WorldWideScience

Sample records for aceite combustible residual

  1. Decrease of noxious emissions in the residual fuel oil combustion; Disminucion de emisiones nocivas en la combustion de aceite combustible residual

    Energy Technology Data Exchange (ETDEWEB)

    Mandoki W, Jorge [Econergia S. de R. L. de C. V. Mexico, D. F. (Mexico)

    1994-12-31

    achieved. [Espanol] La combustion de aceite combustible residual emite sustancias nocivas como particulas carbonaceas, oxidos de nitrogeno y trioxido de azufre, a niveles inadmisibles. Agua emulsionada en el combustible reduce sustancialmente dichas emisiones, lograndose ademas, en la mayoria de los casos, un ahorro neto en el consumo de combustible. Se muestran los efectos beneficos de quemar el aceite combustible residual en forma de emulsion, asi como el metodo para producir una emulsion adecuada. La tecnologia del combustible emulsionado ofrece una opcion de bajo costo para reducir la contaminacion atmosferica. La calidad del aceite combustible residual ha estado declinando durante las ultimas decadas debido: 1. Al aumento en la produccion de petroleos crudos pesados generalmente con mayor contenido de asfaltenos y de azufre. 2. A menor disponibilidad de residuos de la destilacion al vacio debido a su conversion a productos de mayor valor. 3. A procesos de conversion mas intensivos, como cracking catalitico, {sup v}isbreaking{sup ,} etc., que aumentan la concentracion de asfaltenos en los fondos, ocasionando problemas de inestabilidad. 4. Al aumento en el contenido de vanadio y de otros metales a medida que aumenta la concentracion de asfaltenos. El uso de aceite combustible emulsionado proporciona un medio eficaz y economico para reducir sustancialmente las emisiones nocivas a la atmosfera. La emulsion contiene particulas de agua de un diametro entre 2 y 20 micras, dispersadas uniformemente dentro del aceite combustible, en una proporcion generalmente enter 5 y 10%; ademas contiene un agente tensioactivo para asegurar una emulsion estable, capaz de resistir los esfuerzos cortantes del sistema de bombeo y distribucion. Cuando las gotas de aceite combustible atomizado llegan a la camara de combustion, el agua esmulsionada en ellas se convierte instantaneamente en vapor de alta presion, ocasionando una violenta atomizacion secundaria. El efecto de esta atomizacion

  2. Diesel oil combustion in fluidized bed; Combustion de aceite diesel en lecho fluidizado

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Cazares, Mario [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1992-07-01

    The effect of the fluidized bed depth in the combustion in burning diesel oil in a fluidized bed, was analyzed. A self sustained combustion was achieved injecting the oil with an injector that utilized a principle similar to an automobile carburetor venturi. Three different depths were studied and it was found that the deeper the bed, the greater the combustion efficiency. Combustion efficiencies were attained from 82% for a 100mm bed depth, up to 96% for a 200mm bed depth. The diminution in the efficiency was mainly attributed to unburned hydrocarbons and to the carbon carried over, which was observed in the black smoke at the stack outlet. Other phenomena registered were the temperature gradient between the lower part of the bed and the upper part, caused by the fluidization velocity; additionally it was observed that the air employed for the oil injection (carbureting air) is the most important parameter to attain a complete combustion. [Espanol] Se analizo el efecto de la profundidad del lecho en la combustion al quemar aceite diesel en un lecho fluidizado experimental. Se logro combustion autosostenida inyectando el aceite con un inyector que utilizo un principio similar al venturi del carburador de automovil. Se estudiaron tres diferentes profundidades del lecho y se encontro que a mayor profundidad del lecho, mayor eficiencia de la combustion. Se lograron eficiencias de la combustion desde 82% para el lecho de 100 mm de profundidad hasta 96% para el de 200 mm. La disminucion de la eficiencia se atribuyo, principalmente, a los hidrocarburos no quemados y al carbon arrastrado, lo cual se observo en el humo negro a la salida de la chimenea. Otros fenomenos registrados fueron el gradiente de temperatura entre la parte baja del lecho y la parte superior causado por la velocidad de fluidizacion; ademas, se observo que el aire utilizado para inyectar el aceite (aire de carburacion) es el parametro mas importante para lograr una combustion completa.

  3. El biodiesel de aceite de higuerilla como combustible alternativo para motores diesel

    OpenAIRE

    ALIRIO BENAVIDES; PEDRO BENJUMEA; VESELINA PASHOVA

    2007-01-01

    En este artículo se presenta un estudio experimental sobre la producción y utilización del biodiesel de aceite de higuerilla. El máximo rendimiento de metilésteres en la reacción de transesterificación del aceite de higuerilla usado se obtiene bajo las siguientes condiciones: temperatura ambiente, una relación molar metanol/aceite de 9 y una concentración de catalizador de 0.8%. El biodiesel de aceite de higuerilla puede ser mezclado con el combustible diesel convencional derivado del petróle...

  4. EL BIODIESEL DE ACEITE DE HIGUERILLA COMO COMBUSTIBLE ALTERNATIVO PARA MOTORES DIESEL

    OpenAIRE

    BENAVIDES, ALIRIO; BENJUMEA, PEDRO; PASHOVA, VESELINA

    2007-01-01

    En este artículo se presenta un estudio experimental sobre la producción y utilización del biodiesel de aceite de higuerilla. El máximo rendimiento de metilésteres en la reacción de transesterificación del aceite de higuerilla usado se obtiene bajo las siguientes condiciones: temperatura ambiente, una relación molar metanol/aceite de 9 y una concentración de catalizador de 0.8%. El biodiesel de aceite de higuerilla puede ser mezclado con el combustible diesel convencional derivado del petróle...

  5. El aceite usado de motor como combustible alternativo

    OpenAIRE

    Coronado, Marcelo

    2016-01-01

    La inadecuada gestión del aceite usado origina una serie de problemas ambientales dentro de los cuales podríamos citar los siguientes: - Si el aceite usado es vertido al suelo, este destruye el humus, mata la materia viva que hay en el suelo y disminuye su fertilidad. Por infiltración contamina las aguas subterráneas haciéndolas inadecuadas para el uso humano.

  6. El biodiesel de aceite de higuerilla como combustible alternativo para motores diesel

    Directory of Open Access Journals (Sweden)

    ALIRIO BENAVIDES

    2007-01-01

    Full Text Available En este artículo se presenta un estudio experimental sobre la producción y utilización del biodiesel de aceite de higuerilla. El máximo rendimiento de metilésteres en la reacción de transesterificación del aceite de higuerilla usado se obtiene bajo las siguientes condiciones: temperatura ambiente, una relación molar metanol/aceite de 9 y una concentración de catalizador de 0.8%. El biodiesel de aceite de higuerilla puede ser mezclado con el combustible diesel convencional derivado del petróleo en proporciones hasta del 15%, sin que la mezcla resultante se salga de las especificaciones de calidad estipuladas en los estándares nacionales e internacionales para combustibles diesel. La mayor dificultad para el uso del biodiesel de aceite de higuerilla en motores es su alta viscosidad. Sin embargo este biocombustible presenta excelentes propiedades de flujo a baja temperatura (valores bajos para los puntos de nube y fluidez. Las pruebas en motor con mezclas biodiesel de higuerilla/diesel convencional, en el rango de proporciones de biodiesel ensayadas, muestran que ha medida que se incrementa la proporción de biodiesel en la mezcla aumenta el consumo específico de combustible, disminuye el dosado relativo, la opacidad de humos se disminuye levemente, mientras que el rendimiento efectivo y las emisiones de CO y CO2 prácticamente permanecen constantes

  7. Caracterización de biodiesel obtenido de aceite residual de cocina

    Directory of Open Access Journals (Sweden)

    Betselene Murcia Ordoñez

    2013-01-01

    Full Text Available Título corto: Biodiesel de aceite residual de cocina Título en ingles: "Characterization of Biodiesel obtained from waste cooking oil" Resumen Se realizó un análisis físico y químico a cada uno de los siguientes tipos de aceite: desechado proveniente de asaderos de pollo, usado de hogares y fresco adquirido en el mercado local de la ciudad de Florencia, Caquetá (Colombia. Se evaluaron los siguientes parámetros: Peso específico, índice de yodo, índice de saponificación, índice de refracción, humedad y materia volátil, punto de fusión, impurezas insolubles, índice de acidez, coeficiente específico de extinción valores K232 y K270, color y prueba de Kreiss. Igualmente se evaluaron los espectros UV-VIS de los tres tipos de aceite estudiados. Se ensayaron siete diferentes tipos de catalizadores para la reacción de transesterificación manteniendo en todos los casos la proporción de catalizador: aceite 38:190 (v/v, tiempo de reacción (2h y temperatura de reacción (60°C. Se lograron rendimientos de biodiesel de 75.8% de aceite desechado usando KOH 1,269%p/v/MeOH 99%; 87.50% de aceite usado con KOH 0,537%p/v/MeOH 99% y 86.60% de aceite fresco usando KOH 0,457%p/v/MeOH 99%. Al biodiesel obtenido en cada caso se le determinó peso específico, índice de refracción, humedad y materia volátil, cenizas sulfatadas, carbón residual, corrosión a la lámina de cobre y perfil de ácidos grasos. En todos los casos hubo predominio de ácido  palmítico, ácido  oléico y ácido  esteárico en los aceites usados y desechados. Del análisis por cromatografía de gases acoplada a espectrometría de masas se pudo establecer que el contenido total de ésteres metílicos de ácidos  grasos es del 98,38% para el biodiesel de aceite desechado; 99,53% para el biodiesel de aceite usado y 97, 69% para el biodiesel de aceite fresco. Palabras clave: aceite residual de cocina; biodiesel; ácidos grasos; transesterificación Abstract Aphysical and

  8. Biorremediación de un suelo agrícola impactado con aceite residual automotriz

    OpenAIRE

    Pasaye Anaya, Lizbeth

    2011-01-01

    El aceite residual automotriz (ARA) derivado del uso de automotores es una mezcla de hidrocarburos (HC) alifáticos, aromáticos y otros que en el suelo impide la actividad microbiana para el reciclaje de elementos esenciales para la vida. El objetivo de este trabajo fue analizar la biorremediación (BR) por bioestimulación (BS) de un suelo agrícola impactado con ARA. Para ello, el suelo contaminado con la mezcla de HC se biorremedió por BS con una solución mineral (SM), lombricomposta (LC) y ab...

  9. Influencia del porcentaje de mezcla del aceite de higuerilla en la obtención de combustible alternativo para motores diesel

    OpenAIRE

    Arnoldo Emilio Delgado; Willian Aperador Chaparro; Jorge Réne Silva Gonzalez

    2011-01-01

    En el presente artículo se describe el uso del aceite de higuerilla como combustible alternativo en motores diesel. Para este fi n, se obtiene biodiesel a partir de aceite de higuerilla mediante el proceso de transesterifi cación. Se prueban tres mezclas de biodiesel (B5%, B10% y B20%) en un motor diesel, para el cual se midieron los siguientes parámetros: la potencia, el consumo de combustible, la temperatura del motor, y los gases de combustión;las mezclas fueron caracterizadas mediante la ...

  10. Fluidised-bed combustion of gasification residue

    Energy Technology Data Exchange (ETDEWEB)

    Korpela, T.; Kudjoi, A.; Hippinen, I.; Heinolainen, A.; Suominen, M.; Lu Yong [Helsinki Univ. of Technology (Finland). Lab of Energy Economics and Power Plant Engineering

    1996-12-01

    Partial gasification processes have been presented as possibilities for future power production. In the processes, the solid materials removed from a gasifier (i.e. fly ash and bed material) contain unburnt fuel and the fuel conversion is increased by burning this gasification residue either in an atmospheric or a pressurised fluidised-bed. In this project, which is a part of European JOULE 2 EXTENSION research programme, the main research objectives are the behaviour of calcium and sulphur compounds in solids and the emissions of sulphur dioxide and nitrogen oxides (NO{sub x} and N{sub 2}O) in pressurised fluidised-bed combustion of gasification residues. (author)

  11. Radioactivity of combustion residues from coal-fired power stations

    International Nuclear Information System (INIS)

    Vom Berg, W.; Puch, K.H.

    1996-01-01

    Each year in Germany, about 18 mill. t of combustion residues are produced from the combustion of bituminous coal and lignite. They are utilized to a great extent in the construction industry and in mining. During the combustion of coal, the radio-nuclides remain predominantly in the ash. The radionuclide concentration in lignite ash is within the range of that in natural soil. The combustion residues of bituminous coal contain radio-nuclides of a similar order of magnitude as also can occur in natural rock. The utilization of combustion residues in construction materials makes a negligible contribution to radiation exposure through retention in buildings. (orig.) [de

  12. Influencia del porcentaje de mezcla del aceite de higuerilla en la obtención de combustible alternativo para motores diesel

    Directory of Open Access Journals (Sweden)

    Arnoldo Emilio Delgado

    2011-01-01

    Full Text Available En el presente artículo se describe el uso del aceite de higuerilla como combustible alternativo en motores diesel. Para este fi n, se obtiene biodiesel a partir de aceite de higuerilla mediante el proceso de transesterifi cación. Se prueban tres mezclas de biodiesel (B5%, B10% y B20% en un motor diesel, para el cual se midieron los siguientes parámetros: la potencia, el consumo de combustible, la temperatura del motor, y los gases de combustión;las mezclas fueron caracterizadas mediante la densidad, viscosidad, índice de refracción y calor de combustión. Se determinó que el uso del aceite de higuerilla en la mezcla genera un aumento en la viscosidad y el consumo de combustible, además también infl uye en la reducción del poder calorífico, potencia del motor, los gases de combustión como el CO y CO2, los óxidos de azufre, los hidrocarburos, la opacidad en los humos del escape del motor y ocasiona un equilibrio en el rendimiento observado en el motor diesel, manifi esto en las temperaturas del motor.

  13. Caracterización química del aceite y harina residual de solanum sisymbriifolium lam

    Directory of Open Access Journals (Sweden)

    Wiese, B.

    2001-04-01

    Full Text Available Seeds from Solanum sisymbriifolium Lam harvested at Olavarría (Buenos Aires, Argentine were defatted with hexane and the raw oil obtained with a yield of 20,6 % dry basis. The physicochemical characteristics of crude oil were: refractive index: 1,4610 (at 25ºC, iodine value: 112,8; saponification index: 170,0; unsaponifiable matter: 14,0 % and free fatty acid content: 2,4 (mg KOH/g. The fatty acid composition of seed oil was studied by gas-liquid chromatography. Major fatty acids of seed oil were: linoleic (52,3%, oleic (23,4 % and palmitic acid (16,4 %. The residual seed meal contained moderate level of crude protein (14,75%, dry basis, low level of available lysine (2,25 g/16gN and high content of crude fiber (51,5%, dry basis. Total and phytic acid phosphorous, calcium, ash, sugar and polysaccharides contents are reported.Semillas de Solanum sisymbriifolium Lam cosechadas en Olavarría (prov. de Buenos Aires, Argentina se trataron con hexano (soxhlet obteniéndose el aceite crudo (rendimiento:20,6% y la harina residual de extracción. Las características fisicoquímicas del aceite crudo fueron: Índice de refracción: 1.4610 (a 25ºC; Índice de iodo: 112,8; Índice de saponificación: 170,0; Insaponificable: 14,0%, Índice de acidez: 2,4 (mgKOH/g. Se determinó la composición acídica del aceite por cromatografía gas-líquido. Los ácidos grasos mayoritarios fueron: ácido linoleico (52,3%, ácido oleico (23,4% y ácido palmítico (16,4%. La harina residual de extracción contenía una moderada proporción de proteína cruda (14,75% b.s, baja proporción de lisina disponible (2,25 g/16gN y un alto contenido de fibra cruda (51,5 %b.s. Se informan valores de fósforo total y de ácido fítico, cenizas, calcio e hidratos de carbono.

  14. Unburned carbon in combustion residues from mainly solid biofuels

    Energy Technology Data Exchange (ETDEWEB)

    Bjurstroem H; Lind B; Lagerkvist A

    2012-02-15

    Unburned carbon in 21 combustion residues from solid biofuels is investigated using several methods of analysis (a.o. LOI and TOC), as well as micro-Raman spectroscopy. The results are used to discuss the distribution of unburned carbon in the residues from the different combustion plants and its nature (organic or elemental). The consequences of the elemental nature of carbon for environmental properties of the residue are noted

  15. Aceite(s) remisión de V. expresoria de aceite(s).

    OpenAIRE

    2011-01-01

    [ES] Definición del término Aceite(s) remisión de V. expresoria de aceite(s). en el diccionario Dicter. [EN] Definition of the word Aceite(s) remisión de V. expresoria de aceite(s). in the dictionary Dicter.

  16. Estudios sobre semilla de Hypochaeris variegata L. (Baker: aceite seminal y harina residual de extracción

    Directory of Open Access Journals (Sweden)

    Nolasco, S. M.

    2000-08-01

    Full Text Available Seeds from Hypochaeris variegata L. (Baker harvested at Olavarría (Buenos Aires, Argentine were defatted with hexane and the raw oil obtained with a yield of 24,7% dry basis. The crude oil was examined in their physicochemical characteristics had refractive index of 1,4637 (at 25ºC, iodine value of 125,2, saponification index of 188,4, unsaponifiable matter of 8,5 % and free fatty acid content of 9,7 (mg KOH/g. Gas chromatographic analysis of the oil revealed high levels of linoleic acid (66,2%, appreciable amount of linolenic and erucic acids. The residual seed meal contained 35,49% of crude protein and 35,1% of crude fiber. Total and phytic acid phosphorous, calcium, ash, sugar and polisaccharides (non presence of starch contents are reported.Semillas de Hypochaeris variegata L. (Baker cosechadas en Olavarría (prov. de Buenos Aires, Argentina se extrajeron con hexano (soxhlet obteniéndose el aceite crudo con un rendimiento del 24,7 % (b.s. y la harina residual de extracción. El aceite crudo se examinó en sus características fisicoquímicas (Indice de refracción: 1.4637 (a 25ºC, Indice de iodo: 125,2, Indice de saponificación: 188,4, insaponificable: 8,5%, Indice de acidez: 9,7 (mgKOH/g y composición acídica. El análisis por cromatografía gaseosa de los ésteres metílicos revela un alto porcentaje de ácido linoleico (66,2%, cantidades apreciables de ácido linolénico y erúcico. La harina residual de extracción presentó un 35,49% b.s. de proteína cruda y 35,1% b.s. de fibra cruda. Se informan valores de fósforo total y de ácido fítico, cenizas, calcio e hidratos de carbono.

  17. Methodology for Evaluating Encapsulated Beneficial Uses of Coal Combustion Residuals

    Science.gov (United States)

    The primary purpose of this document is to present an evaluation methodology developed by the EPA for making determinations about environmental releases from encapsulated products containing coal combustion residuals.

  18. Fluidized bed and pulverized coal combustion residues for secondary pavements

    International Nuclear Information System (INIS)

    Ghafoori, N.; Diawara, H.; Wang, L.

    2009-01-01

    The United States produced nearly 125 million tons of coal combustion products in 2006. These by-products include fly ash, flue gas desulphurization materials, bottom ash, boiler slag, and other power plant by-products. The expense associated with waste disposal, lack of disposal sites, and significant environmental damage linked with the disposal of coal combustion residues have encouraged innovative utilization strategies such as the fluidized bed combustion (FBC) unit. This paper presented the results of a laboratory investigation that examined the properties of composites developed with different proportions of pre-conditioned FBC spent bed, pulverized coal combustion fly ash, natural fine aggregate, and Portland cement. The purpose of the study was to examine the extent to which the by-product composites could replace currently used materials in secondary roads. The paper presented the research objectives and experimental programs, including matrix constituent and proportions; mixture proportions; and mixing, curing, sampling, and testing. The discussion of results centered around compressive strength and expansion by internal sulfate attack. It was concluded that with proper proportioning, by-products of pulverized and fluidized bed combustion promote binding of sand particles and provide adequate strength under various curing and moisture conditions 4 refs., 6 tabs.

  19. Thermogravimetric investigation of the co-combustion between the pyrolysis oil distillation residue and lignite.

    Science.gov (United States)

    Li, Hao; Xia, Shuqian; Ma, Peisheng

    2016-10-01

    Co-combustion of lignite with distillation residue derived from rice straw pyrolysis oil was investigated by non-isothermal thermogravimetric analysis (TGA). The addition of distillation residue improved the reactivity and combustion efficiency of lignite, such as increasing the weight loss rate at peak temperature and decreasing the burnout temperature and the total burnout. With increasing distillation residue content in the blended fuels, the synergistic interactions between distillation residue and lignite firstly increased and then decreased during co-combustion stage. Results of XRF, FTIR, (13)C NMR and SEM analysis indicated that chemical structure, mineral components and morphology of samples have great influence on the synergistic interactions. The combustion mechanisms and kinetic parameters were calculated by the Coats Redfern model, suggesting that the lowest apparent activation energy (120.19kJ/mol) for the blended fuels was obtained by blending 60wt.% distillation residue during main co-combustion stage. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Coal Combustion Residual Beneficial Use Evaluation: Fly Ash Concrete and FGD Gypsum Wallboard

    Science.gov (United States)

    This page contains documents related to the evaluation of coal combustion residual beneficial use of fly ash concrete and FGD gypsum wallboard including the evaluation itself and the accompanying appendices

  1. Management of high sulfur coal combustion residues, issues and practices: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Chugh, Y.P.; Beasley, G.A. [eds.

    1994-10-01

    Papers presented at the following sessions are included in this proceedings: (1) overview topic; (2) characterization of coal combustion residues; (3) environmental impacts of residues management; (4) materials handling and utilization, Part I; and (5) materials handling and utilization, Part II. Selected paper have been processed separately for inclusion in the Energy Science and Technology Database.

  2. Characterizing the Leaching Behavior of Coal Combustion Residues using the Leaching Environmental Assessment Framework (LEAF) to Inform Future Management Decisions

    Science.gov (United States)

    Abstract for presentation on Characterizing the Leaching Behavior of Coal Combustion Residues using the Leaching Environmental Assessment Framework (LEAF) to Inform Future Management Decisions. The abstract is attached.

  3. Characterization, leachability and valorization through combustion of residual chars from gasification of coals with pine.

    Science.gov (United States)

    Galhetas, Margarida; Lopes, Helena; Freire, Márcia; Abelha, Pedro; Pinto, Filomena; Gulyurtlu, Ibrahim

    2012-04-01

    This paper presents the study of the combustion of char residues produced during co-gasification of coal with pine with the aim of characterizing them for their potential use for energy. These residues are generally rich in carbon with the presence of other elements, with particular concern for heavy metals and pollutant precursors, depending on the original fuel used. The evaluation of environmental toxicity of the char residues was performed through application of different leaching tests (EN12457-2, US EPA-1311 TCLP and EA NEN 7371:2004). The results showed that the residues present quite low toxicity for some of pollutants. However, depending on the fuel used, possible presence of other pollutants may bring environmental risks. The utilization of these char residues for energy was in this study evaluated, by burning them as a first step pre-treatment prior to landfilling. The thermo-gravimetric analysis and ash fusibility studies revealed an adequate thermochemical behavior, without presenting any major operational risks. Fluidized bed combustion was applied to char residues. Above 700°C, very high carbon conversion ratios were obtained and it seemed that the thermal oxidation of char residues was easier than that of the coals. It was found that the char tendency for releasing SO(2) during its oxidation was lower than for the parent coal, while for NO(X) emissions, the trend was observed to increase NO(X) formation. However, for both pollutants the same control techniques might be applied during char combustion, as for coal. Furthermore, the leachability of ashes resulting from the combustion of char residues appeared to be lower than those produced from direct coal combustion. Copyright © 2011 Elsevier Ltd. All rights reserved.

  4. Stabilization of Rocky Flats combustible residues contaminated with plutonium metal and organic solvents

    International Nuclear Information System (INIS)

    Bowen, S.M.; Cisneros, M.R.; Jacobson, L.L.; Schroeder, N.C.; Ames, R.L.

    1998-01-01

    This report describes tests on a proposed flowsheet designed to stabilize combustible residues that were generated at the Rocky Flats Environmental Technology Site (RFETS) during the machining of plutonium metal. Combustible residues are essentially laboratory trash contaminated with halogenated organic solvents and plutonium metal. The proposed flowsheet, designed by RFETS, follows a glovebox procedure that includes (1) the sorting and shredding of materials, (2) a low temperature thermal desorption of solvents from the combustible materials, (3) an oxidation of plutonium metal with steam, and (4) packaging of the stabilized residues. The role of Los Alamos National Laboratory (LANL) in this study was to determine parameters for the low temperature thermal desorption and steam oxidation steps. Thermal desorption of carbon tetrachloride (CCl 4 ) was examined using a heated air stream on a Rocky Flats combustible residue surrogate contaminated with CCl 4 . Three types of plutonium metal were oxidized with steam in a LANL glovebox to determine the effectiveness of this procedure for residue stabilization. The results from these LANL experiments are used to recommend parameters for the proposed RFETS stabilization flowsheet

  5. Morphology, composition, and mixing state of primary particles from combustion sources ? crop residue, wood, and solid waste

    OpenAIRE

    Liu, Lei; Kong, Shaofei; Zhang, Yinxiao; Wang, Yuanyuan; Xu, Liang; Yan, Qin; Lingaswamy, A. P.; Shi, Zongbo; Lv, Senlin; Niu, Hongya; Shao, Longyi; Hu, Min; Zhang, Daizhou; Chen, Jianmin; Zhang, Xiaoye

    2017-01-01

    Morphology, composition, and mixing state of individual particles emitted from crop residue, wood, and solid waste combustion in a residential stove were analyzed using transmission electron microscopy (TEM). Our study showed that particles from crop residue and apple wood combustion were mainly organic matter (OM) in smoldering phase, whereas soot-OM internally mixed with K in flaming phase. Wild grass combustion in flaming phase released some Cl-rich-OM/soot particles and cardboard combusti...

  6. Chemical analysis of solid residue from liquid and solid fuel combustion: Method development and validation

    Energy Technology Data Exchange (ETDEWEB)

    Trkmic, M. [University of Zagreb, Faculty of Mechanical Engineering and Naval Architecturek Zagreb (Croatia); Curkovic, L. [University of Zagreb, Faculty of Chemical Engineering and Technology, Zagreb (Croatia); Asperger, D. [HEP-Proizvodnja, Thermal Power Plant Department, Zagreb (Croatia)

    2012-06-15

    This paper deals with the development and validation of methods for identifying the composition of solid residue after liquid and solid fuel combustion in thermal power plant furnaces. The methods were developed for energy dispersive X-ray fluorescence (EDXRF) spectrometer analysis. Due to the fuels used, the different composition and the location of creation of solid residue, it was necessary to develop two methods. The first method is used for identifying solid residue composition after fuel oil combustion (Method 1), while the second method is used for identifying solid residue composition after the combustion of solid fuels, i. e. coal (Method 2). Method calibration was performed on sets of 12 (Method 1) and 6 (Method 2) certified reference materials (CRM). CRMs and analysis test samples were prepared in pellet form using hydraulic press. For the purpose of method validation the linearity, accuracy, precision and specificity were determined, and the measurement uncertainty of methods for each analyte separately was assessed. The methods were applied in the analysis of real furnace residue samples. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. The atomization and the flame structure in the combustion of residual fuel oils; La atomizacion y estructura de flama en la combustion de combustibles residuales

    Energy Technology Data Exchange (ETDEWEB)

    Bolado Estandia, Ramon [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1986-12-31

    In this article a research on the combustion of heavy residual fuel oils is presented. The type of flames studied were obtained by means of the burning of sprays produced by an atomizer designed and calibrated specially for the research purpose. The flame characteristics that were analyzed are its length, its luminosity, the temperature, the distribution of the droplets size and mainly the burning regime of the droplets in the flame. The experimental techniques that were used for these studies were shadow micro-photography, suction pyrometry and of total radiation, laser diffraction, 35 mm photography, and impact push. The analysis of the experimental results, together with the results of the application of a mathematical model, permitted to establish two parameters, that quantitatively related determine the burning regime of the droplets in a flame of sprays of residual heavy fuel oil. [Espanol] En este articulo se presenta una investigacion sobre la combustion de combustibles residuales pesados. El tipo de flamas estudiadas se obtuvieron mediante el quemado de sprays producidos por un atomizador disenado y calibrado especialmente para el proposito de la investigacion. Las caracteristicas de flama que se analizaron son la longitud, la luminosidad, la temperatura, la distribucion de tamano de gotas y, principalmente, el regimen de quemado de gotas en la flama. Las tecnicas experimentales que se usaron para estos estudios fueron microfotografia de sombras, pirometria de succion y de radiacion total, difraccion laser, fotografia de 35 mm y empuje de impacto. El analisis de resultados experimentales, junto con los resultados de la aplicacion de un modelo matematico, permitio establecer dos parametros, que relacionados cuantitativamente, determinan el regimen de quemado de gotas en una flama de sprays de combustible residual pesado.

  8. The atomization and the flame structure in the combustion of residual fuel oils; La atomizacion y estructura de flama en la combustion de combustibles residuales

    Energy Technology Data Exchange (ETDEWEB)

    Bolado Estandia, Ramon [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1985-12-31

    In this article a research on the combustion of heavy residual fuel oils is presented. The type of flames studied were obtained by means of the burning of sprays produced by an atomizer designed and calibrated specially for the research purpose. The flame characteristics that were analyzed are its length, its luminosity, the temperature, the distribution of the droplets size and mainly the burning regime of the droplets in the flame. The experimental techniques that were used for these studies were shadow micro-photography, suction pyrometry and of total radiation, laser diffraction, 35 mm photography, and impact push. The analysis of the experimental results, together with the results of the application of a mathematical model, permitted to establish two parameters, that quantitatively related determine the burning regime of the droplets in a flame of sprays of residual heavy fuel oil. [Espanol] En este articulo se presenta una investigacion sobre la combustion de combustibles residuales pesados. El tipo de flamas estudiadas se obtuvieron mediante el quemado de sprays producidos por un atomizador disenado y calibrado especialmente para el proposito de la investigacion. Las caracteristicas de flama que se analizaron son la longitud, la luminosidad, la temperatura, la distribucion de tamano de gotas y, principalmente, el regimen de quemado de gotas en la flama. Las tecnicas experimentales que se usaron para estos estudios fueron microfotografia de sombras, pirometria de succion y de radiacion total, difraccion laser, fotografia de 35 mm y empuje de impacto. El analisis de resultados experimentales, junto con los resultados de la aplicacion de un modelo matematico, permitio establecer dos parametros, que relacionados cuantitativamente, determinan el regimen de quemado de gotas en una flama de sprays de combustible residual pesado.

  9. Direct recovery of boiler residue by combustion synthesis.

    Science.gov (United States)

    Nourbaghaee, Homan; Ghaderi Hamidi, Ahmad; Pourabdoli, Mahdi

    2018-04-01

    Boiler residue (BR) of thermal power plants is one of the important secondary sources for vanadium production. In this research, the aluminothermic self-propagating high-temperature synthesis (SHS) was used for recovering the transition metals of BR for the first time. The effects of extra aluminum as reducing agent and flux to aluminum ratio (CaO/Al) were studied and the efficiency of recovery and presence of impurities were measured. Aluminothermic reduction of vanadium and other metals was carried out successfully by SHS without any foreign heat source. Vanadium, iron, and nickel principally were reduced and gone into metallic master alloy as SHS product. High levels of efficiency (>80%) were achieved and the results showed that SHS has a great potential to be an industrial process for BR recovery. SHS produced two useful products. Metallic master alloy and fused glass slag that is applicable for ceramic industries. SHS can also neutralize the environmental threats of BR by a one step process. Copyright © 2018 Elsevier Ltd. All rights reserved.

  10. Aceite de pescado deodorizado

    OpenAIRE

    Erausquín Leyva, Rolando; Vargas Chávez, Carlos; Randich Guevara, Rosana; Medina Yllesca, Víctor; Sattui Cubas, Piero

    2017-01-01

    Siendo el Perú el principal proveedor mundial de aceite de pescado, se ha identificado que en su mayoría solo es vendido en grado crudo, por lo cual existe una oportunidad de comercializar aceite deodorizado, es decir, sin olor de pescado, con un olor neutro y sin impurezas, y con una demanda por ser cubierta. Actualmente, existe una cantidad limitada de empresas que lo ofrecen. La empresa Blue Pacific Oils (BPO) es una empresa que comercializa productos líquidos en general y brinda servic...

  11. Utilization of stabilized municipal waste combustion ash residues as construction material

    International Nuclear Information System (INIS)

    Shieh, C.S.

    1992-01-01

    Stabilized municipal waste combustion (MWC) ash residues were investigated for their potential as construction material that can be beneficially used in terrestrial and marine environments. End-use products, such as patio stones, brick pavers, solid blocks, and reef units, were fabricated and tested for their engineering and chemical characteristics. engineering feasibility and environmental acceptability of using stabilized ash residues as construction material are discussed in this paper. Ash samples were collected from two mass-burn facilities and one refuse derived fuel (RDF) facility in Florida

  12. Recovery of plutonium from the combustion residues of alpha-bearing solid wastes

    International Nuclear Information System (INIS)

    Gompper, K.; Wieczorek, H.

    1991-01-01

    Experimental researches on plutonium dioxide dissolution in nitric acid in inactive and alpha-bearing wastes are presented in this report. After a review of the literature published on dissolution methods of PuO 2 combustion residues. Then results obtained in the ALONA plant on the dissolution of plutonium containing ashes in sulfuric acid and nitric acid are presented. Plutonium purification is studied. At last a simplified scheme of processing based on results obtained

  13. Beneficial Use and Recycling of Municipal Waste Combustion Residues - A Comprehensive Resource Document

    Energy Technology Data Exchange (ETDEWEB)

    Wiles, C.; Shepherd, P.

    1999-04-26

    This document summarizes information from worldwide sources on the beneficial use of residues from the combustion of municipal. The information presented, including results of numerous research projects, field demonstrations, and actual full-scale projects, demonstrates that the ash can be safely used. It includes data on ash characteristics, environmental considerations, guidance on selected ash use applications, and information on federal and state regulations and policies affecting ash use.

  14. Disposal of residue from sifting of combustible waste; Avsaettning av siktrest fraan foerbehandling av braennbart avfall

    Energy Technology Data Exchange (ETDEWEB)

    Niklasson, Fredrik

    2012-11-01

    In waste to energy plants, unwanted species in the fuel may cause corrosion, deposits, agglomeration in the fuel bed, and emissions of pollutants. Countermeasures to such problems are often costly. For at least some of the waste, the fuel properties can be improved by introducing a pretreatment system in which the fine fraction is separated from the waste by sifting. This method has been studied in an earlier Waste Refinery project, WR-06. That study pointed at advantages in performance of the boiler plant and a rough economical analysis indicated substantial benefits. The drawback of the pretreatment was that the residue (the fine fraction) showed as high content of total organic carbon (TOC) as 37 %, by weight. Such a waste fraction is not allowed to be landfilled in Sweden. High TOC content is also a limiting factor for usage as a secondary construction material. To become an applicable pretreatment method, it is necessary to find an appropriate disposal method for the residue material. Present work investigates different possibilities to handle the sifting residue, assuming it has the same properties as in previous study. The residue from sifting needs further treatment, preferably with energy recovery. There are some alternatives, such as combustion, gasification, anaerobic or aerobic digestion. To reduce problems associated by combustion, the waste may be burnt in another more suitable furnace. An alternative is gasification, but that treatment method is not yet an established process for waste fuels. Another option is treatment by anaerobic or aerobic digestion. The high concentrations of metals, however, limit the use of the biologically treated waste to landfilling sites, where it may be utilized as a construction material. The high metal concentrations in the sifting residue imply that it must be kept separate from other biodegradable wastes which are used to produce fertilizers. Thus, this treatment alternative will likely require substantial new

  15. del biodiesel de aceite de palma

    Directory of Open Access Journals (Sweden)

    Pedro Nel Benjumea

    2007-01-01

    Full Text Available El deficiente desempeño del biodiesel de aceite de palma (BAP a bajas temperaturas constituye su mayor deficiencia de calidad y el limitante para propiciar el uso de este combustible alternativo para motores diesel puro o mezclado en altas proporciones con el combustible diesel convencional derivado del petróleo (ACPM. En este trabajo se evalúan varias alternativas para mejorar las propiedades de flujo a baja temperatura (PFBT del BAP. Mediante la producción del biodiesel utilizando alcoholes ramificados como el isopropanol, isobutanol, 2-butanol e isopentanol se obtienen alquilésteres del aceite de palma con puntos de nube y fl uidez más bajos que los correspondientes a los metilésteres. La sustitución del grupo metil por el isopentil permite obtener reducciones en los puntos de nube y fluidez de 8 y 21 ºC, respectivamente. Los isopropilésteres del aceite de palma poseen un punto de nube 10 ºC menor que el de los metilésteres. El punto de nube de las mezclas BAP-ACPM se incrementa en forma lineal con el contenido del biodiesel en la mezcla. Para las mezclas probadas (B5, B20 y B30 solo se presentan problemas de filtrabilidad del combustible a temperaturas por debajo de -4 ºC. En este trabajo se evaluó la efectividad de dos aditivos comerciales mejoradores de flujo para reducir el punto de obstrucción de filtros en frío (POFF del biodiesel puro y las mezclas probadas. Los resultados obtenidos mostraron que con dichos aditivos solamente es posible obtener reducciones en el POFF de la mezcla B5 cuando se usa la menor de las tres concentraciones de aditivo probadas.

  16. Numerical investigation for combustion characteristics of vacuum residue (VR) in a test furnace

    International Nuclear Information System (INIS)

    Sreedhara, S.; Huh, Kang Y.; Park, Hoyoung

    2007-01-01

    It has become inevitable to search for alternative fuels due to current worldwide energy crisis. In this paper combustion characteristics of vacuum residue (VR) is investigated numerically against experimental data in typical operating conditions of a furnace. Heat release reaction is modeled as sequential steps of devolatilization, simplified gas phase reaction and char oxidation as for pulverized coal. Thermal and fuel NO are predicted by the conditional moment closure (CMC) method for estimation of elementary reaction rates. It turns out that Sauter mean diameter (SMD) of VR droplets is a crucial parameter for better combustion efficiency and lower NO. Reasonable agreement is achieved for spatial distributions of major species, temperature and NO for all test cases with different fuel and steam flow rates

  17. Instrumental neutron activation analysis of coal and its combustion residues from a power plant

    International Nuclear Information System (INIS)

    Lim, J.M.; Jeong, J.H.; Lee, J.H.

