mineral wool. Due to the buffering capacity of the organic substrates, the electrical conductivity of the draining water appeared to be more stable during cultivation. The total yield of tomato fruits was similar for all substrates, and no differences between substrates could be observed in the quality of the fruits produced. On the other hand, flavour tests demonstrated that plants grown on peat substrate produced more tasty fruits under certain conditions. The results of this study show that organic growbags are promising and competitive alternatives to mineral wool.

Biological influences on the quality properties of wool

African Journals Online (AJOL)

feeding and management) and the relationship between certain physical and chemical fleece and fibre properties and their ... clean yield, appearance. Presented at ..... Tender wool can be prevented by maintaining a good level of nutrition.

Determination of the fibre orientation distribution of a mineral wool network and prediction of its transverse stiffness using X-ray tomography

DEFF Research Database (Denmark)

Chapelle, Lucie; Lyckegaard, Allan; Kusano, Yukihiro

2018-01-01

A method to determine the orientation and diameter distributions of mineral wool fibre networks using X-ray tomography and image analysis is presented. The method is applied to two different types of mineral wool: glass wool and stone wool. The orientation information is obtained from...... the computation of the structure tensor, and the diameter is estimated by applying a greyscale granulometry. The results of the image analysis indicate the two types of fibres are distributed in a 2D planar arrangement with the glass wool fibres showing a higher degree of planarity than the stone wool fibres...

Superabsorbent hydrogels via graft polymerization of acrylic acid from chitosan-cellulose hybrid and their potential in controlled release of soil nutrients.

Science.gov (United States)

Essawy, Hisham A; Ghazy, Mohamed B M; El-Hai, Farag Abd; Mohamed, Magdy F

2016-08-01

Superabsorbent polymers fabricated via grafting polymerization of acrylic acid from chitosan (CTS) yields materials that suffer from poor mechanical strength. Hybridization of chitosan with cellulose (Cell) via chemical bonding using thiourea formaldehyde resin increases the flexibility of the produced hybrid (CTS/Cell). The hybridization process and post graft polymerization of acrylic acid was followed using Fourier transform infrared (FTIR). Also, the obtained structures were homogeneous and exhibited uniform surface as could be shown from imaging with scanning electron microscopy (SEM). Thus, the polymers derived from the grafting of polyacrylic acid from (CTS/Cell) gave rise to much more mechanically robust structures ((CTS/Cell)-g-PAA) that bear wide range of pH response due to presence of chitosan and polyacrylic acid in one homogeneous entity. Additionally, the obtained structures possessed greater water absorbency 390, 39.5g/g in distilled water and saline (0.9wt.% NaCl solution), respectively, and enhanced retention potential even at elevated temperatures as revealed by thermogravimetric analysis (TGA). This could be explained by the high grafting efficiency (GE%), 86.4%, and grafting yield (GY%), 750%. The new superabsorbent polymers proved to be very efficient devices for controlled release of fertilizers into the soil which expands their use in agriculture and horticultural applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Synthesis of Cotton from Tossa Jute Fiber and Comparison with Original Cotton

Directory of Open Access Journals (Sweden)

Md. Mizanur Rahman

2015-01-01

Full Text Available Cotton fibers were synthesized from tossa jute and characteristics were compared with original cotton by using FTIR and TGA. The FTIR results indicated that the peak intensity of OH group from jute cotton fibers occurred at 3336 cm−1 whereas the peak intensity of original cotton fibers occurred at 3338 cm−1. This indicated that the synthesized cotton fiber properties were very similar to the original cotton fibers. The TGA result showed that maximum rate of mass loss, the onset of decomposition, end of decomposition, and activation energy of synthesized cotton were higher than original cotton. The activation energy of jute cotton fibers was higher than the original cotton fibers.

Modification of wool protein fiber with plasma and dendrimer: Effects on dyeing with cochineal.

Science.gov (United States)

Sajed, Toktam; Haji, Aminoddin; Mehrizi, Mohammad Khajeh; Nasiri Boroumand, Majid

2018-02-01

In this study, plasma treatment and a poly(propylene imine) dendrimer were employed to improve the dyeability of wool fibers with cochineal natural dye. FESEM, EDX, AFM and FTIR techniques were employed to investigate the effects of these treatments on chemical and physical properties of wool fibers. The etching of the surface layer of wool fibers and increased roughness after plasma treatment was confirmed by FESEM and AFM images. EDX and FTIR analyses confirmed the creation of oxygen-containing groups and attachment of dendrimer molecules on wool fibers after plasma and dendrimer treatments respectively. The effects of different dyeing parameters on dye absorption and the applicability of different isotherm and kinetic models on the dyeing process were investigated. The results showed that the kinetics of absorption of cochineal on raw, plasma-treated and dendrimer-treated fibers was best fitted with the pseudo-second-order model and the isotherms of the dyeing processes followed the Freundlich model. Copyright © 2017 Elsevier B.V. All rights reserved.

Radiolytical Preparation of a Poly(Vinylbenzyl Sulfonic Acid)-Grafted FEP Membrane and Characterization as Polymer Electrolytes for Direct Methanol Fuel Cells

Energy Technology Data Exchange (ETDEWEB)

Nho, Y -C; Shin, J; Sohn, J -Y; Fei, G [Radiation Research Division for Industry and Environment, Korea Atomic Energy Research Institute, 1266 Sinjeong-dong, Jeongeup-si, Jeollabuk-do 580-185 (Korea, Republic of)

2012-09-15

In this study, a novel polymer electrolyte membrane, poly(vinylbenzyl sulfonic acid)-grafted poly(tetrafluoroethylene-co-hexafluoropropylene) (FEP-g-PVBSA), has been successfully prepared by simultaneous irradiation grafting of vinylbenzyl chloride(VBC) monomer onto a FEP film and taking subsequent chemical modification steps to modify the benzyl chloride moiety to the benzyl sulfonic acid moiety. The chemical reactions for the sulfonation were carried out via the formation of thiouronium salt with thiourea, base-catalyzed hydrolysis for the formation of thiol, and oxidation with hydrogen peroxide. Each chemical conversion process was confirmed by FTIR, elemental analysis, and SEM-EDX. A chemical stability study performed with Fenton's reagent (3% H{sub 2}O{sub 2} solution containing 4 ppm of Fe{sup 2+}) at 70 deg. C revealed that FEP-g-PVBSA has a higher chemical stability than the poly(styrene sulfonic acid)-grafted membranes (FEP-g-PSSA). An EDX analysis was also used to observe the cross-sectional distribution behaviors of the hydrophilic sulfonic acid groups and hydrophobic fluorine groups. The characteristics of an ion-exchange capacity (IEC), water and methanol uptake, methanol permeability, and proton conductivity as a function of the degree of grafting were also studied. The IECs and water uptakes of membranes with different degrees of grafting (36-102%) were measured to be in the range of 0.8-1.62 meq/g, and 10-30%, respectively. When the degree of grafting reached 60% the proton conductivity was higher than that of a Nafion (registered) 212 membrane (6.1E-02 S/cm). The methanol permeability and uptake of the FEP-g-PVBSA membrane was significantly lower than that of the Nafion (registered) 212 membrane, and even the degree of grafting reached 102%. (author)

µ-XRF Studies on the Colour Brilliance in Ancient Wool Carpets

Directory of Open Access Journals (Sweden)

Markus Meyer

2017-01-01

Full Text Available Many handmade ancient and recent oriental wool carpets show outstanding brilliance and persistence of colour that is not achieved by common industrial dyeing procedures. Anthropologists have suggested the influence of wool fermentation prior to dyeing as key technique to achieve the high dyeing quality. By means of μ-XRF elemental mapping of mordant metals we corroborate this view and show a deep and homogenous penetration of colourants into fermented wool fibres. Furthermore we are able to apply this technique and prove that the fermentation process for ancient specimens cannot be investigated by standard methods due to the lack of intact cuticle layers. This finding suggests a broad range of further investigations that will contribute to a deeper understanding of the development of traditional dyeing techniques. Spectroscopic studies add information on the oxidation states of the metal ions within the respective mordant-dye-complexes and suggest a partial charge transfer as basis for a significant colour change when Fe mordants are used.

A Conductive Porous Structured Chitosan-grafted Polyaniline Cryogel for use as a Sialic Acid Biosensor

International Nuclear Information System (INIS)

Fatoni, Amin; Numnuam, Apon; Kanatharana, Proespichaya; Limbut, Warakorn; Thavarungkul, Panote

2014-01-01

Highlights: • A novel chitosan grafted polyaniline cryogel was used as support for a highly stable and sensitive biosensor. • The use of two enzymes mediated with ferrocene showed a high selectivity for sialic acid. • The biosensor provided a rapid sialic acid detection in blood. - Abstract: A porous conductive supporting material base on chitosan grafted polyaniline (CPANI) cryogel was developed for the fabrication of a sialic acid biosensor. Two enzymes, N-acetylneuraminic acid aldolase (NAL) and pyruvate oxidase (PYO), were employed together with an electrochemical detector. The electron transfer was further enhanced by using multiwalled carbon nanotubes (MWCNTs) and mediated by ferrocene (Fc) entrapped in the cryogel pores wall. A sialic acid derived electroactive product was detected amperometrically in a flow injection system. The fabricated sialic acid biosensor provided excellent analytical performances with a wide linear range of 0.025 to 15.0 mM and a limit of detection of 18 μM. Under the low applied potential of 0.20 V versus a Ag/AgCl, common electroactive interfering compounds such as ascorbic acid, uric acid and pyruvic acid were not detected and they have no effect on the analysis of sialic acid. The fabricated sialic acid biosensor also demonstrated a high stability after up to 100 injections. The reliability of the biosensor to detect sialic acid in blood plasma was in good agreement (P > 0.05) with a standard periodic-resorcinol spectrophotometric method. This easy to prepare conductive and biocompatible porous structure should be a prospective supporting material for biosensor development

Properties of starch-polyglutamic acid (PGA) graft copolymer prepared by microwave irradiation - Fourier transform infrared spectroscopy (FTIR) and rheology studies

Science.gov (United States)

The rheological properties of waxy starch-'-polygutamic acid (PGA) graft copolymers were investigated. Grafting was confirmed by FTIR spectroscopy. The starch-PGA copolymers absorbed water and formed gels, which exhibited concentration-dependent viscoelastic solid properties. Higher starch-PGA conce...

Clinical and radiographic evaluation of citric acid-based nano hydroxyapatite composite graft in the regeneration of intrabony defects - A randomized controlled trial

Directory of Open Access Journals (Sweden)

Chaurasia Priya Dayashankar

2017-01-01

Full Text Available Background: Conventional periodontal therapy with various bone grafts has limited scope and the results are not predictable. To improve their utility, the hybridization of bioceramics and biodegradable polymers has been widely adopted to reform the mechanical properties of bone grafts. One such biodegradable polymer is POC (Poly 1,8 octanediol. Secondly, citric acid is considered as the key material in bone mineralization, which is related to the overall stability, strength and fracture resistance of bone. Hence citric acid is incorporated in a polymer and Nano hydroxyapatite to form a composite graft, for periodontal bone regeneration. This study attempts to evaluate the efficacy of citric acid based Nano-hydroxyapatite composite graft for the treatment of intrabony defects in chronic periodontitis patients over 12 months. Methods: A split mouth study, which consists of 10 systemically healthy patients, were randomly treated with Citric acid based Nano hydroxyapatite composite graft (test sites, n=18 or with Nano hydroxyapatite alone (control sites, n=15. Plaque index, gingival index, gingival bleeding index, probing pocket depth (PPD, clinical attachment level (CAL, bone probing depth (BPD and hard tissue parameters such as amount of defect fill, percentage of defect fill, and changes in alveolar crest were assessed over a period of 12 months. Statistical analysis used was student's t-test and One-Way ANOVA. Results: Both test and control sites demonstrated statistically significant reduction of PD, BPD, gain in CAL and radiographic bone fill. Nevertheless the test sites showed Statistically significant improvements in all the parameters as compared to control sites at 12 months. Conclusion: Citric acid based Nano hydroxyapatite composite graft can be considered as a newer material for periodontal regeneration.

Highly hydrophilic ultra-high molecular weight polyethylene powder and film prepared by radiation grafting of acrylic acid

Energy Technology Data Exchange (ETDEWEB)

Wang, Honglong [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Xu, Lu; Li, Rong [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Pang, Lijuan [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Hu, Jiangtao; Wang, Mouhua [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Wu, Guozhong, E-mail: wuguozhong@sinap.ac.cn [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China)

2016-09-30

Highlights: • Hydrophilic UHMWPE powder and film were obtained by γ-ray pre-irradiation grafting of AA. • A low concentration of AA solution was used for surface modification of UHMWPE. • A small grafting yield of AA sufficiently improved hydrophilicity of UHMWPE powder and film. - Abstract: The surface properties of ultra-high molecular weight polyethylene (UHMWPE) are very important for its use in engineering or composites. In this work, hydrophilic UHMWPE powder and film were prepared by γ-ray pre-irradiation grafting of acrylic acid (AA) and further neutralization with sodium hydroxide solution. Variations in the chemical structure, grafting yield and hydrophilicity were investigated and compared. FT-IR and XPS analysis results showed that AA was successfully grafted onto UHMWPE powder and film; the powder was more suitable for the grafting reaction in 1 wt% AA solution than the film. Given a dose of 300 kGy, the grafting yield of AA was ∼5.7% for the powder but ∼0.8% for the film under identical conditions. Radiation grafting of a small amount of AA significantly improved the hydrophilicity of UHMWPE. The water contact angle of the UHMWPE-g-PAA powder with a grafting yield of AA at ∼5.7% decreased from 110.2° to 68.2°. Moreover, the grafting powder (UHMWPE-g-PAA) exhibited good dispersion ability in water.

Water absorption, retention and the swelling characteristics of cassava starch grafted with polyacrylic acid

NARCIS (Netherlands)

Witono, J. R.; Noordergraaf, Inge; Heeres, H. J.; Janssen, L. P. B. M.; Heeres, Hero

2014-01-01

An important application of starch grafted with copolymers from unsaturated organic acids is the use as water absorbent. Although much research has been published in recent years, the kinetics of water absorption and the swelling behavior of starch based superabsorbents are relatively unexplored.

Ligand-functionalized degradable polyplexes formed by cationic poly(aspartic acid)-grafted chitosan-cyclodextrin conjugates

Science.gov (United States)

Song, Hai-Qing; Li, Rui-Quan; Duan, Shun; Yu, Bingran; Zhao, Hong; Chen, Da-Fu; Xu, Fu-Jian

2015-03-01

Polypeptide-based degradable polyplexes attracted considerable attention in drug delivery systems. Polysaccharides including cyclodextrin (CD), dextran, and chitosan (CS) were readily grafted with cationic poly(aspartic acid)s (PAsps). To further enhance the transfection performances of PAsp-based polyplexes, herein, different types of ligand (folic acid, FA)-functionalized degradable polyplexes were proposed based on the PAsp-grafted chitosan-cyclodextrin conjugate (CCPE), where multiple β-CDs were tied on a CS chain. The FA-functionalized CCPE (i.e., CCPE-FA) was obtained via a host-guest interaction between the CD units of CCPE and the adamantane (Ad) species of Ad-modified FA (Ad-FA). The resulting CCPE/pDNA, CCPE-FA/pDNA, and ternary CCPE-FA/CCPE/pDNA (prepared by layer-by-layer assembly) polyplexes were investigated in detail using different cell lines. The CCPE-based polyplexes displayed much higher transfection efficiencies than the CS-based polyplexes reported earlier by us. The ternary polyplexes of CCPE-FA/CCPE/pDNA produced excellent gene transfection abilities in the folate receptor (FR)-positive tumor cells. This work would provide a promising means to produce highly efficient polyplexes for future gene therapy applications.Polypeptide-based degradable polyplexes attracted considerable attention in drug delivery systems. Polysaccharides including cyclodextrin (CD), dextran, and chitosan (CS) were readily grafted with cationic poly(aspartic acid)s (PAsps). To further enhance the transfection performances of PAsp-based polyplexes, herein, different types of ligand (folic acid, FA)-functionalized degradable polyplexes were proposed based on the PAsp-grafted chitosan-cyclodextrin conjugate (CCPE), where multiple β-CDs were tied on a CS chain. The FA-functionalized CCPE (i.e., CCPE-FA) was obtained via a host-guest interaction between the CD units of CCPE and the adamantane (Ad) species of Ad-modified FA (Ad-FA). The resulting CCPE/pDNA, CCPE

A Tat-grafted anti-nucleic acid antibody acquires nuclear-localization property and a preference for TAR RNA

International Nuclear Information System (INIS)

Jeong, Jong-Geun; Kim, Dong-Sik; Kim, Yong-Sung; Kwon, Myung-Hee

2011-01-01

Highlights: → We generate ' H3 Tat-3D8' by grafting Tat 48-60 peptide to VH CDR of 3D8 scFv antibody. → H3 Tat-3D8 antibody retains nucleic acid binding and hydrolyzing activities. → H3 Tat-3D8 acquires a preference for TAR RNA structure. → Properties of Tat 48-60 is transferred to an antibody via Tat-grafting into a CDR. -- Abstract: The 3D8 single chain variable fragment (3D8 scFv) is an anti-nucleic acid antibody that can hydrolyze nucleic acids and enter the cytosol of cells without reaching the nucleus. The Tat peptide, derived from the basic region of the HIV-1 Tat protein, translocates to cell nuclei and has TAR RNA binding activity. In this study, we generated a Tat-grafted antibody ( H3 Tat-3D8) by replacing complementarity-determining region 3 (CDR3) within the VH domain of the 3D8 scFv with a Tat 48-60 peptide (GRKKRRQRRRPPQ). H3 Tat-3D8 retained the DNA-binding and DNA-hydrolyzing activity of the scFv, and translocated to the nuclei of HeLa cells and preferentially recognized TAR RNA. Thus, the properties associated with the Tat peptide were transferred to the antibody via Tat-grafting without loss of the intrinsic DNA-binding and hydrolyzing activities of the 3D8 scFv antibody.

The rotational mobility of spin labels in wool creatine depending on temperature, humidity and deformation

International Nuclear Information System (INIS)

Bobodzhanov, P.Kh.; Yusupov, I.Kh.; Marupov, R.

2001-01-01

Present article is devoted to study of rotational mobility of spin labels in wool creatine depending on temperature, humidity and deformation. The experimental data of study of structure and molecular mobility of wool creatine modified by spin labels was considered.

New membranes obtained by grafted irradiated PVDF foils

Energy Technology Data Exchange (ETDEWEB)

Mazzei, R. [Unidad de Actividades Tecnologicas y Agropecuarias, Laboratorio de Polimeros, Comision Nacional de Energia Atomica, Buenos Aires (Argentina); Universidad Tecnologica Nacional Facultad Regional, Buenos Aires (Argentina); Garcia Bermudez, G. [Gerencia de Investigacion y Aplicaciones, Laboratorio Tandar, Comision Nacional de Energia Atomica, Buenos Aires (Argentina); Escuela de Ciencia y Tecnologia, Universidad Nacional de General San Martin, Buenos Aires (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas, Buenos Aires (Argentina); Camporotondi, D.E., E-mail: camporotondi@cae.cnea.gov.ar [Unidad de Actividades Tecnologicas y Agropecuarias, Laboratorio de Polimeros, Comision Nacional de Energia Atomica, Buenos Aires (Argentina); Arbeitman, C. [Gerencia de Investigacion y Aplicaciones, Laboratorio Tandar, Comision Nacional de Energia Atomica, Buenos Aires (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas, Buenos Aires (Argentina); and others

2012-09-15

The present work describes a new method to produce membranes of poly(Acrylic-acid-Xmonomer) using the grafting procedure. PVDF foils irradiated with Ar{sup +} beam with energies between 30 and 150 keV were employed as substratum. Different combinations of monomers in water solutions were used: acrylic acid (AAc); acrylic acid-glycidyl methacrylate (AAc-GMA); acrylic acid-styrene (AAc-S), acrylic acid-N-isopropyl acrylamide (AAc-NIPAAm) and acrylic acid-N-isopropyl acrylamide-glycidyl methacrylate (AAc-NIPAAm-GMA). A large percentage of grafting results for specific values of: ion fluence and energy, AAc and sulfuric acid concentration, and different substrata PVDF polymorphous (alpha or beta). At a particular time of the grafting process, the poly(AAc-Xmonomer) membranes detach from the substratum and continue their grafting in the solution. This method is useful to produce increased replicated membranes of the irradiated original surface.

78 FR 57808 - Rules and Regulations Under the Wool Products Labeling Act of 1939

Science.gov (United States)

2013-09-20

... noted a Cashmere and Camel Hair Manufacturers Institute study finding that, between 2004 and 2009, false... wool.\\26\\ The Joint Comment, however, reported the lack of consensus in the trade regarding ``how the S... with the Wool Act, to establish a complete defense to false advertising claims under the Lanham Act as...

Activity of some nucleases of cotton sorts and species of various radiosensitivity

International Nuclear Information System (INIS)

Nazirov, N.N.; Arslanova, S.B.

1979-01-01

The activity of some nucleases under the effect of gamma rays was studied on cotton varieties and species differing in radiosensitivity. It was found that acid nuclease was more active in wild cotton forms as compared to the cultivated varieties, whereas with alkaline DNA-ase it was opposite. At the radiation dose of 30 kR the activity of alkaline DNA-ase activated in 26-chromosome wild cotton G. arboreum ssp. alfusifalium and 52-chromosome S.h.ssp.mexicanum, while the activity of acid DNA-ase somewhat decreased. Under irradiating AN-402 variety (produced from ssp. mexicanum by irradiation) the activity of alkaline DNA-ase increased noticeably when budding, whereas the activity of acid DNA-ase was at the level of control. The activity of the alkaline DNA-ase form normalized in the phase of blooming. In C-70-59 variety (G.arboreum) the activity of both DNA-ases increased after irradiation in the phase of blooming. The activity of acid DNA-ase and RNA-ase drastically activated in guza 183 (G. herbaceum) under gamma irradiation, whereas that of alkaline ones remained unchanged

Flocculation and adsorption properties of biodegradable gum-ghatti-grafted poly(acrylamide-co-methacrylic acid) hydrogels

CSIR Research Space (South Africa)

Mittal, H

2015-01-01

Full Text Available This study reports the microwave-assisted synthesis of gum-ghatti (Gg)-grafted poly(acrylamide-co-methacrylic acid) (AAm-co-MAA) hydrogels for the development of biodegradable flocculants and adsorbents. The synthesized hydrogels were characterized...

Modification of polyetherurethane for biomedical application by radiation-induced grafting. I. Grafting procedure, determination of mechanical properties, and chemical modification of grafted films

International Nuclear Information System (INIS)

Jansen, B.; Ellinghorst, G.

1985-01-01

Radiation grafting of monomers onto suitable trunk polymers is a useful tool for tailoring new polymers for special purposes. This technique has been used in the past for the development of biocompatible materials, e.g., by grafting hydrogels onto mechanically stable polymers. In this first part of our work, the radiation grafting of hydrophilic or reactive monomers onto a polyetherurethane film using the pre-swelling technique is described. Following this technique the trunk polymer was swollen in the monomer before irradiation. As monomers 2-hydroxyethyl methacrylate (HEMA), 2,3-epoxypropyl methacrylate (GMA), 2,3-dihydroxypropyl methacrylate (GOMA), and acrylamide (AAm) were used. The kinetics of the grafting reactions were examined, and the distribution of the graft component inside the trunk polymer was investigated by means of infrared (IR) spectroscopy. Surface-grafted as well as bulk- and surface-grafted products could be obtained. The mechanical behavior of the grafted films--especially in the water-swollen state--was examined and compared with that of the pure trunk polymer. In nearly all cases it was found that the tensile strength sigma B and the elongation at break epsilon R decreases as the grafting yield increases. Modification of GMA- and AAm-grafted films via chemical reactions was performed to create new functional groups of biomedical interest. In this manner a diol structure, a carboxylic acid structure, and a sulfonic acid group could be introduced in the grafted polymer. The water uptake of such modified films is increased markedly when compared with that of the unmodified samples

Magnetite nanoparticles coated glass wool for As(V) removal from drinking water

International Nuclear Information System (INIS)

Kango, Sarita; Kumar, Rajesh

2015-01-01

Arsenic (As) removal from contaminated groundwater is a key environmental concern worldwide. In this study, glass wool was coated with magnetite nanoparticles under argon gas flow and magnetite coated glass wool have been investigated for application as an adsorbent for As(V) removal from water. The adsorbent was characterized by using Scanning Electron Microscopy (SEM) and arsenic contaminated water treated with adsorbent was analyzed by Inductively Coupled Plasma Mass Spectroscopy (ICP-MS). The ICP-MS results showed that 10 g/L of adsorbent removed 99.4% of As(V) within 5 hours at pH-7 and initial arsenic concentration of 360µg/L. Adsorption kinetics data fitted well in pseudo-first-order kinetics model with high correlation coefficient (R 2 = 0.995). As magnetite nanoparticles coated glass wool showed favorable adsorption behavior for As(V), it can be a promising tool for water purification

Magnetite nanoparticles coated glass wool for As(V) removal from drinking water

Energy Technology Data Exchange (ETDEWEB)

Kango, Sarita; Kumar, Rajesh, E-mail: rajesh.kumar@juit.ac.in [Department of Physics and Materials Science, Jaypee University of Information Technology, Waknaghat, District Solan (H.P.)- 173 234 (India)

2015-08-28

Arsenic (As) removal from contaminated groundwater is a key environmental concern worldwide. In this study, glass wool was coated with magnetite nanoparticles under argon gas flow and magnetite coated glass wool have been investigated for application as an adsorbent for As(V) removal from water. The adsorbent was characterized by using Scanning Electron Microscopy (SEM) and arsenic contaminated water treated with adsorbent was analyzed by Inductively Coupled Plasma Mass Spectroscopy (ICP-MS). The ICP-MS results showed that 10 g/L of adsorbent removed 99.4% of As(V) within 5 hours at pH-7 and initial arsenic concentration of 360µg/L. Adsorption kinetics data fitted well in pseudo-first-order kinetics model with high correlation coefficient (R{sup 2} = 0.995). As magnetite nanoparticles coated glass wool showed favorable adsorption behavior for As(V), it can be a promising tool for water purification.

The effect of wool hydrolysates on squamous cell carcinoma cells in vitro. Possible implications for cancer treatment.

Directory of Open Access Journals (Sweden)

Tatsiana Damps

Full Text Available Squamous cell carcinoma of the skin is the second most common cutaneous malignancy. Despite various available treatment methods and advances in noninvasive diagnostic techniques, the incidence of metastatic cutaneous squamous cell carcinoma is rising. Deficiency in effective preventive or treatment methods of transformed keratinocytes leads to necessity of searching for new anticancer agents. The present study aims to evaluate the possibility of using wool hydrolysates as such agents. Commercially available compounds such as 5-fluorouracil, ingenol mebutate, diclofenac sodium salt were also used in this study. The process of wool degradation was based on chemical pre-activation and enzymatic digestion of wool. The effect of mentioned compounds on cell viability of squamous carcinoma cell line and healthy keratinocytes was evaluated. The obtained data show a significantly stronger effect of selected wool hydrolysates compared to commercial compounds (p<0.05 on viability of cells. The wool hydrolysates decreased squamous cell carcinoma cells viability by up to 67% comparing to untreated cells. These results indicate bioactive properties of wool hydrolysates, which affect the viability of squamous carcinoma cells and decrease their number. We hypothesize that these agents may be used topically for treatment of transformed keratinocytes in actinic keratosis and invasive squamous skin cancer in humans.

