Dangers of bypassing thermal overload relays in nuclear power plant motor operated valve circuits

International Nuclear Information System (INIS)

Baxter, F.D.

1980-01-01

Operation of motor operated valves is analyzed under various abnormal conditions such as frozen bearing, tight packing, mid-travel obstruction, torque switch failure, limit switch failure, and post-accident operation. Each condition has been reviewed to show that an adverse situation results if the thermal overload relays in the circuit are bypassed. In conclusion, there appears to be no technical basis for bypassing or oversizing the thermal overload relay provided it is selected correctly

Multistability and hidden attractors in a relay system with hysteresis

DEFF Research Database (Denmark)

Zhusubaliyev, Zhanybai T.; Mosekilde, Erik; Rubanov, Vasily G.

2015-01-01

with the neighborhood of that cycle. We show how the equilibrium point of a relay system disappears in a boundary-equilibrium bifurcation as the system enters the region of autonomous switching dynamics and demonstrate experimentally how a relay system can exhibit large amplitude chaotic oscillations at high values...... of the supply voltage. By investigating a four-dimensional model of the experimental relay system we finally show how a variety of hidden periodic, quasiperiodic and chaotic attractors arise, transform and disappear through different bifurcations. (C) 2015 Elsevier B.V. All rights reserved....

Two-Way Multi-Antenna Relaying with Simultaneous Wireless Information and Power Transfer

Directory of Open Access Journals (Sweden)

Thanaphat Srivantana

2017-03-01

Full Text Available In this paper, we propose various kinds of two-way multi-antenna relaying with simultaneous wireless information and power transfer (SWIPT and investigate their performance. Specifically, we first consider a two-way relay network where two single-antenna end nodes communicate with each other through a multi-antenna relay node that is energy constrained. This relay node harvests energy from the two end nodes and use the harvested energy for forwarding their information. Six relaying schemes that support the considered network then build on the power splitting-based relaying and time switching-based relaying protocols. The average bit error rates of these schemes are evaluated and compared by computer simulations considering several network parameters, including the number of relay antennas, power splitting ratio, and energy harvesting time. Such evaluation and comparison provide useful insights into the performance of SWIPT-based two-way multi-antenna relaying.

Wireless Powered Relaying Networks Under Imperfect Channel State Information: System Performance and Optimal Policy for Instantaneous Rate

Directory of Open Access Journals (Sweden)

D. T. Do

2017-09-01

Full Text Available In this investigation, we consider wireless powered relaying systems, where energy is scavenged by a relay via radio frequency (RF signals. We explore hybrid time switching-based and power splitting-based relaying protocol (HTPSR and compare performance of Amplify-and-Forward (AF with Decode-and-Forward (DF scheme under imperfect channel state information (CSI. Most importantly, the instantaneous rate, achievable bit error rate (BER are determined in the closed-form expressions under the impact of imperfect CSI. Through numerical analysis, we evaluate system insights via different parameters such as power splitting (PS and time switching (TS ratio of the considered HTPSR which affect outage performance and BER. It is noted that DF relaying networks outperform AF relaying networks. Besides that, the numerical results are given to prove the optimization problems of PS and TS ratio to obtain optimal instantaneous rate.

Characterization of an antagonistic switch between histone H3 lysine 27 methylation and acetylation in the transcriptional regulation of Polycomb group target genes

DEFF Research Database (Denmark)

Pasini, Diego; Malatesta, Martina; Jung, Hye Ryung

2010-01-01

Polycomb group (PcG) proteins are transcriptional repressors, which regulate proliferation and cell fate decisions during development, and their deregulated expression is a frequent event in human tumours. The Polycomb repressive complex 2 (PRC2) catalyzes trimethylation (me3) of histone H3 lysine...... are poorly understood. To gain insight into these mechanisms, we have determined the global changes in histone modifications in embryonic stem (ES) cells lacking the PcG protein Suz12 that is essential for PRC2 activity. We show that loss of PRC2 activity results in a global increase in H3K27 acetylation....... The methylation to acetylation switch correlates with the transcriptional activation of PcG target genes, both during ES cell differentiation and in MLL-AF9-transduced hematopoietic stem cells. Moreover, we provide evidence that the acetylation of H3K27 is catalyzed by the acetyltransferases p300 and CBP. Based...

An Optimal Analysis in Wireless Powered Full-duplex Relaying Network

Directory of Open Access Journals (Sweden)

K.-T. Nguyen

2017-04-01

Full Text Available Wireless-powered cellular networks (WPCNs are currently being investigated to exploit the reliability and improve battery lifetime of mobile users. This paper investigates the energy harvesting structure of the full-duplex relaying networks. By using the time switching based relaying (TSR protocol and Amplify-and-Forward (AF model in delay-limited transmission scheme, we propose the closed-form expression of the outage probability and then calculate the optimal throughput. An important result can be taken obviously that the time fraction in TSR, the position of relay, the noise as well as the energy conversation impacting on the outage probability as well as the optimal throughput. By Monte Carlo simulation, the numerical results indicate an effective relaying strategy in full-duplex cooperative systems. Finally, we provide fundamental design guidelines for selecting time fraction in TSR that satisfies the requirements of a practical relaying system.

Sum-Rate Enhancement in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma

2016-09-20

In this paper, we consider a multiuser multipleinput multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting (EH) relays and multiple destinations. All the nodes are equipped with multiple antennas. The EH and information decoding (ID) tasks at the relays and destinations are separated over the time, which is termed as the time switching (TS) scheme. As optimal solutions for the sum-rate maximization problems of BC channels and the MIMO interference channels are hard to obtain, the end-to-end sum rate maximization problem of a multiuser MIMO DF relay BC channel is even harder. In this paper, we propose to tackle a simplified problem where we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relaydestination channels using an algorithm similar to the BD method. In order to show the relevance of our low complex proposed solution, we compare it to the minimum mean-square error (MMSE) solution that was shown in the literature to be equivalent to the solution of the sum-rate maximization in MIMO broadcasting interfering channels. We also investigate the time division multiple access (TDMA) solution which separates all the information transmissions from the source to the relays and from the relays to the destinations over time. We provide numerical results to show the relevance of our proposed solution, in comparison with the no co-channel interference (CCI) case, the TDMA based solution and the MMSE based solution.

Sum-Rate Enhancement in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma; Salem, Ahmed Sultan; Alouini, Mohamed-Slim

2016-01-01

In this paper, we consider a multiuser multipleinput multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting (EH) relays and multiple destinations. All the nodes are equipped with multiple antennas. The EH and information decoding (ID) tasks at the relays and destinations are separated over the time, which is termed as the time switching (TS) scheme. As optimal solutions for the sum-rate maximization problems of BC channels and the MIMO interference channels are hard to obtain, the end-to-end sum rate maximization problem of a multiuser MIMO DF relay BC channel is even harder. In this paper, we propose to tackle a simplified problem where we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relaydestination channels using an algorithm similar to the BD method. In order to show the relevance of our low complex proposed solution, we compare it to the minimum mean-square error (MMSE) solution that was shown in the literature to be equivalent to the solution of the sum-rate maximization in MIMO broadcasting interfering channels. We also investigate the time division multiple access (TDMA) solution which separates all the information transmissions from the source to the relays and from the relays to the destinations over time. We provide numerical results to show the relevance of our proposed solution, in comparison with the no co-channel interference (CCI) case, the TDMA based solution and the MMSE based solution.

Protective relay

International Nuclear Information System (INIS)

Lim, Mu Ji; Jung, Hae Sang

1974-10-01

This book is divided into two chapters, which deals with protective relay. The first chapter deals with the basic knowledge of relay on development of relay, classification of protective relay, rating of protective relay general structure of protective relay, detecting of ground protection, about point of contact, operating relay and trip relaying. The second chapter is about structure and explanation of relay on classification by structure such as motor type and moving-coil type, explanation of other relays over current relay, over voltage relay, short voltage relay, relay for power, relay for direction, test of over voltage relay, test of short voltage relay and test of directional circuit relay.

Near optimal power allocation algorithm for OFDM-based cognitive using adaptive relaying strategy

KAUST Repository

Soury, Hamza; Bader, Faouzi; Shaat, Musbah M R; Alouini, Mohamed-Slim

2012-01-01

Relayed transmission increases the coverage and achievable capacity of communication systems. Adaptive relaying scheme is a relaying technique by which the benefits of the amplifying or decode and forward techniques can be achieved by switching the forwarding technique according to the quality of the signal. A cognitive Orthogonal Frequency-Division Multiplexing (OFDM) based adaptive relaying protocol is considered in this paper. The objective is to maximize the capacity of the cognitive radio system while ensuring that the interference introduced to the primary user is below the tolerated limit. A Near optimal power allocation in the source and the relay is presented for two pairing techniques such that the matching and random pairing. The simulation results confirm the efficiency of the proposed adaptive relaying protocol, and the consequence of choice of pairing technique. © 2012 ICST.

Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

KAUST Repository

Benkhelifa, Fatma; Alouini, Mohamed-Slim

2016-01-01

In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) for the two-hop Multiple-Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with the multiantenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the sourcedestination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) which separate the EH and ID transfer over the power domain and the time domain, respectively.

Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

KAUST Repository

Benkhelifa, Fatma

2016-01-06

In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) for the two-hop Multiple-Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with the multiantenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the sourcedestination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) which separate the EH and ID transfer over the power domain and the time domain, respectively.

Simultaneous Wireless Information and Power Transfer Mechanism in Interference Alignment Relay Networks

Directory of Open Access Journals (Sweden)

Fahui Wu

2016-01-01

Full Text Available This paper considers a simultaneous wireless information and power transfer (SWIPT mechanism in an interference alignment (IA relay system, in which source nodes send wireless information and energy simultaneously to relay nodes, and relay nodes forward the received signal to destination nodes powered by harvested energy. To manage interference and utilize interference as energy source, two-SWIPT receiver is designed, namely, power splitting (PS, and antennas switching (AS has been considered for relay system. The performance of AS- and PS-based IA relay systems is considered, as is a new energy cooperation (ECop scheme that is proposed to improve system performance. Numerical results are provided to evaluate the performance of all schemes and it is shown from the simulations that the performance of proposed ECop outperformed both AS and PS.

Semiconductor relay and its manufacture method. Handotai relay oyobi sono seizo hoho

Energy Technology Data Exchange (ETDEWEB)

Nakamura, M

1993-06-01

The invention relates to a semiconductor relay in which a light emitting diode and a photovoltaic element are arranged in the opposite positions and connected with a light connection and aims to present a light transmission path to transmit input signals to the light emitting diode to the side of the photovoltaic element with a negligible light loss effectively. The invention presents a semiconductor relay, in which a light emitting diode loaded on the first lead frame and the light receiving part of the photovoltaic element to drive a MOSFET element loaded on the second lead frame and acting as a switch element are connected through an insulator tube with an opaque outer wall, and the interior of the insulator tube is filled with a transparent insulating filler, so that the invention affords a light transmission path without light leakage from the interior of the opaque insulator tube and with the stability in the form and no light loss. 3 figs.

Nanoelectromechanical Switches for Low-Power Digital Computing

Directory of Open Access Journals (Sweden)

Alexis Peschot

2015-08-01

Full Text Available The need for more energy-efficient solid-state switches beyond complementary metal-oxide-semiconductor (CMOS transistors has become a major concern as the power consumption of electronic integrated circuits (ICs steadily increases with technology scaling. Nano-Electro-Mechanical (NEM relays control current flow by nanometer-scale motion to make or break physical contact between electrodes, and offer advantages over transistors for low-power digital logic applications: virtually zero leakage current for negligible static power consumption; the ability to operate with very small voltage signals for low dynamic power consumption; and robustness against harsh environments such as extreme temperatures. Therefore, NEM logic switches (relays have been investigated by several research groups during the past decade. Circuit simulations calibrated to experimental data indicate that scaled relay technology can overcome the energy-efficiency limit of CMOS technology. This paper reviews recent progress toward this goal, providing an overview of the different relay designs and experimental results achieved by various research groups, as well as of relay-based IC design principles. Remaining challenges for realizing the promise of nano-mechanical computing, and ongoing efforts to address these, are discussed.

Self-oscillations in dynamic systems a new methodology via two-relay controllers

CERN Document Server

Aguilar, Luis T; Fridman, Leonid; Iriarte, Rafael

2015-01-01

This monograph presents a simple and efficient two-relay control algorithm for generation of self-excited oscillations of a desired amplitude and frequency in dynamic systems. Developed by the authors, the two-relay controller consists of two relays switched by the feedback received from a linear or nonlinear system, and represents a new approach to the self-generation of periodic motions in underactuated mechanical systems. The first part of the book explains the design procedures for two-relay control using three different methodologies – the describing-function method, Poincaré maps, and the locus-of-a perturbed-relay-system method – and concludes with stability analysis of designed periodic oscillations. Two methods to ensure the robustness of two-relay control algorithms are explored in the second part, one based on the combination of the high-order sliding mode controller and backstepping, and the other on higher-order sliding-modes-based reconstruction of uncertainties and their compensation where...

p53 Acetylation: Regulation and Consequences

International Nuclear Information System (INIS)

Reed, Sara M.; Quelle, Dawn E.

2014-01-01

Post-translational modifications of p53 are critical in modulating its tumor suppressive functions. Ubiquitylation, for example, plays a major role in dictating p53 stability, subcellular localization and transcriptional vs. non-transcriptional activities. Less is known about p53 acetylation. It has been shown to govern p53 transcriptional activity, selection of growth inhibitory vs. apoptotic gene targets, and biological outcomes in response to diverse cellular insults. Yet recent in vivo evidence from mouse models questions the importance of p53 acetylation (at least at certain sites) as well as canonical p53 functions (cell cycle arrest, senescence and apoptosis) to tumor suppression. This review discusses the cumulative findings regarding p53 acetylation, with a focus on the acetyltransferases that modify p53 and the mechanisms regulating their activity. We also evaluate what is known regarding the influence of other post-translational modifications of p53 on its acetylation, and conclude with the current outlook on how p53 acetylation affects tumor suppression. Due to redundancies in p53 control and growing understanding that individual modifications largely fine-tune p53 activity rather than switch it on or off, many questions still remain about the physiological importance of p53 acetylation to its role in preventing cancer

p53 Acetylation: Regulation and Consequences

Energy Technology Data Exchange (ETDEWEB)

Reed, Sara M. [Department of Pharmacology, The University of Iowa Carver College of Medicine, Iowa City, IA 52242 (United States); Medical Scientist Training Program, The University of Iowa Carver College of Medicine, Iowa City, IA 52242 (United States); Quelle, Dawn E., E-mail: dawn-quelle@uiowa.edu [Department of Pharmacology, The University of Iowa Carver College of Medicine, Iowa City, IA 52242 (United States); Medical Scientist Training Program, The University of Iowa Carver College of Medicine, Iowa City, IA 52242 (United States); Department of Pathology, The University of Iowa Carver College of Medicine, Iowa City, IA 52242 (United States)

2014-12-23

Post-translational modifications of p53 are critical in modulating its tumor suppressive functions. Ubiquitylation, for example, plays a major role in dictating p53 stability, subcellular localization and transcriptional vs. non-transcriptional activities. Less is known about p53 acetylation. It has been shown to govern p53 transcriptional activity, selection of growth inhibitory vs. apoptotic gene targets, and biological outcomes in response to diverse cellular insults. Yet recent in vivo evidence from mouse models questions the importance of p53 acetylation (at least at certain sites) as well as canonical p53 functions (cell cycle arrest, senescence and apoptosis) to tumor suppression. This review discusses the cumulative findings regarding p53 acetylation, with a focus on the acetyltransferases that modify p53 and the mechanisms regulating their activity. We also evaluate what is known regarding the influence of other post-translational modifications of p53 on its acetylation, and conclude with the current outlook on how p53 acetylation affects tumor suppression. Due to redundancies in p53 control and growing understanding that individual modifications largely fine-tune p53 activity rather than switch it on or off, many questions still remain about the physiological importance of p53 acetylation to its role in preventing cancer.

High-voltage switching for in-flight capture of keV antiprotons in a Penning trap

International Nuclear Information System (INIS)

Fei, X.; Davisson, R.; Gabrielse, G.

1987-01-01

The recently observed in-flight capture of keV antiprotons and protons in a Penning trap requires that the -3-kV potentials on electrodes of a Penning trap near 4.2 K be switched on and off with switching times less than 20 ns. These rapidly switched potentials are applied via transmission lines which are not terminated at the trap, thereby avoiding unacceptable heat load on the helium Dewar. Simple high-voltage switching circuits are constructed using krytrons and reed relays. A krytron provides the rapid switching and stays on just long enough for a reed relay to kick in and maintain the switched state indefinitely

Opportunistic relaying in multipath and slow fading channel: Relay selection and optimal relay selection period

KAUST Repository

Sungjoon Park,

2011-11-01

In this paper we present opportunistic relay communication strategies of decode and forward relaying. The channel that we are considering includes pathloss, shadowing, and fast fading effects. We find a simple outage probability formula for opportunistic relaying in the channel, and validate the results by comparing it with the exact outage probability. Also, we suggest a new relay selection algorithm that incorporates shadowing. We consider a protocol of broadcasting the channel gain of the previously selected relay. This saves resources in slow fading channel by reducing collisions in relay selection. We further investigate the optimal relay selection period to maximize the throughput while avoiding selection overhead. © 2011 IEEE.

Wireless Power Transfer in Cooperative DF Relaying Networks with Log-Normal Fading

KAUST Repository

Rabie, Khaled M.; Adebisi, Bamidele; Alouini, Mohamed-Slim

2017-01-01

Energy-harvesting (EH) and wireless power transfer in cooperative relaying networks have recently attracted a considerable amount of research attention. Most of the existing work on this topic however focuses on Rayleigh fading channels which represents outdoor environments. Unlike these studies, in this paper we analyze the performance of wireless power transfer in two-hop decode-and- forward (DF) cooperative relaying systems in indoor channels characterized by log-normal fading. Three well-known EH protocols are considered in our evaluations: a) time switching relaying (TSR), b) power splitting relaying (PSR) and c) ideal relaying receiver (IRR). The performance is evaluated in terms of the ergodic outage probability for which we derive accurate analytical expressions for the three systems under consideration. Results reveal that careful selection of the EH time and power splitting factors in the TSR- and PSR-based system are important to optimize performance. It is also presented that the optimized PSR system has near- ideal performance and that increasing the source transmit power and/or the energy harvester efficiency can further improve performance.

Wireless Power Transfer in Cooperative DF Relaying Networks with Log-Normal Fading

KAUST Repository

Rabie, Khaled M.

2017-02-07

Energy-harvesting (EH) and wireless power transfer in cooperative relaying networks have recently attracted a considerable amount of research attention. Most of the existing work on this topic however focuses on Rayleigh fading channels which represents outdoor environments. Unlike these studies, in this paper we analyze the performance of wireless power transfer in two-hop decode-and- forward (DF) cooperative relaying systems in indoor channels characterized by log-normal fading. Three well-known EH protocols are considered in our evaluations: a) time switching relaying (TSR), b) power splitting relaying (PSR) and c) ideal relaying receiver (IRR). The performance is evaluated in terms of the ergodic outage probability for which we derive accurate analytical expressions for the three systems under consideration. Results reveal that careful selection of the EH time and power splitting factors in the TSR- and PSR-based system are important to optimize performance. It is also presented that the optimized PSR system has near- ideal performance and that increasing the source transmit power and/or the energy harvester efficiency can further improve performance.

An experimental mechanical switch for 3 kA driven by superconducting coils

International Nuclear Information System (INIS)

Herman, H.J.; Ten Haken, B.; Van de Klundert, L.J.M.

1986-01-01

Usually mechanical switches that are built for use in superconducting circuits are driven in some way by a rod which is controlled at room temperature. In this paper, an alternative method to drive the electrodes of the switch is reported. In fact the new device is a superconducting relay that uses an antiseries connection of two superconducting air-core coils. The repulsing force of these relay coils enables the switch to be closed by applying a pressure to the electrodes. The off-state is effected by a set of springs which interrupt the electrodes when the coil current is switched off. We realized that this electro-magnetic method of producing large forces could be promising for driving a mechanical switch. The desired method was demonstrated by an experimental model. A switch-on resistance of 8*10 -8 Ω with a switch current of 3 kA and a contact force of 20 kN was measured

Energy-harvesting in cooperative AF relaying networks over log-normal fading channels

KAUST Repository

Rabie, Khaled M.; Salem, Abdelhamid; Alsusa, Emad; Alouini, Mohamed-Slim

2016-01-01

Energy-harvesting (EH) and wireless power transfer are increasingly becoming a promising source of power in future wireless networks and have recently attracted a considerable amount of research, particularly on cooperative two-hop relay networks in Rayleigh fading channels. In contrast, this paper investigates the performance of wireless power transfer based two-hop cooperative relaying systems in indoor channels characterized by log-normal fading. Specifically, two EH protocols are considered here, namely, time switching relaying (TSR) and power splitting relaying (PSR). Our findings include accurate analytical expressions for the ergodic capacity and ergodic outage probability for the two aforementioned protocols. Monte Carlo simulations are used throughout to confirm the accuracy of our analysis. The results show that increasing the channel variance will always provide better ergodic capacity performance. It is also shown that a good selection of the EH time in the TSR protocol, and the power splitting factor in the PTS protocol, is the key to achieve the best system performance. © 2016 IEEE.

Energy-harvesting in cooperative AF relaying networks over log-normal fading channels

KAUST Repository

Rabie, Khaled M.

2016-07-26

Energy-harvesting (EH) and wireless power transfer are increasingly becoming a promising source of power in future wireless networks and have recently attracted a considerable amount of research, particularly on cooperative two-hop relay networks in Rayleigh fading channels. In contrast, this paper investigates the performance of wireless power transfer based two-hop cooperative relaying systems in indoor channels characterized by log-normal fading. Specifically, two EH protocols are considered here, namely, time switching relaying (TSR) and power splitting relaying (PSR). Our findings include accurate analytical expressions for the ergodic capacity and ergodic outage probability for the two aforementioned protocols. Monte Carlo simulations are used throughout to confirm the accuracy of our analysis. The results show that increasing the channel variance will always provide better ergodic capacity performance. It is also shown that a good selection of the EH time in the TSR protocol, and the power splitting factor in the PTS protocol, is the key to achieve the best system performance. © 2016 IEEE.

Relay tracking control for second-order multi-agent systems with damaged agents.

Science.gov (United States)

Dong, Lijing; Li, Jing; Liu, Qin

2017-11-01

This paper investigates a situation where smart agents capable of sensory and mobility are deployed to monitor a designated area. A preset number of agents start tracking when a target intrudes this area. Some of the tracking agents are possible to be out of order over the tracking course. Thus, we propose a cooperative relay tracking strategy to ensure the successful tracking with existence of damaged agents. Relay means that, when a tracking agent quits tracking due to malfunction, one of the near deployed agents replaces it to continue the tracking task. This results in jump of tracking errors and dynamic switching of topology of the multi-agent system. Switched system technique is employed to solve this specific problem. Finally, the effectiveness of proposed tracking strategy and validity of the theoretical results are verified by conducting a numerical simulation. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Simultaneous energy harvesting and information processing in wireless multiple relays with multiple antennas

Science.gov (United States)

Albaaj, Azhar; Makki, S. Vahab A.; Alabkhat, Qassem; Zahedi, Abdulhamid

2017-07-01

Wireless networks suffer from battery discharging specially in cooperative communications when multiple relays have an important role but they are energy constrained. To overcome this problem, energy harvesting from radio frequency signals is applied to charge the node battery. These intermediate nodes have the ability to harvest energy from the source signal and use the energy harvested to transmit information to the destination. In fact, the node tries to harvest energy and then transmit the data to destination. Division of energy harvesting and data transmission can be done in two algorithms: time-switching-based relaying protocol and power-splitting-based relaying protocol. These two algorithms also can be applied in delay-limited and delay-tolerant transmission systems. The previous works have assumed a single relay for energy harvesting, but in this article, the proposed method is concentrated on improving the outage probability and throughput by using multiple antennas in each relay node instead of using single antenna. According to our simulation results, when using multi-antenna relays, ability of energy harvesting is increased and thus system performance will be improved to great extent. Maximum ratio combining scheme has been used when the destination chooses the best signal of relays and antennas satisfying the required signal-to-noise ratio.

Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

KAUST Repository

Benkhelifa, Fatma

2016-03-28

© 2015 IEEE. In this paper, we investigate two-hop Multiple- Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with simultaneous wireless information and power transfer (SWIPT) at the multi-antenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the source-destination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. This scheme provides an outer bound for the achievable R-E region since practical energy harvesting circuits are not yet able to harvest the energy and decode the information simultaneously. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) proposed in [1] and which separate the EH and ID transfer over the power domain and the time domain, respectively. In our study, we derive the boundary of the achievable R- E region and we show the effect of the source transmit power, the relay transmit power and the position of the relay between the source and the destination on the achievable R-E region for the ideal scenario and the two practical schemes.

Half-Duplex and Full-Duplex AF and DF Relaying with Energy-Harvesting in Log-Normal Fading

KAUST Repository

Rabie, Khaled M.

2017-08-15

Energy-harvesting (EH) and wireless power transfer in cooperative relaying networks have recently attracted a considerable amount of research attention. Most of the existing work on this topic however focuses on Rayleigh fading channels, which represent outdoor environments. In contrast, this paper is dedicated to analyze the performance of dual-hop relaying systems with EH over indoor channels characterized by log-normal fading. Both half-duplex (HD) and full-duplex (FD) relaying mechanisms are studied in this work with decode-and-forward (DF) and amplify-and-forward (AF) relaying protocols. In addition, three EH schemes are investigated, namely, time switching relaying, power splitting relaying and ideal relaying receiver which serves as a lower bound. The system performance is evaluated in terms of the ergodic outage probability for which we derive accurate analytical expressions. Monte Carlo simulations are provided throughout to validate the accuracy of our analysis. Results reveal that, in both HD and FD scenarios, AF relaying performs only slightly worse than DF relaying which can make the former a more efficient solution when the processing energy cost at the DF relay is taken into account. It is also shown that FD relaying systems can generally outperform HD relaying schemes as long as the loop-back interference in FD is relatively small. Furthermore, increasing the variance of the log-normal channel has shown to deteriorate the performance in all the relaying and EH protocols considered.

Alternate transmission with half-duplex relaying in MIMO interference relay networks

KAUST Repository

Park, Seongho

2013-12-01

In this paper, we consider an alternate transmission scheme for a multiple-input multiple-output interference relay channel where multiple sources transmit their own signals to their corresponding destinations via one of two relaying groups alternately every time phase. Each of the relaying groups has arbitrary number of relays, and each relay operates in half-duplex amplify-and-forward mode. In our scheme, the received signals at the relay nodes consist of desired signals and two different interference signals such as the inter-source interferences and the inter-group interferences which are caused by the phase incoherence of relaying. As such, we propose an iterative interference alignment algorithm to mitigate the interferences. We show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying system in the interference relay channels. © 2013 IEEE.

Alternate MIMO relaying with three AF relays using interference alignment

KAUST Repository

Park, Kihong

2012-06-01

In this paper, we study a two-hop half-duplex relaying network with one source, one destination, and three amplify-and-forward (AF) relays equipped with M antennas each. We consider alternate transmission to compensate for the inherent loss of capacity pre-log factor 1/2 in half duplex mode, where source transmit message to two relays and the other relay alternately. The inter-relay interference caused by alternate transmission is aligned to make additional degrees of freedom (DOFs). It is shown that the proposed scheme enables us to exploit 3M/4 DOFs compared with the M/2 DOFs of conventional AF relaying. More specifically, suboptimal linear filter designs for a source and three relays are proposed to maximize the achievable sum-rate. We verify using some selected numerical results that the proposed filter designs give significant improvement of the sum-rate over a naive filter and conventional relaying schemes. © 2012 IEEE.

Relay race

CERN Multimedia

Staff Association

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19th May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the course, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay Some advice for all runners from the medical service can also be found here: https://espace.cern.ch/Running-Club/CERN-Relay/RelayPagePictures/MedicalServiceAnnoncement.pdf

Relay race

CERN Document Server

Staff Association

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19th May starting at 12·15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the course, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay Some advice for all runners from the medical service can also be found here: https://espace.cern.ch/Running-Club/CERN-Relay/RelayPagePictures/MedicalServiceAnnoncement.pdf

Outage Analysis and Optimization of SWIPT in Network-Coded Two-Way Relay Networks

Directory of Open Access Journals (Sweden)

Ruihong Jiang

2017-01-01

Full Text Available This paper investigates the outage performance of simultaneous wireless information and power transfer (SWIPT in network-coded two-way relay systems, where a relay first harvests energy from the signals transmitted by two sources and then uses the harvested energy to forward the received information to the two sources. We consider two transmission protocols, power splitting two-way relay (PS-TWR and time switching two-way relay (TS-TWR protocols. We present two explicit expressions for the system outage probability of the two protocols and further derive approximate expressions for them in high and low SNR cases. To explore the system performance limits, two optimization problems are formulated to minimize the system outage probability. Since the problems are nonconvex and have no known solution methods, a genetic algorithm- (GA- based algorithm is designed. Numerical and simulation results validate our theoretical analysis. It is shown that, by jointly optimizing the time assignment and SWIPT receiver parameters, a great performance gain can be achieved for both PS-TWR and TS-TWR. Moreover, the optimized PS-TWR always outperforms the optimized TS-TWR in terms of outage performance. Additionally, the effects of parameters including relay location and transmit powers are also discussed, which provide some insights for the SWIPT-enabled two-way relay networks.

Reactive relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz

2012-06-01

Best relay selection is a bandwidth efficient technique for multiple relay environments without compromising the system performance. The problem of relay selection is more challenging in underlay cognitive networks due to strict interference constraints to the primary users. Generally, relay selection is done on the basis of maximum end-to-end signal to noise ratio (SNR). However, it requires large amounts of channel state information (CSI) at different network nodes. In this paper, we present and analyze a reactive relay selection scheme in underlay cognitive networks where the relays are operating with fixed gains near a primary user. The system model minimizes the amount of CSI required at different nodes and the destination selects the best relay on the basis of maximum relay to destination SNR. We derive close form expressions for the received SNR statistics, outage probability, bit error probability and average channel capacity of the system. Simulation results are also presented to confirm the validity of the derived expressions. © 2012 IEEE.

Partial relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz; Alouini, Mohamed-Slim; Hasna, Mazen Omar; Qaraqe, Khalid A.

2012-01-01

In a communication system with multiple cooperative relays, selecting the best relay utilizes the available spectrum more efficiently. However, selective relaying poses a different problem in underlay cognitive networks compared to the traditional cooperative networks due to interference thresholds to the primary users. In most cases, a best relay is the one which provides the maximum end-to-end signal to noise ratio (SNR). This approach needs plenty of instantaneous channel state information (CSI). The CSI burden could be reduced by partial relay selection. In this paper, a partial relay selection scheme is presented and analyzed for an underlay cognitive network with fixed gain relays operating in the vicinity of a primary user. The system model is adopted in a way that each node needs minimal CSI to perform its task. The best relay is chosen on the basis of maximum source to relay link SNR which then forwards the message to the destination. We derive closed form expressions for the received SNR distributions, system outage, probability of bit error and average channel capacity of the system. The derived results are confirmed through simulations. © 2012 IEEE.

Partial relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz

2012-05-01

In a communication system with multiple cooperative relays, selecting the best relay utilizes the available spectrum more efficiently. However, selective relaying poses a different problem in underlay cognitive networks compared to the traditional cooperative networks due to interference thresholds to the primary users. In most cases, a best relay is the one which provides the maximum end-to-end signal to noise ratio (SNR). This approach needs plenty of instantaneous channel state information (CSI). The CSI burden could be reduced by partial relay selection. In this paper, a partial relay selection scheme is presented and analyzed for an underlay cognitive network with fixed gain relays operating in the vicinity of a primary user. The system model is adopted in a way that each node needs minimal CSI to perform its task. The best relay is chosen on the basis of maximum source to relay link SNR which then forwards the message to the destination. We derive closed form expressions for the received SNR distributions, system outage, probability of bit error and average channel capacity of the system. The derived results are confirmed through simulations. © 2012 IEEE.

Opportunistic Relay Selection in Multicast Relay Networks using Compressive Sensing

KAUST Repository

Elkhalil, Khalil

2014-12-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. However, for relay selection algorithms to make a selection decision, channel state information (CSI) from all cooperating relays is usually required at a central node. This requirement poses two important challenges. Firstly, CSI acquisition generates a great deal of feedback overhead (air-time) that could result in significant transmission delays. Secondly, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we introduce a limited feedback relay selection algorithm for a multicast relay network. The proposed algorithm exploits the theory of compressive sensing to first obtain the identity of the “strong” relays with limited feedback. Following that, the CSI of the selected relays is estimated using linear minimum mean square error estimation. To minimize the effect of noise on the fed back CSI, we introduce a back-off strategy that optimally backs-off on the noisy estimated CSI. For a fixed group size, we provide closed form expressions for the scaling law of the maximum equivalent SNR for both Decode and Forward (DF) and Amplify and Forward (AF) cases. Numerical results show that the proposed algorithm drastically reduces the feedback air-time and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback channels.

Joint Subcarrier Pairing and Resource Allocation for Cognitive Network and Adaptive Relaying Strategy

KAUST Repository

Soury, Hamza

2012-05-01

Recent measurements show that the spectrum is under-utilized by licensed users in wireless communication. Cognitive radio (CR) has been proposed as a suitable solution to manage the inefficient usage of the spectrum and increase coverage area of wireless networks. The concept is based on allowing a group of secondary users (SUs) to share the unused radio spectrum originally owned by the primary user (PUs). The operation of CR should not cause harmful interference to the PUs. In the other hand, relayed transmission increases the coverage and achievable capacity of communication systems and in particular in CR systems. In fact there are many types of cooperative communications, however the two main ones are decode-and-forward (DAF) and amplify-and-forward (AAF). Adaptive relaying scheme is a relaying technique by which the benefits of the amplifying or decode and forward techniques can be achieved by switching the forwarding technique according to the quality of the signal. In this dissertation, we investigate the power allocation for an adaptive relaying protocol (ARP) scheme in cognitive system by maximizing the end-to-end rate and searching the best carriers pairing distribution. The optimization problem is under the interference and power budget constraints. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques, and the consequence of the choice of the pairing strategy.

Proteomic Analysis of Lysine Acetylation Sites in Rat Tissues Reveals Organ Specificity and Subcellular Patterns

Directory of Open Access Journals (Sweden)

Alicia Lundby

2012-08-01

Full Text Available Lysine acetylation is a major posttranslational modification involved in a broad array of physiological functions. Here, we provide an organ-wide map of lysine acetylation sites from 16 rat tissues analyzed by high-resolution tandem mass spectrometry. We quantify 15,474 modification sites on 4,541 proteins and provide the data set as a web-based database. We demonstrate that lysine acetylation displays site-specific sequence motifs that diverge between cellular compartments, with a significant fraction of nuclear sites conforming to the consensus motifs G-AcK and AcK-P. Our data set reveals that the subcellular acetylation distribution is tissue-type dependent and that acetylation targets tissue-specific pathways involved in fundamental physiological processes. We compare lysine acetylation patterns for rat as well as human skeletal muscle biopsies and demonstrate its general involvement in muscle contraction. Furthermore, we illustrate that acetylation of fructose-bisphosphate aldolase and glycerol-3-phosphate dehydrogenase serves as a cellular mechanism to switch off enzymatic activity.

Optimized Power Allocation and Relay Location Selection in Cooperative Relay Networks

Directory of Open Access Journals (Sweden)

Jianrong Bao

2017-01-01

Full Text Available An incremental selection hybrid decode-amplify forward (ISHDAF scheme for the two-hop single relay systems and a relay selection strategy based on the hybrid decode-amplify-and-forward (HDAF scheme for the multirelay systems are proposed along with an optimized power allocation for the Internet of Thing (IoT. Given total power as the constraint and outage probability as an objective function, the proposed scheme possesses good power efficiency better than the equal power allocation. By the ISHDAF scheme and HDAF relay selection strategy, an optimized power allocation for both the source and relay nodes is obtained, as well as an effective reduction of outage probability. In addition, the optimal relay location for maximizing the gain of the proposed algorithm is also investigated and designed. Simulation results show that, in both single relay and multirelay selection systems, some outage probability gains by the proposed scheme can be obtained. In the comparison of the optimized power allocation scheme with the equal power allocation one, nearly 0.1695 gains are obtained in the ISHDAF single relay network at a total power of 2 dB, and about 0.083 gains are obtained in the HDAF relay selection system with 2 relays at a total power of 2 dB.

Threshold-Based Relay Selection for Detect-and-Forward Relaying in Cooperative Wireless Networks

Directory of Open Access Journals (Sweden)

Fan Yijia

2010-01-01

Full Text Available This paper studies two-hop cooperative demodulate-and-forward relaying using multiple relays in wireless networks. A threshold based relay selection scheme is considered, in which the reliable relays are determined by comparing source-relay SNR to a threshold, and one of the reliable relays is selected by the destination based on relay-destination SNR. The exact bit error rate of this scheme is derived, and a simple threshold function is proposed. It is shown that the network achieves full diversity order ( under the proposed threshold, where is the number of relays in the network. Unlike some other full diversity achieving protocols in the literature, the requirement that the instantaneous/average SNRs of the source-relay links be known at the destination is eliminated using the appropriate SNR threshold.

Telecommunications Relay Services

Science.gov (United States)

... Home » Health Info » Hearing, Ear Infections, and Deafness Telecommunications Relay Services On this page: What are telecommunication ... additional information about telecommunication relay services? What are telecommunication relay services? Title IV of the Americans with ...

Reactive relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Hasna, Mazen Omar

2012-01-01

Best relay selection is a bandwidth efficient technique for multiple relay environments without compromising the system performance. The problem of relay selection is more challenging in underlay cognitive networks due to strict interference

Individual Channel Estimation in a Diamond Relay Network Using Relay-Assisted Training

Directory of Open Access Journals (Sweden)

Xianwen He

2017-01-01

Full Text Available We consider the training design and channel estimation in the amplify-and-forward (AF diamond relay network. Our strategy is to transmit the source training in time-multiplexing (TM mode while each relay node superimposes its own relay training over the amplified received data signal without bandwidth expansion. The principal challenge is to obtain accurate channel state information (CSI of second-hop link due to the multiaccess interference (MAI and cooperative data interference (CDI. To maintain the orthogonality between data and training, a modified relay-assisted training scheme is proposed to migrate the CDI, where some of the cooperative data at the relay are discarded to accommodate relay training. Meanwhile, a couple of optimal zero-correlation zone (ZCZ relay-assisted sequences are designed to avoid MAI. At the destination node, the received signals from the two relay nodes are combined to achieve spatial diversity and enhanced data reliability. The simulation results are presented to validate the performance of the proposed schemes.

Efficient incremental relaying

KAUST Repository

Fareed, Muhammad Mehboob

2013-07-01

We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying scheme with both amplify and forward and decode and forward relaying. Numerical results are also presented to verify their analytical counterparts. © 2013 IEEE.

Distributed Antenna Channels with Regenerative Relaying: Relay Selection and Asymptotic Capacity

Directory of Open Access Journals (Sweden)

Aitor del Coso

2007-11-01

Full Text Available Multiple-input-multiple-output (MIMO techniques have been widely proposed as a means to improve capacity and reliability of wireless channels, and have become the most promising technology for next generation networks. However, their practical deployment in current wireless devices is severely affected by antenna correlation, which reduces their impact on performance. One approach to solve this limitation is relaying diversity. In relay channels, a set of N wireless nodes aids a source-destination communication by relaying the source data, thus creating a distributed antenna array with uncorrelated path gains. In this paper, we study this multiple relay channel (MRC following a decode-and-forward (D&F strategy (i.e., regenerative forwarding, and derive its achievable rate under AWGN. A half-duplex constraint on relays is assumed, as well as distributed channel knowledge at both transmitter and receiver sides of the communication. For this channel, we obtain the optimum relay selection algorithm and the optimum power allocation within the network so that the transmission rate is maximized. Likewise, we bound the ergodic performance of the achievable rate and derive its asymptotic behavior in the number of relays. Results show that the achievable rate of regenerative MRC grows as the logarithm of the Lambert W function of the total number of relays, that is, 𝒞=log⁡2(W0(N. Therefore, D&F relaying, cannot achieve the capacity of actual MISO channels.

A p300 and SIRT1 Regulated Acetylation Switch of C/EBPα Controls Mitochondrial Function

Directory of Open Access Journals (Sweden)

Mohamad A. Zaini

2018-01-01

Full Text Available Summary: Cellular metabolism is a tightly controlled process in which the cell adapts fluxes through metabolic pathways in response to changes in nutrient supply. Among the transcription factors that regulate gene expression and thereby cause changes in cellular metabolism is the basic leucine-zipper (bZIP transcription factor CCAAT/enhancer-binding protein alpha (C/EBPα. Protein lysine acetylation is a key post-translational modification (PTM that integrates cellular metabolic cues with other physiological processes. Here, we show that C/EBPα is acetylated by the lysine acetyl transferase (KAT p300 and deacetylated by the lysine deacetylase (KDAC sirtuin1 (SIRT1. SIRT1 is activated in times of energy demand by high levels of nicotinamide adenine dinucleotide (NAD+ and controls mitochondrial biogenesis and function. A hypoacetylated mutant of C/EBPα induces the transcription of mitochondrial genes and results in increased mitochondrial respiration. Our study identifies C/EBPα as a key mediator of SIRT1-controlled adaption of energy homeostasis to changes in nutrient supply. : Zaini et al. show that the transcription factor C/EBPα is acetylated by p300 and deacetylated by the lysine deacetylase SIRT1. Hypoacetylated C/EBPα induces the transcription of mitochondrial genes and results in increased mitochondrial respiration. C/EBPα is a key mediator of SIRT1-controlled adaption of energy homeostasis to changes in nutrient supply. Keywords: C/EBPα, SIRT1, p300, lysine acetylation, mitochondrial function, cellular metabolism, NAD+, gene regulation

Opportunistic relaying in multipath and slow fading channel: Relay selection and optimal relay selection period

KAUST Repository

Sungjoon Park,; Stark, Wayne E.