    2013-01-01

    A growing demand of electrical energy derived from coal combustion led to a significant increase of coal ash as residues. Approximately 70 % of the fly ashes are recycled, while most of the bottom ashes have been land-filled in the ash pond in Korea. In this work, to evaluate the potential impacts of the residues from a coal power plant on the environment, its inorganic elemental components were determined by INAA and PGAA. Coal ash samples were collected from the biggest power plant complex in Korea. These samples were analyzed by using the NAA facilities in the HANARO research reactor of the Korea Atomic Energy Research Institute. A total of 31 elements were analyzed in the samples, and certified reference materials were used for the analytical quality control. The enrichment status of a given metal in fuel coal and ashes was investigated by its concentration ratio. In order to assess the impact of the coal combustion residues on ecosystem, their concentrations determined for each respective type of the samples were compared to both reference data and nearby beach sand samples. (author)

  18. Morphology, composition, and mixing state of primary particles from combustion sources - crop residue, wood, and solid waste.

    Science.gov (United States)

    Liu, Lei; Kong, Shaofei; Zhang, Yinxiao; Wang, Yuanyuan; Xu, Liang; Yan, Qin; Lingaswamy, A P; Shi, Zongbo; Lv, Senlin; Niu, Hongya; Shao, Longyi; Hu, Min; Zhang, Daizhou; Chen, Jianmin; Zhang, Xiaoye; Li, Weijun

    2017-07-11

    Morphology, composition, and mixing state of individual particles emitted from crop residue, wood, and solid waste combustion in a residential stove were analyzed using transmission electron microscopy (TEM). Our study showed that particles from crop residue and apple wood combustion were mainly organic matter (OM) in smoldering phase, whereas soot-OM internally mixed with K in flaming phase. Wild grass combustion in flaming phase released some Cl-rich-OM/soot particles and cardboard combustion released OM and S-rich particles. Interestingly, particles from hardwood (pear wood and bamboo) and softwood (cypress and pine wood) combustion were mainly soot and OM in the flaming phase, respectively. The combustion of foam boxes, rubber tires, and plastic bottles/bags in the flaming phase released large amounts of soot internally mixed with a small amount of OM, whereas the combustion of printed circuit boards and copper-core cables emitted large amounts of OM with Br-rich inclusions. In addition, the printed circuit board combustion released toxic metals containing Pb, Zn, Sn, and Sb. The results are important to document properties of primary particles from combustion sources, which can be used to trace the sources of ambient particles and to know their potential impacts in human health and radiative forcing in the air.

  19. Identification of accelerants, fuels and post-combustion residues using a colorimetric sensor array.

    Science.gov (United States)

    Li, Zheng; Jang, Minseok; Askim, Jon R; Suslick, Kenneth S

    2015-09-07

    A linear (1 × 36) colorimetric sensor array has been integrated with a pre-oxidation technique for detection and identification of a variety of fuels and post-combustion residues. The pre-oxidation method permits the conversion of fuel vapor into more detectable species and therefore greatly enhances the sensitivity of the sensor array. The pre-oxidation technique used a packed tube of chromic acid on an oxide support and was optimized in terms of the support and concentration. Excellent batch to batch reproducibility was observed for preparation and use of the disposable pre-oxidation tubes. Twenty automotive fuels including gasolines and diesel from five gasoline retailers were individually identifiable with no confusions or misclassifications in quintuplicate trials. Limits of detection were at sub-ppm concentrations for gasoline and diesel fuels. In addition, burning tests were performed on commonly used fire accelerants, and clear differentiation was achieved among both the fuels themselves and their volatile residues after burning.

  20. Disposing of coal combustion residues in inactive surface mines: Effects on water quality

    International Nuclear Information System (INIS)

    Kim, A.G.; Ackman, T.E.

    1994-01-01

    The disposal of coal combustion residues (CCR) in surface and underground coal mines can provide a stable, low-maintenance alternative to landfills, benefiting the mining and electric power industries. The material may be able to improve water quality at acid generating abandoned or reclaimed coal mine sites. Most combustion residues are alkaline, and their addition to the subsurface environment could raise the pH, limiting the propagation of pyrite oxidizing bacteria and reducing the rate of acid generation. Many of these CCR are also pozzolanic, capable of forming cementitious grouts. Grouts injected into the buried spoil may decrease its permeability and porosity, diverting water away from the pyritic material. Both mechanisms, alkaline addition and water diversion, are capable of reducing the amount of acid produced at the disposal site. The US Bureau of Mines is cooperating in a test of subsurface injection of CCR into a reclaimed surface mine. Initially, a mixture of fly ash, lime, and acid mine drainage (AMD) sludge was injected. Lime was the source of calcium for the formation of the pozzolanic grout. Changes in water quality parameters (pH, acidity, anions, and trace metals) in water samples from wells and seeps indicate a small but significant improvement after CCR injection. Changes in the concentration of heavy metals in the water flowing across the site were apparently influenced by the presence of flyash

  1. Characterization of residues from waste combustion in fluidized bed boilers. Evaluation report

    International Nuclear Information System (INIS)

    Hagman, U.; Elander, P.

    1996-04-01

    In this report a thorough characterization of the solid residues from municipal solid waste combustion in a Kvaerner EnviroPower bubbling fluidized bed boiler in Lidkoeping, is presented. Three different end products are generated, namely bottom ash, cyclone ash, and filter ash. The bottom ash, consisting of bed ash and hopper ash, is screened and useful bed material recycled. In the characterization, also the primary constituents bed ash and hopper ash have been included. A chemical characterization have been performed including total inorganic contents, content of unburnt matter, leaching behaviour (availability tests, column tests, pH-static tests) and leaching tests according to certain standards for classification (AFX31-210, DIN38414, TCLP). Physical characterization have included grain size distribution, grain density, compaction properties and stabilization of cyclone ash with subsequent testing of comprehensive strength and saturated hydraulic conductivity. From an environmental point of view, the quality of the bottom ash and probably the cyclone ash from fluidized bed combustion as determined in this study, indicate a potential for utilization. Utilization of the bottom ash could be accepted in certain countries, e.g. France, according to their current limit values. In other countries, e.g. Sweden, no general limit values are given and utilization have to be applied for in each case. The judgement is then based, not only on total contents in the residue and its leaching behaviour, but also on the specific environmental conditions at the site. 7 refs, 17 figs, 12 tabs

  2. Combustion

    CERN Document Server

    Glassman, Irvin

    1987-01-01

    Combustion, Second Edition focuses on the underlying principles of combustion and covers topics ranging from chemical thermodynamics and flame temperatures to chemical kinetics, detonation, ignition, and oxidation characteristics of fuels. Diffusion flames, flame phenomena in premixed combustible gases, and combustion of nonvolatile fuels are also discussed. This book consists of nine chapters and begins by introducing the reader to heats of reaction and formation, free energy and the equilibrium constants, and flame temperature calculations. The next chapter explores the rates of reactio

  3. Thermal behavior of the major constituents of some agricultural biomass residues during pyrolysis and combustion

    Energy Technology Data Exchange (ETDEWEB)

    Yaman, S.; Haykiri-Acma, H. [Istanbul Technical Univ., Istanbul (Turkey). Dept. of Chemical Engineering, Chemical and Metallurgical Engineering Faculty

    2006-07-01

    The importance of woody agricultural waste as a renewable energy source was discussed with reference to its low cost, abundance, and carbon dioxide neutrality. Direct combustion of biomass waste fuels is not recommended due to its low density, high moisture content and low calorific energy. Rather, thermal conversion processes such as pyrolysis, gasification or carbonization are preferred for biomass. The performance and the energy recovery potentials of these processes depend on the process conditions as well as the physical and chemical properties of the biomass species. Therefore, the structure and components of biomass must be known. In this study, agricultural biomass samples of almond shell, walnut shell, hazelnut shell, rapeseed, olive residue, and tobacco waste were first analytically treated to remove extractive matter to obtain extractive-free samples. Specific analytic procedures were then applied to biomass samples in order to isolate their individual biomass constituents such as lignin and holocellulose. Untreated biomass samples and their isolated constituents were exposed to non-isothermal pyrolysis and combustion processes in a thermogravimetric analyzer. Pyrolysis experiments were conducted under dynamic nitrogen atmospheres of 40 mL-min, while dynamic dry air atmosphere with the same flow rate was applied in the combustion experiments. The study showed that the pyrolysis and combustion characteristics of the biomass samples differed depending on their properties. Aliphatic and oxygen rich holocellulose and cellulose were found to be the reactive components in biomass. Lignin was more stable during thermal processes. When extractive matter from the biomass samples was removed, pyrolysis at lower temperatures was terminated. 10 refs., 4 tabs., 3 figs.

  4. Combustion

    CERN Document Server

    Glassman, Irvin

    2008-01-01

    Combustion Engineering, a topic generally taught at the upper undergraduate and graduate level in most mechanical engineering programs, and many chemical engineering programs, is the study of rapid energy and mass transfer usually through the common physical phenomena of flame oxidation. It covers the physics and chemistry of this process and the engineering applications-from the generation of power such as the internal combustion automobile engine to the gas turbine engine. Renewed concerns about energy efficiency and fuel costs, along with continued concerns over toxic and particulate emissions have kept the interest in this vital area of engineering high and brought about new developments in both fundamental knowledge of flame and combustion physics as well as new technologies for flame and fuel control. *New chapter on new combustion concepts and technologies, including discussion on nanotechnology as related to combustion, as well as microgravity combustion, microcombustion, and catalytic combustion-all ...

  5. Combustion

    CERN Document Server

    Glassman, Irvin

    1997-01-01

    This Third Edition of Glassman's classic text clearly defines the role of chemistry, physics, and fluid mechanics as applied to the complex topic of combustion. Glassman's insightful introductory text emphasizes underlying physical and chemical principles, and encompasses engine technology, fire safety, materials synthesis, detonation phenomena, hydrocarbon fuel oxidation mechanisms, and environmental considerations. Combustion has been rewritten to integrate the text, figures, and appendixes, detailing available combustion codes, making it not only an excellent introductory text but also an important reference source for professionals in the field. Key Features * Explains complex combustion phenomena with physical insight rather than extensive mathematics * Clarifies postulates in the text using extensive computational results in figures * Lists modern combustion programs indicating usage and availability * Relates combustion concepts to practical applications.

  6. Leaching and soil/groundwater transport of contaminants from coal combustion residues

    International Nuclear Information System (INIS)

    Hjelmar, O.; Hansen, E.A.; Larsen, F.; Thomassen, H.

    1992-01-01

    In this project the results of accelerated laboratory leaching tests on coal fly ash and flue gas desulfurization (FGD) products from the spray dryer absorption process (SDA) were evaluated by comparison to the results of large scale lysimeter leaching tests on the same residues. The mobility of chromium and molybdenum - two of the kev contaminants of coal combustion residue leachates - in various typical soil types was investigated by batch and column methods in the laboratory. Some of the results were confirmed by field observations at an old coal fly ash disposal site and by a lysimeter attenuation test with coal fly ash leachate on a clayed till. A large number of groundwater transport models and geochemical models were reviewed, and two of the models (Gove-Stollenwerk and CHMTRNS) were modified and adjusted and used to simulate column attenuation tests performed in the laboratory. One of the models (Grove-Stollenwerk) was used to illustrate a recommended method of environmental impact assessment, using lysimeter leaching data and laboratory column attenuation data to describe the emission and migration of Mo from a coal fly ash disposal site

  7. Some aspects of the technology improvement for heat reprocessing of the combustible radioactive wastes and ash residue conditioning

    International Nuclear Information System (INIS)

    Dmitriev, S.A.; Lifanov, F.A.; Knyazev, I.A.; Buravchenko, N.N.; Sobolev, I.A.; Mamaev, L.A.; Alekseev, A.N.; Simagina, O.S.

    1991-01-01

    The results of studies devoted to increasing the efficiency of thermal reprocessing (combustion) of organic low- and intermediate-level radioactive wastes are given. The new most efficient three-stage process including: 1) gasification and pyrolysis of an organic material with volatile product release, 2) coke residual combustion, ash and noncombustible materials melting, 3) combustion of volatile products of thermal decomposition is developed on the basis of the analysis of solid radioactive waste combustion schemes, mathematical simulation and laboratory studies. Experimental bed, in which these processes are realized, is created. The results obtained in it have allowed one to begin designing of the pilot-commercial plant with shaft furnace having the capacity up to 200 kg/h for solid wastes

  8. Increase in efficiency and reduction of generation cost at hard coal-fired power plants. Post-combustion of combustion residues from co-firing of RDF and biomass during dry ash removal

    Energy Technology Data Exchange (ETDEWEB)

    Baur, Guenter [Magaldi Power GmbH, Esslingen (Germany); Spindeldreher, Olaf [RWE Generation SE, Werne (Germany); RWE Generation SE, Essen (Germany)

    2013-09-01

    Secondary as well as substitute fuels are being used in hard coal-fired power plants to improve efficiency and to enlarge fuel flexibility. However, grinding and firing systems of the existing coal-fired plants are not designed for those co-fuels. Any deterioration of the combustion performance would reduce the power output and increase ash disposal costs by increased content of combustion residues. The application of air-cooled ash removal, with simultaneous and controlled post-combustion of unburned residues on the conveyor belt, enlarges the furnace and maintains combustion efficiency even with different fuel qualities. Plant efficiency can also be increased through heat recovery. (orig.)

  9. Characteristics of ash and particle emissions during bubbling fluidised bed combustion of three types of residual forest biomass.

    Science.gov (United States)

    Ribeiro, João Peres; Vicente, Estela Domingos; Alves, Célia; Querol, Xavier; Amato, Fulvio; Tarelho, Luís A C

    2017-04-01

    Combustion of residual forest biomass (RFB) derived from eucalypt (Eucalyptus globulus), pine (Pinus pinaster) and golden wattle (Acacia longifolia) was evaluated in a pilot-scale bubbling fluidised bed reactor (BFBR). During the combustion experiments, monitoring of temperature, pressure and exhaust gas composition has been made. Ash samples were collected at several locations along the furnace and flue gas treatment devices (cyclone and bag filter) after each combustion experiment and were analysed for their unburnt carbon content and chemical composition. Total suspended particles (TSP) in the combustion flue gas were evaluated at the inlet and outlet of cyclone and baghouse filter and further analysed for organic and elemental carbon, carbonates and 57 chemical elements. High particulate matter collection efficiencies in the range of 94-99% were observed for the baghouse, while removal rates of only 1.4-17% were registered for the cyclone. Due to the sand bed, Si was the major element in bottom ashes. Fly ashes, in particular those from eucalypt combustion, were especially rich in CaO, followed by relevant amounts of SiO 2 , MgO and K 2 O. Ash characteristics varied among experiments, showing that their inorganic composition strongly depends on both the biomass composition and combustion conditions. Inorganic constituents accounted for TSP mass fractions up to 40 wt%. Elemental carbon, organic matter and carbonates contributed to TSP mass fractions in the ranges 0.58-44%, 0.79-78% and 0.01-1.7%, respectively.

  10. Properties of Chemically Combusted Calcium Carbide Residue and Its Influence on Cement Properties

    Directory of Open Access Journals (Sweden)

    Hongfang Sun

    2015-02-01

    Full Text Available Calcium carbide residue (CCR is a waste by-product from acetylene gas production. The main component of CCR is Ca(OH2, which can react with siliceous materials through pozzolanic reactions, resulting in a product similar to those obtained from the cement hydration process. Thus, it is possible to use CCR as a substitute for Portland cement in concrete. In this research, we synthesized CCR and silica fume through a chemical combustion technique to produce a new reactive cementitious powder (RCP. The properties of paste and mortar in fresh and hardened states (setting time, shrinkage, and compressive strength with 5% cement replacement by RCP were evaluated. The hydration of RCP and OPC (Ordinary Portland Cement pastes was also examined through SEM (scanning electron microscope. Test results showed that in comparison to control OPC mix, the hydration products for the RCP mix took longer to formulate. The initial and final setting times were prolonged, while the drying shrinkage was significantly reduced. The compressive strength at the age of 45 days for RCP mortar mix was found to be higher than that of OPC mortar and OPC mortar with silica fume mix by 10% and 8%, respectively. Therefore, the synthesized RCP was proved to be a sustainable active cementitious powder for the strength enhanced of building materials, which will result in the diversion of significant quantities of this by-product from landfills.

  11. Properties of Chemically Combusted Calcium Carbide Residue and Its Influence on Cement Properties.

    Science.gov (United States)

    Sun, Hongfang; Li, Zishanshan; Bai, Jing; Memon, Shazim Ali; Dong, Biqin; Fang, Yuan; Xu, Weiting; Xing, Feng

    2015-02-13

    Calcium carbide residue (CCR) is a waste by-product from acetylene gas production. The main component of CCR is Ca(OH)₂, which can react with siliceous materials through pozzolanic reactions, resulting in a product similar to those obtained from the cement hydration process. Thus, it is possible to use CCR as a substitute for Portland cement in concrete. In this research, we synthesized CCR and silica fume through a chemical combustion technique to produce a new reactive cementitious powder (RCP). The properties of paste and mortar in fresh and hardened states (setting time, shrinkage, and compressive strength) with 5% cement replacement by RCP were evaluated. The hydration of RCP and OPC (Ordinary Portland Cement) pastes was also examined through SEM (scanning electron microscope). Test results showed that in comparison to control OPC mix, the hydration products for the RCP mix took longer to formulate. The initial and final setting times were prolonged, while the drying shrinkage was significantly reduced. The compressive strength at the age of 45 days for RCP mortar mix was found to be higher than that of OPC mortar and OPC mortar with silica fume mix by 10% and 8%, respectively. Therefore, the synthesized RCP was proved to be a sustainable active cementitious powder for the strength enhanced of building materials, which will result in the diversion of significant quantities of this by-product from landfills.

  12. Aceites esenciales: mitos y realidades

    OpenAIRE

    García García, Pablo

    2014-01-01

    Los aceites esenciales son mezclas complejas de compuestos volátiles extraídos de plantas olorosas. Estos compuestos son utilizados por las plantas para su desarrollo, reproducción o protección. Los aceites esenciales han sido utilizados desde la antigüedad con fines bactericidas, antiparasitarios, insecticidas, medicinales y cosméticos y en la actualidad se usan en la industria farmacéutica, cosmética, agrícola y alimentaria.

  13. Chemical composition of leachate of dairy manure mixed with fluidized bed combustion residue

    Energy Technology Data Exchange (ETDEWEB)

    Elrashidi, M.A.; Baligar, V.C.; Korcak, R.F.; Persaud, N.; Ritchey, K.D. [USDA-ARS-ASWCRL, Beaver, WV (United States)

    1999-07-01

    This study was initiated to investigate the hypothesis that using Fluidized Bed Combustion (FBC) residue to stabilize a dairy feedlot surface (DFS) could enhance element attenuation and minimize the environmental impact on water quality. The laboratory leaching experiment included FBC, dairy manure (DM), and DM/FBC treatments. The leaching process consisted of 10 weekly additions of distilled water, each of 460 mL. Using FBC with DM decreased the concentration of most elements (e.g., P. N, K, Ca, Al, Si, Fe, Mn, Cu, Zn, Pb, Cd, Co, Cr, Ni, As and Se) in the leachate. A decrease ranging from 5.6 to 100% was obtained. The presence of high concentration of dissolved organic matter (DOM) is believed to enhance element attenuation by FBC minerals (e.g., Fe-, and Al-oxides). Several mechanisms involved in this process are proposed: (1) formation of insoluble metal-organic complexes; (2) sorption of soluble organic and inorganic species on mineral surfaces; and (3) precipitation of soluble inorganic species. These mechanisms are discussed in relation to each of the measured elements. On the other hand, using FBC with DM appeared to increase the concentration of B (235%), S (47.3%), and Mg (36.5%) in the leachate. Reactions of DM with FBC minerals to form soluble organic complexes were suggested to explain B and S increases. The increase in leached Mg could be attributed to the presence of SO{sub 4}{sup 2-}. The results provide evidence that using FBC to stabilize DFS has the advantage of immobilizing a large portion of most elements present in DM leachate. 41 refs., 3 figs., 2 tabs.

  14. Chemical composition of leachate of dairy manure mixed with fluidized bed combustion residue

    Energy Technology Data Exchange (ETDEWEB)

    Elrashidi, M.A.; Baligar, V.C.; Korcak, R.F.; Persaud, N.; Ritchey, K.D.

    1999-08-01

    This study was initiated to investigate the hypothesis that using fluidized bed combustion (FBC) residue to stabilize a dairy feedlot surface (DFS) could enhance element attenuation and minimize the environmental impact on water quality. The laboratory leaching experiment included FBC, dairy manure (DM), and DM/FBC treatments. The leaching process consisted of 10 weekly additions of distilled water, each of 460 mL. Using FBC with DM decreased the concentration of most elements (e.g., P, N, K, Ca, Al, Si, Fe, Mn, Cu, Zn, Pb, Cd, Co, Cr, Ni, As, and Se) in the leachate. A decrease ranging from 5.6 to 100% was obtained. The presence of high concentration of dissolved organic matter (DOM) is believed to enhance element attenuation by FBC minerals. Several mechanisms involved in this process are proposed: (1) formation of insoluble metal-organic complexes; (2) sorption of soluble organic and inorganic species on mineral surfaces; and (3) precipitation of soluble inorganic species. These mechanisms are discussed in relation to each of the measured elements. On the other hand, using FBC with DM appeared to increase the concentration of B, S, and Mg in the leachate. Reactions of DOM with FBC minerals to form soluble organic complexes were suggested to explain B and S increases. The increase in leached Mg could be attributed to the presence of SO{sub 4}{sup 2{minus}}. Their results provide evidence that using FBC to stabilize DFS has the advantage of immobilizing a large portion of most elements present in DM leachate.

  15. Quality of diets with fluidized bed combustion residue treatment: I. Rat trials

    Energy Technology Data Exchange (ETDEWEB)

    Cahill, N.J.; Reid, R.L.; Head, M.K.; Hern, J.L.; Bennett, O.L.

    Feeding trials were conducted with rats (Rattus rattus) to examine effects of soil application, or dietary inclusion, of fluidized bed combustion residue (FBCR) on the composition and quality of foods. Four diets (vegetable protein, egg protein, chicken, chicken + dietary FBCR) prepared with either FBCR or lime (control) treatments, were fed to weanling, female rats in three growth and reproduction trials. Intake, growth rate, and composition of body and organs of rats were measured. Rats in one trial were bred, their litters maintained on dietary treatments, and the offspring rebred. Treatment (FBCR vs. lime) x diet interactions on food composition and animal responses generally were not significant. Treatment had little effect on element composition of diets; mineral concentrations were in normal ranges. Diet treatment with FBCR depressed (P<0.01) food intake and growth of rats in one trial, but not in others, and had no effect (P<0.05) on body water, protein, ether extract, or gross energy composition. Some differences in element concentrations in the carcass and organs of rats and pups resulted from FBCR treatment, but effects were small and inconsistent. Litters from the first reproductive cycle appeared normal, except for animals fed the chicken + dietary FBCR treatment, on which pups showed poor growth and anemia. Offspring from certain diets were rebred and litters showed a high mortality, although this was not associated specifically with FBCR treatment. Results indicated no major detrimental effects on food composition, or growth, tissue element accumulation, and reproduction in the rat relating to use of FBCR as a soil amendment. 20 refs., 9 tabs.

  16. Quality of diets with fludized bed combustion residue treatment: II. Swine trials

    Energy Technology Data Exchange (ETDEWEB)

    Whitsel, T.J.; Reid, R.L.; Stout, W.L.; Hern, J.L.; Bennett, O.L.

    Growing pigs (Sus scrofa domesticus) were fed for an 8-wk period in two trials on diets produced on soils treated with fluidized bed combustion residue (FBCR) or limestone. Diets contained corn (Zea mays L.) and wheat (Triticum aestivum L.) mixtures with soybean (Glycine max (L.) Merr.) meal, supplemented with vegetables, fruits, and meat. Pigs were fed ad libitum and effects of diet treatment on rate of gain, N balance, blood composition, and element composition of the carcass and organs were determined. The FBCR diet caused a decrease (P<0.05 in Trial 1, P <0.07 in Trial 2) in body weight gains of pigs, but increased (P<0.05) N retention in one trial. Blood composition was not influenced markedly by diet treatment, with small but significant differences in serum Ca, triglycerides, certain amino acids, and whole blood Pb concentrations; effects were not consistent between trials. Urinary As concentration was slightly higher for pigs on FBCR diets. Analysis of the carcass and organs of pigs slaughtered posttrial showed significant differences in element levels from those of pretrial animals, but differences in tissue mineral concentrations related to diet treatment were few and inconsistent. Element concentrations in the organs of pigs were within normal ranges. No explanation for the depression in weight gain of pigs fed FBCR-treated diets was found. Except for the weight response, results support data from other trials with laboratory animals showing no apparent adverse effects of FBCR application to soils on nutritive quality of foods. 24 refs., 1 fig., 10 tabs.

  17. Naturally Occurring Radioactive Materials in Uranium-Rich Coals and Associated Coal Combustion Residues from China.

    Science.gov (United States)

    Lauer, Nancy; Vengosh, Avner; Dai, Shifeng

    2017-11-21

    Most coals in China have uranium concentrations up to 3 ppm, yet several coal deposits are known to be enriched in uranium. Naturally occurring radioactive materials (NORM) in these U-rich coals and associated coal combustion residues (CCRs) have not been well characterized. Here we measure NORM (Th, U, 228 Ra, 226 Ra, and 210 Pb) in coals from eight U-rich coal deposits in China and the associated CCRs from one of these deposits. We compared NORM in these U-rich coals and associated CCRs to CCRs collected from the Beijing area and natural loess sediments from northeastern China. We found elevated U concentrations (up to 476 ppm) that correspond to low 232 Th/ 238 U and 228 Ra/ 226 Ra activity ratios (≪1) in the coal samples. 226 Ra and 228 Ra activities correlate with 238 U and 232 Th activities, respectively, and 226 Ra activities correlate well with 210 Pb activities across all coal samples. We used measured NORM activities and ash yields in coals to model the activities of CCRs from all U-rich coals analyzed in this study. The activities of measured and modeled CCRs derived from U-rich coals exceed the standards for radiation in building materials, particularly for CCRs originating from coals with U > 10 ppm. Since beneficial use of high-U Chinese CCRs in building materials is not a suitable option, careful consideration needs to be taken to limit potential air and water contamination upon disposal of U- and Ra-rich CCRs.

  18. Thermogravimetric analysis of the behavior of sub-bituminous coal and cellulosic ethanol residue during co-combustion.

    Science.gov (United States)

    Buratti, C; Barbanera, M; Bartocci, P; Fantozzi, F

    2015-06-01

    The influence of the addition of cellulosic ethanol residue (CER) on the combustion of Indonesian sub-bituminous coal was analyzed by non isothermal thermo-gravimetric analysis (TGA). The effect of blends ratio (5%, 10%, 15% and 20%), interaction mechanism, and heating rate (5°C/min, 10°C/min, 15°C/min, 20°C/min) on the combustion process was studied. The results show that the increase of the blending ratio allows to achieve the increase of the combustibility index from 7.49E-08 to 5.26E-07 at the blending ratio of 20%. Two types of non-isothermal kinetic analysis methods (Ozawa-Flynn-Wall and Vyazovkin) were also applied. Results indicate that the activation energy of the blends decreases with increasing the conversion rate. In particular, the blending ratio of 20% confirms to have the better combustion performance, with the average value of the activation energy equal to 41.10 kJ/mol obtained by Ozawa-Flynn-Wall model and 31.17 kJ/mol obtained by Vyazovkin model. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Estudio de la viscosidad y densidad de diferentes aceites para su uso como biocombustible

    OpenAIRE

    Legaz Berbel, Ramsés

    2010-01-01

    En este proyecto se realiza una breve introducción al mundo de las energías renovables, como alternativa muy importante al uso del petróleo. Más concretamente se explicará la importancia del uso de los biocombustibles, así como las ventajas e inconvenientes del uso de los mismos. El objetivo principal del proyecto es el uso de aceites vegetales como combustible para un motor diesel, solucionando un inconveniente, la diferencia existente entre las propiedades físicas del gasoil y los aceite...

  20. A stochastic logical system approach to model and optimal control of cyclic variation of residual gas fraction in combustion engines

    International Nuclear Information System (INIS)

    Wu, Yuhu; Kumar, Madan; Shen, Tielong

    2016-01-01

    Highlights: • An in-cylinder pressure based measuring method for the RGF is derived. • A stochastic logical dynamical model is proposed to represent the transient behavior of the RGF. • The receding horizon controller is designed to reduce the variance of the RGF. • The effectiveness of the proposed model and control approach is validated by the experimental evidence. - Abstract: In four stroke internal combustion engines, residual gas from the previous cycle is an important factor influencing the combustion quality of the current cycle, and the residual gas fraction (RGF) is a popular index to monitor the influence of residual gas. This paper investigates the cycle-to-cycle transient behavior of the RGF in the view of systems theory and proposes a multi-valued logic-based control strategy for attenuation of RGF fluctuation. First, an in-cylinder pressure sensor-based method for measuring the RGF is provided by following the physics of the in-cylinder transient state of four-stroke internal combustion engines. Then, the stochastic property of the RGF is examined based on statistical data obtained by conducting experiments on a full-scale gasoline engine test bench. Based on the observation of the examination, a stochastic logical transient model is proposed to represent the cycle-to-cycle transient behavior of the RGF, and with the model an optimal feedback control law, which targets on rejection of the RGF fluctuation, is derived in the framework of stochastic logical system theory. Finally, experimental results are demonstrated to show the effectiveness of the proposed model and the control strategy.

  1. Fly ash classification efficiency of electrostatic precipitators in fluidized bed combustion of peat, wood, and forest residues.

    Science.gov (United States)

    Ohenoja, Katja; Körkkö, Mika; Wigren, Valter; Österbacka, Jan; Illikainen, Mirja

    2018-01-15

    The increasing use of biomasses in the production of electricity and heat results in an increased amount of burning residue, fly ash which disposal is becoming more and more restricted and expensive. Therefore, there is a great interest in utilizing fly ashes instead of just disposing of it. This study aimed to establish whether the utilization of fly ash from the fluidized bed combustion of peat, wood, and forest residues can be improved by electrostatic precipitator separation of sulfate, chloride, and some detrimental metals. Classification selectivity calculations of electrostatic precipitators for three different fuel mixtures from two different power plants were performed by using Nelson's and Karnis's selectivity indices. Results showed that all fly ashes behaved similarly in the electrostatic separation process SiO 2 resulted in coarse fractions with Nelson's selectivity of 0.2 or more, while sulfate, chloride, and the studied detrimental metals (arsenic, cadmium, and lead) enriched into fine fractions with varying selectivity from 0.2 to 0.65. Overall, the results of this study suggest that it is possible to improve the utilization potential of fly ashes from fluidized bed combustion in concrete, fertilizer, and earth construction applications by using electrostatic precipitators for the fractionating of fly ashes in addition to their initial function of collecting fly ash particles from flue gases. The separation of the finer fractions (ESP 2 and 3) from ESP 1 field fly ash is recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Environmental performance of the Kvaerner BFB boilers for MSW combustion -- Analysis of gaseous emissions and solid residues

    International Nuclear Information System (INIS)

    Lundberg, M.; Hagman, U.; Andersson, B.A.; Olofsson, J.

    1997-01-01

    Kvaerner Pulping AB (formerly Kvaerner EnviroPower AB) has, due to the stringent demands on emissions performance, developed a state-of-the-art bubbling fluidized bed boiler (BFB) designed for waste fuel firing with very low emissions to the air. A complete evaluation of the environmental performance of the Kvaerner BFB technique for MSW combustion is now possible thanks to a thorough characterization study of the solid residues from the Lidkoeping plant. This paper gives an overall mapping of the emissions performance. Data from the operating plants on solid residue characteristics and leachability, heavy metal and dioxin emissions, nitrogen oxides, carbon monoxide, acid gases, and other emissions to air are presented. Comparisons are made with legislative limits and data from the mass burning technique. It is concluded that the emissions are low compared both with data from traditional mass burn incinerators and with legislative limits in the USA and Europe. Furthermore, the bottom and cyclone ash characteristics are shown not to cause any particular problem from an environmental point of view, and that the leachability is well below the existing legislative limits in Europe and the USA. The results show that fluidized bed combustion of municipal solid waste is a very competitive alternative to the traditional mass burning technique in every respect

  3. Energy Generation from Horse Husbandry Residues by Anaerobic Digestion, Combustion, and an Integrated Approach

    Directory of Open Access Journals (Sweden)

    Meike Nitsche

    2017-02-01

    Full Text Available Horse-related activities often occur close to urban areas, where acreage for horse manure disposal is scarce, and subsequently alternative recovery options are necessary. Anaerobic digestion, direct combustion, and the integrated generation of solid fuel and biogas from biomass (IFBB process are potential techniques focusing on energy provision. In this study, samples of horse faeces were analysed for chemical composition as pure feedstock and in mixture with straw or wood shavings, as well as for energy yield by biogas production or from combustion of solid fuel. It was observed that chemical properties of faeces, in a mixture with wood shavings, were promising for direct combustion, but achieved low methane yields. The methane yield of pure faeces and the straw mixture was 222.33 ± 13.60 and 233.01 ± 31.32 lN·kg-1 volatile solids (VSadded, respectively. The IFBB process divided the biomass into a press cake with reduced mineral concentration and a press fluid. Methane yields of press fluids were low (108.2 lN·kg-1 VSadded, on average. The chemical composition of the press cake allowed for combustion and led to a higher gross energy potential than anaerobic digestion (two-fold higher for pure manure and the mixture with straw, and five-fold higher for the mixture with shavings. Consequently, the gross energy potential of IFBB is higher compared to anaerobic digestion, however it should be noted that local conditions might favour the implementation of anaerobic digestion.

  4. The use of sewage sludge as additive to avoid operational problems at combustion of shredder residues

    International Nuclear Information System (INIS)

    Gyllenhammar, Marianne

    2010-01-01

    When shredder light fraction (SLF) from recovery of metal scrap is energy recovered it is usually mixed with more than 90% of other wastes. SLF is a fuel with high energy content but also with relatively high chlorine and metal content and could cause deposit and corrosion problems in incineration plants. Sewage sludge has previously been shown to reduce deposition and corrosion problems in combustion of alkali and chlorine containing biomass. In this work 20 % SLF (by energy content) has been combusted together with municipal solid waste and industrial wastes, with and without addition of 3 % (by energy content) sewage sludge. The initial fireside corrosion rate was then compared to the corrosion rate during combustion of the normal fuel mix, i.e. only municipal solid waste and industrial wastes. The tests were done at the 20 MW fluidized bed boiler of Lidkoping heat production plant. During the tests air-cooled corrosion and deposit probes were exposed for 24 hours. Deposit probes were placed at three different flue gas temperatures - in the combustion chamber, upstream and downstream the convection pass. The corrosion probes were placed upstream the convection pass and on the probes there were three different materials at three different water temperatures (280, 350 and 420 degree Celsius). The tests showed that sewage sludge could help avoiding deposition and corrosion problems when incinerating SLF. The amount of deposits was reduced and the content of the deposits was less corrosive when sewage sludge was added. The project was financed by Waste Refinery as a collaboration project between Stena Metall AB, Metso AB, High Temperature Corrosion Center at Chalmers University of Technology, SP Technical Research Institute of Sweden and Lidkopings Varmeverk. (author)

  5. Simulación CFD de la transferencia de calor en un reactor de hidrotratamiento de aceites vegetales de segunda generación

    OpenAIRE

    Mendoza Sépulveda, César Camilo

    2013-01-01

    Resumen: Se desarrolló un modelo CFD que permite representar la transferencia de calor en un reactor de hidrotratamiento de aceites vegetales. Este modelo permitió evaluar la transferencia de calor para distintas configuraciones del reactor. En el proceso de hidrotratamiento de aceites vegetales se transforma el aceite en un líquido con cero contenido de azufre y excelentes propiedades como combustible diesel. El proceso se basa en la adición de hidrógeno a alta presión en un reactor de lecho...

  6. Vitamina E y aceites vegetales

    Directory of Open Access Journals (Sweden)

    Morales, M. T.

    2007-03-01

    Full Text Available An interest in vitamin E has increased in recent years due to its potent antioxidant properties and its role in preventing age-related diseases, cardiovascular diseases or Alzheimer. This work describes the biogenesis, bioavailability, nutritional requirements, activity and properties of vitamin E. Vegetable oils constitute one of the main sources of vitamin E dietary intake and an extensive bibliographic revision of this vitamin in vegetable oils is carried out from four points of view: antioxidant properties, health benefits, effects of external agents and effects of processing on vitamin E content and analytical techniques used for its analysis.El interés por la vitamina E ha aumentado en los últimos años debido a su potente poder antioxidante y a su papel frente a enfermedades relacionadas con la edad, trastornos cardiovasculares o Alzheimer. En este trabajo se detallan la biogénesis, biodisponibilidad, requerimientos nutricionales, actividad y propiedades de la vitamina E. Los aceites vegetales constituyen una de las fuentes principales de aporte de vitamina E a través de la dieta, por lo que se lleva a cabo una amplia revisión bibliográfica desde cuatro puntos de vista: vitamina E y propiedades antioxidantes, beneficios para la salud debidos a la ingestión de aceites vegetales, efecto de agentes externos y procesado sobre el contenido de vitamina E y técnicas analíticas utilizadas para su análisis.

  7. Contamination Detection and Mitigation Strategies for Unsymmetric Dimethylhydrazine/Nitrogen Tetroxide Non-Combustion Product Residues

    Science.gov (United States)

    Greene, Benjamin; Buchanan, Vanessa D.; Baker, David L.

    2006-01-01

    Dimethylamine and nitrite, which are non-combustion reaction products of unsymmetrical dimethylhydrazine (UDMH) and nitrogen tetroxide (NTO) propellants, can contaminate spacesuits during extra-vehicular activity (EVA) operations. They can react with water in the International Space Station (ISS) airlock to form N-nitrosodimethylamine (NDMA), a carcinogen. Detection methods for assessing nitrite and dimethylamine contamination were investigated. The methods are based on color-forming reactions in which intensity of color is proportional to concentration. A concept color detection kit using a commercially available presumptive field test for methamphetamine coupled with nitrite test strips was developed and used to detect dimethylamine and nitrite. Contamination mitigation strategies were also developed.

  8. Recovery of Trace and Heavy Metals from Coal Combustion Residues for Reuse and Safe Disposal: A Review

    Science.gov (United States)

    Kumar, Ashvani; Samadder, Sukha Ranjan; Elumalai, Suresh Pandian

    2016-09-01

    The safe disposal of coal combustion residues (CCRs) will remain a major public issue as long as coal is used as a fuel for energy production. Both dry and wet disposal methods of CCRs create serious environmental problems. The dry disposal method creates air pollution initially, and the wet disposal method creates water pollution as a result of the presence of trace and heavy metals. These leached heavy metals from fly ash may become more hazardous when they form toxic compounds such as arsenic sulfite (As2S3) and lead nitrate (N2O6Pb). The available studies on trace and heavy metals present in CCRs cannot ensure environmentally safe utilization. In this work, a novel approach has been offered for the retrieval of trace and heavy metals from CCRs. If the proposed method becomes successful, then the recovered trace and heavy metals may become a resource and environmentally safe use of CCRs may be possible.

