Biodegradation of isopropanol and acetone under denitrifying conditions by Thauera sp. TK001 for nitrate-mediated microbially enhanced oil recovery.

Science.gov (United States)

Fida, Tekle Tafese; Gassara, Fatma; Voordouw, Gerrit

2017-07-15

Amendment of reservoir fluid with injected substrates can enhance the growth and activity of microbes. The present study used isopropyl alcohol (IPA) or acetone to enhance the indigenous anaerobic nitrate-reducing bacterium Thauera sp. TK001. The strain was able to grow on IPA or acetone and nitrate. To monitor effects of strain TK001 on oil recovery, sand-packed columns containing heavy oil were flooded with minimal medium at atmospheric or high (400psi) pressure. Bioreactors were then inoculated with 0.5 pore volume (PV) of minimal medium containing Thauera sp. TK001 with 25mM of acetone or 22.2mM of IPA with or without 80mM nitrate. Incubation without flow for two weeks and subsequent injection with minimal medium gave an additional 17.0±6.7% of residual oil in place (ROIP) from low-pressure bioreactors and an additional 18.3% of ROIP from the high-pressure bioreactors. These results indicate that acetone or IPA, which are commonly used organic solvents, are good substrates for nitrate-mediated microbial enhanced oil recovery (MEOR), comparable to glucose, acetate or molasses, tested previously. This technology may be used for coupling biodegradation of IPA and/or acetone in waste streams to MEOR where these waste streams are generated in close proximity to an oil field. Copyright © 2017 Elsevier B.V. All rights reserved.

Electrochemical and Electron Paramagnetic Resonance Study of the Mechanism of Oxidation of Phenazine-di-N-oxide in the Presence of Isopropyl alcohol at Glassy Carbon and Single-Walled Carbon Nanotube Electrodes

International Nuclear Information System (INIS)

Kulakovskaya, S.I.; Kulikov, A.V.; Sviridova, L.N.; Stenina, E.V.

2014-01-01

Graphical abstract: - Highlights: • The mechanism of oxidation of phenazine-di-N-oxide in the presence of isopropyl alcohol was studied. • The results are explained in terms of the E 1 C 1 E 2 C 2 mechanism of the two-stage electrode process. • The total two-electron catalytic oxidation of i-PrOH in the complex with the phenazine-di-N-oxide radical cation was assumed to occur. - Abstract: The mechanism of oxidation of phenazine-di-N-oxide in the presence of isopropyl alcohol was studied by cyclic voltammetry at glassy carbon (GC) and single-walled carbon nanotubes (SWCNT) electrodes in 0.1 M LiClO 4 solutions in acetonitrile. The adsorption of phenazine-di-N-oxide at SWCNT electrode in 0.1 M LiClO 4 solution in acetonitrile was investigated by measurement of the dependence of the differential double layer capacitance of the electrode C on potential E. The effect of isopropyl alcohol on the shape of cyclic voltammograms (CVs) of phenazine-di-N-oxide and the intensity of Electron Paramagnetic Resonance (EPR) signal of its radical cation was investigated. The catalytic currents were recorded at the oxidation of phenazine-di-N-oxide at SWCNT and GC electrodes in the presence of isopropyl alcohol. The results were explained in terms of the E 1 C 1 E 2 C 2 mechanism of two-stage electrode process characterized by catalytic current recorded at the second electrode stage. The overall two-electron catalytic oxidation of isopropyl alcohol in complex with the phenazine-di-N-oxide radical cation was assumed to occur. It was shown that SWCNT electrodes can be used in the electrocatalytic oxidation of organic compounds in the presence of electrochemically generated phenazine-di-N-oxide radical cation

Linear free energy relationships in heterogeneous catalysis--13. The dehydration of aliphatic alcohols over silica-alumina. [N-butyl alcohol, sec. -butyl or isopropyl alcohol, tert. -butyl alcolol

Energy Technology Data Exchange (ETDEWEB)

Take, J; Matsumoto, T; Yoneda, Y

1978-01-01

The dehydration of n-butyl alcohol at 120/sup 0/-166/sup 0/C, sec.-butyl or isopropyl alcohol at 100/sup 0/-145/sup 0/C, and tert.-butyl alcohol at 54/sup 0/-80/sup 0/C, over silica/alumina catalyst was zero order in alcohol at 0.01-0.1 atm, and the activation energies were 35.3, 31.7, 32.0, and 29.9 kcal/mol, respectively. The zero-order rate constants were mainly affected by the activation energies since the preexponential factors varied little except for tert.-butyl alcohol. A linear relationship was found between the activation energy or the logarithm of the zero-order rate constant and the heterolytic bond dissociation energy for the carbon-oxygen bond in alcohols D(R/sup +/OH/sup -/). The activation energy increased and the rate constant decreased with increasing D(R/sup +/OH/sup -/). The results indicate that dehydration is E1 over this catalyst, but a similar correlation was observed based on published data for dehydration over alumina, which follows an E2 mechanism, indicating that heterolytic cleavage of the C-O bond is rate-determining in both mechanisms.

Information draft on the development of air standards for isopropyl benzene

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-01-01

Isopropyl benzene, also commonly referred to as cumene, is a colourless liquid with a sharp, penetrating odour. It is derived from the distillation of coal tar, naphtha and petroleum. It is used mainly as an intermediate in the production of phenol, acetone, and alpha-methyl styrene, all of which are components in plastic resins. Isopropyl benzene is also used as a solvent and thinner for paints and enamels and as an octane booster in aviation gasoline. In 1996, reported atmospheric releases in Canada amounted to 16.4 tonnes, of which 9.1 tonnes were from Ontario sources. Isopropyl benzene is not a significant threat to health in low concentrations. Inhalation exposure can cause dizziness, light-headedness and fainting. Contact with isopropyl benzene can irritate the skin, eyes, nose and mouth. The current Ontario half-hour interim Point of Impingement (OPI) standard and the one-hour Ambient Air Quality Criterion (AAQC) are both set at 100 microgram/cubic meter on the basis of the odour nuisance property of the substance. A review of applicable literature from world-wide sources (and summarized in this report) reveal that four US agencies have developed air quality criteria for isopropyl benzene based on the health effects of the compound. These criteria range from 9 to 585 micrograms/cubic meter for an annual average basis and from 87 to 400 microgram/cubic meter on a 24-hour basis. 40 refs., 1 tab., appendix.

Isobaric (vapour + liquid + liquid) equilibrium data for (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) systems at 100 kPa

International Nuclear Information System (INIS)

Lladosa, Estela; Monton, Juan B.; Burguet, MaCruz; Torre, Javier de la

2008-01-01

Isobaric (vapour + liquid + liquid) equilibria were measured for the (di-n-propyl ether + n-propyl alcohol + water) and (diisopropyl ether + isopropyl alcohol + water) system at 100 kPa. The apparatus used for the determination of (vapour + liquid + liquid) equilibrium data was an all-glass dynamic recirculating still with an ultrasonic homogenizer couple to the boiling flask. The experimental data demonstrated the existence of a heterogeneous ternary azeotrope for both ternary systems. The (vapour + liquid + liquid) equilibria data were found to be thermodynamically consistent for both systems. The experimental data were compared with the estimation using UNIQUAC and NRTL models and the prediction of UNIFAC model

Catalytic hydrogenation of carbonyl group for deuterated compound production

International Nuclear Information System (INIS)

Gluhoi, C. Andreea; Marginean, P.; Lazar, Diana; Almasan, V.

1999-01-01

The total deuterated isopropyl alcohol can be produced starting from acetone. The developed technology comprises two steps: Deuteration of acetone by H/D isotopic exchange between acetone and heavy water in homogeneous catalysis. Reduction of the deuterated acetone with deuterium in presence of a metal/support catalyst. H/D isotopic exchange reaction of the H atoms from CH 3 groups is easy to occur because carbonyl group weakens C-H bond (ceto-enolyc tautomery). The big difference between boiling points of acetone and water permits an easy separation of acetone by distillation method. The reduction of acetone with deuterium was performed in a dynamic reactor by passing a deuterium flow saturated with acetone vapour through a supported nickel catalyst bed. The reaction products were analysed on-line using a flame ionisation detector. The supported nickel catalysts were checked for this reaction. By using nickel over different supports the selectivity for isopropyl alcohol was about 100%. The propane was detected only as traces. The catalytic activity depends strongly on the support nature: the Ni/SiO 2 is less active, while the Ni/TiO 2 presents the larger value for the intrinsic activity. (authors)

Green synthesis of isopropyl myristate in novel single phase medium Part I: Batch optimization studies

Directory of Open Access Journals (Sweden)

Rajeshkumar N. Vadgama

2015-12-01

Full Text Available Isopropyl myristate finds many applications in food, cosmetic and pharmaceutical industries as an emollient, thickening agent, or lubricant. Using a homogeneous reaction phase, non-specific lipase derived from Candida antartica, marketed as Novozym 435, was determined to be most suitable for the enzymatic synthesis of isopropyl myristate. The high molar ratio of alcohol to acid creates novel single phase medium which overcomes mass transfer effects and facilitates downstream processing. The effect of various reaction parameters was optimized to obtain a high yield of isopropyl myristate. Effect of temperature, agitation speed, organic solvent, biocatalyst loading and batch operational stability of the enzyme was systematically studied. The conversion of 87.65% was obtained when the molar ratio of isopropyl alcohol to myristic acid (15:1 was used with 4% (w/w catalyst loading and agitation speed of 150 rpm at 60 °C. The enzyme has also shown good batch operational stability under optimized conditions.

Green synthesis of isopropyl myristate in novel single phase medium Part I: Batch optimization studies.

Science.gov (United States)

Vadgama, Rajeshkumar N; Odaneth, Annamma A; Lali, Arvind M

2015-12-01

Isopropyl myristate finds many applications in food, cosmetic and pharmaceutical industries as an emollient, thickening agent, or lubricant. Using a homogeneous reaction phase, non-specific lipase derived from Candida antartica, marketed as Novozym 435, was determined to be most suitable for the enzymatic synthesis of isopropyl myristate. The high molar ratio of alcohol to acid creates novel single phase medium which overcomes mass transfer effects and facilitates downstream processing. The effect of various reaction parameters was optimized to obtain a high yield of isopropyl myristate. Effect of temperature, agitation speed, organic solvent, biocatalyst loading and batch operational stability of the enzyme was systematically studied. The conversion of 87.65% was obtained when the molar ratio of isopropyl alcohol to myristic acid (15:1) was used with 4% (w/w) catalyst loading and agitation speed of 150 rpm at 60 °C. The enzyme has also shown good batch operational stability under optimized conditions.

Development of technology for the alkylation of hydroquinone with aliphatic alcohols

Directory of Open Access Journals (Sweden)

V. M. Bolotov

2017-01-01

Full Text Available The paper presents the results of research of technology of alkylation of hydroquinone, propyl, isopropyl, isobutyl and tert-butyl alcohols in the presence of concentrated phosphoric acid. The temperature of the alkylation reaction was maintained between 70–72 °С. On the basis of literature data and preliminary investigations the reaction was performed for 4 hours. Upon completion of the reaction, we removed the unreacted hydroquinone, aliphatic alcohol and phosphoric acid are added to a solution of distilled water (solvent corresponding connections and sodium bicarbonate to slightly acidic (pH 5–6. For separation from the reaction medium of alkylhydroquinones in the reaction mixture was added benzene in which the original hydroquinone dissolves much less. Concentration of the benzene extract alkylhydroquinones conducted by Stripping the solvent under vacuum at temperatures above 70 °С in air atmosphere. Higher temperature vacuum distillation AIDS in the oxidation of alkylhydroquinones to alkylphenones. Precipitated after crystallization, alkylhydroquinones were dried under vacuum in a drying pistol at 56 °С. Dried products were identified by defining the melting temperature, the study of spectral characteristics and qualitative reactions with FeCl3. We also studied the solubility of alkylhydroquinones in various solvents, which showed low solubility of alkylhydroquinones in water, benzene, toluene and higher solubility in propyl and isopropyl alcohols and in acetone. Analysis of the results shows that the obtained alkylhydroquinones are not chemically pure compounds, and contain in their composition of admixture source of hydroquinone. Qualitative reactions of solutions of alkylhydroquinones with FeCl3 solution differ from the corresponding reaction of a solution of hydroquinone. The results of investigations of electronic absorption spectra of alkylhydroquinones and source of hydroquinone in isopropyl alcohol solution did not

Effects of temperature and solvent concentration on the solvent crystallization of palm-based dihydroxystearic acid with isopropyl alcohol

Institute of Scientific and Technical Information of China (English)

Gregory F.L.Koay; Teong-Guan Chuah; Sumaiya Zainal-Abidin; Salmiah Ahmad; Thomas S.Y.Choong

2012-01-01

Palm-based dihydroxystearic acid of 69.55％ purity was produced in a 500-kg-per-batch operation pilot plant and purified through solvent crystallization in a custom fabricated simultaneous batch crystallizer unit.The effects of temperature and solvent concentration on yield,particle size distribution and purity were studied.The purity was higher,while the yield and particle size were lower and smaller,respectively,at higher temperature and solvent concentration.The solvent crystallization process efficiency was rated at 66-69％ when carried out with 70-80％ isopropyl alcohol at 20 ℃.

Treatment of chlorofluorocarbons in alcohol solutions by γ-irradiation

International Nuclear Information System (INIS)

Shimokawa, Toshinari; Nakagawa, Seiko; Sawai, Teruko

1995-01-01

A study was done on dechlorination of 1,1,2-trichloro-1,2,2-trifluoroethane (CFC113) in neutral and alkaline alcohol solutions by means of γ-irradiation. The dechlorination yield (G (Cl - )) was found to depend on the kind of alcohol used as solvents and the presence of hydroxide ion. The order of G (Cl - ) value in alkaline solution was isopropyl alcohol>> ethyl alcohol > methyl alcohol. It was suggested that the high yield obtained in alkaline isopropyl alcohol solution is explained by a chain process in dechlorination reaction. In case of alkaline isopropyl alcohol solution, CFC113 was dechlorinated to lower chlorinated ethane, and 1,1-dichloro-1,2,2-trifluoroetane was a main product. We have discussed on the chain dechlorination mechanism in alkaline isopropyl alcohol solution. (author)

Some Biological studies on the Mediterranean Fruit Fly, Ceratitis capitata (Wiedemann) After Egg Exposure to Acetone, Diethyl Ether, Ethyl Alcohol and Pupal Gamma Irradiation

International Nuclear Information System (INIS)

Fadel, A.M.

2000-01-01

Some biological studies of the Mediterranean fruit fly Ceratitis capitata (Wiedemann) were carried out to help in controlling this pest. Three laboratory experiments were done to study the effect of acetone, diethyl ether and ethyl alcohol separately or combined with gamma radiation through egg treatment or larval diet treatment. The gamma dose (90 Gy) was applied only on the produced pupae after egg or larval diet treatment. Concentrations of 0, 25, 50 and 100% of each chemical were applied for treating eggs to evaluate egg hatch, pupation, adult emergence and sex ratio. larval diet treatment was done by adding 20 ml of each chemical concentration to 500 gm of larval diet.Treating eggs with ethyl alcohol separately increased pupation significantly at all concentration used while adult emergence was insignificantly increased with the lowest concentration only (25%). Treating larval diet with ethyl alcohol alone increased pupation insignificantly and adult emergence was insignificantly decreased at different concentrations. Moreover, treating eggs or larval diet with diethyl ether alone significantly increased sex ratio at 50% and 2% concentration, respectively,while differed insignificantly by applying different chemicals either on eggs or on larval diet. Treating eggs with the three chemicals before gamma irradiation of the produced pupae fluctuated egg hatch insignificantly compared to gamma irradiation alone. By applying diethyl ether on eggs or acetone in the larval diet decreased egg hatch insignificantly. Competitiveness values were insignificantly increased by applying ethyl alcohol on eggs, acetone or ethyl alcohol on eggs, acetone or ethyl alcohol in larval diet before gamma irradiation of the produced pupae. Survivals of the produced adults, treated as eggs or in the larval diet with different chemicals and irradiated as pupae, fluctuated insignificantly

Green synthesis of isopropyl myristate in novel single phase medium Part II: Packed bed reactor (PBR) studies

OpenAIRE

Vadgama, Rajeshkumar N.; Odaneth, Annamma A.; Lali, Arvind M.

2015-01-01

Isopropyl myristate is a useful functional molecule responding to the requirements of numerous fields of application in cosmetic, pharmaceutical and food industry. In the present work, lipase-catalyzed production of isopropyl myristate by esterification of myristic acid with isopropyl alcohol (molar ratio of 1:15) in the homogenous reaction medium was performed on a bench-scale packed bed reactors, in order to obtain suitable reaction performance data for upscaling. An immobilized lipase B fr...

Preparation of a nickel nanopowder by wire explosion in liquid media

International Nuclear Information System (INIS)

Cho, Chuhyun; Ha, Yooncheol; Kang, Chungil; Jin, Yunsik; Rim, Geunhie

2010-01-01

Nickel wires of 0.8 mm in diameter and 80 mm in length were electrically exploded in liquid media, such as water, ethyl alcohol, isopropyl alcohol, and acetone. The electrical energy discharged through the wire was 10 kJ. The distribution of particle sizes was broad from a few μm to tens of nanometer, regardless of the liquid medium used in this study. The particles could be classified according to their sizes by using a centrifugal separator. The powder prepared in distilled water showed mainly a pure metallic Ni phase although a little oxide phase was observed in the XRD analysis. However, the powders prepared in ethyl alcohol, isopropyl alcohol, and acetone showed complicated unknown phases, which is attributed to a compound of carbon in the organic liquid. The unknown phase was turned into a pure metallic Ni phase after heat treatment at 400 .deg. C.

Polymerization of allyl alcohol by radiation to obtain microencapsulated structure

International Nuclear Information System (INIS)

Usanmaz, A.; Saricilar, S.

1989-01-01

Allyl alcohol was polymerized by radiation under various conditions. The limiting conversions were about 30 % in bulk, 35 % when containing 0.03 mole fraction AlCl 3 and 50 % when water was contained at 27 % (v/v). Irradiation was done with Co-60 gamma rays at room temperature and under vacuum. The presence of oxygen did not cause any change in the reaction rate. Molecular weights were determined by viscosity and cryoscopic methods. K and α values were found to be 3.57 x 10 -4 and 0.62 for solutions in methanol at 25degC. The polymers up to about 10 % conversion were viscous liquids having microcapsular structures: at high conversions, they became hard and glassy. The microencapsulated structures were also retained in solutions in methanol, acetone, and isopropyl alcohol. The samples were insoluble in water, benzene, and toluence. (author)

A PMMA coated PMN–PT single crystal resonator for sensing chemical agents

International Nuclear Information System (INIS)

Frank, Michael; Kassegne, Sam; Moon, Kee S

2010-01-01

A highly sensitive lead magnesium niobate–lead titanate (PMN–PT) single crystal resonator coated with a thin film of polymethylmethacrylate (PMMA) useful for detecting chemical agents such as acetone, methanol, and isopropyl alcohol is presented. Swelling of the cured PMMA polymer layer in the presence of acetone, methanol, and isopropyl alcohol vapors is sensed as a mass change transduced to an electrical signal by the PMN–PT thickness shear mode sensor. Frequency change in the PMN–PT sensor is demonstrated to vary according to the concentration of the chemical vapor present within the sensing chamber. For acetone, the results indicate a frequency change more than 6000 times greater than that which would be expected from a quartz crystal microbalance coated with PMMA. This study is the first of its kind to demonstrate vapor loading of adsorbed chemical agents onto a polymer coated PMN–PT resonator

trans-Carbonylchloridobis[dicyclohexyl(4-isopropylphenylphosphane]rhodium(I acetone monosolvate

Directory of Open Access Journals (Sweden)

Sizwe Makhoba

2011-09-01

Full Text Available The title rhodium Vaska-type complex, trans-[RhCl{P(C6H112(C6H4-4-C3H72}2(CO], crystallizes with an accompanying acetone solvent molecule. The metal atom shows a distorted square-planar coordination environment with selected important geometrical parameters of Rh—P = 2.3237 (6 and 2.3253 (6 Å, Rh—Cl = 2.3724 (6 Å, Rh—C = 1.802 (2 Å, P—Rh—P = 173.42 (2° and Cl—Rh—C = 179.13 (7°. Effective cone angles for the two P atoms are 165 and 161°, respectively. Both isopropyl groups and the acetone molecule are disordered with occupancy values of 0.523 (5:0.477 (5, 0.554 (8:0.446 (8 and 0.735 (4:0.265 (4, respectively. The crystal packing is stabilized by weak C—H...O and C—H...Cl contacts.

Molecule of the Month

Indian Academy of Sciences (India)

having solutions coloured red in methanol, violet in etha- nol, blue in isopropyl alcohol, green in acetone and green- ish-yellow in anisole. The electronic ... concentrated sulfuric acid to obtain a symmetric triphenylpyrelium. Box 1. Compounds ...

Biomolecular Chemistry of Isopropyl Fibrates

Science.gov (United States)

Rath, Niharika; Kotheimer, Amenda; Miller, Chad; Zeller, Matthias; Rath, Nigam P.

2012-01-01

Isopropyl 2-[4-(4-chlorobenzoyl)-phenoxy]-2-methylpropanoic acid and isopropyl 2-(4-chlorophenoxy)-2-methylpropanoate, also known as fenofibrate and isopropyl clofibrate, are hypolipidemic agents of the fibrate family. In a previously reported triclinic structure of fenofibrate (polymorph I) the methyl groups of the isopropyl moiety (iPr) are located symmetrically about the carboxylate group. We report a new monoclinic form (polymorph II) of fenofibrate and a first structural description of isopropyl clofibrate, and in these the methyl groups are placed asymmetrically about the carboxylate group. In particular the dihedral (torsion) angle between the hydrogen atom on the secondary C and the C atom of the carboxyl group makes a 2.74° angle about the ester O-C bond in the symmetric fenofibrate structure of polymorph I, whereas the same dihedral angle is 45.94° in polymorph II and -30.9° in the crystal structure of isopropyl clofibrate. Gas phase DFT geometry minimizations of fenofibrate and isopropyl clofibrate result in lowest energy conformations for both molecules with a value of about ± 30° for this same angle between the O=C-O-C plane and the C-H bond of the iPr group. A survey of crystal structures containing an iPr ester group reveals that the asymmetric conformation is predominant. Although the hydrogen atom on the secondary C atom of the isopropyl group is located at a comparable distance from the carbonyl oxygen in the symmetric and asymmetric fenofibrate (2.52 and 2.28 Å) and the isopropyl clofibrate (2.36 Å) structures, this hydrogen atom participates in a puckered five membered ring arrangement in the latter two that is unlike the planar arrangement found in symmetric fenofibrate (polymorph I). Polar molecular surface area (PSA) values indicate fenofibrate and isopropyl clofibrate are less able to act as acceptors of hydrogen bonds than their corresponding acid derivatives. Surface area calculations show dynamic polar molecular surface area (PSAd

Mass Spectrometry of Intact Proteins Reveals +98 u Chemical Artifacts Following Precipitation in Acetone.

Science.gov (United States)

Güray, Melda Z; Zheng, Shi; Doucette, Alan A

2017-02-03

Protein precipitation in acetone is frequently employed ahead of mass spectrometry for sample preconcentration and purification. Unfortunately, acetone is not chemically inert; mass artifacts have previously been observed on glycine-containing peptides when exposed to acetone under acidic conditions. We herein report a distinct chemical modification occurring at the level of intact proteins when incubated in acetone. This artifact manifests as one or more satellite peaks in the MS spectrum of intact protein, spaced 98 u above the mass of the unmodified protein. Other artifacts (+84, +112 u) also appear upon incubation of proteins or peptides in acetone. The reaction is pH-sensitive, being suppressed when proteins are exposed to acetone under acidic conditions. The +98 u artifact is speculated to originate through an intermediate product of aldol condensation of acetone to form diacetone alcohol and mesityl oxide. A +98 u product could originate from nucleophilic attack on mesityl oxide or through condensation with diacetone alcohol. Given the extent of modification possible upon exposure of proteins to acetone, particularly following overnight solvent exposure or incubation at room temperature, an awareness of the variables influencing this novel modification is valued by proteomics researchers who employ acetone precipitation for protein purification.

Profiling and relative quantification of phosphatidylethanolamine based on acetone stable isotope derivatization.

Science.gov (United States)

Wang, Xiang; Wei, Fang; Xu, Ji-Qu; Lv, Xin; Dong, Xu-Yan; Han, Xianlin; Quek, Siew-Young; Huang, Feng-Hong; Chen, Hong

2016-01-01

Phosphatidylethanolamine (PE) is considered to be one of the pivotal lipids for normal cellular function as well as disease initiation and progression. In this study, a simple, efficient, reliable, and inexpensive method for the qualitative analysis and relative quantification of PE, based on acetone stable isotope derivatization combined with double neutral loss scan-shotgun electrospray ionization tandem-quadrupole mass spectrometry analysis (ASID-DNLS-Shotgun ESI-MS/MS), was developed. The ASID method led to alkylation of the primary amino groups of PE with an isopropyl moiety. The use of acetone (d0-acetone) and deuterium-labeled acetone (d6-acetone) introduced a 6 Da mass shift that was ideally suited for relative quantitative analysis, and enhanced sensitivity for mass analysis. The DNLS model was introduced to simultaneously analyze the differential derivatized PEs by shotgun ESI-MS/MS with high selectivity and accuracy. The reaction specificity, labeling efficiency, and linearity of the ASID method were thoroughly evaluated in this study. Its excellent applicability was validated by qualitative and relative quantitative analysis of PE species presented in liver samples from rats fed different diets. Using the ASID-DNLS-Shotgun ESI-MS/MS method, 45 PE species from rat livers have been identified and quantified in an efficient manner. The level of total PEs tended to decrease in the livers of rats on high fat diets compared with controls. The levels of PE 32:1, 34:3, 34:2, 36:3, 36:2, 42:10, plasmalogen PE 36:1 and lyso PE 22:6 were significantly reduced, while levels of PE 36:1 and lyso PE 16:0 increased. Copyright © 2015 Elsevier B.V. All rights reserved.

Profiling and relative quantification of phosphatidylethanolamine based on acetone stable isotope derivatization

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiang [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China); Wei, Fang, E-mail: willasa@163.com [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China); Xu, Ji-qu; Lv, Xin; Dong, Xu-yan [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China); Han, Xianlin [Center for Metabolic Origins of Disease, Sanford Burnham Prebys Medical Discovery Institute, Orlando, FL 32827 (United States); College of Basic Medical Sciences, Zhejiang Chinese Medical University, 548 Bingwen Road, Hangzhou, Zhejiang 310053 (China); Quek, Siew-young [School of Chemical Science, The University of Auckland, Auckland 1142 (New Zealand); Huang, Feng-hong [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China); Chen, Hong, E-mail: chenhong@oilcrops.cn [Oil Crops Research Institute of the Chinese Academy of Agricultural Sciences, Key Laboratory of Biology and Genetic Improvement of Oil Crops, Ministry of Agriculture (China); Hubei Key Laboratory of Lipid Chemistry and Nutrition (China)

2016-01-01

Phosphatidylethanolamine (PE) is considered to be one of the pivotal lipids for normal cellular function as well as disease initiation and progression. In this study, a simple, efficient, reliable, and inexpensive method for the qualitative analysis and relative quantification of PE, based on acetone stable isotope derivatization combined with double neutral loss scan-shotgun electrospray ionization tandem-quadrupole mass spectrometry analysis (ASID-DNLS-Shotgun ESI-MS/MS), was developed. The ASID method led to alkylation of the primary amino groups of PE with an isopropyl moiety. The use of acetone (d{sub 0}-acetone) and deuterium-labeled acetone (d{sub 6}-acetone) introduced a 6 Da mass shift that was ideally suited for relative quantitative analysis, and enhanced sensitivity for mass analysis. The DNLS model was introduced to simultaneously analyze the differential derivatized PEs by shotgun ESI-MS/MS with high selectivity and accuracy. The reaction specificity, labeling efficiency, and linearity of the ASID method were thoroughly evaluated in this study. Its excellent applicability was validated by qualitative and relative quantitative analysis of PE species presented in liver samples from rats fed different diets. Using the ASID-DNLS-Shotgun ESI-MS/MS method, 45 PE species from rat livers have been identified and quantified in an efficient manner. The level of total PEs tended to decrease in the livers of rats on high fat diets compared with controls. The levels of PE 32:1, 34:3, 34:2, 36:3, 36:2, 42:10, plasmalogen PE 36:1 and lyso PE 22:6 were significantly reduced, while levels of PE 36:1 and lyso PE 16:0 increased. - Highlights: • A novel isotope reagent acetone was explored for the derivatization of PEs. • The labeling reaction was carried out under mild conditions with high specificity. • Enhanced detection sensitivity of PEs was achieved after derivatization. • The ASID-DNLS-Shotgun MS/MS method was used to relative quantification of PEs.

Processing of beet-sugar molasses in the acetone-butyl alcohol industry

Energy Technology Data Exchange (ETDEWEB)

Zalesskaya, M I; Logotkin, I S; Marfina, A M; Gus' kova, N P; Chekasina, E V

1958-01-01

Possibility of partial replacement of flour by beet-sugar molasses (I) in acetone-BuOH fermentation was investigated on a commercial scale. Detailed regimes of experiments carried out in two trials were given. Yields of fermentation (kg/1000 kg starch of mash) were: 125.3, 214.4, and 31.5 of acetone, BuOH and EtOH, respectively, for pure flour-mash; 123.3, 215.3, and 28.7 of acetone, BuOH, and EtOH, respectively, at 10% flour replaced by I; 127.8, 205.9, and 51.8, respectively, at 50% flour replaced by I; and 120.17, 216.48, and 42.3, respectively, at 62% flour replaced by I. Inoculum, grown in the seed-mash containing flour only, was not mixed with fermentor-mash until the stage of acid production by the inoculum was reached. During the fermentation of mashes in which 62% flour was replaced by I, a slight foaming was observed.

Green synthesis of isopropyl myristate in novel single phase medium Part II: Packed bed reactor (PBR) studies.

Science.gov (United States)

Vadgama, Rajeshkumar N; Odaneth, Annamma A; Lali, Arvind M

2015-12-01

Isopropyl myristate is a useful functional molecule responding to the requirements of numerous fields of application in cosmetic, pharmaceutical and food industry. In the present work, lipase-catalyzed production of isopropyl myristate by esterification of myristic acid with isopropyl alcohol (molar ratio of 1:15) in the homogenous reaction medium was performed on a bench-scale packed bed reactors, in order to obtain suitable reaction performance data for upscaling. An immobilized lipase B from Candida antartica was used as the biocatalyst based on our previous study. The process intensification resulted in a clean and green synthesis process comprising a series of packed bed reactors of immobilized enzyme and water dehydrant. In addition, use of the single phase reaction system facilitates efficient recovery of the product with no effluent generated and recyclability of unreacted substrates. The single phase reaction system coupled with a continuous operating bioreactor ensures a stable operational life for the enzyme.

Green synthesis of isopropyl myristate in novel single phase medium Part II: Packed bed reactor (PBR studies

Directory of Open Access Journals (Sweden)

Rajeshkumar N. Vadgama

2015-12-01

Full Text Available Isopropyl myristate is a useful functional molecule responding to the requirements of numerous fields of application in cosmetic, pharmaceutical and food industry. In the present work, lipase-catalyzed production of isopropyl myristate by esterification of myristic acid with isopropyl alcohol (molar ratio of 1:15 in the homogenous reaction medium was performed on a bench-scale packed bed reactors, in order to obtain suitable reaction performance data for upscaling. An immobilized lipase B from Candida antartica was used as the biocatalyst based on our previous study. The process intensification resulted in a clean and green synthesis process comprising a series of packed bed reactors of immobilized enzyme and water dehydrant. In addition, use of the single phase reaction system facilitates efficient recovery of the product with no effluent generated and recyclability of unreacted substrates. The single phase reaction system coupled with a continuous operating bioreactor ensures a stable operational life for the enzyme.

Fate of acetone in an outdoor model stream in southern Mississippi, U.S.A.

Science.gov (United States)

Rathbun, R.E.; Stephens, D.W.; Shultz, D.J.; Tai, D.Y.

1988-01-01

The fate of acetone in water was investigated in an outdoor model stream located in southern Mississippi, U.S.A. Acetone was injected continuously for 32 days resulting in small milligram-perliter concentrations in the stream. Rhodamine-WT dye was injected at the beginning and at the end of the study to determine the time-of-travel and dispersion characteristics of the stream. A 12-h injection of t-butyl alcohol (TBA) was used to determine the volatilization characteristics of the stream. Volatilization controlled the acetone concentration in the stream. Significant bacterial degradation of acetone did not occur, contrary to expectations based on previous laboratory studies. Attempts to induce degradation of the acetone by injecting glucose and a nutrient solution containing bacteria acclimated to acetone were unsuccessful. Possible explanations for the lack of bacterial degradation included a nitrate limitation and a limited residence time in the stream system. ?? 1988.

Breath acetone as a potential marker in clinical practice.

Science.gov (United States)

Ruzsányi, Veronika; Péter Kalapos, Miklós

2017-06-01

In recent decades, two facts have changed the opinion of researchers about the function of acetone in humans. Firstly, it has turned out that acetone cannot be regarded as simply a waste product of metabolism, because there are several pathways in which acetone is produced or broken down. Secondly, methods have emerged making possible its detection in exhaled breath, thereby offering an attractive alternative to investigation of blood and urine samples. From a clinical point of view the measurement of breath acetone levels is important, but there are limitations to its wide application. These limitations can be divided into two classes, technical and biological limits. The technical limits include the storage of samples, detection threshold, standardization of clinical settings, and the price of instruments. When considering the biological ranges of acetone, personal factors such as race, age, gender, weight, food consumption, medication, illicit drugs, and even profession/class have to be taken into account to use concentration information for disorders. In some diseases such as diabetes mellitus and lung cancer, as well as in nutrition-related behavior such as starvation and ketogenic diet, breath acetone has been extensively examined. At the same time, there is a lack of investigations in other cases in which ketosis is also evident, such as in alcoholism or an inborn error of metabolism. In summary, the detection of acetone in exhaled breath is a useful and promising tool for diagnosis and it can be used as a marker to follow the effectiveness of treatments in some disorders. However, further endeavors are needed for clarification of the exact distribution of acetone in different body compartments and evaluation of its complex role in humans, especially in those cases in which a ketotic state also occurs.

Toluene metabolism in isolated rat hepatocytes: effects of in vivo pretreatment with acetone and phenobarbital

Energy Technology Data Exchange (ETDEWEB)

Smith-Kielland, A.; Ripel, A. (National Inst. of Forensic Toxicology, Oslo (Norway))

1993-02-01

Hepatocytes isolated from control, acetone- and phenobarbital-pretreated rats were used to study the metabolic conversion of toluene to benzyl alcohol, benzaldehyde, benzoic acid and hippuric acid at low (<100 [mu]M) and high (100-500 [mu]M) toluene concentrations. The baseline formation rates of toluene metabolites (benzyl alcohol, benzoic acid and hippuric acid) were 2.9[+-]1.7 and 10.0[+-]2.3 nmol/mg cell protein/60 min at low and high toluene concentrations, respectively. In vivo pretreatment of rats with acetone and phenobarbital increased the formation of metabolites: at low toluene concentrations 3- and 5-fold, respectively; at high toluene concentrations no significant increase (acetone) and 8-fold increase (phenobarbital). Apparent inhibition by ethanol, 7 and 60 mM, was most prominent at low toluene concentrations: 63% and 69%, respectively, in control cells; 84% and 91% in acetone-pretreated cells, and 32% (not significant) and 51% in phenobarbital-pretreated cells. Ethanol also caused accumulation of benzyl alcohol. The apparent inhibition by isoniazid was similar to that of ethanol at low toluene concentrations. Control and acetone-pretreated cells were apparently resistant towards metyrapone; the decrease was 49% and 64% in phenobarbital-pretreated cells at low and high toluene concentrations, respectively. In these cells, the decrease in presence of combined ethanol and metyrapone was 95% (low toluene concentrations). 4-Methylpyrazole decreased metabolite formation extensively in all groups. Benzaldehyde was only found in the presence of an aldehyde dehydrogenase inhibitor. Increased ratio benzoic/hippuric acid was observed at high toluene concentrations. These results demonstrate that toluene oxidation may be studied by product formation in isolated hepatocytes. However, the influence of various enzymes in the overall metabolism could not be ascertained due to lack of inhibitor specificity. (orig.).

Acetone poisoning

Science.gov (United States)

... this page: //medlineplus.gov/ency/article/002480.htm Acetone poisoning To use the sharing features on this page, please enable JavaScript. Acetone is a chemical used in many household products. ...

The Effect of Tin Addition to ZnO Nanosheet Thin Films for Ethanol and Isopropyl Alcohol Sensor Applications

Directory of Open Access Journals (Sweden)

Brian Yuliarto

2015-01-01

Full Text Available The requirements of green environmental and public health monitoring have become stricter along with greater world attention for global warming. The most common pollutants in the environment that need tightened control are volatile organic compounds (VOC. Compared to other kinds of sensors, semiconductor sensors have certain advantages, including high sensitivity, fast response, simplicity, high reliability and low cost. In this work, ZnO and Sn-doped ZnO nanostructure materials with high surface nanosheet areas were synthesized using chemical bath deposition. The X-ray diffraction patterns could be indexed according to crystallinity mainly to a hexagonal wurzite ZnO structure. The scanning electron microscopy (SEM results showed that in all samples, the thin films after the addition of Sn consisted of many kinds of microstructure patterns on a nanoscale, with various sheet shapes. The sensor performance characterizations showed that VOC levels as low as 3 vol% of isopropyl alcohol (IPA and ethanol could be detected at sensitivities of 83.86% and 85.57%, respectively. The highest sensitivity of all sensors was found at an Sn doping of 1.4 at%. This high sensor sensitivity is a result of the high surface area and Sn doping, which in turn produced a higher absorption of the targeted gas.

Co-production of acetone and ethanol with molar ratio control enables production of improved gasoline or jet fuel blends.

Science.gov (United States)

Baer, Zachary C; Bormann, Sebastian; Sreekumar, Sanil; Grippo, Adam; Toste, F Dean; Blanch, Harvey W; Clark, Douglas S

2016-10-01

The fermentation of simple sugars to ethanol has been the most successful biofuel process to displace fossil fuel consumption worldwide thus far. However, the physical properties of ethanol and automotive components limit its application in most cases to 10-15 vol% blends with conventional gasoline. Fermentative co-production of ethanol and acetone coupled with a catalytic alkylation reaction could enable the production of gasoline blendstocks enriched in higher-chain oxygenates. Here we demonstrate a synthetic pathway for the production of acetone through the mevalonate precursor hydroxymethylglutaryl-CoA. Expression of this pathway in various strains of Escherichia coli resulted in the co-production of acetone and ethanol. Metabolic engineering and control of the environmental conditions for microbial growth resulted in controllable acetone and ethanol production with ethanol:acetone molar ratios ranging from 0.7:1 to 10.0:1. Specifically, use of gluconic acid as a substrate increased production of acetone and balanced the redox state of the system, predictively reducing the molar ethanol:acetone ratio. Increases in ethanol production and the molar ethanol:acetone ratio were achieved by co-expression of the aldehyde/alcohol dehydrogenase (AdhE) from E. coli MG1655 and by co-expression of pyruvate decarboxylase (Pdc) and alcohol dehydrogenase (AdhB) from Z. mobilis. Controlling the fermentation aeration rate and pH in a bioreactor raised the acetone titer to 5.1 g L(-1) , similar to that obtained with wild-type Clostridium acetobutylicum. Optimizing the metabolic pathway, the selection of host strain, and the physiological conditions employed for host growth together improved acetone titers over 35-fold (0.14-5.1 g/L). Finally, chemical catalysis was used to upgrade the co-produced ethanol and acetone at both low and high molar ratios to higher-chain oxygenates for gasoline and jet fuel applications. Biotechnol. Bioeng. 2016;113: 2079-2087. © 2016 Wiley

Acetone-butyl alcohol fermentation of the cornstalk hydrolyzates prepared by the method of Riga

Energy Technology Data Exchange (ETDEWEB)

Nakhmanovich, N A; Shcheblykina, N A; Kalnina, V; Pelsis, D

1960-01-01

The possibility of use of waste instead of food products in the acetone-butyl alcohol fermentation was investigated. Crushed cornstalks hydrolyzed by the method of Riga were inverted at varying conditions. The hydrolyzate containing about 50% of reducing substances (RS), based on dry weight of cornstalks, was neutralized to pH 6.3-6.5, diluted with water to the final concentration 5.0-5.1% of RS filtered, and the filtrate sterilized. The resulting liquor (I) was mixed with the wheat meal mash containing 5% of sugar (starch calculated as glucose) and fermented. The utilization of I depended upon the regime of inversion; the optimal being 20 minutes at 115/sup 0/, hydrocoefficient 1:4. In this case the use of 40% of mash sugar in form of I did not impair the yield of fermentation. The use of corn instead of wheat meal decreased the yield of butanol and increased that of ethanol. The fermentation of the mixture of I (final concentration 3% RS) and corn gluten (final concentration 2%), mineral salts added, gave higher yields than did the fermentation of the wheat meal mash.

Baby Shampoo Versus Povidone-Iodine or Isopropyl Alcohol in Reducing Eyelid Skin Bacterial Load.

Science.gov (United States)

Garcia, Giancarlo A; Nguyen, Christine V; Yonkers, Marc A; Tao, Jeremiah P

Baby shampoo is used as an alternative surgical skin preparation, but the evidence supporting its use is scarce with no descriptions of efficacy in the periocular region. The authors compare the efficacy of baby shampoo, povidone-iodine (PI, Betadine) and isopropyl alcohol (IA) in reducing eyelid skin bacterial load. Prospective, randomized, comparative, and interventional trial. Bacterial load on adult, human eyelid skin was quantitated before and after cleansing with 1) dilute baby shampoo, 2) 10% PI, or 3) 70% IA. Paired skin swabs were collected from a 1 cm area of the upper eyelid of subjects before and after a standardized surgical scrub technique. Samples were cultured on 5% sheep blood agar for 24 hours. The number of colony forming units (CFU) was assessed and bacterial load per square centimeter of eyelid skin was quantified. Baseline and postcleansing samples were assessed from 42 eyelids of 42 subjects (n = 14 for each of baby shampoo, PI, and IA). Before cleansing, similar amounts of bacterial flora were grown from all specimens (median log CFU/cm = 2.04 before baby shampoo, 2.01 before PI, 2.11 before IA; p > 0.05). All 3 cleansing agents significantly reduced the bacterial load (p shampoo, 0.39 after PI, 0.59 after IA; p > 0.05). Change from baseline in bacterial load was statistically similar for all 3 agents (median reduction in log CFU/cm = 1.28 with baby shampoo, 1.57 with PI, 1.40 with IA; p > 0.05). These corresponded to bacterial load reductions of 96.3%, 96.6%, and 98.4% for baby shampoo, PI, and IA, respectively. Baby shampoo achieved comparable diminution in eyelid skin bacterial load to PI or IA. These data suggest baby shampoo may be an effective preoperative cleansing agent.

Study of dementia associated with alcoholism using N-isopropyl-p-[123I] iodoamphetamine SPECT and 2 tesla magnetic resonance imaging

International Nuclear Information System (INIS)

Fujimoto, Toshiro; Uchida, Tsunehisa; Yokoyama, Yoji

1988-01-01

Using DSM-III-R criteria, five patients (ages 46 ∼ 76 years) were diagosed as having DAA (dementia associated with alcoholism). An investigation was conducted using a ring-type single proton emission tomography system with N-isopropyl-p-[ 123 I] iodoamphetamine (IMP) and a magnetic resonance imaging system with a superconductive 2 tesla magnet. IMP uptake was measured 25 ∼ 30 minutes after injection. Bilateral IMP uptake reduction was seen in all of the patients. The distribution of the reduced IMP uptake showed in the temporal region of all patients ; the frontal region in four of the patients and the occipital region in two of the patients. The reduction of IMP uptake was irregular, generally mild, and less severe than that of Alzheimer type dementia. The MRI study showed cortical atrophy, especially in the frontal and temporal areas, and also showed enlargement of the lateral and third ventricles. The reduced IMP uptake corresponded to cerebral atrophy and ventricular dilatation on the SE image (TR 3000, TE 60 or 82). These results indicate that the IMP SPECT and MRI studies are useful in examining DAA patients and in the classification of other types of dementia. (author)

An acetone bio-sniffer (gas phase biosensor) enabling assessment of lipid metabolism from exhaled breath.

Science.gov (United States)

Ye, Ming; Chien, Po-Jen; Toma, Koji; Arakawa, Takahiro; Mitsubayashi, Kohji

2015-11-15

Several volatile organic compounds (VOCs) are released from human breath or skin. Like chemical substances in blood or urine, some of these vapors can provide valuable information regarding the state of the human body. A highly sensitive acetone biochemical gas sensor (bio-sniffer) was developed and used to measure exhaled breath acetone concentration, and assess lipid metabolism based on breath acetone analysis. A fiber-optic biochemical gas sensing system was constructed by attaching a flow-cell with nicotinamide adenine dinucleotide (NADH)-dependent secondary alcohol dehydrogenase (S-ADH) immobilized membrane onto a fiber-optic NADH measurement system. The NADH measurement system utilizes an ultraviolet-light emitting diode with peak emission of 335 nm as an excitation light source. NADH is consumed by the enzymatic reaction of S-ADH, and the consumption is proportional to the concentration of acetone vapor. Phosphate buffer which contained NADH was circulated into the flow-cell to rinse products and the excessive substrates from the optode. The change of fluorescent emitted from NADH is analyzed by the PMT. Hence, fluorescence intensity decreased as the acetone concentration increased. The relationship between fluorescence intensity and acetone concentration was identified from 20 ppb to 5300 ppb. This interval included the concentration of acetone vapor in the breath of healthy people and those suffering from disorders of carbohydrate metabolism. Finally, the acetone bio-sniffer was used to measure breath acetone during an exercise stress test on an ergometer after a period of fasting. The concentration of acetone in breath was shown to significantly increase after exercise. This biosensor allows rapid, highly sensitive and selective measurement of lipid metabolism. Copyright © 2015 Elsevier B.V. All rights reserved.

Study of dementia associated with alcoholism using N-isopropyl-p-(/sup 123/I) iodoamphetamine SPECT and 2 tesla magnetic resonance imaging

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, Toshiro; Uchida, Tsunehisa; Yokoyama, Yoji and others

1988-08-01

Using DSM-III-R criteria, five patients (ages 46 approx. 76 years) were diagosed as having DAA (dementia associated with alcoholism). An investigation was conducted using a ring-type single proton emission tomography system with N-isopropyl-p-(/sup 123/I) iodoamphetamine (IMP) and a magnetic resonance imaging system with a superconductive 2 tesla magnet. IMP uptake was measured 25 approx. 30 minutes after injection. Bilateral IMP uptake reduction was seen in all of the patients. The distribution of the reduced IMP uptake showed in the temporal region of all patients ; the frontal region in four of the patients and the occipital region in two of the patients. The reduction of IMP uptake was irregular, generally mild, and less severe than that of Alzheimer type dementia. The MRI study showed cortical atrophy, especially in the frontal and temporal areas, and also showed enlargement of the lateral and third ventricles. The reduced IMP uptake corresponded to cerebral atrophy and ventricular dilatation on the SE image (TR 3000, TE 60 or 82). These results indicate that the IMP SPECT and MRI studies are useful in examining DAA patients and in the classification of other types of dementia.

Production of acetone and conversion of acetone to acetate in the perfused rat liver

International Nuclear Information System (INIS)

Gavino, V.C.; Somma, J.; Philbert, L.; David, F.; Garneau, M.; Belair, J.; Brunengraber, H.

1987-01-01

The utilization of millimolar concentrations of [2- 14 C]acetone and the production of acetone from acetoacetate were studied in perfused livers from 48-h starved rats. We devised a procedure for determining, in a perfused liver system, the first-order rate constant for the decarboxylation of acetoacetate (0.29 +/- 0.09 h-1, S.E., n = 8). After perfusion of livers with [2- 14 C]acetone, labeled acetate was isolated from the perfusion medium and characterized as [1- 14 C]acetate. No radioactivity was found in lactate or 3-hydroxybutyrate. After 90 min of perfusion with [2- 14 C]acetone, the specific activity of acetate was 30 +/- 4% (n = 13) of the initial specific activity of acetone. We conclude that, in perfused livers from 2-day starved rats, acetone metabolism occurs for the most part via free acetate

Pulse radiolytic one-electron reduction of 2-hydroxy- and 2,6-dihydroxy-9,10-anthraquinones

International Nuclear Information System (INIS)

Pal, Haridas; Mukherjee, Tulsi; Mittal, J.P.

1994-01-01

The semiquinone free radicals produced by one-electron reduction of 2-hydroxy-9-10-anthraquinone (2HAQ) and 2,6-dihydroxy-9,10-anthraquinone (26DHAQ) in aqueous formate solution, water-isopropyl alcohol-acetone mixed solvent and isopropyl alcohol have been studied using the pulse radiolysis technique. The absorption characteristics, kinetic parameters of formation and decay, acid-base behaviour and redox characteristics of the semiquinones have been investigated and compared with the corresponding characteristics of a few intramolecularly hydro-bonded anthrasemiquinone derivatives. The non-hydrogen-bonded semiquinones show two pKsub(a) values (4.7 and 10.7 for 2HAQ and 5.4 and 8.7 for 26DHAQ, respectively) within the pH range 1-14, whereas other intramolecularly hydrogen-bonded semiquinones show only one pKsub(a). The one-electron reduction potential (E' 7 ) values for 2HAQ (-440 mV) and 26DHAQ (- 400 mV) are more negative than those of the intramolecularly hydrogen-bonded systems. (Author)

Synthesis of complex compounds in the system [ReOG5]2--thiosemicarbazone acetone-Hg-acetone

International Nuclear Information System (INIS)

Amindzhanov, A.A.; Kurbanov, N.M.

1993-01-01

Present article is devoted to synthesis of complex compounds in the system [ReOG 5 ] 2- -thiosemicarbazone acetone-Hg-acetone. The literature data on complex compounds of various metals with thiosemicarbazone was summarized. The synthesis of complex compounds in the system [ReOG 5 ] 2- -thiosemicarbazone acetone-Hg-acetone was conducted. The complex compounds of rhenium with methyl ident thiosemicarbazone were synthesized.

Coumarins as turn on/off fluorescent probes for detection of residual acetone in cosmetics following headspace single-drop microextraction.

Science.gov (United States)

Cabaleiro, N; de la Calle, I; Bendicho, C; Lavilla, I

2014-11-01

In this work, a new method based on headspace-single drop microextraction for the determination of residual acetone in cosmetics by microfluorospectrometry is proposed. Acetone causes fluorescence changes in a 2.5 µL-ethanolic drop (40% v/v) containing 3.10(-4) mol L(-1) 7-hydroxy-4-methylcoumarin ('turn off') or 6.10(-6) mol L(-1) 7-diethylamino-4-methylcoumarin ('turn on'). Polarity and ability to form hydrogen bonds of short chain alcohols (polar protic solvents) were crucial in order to observe these changes in the presence of acetone (polar aprotic solvent). Parameters related with the HS-SDME procedure were studied, namely headspace volume, composition, volume and temperature of drop, microextraction time, stirring rate, mass and temperature of sample, as well as the effect of potential interferents (alcohols and fragrances). The high volatility of acetone allows its extraction from an untreated cosmetic sample within 3 min. A detection limit of 0.26 µg g(-1) and repeatability, expressed as relative standard deviation, around 5% were reached. Accuracy of the proposed methodology was evaluated by means of recovery studies. The method was successfully used to analyze different cosmetics. Simplicity and high sample throughput can be highlighted. Copyright © 2014 Elsevier B.V. All rights reserved.

Deracemization of Secondary Alcohols by using a Single Alcohol Dehydrogenase

KAUST Repository

Karume, Ibrahim

2016-03-01

© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. We developed a single-enzyme-mediated two-step approach for deracemization of secondary alcohols. A single mutant of Thermoanaerobacter ethanolicus secondary alcohol dehydrogenase enables the nonstereoselective oxidation of racemic alcohols to ketones, followed by a stereoselective reduction process. Varying the amounts of acetone and 2-propanol cosubstrates controls the stereoselectivities of the consecutive oxidation and reduction reactions, respectively. We used one enzyme to accomplish the deracemization of secondary alcohols with up to >99% ee and >99.5% recovery in one pot and without the need to isolate the prochiral ketone intermediate.

Effects of low-molecular weight alcohols on bacterial viability

Directory of Open Access Journals (Sweden)

Man Adrian

2017-10-01

Full Text Available Alcohol based solutions are among the most convenient and wide spread aid in the prevention of nosocomial infections. The current study followed the efficacy of several types and isomers of alcohols on different bacterial species. Seven alcohols (ethyl, n-propyl, iso-propyl, n-butyl, iso-butyl, tert-butyl alcohol, and ethylene glycol were used to evaluate their minimal inhibitory and bactericidal effects by microdilution method on bacteria that express many phenotypical characteristics: different cell-wall structure (Gram positive/negative bacteria, capsule production (Klebsiella pneumoniae, antibiotic resistance (MRSA vs MSSA or high environmental adaptability (Pseudomonas aeruginosa. Results: The best inhibitory effect was noticed for n-propyl, followed by iso-propyl, n-butyl, and iso-butyl alcohols with equal values. Ethylene glycol was the most inefficient alcohol on all bacteria. In K. pneumoniae and P. aeruginosa, the bactericidal concentrations were higher than the inhibitory one, and to a level similar to that encountered for most of the Gram-positive bacteria. Among Gram-positive cocci, E. faecalis presented the lowest susceptibility to alcohols. Conclusions: All alcohols presented good effect on bacteria, even in low concentrations. Compared to ethanol as standard, there are better alternatives that can be used as antimicrobials, namely longer-chain alcohols such as propyl or butyric alcohols and their iso- isomers. Ethylene glycol should be avoided, due to its toxicity hazard and low antimicrobial efficacy. Bacterial phenotype (highly adaptable bacteria, biofilm formation and structure (cell wall structure, presence of capsule may drastically affect the responsiveness to the antimicrobial activity of alcohols, leading to higher bactericidal than inhibitory concentrations.

An acetone breath analyzer using cavity ringdown spectroscopy: an initial test with human subjects under various situations

International Nuclear Information System (INIS)

Wang, Chuji; Surampudi, Anand B

2008-01-01

We have developed a portable breath acetone analyzer using cavity ringdown spectroscopy (CRDS). The instrument was initially tested by measuring the absorbance of breath gases at a single wavelength (266 nm) from 32 human subjects under various conditions. A background subtraction method, implemented to obtain absorbance differences, from which an upper limit of breath acetone concentration was obtained, is described. The upper limits of breath acetone concentration in the four Type 1 diabetes (T1D) subjects, tested after a 14 h overnight fast, range from 0.80 to 3.97 parts per million by volume (ppmv), higher than the mean acetone concentration (0.49 ppmv) in non-diabetic healthy breath reported in the literature. The preliminary results show that the instrument can tell distinctive differences between the breath from individuals who are healthy and those with T1D. On-line monitoring of breath gases in healthy people post-exercise, post-meals and post-alcohol-consumption was also conducted. This exploratory study demonstrates the first CRDS-based acetone breath analyzer and its potential application for point-of-care, non-invasive, diabetic monitoring

Kinetic Model of Resin－Catalyzed Decomposition of Acetone Cyanohydrin in Organic Solvent

Institute of Scientific and Technical Information of China (English)

章亭洲; 杨立荣; 朱自强; 吴坚平

2003-01-01

Decomposition of acetone cyanohydrin is the first-step reaction for preparing (S)-α-cyano-3-phenoxybenzyl alcohol (CPBA) by the one-pot method in organic media. Considering the compatibility of biocatalysts with chemical catalysts and the successive operation in the bioreactor, anion exchange resin (D301) was used as catalyst for this reaction. External diffusion limitation was excluded by raising rotational speed to higher than 190r·min-1 in both solvents. Internal diffusion limitation was verified to be insignificant in this reaction system. The effect of acetone cyanohydrin concentration on the reaction was also investigated. An intrinsic kinetic model was proposed when the mass transfer limitation was excluded, and the average deviation of the model is 10.5%.

Acetone production by methylobacteria.

Science.gov (United States)

Thomson, A W; O'Neill, J G; Wilkinson, J F

1976-09-01

An accumulation of acetone was observed during the metabolism of ethane and products of ethane oxidation by washed suspensions of Methylosinus trichosporium OB3B. This strain possessed an acetoacetate decarboxylase and 3-hydroxybutyrate dehydrogenase, and a decline in poly-beta-hydroxybutyric acid occurred under the same conditions as acetone formation. A pathway of acetone production from poly-beta-hydroxybutyric acid via 3-hydroxybutyrate and acetoacetate was suggested.

First Electrochemical Method of Nitrothal-Isopropyl Determination in Water Samples

Directory of Open Access Journals (Sweden)

Dariusz Guziejewski

2016-01-01

Full Text Available The aim of the research was the use of square wave adsorptive stripping voltammetry (SWAdSV in conjunction with a hanging mercury drop electrode (HMDE for the determination of nitrothal-isopropyl. It was found that optimal SW technique parameters were frequency, 200 Hz; amplitude, 50 mV; and step potential, 5 mV. Accumulation time and potential were studied to select the optimal conditions in adsorptive stripping voltammetry: 45 s at 0.0 V, respectively. The calibration curve (SWSV was linear in the nitrothal-isopropyl concentration range from 2.0 × 10−7 to 2.0 × 10−6 mol L−1 with detection limit of 3.46 × 10−8 mol L−1. The repeatability of the method was determined at a nitrothal-isopropyl concentration level equal to 6.0 × 10−7 mol L−1 and expressed as RSD = 5.5% (n=6. The proposed method was successfully validated by studying the recovery of nitrothal-isopropyl in spiked environmental samples.

Synthesis of 2-Isopropyl Naphthalene Catalyzed by Et3NHCl-AlCl3 Ionic Liquids

Institute of Scientific and Technical Information of China (English)

Li Chenmin; Qi Xin; Tang Xiangyang

2014-01-01

In this paper, 2-isopropyl naphthalene has been synthesized by the reaction of naphthalene and isopropyl bromide, using triethylamine hydrochloride-aluminum chloride ionic liquid as the catalyst. The effect of the catalyst composition, the reaction time, the reaction temperature, the ionic liquid dosage, as well as the molar ratio of the reagents on the 2-isopropyl naphthalene yield was systematically investigated. The optimal reaction conditions cover:an AlCl3 to Et3NHCl ratio of 2.0, a reaction time of 3 h, a reaction temperature of 15.0℃, a volume fraction of ionic liquid to the mixture (isopropyl bromide, n-dodecane and n-hexane) of 9%, and a naphthalene/isopropyl bromide molar ratio of 4.0. Under the optimal reaction condi-tions, the conversion of isopropyl bromide reached 98%and the selectivity of 2-isopropyl naphthalene was equal to 80%. The test results veriifed good catalytic activity upon using Et3NHCl-AlCl3 ionic liquid as the catalyst for alkylation of naph-thalene with isopropyl bromide. The activity of the ionic liquid remains unchanged after it has been recycled for 4 times.

Determination of residual acetone and acetone related impurities in drug product intermediates prepared as Spray Dried Dispersions (SDD) using gas chromatography with headspace autosampling (GCHS).

Science.gov (United States)

Quirk, Emma; Doggett, Adrian; Bretnall, Alison

2014-08-05

Spray Dried Dispersions (SDD) are uniform mixtures of a specific ratio of amorphous active pharmaceutical ingredient (API) and polymer prepared via a spray drying process. Volatile solvents are employed during spray drying to facilitate the formation of the SDD material. Following manufacture, analytical methodology is required to determine residual levels of the spray drying solvent and its associated impurities. Due to the high level of polymer in the SDD samples, direct liquid injection with Gas Chromatography (GC) is not a viable option for analysis. This work describes the development and validation of an analytical approach to determine residual levels of acetone and acetone related impurities, mesityl oxide (MO) and diacetone alcohol (DAA), in drug product intermediates prepared as SDDs using GC with headspace (HS) autosampling. The method development for these analytes presented a number of analytical challenges which had to be overcome before the levels of the volatiles of interest could be accurately quantified. GCHS could be used after two critical factors were implemented; (1) calculation and application of conversion factors to 'correct' for the reactions occurring between acetone, MO and DAA during generation of the headspace volume for analysis, and the addition of an equivalent amount of polymer into all reference solutions used for quantitation to ensure comparability between the headspace volumes generated for both samples and external standards. This work describes the method development and optimisation of the standard preparation, the headspace autosampler operating parameters and the chromatographic conditions, together with a summary of the validation of the methodology. The approach has been demonstrated to be robust and suitable to accurately determine levels of acetone, MO and DAA in SDD materials over the linear concentration range 0.008-0.4μL/mL, with minimum quantitation limits of 20ppm for acetone and MO, and 80ppm for DAA. Copyright

Is breath acetone a biomarker of diabetes? A historical review on breath acetone measurements.

Science.gov (United States)

Wang, Zhennan; Wang, Chuji

2013-09-01

Since the ancient discovery of the 'sweet odor' in human breath gas, pursuits of the breath analysis-based disease diagnostics have never stopped. Actually, the 'smell' of the breath, as one of three key disease diagnostic techniques, has been used in Eastern-Medicine for more than three thousand years. With advancement of measuring technologies in sensitivity and selectivity, more specific breath gas species have been identified and established as a biomarker of a particular disease. Acetone is one of the breath gases and its concentration in exhaled breath can now be determined with high accuracy using various techniques and methods. With the worldwide prevalence of diabetes that is typically diagnosed through blood testing, human desire to achieve non-blood based diabetic diagnostics and monitoring has never been quenched. Questions, such as is breath acetone a biomarker of diabetes and how is the breath acetone related to the blood glucose (BG) level (the golden criterion currently used in clinic for diabetes diagnostic, monitoring, and management), remain to be answered. A majority of current research efforts in breath acetone measurements and its technology developments focus on addressing the first question. The effort to tackle the second question has begun recently. The earliest breath acetone measurement in clearly defined diabetic patients was reported more than 60 years ago. For more than a half-century, as reviewed in this paper, there have been more than 41 independent studies of breath acetone using various techniques and methods, and more than 3211 human subjects, including 1581 healthy people, 242 Type 1 diabetic patients, 384 Type 2 diabetic patients, 174 unspecified diabetic patients, and 830 non-diabetic patients or healthy subjects who are under various physiological conditions, have been used in the studies. The results of the breath acetone measurements collected in this review support that many conditions might cause changes to breath

21 CFR 172.802 - Acetone peroxides.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acetone peroxides. 172.802 Section 172.802 Food and... Multipurpose Additives § 172.802 Acetone peroxides. The food additive acetone peroxides may be safely used in... acetone peroxide, with minor proportions of higher polymers, manufactured by reaction of hydrogen peroxide...

Recycling of acetone by distillation

International Nuclear Information System (INIS)

Brennan, D.L.; Campbell, B.A.; Phelan, J.E.; Harper, M.

1992-09-01

The Resource Conservation Recovery Act (RCRA) identifies spent acetone solvent as a listed hazardous waste. At Fernald, acetone has been spent that has been contaminated with radionuclides and therefore is identified as a mixed hazardous waste. At the time of this publication there is no available approved method of recycling or disposal of radioactively contaminated spent acetone solvent. The Consent Decree with the Ohio EPA and the Consent Agreement with the United States EPA was agreed upon for the long-term compliant storage of hazardous waste materials. The purpose of this project was to demonstrate the feasibility for safely decontaminating spent acetone to background levels of radioactivity for reuse. It was postulated that through heat distillation, radionuclides could be isolated from the spent acetone

Catalytic activity of laminated compounds of graphite with transitions metals in decomposition of alcohols and formic acid

International Nuclear Information System (INIS)

Novikov, Yu.N.; Lapkina, N.D.; Vol'pin, M.E.

1976-01-01

The catalytic activity is studied of laminated graphite compounds with Fe, Co, Ni, Cu, Mo, W and Mn both in the reduced and oxidized forms in gas phase decomposition reactions of isopropyl, n-butyl, cyclohexyl, and 4-tret-butylcyclohexyl alcohols, and also formic acid. All the catalysts are shown to be active in the reactions where isopropyl and n-butyl alcohols undergo decomposition. The laminated compounds of graphite with Co and Ni both in the oxidized and reduction form are the most active catalysts of the selective decomposition of alcohols to aldehydes and ketones, and also formic acid to CO 2 and H 2 . The kinetics of a number of reactions is found to obey the second order equation with allowance made for the system volume

Effect of acetone accumulation on structure and dynamics of lipid membranes studied by molecular dynamics simulations.

Science.gov (United States)

Posokhov, Yevgen O; Kyrychenko, Alexander

2013-10-01

The modulation of the properties and function of cell membranes by small volatile substances is important for many biomedical applications. Despite available experimental results, molecular mechanisms of action of inhalants and organic solvents, such as acetone, on lipid membranes remain not well understood. To gain a better understanding of how acetone interacts with membranes, we have performed a series of molecular dynamics (MD) simulations of a POPC bilayer in aqueous solution in the presence of acetone, whose concentration was varied from 2.8 to 11.2 mol%. The MD simulations of passive distribution of acetone between a bulk water phase and a lipid bilayer show that acetone favors partitioning into the water-free region of the bilayer, located near the carbonyl groups of the phospholipids and at the beginning of the hydrocarbon core of the lipid membrane. Using MD umbrella sampling, we found that the permeability barrier of ~0.5 kcal/mol exists for acetone partitioning into the membrane. In addition, a Gibbs free energy profile of the acetone penetration across a bilayer demonstrates a favorable potential energy well of -3.6 kcal/mol, located at 15-16Å from the bilayer center. The analysis of the structural and dynamics properties of the model membrane revealed that the POPC bilayer can tolerate the presence of acetone in the concentration range of 2.8-5.6 mol%. The accumulation of the higher acetone concentration of 11.2 mol% results, however, in drastic disordering of phospholipid packing and the increase in the membrane fluidity. The acetone molecules push the lipid heads apart and, hence, act as spacers in the headgroup region. This effect leads to the increase in the average headgroup area per molecule. In addition, the acyl tail region of the membrane also becomes less dense. We suggest, therefore, that the molecular mechanism of acetone action on the phospholipid bilayer has many common features with the effects of short chain alcohols, DMSO, and

Fate of acetone in an outdoor model stream with a nitrate supplement, southern Mississippi, U.S.A.

Science.gov (United States)

Rathbun, R.E.; Stephens, D.W.; Tai, D.Y.

1991-01-01

The fate of acetone in an outdoor model stream to which nitrate was added as a nutrient supplement was determined. The stream, in southern Mississippi, U.S.A. was 234 m long. Water was supplied to the stream by an artesian well at about 1.21 s-1, resulting in a mean water velocity of about 0.5 m min-1. Acetone was injected continuously for 26 days resulting in concentrations of 20-40 mg l-1. A nitrate solution was injected for 21 days resulting in an instream concentration of about 1.7 mg l-1 at the upstream end of the stream. Rhodamine-WT dye was used to determine the travel time and dispersion characteristics of the stream, and t-butyl alcohol was used to determine the volatilization characteristics. Volatilization controlled the fate of acetone in the model stream. The lack of substantial bacterial degradation of acetone was contrary to expectations based on the results of laboratory degradation studies using model stream water enriched with nitrate. A possible explanation for the lack of significant degradation in the model stream may be the limited 6-h residence time of the acetone in the stream. ?? 1991.

Analysis of plastic residues in maple sap and syrup collected from tubing systems sanitized with isopropyl alcohol

Directory of Open Access Journals (Sweden)

Luc Lagacé

2017-05-01

Full Text Available A plastic tubing system operated under vacuum is usually used to collect sap from maple trees during spring time to produce maple syrup. This system is commonly sanitized with isopropyl alcohol (IPA to remove microbial contamination colonizing the system during the sugar season. Questions have been raised whether IPA would contribute to the leaching of plastic residues in maple sap and syrup coming from sanitized systems. First, an extraction experiment was performed in the lab on commercial plastic tubing materials that were submitted to IPA under harsh conditions. The results of the GC-MS analysis revealed the presence of many compounds that served has target for further tests. Secondly, tests were done on early and mid-season maple sap and syrup coming from many sugarbushes using IPA or not to determine potential concentrations of plastic residues. Results obtained from sap and syrup samples showed that no quantifiable (< 1–75 μg/L concentration of any plastic molecules tested was determined in all samples coming from IPA treated or not treated systems. However, some samples of first sap run used as a rinse solution to be discarded before the season start and that were coming from non sanitized or IPA sanitized systems, showed quantifiable concentrations of chemical residue such as ultraviolet protector (octabenzone. These results show that IPA can be safely used to sanitize maple sap collection system in regards to the leaching of plastic residues in maple sap and syrup and reinforced the need to thoroughly rinse the tubing system at the beginning of the season for both sanitized and non sanitized systems. Keywords: Food science, Food safety, Materials chemistry

21 CFR 173.210 - Acetone.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acetone. 173.210 Section 173.210 Food and Drugs..., Lubricants, Release Agents and Related Substances § 173.210 Acetone. A tolerance of 30 parts per million is established for acetone in spice oleoresins when present therein as a residue from the extraction of spice. ...