2011-01-01

In this paper we present opportunistic relay communication strategies of decode and forward relaying. The channel that we are considering includes pathloss, shadowing, and fast fading effects. We find a simple outage probability formula

Relay Selection for Cooperative Relaying in Wireless Energy Harvesting Networks

Science.gov (United States)

Zhu, Kaiyan; Wang, Fei; Li, Songsong; Jiang, Fengjiao; Cao, Lijie

2018-01-01

Energy harvesting from the surroundings is a promising solution to provide energy supply and extend the life of wireless sensor networks. Recently, energy harvesting has been shown as an attractive solution to prolong the operation of cooperative networks. In this paper, we propose a relay selection scheme to optimize the amplify-and-forward (AF) cooperative transmission in wireless energy harvesting cooperative networks. The harvesting energy and channel conditions are considered to select the optimal relay as cooperative relay to minimize the outage probability of the system. Simulation results show that our proposed relay selection scheme achieves better outage performance than other strategies.

Relay Selection and Resource Allocation in One-Way and Two-Way Cognitive Relay Networks

KAUST Repository

Alsharoa, Ahmad M.

2013-05-08

In this work, the problem of relay selection and resource power allocation in one- way and two-way cognitive relay networks using half duplex channels with different relaying protocols is investigated. Optimization problems for both single and multiple relay selection that maximize the sum rate of the secondary network without degrading the quality of service of the primary network by respecting a tolerated interference threshold were formulated. Single relay selection and optimal power allocation for two-way relaying cognitive radio networks using decode-and-forward and amplify-and-forward protocols were studied. Dual decomposition and subgradient methods were used to find the optimal power allocation. The transmission process to exchange two different messages between two transceivers for two-way relaying technique takes place in two time slots. In the first slot, the transceivers transmit their signals simultaneously to the relay. Then, during the second slot the relay broadcasts its signal to the terminals. Moreover, improvement of both spectral and energy efficiency can be achieved compared with the one-way relaying technique. As an extension, a multiple relay selection for both one-way and two-way relaying under cognitive radio scenario using amplify-and-forward were discussed. A strong optimization tool based on genetic and iterative algorithms was employed to solve the 
formulated optimization problems for both single and multiple relay selection, where discrete relay power levels were considered. Simulation results show that the practical and low-complexity heuristic approaches achieve almost the same performance of the optimal relay selection schemes either with discrete or continuous power distributions while providing a considerable saving in terms of computational complexity.

Joint source and relay optimization for interference MIMO relay networks

Science.gov (United States)

Khandaker, Muhammad R. A.; Wong, Kai-Kit

2017-12-01

This paper considers multiple-input multiple-output (MIMO) relay communication in multi-cellular (interference) systems in which MIMO source-destination pairs communicate simultaneously. It is assumed that due to severe attenuation and/or shadowing effects, communication links can be established only with the aid of a relay node. The aim is to minimize the maximal mean-square-error (MSE) among all the receiving nodes under constrained source and relay transmit powers. Both one- and two-way amplify-and-forward (AF) relaying mechanisms are considered. Since the exactly optimal solution for this practically appealing problem is intractable, we first propose optimizing the source, relay, and receiver matrices in an alternating fashion. Then we contrive a simplified semidefinite programming (SDP) solution based on the error covariance matrix decomposition technique, avoiding the high complexity of the iterative process. Numerical results reveal the effectiveness of the proposed schemes.

Performance Evaluation of Relay Selection Schemes in Beacon-Assisted Dual-Hop Cognitive Radio Wireless Sensor Networks under Impact of Hardware Noises.

Science.gov (United States)

Hieu, Tran Dinh; Duy, Tran Trung; Dung, Le The; Choi, Seong Gon

2018-06-05

To solve the problem of energy constraints and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive the exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

Alternate transmission relaying based on interference alignment in 3-relay half-duplex MIMO systems

KAUST Repository

Park, Seongho; Park, Kihong; Ko, Youngchai; Alouini, Mohamed-Slim

2012-01-01

In a half-duplex relaying, the capacity pre-log factor 1/2 is a major drawback in spectral efficiency. This paper proposes a linear precoding/decoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can suppress the inter-relay interference resulting from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2012 IEEE.

Alternate transmission relaying based on interference alignment in 3-relay half-duplex MIMO systems

KAUST Repository

Park, Seongho

2012-09-01

In a half-duplex relaying, the capacity pre-log factor 1/2 is a major drawback in spectral efficiency. This paper proposes a linear precoding/decoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can suppress the inter-relay interference resulting from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2012 IEEE.

Joint sub-carrier pairing and resource allocation for cognitive networks with adaptive relaying

KAUST Repository

Soury, Hamza; Bader, F.; Shaat, M.; Alouini, Mohamed-Slim

2013-01-01

Relayed transmission in a cognitive radio (CR) environment could be used to increase the coverage and capacity of communication system that benefits already from the efficient management of the spectrum developed by CR. Furthermore, there are many types of cooperative communications, including decode-and-forward (DAF) and amplify-and-forward (AAF). In this paper, these techniques are combined in an adaptive mode to benefit from its forwarding advantages; this mode is called adaptive relaying protocol (ARP). Moreover, this work focuses on the joint power allocation in a cognitive radio system in a cooperative mode that operates ARP in multi-carrier mode. The multi-carrier scenario is used in an orthogonal frequency division multiplexing (OFDM) mode, and the problem is formulated to maximize the end-to-end rate by searching the best power allocation at the transmitters. This work includes, besides the ARP model, a sub-carrier pairing strategy that allows the relays to switch to the best sub-carrier pairs to increase the throughput. The optimization problem is formulated and solved under the interference and power budget constraints using the sub-gradient algorithm. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques. The results show also the consequence of the choice of the pairing strategy. 2013 Stolojescu-Crisan and Isar; licensee Springer.

Joint sub-carrier pairing and resource allocation for cognitive networks with adaptive relaying

KAUST Repository

Soury, Hamza

2013-11-09

Relayed transmission in a cognitive radio (CR) environment could be used to increase the coverage and capacity of communication system that benefits already from the efficient management of the spectrum developed by CR. Furthermore, there are many types of cooperative communications, including decode-and-forward (DAF) and amplify-and-forward (AAF). In this paper, these techniques are combined in an adaptive mode to benefit from its forwarding advantages; this mode is called adaptive relaying protocol (ARP). Moreover, this work focuses on the joint power allocation in a cognitive radio system in a cooperative mode that operates ARP in multi-carrier mode. The multi-carrier scenario is used in an orthogonal frequency division multiplexing (OFDM) mode, and the problem is formulated to maximize the end-to-end rate by searching the best power allocation at the transmitters. This work includes, besides the ARP model, a sub-carrier pairing strategy that allows the relays to switch to the best sub-carrier pairs to increase the throughput. The optimization problem is formulated and solved under the interference and power budget constraints using the sub-gradient algorithm. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques. The results show also the consequence of the choice of the pairing strategy. 2013 Stolojescu-Crisan and Isar; licensee Springer.

Coordinated Direct and Relay Transmission with Linear Non-Regenerative Relay Beamforming

DEFF Research Database (Denmark)

Sun, Fan; De Carvalho, Elisabeth; Popovski, Petar

2012-01-01

Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying, but also more general traffic scenarios, such as coordinated direct and relay (CDR) transmissions. In a CDR scheme the relay has a central...... role in managing the interference and boosting the overall system performance. In this letter we consider the case in which an amplify-and-forward relay has multiple antennas and can use beamforming to support the coordinated transmissions. We focus on one representative traffic type with one uplink...... user and one downlink user. Two different criteria for relay beamforming are analyzed: maximal weighted sum-rate and maximization of the worst-case weighted SNR. We propose iterative optimal solutions, as well as low-complexity near-optimal solutions....

Radioisotope relay instrument

International Nuclear Information System (INIS)

Pozdnyakov, V.N.; Sazonov, O.L.; Taksar, I.M.; Tesnavs, Eh.R.; Yanushkovskij, V.A.

1974-01-01

The paper describes a radioisotope relay device containing a radiation source, a detector, an electronic relay block with a comparative threshold mechanism. The device differs from previously known ones in that, for the purpose of increasing stability and speed of action, the electronic relay block is a separate unit and contains two threshold pulse generators which are joined up, across series-connected ''and'' and ''or'' elements, with one of the inputs of the comparative threshold mechanism, whose second input is connected with a detector and whose outputs are connected with a relay element connected by feedback with the above-mentioned ''and'' elements. (author)

Decode and Zero-Forcing Forward Relaying with Relay Selection in Cognitive Radio Systems

KAUST Repository

Park, Kihong

2014-05-01

In this paper, we investigate a cognitive radio (CR) relay network with multiple relay nodes that help forwarding the signal of CR users. Best relay selection is considered to take advantage of its low complexity of implementation. When the primary user (PU) is located close to the relay nodes, the performance of the secondary network is severely degraded due to the interference power constraint during the transmission in the second hop. We propose a decode and zero-forcing forward scheme to suppress the interference power at the relay nodes and analyze the statistics of the end-to-end signal-to-noise ratio when the relay nodes are located arbitrarily and experience therefore non-identical Rayleigh fading channels. Numerical results validate our theoretical results and show that our proposed scheme improves the performance of the CR network when the PU is close to the relay nodes. © 2014 IEEE.

On the achievable degrees of freedom of alternate MIMO relaying with multiple AF relays

KAUST Repository

Park, Kihong

2012-03-01

In this paper, we consider a two-hop relaying network where one source, one destination, and multiple amplify-and-forward (AF) relays equipped with M antennas operate in a half-duplex mode. In order to compensate for the inherent loss of capacity pre-log factor of 1/2 due to half-duplex relaying, we propose a new transmission protocol which combines alternate relaying and inter-relay interference alignment. We prove that the proposed scheme can (i) exploits M degrees of freedom (DOFs) and (ii) perfectly recover the pre-log factor loss if the number of relays is at least six. From our selected numerical results, we show that our proposed scheme gives significant improvement over conventional AF relaying which offers only M/2 DOFs. © 2012 IEEE.

Advanced Strategic and Tactical Relay Request Management for the Mars Relay Operations Service

Science.gov (United States)

Allard, Daniel A.; Wallick, Michael N.; Gladden, Roy E.; Wang, Paul; Hy, Franklin H.

2013-01-01

This software provides a new set of capabilities for the Mars Relay Operations Service (MaROS) in support of Strategic and Tactical relay, including a highly interactive relay request Web user interface, mission control over relay planning time periods, and mission management of allowed strategic vs. tactical request parameters. Together, these new capabilities expand the scope of the system to include all elements critical for Tactical relay operations. Planning of replay activities spans a time period that is split into two distinct phases. The first phase is called Strategic, which begins at the time that relay opportunities are identified, and concludes at the point that the orbiter generates the flight sequences for on board execution. Any relay request changes from this point on are called Tactical. Tactical requests, otherwise called Orbit - er Relay State Changes (ORSC), are highly restricted in terms of what types of changes can be made, and the types of parameters that can be changed may differ from one orbiter to the next. For example, one orbiter may be able to delay the start of a relay request, while another may not. The legacy approach to ORSC management involves exchanges of e-mail with "requests for change" and "acknowledgement of approval," with no other tracking of changes outside of e-mail folders. MaROS Phases 1 and 2 provided the infrastructure for strategic relay for all supported missions. This new version, 3.0, introduces several capabilities that fully expand the scope of the system to include tactical relay. One new feature allows orbiter users to manage and "lock" Planning Periods, which allows the orbiter team to formalize the changeover from Strategic to Tactical operations. Another major feature allows users to interactively submit tactical request changes via a Web user interface. A third new feature allows orbiter missions to specify allowed tactical updates, which are automatically incorporated into the tactical change process

Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

KAUST Repository

Pandarakkottilil, Ubaidulla

2011-11-01

In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a MIMO-relay node. The channel state information (CSI) available at the relay node is assumed to be imperfect. We consider robust designs for two models of CSI error. The first model is a stochastic error (SE) model, where the probability distribution of the CSI error is Gaussian. This model is applicable when the imperfect CSI is mainly due to errors in channel estimation. For this model, we propose robust minimum sum mean square error (SMSE), MSE-balancing, and relay transmit power minimizing precoder designs. The next model for the CSI error is a norm-bounded error (NBE) model, where the CSI error can be specified by an uncertainty set. This model is applicable when the CSI error is dominated by quantization errors. In this case, we adopt a worst-case design approach. For this model, we propose a robust precoder design that minimizes total relay transmit power under constraints on MSEs at the destination nodes. We show that the proposed robust design problems can be reformulated as convex optimization problems that can be solved efficiently using interior-point methods. We demonstrate the robust performance of the proposed design through simulations. © 2011 IEEE.

NRC Information No. 88-58: Potential problems with ASEA Brown Boveri ITE-51L time-overcurrent relays

International Nuclear Information System (INIS)

Rossi, C.E.

1992-01-01

Several spurious actuations of ASEA Brown Boveri (ABB) ITE-51L relays have occurred at the Beaver Valley nuclear power plant. These actuations resulted in unnecessary interruptions of the electrical power supply to safety-related equipment. The ITE-51L relays monitor circuit current. When the magnitude of the current exceeds a reference value for a specific duration, the relay actuates to energize the circuit breaker's trip coil. The licensee has determined that the spurious relay actuations were caused by faulty silicon-controlled rectifiers (SCRs) that were manufactured by the Motorola Company. SCRs are solid-state devices that are used as electronic switches in electrical circuits. When a voltage is applied across the terminals of the SCR, the device is designed to allow current to flow only when ''gated'' or switched on by the proper electrical signal. The SCRs that failed at Beaver Valley allowed current to flow in the absence of the proper gating signal. These ''leakage'' currents were of sufficient magnitude to energize the trip coil of the associated circuit breaker. The licensee was informed by Motorola that SCRs manufactured between the late 1970s and early 1980s are susceptible to this mode of failure and that these SCRs are likely to fail within the first 2 years of service. Since 1982, all SCRs manufactured by Motorola have been subjected to a ''burn-in'' test. In this test, the SCRs are placed in a high-temperature environment both with and without voltage applied. SCRs that pass this test are expected to perform normally for an extended period

Decode and Zero-Forcing Forward Relaying with Relay Selection in Cognitive Radio Systems

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim

2014-01-01

In this paper, we investigate a cognitive radio (CR) relay network with multiple relay nodes that help forwarding the signal of CR users. Best relay selection is considered to take advantage of its low complexity of implementation. When the primary

Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

KAUST Repository

Pandarakkottilil, Ubaidulla; Chockalingam, A.

2011-01-01

In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a

CERN Relay Race

CERN Document Server

CERN Running Club

2010-01-01

The CERN relay race will take place around the Meyrin site on Thursday 20 May, starting at 12.15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the route, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay

Alternate MIMO relaying with three AF relays using interference alignment

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim

2012-01-01

In this paper, we study a two-hop half-duplex relaying network with one source, one destination, and three amplify-and-forward (AF) relays equipped with M antennas each. We consider alternate transmission to compensate for the inherent loss

Rate Maximization in MIMO Decode-and-Forward Communications With an EH Relay and Possibly Imperfect CSI

KAUST Repository

Benkhelifa, Fatma

2016-08-29

In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) in a multiple-input multiple-output (MIMO) decode-and-forward (DF) relay system where the relay is an energy harvesting (EH) multi-antenna node equipped with an EH receiver and an information decoding (ID) receiver. The relay harvests the energy from the radio frequency (RF) signals sent by the source and uses it to forward the signals to the destination. The main objective in this paper is to maximize the achievable transmission rate of the overall link by optimizing the source/relay precoders. First, we study an upper bound on the maximum achievable rate where we assume that the EH and ID receivers operate simultaneously and have access to the whole power of the received signals. Afterwards, we study two practical schemes, which are the power splitting (PS) and time switching (TS) schemes, where the ID and EH receivers have partial access to the power or duration of the received signals. For each scheme, we have studied the complexity and the performance comparison. In addition, we considered the case of the imperfect channel estimation error and we have observed its impact on the achievable end-to-end rate and the harvested energy at the relay. © 1972-2012 IEEE.

80537 based distance relay

DEFF Research Database (Denmark)

Pedersen, Knud Ole Helgesen

1999-01-01

A method for implementing a digital distance relay in the power system is described.Instructions are given on how to program this relay on a 80537 based microcomputer system.The problem is used as a practical case study in the course 53113: Micocomputer applications in the power system.The relay...

Relay Selection and Resource Allocation in One-Way and Two-Way Cognitive Relay Networks

KAUST Repository

Alsharoa, Ahmad M.

2013-01-01

In this work, the problem of relay selection and resource power allocation in one- way and two-way cognitive relay networks using half duplex channels with different relaying protocols is investigated. Optimization problems for both single

A genetic algorithm for multiple relay selection in two-way relaying cognitive radio networks

KAUST Repository

Alsharoa, Ahmad M.; Ghazzai, Hakim; Alouini, Mohamed-Slim

2013-01-01

In this paper, we investigate a multiple relay selection scheme for two-way relaying cognitive radio networks where primary users and secondary users operate on the same frequency band. More specifically, cooperative relays using Amplifyand- Forward

Efficient incremental relaying

KAUST Repository

Fareed, Muhammad Mehboob; Alouini, Mohamed-Slim

2013-01-01

We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission

Outage performance of two-way DF relaying systems with a new relay selection metric

KAUST Repository

Hyadi, Amal; Benjillali, Mustapha; Alouini, Mohamed-Slim

2012-01-01

This paper investigates a new constrained relay selection scheme for two-way relaying systems where two end terminals communicate simultaneously via a relay. The introduced technique is based on the maximization of the weighted sum rate of both

76 FR 24442 - Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services and...

Science.gov (United States)

2011-05-02

... same meaning as the terms ``small business,'' ``small organization,'' and ``small governmental...] Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services and Speech-to... Commission's Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services...

Alternate transmission with half-duplex relaying in MIMO interference relay networks

KAUST Repository

Park, Seongho; Ko, Youngchai; Park, Kihong; Alouini, Mohamed-Slim

2013-01-01

In this paper, we consider an alternate transmission scheme for a multiple-input multiple-output interference relay channel where multiple sources transmit their own signals to their corresponding destinations via one of two relaying groups

Opportunistic Relay Selection With Limited Feedback

KAUST Repository

Eltayeb, Mohammed E.; Elkhalil, Khalil; Bahrami, Hamid Reza; Al-Naffouri, Tareq Y.

2015-01-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Generally, relay selection algorithms require channel state information (CSI) feedback from all cooperating relays to make a selection decision

CERN Relay Race

CERN Document Server

2008-01-01

The CERN relay race will take place around the Meyrin site on Thursday 5 June starting at 12:15 p.m. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site. You can access the online registration form at: http://cern.ch/club-running-relay/form.html

CERN Relay Race

CERN Document Server

2007-01-01

The CERN relay race will take place around the Meyrin site on Wednesday 23 May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site. You can access the online registration form at: http://cern.ch/club-running-relay/form.html

Power system relaying

CERN Document Server

Horowitz, Stanley H; Niemira, James K

2013-01-01

The previous three editions of Power System Relaying offer comprehensive and accessible coverage of the theory and fundamentals of relaying and have been widely adopted on university and industry courses worldwide. With the third edition, the authors have added new and detailed descriptions of power system phenomena such as stability, system-wide protection concepts and discussion of historic outages. Power System Relaying, 4th Edition continues its role as an outstanding textbook on power system protection for senior and graduate students in the field of electric power engineering and a refer

Achievable rate maximization for decode-and-forward MIMO-OFDM networks with an energy harvesting relay.

Science.gov (United States)

Du, Guanyao; Yu, Jianjun

2016-01-01

This paper investigates the system achievable rate for the multiple-input multiple-output orthogonal frequency division multiplexing (MIMO-OFDM) system with an energy harvesting (EH) relay. Firstly we propose two protocols, time switching-based decode-and-forward relaying (TSDFR) and a flexible power splitting-based DF relaying (PSDFR) protocol by considering two practical receiver architectures, to enable the simultaneous information processing and energy harvesting at the relay. In PSDFR protocol, we introduce a temporal parameter to describe the time division pattern between the two phases which makes the protocol more flexible and general. In order to explore the system performance limit, we discuss the system achievable rate theoretically and formulate two optimization problems for the proposed protocols to maximize the system achievable rate. Since the problems are non-convex and difficult to solve, we first analyze them theoretically and get some explicit results, then design an augmented Lagrangian penalty function (ALPF) based algorithm for them. Numerical results are provided to validate the accuracy of our analytical results and the effectiveness of the proposed ALPF algorithm. It is shown that, PSDFR outperforms TSDFR to achieve higher achievable rate in such a MIMO-OFDM relaying system. Besides, we also investigate the impacts of the relay location, the number of antennas and the number of subcarriers on the system performance. Specifically, it is shown that, the relay position greatly affects the system performance of both protocols, and relatively worse achievable rate is achieved when the relay is placed in the middle of the source and the destination. This is different from the MIMO-OFDM DF relaying system without EH. Moreover, the optimal factor which indicates the time division pattern between the two phases in the PSDFR protocol is always above 0.8, which means that, the common division of the total transmission time into two equal phases in

Downregulation of RWA genes in hybrid aspen affects xylan acetylation and wood saccharification.

Science.gov (United States)

Pawar, Prashant Mohan-Anupama; Ratke, Christine; Balasubramanian, Vimal K; Chong, Sun-Li; Gandla, Madhavi Latha; Adriasola, Mathilda; Sparrman, Tobias; Hedenström, Mattias; Szwaj, Klaudia; Derba-Maceluch, Marta; Gaertner, Cyril; Mouille, Gregory; Ezcurra, Ines; Tenkanen, Maija; Jönsson, Leif J; Mellerowicz, Ewa J

2017-06-01

High acetylation of angiosperm wood hinders its conversion to sugars by glycoside hydrolases, subsequent ethanol fermentation and (hence) its use for biofuel production. We studied the REDUCED WALL ACETYLATION (RWA) gene family of the hardwood model Populus to evaluate its potential for improving saccharification. The family has two clades, AB and CD, containing two genes each. All four genes are expressed in developing wood but only RWA-A and -B are activated by master switches of the secondary cell wall PtNST1 and PtMYB21. Histochemical analysis of promoter::GUS lines in hybrid aspen (Populus tremula × tremuloides) showed activation of RWA-A and -B promoters in the secondary wall formation zone, while RWA-C and -D promoter activity was diffuse. Ectopic downregulation of either clade reduced wood xylan and xyloglucan acetylation. Suppressing both clades simultaneously using the wood-specific promoter reduced wood acetylation by 25% and decreased acetylation at position 2 of Xylp in the dimethyl sulfoxide-extracted xylan. This did not affect plant growth but decreased xylose and increased glucose contents in the noncellulosic monosaccharide fraction, and increased glucose and xylose yields of wood enzymatic hydrolysis without pretreatment. Both RWA clades regulate wood xylan acetylation in aspen and are promising targets to improve wood saccharification. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Precoding Design of MIMO Amplify-and-Forward Communication System With an Energy Harvesting Relay and Possibly Imperfect CSI

KAUST Repository

Benkhelifa, Fatma

2017-03-02

In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) in a Multiple-Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication system where the relay is an energy harvesting (EH) node and harvests the energy the signals transmitted from the source. The harvested energy is partially used to forward signals from the source to the destination, and the remaining energy is stored for other usages. The SWIPT in relay-assisted communication is interesting as long as the relay stores energy from the source and the destination receives successfully the data from the source. In this context, we propose to investigate the source and relay precoders that characterize the relationship between the achievable stored energy at the relay and the achievable sourceto- destination rate, namely the rate-stored energy (R-E) tradeo region. First, we consider the ideal scheme where there is the simultaneous operation of the EH and ID receivers at the relay. Then, we consider practical schemes such as the power splitting (PS) and the time switching (TS) that separate the operation of EH and information decoding (ID) receivers over power domain or time domain, respectively. Moreover, we study the case of imperfect channel state information (CSI) at the relay and the destination and characterize its impact on the achievable R-E region. Through the simulation results, we show the eect of the position of the relay and the channel uncertainty on the achievable R-E regions of all the schemes when the used energy at the relay is constant or variable. We also show that, although it provides an outer bound on the achievable rate-energy region in one-hop MIMO systems, the ideal scheme provides only an upper bound on the maximum achievable end-to-end rate and not an outer bound on the R-E region.

Analysis of acetylation stoichiometry suggests that SIRT3 repairs nonenzymatic acetylation lesions

DEFF Research Database (Denmark)

Weinert, Brian T; Moustafa, Tarek; Iesmantavicius, Vytautas

2015-01-01

or suppresses acetylation. Using quantitative mass spectrometry, we measured acetylation stoichiometry in mouse liver tissue and found that SIRT3 suppressed acetylation to a very low stoichiometry at its target sites. By examining acetylation changes in the liver, heart, brain, and brown adipose tissue...... of fasted mice, we found that SIRT3-targeted sites were mostly unaffected by fasting, a dietary manipulation that is thought to regulate metabolism through SIRT3-dependent deacetylation. Globally increased mitochondrial acetylation in fasted liver tissue, higher stoichiometry at mitochondrial acetylation...... functions as a protein repair factor that removes acetylation lesions from lysine residues....

Investigation into Contact Resistance And Damage of Metal Contacts Used in RF-MEMS Switches

Science.gov (United States)

2009-09-01

mechanically cycled by a piezo - electric transducer (PZT). The resistance through the simulated switch was measured using a four-wire measurement technique...determined that the microwave performance of a closed relay can be modeled as a simple resistor to a first order equivalent [106,108]. The relay resistance is...Therefore, a piezo device capable of precise higher frequency motion was chosen to provide cyclic contact motion. This device needed to be physically small

MIMO Four-Way Relaying

DEFF Research Database (Denmark)

Liu, Huaping; Sun, Fan; De Carvalho, Elisabeth

2013-01-01

Two-way relaying in wireless systems has initiated a large research effort during the past few years. Nevertheless, it represents only a specific traffic pattern and it is of interest to investigate other traffic patterns where such a simultaneous processing of information flows can bring...... performance advantage. In this paper we consider a \\emph{four-way relaying} multiple-input multiple-output (MIMO) scenario, where each of the two Mobile Stations (MSs) has a two-way connection to the same Base Station (BS), while each connection is through a dedicated Relay Station (RS). The RSs are placed...... the sum-rate of the new scheme for Decode-and-Forward (DF) operational model for the RS. We compare the performance with state-of-the-art reference schemes, based on two-way relaying with DF. The results indicate that the sum-rate of the two-phase four-way relaying scheme largely outperforms the four...

Performance analysis of two-way amplify and forward relaying with adaptive modulation over multiple relay network

KAUST Repository

Hwang, Kyusung; Ko, Youngchai; Alouini, Mohamed-Slim

2011-01-01

In this letter, we propose two-way amplify-and-forward relaying in conjunction with adaptive modulation in order to improve spectral efficiency of relayed communication systems while monitoring the required error performance. We also consider a multiple relay network where only the best relay node is utilized so that the diversity order increases while maintaining a low complexity of implementation as the number of relays increases. Based on the best relay selection criterion, we offer an upper bound on the signal-to-noise ratio to keep the performance analysis tractable. Our numerical examples show that the proposed system offers a considerable gain in spectral efficiency while satisfying the error rate requirements. © 2011 IEEE.

Performance analysis of two-way amplify and forward relaying with adaptive modulation over multiple relay network

KAUST Repository

Hwang, Kyusung

2011-02-01

In this letter, we propose two-way amplify-and-forward relaying in conjunction with adaptive modulation in order to improve spectral efficiency of relayed communication systems while monitoring the required error performance. We also consider a multiple relay network where only the best relay node is utilized so that the diversity order increases while maintaining a low complexity of implementation as the number of relays increases. Based on the best relay selection criterion, we offer an upper bound on the signal-to-noise ratio to keep the performance analysis tractable. Our numerical examples show that the proposed system offers a considerable gain in spectral efficiency while satisfying the error rate requirements. © 2011 IEEE.

Opportunistic Relay Selection With Limited Feedback

KAUST Repository

Eltayeb, Mohammed E.

2015-08-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Generally, relay selection algorithms require channel state information (CSI) feedback from all cooperating relays to make a selection decision. This requirement poses two important challenges, which are often neglected in the literature. Firstly, the fed back channel information is usually corrupted by additive noise. Secondly, CSI feedback generates a great deal of feedback overhead (air-time) that could result in significant performance hits. In this paper, we propose a compressive sensing (CS) based relay selection algorithm that reduces the feedback overhead of relay networks under the assumption of noisy feedback channels. The proposed algorithm exploits CS to first obtain the identity of a set of relays with favorable channel conditions. Following that, the CSI of the identified relays is estimated using least squares estimation without any additional feedback. Both single and multiple relay selection cases are considered. After deriving closed-form expressions for the asymptotic end-to-end SNR at the destination and the feedback load for different relaying protocols, we show that CS-based selection drastically reduces the feedback load and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback. © 1972-2012 IEEE.

Ready, steady… relay!

CERN Multimedia

2008-01-01

Thursday 5 June. With another year comes another success for CERN’s Relay Race. With 76 teams taking part it was the second highest turnout in the race’s history. ‘The Shabbys’ won the relay race in 10 minutes 51 seconds.As popular as ever, this year the relay race took on the atmosphere of a mini carnival. Gathering on the lawn outside Restaurant 1, various stalls and attractions added to the party feeling of the event, with beer courtesy of ‘AGLUP’, the Belgian beer club, and a wandering jazz group entertaining spectators and competitors alike. Reflecting the greater involvement of other associations in the relay race, the president of the Staff Association Clubs Committee, James Purvis, was the guest of honour, launching the start of the race and presenting the prizes. As regular followers of the race could have probably predicted, The Shabbys were once again victorious and claimed first place. The team members th...

Acetyl coenzyme A: alpha-glucosaminide N-acetyltransferase. Evidence for a transmembrane acetylation mechanism

International Nuclear Information System (INIS)

Bame, K.J.; Rome, L.H.

1985-01-01

The lysosomal membrane enzyme acetyl-CoA: alpha-glucosaminide N-acetyltransferase catalyzes the transfer of an acetyl group from acetyl-CoA to terminal alpha-linked glucosamine residues of heparan sulfate. The reaction mechanism was examined using highly purified lysosomal membranes from rat liver. The reaction was followed by measuring the acetylation of a monosaccharide acetyl acceptor, glucosamine. The enzyme reaction was optimal above pH 5.5, and a 2-3-fold stimulation of activity was observed when the membranes were assayed in the presence of 0.1% taurodeoxycholate. Double reciprocal analysis and product inhibition studies indicated that the enzyme works by a Di-Iso Ping Pong Bi Bi mechanism. Further evidence to support this mechanism was provided by characterization of the enzyme half-reactions. Membranes incubated with acetyl-CoA and [ 3 H]CoA were found to produce acetyl-[ 3 H]CoA. This exchange was optimal at pH values above 7.0. Treating membranes with [ 3 H] acetyl-CoA resulted in the formation of an acetyl-enzyme intermediate. The acetyl group could then be transferred to glucosamine, forming [ 3 H]N-acetylglucosamine. The transfer of the acetyl group from the enzyme to glucosamine was optimal between pH 4 and 5. The results suggest that acetyl-CoA does not cross the lysosomal membrane. Instead, the enzyme is acetylated on the cytoplasmic side of the lysosome and the acetyl group is then transferred to the inside where it is used to acetylate heparan sulfate

A genetic algorithm for multiple relay selection in two-way relaying cognitive radio networks

KAUST Repository

Alsharoa, Ahmad M.

2013-09-01

In this paper, we investigate a multiple relay selection scheme for two-way relaying cognitive radio networks where primary users and secondary users operate on the same frequency band. More specifically, cooperative relays using Amplifyand- Forward (AF) protocol are optimally selected to maximize the sum rate of the secondary users without degrading the Quality of Service (QoS) of the primary users by respecting a tolerated interference threshold. A strong optimization tool based on genetic algorithm is employed to solve our formulated optimization problem where discrete relay power levels are considered. Our simulation results show that the practical heuristic approach achieves almost the same performance of the optimal multiple relay selection scheme either with discrete or continuous power distributions. Copyright © 2013 by the Institute of Electrical and Electronic Engineers, Inc.

Iterative Relay Scheduling with Hybrid ARQ under Multiple User Equipment (Type II) Relay Environments

KAUST Repository

Nam, Sung Sik

2018-01-09

In this work, we propose an iterative relay scheduling with hybrid ARQ (IRS-HARQ) scheme which realizes fast jump-in/successive relaying and subframe-based decoding under the multiple user equipment (UE) relay environments applicable to the next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed IRS-HARQ aims to increase the achievable data rate by iteratively scheduling a relatively better UE relay closer to the end user in a probabilistic sense, provided that the relay-to-end user link should be operated in an open-loop and transparent mode. The latter is due to the fact that not only there are no dedicated control channels between the UE relay and the end user but also a new cell is not created. Under this open-loop and transparent mode, our proposed protocol is implemented by partially exploiting the channel state information based on the overhearing mechanism of ACK/NACK for HARQ. Further, the iterative scheduling enables UE-to-UE direct communication with proximity that offers spatial frequency reuse and energy saving.

Relay Selection with Limited and Noisy Feedback

KAUST Repository

Eltayeb, Mohammed E.

2016-01-28

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Nonetheless, relay selection algorithms generally require error-free channel state information (CSI) from all cooperating relays. Practically, CSI acquisition generates a great deal of feedback overhead that could result in significant transmission delays. In addition to this, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we propose a relay selection algorithm that tackles the above challenges. Instead of allocating each relay a dedicated channel for feedback, all relays share a pool of feedback channels. Following that, each relay feeds back its identity only if its effective channel (source-relay-destination) exceeds a threshold. After deriving closed-form expressions for the feedback load and the achievable rate, we show that the proposed algorithm drastically reduces the feedback overhead and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback from all relays. © 2015 IEEE.

Non-enzymatic N-acetylation of Lysine Residues by AcetylCoA Often Occurs via a Proximal S-acetylated Thiol Intermediate Sensitive to Glyoxalase II

Directory of Open Access Journals (Sweden)

Andrew M. James

2017-02-01

Full Text Available Summary: Acetyl coenzyme A (AcCoA, a key intermediate in mitochondrial metabolism, N-acetylates lysine residues, disrupting and, in some cases, regulating protein function. The mitochondrial lysine deacetylase Sirtuin 3 (Sirt3 reverses this modification with benefits reported in diabetes, obesity, and aging. We show that non-enzymatic lysine N-acetylation by AcCoA is greatly enhanced by initial acetylation of a cysteine residue, followed by SN-transfer of the acetyl moiety to a nearby lysine on mitochondrial proteins and synthetic peptides. The frequent occurrence of an S-acetyl intermediate before lysine N-acetylation suggests that proximity to a thioester is a key determinant of lysine susceptibility to acetylation. The thioesterase glyoxalase II (Glo2 can limit protein S-acetylation, thereby preventing subsequent lysine N-acetylation. This suggests that the hitherto obscure role of Glo2 in mitochondria is to act upstream of Sirt3 in minimizing protein N-acetylation, thus limiting protein dysfunction when AcCoA accumulates. : James et al. show that the non-enzymatic N-acetylation of lysine residues in mitochondrial proteins frequently occurs via a proximal S-acetylated thiol intermediate. Glutathione equilibrates with this intermediate, allowing the thioesterase glyoxalase II to limit protein lysine N-acetylation. These findings expand our understanding of how protein acetylation arises. Keywords: AcetylCoA, lysine acetylation, glyoxalase

Acetyl-Phosphate Is a Critical Determinant of Lysine Acetylation in E. coli

DEFF Research Database (Denmark)

Weinert, Brian T; Iesmantavicius, Vytautas; Wagner, Sebastian A

2013-01-01

Lysine acetylation is a frequently occurring posttranslational modification in bacteria; however, little is known about its origin and regulation. Using the model bacterium Escherichia coli (E. coli), we found that most acetylation occurred at a low level and accumulated in growth-arrested cells...... acetylate lysine residues in vitro and that AcP levels are correlated with acetylation levels in vivo, suggesting that AcP may acetylate proteins nonenzymatically in cells. These results uncover a critical role for AcP in bacterial acetylation and indicate that most acetylation in E. coli occurs at a low...

Application of the voltage biased digital relay for the optimal protection of high inertia drive induction motors

International Nuclear Information System (INIS)

Choi, D. B.

1999-01-01

This paper describes typical protection schemes for large-size high inertia drive motor that are generally rotor thermal limited. Difficult and variable starting conditions of the large-size high inertia drive motor and compromises in the selection and setting of the protective devices are frequently encountered. The motors that typically encounter severe starting duty and present difficulties in achieving full motor protection are reactor coolant pumps (RCPs), blowers and compressors. For difficult starting conditions that are encountered by the large-size high inertia drive motors, state-of-the-art computer based calculations are capable of providing realistic predictions of the band of margin available for applying the protective relay. Based on the analysis of starting characteristics of large-size high inertia drive motors, this paper recommends that the optimal protection scheme for high inertia drive motors for nuclear power plants can be achieved by using the voltage biased digital relay instead of a speed switch and conventional overcurrent relays. (author)

Optimal relay selection and power allocation for cognitive two-way relaying networks

KAUST Repository

Pandarakkottilil, Ubaidulla; Aï ssa, Sonia

2012-01-01

In this paper, we present an optimal scheme for power allocation and relay selection in a cognitive radio network where a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relays

Buffer-Aided Relaying with Adaptive Link Selection

DEFF Research Database (Denmark)

Zlatanov, Nikola; Schober, Robert; Popovski, Petar

2013-01-01

In this paper, we consider a simple network consisting of a source, a half-duplex decode-and-forward relay, and a destination. We propose a new relaying protocol employing adaptive link selection, i.e., in any given time slot, based on the channel state information of the source-relay and the relay......-destination link a decision is made whether the source or the relay transmits. In order to avoid data loss at the relay, adaptive link selection requires the relay to be equipped with a buffer such that data can be queued until the relay-destination link is selected for transmission. We study both delay......-constrained and delay-unconstrained transmission. For the delay-unconstrained case, we characterize the optimal link selection policy, derive the corresponding throughput, and develop an optimal power allocation scheme. For the delay-constrained case, we propose to starve the buffer of the relay by choosing...

Relay Selection with Limited and Noisy Feedback

KAUST Repository

Eltayeb, Mohammed E.; Elkhalil, Khalil; Mas'ud, Abdullahi Abubakar; Al-Naffouri, Tareq Y.

2016-01-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Nonetheless, relay selection algorithms generally require error-free channel state information (CSI) from all cooperating relays. Practically, CSI

CERN Relay Race

CERN Multimedia

2009-01-01

The CERN relay race, now in its 39th year, is already a well-known tradition, but this year the organizers say the event will have even more of a festival feeling. Just off the starting line of the CERN relay race.For the past few years, spectators and runners at the CERN relay race have been able to enjoy a beer while listening to music from the CERN music and jazz clubs. But this year the organizers are aiming for "even more of a festival atmosphere". As David Nisbet, President of the CERN running club and organizer of the relay race, says: "Work is not just about getting your head down and doing the theory, it’s also about enjoying the company of your colleagues." This year, on top of music from the Santa Luis Band and the Canettes Blues Band, there will be demonstrations from the Aikido and softball clubs, a stretching session by the Fitness club, as well as various stalls and of course, the well-earned beer from AGLUP, the B...

Physical Layer Security Using Two-Path Successive Relaying

Directory of Open Access Journals (Sweden)

Qian Yu Liau

2016-06-01

Full Text Available Relaying is one of the useful techniques to enhance wireless physical-layer security. Existing literature shows that employing full-duplex relay instead of conventional half-duplex relay improves secrecy capacity and secrecy outage probability, but this is at the price of sophisticated implementation. As an alternative, two-path successive relaying has been proposed to emulate operation of full-duplex relay by scheduling a pair of half-duplex relays to assist the source transmission alternately. However, the performance of two-path successive relaying in secrecy communication remains unexplored. This paper proposes a secrecy two-path successive relaying protocol for a scenario with one source, one destination and two half-duplex relays. The relays operate alternately in a time division mode to forward messages continuously from source to destination in the presence of an eavesdropper. Analytical results reveal that the use of two half-duplex relays in the proposed scheme contributes towards a quadratically lower probability of interception compared to full-duplex relaying. Numerical simulations show that the proposed protocol achieves the ergodic achievable secrecy rate of full-duplex relaying while delivering the lowest probability of interception and secrecy outage probability compared to the existing half duplex relaying, full duplex relaying and full duplex jamming schemes.

Handover Framework for Relay Enhanced LTE Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Van Phan, Vinh; Raaf, Bernhard

2009-01-01

Relaying is one of the proposed technologies for future releases of UTRAN Long Term Evolution (LTE) networks. Introducing relaying is expected to increase the coverage and capacity of LTE networks. In order to enable relaying, the architecture, protocol and radio resource management procedures...... of LTE, such as handover, have to be modified. A user can be handed over not only between two base stations, but also between relays and base stations, and between two relays. With the introduction of relaying, there is a need for a new procedure to hand over a relay and all its associated users...... to another base station, allowing a flexible and dynamic relay deployment. In this paper, we extend the LTE release 8 handover mechanisms so that it can accommodate these new handover functionalities in a flexible manner....

Acetylation-mediated suppression of transcription-independent memory: bidirectional modulation of memory by acetylation.

Directory of Open Access Journals (Sweden)

Katja Merschbaecher

Full Text Available Learning induced changes in protein acetylation, mediated by histone acetyl transferases (HATs, and the antagonistic histone deacetylases (HDACs play a critical role in memory formation. The status of histone acetylation affects the interaction between the transcription-complex and DNA and thus regulates transcription-dependent processes required for long-term memory (LTM. While the majority of studies report on the role of elevated acetylation in memory facilitation, we address the impact of both, increased and decreased acetylation on formation of appetitive olfactory memory in honeybees. We show that learning-induced changes in the acetylation of histone H3 at aminoacid-positions H3K9 and H3K18 exhibit distinct and different dynamics depending on the training strength. A strong training that induces LTM leads to an immediate increase in acetylation at H3K18 that stays elevated for hours. A weak training, not sufficient to trigger LTM, causes an initial increase in acetylation at H3K18, followed by a strong reduction in acetylation at H3K18 below the control group level. Acetylation at position H3K9 is not affected by associative conditioning, indicating specific learning-induced actions on the acetylation machinery. Elevating acetylation levels by blocking HDACs after conditioning leads to an improved memory. While memory after strong training is enhanced for at least 2 days, the enhancement after weak training is restricted to 1 day. Reducing acetylation levels by blocking HAT activity after strong training leads to a suppression of transcription-dependent LTM. The memory suppression is also observed in case of weak training, which does not require transcription processes. Thus, our findings demonstrate that acetylation-mediated processes act as bidirectional regulators of memory formation that facilitate or suppress memory independent of its transcription-requirement.

Optimal relay selection and power allocation for cognitive two-way relaying networks

KAUST Repository

Pandarakkottilil, Ubaidulla

2012-06-01

In this paper, we present an optimal scheme for power allocation and relay selection in a cognitive radio network where a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relays. The secondary nodes share the spectrum with a licensed primary user (PU), and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. We propose joint relay selection and optimal power allocation among the secondary user (SU) nodes achieving maximum throughput under transmit power and PU interference constraints. A closed-form solution for optimal allocation of transmit power among the SU transceivers and the SU relay is presented. Furthermore, numerical simulations and comparisons are presented to illustrate the performance of the proposed scheme. © 2012 IEEE.