  9. Investigation on the fast co-pyrolysis of sewage sludge with biomass and the combustion reactivity of residual char.

    Science.gov (United States)

    Deng, Shuanghui; Tan, Houzhang; Wang, Xuebin; Yang, Fuxin; Cao, Ruijie; Wang, Zhao; Ruan, Renhui

    2017-09-01

    Gaining the valuable fuels from sewage sludge is a promising method. In this work, the fast pyrolysis characteristics of sewage sludge (SS), wheat straw (WS) and their mixtures in different proportions were carried out in a drop-tube reactor. The combustion reactivity of the residual char obtained was investigated in a thermogravimetric analyzer (TGA). Results indicate that SS and WS at different pyrolysis temperatures yielded different characteristic gas compositions and product distributions. The co-pyrolysis of SS with WS showed that there existed a synergistic effect in terms of higher gas and bio-oil yields and lower char yield, especially at the WS adding percentage of 80wt%. The addition of WS to SS increased the carbon content in the SS char and improved char porous structures, resulting in an improvement in the combustion reactivity of the SS char. The research results can be used to promote co-utilization of sewage sludge and biomass. Copyright © 2017. Published by Elsevier Ltd.

  10. Solid-state nuclear magnetic resonance studies of phosphorus and boron in coals and combustion residues

    Energy Technology Data Exchange (ETDEWEB)

    Burchill, P.; Howarth, O.W.; Richards, D.G.; Sword, B.J. (British Coal Corporation, Stoke Orchard (UK). Coal Research Establishment)

    1990-04-01

    Solid-state nuclear magnetic resonance spectroscopy with magic angle spinning (MAS-n.m.r.) was used to study the occurrence of phosphorus and boron in coal, and their fate on combustion. These elements are only minor components of coal, but may significantly influence the utilization properties. {sup 31} P MAS-n.m.r. spectroscopy has confirmed that phosphorus is present in coal predominantly as apatite. This mineral is thermally stable under oxidizing conditions, and survives largely unaltered in high temperature ashes. However, under the semi-reducing bed conditions of certain stoker-fired boilers, it may be decomposed, volatilizing the phosphorus. The {sup 31}P MAS-n.m.r. spectra of bonded deposits show phosphorus in a markedly different coordination environment to that in apatite, the chemical shift suggesting aluminium phosphate or boron phosphate. {sup 11}B MAS-n.m.r. spectra of coals exhibit resonances due to both trigonal and tetrahedrally coordinated boron. Trigonal boron is probably present as tourmaline, but the nature of the tetrahedral boron is less certain; it may be held in tetrahedral sites within certain clay minerals. In common with phosphorus, boron may be volatilized during combustion. The {sup 11}B MAS-n.m.r. spectra of bonded deposits show a tetrahedral resonance with a chemical shift quite consistent with that of boron phosphate. 39 refs., 9 figs., 5 tabs.

  11. PROPUESTA DE MINIMIZACIÓN DEL IMPACTO AMBIENTAL PRODUCIDO POR VERTIDOS DE ACEITES VEGETALES USADOS

    Directory of Open Access Journals (Sweden)

    Héctor Chamorro

    2006-04-01

    Full Text Available Este artículo Desarrolla una propuesta para minimizar el impacto ambiental producido por los vertidos de los aceites vegetales usados (AVU a las redes de aguas de desecho municipales, vertederos, rellenos sanitarios, cuerpos de aguas naturales. . Se determinó y cuantificó el universo de potenciales suplidores de aceites vegetales usados en la ciudad de Puerto Ordaz, Con los AVU se producirá un combustible ecológico, a través de la transesterificación de esteres. Se diseño y construyo una planta piloto para estudiar las reacciones químicas involucradas en el proceso y la producción del combustible ecológico (BIODIESEL, que podrá ser utilizado en cualquier motor Diesel.

  12. Evaluating the thermal stability of mercury and other metals in coal combustion residues used in the production of cement clinker, asphalt, and wallboard

    Science.gov (United States)

    Research is underway by the U.S. Environmental Protection Agency (EPA) to document any changes that may occur to coal combustion residues (CCRs) as a result of implementation of mercury and multiipollutant control technology at coal-fired power plants. This work was cited as a pr...

  13. Valorization of lignite combustion residues and ferroalumina in the production of aggregates.

    Science.gov (United States)

    Anagnostopoulos, I M; Stivanakis, V E; Angelopoulos, G N; Papamantellos, D C

    2010-02-15

    The present research study investigates the synergy of industrial solid by-products from lignite combustion (fly ash and bottom ash) and aluminum production (ferroalumina) in the production of lightweight aggregates (LWA). The process consists of two stages, pelletization and sintering. Bottom ash (BA) is used as the principal raw material in mixtures while ferroalumina (FAL) is added in lower percentages (5-30 wt%). BA carbon content is used as the fuel of sintering process in high temperatures, around 1250 degrees C, and gas generation is responsible for porous structure formation. Physical properties such as porosity, water absorption and bulk density, of sintering products are measured. Increase of FAL percentage in sintering mixtures results in decrease of porosity from 61% to 35% and of water absorption from 61% to 21% and in increase of bulk density from 1.02 g/cm(3) to 1.80 g/cm(3) of the produced aggregates. Aggregates produced by FAL addition up to 20 wt% are characterized as LWA. Aggregates formed are used in the production of concrete specimens. Compressive strength of concrete increases by increasing FAL addition in aggregates from 5 wt% to 15 wt% (highest strength value), while decrease by increasing FAL addition from 20 wt% to 30 wt%. FAL addition in lignite ashes sintering mixtures (up to 15 wt%) is considered as an important parameter for enhancing aggregates strength.

  14. Potencial para el uso directo de los aceites vegetales en los motores de combustión

    OpenAIRE

    Ortiz Laurel, Hipólito; Rössel Kipping, Dietmar; Schümann, Ulrike

    2012-01-01

    Los combustibles fósiles son aquellos que provienen de restos orgánicos vegetales y animales y se extraen de la naturaleza. Estos combustibles son contaminantes del medio ambiente a través de los gases que salen de los motores de combustión. El biodiesel es un combustible de origen vegetal obtenido a partir de los aceites vegetales de semillas, plantas y algas oleaginosas. El biodiesel es menos contaminante que los combustibles fósiles. Este trabajo presenta una revisión de las propiedades en...

  15. Desarrollo y validación de una metodología para la determinación de residuos de orto-fenilfenol en aceite esencial de frutas cítricas en Tucumán, R. Argentina Development and validation of a methodology for determining orto-phenylphenol residues in citrus essential oil in Tucumán, Argentina

    Directory of Open Access Journals (Sweden)

    Norma Kamiya

    Full Text Available Los aceites esenciales de frutas cítricas constituyen mezclas complejas de compuestos orgánicos que interfieren en la cuantificación de residuos de plaguicidas. Siendo escasa la bibliografía encontrada para la determinación de orto-fenilfenol (OPP en estas matrices, este trabajo apunta a adaptar, desarrollar, validar y acreditar bajo Norma IRAM 301 (ISO/IEC 17025:2005, un método sencillo y de menor costo. Para dicha cuantificación, se tomaron como punto de partida metodologías aplicadas al análisis de frutas cítricas y se aprovechó el carácter ácido del OPP para separarlo mediante una extracción ácido-base. Posteriormente, fue detectado y cuantificado por cromatografía gaseosa (CG con detector de ionización de llama (FID. Se obtuvieron recuperaciones promedio de 89% a 104%, en el rango de 0,1 a 100 mg/kg, para aceite esencial de limón (AEL; de 93% a 103 % y de 90% a 114% entre 0,2 mg/kg y 10 mg/kg de OPP para aceite esencial de pomelo (AEP blanco y rosado, respectivamente. Los límites de detección fueron 0,05 mg/kg para AEL y 0,1 mg/kg para AEP blanco y rosado. Los límites de cuantificación fueron 0,1 mg/kg para AEL y 0,2 mg/kg para AEP. Además, se observaron una linealidad aceptable en los rangos evaluados e incertidumbres relativas de 24% para AEL, 14% para AEP blanco y 23% para AEP rosado.The essential oils of citric fruits constitute complex mixtures of organic compounds which interfere with pesticide residues quantitation. As there exists scarce bibliography on ortho-phenylphenol (OPP determination in this commodity, the present work aims to adapt, develop and validate a simple and cheaper method for determining phenylphenol residues in citrus essential oil, while certifying it under IRAM 301 standard (ISO/IEC 17025:2005. Citrus fruit analysis methods were used, taking advantage of OPP acidity for its extraction from the commodity by simple acid-base extraction. Later, gas chromatography with flame ionization detector

  16. Emission factors of polycyclic and nitro-polycyclic aromatic hydrocarbons from residential combustion of coal and crop residue pellets.

    Science.gov (United States)

    Yang, Xiaoyang; Liu, Shijie; Xu, Yisheng; Liu, Yu; Chen, Lijiang; Tang, Ning; Hayakawa, Kazuichi

    2017-12-01

    Polycyclic aromatic hydrocarbons (PAHs) and nitro-polycyclic aromatic hydrocarbons (NPAHs) are toxic pollutants mainly produced during fossil fuel combustion. Domestic coal stoves, which emit large amounts of PAHs and NPAHs, are widely used in the Chinese countryside. In this study, emission factors (Efs) for 13 PAH species and 21 NPAH species for four raw coal (three bituminous and one anthracite), one honeycomb briquette, and one crop residue pellet (peanut hulls) samples burned in a typical Chinese rural cooking stove were determined experimentally. The PAH and NPAH Efs for the six fuels were 3.15-49 mg/kg and 0.32-100 μg/kg, respectively. Peanut hulls had very high Efs for both PAHs and NPAHs, and honeycomb briquettes had the lowest Efs. 2-Nitropyrene and 2-nitrofluoranthene, which are NPAHs typically found in secondary organic aerosol, were detected in the emissions from some fuels, suggesting that chemical reactions may have occurred in the dilution tunnel between the flue gas leaving the stove and entering the sampler. The 1-nitropyrene to pyrene diagnostic ratios for coal and peanut hulls were 0.0001 ± 0.0001 and 0.0005, respectively. These were in the same order of magnitude as reference ratios for emissions during coal combustion. The 6-nitrobenzo[a]pyrene to benzo[a]pyrene ratios for the fuels were determined, and the ratios for coal and peanut hulls were 0.0010 ± 0.0001 and 0.0014, respectively. The calculated potential toxic risks indicated that peanut hull emissions were very toxic, especially in terms of NPAHs, compared with emissions from the other fuels. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Diseño del proceso de producción del biodiesel a partir de aceites de fritura

    OpenAIRE

    Bulla Pereira, Edwin Alberto

    2014-01-01

    Desde años anteriores el biodiesel se ha convertido en una de las energías alternativas potenciales para remplazar el diesel derivado del petróleo. Es un combustible amigable con el medio ambiente, sin embargo, el uso de aceites vegetales refinados para la producción de biodiesel es poco práctico y rentable. Aceites de cocina usados de fritura (AUF), puede ser una buena opción, no obstante el contenido de ácidos grasos libres (AGL), se ha convertido en el principal inconveniente para el emple...

  18. Computational fluid dynamics (CFD) analysis of the combustion process of a leather residuals gasification fuel gas: influence of fuel moisture content

    Energy Technology Data Exchange (ETDEWEB)

    Antonietti, Anderson Jose; Beskow, Arthur Bortolin; Silva, Cristiano Vitorino da [Universidade Regional Integrada do Alto Uruguai e das Missoes (URI), Erechim, RS (Brazil)], E-mails: arthur@uricer.edu.br, mlsperb@unisinos.br; Indrusiak, Maria Luiza Sperb [Universidade do Vale do Rio dos Sinos (UNISINOS), Sao Leopoldo, RS (Brazil)], E-mail: cristiano@uricer.edu.br

    2010-07-01

    This work presents a numerical study of the combustion process of leather residuals gasification gas, aiming the improvement of the process efficiency, considering different concentrations of water on the gas. The heating produced in this combustion process can be used to generation of thermal and/or electrical energy, for use at the leather industrial plant. However, the direct burning of this leather-residual-gas into the chambers is not straightforward. The alternative in development consists in processing this leather residuals by gasification or pyrolysis, separating the volatiles and products of incomplete combustion, for after use as fuel in a boiler. At these processes, different quantities of water can be used, resulting at different levels of moisture content in this fuel gas. This humidity can affect significantly the burning of this fuel, producing unburnt gases, as the carbon monoxide, or toxic gases as NOx, which must have their production minimized on the process, with the purpose of reducing the emission of pollutants to the atmosphere. Other environment-harmful-gases, remaining of the chemical treatment employed at leather manufacture, as cyanide, and hydrocarbons as toluene, must burn too, and the moisture content has influence on it. At this way, to increase understanding of the influence of moisture in the combustion process, it was made a numerical investigation study of reacting flow in the furnace, evaluating the temperature field, the chemical species concentration fields, flow mechanics and heat transfer at the process. The commercial CFD code CFX Ansys Inc. was used. Considering different moisture contents in the fuel used on the combustion process, with this study was possible to achieve the most efficient burning operation parameters, with improvement of combustion efficiency, and reduction of environmental harmful gases emissions. It was verified that the different moisture contents in the fuel gas demand different operation conditions

  19. Growth and developmental effects of coal combustion residues on Southern Leopard Frog (Rana sphenocephala) tadpoles exposed throughout metamorphosis

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, J.D.; Peterson, V.A.; Mendonca, M.T. [Auburn University, Auburn, AL (United States). Dept. for Biological Science

    2008-09-15

    The effects of aquatic deposition of coal combustion residues (CCRs) on amphibian life histories have been the focus of many recent studies. In summer 2005, we raised larval Southern Leopard Frogs, Rana sphenocephala, on either sand or CCR substrate (approximately 1 cm deep within plastic bins) and documented effects of sediment type on oral disc condition, as well as time to, mass at, and total body length at key developmental stages, including metamorphosis (Gosner stages (GS) 37, 42, and 46). We found no significant difference in mortality between the two treatments and mortality was relatively low (eight of 48 in the control group and four of 48 in the CCR group). Ninety percent of exposed tadpoles displayed oral disc abnormalities, while no control individuals displayed abnormalities. Tadpoles raised on CCR-contaminated sediment had decreased developmental rates and weighed significantly less at all developmental stages, on average, when compared to controls. The CCR treatment group was also significantly shorter In length than controls at the completion of metamorphosis (GS 46). Collectively, these findings are the most severe sub-lethal effects noted for any amphibian exposed to CCRs to date. More research is needed to understand how these long term effects may contribute to the dynamics of local amphibian populations.

  20. The effect of low-NOx combustion on residual carbon in fly ash and its adsorption capacity for air entrainment admixtures in concrete

    DEFF Research Database (Denmark)

    Pedersen, Kim Hougaard; Jensen, Anker Degn; Dam-Johansen, Kim

    2010-01-01

    been combusted in an entrained flow reactor to test the impact of changes in operating conditions and fuel type on the AEA adsorption of ash and NOx formation. Increased oxidizing conditions, obtained by improved fuel-air mixing or higher excess air, decreased the AEA requirements of the produced ash......Fly ash from pulverized coal combustion contains residual carbon that can adsorb the air-entraining admixtures (AEAs) added to control the air entrainment in concrete. This is a problem that has increased by the implementation of low-NOx combustion technologies. In this work, pulverized fuel has...... by up to a factor of 25. This was due to a lower carbon content in the ash and a lower specific AEA adsorptivity of the carbon. The latter was suggested to be caused by changes in the adsorption properties of the unburned char and a decreased formation of soot, which was found to have a large AEA...

  1. PRODUCCIÓN DE ELECTRICIDAD EN CELDAS DE COMBUSTIBLE MICROBIANAS UTILIZANDO AGUA RESIDUAL: EFECTO DE LA DISTANCIA ENTRE ELECTRODOS

    Directory of Open Access Journals (Sweden)

    Germán Buitrón

    2011-01-01

    Full Text Available Se evaluó la influencia de la separación de electrodos sobre la producción de electricidad y la eliminación de materia orgánica en celdas de combustible microbianas usando agua residual. Para ello se construyeron tres celdas de geometría semejante pero con diferente volumen. En promedio, se obtuvo una eficiencia de eliminación de materia orgánica del 71%. La duración del ciclo fue de 0.97 días para la celda de 40 mL, 1.03 días para la celda de 80 mL y 5.93 días para la celda de 120 mL. El aumento de distancia entre los electrodos (4, 8 y 12 cm no causó un efecto negativo en la generación de electricidad, pues en la mayor separación (celda de 120 mL se alcanzó un voltaje máximo de 660 mV, mientras que para las celdas de 40 y 80 mL fue de 540 mV y 532 mV, respectivamente. La densidad de potencia máxima se presentó en la celda con separación de 12 cm (408 mW/m2. Sin embargo, se observó que la potencia volumétrica disminuyó a medida que aumentó la separación entre los electrodos.

  2. Empleo de aceites esenciales como antioxidantes naturales

    Directory of Open Access Journals (Sweden)

    Zydgalo, J. A.

    1995-10-01

    Full Text Available The aims of this study were to determine and compare the antioxidant effect of essential oils from Thymus vulgaris, Laurus nobilis, Foeniculum vulgare, Eucalyptus globules, Tagetes minuta, Satureja parvifolia and Lippia polystachya in soybean oil. The concentrations of volatile oils in soybean oil were 0.1% and 0.02%. The antioxidant activity was measured by peroxide values. Thymus vulgaris and L. nobilis essential oils exhibited a significant antioxidant activity, followed by F. vulgare and E. globules in a decreasing order. Tagetes minuta, S. parvifolia and L. polystachya had not effect, and their contribution to the stability of soybean oil was negligible.

    Los objetivos de este estudio fueron determinar y comparar el efecto antioxidante de los aceites esenciales de Thymus vulgaris, Laurus nobilis, Foeniculum vulgare, Eucalyptus globulus, Tagetes minuta, Satureja parvifolia y Lippia polystachya en el aceite de soja. Las concentraciones de las esencias en el aceite de soja fueron 0.1% y 0.02%. La actividad antioxidante fue medida por los valores de peróxido. Los aceites esenciales de T. vulgaris y L nobilis exhibieron una significativa acción antioxidante seguidos, en orden decreciente, por F. vulgare y E. globulus. Las esencias de T. minuta, S. parvifolia y L polystachya no mostraron efecto antioxidante y su contribución a la estabilidad oxidativa del aceite de soja fue despreciable.

  3. Elemental analysis of ash residue from combustion of CCA treated wood waste before and after electrodialytic extraction

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; Ottosen, Lisbeth M.

    2006-01-01

    Element distribution in a combined fly ash and bottom ash from combustion of copper chromate arsenate (CCA) treated wood waste was investigated by scanning electron microscopy (SEM/EDX) before and after electrodialytic extraction. The untreated ash contained various particles, including pieces...... of incompletely combusted wood rich in Cr and Ca, and irregular particles rich in Si, Al and K. Cr was also found incorporated in silica-based matrix particles. As was associated with Ca in porous (char) particles, indicating that Ca-arsenates had been formed during combustion. Cu was associated with Cr...... in the incompletely combusted wood pieces and was also found in almost pure form in a surface layer of some matrix particles – indicating surface condensation of volatile Cu species. In treated ash, Ca and As were no longer found together, indicating that Ca-arsenates had been dissolved due to the electrodialytic...

  4. Effect of torrefaction pre-treatment on physical and combustion characteristics of biomass composite briquette from rice husk and banana residue

    Directory of Open Access Journals (Sweden)

    Amira Atan Nor

    2018-01-01

    Full Text Available Biomass is an alternative renewable energy sources that can generates energy almost same as fossil fuel. The depletion sources of fossil fuel had increase the potential use of biomass energy. In Malaysia, rice husk and banana residues are abundantly left and not treated with proper disposal method which later may contribute to environment and health problems. Thus the development of biomass composite briquette made from rice husk and banana residue is one of the potential ways to reduce the problems and hence may contribute the better way to treat the waste by recycling the waste into a form of biomass product. The biomass briquettes are used for thermal applications because it can produce a complete combustion as it has a consistent quality and high burning efficiency. However, the quality of the biomass briquette can be added by application of torrefaction pre-treatment method. Torrefaction is a thermal method that can produce more high quality of the briquette with high calorific value, high fixed carbon content, low volatile matter, and low ash content. This study was conducted to assess the physical and combustion characteristic of the biomass briquette from rice husk and banana residue which was produced through torrefaction process. The biomass briquette, were densified by using hot press machine with temperature of 180°C for about 30 minutes. The briquette produce are 150 μm in particle size with varies in mixing ratio of rice husk to banana residue which are 100:0, 80:20 and 60:40. After the briquetting process, the biomass fuel briquettes have been undergoes parameter testing and the data have been analysed. Result showed the best biomass briquette is developed from torrefied rice husk and banana residue mixed at ratio of 60:40. Moreover, SEM image reveal that torrefaction pre-treatment has shrinkage the fibres size which confirming the thermal stability of the briquette.

  5. Comments on the note by L.S. Nelson: ''unusually high (oxidizer/Pu) ratios in the macro-residues from plutonium droplet combustion''

    International Nuclear Information System (INIS)

    Allen, M.D.; Morgan, L.G.

    1982-01-01

    An alternative explanation for unusually high ratios of oxidizers/plutonium in the residues from plutonium droplet combustion is offered in response to a note by L.S. Nelson. Two additional experiments are suggested that would be helpful in clarifying the high oxidizer/Pu ratios. The first would be to measure the true surface area for a spherule after its explosion. The second is an experiment analogous to a gas analysis experiment. The conclusion is put forth that adsorbed gases are the most likely cause of the high O/M ratios described by Nelson

  6. Predicción del efecto de la temperatura sobre la viscosidad del biodiesel de aceite de palma y sus mezclas con diesel convencional.

    OpenAIRE

    Benjumea, Pedro N; Álvarez, Ángela M; Molina, Alexandra P

    2011-01-01

    La viscosidad es una propiedad fundamental para los combustibles que se utilizan en motores de encendido por compresión o motores diesel. En este artículo se presentan correlaciones empíricas, tipo ecuación de Andrade, para predecir el efecto de la temperatura sobre la viscosidad cinemática y absoluta del biodiesel de aceite de palma. Se utilizaron tres tipos de biodiesel obtenidos a partir del aceite crudo de palma y sus fases oleína y estearina. Adicionalmente, se analiza el comportamiento ...

  7. An exploratory screening of organic substances in combustion residues; En orienterande screening av organiska aemnen i askor

    Energy Technology Data Exchange (ETDEWEB)

    Larsson, Lennart; Lind, Bo (Swedish Geotechnical Inst., Linkoeping (Sweden)); Bjurstroem, Henrik (AaF-Process, Stockholm (Sweden))

    2008-09-15

    Ash consists of the inorganic incombustible part of fuels, but it also always contains a small amount of organic matter, occurring as trace substances with concentrations in the order of mg/kg and lower. A few types of compounds are analysed comparatively frequently, e.g. PCDD/F (the so-called dioxins), but knowledge about the other organic substances is far from exhaustive. In this investigation, three ash samples have been subjected to a semi-quantitative GC/MS screening of semi-volatile substances. In this method of analysis the substances are extracted, separated in a gas chromatograph and identified as well as quantified using a mass spectrometer. Even if this type of analysis can be performed by researchers at universities, we chose to let commercial analytical laboratories do it in order to assess results from a nearly routine work. Residues from woody biofuels (recovered wood, virgin wood and bark) were chosen in order to complement the information that has previously been obtained on ash from municipal solid waste incineration. The GC/MS screening was carried out on both non-derivatised samples (non-polar compounds) and derivatised samples (polar compounds). The investigation aimed also at assessing the potential and the limitations of the screening method. In addition, the potentially hazardous properties of each identified substance were examined. Screening without and with derivatization is a cost-effective method to chart the content of semi-volatile organic substances. The results are relevant, but the method commercially available in Sweden is at present not mature enough for the use considered. It must be further developed before it can be included in e.g. regulatory texts. Limitations may be found in several steps of the method, principally: - Extraction and derivatisation, as the internal standard added is recovered only to a small extent for some ash samples, indicating that not everything has been found - Detection, i.e. both the sensitivity of

  8. Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic

    International Nuclear Information System (INIS)

    Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

    2008-01-01

    The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 deg. C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

  9. Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic.

    Science.gov (United States)

    Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

    2008-08-15

    The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 degrees C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

  10. PROCESO ENZIMATICO PARA LA PRODUCCION DE METIL ESTERES DE ACIDOS GRASOS UTILIZANDO ACEITES RESIDUALES DE FRITURA EN MEZCLA CON ACEITE DE RAPS COMO MATERIA PRIMA

    OpenAIRE

    AZOCAR ULLOA; LAURA HAYDEE; AZOCAR ULLOA; LAURA HAYDEE

    2010-01-01

    Los procesos catalizados por lipasas han sido ampliamente investigados como alternativa para la producción de metil ésteres de ácidos grasos (fatty acid methyl ester, FAME) o biodiesel. El interés en este proceso radica en que a diferencia de los procesos convencionales catalizados con sales alcalinas, los procesos catalizados con lipasas permiten el uso de materias primas alternativas y de menor costo, tales como el aceite residual de fritura (waste frying oil, WFO). Pese a los l...

  11. Exposure to coal combustion residues during metamorphosis elevates corticosterone content and adversely affects oral morphology, growth, and development in Rana sphenocephala

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, J.D.; Peterson, V.A.; Mendonca, M.T. [Auburn University, Auburn, AL (USA). Dept. of Biological Science

    2009-01-15

    Coal combustion residues (CCRs) are documented to negatively impact oral morphology, growth, and development in larval amphibians. It is currently unclear what physiological mechanisms may mediate these effects. Corticosterone, a glucocorticoid hormone, is a likely mediator because when administered exogenously it, like CCRs, also negatively influences oral morphology, growth, and development in larval amphibians. In an attempt to identify if corticosterone mediates these effects, we raised larval Southern Leopard Frogs, Rana sphenocephala, on either sand or CCR substrate and documented effects of sediment type on whole body corticosterone, oral morphology, and time to and mass at key metamorphic stages. Coal combustion residue treated tadpoles contained significantly more corticosterone than controls throughout metamorphosis. However, significantly more oral abnormalities occurred early in metamorphosis when differences in corticosterone levels between treatments were minimal. Overall, CCR-treated tadpoles took significantly more time to transition between key stages and gained less mass between stages than controls, but these differences between treatments decreased during later stages when corticosterone differences between treatments were greatest. Our results suggest endogenous increase in corticosterone content and its influence on oral morphology, growth and development is more complex than previously thought.

  12. Combustion demonstration plant in circulant fluidized bed of residual coal; Planta de Demostracion de Combustion en Lecho Fluido Circulante de Carbones Residuales

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    This report incorporates a summary of the operation results during the period of demonstration after started up. The report pretend to give an overview of the operation conditions along of the first year: Running hours, availability, electricity production, shooting downs, incidences, efficiency, fuel characteristics influence, pollutants emissions and standards comparations, etc. The main operation conclusions are: High availability, great number of running hours at full equivalent load; some months even over 100% regarding time scheduled. High reduction of gaseous emissions, really very low respecting the required by the applicable standards. It has been developed the engineering of a prototype project, by 30MW, using mixtures of solid fuels, residues and coals. (Author)

  13. Elaboración integral de las aceitunas con autogeneración de electricidad, comparada con el sistema actual de obtención del aceite de oliva virgen

    Directory of Open Access Journals (Sweden)

    Cruz Peragón, F.

    2004-09-01

    Full Text Available A future solution for treatment of the olive and obtaining olive virgin oil is presented. The energy demands for which are supplied by a generation system, that also feeds other phases of manufacture of by-products, such as "orujos" drying or extraction of the residual oil contained in them. For this purpose gasifier equipment is needed, whose major fuel is plain olive stone, although "orujos" with 20% humidity could also be used. This system produces a gas which is introduced in a combustion engine connected to a generator, harnessing the electricity created to supply the plant itself. The thermal energy surplus serves to generate and sell electrical energy to distribution grid.Se pretende plantear una solución de futuro para el proceso de elaboración de las aceitunas y obtención del aceite de oliva virgen, donde se generaría la energía eléctrica consumida en la propia planta, así como en las demás fases de elaboración completa de los subproductos, como el secado de los orujos y la extracción del aceite residual contenido en los mismos.Para esto se dimensiona un equipo gasificador del hueso, separado en el proceso de obtención indicado, con el que se abastece de energía térmica a un motor de gas que acciona un generador eléctrico, que abastece todas las necesidades de la planta integral, más el excedente de energía térmica del hueso y del orujillo resultante, generando una energía con posibilidad de venta a la red de distribución eléctrica de la zona.

  14. Guidance for classification of residues from combustion and incineration in accordance with the Swedish ordinance for waste; Vaegledning foer klassificering av foerbraenningsrester enligt Avfallsfoerordningen

    Energy Technology Data Exchange (ETDEWEB)

    Adler, Peter [AaF Energi och Miljoe AB, Stockholm (Sweden); Haglund, Jan-Erik [Soederenergi AB, Stockholm (Sweden); Sjoeblom, Rolf [Tekedo AB, Nykoeping (Sweden)

    2004-05-01

    A new ordinance for waste came into force in Sweden on the first of January 2002, replacing some previous ordinances. The new ordinance is based on certain EU directives and contains amongst other things new rules regarding how certain streams of waste are to be classified into hazardous waste and non-hazardous waste. In a number of cases, the classification is to be made according to whether or not the waste possesses one or more of a number o properties H1 - H14, i e if the waste contains hazardous substances. The new rules are based on the regulation that exists for chemical substances and preparations. When attempts have been made to use these new rules in practice - e g for residues from incineration and combustion - it has become apparent that they are very difficult or even impossible to apply. The primary reason for this is that the residues contain a very large number (thousands) of substances which would have to be analysed and for which the hazard would have to be assessed correctly in accordance with the criteria for the properties (H4 - H8 and H10 - H11). Furthermore, some of the properties listed in the ordinance for waste lack criteria for assessment of hazard. These are H13 (can give rise to another substance which may be hazardous, e g leachate) and H14 (hazardous to the environment). Moreover, there are significant differences between the Ordinance of waste and the regulation of the National Chemicals Inspectorate. It is on the latter that the rules in the Ordinance of waste are based, and this is also the cause of many of the questions and of the uncertainties in the classification. In the present report, a method is developed and described for classification of residues from combustion and incineration. The method is to be applicable in practice without compromising environmental and health aspects. As a part of the present work, a compilation of content and alteration of chemical substances in is carried out. In another chapter, the experience

  15. Field Measurements of Trace Gases and Aerosols Emitted by Undersampled Combustion Sources Including Wood and Dung Cooking Fires, Garbage and Crop Residue Burning, and Indonesian Peat Fires

    Science.gov (United States)

    Stockwell, C.; Jayarathne, T. S.; Goetz, D.; Simpson, I. J.; Selimovic, V.; Bhave, P.; Blake, D. R.; Cochrane, M. A.; Ryan, K. C.; Putra, E. I.; Saharjo, B.; Stone, E. A.; DeCarlo, P. F.; Yokelson, R. J.

    2017-12-01

    Field measurements were conducted in Nepal and in the Indonesian province of Central Kalimantan to improve characterization of trace gases and aerosols emitted by undersampled combustion sources. The sources targeted included cooking with a variety of stoves, garbage burning, crop residue burning, and authentic peat fires. Trace gas and aerosol emissions were studied using a land-based Fourier transform infrared spectrometer, whole air sampling, photoacoustic extinctiometers (405 and 870nm), and filter samples that were analyzed off-line. These measurements were used to calculate fuel-based emission factors (EFs) for up to 90 gases, PM2.5, and PM2.5 constituents. The aerosol optical data measured included EFs for the scattering and absorption coefficients, the single scattering albedo (at 870 and 405 nm), as well as the absorption Ångström exponent. The emissions varied significantly by source, although light absorption by both brown and black carbon (BrC and BC, respectively) was important for all non-peat sources. For authentic peat combustion, the emissions of BC were negligible and absorption was dominated by organic aerosol. The field results from peat burning were in reasonable agreement with recent lab measurements of smoldering Kalimantan peat and compare well to the limited data available from other field studies. The EFs can be used with estimates of fuel consumption to improve regional emissions inventories and assessments of the climate and health impacts of these undersampled sources.

  16. Scale-up study on combustibility and emission formation with two biomass fuels (B quality wood and pepper plant residue) under BFB conditions

    Energy Technology Data Exchange (ETDEWEB)

    Khan, Atif Ahmed; de Jong, Wiebren; Jansens, Peter Johannes [Department of Process and Energy, Section Energy Technology, Faculty 3ME, Delft University of Technology, Leeghwaterstraat 44, NL-2628 CA, Delft (Netherlands); Aho, Martti; Vainikka, Pasi [VTT Processes, P.O. Box 1603, 40101 Jyvaeskylae (Finland); Spliethoff, Hartmut [TU Munich, Lehrstuhl fuer Thermische Kraftanlagen, Boltzmannstrasse 15, D-85748 Garching (Germany)

    2008-12-15

    Combustion of two biomass fuels: demolition wood (DW) and pepper plant residue (PPR), was investigated from an emission viewpoint in a 20 kW{sub th} fluidized bubbling bed reactor and a 1 MW{sub th} fluidized bubbling bed test boiler. Fluidization velocity and boiler output were varied in the larger facility whereas they were kept constant in the smaller reactor. Traditional flue gases were analyzed. In addition, impactor measurements were carried out to determine the mass flow of the finest fly ash and toxic elements. These measurements were compared with EU emission directives for biomass co-incineration. It was possible to combust DW without operational problems. However, the DW was contaminated with lead, which tended to get strongly enriched in the fine fly ash. Pb tends to be adsorbed on the measurement line surfaces stronger than many other toxic elements and therefore proved difficult to collect and measure. Enrichment of Pb in the fine fly ash can be weakened by co-firing DW with PPR. Increasing the share of PPR up to 50% markedly reduces the toxic metal concentration in the finest fly ash. This, however, leads to increased mass flow of fine fly ash and increases the potential risks of operational problems such as bed agglomeration and fouling. (author)

  17. Estudio de la transformación del Aceite de Soya usado en ésteres etílicos de ácidos grasos

    OpenAIRE

    Sarracent-López, Anabel; Gandón-Hernández, José

    2016-01-01

    La reutilización de los aceites vegetales en la elaboración de alimentos trae efectos nocivos para la salud y por otro lado se necesita de un complejo tratamiento para poder descartarlos sin que afecten al medio ambiente. Transformarlo en ésteres metílicos o etílicos de ácidos graso y glicerina, mediante la transesterificación con el alcohol correspondiente, puede constituir un procedimiento adecuado para su tratamiento. Se investigó con aceite de soya residual, proveniente de una empresa pro...

  18. Los intangibles del aceite de oliva como ventaja competitiva

    OpenAIRE

    Ruiz Guerra, Ignacio; Martín López, Víctor Manuel; Molina Moreno, Valentín

    2012-01-01

    Objeto: Utilización de nuevas estrategias para el reposicionamiento del Aceite de Oliva a través de los activos intangibles. Diseño/metodología/enfoque: Aplicación del marco teórico de la intangibilidad al Aceite de Oliva y conceptualización de los activos intangibles y desarrollo de un estudio estadístico cuantitativo de valoración de los conceptos planteados. Aportaciones y resultados: Se propone una conceptualización de los activos intangibles que conforman el significado del Aceit...

  19. Kinetics of gasification and combustion of residues, biomass and coal in a bubbling fluidized bed; Die Kinetik der Vergasung und Verbrennung unterschiedlicher Abfaelle, Biomassen und Kohlen in der blasenbildenden Wirbelschicht

    Energy Technology Data Exchange (ETDEWEB)

    Hamel, S; Krumm, W [Siegen Univ. (Gesamthochschule) (Germany). Lehrstuhl fuer Energie- und Umweltverfahrenstechnik

    1998-09-01

    The combustion and gasification characteristics of Rhenish brown coal, domestic waste, waste plastics, wood and sewage sludge were investigated in a bubbling atmospheric fluidized bed in the laboratory scale. The materials were pyrolyzed in the fluidized bed in a nitrogen atmosphere. The residual coke was combuted in the presence of oxygen with varying operating parameters or else gasified in the presence of carbon dioxide. The different materials were characterized by global combustion rates, and kinetic parameters were determined for residual coke combustion. (orig.) [Deutsch] Das Verbrennungs- und Vergasungsverhalten von Rheinischer Braunkohle, Hausmuell, Restkunststoff, Holz und Klaerschlamm wurde in einer blasenbildenden, atmosphaerischen Laborwirbelschicht untersucht. Die Einsatzstoffe wurden in der mit Stickstoff fluidisierten Wirbelschicht pyrolysiert. Der verbleibende Restkoks wurde anschliessend unter Variation der Betriebsparameter mit Sauerstoff verbrannt oder mit Kohlendioxid vergast. Die unterschiedlichen Einsatzstoffe wurden durch globale Vebrennungsraten charakterisiert. Fuer die Restkoksverbrennung wurden kinetische Parameter ermittelt. (orig.)

  20. Case study of an MBT plant producing SRF for cement kiln co-combustion, coupled with a bioreactor landfill for process residues.

    Science.gov (United States)

    Grosso, Mario; Dellavedova, Stefano; Rigamonti, Lucia; Scotti, Sergio

    2016-01-01

    The paper describes the performances of the energy recovery pathway from the residual waste based on the production of a Solid Recovered Fuel (SRF) to be exploited via co-combustion in a cement kiln. The SRF is produced in a single stream Mechanical-Biological Treatment plant, where bio-drying of the waste is followed by mechanical refining in order to fulfil the quality requirements by the cement kilns. Peculiar of this MBT is the fact that sorting residues are disposed in a nearby landfill, managed according to a bioreactor approach, where landfill gas is collected for electric energy recovery. A detailed mass and energy balance of the system is presented based on one year operational data, followed by its Life Cycle Assessment. Results show that the system is energetically and environmentally effective, with most of the impacts being more than compensated by the savings of materials and energy. Major role in determining such outcome is the displacement of petcoke in the cement kiln, both in terms of its fossil CO2 emissions and of its life cycle impacts, including the trans-oceanic transport. To check the robustness of the results, two sensitivity analyses are performed on the landfill gas collection efficiency and on the avoided electric energy mix. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Lightweight combustion residues-based structural materials for use in mines. Quarterly report, 1 December 1994--28 February 1995

    Energy Technology Data Exchange (ETDEWEB)

    Chugh, Yoginder P.; Zhang, Yuzhuo; Ghosh, A.K.; Palmer, S.R; Peng, Suping, Xiao, Y. [Southern Illinois Univ., Carbondale, IL (United States)

    1995-12-31

    The overall goal of this project is to develop, design and test artificial supports (post and crib members) for use in mines manufactured from coal combustion by-product (CCB) based lightweight structural materials. The lightweight cement-fly ash grout with density ranging from 70 to 110 pcf has been developed incorporating very high volume (50--60 % of whole solid materials) fly ash. Characterization of individual component materials for the CCB-based structural materials has been performed for Class F fly ash, ASTM Type I cement, lime, silica fume, polypropylene fibers, protein-based foam, water-reducing agents, and calcium chloride. During the past quarter, we emphasized on screening mix designs and establishing mixing and curing procedures. We have demonstrated for the first time that cellular cement-fly ash grout can be developed with very low water: cement ratio (0.32--0.45). After forming, all the samples in the molds were moist cured in a chamber for 24-hours, at 90% relatively humidity (RH) and at 72{degrees}F. They were then demolded and transferred to a low pressure steam chamber (150{degrees}F and 100% RH). After steaming for 24 hours the samples were removed to a moist cure chamber prior to testing.