Viscosities and refractive indices of binary systems acetone+1-propanol, acetone+1,2-propanediol and acetone+1,3-propanediol

Directory of Open Access Journals (Sweden)

Živković Emila M.

2014-01-01

Full Text Available Viscosities and refractive indices of three binary systems, acetone+1-propanol, acetone+1,2-propanediol and acetone+1,3-propanediol, were measured at eight temperatures (288.15, 293.15, 298.15, 303.15, 308.15, 313.15, 318.15, 323.15K and at atmospheric pressure. From these data viscosity deviations and deviations in refractive index were calculated and fitted to the Redlich-Kister equation. The viscosity modelling was done by two types of models: predictive UNIFAC-VISCO and ASOG VISCO and correlative Teja-Rice and McAlister equations. The refractive indices of binary mixtures were predicted by various mixing rules and compared with experimental data. [Projekat Ministarstva nauke Republike Srbije, br. 172063

Determination of breath acetone in 149 type 2 diabetic patients using a ringdown breath-acetone analyzer.

Science.gov (United States)

Sun, Meixiu; Chen, Zhuying; Gong, Zhiyong; Zhao, Xiaomeng; Jiang, Chenyu; Yuan, Yuan; Wang, Zhennang; Li, Yingxin; Wang, Chuji

2015-02-01

Over 90% of diabetic patients have Type 2 diabetes. Although an elevated mean breath acetone concentration has been found to exist in Type 1 diabetes (T1D), information on breath acetone in Type 2 diabetes (T2D) has yet to be obtained. In this study, we first used gas chromatography-mass spectrometry (GC-MS) to validate a ringdown breath-acetone analyzer based on the cavity-ringdown-spectroscopy technique, through comparing breath acetone concentrations in the range 0.5-2.5 ppm measured using both methods. The linear fitting of R = 0.99 suggests that the acetone concentrations obtained using both methods are consistent with a largest standard deviation of ±0.4 ppm in the lowest concentration of the range. Next, 620 breath samples from 149 T2D patients and 42 healthy subjects were collected and tested using the breath analyzer. Four breath samples were taken from each subject under each of four different conditions: fasting, 2 h post-breakfast, 2 h post-lunch, and 2 h post-dinner. Simultaneous blood glucose levels were also measured using a standard diabetic-management blood-glucose meter. For the 149 T2D subjects, their exhaled breath acetone concentrations ranged from 0.1 to 19.8 ppm; four different ranges of breath acetone concentration, 0.1-19.8, 0.1-7.1, 0.1-6.3, and 0.1-9.5 ppm, were obtained for the subjects under the four different conditions, respectively. For the 42 healthy subjects, their breath acetone concentration ranged from 0.1 to 2.6 ppm; four different ranges of breath acetone concentration, 0.3-2.6, 0.1-2.6, 0.1-1.7, and 0.3-1.6 ppm, were obtained for the four different conditions. The mean breath acetone concentration of the 149 T2D subjects was determined to be 1.5 ± 1.5 ppm, which was 1.5 times that of 1.0 ± 0.6 ppm for the 42 healthy subjects. No correlation was found between the breath acetone concentration and the blood glucose level of the T2D subjects and the healthy volunteers. This study using a relatively large number of

Radiation-induced heterogeneous polymerization of acrylamide in acetone and acetone--water mixtures

International Nuclear Information System (INIS)

Wada, T.; Sekiya, H.; Machi, S.

1975-01-01

The effects of temperature, dose rate, and monomer concentration on the heterogeneous polymerization of acrylamide in acetone--water mixtures have been studied. Heterogeneous polymerization takes place in mixtures containing less than 60 vol-percent water. The polymerization is steady in acetone and nonsteady in mixtures containing 10 to 50 vol-percent water. The average rate of polymerization is highest in mixtures with about 20 vol-percent water. Polymer molecular weight increases with the increasing water content in the range 0 to 10 vol-percent and does not change in the range of 30 to 70 vol-percent water. For the polymerization in acetone and an acetone-water 60/40 mixture, the activation energies are 2.3 and -1.8 kcal/mole, the dose rate exponents of rate are 0.78 and 0.52, and the monomer concentration exponents of rate are 0.5 and 1.6, respectively. The polymer molecular weight increases with decreasing dose rate, decreasing temperature, and increasing monomer concentration. These results are discussed in connection with the mechanism of heterogeneous polymerization and the solvent effect

Rubrene endoperoxide acetone monosolvate

Directory of Open Access Journals (Sweden)

Kiyoaki Shinashi

2012-04-01

Full Text Available The title acetone solvate, C42H28O2·C3H6O [systematic name: 1,3,10,12-tetraphenyl-19,20-dioxapentacyclo[10.6.2.02,11.04,9.013,18]icosa-2(11,3,5,7,9,13,15,17-octaene acetone monosolvate], is a photooxygenation product of rubrene (systematic name: 5,6,11,12-tetraphenyltetracene. The molecule bends at the bridgehead atoms, which are linked by the O—O transannular bond, with a dihedral angle of 49.21 (6° between the benzene ring and the naphthalene ring system of the tetracene unit. In the crystal, the rubrene molecules are linked by C—H...O hydrogen bonds into a column along the c axis. The acetone solvent molecules form a dimer around a crystallographic inversion centre through a carbonyl–carbonyl dipolar interaction. A C—H...O hydrogen bond between the rubrene and acetone molecules is also observed.

Obtaining uranium and/or vanadium values from solutions

Energy Technology Data Exchange (ETDEWEB)

Vojkovic, M

1982-04-22

A process for the recovery of at least one of uranium and vanadium from an aqueous liquor is claimed. It comprises: (a) treating the liquor with a low molecular weight completely water-miscible solvent selected from the group consisting of methanol, iso-propyl alcohol or acetone to form at least two phases; (b) separating the phases; (c) recovering the solvent from the first phase as the azeotropic solvent/water mixture by simple, non-fractional distillation and recycling the mixture to step (a); and (d) recovering metal values from a second one of the phases.

Acetone-based cellulose solvent.

Science.gov (United States)

Kostag, Marc; Liebert, Tim; Heinze, Thomas

2014-08-01

Acetone containing tetraalkylammonium chloride is found to be an efficient solvent for cellulose. The addition of an amount of 10 mol% (based on acetone) of well-soluble salt triethyloctylammonium chloride (Et3 OctN Cl) adjusts the solvent's properties (increases the polarity) to promote cellulose dissolution. Cellulose solutions in acetone/Et3 OctN Cl have the lowest viscosity reported for comparable aprotic solutions making it a promising system for shaping processes and homogeneous chemical modification of the biopolymer. Recovery of the polymer and recycling of the solvent components can be easily achieved. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydrophobic hydration of poly-N-isopropyl acrylamide: a matter of the mean energetic state of water

Science.gov (United States)

Bischofberger, I.; Calzolari, D. C. E.; de Los Rios, P.; Jelezarov, I.; Trappe, V.

2014-03-01

The enthalpically favoured hydration of hydrophobic entities, termed hydrophobic hydration, impacts the phase behaviour of numerous amphiphiles in water. Here, we show experimental evidence that hydrophobic hydration is strongly determined by the mean energetics of the aqueous medium. We investigate the aggregation and collapse of an amphiphilic polymer, poly-N-isopropyl acrylamide (PNiPAM), in aqueous solutions containing small amounts of alcohol and find that the thermodynamic characteristics defining the phase transitions of PNiPAM evolve relative to the solvent composition at which the excess mixing enthalpy of the water/alcohol mixtures becomes minimal. Such correlation between solvent energetics and solution thermodynamics extends to other mixtures containing neutral organic solutes that are considered as kosmotropes to induce a strengthening of the hydrogen bonded water network. This denotes the energetics of water as a key parameter controlling the phase behaviour of PNiPAM and identifies the excess mixing enthalpy of water/kosmotrope mixtures as a gauge of the kosmotropic effect on hydrophobic assemblies.

The Use of Liquid Isopropyl Alcohol and Hydrogen Peroxide Gas Plasma to Biologically Decontaminate Spacecraft Electronics

Science.gov (United States)

Bonner, J. K.; Tudryn, Carissa D.; Choi, Sun J.; Eulogio, Sebastian E.; Roberts, Timothy J.; Tudryn, Carissa D.

2006-01-01

Legitimate concern exists regarding sending spacecraft and their associated hardware to solar system bodies where they could possibly contaminate the body's surface with terrestrial microorganisms. The NASA approved guidelines for sterilization as set forth in NPG 8020.12C, which is consistent with the biological contamination control objectives of the Committee on Space Research (COSPAR), recommends subjecting the spacecraft and its associated hardware to dry heat-a dry heat regimen that could potentially employ a temperature of 110(deg)C for up to 200 hours. Such a temperature exposure could prove detrimental to the spacecraft electronics. The stimulated growth of intermetallic compounds (IMCs) in metallic interconnects and/or thermal degradation of organic materials composing much of the hardware could take place over a prolonged temperature regimen. Such detrimental phenomena would almost certainly compromise the integrity and reliability of the electronics. Investigation of sterilization procedures in the medical field suggests that hydrogen peroxide (H202) gas plasma (HPGP) technology can effectively function as an alternative to heat sterilization, especially for heat-sensitive items. Treatment with isopropyl alcohol (IPA) in liquid form prior to exposure of the hardware to HPGP should also prove beneficial. Although IPA is not a sterilant, it is frequently used as a disinfectant because of its bactericidal properties. The use of IPA in electronics cleaning is widely recognized and has been utilized for many years with no adverse affects reported. In addition, IPA is the principal ingredient of the test fluid used in ionic contamination testers to assess the amount of ionic contamination found on the surfaces of printed wiring assemblies. This paper will set forth experimental data confirming the feasibility of the IPA/H202 approach to reach acceptable microbial reduction (MR) levels of spacecraft electronic hardware. In addition, a proposed process flow in

Internal catalysis in imine formation from acetone and acetone-d6 and conformationally constrained derivatives of N,N-dimethyl-1,3-propanediamine

International Nuclear Information System (INIS)

Hine, J.; Li, W.S.

1975-01-01

The kinetics of the reactions of 3-exo-dimethylaminomethyl-2-endo-norbornanamine (1), cis-2-(dimethylaminomethyl)cyclohexylamine (2), and 3-endo-dimethylaminomethyl-2-endo-norbornanamine (3) with acetone, and of these three diamines, neopentylamine, and 2-endo-norbornanamine with acetone-d 6 to give imines were studied at 35 0 and various pH's by use of hydroxylamine to capture the imines as they are formed. Acetone-d 6 was more reactive than acetone in the reactions with hydroxylamine alone as well as in the reactions with each of the diamines; the average k/sup D//k/sup H/ was 1.2. The rate constants for the monoprotonated diamines were so large relative to those for the unprotonated diamines that reliable values for the latter could not be obtained. The dominant reaction mechanism appears to be a reversible formation of the carbinolamine derived from the tertiary-protonated form of the monoprotonated diamine followed by rate-controlling internal acid-catalyzed formation of the iminium ion. The rate constants are compared with those obtained as a by-product of deuterium exchange studies of reactions of 1, 2, 3, and five other monoprotonated diamines by the same mechanism. The comparisons show that structural features that destabilize conformations in which the two amino groups are far apart may decrease the reactivity by relative stabilization []of a cyclic hydrogen-bonded form of the monoprotonated diamine as well as increasing the reactivity by relative stabilization of the transition state. Freezing the H 2 N--C--C--CH 2 NMe 2 dihedral angle of 1,3-diamines at values near 0, 60, and 120 0 does not give large differences in reactivity. Comparison of the rate constants for reactions of unprotonated neopentylamine and 2-endo-norbornanamine with those obtained previously for amines of the type XCH 2 CH 2 NH 2 gives no evidence for steric hindrance. (auth)

Off-line breath acetone analysis in critical illness.

Science.gov (United States)

Sturney, S C; Storer, M K; Shaw, G M; Shaw, D E; Epton, M J

2013-09-01

Analysis of breath acetone could be useful in the Intensive Care Unit (ICU) setting to monitor evidence of starvation and metabolic stress. The aims of this study were to examine the relationship between acetone concentrations in breath and blood in critical illness, to explore any changes in breath acetone concentration over time and correlate these with clinical features. Consecutive patients, ventilated on controlled modes in a mixed ICU, with stress hyperglycaemia requiring insulin therapy and/or new pulmonary infiltrates on chest radiograph were recruited. Once daily, triplicate end-tidal breath samples were collected and analysed off-line by selected ion flow tube mass spectrometry (SIFT-MS). Thirty-two patients were recruited (20 males), median age 61.5 years (range 26-85 years). The median breath acetone concentration of all samples was 853 ppb (range 162-11 375 ppb) collected over a median of 3 days (range 1-8). There was a trend towards a reduction in breath acetone concentration over time. Relationships were seen between breath acetone and arterial acetone (rs = 0.64, p acetone concentration over time corresponded to changes in arterial acetone concentration. Some patients remained ketotic despite insulin therapy and normal arterial glucose concentrations. This is the first study to look at breath acetone concentration in ICU patients for up to 8 days. Breath acetone concentration may be used as a surrogate for arterial acetone concentration, which may in future have a role in the modulation of insulin and feeding in critical illness.

Enhancing acetone biosynthesis and acetone-butanol-ethanol fermentation performance by co-culturing Clostridium acetobutylicum/Saccharomyces cerevisiae integrated with exogenous acetate addition.

Science.gov (United States)

Luo, Hongzhen; Ge, Laibing; Zhang, Jingshu; Ding, Jian; Chen, Rui; Shi, Zhongping

2016-01-01

Acetone is the major by-product in ABE fermentations, most researches focused on increasing butanol/acetone ratio by decreasing acetone biosynthesis. However, economics of ABE fermentation industry strongly relies on evaluating acetone as a valuable platform chemical. Therefore, a novel ABE fermentation strategy focusing on bio-acetone production by co-culturing Clostridium acetobutylicum/Saccharomyces cerevisiae with exogenous acetate addition was proposed. Experimental and theoretical analysis revealed the strategy could, enhance C. acetobutylicum survival oriented amino acids assimilation in the cells; control NADH regeneration rate at moderately lower level to enhance acetone synthesis but without sacrificing butanol production; enhance the utilization ability of C. acetobutylicum on glucose and direct most of extra consumed glucose into acetone/butanol synthesis routes. By implementing the strategy using synthetic or acetate fermentative supernatant, acetone concentrations increased to 8.27-8.55g/L from 5.86g/L of the control, while butanol concentrations also elevated to the higher levels of 13.91-14.23g/L from 11.63g/L simultaneously. Copyright © 2015 Elsevier Ltd. All rights reserved.

Extraction of hafnium with chelating agents from aqueous-alcoholic solutions

International Nuclear Information System (INIS)

Hala, J.; Prihoda, J.

1975-01-01

The extraction was studied of hafnium into solutions of N-benzoyl-N-phenylhydroxylamine, 2-thenoyltrifluoroacetone and di-n-butylphosphoric acid in benzene, toluene, chloroform and tetrachloromethane from aqueous alcoholic solutions with a formal acidity of 2M-HClO 4 . Methyl-, ethyl-, n- and isopropyl- and tert-butyl alcohol were used as organic components in the mixed aqueous-organic phase. In the extraction into N-benzoyl-N-phenylhydroxylamine the presence of the alcohols resulted in synergic effects analogous to the previously described extraction by substituted benzoylpyrazolone. With the other two extractants, the effect of the alcohols was antagonistic, due to the interaction of alcohol or water with the reagent in the organic phase, and to the decrease in the reagent distribution constant. (author)

Acetone utilization by sulfate-reducing bacteria: draft genome sequence of Desulfococcus biacutus and a proteomic survey of acetone-inducible proteins.

Science.gov (United States)

Gutiérrez Acosta, Olga B; Schleheck, David; Schink, Bernhard

2014-07-11

The sulfate-reducing bacterium Desulfococcus biacutus is able to utilize acetone for growth by an inducible degradation pathway that involves a novel activation reaction for acetone with CO as a co-substrate. The mechanism, enzyme(s) and gene(s) involved in this acetone activation reaction are of great interest because they represent a novel and yet undefined type of activation reaction under strictly anoxic conditions. In this study, a draft genome sequence of D. biacutus was established. Sequencing, assembly and annotation resulted in 159 contigs with 5,242,029 base pairs and 4773 predicted genes; 4708 were predicted protein-encoding genes, and 3520 of these had a functional prediction. Proteins and genes were identified that are specifically induced during growth with acetone. A thiamine diphosphate-requiring enzyme appeared to be highly induced during growth with acetone and is probably involved in the activation reaction. Moreover, a coenzyme B12- dependent enzyme and proteins that are involved in redox reactions were also induced during growth with acetone. We present for the first time the genome of a sulfate reducer that is able to grow with acetone. The genome information of this organism represents an important tool for the elucidation of a novel reaction mechanism that is employed by a sulfate reducer in acetone activation.

Portable method of measuring gaseous acetone concentrations.

Science.gov (United States)

Worrall, Adam D; Bernstein, Jonathan A; Angelopoulos, Anastasios P

2013-08-15

Measurement of acetone in human breath samples has been previously shown to provide significant non-invasive diagnostic insight into the control of a patient's diabetic condition. In patients with diabetes mellitus, the body produces excess amounts of ketones such as acetone, which are then exhaled during respiration. Using various breath analysis methods has allowed for the accurate determination of acetone concentrations in exhaled breath. However, many of these methods require instrumentation and pre-concentration steps not suitable for point-of-care use. We have found that by immobilizing resorcinol reagent into a perfluorosulfonic acid polymer membrane, a controlled organic synthesis reaction occurs with acetone in a dry carrier gas. The immobilized, highly selective product of this reaction (a flavan) is found to produce a visible spectrum color change which could measure acetone concentrations to less than ppm. We here demonstrate how this approach can be used to produce a portable optical sensing device for real-time, non-invasive acetone analysis. Copyright © 2013 Elsevier B.V. All rights reserved.

Phage inactivation by triplet acetone

International Nuclear Information System (INIS)

Gomes, R.A.

1985-01-01

The exposure of lambda phage to triplet acetone is studied. The triplet acetone is obtained from aerobic oxidation of isobutanal catalysed by peroxidase. A decrease of lambda phage ability to infect Escherichia coli is reported, perhaps, partially due to the possible production of lesions in the phage genome. (M.A.C.) [pt

Gas phase toluene isopropylation over high silica mordenite

Indian Academy of Sciences (India)

Administrator

reaction on medium pore HZSM-5 zeolites differing in crystal size and ... effect of various parameters on the yield and cy- ... toluene. (DIPT) + water (cymene isopropylation) .... tain the stability of the mordenite catalysts. .... From the slope of the.

Oxidation of tertiary homoallylic alcohols by thallium trinitrate: fragmentation versus ring contraction

International Nuclear Information System (INIS)

Silva Junior, Luiz F.; Quintiliano, Samir A.P.; Ferraz, Helena M.C.; Santos, Leonardo S.; Eberlin, Marcos N.

2006-01-01

The oxidation of tertiary homoallylic alcohols with thallium trinitrate (TTN) was investigated. The alcohols bearing an allylic methyl group lose a molecule of acetone via a fragmentation reaction that leads to isomeric secondary allylic alcohols as major products, together with their corresponding acetylated derivatives. On the other hand, treating analogous tertiary alcohols without the allylic methyl group with TTN gives indans, through a ring contraction reaction. (author)

Analysis of the origin and importance of acetone and isopropanol levels in the blood of the deceased for medico-legal testimony.

Science.gov (United States)

Borowska-Solonynko, A; Siwińska-Ziółkowska, A; Piotrkowicz, M; Wysmołek, M; Demkow, M

2014-01-01

The aim of the study was to analyze the incidence of acetone and isopropanol in the blood of the deceased, and to assess cases in which the compounds have been detected with a focus on their origin and usefulness for medico-legal testimony. The study material consisted of results of tests detecting ethyl alcohol and reports of autopsies performed at the Department of Forensic Medicine, Medical University of Warsaw, from January 2008 to April 2009 - a total of 2,475 cases. The test group proper (group B) comprised only those cases in which acetone was detected in blood, either with or without isopropanol [n = 202 (8.2%)]. The blood levels of isopropanol varied depending on the cause of death. The need for differentiating the origin of isopropanol in the case of its presence in the blood of the deceased was pointed out. The results of the present study show that the differentiation should be based on the isopropanol and acetone concentration ratio, as isopropanol concentration alone is not sufficient for preparing expert opinions. Even high concentrations of isopropanol, when accompanied by even higher concentrations of acetone, imply that isopropanol could have been formed as a result of acetone transformations. Isopropanol concentrations exceeding acetone levels strongly point to the exogenous origin of isopropanol, particularly when high levels of ethanol are concurrently detected.

Nitrate-Dependent Degradation of Acetone by Alicycliphilus and Paracoccus Strains and Comparison of Acetone Carboxylase Enzymes ▿

Science.gov (United States)

Dullius, Carlos Henrique; Chen, Ching-Yuan; Schink, Bernhard

2011-01-01

A novel acetone-degrading, nitrate-reducing bacterium, strain KN Bun08, was isolated from an enrichment culture with butanone and nitrate as the sole sources of carbon and energy. The cells were motile short rods, 0.5 to 1 by 1 to 2 μm in size, which gave Gram-positive staining results in the exponential growth phase and Gram-negative staining results in the stationary-growth phase. Based on 16S rRNA gene sequence analysis, the isolate was assigned to the genus Alicycliphilus. Besides butanone and acetone, the strain used numerous fatty acids as substrates. An ATP-dependent acetone-carboxylating enzyme was enriched from cell extracts of this bacterium and of Alicycliphilus denitrificans K601T by two subsequent DEAE Sepharose column procedures. For comparison, acetone carboxylases were enriched from two additional nitrate-reducing bacterial species, Paracoccus denitrificans and P. pantotrophus. The products of the carboxylase reaction were acetoacetate and AMP rather than ADP. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) analysis of cell extracts and of the various enzyme preparations revealed bands corresponding to molecular masses of 85, 78, and 20 kDa, suggesting similarities to the acetone carboxylase enzymes described in detail for the aerobic bacterium Xanthobacter autotrophicus strain Py2 (85.3, 78.3, and 19.6 kDa) and the phototrophic bacterium Rhodobacter capsulatus. Protein bands were excised and compared by mass spectrometry with those of acetone carboxylases of aerobic bacteria. The results document the finding that the nitrate-reducing bacteria studied here use acetone-carboxylating enzymes similar to those of aerobic and phototrophic bacteria. PMID:21841031

Fate of acetone in water

Science.gov (United States)

Rathbun, R.E.; Stephens, D.W.; Shultz, D.J.

1982-01-01

The physical, chemical, and biological processes that might affect the concentration of acetone in water were investigated in laboratory studies. Processes considered included volatilization, adsorption by sediments, photodecomposition, bacterial degradation, and absorption by algae and molds. It was concluded that volatilization and bacterial degradation were the dominant processes determining the fate of acetone in streams and rivers. ?? 1982.

Quantitative Clinical Diagnostic Analysis of Acetone in Human Blood by HPLC: A Metabolomic Search for Acetone as Indicator

Directory of Open Access Journals (Sweden)

Esin Akgul Kalkan

2016-01-01

Full Text Available Using high-performance liquid chromatography (HPLC and 2,4-dinitrophenylhydrazine (2,4-DNPH as a derivatizing reagent, an analytical method was developed for the quantitative determination of acetone in human blood. The determination was carried out at 365 nm using an ultraviolet-visible (UV-Vis diode array detector (DAD. For acetone as its 2,4-dinitrophenylhydrazone derivative, a good separation was achieved with a ThermoAcclaim C18 column (15 cm × 4.6 mm × 3 μm at retention time (tR 12.10 min and flowrate of 1 mL min−1 using a (methanol/acetonitrile water elution gradient. The methodology is simple, rapid, sensitive, and of low cost, exhibits good reproducibility, and allows the analysis of acetone in biological fluids. A calibration curve was obtained for acetone using its standard solutions in acetonitrile. Quantitative analysis of acetone in human blood was successfully carried out using this calibration graph. The applied method was validated in parameters of linearity, limit of detection and quantification, accuracy, and precision. We also present acetone as a useful tool for the HPLC-based metabolomic investigation of endogenous metabolism and quantitative clinical diagnostic analysis.

Outbreak of carbon tetrachloride poisoning in a color printing factory related to the use of isopropyl alcohol and an air conditioning system in Taiwan.

Science.gov (United States)

Deng, J F; Wang, J D; Shih, T S; Lan, F L

1987-01-01

Three workers from a color printing factory were admitted to community hospitals in 1985 with manifestations of acute hepatitis. One of the three had superimposed acute renal failure and pulmonary edema. An investigation was subsequently conducted at the plant to determine the etiology of the outbreak and the prevalence of liver disease among the remaining workers. Comprehensive medical evaluations were conducted, which included physical examinations, liver function tests, and serological screening for hepatitis. Seventeen of 25 workers from the plant had abnormal liver function tests 10 days after the outbreak, and a significant association was found between the presence of abnormal liver function tests and a history of recently having worked inside any of three rooms in which an interconnecting air conditioning system had been installed to cool the printing machines. After further investigation, it was determined that the incident occurred following inadvertent use of carbon tetrachloride to clean a pump in the printing machine. A simulation of the pump cleaning operation revealed ambient air levels of carbon tetrachloride of 300-500 ppm. Ultimately, it was concluded that the outbreak was in all likelihood due to the combined use of carbon tetrachloride and isopropyl alcohol in the cleaning operation. This outbreak underscores the importance of adopting appropriate industrial hygiene measures in a rapidly industrializing nation such as Taiwan.

Marine Vibrio Species Produce the Volatile Organic Compound Acetone

OpenAIRE

Nemecek-Marshall, M.; Wojciechowski, C.; Kuzma, J.; Silver, G. M.; Fall, R.

1995-01-01

While screening aerobic, heterotrophic marine bacteria for production of volatile organic compounds, we found that a group of isolates produced substantial amounts of acetone. Acetone production was confirmed by gas chromatography, gas chromatography-mass spectrometry, and high-performance liquid chromatography. The major acetone producers were identified as nonclinical Vibrio species. Acetone production was maximal in the stationary phase of growth and was stimulated by addition of l-leucine...

Gas phase toluene isopropylation over high silica mordenite

Indian Academy of Sciences (India)

Mordenite (HM) catalysts with three different Si/Al ratios were compared for their activity and selectivities in gas phase toluene isopropylation with isopropanol. Catalyst with Si/Al ratio 44.9 offered better cumene selectivity, hence, it was chosen for detailed kinetic investigations. The influence of various process parameters ...

Measuring breath acetone for monitoring fat loss: Review.

Science.gov (United States)

Anderson, Joseph C

2015-12-01

Endogenous acetone production is a by-product of the fat metabolism process. Because of its small size, acetone appears in exhaled breath. Historically, endogenous acetone has been measured in exhaled breath to monitor ketosis in healthy and diabetic subjects. Recently, breath acetone concentration (BrAce) has been shown to correlate with the rate of fat loss in healthy individuals. In this review, the measurement of breath acetone in healthy subjects is evaluated for its utility in predicting fat loss and its sensitivity to changes in physiologic parameters. BrAce can range from 1 ppm in healthy non-dieting subjects to 1,250 ppm in diabetic ketoacidosis. A strong correlation exists between increased BrAce and the rate of fat loss. Multiple metabolic and respiratory factors affect the measurement of BrAce. BrAce is most affected by changes in the following factors (in descending order): dietary macronutrient composition, caloric restriction, exercise, pulmonary factors, and other assorted factors that increase fat metabolism or inhibit acetone metabolism. Pulmonary factors affecting acetone exchange in the lung should be controlled to optimize the breath sample for measurement. When biologic factors are controlled, BrAce measurement provides a non-invasive tool for monitoring the rate of fat loss in healthy subjects. © 2015 The Authors Obesity published by Wiley Periodicals, Inc. on behalf of The Obesity Society (TOS).

Comparison studies of surface cleaning methods for PAN-based carbon fibers with acetone, supercritical acetone and subcritical alkali aqueous solutions

International Nuclear Information System (INIS)

Meng Linghui; Fan Dapeng; Huang Yudong; Jiang Zaixing; Zhang Chunhua

2012-01-01

Highlights: ► Cleaning with supercritical acetone is appropriate to wipe off the oxygenated contaminants. ► Cleaning with supercritical acetone causes smaller damage to bulk strength of carbon fibers. ► Cleaning with subcritical alkali aqueous solution can thoroughly remove silicious contaminants. - Abstract: Four kinds of polyacrylonitrile-based carbon fibers were cleaned by three methods and were characterized by X-ray photoelectron spectroscopy, monofilament tensile strength test and atomic force microscopy (AFM). Experimental results of these tests reveal that the method using supercritical acetone or subcritical potassium hydroxide aqueous solution act as the processing medium shows a better cleaning effect compared to the traditional method, Soxhlet extraction with acetone. The method using supercritical acetone is more appropriate to wipe off the oxygenated contaminants on carbon fibers’ surfaces and causes a relatively smaller damage to the bulk strength of each carbon fiber. As far as treating method using the subcritical alkali aqueous solution, it can thoroughly remove silicious contaminants on the surfaces of treated fibers.

Isopropylation of benzene with 2-propanol over substituted large ...

Indian Academy of Sciences (India)

3. The major draw- back of these catalysts is their corrosive and envi- ronmentally hazardous ... catalytic activity towards vapor phase isopropylation of benzene with ... 2 cm i.d. The glass reactor was heated to the requi- site temperature with ...

Surface tension anomalies in room temperature ionic liquids-acetone solutions

Science.gov (United States)

Abe, Hiroshi; Murata, Keisuke; Kiyokawa, Shota; Yoshimura, Yukihiro

2018-05-01

Surface tension anomalies were observed in room temperature ionic liquid (RTIL)-acetone solutions. The RTILs are 1-alkyl-3-methylimidazorium iodide with [Cnmim][I] in a [Cnmim][I]-x mol% acetone. The maximum value of the surface tension appeared at 40 mol% acetone, although density decreased monotonically with an increase in acetone concentration. A small alkyl chain length effect of the Cnmim+ cations was observed in the surface tension. By the Gibbs adsorption isotherm, it was found that I- anion-mediated surface structure became dominant above 40 mol%. In the different [Cnmim][TFSI]-acetone mixtures, normal decay of the surface tension was observed on the acetone concentration scale, where TFSI- is bis(trifluoromethanesulfonyl)imide.

Products and mechanism of the reaction of Cl atoms with unsaturated alcohols

Science.gov (United States)

Rodríguez, Ana; Rodríguez, Diana; Soto, Amparo; Bravo, Iván; Diaz-de-Mera, Yolanda; Notario, Alberto; Aranda, Alfonso

2012-04-01

The products of the chlorine atom initiated oxidation of different unsaturated alcohols were determined at atmospheric pressure and ambient temperature, in a 400 L teflon reaction chamber using GC-FID and GC-MS for the analysis. The major products detected (with molar yields in brackets) are: chloroacetaldehyde (50 ± 8%) and acrolein (27 ± 2%) from allyl alcohol; acetaldehyde (77 ± 11%), chloroacetaldehyde (75 ± 18%), and methyl vinyl ketone (17 ± 2%) from 3-buten-2-ol; acetone (55 ± 4%) and chloroacetaldehyde (59 ± 8%) from 2-methyl-3-buten-2-ol; chloroacetone (18 ± 1%) and methacrolein (8 ± 1%) from 2-methyl-2-propen-1-ol; acetaldehyde (20 ± 1%), crotonaldehyde (6 ± 3%), 3-choloro-4-hydroxy-2-butanone (2 ± 2%) and 2-chloro-propanal (4 ± 5%) from crotyl alcohol; and acetone (24 ± 3%) from 3-methyl-2-buten-1-ol. The experimental data suggests that addition of Cl to the double bond of the unsaturated alcohol is the dominant reaction pathway compared to the H-abstraction channel.

Acetone utilization by sulfate-reducing bacteria: draft genome sequence of Desulfococcus biacutus and a proteomic survey of acetone-inducible proteins

OpenAIRE

Gutiérrez Acosta, Olga B; Schleheck, David; Schink, Bernhard

2014-01-01

Background The sulfate-reducing bacterium Desulfococcus biacutus is able to utilize acetone for growth by an inducible degradation pathway that involves a novel activation reaction for acetone with CO as a co-substrate. The mechanism, enzyme(s) and gene(s) involved in this acetone activation reaction are of great interest because they represent a novel and yet undefined type of activation reaction under strictly anoxic conditions. Results In this study, a draft genome sequence of D. biacutus ...

46 CFR 153.1035 - Acetone cyanohydrin or lactonitrile solutions.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Acetone cyanohydrin or lactonitrile solutions. 153.1035... Special Cargo Procedures § 153.1035 Acetone cyanohydrin or lactonitrile solutions. No person may operate a tankship carrying a cargo of acetone cyanohydrin or lactonitrile solutions, unless that cargo is stabilized...

Cloning, functional expression and characterization of a bifunctional 3-hydroxybutanal dehydrogenase /reductase involved in acetone metabolism by Desulfococcus biacutus.

Science.gov (United States)

Frey, Jasmin; Rusche, Hendrik; Schink, Bernhard; Schleheck, David

2016-11-25

The strictly anaerobic, sulfate-reducing bacterium Desulfococcus biacutus can utilize acetone as sole carbon and energy source for growth. Whereas in aerobic and nitrate-reducing bacteria acetone is activated by carboxylation with CO 2 to acetoacetate, D. biacutus involves CO as a cosubstrate for acetone activation through a different, so far unknown pathway. Proteomic studies indicated that, among others, a predicted medium-chain dehydrogenase/reductase (MDR) superfamily, zinc-dependent alcohol dehydrogenase (locus tag DebiaDRAFT_04514) is specifically and highly produced during growth with acetone. The MDR gene DebiaDRAFT_04514 was cloned and overexpressed in E. coli. The purified recombinant protein required zinc as cofactor, and accepted NADH/NAD + but not NADPH/NADP + as electron donor/acceptor. The pH optimum was at pH 8, and the temperature optimum at 45 °C. Highest specific activities were observed for reduction of C 3 - C 5 -aldehydes with NADH, such as propanal to propanol (380 ± 15 mU mg -1 protein), butanal to butanol (300 ± 24 mU mg -1 ), and 3-hydroxybutanal to 1,3-butanediol (248 ± 60 mU mg -1 ), however, the enzyme also oxidized 3-hydroxybutanal with NAD + to acetoacetaldehyde (83 ± 18 mU mg -1 ). The enzyme might play a key role in acetone degradation by D. biacutus, for example as a bifunctional 3-hydroxybutanal dehydrogenase/reductase. Its recombinant production may represent an important step in the elucidation of the complete degradation pathway.

Application of butyl alcohol bacteria for the fermentation of nonnutritive raw materials

Energy Technology Data Exchange (ETDEWEB)

Nakhamanovich, B M; Senkevich, V V; Yarovenko, V L

1961-01-01

Materials like corncobs after hydrolysis can be economically fermented by using bacteria which support a butyl alcohol-acetone fermentation. Best results are obtained if (NH/sub 4/)/sub 2/SO/sub 4/ and superphosphate are added to the fermentation liquor. Analyses are presnted of the hydrolzates (alcohols, formic acid, 2-furaldehyde, and reducing sugars) and of the final products.

Effects of organic solvents on hyaluronic acid nanoparticles obtained by precipitation and chemical crosslinking.

Science.gov (United States)

Bicudo, Rafaela Costa Souza; Santana, Maria Helena Andrade

2012-03-01

Hyaluronic acid is a hydrophilic mucopolysaccharide composed of alternating units of D-glucuronic acid and N-acetylglucosamine. It is used in many medical, pharmaceutical, and cosmetic applications, as sponges, films, or particle formulations. Hyaluronic acid nanoparticles can be synthesized free of oil and surfactants by nanoprecipitation in organic solvents, followed by chemical crosslinking. The organic solvent plays an important role in particles size and structure. Therefore, this study aimed to investigate the influence of acetone, ethanol, and isopropyl alcohol on the synthesis and physico-chemical properties of hyaluronic acid nanoparticles. Particles were crosslinked with adipic hydrazide and chloride carbodiimide under controlled conditions. The nanoparticles obtained with all three studied solvents were moderately electrostatically stable. Experiments with acetone produced the smallest particle size (120.44 nm) and polydispersity (0.27). The size and polydispersity of hyaluronic acid nanoparticles correlated with the surface tension between water and the organic solvents, not with the thermodynamic affinity of water for the organic solvents.

Acetone n-radical cation internal rotation spectrum: The torsional potential surface

International Nuclear Information System (INIS)

Shea, Dana A.; Goodman, Lionel; White, Michael G.

2000-01-01

The one color REMPI and two color ZEKE-PFI spectra of acetone-d 3 have been recorded. The 3p x Rydberg state of acetone-d 3 lies at 59 362.3 cm-1 and both of the torsional modes are visible in this spectrum. The antigearing Rydberg (a 2 ) mode, v 12 * , has a frequency of 62.5 cm-1, while the previously unobserved gearing (b 1 ) mode, v 17 * , is found at 119.1 cm-1. An ionization potential of 78 299.6 cm-1 for acetone-d 3 has been measured. In acetone-d 3 n-radical cation ground state, the fundamentals of both of the torsional modes have been observed, v 12 + at 51.0 cm-1 and v 17 + at 110.4 cm-1, while the first overtone of v 12 + has been measured at 122.4 cm-1. Deuterium shifts show that v 12 + behaves like a local C 3v rotor, but that v 17 + is canonical. Combining this data with that for acetone-d 0 and aacetone-d 6 has allowed us to fit the observed frequencies to a torsional potential energy surface based on an ab initio C 2v cation ground state geometry. This potential energy surface allows for prediction of the v 17 vibration in acetone-d 0 and acetone-d 6 . The barrier to synchronous rotation is higher in the cation ground state than in the neutral ground state, but significantly lower than in the 3s Rydberg state. The 3p x Rydberg and cation ground state potential energy surfaces are found to be very similar to each other, strongly supporting the contention that the 3p x Rydberg state has C 2v geometry and is a good model for the ion core. The altered 3s Rydberg state potential surface suggests this state has significant valence character. (c) 2000 American Institute of Physics

Proteomic analysis of nitrate-dependent acetone degradation by Alicycliphilus denitrificans strain BC.

Science.gov (United States)

Oosterkamp, Margreet J; Boeren, Sjef; Atashgahi, Siavash; Plugge, Caroline M; Schaap, Peter J; Stams, Alfons J M

2015-06-01

Alicycliphilus denitrificans strain BC grows anaerobically on acetone with nitrate as electron acceptor. Comparative proteomics of cultures of A. denitrificans strain BC grown on either acetone or acetate with nitrate was performed to study the enzymes involved in the acetone degradation pathway. In the proposed acetone degradation pathway, an acetone carboxylase converts acetone to acetoacetate, an AMP-dependent synthetase/ligase converts acetoacetate to acetoacetyl-CoA, and an acetyl-CoA acetyltransferase cleaves acetoacetyl-CoA to two acetyl-CoA. We also found a putative aldehyde dehydrogenase associated with acetone degradation. This enzyme functioned as a β-hydroxybutyrate dehydrogenase catalyzing the conversion of surplus acetoacetate to β-hydroxybutyrate that may be converted to the energy and carbon storage compound, poly-β-hydroxybutyrate. Accordingly, we confirmed the formation of poly-β-hydroxybutyrate in acetone-grown cells of strain BC. Our findings provide insight in nitrate-dependent acetone degradation that is activated by carboxylation of acetone. This will aid studies of similar pathways found in other microorganisms degrading acetone with nitrate or sulfate as electron acceptor. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Isopropylation of benzene with 2-propanol over substituted large ...

Indian Academy of Sciences (India)

The catalytic performance of these materials was tested for isopropylation of benzene with 2-propanol at 250, 300, 350 and 400°C. The products were cumene, -DIPB (-diisopropylbenzene) and -DIPB (-diisopropylbenzene). MnAPO-5 was found to be more active than the other catalysts. Maximum conversion (20%) ...

Toward Portable Breath Acetone Analysis for Diabetes Detection

Science.gov (United States)

Righettoni, Marco; Tricoli, Antonio

2013-01-01

Diabetes is a lifelong condition that may cause death and seriously affects the quality of life of a rapidly growing number of individuals. Acetone is a selective breath marker for diabetes that may contribute to the monitoring of related metabolic disorder and thus simplify the management of this illness. Here, the overall performance of Si-doped WO3 nanoparticles made by flame spray pyrolysis as portable acetone detectors is critically reviewed focusing on the requirements for medical diagnostic. The effect of flow rate, chamber volume and acetone dissociation within the measuring chamber are discussed with respect to the calibration of the sensor response. The challenges for the fabrication of portable breath acetone sensors based on chemo-resistive detectors are underlined indicating possible solutions and novel research directions. PMID:21828897

Evaporation Kinetics in Short-Chain Alcohols by Optical Interference

Science.gov (United States)

Rosbrugh, Ian M.; Nishimura, S. Y.; Nishimura, A. M.

2000-08-01

The evaporation rates of volatile organic liquids may be determined through the observation of optical interference of spatially coincident light that is reflected from the top (air-liquid) and bottom (liquid-surface) of a liquid drop on a glass surface. As an example of what is possible with this technique, the evaporation for a series of short-chain alcohols and acetone was investigated. For 1-propanol, 2-propanol, 2-methyl-1-propanol, and acetone, the kinetics of evaporation was determined to be zero order. For methanol and ethanol, the process was significantly higher than zero order.

Acetone in the atmosphere: Distribution, sources, and sinks

Science.gov (United States)

Singh, H. B.; O'Hara, D.; Herlth, D.; Sachse, W.; Blake, D. R.; Bradshaw, J. D.; Kanakidou, M.; Crutzen, P. J.

1994-01-01

Acetone (CH3COCH3) was found to be the dominant nonmethane organic species present in the atmosphere sampled primarily over eastern Canada (0-6 km, 35 deg-65 deg N) during ABLE3B (July to August 1990). A concentration range of 357 to 2310 ppt (= 10(exp -12) v/v) with a mean value of 1140 +/- 413 ppt was measured. Under extremely clean conditions, generally involving Arctic flows, lowest (background) mixing ratios of 550 +/- 100 ppt were present in much of the troposphere studied. Correlations between atmospheric mixing ratios of acetone and select species such as C2H2, CO, C3H8, C2Cl4 and isoprene provided important clues to its possible sources and to the causes of its atmospheric variability. Biomass burning as a source of acetone has been identified for the first time. By using atmospheric data and three-dimensional photochemical models, a global acetone source of 40-60 Tg (= 10(exp 12) g)/yr is estimated to be present. Secondary formation from the atmospheric oxidation of precursor hydrocarbons (principally propane, isobutane, and isobutene) provides the single largest source (51%). The remainder is attributable to biomass burning (26%), direct biogenic emissions (21%), and primary anthropogenic emissions (3%). Atmospheric removal of acetone is estimated to be due to photolysis (64%), reaction with OH radicals (24%), and deposition (12%). Model calculations also suggest that acetone photolysis contributed significantly to PAN formation (100-200 ppt) in the middle and upper troposphere of the sampled region and may be important globally. While the source-sink equation appears to be roughly balanced, much more atmospheric and source data, especially from the southern hemisphere, are needed to reliably quantify the atmospheric budget of acetone.

Thermodynamics of Hydrogen Production from Dimethyl Ether Steam Reforming and Hydrolysis

Energy Technology Data Exchange (ETDEWEB)

T.A. Semelsberger

2004-10-01

The thermodynamic analyses of producing a hydrogen-rich fuel-cell feed from the process of dimethyl ether (DME) steam reforming were investigated as a function of steam-to-carbon ratio (0-4), temperature (100 C-600 C), pressure (1-5 atm), and product species: acetylene, ethanol, methanol, ethylene, methyl-ethyl ether, formaldehyde, formic acid, acetone, n-propanol, ethane and isopropyl alcohol. Results of the thermodynamic processing of dimethyl ether with steam indicate the complete conversion of dimethyl ether to hydrogen, carbon monoxide and carbon dioxide for temperatures greater than 200 C and steam-to-carbon ratios greater than 1.25 at atmospheric pressure (P = 1 atm). Increasing the operating pressure was observed to shift the equilibrium toward the reactants; increasing the pressure from 1 atm to 5 atm decreased the conversion of dimethyl ether from 99.5% to 76.2%. The order of thermodynamically stable products in decreasing mole fraction was methane, ethane, isopropyl alcohol, acetone, n-propanol, ethylene, ethanol, methyl-ethyl ether and methanol--formaldehyde, formic acid, and acetylene were not observed. The optimal processing conditions for dimethyl ether steam reforming occurred at a steam-to-carbon ratio of 1.5, a pressure of 1 atm, and a temperature of 200 C. Modeling the thermodynamics of dimethyl ether hydrolysis (with methanol as the only product considered), the equilibrium conversion of dimethyl ether is limited. The equilibrium conversion was observed to increase with temperature and steam-to-carbon ratio, resulting in a maximum dimethyl ether conversion of approximately 68% at a steam-to-carbon ratio of 4.5 and a processing temperature of 600 C. Thermodynamically, dimethyl ether processed with steam can produce hydrogen-rich fuel-cell feeds--with hydrogen concentrations exceeding 70%. This substantiates dimethyl ether as a viable source of hydrogen for PEM fuel cells.

Mechanistic Investigation of Molybdate-Catalysed Transfer Hydrodeoxygenation.

Science.gov (United States)

Larsen, Daniel B; Petersen, Allan R; Dethlefsen, Johannes R; Teshome, Ayele; Fristrup, Peter

2016-11-07

The molybdate-catalysed transfer hydrodeoxygenation (HDO) of benzyl alcohol to toluene driven by oxidation of the solvent isopropyl alcohol to acetone has been investigated by using a combination of experimental and computational methods. A Hammett study that compared the relative rates for the transfer HDO of five para-substituted benzylic alcohols was carried out. Density-functional theory (DFT) calculations suggest a transition state with significant loss of aromaticity contributes to the lack of linearity observed in the Hammett study. The transfer HDO could also be carried out in neat PhCH 2 OH at 175 °C. Under these conditions, PhCH 2 OH underwent disproportionation to yield benzaldehyde, toluene, and significant amounts of bibenzyl. Isotopic-labelling experiments (using PhCH 2 OD and PhCD 2 OH) showed that incorporation of deuterium into the resultant toluene originated from the α position of benzyl alcohol, which is in line with the mechanism suggested by the DFT study. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Impedimetric detection of alcohol vapours using nanostructured zinc ferrite.

Science.gov (United States)

Kannan, Padmanathan Karthick; Saraswathi, Ramiah

2014-11-01

A comparative study on the sensing characteristics of nanostructured zinc ferrite to three primary alcohols viz. methanol, ethanol and propanol has been carried out. The zinc ferrite has been prepared by a combustion method and characterized by XRD, FTIR, AFM and SEM. Impedance studies in the alcohol concentration range varying from 100 to 1000 ppm show definite variations in response to both the nature of the alcohol and its concentration. The nanostructured zinc ferrite shows the highest sensor response to methanol and least to propanol. Equivalent circuit modelling and calibration have been made for all the three alcohol sensors. The material shows a better selectivity to the alcohols compared to formaldehyde, ammonia and acetone vapours. Copyright © 2014 Elsevier B.V. All rights reserved.

Maximizing recovery of water-soluble proteins through acetone precipitation.

Science.gov (United States)

Crowell, Andrew M J; Wall, Mark J; Doucette, Alan A

2013-09-24

Solvent precipitation is commonly used to purify protein samples, as seen with the removal of sodium dodecyl sulfate through acetone precipitation. However, in its current practice, protein loss is believed to be an inevitable consequence of acetone precipitation. We herein provide an in depth characterization of protein recovery through acetone precipitation. In 80% acetone, the precipitation efficiency for six of 10 protein standards was poor (ca. ≤15%). Poor recovery was also observed for proteome extracts, including bacterial and mammalian cells. As shown in this work, increasing the ionic strength of the solution dramatically improves the precipitation efficiency of individual proteins, and proteome mixtures (ca. 80-100% yield). This is obtained by including 1-30 mM NaCl, together with acetone (50-80%) which maximizes protein precipitation efficiency. The amount of salt required to restore the recovery correlates with the amount of protein in the sample, as well as the intrinsic protein charge, and the dielectric strength of the solution. This synergistic approach to protein precipitation in acetone with salt is consistent with a model of ion pairing in organic solvent, and establishes an improved method to recover proteins and proteome mixtures in high yield. Copyright © 2013 Elsevier B.V. All rights reserved.

Synthesis of Acetone-Derived C6 , C9 , and C12 Carbon Scaffolds for Chemical and Fuel Applications.

Science.gov (United States)

Moore, Cameron M; Jenkins, Rhodri W; Janicke, Michael T; Kubic, William L; Polikarpov, Evgueni; Semelsberger, Troy A; Sutton, Andrew D

2016-12-20

A simple, inexpensive catalyst system (Amberlyst 15 and Ni/SiO 2 -Al 2 O 3 ) is described for the upgrading of acetone to a range of chemicals and potential fuels. Stepwise hydrodeoxygenation of the produced ketones can yield branched alcohols, alkenes, and alkanes. An analysis of these products is provided, which demonstrates that this approach can provide a product profile of valuable bioproducts and potential biofuels. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Small-angle neutron scattering study of D2O-alcohol solutions

International Nuclear Information System (INIS)

D'Arrigo, G.

1990-01-01

Small-angle neutron scattering (SANS) measurements have been carried out on heavy water solutions of ethanol, isopropyl alcohol, n-propyl alcohol, t-butyl alcohol and butoxyethanol between 5 and 37 0 C at the concentrations where ultrasonic attenuation exhibits peak values. The wavevector dependence and the absolute intensity of the scattered intensities were analysed according to a microscopic model of the solutions in terms of aggregated complexes. The results indicate that at 25 0 C there exist either alcohol 'micelle-like' structures or alcohol-heavy water complexes which increase on going from the lower to higher alcohol solutions. As temperature increases from 25 to 37 0 C a higher aggregation is observed in butyl alcohol and butoxyethanol solutions. This behaviour is attributed to the demixing tendency of these systems at high temperatures. On going from 25 to 5 0 C the aggregation increases again. This trend is associated with the anomalous behaviour of the specific heat and ultrasonic attenuation of these systems. The occurrence of a low-temperature phase transition suggested by these anomalies is supported by our results. (author)

Effects of humus on acetone-butanol fermentations

Energy Technology Data Exchange (ETDEWEB)

Kovats, J

1963-01-01

Adding 6 to 8 g humus-rich soil dried at 80/sup 0/ to 100 cc sterilized molasses, containing 3.8 sucrose and 0.1% (NH/sub 4/)/sub 2/HPO/sub 4/, inoculated with acetone-butanol fermentative bacteria, increased acetone, butanol, and ethanol yields by 30, 50, and 40%, respectively. The acetone-to-butanol ratio increased from 1.85 to 2.1-2.3 in low and 2.6-2.8 in high sucrose-molasses concentrations. Yields of total organic solvents increased from 25 to 36-8% of the sucrose present. Inorganic salts from ashed humus soils were only 10 to 20% less effective in enhancing fermentation than the whole soil. It is postulated that the fermentation is enhanced by trace elements present in the soil.

Breath acetone concentration; biological variability and the influence of diet

International Nuclear Information System (INIS)

Španěl, Patrik; Dryahina, Kseniya; Rejšková, Alžběta; Chippendale, Thomas W E; Smith, David

2011-01-01

Previous measurements of acetone concentrations in the exhaled breath of healthy individuals and the small amount of comparable data for individuals suffering from diabetes are briefly reviewed as a prelude to the presentation of new data on the sporadic and wide variations of breath acetone that occur in ostensibly healthy individuals. Data are also presented which show that following a ketogenic diet taken by eight healthy individuals their breath acetone concentrations increased up to five times over the subsequent 6 h. Similarly, the breath acetone increased six and nine times when a low carbohydrate diet was taken by two volunteers and remained high for the several days for which the diet was continued. These new data, together with the previous data, clearly indicate that diet and natural intra-individual biological and diurnal variability result in wide variations in breath acetone concentration. This places an uncertainty in the use of breath acetone alone to monitor blood glucose and glycaemic control, except and unless the individual acts as their own control and is cognizant of the need for dietary control. (note)

Activation of Acetone and Other Simple Ketones in Anaerobic Bacteria.

Science.gov (United States)

Heider, Johann; Schühle, Karola; Frey, Jasmin; Schink, Bernhard

2016-01-01

Acetone and other ketones are activated for subsequent degradation through carboxylation by many nitrate-reducing, phototrophic, and obligately aerobic bacteria. Acetone carboxylation leads to acetoacetate, which is subsequently activated to a thioester and degraded via thiolysis. Two different types of acetone carboxylases have been described, which require either 2 or 4 ATP equivalents as an energy supply for the carboxylation reaction. Both enzymes appear to combine acetone enolphosphate with carbonic phosphate to form acetoacetate. A similar but more complex enzyme is known to carboxylate the aromatic ketone acetophenone, a metabolic intermediate in anaerobic ethylbenzene metabolism in denitrifying bacteria, with simultaneous hydrolysis of 2 ATP to 2 ADP. Obligately anaerobic sulfate-reducing bacteria activate acetone to a four-carbon compound as well, but via a different process than bicarbonate- or CO2-dependent carboxylation. The present evidence indicates that either carbon monoxide or a formyl residue is used as a cosubstrate, and that the overall ATP expenditure of this pathway is substantially lower than in the known acetone carboxylase reactions. © 2016 S. Karger AG, Basel.

The effects of inhaled acetone on place conditioning in adolescent rats.

Science.gov (United States)

Lee, Dianne E; Pai, Jennifer; Mullapudui, Uma; Alexoff, David L; Ferrieri, Richard; Dewey, Stephen L

2008-03-01

Acetone is an ubiquitous ingredient in many household products (e.g., glue solvents, air fresheners, adhesives, nail polish, and paint) that is putatively abused; however, there is little empirical evidence to suggest that acetone alone has any abuse liability. Therefore, we systematically investigated the conditioned response to inhaled acetone in a place conditioning apparatus. Three groups of male, Sprague-Dawley rats were exposed to acetone concentrations of 5000, 10,000 or 20,000 ppm for 1 h in a conditioned place preference apparatus alternating with air for 6 pairing sessions. A place preference test ensued in an acetone-free environment. To test the preference of acetone as a function of pairings sessions, the 10,000 ppm group received an additional 6 pairings and an additional group received 3 pairings. The control group received air in both compartments. Locomotor activity was recorded by infrared photocells during each pairing session. We noted a dose response relationship to acetone at levels 5000-20,000 ppm. However, there was no correlation of place preference as a function of pairing sessions at the 10,000 ppm level. Locomotor activity was markedly decreased in animals on acetone-paired days as compared to air-paired days. The acetone concentrations we tested for these experiments produced a markedly decreased locomotor activity profile that resemble CNS depressants. Furthermore, a dose response relationship was observed at these pharmacologically active concentrations, however, animals did not exhibit a positive place preference.

The effects of inhaled acetone on place conditioning in adolescent rats

Science.gov (United States)

Lee, Dianne E.; Pai, Jennifer; Mullapudui, Uma; Alexoff, David L.; Ferrieri, Richard; Dewey, Stephen L.

2009-01-01

Introduction Acetone is a ubiquitous ingredient in many household products (e.g., glue solvents, air fresheners, adhesives, nail polish, and paint) that is putatively abused; however, there is little empirical evidence to suggest that acetone alone has any abuse liability. Therefore, we systematically investigated the conditioned response to inhaled acetone in a place conditioning apparatus. Method Three groups of male, Sprague-Dawley rats were exposed to acetone concentrations of 5,000, 10,000 or 20,000 ppm for 1 hour in a conditioned place preference apparatus alternating with air for 6 pairing sessions. A place preference test ensued in an acetone-free environment. To test the preference of acetone as a function of pairings sessions, the 10,000 ppm group received an additional 6 pairings and an additional group received 3 pairings. The control group received air in both compartments. Locomotor activity was recorded by infrared photocells during each pairing session. Results We noted a dose response relationship to acetone at levels 5,000-20,000 ppm. However, there was no correlation of place preference as a function of pairing sessions at the 10,000 ppm level. Locomotor activity was markedly decreased in animals on acetone-paired days as compared to air-paired days. Conclusion The acetone concentrations we tested for these experiments produced a markedly decreased locomotor activity profile that resemble CNS depressants. Furthermore, a dose response relationship was observed at these pharmacologically active concentrations, however, animals did not exhibit a positive place preference. PMID:18096214

Chain dechlorination of organic chlorinated compounds in alcohol solutions by 60Co gamma-rays, (1)

International Nuclear Information System (INIS)

Sawai, Takeshi; Shimokawa, Toshinari; Sawai, Teruko; Hosoda, Ieji; Kondo, Masaharu.

1975-01-01

A study was made on radiolytic dechlorination of pentachlorobenzene in alkaline alcohol solutions. The dechlorination yield (G(Cl - )) was found to depend on the alcohols used as solvent and the concentrations of the chlorinated benzene and hydroxide ion. The high yields obtained in alkaline 2-propanol, sec-butanol and ethanol indicate a chain process in the dechlorination reaction. The value of G(Cl - ) was highest in 2-propanol, and the principal products generated were potassium chloride, acetone and the lower chlorinated benzenes, while a decrease was seen in the hydroxide ion concentration. The concentrations produced of potassium chloride and acetone, as well as the decrease in hydroxide ion concentration, are all roughly equal at all doses. With increasing irradiation dose, pentachlorobenzene was dechlorinated to tetra, tri, di and monochlorobenzene. 1,2,4,5-tetrachlorobenzene, 1,2,4-trichlorobenzene and 1,4-dichlorobenzene were main products. A discussion is given of the detailed mechanism of the dechlorination in alkaline alcohols and the effect of alcohols on G(Cl - ). (auth.)

Smooth isoindolinone formation from isopropyl carbamates via Bischler-Napieralski-type cyclization.

Science.gov (United States)

Adachi, Satoshi; Onozuka, Masao; Yoshida, Yuko; Ide, Mitsuaki; Saikawa, Yoko; Nakata, Masaya

2014-01-17

Isopropyl carbamates derived from benzylamines provide isoindolinones by treatment with phosphorus pentoxide at room temperature. Utility of this Bischler-Napieralski-type cyclization and a new mechanism involving a carbamoyl cation for rationalization of this smooth conversion are discussed.

[Adsorption characteristics of acetone and butanone onto honeycomb ZSM-5 molecular sieve].

Science.gov (United States)

Du, Juan; Luan, Zhi-Qiang; Xie, Qiang; Ye, Ping-Wei; Li, Kai; Wang, Xi-Qin

2013-12-01

Adsorption capacity of acetone and acetone-butanone mixture onto honeycomb ZSM-5 molecular sieve was measured in this paper, and the influences of relative humidity, initial adsorbate concentration and airflow velocity on the adsorption process were investigated. Besides, adsorption performance parameters were calculated by Wheeler's equation. The results showed that relative humidity had no obvious influence on the acetone adsorption performance, which suggests that this material has good hydrophobic ability; in the low concentration range, the dynamic saturated adsorption capacity of acetone increased with the increase of initial concentration, but in the occasion of high concentration of acetone gas (more than 9 mg x L(-1)), the dynamic saturated adsorption capacity maintained at a certain level and did not vary with the increase of initial concentration; the increase of air flow velocity resulted in significant increase of acetone adsorption rate constant, at the same time the critical layer thickness of the adsorbent bed also increased significantly. In the cases of acetone-butanone mixture, the adsorption capacity of butanone onto ZSM-5 was clearly higher than that of acetone.

2-Isopropyl-4,7-dimethyl-1-nitronaphthalene

Directory of Open Access Journals (Sweden)

Ahmed Benharref

2017-04-01

Full Text Available All the non-H atoms of the title compound, C15H17NO2, except the CH3 groups of the isopropyl unit and the O atoms of the nitro group, lie on a crystallographic mirror plane. The dihedral angle between the naphthalene plane and the nitro group is constrained to be 90° by symmetry. In the crystal, molecules are linked by π–π interactions [centroid–centroid separation = 3.6591 (4 Å] and stacked along the b-axis direction.

Purification and characterization of acetone carboxylase from Xanthobacter strain Py2

OpenAIRE

Sluis, Miriam K.; Ensign, Scott A.

1997-01-01

Acetone metabolism in the aerobic bacterium Xanthobacter strain Py2 proceeds by a carboxylation reaction forming acetoacetate as the first detectable product. In this study, acetone carboxylase, the enzyme catalyzing this reaction, has been purified to homogeneity and characterized. Acetone carboxylase was comprised of three polypeptides with molecular weights of 85,300, 78,300, and 19,600 arranged in an α2β2γ2 quaternary structure. The carboxylation of acetone was coupled to the hydrolysis o...

trans-Carbonylchloridobis(tri-p-tolylphosphinerhodium(I acetone solvate

Directory of Open Access Journals (Sweden)

Brian R. James

2008-03-01

Full Text Available The title compound, [RhCl(C21H21P2(CO]·C3H6O, was precipitated in trace yield from a reaction of RhCl(cod(THP with P(p-tol3 in a 1:1 acetone-d6/CD3OD solution under a hydrogen atmosphere [p-tol = p-tolyl, THP = tris(hydroxymethylphosphine, P(CH2OH3, and cod = 1,5-cyclooctadiene]. The complex displays a square-planar geometry around the RhI atom. The complex molecules and the acetone molecules are linked into a chain along the a axis by intermolecular C—H...Cl and C—H...O hydrogen bonds.

Acetone and Water on TiO(110): H/D Exchange

International Nuclear Information System (INIS)

Henderson, Michael A.

2005-01-01

Isotopic H/D exchange between coadsorbed acetone and water on the TiO(110) surface was examined using temperature programmed desorption (TPD) as a function of coverage and two surface pretreatments (oxidation and reduction). Coadsorbed acetone and water interact repulsively on reduced TiO(110) based on results from the companion paper to this study, with water exerting a greater influence in destabilizing acetone and acetone having only a nominal influence on water. Despite the repulsive interaction between these coadsorbates, about 0.02 ML of a 1 ML d6-acetone on the reduced surface exhibits H/D exchange with coadsorbed water, with the exchange occurring exclusively in the high temperature region of the d?-acetone TPD spectrum at ∼340 K. The effect was confirmed with combinations of d?-acetone and D?O. The extent of exchange decreased on the reduced surface with water coverages above ∼0.3 ML due to the ability of water to displace coadsorbed acetone from first layer sites to the multilayer. In contrast, the extent of exchange increased by a factor of 3 when the surface was pre-oxidized prior to coadsorption. In this case, there was no evidence for the negative influence of high water coverages on the extent of H/D exchange. Comparison of the TPD spectra from the exchange products (either d?- or d?-acetone depending on the coadsorption pairing) suggests that, in addition to the 340 K exchange process seen on the reduced surface, a second exchange process was observed on the oxidized surface at ∼390 K. In both cases (oxidized and reduced), desorption of the H/D exchange products appeared to be reaction limited and to involve the influence of OH/OD groups (or water formed during recombinative desorption of OH/OD groups) instead of molecularly adsorbed water. The 340 K exchange process is assigned to reaction at step sites and the 390 K exchange process is attributed to the influence of oxygen adatoms deposited during surface oxidation. The H/D exchange

Apparatus and method for monitoring breath acetone and diabetic diagnostics

Science.gov (United States)

Duan, Yixiang [Los Alamos, NM; Cao, Wenqing [Los Alamos, NM

2008-08-26

An apparatus and method for monitoring diabetes through breath acetone detection and quantitation employs a microplasma source in combination with a spectrometer. The microplasma source provides sufficient energy to produce excited acetone fragments from the breath gas that emit light. The emitted light is sent to the spectrometer, which generates an emission spectrum that is used to detect and quantify acetone in the breath gas.

Direct α-alkylation of ketones with alcohols in water.

Science.gov (United States)

Xu, Guoqiang; Li, Qiong; Feng, Jiange; Liu, Qiang; Zhang, Zuojun; Wang, Xicheng; Zhang, Xiaoyun; Mu, Xindong

2014-01-01

The direct α-alkylation of ketones with alcohols has emerged as a new green protocol to construct C-C bonds with H2 O as the sole byproduct. In this work, a very simple and convenient Pd/C catalytic system for the direct α-alkylation of ketones with primary alcohols in pure water is developed. Based on this catalytic system, aqueous mixtures of dilute acetone, 1-butanol, and ethanol (mimicking ABE fermentation products) can be directly transformed into C5 -C11 or longer-chain ketones and alcohols, which are precursors to fuels. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Laser-induced fluorescence imaging of acetone inside evaporating and burning fuel droplets

Science.gov (United States)

Shringi, D. S.; Shaw, B. D.; Dwyer, H. A.

2009-01-01

Laser-induced fluorescence was used to visualize acetone fields inside individual droplets of pure acetone as well as droplets composed of methanol or 1-propanol initially mixed with acetone. Droplets were supported on a horizontal wire and two vaporization conditions were investigated: (1) slow evaporation in room air and (2) droplet combustion, which leads to substantially faster droplet surface regression rates. Acetone was preferentially gasified, causing its concentration in droplets to drop in time with resultant decreases in acetone fluorescence intensities. Slowly vaporizing droplets did not exhibit large spatial variations of fluorescence within droplets, indicating that these droplets were relatively well mixed. Ignition of droplets led to significant variations in fluorescence intensities within droplets, indicating that these droplets were not well mixed. Ignited droplets composed of mixtures of 1-propanol and acetone showed large time-varying changes in shapes for higher acetone concentrations, suggesting that bubble formation was occurring in these droplets.

An engineered non-oxidative glycolysis pathway for acetone production in Escherichia coli.

Science.gov (United States)

Yang, Xiaoyan; Yuan, Qianqian; Zheng, Yangyang; Ma, Hongwu; Chen, Tao; Zhao, Xueming

2016-08-01

To find new metabolic engineering strategies to improve the yield of acetone in Escherichia coli. Results of flux balance analysis from a modified Escherichia coli genome-scale metabolic network suggested that the introduction of a non-oxidative glycolysis (NOG) pathway would improve the theoretical acetone yield from 1 to 1.5 mol acetone/mol glucose. By inserting the fxpk gene encoding phosphoketolase from Bifidobacterium adolescentis into the genome, we constructed a NOG pathway in E.coli. The resulting strain produced 47 mM acetone from glucose under aerobic conditions in shake-flasks. The yield of acetone was improved from 0.38 to 0.47 mol acetone/mol glucose which is a significant over the parent strain. Guided by computational analysis of metabolic networks, we introduced a NOG pathway into E. coli and increased the yield of acetone, which demonstrates the importance of modeling analysis for the novel metabolic engineering strategies.

Acetone production with metabolically engineered strains of Acetobacterium woodii.

Science.gov (United States)

Hoffmeister, Sabrina; Gerdom, Marzena; Bengelsdorf, Frank R; Linder, Sonja; Flüchter, Sebastian; Öztürk, Hatice; Blümke, Wilfried; May, Antje; Fischer, Ralf-Jörg; Bahl, Hubert; Dürre, Peter

2016-07-01

Expected depletion of oil and fossil resources urges the development of new alternative routes for the production of bulk chemicals and fuels beyond petroleum resources. In this study, the clostridial acetone pathway was used for the formation of acetone in the acetogenic bacterium Acetobacterium woodii. The acetone production operon (APO) containing the genes thlA (encoding thiolase A), ctfA/ctfB (encoding CoA transferase), and adc (encoding acetoacetate decarboxylase) from Clostridium acetobutylicum were cloned under the control of the thlA promoter into four vectors having different replicons for Gram-positives (pIP404, pBP1, pCB102, and pCD6). Stable replication was observed for all constructs. A. woodii [pJIR_actthlA] achieved the maximal acetone concentration under autotrophic conditions (15.2±3.4mM). Promoter sequences of the genes ackA from A. woodii and pta-ack from C. ljungdahlii were determined by primer extension (PEX) and cloned upstream of the APO. The highest acetone production in recombinant A. woodii cells was achieved using the promoters PthlA and Ppta-ack. Batch fermentations using A. woodii [pMTL84151_actthlA] in a bioreactor revealed that acetate concentration had an effect on the acetone production, due to the high Km value of the CoA transferase. In order to establish consistent acetate concentration within the bioreactor and to increase biomass, a continuous fermentation process for A. woodii was developed. Thus, acetone productivity of the strain A. woodii [pMTL84151_actthlA] was increased from 1.2mgL(-1)h(-1) in bottle fermentation to 26.4mgL(-1)h(-1) in continuous gas fermentation. Copyright © 2016 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

Breath acetone monitoring by portable Si:WO3 gas sensors

International Nuclear Information System (INIS)

Righettoni, Marco; Tricoli, Antonio; Gass, Samuel; Schmid, Alex; Amann, Anton; Pratsinis, Sotiris E.