Relay Architectures for 3GPP LTE-Advanced

Directory of Open Access Journals (Sweden)

Peters StevenW

2009-01-01

Full Text Available The Third Generation Partnership Project's Long Term Evolution-Advanced is considering relaying for cost-effective throughput enhancement and coverage extension. While analog repeaters have been used to enhance coverage in commercial cellular networks, the use of more sophisticated fixed relays is relatively new. The main challenge faced by relay deployments in cellular systems is overcoming the extra interference added by the presence of relays. Most prior work on relaying does not consider interference, however. This paper analyzes the performance of several emerging half-duplex relay strategies in interference-limited cellular systems: one-way, two-way, and shared relays. The performance of each strategy as a function of location, sectoring, and frequency reuse are compared with localized base station coordination. One-way relaying is shown to provide modest gains over single-hop cellular networks in some regimes. Shared relaying is shown to approach the gains of local base station coordination at reduced complexity, while two-way relaying further reduces complexity but only works well when the relay is close to the handset. Frequency reuse of one, where each sector uses the same spectrum, is shown to have the highest network throughput. Simulations with realistic channel models provide performance comparisons that reveal the importance of interference mitigation in multihop cellular networks.

Full-Duplex Relay Selection in Cognitive Underlay Networks

KAUST Repository

Khafagy, Mohammad Galal; Alouini, Mohamed-Slim; Aissa, Sonia

2017-01-01

In this work, we analyze the performance of full-duplex relay selection (FDRS) in spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay(s), thereby

Non-enzymatic N-acetylation of Lysine Residues by AcetylCoA Often Occurs via a Proximal S-acetylated Thiol Intermediate Sensitive to Glyoxalase II.

Science.gov (United States)

James, Andrew M; Hoogewijs, Kurt; Logan, Angela; Hall, Andrew R; Ding, Shujing; Fearnley, Ian M; Murphy, Michael P

2017-02-28

Acetyl coenzyme A (AcCoA), a key intermediate in mitochondrial metabolism, N-acetylates lysine residues, disrupting and, in some cases, regulating protein function. The mitochondrial lysine deacetylase Sirtuin 3 (Sirt3) reverses this modification with benefits reported in diabetes, obesity, and aging. We show that non-enzymatic lysine N-acetylation by AcCoA is greatly enhanced by initial acetylation of a cysteine residue, followed by SN-transfer of the acetyl moiety to a nearby lysine on mitochondrial proteins and synthetic peptides. The frequent occurrence of an S-acetyl intermediate before lysine N-acetylation suggests that proximity to a thioester is a key determinant of lysine susceptibility to acetylation. The thioesterase glyoxalase II (Glo2) can limit protein S-acetylation, thereby preventing subsequent lysine N-acetylation. This suggests that the hitherto obscure role of Glo2 in mitochondria is to act upstream of Sirt3 in minimizing protein N-acetylation, thus limiting protein dysfunction when AcCoA accumulates. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Capacity gains of buffer-aided moving relays

KAUST Repository

Zafar, Ammar

2017-03-14

This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

Capacity gains of buffer-aided moving relays

KAUST Repository

Zafar, Ammar; Shaqfeh, Mohammad; Alnuweiri, Hussein; Alouini, Mohamed-Slim

2017-01-01

This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond.

Science.gov (United States)

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2016-01-01

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment.

Performance analysis of opportunistic nonregenerative relaying

KAUST Repository

Tourki, Kamel; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Yang, Hongchuan

2013-01-01

Opportunistic relaying in cooperative communication depends on careful relay selection. However, the traditional centralized method used for opportunistic amplify-and-forward protocols requires precise measurements of channel state information at the destination. In this paper, we adopt the max-min criterion as a relay selection framework for opportunistic amplify-and-forward cooperative communications, which was exhaustively used for the decode-and-forward protocol, and offer an accurate performance analysis based on exact statistics of the local signal-to-noise ratios of the best relay. Furthermore, we evaluate the asymptotical performance and deduce the diversity order of our proposed scheme. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over Rayleigh fading channels, and we compare the max-min relay selection with their centralized channel state information-based and partial relay selection counterparts.

78 FR 40407 - Structure and Practices of the Video Relay Service Program: Telecommunications Relay Services and...

Science.gov (United States)

2013-07-05

...] Structure and Practices of the Video Relay Service Program: Telecommunications Relay Services and Speech-to... telecommunications relay services (TRS) program continues to offer functional equivalence to all eligible users and..., identified by CG Docket Nos. 10-51 and 03-123, by any of the following methods: Electronic Filers: Comments...

Structural, kinetic and proteomic characterization of acetyl phosphate-dependent bacterial protein acetylation.

Directory of Open Access Journals (Sweden)

Misty L Kuhn

Full Text Available The emerging view of Nε-lysine acetylation in eukaryotes is of a relatively abundant post-translational modification (PTM that has a major impact on the function, structure, stability and/or location of thousands of proteins involved in diverse cellular processes. This PTM is typically considered to arise by the donation of the acetyl group from acetyl-coenzyme A (acCoA to the ε-amino group of a lysine residue that is reversibly catalyzed by lysine acetyltransferases and deacetylases. Here, we provide genetic, mass spectrometric, biochemical and structural evidence that Nε-lysine acetylation is an equally abundant and important PTM in bacteria. Applying a recently developed, label-free and global mass spectrometric approach to an isogenic set of mutants, we detected acetylation of thousands of lysine residues on hundreds of Escherichia coli proteins that participate in diverse and often essential cellular processes, including translation, transcription and central metabolism. Many of these acetylations were regulated in an acetyl phosphate (acP-dependent manner, providing compelling evidence for a recently reported mechanism of bacterial Nε-lysine acetylation. These mass spectrometric data, coupled with observations made by crystallography, biochemistry, and additional mass spectrometry showed that this acP-dependent acetylation is both non-enzymatic and specific, with specificity determined by the accessibility, reactivity and three-dimensional microenvironment of the target lysine. Crystallographic evidence shows acP can bind to proteins in active sites and cofactor binding sites, but also potentially anywhere molecules with a phosphate moiety could bind. Finally, we provide evidence that acP-dependent acetylation can impact the function of critical enzymes, including glyceraldehyde-3-phosphate dehydrogenase, triosephosphate isomerase, and RNA polymerase.

Relay test program

International Nuclear Information System (INIS)

Bandyopadhyay, K.K.; Kunkel, C.; Shteyngart, S.

1994-02-01

This report presents the results of a relay test program conducted by Brookhaven National Laboratory (BNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC). The program is a continuation of an earlier test program the results of which were published in NUREG/CR-4867. The current program was carried out in two phases: electrical testing and vibration testing. The objective was primarily to focus on the electrical discontinuity or continuity of relays and circuit breaker tripping mechanisms subjected to electrical pulses and vibration loads. The electrical testing was conducted by KEMA-Powertest Company and the vibration testing was performed at Wyle Laboratories, Huntsville, Alabama. This report discusses the test procedures, presents the test data, includes an analysis of the data and provides recommendations regarding reliable relay testing

IEEE C37.105-1987: IEEE standard for qualifying Class 1E protective relays and auxiliaries for nuclear power generating stations

International Nuclear Information System (INIS)

Anon.

1992-01-01

This standard describes the basic principles, requirements, and methods for qualifying Class 1E protective relays and auxiliaries such as test and control switches, terminal blocks, and indicating lamps for applications in nuclear power generating stations. When properly employed it can be used to demonstrate the design adequacy of such equipment under normal, abnormal, design basis event and post design basis event conditions in accordance with ANSI/IEEE Std 323-1983. When protective relays and auxiliaries are located in areas not subject to harsh environments, environmental qualification is not required. Protective relays and auxiliaries located inside primary containment in a nuclear power generating station present special conditions beyond the scope of this document. The qualification procedure presented is generic in nature. Other methods may be used at the discretion of the qualifier, provided the basic precepts of ANSI/IEEE Std 32301983 are satisfied

CERN Relay Race

CERN Document Server

2006-01-01

The CERN relay race will take place around the Meyrin site on Wednesday 17 May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site.

Energy-efficient relay selection and optimal power allocation for performance-constrained dual-hop variable-gain AF relaying

KAUST Repository

Zafar, Ammar

2013-12-01

This paper investigates the energy-efficiency enhancement of a variable-gain dual-hop amplify-and-forward (AF) relay network utilizing selective relaying. The objective is to minimize the total consumed power while keeping the end-to-end signal-to-noise-ratio (SNR) above a certain peak value and satisfying the peak power constraints at the source and relay nodes. To achieve this objective, an optimal relay selection and power allocation strategy is derived by solving the power minimization problem. Numerical results show that the derived optimal strategy enhances the energy-efficiency as compared to a benchmark scheme in which both the source and the selected relay transmit at peak power. © 2013 IEEE.

SWIPT in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma

2017-02-09

In this paper, we consider a multiuser multiple- input multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting relays and multiple destinations. Since the end-to-end sum rate maximization problem is intractable, we tackle a simplified problem where we maximize the sum of the harvested energy at the relays, we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relay- destination channels. The interference mitigation at the destinations is managed in two ways: either to fix the interference covariance matrices at the destination and update them at each iteration until convergence, or to cancel the interference using an algorithm similar to the BD method. We provide numerical results to show the relevance of our proposed solution.

Relaying Strategies and Protocols for Efficient Wireless Networks

KAUST Repository

Zafar, Ammar

2014-10-01

Next generation wireless networks are expected to provide high data rate and satisfy the Quality-of-Service (QoS) constraints of the users. A significant component of achieving these goals is to increase the effi ciency of wireless networks by either optimizing current architectures or exploring new technologies which achieve that. The latter includes revisiting technologies which were previously proposed, but due to a multitude of reasons were ignored at that time. One such technology is relaying which was initially proposed in the latter half of the 1960s and then was revived in the early 2000s. In this dissertation, we study relaying in conjunction with resource allocation to increase the effi ciency of wireless networks. In this regard, we differentiate between conventional relaying and relaying with buffers. Conventional relaying is traditional relaying where the relay forwards the signal it received immediately. On the other hand, in relaying with buffers or buffer-aided relaying as it is called, the relay can store received data in its buffer and forward it later on. This gives the benefit of taking advantage of good channel conditions as the relay can only transmit when the channel conditions are good. The dissertation starts with conventional relaying and considers the problem of minimizing the total consumed power while maintaining system QoS. After upper bounding the system performance, more practical algorithms which require reduced feedback overhead are explored. Buffer-aided relaying is then considered and the joint user-and-hop scheduler is introduced which exploits multi-user diversity (MUD) and 5 multi-hop diversity (MHD) gains together in dual-hop broadcast channels. Next joint user-and-hop scheduling is extended to the shared relay channel where two source-destination pairs share a single relay. The benefits of buffer-aided relaying in the bidirectional relay channel utilizing network coding are then explored. Finally, a new transmission protocol

Spoiled Onions: Exposing Malicious Tor Exit Relays

OpenAIRE

Winter, Philipp; Lindskog, Stefan

2014-01-01

Several hundred Tor exit relays together push more than 1 GiB/s of network traffic. However, it is easy for exit relays to snoop and tamper with anonymised network traffic and as all relays are run by independent volunteers, not all of them are innocuous. In this paper, we seek to expose malicious exit relays and document their actions. First, we monitored the Tor network after developing a fast and modular exit relay scanner. We implemented several scanning modules for detecting common attac...

SWIPT in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma; Salem, Ahmed Sultan; Alouini, Mohamed-Slim

2017-01-01

In this paper, we consider a multiuser multiple- input multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting relays and multiple destinations. Since the end-to-end sum rate

Control circuit for transformer relay

International Nuclear Information System (INIS)

Wyatt, G.A.

1984-01-01

A control circuit for a transformer relay which will automatically momentarily control the transformer relay to a selected state upon energization of the control circuit. The control circuit has an energy storage element and a current director coupled in series and adapted to be coupled with the secondary winding of the transformer relay. A device for discharge is coupled across the energy storage element. The energy storage element and current director will momentarily allow a unidirectional flow of current in the secondary winding of the transformer relay upon application of energy to the control circuit. When energy is not applied to the control circuit the device for discharge will allow the energy storage element to discharge and be available for another operation of the control circuit

Improper Signaling for Virtual Full-Duplex Relay Systems

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim

2017-01-01

Virtual full-duplex (VFD) is a powerful solution to compensate the rate loss of half-duplex relaying without the need to full-duplex capable nodes. Inter-relay interference (IRI) challenges the operation of VFD relaying systems. Recently, improper signaling is employed at both relays of the VFD to mitigate the IRI by imposing the same signal characteristics for both relays. To further boost the achievable rate performance, asymmetric time sharing VFD relaying system is adopted with different improper signals at the half-duplex relays. The joint tuning of the three design parameters improves the achievable rate performance at different ranges of IRI and different relays locations. Extensive simulation results are presented and analyzed to show the achievable rate gain of the proposed system and understand the system behavior.

Improper Signaling for Virtual Full-Duplex Relay Systems

KAUST Repository

Gaafar, Mohamed

2017-02-14

Virtual full-duplex (VFD) is a powerful solution to compensate the rate loss of half-duplex relaying without the need to full-duplex capable nodes. Inter-relay interference (IRI) challenges the operation of VFD relaying systems. Recently, improper signaling is employed at both relays of the VFD to mitigate the IRI by imposing the same signal characteristics for both relays. To further boost the achievable rate performance, asymmetric time sharing VFD relaying system is adopted with different improper signals at the half-duplex relays. The joint tuning of the three design parameters improves the achievable rate performance at different ranges of IRI and different relays locations. Extensive simulation results are presented and analyzed to show the achievable rate gain of the proposed system and understand the system behavior.

Speech-to-Speech Relay Service

Science.gov (United States)

Consumer Guide Speech to Speech Relay Service Speech-to-Speech (STS) is one form of Telecommunications Relay Service (TRS). TRS is a service that allows persons with hearing and speech disabilities ...

Outage performance of two-way DF relaying systems with a new relay selection metric

KAUST Repository

Hyadi, Amal

2012-04-01

This paper investigates a new constrained relay selection scheme for two-way relaying systems where two end terminals communicate simultaneously via a relay. The introduced technique is based on the maximization of the weighted sum rate of both users. To evaluate the performance of the proposed system, the outage probability is derived in a general case (where an arbitrary channel is considered), and then over independently but not necessarily identically distributed (i.n.i.d.) Rayleigh fading channels. The analytical results are verified through simulations. © 2012 IEEE.

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond

KAUST Repository

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2016-01-01

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment. Copyright: © 2016 Nam et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond

KAUST Repository

Nam, Sung Sik

2016-11-29

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment. Copyright: © 2016 Nam et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Improper signaling in two-path relay channels

KAUST Repository

Gaafar, Mohamed

2017-07-03

Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.

Improper signaling in two-path relay channels

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim

2017-01-01

Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.

Relay self interference minimisation using tapped filter

KAUST Repository

Jazzar, Saleh

2013-05-01

In this paper we introduce a self interference (SI) estimation and minimisation technique for amplify and forward relays. Relays are used to help forward signals between a transmitter and a receiver. This helps increase the signal coverage and reduce the required transmitted signal power. One problem that faces relays communications is the leaked signal from the relay\\'s output to its input. This will cause an SI problem where the new received signal at the relay\\'s input will be added with the unwanted leaked signal from the relay\\'s output. A Solution is proposed in this paper to estimate and minimise this SI which is based upon using a tapped filter at the destination. To get the optimum weights for this tapped filter, some channel parameters must be estimated first. This is performed blindly at the destination without the need of any training. This channel parameter estimation method is named the blind-self-interference-channel-estimation (BSICE) method. The next step in the proposed solution is to estimate the tapped filter\\'s weights. This is performed by minimising the mean squared error (MSE) at the destination. This proposed method is named the MSE-Optimum Weight (MSE-OW) method. Simulation results are provided in this paper to verify the performance of BSICE and MSE-OW methods. © 2013 IEEE.

Dynamic Relaying in 3GPP LTE-Advanced Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Van Phan, Vinh; Redana, Simone

2009-01-01

Relaying is one of the proposed technologies for LTE-Advanced networks. In order to enable a flexible and reliable relaying support, the currently adopted architectural structure of LTE networks has to be modified. In this paper, we extend the LTE architecture to enable dynamic relaying, while...... maintaining backward compatibility with LTE Release 8 user equipments, and without limiting the flexibility and reliability expected from relaying.With dynamic relaying, relays can be associated with base stations on a need basis rather than in a fixed manner which is based only on initial radio planning....... Proposals are also given on how to further improve a relay enhanced LTE network by enabling multiple interfaces between the relay nodes and their controlling base stations, which can possibly be based on technologies different from LTE, so that load balancing can be realized. This load balancing can...

Performance limitations of relay neurons.

Directory of Open Access Journals (Sweden)

Rahul Agarwal

Full Text Available Relay cells are prevalent throughout sensory systems and receive two types of inputs: driving and modulating. The driving input contains receptive field properties that must be transmitted while the modulating input alters the specifics of transmission. For example, the visual thalamus contains relay neurons that receive driving inputs from the retina that encode a visual image, and modulating inputs from reticular activating system and layer 6 of visual cortex that control what aspects of the image will be relayed back to visual cortex for perception. What gets relayed depends on several factors such as attentional demands and a subject's goals. In this paper, we analyze a biophysical based model of a relay cell and use systems theoretic tools to construct analytic bounds on how well the cell transmits a driving input as a function of the neuron's electrophysiological properties, the modulating input, and the driving signal parameters. We assume that the modulating input belongs to a class of sinusoidal signals and that the driving input is an irregular train of pulses with inter-pulse intervals obeying an exponential distribution. Our analysis applies to any [Formula: see text] order model as long as the neuron does not spike without a driving input pulse and exhibits a refractory period. Our bounds on relay reliability contain performance obtained through simulation of a second and third order model, and suggest, for instance, that if the frequency of the modulating input increases or the DC offset decreases, then relay increases. Our analysis also shows, for the first time, how the biophysical properties of the neuron (e.g. ion channel dynamics define the oscillatory patterns needed in the modulating input for appropriately timed relay of sensory information. In our discussion, we describe how our bounds predict experimentally observed neural activity in the basal ganglia in (i health, (ii in Parkinson's disease (PD, and (iii in PD during

Modular relay control

OpenAIRE

Ivarsson, Mikael

2010-01-01

Enics Sweden AB, Västerås, is an electronics manufacturing services company with its main business in manufacturing electronics. Most, if not all, electronic devices that are manufactured are being widely tested before delivery to ensure proper functionality. Often during tests a large number of signals are measured by one to a few digital multimeters and are therefore controlled through relays. Relays are also used when applying stimuli with high currents or voltages to the unit under test. ...

On the achievable degrees of freedom of alternate MIMO relaying with multiple AF relays

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim; Park, Seongho; Ko, Youngchai

2012-01-01

In this paper, we consider a two-hop relaying network where one source, one destination, and multiple amplify-and-forward (AF) relays equipped with M antennas operate in a half-duplex mode. In order to compensate for the inherent loss of capacity

Non-enzymatic N -acetylation of Lysine Residues by AcetylCoA Often Occurs via a Proximal S -acetylated Thiol Intermediate Sensitive to Glyoxalase II

OpenAIRE

James, Andrew M.; Hoogewijs, Kurt; Logan, Angela; Hall, Andrew R.; Ding, Shujing; Fearnley, Ian M.; Murphy, Michael P.

2017-01-01

Summary: Acetyl coenzyme A (AcCoA), a key intermediate in mitochondrial metabolism, N-acetylates lysine residues, disrupting and, in some cases, regulating protein function. The mitochondrial lysine deacetylase Sirtuin 3 (Sirt3) reverses this modification with benefits reported in diabetes, obesity, and aging. We show that non-enzymatic lysine N-acetylation by AcCoA is greatly enhanced by initial acetylation of a cysteine residue, followed by SN-transfer of the acetyl moiety to a nearby lysin...

Novel multi-dimensional heteronuclear NMR techniques for the study of 13C-O-acetylated oligosaccharides: Expanding the dimensions for carbohydrate structures

Energy Technology Data Exchange (ETDEWEB)

Jones, David N.M. [University of Colorado Health Sciences Center, Departments of Pharmacology (United States); Bendiak, Brad [University of Colorado Health Sciences Center, Departments of Cellular and Structural Biology (United States)

1999-10-15

Complex carbohydrates have critical roles in a wide variety of biological processes. An understanding of the molecular mechanisms that underlie these processes is essential in the development of novel oligosaccharide-based therapeutic strategies. Unfortunately, obtaining detailed structural information for larger oligosaccharides (>10 residues) can be exceedingly difficult, especially where the amount of sample available is limited. Here we demonstrate the application of {sup 13} C O-acetylation in combination with novel NMR experiments to obtain much of the information required to characterize the primary structure of oligosaccharides. (H)C{sub Me}COH-HEHAHA and H(C{sub Me})COH-HEHAHA experiments are presented that use heteronuclear Hartmann-Hahn transfer to correlate the acetyl groups with sugar ring protons in peracetylated oligosaccharides. The in-phase, pure absorption nature of the correlation peaks in these experiments allows measurement of both chemical shifts and, importantly, {sup 1}H-{sup 1}H coupling constants that are used to define the stereochemistry of the sugar ring. The (HC{sub Me})COH and (HC{sub Me})COH-RELAY experiments provide additional methods for obtaining chemical shift assignments for larger oligosaccharides to define the sites of glycosidic linkages from the patterns of acetylation.

Iterative Relay Scheduling with Hybrid ARQ under Multiple User Equipment (Type II) Relay Environments

KAUST Repository

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2018-01-01

-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed IRS-HARQ aims to increase the achievable data rate by iteratively scheduling a relatively better UE relay closer to the end user in a probabilistic sense, provided that the relay-to-end user

Multiple relay selection for delay-limited applications

KAUST Repository

Alsharoa, Ahmad M.

2013-12-01

A multiple relay selection system model that implements the decode-and-forward mode is investigated. All communication nodes are assumed to be equipped by multiple antennas. Furthermore, lattices space-time coded multiple-input multiple-output half duplex channel is applied. The main goal is to increase the throughput of the system by selecting multiple number of relays. The selection criteria depends on the maximum decoding delay at relays where the system implements a decoding time-out algorithm at each relay. This leads to a significant saving in the overall system power consumptions and attempts to solve the relays synchronization problem. All results are presented using numerical simulations. © 2012 IEEE.

Dynamic Relaying in 3GPP LTE-Advanced Networks

Directory of Open Access Journals (Sweden)

Van Phan Vinh

2009-01-01

Full Text Available Relaying is one of the proposed technologies for LTE-Advanced networks. In order to enable a flexible and reliable relaying support, the currently adopted architectural structure of LTE networks has to be modified. In this paper, we extend the LTE architecture to enable dynamic relaying, while maintaining backward compatibility with LTE Release 8 user equipments, and without limiting the flexibility and reliability expected from relaying. With dynamic relaying, relays can be associated with base stations on a need basis rather than in a fixed manner which is based only on initial radio planning. Proposals are also given on how to further improve a relay enhanced LTE network by enabling multiple interfaces between the relay nodes and their controlling base stations, which can possibly be based on technologies different from LTE, so that load balancing can be realized. This load balancing can be either between different base stations or even between different networks.

Airborne relay-based regional positioning system.

Science.gov (United States)

Lee, Kyuman; Noh, Hongjun; Lim, Jaesung

2015-05-28

Ground-based pseudolite systems have some limitations, such as low vertical accuracy, multipath effects and near-far problems. These problems are not significant in airborne-based pseudolite systems. However, the monitoring of pseudolite positions is required because of the mobility of the platforms on which the pseudolites are mounted, and this causes performance degradation. To address these pseudolite system limitations, we propose an airborne relay-based regional positioning system that consists of a master station, reference stations, airborne relays and a user. In the proposed system, navigation signals are generated from the reference stations located on the ground and are relayed via the airborne relays. Unlike in conventional airborne-based systems, the user in the proposed system sequentially estimates both the locations of airborne relays and his/her own position. Therefore, a delay due to monitoring does not occur, and the accuracy is not affected by the movement of airborne relays. We conducted several simulations to evaluate the performance of the proposed system. Based on the simulation results, we demonstrated that the proposed system guarantees a higher accuracy than airborne-based pseudolite systems, and it is feasible despite the existence of clock offsets among reference stations.

Acetylation/deacetylation reactions of T-2, acetyl T-2, HT-2, and acetyl HT-2 toxins in bovine rumen fluid in vitro

International Nuclear Information System (INIS)

Munger, C.E.; Ivie, G.W.; Christopher, R.J.; Hammock, B.D.; Phillips, T.D.

1987-01-01

A tritiated preparation of the trichothecene mycotoxin, T-2 toxin, underwent both acetylation and deacetylation reactions when incubated with bovine rumen fluid in vitro. Products from incubations of T-2 in rumen fluid included acetyl T-2, HT-2, and acetyl HT-2. Direct studies with tritiated samples of each of these metabolites confirmed their relatively facile interconversion in the rumen. Studies with [ 3 H]HT-2 under conditions of inhibited esterase activity (added diisopropyl fluorophosphate) showed that acetylation is preferred at C-3 vs. C-4. Studies with [ 3 H]acetyl T-2 indicated that deacetylation similarly occurs with greater rapidity at C-3. There were no indications that ester hydrolysis of these trichothecenes occurred at C-8 or C-15 or that they were subjected to epoxide reduction reactions. These data suggest that acetylation of T-2 and other trichothecenes in the rumen in situ may ultimately result in the absorption of more lipophilic metabolites whose toxicological and residual properties are at present unknown

Bilayer expurgated LDPC codes with uncoded relaying

Directory of Open Access Journals (Sweden)

Md. Noor-A-Rahim

2017-08-01

Full Text Available Bilayer low-density parity-check (LDPC codes are an effective coding technique for decode-and-forward relaying, where the relay forwards extra parity bits to help the destination to decode the source bits correctly. In the existing bilayer coding scheme, these parity bits are protected by an error correcting code and assumed reliably available at the receiver. We propose an uncoded relaying scheme, where the extra parity bits are forwarded to the destination without any protection. Through density evolution analysis and simulation results, we show that our proposed scheme achieves better performance in terms of bit erasure probability than the existing relaying scheme. In addition, our proposed scheme results in lower complexity at the relay.

A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

KAUST Repository

Rao, Anlei

2015-09-11

Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (QoS) requirements. For the later type design, previous works has worked on minimizing the approximated power consumption. In this paper, exact power consumption for all relays is derived into a quadratic form by diagonalizing the minimum-square error (MSE) matrix, and the relay precoding matrix is designed by optimizing this quadratic form with the help of semidefinite programming (SDP) relaxation. Our simulation results show that such a design can achieve a gain of around 3 dB against the previous design, which optimized the approximated power consumption. © 2015 IEEE.

Opportunistic Relay Selection with Cooperative Macro Diversity

Directory of Open Access Journals (Sweden)

Yu Chia-Hao

2010-01-01

Full Text Available We apply a fully opportunistic relay selection scheme to study cooperative diversity in a semianalytical manner. In our framework, idle Mobile Stations (MSs are capable of being used as Relay Stations (RSs and no relaying is required if the direct path is strong. Our relay selection scheme is fully selection based: either the direct path or one of the relaying paths is selected. Macro diversity, which is often ignored in analytical works, is taken into account together with micro diversity by using a complete channel model that includes both shadow fading and fast fading effects. The stochastic geometry of the network is taken into account by having a random number of randomly located MSs. The outage probability analysis of the selection differs from the case where only fast fading is considered. Under our framework, distribution of the received power is formulated using different Channel State Information (CSI assumptions to simulate both optimistic and practical environments. The results show that the relay selection gain can be significant given a suitable amount of candidate RSs. Also, while relay selection according to incomplete CSI is diversity suboptimal compared to relay selection based on full CSI, the loss in average throughput is not too significant. This is a consequence of the dominance of geometry over fast fading.

Opportunistic Fixed Gain Bidirectional Relaying with Outdated CSI

KAUST Repository

Khan, Fahd Ahmed; Tourki, Kamel; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

2015-01-01

In a network with multiple relays, relay selection has been shown as an effective scheme to achieve diversity as well as to improve the overall throughput. This paper studies the impact of using outdated channel state information for relay selection on the performance of a network where two sources communicate with each other via fixed-gain amplify-and-forward relays. For a Rayleigh faded channel, closed-form expressions for the outage probability, moment generating function and symbol error rate are derived. Simulations results are also presented to corroborate the derived analytical results. It is shown that adding relays does not improve the performance if the channel is substantially outdated. Furthermore, relay location is also taken into consideration and it is shown that the performance can be improved by placing the relay closer to the source whose channel is more outdated. © 2015 IEEE.

Opportunistic Fixed Gain Bidirectional Relaying with Outdated CSI

KAUST Repository

Khan, Fahd Ahmed

2015-05-01

In a network with multiple relays, relay selection has been shown as an effective scheme to achieve diversity as well as to improve the overall throughput. This paper studies the impact of using outdated channel state information for relay selection on the performance of a network where two sources communicate with each other via fixed-gain amplify-and-forward relays. For a Rayleigh faded channel, closed-form expressions for the outage probability, moment generating function and symbol error rate are derived. Simulations results are also presented to corroborate the derived analytical results. It is shown that adding relays does not improve the performance if the channel is substantially outdated. Furthermore, relay location is also taken into consideration and it is shown that the performance can be improved by placing the relay closer to the source whose channel is more outdated. © 2015 IEEE.

MaROS Strategic Relay Planning and Coordination Interfaces

Science.gov (United States)

Allard, Daniel A.

2010-01-01

The Mars Relay Operations Service (MaROS) is designed to provide planning and analysis tools in support of ongoing Mars Network relay operations. Strategic relay planning requires coordination between lander and orbiter mission ground data system (GDS) teams to schedule and execute relay communications passes. MaROS centralizes this process, correlating all data relevant to relay coordination to provide a cohesive picture of the relay state. Service users interact with the system through thin-layer command line and web user interface client applications. Users provide and utilize data such as lander view periods of orbiters, Deep Space Network (DSN) antenna tracks, and reports of relay pass performance. Users upload and download relevant relay data via formally defined and documented file structures including some described in Extensible Markup Language (XML). Clients interface with the system via an http-based Representational State Transfer (ReST) pattern using Javascript Object Notation (JSON) formats. This paper will provide a general overview of the service architecture and detail the software interfaces and considerations for interface design.

Production of Nα-acetyl Tα1-HSA through in vitro acetylation by RimJ.

Science.gov (United States)

Chen, Jing; Li, Haibin; Wang, Tao; Sun, Shuyang; Liu, Jia; Chen, Jianhua

2017-11-10

Thymosin alpha 1 (Tα1) is an important immunomodulating agent with various clinical applications. The natural form of Tα1 is N α -acetylated, which was supposed to be related to in vivo stability of the hormone. In this study, fusion protein Tα1-HSA was constructed and expressed in Pichia pastoris . RimJ, a N α -acetyltransferase from E.coli , was also overexpressed and purified to homogeneity. In vitro acetylation of Tα1-HSA in the presence of RimJ and acetyl coenzyme A resulted in N α -acetyl Tα1-HSA. The N α -acetylation was determined by LC-MS/MS. Kinetic assay indicated that RimJ had a higher affinity to desacetyl Tα1 than to Tα1-HSA. Bioactivity assay revealed fully retained activity of Tα1 when the hormone was connected to the N-terminus of the fusion protein, while the activity was compromised in our previously constructed HSA-Tα1. With fully retained activity and N-terminal acetylation, N α -acetyl Tα1-HSA was expected to be a more promising pharmaceutical agent than Tα1.

Relay selection from an effective capacity perspective

KAUST Repository

Yang, Yuli

2013-09-01

In this work, we consider a cooperative network where multiple relay nodes having different modulation capabilities assist the end-to-end communication between a source and its destination. Firstly, we evaluate the effective capacity (EC) performance of the network under study. According to the analysis, an EC-based relay selection criterion is proposed. Based on the proposed selection rule and half-duplex decode-and-forward protocol, the activated relays cooperatively help with the packet transmission from the source. At the destination, packet combining is taken into account to improve the quality of service. Compared to the popular scheme, opportunistic relay selection, numerical results are provided to prove the validity and advantages of our proposed scheme in certain scenarios. Moreover, the analysis presented herein offers a convenient tool to the relaying transmission design, specifically on which relay selection scheme should be used as well as how to choose the receiving strategy between with and without packet combining at the destination. © 2013 IEEE.

CERN Relay Race 2009

CERN Document Server

2009-01-01

The CERN relay race will take place around the Meyrin site on Thursday 14th May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. More details on how to register your team for the relay race

Reversal thyristor-relay direct current commutator

International Nuclear Information System (INIS)

Ivanenko, A.I.

1982-01-01

A thyristor-relay commutator used for alteration of the leading magnetic field direction in experiments with polarized neutrons is described. The commutator flowsheet is presented. Thyristors, connected so as to allow the relay trigger operation mode, are used as controllable electronic relay. Two connected in series coils with the total inductance of the order of 0.28 H serve as the electronic relay load. The arc-free current commutation is effected at the moment of the minimal current across the load terminals, which allows to easily reverse the current up to 10 A at a volatage, v <= 150 V. The experience gained within a year of operation has shown that the commutator meets the requirements of reliability and tuning

CERN Relay Race

CERN Multimedia

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19 May starting at 12-15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details of the course and of how to register your team for the relay race can be found here. Some advice for all runners from the Medical Service can also be found here.   

Protection relay of phase-shifting device with thyristor switch for high voltage power transmission lines

Science.gov (United States)

Lachugin, V. F.; Panfilov, D. I.; Akhmetov, I. M.; Astashev, M. G.; Shevelev, A. V.

2014-12-01

Problems of functioning of differential current protection systems of phase shifting devices (PSD) with mechanically changed coefficient of transformation of shunt transformer are analyzed. Requirements for devices of protection of PSD with thyristor switch are formulated. Based on use of nonlinear models of series-wound and shunt transformers of PSD modes of operation of major protection during PSD, switching to zero load operation and to operation under load and during short circuit operation were studied for testing PSD with failures. Use of the principle of duplicating by devices of differential current protection (with realization of functions of breaking) of failures of separate pares of PSD with thyristor switch was substantiated. To ensure protection sensitivity to the shunt transformer winding short circuit, in particular, to a short circuit that is not implemented in the current differential protection for PSD with mechanical switch, the differential current protection reacting to the amount of primary ampere-turns of high-voltage and low-voltage winding of this transformer was designed. Studies have shown that the use of differential current cutoff instead of overcurrent protection for the shunt transformer wndings allows one to provide the sensitivity during thyristor failure with the formation of a short circuit. The results of simulation mode for the PSD with switch thyristor designed to be installed as switching point of Voskhod-Tatarskaya-Barabinsk 220 kV transmission line point out the efficiency of the developed solutions that ensure reliable functioning of the PSD.

A low complexity algorithm for multiple relay selection in two-way relaying Cognitive Radio networks

KAUST Repository

Alsharoa, Ahmad M.

2013-06-01

In this paper, a multiple relay selection scheme for two-way relaying cognitive radio network is investigated. We consider a cooperative Cognitive Radio (CR) system with spectrum sharing scenario using Amplify-and-Forward (AF) protocol, where licensed users and unlicensed users operate on the same frequency band. The main objective is to maximize the sum rate of the unlicensed users allowed to share the spectrum with the licensed users by respecting a tolerated interference threshold. A practical low complexity heuristic approach is proposed to solve our formulated optimization problem. Selected numerical results show that the proposed algorithm reaches a performance close to the performance of the optimal multiple relay selection scheme either with discrete or continuous power distributions while providing a considerable saving in terms of computational complexity. In addition, these results show that our proposed scheme significantly outperforms the single relay selection scheme. © 2013 IEEE.

Analysis of errors of radiation relay, (1)

International Nuclear Information System (INIS)

Koyanagi, Takami; Nakajima, Sinichi

1976-01-01

The statistical error of liquid level controlled by radiation relay is analysed and a method of minimizing the error is proposed. This method comes to the problem of optimum setting of the time constant of radiation relay. The equations for obtaining the value of time constant are presented and the numerical results are shown in a table and plotted in a figure. The optimum time constant of the upper level control relay is entirely different from that of the lower level control relay. (auth.)

Micro optical fiber display switch based on the magnetohydrodynamic (MHD) principle

Science.gov (United States)

Lian, Kun; Heng, Khee-Hang

2001-09-01

This paper reports on a research effort to design, microfabricate and test an optical fiber display switch based on magneto hydrodynamic (MHD) principal. The switch is driven by the Lorentz force and can be used to turn on/off the light. The SU-8 photoresist and UV light source were used for prototype fabrication in order to lower the cost. With a magnetic field supplied by an external permanent magnet, and a plus electrical current supplied across the two inert sidewall electrodes, the distributed body force generated will produce a pressure difference on the fluid mercury in the switch chamber. By change the direction of current flow, the mercury can turn on or cut off the light pass in less than 10 ms. The major advantages of a MHD-based micro-switch are that it does not contain any solid moving parts and power consumption is much smaller comparing to the relay type switches. This switch can be manufactured by molding gin batch production and may have potential applications in extremely bright traffic control,, high intensity advertising display, and communication.

Mapping sugar beet pectin acetylation pattern.

Science.gov (United States)

Ralet, Marie-Christine; Cabrera, Juan Carlos; Bonnin, Estelle; Quéméner, Bernard; Hellìn, Pilar; Thibault, Jean-François

2005-08-01

Homogalacturonan-derived partly methylated and/or acetylated oligogalacturonates were recovered after enzymatic hydrolysis (endo-polygalacturonase+pectin methyl esterase+side-chain degrading enzymes) of sugar beet pectin followed by anion-exchange and size exclusion chromatography. Around 90% of the GalA and 75% of the acetyl groups present in the initial sugar beet pectin were recovered as homogalacturonan-derived oligogalacturonates, the remaining GalA and acetyl belonging to rhamnogalacturonic regions. Around 50% of the acetyl groups present in sugar beet homogalacturonans were recovered as partly methylated and/or acetylated oligogalacturonates of degree of polymerisation 5 whose structures were determined by electrospray ionization ion trap mass spectrometry (ESI-IT-MSn). 2-O-acetyl- and 3-O-acetyl-GalA were detected in roughly similar amounts but 2,3-di-O-acetylation was absent. Methyl-esterified GalA residues occurred mainly upstream 2-O-acetyl GalA. Oligogalacturonates containing GalA residues that are at once methyl- and acetyl-esterified were recovered in very limited amounts. A tentative mapping of the distribution of acetyl and methyl esters within sugar beet homogalacturonans is proposed. Unsubstituted GalA residues are likely to be present in limited amounts (approximately 10% of total GalA residues), due to the fact that methyl and acetyl groups are assumed to be most often not carried by the same residues.

49 CFR 236.52 - Relayed cut-section.

Science.gov (United States)

2010-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Rules and Instructions: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... 49 Transportation 4 2010-10-01 2010-10-01 false Relayed cut-section. 236.52 Section 236.52...

Quantum cryptography with an ideal local relay

DEFF Research Database (Denmark)

Spedalieri, Gaetana; Ottaviani, Carlo; Braunstein, Samuel L.

2015-01-01

We consider two remote parties connected to a relay by two quantum channels. To generate a secret key, they transmit coherent states to the relay, where the states are subject to a continuous-variable (CV) Bell detection. We study the ideal case where Alice's channel is lossless, i.e., the relay ...

A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

KAUST Repository

Rao, Anlei; Park, Kihong; Alouini, Mohamed-Slim

2015-01-01

Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (Qo

Acetylation/deacetylation reactions of T-2, acetyl T-2, HT-2, and acetyl HT-2 toxins in bovine rumen fluid in vitro

Energy Technology Data Exchange (ETDEWEB)

Munger, C.E.; Ivie, G.W.; Christopher, R.J.; Hammock, B.D.; Phillips, T.D.

A tritiated preparation of the trichothecene mycotoxin, T-2 toxin, underwent both acetylation and deacetylation reactions when incubated with bovine rumen fluid in vitro. Products from incubations of T-2 in rumen fluid included acetyl T-2, HT-2, and acetyl HT-2. Direct studies with tritiated samples of each of these metabolites confirmed their relatively facile interconversion in the rumen. Studies with (/sup 3/H)HT-2 under conditions of inhibited esterase activity (added diisopropyl fluorophosphate) showed that acetylation is preferred at C-3 vs. C-4. Studies with (/sup 3/H)acetyl T-2 indicated that deacetylation similarly occurs with greater rapidity at C-3. There were no indications that ester hydrolysis of these trichothecenes occurred at C-8 or C-15 or that they were subjected to epoxide reduction reactions. These data suggest that acetylation of T-2 and other trichothecenes in the rumen in situ may ultimately result in the absorption of more lipophilic metabolites whose toxicological and residual properties are at present unknown.

User Multiplexing in Relay Enhanced LTE-Advanced Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Frederiksen, Frank; Redana, Simone

2010-01-01

is radio relaying. This uses relay nodes that act as surrogate base stations for mobile users whose radio links with the base stations are not experiencing good enough conditions. In the downlink, the data that is destined for the relayed users may first have to be multiplexed by the base station, sent...... over the wireless backhaul link towards the relay node, and de-multiplexed and forwarded to the individual users by the relay node. The reverse process also has to be undertaken in the uplink. In this paper, we present a novel multiplexing scheme which is able to adapt the addressing and bitmapping...... of user identification to the actual number of users being served by the relay nodes, and thus greatly reduce the multiplexing overhead....