  2. El aceite de aguacate y sus propiedades nutricionales

    Directory of Open Access Journals (Sweden)

    R. Pérez Rosales

    2005-01-01

    Full Text Available El aceite de aguacate, por su composición de ácidos grasos, cumple con las recomendaciones nutricionales que se enfocan a reducir la cantidad de grasa saturada en la dieta. Se caracteriza por contener una baja proporción de ácidos grasos saturados (entre un 10 y 19 por ciento, depende de la variedad y el estado de madurez, una elevada cantidad de ácido oleico (puede llegar hasta un 80 por ciento, un nivel aceptable de ácidos grasos poliinsaturados (11-15 por ciento y nada de colesterol. Se ha demostrado que las dietas enriquecidas con aceite de aguacate son tan efectivas como aquellas que contienen aceite de maíz, aceite de soya o de girasol, para reducir colesterol total, colesterol LDL (lipoproteína de baja densidad y triglicéridos del plasma, tanto en individuos hipercolesterolémicos como con diabetes mellitus tipo 2, lo cual se refleja en una disminución de los riesgos cardiovasculares. El consumo de aceite de aguacate también eleva el porcentaje de colesterol HDL (lipoproteína de alta densidad del plasma, en modelos animales. Además, el aceite de aguacate posee un grado de aterogenicidad comparable al aceite de maíz o de oliva. La efectividad del aceite de aguacate en reducir colesterol total y colesterol LDL del plasma y su bajo nivel de aterogenicidad, indican que éste puede tener un papel benéfico dentro de una dieta nutritiva

  3. Extracción de aceite de café

    OpenAIRE

    López Fontal, Elkin Mauricio

    2010-01-01

    En el presente trabajo se realiza la extracción de aceite de café mediante el método de extrusión. En dicho proceso se obtienen dos productos: el aceite de café y la torta. Para tal propósito se utilizó café tostado, el cual se caracteriza por poseer una elevada cantidad de compuestos odoríferos; es importante saber que un criterio significativo en la valoración de la calidad del café, es su aroma. Al extraer el aceite, una parte significativa del contenido aromático del café tostado, que va...

  4. Effects of coal combustion residues on survival, antioxidant potential, and genotoxicity resulting from full-lifecycle exposure of grass shrimp (Palaemonetes pugio Holthius)

    International Nuclear Information System (INIS)

    Kuzmick, Danika M.; Mitchelmore, Carys L.; Hopkins, William A.; Rowe, Christopher L.

    2007-01-01

    Coal combustion residues (CCRs), largely derived from coal-fired electrical generation, are rich in numerous trace elements that have the potential to induce sublethal effects including oxidative stress, alterations in antioxidant status and DNA single strand breaks (SSB). CCRs are frequently discharged into natural and man-made aquatic systems. As the effects of CCRs have received relatively little attention in estuarine systems, the estuarine grass shrimp, Palaemonetes pugio, was chosen for this study. Grass shrimp were exposed in the laboratory to CCR-enriched sediments and food over a full life cycle. Survival to metamorphosis was significantly reduced in CCR-exposed larvae (17 ± 4 versus 70 ± 13% in the controls) but not in the juveniles or adults. The COMET assay, a general but sensitive assay for genotoxicity, was used to quantify DNA SSB in the adults. Total antioxidant potential was examined to assess the overall antioxidant scavenging capacity of CCR-exposed and non-exposed adult grass shrimp. Grass shrimp exposed to CCR significantly accumulated selenium and cadmium compared to unexposed shrimp, although an inverse relationship was seen for mercury accumulation. Chronic CCR exposure caused DNA SSB in hepatopancreas cells, as evidenced by the significantly increased percent tail DNA, tail moment, and tail length as compared to reference shrimp. However, no significant difference was observed in total antioxidant potential. Our findings suggest that genotoxicity may be an important mode of toxicity of CCR, and that DNA SSB may serve as a useful biomarker of exposure and effect of this very common, complex waste stream

  5. Effects of coal combustion residues on survival, antioxidant potential, and genotoxicity resulting from full-lifecycle exposure of grass shrimp (Palaemonetes pugio Holthius)

    Energy Technology Data Exchange (ETDEWEB)

    Kuzmick, Danika M.; Mitchelmore, Carys L.; Rowe, Christopher L. [University of Maryland Center for Environmental Science, Chesapeake Biological Laboratory, 1, Williams Street, PO Box 38, Solomons, MD, 20688 (United States); Hopkins, William A. [Department of Fisheries and Wildlife Sciences, Virginia Polytechnic Institute and State University, 100 Cheatham Hall, Blacksburg, VA (United States)

    2007-02-01

    Coal combustion residues (CCRs), largely derived from coal-fired electrical generation, are rich in numerous trace elements that have the potential to induce sublethal effects including oxidative stress, alterations in antioxidant status and DNA single strand breaks (SSB). CCRs are frequently discharged into natural and man-made aquatic systems. As the effects of CCRs have received relatively little attention in estuarine systems, the estuarine grass shrimp, Palaemonetes pugio, was chosen for this study. Grass shrimp were exposed in the laboratory to CCR-enriched sediments and food over a full life cycle. Survival to metamorphosis was significantly reduced in CCR-exposed larvae (17 {+-} 4 versus 70 {+-} 13% in the controls) but not in the juveniles or adults. The COMET assay, a general but sensitive assay for genotoxicity, was used to quantify DNA SSB in the adults. Total antioxidant potential was examined to assess the overall antioxidant scavenging capacity of CCR-exposed and non-exposed adult grass shrimp. Grass shrimp exposed to CCR significantly accumulated selenium and cadmium compared to unexposed shrimp, although an inverse relationship was seen for mercury accumulation. Chronic CCR exposure caused DNA SSB in hepatopancreas cells, as evidenced by the significantly increased percent tail DNA, tail moment, and tail length as compared to reference shrimp. However, no significant difference was observed in total antioxidant potential. Our findings suggest that genotoxicity may be an important mode of toxicity of CCR, and that DNA SSB may serve as a useful biomarker of exposure and effect of this very common, complex waste stream. (author)

  6. Los intangibles del aceite de oliva como ventaja competitiva

    OpenAIRE

    Ruiz Guerra, Ignacio; Martín López, Víctor Manuel; Molina Moreno, Valentín

    2012-01-01

    Objeto: Utilización de nuevas estrategias para el reposicionamiento del Aceite de Oliva a través de los activos intangibles.Diseño/metodología/enfoque: Aplicación del marco teórico de la intangibilidad al Aceite de Oliva y conceptualización de los activos intangibles y desarrollo de un estudio estadístico cuantitativo de valoración de los conceptos planteados.Aportaciones y resultados: Se propone una conceptualización de lo...

  7. Actividad antioxidante de compuestos aislados del residuo no-volátil del aceite esencial de naranja.

    Directory of Open Access Journals (Sweden)

    Vargas-Arispuro, L.

    1998-04-01

    Full Text Available There has been a growing interest in the food industry and in preventive medicine to search for «natural antioxidants». Therefore the objetive of this study was to evaluate the antioxidant activity of the non-volatile residue of essential orange oil in the oxidation of unrefined and freshly extracted olive oil. Essential orange oil was distilled to obtain a non-volatile residue and fracctionated on a Silica Gel 60 column. The antioxidant activity was determined by measuring peroxide value obtained after heating olive oil at 70 °C for 48 h. Six compounds were isolated and purified, four of these had antioxidant activity, α-tocopherol and three methoxylated flavones were identified using spectroscopic methods. This study confirmed that non-volatile fractions of essential orange oil contain natural antioxidants diferent from α-tocopherol.

    Existe un creciente interés en la industria alimentaria y en la medicina preventiva por la búsqueda de «antioxidantes naturales», por lo que nos planteamos evaluar la actividad antioxidante del residuo no volátil del aceite esencial de naranja contra la oxidación del aceite de oliva sin retinar y de reciente extracción. Mediante destilación del aceite esencial de naranja se obtuvo el residuo no-volátil, el cual se fraccionó en columna de silica gel 60. La actividad antioxidante fue medida por el valor de peróxidos producidos por el aceite de oliva al provocar la oxidación por calentamiento a 70 °C durante 48 h. Se aislaron seis compuestos mediante HPLC preparativo de los cuales cuatro tuvieron actividad antioxidante. Usando métodos espectroscópicos se identificaron α-tocoferol y tres flavonas metoxiladas. Con este estudio se confirmó que la fracción no volátil del aceite esencial de naranja contiene antioxidantes naturales diferentes al α-tocoferol.

  8. Aceite de frutos de Persea schiedeana en sobremaduración y cosechados de árboles en estado silvestre

    OpenAIRE

    Campos-Hernández, N; Cruz-Castillo, JG; Hernández-Montes, A; Rubio-Hernández, D

    2011-01-01

    En frutos sobremaduros de Persea schiedeana Nees colectados en árboles creciendo en estado silvestre se estudiaron las características químicas y sensoriales del aceite. La extracción de aceite con isopropanol y hexano tuvo un rendimiento de 12% aceite/pulpa (v/p). El aceite de P. schiedeana fue comparado con aceites comerciales de oliva y aguacate. El aceite de P. schiedeana tuvo menor número de insaturaciones y más ácidos grasos de cadena larga que los aceite de oliva y de aguacate. Los índ...

  9. Producción y Comercialización de Bases y Aceites Lubricantes Partiendo del Aceite Usado

    OpenAIRE

    Espol; Sosa Tobar, Edison Anibal; Castillo Tutiven, Christian Omar; Talbot, Jorge

    2015-01-01

    El aceite lubricante, resulta de un proceso de mezcla de bases lubricantes con aditivos; ambos son productos manufacturados a partir del petróleo en la refinerías. Dentro de sus aplicaciones más comunes están los automotores y la industria en general (transmisiones mecánicas, aplicaciones hidráulicas, etc.) Sin embargo, el empleo del mismo está sujeto a un periodo de vida útil que es el tiempo que tarda el aceite en perder sus propiedades producto de la contminación con partículas metálicas ...

  10. Aplicación de microondas en el tratamiento de emulsiones del tipo agua en aceite (w/o) y aceite en agua (o/w).

    OpenAIRE

    PÉREZ PÁEZ, ROCIO

    2011-01-01

    Las emulsiones del tipo agua en aceite (w/o) y aceite en agua (o/w) están compuestas por una mezcla de aceite, agua, lodo y otros agentes. Se pueden encontrar en el proceso y/o en los vertidos de diferentes tipos de industrias, tales como refinerías de petróleo, plantas procesadoras de aceite de consumo, industrias farmacéuticas, industrias de alimentos, etc. El calentamiento de un material a una frecuencia de microondas depende de la frecuencia de la onda electromagnética y de las propie...

  11. Extracción de aceite de café

    Directory of Open Access Journals (Sweden)

    Elkin Mauricio López Fontal

    2007-01-01

    Full Text Available En el presente trabajo se realiza la extracción de aceite de café mediante el método de extrusión. En dicho proceso se obtienen dos productos: el aceite de café y la torta. Para tal propósito se utilizó café tostado, el cual se caracteriza por poseer una elevada cantidad de compuestos odoríferos; es importante saber que un criterio significativo en la valoración de la calidad del café, es su aroma. Al extraer el aceite, una parte significativa del contenido aromático del café tostado, que varía según el método de extracción usado, sale con él. Es asI como se obtiene un aceite filo con una alta carga volátil, el cual presenta características organolépticas favorables. Al segundo producto que se obtiene, se le realizó análisis físico-químico en aras de mostrar sus bondades y propiedades particulares, y de acuerdo a los resultados obtenidos, es un producto que presenta un amplio potencial de utilización.

  12. Experimental findings on thermal use of residues and biofuels in circulating fluidized bed combustion systems; Experimentelle Ergebnisse zur thermischen Nutzung von Rest- und Biobrennstoffen in zirkulierenden Wirbelschichtfeuerungen

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, W.; Brunne, T.; Girndt, H. [Technische Univ. Dresden (Germany); Albrecht, J. [Lurgi Lentjes Babcock, Frankfurt am Main (Germany); Youssef, M. [Minia Univ. (Egypt)

    1996-12-31

    The energy Engineering Institute of Dresden Technical University investigated the combustion and emission characteristics of a number of combustion systems, including a circulating fluidized bed system with a capacity of 0.3 MW{sub th}. Egypt`s sugar cane industry produces large volumes of bagasse. The conbustion and emission characteristics of this biofuel in a circulating fludized bed combustion systems were investigated in a joint research project of the University of Minia and Dresden Technical University. (orig.) [Deutsch] Am Institut fuer Energietechnik der TU Dresden wird das Verbrennungs- und Emissionsverhalten verschiedenster Brennstoffe in unterschiedlichen Feuerungssystemen untersucht. Neben anderen Pilotanlagen steht eine zirkulierende Wirbelschichtfeuerung (ZWFS) mit einer Leistung von 0.3 MW{sub th} zur Verfuegung. In der Zuckerrohrindustrie Aegyptens fallen grosse Mengen von Bagasse an. In einer gemeinsamen Forschungsarbeit zwischen der Universitaet Minia und der TU Dresden sollte das Verbrennungs- und Emissionsverhalten dieses Biobrennstoffes in einer ZWSF untersucht werden. (orig)

  13. Experimental findings on thermal use of residues and biofuels in circulating fluidized bed combustion systems; Experimentelle Ergebnisse zur thermischen Nutzung von Rest- und Biobrennstoffen in zirkulierenden Wirbelschichtfeuerungen

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, W; Brunne, T; Girndt, H [Technische Univ. Dresden (Germany); Albrecht, J [Lurgi Lentjes Babcock, Frankfurt am Main (Germany); Youssef, M [Minia Univ. (Egypt)

    1997-12-31

    The energy Engineering Institute of Dresden Technical University investigated the combustion and emission characteristics of a number of combustion systems, including a circulating fluidized bed system with a capacity of 0.3 MW{sub th}. Egypt`s sugar cane industry produces large volumes of bagasse. The conbustion and emission characteristics of this biofuel in a circulating fludized bed combustion systems were investigated in a joint research project of the University of Minia and Dresden Technical University. (orig.) [Deutsch] Am Institut fuer Energietechnik der TU Dresden wird das Verbrennungs- und Emissionsverhalten verschiedenster Brennstoffe in unterschiedlichen Feuerungssystemen untersucht. Neben anderen Pilotanlagen steht eine zirkulierende Wirbelschichtfeuerung (ZWFS) mit einer Leistung von 0.3 MW{sub th} zur Verfuegung. In der Zuckerrohrindustrie Aegyptens fallen grosse Mengen von Bagasse an. In einer gemeinsamen Forschungsarbeit zwischen der Universitaet Minia und der TU Dresden sollte das Verbrennungs- und Emissionsverhalten dieses Biobrennstoffes in einer ZWSF untersucht werden. (orig)

  14. Aprovechamiento de las oleinas residuales procedentes del proceso de refinado de los aceites vegetales comestibles, para la fabricación de biodiesel

    OpenAIRE

    Pereda Marín, Juan; Barriga Mateos, F.; Álvarez-Mateos, María Paloma

    2003-01-01

    Se estudia un procedimiento para la obtención de Biodiesel a partir de las “Oleínas”. Biodiesel es un producto capaz de sustituir al combustible Diesel ordinario que se obtiene del petróleo y que consiste en una mezcla de ésteres metílicos de ácidos grasos. Las oleínas son unos residuos que resultan del proceso de refina- do de aceites vegetales para su uso alimentario y se componen de una mezcla de triglicéridos y ácidos grasos libres, con un con- tenido de estos últimos...

  15. Determinación de las propiedades físicas y carga crítica del aceite vegetal Jatropha curcas L

    OpenAIRE

    Rodríguez-Martínez, Calixto; Lafargue-Pérez, Francisco; Sotolongo-Pérez, José Ángel; Rodríguez-Poveda, Annarella; Chitue de Assuncao Nascimento, Juliano

    2012-01-01

    En el trabajo se determinaron las propiedades físicas y la carga critica del aceite de Jatropha curcas L, obtenido de las plantas cultivadas en la provincia de Guantánamo en Cuba. Estas propiedades fueron comparadas con las propiedades de otros aceites vegetales (aceite ricino, aceite de girasol, aceite de colza y aceite de soya) usados como biolubricantes. Los resultados mostraron que las propiedades físicas del aceite de Jatropha curcas L fueron similares a la mayoría de los aceites vegetal...

  16. Developments in the technology for the combustion of water emulsions in Mexican fuel oil; Desarrollos en la tecnologia para la combustion de emulsiones agua en combustoleo mexicano

    Energy Technology Data Exchange (ETDEWEB)

    Diego, Antonio Marin; Martinez Flores, Marco A.; Tamayo Flores, Gustavo; Alarcon Quiroz, Ernesto; Melendez Cervantes, Carlos [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)

    2001-07-01

    The residual petroleum oil (fuel oil) is the most used fuel in boilers of electrical and industrial power stations. Nevertheless, the use of this fuel can generate diverse problems such as the elevated particle emissions, that affect the boiler efficiency, darken the visibility by the smoke that leaves the chimneys and is emitted to the Environment. In addition, sulfur trioxide is produced, which reacts with the water present in the combustion gases, forming sulfuric acid that, when emitted, also affects the visibility of the plume and can be condensed, originating corrosion and increased accumulation of deposits in the boilers. The experimental research was made in a comparative base, between combustion tests of fuel oil, with emulsions where the water concentration and the size of the drops of this one was varied. A diagram of the supply of fuel and preparation of emulsions in a pilot furnace is shown. The article contains graphs of the effect of the water concentration of the emulsions in the particulate emission. The article contains figures of the cenospheres produced by the fuel oil combustion (500 x) and the ones produced by the combustion with 5% of water (500 x). Also shows graphs of the effect of the water drop size of emulsions in the particulate emission, of the reduction of the sulfur trioxide with soluble magnesium products in the water of emulsions, and of the free particle acidity with neutralizers of water emulsions of soluble magnesium. [Spanish] El aceite residual de petroleo (combustoleo) es el combustible mas utilizado en calderas de centrales electricas e industriales. Sin embargo, el uso de este combustible puede generar diverso problemas como las emisiones elevadas de particulas, que afectan la eficiencia de una caldera, obscurecen la visibilidad pero el humo que sale de las chimeneas y se emiten al medio ambiente. Ademas se produce trioxido de azufre, el cual reacciona con el vapor de agua presente en los gases de combustion, formado acido

  17. Solid residues

    International Nuclear Information System (INIS)

    Mulder, E.; Duin, P.J. van; Grootenboer, G.J.

    1995-01-01

    A summary is presented of the many investigations that have been done on solid residues of atmospheric fluid bed combustion (AFBC). These residues are bed ash, cyclone ash and bag filter ash. Physical and chemical properties are discussed and then the various uses of residues (in fillers, bricks, gravel, and for recovery of aluminium) are summarised. Toxicological properties of fly ash and stack ash are discussed as are risks of pneumoconiosis for workers handling fly ash, and contamination of water by ashes. On the basis of present information it is concluded that risks to public health from exposure to emissions of coal fly ash from AFBC appear small or negligible as are health risk to workers in the coal fly ash processing industry. 35 refs., 5 figs., 12 tabs

  18. A new power station with clean combustion of coal residues financed by the Commission wins an international prize. Una nueva central electrica de combustion limpia de residuos de carbon financiada por la Comision gana un premio internacional

    Energy Technology Data Exchange (ETDEWEB)

    Furfari, S. (Commission of the European Communities, Brussels (Belgium). Directorate General for Energy, Energy Technology Unit)

    1993-07-01

    Between 1987 and 1989 10,55 million ecus were given by the European Commission's Demonstration Programme for the construction of the Emile Huchet power station using circulating fluidized bed combustion technology. The power station was constructed jointly by Charbonnages de France, COREAL, Stein Industrie and Lurgi. An important feature was its ability to burn coal preparation wastes cleanly. Despite burning poor quality fuel its emissions are well below the maximum standards. Other stations of this type are now planned in France.

  19. ACE-it: a tool for genome-wide integration of gene dosage and RNA expression data

    NARCIS (Netherlands)

    van Wieringen, W.N.; Belien, J.A.M.; Vosse, S.; Achame, E.M.; Ylstra, B.

    2006-01-01

    Summary: We describe a tool, called ACE-it (Array CGH Expression integration tool). ACE-it links the chromosomal position of the gene dosage measured by array CGH to the genes measured by the expression array. ACE-it uses this link to statistically test whether gene dosage affects RNA expression. ©

  20. EVALUACIÓN NUTRICIONAL DE LOS ÁCIDOS GRASOS DE ACEITE DE SEMILLAS DE PALQUI

    Directory of Open Access Journals (Sweden)

    Ramiro Escalera Vásquez

    2015-07-01

    Tomando en cuenta los resultados de esta evaluación, se puede concluir que el consumo de semillas de palqui y su aceite, son beneficiosos y no riesgosos para la salud. Por consiguiente, la semilla de palqui puede ser industrializada como aceite comestible.

  1. Actividad repelente de aceites esenciales contra las picaduras de Lutzomyia migonei (Diptera: Psychodidae

    Directory of Open Access Journals (Sweden)

    Elsa Nieves

    2010-12-01

    Full Text Available Los repelentes naturales de extractos de plantas han mostrado eficacia contra diferentes especies de insectos. El presente estudio evaluó la acción repelente de aceites esenciales extraídos de ocho especies de plantas contra las picaduras de Lutzomyia migonei, vector de Leishmania. Los aceites esenciales se obtuvieron por hidrodestilación, utilizando una trampa de Clevenger, a partir de Hyptis suaveolens, Pimenta racemosa, Piper marginatum, Monticalia imbricatifolia, Pseudognaphalium caeruleocanum, Espeletia shultzii, Plectranthus amboinicus y Cinnamomun zeylanicum. Los ensayos de repelencia se realizaron sobre humanos en condiciones de laboratorio, frente a hembras de L. migonei provenientes de colonia, utilizando el método de la mano en la jaula. Los aceites con efecto repelente también se ensayaron con distintos voluntarios y concentraciones. Se determinó el porcentaje de protección y el tiempo de protección. Los resultados revelaron que el aceite de P. caeruleocanum y C. zeylanicum fueron los más efectivos. El aceite de P. amboinicus presentó efecto de repelencia satisfactorio, sin embargo, ocasionó picazón y toxicidad en la piel. Los aceites de P. marginatum, H. suaveolens y P. racemosa no evidenciaron efecto repelente; el resto de los aceites presentaron repelencia significativa en grado variable. Los aceites de P. caeruleocanum y C. zeylanicum mostraron un 95% de protección de 3h contra las picaduras de L. migonei. El aceite de P. caeruleocanum presentó el mayor tiempo de protección, de más de 4h y de 2h en concentraciones de 50% y 10%, respectivamente. Los resultados sugieren que el aceite P. caeruleocanum podría ser un potencial candidato como repelente natural contra la picadura de dípteros posibles transmisores de Leishmania.

  2. Kinetic models for pyrolysis and combustion of sewage sludge[Held jointly with the 4. Canadian organic residuals and biosolids managment conference

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, R.; Udaquiola, S. [Univ. Nacional de San Juan, San Juan (Argentina). Lab. Tec. Amb., Inst. de Ing. Qca; Gauthier, D; Flamant, G. [PROMES-CNRS, Font-Romeu Odeillo (France); Mazza, G. [Univ. Nacional Del Comahue, Neuquen (Argentina). Dept. de Quimica; Martinez, O. [Univ. Nacional de la Plata, La Plata (Argentina). CINDECA-CONICET

    2007-07-01

    In thermochemical conversion processes that produce energy, the kinetics of waste decomposition must be considered. The rate of mass loss due to thermal decomposition determines the available fuel on the fire triangle of heat, fuel and oxygen. Heating rates in thermobalance experiments are low, and are often used to study the primary reactions in the decomposition of solids since their cracking is negligible. Thermogravimetry is an option for determining the decomposition profile of a solid in terms of its temperature versus the kinetics of its decomposition. This paper presented the thermal analysis and results of a study that used thermogravimetric analyses on dry samples of sewage sludge from San Juan, Argentina in an inert and oxidative atmosphere. Three peaks were observed in all differential thermogravimetric curves during the organic matter decomposition. In order to explain the experimental data, various reaction schemes were set up. The first two schemes considered 3 fractions decomposing in parallel during pyrolysis, with oxidative pyrolysis of all fractions during combustion or only two. The third scheme considered the decomposition of 2 fractions only but with dissymmetrical behavior during the whole pyrolysis and combustion phenomenon. It was concluded that the simulations were a good agreement with the experimental data for the first 2 schemes only, and overall, the fit was better with the second scheme. 11 refs., 4 figs.

  3. Estudio comparativo de las características físico-químicas del aceite de sacha inchi (Plukenetia volubilis l., aceite de oliva (Olea europaea y aceite crudo de pescado

    Directory of Open Access Journals (Sweden)

    Luz María Paucar-Menacho

    2015-01-01

    Full Text Available Los aceites vegetales tales como el aceite de sacha inchi (ASI y oliva (AO contienen ácidos grasos mono-insaturados (omega-9 y poliinsaturados (omega-6, y pequeñas cantidades de omega-3. Por el contrario, los aceites de origen marino como el aceite crudo de pescado (ACP se caracterizan por su alto contenido en omega-3. El objetivo de la presente investigación fue determinar y comparar las características físico-químicas de estos tres aceites a fin de establecer cuál es el mejor para el uso alimentario. El Índice de acidez, índice de refracción y densidad relativa se determinó por métodos oficiales AOAC, y el tiempo de vida útil por el método Rancimat, a tres temperaturas (100 °C; 120 °C y 150 °C, extrapolando los resultados a 25 °C.Los resultados obtenidos en la caracterización fisicoquímica indican que estos aceites son significativamente diferentes. Los índices de acidez en % de ácido oleico fueron de 1,08, 1,14 y 1,561 para ASI, AO y ACP respectivamente. Los índices de refracción (20 °C fueron 1,475, 1,469 y 1,481 para ASI, AO y ACP respectivamente, la densidad relativa fue 0,9283, 0,9152 y 0,9308 para ASI, AO y ACP respectivamente. La vida útil para ASI, AO y ACP fue de 93, 137 y 2 días respectivamente. La composición de ácidos grasos tanto en los aceites de origen vegetal y marino además de su vida útil, imparte gran importancia desde el punto de vista nutricional, ya que están contenidos significativamente en los aceites estudiados. Los resultados indican la importancia de este tipo de aceites en la alimentación humana.

  4. Aceites vegetales de uso frecuente en Sudamérica: características y propiedades

    OpenAIRE

    Durán Agüero, Samuel; Torres García, Jairo; Sanhueza Catalán, Julio

    2015-01-01

    El consumo de aceites vegetales se ha incrementado en las últimas décadas en nuestra sociedad y son parte importante de la dieta en todo el mundo. Sudamérica es un gran productor de diferentes aceites vegetales. La composición de los aceites vegetales no es estándar, ya que varía considerablemente en el aporte de ácidos grasos saturados, monoinsaturados y poliinsaturados, y particularmente en el aporte de ácidos grasos omega-6 y omega-3, asociado a la fuente de origen, ya sea especie vegetal,...

  5. An Evaluation of the Automated Cost Estimating Integrated Tools (ACEIT) System

    Science.gov (United States)

    1989-09-01

    C~4p DTIC S ELECTE fl JAN12 19 .1R ~OF S%. B -U AN EVALUATION OF THE AUTOMATED COST ESTIMATING INTEGRATED TOOLS ( ACEIT ) SYSTEM THESIS Caroline L...Ohio go 91 022 AFIT/GCA/LSQ/89S-5 AN EVALUATION OF THE AUTOMATED COST ESTIMATING INTEGRATED TOOLS ( ACEIT ) SYSTEM THESIS Caroline L. Hanson Major, USAF...Department of Defense. AFIT/GCA/LSQ/89S-5 AN EVALUATION OF THE AUTOMATED COST ESTIMATING INTEGRATED TOOLS ( ACEIT ) SYSTEM THESIS Presented to the

  6. CARACTERIZACIÓN Y ACTIVIDAD ANTIOXIDANTE DEL ACEITE DE LA SEMILLA DE PALTA Persea americana MILL.

    OpenAIRE

    Rengifo, Pedro G.; Carhuapoma, Mario; Artica, Luis; Castro, Américo J.; López, Sofía

    2017-01-01

    La semilla de palta es una parte del fruto descartada en la obtención industrial del aceite de pulpa y podría ser una fuente de ácidos grasos esenciales y otros fitoconstituyentes. El presente trabajo de investigación tuvo como objetivo caracterizar al aceite de la semilla de Persea americana Mill. Var. Hass Fuerte y su actividad antioxidante. Al aceite obtenido por el método de Soxhlet, se le hizo la caracterización fisicoquímica siguiendo las normas AOCS (Sociedad Americana de la Química de...

  7. Estudio de la obtención de biodiesel a partir de aceite comestible usado

    OpenAIRE

    García-Díaz, Marilin; Gandón-Hernández, José; Maqueira-Tamayo, Yudisel

    2013-01-01

    Nuestro país actualmente no cuenta con una estrategia para utilizar racionalmente el volumen de aceite vegetal usado que se genera en la industria alimentaria y el sector turístico proveniente del proceso de fritura, es por eso que el presente trabajo tiene como objetivo estudiar la obtención del biodiesel a partir de aceites comestibles usados y metanol. Las cantidades de aceite y reactivos para que se desarrolle la reacción de transesterificación, mediante la cual se obtiene biodiésel y gli...

  8. Combustion engineering

    CERN Document Server

    Ragland, Kenneth W

    2011-01-01

    Introduction to Combustion Engineering The Nature of Combustion Combustion Emissions Global Climate Change Sustainability World Energy Production Structure of the Book   Section I: Basic Concepts Fuels Gaseous Fuels Liquid Fuels Solid Fuels Problems Thermodynamics of Combustion Review of First Law Concepts Properties of Mixtures Combustion StoichiometryChemical EnergyChemical EquilibriumAdiabatic Flame TemperatureChemical Kinetics of CombustionElementary ReactionsChain ReactionsGlobal ReactionsNitric Oxide KineticsReactions at a Solid SurfaceProblemsReferences  Section II: Combustion of Gaseous and Vaporized FuelsFlamesLaminar Premixed FlamesLaminar Flame TheoryTurbulent Premixed FlamesExplosion LimitsDiffusion FlamesGas-Fired Furnaces and BoilersEnergy Balance and EfficiencyFuel SubstitutionResidential Gas BurnersIndustrial Gas BurnersUtility Gas BurnersLow Swirl Gas BurnersPremixed-Charge Engine CombustionIntroduction to the Spark Ignition EngineEngine EfficiencyOne-Zone Model of Combustion in a Piston-...

  9. Contenido de plomo y cadmio en aceites de girasol

    Directory of Open Access Journals (Sweden)

    López Martínez, M. C.

    2001-08-01

    Full Text Available We have studied the lead and cadmium content in 21 samples of sunflower oil from Andalucía (Southern Spain. These elements are toxicological importance and the sunflower oil is widely consumed in Spain. Samples were mineralized with nitric acid and vanadium pentoxide as catalyst, and ana lyzed using electrothermal atomization atomic absorption spectroscopy. The temperature-time programme for the graphite furnace was optimized for each element, and the accuracy, precision, sensitivity and detection limit of the method were evaluated. Concentrations of lead ranged from not detectable to 167.58 μg/kg and cadmium concentrations ranged from 0.87 to 8.30 μg/kg. The data obtained are not excessive and similar to those mentioned by other authors; however, one sample of the total analyzed surpassed the limit of 0.1 ppm of lead proposed by the Spanish and European Legislation. A statistical significative correlation has been established between Pb and Cd levels (p Se ha determinado el contenido de plomo y cadmio en 21 muestras de aceite de girasol, todas ellas producidas en Andalucía (Sur de España. Ambos elementos tienen una gran importancia toxicológica y el aceite de girasol es muy consumido en España. Las muestras han sido mineralizadas con ácido nítrico, utilizando pentóxido de vanadio como catalizador, y analizadas mediante espectroscopia de absorción atómica con atomización electrotérmica. Se ha optimizado el programa temperatura-tiempo del horno de grafito para cada elemento y se ha evaluado la exactitud, precisión, sensibilidad y límite de detección del método. Las concentraciones de plomo han oscilado entre no detectables y 167.58 μg/kg y las concentraciones de cadmio entre 0.87 y 8.30 μg/kg. Estos datos no resultan excesivos y concuerdan con los aportados por otros autores; no obstante, una de las muestras analizadas supera el límite máximo de 0.1 ppm de Pb establecido en las Legislaciones Española y Europea. Se

  10. TRANSESTERIFICACIÓN DE ACEITE DE HIGUERILLA CRUDO UTILIZANDO CATALIZADORES HETEROGÉNEOS - ESTUDIO PRELIMINAR

    Directory of Open Access Journals (Sweden)

    GINA HINCAPIÉ

    2011-01-01

    Full Text Available Se estudió la producción de biodiesel mediante transesterificación de aceite de higuerilla crudo con etanol y metanol usando catalizadores heterogéneos. Los catalizadores utilizados fueron el óxido de calcio, carbonato de sodio y de potasio y un silicato de zinc con estructura tipo hemimorfita. La formación de alquil-ésteres fue cuantificada mediante cromatografía de gases. Las mayores conversiones fueron obtenidas con carbonato de potasio en etanol y con la hemimorfita en metanol a una concentración de 3% con respecto al peso de aceite, usando una relación molar de alcohol a aceite de 60 y luego de la pre-esterificación del aceite crudo. Bajo estas condiciones la conversión con carbonato de potasio fue 74.9% y con la hemimorfita fue 66.2%.

  11. Propiedades mecánicas de aceites y grasas vegetales

    Directory of Open Access Journals (Sweden)

    de Dios Alvarado, Juan

    1995-10-01

    Full Text Available Data of mechanical properties are presented for crude oils from avocado pulp, lupin grain, peanuts, soybean, sesame, cotton, castor-oil, linseed and passion fruit seeds; refined oils from sunflower, corn, peanut, olive and soybean; and cocoa, coconut, palm-oil and kernel palm-oil fats.
    Correlation equations which describe the effect of temperature on the refractive index, density, viscosity and surface tension are obtained, and values of coefficient of expansion and activation energy for flow are calculated.

    Se presentan los valores de las principales propiedades mecánicas determinadas en aceites crudos extraídos de pulpa de aguacate, granos o semillas de sésamo, algodón, altramuz o chocho, ricino, linaza, maní o cacahuete, maracuyá y soja; aceites refinados provenientes de semillas de girasol, germen de maíz, maní, oliva y soja; grasas extraídas de cacao, copra de coco, pulpa de palma africana y almendras de palma africana.
    Con los datos experimentales se establecen ecuaciones de correlación que describen el efecto de la temperatura sobre el índice de refracción, la densidad, la viscosidad y la tensión superficial. En cada producto, con los datos de la densidad se calcula el coeficiente volumétrico de expansión térmica y con los de la viscosidad la energía de activación.

  12. Extracción de aceite de aguacate: Un experimento industrial

    Directory of Open Access Journals (Sweden)

    Martínez Nieto, L.

    1992-02-01

    Full Text Available The results of an industrial experiment to obtain avocado oil by continuous process similar to that for obtaining olive oil are analyzed. Possible ways of improving the method and thus the yield are pointed out.

    Se analizan los resultados obtenidos en un experimento industrial de obtención de aceite de aguacate por un proceso continuo similar al de obtención de aceite de oliva, indicando las posibles modificaciones para mejorar el rendimiento.

  13. Exercise manual for the Augmented Computer Exercise for Inspection Training (ACE-IT) software

    Energy Technology Data Exchange (ETDEWEB)

    Dobranich, P.R.; Widney, T.W.; Goolsby, P.T. [Sandia National Labs., Albuquerque, NM (United States). Cooperative Monitoring Center and Regional Security; Nelson, J.D.; Evanko, D.A. [Ogden Environmental and Energy Services, Inc., Albuquerque, NM (United States)

    1997-09-01

    The on-site inspection provisions in many current and proposed arms control agreements require extensive preparation and training on the part of both the Inspected Party and the Inspection Team. Current training techniques include table-top inspections and practice inspections. The Augmented Computer Exercise for Inspection Training (ACE-IT), an interactive computer training tool, increases the utility of table-top inspections. ACE-IT has been designed to provide training for a hypothetical challenge inspection under the Chemical Weapons Convention (CWC); however, this training tool can be modified for other inspection regimes. Although ACE-IT provides training from notification of an inspection through post-inspection activities, the primary emphasis of ACE-IT is in the inspection itself--particularly with the concept of managed access. ACE-IT also demonstrates how inspection provisions impact compliance determination and the protection of sensitive information. The Exercise Manual supplements the ACE-IT software by providing general information on on-site inspections and detailed information for the CWC challenge inspection exercise. The detailed information includes the pre-inspection briefing, maps, list of sensitive items, medical records, and shipping records.

  14. Combining mechanical-biological residual waste treatment plants with the carbonisation-combustion process; Kombination MBA mit dem Schwel-Brenn-Verfahren

    Energy Technology Data Exchange (ETDEWEB)

    Diekmann, J.; Wiehn, G. [Siemens AG Unternehmensbereich KWU, Erlangen (Germany). Bereich Energieerzeugung

    1998-09-01

    The disposal market for household waste is strongly influenced by the legal framework governing it. A further factor that makes it difficult for the authorities responsible for disposal to decide on residual waste disposal by means of thermal or mechanical-biological treatment plants is the downward pressure on disposal prices from inexpensive, underused landfills. This makes it all the more important for a future-oriented waste management to develop a both economically and ecologically optimised waste disposal concept. In this situation there is much in favour of adopting a concept consisting of a combination of mechanical, mechanical-biological, and thermal treatment which takes due account of waste disposal concepts at the regional and supraregional scale. [Deutsch] Der Entsorgungsmarkt fuer Siedlungsabfaelle wird stark durch die Entwicklung der rechtlichen Rahmenbedingungen beeinflusst. Hinzu kommt, dass der Entscheidungsprozess der oeffentlichen Entsorgungstraeger zur Restabfallentsorgung mittels thermischer oder mechanisch-biologischer Anlagen durch den Druck auf die Entsorgungspreise aufgrund der kostenguenstigen, nicht ausgelasteten Deponien erschwert wird. Umso mehr muss das Ziel einer zukunftsorientierten Abfallwirtschaft sein, unter oekonomischen und oekologischen Gesichtspunkten ein optimiertes Abfallkonzept aufzubauen. Hier kann es sehr hilfreich sein, sich eines Konzeptes, bestehend aus der Kombination von mechanischer, mechanisch-biologischer und thermischer Behandlung unter Beruecksichtigung des regionalen und ueberregionalen Abfallkonzeptes zu bedienen. (orig./SR)

  15. Epoxidación del aceite vegetal de Jatropha curcas L con ácido perfórmico

    OpenAIRE

    Lafargue Pérez, F.; Salazar Avila, O.; Díaz Velázquez, M.; Leiva Aguilar, I.; Sánchez Hechavarría, J.