2012-01-01

Highlights: ► Portable sensors were developed and tested for monitoring acetone in the human breath. ► Acetone concentrations down to 20 ppb were measured with short response times ( 3 nanostructured films was developed. The chamber volume was miniaturized while reaction-limited and transport-limited gas flow rates were identified and sensing temperatures were optimized resulting in a low detection limit of acetone (∼20 ppb) with short response (10–15 s) and recovery times (35–70 s). Furthermore, the sensor signal (response) was robust against variations of the exhaled breath flow rate facilitating application of these sensors at realistic relative humidities (80–90%) as in the human breath. The acetone content in the breath of test persons was monitored continuously and compared to that of state-of-the-art proton transfer reaction mass spectrometry (PTR-MS). Such portable devices can accurately track breath acetone concentration to become an alternative to more elaborate breath analysis techniques.

Quantitative Clinical Diagnostic Analysis of Acetone in Human Blood by HPLC: A Metabolomic Search for Acetone as Indicator

OpenAIRE

Akgul Kalkan, Esin; Sahiner, Mehtap; Ulker Cakir, Dilek; Alpaslan, Duygu; Yilmaz, Selehattin

2016-01-01

Using high-performance liquid chromatography (HPLC) and 2,4-dinitrophenylhydrazine (2,4-DNPH) as a derivatizing reagent, an analytical method was developed for the quantitative determination of acetone in human blood. The determination was carried out at 365?nm using an ultraviolet-visible (UV-Vis) diode array detector (DAD). For acetone as its 2,4-dinitrophenylhydrazone derivative, a good separation was achieved with a ThermoAcclaim C18 column (15?cm ? 4.6?mm ? 3??m) at retention time (t R) ...

A cross-sectional study of breath acetone based on diabetic metabolic disorders.

Science.gov (United States)

Li, Wenwen; Liu, Yong; Lu, Xiaoyong; Huang, Yanping; Liu, Yu; Cheng, Shouquan; Duan, Yixiang

2015-02-26

Breath acetone is a known biomarker for diabetes mellitus in breath analysis. In this work, a cross-sectional study of breath acetone based on clinical metabolic disorders of type 2 diabetes mellitus (T2DM) was carried out. Breath acetone concentrations of 113 T2DM patients and 56 apparently healthy individuals were measured at a single time point. Concentrations varied from 0.22 to 9.41 ppmv (mean 1.75 ppmv) for T2DM, which were significantly higher than those for normal controls (ranged from 0.32 to 1.96 ppmv, mean 0.72 ppmv, p = 0.008). Observations in our work revealed that breath acetone concentrations elevated to different degrees, along with the abnormality of blood glucose, glycated hemoglobin (HbA1c), triglyceride and cholesterol. Breath acetone showed obviously positive correlations with blood ketone and urine ketone. Possible metabolic relations between breath acetone and diabetic disorders were also discussed. This work aimed at giving an overall assessment of breath acetone from the perspective of clinical parameters for type 2 diabetes.

Synthesis of carbon-13 labeled ibuprofen

International Nuclear Information System (INIS)

Hsi, R.S.P.; Stelzer, L.S.; Stolle, W.T.

1989-01-01

This report describes the synthesis of 2-[4-(2-methyl)propyl-phenyl]propionic acid (ibuprofen) labeled with carbon-13 either at the terminal methyl carbons, or at the methine carbon of the isobutyl side chain. The synthetic route involves the removal of the isopropyl group in the isobutyl side-chain of ibuprofen via 2-[4-(2-methyl-1-propenyl)phenyl]propionic acid, followed by restoration of the isopropyl group with a Wittig reaction, using appropriate carbon-13 labeled acetone as the precursor of the isopropyl group. Interesting NMR coupling data attributable to phosphorous and carbon-13 are presented in the experimental section. (author)

Brain perfusion image using N-isopropyl-p-[123I] iodoamphetamine

International Nuclear Information System (INIS)

Matsuda, Hiroshi; Seki, Hiroyasu; Ishida, Hiroko

1984-01-01

In brain perfusion images using N-Isopropyl-p-[ 123 I] Iodoamphetamine and rotating gamma camera emission computed tomography, brain maps showing laterality indices (LI) were made for the purpose of detecting ineterhemispheric differences. Left (L) and right (R) leteral images were made by adding sagittal section images in each hemisphere, respectively. LI was calculated as follows. LI=100(1+(R-L)/(R+L)). The normal ranges (mean+-2 s.d.) of the indices determined by those obtained in five normal right-handed subjects were 103+-4 and 103+-10 for brain mean and each pixel, respectively. Out of 25 measurements in 22 righthanded patients with cerebrovascular accidents, brain mean LI beyond the normal limits and areas showing abnormal regional LI were observed in 5 (20%) and 21 (84%) measurements, respectively. On the other hand, X-ray CT showed low density areas in only 12 (48%). These brain maps were clinically useful for detecting and quantifying interhemispheric differences in brain perfusion images with N-Isopropyl-p-[ 123 I] Iodoamphetamine. (author)

Zeolites as alcohol adsorbents from aqueous solutions

Directory of Open Access Journals (Sweden)

Cekova Blagica

2006-01-01

Full Text Available The potential usage of zeolites as adsorbents for the removal of organic molecules from water was investigated in a series of experiments with aqueous solutions of lower alcohols. This could represent a simple solution to the problem of cleaning up industrial wastewater as well as recovering valuable chemicals at relatively low costs. Adsorption isotherms of the Langmuir type were applied, and calculations showed that the amount of propanol adsorbed on silicalite corresponded to approximately 70% of the pore volume. The adsorption process is simple, and recovery of the more concentrated products is easily done by heat treatment and/or at lowered pressures. Adsorption experiments with aqueous acetone showed that silicalite had approximately the same adsorption capacity for acetone as for n-propanol. Heats of adsorption were determined calorimetrically.

Proteomic analysis of nitrate-dependent acetone degradation by Alicycliphilus denitrificans strain BC

NARCIS (Netherlands)

Oosterkamp, M.J.; Boeren, S.; Atashgahi, S.; Plugge, C.M.; Schaap, P.J.; Stams, A.J.M.

2015-01-01

Alicycliphilus denitrificans strain BC grows anaerobically on acetone with nitrate as electron acceptor. Comparative proteomics of cultures of A. denitrificans strain BC grown on either acetone or acetate with nitrate was performed to study the enzymes involved in the acetone degradation pathway. In

Catalytic function of the mycobacterial binuclear iron monooxygenase in acetone metabolism.

Science.gov (United States)

Furuya, Toshiki; Nakao, Tomomi; Kino, Kuniki

2015-10-01

Mycobacteria such as Mycobacterium smegmatis strain mc(2)155 and Mycobacterium goodii strain 12523 are able to grow on acetone and use it as a source of carbon and energy. We previously demonstrated by gene deletion analysis that the mimABCD gene cluster, which encodes a binuclear iron monooxygenase, plays an essential role in acetone metabolism in these mycobacteria. In the present study, we determined the catalytic function of MimABCD in acetone metabolism. Whole-cell assays were performed using Escherichia coli cells expressing the MimABCD complex. When the recombinant E. coli cells were incubated with acetone, a product was detected by gas chromatography (GC) analysis. Based on the retention time and the gas chromatography-mass spectrometry (GC-MS) spectrum, the reaction product was identified as acetol (hydroxyacetone). The recombinant E. coli cells produced 1.02 mM of acetol from acetone within 24 h. Furthermore, we demonstrated that MimABCD also was able to convert methylethylketone (2-butanone) to 1-hydroxy-2-butanone. Although it has long been known that microorganisms such as mycobacteria metabolize acetone via acetol, this study provides the first biochemical evidence for the existence of a microbial enzyme that catalyses the conversion of acetone to acetol. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Adsorption and Reaction of Acetone over CeOX(111) Thin Films

International Nuclear Information System (INIS)

Mullins, David R.; Senanayake, Sanjaya D.; Gordon, Wesley O.; Overbury, Steven H.

2009-01-01

This study reports the interaction of acetone (CH3COCH3), the simplest ketone, with well ordered CeO2(111) thin film surfaces. The fully oxidized CeO2(111) surface shows a weak interaction with acetone with the sole desorption product (TPD) being acetone at 210 K. The chemisorbed molecule binds to the surface as the ?1-acetone species rather than through a bridge-bonded dioxy-configuration. Exposure of a CeO2(111) surface to acetone at 600K removes oxygen as CO and results in the conversion of Ce4+ to Ce3+. Acetone chemisorbs strongly on reduced CeO2-x(111) with molecular acetone desorbing near 500 K. Decomposition also occurs with H2 desorbing between 450 and 600 K and C reacting with O in the ceria to desorb above 650 K. A stable species exists from 200 to 500 K on the reduced surface that has three unique types of C. High resolution C 1s XPS spectra indicate these are Ce-CH2, C-CH3 and C-O species. C k-edge NEXAFS indicates the presence of C(double b ond)C and C(double b ond)O bonds. It is postulated that the intermediate is a carbanion bonded through both O and C atoms to Ce cations.

Delayed fluorescence of meso-tetraphenylporphyrin in acetone and in dimethylsulphoxide

International Nuclear Information System (INIS)

Korinek, M.; Klinger, P.; Dedic, R.; Psencik, J.; Svoboda, A.; Hala, J.

2007-01-01

Photodynamic therapy is based on photosensitisation of singlet oxygen by porphyrin-like molecules. We have performed a systematic study of delayed fluorescence of tetraphenylporphyrin in acetone (used as a spectroscopic standard) and in dimethylsulphoxide (clinically used solvent) to obtain spectra, kinetics, and quantum yields, including their dependencies on tetraphenylporphyrin concentration. In dimethylsulphoxide the repopulation of excited singlets and subsequent delayed fluorescence is caused by triplet-triplet quenching with rate constant of (2.2±1.0)x10 9 l mol -1 s -1 . However, repopulation of excited singlets in acetone is also caused by singlet oxygen reaction with triplet tetraphenylporphyrin causing monoexponential delayed fluorescence decay with the lifetime 0.3 μs. Due to much lower viscosity of acetone compared to dimethylsulphoxide, triplet-triplet quenching constant in acetone is much higher (1.7±0.7)x10 10 l mol -1 s -1 . The rate constant for the reaction of singlet oxygen with triplet of tetraphenylporphyrin is (2.0±0.8)x10 10 l mol -1 s -1 in acetone

Characterisation of cellulose films regenerated from acetone/water coagulants.

Science.gov (United States)

Geng, Hongjuan; Yuan, Zaiwu; Fan, Qingrui; Dai, Xiaonan; Zhao, Yue; Wang, Zhaojiang; Qin, Menghua

2014-02-15

A precooled aqueous solution of 7 wt% NaOH/12 wt% urea was used to dissolve cellulose up to a concentration of 2 wt%, which was then coagulated in an acetone/water mixture to regenerate cellulose film. The volume ratio of acetone to water (φ) had a dominant influence on film dimensional stability, film-forming ability, micromorphology, and mechanical strength. The film regenerated at φ=2.0 showed excellent performance in both dimensional stability and film-forming ability. Compared to that from pure acetone, the cellulose film from the acetone/water mixture with φ=2.0 was more densely interwoven, since the cellulosic fibrils formed during regeneration had pores with smaller average diameter. The alkali capsulated in the film during film formation could be released at quite a slow rate into the surrounding aqueous solution. The regenerated cellulose film with adjustable structure and properties may have potential applications in drug release and ultra filtration. Copyright © 2013 Elsevier Ltd. All rights reserved.

Novel Acetone Metabolism in a Propane-Utilizing Bacterium, Gordonia sp. Strain TY-5▿

Science.gov (United States)

Kotani, Tetsuya; Yurimoto, Hiroya; Kato, Nobuo; Sakai, Yasuyoshi

2007-01-01

In the propane-utilizing bacterium Gordonia sp. strain TY-5, propane was shown to be oxidized to 2-propanol and then further oxidized to acetone. In this study, the subsequent metabolism of acetone was studied. Acetone-induced proteins were found in extracts of cells induced by acetone, and a gene cluster designated acmAB was cloned on the basis of the N-terminal amino acid sequences of acetone-induced proteins. The acmA and acmB genes encode a Baeyer-Villiger monooxygenase (BVMO) and esterase, respectively. The BVMO encoded by acmA was purified from acetone-induced cells of Gordonia sp. strain TY-5 and characterized. The BVMO exhibited NADPH-dependent oxidation activity for linear ketones (C3 to C10) and cyclic ketones (C4 to C8). Escherichia coli expressing the acmA gene oxidized acetone to methyl acetate, and E. coli expressing the acmB gene hydrolyzed methyl acetate. Northern blot analyses revealed that polycistronic transcription of the acmAB gene cluster was induced by propane, 2-propanol, and acetone. These results indicate that the acmAB gene products play an important role in the metabolism of acetone derived from propane oxidation and clarify the propane metabolism pathway of strain TY-5 (propane → 2-propanol → acetone → methyl acetate → acetic acid + methanol). This paper provides the first evidence for BVMO-dependent acetone metabolism. PMID:17071761

Protein precipitation of diluted samples in SDS-containing buffer with acetone leads to higher protein recovery and reproducibility in comparison with TCA/acetone approach.

Science.gov (United States)

Santa, Cátia; Anjo, Sandra I; Manadas, Bruno

2016-07-01

Proteomic approaches are extremely valuable in many fields of research, where mass spectrometry methods have gained an increasing interest, especially because of the ability to perform quantitative analysis. Nonetheless, sample preparation prior to mass spectrometry analysis is of the utmost importance. In this work, two protein precipitation approaches, widely used for cleaning and concentrating protein samples, were tested and compared in very diluted samples solubilized in a strong buffer (containing SDS). The amount of protein recovered after acetone and TCA/acetone precipitation was assessed, as well as the protein identification and relative quantification by SWATH-MS yields were compared with the results from the same sample without precipitation. From this study, it was possible to conclude that in the case of diluted samples in denaturing buffers, the use of cold acetone as precipitation protocol is more favourable than the use of TCA/acetone in terms of reproducibility in protein recovery and number of identified and quantified proteins. Furthermore, the reproducibility in relative quantification of the proteins is even higher in samples precipitated with acetone compared with the original sample. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Extracting oils

Energy Technology Data Exchange (ETDEWEB)

Patart, G

1926-03-15

In the hydrogenation or extraction of by-products from organic substances at high temperatures and pressures, the gases or liquids, or both, used are those which are already heated and compressed during industrial operations such as exothermic synthesizing reactions such as the production of methanol from hydrogen and carbon monoxide in a catalytic process. Gases from this reaction may be passed upwardly through a digester packed with pine wood while liquid from the same catalytic process is passed downwardly through the material. The issuing liquid contains methanol, pine oil, acetone, isopropyl alcohol, and acetic acid. The gases contain additional hydrogen, carbon monoxide, methane, ethylene, and its homologs which are condensed upon the catalyser to liquid hydrocarbons. Petroleum oils and coal may be treated similarly.

Monitoring the Aggregation of Dansyl Chloride in Acetone through Fluorescence Measurements

Institute of Scientific and Technical Information of China (English)

FANG，Yu; YIN，Yi－Qing; 等

2002-01-01

The aggregation of dansyl chloride (DNS-Cl) in acetone has been studied in detail by steady-state fluorescence techniques.It has been demonstrated that DNS-Cl is stable in acetone during purification and aggregation study processes.The aggregates are not solvolyzed in acetone,and do not take part n any chemical reactions either.It has been found that DNS-Cl tends to aggregate even when its concentration is much lower than its solubility in acetone.The aggregation is reversible,and both the aggregation and the deaggregation are very slow processes.Introduction of SDS has a positive effect upon the formation and stabilization of the aggregates.

Monitoring the Aggregation of Dansyl Chloride in Acetone through Fluorescence Measurements

Institute of Scientific and Technical Information of China (English)

FANG,Yu(房喻); YIN,Yi-Qing(尹艺青); HU,Dao-Dao(胡道道); GAO,Gai-Ling(高改玲)

2002-01-01

The aggregation of dansyl chloride (DNS-Cl) in acetone has been studied in detail by steady-state fluorescence techniques. It has been demonstrated that DNS-Cl is stable in acetone during purification and aggregation study processes. The aggregates are not solvolyzed in acetone, and do not take part in any chemical reactions either. It has been found that DNS-Cl tends to aggregate even when its concentration is much lower than its solubility in acetone. The aggregation is reversible, and both the aggregation and the deaggregation are very slow processes.Introduction of SDS has a positive effect upon the formation and stabilization of the aggregates.

Antibacterial Activities and Mechanism of Action of Acetone Extracts from Rabdosia rubescens

Directory of Open Access Journals (Sweden)

Li Ping Cheng

2014-12-01

Full Text Available The antibacterial activities and mechanism of action of acetone extracts from R. rubescens were reported in this paper. The results showed that 80% acetone extracts had both the highest contents of total phenolics and flavonoids. Acetone extracts showed better antibacterial activities against Gram-positive bacterial strains and there were no inhibitory effects found on tested Gram-negative bacteria. In addition, 80% acetone extracts from R. rubescens had relatively higher antibacterial activities with the lowest values of MIC and MBC at 2.5 mg/mL and 5 mg/mL against B. subtilis. The antibacterial mechanism of 80% acetone extracts against Bacillus subtilis might be described as disrupting cell wall, increasing cell membrane permeability, and finally leading to the leakage of cell constituents

Sensor gas analyzer for acetone determination in expired air

Science.gov (United States)

Baranov, Vitaly V.

2001-05-01

Diseases and changes in the way of life change the concentration and composition of the expired air. Our adaptable gas analyzer is intended for the selective analysis of expired air and can be adapted for the solution of current diagnostic and analytical tasks by the user (a physician or a patient). Having analyzed the existing trends in the development of noninvasive diagnostics we have chosen the method of noninvasive acetone detection in expired air, where the acetone concentration correlates with blood and urine glucose concentrations. The appearance of acetone in expired air is indicative of disorders that may be caused not only by diabetes but also be wrong diet, incorrect sportsmen training etc. To control the disorders one should know the acetone concentration in the human body. This knowledge allows one to judge upon the state of the patient, choose a correct diet that will not cause damage to the patient's health, determine sportsmen training efficiency and results and solve the artificial pancreas problem. Our device provide highly accurate analysis, rapid diagnostics and authentic acetone quantification in the patient's body at any time aimed at prediction of the patient's state and assessing the efficiency of the therapy used. Clinical implementation of the device will improve the health and save lives of many thousands of diabetes sufferers.

IR spectra and properties of solid acetone, an interstellar and cometary molecule

Science.gov (United States)

Hudson, Reggie L.; Gerakines, Perry A.; Ferrante, Robert F.

2018-03-01

Mid-infrared spectra of amorphous and crystalline acetone are presented along with measurements of the refractive index and density for both forms of the compound. Infrared band strengths are reported for the first time for amorphous and crystalline acetone, along with IR optical constants. Vapor pressures and a sublimation enthalpy for crystalline acetone also are reported. Positions of 13C-labeled acetone are measured. Band strengths are compared to gas-phase values and to the results of a density-functional calculation. A 73% error in previous work is identified and corrected.

Effect of linear alcohol molecular size on the self-assembly of fullerene whiskers

International Nuclear Information System (INIS)

Amer, Maher S.; Todd, T. Kyle; Busbee, John D.

2011-01-01

Highlights: → The longer the alcohol molecule, the shorter the length of the assembled whisker. → Interaction between alcohol and fullerene solvent is the key factor. → The stronger the alcohol/solvent interaction, the longer the whisker. - Abstract: The recent development of self-assembled fullerene whiskers and wires has created an enormous potential and resolved a serious challenge for utilizing such unique class of carbon material in advanced nano-scale, molecular-based electronic, optical, and thermal devices. In this paper we investigate, the self-assembly of C 60 molecules into one-dimensional whiskers using a series of linear alcohols H(CH 2 ) n OH, with n changing from 1 (methanol) to 3 (isopropyl alcohol), to elucidate the effect of alcohol molecular size on the size distribution of the self-assemble fullerene whiskers. Our results show that the length of the produced fullerene whiskers is affected by the molecular size of the alcohol used in the process. The crucial role played by solvent/alcohol interaction in the assembly process is discussed. In addition, Raman spectroscopy measurements support the notion that the self-assembled whiskers are primarily held by depletion forces and no evidence of fullerene polymerization was observed.

Theoretical Kinetic Study of the Unimolecular Keto–Enol Tautomerism Propen-2-ol ↔ Acetone. Pressure Effects and Implications in the Pyrolysis of tert- and 2-Butanol

KAUST Repository

Grajales Gonzalez, Edwing

2018-03-21

The need for renewable and cleaner sources of energy has made biofuels an interesting alternative to fossil fuels, especially in the case of butanol isomers, with its favorable blend properties and low hygroscopicity. Although C4 alcohols are prospective fuels, some key reactions governing their pyrolysis and combustion have not been adequately studied, leading to incomplete kinetic models. Enols are important intermediates in the combustion of C4 alcohols, as well as in atmospheric processes. Butanol reactions kinetics is poorly understood. Specifically, the unimolecular tautomerism of propen-2-ol ↔ acetone, which is included in butanol combustion kinetic models, is assigned rate parameters based on the tautomerism vinyl alcohol ↔ acetaldehyde as an analogy. In an attempt to update current kinetic models for tert- and 2-butanol, a theoretical kinetic study of the titled reaction was carried out by means of CCSD(T,FULL)/aug-cc-pVTZ//CCSD(T)/6-31+G(d,p) ab initio calculations, with multistructural torsional anharmonicity and variational transition state theory considerations in a wide temperature and pressure range (200-3000 K; 0.1-108 kPa). Results differ from vinyl alcohol ↔ acetaldehyde analogue reaction, which shows lower rate constant values. It was observed that decreasing pressure leads to a decrease in rate constants, describing the expected falloff behavior. Tunneling turned out to be important, especially at low temperatures. Accordingly, pyrolysis simulations in a batch reactor for tert- and 2-butanol with computed rate constants showed important differences in comparison with previous results, such as larger acetone yield and quicker propen-2-ol consumption.

Theoretical Kinetic Study of the Unimolecular Keto–Enol Tautomerism Propen-2-ol ↔ Acetone. Pressure Effects and Implications in the Pyrolysis of tert- and 2-Butanol

KAUST Repository

Grajales Gonzalez, Edwing Javier; Monge Palacios, Manuel; Sarathy, Mani

2018-01-01

The need for renewable and cleaner sources of energy has made biofuels an interesting alternative to fossil fuels, especially in the case of butanol isomers, with its favorable blend properties and low hygroscopicity. Although C4 alcohols are prospective fuels, some key reactions governing their pyrolysis and combustion have not been adequately studied, leading to incomplete kinetic models. Enols are important intermediates in the combustion of C4 alcohols, as well as in atmospheric processes. Butanol reactions kinetics is poorly understood. Specifically, the unimolecular tautomerism of propen-2-ol ↔ acetone, which is included in butanol combustion kinetic models, is assigned rate parameters based on the tautomerism vinyl alcohol ↔ acetaldehyde as an analogy. In an attempt to update current kinetic models for tert- and 2-butanol, a theoretical kinetic study of the titled reaction was carried out by means of CCSD(T,FULL)/aug-cc-pVTZ//CCSD(T)/6-31+G(d,p) ab initio calculations, with multistructural torsional anharmonicity and variational transition state theory considerations in a wide temperature and pressure range (200-3000 K; 0.1-108 kPa). Results differ from vinyl alcohol ↔ acetaldehyde analogue reaction, which shows lower rate constant values. It was observed that decreasing pressure leads to a decrease in rate constants, describing the expected falloff behavior. Tunneling turned out to be important, especially at low temperatures. Accordingly, pyrolysis simulations in a batch reactor for tert- and 2-butanol with computed rate constants showed important differences in comparison with previous results, such as larger acetone yield and quicker propen-2-ol consumption.

Thallium-201 diethyldithiocarbamate: an alternative to iodine-123 N-isopropyl-p-iodoamphetamine

NARCIS (Netherlands)

de Bruine, J. F.; van Royen, E. A.; Vyth, A.; de Jong, J. M.; van der Schoot, J. B.

1985-01-01

The study of cerebral blood flow by single photon emission computed tomography (SPECT) requires lipophilic radiopharmaceuticals. The high cost and limited availability of N-isopropyl-p-[I-123]-iodoamphetamine ( [123I]IMP) led us to search for alternatives. Following our recent development of

Heat transfer performance of a pulsating heat pipe charged with acetone-based mixtures

Science.gov (United States)

Wang, Wenqing; Cui, Xiaoyu; Zhu, Yue

2017-06-01

Pulsating heat pipes (PHPs) are used as high efficiency heat exchangers, and the selection of working fluids in PHPs has a great impact on the heat transfer performance. This study investigates the thermal resistance characteristics of the PHP charged with acetone-based binary mixtures, where deionized water, methanol and ethanol were added to and mixed with acetone, respectively. The volume mixing ratios were 2:1, 4:1 and 7:1, and the heating power ranged from 10 to 100 W with filling ratios of 45, 55, 62 and 70%. At a low filling ratio (45%), the zeotropic characteristics of the binary mixtures have an influence on the heat transfer performance of the PHP. Adding water, which has a substantially different boiling point compared with that of acetone, can significantly improve the anti-dry-out ability inside the PHP. At a medium filling ratio (55%), the heat transfer performance of the PHP is affected by both phase transition characteristics and physical properties of working fluids. At high heating power, the thermal resistance of the PHP with acetone-water mixture is between that with pure acetone and pure water, whereas the thermal resistance of the PHP with acetone-methanol and acetone-ethanol mixtures at mixing ratios of 2:1 and 4:1 is less than that with the corresponding pure fluids. At high filling ratios (62 and 70%), the heat transfer performance of the PHP is mainly determined by the properties of working fluids that affects the flow resistance. Thus, the PHP with acetone-methanol and acetone-ethanol mixtures that have a lower flow resistance shows better heat transfer performance than that with acetone-water mixture.

Extraction of hafnium by 1-phenyl-3-methyl-4-benzoyl-5-pyralozone from aqueous-alcoholic solutions

International Nuclear Information System (INIS)

Hala, J.; Prihoda, J.

1975-01-01

Extraction of hafnium by 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (HL) in benzene, toluene, chloroform and tetrachloromethane from aqueous-alcoholic solutions of the formal acidity of 2M-HClO 4 was studied. Methyl, ethyl, n- and isopropyl, tert-butyl and allyl alcohol as well as ethylene glycol monomethyl ether and propylene glycol were used as organic components of the mixed aqueous-organic phase. Their presence in some cases resulted in a synergic increase in the distribution ratio of hafnium. The increase is interpreted using the results of a slope analysis and measurements of the alcohol distribution and the relative permittivity of the organic phase. It is suggested that HfL 4 molecules were solvated by alcohol molecules in the organic phase. At high alcohol concentration synergism changed into antagonism. This was caused by changes in the distribution of HL and its interaction with the alcohol in the organic phase. (author)

Pathological effects of acetone cyanohydrin in swiss rats

Directory of Open Access Journals (Sweden)

Marcos Natal Rufino

Full Text Available ABSTRACT Cassava has been widely used for animal and human nutrition. It has also been demonstrated to have antineoplastic and anthelmintic properties. Toxicity due to cassava consumption has been reported in ruminants and laboratory animals; therefore, this study aimed to investigate the toxic effects of acetone cyanohydrin, a metabolite of linamarin that is present in cassava, in Wistar rats. Six groups of five animals each were used to evaluate the toxic effects of acetone cyanohydrin administered at 25 (G1, 50 (G2, 75 (G3, 100 (G4 and 125 (G5 µmol/kg as a single oral dose. The control group received acidified water (pH 3.5. The animals were monitored after administration of acetone cyanohydrin, and clinical symptoms were recorded. Serum enzyme levels were measured to assess the kidney and liver function. During necropsy, tissue samples were collected for histopathological examination. After administration, some animals in the G2, G4, and G5 groups presented neurological symptoms such as convulsions, involuntary muscle contraction, staggering gait, motor coordination disability, prostration, and mydriasis. All of the animals in the G5 and four animals in the G4 group died seven minutes after the administration of acetone cyanohydrin. Animals in the other groups, particularly in G2, recovered from the acute phase. Biochemical analysis revealed hepatic lesions and liver dysfunction. Histopathology revealed severe lesions in both the liver and brain. In conclusion, acetone cyanohydrin has toxic effects in the liver, lung, and central nervous system in rats; however, at concentrations up to 25 µmol/kg, the animals could survive the acute phase.

Evidence for an Inducible Nucleotide-Dependent Acetone Carboxylase in Rhodococcus rhodochrous B276

OpenAIRE

Clark, Daniel D.; Ensign, Scott A.

1999-01-01

The metabolism of acetone was investigated in the actinomycete Rhodococcus rhodochrous (formerly Nocardia corallina) B276. Suspensions of acetone- and isopropanol-grown R. rhodochrous readily metabolized acetone. In contrast, R. rhodochrous cells cultured with glucose as the carbon source lacked the ability to metabolize acetone at the onset of the assay but gained the ability to do so in a time-dependent fashion. Chloramphenicol and rifampin prevented the time-dependent increase in this acti...

Phase transitions of amorphous solid acetone in confined geometry investigated by reflection absorption infrared spectroscopy.

Science.gov (United States)

Shin, Sunghwan; Kang, Hani; Kim, Jun Soo; Kang, Heon

2014-11-26

We investigated the phase transformations of amorphous solid acetone under confined geometry by preparing acetone films trapped in amorphous solid water (ASW) or CCl4. Reflection absorption infrared spectroscopy (RAIRS) and temperature-programmed desorption (TPD) were used to monitor the phase changes of the acetone sample with increasing temperature. An acetone film trapped in ASW shows an abrupt change in the RAIRS features of the acetone vibrational bands during heating from 80 to 100 K, which indicates the transformation of amorphous solid acetone to a molecularly aligned crystalline phase. Further heating of the sample to 140 K produces an isotropic solid phase, and eventually a fluid phase near 157 K, at which the acetone sample is probably trapped in a pressurized, superheated condition inside the ASW matrix. Inside a CCl4 matrix, amorphous solid acetone crystallizes into a different, isotropic structure at ca. 90 K. We propose that the molecularly aligned crystalline phase formed in ASW is created by heterogeneous nucleation at the acetone-water interface, with resultant crystal growth, whereas the isotropic crystalline phase in CCl4 is formed by homogeneous crystal growth starting from the bulk region of the acetone sample.

(RS-Efonidipine acetone hemisolvate

Directory of Open Access Journals (Sweden)

Yu-Heng Liu

2016-09-01

Full Text Available The asymmetric unit of the title compound, C34H38N3O7P·0.5C3H6O {systematic name: (RS-2-[phenyl(phenylmethylamino]ethyl 5-(5,5-dimethyl-2-oxo-1,3-dioxa-2λ5-phosphacyclohex-2-yl-2,6-dimethyl-4-(3-nitrophenyl-1,4-dihydropyridine-3-carboxylate acetone hemisolvate}, contains one R-efonidipine molecule, one S-efonidipine molecule and half of a solvate acetone molecule. In both efonidipine molecules, the six-membered rings of the dioxaphosphinanyl moieties display a chair conformation and the dihydropyridine rings display a flattened boat conformation. In the crystal, N—H...O, C—H...O hydrogen bonds and weak C—H...π interactions link the molecules into a three-dimensional supramolecular structure. A solvent-accessible void of 199 Å3 is found in the structure; the contribution of the heavily disordered solvate molecule was suppressed by use of the SQUEEZE routine in PLATON [Spek (2015. Acta Cryst. C71, 9–18].

Solvent (acetone-butanol: ab) production

Science.gov (United States)

This article describes production of butanol [acetone-butanol-ethanol, (also called AB or ABE or solvent)] by fermentation using both traditional and current technologies. AB production from agricultural commodities, such as corn and molasses, was an important historical fermentation. Unfortunately,...

Human sensory response to acetone/air mixtures.

Science.gov (United States)

Salthammer, T; Schulz, N; Stolte, R; Uhde, E

2016-10-01

The release of organic compounds from building products may influence the perceived air quality in the indoor environment. Consequently, building products are assessed for chemical emissions and for the acceptability of emitted odors. A procedure for odor evaluations in test chambers is described by the standard ISO 16000-28. A panel of eight or more trained subjects directly determines the perceived intensity Π (unit pi) of an air sample via diffusers. For the training of the panelists, a comparative Π-scale is applied. The panelists can use acetone/air mixtures in a concentration range between 20 mg/m(3) (0 pi) and 320 mg/m(3) (15 pi) as reference. However, the training and calibration procedure itself can substantially contribute to the method uncertainty. This concerns the assumed odor threshold of acetone, the variability of panelist responses, and the analytical determination of acetone concentrations in air with online methods as well as the influence of the diffuser geometry and the airflow profile. © 2015 The Authors. Indoor Air published by John Wiley & Sons Ltd.

On the adsorption/reaction of acetone on pure and sulfate-modified zirconias.

Science.gov (United States)

Crocellà, Valentina; Cerrato, Giuseppina; Morterra, Claudio

2013-08-28

In situ FTIR spectroscopy was employed to investigate some aspects of the ambient temperature (actually, IR-beam temperature) adsorption of acetone on various pure and sulfate-doped zirconia specimens. Acetone uptake yields, on all examined systems and to a variable extent, different types of specific molecular adsorption, depending on the kind/population of available surface sites: relatively weak H-bonding interaction(s) with surface hydroxyls, medium-strong coordinative interaction with Lewis acidic sites, and strong H-bonding interaction with Brønsted acidic centres. Moreover acetone, readily and abundantly adsorbed in molecular form, is able to undergo the aldol condensation reaction (yielding, as the main reaction product, adsorbed mesityl oxide) only if the adsorbing material possesses some specific surface features. The occurrence/non-occurrence of the acetone self-condensation reaction is discussed, and leads to conclusions concerning the sites that catalyze the condensation reaction that do not agree with either of two conflicting interpretations present in the literature of acetone uptake/reaction on, mainly, zeolitic systems. In particular, what turns out to be actually necessary for the acetone aldol condensation reaction to occur on the examined zirconia systems is the presence of coordinatively unsaturated O(2-) surface sites of basicity sufficient to lead to the extraction of a proton from one of the CH3 groups of adsorbed acetone.

Breath acetone monitoring by portable Si:WO3 gas sensors

Science.gov (United States)

Righettoni, Marco; Tricoli, Antonio; Gass, Samuel; Schmid, Alex; Amann, Anton; Pratsinis, Sotiris E.

2013-01-01

Breath analysis has the potential for early stage detection and monitoring of illnesses to drastically reduce the corresponding medical diagnostic costs and improve the quality of life of patients suffering from chronic illnesses. In particular, the detection of acetone in the human breath is promising for non-invasive diagnosis and painless monitoring of diabetes (no finger pricking). Here, a portable acetone sensor consisting of flame-deposited and in situ annealed, Si-doped epsilon-WO3 nanostructured films was developed. The chamber volume was miniaturized while reaction-limited and transport-limited gas flow rates were identified and sensing temperatures were optimized resulting in a low detection limit of acetone (~20 ppb) with short response (10–15 s) and recovery times (35–70 s). Furthermore, the sensor signal (response) was robust against variations of the exhaled breath flow rate facilitating application of these sensors at realistic relative humidities (80–90%) as in the human breath. The acetone content in the breath of test persons was monitored continuously and compared to that of state-of-the-art proton transfer reaction mass spectrometry (PTR-MS). Such portable devices can accurately track breath acetone concentration to become an alternative to more elaborate breath analysis techniques. PMID:22790702

Soybean lecithin: acetone insoluble residue fractionation and their volatile components

Directory of Open Access Journals (Sweden)

Aly, Saadia M.

2002-09-01

Full Text Available The acetone insoluble residue was isolated from soybean lecithin. This residue was solvent fractionated resulted in four fractions, namely, acetic acid soluble, acetic acid insoluble, benzene phase and benzene insoluble phase. Concerning phospholipid constitution of these four fractions, it was found that the first fraction contains PC, PE and PI in percentages of 56.0, 21.6 and 19.0 respectively. The 2nd fraction makes 39 % PC and 60 % CER, besides some traces of PE and PI. The benzene phase is mainly all PC with some traces of PE. The last fraction is 80.6 % CER and 20 % PC. The fatty acid composition of these four fractions besides soluble in acetone, crude and degummed soybean oil and total phospholipids was recorded. Generally, it was found that the major saturated and unsaturated fatty acids were palmitic and linoleic. Volatile components of these samples except acetic acid insoluble were reported. Fourty nine compounds were separated. Thirty two components including aliphatic aldehydes, ketones, alcohols, esters and acids were identified. Aldehydes and ketones showed a changed through the seven samples. They increased by degumming.4,5-Dimethylelisoxazole had a strong lecithin like flavour, so it can be used as an indicator for the degumming process.2-Pentylfuran showed a significant decrease by degumming. Other compounds, such as esters and alcohols had no distinguish effect on the volatile products through process.El residuo insoluble en acetona fue aislado de la lecitina de soja. Este residuo fue fraccionado por solventes en cuatro fracciones: soluble en ácido acético, insoluble en ácido acético, fase benceno y fase insoluble en benceno. Concerniente a la constitución de los fosfolípidos de estas cuatro fracciones, se encontró que la primera fracción contiene PC, PE y PI en porcentajes del 56.0, 21.6 y 19.0 respectivamente. La segunda fracción tuvo 39 % PC y 60 % CER, junto a algunas trazas de PE y PI. La fase benceno est

Home-made Detection Device for a Mixture of Ethanol and Acetone

Directory of Open Access Journals (Sweden)

Sukon Phanichphant

2007-02-01

Full Text Available A device for the detection and determination of ethanol and acetone wasconstructed, consisting of a packed column, a chamber with a sensor head, 2 dc powersupplies, a multimeter and a computer. A commercially available TGS 822 detector head(Figaro Company Limited was used as the sensor head. The TGS 822 detector consists of aSnO2 thick film deposited on the surface of an alumina ceramic tube which contains aheating element inside. An analytical column was coupled with the setup to enhance theseparation of ethanol and acetone before they reached the sensor head. Optimum systemconditions for detection of ethanol and acetone were achieved by varying the flow rate of thecarrier gas, voltage of the heating coil (VH, voltage of the circuit sensor (VC, loadresistance of the circuit sensor (RL and the injector port temperature. The flow of the carriergas was 15 mL/min; the circuit conditions were VH = 5.5 V, VC = 20 V, RL = 68 k ; and theinjection port temperature was 150°C. Under these conditions the retention times (tR forethanol and acetone were 1.95 and 0.57 minutes, respectively. Calibration graphs wereobtained for ethanol and acetone over the concentration range of 10 to 160 mg/L. The limitsof detection (LOD for ethanol and acetone were 9.25 mg/L and 4.41 mg/L respectively.

Synthesis of tetraalkyl thiuram disulfides using different oxidants in recycling solvent mixture

Directory of Open Access Journals (Sweden)

Milosavljević Milutin M.

2012-01-01

Full Text Available A new optimized laboratory synthesis of tetraalkyl thiuram disulfides, starting from dialkyl amines and carbon disulfide in presence of three oxidants (hydrogen peroxide, potassium peroxodisulfate and sodium hypochlorite and appropriate reaction medium: two mixtures of isopropyl alcohol - water used in two consecutive syntheses, was presented in this work. First synthesis was performed in a recycled azeotropic mixture of isopropyl alcohol - water 87.7% - 12.3%, and second in a filtrate obtained after first synthesis, which was a mixture of isopropyl alcohol - water 70.4% - 29.6%. After the second synthesis and filtration, recycled azeotropic mixture isopropyl alcohol - water 87.7% - 12.3% was regenerated from the filtrate by rectification. Considering this, the technology for beneficial use of recycling isopropyl alcohol - water mixture as reaction medium for tetraalkyl thiuram disulfides synthesis was developed. Such concept contributes to extraordinary economical benefit of implemented optimal laboratory synthesis at semi-industrial level. High yields of tetraalkyl thiuram disulfides syntheses were obtained at both laboratory and semiindustrial level. Structure and purity of synthesized compounds were confirmed by elemental analysis, as well as FTIR, 1H and 13C NMR, and MS spectral data.

Carbonylation as a key reaction in anaerobic acetone activation by Desulfococcus biacutus.

Science.gov (United States)

Gutiérrez Acosta, Olga B; Hardt, Norman; Schink, Bernhard

2013-10-01

Acetone is activated by aerobic and nitrate-reducing bacteria via an ATP-dependent carboxylation reaction to form acetoacetate as the first reaction product. In the activation of acetone by sulfate-reducing bacteria, acetoacetate has not been found to be an intermediate. Here, we present evidence of a carbonylation reaction as the initial step in the activation of acetone by the strictly anaerobic sulfate reducer Desulfococcus biacutus. In cell suspension experiments, CO was found to be a far better cosubstrate for acetone activation than CO2. The hypothetical reaction product, acetoacetaldehyde, is extremely reactive and could not be identified as a free intermediate. However, acetoacetaldehyde dinitrophenylhydrazone was detected by mass spectrometry in cell extract experiments as a reaction product of acetone, CO, and dinitrophenylhydrazine. In a similar assay, 2-amino-4-methylpyrimidine was formed as the product of a reaction between acetoacetaldehyde and guanidine. The reaction depended on ATP as a cosubstrate. Moreover, the specific activity of aldehyde dehydrogenase (coenzyme A [CoA] acylating) tested with the putative physiological substrate was found to be 153 ± 36 mU mg(-1) protein, and its activity was specifically induced in extracts of acetone-grown cells. Moreover, acetoacetyl-CoA was detected (by mass spectrometry) after the carbonylation reaction as the subsequent intermediate after acetoacetaldehyde was formed. These results together provide evidence that acetoacetaldehyde is an intermediate in the activation of acetone by sulfate-reducing bacteria.

Derivatization reaction-based surface-enhanced Raman scattering (SERS) for detection of trace acetone.

Science.gov (United States)

Zheng, Ying; Chen, Zhuo; Zheng, Chengbin; Lee, Yong-Ill; Hou, Xiandeng; Wu, Li; Tian, Yunfei

2016-08-01

A facile method was developed for determination of trace volatile acetone by coupling a derivatization reaction to surface-enhanced Raman scattering (SERS). With iodide modified Ag nanoparticles (Ag IMNPs) as the SERS substrate, acetone without obvious Raman signal could be converted to SERS-sensitive species via a chemical derivatization reaction with 2,4-dinitrophenylhydrazine (2,4-DNPH). In addition, acetone can be effectively separated from liquid phase with a purge-sampling device and then any serious interference from sample matrices can be significantly reduced. The optimal conditions for the derivatization reaction and the SERS analysis were investigated in detail, and the selectivity and reproducibility of this method were also evaluated. Under the optimal conditions, the limit of detection (LOD) for acetone was 5mgL(-1) or 0.09mM (3σ). The relative standard deviation (RSD) for 80mgL(-1) acetone (n=9) was 1.7%. This method was successfully used for the determination of acetone in artificial urine and human urine samples with spiked recoveries ranging from 92% to 110%. The present method is convenient, sensitive, selective, reliable and suitable for analysis of trace acetone, and it could have a promising clinical application in early diabetes diagnosis. Copyright © 2016 Elsevier B.V. All rights reserved.

Evaluation of acetone vapors toxicity on Plodia interpunctella (Hubner) (Lepidoptera: Pyralidae) eggs.

Science.gov (United States)

Pourmirza, Ali Asghr; Nasab, Fershteh Sadeghi; Zadeh, Abas Hossein

2007-08-01

The efficacy of acetone vapors against carefully aged eggs of Plodia interpunctella (Hubner) at 17+/-1 and 27+/-1 degrees C at different dosage levels of acetone over various exposure times was determined. Acetone was found to be toxic to Indian meal moth eggs. Considerable variation in the susceptibility of different age groups of eggs was apparent in the fiducial limits of the LD50 values. An inverse relationship between LD50 values and exposure times was observed in age groups of tested eggs. At 27+/-1 degrees C and 24 h exposure period, eggs aged 1-2 day-old were more tolerant to acetone than other age groups, followed by 0-1 day-old, 2-3 day-old and 3-4 day-old eggs. A similar pattern of susceptibility of eggs was observed at 72 h exposure. In all bioassays, eggs exposed to higher dosages of acetone developed at smaller rate. This was significant for the eggs, which were exposed to the highest dosage for 24 h. Increasing the temperature from 17+/-1 to 27+/-1 degrees C greatly increased the efficacy of acetone. At 27+/-1 degrees C eggs of P. interpunctella were killed by less than one-third of the dosage required for control at 17+/-1 degrees C. Acetone achieved 50% mortality with a dosage of 82.76 mg L(-1) in 1-2 day-old eggs at 27+/-1 degrees C. At this temperature hatching was retarded and greatly diminished when eggs aged 1-2 day-old were exposed to 80 mg L(-1) of acetone for the 24 h exposure period. There was no evidence of a hatch delay longer than the time spent under vapors for eggs exposed at 17+/-1 or 27+/-1 degrees C, indicating that some development must have occurred under fumigation.

Decomposition of three volatile organic compounds by nanosecond pulsed corona discharge: Study of by-product formation and influence of high voltage pulse parameters

Science.gov (United States)

Jarrige, Julien; Vervisch, Pierre

2006-06-01

Increasing concerns over atmospheric pollution has motivated research into technologies able to remove volatile organic compounds (VOC's) from gas streams. The aim of this paper is to understand the chemical and physical mechanisms implied in the decomposition of VOC's in a filamentary nonthermal plasma discharge. Experiments have been carried out on three pollutants (propane, propene, and isopropyl alcohol) in dry air at atmospheric pressure using a wire to cylinder corona discharge generated by a homemade nanosecond rise time high voltage pulse generator. The resulting plasma efficiently destructs propane, propene, or isopropyl alcohol at a concentration of 500 ppm with low specific input energies (less than 500 J/L), but the poor oxidation rate leads to the formation of numerous by-products (acetone, formaldehyde, formic acid, and methyl nitrate) whose concentration can reach some hundreds of ppm. We also investigated the effect of pulse parameters on VOC removal efficiency. Neither pulse peak value nor rise time (in the range of 4-12 ns) appears to have a significant influence on the VOC decomposition rates. Therefore, we believe that the way the energy is deposited in the plasma does not modify the density of active species (radicals, ions) in the streamers. The production of energetic electrons is not enhanced by the external applied field, and the only effective parameter may be the local field in the streamer head, which is almost the same (around 500 Td) whatever the voltage (above the inception value).

Decomposition of three volatile organic compounds by nanosecond pulsed corona discharge: Study of by-product formation and influence of high voltage pulse parameters

International Nuclear Information System (INIS)

Jarrige, Julien; Vervisch, Pierre

2006-01-01

Increasing concerns over atmospheric pollution has motivated research into technologies able to remove volatile organic compounds (VOC's) from gas streams. The aim of this paper is to understand the chemical and physical mechanisms implied in the decomposition of VOC's in a filamentary nonthermal plasma discharge. Experiments have been carried out on three pollutants (propane, propene, and isopropyl alcohol) in dry air at atmospheric pressure using a wire to cylinder corona discharge generated by a homemade nanosecond rise time high voltage pulse generator. The resulting plasma efficiently destructs propane, propene, or isopropyl alcohol at a concentration of 500 ppm with low specific input energies (less than 500 J/L), but the poor oxidation rate leads to the formation of numerous by-products (acetone, formaldehyde, formic acid, and methyl nitrate) whose concentration can reach some hundreds of ppm. We also investigated the effect of pulse parameters on VOC removal efficiency. Neither pulse peak value nor rise time (in the range of 4-12 ns) appears to have a significant influence on the VOC decomposition rates. Therefore, we believe that the way the energy is deposited in the plasma does not modify the density of active species (radicals, ions) in the streamers. The production of energetic electrons is not enhanced by the external applied field, and the only effective parameter may be the local field in the streamer head, which is almost the same (around 500 Td) whatever the voltage (above the inception value)

Weak carbonyl-methyl intermolecular interactions in acetone clusters explored by IR plus VUV spectroscopy

International Nuclear Information System (INIS)

Guan, Jiwen; Hu, Yongjun; Xie, Min; Bernstein, Elliot R.

2012-01-01

Highlights: ► The carbonyl overtone of acetone clusters is observed by IR-VUV spectroscopy. ► Acetone molecules in the dimer are stacked with an antiparallel way. ► The structure of the acetone trimer and the tetramer are the cyclic structures. ► The carbonyl groups would interact with the methyl groups in acetone clusters. ► These weak interactions are further confirmed by H/D substitution experiment. -- Abstract: Size-selected IR–VUV spectroscopy is employed to detect vibrational characteristics in the region 2850 ∼ 3550 cm −1 of neutral acetone and its clusters (CH 3 COCH 3 ) n (n = 1–4). Features around 3440 cm −1 in the spectra of acetone monomer and its clusters are assigned to the carbonyl stretch (CO) overtone. These features red-shift from 3455 to 3433 cm −1 as the size of the clusters increases from the monomer to the tetramer. Based on calculations, the experimental IR spectra in the C=O overtone region suggest that the dominant structures for the acetone trimer and tetramer should be cyclic in the supersonic expansion sample. This study also suggests that the carbonyl groups interact with the methyl groups in the acetone clusters. These weak interactions are further confirmed by the use of deuterium substitution.

Solvents (butanol, acetone, and ethanol)

Energy Technology Data Exchange (ETDEWEB)

Yarovenko, V L; Nakhmanovich, B M

1963-07-17

The method involves use of carbohydrate containing plant raw-material, e.g., hydrolyzates of corn cob and pulp. The material is subjected to fermentation with acetone-butanol bacteria with addition of starch-industry wastes as source of proteins (gluten and gluten-containing water) and nutrient salts.

Fermentation and genomic analysis of acetone-uncoupled butanol production by Clostridium tetanomorphum.

Science.gov (United States)

Gong, Fuyu; Bao, Guanhui; Zhao, Chunhua; Zhang, Yanping; Li, Yin; Dong, Hongjun

2016-02-01

In typical acetone-butanol-ethanol (ABE) fermentation, acetone is the main by-product (50 % of butanol mass) of butanol production, resulting in a low yield of butanol. It is known that some Clostridium tetanomorphum strains are able to produce butanol without acetone in nature. Here, we described that C. tetanomorphum strain DSM665 can produce 4.16 g/L butanol and 4.98 g/L ethanol at pH 6.0, and 9.81 g/L butanol and 1.01 g/L ethanol when adding 1 mM methyl viologen. Butyrate and acetate could be reassimilated and no acetone was produced. Further analysis indicated that the activity of the acetate/butyrate:acetoacetyl-CoA transferase responsible for acetone production is lost in C. tetanomorphum DSM665. The genome of C. tetanomorphum DSM665 was sequenced and deposited in DDBJ, EMBL, and GenBank under the accession no. APJS00000000. Sequence analysis indicated that there are no typical genes (ctfA/B and adc) that are typically parts of an acetone synthesis pathway in C. tetanomorphum DSM665. This work provides new insights in the mechanism of clostridial butanol production and should prove useful for the design of a high-butanol-producing strain.

A Novel Sensor for VOCs Using Nanostructured ZnO and MEMS Technologies

Directory of Open Access Journals (Sweden)

H. J. Pandya

2012-03-01

Full Text Available A sensor for detection of vapors of volatile organic compounds (VOCs incorporating nanostructured zinc oxide film and silicon micromachining is reported. One of the key features of the sensor is the use of nanostructured ZnO material which has been synthesized using a novel low cost process. Considerable reduction in the operating temperature of the sensor has been achieved due to the use of nanostructured ZnO material as compared to a sensor having ZnO thin film as the sensing layer. The sensor is formed on a micromachined silicon platform thereby reducing the heat loss. This resulted in reduction in power consumption. The sensor has been tested for a variety of VOCs such as: ethanol, iso-propyl alcohol and acetone. The maximum sensitivity of sensor was observed for ethanol vapors.

An isotope dependent study of acetone in its lowest excited triplet state

International Nuclear Information System (INIS)

Gehrtz, M.; Brauchle, C.; Voitlaender, J.

1984-01-01

The lowest excited triplet state T 1 of acetone-h 6 and acetone-d 6 was investigated with a pulsed dye laser equipped ODMR spectrometer. Acetone is found to be bent in T 1 and the out-of-plane distortion angle is estimated to be approx.= 38 0 . The observed zero-field splitting (ZFS) is surprisingly small. Both the spin-spin and the spin-orbit (SO) contribution to the ZFS are evaluated. The SO tensor contribution is calculated from a correlation between the deuterium effects on the ZFS parameters and the population rates. The sub-level selective kinetics of the acetone T 1 is largely determined by the mixing of the x- and z-level characteristics owing to magnetic axis rotation caused by the excited state out-of-plane distortion. Considerable deuterium effects are observed on the kinetic data and on the microwave transition frequencies. In all cases the spin-specific isotope effects (due to the promoting modes) and the global effects (due to the Franck-Condon factors) are specified. For the population rates and the SO contribution to ZFS, the inverse global isotope effects (deuterium factor > 1) was found for the first time. Based on the isotope dependence of the rates, the mechanisms of (vibrationally induced) SO coupling in acetone are discussed. It is concluded that non-adiabatic contributions have to be taken into account for the smallest population rate only, but that otherwise the adiabatic SO coupling mechanisms by far dominates in the acetone photophysics. (author)

Performance of Cr-doped ZnO for acetone sensing

Energy Technology Data Exchange (ETDEWEB)

Al-Hardan, N.H., E-mail: naif_imen@ukm.my [Institute of Microengineering and Nanoelectronics (IMEN), Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Abdullah, M.J.; Aziz, A. Abdul [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia)

2013-04-01

Zinc oxide (ZnO) doped with chromium (Cr) was synthesized by reactive co-sputtering for gas sensing applications. The effect of varying the contents of Cr (from 1 to 4 at%) on the ZnO gas sensor response was studied. X-ray diffraction analysis reveals the high orientation of c-axis of the prepared films. The optimum operating temperature of the undoped ZnO was 400 °C and shifted to 300 °C for the Cr-doped ZnO under the acetone vapour. The 1% Cr doping ZnO gas sensor was most sensitive for the acetone vapour. The ability of the 1% Cr-doped ZnO to produce repeatable results under different acetone vapour concentrations was tested. The timing properties of the doped Cr ZnO gas sensor were 70 and 95 s for the rise and recovery time respectively.

Selective bio-oxidation of propane to acetone using methane-oxidizing Methylomonas sp. DH-1.

Science.gov (United States)

Hur, Dong Hoon; Nguyen, Thu Thi; Kim, Donghyuk; Lee, Eun Yeol

2017-07-01

Propane is the major component of liquefied petroleum gas (LPG). Nowadays, the use of LPG is decreasing, and thus utilization of propane as a chemical feedstock is in need of development. An efficient biological conversion of propane to acetone using a methanotrophic whole cell as the biocatalyst was proposed and investigated. A bio-oxidation pathway of propane to acetone in Methylomonas sp. DH-1 was analyzed by gene expression profiling via RNA sequencing. Propane was oxidized to 2-propanol by particulate methane monooxygenase and subsequently to acetone by methanol dehydrogenases. Methylomonas sp. DH-1 was deficient in acetone-converting enzymes and thus accumulated acetone in the absence of any enzyme inhibition. The maximum accumulation, average productivity and specific productivity of acetone were 16.62 mM, 0.678 mM/h and 0.141 mmol/g cell/h, respectively, under the optimized conditions. Our study demonstrates a novel method for the bioconversion of propane to acetone using methanotrophs under mild reaction condition.

Multiphoton ionization and fragmentation study of acetone using 308 nm laser radiation

Science.gov (United States)

Liu Houxiang, Li Shutao, Han Jingcheng, Zhu Rong, Guan Yifu, Wu Cunkai

1988-10-01

Multiphoton ionization and fragmentation (MPI-F) of acetone molecules using 308 nm laser radiation was studied by using a molecular beam and quadrupole mass spectrometer. The ion peaks of acetone molecule appear at m/e=15 and 43, corresponding to the two fragments CH3+ and CH3CO+. It is considered that these two ions are, respectively, formed by direct (2+1) and 2-photon ionization of methyl and acetyl radicals, generated by photodissociation of acetone molecule.

Efficient acetone-butanol-ethanol production by Clostridium beijerinckii from sugar beet pulp.

Science.gov (United States)

Bellido, Carolina; Infante, Celia; Coca, Mónica; González-Benito, Gerardo; Lucas, Susana; García-Cubero, María Teresa

2015-08-01

Sugar beet pulp (SBP) has been investigated as a promising feedstock for ABE fermentation by Clostridium beijerinckii. Although lignin content in SBP is low, a pretreatment is needed to enhance enzymatic hydrolysis and fermentation yields. Autohydrolysis at pH 4 has been selected as the best pretreatment for SBP in terms of sugars release and acetone and butanol production. The best overall sugars release yields from raw SBP ranged from 66.2% to 70.6% for this pretreatment. The highest ABE yield achieved was 0.4g/g (5.1g/L of acetone and 6.6g/L butanol) and 143.2g ABE/kg SBP (62.3g acetone and 80.9g butanol) were obtained when pretreated SBP was enzymatically hydrolyzed at 7.5% (w/w) solid loading. Higher solid loadings (10%) offered higher acetone and butanol titers (5.8g/L of acetone and 7.8g/L butanol). All the experiments were carried out under not-controlling pH conditions reaching about 5.3 in the final samples. Copyright © 2015 Elsevier Ltd. All rights reserved.

An analysis of human response to the irritancy of acetone vapors

NARCIS (Netherlands)

Arts, J.H.E.; Mojet, J.; Gemert, L.J. van; Emmen, H.H.; Lammers, J.H.C.M.; Marquart, J.; Woutersen, R.A.; Feron, V.J.

2002-01-01

Studies on the irritative effects of acetone vapor in humans and experimental animals have revealed large differences in the lowest acetone concentration found to be irritative to the respiratory tract and eyes. This has brought on much confusion in the process of setting occupational exposure

[Removal of high-abundance proteins in plasma of the obese by improved TCA/acetone precipitation method].

Science.gov (United States)

Wang, Jun; Feng, Liru; Yu, Wei; Xu, Jian; Yang, Hui; Liu, Xiaoli

2013-09-01

To develop an improved trichloroacetic acid (TCA)/acetone precipitation method for removal of high-abundance proteins in plasma of the obese. Volumes of TCA/acetone solution (1, 3, 4, 5, 6, 8, 10 and 20 times of the sample) and concentrations of TCA (10%, 30%, 50%, 60%, 70% TCA/acetone solution) have been investigated to optimize the conditions of sample preparation. SDS-PAGE were used to separate and tested proteins in the supernatant and sediment. The best concentration of the TCA/acetone solution was first determined by SDS-PAGE. The protein in precipitation from 10% TCA/acetone solution processing and the new determined concentration TCA/acetone solution processing were verified by 2-D-SDS-PAGE. And then the digested products of the protein in precipitation and supernatant by trypsin were analyzed by nano HPLC-Chip-MS/MS to verify which is the best concentration to process the plasma. The best volume of TCA/acetone is four times to sample, which less or more TCA/acetone would reduce the removal efficiency of high-abundance proteins. The concentration of TCA in acetone solution should be 60%, which may remove more high-abundance proteins in plasma than 10%, 30%, 50% TCA in acetone solution. If the TCA concentration is more than 60%, the reproducibility will be much poorer due to fast precipitation of proteins. The results of mass identification showed that human plasma prepared with 60% TCA/acetone (4 times sample volume) could be verified more low-abundance proteins than 10%. The most desirable conditions for removal of high-abundance proteins in plasma is 60% TCA/acetone (4 times sample volume), especially for the plasma of obesity.

Measurement of natural carbon isotopic composition of acetone in human urine.

Science.gov (United States)

Yamada, Keita; Ohishi, Kazuki; Gilbert, Alexis; Akasaka, Mai; Yoshida, Naohiro; Yoshimura, Ryoko

2016-02-01

The natural carbon isotopic composition of acetone in urine was measured in healthy subjects using gas chromatography-combustion-isotope ratio mass spectrometry combined with headspace solid-phase microextraction (HS-SPME-GC-C-IRMS). Before applying the technique to a urine sample, we optimized the measurement conditions of HS-SPME-GC-C-IRMS using aqueous solutions of commercial acetone reagents. The optimization enabled us to determine the carbon isotopic compositions within ±0.2 ‰ of precision and ±0.3‰ of error using 0.05 or 0.2 mL of aqueous solutions with acetone concentrations of 0.3-121 mg/L. For several days, we monitored the carbon isotopic compositions and concentrations of acetone in urine from three subjects who lived a daily life with no restrictions. We also monitored one subject for 3 days including a fasting period of 24 h. These results suggest that changes in the availability of glucose in the liver are reflected in changes in the carbon isotopic compositions of urine acetone. Results demonstrate that carbon isotopic measurement of metabolites in human biological samples at natural abundance levels has great potential as a tool for detecting metabolic changes caused by changes in physiological states and disease.

A Portable Real-Time Ringdown Breath Acetone Analyzer: Toward Potential Diabetic Screening and Management.

Science.gov (United States)

Jiang, Chenyu; Sun, Meixiu; Wang, Zhennan; Chen, Zhuying; Zhao, Xiaomeng; Yuan, Yuan; Li, Yingxin; Wang, Chuji

2016-07-30

Breath analysis has been considered a suitable tool to evaluate diseases of the respiratory system and those that involve metabolic changes, such as diabetes. Breath acetone has long been known as a biomarker for diabetes. However, the results from published data by far have been inconclusive regarding whether breath acetone is a reliable index of diabetic screening. Large variations exist among the results of different studies because there has been no "best-practice method" for breath-acetone measurements as a result of technical problems of sampling and analysis. In this mini-review, we update the current status of our development of a laser-based breath acetone analyzer toward real-time, one-line diabetic screening and a point-of-care instrument for diabetic management. An integrated standalone breath acetone analyzer based on the cavity ringdown spectroscopy technique has been developed. The instrument was validated by using the certificated gas chromatography-mass spectrometry. The linear fittings suggest that the obtained acetone concentrations via both methods are consistent. Breath samples from each individual subject under various conditions in total, 1257 breath samples were taken from 22 Type 1 diabetic (T1D) patients, 312 Type 2 diabetic (T2D) patients, which is one of the largest numbers of T2D subjects ever used in a single study, and 52 non-diabetic healthy subjects. Simultaneous blood glucose (BG) levels were also tested using a standard diabetic management BG meter. The mean breath acetone concentrations were determined to be 4.9 ± 16 ppm (22 T1D), and 1.5 ± 1.3 ppm (312 T2D), which are about 4.5 and 1.4 times of the one in the 42 non-diabetic healthy subjects, 1.1 ± 0.5 ppm, respectively. A preliminary quantitative correlation (R = 0.56, p acetone concentration and the mean individual BG levels does exist in 20 T1D subjects with no ketoacidosis. No direct correlation is observed in T1D subjects, T2D subjects, and healthy subjects. The results

Experimental results of acetone hydrogenation on a heat exchanger type reactor for solar chemical heat pump; Solar chemical heat pump ni okeru acetone suisoka hanno netsu kaishu jikken

Energy Technology Data Exchange (ETDEWEB)

Takashima, T; Doi, T; Tanaka, T; Ando, Y [Electrotechnical Laboratory, Tsukuba (Japan); Miyahara, R; Kamoshida, J [Shibaura Institute of Technology, Tokyo (Japan)

1996-10-27

With the purpose of converting solar heat energy to industrial heat energy, an experiment of acetone hydrogenation was carried out using a heat exchanger type reactor that recovers heat generated by acetone hydrogenation, an exothermic reaction, and supplies it to an outside load. In the experiment, a pellet-like activated carbon-supported ruthenium catalyst was used for the acetone hydrogenation with hydrogen and acetone supplied to the catalyst layer at a space velocity of 400-1,200 or so. In the external pipe of the double-pipe type reactor, a heating medium oil was circulated in parallel with the flow of the reactant, with the heat of reaction recovered that was generated from the acetone hydrogenation. In this experiment, an 1wt%Ru/C catalyst and a 5wt%Ru/C catalyst were used so as to examine the effects of variation in the space velocity. As a result, from the viewpoint of recovering the heat of reaction, it was found desirable to increase the reaction speed by raising catalytic density and also to supply the reactant downstream inside the reaction pipe by increasing the space velocity. 1 ref., 6 figs., 1 tab.

Phase equilibrium properties of binary and ternary systems containing di-isopropyl ether + 1-butanol + benzene at 313.15 K

International Nuclear Information System (INIS)

Villamanan, Rosa M.; Martin, M. Carmen; Chamorro, Cesar R.; Villamanan, Miguel A.; Segovia, Jose J.

2006-01-01

(Vapour + liquid) equilibria data of (di-isopropyl ether + 1-butanol + benzene) (di-isopropyl ether + 1-butanol) and (1-butanol + benzene) have been measured at T = 313.15 K using an isothermal total pressure cell. Data reduction by Barker's method provides correlations for the excess molar Gibbs energy using the Margules equation for the binary systems and the Wohl expansion for the ternary. The Wilson, NRTL and UNIQUAC models have been applied successfully to both the binary and the ternary systems reported here

Diagnosis by acetone for deterioration of breathing transformers containing an adsorbent in the insulating oil; Acetone ni yoru kyuchakuzai iri kaihogata hen`atsuki no keinen rekkado shindan

Energy Technology Data Exchange (ETDEWEB)

Awata, M.; Mizuno, K.; Ueda, T. [Chubu Electric Power Co. Ltd., Nagoya (Japan); Ota, N.; Ishii, T.; Tsukioka, H.

1997-04-20

The high-precision diagnosis for deterioration of a breathing transformer containing an adsorbent was investigated. An adsorbent (activated alumina) may be contained in oil to eliminate the deterioration product in insulating oil or the moisture. In this case, the deterioration component furfural in insulating paper is adsorbed. The concentration in furfural oil cannot be thus used for deterioration diagnosis. Acetone and furan with good relation between the adsorption characteristics for activated alumina and the insulating paper deterioration in an accelerated deterioration test can be effectively used as a new deterioration index component of insulating paper. The disassembly survey showed that acetone is valid as the index component of deterioration diagnosis. Furan is not detected in a breathing transformer, but effective in diaphragm-type and nitrogen-sealed transformers. The adsorption of acetone by activated alumina requires no correction for the change in oil temperature at about 10{degree}C. The solubility of acetone for insulating oil is 60 times at 20{degree}C as high as CO2, and the discharge rate from a breather is little (1/25). Therefore, acetone is much more excellent than CO2 as the precision of a deterioration index. 21 refs., 15 figs., 4 tabs.

Metabolic lung scanning with N-isopropyl-I-123-p-iodoamphetamine

International Nuclear Information System (INIS)

Touya, J.; Akber, S.F.; Rashimian, J.; Bennett, L.R.

1982-01-01

The mechanisms of uptake of N-Isopropyl-I-123-p-Iodoamphetamine (IMP) in the lung was studied in dogs. It has been concluded that this amine is taken in low specificity - high capacity endothelial receptors. Competitive effect of propranolol guanethidine, amphetamine and ketanine for the binding sites of IMP in the pulmonary endothelial cells was observed. These results show that IMP can be an agent for nonparticulate lung perfusion scans as well as for metabolic lung scans

Ligands Exchange Process on Gold Nanoparticles in Acetone Solution

Science.gov (United States)

Hu, C. L.; Mu, Y. Y.; Bian, Z. C.; Luo, Z. H.; Luo, K.; Huang, A. Z.

2018-05-01

The ligands exchange process on gold nanoparticles (GNPs) was proceeded by using hydrophobic group (PPh3) and hydrophilic group (THPO) in acetone solution. The FTIR and XPS results demonstrated that part of THPO was replaced by PPh3 which was dissolved in polar solution (acetone); the results were in accordance with the electrochemical analysis where the differential capacity decreased with increasing exchange time. After 12 h, the exchange process terminated and the final ratio of PPh3 and THPO was about 1.4: 1. This ratio remained unchanged although the PPh3 and THPO modified GNPs re-dispersed in the PPh3 acetone solution demonstrating the stable adsorption of both ligands after exchanging for 12 h. The TEM images showed that the gold nanoparticles were self-assembled from scattered to arranged morphology due to the existence of hydrophilic and hydrophobic ligands and led to Janus gold nanoparticles.