Improved biotribological properties of PEEK by photo-induced graft polymerization of acrylic acid.

Science.gov (United States)

Zhao, Xiaoduo; Xiong, Dangsheng; Wang, Kun; Wang, Nan

2017-06-01

The keys of biomaterials application in artificial joints are good hydrophilicity and wear resistance. One kind of the potential bio-implant materials is polyetheretherketone (PEEK), which has some excellent properties such as non-toxic and good biocompatibility. However, its bioinert surface and inherent chemical inertness hinder its application. In this study, we reported an efficient method for improving the surface wettability and wear resistance for PEEK, a layer of acrylic acid (AA) polymer brushes on PEEK surface was prepared by UV-initiated graft polymerization. The effects of different grafting parameters (UV-irradiation time/AA monomer solution concentration) on surface characteristics were clearly investigated, and the AA-g-PEEK specimens were examined by ATR-FTIR, static water contact angle measurements and friction tests. Our results reveal that AA can be successfully grafted onto the PEEK surface after UV irradiation, the water wettability and tribological properties of AA-g-PEEK are much better than untreated PEEK because that AA is a hydrophilic monomer, the AA layer on PEEK surface can improve its bearing capacity and reduce abrasion. This detailed understanding of the grafting parameters allows us to accurately control the experimental products, and this method of surface modification broadens the use of PEEK in orthopedic implants. Copyright © 2017 Elsevier B.V. All rights reserved.

Graft copolimerization of hydrophilic monomers onto irradiated polypropylene fibers

International Nuclear Information System (INIS)

Sundardi, F.

1978-01-01

A method of graft copolymerization of hydrophilic monomers, such as 1-vinyl-2-pyrrolidone, acrylonitrile, acrylic acid, and acrylamide, onto irradiated polypropylene fibers has been studied. γ ray as well as electron beam were employed for the irradiation processes. Graft-copolymerization kinetics and the properties of grafted fibers have been investigated. Moisture regain, dyes absorption, and melting point of the grafted fibers were found to increase with the increasing of the degree of grafting. Polypropylene for 1-vinyl-2-pyrrolidone grafted fibers showed excellent dye absorption for almost all kinds of dyes such as direct, basic, acid, reactive, disper, and naphthol dyes. However, for polypropylene acrylic acid grafted fibers, the colorfastness to washing was found to be unsatisfactory. The colorfastness to washing for polypropylene 1-vinyl-2-pyrrolidone grafted fibers was found to be fairly good for certain types of dyes such as vat and naphthol dyes. (author)

Radiation graft copolymerization of styrene with m/e and styrene with acrylic acid at highthyl methacryl dose rate

International Nuclear Information System (INIS)

Aliev, R.Eh.; Kabanov, B.Ya.

1984-01-01

Comparative investigation of radiation graft copolymerization of styrene with methyl methacrylate (MMA) and styrene with acrylic acid (AA) is carried out at considerably differing radiation dose rates. The monomer mixture was grafted to PE low density films at dose rates of 0.16, 0.25 Gy/s (1 MeV electron acceleration). The value of graft was 3-6 and 5-10%, respectively, for the styrene-MMA and styrene-AA systems. An essential difference in the dependences of the formed copolymer composition on initial monomer mixture composition is noticed. Difference in composition of graft polymers prepared at different dose rates is less for the systems with AA, than for systems with MMA. It is shown that at high dose rates in difference with low ones not only radical graft copolymerization of the styrene mixture with AA takes place, but a contribution of the graft styrene polymerization according to cation mechanism as well

Superabsorbent Prepared by Radiation Induced Graft Copolymerization of Acrylic Acid onto Cassava Starch. Chapter 18

Energy Technology Data Exchange (ETDEWEB)

Suwanmala, P.; Tangthong, T.; Hemvichian, K. [Thailand Institute of Nuclear Technology (Thailand)

2014-07-15

Superabsorbent was synthesized by radiation induced graft polymerization of acrylic acid onto cassava starch. Parameters such as the absorbed dose and the amount of monomer were investigated in order to determine the optimum conditions for the grafting polymerization. Water retention, germination percentage, and germination energy were also determined in order to evaluate the possibility of superabsorbent in agricultural applications, especially in arid regions. The graft copolymer was characterized by the Fourier transform infrared spectroscopy (FTIR). Results indicated that the sand mixed with 0.1% wt superabsorbent could absorb more water than the sand without superabsorbent. The germination energy of corn seeds mixed with 0.5% superabsorbent was obviously higher than those without superabsorbent. These experimental results showed that the superabsorbent has considerable effects on seed germination and the growth of young plants. (author)

Water absorption, retention and the swelling characteristics of cassava starch grafted with polyacrylic acid.

Science.gov (United States)

Witono, J R; Noordergraaf, I W; Heeres, H J; Janssen, L P B M

2014-03-15

An important application of starch grafted with copolymers from unsaturated organic acids is the use as water absorbent. Although much research has been published in recent years, the kinetics of water absorption and the swelling behavior of starch based superabsorbents are relatively unexplored. Also, water retention under mechanical strain is usually not reported. Cassava starch was used since it has considerable economic potential in Asia. The gelatinized starch was grafted with acrylic acid and Fenton's initiator and crosslinked with N,N'-methylenebisacrylamide (MBAM). Besides a good initial absorption capacity, the product could retain up to 63 g H2O/g under severe suction. The material thus combines a good absorption capacity with sufficient gel strength. The mathematical analysis of the absorption kinetics shows that at conditions of practical interest, the rate of water penetration into the gel is determined by polymer chain relaxations and not by osmotic driven diffusion. Copyright © 2013 Elsevier Ltd. All rights reserved.

Identification of candidate genes from the SAD gene family in cotton for determination of cottonseed oil composition.

Science.gov (United States)

Shang, Xiaoguang; Cheng, Chaoze; Ding, Jian; Guo, Wangzhen

2017-02-01

Cotton is an economically important crop grown for natural fiber and seed oil production. Cottonseed oil ranks third after soybean oil and colza oil in terms of edible oilseed tonnage worldwide. The fatty acid composition of cottonseed oil determines its industrial application and nutritional values. However, little progress has been made in understanding cottonseed oil biogenesis. Stearoyl-acyl carrier protein desaturase (SAD), the only known enzyme to convert saturated fatty acids into unsaturated fatty acids in plants, plays key roles in determining the fatty acid composition of cottonseed oil. In this study, we identified 9, 9, 18 and 19 SAD genes in the genomes of four sequenced cotton species: diploid Gossypium raimondii (D 5 ), G. arboreum (A 2 ), tetraploid G. hirsutum acc. TM-1 (AD 1 ) and G. barbadense cv. Xinhai21 (AD 2 ), respectively. Bioinformatic and phylogenetic analyses revealed that cotton SADs can be classified into two classes. Expression patterns showed developmental and spatial regulation of SADs in cotton. GhSAD2 and GhSAD4 were preferentially expressed in developing ovules 20-35 days post-anthesis, and significantly different expression patterns were found between high-oil and low-oil cotton cultivars, implying these two genes could be involved in cottonseed oil biogenesis. Association analysis further confirmed that GhSAD4-At expression was closely related to the oleic acid (O) content, linoleic acid (L) content and O/L value in cottonseed, implying GhSAD4 plays an important role in cottonseed oil composition. This study brings new perspectives for integrated genome-wide identification of SADs in cotton and provides references for the genetic improvement of cottonseed oil.

A novel fibrin gel derived from hyaluronic acid-grafted fibrinogen

Energy Technology Data Exchange (ETDEWEB)

Yang, Chiung L; Chen, Hui W; Wang, Tzu C; Wang, Yng J, E-mail: wang@ym.edu.tw [Institute of Biomedical Engineering, National Yang Ming University, No. 155, Sec. 2, Li-Nung St., Shih-Pai, Taipei, Taiwan 112 (China)

2011-04-15

Fibrinogen is a major plasma protein that forms a three-dimensional fibrin gel upon being activated by thrombin. In this study, we report the synthesis and potential applications of hybrid molecules composed of fibrinogen coupled to the reducing ends of short-chain hyaluronic acids (sHAs) by reductive amination. The grafting of sHAs to fibrinogen was verified by analyzing particle size, zeta potential and gel-electrophoretic mobility of the hybrid molecules. The sHA-fibrinogen hybrid molecules with graft ratios (sHA/fibrinogen) of up to 6.5 retained the ability to form gels in response to thrombin activation. The sHA-fibrin gels were transparent in appearance and exhibited high water content, which were characteristics distinct from those of gels formed by mixtures of sHAs and fibrinogen. The potential applications of the sHA-fibrin gels were evaluated. The sHA-fibrinogen gel with a graft ratio of 3.6 (S3.6F) was examined for its ability to encapsulate and support the differentiation of ATDC5 chondrocyte-like cells. Compared with the fibrinogen-formed gel, cells cultured in the S3.6F gel exhibited increased lacunae formation; moreover, the abundance of cartilaginous extracellular matrix molecules and the expression of chondrocyte marker genes, such as aggrecan, collagen II and Sox9, were also significantly increased. Our data suggest that the three-dimensional gel formed by the sHA-fibrinogen hybrid is a better support than the fibrin gel for chondrogenesis induction.

A novel fibrin gel derived from hyaluronic acid-grafted fibrinogen

International Nuclear Information System (INIS)

Yang, Chiung L; Chen, Hui W; Wang, Tzu C; Wang, Yng J

2011-01-01

Fibrinogen is a major plasma protein that forms a three-dimensional fibrin gel upon being activated by thrombin. In this study, we report the synthesis and potential applications of hybrid molecules composed of fibrinogen coupled to the reducing ends of short-chain hyaluronic acids (sHAs) by reductive amination. The grafting of sHAs to fibrinogen was verified by analyzing particle size, zeta potential and gel-electrophoretic mobility of the hybrid molecules. The sHA-fibrinogen hybrid molecules with graft ratios (sHA/fibrinogen) of up to 6.5 retained the ability to form gels in response to thrombin activation. The sHA-fibrin gels were transparent in appearance and exhibited high water content, which were characteristics distinct from those of gels formed by mixtures of sHAs and fibrinogen. The potential applications of the sHA-fibrin gels were evaluated. The sHA-fibrinogen gel with a graft ratio of 3.6 (S3.6F) was examined for its ability to encapsulate and support the differentiation of ATDC5 chondrocyte-like cells. Compared with the fibrinogen-formed gel, cells cultured in the S3.6F gel exhibited increased lacunae formation; moreover, the abundance of cartilaginous extracellular matrix molecules and the expression of chondrocyte marker genes, such as aggrecan, collagen II and Sox9, were also significantly increased. Our data suggest that the three-dimensional gel formed by the sHA-fibrinogen hybrid is a better support than the fibrin gel for chondrogenesis induction.

Surface modification of calcium hydroxyapatite by grafting of etidronic acid

Science.gov (United States)

Othmani, Masseoud; Aissa, Abdallah; Bac, Christophe Goze; Rachdi, Férid; Debbabi, Mongi

2013-06-01

The surface of prepared calcium hydroxyapatite CaHAp has been modified by grafting the etidronic acid (ETD). For that purpose, CaHAp powders have been suspended in an aqueous etidronate solution with different concentrations. The obtained composites CaHAp-(ETD) were characterized by TEM and AFM techniques to determinate morphological properties and were also characterized by XRD, IR, NMR and chemical and thermal analysis to determinate their physico-chemical properties and essentially the nature of the interaction between the inorganic support and the grafted organic ETD. After reaction with ETD, XRD powder analysis shows that the apatitic structure remains unchanged with slight affectation of its crystallinity. The presence of etidronate fragment bounded to hydroxyapatite was confirmed by IR and solid-state NMR spectroscopy. TEM and AFM techniques indicate that the presence of etidronate changes the morphology of the particles. Basing on the obtained results, a reactional mechanism was proposed to explain the formation of covalent Casbnd Osbnd Porg bonds on the hydroxyapatite surface between the superficial hydroxyl groups (tbnd Casbnd OH) of the apatite and phosphonate group (Psbnd OH) of etidronate.

Nitrogen nutrition in cotton and control strategies for greenhouse gas emissions: a review.

Science.gov (United States)

Khan, Aziz; Tan, Daniel Kean Yuen; Munsif, Fazal; Afridi, Muhammad Zahir; Shah, Farooq; Wei, Fan; Fahad, Shah; Zhou, Ruiyang

2017-10-01

Cotton (Gossypium hirustum L.) is grown globally as a major source of natural fiber. Nitrogen (N) management is cumbersome in cotton production systems; it has more impacts on yield, maturity, and lint quality of a cotton crop than other primary plant nutrient. Application and production of N fertilizers consume large amounts of energy, and excess application can cause environmental concerns, i.e., nitrate in ground water, and the production of nitrous oxide a highly potent greenhouse gas (GHG) to the atmosphere, which is a global concern. Therefore, improving nitrogen use efficiency (NUE) of cotton plant is critical in this context. Slow-release fertilizers (e.g., polymer-coated urea) have the potential to increase cotton yield and reduce environmental pollution due to more efficient use of nutrients. Limited literature is available on the mitigation of GHG emissions for cotton production. Therefore, this review focuses on the role of N fertilization, in cotton growth and GHG emission management strategies, and will assess, justify, and organize the researchable priorities. Nitrate and ammonium nitrogen are essential nutrients for successful crop production. Ammonia (NH 3 ) is a central intermediate in plant N metabolism. NH 3 is assimilated in cotton by the mediation of glutamine synthetase, glutamine (z-) oxoglutarate amino-transferase enzyme systems in two steps: the first step requires adenosine triphosphate (ATP) to add NH 3 to glutamate to form glutamine (Gln), and the second step transfers the NH 3 from glutamine (Gln) to α-ketoglutarate to form two glutamates. Once NH 3 has been incorporated into glutamate, it can be transferred to other carbon skeletons by various transaminases to form additional amino acids. The glutamate and glutamine formed can rapidly be used for the synthesis of low-molecular-weight organic N compounds (LMWONCs) such as amides, amino acids, ureides, amines, and peptides that are further synthesized into high-molecular-weight organic

First detection of an NSAID, flunixin, in sheep's wool using GC-MS

Energy Technology Data Exchange (ETDEWEB)

Richards, Ngaio, E-mail: ngaio.richards@anglia.ac.uk [Life Sciences, Anglia Ruskin University, East Road, Cambridge, CB1 1PT (United Kingdom); Hall, Sarah [Life Sciences, Anglia Ruskin University, East Road, Cambridge, CB1 1PT (United Kingdom); Scott, Karen [Forensic Medicine and Science, University of Glasgow, Glasgow G12 8QQ (United Kingdom); Harrison, Nancy [Life Sciences, Anglia Ruskin University, East Road, Cambridge, CB1 1PT (United Kingdom)

2011-05-15

Exposure to the nonsteroidal anti-inflammatory drug (NSAID) diclofenac resulted in the near extinction of three species of Gyps vultures on the Indian subcontinent. Other NSAIDs present in the environment, including flunixin, may pose a similar risk. In the course of a study to determine the feasibility of detecting NSAIDs in keratinous matrices (i.e., hair, nails and feathers) using GC-MS, wool opportunistically collected from a sheep treated with flunixin was analysed for residues. Flunixin was detected qualitatively in external wool wash and extract samples. While residues of veterinary agents and pesticides have previously been found in sheep's wool, our preliminary investigation provides the first instance of an NSAID being detected in this matrix. Here we provide the sample preparation methods and GC-MS parameters used to enable further refinement as part of ongoing conservation and consumer quality control measures. - Highlights: > In this study we qualitatively detected the NSAID flunixin in sheep's wool using GC-MS. > Potential applications of this technique to the conservation of avian scavengers are outlined. > The quantitative and confirmatory steps required to fully validate the method are also provided. - This is the first time that an NSAID has been investigated or detected in sheep's wool. As such, it details a novel exposure pathway for scavenging species in the environment and offers a potential tool for future monitoring effort in vulture conservation.

Assembly of laboratory line for nuclear fuel reprocessing

International Nuclear Information System (INIS)

Fidler, J.; Chotivka, V.

1979-01-01

The dismantling of a laboratory line for spent fuel reprocessing after the termination of the research programme and the procedures for hot and semi-hot cell decontamination are described. The equipment was mostly disassembled in smaller parts which were then decontaminated by wiping them with cotton wool soaked in detergent and citric acid, varnished with two-component epoxi varnish, wrapped into multiple polyethylene foils, sealed in PVC bags and thus ready for transport. (B.S.)

[Rhinitis and asthma related to cotton dust exposure in apprentices in the clothing industry].

Science.gov (United States)

Chaari, N; Amri, C; Khalfallah, T; Alaya, A; Abdallah, B; Harzallah, L; Henchi, M-A; Bchir, N; Kamel, A; Akrout, M

2009-01-01

Respiratory allergies are the most common occupational diseases in the world. The aim of this study was to determine the prevalence of rhinitis and asthma among apprentices exposed to cotton dust in the clothing industry and to describe their epidemiologic and clinical profiles. We carried out a descriptive study of 600 apprentices in a textile and clothing vocational training centre in the Monastir area. The investigation comprised a questionnaire exploring risk factors and symptoms appearing during their training. Subjects who developed allergic respiratory symptoms at the work-place underwent a clinical examination, rhinomanometry and investigation of their allergic status and respiratory function. One hundred twenty apprentices (20%) developed allergic respiratory reactions due to exposure to textile dust (exclusively cotton) during their training, with a positive withdrawal-re-exposure test. Conjunctivitis (14.3%) and rhinitis (8.5%) were the most frequent allergic symptoms. Twenty eight apprentices (4.6%) presented symptoms of asthma. Rhinitis was associated with asthma in 45% of cases. Two cases of asthma were diagnosed clinically at the work-place following their exposure to textile dust. The prick test performed in 120 symptomatic apprentices was positive in 41.6% of cases. There was sensitization to pollens in 29 cases and to dermatophagoides in 13 cases. Cotton and wool allergy was noted in two cases. Allergic symptoms developing during the training were significantly more frequent in the atopic group, and they varied according to the intensity of textile dust exposure. In the textile and clothing industry the frequency of respiratory disorders caused by allergens remains high, especially in atopic apprentices who constitute a population at high risk.

ENVIRONMENTAL ASPECTS OF USE, DEVELOPMENT AND DISPOSAL OF MINERAL WOOL IN THE CONTEXT OF ENVIRONMENTAL RESOURCES POLLUTION BY WASTE RETARDATION

Directory of Open Access Journals (Sweden)

Dorota Nowak

2014-10-01

Full Text Available In this study presents the environmental aspects of the use, management and disposal of mineral wool. Fiber structure makes that wool products have many unique properties enabling them to be versatile. With all the advantages of mineral wool is one very significant drawback - does not decompose. From the point of view of slowing (retardation transformation of environmental resources, the introduction of mineral wool to crops under glass, in a very much reduced use of peatlands, which for reasons of natural resources are extremely important. On the other hand, problems of rational use of mineral wool already postconsumer caused among others formation of "wild dumps" and thus transforming the landscape, and, due to their characteristics (respirable fibers, the risk to health. Manufacture of asbestiform can cause ecological consequences within almost all elements of the environment. Therefore, the overall assessment of the impact in this case, mineral wool on the environment would need to be so. "Life cycle assessment" - called the method of LCA (Life Cycle Assessmentwhich is commonly called the "cradle to grave" - that is, from extraction of raw materials, through processing, exploitation, to the storage of waste. Therefore, the responsibility for the redevelopment of the post-production of mineral wool should lie with the producer of wool. These issues are the subject of discussion in this study.

New membranes obtained by grafted irradiated PVDF foils

International Nuclear Information System (INIS)

Mazzei, R.; García Bermúdez, G.; Camporotondi, D.E.; Arbeitman, C.

2012-01-01

The present work describes a new method to produce membranes of poly(Acrylic-acid-Xmonomer) using the grafting procedure. PVDF foils irradiated with Ar + beam with energies between 30 and 150 keV were employed as substratum. Different combinations of monomers in water solutions were used: acrylic acid (AAc); acrylic acid–glycidyl methacrylate (AAc–GMA); acrylic acid–styrene (AAc–S), acrylic acid-N-isopropyl acrylamide (AAc–NIPAAm) and acrylic acid-N-isopropyl acrylamide–glycidyl methacrylate (AAc-NIPAAm–GMA). A large percentage of grafting results for specific values of: ion fluence and energy, AAc and sulfuric acid concentration, and different substrata PVDF polymorphous (alpha or beta). At a particular time of the grafting process, the poly(AAc-Xmonomer) membranes detach from the substratum and continue their grafting in the solution. This method is useful to produce increased replicated membranes of the irradiated original surface.

Lignocellulosic Composites Prepared Utilizing Aqueous Alkaline/Urea Solutions with Cold Temperatures

Directory of Open Access Journals (Sweden)

Brent Tisserat

2018-01-01

Full Text Available Lignocellulosic composites (LCs were fabricated by partially dissolving cotton to create a matrix that was reinforced with osage orange wood (OOW particles and/or blue agave fibers (AF. LCs were composed of 15–35% cotton matrix and 65–85% OWW/AF reinforcement. The matrix was produced by soaking cotton wool in a cold aqueous alkaline/urea solvent and was stirred for 15 minutes at 350 rpm to create a viscous gel. The gel was then reinforced with lignocellulosic components, mixed, and then pressed into a panel mold. LC panels were soaked in water to remove the aqueous solvent and then oven dried to obtain the final LC product. Several factors involved in the preparation of these LCs were examined including reaction temperatures (−5 to −15°C, matrix concentration (15–35% cotton, aqueous solvent volume (45–105 ml/panel, and the effectiveness of employing various aqueous solvent formulations. The mechanical properties of LCs were determined and reported. Conversion of the cotton into a suitable viscous gel was critical in order to obtain LCs that exhibited high mechanical properties. LCs with the highest mechanical properties were obtained when the cotton wools were subjected to a 4.6% LiOH/15% urea solvent at −12.5°C using an aqueous solvent volume of 60 ml/panel. Cotton wool subjected to excessive cold alkaline solvents volumes resulted in irreversible cellulose breakdown and a resultant LC that exhibited poor mechanical properties.

Structural coloration of chitosan-cationized cotton fabric using photonic crystals

OpenAIRE

Yavuz, Gonul; Zille, Andrea; Seventekin, N.; Souto, A. Pedro

2017-01-01

Abstract. In this work, poly (styrene-methyl methacrylate-acrylic acid) P(St-MMA-AA) composite nanospheres were deposited onto chitosan-cationized woven cotton fabrics followed by a second layer of chitosan. The deposited photonic crystals (PCs) on the fabrics were evaluated for coating efficiency and resistance, chemical analysis and color variation by optical and SEM microscopy, ATR-FTIR, diffuse reflectance spectroscopy and washing fastness. Chitosan deposition on cotton fab...

Improved homopolymer separation to enable the application of H-1 NMR and HPLC for the determination of the reaction parameters of the graft copolymerization of acrylic acid onto starch

NARCIS (Netherlands)

Witono, Judy R.; Marsman, Jan Henk; Noordergraaf, Inge-Willem; Heeres, Hero J.; Janssen, Leon P. B. M.

2013-01-01

Graft copolymers of starch with acrylic acid are a promising green, bio based material with many potential applications. The grafting of acrylic acid onto cassava starch in an aqueous medium initiated by Fenton's reagent has been studied. Common grafting result parameters are add-on (yield) and

In vitro release studies of vitamin B12 from poly N-vinyl pyrrolidone /starch hydrogels grafted with acrylic acid synthesized by gamma radiation

International Nuclear Information System (INIS)

Eid, M.

2008-01-01

Co-polymeric hydrogels containing N-vinyl pyrrolidone and starch grafted with acrylic acid were synthesized by gamma radiation. Their gel contents, grafting process and swelling were evaluated. The gels were also characterized by thermal gravimetric analysis. The gel content found to be increase with increasing the irradiation dose up to 50 kGy then decrease. The grafting percent increase by increasing the percentage of acrylic acid in the grafted hydrogels. The thermal stability and the rate of the thermal decomposition showed to be changed according to the different composition of the hydrogels. It also showed a decrease in the maximum rate of the thermal decomposition by the increasing of the irradiation dose from 20 to 30 kGy and increases by increasing the irradiation dose from 30 to 70 kGy. The hydrogels loaded with vitamin B 12 as drug model, demonstrated a decrease release in acidic medium than the neutral one

Measured anisotropic air flow resistivity and sound attenuation of glass wool

DEFF Research Database (Denmark)

Tarnow, Viggo

2002-01-01

Department of Mechanical Engineering, Technical University of Denmark, Bygning 358, DK 2800 Lyngby, Denmark The air flow resistivity of glass wool has been measured in different directions. The glass wool was delivered from the manufacturer as slabs measuring 100×600×900 mm3, where the surface 600...... 7.75 kPa s m**2. A formula for prediction of resistivity for other densities is given. By comparing measured values of sound attenuation with results calculated from resistivity data, it is demonstrated that the measured attenuation can be predicted in a simple manner. ©2002 Acoustical Society...

Preparation of the copolymer of acrylic acid and acrylamide grafted onto polyethylene and its complexation with samarium ion

International Nuclear Information System (INIS)

Kido, Junji; Akiba, Hideto; Nishide, Hiroyuki; Tsuchida, Eishun; Omichi, Hideki; Okamoto, Jiro.

1986-01-01

Acrylic acid (AA) and acrylamide (AAm) were graft-copolymerized onto polyethylene (PE) powder by the pre-irradiation method. Complex formation constants of Sm ion with the PE powder grafted with both AA and AAm (PE-g-(AA-co-AAm)) were larger than those with the PE powder grafted with AA (PE-g-AA). Sm ion was efficiently separated from the solution containing both Sm ion and a transition metal ion such as Cu ion. Even after the γ-ray irradiation on PE-g-(AA-co-AAm) and PE-g-AA, the adsorption did not decrease. (author)

Study of color parameters of light exposed and light exposed wool fabrics dyed with 1:1 chromium (III) based complex dyes

International Nuclear Information System (INIS)

Kausar, N.; Ahmad, M.A.; Wahab, M.A.