    2015-01-01

    Para producir aceite base para lubricantes a partir del aceite vegetal de Jatropha curcas L con una buena estabilidad oxidativa, el aceite de Jatropha curcas L refinado fue modificado químicamente. La epoxidación fue realizada con perácido formado in situ, por reacción del ácido fórmico con peróxido de hidrógeno. Las propiedades físico- químicas del aceite de Jatropha curcas L epoxidado, tales como: índice de yodo, densidad, viscosidad dinámica y estabilidad oxidativa (prueba Rancimat) fueron...

  16. Creación de una empresa de recogida selectiva y gestión de aceite vegetal usado

    OpenAIRE

    Iribarren García, Iñigo

    2010-01-01

    Este proyecto trata sobre la creación de una empresa donde todo va a girar en torno a un producto principal: el aceite vegetal usado. A partir de ahí, en la empresa aparecen cuatro líneas de negocio independientes y a la vez relacionadas, que directa o indirectamente están ligadas con el aceite usado. Las cuatro líneas de trabajo van a ser una parte referente al servicio de recogida del aceite, actuación de la cual derivan otras dos de las cuatro líneas de negocio, como son la venta del aceit...

  17. Coal combustion ashes: A radioactive Waste?

    International Nuclear Information System (INIS)

    Michetti, F.P.; Tocci, M.

    1992-01-01

    The radioactive substances naturally hold in fossil fuels, such as Uranium and Thorium, after the combustion, are subjected to an increase of concentration in the residual combustion products as flying ashes or as firebox ashes. A significant percentage of the waste should be classified as radioactive waste, while the political strategies seems to be setted to declassify it as non-radioactive waste. (Author)

  18. Evaluación oxidativa de las mezclas de aceites de leguminosas del Desierto de Sonora con aceites de maíz y soja durante su almacenamiento

    Directory of Open Access Journals (Sweden)

    Vázquez-Moreno, L.

    2001-12-01

    Full Text Available During storage, oils from seeds of wild legumes of the Sonoran Desert have shown greater stability than oils derived from conventional sources. In this work, oxidation process was evaluated during the storage (122 day of mixtures of oils: Mezquite Prosopis juliflora, Gatuña Mimosa grahamii, Palo fierro Olneya tesota, Vino rama Acacia constricta, Palo de brea Cercidium praecox and Palo verde Parkinsonia aculeata with oils from soy and maize. Ratios were 1:1, 2:1 and 3:1. Evaluated parameters included: Peroxides (P.V., Iodine (I.V., Acid (A.V., p-Anisidine (p-A values. Results showed that mixtures containing wild and maize oil showed 2-4 meq/Kg as initial values of iodine, while after 122 days of storage the value was 4-7 meq/Kg. Mixtures containing soy oil presented 3-6 meq-Kg initially, and 8-15 meq-Kg were detected at the end experiment. No differences were observed in I.V. and A.V. values in maize mixtures. On the contrary, mixtures containing soy oil presented increments in I.V. Also, A.V. presented a slight increment in 1:1 mixtures. p-Anisidine values presented and small increment in maize mixtures (3:1 ratio while this increment was larger in mixtures containing soy oils and Gatuña or Palo fierro oil. These latter oils when were mixed with maize oils presented the lowest increments in all evaluated indexes.The oils of palo fierro and blended gatuña with oil of corn didn’t present changes in their concentration in the palmitic and araquidic acid during the storage. The concentration of the oleic acid in the mezquite oils (3:1, gatuña (1:1, 2:1 and 3:1, vinorama (3:1, as well as the linoleic and erucic acids in gatuña in their three mixtures didn’t present changes neither alteration during the storage, for what you are considered the oils of palo fierro, gatuña and vinorama the most stable in the present study.Los aceites de semillas de leguminosas silvestres han mostrado mayor estabilidad que algunos aceites convencionales

  19. Combustion physics

    Science.gov (United States)

    Jones, A. R.

    1985-11-01

    Over 90% of our energy comes from combustion. By the year 2000 the figure will still be 80%, even allowing for nuclear and alternative energy sources. There are many familiar examples of combustion use, both domestic and industrial. These range from the Bunsen burner to large flares, from small combustion chambers, such as those in car engines, to industrial furnaces for steel manufacture or the generation of megawatts of electricity. There are also fires and explosions. The bountiful energy release from combustion, however, brings its problems, prominent among which are diminishing fuel resources and pollution. Combustion science is directed towards finding ways of improving efficiency and reducing pollution. One may ask, since combustion is a chemical reaction, why physics is involved: the answer is in three parts. First, chemicals cannot react unless they come together. In most flames the fuel and air are initially separate. The chemical reaction in the gas phase is very fast compared with the rate of mixing. Thus, once the fuel and air are mixed the reaction can be considered to occur instantaneously and fluid mechanics limits the rate of burning. Secondly, thermodynamics and heat transfer determine the thermal properties of the combustion products. Heat transfer also plays a role by preheating the reactants and is essential to extracting useful work. Fluid mechanics is relevant if work is to be performed directly, as in a turbine. Finally, physical methods, including electric probes, acoustics, optics, spectroscopy and pyrometry, are used to examine flames. The article is concerned mainly with how physics is used to improve the efficiency of combustion.

  20. Experimental study on combustion and slagging characteristics of tannery sludge

    International Nuclear Information System (INIS)

    Li, Chunyu; Jiang, Xuguang; Fei, Zhenwei; Chi, Yong; Yan, Jianhua

    2010-01-01

    Incineration is the most reasonable technique for tannery sludge disposal. The combustion and gaseous products emission characteristics of tannery sludge were investigated in this study. Tendency of slagging for combustion residue was also investigated based on the composition and microscopic scanning analysis. The high content of volatile matters and ash in tannery sludge was discovered. It was shown that the thermal decomposition and combustion of tannery sludge mainly occurs in a temperature frame between 150 degree Celsius and 780 degree Celsius. Organic acid was determined as the most important gaseous pollutant at low temperature combustion. The combustion residue from a specially designed furnace was analyzed by X-ray diffractometer (XRD) and energy dispersion spectroscopy (EDS) microprobe coupled in a scanning electron micro-scope (SEM). There is large amount of Ca in the combustion residue, and CaO was the main inorganic composition in these residues. The tannery sludge studied in this paper has a strong tendency of slagging, and the fusion of the residue began at 900 degree Celsius in combustion. It was further discovered that almost all the zinc (Zn) in tannery sludge is volatilized at 900 degree Celsius. The degree of volatilization for heavy metals at 900 degree Celsius followed the order of Zn > Cd >Cu > Mn > Pb > Cr. Most of Cr in tannery sludge is enriched in the residue during combustion. The present study reveals that it is critical to control the combustion temperature for optimal combustion efficiency and minimization of pollutants emission. (author)

  1. Influencia de las concentraciones de aceite y emulsionante en las propiedades reológicas de emulsiones aceite en agua del tipo salsa fina

    Directory of Open Access Journals (Sweden)

    Franco, José María

    1995-04-01

    Full Text Available The viscous and viscoelastic behaviour of food emulsions containing a mixture of egg yolk and sucrose stearate as a function of oil and sucrose stearate concentrations were studied. Oil concentrations ranged between 40- 55% w/w for emulsions containing 5% w/w sucrose stearate and sucrose ester concentrations varied between 0-10% w/w for emulsions containing 50% w/w oil. steady flow, linear oscillatory shear tests and droplet size distribution measurements were carried out. An increase in oil or emulsifier concentration produced an increase in both the steady-state viscosity and in the viscoelastic functions. The results have been explained on the basis of the relationship between the structural parameters and the rheology of the emulsions studied.

    Se ha estudiado la influencia que ejercen las concentraciones de aceite y emulsionante sobre el comportamiento viscoso y viscoelástico de emulsiones alimentarias con bajo contenido en aceite estabilizadas por una mezcla de yema de huevo y estearato de sacarosa. Se han preparado emulsiones variando la concentración de aceite entre el 40 y el 55% p/p en emulsiones con un 5% p/p en sucroéster y la concentración de sucroéster entre el 0 y el 10% p/p manteniendo un 50% p/p en aceite. Se han realizado medidas reológicas en cizalla oscilatoria dentro del intervalo de viscoelasticidad lineal, representativas de un estado imperturbado, y medidas en cizalla estacionaria, que causan una gran destrucción estructural. También se han determinado las distribuciones de tamaños de gota. Un aumento en el contenido de aceite o emulsionante produce un aumento de las funciones viscoelásticas dinámicas y de la viscosidad estacionaria. Estos resultados se explican en función de los parámetros estructurales de las emulsiones.

  2. Efecto del suplemento de aceites vegetales sobre el perfil lipídico en ratas wistar.

    Directory of Open Access Journals (Sweden)

    Elpidia Poveda

    2005-03-01

    Full Text Available Introducción. Se informan efectos sobre el perfil lipídico por acción de los tocoferoles, tocotrienoles y ácidos grasos saturados, monoinsaturados y poliinsaturados. Objetivo. Evaluar el efecto del consumo de aceites vegetales de alta utilización en Colombia (palma, soya, maíz, girasol y canola sobre las concentraciones sanguíneas de triglicéridos, colesterol total y colesterol-HDL en ratas Wistar. Metodología. Se cuantificaron tocoferoles, tocotrienoles y ácidos grasos de los aceites por cromatografía líquida de alta resolución. A los animales se les suministró un suplemento de 0,2 ml/día de aceite durante 4 semanas; se sacrificó un gru o de cada tratamiento (grupos tratados con aceite de palma, aceite de soya, aceite de maíz, aceite de girasol y aceite de canola para obtener muestras de sangre y cuantificar triglicéridos, colesterol total y colesterol- HDL. Los datos se analizaron según media, desviación estándar, análisis de varianza y Bonferroni. Resultados. No se presentaron diferencias en los triglicéridos a excepción del grupo control versus soya en la tercera semana de tratamiento; se observó también una tendencia a la disminución en el grupo de palma y al aumento en los de girasol y canola. No se encontraron diferencias significativas en colesterol total en ninguna de las semanas de intervención. Se presentaron diferencias en las concentraciones de colesterol HDL en las semanas de tratamiento (p=0,005, una tendencia a la disminución en el grupo de palma y al aumento en el grupo de girasol y maíz. Conclusión. Los aceites modifican el perfil lipídico; el bajo contenido de ácidos grasos saturados, el contenido de tocoferoles y tocotrienoles son favorables para el aumento del colesterol HDL; los tocotrienoles probablemente disminuyen los troglicéridos y atenúan las respuestas desfavorables de los ácidos grasos saturados.

  3. Field determination of biomass burning emission ratios and factors via open-path FTIR spectroscopy and fire radiative power assessment: headfire, backfire and residual smouldering combustion in African savannahs

    Directory of Open Access Journals (Sweden)

    M. J. Wooster

    2011-11-01

    Full Text Available Biomass burning emissions factors are vital to quantifying trace gas release from vegetation fires. Here we evaluate emissions factors for a series of savannah fires in Kruger National Park (KNP, South Africa using ground-based open path Fourier transform infrared (FTIR spectroscopy and an IR source separated by 150–250 m distance. Molecular abundances along the extended open path are retrieved using a spectral forward model coupled to a non-linear least squares fitting approach. We demonstrate derivation of trace gas column amounts for horizontal paths transecting the width of the advected plume, and find for example that CO mixing ratio changes of ~0.01 μmol mol−1 [10 ppbv] can be detected across the relatively long optical paths used here. Though FTIR spectroscopy can detect dozens of different chemical species present in vegetation fire smoke, we focus our analysis on five key combustion products released preferentially during the pyrolysis (CH2O, flaming (CO2 and smoldering (CO, CH4, NH3 processes. We demonstrate that well constrained emissions ratios for these gases to both CO2 and CO can be derived for the backfire, headfire and residual smouldering combustion (RSC stages of these savannah fires, from which stage-specific emission factors can then be calculated. Headfires and backfires often show similar emission ratios and emission factors, but those of the RSC stage can differ substantially. The timing of each fire stage was identified via airborne optical and thermal IR imagery and ground-observer reports, with the airborne IR imagery also used to derive estimates of fire radiative energy (FRE, allowing the relative amount of fuel burned in each stage to be calculated and "fire averaged" emission ratios and emission factors to be determined. These "fire averaged" metrics are dominated by the headfire contribution, since the FRE data indicate that the vast majority

  4. EXTRACCIÓN DEL ACEITE DE LA SEMILLA DE PATILLA (Citrullus vulgaris POR LIXIVIACIÓN

    Directory of Open Access Journals (Sweden)

    Peggy Londoño

    2014-01-01

    Full Text Available L a extracción del aceite de la semilla de patilla c onsistió inicialmente en un estudio fisicoquímico de la semilla , con la finalidad de conocer su contenido nutricional mediante la realización de diferentes análisis como humedad, cenizas, grasas, fósforo, proteínas y carbohidratos . Posteriormente se procedió con la extracción del aceite utilizando el equipo de extracci ón sólido - líquido S oxhlet, empleando hexano como solvente mediante el diseño factorial del t ipo 2 3 . Luego de esto se realizó la caracterización del aceite crudo y ref inado siguiendo la metodologí a descrita por las normas COVENI N , donde el aceite presentó propiedades que le confieren gran potencial en la industria cosmética en la elaboración de ja bones. Por último se hizo un perfil lipídico por medio de una cromatografía de gases , arrojando un alto contenido de ácidos grasos insaturados (linoléico y oleíco que le dan la potencialidad de ser aplicado como un aceite apto para consumo humano de excelentes propiedades y calidad.

  5. Biofuels combustion.

    Science.gov (United States)

    Westbrook, Charles K

    2013-01-01

    This review describes major features of current research in renewable fuels derived from plants and from fatty acids. Recent and ongoing fundamental studies of biofuel molecular structure, oxidation reactions, and biofuel chemical properties are reviewed, in addition to combustion applications of biofuels in the major types of engines in which biofuels are used. Biofuels and their combustion are compared with combustion features of conventional petroleum-based fuels. Two main classes of biofuels are described, those consisting of small, primarily alcohol, fuels (particularly ethanol, n-butanol, and iso-pentanol) that are used primarily to replace or supplement gasoline and those derived from fatty acids and used primarily to replace or supplement conventional diesel fuels. Research efforts on so-called second- and third-generation biofuels are discussed briefly.

  6. MODELAMIENTO DE EXTRACCIÓN DEL ACEITE ESENCIAL DE Aloysia citriodora Y Schinus molle

    OpenAIRE

    Palacios Ambrocio, Andrianov Lenin; Universidad Nacional del Santa Ancash - Chimbote - Perú; Castillo Martinez, Williams Esteward; Universidad Nacional del Santa Ancash - Chimbote - Perú

    2015-01-01

    Los Aceites Esenciales tienen una importante demanda en la industria de alimentos, farmacéutica y de cosméticos. La presente investigación evalúa la cinética extracción de aceite esencial de Aloysia citriodora y Schinus molle evaluadas a dos caudales de vapor (4 y 6 Kg de vapor/h). Se empleó un equipo de extracción por arrastre de vapor a nivel piloto.El rendimiento de aceite esencial de las dos materia primas evaluadas se ajustan al modelo matemático de la cinética de Monod y la  cinética de...

  7. Aplicaciones del análisis de aceite usado en motores a diesel de uso marino

    OpenAIRE

    Muñoz, Carlos Neder; Marin Lopez, Jose Rolando

    2009-01-01

    El principal parámetro que determina la vida útil de un motor de combustión interna es el lu-bricante, el mismo que está compuesto usualmente de uno o dos tipos de aceites básico más un paquete de aditivos, para seleccionar un aceite de motor, se recomienda guiarse por el manual del fabricante de dicha máquina, en donde se indicará la viscosidad y el nivel de servicio o calidad que deberá tener el lubricante seleccionado. Dependerá de la correcta selección del lubricante que el desgaste de la...

  8. Diseño de un recipiente para la recogida de aceites vegetales usados

    OpenAIRE

    Clavel Marqués, Rodrigo

    2004-01-01

    Frente a los problemas originados en el medio ambiente por el vertido incontrolado de aceites domésticos usados, que normalmente se van por el fregadero, proponemos a través de este proyecto el diseño de un nuevo recipiente diseñado para la recogida de estos aceites, además de un posible sistema de recogida. Como ya sabemos, en muchos casos en el mundo del diseño, el proceso tiene una fuerte carga emocional, ya que se pretende provocar una reacción en el usuario, la mayor parte de las vece...

  9. Aceites volátiles de hojas y frutos de Pimenta guatemalensis (Myrtaceae de Costa Rica

    Directory of Open Access Journals (Sweden)

    Carlos Chaverri

    2015-03-01

    Full Text Available Pimenta es un género de plantas perteneciente a la familia Myrtaceae que contiene cerca de 15 especies, la mayoría ubicadas en las regiones del Caribe del Continente Americano, donde es utilizado con propósitos culinarios y medicinales. Las especies comerciales mejor conocidas son “pimienta de Jamaica” (P. dioica o P. officinalis y “bay-rum” (P. racemosa y existe muy poca información científica acerca de la especie P. guatemalensis. Cuando las hojas y frutos son triturados, desprenden un aroma de composición desconocida. El objetivo del presente estudio fue identificar la composición química de los aceites esenciales de las hojas y frutos de P. guatemalensis. La extracción de los aceites esenciales de P. guatemalensis, una especie arbórea silvestre en Costa Rica, se efectuó mediante el método de hidrodestilación a presión atmosférica, empleando un aparato de vidrio de tipo Clevenger. Se analizó la composición química de los aceites esenciales mediante cromatografía de gases con detector de ionización de flama (GC/FID y cromatografía de gases acoplada a un detector de masas (GC/MS y, utilizando índices de retención en una columna cromatográfica capilar tipo DB-5. En los aceites de hojas se identificaron 103 y en los de frutos 63 compuestos, correspondiendo a 96.8% y 86.1%, respectivamente, de los constituyentes totales. El aceite de las hojas está constituido principalmente por compuestos de naturaleza fenilpropanoide (72.9% y de hidrocarburos monoterpénicos y sesquiterpénicos (18.2%. Los componentes mayoritarios del aceite de las hojas se identificaron como eugenol (72.8%, β-cariofileno (8.2% y terpinoleno (3.0%. El aceite de los frutos está constituido principalmente por eugenol (74.7%, monoterpenos y sesquiterpenos oxigenados (7.3% principalmente óxido de cariofileno (3.3%. Este es el primer informe acerca de la composición química de aceites esenciales obtenidos a partir de esta especie vegetal.

  10. Índices de oxidación en aceites de algunas leguminosas del desierto sonorense

    Directory of Open Access Journals (Sweden)

    Vázquez-Moreno, L.

    2001-02-01

    Full Text Available The oxidation process of crude and refined oils from wild leguminous seeds: Prosopis juliflora (mezquite, Mimosa grahamii (gatuña, Acacia constricta, (vinorama Olneya tesota, (palo fierro Cercidium praecox (palo de brea and Parkinsonia aculeata (palo verde were evaluated during storage for 122 days, using corn and soybean oils as controls. Peroxide, Iodine, Acid and p-Anisidine values were determinated during 122 days of storage at room temperature. The wild leguminous raw oils showed results similar to those for the corn raw oil and lower than those of soybean raw oil. This behavior was similar for refinated oils. The rancid odor was detected after 5 days of storage in soybean oil and 40 days in vinorama oil, on the contrary, mezquite, palo verde and palo of brea oils presented this odor after 62 days, and for gatuña’s oil needed 135 days. Our results indicate that legume seed of Sonoran Desert could be a good alternative as source of oil.El proceso de oxidación fue evaluado durante el almacenamiento de los aceites crudos y refinados de las semillas de leguminosas silvestres: Prosopis juliflora (mezquite, Mimosa grahamii (gatuña, Acacia constricta (vinorama, Olneya tesota (palo fierro, Cercidium praecox (palo de brea y Parkinsonia aculeata (palo verde. Los aceites de maíz y soja fueron empleados como controles. Se determinó el índice de peróxido (I.P., de Yodo (I.I., de acidez (I.A, y valor de p-Anisidina (p-A durante 122 días de almacenamiento a temperatura ambiente. Los aceites crudos de leguminosas silvestres mostraron valores de estos índices similares a los del aceite de maíz crudo y menores que los del aceite de soja crudo. Este comportamiento también fue observado para los aceites refinados. El olor a rancio se presentó en el aceite de soja a los 5 días de almacenamiento, en el de vinorama a los 40 días, en el de mezquite, palo verde y palo de brea a los 62 días y en el de gatuña a los 135 días. Los valores

  11. Consumo de frutos secos y aceites vegetales en personas con diabetes mellitus tipo 1

    OpenAIRE

    Ferrer-García, Juan Carlos; Granell Vidal, Lina; Muñoz Izquierdo, Amparo; Sánchez Juan, Carlos

    2015-01-01

    Introducción: estudios recientes han demostrado los beneficios cardiovasculares de la dieta mediterránea enriquecida con aceite de oliva y frutos secos. Las personas con diabetes, que tienen un mayor riesgo de complicaciones cardiovasculares, podrían beneficiarse en gran medida de seguir ese tipo de patrón alimentario. Objetivos: análisis de la ingesta de grasas vegetales procedentes de frutos secos y aceites vegetales en pacientes con diabetes mellitus tipo 1 (DM1). Métodos: estudio transver...

  12. Actividad biológica de los aceites esenciales de Acmella ciliata (Kunth) Cass

    OpenAIRE

    Rincón Mejía, Carlos Andrés; Castaño Osorio, Jhon Carlos; Ríos Vázquez, Eunice

    2012-01-01

    Introducción: Acmella ciliata (Kunth) Cass. es una arvense nativa del norte de Suramérica conocida por su contenido de alcamidas alifáticas, se usa popularmente como anestésico y analgésico contra los dolores de muelas y de garganta. Objetivos: obtener, analizar y evaluar la actividad biológica de los aceites esenciales de las flores y hojas de Acmella ciliata (Kunth) Cass. Métodos: se obtuvieron los aceites esenciales de Acmella ciliata por hidrodestilación e hidrodestilación asistida por mi...

  13. Ingesta y evolución ponderal de ratas alimentadas con diferentes aceites crudos y fritos

    Directory of Open Access Journals (Sweden)

    Pérez-Granados, A. M.

    1998-04-01

    Full Text Available Olive oil, sunflower oil and palm olein, unused or used in repeated potato frying until the oils reached the limit of 25% of polar compounds (PC were used. Wistar rats were fed over 28 days diets containing 8% of: olive oil, olive oil from 48 fryings, olive oil from 69 fryings (25% PC, sunflower oil, sunflower oil from 48 fryings (25% PC, palm olein and palm olein from 80 fryings (25% PC Body weight and food intake were monitored weekly and food efficiency was calculated. At the end of the experiment the animals were sacrificed to separate the liver and calculate the hepatosomatic index. The consumption of frying oils did not modify food Intake, body weight food efficiency nor liver weight but hepatosomatic index was higher in rats consuming frying palm olein compared to unused palm olein.

    Se utilizaron aceites de oliva, girasol y oleína de palma, crudos o procedentes de frituras repetidas de patatas sin reposición de aceite hasta alcanzar el límite del 25% de compuestos polares (CP. Ratas Wistar se alimentaron durante 28 días con dietas que contenían un 8% de: aceite de oliva, aceite de oliva de 48 frituras, aceite de oliva de 69 frituras (25% CP, aceite de girasol, aceite de girasol de 48 frituras (25% CP, oleína de palma y oleína de palma de 80 frituras (25% CP. Peso e ingesta se controlaron semanalmente y se calculó el coeficiente de eficacia alimentaria. Al final del experimento los animales se sacrificaron para extraer los hígados y determinar el índice hepatosomático. El consumo de los aceites empleados en fritura no modificó la ingesta, peso, coeficiente de eficacia alimentaria ni el peso de los hígados, observándose únicamente un incremento del índice hepatosomático en los animales que ingirieron la oleína de palma frita frente a la cruda.

  14. Combustion means for solid fuels

    Energy Technology Data Exchange (ETDEWEB)

    Murase, D.

    1987-09-23

    A combustion device for solid fuel, suitable for coal, coke, charcoal, coal-dust briquettes etc., comprising:- a base stand with an opening therein, an imperforate heat resistant holding board locatable to close said opening; a combustion chamber standing on the base stand with the holding board forming the base of the combustion chamber; a wiper arm pivoted for horizontal wiping movement over the upper surface of the holding board; an inlet means at a lower edge of said chamber above the base stand, and/or in a surrounding wall of said chamber, whereby combustion air may enter as exhaust gases leave the combustion chamber; an exhaust pipe for the exhaust gases; generally tubular gas-flow heat-exchange ducting putting the combustion chamber and exhaust pipe into communication; and means capable of moving the holding board into and out of the opening for removal of ash or other residue. The invention can be used for a heating system in a house or in a greenhouse or for a boiler.

  15. Application of coal combustion residues to the stabilization/solidification of industrial wastes (IRIS); Desarrollo de un Proceso, a Escala Piloto de Inertizacion de Residuos Industriales con Cenizas Volantes

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    Stabilization/solidification (S/S) processes, also called inertization processes, are a group of techniques which employ additives to reduce the mobility of the hazardous components from the waste and make possible for the residue to be accepted for its disposal in a safe way. These processes, mainly applied to wastes that contain heavy metals (such as lead, zinc, cadminum, mercury, copper, nickel, titanium, chromium-III, chromium-VI, arsenic,....) change the waste into a solid-like material in which the metals are trapped (nets and matrix) by physical or chemical links. The IRIS Project, carried out by AICIA through the ECSC Coal Programme with the participation of two industrial partners (Sevillana de Electricidad and EGMASA, a public-owned company for waste treatment), has developed, at pilot scale, a new S/S process for inorganic industrial wastes that uses great quantities of fly ash in the place of other more commonly used and expansive reagents. A pilot plant for 200 kg/h has been designed, built and operated. This facility has allowed to add improvements and scientific foundations to existing S/S technology. It has also allowed to obtain industrial scale parameters for fixed and portable plants. Experiencie have been mainly carried out using fly ash from high quality coals, but types of ash have been tested coming from coals with a greater calcium content, from fluidised bed combustion boilers and from desulphurisation processes, giving very suitable characteristics for their application to S/S processes. The addition of fly ash (up to 30%) in the IRIS process improves the results in comparison with the S/S processes that use only cement, because the final pH obtained (8-11) does not allow amphoteric metallic ions to escape in the leachate. The same as other S/S processes, IRIS can be applied also to wastes that contain certain metals (chromium-VI, arsenic, for example) with specific pre-treatments (redox, for example). The efficiency of the IRIS treatment

  16. Tubular combustion

    CERN Document Server

    Ishizuka, Satoru

    2014-01-01

    Tubular combustors are cylindrical tubes where flame ignition and propagation occur in a spatially confined, highly controlled environment, in a nearly flat, elongated geometry. This allows for some unique advantages where extremely even heat dispersion is required over a large surface while still maintaining fuel efficiency. Tubular combustors also allow for easy flexibility in type of fuel source, allowing for quick changeover to meet various needs and changing fuel pricing. This new addition to the MP sustainable energy series will provide the most up-to-date research on tubular combustion--some of it only now coming out of private proprietary protection. Plentiful examples of current applications along with a good explanation of background theory will offer readers an invaluable guide on this promising energy technology. Highlights include: * An introduction to the theory of tubular flames * The "how to" of maintaining stability of tubular flames through continuous combustion * Examples of both small-scal...

  17. Advanced Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, Gordon R. [NETL

    2013-03-11

    The activity reported in this presentation is to provide the mechanical and physical property information needed to allow rational design, development and/or choice of alloys, manufacturing approaches, and environmental exposure and component life models to enable oxy-fuel combustion boilers to operate at Ultra-Supercritical (up to 650{degrees}C & between 22-30 MPa) and/or Advanced Ultra-Supercritical conditions (760{degrees}C & 35 MPa).

  18. Combustión y combustibles

    Directory of Open Access Journals (Sweden)

    Virella, A.

    1961-06-01

    Full Text Available Not availableLa ponencia trata de los combustibles generalmente empleados en los hornos rotativos de cemento Portland y, especialmente, de los problemas relacionados con los carbones pobres. En cualquier caso, hay que tener un conocimiento previo del poder calorífico del combustible que se pretende emplear, siendo de considerar antes el coste por unidad de calor que el coste por unidad de peso. Se describen el secado y la molienda de los carbones, señalando la tendencia actual de efectuar ambas operaciones simultáneamente, definiendo la aptitud para la pulverización y la determinación de la finura del polvo de carbón, por los métodos clásicos y por medio del permeabilímetro. Se expone en qué medida influyen la finura del combustible, el sistema de inyección, el estado del aire primario, su poder comburente, el exceso de aire y la proporción de cenizas en la determinación de la temperatura de la llama, su poder radiante, el flujo térmico y la posibilidad de obtener un clínker bien cocido. Se propugna por el empleo conjunto de aceites combustibles y carbones pobres como solución muy apropiada en la mayoría de los casos. Por último, se menciona la posibilidad de que se formen anillos en los hornos rotativos como consecuencia del empleo de carbones de alto contenido de cenizas, indicando algunas soluciones para evitar dicha perturbación.

  19. La diosa de Galera, fuente de aceite perfumado

    Directory of Open Access Journals (Sweden)

    Almagro-Gorbea, Martín

    2009-12-01

    Full Text Available The Goddess from Galera was found in a tomb of the Iberian cemetery of Tutugi (Granada dated c. 450 BC with a structure similar to the royal tomb of Pozo Moro. The Galera-Goddess is an alabaster sculpture dated in the VIII BC. from a Syrio-Phoenician workshop. It was a sacred vase for perfumed oil, devoted to the ritual anoint of god sculptures and sacred kings. The vase represents the goddess Astart, seated in her throne between two sphinxes and conceived as the Tree of Life. From her breasts come out the sacred perfumed oil which give life to the King, protect him magically and give him the Everlasting Life, as shown in oriental texts and iconography. Thereafter, it was not a keimélion brought trough Phoenicians trade, but a sacred object arrived to the Far West from a Nord-Syrian royal context trough the koiné of the Phoenician colonisation. As it was found in an Iberian royal tomb, it documents the origin of the ideology and ritual from the Tartessian and Iberian kings in the Orientalaizing Period.La llamada Diosa de Galera apareció en una tumba real de la necrópolis ibérica de Tutugi (Granada, comparable a la de Pozo Moro, aunque de mediados del siglo V a.C. Es una escultura de alabastro labrada en un taller áulico sirio-fenicio del siglo VIII a.C. para servir como vaso sagrado de aceite perfumado destinado en exclusiva a la unción ritual de estatuas de divinidad y/o de reyes divinizados. La diosa Astart, entronizada entre dos esfinges, aparece concebida como Árbol de la Vida, pues de sus pechos brota el divino néctar o ambrosía perfumado que da al Rey la vida, le protege mágicamente y le garantiza la vida eterna en el Más Allá, según indican textos y representaciones orientales. Se trata de un objeto ritual sacro de ámbito regio, no de un simple keimélion traído por los fenicios. Sería la divinidad protectora de algún miembro de estirpe real nordsirio llegado a Occidente a través de la koiné colonial fenicia. Su

  20. Caracterización y perfil lipídico de aceites de microalgas

    Directory of Open Access Journals (Sweden)

    Lesly Tejeda-Benítez

    2015-05-01

    Full Text Available El uso creciente del biodiésel ha impulsado la búsqueda de nuevas materias primas, dentro de las que se destacan las microalgas. En esta investigación se estudió el cultivo de las microalgas Chlorella sp. y Dunaliella salina bajo diferentes condiciones de pH y concentración de nitrógeno (mgL-1, y la caracterización de los aceites obtenidos, con el fin de evaluar su potencial uso como materia prima en la producción de biodiésel. La D. salina alcanzó una máxima concentración celular de 1.15x106 células mL-1 en 6 días de cultivo en unas condiciones de 8.5 pH y 0.1 mg L-1 concentración de nitrógeno, mientras que Chlorella sp. presentó una máxima concentración celular de 2.6x107 células mL-1 en 14 días de cultivo en unas condiciones de 7.5 pH y 0.1 mg L-1 concentración de nitrógeno. La extracción de aceite intracelular de las microalgas cultivadas bajo las mejores condiciones de crecimiento celular se realizó empleando el método modificado de Bligh & Dyer. Al determinar el perfil de ácidos grasos de los aceites extraídos de ambas microalgas, se  encontraron en mayor proporción dos ácidos grasos insaturados: ácido linolénico y ácido oleico. En el aceite de D. salina se encontró una concentración de 51% p/p de ácido linolénico, mientras que para el aceite de Chlorella sp. fue de 39% p/p. Con relación al ácido oleico, el aceite de Chrorella sp. presentó una concentración de 35% p/p, superior al aceite de D. salina, con 25% p/p.

  1. Oportunidades comerciales para el aceite de oliva de Castilla-La Mancha

    Directory of Open Access Journals (Sweden)

    Olivas, Raquel

    2009-12-01

    Full Text Available Quality olive oils produced in Castilla-La Mancha are difficult to commercialize in the national and international markets due to increasing competition among olive oil companies and their easy replacement by other cheaper seed oils. To increase competitiveness, consumer preference must be discovered. Therefore, 420 surveys were made on vegetable oil consumers in the Madrid metropolitan area in December, 2006. It was detected by means of the conjoint analysis technique, simulation and analysis logit that the type of vegetable oil preferred by consumers was the extra virgin olive oil. Some market opportunities seem to exist for the organic olive oil produced in Castilla-La Mancha and consumers’ maximum willingness to pay for organic olive oil with regard to the conventional oil is 13.1%. In addition to this, and with the aim of contributing to the commercialization of the organic olive oil produced in Castilla-La Mancha, the Regional Government of Castilla-La Mancha (Spain could promote the creation of the Protected Geographical Indication of Castilla-La Mancha Organic Olive Oils.El aceite de oliva producido en Castilla-La Mancha tiene una difícil comercialización tanto por el aumento de la competitividad nacional como internacional así como por su fácil sustitución por otros aceites de semillas más baratos. Para incrementar su competitividad, resulta necesario conocer cuáles son las preferencias de los consumidores. Para ello, se realizaron 420 encuestas en diciembre de 2006 a consumidores de aceite en el área metropolitana de Madrid. Mediante las técnicas de análisis conjunto, simulación y logia, se ha detectado que el tipo de aceite preferido por los consumidores es el de oliva virgen extra, que parecen existir oportunidades de mercado para los producidos ecológicamente en Castilla-La Mancha y que la máxima disposición al pago por un aceite de oliva ecológico, respecto a otro convencional, es del 13,1%. Adicionalmente a lo

  2. Actividad repelente de aceites esenciales contra las picaduras de Lutzomyia migonei (Diptera: Psychodidae

    Directory of Open Access Journals (Sweden)

    Elsa Nieves

    2010-12-01

    Full Text Available Los repelentes naturales de extractos de plantas han mostrado eficacia contra diferentes especies de insectos. El presente estudio evaluó la acción repelente de aceites esenciales extraídos de ocho especies de plantas contra las picaduras de Lutzomyia migonei, vector de Leishmania. Los aceites esenciales se obtuvieron por hidrodestilación, utilizando una trampa de Clevenger, a partir de Hyptis suaveolens, Pimenta racemosa, Piper marginatum, Monticalia imbricatifolia, Pseudognaphalium caeruleocanum, Espeletia shultzii, Plectranthus amboinicus y Cinnamomun zeylanicum. Los ensayos de repelencia se realizaron sobre humanos en condiciones de laboratorio, frente a hembras de L. migonei provenientes de colonia, utilizando el método de la mano en la jaula. Los aceites con efecto repelente también se ensayaron con distintos voluntarios y concentraciones. Se determinó el porcentaje de protección y el tiempo de protección. Los resultados revelaron que el aceite de P. caeruleocanum y C. zeylanicum fueron los más efectivos. El aceite de P. amboinicus presentó efecto de repelencia satisfactorio, sin embargo, ocasionó picazón y toxicidad en la piel. Los aceites de P. marginatum, H. suaveolens y P. racemosa no evidenciaron efecto repelente; el resto de los aceites presentaron repelencia significativa en grado variable. Los aceites de P. caeruleocanum y C. zeylanicum mostraron un 95% de protección de 3h contra las picaduras de L. migonei. El aceite de P. caeruleocanum presentó el mayor tiempo de protección, de más de 4h y de 2h en concentraciones de 50% y 10%, respectivamente. Los resultados sugieren que el aceite P. caeruleocanum podría ser un potencial candidato como repelente natural contra la picadura de dípteros posibles transmisores de Leishmania.Repellent activity of plant essential oils against bites of Lutzomyia migonei (Diptera: Psychodidae. Natural repellents from plant extracts have demonstrated good efficacy against bites of some

  3. Insecticidal Activity of Peumus boldus Molina Essential Oil against Sitophilus zeamais Motschulsky Actividad Insecticida del Aceite Esencial de Peumus boldus Molina sobre Sitophilus zeamais Motschulsky

    Directory of Open Access Journals (Sweden)

    Jessica Betancur R

    2010-09-01

    Full Text Available In stored grains, the main agents diminishing production are insects, which can produce losses between 20% and 80% before harvest or under storage. The insecticidal properties of the essential oil of fresh leaves of Peumus boldus Molina against maize weevil (Sitophilus zeamais Motschulsky adults were determined under laboratory conditions. The highest mortality (100% was achieved at 4% concentration by contact with a treated glass surface. The same concentration in impregnated corn (Zea mays L. grain, resulted in 98.7% mortality. Mortality by fumigant action at 6 h was 100% with 35 µL oil in 0.15 L (air volume. Concentrations 1, 2 and 4% of essential oil produced 0% F1 adult emergence. At 10 d of residual effect, the 4% concentration reached 63.7% mortality. All treatments were repellent to adults of S. zeamais and corn grain germination was not affected by any treatment.Los principales agentes que disminuyen la producción en los granos almacenados son los insectos, antes de la cosecha y en el almacenamiento pueden causar pérdidas de 20 a 80%. Se evaluaron las propiedades insecticidas del aceite esencial de hojas frescas de Peumus boldus Molina para el control de adultos de gorgojo del maíz (Sitophilus zeamais Motschulsky en laboratorio. La mayor mortalidad (100% por contacto con una superficie de vidrio tratada se obtuvo con la concentración de 4%. Esta misma concentración produjo 98,7% de mortalidad en exposición a grano de maíz (Zea mays L. tratado. El efecto fumigante a las 6 h de exposición fue 100% con 35 µL de aceite en 0,15 L (volumen de aire. Con las concentraciones de 1, 2 y 4% de aceite esencial, el porcentaje de emergencia de la F1 fue 0%. A los 10 d de efecto residual se alcanzó 63,7% de mortalidad con la concentración de 4%. Todos los tratamientos fueron repelentes para adultos de S. zeamais y ningún tratamiento afectó la germinación de los granos.