Amplify-and-forward relaying in wireless communications

CERN Document Server

Rodriguez, Leonardo Jimenez; Le-Ngoc, Tho

2015-01-01

This SpringerBrief explores the advantage of relaying techniques in addressing the increasing demand for high data rates and reliable services over the air. It demonstrates how to design cost-effective relay systems that provide high spectral efficiency and fully exploit the diversity of the relay channel. The brief covers advances in achievable rates, power allocation schemes, and error performance for half-duplex (HD) and full-duplex (FD) amplify-and-forward (AF) single-relay systems. The authors discuss the capacity and respective optimal power allocation for a wide range of HD protocols ov

High voltage disconnect switch position monitoring

Energy Technology Data Exchange (ETDEWEB)

Crampton, S W

1983-08-01

Unreliable position indication on high-voltage (HV) disconnect switches can result in equipment damage worth many times the cost of a disconnect switch. The benefits and limitations of a number of possible methods of reliably monitoring HV disconnect switches are assessed. Several methods of powering active devices at HV are noted. It is concluded that the most reliable way of monitoring switch position at reasonable cost would use a passive hermetically-sealed blade-position sensor located at HV, with a fibre-optic link between HV and ground. Separate sensors would be used for open and closed position indication. For maximum reliability the fibre-optic link would continue into the relay building. A passive magnetically actuated fibre-optic sensor has been built which demonstrates the feasibility of the concept. The sensor monitors blade position relative to the jaws in three dimensions with high resolution. A design for an improved passive magneto-optic sensor has significantly lower optical losses, allowing a single fibre-optic loop and 3 sensors to monitor closure of all phases of a disconnect switch. A similar loop would monitor switch opening. The improved sensor has a solid copper housing to provide greater immunity to fault currents, and to protect it from the environment and from physical damage. Two methods of providing a protected path for fibre-optics passing from HV to ground are proposed, one using a hollow porcelain switch-support insulator and the other using an additional small-diameter polymer insulator with optical fibres imbedded in its fibreglass core. A number of improvements are recommended which can be made to existing switches to increase their reliability. 16 refs., 13 figs., 1 tab.

Full-Duplex Relay Selection in Cognitive Underlay Networks

KAUST Repository

Khafagy, Mohammad Galal

2017-09-30

In this work, we analyze the performance of full-duplex relay selection (FDRS) in spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay(s), thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint, which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic FDRS with residual self-interference (RSI) by deriving the exact cumulative distribution function of its end-to-end signal-to-interference-plus-noise ratio under Nakagami-m fading. We also evaluate the offered diversity gain of relay selection for different full-duplex cooperation schemes in the presence/absence of a direct source-destination link. When the adopted RSI link gain model is sublinear in the relay power, which agrees with recent research findings, we show that remarkable diversity gain can be recovered even in the presence of an interfering direct link. Second, we evaluate the end-to-end performance of FDRS with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

Relay exchanges in elite short track speed skating.

Science.gov (United States)

Hext, Andrew; Heller, Ben; Kelley, John; Goodwill, Simon

2017-06-01

In short track speed skating, the relay exchange provides an additional strategic component to races by allowing a team to change the skater involved in the pack race. Typically executed every 1½ laps, it is the belief of skaters and coaches that during this period of the race, time can be gained or lost due to the execution of the relay exchange. As such, the aim of this study was to examine the influence of the relay exchange on a team's progression through a 5000 m relay race. Using data collected from three World Cup relay events during the 2012-2013 season, the time taken to complete the straight for the scenarios with and without the relay exchange were compared at different skating speeds for the corner exit prior to the straight. Overall, the influence of the relay exchange was found to be dependent on this corner exit speed. At slower corner exit speeds (12.01-13.5 m/s), relay exchange straight times were significantly faster than the free skating scenario (P < 0.01). While at faster corner exit speeds (14.01-15 m/s), straight times were significantly slower (P < 0.001). The findings of this study suggest that the current norm of executing relay exchanges every 1½ laps may not be optimal. Instead, varying the frequency of relay exchange execution throughout the race could allow: (1) time to be gained relative to other teams; and (2) facilitate other race strategies by providing an improved opportunity to overtake.

On Alternate Relaying with Improper Gaussian Signaling

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Ikhlef, Aissa; Chaaban, Anas; Alouini, Mohamed-Slim

2016-01-01

In this letter, we investigate the potential benefits of adopting improper Gaussian signaling (IGS) in a two-hop alternate relaying (AR) system. Given the known benefits of using IGS in interference-limited networks, we propose to use IGS to relieve the inter-relay interference (IRI) impact on the AR system assuming no channel state information is available at the source. In this regard, we assume that the two relays use IGS and the source uses proper Gaussian signaling (PGS). Then, we optimize the degree of impropriety of the relays signal, measured by the circularity coefficient, to maximize the total achievable rate. Simulation results show that using IGS yields a significant performance improvement over PGS, especially when the first hop is a bottleneck due to weak source-relay channel gains and/or strong IRI.

On Alternate Relaying with Improper Gaussian Signaling

KAUST Repository

Gaafar, Mohamed

2016-06-06

In this letter, we investigate the potential benefits of adopting improper Gaussian signaling (IGS) in a two-hop alternate relaying (AR) system. Given the known benefits of using IGS in interference-limited networks, we propose to use IGS to relieve the inter-relay interference (IRI) impact on the AR system assuming no channel state information is available at the source. In this regard, we assume that the two relays use IGS and the source uses proper Gaussian signaling (PGS). Then, we optimize the degree of impropriety of the relays signal, measured by the circularity coefficient, to maximize the total achievable rate. Simulation results show that using IGS yields a significant performance improvement over PGS, especially when the first hop is a bottleneck due to weak source-relay channel gains and/or strong IRI.

An assessment of fire vulnerability for aged electrical relays

International Nuclear Information System (INIS)

Vigil, R.A.; Nowlen, S.P.

1995-03-01

There has been some concern that, as nuclear power plants age, protective measures taken to control and minimize the impact of fire may become ineffective, or significantly less effective, and hence result in an increased fire risk. One objective of the Fire Vulnerability of Aged Electrical Components Program is to assess the effects of aging and service wear on the fire vulnerability of electrical equipment. An increased fire vulnerability of components may lead to an overall increase in fire risk to the plant. Because of their widespread use in various electrical safety systems, electromechanical relays were chosen to be the initial components for evaluation. This test program assessed the impact of operational and thermal aging on the vulnerability of these relays to fire-induced damage. Only thermal effects of a fire were examined in this test program. The impact of smoke, corrosive materials, or fire suppression effects on relay performance were not addressed in this test program. The purpose of this test program was to assess whether the fire vulnerability of electrical relays increased with aging. The sequence followed for the test program was to: identify specific relay types, develop three fire scenarios, artificially age several relays, test the unaged and aged relays in the fire exposure scenarios, and compare the results. The relays tested were Agastat GPI, General Electric (GE) HMA, HGA, and HFA. At least two relays of each type were artificially aged and at least two relays of each type were new. Relays were operationally aged by cycling the relay under rated load for 2,000 operations. These relays were then thermally aged for 60 days with their coil energized

Microprocessor protection relays: new prospects or new problems?

OpenAIRE

Gurevich, Vladimir

2006-01-01

The internal architecture and principles of operation of microprocessor-based devices including so-called "microprocessor protective relays" have little in common with devices called "electric relays". But microprocessor-based relay protection devices are gradually driving out the traditional electromechanical and even electronic relay protection of virtually from all fields of power and electrical engineering. Advantages of microprocessor-based protection means over traditional ones are far ...

Cognitive Relay Networks: A Comprehensive Survey

Directory of Open Access Journals (Sweden)

Ayesha Naeem

2015-07-01

Full Text Available Cognitive radio is an emerging technology to deal with the scarcity and requirement of radio spectrum by dynamically assigning spectrum to unlicensed user . This revolutionary technology shifts the paradigm in the wireless system design by all owing unlicensed user the ability to sense, adapt and share the dynamic spectrum. Cognitive radio technology have been applied to different networks and applications ranging from wireless to public saf ety, smart grid, medical, rela y and cellular applications to increase the throughput and spectrum efficiency of the network. Among these applications, cognitive relay networks is one of the application where cognitive radio technology has been applied. Cognitiv e rela y network increases the network throughput by reducing the complete pa th loss and also by ensuring cooper ation among secondary users and cooperation among primary and secondary users. In this paper , our aim is to provide a survey on cognitive relay network. We also provide a detailed review on existing schemes in cognitive relay networks on the basis of relaying protocol, relay cooperation and channel model.

Error-rate performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2011-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path can

Experimental evaluation of earthquake induced relay chattering

International Nuclear Information System (INIS)

Bandyopadhyay, K.; Hofmayer, C.; Shteyngart, S.

1990-01-01

An experimental evaluation of relay performance under vibratory environments is discussed in this paper. Single frequency excitation was used for most tests. Limited tests were performed with random multifrequency inputs. The capacity of each relay was established based on a two-millisecond chatter criterion. The experimental techniques are described and the effects of parameters in controlling the relay capacity levels are illustrated with test data. A wide variation of the capacity levels was observed due to the influence of parameters related to the design of the relay and nature of the input motion. 3 refs., 15 figs

Relay protection features of frequency-adjustable electric drive

Science.gov (United States)

Kuprienko, V. V.

2018-03-01

The features of relay protection of high-voltage electric motors in composition of the frequency-adjustable electric drive are considered in the article. The influence of frequency converters on the stability of the operation of various types of relay protection used on electric motors is noted. Variants of circuits for connecting relay protection devices are suggested. The need to develop special relay protection devices for a frequency-adjustable electric drive is substantiated.

Relay Telecommunications for the Coming Decade of Mars Exploration

Science.gov (United States)

Edwards, C.; DePaula, R.

2010-01-01

Over the past decade, an evolving network of relay-equipped orbiters has advanced our capabilities for Mars exploration. NASA's Mars Global Surveyor, 2001 Mars Odyssey, and Mars Reconnaissance Orbiter (MRO), as well as ESA's Mars Express Orbiter, have provided telecommunications relay services to the 2003 Mars Exploration Rovers, Spirit and Opportunity, and to the 2007 Phoenix Lander. Based on these successes, a roadmap for continued Mars relay services is in place for the coming decade. MRO and Odyssey will provide key relay support to the 2011 Mars Science Laboratory (MSL) mission, including capture of critical event telemetry during entry, descent, and landing, as well as support for command and telemetry during surface operations, utilizing new capabilities of the Electra relay payload on MRO and the Electra-Lite payload on MSL to allow significant increase in data return relative to earlier missions. Over the remainder of the decade a number of additional orbiter and lander missions are planned, representing new orbital relay service providers and new landed relay users. In this paper we will outline this Mars relay roadmap, quantifying relay performance over time, illustrating planned support scenarios, and identifying key challenges and technology infusion opportunities.

Evaluation of Harmonics Impact on Digital Relays

Directory of Open Access Journals (Sweden)

Kinan Wannous

2018-04-01

Full Text Available This paper presents the concept of the impact of harmonic distortion on a digital protection relay. The aim is to verify and determine the reasons of a mal-trip or failure to trip the protection relays; the suggested solution of the harmonic distortion is explained by a mathematical model in the Matlab Simulink programming environment. The digital relays have been tested under harmonic distortions in order to verify the function of the relays algorithm under abnormal conditions. The comparison between the protection relay algorithm under abnormal conditions and a mathematical model in the Matlab Simulink programming environment based on injected harmonics of high values is provided. The test is separated into different levels; the first level is based on the harmonic effect of an individual harmonic and mixed harmonics. The test includes the effect of the harmonics in the location of the fault point into distance protection zones. This paper is a new proposal in the signal processing of power quality disturbances using Matlab Simulink and the power quality impact on the measurements of the power system quantities; the test simulates the function of protection in power systems in terms of calculating the current and voltage values of short circuits and their faults. The paper includes several tests: frequency variations and decomposition of voltage waveforms with Fourier transforms (model and commercial relay, the effect of the power factor on the location of fault points, the relation between the tripping time and the total harmonic distortion (THD levels in a commercial relay, and a comparison of the THD capture between the commercial relay and the model.

Relay testing parametric investigation of seismic fragility

International Nuclear Information System (INIS)

Bandyopadhyay, K.; Hofmayer, C.; Kassir, M.; Pepper, S.

1989-01-01

The seismic capacity of most electrical equipment is governed by malfunction of relays. An evaluation of the existing relay test data base at Brookhaven National Laboratory (BNL) has indicated that the seismic fragility of a relay may depend on various parameters related to the design or the input motion. In particular, the electrical mode, contact state, adjustment, chatter duration acceptance limit, and the frequency and the direction of the vibration input have been considered to influence the relay fragility level. For a particular relay type, the dynamics of its moving parts depends on the exact model number and vintage and hence, these parameters may also influence the fragility level. In order to investigate the effect of most of these parameters on the seismic fragility level, BNL has conducted a relay test program. The testing has been performed at Wyle Laboratories. Establishing the correlation between the single frequency fragility test input and the corresponding multifrequency response spectrum (TRS) is also an objective of this test program. This paper discusses the methodology used for testing and presents a brief summary of important test results. 1 ref., 10 figs

Capacity Bounds and Mapping Design for Binary Symmetric Relay Channels

Directory of Open Access Journals (Sweden)

Majid Nasiri Khormuji

2012-12-01

Full Text Available Capacity bounds for a three-node binary symmetric relay channel with orthogonal components at the destination are studied. The cut-set upper bound and the rates achievable using decode-and-forward (DF, partial DF and compress-and-forward (CF relaying are first evaluated. Then relaying strategies with finite memory-length are considered. An efficient algorithm for optimizing the relay functions is presented. The Boolean Fourier transform is then employed to unveil the structure of the optimized mappings. Interestingly, the optimized relay functions exhibit a simple structure. Numerical results illustrate that the rates achieved using the optimized low-dimensional functions are either comparable to those achieved by CF or superior to those achieved by DF relaying. In particular, the optimized low-dimensional relaying scheme can improve on DF relaying when the quality of the source-relay link is worse than or comparable to that of other links.

Duplex Schemes in Multiple Antenna Two-Hop Relaying

Directory of Open Access Journals (Sweden)

Anja Klein

2008-04-01

Full Text Available A novel scheme for two-hop relaying defined as space division duplex (SDD relaying is proposed. In SDD relaying, multiple antenna beamforming techniques are applied at the intermediate relay station (RS in order to separate downlink and uplink signals of a bi-directional two-hop communication between two nodes, namely, S1 and S2. For conventional amplify-and-forward two-hop relaying, there appears a loss in spectral efficiency due to the fact that the RS cannot receive and transmit simultaneously on the same channel resource. In SDD relaying, this loss in spectral efficiency is circumvented by giving up the strict separation of downlink and uplink signals by either time division duplex or frequency division duplex. Two novel concepts for the derivation of the linear beamforming filters at the RS are proposed; they can be designed either by a three-step or a one-step concept. In SDD relaying, receive signals at S1 are interfered by transmit signals of S1, and receive signals at S2 are interfered by transmit signals of S2. An efficient method in order to combat this kind of interference is proposed in this paper. Furthermore, it is shown how the overall spectral efficiency of SDD relaying can be improved if the channels from S1 and S2 to the RS have different qualities.

Two-Hop Secure Communication Using an Untrusted Relay

Directory of Open Access Journals (Sweden)

Xiang He

2009-01-01

Full Text Available We consider a source-destination pair that can only communicate through an untrusted intermediate relay node. The intermediate node is willing to employ a designated relaying scheme to facilitate reliable communication between the source and the destination. Yet, the information it relays needs to be kept secret from it. In this two-hop communication scenario, where the use of the untrusted relay node is essential, we find that a positive secrecy rate is achievable. The center piece of the achievability scheme is the help provided by either the destination node with transmission capability, or an external “good samaritan” node. In either case, the helper performs cooperative jamming that confuses the eavesdropping relay and disables it from being able to decipher what it is relaying. We next derive an upper bound on the secrecy rate for this system. We observe that the gap between the upper bound and the achievable rate vanishes as the power of the relay node goes to infinity. Overall, the paper presents a case for intentional interference, that is, cooperative jamming, as an enabler for secure communication.

Energy-efficient relay selection and optimal power allocation for performance-constrained dual-hop variable-gain AF relaying

KAUST Repository

Zafar, Ammar; Radaydeh, Redha Mahmoud Mesleh; Chen, Yunfei; Alouini, Mohamed-Slim

2013-01-01

This paper investigates the energy-efficiency enhancement of a variable-gain dual-hop amplify-and-forward (AF) relay network utilizing selective relaying. The objective is to minimize the total consumed power while keeping the end-to-end signal

Application of a proposed overcurrent relay in radial distribution networks

Energy Technology Data Exchange (ETDEWEB)

Conde, A.; Vazquez, E. [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Mecanica y Electrica, A.P. 36-F, CU, CP 66450, San Nicolas de los Garza, Nuevo Leon (Mexico)

2011-02-15

This paper contains the application criteria and coordination process for a proposed overcurrent relay in a radial power system with feed from one or multiple sources. This relay uses independent functions to detect faults and to calculate the operation time. Also this relay uses a time element function that allows it to reduce the time relay operation, enhancing the backup protection. Some of the proposed approaches improve the sensitivity of the relay. The selection of the best approach in the proposed relay is defined by the needs of the application. The proposed protection can be considered as an additional function protection to conventional overcurrent relays. (author)

Time of arrival based location estimation for cooperative relay networks

KAUST Repository

Ç elebi, Hasari Burak; Abdallah, Mohamed M.; Hussain, Syed Imtiaz; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

2010-01-01

In this paper, we investigate the performance of a cooperative relay network performing location estimation through time of arrival (TOA). We derive Cramer-Rao lower bound (CRLB) for the location estimates using the relay network. The analysis is extended to obtain average CRLB considering the signal fluctuations in both relay and direct links. The effects of the channel fading of both relay and direct links and amplification factor and location of the relay node on average CRLB are investigated. Simulation results show that the channel fading of both relay and direct links and amplification factor and location of relay node affect the accuracy of TOA based location estimation. ©2010 IEEE.

Time of arrival based location estimation for cooperative relay networks

KAUST Repository

Çelebi, Hasari Burak

2010-09-01

In this paper, we investigate the performance of a cooperative relay network performing location estimation through time of arrival (TOA). We derive Cramer-Rao lower bound (CRLB) for the location estimates using the relay network. The analysis is extended to obtain average CRLB considering the signal fluctuations in both relay and direct links. The effects of the channel fading of both relay and direct links and amplification factor and location of the relay node on average CRLB are investigated. Simulation results show that the channel fading of both relay and direct links and amplification factor and location of relay node affect the accuracy of TOA based location estimation. ©2010 IEEE.

A study of relay, breaker, instrumentation and control failures during an earthquake, and their effect on nuclear power plant safety

International Nuclear Information System (INIS)

Lambert, H.E.; Budnitz, R.J.

1987-01-01

In this project, an improved PRA systems analysis methodology for post-earthquake relay-chatter analysis is developed, and its use is demonstrated through analysis of the Zion-1 and LaSalle-2 reactors as case studies. For both Zion-1 and LaSalle-2, assuming that loss of offsite power (LOSP) occurs after a large earthquake and that there are no operator recovery actions, the analysis finds very many combinations (Boolean minimal cut sets) involving chatter of three or four relays and/or pressure switch contacts. The number is so large that there is a very high likelihood (of the order of unity) that at least one combination will occur after earthquake-caused LOSP. This conclusion depends in detail on the fragility curves and response assumptions used for chatter. (orig.)

Full-Duplex opportunistic relay selection in future spectrum-sharing networks

KAUST Repository

Khafagy, Mohammad Galal; Alouini, Mohamed-Slim; Aï ssa, Sonia

2015-01-01

We propose and analyze the performance of full-duplex relay selection in primary/secondary spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay, thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic relay selection among a cluster of full-duplex decode-and-forward relays with self-interference by deriving the exact cumulative distribution function of its end-to-end signal-to-noise ratio. Second, we evaluate the end-to-end performance of relay selection with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

Full-Duplex opportunistic relay selection in future spectrum-sharing networks

KAUST Repository

Khafagy, Mohammad Galal

2015-06-01

We propose and analyze the performance of full-duplex relay selection in primary/secondary spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay, thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic relay selection among a cluster of full-duplex decode-and-forward relays with self-interference by deriving the exact cumulative distribution function of its end-to-end signal-to-noise ratio. Second, we evaluate the end-to-end performance of relay selection with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

Discrete radioisotopic relays of a cyclic action

International Nuclear Information System (INIS)

Klempner, K.S.; Vasil'ev, A.G.

1975-01-01

A functional diagram of discrete radioisotopic relay equipment (RRP) with cyclic action was examined. An analysis of its rapid action and reliability under stationary conditions and transition regimes is presented. A structural diagram of radioisotopic relay equipment shows three radiation detectors, a pulse standardizer, an integrator and a power amplifier with a threshold cut-off device. It was established that the basic properties of the RRP - rapid action and reliability - are determined entirely by the counting rate of the average frequency of pulses from the radiation detector, n 0 and n 1 , in the 0 and 1 states (absence of current in the electromagnetic relay winding and activation of the winding of the output relay), capacities N 1 and N 2 of the dual counters, and the frequency of the transition threshold, f, of the generator. Formulas are presented which allow making engineering calculations for determining the optimum RRP parameters. High speed and reliability are shown, which are determined by the production purposes of the relay

Asymmetric Modulation Gains in Network Coded Relay Networks

DEFF Research Database (Denmark)

Roetter, Daniel Enrique Lucani; Fitzek, Frank

2015-01-01

Wireless relays have usually been considered in two ways. On the one hand, a physical layer approach focused on per-packet reliability and involving the relay on each packet transmission. On the other, recent approaches have relied on the judicious activation of the relay at the network level to ...

Beamforming Design for Coordinated Direct and Relay Systems

DEFF Research Database (Denmark)

Sun, Fan; De Carvalho, Elisabeth; Thai, Chan

2012-01-01

Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying based on wireless network coding. Recently, a related set of techniques has emerged, termed coordinated direct and relay (CDR) transmissions......, where the constellation of traffic flows is more general than the two-way. Regardless of the actual traffic flows, in a CDR scheme the relay has a central role in managing the interference. In this paper we investigate the novel transmission modes, based on amplify-and-forward, that arise when the relay...... an iterative solution, as well as derive an upper performance bound. The numerical results demonstrate a clear benefit from usage of multiple antennas at the relay node....

Reduced Wall Acetylation Proteins Play Vital and Distinct Roles in Cell Wall O-Acetylation in Arabidopsis

DEFF Research Database (Denmark)

Manabe, Yuzuki; Verhertbruggen, Yves; Gille, Sascha

2013-01-01

The Reduced Wall Acetylation (RWA) proteins are involved in cell wall acetylation in plants. Previously, we described a single mutant, rwa2, which has about 20% lower level of O-acetylation in leaf cell walls and no obvious growth or developmental phenotype. In this study, we generated double....... The quadruple rwa mutant can be completely complemented with the RWA2 protein expressed under 35S promoter, indicating the functional redundancy of the RWA proteins. Nevertheless, the degree of acetylation of xylan, (gluco) mannan, and xyloglucan as well as overall cell wall acetylation is affected differently...... in different combinations of triple mutants, suggesting their diversity in substrate preference. The overall degree of wall acetylation in the rwa quadruple mutant was reduced by 63% compared with the wild type, and histochemical analysis of the rwa quadruple mutant stem indicates defects in cell...

Robust distributed cognitive relay beamforming

KAUST Repository

Pandarakkottilil, Ubaidulla

2012-05-01

In this paper, we present a distributed relay beamformer design for a cognitive radio network in which a cognitive (or secondary) transmit node communicates with a secondary receive node assisted by a set of cognitive non-regenerative relays. The secondary nodes share the spectrum with a licensed primary user (PU) node, and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. The proposed robust cognitive relay beamformer design seeks to minimize the total relay transmit power while ensuring that the transceiver signal-to-interference- plus-noise ratio and PU interference constraints are satisfied. The proposed design takes into account a parameter of the error in the channel state information (CSI) to render the performance of the beamformer robust in the presence of imperfect CSI. Though the original problem is non-convex, we show that the proposed design can be reformulated as a tractable convex optimization problem that can be solved efficiently. Numerical results are provided and illustrate the performance of the proposed designs for different network operating conditions and parameters. © 2012 IEEE.

Distance relay performance in future converter dominated power systems

DEFF Research Database (Denmark)

Sarkar, Moumita; Jia, Jundi; Yang, Guangya

2017-01-01

Increasing penetration of converter-based generations in power system has led to new system challenges. Short circuit power response from converter-based generations is different from that of traditional synchronous generators. Power electronic converters can be designed for over-current only up ...... of converter controls on fault current response of converter-based generations is also investigated. Index Terms—Converter control, distance relays, power system protection, system modelling....... to 1.1-1.25 times of its nominal value. Low availability of short circuit power can cause many challenges such as misoperation of distance relays. The aim of this paper is to investigate the effect of converter dominated systems on performance of distance relays. Backup functionality of the distance...... relay is major concern as miscoordination of backup relays in case of cascading faults can lead to severe stress in system, which can develop into blackout. In this paper, response of relays in traditional system is compared with response of relays in low short-circuit-current power systems. Impact...

Distributed stability control using intelligent voltage-margin relay

Energy Technology Data Exchange (ETDEWEB)

Wiszniewski, A.; Rebizant, W. [Wroclaw Univ. of Technology (Poland); Klimek, A. [Powertech Labs Inc., Surrey, BC (Canada)

2010-07-01

This paper presented an intelligent relay that operates if the load to source impedance ratio decreases to a level that is dangerously close to the stability limit, which leads to power system blackouts. The intelligent voltage-margin/difference relay installed at receiving substations automatically initiates action if the voltage stability margin drops to a dangerously low level. The relay decides if the tap changing devices are to be blocked and if under-voltage load shedding should be initiated, thereby mitigating an evolving instability. The intelligent relay has two levels of operation. At the first stage, which corresponds to the higher load to source impedance ratio, the relay initiates blocking of the tap changer. At the second stage, corresponding to the lower source to load impedance ratio, load shedding is initiated. The relay operates when the load to source impedance ratio reaches a certain predetermined level, but it does not depend either on the level of the source voltage or on the difference of source and load impedance phase angles. The algorithm for the relay is relatively simple and uses only locally available signals. Consequently, the transformer is well controlled to eliminate the cases of voltage instability. 6 refs., 7 figs.

Acetylation of woody lignocellulose: significance and regulation

Directory of Open Access Journals (Sweden)

Prashant Mohan-Anupama Pawar

2013-05-01

Full Text Available Non-cellulosic cell wall polysaccharides constitute approximately one quarter of usable biomass for human exploitation. In contrast to cellulose, these components are usually substituted by O-acetyl groups, which affect their properties and interactions with other polymers, thus affecting their solubility and extractability. However, details of these interactions are still largely obscure. Moreover, polysaccharide hydrolysis to constituent monosaccharides, is hampered by the presence of O-acetyl groups, necessitating either enzymatic (esterase or chemical de-acetylation, increasing the costs and chemical consumption. Reduction of polysaccharide acetyl content in planta is a way to modify lignocellulose towards improved saccharification. In this review we: 1 summarize literature on lignocellulose acetylation in different tree species, 2 present data and current hypotheses concerning the role of O-acetylation in determining woody lignocellulose properties, 3 describe plant proteins involved in lignocellulose O-acetylation, 4 give examples of microbial enzymes capable to de-acetylate lignocellulose, and 5 discuss prospects for exploiting these enzymes in planta to modify xylan acetylation.

Asymptotic analysis for Nakagami-m fading channels with relay selection

KAUST Repository

Zhong, Caijun

2011-06-01

In this paper, we analyze the asymptotic outage probability performance of both decode-and-forward (DF) and amplify-and-forward (AF) relaying systems using partial relay selection and the "best" relay selection schemes for Nakagami-m fading channels. We derive their respective outage probability expressions in the asymptotic high signal-to-noise ratio (SNR) regime, from which the diversity order and coding gain are analyzed. In addition, we investigate the impact of power allocation between the source and relay terminals and derive the diversity-multiplexing tradeoff (DMT) for these relay selection systems. The theoretical findings suggest that partial relay selection can improve the diversity of the system and can achieve the same DMT as the "best" relay selection scheme under certain conditions. © 2011 IEEE.

LTE-Advanced Relay Technology and Standardization

CERN Document Server

Yuan, Yifei

2013-01-01

LTE-Advanced Relay Technology and Standardization provides a timely reference work for relay technology with the finalizing of LTE Release 10 specifications. LTE-Advanced is quickly becoming the global standard for 4G cellular communications. The relay technology, as one of the key features in LTE-Advanced, helps not only to improve the system coverage and capacity, but also to save the costs of laying wireline backhaul. As a leading researcher in the field of LTE-Advanced standards, the author provides an in-depth description of LTE-A relay technology, and explains in detail the standard specification and design principles.     Readers from both academic and industrial fields can find sections of interest to them: Sections 2 & 4 could benefit researchers in academia and those who are engaged in exploratory work, while Sections 3 & 4 are more useful to engineers. Dr. Yifei Yuan is the Technical Director at the Standards Department of ZTE Inc.

Cancer drug addiction is relayed by an ERK2-dependent phenotype switch.

Science.gov (United States)

Kong, Xiangjun; Kuilman, Thomas; Shahrabi, Aida; Boshuizen, Julia; Kemper, Kristel; Song, Ji-Ying; Niessen, Hans W M; Rozeman, Elisa A; Geukes Foppen, Marnix H; Blank, Christian U; Peeper, Daniel S

2017-10-12

Observations from cultured cells, animal models and patients raise the possibility that the dependency of tumours on the therapeutic drugs to which they have acquired resistance represents a vulnerability with potential applications in cancer treatment. However, for this drug addiction trait to become of clinical interest, we must first define the mechanism that underlies it. We performed an unbiased CRISPR-Cas9 knockout screen on melanoma cells that were both resistant and addicted to inhibition of the serine/threonine-protein kinase BRAF, in order to functionally mine their genome for 'addiction genes'. Here we describe a signalling pathway comprising ERK2 kinase and JUNB and FRA1 transcription factors, disruption of which allowed addicted tumour cells to survive on treatment discontinuation. This occurred in both cultured cells and mice and was irrespective of the acquired drug resistance mechanism. In melanoma and lung cancer cells, death induced by drug withdrawal was preceded by a specific ERK2-dependent phenotype switch, alongside transcriptional reprogramming reminiscent of the epithelial-mesenchymal transition. In melanoma cells, this reprogramming caused the shutdown of microphthalmia-associated transcription factor (MITF), a lineage survival oncoprotein; restoring this protein reversed phenotype switching and prevented the lethality associated with drug addiction. In patients with melanoma that had progressed during treatment with a BRAF inhibitor, treatment cessation was followed by increased expression of the receptor tyrosine kinase AXL, which is associated with the phenotype switch. Drug discontinuation synergized with the melanoma chemotherapeutic agent dacarbazine by further suppressing MITF and its prosurvival target, B-cell lymphoma 2 (BCL-2), and by inducing DNA damage in cancer cells. Our results uncover a pathway that underpins drug addiction in cancer cells, which may help to guide the use of alternating therapeutic strategies for enhanced

New results on performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

2013-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may

Accurate performance analysis of opportunistic decode-and-forward relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2011-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may

Electric equipment technical regulation on a relay

International Nuclear Information System (INIS)

1995-01-01

It is about a relay for power protection. It describes the definitions of structure, a point of contact protection of contact, reclosing, relay scheme and input circuit. It explains normal use condition, special use condition, rated frequency, rated voltage and rated current, fluctuation range of permission of incoming relay. It deals with general structing outer case, correction device, operation indicator and outer terminal condition sort and method of the test. It adds the marks and pictures about currents

Location-based Relay Selection and Power Adaptation Enabling Simultaneous Transmissions

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Madsen, Tatiana Kozlova; Schwefel, Hans-Peter

2010-01-01

Relaying is a well known technique to extend coverage and improve conditions for nodes in the outer coverage region. In this paper we propose a relaying scheme that exploits the spatial separation of relay and destination pairs to improve throughput by allowing simultaneous transmissions....... The proposed scheme is a cross-layer optimization for two-hop relaying that uses position information to jointly optimize relay selection and relay transmit power, maximizing Medium Access Control layer throughput. Further, in order to calculate the expected throughput, we apply a probabilistic model...... that takes into account MAC retransmissions and timing behavior of the IEEE 802.11 Distributed Coordination Function mode. Our results show an increase in throughput of approximately 20% is achievable for the proposed scheme when compared to two-hop relaying in the analyzed scenario....

2-Acetylthiamin pyrophosphate (acetyl-TPP) pH-rate profile for hydrolysis of acetyl-TPP and isolation of acetyl-TPP as a transient species in pyruvate dehydrogenase catalyzed reactions

International Nuclear Information System (INIS)

Gruys, K.J.; Datta, A.; Frey, P.A.

1989-01-01

Rate constants for the hydrolysis of acetyl-TPP were measured pH values of 2.5 and 7.5 and plotted as log k obs versus pH. The pH-rate profile defined two legs, each with a slope of +1 but separated by a region of decreased slope between pH 4 and pH 6. The rates were insensitive to buffer concentrations. Each leg of the profile reflected specific-base-catalyzed hydrolysis of acetyl-TPP, analogous to the hydrolysis of 2-acetyl-3,4-dimethylthiazolium ion. The separation of the two legs of this profile has been shown to be caused by the ionization of a group exhibiting a pK a of 4.73 within acetyl-TPP that is remote from the acetyl group, the aminopyrimidine ring, which is promoted below pH 4.73. The protonation level of this ring has been shown to control the equilibrium partitioning of acetyl-TPP among its carbinolamine, keto, and hydrate forms. The differential partitioning of these species is a major factor causing the separation between the two legs of the pH-rate profile. The characteristic pH-rate profile and the availability of synthetic acetyl-TPP have facilitated the isolation and identification of [1- 14 C]acetyl-TPP from acid-quenched enymatic reaction mixtures at steady states. [1- 14 C]Acetyl-TPP was identified as a transient species in reactions catalyzed by the PDH complex or the pyruvate dehydrogenase component of the complex (E 1 ). The pH-rate profile for hydrolysis of [1- 14 C]-acetyl-TPP, isolated from enzymatic reactions was found to be indistinguishable from that for authentic acetyl-TPP, which constituted positive identification of the 14 C-labeled enzymic species

Performance of hybrid-ARQ with incremental redundancy over relay channels

KAUST Repository

Chelli, Ali

2012-12-01

In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears the transmitted messages over the different HARQ rounds and tries to decode the data packet. In case of successful decoding at the relay, both the relay and the source cooperate to transmit the message to the destination. A maximum number M of HARQ rounds is considered. The channel realizations are independent for different HARQ rounds. We assume Rayleigh fading channels for the links source-relay, source-destination, and relay-destination. We investigate the performance of HARQ-IR over relay channel from an information theoretic perspective. Analytical expressions are derived for the information outage probability, the average number of transmissions, and the average transmission rate. We illustrate through our investigation the benefit of relaying. We also show the impact of the target outage probability and the maximum number M of HARQ rounds on the outage probability, the average number of transmissions, and the average transmission rate. © 2012 IEEE.

On Buffer-Aided Multiple-Access Relay Channel

DEFF Research Database (Denmark)

Liu, Rongkuan; Popovski, Petar; Wang, Gang

2016-01-01

This letter treats uplink scenario where M user equipments (UEs) send to a base station (BS), possibly via a common relay station (RS) that is equipped with a buffer. This is a multiple-access relay channel aided by a buffer. We devise a protocol in which the transmission mode is selected...... entirely at the BS, while simultaneously a number of UEs sends new messages to the BS. The results show that the adaptive selection of direct and buffer-aided relay transmissions leads to significant average throughput gains....

Cooperative AF Relaying in Spectrum-Sharing Systems: Outage Probability Analysis under Co-Channel Interferences and Relay Selection

KAUST Repository

Xia, Minghua

2012-11-01

For cooperative amplify-and-forward (AF) relaying in spectrum-sharing wireless systems, secondary users share spectrum resources originally licensed to primary users to communicate with each other and, thus, the transmit power of secondary transmitters is strictly limited by the tolerable interference powers at primary receivers. Furthermore, the received signals at a relay and at a secondary receiver are inevitably interfered by the signals from primary transmitters. These co-channel interferences (CCIs) from concurrent primary transmission can significantly degrade the performance of secondary transmission. This paper studies the effect of CCIs on outage probability of the secondary link in a spectrum-sharing environment. In particular, in order to compensate the performance loss due to CCIs, the transmit powers of a secondary transmitter and its relaying node are respectively optimized with respect to both the tolerable interference powers at the primary receivers and the CCIs from the primary transmitters. Moreover, when multiple relays are available, the technique of opportunistic relay selection is exploited to further improve system performance with low implementation complexity. By analyzing lower and upper bounds on the outage probability of the secondary system, this study reveals that it is the tolerable interference powers at primary receivers that dominate the system performance, rather than the CCIs from primary transmitters. System designers will benefit from this result in planning and designing next-generation broadband spectrum-sharing systems.

Acetyl Fentanyl Toxicity: Two Case Reports.

Science.gov (United States)

Fort, Chelsea; Curtis, Byron; Nichols, Clay; Niblo, Cheryl

2016-11-01

Acetyl fentanyl is an illicit fentanyl analog recently appearing in forensic casework. A quantitative method was created for measuring acetyl fentanyl in various biological matrices acquired post-mortem due to recent positive screening results in casework. Initial detection by immunoassay and standard gas chromatography mass spectrometry (GC/MS) methods have been previously reported for acetyl fentanyl and are examined further here. A Selective Ion Monitoring (SIM) method was created using a GC/MS for quantitation. In two separate cases, acetyl fentanyl was found to be in similar concentrations to those previously reported and ruled to be the cause of death. Acetyl fentanyl concentrations were determined in blood samples, liver, brain, vitreous humor, and urine. Individual 1 had acetyl fentanyl concentrations as follows: heart blood-285 ng/mL, femoral blood-192 ng/mL, liver-1,100 ng/g, brain-620 ng/g, and urine-3,420 ng/mL. Individual 2 had acetyl fentanyl concentrations as follows: heart blood-210 ng/mL, femoral blood-255 ng/mL, urine-2,720 ng/mL and vitreous humor-140 ng/mL. Experimental conditions for screening and quantitation are provided, using immunoassay and GC/MS methods. Due to the recent emergence of acetyl fentanyl, more data will need to be generated to fully differentiate recreational and fatal concentrations of acetyl fentanyl to assist toxicologists accurately understanding its physiological impact. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Relay self interference minimisation using tapped filter

KAUST Repository

Jazzar, Saleh; Al-Naffouri, Tareq Y.

2013-01-01

In this paper we introduce a self interference (SI) estimation and minimisation technique for amplify and forward relays. Relays are used to help forward signals between a transmitter and a receiver. This helps increase the signal coverage

Sequential Dy(OTf)3 -Catalyzed Solvent-Free Per-O-Acetylation and Regioselective Anomeric De-O-Acetylation of Carbohydrates.

Science.gov (United States)

Yan, Yi-Ling; Guo, Jiun-Rung; Liang, Chien-Fu

2017-09-19

Dysprosium(III) trifluoromethanesulfonate-catalyzed per-O-acetylation and regioselective anomeric de-O-acetylation of carbohydrates can be tuned by adjusting the reaction medium. In this study, the per-O-acetylation of unprotected sugars by using a near-stoichiometric amount of acetic anhydride under solvent-free conditions resulted in the exclusive formation of acetylated saccharides as anomeric mixtures, whereas anomeric de-O-acetylation in methanol resulted in a moderate-to-excellent yield. Reactions with various unprotected monosaccharides or disaccharides followed by a semi-one-pot sequential conversion into the corresponding acetylated glycosyl hemiacetal also resulted in high yields. Furthermore, the obtained hemiacetals could be successfully transformed into trichloroimidates after Dy(OTf) 3 -catalyzed glycosylation. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Relay selection from an effective capacity perspective

KAUST Repository

Yang, Yuli; Ma, Hao; Aï ssa, Sonia

2013-01-01

proposed scheme in certain scenarios. Moreover, the analysis presented herein offers a convenient tool to the relaying transmission design, specifically on which relay selection scheme should be used as well as how to choose the receiving strategy between

76 FR 72124 - Internet-Based Telecommunications Relay Service Numbering

Science.gov (United States)

2011-11-22

... Docket No. 10-191; FCC 11-123] Internet-Based Telecommunications Relay Service Numbering AGENCY: Federal..., the information collection associated with the Commission's Internet- Based Telecommunications Relay... Telecommunications Relay Service Numbering, CG Docket No. 03-123; WC Docket No. 05-196; WC Docket No. 10-191; FCC 11...

Using a micromachined magnetostatic relay in commutating a DC motor

Science.gov (United States)

Tai, Yu-Chong (Inventor); Wright, John A. (Inventor); Lilienthal, Gerald (Inventor)

2004-01-01

A DC motor is commutated by rotating a magnetic rotor to induce a magnetic field in at least one magnetostatic relay in the motor. Each relay is activated in response to the magnetic field to deliver power to at least one corresponding winding connected to the relay. In some cases, each relay delivers power first through a corresponding primary winding and then through a corresponding secondary winding to a common node. Specific examples include a four-pole, three-phase motor in which each relay is activated four times during one rotation of the magnetic rotor.

Relay-assited transmission and radio resource management for wireless networks

OpenAIRE

Agustín de Dios, Adrián

2008-01-01

La transmisión asistida por relay o transmisión cooperativa es una nueva técnica de diversidad espacial donde aparece un elemento nuevo (un relay o un usuario cooperativo) en la tradicional transmisión punto a punto (fuente a destino). Ahora en la comunicación intervienen tres enlaces: fuente-relay, relay-destino y fuente-destino. El relay, además de asistir a la fuente en la transmisión de un mensaje, permite combatir las degradaciones que puede sufrir el canal como el shadowing y el pathlos...

Optimized Policies for Improving Fairness of Location-based Relay Selection

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Olsen, Rasmus Løvenstein; Madsen, Tatiana Kozlova

2013-01-01

For WLAN systems in which relaying is used to improve throughput performance for nodes located at the cell edge, node mobility and information collection delays can have a significant impact on the performance of a relay selection scheme. In this paper we extend our existing Markov Chain modeling...... framework for relay selection to allow for efficient calculation of relay policies given either mean throughput or kth throughput percentile as optimization criterium. In a scenario with static access point, static relay, and a mobile destination node, the kth throughput percentile optimization...

Generalized instantly decodable network coding for relay-assisted networks

KAUST Repository

Elmahdy, Adel M.

2013-09-01

In this paper, we investigate the problem of minimizing the frame completion delay for Instantly Decodable Network Coding (IDNC) in relay-assisted wireless multicast networks. We first propose a packet recovery algorithm in the single relay topology which employs generalized IDNC instead of strict IDNC previously proposed in the literature for the same relay-assisted topology. This use of generalized IDNC is supported by showing that it is a super-set of the strict IDNC scheme, and thus can generate coding combinations that are at least as efficient as strict IDNC in reducing the average completion delay. We then extend our study to the multiple relay topology and propose a joint generalized IDNC and relay selection algorithm. This proposed algorithm benefits from the reception diversity of the multiple relays to further reduce the average completion delay in the network. Simulation results show that our proposed solutions achieve much better performance compared to previous solutions in the literature. © 2013 IEEE.