2009-01-01

Derivatives of a-amino benzoic acid (anthranilic acid) were synthesized using 1-naphthol-3,6-disulfonic acid, 1-Naphthol-8 amino-3, 6-di-sulfonic acid; 1-naphthol-3-sulfonic acid, 6-methylamino-1-naphthol-3-sulfonic acid or 1-naphthol-3-sulfonic acid, 6-phenylamino-l-naphthol-3-sulfonic acid as a coupling component. These derivatives were used to synthesize chromium (Ill) complexes. After isolation, these complexes were applied on pure wool fabric by exhaust process to evaluate hue, wash fastness and light fastness properties. The complexes delivered a change in color equivalent to gray scale step 3/5 to 4/5 for wash fastness test. During the study of light fastness, it was monitored that the hue of dyed fabrics enhanced after exposing them to Light. (author)

OPERATING STABILITY OF MINERAL WOOL PRODUCTS

Directory of Open Access Journals (Sweden)

Perfilov Vladimir Aleksandrovich

2016-03-01

Full Text Available Creating an effective insulation envelope of the building is possible only using high-quality materials, preserving their characteristics both in the early stages of operation, and for the whole billing period. It is an important opportunity to assess the thermal insulation properties and predict its changes over time directly in the conditions of the construction site. The products based on mineral fibers (rock and glass wool, basalt fiber are the most widely used type of insulating materials in the domestic construction. Therefore, the operational stability valuation methods must be primarily created for this group of products. The methodology for assessing the thermal insulation properties includes two main components: testing equipment and methodology for assessing the operational stability. The authors tested the methodology of the accelerated testing and prediction of durability for mineral wool products of laminated, corrugated and volume-oriented structures. The test results give good convergence with the methods recommended by the building regulations. Application of thermal insulation materials are an effective way to form the thermal envelope of the building, reducing energy costs and increasing the durability of building structures. The material properties are determined by their structure, which is formed during the technological impacts.

Phosphate functionalized and lactic acid containing graft copolymer: synthesis and evaluation as biomaterial for bone tissue engineering applications.

Science.gov (United States)

Datta, Pallab; Chatterjee, Jyotirmoy; Dhara, Santanu

2013-01-01

Polyvinyl alcohol (PVA) and polylactic acids (PLA) are biocompatible materials possessing some inherent contrasting limitations which have reduced the scope of their individual applicability. Specifically, overcoming strong hydrophobicity and introducing chemical groups for biofunctionalization are unmet challenges for PLA whilst chemical endeavors to render adequate aqueous stability and cell adhesion properties to PVA have not produced completely intended results. Objective of the present work is to explore synthesis of a graft polymer as an approach towards coupling biofunctional groups with PLA materials. In a two-step reaction, PPVA (phosphorylated polyvinyl alcohol or PVA pre-functionalized with phosphate) is esterified with lactic acid followed by polymerization into PLA in presence of stannous chloride as catalyst to obtain phosphorylated polyvinyl alcohol-graft-polylactic acid (PPVA-g-LA) copolymer. Product is characterized by nuclear magnetic resonance, X-ray diffraction, and thermogravimetric analysis. PPVA-g-LA shows an increase in uniaxial elongation compared to parent PPVA under condition of tensile loading. The graft copolymer also exhibits higher water contact angles compared to PPVA, but a more hydrophilic surface compared to PLA. Culture of MG-63 cells on solvent cast films of polymers demonstrates that PPVA-g-LA as a cell substrate can significantly (p acid-based biomaterials with subsequent improvement in cell response on the polymers. In this attempt, it also affords materials with tunable surface or bulk properties of relevance for tissue engineering applications.

Grafting of activated carbon cloths for selective adsorption

Energy Technology Data Exchange (ETDEWEB)

Gineys, M.; Benoit, R.; Cohaut, N.; Béguin, F.; Delpeux-Ouldriane, S., E-mail: delpeux@cnrs-orleans.fr

2016-05-01

Graphical abstract: - Highlights: • A controlled grafting of carboxylic functions on activated carbon fibers. • The carbon material nanotextural properties preservation after grafting. • An identification of the grafting mechanism through ToF SIMS analysis. • A chemical mapping of the grafted surface using ToF SIMS technique and imaging. - Abstract: Chemical functionalization of an activated carbon cloth with 3-aminophthalic acid and 4-aminobenzoic acid groups by the in situ formation of the corresponding diazonium salt in aqueous acidic solution is reported. The nature and amount of selected functions on an activated carbon surface, in particular the grafted density, were determined by potentiometric titration, elemental analysis and X-ray photoelectron spectroscopy (XPS). The nanotextural properties of the modified carbon were explored by gas adsorption. Functionalized activated carbon cloth was obtained at a discrete grafting level while preserving interesting textural properties and a large porous volume. Finally, the grafting homogeneity of the carbon surface and the nature of the chemical bonding were investigated using Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) technique.

Graft Loss Due to Percutaneous Sclerotherapy of a Lymphocele Using Acetic Acid After Renal Transplantation

International Nuclear Information System (INIS)

Adani, Gian Luigi; Baccarani, Umberto; Bresadola, Vittorio; Lorenzin, Dario; Montanaro, Domenico; Risaliti, Andrea; Terrosu, Giovanni; Sponza, Massimo; Bresadola, Fabrizio

2005-01-01

Development of lymphoceles after renal transplantation is a well-described complication that occurs in up to 40% of recipients. The gold standard approach for the treatment of symptomatic cases is not well defined yet. Management options include simple aspiration, marsupialization by a laparotomy or laparoscopy, and percutaneous sclerotherapy using different chemical agents. Those approaches can be associated, and they depend on type, dimension, and localization of the lymphocele. Percutaneous sclerotherapy is considered to be less invasive than the surgical approach; it can be used safely and effectively, with low morbidity, in huge, rapidly accumulating lymphoceles. Moreover, this approach is highly successful, and the complication rate is acceptable; the major drawback is a recurrence rate close to 20%. We herewith report a renal transplant case in which the patient developed a symptomatic lymphocele that was initially treated by ultrasound-guided percutaneous sclerotherapy with ethanol and thereafter using acetic acid for early recurrence. A few hours after injection of acetic acid in the lymphatic cavity, the patient started to complain of acute pain localized to the renal graft and fever. An ultrasound of the abdomen revealed thrombosis of the renal vein and artery. The patient was immediately taken to the operating room, where the diagnosis of vascular thrombosis was confirmed and the graft was urgently explanted. In conclusion, we strongly suggest avoiding the use of acetic acid as a slerosating agent for the percutaneous treatment of post-renal transplant lymphocele because, based on our experience, it could be complicated by vascular thrombosis of the kidney, ending in graft loss

Effect of chitosan on resist printing of cotton fabrics with reactive dyes

African Journals Online (AJOL)

The concentration of chitosan, types of resist agent, curing temperature and curing time were varied to determine their effects on resist-printed cotton fabrics. An optimal chitosan concentration of 1.6% resulted in the greatest resist effect on printed cotton fabrics. For mixtures, a 6:4 ratio of citric acid : chitosan and an 8:2 ...

A deterministic computer simulation model of life-cycle lamb and wool production.

Science.gov (United States)

Wang, C T; Dickerson, G E

1991-11-01

A deterministic mathematical computer model was developed to simulate effects on life-cycle efficiency of lamb and wool production from genetic improvement of performance traits under alternative management systems. Genetic input parameters can be varied for age at puberty, length of anestrus, fertility, precocity of fertility, number born, milk yield, mortality, growth rate, body fat, and wool growth. Management options include mating systems, lambing intervals, feeding levels, creep feeding, weaning age, marketing age or weight, and culling policy. Simulated growth of animals is linear from birth to inflection point, then slows asymptotically to specified mature empty BW and fat content when nutrition is not limiting. The ME intake requirement to maintain normal condition is calculated daily or weekly for maintenance, protein and fat deposition, wool growth, gestation, and lactation. Simulated feed intake is the minimum of availability, DM physical limit, or ME physiological limit. Tissue catabolism occurs when intake is below the requirement for essential functions. Mortality increases when BW is depressed. Equations developed for calculations of biological functions were validated with published and unpublished experimental data. Lifetime totals are accumulated for TDN, DM, and protein intake and for market lamb equivalent output values of empty body or carcass lean and wool from both lambs and ewes. These measures of efficiency for combinations of genetic, management, and marketing variables can provide the relative economic weighting of traits needed to derive optimal criteria for genetic selection among and within breeds under defined industry production systems.

Phosphorus metabolic disorder of Guizhou semi-fine wool sheep.

Directory of Open Access Journals (Sweden)

Xiaoyun Shen

Full Text Available Guizhou semi-fine wool sheep are affected by a disease, characterized by emaciation, lameness, stiffness in the gait, enlargement of the costochondral junctions, and abnormal curvature in the long bones. The objective of this study was to determine possible relationships between the disease and mineral deficiencies. Samples of tissue and blood were collected from affected and unaffected sheep. Samples of soil and forage were collected from affected and unaffected areas. The samples were used for biochemical analyses and mineral nutrient measurements. Results showed that phosphorus (P concentrations in forage samples from affected areas were significantly lower than those from unaffected areas (P < 0.01 and the mean ratio of calcium (Ca to P in the affected forage was 12:1. Meanwhile, P concentrations of blood, bone, tooth, and wool from the affected sheep were also significantly lower than those from the unaffected group (P < 0.01. Serum P levels of the affected animals were much lower than those of the unaffected ones, whereas serum alkaline phosphatase levels from the affected were significantly higher than those from the unaffected (P < 0.01. Inorganic P levels of the affected sheep were about half of those in the control group. Oral administration of disodium hydrogen phosphate prevented and cured the disease. The study clearly demonstrated that the disease of Guizhou semi-fine wool sheep was mainly caused by the P deficiency in forage, as a result of fenced pasture and animal habitat fragmentation.

Durable antibacterial and cross-linking cotton with colloidal silver nanoparticles and butane tetracarboxylic acid without yellowing.

Science.gov (United States)

Montazer, Majid; Alimohammadi, Farbod; Shamei, Ali; Rahimi, Mohammad Karim

2012-01-01

Colloidal nano silver was applied on the surface of cotton fabric and stabilized using 1,2,3,4-butanetetracarboxylic acid (BTCA). The two properties of antimicrobial activity and resistance against creasing were imparted to the samples of fabric as a result of the treatment with silver nano colloid and BTCA. The antimicrobial property of samples was evaluated using two pathogenic bacteria including Escherichia coli and Staphylococcus aureus as outstanding barometers in this field. The durability of applied nanoparticles, color variation, wettability and wrinkle recovery angle of the treated samples were investigated employing related credible standards. The presence of nano silver particles on the surface of treated cotton fabric was proved using EDS spectrum as well as the SEM images. Furthermore, the creation of cross-links was confirmed by the means of both ATR-FTIR and Raman spectra. In conclusion, it was observed that BTCA plays a prominent role in stabilizing silver nanoparticle. Besides, Wettability and winkle recovery angle of finished samples decreased and increased, respectively. In addition, it is noteworthy that no obvious color variation was observed. Copyright © 2011 Elsevier B.V. All rights reserved.

RADIOCHEMICAL YIELDS OF GRAFT POLYMERIZATION REACTIONS OF CELLULOSE

Energy Technology Data Exchange (ETDEWEB)

Arthur, Jr, J C; Blouin, F A

1963-12-15

The preparation of radioinduced graft polymers of cotton cellulose, while retaining the fibrous nature and high molecular weight of the cellulose, depended primarily on the radiochemical yields of cellulose reactions and of graft polymerization reactions. Yields of the initial major molecular changes in cellulosic polymer indicated that, in the case of scission of the molecule and carboxyl group formation, chain reactions were not initiated by radiation; however, in the case of carbonyl group formation chain reactions were initiated but quickly terminated. Generally, experimental procedures, used in graft polymerization reactions, were: simultaneous irradiation reactions, that is, application of monomers or solutions of monomers to cellulose or chemically modified celluloses, then irradiation; and post-irradiation reactions, that is, irradiation of cellulose or chemically modified celluloses, then after removal from the field of radiation, contacting the irradiated cellulose with monomer. Some of the most important factors influencing the radiochemical yields of graft polymerization reactions, of styrene and acrylonitrile onto cellulose were: concentration of monomer in treating solution; solvent; ratio of monomer solution to cellulose; prior chemical modification of cellulose; and absence of oxygen, particularly in post-irradiation reactions. Experimental data are presented, and the direct and indirect effects of Co/sup 60/ gamma radiation on these reactions are discussed. (auth)

Antibacterial Dyeing of Wool with Natural Cationic Dye Using Metal Mordants

Directory of Open Access Journals (Sweden)

Aminoddin HAJI

2012-09-01

Full Text Available In this study, Berberine colorant extracted from berberis vulgaris root was applied on wool fiber using alum (aluminum potassium sulfate, copper sulfate and potassium dichromate as mordant. The effect of treatment variables such as amount of mordant, time and temperature on the color strength of dyed fibers was examined. The fastness properties of dyed wool against washing, light and wet rubbing were evaluated. the use of metal mordants increased the color strength of the dyed goods. Increase in dyeing time and temperature caused deeper shades. All mordants, increased the rub fastness and wash fastness of dyed samples, but the light fastness was increased except in case of alum. Berberine is a cationic dye and because of it's quaternary ammonium structure can act as an antibacterial agent. So, dyed samples were tested for antibacterial activity using AATCC test method 100-2004. The dyed wool represented a high level of antibacterial activity. The extract of the berberis vulgaris can be considered as a natural dye of acceptable fastness properties together with excellent antibacterial activity for woolen textiles.DOI: http://dx.doi.org/10.5755/j01.ms.18.3.2437

Surface Modifications of Polymers Induced by Heavy Ions Grafting

Energy Technology Data Exchange (ETDEWEB)

Mazzei, R O; Lombardo, J; Camporotondi, D; Tadey, D; Bermudez, G G [National Atomic Energy Commission, Ezeiza Atomic Centre, Ezeiza (Argentina)

2012-09-15

Polymer surfaces are modified by the application of swift heavy ions etching and grafting procedures. The residual active sites produced by heavy ion beams, remaining after the etching process, were used to start the grafting process. In order to produce tracks on foils of poly(vinylidene fluoride) (PVDF) they were irradiated with {sup 208}Pb of 25.62 MeV/n or with 115 MeV Cl ions. Moreover, foils of polypropylene (PP) were irradiated with {sup 208}Pb of 25.62 MeV/n. Then, they were etched and grafted with N-isopropylacrylamide (NIPAAm) monomers or with acrylic acid (AAc) monomers, respectively. The replica method allowed the observation of the shape of the grafted tracks using transmission electron microscopy (TEM). In addition NIPAAm grafted foils were analyzed using Fourier transform infrared spectroscopy (FTIR). The sulfonation procedure (methodology previously described for perfluorated polymers) was applied on grafted PVDF. A new method is described to produce a thin layer of poly-acrylic-acid (membranes) that grows on the surface of PVDF foils implanted by an Ar{sup +} beam with energies between 30-150 keV. Different combinations of monomers in water solutions were used such as: acrylic acid (AAc); acrylic acid-glycidyl methacrylate (AAc-GMA); acrylic acid-styrene (AAc-S); acrylic acid-N-isopropyl acrylamide (AAc-NIPAAm) and acrylic acid-N-isopropyl acrylamide - glycidyl methacrylate (AAc-NIPAAm-GMA). The experimental results show that for particular values of: ion fluence and energy, AAc concentration, sulphuric acid and PVDF polymorphous (alpha or beta) a huge percentage of grafting was obtained. At certain point of the grafting process the development of the PolyAAc-Xmonomer produce a detachment from the irradiated substrate and continue its grafting outside it. This method produces a membrane that is an increased replica of the original implanted surface. Finally, PVDF films implanted by an Ar{sup +} beam with energies about 100 keV and a fluence of 10

Styrene-Assisted Maleic Anhydride Grafted Poly(lactic acid as an Effective Compatibilizer for Wood Flour/Poly(lactic acid Bio-Composites

Directory of Open Access Journals (Sweden)

Jun Du

2017-11-01

Full Text Available This study aimed to evaluate the effect of styrene-assisted maleic anhydride-grafted poly(lactic acid (PLA-g-St/MAH on the interfacial properties of wood flour/poly(lactic acid (PLA bio-composites. PLA-g-St/MAH was synthesized by free-radical melt grafting using styrene as a comonomer and dicumyl peroxide as an initiator. The structure of PLA-g-St/MAH was characterized by Fourier transform infrared spectroscopy. Wood flour/PLA composites were prepared by compression molding using PLA-g-St/MAH as a compatibilizer. The effects of PLA-g-St/MAH on the rheological and mechanical properties, as well as on the fractured surface morphology of the composites were investigated. Results indicated that storage modulus, complex viscosity, equilibrium torque, and shear heat were significantly increased. The mechanical properties of the wood flour/PLA composites were also significantly increased after the addition of PLA-g-St/MAH. The maximum values were achieved at the loading rate of 3 wt % because of the improved interfacial adhesion between the wood flour and the PLA matrix.

Radiation-induced grafting of styrene on to LDPE films for preparation of cation exchange membranes, i. effect of grafting conditions

International Nuclear Information System (INIS)

Mohamed Mahmoud Nasef; Hamdani Saidi; Hussin Mohd Nor; Khairul Zaman Mohd Dahlan; Kamaruddin Hashim

1999-01-01

PE-g-polystyrene copolymers were prepared by simultaneous radiation-induced graft copolymerization of styrene onto low density polyethylene (LDPE) films. The effects of irradiation conditions such as monomer concentration, Mohr's salt and sulfuric acid addition, irradiation dose and dose rate were investigated. It was found that the degree of grafting increases with the monomer concentration and reaches its maximum value at styrene concentration of 80 vol %. The addition of Mohr's salt as well as sulfuric acid caused a considerable increase in the degree of grafting with various styrene concentrations. The degree of grafting also increased with the increased in irradiation dose, however it remarkably decreased with the increase in dose rate. The formation of graft copolymers was confirmed by FTIR analysis. The structural investigation of the graft copolymer was carried out by x-ray diffraction (XRD). The degree of crystallinity content was found to be decreased with the increase in the degree of grafting and influenced the mechanical properties of the graft copolymer to some extent. (Author)

China's Cotton Policy and the Impact of China's WTO Accession and Bt Cotton Adoption on the Chinese and U.S. Cotton Sectors

OpenAIRE

Cheng Fang; Bruce A. Babcock

2003-01-01

In this paper we provide an analysis of China's cotton policy and develop a framework to quantify the impact of both China's World Trade Organization (WTO) accession and Bt (Bacillus thuringiensis) cotton adoption on Chinese and U.S. cotton sectors. We use a Chinese cotton sector model consisting of supply, demand, price linkages, and textiles output equations. A two-stage framework model provides gross cropping area and total area for cotton and major subsitute crops from nine cotton-produci...

Rheological Behavior of Reaction Mixtures during the Graft Copolymerization of Cassava Starch with Acrylic Acid

NARCIS (Netherlands)

Witono, J.R.; Noordergraaf, Inge; Heeres, Hero; Janssen, L.P.B.M.

2017-01-01

Literature data on the rheological behavior of a reaction mixture during the graft copolymerization of acrylic acid onto gelatinized starch are scarce. Yet, such information is important for process design. In this work, continuous torque recording was found to be a suitable method to monitor the

Synthesis of perm-selective membranes by grafting acrylic acid into air-irradiated Teflon-FEP films

Science.gov (United States)

Bozzi, Annick; Chapiro, Adolphe

Grafting acrylic acid into air-irradiated Teflon-FEP films was investigated. Pre-irradiation doses ranged from 0.5 to 10 kGy. Grafting occurred at 45 or 60°C. Homopolymerization inhibitors, ferrous ions or methylene blue, were added to the system. It was found that after completion of the reaction, within 40-100 min, membranes were obtained with very low electric resistivities. The influence of added inhibitors, pre-irradiation dose and grafting temperature was studied. From the results it is concluded that the initiating centers in air-irradiated Teflon-FEP are, on the one hand, peroxides of structure POOP', in which P is a polymeric radical and Pprime; a small fragment, and on the other trapped PO .2 radicals. The latter only react after losing their oxygen. In the presence of polymerization inhibitors, initiation involves a redox process which reduces the overall activation energy.

Synthesis of perm-selective membranes by grafting acrylic acid into air-irradiated Teflon-FEP films

International Nuclear Information System (INIS)

Bozzi, Annick; Chapiro, Adolphe

1988-01-01

Grafting acrylic acid into air-irradiated Teflon-FEP films was investigated. Pre-irradiation doses ranged from 0.5 to 10 kGy. Grafting occurred at 45 or 60 0 C. Homopolymerization inhibitors, ferrous ions or methylene blue, were added to the system. It was found that after completion of the reaction, within 40-100 min, membranes were obtained with very low electric resistivities. The influence of added inhibitors, pre-irradiation dose and grafting temperature was studied. From the results it is concluded that the initiating centers in air-irradiated Teflon-FEP are, on the one hand, peroxides of structure POOP', in which P is a polymeric radical and P' a small fragment, and on the other hand trapped PO 2 sup(·) radicals. The latter only react after losing their oxygen. In the presence of polymerization inhibitors, initiation involves a redox process which reduces the overall activation energy. (author)

Potassium fulvate as co-interpenetrating agent during graft polymerization of acrylic acid from cellulose.

Science.gov (United States)

Ghazy, Mohamed B M; El-Hai, Farag Abd; Mohamed, Magdy F; Essawy, Hisham A

2016-10-01

Grafting polymerization of acrylic acid onto cellulose in presence of potassium fulvate (KF) as a co-interpenetrating agent results enhanced water sorption compared to materials prepared similarly in its absence. The insertion of potassium fulvate (KF) did not affect the grafting process and is thought to proceed in parallel to the graft polymerization via intensive polycondensation reactions of its function groups (-COOH and OH) with COOH of the monomer and OH groups of cellulose. The combination of graft copolymerization and polycondensation reactions is assumed to produce interpenetrating network structure. Fourier transform infrared (FTIR) confirmed successful incorporation within the network structure which is an evidence for formation of interpenetrating network. The obtained structures showed homogeneous uniform surface as revealed by scanning electron microscopy (SEM). The obtained superabsorbent possessed high water absorbency 422 and 48.8g/g in distilled water and saline (0.9wt.% NaCl solution), respectively, and enhanced water retention even at elevated temperatures as revealed by thermogravimetric analysis (TGA). This could be explained by the high content of hydrophilic groups. The new superabsorbents proved to be efficient devices for controlled release of fertilizers which expands their use in agricultural applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Combretastatin A4/poly(L-glutamic acid-graft-PEG conjugates self-assembled to nanoparticles

Directory of Open Access Journals (Sweden)

Yang Ou

2018-03-01

Full Text Available Combretastatin A4 (CA4 possesses varying ability to cause vascular disruption in tumors, while the short half-life, low water solubility and deactivation of many CA4 analogs during storage limited its antitumor efficacy and drug stability. A novel macromolecular conjugate of CA4 (CA4-PL was synthesized by covalent bonding of CA4 onto poly(L-glutamic acid-graft-polyethylene glycol (PLG-g-PEG via Yamaguchi reaction. The obtained CA4-PL was characterized by 1H NMR, GPC, and UV methods, and the properties of the nanoparticles composed of CA4-PL, including critical aggregation concentration, size and size distribution, and morphology, were investigated. CA4-PL can self-assemble to form micelle-like nanoparticles of 80~120 nm in diameter, which may have potential to improve the blood circulation period as well as the targetability of CA4, and find applications to treat various tumors when combined with traditional chemotherapy or radio therapy. Keywords: Combretastatin A4, Macromolecular conjugate, Poly(L-glutamic acid-graft-polyethylene glycol, Self-assemble, Nanoparticles

Graft polymerization using radiation-induced peroxides and application to textile dyeing

Energy Technology Data Exchange (ETDEWEB)

Enomoto, Ichiro, E-mail: enomoto.ichiro@iri-tokyo.j [Tokyo Metropolitan Industrial Technology Research Institute, KFC Bldg., 12F, 1-6-1, Yokoami, Sumida-ku, Tokyo 130-0015 (Japan); School of Engineering, University of Tokyo, 7-3-1, Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Katsumura, Yosuke [School of Engineering, University of Tokyo, 7-3-1, Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Advanced Science Research Center, Japan Atomic Energy Agency, 2-4 Shirakata Shirane, Tokai-mura, Ibaraki 319-1195 (Japan); Kudo, Hisaaki [School of Engineering, University of Tokyo, 7-3-1, Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Soeda, Shin [Tokyo Metropolitan Industrial Technology Research Institute, KFC Bldg., 12F, 1-6-1, Yokoami, Sumida-ku, Tokyo 130-0015 (Japan)

2011-02-15

To improve the dyeing affinity of ultra high molecular weight polyethylene (UHMWPE) fiber, surface treatment by radiation-induced graft polymerization was performed. Methyl methacrylate (MMA), acrylic acid (AA) and styrene (St) were used as the monomers. The grafting yields as a function of storage time after irradiation were examined. Although the grafting yield of St after the sulfonation processing was quite low compared with those of MMA and AA, it was successfully dyed to a dark color with a cationic dye. Some acid dyes can dye the grafted fiber with AA. The acid dye is distributed to the amorphous domains of the AA grafted fiber. The dyeing concentration depended on the grafting yield, and the higher the grafting yield the darker the dye color.

Graft polymerization using radiation-induced peroxides and application to textile dyeing

International Nuclear Information System (INIS)

Enomoto, Ichiro; Katsumura, Yosuke; Kudo, Hisaaki; Soeda, Shin

2011-01-01

To improve the dyeing affinity of ultra high molecular weight polyethylene (UHMWPE) fiber, surface treatment by radiation-induced graft polymerization was performed. Methyl methacrylate (MMA), acrylic acid (AA) and styrene (St) were used as the monomers. The grafting yields as a function of storage time after irradiation were examined. Although the grafting yield of St after the sulfonation processing was quite low compared with those of MMA and AA, it was successfully dyed to a dark color with a cationic dye. Some acid dyes can dye the grafted fiber with AA. The acid dye is distributed to the amorphous domains of the AA grafted fiber. The dyeing concentration depended on the grafting yield, and the higher the grafting yield the darker the dye color.

Impact of Bollgard cotton on Indian cotton production and Income of ...

Indian Academy of Sciences (India)

Impact of Bollgard cotton on Indian cotton production and Income of cotton farmers. Presentation made in the Seventy Second Annual Meeting Indian Academy of Sciences, Bangalore at Devi Ahilya Vishwavidyalaya Indore 11th November 2006.

THE ROLE OF QUALITY: SPANISH WOOL IN PORTUGUESE TRADE IN THE EARLY NINETEENTH CENTURY

Directory of Open Access Journals (Sweden)

Maria Cristina Moreira

2007-01-01

Full Text Available Cross-referencing qualitative and quantitative statistics from handwritten Portuguese trade sources shows the Spanish in the first half of the 19th century using Portuguese trade to introduce their wool in English and other markets. High quality Spanish merino wool played a key role in Portuguese trade during this period, particularly in the golden years of 1809-1819 and 1825. Its quality intensified both legal trade and smuggling.