  4. Handling of Solid Residues

    International Nuclear Information System (INIS)

    Medina Bermudez, Clara Ines

    1999-01-01

    The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

  5. Technological alternatives for the handling of high viscosity heavy crude oil and of petroleum residuals; Alternativas tecnologicas para el manejo de crudos pesados de alta viscosidad y residuales de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez S, Ramon; Peralta M, Maria Vita; Gonzalez Santalo, Jose M; Herrera V, J Ramon; Arriola M, Alejandro M; Manzanares P, Emilio; Romo M, Cesar A; Palacios L, Elvia M [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2006-07-01

    This work presents the technological capacity that, through the years, has been developed in emulsions of heavy oil in water preparations, as well as the potential application that this technology has in the electrical sector and the problem reduction during the extraction and handling of high viscosity heavy oils. Within this technological development it first appears the process for the formation of emulsions of residual petroleum within lots, followed by the preparation of emulsions in a continuous way within a laboratory model, and finally the production in greater scale in a pilot plant, including more and more adequate tense-actives for the formation of emulsions. Also experimental systems are presented to execute static stability and dynamic tests in different conditions, pumping tests for the handling of these emulsions and burning tests for their combustion. All of this with the purpose of consolidating the technology of residual petroleum emulsions as a profitable alternative that replaces the heavy fuel oil and to solve specific problems of the oil industry, among other benefits. [Spanish] Este trabajo exhibe la capacidad tecnologica que, a traves de los anos, se ha desarrollado en la preparacion de emulsiones de aceites pesados en agua; asi como el potencial de aplicacion que tiene dicha tecnologia en el sector electrico y la reduccion de problemas durante la extraccion y manejo de aceites pesados de alta viscosidad. Dentro de este desarrollo tecnologico figura primero el proceso para la formacion de emulsiones de residuales de petroleo dentro de lotes, seguido por la preparacion de emulsiones en continuo dentro de un laboratorio modelo, y finalmente la produccion a mayor escala en una planta piloto, incluyendo cada vez mas adecuados tenso-activos para la formacion de las emulsiones. Tambien se presentan sistemas experimentales para ejecutar pruebas de estabilidad estatica y dinamica en diferentes condiciones, pruebas de bombeo para el manejo de estas

  6. High Combustion Research Facility

    Data.gov (United States)

    Federal Laboratory Consortium — At NETL's High-Pressure Combustion Research Facility in Morgantown, WV, researchers can investigate new high-pressure, high-temperature hydrogen turbine combustion...

  7. Combustion Research Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Combustion Research Laboratory facilitates the development of new combustion systems or improves the operation of existing systems to meet the Army's mission for...

  8. Combustion chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N.J. [Lawrence Berkeley Laboratory, CA (United States)

    1993-12-01

    This research is concerned with the development and use of sensitivity analysis tools to probe the response of dependent variables to model input variables. Sensitivity analysis is important at all levels of combustion modeling. This group`s research continues to be focused on elucidating the interrelationship between features in the underlying potential energy surface (obtained from ab initio quantum chemistry calculations) and their responses in the quantum dynamics, e.g., reactive transition probabilities, cross sections, and thermal rate coefficients. The goals of this research are: (i) to provide feedback information to quantum chemists in their potential surface refinement efforts, and (ii) to gain a better understanding of how various regions in the potential influence the dynamics. These investigations are carried out with the methodology of quantum functional sensitivity analysis (QFSA).

  9. CARACTERIZACIÓN FÍSICO-QUÍMICA DEL ACEITE ESENCIAL DE ALBAHACA. II

    Directory of Open Access Journals (Sweden)

    Elizabeth Murillo

    2008-03-01

    Full Text Available Se estudió la composición química del aceite esencial de Ocimum americanum L. (albahaca querendona morada obtenido por hidrodestilación de vegetales recolectados en Chapetón-Ibagué. El análisis realizado por cromatografía de gases de alta eficiencia/detector selectivo de masas (HRGC/MSD reveló que la esencia está constituida en un 85,4% por cinamato de metilo y un 5% de estragol. Adicionalmente, se caracterizó el aceite esencialmediante la determinación de la densidad, índice de refracción, pH, solubilidad y los espectros IR y UV.

  10. Managing ash from the combustion of solid waste

    International Nuclear Information System (INIS)

    Hauser, R.

    1992-01-01

    This paper reports that with millions of tons of refuse being combusted each year, increasing concern over the environment impact of the residue produced has caused both regulators and the resource recovery industry to address the technical and regulatory issues relating to the safe handling and disposal of ash. The basic issue concerning solid waste combustion ash management in this country is how, based on past, recent, and ongoing scientific research, solid waste combustion ash should be handled. Typically, refuse contains approximately 20 to 25 percent residue, which is collected either on grates at the bottom of the combustion chamber or filtered from the exhaust gases by the air pollution control equipment. The fly ash component of the total residue stream is between 10 and 30 percent of the total residue while the bottom ash content ranges from 70 to 90 percent of the total weight, depending upon the air pollution control equipment utilized, especially acid gas scrubbing equipment

  11. Propiedades de los aceites vegetales modificados por hidrogenacion, interesterificación y fraccionamiento

    Directory of Open Access Journals (Sweden)

    Grompone, M. A.

    1992-12-01

    Full Text Available The advent of techniques of chemical processing (hydrogenation and interesterification and physical processing (fractionation provides the manufacturer the capacity of modifying one or many physicochemical properties of an oil or fat. In the present paper the influence of the chemical interesterification and thermal fractionation without solvent on the physical properties (melting point, solid fat index of the products obtained by partial hydrogenation of soybean oil is studied. Properties of mixtures of partially hydrogenated soybean oil and totally hydrogenated coconut oil are also determined. The examples studied show that knowing the changes produced by current modification methods is useful to design fatty products for specific purposes.

    El advenimiento de técnicas de procesamiento químico (hidrogenación e interesterificación y físico (fraccionamiento proveen al industrial de la capacidad de modificar una o varias de las propiedades fisicoquímicas de una grasa o aceite. En este trabajo se estudia de un modo sistemático la influencia de la interesterificación química y del fraccionamiento térmico sin solventes sobre las propiedades físicas (punto de fusión, índice de grasa sólida de los productos obtenidos por hidrogenación parcial de aceite de soya. También se determinan las propiedades de mezclas de aceite de soya parcialmente hidrogenado con aceite de coco totalmente hidrogenado. Los ejemplos estudiados muestran que el conocimiento de los cambios ocasionados por los procesos de modificación corrientes son útiles para diseñar productos grasos para fines específicos.

  12. La Antracnosis del olivo y su efecto en la calidad del aceite

    Directory of Open Access Journals (Sweden)

    Moral, J.

    2014-06-01

    Full Text Available Olive (Olea europaea subsp. europaea var. europaea is one of the first domesticated and cultivated trees that is widely distributed in the Mediterranean regions. The Anthracnose, caused by the two complex fungal species Colletotrichum acutatum and C. gloeosporioides, is the most important disease adversely affecting the olive oil quality. Even so, the effect of Anthracnose on oil quality is largely unknown and many questions remain unanswered. This offers a unique opportunity to study how Colletotrichum species, cultivars, infection type (latent or visible and severity, and other factors that may affect different parameters of oil quality, such us acidity, peroxide value, K232, K270, phenolic compounds, or alkyl esters. This review focuses on the current knowledge of the biology, epidemiology, and management of Anthracnose and its effect on olive oil quality.El olivo (Olea europaea subsp. europaea var. europaea es uno de los primeros cultivos leñosos domesticados. Actualmente el olivo se encuentra ampliamente distribuido por todas las regiones de clima mediterráneo. La Antracnosis, causada por las especies complejas Colletotrichum acutatum y C. gloeosporioides, es la enfermedad del olivo que más afecta a la calidad del aceite. Aun así, el efecto de la Antracnosis en la calidad del aceite es ampliamente desconocido. Por lo que creemos esencial que se afronten estudios encaminados a dilucidar el efecto de las especies del patógeno, el cultivar de olivo y el tipo (latente o visible y severidad de las infecciones de la aceituna en los distintos parámetros de calidad del aceite como la acidez, índice de peróxidos, K232, K270, compuestos fenólicos o ésteres alquílicos. Esta revisión presenta los conocimientos actuales sobre la biología, epidemiología, control, y efecto en la calidad del aceite de la Antracnosis del olivo.

  13. nfluencia de antioxidantes en la estabilidad oxidativa del aceite de chia ( Salvia hispanica L . por rancimat

    Directory of Open Access Journals (Sweden)

    Eudes Villanueva

    2017-01-01

    Full Text Available La rancidez oxidativa, conocida como autooxidación, es la principal causa de deterioro d e aceites y grasas, la que puede controlarse mediante el empleo de antioxidantes incrementando la estabilidad oxidativa y vida en anaquel. El aceite de chía es rico en ácidos grasos poli - insaturados (PUFAs, particularmente en omega - 3 (ω - 3 y omega - 6 (ω - 6 beneficiosas para la salud humana, pero también los PUFAs favorecen a la reacción de autooxidación. E l objetivo de e ste trabajo fue determinar el efecto de antioxidantes sintéticos y de origen natural a concentración de 200 ppm de etoxiquina (EQ, butilhi drixianisol (BHA, butilhidroxitolueno (BHT y fortium (FT, sobre el índice de estabilidad oxidativa (OSI del aceite de chía por rancimat a diferentes temperaturas (90, 100 y 110 °C. El método rancimat está incluido en los estándares AOCS Cd 12b - 92, deb ido a su facilidad de uso y reproducibilidad permite evaluar el OSI en un periodo relativamente corto. Los resultados muestran que entre el BHT y EQ, así como entre el BHA y FT no presentan diferencia estadísticamente significativa (p ≤ 0,05. Siendo el BH T el antioxidante que incrementó en mayor proporción el OSI del aceite de chía, con un factor de protección (FP de 1,30, 1,26 y 1,29 para las diferentes temperaturas aplicadas y con una energía de activación (Ea de 82,75 kJ/mol, por lo tanto, se recomend aría su uso .

  14. Obtención de una formulación de barniz con base en aceite de soya a escala de laboratorio

    OpenAIRE

    Bravo Silva, Ana María; Cardona Arango, Rafael

    2009-01-01

    En este proyecto se desarrollaron cuatro formulaciones de barniz para madera con base en Aceite de Soya, por medio de un proceso de mezcla a escala de laboratorio; este proceso inició con la refinación de Aceite de Soya crudo, el cual fue desgomado y neutralizado, a su vez fue caracterizado tanto en su estado crudo como refinado, para esto se determinó su índice de acidez, yodo y saponificación respectivamente. Las cuatro formulaciones cuentan con Aceite de Soya, aceite de linaza, aditivos se...

  15. Determinación de algunos parámetros de pureza en aceites de oliva. Resultados de un estudio colaborativo

    Directory of Open Access Journals (Sweden)

    Moreda, W.

    1995-10-01

    Full Text Available The results of a collaborative study with the participation of Governmental and Olive Oil Industry laboratories is presented. This study was carried out to determine the precision of the analytical methods used for quantifying certain components of olive oils. Samples of virgin olive oil, olive oil and residue olive oil were analysed for total sterols, sterolic composition, trans isomers from fatty acids, waxes and stigmastadienes, using the analytical methods included in the Commission Regulation EEC 2568/91 of the European Union and modifications therein, and in Document TC20/11 of the International Olive Oil Council (1993. The results have been statistically procesed according to the standard ISO 5725-1986 (E.

    Se presentan los resultados de un estudio colaborativo realizado con la participación de laboratorios de la Administración Pública y de industrias del Sector Oleícola con el objeto de determinar la precisión de los métodos analíticos que se utilizan para la cuantificación de ciertos componentes de los aceites de oliva. Esteroles totales, composición esterólica, isómeros trans de ácidos grasos, ceras y estigmastadienos han sido determinados en muestras de aceites de oliva virgen, de oliva y de orujo de oliva, mediante la aplicación de los métodos analíticos indicados en el reglamento CEE 2568/91 de la Unión Europea y posteriores modificaciones, así como en el Documento TC20/11 del Consejo Oleícola Internacional (1993. Se ha efectuado un análisis estadístico de los resultados de acuerdo con la norma ISO 5725-1986 (E.

  16. Extracción y caracterización de aceite de semillas de zapallo

    Directory of Open Access Journals (Sweden)

    Sanín Ortiz Grisales

    2009-07-01

    Full Text Available Se seleccionaron 79 introducciones de zapallo (Cucurbita moschata Duch teniendo en cuenta el contenido de extracto etéreo (EE de las semillas. El EE fue estable física y químicamente, con propiedades organolépticas óptimas de aceite comestible, no presentó características de rancidez; aceite semisecante (122.90 mg/g de KOH.; índice de acidez 3.25 mg/g de KOH; la prueba presuntiva de yodo supone presencia de polinsaturación y sin formación de cristales. La composición de ácidos grasos mostró: palmítico C16:0 (25.11 - 36.94%; esteárico C18:0 (10.79 - 13.37%; linoleíco C18:2 (48.23 - 62.41%; linolénico C18:3 (0.66% y araquídico C20:0 (0.53 - 0.78%. El aceite de semilla de zapallo contiene 55.28% de ácidos grasos insaturados con una cantidad apreciable de linoleíco (55.11%. La torta de semilla presentó proteína (51.11 ± 0.95% y energía (4604. 66 ± 134.08 kcal/kg.

  17. Diseño de un equipo de pruebas rápidas para aceites usados

    Directory of Open Access Journals (Sweden)

    Juan Carlos Delgado Sanabria

    2016-01-01

    Full Text Available El presente trabajo tiene como objetivo presentar el proceso de diseño y la construcción de un equipo de pruebas rápidas para el análisis de aceites usados de motores. El equipo que permite evaluar el estado de degradación y contaminación de una muestra de aceite usado mediante los ensayos de crepitación, mancha de aceite, viscosidad y contenido de partículas consta de cuatro aparatos: placa de calentamiento, generador de manchas, viscosímetro de caída de bolas y detector de partículas ferrosas. El aporte fundamental del trabajo lo constituyen los dispositivos y métodos ideados tanto para medir con exactitud el tiempo de caída de la esfera del viscosímetro de bolas como para la detección de partículas ferromagnéticas. El equipo ha producido resultados satisfactorios comparados con los obtenidos en pruebas de laboratorio.

  18. Efecto de la poda sobre la cantidad y el rendimiento del aceite esencial de Laurus nobilis

    Directory of Open Access Journals (Sweden)

    Ana María Callejas-Leguizamon

    2013-07-01

    Full Text Available Objetivo. Conocer el comportamiento de la planta de laurel con diferentes podas, en cuanto a su rendimiento y cantidad de aceite esencial para satisfacer las demandas del mercado. Materiales y métodos. Se monitorearon 48 plantas, ubicadas en el municipio de Nuevo Colón, Boyacá, en un diseño completamente al azar, con tres tratamientos (deshoje, despunte y el testigo sin poda en 5 estadios fenológicos, con cuatro repeticiones. Se evaluó la respuesta en cuanto a tres solventes usados en la extracción y diferentes tipos de poda. Resultados. El hexano fue el solvente que permitió mayor extracción de aceite esencial de las hojas de laurel, seguido de etanol y cloroformo-metanol, respectivamente. Asimismo, en los diferentes tratamientos de poda se demostró que la mayor cantidad de aceite esencial (p≤0,01 se obtuvo en hojas de laurel con despunte, mientras que con deshoje se obtuvo la menor cantidad. Analizando el rendimiento, se encontraron rendimientos (2,32% en las hojas de laurel con despunte, seguido de las plantas testigo (2,05% y por último las plantas con deshoje (1,24%. Conclusiones. El despunte, como práctica agronómica, en laurel representa mayores beneficios al productor y es una alternativa de valor agregado.

  19. Efecto del aceite esencial de Eucalyptus citriodora sobre el metabolismo energético mitocondrial

    Directory of Open Access Journals (Sweden)

    Luis Carlos Vesga

    2014-05-01

    Full Text Available Con el fin de contribuir al conocimiento de su actividad a nivel celular, se evaluó el mecanismo de acción del aceite esencial de Eucalyptus citriodora (Fam. Myrtaceae sobre la bioenergética mitocondrial, su efecto sobre la velocidad de consumo de oxígeno de mitocondrias energizadas (estados 3 y 4 y su coeficiente de control respiratorio (CCR. Además, se analizó la actividad de los complejos de la cadena respiratoria usando técnicas espectrofotométricas. Los resultados obtenidos indican que el aceite esencial de E. citriodora aumenta la velocidad del consumo de oxígeno en los estados 3 y 4, disminuye el CCR, desacopla la fosforilación oxidativa, aumenta la actividad de la citocromo c oxidasa y aumenta la actividad ATPasa en mitocondrias íntegras, a partir de la concentración de 10 μg/mL. Estos resultados sugieren que el aceite esencial o sus metabolitos afectan el funcionamiento normal del transporte de electrones de la cadena respiratoria y la síntesis de ATP.

  20. Rotary combustion device

    NARCIS (Netherlands)

    2008-01-01

    Rotary combustion device (1) with rotary combustion chamber (4). Specific measures are taken to provide ignition of a combustible mixture. It is proposed that a hollow tube be provided coaxially with the axis of rotation (6), so that a small part of the mixture is guided into the combustion chamber.

  1. COMBUSTION OF BIOMASS AND CHARCOAL MADE FROM BABASSU NUTSHELL

    Directory of Open Access Journals (Sweden)

    Thiago de Paula Protásio

    2017-03-01

    Full Text Available In recent years, studies have examined the use of lignocellulosic wastes for energy generation. However, there is a lack of information on the combustibility of the residual biomass, especially the bark and charcoal of babassu nut. In this study, thermogravimetric analysis (TGA, differential thermal analysis (DTA and differential scanning calorimetry (DSC were used to achieve the following objectives: to evaluate the combustion of the residual biomass from the babassu nut; to evaluate the combustion of charcoal produced from this biomass, considering different final carbonization temperatures; and to determine the effect of the final carbonization temperature on the thermal stability of charcoal and on its performance in combustion. Thermal analyses were performed in synthetic air. In order to evaluate the characteristics of charcoal combustion and fresh biomass, the ignition temperature (Ti, the burnout temperature (Tf, characteristic combustion index (S, ignition index (Di, time corresponding to the maximum combustion rate (tp, and ignition time (tig were considered. The combustion of the babassu nutshell occurred in three phases and it was observed that this lignocellulosic material is suitable for the direct generation of heat. The increase in the final carbonization temperature caused an increase in the ignition temperature, as well as in the burnout temperature, the ignition time and the time corresponding to the maximum combustion rate. The results indicate that the increase in the carbonization temperature causes a decrease in combustion reactivity and, consequently, the charcoals produced at lower temperatures are easier to ignite and exhibit better performance in ignition.

  2. Proceso de sacarificación y fermentación simultáneas para la conversión de la fracción celulósica del residuo de la extracción del aceite de oliva en etanol

    Directory of Open Access Journals (Sweden)

    Ballesteros, M.

    2002-09-01

    Full Text Available In this work, the residue generated in the new two-step centrifugation process for olive oil extraction is assessed for the production of bioethanol. Both olive pulp and fragmented stones fractions comprised in such residue are analyzed and tested at laboratory scale for bioconversion to ethanol by a simultaneous saccharification and fermentation (SSF process. Firstly, optima conditions for the enzymatic hydrolysis step of steam-exploded pretreated sustrates were determined. Then, simultaneous saccharification and fermentation process was assayed using the thermotolerant yeast Kluyveromyces marxianus in different assay conditions. For the selected conditions, 9 kg of unpretreated pulp or 6 kg of pretreated fragmented stones (both based on dry matter would be necessary to obtain 1 liter of ethanol.En el presente trabajo se estudia la producción de etanol-combustible a partir de la celulosa contenida en las distintas fracciones (pulpa y fragmentos de huesos que componen el residuo de la extracción de aceite de oliva mediante un proceso en dos fases. El trabajo ha consistido en una caracterización de las dos fracciones y en el estudio de la producción de etanol mediante un proceso de hidrólisis enzimática y fermentación simultáneas (SFS, a escala de laboratorio. Se ha estudiado el efecto que un pretratamiento termomecánico de explosión a vapor, previo a la etapa de hidrólisis enzimática y fermentación, tiene sobre la acción del complejo celulolítico. Por último, se han determinado las condiciones óptimas de ensayo para la sacarificación y fermentación simultáneas utilizando una cepa termotolerante de Kluyveromyces marxianus. En las condiciones de ensayo óptimas, serían necesarios 9 kg. de pulpa o 6 kg. de hueso pretratado (ambos sobre peso seco, para obtener 1 litro de etanol.

  3. Estudio de la composición química de la semilla y aceite seminal de Cichorium intybus L. (Achicoria

    Directory of Open Access Journals (Sweden)

    Nolasco, S. M.

    1996-12-01

    Full Text Available Seeds from Cichorium intybus L harvested at Olavarría (Buenos Aires, Argentine were defatted with petroleum ether (60°-80° and the raw oil obtained with a yield of 13.3% dry basis. The crude oil was examined in their physicochemical characteristics had refractive index of 1.4576 (at 25°, iodine value of 124.3, saponification index of 191,4, unsaponifiable matter of 5.3 % and free fatty acid content of 6.0 (mg KOH/g. Gas chromatographic analysis of the oil revealed high levels of linoleic acid (59.8%, nearly 21% of saturated acids.
    The residual seed meal contained 16.9% of crude protein, with a low value of available lysine (1.37g/16 g N. Total and phytic acid phosphorous, calcium, ash, crude fiber, sugar, polysaccharides (non presence of starch and residual lipids contents are reported.

    Semillas de Cichorium intybus L (Achicoria cosechadas en Olavarría (prov. de Buenos Aires, Argentina se agotaron con éter de petróleo (60°-80°, obteniendo el aceite crudo con un rendimiento del 13,3% (base seca. El aceite crudo se examinó en sus características fisicoquímicas (índice de refracción: 1.4576 (a 25°, índice de iodo: 124.3, índice de saponificación: 191.4, insaponificable: 5.3%, índice de acidez: 6.0 (mgKOH/g y composición acídica. El análisis por cromatografía gaseosa de los esteres metílicos reveló un alto porcentaje de ácido linoleico (59,8%, alrededor de un 21% de ácidos saturados.
    La harina residual de extracción presentó un 16.9% b.s. de proteína cruda, con un bajo contenido en lisina disponible de 1,37 g/16 g N. Se informan valores de fósforo total y de ácido fítico, cenizas, calcio, fibra cruda, hidratos de carbono y lípidos residuales.

  4. Combustion 2000

    Energy Technology Data Exchange (ETDEWEB)

    A. Levasseur; S. Goodstine; J. Ruby; M. Nawaz; C. Senior; F. Robson; S. Lehman; W. Blecher; W. Fugard; A. Rao; A. Sarofim; P. Smith; D. Pershing; E. Eddings; M. Cremer; J. Hurley; G. Weber; M. Jones; M. Collings; D. Hajicek; A. Henderson; P. Klevan; D. Seery; B. Knight; R. Lessard; J. Sangiovanni; A. Dennis; C. Bird; W. Sutton; N. Bornstein; F. Cogswell; C. Randino; S. Gale; Mike Heap

    2001-06-30

    . To achieve these objectives requires a change from complete reliance of coal-fired systems on steam turbines (Rankine cycles) and moving forward to a combined cycle utilizing gas turbines (Brayton cycles) which offer the possibility of significantly greater efficiency. This is because gas turbine cycles operate at temperatures well beyond current steam cycles, allowing the working fluid (air) temperature to more closely approach that of the major energy source, the combustion of coal. In fact, a good figure of merit for a HIPPS design is just how much of the enthalpy from coal combustion is used by the gas turbine. The efficiency of a power cycle varies directly with the temperature of the working fluid and for contemporary gas turbines the optimal turbine inlet temperature is in the range of 2300-2500 F (1260-1371 C). These temperatures are beyond the working range of currently available alloys and are also in the range of the ash fusion temperature of most coals. These two sets of physical properties combine to produce the major engineering challenges for a HIPPS design. The UTRC team developed a design hierarchy to impose more rigor in our approach. Once the size of the plant had been determined by the choice of gas turbine and the matching steam turbine, the design process of the High Temperature Advanced Furnace (HITAF) moved ineluctably to a down-fired, slagging configuration. This design was based on two air heaters: one a high temperature slagging Radiative Air Heater (RAH) and a lower temperature, dry ash Convective Air Heater (CAH). The specific details of the air heaters are arrived at by an iterative sequence in the following order:-Starting from the overall Cycle requirements which set the limits for the combustion and heat transfer analysis-The available enthalpy determined the range of materials, ceramics or alloys, which could tolerate the temperatures-Structural Analysis of the designs proved to be the major limitation-Finally the commercialization

  5. Reduced NOX combustion method

    International Nuclear Information System (INIS)

    Delano, M.A.

    1991-01-01

    This patent describes a method for combusting fuel and oxidant to achieve reduced formation of nitrogen oxides. It comprises: It comprises: heating a combustion zone to a temperature at least equal to 1500 degrees F.; injecting into the heated combustion zone a stream of oxidant at a velocity within the range of from 200 to 1070 feet per second; injecting into the combustion zone, spaced from the oxidant stream, a fuel stream at a velocity such that the ratio of oxidant stream velocity to fuel stream velocity does not exceed 20; aspirating combustion gases into the oxidant stream and thereafter intermixing the aspirated oxidant stream and fuel stream to form a combustible mixture; combusting the combustible mixture to produce combustion gases for the aspiration; and maintaining the fuel stream substantially free from contact with oxidant prior to the intermixture with aspirated oxidant

  6. EVALUACIÓN DE LA ACTIVIDAD ANTIOXIDANTE DE ACEITES ESENCIALES EN EMULSIONES DEGRADADAS POR RADIACIÓN ULTRAVIOLETA

    Directory of Open Access Journals (Sweden)

    Geovanna Tafur

    2008-03-01

    Full Text Available En este trabajo se evaluaron las actividades antioxidantes in vitro de los aceites esenciales de Origanum vulgare L., Rosmarinusofficinalis L. y Coriandrum sativum L., en emulsiones de agua en aceite (Ag/Ac y aceite en agua (Ac/Ag, sometidas al deterioro oxidativo por medio de la radiación ultravioleta A-visible (UVAVIS.En la emulsión de Ag/Ac (margarina, el aceite esencial de orégano presentó actividad antioxidante superior a la del cilantro y el romero, e incluso a la de la vitamina E, en concentraciones de 1, 10 y 20 g/kg. Se estableció además, que la acción antioxidante in vitro de los aceitesesenciales de orégano y cilantro aumentaba con su concentración en la margarina.Por último, el aceite esencial de orégano presentó una acción protectora más baja en la emulsión de Ac/Ag.

  7. EXTRACCIÓN Y CARACTERIZACIÓN DEL ACEITE CRUDO DE LA ALMENDRA DE DURAZNO Prunus pérsica

    Directory of Open Access Journals (Sweden)

    Peggy Londoño

    2012-01-01

    Full Text Available Se extrajo y purificó el aceite de la almendra de durazno con el propósito de recomendar su utilización desde el punto de vista químico y tecnológico. La purificación comprende el desgomado, la neutralización, en la cual se pone en contacto el aceite con solución de soda cáustica a 12,14 y 16º Bé. Seguidamente el blanqueado, donde el aceite neutralizado se trata con tierras blanqueantes en diferentes proporciones. El blanqueado se obtiene utilizando un porcentaje de tierra de 1,5 % el menor índice de peroxido – 2,03 meq O 2 kg -1 – y una acidez de 0,08 % como ácido oleico. Los ácidos grasos mayoritarios encontrados fueron oleico 77,9 % y linoleico 15,5 %. El aceite refinado es más estable que el aceite crudo y se puede recomendar su uso en la elaboración de diversos productos químicos previo a una evaluación toxicológica exhaustiva

  8. Specifics of phytomass combustion in small experimental device

    Science.gov (United States)

    Lenhard, Richard; Mičieta, Jozef; Jandačka, Jozef; Gavlas, Stanislav

    2015-05-01

    A wood pellet combustion carries out with high efficiency and comfort in modern pellet boilers. These facts help to increase the amount of installed pellet boilers in households. The combustion process quality depends besides the combustion conditions also on the fuel quality. The wood pellets, which don`t contain the bark and branches represent the highest quality. Because of growing pellet demand, an herbal biomass (phytomass), which is usually an agricultural by-product becomes economically attractive for pellet production. Although the phytomass has the net calorific value relatively slightly lower than the wood biomass, it is often significantly worse in view of the combustion process and an emission production. The combustion of phytomass pellets causes various difficulties in small heat sources, mainly due to a sintering of fuel residues. We want to avoid the ash sintering by a lowering of temperature in the combustion chamber below the ash sintering temperature of phytomass via the modification of a burner design. For research of the phytomass combustion process in the small boilers is constructed the experimental combustion device. There will investigate the impact of cooling intensity of the combustion chamber on the combustion process and emissions. Arising specific requirements from the measurement will be the basis for the design of the pellet burner and for the setting of operating parameters to the trouble-free phytomass combustion was guaranteed.

  9. Specifics of phytomass combustion in small experimental device

    Directory of Open Access Journals (Sweden)

    Lenhard Richard

    2015-01-01

    Full Text Available A wood pellet combustion carries out with high efficiency and comfort in modern pellet boilers. These facts help to increase the amount of installed pellet boilers in households. The combustion process quality depends besides the combustion conditions also on the fuel quality. The wood pellets, which don`t contain the bark and branches represent the highest quality. Because of growing pellet demand, an herbal biomass (phytomass, which is usually an agricultural by-product becomes economically attractive for pellet production. Although the phytomass has the net calorific value relatively slightly lower than the wood biomass, it is often significantly worse in view of the combustion process and an emission production. The combustion of phytomass pellets causes various difficulties in small heat sources, mainly due to a sintering of fuel residues. We want to avoid the ash sintering by a lowering of temperature in the combustion chamber below the ash sintering temperature of phytomass via the modification of a burner design. For research of the phytomass combustion process in the small boilers is constructed the experimental combustion device. There will investigate the impact of cooling intensity of the combustion chamber on the combustion process and emissions. Arising specific requirements from the measurement will be the basis for the design of the pellet burner and for the setting of operating parameters to the trouble-free phytomass combustion was guaranteed.

  10. Dioxines, furans and other pollutants emissions bond to the combustion of natural and additive woods

    International Nuclear Information System (INIS)

    Collet, S.

    2000-02-01

    This report deals especially on the dioxines and furans bond to the combustion of wood in industrial furnaces and domestic furnaces. It aims to define the environmental strategy which would allow the combustion of wood residues to produce energy. The first part recalls general aspects concerning the wood. The six other parts presents the wood resources and wastes, the additive used, the combustion and the different factors of combustion and finally the pollutants emissions. (A.L.B.)

  11. Composición Química y Actividad Antibacteriana del Aceite Esencial de Minthostachys mollis

    OpenAIRE

    Torrenegra-Alarcón, Miladys; Granados-Conde, Clemente; Durán-Lengua, Marlene; León-Méndez, Glicerio; Yáñez-Rueda, Xiomara; Martínez, César; Pájaro-Castro, Nerlis

    2016-01-01

    Se evaluó la composición química y la actividad antibacteriana del aceite esencial Minthostachys mollis cultivado en el departamento de Norte de Santander, Colombia.El aceite esencial fue obtenido por hidrodestilación convencional, a partir de las hojas; se determinó densidad relativa a 20°C, índice de refracción; solubilidad de los aceites esenciales en etanol (70% v/v) y rotación óptica. La composición química se evaluó mediante cromatografía de gases/espectrómetro de masa. La actividad se ...

  12. INFLUENCIA DE LA TEMPERATURA Y EL PORCENTAJE DEL CATALIZADOR EN LA ETANÓLISIS DEL ACEITE DE PALMA

    Directory of Open Access Journals (Sweden)

    Paulo César Narváez

    2008-03-01

    Full Text Available En este artículo se presenta la influencia de la temperatura y el porcentaje de catalizador sobre la etanólisis del aceite de palma, y los resultados se comparan con los obtenidos para la metanólisis del mismo aceite. Se realizaron ensayos a 60, 70 y 75 ºC, empleando como catalizador NaOH. Los porcentajes en peso de catalizadorcon respecto al aceite de palma fueron 0,20; 0,50 y 1,00. Los resultados muestran que incrementos en la temperaturay en el porcentaje de catalizador aumentan el rendimiento de la reacción. En comparación con la metanólisis, en la etanólisisse observó disminución en el rendimiento y en la selectividad.

  13. Particle Emissions from Biomass Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Szpila, Aneta; Bohgard, Mats [Lund Inst. of Technology (Sweden). Div. of Ergonomics and Aerosol Technology; Strand, Michael; Lillieblad, Lena; Sanati, Mehri [Vaexjoe Univ. (Sweden). Div. of Bioenergy Technology; Pagels, Joakim; Rissler, Jenny; Swietlicki, Erik; Gharibi, Arash [Lund Univ. (Sweden). Div. of Nuclear Physics

    2003-05-01

    We have shown that high concentrations of fine particles of the order of 2-7x10{sup -7} particles per cm{sup 3} are being formed in all the combustion units studied. There was a higher difference between the units in terms of particle mass concentrations. While the largest differences was found for gas-phase constituents (CO and THC) and polyaromatic hydrocarbons. In 5 out of 7 studied units, multi-cyclones were the only measure for flue-gas separation. The multicyclones had negligible effect on the particle number concentration and a small effect on the mass of particles smaller than 5 {mu}m. The separation efficiency was much higher for the electrostatic precipitators. The boiler load had a dramatic influence on the coarse mode concentration during combustion of forest residue. PM0.8-6 increased from below 5 mg/m{sup 3} to above 50 mg/m{sup 3} even at a moderate change in boiler load from medium to high. A similar but less pronounced trend was found during combustion of dry wood. PM0.8-PM6 increased from 12 to 23 mg/m{sup 3} when the load was changed from low to high. When increasing the load, the primary airflow taken through the grate is increased; this itself may lead to a higher potential of the air stream to carry coarse particles away from the combustion zone. Measurements with APS-instrument with higher time-resolution showed a corresponding increase in coarse mode number concentration with load. Additional factor influencing observed higher concentration of coarse mode during combustion of forest residues, could be relatively high ash content in this type of fuel (2.2 %) in comparison to dry wood (0.3 %) and pellets (0.5 %). With increasing load we also found a decrease in PM1 during combustion of forest residue. Whether this is caused by scavenging of volatilized material by the high coarse mode concentration or a result of a different amount of volatilized material available for formation of fine particles needs to be shown in future studies. The

  14. Combustion Research Facility

    Data.gov (United States)

    Federal Laboratory Consortium — For more than 30 years The Combustion Research Facility (CRF) has served as a national and international leader in combustion science and technology. The need for a...

  15. Alcohol combustion chemistry

    KAUST Repository

    Sarathy, Mani; Oß wald, Patrick; Hansen, Nils; Kohse-Hö inghaus, Katharina

    2014-01-01

    . While biofuel production and its use (especially ethanol and biodiesel) in internal combustion engines have been the focus of several recent reviews, a dedicated overview and summary of research on alcohol combustion chemistry is still lacking. Besides

  16. Application of preservatives for residual fuels

    International Nuclear Information System (INIS)

    Gorozpe y Munoz, Tomas

    2000-01-01

    Due to the high costs of the combust oils (fuel oil 6) used in generators of vapor and in other treatments, makes important consider the use of preservatives that improve the operation of the units from the operative point of view and of environmental control. The author enumerates several of the problems of corrosion, of efficiency in the combustion and of thermal efficiency; in a same way it enumerates several useful preservatives, to be used in residual fuel

  17. Evaluación nematicida del aceite esencial de Tagetes zypaquirensis en el manejo del nematodo Meloidogyne spp.

    Directory of Open Access Journals (Sweden)

    David Eduardo Álvarez

    2016-06-01

    Full Text Available El lulo (Solanum quitoense Lam. es un frutal andino de gran importancia económica en Colombia, sin embargo, las áreas sembradas y rendimientos han sufrido una evidente reducción debido al ataque de patógenos como el nematodo Meloidogyne spp., que ha ocasionado pérdidas de hasta 50%. En la naturaleza existen diferentes recursos vegetales con propiedades nematicidas, destacándose al género Tagetes. El objetivo de esta investigación fue evaluar la actividad nematicida del aceite esencial de Tagetes zypaquirensis sobre Meloidogyne spp. Bajo condiciones de invernadero se evaluaron cuatro concentraciones del aceite esencial (100, 200, 400, 800mg/kg de suelo las cuales fueron aplicadas a un suelo con juveniles de segundo estadio del nematodo +400 J2/100g. Además, se establecieron tres comparadores: un tratamiento sin aplicación de aceite esencial, un suelo sin nematodo y un suelo tratado con i.a carbofuran (33,2% bajo una dosis de 2cc/L. Para cada tratamiento, las variables a evaluar fueron: severidad, altura de planta, peso fresco y seco al aire, peso fresco radical, número de huevos del nematodo/100g raíz y número de J2/100g de suelo. Los componentes mayoritarios del aceite esencial de T. zypaquirensis fueron dihidrotagetona y E-tagetona con una proporción relativa de 42,2 y 22,9%, respectivamente. Los resultados indicaron, que la concentración 800mg/kg de aceite esencial presentó la misma acción nematicida que el suelo tratado con carbofuran al reducir las poblaciones de Meloidogyne spp. y presentar valores similares en las variables fitométricas. Se concluye que el aceite esencial T. zypaquirensis puede ser una alternativa para el manejo de la enfermedad del nudo radical.

  18. Perspectivas globales de utilización de grasas y aceites. Presente y futuro

    Directory of Open Access Journals (Sweden)

    Leysen, Ir. Rogar

    1996-10-01

    Full Text Available The paper shows current overview and the perspectives related to the production of oilseeds, fats and oils as well as the consumption of them. The study is based on the evolution of several variables such as changes in population, policies, incomes, prices, availability of natural resources (land for agriculture and environmental impact. With respect to technology, the work comments the possible influences of biotechnology transportation systems, milling, and some transformations for specific uses. Among the promising uses of vegetable oils the following are mentioned: utilization as biodiesel, adhesives, biodegradable plastics, printing inks, lubricating oils, hydraulic fluids or, even, new tendencies in the area of nutrition (foods with pharmacological effects.