Optimal Contract Design for Cooperative Relay Incentive Mechanism under Moral Hazard

Directory of Open Access Journals (Sweden)

Nan Zhao

2015-01-01

Full Text Available Cooperative relay can effectively improve spectrum efficiency by exploiting the spatial diversity in the wireless networks. However, wireless nodes may acquire different network information with various users’ location and mobility, channels’ conditions, and other factors, which results in asymmetric information between the source and the relay nodes (RNs. In this paper, the relay incentive mechanism between relay nodes and the source is investigated under the asymmetric information. By modelling multiuser cooperative relay as a labour market, a contract model with moral hazard for relay incentive is proposed. To effectively incentivize the potential RNs to participate in cooperative relay, the optimization problems are formulated to maximize the source’s utility while meeting the feasible conditions under both symmetric and asymmetric information scenarios. Numerical simulation results demonstrate the effectiveness of the proposed contract design scheme for cooperative relay.

A performance analysis in AF full duplex relay selection network

Science.gov (United States)

Ngoc, Long Nguyen; Hong, Nhu Nguyen; Loan, Nguyen Thi Phuong; Kieu, Tam Nguyen; Voznak, Miroslav; Zdralek, Jaroslav

2018-04-01

This paper studies on the relaying selective matter in amplify-and-forward (AF) cooperation communication with full-duplex (FD) activity. Various relay choice models supposing the present of different instant information are investigated. We examine a maximal relaying choice that optimizes the instant FD channel capacity and asks for global channel state information (CSI) as well as partial CSI learning. To make comparison easy, accurate outage probability clauses and asymptote form of these strategies that give a diversity rank are extracted. From that, we can see clearly that the number of relays, noise factor, the transmittance coefficient as well as the information transfer power had impacted on their performance. Besides, the optimal relay selection (ORS) model can promote than that of the partial relay selection (PRS) model.

STUDI ANALISIS KOORDINASI OVER CURRENT RELAY (OCR DAN GROUND FAULT RELAY (GFR PADA RECLOSER DI SALURAN PENYULANG PENEBEL

Directory of Open Access Journals (Sweden)

I Dewa Gde Agung Budhi Udiana

2017-08-01

Full Text Available Short circuit causing over current problem and can might causing interference of the equipment performance such as distribution transformers also causing widespread disruption occurred. In resolving such interference is required as protection system on the distribution system. Seeing all above is needed coordination between the supporting component of the protection system which is consisted of Over Current Relay (OCR and Ground Fault Relay (GFR. The research was conducted at PT. PLN (Persero South Bali Area Network, INDONESIA on recloser in the feeder line of Penebel. OCR setting between the Relay feeder of Penebel, Recloser Celagi, Recloser Bakisan, and Recloser Benana still less selective, with time value coordination between average security was still less than 0,2 second. Then OCR setting and GFR relay feeder of Penebel, Recloser Celagi, Recloser Bakisan, and Recloser Benana was recommended for re-setting in order to minimize disruption and electric power distribution system to be reliable.

Two-way CSI-assisted AF relaying with HPA nonlinearity

KAUST Repository

Qi, Jian

2015-09-11

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal-to-noise ratio (SNR) is derived as per the modified system model by taking into account the interference caused by relaying scheme and HPA nonlinearity. The system performance of the considered relaying network is evaluated in terms of average symbol error probability (SEP) in Nakagami-m fading channels, by making use of the moment-generating function (MGF) approach. Numerical results are provided and show the effects of several parameters, such as quadrature amplitude modulation (QAM) order, number of relays, HPA parameters, and Nakagami parameter, on performance. © 2015 IEEE.

Spreading Sequence System for Full Connectivity Relay Network

Science.gov (United States)

Kwon, Hyuck M. (Inventor); Yang, Jie (Inventor); Pham, Khanh D. (Inventor)

2018-01-01

Fully connected uplink and downlink fully connected relay network systems using pseudo-noise spreading and despreading sequences subjected to maximizing the signal-to-interference-plus-noise ratio. The relay network systems comprise one or more transmitting units, relays, and receiving units connected via a communication network. The transmitting units, relays, and receiving units each may include a computer for performing the methods and steps described herein and transceivers for transmitting and/or receiving signals. The computer encodes and/or decodes communication signals via optimum adaptive PN sequences found by employing Cholesky decompositions and singular value decompositions (SVD). The PN sequences employ channel state information (CSI) to more effectively and more securely computing the optimal sequences.

Four-Way Relaying in Wireless Cellular Systems

DEFF Research Database (Denmark)

Liu, Huaping; Popovski, Petar; De Carvalho, Elisabeth

2013-01-01

Two-way relaying in wireless systems has initiated a large research effort during the past few years. Nevertheless, it represents only a specific traffic pattern and it is of interest to investigate other traffic patterns where such a simultaneous processing of information flows can bring...... performance advantage. In this paper we consider a \\emph{four-way relaying} scenario, where each of the two Mobile Stations (MSs) has a two-way connection to the same Base Station (BS), while each connection is through a dedicated Relay Station (RS). The RSs are placed in such a way that one RS...... of the new scheme for Decode-and-Forward (DF) operational model for the RS. We compare the performance with a state-of-the-art reference scheme, based on two-way relaying with DF. The results indicate that the achievable rate regions are significantly enlarged for the new scheme....

Systematic Network Coding with the Aid of a Full-Duplex Relay

DEFF Research Database (Denmark)

Giacaglia, Giuliano; Shi, Xiaomeng; Kim, MinJi

2013-01-01

is to deliver a given number of data packets to a receiver with the aid of a relay. The source broadcasts to both the receiver and the relay using one frequency, while the relay uses another frequency for transmissions to the receiver, allowing for a full-duplex operation of the relay. We analyze the decoding...... complexity and delay performance of two types of relays: one that preserves the systematic structure of the code from the source; another that does not. A systematic relay forwards uncoded packets upon reception, but transmits coded packets to the receiver after receiving the first coded packet from...

Mobile User Connectivity in Relay-Assisted Visible Light Communications

Directory of Open Access Journals (Sweden)

Petr Pešek

2018-04-01

Full Text Available In this paper, we investigate relay-assisted visible light communications (VLC where a mobile user acts as a relay and forwards data from a transmitter to the end mobile user. We analyse the utilization of the amplify-and-forward (AF and decode-and-forward (DF relaying schemes. The focus of the paper is on analysis of the behavior of the mobile user acting as a relay while considering a realistic locations of the receivers and transmitters on a standard mobile phone, more specifically with two photodetectors on both sides of a mobile phone and a transmitting LED array located upright. We also investigate dependency of the bit error rate (BER performance on the azimuth and elevation angles of the mobile relay device within a typical office environment. We provide a new analytical description of BER for AF and DF-based relays in VLC. In addition we compare AF and DF-based systems and show that DF offers a marginal improvement in the coverage area with a BER < 10–3 and a data rate of 100 Mb/s. Numerical results also illustrate that relay-based systems offer a significant improvement in terms of the coverage compared to direct non-line of sight VLC links.

47 CFR 11.20 - State Relay Network.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false State Relay Network. 11.20 Section 11.20... Network. This network is composed of State Relay (SR) sources, leased common carrier communications facilities or any other available communication facilities. The network distributes State EAS messages...

Performance of hybrid-ARQ with incremental redundancy over relay channels

KAUST Repository

Chelli, Ali; Alouini, Mohamed-Slim

2012-01-01

In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears

Asymptotic analysis for Nakagami-m fading channels with relay selection

KAUST Repository

Zhong, Caijun; Wong, Kaikit; Jin, Shi; Alouini, Mohamed-Slim; Ratnarajah, Tharm

2011-01-01

In this paper, we analyze the asymptotic outage probability performance of both decode-and-forward (DF) and amplify-and-forward (AF) relaying systems using partial relay selection and the "best" relay selection schemes for Nakagami-m fading channels

Efficient Resource Scheduling by Exploiting Relay Cache for Cellular Networks

Directory of Open Access Journals (Sweden)

Chun He

2015-01-01

Full Text Available In relay-enhanced cellular systems, throughput of User Equipment (UE is constrained by the bottleneck of the two-hop link, backhaul link (or the first hop link, and access link (the second hop link. To maximize the throughput, resource allocation should be coordinated between these two hops. A common resource scheduling algorithm, Adaptive Distributed Proportional Fair, only ensures that the throughput of the first hop is greater than or equal to that of the second hop. But it cannot guarantee a good balance of the throughput and fairness between the two hops. In this paper, we propose a Two-Hop Balanced Distributed Scheduling (TBS algorithm by exploiting relay cache for non-real-time data traffic. The evolved Node Basestation (eNB adaptively adjusts the number of Resource Blocks (RBs allocated to the backhaul link and direct links based on the cache information of relays. Each relay allocates RBs for relay UEs based on the size of the relay UE’s Transport Block. We also design a relay UE’s ACK feedback mechanism to update the data at relay cache. Simulation results show that the proposed TBS can effectively improve resource utilization and achieve a good trade-off between system throughput and fairness by balancing the throughput of backhaul and access link.

Wireless Energy Harvesting Two-Way Relay Networks with Hardware Impairments.

Science.gov (United States)

Peng, Chunling; Li, Fangwei; Liu, Huaping

2017-11-13

This paper considers a wireless energy harvesting two-way relay (TWR) network where the relay has energy-harvesting abilities and the effects of practical hardware impairments are taken into consideration. In particular, power splitting (PS) receiver is adopted at relay to harvests the power it needs for relaying the information between the source nodes from the signals transmitted by the source nodes, and hardware impairments is assumed suffered by each node. We analyze the effect of hardware impairments [-20]on both decode-and-forward (DF) relaying and amplify-and-forward (AF) relaying networks. By utilizing the obtained new expressions of signal-to-noise-plus-distortion ratios, the exact analytical expressions of the achievable sum rate and ergodic capacities for both DF and AF relaying protocols are derived. Additionally, the optimal power splitting (OPS) ratio that maximizes the instantaneous achievable sum rate is formulated and solved for both protocols. The performances of DF and AF protocols are evaluated via numerical results, which also show the effects of various network parameters on the system performance and on the OPS ratio design.

Developing a Domain Model for Relay Circuits

DEFF Research Database (Denmark)

Haxthausen, Anne Elisabeth

2009-01-01

In this paper we stepwise develop a domain model for relay circuits as used in railway control systems. First we provide an abstract, property-oriented model of networks consisting of components that can be glued together with connectors. This model is strongly inspired by a network model...... for railways madeby Bjørner et.al., however our model is more general: the components can be of any kind and can later be refined to e.g. railway components or circuit components. Then we show how the abstract network model can be refined into an explicit model for relay circuits. The circuit model describes...... the statics as well as the dynamics of relay circuits, i.e. how a relay circuit can be composed legally from electrical components as well as how the components may change state over time. Finally the circuit model is transformed into an executable model, and we show how a concrete circuit can be defined...

An RSS based location estimation technique for cognitive relay networks

KAUST Repository

Qaraqe, Khalid A.; Hussain, Syed Imtiaz; Ç elebi, Hasari Burak; Abdallah, Mohamed M.; Alouini, Mohamed-Slim

2010-01-01

In this paper, a received signal strength (RSS) based location estimation method is proposed for a cooperative wireless relay network where the relay is a cognitive radio. We propose a method for the considered cognitive relay network to determine

Breaking the Myth That Relay Swimming Is Faster Than Individual Swimming.

Science.gov (United States)

Skorski, Sabrina; Etxebarria, Naroa; Thompson, Kevin G

2016-04-01

To investigate if swimming performance is better in a relay race than in the corresponding individual race. The authors analyzed 166 elite male swimmers from 15 nations in the same competition (downloaded from www.swimrankings.net). Of 778 observed races, 144 were Olympic Games performances (2000, 2004, 2012), with the remaining 634 performed in national or international competitions. The races were 100-m (n = 436) and 200-m (n = 342) freestyle events. Relay performance times for the 2nd-4th swimmers were adjusted (+ 0.73 s) to allow for the "flying start." Without any adjustment, mean individual relay performances were significantly faster for the first 50 m and overall time in the 100-m events. Furthermore, the first 100 m of the 200-m relay was significantly faster (P > .001). During relays, swimmers competing in 1st position did not show any difference compared with their corresponding individual performance (P > .16). However, swimmers competing in 2nd-4th relay-team positions demonstrated significantly faster times in the 100-m (P individual events (P team positions were adjusted for the flying start no differences were detected between relay and individual race performance for any event or split time (P > .17). Highly trained swimmers do not swim (or turn) faster in relay events than in their individual races. Relay exchange times account for the difference observed in individual vs relay performance.

Scalable DeNoise-and-Forward in Bidirectional Relay Networks

DEFF Research Database (Denmark)

Sørensen, Jesper Hemming; Krigslund, Rasmus; Popovski, Petar

2010-01-01

In this paper a scalable relaying scheme is proposed based on an existing concept called DeNoise-and-Forward, DNF. We call it Scalable DNF, S-DNF, and it targets the scenario with multiple communication flows through a single common relay. The idea of the scheme is to combine packets at the relay...... in order to save transmissions. To ensure decodability at the end-nodes, a priori information about the content of the combined packets must be available. This is gathered during the initial transmissions to the relay. The trade-off between decodability and number of necessary transmissions is analysed...

Sum-Rate Maximization of Coordinated Direct and Relay Systems

DEFF Research Database (Denmark)

Sun, Fan; Popovski, Petar; Thai, Chan

2012-01-01

Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying based on wireless network coding. Recently, a related set of techniques has emerged, termed coordinated direct and relay (CDR) transmissions......, where the constellation of traffic flows is more general than the two-way. Regardless of the actual traffic flows, in a CDR scheme the relay has a central role in managing the interference and boosting the overall system performance. In this paper we investigate the novel transmission modes, based...... on amplify-and-forward, that arise when the relay is equipped with multiple antennas and can use beamforming. We focus on one representative traffic type, with one uplink and one downlink users and consider the achievable sum-rate maximization relay beamforming. The beamforming criterion leads to a non...

Effects of relay chatter in seismic probabilistic safety analysis

International Nuclear Information System (INIS)

Reed, J.W.; Shiu, K.K.

1985-01-01

In the Zion and Indian Point Probabilistic Safety Studies, relay chatter was dismissed as a credible event and hence was not formally included in the analyses. Although little discussion is given in the Zion and Indian Point PSA documentation concerning the basis for this decision, it has been expressed informally that it was assumed that the operators will be able to reset all relays in a timely manner. Currently, it is the opinion of many professionals that this may be an oversimplification. The three basic areas which must be considered in addressing relay chatter include the fragility of the relays per se, the reliability of the operators to reset the relays and finally the systems response aspects. Each of these areas is reviewed and the implications for seismic PSA are discussed. Finally, recommendations for future research are given

Relay communications strategies for Mars exploration through 2020

Science.gov (United States)

Edwards, Charles D., Jr.; Arnold, B.; DePaula, R.; Kazz, G.; Lee, C.; Noreen, G.

2005-01-01

In this paper we will examine NASA's strategy for relay communications support of missions planned for this decade, and discuss options for longer-term relay network evolution in support of second-decade missions.

76 FR 65965 - Contributions to the Telecommunications Relay Services Fund

Science.gov (United States)

2011-10-25

...] Contributions to the Telecommunications Relay Services Fund AGENCY: Federal Communications Commission. ACTION... Telecommunications Relay Services (TRS) Fund in a manner prescribed by regulation that is consistent with and... . SUPPLEMENTARY INFORMATION: This is a summary of the Commission's Contributions to the Telecommunications Relay...

Acetylation of Mammalian ADA3 Is Required for Its Functional Roles in Histone Acetylation and Cell Proliferation.

Science.gov (United States)

Mohibi, Shakur; Srivastava, Shashank; Bele, Aditya; Mirza, Sameer; Band, Hamid; Band, Vimla

2016-10-01

Alteration/deficiency in activation 3 (ADA3) is an essential component of specific histone acetyltransferase (HAT) complexes. We have previously shown that ADA3 is required for establishing global histone acetylation patterns and for normal cell cycle progression (S. Mohibi et al., J Biol Chem 287:29442-29456, 2012, http://dx.doi.org/10.1074/jbc.M112.378901). Here, we report that these functional roles of ADA3 require its acetylation. We show that ADA3 acetylation, which is dynamically regulated in a cell cycle-dependent manner, reflects a balance of coordinated actions of its associated HATs, GCN5, PCAF, and p300, and a new partner that we define, the deacetylase SIRT1. We use mass spectrometry and site-directed mutagenesis to identify major sites of ADA3 acetylated by GCN5 and p300. Acetylation-defective mutants are capable of interacting with HATs and other components of HAT complexes but are deficient in their ability to restore ADA3-dependent global or locus-specific histone acetylation marks and cell proliferation in Ada3-deleted murine embryonic fibroblasts (MEFs). Given the key importance of ADA3-containing HAT complexes in the regulation of various biological processes, including the cell cycle, our study presents a novel mechanism to regulate the function of these complexes through dynamic ADA3 acetylation. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Relay selection in underlay cognitive networks with fixed transmission power nodes

KAUST Repository

Hussain, Syed Imtiaz

2013-07-31

Underlay cognitive networks operate simultaneously with primary networks satisfying stringent interference constraints, which reduces their transmission power and coverage area. To reach remote destinations, secondary sources use relaying techniques. Selecting the best relay among the available ones is a well known technique. Recently, selective cooperation is investigated in cognitive networks where the secondary nodes can adapt their transmission power to always satisfy the interference threshold. In this paper, we investigate a situation where the secondary nodes have a fixed transmission power and may violate the interference threshold. We present two relay selection schemes; the first one excludes the relays not satisfying the interference constraint and then picks up a relay from the remaining ones that can provide the maximum signal-to-noise ratio (SNR). The other scheme uses a quotient of the relay link SNR and the interference from the relay to the primary user and optimizes it to maximise the relay link SNR. We derive closed form expressions for outage probability, bit error rate, channel capacity and diversity of the system for both schemes by using tight approximations. We also study mutual effects of interference. Simulation results confirm the analytical results and reveal that the relay selection is feasible at low SNRs. Copyright © 2013 John Wiley & Sons, Ltd.

Acetylation dynamics and stoichiometry in Saccharomyces cerevisiae

DEFF Research Database (Denmark)

Weinert, Brian Tate; Iesmantavicius, Vytautas; Moustafa, Tarek

2014-01-01

Lysine acetylation is a frequently occurring posttranslational modification; however, little is known about the origin and regulation of most sites. Here we used quantitative mass spectrometry to analyze acetylation dynamics and stoichiometry in Saccharomyces cerevisiae. We found that acetylation...

Bilayer Protograph Codes for Half-Duplex Relay Channels

Science.gov (United States)

Divsalar, Dariush; VanNguyen, Thuy; Nosratinia, Aria

2013-01-01

Direct to Earth return links are limited by the size and power of lander devices. A standard alternative is provided by a two-hops return link: a proximity link (from lander to orbiter relay) and a deep-space link (from orbiter relay to Earth). Although direct to Earth return links are limited by the size and power of lander devices, using an additional link and a proposed coding for relay channels, one can obtain a more reliable signal. Although significant progress has been made in the relay coding problem, existing codes must be painstakingly optimized to match to a single set of channel conditions, many of them do not offer easy encoding, and most of them do not have structured design. A high-performing LDPC (low-density parity-check) code for the relay channel addresses simultaneously two important issues: a code structure that allows low encoding complexity, and a flexible rate-compatible code that allows matching to various channel conditions. Most of the previous high-performance LDPC codes for the relay channel are tightly optimized for a given channel quality, and are not easily adapted without extensive re-optimization for various channel conditions. This code for the relay channel combines structured design and easy encoding with rate compatibility to allow adaptation to the three links involved in the relay channel, and furthermore offers very good performance. The proposed code is constructed by synthesizing a bilayer structure with a pro to graph. In addition to the contribution to relay encoding, an improved family of protograph codes was produced for the point-to-point AWGN (additive white Gaussian noise) channel whose high-rate members enjoy thresholds that are within 0.07 dB of capacity. These LDPC relay codes address three important issues in an integrative manner: low encoding complexity, modular structure allowing for easy design, and rate compatibility so that the code can be easily matched to a variety of channel conditions without extensive

Implementation of a Relay Coordination System for the Mars Network

Science.gov (United States)

Allard, Daniel A.

2010-01-01

Mars network relay operations involve the coordination of lander and orbiter teams through long-term and short-term planning, tactical changes and post-pass analysis. Much of this coordination is managed through email traffic and point-to-point file data exchanges. It is often difficult to construct a complete and accurate picture of the relay situation at any given moment, as there is no centralized store of correlated relay data. The Mars Relay Operations Service (MaROS) is being implemented to address the problem of relay coordination for current and next-generation relay missions. The service is provided for the purpose of coordinating communications sessions between landed spacecraft assets and orbiting spacecraft assets at Mars. The service centralizes a set of functions previously distributed across multiple spacecraft operations teams, and as such greatly improves visibility into the end-to-end strategic coordination process. Most of the process revolves around the scheduling of communications sessions between the spacecraft during periods of time when a landed asset on Mars is geometrically visible by an orbiting spacecraft. These "relay" sessions are used to transfer data both to and from the landed asset via the orbiting asset on behalf of Earth-based spacecraft operators. This paper will discuss the relay coordination problem space, overview the architecture and design selected to meet system requirements, and describe the first phase of system implementation

Screening test of relays used under pressurized sulfur hexafluoride (SF6)

International Nuclear Information System (INIS)

Kutsukake, Kenichi; Matsuda, Makoto; Hanashima, Susumu; Obara, Kenjiro

2008-01-01

Many measurement and control devices inside of a high voltage terminal of the JAEA-Tokai tandem accelerator are operated under pressurized sulfur hexafluoride gas (SF 6 ) of 0.5 MPa. This screening test has been carried out to select a relay, which is usable under the pressurized SF 6 for turn on and off a large current of the devices, from commercial relays used in the atmospheric condition. Four kinds of relays were tested: electromechanical relay (EMR), magnet contactor (MAG), solid-state relay (SSR) and hybrid relay (HYB). Temperature and appearance changes of the relay were collected as measurement items. In addition, a reason of contact trouble of the relays was considered from the results of qualitative elementary analysis and observation of the contact surface using the EDS (energy-dispersive X-ray spectroscopy) and the SEM (scanning electron microscope). As a result, the EMR and the MAG showed irregular contact in spite of input voltage and electric current had fed to an operational coil of the relay normally. It is caused by the sulfide or fluoride compounds, which were formed by chemical reaction between metals and sulfur or hydrogen fluoride due to dissociation of SF 6 in electric arcs. On the other hand, the performance of the SSR and the HYB is better than the EMR and the MAG, and it was found that these relays are available in the pressurized SF 6 of 0.5MPa in spite of the standard specification. (author)

Relay-based information broadcast in complex networks

Science.gov (United States)

Fan, Zhongyan; Han, Zeyu; Tang, Wallace K. S.; Lin, Dong

2018-04-01

Information broadcast (IB) is a critical process in complex network, usually accomplished by flooding mechanism. Although flooding is simple and no prior topological information is required, it consumes a lot of transmission overhead. Another extreme is the tree-based broadcast (TB), for which information is disseminated via a spanning tree. It achieves the minimal transmission overhead but the maintenance of spanning tree for every node is an obvious obstacle for implementation. Motivated by the success of scale-free network models for real-world networks, in this paper, we investigate the issues in IB by considering an alternative solution in-between these two extremes. A novel relay-based broadcast (RB) mechanism is proposed by employing a subset of nodes as relays. Information is firstly forwarded to one of these relays and then re-disseminated to others through the spanning tree whose root is the relay. This mechanism provides a trade-off solution between flooding and TB. On one hand, it saves up a lot of transmission overhead as compared to flooding; on the other hand, it costs much less resource for maintenance than TB as only a few spanning trees are needed. Based on two major criteria, namely the transmission overhead and the convergence time, the effectiveness of RB is confirmed. The impacts of relay assignment and network structures on performance are also studied in this work.

Cooperative relay-based multicasting for energy and delay minimization

KAUST Repository

Atat, Rachad

2012-08-01

Relay-based multicasting for the purpose of cooperative content distribution is studied. Optimized relay selection is performed with the objective of minimizing the energy consumption or the content distribution delay within a cluster of cooperating mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles that were not able to receive the multicast data. Both schemes show significant superiority compared to the non-cooperative scenarios, in terms of energy consumption and delay reduction. © 2012 IEEE.

CMOS-NEMS Copper Switches Monolithically Integrated Using a 65 nm CMOS Technology

Directory of Open Access Journals (Sweden)

Jose Luis Muñoz-Gamarra

2016-02-01

Full Text Available This work demonstrates the feasibility to obtain copper nanoelectromechanical (NEMS relays using a commercial complementary metal oxide semiconductor (CMOS technology (ST 65 nm following an intra CMOS-MEMS approach. We report experimental demonstration of contact-mode nano-electromechanical switches obtaining low operating voltage (5.5 V, good ION/IOFF (103 ratio, abrupt subthreshold swing (4.3 mV/decade and minimum dimensions (3.50 μm × 100 nm × 180 nm, and gap of 100 nm. With these dimensions, the operable Cell area of the switch will be 3.5 μm (length × 0.2 μm (100 nm width + 100 nm gap = 0.7 μm2 which is the smallest reported one using a top-down fabrication approach.

Secure relay selection based on learning with negative externality in wireless networks

Science.gov (United States)

Zhao, Caidan; Xiao, Liang; Kang, Shan; Chen, Guiquan; Li, Yunzhou; Huang, Lianfen

2013-12-01

In this paper, we formulate relay selection into a Chinese restaurant game. A secure relay selection strategy is proposed for a wireless network, where multiple source nodes send messages to their destination nodes via several relay nodes, which have different processing and transmission capabilities as well as security properties. The relay selection utilizes a learning-based algorithm for the source nodes to reach their best responses in the Chinese restaurant game. In particular, the relay selection takes into account the negative externality of relay sharing among the source nodes, which learn the capabilities and security properties of relay nodes according to the current signals and the signal history. Simulation results show that this strategy improves the user utility and the overall security performance in wireless networks. In addition, the relay strategy is robust against the signal errors and deviations of some user from the desired actions.

Proof-of-Work as Anonymous Micropayment: Rewarding a Tor Relay

OpenAIRE

Biryukov, Alex; Pustogarov, Ivan

2015-01-01

In this paper we propose a new micropayments scheme which can be used to reward Tor relay operators. Tor clients do not pay Tor relays with electronic cash directly but submit proof of work shares which the relays can resubmit to a crypto-currency mining pool. Relays credit users who submit shares with tickets that can later be used to purchase improved service. Both shares and tickets when sent over Tor circuits are anonymous. The analysis of the crypto-currencies market prices shows that th...

Error-rate performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel

2011-09-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path can be considered unusable, and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We first derive the exact statistics of each hop, in terms of probability density function (PDF). Then, the PDFs are used to determine accurate closed form expressions for end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation where the detector may use maximum ration combining (MRC) or selection combining (SC). Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over linear network (LN) architecture and considering Rayleigh fading channels. © 2011 IEEE.

An RSS based location estimation technique for cognitive relay networks

KAUST Repository

Qaraqe, Khalid A.

2010-11-01

In this paper, a received signal strength (RSS) based location estimation method is proposed for a cooperative wireless relay network where the relay is a cognitive radio. We propose a method for the considered cognitive relay network to determine the location of the source using the direct and the relayed signal at the destination. We derive the Cramer-Rao lower bound (CRLB) expressions separately for x and y coordinates of the location estimate. We analyze the effects of cognitive behaviour of the relay on the performance of the proposed method. We also discuss and quantify the reliability of the location estimate using the proposed technique if the source is not stationary. The overall performance of the proposed method is presented through simulations. ©2010 IEEE.

CERN’s annual relay a runaway success

CERN Document Server

Klaus Hanke for the CERN Running Club

2016-01-01

With a record participation of 128 teams of six runners each, this year’s CERN Relay Race took place on 19 May on the Meyrin site.   One of the many winning teams from the 2016 relay race. (Image: Sophia Bennett/CERN) With a record participation of 128 teams and 768 runners, this year’s CERN Relay Race took place on 19 May on the Meyrin site. The teams were mainly composed of CERN staff or contractors working on the CERN site.  A few external teams took also part in the race. Times ranged from 10 min 19 s to over 18 min. The Running Club website now has both the results, and the photos from race day. The CERN Relay Race is jointly organised every year by the CERN Running Club and the Staff Association. It is a tradition that is appreciated by many as a team building, rather than a competitive event. The CERN Running Club wishes to thank all runners and all volunteers for making this event a success.

Acetylation and characterization of banana (Musa paradisiaca) starch.

Science.gov (United States)

Bello-Pérez, L A; Contreras-Ramos, S M; Jìmenez-Aparicio, A; Paredes-López, O

2000-01-01

Banana native starch was acetylated and some of its functional properties were evaluated and compared to corn starch. In general, acetylated banana starch presented higher values in ash, protein and fat than corn acetylated starch. The modified starches had minor tendency to retrogradation assessed as % transmittance of starch pastes. At high temperature acetylated starches presented a water retention capacity similar to their native counterpart. The acetylation considerably increased the solubility of starches, and a similar behavior was found for swelling power. When freeze-thaw stability was studied, acetyl banana starch drained approximately 60% of water in the first and second cycles, but in the third and fourth cycles the percentage of separated water was low. However, acetyl corn starch showed lower freeze-thaw stability than the untreated sample. The modification increased the viscosity of banana starch pastes.

Securing Relay Networks with Artificial Noise: An Error Performance-Based Approach

Directory of Open Access Journals (Sweden)

Ying Liu

2017-07-01

Full Text Available We apply the concept of artificial and controlled interference in a two-hop relay network with an untrusted relay, aiming at enhancing the wireless communication secrecy between the source and the destination node. In order to shield the square quadrature amplitude-modulated (QAM signals transmitted from the source node to the relay, the destination node designs and transmits artificial noise (AN symbols to jam the relay reception. The objective of our considered AN design is to degrade the error probability performance at the untrusted relay, for different types of channel state information (CSI at the destination. By considering perfect knowledge of the instantaneous CSI of the source-to-relay and relay-to-destination links, we first present an analytical expression for the symbol error rate (SER performance at the relay. Based on the assumption of an average power constraint at the destination node, we then derive the optimal phase and power distribution of the AN that maximizes the SER at the relay. Furthermore, we obtain the optimal AN design for the case where only statistical CSI is available at the destination node. For both cases, our study reveals that the Gaussian distribution is generally not optimal to generate AN symbols. The presented AN design takes into account practical parameters for the communication links, such as QAM signaling and maximum likelihood decoding.

Efficient incremental relaying for packet transmission over fading channels

KAUST Repository

Fareed, Muhammad Mehboob

2014-07-01

In this paper, we propose a novel relaying scheme for packet transmission over fading channels, which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from the destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying (EIR) scheme with both amplify and forward and decode and forward relaying. We compare the performance of the EIR scheme with the threshold-based incremental relaying (TIR) scheme. It is shown that the efficiency of the TIR scheme is better for lower values of the threshold. However, the efficiency of the TIR scheme for higher values of threshold is outperformed by the EIR. In addition, three new threshold-based adaptive EIR are devised to further improve the efficiency of the EIR scheme. We calculate the packet error rate and the efficiency of these new schemes to provide the analytical insight. © 2014 IEEE.

Relay discovery and selection for large-scale P2P streaming.

Directory of Open Access Journals (Sweden)

Chengwei Zhang

Full Text Available In peer-to-peer networks, application relays have been commonly used to provide various networking services. The service performance often improves significantly if a relay is selected appropriately based on its network location. In this paper, we studied the location-aware relay discovery and selection problem for large-scale P2P streaming networks. In these large-scale and dynamic overlays, it incurs significant communication and computation cost to discover a sufficiently large relay candidate set and further to select one relay with good performance. The network location can be measured directly or indirectly with the tradeoffs between timeliness, overhead and accuracy. Based on a measurement study and the associated error analysis, we demonstrate that indirect measurements, such as King and Internet Coordinate Systems (ICS, can only achieve a coarse estimation of peers' network location and those methods based on pure indirect measurements cannot lead to a good relay selection. We also demonstrate that there exists significant error amplification of the commonly used "best-out-of-K" selection methodology using three RTT data sets publicly available. We propose a two-phase approach to achieve efficient relay discovery and accurate relay selection. Indirect measurements are used to narrow down a small number of high-quality relay candidates and the final relay selection is refined based on direct probing. This two-phase approach enjoys an efficient implementation using the Distributed-Hash-Table (DHT. When the DHT is constructed, the node keys carry the location information and they are generated scalably using indirect measurements, such as the ICS coordinates. The relay discovery is achieved efficiently utilizing the DHT-based search. We evaluated various aspects of this DHT-based approach, including the DHT indexing procedure, key generation under peer churn and message costs.

Optimal Coordination of Distance and Directional Overcurrent Relays Considering Different Network Topologies

OpenAIRE

Y. Damchi; J. Sadeh; H. Rajabi Mashhadi

2015-01-01

Most studies in relay coordination have focused solely on coordination of overcurrent relays while distance relays are used as the main protection of transmission lines. Since, simultaneous coordination of these two types of relays can provide a better protection, in this paper, a new approach is proposed for simultaneous coordination of distance and directional overcurrent relays (D&DOCRs). Also, pursued by most of the previously published studies, the settings of D&DOCRs are usually determi...

Characterization and mode of action of two acetyl xylan esterases from Chrysosporium lucknowense C1 active towards acetylated xylans

NARCIS (Netherlands)

Pouvreau, L.A.M.; Jonathan, M.C.; Kabel, M.A.; Hinz, S.W.A.; Gruppen, H.; Schols, H.A.

2011-01-01

Two novel acetyl xylan esterases, Axe2 and Axe3, from Chrysosporium lucknowense (C1), belonging to the carbohydrate esterase families 5 and 1, respectively, were purified and biochemically characterized. Axe2 and Axe3 are able to hydrolyze acetyl groups both from simple acetylated

Microcomputer relay regulator in the CAMAC standard

International Nuclear Information System (INIS)

Nikolaev, V.P.

1984-01-01

The digital relay regulator is developed on the base of the KM001 microcomputer and KK06 controller for automatic control ob ects with transfer functions describing a broad class of systems using actuating motors (stabilitation, follow-up systems). The CAMAC relay-unit realizes the regulation law and provides the possibility to control analogous values by 8 channels

Coordination of Regenerative Relays and Direct Users in Wireless Cellular Networks

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar

2011-01-01

The area of wireless cooperation/relaying has recently been significantly enriched by the ideas of wireless network coding (NC), which bring substantial gains in spectral efficiency. These gains have mainly been demonstrated in scenarios with two-way relaying. Inspired by the ideas of wireless NC......, recently we have proposed techniques for coordinated direct/relay (CDR) transmissions. These techniques embrace the interference among the communication flows to/from direct and relayed users, leveraging on the fact that the interference can be subsequently canceled. Hence, by allowing simultaneous...... transmissions, spectral efficiency is increased. In our prior work, we have considered CDR with non-regenerative relay that uses Amplify-and-Forward (AF). In this paper we consider the case of regenerative Decode-and-Forward (DF) relay. This refers also to joint decoding of the interfering flows received over...

Admission Control Threshold in Cellular Relay Networks with Power Adjustment

Directory of Open Access Journals (Sweden)

Lee Ki-Dong

2009-01-01

Full Text Available Abstract In the cellular network with relays, the mobile station can benefit from both coverage extension and capacity enhancement. However, the operation complexity increases as the number of relays grows up. Furthermore, in the cellular network with cooperative relays, it is even more complex because of an increased dimension of signal-to-noise ratios (SNRs formed in the cooperative wireless transmission links. In this paper, we propose a new method for admission capacity planning in a cellular network using a cooperative relaying mechanism called decode-and-forward. We mathematically formulate the dropping ratio using the randomness of "channel gain." With this, we formulate an admission threshold planning problem as a simple optimization problem, where we maximize the accommodation capacity (in number of connections subject to two types of constraints. (1 A constraint that the sum of the transmit powers of the source node and relay node is upper-bounded where both nodes can jointly adjust the transmit power. (2 A constraint that the dropping ratio is upper-bounded by a certain threshold value. The simplicity of the problem formulation facilitates its solution in real-time. We believe that the proposed planning method can provide an attractive guideline for dimensioning a cellular relay network with cooperative relays.

Implementation of a microcomputer based distance relay for parallel transmission lines

International Nuclear Information System (INIS)

Phadke, A.G.; Jihuang, L.

1986-01-01

Distance relaying for parallel transmission lines is a difficult application problem with conventional phase and ground distance relays. It is known that for cross-country faults involving dissimilar phases and ground, three phase tripping may result. This paper summarizes a newly developed microcomputer based relay which is capable of classifying the cross-country fault correctly. The paper describes the principle of operation and results of laboratory tests of this relay

Performance Analysis of Selective Decode-and-Forward Multinode Incremental Relaying with Maximal Ratio Combining

KAUST Repository

Hadjtaieb, Amir

2013-09-12

In this paper, we propose an incremental multinode relaying protocol with arbitrary N-relay nodes that allows an efficient use of the channel spectrum. The destination combines the received signals from the source and the relays using maximal ratio Combining (MRC). The transmission ends successfully once the accumulated signal-to-noise ratio (SNR) exceeds a predefined threshold. The number of relays participating in the transmission is adapted to the channel conditions based on the feedback from the destination. The use of incremental relaying allows obtaining a higher spectral efficiency. Moreover, the symbol error probability (SEP) performance is enhanced by using MRC at the relays. The use of MRC at the relays implies that each relay overhears the signals from the source and all previous relays and combines them using MRC. The proposed protocol differs from most of existing relaying protocol by the fact that it combines both incremental relaying and MRC at the relays for a multinode topology. Our analyses for a decode-and-forward mode show that: (i) compared to existing multinode relaying schemes, the proposed scheme can essentially achieve the same SEP performance but with less average number of time slots, (ii) compared to schemes without MRC at the relays, the proposed scheme can approximately achieve a 3 dB gain.

Spectral efficiency enhancement with interference cancellation for wireless relay network

DEFF Research Database (Denmark)

Yomo, Hiroyuki; De Carvalho, Elisabeth

The introduction of relaying into wireless communication system for coverage enhancement can cause severe decrease of spectral efficiency due to the requirement on extra radio resource. In this paper, we propose a method to increase spectral efficiency in such a wireless relay network by employing...... an interference cancellation technique. We focus on a typical scenario of relaying in a cellular system, where a mobile station (MS) requires the help of a relay station (RS) to communicate with the base station (BS). In such a case, interference cancellation can be used to achieve a small reuse distance...... of identical radio resource. We analyze a simple scenario with BS, single RS, and 2 MSs, and show that the proposed method has significant potential to enhance spectral efficiency in wireless relay networks....

Resource allocation for relay assisted cognitive radio networks

KAUST Repository

Zafar, Ammar; Alouini, Mohamed-Slim; Chen, Yunfei; Radaydeh, Redha M.

2012-01-01

transmission power and the relay transmission power. Numerical results show that the optimal sensing time is dependent on the primary user's signal-to-noise-ratio (SNR). They also show that SCR increases with increase in the number of relays. © 2012 IEEE.

Protective relaying of power systems using mathematical morphology

CERN Document Server

Wu, QH; Ji, TY

2009-01-01

Discusses the development of novel protective relaying algorithms, using Mathematical Morphology (MM). This book introduces the fundamental principles of MM, and brings together the applications of MM to develop different protective relaying algorithms for the protection of a variety of power system components.

NetAcet: prediction of N-terminal acetylation sites

DEFF Research Database (Denmark)

Kiemer, Lars; Bendtsen, Jannick Dyrløv; Blom, Nikolaj

2005-01-01

Summary: We present here a neural network based method for prediction of N-terminal acetylation-by far the most abundant post-translational modification in eukaryotes. The method was developed on a yeast dataset for N-acetyltransferase A (NatA) acetylation, which is the type of N-acetylation for ......Summary: We present here a neural network based method for prediction of N-terminal acetylation-by far the most abundant post-translational modification in eukaryotes. The method was developed on a yeast dataset for N-acetyltransferase A (NatA) acetylation, which is the type of N...

A Stochastic Geometry Approach to Full-Duplex MIMO Relay Network

Directory of Open Access Journals (Sweden)

Mhd Nour Hindia

2018-01-01

Full Text Available Cellular networks are extensively modeled by placing the base stations on a grid, with relays and destinations being placed deterministically. These networks are idealized for not considering the interferences when evaluating the coverage/outage and capacity. Realistic models that can overcome such limitation are desirable. Specifically, in a cellular downlink environment, the full-duplex (FD relaying and destination are prone to interferences from unintended sources and relays. However, this paper considered two-hop cellular network in which the mobile nodes aid the sources by relaying the signal to the dead zone. Further, we model the locations of the sources, relays, and destination nodes as a point process on the plane and analyze the performance of two different hops in the downlink. Then, we obtain the success probability and the ergodic capacity of the two-hop MIMO relay scheme, accounting for the interference from all other adjacent cells. We deploy stochastic geometry and point process theory to rigorously analyze the two-hop scheme with/without interference cancellation. These attained expressions are amenable to numerical evaluation and are corroborated by simulation results.

Minimax robust relay selection based on uncertain long-term CSI

KAUST Repository

Nisar, Muhammad Danish

2014-02-01

Cooperative communications via multiple relay nodes is known to provide the benefits of increase diversity and coverage. Simultaneous transmission via multiple relays, however, requires strong coordination between nodes either in terms of slot-based transmission or distributed space-time (ST) code implementation. Dynamically selecting a single best relay out of multiple relays and then using it alone for cooperative transmission alleviates the need for this strong coordination while still reaping the benefits of increased diversity and coverage. In this paper, we consider the design of relay selection (RS) under an imperfect knowledge of long-term channel state information (CSI) at the relay nodes, and we pursue minimax optimization to arrive at a robust RS approach that promises the best guarantee on the worst-case end-to-end signal-to-noise ratio (SNR). We provide some intuitive examples and extensive simulation results, not only in terms of worst-case SNR performance but also in terms of average bit-error-rate (BER) performance, to demonstrate the benefits of the proposed minimax robust RS scheme. © 2013 IEEE.

Interference alignment for degrees of freedom improvement in 3-relay half-duplex systems

KAUST Repository

Park, Seongho

2011-12-01

In a half-duplex relaying, the capacity pre-log factor is a major drawback in spectral efficiency. This paper proposes a linear precoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can eliminate the inter-relay interference resulted from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2011 IEEE.

Overlay cognitive radio systems with adaptive two-way relaying

KAUST Repository

Hyadi, Amal

2013-12-01

In this paper, we propose a spectrum sharing mechanism with a two-phase two-way relaying protocol for an overlay cognitive network. The system comprises two primary users (PUs) and two secondary users (SUs). One of the SUs acts as a relay for the PUs and gains spectrum sharing as long as he respects outage probability constraints of the primary system. Moreover, we consider that the relaying node performs an optimal power allocation scheme that minimizes the outage performance of the secondary receiver. Closed form expressions for the outage probability are derived for the cases of Decode-and-Forward (DF), Amplify-and-Forward (AF), and adaptive relaying. Numerical simulations are presented to illustrate and compare the obtained results. © 2013 IEEE.