Preparation and characterization of proton exchange poly (ether sulfone)s membranes grafted propane sulfonic acid on pendant phenyl groups

International Nuclear Information System (INIS)

Lim, Youngdon; Seo, Dongwan; Hossain, Md. Awlad; Lee, Soonho; Lim, Jinseong; Jang, Hohyoun; Hong, Taehoon; Kim,; Kim, Whangi

2014-01-01

Poly(ether sulfone)s containing hexaphenyl (PHP) was prepared by 1,2-bis(4-hydroxyphenyl)-3,4,5,6-tetraphenylbenzene, 4,4-hydroxyphenylsulfone, and 4,4-fluorophenylsulfone, followed bromination on phenyl groups to produce brominated PHP (Br-PHP). Grafted sulfonated poly(ether sulfone)s containing hexaphenyl (GSPHP) were prepared from Br-PHP and 3-bromopropane sulfonic acid with potassium salt and copper powder. The salt form was converted to free acid using 1 M sulfuric acid solution. All these membranes were cast from dimethylacetamide (DMAc). The structural properties of the synthesized polymers were investigated by 1 H-NMR spectroscopy. The membranes were studied with regard to ion exchange capacity (IEC), water uptake, Fenton test, and proton conductivity. These grafted polymer membranes were compared with normal sulfonated poly(ether sulfone)s and Nafion

Impact of efficient refuge policies for Bt cotton in India on world cotton trade

OpenAIRE

Singla, Rohit; Johnson, Phillip N.; Misra, Sukant K.

2010-01-01

India is a major cotton producing country in the world along with the U.S. and China. A change in the supply of and demand for cotton in the Indian market has the potential to have an impact on world cotton trade. This study evaluates the implications of efficient Bt cotton refuge policies in India on world and U.S. cotton markets. It can be hypothesized that increased refuge requirements for Bt cotton varieties in India could decrease the world supply of cotton because of the lower yield pot...

Study of inflammatory responses to crocidolite and basalt wool in the rat lung.

Science.gov (United States)

Adamis, Z; Kerényi, T; Honma, K; Jäckel, M; Tátrai, E; Ungváry, G

2001-03-09

The subacute effects of crocidolite and basalt wool dusts were studied by nmeans of biochemical, morphological. and histological methods 1 and .3 mo after intrabronchial instillation. The cell count, protein and phospholipid contents, and lactate dehydrogenase (LDH) activity were determined in the bronchoalveolar lavage (BAL). Both types of fibers induced a prolonged inflammatory reaction in the lung. All the parameters studied in the experimental groups were more markedly elevated after 3 mo. Relative to the control, the protein and LDH values were increased three- to fivefold, the phospholipid content twofold, and the number of free cells in the BAL exceeded the control level up to ninefold. The inflammatory responses to crocidolite and basalt wool in the lung did not differ significantly. In spite of this, basalt wool is recoinmended as an asbestos substitute, as the use of this man-nade fiber may result in a significantly lower release of dust than that from crocidolite.

A simple cost-effective and eco-friendly wet chemical process for the fabrication of superhydrophobic cotton fabrics

International Nuclear Information System (INIS)

Richard, Edna; Lakshmi, R.V.; Aruna, S.T.; Basu, Bharathibai J.

2013-01-01

Superhydrophobic surfaces were created on hydrophilic cotton fabrics by a simple wet chemical process. The fabric was immersed in a colloidal suspension of zinc hydroxide followed by subsequent hydrophobization with stearic acid. The wettability of the modified cotton fabric sample was studied by water contact angle (WCA) and water shedding angle (WSA) measurements. The modified cotton fabrics exhibited superhydrophobicity with a WCA of 151° for 8 μL water droplet and a WSA of 5–10° for 40 μL water droplet. The superhydrophobic cotton sample was also characterized by field emission scanning electron microscopy (FESEM) and energy dispersive X-ray spectroscopy (EDX). The method is simple, eco-friendly and cost-effective and can be applied to large area of cotton fabric materials. It was shown that superhydrophobicity of the fabric was due to the combined effect of surface roughness imparted by zinc hydroxide and the low surface energy of stearic acid.

A simple cost-effective and eco-friendly wet chemical process for the fabrication of superhydrophobic cotton fabrics

Energy Technology Data Exchange (ETDEWEB)

Richard, Edna; Lakshmi, R.V.; Aruna, S.T., E-mail: aruna_reddy@nal.res.in; Basu, Bharathibai J.

2013-07-15

Superhydrophobic surfaces were created on hydrophilic cotton fabrics by a simple wet chemical process. The fabric was immersed in a colloidal suspension of zinc hydroxide followed by subsequent hydrophobization with stearic acid. The wettability of the modified cotton fabric sample was studied by water contact angle (WCA) and water shedding angle (WSA) measurements. The modified cotton fabrics exhibited superhydrophobicity with a WCA of 151° for 8 μL water droplet and a WSA of 5–10° for 40 μL water droplet. The superhydrophobic cotton sample was also characterized by field emission scanning electron microscopy (FESEM) and energy dispersive X-ray spectroscopy (EDX). The method is simple, eco-friendly and cost-effective and can be applied to large area of cotton fabric materials. It was shown that superhydrophobicity of the fabric was due to the combined effect of surface roughness imparted by zinc hydroxide and the low surface energy of stearic acid.

Improving the livelihoods of wool producers in a sustainable manner ...

African Journals Online (AJOL)

Improving the livelihoods of wool producers in a sustainable manner by optimizing the woolled sheep production systems within the communal farming area of the Eastern Cape. “A vision that is future directed”

A grafting from approach to graft polystyrene chains at the surface of graphene nanolayers by RAFT polymerization: Various graft densities from hydroxyl groups

Energy Technology Data Exchange (ETDEWEB)

Roghani-Mamaqani, Hossein, E-mail: r.mamaghani@sut.ac.ir [Department of Polymer Engineering, Sahand University of Technology, PO Box 51335-1996, Tabriz (Iran, Islamic Republic of); Khezri, Khezrollah [School of Chemistry, University College of Science, University of Tehran, PO Box 14155-6455, Tehran (Iran, Islamic Republic of)

2016-01-01

Graphical abstract: (3-Aminopropyl) triethoxysilane was grafted at the surface of GO in low and high different graft densities to yield GOHAL and GOHAH, respectively. Subsequently, 2-(dodecylthiocarbonothioylthio)-2-methylpropionic acid (RA) was attached at the surface of GOHAL and GOHAH by an amidation reaction to yield GOHRL and GOHRH, respectively. Then, GOHRL and GOHRH were used in grafting from RAFT polymerization of styrene. - Highlights: • A RAFT agent grafted GO was used in grafting from RAFT polymerization of styrene. • The efficiency of RAFT agent attachment at the surface of GO is 41.12% for high density sample. • Polystyrene molecular weight is decreased by the addition of graphene content and also graft density of RAFT agent. - Abstract: (3-Aminopropyl) triethoxysilane was grafted at the surface of GO in low and high different graft densities to yield GOHAL and GOHAH, respectively. Subsequently, 2-(dodecylthiocarbonothioylthio)-2-methylpropionic acid (RA) was attached at the surface of GOHAL and GOHAH by an amidation reaction to yield GOHRL and GOHRH, respectively. Then, GOHRL and GOHRH were used in grafting from RAFT polymerization of styrene. Grafting of APTES and RA was approved by Fourier transform infrared spectroscopy, X-ray photo electron spectroscopy, and Raman spectroscopy. Expansion of graphene interlayer by oxidation and functionalization processes was evaluated by X-ray diffraction. Conversion values of styrene were calculated using gas chromatography. Molecular weight and PDI values of attached polystyrene (PS) chains were studied by size exclusion chromatography. Thermogravimetric analysis was also used to investigate the degradation temperatures, char contents, and graft contents of modifiers and PS chains. GOHRH and GOHRL reach to char content of 55.3 and 45.2% at 600 °C, which shows that weight ratio of modifier (APTES and RA moieties) is 15.3 and 5.2%, respectively. Scanning and transmission electron microscopies show that

Tensile and morphology properties of PLA/LNR blends modified with maleic anhydride grafted-polylactic acid and -natural rubber

Science.gov (United States)

Ruf, Mohd Farid Hakim Mohd; Ahmad, Sahrim; Chen, Ruey Shan; Shahdan, Dalila; Zailan, Farrah Diyana

2018-04-01

This research was carried out to investigate the addition of grafted copolymers of maleic anhydride grafted-polylactic acid(PLA-g-MA) and maleic anhydride grafted-natural rubber (NR-g-MA) on the tensile and morphology properties of polylactic acid/ liquid natural rubber (PLA/LNR) blends. Prior to blend preparation, the PLA-g-MA and NR-g-MA was first self-synthesized using maleic anhydride (MA) and dicumyl peroxide (DCP) as initiator together with the PLA and NR respectively. The PLA/LNR, PLA/LNR/PLA-g-MA and PLA/LNR/NR-g-MA blends were prepared via melt-blending method. The loading of PLA-g-MA and NR-g-MA was varied by 5, 10 and 15 wt% respectively. The addition of PLA-g-MA led to increment in tensile strength with 5 and 10 wt% while NR-g-MA gives lower than controlled sample (PLA/LNR blend). Scanning electron microscope (SEM) showed the interaction of the components in the blends. The PLA/LNR compatibilized with PLA-g-MA and NR-g-MA shows greater dispersion and adhesion.

Enhanced photocatalytic activity of wool-ball-like TiO2 microspheres on carbon fabric and FTO substrates

Science.gov (United States)

Zhang, Yu; Gu, Jian; Zhang, Mengqi

2018-06-01

The wool-ball-like TiO2 microspheres on carbon fabric (TiO2-CF) and FTO substrates (TiO2-FTO) have been synthesized by a facile hydrothermal method in alkali environment, using commercial TiO2 (P25) as precursors. The XRD results indicate that the as-prepared TiO2 have good crystallinity. And the SEM images show that the wool-ball-like TiO2 microspheres with a diameter of 2-3 μm are composed of TiO2 nanowires, which have a diameter of 50 nm. The photocatalytic behavior of the wool-ball-like TiO2 microspheres, TiO2-CF and TiO2-FTO under ultraviolet light was investigated by a pseudo first-order kinetic model, using methyl orange (MO) as pollutant. The wool-ball-like TiO2 microspheres obtained a degradation rate constant (Kap) of 6.91×10-3 min-1 . The Kap values of TiO2-FTO and TiO2-CF reach 13.97×10-3 min-1 and 11.80×10-3 min-1, which are 2.0 and 1.7 times higher than that of pristine wool-ball-like TiO2 microspheres due to the "sum effect" between TiO2 and substrates. This study offers a facile hydrothermal method to prepare wool-ball-like TiO2 microspheres on CF and FTO substrates, which will improve the recyclability of phtocatalysts and can be extended to other fields.

Bleaching of Wool with Sodium Borohydride

OpenAIRE

Duygu Yilmazer, MSc.; Mehmet Kanik, Ph.D.

2009-01-01

An untreated wool fabric was bleached both with sodium borohydride (SBH) in the presence of sodium bisulphite (SBS) solution and with a commercial H2O2 bleaching method. The concentration effects of SBH and SBS, bleaching time, pH and temperature on SBH bleaching process were investigated. Whiteness, yellowness and alkali solubility results were assessed for both bleaching methods. The results showed that whiteness degrees obtained with SBH bleaching was comparable with that of H2O2 bleaching...

Preparation and characterization of acrylic acid-grafted poly (vinyl alcohol) hydrogel actuators using γ-ray irradiation

International Nuclear Information System (INIS)

An, Sung Jun; Lim, Youn Mook; Gwon, Hui Jeong; Kim, Yun Hye; Youn, Min Ho; Nho, Young Chang; Han, Dong Hyun; Kim, Chong Yeal

2008-01-01

Active polymer gels expand and contract in response to certain environmental stimuli, such as the application of an electric field or a change in the pH level of the surroundings. This ability to achieve large, reversible deformations with no external mechanical loading has generated much interest in the use of these gels as biomimetic actuators and artificial muscles. In this study, poly (vinyl alcohol)(PVA) grafted acrylic acid monomer (PVA-g-AAc) hydrogels were prepared by 60 Co γ-ray irradiation and their properties such as degree of grafting and weight swelling in electrostimulation as an artificial muscle and actuator were investigated

Dictionary of Cotton

Science.gov (United States)

The Dictionary of Cotton has over 2,000 terms and definitions that were compiled by 33 researchers. It reflects the ongoing commitment of the International Cotton Advisory Committee, through its Technical Information Section, to the spread of knowledge about cotton to all those who have an interest ...

Performance of steel wool fiber reinforced geopolymer concrete

Science.gov (United States)

Faris, Meor Ahmad; Abdullah, Mohd Mustafa Al Bakri; Ismail, Khairul Nizar; Muniandy, Ratnasamy; Ariffin, Nurliayana

2017-09-01

In this paper, performance of geopolymer concrete was studied by mixing of Class F fly ash from Manjung power station, Lumut, Perak, Malaysia with alkaline activator which are combination of sodium hydroxide and sodium silicate. Steel wool fiber were added into the geopolymer concrete as reinforcement with different weight percentage vary from 0 % - 5 %. Chemical compositions of Malaysian fly ash was first analyzed by using X-ray fluorescence. All geopolymer concrete reinforced with steel wool fiber with different weight percentage were tested in terms of density, workability, and compression. Result shows Malaysian fly ash identified by using XRF was class F. Density of geopolymer concrete close to density of OPC which is approximately 2400 kg/m3 and the density was increase gradually with the additions of steel fiber. However, the inclusions of steel fibers also shows some reduction to the workability of geopolymer concrete. Besides, the compressive strength was increased with the increasing of fibers addition until maximum of 18.6 % improvement at 3 % of steel fibers.

Chemical hydrogels based on a hyaluronic acid-graft-α-elastin derivative as potential scaffolds for tissue engineering

International Nuclear Information System (INIS)

Palumbo, Fabio Salvatore; Pitarresi, Giovanna; Fiorica, Calogero; Rigogliuso, Salvatrice; Ghersi, Giulio; Giammona, Gaetano

2013-01-01

In this work hyaluronic acid (HA) functionalized with ethylenediamine (EDA) has been employed to graft α-elastin. In particular a HA-EDA derivative bearing 50 mol% of pendant amino groups has been successfully employed to produce the copolymer HA-EDA-g-α-elastin containing 32% w/w of protein. After grafting with α-elastin, remaining free amino groups reacted with ethylene glycol diglycidyl ether (EGDGE) for producing chemical hydrogels, proposed as scaffolds for tissue engineering. Swelling degree, resistance to chemical and enzymatic hydrolysis, as well as preliminary biological properties of HA-EDA-g-α-elastin/EGDGE scaffold have been evaluated and compared with a HA-EDA/EGDGE scaffold. The presence of α-elastin grafted to HA-EDA improves attachment, viability and proliferation of primary rat dermal fibroblasts and human umbilical artery smooth muscle cells. Biological performance of HA-EDA-g-α-elastin/EGDGE scaffold resulted comparable to that of a commercial collagen type I sponge (Antema®), chosen as a positive control. - Highlights: ► Hyaluronic acid (HA) has been functionalized with ethylenediamine (EDA). ► Amino groups of HA-EDA allow the reaction with α-elastin and ethylene glycol diglycidyl ether (EGDGE). ► Chemical scaffolds of HA-EDA-graft-α-elastin/EGDGE have been characterized. ► The presence of α-elastin affects porosity, swelling and enzymatic degradation of scaffolds. ► The presence of α-elastin improves attachment, viability and proliferation of fibroblasts and smooth muscle cells

Chemical hydrogels based on a hyaluronic acid-graft-α-elastin derivative as potential scaffolds for tissue engineering

Energy Technology Data Exchange (ETDEWEB)

Palumbo, Fabio Salvatore [Dipartimento di Scienze e Tecnologie Molecolari e Biomolecolari, Sezione di Chimica e Tecnologie Farmaceutiche, Università degli Studi di Palermo, Via Archirafi 32, 90123, Palermo (Italy); Pitarresi, Giovanna, E-mail: giovanna.pitarresi@unipa.it [Dipartimento di Scienze e Tecnologie Molecolari e Biomolecolari, Sezione di Chimica e Tecnologie Farmaceutiche, Università degli Studi di Palermo, Via Archirafi 32, 90123, Palermo (Italy); Institute of Biophysics at Palermo, Italian National Research Council, Via Ugo La Malfa 153, 90146 Palermo (Italy); Fiorica, Calogero [Dipartimento di Scienze e Tecnologie Molecolari e Biomolecolari, Sezione di Chimica e Tecnologie Farmaceutiche, Università degli Studi di Palermo, Via Archirafi 32, 90123, Palermo (Italy); Rigogliuso, Salvatrice; Ghersi, Giulio [Dipartimento di Scienze e Tecnologie Molecolari e Biomolecolari, Sezione di Biologia Cellulare, Università degli Studi di Palermo, Viale delle Scienze ed. 16, 90128, Palermo (Italy); Giammona, Gaetano [Dipartimento di Scienze e Tecnologie Molecolari e Biomolecolari, Sezione di Chimica e Tecnologie Farmaceutiche, Università degli Studi di Palermo, Via Archirafi 32, 90123, Palermo (Italy); IBIM-CNR, Via Ugo La Malfa 153, 90146 Palermo (Italy)

2013-07-01

In this work hyaluronic acid (HA) functionalized with ethylenediamine (EDA) has been employed to graft α-elastin. In particular a HA-EDA derivative bearing 50 mol% of pendant amino groups has been successfully employed to produce the copolymer HA-EDA-g-α-elastin containing 32% w/w of protein. After grafting with α-elastin, remaining free amino groups reacted with ethylene glycol diglycidyl ether (EGDGE) for producing chemical hydrogels, proposed as scaffolds for tissue engineering. Swelling degree, resistance to chemical and enzymatic hydrolysis, as well as preliminary biological properties of HA-EDA-g-α-elastin/EGDGE scaffold have been evaluated and compared with a HA-EDA/EGDGE scaffold. The presence of α-elastin grafted to HA-EDA improves attachment, viability and proliferation of primary rat dermal fibroblasts and human umbilical artery smooth muscle cells. Biological performance of HA-EDA-g-α-elastin/EGDGE scaffold resulted comparable to that of a commercial collagen type I sponge (Antema®), chosen as a positive control. - Highlights: ► Hyaluronic acid (HA) has been functionalized with ethylenediamine (EDA). ► Amino groups of HA-EDA allow the reaction with α-elastin and ethylene glycol diglycidyl ether (EGDGE). ► Chemical scaffolds of HA-EDA-graft-α-elastin/EGDGE have been characterized. ► The presence of α-elastin affects porosity, swelling and enzymatic degradation of scaffolds. ► The presence of α-elastin improves attachment, viability and proliferation of fibroblasts and smooth muscle cells.

Blend membrane of succinic acid-crosslinked chitosan grafted with heparin/PVA-PEG (polyvinyl alcohol-polyethylene glycol) and its characterization

Science.gov (United States)

Sangkota, V. D. A.; Lusiana, R. A.; Astuti, Y.

2018-04-01

Crosslinking and grafting reactions are required to modify the functional groups on chitosan to increase the number of its active groups. In this study, crosslinking reaction of succinic acid and grafting reaction of heparin on chitosan were conducted to produce a membrane as a candidate of a hemodialysis membrane. The mole ratio between chitosan and succinate acids was varied to obtain the best composition of modified materials. By blending all the material composition with PVA-PEG, the blend was transformed into a membrane. The resulted membrane was then characterized by various test methods such as tests of thickness, weight, water uptake, pH resistance, tensile strength and membrane hydrophilicity. The results showed that the best composition of the membrane reached in the addition of 0.011 gram of succinic acid proved by its highest mechanical strength compared to the other membranes.

Measurements of anisotropic sound propagation in glass wool

DEFF Research Database (Denmark)

Tarnow, Viggo

2000-01-01

to the glass wool sheets was 75 dB/m, and for propagation parallel with the sheets 57 dB/m. For mass density 30 kg/m3, the corresponding numbers were 140 and 100 dB/m. The measured values were compared with calculated ones taking into account the movements of the fiber skeleton. The calculations need...

Synthesis of Novel UV Absorbers Bisindolylmethanes and Investigation of Their Applications on Cotton-Based Textile Materials

Directory of Open Access Journals (Sweden)

Hikmet Nil Ergindemir

2016-06-01

Full Text Available Nowadays modified textiles, especially UV-protective, antibacterial and antimicrobial ones, have become the focus of great interest. In this study, several new UV absorbers, bis(indolylmethane derivatives, were synthesized and grafted onto polyvinyl alcohol polymer (PVA. Their application properties on cotton-based textile materials were determined; the UV protection factor values of the modified fabrics were measured (UPF; and the antibacterial features of the fabrics were tested.

Biocompatibility of polypropylene non-woven fabric membrane via UV-induced graft polymerization of 2-acrylamido-2-methylpropane sulfonic acid

Energy Technology Data Exchange (ETDEWEB)

Song Lingjie [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Zhao Jie; Yang Huawei; Jin Jing; Li Xiaomeng [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Stagnaro, Paola [Istituto per Io Studio delle Macromolecole, Consiglio Nazionale delle Ricerche, Via de Marini 6, 16149 Genova (Italy); Yin Jinghua, E-mail: yinjh@ciac.jl.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

2011-10-15

This work described the graft polymerization of a sulfonic acid terminated monomer, 2-acrylamido-2-methylpropane sulfonic acid (AMPS), onto the surface of polypropylene non-woven (NWF PP) membrane by O{sub 2} plasma pretreatment and UV-induced photografting method. The chemical structure and composition of the modified surfaces were analyzed by FTIR-ATR and XPS, respectively. The wettability was investigated by water contact angle and equilibrium water adsorption. And the biocompatibility of the modified NWF PP membranes was evaluated by protein adsorption and platelet adhesion. It was found that the graft density increased with prolonging UV irradiation time and increasing AMPS concentration; the water contact angles of the membranes decreased from 124{sup o} to 26{sup o} with the increasing grafting density of poly(AMPS) from 0 to 884.2 {mu}g cm{sup -2}, while the equilibrium water adsorption raised from 5 wt% to 75 wt%; the protein absorption was effectively suppressed with the introduction of poly(AMPS) even at the low grafting density (132.4 {mu}g cm{sup -2}); the number of platelets adhering to the modified membrane was dramatically reduced when compared with that on its virgin surface. These results indicated that surface modification of NWF PP membrane with AMPS was a facile approach to construct biocompatible surface.

Pre-irradiation grafting of hydrophilic monomers onto polyethylene: Pt. 1

International Nuclear Information System (INIS)

Gargan, K.; Kronfli, E.; Lovell, K.V.

1990-01-01

An investigation was carried out to identify compounds which are suitable for use as homopolymerisation inhibitors when grafting acrylic acid or methacrylic acid onto pre-irradiated low-density polyethylene. It was found that certain transition metal compounds were able to suppress the formation of homopolymer whilst still allowing significant levels of grafting to take place. For acrylic acid the most suitable inhibitor found was ferrous sulphate, whilst cupric sulphate or potassium ferrocyanide were favoured for use with methacrylic acid. The influence of the inhibitor concentration on the degree of grafting was also investigated. (author)

Fast microwave-assisted green synthesis of xanthan gum grafted acrylic acid for enhanced methylene blue dye removal from aqueous solution.

Science.gov (United States)

Makhado, Edwin; Pandey, Sadanand; Nomngongo, Philiswa N; Ramontja, James

2017-11-15

In the present project, graft polymerization was employed to synthesis a novel adsorbent using acrylic acid (AA) and xanthan gum (XG) for cationic methylene dye (MB + ) removal from aqueous solution. The XG was rapidly grafted with acrylic acid (CH 2 =CHCOOH) under microwave heating. Fourier-transform infrared spectroscopy (FTIR), Proton Nuclear magnetic resonance spectroscopy ( 1 H NMR), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Thermal gravimetric analysis (TGA) techniques were used to verify the adsorbent formed under optimized reaction conditions. Optimum reaction conditions [AA (0.4M), APS (0.05M), XG (2gL -1 ), MW power (100%), MW time (80s)] offer maximum %G and %GE of 484 and 78.3, respectively. The removal ratio of adsorbent to MB + reached to 92.8% at 100mgL -1 . Equilibrium and kinetic adsorptions of dyes were better explained by the Langmuir isotherm and pseudo second-order kinetic model respectively. The results demonstrate xanthan gum grafted polyacrylic acid (mw XG-g-PAA) absorbent had the universality for removal of dyes through the chemical adsorption mechanism. Copyright © 2017 Elsevier Ltd. All rights reserved.

COLORING PROPERTIES OF WOOL FABRIC COLORED BY NEW DYESTUFFS - AZOMETHINES

Directory of Open Access Journals (Sweden)

DJORDJEVIC Dragan

2016-05-01

Full Text Available The azomethines have broad applications in food and dyestuff industries, and in analytical chemistry, catalysis and also in the field of agrochemical. These have played an influential part in the improvement of modern coordination chemistry, but also they can also be found at key points in the development of inorganic biochemistry, catalysis and also in optical materials. The present paper describes coloring properties of wool fabric colored by new dyestuffs - azomethines, derivate of isatin. Synthesizing of dyestuffs can often have one to six chromogen, which can be defined as the photoactive components that contain colored or uncolored absorbent components. In addition of monoazo, diazo, poly-azo, anthraquinone, xanthan and similar systems, the azomethines or imines, also includes to the chromogen groups. Azomethines, such as, isatin-3-hydrazone, isatin-3-thiosemicarbazone and isatin-3-phenylhydrazone, were synthesized and their coloring performance on wool fabric assessed. The synthesized azomethines showed very good substantively for wool fibers with good coloring performance according to CIEL*a*b* system which characterized quantitative and qualitative coloring property. Dyestuff 3 or isatin-3-phenylhydrazone bound to woolen textiles to a greater extent and greater intensity (minimum value of L. Dyestuff 2 or isatin-3-thiosemicarbazone linked to the minimum amount for textiles (the largest value of L. Although it must be noted that it is a lighter shade (yellow color as opposed to the dyestuff 3 (red color.

Extracting natural dyes from wool--an evaluation of extraction methods.

Science.gov (United States)

Manhita, Ana; Ferreira, Teresa; Candeias, António; Dias, Cristina Barrocas

2011-05-01

The efficiency of eight different procedures used for the extraction of natural dyes was evaluated using contemporary wool samples dyed with cochineal, madder, woad, weld, brazilwood and logwood. Comparison was made based on the LC-DAD peak areas of the natural dye's main components which had been extracted from the wool samples. Among the tested methods, an extraction procedure with Na(2)EDTA in water/DMF (1:1, v/v) proved to be the most suitable for the extraction of the studied dyes, which presented a wide range of chemical structures. The identification of the natural dyes used in the making of an eighteenth century Arraiolos carpet was possible using the Na(2)EDTA/DMF extraction of the wool embroidery samples and an LC-DAD-MS methodology. The effectiveness of the Na(2)EDTA/DMF extraction method was particularly observed in the extraction of weld dye components. Nine flavone derivatives previously identified in weld extracts could be identified in a single historical sample, confirming the use of this natural dye in the making of Arraiolos carpets. Indigo and brazilwood were also identified in the samples, and despite the fact that these natural dyes were referred in the historical recipes of Arraiolos dyeing, it is the first time that the use of brazilwood is confirmed. Mordant analysis by ICP-MS identified the widespread use of alum in the dyeing process, but in some samples with darker hues, high amounts of iron were found instead.