    El trabajo comenta el estado actual y las perspectivas de futuro de la producción de semillas oleaginosas, aceites y grasas, así como el consumo de los mismos. Dicho estudio, se basa en la evolución de una serie de variables tales como los cambios de población, políticas, ventas, precios, disponibilidad de los recursos naturales (tierras para la producción agrícola y el impacto sobre el Medio Ambiente. En el aspecto tecnológico se hace especial mención sobre el impacto previsible de la biotecnología, transporte, molienda y posibles transformaciones para determinados usos. Entre las aplicaciones prometedoras de los aceites vegetales se mencionan el empleo como biodiesel, adhesivos, plásticos biodegradables, tintas de impresión, aceites lubricantes y líquidos hidráulicos e, incluso, nuevas tendencias en el campo de la alimentación (alimentos con algún papel de índole farmacológico.

  19. La familia Euphorbiaceae como fuente de aceites vegetales para la industria tecnoquímica

    Directory of Open Access Journals (Sweden)

    Correal Castellanos, E.

    1992-02-01

    Full Text Available The family Euphorbiaceae includes a huge number of species some of which provide important raw materials such as rubber, cassava, waxes and oils. In this study, the general botanical and chemical characteristics of this family are described firstly together with the chemical composition of their seed oils and a comparison with those of other families. Secondly, other chemical constituents of economic interest are reviewed and compared with the species already used for food, industry and medicine purposes. A further revision is included on some of its genus with potential interest and on current industrial oil crops such as Ridnus, Euphorbia, Aleurites, Sapium, Jatropha, etc. Finally, from an economic point of view, future prospects of some of these oils as raw materials for the chemical industry are given.La familia Euphorbiaceae contiene gran número de especies de las que se pueden obtener productos de interés económico como el caucho, la tapioca, ceras y aceites. En este trabajo se estudian en primer lugar las características botánicas y químicas de la familia y las peculiaridades de los aceites de sus semillas y se comparan con los de otras familias. En segundo lugar, se revisan otros compuestos químicos así como especies de interés económico utilizadas en alimentación, medicina o industria, incluyendo géneros con potencial interés y los actuales cultivos oleaginosos industriales como Ridnus, Euphorbia, Aleurites, Sapium, Jatropha, etc. Finalmente, desde un punto de vista de mercado, se apuntan las perspectivas de estos aceites como materias primas para la industria química.

  20. Maximal combustion temperature estimation

    International Nuclear Information System (INIS)

    Golodova, E; Shchepakina, E

    2006-01-01

    This work is concerned with the phenomenon of delayed loss of stability and the estimation of the maximal temperature of safe combustion. Using the qualitative theory of singular perturbations and canard techniques we determine the maximal temperature on the trajectories located in the transition region between the slow combustion regime and the explosive one. This approach is used to estimate the maximal temperature of safe combustion in multi-phase combustion models

  1. Metabolismo de carbohidratos en palmas de aceite (elaeis guineensis jacq.) afectadas por marchitez letal

    OpenAIRE

    Pèrez, Angela Patricia; Cayòn, Gerardo

    2010-01-01

    La enfermedad conocida como “marchitez letal” se presenta
    en plantaciones de la zona baja del río Upía, en palmas de siete
    años de sembradas. No se conoce el posible agente causal o
    factores que predisponen a las palmas a la enfermedad, y no se
    ha registrado hasta la fecha en otras zonas palmeras del país. Se
    analizó el metabolismo de carbohidratos en palmas de aceite
    con síntomas iniciales de la enfermedad, palmas sospechosas&...

  2. Enemigos naturales de Stenoma cecropia (Lepidoptera: Elachistidae) en palma de aceite, en el suroccidente de Colombia

    OpenAIRE

    SENDOYA-CORRALES, CARLOS ANDRÉS; BUSTILLO-PARDEY, ALEX ENRIQUE

    2016-01-01

    Stenoma cecropia infesta las nuevas siembras del híbrido interespecífico (Elaeis oleifera x E. guineensis) de palma de aceite en la zona de Tumaco (Nariño). Sus infestaciones afectan grandes extensiones de palma y causan defoliaciones de importancia económica. Por tal motivo, el objetivo de este trabajo fue determinar los factores bióticos y abióticos que afectan las poblaciones de la plaga a través de muestreos secuenciales quincenales, siguiendo un sistema móvil de desplazamiento 2 x 2, que...

  3. Diacilgliceroles en la evaluación de la calidad de aceite de oliva virgen

    Directory of Open Access Journals (Sweden)

    Catalano, M.

    1994-12-01

    Full Text Available Virgin olive oil samples were analyzed within one month after extraction and after one year; edible and lampante olive oil samples were analyzed before and after neutralization of free acids.
    In addition to the usual quality parameters, the amount and position isomers of diglycerides were equally assessed.
    It was found that extra virgin olive oils, even through analyzed after one year, still meet at least two of the following five requirements: a total diglycerides < 2.0%; b 1,2-diglycerides < 1.5%; c 1,3-diglycerides < 0,4%; d total diglycerides x 1,3-diglycerides < 1.0; e total diglycerides/1,3-diglycerides > 5.0.
    It is therefore suggested that for extra virgin oils to be defined, they should comply with at least two of the above parameters, in addition to the characters prescribed for by EC Regulations Nos. 2568/91 and 183/93.

    Se han analizado muestras de aceite de oliva virgen dentro del primer mes después de la extracción y después del primer año; también se han analizado muestras de aceite de oliva comestible y lampante antes y después de la neutralización de los ácidos libres.
    Además de los parámetros usuales de calidad se han evaluado igualmente los contenidos e isómeros de posición de los diglicéridos.
    Se encontró que los aceites de oliva extra vírgenes, incluso los analizados después del primer año, aún satisfacían al menos dos de los siguientes cinco requisitos: a diglicéridos totales < 2.0%; b 1,2-diglicéridos < 1.5%; c 1,3-diglicéridos < 0.4%; d diglicéridos totales x 1,3-diglicéridos < 1.0; e diglicéridos totales/1,3-diglicéridos > 5.0.
    Se sugiere por tanto que para ser definidos como aceites vírgenes extra, deben cumplir con al menos dos de los parámetros anteriores, además de con las características establecidas por las Regulaciones Números 2568/91 y 183/93 de la CE.

  4. Extracción de compuestos aromáticos con furfural en aceites lubricantes recuperados

    OpenAIRE

    Meléndez Hernández, Marianna Andrea

    2015-01-01

    Se presenta un estudio experimental y diseño conceptual con especificación de equipos y análisis económico de un proceso de extracción con furfural de compuestos aromáticos presentes en la base lubricante recuperada, para su decoloración y desodorización, después del proceso de regeneración de aceites usados en la empresa Biochemical Group -- Se realiza un diseño de experimentos factorial 32 para evaluar el proceso determinando la composición de hidrocarburos aromáticos en el extracto y refin...

  5. Extraccion de aceite de coco a partir de la copra por medio de disolventes quimicos

    OpenAIRE

    J. Rosario Rivera Hernández; Juana María Lomelí Soto; Lorena Román Salinas; Francisco Vera Figueroa

    2001-01-01

    Acetato de Etilo, alcohol Isopropílico, Hexano, Tetracloruro de carbono y xileno, fueron usados como disolventes para extraer de la copra aceite de coco. Se aplicaron dos procedimientos de extracción sólido-líquido a la temperatura de ebullición de los disolventes, así mismo se efectuaron tres corridas de extracción a tiempos de 1.0, 1.5 y 2.0 hrs. los resultados de las extracciones aparecen en las tablas 1 y 2.

  6. TECNOLOGÍAS DE TRATAMIENTO PARA LA TIERRA FULLER CONTAMINADA CON ACEITE DIELÉCTRICO

    Directory of Open Access Journals (Sweden)

    Óscar Darío Beltrán Pérez

    Full Text Available Desde hace algunos años en Colombia se vienen implementando convenios y normas para el adecuado manejo y disposición final de los residuos peligrosos, debido a que la cantidad generada cada vez va en aumento y al impacto adverso que estos residuos presentan en el ser humano y el medio ambiente. La tierra Fuller es un material inorgánico adsorbente (mineral de aluminosilicatos principalmente, utilizado en la industria eléctrica para la regeneración del aceite dieléctrico, un derivado del petróleo empleado como aislante eléctrico y térmico en los transformadores de potencia. Después del proceso de regeneración del aceite, el contenido de hidrocarburos del tipo poliaromáticos (o los PAH por sus siglas en inglés que presenta la tierra Fuller la convierten en un residuo peligroso que requiere de un adecuado tratamiento, para que reduzca su contaminación y permita su reutilización o segura disposición final en un relleno sanitario. Por esto, en este artículo se revisan las tecnologías disponibles para el tratamiento de este tipo de residuo peligroso (tierra Fuller contaminada con aceite dieléctrico, dividiendo los tratamientos en dos corrientes, las tecnologías fisicoquímicas y las biológicas, explorando las alternativas más apropiadas y eficientes para su tratamiento. La escasa información acerca de los tratamientos existentes para la tierra Fuller contaminada con aceite dieléctrico han orientado la revisión en términos de las tecnologías implementadas en suelos contaminados con hidrocarburos siendo válida la analogía debido a las similares características físicas que presenta la tierra Fuller con respecto a un suelo de bajo contenido de carbono.

  7. Theoretical Adiabatic Temperature and Chemical Composition of Sodium Combustion Flame

    International Nuclear Information System (INIS)

    Okano, Yasushi; Yamaguchi, Akira

    2003-01-01

    Sodium fire safety analysis requires fundamental combustion properties, e.g., heat of combustion, flame temperature, and composition. We developed the GENESYS code for a theoretical investigation of sodium combustion flame.Our principle conclusions on sodium combustion under atmospheric air conditions are (a) the maximum theoretical flame temperature is 1950 K, and it is not affected by the presence of moisture; the uppermost limiting factor is the chemical instability of the condensed sodium-oxide products under high temperature; (b) the main combustion product is liquid Na 2 O in dry air condition and liquid Na 2 O with gaseous NaOH in moist air; and (c) the chemical equilibrium prediction of the residual gaseous reactants in the flame is indispensable for sodium combustion modeling

  8. Evolución de la calidad de aceites de fritura utilizando Fourier Transform Near Infrared Spectroscopy

    OpenAIRE

    Muñoz Marchal, Estrella

    2018-01-01

    Premio extraordinario de Trabajo Fin de Máster curso 2015-2016. Ingeniería y Gestión de la Cadena Agroalimentaria Durante el proceso de fritura, todos los aceites, sin importar la fuente de procedencia, presentan cambios nutricionales y cualitativos, incluso llegando a generar elementos tóxicos. Se han desarrollado un gran número de procedimientos analíticos para evaluar los cambios producidos en el aceite de fritura con el fin de determinar cuándo éste debe ser desechado, pero...

  9. EFECTO ANTIMICROBIANO DEL ACEITE ESENCIAL DE Salvia officinalis L. SOBRE MICROORGANISMOS PÁTOGENOS TRANSMITIDOS POR ALIMENTOS

    OpenAIRE

    López-De Ávila, Lina M.; Castaño-Peláez, Hader I.; Mejía-Gómez, Carlos E.

    2013-01-01

    El objetivo de este estudio fue evaluar la actividad antimicrobiana del aceite esencial de Salvia officinalis L. sobre microorganismos transmitidos por alimentos con alto potencial patogénico en humanos. Para determinar su efectividad como alternativa en la conservación de alimentos se comparó con la actividad antimicrobiana de compuestos químicos utilizados ampliamente en la industria de alimentos. El aceite esencial de S. officinalis demostró un amplio espectro de inhibición microbiana sobr...

  10. Influencia del aceite esencial de ajo sobre la fermentación ruminal y la diversidad bacteriana en fermentadores Rusitec

    OpenAIRE

    García Rodríguez, J.; Carro Travieso, Maria Dolores; Saro, C.; Mateos, I.; Tejido, M. L.; Ranilla, M. J.

    2017-01-01

    En los últimos años se han estudiado múltiples estrategias alternativas al uso de antibióticos promotores del crecimiento como aditivos en la alimentación de los rumiantes. Entre estas estrategias se encuentra el uso de los compuestos bioactivos de las plantas, como son los aceites esenciales, capaces de modificar la fermentación ruminal. El aceite esencial de ajo ha mostrado resultados prometedores en anteriores estudios in vitro de corta duración (Busquet et al, 2005; Mateos ...

  11. Efecto citoprotector y antisecretor del aceite de Copaifera officinalis en lesiones gástricas inducidas en ratas

    Directory of Open Access Journals (Sweden)

    Jorge Arroyo

    2009-06-01

    Full Text Available Objetivos: Demostrar el efecto gastroprotector del aceite de Copaifera officinalis usando indometacina y ligadura de píloro en ratas. Diseño: Estudio preclínico. Lugar: Facultades de Medicina, de Farmacia y Bioquímica. Universidad Nacional Mayor de San Marcos, Lima, Perú. Material biológico: Ratas y aceite de copaiba. Intervenciones: Se colectó el aceite de copaiba en Ucayali, Pucallpa. La citoproteccción fue evaluada con indometacina, considerando un grupo control normal, indometacina, grupos de aceite de copaiba y omeprazol. Las lesiones de la mucosa gástrica fueron calificadas como las compatibles con necrosis local (tejido no viable, hiperemia, enrojecimiento presente y hemorragia, empleando la escala de puntaje observacional; y la úlcera, según la escala de Macallister modificado. El ensayo de antisecreción fue realizado por el modelo de ligadura del píloro, en el que 24 ratas albinas fueron divididas al azar en 3 grupos; un control, otro de aceite de copaiba 40mg/kg y un tercero de omeprazol 10 mg/kg. Después de 4 horas de ligazón, fueron sacrificados, extrayéndose los estómagos; con mucho cuidado se midió el volumen y se determinó el pH de la secreción gástrica, por potenciometría. Se realizó evaluación histopatológica según Devi. Principales medidas de resultados: Lesiones ulcerosas. Resultados: Los resultados indicaron 100% de efecto citoprotector con el aceite de copaiba y de 97,8% para el omeprazol (p<0,0001, ratificado con los hallazgos histopatológicos; la disminución del volumen de secreción fue 79,4% para omeprazol y 42,8% para el aceite de copaiba (p<0,001, con incremento del pH. Conclusiones: En condiciones experimentales, el aceite de copaiba fue efectivo como agente gastroprotector en ratas con inducción de úlcera gástrica.

  12. Modeling the internal combustion engine

    Science.gov (United States)

    Zeleznik, F. J.; Mcbride, B. J.

    1985-01-01

    A flexible and computationally economical model of the internal combustion engine was developed for use on large digital computer systems. It is based on a system of ordinary differential equations for cylinder-averaged properties. The computer program is capable of multicycle calculations, with some parameters varying from cycle to cycle, and has restart capabilities. It can accommodate a broad spectrum of reactants, permits changes in physical properties, and offers a wide selection of alternative modeling functions without any reprogramming. It readily adapts to the amount of information available in a particular case because the model is in fact a hierarchy of five models. The models range from a simple model requiring only thermodynamic properties to a complex model demanding full combustion kinetics, transport properties, and poppet valve flow characteristics. Among its many features the model includes heat transfer, valve timing, supercharging, motoring, finite burning rates, cycle-to-cycle variations in air-fuel ratio, humid air, residual and recirculated exhaust gas, and full combustion kinetics.

  13. Residual stresses

    International Nuclear Information System (INIS)

    Sahotra, I.M.

    2006-01-01

    The principal effect of unloading a material strained into the plastic range is to create a permanent set (plastic deformation), which if restricted somehow, gives rise to a system of self-balancing within the same member or reaction balanced by other members of the structure., known as residual stresses. These stresses stay there as locked-in stresses, in the body or a part of it in the absence of any external loading. Residual stresses are induced during hot-rolling and welding differential cooling, cold-forming and extruding: cold straightening and spot heating, fabrication and forced fitting of components constraining the structure to a particular geometry. The areas which cool more quickly develop residual compressive stresses, while the slower cooling areas develop residual tensile stresses, and a self-balancing or reaction balanced system of residual stresses is formed. The phenomenon of residual stresses is the most challenging in its application in surface modification techniques determining endurance mechanism against fracture and fatigue failures. This paper discusses the mechanism of residual stresses, that how the residual stresses are fanned and what their behavior is under the action of external forces. Such as in the case of a circular bar under limit torque, rectangular beam under limt moment, reclaiming of shafts welds and peening etc. (author)

  14. Comparative study on systems of residual water treatment in the process industry by evaporation, using fossils fuels or solar energy; Estudio comparativo sobre sistemas de tratamiento de aguas residuales de la industria de procesamiento por evaporacion, utilizando combustibles fosiles o energia solar

    Energy Technology Data Exchange (ETDEWEB)

    Landgrave Romero, Julio; Canseco Contreras, Jose [Facultad de Quimica, UNAM (Mexico)

    1996-07-01

    The residual water treatment of the process industry, nowadays is an imminent necessity in our country. In the present study two different forms are considered to concentrate residual waters: multiple effect evaporation and solar evaporation. The use of solar evaporation lagoons is a good possibility to conserving energy by means of the diminution of fossil fuel consumption. The design basis of the evaporation systems via multiple effect, as well as solar evaporation, the results of the respective sizing and the estimation of the corresponding costs are presented. A practical case is described on the cooking of cotton linters (flock) [Spanish] El tratamiento de aguas residuales de la industria de proceso, hoy en dia es una necesidad inminente en nuestro pais. En el presente trabajo se consideran dos formas distintas para concentrar las aguas residuales: evaporacion de multiple efecto y evaporacion solar. El empleo de lagunas de evaporacion solar es una buena posibilidad para conseguir el ahorro de energia mediante disminucion del consumo de combustibles fosiles. Se presentan las bases de diseno de los sistemas de evaporacion via multiple efecto, asi como solar, los resultados del dimensionamiento respectivo y la estimacion de los costos correspondientes. Se describe un caso practico sobre el cocido de linters de algodon (borra)

  15. Uncertainties in hydrogen combustion

    International Nuclear Information System (INIS)

    Stamps, D.W.; Wong, C.C.; Nelson, L.S.

    1988-01-01

    Three important areas of hydrogen combustion with uncertainties are identified: high-temperature combustion, flame acceleration and deflagration-to-detonation transition, and aerosol resuspension during hydrogen combustion. The uncertainties associated with high-temperature combustion may affect at least three different accident scenarios: the in-cavity oxidation of combustible gases produced by core-concrete interactions, the direct containment heating hydrogen problem, and the possibility of local detonations. How these uncertainties may affect the sequence of various accident scenarios is discussed and recommendations are made to reduce these uncertainties. 40 references

  16. New class of combustion processes

    International Nuclear Information System (INIS)

    Merzhanov, A.G.; Borovinskaya, I.P.

    1975-01-01

    A short review is given of the results of work carried out since 1967 on studying the combustion processes caused by the interaction of chemical elements in the condensed phase and leading to the formation of refractory compounds. New phenomena and processes are described which are revealed when investigating the combustion of the systems of this class, viz solid-phase combustion, fast combustion in the condensed phase, filtering combustion, combustion in liquid nitrogen, spinning combustion, self-oscillating combustion, and repeated combustion. A new direction in employment of combustion processes is discussed, viz. a self-propagating high-temperature synthesis of refractory nitrides, carbides, borides, silicides and other compounds

  17. Potencial contaminante del mar por aguas residuales de las industrias de harinas y aceites de pescado

    Directory of Open Access Journals (Sweden)

    Mendiola, Santiago

    1998-02-01

    Full Text Available . In this study we addressed the polluting potential that constitutes the disposal of wastewater from the fish meal and oil Industries Into the sea. With this aim we have analysed some phisico-chemical and bacteriologic aspects of the effluents of these industries, including: weight percentage of organic matter, chemical oxygen load, fatty acids saturation, and presence of Salmonellas. The results suggest a low polluting potential for these effluents, although the acid pH and the high rate of saturation found In fatty acids of oil fishes could imply a certain toxicity for the marine environment.

    En este trabajo se evalúa el potencial contaminante que representa el vertido al mar de los desechos procedentes de las industrias de harinas y aceites de pescado. Para ello se han analizado algunos aspectos de la composición físico-química y bacteriológica de los efluentes residuales de estas industrias, incluyendo entre otros: porcentaje en peso de materia orgánica, demanda química de oxígeno, saturación de ácidos grasos y presencia de Salmonellas. Los resultados muestran en general un bajo potencial contaminante de estas aguas residuales, aunque su pH ácido y el alto grado de saturación encontrado en los ácidos grasos de los aceites de pescado podrían conllevar una cierta toxicidad para el medio marino.

  18. Aceites Esenciales: Una opción quimioterapéutica en Periodoncia

    Directory of Open Access Journals (Sweden)

    Natalia Asquino

    Full Text Available Las enfermedades periodontales representan un conjunto de patologías que afectan los tejidos de soporte dentario. La remoción del biofilm diaria y efectiva es suficiente para prevenirlas. La dificultad de los individuos en desarrollar hábitos de higiene oral adecuados valiéndose solamente de elementos mecánicos llevó al desarrollo de coadyuvantes químicos con el objetivo de maximizar el control del biofilm por el paciente. Los aceites esenciales son eficaces y superiores en el control de la placa supragingival y la inflamación en comparación con placebo y cloruro de cetilpiridinio. Sin embargo, fueron similares en el control de la inflamación e inferiores en el control de placa en comparación con la clorhexidina, generando menos efectos adversos. La evidencia sugiere que para el cuidado oral a corto plazo la clorhexidina es la primera opción y que los aceites esenciales muestran utilidad al ser indicados a largo plazo cuando el cuidado oral antiinflamatorio sea beneficioso

  19. OBTENCIÓN DE FRACCIONES ENRIQUECIDAS DURANTE LA EXTRACCIÓN DE ACEITES ESENCIALES CRUDOS

    Directory of Open Access Journals (Sweden)

    María S. Guala

    2012-01-01

    Full Text Available La destilación por arrastre con vapor es uno de los métodos más utilizados para la obtención de aceite esencial crudo (AEC. Muchas aplicaciones requieren fracciones de AEC, enriquecidas en un componente o grupo de ellos, para lo cual se utiliza destilación al vacío. En este trabajo se propone realizar un fraccionamiento del aceite esencial crudo (AEC durante el proceso de extracción por destilación con arrastre de vapor, para lo cual se colectaron distintos cortes, en lugar de una única mezcla final que es la metodología tradicionalmente utilizada. Las experiencias se llevaron a cabo utilizando frutos, hojas y tallos de aguaribay (Schinus molle L.. La composición de las distintas muestras obtenidas se determinó por cromatografía gaseosa acoplada a espectroscopía de masas. Los resultados muestran diferentes componentes (y concentraciones para los diferentes cortes, lo que indica que se puede lograr una apreciable separación utilizando esta metodología.

  20. Residual stresses

    International Nuclear Information System (INIS)

    Macherauch, E.

    1978-01-01

    Residual stresses are stresses which exist in a material without the influence of external powers and moments. They come into existence when the volume of a material constantly changes its form as a consequence of mechanical, thermal, and/or chemical processes and is hindered by neighbouring volumes. Bodies with residual stress are in mechanical balance. These residual stresses can be manifested by means of all mechanical interventions disturbing this balance. Acoustical, optical, radiological, and magnetical methods involving material changes caused by residual stress can also serve for determining residual stress. Residual stresses have an ambivalent character. In technical practice, they are feared and liked at the same time. They cause trouble because they can be the cause for unexpected behaviour of construction elements. They are feared since they can cause failure, in the worst case with catastrophical consequences. They are appreciated, on the other hand, because, in many cases, they can contribute to improvements of the material behaviour under certain circumstances. But they are especially liked for their giving convenient and (this is most important) mostly uncontrollable explanations. For only in very few cases we have enough knowledge and possibilities for the objective evaluation of residual stresses. (orig.) [de

  1. Estudio Teórico de la Influencia del Uso de Mezclas de Biodiesel de Aceite de Palma con JET a-1 en Motores a Reacción

    Directory of Open Access Journals (Sweden)

    Luisa Fernanda Mónico Muñoz

    2017-02-01

    Full Text Available Contexto: al igual que en muchas otras, en la actualidad, la industria aeronáutica se ha visto obligada a implementar métodos para mitigar el daño producido al medio ambiente por la emisión de gases contaminantes, y de esta manera hacerle frente a la problemática del calentamiento global. En este panorama, la investigación sobre la utilización de combustibles alternativos es de suma relevancia, en particular el estudio del rendimiento de motores al usar mezclas de Biodiesel Colombiano a base de aceite de palma con Jet A1.  Método: como punto de partida, se realiza una revisión al estado del arte para la selección del motor a estudiar y los combustibles alternativos a utilizar. Paralelamente, se seleccionó el biodiesel colombiano a base de aceite de palma, ya que ha demostrado tener un buen comportamiento como combustible al ser mezclado en porcentajes de 10% ,20% y 50%. A cada una de las mezclas realizadas se les hicieron pruebas en laboratorio para conocer su valor de viscosidad, densidad y poder calorífico. Para la realización de los análisis, se desarrolló un programa sobre una hoja de cálculo que contempla Propiedades físicas de las mezclas y parámetros del motor, así como emisiones de óxidos nitrosos (NOx, atomización y combustión producida por el uso de las mezclas. Los resultados se contrastaron contra el software de simulación Gas turbine. Resultados: se escogió el CFM 56-5B como motor apropiado para realizar el estudio, debido a que en la actualidad es el más empleado en la industria aeronáutica colombiana.  Por otra parte, ninguna de las mezclas de combustible alternativo genera el mismo rendimiento del motor al emplear Jet A1. Las mezclas E10 y E20 tienen un comportamiento similar, con la novedad de generar menor cantidad de emisiones de NOx y mejorar la atomización del combustible. Conclusiones: al comparar el rendimiento del motor al usar combustible convencional y al emplear las mezclas de Biodiesel

  2. Co-combustion of waste materials using fluidized bed technology

    Energy Technology Data Exchange (ETDEWEB)

    M. Lopes; I. Gulyurtlu; P. Abelha; T. Crujeira; D. Boavida; I. Cabrita [INETI-DEECA, Lisbon (Portugal)

    2004-07-01

    There is growing interest in using renewable fuels in order to sustain the CO{sub 2} accumulation. Several waste materials can be used as coal substitutes as long as they contain significant combustible matter, as for example MSW and sewage sludge. Besides the outcome of the energetic valorization of such materials, combustion must be regarded as a pre-treatment process, contributing to the safe management of wastes. Landfilling is an expensive management option and requires a previous destruction of the organic matter present in residues, since its degradation generates greenhouse gases and produces acidic organic leachates. Fluidized bed combustion is a promising technology for the use of mixtures of coal and combustible wastes. This paper presents INETI's experience in the co-combustion of coal with this kind of residues performed in a pilot fluidized bed. Both the RDF (from MSW and sewage sludge) and sewage sludge combustion problems were addressed, relating the gaseous emissions, the behaviour of metals and the leachability of ashes and a comparison was made between co-combustion and mono-combustion in order to verify the influence of the utilization of coal. 9 refs., 1 fig., 3 tabs.

  3. Combustion modeling in internal combustion engines

    Science.gov (United States)

    Zeleznik, F. J.

    1976-01-01

    The fundamental assumptions of the Blizard and Keck combustion model for internal combustion engines are examined and a generalization of that model is derived. The most significant feature of the model is that it permits the occurrence of unburned hydrocarbons in the thermodynamic-kinetic modeling of exhaust gases. The general formulas are evaluated in two specific cases that are likely to be significant in the applications of the model.

  4. Actividad inhibitoria del aceite esencial de Lippia origanoides H.B.K sobre el crecimiento de Phytophthora infestans

    Directory of Open Access Journals (Sweden)

    óscar Arango Bedoya

    2015-04-01

    Full Text Available Phytophthora infestans (Mont. de Bary es el fitopatógeno más perjudicial de la papa (Solanum tuberosum al causar la enfermedad conocida como ‘gota o tizón tardío’. El objetivo de este trabajo fue evaluar la actividad in vitro del aceite esencial obtenido de una especie de orégano silvestre (Lippia origanoides H.B.K. sobre Phytophthora infestans. Para el efecto se evaluaron diferentes concentraciones de este aceite esencial (10, 50, 100, 150, 200, 250 µg/ml y de un fungicida comercial usado como testigo. La actividad antifúngica se determinó con base en la evaluación del crecimiento del micelio mediante el método de dilución en agar tomate. A partir de una concentración de aceite de 150 µg/ml se inhibió completamente el crecimiento del patógeno, por lo que ésta fue considerada como la concentración letal. Este estudio demostró que el aceite esencial de orégano silvestre del Alto Patía, Colombia, es un potencial agente antifúngico que podría ser usado en sistemas de control integrado de P. infestans.

  5. Aceites de oliva vírgenes y refinados: Diferencias en componentes menores glicerídicos

    Directory of Open Access Journals (Sweden)

    Pérez-Camino, M. C.

    1993-04-01

    Full Text Available This paper defines the main differences in glyceridic minor compounds between virgin and refined olive oils. Modifications during the steps of the refining process are studied and compared with differences found in two series of virgin and refined oils and those during storage. The results demonstrate that the absence of polymerized compounds is the most useful parameter for the characterization of virgin oils while the presence of dimeric triglycerides and a high ratio diglycerides/fatty acids are those for refined oils.

    En el presente trabajo se definen las principales diferencias en componentes menores glicerídicos entre aceites de oliva vírgenes y refinados. Para ello, se estudian las modificaciones que tienen lugar durante las distintas etapas del proceso de refinación, se comprueban las diferencias encontradas en dos series de aceites vírgenes y refinados y, finalmente, se analizan las modificaciones originadas durante el almacenamiento. Los resultados demuestran que la ausencia de compuestos de polimerización es de gran valor para la caracterización de los aceites de oliva vírgenes, mientras que, la presencia de dímeros de triglicéridos y la elevada relación diglicéridos/ácidos grasos son las características principales de los aceites refinados.

  6. Incidencia de la carga inicial de pesticidas en fruta sobre los niveles residuales en aceites esenciales cítricos

    Directory of Open Access Journals (Sweden)

    María I Montti

    2013-01-01

    Full Text Available En Argentina, la producción cítrica es muy importante. Para el control de enfermedades y plagas en las quintas y empaques son utilizados diferentes pesticidas. Los objetivos de este estudio fueron: optimizar diferentes metodologías analíticas para la determi- nación de residuos de pesticidas en fruta y aceite esencial, y determinar el efecto de la carga inicial sobre los aceites esenciales obtenidos durante el proceso industrial. La calibración se llevó a cabo con matriz adicionada debido al efecto matriz. Los mé- todos propuestos fueron selectivos, precisos, exactos y sensibles. La concentración de residuos encontrados en fruta fresca varió dependiendo del lote y pesticida. La persistencia en fruta postlavada, aceite pulido y descerado fue distinta para cada analito. Se observó una ligera reducción de los residuos en el aceite descerado debido probablemente a la partición de los mismos en la fase cerosa. Los resultados muestran que la carga inicial en la fruta es significante.

  7. Efecto sinérgico del aceite esencial de Origanum vulgare a la Gentamicina en cultivos de Escherichia coli.

    Directory of Open Access Journals (Sweden)

    Luis Chávez Torres

    2008-01-01

    Full Text Available Objetivo: El presente trabajo tuvo como propósito determinar el efecto sinérgico antibacteriano entre el aceite esencial de Origanum vulgare y la Gentamicina en aislados de Escherichia coli. Diseño: Estudio experimental Lugar: Centro Latinoamericano de Enseñanza e Investigación en Bacteriología Alimentaria (CLEIBA Participantes: Placas Petri conteniendo E. Coli ATCC 25922, aceite esencial de orégano y Gentamicina. Intervenciones: Se aplicó el método de Kirby Bauer (discos de difusión en 20 placas Petri. Se aisló la cepa Escherichia coli ATCC 25922. El grupo Experimental fue tratado con discos de papel filtro, embebidos con Gentamicina y aceite esencial de orégano al 75%; mientras que el grupo Control, con discos de Gentamicina sola. Se realizó la medición de los halos y se registraron los datos. Principales medidas de resultados: Se evaluó el diámetro de los halos de inhibición Resultados: Los halos de inhibición del grupo Experimental resultaron 22,375 mm., mayores que los del grupo Control (20,75 mm. La prueba T determinó que la diferencia era estadísticamente significativa, p = 0,001 (p < 0,05. Conclusiones: Existe un efecto sinérgico antibacteriano in vitro entre el aceite esencial de Origanum vulgare y la gentamicina en E. coli.

  8. EFECTO SINÉRGICO DEL ACEITE ESENCIAL DE Origanum vulgare A LA GENTAMICINA EN CULTIVOS DE Escherichia coli.

    Directory of Open Access Journals (Sweden)

    Luis Chávez Torres

    2012-02-01

    Full Text Available Objetivo: El presente trabajo tuvo como propósito determinar el efecto sinérgico antibacteriano entre el aceite esencial de Origanum vulgare y la Gentamicina en aislados de Escherichia coli. Diseño: Estudio experimental Lugar: Centro Latinoamericano de Enseñanza e Investigación en Bacteriología Alimentaria (CLEIBA Participantes: Placas Petri conteniendo E. Coli ATCC 25922, aceite esencial de orégano y Gentamicina. Intervenciones: Se aplicó el método de Kirby Bauer (discos de difusión en 20 placas Petri. Se aisló la cepa Escherichia coli ATCC 25922. El grupo Experimental fue tratado con discos de papel filtro, embebidos con Gentamicina y aceite esencial de orégano al 75%; mientras que el grupo Control, con discos de Gentamicina sola. Se realizó la medición de los halos y se registraron los datos. Principales medidas de resultados: Se evaluó el diámetro de los halos de inhibición Resultados: Los halos de inhibición del grupo Experimental resultaron 22,375 mm., mayores que los del grupo Control (20,75 mm. La prueba T determinó que la diferencia era estadísticamente significativa, p = 0,001 (p < 0,05. Conclusiones: Existe un efecto sinérgico antibacteriano in vitro entre el aceite esencial de Origanum vulgare y la gentamicina en E. coli.

  9. Boiler using combustible fluid

    Science.gov (United States)

    Baumgartner, H.; Meier, J.G.

    1974-07-03

    A fluid fuel boiler is described comprising a combustion chamber, a cover on the combustion chamber having an opening for introducing a combustion-supporting gaseous fluid through said openings, means to impart rotation to the gaseous fluid about an axis of the combustion chamber, a burner for introducing a fluid fuel into the chamber mixed with the gaseous fluid for combustion thereof, the cover having a generally frustro-conical configuration diverging from the opening toward the interior of the chamber at an angle of between 15/sup 0/ and 55/sup 0/; means defining said combustion chamber having means defining a plurality of axial hot gas flow paths from a downstream portion of the combustion chamber to flow hot gases into an upstream portion of the combustion chamber, and means for diverting some of the hot gas flow along paths in a direction circumferentially of the combustion chamber, with the latter paths being immersed in the water flow path thereby to improve heat transfer and terminating in a gas outlet, the combustion chamber comprising at least one modular element, joined axially to the frustro-conical cover and coaxial therewith. The modular element comprises an inner ring and means of defining the circumferential, radial, and spiral flow paths of the hot gases.

  10. Estrategia ambiental en el manejo de efluentes en la extracción de aceite de palma

    Directory of Open Access Journals (Sweden)

    María Bonomie

    2012-09-01

    Full Text Available En el proceso de extracción de aceite de palma, se consideran alternativas de separación de los residuos sólidos y líquidos para el aprovechamiento (si es posible total del efluente. Estos residuos sólidos de naturaleza orgánica, y las descargas líquidas, suelen considerarse de bajo impacto en comparación con otros procesos productivos de algunos sectores industriales. En este sentido, la presente investigación tiene como propósito analizar el manejo de los efluentes en el proceso de extracción de aceite de palma o aceite rojo. Asimismo, se presenta la estrategia ambiental en este tipo de proceso utilizando la producción más limpia. La investigación es de tipo analítica, no experimental de campo; la población se delimitó a las empresas del sector de palma aceitera que desarrolla el proceso de extracción de aceite. Se realizaron varias visitas y entrevistas al personal de estas empresas; siendo necesario aclarar que para efectos de esta investigación, solamente se considera la producción de aceite rojo, en virtud de que del proceso de producción se obtienen dos sub productos, aceite de palmiste y harina de palmiste. Los resultados, indican que existen efluentes en las diferentes etapas del proceso de extracción de aceite, los cuales reciben un tratamiento especial, por lo que requieren de áreas que desempeñan actividades de apoyo, tales como: control de calidad, mantenimiento y generación de energía, las cuales intervienen en la generación y tratamiento de los efluentes. Se concluye que las empresas que utilizan este tipo de proceso productivo, emplean estrategias innovadoras para disminuir el impacto ambiental, en aras de mejorar el desempeño ambiental en este tipo de organización.

  11. Efecto de los aceites y semillas en dietas para rumiantes sobre el perfil de ácidos grasos de la leche. Revisión

    OpenAIRE

    Andrés L. Martínez Marín; Manuel Pérez Hernández; Luis M. Pérez Alba; Domingo Carrión Pardo; Gustavo Gómez Castro; Ana I. Garzón Sígler

    2013-01-01

    Este trabajo presenta una revisión del efecto de la adición de aceites y semillas ricos en ácidos grasos insaturados, a la dieta de las hembras rumiantes, sobre el contenido de ácidos grasos de la grasa láctea. Cuando se incluyen aceites y semillas en la dieta, los cambios del perfil de ácidos grasos de la leche ocurren en el mismo sentido en vacas, ovejas y cabras. Algunos de los efectos observados son comunes a todos los aceites y semillas con independencia del ácido graso mayoritario que a...

  12. Cinética de la reacción de transesterificación del aceite de higuerilla en la obtención de biodiesel

    OpenAIRE

    Loaiza Romero, Francia Elena

    2003-01-01

    Se realizó un estudio de la cinética de la transesterificación del aceite de higuerilla con metanol e hidróxido de sodio como catalizador para la producción del metil éster de este aceite, Metil Ricinoleato. Se analizaron las posibles reacciones ocurridas mediante un mecanismo de reacción de transesterificación de un aceite vegetal con un alcohol utilizando un catalizador básico para obtener una expresión de la velocidad de reacción. Se ensayaron dos columnas cromatográficas disponibles para ...