Acetaminophen and acetone sensing capabilities of nickel ferrite nanostructures

Science.gov (United States)

Mondal, Shrabani; Kumari, Manisha; Madhuri, Rashmi; Sharma, Prashant K.

2017-07-01

Present work elucidates the gas sensing and electrochemical sensing capabilities of sol-gel-derived nickel ferrite (NF) nanostructures based on the electrical and electrochemical properties. In current work, the choices of target species (acetone and acetaminophen) are strictly governed by their practical utility and concerning the safety measures. Acetone, the target analyte for gas sensing measurement is a common chemical used in varieties of application as well as provides an indirect way to monitor diabetes. The gas sensing experiments were performed within a homemade sensing chamber designed by our group. Acetone gas sensor (NF pellet sensor) response was monitored by tracking the change in resistance both in the presence and absence of acetone. At optimum operating temperature 300 °C, NF pellet sensor exhibits selective response for acetone in the presence of other common interfering gases like ethanol, benzene, and toluene. The electrochemical sensor fabricated to determine acetaminophen is prepared by coating NF onto the surface of pre-treated/cleaned pencil graphite electrode (NF-PGE). The common name of target analyte acetaminophen is paracetamol (PC), which is widespread worldwide as a well-known pain killer. Overdose of PC can cause renal failure even fatal diseases in children and demand accurate monitoring. Under optimal conditions NF-PGE shows a detection limit as low as 0.106 μM with selective detection ability towards acetaminophen in the presence of ascorbic acid (AA), which co-exists in our body. Use of cheap and abundant PGE instead of other electrodes (gold/Pt/glassy carbon electrode) can effectively reduce the cost barrier of such sensors. The obtained results elucidate an ample appeal of NF-sensors in real analytical applications viz. in environmental monitoring, pharmaceutical industry, drug detection, and health monitoring.

PREPARATION AND CATALYTIC ACTIVITY FOR ISOPROPYL BENZENE CRACKING OF Co, Mo AND Co/Mo-Al2O3-PILLARED MONTMORILLONITE CATALYSTS

Directory of Open Access Journals (Sweden)

Hasanudin Hasanudin

2010-06-01

Full Text Available It has been prepared Co, Mo and Co/Mo-Al2O3-pillared montmorillonite catalysts using montmorillonite clay  as raw material. The structure and porosity of the catalysts were determined using N2 adsorption-desorption and FT-IR spectroscopy analysis methods. Isopropyl benzene cracking using these catalysts were used to test the catalytic activity and performance of Co, Mo and Co/Mo-Al2O3-pillared montmorillonites.  Characterization results showed that pillarization resulted in the increase of the total pore volume and specific surface area of the clay. Meanwhile, transition metals (Co, Mo and Co/Mo loaded on Al2O3-pillared monmorillonites could increase the catalytic activity of the catalysts for isopropyl benzene cracking significantly.   Keywords: pillared monmorillonite, isopropyl benzene  and cracking catalyst

A simple synthesis of 2-keto-3-deoxy-D-erythro-hexonic acid isopropyl ester, a key sugar for the bacterial population living under metallic stress.

Science.gov (United States)

Grison, Claire M; Renard, Brice-Loïc; Grison, Claude

2014-02-01

2-Keto-3-deoxy-D-erythro-hexonic acid (KDG) is the key intermediate metabolite of the Entner Doudoroff (ED) pathway. A simple, efficient and stereoselective synthesis of KDG isopropyl ester is described in five steps from 2,3-O-isopropylidene-D-threitol with an overall yield of 47%. KDG isopropyl ester is studied as an attractive marker of a functional Entner Doudoroff pathway. KDG isopropyl ester is used to promote growth of ammonium producing bacterial strains, showing interesting features in the remediation of heavy-metal polluted soils. Copyright © 2013 Elsevier Inc. All rights reserved.

Catalytic Hydrogenation of Acetone to Isopropanol: An Environmentally Benign Approach

Directory of Open Access Journals (Sweden)

Ateeq Rahman

2011-01-01

Full Text Available The catalytic hydrogenation of acetone is an important area of catalytic process to produce fine chemicals. Hydrogenation of acetone has important applications for heat pumps, fuel cells or in fulfilling the sizeable demand for the production of 2-propanol. Catalytic vapour phase hydrogenation of acetone has gained attention over the decades with variety of homogeneous catalysts notably Iridium, Rh, Ru complexes and heterogeneous catalysts comprising of Raney Nickel, Raney Sponge, Ni/Al2O3, Ni/SiO2, or Co-Al2O3, Pd, Rh, Ru, Re, or Fe/Al2O3 supported on SiO2 or MgO and even CoMgAl, NiMg Al layered double hydroxide, Cu metal, CuO, Cu2O. Nano catalysts are developed for actone reduction Ni maleate, cobalt oxide prepared in organic solvents. Author present a review on acetone hydrogenation under different conditions with various homogeneous and heterogeneous catalysts studied so far in literature and new strategies to develop economic and environmentally benign approach. ©2010 BCREC UNDIP. All rights reserved(Received: 16th June 2010, Revised: 18th October 2010; Accepted: 25th October 2010[How to Cite:Ateeq Rahman. (2010. Catalytic Hydrogenation of Acetone to Isopropanol: An Environmentally Benign Approach. Bulletin of Chemical Reaction Engineering and Catalysis, 5(2: 113-126. doi:10.9767/bcrec.5.2.798.113-126][DOI: http://dx.doi.org/10.9767/bcrec.5.2.798.113-126 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/798

Synthesis of N-isopropyl p-[123I]iodoamphetamine via organoborane chemistry

International Nuclear Information System (INIS)

Kabalka, G.W.; Varma, R.S.; Gai, Y.

1990-01-01

Iodine-123 labeled amphetamines have proven to be excellent cerebral perfusion tracers. The radioiodination of aromatic amines is generally achieved via high temperature substitution reactions which are prone to side reactions. The authors report that N-isopropyl p-[ 123 I]iodoamphetamine, and other iodophenylamines, are readily synthesized from the corresponding air stable, boronic acids. The reaction is based on the no-carrier-added radioiodination sequence developed in their laboratory

Breath acetone to monitor life style interventions in field conditions: an exploratory study.

Science.gov (United States)

Samudrala, Devasena; Lammers, Gerwen; Mandon, Julien; Blanchet, Lionel; Schreuder, Tim H A; Hopman, Maria T; Harren, Frans J M; Tappy, Luc; Cristescu, Simona M

2014-04-01

To assess whether breath acetone concentration can be used to monitor the effects of a prolonged physical activity on whole body lipolysis and hepatic ketogenesis in field conditions. Twenty-three non-diabetic, 11 type 1 diabetic, and 17 type 2 diabetic subjects provided breath and blood samples for this study. Samples were collected during the International Four Days Marches, in the Netherlands. For each participant, breath acetone concentration was measured using proton transfer reaction ion trap mass spectrometry, before and after a 30-50 km walk on four consecutive days. Blood non-esterified free fatty acid (NEFA), beta-hydroxybutyrate (BOHB), and glucose concentrations were measured after walking. Breath acetone concentration was significantly higher after than before walking, and was positively correlated with blood NEFA and BOHB concentrations. The effect of walking on breath acetone concentration was repeatedly observed on all four consecutive days. Breath acetone concentrations were higher in type 1 diabetic subjects and lower in type 2 diabetic subjects than in control subjects. Breath acetone can be used to monitor hepatic ketogenesis during walking under field conditions. It may, therefore, provide real-time information on fat burning, which may be of use for monitoring the lifestyle interventions. Copyright © 2014 The Obesity Society.

Self-Diffusion and Heteroassociation in an Acetone-Chloroform Mixture at 298 K

Science.gov (United States)

Golubev, V. A.; Gurina, D. L.; Kumeev, R. S.

2018-01-01

The self-diffusion coefficients of acetone and chloroform in a binary acetone-chloroform mixture at 298 K are determined via pulsed field gradient NMR spectroscopy. It is estimated that the hydrodynamic radii of the mixture's components, calculated using the Stokes-Einstein equation, grow as the concentrations of the components fall. It is shown that such behavior of hydrodynamic radii is due to acetone-chloroform heteroassociation. The hydrodynamic radii of monomers and heteroassociates in a 1: 1 ratio are determined along with the constant of heteroassociation, using the proposed model of an associated solution.

Sodium tripolyphosphate cross-linked chitosan based sensor for enhacing sensing properties towards acetone

Science.gov (United States)

Nasution, T. I.; Asrosa, R.; Nainggolan, I.; Balyan, M.; Indah, R.; Wahyudi, A.

2018-02-01

In this report, sensing properties of sodium tripolyphosphate (TPP) cross-linked chitosan based sensor has been successfully enhanced towards acetone. Chitosan solutions were cross-linked with sodium TPP in variation of 0.1%, 0.5%, 1% and 1.5% w/v, respectively. The sensors were fabricated in film form using an electrochemical deposition method. The sensing properties of the sensors were observed by exposing the pure chitosan and sodium TPP cross-linked chitosan sensors towards acetone concentrations of 5, 10, 50, 100 and 200 ppm. The measurement results revealed that the maximum response in output voltage value of pure chitosan sensor was 0.35 V while sodium TPP crosslinked chitosan sensors were above 0.35 V towards 5 ppm acetone concentration. When the sensors were exposed towards acetone concentration of 200 ppm, the maximum response of pure chitosan was 0.45 V while sodium TPP crosslinked chitosan sensors were above 0.45 V. Amongst the variation of sodium TPP, the maximum response of 1% sodium TPP was the highest since the maximum response was 0.4 V and 0.6 V towards 5 ppm and 200 ppm acetone concentration, respectively. While the maximum responses of other sodium TPP concentrations were under 0.4 V and 0.6 V towards 5 ppm and 200 ppm acetone concentration. Moreover, 1% sodium TPP cross-linked chitosan based sensor showed good reproducibility and outstanding lifetime. Therefore, 1% sodium TPP cross-linked chitosan based sensor has exhibited remarkable sensing properties as a novel acetone sensor.

Synthesis 1, 3-bis (4-bromophenyl-5-isopropyl-1, 3, 5-triazacyclohexane

Directory of Open Access Journals (Sweden)

L. LEFRADA

2015-03-01

Full Text Available Condensation of an isopropylamine and an 4-bromoaniline with formaline in basic solution to give 1, 3-bis (4-bromophenyl-5- (isopropyl- 1, 3, 5- triazicyaclohexane. Through the interaction of rapid Schiff base, Structures of this compound have been elucidated by spectroscopic methods; IR, 1H NMR, 13C NMR. Their purities were confirmed by elemental analyses.

A clinical study of auditory hallucination by single photon emission computed tomography (SPECT) using N-isopropyl-p-[123I] iodoamphetamine (IMP)

International Nuclear Information System (INIS)

Gyobu, Tsuyoshi; Inao, Gyoshun; Ii, Masayasu; Matsuda, Hiroshi; Hisada, Kinichi.

1988-01-01

SPECT images with N-isopropyl-p-I-123 iodoamphetamine (IMP) were reviewed in 24 right-handed patients with hallucination (H Group), comprising schizophrenic disorder (20), alcohol hallucinosis (2), epileptic hallucinosis (one), and organic mental disorder (one), and 50 subjects without hallucination (non-H Group), consisting of 39 patients with mental or organic central nervous system disorder and 11 healthy volunteers. Early SPECT images showed an increased uptake of IMP in the auditory area and angular gyrus in 23 patients of H Group and 3 persons of non-H Group. A similar uptake of IMP was seen on delayed SPECT images in 12 patients of H Group and 4 patients with a history of hallucination of non-H Group. There were no SPECT findings specific to diseases. For schizophrenic patients, increased and decreased uptakes of IMP were seen in the striatolimbic region and in the bilateral frontal lobes, respectively, irrespective of hallucination. Factors contributing to increased uptake of IMP are discussed. (Namekawa, K.) 84 refs

Interactions of ionic liquids and acetone: thermodynamic properties, quantum-chemical calculations, and NMR analysis.

Science.gov (United States)

Ruiz, Elia; Ferro, Victor R; Palomar, Jose; Ortega, Juan; Rodriguez, Juan Jose

2013-06-20

The interactions between ionic liquids (ILs) and acetone have been studied to obtain a further understanding of the behavior of their mixtures, which generally give place to an exothermic process, mutual miscibility, and negative deviation of Raoult's law. COSMO-RS was used as a suitable computational method to systematically analyze the excess enthalpy of IL-acetone systems (>300), in terms of the intermolecular interactions contributing to the mixture behavior. Spectroscopic and COSMO-RS results indicated that acetone, as a polar compound with strong hydrogen bond acceptor character, in most cases, establishes favorable hydrogen bonding with ILs. This interaction is strengthened by the presence of an acidic cation and an anion with dispersed charge and non-HB acceptor character in the IL. COSMO-RS predictions indicated that gas-liquid and vapor-liquid equilibrium data for IL-acetone systems can be finely tuned by the IL selection, that is, acting on the intermolecular interactions between the molecular and ionic species in the liquid phase. NMR measurements for IL-acetone mixtures at different concentrations were also carried out. Quantum-chemical calculations by using molecular clusters of acetone and IL species were finally performed. These results provided additional evidence of the main role played by hydrogen bonding in the behavior of systems containing ILs and HB acceptor compounds, such as acetone.

Self-Associating Behavior of Acetone in Liquid Krypton.

Science.gov (United States)

De Beuckeleer, Liene I; Herrebout, Wouter A

2016-02-18

Acetone molecules are inclined to self-associate through dipole-dipole interactions because of their large dipole moment. Infrared spectroscopy of compounds dissolved in liquid noble gases supported by high level ab initio calculations allows investigating the self-associating behavior and determining the thermodynamical properties. In this study, infrared spectra of various concentrations of acetone dissolved in liquid krypton are recorded at constant temperature. Overlapping monomer and dimer spectra are separated by analyzing the obtained data sets with numerical methods based on least-squares fitting. Although acetone is known to self-associate, only a few spectral features have been presented in literature before. In this study, the application of new numerical approaches succeeds in resolving overlapping spectra and allows observing isolated acetone dimer absorption bands for the complete mid infrared spectrum. By use of data sets of spectra recorded at temperatures between 134 and 142 K, the experimental standard dimerization enthalpy was determined to be -10.8 kJ mol(-1). MP2/aug-cc-pVDZ calculations predicted a stacked and planar dimer geometry of which the stacked geometry is more stable. Combining MP2 energies and single point corrections involving CCSD(T) calculations and complete basis set extrapolations based on the MP2/aug-cc-pVDZ equilibrium geometry lead to complexation energy of -28.4 kJ mol(-1) for the stacked geometry and -15.1 kJ mol(-1) for the planar geometry. The corresponding values for the complexation enthalpies in solution, obtained by combining these values with corrections for thermal and solvent influences are -13.7 and -5.8 kJ mol(-1).

Conditioned Place Preference to Acetone Inhalation and the Effects on Locomotor Behavior and 18FDG Uptake

Energy Technology Data Exchange (ETDEWEB)

Pai, J.C.; Dewey, S.L.; Schiffer, W.; Lee, D.

2006-01-01

Acetone is a component in many inhalants that have been widely abused. While other solvents have addictive potential, such as toluene, it is unclear whether acetone alone contains addictive properties. The locomotor, relative glucose metabolism and abusive effects of acetone inhalation were studied in animals using the conditioned place preference (CPP) paradigm and [18F]2-fluorodeoxy-D-glucose (18FDG) imaging. The CPP apparatus contains two distinct conditioning chambers and a middle adaptation chamber, each lined with photocells to monitor locomotor activity. Adolescent Sprague-Dawley rats (n=16; 90-110 g) were paired with acetone in least preferred conditioning chamber, determined on the pretest day. The animals were exposed to a 10,000 ppm dose for an hour, alternating days with air. A CPP test was conducted after the 3rd, 6th and 12th pairing. In these same animals, the relative glucose metabolism effects were determined using positron emission tomography (PET) imaging with 18FDG. Following the 3rd pairing, there was a significant aversion to the acetone paired chamber (190.9 ± 13.7 sec and 241.7 ± 16.9 sec, acetone and air, respectively). After the 6th pairing, there was no significant preference observed with equal time spent in each chamber (222 ± 21 sec and 207 ± 20 sec, acetone and air-paired, respectively). A similar trend was observed after the 12th pairing (213 ± 21 sec and 221 ± 22 sec, acetone and air-paired, respectively). Locomotor analysis indicated a significant decrease (p<0.05) from air pairings to acetone pairings on the first and sixth pairings. The observed locomotor activity was characteristic of central nervous system (CNS) depressants, without showing clear abusive effects in this CPP model. In these studies, acetone vapors were not as reinforcing as other solvents, shown by overall lack of preference for the acetone paired side of the chamber. PET imaging indicated a regionally specific distribution of 18FDG uptake following

Purification and Characterization of the Acetone Carboxylase of Cupriavidus metallidurans Strain CH34

Science.gov (United States)

Rosier, Caroline; Leys, Natalie; Henoumont, Céline; Mergeay, Max

2012-01-01

Acetone carboxylase (Acx) is a key enzyme involved in the biodegradation of acetone by bacteria. Except for the Helicobacteraceae family, genome analyses revealed that bacteria that possess an Acx, such as Cupriavidus metallidurans strain CH34, are associated with soil. The Acx of CH34 forms the heterohexameric complex α2β2γ2 and can carboxylate only acetone and 2-butanone in an ATP-dependent reaction to acetoacetate and 3-keto-2-methylbutyrate, respectively. PMID:22492439

Decontamination of stethoscope membranes with chlorhexidine: Should it be recommended?

Science.gov (United States)

Álvarez, José A; Ruíz, Susana R; Mosqueda, Juan L; León, Ximena; Arreguín, Virginia; Macías, Alejandro E; Macias, Juan H

2016-11-01

To determine differences in the recontamination of stethoscope membranes after cleaning with chlorhexidine, triclosan, or alcohol. Experimental, controlled, blinded trial to determine differences in the bacterial load on stethoscope membranes. Membranes were cultured by direct imprint after disinfection with 70% isopropyl alcohol, 1% triclosan, or 1% chlorhexidine and normal use for 4 hours. As a baseline and an immediate effect control, bacterial load of membranes without disinfection and after 1 minute of disinfection with isopropyl alcohol was determined as well. Three hundred seventy cultures of in-use stethoscopes were taken, 74 from each arm. In the baseline arm the median growth was 10 CFU (interquartile range [IQR], 32-42 CFU); meanwhile, in the isopropyl alcohol immediate-effect arm it was 0 CFU (IQR, 0-0 CFU). In the arms cultured after 4 hours, a median growth of 8 CFU (IQR, 1-28 CFU) in the isopropyl alcohol arm, 4 CFU (IQR, 0-17 CFU) in the triclosan arm, and 0 CFU (IQR, 0-1 CFU) in the chlorhexidine arm were seen. No significant differences were observed between the bacterial load of the chlorhexidine arm (after 4 hours of use) and that of the isopropyl alcohol arm (after 1 minute without use) (Z= 2.41; P > .05). Chlorhexidine can inhibit recontamination of stethoscope membranes and its use could help avoid cross-infection. Copyright © 2016 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

A fully integrated standalone portable cavity ringdown breath acetone analyzer

Science.gov (United States)

Sun, Meixiu; Jiang, Chenyu; Gong, Zhiyong; Zhao, Xiaomeng; Chen, Zhuying; Wang, Zhennan; Kang, Meiling; Li, Yingxin; Wang, Chuji

2015-09-01

Breath analysis is a promising new technique for nonintrusive disease diagnosis and metabolic status monitoring. One challenging issue in using a breath biomarker for potential particular disease screening is to find a quantitative relationship between the concentration of the breath biomarker and clinical diagnostic parameters of the specific disease. In order to address this issue, we need a new instrument that is capable of conducting real-time, online breath analysis with high data throughput, so that a large scale of clinical test (more subjects) can be achieved in a short period of time. In this work, we report a fully integrated, standalone, portable analyzer based on the cavity ringdown spectroscopy technique for near-real time, online breath acetone measurements. The performance of the portable analyzer in measurements of breath acetone was interrogated and validated by using the certificated gas chromatography-mass spectrometry. The results show that this new analyzer is useful for reliable online (online introduction of a breath sample without pre-treatment) breath acetone analysis with high sensitivity (57 ppb) and high data throughput (one data per second). Subsequently, the validated breath analyzer was employed for acetone measurements in 119 human subjects under various situations. The instrument design, packaging, specifications, and future improvements were also described. From an optical ringdown cavity operated by the lab-set electronics reported previously to this fully integrated standalone new instrument, we have enabled a new scientific tool suited for large scales of breath acetone analysis and created an instrument platform that can even be adopted for study of other breath biomarkers by using different lasers and ringdown mirrors covering corresponding spectral fingerprints.

A fully integrated standalone portable cavity ringdown breath acetone analyzer.

Science.gov (United States)

Sun, Meixiu; Jiang, Chenyu; Gong, Zhiyong; Zhao, Xiaomeng; Chen, Zhuying; Wang, Zhennan; Kang, Meiling; Li, Yingxin; Wang, Chuji

2015-09-01

Breath analysis is a promising new technique for nonintrusive disease diagnosis and metabolic status monitoring. One challenging issue in using a breath biomarker for potential particular disease screening is to find a quantitative relationship between the concentration of the breath biomarker and clinical diagnostic parameters of the specific disease. In order to address this issue, we need a new instrument that is capable of conducting real-time, online breath analysis with high data throughput, so that a large scale of clinical test (more subjects) can be achieved in a short period of time. In this work, we report a fully integrated, standalone, portable analyzer based on the cavity ringdown spectroscopy technique for near-real time, online breath acetone measurements. The performance of the portable analyzer in measurements of breath acetone was interrogated and validated by using the certificated gas chromatography-mass spectrometry. The results show that this new analyzer is useful for reliable online (online introduction of a breath sample without pre-treatment) breath acetone analysis with high sensitivity (57 ppb) and high data throughput (one data per second). Subsequently, the validated breath analyzer was employed for acetone measurements in 119 human subjects under various situations. The instrument design, packaging, specifications, and future improvements were also described. From an optical ringdown cavity operated by the lab-set electronics reported previously to this fully integrated standalone new instrument, we have enabled a new scientific tool suited for large scales of breath acetone analysis and created an instrument platform that can even be adopted for study of other breath biomarkers by using different lasers and ringdown mirrors covering corresponding spectral fingerprints.

Change of Exhaled Acetone Concentration in a Diabetic Patient with Acute Decompensated Heart Failure.

Science.gov (United States)

Yokokawa, Tetsuro; Ichijo, Yasuhiro; Houtsuki, Yu; Matsumoto, Yoshiyuki; Oikawa, Masayoshi; Yoshihisa, Akiomi; Sugimoto, Koichi; Nakazato, Kazuhiko; Suzuki, Hitoshi; Saitoh, Shu-Ichi; Shimouchi, Akito; Takeishi, Yasuchika

2017-10-21

In heart failure patients, exhaled acetone concentration, a noninvasive biomarker, is increased according to heart failure severity. Moreover, exhaled acetone concentration is also known to be affected by diabetes mellitus. However, there have been no reports on exhaled acetone concentration in heart failure patients with diabetes mellitus. A 77-year old man was admitted to our hospital with acute decompensated heart failure and atrioventricular block. He had controlled diabetes mellitus under insulin treatment with hemoglobin A1c of 6.5%. He underwent treatment of diuretics and permanent pacemaker implantation. His condition improved and he was discharged at Day 12. Due to the heart failure improvement, his levels of exhaled acetone concentration decreased from 1.623 ppm at admission to 0.664 ppm at discharge. This is the first report to reveal a change of exhaled acetone concentration in a diabetic patient with acute decompensated heart failure.

Sensing behavior of acetone vapors on TiO_2 nanostructures — application of density functional theory

Directory of Open Access Journals (Sweden)

V. Nagarajan

2017-12-01

Full Text Available The electronic properties of TiO_2 nanostructure are explored using density functional theory. The adsorption properties of acetone on TiO_2 nanostructure are studied in terms of adsorption energy, average energy gap variation and Mulliken charge transfer. The density of states spectrum and the band structure clearly reveals the adsorption of acetone on TiO_2 nanostructures. The variation in the energy gap and changes in the density of charge are observed upon adsorption of acetone on n-type TiO_2 base material. The results of DOS spectrum reveal that the transfer of electrons takes place between acetone vapor and TiO_2 base material. The findings show that the adsorption property of acetone is more favorable on TiO_2 nanostructure. Suitable adsorption sites of acetone on TiO_2 nanostructure are identified at atomistic level. From the results, it is confirmed that TiO_2 nanostructure can be efficiently utilized as a sensing element for the detection of acetone vapor in a mixed environment.

(Ternary liquid + liquid) equilibria for (water + acetone + α-pinene, or β-pinene, or limonene) mixtures

International Nuclear Information System (INIS)

Li Xiaoli; Tamura, Kazuhiro

2010-01-01

(Ternary liquid + liquid) equilibria (tie-lines) of (water + acetone + α-pinene) at T = (288.15, 298.15, and 308.15) K and (water + acetone + β-pinene, or limonene) at T = 298.15 K have been measured. The experimental (ternary liquid + liquid) equilibrium data have been correlated successfully by the original UNIQUAC and modified UNIQUAC models. The modified UNIQUAC model reproduced accurately the experimental results for the (water + acetone + α-pinene) system at all the temperatures but fairly agreed with the experimental data for the (water + acetone + β-pinene, or limonene) systems.

A two-stage combined trickle bed reactor/biofilter for treatment of styrene/acetone vapor mixtures.

Science.gov (United States)

Vanek, Tomas; Halecky, Martin; Paca, Jan; Zapotocky, Lubos; Gelbicova, Tereza; Vadkertiova, Renata; Kozliak, Evguenii; Jones, Kim

2015-01-01

Performance of a two-stage biofiltration system was investigated for removal of styrene-acetone mixtures. High steady-state acetone loadings (above C(in)(Ac) = 0.5 g.m(-3) corresponding to the loadings > 34.5 g.m(-3).h(-1)) resulted in a significant inhibition of the system's performance in both acetone and styrene removal. This inhibition was shown to result from the acetone accumulation within the upstream trickle-bed bioreactor (TBR) circulating mineral medium, which was observed by direct chromatographic measurements. Placing a biofilter (BF) downstream to this TBR overcomes the inhibition as long as the biofilter has a sufficient bed height. A different kind of inhibition of styrene biodegradation was observed within the biofilter at very high acetone loadings (above C(in)(Ac) = 1.1 g.m(-3) or 76 g.m(-3).h(-1) loading). In addition to steady-state measurements, dynamic tests confirmed that the reactor overloading can be readily overcome, once the accumulated acetone in the TBR fluids is degraded. No sizable metabolite accumulation in the medium was observed for either TBR or BF. Analyses of the biodegradation activities of microbial isolates from the biofilm corroborated the trends observed for the two-stage biofiltration system, particularly the occurrence of an inhibition threshold by excess acetone.

Kinetic Model of Resin-Catalyzed Decomposition of Acetone Cyanohydrin in Organic Solvent%有机溶剂中树脂催化丙酮氰醇分解反应的动力学模型

Institute of Scientific and Technical Information of China (English)

章亭洲; 杨立荣; 朱自强; 吴坚平

2003-01-01

Decomposition of acetone cyanohydrin is the first-step reaction for preparing (S)-α-cyano-3-phenoxybenzyl alcohol (CPBA) by the one-pot method in organic media. Considering the compatibility of bio-catalysts with chemical catalysts and the successive operation in the bioreactor, anion exchange resin (D301) wasused as catalyst for this reaction. External diffusion limitation was excluded by raising rotational speed to higherthan 190r@min-1 in both solvents. Internal diffusion limitation was verified to be insignificant in this reactionsystem. The effect of acetone cyanohydrin concentration on the reaction was also investigated. An intrinsic kineticmodel was proposed when the mass transfer limitation was excluded, and the average deviation of the model is10.5%.

Synthesis and Characterization of Poly (ether imide)s Containing Phthalazinone and Isopropyl Moieties

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

A novel poly(ether imide)s containing phthalazinone and isopropyl moieties derived from 2-(4-aminophenyl)-4-[4-(4-aminophenoxy)phenyl]-phthalazin-l-one and bisphenol-A diphthalic anhydride was synthesized by one-step solution condensation polymerization in m-cresol. The polymer was characterized by FTIR, NMR, molecular weights, glass transition temperature,thermal degradation temperature and WAXD.

Skin barrier disruption by acetone: observations in a hairless mouse skin model

NARCIS (Netherlands)

Rissmann, R.; Oudshoorn, M.H.M.; Hennink, W.E.; Ponec, M.; Bouwstra, J.A.

2009-01-01

To disrupt the barrier function of the skin, different in vivo methods have been established, e.g., by acetone wiping or tape-stripping. In this study, the acetone-induced barrier disruption of hairless mice was investigated in order to establish a reliable model to study beneficial, long-term

Combustion synthesized hierarchically porous WO{sub 3} for selective acetone sensing

Energy Technology Data Exchange (ETDEWEB)

Dong, Chengjun; Liu, Xu; Guan, Hongtao; Chen, Gang; Xiao, Xuechun [Department of Materials Science and Engineering, Yunnan University, 650091, Kunming (China); Djerdj, Igor [Ruđer Bošković Institute, Bijenička 54, 10000, Zagreb (Croatia); Wang, Yude, E-mail: ydwang@ynu.edu.cn [Department of Materials Science and Engineering, Yunnan University, 650091, Kunming (China); Yunnan Province Key Lab of Mico-Nano Materials and Technology, Yunnan University, 650091, Kunming (China)

2016-12-01

An easy, inexpensive combustion route was designed to synthesize hierarchically porous WO{sub 3}. The tungsten source was fresh peroxiotungstic acid by dissolving tungsten powder into hydrogen peroxide. To promote the combustion reaction, a combined fuel of both glycine and hydrazine hydrate was used. The microstructure was well-connected pores comprised of subunit nanoparticles. Upon exposing towards acetone gas, the porous WO{sub 3} based sensor exhibits high gas response, rapid response and recovery, and good selectivity in the range of 5–1000 ppm under working temperature of 300 °C. This excellent sensing performance was plausibly attributed to the porous morphology, which hence provides more active sites for the gas molecules' reaction. - Graphical abstract: Hierarchically porous WO{sub 3} synthesized by combustion process exhibits high gas response, rapid response and recovery, and excellent selectivity for acetone, making it to be promising candidates for practical detectors for acetone. - Highlights: • Hierarchically porous WO{sub 3} synthesized by combustion process. • Hierarchically porous WO{sub 3} exhibits high gas response and excellent selectivity for acetone. • The excellent sensing property was plausibly attributed to the porous morphology.

Gadolinium-, Calcium-, copper- and zirc complexes with riboflavin in acetone and acetonitrile

International Nuclear Information System (INIS)

Lugina, L.N.; Romanenko, V.I.; Davidenko, N.K.

1983-01-01

Using the methods of solubility and spectrophotometry, stability copstants Of complexes RFMSSUp(n+) (RF=riboflavin, Mnsup(n+)=Cdsup(3+), Ca 2+ , Cu 2+ and Zn 2+ ) in acetone and acetonitrile against the background of 1 mol/l LiClO 4 x3H 2 O have been determined. It was found that stability of copper and zinc complexes with riboflavin in acetone is higher than in acetonitrile, whereas the stability of gadolinium and calcium complexes, on the contrary, is higher in acetonitrile than in acetone. It is shown that the character of the absorption spectrum change of riboflavin in complexing with metal ions depends on the nature of coordinating cation

Application of finite inverse gas chromatography in hypromellose acetate succinate-water-acetone systems.

Science.gov (United States)

Chiu, Sheng-Wei; Sturm, Derek R; Moser, Justin D; Danner, Ronald P

2016-09-30

A modification of a GC was developed to investigate both infinitely dilute and finite concentrations of solvents in polymers. Thermodynamic properties of hypromellose acetate succinate (HPMCAS-L)-acetone-water systems are important for the optimization of spray-drying processes used in pharmaceutical manufacturing of solid dispersion formulations. These properties, at temperatures below the glass transition temperature, were investigated using capillary column inverse gas chromatography (CCIGC). Water was much less soluble in the HPMCAS-L than acetone. Experiments were also conducted at infinitely dilute concentrations of one of the solvents in HPMCAS-L that was already saturated with the other solvent. Overall the partitioning of the water was not significantly affected by the presence of either water or acetone in the polymer. The acetone partition coefficient decreased as either acetone or water was added to the HPMCAS-L. A representation of the HPMCAS-L structure in terms of UNIFAC groups has been developed. With these groups, the UNIFAC-vdw-FV model did a reasonable job of predicting the phase equilibria in the binary and ternary systems. The Flory-Huggins correlation with fitted interaction parameters represented the data well. Copyright © 2016 Elsevier B.V. All rights reserved.

Oscillatory bromate-oxalic acid-Ce-acetone-sulfuric acid reaction, in CSTR

International Nuclear Information System (INIS)

Pereira, Janaina A.M.; Faria, Roberto B.

2004-01-01

Periodic oscillations were observed for the first time, in a CSTR, in the system bromate-oxalic acid-Ce(IV)-acetone-sulfuric acid, in a CSTR. A reaction between Ce(IV) and acetone, until now not described in the literature and occurring before the addition of the reagents to the reactor, was identified as a decisive factor for the appearing of the regular oscillations. (author)

Theoretical Kinetic Study of the Unimolecular and H-Assisted Keto-Enol Tautomerism Propen-2-ol ↔Acetone. Pressure Effects and Implications in the Pyrolysis and Oxidation of tert- And 2-Butanol

KAUST Repository

Grajales Gonzalez, Edwing Javier

2018-05-01

The need for renewable and cleaner sources of energy has made biofuels an interesting alternative to fossil fuels, especially in the case of butanol isomers, with their favorable blend properties and low hygroscopicity. Although C4 alcohols are prospective fuels, some key reactions governing their pyrolysis and combustion have not been adequately studied, leading to incomplete kinetic models. Butanol reactions kinetics is poorly understood. Specifically, the unimolecular and H-assisted tautomerism of propen-2-ol to acetone, which are included in butanol combustion kinetic models, are assigned rate parameters based on the analogous unimolecular tautomerism vinyl alcohol ↔ acetaldehyde and H addition to the double bound of iso-butene, respectively. In an attempt to update current kinetic models for tert- and 2-butanol, a theoretical kinetic study of the unimolecular and H-assisted tautomerism, i-C3H5OH⟺CH3COCH3 and i-C3H5OH+Ḣ⟺CH3COCH3+Ḣ, was carried out by means of CCSD(T,FULL)/aug-cc-pVTZ//CCSD(T)/6-31+G(d,p) and CCSD(T)/aug-cc-pVTZ//M062X/cc-pVTZ ab initio calculations, respectively. For H-assisted tautomerism, the reaction takes place in two consecutive steps: i-C3H5OH+Ḣ⟺CH3ĊOHCH3 and CH3ĊOHCH3⟺CH3COCH3+Ḣ. Multistructural torsional anharmonicity and variational transition state theory were considered in a wide temperature and pressure range (200 K – 3000 K, 0.1 kPa – 108 kPa). It was observed that decreasing pressure leads to a decrease in rate constants, describing the expected falloff behavior for both isomerizations. Results for unimolecular tautomerism differ from vinyl alcohol ↔ acetaldehyde analogue reactions, which shows lower rate constant values. Tunneling turned out to be important, especially at low temperatures. Accordingly, pyrolysis simulations in a batch reactor for tert- and 2-butanol with computed unimolecular rate constants showed important differences in comparison with previous results, such as larger acetone yield and

The Hydrolysis of Di-Isopropyl Methylphosphonate in Ground Water

Energy Technology Data Exchange (ETDEWEB)

Sega, G.A., Tomkins, B.A., Griest, W.H., Bayne, C.K.

1997-12-31

Di-isopropyl methylphosphonate (DIMP) is a byproduct from the manufacture of the nerve agent Sarin. The persistence of DIMP in the ground water is an important question in evaluating the potential environmental impacts of DIMP contamination. The half-life of DIMP in ground water at 10 deg C was estimated to be 500 years with a 95% confidence interval of 447 to 559 years from measurements of the hydrolysis rates at temperatures between 70 to 98 deg C.Extrapolation of the kinetics to 10 deg C used the Arrhenius equation, and calculation of the half-life assumed first-order kinetics. Inorganic phosphate was not detected.

Kinetic features of cadmium electrodeposition in iodide water-acetone electrolytes

International Nuclear Information System (INIS)

Kuznetsov, V.V.; Skibina, L.M.; Khalikov, R.R.

2006-01-01

Based on the data of chronopotentiometric, galvanostatic, potentiodynamic, and impedance measurements, the composition of aqueous acetone electrolyte is studied for its effect on the rate of cadmium(II) electroreduction in iodide media. The adsorption of I - ions on the cadmium cathode surface is shown to depend on the interaction mechanism between the components of water-acetone mixtures. During a competitive adsorption of anions and organic solvent molecules, this affects the mechanism and the rate of electrodeposition and also the coating quality [ru

Reported Adverse Health Effects in Children from Ingestion of Alcohol-Based Hand Sanitizers - United States, 2011-2014.

Science.gov (United States)

Santos, Cynthia; Kieszak, Stephanie; Wang, Alice; Law, Royal; Schier, Joshua; Wolkin, Amy

2017-03-03

Hand sanitizers are effective and inexpensive products that can reduce microorganisms on the skin, but ingestion or improper use can be associated with health risks. Many hand sanitizers contain up to 60%-95% ethanol or isopropyl alcohol by volume, and are often combined with scents that might be appealing to young children. Recent reports have identified serious consequences, including apnea, acidosis, and coma in young children who swallowed alcohol-based (alcohol) hand sanitizer (1-3). Poison control centers collect data on intentional and unintentional exposures to hand sanitizer solutions resulting from various routes of exposure, including ingestion, inhalation, and dermal and ocular exposures. To characterize exposures of children aged ≤12 years to alcohol hand sanitizers, CDC analyzed data reported to the National Poison Data System (NPDS).* The major route of exposure to both alcohol and nonalcohol-based (nonalcohol) hand sanitizers was ingestion. The majority of intentional exposures to alcohol hand sanitizers occurred in children aged 6-12 years. Alcohol hand sanitizer exposures were associated with worse outcomes than were nonalcohol hand sanitizer exposures. Caregivers and health care providers should be aware of the potential dangers associated with hand sanitizer ingestion. Children using alcohol hand sanitizers should be supervised and these products should be kept out of reach from children when not in use.

Oxidative kinetic resolution of racemic alcohols catalyzed by chiral ferrocenyloxazolinylphosphine-ruthenium complexes.

Science.gov (United States)

Nishibayashi, Yoshiaki; Yamauchi, Akiyoshi; Onodera, Gen; Uemura, Sakae

2003-07-25

Oxidative kinetic resolution of racemic secondary alcohols by using acetone as a hydrogen acceptor in the presence of a catalytic amount of [RuCl(2)(PPh(3))(ferrocenyloxazolinylphosphine)] (2) proceeds effectively to recover the corresponding alcohols in high yields with an excellent enantioselectivity. When 1-indanol is employed as a racemic alcohol, the oxidation proceeds quite smoothly even in the presence of 0.0025 mol % of the catalyst 2 to give an optically active 1-indanol in good yield with high enantioselectivity (up to 94% ee), where turnover frequency (TOF) exceeds 80,000 h(-1). From a practical viewpoint, the kinetic resolution is investigated in a large scale, optically pure (S)-1-indanol (75 g, 56% yield, >99% ee) being obtained from racemic 1-indanol (134 g) by employing this kinetic resolution method twice.

Thermodynamic analysis of acetone sensing in Pd/AlGaN/GaN heterostructure Schottky diodes at low temperatures

International Nuclear Information System (INIS)

Das, Subhashis; Majumdar, Shubhankar; Kumar, Rahul; Ghosh, Saptarsi; Biswas, Dhrubes

2016-01-01

An AlGaN/GaN heterostructure based metal–semiconductor–metal symmetrically bi-directional Schottky diode sensor structure has been employed to investigate acetone sensing and to analyze thermodynamics of acetone adsorption at low temperatures. The AlGaN/GaN heterostructure has been grown by plasma-assisted molecular beam epitaxy on Si (111). Schottky diode parameters at different temperatures and acetone concentrations have been extracted from I–V characteristics. Sensitivity and change in Schottky barrier height have been studied. Optimum operating temperature has been established. Coverage of acetone adsorption sites at the AlGaN surface and the effective equilibrium rate constant of acetone adsorption have been explored to determine the endothermic nature of acetone adsorption enthalpy.

Theoretical investigation of molecular structure and vibrational spectra of 4,5-bis-(2-isopropyl-5- methylphenoxy) phthalonitrile molecule

International Nuclear Information System (INIS)

Avci, D.

2005-01-01

The molecular geometry and vibrational frequencies of 4,5-bis-(2-isopropyl-5- methylphenoxy) phthalonitrile in the ground state have been calculated using the Hartree- Fock (HF) and density functional method (B3LYP) with 6-31G(d) basis set. The optimized geometric bond lengths and bond angles obtained by using HF and DFT (B3LYP) show the best agreement with the experimental data. Comparison of the observed fundamental vibrational frequencies of 4,5-bis-(2-isopropyl-5-methylphenoxy) phthalonitrile with calculated results by density functional B3LYP and Hartree-Fock methods indicate that B3LYP is superior to the scaled Hartree-Fock approach for molecular vibrational problems

(Liquid + liquid) equilibria for (water + 1-propanol or acetone + β-citronellol) at different temperatures

International Nuclear Information System (INIS)

Li, Hengde; Han, Yongtao; Huang, Cheng; Yang, Chufen

2015-01-01

Graphical abstract: (Liquid + liquid) equilibrium data for systems composed of β-citronellol and aqueous 1-propanol or acetone are presented. Distribution ratios of 1-propanol and acetone in the mixtures are examined. The effect of the temperature on the ternary (liquid + liquid) equilibria is evaluated and discussed. - Highlights: • Ternary (liquid + liquid) equilibria containing β-citronellol are presented. • Distribution ratios of 1-propanol and acetone in the mixtures are examined. • The effect on the temperature of the systems is evaluated and discussed. - Abstract: On this paper, experimental (liquid + liquid) equilibrium (LLE) results are presented for systems composed of β-citronellol and aqueous 1-propanol or acetone. To evaluate the phase separation properties of β-citronellol in aqueous mixtures, LLE values for the ternary systems (water + 1-propanol + β-citronellol) and (water + acetone + β-citronellol) were determined with a tie-line method at T = (283.15, 298.15, and 313.15 ± 0.02) K and atmospheric pressure. The reliability of the experimental tie-lines was verified by the Hand and Bachman equations. Ternary phase diagrams, distribution ratios of 1-propanol and acetone in the mixtures are shown. The effect of the temperature on the ternary (liquid + liquid) equilibria was examined and discussed. The experimental LLE values were satisfactorily correlated by extended UNIQUAC and modified UNIQUAC models

Photodissociation of the acetone cation at 355 nm using the velocity imaging technique

Science.gov (United States)

Jackson, William M.; Xu, Dadong

2000-09-01

Photodissociation of acetone cations, CH3COCH3+, at 355 nm has been studied by means of the ion velocity imaging technique. Acetone cations are produced via direct photoionization of a supersonic beam of acetone at 118 nm generated by frequency tripling the 355 nm laser. Only the acetyl cation, CH3CO+, could be detected as a dissociation product in the time-of-flight mass spectrometer. The acetyl ion signal depends upon the fifth power of the 355 nm laser energy, while the acetone ion signal depends upon the third power. This suggests that the fragment ion is produced via two-photon absorption of 355 nm photons by the acetone cation. The total translational energy distribution and angular distribution of acetyl cation were derived from the 2D images of CH3CO+ for the reaction CH3COCH3++2hν355nm→CH3CO++CH3*. The translational energy distribution suggests that methyl radicals are produced in two electronically excited states, the Rydberg 3s 1 2A1' and the valence 1 2A″ states. The anisotropy parameter β shows that the Rydberg state is formed via a perpendicular excitation and the valence state via a parallel transition.

Phytochemical screening and study of antioxidant, antimicrobial, antidiabetic, anti-inflammatory and analgesic activities of extracts from stem wood of Pterocarpus marsupium Roxburgh.

Science.gov (United States)

Pant, Dipak Raj; Pant, Narayan Dutt; Saru, Dil Bahadur; Yadav, Uday Narayan; Khanal, Dharma Prasad

2017-01-01

The main aims of the study were to evaluate the phytochemical constituents and to study the antioxidant, antimicrobial, antidiabetic, anti-inflammatory, and analgesic activities of extracts from stem wood of Pterocarpus marsupium . Ethanol, acetone and isopropyl alcohol (IPA) (1:1) extracts of stem wood of P. marsupium were subjected to phytochemical screening and analysis of biological activities from August 2015 to January 2016. The antioxidant assay was carried out using 2, 2-diphenyl-1-picrylhydrazyl scavenging method, antimicrobial activity testing by cup diffusion method, antidiabetic test evaluation by oral glucose tolerance test in mice, anti-inflammatory effect was evaluated by hind paw edema method in mice and analgesic test evaluation by a chemical writhing method in mice. The results of the study revealed that P. marsupium is a source of various phytoconstituents such as alkaloids, glycosides, saponins, tannins, proteins, carbohydrates, cardiac glycosides, flavonoids, and terpenoids. Both the acetone and IPA extract as well as the ethanol extract of stem wood of P. marsupium exhibited a dose-dependent antioxidant activity. Acetone and IPA extract showed antibacterial activity against Gram-positive bacteria, while the ethanolic extract was found to possess antidiabetic activity. The antidiabetic activity of the extract was found to be time and dose-dependent. Similarly, the acetone and IPA extract was found to have anti-inflammatory activity, which was also time and dose-dependent. Furthermore, the ethanolic extract showed analgesic activity, which was dose-dependent. The ethanolic extract was found to be nontoxic. Thus, this study laid sufficient background for the further research on extracts from stem wood of P. marsupium for identification, subsequent purification and isolation of compounds having antibacterial, antidiabetic, anti-inflammatory, and analgesic activities.

Poly aniline Nano fiber as Modified Cladding for Optical Fiber Sensor to Detect Acetone Vapor

International Nuclear Information System (INIS)

Akhiruddin maddu; Ahmad aminuddin; Setyanto Tri Wahyudi; Hamdani Zain

2008-01-01

In this research, we used poly aniline nano fiber as modified cladding material for a fiber optic sensor system to detect the acetone vapor. The sensor was designed based on variation of evanescent field absorption on the core-modified cladding interface when exposed with varied acetone vapor. Poly aniline nano fiber synthesized by interfacial polymerization was coated onto the un-cladded core and acts as sensing element. Response of the fiber optic sensor was investigated by measuring the transmission light intensity via fiber optic sensor system while exposed with acetone vapor. Based on the sensor response curve, it is obtained a very fast response time of 30 s and recovery time of 10 s. The fiber optic sensor also exhibits a good reversibility and repeatability. Sensitivity of the sensor to variation of acetone vapor pressure was obtained 1.25 %/mmHg, that means the transmission intensity of the sensor changes 1.25 % for acetone vapor change of 1 mmHg. (author)

Y-Doped ZnO Nanorods by Hydrothermal Method and Their Acetone Gas Sensitivity

Directory of Open Access Journals (Sweden)

Peng Yu

2013-01-01

Full Text Available Pure and yttrium- (Y- doped (1 at%, 3 at%, and 7 at% ZnO nanorods were synthesized using a hydrothermal process. The crystallography and microstructure of the synthesized samples were characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM, and energy dispersive X-ray spectroscopy (EDX. Comparing with pure ZnO nanorods, Y-doped ZnO exhibited improved acetone sensing properties. The response of 1 at% Y-doped ZnO nanorods to 100 ppm acetone is larger than that of pure ZnO nanorods. The response and recovery times of 1 at% Y-doped ZnO nanorods to 100 ppm acetone are about 30 s and 90 s, respectively. The gas sensor based on Y-doped ZnO nanorods showed good selectivity to acetone in the interfere gases of ammonia, benzene, formaldehyde, toluene, and methanol. The formation mechanism of the ZnO nanorods was briefly analyzed.

Upper Bound for Neutron Emission from Sonoluminescing Bubbles in Deuterated Acetone

International Nuclear Information System (INIS)

Camara, C. G.; Putterman, S. J.; Hopkins, S. D.; Suslick, K. S.

2007-01-01

An experimental search for nuclear fusion inside imploding bubbles of degassed deuterated acetone at 0 degree sign C driven by a 15 atm sound field and seeded with a neutron generator reveals an upper bound that is a factor of 10 000 less than the signal reported by Taleyarkhan et al. The strength of our upper bound is limited by the weakness of sonoluminescence, which we ascribe to the relatively high vapor pressure of acetone

Damages induced in lambda phage DNA by enzyme-generated triplet acetone

International Nuclear Information System (INIS)

Menck, C.F.; Cabral Neto, J.B.; Gomes, R.A.; Faljoni-Alario, A.

1985-01-01

Exposure of lambda phage to triplet acetone, generated during the aerobic oxidation of isobutanal by peroxidase, leads to genome lesions. The majority of these lesions are detected as DNA single-strand breaks only in alkaline conditions, so true breaks were not observed. Also, no sites sensitive to UV-endonuclease from Micrococcus luteus were found in DNA from treated phage. The participation of triplet acetone in the generation of such DNA damage is discussed. (Author) [pt

Pyrolysis and liquefaction of acetone and mixed acetone/ tetralin swelled Mukah Balingian Malaysian sub-bituminous coal-The effect on coal conversion and oil yield

International Nuclear Information System (INIS)

Mohd Pauzi Abdullah; Mohd Azlan Mohd Ishak; Khudzir Ismail

2008-01-01

The effect of swelling on Mukah Balingian (MB) Malaysian sub-bituminous coal macrostructure was observed by pyrolysing the swelled coal via thermogravimetry under nitrogen at ambient pressure. The DTG curves of the pyrolyzed swelled coal samples show the presence of evolution peaks at temperature ranging from 235 - 295 degree Celsius that are due to releasing of light molecular weight hydrocarbons. These peaks, however, were not present in the untreated coal, indicating some changes in the coal macrostructure has occurred in the swelled coal samples. The global pyrolysis kinetics for coal that follows the first-order decomposition reaction was used to evaluate the activation energy of the pyrolyzed untreated and swelled coal samples. The results thus far have shown that the activation energy for the acetone and mixed acetone/ tetralin-swelled coal samples exhibit lower values than untreated coal, indicating less energy is required during the pyrolysis process due to the weakening of the coal-coal macromolecular interaction network. Moreover, liquefaction on the swelled coal samples that was carried out at temperatures ranging from 360 to 450 degree Celsius at 4 MPa of nitrogen pressure showed the enhancement of the coal conversion and oil yield at temperature of 420 degree Celsius, with retrogressive reaction started to dominate at higher temperature as indicated by decreased and increased in oil yield and high molecular weight pre-asphaltene, respectively. These observations suggest that the solvent swelling pre-treatment using acetone and mixed acetone/ tetralin can improve the coal conversion and oil yields at less severe liquefaction condition. (author)

Mobility and molecular ions of dimethyl methyl phosphonate, methyl salicylate and acetone

Science.gov (United States)

Nowak, D. M.

1983-06-01

The mobilities of positive and negative reactant ions are reported for (H2O)nH(+); (H2O)2O2 and (H2O)2CO3(-) ion clusters. The formation of positive DMMP monomer and dimer is reported, and equilbria molecular reactions are reported. Acetone is reported as forming a dimer at 81 ppb with a reduced mobility (K sub o) of 1.82, Methyl salicylate is shown to form a protonated and hydrated positive monomer. Mixtures of DMMP and methyl salicylate with acetone showed a substantial change in DMMP ion clustering and little or no change in the methyl salicylate mobility spectra. Negative ions were not observed for DMMP, methyl salicylate, acetone and the mixtures under the conditions reported.

Ultratrace Measurement of Acetone from Skin Using Zeolite: Toward Development of a Wearable Monitor of Fat Metabolism.

Science.gov (United States)

Yamada, Yuki; Hiyama, Satoshi; Toyooka, Tsuguyoshi; Takeuchi, Shoji; Itabashi, Keiji; Okubo, Tatsuya; Tabata, Hitoshi

2015-08-04

Analysis of gases emitted from human skin and contained in human breath has received increasing attention in recent years for noninvasive clinical diagnoses and health checkups. Acetone emitted from human skin (skin acetone) should be a good indicator of fat metabolism, which is associated with diet and exercise. However, skin acetone is an analytically challenging target because it is emitted in very low concentrations. In the present study, zeolite was investigated for concentrating skin acetone for subsequent semiconductor-based analysis. The adsorption and desorption characteristics of five zeolites with different structures and those hydrophobicities were compared. A hydrophobic zeolite with relatively large pores (approximately 1.6 times larger than the acetone molecule diameter) was the best concentrator of skin acetone among the zeolites tested. The concentrator developed using zeolite was applied in a semiconductor-based gas sensor in a simulated mobile environment where the closed space was frequently collapsed to reflect the twisting and elastic movement of skin that would be encountered in a wearable device. These results could be used to develop a wearable analyzer for skin acetone, which would be a powerful tool for preventing and alleviating lifestyle-related diseases.

LET effect on irradiation of hydroxyphthal imide in alcohol solutions

International Nuclear Information System (INIS)

Nakagawa, S.; Murakami, T.

2005-01-01

Hydroxyphthalimide(C 6 H 4 (CO) 2 -NOH) was irradiated with C ion (290MeV/u) in isopropyl alcohol, methanol, ethanol, and acetonitrile. LET was 13.2 and 26.5 keV/m. Dose was 5 and 10 kGy. A little amount of phthalimide was produced. The G value of the production of phthalimide by ion irradiation was less than that by -irradiation except for in methanol. In methanol solution, the production rate of phthalimide increased with increasing the value of LET. The amount of the substitution for C 6 H 4 (CO) 2 -NOD in methanol-d decreased by ion irradiation. These results suggest that the reaction mechanism in ion irradiation is different from -irradiation. (author)

Biofiltration of mixtures of gas-phase styrene and acetone with the fungus Sporothrix variecibatus

International Nuclear Information System (INIS)

Rene, Eldon R.; Spackova, Radka; Veiga, Maria C.; Kennes, Christian

2010-01-01

The biodegradation performance of a biofilter, inoculated with the fungus Sporothrix variecibatus, to treat gas-phase styrene and acetone mixtures under steady-state and transient conditions was evaluated. Experiments were carried out by varying the gas-flow rates (0.05-0.4 m 3 h -1 ), leading to empty bed residence times as low as 17.1 s, and by changing the concentrations of gas-phase styrene (0.01-6.3 g m -3 ) and acetone (0.01-8.9 g m -3 ). The total elimination capacities were as high as 360 g m -3 h -1 , with nearly 97.5% removal of styrene and 75.6% for acetone. The biodegradation of acetone was inhibited by the presence of styrene, while styrene removal was affected only slightly by the presence of acetone. During transient-state experiments, increasing the overall pollutant load by almost 3-fold, i.e., from 220 to 600 g m -3 h -1 , resulted in a sudden drop of removal efficiency (>90-70%), but still high elimination capacities were maintained. Periodic microscopic observations revealed that the originally inoculated Sporothrix sp. remained present in the reactor and actively dominant in the biofilm.

Study of the exhaled acetone in type 1 diabetes using quantum cascade laser spectroscopy.

Science.gov (United States)

Reyes-Reyes, Adonis; Horsten, Roland C; Urbach, H Paul; Bhattacharya, Nandini

2015-01-06

The acetone concentration exhaled in the breath of three type 1 diabetes patients (two minors and one adult) and one healthy volunteer is studied using a quantum cascade laser-based spectroscopic system. Using the acetone signature between 1150 and 1250 cm(-1) and a multiline fitting method, the concentration variations on the order of parts per billion by volume were measured. Blood glucose and ketone concentrations in blood measurements were performed simultaneously to study their relation with acetone in exhaled breath. We focus on personalized studies to better understand the role of acetone in diabetes. For each volunteer, we performed a series of measurements over a period of time, including overnight fastings of 11 ± 1 h and during ketosis-hyperglycemia events for the minors. Our results highlight the importance of performing personalized studies because the response of the minors to the presence of ketosis was consistent but unique for each individual. Also, our results emphasize the need for performing more studies with T1D minors, because the acetone concentration in the breath of the minors differs, with respect to those reported in the literature, which are based on adults.

Solvents (butanol, acetone, and ethanol). [USSR Patent

Energy Technology Data Exchange (ETDEWEB)

Yarovenko, V L; Nakhmanovich, B M

1963-07-17

The method involves use of carbohydrate-containing plant raw-material, e.g. hydrolyzates of corn cob and pulp. The material is subjected to fermentation with acetone-butanol bacteria with addition of starch-industry wastes as source of proteins (gluten and gluten-containing water) and nutrient salts.

Communication: Potentials of mean force study of ionic liquid ion pair aggregation in polar covalent molecule solvents

Science.gov (United States)

Bandlamudi, Santosh Rathan Paul; Benjamin, Kenneth M.

2018-05-01

Molecular dynamics (MD) simulations were conducted for 1-ethyl-3-methylimidazolium methylsulfate [EMIM][MeSO4] dissolved in six polar covalent molecules [acetic acid, acetone, chloroform, dimethyl sulfoxide (DMSO), isopropyl alcohol, and methanol] to understand the free energies of ionic liquid (IL) ion pairing/aggregation in the limit of infinite dilution. Free energy landscapes or potentials of mean force (PMF) were computed using umbrella sampling and the weighted histogram analysis method. The PMF studies showed the strongest IL ion pairing in chloroform, and the strength of IL ion pairing decreases in the order of chloroform, acetone, propanol, acetic acid, DMSO, and methanol. In the limit of infinite dilution, the free energy curves for IL ion aggregation in co-solvents were characterized by two distinct minima [global (˜3.6 Å) and local (˜5.7 Å)], while free energy values at these minima differed significantly for IL in each co-solvent. The PMF studies were extended for determining the free energy of IL ion aggregation as a function of concentration of methanol. Studies showed that as the concentration of methanol increased, the free energy of ion aggregation decreased, suggesting greater ion pair stability, in agreement with previously reported MD clustering and radial distribution function data.

Influence of different media on micromorphology of radiation synthesized poly(acrylamide-sodium acrylate) hydrogels

International Nuclear Information System (INIS)

Shan Jun; Chen Jie; Liu Zhanjun

1998-01-01

Poly(acrylamide-sodium acrylate) hydrogels were synthesized by 60 Co-γ ray radiation polymerization in aqueous solutions. The micromorphology of hydrogel samples dehydrated in the different alcohol media such as methanol, ethyl alcohol, n-propyl alcohol, iso-propyl alcohol, and tert-butyl alcohol was observed by scanning electron microscope (SEM). The critical concentrations at volume phase transition of the hydrogels in the different alcohol medium-water solutions were obtained. The results indicate that the hydrogel samples dehydrated in methanol and in ethyl alcohol display bubble-film network structures, and those in n-propyl alcohol and in iso-propyl alcohol and in tert-butyl alcohol demonstrate the porous structures including the dense phase. The reason is discussed from the critical concentrations and solubility parameters of different alcohol media. (author)

Free energy of mixing of acetone and methanol: a computer simulation investigation.

Science.gov (United States)

Idrissi, Abdenacer; Polok, Kamil; Barj, Mohammed; Marekha, Bogdan; Kiselev, Mikhail; Jedlovszky, Pál

2013-12-19

The change of the Helmholtz free energy, internal energy, and entropy accompanying the mixing of acetone and methanol is calculated in the entire composition range by the method of thermodynamic integration using three different potential model combinations of the two compounds. In the first system, both molecules are described by the OPLS, and in the second system, both molecules are described by the original TraPPE force field, whereas in the third system a modified version of the TraPPE potential is used for acetone in combination with the original TraPPE model of methanol. The results reveal that, in contrast with the acetone-water system, all of these three model combinations are able to reproduce the full miscibility of acetone and methanol, although the thermodynamic driving force of this mixing is very small. It is also seen, in accordance with the finding of former structural analyses, that the mixing of the two components is driven by the entropy term corresponding to the ideal mixing, which is large enough to overcompensate the effect of the energy increase and entropy loss due to the interaction of the unlike components in the mixtures. Among the three model combinations, the use of the original TraPPE model of methanol and modified TraPPE model of acetone turns out to be clearly the best in this respect, as it is able to reproduce the experimental free energy, internal energy, and entropy of mixing values within 0.15 kJ/mol, 0.2 kJ/mol, and 1 J/(mol K), respectively, in the entire composition range. The success of this model combination originates from the fact that the use of the modified TraPPE model of acetone instead of the original one in these mixtures improves the reproduction of the entropy of mixing, while it retains the ability of the original model of excellently reproducing the internal energy of mixing.

Brief Communication: Comparison of formol-acetone concentration ...

African Journals Online (AJOL)

Background: Formol-ether concentration technique is taken as a gold standard method to detect most intestinal parasites; however, because of its low safety and hazardous impact a need for better technique has a paramount importance. Objective: To evaluate a formol- acetone concentration method in comparison with the ...

Dielectric barrier discharge micro-plasma emission spectrometry for the detection of acetone in exhaled breath.

Science.gov (United States)

Yang, Ting; Gao, Dong-Xue; Yu, Yong-Liang; Chen, Ming-Li; Wang, Jian-Hua

2016-01-01

Acetone is a predominant volatile organic compound (VOC) in the exhaled breath and a promising biomarker for diabetes and ketoacidosis. A non-thermal micro-plasma generated in a planar dielectric barrier discharge (DBD) is used as a radiation source for the excitation of gaseous acetone followed by its quantification with optical emission spectrometry (OES). Gaseous acetone can be directly sampled, while liquid acetone is evaporated by heated tungsten coil and then introduced into the DBD micro-plasma by a helium carrier flow for performing optical emission and detection at a 519 nm emission line. In the present study, the exhaled breath is collected and transferred into aqueous medium for sampling. With a sampling volume of 7 μL in a micro-drop, a linear range of 40-1600 mg L(-1) is obtained along with a detection limit of 44 ng and a precision of 5.7% RSD. The present system is successfully applied to the determination of breath acetone for both diabetic patients and healthy volunteers. Copyright © 2015 Elsevier B.V. All rights reserved.

Involvement of an ATP-dependent carboxylase in a CO2-dependent pathway of acetone metabolism by Xanthobacter strain Py2.

OpenAIRE

Sluis, M K; Small, F J; Allen, J R; Ensign, S A

1996-01-01

The metabolism of acetone by the aerobic bacterium Xanthobacter strain Py2 was investigated. Cell suspensions of Xanthobacter strain Py2 grown with propylene or glucose as carbon sources were unable to metabolize acetone. The addition of acetone to cultures grown with propylene or glucose resulted in a time-dependent increase in acetone-degrading activity. The degradation of acetone by these cultures was prevented by the addition of rifampin and chloramphenicol, demonstrating that new protein...

Acetone production using silicon nanoparticles and catalyst compositions

KAUST Repository

Chaieb, Saharoui; Demellawi, Jehad El; Al-Talla, Zeyad

2015-01-01

Embodiments of the present disclosure provide for a catalytic reaction to produce acetone, a catalyst that include a mixture of silicon particles (e.g., about 1 to 20 nm in diameter) and a solvent, and the like.

Acetone production using silicon nanoparticles and catalyst compositions

KAUST Repository

Chaieb, Sahraoui

2015-12-10

Embodiments of the present disclosure provide for a catalytic reaction to produce acetone, a catalyst that include a mixture of silicon particles (e.g., about 1 to 20 nm in diameter) and a solvent, and the like.

Synthesis of beta zeolite with mesopores from a milk containing precursor and its performance in naphthalene isopropylation

Czech Academy of Sciences Publication Activity Database

Tokarová, V.; Šťávová, G.; Nováková, J.; Stiborová, S.; Kašpárek, A.; Zukal, Arnošt

2017-01-01

Roč. 222, č. 1 (2017), s. 343-356 ISSN 1878-5190 Institutional support: RVO:61388955 Keywords : Beta zeolite * Mesopores * Naphthalene isopropylation Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 1.264, year: 2016

Relationship of O2 Photodesorption in Photooxidation of Acetone on TiO2

International Nuclear Information System (INIS)

Henderson, Michael A.

2008-01-01

Organic photooxidation on TiO2 invariably involves the coexistence of organic species with oxygen on the surface at the same time. In the case of acetone and oxygen, both species exhibit their own interesting photochemistry on TiO2, but interdependences between the two are not understood. In this study, a rutile TiO2(110) surface possessing 7% surface oxygen vacancy sites is used as a model surface to probe the relationship between O2 photodesorption and acetone photodecomposition. Temperature programmed desorption (TPD) and photon stimulated desorption (PSD) measurements indicate that coadsorbed oxygen is essential to acetone photodecomposition on this surface, however the form of oxygen (molecular and dissociative) is not known. The first steps in acetone photodecomposition on TiO2(110) involve thermal activation with oxygen to form an acetone diolate ((CH3)2COO) species followed by photochemical decomposition to adsorbed acetate (CH3COO) and an ejected CH3 radical that is detected in PSD. Depending on the surface conditions, O2 PSD is also observed during the latter process. However, the time scales for the two PSD events (CH3 and O2) are quite different, with the former occurring at ∼10 times faster than the latter. By varying the preheating conditions or performing pre-irradiation on an O2 exposed surface, it becomes clear that the two PSD events are uncorrelated. That is, the O2 species responsible for O2 PSD is not a significant participant in the photochemistry of acetone on TiO2(110) and likely originates from a minority form of O2 on the surface. The CH3 and O2 PSD events do not appear to be in competition with each other suggesting either that ample charge carriers exist under the experimental conditions employed or that different charge carriers or excitation mechanisms are involved

VizieR Online Data Catalog: Iso-propyl cyanide rotational study (Kolesnikova+, 2017)

Science.gov (United States)

Kolesnikova, L.; Alonso, E. R.; Mata, S.; Cernicharo, J.; Alonso, J. L.

2018-02-01

A detailed analysis of the rotational spectra of the interstellar iso-propyl cyanide has been carried out up to 480GHz using three different high-resolution spectroscopic techniques. Jet-cooled broadband chirped pulse Fourier transform microwave spectroscopy from 6 to 18GHz allowed us to measure and analyze the ground-state rotational transitions of all singly substituted 13C and 15N isotopic species in their natural abundances. The monohydrate of iso-propyl cyanide, in which the water molecule bounds through a stronger O-H...N and weaker bifurcated (C-H)2...O hydrogen bonds in a Cs configuration, has also been detected in the supersonic expansion. Stark-modulation spectroscopy in the microwave and millimeter wave range from 18 to 75GHz allowed us to analyze the vibrational satellite pattern arising from pure rotational transitions in the low-lying vibrational excited states. Finally, assignments and measurements were extended through the millimeter and submillimeter wave region. The room temperature rotational spectra made possible the assignment and analysis of pure rotational transitions in 19 vibrationally excited states. Significant perturbations were found above 100GHz in most of the observed excited states. Due to the complexity of the interactions and importance of this astrophysical region for future radioastronomical detection, both a graphical plot approach and a coupled fit have been used to assign and measure almost 10000 new lines. (1 data file).

Acetone-Linked Peptides: A Convergent Approach for Peptide Macrocyclization and Labeling.

Science.gov (United States)

Assem, Naila; Ferreira, David J; Wolan, Dennis W; Dawson, Philip E

2015-07-20

Macrocyclization is a broadly applied approach for overcoming the intrinsically disordered nature of linear peptides. Herein, it is shown that dichloroacetone (DCA) enhances helical secondary structures when introduced between peptide nucleophiles, such as thiols, to yield an acetone-linked bridge (ACE). Aside from stabilizing helical structures, the ketone moiety embedded in the linker can be modified with diverse molecular tags by oxime ligation. Insights into the structure of the tether were obtained through co-crystallization of a constrained S-peptide in complex with RNAse S. The scope of the acetone-linked peptides was further explored through the generation of N-terminus to side chain macrocycles and a new approach for generating fused macrocycles (bicycles). Together, these studies suggest that acetone linking is generally applicable to peptide macrocycles with a specific utility in the synthesis of stabilized helices that incorporate functional tags. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Marangoni convection induced by acetone desorption from the falling soap film

Science.gov (United States)

Sha, Yong; Li, Zhangyun; Wang, Yongyi; Huang, Jiali

2012-05-01

By means of the falling soap film tunnel and the Schlieren optical method, the Marangoni convection were observed directly in the immediate interfacial neighborhood during the desorption process of acetone from the falling soap film. Moreover, the hydraulic characteristics of the falling soap film tunnel, the acetone concentration, the surface tension of the soap liquid and the mass transfer has been investigated in details through the experimental or theoretical method.