Potassium fulvate-modified graft copolymer of acrylic acid onto cellulose as efficient chelating polymeric sorbent.

Science.gov (United States)

Mohamed, Magdy F; Essawy, Hisham A; Ammar, Nabila S; Ibrahim, Hanan S

2017-01-01

Acrylic acid (AA) was graft copolymerized from cellulose (Cell) in presence of potassium fulvate (KF) in order to enhance the chemical activity of the resulting chelating polymer and the handling as well. Fourier transform infrared (FTIR) proved that KF was efficiently inserted and became a permanent part of the network structure of the sorbent in parallel during the grafting copolymerization. Scanning electron microscopy (SEM) revealed intact homogeneous structure with uniform surface. This indicates improvement of the handling, however, it was not the case for the graft copolymer of acrylic acid onto cellulose in absence of KF, which is known to be brittle and lacks mechanical integrity. Effective insertion of this co-interpenetrating agent provided more functional groups, such as OH and COOH, which improved the chelating power of the produced sorbent as found for the removal of Cu 2+ ions from its aqueous solutions (the removal efficiency reached ∼98.9%). Different models were used to express the experimental data. The results corroborated conformity of the pseudo-second order kinetic model and Langmuir isotherm model to the sorption process, which translates into dominance of the chemisorption. Regeneration of the chelating polymers under harsh conditions did not affect the efficiency of copper ions uptake up to three successive cycles. A thermodynamic investigation ensured exothermic nature of the adsorption process that became less favourable at higher temperatures. Copyright © 2016 Elsevier B.V. All rights reserved.

Seed prepare for oil content determination by NMR method in six cotton varieties

International Nuclear Information System (INIS)

Gondim-Tomaz, Rose Marry Araujo; Erismann, Norma de Magalhaes; Sabino, Nelson Paulieri; Kondo, Julio Isao; Cia, Edivaldo; Azzini, Anisio; Soave, Daise

1998-01-01

Three comparative methods (chemical seed-delinting with sulphuric acid solution, flaming and seed with linter) to prepare cotton seeds for oil determination by the Nuclear Magnetic Resonance (NMR) technique were considered. The chemical treatment with sulphuric acid was the best as long the linter interference was eliminated. The seed oil contents were determined by the NMR method in six cotton varieties from the national variety test. The IAPAR (Instituto Agronomico do Parana) 71 PR3 and IAC (Instituto Agronomico de Campinas) 20 varieties presented the highest oil content followed by the CNPA 7H, CS 50, IAC 22 and CNPA Precoce 2. (author)

Novel multi-biotin grafted poly(lactic acid) and its self-assembling nanoparticles capable of binding to streptavidin

Science.gov (United States)

Yan, Hao; Jiang, Weimin; Zhang, Yinxing; Liu, Ying; Wang, Bin; Yang, Li; Deng, Lihong; Singh, Gurinder K; Pan, Jun

2012-01-01

Targeted drug delivery requires novel biodegradable, specific binding systems with longer circulation time. The aim of this study was to prepare biotinylated poly(lactic acid) (PLA) nanoparticles (NPs) which can meet regular requirements as well conjugate more biotins in the polymer to provide better binding with streptavidin. A biotin-graft-PLA was synthesized based on previously published biodegradable poly(ethylene glycol) (PEG)-graft-PLA, with one polymer molecule containing three PEG molecules. Newly synthesized biotin-graft-PLA had three biotins per polymer molecule, higher than the previous biotinylated PLA (≤1 biotin per polymer molecule). A PEG with a much lower molecular weight (MW ~1900) than the previous biotinylated PLA (PEG MW ≥ 3800), and thus more biocompatible, was used which supplied good nonspecific protein-resistant property compatible to PEG-graft-PLA, suggesting its possible longer stay in the bloodstream. Biotin-graft-PLA specifically bound to streptavidin and self-assembled into NPs, during which naproxen, a model small molecule (MW 230 Da) and hydrophobic drug, was encapsulated (encapsulation efficiency 51.88%). The naproxen-loaded NPs with particle size and zeta potential of 175 nm and −27.35 mV realized controlled release within 170 hours, comparable to previous studies. The biotin-graft-PLA NPs adhered approximately two-fold more on streptavidin film and on biotin film via a streptavidin arm both in static and dynamic conditions compared with PEG-graft-PLA NPs, the proven nonspecific protein-resistant NPs. The specific binding of biotin-graft-PLA NPs with streptavidin and with biotin using streptavidin arm, as well as its entrapment and controlled release for naproxen, suggest potential applications in targeted drug delivery. PMID:22334778

Graft copolymers of polypropylene films. 1. radiation induced grafting of mixed monomers. Vol. 3

International Nuclear Information System (INIS)

El-Salmawi, K.M.; El-Naggar, A.M.; Said, H.M.; Zahran, A.H.

1996-01-01

Radiation graft copolymerization of co monomer mixtures of acrylic acid (AAC), and styrene (S) onto polypropylene (PP) film by mutual method has been investigated. The effects of different factors that may affect the grafting yield such as inhibitor concentration (Mohr's salt), solvent composition (MeOH and H 2 O), radiation dose and dose rate were considered. It was found that the role of Mohr's salt is very effective when the ratio of AAC in the co monomer mixtures was at lower values. However, the addition of 1.25 Wt% of Mohr's salt reduced the homo polymer formation and enhances the grafting process. Graft copolymerization in presence of solvent mixture composed of methanol and water was found to afford higher grafting than in pure methanol regardless of the composition of the co monomer mixture used. However, the highest degree of grafting was obtained at a solvent composition of 20% H 2 O:80%MeOH and a co monomer mixture of 20%AAC:80%sty. An attempt was made to determine each PAAC and PS fractions in the total graft yield obtained. Two methods of analysis based on using the reactivity ratios reported in literature, elemental analysis and IR spectroscopy. The determination of poly (acrylic acid) and polystyrene fractions by elemental analysis is believed more accurate than these by reactivity ratio. The precise results obtained by elemental analysis with respect to the chemical structure of known polymer prepared under identical conditions. The results obtained by IR measurements go well with that obtained with the reactivity ratio methods. 5 figs., 3 tabs

Characterization of the material produced using marble waste and reagents aiminig production of rock wool

International Nuclear Information System (INIS)

Rodrigues, Girley Ferreira; Espinosa, Denise Crocce Romano; Tenorio, Jorge Alberto Soares; Alves, Joner Oliveira

2010-01-01

The aim of this work was to characterize materials produced from the mixture of marble waste and chemical reagents. The materials were homogenized, melted and cooled in order to obtain materials with similar characteristics of rock wools. The batch was poured in a water-filled recipient and also in a Herty viscometer at three temperatures. Samples of produced materials were characterized by X-ray diffraction, scanning electron microscopy and differential thermal analysis. Results of this study indicate that it is possible the incorporation of marble waste in the production process of rock wool, replacing approximately 15% of the raw material used to fabricate this material. This process represents a technological breakthrough since it allows the reuse of marble waste, and also represents a possible decrease in rock wool production cost, which is a material with a growing market as thermo acoustic insulator. (author)

Functionalization of LDPE and mLLDPE via grafting trans-ethylene-1,2-dicarboxylic acid by reactive extrusion

Directory of Open Access Journals (Sweden)

2010-03-01

Full Text Available An investigation was made of grafting trans-ethylene-1,2-dicarboxylic acid (TEDA onto metallocene-linear low-density polyethylene (mLLDPE and low-density polyethylene (LDPE in the course of reactive extrusion. The initiator was 1,3-bis-(tert-butyl-peroxyisopropylbenzene. The graft efficiency of TEDA has been shown to increase with increasing initiator concentration, irrespective of polyethylene type. The graft values for LDPE were higher than for mLLDPE over the initiator concentration range (0.05 to 0.4 wt%. The rheological properties of mLLDPE were found to undergo more tangible changes during functionalization than those of LDPE. These changes were caused by side reactions, mainly macromolecular crosslinking. It has been established that some carboxyl groups get transformed to anhydride groups in the grafted product. The concentration of end double bonds reduces, but intramolecular unsaturation in both polyethylenes increases. Data are presented on thermal and stress-strain (mechanical properties of virgin and functionalized polymers, as well as rheological and viscoelastic properties of their melts.

Synthesis and electrochemical probing of water-soluble poly(sodium 4-styrenesulfonate-co-acrylic acid)-grafted multiwalled carbon nanotubes

International Nuclear Information System (INIS)

Du Feipeng; Yang Yingkui; Xie Xiaolin; Wu Kangbing; Gan Tian; Liu Lang

2008-01-01

Water-soluble poly(sodium 4-styrenesulfonate-co-acrylic acid)-grafted multiwalled carbon nanotubes (MWNT-g-P(SSS-co-AA)) with core-shell nanostructure were successfully synthesized by in situ free radical copolymerization of sodium 4-strenesulfonate (SSS) and acrylic acid (AA) in the presence of MWNTs terminated with vinyl groups; their structure was characterized by FTIR, 1 H NMR, Raman, TGA and TEM. The results showed that the thickness and content of the copolymer layer grafted onto the MWNT surface are about 7-12 nm and 82.3%, respectively. The P(SSS-co-AA) covalently grafted on MWNTs provides MWNT-g-P(SSS-co-AA) with good hydrophilicity and solubility in water. Then a novel MWNT-g-P(SSS-co-AA)-modified glassy carbon electrode was fabricated by coating; its electrochemical properties were evaluated by electrochemical probe of K 3 [Fe(CN) 6 ], and its catalytic behaviors to the electrochemical oxidation processes of dopamine (DA) and serotonin (5-HT) were investigated. Since the MWNT-g-P(SSS-co-AA)-modified electrode possesses strong electron transfer capability, high electrochemical activity and catalytic ability, it can be used in sensitive, selective, rapid and simultaneous monitoring of biomolecules

A comparative study on the graft copolymerization of acrylic acid onto rayon fibre by a ceric ion redox system and a γ-radiation method.

Science.gov (United States)

Kaur, Inderjeet; Kumar, Raj; Sharma, Neelam

2010-10-13

Functionalization of rayon fibre has been carried out by grafting acrylic acid (AAC) both by a chemical method using a Ce(4+)-HNO(3) redox initiator and by a mutual irradiation (γ-rays) method. The reaction conditions affecting the grafting percentage have been optimized for both methods, and the results are compared. The maximum percentage of grafting (50%) by the chemical method was obtained utilizing 18.24 × 10(-3) moles/L of ceric ammonium nitrate (CAN), 39.68 × 10(-2) moles/L of HNO(3), and 104.08 × 10(-2) moles/L of AAc in 20 mL of water at 45°C for 120 min. For the radiation method, the maximum grafting percentage (60%) was higher, and the product was obtained under milder reaction conditions using a lower concentration of AAc (69.38 × 10(-2) moles/L) in 10 mL of water at an optimum total dose of 0.932 kGy. Swelling studies showed higher swelling for the grafted rayon fibre in water (854.54%) as compared to the pristine fibre (407%), while dye uptake studies revealed poor uptake of the dye (crystal violet) by the grafted fibre in comparison with the pristine fibre. The graft copolymers were characterized by IR, TGA, and scanning electron micrographic methods. Grafted fibre, prepared by the radiation-induced method, showed better thermal behaviour. Comparison of the two methods revealed that the radiation method of grafting of acrylic acid onto rayon fibre is a better method of grafting in comparison with the chemical method. Copyright © 2010 Elsevier Ltd. All rights reserved.

Cost-Benefit and Performance of Handmade Carpets Produced with Wool, Untreated and Chemical Treated Jute Pile Yarns

Science.gov (United States)

Gupta, Shravan Kumar; Goswami, Kamal Kanti

2018-03-01

Jute is a natural fibre which is used to make different type of products due to low cost, easy availability and eco-friendliness. However, the stiffness and harshness of jute fibre affect the use of jute in many products like pile yarns in hand knotted carpets. In this research, a study has been done on the application of jute pile yarns in Persian hand knotted carpet. Three types of commercial yarns (wool, untreated jute and woollenized jute) as well as three types of chemical treated jute yarns (hydrogen peroxide bleached, softened bleached and woollenized yarns) have been applied as pile yarns in Persian hand knotted carpets. Cost-benefit analysis of hand knotted carpets shows that manufacturing cost of wool carpet is lower than others. The contribution of manpower charges is higher than material cost during carpet manufacturing. Hand knotted carpet shows the lowest pile abrasion loss and highest compression recovery when wool is used as pile. Wool hand knotted carpet shows higher compression than untreated and treated jute carpets.

Fundus Findings in Dengue Fever: A Case Report

Directory of Open Access Journals (Sweden)

Berna Şahan

2015-10-01

Full Text Available Dengue fever is a flavivirus infection transmitted through infected mosquitoes, and is endemic in Southeast Asia, Central and South America, the Pacific, Africa and the Eastern Mediterranean region. A 41-year-old male patient had visual impairment after travelling to Thailand, which is one of the endemic areas. Cotton wool spots were observed on fundus examination. Fundus fluorescein angiography showed minimal vascular leakage from areas near the cotton wool spots and dot hemorrhages in the macula. Dengue fever should be considered in patients with visual complaints who traveled to endemic areas of dengue fever. (Turk J Ophthalmol 2015; 45: 223-225

Fabrication and Characterization of Electrospun Wool Keratin/Poly(vinyl alcohol Blend Nanofibers

Directory of Open Access Journals (Sweden)

Shuai Li

2014-01-01

Full Text Available Wool keratin/poly(vinyl alcohol (PVA blend nanofibers were fabricated using the electrospinning method in formic acid solutions with different weight ratios of keratin to PVA. The resultant blend nanofibers were characterized by scanning electron microscopy (SEM, Fourier transform infrared (FTIR, X-ray diffraction (XRD, thermal gravimetric analysis (TGA, and tensile test. SEM images showed that the diameter of the blend nanofibers was affected by the content of keratin in blend solution. FTIR and XRD analyses data demonstrated that there were good interactions between keratin and PVA in the blended nanofibers caused by possibly hydrogen bonds. The TGA study revealed that the thermal stability of the blend nanofibers was between those of keratin and PVA. Tensile test indicated that the addition of PVA was able to improve the mechanical properties of the electrospun nanofibers.

[Correlation analysis between single nucleotide polymorphism of FGF5 gene and wool yield in rabbits].

Science.gov (United States)

Li, Chun-Xiao; Jiang, Mei-Shan; Chen, Shi-Yi; Lai, Song-Jia

2008-07-01

Single nucleotide polymorphism (SNP) in exon 1 and 3 of fibroblast growth factor (FGF5) gene was studied by DNA sequencing in Yingjing angora rabbit, Tianfu black rabbit and California rabbit. A frameshift mutation (TCT insert) at base position 217 (site A) of exon 1 and a T/C missense mutation at base position 59 (site B) of exon 3 were found in Yingjing angora rabbit with a high frequency; a T/C same-sense mutation at base position 3 (site C) of exon 3 was found with similar frequency in three rabbit breeds. Least square analysis showed that different genotypes had no significant association with wool yield in site A, and had high significant association with wool yield in site B (Plink with the major gene, and polymorphic loci B and C may be used as molecular markers for im-proving wool yield in angora rabbits.

Comparative Study of Ultrasonication-Induced and Naturally Self-Assembled Silk Fibroin-Wool Keratin Hydrogel Biomaterials.

Science.gov (United States)

Vu, Trang; Xue, Ye; Vuong, Trinh; Erbe, Matthew; Bennet, Christopher; Palazzo, Ben; Popielski, Lucas; Rodriguez, Nelson; Hu, Xiao

2016-09-07

This study reports the formation of biocompatible hydrogels using protein polymers from natural silk cocoon fibroins and sheep wool keratins. Silk fibroin protein contains β-sheet secondary structures, allowing for the formation of physical cross-linkers in the hydrogels. Comparative studies were performed on two groups of samples. In the first group, ultrasonication was used to induce a quick gelation of a protein aqueous solution, enhancing the ability of Bombyx mori silk fibroin chains to quickly entrap the wool keratin protein molecules homogenously. In the second group, silk/keratin mixtures were left at room temperature for days, resulting in naturally-assembled gelled solutions. It was found that silk/wool blended solutions can form hydrogels at different mixing ratios, with perfectly interconnected gel structure when the wool content was less than 30 weight percent (wt %) for the first group (ultrasonication), and 10 wt % for the second group (natural gel). Differential scanning calorimetry (DSC) and temperature modulated DSC (TMDSC) were used to confirm that the fibroin/keratin hydrogel system was well-blended without phase separation. Fourier transform infrared spectroscopy (FTIR) was used to investigate the secondary structures of blended protein gels. It was found that intermolecular β-sheet contents significantly increase as the system contains more silk for both groups of samples, resulting in stable crystalline cross-linkers in the blended hydrogel structures. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to analyze the samples' characteristic morphology on both micro- and nanoscales, which showed that ultrasonic waves can significantly enhance the cross-linker formation and avoid phase separation between silk and keratin molecules in the blended systems. With the ability to form cross-linkages non-chemically, these silk/wool hydrogels may be economically useful for various biomedical applications, thanks to the

Comparative Study of Ultrasonication-Induced and Naturally Self-Assembled Silk Fibroin-Wool Keratin Hydrogel Biomaterials

Directory of Open Access Journals (Sweden)

Trang Vu

2016-09-01

Full Text Available This study reports the formation of biocompatible hydrogels using protein polymers from natural silk cocoon fibroins and sheep wool keratins. Silk fibroin protein contains β-sheet secondary structures, allowing for the formation of physical cross-linkers in the hydrogels. Comparative studies were performed on two groups of samples. In the first group, ultrasonication was used to induce a quick gelation of a protein aqueous solution, enhancing the ability of Bombyx mori silk fibroin chains to quickly entrap the wool keratin protein molecules homogenously. In the second group, silk/keratin mixtures were left at room temperature for days, resulting in naturally-assembled gelled solutions. It was found that silk/wool blended solutions can form hydrogels at different mixing ratios, with perfectly interconnected gel structure when the wool content was less than 30 weight percent (wt % for the first group (ultrasonication, and 10 wt % for the second group (natural gel. Differential scanning calorimetry (DSC and temperature modulated DSC (TMDSC were used to confirm that the fibroin/keratin hydrogel system was well-blended without phase separation. Fourier transform infrared spectroscopy (FTIR was used to investigate the secondary structures of blended protein gels. It was found that intermolecular β-sheet contents significantly increase as the system contains more silk for both groups of samples, resulting in stable crystalline cross-linkers in the blended hydrogel structures. Scanning electron microscopy (SEM and atomic force microscopy (AFM were used to analyze the samples’ characteristic morphology on both micro- and nanoscales, which showed that ultrasonic waves can significantly enhance the cross-linker formation and avoid phase separation between silk and keratin molecules in the blended systems. With the ability to form cross-linkages non-chemically, these silk/wool hydrogels may be economically useful for various biomedical applications

Treating landfill gas hydrogen sulphide with mineral wool waste (MWW) and rod mill waste (RMW).

Science.gov (United States)

Bergersen, Ove; Haarstad, Ketil

2014-01-01

Hydrogen sulphide (H2S) gas is a major odorant at municipal landfills. The gas can be generated from different waste fractions, for example demolition waste containing gypsum based plaster board. The removal of H2S from landfill gas was investigated by filtering it through mineral wool waste products. The flow of gas varied from 0.3 l/min to 3.0 l/min. The gas was typical for landfill gas with a mean H2S concentration of ca. 4500 ppm. The results show that the sulphide gas can effectively be removed by mineral wool waste products. The ratios of the estimated potential for sulphide precipitation were 19:1 for rod mill waste (RMW) and mineral wool waste (MWW). A filter consisting of a mixture of MWW and RMW, with a vertical perforated gas tube through the center of filter material and with a downward gas flow, removed 98% of the sulfide gas over a period of 80 days. A downward gas flow was more efficient in contacting the filter materials. Mineral wool waste products are effective in removing hydrogen sulphide from landfill gas given an adequate contact time and water content in the filter material. Based on the estimated sulphide removal potential of mineral wool and rod mill waste of 14 g/kg and 261 g/kg, and assuming an average sulphide gas concentration of 4500 ppm, the removal capacity in the filter materials has been estimated to last between 11 and 308 days. At the studied location the experimental gas flow was 100 times less than the actual gas flow. We believe that the system described here can be upscaled in order to treat this gas flow. Copyright © 2013 Elsevier Ltd. All rights reserved.

Hyaluronic Acid Graft Copolymers with Cleavable Arms as Potential Intravitreal Drug Delivery Vehicles.

Science.gov (United States)

Borke, Tina; Najberg, Mathie; Ilina, Polina; Bhattacharya, Madhushree; Urtti, Arto; Tenhu, Heikki; Hietala, Sami

2018-01-01

Treatment of retinal diseases currently demands frequent intravitreal injections due to rapid clearance of the therapeutics. The use of high molecular weight polymers can extend the residence time in the vitreous and prolong the injection intervals. This study reports a water soluble graft copolymer as a potential vehicle for sustained intravitreal drug delivery. The copolymer features a high molecular weight hyaluronic acid (HA) backbone and poly(glyceryl glycerol) (PGG) side chains attached via hydrolysable ester linkers. PGG, a polyether with 1,2-diol groups in every repeating unit available for conjugation, serves as a detachable carrier. The influence of synthesis conditions and incubation in physiological media on the molecular weight of HA is studied. The cleavage of the PGG grafts from the HA backbone is quantified and polymer-from-polymer release kinetics are determined. The biocompatibility of the materials is tested in different cell cultures. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Agrobacterium rhizogenes-induced cotton hairy root culture as an alternative tool for cotton functional genomics

Science.gov (United States)

Although well-accepted as the ultimate method for cotton functional genomics, Agrobacterium tumefaciens-mediated cotton transformation is not widely used for functional analyses of cotton genes and their promoters since regeneration of cotton in tissue culture is lengthy and labor intensive. In cer...

Antibacterial poly(lactic acid) (PLA) films grafting electrospun PLA/Ally isothioscyanate (AITC) fibers for food packaging

Science.gov (United States)

Poly(lactic acid) (PLA) fibers of submicron sizes encapsulating allyl isothiocyanate (AITC) (PfA) were made and electrospun onto the surfaces of PLA films (PfA-g-film). SEM examination confirmed that the fibers were grafted to the PLA film after the (PfA-g-film) underwent air blowing and water washi...

Cement bonded wood wool boards from podocarpus spp. for low ...

African Journals Online (AJOL)

... sound insulation in walls, ceilings and floors, roofs, sound barriers and thermal insulation. Further research is required to investigate the use of different wood species and different mineral binders. Keywords: podocarpus spp, wood-wool, wood-cement composites. Journal of Civil Engineering Research and Practice Vol.

Synthesis and Application of Acid Dyes Based on 3-(4-Aminophenyl-5-benzylidene-2-substituted phenyl-3, 5-dihydroimidazol-4-one

Directory of Open Access Journals (Sweden)

Devang N. Wadia

2008-01-01

Full Text Available A series of eight novel heterocyclic based monoazo acid dyes were synthesized using various substituted imidazol-4-one as diazo component and coupled with various amino-napthol sulphonic acids. The resultant dyes were characterized using standard spectroscopic methods and then dyeing performance on wool fabric was assessed. Final results concluded that exhaustion (%E of the dyes on wool fibers increased with decreasing pH of application and that fixation (%F of the dyes on wool fibers increased with increasing pH of application and the highest total fixation efficiency was achieved at pH 5. Wash and light fastness properties of prepared dyes showed encouraging results.

Graft copolymers of polypropylene films. 1. radiation induced grafting of mixed monomers. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

El-Salmawi, K M; El-Naggar, A M; Said, H M; Zahran, A H [Radiation Chemistry Department, National Center for Radiation Research and Technology, Atomic Energy Authority, Cairo, (Egypt)

1996-03-01

Radiation graft copolymerization of co monomer mixtures of acrylic acid (AAC), and styrene (S) onto polypropylene (PP) film by mutual method has been investigated. The effects of different factors that may affect the grafting yield such as inhibitor concentration (Mohr`s salt), solvent composition (MeOH and H{sub 2} O), radiation dose and dose rate were considered. It was found that the role of Mohr`s salt is very effective when the ratio of AAC in the co monomer mixtures was at lower values. However, the addition of 1.25 Wt% of Mohr`s salt reduced the homo polymer formation and enhances the grafting process. Graft copolymerization in presence of solvent mixture composed of methanol and water was found to afford higher grafting than in pure methanol regardless of the composition of the co monomer mixture used. However, the highest degree of grafting was obtained at a solvent composition of 20% H{sub 2} O:80%MeOH and a co monomer mixture of 20%AAC:80%sty. An attempt was made to determine each PAAC and PS fractions in the total graft yield obtained. Two methods of analysis based on using the reactivity ratios reported in literature, elemental analysis and IR spectroscopy. The determination of poly (acrylic acid) and polystyrene fractions by elemental analysis is believed more accurate than these by reactivity ratio. The precise results obtained by elemental analysis with respect to the chemical structure of known polymer prepared under identical conditions. The results obtained by IR measurements go well with that obtained with the reactivity ratio methods. 5 figs., 3 tabs.

Surface properties of calcium and magnesium oxide nanopowders grafted with unsaturated carboxylic acids studied with inverse gas chromatography.

Science.gov (United States)

Maciejewska, Magdalena; Krzywania-Kaliszewska, Alicja; Zaborski, Marian

2012-09-28

Inverse gas chromatography (IGC) was applied at infinite dilution to evaluate the surface properties of calcium and magnesium oxide nanoparticles and the effect of surface grafted unsaturated carboxylic acid on the nanopowder donor-acceptor characteristics. The dispersive components (γ(s)(D)) of the free energy of the nanopowders were determined by Gray's method, whereas their tendency to undergo specific interactions was estimated based on the electron donor-acceptor approach presented by Papirer. The calcium and magnesium oxide nanoparticles exhibited high surface energies (79 mJ/m² and 74 mJ/m², respectively). Modification of nanopowders with unsaturated carboxylic acids decreased their specific adsorption energy. The lowest value of γ(s)(D) was determined for nanopowders grafted with undecylenic acid, approximately 55 mJ/m². The specific interactions were characterised by the molar free energy (ΔG(A)(SP)) and molar enthalpy (ΔH(A)(SP)) of adsorption as well as the donor and acceptor interaction parameters (K(A), K(D)). Copyright © 2012 Elsevier B.V. All rights reserved.

A sustained release system using porous cellulose spheres modified by grafting as matrices

International Nuclear Information System (INIS)

Hosoi, Fumio; Makuuchi, Keizo; Saito, Kenji; Koishi, Masumi.