Effect of Drying Pretreatment on the Acetylation of Nanofibrillated Cellulose

Directory of Open Access Journals (Sweden)

Vesna Zepič

2015-10-01

Full Text Available The aim of this study was to evaluate the effect of different morphologies of solvent-exchanged (NFCSE, spray-dried (NFCSD, and freeze-dried (NFCFD nano-fibrillated cellulose on the susceptibility to surface modification with the acetic anhydride/pyridine system. The degree of substitution (DS, morphology, degree of crystallinity (Icr, hydrophobicity, and thermal stability of acetylated products were examined. Acetylated NFCSD and NFCFD had higher DS than acetylated NFCSE, suggesting that drying pre-treatment increased the susceptibility of NFC for acetylation. The morphology of acetylated NFCFD and NFCSD with higher DS was different from unmodified samples, while that of NFCSE was not affected by acetylation. Microspheres of acetylated NFCSD started to dissolve when the highest DS was reached. As opposed to unmodified NFCFD, the nanofibrillar units of acetylated NFCFD became individualised at lower DS. Acetylated samples had lower Icr than the unmodified samples. A significant increase in the contact angle was observed at higher DS of acetylated NFC samples. Acetylation markedly elevated the thermal stability of the acetylated NFC samples.

Structures of the NLRP14 pyrin domain reveal a conformational switch mechanism regulating its molecular interactions

International Nuclear Information System (INIS)

Eibl, Clarissa; Hessenberger, Manuel; Wenger, Julia; Brandstetter, Hans

2014-01-01

Pyrin domains (PYDs) recruit downstream effector molecules in NLR signalling. A specific charge-relay system suggests a the formation of a signalling complex involving a PYD dimer. The cytosolic tripartite NLR receptors serve as important signalling platforms in innate immunity. While the C-terminal domains act as sensor and activation modules, the N-terminal death-like domain, e.g. the CARD or pyrin domain, is thought to recruit downstream effector molecules by homotypic interactions. Such homotypic complexes have been determined for all members of the death-domain superfamily except for pyrin domains. Here, crystal structures of human NLRP14 pyrin-domain variants are reported. The wild-type protein as well as the clinical D86V mutant reveal an unexpected rearrangement of the C-terminal helix α6, resulting in an extended α5/6 stem-helix. This reordering mediates a novel symmetric pyrin-domain dimerization mode. The conformational switching is controlled by a charge-relay system with a drastic impact on protein stability. How the identified charge relay allows classification of NLRP receptors with respect to distinct recruitment mechanisms is discussed

Best relay selection using SNR and interference quotient for underlay cognitive networks

KAUST Repository

Hussain, Syed Imtiaz

2012-06-01

Cognitive networks in underlay settings operate simultaneously with the primary networks satisfying stringent interference limits. This condition forces them to operate with low transmission powers and confines their area of coverage. In an effort to reach remote destinations, underlay cognitive sources make use of relaying techniques. Selecting the best relay among those who are ready to cooperate is different in underlay settings than traditional non-cognitive networks. In this paper, we present a relay selection scheme which uses the quotient of the relay link signal to noise ratio (SNR) and the interference generated from the relay to the primary user to choose the best relay. The proposed scheme optimizes this quotient in a way to maximize the relay link SNR above a certain value whereas the interference is kept below a defined threshold. We derive closed expressions for the outage probability and bit error probability of the system incorporating this scheme. Simulation results confirm the validity of the analytical results and reveal that the relay selection in cognitive environment is feasible in low SNR regions. © 2012 IEEE.

Adaptive transmission based on multi-relay selection and rate-compatible LDPC codes

Science.gov (United States)

Su, Hualing; He, Yucheng; Zhou, Lin

2017-08-01

In order to adapt to the dynamical changeable channel condition and improve the transmissive reliability of the system, a cooperation system of rate-compatible low density parity check (RC-LDPC) codes combining with multi-relay selection protocol is proposed. In traditional relay selection protocol, only the channel state information (CSI) of source-relay and the CSI of relay-destination has been considered. The multi-relay selection protocol proposed by this paper takes the CSI between relays into extra account in order to obtain more chances of collabration. Additionally, the idea of hybrid automatic request retransmission (HARQ) and rate-compatible are introduced. Simulation results show that the transmissive reliability of the system can be significantly improved by the proposed protocol.

Frame Allocation and Scheduling for Relay Networks in the LTE Advanced Standard

OpenAIRE

Roth, Stefan

2010-01-01

The use of relays is seen as a promising way to extend cell coverage and increase rates in LTE Advanced networks. Instead of increasing the number of base stations (BS), relays with lower cost could provide similar gains. A relay will have a wireless link to the closest BS as only connection to the core network and will cover areas close to the cell edge or other areas with limited rates. Performing transmissions in several hops (BS-relay & relay-user) requires more radio resources than u...

77 FR 16435 - Transmission Relay Loadability Reliability Standard

Science.gov (United States)

2012-03-21

... conditions on all applicable transmission lines and transformers. I. Background A. Relay Protection Systems 2... and a power swing. If a power swing is detected, the protection system, ``blocks,'' or prevents the... to the reliability of the Bulk-Power System by requiring load-responsive phase protection relay...

76 FR 58424 - Transmission Relay Loadability Reliability Standard

Science.gov (United States)

2011-09-21

... distribution providers to set load-responsive phase protection relays according to specific criteria to ensure...-part R.1.10 allows transmission owners, generation owners and distribution providers to set transformer.... Thus, requiring that transformer fault protection relays are set to not expose the transformer to a...

Development of a Relay Performance Web Tool for the Mars Network

Science.gov (United States)

Allard, Daniel A.; Edwards, Charles D.

2009-01-01

Modern Mars surface missions rely upon orbiting spacecraft to relay communications to and from Earth systems. An important component of this multi-mission relay process is the collection of relay performance statistics supporting strategic trend analysis and tactical anomaly identification and tracking.

Micro-relay technology for energy-efficient integrated circuits

CERN Document Server

Kam, Hei

2015-01-01

This book describes the design of relay-based circuit systems from device fabrication to circuit micro-architectures. This book is ideal for both device engineers as well as circuit system designers and highlights the importance of co-design across design hierarchies when optimizing system performance (in this case, energy-efficiency). This book is ideal for researchers and engineers focused on semiconductors, integrated circuits, and energy efficient electronics. This book also: ·         Covers microsystem fabrication, MEMS device design, circuit design, circuit micro-architecture, and CAD ·         Describes work previously done in the field and also lays the groundwork and criteria for future energy-efficient device and system design ·         Maximizes reader insights into the design and modeling of micro-relay, micro-relay reliability, integrated circuit design with micro-relays, and more

Linear Processing Design of Amplify-and-Forward Relays for Maximizing the System Throughput

Directory of Open Access Journals (Sweden)

Qiang Wang

2018-01-01

Full Text Available In this paper, firstly, we study the linear processing of amplify-and-forward (AF relays for the multiple relays multiple users scenario. We regard all relays as one special “relay”, and then the subcarrier pairing, relay selection and channel assignment can be seen as a linear processing of the special “relay”. Under fixed power allocation, the linear processing of AF relays can be regarded as a permutation matrix. Employing the partitioned matrix, we propose an optimal linear processing design for AF relays to find the optimal permutation matrix based on the sorting of the received SNR over the subcarriers from BS to relays and from relays to users, respectively. Then, we prove the optimality of the proposed linear processing scheme. Through the proposed linear processing scheme, we can obtain the optimal subcarrier paring, relay selection and channel assignment under given power allocation in polynomial time. Finally, we propose an iterative algorithm based on the proposed linear processing scheme and Lagrange dual domain method to jointly optimize the joint optimization problem involving the subcarrier paring, relay selection, channel assignment and power allocation. Simulation results illustrate that the proposed algorithm can achieve a perfect performance.

A novel micro/nano 1 × 4 mechanical optical switch

Science.gov (United States)

Lin, Wu-Lang; Fan, Kuang-Chao; Chiang, Li-Hung; Yang, Yao-Joe; Kuo, Wen-Cheng; Chung, Tien-Tung

2006-07-01

This paper presents the design, fabrication and testing of a novel 1 × 4 mechanical optical switch, whose components are fabricated by precision machining and MEMS technologies. The switch uses two relays as the two actuators whose switching direction is perpendicular to each other by an orthogonal arrangement. We adopt a direct fiber-to-fiber principle that aligns the input fiber directly to four output fibers. This configuration eliminates the use of traditional parts such as collimators, turning mirrors or prisms. In addition, due to the use of a fiber holder, the fiber position errors could be reduced to less than 0.27 µm using the two-stage geometry error reduction principle. We have successfully developed a simple and low-cost switch, which performs like most of the 1 × 4 mechanical optical switches that dominate the optics communications market. The advantages of our switch are a small size (20 × 20 × 25 mm3), low cost, high reliability, and the latching function does not need external force for maintaining the state. The experimental results showed that the insertion losses of the four channels are ch1: 0.68 dB, ch2: 1.49 dB, ch3: 0.71 dB and ch4: 0.97 dB. The switching time is 5 ms, the crosstalk <=80 dB. The reliability tests of the insertion loss after 10 000 cycles in four channels yield ch1: 1.67 dB, ch2: 1.63 dB, ch3: 0.75 dB and ch4: 0.98 dB. The size and the cost of our 1 × 4 mechanical optical switch are only about 1/5-1/10 and 1/10 of the series-connect-type and prism-type switches, respectively.

A study on Relay Effect via Magnetic Resonant Coupling for Wireless Power Transfer

Directory of Open Access Journals (Sweden)

Rashid N.A.

2016-01-01

Full Text Available Wireless power transfer (WPT transmits electrical energy from a power source to an electrical load wirelessly or without any conductors. The capability of WPT to transmit the energy is limited. Therefore, a relay was introduced to increase the distance of the WPT capabilities. The effect of the relay has been investigated to extend the energy transfer distance. The effect of relay was demonstrated by placing a relay coil between transmitter and receiver, relay biased to transmitter and placing two relay coils in the designed system. Experimental results are provided to prove the concept of the relay effect. The power transmission efficiency can be achieved up to 75% at 1 meter distance.

Structural aspects of the solvation shell of lysine and acetylated lysine: A Car-Parrinello and classical molecular dynamics investigation

International Nuclear Information System (INIS)

Carnevale, V.; Raugei, S.

2009-01-01

Lysine acetylation is a post-translational modification, which modulates the affinity of protein-protein and/or protein-DNA complexes. Its crucial role as a switch in signaling pathways highlights the relevance of charged chemical groups in determining the interactions between water and biomolecules. A great effort has been recently devoted to assess the reliability of classical molecular dynamics simulations in describing the solvation properties of charged moieties. In the spirit of these investigations, we performed classical and Car-Parrinello molecular dynamics simulations on lysine and acetylated-lysine in aqueous solution. A comparative analysis between the two computational schemes is presented with a focus on the first solvation shell of the charged groups. An accurate structural analysis unveils subtle, yet statistically significant, differences which are discussed in connection to the significant electronic density charge transfer occurring between the solute and the surrounding water molecules.

The impact of SFCL and SMES integration on the distance relay

Energy Technology Data Exchange (ETDEWEB)

Yang, Jun, E-mail: JYang@whu.edu.cn [School of Electrical Engineering, Wuhan University, Wuhan 430072 (China); Zhang, Liling; Wang, Xinpu; Chen, Lei [School of Electrical Engineering, Wuhan University, Wuhan 430072 (China); Chen, Yanxia [Beijing Electric Power Research Institute, Beijing 100075 (China)

2016-11-15

Highlights: • The impact of SFCL and SMES integration on the circle distance relay is studied. • The detailed models of SFCL and SMES with distance delay are built in MATLAB. • The integration of SFCL and SMES does influence the operation of distance relay. • An improved distance relay to prevent mal-operation is proposed and verified. - Abstract: The superconducting fault current limiter (SFCL) is an ideal short-circuit fault current limiting device that can limit the fault current without any delay and control the voltage drop of the non-fault line. The superconducting magnetic energy storage (SMES) device can exchange the active and reactive power independently, so it is applied broadly to improve power system stability. With SFCL, the low voltage ride-through capability of SMES can be enhanced as well as its MW and MJ capacities. The distance relay is a key electrical apparatus that will trip circuit breakers to protect electrical devices from short circuit faults. Due to the application of SFCL and SMES integration, the voltage and current in power grid will change accordingly, and the operation characteristic of distance relay may be affected. In this paper, the impact of a bridge-type SFCL and SMES integration on the circle distance relay is studied. And simulation results show that the integration of SFCL and SMES does influence the measured impedance of distance relay, which can lead to mal-operation of the circle distance relay. Furthermore, an improved distance relay is proposed and verified.

The impact of SFCL and SMES integration on the distance relay

International Nuclear Information System (INIS)

Yang, Jun; Zhang, Liling; Wang, Xinpu; Chen, Lei; Chen, Yanxia

2016-01-01

Highlights: • The impact of SFCL and SMES integration on the circle distance relay is studied. • The detailed models of SFCL and SMES with distance delay are built in MATLAB. • The integration of SFCL and SMES does influence the operation of distance relay. • An improved distance relay to prevent mal-operation is proposed and verified. - Abstract: The superconducting fault current limiter (SFCL) is an ideal short-circuit fault current limiting device that can limit the fault current without any delay and control the voltage drop of the non-fault line. The superconducting magnetic energy storage (SMES) device can exchange the active and reactive power independently, so it is applied broadly to improve power system stability. With SFCL, the low voltage ride-through capability of SMES can be enhanced as well as its MW and MJ capacities. The distance relay is a key electrical apparatus that will trip circuit breakers to protect electrical devices from short circuit faults. Due to the application of SFCL and SMES integration, the voltage and current in power grid will change accordingly, and the operation characteristic of distance relay may be affected. In this paper, the impact of a bridge-type SFCL and SMES integration on the circle distance relay is studied. And simulation results show that the integration of SFCL and SMES does influence the measured impedance of distance relay, which can lead to mal-operation of the circle distance relay. Furthermore, an improved distance relay is proposed and verified.

Cooperation schemes for rate enhancement in detect-and-forward relay channels

KAUST Repository

Benjillali, Mustapha

2010-05-01

To improve the spectral efficiency of "Detect-and-Forward" (DetF) half-duplex relaying in fading channels, we propose a cooperation scheme where the relay uses a modulation whose order is higher than the one at the source. In a new common framework, we show that the proposed scheme offers considerable gains - in terms of achievable information rates - compared to the conventional DetF relaying schemes for both orthogonal and non-orthogonal source/relay cooperation. This allows us to propose an adaptive cooperation scheme based on the maximization of the information rate at the destination which needs to observe only the average signal-to-noise ratios of direct and relaying links. ©2010 IEEE.

IEEE C37.98-1987: IEEE standard seismic testing of relays

International Nuclear Information System (INIS)

Anon.

1992-01-01

This standard specifies the procedures to be used in the seismic testing of relays used in power system facilities. The standard is concerned with the determination of the seismic fragility level of relays and also gives recommendations for proof testing. The purpose of this standard is to establish procedures for determining the seismic capabilities of protective and auxiliary relays. These procedures employ what has been called fragility testing in IEEE Std 344-1987. To define the conditions for fragility testing of relays, parameters in three separate areas must be specified. In general, they are (1) the electrical settings and inputs to the relay, and other information to define its conditions during the test; (2) the change in state, deviation in operating characteristics or tolerances, or other change of performance of the relay that constitutes failure; (3) the seismic vibration environment to be imposed during the test. Since it is not possible to define the conditions for every conceivable application for all relays, those parameters, which in practice encompass the majority of applications, have been specified in this standard. When the application of the relay is other than as specified under any of (1), (2), and (3), or if it is not practical to apply existing results of fragility tests to that new application, then proof testing must be performed for that new case

IEEE C37.98-1978: IEEE standard seismic testing of relays

International Nuclear Information System (INIS)

Anon.

1992-01-01

This standard specifies the procedures to be used in the seismic testing of relays used in power system facilities. The standard is concerned with the determination of the seismic fragility level of relays and also gives recommendations for proof testing. The purpose of this standard is to establish procedures for determining the seismic capabilities of protective and auxiliary relays. These procedures employ what has been called fragility testing in ANSI/IEEE Std 344-1975, Recommended Practices for Seismic Qualification of Class 1E Equipment for Nuclear Power Generating Stations. In order to define the conditions for fragility testing of relays, parameters in three separate areas must be specified. In general they are: (1) the electrical settings and inputs to the relay, and other information to define its conditions during the test; (2) the change in state, deviation in operating characteristics or tolerances, or other change of performance of the relay which constitutes failure; (3) the seismic vibration environment to be imposed during the test. Since it is not possible to define the conditions for every conceivable application for all relays, those parameters, which in practice encompass the majority of applications, have been specified in this standard. When the application of the relay is other than as specified under any of (1), (2), and (3), or if it is not practical to apply existing results of fragility tests to that new case

Trichoderma reesei CE16 acetyl esterase and its role in enzymatic degradation of acetylated hemicellulose

DEFF Research Database (Denmark)

Biely, Peter; Cziszarava, Maria; Agger, Jane W.

2014-01-01

Results The combined action of GH10 xylanase and acetylxylan esterases (AcXEs) leads to formation of neutral and acidic xylooligosaccharides with a few resistant acetyl groups mainly at their non-reducing ends. We show here that these acetyl groups serve as targets for TrCE16 AcE. The most promin...

Modeling and Simulation of Out of Step Blocking Relay for

Directory of Open Access Journals (Sweden)

Ahmed A. Al Adwani

2013-05-01

Full Text Available  This paper investigates a power swing effect on a distance protection relay performance installed on (HV/EHV transmission line as well as power system stability. A conventional distance relay can’t properly operate under transient stability conditions; therefore, it cause mol-operation, and it will adversely impact on its trip signals. To overcome this problem, the Out Of Step (OOS relay has modeled and simulated to joint with distance relay to supervise and control on its trip signals response. The setting characteristics technique of the OOS based on concentric polygons scheme method to detect power swing under transient stability situation.         This study ia a modeling and simulating using (Maltab\\ Simulink software. A Two relays had been  performed   and  tested  with  two equivalents network connected to ends.      The results of this study showed an activity and reliability of this way to control the distance relay response under a transient stability conditions and it indicated the possibility to find out faults which may occur at period of power swing

STUDI ANALISIS KOORDINASI OVER CURRENT RELAY (OCR) DAN GROUND FAULT RELAY (GFR) PADA RECLOSER DI SALURAN PENYULANG PENEBEL

OpenAIRE

I Dewa Gde Agung Budhi Udiana; I G Dyana Arjana; Tjok Gede Indra Partha

2017-01-01

Short circuit causing over current problem and can might causing interference of the equipment performance such as distribution transformers also causing widespread disruption occurred. In resolving such interference is required as protection system on the distribution system. Seeing all above is needed coordination between the supporting component of the protection system which is consisted of Over Current Relay (OCR) and Ground Fault Relay (GFR). The research was conducted at PT. PLN (Perse...

On the Outage Performance of Full-Duplex Selective Decode-and-Forward Relaying

KAUST Repository

Khafagy, Mohammad Galal

2013-02-25

We evaluate the outage performance in a three-terminal full-duplex relay channel that adopts a selective decode-and-forward protocol, taking relay self-interference into account. Previous work focused on coverage extension scenarios where direct source-destination transmissions are neglected or considered as interference. In this work, we account for the relay self-interference, and exploit the cooperative diversity offered by the independently fading source/relay message replicas that arrive at the destination. We present an approximate, yet accurate, closed-form expression for the end-to-end outage probability that captures their joint effect. With the derived expression in hand, we propose a relay transmit power optimization scheme that only requires the relay knowledge of channel statistics. Finally, we corroborate our analysis with simulations.

Whether and Where to Code in the Wireless Relay Channel

DEFF Research Database (Denmark)

Shi, Xiaomeng; Médard, Muriel; Roetter, Daniel Enrique Lucani

2013-01-01

The throughput benefits of random linear network codes have been studied extensively for wirelined and wireless erasure networks. It is often assumed that all nodes within a network perform coding operations. In energy-constrained systems, however, coding subgraphs should be chosen to control...... the number of coding nodes while maintaining throughput. In this paper, we explore the strategic use of network coding in the wireless packet erasure relay channel according to both throughput and energy metrics. In the relay channel, a single source communicates to a single sink through the aid of a half......-duplex relay. The fluid flow model is used to describe the case where both the source and the relay are coding, and Markov chain models are proposed to describe packet evolution if only the source or only the relay is coding. In addition to transmission energy, we take into account coding and reception...

Toward distributed relay selection for opportunistic amplify-and-forward transmission

KAUST Repository

Tourki, Kamel

2011-05-01

Opportunistic relaying in cooperative communication depends on careful relay selection. However the traditional centralized method used for opportunistic Amplify-and-Forward (OAF) protocols requires precise measurements of channel state information (CSI) at the destination (CSI-OAF). In this paper, we propose a distributed relay selection framework for opportunistic AF (D-OAF) cooperative communications and offer an accurate performance analysis based on exact statistics of the local signalto- noise ratios of the best relay. Furthermore, we validate our analysis by showing that performance simulation results coincide with our analytical results over different network architectures, and we compare our new results with their CSI-based counterparts. © 2011 IEEE.

Purification and properties of an O-acetyl-transferase from Escherichia coli that can O-acetylate polysialic acid sequences

International Nuclear Information System (INIS)

Higa, H.; Varki, A.

1986-01-01

Certain strains of bacteria synthesize an outer polysialic acid (K1) capsule. Some strains of K1 + E.coli are also capable of adding O-acetyl-esters to the exocyclic hydroxyl groups of the sialic acid residues. Both the capsule and the O-acetyl modification have been correlated with differences in antigenicity and pathogenicity. The authors have developed an assay for an O-acetyl-transferase in E.coli that transfers O-[ 3 H]acetyl groups from [ 3 H]acetyl-Coenzyme A to colominic acid (fragments of the polysialic acid capsule). Using this assay, the enzyme was solubilized, and purified ∼ 600-fold using a single affinity chromatography step with Procion Red-A Agarose. The enzyme also binds to Coenzyme A Sepharose, and can be eluted with high salt or Coenzyme A. The partially purified enzyme has a pH optimum of 7.0 - 7.5, is unaffected by divalent cations, is inhibited by high salt concentrations, is inhibited by Coenzyme A (50% inhibition at 100 μM), and shows an apparent Km for colominic acid of 3.7 mM (sialic acid concentration). This enzyme could be involved in the O-acetyl +/- form variation seen in some strains of K1 + E.coli

Differential patterns of histone acetylation in inflammatory bowel diseases

Directory of Open Access Journals (Sweden)

Adcock Ian M

2011-01-01

Full Text Available Abstract Post-translational modifications of histones, particularly acetylation, are associated with the regulation of inflammatory gene expression. We used two animal models of inflammation of the bowel and biopsy samples from patients with Crohn's disease (CD to study the expression of acetylated histones (H 3 and 4 in inflamed mucosa. Acetylation of histone H4 was significantly elevated in the inflamed mucosa in the trinitrobenzene sulfonic acid model of colitis particularly on lysine residues (K 8 and 12 in contrast to non-inflamed tissue. In addition, acetylated H4 was localised to inflamed tissue and to Peyer's patches (PP in dextran sulfate sodium (DSS-treated rat models. Within the PP, H3 acetylation was detected in the mantle zone whereas H4 acetylation was seen in both the periphery and the germinal centre. Finally, acetylation of H4 was significantly upregulated in inflamed biopsies and PP from patients with CD. Enhanced acetylation of H4K5 and K16 was seen in the PP. These results demonstrate that histone acetylation is associated with inflammation and may provide a novel therapeutic target for mucosal inflammation.

Functional Characterization of ATM Kinase Using Acetylation-Specific Antibodies.

Science.gov (United States)

Sun, Yingli; Du, Fengxia

2017-01-01

The activation of ATM is critical in the DNA double strand breaks repair pathway. Acetylation of ATM by Tip60 histone acetyltransferase (HAT) plays a key role in the activation of ATM kinase activity in response to DNA damage. ATM forms a stable complex with Tip60 through the FATC domain of ATM. Tip60 acetylates lysine3016 of ATM, and this acetylation induces the activation of ATM. Several techniques are included in the study of ATM acetylation by Tip60, such as in vitro kinase assay, systematic mutagenesis, western blots. Here, we describe how to study the acetylation of ATM using acetylation-specific antibodies.

Use of Behavior and Influence Functions for Relay Selection in Cooperative Communications

DEFF Research Database (Denmark)

Craciunescu, Razvan; Mihovska, Albena Dimitrova; Prasad, Ramjee

2015-01-01

This paper uses a novel set of functions to model the relay selection process in a scenario of cooperative wireless communications. We define a utility function that reflects the behavior and influence that a selected relay may have on the quality of the link to be established for the forwarding...... of data. The utility function takes into account also the strategies of other players. To this end, we define a relay selection game and a supporting Nash Equilibrium (NE) algorithm for the choice of a relay during communication. The successful selection of a relay is evaluated by simulations in terms...

CERN Relay Race

CERN Multimedia

2004-01-01

The CERN Relay Race will take place around the Meyrin site on Wednesday 19 May between 12.15 and 12.35. If possible, please avoid driving on the site during this 20 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding

CERN Relay Race

CERN Multimedia

2001-01-01

The CERN Relay Race will take place around the Meyrin site on Wednesday 23 May between 12:20 and 12:35. If possible, please avoid driving on the site during this 15 minute period. If you do meet runners in your car, please stop until they all have passed. Thank you for your understanding.

Two-way CSI-assisted AF relaying with HPA nonlinearity

KAUST Repository

Qi, Jian; Aissa, Sonia; Alouiniz, Mohamed-Slim

2015-01-01

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal

CERN Relay Race

CERN Multimedia

Running Club

2010-01-01

This year’s CERN Relay Race will take place around the Meyrin site on Thursday 20th May at 12h00. This annual event is for teams of 6 runners covering distances of 1000m, 800m, 800m, 500m, 500m and 300m respectively. Teams may be entered in the Seniors, Veterans, Ladies, Mixed or Open categories. The registration fee is 10 CHF per runner, and each runner receives a souvenir prize. As usual, there will be a programme of entertainments from 12h in the arrival area, in front of the Restaurant no. 1. Drinks, food, CERN club information and music will be available for the pleasure of both runners and spectators. The race starts at 12h15, with results and prize giving at 13:15.   For details of the race, and of how to sign up a team, please visit: https://espace.cern.ch/Running-Club/CERN-Relay The event is organised by the CERN Running Club with the support of the CERN Staff Association.  

Energy-efficient cooperative protocols for full-duplex relay channels

KAUST Repository

Khafagy, Mohammad Galal

2013-12-01

In this work, energy-efficient cooperative protocols are studied for full-duplex relaying (FDR) with loopback interference. In these protocols, relay assistance is only sought under certain conditions on the different link outages to ensure effective cooperation. Recently, an energy-efficient selective decode-And-forward protocol was proposed for FDR, and was shown to outperform existing schemes in terms of outage. Here, we propose an incremental selective decode-And-forward protocol that offers additional power savings, while keeping the same outage performance. We compare the performance of the two protocols in terms of the end-to-end signal-to-noise ratio cumulative distribution function via closed-form expressions. Finally, we corroborate our theoretical results with simulation, and show the relative relay power savings in comparison to non-selective cooperation in which the relay cooperates regardless of channel conditions. © 2013 IEEE.

New results on performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel

2013-12-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may be unusable, and takes into account the effect of the possible erroneously detected and transmitted data at the selected relay. We first derive the signal-to-noise (SNR) statistics for each hop, which are used to determine accurate closed form expressions for end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation and end-to-end outage probability for a transmission rate R over Rayleigh fading channels. Furthermore, we evaluate the asymptotical performance and deduce the diversity order. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over linear network architecture. © 2013 Elsevier B.V.

Energy-efficient cooperative protocols for full-duplex relay channels

KAUST Repository

Khafagy, Mohammad Galal; Ismail, Amr; Alouini, Mohamed-Slim; Aï ssa, Sonia

2013-01-01

In this work, energy-efficient cooperative protocols are studied for full-duplex relaying (FDR) with loopback interference. In these protocols, relay assistance is only sought under certain conditions on the different link outages to ensure effective cooperation. Recently, an energy-efficient selective decode-And-forward protocol was proposed for FDR, and was shown to outperform existing schemes in terms of outage. Here, we propose an incremental selective decode-And-forward protocol that offers additional power savings, while keeping the same outage performance. We compare the performance of the two protocols in terms of the end-to-end signal-to-noise ratio cumulative distribution function via closed-form expressions. Finally, we corroborate our theoretical results with simulation, and show the relative relay power savings in comparison to non-selective cooperation in which the relay cooperates regardless of channel conditions. © 2013 IEEE.

Information-guided transmission in decode-and-forward relaying systems: Spatial exploitation and throughput enhancement

KAUST Repository

Yang, Yuli

2011-07-01

In addressing the issue of achieving high throughput in half-duplex relay channels, we exploit a concept of information-guided transmission for the network consisting of a source node, a destination node, and multiple half-duplex relay nodes. For further benefiting from multiple relay nodes, the relay-selection patterns are defined as the arbitrary combinations of given relay nodes. By exploiting the difference among the spatial channels states, in each relay-help transmission additional information to be forwarded is mapped onto the index of the active relay-selection pattern besides the basic information mapped onto the traditional constellation, which is forwarded by the relay node(s) in the active relay-selection pattern, so as to enhance the relay throughtput. With iterative decoding, the destination node can achieve a robust detection by decoupling the signals forwarded in different ways. We investigate the proposed scheme considering "decode-and-forward" protocol and establish its achievable transmission rate. The analytical results on capacity behaviors prove the efficiency of the proposed scheme by showing that it achieves better capacity performance than the conventional scheme. © 2011 IEEE.

Spatially Controlled Relay Beamforming

Science.gov (United States)

Kalogerias, Dionysios

This thesis is about fusion of optimal stochastic motion control and physical layer communications. Distributed, networked communication systems, such as relay beamforming networks (e.g., Amplify & Forward (AF)), are typically designed without explicitly considering how the positions of the respective nodes might affect the quality of the communication. Optimum placement of network nodes, which could potentially improve the quality of the communication, is not typically considered. However, in most practical settings in physical layer communications, such as relay beamforming, the Channel State Information (CSI) observed by each node, per channel use, although it might be (modeled as) random, it is both spatially and temporally correlated. It is, therefore, reasonable to ask if and how the performance of the system could be improved by (predictively) controlling the positions of the network nodes (e.g., the relays), based on causal side (CSI) information, and exploitting the spatiotemporal dependencies of the wireless medium. In this work, we address this problem in the context of AF relay beamforming networks. This novel, cyber-physical system approach to relay beamforming is termed as "Spatially Controlled Relay Beamforming". First, we discuss wireless channel modeling, however, in a rigorous, Bayesian framework. Experimentally accurate and, at the same time, technically precise channel modeling is absolutely essential for designing and analyzing spatially controlled communication systems. In this work, we are interested in two distinct spatiotemporal statistical models, for describing the behavior of the log-scale magnitude of the wireless channel: 1. Stationary Gaussian Fields: In this case, the channel is assumed to evolve as a stationary, Gaussian stochastic field in continuous space and discrete time (say, for instance, time slots). Under such assumptions, spatial and temporal statistical interactions are determined by a set of time and space invariant

Using the 5 P Relay in Task Groups

Science.gov (United States)

Stanley, Paula Helen

2006-01-01

This article describes the 5 P Relay, a group exercise that can increase the effectiveness of task groups. The 5 P Relay is based on the principles and concepts of the Invitational Model, which emphasizes the importance of assessing the effectiveness or health of five aspects of an organization's environment: people, places, programs, processes,…

Studies investigating the excretion of acetyl urea in the milk of dairy cows receiving oral doses of 14C acetyl urea

International Nuclear Information System (INIS)

Bergner, H.; Kijora, C.; Goersch, R.

1976-01-01

2 experimental cows were fed acetyl urea several weeks before the trial was started. The first cow received a daily amount of 200 g and the second cow 855 g. On the first day of experiment both cows were given 5 mCi of 14 C acetyl urea intraruminally. Up to 6 hrs after the beginning of the experiment acetyl urea in blood plasma was shown to contain a higher proportion of 14 C activity than urea. 0.21 g urea and 0.18 g acetyl urea were contained in 1 kg of milk from cow No 1 while 1 kg of milk from cow No 2 contained 0.18 g urea and 0.12 g acetyl urea. The feeding of acetyl urea to dairy cows is not recommended on the basis of the fact that any further contamination of human nutrition with foreign substances should be possibly avoided. (author)

Discovery and characterization of Ku acetylation in Mycobacterium smegmatis.

Science.gov (United States)

Zhou, Ying; Chen, Tao; Zhou, Lin; Fleming, Joy; Deng, Jiaoyu; Wang, Xude; Wang, Liwei; Wang, Yingying; Zhang, Xiaoli; Wei, Wenjing; Bi, Lijun

2015-03-01

Lysine acetylation is an important post-translational modification and is known to regulate many eukaryotic cellular processes. Little, however, is known about acetylated proteins in prokaryotes. Here, using immunoblotting, mass spectrometry and mutagenesis studies, we investigate the acetylation dynamics of the DNA repair protein Ku and its relationship with the deacetylase protein Sir2 and the non-homologous end joining (NHEJ) pathway in Mycobacterium smegmatis. We report that acetylation of Ku increases with growth, while NHEJ activity decreases, providing support for the hypothesis that acetylation of Ku may be involved in the DNA damage response in bacteria. Ku has multiple lysine sites. Our results indicate that K29 is an important acetylation site and that deficiency of Sir2 or mutation of K29 affects the quantity of Ku and its acetylation dynamics. Our findings expand knowledge of acetylation targets in prokaryotes and indicate a new direction for further research on bacterial DNA repair mechanisms. © FEMS 2014. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Comparative analysis of pharmacological treatments with N-acetyl-DL-leucine (Tanganil) and its two isomers (N-acetyl-L-leucine and N-acetyl-D-leucine) on vestibular compensation: Behavioral investigation in the cat.

Science.gov (United States)

Tighilet, Brahim; Leonard, Jacques; Bernard-Demanze, Laurence; Lacour, Michel

2015-12-15

Head roll tilt, postural imbalance and spontaneous nystagmus are the main static vestibular deficits observed after an acute unilateral vestibular loss (UVL). In the UVL cat model, these deficits are fully compensated over 6 weeks as the result of central vestibular compensation. N-Acetyl-dl-leucine is a drug prescribed in clinical practice for the symptomatic treatment of acute UVL patients. The present study investigated the effects of N-acetyl-dl-leucine on the behavioral recovery after unilateral vestibular neurectomy (UVN) in the cat, and compared the effects of each of its two isomers N-acetyl-L-leucine and N-acetyl-D-leucine. Efficacy of these three drug treatments has been evaluated with respect to a placebo group (UVN+saline water) on the global sensorimotor activity (observation grids), the posture control (support surface measurement), the locomotor balance (maximum performance at the rotating beam test), and the spontaneous vestibular nystagmus (recorded in the light). Whatever the parameters tested, the behavioral recovery was strongly and significantly accelerated under pharmacological treatments with N-acetyl-dl-leucine and N-acetyl-L-leucine. In contrast, the N-acetyl-D-leucine isomer had no effect at all on the behavioral recovery, and animals of this group showed the same recovery profile as those receiving a placebo. It is concluded that the N-acetyl-L-leucine isomer is the active part of the racemate component since it induces a significant acceleration of the vestibular compensation process similar (and even better) to that observed under treatment with the racemate component only. Copyright © 2015 Elsevier B.V. All rights reserved.

77 FR 1039 - Internet-Based Telecommunications Relay Service Numbering

Science.gov (United States)

2012-01-09

... FEDERAL COMMUNICATIONS COMMISSION 47 CFR Part 64 [WC Docket No. 10-191; Report No. 2939] Internet... toll-free numbers by users of Internet- based Telecommunications Relay Services (iTRS). DATES... any rules of particular applicability. Subject: Internet-Based Telecommunications Relay Service...

Histone Acetylation in Fungal Pathogens of Plants

Directory of Open Access Journals (Sweden)

Junhyun Jeon

2014-03-01

Full Text Available Acetylation of histone lysine residues occurs in different organisms ranging from yeast to plants and mammals for the regulation of diverse cellular processes. With the identification of enzymes that create or reverse this modification, our understanding on histone acetylation has expanded at an amazing pace during the last two decades. In fungal pathogens of plants, however, the importance of such modification has only just begun to be appreciated in the recent years and there is a dearth of information on how histone acetylation is implicated in fungal pathogenesis. This review covers the current status of research related to histone acetylation in plant pathogenic fungi and considers relevant findings in the interaction between fungal pathogens and host plants. We first describe the families of histone acetyltransferases and deacetylases. Then we provide the cases where histone acetylation was investigated in the context of fungal pathogenesis. Finally, future directions and perspectives in epigenetics of fungal pathogenesis are discussed.

CERN Relay Race

CERN Multimedia

2003-01-01

The CERN Relay Race will take place around the Meyrin site on Wednesday May 21st between 12h15 and 12h35. If possible, please avoid driving on the site during this 20 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding

CERN Relay Race

CERN Document Server

2002-01-01

The CERN Relay Race will take place around the Meyrin site on Wednesday 22 May between 12h20 and 12h35. If possible, please avoid driving on the site during this 15 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding.

Expression of mung bean pectin acetyl esterase in potato tubers: effect on acetylation of cell wall polymers and tuber mechanical properties.

Science.gov (United States)

Orfila, Caroline; Dal Degan, Florence; Jørgensen, Bodil; Scheller, Henrik Vibe; Ray, Peter M; Ulvskov, Peter

2012-07-01

A mung bean (Vigna radiata) pectin acetyl esterase (CAA67728) was heterologously expressed in tubers of potato (Solanum tuberosum) under the control of the granule-bound starch synthase promoter or the patatin promoter in order to probe the significance of O-acetylation on cell wall and tissue properties. The recombinant tubers showed no apparent macroscopic phenotype. The enzyme was recovered from transgenic tubers using a high ionic strength buffer and the extract was active against a range of pectic substrates. Partial in vivo de-acetylation of cell wall polysaccharides occurred in the transformants, as shown by a 39% decrease in the degree of acetylation (DA) of tuber cell wall material (CWM). Treatment of CWM using a combination of endo-polygalacturonase and pectin methyl esterase extracted more pectin polymers from the transformed tissue compared to wild type. The largest effect of the pectin acetyl esterase (68% decrease in DA) was seen in the residue from this extraction, suggesting that the enzyme is preferentially active on acetylated pectin that is tightly bound to the cell wall. The effects of acetylation on tuber mechanical properties were investigated by tests of failure under compression and by determination of viscoelastic relaxation spectra. These tests suggested that de-acetylation resulted in a stiffer tuber tissue and a stronger cell wall matrix, as a result of changes to a rapidly relaxing viscoelastic component. These results are discussed in relation to the role of pectin acetylation in primary cell walls and its implications for industrial uses of potato fibres.

Secrecy Capacity of a Class of Orthogonal Relay Eavesdropper Channels

Directory of Open Access Journals (Sweden)

Aggarwal Vaneet

2009-01-01

Full Text Available The secrecy capacity of relay channels with orthogonal components is studied in the presence of an additional passive eavesdropper node. The relay and destination receive signals from the source on two orthogonal channels such that the destination also receives transmissions from the relay on its channel. The eavesdropper can overhear either one or both of the orthogonal channels. Inner and outer bounds on the secrecy capacity are developed for both the discrete memoryless and the Gaussian channel models. For the discrete memoryless case, the secrecy capacity is shown to be achieved by a partial decode-and-forward (PDF scheme when the eavesdropper can overhear only one of the two orthogonal channels. Two new outer bounds are presented for the Gaussian model using recent capacity results for a Gaussian multiantenna point-to-point channel with a multiantenna eavesdropper. The outer bounds are shown to be tight for two subclasses of channels. The first subclass is one in which the source and relay are clustered, and the eavesdropper receives signals only on the channel from the source and the relay to the destination, for which the PDF strategy is optimal. The second is a subclass in which the source does not transmit to the relay, for which a noise-forwarding strategy is optimal.

Secure Communication for Two-Way Relay Networks with Imperfect CSI

Directory of Open Access Journals (Sweden)

Cong Sun

2017-09-01

Full Text Available This paper considers a two-way relay network, where two legitimate users exchange messages through several cooperative relays in the presence of an eavesdropper, and the Channel State Information (CSI of the eavesdropper is imperfectly known. The Amplify-and-Forward (AF relay protocol is used. We design the relay beamforming weights to minimize the total relay transmit power, while requiring the Signal-to-Noise-Ratio (SNRs of the legitimate users to be higher than the given thresholds and the achievable rate of the eavesdropper to be upper-bounded. Due to the imperfect CSI, a robust optimization problem is summarized. A novel iterative algorithm is proposed, where the line search technique is applied, and the feasibility is preserved during iterations. In each iteration, two Quadratically-Constrained Quadratic Programming (QCQP subproblems and a one-dimensional subproblem are optimally solved. The optimality property of the robust optimization problem is analyzed. Simulation results show that the proposed algorithm performs very close to the non-robust model with perfect CSI, in terms of the obtained relay transmit power; it~achieves higher secrecy rate compared to the existing work. Numerically, the proposed algorithm converges very quickly, and more than 85% of the problems are solved optimally.

Design of Asymmetrical Relay Resonators for Maximum Efficiency of Wireless Power Transfer

Directory of Open Access Journals (Sweden)

Bo-Hee Choi

2016-01-01

Full Text Available This paper presents a new design method of asymmetrical relay resonators for maximum wireless power transfer. A new design method for relay resonators is demanded because maximum power transfer efficiency (PTE is not obtained at the resonant frequency of unit resonator. The maximum PTE for relay resonators is obtained at the different resonances of unit resonator. The optimum design of asymmetrical relay is conducted by both the optimum placement and the optimum capacitance of resonators. The optimum placement is found by scanning the positions of the relays and optimum capacitance can be found by using genetic algorithm (GA. The PTEs are enhanced when capacitance is optimally designed by GA according to the position of relays, respectively, and then maximum efficiency is obtained at the optimum placement of relays. The capacitance of the second resonator to nth resonator and the load resistance should be determined for maximum efficiency while the capacitance of the first resonator and the source resistance are obtained for the impedance matching. The simulated and measured results are in good agreement.