Biofiltration of mixtures of gas-phase styrene and acetone with the fungus Sporothrix variecibatus

Energy Technology Data Exchange (ETDEWEB)

Rene, Eldon R.; Spackova, Radka; Veiga, Maria C. [University of La Coruna, Dpt. of Chemical Engineering, Campus da Zapateira, Rua da Fraga, 10, 15008 La Coruna (Spain); Kennes, Christian, E-mail: kennes@udc.es [University of La Coruna, Dpt. of Chemical Engineering, Campus da Zapateira, Rua da Fraga, 10, 15008 La Coruna (Spain)

2010-12-15

The biodegradation performance of a biofilter, inoculated with the fungus Sporothrix variecibatus, to treat gas-phase styrene and acetone mixtures under steady-state and transient conditions was evaluated. Experiments were carried out by varying the gas-flow rates (0.05-0.4 m{sup 3} h{sup -1}), leading to empty bed residence times as low as 17.1 s, and by changing the concentrations of gas-phase styrene (0.01-6.3 g m{sup -3}) and acetone (0.01-8.9 g m{sup -3}). The total elimination capacities were as high as 360 g m{sup -3} h{sup -1}, with nearly 97.5% removal of styrene and 75.6% for acetone. The biodegradation of acetone was inhibited by the presence of styrene, while styrene removal was affected only slightly by the presence of acetone. During transient-state experiments, increasing the overall pollutant load by almost 3-fold, i.e., from 220 to 600 g m{sup -3} h{sup -1}, resulted in a sudden drop of removal efficiency (>90-70%), but still high elimination capacities were maintained. Periodic microscopic observations revealed that the originally inoculated Sporothrix sp. remained present in the reactor and actively dominant in the biofilm.

Crystal structure of 1-isopropyl-4,7-dimethyl-3-nitronaphthalene

Directory of Open Access Journals (Sweden)

Ahmed Benharref

2015-09-01

Full Text Available The title compound, C15H17NO2, was synthesized from a mixture of α-himachalene (2-methylene-6,6,9-trimethylbicyclo[5.4.01,7]undec-8-ene and β-himachalene (2,6,6,9-tetramethylbicyclo[5.4.01,7]undeca-1,8-diene, which were isolated from an oil of the Atlas cedar (Cedrus Atlantica. The naphthalene ring system makes dihedral angles of 68.6 (2 and 44.3 (2°, respectively, with its attached isopropyl C/C/C plane and the nitro group. In the crystal, molecules held together by a C—H...O interaction, forming a chain along [-101].

Decryptification of Acid Phosphatase in Arthrospores of Geotrichum Species Treated with Dimethyl Sulfoxide and Acetone

Science.gov (United States)

Cotter, David A.; Martel, Anita J.; MacDonald, Paul

1975-01-01

Decryptification of acid phosphatase in Geotrichum sp. arthrospores was accomplished using acetone or dimethyl sulfoxide treatment. Both dimethyl sulfoxide and acetone irreversibly destroyed the integrity of the spore membranes without solubilizing acid phosphatase. PMID:1167386

Peroxide formation and kinetics of sodium dissolution in alcohols

International Nuclear Information System (INIS)

Muralidaran, P.; Chandran, K.; Ganesan, V.; Periaswami, G.

1997-01-01

Suitable techniques for sodium removal and decontamination of sodium wetted components of Liquid Metal Fast Reactors (LMFRs) are necessary both for repair, reuse and decommissioning of such components. Among the methods followed for sodium removal, alcohol dissolution is usually employed for small components like bellow sealed valves, gripping tools to handle core components and sodium sampling devices (primary and secondary). One of the concerns in the alcohol dissolution method is the possible role of peroxide formation in the ethoxy group during storage and handling leading to explosion. This paper describes the study of peroxide formation in ethyl carbitol and butyl cellosolve as well as some of the results of dissolution kinetic studies carried out in our laboratory using different alcohols. The peroxide formation of ethyl carbitol and butyl cellosolve were studied by iodometric technique. It has been found that the peroxide formation is less in sodium containing alcohol than in pure one. Ethyl carbitol, butyl cellosolve and Jaysol-SS (mixture of ethyl alcohol, methyl alcohol, isopropyl alcohol and methyl isobutyl ketone) were used in dissolution kinetics studies. The effects due to area and orientation of the fresh sodium surface have also been investigated. The reaction rates were studied in the temperature range of 303-343 K. The rate of dissolution was estimated by measuring the sodium content of alcohol at periodic intervals. It is found that the reaction rate varies in the order of ethyl alcohol-water mixture > Jaysol-SS > butyl cellosolve > ethyl carbitol. While cleaning sodium using alcohol, the concentration of alcohol is held essentially constant throughout the process. The rate of reaction depends only on the amount of sodium and follows pseudo-first order kinetics. Increase in surface area has a marked impact on the dissolution rate at lower temperatures while at higher temperatures, the temperature factor overrides the effect due to surface area

Improvement of the cold flow characteristics of biodiesel containing dissolved polymer wastes using acetone

Directory of Open Access Journals (Sweden)

Pouya Mohammadi

2014-03-01

Full Text Available Due to the fast fossil fuel depletion and at the same time global warming phenomenon anticipated for the next coming years, the necessity of developing alternative fuels e.g. biofuels (i.e. bioethanol, biodiesel, biogas and etc. has turned into an important concern. Recently, the application of the bio-solvency properties of biodiesel for recycling waste polymers has been highlighted. However, the impact of polymer dissolution on cold flow characteristics of biodiesel was never investigated. The present study was set to explore the impact of different solvents in stabilizing biodiesel-polymer solution. Among them, acetone was proved to be the best fuel stabilizer. Subsequently, cold flow characteristic i.e. cloud point, of the biodiesel-polymer-acetone fuel was found to have improved (decreased due to the inclusion of acetone. Finally, flash point analysis of the fuel blends containing acetone was done to ensured high safety of the fuel blend by dramatically increasing the flash point values of biodiesel-polymer fuel blends.

Brain perfusion image using N-isopropyl-p-(/sup 123/I) iodoamphetamine. Detection of interhemispheric difference

Energy Technology Data Exchange (ETDEWEB)

Matsuda, Hiroshi; Seki, Hiroyasu; Ishida, Hiroko

1984-12-01

In brain perfusion images using N-isopropyl-p-(/sup 123/I)iodoamphetamine and rotating gamma camera emission computed tomography, brain maps showing laterality indices (LI) were made for the purpose of detecting intrahemispheric differences. Left (L) and right (R) leteral images were made by adding sagittal section images in each hemisphere, respectively. LI was calculated as follows. LI=100(1 + (R-L)/(R + L)). The normal ranges (mean +- 2 s.d.) of the indices determined by those obtained in five normal right-handed subjects were 103 +- 4 and 103 +- 10 for brain mean and each pixel, respectively. Out of 25 measurements in 22 right-handed patients with cerebrovascular accidents, brain mean LI beyond the normal limits and areas showing abnormal regional LI were observed in 5 (20%) and 21 (84%) measurements, respectively. On the other hand, X-ray CT showed low density areas in only 12 (48%). These brain maps were clinically useful for detecting and quantifying interhemispheric differences in brain perfusion images with N-isopropyl-p-(/sup 123/I)iodoamphetamine. (author). Contains 48 refs.

Lidar/DIAL detection of acetone at 3.3 μm by a tunable OPO laser system

Science.gov (United States)

Puiu, A.; Fiorani, L.; Rosa, O.; Borelli, R.; Pistilli, M.; Palucci, A.

2014-08-01

In this paper we report, for the first time to our knowledge, on lidar/DIAL detection of acetone vapors at 3.3 μm by means of an optical parametric tunable laser system. After a preliminary spectroscopic study in an absorption cell, the feasibility of a differential absorption (DIAL) lidar for the detection of acetone vapors has been investigated in the laboratory, simulating the experimental conditions of a field campaign. Having in mind measurements in a real scenario, a study of possible atmospheric intereferents has been performed, looking for all known compounds that share acetone IR absorption in the spectral band selected for its detection. Possible interfering species from urban and industrial atmospheres were investigated and limits of acetone detection in both environments were identified. This study confirmed that a lidar system can detect a low concentration of acetone at considerable distances.

The Effect of Alcohol on Bead Performance of Encapsulated Iron Using Deacetylated Glucomannan

Directory of Open Access Journals (Sweden)

Wardhani Dyah H.

2018-01-01

Full Text Available The success of encapsulation to protect iron from inhibitor degradation or oxidation depends on many factors including the excipient characteritics. Glucomannan, a neutral heterosaccharide, has a potential for the excipient. To improve the excipient performances, glucomannan is deacetylated to remove the acetyl groups by reacted with Na2CO3. This deacylated glucomannan is subject to bead formation after iron loading. The alcohol solution is commonly used in bead forming as dehydration medium during the encapsulation process. The objective of this work was to study the effect of alcohol on the bead performance of encapsulated iron using deacetylated glucomannan. The bead forming was conducted by dropping the excipient into ethanol and isopropyl alcohol (IPA solution at various concentrations (50, 60, 70, 80 and 90% and two condition temperatures (27-30° and 7-10°C. The encapsulation samples were subject to yield (YE and efficiency of encapsulation (EE. The concentration of alcohol showed a positive impact on the yield and efficiency of encapsulation. Ethanol has a better performance compared with that of IPA regarding yield and efficiency of encapsulation. The optimum of yield bead formation (69.67% and highest EE (66.80% were obtained at 90% ethanol. Temperature of dehydration did not affect the YE and EE significantly.

Substrate dependent reaction channels of the Wolff–Kishner reduction reaction: A theoretical study

Directory of Open Access Journals (Sweden)

Shinichi Yamabe

2014-01-01

Full Text Available Wolff–Kishner reduction reactions were investigated by DFT calculations for the first time. B3LYP/6-311+G(d,p SCRF=(PCM, solvent = 1,2-ethanediol optimizations were carried out. To investigate the role of the base catalyst, the base-free reaction was examined by the use of acetone, hydrazine (H2N–NH2 and (H2O8. A ready reaction channel of acetone → acetone hydrazine (Me2C=N–NH2 was obtained. The channel involves two likely proton-transfer routes. However, it was found that the base-free reaction was unlikely at the N2 extrusion step from the isopropyl diimine intermediate (Me2C(H–N=N–H. Two base-catalyzed reactions were investigated by models of the ketone, H2N–NH2 and OH−(H2O7. Here, ketones are acetone and acetophenone. While routes of the ketone → hydrazone → diimine are similar, those from the diimines are different. From the isopropyl diimine, the N2 extrusion and the C–H bond formation takes place concomitantly. The concomitance leads to the propane product concertedly. From the (1-phenylethyl substituted diimine, a carbanion intermediate is formed. The para carbon of the phenyl ring of the anion is subject to the protonation, which leads to a 3-ethylidene-1,4-cyclohexadiene intermediate. Its [1,5]-hydrogen migration gives the ethylbenzene product. For both ketone substrates, the diimines undergoing E2 reactions were found to be key intermediates.

Application of Raman Spectroscopy for the Detection of Acetone Dissolved in Transformer Oil

Science.gov (United States)

Gu, Z.; Chen, W.; Du, L.; Shi, H.; Wan, F.

2018-05-01

The CLRS detection characteristics of acetone dissolved in transformer oil were analyzed. Raman spectral peak at 780 cm-1 was used as the characteristic spectral peak for qualitative and quantitative analyses. The effect of the detection depth and the temperature was investigated in order to obtain good Raman signals. The optimal detection depth and temperature were set as 3 mm and room temperature. A quantitative model relation between concentration and the Raman peak intensity ratio I 780/I 893 was constructed via the least-squares method. The results demonstrated that CLRS can quantitatively detect the concentration of acetone in transformer oil and CLRS has potential as a useful alternative for accelerating the in-situ analysis of the concentration of acetone in transformer oil.

Application of Raman Spectroscopy for the Detection of Acetone Dissolved in Transformer Oil

Science.gov (United States)

Gu, Z.; Chen, W.; Du, L.; Shi, H.; Wan, F.

2018-05-01

The CLRS detection characteristics of acetone dissolved in transformer oil were analyzed. Raman spectral peak at 780 cm-1 was used as the characteristic spectral peak for qualitative and quantitative analyses. The effect of the detection depth and the temperature was investigated in order to obtain good Raman signals. The optimal detection depth and temperature were set as 3 mm and room temperature. A quantitative model relation between concentration and the Raman peak intensity ratio I 780/ I 893 was constructed via the least-squares method. The results demonstrated that CLRS can quantitatively detect the concentration of acetone in transformer oil and CLRS has potential as a useful alternative for accelerating the in-situ analysis of the concentration of acetone in transformer oil.

Acetone and acetaldehyde determination in tomato juice by isotopic dilution

International Nuclear Information System (INIS)

Piva, M.-T.; Crouzet, J.

1977-01-01

Acetone and acetaldehyde content of tomato juice were determined by isotope dilution techniques. The juice is added to 14 C labelled compounds, carried along by nitrogen at low pressure. The mixture of 2.4 dinitrophenylhydrazones obtained from volatile compounds is separated by thin layer chromatography on silica gel and then on alumina. A determination of radioactivity and concentration of acetone and acetaldehyde 2,4 dinitrophenylhydrazones obtained after separation and elution allow to calculate the content of these two compounds in the initial product with the same sample. This technique could be used for determination of methanol and ethanol after transformation in 3,5 dinitrobenzoates [fr

Optical acetone vapor sensors based on chiral nematic liquid crystals and reactive chiral dopants

NARCIS (Netherlands)

Cachelin, P.; Green, J.P.; Peijs, T.; Heeney, M.; Bastiaansen, C.W.M.

2016-01-01

Accurate monitoring of exposure to organic vapors, such as acetone, is an important part of maintaining a safe working environment and adhering to long- and short-term exposure limits. Here, a novel acetone vapor detection system is described based on the use of a reactive chiral dopant in a nematic

Biodegradation of airborne acetone/styrene mixtures in a bubble column reactor.

Science.gov (United States)

Vanek, T; Silva, A; Halecky, M; Paca, J; Ruzickova, I; Kozliak, E; Jones, K

2017-07-29

The ability of a bubble column reactor (BCR) to biodegrade a mixture of styrene and acetone vapors was evaluated to determine the factors limiting the process efficiency, with a particular emphasis on the presence of degradation intermediates and oxygen levels. The results obtained under varied loadings and ratios were matched with the dissolved oxygen levels and kinetics of oxygen mass transfer, which was assessed by determination of k L a coefficients. A 1.5-L laboratory-scale BCR was operated under a constant air flow of 1.0 L.min -1 , using a defined mixed microbial population as a biocatalyst. Maximum values of elimination capacities/maximum overall specific degradation rates of 75.5 gC.m -3 .h -1 /0.197 gC.gdw -1 .h -1 , 66.0 gC.m -3 .h -1 /0.059 gC.gdw -1 .h -1 , and 45.8 gC.m -3 .h -1 /0.027 gC.gdw -1 .h -1 were observed for styrene/acetone 2:1, styrene-rich and acetone-rich mixtures, respectively, indicating significant substrate interactions and rate limitation by biological factors. The BCR removed both acetone and styrene near-quantitatively up to a relatively high organic load of 50 g.m -3 .h -1 . From this point, the removal efficiencies declined under increasing loading rates, accompanied by a significant drop in the dissolved oxygen concentration, showing a process transition to oxygen-limited conditions. However, the relatively efficient pollutant removal from air continued, due to significant oxygen mass transfer, up to a threshold loading rate when the accumulation of acetone and degradation intermediates in the aqueous medium became significant. These observations demonstrate that oxygen availability is the limiting factor for efficient pollutant degradation and that accumulation of intermediates may serve as an indicator of oxygen limitation. Microbial (activated sludge) analyses revealed the presence of amoebae and active nematodes that were not affected by variations in operational conditions.

Enhancing blood donor skin disinfection using natural oils.

Science.gov (United States)

Alabdullatif, Meshari; Boujezza, Imen; Mekni, Mohamed; Taha, Mariam; Kumaran, Dilini; Yi, Qi-Long; Landoulsi, Ahmed; Ramirez-Arcos, Sandra

2017-12-01

Effective donor skin disinfection is essential in preventing bacterial contamination of blood components with skin flora bacteria like Staphylococcus epidermidis. Cell aggregates of S. epidermidis (biofilms) are found on the skin and are resistant to the commonly used donor skin disinfectants chlorhexidine-gluconate and isopropyl alcohol. It has been demonstrated that essential oils synergistically enhance the antibacterial activity of chlorhexidine-gluconate. The objective of this study was to test plant-extracted essential oils in combination with chlorhexidine-gluconate or chlorhexidine-gluconate plus isopropyl alcohol for their ability to eliminate S. epidermidis biofilms. The composition of oils extracted from Artemisia herba-alba, Lavandula multifida, Origanum marjoram, Rosmarinus officinalis, and Thymus capitatus was analyzed using gas chromatography-mass spectrometry. A rabbit model was used to assess skin irritation caused by the oils. In addition, the anti-biofilm activity of the oils used alone or in combination with chlorhexidine-gluconate or chlorhexidine-gluconate plus isopropyl alcohol was tested against S. epidermidis biofilms. Essential oil concentrations 10%, 20%, and 30% were chosen for anti-biofilm assays, because skin irritation was observed at concentrations greater than 30%. All oils except for O. marjoram had anti-biofilm activity at these three concentrations. L. multifida synergistically enhanced the anti-biofilm activity of chlorhexidine-gluconate and resulted in the highest anti-biofilm activity observed when combined with chlorhexidine-gluconate plus isopropyl alcohol. Gas chromatography-mass spectrometry revealed that the main component contributing to the activity of L. multifida oil was a natural terpene alcohol called linalool. The anti-biofilm activity of chlorhexidine-gluconate plus isopropyl alcohol can be greatly enhanced by L. multifida oil or linalool. Therefore, these components could potentially be used to improve blood

Investigation of efficiency of air cleaning from acetone using a segmental construction biofilter

Directory of Open Access Journals (Sweden)

Denas Bacevičius

2015-10-01

Full Text Available Volatile organic compounds, e. g. acetone, have a direct impact on climate change, decrease of ozone in the air, and on the growth of greenhouse effect. One of the most popular air purifying methods from VOC is a biological air cleaning. Experimental investigations were conducted to determine the efficiency of the new structure of biofilter with polypropylene plates segments. During the investigations the efficiency of segmental construction biofilter of air purification at different initial concentrations of pollutants was determined. Different concentrations of pollutants were estimated during the acetone dilution with water. During the tests the efficiency of biofilter air purification from acetone vapor and its change under different concentrations of vapors was set. Based on test results, the maximum efficiency of biofilter air purification was up to 93%. Studies have shown that increasing the allowable pollutant concentration, the efficiency of air purification unit decreases. Increasing the concentration of supplied acetone vapor into the biofilter from 232 to 701 mg/m3, cleaning efficiency decreased from 92.8 to 82.3%. Since microorganisms fail to oxidize organic compounds, the filter works better at lower initial concentrations of pollutants.

Role of Acetone in the Formation of Highly Dispersed Cationic Polystyrene Nanoparticles

Directory of Open Access Journals (Sweden)

Ernawati Lusi

2017-03-01

Full Text Available A modified emulsion polymerisation synthesis route for preparing highly dispersed cationic polystyrene (PS nanoparticles is reported. The combined use of 2,2′-azobis[2-(2-imidazolin- 2-ylpropane] di-hydrochloride (VA-044 as the initiator and acetone/water as the solvent medium afforded successful synthesis of cationic PS particles as small as 31 nm in diameter. A formation mechanism for the preparation of PS nanoparticles was proposed, whereby the occurrence of rapid acetone diffusion caused spontaneous rupture of emulsion droplets into smaller droplets. Additionally, acetone helped to reduce the surface tension and increase the solubility of styrene, thus inhibiting aggregation and coagulation among the particles. In contrast, VA-044 initiator could effectively regulate the stability of the PS nanoparticles including both the surface charge and size. Other reaction parameters i.e. VA-044 concentration and reaction time were examined to establish the optimum polymerisation conditions.

Crystallinity and properties of C60 nanotubes improved by annealing and alcohol-soaking

Science.gov (United States)

Naito, K.; Matsuishi, K.

2009-04-01

Well-uniformed C60 nanotubes were grown at -20 °C with irradiation of red light using C60-saturated pyridine solution and isopropyl alcohol by a liquid-liquid interfacial precipitation method without ultrasonic pulverization. We attempted to improve their crystallinity by two post-treatments; thermal annealing and alcohol-soaking. The crystallinity of as-grown and dried C60 nanotubes, which was poor due to the evaporation of solvent molecules from crystals in the drying process, was improved by annealing around 220 °C for 5 hours in vacuum. Dramatic improvement of crystallinity of as-grown samples was achieved by soaking into methanol and then drying in air. Raman, infrared and X-ray diffraction results suggest that the methanol-soaked samples exhibit a solvated tetragonal structure. The crystallinity improved by methanol-soaking did not degrade after removal of methanol molecules from samples by thermal annealing. Photo-polymerization of the structurally-improved C60 nanotubes was examined to investigate an effect of crystallinity on the polymerization kinetics.

Crystallinity and properties of C60 nanotubes improved by annealing and alcohol-soaking

International Nuclear Information System (INIS)

Naito, K; Matsuishi, K

2009-01-01

Well-uniformed C 60 nanotubes were grown at -20 deg. C with irradiation of red light using C 60 -saturated pyridine solution and isopropyl alcohol by a liquid-liquid interfacial precipitation method without ultrasonic pulverization. We attempted to improve their crystallinity by two post-treatments; thermal annealing and alcohol-soaking. The crystallinity of as-grown and dried C 60 nanotubes, which was poor due to the evaporation of solvent molecules from crystals in the drying process, was improved by annealing around 220 deg. C for 5 hours in vacuum. Dramatic improvement of crystallinity of as-grown samples was achieved by soaking into methanol and then drying in air. Raman, infrared and X-ray diffraction results suggest that the methanol-soaked samples exhibit a solvated tetragonal structure. The crystallinity improved by methanol-soaking did not degrade after removal of methanol molecules from samples by thermal annealing. Photo-polymerization of the structurally-improved C 60 nanotubes was examined to investigate an effect of crystallinity on the polymerization kinetics.

Measurements of acetone yields from the OH-initiated oxidation of terpenes by proton-transfer-reaction mass spectrometry

International Nuclear Information System (INIS)

Wisthaler, A.; Lindinger, W.; Jensen, N.R.; Winterhalter, R.; Hjorth, J.

2002-01-01

Biogenic VOCs (Volatile Organic Compounds) are known to be emitted in large quantities from vegetation exceeding largely global emissions of anthropogenic VOCs. Monoterpenes (C 10 H 16 ) are important constituents of biogenic VOC emissions. The atmospheric oxidation of Monoterpenes appears to be a potentially relevant source of acetone in the atmosphere. Acetone is present as a significant trace gas in the whole troposphere and influences in particular the atmospheric chemistry in the upper troposphere by substantially contributing to the formation of HO x radicals and peroxyacetyl nitrate (PAN). Acetone is formed promptly, following attack by the OH-radical on the terpene, via a series of highly unstable radical intermediates, but it is also formed slowly via the degradation of stable non-radical intermediates such as pinonaldehyde and nopinone. In order to investigate the relative importance of these processes, the OH-initiated oxidation of α-pinene and β-pinene was investigated in a chamber study, where the concentrations of monoterpenes, acetone, pinonaldehyde and nopinone were monitored by proton-transfer-reaction mass spectrometry (PTR-MS). It was found that significant amounts of acetone are formed directly, whenα-pinene and β-pinene are oxidized by the OH radical, but also secondary chemistry (degradation of primary reaction products) gives a significant contribution to the formation of acetone from monoterpenes. It can be concluded that atmospheric oxidation of monoterpenes contributes a significant fraction to the global acetone source strength. (nevyjel)

UV resistibility of a nano-ZnO/glass fibre reinforced epoxy composite

International Nuclear Information System (INIS)

Wong, Tsz-ting; Lau, Kin-tak; Tam, Wai-yin; Leng, Jinsong; Etches, Julie A.

2014-01-01

Highlights: • A GFRE composite with UV resistibility is introduced. • The bonding behaviour and UV resistibility of the composite were studied upon the addition of nano-ZnO particles. • The solvent effect in the dispersion of nano-ZnO particles was also studied. • The nano-ZnO/GFRE composite shows effective UV absorption with enhanced bonding behaviour. - Abstract: The harmfulness of ultraviolet (UV) radiation (UVR) to human health and polymer degradation has been the focus recently in all engineering industries. A polymer-based composite filled with nano-ZnO particles can enhance its UV resistibility. It has been found that the use of appropriate amount of nano-ZnO/Isopropyl alcohol solvent to prepare a UV resistant nano-ZnO/glass fibre reinforced epoxy (ZGFRE) composite can effectively block the UV transmission with negligible influence on the crystal structure of its resin system. This paper aims at investigating the interfacial bonding behaviour and UV resistibility of a ZGFRE composite. The solvent effect in relation to the dispersion properties of ZnO in the composite is also discussed. XRD results indicated that 20 wt% Isopropyl alcohol was an effective solvent for filling nano-ZnO particles into an epoxy. SEM examination also showed that the bonding behaviour between glass fibre and matrix was enhanced after filling 20 wt% nano-ZnO particles with 20 wt% Isopropyl alcohol into the composite. Samples filled with 20 wt% nano-ZnO/Isopropyl alcohol and 40 wt% nano-ZnO/Isopropyl alcohol has full absorption of UVA (315–400 nm), UVB (280–315 nm) and a part of UVC (190–280 nm)

Radical Scavenging by Acetone: A New Perspective to Understand Laccase/ABTS Inactivation and to Recover Redox Mediator.

Science.gov (United States)

Liu, Hao; Zhou, Pandeng; Wu, Xing; Sun, Jianliang; Chen, Shicheng

2015-11-04

The biosynthetic utilization of laccase/mediator system is problematic because the use of organic cosolvent causes significant inhibition of laccase activity. This work explored how the organic cosolvent impacts on the laccase catalytic capacity towards 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) in aqueous solution. Effects of acetone on the kinetic constants of laccase were determined and the results showed Km and Vmax varied exponentially with increasing acetone content. Acetone as well as some other cosolvents could transform ABTS radicals into its reductive form. The content of acetone in media significantly affected the radical scavenging rates. Up to 95% of the oxidized ABTS was successfully recovered in 80% (v/v) acetone in 60 min. This allows ABTS recycles at least six times with 70%-75% of active radicals recovered after each cycle. This solvent-based recovery strategy may help improve the economic feasibility of laccase/ABTS system in biosynthesis.

Solute-solvent complex switching dynamics of chloroform between acetone and dimethylsulfoxide-two-dimensional IR chemical exchange spectroscopy.

Science.gov (United States)

Kwak, Kyungwon; Rosenfeld, Daniel E; Chung, Jean K; Fayer, Michael D

2008-11-06

Hydrogen bonds formed between C-H and various hydrogen bond acceptors play important roles in the structure of proteins and organic crystals, and the mechanisms of C-H bond cleavage reactions. Chloroform, a C-H hydrogen bond donor, can form weak hydrogen-bonded complexes with acetone and with dimethylsulfoxide (DMSO). When chloroform is dissolved in a mixed solvent consisting of acetone and DMSO, both types of hydrogen-bonded complexes exist. The two complexes, chloroform-acetone and chloroform-DMSO, are in equilibrium, and they rapidly interconvert by chloroform exchanging hydrogen bond acceptors. This fast hydrogen bond acceptor substitution reaction is probed using ultrafast two-dimensional infrared (2D-IR) vibrational echo chemical exchange spectroscopy. Deuterated chloroform is used in the experiments, and the 2D-IR spectrum of the C-D stretching mode is measured. The chemical exchange of the chloroform hydrogen bonding partners is tracked by observing the time-dependent growth of off-diagonal peaks in the 2D-IR spectra. The measured substitution rate is 1/30 ps for an acetone molecule to replace a DMSO molecule in a chloroform-DMSO complex and 1/45 ps for a DMSO molecule to replace an acetone molecule in a chloroform-acetone complex. Free chloroform exists in the mixed solvent, and it acts as a reactive intermediate in the substitution reaction, analogous to a SN1 type reaction. From the measured rates and the equilibrium concentrations of acetone and DMSO, the dissociation rates for the chloroform-DMSO and chloroform-acetone complexes are found to be 1/24 ps and 1/5.5 ps, respectively. The difference between the measured rate for the complete substitution reaction and the rate for complex dissociation corresponds to the diffusion limited rate. The estimated diffusion limited rate agrees well with the result from a Smoluchowski treatment of diffusive reactions.

The use of acetone to enhance the infiltration of HA nanoparticles into a demineralized dentin collagen matrix.

Science.gov (United States)

Besinis, Alexandros; van Noort, Richard; Martin, Nicolas

2016-03-01

This study investigates the role of acetone, as a carrier for nano-hydroxyapatite (nano-HA) in solution, to enhance the infiltration of fully demineralized dentin with HA nanoparticles (NPs). Dentin specimens were fully demineralized and subsequently infiltrated with two types of water-based nano-HA solutions (one containing acetone and one without). Characterization of the dentin surfaces and nano-HA particles was performed using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The surface wettability and infiltration capacity of the nano-HA solutions were quantified by means of contact angle measurements and energy dispersive X-ray spectroscopy (EDS), respectively. Contact angle measurements were taken at baseline and repeated at regular intervals to assess the effect of acetone. The P and Ca levels of infiltrated dentin specimens were measured and compared to sound dentin and non-infiltrated controls. The presence of acetone resulted in an eight-fold decrease in the contact angles of the nano-HA solutions recorded on the surface of demineralized dentin compared to nano-HA solutions without acetone (one-way ANOVA, pacetone. Infiltration of demineralized dentin with the nano-HA solution containing acetone restored the lost mineral content by 50%, whereas the mean mineralization values for P and Ca in dentin treated with the acetone-free nano-HA solution were less than 6%. Acetone was shown to act as a vehicle to enhance the capacity to infiltrate demineralized dentin with HA NPs. The successful infiltration of dentin collagen with HA NPs provides a suitable scaffold, whereby the infiltrated HA NPs have the potential to act as seeds that may initiate heterogenous mineral growth when exposed to an appropriate mineral-rich environment. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Polypyrrole nanoparticles fabricated via Triton X-100 micelles template approach and their acetone gas sensing property

Energy Technology Data Exchange (ETDEWEB)

Li, Fake; Li, Hang [Department of Clinical Laboratory Medcine, Research Institute of Surgery, Daping Hospital, Third Military Medical University, Chongqing 400042 (China); Jiang, Hongmin [26th Research Institute, Chinese Electronics Scientific and Technical Group Company, Chongqing 400060 (China); Zhang, Kejun; Chang, Kai; Jia, Shuangrong; Jiang, Wenbin; Shang, Ya; Lu, Weiping [Department of Clinical Laboratory Medcine, Research Institute of Surgery, Daping Hospital, Third Military Medical University, Chongqing 400042 (China); Deng, Shaoli, E-mail: dengsl072@yahoo.com.cn [Department of Clinical Laboratory Medcine, Research Institute of Surgery, Daping Hospital, Third Military Medical University, Chongqing 400042 (China); Chen, Ming, E-mail: chenming1971@yahoo.com [Department of Clinical Laboratory Medcine, Research Institute of Surgery, Daping Hospital, Third Military Medical University, Chongqing 400042 (China)

2013-09-01

Nano-scaled polypyrrole (PPy) particles have been successfully synthesized with the help of Triton X-100 micelles via soft template approach. The polypyrrole nanoparticles have been spin-coated on surface acoustic wave (SAW) transducers to demonstrate their sensing capability toward acetone gas exposure. Field Emission Scanning Electron Microscopes (FE-SEM) and Fourier transform infrared (FT-IR) spectroscopy have been utilized to characterize these PPy nanoparticles. The PPy nanoparticles have an average diameter of 95 nm. The responses of the sensors are linearly associated with the acetone concentrations in the range from 5.5 ppm to 80 ppm. In response to 5.5 ppm acetone exposure, the response and recovery time are 9 s and 8.3 s, respectively. SAW sensors coated with PPy nanoparticles were potentially useful to detect acetone.

Polypyrrole nanoparticles fabricated via Triton X-100 micelles template approach and their acetone gas sensing property

International Nuclear Information System (INIS)

Li, Fake; Li, Hang; Jiang, Hongmin; Zhang, Kejun; Chang, Kai; Jia, Shuangrong; Jiang, Wenbin; Shang, Ya; Lu, Weiping; Deng, Shaoli; Chen, Ming

2013-01-01

Nano-scaled polypyrrole (PPy) particles have been successfully synthesized with the help of Triton X-100 micelles via soft template approach. The polypyrrole nanoparticles have been spin-coated on surface acoustic wave (SAW) transducers to demonstrate their sensing capability toward acetone gas exposure. Field Emission Scanning Electron Microscopes (FE-SEM) and Fourier transform infrared (FT-IR) spectroscopy have been utilized to characterize these PPy nanoparticles. The PPy nanoparticles have an average diameter of 95 nm. The responses of the sensors are linearly associated with the acetone concentrations in the range from 5.5 ppm to 80 ppm. In response to 5.5 ppm acetone exposure, the response and recovery time are 9 s and 8.3 s, respectively. SAW sensors coated with PPy nanoparticles were potentially useful to detect acetone.

NASOPHARYNGEAL CONCENTRATIONS IN THE HUMAN VOLUNTEER BREATHING ACETONE

Science.gov (United States)

In an effort to examine the absorption of a common chemical into the nasopharyngeal region in humans, a 57 year old male volunteer inhaled uniformly labeled 13C-acetone at 1.4 ppm for 30 min while performing different breathing maneuvers; nose inhale, nose exhale (NINE); mouth ...

An acetone microsensor with a ring oscillator circuit fabricated using the commercial 0.18 μm CMOS process.

Science.gov (United States)

Yang, Ming-Zhi; Dai, Ching-Liang; Shih, Po-Jen

2014-07-17

This study investigates the fabrication and characterization of an acetone microsensor with a ring oscillator circuit using the commercial 0.18 μm complementary metal oxide semiconductor (CMOS) process. The acetone microsensor contains a sensitive material, interdigitated electrodes and a polysilicon heater. The sensitive material is α-Fe2O3 synthesized by the hydrothermal method. The sensor requires a post-process to remove the sacrificial oxide layer between the interdigitated electrodes and to coat the α-Fe2O3 on the electrodes. When the sensitive material adsorbs acetone vapor, the sensor produces a change in capacitance. The ring oscillator circuit converts the capacitance of the sensor into the oscillation frequency output. The experimental results show that the output frequency of the acetone sensor changes from 128 to 100 MHz as the acetone concentration increases 1 to 70 ppm.

A Comprehensive Rotational Study of Interstellar Iso-propyl Cyanide up to 480 GHz

Science.gov (United States)

Kolesniková, L.; Alonso, E. R.; Mata, S.; Cernicharo, J.; Alonso, J. L.

2017-12-01

A detailed analysis of the rotational spectra of the interstellar iso-propyl cyanide has been carried out up to 480 GHz using three different high-resolution spectroscopic techniques. Jet-cooled broadband chirped pulse Fourier transform microwave spectroscopy from 6 to 18 GHz allowed us to measure and analyze the ground-state rotational transitions of all singly substituted 13C and 15N isotopic species in their natural abundances. The monohydrate of iso-propyl cyanide, in which the water molecule bounds through a stronger O-H⋯N and weaker bifurcated (C-H)2⋯O hydrogen bonds in a C s configuration, has also been detected in the supersonic expansion. Stark-modulation spectroscopy in the microwave and millimeter wave range from 18 to 75 GHz allowed us to analyze the vibrational satellite pattern arising from pure rotational transitions in the low-lying vibrational excited states. Finally, assignments and measurements were extended through the millimeter and submillimeter wave region. The room temperature rotational spectra made possible the assignment and analysis of pure rotational transitions in 19 vibrationally excited states. Significant perturbations were found above 100 GHz in most of the observed excited states. Due to the complexity of the interactions and importance of this astrophysical region for future radioastronomical detection, both a graphical plot approach and a coupled fit have been used to assign and measure almost 10,000 new lines.

Gallium-67 citrate used as a tracer of acetone production routes

International Nuclear Information System (INIS)

Mesquita, Carlos Henrique de; Calvo, Wilson A.P.; Aoki, Pedro E.; Silva, Valdir Cosmos da; Haraguchi, Marcio I.; Velo, Alexandre F.; Alvarez, Alexandre G.; Paixão, Leticia B.; Hamada, Margarida M.

2017-01-01

In this work the pathway of the chemical product and the kinetics parameters were evaluated in a laboratory plant settled, using 40 GBq of 67 Ga citrate as radiotracer and 18 NaI(Tl) radiation detectors. The AnaComp program was used to estimate the kinetic parameters of the acetone production. The yield of the acetone production was estimated by the percentage ratio between the areas under the curve (AUC) of the curve profiles of the final product compartment divided by the concentration found inside the chemical reactor whose result was 87% yield during the first 30 minutes of reaction. (author)

Gallium-67 citrate used as a tracer of acetone production routes

Energy Technology Data Exchange (ETDEWEB)

Mesquita, Carlos Henrique de; Calvo, Wilson A.P.; Aoki, Pedro E.; Silva, Valdir Cosmos da; Haraguchi, Marcio I.; Velo, Alexandre F.; Alvarez, Alexandre G.; Paixão, Leticia B.; Hamada, Margarida M., E-mail: chmesqui@usp.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

In this work the pathway of the chemical product and the kinetics parameters were evaluated in a laboratory plant settled, using 40 GBq of {sup 67}Ga citrate as radiotracer and 18 NaI(Tl) radiation detectors. The AnaComp program was used to estimate the kinetic parameters of the acetone production. The yield of the acetone production was estimated by the percentage ratio between the areas under the curve (AUC) of the curve profiles of the final product compartment divided by the concentration found inside the chemical reactor whose result was 87% yield during the first 30 minutes of reaction. (author)

Acetone gas-sensing properties of multiple-networked Pd-decorated Bi_2O_3 nanorod sensors

International Nuclear Information System (INIS)

Park, Sung Hoon; Kim, Soo Hyun; Lee, Sang Min; Lee, Chong Mu

2015-01-01

This study examined the sensing properties of Bi_2O_3 nanorods decorated with Pd nanoparticles. Pd-decorated β-Bi_2O_3 nanorods were prepared by immersing the Bi_2O_3 nanorods in ethanol/(50 mM)PdCl_2 solution followed by UV irradiation and annealing. The Bi_2O_3 nanorods decorated with Pd nanoparticles showed faster and stronger response to acetone gas than the pristine Bi_2O_3 nanorods. Interestingly, the difference in response time between the Pd-decorated Bi_2O_3 nanorod sensor and pristine Bi_2O_3 nanorod sensor increased with increasing the acetone gas concentration. In contrast, the difference in recovery time between the two nanorod sensors decreased with increasing the acetone gas concentration. This difference can be explained using the chemical mechanism. The underlying mechanism for the enhanced response of the Bi_2O_3 nanorods decorated with Pd nanoparticles to acetone gas is also discussed

Use of 90% ethanol to decontaminate stethoscopes in resource limited settings

OpenAIRE

Raghubanshi, Bijendra Raj; Sapkota, Supriya; Adhikari, Arjab; Dutta, Aman; Bhattarai, Utsuk; Bhandari, Rastriyata

2017-01-01

Abstract Background In developing countries like Nepal, 90% ethanol is cheap and is available in most hospitals. The unavailability of isopropyl alcohol (IPA) in these settings led us to compare the efficacy between 90% ethanol and isopropyl alcohol pads in reducing the bacterial contamination of diaphragm of stethoscope. Methods A randomized blinded experimental study was carried out to determine the difference between cleaning stethoscopes with 90% ethanol and IPA. Cultures of diaphragm wer...

Process Development for Reactive-Ion Etching of Molybdenum Disulfide (MoS2) Utilizing a Poly(methyl methacrylate) (PMMA) Etch Mask

Science.gov (United States)

2017-10-01

Nichols, Matthew L Chin, Sina Najmaei, Eugene Zakar, and Madan Dubey Sensors and Electron Devices Directorate, ARL Approved for public...EBL; Vistec EBPG5000+) with an exposure dose of 850 μC/cm2 and development in 25 mL of isopropyl alcohol (IPA): 10 mL methyl isobutyl ketone for...deposition EBL electron beam lithography IPA isopropyl alcohol MoS2 molybdenum disulfide O2 oxygen PMMA poly(methyl methacrylate) RIE reactive

Analysis of human exhaled breath in a population of young volunteers

Directory of Open Access Journals (Sweden)

Zarić Božidarka

2014-01-01

Full Text Available Analysis of volatile organic compounds (VOCs in human breath can provide information about the current physiological state of an individual, such as clinical conditions and exposure to exogenous pollutants. The blood-borne VOCs present in exhaled breath offer the possibility of exploring physiological and pathological processes in a noninvasive way. However, the field of exhaled breath analysis is still in its infancy. We undertook this study in order to define interindividual variation and common compounds in breath VOCs of 48 young human volunteers. Alveolar breath samples were analyzed by automated thermal desorption, gas chromatography with flame ionization detector (FID and electron capture detector (ECD using SUPELCO standards with 66 compounds. Predominant compounds in the alveolar breath of analyzed subjects are ethylbenzene, 1-ethyl-4-methylbenzene, 1,2,4-trimethylbenzene and 1,3,5-trimethylbenzene (over 50% of the subjects. Isopropyl alcohol, propylene, acetone, ethanol were found as well. We detected substituted compounds in exhaled breath. [Projekat Ministarstva nauke Republike Srbije, br. 172001

Role of Alcohol on the Fracture Resistance of Dentin

Energy Technology Data Exchange (ETDEWEB)

Nalla, Ravi K.; Kinney, John H.; Tomsia, Antoni P.; Ritchie,Robert O.

2006-05-01

Healthy dentin, the mineralized tissue that makes up the bulk of the tooth, is naturally hydrated in vivo; however, it is known that various chemical reagents including acetone and ethanol can induce dehydration and thereby affect its properties. Here, we seek to investigate this in light of the effect alcohol can have on the mechanical properties of dentin, specifically by measuring the stiffness, strength and toughness of dentin in simulated body fluid and scotch whisky. Results indicate that chemical dehydration induced by the whisky has a significant beneficial effect on the elastic modulus, strength and fracture toughness of dentin. Although this makes teeth more resistant to fracture, the change in properties is fully reversible upon rehydration. This effect is considered to be associated with increased cross-linking of the collagen molecules from intermolecular hydrogen-bonding where water is replaced with weaker hydrogen-bond forming solvents such as alcohol.

Lidar/DIAL detection of acetone at 3.3 μm by a tunable OPO laser system

International Nuclear Information System (INIS)

Puiu, A; Fiorani, L; Borelli, R; Pistilli, M; Palucci, A; Rosa, O

2014-01-01

In this paper we report, for the first time to our knowledge, on lidar/DIAL detection of acetone vapors at 3.3 μm by means of an optical parametric tunable laser system. After a preliminary spectroscopic study in an absorption cell, the feasibility of a differential absorption (DIAL) lidar for the detection of acetone vapors has been investigated in the laboratory, simulating the experimental conditions of a field campaign. Having in mind measurements in a real scenario, a study of possible atmospheric intereferents has been performed, looking for all known compounds that share acetone IR absorption in the spectral band selected for its detection. Possible interfering species from urban and industrial atmospheres were investigated and limits of acetone detection in both environments were identified. This study confirmed that a lidar system can detect a low concentration of acetone at considerable distances. (paper)

BaFe{sub 12}O{sub 19} powder with high magnetization prepared by acetone-aided coprecipitation

Energy Technology Data Exchange (ETDEWEB)

Yu, Hsuan-Fu, E-mail: hfyu@mail.tku.edu.tw

2013-09-15

BaFe{sub 12}O{sub 19} particles with high magnetization were produced using an acetone-aided coprecipitation process. An aqueous solution of iron and barium nitrates, in an Fe{sup 3+}/Ba{sup 2+} molar ratio of 12, was added in a stirred precipitation liquid medium composed of H{sub 2}O, CH{sub 3}(CO)CH{sub 3} and NH{sub 4}OH. After reacting metallic ions with ammonia, the precipitates were formed, centrifugally filtered, freeze dried and calcined. Effects of amount of the acetone in the precipitation liquid medium on the formation of crystalline BaFe{sub 12}O{sub 19} were investigated. The presence of acetone in the precipitation liquid medium can greatly promote formation of the crystalline BaFe{sub 12}O{sub 19} at temperature as low as 650 °C and can enhance magnetization of the derived particles. On the other hand, raising the calcination temperature can effectively accelerate development of crystallite morphology and magnetic characters of the barium hexaferrites. While the barium hexaferrite powder obtained without acetone additions and calcined at 1000 °C had magnetization (measured at 50 kOe; M(50 kOe)) of 63.5 emu/g, remanence magnetization (Mr) of 31.3 emu/g and coercivity (Hc) of 4.7 kOe, the single magnetic domain size BaFe{sub 12}O{sub 19} powder with M(50 kOe) of 70.6 emu/g, Mr of 34.4 emu/g and Hc of 3.7 kOe was produced at 1000 °C, using a precipitation liquid medium of 64 vol% acetone. - Highlights: • BaFe{sub 12}O{sub 19} with high magnetic characters was produced by an acetone-aided coprecipitation. • The effects of acetone addition in the precipitation on the formation of BaFe{sub 12}O{sub 19} were studied. • Acetone presence in the precipitation liquid medium promoted BaFe{sub 12}O{sub 19} formation at ≥650 °C. • BaFe{sub 12}O{sub 19} with M(50 kOe) of 70.6 emu/g, Mr of 34.4 emu/g and Hc of 3.7 kOe was obtained.

Acetone photophysics at 282 nm excitation at elevated pressure and temperature. II: Fluorescence modeling

Science.gov (United States)

Hartwig, Jason; Raju, Mandhapati; Sung, Chih-Jen

2017-07-01

This is the second in a series of two papers that presents an updated fluorescence model and compares with the new experimental data reported in the first paper, as well as the available literature data, to extend the range of acetone photophysics to elevated pressure and temperature conditions. This work elucidates the complete acetone photophysical model in terms of each and every competing radiative and non-radiative rate. The acetone fluorescence model is then thoroughly examined and optimized based on disparity with recently conducted elevated pressure and temperature photophysical calibration experiments. The current work offers insight into the competition between non-radiative and vibrational energy decay rates at elevated temperature and pressure and proposes a global optimization of model parameters from the photophysical model developed by Thurber (Acetone Laser-Induced Fluorescence for Temperature and Multiparameter Imaging in Gaseous Flows. PhD thesis, Stanford University Mechanical Engineering Department, 1999). The collisional constants of proportionality, which govern vibrational relaxation, are shown to be temperature dependent at elevated pressures. A new oxygen quenching rate is proposed which takes into account collisions with oxygen as well as the oxygen-assisted intersystem crossing component. Additionally, global trends in ketone photophysics are presented and discussed.

Rapid and selective detection of acetone using hierarchical ZnO gas sensor for hazardous odor markers application

International Nuclear Information System (INIS)

Jia, Qianqian; Ji, Huiming; Zhang, Ying; Chen, Yalu; Sun, Xiaohong; Jin, Zhengguo

2014-01-01

Highlights: • ZnO spheres fabricated via solvothermal method are with (0 0 2) polar facet exposed. • Response time of ZnO sensor for detecting 100 ppm acetone is as short as 3 s. • R a /R g toward 100 ppm acetone is 33 when operated at 230 °C. • ZnO sensor exhibits good selectivity against other toxic gases and water vapor. • Porous structure and exposure of polar facet contribute to good sensing properties. - Abstract: Hierarchical nanostructured ZnO dandelion-like spheres were synthesized via solvothermal reaction at 200 °C for 4 h. The products were pure hexagonal ZnO with large exposure of (0 0 2) polar facet. Side-heating gas sensor based on hierarchical ZnO spheres was prepared to evaluate the acetone gas sensing properties. The detection limit to acetone for the ZnO sensor is 0.25 ppm. The response (R a /R g ) toward 100 ppm acetone was 33 operated at 230 °C and the response time was as short as 3 s. The sensor exhibited remarkable acetone selectivity with negligible response toward other hazardous gases and water vapor. The high proportion of electron depletion region and oxygen vacancies contributed to high gas response sensitivity. The hollow and porous structure of dandelion-like ZnO spheres facilitated the diffusion of gas molecules, leading to a rapid response speed. The largely exposed (0 0 2) polar facets could adsorb acetone gas molecules easily and efficiently, resulting in a rapid response speed and good selectivity of hierarchical ZnO spheres gas sensor at low operating temperature

First discovery of acetone extract from cottonseed oil sludge as a novel antiviral agent against plant viruses.

Science.gov (United States)

Zhao, Lei; Feng, Chaohong; Hou, Caiting; Hu, Lingyun; Wang, Qiaochun; Wu, Yunfeng

2015-01-01

A novel acetone extract from cottonseed oil sludge was firstly discovered against plant viruses including Tobacco mosaic virus (TMV), Rice stripe virus (RSV) and Southern rice black streaked dwarf virus (SRBSDV). Gossypol and β-sitosterol separated from the acetone extract were tested for their effects on anti-TMV and analysed by nuclear magnetic resonance (NMR) assay. In vivo and field trials in different geographic distributions and different host varieties declared that this extract mixture was more efficient than the commercial agent Ningnanmycin with a broad spectrum of anti-plant-viruses activity. No phytotoxic activity was observed in the treated plants and environmental toxicology showed that this new acetone extract was environmentally friendly, indicating that this acetone extract has potential application in the control of plant virus in the future.

[Modification of the pattern of fatty acids of erythrocytes’ membranes due to the acetone intoxication].

Science.gov (United States)

Momot, T V; Kushnerova, N F; Rakhmanin, Yu A

Results of the study of the impact of acetone intoxication on the fatty acids pattern of the general lipids of erythrocytes’ membranes in rats are presented. The inhalation exposure of acetone was carried out in the inoculation chamber with the volume of 100 liters. The chamber was designed for the type of B.A. Kurlyandsky with self-contained system of purification and air regeneration and specified parameters of temperature (20-22С) and air humidity. The flow rate of the air and aerosolized acetone passed through the chamber accounted of 10 liters/min. Concentration of acetone in the chamber was sustained at the level of 206 ± 3,9 mg/m that corresponds to maximum permissible concentration for acetone vapor in the air of a working area. The time of exposure was 6 hours per day for 3 weeks in a monotonous mode, excluding weekend, and was based upon specific parameters of environment simulation in industry. The acetone impact was shown to be accompanied by the gain in the quantity of all kinds of saturated fatty acids and the fall of unsaturated fatty acids in general lipids of erythrocytes ’ membranes in rats and in the structure ofphospholipid fractions. In the content of phosphatydilcholine and phosphatydilethanolamine, as a basic structural phospholipids of biological membranes, there was noted the increase in palmitic and stearic acids. In the range offatty acids of the n-6 family the amount of linoleic and arachidonic acids decreased. In the array of fatty acids of the n-3 family the content of linolenic, eicosapentaenoic and docosahexaenoic acids (n-3 family) declined. Redistribution of fatty acids in the erythrocytes membrane towards to such alteration in quantity as the increasing of saturation and decreasing of the unsaturated fatty acids supposes the change of its physical and chemical properties, permeability, lability and complexity of passing erythrocyte via microcircular channels.

Aromatherapy Versus Oral Ondansetron for Antiemetic Therapy Among Adult Emergency Department Patients: A Randomized Controlled Trial.

Science.gov (United States)

April, Michael D; Oliver, Joshua J; Davis, William T; Ong, David; Simon, Erica M; Ng, Patrick C; Hunter, Curtis J

2018-02-17

We compare aromatherapy with inhaled isopropyl alcohol versus oral ondansetron for treating nausea among emergency department (ED) patients not requiring immediate intravenous access. In a randomized, blinded, placebo-controlled trial, we enrolled a convenience sample of adults presenting to an urban tertiary care ED with chief complaints including nausea or vomiting. We randomized subjects to 1 of 3 arms: inhaled isopropyl alcohol and 4 mg oral ondansetron, inhaled isopropyl alcohol and oral placebo, and inhaled saline solution placebo and 4 mg oral ondansetron. The primary outcome was mean nausea reduction measured by a 0- to 100-mm visual analog scale from enrollment to 30 minutes postintervention. Secondary outcomes included receipt of rescue antiemetic medications and adverse events. We enrolled 122 subjects, of whom 120 (98.3%) completed the study. Of randomized subjects, 40 received inhaled isopropyl alcohol and oral ondansetron, 41 received inhaled isopropyl alcohol and oral placebo, and 41 received inhaled saline solution placebo and oral ondansetron. The mean decrease in nausea visual analog scale score in each arm was 30 mm (95% confidence interval [CI] 22 to 37 mm), 32 mm (95% CI 25 to 39 mm), and 9 mm (95% CI 5 to 14 mm), respectively. The proportions of subjects who received rescue antiemetic therapy in each arm were 27.5% (95% CI 14.6% to 43.9%), 25.0% (95% CI 12.7% to 41.2%), and 45.0% (95% CI 29.3% to 61.5%), respectively. There were no adverse events. Among ED patients with acute nausea and not requiring immediate intravenous access, aromatherapy with or without oral ondansetron provides greater nausea relief than oral ondansetron alone. Copyright © 2018 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

Comparative effectiveness of skin antiseptic agents in reducing surgical site infections: a report from the Washington State Surgical Care and Outcomes Assessment Program.

Science.gov (United States)

Hakkarainen, Timo W; Dellinger, E Patchen; Evans, Heather L; Farjah, Farhood; Farrokhi, Ellen; Steele, Scott R; Thirlby, Richard; Flum, David R

2014-03-01

Surgical site infections (SSI) are an important source of morbidity and mortality. Chlorhexidine in isopropyl alcohol is effective in preventing central venous-catheter associated infections, but its effectiveness in reducing SSI in clean-contaminated procedures is uncertain. Surgical studies to date have had contradictory results. We aimed to further evaluate the relationship of commonly used antiseptic agents and SSI, and to determine if isopropyl alcohol has a unique effect. We performed a prospective cohort analysis to evaluate the relationship of commonly used skin antiseptic agents and SSI for patients undergoing mostly clean-contaminated surgery from January 2011 through June 2012. Multivariate regression modeling predicted expected rates of SSI. Risk adjusted event rates (RAERs) of SSI were compared across groups using proportionality testing. Among 7,669 patients, the rate of SSI was 4.6%. The RAERs were 0.85 (p = 0.28) for chlorhexidine (CHG), 1.10 (p = 0.06) for chlorhexidine in isopropyl alcohol (CHG+IPA), 0.98 (p = 0.96) for povidone-iodine (PVI), and 0.93 (p = 0.51) for iodine-povacrylex in isopropyl alcohol (IPC+IPA). The RAERs were 0.91 (p = 0.39) for the non-IPA group and 1.10 (p = 0.07) for the IPA group. Among elective colorectal patients, the RAERs were 0.90 (p = 0.48) for CHG, 1.04 (p = 0.67) for CHG+IPA, 1.04 (p = 0.85) for PVI, and 1.00 (p = 0.99) for IPC+IPA. For clean-contaminated surgical cases, this large-scale state cohort study did not demonstrate superiority of any commonly used skin antiseptic agent in reducing the risk of SSI, nor did it find any unique effect of isopropyl alcohol. These results do not support the use of more expensive skin preparation agents. Copyright © 2014 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

Some problems of local production of acetone and butanol

Energy Technology Data Exchange (ETDEWEB)

Fang, C; Chang, Y P

1959-01-01

Conditions of laboratory and plant cultivation of acetone-butanol fermentation bacteria are considered (effects of pH of the medium, temperature, and starch content in raw material on yield of fermentation products) and also the conditions of isolation of the final products produced.

In vitro antimycobacterial activity of acetone extract of Glycyrrhiza glabra

Directory of Open Access Journals (Sweden)

Swapna S. Nair

2015-08-01

Full Text Available Context: Glycyrrhiza glabra (licorice has been used since ages as expectorant, antitussive and demulcent. G. glabra has been indicated in Ayurveda as an antimicrobial agent for the treatment of respiratory infections and tuberculosis. Aims: To evaluate the antimycobacterial activity of acetone extract of G. glabra by in vitro techniques. Methods: The anti-tubercular activity of acetone extract of G. glabra, obtained by Soxhlet extraction, was evaluated against Mycobacterium tuberculosis H37Rv (ATCC 27294. The in vitro anti-tubercular activity was determined by Resazurin Microtiter Plate Assay (REMA and colony count method. Further, the anti-tubercular activity of acetone extract of G. glabra was determined in human macrophage U937 cell lines and was compared against that of the standard drugs isoniazid, rifampicin and ethambutol. Results: G. glabra extract showed significant activity against Mycobacterium tuberculosis, when evaluated by REMA/colony count methods and in U937 human macrophage cell lines infected with Mycobacterium tuberculosis H37Rv. The activity of the extract was comparable to those of standard drugs. It was observed that the extract showed time and concentration dependent antimycobacterial activity. Conclusions: The present study reveals that G. glabra extract has promising anti-tubercular activity by preliminary in vitro techniques and in U937 macrophage cell line. Therefore, it has the definite potential to be developed as an affordable, cost-effective drug against tuberculosis.

Hydrate phase equilibria of furan, acetone, 1,4-dioxane, TBAC and TBAF

International Nuclear Information System (INIS)

Kamran-Pirzaman, Arash; Pahlavanzadeh, Hassan; Mohammadi, Amir H.

2013-01-01

Highlights: • Experimental hydrate dissociation conditions are reported for CO 2 /methane + some water soluble/insoluble hydrate formers. • An isochoric pressure-search method was used to generate the experimental data. • The data are compared with the corresponding literature data in the presence of pure water. • The hydrate promotion effects of acetone, 1,4-dioxane, furan, TBAC and TBAF are discussed. -- Abstract: In this communication, we first report experimental hydrate dissociation pressures for the methane/carbon dioxide + furan/acetone/1,4-dioxane + water and the methane + tetra n-butyl ammonium chloride (TBAC) + water as well as the carbon dioxide + tetra n-butyl ammonium floride (TBAF) + water systems in the temperature ranges of (269.9 to 303.3) K. An isochoric pressure-search method was used to generate the experimental data. The hydrate dissociation data are compared with the corresponding literature data, if exists, and the literature data in the presence of pure water and acceptable agreement is observed. A discussion is made on hydrate promotion effects of acetone, 1,4-dioxane, furan, TBAC and TBAF

21 CFR 172.560 - Modified hop extract.

Science.gov (United States)

2010-04-01

..., ethyl alcohol, or isopropyl alcohol acidified with hydrochloric or sulfuric acid; oxidation with peracetic acid; isomerization by calcium chloride or magnesium chloride treatment in ethylene dichloride...

A facile synthesis of sodium 3-[1-[sup 14]C]-ethyl-7-isopropyl-1-azulenesulfonate

Energy Technology Data Exchange (ETDEWEB)

Shimada, Takeshi; Yanagisawa, Takashi; Tomiyama, Tsuyoshi [Kotobuki Pharmaceutical Co. Ltd., Nagano (Japan). Research Labs.; Okazaki, Mitsuo [Shinshu Univ., Nagano (Japan). Dept. of Applied Biology

1994-01-01

Sodium 3-ethyl-7-isopropyl-1-azulenesulfonate 1, a new therapeutic agent for stomatitis, pharyngitis and ophthalmia was labelled with carbon-14 in the ethyl group attached to the azulene ring for use in metabolic studies. [sup 14]C-labelled 1 with a specific activity of 1.98 GBq/mmol was prepared in four steps in 39.3% overall chemical yield from [1-[sup 14]C]acetic acid sodium salt. (Author).

A photoelectron and TPEPICO investigation of the acetone radical cation.

Science.gov (United States)

Rennie, Emma E; Boulanger, Anne-Marie; Mayer, Paul M; Holland, David M P; Shaw, David A; Cooper, Louise; Shpinkova, Larisa G

2006-07-20

The valence shell photoelectron spectrum, threshold photoelectron spectrum, and threshold photoelectron photoion coincidence (TPEPICO) mass spectra of acetone have been measured using synchrotron radiation. New vibrational progressions have been observed and assigned in the X 2B2 state photoelectron bands of acetone-h6 and acetone-d6, and the influence of resonant autoionization on the threshold electron yield has been investigated. The dissociation thresholds for fragment ions up to 31 eV have been measured and compared to previous values. In addition, kinetic modeling of the threshold region for CH3* and CH4 loss leads to new values of 78 +/- 2 kJ mol(-1) and 75 +/- 2 kJ mol(-1), respectively, for the 0 K activation energies for these two processes. The result for the methyl loss channel is in reasonable agreement with, but slightly lower than, that of 83 +/- 1 kJ mol(-1) derived in a recent TPEPICO study by Fogleman et al. The modeling accounts for both low-energy dissociation channels at two different ion residence times in the mass spectrometer. Moreover, the effects of the ro-vibrational population distribution, the electron transmission efficiency, and the monochromator band-pass are included. The present activation energies yield a Delta(f)H298 for CH3CO+ of 655 +/- 3 kJ mol(-1), which is 4 kJ mol(-1) lower than that reported by Fogleman et al. The present Delta(f)H298 for CH3CO+ can be combined with the Delta(f)H298 for CH2CO (-47.5 +/- 1.6 kJ mol(-1)) and H+ (1530 kJ mol(-1)) to yield a 298 K proton affinity for ketene of 828 +/- 4 kJ mol(-1), in good agreement with the value (825 kJ mol(-1)) calculated at the G2 level of theory. The measured activation energy for CH4 loss leads to a Delta(f)H298 (CH2CO+*) of 873 +/- 3 kJ mol(-1).

Studies on acetone sensing characteristics of ZnO thin film prepared by sol–gel dip coating

Energy Technology Data Exchange (ETDEWEB)

Muthukrishnan, Karthika; Vanaraja, Manoj [School of Electrical & Electronics Engineering, SASTRA University, Thanjavur, 613401 (India); Boomadevi, Shanmugam [Department of Physics, National Institute of Technology, Tiruchirappalli, 620015 (India); Karn, Rakesh Kumar [School of Electrical & Electronics Engineering, SASTRA University, Thanjavur, 613401 (India); Singh, Vijay [Department of Chemical Engineering, Konkuk University, Seoul, 143-701 (Korea, Republic of); Singh, Pramod K. [Solar Energy Institute, Ege University, Bornova, 35100, Izmir (Turkey); Material Research Laboratory, School of Basic Sciences and Research, Sharda University, Greater Noida, 201310, U. P. (India); Pandiyan, Krishnamoorthy, E-mail: krishpandiyan@ece.sastra.edu [School of Electrical & Electronics Engineering, SASTRA University, Thanjavur, 613401 (India)

2016-07-15

Acetone sensing characteristics of Zinc Oxide thin films prepared by dip coating method are discussed in this paper. The sol for dip coating was synthesized using Zinc nitrate hexahydrate (Zn (NO{sub 3}){sub 2}. 6H{sub 2}O) and organic polymer sodium carboxy methyl cellulose (Na-CMC) as a starting material. Crystallinity and crystallite size of the prepared thin film was characterised by X-ray diffraction (XRD). Morphology was studied using field emission scanning electron microscopy (FESEM). The gas sensing characteristics was studied using chemiresistive method, by exposing the film to various concentrations of acetone at room temperature. Further, for comparative study ethanol and acetaldehyde has also been tested. Gas sensing parameters such us response, selectivity, lowest detection limit, response/recovery time of the thin film towards acetone were also reported. - Highlights: • ZnO has successfully synthesized using cheap and ease method. • Detail characterization have carried out and explained. • Sensing behaviour has been studied. • Acetone sensor has been fabricated.

A simple procedure for preparing chitin oligomers through acetone precipitation after hydrolysis in concentrated hydrochloric acid.

Science.gov (United States)

Kazami, Nao; Sakaguchi, Masayoshi; Mizutani, Daisuke; Masuda, Tatsuhiko; Wakita, Satoshi; Oyama, Fumitaka; Kawakita, Masao; Sugahara, Yasusato

2015-11-05

Chitin oligomers are of interest because of their numerous biologically relevant properties. To prepare chitin oligomers containing 4-6 GlcNAc units [(GlcNAc)4-6], α- and β-chitin were hydrolyzed with concentrated hydrochloric acid at 40 °C. The reactant was mixed with acetone to recover the acetone-insoluble material, and (GlcNAc)4-6 was efficiently recovered after subsequent water extraction. Composition analysis using gel permeation chromatography and MALDI-TOF mass spectrometry indicated that (GlcNAc)4-6 could be isolated from the acetone-insoluble material with recoveries of approximately 17% and 21% from the starting α-chitin and β-chitin, respectively. The acetone precipitation method is highly useful for recovering chitin oligomers from the acid hydrolysate of chitin. The changes in the molecular size and higher-order structure of chitin during the course of hydrolysis were also analyzed, and a model that explains the process of oligomer accumulation is proposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Inert Reassessment Document for Acetone - CAS No. 67-64-1

Science.gov (United States)

Acetone is a highly volatile chemical that is used as an inert ingredient, a solvent/co-solvent, in a variety of pesticide products (including outdoor yard, garden and turf products, and agricultural crop products).

(1S*,3R*,5S*,7S*-4,4,8,8-Tetrachloro-1-isopropyl-5-methyltricyclo[5.1.0.03,5]octane

Directory of Open Access Journals (Sweden)

Koblandy M. Turdybekov

2014-04-01

Full Text Available The title compound, C12H16Cl4, is a derivative of the natural product 1-isopropyl-4-methylcyclohexa-1,4-diene, and represents a diastereomer with two trans-fused cyclopropane rings. Both enantiomers are present in the non-centrosymmetric polar space group Pna21. The central cyclohexane ring is planar within 0.02 (1 Å. The C atoms of dichloromethylene groups deviate from this plane by 1.19 (1 and −1.26 (1 Å, whereas the isopropyl and methyl groups are oriented more equatorially, deviating by 0.71 (1 and −0.87 (1 Å, respectively.

Acetone and Butanone Metabolism of the Denitrifying Bacterium “Aromatoleum aromaticum” Demonstrates Novel Biochemical Properties of an ATP-Dependent Aliphatic Ketone Carboxylase

Science.gov (United States)

Schühle, Karola

2012-01-01

The anaerobic and aerobic metabolism of acetone and butanone in the betaproteobacterium “Aromatoleum aromaticum” is initiated by their ATP-dependent carboxylation to acetoacetate and 3-oxopentanoic acid, respectively. Both reactions are catalyzed by the same enzyme, acetone carboxylase, which was purified and characterized. Acetone carboxylase is highly induced under growth on acetone or butanone and accounts for at least 5.5% of total cell protein. The enzyme consists of three subunits of 85, 75, and 20 kDa, respectively, in a (αβγ)2 composition and contains 1 Zn and 2 Fe per heterohexamer but no organic cofactors. Chromatographic analysis of the ATP hydrolysis products indicated that ATP was exclusively cleaved to AMP and 2 Pi. The stoichiometry was determined to be 2 ATP consumed per acetone carboxylated. Purified acetone carboxylase from A. aromaticum catalyzes the carboxylation of acetone and butanone as the only substrates. However, the enzyme shows induced (uncoupled) ATPase activity with many other substrates that were not carboxylated. Acetone carboxylase is a member of a protein family that also contains acetone carboxylases of various other organisms, acetophenone carboxylase of A. aromaticum, and ATP-dependent hydantoinases/oxoprolinases. While the members of this family share several characteristic features, they differ with respect to the products of ATP hydrolysis, subunit composition, and metal content. PMID:22020645

Rapid and selective detection of acetone using hierarchical ZnO gas sensor for hazardous odor markers application.

Science.gov (United States)

Jia, Qianqian; Ji, Huiming; Zhang, Ying; Chen, Yalu; Sun, Xiaohong; Jin, Zhengguo

2014-07-15

Hierarchical nanostructured ZnO dandelion-like spheres were synthesized via solvothermal reaction at 200°C for 4h. The products were pure hexagonal ZnO with large exposure of (002) polar facet. Side-heating gas sensor based on hierarchical ZnO spheres was prepared to evaluate the acetone gas sensing properties. The detection limit to acetone for the ZnO sensor is 0.25ppm. The response (Ra/Rg) toward 100ppm acetone was 33 operated at 230°C and the response time was as short as 3s. The sensor exhibited remarkable acetone selectivity with negligible response toward other hazardous gases and water vapor. The high proportion of electron depletion region and oxygen vacancies contributed to high gas response sensitivity. The hollow and porous structure of dandelion-like ZnO spheres facilitated the diffusion of gas molecules, leading to a rapid response speed. The largely exposed (002) polar facets could adsorb acetone gas molecules easily and efficiently, resulting in a rapid response speed and good selectivity of hierarchical ZnO spheres gas sensor at low operating temperature. Copyright © 2014 Elsevier B.V. All rights reserved.