1987-01-01

Polymer-coated spheres, obtained by the graft polymerization of methyl methacrylate (MMA) onto porous spheres based on cellulose by the pre-irradiation method, were used as matrices for the drug sustained release system for salicylic acid. The adsorption of salicylic acid was carried out by dipping the grafted spheres in a 50% aqueous ethanol solution containing salicylic acid. The amount of salicylic acid adsorbed (Q) increased proportionately with the percent graft of MMA (G) to the power of 2.9. Adsorption mechanism of salicylic acid could be expressed in term of Langmuir's adsorption isotherm. The ratio of constants for adsorption and desorption (k) and the saturated amount of salicylic acid adsorbed (Q 0 ) were expressed as k = k 1 G and Q 0 = k 2 G 2.4 , respectively. These results indicate that the number of adsorption sites increased proportionately with the nth power of G as a results of the interaction of grafted poly (methyl methacrylate)(PMMA) and cellulose. Similar results were obtained with grafting of MMA, MMA-styrene (St), and MMA-methacrylic acid (MAc) in the presence of salicylic acid. (author)

Indian Bt cotton varieties do not affect the performance of cotton aphids.

Directory of Open Access Journals (Sweden)

Nora C Lawo

Full Text Available Cotton varieties expressing Cry proteins derived from the soil bacterium Bacillus thuringiensis (Bt are grown worldwide for the management of pest Lepidoptera. To prevent non-target pest outbreaks and to retain the biological control function provided by predators and parasitoids, the potential risk that Bt crops may pose to non-target arthropods is addressed prior to their commercialization. Aphids play an important role in agricultural systems since they serve as prey or host to a number of predators and parasitoids and their honeydew is an important energy source for several arthropods. To explore possible indirect effects of Bt crops we here examined the impact of Bt cotton on aphids and their honeydew. In climate chambers we assessed the performance of cotton aphids, Aphis gossypii Glover (Hemiptera: Aphididae when grown on three Indian Bt (Cry1Ac cotton varieties (MECH 12, MECH 162, MECH 184 and their non-transformed near isolines. Furthermore, we examined whether aphids pick up the Bt protein and analyzed the sugar composition of aphid honeydew to evaluate its suitability for honeydew-feeders. Plant transformation did not have any influence on aphid performance. However, some variation was observed among the three cotton varieties which might partly be explained by the variation in trichome density. None of the aphid samples contained Bt protein. As a consequence, natural enemies that feed on aphids are not exposed to the Cry protein. A significant difference in the sugar composition of aphid honeydew was detected among cotton varieties as well as between transformed and non-transformed plants. However, it is questionable if this variation is of ecological relevance, especially as honeydew is not the only sugar source parasitoids feed on in cotton fields. Our study allows the conclusion that Bt cotton poses a negligible risk for aphid antagonists and that aphids should remain under natural control in Bt cotton fields.

Isolation and Analysis of Keratins and Keratin-Associated Proteins from Hair and Wool.

Science.gov (United States)

Deb-Choudhury, Santanu; Plowman, Jeffrey E; Harland, Duane P

2016-01-01

The presence of highly cross-linked protein networks in hair and wool makes them very difficult substrates for protein extraction, a prerequisite for further protein analysis and characterization. It is therefore imperative that these cross-links formed by disulfide bridges are first disrupted for the efficient extraction of proteins. Chaotropes such as urea are commonly used as efficient extractants. However, a combination of urea and thiourea not only improves recovery of proteins but also results in improved resolution of the keratins in 2DE gels. Reductants also play an important role in protein dissolution. Dithiothreitol effectively removes keratinous material from the cortex, whereas phosphines, like Tris(2-carboxyethyl)phosphine, remove material from the exocuticle. The relative extractability of the keratins and keratin-associated proteins is also dependent on the concentration of chaotropes, reductants, and pH, thus providing a means to preferentially extract these proteins. Ionic liquids such as 1-butyl-3-methylimidazolium chloride (BMIM(+)[Cl](-)) are known to solubilize wool by disrupting noncovalent interactions, specifically intermolecular hydrogen bonds. BMIM(+)[Cl](-) proved to be an effective extractant of wool proteins and complementary in nature to chaotropes such as urea and thiourea for identifying unique peptides of wool proteins using mass spectrometry (MS). Successful identification of proteins resolved by one- or two-dimensional electrophoresis and MS is highly dependent on the optimal recovery of its protease-digested peptides with an efficient removal of interfering substances. The detergent sodium deoxycholate used in conjunction with Empore™ disks improved identification of proteins by mass spectrometry leading to higher percentage sequence coverage, identification of unique peptides and higher score. Copyright © 2016 Elsevier Inc. All rights reserved.

Experimental Study on the Comparison of the Material Properties of Glass Wool Used as Building Materials

Directory of Open Access Journals (Sweden)

Kyoung-Woo KIM

2014-04-01

Full Text Available Artificial mineral fibers such as glass wool or stone wool are commonly used in building walls, ceilings and floors as a major insulation material for buildings. Among the material properties of building materials, thermal conductivity, the sound absorption coefficient, compressibility, and dynamic stiffness are regarded as important performance requirements since they directly affect the thermal and acoustic properties of the building. This study measured the changes of the thermal and acoustical performances of glass wool that was actually installed for a long time to the outer wall of a building as an insulation material through a comparison with recently produced glass wool. The results showed that the measured thermal conductivities of the old and the new specimens both rise with an increase of temperature, showing quite similar results in both specimens over temperature ranges of (0 – 20 ºC. The noise reduction coefficient decreased by 0.1 in the old specimen and the difference of the compressibilities in both specimens was shown to be 7.32 mm. The dynamic stiffness of the old specimen was found to be 1.28 MN/m3 higher than that of the new specimen.DOI: http://dx.doi.org/10.5755/j01.ms.20.1.3714

DAPPA grafted polymer: an efficient solid phase extractant for U(VI), Th(IV) and La(III) from acidic waste streams and environmental samples.

Science.gov (United States)

Raju, Ch Siva Kesava; Subramanian, M S

2005-07-15

A new class of polymeric resin has been synthesized by grafting Merrifield chloromethylated resin with (dimethyl amino-phosphono-methyl)-phosphonic acid (MCM-DAPPA), for the preconcentration of U(VI), Th(IV) and La(III) from both acidic wastes and environmental samples. The various chemical modification steps involved during grafting process are characterized by FT-IR spectroscopy, (31)P and (13)C-CPMAS (cross-polarized magic angle spin) NMR spectroscopy and CHNS/O elemental analysis. The water regain capacity data for the grafted polymer are obtained from thermo-gravimetric (TG) analysis. The influence of various physico-chemical parameters during the quantitative extraction of metal ions by the resin phase are studied and optimized by both static and dynamic methods. The significant feature of this grafted polymer is its ability to extract both actinides and lanthanides from high-level acidities as well as from near neutral conditions. The resin shows very high sorption capacity values of 2.02, 0.89 and 0.54mmolg(-1) for U(VI), 1.98, 0.63 and 0.42mmolg(-1) for Th(IV) and 1.22, 0.39 and 0.39mmolg(-1) for La(III) under optimum pH, HNO(3) and HCl concentration, respectively. The grafted polymer shows faster phase exchange kinetics (99.5% recovery using 1M (NH(4))(2)CO(3), as eluent. The developed grafted resin has been successfully applied in extracting Th(IV) from high matrix monazite sand, U(VI) from sea water and also U(VI) and Th(IV) from simulated nuclear spent fuel mixtures. The analytical data obtained from triplicate measurements are within 3.9% R.S.D. reflecting the reproducibility and reliability of the developed method.

Position of Serbia on the international market of milk, dairy products, eggs and wool

Directory of Open Access Journals (Sweden)

Đorović Milutin

2011-01-01

Full Text Available This paper presents a comparative analysis of the major indicators of both world and domestic markets of milk, dairy products, eggs and wool. Namely, for the past 20 years, for the observed subperiods, the method of comparative analysis was used to study quantitative and structural differences in the production and trade of analyzed product groups, at both the world and at the level of continents and some countries. The leading manufacturers and flows of international trade and the leading exporters and importers of milk, dairy products, eggs and wool were defined, with special emphasis on importance of Serbia, i.e. its position in the global market for these products. Pursuant to the above, and importance of analyzed product groups for the domestic market, i.e. agroindustry and the economy as a whole, this paper specially studies balances, structure, dynamics and regional orientation of foreign trade in milk, dairy products, eggs and wool. In addition, the paper points to the needs, capabilities, measures and directions of further development of domestic production and export of products analyzed.

Radiation grafting of pH and thermosensitive N-isopropylacrylamide and acrylic acid onto PTFE films by two-steps process

International Nuclear Information System (INIS)

Bucio, E.; Burillo, G.

2007-01-01

Polytetrafluoroethylene (PTFE) was grafted (g) with acrylic acid (AAc) by γ-ray pre-irradiation method to get PTFE-g-AAc films, then N-isopropylacrylamide (NIPAAm) was grafted onto PTFE-g-AAc films with γ-ray to get (PTFE-g-AAc)-g-NIPAAm. PTFE films were irradiated in air at a dose rate of 3.0 kGy h -1 and different radiation dose. The irradiated films were placed in glass ampoules, which contained aqueous solutions with different monomer concentration (AAc), and then they were heated at different temperatures and reaction time. NIPAAm onto PTFE-g-AAc was carried out with the same procedure with monomer concentration of 1 mol L -1 . The thermosensitivity of the samples was defined and calculated as the ratio of the grafted samples swelling at 28 and 35 o C, and pH sensitivity defined as the ratio of the grafted samples swelling at pH 2 and 8

Fixation of some chemically modified reactive dye during gamma irradiation of cotton fabrics in presence of vinyl and acrylic monomers

International Nuclear Information System (INIS)

Zohdy, M.H.; El-Naggar, A.M.; Abdallah, W.A.

1999-01-01

The radiation grafting of vinyl sulfone dye having an activated double bond in presence of styrene monomer or its mixtures with ethyl acrylate onto cotton fabric has been investigated. The chemical reaction of the vinyl sulfone form with peroxy radicals on cotton fabric through covalent bonding is tested by extracting the dyed samples in 50% aqueous DMF solution. It was found that the presence of styene monomer in the dyeing solution is essential for the reaction or grafting of the vinyl sulfone dye. However, when a constant styrene concentration of 5% was used in the dye bath, the color strength expressed as K/S was found to increase by increasing the dye concentration. The results showed that the color strength obtained in case of using 10% ethyl acrylate is much lower than in the case of using the same concentration of styrene monomer. A solvent composition of equal ratios of methanol and water has been proven to be suitable to produce the highest improvement in the color strength. The irradiation dose was found to play an important role in initiating the reaction of the vinyl sulfone dye

Radiation grafting of pH-sensitive acrylic acid and 4-vinyl pyridine onto nylon-6 using one- and two-step methods

International Nuclear Information System (INIS)

Ortega, Alejandra; Alarcón, Darío; Muñoz-Muñoz, Franklin; Garzón-Fontecha, Angélica; Burillo, Guillermina

2015-01-01

Acrylic acid (AAc) and 4-vinyl pyridine (4VP) were γ-ray grafted onto nylon-6 (Ny 6 ) films via pre-irradiation oxidative method. These monomers were grafted using a one-step method to render Ny 6 -g–(AAc/4VP). A two-step or sequential method was used to render (Ny 6 -g–AAc)-g–4VP. Random copolymer branches were obtained when the grafting was carried out via one-step method using the two monomers together. The two-step method was applied to graft chains of 4VP on both Ny 6 substrate and previously grafted AAc chains (Ny 6 -g–AAc). The two types of binary copolymers synthesized were characterized to determine the amount of grafted polymers, the thermal behavior (DSC and TGA), the surface composition (XPS), and the pH responsiveness. In the two-step process, it is possible to achieve a higher graft yield, better control of the amount of each monomer, good reversibility in the swelling/deswelling process and shorter time to achieve equilibrium swelling. - Highlights: • A new binary graft of 4VP and AAc onto Ny 6 films was synthesized by γ-radiation. • The binary grafted material has potential application for heavy ion retention. • The two-step method shows better conditions in swelling and reversibility properties. • Surface distribution of monomers was evaluate by XPS characterization

Dictionary of cotton: Picking & ginning

Science.gov (United States)

Cotton is an essential commodity for textiles and has long been an important item of trade in the world’s economy. Cotton is currently grown in over 100 countries by an estimated 100 producers. The basic unit of the cotton trade is the cotton bale which consists of approximately 500 pounds of raw c...

Effect of gamma rays on nucleic acids content (RNA and DNA) of the cotton leaf worm Spodoptera Littoralis (BOISD). Vol. 4

International Nuclear Information System (INIS)

Sallam, H.A.; El-Shall, S.A.; Sobeiha, A.K.; El-Bamby, M.A.

1996-01-01

Full grown pupae of the cotton leaf worm Spodoptera Littoralis (Boisd) were exposed to exposed to sub sterilizing doses of 100, 200 and 300 Gy gamma radiation. The changes in nucleic acids content (RNA and DNA) of irradiated pupae, after 24 hours from irradiation, and also in 3 days old adults resulting from irradiated pupae were investigated. The total nucleic acids content in either pupae or adults was progressively reduced as the dose was increased. The reduction of both RNA and DNA in females was greater than in males. DNA was more radiosensitive than RNA. The destructive action of irradiation on nucleic acids was more pronounced in adult stage. Irradiation increased the RNA/DNA ratio than control at all treatments for female pupae at 200 Gy. 2 tabs

Effect of gamma rays on nucleic acids content (RNA and DNA) of the cotton leaf worm Spodoptera Littoralis (BOISD). Vol. 4.

Energy Technology Data Exchange (ETDEWEB)

Sallam, H A; El-Shall, S A [Biological Applications Department, Nuclear Research Center, Atomic Energy Authority, Cairo (Egypt); Sobeiha, A K; El-Bamby, M A [Plant Protection Department, Faculty of Agriculture, Ain Shams University, Cairo (Egypt)

1996-03-01

Full grown pupae of the cotton leaf worm Spodoptera Littoralis (Boisd) were exposed to exposed to sub sterilizing doses of 100, 200 and 300 Gy gamma radiation. The changes in nucleic acids content (RNA and DNA) of irradiated pupae, after 24 hours from irradiation, and also in 3 days old adults resulting from irradiated pupae were investigated. The total nucleic acids content in either pupae or adults was progressively reduced as the dose was increased. The reduction of both RNA and DNA in females was greater than in males. DNA was more radiosensitive than RNA. The destructive action of irradiation on nucleic acids was more pronounced in adult stage. Irradiation increased the RNA/DNA ratio than control at all treatments for female pupae at 200 Gy. 2 tabs.

PREPARATION OF ACTIVATED CARBON FROM SILK COTTON WOOD AND COCONUT SHELL BY PYROLISIS WITH CERAMIC FURNACE

Directory of Open Access Journals (Sweden)

Winarto Haryadi

2010-06-01

Full Text Available Preparation of activated carbon from silk cotton wood and coconut shell has been done. Carbon was made by pyrolysis process in the Muchalal furnace with 3000 watt electric power. The electric power was increased gradually from 1000, 2000 and then 3000 watt with interval 2 hours during 7 hours. Carbon was activated in Muchalal furnace with 4000 watt electric power during 2 hours and flowed with nitrogen gas. Product of the activated carbon was compared to standart product with several analysis including the surface area, acetic acid adsorption, iod adsorption and vapour adsorption. The results of analysis showed that surface area for silk cotton wood carbon, coconut shell carbon, and E.Merck product were 288.8072 m2/g, 222.9387 m2/g and 610.5543 m2/g, respectively. Acetic acid adsorption for silk cotton wood carbon, coconut shell carbon, and standart product were 157.391 mg/g, 132.791 mg/g, and 186.911 mg/g, respectively. Iodine adsorption for cotton wood carbon, coconut shell carbon, and standart product were 251.685 mg/g, 207.270 mg/g and 310.905 mg/g, respectively. Vapour adsorption for cotton wood carbon, coconut shell carbon and standart product were 12%, 4%,and 14%., respectively Key words : Activated carbon, pyrolysis, Muchalal furnace

The halo effect: suppression of pink bollworm on non-Bt cotton by Bt cotton in China.

Directory of Open Access Journals (Sweden)

Peng Wan

Full Text Available In some previously reported cases, transgenic crops producing insecticidal proteins from Bacillus thuringiensis (Bt have suppressed insect pests not only in fields planted with such crops, but also regionally on host plants that do not produce Bt toxins. Here we used 16 years of field data to determine if Bt cotton caused this "halo effect" against pink bollworm (Pectinophora gossypiella in six provinces of the Yangtze River Valley of China. In this region, the percentage of cotton hectares planted with Bt cotton increased from 9% in 2000 to 94% in 2009 and 2010. We found that Bt cotton significantly decreased the population density of pink bollworm on non-Bt cotton, with net decreases of 91% for eggs and 95% for larvae on non-Bt cotton after 11 years of Bt cotton use. Insecticide sprays targeting pink bollworm and cotton bollworm (Helicoverpa armigera decreased by 69%. Previously reported evidence of the early stages of evolution of pink bollworm resistance to Bt cotton in China has raised concerns that if unchecked, such resistance could eventually diminish or eliminate the benefits of Bt cotton. The results reported here suggest that it might be possible to find a percentage of Bt cotton lower than the current level that causes sufficient regional pest suppression and reduces the risk of resistance.

Fluorescent boronic acid terminated polymer grafted silica particles synthesized via click chemistry for affinity separation of saccharides

Energy Technology Data Exchange (ETDEWEB)

Xu, Zhifeng, E-mail: 897061147@qq.com; Deng, Peihong; Tang, Siping; Li, Junhua

2014-07-01

Boronic acids are important for effective separation of biological active cis-diols. For the purpose of constructing a new type of saccharide-sensitive material which can not only provide convenient separation but also improve the access of boronic acid to guest molecules, the fluorogenic boronic acid terminated, thermo-sensitive polymers (BA-polyNIPAm) were grafted to an alkyne modified silica gel through the exploitation of click chemistry. The BA-polyNIPAm grafted silica gel (BA-polyNIPAm-SG) was characterized by FT-IR, fluorescence spectra, fluorescence microscopy, elemental analysis (EA), thermal gravimetric analysis (TGA), scanning electron microscope (SEM) and so on. BA-polyNIPAm-SG displayed affinity binding ability for saccharides under physiological pH value and allowed saccharides to be conveniently separated from solution. The maximum binding capacities for fructose and glucose are 83.2 μmol/g and 70.4 μmol/g polymer, respectively. The intensity of fluorescence emission of BA-polyNIPAm-SG increased with the increasing of fructose concentration. The present study provides a new kind of composite material which contains moveable and flexible grippers for recognizing and binding guest molecules. - Highlights: • Fluorogenic boronic acid terminated polymers were conjugated to silica particle. • The prepared material can conveniently separate saccharides from solution. • The prepared material displays increased fluorescence emission upon binding fructose.

Fluorescent boronic acid terminated polymer grafted silica particles synthesized via click chemistry for affinity separation of saccharides

International Nuclear Information System (INIS)

Xu, Zhifeng; Deng, Peihong; Tang, Siping; Li, Junhua

2014-01-01

Boronic acids are important for effective separation of biological active cis-diols. For the purpose of constructing a new type of saccharide-sensitive material which can not only provide convenient separation but also improve the access of boronic acid to guest molecules, the fluorogenic boronic acid terminated, thermo-sensitive polymers (BA-polyNIPAm) were grafted to an alkyne modified silica gel through the exploitation of click chemistry. The BA-polyNIPAm grafted silica gel (BA-polyNIPAm-SG) was characterized by FT-IR, fluorescence spectra, fluorescence microscopy, elemental analysis (EA), thermal gravimetric analysis (TGA), scanning electron microscope (SEM) and so on. BA-polyNIPAm-SG displayed affinity binding ability for saccharides under physiological pH value and allowed saccharides to be conveniently separated from solution. The maximum binding capacities for fructose and glucose are 83.2 μmol/g and 70.4 μmol/g polymer, respectively. The intensity of fluorescence emission of BA-polyNIPAm-SG increased with the increasing of fructose concentration. The present study provides a new kind of composite material which contains moveable and flexible grippers for recognizing and binding guest molecules. - Highlights: • Fluorogenic boronic acid terminated polymers were conjugated to silica particle. • The prepared material can conveniently separate saccharides from solution. • The prepared material displays increased fluorescence emission upon binding fructose

Selective adsorption of Pb (II) ions by amylopectin-g-poly (acrylamide-co-acrylic acid): A bio-degradable graft copolymer.

Science.gov (United States)

Sasmal, Dinabandhu; Maity, Jayanta; Kolya, Haradhan; Tripathy, Tridib

2017-04-01

Amylopectin-g-poly (acrylamide-co-acrylic acid) [AP-g-poly (AM-co-AA)] was synthesised in water medium by using potassium perdisulphate as an initiator. The graft copolymer was characterized by molecular weight determination by size exclusion chromatography (SEC), fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR) spectroscopy, scanning electron microscope (SEM) studies, thermal analysis, measurement of neutralisation equivalent and biodegradation studies. The graft copolymer was used for Pb (II) ion removal from aqueous solution. The Pb (II) ion removal capacity of the graft copolymer was also compared with another laboratory developed graft copolymer Amylopectin-g-poly (acrylamide) (AP-g-PAM). Both the graft copolymers were also used for the competitive metal ions removal with Pb (II)/Cd (II), Pb (II)/Zn (II), Pb (II)/Ni (II), Pb (II)/Cu (II) pairs separately under similar conditions. AP-g-poly (AM-co-AA) showed better Pb (II) ion adsorbing power over AP-g-PAM and also much selective towards Pb (II) ions. The adsorption follows a second order rate equation and Langmuir isotherm model. Copyright © 2017 Elsevier B.V. All rights reserved.

Graft copolymerization of water soluble mixed monomers onto polyethylene by the pre-irradiation method

International Nuclear Information System (INIS)

Long Fu; Tang Liming; Zhao Jin; Gao Zhenyong

1993-01-01

Grafting of water soluble mixed monomers of acrylic acid (AA)/acrylamide (Am) and acrylic acid/methacrylic acid (MA) onto polyethylene film by the pre-irradiation grafting method was investigated. The results showed that the grafting proceeded successfully with the adding of ferric salt in the solution. In the case of AA/Am system, a synergistic effect was noticed. In the case of AA/MA system, the graft percent increased with the increase in the concentration of MA in the feed ratio. Furthermore, the effects of monomer concentration, radiation dose and temperature on the grafting were also studied

Eco-friendly finishing agent for cotton fabrics to improve flame retardant and antibacterial properties.

Science.gov (United States)

El-Shafei, A; ElShemy, M; Abou-Okeil, A

2015-03-15

This research work deals with flame retardant and antibacterial finishing agent for cellulosic fabrics using TiO2 nanoparticles and chitosan phosphate. TiO2 nanoparticles were prepared by sol-gel method using titanium tetraisopropoxide. The size of TiO2 nanoparticles was characterized using transmission electron microscope (TEM). The application of nano TiO2 onto cellulosic fabrics (cotton 100%) was achieved in presence of polycarboxylic acid [1,2,3,4-butane tetracarboxylic acid (BTCA)] with sodium hypophosphite (SHP) as catalyst and chitosan phosphate through conventional pad-dry-cure method. The effect of the finishing on the physical properties, flammability and antibacterial properties of cross-linked fabrics are investigated. Thermal gravimetric analysis (TGA) was employed to investigate the thermal decomposition behaviour of the treated samples. Limited oxygen indexes (LOI) of the treated cotton fabrics were investigated. The treated cotton fabric also reveals excellent antibacterial properties. Copyright © 2014 Elsevier Ltd. All rights reserved.

Astronaut Clothing for Exploration Missions

Science.gov (United States)

Poritz, Darwin H.; Orndoff, Evelyne; Kaspranskiy, Rustem R.; Schesinger, Thilini; Byrne, Vicky

2016-01-01

Astronaut clothes for exploration missions beyond low Earth orbit need to satisfy several challenges not met by the currently-used mostly-cotton clothing. A laundering system is not expected to be available, and thus soiled garments must be trashed. Jettisoning waste does not seem feasible at this time. The cabin oxygen concentration is expected to be higher than standard, and thus fabrics must better resist ignition and burning. Fabrics need to be identified that reduce logistical mass, that can be worn longer before disposal, that are at least as comfortable as cotton, and that resist ignition or that char immediately after ignition. Human factors and psychology indicate that crew well-being and morale require a variety of colors and styles to accommodate personal identity and preferences. Over the past four years, the Logistics Reduction Project under NASA's Advanced Exploration Systems Program has sponsored the Advanced Clothing System Task to conduct several ground studies and one ISS study. These studies have evaluated length of wear and personal preferences of commercially-available exercise- and routine-wear garments made from several fabrics (cotton, polyester, Merino wool, and modacrylic), woven and knitted. Note that Merino wool and modacrylic char like cotton in ambient air, while polyester unacceptably melts. This paper focuses on the two components of an International Space Station study, onboard and on the ground, with astronauts and cosmonauts. Fabrics were randomized to participants. Length of wear was assessed by statistical survival analysis, and preference by exact binomial confidence limits. Merino wool and modacrylic t-shirts were worn longer on average than polyester t-shirts. Interestingly, self-assessed preferences were inconsistent with length-of-wear behavior, as polyester was preferred to Merino wool and modacrylic.

antimicrobial properties of some natural and synthetic fabrics modified by radiation treatments

International Nuclear Information System (INIS)

Mohamed, R.M.A.

2008-01-01

natural and synthetic fabrics have been treated with different antimicrobial metal complexes under the effect of gamma radiation . in this regard, cotton, cotton/PET blend and PET were grafted with acrylic acid by gamma radiation and this grafted fabrics were complexed with Cu(ll),Ni(ll)and Co(ll) metal ions . the antimicrobial properties were evaluated by the measurement of tensile strength of fabrics after burring in a soil for one and two weeks as well as the effect of this treatment on the growth of certain bacteria and fungi incubated on a culture for 48 hours. the results showed that the highest protection to cotton, cotton/PET blend and PET fabrics by using Cu(ll) ion in the complexation process, where the order of protection by metals is Cu(ll) > Co(ll)> Ni(ll), moreover, the more grafted fabrics the more complexed fabrics with metal ions and is higher protection against microorganisms . the treatment with the metal ions has nearly no effect on the chemical and physical properties of the natural or the synthetic fabrics as indicated from the analysis by TGA, sem, ion exchange testing and wettability testing.

Biosynthesis of nano cupric oxide on cotton using Seidlitzia rosmarinus ashes utilizing bio, photo, acid sensing and leaching properties.

Science.gov (United States)

Bashiri Rezaie, Ali; Montazer, Majid; Rad, Mahnaz Mahmoudi

2017-12-01

In this research, a facile, rapid and eco-friendly method is introduced for synthesis and loading of cupric oxide on cellulosic chains of cotton fabric with functional properties. Seidlitzia rosmarinus ashes and copper acetate were employed as a natural source of alkaline and metal salt without further chemical materials. The treated samples indicated very good antibacterial activities toward both pathogen Staphylococcus aureus as Gram-positive and Escherichia coli as Gram-negative bacteria. Significant self-cleaning properties against degradation of methylene blue stain under UV irradiation were found. The sensing properties of high concentrated inorganic and organic acids such as sulfuric and formic acids based on colorimetric alterations of the treated fabrics were also confirmed showing acid leaching effects of the treated fabrics. Further, the treated samples showed coloring effects with an enhancement on the physio-mechanical properties including tensile strength, crease recovery angle and hydrophobocity. Copyright © 2017 Elsevier Ltd. All rights reserved.