Relay Placement for FSO Multihop DF Systems With Link Obstacles and Infeasible Regions

KAUST Repository

Zhu, Bingcheng

2015-05-19

Optimal relay placement is studied for free-space optical multihop communication with link obstacles and infeasible regions. An optimal relay placement scheme is proposed to achieve the lowest outage probability, enable the links to bypass obstacles of various geometric shapes, and place the relay nodes in specified available regions. When the number of relay nodes is large, the searching space can grow exponentially, and thus, a grouping optimization technique is proposed to reduce the searching time. We numerically demonstrate that the grouping optimization can provide suboptimal solutions close to the optimal solutions, but the average searching time linearly grows with the number of relay nodes. Two useful theorems are presented to reveal insights into the optimal relay locations. Simulation results show that our proposed optimization framework can effectively provide desirable solution to the problem of optimal relay nodes placement. © 2015 IEEE.

Novel half-coherent receivers for amplify-and-forward relaying

KAUST Repository

Khan, Fahd Ahmed; Chen, Yunfei; Alouini, Mohamed-Slim

2012-01-01

Consider a system in which the signal is transmitted from the source to the destination via an amplify-and-forward relay. For such a system, we derive in this paper, novel receivers that have complete knowledge of either the source-relay link

Relay-aided multi-cell broadcasting with random network coding

DEFF Research Database (Denmark)

Lu, Lu; Sun, Fan; Xiao, Ming

2010-01-01

We investigate a relay-aided multi-cell broadcasting system using random network codes, where the focus is on devising efficient scheduling algorithms between relay and base stations. Two scheduling algorithms are proposed based on different feedback strategies; namely, a one-step scheduling...

Mutual Information of Buffer-Aided Full-Duplex Relay Channels

KAUST Repository

Shafie, Ahmed El

2017-04-09

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multiple-output (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Mutual Information of Buffer-Aided Full-Duplex Relay Channels

KAUST Repository

Shafie, Ahmed El; Salem, Ahmed Sultan; Krikidis, Ioannis; Al-Dhahir, Naofal; Hamila, Ridha

2017-01-01

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multiple-output (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Performance analysis of selective cooperation with fixed gain relays in Nakagami-m channels

KAUST Repository

Hussain, Syed Imtiaz; Hasna, Mazen Omar; Alouini, Mohamed-Slim

2012-01-01

Selecting the best relay using the maximum signal to noise ratio (SNR) among all the relays ready to cooperate saves system resources and utilizes the available bandwidth more efficiently compared to the regular all-relay cooperation. In this paper, we analyze the performance of the best relay selection scheme with fixed gain relays operating in Nakagami-. m channels. We first derive the probability density function (PDF) of upper bounded end-to-end SNR of the relay link. Using this PDF, we derive some key performance parameters for the system including average bit error probability and average channel capacity. The analytical results are verified through Monte Carlo simulations. © 2012 Elsevier B.V.

Performance analysis of selective cooperation with fixed gain relays in Nakagami-m channels

KAUST Repository

Hussain, Syed Imtiaz

2012-09-01

Selecting the best relay using the maximum signal to noise ratio (SNR) among all the relays ready to cooperate saves system resources and utilizes the available bandwidth more efficiently compared to the regular all-relay cooperation. In this paper, we analyze the performance of the best relay selection scheme with fixed gain relays operating in Nakagami-. m channels. We first derive the probability density function (PDF) of upper bounded end-to-end SNR of the relay link. Using this PDF, we derive some key performance parameters for the system including average bit error probability and average channel capacity. The analytical results are verified through Monte Carlo simulations. © 2012 Elsevier B.V.

VME Switch for CERN's PS Analog Video System

CERN Document Server

Acebes, I; Heinze, W; Lewis, J; Serrano, J

2003-01-01

Analog video signal switching is used in CERN's Proton Synchrotron (PS) complex to route the video signals coming from Beam Diagnostics systems to the Meyrin Control Room (MCR). Traditionally, this has been done with custom electromechanical relay-based cards controlled serially via CAMAC crates. In order to improve the robustness and maintainability of the system, while keeping it analog to preserve the low latency, a VME card based on Analog Devices' AD8116 analog matrix chip has been developed. Video signals go into the front panel and exit the switch through the P2 connector of the VME backplane. The module is a 16 input, 32 output matrix. Larger matrices can be built using more modules and bussing their outputs together, thanks to the high impedance feature of the AD8116. Another VME module takes the selected signals from the P2 connector and performs automatic gain to send them at nominal output level through its front panel. This paper discusses both designs and presents experimental test results.

New resource allocation scheme for cognitive relay networks with opportunistic access

KAUST Repository

Zafar, Ammar

2012-06-01

In this paper, a new resource allocation scheme to minimize Symbol Error rate (SER) for relay assisted cognitive radio networks is studied. A cognitive relay network with amplify-and-forward (AF) fixed gain relays and opportunistic access to the licensed spectrum is considered. The SER objective function and the optimization constraints are derived first. The resource allocation algorithm is then derived using the Langrangian multiplier method. Closed form expressions are derived for the source and relay powers and, symbol time. Analytical results show that the optimal power allocation follows an extended water-filling solution. © 2012 IEEE.

The sequence relay selection strategy based on stochastic dynamic programming

Science.gov (United States)

Zhu, Rui; Chen, Xihao; Huang, Yangchao

2017-07-01

Relay-assisted (RA) network with relay node selection is a kind of effective method to improve the channel capacity and convergence performance. However, most of the existing researches about the relay selection did not consider the statically channel state information and the selection cost. This shortage limited the performance and application of RA network in practical scenarios. In order to overcome this drawback, a sequence relay selection strategy (SRSS) was proposed. And the performance upper bound of SRSS was also analyzed in this paper. Furthermore, in order to make SRSS more practical, a novel threshold determination algorithm based on the stochastic dynamic program (SDP) was given to work with SRSS. Numerical results are also presented to exhibit the performance of SRSS with SDP.

Channel allocation and rate adaptation for relayed transmission over correlated fading channels

KAUST Repository

Hwang, Kyusung; Hossain, Md Jahangir; Ko, Youngchai; Alouini, Mohamed-Slim

2009-01-01

at both the source and relay nodes, we develop an optimal channel allocation and rate adaptation policy for a dual-hop relayed transmission. As such the overall transmit power for the relayed system is minimized while a target packet dropping rate (PDR

Commercial grade item (CGI) dedication of MDR relays for nuclear safety related applications

Science.gov (United States)

Das, Ranjit K.; Julka, Anil; Modi, Govind

1994-08-01

MDR relays manufactured by Potter & Brumfield (P&B) have been used in various safety related applications in commercial nuclear power plants. These include emergency safety features (ESF) actuation systems, emergency core cooling systems (ECCS) actuation, and reactor protection systems. The MDR relays manufactured prior to May 1990 showed signs of generic failure due to corrosion and outgassing of coil varnish. P&B has made design changes to correct these problems in relays manufactured after May 1990. However, P&B does not manufacture the relays under any 10CFR50 Appendix B quality assurance (QA) program. They manufacture the relays under their commercial QA program and supply these as commercial grade items. This necessitates CGI Dedication of these relays for use in nuclear-safety-related applications. This paper presents a CGI dedication program that has been used to dedicate the MDR relays manufactured after been used to dedicate the MDR relays manufactured after May 1990. The program is in compliance with current Nuclear Regulatory Commission (NRC) and Electric Power Research Institute (EPRI) guidelines and applicable industry standards; it specifies the critical characteristics of the relays, provides the tests and analysis required to verify the critical characteristics, the acceptance criteria for the test results, performs source verification to quality P&B for its control of the critical characteristics, and provides documentation. The program provides reasonable assurance that the new MDR relays will perform their intended safety functions.

Cognitive Spectrum Efficient Multiple Access Technique using Relay Systems

DEFF Research Database (Denmark)

Frederiksen, Flemming Bjerge; Prasad, Ramjee

2007-01-01

Methods to enhance the use of the frequency spectrum by automatical spectrum sensing plus spectrum sharing in a cognitive radio technology context will be presented and discussed in this paper. Ideas to increase the coverage of cellular systems by relay channels, relay stations and collaborate...

Cooperative relay-based multicasting for energy and delay minimization

KAUST Repository

Atat, Rachad; Yaacoub, Elias E.; Alouini, Mohamed-Slim; Abu-Dayya, Adnan A.

2012-01-01

mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles

Massive MIMO Relay Systems with Multipair Wireless Information and Power Transfer

Directory of Open Access Journals (Sweden)

Hongwu Liu

2017-01-01

Full Text Available This paper investigates destination-aided simultaneous wireless information and power transfer (SWIPT for a decode-and-forward relay network, in which massive multiple-input multiple-output antennas are deployed at relay to assist communications among multiple source-destination pairs. During relaying, energy signals are emitted from multiple destinations when multiple sources are sending their information signals to relay. With power splitting and unlimited antennas at relay, asymptotic expression of harvested energy is derived. The analysis reveals that asymptotic harvested energy is independent of fast fading effect of wireless channels; meanwhile transmission powers of each source and destination can be scaled down inversely proportional to the number of relay antennas. To significantly reduce energy leakage interference and multipair interference, zero-forcing processing and maximum-ratio combing/maximum-ratio transmission are employed at relay. Fundamental trade-off between harvested energy and achievable sum rate is quantified. It is shown that asymptotic sum rate is neither convex nor concave with respect to power splitting and destination transmission power. Thus, a one-dimensional embedded bisection algorithm is proposed to jointly determine the optimal power splitting and destination transmission power. It shows that destination-aided SWIPT are beneficial for harvesting energy and increasing sum rate. The significant sum rate improvements of the proposed schemes are verified by numerical results.

CERN Relay Race: information for drivers

CERN Multimedia

2012-01-01

The CERN relay race will take place around the Meyrin site on Thursday, 24 May starting at 12.15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. In addition, there will be a Nordic Walking event which will finish around 12.50. This should not block the roads, but please drive carefully during this time. Thank you for your cooperation. Details on how to register your team for the relay race can be found here.

Improved Relay Node Placement Algorithm for Wireless Sensor Networks Application in Wind Farm

DEFF Research Database (Denmark)

Chen, Qinyin; Hu, Y.; Chen, Zhe

2013-01-01

-tolerance. Each wind turbine has a potentially large number of data points needing to be monitored and collected, as farms continue to increase in scale; distances between turbines can reach several hundred meters. Optimal placement of relays in a large farm requires an efficient algorithmic solution. A relay...... node placement algorithm is proposed in this paper to approximate the optimal position for relays connecting each turbine. However, constraints are then required to prevent relay nodes being overloaded in 3-dimensions. The algorithm is extended to 3-dimensional Euclidean space for this optimal relay...

Performance analysis of two-way amplify and forward relaying with adaptive modulation

KAUST Repository

Hwang, Kyusung

2009-09-01

In this paper, we study two-way amplify-and-forward relaying in conjunction with adaptive modulation over a multiple relay network. In order to keep the diversity order equal to the number of relays and maintain a low complexity, we consider the best relay selection scheme in this work. Based on the proposed selection criterion for the best relay, we analyze the average spectral efficiency by its approximated upper bound. In addition, we extend the proposed scheme to the case where a direct path between source and destination exists. Our numerical examples show that the proposed system offers a considerable gain in the spectral efficiency while satisfying the error rates requirements. ©2009 IEEE.

78 FR 21929 - Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing

Science.gov (United States)

2013-04-12

... Relay Loadability Reliability Standard; Notice of Compliance Filing Take notice that on February 19... Relay Loadability Reliability Standard, Order No. 733, 130 FERC ] 61,221 (2010) (Order No. 733); order..., 136 FERC ] 61,185 (2011). \\2\\ Transmission Relay Loadability Reliability Standard, 138 FERC ] 61,197...

78 FR 55249 - Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing

Science.gov (United States)

2013-09-10

...; RM11-16-000] Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing Take.... \\1\\ Transmission Relay Loadability Reliability Standard, Order No. 733, 130 FERC ] 61, 221 (2010..., Order No. 733-B, 136 FERC ] 61,185 (2011). \\2\\ Transmission Relay Loadability Reliability Standard, 138...

The Acetyl Group Buffering Action of Carnitine Acetyltransferase Offsets Macronutrient-Induced Lysine Acetylation of Mitochondrial Proteins

Directory of Open Access Journals (Sweden)

Michael N. Davies

2016-01-01

Full Text Available Lysine acetylation (AcK, a posttranslational modification wherein a two-carbon acetyl group binds covalently to a lysine residue, occurs prominently on mitochondrial proteins and has been linked to metabolic dysfunction. An emergent theory suggests mitochondrial AcK occurs via mass action rather than targeted catalysis. To test this hypothesis, we performed mass spectrometry-based acetylproteomic analyses of quadriceps muscles from mice with skeletal muscle-specific deficiency of carnitine acetyltransferase (CrAT, an enzyme that buffers the mitochondrial acetyl-CoA pool by converting short-chain acyl-CoAs to their membrane permeant acylcarnitine counterparts. CrAT deficiency increased tissue acetyl-CoA levels and susceptibility to diet-induced AcK of broad-ranging mitochondrial proteins, coincident with diminished whole body glucose control. Sub-compartment acetylproteome analyses of muscles from obese mice and humans showed remarkable overrepresentation of mitochondrial matrix proteins. These findings reveal roles for CrAT and L-carnitine in modulating the muscle acetylproteome and provide strong experimental evidence favoring the nonenzymatic carbon pressure model of mitochondrial AcK.

Outage analysis for underlay relay-assisted cognitive networks

KAUST Repository

Tourki, Kamel; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

2012-01-01

Cooperative relay technology was recently introduced into cognitive radio networks in order to enhance network capacity, scalability, and reliability of end-to-end communication. In this paper, we investigate an underlay cognitive network where the quality of service of the secondary link is maintained by triggering an opportunistic regenerative relaying once it falls under an unacceptable level. We first provide the exact cumulative density function (CDF) of received signal-to-noise (SNR) over each hop with co-located relays. Then, the CDFs are used to determine very accurate closed-form expression for the outage probability for a transmission rate R. We validate our analysis by showing that simulation results coincide with our analytical results in Rayleigh fading channels. © 2012 IEEE.

Outage analysis for underlay relay-assisted cognitive networks

KAUST Repository

Tourki, Kamel

2012-12-01

Cooperative relay technology was recently introduced into cognitive radio networks in order to enhance network capacity, scalability, and reliability of end-to-end communication. In this paper, we investigate an underlay cognitive network where the quality of service of the secondary link is maintained by triggering an opportunistic regenerative relaying once it falls under an unacceptable level. We first provide the exact cumulative density function (CDF) of received signal-to-noise (SNR) over each hop with co-located relays. Then, the CDFs are used to determine very accurate closed-form expression for the outage probability for a transmission rate R. We validate our analysis by showing that simulation results coincide with our analytical results in Rayleigh fading channels. © 2012 IEEE.

PERFORMANCE ANALYSIS OF COOPERATION SCHEMES IN EAVESDROPPER ASSISTED RELAY CHANNEL

Directory of Open Access Journals (Sweden)

Vaibhav Kumar Gupta

2014-06-01

Full Text Available The prominence of the wireless communication has been urging the monotonically increasing demand of security and privacy. In wireless systems, the notion of perfect secrecy of information with respect to illegitimate nodes can be ensured via physical layer security (PLS techniques. Unfortunately, they can be made less effective if source- eavesdropper wiretap channel is better than the main source-receiver channel. The various node cooperation schemes can be employed to combat this limitation where a relay node assists the communication to improve the performance significantly. In this paper, a four node wireless communication system consisting of a source, a destination, a relay and an eavesdropper as wire-tapper has been considered. The performance of the traditional cooperation schemes in terms of secrecy rate has been investigated with a different scenario where relay node helps the eavesdropper to deteriorate the secrecy rate. In addition, since legitimate receiver can overhear the transmission of relay, it favours the achievable secrecy rate. We formulate an analytical expression of conditional secrecy outage probability for the investigated system. From the obtained simulation results, it has been observed that secrecy rate is monotonically increases with path loss index. Furthermore, the proper selection of the system parameters leads to enhance the secrecy performance of the system even if relay pertains to degrade the performance. Amplify-and-forward, cooperation, decode-and-Forward, secrecy rate, relay.

Adhesives for Achieving Durable Bonds with Acetylated Wood

Science.gov (United States)

Charles Frihart; Rishawn Brandon; James Beecher; Rebecca Ibach

2017-01-01

Acetylation of wood imparts moisture durability, decay resistance, and dimensional stability to wood; however, making durable adhesive bonds with acetylated wood can be more difficult than with unmodified wood. The usual explanation is that the acetylated surface has fewer hydroxyl groups, resulting in a harder-to-wet surface and in fewer hydrogen bonds between wood...

Relay selection in cooperative communication systems over continuous time-varying fading channel

Directory of Open Access Journals (Sweden)

Ke Geng

2017-02-01

Full Text Available In this paper, we study relay selection under outdated channel state information (CSI in a decode-and-forward (DF cooperative system. Unlike previous researches on cooperative communication under outdated CSI, we consider that the channel varies continuously over time, i.e., the channel not only changes between relay selection and data transmission but also changes during data transmission. Thus the level of accuracy of the CSI used in relay selection degrades with data transmission. We first evaluate the packet error rate (PER of the cooperative system under continuous time-varying fading channel, and find that the PER performance deteriorates more seriously under continuous time-varying fading channel than when the channel is assumed to be constant during data transmission. Then, we propose a repeated relay selection (RRS strategy to improve the PER performance, in which the forwarded data is divided into multiple segments and relay is reselected before the transmission of each segment based on the updated CSI. Finally, we propose a combined relay selection (CRS strategy which takes advantage of three different relay selection strategies to further mitigate the impact of outdated CSI.

Minimax robust relay selection based on uncertain long-term CSI

KAUST Repository

Nisar, Muhammad Danish; Alouini, Mohamed-Slim

2014-01-01

Cooperative communications via multiple relay nodes is known to provide the benefits of increase diversity and coverage. Simultaneous transmission via multiple relays, however, requires strong coordination between nodes either in terms of slot

On full duplex Gaussian relay channels with self-interference

KAUST Repository

Behboodi, Arash

2016-08-15

Self interference (SI) in full duplex (FD) systems is the interference caused by the transmission stream on the reception stream. Being one of the main restrictive factors for performance of practical full duplex systems, however, not too much is known about its effect on the fundamental limits of relaying systems. In this work, we consider the full duplex three-node relay channel with SI where SI is modeled as an additive Gaussian noise whose variance is dependent on instantaneous input power. The classical achievable rates and upper bounds for the single three-node relay channel no longer apply due to the structure of SI. Achievable rates for Decode-and-Forward (DF) and Compress-and-Forward (CF) and upper bounds on the capacity are derived assuming Gaussian inputs and SI. The deterministic model is also introduced and its capacity is characterized. The optimal joint source-relay distributions is discussed. Numerical results are provided comparing the achievable rates and upper bound. © 2016 IEEE.

Superimposed Training-Based Channel Estimation for MIMO Relay Networks

Directory of Open Access Journals (Sweden)

Xiaoyan Xu

2012-01-01

Full Text Available We introduce the superimposed training strategy into the multiple-input multiple-output (MIMO amplify-and-forward (AF one-way relay network (OWRN to perform the individual channel estimation at the destination. Through the superposition of a group of additional training vectors at the relay subject to power allocation, the separated estimates of the source-relay and relay-destination channels can be obtained directly at the destination, and the accordance with the two-hop AF strategy can be guaranteed at the same time. The closed-form Bayesian Cramér-Rao lower bound (CRLB is derived for the estimation of two sets of flat-fading MIMO channel under random channel parameters and further exploited to design the optimal training vectors. A specific suboptimal channel estimation algorithm is applied in the MIMO AF OWRN using the optimal training sequences, and the normalized mean square error performance for the estimation is provided to verify the Bayesian CRLB results.

Selection combining for noncoherent decode-and-forward relay networks

Directory of Open Access Journals (Sweden)

Nguyen Ha

2011-01-01

Full Text Available Abstract This paper studies a new decode-and-forward relaying scheme for a cooperative wireless network composed of one source, K relays, and one destination and with binary frequency-shift keying modulation. A single threshold is employed to select retransmitting relays as follows: a relay retransmits to the destination if its decision variable is larger than the threshold; otherwise, it remains silent. The destination then performs selection combining for the detection of transmitted information. The average end-to-end bit-error-rate (BER is analytically determined in a closed-form expression. Based on the derived BER, the problem of choosing an optimal threshold or jointly optimal threshold and power allocation to minimize the end-to-end BER is also investigated. Both analytical and simulation results reveal that the obtained optimal threshold scheme or jointly optimal threshold and power-allocation scheme can significantly improve the BER performance compared to a previously proposed scheme.

Novel half-coherent receivers for amplify-and-forward relaying

KAUST Repository

Khan, Fahd Ahmed

2012-06-01

Consider a system in which the signal is transmitted from the source to the destination via an amplify-and-forward relay. For such a system, we derive in this paper, novel receivers that have complete knowledge of either the source-relay link or the relay-destination link. These receivers are termed as, \\'half-coherent receivers\\' as they have channel-state-information (CSI) of only one of two links. These receivers can be very useful in a system in which only the relay can afford high complexity by having a channel estimation module and the destination is unable to support channel estimation or a system in which only the destination can afford higher complexity and includes the channel estimation module. The analytical bit-error-rate (BER) performances of the proposed receivers are derived for Rician fading. Numerical results show considerable performance gains of the new receivers, especially at low signal-to-noise ratio. © 2012 IEEE.

Relay-Assisted Primary and Secondary Transmissions in Cognitive Radio Networks

KAUST Repository

Shafie, Ahmed El

2016-09-27

We assume a set of cognitive relay nodes that assists both primary and secondary transmissions in a time-slotted cognitive radio networks. To regulate the channel access of the various nodes in the network, we propose an overlapped spectrum sensing strategy for channel sensing, where the secondary source node senses the channel from the beginning of the time slot and the cognitive relay nodes sense the channel for double the sensing time used by the secondary source node to detect the activities of both the primary and secondary source nodes. Hence, the secondary source node has an intrinsic priority over the relay nodes. The relay nodes help both the primary user and the secondary user to deliver their unsuccessfully decoded packets at their destinations. In a given time slot, the scheduled relay node for data transmission starts its transmission when both the primary and secondary users are sensed to be inactive (i.e. have no data to transmit). We propose two optimization-based formulations with quality-of-service (QoS) constraints involving average queueing delay and average service rate requirements. We investigate both cases of perfect and imperfect spectrum sensing. To further enhance the users\\' QoS requirements, we propose three packet decoding strategies at the relay nodes and compare their performance. We derive an upper bound on the secondary queue average service rate to determine which decoding strategy can achieve that bound. Our numerical results show the benefits of relaying and its ability to enhance the performance of both the primary and secondary users. Moreover, the performance of the proposed schemes is close to the derived upper bound.

Studies investigating the excretion of acetyl urea in the milk of dairy cows receiving oral doses of /sup 14/C acetyl urea

Energy Technology Data Exchange (ETDEWEB)

Bergner, H; Kijora, C; Goersch, R [Humboldt-Universitaet, Berlin (German Democratic Republic). Sektion Tierproduktion und Veterinaermedizin

1976-01-01

2 experimental cows were fed acetyl urea several weeks before the trial was started. The first cow received a daily amount of 200 g and the second cow 855 g. On the first day of experiment both cows were given 5 mCi of /sup 14/C acetyl urea intraruminally. Up to 6 hrs after the beginning of the experiment acetyl urea in blood plasma was shown to contain a higher proportion of /sup 14/C activity than urea. 0.21 g urea and 0.18 g acetyl urea were contained in 1 kg of milk from cow No 1 while 1 kg of milk from cow No 2 contained 0.18 g urea and 0.12 g acetyl urea. The feeding of acetyl urea to dairy cows is not recommended on the basis of the fact that any further contamination of human nutrition with foreign substances should be possibly avoided.

Susceptibility of modern relay protection: Will protection from cyber attacks help?

Directory of Open Access Journals (Sweden)

Gurevich Vladimir

2014-01-01

Full Text Available Modern trends in relay protection (RP based on the substitution of electromechanical protection relays (EMPR by digital protective relays (DPR have resulted in the emergence of an absolutely new problem, which was not known before. This problem is the possibility of an intentional remote destructive impact (IRDI on relay protection in order to put it out of action or make it perform functions that have nothing to do with the current operational mode of protected electric equipment. Traditional and well-known methods ensuring information safety cannot fully prevent unauthorized actions of RP. The article describes a new way for the problem solution.

Acetylation Increases EWS-FLI1 DNA Binding and Transcriptional Activity

International Nuclear Information System (INIS)

Schlottmann, Silke; Erkizan, Hayriye V.; Barber-Rotenberg, Julie S.; Knights, Chad; Cheema, Amrita; Üren, Aykut; Avantaggiati, Maria L.; Toretsky, Jeffrey A.

2012-01-01

Ewing Sarcoma (ES) is associated with a balanced chromosomal translocation that in most cases leads to the expression of the oncogenic fusion protein and transcription factor EWS-FLI1. EWS-FLI1 has been shown to be crucial for ES cell survival and tumor growth. However, its regulation is still enigmatic. To date, no functionally significant post-translational modifications of EWS-FLI1 have been shown. Since ES are sensitive to histone deacetylase inhibitors (HDI), and these inhibitors are advancing in clinical trials, we sought to identify if EWS-FLI1 is directly acetylated. We convincingly show acetylation of the C-terminal FLI1 (FLI1-CTD) domain, which is the DNA binding domain of EWS-FLI1. In vitro acetylation studies showed that acetylated FLI1-CTD has higher DNA binding activity than the non-acetylated protein. Over-expression of PCAF or treatment with HDI increased the transcriptional activity of EWS-FLI1, when co-expressed in Cos7 cells. However, our data that evaluates the acetylation of full-length EWS-FLI1 in ES cells remains unclear, despite creating acetylation specific antibodies to four potential acetylation sites. We conclude that EWS-FLI1 may either gain access to chromatin as a result of histone acetylation or undergo regulation by direct acetylation. These data should be considered when patients are treated with HDAC inhibitors. Further investigation of this phenomenon will reveal if this potential acetylation has an impact on tumor response.

Low Complexity Transmission Scheme with Full Diversity for Two-Path Relay Networks

KAUST Repository

Fareed, Muhammad Mehboob

2014-01-06

In this work, we present a new low complexity scheme for two-path relay network to harvest maximum achievable diversity. We analyze the performance of the newly proposed two-path relay network by calculating the symbol error rate (SER) for arbitrary location of relays. It is shown that with this newly proposed scheme, two-path relay networks can mimic a 2x2 multiple-input mulitple-output (MIMO) system and achieve full diversity order of four. Simulations results are provided to verify and illustrate the analytical results.

Low Complexity Transmission Scheme with Full Diversity for Two-Path Relay Networks

KAUST Repository

Fareed, Muhammad Mehboob; Yang, Hong-Chuan; Alouini, Mohamed-Slim

2014-01-01

In this work, we present a new low complexity scheme for two-path relay network to harvest maximum achievable diversity. We analyze the performance of the newly proposed two-path relay network by calculating the symbol error rate (SER) for arbitrary location of relays. It is shown that with this newly proposed scheme, two-path relay networks can mimic a 2x2 multiple-input mulitple-output (MIMO) system and achieve full diversity order of four. Simulations results are provided to verify and illustrate the analytical results.

protective relay studies for the nigerian national electric 330 kv

African Journals Online (AJOL)

user

1985-09-01

Sep 1, 1985 ... protective relay schemes of the National Electric Power Authority. Some of the basic ... Nigerian special system characteristics, schemes to correct existing protection inadequacies .... relays buried in the transformer. A reach of ...

Adjustable electronic load-alarm relay

International Nuclear Information System (INIS)

Mason, C.H.; Sitton, R.S.

1976-01-01

An improved electronic alarm relay for monitoring the current drawn by an ac motor or other electrical load is described. The circuit is designed to measure the load with high accuracy and to have excellent alarm repeatability. Chattering and arcing of the relay contacts are minimal. The operator can adjust the set point easily and can re-set both the high and the low alarm points by means of one simple adjustment. The relay includes means for generating a signal voltage proportional to the motor current. In a preferred form of the invention a first operational amplifier is provided to generate a first constant reference voltage which is higher than a preselected value of the signal voltage. A second operational amplifier is provided to generate a second constant reference voltage which is lower than the aforementioned preselected value of the signal voltage. A circuit comprising a first resistor serially connected to a second resistor is connected across the outputs of the first and second amplifiers, and the junction of the two resistors is connected to the inverting terminal of the second amplifier. Means are provided to compare the aforementioned signal voltage with both the first and second reference voltages and to actuate an alarm if the signal voltage is higher than the first reference voltage or lower than the second reference voltage

Next-Generation NASA Earth-Orbiting Relay Satellites: Fusing Optical and Microwave Communications

Science.gov (United States)

Israel, David J.; Shaw, Harry

2018-01-01

NASA is currently considering architectures and concepts for the generation of relay satellites that will replace the Tracking and Data Relay Satellite (TDRS) constellation, which has been flying since 1983. TDRS-M, the last of the second TDRS generation, launched in August 2017, extending the life of the TDRS constellation beyond 2030. However, opportunities exist to re-engineer the concepts of geosynchronous Earth relay satellites. The needs of the relay satellite customers have changed dramatically over the last 34 years since the first TDRS launch. There is a demand for greater bandwidth as the availability of the traditional RF spectrum for space communications diminishes and the demand for ground station access grows. The next generation of NASA relay satellites will provide for operations that have factored in these new constraints. In this paper, we describe a heterogeneous constellation of geosynchronous relay satellites employing optical and RF communications. The new constellation will enable new optical communications services formed by user-to-space relay, space relay-to-space relay and space relay-to-ground links. It will build upon the experience from the Lunar Laser Communications Demonstration from 2013 and the Laser Communications Relay Demonstration to be launched in 2019.Simultaneous to establishment of the optical communications space segment, spacecraft in the TDRS constellation will be replaced with RF relay satellites with targeted subsets of the TDRS capabilities. This disaggregation of the TDRS service model will allow for flexibility in replenishing the needs of legacy users as well as addition of new capabilities for future users. It will also permit the U.S. government access to launch capabilities such as rideshare and to hosted payloads that were not previously available.In this paper, we also explore how the next generation of Earth relay satellites provides a significant boost in the opportunities for commercial providers to the

Next-Generation NASA Earth-Orbiting Relay Satellites: Fusing Microwave and Optical Communications

Science.gov (United States)

Israel, David J.

2018-01-01

NASA is currently considering architectures and concepts for the generation of relay satellites that will replace the Tracking and Data Relay Satellite (TDRS) constellation, which has been flying since 1983. TDRS-M, the last of the second TDRS generation, launched in August 2017, extending the life of the TDRS constellation beyond 2030. However, opportunities exist to re-engineer the concepts of geosynchronous Earth relay satellites. The needs of the relay satellite customers have changed dramatically over the last 34 years since the first TDRS launch. There is a demand for greater bandwidth as the availability of the traditional RF spectrum for space communications diminishes and the demand for ground station access grows. The next generation of NASA relay satellites will provide for operations that have factored in these new constraints. In this paper, we describe a heterogeneous constellation of geosynchronous relay satellites employing optical and RF communications. The new constellation will enable new optical communications services formed by user-to-space relay, space relay-to-space relay and space relay-to-ground links. It will build upon the experience from the Lunar Laser Communications Demonstration from 2013 and the Laser Communications Relay Demonstration to be launched in 2019.Simultaneous to establishment of the optical communications space segment, spacecraft in the TDRS constellation will be replaced with RF relay satellites with targeted subsets of the TDRS capabilities. This disaggregation of the TDRS service model will allow for flexibility in replenishing the needs of legacy users as well as addition of new capabilities for future users. It will also permit the U.S. government access to launch capabilities such as rideshare and to hosted payloads that were not previously available. In this paper, we also explore how the next generation of Earth relay satellites provides a significant boost in the opportunities for commercial providers to the

Proposed Suitable Methods to Detect Transient Regime Switching to Improve Power Quality with Wavelet Transform

Directory of Open Access Journals (Sweden)

Javad Safaee Kuchaksaraee

2016-10-01

Full Text Available The increasing consumption of electrical energy and the use of non-linear loads that create transient regime states in distribution networks is increasing day by day. This is the only reason due to which the analysis of power quality for energy sustainability in power networks has become more important. Transients are often created by energy injection through switching or lightning and make changes in voltage and nominal current. Sudden increase or decrease in voltage or current makes characteristics of the transient regime. This paper shed some lights on the capacitor bank switching, which is one of the main causes for oscillatory transient regime states in the distribution network, using wavelet transform. The identification of the switching current of capacitor bank and the internal fault current of the transformer to prevent the unnecessary outage of the differential relay, it propose a new smart method. The accurate performance of this method is shown by simulation in EMTP and MATLAB (matrix laboratory software.

On achievable rates of interference and cognitive channels with a relay

KAUST Repository

Zorgui, Marwen; Rezki, Zouheir; Alouini, Mohamed-Slim

2015-01-01

We consider a two-user interference channel assisted by a relay. Treating interference as noise at the receivers, and adopting an amplify and forward (AF) strategy at the relay, we derive achievable rates of both users, for given powers. Next, we solve the optimal power allocation problem maximizing the weighted sum rate of both users with and without relay power optimization. In particular, we propose a simple iterative line search algorithm solving the joint optimization problem over the three transmit powers and show that optimizing the relay power enhances the performance of the system. Then, considering the first user as a primary user, we determine the maximum instantaneous rate that the secondary user can achieve subject to an outage constraint with respect to the primary user and a peak power constraint. We show that, likewise the first part, jointly optimizing the secondary user and the relay transmit powers enhances the secondary user performance.

On achievable rates of interference and cognitive channels with a relay

KAUST Repository

Zorgui, Marwen

2015-08-30

We consider a two-user interference channel assisted by a relay. Treating interference as noise at the receivers, and adopting an amplify and forward (AF) strategy at the relay, we derive achievable rates of both users, for given powers. Next, we solve the optimal power allocation problem maximizing the weighted sum rate of both users with and without relay power optimization. In particular, we propose a simple iterative line search algorithm solving the joint optimization problem over the three transmit powers and show that optimizing the relay power enhances the performance of the system. Then, considering the first user as a primary user, we determine the maximum instantaneous rate that the secondary user can achieve subject to an outage constraint with respect to the primary user and a peak power constraint. We show that, likewise the first part, jointly optimizing the secondary user and the relay transmit powers enhances the secondary user performance.

On the malfunction of disk-type induction relay under seismic condition

International Nuclear Information System (INIS)

Fujita, T.; Shibata, H.; Koizumi, T.

1985-01-01

This paper deals with the malfunction of disk-type induction relay. Equations of motion for rotational movement of induction relay was formulated and the dynamic behavior was simulated under various kind of exciting conditions. Experimental verification was also performed using two dimensional shaker table for some actual relays. Sufficient agreement was recognized between experimental and analytical results and consequently the most critical reason to cause the malfunction was pointed out. (orig.)

Optimal Coordination of Distance and Directional Overcurrent Relays Considering Different Network Topologies

Directory of Open Access Journals (Sweden)

Y. Damchi

2015-09-01

Full Text Available Most studies in relay coordination have focused solely on coordination of overcurrent relays while distance relays are used as the main protection of transmission lines. Since, simultaneous coordination of these two types of relays can provide a better protection, in this paper, a new approach is proposed for simultaneous coordination of distance and directional overcurrent relays (D&DOCRs. Also, pursued by most of the previously published studies, the settings of D&DOCRs are usually determined based on a main network topology which may result in mis-coordination of relays when changes occur in the network topology. In the proposed method, in order to have a robust coordination, network topology changes are taken into account in the coordination problem. In the new formulation, coordination constraints for different network topologies are added to those of the main topology. A complex nonlinear optimization problem is derived to find the desirable relay settings. Then, the problem is solved using hybridized genetic algorithm (GA with linear programming (LP method (HGA. The proposed method is evaluated using the IEEE 14-bus test system. According to the results, a feasible and robust solution is obtained for D&DOCRs coordination while all constraints, which are due to different network topologies, are satisfied.

Transmission Power Adaption for Full-Duplex Relay-Aided Device-to-Device Communication

Directory of Open Access Journals (Sweden)

Hui Dun

2017-03-01

Full Text Available Device-to-device (D2D communications bring significant improvements of spectral efficiency by underlaying cellular networks. However, they also lead to a more deteriorative interference environment for cellular users, especially the users in severely deep fading or shadowing. In this paper, we investigate a relay-based communication scheme in cellular systems, where the D2D communications are exploited to aid the cellular downlink transmissions by acting as relay nodes with underlaying cellular networks. We modeled two-antenna infrastructure relays employed for D2D relay. The D2D transmitter is able to transmit and receive signals simultaneously over the same frequency band. Then we proposed an efficient power allocation algorithm for the base station (BS and D2D relay to reduce the loopback interference which is inherent due to the two-antenna infrastructure in full-duplex (FD mode. We derived the optimal power allocation problem in closed form under the independent power constraint. Simulation results show that the algorithm reduces the power consumption of D2D relay to the greatest extent and also guarantees cellular users’ minimum transmit rate. Moreover, it also outperforms the existing half-duplex (HD relay mode in terms of achievable rate of D2D.

Low-Complexity Combining Schemes in Dual-Hop AF Relaying Systems

KAUST Repository

Gaaloul, Fakhreddine; Alouini, Mohamed-Slim; Radaydeh, Redha M.

2011-01-01

This paper investigates the performance of different low-complexity combining schemes in the context of dual-hop amplify-and-forward (AF) relaying networks. It is assumed that the relay uses single transmit (receive) antenna due to space limitation

IE Information Notice No. 85-82: Diesel generator differential protection relay not seismically qualified

International Nuclear Information System (INIS)

Jordan, E.L.

1992-01-01

Licensees of BWR and PWR nuclear generating stations have reported using a high-speed differential protection relay that has been declared by the manufacturer to be not seismically qualified for the service intended. The relay, GE Model 12CFD, which is being used for emergency diesel generator protection against electrical shorts and grounds at the generator output, has not been seismically qualified to operate in the de-energized state for this application. Generally, the relay operates in the de-energized position before EDG operation. However, it then operates in the energized position whenever the EDG provides an electrical output to essential Class IE components. The safety concern of this issue involves an inadvertent activation of the normally de-energized relay from a seismic event. Momentary activation of the relay, in the circuits examined, blocks the automatic start feature of the EDG during certain emergency plant conditions through operation of another relay in the system. The NRC review of the problems concluded that the relays should be seismically qualified in their energized and de-energized states to preclude their spurious activation during a seismic event. Additionally, review of GE's GER 3069 report, ''Relay Protection of Class IE Systems,'' shows that the 12CFD differential relays were successfully tested for 3.5 g in the energized modes and only 0.75 g in the de-energized mode. Review of GE's GER 3069 report also revealed that GE type IJD differential relays do meet seismic requirements in all modes of operation mentioned above and is the GE recommendation for replacement of the differential relay in question

Implementing Strategic Planning Capabilities Within the Mars Relay Operations Service

Science.gov (United States)

Hy, Franklin; Gladden, Roy; Allard, Dan; Wallick, Michael

2011-01-01

Since the Mars Exploration Rovers (MER), Spirit and Opportunity, began their travels across the Martian surface in January of 2004, orbiting spacecraft such as the Mars 2001 Odyssey orbiter have relayed the majority of their collected scientific and operational data to and from Earth. From the beginning of those missions, it was evident that using orbiters to relay data to and from the surface of Mars was a vastly more efficient communications strategy in terms of power consumption and bandwidth compared to direct-to-Earth means. However, the coordination between the various spacecraft, which are largely managed independently and on differing commanding timelines, has always proven to be a challenge. Until recently, the ground operators of all these spacecraft have coordinated the movement of data through this network using a collection of ad hoc human interfaces and various, independent software tools. The Mars Relay Operations Service (MaROS) has been developed to manage the evolving needs of the Mars relay network, and specifically to standardize and integrate the relay planning and coordination data into a centralized infrastructure. This paper explores the journey of developing the MaROS system, from inception to delivery and acceptance by the Mars mission users.

Outage Probability Analysis in Power-Beacon Assisted Energy Harvesting Cognitive Relay Wireless Networks

Directory of Open Access Journals (Sweden)

Ngoc Phuc Le

2017-01-01

Full Text Available We study the performance of the secondary relay system in a power-beacon (PB assisted energy harvesting cognitive relay wireless network. In our system model, a secondary source node and a relay node first harvest energy from distributed PBs. Then, the source node transmits its data to the destination node with the help of the relay node. Also, fading coefficients of the links from the PBs to the source node and relay node are assumed independent but not necessarily identically distributed (i.n.i.d Nakagami-m random variables. We derive exact expressions for the power outage probability and the channel outage probability. Based on that, we analyze the total outage probability of the secondary relay system. Asymptotic analysis is also performed, which provides insights into the system behavior. Moreover, we evaluate impacts of the primary network on the performance of the secondary network with respect to the tolerant interference threshold at the primary receiver as well as the interference introduced by the primary transmitter at the secondary source and relay nodes. Simulation results are provided to validate the analysis.

Achievable Rates of Buffer-Aided Full-Duplex Gaussian Relay Channels

KAUST Repository

El Shafie, Ahmed

2017-10-18

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multipleoutput (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Achievable Rates of Buffer-Aided Full-Duplex Gaussian Relay Channels

KAUST Repository

El Shafie, Ahmed; Salem, Ahmed Sultan; Krikidis, Ioannis; Al-Dhahir, Naofal; Hamila, Ridha

2017-01-01

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multipleoutput (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Rate regions for coordination of Decode-and-Forward relays and direct users

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar

2012-01-01

Recently, the ideas of wireless network coding (NC) has significantly enriched the area of wireless cooperation/relaying. They bring substantial gains in spectral efficiency mainly in scenarios with two–way relaying. Inspired by the ideas of wireless NC, recently we have proposed techniques...... for coordinated direct/relay (CDR) transmissions. Leveraging on the fact that the interference can be subsequently canceled, these techniques embrace the interference among the communication flows to/from direct and relayed users. Hence, by allowing simultaneous transmissions, spectral efficiency is increased....... In our prior work, we have proposed CDR with Decode–and–Forward (DF) relay in two scenarios. In this paper, we extend the two existing regenerative CDR schemes and proposed for the other two scenarios such that all schemes benefit from the aforementioned principle of containing the interference...