Investigation of regional cerebral blood flow in alcoholic Korsakoff's syndrome with 123I-IMP SPECT

International Nuclear Information System (INIS)

Nakamura, Makoto; Nomura, Soichiro; Kato, Motoichiro; Nakazawa, Tsuneyuki.

1995-01-01

Regional cerebral blood flow (rCBF) was determined quantitatively by single photon emission computed tomography (SPECT) using N-isopropyl-p-[ 123 I]iodoamphetamine ( 123 I-IMP) in 6 patients with alcoholic Korsakoff's syndrome (A group). The findings were compared with concurrently available findings from 6 alcoholic patients with no evidence of cerebral disordres such as Korsakoff's syndrome and dementia (B group) and 4 healthy persons (C group). In both A and B groups, diffuse decrease in blood flow was significantly observed in the entire brain, as compared with the C group; no significant difference in the decreased blood flow existed between the A and B groups. According to the WAIS results, the patients in the A group were classified as 'typical Korsakoff's syndrome' (full IQ of 90 or more) and as 'serious Korsakoff's syndrome' (full IQ of 89 or less). rCBF in the thalamus was significantly lower in the A group of patients with typical Korsakoff's syndrome than the B group. These findings may reflect the variety of alcoholic Korsakoff's syndrome. This may also have an implication for the possible classification of several types in this syndrome. (N.K.)

Metal-Exchanged β Zeolites as Catalysts for the Conversion of Acetone to Hydrocarbons

Directory of Open Access Journals (Sweden)

Aurora J. Cruz-Cabeza

2012-01-01

Full Text Available Various metal-β zeolites have been synthesized under similar ion-exchange conditions. During the exchange process, the nature and acid strength of the used cations modified the composition and textural properties as well as the Brönsted and Lewis acidity of the final materials. Zeolites exchanged with divalent cations showed a clear decrease of their surface Brönsted acidity and an increase of their Lewis acidity. All materials were active as catalysts for the transformation of acetone into hydrocarbons. Although the protonic zeolite was the most active in the acetone conversion (96.8% conversion, the metal-exchanged zeolites showed varied selectivities towards different products of the reaction. In particular, we found the Cu-β to have a considerable selectivity towards the production of isobutene from acetone (over 31% yield compared to 7.5% of the protonic zeolite. We propose different reactions mechanisms in order to explain the final product distributions.

Shock-Tube Measurement of Acetone Dissociation Using Cavity-Enhanced Absorption Spectroscopy of CO.

Science.gov (United States)

Wang, Shengkai; Sun, Kai; Davidson, David F; Jeffries, Jay B; Hanson, Ronald K

2015-07-16

A direct measurement for the rate constant of the acetone dissociation reaction (CH3COCH3 = CH3CO + CH3) was conducted behind reflected shock wave, utilizing a sub-ppm sensitivity CO diagnostic achieved by cavity-enhanced absorption spectroscopy (CEAS). The current experiment eliminated the influence from secondary reactions and temperature change by investigating the clean pyrolysis of <20 ppm acetone in argon. For the first time, the acetone dissociation rate constant (k1) was directly measured over 5.5 orders of magnitude with a high degree of accuracy: k1 (1004-1494 K, 1.6 atm) = 4.39 × 10(55) T(-11.394) exp(-52 140K/T) ± 24% s(-1). This result was seen to agree with most previous studies and has bridged the gap between their temperature and pressure conditions. The current work also served as an example demonstration of the potential of using the CEAS technique in shock-tube kinetics studies.

Nitrogen-Containing Functional Groups-Facilitated Acetone Adsorption by ZIF-8-Derived Porous Carbon

Directory of Open Access Journals (Sweden)

Liqing Li

2018-01-01

Full Text Available Nitrogen-doped porous carbon (ZC is prepared by modification with ammonia for increasing the specific surface area and surface polarity after carbonization of zeolite imidazole framework-8 (ZIF-8. The structure and properties of these ZCs were characterized by Transmission electron microscopy, X-ray diffraction, N2 sorption, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. Through static adsorption tests of these carbons, the sample obtained at 600 °C was selected as an excellent adsorbent, which exhibited an excellent acetone capacity of 417.2 mg g−1 (25 °C with a very large surface area and high-level nitrogen doping (13.55%. The microporosity, surface area and N-containing groups of the materials, pyrrolic-N, pyridinic-N, and oxidized-N groups in particular, were found to be the determining factors for acetone adsorption by means of molecular simulation with density functional theory. These findings indicate that N-doped microporous carbon materials are potential promising adsorbents for acetone.

Problems induced by the use of acetone as a solvent to dose chlorpyrifos in a microecosystem

NARCIS (Netherlands)

Kersting, K.

1995-01-01

Recycling aquatic microecosystems consisting of three subsystems with a total volume of 7.5 L were used to study the effects of the insecticide chlorpyrifos. The poorly soluble chlorpyrifos was dosed dissolved in 0.5 ml of acetone. Acetone was found to be responsible for some of the observed

Electrooxidation of C{sub 1} to C{sub 3} alcohols with Pt and Pt-Ru sputter deposited interdigitated array electrodes

Energy Technology Data Exchange (ETDEWEB)

Lee, Choong-Gon [Department of Chemical Engineering, Faculty of Engineering, Hanbat National University, San 16-1, Dukmyeong-dong, Yuseong-gu, Daejeon 305-719 (Korea, Republic of)], E-mail: leecg@hanbat.ac.kr; Ojima, Hiroyuki [Department of Applied Chemistry, Graduate School of Engineering, Tohoku University, Aramaki-Aoba 07, Aoba-ku, Sendai 980-8579 (Japan); Umeda, Minoru [Department of Materials Science and Technology, Faculty of Engineering, Nagaoka University of Technology, Kamitomioka 1603-1, Nagaoka, Niigata 940-2188 (Japan)], E-mail: mumeda@vos.nagaokaut.ac.jp

2008-02-25

The electrooxidation of methanol, ethanol, and 2-propanol was investigated with interdigitated array electrodes (IDAEs). The IDAE oxidizes alcohol at the generator and reduces the reaction intermediates produced by the oxidation process at the collector. Thus, the reaction intermediates can be estimated with the IDAE. The IDAE in the present work was made of sputter deposited Pt and Pt-Ru. The use of Ru free and added electrodes provides information on the effect of Ru addition on the alcohol oxidation. Cyclic voltammetric analyses revealed that Ru addition enhances the oxidation currents and reduces the E{sub onset} of the alcohols. The detectable reaction intermediate at the methanol and ethanol oxidation was proton, while the intermediate species was acetone in 2-propnaol oxidation.

SPECT brain imaging with N-isopropyl [123I]-p-iodoamphetamine

International Nuclear Information System (INIS)

Holman, B.L.; Hill, T.C.; Magistretti, P.L.

1985-01-01

N-isopropyl-[ 123 I]-p-iodoamphetamine is a lipophilic tracer that passes readily across the blood-brain barrier and is retained long enough to permit planar and tomographic imaging. Its distribution in the brain is proportional to blood flow, and its brain concentration remains unchanged between 30 min and 1 hr after intravenous injection. Tomographic imaging demonstrates increased activity in the gray matter, basal ganglia, and thalamus as would be expected with a cerebral perfusion tracer. In patients with acute cerebral infarction, decreased perfusion occurs immediately with the onset of symptoms. The technique also has utility in epilepsy in defining the abnormal focus in patients with medically intractable temporal-lobe epilepsy. This technique should prove to be a routine nuclear medicine procedure for the evaluation of cerebral perfusion

Correlation of vapor - liquid equilibrium data for acetic acid - isopropanol - water - isopropyl acetate mixtures

Directory of Open Access Journals (Sweden)

B. A. Mandagarán

2006-03-01

Full Text Available A correlation procedure for the prediction of vapor - liquid equilibrium of acetic acid - isopropanol - water - isopropyl acetate mixtures has been developed. It is based on the NRTL model for predicting liquid activity coefficients, and on the Hayden-O'Connell second virial coefficients for predicting the vapor phase of systems containing association components. When compared with experimental data the correlation shows a good agreement for binary and ternary data. The correlation also shows good prediction for reactive quaternary data.

Volatile Organic Compounds (VOCs) in the Ambient Air Of Concentration Unit of Sar-Cheshmeh Copper Complex

International Nuclear Information System (INIS)

Faghihi-Zrandi, A.; Akhgar, M. R.

2016-01-01

Air pollutants including gases, vapors and particles, are emitted from different sources. Volatile organic compounds are the most important pollutants in the ambient air of industries. The present study was carried out to identify and measurement of volatile organic compounds in concentration unit of Sar-Cheshmeh Copper Complex. In this study, sampling of the volatile organic compounds was done by using activated charcoal tube. To identify and measure these compounds gas chromatography/mass spectroscopy were used. Thirteen volatile organic compounds were identified in the ambient air of concentration unit. Among these compounds, the mean value and maximum concentration of isopropyl alcohol and nonane were 255, 640 μg/m3 and 1577, 14400 μg/m3, respectively. By using SPSS software and independent sample t- test, showed that there were no significant difference between mean value concentration of isopropyl alcohol and nonane in the ambient air and TLV values of these compounds (isopropyl alcohol; 200 ppm and nonane; 200 ppm) (P >0.05).

Desolventizing of soybean oil/azeotrope mixtures using ceramic membranes.

Science.gov (United States)

de Melo, Jonas R M; Tiggeman, Lidia; Rezzadori, Katia; Steffens, Juliana; Palliga, Marshall; Oliveira, J Vladimir; Di Luccio, Marco; Tres, Marcus V

2017-08-01

This work investigates the use of ceramic membranes with different molecular weight cut-offs (MWCOs: 5, 10 and 20 kDa) to desolventize azeotropic solvent mixtures (ethanol/n-hexane and isopropyl alcohol/n-hexane) from soybean oil/azeotrope micelles. Results show that a decrease in the MWCO of a membrane and an increase in the solvent mass ratio in the mixture resulted in a significant reduction in the permeate flux. The 20 kDa membrane presented the highest permeate flux, 80 and 60 kg/m 2 h for the soybean oil/n-hexane/isopropyl alcohol and soybean oil/n-hexane/ethanol azeotropes, respectively, for an oil to solvent ratio of 1:3 (w/w). The highest oil retention was found using the n-hexane/isopropyl alcohol azeotrope, around 25% in the membrane with the lowest MWCO, that is, 5 kDa. It is shown that the azeotropic mixtures provided intermediate characteristics compared to the original pure solvent behavior.

Biological activities of Umbilicaria crustulosa (Ach. frey acetone extract

Directory of Open Access Journals (Sweden)

Zlatanović Ivana

2017-01-01

Full Text Available This paper reports for the first time the effect of an acetone extract of Umbilicaria crustulosa on the micronucleus distribution of human lymphocytes, and on the cholinesterase activity and antioxidant activity by the cupric ion reducing antioxidant capacity (CUPRAC method. Additionally, the total phenolic compounds (TPC and the antioxidant properties were estimated via DPPH, ABTS and TRP assays. Moreover, the antibacterial activity against two Gram-positive and three Gram-negative bacteria were determined. Acetone extract of U. crustulosa at concentration of 1 and 2 μg mL-1 decreased a frequency of micronuclei (MN by 10.8 and 16.8 %, respectively, acting more or slightly less than the synthetic protector amifostine (AMF, WR-2721, 11.4 %, at concentration of 1 μg mL-1. The tested extract did not inhibit cholinesterase activity nor did it exhibit activity toward the examined bacteria. The extract reduced the concentration of DPPH and ABTS radicals by 88.7 and 96.2 %, respectively. Values for total reducing power (TRP and cupric reducing capacity (CUPRAC were 0.6197±0.0166 μg ascorbic acid equivalents (AAE per mg of dry extract, and 19.7641±1.6546 μg trolox equivalents (TE per mg of dry extract, respectively. The total phenol content was 350.4188 ±14.587 μg gallic acid equivalents (GAE per mg of dry extract. The results of the present study showed that U. crustulosa acetone extract is a promising candidate for in vivo experiments considering its antioxidant activity and protective effect on human lymphocytes. [Projekat Ministarstva nauke Republike Srbije, br. 172047

Theoretical studies of mechanisms of cycloaddition reaction between difluoromethylene carbene and acetone

Science.gov (United States)

Lu, Xiu Hui; Yu, Hai Bin; Wu, Wei Rong; Xu, Yue Hua

Mechanisms of the cycloaddition reaction between singlet difluoromethylene carbene and acetone have been investigated with the second-order Møller-Plesset (MP2)/6-31G* method, including geometry optimization and vibrational analysis. Energies for the involved stationary points on the potential energy surface (PES) are corrected by zero-point energy (ZPE) and CCSD(T)/6-31G* single-point calculations. From the PES obtained with the CCSD(T)//MP2/6-31G* method for the cycloaddition reaction between singlet difluoromethylene carbene and acetone, it can be predicted that path B of reactions 2 and 3 should be two competitive leading channels of the cycloaddition reaction between difluoromethylene carbene and acetone. The former consists of two steps: (i) the two reactants first form a four-membered ring intermediate, INT2, which is a barrier-free exothermic reaction of 97.8 kJ/mol; (ii) the intermediate INT2 isomerizes to a four-membered product P2b via a transition state TS2b with an energy barrier of 24.9 kJ/mol, which results from the methyl group transfer. The latter proceeds in three steps: (i) the two reactants first form an intermediate, INT1c, through a barrier-free exothermic reaction of 199.4 kJ/mol; (ii) the intermediate INT1c further reacts with acetone to form a polycyclic intermediate, INT3, which is also a barrier-free exothermic reaction of 27.4 kJ/mol; and (iii) INT3 isomerizes to a polycyclic product P3 via a transition state TS3 with an energy barrier of 25.8 kJ/mol.

Detection and sensing mechanism of acetone with modeling using Pd/TiO{sub 2}/Si structure

Energy Technology Data Exchange (ETDEWEB)

Yadava, Lallan, E-mail: nisaly06@rediffmail.com; Verma, Ritesh; Singh, Ravi S.

2012-01-31

A grided Pd/TiO{sub 2}/Si (Pdtisin) gas sensor is fabricated to detect hydrocarbons such as acetone, ethanol and trichloroethylene. The sensitivity measurements are carried out in various ambient (O{sub 2}, N{sub 2} and Ar) at room temperature which revealed that fabricated structure attains maximal response for acetone in contrast to other vapors examined. The study of ambient-effect on the device shows that it out-performs in oxygen ambient. A catalytic oxidation mechanism for detection of acetone with a model based upon Langmuir law of adsorption and Frenkel-Poole theory of electronic emission for the description of sensing behavior and vindication of experimental results have been proposed.

Graphene oxide foams and their excellent adsorption ability for acetone gas

International Nuclear Information System (INIS)

He, Yongqiang; Zhang, Nana; Wu, Fei; Xu, Fangqiang; Liu, Yu; Gao, Jianping

2013-01-01

Graphical abstract: - Highlights: • GO and RGO foams were prepared using a simple and green method, unidirectional freeze-drying. • The porous structure of the foams can be adjusted by changing GO concentrations. • GO and RGO foams show good adsorption efficiency for acetone gas. - Abstract: Graphene oxide (GO) and reduced graphene oxide (RGO) foams were prepared using a unidirectional freeze-drying method. These porous carbon materials were characterized by thermal gravimetric analysis, differential scanning calorimetry, X-ray photoelectron spectroscopy and scanning electron microscopy. The adsorption behavior of the two kinds of foams for acetone was studied. The result showed that the saturated adsorption efficiency of the GO foams was over 100%, and was higher than that of RGO foams and other carbon materials

Determination of acetone in saliva by reversed-phase liquid chromatography with fluorescence detection and the monitoring of diabetes mellitus patients with ketoacidosis.

Science.gov (United States)

Fujii, Shinya; Maeda, Toshio; Noge, Ichiro; Kitagawa, Yutaka; Todoroki, Kenichiro; Inoue, Koichi; Min, Jun Zhe; Toyo'oka, Toshimasa

2014-03-20

In diabetes mellitus (DM) patients with ketoacidosis, ketone bodies, i.e., acetone, acetoacetic acid (AA) and β-hydroxybutyric acid (HA), are increased in the blood and urine. Acetone is also excreted by breathing due to the spontaneous decomposition of AA. Thus, the increase in acetone has been considered as one of the biomarkers for the diagnosis of DM. However, the determination of acetone in one's breath is not recommended because of the sample handling difficulty. We measured acetone in saliva by reversed-phase liquid chromatography (LC) with fluorescence (FL) detection. The proposed method was applied to the determination of acetone in the saliva of healthy volunteers and DM patients with and without ketoacidosis. 3-Pentanone (I.S.) and DBD-H in acetonitrile were added to freshly collected saliva and reacted at room temperature for 20 min in the presence of trifluoroacetic acid. After the reaction, the solution was centrifuged at 10,000 × g and 4 °C for 5 min. The supernatant was separated by reversed-phase LC and the FL detected at 550 nm (excitation at 460 nm). The concentrations of acetone in the DM patients with ketoacidosis were significantly higher than those of the normal subjects and DM patients without ketoacidosis. Furthermore, the total contents of the ketone bodies in the blood correlated with acetone in the saliva of the DM patients. The concentrations of acetone in the saliva of an emergency patient also correlated with the ketone bodies in the blood at each sampling time. The proposed method using LC-FL seems to be useful for the determination of acetone in the saliva of DM patients with ketoacidosis. The method offers a new option for the diagnosis and monitoring of DM patients with ketoacidosis. Copyright © 2014 Elsevier B.V. All rights reserved.

Crystal morphology modification by the addition of tailor-made stereocontrolled poly(N-isopropyl acrylamide)

DEFF Research Database (Denmark)

Munk, Tommy; Baldursdottir, Stefania; Hietala, Sami

2012-01-01

. One such additive is the thermosensitive polymer poly(N-isopropyl acrylamide) (PNIPAM). The use of PNIPAM as a crystallization additive provides a possibility to affect viscosity at separation temperatures and nucleation and growth rates at higher temperatures. In this study, novel PNIPAM derivatives......; the morphology of crystals changed from needle to dendritic shape. Additionally, the amphiphilic nature of PNIPAM increased the solubility of nitrofurantoin in water. PNIPAMs with varying molecular weights and stereoregularities resulted in similar changes in the crystal habit of the drug regardless of whether...

Effects of supplementation with 2-hydroxy-4-(methylthio)-butanoic acid isopropyl ester on splanchnic amino acid metabolism and essential amino acid mobilization in postpartum transition Holstein cows

DEFF Research Database (Denmark)

Dalbach, Kristine Foged; Larsen, Mogens; Raun, Birgitte Marie Løvendahl

2011-01-01

The present study aimed to investigate the effects of 2-hydroxy-4-(methylthio)-butanoic acid isopropyl ester (HMBi) supplementation on splanchnic AA metabolism, essential AA (EAA) mobilization, and plasma AA status in postpartum transition dairy cows. The EAA mobilization was calculated by differ......The present study aimed to investigate the effects of 2-hydroxy-4-(methylthio)-butanoic acid isopropyl ester (HMBi) supplementation on splanchnic AA metabolism, essential AA (EAA) mobilization, and plasma AA status in postpartum transition dairy cows. The EAA mobilization was calculated...

A Sub-ppm Acetone Gas Sensor for Diabetes Detection Using 10 nm Thick Ultrathin InN FETs

Science.gov (United States)

Kao, Kun-Wei; Hsu, Ming-Che; Chang, Yuh-Hwa; Gwo, Shangjr; Yeh, J. Andrew

2012-01-01

An indium nitride (InN) gas sensor of 10 nm in thickness has achieved detection limit of 0.4 ppm acetone. The sensor has a size of 1 mm by 2.5 mm, while its sensing area is 0.25 mm by 2 mm. Detection of such a low acetone concentration in exhaled breath could enable early diagnosis of diabetes for portable physiological applications. The ultrathin InN epilayer extensively enhances sensing sensitivity due to its strong electron accumulation on roughly 5–10 nm deep layers from the surface. Platinum as catalyst can increase output current signals by 2.5-fold (94 vs. 37.5 μA) as well as reduce response time by 8.4-fold (150 vs. 1,260 s) in comparison with bare InN. More, the effect of 3% oxygen consumption due to breath inhalation and exhalation on 2.4 ppm acetone gas detection was investigated, indicating that such an acetone concentration can be analyzed in air. PMID:22969342

A Negative Correlation Between Blood Glucose and Acetone Measured in Healthy and Type 1 Diabetes Mellitus Patient Breath.

Science.gov (United States)

Rydosz, Artur

2015-07-01

Exhaled acetone analysis has long been recognized as a supplementary tool for diagnosis and monitoring diabetes, especially type 1 diabetes. It is essential, therefore to determine the relationship between exhaled acetone concentration and glucose in blood. Usually, a direct linear correlation between this both compounds has been expected. However, in some cases we can observe a reverse correlation. When blood glucose was increasing, breath acetone declined. The breath analysis as a supplementary tool for diagnosing and monitoring diabetes makes sense only in case of utilization of portable analyzers. This need has created a market for gas sensors. However, commercially available acetone gas sensors are developed for measuring samples at several tens part per million. The exhaled acetone concentration was measured using commercial acetone gas sensor (TGS 822, 823 Figaro, Arlington Heights, IL, USA Inc) with micropreconcentrator in low temperature cofired ceramics. The reference analyzer-mass spectrometry (HPR-20 QIC, Hiden Analytical, Warrington, UK) was used. Twenty-two healthy volunteers with no history of any respiratory disease participated in the research, as did 31 patients diagnosed with type 1 diabetes. Respectively, 3 healthy volunteer and 5 type 1 diabetes mellitus subjects with reverse trend were selected. The linear fitting coefficient various from 0.1139 to 0.9573. Therefore, it is necessary to determine the correlation between blood glucose concentrations and under different conditions, for example, insulin levels, as well as correlate the results with clinical tests, for example, Hb1Ac. It is well known that the concentration of acetone is strongly influenced by diet, insulin treatment, and so on. Therefore, much more complex analysis with long-term measurements are required. Thus, presented results should be regarded as tentative, and validation studies with the analysis of clinical test and in a large number of patients, including control groups

Electron spectra and mechanism of complexing of uranyl nitrate in water-acetone solutions

International Nuclear Information System (INIS)

Zazhogin, A.A.; Zazhogin, A.P.; Komyak, A.I.; Serafimovich, A.I.

2003-01-01

Based on the analysis of the luminescence and electronic absorption spectra, the processes of complexing in an aqueous solution of UO 2 (NO 3 ) 2 ·6H 2 O with small additions of acetone have been studied. In a pure aqueous solution, uranyl exists as the complex UO 2 ·5H 2 O. It is shown that the addition of acetone to the solution leads to the displacement of some water molecules out of the first coordination sphere of uranyl and the formation of the uranyl nitrate dihydrate complexes UO 2 (NO 3 ) 2 ·2H 2 O. It has been established that the stability of these complexes is determined by the decrease in the water activity and in the degree of hydration of uranyl and nitrate, which is the result of the local increase in the concentration of acetone molecules (due to their hydrophobicity) in the regions of the solution where uranyl and nitrate ions are found. The experimental facts supported the mechanism proposed are presented. (authors)

Sensitive and selective cataluminescence-based sensor system for acetone and diethyl ether determination.

Science.gov (United States)

Wang, Qihui; Li, Bo; Wang, Yuhuai; Shou, Zhouxiang; Shi, Guolong

2015-05-01

A three-dimensional hierarchical CdO nanostructure with a novel bio-inspired morphology is reported. The field emission scanning electronic microscopy, transmission electron microscopy and X-ray diffractometer were employed to characterize the as-prepared samples. In gas-sensing measurements, acetone and diethyl ether were employed as target gases to investigate cataluminescence (CTL) sensing properties of the CdO nanostructure. The results show that the as-fabricated CdO nanostructure exhibited outstanding CTL properties such as stable intensity, high signal/noise values, short response and recovery time. The limit of detection of acetone and diethyl ether was ca. 6.5 ppm and 6.7 ppm, respectively, which was below the standard permitted concentrations. Additionally, a principal components analysis method was used to investigate the recognizable ability of the CTL sensor, and it was found that acetone and diethyl ether can be distinguished clearly. The performance of the bio-inspired CdO nanostructure-based sensor system suggested the promising application of the CdO nanostructure as a novel highly efficient CTL sensing material. Copyright © 2014 John Wiley & Sons, Ltd.

The results of the toxicity and hazard studies of isopropyl meta-carborane with single administration to laboratory animals

Directory of Open Access Journals (Sweden)

Yushkov G.G.

2018-04-01

Full Text Available Intensive research on the chemistry of borohydrides and the creation of high-energy fuels led to the discovery of a completely new type of organoboron compounds, which were collectively called carboranes. Taking into account the scope of application of organoboron compounds in various branches of human economic activity, we present for publication the quantitative data of a toxicological study of the higher isomer of carboranes of isopropyl meta-carborane at the level of a single injection into the laboratory animals through the mouth and lungs. Background. Supplementing data on toxicity and the hazard of organoboron compounds requires the study of the response of the organism to the action of isopropyl meta-carborane. The purpose of the study: identification of possible features and specificity of the toxic effect of carboranes on the example of isopropyl meta-carborane. Methods. The object of the study is nonlinear laboratory animals: rats, mice and rabbits contained in standard vivarium conditions, with observance of the rules of humane treatment of animals. Traditional methods of research (physiological, hematological, morphological have been used. Statistical processing of data was carried out using the programs «Microsoft Office Excel 2007» and «Biostat». Differences were considered statistically significant at p ≤ 0.05, using a parametric test. Results. Acute toxicity parameters were obtained, which allowed the substance to be classified as moderately hazardous (3rd hazard class according to GOST 12.1.007, which does not have selective irritant, pneumotoxic and fibrogenic effects. Conclusion. Thus, the predominant influence of the substance is established objectively with a single exposure to the blood system as its toxicological feature, and its effect on spermatozoa is a specificity of the action, which stimulates the study of this carborane under conditions of chronic administration to the animals.

Synthesis, labelling and biodistribution of N-isopropyl 131I-p-iodoamhetamine (131IAMP)

International Nuclear Information System (INIS)

Godoy, N.; Reveco, P.; Mena, P.; Gil, M.C.

1986-01-01

It is possible to synthesize N-isopropyl-p-iodoamphetamine (IAMP) through differents schemes, being the most feasible the iodination of phenylacetic acid. The labelling of this compound with radioidine, by isotope exchange in presence or absence of Cu (II) as catalyst, presents less activity concentration in brain than using Cu (II) with an excess of ascorbic acid as reducing agent of Cu (II). The use of ascorbic acid in excess allow the formation of Cu (I) in-situ, which may form an Ar-Cu-I complex, favouring the isotope nucleophilic substitution reaction, obtaining 131 IAMP higher radiochemical purity and better cerebral uptake. (Author)

Extraction of Oxytetracycline Hydrochloride in Aqueous Two-phase System of Acetone and Ammonium Sulfate

International Nuclear Information System (INIS)

Han, J.

2013-01-01

Summary: Aqueous two-phase system (ATPS) is an efficient implement for separation of various substrates, and extracted by an aqueous two-phase system has been successful ly applied in the downstream processing of various biological compounds. In this research, the extraction of oxytetracycline hydrochloride (OTC-HCl) was carried out in an aqueous two-phase system containing acetone and ammonium sulfate solution, which partitioned the antibiotic to the upper phase. The effects of some parameters on the extraction efficiency of OTC-HCl were studied in detail, including temperature, the volume of acetone, the pH value of ammonium sulfate solution, the concentrations of (NH/sub 4/)/sub 2/ SO/sub 4/ and OTC-HCl. The results showed that the volume of acetone, the pH value of ammonium sulfate solution and the concentration of OTC-HCl in feed had significant effects on the extraction efficiency of OTC-HCl, but the effects of temperature on the extraction of OTC-HCl was not obvious. (author)

Extraction of Oxytetracycline Hydrochloride in Aqueous Two-phase System of Acetone and Ammonium Sulfate

Energy Technology Data Exchange (ETDEWEB)

Han, J. [Jiangsu Univ., Zhenjiang (China). Dept. of Food and Biological Engineering

2013-02-15

Summary: Aqueous two-phase system (ATPS) is an efficient implement for separation of various substrates, and extracted by an aqueous two-phase system has been successful ly applied in the downstream processing of various biological compounds. In this research, the extraction of oxytetracycline hydrochloride (OTC-HCl) was carried out in an aqueous two-phase system containing acetone and ammonium sulfate solution, which partitioned the antibiotic to the upper phase. The effects of some parameters on the extraction efficiency of OTC-HCl were studied in detail, including temperature, the volume of acetone, the pH value of ammonium sulfate solution, the concentrations of (NH/sub 4/)/sub 2/ SO/sub 4/ and OTC-HCl. The results showed that the volume of acetone, the pH value of ammonium sulfate solution and the concentration of OTC-HCl in feed had significant effects on the extraction efficiency of OTC-HCl, but the effects of temperature on the extraction of OTC-HCl was not obvious. (author)

Inhalation developmental toxicology studies: Teratology study of acetone in mice and rats: Final report

Energy Technology Data Exchange (ETDEWEB)

Mast, T.J.; Evanoff, J.J.; Rommereim, R.L.; Stoney, K.H.; Weigel, R.J.; Westerberg, R.B.

1988-11-01

Acetone, an aliphatic ketone, is a ubiquitous industrial solvent and chemical intermediate; consequently, the opportunity for human exposure is high. The potential for acetone to cause developmental toxicity was assessed in Sprague-Dawley rats exposed to 0, 440, 2200, or 11000 ppm, and in Swiss (CD-1) mice exposed to 0, 440, 2200, and 6600 ppm acetone vapors, 6 h/day, 7 days/week. Each of the four treatment groups consisted of 10 virgin females (for comparison), and approx.32 positively mated rats or mice. Positively mated mice were exposed on days 6-17 of gestation (dg), and rats on 6-19 dg. The day of plug or sperm detection was designated as 0 dg. Body weights were obtained throughout the study period, and uterine and fetal body weights were obtained at sacrifice (rats, 20 dg; mice, 18 dg). Implants were enumerated and their status recorded. Live fetuses were sexed and examined for gross, visceral, skeletal, and soft-tissue craniofacial defects. 46 refs., 6 figs., 27 tabs.

Oxidative polymerization of lignins by laccase in water-acetone mixture.

Science.gov (United States)

Fiţigău, Ionița Firuța; Peter, Francisc; Boeriu, Carmen Gabriela

2013-01-01

The enzymatic oxidative polymerization of five technical lignins with different molecular properties, i.e. Soda Grass/Wheat straw Lignin, Organosolv Hardwood Lignin, Soda Wheat straw Lignin, Alkali pretreated Wheat straw Lignin, and Kraft Softwood was studied. All lignins were previously fractionated by acetone/water 50:50 (v/v) and the laccase-catalyzed polymerization of the low molecular weight fractions (Mw Reactivity of lignin substrates in laccase-catalyzed reactions was determined by monitoring the oxygen consumption. The oxidation reactions in 50% acetone in water mixture proceed with high rate for all tested lignins. Polymerization products were analyzed by size exclusion chromatography, FT-IR, and (31)P-NMR and evidence of important lignin modifications after incubation with laccase. Lignin polymers with higher molecular weight (Mw up to 17500 g/mol) were obtained. The obtained polymers have potential for applications in bioplastics, adhesives and as polymeric dispersants.

Investigation of regional cerebral blood flow in alcoholic Korsakoff`s syndrome with {sup 123}I-IMP SPECT

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Makoto; Nomura, Soichiro [Tachikawa Hospital, Tokyo (Japan); Kato, Motoichiro; Nakazawa, Tsuneyuki

1995-05-01

Regional cerebral blood flow (rCBF) was determined quantitatively by single photon emission computed tomography (SPECT) using N-isopropyl-p-[{sup 123}I]iodoamphetamine ({sup 123}I-IMP) in 6 patients with alcoholic Korsakoff`s syndrome (A group). The findings were compared with concurrently available findings from 6 alcoholic patients with no evidence of cerebral disordres such as Korsakoff`s syndrome and dementia (B group) and 4 healthy persons (C group). In both A and B groups, diffuse decrease in blood flow was significantly observed in the entire brain, as compared with the C group; no significant difference in the decreased blood flow existed between the A and B groups. According to the WAIS results, the patients in the A group were classified as `typical Korsakoff`s syndrome` (full IQ of 90 or more) and as `serious Korsakoff`s syndrome` (full IQ of 89 or less). rCBF in the thalamus was significantly lower in the A group of patients with typical Korsakoff`s syndrome than the B group. These findings may reflect the variety of alcoholic Korsakoff`s syndrome. This may also have an implication for the possible classification of several types in this syndrome. (N.K.).

Synthesis and evaluation of inhaled [11C]butane and intravenously injected [11C]acetone as potential radiotracers for studying inhalant abuse

International Nuclear Information System (INIS)

Gerasimov, Madina R.; Ferrieri, Richard A.; Pareto, Deborah; Logan, Jean; Alexoff, David; Ding Yushin

2005-01-01

The phenomenon of inhalant abuse is a growing problem in the US and many countries around the world. Yet, relatively little is known about the pharmacokinetic properties of inhalants that underlie their abuse potential. While the synthesis of 11 C-labeled toluene, acetone and butane has been proposed in the literature, none of these compounds has been developed as radiotracers for PET studies. In the present report we extend our previous studies with [ 11 C]toluene to include [ 11 C]acetone and [ 11 C]butane with the goal of comparing the pharmacokinetic profiles of these three volatile abused substances. Both [ 11 C]toluene and [ 11 C]acetone were administered intravenously and [ 11 C]butane was administered via inhalation to anesthesized baboons. Rapid and efficient uptake of radiolabeled toluene and acetone into the brain was followed by fast clearance in the case of toluene and slower kinetics in the case of acetone. [ 11 C]Butane was detected in the blood and brain following inhalation, but the levels of radioactivity in both tissues dropped to half of the maximal values over the period of less than a minute. To our knowledge, this is the first reported study of the in vivo brain pharmacokinetics of labeled acetone and butane in nonhuman primates. These data provide insight into the pharmacokinetic features possibly associated with the abuse liability of toluene, acetone and butane

Chemical reactions in the nitrogen-acetone ice induced by cosmic ray analogues: relevance for the Solar system

Science.gov (United States)

de Barros, A. L. F.; Andrade, D. P. P.; da Silveira, E. F.; Alcantara, K. F.; Boduch, P.; Rothard, H.

2018-02-01

The radiolysis of 10:1 nitrogen:acetone mixture, condensed at 11 K, by 40 MeV 58Ni11 + ions is studied. These results are representative of studies concerning Solar system objects, such as transneptunian objects, exposed to cosmic rays. Bombardment by cosmic rays triggers chemical reactions leading to synthesis of larger molecules. In this work, destruction cross-sections of acetone and nitrogen molecules in solid phase are determined and compared with those for pure acetone. The N2 column density decreases very fast indicating that, under irradiation, nitrogen leaves quickly a porous sample. The most abundant molecular species formed in the radiolysis are C3H6, C2H6, N3, CO, CH4 and CO2. Some N-bearing species are also formed, but with low production yield. Dissolving acetone in nitrogen decreases the formation cross-sections of CH4, CO2 and H2CO, while increases those for CO and C2H6 species. This fact may explain the presence of C2H6 in Pluto's surface where CH4 is not pure, but diluted in an N2 matrix. The formation of more complex molecules, such as HNCO and, possibly, glycine is observed, suggesting the formation of small prebiotic species in objects beyond Neptune from acetone diluted in a N2 matrix irradiated by cosmic rays.

Use of technetium-99m-di-isopropyl-iminodiacetic acid imaging in the demonstration of a biliary-bronchial fistula

Energy Technology Data Exchange (ETDEWEB)

Savitch, I.; Esser, J.D.; Levin, J. (University of the Witwatersrand, Johannesburg (South Africa). Dept. of Nuclear Medicine); Krige, L.P.; Kew, M.C. (University of the Witwatersrand, Johannesburg (South Africa). Dept. of Medicine)

1984-05-12

A case is described in which technetium-99m-di-isopropyl-iminodiacetic acid imaging was used to trace the passage of bile from its site of leakage into an amoebic liver abscess, through a fistulous tract connecting the liver abscess with an abscess in the right lower lobe of the lung, and into the upper respiratory tract.

Simultaneous determination of methanol, acetaldehyde, acetone, and ethanol in human blood by gas chromatography with flame ionization detection.

Science.gov (United States)

Schlatter, J; Chiadmi, F; Gandon, V; Chariot, P

2014-01-01

Methanol, acetaldehyde, acetone, and ethanol, which are commonly used as biomarkers of several diseases, in acute intoxications, and forensic settings, can be detected and quantified in biological fluids. Gas chromatography (GC)-mass spectrometry techniques are complex, require highly trained personnel and expensive materials. Gas chromatographic determinations of ethanol, methanol, and acetone have been reported in one study with suboptimal accuracy. Our objective was to improve the assessment of these compounds in human blood using GC with flame ionization detection. An amount of 50 µl of blood was diluted with 300 µl of sterile water, 40 µl of 10% sodium tungstate, and 20 µl of 1% sulphuric acid. After centrifugation, 1 µl of the supernatant was injected into the gas chromatograph. We used a dimethylpolysiloxane capillary column of 30 m × 0.25 mm × 0.25 µm. We observed linear correlations from 7.5 to 240 mg/l for methanol, acetaldehyde, and acetone and from 75 to 2400 mg/l for ethanol. Precision at concentrations 15, 60, and 120 mg/l for methanol, acetaldehyde, and acetone and 150, 600, and 1200 mg/ml for ethanol were 0.8-6.9%. Ranges of accuracy were 94.7-98.9% for methanol, 91.2-97.4% for acetaldehyde, 96.1-98.7% for acetone, and 105.5-111.6% for ethanol. Limits of detection were 0.80 mg/l for methanol, 0.61 mg/l for acetaldehyde, 0.58 mg/l for acetone, and 0.53 mg/l for ethanol. This method is suitable for routine clinical and forensic practices.

Thermal and Ablative Properties of Ipns and Composites of High Ortho Resole Resin and Difurfurylidene Acetone

Directory of Open Access Journals (Sweden)

Tariq S. NAJIM

2008-12-01

Full Text Available High ortho resole resin was prepared by condensation of phenol with excess of formaldehyde in the presence of magnesium oxide as catalyst. Reaction of furfuraldehyde with acetone in basic medium led to difurfurylidene acetone (DFA. Their interpenetrating polymer network (IPNS were obtained by the reaction of predetermined quantities of difurfurylidene acetone and high ortho resole using p-toluene sulphonic acid (PTSA as curing agent. The thermal behavior of the resins was studied using thermogravimetry (TG under ambient and nitrogen atmospheres over a temperature range of (25-1000 Cº. It was observed that the IPN of 20% DFA – 80% resole has higher thermal stability than that of resole alone and the decomposition temperature was higher by 80 Cº. This behavior was attributed to highly cross linked structure and thermally stable backbone of ploy difurfurylidene acetone due to formation of ladder structure.Impregnation of chopped fiber glass type (E with the polymeric solutions was used to prepare their composites, and the ablative properties were investigated according to ASTM E-285 –80. It was observed that the IPN of (DFA- resol perform better than the resole composite alone.

Quantitative analysis of O-isopropyl methylphosphonic acid in serum samples of Japanese citizens allegedly exposed to sarin: Estimation of internal dosage

NARCIS (Netherlands)

Noort, D.; Hulst, A.G.; Platenburg, D.H.J.M.; Polhuijs, M.; Benschop, H.P.

1998-01-01

A convenient and rapid micro-anion exchange liquid chromatography (LC) tandem electrospray mass spectrometry (MS) procedure was developed for quantitative analysis in serum of O-isopropyl methylphosphonic acid (IMPA), the hydrolysis product of the nerve agent sarin. The mass spectrometric procedure

Investigation of hybrid plasma-catalytic removal of acetone over CuO/γ-Al2O3 catalysts using response surface method.

Science.gov (United States)

Zhu, Xinbo; Tu, Xin; Mei, Danhua; Zheng, Chenghang; Zhou, Jinsong; Gao, Xiang; Luo, Zhongyang; Ni, Mingjiang; Cen, Kefa

2016-07-01

In this work, plasma-catalytic removal of low concentrations of acetone over CuO/γ-Al2O3 catalysts was carried out in a cylindrical dielectric barrier discharge (DBD) reactor. The combination of plasma and the CuO/γ-Al2O3 catalysts significantly enhanced the removal efficiency of acetone compared to the plasma process using the pure γ-Al2O3 support, with the 5.0 wt% CuO/γ-Al2O3 catalyst exhibiting the best acetone removal efficiency of 67.9%. Catalyst characterization was carried out to understand the effect the catalyst properties had on the activity of the CuO/γ-Al2O3 catalysts in the plasma-catalytic reaction. The results indicated that the formation of surface oxygen species on the surface of the catalysts was crucial for the oxidation of acetone in the plasma-catalytic reaction. The effects that various operating parameters (discharge power, flow rate and initial concentration of acetone) and the interactions between these parameters had on the performance of the plasma-catalytic removal of acetone over the 5.0 wt% CuO/γ-Al2O3 catalyst were investigated using central composite design (CCD). The significance of the independent variables and their interactions were evaluated by means of the Analysis of Variance (ANOVA). The results showed that the gas flow rate was the most significant factor affecting the removal efficiency of acetone, whilst the initial concentration of acetone played the most important role in determining the energy efficiency of the plasma-catalytic process. Copyright © 2016 Elsevier Ltd. All rights reserved.

Acetone improves the topographical homogeneity of liquid phase exfoliated few-layer black phosphorus flakes.

Science.gov (United States)

Gomez Perez, Juan; Konya, Zoltan; Kukovecz, Akos

2018-06-12

Liquid phase exfoliation of 2D materials has issues related to the sorption of the solvent, the oxidation of the sample during storage, and the topographical inhomogeneity of the exfoliated material. N-methyl-2-pyrrolidone (NMP), a common solvent for black phosphorus (BP) exfoliation, has additional drawbacks like the formation of by-products during sonication and poor solvent volatility. Here we demonstrate an improvement in the topographical homogeneity (i.e. thickness and lateral dimensions) of NMP-exfoliated BP flakes after resuspension in acetone. The typical size of monolayers and bilayers stabilised in acetone was 99.8±27.4 nm and 159.1±57 nm, respectively. These standard deviations represent a threefold improvement over those of the NMP-exfoliated originals. Phosphorene can also be exfoliated directly in acetone by very long ultrasonication. The product suspension enjoys the same dimensional homogeneity benefits, which confirms that this effect is an intrinsic property of the acetone-BP system. The quality and stability of the exfoliated flakes was checked by XRD, TEM, electron diffraction and Raman spectroscopy. Thermal expansion coefficients of the A1g, B2g and A2g Raman modes were calculated for drop-casted samples as -0.01828 cm-1/K, -0.03056 cm-1/K and -0.03219 cm-1/K, respectively. The flakes withstand 20 minutes in O2 flow at 373 K without lattice distortion. . © 2018 IOP Publishing Ltd.

Ionic liquid 1-hexyl-3-methylimidazolium hexafluorophosphate, an efficient solvent for extraction of acetone from aqueous solutions

International Nuclear Information System (INIS)

Saien, Javad; Badieh, Marjan Mohammadi Sarab; Norouzi, Mahdi; Salehzadeh, Sadegh

2015-01-01

Highlights: • The use of HMIMPF_6 as a green ionic was feasible in the extraction of acetone from water. • The binodal curves were determined by cloud point measurement method. • High level separation factor of acetone between the ionic liquid and water were achieved. • The thermodynamic properties of HMIMPF_6 were obtained by the Density Functional Theory calculations. • The NRTL and UNIQUAC models were applied satisfactorily to correlate the equilibrium data. - Abstract: (Liquid + liquid) equilibrium (LLE) of the chemical system of {water + acetone + 1-Hexyl-3-methylimidazolium hexafluorophosphate (HMIMPF_6) ionic liquid} was studied at different temperatures of (293.2, 298.2 and 303.2) K and under atmospheric pressure of 81.5 kPa. The results show that HMIMPF_6 provides the acetone distribution coefficient and separation factor values within (0.8813 to 1.2351) and (3.0 to 54.4), respectively; indicating the high capability of the ionic liquid for extraction of acetone from aqueous solutions. In most cases, acetone solubility in the ionic liquid is higher than in water, especially at higher solute concentrations. Meanwhile, higher separation factor is relevant to the lower temperature due to lower (water + ionic liquid) miscibility. The consistency of tie line data, at each temperature, was examined with Othmer–Tobias correlation. The values were nicely reproduced with the well-known NRTL and UNIQUAC models. Accordingly, the required thermodynamic properties of HMIMPF_6 were obtained by the Density Functional Theory (DFT) calculations, carried out at the M06/6-311++G"∗"∗ level of theory. The root mean square deviations (RMSD) between experimental and model concentration values were 0.0192 and 0.0255, respectively; indicating close agreement of the both models.

Electrolytically exfoliated graphene-loaded flame-made Ni-doped SnO2 composite film for acetone sensing.

Science.gov (United States)

Singkammo, Suparat; Wisitsoraat, Anurat; Sriprachuabwong, Chakrit; Tuantranont, Adisorn; Phanichphant, Sukon; Liewhiran, Chaikarn

2015-02-11

In this work, flame-spray-made SnO2 nanoparticles are systematically studied by doping with 0.1-2 wt % nickel (Ni) and loading with 0.1-5 wt % electrolytically exfoliated graphene for acetone-sensing applications. The sensing films (∼12-18 μm in thickness) were prepared by a spin-coating technique on Au/Al2O3 substrates and evaluated for acetone-sensing performances at operating temperatures ranging from 150 to 350 °C in dry air. Characterizations by X-ray diffraction, transmission/scanning electron microscopy, Brunauer-Emmett-Teller analysis, X-ray photoelectron spectroscopy and Raman spectroscopy demonstrated that Ni-doped SnO2 nanostructures had a spheriodal morphology with a polycrystalline tetragonal SnO2 phase, and Ni was confirmed to form a solid solution with SnO2 lattice while graphene in the sensing film after annealing and testing still retained its high-quality nonoxidized form. Gas-sensing results showed that SnO2 sensing film with 0.1 wt % Ni-doping concentration exhibited an optimal response of 54.2 and a short response time of ∼13 s toward 200 ppm acetone at an optimal operating temperature of 350 °C. The additional loading of graphene at 5 wt % into 0.1 wt % Ni-doped SnO2 led to a drastic response enhancement to 169.7 with a very short response time of ∼5.4 s at 200 ppm acetone and 350 °C. The superior gas sensing performances of Ni-doped SnO2 nanoparticles loaded with graphene may be attributed to the large specific surface area of the composite structure, specifically the high interaction rate between acetone vapor and graphene-Ni-doped SnO2 nanoparticles interfaces and high electronic conductivity of graphene. Therefore, the 5 wt % graphene loaded 0.1 wt % Ni-doped SnO2 sensor is a promising candidate for fast, sensitive and selective detection of acetone.

Determination of the two methyl group orientations at vapor/acetone interface with polarization null angle method in SFG vibrational spectroscopy

Science.gov (United States)

Chen, Hua; Gan, Wei; Wu, Bao-hua; Wu, Dan; Zhang, Zhen; Wang, Hong-fei

2005-06-01

We report a direct measurement of the orientation of the two CH 3 groups of acetone molecule at the vapor/acetone interface. The interfacial acetone molecule is found well-ordered, with one methyl group points away around 14.4° ± 1.9° and another into the bulk liquid around 102.8° ± 1.9° from the interface normal, and thus the C dbnd O group points into the bulk around 135.8° ± 1.9°. These results directly confirmed the highly ordered and even crystal like interfacial structure of the vapor/acetone interface from previous MD simulation. The general formulation and accurate determination of the orientational parameter D can be used to treat interfaces with complex molecular orientations.

DSC and curing kinetics study of epoxy grouting diluted with furfural -acetone slurry

Science.gov (United States)

Yin, H.; Sun, D. W.; Li, B.; Liu, Y. T.; Ran, Q. P.; Liu, J. P.

2016-07-01

The use of furfural-acetone slurry as active diluents of Bisphenol-A epoxy resin (DGEBA) groutings has been studied by dynamic and non-isothermal DSC for the first time. Curing kinetics study was investigated by non-isothermal differential scanning calorimetries at different heating rates. Activation enery (Ea) was calculated based on Kissinger and Ozawa Methods, and the results showed that Ea increased from 58.87 to 71.13KJ/mol after the diluents were added. The furfural-acetone epoxy matrix could cure completely at the theoretical curing temperature of 365.8K and the curing time of 139mins, which were determined by the kinetic model parameters.

Histochemical detection of GM1 ganglioside using cholera toxin-B subunit. Evaluation of critical factors optimal for in situ detection with special emphasis to acetone pre-extraction

Science.gov (United States)

Petr, T.; Šmíd, V.; Šmídová, J.; Hůlková, H.; Jirkovská, M.; Elleder, M.; Muchová, L.; Vítek, L.; Šmíd, F.

2010-01-01

A comparison of histochemical detection of GM1 ganglioside in cryostat sections using cholera toxin B-subunit after fixation with 4% formaldehyde and dry acetone gave tissue-dependent results. In the liver no pre-treatment showed detectable differences related to GM1 reaction products, while studies in the brain showed the superiority of acetone pre-extraction (followed by formaldehyde), which yielded sharper images compared with the diffuse, blurred staining pattern associated with formaldehyde. Therefore, the aim of our study was to define the optimal conditions for the GM1 detection using cholera toxin B-subunit. Ganglioside extractability with acetone, the ever neglected topic, was tested comparing anhydrous acetone with acetone containing admixture of water. TLC analysis of acetone extractable GM1 ganglioside from liver sections did not exceed 2% of the total GM1 ganglioside content using anhydrous acetone at −20°C, and 4% at room temperature. The loss increased to 30.5% using 9:1 acetone/water. Similarly, photometric analysis of lipid sialic acid, extracted from dried liver homogenates with anhydrous acetone, showed the loss of gangliosides into acetone 3.0±0.3% only. The loss from dried brain homogenate was 9.5±1.1%. Thus, anhydrous conditions (dry tissue samples and anhydrous acetone) are crucial factors for optimal in situ ganglioside detection using acetone pre-treatment. This ensures effective physical fixation, especially in tissues rich in polar lipids (precipitation, prevention of in situ diffusion), and removal of cholesterol, which can act as a hydrophobic blocking barrier. PMID:20558344

Histochemical detection of GM1 ganglioside using cholera toxin-B subunit. Evaluation of critical factors optimal for in situ detection with special emphasis to acetone pre-extraction

Directory of Open Access Journals (Sweden)

T. Petr

2010-05-01

Full Text Available A comparison of histochemical detection of GM1 ganglioside in cryostat sections using cholera toxin B-subunit after fixation with 4% formaldehyde and dry acetone gave tissue-dependent results. In the liver no pre-treatment showed detectable differences related to GM1 reaction products, while studies in the brain showed the superiority of acetone pre-extraction (followed by formaldehyde, which yielded sharper images compared with the diffuse, blurred staining pattern associated with formaldehyde. Therefore, the aim of our study was to define the optimal conditions for the GM1 detection using cholera toxin B-subunit. Ganglioside extractability with acetone, the ever neglected topic, was tested comparing anhydrous acetone with acetone containing admixture of water. TLC analysis of acetone extractable GM1 ganglioside from liver sections did not exceed 2% of the total GM1 ganglioside content using anhydrous acetone at -20°C, and 4% at room temperature. The loss increased to 30.5% using 9:1 acetone/water. Similarly, photometric analysis of lipid sialic acid, extracted from dried liver homogenates with anhydrous acetone, showed the loss of gangliosides into acetone 3.0±0.3% only. The loss from dried brain homogenate was 9.5±1.1%. Thus, anhydrous conditions (dry tissue samples and anhydrous acetone are crucial factors for optimal in situ ganglioside detection using acetone pre-treatment. This ensures effective physical fixation, especially in tissues rich in polar lipids (precipitation, prevention of in situ diffusion, and removal of cholesterol, which can act as a hydrophobic blocking barrier.

Photocatalytic degradation of acetone and butane on mesoporous titania layers

Czech Academy of Sciences Publication Activity Database

Štengl, Václav; Houšková, Vendula; Bakardjieva, Snejana; Murafa, Nataliya

2010-01-01

Roč. 34, č. 9 (2010), s. 1999-2005 ISSN 1144-0546 R&D Projects: GA ČR GA203/08/0334 Institutional research plan: CEZ:AV0Z40320502 Keywords : thin-films * gaseous acetone * oxidation * TIO2 Subject RIV: CA - Inorganic Chemistry Impact factor: 2.631, year: 2010

Breath acetone concentration; biological variability and the influence of diet

Czech Academy of Sciences Publication Activity Database

Španěl, Patrik; Dryahina, Kseniya; Rejšková, A.; Chippendale, T. W. E.; Smith, D.

2011-01-01

Roč. 32, č. 8 (2011), N23-N31 ISSN 0967-3334 R&D Projects: GA ČR GP203/09/P172 Institutional research plan: CEZ:AV0Z40400503 Keywords : acetone * breath * ketogenic diet Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.677, year: 2011

Methyl and isopropyl N-methylanthranilates attenuate diclofenac- and ethanol-induced gastric lesions in rats.

Science.gov (United States)

Radulović, Niko S; Jovanović, Ivan; Ilić, Ivan R; Randjelović, Pavle J; Stojanović, Nikola M; Miltojević, Ana B

2013-11-19

Two natural alkaloids, methyl (M) and isopropyl (I) N-methylanthranilates, with recently demonstrated significant pharmacological activities, were assayed for their possible overall effect on intact gastric mucosa and their protective properties towards the onset of gastric lesions induced by diclofenac (a non-steroidal anti-inflammatory drug, NSAID) or ethanol. The influence of I and M on gastric mucosa integrity was assessed by oral administration in doses of 200mg/kg. The gastroprotective action of I and M in doses of 50, 100 and 200mg/kg was analyzed in the diclofenac and ethanol-induced gastric lesion models in rats. After the treatment, the stomachs of the animals were analyzed (captured by a digital camera). Ulcer scoring, morphometric and histopathological analyses of the stomachs were done. The oral application of these compounds on their own, even in quite high doses (200mg/kg) did not induce gastric lesions. Both alkaloids exerted a very strong antiulcer activity, even in low doses (50mg/kg), by decreasing the number of lesions caused by the application of either diclofenac or ethanol, eliminating them completely or reducing them to a form of mucosal hyperemia. Their possible mechanism of action was discussed and due to their many positive properties including anxiolytic, antidepressant, antinociceptive, anti-inflammatory and gastroprotective activities, as well as a cheap and simple synthetic route for their preparation, methyl and isopropyl N-methylanthranilates, both alike, might represent a cost effective alternative sought for in the treatment of peptic ulcers and/or new safer NSAIDs for pain management. © 2013.

Toxicity study of di(2-ethylhexyl)phthalate (DEHP) in combination with acetone in rats

DEFF Research Database (Denmark)

Dalgaard, M.; Østergaard, G.; Lam, Henrik Rye

2000-01-01

In two separate studies with exposure duration 9 weeks or 4 weeks, male Wistar rats were dosed with di(2-ethylhexyl)phthalate (DEHP) by gavage and exposed to drinking water with or without acetone (0.5% wt/v in the 9-week study, 1.0% wt/v in the 4-week study). In the 9-week study the doses of DEHP...... were 0, 125, 250, 500 or 1000 mg/kg b.wt. In the 4-week study the doses of DEHP were increased to 1000, 5000 and 10,000 mg/kg b.wt. In the 9-week study, the relative liver weight was increased in the rats exposed to 500 and 1000 mg/kg b.wt. No interaction of DEHP and acetone was observed in any...... of the measured parameters. In the 4-week study DEHP, at the highest dose level, resulted in severe general toxicity. The group exposed to DEHP in combination with acetone was more affected. Male fertility was decreased. Body weight was decreased, and the relative weight of the liver, kidney, heart, brain...

Poly(N-isopropyl acrylamide)-block-poly(n-butyl acrylate) thermoresponsive amphiphilic copolymers: synthesis, characterization and self-assembly behavior in aqueous solutions

Czech Academy of Sciences Publication Activity Database

Škvarla, J.; Zedník, J.; Šlouf, Miroslav; Pispas, S.; Štěpánek, M.

2014-01-01

Roč. 61, December (2014), s. 124-132 ISSN 0014-3057 R&D Projects: GA TA ČR TE01020118 Institutional support: RVO:61389013 Keywords : thermoresponsive block copolymers * poly(N-isopropyl acrylamide) * light scattering Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.005, year: 2014

Comparison of yield, composition, and antioxidant activity of turmeric (Curcuma longa L.) extracts obtained using various techniques.

Science.gov (United States)

Braga, Mara E M; Leal, Patrícia F; Carvalho, João E; Meireles, M Angela A

2003-10-22

Turmeric extracts were obtained from two lots of raw material (M and S) using various techniques: hydrodistillation, low pressure solvent extraction, Soxhlet, and supercritical extraction using carbon dioxide and cosolvents. The solvents and cosolvents tested were ethanol, isopropyl alcohol, and their mixture in equal proportions. The composition of the extracts was determined by gas chromatography-flame ionization detection (GC-FID) and UV. The largest yield (27%, weight) was obtained in the Soxhlet extraction (turmeric (S), ethanol = 1:100); the lowest yield was detected in the hydrodistillation process (2.1%). For the supercritical extraction, the best cosolvent was a mixture of ethanol and isopropyl alcohol. Sixty percent of the light fraction of the extracts consisted of ar-turmerone, (Z)-gamma-atlantone, and (E)-gamma-atlantone, except for the Soxhlet extracts (1:100, ethanol), for which only ar-turmeronol and (Z)-alpha-atlantone were detected. The maximum amount of curcuminoids (8.43%) was obtained using Soxhlet extraction (ethanol/isopropyl alcohol). The Soxhlet and low pressure extract exhibited the strongest antioxidant activities.

α-chymotrypsin in water-acetone and water-dimethyl sulfoxide mixtures: Effect of preferential solvation and hydration.

Science.gov (United States)

Sirotkin, Vladimir A; Kuchierskaya, Alexandra A

2017-10-01

We investigated water/organic solvent sorption and residual enzyme activity to simultaneously monitor preferential solvation/hydration of protein macromolecules in the entire range of water content at 25°C. We applied this approach to estimate protein destabilization/stabilization due to the preferential interactions of bovine pancreatic α-chymotrypsin with water-acetone (moderate-strength H-bond acceptor) and water-DMSO (strong H-bond acceptor) mixtures. There are three concentration regimes for the dried α-chymotrypsin. α-Chymotrypsin is preferentially hydrated at high water content. The residual enzyme activity values are close to 100%. At intermediate water content, the dehydrated α-chymotrypsin has a higher affinity for acetone/DMSO than for water. Residual enzyme activity is minimal in this concentration range. The acetone/DMSO molecules are preferentially excluded from the protein surface at the lowest water content, resulting in preferential hydration. The residual catalytic activity in the water-poor acetone is ∼80%, compared with that observed after incubation in pure water. This effect is very small for the water-poor DMSO. Two different schemes are operative for the hydrated enzyme. At high and intermediate water content, α-chymotrypsin exhibits preferential hydration. However, at intermediate water content, in contrast to the dried enzyme, the initially hydrated α-chymotrypsin possesses increased preferential hydration parameters. At low water content, no residual enzyme activity was observed. Preferential binding of DMSO/acetone to α-chymotrypsin was detected. Our data clearly demonstrate that the hydrogen bond accepting ability of organic solvents and the protein hydration level constitute key factors in determining the stability of protein-water-organic solvent systems. © 2017 Wiley Periodicals, Inc.

Brain SPECT with 123I-isopropyl amphetamine in epilepsy

International Nuclear Information System (INIS)

Biersack, H.J.; Reske, S.N.; Rasche, A.; Reichmann, K.; Winkler, C.

1983-01-01

Ten patients were studied with N-isopropyl I-123 p-iodoamphetamine. Single photon emission computed tomography (SPECT) was carried out by hand of a rotating gamma camera system (Gammatome T9000/CGR, high resolution collimator). During 1 rotation (360 0 ) 64 frames (4k matrix) were acquired within 20 min 1 hour after injection of 6.5 mCi I-123 labeled amphetamine. The content of I-124 was less than 2%. After reconstruction of transverse slices coronar and sagittal reconstructions were rapidly performed using an array processor. Nine patients suffered from epilepsy and one from severe migraine. Excellent differentiation between gray and white matter of the cerebral cortex and the basal ganglia was evident in all of the cases. In 2 out of 3 patients with epilepsy and negative CT results SPECT revealed circumscribed areas with increased amphetamine uptake in accordance with the EEG findings. In 4 out of 6 cases with positive CT findings SPECT lesions with diminished amphetamine uptake could be established. One patient with severe migraine showed focal increased amphetamine uptake in accordance with the respective clinical results. (orig.)

Multi-shelled ZnCo2O4 yolk-shell spheres for high-performance acetone gas sensor

Science.gov (United States)

Xiong, Ya; Zhu, Zongye; Ding, Degong; Lu, Wenbo; Xue, Qingzhong

2018-06-01

In the present study, multi-shelled ZnCo2O4 yolk-shell spheres have been successfully prepared by using carbonaceous microspheres as templates. It is found that the multi-shelled ZnCo2O4 yolk-shell spheres based sensor shows optimal sensing performances (response value of 38.2, response/recovery time of 19 s/71 s) toward 500 ppm acetone at 200 °C. In addition, this sensor exhibits a low detection limit of 0.5 ppm acetone (response value of 1.36) and a good selectivity toward hydrogen, methane, ethanol, ammonia and carbon dioxide. Furthermore, it is demonstrated that acetone gas response of multi-shelled ZnCo2O4 yolk-shell spheres is significantly better than that of ZnCo2O4 nanotubes and ZnCo2O4 nanosheets. High acetone response of the multi-shelled ZnCo2O4 yolk-shell spheres is attributed to the enhanced gas accessibility of the multi-shell morphology caused by the small crystalline size and high specific surface area while the short response/recovery time is mainly related to the rapid gas diffusion determined by the highly porous structure. Our work puts forward an exciting opportunity in designing various yolk-shelled structures for multipurpose applications.

VOC amounts in ambient areas of a high-technology science park in Taiwan: their reciprocal correlations and impact on inhabitants.

Science.gov (United States)

Liu, Hsin-Wang; Wu, Bei-Zen; Nian, Hung-Chi; Chen, Hsing-Jung; Lo, Jiunn-Guang; Chiu, Kong-Hwa

2012-02-01

This study presents bihourly, seasonal, and yearly concentration changes in volatile organic compounds (VOCs) in the inlet and effluent water of the wastewater treatment plant (WWTP) of a high-technology science park (HTIP) in Taiwan, with the VOC amounts at different sites correlated geologically. This research adopted a combination of two systems, solid-phase microextraction with a gas chromatography/flame ionization detector and an assembly of purge and trap coupled with gas chromatography/mass spectrometry, to monitor polar and nonpolar VOCs in wastewater. This paper investigated the total VOCs, acetone, isopropyl alcohol (IPA), and dimethylsulfide (DMS) concentrations in real water samples collected in the ambient area of the HTIP. The major contents of VOCs measured in the effluent of the WWTP in the HTIP and the surrounding river region were DMS (14-176 ppb), acetone (5-95 ppb), and IPA (15-316 ppb). In comparison with the total VOCs in the inlet wastewater of the WWTP, no corresponding relationship for total VOC concentration in the wastewater was observed between the inlet water and effluent water of the WWTP. The peak VOC concentrations appeared in the third season, and the correlation of different VOC amounts reflects the production situation of the factories. In addition, VOC concentrations at different sites indicate that the Ke-Ya River is seemingly an effective channel for transporting wastewater to its final destination. The data are good indications for the management of environmental pollution near the HTIP.

The use of technetium-99m-di-isopropyl-iminodiacetic acid imaging in the demonstration of a biliary-bronchial fistula

International Nuclear Information System (INIS)

Savitch, I.; Esser, J.D.; Levin, J.; Krige, L.P.; Kew, M.C.

1984-01-01

A case is described in which technetium-99m-di-isopropyl-iminodiacetic acid imaging was used to trace the passage of bile from its site of leakage into an amoebic liver abscess, through a fistulous tract connecting the liver abscess with an abscess in the right lower lobe of the lung, and into the upper respiratory tract

Thermodynamics and economic feasibility of acetone production from syngas using the thermophilic production host Moorella thermoacetica

DEFF Research Database (Denmark)

Redl, Stephanie Maria Anna; Sukumara, Sumesh; Ploeger, Tom

2017-01-01

-gas via condensation. Results: In this study we analyzed the production of acetone from syngas with the hypothetical production host derived from Moorella thermoacetica in a bubble column reactor at 60 degrees C with respect to thermodynamic and economic feasibility. We determined the cost of syngas...... production from basic oxygen furnace (BOF) process gas, from natural gas, and from corn stover and identified BOF gas as an economically interesting source for syngas. Taking gasliquid mass transfer limitations into account, we applied a thermodynamics approach to derive the CO to acetone conversion rate...... under the process conditions. We estimated variable costs of production of 389 $/t acetone for a representative production scenario from BOF gas with costs for syngas as the main contributor. In comparison, the variable costs of production from natural gas-and corn stover-derived syngas were determined...

Analysis of O-Glycopeptides by Acetone Enrichment and Capillary Electrophoresis-Mass Spectrometry.

Science.gov (United States)

Mancera-Arteu, Montserrat; Giménez, Estela; Benavente, Fernando; Barbosa, José; Sanz-Nebot, Victòria

2017-11-03

Acetone precipitation was evaluated as a rapid, simple, low-cost, and efficient method for the selective purification of O-glycopeptides from enzymatic digests of glycoproteins. Ovalbumin (OVA), human and bovine α 1 -acid glycoprotein (hAGP and bAGP), human apolipoprotein C-III (APO-C3), and recombinant human erythropoietin (rhEPO) were used to obtain enzymatic digests with a broad and varied set of peptides, N-glycopeptides, and O-glycopeptides. After digestion and before capillary electrophoresis mass spectrometry (CE-MS) analysis, the amount of ice-cold acetone added to the digests was optimized to maximize recoveries of O-glycopeptides. Furthermore, the different behavior of peptides, N- and O-glycopeptides was explained by studying with multivariate data analysis methods the influence of several physicochemical parameters and properties related to their composition and structure. Principal component analysis (PCA) and, afterward, partial least-squares discriminant analysis (PLS-DA) were used to identify the most significant variables and their importance to differentiate between peptides, N-glycopeptides and O-glycopeptides, or within these classes. This information was useful to understand precipitation of these compounds after addition of acetone and for the selection of the optimal conditions for purification of specific O-glycopeptide biomarkers. Special attention was paid to O 126 -glycopeptide glycoforms of rhEPO because of their applicability in biopharmaceutical quality control and doping analysis.

Butanol-acetone fermentation. Bibliographic synthesis and current trends

Energy Technology Data Exchange (ETDEWEB)

Marchal, R. (Institut Francais du Petrole, Rueil-Malmaison (France))

This article gives a synthesis of what is known about butyl-acetone fermentation from both the microbiological and technological standpoints. Different aspects of the metabolism of the microorganism used and of how it is regulated are considered. The performances of fermentation on traditional substrates (cornmeal or molasses) are compared with those recently obtained using Jerusalem artichokes at Institut Francais du Petrole as part of a new project on this fermentation for the purpose of producing substitute fuel.

In-cloud multiphase behaviour of acetone in the troposphere: gas uptake, Henry's law equilibrium and aqueous phase photooxidation.