Detecting mismatches in the phenology of cotton bollworm larvae and cotton flowering in response to climate change

Science.gov (United States)

Huang, Jian; Hao, HongFei

2018-05-01

Current evidence suggests that climate change has directly affected the phenology of many invertebrate species associated with agriculture. Such changes in phenology have the potential to cause temporal mismatches between predators and prey and may lead to a disruption in natural pest control ecosystem. Understanding the synchrony between pest insects and host plant responses to climate change is a key step to improve integrated pest management strategies. Cotton bollworm larvae damage cotton, and thus, data from Magaiti County, China, collected during the period of 1990-2015 were analyzed to assess the effects of climate change on cotton bollworm larvae and cotton flowering. The results showed that a warming climate advanced the phenology of cotton bollworm larvae and cotton flowering. However, the phenological rate of change was faster in cotton bollworm larvae than that in cotton flowering, and the larval period was prolonged, resulting in a great increase of the larval population. The abrupt phenological changes in cotton bollworm larvae occurred earlier than that in cotton, and the abrupt phenological changes in cotton flowering occurred earlier than that in larval abundance. However, the timing of abrupt changes in larval abundance all occurred later than that in temperature. Thus, the abrupt changes that occurred in larvae, cotton flowering and climate were asynchronous. The interval days between the cotton flowering date (CFD) and the half-amount larvae date (HLD) expanded by 3.41 and 4.41 days with a 1 °C increase of T mean in May and June, respectively. The asynchrony between cotton bollworm larvae and cotton flowering will likely broaden as the climate changes. The effective temperature in March and April and the end date of larvae (ED) were the primary factors affecting asynchrony.

Detecting mismatches in the phenology of cotton bollworm larvae and cotton flowering in response to climate change.

Science.gov (United States)

Huang, Jian; Hao, HongFei

2018-05-11

Current evidence suggests that climate change has directly affected the phenology of many invertebrate species associated with agriculture. Such changes in phenology have the potential to cause temporal mismatches between predators and prey and may lead to a disruption in natural pest control ecosystem. Understanding the synchrony between pest insects and host plant responses to climate change is a key step to improve integrated pest management strategies. Cotton bollworm larvae damage cotton, and thus, data from Magaiti County, China, collected during the period of 1990-2015 were analyzed to assess the effects of climate change on cotton bollworm larvae and cotton flowering. The results showed that a warming climate advanced the phenology of cotton bollworm larvae and cotton flowering. However, the phenological rate of change was faster in cotton bollworm larvae than that in cotton flowering, and the larval period was prolonged, resulting in a great increase of the larval population. The abrupt phenological changes in cotton bollworm larvae occurred earlier than that in cotton, and the abrupt phenological changes in cotton flowering occurred earlier than that in larval abundance. However, the timing of abrupt changes in larval abundance all occurred later than that in temperature. Thus, the abrupt changes that occurred in larvae, cotton flowering and climate were asynchronous. The interval days between the cotton flowering date (CFD) and the half-amount larvae date (HLD) expanded by 3.41 and 4.41 days with a 1 °C increase of T mean in May and June, respectively. The asynchrony between cotton bollworm larvae and cotton flowering will likely broaden as the climate changes. The effective temperature in March and April and the end date of larvae (ED) were the primary factors affecting asynchrony.

Cotton transformation via pollen tube pathway.

Science.gov (United States)

Wang, Min; Zhang, Baohong; Wang, Qinglian

2013-01-01

Although many gene transfer methods have been employed for successfully obtaining transgenic cotton, the major constraint in cotton improvement is the limitation of genotype because the majority of transgenic methods require plant regeneration from a single transformed cell which is limited by cotton tissue culture. Comparing with other plant species, it is difficult to induce plant regeneration from cotton; currently, only a limited number of cotton cultivars can be cultured for obtaining regenerated plants. Thus, development of a simple and genotype-independent genetic transformation method is particularly important for cotton community. In this chapter, we present a simple, cost-efficient, and genotype-independent cotton transformation method-pollen tube pathway-mediated transformation. This method uses pollen tube pathway to deliver transgene into cotton embryo sacs and then insert foreign genes into cotton genome. There are three major steps for pollen tube pathway-mediated genetic transformation, which include injection of -foreign genes into pollen tube, integration of foreign genes into plant genome, and selection of transgenic plants.

Genetic correlations among and between wool, growth and reproduction traits in Merino sheep.

Science.gov (United States)

Safari, E; Fogarty, N M; Gilmour, A R; Atkins, K D; Mortimer, S I; Swan, A A; Brien, F D; Greeff, J C; van der Werf, J H J

2007-04-01

Data from seven research resource flocks across Australia were combined to provide accurate estimates of genetic correlations among production traits in Merino sheep. The flocks represented contemporary Australian Merino fine, medium and broad wool strains over the past 30 years. Over 110,000 records were available for analysis for each of the major wool traits, and 50,000 records for reproduction and growth traits with over 2700 sires and 25,000 dams. Individual models developed from the single trait analyses were extended to the various combinations of two-trait models to obtain genetic correlations among six wool traits [clean fleece weight (CFW), greasy fleece weight, fibre diameter (FD), yield, coefficient of variation of fibre diameter and standard deviation of fibre diameter], four growth traits [birth weight, weaning weight, yearling weight (YWT), and hogget weight] and four reproduction traits [fertility, litter size, lambs born per ewe joined, lambs weaned per ewe joined (LW/EJ)]. This study has provided for the first time a comprehensive matrix of genetic correlations among these 14 wool, growth and reproduction traits. The large size of the data set has also provided estimates with very low standard errors. A moderate positive genetic correlation was observed between CFW and FD (0.29 +/- 0.02). YWT was positively correlated with CFW (0.23 +/- 0.04), FD (0.17 +/- 0.04) and LWEJ (0.58 +/- 0.06), while LW/EJ was negatively correlated with CFW (-0.26 +/- 0.05) and positively correlated with FD (0.06 +/- 0.04) and LS (0.68 +/- 0.04). These genetic correlations, together with the estimates of heritability and other parameters provide the basis for more accurate prediction of outcomes in complex sheep-breeding programmes designed to improve several traits.

Live mass, carcass and wool growth responses to supplementation ...

African Journals Online (AJOL)

(KOK) teen peile van 0, 100 of 200 g/d in kombinasie met heel mielies teen. 0, 100 of 200 g/d as byvoeding tot 'n dieet van koringstrooi plus ureum vir SA Vleismerino- ... the optimum level of nutrition for live mass-gain and wool growth in terms of protein to energy ratios by supplying nutrients via the abomasum, either by ...

Investigation of the Development of Farming Professional Cooperatives of Cashmere-goat and Wool-sheep in China

OpenAIRE

SHI, Jing; XIAO, Haifeng

2013-01-01

Based on the data from the survey of cashmere-goat and wool-sheep in 12 demonstration counties of China’s main producing areas in 2012, the development of farming professional cooperatives of cashmere-goat and wool-sheep was analyzed from aspects of status quo, problems and causes, and some suggestions about cooperation cognition and mode, service capacity, personnel training, system improvement and preferential policies were put forward to promote the development of the farming professiona...

16 CFR 300.25 - Country where wool products are processed or manufactured.

Science.gov (United States)

2010-01-01

... an origin label on the unfinished product, the manufacturing processes as required in paragraph (a)(4... processed or manufactured. Further work or material added to the wool product in another country must effect...

16 CFR 1.63 - Injunctions: Wool, fur, and textile cases.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Injunctions: Wool, fur, and textile cases. 1.63 Section 1.63 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF... be to the public interest for it to do so, the Commission will apply to the courts for injunctive...

Radiation graft post-polymerization of sodium styrene sulfonate onto polyethylene

International Nuclear Information System (INIS)

Kitaeva, N.K.; Duflot, V.R.; Ilicheva, N.S.

2013-01-01

Post-irradiation grafting of sodium styrene sulfonate (SSS) in the presence of acrylic acid (AA) has been investigated on polyethylene (PE) pre-exposed to gamma radiation at room temperature in the air. Special attention was paid to the effect of low molecular weight salt additives on the kinetics of graft copolymerization of SSS and AA. The presence of SSS links in the grafted PE copolymers was detected by the methods of UV and FTIR spectroscopy. Based on the FTIR spectroscopy and element analysis data, a mechanism was proposed for graft copolymerization of SSS and AA onto PE. The mechanical properties of the graft copolymers were studied. It was established that PE copolymers grafted with sulfonic acid and carboxyl groups have higher strength characteristics (16.3 MPa) compared to the samples containing only carboxyl groups (11 MPa). (author)

Sandwich-panels based on penopolisocyanurate and mineral wool

OpenAIRE

Burtzeva M.; Mednikova E.

2017-01-01

Sandwich panel is a self-supporting structure consisting of two steel zinc-coated profiles with a layer of heat retainer. It is used as roofing and walling material. Widely is used in industrial construction, shopping centres, sports complexes, chilling and freezing chambers, storage buildings and quickly erectable housing. The classical basis of heat-insulating layer (core panel) products is used mineral wool insulation materials. This material is resistant to deformation, non-flammable,...

The effect of layer-by-layer chitosan-hyaluronic acid coating on graft-to-bone healing of a poly(ethylene terephthalate) artificial ligament.

Science.gov (United States)

Li, Hong; Ge, Yunsheng; Zhang, Pengyun; Wu, Lingxiang; Chen, Shiyi

2012-01-01

Surface coating with an organic layer-by-layer self-assembled template of chitosan and hyaluronic acid on a poly(ethylene terephthalate) (PET) artificial ligament was designed for the promotion and enhancement of graft-to-bone healing after artificial ligament implantation in a bone tunnel. The results of in vitro culturing of MC3T3-E1 mouse osteoblastic cells supported the hypothesis that the layer-by-layer coating of chitosan and hyaluronic acid could promote the cell compatibility of grafts and could promote osteoblast proliferation. A rabbit extra-articular tendon-to-bone healing model was used to evaluate the effect of this kind of surface-modified stainless artificial ligament in vivo. The final results proved that this organic compound coating could significantly promote and enhance new bone formation at the graft-bone interface histologically and, correspondingly, the experimental group with coating had significantly higher biomechanical properties compared with controls at 8 weeks (P < 0.05).

Radiation grafting on natural films

International Nuclear Information System (INIS)

Lacroix, M.; Khan, R.; Senna, M.; Sharmin, N.; Salmieri, S.; Safrany, A.

2014-01-01

Different methods of polymer grafting using gamma irradiation are reported in the present study for the preparation of newly functionalized biodegradable films, and some important properties related to their mechanical and barrier properties are described. Biodegradable films composed of zein and poly(vinyl alcohol) (PVA) were gamma-irradiated in presence of different ratios of acrylic acid (AAc) monomer for compatibilization purpose. Resulting grafted films (zein/PVA-g-AAc) had their puncture strength (PS=37–40 N mm −1 ) and puncture deformation (PD=6.5–9.8 mm) improved for 30% and 50% PVA in blend, with 5% AAc under 20 kGy. Methylcellulose (MC)-based films were irradiated in the presence of 2-hydroxyethyl methacrylate (HEMA) or silane, in order to determine the effect of monomer grafting on the mechanical properties of films. It was found that grafted films (MC-g-HEMA and MC-g-silane) using 35% monomer performed higher mechanical properties with PS values of 282–296 N mm −1 and PD of 5.0–5.5 mm under 10 kGy. Compatibilized polycaprolactone (PCL)/chitosan composites were developed via grafting silane in chitosan films. Resulting trilayer grafted composite film (PCL/chitosan-g-silane/PCL) presented superior tensile strength (TS=22 MPa) via possible improvement of interfacial adhesion (PCL/chitosan) when using 25% silane under 10 kGy. Finally, MC-based films containing crystalline nanocellulose (CNC) as a filling agent were prepared and irradiated in presence of trimethylolpropane trimethacrylate (TMPTMA) as a grafted plasticizer. Grafted films (MC-g-TMPTMA) presented superior mechanical properties with a TS of 47.9 MPa and a tensile modulus (TM) of 1792 MPa, possibly due to high yield formation of radicals to promote TMPTMA grafting during irradiation. The addition of CNC led to an additional improvement of the barrier properties, with a significant 25% reduction of water vapor permeability (WVP) of grafted films. - Highlights: • Irradiation of zein

Preparation of Dimethylaminoethylmethacrylate Grafted Polymeric Adsorbent by Using Radiation-Induced Grafting Technique for Removal of Anions

International Nuclear Information System (INIS)

Kavakli, P. A.

2006-01-01

The development of efficient separation and purification techniques is very important from industrial, environmental and economic points of view. Polymeric materials having polyfunctional groups such as carboxylic, amide, nitrile, iminodiacetic acid, amidoxime, and ammonium groups, etc., not only possess good hydrophilic properties, but also have good ion exchange properties which make them suitable for metal recovery from aqueous solutions. Radiation induced grafting is a powerful technique capable of controlling the introduction of various functional groups to the polymeric materials, keeping the original properties and especially the mechanical strength of the base material, and thus, allowing the synthesis of more stable polymeric adsorbents. The main objective of this study was to develop special polymeric adsorbents to remove NOx and PO 4 anions from aqueous systems. For this purpose, a novel nonwoven fabric was prepared by radiation-induced graft polymerization of imethylaminoethylmethacrylate (DMAEMA) onto polypropylene coated polyethylene nonwoven fabric. The trunk polymer was irradiated by electron beam at a voltage of 2 MeV and a current of 3 mA in a nitrogen atmosphere at dry-ice temperature at different doses. The degree of grafting was determined as a function of the total dose, monomer concentration, temperature, and reaction time. It was found that the degree of grafting of grafted polymer was greatly affected by reaction conditions. Grafting conditions were optimized, and about 150 % degree of grafting samples was used for further experiments. DMAEMA grafted polymer was later protonated by using acid solution to prepare adsorbent for the removal of anions. Adsorption experiments were performed in column mode for removal of phosphate. Approximately 2000 bed volumes of phosphate-free water can be produced from 10 ppb phosphate solution at high space velocity

A marketing and promotion strategy for wool | van Wyk | South ...

African Journals Online (AJOL)

South African Journal of Animal Science. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 10, No 2 (1980) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register. A marketing and promotion strategy for wool.

Effects of Elevated Carbon Dioxide on the Growth and Foliar Chemistry of Transgenic Bt Cotton

Institute of Scientific and Technical Information of China (English)

Gang Wu; Fa-Jun Chen; Feng Ge; Yu-Cheng Sun

2007-01-01

A field study was carried out to quantify plant growth and the foliar chemistry of transgenic Bacillus thuringiensis (Bt)cotton (cv. GK-12) exposed to ambient CO2 and elevated (double-ambient) CO2 for different lengths of time (1, 2 and 3 months) in 2004 and 2005. The results indicated that CO2 levels significantly affected plant height, leaf area per plant and leaf chemistry of transgenic Bt cotton. Significantly, higher plant height and leaf area per plant were observed after cotton plants that were grown in elevated CO2 were compared with plants grown in ambient CO2 for 1, 2 and 3 months in the investigation. Simultaneously, significant interaction between CO2 level x investigating year was observed in leaf area per plant. Moreover, foliar total amino acids were increased by 14%, 13%, 11% and 12%, 14%, 10% in transgenic Bt cotton after exposed to elevated CO2 for 1, 2 or 3 months compared with ambient CO2 in 2004 and 2005, respectively. Condensed tannin occurrence increased by 17%, 11%, 9% in 2004 and 12%, 11%, 9% in 2005 in transgenic Bt cotton after being exposed to elevated CO2 for 1, 2 or 3 months compared with ambient CO2 for the same time. However, Bt toxin decreased by 3.0%,2.9%, 3.1% and 2.4%, 2.5%, 2.9% in transgenic Bt cotton after exposed to elevated CO2 for 1, 2 or 3months compared with ambient CO2 for same time in 2004 and 2005, respectively. Furthermore, there was prominent interaction on the foliar total amino acids between the CO2 level and the time of cotton plant being exposed to elevated CO2. It is presumed that elevated CO2 can alter the plant growth and hence ultimately the phenotype allocation to foliar chemistical components of transgenic Bt cotton, which may in turn, affect the plant-herbivore interactions.

THE ANALYSIS OF CORRELATIONS BETWEEN THE MAIN TRAITS OF WOOL PRODUCTION ON PALAS SHEEP LINE FOR MEAT, MILK AND HIGH PROLIFICACY

Directory of Open Access Journals (Sweden)

ANA ENCIU

2008-10-01

Full Text Available The aim of this paper was to analyze the coefficient of phenotypic correlation and regression between main wool production traits for the sheep belonging to the Palas line specialized for meat, milk and with high prolificacy. The study was performed on a 10 years interval, the phenotypic correlation and the regression being determined for age groups and body weight classes for the following traits: raw wool production, the staple length, wool diameter and body weight at shearing. The obtained results are showing that for the specialized sheep lines the efficiency of wool production is also higher for the sheep with moderate body weights but for these sheep lines the selection for body weight will be done based on the morphoproductive parameters specific to the purpose of exploitation (milk production, meat production or high prolificacy.

Analysis of Fundus Photography and Fluorescein Angiography in Nonarteritic Anterior Ischemic Optic Neuropathy and Optic Neuritis.

Science.gov (United States)

Kim, Min Kyung; Kim, Ungsoo Samuel

2016-08-01

We evaluated fundus and fluorescein angiography (FAG) findings and characteristics that can help distinguish nonarteritic anterior ischemic optic neuropathy (NAION) from optic neuritis (ON). Twenty-three NAION patients and 17 ON with disc swelling patients were enrolled in this study. We performed fundus photography and FAG. The disc-swelling pattern, hyperemia grade, presence of splinter hemorrhages, cotton-wool spots, artery/vein ratio and degree of focal telangiectasia were investigated. The FAG findings for each patient were compared with respect to the following features: the pattern of disc leakage in the early phase, arteriovenous (artery/vein) transit time (second), and the presence and pattern of the filling delay. Cotton-wool spots, focal telangiectasia, and venous congestion were more common in the affected eyes of NAION patients. Upon FAG, 76.5% of the patients in the ON group exhibited normal choroidal circulation. However, 56.5% of patients in the NAION group demonstrated abnormal filling defects, such as peripapillary, generalized, or watershed zone filling delays. Fundus findings, including cotton-wool spots, focal telangiectasia, and venous congestion in the affected eye, may be clues that can be used to diagnose NAION. In addition, choroidal insufficiencies on FAG could be also helpful in differentiating NAION from ON.

STUDY ON MORPHOLOGICAL AND STRUCTURAL CHANGES INDUCED BY ULTRASONIC DEGR EASING OF WOOL AND HUMAN HAIR WASTES

Directory of Open Access Journals (Sweden)

BĂLĂU MÎNDRU Tudorel

2014-05-01

Full Text Available Recovery and reuse of wool and hair waste is a challenge with the ultimate goal environment protection. One of the early stages of the recovery process is the operation of scouring-degreasing wool and human hair waste. In recent decades the use of ultrasound technology has established an important place in different industrial processes and has started to revolutionize environmental protection. The power of ultrasound can enhance a wide variety of chemical and physical processes, mainly due to the phenomenon known as cavitation in a liquid medium. The objective of the present work is to develop eco-friendly effective degreasing system for keratin fiber waste with the aid of ultrasound, using distilled water and also trichlorethylene as a medium of propagation-degreasing, and realized a comparative analysis of efficiency of fat extraction by Soxhlet classical method and via ultrasonication. This work investigate the effect that ultrasonic irradiation has on the structure of wool and hair fibers. Thus were highlighted both morphological and structural changes of treated materials using optical microscopy, and FTIR spectroscopy. By using the unconventional method of cleaning and degreasing with an ultrasonic resonator tube are possible reductions in utility and solvents consumption together with changes in the cuticular layer of wool and hair fibers.

Benzimidazole grafted polybenzimidazoles for proton exchange membrane fuel cells

DEFF Research Database (Denmark)

Yang, Jingshuai; Aili, David; Li, Qingfeng

2013-01-01

High molecular weight polybenzimidazole (PBI) was synthesized and grafted with benzimidazole pendant groups. The high molecular weight of PBI resulted in good film-forming properties and superior tensile strength. With a phosphoric acid doping level (ADL) of 13.1, a tensile strength of 16 MPa...... was achieved at room temperature. Grafting of benzimidazole moieties onto the PBI macromolecular chain introduced additional basic sites which allowed the membrane to achieve higher phosphoric acid uptakes. A molar acid conductivity, defined as the specific conductivity of each mole of doping acid...

Chrysanthemum cutting productivity and rooting ability are improved by grafting.

Science.gov (United States)

Zhang, Jing; Chen, Sumei; Liu, Ruixia; Jiang, Jiafu; Chen, Fadi; Fang, Weimin

2013-01-01

Chrysanthemum has been commercially propagated by rooting of cuttings, whereas the quality will decline over multiple collections from a single plant. Therefore, we compared the vigour, rooting ability, and some physiological parameters between cuttings harvested from nongrafted "Jinba" (non-grafted cuttings) with those collected from grafted "Jinba" plants onto Artemisia scoparia as a rootstock (grafted cuttings). The yield, length, node number, stem diameter, fresh weight, and dry weight of the grafted cuttings were superior to the non-grafted cuttings. Also grafted cuttings "Jinba" rooted 1 day earlier, but showing enhanced rooting quality including number, length, diameter, and dry weight of roots, where compared to the non-grafted. The physiological parameters that indicated contents of soluble protein, peroxidase activity, soluble sugar, and starch, ratios of soluble sugar/nitrogen ratio, and carbohydrate/nitrogen (C/N), as well as contents of indole-3-acetic acid (IAA) and abscisic acid (ABA), and IAA/ABA ratio were significantly increased in the grafted cuttings. This suggested their important parts in mediating rooting ability. Results from this study showed that grafting improved productivity and rooting ability related to an altered physiology, which provide a means to meet the increasing demand.

A Note on the Dyeing of Wool Fabrics Using Natural Dyes Extracted from Rotten Wood-Inhabiting Fungi

Directory of Open Access Journals (Sweden)

Vicente A. Hernández

2018-02-01

Full Text Available Fungal isolates obtained from rotten wood samples were identified and selected by their ability to produce fungal dyes in liquid media. Fungal isolates produced natural extracellular dyes with colors ranging from red to orange, yellow and purple. Dyes from two of these fungi, Talaromyces australis (red and Penicillium murcianum (yellow, were extracted and used to dye wool samples in a Data Color Ahiba IR Pro-Trade (model Top Speed II machine. The protein nature of wool interacted well with the fungal dyes producing colors suitable for textile applications when used to a concentration of 0.1 g·L−1. Results on color fastness when washing confirmed the affinity of the dyes with wool as the dyed samples kept their color in acceptable ranges after washing, without the implementation of mordanting pretreatments or the use of fixing agents.

Preparation, properties and biological application of pH-sensitive poly(ethylene oxide) (PEO) hydrogels grafted with acrylic acid(AAc) using gamma-ray irradiation

International Nuclear Information System (INIS)

Nho, Y.C.; Mook Lim, Youn; Moo Lee, Young

2004-01-01

pH-sensitive hydrogels were studied as a drug carrier for the protection of insulin from the acidic environment of the stomach before releasing it in the small intestine. In this study, hydrogels based on poly(ethylene oxide) (PEO) networks grafted with acrylic acid (AAc) were prepared via a two-step process. PEO hydrogels were prepared by γ-ray irradiation, and then grafting by AAc monomer onto the PEO hydrogels with the subsequent irradiation (radiation dose: 5-20 kGy, dose rate: 2.15 kGy/h). These grafted hydrogels showed a pH-sensitive swelling behavior. The grafted hydrogels were used as a carrier for the drug delivery systems for the controlled release of insulin. The in vitro drug release behaviors of these hydrogels were examined by quantification analysis with a UV/VIS spectrophotometer. Insulin was loaded into freeze-dried hydrogels (7 mmx3 mmx2.5 mm) and administrated orally to healthy and diabetic Wistar rats. The oral administration of insulin-loaded hydrogels to Wistar rats decreased the blood glucose levels obviously for at least 4 h due to the absorption of insulin in the gastrointestinal tract

Biodiesel and biohydrogen production from cotton-seed cake in biorefinery concept

NARCIS (Netherlands)

Panagiotopoulos, I.A.; Pasias, S.; Bakker, R.R.C.; Vrije, de G.J.; Papayannakos, N.; Claassen, P.A.M.; Koukios, E.G.

2013-01-01

Biodiesel production from cotton-seed cake (CSC) and the pretreatment of the remaining biomass for dark fermentative hydrogen production was investigated. The direct conversion to biodiesel with alkali free fatty acids neutralization pretreatment and alkali transesterification resulted in a

Determination of ABA-binding proteins contents in subcellular fractions isolated from cotton seedlings using radioimmunoanalysis

International Nuclear Information System (INIS)

Tursunkhodjayeva, F.M.

2004-01-01

Full text: Knowledge of plants' hormone receptor sites is essential to understanding of the principles of phytohormone action in cells and tissues. The hormone abscisic acid (ABA) takes part in many important physiological processes of plants, including water balance and resistance to salt stress. The detection of salt tolerance in the early stages of ontogenesis is desirable for effective cultivation of cotton. Usually such characteristics are determined visually after genetic analysis of hybrids over several generations. This classic method of genetics requires a long time to grow several generations of cotton plants. In this connection we study ABA-binding protein contents in subcellular fractions isolated from seedlings of several kinds of cotton with different tolerance to salt stress. The contents of ABA-binding protein in nuclei and chloroplasts fractions isolated from cotton seedlings were determined using radioimmunoanalysis. The subcellular fractions were prepared by ultracentrifugation in 0,25 - 2,2 M sucrose gradient. ABA-binding protein was isolated from cotton seedlings by affinity chromatography. The antibodies against ABA-binding protein of cotton were developed in rabbits according standard protocols. Than the antibodies were labelled by radioisotope J 125 according Greenwood et al. It was shown, that the nuclei and chloroplasts fractions isolated from cotton with high tolerance to salt stress contain ABA-binding protein up to 1,5-1,8 times more, than the same fractions from cotton with low tolerance to salt stress. So, the ABA-binding protein contents in cotton seedlings may be considered as a marker for screening of cotton kinds, which may potentially have high tolerance to salt stress

Identification of a New Cotton Disease Caused by an Atypical Cotton Leafroll Dwarf Virus in Argentina.