Autoimmune regulator is acetylated by transcription coactivator CBP/p300

Energy Technology Data Exchange (ETDEWEB)

Saare, Mario, E-mail: mario.saare@ut.ee [Molecular Pathology, Institute of General and Molecular Pathology, University of Tartu, 19th Ravila Str, Tartu (Estonia); Rebane, Ana [Molecular Pathology, Institute of General and Molecular Pathology, University of Tartu, 19th Ravila Str, Tartu (Estonia); SIAF, Swiss Institute of Allergy and Asthma Research, University of Zuerich, Davos (Switzerland); Rajashekar, Balaji; Vilo, Jaak [BIIT, Bioinformatics, Algorithmics and Data Mining group, Institute of Computer Science, University of Tartu, Tartu (Estonia); Peterson, Paert [Molecular Pathology, Institute of General and Molecular Pathology, University of Tartu, 19th Ravila Str, Tartu (Estonia)

2012-08-15

The Autoimmune Regulator (AIRE) is a regulator of transcription in the thymic medulla, where it controls the expression of a large set of peripheral-tissue specific genes. AIRE interacts with the transcriptional coactivator and acetyltransferase CBP and synergistically cooperates with it in transcriptional activation. Here, we aimed to study a possible role of AIRE acetylation in the modulation of its activity. We found that AIRE is acetylated in tissue culture cells and this acetylation is enhanced by overexpression of CBP and the CBP paralog p300. The acetylated lysines were located within nuclear localization signal and SAND domain. AIRE with mutations that mimicked acetylated K243 and K253 in the SAND domain had reduced transactivation activity and accumulated into fewer and larger nuclear bodies, whereas mutations that mimicked the unacetylated lysines were functionally similar to wild-type AIRE. Analogously to CBP, p300 localized to AIRE-containing nuclear bodies, however, the overexpression of p300 did not enhance the transcriptional activation of AIRE-regulated genes. Further studies showed that overexpression of p300 stabilized the AIRE protein. Interestingly, gene expression profiling revealed that AIRE, with mutations mimicking K243/K253 acetylation in SAND, was able to activate gene expression, although the affected genes were different and the activation level was lower from those regulated by wild-type AIRE. Our results suggest that the AIRE acetylation can influence the selection of AIRE activated genes. -- Highlights: Black-Right-Pointing-Pointer AIRE is acetylated by the acetyltransferases p300 and CBP. Black-Right-Pointing-Pointer Acetylation occurs between CARD and SAND domains and within the SAND domain. Black-Right-Pointing-Pointer Acetylation increases the size of AIRE nuclear dots. Black-Right-Pointing-Pointer Acetylation increases AIRE protein stability. Black-Right-Pointing-Pointer AIRE acetylation mimic regulates a different set of AIRE

Synthesis of relay control systems for nuclear reactors

International Nuclear Information System (INIS)

Postnikov, N.S.

1996-01-01

The problem on stabilizing an oscillatory-unstable reactor by a single-link relay system, the characteristics whereof have a dead zone and hysteresis loop, is considered. The methodology of synthesis of feedback law, providing for stochastic steady-state mode of reactor operation with the minimum frequency of control impact introduction is proposed. This methodology is applicable to general-type relay systems with arbitrary oscillatory-unstable objects. 6 refs., 5 figs

Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

KAUST Repository

Benkhelifa, Fatma; Alouini, Mohamed-Slim

2016-01-01

relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the source-destination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal

Interference alignment for degrees of freedom improvement in 3-relay half-duplex systems

KAUST Repository

Park, Seongho; Ko, Youngchai; Park, Kihong; Alouini, Mohamed-Slim

2011-01-01

In a half-duplex relaying, the capacity pre-log factor is a major drawback in spectral efficiency. This paper proposes a linear precoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help

Uplink Capacity of 802.16j Mobile Multihop Relay Networks with Transparent Relays

DEFF Research Database (Denmark)

Wang, Hua; Andrews, Jeffrey G.; Iversen, Villy Bæk

2009-01-01

-to-end spectral efficiency. Furthermore, the position and the number of relay stations (RSs) have a great impact on the capacity gain. These results are further verified in the evaluation of the system Erlang capacity. The study demonstrates that with proper deployment of RSs and use of MIMO transmission...

Relay Coordination in the Protection of Radially-Connected Power ...

African Journals Online (AJOL)

Protective relays detect intolerable or unwanted conditions within an assigned area, and then trip or open one or more circuit breakers to isolate the problem area before it can damage or otherwise interfere with the eective operation of the rest of the power system. It often happens that a substation feeder relay and ...

Relay chatter and operator response after a large earthquake: An improved PRA methodology with case studies

International Nuclear Information System (INIS)

Budnitz, R.J.; Lambert, H.E.; Hill, E.E.

1987-08-01

The purpose of this project has been to develop and demonstrate improvements in the PRA methodology used for analyzing earthquake-induced accidents at nuclear power reactors. Specifically, the project addresses methodological weaknesses in the PRA systems analysis used for studying post-earthquake relay chatter and for quantifying human response under high stress. An improved PRA methodology for relay-chatter analysis is developed, and its use is demonstrated through analysis of the Zion-1 and LaSalle-2 reactors as case studies. This demonstration analysis is intended to show that the methodology can be applied in actual cases, and the numerical values of core-damage frequency are not realistic. The analysis relies on SSMRP-based methodologies and data bases. For both Zion-1 and LaSalle-2, assuming that loss of offsite power (LOSP) occurs after a large earthquake and that there are no operator recovery actions, the analysis finds very many combinations (Boolean minimal cut sets) involving chatter of three or four relays and/or pressure switch contacts. The analysis finds that the number of min-cut-set combinations is so large that there is a very high likelihood (of the order of unity) that at least one combination will occur after earthquake-caused LOSP. This conclusion depends in detail on the fragility curves and response assumptions used for chatter. Core-damage frequencies are calculated, but they are probably pessimistic because assuming zero credit for operator recovery is pessimistic. The project has also developed an improved PRA methodology for quantifying operator error under high-stress conditions such as after a large earthquake. Single-operator and multiple-operator error rates are developed, and a case study involving an 8-step procedure (establishing feed-and-bleed in a PWR after an earthquake-initiated accident) is used to demonstrate the methodology

On the capacity of multiple cognitive links through common relay under spectrum-sharing constraints

KAUST Repository

Yang, Yuli

2011-06-01

In this paper, we consider an underlay cognitive relaying network consisting of multiple secondary users and introduce a cooperative transmission protocol using a common relay to help with the communications between all secondary source-destination pairs for higher throughput and lower realization complexity. A whole relay-assisted transmission procedure is composed of multiple access phase and broadcast phase, where the relay is equipped with multiple antennas, and the secondary sources and destinations are single-antenna nodes. Considering the spectrum-sharing constraints on the secondary sources and the relay, we analyze the capacity behaviors of the underlay cognitive relaying network under study. The corresponding numerical results provide a convenient tool for the presented network design and substantiate a distinguishing feature of introduced design in that multiple secondary users\\' communications do not rely on multiple relays, hence allowing for a more efficient use of the radio resources. © 2011 IEEE.

Social-Aware Relay Selection for Cooperative Multicast Device-to-Device Communications

Directory of Open Access Journals (Sweden)

Francesco Chiti

2017-12-01

Full Text Available The increasing use of social networks such as Facebook, Twitter, and Instagram to share photos, video streaming, and music among friends has generated a huge increase in the amount of data traffic over wireless networks. This social behavior has triggered new communication paradigms such as device-to-device (D2D and relaying communication schemes, which are both considered as strong drivers for the next fifth-generation (5G cellular systems. Recently, the social-aware layer and its relationship to and influence on the physical communications layer have gained great attention as emerging focus points. We focus here on the case of relaying communications to pursue the multicast data dissemination to a group of users forming a social community through a relay node, according to the extension of the D2D mode to the case of device-to-many devices. Moreover, in our case, the source selects the device to act as the relay among different users of the multicast group by taking into account both the propagation link conditions and the relay social-trust level with the constraint of minimizing the end-to-end content delivery delay. An optimization procedure is also proposed in order to achieve the best performance. Finally, numerical results are provided to highlight the advantages of considering the impact of social level on the end-to-end delivery delay in the integrated social–physical network in comparison with the classical relay-assisted multicast communications for which the relay social-trust level is not considered.

Counterfactual quantum cryptography network with untrusted relay

Science.gov (United States)

Chen, Yuanyuan; Gu, Xuemei; Jiang, Dong; Xie, Ling; Chen, Lijun

2015-07-01

Counterfactual quantum cryptography allows two remote parties to share a secret key even though a physical particle is not in fact transmitted through the quantum channel. In order to extend the scope of counterfactual quantum cryptography, we use an untrusted relay to construct a multi-user network. The implementation issues are discussed to show that the scheme can be realized with current technologies. We also prove the practical security advantages of the scheme by eliminating the probability that an eavesdropper can directly access the signal or an untrusted relay can perform false operations.

Generator for X-ray diagnostics with mAs-relay

International Nuclear Information System (INIS)

Franke, K.

1978-01-01

The invention concerns a generator for X-ray diagnostics with mAs-relay, which is provided with organ keys for organ-programmed selection of mAs-products. For individual setting of the recording time the mAs-relay input is connected to an auxiliary source of current supplying a constant auxiliary current. The response barrier of the mAs-relay is thereby set by time set average. For overload protection may be used a power circuit which at exceeding the programmed times, e.g. the times provided for tomography operation, reduces the X-ray tube power step by step to allowed values by means of the X-ray tube current. (orig.) [de

Throughput maximization for buffer-aided hybrid half-/full-duplex relaying with self-interference

KAUST Repository

Khafagy, Mohammad Galal

2015-06-01

In this work, we consider a two-hop cooperative setting where a source communicates with a destination through an intermediate relay node with a buffer. Unlike the existing body of work on buffer-aided half-duplex relaying, we consider a hybrid half-/full-duplex relaying scenario with loopback interference in the full-duplex mode. Depending on the channel outage and buffer states that are assumed available at the transmitters, the source and relay may either transmit simultaneously or revert to orthogonal transmission. Specifically, a joint source/relay scheduling and relaying mode selection mechanism is proposed to maximize the end-to-end throughput. The throughput maximization problem is converted to a linear program where the exact global optimal solution is efficiently obtained via standard convex/linear numerical optimization tools. Finally, the theoretical findings are corroborated with event-based simulations to provide the necessary performance validation.

Outage Probability versus Fairness Trade-off in Opportunistic Relay Selection with Outdated CSI

Directory of Open Access Journals (Sweden)

Vicario JoseLopez

2009-01-01

Full Text Available We analyze the existing trade-offs in terms of system performance versus fairness of a cooperative system based on opportunistic relay selection (ORS and with outdated channel state information (CSI. In particular, system performance is analytically evaluated in terms of outage probability, and the fairness behavior is assessed based on the power consumption at the different relays. In order to improve the fairness behavior of ORS while keeping the selection diversity gain, we propose a relay selection mechanism where the relay with the highest normalized signal-to-noise ratio (SNR is selected for relaying the source's information. The proposed strategy is compared with existing relay selection strategies by adopting a novel graphical representation inspired by expected profit versus risk plots used in modern portfolio theory. As shown in the paper, this strategy allows operating the system in more favorable points of the outage versus fairness region.

Precoder Design and Power Allocation for MIMO Cognitive Radio Two-Way Relaying Systems

KAUST Repository

Sboui, Lokman

2016-08-11

In this paper, we study a multiple-antenna two-way relaying (TWR) cognitive radio (CR) system. A space alignment (SA) technique is adopted by the secondary users (SUs) to avoid interference with the primary users (PUs). We derive the optimal power allocation that maximizes the TWR achievable SU sum- rate while respecting the total power budget and the relay power constraints. We also analyze the case in which the relay is able to optimize its gain matrix structure to enhance the SU sum-rate. In the numerical results, we quantify the sum-rate gain of using the SA in the TWR CR and we show that the SU sum-rate is very limited when the relay power is low or the PU power and its resulting interference are high. In addition, we optimize the relay gain using an iterative algorithm and compare between different relay matrix structures.

Cyclic AMP Inhibits the Activity and Promotes the Acetylation of Acetyl-CoA Synthetase through Competitive Binding to the ATP/AMP Pocket.

Science.gov (United States)

Han, Xiaobiao; Shen, Liqiang; Wang, Qijun; Cen, Xufeng; Wang, Jin; Wu, Meng; Li, Peng; Zhao, Wei; Zhang, Yu; Zhao, Guoping

2017-01-27

The high-affinity biosynthetic pathway for converting acetate to acetyl-coenzyme A (acetyl-CoA) is catalyzed by the central metabolic enzyme acetyl-coenzyme A synthetase (Acs), which is finely regulated both at the transcriptional level via cyclic AMP (cAMP)-driven trans-activation and at the post-translational level via acetylation inhibition. In this study, we discovered that cAMP directly binds to Salmonella enterica Acs (SeAcs) and inhibits its activity in a substrate-competitive manner. In addition, cAMP binding increases SeAcs acetylation by simultaneously promoting Pat-dependent acetylation and inhibiting CobB-dependent deacetylation, resulting in enhanced SeAcs inhibition. A crystal structure study and site-directed mutagenesis analyses confirmed that cAMP binds to the ATP/AMP pocket of SeAcs, and restrains SeAcs in an open conformation. The cAMP contact residues are well conserved from prokaryotes to eukaryotes, suggesting a general regulatory mechanism of cAMP on Acs. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

The growing landscape of lysine acetylation links metabolism and cell signalling

DEFF Research Database (Denmark)

Choudhary, Chuna Ram; Weinert, Brian Tate; Nishida, Yuya

2014-01-01

Lysine acetylation is a conserved protein post-translational modification that links acetyl-coenzyme A metabolism and cellular signalling. Recent advances in the identification and quantification of lysine acetylation by mass spectrometry have increased our understanding of lysine acetylation...

PPM-based relay communication schemes for wireless body area networks

NARCIS (Netherlands)

Zhang, P.; Willems, F.M.J.; Huang, Li

2012-01-01

This paper investigates cooperative communication schemes based on a single relay with pulse-position modulation (PPM) signaling, for enhancing energy efficiency of wireless body area networks (WBANs) in noncoherent channel settings. We explore cooperation between the source and the relay such that

Protective Relay Studies for the Nigerian National Electric 330 KV ...

African Journals Online (AJOL)

The fundamental reasons for requiring these specific protective relaying features are also reviewed. Other protective relaying schemes that can accomplish the same basic protection objectives are presented. Based on the Nigerian special system characteristics, schemes to correct existing protection inadequacies are ...

On the benefits of location-based relay selection in mobile wireless networks

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Madsen, Tatiana Kozlova; Schwefel, Hans-Peter

2016-01-01

We consider infrastructure-based mobile networks that are assisted by a single relay transmission where both the downstream destination and relay nodes are mobile. Selecting the optimal transmission path for a destination node requires up-to-date link quality estimates of all relevant links....... If the relay selection is based on link quality measurements, the number of links to update grows quadratically with the number of nodes, and measurements need to be updated frequently when nodes are mobile. In this paper, we consider a location-based relay selection scheme where link qualities are estimated...... from node positions; in the scenario of a node-based location system such as GPS, the location-based approach reduces signaling overhead, which in this case only grows linearly with the number of nodes. This paper studies these two relay selection approaches and investigates how they are affected...

Performance Analysis of Relays in LTE for a Realistic Suburban Deployment Scenario

DEFF Research Database (Denmark)

Coletti, Claudio; Mogensen, Preben; Irmer, Ralf

2011-01-01

Relays are likely to play an important role in the deployment of Beyond 3G networks, such as LTE-Advanced, thanks to the possibility of effectively extending Macro network coverage and fulfilling the expected high data-rate requirements. Up until now, the relay technology potential and its cost......-effectiveness have been widely investigated in the literature, considering mainly statistical deployment scenarios, like regular networks with uniform traffic distribution. This paper is envisaged to illustrate the performances of different relay technologies (In-Band/Out-band) in a realistic suburban network...... scenario with real Macro site positions, user density map and spectrum band availability. Based on a proposed heuristic deployment algorithm, results show that deploying In-band relays can significantly reduce the user outage if high backhaul link quality is ensured, whereas Out-band relaying and the usage...

An automated thermoelectric power apparatus using electro-optic relays

International Nuclear Information System (INIS)

Chakravarti, A.; Ranganathan, R.

1992-01-01

We report the design and construction of a thermoelectric power apparatus using home-made electro-optic relays with Z-80A microprocessor for automatic data acquisition and control. The advantages of such relays made out of LED-LDR combinations for the measurement of ΔE and ΔT are discussed in details. (author). 7 refs., 5 figs

Alternate MIMO AF relaying networks with interference alignment: Spectral efficient protocol and linear filter design

KAUST Repository

Park, Kihong

2013-02-01

In this paper, we study a two-hop relaying network consisting of one source, one destination, and three amplify-and-forward (AF) relays with multiple antennas. To compensate for the capacity prelog factor loss of 1/2$ due to the half-duplex relaying, alternate transmission is performed among three relays, and the inter-relay interference due to the alternate relaying is aligned to make additional degrees of freedom. In addition, suboptimal linear filter designs at the nodes are proposed to maximize the achievable sum rate for different fading scenarios when the destination utilizes a minimum mean-square error filter. © 1967-2012 IEEE.

Line Differential Protection Scheme Modelling for Underground 420 kV Cable Systems, EMTDC/PSCAD Relays Modelling

DEFF Research Database (Denmark)

Bak, Claus Leth; Sztykiel, Michal; Dollerup, Sebastian

2011-01-01

Based on the analysis of a specific relay model and an HVAC (High Voltage Alternating Current) cable system, a new approach to EMTDC/PSCAD modelling of protective relays is presented. Such approach allows creating complex and accurate relay models derived from the original algorithms. Relay models...... can be applied with various systems, allowing obtaining the most optimal configuration of the protective relaying. The present paper describes modelling methodology on the basis of Siemens SIPROTEC 4 7SD522/610. Relay model was verified experimentally with its real equivalent by both EMTP......-simulated and real world generated current signals connected to the relay....

Investigation of acetyl migrations in furanosides

Directory of Open Access Journals (Sweden)

Migaud ME

2006-07-01

Full Text Available Abstract Standard reaction conditions for the desilylation of acetylated furanoside (riboside, arabinoside and xyloside derivatives facilitate acyl migration. Conditions which favour intramolecular and intermolecular mechanisms have been identified with intermolecular transesterifications taking place under mild basic conditions when intramolecular orthoester formations are disfavoured. In acetyl ribosides, acyl migration could be prevented when desilylation was catalysed by cerium ammonium nitrate.

Synthesis of polyrotaxanes from acetyl-β-cyclodextrin

Science.gov (United States)

Ristić, I. S.; Nikolić, L.; Nikolić, V.; Ilić, D.; Budinski-Simendić, J.

2011-12-01

Polyrotaxanes are intermediary products in the synthesis of topological gels. They are created by inclusion complex formation of hydrophobic linear macromolecules with cyclodextrins or their derivatives. Then, pairs of cyclodextrin molecules with covalently linkage were practically forming the nodes of the semi-flexible polymer network. Such gels are called topological gels and they can absorb huge quantities of water due to the net flexibility allowing the poly(ethylene oxide) chains to slide through the cyclodextrin cavities, without being pulled out altogether. For polyrotaxane formation poly(ethylene oxide) was used like linear macromolecules. There are hydroxyl groups at poly(ethylene oxide) chains, whereby the linking of the voluminous molecules should be made. To avoid the reaction of cyclodextrin OH groups with stoppers, they should be protected by, e.g., acetylation. In this work, the acetylation of the OH groups of β-cyclodextrin was performed by acetic acid anhydride with iodine as the catalyst. The acetylation reaction was assessed by the FTIR and HPLC method. By the HPLC analysis was found that the acetylation was completed in 20 minutes. Inserting of poly(ethylene oxide) with 4000 g/mol molecule mass into acetyl-β-cyclodextrin with 2:1 poly(ethylene oxide) monomer unit to acetyl-β-cyclodextrin ratio was also monitored by FTIR, and it was found that the process was completed in 12 h at the temperature of 10°C. If the process is performed at temperatures above 10°C, or for periods longer than 12 hours, the process of uncontrolled hydrolysis of acetate groups was initiated.

Cache Aided Decode-and-Forward Relaying Networks: From the Spatial View

Directory of Open Access Journals (Sweden)

Junjuan Xia

2018-01-01

Full Text Available We investigate cache technique from the spatial view and study its impact on the relaying networks. In particular, we consider a dual-hop relaying network, where decode-and-forward (DF relays can assist the data transmission from the source to the destination. In addition to the traditional dual-hop relaying, we also consider the cache from the spatial view, where the source can prestore the data among the memories of the nodes around the destination. For the DF relaying networks without and with cache, we study the system performance by deriving the analytical expressions of outage probability and symbol error rate (SER. We also derive the asymptotic outage probability and SER in the high regime of transmit power, from which we find the system diversity order can be rapidly increased by using cache and the system performance can be significantly improved. Simulation and numerical results are demonstrated to verify the proposed studies and find that the system power resources can be efficiently saved by using cache technique.

Structure, morphology and functionality of acetylated and oxidised barley starches.

Science.gov (United States)

El Halal, Shanise Lisie Mello; Colussi, Rosana; Pinto, Vânia Zanella; Bartz, Josiane; Radunz, Marjana; Carreño, Neftali Lenin Villarreal; Dias, Alvaro Renato Guerra; Zavareze, Elessandra da Rosa

2015-02-01

Acetylation and oxidation are chemical modifications which alter the properties of starch. The degree of modification of acetylated and oxidized starches is dependent on the catalyst and active chlorine concentrations, respectively. The objective of this study was to evaluate the effect of acetylation and oxidation on the structural, morphological, physical-chemical, thermal and pasting properties of barley starch. Barley starches were acetylated at different catalyst levels (11%, 17%, and 23% of NaOH solution) and oxidized at different sodium hypochlorite concentrations (1.0%, 1.5%, and 2.0% of active chlorine). Fourier-transformed infrared spectroscopy (FTIR), X-ray diffractograms, thermal, morphological, and pasting properties, swelling power and solubility of starches were evaluated. The degree of substitution (DS) of the acetylated starches increased with the rise in catalyst concentration. The percentage of carbonyl (CO) and carboxyl (COOH) groups in oxidized starches also increased with the rise of active chlorine level. The presence of hydrophobic acetyl groups, carbonyl and carboxyl groups caused a partial disorganization and depolymerization of starch granules. The structural, morphological and functional changes in acetylated and oxidized starches varied according to reaction conditions. Acetylation makes barley starch more hydrophobic by the insertion of acetyl groups. Also the oxidation promotes low retrogradation and viscosity. All these characteristics are important for biodegradable film production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Lysine Acetylation of CREBH Regulates Fasting-Induced Hepatic Lipid Metabolism

Science.gov (United States)

Kim, Hyunbae; Mendez, Roberto; Chen, Xuequn; Fang, Deyu

2015-01-01

Cyclic AMP-responsive element-binding protein 3-like 3, hepatocyte specific (CREBH), is a hepatic transcription factor that functions as a key regulator of energy homeostasis. Here, we defined a regulatory CREBH posttranslational modification process, namely, lysine-specific acetylation, and its functional involvement in fasting-induced hepatic lipid metabolism. Fasting induces CREBH acetylation in mouse livers in a time-dependent manner, and this event is critical for CREBH transcriptional activity in regulating hepatic lipid homeostasis. The histone acetyltransferase PCAF-mediated acetylation and the deacetylase sirtuin-1-mediated deacetylation coexist to maintain CREBH acetylation states under fasting conditions. Site-directed mutagenesis and functional analyses revealed that the lysine (K) residue at position 294 (K294) within the bZIP domain of the CREBH protein is the site where fasting-induced acetylation/deacetylation occurs. Introduction of the acetylation-deficient (K294R) or acetylation-mimicking (K294Q) mutation inhibited or enhanced CREBH transcriptional activity, respectively. Importantly, CREBH acetylation at lysine 294 was required for the interaction and synergy between CREBH and peroxisome proliferator-activated receptor α (PPARα) in activating their target genes upon fasting or glucagon stimulation. Introduction of the CREBH lysine 294 mutation in the liver leads to hepatic steatosis and hyperlipidemia in animals under prolonged fasting. In summary, our study reveals a molecular mechanism by which fasting or glucagon stimulation modulates lipid homeostasis through acetylation of CREBH. PMID:26438600

Diversity-Multiplexing Trade-off for Coordinated Direct and Relay Schemes

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar; De Carvalho, Elisabeth

2013-01-01

The recent years have brought a significant body of research on wireless Two-Way Relaying (TWR), where the use of network coding brings an evident advantage in terms of data rates. Yet, TWR scenarios represent only a special case and it is of interest to devise similar techniques in more general...... Direct/Relay (CDR) schemes, which involve two flows, of a direct and a relayed user. In this paper we characterize a CDR scheme by deriving/bounding the Diversity-Multiplexing Trade-off (DMT) function. Two cases are considered. In the first case a transmitter knows the Channel State Information (CSI...

NRC Information No. 88-98: Electrical relay degradation caused by oxidation of contact surfaces

International Nuclear Information System (INIS)

Rossi, C.E.

1992-01-01

The NRC staff was recently informed by Clinton Power Station that a reactor scram on June 24, 1988, was caused by an electrical relay failure from oxide buildup on relay contact surfaces. Other information on relay failure from contact oxidation indicates that this problem may be more prevalent than previously thought. For example, a July 17, 1988, 10 CFR Part 21 report from Palo Verde, Unit 2, reported relay failures from contact oxidation that were due to the low current application of the relays. The relay contact surfaces in both of these examples are silver-nickel alloys, and both applications were for low current (i.e., milli-ampere current). Electrical relay contacts made of silver-nickel or silver-cadmium alloys will oxidize (tarnish) when used in low current applications because of the absence of contact surface sparking from the typical relay contact ''making and breaking'' functions. The sparking in the contact surfaces promotes a self-cleaning mechanism that reduces the tarnish buildup on the silver-nickel or silver-cadmium contacts. Discussions with one relay manufacturer revealed that the normal industry practice for low current circuit applications is either to use a contact surface material that will not oxidize or to compensate for the oxidation by increased maintenance activities to ensure reliability. The applied voltage may also influence contact oxidation

The biology of lysine acetylation integrates transcriptional programming and metabolism

Directory of Open Access Journals (Sweden)

Mujtaba Shiraz

2011-03-01

Full Text Available Abstract The biochemical landscape of lysine acetylation has expanded from a small number of proteins in the nucleus to a multitude of proteins in the cytoplasm. Since the first report confirming acetylation of the tumor suppressor protein p53 by a lysine acetyltransferase (KAT, there has been a surge in the identification of new, non-histone targets of KATs. Added to the known substrates of KATs are metabolic enzymes, cytoskeletal proteins, molecular chaperones, ribosomal proteins and nuclear import factors. Emerging studies demonstrate that no fewer than 2000 proteins in any particular cell type may undergo lysine acetylation. As described in this review, our analyses of cellular acetylated proteins using DAVID 6.7 bioinformatics resources have facilitated organization of acetylated proteins into functional clusters integral to cell signaling, the stress response, proteolysis, apoptosis, metabolism, and neuronal development. In addition, these clusters also depict association of acetylated proteins with human diseases. These findings not only support lysine acetylation as a widespread cellular phenomenon, but also impel questions to clarify the underlying molecular and cellular mechanisms governing target selectivity by KATs. Present challenges are to understand the molecular basis for the overlapping roles of KAT-containing co-activators, to differentiate between global versus dynamic acetylation marks, and to elucidate the physiological roles of acetylated proteins in biochemical pathways. In addition to discussing the cellular 'acetylome', a focus of this work is to present the widespread and dynamic nature of lysine acetylation and highlight the nexus that exists between epigenetic-directed transcriptional regulation and metabolism.

Simulation of Distance Relay for Load Encroachment Alleviation with Agent Based Supervision of Zone3

Directory of Open Access Journals (Sweden)

Mohamed Badr

2017-03-01

Full Text Available Cascaded tripping of power lines due to mal-operation of zone-3 distance relays has been one of the main causes of many previous blackouts worldwide. Encroachment of load into zone-3 characteristics during stressed system operation conditions is a basic factor for such mal-operation of the relays. By improving the operation of zone-3, it is possible to prevent mal-operations so that cascaded line tripping can be avoided. For proper study of the behavior of distance relay during faults and load encroachment phenomenon, we must build a model of distance relay, so in this paper a modeling study of distance relay is implemented using MATLAB/Simulink program. However, this model is distinguished from previous models that, examines in detail the third zone of distance relay. Many cases are simulated with changing line loading and fault location to ensure the capability of the relay to detect the fault and thus the maximum load ability limit of distance relay is obtained. In order to prevent cascading events caused by hidden failures in zone-3 relays, agent based relay architectures have been suggested in the recent past. In such architectures each zone-3 relay contains agents that require communication with other agents at various relevant relays in order to distinguish a real zone-3 event from a temporary overload. In this paper, a local master agent is consulted by all zone-3 agents before a tripping decision is made. The master agent maintains a rule base which is updated based on the local topology of the network and real time monitoring of the status of other relays and circuit breakers. Cisco Packet Tracer program is used for running communication network simulations. The result of the simulation indicate that the time estimated to send and receive a packet data unit (PDU message between one relay to anther can satisfy the communication requirement for the proposed scheme with fiber media.

On Amplify-and-Forward Relaying Over Hyper-Rayleigh Fading Channels

Directory of Open Access Journals (Sweden)

S. H. Alvi

2014-12-01

Full Text Available Relayed transmission holds promise for the next generation of wireless communication systems due to the performance gains it can provide over non-cooperative systems. Recently hyper-Rayleigh fading, which represents fading conditions more severe than Rayleigh fading, has received attention in the context of many practical communication scenarios. Though power allocation for Amplify-and-Forward (AF relaying networks has been studied in the literature, a theoretical analysis of the power allocation problem for hyper-Rayleigh fading channels is a novel contribution of this work. We develop an optimal power allocation (OPA strategy for a dual-hop AF relaying network in which the relay-destination link experiences hyper-Rayleigh fading. A new closed-form expression for the average signal-to-noise ratio (SNR at destination is derived and it is shown to provide a new upper-bound on the average SNR at destination, which outperforms a previously proposed upper-bound based on the well-known harmonic-geometric mean inequality. An OPA across the source and relay nodes, subject to a sum-power constraint, is proposed and it is shown to provide measurable performance gains in average SNR and SNR outage at the destination relative to the case of equal power allocation.

Partial relay selection based on shadowing side information over generalized composite fading channels

KAUST Repository

Yilmaz, Ferkan

2011-11-01

In this paper, in contrast to the relay selection protocols available in the literature, we propose a partial relay selection protocol utilizing only the shadowing side information of the relays instead of their full channel side information in order to select a relay in a dual-hop relaying system through the available limited feedback channels and power budget. We then presented an exact unified performance expression combining the average bit error probability, ergodic capacity, and moments-generating function of the proposed partial relay selection over generalized fading channels. Referring to the unified performance expression introduced in [1], we explicitly offer a generic unified performance expression that can be easily calculated and that is applicable to a wide variety of fading scenarios. Finally, as an illustration of the mathematical formalism, some numerical and simulation results are generated for an extended generalized-K fading environment, and these numerical and simulation results are shown to be in perfect agreement. © 2011 IEEE.

A study of optimization problem for amplify-and-forward relaying over weibull fading channels

KAUST Repository

Ikki, Salama Said; Aissa, Sonia

2010-01-01

This paper addresses the power allocation and relay positioning problems in amplify-and-forward cooperative networks operating in Weibull fading environments. We study adaptive power allocation (PA) with fixed relay location, optimal relay location

CERN Relay Race 2018

CERN Document Server

CERN Running club

2018-01-01

The CERN running club, in collaboration with the Staff Association, is happy to announce the 2018 relay race edition. It will take place on Thursday, May 24th and will consist as every year in a round trip of the CERN Meyrin site in teams of 6 members. It is a fun event, and you do not have to run fast to enjoy it. Registrations will be open from May 1st to May 22nd on the running club web site. All information concerning the race and the registration are available there too: http://runningclub.web.cern.ch/content/cern-relay-race. A video of the previous edition is also available here : http://cern.ch/go/Nk7C. As every year, there will be animations starting at noon on the lawn in front of restaurant 1, and information stands for many CERN associations and clubs will be available. The running club partners will also be participate in the event, namely Berthie Sport, Interfon and Uniqa.

Relays undergo seismic tests

International Nuclear Information System (INIS)

Burton, J.C.

1977-01-01

Utilities are required by the Nuclear Regulatory Commission to document that seismic vibration will not adversely affect critical electrical equipment. Seismic testing should be designed to determine the malfunction level (fragility testing). Input possibilities include a continuous sine, a decaying sine, a sine beat, random vibrations, and combinations of random vibrations and sine beat. The sine beat most accurately simulates a seismic event. Test frequencies have a broad range in order to accommodate a variety of relay types and cabinet mounting. Simulation of motion along three axes offers several options, but is best achieved by three in-phase single-axis vibration machines that are less likely to induce testing fatigue failure. Consensus on what constitutes relay failure favors a maximum two microsecond discontinuity. Performance tests should be conducted for at least two of the following: (1) nonoperating modes, (2) operating modes, or (3) the transition above the two modes, with the monitoring mode documented for all three. Results should specify a capability curve of maximum safe seismic acceleration and a graph plotting acceleration with sine-beat frequency

Error-rate performance analysis of cooperative OFDMA system with decode-and-forward relaying

KAUST Repository

Fareed, Muhammad Mehboob; Uysal, Murat; Tsiftsis, Theodoros A.

2014-01-01

In this paper, we investigate the performance of a cooperative orthogonal frequency-division multiple-access (OFDMA) system with decode-and-forward (DaF) relaying. Specifically, we derive a closed-form approximate symbol-error-rate expression and analyze the achievable diversity orders. Depending on the relay location, a diversity order up to (LSkD + 1) + σ M m = 1 min(LSkRm + 1, LR mD + 1) is available, where M is the number of relays, and LS kD + 1, LSkRm + 1, and LRmD + 1 are the lengths of channel impulse responses of source-to-destination, source-to- mth relay, and mth relay-to-destination links, respectively. Monte Carlo simulation results are also presented to confirm the analytical findings. © 2013 IEEE.

Error-rate performance analysis of cooperative OFDMA system with decode-and-forward relaying

KAUST Repository

Fareed, Muhammad Mehboob

2014-06-01

In this paper, we investigate the performance of a cooperative orthogonal frequency-division multiple-access (OFDMA) system with decode-and-forward (DaF) relaying. Specifically, we derive a closed-form approximate symbol-error-rate expression and analyze the achievable diversity orders. Depending on the relay location, a diversity order up to (LSkD + 1) + σ M m = 1 min(LSkRm + 1, LR mD + 1) is available, where M is the number of relays, and LS kD + 1, LSkRm + 1, and LRmD + 1 are the lengths of channel impulse responses of source-to-destination, source-to- mth relay, and mth relay-to-destination links, respectively. Monte Carlo simulation results are also presented to confirm the analytical findings. © 2013 IEEE.

Accurate performance analysis of opportunistic decode-and-forward relaying

KAUST Repository

Tourki, Kamel

2011-07-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may be considered unusable, and the destination may use a selection combining technique. We first derive the exact statistics of each hop, in terms of probability density function (PDF). Then, the PDFs are used to determine accurate closed form expressions for end-to-end outage probability for a transmission rate R. Furthermore, we evaluate the asymptotical performance analysis and the diversity order is deduced. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over different network architectures. © 2011 IEEE.

Reliability Analysis of Differential Relay as Main Protection Transformer Using Fuzzy Logic Algorithm

Science.gov (United States)

Mulyadi, Y.; Sucita, T.; Sumarto; Alpani, M.

2018-02-01

Electricity supply demand is increasing every year. It makes PT. PLN (Persero) is required to provide optimal customer service and satisfaction. Optimal service depends on the performance of the equipment of the power system owned, especially the transformer. Power transformer is an electrical equipment that transforms electricity from high voltage to low voltage or vice versa. However, in the electrical power system, is inseparable from interference included in the transformer. But, the disturbance can be minimized by the protection system. The main protection transformer is differential relays. Differential relays working system using Kirchoff law where inflows equal outflows. If there are excessive currents that interfere then the relays will work. But, the relay can also experience decreased performance. Therefore, this final project aims to analyze the reliability of the differential relay on the transformer in three different substations. Referring to the standard applied by the transmission line protection officer, the differential relay shall have slope characteristics of 30% in the first slope and 80% in the second slope when using two slopes and 80% when using one slope with an instant time and the corresponding ratio. So, the results obtained on the Siemens differential release have a reliable slope characteristic with a value of 30 on the fuzzy logic system. In a while, ABB a differential relay is only 80% reliable because two experiments are not reliable. For the time, all the differential relays are instant with a value of 0.06 on the fuzzy logic system. For ratios, the differential relays ABB have a better value than others brand with a value of 151 on the fuzzy logic system.

Tests of microprocessor-based relay protection devices: Problems and solutions

Directory of Open Access Journals (Sweden)

Gurevich Vladimir

2009-01-01

Full Text Available Usually, the operational condition of relay protection devices is checked with specific settings used for the relay operation in a certain network point. In the author's opinion in order to verify the proper operation of complex multifunctional microprocessor-based protection devices (MPD at their inspection, start-up after repairs or during periodic tests there is no need to use the actual settings at which the relay is to be operated in a certain network's point. It should be tested for proper operation at several of its most critical preset characteristic points as well as in several preset characteristics constituting its most complicated (combined operation modes, including the dynamic operation modes with preset transition processes specific for standard power networks (not necessarily for a specific point. The proposed set of actions for the unification of software platforms of the modern, microprocessor-based relay protection test systems will enable examination of modern MPD in an absolutely new way. .

Acetyl coenzyme A synthetase is acetylated on multiple lysine residues by a protein acetyltransferase with a single Gcn5-type N-acetyltransferase (GNAT) domain in Saccharopolyspora erythraea.

Science.gov (United States)

You, Di; Yao, Li-Li; Huang, Dan; Escalante-Semerena, Jorge C; Ye, Bang-Ce

2014-09-01

Reversible lysine acetylation (RLA) is used by cells of all domains of life to modulate protein function. To date, bacterial acetylation/deacetylation systems have been studied in a few bacteria (e.g., Salmonella enterica, Bacillus subtilis, Escherichia coli, Erwinia amylovora, Mycobacterium tuberculosis, and Geobacillus kaustophilus), but little is known about RLA in antibiotic-producing actinomycetes. Here, we identify the Gcn5-like protein acetyltransferase AcuA of Saccharopolyspora erythraea (SacAcuA, SACE_5148) as the enzyme responsible for the acetylation of the AMP-forming acetyl coenzyme A synthetase (SacAcsA, SACE_2375). Acetylated SacAcsA was deacetylated by a sirtuin-type NAD(+)-dependent consuming deacetylase (SacSrtN, SACE_3798). In vitro acetylation/deacetylation of SacAcsA enzyme was studied by Western blotting, and acetylation of lysine residues Lys(237), Lys(380), Lys(611), and Lys(628) was confirmed by mass spectrometry. In a strain devoid of SacAcuA, none of the above-mentioned Lys residues of SacAcsA was acetylated. To our knowledge, the ability of SacAcuA to acetylate multiple Lys residues is unique among AcuA-type acetyltransferases. Results from site-specific mutagenesis experiments showed that the activity of SacAcsA was controlled by lysine acetylation. Lastly, immunoprecipitation data showed that in vivo acetylation of SacAcsA was influenced by glucose and acetate availability. These results suggested that reversible acetylation may also be a conserved regulatory posttranslational modification strategy in antibiotic-producing actinomycetes. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2011-01-01

In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. © 2011 IEEE.

Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

KAUST Repository

Tourki, Kamel

2010-10-01

In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end biterror rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. ©2010 IEEE.

Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2010-01-01

In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end biterror rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. ©2010 IEEE.

Location-quality-aware policy optimisation for relay selection in mobile networks

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Olsen, Rasmus Løvenstein; Madsen, Tatiana Kozlova

2016-01-01

for resulting performance of such network optimizations. In mobile scenarios, the required information collection and forwarding causes delays that will additionally affect the reliability of the collected information and hence will influence the performance of the relay selection method. This paper analyzes...... the joint influence of these two factors in the decision process for the example of a mobile location-based relay selection approach using a continuous time Markov chain model. Efficient algorithms are developed based on this model to obtain optimal relay policies under consideration of localization errors....... Numerical results show how information update rates, forwarding delays, and location estimation errors affect these optimal policies and allow to conclude on the required accuracy of location-based systems for such mobile relay selection scenarios. A measurement-based indoor scenario with more complex...

Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

KAUST Repository

Tourki, Kamel

2011-06-01

In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. © 2011 IEEE.

Mode of action of Fusarium moniliforme endopolygalacturonase towards acetylated pectin.

NARCIS (Netherlands)

Bonnin, E.; Alebeek, van G.J.W.M.; Voragen, A.G.J.; Thibault, J.F.

2003-01-01

Endopolygalacturonase from Fusarium moniliforme was used to degrade acetylated homogalacturonan previously prepared from sugar beet pulp. The initial velocity and the final percentage of hydrolysis decreased-very rapidly with increasing degree of acetylation, showing that acetyl substitution

49 CFR 236.206 - Battery or power supply with respect to relay; location.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Battery or power supply with respect to relay..., AND APPLIANCES Automatic Block Signal Systems Standards § 236.206 Battery or power supply with respect to relay; location. The battery or power supply for each signal control relay circuit, where an open...

47 CFR 64.606 - VRS and IP Relay provider and TRS program certification.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 3 2010-10-01 2010-10-01 false VRS and IP Relay provider and TRS program... Services and Related Customer Premises Equipment for Persons With Disabilities § 64.606 VRS and IP Relay... including notification in the Federal Register. (2) VRS and IP Relay provider. Any entity desiring to...

Deep space optical communication via relay satellite

Science.gov (United States)

Dolinar, S.; Vilnrotter, V.; Gagliardi, R.

1981-01-01

The application of optical communications for a deep space link via an earth-orbiting relay satellite is discussed. The system uses optical frequencies for the free-space channel and RF links for atmospheric transmission. The relay satellite is in geostationary orbit and contains the optics necessary for data processing and formatting. It returns the data to earth through the RF terrestrial link and also transmits an optical beacon to the satellite for spacecraft return pointing and for the alignment of the transmitting optics. Future work will turn to modulation and coding, pointing and tracking, and optical-RF interfacing.

2005 CERN Relay Race

CERN Multimedia

Patrice Loiez

2005-01-01

The CERN Relay Race takes place each year in May and sees participants from all areas of the CERN staff. The winners in 2005 were The Shabbys with Los Latinos Volantes in second and Charmilles Technologies a close third. To add a touch of colour and levity, the CERN Jazz Club provided music at the finishing line.

CPLA 1.0: an integrated database of protein lysine acetylation.