Science.gov (United States)

Poulain, Laurent; Katrib, Yasmine; Isikli, Estelle; Liu, Yao; Wortham, Henri; Mirabel, Philippe; Le Calvé, Stéphane; Monod, Anne

2010-09-01

Acetone is ubiquitous in the troposphere. Several papers have focused in the past on its gas phase reactivity and its impact on tropospheric chemistry. However, acetone is also present in atmospheric water droplets where its behaviour is still relatively unknown. In this work, we present its gas/aqueous phase transfer and its aqueous phase photooxidation. The uptake coefficient of acetone on water droplets was measured between 268 and 281K (γ=0.7 x 10(-2)-1.4 x 10(-2)), using the droplet train technique coupled to a mass spectrometer. The mass accommodation coefficient α (derived from γ) was found in the range (1.0-3.0±0.25) x 10(-2). Henry's law constant of acetone was directly measured between 283 and 298K using a dynamic equilibrium system (H((298K))=(29±5)Matm(-1)), with the Van't Hoff expression lnH(T)=(5100±1100)/T-(13.4±3.9). A recommended value of H was suggested according to comparison with literature. The OH-oxidation of acetone in the aqueous phase was carried out at 298K, under two different pH conditions: at pH=2, and under unbuffered conditions. In both cases, the formation of methylglyoxal, formaldehyde, hydroxyacetone, acetic acid/acetate and formic acid/formate was observed. The formation of small amounts of four hydroperoxides was also detected, and one of them was identified as peroxyacetic acid. A drastic effect of pH was observed on the yields of formaldehyde, one hydroperoxide, and, (to a lesser extent) acetic acid/acetate. Based on the experimental observations, a chemical mechanism of OH-oxidation of acetone in the aqueous phase was proposed and discussed. Atmospheric implications of these findings were finally discussed. Copyright © 2010 Elsevier Ltd. All rights reserved.

Temperature Programmed Desorption of Quench-condensed Krypton and Acetone in Air; Selective Concentration of Ultra-trace Gas Components.

Science.gov (United States)

Suzuki, Taku T; Sakaguchi, Isao

2016-01-01

Selective concentration of ultra-trace components in air-like gases has an important application in analyzing volatile organic compounds in the gas. In the present study, we examined quench-condensation of the sample gas on a ZnO substrate below 50 K followed by temperature programmed desorption (TPD) (low temperature TPD) as a selective gas concentration technique. We studied two specific gases in the normal air; krypton as an inert gas and acetone as a reactive gas. We evaluated the relationship between the operating condition of low temperature TPD and the lowest detection limit. In the case of krypton, we observed the selective concentration by exposing at 6 K followed by thermal desorption at about 60 K. On the other hand, no selectivity appeared for acetone although trace acetone was successfully concentrated. This is likely due to the solvent effect by a major component in the air, which is suggested to be water. We suggest that pre-condensation to remove the water component may improve the selectivity in the trace acetone analysis by low temperature TPD.

Regulation of N-nitrosodimethylamine demethylase in rat liver and kidney.

Science.gov (United States)

Hong, J Y; Pan, J M; Dong, Z G; Ning, S M; Yang, C S

1987-11-15

In previous work, the low Km form of N-nitrosodimethylamine (NDMA) demethylase has been demonstrated to be due to a specific form of cytochrome P-450 (designated as P-450ac) and to be the enzyme required for the metabolic activation of NDMA. The present work deals with the regulation of P-450ac in rat liver during development as well as the mechanism of induction of P-450ac in rat liver and kidney by inducers. NDMA demethylase activity was almost undetectable in the liver of newborn rats, increased after day 4, and remained elevated throughout the first 17 days of the neonatal period. The enhancement of NDMA demethylase activity during development was accompanied by corresponding increases of P-450ac content and P-450ac mRNA levels as determined by Western and slot blot analyses, respectively. No sex differences with respect to this enzyme were observed in the developing rats. Acetone treatment on late-term pregnant rats for 2 days resulted in transplacental inductions of P-450ac and P-450ac mRNA in the newborn rats. Pretreatment of young male rats and adult female rats with acetone or isopropyl alcohol caused increases of NDMA demethylase activity and P-450ac content in the liver but no significant change in the P-450ac mRNA level. These facts suggest the possible existence of a posttranscription regulatory mechanism under these induction conditions. The presence of P-450ac in rat kidney was demonstrated by Western and Northern blot analyses. The renal form of P-450ac seemed to be regulated in a fashion similar to the hepatic P-450ac regarding its response to inducing factors such as fasting and acetone treatment.

Effects of acetone-soaking treatment on the performance of polymer solar cells based on P3HT/PCBM bulk heterojunction

International Nuclear Information System (INIS)

Liu Yu-Xuan; Lü Long-Feng; Ning Yu; Lu Yun-Zhang; Lu Qi-Peng; Zhang Chun-Mei; Fang Yi; Hu Yu-Feng; Lou Zhi-Dong; Teng Feng; Hou Yan-Bing; Tang Ai-Wei

2014-01-01

The improvement of the acetone-soaking treatment to the performance of polymer solar cells based on the P3HT/PCBM bulk heterojunction is reported. Undergoing acetone-soaking, the PCBM does not distribute uniformly in the vertical direction, a PCBM enrichment layer forms on the top of the active layer, which is beneficial to the collection of the carriers and blocking the inverting diffusion carriers. X-ray photoelectron spectroscopy (XPS) analysis reveals that the PCBM weight ratio on the top of the active layer increases by 20% after the acetone-soaking treatment. Due to the nonuniform distribution of PCBM, the short-circuit current density, the open-circuit voltage, and the fill factor are enhanced significantly. Finally, the power conversion efficiency of the acetone-soaking device increases by 31% compared with the control device. (interdisciplinary physics and related areas of science and technology)

Lithium isotope effects in cation exchange chromatography of lithium lactate in water-dimethyl sulfoxide and water-acetone mixed solvent media

International Nuclear Information System (INIS)

Oi, Takao; Kondoh, Akiko; Ohno, Etsuko; Hosoe, Morikazu

1993-01-01

Lithium isotope separation by ion exchange displacement chromatography of lithium lactate in water-dimethyl sulfoxide (DMSO) and water-acetone mixed solvent media at 25 C was explored. In both the water-DMSO and water-acetone system, the single stage isotope separation factor (S) was a convex function of the mixing ratio of the solvents in the external solution phase; S had its maximum value of 1.00254 at water: DMSO=25:75 v/v and 1.00182 at water: acetone=75:25 v/v. Strong correlations of S with solvent partitions between the solution and the exchanger phases were found in both systems, which was qualitatively explainable by considering the lithium isotope distributions between the two phases based on the fundamental lithium isotope effects and the relative affinities of water, DMSO and acetone towards the lithium ion. (orig.)

KINETIC STUDY OF SELECTIVE GAS-PHASE OXIDATION OF ISOPROPANOL TO ACETONE USING MONOCLINIC ZRO2 AS A CATALYST

Directory of Open Access Journals (Sweden)

Mohammad Sadiq

2015-08-01

Full Text Available Zirconia was prepared by a precipitation method and calcined at 723 K, 1023 K, and 1253 K in order to obtain monoclinic zirconia. The prepared zirconia was characterized by XRD, SEM, EDX, surface area and pore size analyzer, and particle size analyzer. Monoclinic ZrO2 as a catalyst was used for the gas-phase oxidation of isopropanol to acetone in a Pyrex-glass-flow-type reactor with a temperature range of 443 K - 473 K. It was found that monoclinic ZrO2 shows remarkable catalytic activity (68% and selectivity (100% for the oxidation of isopropanol to acetone. This kinetic study reveals that the oxidation of isopropanol to acetone follows the L-H mechanism.

Fermentation of molasses-flour mashes by acetone-butanol bacteria

Energy Technology Data Exchange (ETDEWEB)

Chekasina, E V

1962-01-01

With Clostridium acetobutylicum used in a continuous fermentation, where the mash passes through 5 to 12 fermenters, sufficient conversion of starch to mono- and disaccharides will occur; the number of fermenters were chosen and mash changed so that fresh mash remains for 34 hours in the cycle. After a 29 hour fermentation average yields were: acetone 4.5, ethanol 3.0, butanol 7.5%.

Reactions of α-phosphorylated carbonyl compounds with amino alcohols

International Nuclear Information System (INIS)

Moskva, V.V.; Sitdikova, T.Sh.; Zykova, T.V.; Alparova, M.V.; Shagvaleev, F.Sh.

1986-01-01

2-Aminoethanol reacts with carbonyl compounds with the formation, depending on the structure of the latter, either of a mixture of azomethines and oxazolidines, or of only azomethines. In the development of investigations on the reactivity of α-phosphorylated carbonyl compounds the authors studied the reactions of a number of amino alcohols with phosphorylated acetaldehyde and acetone. In both cases they observed the formation of compounds of enamine structure, oxazolidines and azomethines were not observed. By means of NMR spectroscopy they established clearly the formation of the E-isomeric products. The 1 H, 31 P, and 13 C NMR spectra were recorded on a WP-80 spectrometer. Chemical shifts of protons and 13 C nuclei are given relative to TMS, and phosphorus nuclei relative to orthophosphoric acid

Development of Lecithin Nanoemulsion Based Organogels for Permeation Enhancement of Metoprolol through Rat Skin

Directory of Open Access Journals (Sweden)

J. Varshosaz

2013-01-01

Full Text Available Background. Drugs with low oral bioavailability due to the first pass metabolism are good candidates for transdermal delivery. Objectives. The aim of this work was preparation of transdermal nanoemulsion of metoprolol which has high first pass metabolism. Methods. Three commercially available types of lecithin (200, 100p, and 170, three short chain alcohol (n-butanol, isopropyl alcohol, and n-propanol, and isopropyl myristate (IPM were used as surfactant, cosurfactant, and oil phase, respectively. The aqueous phase was composed of metoprolol tartrate. Nanoemulsions with different surfactant/cosurfactant weight ratio, various amounts of drug, and different types of alcohol were prepared, and their phase diagrams were studied. Drug release, permeability, and diffusion coefficient of the drug were studied using hairless rat skin. Results. A significant increase in drug solution rate was observed with increasing the metoprolol content in the nanoemulsions, while it decreased when lecithin concentration increased from 40% to 60%. Increasing the water content resulted in a significant increase in metoprolol release. N-butanol enhanced the drug flux from nanoemulsions more than n-propanol and isopropyl alcohol. The o/w nanoemulsions of metoprolol showed high flux and permeability through the skin. Conclusion. Both w/o and o/w nanoemulsions of metoprolol could enhance permeation and diffusion of metoprolol through rat skin.

Interaction of silico-12-molybdic acid with acetone

International Nuclear Information System (INIS)

Chuvaev, V.F.; Pinchuk, I.N.; Gubin, V.V.

1984-01-01

Methods of thermal analysis, mass-spectrometry, IR, PMR, ESR spectroscopy are used to investigate interaction processes of silico-12-molybdic acid H 4 SiMo 12 O 40 with acetone. Reactions in solution and with participation of solid heteropolyacid are studied. Organic products of catalytic and oxidation-reduction reactions are identified. The effect of conditions on the formation of different condensation and oxidation products and the sequence of appropriate reactions is discussed. Transformations of silico-12-molybolic acid are considered

Methanogenic degradation of acetone by an enrichment culture

OpenAIRE

Platen, Harald; Schink, Bernhard

1987-01-01

An anaerobic enrichment culture degraded 1 mol of acetone to 2 tool of methane and 1 tool of carbon dioxide. Two microorganisms were involved in this process, a filament-forming rod similar to Methanothrix sp. and an unknown rod with round to slightly pointed ends. Both organisms formed aggregates up to 300 gm in diameter. No fluorescing bacteria were observed indicating that hydrogen or formate-utilizing methanogens are not involved in this process. Acetate was utilized in this culture by th...

Cross-Selectivity Enhancement of Poly(vinylidene fluoride-hexafluoropropylene-Based Sensor Arrays for Detecting Acetone and Ethanol

Directory of Open Access Journals (Sweden)

Ali Daneshkhah

2017-03-01

Full Text Available Two methods for cross-selectivity enhancement of porous poly(vinylidene fluoride-hexafluoropropylene (PVDF-HFP/carbon black (CB composite-based resistive sensors are provided. The sensors are tested with acetone and ethanol in the presence of humid air. Cross-selectivity is enhanced using two different methods to modify the basic response of the PVDF-HFP/CB sensing platform. In method I, the adsorption properties of PVDF-HFP/CB are altered by adding a polyethylene oxide (PEO layer or by treating with infrared (IR. In method II, the effects of the interaction of acetone and ethanol are enhanced by adding diethylene carbonate (DEC or PEO dispersed in DEC (PEO/DEC to the film. The results suggest the approaches used in method I alter the composite ability to adsorb acetone and ethanol, while in method II, they alter the transduction characteristics of the composite. Using these approaches, sensor relative response to acetone was increased by 89% compared with the PVDF-HFP/CB untreated film, whereas sensor relative response to ethanol could be decreased by 57% or increased by 197%. Not only do these results demonstrate facile methods for increasing sensitivity of PVDF-HFP/CB film, used in parallel they demonstrate a roadmap for enhancing system cross-selectivity that can be applied to separate units on an array. Fabrication methods, experimental procedures and results are presented and discussed.

Acetone in theGlobal Troposphere: Its Possible Role as a Global Source of PAN

Science.gov (United States)

Singh, H. B.; Kanakidou, M.

1994-01-01

Oxygenated hydrocarbons are thought to be important components of the atmosphere but, with the exception of formaldehyde, very little about their distribution and fate is known. Aircraft measurements of acetone (CH3COCH3), PAN (CH3CO3NO2) and other organic species (e. g. acetaldehyde, methanol and ethanol) have been performed over the Pacific, the southern Atlantic, and the subarctic atmospheres. Sampled areas extended from 0 to 12 km altitude over latitudes of 70 deg N to 40 deg S. All measurements are based on real time in-situ analysis of cryogenically preconcentrated air samples. Substantial concentrations of these oxygenated species (10-2000 ppt) have been observed at all altitudes and geographical locations in the troposphere. Important sources include, emissions from biomass burning, plant and vegetation, secondary oxidation of primary non-methane hydrocarbons, and man-made emissions. Direct measurements within smoke plumes have been used to estimate the biomass burning source. Photochemistry studies are used to suggest that acetone could provide a major source of peroxyacetyl radicals in the atmosphere and play an important role in sequestering reactive nitrogen. Model calculations show that acetone photolysis contributes significantly to PAN formation in the middle and upper troposphere.

Studies on the in vitro time kill assessment of crude acetone and ...

African Journals Online (AJOL)

STORAGESEVER

2008-10-20

Oct 20, 2008 ... infection even after treating such wounds with H. pedunculatum leaf. Perhaps .... acetone extract was evaporated to dryness under reduced pressure at 40oC ... ml of Mueller Hinton broth and recovery medium containing 3%.

Comparison of formol-acetone concentration method with that of the ...

African Journals Online (AJOL)

Bernt Lindtjorn

which consists of ether as a fat solvent for detecting out parasites from intestinal debris and thus increases the positivity rates, is believed to be superior over the other ... and petrol can be a better substitute (5, 6, 7). However, among these solvents, acetone has been rated as “safe” in comparison to the ether effect on health ...

Evaluation of the Acetone and Aqueous Extracts of Mature Stem Bark of Sclerocarya birrea for Antioxidant and Antimicrobial Properties

Directory of Open Access Journals (Sweden)

Nicoline F. Tanih

2012-01-01

Full Text Available We assayed the antimicrobial activity of acetone and aqueous extracts of the stem bark of Sclerocarya birrea on some selected bacteria and fungi species including; Streptococcus pyogenes, Plesiomonas shigelloides, Aeromonas hydrophila, Salmonella typhimurium, Cryptococcus neoformans, Candida glabrata, Trichosporon mucoides, and Candida krusei using both agar well diffusion and minimum inhibitory concentration (MIC assays. Based on the levels of activity, the acetone extract was examined for total polyphenolic content, radical scavenging and antioxidant activities. Total phenols of the extract were determined spectrophotometrically. The antioxidant activity was determined by the DPPH, ABTS and reducing power. All the bacteria and fungi species were susceptible to the plant extracts. The acetone extract was the most active for the bacterial species with MIC (0.156–0.625 mg/mL while the aqueous extract was the most active for the fungi species with MIC (0.3125–1.25 mg/mL. The polyphenolic compounds were found as 27.2 mg/g tannic acid equivalent, 25.2 mg/g quercetin equivalent, 9.1 mg/g quercetin equivalent for phenols, flavonoid and flavonols respectively. The acetone extract exhibited a remarkable ability to scavenge radicals, strong reducing ability and a potential source of natural antioxidants. Both the acetone and aqueous extracts of S. birrea may provide a target for drug discovery.

Biological activities of Umbilicaria crustulosa (Ach.) frey acetone extract

OpenAIRE

Zlatanović Ivana; Stanković Miroslava; Stankov-Jovanović Vesna; Mitić Violeta; Zrnzević Ivana; Đorđević Aleksandra; Stojanović Gordana

2017-01-01

This paper reports for the first time the effect of an acetone extract of Umbilicaria crustulosa on the micronucleus distribution of human lymphocytes, and on the cholinesterase activity and antioxidant activity by the cupric ion reducing antioxidant capacity (CUPRAC) method. Additionally, the total phenolic compounds (TPC) and the antioxidant properties were estimated via DPPH, ABTS and TRP assays. Moreover, the antibacterial activity against two Gram-positive and three Gram-negative bacteri...

The Effect of Acetone Amount Ratio as Co-Solvent to Methanol in Transesterification Reaction of Waste Cooking Oil

Science.gov (United States)

Julianto, T. S.; Nurlestari, R.

2018-04-01

The production of biodiesel from waste cooking oil by transesterification reaction using acetone as co-solvent has been carried out. This research studied the optimal amount ratio of acetone as co-solvent to methanol in the transesterification process using homogeneous alkaline catalyst KOH 1% (w/w) of waste cooking oil at room temperature for 15 minutes of reaction time. Mole ratio of waste cooking oil to methanol is 1:12. Acetone was added as co-solvent in varied amount ratio to methanol are 1:4, 1:2, and 1:1, respectively. The results of fatty acid methyl esters (FAME) were analysed using GC-MS instrument. The results showed that the optimal ratio is 1:4 with 99.93% of FAME yield.

Pathophysiologic study of chronic infarcts with I-123 isopropyl iodo-amphetamine (IMP)

DEFF Research Database (Denmark)

Raynaud, C; Rancurel, G; Samson, Y

1987-01-01

Seventeen chronic cerebral infarcts were investigated by a highly sensitive, dedicated brain single photon emission computerized tomography system using 123I-isopropyl iodoamphetamine (IMP) and 133Xe. IMP uptake was measured 10 minutes, 2 hours, and 5 hours after injection, and regional cerebral...... blood flow was measured with 133Xe. In 4 cases a positron emission tomography system was used to measure the rCBF and the regional metabolic rate of oxygen with C15O2 and 15O2. The results obtained allowed us to identify 2 abnormal zones. One, the "central area," was characterized by a severe decrease...... ischemic neuronal loss. The results stress the important role played by the peripheral area, which may be useful in establishing the prognosis and evaluating the efficacy of therapy in individual stroke cases....

Structural effect of ferrocenecarboxymethylated polymers on their electrical behavior under the exposure to methanol and acetone vapors

International Nuclear Information System (INIS)

Hachawee, Kosin; Lerdwijitjarud, Wanchai; Sittattrakul, Amnard; Sirivat, Anuvat

2008-01-01

Functionalized ferrocenecarboxymethylated polymers, i.e. poly(vinylbenzyl ferrocenecarboxymethylate) (PVBFCC), poly(vinylbenzyl ferrocenecarboxymethylate-co-ethoxyethylmethacrylate) with the mole ratio between vinylbenzyl ferrocenecarboxymethylate and ethoxyethylmethacrylate of 75:25 (Co-PVBFCC 75/25) and 50:50 (Co-PVBFCC 50/50), and ferrocenecarboxymethylated polysulfone (BPSFCC) were investigated for their electrical behavior under the vapors of methanol and acetone and nitrogen gas. Electrical conductivity responses of the four ferrocenecarboxymethylated polymers in the presence of lithium perchlorate were measured when they were exposed to nitrogen gas, and methanol and acetone vapors. Main factors that affect the electrical conductivity and sensitivity of these electroactive ferrocene polymers originate from the polymer structure and the type of the passing gas or vapor. Ferrocenecarboxymethylated polymers with higher degrees of substitution of ferrocene units possess good electrical conductivity under the atmosphere of mixed N 2 /methanol vapor, while ferrocenecarboxymethylated polymers with more flexible chain and/or larger free volumes give higher electrical conductivity under the atmosphere of mixed N 2 /acetone vapor. The gas or vapor molecule with higher polarity and smaller size enhances the electrical conductivity of the ferrocene polymers. Our results clearly indicate that the synthesized ferrocenecarboxymethylated polymers have potential to be used as methanol or acetone sensor materials

Synthesis of 1-isopropyl-3-acyl-5-methyl-benzimidazolone Derivatives and Their Antimicrobial Activity

Directory of Open Access Journals (Sweden)

Shaopeng Wei

2013-03-01

Full Text Available A series of N-acylated analogues of 1-isopropyl-3-acyl-5-methyl-benzimidazolone were synthesized. Bioassay results indicated that analogues 5-07 and 5-19 exhibited the most potency against Bacillus cereus, Bacillus subtilis, Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa. Analogues 5-02, 5-07, 5-12, 5-15, 5-19, 5-20 and 5-25 could effectively inhibit the spore germination of Botrytis cinerea. The relationship between structure and their antimicrobial activity (SAR has also been discussed according to aliphatic acids and aromatic acids derivatives, respectively. This implied that the N-acylated derivatives of 5-methyl-benzimidazolone might be potential antimicrobial agents.

Salting Effects as an Illustration of the Relative Strength of Intermolecular Forces

Science.gov (United States)

Person, Eric C.; Golden, Donnie R.; Royce, Brenda R.

2010-01-01

This quick and inexpensive demonstration of the salting of an alcohol out of an aqueous solution illustrates the impact of intermolecular forces on solubility using materials familiar to many students. Ammonium sulfate (fertilizer) is added to an aqueous 35% solution of isopropyl alcohol (rubbing alcohol and water) containing food coloring as a…

Effect of Gold Dispersion on the Photocatalytic Activity of Mesoporous Titania for the Vapor-Phase Oxidation of Acetone

Directory of Open Access Journals (Sweden)

S. V. Awate

2008-01-01

Full Text Available Mesostructured titanium dioxide photocatalyst, having uniform crystallite size (6–12 nm and average pore diameter of ∼4.2 nm, was synthesized by using a low-temperature nonsurfactant hydrothermal route, employing tartaric acid as a templating agent. Gold additions from 0.5 to 2 wt% were incorporated, either during the hydrothermal process or by postsynthesis wet impregnation. Compared to the impregnation-prepared samples, the samples synthesized hydrothermally contained smaller-size (≤1 nm gold clusters occluded in the pores of the host matrix. Whereas CO2 and H2O were the main reaction products in UV-assisted vapor-phase oxidation of acetone using these catalysts, C2H6 and HCO2CH3 were also produced for higher acetone concentrations in air. The conversion of acetone was found to increase with decrease in the size of both TiO2 and gold particles. In situ IR spectroscopy revealed that titania and gold particles serve as independent adsorption and reaction sites for acetone and oxygen molecules. Acetone molecules adsorb exclusively at TiO2 surface, giving rise to a strongly adsorbed (condensed state as well as to the formation of formate- and methyl formate-type surface species. Hydroxyl groups at titania surface participate directly in these adsorption steps. Nanosize gold particles, on the other hand, were primarily responsible for the adsorption and activation of oxygen molecules. Mechanistic aspects of the photochemical processes are discussed on the basis of these observations.

Comparison of voiding function and nociceptive behavior in two rat models of cystitis induced by cyclophosphamide or acetone

Science.gov (United States)

Saitoh, Chikashi; Yokoyama, Hitoshi; Chancellor, Michael B.; de Groat, William C.; Yoshimura, Naoki

2009-01-01

Aims Nociceptive behavior and its relationship with bladder dysfunction were investigated in two cystitis models, which were induced by intraperitoneal (ip) injection of cyclophosphamide (CYP) or intravesical instillation of acetone, using freely moving, non-catheterized conscious rats. Methods Female Sprague-Dawley rats were used. Cystitis was induced by ip injection of CYP (100 and 200mg/kg) or intravesical instillation of acetone (10, 30 and 50%) via a polyethylene catheter temporarily inserted into the bladder through the urethra. Then the incidence of nociceptive behavior (immobility with decreased breathing rates) was scored. Voided urine was collected simultaneously and continuously to measure bladder capacity. The plasma extravasation in the bladder was quantified by an evans blue (EB) dye leakage technique. Results CYP (100mg/kg, ip) induced nociceptive behavior without affecting bladder capacity or EB concentration in the bladder. A higher dose of CYP (200mg/kg, ip) decreased bladder capacity and increased EB levels as well as nociceptive behavior. In contrast, intravesical instillation of acetone (30%) decreased bladder capacity and increased EB levels, but evoked nociceptive behavior less frequently compared with CYP-treated animals. In capsaicin pretreated rats, nociceptive behavior induced by CYP or acetone was reduced; however, the overall effects of CYP or acetone on bladder capacity and bladder EB levels were unaffected. Conclusions These results suggest that there is a difference in the induction process of nociceptive behavior and small bladder capacity after two different types of bladder irritation and that C-fiber sensitization is more directly involved in pain sensation than reduced bladder capacity. PMID:19618450

The human gastric pathogen Helicobacter pylori has a potential acetone carboxylase that enhances its ability to colonize mice

Directory of Open Access Journals (Sweden)

Weinberg Michael V

2008-01-01

Full Text Available Abstract Background Helicobacter pylori colonizes the human stomach and is the etiological agent of peptic ulcer disease. All three H. pylori strains that have been sequenced to date contain a potential operon whose products share homology with the subunits of acetone carboxylase (encoded by acxABC from Xanthobacter autotrophicus strain Py2 and Rhodobacter capsulatus strain B10. Acetone carboxylase catalyzes the conversion of acetone to acetoacetate. Genes upstream of the putative acxABC operon encode enzymes that convert acetoacetate to acetoacetyl-CoA, which is metabolized further to generate two molecules of acetyl-CoA. Results To determine if the H. pylori acxABC operon has a role in host colonization the acxB homolog in the mouse-adapted H. pylori SS1 strain was inactivated with a chloramphenicol-resistance (cat cassette. In mouse colonization studies the numbers of H. pylori recovered from mice inoculated with the acxB:cat mutant were generally one to two orders of magnitude lower than those recovered from mice inoculated with the parental strain. A statistical analysis of the data using a Wilcoxin Rank test indicated the differences in the numbers of H. pylori isolated from mice inoculated with the two strains were significant at the 99% confidence level. Levels of acetone associated with gastric tissue removed from uninfected mice were measured and found to range from 10–110 μmols per gram wet weight tissue. Conclusion The colonization defect of the acxB:cat mutant suggests a role for the acxABC operon in survival of the bacterium in the stomach. Products of the H. pylori acxABC operon may function primarily in acetone utilization or may catalyze a related reaction that is important for survival or growth in the host. H. pylori encounters significant levels of acetone in the stomach which it could use as a potential electron donor for microaerobic respiration.

Cathodic reduction of benzil in acetone and in dichloromethane

Energy Technology Data Exchange (ETDEWEB)

Quintanilla, Gloria [Departamento de Quimica Organica, Universidad de Alcala, 28871 Alcala de Henares, Madrid (Spain)], E-mail: gloria.quintanilla@uah.es; Liebeck, Miriam; Bengtsson, Carina; Arnold, Lena; Barba, Fructuoso [Departamento de Quimica Organica, Universidad de Alcala, 28871 Alcala de Henares, Madrid (Spain)

2008-02-15

The cathodic reduction of benzil has been carried out at a controlled potential on a mercury cathode in two different SSE (solvent-supporting-electrolyte) conditions: (a) acetone/lithium perchlorate in absence of electrophile where 2,3-diphenyl-5-methyl-furan and 1,2-diphenyl-2-hydroxy-1,4-pentanedione were obtained as main products and (b) dichloromethane/tetrabuthylammonium chloride with the addition of oxalyl chloride as electrophile, where a fast electron transfer took place.

Preparation, GIAO NMR Calculations and Acidic Properties of Some Novel 4,5-dihydro-1H-1,2,4-triazol-5-one Derivatives with Their Antioxidant Activities

Directory of Open Access Journals (Sweden)

Havva Aksu

2008-01-01

Full Text Available Six novel 3-alkyl(aryl-4-(p-nitrobenzoylamino-4,5-dihydro-1H-1,2,4-triazol-5- ones (2a-f were synthesized by the reactions of 3-alkyl(aryl-4-amino-4,5-dihydro-1H- 1,2,4-triazol-5-ones (1a-f with p-nitrobenzoyl chloride and characterized by elemental analyses and IR, 1H-NMR, 13C-NMR and UV spectral data. The newly synthesized compounds 2 were titrated potentiometrically with tetrabutylammonium hydroxide in four non-aqueous solvents such as acetone, isopropyl alcohol, tert-butyl alcohol and N,Ndimethylformamide, and the half-neutralization potential values and the corresponding pKa values were determined for all cases. Thus, the effects of solvents and molecular structure upon acidity were investigated. In addition, isotropic 1H and 13C nuclear magnetic shielding constants of compounds 2 were obtained by the gauge-including-atomic-orbital (GIAO method at the B3LYP density functional level. The geometry of each compound has been optimized using the 6-311G basis set. Theoretical values were compared to the experimental data. Furthermore, these new compounds and five recently reported 3-alkyl-4-(2- furoylamino-4,5-dihydro-1H-1,2,4-triazol-5-ones (3a-c,e,f were screened for their antioxidant activities.

Determination of Doxorubicin in Stealth Hyalurionic Acid-Based Nanoparticles in Rat Plasma by the Liquid-Liquid Nanoparticles-Breaking Extraction Method: Application to a Pharmacokinetic Study.

Science.gov (United States)

Han, Xiaopeng; Wei, Wei; Zhong, Lu; Luo, Cong; Wu, Chunnuan; Jiang, Qikun; Sun, Jin

2016-09-01

An efficient extraction of doxorubicin (Dox) from homemade stealth hyalurionic acid (HA)-based nanoparticles (NPs) in rat plasma could not be performed by previously published methods. Therefore, we attempted to establish the novel NPs-breaking and UPLC-MS-MS method for evaluating the pharmacokinetic profiles of the homemade stealth HA NPs in rats. The pretreatment method of plasma samples used the liquid-liquid extraction method with isopropyl alcohol as NPs-breaking and protein-precipitating solvents, and the NPs-breaking efficiency of isopropyl alcohol was as high as 97.2%. The analyte and gliclazide (internal standard) were extracted from plasma samples with isopropyl alcohol and were separated on UPLC BEH C18 with a mobile phase consisting of methanol and water (containing 0.1% formic acid). The method demonstrated good linearity at the concentrations ranging from 5 to 5,000 ng/mL. The intra- and interday relative standard deviations were >10%. Finally, the method was successfully applied to a pharmacokinetic study of homemade stealth HA-based NPs in rats following intravenous administration. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Antioxidant effect of water and acetone extracts of Fucus vesiculosuson oxidative stability of skin care emulsions

DEFF Research Database (Denmark)

Poyato, Candelaria; Thomsen, Birgitte Raagaard; Hermund, Ditte Baun

2017-01-01

A water and an acetone extract of the Icelandic brown algae Fucus vesiculosus were evaluated as potential natural sources of antioxidant compounds in skin care emulsions. To assess their efficacy in inhibiting lipid oxidation caused by photo- or thermoxidation, they were stored in darkness and room...... temperature. High temperature also caused greater increments in the droplet size of the emulsions. The analysis of the tocopherol content, peroxide value and volatile compounds during the storage revealed that, whereas both water and acetone extracts showed (at 2 mg/g of emulsion) protective effect against...

Brain SPECT with /sup 123/I-isopropyl amphetamine in epilepsy

Energy Technology Data Exchange (ETDEWEB)

Biersack, H.J.; Reske, S.N.; Rasche, A.; Reichmann, K.; Winkler, C.; Froescher, W.; Kluenenberg, H.

1983-04-01

Ten patients were studied with N-isopropyl I-123 p-iodoamphetamine. Single photon emission computed tomography (SPECT) was carried out by hand of a rotating gamma camera system (Gammatome T9000/CGR, high resolution collimator). During 1 rotation (360/sup 0/) 64 frames (4k matrix) were acquired within 20 min 1 hour after injection of 6.5 mCi I-123 labeled amphetamine. The content of I-124 was less than 2%. After reconstruction of transverse slices coronar and sagittal reconstructions were rapidly performed using an array processor. Nine patients suffered from epilepsy and one from severe migraine. Excellent differentiation between gray and white matter of the cerebral cortex and the basal ganglia was evident in all of the cases. In 2 out of 3 patients with epilepsy and negative CT results SPECT revealed circumscribed areas with increased amphetamine uptake in accordance with the EEG findings. In 4 out of 6 cases with positive CT findings SPECT lesions with diminished amphetamine uptake could be established. One patient with severe migraine showed focal increased amphetamine uptake in accordance with the respective clinical results.

Electron thermal capacity in plasma generated at cavitation bubble collapse in D-acetone

International Nuclear Information System (INIS)

Kostenko, B.F.; Pribis, J.

2004-01-01

The latest experimental data on nuclear reaction product registration at cavitation bubble collapse in deuterated acetone (C 3 D 6 O) still argue in favour of existence of a new possibility to realize the thermonuclear synthesis. Theoretical description based on numerical solution of simultaneous conservation equations for gaseous and liquid phases also confirms this possibility, although it requires further more precise definitions. In particular, description of electron degrees of freedom in dense nonequilibrium plasma generated at the final stage of bubble collapse need specification. Calculations of electron thermal capacity in the deuterated acetone multiple ionization region at electron temperatures T e ≅ 10 4 K and above and compression range ρ/ρ 0 ≅ 1 - 100 have been fulfilled on the basis of direct numerical solution of equation for chemical potential. (author)

Biodistribution of N-isopropyl-p-iodoamphetamine

International Nuclear Information System (INIS)

Hoshi, Hiroaki; Jinnouchi, Seishi; Watanabe, Katsushi; Ueda, Takashi; Yamaguchi, Tadatoshi

1987-01-01

Biodistribution of N-isopropyl-p-iodoamphetamine (IMP) was experimentally studied for evaluating the usefullness of this radiopharmaceuticals for cerebral perfusion scintigraphy. IMP labeled with radioactive iodine (I-125, I-131), was injected intravenously in awake animals. The activity in the brain of male ddY mice injected 3.7 kBq (0.1 μCi) of I-125 IMP reached 8.0 (%Dose/g) at 10 min. after injection and it was almost constant till 120 min. Activity in the lung and heart was the highest just after injection, and rapidly decreased in the constant level lasting 30 min. to 120 min. Activity in the liver increased slowly and reached peak level at 60 min. Autoradiograms of male ddY mice injected 1.85 MBq (50 μCi) of I-131 IMP showed almost same activity in the spinal cord as the brain. Activities of I-131 IMP in normal brain of Sprague-Dawley rats injected 7.4 MBq (200 μCi) of I-131 IMP were 2.68 - 3.2 (%Dose/g) in the cerebral cortex and 0.59 - 0.66 (%Dose/g) in the white matter at 1 min. after injection. Activities in the cerebral cortex were slightly increased at 60 min. after injection and the activities in the white matter increased markedly at 60 min. and 6 hrs. after injection. The cerebral cortex to white matter ratios were about 5 at 1 min. or 10 min. and about 1 at 60 min. or 6 hrs. after injection. Autoradiograms of normal and ischemic rat brain showed local cerebral blood flow image, but the contrast between the gray matter and the white matter decreased at 60 min. or 6 hrs. Our study on the biodistribution of IMP showed the usefullness of this agent in cerebral perfusion imaging, and may be informative for the interpretation of images. (author)

Synergistic effects of sodium 
ascorbate and acetone to restore compromised bond strength 
after enamel bleaching.

Science.gov (United States)

Boruziniat, Alireza; Manafi, Safa; Cehreli, Zafer C

To evaluate the effect of a new experimental solution containing sodium ascorbate (SA) and acetone on reversing compromised bonding to enamel immediately after bleaching. The buccal surface of intact, extracted human premolars (n = 60) was bleached. The teeth were then randomly assigned to 6  groups according to the type of pretreatment applied prior to adhesive procedures: 10% SA in acetone-water solution applied for 1 and 5 min (groups 1 and 2, respectively); aqueous solution of 10% SA applied for 10 min (group 3); 100% acetone applied for 10 min (group 4); no pretreatment (negative control; group 5). An additional group (positive control; group 6) comprised unbleached teeth (n = 12). Two composite microcylinders were bonded on each specimen for evaluation of microshear bond strength (MBS) and failure modes. Data were analyzed using the one-way ANOVA and Tukey's post-hoc and chi-square tests at P = 0.05. Groups 1 and 2 yielded similar MBS values to groups 4 and 6 (positive control). The mean MBS of groups 3 and 5 (negative control) were similar, and significantly lower than that of the positive control group. The application of 10% SA in an acetone-water solution prior to bonding procedures can restore compromised enamel bond strength to its unbleached state within a clinically acceptable time of 1 min.

Peculiar behavior of MWW materials in aldol condensation of furfural and acetone

Czech Academy of Sciences Publication Activity Database

Kikhtyanin, O.; Eliášová, Pavla; Jindrová, T.; Kubička, D.

2014-01-01

Roč. 43, č. 27 (2014), s. 10628-10641 ISSN 1477-9226 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : acetone * aldehydes * batch reactors Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.197, year: 2014

Treatment of acetone waste gases using slurry-phase airlift embedded with polyacrylamide-entrapped cell beads.

Science.gov (United States)

Hwang, Sz-Chwun John; Lin, Yun-Huin; Huang, Ku Shu; Lyuu, Jyuhn-Yih; Hou, Cheng-Ting; Chen, Hsin-Hua; He, Sin-Yi

2009-10-01

Acetone is the most common chemical used in the Hsin-chu Science Park in Taiwan. The three-phase airlift bioreactor was designed to absorb acetone into the 39 L of medium solution and then degraded by 2-L polyacrylamide (PAA)-entrapped Thiosphaera pantotropha cell beads. The airlift medium was successfully regenerated and circulated for more than 5 months. The elimination capacity of 350-part per million (ppm) acetone at 10 L x min(-1) was 258.4 g x m(-3) hr(-1) (160.4 g-C x m(-3) hr(-1)) with 100% removal efficiency in Stage II, higher than previously reported biofiltration results. The maximum chemical oxygen demand:nitrogen ratio of 100:2.9 is achieved, and a balanced nutrient state was indicated by the change in redox potential. The pH of the system was maintained at neutral because of the strong buffer agent added to the medium (final buffer intensity, beta = 1.18 x 10(-2) M). The PAA-entrapped cell beads could also provide a good barrier for high salinity gradient environment and the inoculum source to maintain steady operation of the system.

The combustion chemistry of a fuel tracer: Measured flame speeds and ignition delays and a detailed chemical kinetic model for the oxidation of acetone

Energy Technology Data Exchange (ETDEWEB)

Pichon, S.; Black, G.; Simmie, J.M.; Curran, H.J. [Combustion Chemistry Centre, National University of Ireland, Galway (Ireland); Chaumeix, N.; Yahyaoui, M. [Institut de Combustion Aerothermique Reactivite et Environnement, CNRS, Orleans (France); Donohue, R. [Information Technology, National University of Ireland, Galway (Ireland)

2009-02-15

Acetone ignition delay and stretch-free laminar flame speed measurements have been carried out and a kinetic model has been developed to simulate these and literature data for acetone and for ketene, which was found to be an important intermediate in its oxidation. The mechanism has been based on one originally devised for dimethyl ether and modified through validation of the hydrogen, carbon monoxide and methane sub-mechanisms. Acetone oxidation in argon was studied behind reflected shock waves in the temperature range 1340-1930 K, at 1 atm and at equivalence ratios of 0.5, 1 and 2; it is also shown that the addition of up to 15% acetone to a stoichiometric n-heptane mixture has no effect on the measured ignition delay times. Flame speeds at 298 K and 1 atm of pure acetone in air were measured in a spherical bomb; a maximum flame speed of {proportional_to}35 cm s{sup -1} at {phi}=1.15 is indicated. (author)

Recent advances on conversion and co-production of acetone-butanol-ethanol into high value-added bioproducts.

Science.gov (United States)

Xin, Fengxue; Dong, Weiliang; Jiang, Yujia; Ma, Jiangfeng; Zhang, Wenming; Wu, Hao; Zhang, Min; Jiang, Min

2018-06-01

Butanol is an important bulk chemical and has been regarded as an advanced biofuel. Large-scale production of butanol has been applied for more than 100 years, but its production through acetone-butanol-ethanol (ABE) fermentation process by solventogenic Clostridium species is still not economically viable due to the low butanol titer and yield caused by the toxicity of butanol and a by-product, such as acetone. Renewed interest in biobutanol as a biofuel has spurred technological advances to strain modification and fermentation process design. Especially, with the development of interdisciplinary processes, the sole product or even the mixture of ABE produced through ABE fermentation process can be further used as platform chemicals for high value added product production through enzymatic or chemical catalysis. This review aims to comprehensively summarize the most recent advances on the conversion of acetone, butanol and ABE mixture into various products, such as isopropanol, butyl-butyrate and higher-molecular mass alkanes. Additionally, co-production of other value added products with ABE was also discussed.

Efficacy and dermal tolerance of a novel alcohol-based skin antiseptic in horses.

Science.gov (United States)

Tannahill, Victoria J; Cogan, Tristan; Allen, Kate; Acutt, Elizabeth; Busschers, Evita

2018-04-14

To determine the efficacy and dermal tolerance of a novel alcohol-based skin antiseptic (ABSA) in horses. Experimental study. Systemically healthy horses (n = 25) with no history or clinical signs of skin disease. Four clipped sites on the abdomen were randomly assigned to a skin preparation protocol: saline (negative control; NC), chlorhexidine gluconate followed by isopropyl alcohol (positive control; PC), saline followed by the ABSA (ABSA A), or a commercially available horse shampoo followed by the ABSA (ABSA B). Microbiological swabs were obtained from each site and cultured on MacConkey and mannitol salt agar plates. Colony-forming units were counted 18-24 hours later. All sites were scored for signs of skin reaction before, immediately after, 1 hour after, and 24 hours after skin preparation. The PC, ABSA A, and ABSA B methods reduced skin microbial burden compared with the NC method (P horses required veterinary treatment. The ABSA preparations tested in this study were as effective and well tolerated as a chlorhexidine gluconate-based method, but required less time in healthy horses. The ABSA tested here provides an efficacious, fast-acting, and well-tolerated alternative to achieve skin antisepsis in healthy horses. These results justify further investigation in clinical cases. © 2018 The American College of Veterinary Surgeons.

Dissociative electron attachment studies on acetone

International Nuclear Information System (INIS)

Prabhudesai, Vaibhav S.; Tadsare, Vishvesh; Ghosh, Sanat; Gope, Krishnendu; Davis, Daly; Krishnakumar, E.

2014-01-01

Dissociative electron attachment (DEA) to acetone is studied in terms of the absolute cross section for various fragment channels in the electron energy range of 0–20 eV. H − is found to be the most dominant fragment followed by O − and OH − with only one resonance peak between 8 and 9 eV. The DEA dynamics is studied by measuring the angular distribution and kinetic energy distribution of fragment anions using Velocity Slice Imaging technique. The kinetic energy and angular distribution of H − and O − fragments suggest a many body break-up for the lone resonance observed. The ab initio calculations show that electron is captured in the multi-centered anti-bonding molecular orbital which would lead to a many body break-up of the resonance

Solubility and Standard Gibb's energies of transfer of alkali metal perchlorates, tetramethyl- and tetraethylammonium from water to aqua-acetone solvents

International Nuclear Information System (INIS)

Kireev, A.A.; Pak, T.G.; Bezuglyj, V.D.

1996-01-01

Solubilities of KClO 4 , RbClO 4 , CsClO 4 , (CH 3 ) 4 NClO 4 , (C 2 M 5 ) 4 NClO 4 in water and water-acetone mixtures are determined by the method of isothermal saturation at 298.15 K. Dissociation constants of alkali metal perchlorates are found by conductometric method. Solubility products and standard Gibbs energies of transfer of corresponding electrolytes from water into water-acetone solvents are calculated. The character of transfer Gibbs energy dependence on solvent composition is explained by preferred solvation of cations by acetone molecules and anions-by water molecules. Features of tetraalkyl ammonium ions are explained by large changes in energy of cavity formation for these ions

Achieving concentrated graphene dispersions in water/acetone mixtures by the strategy of tailoring Hansen solubility parameters

International Nuclear Information System (INIS)

Yi Min; Shen Zhigang; Zhang Xiaojing; Ma Shulin

2013-01-01

Although exfoliating graphite to give graphene paves a new way for graphene preparation, a general strategy of low-boiling-point solvents and high graphene concentration is still highly required. In this study, using the strategy of tailoring Hansen solubility parameters (HSP), a method based on exfoliation of graphite in water/acetone mixtures is demonstrated to achieve concentrated graphene dispersions. It is found that in the scope of blending two mediocre solvents, tailoring the HSP of water/acetone mixtures to approach the HSP of graphene could yield graphene dispersions at a high concentration of up to 0.21 mg ml -1 . The experimentally determined optimum composition of the mixtures occurs at an acetone mass fraction of ∼75%. The trend of concentration varying with mixture compositions could be well predicated by the model, which relates the concentration to the mixing enthalpy within the scope of HSP theory. The resultant dispersion is highly stabilized. Atomic force microscopic statistical analysis shows that up to ∼50% of the prepared nanosheets are less than 1 nm thick after 4 h sonication and 114g centrifugation. Analyses based on diverse characterizations indicate the graphene sheets to be largely free of basal plane defects and oxidation. The filtered films are also investigated in terms of their electrical and optical properties to show reasonable conductivity and transparency. The strategy of tailoring HSP, which can be easily extended to various solvent systems, and water/acetone mixtures here, extends the scope for large-scale production of graphene in low-boiling-point solutions.

Investigation of hydrolysis products in the acetone-butanol fermentation of vegetable agricultural waste materials

Energy Technology Data Exchange (ETDEWEB)

Nakhmanovich, B M

1960-01-01

Determinations of the fundamental chemical composition of corn stalk, sunflower husk, and hemp scutch by chromatography were reported, e.g. pentoses (1.98, 1.98, 2.01%), hexoses (1.59, 1.72, 2.01% respectively.) and various amino acids (arginine, asparagine, histidine, glutamine, glycine, lysine, proline, serine, tyrosine, threonine, cysteine, cystine, alanine, and aspartic and glutamic acids). The sterilized products from the hydrolysis (pentoses, hexoses) in a combined mixture with a meal mash were normally fermented at 37/sup 0/ in the presence of acetone-butanol bacteria for 40 to 48 hours, yielding 10.46 to 12.50% of acetone, 15.09 to 18.0% of butanol, 3.79 to 6.08% of ethanol (a total yielding being 30 to 42% of solvents).

Frozen concentration fluctuations in a poly(N-isopropyl acrylamide) gel studied by neutron spin echo and small-angle neutron scattering

CERN Document Server

Koizumi, S; Richter, D; Schwahn, D; Faragó, B; Annaka, M

2002-01-01

By employing neutron spin echo and small-angle neutron scattering, we determined the structure factor of the frozen concentration fluctuations on nano-length scales in a swollen poly(N-isopropyl acrylamide) gel. The frozen contribution, showing a plateau at the low scattering wavenumber q (0.02 A sup - sup 1), is intimately related to the abnormal butterfly scattering pattern appearing at low q under deformation. (orig.)

Photofragment spectrum of acetone

International Nuclear Information System (INIS)

Hancock, Graham; Wilson, K.R.

1974-01-01

The photodissociation of acetone at 266.2 nm has been investigated by photofragment spectroscopy. A molecular beam of CH 3 COCH 3 is crossed by pulses of polarized uv light from a powerful fourth harmonic neodymium laser system, and the recoiling CH 3 and CH 3 CO photofragments detected with a quadrupole mass spectrometer. Both the flight time distributions and the masses of the fragments are measured, leading to a determination of the energy partitioning in the photodissociation process; it is found that the methyl and acetyl fragments together carry 43% of the available energy in translation, with the remaining 57% in fragment internal excitation. The angular distribution of fragments with respect to the polarization direction of the laser beam was found to be isotropic. The long lifetime of the initially produced singlet state should give a smoothing of the angular distribution, and this tendency towards isotropy could be further increased by a non-planar mode of dissociation of the excited molecule. Both statistical and impulsive dissociation models can fit the observed average energy partitioning, with present data enable to distinguish between the two possibilities, which, however, could be differentiated with further crossed molecular and laser beam experiments

Electron Thermal Capacity in Plasma Generated at Cavitation Bubble Collapse in D-acetone

CERN Document Server

Kostenko, B F

2004-01-01

The latest experimental data on nuclear reaction product registration at cavitation bubble collapse in deuterated acetone (C$_3$D$_6$O) still argue in favour of existence of a new possibility to realize the thermonuclear synthesis. Theoretical description based on numerical solution of simultaneous conservation equations for gaseous and liquid phases also confirms this possibility, although it requires further more precise definitions. In particular, description of electron degrees of freedom in very dense nonequilibrium plasma generated at the final stage of bubble collapse needs specification. In the present paper, calculations of electron thermal capacity in the deuterated acetone multiple ionization region at electron temperatures $T_e \\simeq 10^4 $ K and above and compression range $\\rho/\\rho_0 \\simeq 1 \\div 100$ have been fulfilled on the basis of direct numerical solution of equation for chemical potential.

Proceedings of Tripartite Conference on Submarine Medicine and IEP B-52 - France, United Kingdom, United States (6th) Held in Groton, Connecticut on 1-4 June 1987

Science.gov (United States)

1990-10-03

limits were provided for the following: Chlorcbenzene Cumene (Isopropyl benzene) Cyclohexane Ethyl benzene Heptane Hexane Isopropyl alcohol Methyl...hydrogen removal The removal of carbon monoxyde and hydrogen is done by the catalytic burner whose active product is platinum oxyde deposited on corundum...alumina). The weight of the platinum oxyde represents 1 % of the weight of the catalyst. The CO and H= catalysis is complete at 50’C. For safety, the

Determination and modeling of binary and ternary solid-liquid phase equilibrium for the systems formed by 3,5-dinitrobenzoic acid, m-nitrobenzoic acid and acetone

International Nuclear Information System (INIS)

Li, Xinbao; Du, Cunbin; Zhao, Hongkun

2017-01-01

Highlights: • The solubility of 3,5-dinitrobenzoic acid in acetone was determined. • Solubility of m-nitrobenzoic acid + 3,5-dinitrobenzoic acid + acetone was determined. • Three ternary phase diagrams were constructed for the ternary system. • The ternary phase diagrams were calculated by Wilson model and NRTL model. - Abstract: The solubility of 3,5-dinitrobenzoic acid in acetone at the temperatures ranging from (283.15 to 318.15) K and the mutual solubility of the ternary m-nitrobenzoic acid + 3,5-dinitrobenzoic acid + acetone system at (283.15, 298.15 and 313.15) K were determined experimentally by using the isothermal saturation method under atmosphere pressure (101.2 kPa). Three isothermal ternary phase diagrams were constructed according to the measured mutual solubility data. In each ternary phase diagram, there was one co-saturated point, two boundary curves, and three crystalline regions. The modified Apelblat equation, λh equation, NRTL model and Wilson model were used to correlate the solubility of 3,5-dinitrobenzoic acid in acetone; and the NRTL and Wilson models, the mutual solubility for the ternary m-nitrobenzoic acid + 3,5-dinitrobenzoic acid + acetone system. The value of root-mean-square deviation (RMSD) was 8.53 × 10 −4 for the binary system of 3,5-dinitrobenzoic acid + acetone; and the largest value of RMSD was 81.08 × 10 −4 for the ternary system.

Laminar burning velocities of acetone in air at room and elevated temperatures

NARCIS (Netherlands)

Nilsson, E.J.K.; Goey, de L.P.H.; Konnov, A.

2013-01-01

Laminar burning velocities of acetone + air mixtures at initial gas mixture temperatures of 298, 318, 338 and 358 K are reported. Non-stretched flames were stabilized on a perforated plate burner at 1 atm, and laminar burning velocities were determined using the heat flux method, at conditions where

Preparation and Characterization of Epoxy Resin Cross-Linked with High Wood Pyrolysis Bio-Oil Substitution by Acetone Pretreatment

Directory of Open Access Journals (Sweden)

Yi Liu

2017-03-01

Full Text Available The use of cost effective solvents may be necessary to store wood pyrolysis bio-oil in order to stabilize and control its viscosity, but this part of the production system has not been explored. Conversely, any rise in viscosity during storage, that would occur without a solvent, will add variance to the production system and render it cost ineffective. The purpose of this study was to modify bio-oil with a common solvent and then react the bio-oil with an epoxy for bonding of wood without any loss in properties. The acetone pretreatment of the bio-oil/epoxy mixture was found to improve the cross-linking potential and substitution rate based on its mechanical, chemical, and thermal properties. Specifically, the bio-oil was blended with epoxy resin at weight ratios ranging from 2:1 to 1:5 and were then cured. A higher bio-oil substitution rate was found to lower the shear bond strength of the bio-oil/epoxy resins. However, when an acetone pretreatment was used, it was possible to replace the bio-oil by as much as 50% while satisfying usage requirements. Extraction of the bio-oil/epoxy mixture with four different solvents demonstrated an improvement in cross-linking after acetone pretreatment. ATR-FTIR analysis confirmed that the polymer achieved a higher cross-linked structure. DSC and TGA curves showed improved thermal stability with the addition of the acetone pretreatment. UV-Vis characterization showed that some functional groups of the bio-oil to epoxy system were unreacted. Finally, when the resin mixture was utilized to bond wood, the acetone pretreatment coupled with precise tuning of the bio-oil:epoxy ratio was an effective method to control cross-linking while ensuring acceptable bond strength.

A path integral molecular dynamics study of the hyperfine coupling constants of the muoniated and hydrogenated acetone radicals

Energy Technology Data Exchange (ETDEWEB)

Oba, Yuki; Kawatsu, Tsutomu; Tachikawa, Masanori, E-mail: tachi@yokohama-cu.ac.jp [Quantum Chemistry Division, Yokohama City University, Seto 22-2, Kanazawa-ku, Yokohama 236-0027 (Japan)

2016-08-14

The on-the-fly ab initio density functional path integral molecular dynamics (PIMD) simulations, which can account for both the nuclear quantum effect and thermal effect, were carried out to evaluate the structures and “reduced” isotropic hyperfine coupling constants (HFCCs) for muoniated and hydrogenated acetone radicals (2-muoxy-2-propyl and 2-hydoxy-2-propyl) in vacuo. The reduced HFCC value from a simple geometry optimization calculation without both the nuclear quantum effect and thermal effect is −8.18 MHz, and that by standard ab initio molecular dynamics simulation with only the thermal effect and without the nuclear quantum effect is 0.33 MHz at 300 K, where these two methods cannot distinguish the difference between muoniated and hydrogenated acetone radicals. In contrast, the reduced HFCC value of the muoniated acetone radical by our PIMD simulation is 32.1 MHz, which is about 8 times larger than that for the hydrogenated radical of 3.97 MHz with the same level of calculation. We have found that the HFCC values are highly correlated with the local molecular structures; especially, the Mu—O bond length in the muoniated acetone radical is elongated due to the large nuclear quantum effect of the muon, which makes the expectation value of the HFCC larger. Although our PIMD result calculated in vacuo is about 4 times larger than the measured experimental value in aqueous solvent, the ratio of these HFCC values between muoniated and hydrogenated acetone radicals in vacuo is in reasonable agreement with the ratio of the experimental values in aqueous solvent (8.56 MHz and 0.9 MHz); the explicit presence of solvent molecules has a major effect on decreasing the reduced muon HFCC of in vacuo calculations for the quantitative reproduction.

A path integral molecular dynamics study of the hyperfine coupling constants of the muoniated and hydrogenated acetone radicals

International Nuclear Information System (INIS)

Oba, Yuki; Kawatsu, Tsutomu; Tachikawa, Masanori

2016-01-01

The on-the-fly ab initio density functional path integral molecular dynamics (PIMD) simulations, which can account for both the nuclear quantum effect and thermal effect, were carried out to evaluate the structures and “reduced” isotropic hyperfine coupling constants (HFCCs) for muoniated and hydrogenated acetone radicals (2-muoxy-2-propyl and 2-hydoxy-2-propyl) in vacuo. The reduced HFCC value from a simple geometry optimization calculation without both the nuclear quantum effect and thermal effect is −8.18 MHz, and that by standard ab initio molecular dynamics simulation with only the thermal effect and without the nuclear quantum effect is 0.33 MHz at 300 K, where these two methods cannot distinguish the difference between muoniated and hydrogenated acetone radicals. In contrast, the reduced HFCC value of the muoniated acetone radical by our PIMD simulation is 32.1 MHz, which is about 8 times larger than that for the hydrogenated radical of 3.97 MHz with the same level of calculation. We have found that the HFCC values are highly correlated with the local molecular structures; especially, the Mu—O bond length in the muoniated acetone radical is elongated due to the large nuclear quantum effect of the muon, which makes the expectation value of the HFCC larger. Although our PIMD result calculated in vacuo is about 4 times larger than the measured experimental value in aqueous solvent, the ratio of these HFCC values between muoniated and hydrogenated acetone radicals in vacuo is in reasonable agreement with the ratio of the experimental values in aqueous solvent (8.56 MHz and 0.9 MHz); the explicit presence of solvent molecules has a major effect on decreasing the reduced muon HFCC of in vacuo calculations for the quantitative reproduction.

Relationships between changes in Holstein cow’s body condition, acetone and urea content in milk and cervical mucus and sperm survival

Directory of Open Access Journals (Sweden)

Jan Beran

2012-01-01

Full Text Available The objectives of this study were to evaluate the relationship between changes in Holstein cow’s body condition score (BCS, acetone and urea content in the milk and cervical mucus (CM and sperm survival in CM. At insemination, samples of milk and CM were collected from 64 Holstein cows. Content of acetone and urea were determined. Sperm motility was assessed subjectively at the beginning and after 30, 60 and 90 minutes of the short-term heat test in CM. Data about evaluation of cow’s BCS were taken from farm evidence. The data set was analyzed using SAS/STAT software. Effect of change in cow’s BCS one month before insemination was significant only in relation to the acetone content in milk (P < 0.05. Higher values of acetone and urea content were found in the CM compared to milk. Higher levels of both metabolites were detected in primiparous cows and in cows on the third and subsequent lactation, resp. in cows inseminated 3 times and more. The highest values of both metabolites negatively affected sperm survival during the short-term heat test, especially after 90 minutes (P < 0.05–0.01. Significant decreases (P < 0.05–0.01 were detected in cows with the highest level of acetone and urea.

Regional cerebral blood flow in Parkinson's disease measured with N-isopropyl-p-[123I]iodoamphetamine (IMP) SPECT

International Nuclear Information System (INIS)

Odano, Ikuo; Nishihara, Mamiko; Hayashi, Hiroko; Higuchi, Shoichi; Sakai, Kunio; Ishikawa, Atsushi; Ibayashi, Katsuhiko.

1992-01-01

N-isopropyl-p-[ 123 I]iodoamphetamine (IMP) SPECT studies were performed on 21 patients (13 females; 45-73 yrs) with idiopathic Parkinson's disease (PD) and 10 age-matched normal controls (39-69 yrs). Regional cerebral blood flow (rCBF) was quantitatively measured by the arterial blood sampling method. When compared with normal controls, global CBF, and rCBF in the frontal cortex and in the basal ganglia were reduced 22.1% (p 123 I-IMP SPECT imaging is useful for evaluation and follow-up of patients with PD. (author)

Crystal structure of isopropyl 2-hydroxy-2-phenylacetate: a pharmacopoeia reference standard

Directory of Open Access Journals (Sweden)

Ivan Isaiev

2017-05-01

Full Text Available The title compound, C11H14O3, is used as a pharmacopoeia reference standard for determining impurities in the drug Pregabalin, used for the treatment of epilepsy and diabetic neuropathic pain. The molecule is far from being planar, with the dihedral angle between the planes of the aromatic ring and the carboxyl fragment (O—C=O being 76.1 (6°. The isopropyl substituent is located in a synperiplanar position relative to the C=O bond and is turned so that the C—O—C—H torsion angle is −43.7°. In the crystal, bifurcated O—H...(O,O hydrogen bonds, enclosing R12(5 ring motifs, lead to the formation of chains propagating along the c-axis direction. Inversion-related chains are linked by the C—H...O hydrogen bonds, forming undulating layers lying parallel to the bc plane.

Electricity generation and removal performance of a microbial fuel cell using sulfonated poly (ether ether ketone) as proton exchange membrane to treat phenol/acetone wastewater.

Science.gov (United States)

Wu, Hao; Fu, Yu; Guo, Chunyu; Li, Yanbo; Jiang, Nanzhe; Yin, Chengri

2018-07-01

The microbial fuel cell (MFC) has emerged as a promising technology for wastewater treatment and energy recovery, but the expensive cost of proton exchange membranes (PEMs) is a problem that need to be solved. In this study, a two-chamber MFC based on our self-made PEM sulfonated poly (ether ether ketone) membrane was set up to treat phenol/acetone wastewater and synchronously generate power. The maximum output voltage was 240-250 mV. Using phenol and acetone as substrates, the power generation time in an operation cycle was 289 h. The MFC exhibited good removal performance, with no phenol or acetone detected, respectively, when the phenol concentration was lower than 50 mg/L and the acetone concentration was lower than 100 mg/L. This study provides a cheap and eco-friendly way to treat phenol/acetone wastewater and generate useful energy by MFC technology. Copyright © 2018 Elsevier Ltd. All rights reserved.

Comparative Observation of Silver Nano and Microstructures Deposited from Aerosol and Fog

Directory of Open Access Journals (Sweden)

Zheltova Anna

2017-01-01

Full Text Available A comparative study of the structure and fractal properties of arrays of the silver nano-/micro-particles deposited on the silicon substrate both from the aerosol and fog showed that the form of the silver individual particles and nano-/microstructures greatly depends on the deposition conditions. By passing an aerosol through isopropyl alcohol, the formation of fractal aggregates of the silver nano-/micro-particles both in the air and in alcohol was observed. Deposition of the silver nano-/micro-particles in the atmosphere of the saturated isopropyl alcohol vapours led to formation of fog. Micro-droplets of the silver colloidal solution were deposited on the substrate. The further evaporation of alcohol created the silver nano/microstructures in the form of annular layers. It was found that the concerned annular layers contained silver particles of the same shape in the form of a Crescent (or Janus-nano-/microparticles. The nature of discovered effects is discussed.

Determination and modeling of the solubility of (limonin in methanol or acetone + water) binary solvent mixtures at T = 283.2 K to 318.2 K

International Nuclear Information System (INIS)

Fan, Jie-Ping; Zheng, Bing; Liao, Dan-Dan; Yu, Jia-Xin; Cao, Ya-Hui; Zhang, Xue-Hong; Zhu, Jian-Hang

2016-01-01

Highlights: • The solubilities of limonin were measured in the binary solvent mixtures methanol + water and acetone + water. • The solubility data were correlated by nine models. • The solubility of limonin had a maximum point at 0.9 mol fraction of acetone in acetone + water mixtures. - Abstract: The solubility of limonin in the binary solvent mixtures (methanol + water) and (acetone + water) with various initial mole fractions of methanol or acetone was measured by high-performance liquid chromatography (HPLC) at different temperatures ranging from 283.2 K to 318.2 K. The solubility of limonin increased with increasing initial mole fraction of methanol in (methanol + water) mixtures, whereas it had a maximum point at 0.9 mol fraction of acetone in (acetone + water) mixtures. The solubility of limonin increased with increasing temperature in the two binary solvent mixtures. The solubility of limonin was correlated with temperature by the van’t Hoff model and the modified Apelblat model, and the fitting results showed that the modified Apelblat model had better correlation. The CNIBS/Redlich–Kister model and the simplified CNIBS/Redlich–Kister model were used to correlate the solubility data with the initial solvent composition, the results show that the CNIBS/Redlich–Kister model reveals better agreement with the experimental values. Furthermore, to illustrate the effects of both temperature and initial solvent composition on the changes in the solubility of limonin, the solubility values were fitted by the Jouyban–Acree, van’t Hoff–Jouyban–Acree, modified Apelblat–Jouyban–Acree, Ma and Sun models. Among the five models, the Jouyban–Acree model give the best correlation results for (methanol + water) binary solvent mixtures, while the experimental solubility in the (acetone + water) system was most accurately correlated by the van’t Hoff–Jouyban–Acree model.

High Resolution Multiphoton Ionization/Dissociation of Molecular Beam of Acetone from 582.60 to 585.80 nm

Science.gov (United States)

Mejia-Ospino, Enrique; Garcia, Gladis; Guerrero, Alfonso; Alvarez, Ignacio; Cisneros, Carmen

2003-05-01

Multiphoton ionization and dissociation of a jet supersonic of acetone at wavelength from 582.60 to 585.80 nm is studied using a Nd:YAG-OPO (optical parametric oscillator) system coupled to time-of-flight mass spectrometer. We present high-resolution (1.5 cm-1) three-photon resonance multiphoton spectra of the acetone 3s CH3CO+), (CH3+) and (COH+), being CH3COCH3+ ---> CH3CO+ + CH3 the more likely channel. The molecular and acetyl ions are observed practically in overall wavelength range.

Effects of Bronsted acidity in the mechanism of selective oxidation of propane to acetone on CaY zeolite at room temperature.

NARCIS (Netherlands)

Xu, J.; Mojet, Barbara; van Ommen, J.G.; Lefferts, Leonardus

2005-01-01

The importance of Brønsted acid sites for partial oxidation of propane to acetone in CaY was investigated by in situ FTIR spectroscopy. With an increasing number of protons in Ca-Y, Volcano plots were observed for (1) amount of adsorbed propane; (2) initial acetone formation rate; (3) total amount

Enhancement of Critical Current Density and Flux Pinning in Acetone and La2O3 Codoped MgB2 Tapes

International Nuclear Information System (INIS)

Gao Zhao-Shun; Ma Yan-Wei; Wang Dong-Liang; Zhang Xian-Ping; Awaji Satoshi; Watanabe Kazuo

2010-01-01

MgB 2 tape samples with simultaneous additions of acetone and La 2 O 3 were prepared by an in-situ processed powder-in-tube method. Compared to the pure and single doped tapes, both transport J c and fluxing pinning are greatly improved by acetone and La 2 O 3 codoping. Acetone supplies carbon into the MgB 2 crystal lattice and increases the upper critical field, while the La 2 O 3 reacts with B to form LaB 6 nanoparticles as effective flux pining centers. The improvement of the superconducting properties in codoped tapes can be attributed to the combined effects of improvement in H c2 and flux pinning. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Mutual diffusion of binary liquid mixtures containing methanol, ethanol, acetone, benzene, cyclohexane, toluene, and carbon tetrachloride

Energy Technology Data Exchange (ETDEWEB)

Guevara-Carrion, Gabriela; Janzen, Tatjana; Muñoz-Muñoz, Y. Mauricio; Vrabec, Jadran, E-mail: jadran.vrabec@uni-paderborn.de [Thermodynamics and Energy Technology, University of Paderborn, 33098 Paderborn (Germany)

2016-03-28

Mutual diffusion coefficients of all 20 binary liquid mixtures that can be formed out of methanol, ethanol, acetone, benzene, cyclohexane, toluene, and carbon tetrachloride without a miscibility gap are studied at ambient conditions of temperature and pressure in the entire composition range. The considered mixtures show a varying mixing behavior from almost ideal to strongly non-ideal. Predictive molecular dynamics simulations employing the Green-Kubo formalism are carried out. Radial distribution functions are analyzed to gain an understanding of the liquid structure influencing the diffusion processes. It is shown that cluster formation in mixtures containing one alcoholic component has a significant impact on the diffusion process. The estimation of the thermodynamic factor from experimental vapor-liquid equilibrium data is investigated, considering three excess Gibbs energy models, i.e., Wilson, NRTL, and UNIQUAC. It is found that the Wilson model yields the thermodynamic factor that best suits the simulation results for the prediction of the Fick diffusion coefficient. Four semi-empirical methods for the prediction of the self-diffusion coefficients and nine predictive equations for the Fick diffusion coefficient are assessed and it is found that methods based on local composition models are more reliable. Finally, the shear viscosity and thermal conductivity are predicted and in most cases favorably compared with experimental literature values.

Origin of Enhanced Reactivity of a Microsolvated Nucleophile in Ion Pair SN2 Reactions: The Cases of Sodium p-Nitrophenoxide with Halomethanes in Acetone.