Science.gov (United States)

Agrofoglio, Yamila C; Delfosse, Verónica C; Casse, María F; Hopp, Horacio E; Kresic, Iván Bonacic; Distéfano, Ana J

2017-03-01

An outbreak of a new disease occurred in cotton (Gossypium hirsutum) fields in northwest Argentina starting in the 2009-10 growing season and is still spreading steadily. The characteristic symptoms of the disease included slight leaf rolling and a bushy phenotype in the upper part of the plant. In this study, we determined the complete nucleotide sequences of two independent virus genomes isolated from cotton blue disease (CBD)-resistant and -susceptible cotton varieties. This virus genome comprised 5,866 nucleotides with an organization similar to that of the genus Polerovirus and was closely related to cotton leafroll dwarf virus, with protein identity ranging from 88 to 98%. The virus was subsequently transmitted to a CBD-resistant cotton variety using Aphis gossypii and symptoms were successfully reproduced. To study the persistence of the virus, we analyzed symptomatic plants from CBD-resistant varieties from different cotton-growing fields between 2013 and 2015 and showed the presence of the same virus strain. In addition, a constructed full-length infectious cDNA clone from the virus caused disease symptoms in systemic leaves of CBD-resistant cotton plants. Altogether, the new leafroll disease in CBD-resistant cotton plants is caused by an atypical cotton leafroll dwarf virus.

Antimicrobial-impregnated dressing combined with negative-pressure wound therapy increases split-thickness skin graft engraftment: a simple effective technique.

Science.gov (United States)

Wu, Cheng-Chun; Chew, Khong-Yik; Chen, Chien-Chang; Kuo, Yur-Ren

2015-01-01

Immobilization and adequate surface contact to wounds are critical for skin graft take. Techniques such as the tie-over dressing, cotton bolster, and vacuum-assisted closure are used to address this, but each has its limitations. This study is designed to assess the effect of antimicrobial-impregnated dressing (AMD) combined with negative-pressure wound therapy (NPWT) on skin graft survival. Retrospective case-control study : Patients with chronic or contaminated wounds treated with split-thickness skin graft. A broad spectrum of wounds was included, from causes such as trauma, burns, chronic diabetic ulcers, and infection. Antimicrobial-impregnated dressing, which contains 0.2% polyhexamethylene biguanide, with NPWT MAIN OUTCOME MEASURE:: Success of skin graft : In the AMD group, all skin grafts achieved 100% take without secondary intervention. No infection or graft failure was observed in any patients, and no complications, such as hematoma or seroma formation, were noted, although in the control group partial loss of skin grafts was noted in 3 patients. Infection and inadequate immobilization were thought to be the main reasons. There were no hematoma or seroma formations in the control group. Use of an AMD dressing with NPWT after split-thickness skin grafting can be an effective method to ensure good graft to wound contact and enhances skin graft take in chronic and contaminated wounds.

Superoleophobic cotton textiles

NARCIS (Netherlands)

Leng, B.; Shao, Z.; With, de G.; Ming, W.

2009-01-01

Common cotton textiles are hydrophilic and oleophilic in nature. Superhydrophobic cotton textiles have the potential to be used as self-cleaning fabrics, but they typically are not super oil-repellent. Poor oil repellency may easily compromise the self-cleaning property of these fabrics. Here, we

7 CFR 1205.319 - Cotton-producing region.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Cotton-producing region. 1205.319 Section 1205.319... Cotton Research and Promotion Order Definitions § 1205.319 Cotton-producing region. Cotton-producing region means each of the following groups of cotton-producing States: (a) Southeast Region: Alabama...

The promise of a specially-designed graft copolymer of acrylic acid onto cellulose as selective sorbent for heavy metal ions.

Science.gov (United States)

Essawy, Hisham A; Mohamed, Magdy F; Ammar, Nabila S; Ibrahim, Hanan S

2017-10-01

A specially-designed graft copolymer of acrylic acid onto in-situ formed cellulose-fulvate hybrid showed privileged tendency for uptake of Pb(II) during competitive removal from a mixture containing Cd(II) and Ni(II) within 5min at pH 5. This novel trend is attributed mainly to the crowded high content of coordinating centers within the designed graft copolymer along with the acquired superabsorbency. This provides an outstanding tool to separate some metal ions selectively from mixtures containing multiple ions on kinetic basis. Thus, the designed graft copolymer structure exhibited superior efficiency that reached ∼95% for sole removal of Pb(II). Kinetic modeling for Pb(II) individual removal showed excellent fitting with a pseudo second-order model. Intraparticle diffusion model on the other hand ensured governance of boundary layer effect over diffusion during the removal process due to the superabsorbency feature of the graft copolymer. The experimental findings were described with models such as Freundlich, Langmuir, and Dubinin-Radushkevich. The Langmuir and Freundlich models showed convenience with the adsorption isotherm of Pb(II) onto the developed graft copolymer. Copyright © 2017 Elsevier B.V. All rights reserved.

Examining cotton in rotation with rice and cotton in rotation with other crops using natural experiment

Science.gov (United States)

Sun, Ling; Zhu, Zesheng

2017-08-01

This paper is to show the ability of remote sensing image analysis combined with statistical analysis to characterize the environmental risk assessment of cotton in rotation with rice and cotton in rotation with other crops in two ways: (1) description of rotation period of cotton in rotation with rice and cotton in rotation with other crops by the observational study or natural experiment; (2) analysis of rotation period calculation of cotton in rotation with rice and cotton in rotation with other crops. Natural experimental results show that this new method is very promising for determining crop rotation period for estimating regional averages of environmental risk. When it is applied to determining crop rotation period, two requested remote sensing images of regional crop are required at least.

Radiation grafting of acrylamide and maleic acid on chitosan and effective application for removal of Co(II) from aqueous solutions

Science.gov (United States)

Saleh, Alaaeldine Sh.; Ibrahim, Ahmed G.; Elsharma, Emad M.; Metwally, Essam; Siyam, Tharwat

2018-03-01

The graft copolymerization has been proven as a superior polymerization technique because it combines the functional advantages of the grafted and base polymers. In this work, the radiation-induced grafting of acrylamide (AAm) and maleic acid (MA) onto chitosan (CTS) was developed and optimized by determining the grafting percentage and efficiency as a function of grafting conditions such as AAm, MA, and CTS concentrations, and absorbed dose. Fourier transform infrared spectroscopic analysis (FTIR) confirmed the graft copolymerization. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) further characterized the grafted copolymers and showed their high thermal stability. Using batch sorption experiments and 60Co as a radiotracer, poly(CTS-AAm) and poly(CTS-MA) were evaluated for Co(II) removal from aqueous solutions. The Co(II) removal increases with increasing time, pH, polymer, and Co(II) concentrations. Experimentally, P(CTS-AAm) and P(CTS-MA) show high sorption capacities of Co(II), i.e. 150 mg g-1 and 421 mg g-1, respectively, which makes them potential sorbents of Co(II) for water and wastewater treatment. Finally, the Co(II) sorption was examined using sorption isotherm and kinetic models. The sorption was best fitted to Langmuir model which suggests the sorption is of chemisorption type. On the other hand, the sorption kinetics was best represented by Elovich model which also indicates the chemical nature of Co(II) sorption on P(CTS-AAm) and P(CTS-MA).

Transgenic cotton expressing Cry10Aa toxin confers high resistance to the cotton boll weevil.

Science.gov (United States)

Ribeiro, Thuanne Pires; Arraes, Fabricio Barbosa Monteiro; Lourenço-Tessutti, Isabela Tristan; Silva, Marilia Santos; Lisei-de-Sá, Maria Eugênia; Lucena, Wagner Alexandre; Macedo, Leonardo Lima Pepino; Lima, Janaina Nascimento; Santos Amorim, Regina Maria; Artico, Sinara; Alves-Ferreira, Márcio; Mattar Silva, Maria Cristina; Grossi-de-Sa, Maria Fatima

2017-08-01

Genetically modified (GM) cotton plants that effectively control cotton boll weevil (CBW), which is the most destructive cotton insect pest in South America, are reported here for the first time. This work presents the successful development of a new GM cotton with high resistance to CBW conferred by Cry10Aa toxin, a protein encoded by entomopathogenic Bacillus thuringiensis (Bt) gene. The plant transformation vector harbouring cry10Aa gene driven by the cotton ubiquitination-related promoter uceA1.7 was introduced into a Brazilian cotton cultivar by biolistic transformation. Quantitative PCR (qPCR) assays revealed high transcription levels of cry10Aa in both T 0 GM cotton leaf and flower bud tissues. Southern blot and qPCR-based 2 -ΔΔCt analyses revealed that T 0 GM plants had either one or two transgene copies. Quantitative and qualitative analyses of Cry10Aa protein expression showed variable protein expression levels in both flower buds and leaves tissues of T 0 GM cotton plants, ranging from approximately 3.0 to 14.0 μg g -1 fresh tissue. CBW susceptibility bioassays, performed by feeding adults and larvae with T 0 GM cotton leaves and flower buds, respectively, demonstrated a significant entomotoxic effect and a high level of CBW mortality (up to 100%). Molecular analysis revealed that transgene stability and entomotoxic effect to CBW were maintained in T 1 generation as the Cry10Aa toxin expression levels remained high in both tissues, ranging from 4.05 to 19.57 μg g -1 fresh tissue, and the CBW mortality rate remained around 100%. In conclusion, these Cry10Aa GM cotton plants represent a great advance in the control of the devastating CBW insect pest and can substantially impact cotton agribusiness. © 2017 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

Comparative Biomechanical and Microstructural Analysis of Native versus Peracetic Acid-Ethanol Treated Cancellous Bone Graft

Science.gov (United States)

Rauh, Juliane; Despang, Florian; Baas, Jorgen; Liebers, Cornelia; Pruss, Axel; Günther, Klaus-Peter; Stiehler, Maik

2014-01-01

Bone transplantation is frequently used for the treatment of large osseous defects. The availability of autologous bone grafts as the current biological gold standard is limited and there is a risk of donor site morbidity. Allogenic bone grafts are an appealing alternative, but disinfection should be considered to reduce transmission of infection disorders. Peracetic acid-ethanol (PE) treatment has been proven reliable and effective for disinfection of human bone allografts. The purpose of this study was to evaluate the effects of PE treatment on the biomechanical properties and microstructure of cancellous bone grafts (CBG). Forty-eight human CBG cylinders were either treated by PE or frozen at −20°C and subjected to compression testing and histological and scanning electron microscopy (SEM) analysis. The levels of compressive strength, stiffness (Young's modulus), and fracture energy were significantly decreased upon PE treatment by 54%, 59%, and 36%, respectively. Furthermore, PE-treated CBG demonstrated a 42% increase in ultimate strain. SEM revealed a modified microstructure of CBG with an exposed collagen fiber network after PE treatment. We conclude that the observed reduced compressive strength and reduced stiffness may be beneficial during tissue remodeling thereby explaining the excellent clinical performance of PE-treated CBG. PMID:24678514

Comparative biomechanical and microstructural analysis of native versus peracetic acid-ethanol treated cancellous bone graft.

Science.gov (United States)

Rauh, Juliane; Despang, Florian; Baas, Jorgen; Liebers, Cornelia; Pruss, Axel; Gelinsky, Michael; Günther, Klaus-Peter; Stiehler, Maik

2014-01-01

Bone transplantation is frequently used for the treatment of large osseous defects. The availability of autologous bone grafts as the current biological gold standard is limited and there is a risk of donor site morbidity. Allogenic bone grafts are an appealing alternative, but disinfection should be considered to reduce transmission of infection disorders. Peracetic acid-ethanol (PE) treatment has been proven reliable and effective for disinfection of human bone allografts. The purpose of this study was to evaluate the effects of PE treatment on the biomechanical properties and microstructure of cancellous bone grafts (CBG). Forty-eight human CBG cylinders were either treated by PE or frozen at -20 °C and subjected to compression testing and histological and scanning electron microscopy (SEM) analysis. The levels of compressive strength, stiffness (Young's modulus), and fracture energy were significantly decreased upon PE treatment by 54%, 59%, and 36%, respectively. Furthermore, PE-treated CBG demonstrated a 42% increase in ultimate strain. SEM revealed a modified microstructure of CBG with an exposed collagen fiber network after PE treatment. We conclude that the observed reduced compressive strength and reduced stiffness may be beneficial during tissue remodeling thereby explaining the excellent clinical performance of PE-treated CBG.

Comparative Biomechanical and Microstructural Analysis of Native versus Peracetic Acid-Ethanol Treated Cancellous Bone Graft

Directory of Open Access Journals (Sweden)

Juliane Rauh

2014-01-01

Full Text Available Bone transplantation is frequently used for the treatment of large osseous defects. The availability of autologous bone grafts as the current biological gold standard is limited and there is a risk of donor site morbidity. Allogenic bone grafts are an appealing alternative, but disinfection should be considered to reduce transmission of infection disorders. Peracetic acid-ethanol (PE treatment has been proven reliable and effective for disinfection of human bone allografts. The purpose of this study was to evaluate the effects of PE treatment on the biomechanical properties and microstructure of cancellous bone grafts (CBG. Forty-eight human CBG cylinders were either treated by PE or frozen at −20°C and subjected to compression testing and histological and scanning electron microscopy (SEM analysis. The levels of compressive strength, stiffness (Young’s modulus, and fracture energy were significantly decreased upon PE treatment by 54%, 59%, and 36%, respectively. Furthermore, PE-treated CBG demonstrated a 42% increase in ultimate strain. SEM revealed a modified microstructure of CBG with an exposed collagen fiber network after PE treatment. We conclude that the observed reduced compressive strength and reduced stiffness may be beneficial during tissue remodeling thereby explaining the excellent clinical performance of PE-treated CBG.

Early warning of cotton bollworm resistance associated with intensive planting of Bt cotton in China.

Directory of Open Access Journals (Sweden)

Haonan Zhang

Full Text Available Transgenic crops producing Bacillus thuringiensis (Bt toxins kill some key insect pests, but evolution of resistance by pests can reduce their efficacy. The predominant strategy for delaying pest resistance to Bt crops requires refuges of non-Bt host plants to promote survival of susceptible pests. To delay pest resistance to transgenic cotton producing Bt toxin Cry1Ac, farmers in the United States and Australia planted refuges of non-Bt cotton, while farmers in China have relied on "natural" refuges of non-Bt host plants other than cotton. Here we report data from a 2010 survey showing field-evolved resistance to Cry1Ac of the major target pest, cotton bollworm (Helicoverpa armigera, in northern China. Laboratory bioassay results show that susceptibility to Cry1Ac was significantly lower in 13 field populations from northern China, where Bt cotton has been planted intensively, than in two populations from sites in northwestern China where exposure to Bt cotton has been limited. Susceptibility to Bt toxin Cry2Ab did not differ between northern and northwestern China, demonstrating that resistance to Cry1Ac did not cause cross-resistance to Cry2Ab, and implying that resistance to Cry1Ac in northern China is a specific adaptation caused by exposure to this toxin in Bt cotton. Despite the resistance detected in laboratory bioassays, control failures of Bt cotton have not been reported in China. This early warning may spur proactive countermeasures, including a switch to transgenic cotton producing two or more toxins distinct from Cry1A toxins.

Lignin-rich biomass of cotton by-products for biorefineries via pyrolysis.

Science.gov (United States)

Chen, Jiao; Liang, Jiajin; Wu, Shubin

2016-10-01

Pyrolysis was demonstrated to investigate the thermal decomposition characteristics and potential of lignin-rich cotton by-products cotton exocarp (CE) and spent mushroom substrate consisted of cotton by-products (MSC) for biorefineries. The chemical component and structure alteration of CE and MSC was found to affect their thermochemical behaviors. The bio-oil yield from CE was 58.13wt% while the maximum yield from MSC was 45.01% at 600°C. The phenolic compounds obtained from CE and MSC were 33.9% and 39.2%, respectively. The yield of acetic acid from MSC between 400 and 600°C was about 30-38% lower than that from CE, which suggests the high quality of bio-oil was obtained. Biochar from MSC via slow pyrolysis had a high mass yield (44.38wt%) with well-developed pore structure. Copyright © 2016 Elsevier Ltd. All rights reserved.

STUDY OF THE INFLUENCE OF SYNTHETIC COMPONENT IN MIXTURES WITH WOOL ON THE PHYSICAL-MECHANICAL PROPRIETIES

Directory of Open Access Journals (Sweden)

OANA Dorina

2016-05-01

Full Text Available The main physical-mechanical properties of the yarns are: linear density (Tex, tensile strength, tenacity, elongation at break, twisting and mechanical work of fracture, there is a strong correlation between them. The tensile properties are the basic characteristics of yarns, influencing how they behave in the technological processes of mechanical processing (preparation for weaving or knitting, proper weaving or knitting determining the technological parameters of equipment adjusting during the technological processes and also their productivity. The tensile properties of yarns constitute qualitative characteristics, because their value depends on the quality of the yarn and also on the finite product obtained from processing yarns. In this paper was done a comparative study of the tensile properties of two batches of mixed woolen yarns (wool with polyester and wool with polyamide, the mixture being in the same proportions, but the yarns have different fineness and have very close twist values, both batches of yarns were designed for knitted products. Batch I consists of 70% wool yarns and 30% polyester, linear density Ttex = 55.56 tex and twist of 350 twists/meter. Batch II consists of 70% wool yarns and 30% polyamide, a linear density of Ttex = 71.34 tex and twist of 330 twists/meter (so a thicker yarn than the one from batch I. Following the analysis between the two batches is clear that the woolen yarns in batch II have much higher tensile properties.

Chemical hydrogels based on a hyaluronic acid-graft-α-elastin derivative as potential scaffolds for tissue engineering.

Science.gov (United States)

Palumbo, Fabio Salvatore; Pitarresi, Giovanna; Fiorica, Calogero; Rigogliuso, Salvatrice; Ghersi, Giulio; Giammona, Gaetano

2013-07-01

In this work hyaluronic acid (HA) functionalized with ethylenediamine (EDA) has been employed to graft α-elastin. In particular a HA-EDA derivative bearing 50 mol% of pendant amino groups has been successfully employed to produce the copolymer HA-EDA-g-α-elastin containing 32% w/w of protein. After grafting with α-elastin, remaining free amino groups reacted with ethylene glycol diglycidyl ether (EGDGE) for producing chemical hydrogels, proposed as scaffolds for tissue engineering. Swelling degree, resistance to chemical and enzymatic hydrolysis, as well as preliminary biological properties of HA-EDA-g-α-elastin/EGDGE scaffold have been evaluated and compared with a HA-EDA/EGDGE scaffold. The presence of α-elastin grafted to HA-EDA improves attachment, viability and proliferation of primary rat dermal fibroblasts and human umbilical artery smooth muscle cells. Biological performance of HA-EDA-g-α-elastin/EGDGE scaffold resulted comparable to that of a commercial collagen type I sponge (Antema®), chosen as a positive control. Copyright © 2013 Elsevier B.V. All rights reserved.

The Impacts of U.S. Cotton Programs on the West and Central African Countries Cotton Export Earnings

OpenAIRE

Fadiga, Mohamadou L.; Mohanty, Samarendu; Pan, Suwen

2005-01-01

This study uses a stochastic simulation approach based on a partial equilibrium structural econometric model of the world fiber market to examine the effects of a removal of U.S. cotton programs on the world market. The effects on world cotton prices and African export earnings were analyzed. The results suggest that on average an elimination of U.S. cotton programs would lead to a marginal increase in the world cotton prices thus resulting in minimal gain for cotton exporting countries in Af...

Pilot study on using an alternative method of estimating emission of heavy metals from wood combustion

Science.gov (United States)

Olszowski, Tomasz; Bożym, Marta

2014-09-01

This thesis presents pilot studies concerning the assessment of the possibility of using organic materials of vegetative origin as indices of heavy metals emissions (Cd, Cr, Cu, Ni, Pb and Zn) from domestic wood-fired fireplaces. Mosses of the Pleurozium schreberi species as well as cellulose and cotton wool were used during the study as the potential indices for the elements emission. It was proved that mosses are more reliable as indices of metals emissions than cellulose or cotton wool. It was found that the quantity of Ni accumulated in the moss tissue is comparable with the concentration of this compound in the dust assessed with the reference method. A correlation between the Ni, Cr, Zn and Pb concentrations defined in the mosses and dust filter was found. It was proved that mosses as adsorbers, more clearly than in the case of cellulose and cotton, react to the change of the size of the particulates emitted.

Polymer additives for improving performance properties of cotton fabric crosslinked with 1,2,3,4 butanetetracarboxylic acid

International Nuclear Information System (INIS)

Refaie, R.

2005-01-01

1,2,3,4 butanetetracarboxylic acid (BTCA) represents an environmental safe alternative for commercial formaldehyde containing resins that acquire cotton textile easy care properties. However, several draw-back are encountered with BTCA finishing treatment, like excessive fabric tendering, yellowing as well as lower dye affinity. The feasibility of adding different polymers, viz-polyethylene glycol 600 (PEG), polyvinyl alcohol, and carboxymethyl cellulose (CMC), alone or in admixture with chitosan to the finishing bath containing BTCA was investigated. Moreover, cationized forms of these polymers were also used as additives in the finishing formulation containing BTCA. Results obtained of CMC alone or with chitosan (0.5 %), with BTCA finishing formulation improves Cease Recovery Angle, Tensile strength, as well as basic dye ability compared with or without additives

Locally Grown: Examining Attitudes and Perceptions About Organic Cotton Production and Manufacturing Between Mississippi Cotton Growers and Consumers

Directory of Open Access Journals (Sweden)

Charles Freeman

2016-06-01

Full Text Available The purpose of this study is to examine attitudes and perceptions about organic cotton of Mississippi cotton growers and producers in comparison to fashion-conscious consumers, including advantages/disadvantages of growing and production processes, quality control, consumer preferences, and competitive price structures/profit margins. A sample size of 16 local Mississippi growers and/or producers and 44 undergraduate students at a mid-major Southeastern university were chosen to participate in the study. Instruments were developed based on current research and the definition of organic cotton production defined by the United States Department of Agriculture. Results indicate 75% of growers and producers do not perceive a quality difference between organic and conventionally grown cotton, while 72.7% of the consumers report organically grown cotton is capable of producing a higher quality product compared to conventionally grown cotton. Even with an increase in organic cotton prices (25- 40% higher premium, only 25% of growers and producers would be willing to convert, while a majority (52.3% of consumers would not be willing to spend more than 25% extra for an organically grown cotton product. Consumers indicate the negative effects of conventionally grown cotton, yet many report little knowledge about organic cotton production, while growers/producers immediately dismiss organically grown cotton as a retail marketing strategy.

Insolubilisation of biologically active materials with novel radiation graft copolymers

International Nuclear Information System (INIS)

Garnett, J.L.; Jankiewicz, S.V.; Levot, R.; Sangster, D.F.

1984-01-01

The use of radiation grafting to immobilise a typical enzyme, trypsin, is reported. The technique involves radiation grafting to a backbone polymer a monomer containing an appropriate functional group to which the enzyme is bonded. In the present work, p-nitrostyrene has been grafted to representative trunk polymers, polypropylene and PVC, the nitro group in the resulting copolymer converted to the isothiocyanato derivative to which trypsin is attached. Of importance to this insolubilisation process, especially for radiation sensitive backbone polymers, is the inclusion of additives which enhance grafting. A new class of additives which increase the grafting yields is reported using as representative backbone polymers, naturally occurring cellulose and synthetic low density polyethylene. The new additives are specific metal salts such as LiClO 4 . The reactivity of these salts in grafting enhancement has been compared with that of mineral acid which has previously been used as an additive to increase grafting yields in both preirradiation and simultaneous techniques. A new model for grafting enhancement in the presence of the metal salts as well as acids is proposed whereby increased grafting yields are attributed to increased partitioning of monomer into the graft region in the presence of ionic solutes. The value of these additives in preparing copolymers suitable for general reagent insolubilisation reactions is discussed

Late-onset persistent retinal microvascular changes after bone marrow transplantation: 3-year follow-up

Directory of Open Access Journals (Sweden)

Muccioli Cristina

2002-01-01

Full Text Available Purpose: To describe a case of persistent retinopathy after bone marrow transplantation in the absence of radiation therapy. Methods: Case Report. Results: A 42 year-old man developed bilateral visual loss 15 months after receiving a bone marrow transplant for acute leukemia. The patient was treated with a high dose of cyclosporin A and oral corticosteroids. No radiation therapy was given. Late-onset, multiple, bilateral cotton-wool spots developed 15 months after the bone marrow transplantation and still persist. After three years other cotton-wool spots arose in the absence of any immunosuppressive therapy. Conclusions: Bone marrow transplantation microvasculopathy of the retina may be related to certain combinations of chemotherapy drugs or immunosuppression itself and may persist in the absence of these immunosuppressive drugs.

Miliaria in Neonates at a South-West Nigerian, State Hospital ...

African Journals Online (AJOL)

Also, of the non-over clothed babies, 48 were dressed in cotton while the remaining 76 were either dressed in, polyester, wool or silk fabric. Miliaria was present in 10 (20.8%) of the 48 babies dressed in cotton compared, with the corresponding 59(77.6%) of the remaining 76 babies. ÷2= 37.88, P= 0.00. Of the 118 mothers ...

Improving the quality of wool through the use of gene markers ...

African Journals Online (AJOL)

Results also indicated that the keratin genes on chromosome 11 are recombining relatively frequently at recombination "hotspots". It appears as though genes coding for the KRTs and KAPs have the potential to impact on wool quality and could potentially be exploited in gene marker-assisted selection programmes in the ...

Removal of Industrial Pollutants From Wastewater's By Graft Copolymers

International Nuclear Information System (INIS)

Hegazy El-Sayed, A.; El-Nagar Abdel-Wahab, M.; Senna Magdy, M.; Zahran Abdel-Hamid, H.

1999-01-01

Graft copolymers that obtained by radiation grafting of acrylic acid and acrylamide onto LDPE film were converted to N-hydroxy ethyl amide and hydroxamic acid derivatives respectively. The possible application for the different prepared chemical derivatives of LDPE graft copolymers in metal adsorption from solutions containing a single cation or simulated medium active waste has been investigated. The results showed that the adsorption of Cu(II) metal by different chemical derivatives was greatly affected by different factors such as graft yield, ph value, concentration of metal in the feed solution, immersion time and treatment temperature. The affinity of N-hydroxy ethyl amide derivative toward the different metals was found to be in the order of; Cu(II) >Pd(II) > Cd(II)> Co(II). However, for hydroxamic acid derivative , the affinity order was: Cd(II) > Cu(II) > Co(II). The ESR and IR analysis revealed that the metal ions are chelated through the lone pair of electrons on the -OH and -NH- groups forming a ring structure. The measured metal ion uptake from simulated medium active waste mixture by N-hydroxy ethyl amide derivative was found to follow the following order: Fe> U> Ni> Zr> Zn> Cr. On the other hand, the measured metal uptake by hydroxamic acid derivative was found to follow: Fe>U> Zr> Ca. It is concluded that the prepared grafted copolymers are of interest for metal chelation and could be applied in the field of waste treatment

Modelling and optimization of the sound absorption of wood-wool cement boards

NARCIS (Netherlands)

Botterman, B.; Doudart de la Grée, G.C.H.; Hornikx, M.C.J.; Yu, Q.; Brouwers, H.J.H.

2018-01-01

The present article aims to characterize and improve the sound absorption of wood-wool cement boards (WWCB) with varying strand widths, densities, thicknesses and applied with varying air cavity thicknesses by using impedance models. Different rigid-frame impedance models were analysed to predict