Science.gov (United States)

Li, Qiang-Gen; Xu, Ke; Ren, Yi

2015-04-30

In a kinetic experiment on the SN2 reaction of sodium p-nitrophenoxide with iodomethane in acetone-water mixed solvent, Humeres et al. (J. Org. Chem. 2001, 66, 1163) found that the reaction depends strongly on the medium, and the fastest rate constant was observed in pure acetone. The present work tries to explore why acetone can enhance the reactivity of the title reactions. Accordingly, we make a mechanistic study on the reactions of sodium p-nitrophenoxide with halomethanes (CH3X, X = Cl, Br, I) in acetone by using a supramolecular/continuum model at the PCM-MP2/6-311+G(d,p)//B3LYP/6-311+G(d,p) level, in which the ion pair nucleophile is microsolvated by one to three acetone molecules. We compared the reactivity of the microsolvated ion pair nucleophiles with solvent-free ion pair and anionic ones. Our results clearly reveal that the microsolvated ion pair nucleophile is favorable for the SN2 reactions; meanwhile, the origin of the enhanced reactivity induced by microsolvation of the nucleophile is discussed in terms of the geometries of transition state (TS) structures and activation strain model, suggesting that lower deformation energies and stronger interaction energies between the deformed reactants in the TS lead to the lower overall reaction barriers for the SN2 reaction of microsolvated sodium p-nitrophenoxide toward halomethanes in acetone.

Dissociative electron attachment studies on acetone

Energy Technology Data Exchange (ETDEWEB)

Prabhudesai, Vaibhav S., E-mail: vaibhav@tifr.res.in; Tadsare, Vishvesh; Ghosh, Sanat; Gope, Krishnendu; Davis, Daly; Krishnakumar, E. [Tata Institute of Fundamental Research, Homi Bhabha Road, Colaba, Mumbai 400005 (India)

2014-10-28

Dissociative electron attachment (DEA) to acetone is studied in terms of the absolute cross section for various fragment channels in the electron energy range of 0–20 eV. H{sup −} is found to be the most dominant fragment followed by O{sup −} and OH{sup −} with only one resonance peak between 8 and 9 eV. The DEA dynamics is studied by measuring the angular distribution and kinetic energy distribution of fragment anions using Velocity Slice Imaging technique. The kinetic energy and angular distribution of H{sup −} and O{sup −} fragments suggest a many body break-up for the lone resonance observed. The ab initio calculations show that electron is captured in the multi-centered anti-bonding molecular orbital which would lead to a many body break-up of the resonance.

Multi-species time-history measurements during high-temperature acetone and 2-butanone pyrolysis

KAUST Repository

Lam, Kingyiu

2013-01-01

High-temperature acetone and 2-butanone pyrolysis studies were conducted behind reflected shock waves using five species time-history measurements (ketone, CO, CH3, CH4 and C2H4). Experimental conditions covered temperatures of 1100-1600 Kat 1.6 atm, for mixtures of 0.25-1.5% ketone in argon. During acetone pyrolysis, the CO concentration time-history was found to be strongly sensitive to the acetone dissociation rate constant κ1 (CH3COCH3 → CH3 + CH3CO), and this could be directly determined from the CO time-histories, yielding κ1(1.6 atm) = 2.46 × 1014 exp(-69.3 [kcal/mol]/RT) s-1 with an uncertainty of ±25%. This rate constant is in good agreement with previous shock tube studies from Sato and Hidaka (2000) [3] and Saxena et al. (2009) [4] (within 30%) at temperatures above 1450 K, but is at least three times faster than the evaluation from Sato and Hidaka at temperatures below 1250 K. Using this revised κ1 value with the recent mechanism of Pichon et al. (2009) [5], the simulated profiles during acetone pyrolysis show excellent agreement with all five species time-history measurements. Similarly, the overall 2-butanone decomposition rate constant κtot was inferred from measured 2-butanone time-histories, yielding κ tot(1.5 atm) = 6.08 × 1013 exp(-63.1 [kcal/mol]/RT) s -1 with an uncertainty of ±35%. This rate constant is approximately 30% faster than that proposed by Serinyel et al. (2010) [11] at 1119 K, and approximately 100% faster at 1412 K. Using the measured 2-butanone and CO time-histories and an O-atom balance analysis, a missing removal pathway for methyl ketene was identified. The rate constant for the decomposition of methyl ketene was assumed to be the same as the value for the ketene decomposition reaction. Using the revised κtot value and adding the methyl ketene decomposition reaction to the Serinyel et al. mechanism, the simulated profiles during 2-butanone pyrolysis show good agreement with the measurements for all five species. �

Multi-species time-history measurements during high-temperature acetone and 2-butanone pyrolysis

KAUST Repository

Lam, Kingyiu; Ren, Wei; Pyun, Sunghyun; Farooq, Aamir; Davidson, David Frank; Hanson, Ronald Kenneth

2013-01-01

High-temperature acetone and 2-butanone pyrolysis studies were conducted behind reflected shock waves using five species time-history measurements (ketone, CO, CH3, CH4 and C2H4). Experimental conditions covered temperatures of 1100-1600 Kat 1.6 atm

Enhanced robustness in acetone-butanol-ethanol fermentation with engineered Clostridium beijerinckii overexpressing adhE2 and ctfAB.

Science.gov (United States)

Lu, Congcong; Yu, Le; Varghese, Saju; Yu, Mingrui; Yang, Shang-Tian

2017-11-01

Clostridium beijerinckii CC101 was engineered to overexpress aldehyde/alcohol dehydrogenase (adhE2) and CoA-transferase (ctfAB). Solvent production and acid assimilation were compared between the parental and engineered strains expressing only adhE2 (CC101-SV4) and expressing adhE2, ald and ctfAB (CC101-SV6). CC101-SV4 showed an early butanol production from glucose but stopped pre-maturely at a low butanol concentration of ∼6g/L. Compared to CC101, CC101-SV6 produced more butanol (∼12g/L) from glucose and was able to re-assimilate more acids, which prevented "acid crash" and increased butanol production, under all conditions studied. CC101-SV6 also showed better ability in using glucose and xylose present in sugarcane bagasse hydrolysate, and produced 9.4g/L solvents (acetone, butanol and ethanol) compared to only 2.6g/L by CC101, confirming its robustness and better tolerance to hydrolysate inhibitors. The engineered strain of C. beijerinckii overexpressing adhE2 and ctfAB should have good potential for producing butanol from lignocellulosic biomass hydrolysates. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of using acetone and distilled water on the performance of open loop pulsating heat pipe (OLPHP) with different filling ratios

Science.gov (United States)

Rahman, Md. Lutfor; Afrose, Tonima; Tahmina, Halima Khatun; Rinky, Rumana Parvin; Ali, Mohammad

2016-07-01

Pulsating heat pipe (PHP) is a new innovation in the modern era of miniaturizes thermal management system for its higher heating and cooling capacity. The objective of this experiment is to observe the performance of open loop pulsating heat pipe using two fluids at different filling ratios. This OLPHP is a copper capillary tube of 2.5mm outer diameter and 2mm inner diameter. It consists of 8 loops where the evaporative section is 50mm, adiabatic section is 120mm and condensation section is 80mm. The experiment is conducted with distilled water and acetone at 40%, 50%, 60%, and 70% filling ratios where 0° (vertical) is considered as definite angle of inclination. Distilled water and acetone are selected as working fluids considering their different latent heat of vaporization and surface tension. It is found that acetone shows lower thermal resistance than water at all heat inputs. Best performance of acetone is attained at 70% filling ratio. Water displays better heat transfer capability at 50% filling ratio.

Technical and economic assessment of processes for the production of butanol and acetone

Science.gov (United States)

1982-01-01

This report represents a preliminary technical and economic evaluation of a process which produces mixed solvents (butaol/acetone/ethanol) via fermentation of sugars derived from renewable biomass resources. The objective is to assess the technology of producing butanol/acetone from biomass, and select a viable process capable of serving as a base case model for technical and economic analysis. It is anticipated that the base case process developed herein can then be used as the basis for subsequent studies concerning biomass conversion processes capable of producing a wide range of chemicals. The general criteria utilized in determining the design basis for the process are profit potential and non-renewable energy displacement potential. The feedstock chosen, aspen wood, was selected from a number of potential renewable biomass resources as the most readily available in the United States and for its relatively large potential for producing reducing sugars.

Uptake of acetone, ethanol and benzene to snow and ice: effects of surface area and temperature

International Nuclear Information System (INIS)

Abbatt, J P D; Bartels-Rausch, T; Ullerstam, M; Ye, T J

2008-01-01

The interactions of gas-phase acetone, ethanol and benzene with smooth ice films and artificial snow have been studied. In one technique, the snow is packed into a cylindrical column and inserted into a low-pressure flow reactor coupled to a chemical-ionization mass spectrometer for gas-phase analysis. At 214 and 228 K, it is found for acetone and ethanol that the adsorbed amounts per surface area match those for adsorption to thin films of ice formed by freezing liquid water, when the specific surface area of the snow (as determined from Kr adsorption at 77 K) and the geometric surface area of the ice films are used. This indicates that freezing thin films of water leads to surfaces that are smooth at the molecular level. Experiments performed to test the effect of film growth on ethanol uptake indicate that uptake is independent of ice growth rate, up to 2.4 μm min -1 . In addition, traditional Brunauer-Emmett-Teller (BET) experiments were performed with these gases on artificial snow from 238 to 266.5 K. A transition from a BET type I isotherm indicative of monolayer formation to a BET type II isotherm indicative of multilayer uptake is observed for acetone at T≥263 K and ethanol at T≥255 K, arising from solution formation on the ice. When multilayer formation does not occur, as was the case for benzene at T≤263 K and for acetone at T≤255 K, the saturated surface coverage increased with increasing temperature, consistent with the quasi-liquid layer affecting adsorption prior to full dissolution/multilayer formation.

Experimental study on liver accumulation of N-isopropyl-p-iodoamphetamine

Energy Technology Data Exchange (ETDEWEB)

Kosuda, Shigeru (Tokyo Metropolitan Komagome Hospital (Japan)); Kawahara, Shunji; Ishibashi, Akihiko; Tamura, Kohei; Kubo, Atsushi; Hashimoto, Shozo

1990-06-01

In order to clarify the mechanism of N-isopropyl-p-iodoamphetamine (IMP) liver accumulation, liver dynamic study by the portal injection of {sup 123}I-IMP and liver microautoradiography by {sup 125}I-IMP were performed using 5, 2 male rats, respectively. The initial uptake of {sup 123}I-IMP in the liver was very high and thereafter {sup 123}I-IMP showed relatively rapid wash-out (count ratio of lung to liver at 10 min after the injection was 0.12, 0.15). On the other hand, the addition of 5 mg, 8 mg ketamine hydrochloride decreased the initial {sup 123}I-IMP liver uptake and its lung accumulation was noted immediately after the injection (count ratio of lung to liver at 10 min was 0.20). Microautoradiography of the liver using {sup 125}I-IMP showed grain density in the central vein and sinusoids, but not in the liver parenchymal cell. These results suggest that non-specific amine receptor (binding site) may exist in the endothelial cell in the central vein, although the number of experimental rats in this series was small for conclusion. (author).

Acetone-water complexes at MRCI level using localized orbitals: n ->pi* and pi ->pi* electronic transitions

DEFF Research Database (Denmark)

Hoyau, S.; Ben Amor, N.; Borini, Stefano

2008-01-01

The n -> pi* and pi -> pi* vertical electronic transitions of acetone with two and four H2O which correspond to a first solvation shell are considered. By using localized orbitals, and thanks to the MRCI approach which permits to know the wave function, the role of the various solvent molecules...... is analysed in details. Distinguishing the solvent molecules allows one to consider them at different calculation levels. The methodology is to compare the spectra obtained with four H2O, with two H2O either in the acetone plane or in a perpendicular plane and when they are completely or partly frozen....

Measurement of endogenous acetone and isoprene in exhaled breath during sleep

International Nuclear Information System (INIS)

King, Julian; Kupferthaler, Alexander; Unterkofler, Karl; Amann, Anton; Frauscher, Birgit; Hackner, Heinz; Högl, Birgit; Teschl, Gerald; Hinterhuber, Hartmann

2012-01-01

This explorative study aims at characterizing the breath behavior of two prototypic volatile organic compounds, acetone and isoprene, during normal human sleep and to possibly relate changes in the respective concentration time courses to the underlying sleep architecture. For this purpose, six normal healthy volunteers (two females, four males, age 20–29 years) were monitored over two consecutive nights (the first one being an adaption night) by combining real-time proton-transfer-reaction mass spectrometry measurements from end-tidal exhalation segments with laboratory-based polysomnographic data. Breath acetone concentrations increased overnight in all measurements, with an average relative change by a factor of up to 4 (median 2.5). Nighttime concentration maxima were usually recorded 2–3 h before lights on. For breath isoprene, a nocturnal increase in baseline concentrations of about 74% was observed, with individual changes ranging from 36–110%. Isoprene profiles exhibited pronounced concentration peaks, which were highly specific for leg movements as scored by tibial electromyography. Furthermore, relative to a linear trend, baseline isoprene concentrations decreased during the transition from the NREM to the REM phase of a complete sleep cycle. (paper)

1-Butyl-3-Methylimidazolium Tetrafluoroborate Film as a Highly Selective Sensing Material for Non-Invasive Detection of Acetone Using a Quartz Crystal Microbalance.

Science.gov (United States)

Tao, Wenyan; Lin, Peng; Liu, Sili; Xie, Qingji; Ke, Shanming; Zeng, Xierong

2017-01-20

Breath acetone serves as a biomarker for diabetes. This article reports 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]), a type of room temperature ionic liquid (RTIL), as a selective sensing material for acetone. The RTIL sensing layer was coated on a quartz crystal microbalance (QCM) for detection. The sensing mechanism is based on a decrease in viscosity and density of the [bmim][BF₄] film due to the solubilization of acetone leading to a positive frequency shift in the QCM. Acetone was detected with a linear range from 7.05 to 750 ppmv. Sensitivity and limit of detection were found to be 3.49 Hz/ppmv and 5.0 ppmv, respectively. The [bmim][BF₄]-modified QCM sensor demonstrated anti-interference ability to commonly found volatile organic compounds in breath, e.g., isoprene, 1,2-pentadiene, d -limonene, and dl -limonene. This technology is useful for applications in non-invasive early diabetic diagnosis.

Preparation of Peleted Ni-Pt/Zeolite for Conversion of Amyl and Isoamyl Alcohol to Hydrocarbon

Directory of Open Access Journals (Sweden)

Abdullah Abdullah

2010-06-01

Full Text Available Catalysts with Ni and Pt as active metals in peleted zeolite were used for conversion of amyl alcohol, isoamyl alcohol and their mixture to hydrocarbon compounds. The catalysts were prepared by impregnation the peleted zeolite in NiCl2.6H2O and PtCI4 solution, while stirring for 24 hours then followed by oxidation with 02 gas at 350 °C for 2 hours and reduced by hydrogen gas at 400 °C for 1 hour. Ni and Pt in catalysts were determined by MS, specific surface area, total pore volume and gas sorption analyzer NOVA-1000 determined pore radius average. Determination of catalysts acidity was carried out by absorption of ammonia method. The activity of catalysts was evaluated in a micro reactor by flow system. Experimental temperature by varied between 300 and 400 °C with the increment of 25 °C. Products were analyzed by gas chromatographic and mass spectrometric method. The result shows that Ni-Pt/zeolite is more active than Ni/zeolite can be used for converting all of the alcohol. Products for conversion are 2-pentene, 2-methyl-1-butene, 2-methyl-2-butene, cyclopentane, 3-methyl-1-butanaldehide and acetone. The highest conversion was observed on isoamyl alcohol (31.37% at 400 °C.

Synthesis of Cu/TiO{sub 2}/organo-attapulgite fiber nanocomposite and its photocatalytic activity for degradation of acetone in air

Energy Technology Data Exchange (ETDEWEB)

Zhang, Gaoke, E-mail: gkzhang@whut.edu.cn; Wang, He; Guo, Sheng; Wang, Junting; Liu, Jin

2016-01-30

Graphical abstract: - Highlights: • A novel Cu/TiO{sub 2}/organo-attapulgite fiber nanocomposite was synthesized successfully. • Micro-mesopore nanocomposite structure was in favor of the degradation of acetone. • CTAB modification improved the adsorption capability of the catalyst. • The photocatalytic degradation mechanism of the acetone by the catalyst was studied. - Abstract: The Cu/TiO{sub 2}/organo-attapulgite fiber (CTOA) nanocomposite was synthesized by a facile method and was used for photocatalytic degradation of acetone in air under UV light irradiation. The as-prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscope (SEM), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectrum (UV–vis DRS), inductively coupled plasma (ICP) spectrometry and N{sub 2} adsorption–desorption measurement. The results showed that the structure of organo-attapulgite (OAT) had no obvious change as compared to unmodified attapulgite (AT) and the attapulgite fibers in the OAT were well-dispersed. Both micropores and mesopores exist in the CTOA catalyst. The CTOA catalysts prepared at the Cu/TiO{sub 2} molar ratio of 0.003 shows an excellent photocatalytic activity for the degradation of acetone in air. The synergistic effect of Cu species and cetyltrimethylammonium bromide modification can be responsible for the enhanced photocatalytic activity of the CTOA catalyst. The mechanism of the photocatalytic degradation of acetone by the CTOA catalyst was discussed.

Butanol-acetone fermentation of sugar-cane juice

Energy Technology Data Exchange (ETDEWEB)

Perdomo, E V

1958-01-01

Sixteen new varieties of Clostridium acetobutylicum of varying activity were isolated from different sources. The most active one was obtained from sugar-cane roots. The effects of 86 additives were studied. The following formulation gave a 32% yield (with respect to sucrose) of solvent mixture (73% BuOH, 19 to 23% acetone, and 3 to 4% EtOH) sugar-cane juice (I) (20/sup 0/ Brix) 250 ml, ground Vicia sativa 1 g, KH/sub 2/PO/sub 4/ 2.5 g, CaCO/sub 3/ 4 g, H/sub 2/O 1000 ml; the pH of this solution was 5.6 to 6.0. Unclarified, it was inverted by invertase; the other components were added and the mixture was sterilized (20 minutes, 15 pounds).

Comparison of Four Antiseptic Preparations for Skin in the Prevention of Contamination of Percutaneously Drawn Blood Cultures: a Randomized Trial

Science.gov (United States)

Calfee, David P.; Farr, Barry M.

2002-01-01

A number of skin antiseptics have been used to prevent the contamination of blood cultures, but the comparative efficacies of these agents have not been extensively evaluated. We therefore sought to compare the efficacy of four skin antiseptics in preventing blood culture contamination in a randomized, crossover, investigator-blinded study conducted in an emergency department and the inpatient wards of a university hospital. The patient group included all patients from whom blood samples were obtained percutaneously for culture. Skin antisepsis was performed with 10% povidone-iodine, 70% isopropyl alcohol, tincture of iodine, or povidone-iodine with 70% ethyl alcohol (i.e., Persist). The blood culture contamination rate associated with each antiseptic was then determined. A total of 333 (2.62%) of 12,692 blood cultures were contaminated during the study period compared to 413 (3.21%) of 12,859 blood cultures obtained during the previous 12-month period (relative risk = 0.82; 95% confidence interval, 0.71 to 0.94; P = 0.006). During the study, the contamination rates were determined to be 2.93% with povidone-iodine, 2.58% with tincture of iodine, 2.50% with isopropyl alcohol, and 2.46% with Persist (P = 0.62). We detected no significant differences in the blood culture contamination rates among these four antiseptics, although there was some evidence suggesting greater efficacy among the alcohol-containing antiseptics. Among the evaluated antiseptics, isopropyl alcohol may be the optimal antiseptic for use prior to obtaining blood for culture, given its convenience, low cost, and tolerability. PMID:11980938

Study on the Alkylation Reactions of N(7)-Unsubstituted 1,3-Diazaoxindoles.

Science.gov (United States)

Kókai, Eszter; Halász, Judit; Dancsó, András; Nagy, József; Simig, Gyula; Volk, Balázs

2017-05-19

The chemistry of the 5,7-dihydro-6 H -pyrrolo[2,3- d ]pyrimidin-6-one (1,3-diazaoxindole) compound family, possessing a drug-like scaffold, is unexplored. In this study, the alkylation reactions of N (7)-unsubstituted 5-isopropyl-1,3-diazaoxindoles bearing various substituents at the C (2) position have been investigated. The starting compounds were synthesized from the C (5)-unsubstituted parent compounds by condensation with acetone and subsequent catalytic reduction of the 5-isopropylidene moiety. Alkylation of the thus obtained 5-isopropyl derivatives with methyl iodide or benzyl bromide in the presence of a large excess of sodium hydroxide led to 5,7-disubstituted derivatives. Use of butyllithium as the base rendered alkylation in the C (5) position possible with reasonable selectivity, without affecting the N (7) atom. During the study on the alkylation reactions, some interesting by-products were also isolated and characterized.

The origin of star-shaped oscillations of Leidenfrost drops

Science.gov (United States)

Ma, Xiaolei; Burton, Justin C.

We experimentally investigate the oscillations of Leidenfrost drops of water, liquid nitrogen, ethanol, methanol, acetone and isopropyl alcohol. The drops levitate on a cushion of evaporated vapor over a hot, curved surface which keeps the drops stationary. We observe star-shaped modes along the periphery of the drop, with mode numbers n = 2 to 13. The number of observed modes is sensitive to the properties of the liquid. The pressure oscillation frequency in the vapor layer under the drop is approximately twice that of the drop frequency, which is consistent with a parametric forcing mechanism. However, the Rayleigh and thermal Marangoni numbers are of order 10,000, indicating that convection should play a dominating role as well. Surprisingly, we find that the wavelength and frequency of the oscillations only depend on the thickness of the liquid, which is twice the capillary length, and do not depend on the mode number, substrate temperature, or the substrate curvature. This robust behavior suggests that the wavelength for the oscillations is set by thermal convection inside the drop, and is less dependent on the flow in the vapor layer under the drop

Affecting the morphology of silver deposition on carbon nanotube surface: From nanoparticles to dendritic (tree-like) nanostructures

Energy Technology Data Exchange (ETDEWEB)

Forati-Nezhad, Mohsen [Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Mir Mohamad Sadeghi, Gity, E-mail: gsadeghi@aut.ac.ir [Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Yaghmaie, Frank [Northern California Nanotechnology Center, University of California, Davis, CA 95616 (United States); Alimohammadi, Farbod [Young Researchers and Elite Club, South Tehran Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of)

2015-01-01

Chemical reduction was used to synthesize silver crystals on the surface of multiwall carbon nanotubes (MWCNTs) in the presence of acetone, N,N-dimethylformamide (DMF), N-methyl-2-pyrrolidone, and isopropyl alcohol as solvent. DMF and sodium dodecyl sulfate were used as a reducing and a stabilizing agent, respectively. The structure and nature of hybrid MWCNT/silver were characterized by Raman spectroscopy, FTIR spectroscopy, transmission electron microscopy (TEM), and field emission scanning electron microscope (FESEM). The presence of silver crystals on the nanotubes was confirmed by XRD. The results show the formation of silver crystals on the MWCNT surface and indicate that the morphology of silver crystals can be control by changing the solvent. The type of solvent is an effective parameter that affects the particle size and morphological transition from nanoparticles to silver trees. - Highlights: • The silver crystals are grown on the CNT surface by chemical reduction method. • The morphology of silver crystals is controlled by changing the solvent. • Silver nanoparticles and dendritic nanostructures on CNT surface are achieved. • Any change in structure and surface defects by synthesis condition is investigated.

N-isopropyl I-123 p-iodoamphetamine (IMP) brain SPECT in dementia

International Nuclear Information System (INIS)

Momose, Toshimitsu; Kosaka, Noboru; Nishikawa, Junichi; Yoshikawa, Kohki; Ohtake, Tohru; Watanabe, Toshiaki; Iwata, Makoto; Shimizu, Teruo; Iio, Masahiro

1988-01-01

Six patients of Alzheimer's disease (AD), two patients of Pick disease (PD) and two patients of Creutzfeldt-Jakob disease (CJD) were studied with N-Isopropyl I-123 p-Iodoamphetamine (IMP) with SPECT. The pattern of IMP uptake in these demented groups were compared with that in five agematched normal controls and correlated with MRI and XCT. In all AD cases, SPECT revealed focal reduction of IMP uptake in frontal (6/6), parietal (6/6) and temporal (6/6) cortex, although MRI and XCT were normal. In both PD case, SPECT showed focal reduction of IMP uptake in frontal (1/2) and temporal (2/2) cortex with moderate labor atrophy on MRI and XCT. In both CJD case, SPECT showed diffuse reduction of IMP uptake in cerebral cortex in spite of no abnormality on MRI and XCT. These findings suggest that SPECT can detect earlier diseased process of AD and CJD than MRI or XCT and that SPECT may be helpful for the differential diagnosis of non-vascular dementia. (author)

N-isopropyl I-123 p-iodoamphetamine (IMP) brain SPECT in dementia

Energy Technology Data Exchange (ETDEWEB)

Momose, Toshimitsu; Kosaka, Noboru; Nishikawa, Junichi; Yoshikawa, Kohki; Ohtake, Tohru; Watanabe, Toshiaki; Iwata, Makoto; Shimizu, Teruo; Iio, Masahiro

1988-12-01

Six patients of Alzheimer's disease (AD), two patients of Pick disease (PD) and two patients of Creutzfeldt-Jakob disease (CJD) were studied with N-Isopropyl I-123 p-Iodoamphetamine (IMP) with SPECT. The pattern of IMP uptake in these demented groups were compared with that in five agematched normal controls and correlated with MRI and XCT. In all AD cases, SPECT revealed focal reduction of IMP uptake in frontal (6/6), parietal (6/6) and temporal (6/6) cortex, although MRI and XCT were normal. In both PD case, SPECT showed focal reduction of IMP uptake in frontal (1/2) and temporal (2/2) cortex with moderate labor atrophy on MRI and XCT. In both CJD case, SPECT showed diffuse reduction of IMP uptake in cerebral cortex in spite of no abnormality on MRI and XCT. These findings suggest that SPECT can detect earlier diseased process of AD and CJD than MRI or XCT and that SPECT may be helpful for the differential diagnosis of non-vascular dementia.

Study of continuous acetone-butanol fermentation by Clostridium acetobutylicum

Energy Technology Data Exchange (ETDEWEB)

Yarovenko, V L; Nakhmanovich, B M; Shcheblykin, N P; Senkevich, V V

1960-01-01

Prophylactic sterilization of small scale equipment (2 fermenters, 3.5 cu. m. each) permitted continuous fermentation through 6 cycles (28 days), each with a new inoculum of C. acetobutylicum. Single cycles could be prolonged to 6 to 11 days without sterilization. Contamination, usually with lactic acid bacteria, sometimes preceded exhaustion of the culture. Input of flour mash at 0.6 to 1.2 cu. m./hr. and withdrawal of products were continuous; acetone yield 6.6 to 7.1 g./l.; residual sugars 0.63 to 0.79%.

2D Sn-doped ZnO ultrathin nanosheet networks for enhanced acetone gas sensing application

KAUST Repository

Al-Hadeethi, Yas; Umar, Ahmad; Al-Heniti, Saleh. H.; Kumar, Rajesh; Kim, S.H.; Zhang, Xixiang; Raffah, Bahaaudin M.

2016-01-01

In this paper, we report the synthesis, characterizations and gas sensing application of 2D Sn-doped ZnO ultrathin nanosheet networks synthesized by a simple and facile hydrothermal process. The synthesized nanosheets were characterized using several techniques in terms of their morphological, structural, optical and compositional properties. The detailed characterizations confirmed that the nanosheets are pure, grown in high-density, possessing well-crystalline wurtzite hexagonal phase and exhibiting good optical properties. Further, the synthesized nanosheets were used as functional material to develop nanosensor device by coating it on the alumina substrate with suitable electrodes. The fabricated sensor device was tested towards acetone gas which exhibited a maximum sensitivity of 5.556 (Ra/Rg) for 200 ppm of acetone at 320 °C.

2D Sn-doped ZnO ultrathin nanosheet networks for enhanced acetone gas sensing application

KAUST Repository

Al-Hadeethi, Yas

2016-11-10

In this paper, we report the synthesis, characterizations and gas sensing application of 2D Sn-doped ZnO ultrathin nanosheet networks synthesized by a simple and facile hydrothermal process. The synthesized nanosheets were characterized using several techniques in terms of their morphological, structural, optical and compositional properties. The detailed characterizations confirmed that the nanosheets are pure, grown in high-density, possessing well-crystalline wurtzite hexagonal phase and exhibiting good optical properties. Further, the synthesized nanosheets were used as functional material to develop nanosensor device by coating it on the alumina substrate with suitable electrodes. The fabricated sensor device was tested towards acetone gas which exhibited a maximum sensitivity of 5.556 (Ra/Rg) for 200 ppm of acetone at 320 °C.

A Comparison Study: The New Extended Shelf Life Isopropyl Ester PMR Technology versus The Traditional Methyl Ester PMR Approach

Science.gov (United States)

Alston, William B.; Scheiman, Daniel A.; Sivko, Gloria S.

2005-01-01

Polymerization of Monomeric Reactants (PMR) monomer solutions and carbon cloth prepregs of PMR II-50 and VCAP-75 were prepared using both the traditional limited shelf life methanol based PMR approach and a novel extended shelf life isopropanol based PMR approach. The methyl ester and isopropyl ester based PMR monomer solutions and PMR prepregs were aged for up to four years at freezer and room temperatures. The aging products formed were monitored using high pressure liquid chromatography (HPLC). The composite processing flow characteristics and volatile contents of the aged prepregs were also correlated versus room temperature storage time. Composite processing cycles were developed and six ply cloth laminates were fabricated with prepregs after various extended room temperature storage times. The composites were then evaluated for glass transition temperature (Tg), thermal decomposition temperature (Td), initial flexural strength (FS) and modulus (FM), long term (1000 hours at 316 C) thermal oxidative stability (TOS), and retention of FS and FM after 1000 hours aging at 316 C. The results for each ester system were comparable. Freezer storage was found to prevent the formation of aging products for both ester systems. Room temperature storage of the novel isopropyl ester system increased PMR monomer solution and PMR prepreg shelf life by at least an order of magnitude while maintaining composite properties.

Applications of Laser Diagnostics

Science.gov (United States)

2005-03-01

fraction of methane in the fuel is 0.48. The steady nozzle velocities of the fuel and oxyder stream are respectively 0.59 m/s and 0.61 m/s. The...Hexane Heptane Toluene Benzene THF Ethyl acetate Chloroform Dichloromethane Acetone DMSO Propylene carbonate Benzyl alcohol Ethanol Methanol Octanol...Cyclohexane Pentane Hexane Heptane Toluene Benzene THF Ethyl acetate Chloroform Dichloromethane Acetone DMSO Propylene carbonate Benzyl alcohol Ethanol

An Optimized Trichloroacetic Acid/Acetone Precipitation Method for Two-Dimensional Gel Electrophoresis Analysis of Qinchuan Cattle Longissimus Dorsi Muscle Containing High Proportion of Marbling.

Science.gov (United States)

Hao, Ruijie; Adoligbe, Camus; Jiang, Bijie; Zhao, Xianlin; Gui, Linsheng; Qu, Kaixing; Wu, Sen; Zan, Linsen

2015-01-01

Longissimus dorsi muscle (LD) proteomics provides a novel opportunity to reveal the molecular mechanism behind intramuscular fat deposition. Unfortunately, the vast amounts of lipids and nucleic acids in this tissue hampered LD proteomics analysis. Trichloroacetic acid (TCA)/acetone precipitation is a widely used method to remove contaminants from protein samples. However, the high speed centrifugation employed in this method produces hard precipitates, which restrict contaminant elimination and protein re-dissolution. To address the problem, the centrifugation precipitates were first grinded with a glass tissue grinder and then washed with 90% acetone (TCA/acetone-G-W) in the present study. According to our result, the treatment for solid precipitate facilitated non-protein contaminant removal and protein re-dissolution, ultimately improving two-dimensional gel electrophoresis (2-DE) analysis. Additionally, we also evaluated the effect of sample drying on 2-DE profile as well as protein yield. It was found that 30 min air-drying did not result in significant protein loss, but reduced horizontal streaking and smearing on 2-DE gel compared to 10 min. In summary, we developed an optimized TCA/acetone precipitation method for protein extraction of LD, in which the modifications improved the effectiveness of TCA/acetone method.

Ramalina capitata (Ach.) Nyl. acetone extract: HPLC analysis, genotoxicity, cholinesterase, antioxidant and antibacterial activity.

Science.gov (United States)

Zrnzevic, Ivana; Stankovic, Miroslava; Stankov Jovanovic, Vesna; Mitic, Violeta; Dordevic, Aleksandra; Zlatanovic, Ivana; Stojanovic, Gordana

2017-01-01

In the present investigation, effects of Ramalina capitata acetone extract on micronucleus distribution on human lymphocytes, on cholinesterase activity and antioxidant activity (by the CUPRAC method) were examined, for the first time as well as its HPLC profile. Additionally, total phenolic compounds (TPC), antioxidant properties (estimated via DPPH, ABTS and TRP assays) and antibacterial activity were determined. The predominant phenolic compounds in this extract were evernic, everninic and obtusatic acids. Acetone extract of R. capitata at concentration of 2 μg mL -1 decreased a frequency of micronuclei (MN) for 14.8 %. The extract reduces the concentration of DPPH and ABTS radicals for 21.2 and 36.1 % (respectively). Values for total reducing power (TRP) and cupric reducing capacity (CUPRAC) were 0.4624 ± 0.1064 μg ascorbic acid equivalents (AAE) per mg of dry extract, and 6.1176 ± 0.2964 μg Trolox equivalents (TE) per mg of dry extract, respectively. The total phenol content was 670.6376 ± 66.554 μg galic acid equivalents (GAE) per mg of dry extract. Tested extract at concentration of 2 mg mL -1 exhibited inhibition effect (5.2 %) on pooled human serum cholinesterase. The antimicrobial assay showed that acetone extract had inhibition effect towards Gram-positive strains. The results of manifested antioxidant activity, reducing the number of micronuclei in human lymphocytes, and antibacterial activity recommends R. capitata extract for further in vivo studies.

N-isopropyl-p-[123I]iodoamphetamine SPECT in MELAS syndrome: Comparison with CT and MR imaging

International Nuclear Information System (INIS)

Satoh, M.; Ishikawa, N.; Yoshizawa, T.; Takeda, T.; Akisada, M.

1991-01-01

Regional cerebral perfusion was studied in three patients with the mitochondrial encephalomyopathy with lactic acidosis and stroke-like episodes (MELAS) syndrome, using single photon emission computed tomography (SPECT) with N-isopropyl-p-[123I]iodoamphetamine (IMP). Accumulation of the tracer was relatively decreased in the parietooccipital regions and also in the frontotemporal regions after stroke-like episodes. However, quantitative regional cerebral blood flow (rCBF) measurement showed that rCBF was relatively well preserved even at these sites, and a hyperemic state was observed at the sites of normal accumulation. IMP SPECT may be useful in the diagnosis and assessment of the progress of the MELAS syndrome

Raman study of pressure effects on frequencies and isotropic line shapes in liquid acetone

International Nuclear Information System (INIS)

Schindler, W.; Sharko, P.T.; Jonas, J.

1982-01-01

The Raman line shape of the symmetric C = O stretching band at 1710 cm -1 has been measured in liquid acetone as a function of pressure from 1 bar to 4 kbar over the temperature range from -25 to 50 0 C. The experimental data obtained show several unusual features. First, there is a frequency difference of about 7 cm -1 between the polarized and depolarized components. Sceond, the isotropic linewidth GAMMA/sub iso/ decreases with increasing density, in contrast to the opposite trend usually found in other liquids. Third, the second moment M 2 (V) of the isotropic band appears to decrease with increasing density. The consideration of the experimental linewidth and frequency data leads to a conclusion that intermolecular dipole--dipole coupling between polar acetone molecules are responsible for the observed unusual behavior of , GAMMA/sub iso/, and M 2

1-Butyl-3-Methylimidazolium Tetrafluoroborate Film as a Highly Selective Sensing Material for Non-Invasive Detection of Acetone Using a Quartz Crystal Microbalance

Directory of Open Access Journals (Sweden)

Wenyan Tao

2017-01-01

Full Text Available Breath acetone serves as a biomarker for diabetes. This article reports 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4], a type of room temperature ionic liquid (RTIL, as a selective sensing material for acetone. The RTIL sensing layer was coated on a quartz crystal microbalance (QCM for detection. The sensing mechanism is based on a decrease in viscosity and density of the [bmim][BF4] film due to the solubilization of acetone leading to a positive frequency shift in the QCM. Acetone was detected with a linear range from 7.05 to 750 ppmv. Sensitivity and limit of detection were found to be 3.49 Hz/ppmv and 5.0 ppmv, respectively. The [bmim][BF4]-modified QCM sensor demonstrated anti-interference ability to commonly found volatile organic compounds in breath, e.g., isoprene, 1,2-pentadiene, d-limonene, and dl-limonene. This technology is useful for applications in non-invasive early diabetic diagnosis.

Silica functionalized Cu(II) acetylacetonate Schiff base complex: An efficient catalyst for the oxidative condensation reaction of benzyl alcohol with amines

Science.gov (United States)

Anbarasu, G.; Malathy, M.; Karthikeyan, P.; Rajavel, R.

2017-09-01

Silica functionalized Cu(II) acetylacetonate Schiff base complex via the one pot reaction of silica functionalized 3-aminopropyltriethoxysilane with acetyl acetone and copper acetate has been reported. The synthesized material was well characterized by analytical techniques such as FT-IR, UV-DRS, XRD, SEM-EDX, HR-TEM, EPR, ICP-AES and BET analysis. The characterization results confirmed the grafting of Cu(II) Schiff base complex on the silica surface. The catalytic activity of synthesized silica functionalized Cu(II) acetylacetonate Schiff base complex was evaluated through the oxidative condensation reaction of benzyl alcohol to imine.

Influence of concentration of sucrose on the acetone-butanol fermentation by different strains of Clostridium

Energy Technology Data Exchange (ETDEWEB)

Bahadue, K; Saroj, K K

1959-01-01

To culture media containing (NH/sub 4/)/sub 2/SO/sub 4/ (0.34 g) and MgSO/sub 4/ (0.16 g), were added 5, 10, and 20% sucrose, respectively; the pH was adjusted to 6.4 with KH/sub 2/PO/sub 4/-NaOH buffer; the volume of each medium was made up to 200 ml. The media were sterilized. After cooling, the media at the 5, 10, 20% sucrose levels were inoculated separately with C. butyricum, C. butyricum 6084, C. acetobutylicum NRRL B-527, C. pasteurianum NRRL B-598, C. butylicus NRRL B-592, and C. pasteurianum ATCC 6013. The cultures were incubated for 20 days at 35 degrees. For maximum butanol yield the 5% sucrose level was optimum for all the strains tested. At the 10% sucrose level great increase in sugar consumption occurred with C. butyricum Frolund, C. pasteurianum ATCC-6013, and C. butylicus IAL 15-152. Twice as much sucrose was consumed with C. acetobutylicum ATCC 6013, and NRRL B-572, and C. pasteurianum NRRL B-598. The increased sucrose consumption did not result in increased production of butanol or acetone. No acetone or butanol was formed with C. butyricum Frolund when the sucrose concentration was increased from 5 to 10%. With the increase in sucrose concentration, the formation of butanol and acetone decreased; acid formation was also inhibited.

Nesterenkonia sp. strain F, a halophilic bacterium producing acetone, butanol, and ethanol under aerobic conditions.

Science.gov (United States)

Amiri, Hamid; Azarbaijani, Reza; Parsa Yeganeh, Laleh; Shahzadeh Fazeli, Abolhassan; Tabatabaei, Meisam; Salekdeh, Ghasem Hosseini; Karimi, Keikhosro

2016-01-04

The moderately halophilic bacterium Nesterenkonia sp. strain F, which was isolated from Aran-Bidgol Lake (Iran), has the ability to produce acetone, butanol, and ethanol (ABE) as well as acetic and butyric acids under aerobic and anaerobic conditions. This result is the first report of ABE production with a wild microorganism from a family other than Clostridia and also the first halophilic species shown to produce butanol under aerobic cultivation. The cultivation of Nesterenkonia sp. strain F under anaerobic conditions with 50 g/l of glucose for 72 h resulted in the production of 105 mg/l of butanol, 122 mg/l of acetone, 0.2 g/l of acetic acid, and 2.5 g/l of butyric acid. Furthermore, the strain was cultivated on media with different glucose concentrations (20, 50, and 80 g/l) under aerobic and anaerobic conditions. Through fermentation with a 50 g/l initial glucose concentration under aerobic conditions, 66 mg/l of butanol, 125 mg/l of acetone, 291 mg/l of ethanol, 5.9 g/l of acetic acid, and 1.2 g/l of butyric acid were produced. The enzymes pertaining to the fermentation pathway in the strain were compared with the enzymes of Clostridium spp., and the metabolic pathway of fermentation used by Nesterenkonia sp. strain F was investigated.

Cerebral dynamics of N-isopropyl-(123I)p-iodoamphetamine

International Nuclear Information System (INIS)

Creutzig, H.; Schober, O.; Gielow, P.; Friedrich, R.; Becker, H.; Dietz, H.; Hundeshagen, H.

1986-01-01

Temporal changes in the distribution of N-isopropyl-(123I)p-iodoamphetamine (IMP) within the brain are measured with serial tomographic imaging. In the cerebellum there is a decrease in activity of 42% from the early [15-45 min postinjection (p.i.)] to the late (210-240 min p.i.) scan, while in the cortex the decrease is 18%, and in the basal ganglia there is no decrease within this time. In brain tumors there was no IMP uptake in the early as well as in the late scans, regardless of tumor type, perfusion rate, or blood-brain barrier dysfunction. In 11 of 43 patients with a cerebral infarction a real increase of 123I activity (mean +21%) was seen in the late images. This ''filling in'' phenomena might be useful in selecting patients for bypass surgery. In these patients the diaschisis cerebelli, seen in the early scans, disappeared in the late images. The regional distribution of IMP changes with time; spatial ratios might be blurred by temporal changes. High-flow areas such as visio-auditory centers can be delineated clearly after stimulation in fast early scans; in these areas the pharmacokinetics of 123I are different from other cortex regions. To get the full information from the IMP brain uptake, both spatial and temporal variation must be measured

In situ hydrogen, acetone, butanol, ethanol and microdiesel production by Clostridium acetobutylicum ATCC 824 from oleaginous fungal biomass.

Science.gov (United States)

Hassan, Elhagag Ahmed; Abd-Alla, Mohamed Hemida; Bagy, Magdy Mohamed Khalil; Morsy, Fatthy Mohamed

2015-08-01

An in situ batch fermentation technique was employed for biohydrogen, acetone, butanol, ethanol and microdiesel production from oleaginous fungal biomass using the anaerobic fermentative bacterium Clostridium acetobutylicum ATCC 824. Oleaginous fungal Cunninghamella echinulata biomass which has ability to accumulate up to 71% cellular lipid was used as the substrate carbon source. The maximum cumulative hydrogen by C. acetobutylicum ATCC 824 from crude C. echinulata biomass was 260 ml H2 l(-1), hydrogen production efficiency was 0.32 mol H2 mole(-1) glucose and the hydrogen production rate was 5.2 ml H2 h(-1). Subsequently, the produced acids (acetic and butyric acids) during acidogenesis phase are re-utilized by ABE-producing clostridia and converted into acetone, butanol, and ethanol. The total ABE produced by C. acetobutylicum ATCC 824 during batch fermentation was 3.6 g l(-1) from crude fungal biomass including acetone (1.05 g l(-1)), butanol (2.19 g l(-1)) and ethanol (0.36 g l(-1)). C. acetobutylicum ATCC 824 has ability to produce lipolytic enzymes with a specific activity 5.59 U/mg protein to hydrolyze ester containing substrates. The lipolytic potential of C. acetobutylicum ATCC 824 was used as a biocatalyst for a lipase transesterification process using the produced ethanol from ABE fermentation for microdiesel production. The fatty acid ethyl esters (microdiesel) generated from the lipase transesterification of crude C. echinulata dry mass was analyzed by GC/MS as 15.4% of total FAEEs. The gross energy content of biohydrogen, acetone, butanol, ethanol and biodiesel generated through C. acetobutylicum fermentation from crude C. echinulata dry mass was 3113.14 kJ mol(-1). These results suggest a possibility of integrating biohydrogen, acetone, butanol and ethanol production technology by C. acetobutylicum with microdiesel production from crude C. echinulata dry mass and therefore improve the feasibility and commercialization of bioenergy production

First-principles investigations of electronic and magnetic properties of SrTiO3 (001) surfaces with adsorbed ethanol and acetone molecules

Science.gov (United States)

Adeagbo, Waheed A.; Fischer, Guntram; Hergert, Wolfram

2011-05-01

First-principles methods based on density functional theory are used to investigate the electronic and magnetic properties of molecular interaction of the TiO2 terminated SrTiO3 (100) surface with ethanol or acetone. Both the perfect surface and the surface with an oxygen or a titanium vacancy in the top layer are considered. Ethanol and acetone are preferentially adsorbed molecularly via their respective oxygen atom on top of the Ti atom on the perfect surface. In case of an oxygen vacancy the adsorption of ethanol or acetone occurs directly on top of the vacancy and does not significantly affect the magnetism caused by the vacancy. In the case of a titanium vacancy both adsorbates occupy positions above Ti atoms. During this adsorption process the ethanol molecule dissociates into a CH3CO radical and three hydrogen atoms. The latter form hydroxide bonds with three of the four dangling oxygen bonds around the Ti vacancy and any magnetic moment induced by the Ti vacancy is annihilated. Thus the ethanol and acetone have a different impact on the surface magnetism of the SrTiO3 (100) surface.

Study on the noncoincidence effect phenomenon using matrix isolated Raman spectra and the proposed structural organization model of acetone in condense phase

Science.gov (United States)

Xu, Wenwen; Wu, Fengqi; Zhao, Yanying; Zhou, Ran; Wang, Huigang; Zheng, Xuming; Ni, Bukuo

2017-03-01

The isotropic and anisotropic Raman spectra of acetone and deuterated acetone isolated in an argon matrix have been recorded for the understanding of noncoincidence effect (NCE) phenomenon. According to the matrix isolated Raman spectra and DFT calculations, we proposed aggregated model for the explanations of the acetone C=O vibration NCE phenomenon and its concentration effect. The experimental data were in consistence with the DFT calculations performed at the B3LYP-D3/6-311 G (d,p) levels based on the proposed model. The experimental identification of the monomer, dimer and trimer are reported here, and the dynamic of the transformation from monomer to aggregated structure can be easily controlled by tuning annealing temperature.

Mathematical modeling of blood-gas kinetics for the volatile organic compounds isoprene and acetone

International Nuclear Information System (INIS)

King, J.

2010-01-01

Breath gas analysis is based on the compelling concept that the exhaled breath levels of endogenously produced volatile organic compounds (VOCs) can provide a direct, non-invasive window to the blood and hence, by inference, to the body. In this sense, breath VOCs are regarded as a comprehensive repository of valuable physiological and clinical information, that might be exploited in such diverse areas as diagnostics, therapeutic monitoring or general dynamic assessments of metabolic function, pharmacodynamics (e.g., in drug testing) and environmental exposure (e.g., in occupational health). Despite this enormous potential, the lack of standardized breath sampling regimes as well as the poor mechanistic understanding of VOC exhalation kinetics could cast a cloud over the widespread use of breath gas analysis in the biomedical sciences. In this context, a primary goal of the present thesis is to provide a better quantitative insight into the breath behavior of two prototypic VOCs, isoprene and acetone. A compartmental modeling framework is developed and validated by virtue of real-time breath measurements of these trace gases during distinct physiological states. In particular, the influence of various hemodynamic and ventilatory parameters on VOC concentrations in exhaled breath is investigated. This approach also complements previous steady state investigations in toxicology. From a phenomenological point of view, both acetone and isoprene concentrations in end-tidal breath are demonstrated to exhibit a reproducible non-steady state behavior during moderate workload challenges on a stationary bicycle. However, these dynamics depart drastically from what is expected on the basis of classical pulmonary inert gas elimination theory. More specifically, the start of exercise is accompanied by an abrupt increase in breath isoprene levels, usually by a factor of 3 to 4 compared with the steady state value during rest. This phase is followed by a gradual decline and the

Aldol Condensation of Citral with Acetone on Basic Solid Catalysts

Directory of Open Access Journals (Sweden)

NODA C.

1998-01-01

Full Text Available The catalytic performance of solids with basic properties, such as CaO, MgO and hydrotalcites, was evaluated in the aldol condensation of citral and acetone, the first step in the synthesis of ionones from citral. The best results were obtained with CaO and hydrotalcite with high conversions (98% and selectivities (close to 70% for the main product observed for both of the catalyst. Such pseudoionone yields were greater than those reported in the literature for the homogeneous reaction.

Molybdenum(5) template action in acetone with ethylenediamine condensation reaction

International Nuclear Information System (INIS)

Ashurova, N.Kh.; Yakubov, K.G.; Tsivadze, A.Yu.; AN SSSR, Moscow

1994-01-01

Ability of molybdenum(5) oxopentahalides [MoOX 5 ] 2- (X = Cl - , Br - ) to show their template action in acetone with ethylenediamine condensation reaction is identified. Macrocyclic metallic complexes [MoO(Td)X]X 2 , where Td is 5,7,7,12,14,14 hexamethyl-1,4,8,11-tetraazacyclotetradeca-4,11 dien, are separated and identified. Perchlorate salt of Td·2HClO 4 macrocycle is obtained through action of concentrated perchloric acid on synthesized complexes. 13 refs.; 3 figs

Production of acetone, butanol, and ethanol from biomass of the green seaweed Ulva lactuca

NARCIS (Netherlands)

Wal, van der H.; Sperber, B.L.H.M.; Houweling-Tan, G.B.N.; Bakker, R.R.C.; Brandenburg, W.A.; Lopez Contreras, Ana

2013-01-01

Green seaweed Ulva lactuca harvested from the North Sea near Zeeland (The Netherlands) was characterized as feedstock for acetone, ethanol and ethanol fermentation. Solubilization of over 90% of sugars was achieved by hot-water treatment followed by hydrolysis using commercial cellulases. A

Composition tunable cobalt–nickel and cobalt–iron alloy nanoparticles below 10 nm synthesized using acetonated cobalt carbonyl

International Nuclear Information System (INIS)

Schooneveld, Matti M. van; Campos-Cuerva, Carlos; Pet, Jeroen; Meeldijk, Johannes D.; Rijssel, Jos van; Meijerink, Andries; Erné, Ben H.; Groot, Frank M. F. de

2012-01-01

A general organometallic route has been developed to synthesize Co x Ni 1−x and Co x Fe 1−x alloy nanoparticles with a fully tunable composition and a size of 4–10 nm with high yield. In contrast to previously reported synthesis methods using dicobalt octacarbonyl (Co 2 (CO) 8 ), here the cobalt–cobalt bond in the carbonyl complex is first broken with anhydrous acetone. The acetonated compound, in the presence of iron carbonyl or nickel acetylacetonate, is necessary to obtain small composition tunable alloys. This new route and insights will provide guidelines for the wet-chemical synthesis of yet unmade bimetallic alloy nanoparticles.

Production of acetone, butanol, and ethanol from biomass of the green seaweed Ulva lactuca.

Science.gov (United States)

van der Wal, Hetty; Sperber, Bram L H M; Houweling-Tan, Bwee; Bakker, Robert R C; Brandenburg, Willem; López-Contreras, Ana M

2013-01-01

Green seaweed Ulva lactuca harvested from the North Sea near Zeeland (The Netherlands) was characterized as feedstock for acetone, ethanol and ethanol fermentation. Solubilization of over 90% of sugars was achieved by hot-water treatment followed by hydrolysis using commercial cellulases. A hydrolysate was used for the production of acetone, butanol and ethanol (ABE) by Clostridium acetobutylicum and Clostridium beijerinckii. Hydrolysate-based media were fermentable without nutrient supplementation. C. beijerinckii utilized all sugars in the hydrolysate and produced ABE at high yields (0.35 g ABE/g sugar consumed), while C. acetobutylicum produced mostly organic acids (acetic and butyric acids). These results demonstrate the great potential of U. lactuca as feedstock for fermentation. Interestingly, in control cultures of C. beijerinckii on rhamnose and glucose, 1,2 propanediol was the main fermentation product (9.7 g/L). Copyright © 2012 Elsevier Ltd. All rights reserved.

Skin Sterility After Application of a Vapocoolant Spray Part 2.

Science.gov (United States)

Mlynek, Karolina; Lyahn, Hwang; Richards, Bryson; Schleicher, William; Bassiri Gharb, Bahar; Procop, Gary; Tuohy, Marion; Zins, James

2015-08-01

Refrigerant sprays have been used for pain relief at the time of minor office procedures. However, their sterility remains in question. This study investigates the microbiologic effect of this vapocoolant when sprayed after 70 % isopropyl alcohol skin preparation. In 50 healthy volunteers, three skin culture samples were collected: Group 1 prior to alcohol application; Group 2 after preparation with alcohol, and Group 3 after preparation with alcohol followed with vapocoolant spray. Samples were cultured in a blinded fashion and analyzed after 5 days of incubation. Gram staining was performed when cultures were positive. Bacterial growth was found in 98 % of samples prior to any skin preparation. This was reduced to 54 % after alcohol use (Group 2). Spraying with the skin refrigerant further reduced bacterial growth to 46 % (Group 3). The results showed a significant reduction in the number of positive bacterial cultures following skin preparation with alcohol and when alcohol prep was followed by vapocoolant spray (p < 0.001) compared to initial cultures. No statistical difference was observed between Groups 2 and 3 (p = 0.74). The use of the vapocoolant spray does not compromise the sterility of the skin following alcohol prep. Both 70 % isopropyl alcohol antiseptic preparation and skin preparation followed by vapocoolant spray significantly reduce skin colonization when compared to unprepared skin (p < 0.001).

Acidolysis small molecular phenolic ether used as accelerator in photosensitive diazonaphthaquinone systems

Science.gov (United States)

Zhou, Haihua; Zou, Yingquan

2006-03-01

The photosensitive compounds in the photosensitive coatings of positive PS plates are the diazonaphthaquinone derivatives. Some acidolysis small molecular phenolic ethers, which were synthesized by some special polyhydroxyl phenols with vinyl ethyl ether, are added in the positive diazonaphthaquinone photosensitive composition to improve its sensitivity, composed with photo-acid-generators. The effects to the photosensitivity, anti-alkali property, anti-isopropyl alcohol property, dot resolution and line resolution of the coatings are studied with different additive percent of the special phenolic ethers. In the conventional photosensitive diazonaphthaquinone systems for positive PS plates, the photosensitivity is improved without negative effects to resolution, anti-alkali and anti-isopropyl alcohol properties when added about 5% of the special acidolysis phenolic ethers, EAAE or DPHE, composed with photo-acid-generators.

N-isopropyl-123I-p-iodoamphetamine uptake mechanism in the lung - is it dependent on pH, lipophilicity or pKa?

International Nuclear Information System (INIS)

Akber, S.F.

1991-01-01

The uptake and binding mechanism of biogenic amines in the lungs has been studied extensively with no conclusive results. The competition between N-isopropyl- 123 I-p-iodo amphetamines ( 123 I-IMP) and propranolol and 123 I-IMP and ketamine, in the lungs suggest that the pK a value of the biogenic amines has a significant role to play in the mechanism of uptake and retention of biogenic amines in the lungs. (orig.) [de

Assessment of in situ butanol recovery by vacuum during acetone butanol ethanol (ABE) fermentation

Science.gov (United States)

Butanol fermentation is product limiting due to butanol toxicity to microbial cells. Butanol (boiling point: 118 deg C) boils at a greater temperature than water (boiling point: 100 deg C) and application of vacuum technology to integrated acetone-butanol-ethanol (ABE) fermentation and recovery may ...

Biofiltration of a styrene/acetone vapor mixture in two reactor types under conditions of styrene overloading

Directory of Open Access Journals (Sweden)

Lubos Zapotocky

2014-10-01

Full Text Available This aim of study was to compare the performance of a biofilter (BF and trickle bed reactor (TBR under increased styrene loading with a constant acetone load, 2 gc/m3/h. At styrene loading rates up to 30 gc/m3/h, the BF showed higher styrene removal than TBR. However, the BF efficiency started to drop beyond this threshold loading and could never reach steady state, whereas the TBR continued to yield a 50% styrene removal. The acetone removal remained constant (93-98% in both the reactors at any styrene loading. Once the overloading was lifted, the BF recovered within 26 min, whereas the TBR efficiency bounced back only to 95%, gradually returning to complete removal only in 10 h.

Synthesis of La2O3 doped Zn2SnO4 hollow fibers by electrospinning method and application in detecting of acetone

Science.gov (United States)

Yang, H. M.; Ma, S. Y.; Yang, G. J.; Chen, Q.; Zeng, Q. Z.; Ge, Q.; Ma, L.; Tie, Y.

2017-12-01

Hollow porous pure and La2O3 doped Zn2SnO4 fibers were synthesized via single capillary electrospinning technology and used for obtaining of gas sensors. The as-prepared samples were characterized by microscopy, Brunauer-Emmett-Teller, X-ray photoelectron spectroscopy and UV-vis absorption spectra. The newly obtained gas sensors were investigated for acetone detection. Compared with pure Zn2SnO4 hollow fibers, the La2O3 doped Zn2SnO4 hollow fibers not only exhibited perfect sensing performance toward acetone with excellent selectivity, high response and fast response/recovery capability (7 s for adsorption and 9 s for desorption), but also the operating temperature was reduced from 240 °C to 200 °C. These results demonstrated that the special hollow porous La doped Zn2SnO4 fibers structures were used as the sensing material for fabricating high performance acetone sensors. The acetone sensing mechanism of La2O3 doped Zn2SnO4 hollow fibers was discussed too.

Influence of concentration of sucrose on the acetone-butanol fermentation by different strains of Clostridium

Energy Technology Data Exchange (ETDEWEB)

Bahadur, K; Saroj, K K

1959-01-01

To culture media containing (NH/sub 4/)/sub 2/SO/sub 4/ (0.34 g) and MgSO/sub 4/ (0.16 g), were added 5, 10, and 20% sucrose, respectively; the pH was adjusted to 6.4 with KH/sub 2/PO/sub 4/-NaOH buffer; the volume of each medium was made up to 200 ml. The media were sterilized. After cooling, the media at the 5, 10, 20% sucrose levels were inoculated separately with C. butyricum, C. butyricum 6084, C. acetobutylicum NRRL B-527, C. pasteurianum NRRL B-598, C. butylicus NRRL B-592, nd C. pasteurianum ATCC 6013. The cultures were incubated for 20 days at 35/sup 0/. For maximum BuOH yield the 5% sucrose level was optimum for all the strains tested. At the 10% sucrose level great increase in sugar consumption occurred with C. butyricum Frolund, C. pasteurianum ATCC-6013, and C. butylicus IAL 15-152. Twice as much sucrose was consumed with C. acetobutylicum ATCC 10132, and NRRL B-572, and C. pasteurianum NRRL B-598. The increased sucrose consumption did not result in increased production of BuOH or acetone. No acetone or BuOH was formed with C. butyricum Frolund when the sucrose concentration was increased from 5 to 10%. With the increase in sucrose concentration, the formation of BuH and acetone decreased; acid formation was also inhibited.

Synthesis of Ce-doped SnO{sub 2} nanoparticles and their acetone gas sensing properties

Energy Technology Data Exchange (ETDEWEB)

Lian, Xiaoxue, E-mail: lianxiaoxues@163.com; Li, Yan; Tong, Xiaoqiang; Zou, Yunling; Liu, Xiulin; An, Dongmin; Wang, Qiong

2017-06-15

Highlights: • The Ce-doped SnO{sub 2} nanoparticles were fabricated via a simple hydrothermal method. • Ce ions were successfully doped into the SnO{sub 2} lattice, and 5 wt% SnO{sub 2}:Ce had a higher specific surface area. • The Ce-doped SnO{sub 2} nanoparticles exhibited the highest response values and a well selectivity to acetone. - Abstract: Hydrothermal method was generally used to synthesis nanoparticles, which was used to fabricate pure and Ce-doped (3 wt%, 5 wt%, 7 wt%) SnO{sub 2} nanoparticles in this experiment. The as-prepared products were characterized by X-ray diffraction (XRD), energy dispersive spectrum (EDS), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Brunauer–Emmett–Teller (BET). The results clearly indicated that the nanoparticles were composed of SnO{sub 2} nanoparticles and Ce ions were successfully doped into the SnO{sub 2} lattice, and 5 wt% SnO{sub 2}:Ce has a higher specific surface area (173.53 m{sup 2}/g). Importantly, SnO{sub 2}:Ce sensor had obviously improved performance compared to pure SnO{sub 2} and exhibited the highest response values (50.5 for 50 ppm) and a well selectivity to acetone at 270 °C. It could detect acetone gas in a wide concentration range with very high response, good long-term stability and repeatability of response. The possible sensing mechanism was discussed in this paper.

The study analysis of degradation product of Tributyl Phosphate by Gamma radiation and influence in extraction process

International Nuclear Information System (INIS)

Damunir; Didiek Herhady, R; Busron-Masduki; Ashar-Waskito; Armanu

1996-01-01

The analysis study of degradation product of TBP by gamma radiation using Co-60 Irradiator Irvasena was done. The investigation stressed on analysis and the relation of degradation product of TBP and extraction process. TBP-dodecane 30 % irradiated by radiation doses 1.172x10 3 rad, 1.155x10 5 rad, 1.125x10 7 and 1.155x10 9 rad. The analysis of degradation product of TBP mainly of MBP and DBP were determined in the mixture media of 5 ml isopropyl alcohol, 5 ml ethylene glycol, 5 ml acetone and 15 ml alcohol with potentiometric titration using NaOH 0.1 N in the alcohol solution, at potential condition of 500 mV and potential derivative 500 mV. The experiment shows that the gamma radiation doses 1.125x10 7 rad result 0.125 ± 0.049 mg MBP/ml solvent and 1.556 ± 0.084 mg DBP/ml solvent and radiation doses 1.115x10 9 rad result 26.135 ± 0.114 mg MBP/ml solvent and 62.454 ± 1.107 mg DBP/ml solvent, MBP dan DBP un detectable for radiation doses 1.172x10 3 rad and 1.055x10 5 rad. The result of MBP and DBP analysis compare to Tachehiko Ishihara and Erich Zimmer, using potentiometric titration method for MBP and DBP analysis was reliable addition and none addition. The TBP-dodecane solvent was irradiation by radiation doses 10 7 rad or greater than, is suggested to treat the solvent by regeneration so that doesn't disturbance extraction

Quantitative phosphoproteomics using acetone-based peptide labeling: Method evaluation and application to a cardiac ischemia/reperfusion model

Science.gov (United States)

Wijeratne, Aruna B.; Manning, Janet R.; Schultz, Jo El J.; Greis, Kenneth D.

2013-01-01

Mass spectrometry (MS) techniques to globally profile protein phosphorylation in cellular systems that are relevant to physiological or pathological changes have been of significant interest in biological research. In this report, an MS-based strategy utilizing an inexpensive acetone-based peptide labeling technique known as reductive alkylation by acetone (RABA) for quantitative phosphoproteomics was explored to evaluate its capacity. Since the chemistry for RABA-labeling for phosphorylation profiling had not been previously reported, it was first validated using a standard phosphoprotein and identical phosphoproteomes from cardiac tissue extracts. A workflow was then utilized to compare cardiac tissue phosphoproteomes from mouse hearts not expressing FGF2 vs. hearts expressing low molecular weight fibroblast growth factor-2 (LMW FGF2) to relate low molecular weight fibroblast growth factor-2 (LMW FGF2) mediated cardioprotective phenomena induced by ischemia/reperfusion (I/R) injury of hearts, with downstream phosphorylation changes in LMW FGF2 signaling cascades. Statistically significant phosphorylation changes were identified at 14 different sites on 10 distinct proteins including some with mechanisms already established for LMW FGF2-mediated cardioprotective signaling (e.g. connexin-43), some with new details linking LMW FGF2 to the cardioprotective mechanisms (e.g. cardiac myosin binding protein C or cMyBPC), and also several new downstream effectors not previously recognized for cardio-protective signaling by LMW FGF2. Additionally, one of the phosphopeptides, cMyBPC/pSer-282, identified was further verified with site-specific quantification using an SRM (selected reaction monitoring)-based approach that also relies on isotope labeling of a synthetic phosphopeptide with deuterated acetone as an internal standard. Overall, this study confirms that the inexpensive acetone-based peptide labeling can be used in both exploratory and targeted quantification

Increased accumulation of N-isopropyl-p-(123I)-iodoamphetamine in two cases with mitochondrial encephalomyopathy with lactic acidosis and strokelike episodes (MELAS)

International Nuclear Information System (INIS)

Morita, K.; Ono, S.; Fukunaga, M.; Morita, R.; Yasuda, T.; Higashi, Y.; Terao, A.

1989-01-01

We present two cases with mitochondrial encephalopathy with lactic acidosis and strokelike episodes (MELAS), which showed both increased and decreased accumulation of N-isopropyl-p-( 123 I)-iodoamphetamine ( 123 I-IMP) in single photon emission computed tomography (SPECT). The increased accumulation of the tracer occurred before low density appeared on conventional computed tomography, suggesting that 123 I-IMP SPECT may be useful in pathophysiological study of MELAS. (orig.)

Iminium-ion formation and deuterium exchange by acetone in the presence of pyrrolidine, pyrazolidine, isoxazolidine, and their acyclic analogues

International Nuclear Information System (INIS)

Hine, J.; Evangelista, R.A.

1980-01-01

Equilibrium constants for iminium-ion-formation in the reaction of in acetone in aqueous solution at 35 0 C with pyrazolidinium, isoxazolidinium, O,N-dimethylhydroxylammonium, and N,N'-dimethylhydrazinium ions were found to be 9.33, 8.96, 0.117, and 0.057 M -1 , respectively. The kinetics of hydrolysis of the iminium ions were studied in every case except that of the N-isopropylidene-O,N-dimethylhydroxylammonium ion, whose hydrolysis is too fast to follow by the techniques used with the other iminium ions. The rate of hydrolysis of the N-isopropylidenepyrazolidinium ion is independent of the pH from about pH 3 to 6; it is hydrogen ion catalyzed at lower pHs and hydroxide ion catalyzed at higher pHs. The rate of hydrolysis of N-isopropylidenisoxazolidinium ions is Ph independent from pH 0.5 to about 2, increases until about pH 4, remains pH independent until pH 6.5, and has become too fast to measure above pH 8. Both reactions are general base catalyzed in all the buffers studied. A mechanism is described to fit the kinetics of each of these reactions. The dedeuteration of acetone-d 6 was studied pyridine buffers in the presence of each of the four hydrazine and hydroxylamine derivatives and also in the presence of the dimethylammonium and pyrrolidinium ion. All six of these secondary ammonium ions catalyze the dedeuteration by transforming the acetone-d 6 to an iminium ion that is dedeuterated by pyridine more rapidly than the ketone is. The iminium-ion formation is a relatively rapid equilibrium in all cases except that of pyrrolidinium ions, where the intermediate iminium ion loses deuterium and hydrolyzes at comparable rates, and possibly the case of dimethylammonium ions, where the amount of catalysis via iminium-ion formation is too small to reveal mechanistic details. The effect of structure on the efficiency of catalysis of dedeuteration via iminium-ion formation is discussed. 3 figures, 7 tables

Growth-temperature-dependent optical and acetone detection properties of ZnO thin films

International Nuclear Information System (INIS)

Shewale, P. S.; Yu, Y. S.

2015-01-01

Zinc oxide (ZnO) thin films were prepared onto glass substrates at moderately low growth temperature by two-stage spray pyrolysis technique. The effects of growth temperature on structural, optical and acetone detection properties were investigated with X-ray diffractometry, a UV–visible spectrophotometer, photoluminescence (PL) spectroscopy and a homemade gas sensor testing unit, respectively. All the films are polycrystalline with a hexagonal wurtzite phase and exhibit a preferential orientation along [002] direction. The film crystallinity is gradually enhanced with an increase in growth temperature. The optical measurements show that all the films are physically highly transparent with a transmittance greater than 82% in the visible range. The band gap of the film is observed to exhibit a slight red shift with an increasing growth temperature. The PL studies on the films show UV/violet PL band at ∼ 395 nm. Among all the films investigated, the film deposited at 250 °C demonstrates a maximum sensitivity of 13% towards 20 ppm of acetone vapors at 300 °C operating temperature. (paper)

Development of Fourier transform mid-infrared calibrations to predict acetone, β-hydroxybutyrate, and citrate contents in bovine milk through a European dairy network.