  13. Efecto insecticida de los aceites esenciales de algunas lamiáceas sobre Tecia solanivora Povolny en condiciones de laboratorio

    Directory of Open Access Journals (Sweden)

    Ramìrez julian Ernesto

    2010-08-01

    Full Text Available La papa, el producto agrícola más importante en la economía de
    los andes colombianos, tiene en la polilla guatemalteca (Tecia
    solanivora Povolny su principal plaga, cuyo control se basa en
    el uso intensivo de plaguicidas. Una alternativa potencial a la
    aplicación de estos insumos es el uso de productos vegetales.
    En condiciones controladas, el presente trabajo evaluó el efecto
    de los aceites esenciales de Ocimum basilicum, O. majorana,
    M. piperita, O. vulgare, P. cablin, R. officinalis, S. officinalis y
    T. vulgaris sobre los huevos, larvas y adultos de T. solanivora
    al ser aplicados directamente sobre los tubérculos, y sobre la
    superficie del suelo. No se encontró ningún efecto de los tratamientos
    sobre el desarrollo larval ni sobre la longevidad de
    los adultos. En las dos modalidades de aplicación estudiadas,
    los aceites de P. cablin y T. vulgaris en una concentración del
    0,25% produjeron una reducción significativa en la viabilidad
    de los huevos. Al aumentar la humedad del suelo y el volumen
    de aplicación de los aceites, los aceites de O. basilicum, O.
    majorana, M. piperita, R. officinalis también tuvieron acción
    ovicida. Estos resultados son evidencia del potencial de estos
    aceites como controladores de Tecia solanivora.

  14. Ácidos grasos y parámetros de calidad del aceite de semilla de uva silvestre (Vitis spp.

    Directory of Open Access Journals (Sweden)

    O. Franco-Mora

    2015-01-01

    Full Text Available México es centro de origen de varias especies de Vitis. La gran mayoría de ellas no son empleadas en la agricultura e industrias derivadas. Como parte de la exploración de su potencial agroindustrial se identificó y cuantificó a los ácidos grasos del aceite de semilla de vid silvestre (Vitis spp. de frutos de Temascaltepec, México y de la accesión E-201, cultivada en Zumpahuacán, México. El contenido promedio de aceite en la semilla fue de 16,7%, encontrando ácido linoleico (71,5%, oleico (17,2%, palmítico (6,6% y esteárico (4,3%. En el aceite obtenido en vides de Temascaltepec se determinó índice de yodo (57,9 g/100 g, índice de saponificación (170,7 mg/g e índice de peroxidos (30 mEq/kg, valores relacionados posiblemente al contenido de ácidos grasos insaturados. Sin embargo, ese mismo grado de insaturación no concordó con el punto de humeo observado (211 °C, lo cual posiblemente está relacionado con el contenido de ácidos palmítico y esteárico. El aceite de semilla de vid silvestre cumple parcialmente con los estándares establecidos para el aceite de semilla de V. vinifera, lo cual implica su potencial culinario, agroindustrial y cosmetológico.

  15. Estabilidad oxidativa y estimación de la vida útil del aceite de sacha inchi (Plukenetia volubilis L.

    Directory of Open Access Journals (Sweden)

    Gilbert Rodríguez

    2015-01-01

    Full Text Available El aceite de sacha inchi es rico en ácidos grasos poli-insaturados que podrían oxidarse, limitando su vida útil. El método Rancimat, es oficial, para evaluaciones aceleradas de estabilidad oxidativa en aceites. A nivel industrial se usan técnicas convencionales basadas en indicadores fisicoquímicos, no existiendo estudios de correlación entre ellas y Rancimat. Este trabajo tiene por objetivo correlacionar el índice de estabilidad oxidativa (OSI en aceite de sacha inchi obtenido mediante Rancimat a temperaturas de 80º, 90º, 100º y 110 ºC bajo un flujo de aire de 15 L/h, con los valores de indicadores fisicoquímicos tales como Índice de peróxido, p-anisidina, totox y densidad. Asimismo estimar mediante extrapolación matemática, la vida útil del aceite de sacha inchi a temperaturas usuales de almacenamiento. Se encontró valores OSI de: 0,493 ± 0,01 h a 110 ºC, 1,590 ± 0,06 h a 100 ºC, 4,645 ± 0,1 h a 90 ºC y 20,512 ± 0,02 h a 80 ºC. Se ha establecido alta correlación entre valores de OSI vs índices fisicoquímicos de calidad (0,9322 < r < 0,9965. La energía de activación encontrada fue de 137,90 kJ/mol, lo que explica la alta estabilidad oxidativa para el aceite, estimándose una vida útil de 3,29, 1,79 y 0,79 años a 20, 25 y 30 °C respectivamente.

  16. Lump wood combustion process

    Science.gov (United States)

    Kubesa, Petr; Horák, Jiří; Branc, Michal; Krpec, Kamil; Hopan, František; Koloničný, Jan; Ochodek, Tadeáš; Drastichová, Vendula; Martiník, Lubomír; Malcho, Milan

    2014-08-01

    The article deals with the combustion process for lump wood in low-power fireplaces (units to dozens of kW). Such a combustion process is cyclical in its nature, and what combustion facility users are most interested in is the frequency, at which fuel needs to be stoked to the fireplace. The paper defines the basic terms such as burnout curve and burning rate curve, which are closely related to the stocking frequency. The fuel burning rate is directly dependent on the immediate thermal power of the fireplace. This is also related to the temperature achieved in the fireplace, magnitude of flue gas losses and the ability to generate conditions favouring the full burnout of the fuel's combustible component, which, at once ensures the minimum production of combustible pollutants. Another part of the paper describes experiments conducted in traditional fireplaces with a grate, at which well-dried lump wood was combusted.

  17. Estudio de la calidad del aceite de oliva virgen de Aragón

    Directory of Open Access Journals (Sweden)

    Herrera, A.

    2003-06-01

    Full Text Available The chemical composition of virgin olive oils (95 samples from Aragón (Spain from two successive crop seasons (1997/98 and 1998/99 and its relationship with quality and oxidative stability is examined. The main characteristics were: free acidity 0.5 (% oleic acid, peroxide value 11.8 meq/kg, K232 1.92, K270 0.13, oxidative stability 51.4 h (Rancimat method, and antioxidant phenolic substances 168.5 mg/kg (as caffeic acid. From the distribution of fatty acids, a high percentage of linoleic acid (9.46 % and a low level of stearic (2.10 % and arachidic (0.36 % acids, is worth noting. The effect of sample origin (7 productive regions from Aragón, olive variety (Empeltre and Arbequina, and the different steps through processing are also investigated. However, the major factor affecting results was the plague of olive flies during 1997/98 crop season.Se ha estudiado la composición química de 95 muestras de aceite de oliva virgen de Aragón procedente de dos campañas sucesivas (1997/98 y 1998/99 y su relación con la calidad y la estabilidad oxidativa. Las principales características fueron una acidez de 0,5 (% ácido oleico, índice de peróxidos 11,8 meq/kg, K232 1,92, K270 0,13, estabilidad a la oxidación 51,4 h (método Rancimat y contenido en polifenoles antioxidantes 168,5 mg/kg (como ácido caféico. Del perfil de ácidos grasos, destaca el elevado contenido en linoleico (9,46 % y las bajas tasas de esteárico (2,10 % y aráquico (0,36 %. Se analiza el efecto de la procedencia de las muestras (7 comarcas productoras de Aragón, de la variedad de la aceituna (Empeltre o Arbequina y de las distintas fases del procesado del aceite. Se destaca la gran influencia sobre la calidad del aceite de la plaga de mosca sufrida durante la campaña de 1997/98.

  18. Empleo de arcillas uruguayas pilareadas para el blanqueo de aceite de maiz.

    Directory of Open Access Journals (Sweden)

    Pagano, T.

    1998-02-01

    Full Text Available In the present paper adsorptive capacity to remove carotenes from a com oil by an Uruguayan montmorillonite modified by different treatments: exchange with Na+ ions (M-Na, acid-activation (Act, exchange with Ca2+ and pillaring with Keggin ions (Pile-Act, acid-activation and pillaring (Act Pil-Ca, is studied. Bleaching action of the Uruguayan modified montmorillonites is compared with two commercial days: Tonsil Optimum (Süd-Chemie and montmorillonite of type K 10 (Aldrich. Our results demonstrate that Act and Pilc-Ca samples are so efficient bleaching clays as commercials but M-Na sample Is lower. Also, mixtures of Pilc-Ca with commercial clays, added together in one step or consecutively in two steps, are studied. These procedures do not improved the bleaching action. As conclusion, the modified clay Pilc-Ca allows to bleach a neutralized and degummed corn oil, giving an end product similar to edible commercial oils. Such effect is improved with the simultaneous action with activated clays.

    En este trabajo se estudia la capacidad de adsorción de los carotenos presentes en un aceite de maíz, de una montmorillonita uruguaya modificada por diferentes procedimientos: intercambiada con iones Na+ (M-Na, activada por ácido (Act, intercambiada con iones Ca2+ y pilareada con iones Keggin (Pilc-Ca, activada por ácidos y pilareada (Act Pilc-Ca frente a dos arcillas comerciales: Tonsil Optimum de Süd-Chemie y una Montmorillonita tipo K 10 de Aldrich. Los resultados indican que la muestra Act y la Pilc-Ca son tan eficientes como las comerciales pero que la capacidad de la muestra M-Na es considerablemente menor. También se efectuó ensayos con mezclas de Pilc-Ca con las arcillas comerciales, colocadas simultáneamente (en una sola etapa o agregadas de manera sucesiva (en dos etapas. Dichos procedimientos no mejoraron la eficiencia del blanqueo. En conclusión, la modificación Pilc-Ca permite

  19. Emulsiones alimentarias aceite-en-agua estabilizadas con proteínas de atún

    Directory of Open Access Journals (Sweden)

    Ruiz-Márquez, D.

    2010-12-01

    Full Text Available This work is focused on the development of o/w salad dressing-type emulsions stabilized by tuna proteins. The influence of protein conservation methods after the extraction process (freezing or liofilization on the rheological properties and microstructure of these emulsions was analyzed. Processing variables during emulsification were also evaluated. Stable emulsions with adequate rheological and microstructural characteristics were prepared using 70% oil and 0.50% tuna proteins. From the experimental results obtained, we may conclude that emulsion rheological properties are not significantly affected by the protein conservation method selected. On the contrary, an increase in homogenization speed favours an increase in the values of the linear viscoelastic functions. Less significant is the fact that as agitation speed increases further, mean droplet size steadily decreases.

    El presente trabajo se ha centrado en el desarrollo de emulsiones alimentarias aceite-en-agua estabilizadas con proteínas de atún. Específicamente, se ha analizado la influencia del método de conservación de las proteínas aisladas (liofilización, congelación y de las condiciones de procesado seleccionadas sobre el comportamiento reológico y la microestructura de dichas emulsiones. Se han preparado emulsiones aceite en agua (con un contenido del 70% en peso de aceite estabilizadas con proteínas de atún. La concentración de emulsionante usada ha sido 0,50% en peso. El comportamiento reológico de estas emulsiones no depende significativamente del método de conservación de la proteína empleado. Por otra parte, un aumento de la velocidad de agitación durante el proceso de manufactura de la emulsión da lugar a una disminución continua del tamaño medio de gota y a un aumento de las funciones viscoelásticas dinámicas, menos significativo a medida que aumenta dicha velocidad de agitación.

  20. Flameless Combustion Workshop

    National Research Council Canada - National Science Library

    Gutmark, Ephraim

    2005-01-01

    .... "Flameless Combustion" is characterized by high stability levels with virtually no thermoacoustic instabilities, very low lean stability limits and therefore extremely low NOx production, efficient...

  1. Research Combustion Laboratory (RCL)

    Data.gov (United States)

    Federal Laboratory Consortium — The Research Combustion Laboratory (RCL) develops aerospace propulsion technology by performing tests on propulsion components and materials. Altitudes up to 137,000...

  2. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Paul Ziemkiewicz; Tamara Vandivort; Debra Pflughoeft-Hassett; Y. Paul Chugh; James Hower

    2008-08-31

    Ashlines: To promote and support the commercially viable and environmentally sound recycling of coal combustion byproducts for productive uses through scientific research, development, and field testing.

  3. Combustion Stratification for Naphtha from CI Combustion to PPC

    KAUST Repository

    Vallinayagam, R.; Vedharaj, S.; An, Yanzhao; Dawood, Alaaeldin; Izadi Najafabadi, Mohammad; Somers, Bart; Johansson, Bengt

    2017-01-01

    This study demonstrates the combustion stratification from conventional compression ignition (CI) combustion to partially premixed combustion (PPC). Experiments are performed in an optical CI engine at a speed of 1200 rpm for diesel and naphtha (RON

  4. Determinación de las propiedades físicas y carga crítica del aceite vegetal Jatropha curcas L // Determination of physical properties and critical load of Jatropha curcas L vegetable oil

    Directory of Open Access Journals (Sweden)

    Calixto Rodríguez-Martínez

    2012-09-01

    Full Text Available En el trabajo se determinaron las propiedades físicas y la carga critica del aceite de Jatropha curcas L, obtenido de las plantas cultivadas en la provincia de Guantánamo en Cuba. Estas propiedades fueron comparadas con las propiedades de otros aceites vegetales (aceite ricino, aceite de girasol, aceite de colza y aceite de soya usados como biolubricantes. Los resultados mostraron que las propiedades físicas del aceite de Jatropha curcas L fueron similares a la mayoría de los aceites vegetales. La carga crítica del aceite de la Jatropha curcas L ocupa una posición intermedia entre el aceite ricino y los aceites de girasol, colza y soya, lo cual permite asegurar que el aceite de Jatropha curcas L es un buen candidato para como biolubricante.Palabras claves: biolubricantes, aceites vegetales, Jatropha curcas L, propiedades físicas, carga crítica._______________________________________________________________________________AbstractIn this paper the physical properties and the critical load of the Jatropha curcas L oil, plantations located in Guantanamo province, Cuba were determined. These properties together with other vegetable oils (castor, sunflower, rapeseed and soybean oils used as biolubricant were compared. These results have showed that the physical properties of the Jatropha curcas L oil were similar to most of vegetable oils.The critical load of Jatropha curcas oil has an intermediate position just castor oil and sunflower, rapeseed and soybean oils. Jatropha curcas oil has good potential as the renewable energy as well as biolubricant feedstock.Key words: biolubricants, vegetable oils, Jatropha curcas L, physical properties, critical load.

  5. Combustion in fluidized bed reactors; Verbrennung in Wirbelschichtreaktoren

    Energy Technology Data Exchange (ETDEWEB)

    Thome-Kozmiensky, Karl J. [vivis CONSULT GmbH, Nietwerder (Germany)

    2013-03-01

    Since the first application for the coal gasification, the fluidized bed technology has passed an impressive development. Nowadays, the fluidized bed technology is utilized at chemical processes, drying and cooling, gasification, combustion and purification of exhaust gas. In the firing technology, the fluidized technology initially has been proved in the combustion of very high ash coal and sewage sludge. Recently, the fluidized bed technology also is applied in the drying of sewage sludge, combustion of domestic waste - as in Japan and Sweden - as well as in the gasification and combustion of substitute fuels, biomass - wood pellets, wood chips, straw, cocoa shells and so forth - and residues from the paper manufacturing - such as in Germany and Austria. Under this aspect, the author of the contribution under consideration reports on the combustion of sewage sludge, substitute fuels and biomass.

  6. Combustion mode switching with a turbocharged/supercharged engine

    Science.gov (United States)

    Mond, Alan; Jiang, Li

    2015-09-22

    A method for switching between low- and high-dilution combustion modes in an internal combustion engine having an intake passage with an exhaust-driven turbocharger, a crankshaft-driven positive displacement supercharger downstream of the turbocharger and having variable boost controllable with a supercharger bypass valve, and a throttle valve downstream of the supercharger. The current combustion mode and mass air flow are determined. A switch to the target combustion mode is commanded when an operating condition falls within a range of predetermined operating conditions. A target mass air flow to achieve a target air-fuel ratio corresponding to the current operating condition and the target combustion mode is determined. The degree of opening of the supercharger bypass valve and the throttle valve are controlled to achieve the target mass air flow. The amount of residual exhaust gas is manipulated.

  7. Dioxines, furans and other pollutants emissions bond to the combustion of natural and additive woods; Facteurs d'emission. Emissions de dioxines, de furanes et d'autres polluants liees a la combustion de bois naturels et adjuvantes

    Energy Technology Data Exchange (ETDEWEB)

    Collet, S

    2000-02-15

    This report deals especially on the dioxines and furans bond to the combustion of wood in industrial furnaces and domestic furnaces. It aims to define the environmental strategy which would allow the combustion of wood residues to produce energy. The first part recalls general aspects concerning the wood. The six other parts presents the wood resources and wastes, the additive used, the combustion and the different factors of combustion and finally the pollutants emissions. (A.L.B.)

  8. Combustion of poultry litter in a fluidised bed combustor

    Energy Technology Data Exchange (ETDEWEB)

    P. Abelha; I. Gulyurtlu; D. Boavida; J. Seabra Barros; I. Cabrita; J. Leahy; B. Kelleher; M. Leahy [DEECA-INETI, Lisbon (Portugal)

    2003-04-01

    Combustion studies of poultry litter alone or mixed with peat by 50% on weight basis were undertaken in an atmospheric bubbling fluidised bed. Because of high moisture content of poultry litter, there was some uncertainty whether the combustion could be sustained on 100% poultry litter and as peat is very available in Ireland, its presence was considered to help to improve the combustion. However, the results showed that, as long as the moisture content of poultry litter was kept below 25%, the combustion did not need the addition of peat. The main parameters that were investigated are (i) moisture content, (ii) air staging, and (iii) variations in excess air levels along the freeboard. The main conclusions of the results are (i) combustion was influenced very much by the conditions of the fuel supply, (ii) the steady fuel supply was strongly dependent on the moisture content of the poultry litter, (iii) temperature appeared to be still very influential in reducing the levels of unburned carbon and hydrocarbons released from residues, (iv) the air staging in the freeboard improved combustion efficiency by enhancing the combustion of volatiles released from residues in the riser and (vi) NOx emissions were influenced by air staging in the freeboard. Particles collected from the bed and the two cyclones were analysed to determine the levels of heavy metals and the leachability tests were carried out with ashes collected to verify whether or not they could safely be used in agricultural lands. 8 refs., 1 fig., 8 tabs.

  9. Strobes: An oscillatory combustion

    NARCIS (Netherlands)

    Corbel, J.M.L.; Lingen, J.N.J. van; Zevenbergen, J.F.; Gijzeman, O.L.J.; Meijerink, A.

    2012-01-01

    Strobe compositions belong to the class of solid combustions. They are mixtures of powdered ingredients. When ignited, the combustion front evolves in an oscillatory fashion, and flashes of light are produced by intermittence. They have fascinated many scientists since their discovery at the

  10. Catalytically enhanced combustion process

    International Nuclear Information System (INIS)

    Rodriguez, C.

    1992-01-01

    This patent describes a fuel having improved combustion efficiency. It comprises a petroleum based liquid hydrocarbon; and a combustion catalyst comprising from about 18 to about 21 weight percent naphthalene, from about 75 to about 80 weight percent toluene, and from about 2.8 to about 3.2 weight percent benzyl alcohol

  11. Fifteenth combustion research conference

    International Nuclear Information System (INIS)

    1993-01-01

    The BES research efforts cover chemical reaction theory, experimental dynamics and spectroscopy, thermodynamics of combustion intermediates, chemical kinetics, reaction mechanisms, combustion diagnostics, and fluid dynamics and chemically reacting flows. 98 papers and abstracts are included. Separate abstracts were prepared for the papers

  12. Estudio in vitro de la viabilidad de células Caco-2 en presencia de componentes del aceite esencial de Allium spp

    OpenAIRE

    M. Llana Ruiz-Cabello; M. Puerto; D. Gutiérrez-Praena; S. Pichardo; A. Jos; A. M. Cameán

    2013-01-01

    El aceite esencial de los componentes del género Allium, principalmente ajo y cebolla, presenta propiedades antioxidantes y antibacterianas debidas a la presencia de compuestos azufrados en su composición. La industria alimentaria ha comenzado a desarrollar nuevos sistemas de envasado activo a partir de polímeros seleccionados, a los que se incorporan aceites esenciales que, por sus propiedades, contribuyen a aumentar la vida útil de los alimentos perecederos. En este sentido, se hace necesar...

  13. The Heat of Combustion of Tobacco and Carbon Oxide Formation

    Directory of Open Access Journals (Sweden)

    Norman AB

    2014-12-01

    Full Text Available Recent studies demonstrated a relationship between mass burn rates of straight-grade cigarettes and heats of combustion of the tobacco materials. In the present work, relationships between measured heats of combustion and elemental composition of the tobacco materials were further analyzed. Heats of combustion measured in oxygen were directly correlated with the carbon and hydrogen content of the tobacco materials tested. Ash content of the materials was inversely related to the heats of combustion. The water insoluble residues from exhaustively extracted tobacco materials showed higher heats of combustion and higher carbon content than the non-extracted materials, confirming a direct relationship between carbon content and heat of combustion. A value for the heat of formation of tobacco was estimated (1175 cal/g from the heat of combustion data and elemental analysis results. The estimated value for heat of formation of tobacco appears to be constant regardless of the material type. Heat values measured in air were uniformly lower than the combustion heats in oxygen, suggesting formation of CO and other reaction products. Gases produced during bomb calorimetry experiments with five tobacco materials were analyzed for CO and CO2 content. When the materials were burned in oxygen, no CO was found in the gases produced. Measured heats of combustion matched estimates based on CO2 found in the gas and conversion of the sample hydrogen content to water. Materials burned in air produced CO2 (56% to 77% of the sample carbon content and appreciable amounts of CO (7% to 16% of the sample carbon content. Unburned residue containing carbon and hydrogen was found in the air combustion experiments. Estimated heat values based on amounts of CO and CO2 found in the gas and water formed from the hydrogen lost during combustion in air were higher than the measured values. These observations indicate formation of products containing hydrogen when the materials

  14. Evaluación in vitro de la actividad anti Trypanosoma cruzi de aceites esenciales de diez plantas medicinales

    Directory of Open Access Journals (Sweden)

    Juan Rojas

    2010-07-01

    Full Text Available Objetivos: Determinar la actividad anti Trypanosoma cruzi in vitro de los aceites esenciales de 10 plantas medicinales. Además, determinar la actividad citotóxica de los aceites contra células de mamíferos y la actividad modulatoria de los aceites sobre el óxido nítrico. Diseño: Estudio experimental in vitro. Institución: Instituto de Investigaciones Clínicas e Instituto de Medicina Tropical, Facultad de Medicina, Universidad Nacional Mayor de San Marcos, Lima, Perú. Material biológico: Epimastigotes de Trypanosoma cruzi, células Raw 264.7, aceites esenciales de Mentha X piperita L (menta, Rosmarinus officinalis L (romero, Chenopodium ambrosioides L (paico, Eucaliptus globulus Labill (eucalipto, Artemisia absinthium L (ajenjo, Melissa officinalis L (toronjil, Minthostachys setosa Brig (muña, Cimbopogon citratus (hierba luisa, Aloysia triphylla (cedrón y Mentha spicata L (hierba buena. Método: La actividad tripanocida se evaluó contra epimastigotes cultivados en medio LIT, incubados por 48 horas a 37ºC en incubador humidificado con CO2 al 5%. El cristal violeta se utilizó como control positivo. La actividad citotóxica de los productos contra células mamíferas se evaluó en células RAW 264.7 y la actividad modulatoria de los compuestos sobre óxido nítrico también se determinó en los cultivos de células RAW 264.7. Principales medidas de resultados: Porcentaje de inhibición de viabilidad y CI50. Resultados: Los aceites esenciales de Cymbopogon citratus (hierba luisa y Aloysia triphylla (cedrón inhibieron significativamente el crecimiento de la forma epimastigote de T. cruzi, con una CI50 de 63,09 y 96,49 μg/mL, respectivamente. No hubo variaciσn significativa de la concentraciσn de óxido nítrico y tampoco se evidenció citotoxicidad. Conclusiones: Los aceites esenciales de Cymbopogon citratus y Aloysia triphylla mostraron actividad anti-Trypanosoma cruzi in vitro y no fueron citotóxicas para las células mamíferas.

  15. Fuels and Combustion

    KAUST Repository

    Johansson, Bengt

    2016-08-17

    This chapter discusses the combustion processes and the link to the fuel properties that are suitable for them. It describes the basic three concepts, including spark ignition (SI) and compression ignition (CI), and homogeneous charge compression ignition (HCCI). The fuel used in a CI engine is vastly different from that in an SI engine. In an SI engine, the fuel should sustain high pressure and temperature without autoignition. Apart from the dominating SI and CI engines, it is also possible to operate with a type of combustion: autoignition. With HCCI, the fuel and air are fully premixed before combustion as in the SI engine, but combustion is started by the increased pressure and temperature during the compression stroke. Apart from the three combustion processes, there are also a few combined or intermediate concepts, such as Spark-Assisted Compression Ignition (SACI). Those concepts are discussed in terms of the requirements of fuel properties.

  16. Fuels and Combustion

    KAUST Repository

    Johansson, Bengt

    2016-01-01

    This chapter discusses the combustion processes and the link to the fuel properties that are suitable for them. It describes the basic three concepts, including spark ignition (SI) and compression ignition (CI), and homogeneous charge compression ignition (HCCI). The fuel used in a CI engine is vastly different from that in an SI engine. In an SI engine, the fuel should sustain high pressure and temperature without autoignition. Apart from the dominating SI and CI engines, it is also possible to operate with a type of combustion: autoignition. With HCCI, the fuel and air are fully premixed before combustion as in the SI engine, but combustion is started by the increased pressure and temperature during the compression stroke. Apart from the three combustion processes, there are also a few combined or intermediate concepts, such as Spark-Assisted Compression Ignition (SACI). Those concepts are discussed in terms of the requirements of fuel properties.

  17. PDF Modeling of Turbulent Combustion

    National Research Council Canada - National Science Library

    Pope, Stephen B

    2006-01-01

    .... The PDF approach to turbulent combustion has the advantages of fully representing the turbulent fluctuations of species and temperature, and of allowing realistic combustion chemistry to be implemented...

  18. Contenido de aceite en frutos de selecciones de aguacate (Persea americana criollo de clima tropical y subtropical de Nayarit, México

    Directory of Open Access Journals (Sweden)

    Raúl Medina Torres

    2017-07-01

    Full Text Available El trabajo se desarrolló sobre 65 selecciones de aguacate criollo de las zonas tropical y subtropical de Nayarit, con el objetivo de calificar el contenido de aceite y relacionarlo con el porcentaje de materia seca y del color de la pulpa del fruto, y de ubicar e identificar selecciones de interés comercial. Se usó análisis estadístico multivariado de componentes principales para el procesamiento de datos. Dos componentes principales explicaron el 63,93 % de la varianza total. En el componente principal 1 resultaron relevantes porcentaje de aceite y materia seca de la pulpa; y en el componente principal 2 las variables de color de la pulpa en madurez de consumo. Cuatro grupos de selecciones fueron identificadas por los promedios de los vectores característicos de los componentes 1 y 2. Se encontró alta correspondencia entre el contenido de aceite y materia seca en la pulpa (R2 = 0,9387 de los aguacates. El color de la pulpa del fruto no resultó un parámetro que se relacione con el contenido de aceite de la pulpa de aguacate. El contenido de materia seca puede constituir un parámetro fácil y útil para determinar con aproximación el contenido de aceite. En general, los aguacates de clima subtropical mostraron mayor contenido de aceite que los de origen tropical.

  19. Use of residue from paper processing as secondary raw material

    International Nuclear Information System (INIS)

    Ernstbrunner, L.

    1994-01-01

    In recent years, the paper industry has been trying to dispose of paper residues by thermal processes in its own, very expensive, combustion plants. Since 1990, the Wopfing Cement Factory, Austria, has been using paper residues in a process for which a patent has now been applied, in a similar way to the method used for the combustion of car tyres in cement rotary kilns. 30.000 t/yr of paper residue is to be processed in Wopfing cement plant from 1995, coming from PWA Ortmann, which is part of a large German paper concern. (author). 4 schemata

  20. Fuel Combustion Laboratory | Transportation Research | NREL

    Science.gov (United States)

    Fuel Combustion Laboratory Fuel Combustion Laboratory NREL's Fuel Combustion Laboratory focuses on designs, using both today's technology and future advanced combustion concepts. This lab supports the combustion chamber platform for fuel ignition kinetics research, was acquired to expand the lab's

  1. Estabilidad oxidativa del aceite de palma durante el proceso de refinación industrial en Costa Rica

    OpenAIRE

    Zamora, Eduardo; Herrera Ramírez, Carlos Hernán

    2002-01-01

    Se optimizó y validó un método para cuantificar la concentración del hierro y el cobre en aceites vegetales mediante la técnica de espectrofotometría de absorción atómica de llama. Se implementaron los métodos oficiales establecidos por la AOCS para la determinación de los productos oxidados: índices de peróxido (IP) y de p-anisidina (Ip-A), para evaluar el grado de deterioro del aceite de palma y su relación con el contenido de hierro y cobre, durante el proceso de refinación industrial. El ...

  2. Concentración y precios en el mercado mundial de aceite de palma 1985-2005

    Directory of Open Access Journals (Sweden)

    Jorge L. Navarro España

    2013-07-01

    Full Text Available El presente trabajo estudia la estructura del mercado mundial de aceite de palma, así como la in"uencia de dicha estructura sobre el nivel de precios. Para ello se hace uso del cálculo de índices de concentración de mercado y de estadísticos correlaciónales para establecer relaciones de causalidad. Los principales resultados muestran que a pesar que este mercado está fuertemente concentrado, esto no parece tener efectos sobre los precios. La explicación dada a esta situación es que se da por la alta sustitución entre los aceites de palma, girasol y soya, así como al hecho que las barreras de entrada no son los su#cientemente altas.

  3. Residual basins

    International Nuclear Information System (INIS)

    D'Elboux, C.V.; Paiva, I.B.

    1980-01-01

    Exploration for uranium carried out over a major portion of the Rio Grande do Sul Shield has revealed a number of small residual basins developed along glacially eroded channels of pre-Permian age. Mineralization of uranium occurs in two distinct sedimentary units. The lower unit consists of rhythmites overlain by a sequence of black shales, siltstones and coal seams, while the upper one is dominated by sandstones of probable fluvial origin. (Author) [pt

  4. Aceites vegetales sobre ácidos grasos y producción de metano in vitro en vacas lecheras.

    Directory of Open Access Journals (Sweden)

    Esperanza Prieto-Manrique

    2016-12-01

    Full Text Available El objetivo de este trabajo fue evaluar el efecto de la adición de aceites vegetales en dietas representativas de vacas lecheras bajo pastoreo, sobre los ácidos grasos, fermentación ruminal y producción de metano in vitro. La investigación se desarrolló en el laboratorio NUTRILAB–GRICA, perteneciente a la Facultad de Ciencias Agrarias, Universidad de Antioquia, Medellín, Colombia, en agosto del 2013. Se utilizó la técnica de producción de gas in vitro. En cuatro dietas (dos de monocultivo en Cynodon plectostachyus y dos de sistema silvopastoril intensivo con Leucaena leucocephala, se evaluó la adición de tres aceites vegetales (girasol, lino y palma a nivel del 2 y 4% de la MS, en un diseño completamente al azar con arreglo factorial de 4x3x2. En todas las dietas, la suplementación con aceite de girasol aumentó el contenido de ácido linoleico (C18:2 c9,12, ácido linoleico conjugado (ALC-c9t11 y ácido transvaccénico (ATV, C18:1 t11 después de la fermentación (p0,05. Ningún aceite afectó la cinética de fermentación, pH, total de ácidos grasos volátiles (AGV, proporción de AGV, ni la producción de metano.

  5. Efecto antitumoral in vitro del aceite esencial de Piper aduncum L. (matico y su toxicidad oral en ratones

    Directory of Open Access Journals (Sweden)

    Jorge Arroyo

    2014-01-01

    Full Text Available Introducción: Piper aduncum (matico es una especie utilizada por sus propiedades medicinales en desórdenes gastrointestinales y genitourinarios. Objetivos: Evaluar el efecto antitumoral del aceite esencial de Piper aduncum (matico in vitro en siete líneas celulares tumorales humanas y determinar la toxicidad oral en ratones. Diseño: Experimental. Institución: Facultad de Medicina, Universidad Nacional Mayor de San Marcos, Lima, Perú. Material biológico: Líneas celulares tumorales humanas H460, DU-145, ME-180, K562, HT-29, MCF 7, M14, K562; fibroblastos normales de ratón 3T3 y ratones albinos machos Balb/C53. Intervenciones: Las líneas celulares fueron expuestas a cuatro concentraciones del aceite esencial de P. aduncum y 5-fluorouracilo (5-FU. Para la toxicidad oral se utilizó ratones albinos machos Balb C/53 de 40 días post destete, a cinco dosis de tratamiento, evaluándose el número de muertes en cada dosis. Principales medidas de los resultados: Porcentaje de inhibición del crecimiento celular (IC50, dosis letal 50 (DL50. Resultados: El aceite esencial mostró IC50 mayor a 250 ug/mL para las líneas celulares M-14 (r = -0,99; p 2 000 mg /kg. Conclusiones: El aceite esencial de P. aduncum no presentó efecto antitumoral in vitro para las siete líneas celulares tumorales humanas y no fue tóxico.

  6. 40 CFR 60.2020 - What combustion units are exempt from this subpart?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What combustion units are exempt from..., 2001 Applicability § 60.2020 What combustion units are exempt from this subpart? This subpart exempts... byproduct streams/residues containing catalyst metals which are reclaimed and reused as catalysts or used to...

  7. Producción de biodiesel de aceite crudo de palma mediante catálisis heterogénea

    Directory of Open Access Journals (Sweden)

    Fernando Cardeño

    2010-01-01

    Full Text Available Se estudió la producción de biodiesel de aceite crudo de palma mediante el uso de catalizadores heterogéneos ácidos y básicos para las etapas de preesterificación y transesterificación respectivamente. La pre-esterificación es necesaria para aceites con una acidez superior al 4% de ácidos grasos libres, ya que se evitan los problemas asociados con la formación de jabones. En ambas reacciones las variables analizadas fueron el tipo de catalizador, la temperatura y el tiempo. Se analizó la conversión del aceite a metilésteres usando cromatografía gaseosa y la estabilidad de los catalizadores mediante su reutilización. En la etapa de pre-esterificación se encontró que catalizadores ácidos del tipo resinas de poliestireno sulfonadas presentan conversiones superiores al 87% estabilidad para la esterificación de los ácidos grasos libres. Para la transesterificación se estudiaron como catalizadores heterogéneos, el carbonato de potasio libre y soportado en una matriz polimérica, obteniéndose con ambos conversiones superiores a 95 % de biodiesel; con el uso del soporte polimérico se disminuyó la velocidad de disolución de carbonato de potasio, permitiendo su reutilización hasta 10 reutilizaciones.

  8. Efecto del aceite esencial de Cymbopogon citratus sobre propiedades fisicoquímicas en películas de quitosano

    Directory of Open Access Journals (Sweden)

    María del Carmen Vázquez - Briones

    2017-01-01

    Full Text Available Se investigó el efecto de la incorporación de aceite esencial de zacate limón ( Cymbopogon citratus , en concentraciones de 0, 200 y 400 ppm, en las propiedades fisicoquímicas (espesor, humedad, solubilidad, permeabilidad al vapor de agua, color, transparencia y mecánicas (resistencia a la tensión y elongación de películas de quitosano a dos concentraciones (1 y 3%. Los resultados mostraron un efecto significativo (p ≤ 0,05 en los valores del espesor de las películas a las dos concentraciones de quitosano. Se observó un efecto significativo (p ≤ 0,05 en los valores de humedad a concentraciones de 0, 200 y 400 ppm de aceite esencial. La adición de aceite esencial en películas de quitosano mostró un efecto significativo (p ≤ 0,05 en los valores de permeabili dad al vapor de agua. La concentración de quitosano mostró un efecto significativo (p ≤ 0,05 en transparencia y en los parámetros de color L* , a* , b* . Al variar la concentración de quitosano se observó un incremento significativo (p ≤ 0,05 en los valores de resistencia a la tensión de las películas de quitosano.

  9. Estudio del comportamiento térmico y la composición de aceites para el curtido de cueros

    Directory of Open Access Journals (Sweden)

    Grompone, M. A.

    2000-06-01

    Full Text Available The leather industry uses fatty materials to give leather certain characteristics. Neatsfoot oil, a material with variable cost and disponibility, has been used traditionally. Samples of neatsfoot, chicken, fish and rice bran oils are studied in this work. They are evaluated as potential raw materials for leather tanning derivatives, according to their thermal behaviour (Cold Test and DSC and main fatty acids composition (GC. Some seem adequate for that purpose, while others could be modified through thermal fractionation.La industria del cuero utiliza materiales grasos que otorgan determinadas características al cuero. Tradicionalmente se ha usado, entre otros, el aceite de patas de vacuno, producto cuya disponibilidad y costo son muy variables. En este trabajo se estudiaron muestras de distintos aceites de patas de vacuno, de pollo, de pescado y de salvado de arroz. Fueron evaluadas como potenciales materias primas para la obtención de derivados para el curtido de cueros, en función de su comportamiento térmico (“Cold Test” y DSC, y su composición en ácidos grasos principales (GC. Algunos de los aceites estudiados aparecen como adecuados para dicho uso, mientras que otros podrían ser mejorados por fraccionamiento térmico.

  10. User`s guide for the Augmented Computer Exercise for Inspection Training (ACE-IT), Version 2.0 software

    Energy Technology Data Exchange (ETDEWEB)

    Dobranich, P.R. [Sandia National Labs., Albuquerque, NM (United States); Horak, K.E.; Evanko, D.A. [Excel Tactical Staffing, Albuquerque, NM (United States)] [and others

    1998-04-01

    The on-site inspection provisions in many current and proposed arms control agreements require extensive preparation and training on the part of both the Inspection Teams (inspectors) and Inspected Parties (hosts). Traditional training techniques include lectures, table-top inspections, and practice inspections. The Augmented Computer Exercise for Inspection Training (ACE-IT), an interactive computer training tool, increases the utility of table-top inspections. ACE-IT is used for training both inspectors and hosts to conduct a hypothetical challenge inspection under the Chemical Weapons Convention (CWC). The training covers the entire sequence of events in the challenge inspection regime, from initial notification of an inspection through post-inspection activities. The primary emphasis of the training tool is on conducting the inspection itself, and in particular, implementing the concept of managed access. (Managed access is a technique used to assure the inspectors that the facility is in compliance with the CWC, while at the same time protecting sensitive information unrelated to the CWC.) Information for all of the activities is located in the electronic {open_quotes}Exercise Manual.{close_quotes} In addition, interactive menus are used to negotiate access to each room and to alternate information during the simulated inspection. ACE-IT also demonstrates how various inspection provisions impact compliance determination and the protection of sensitive information.

  11. Experimentacion y Optimizacion Conjunta de la Disrupcion Celular de Microalgas y Extraccion Soxhletde Aceite Para Alimentacion y Biocombustibles

    Directory of Open Access Journals (Sweden)

    Angel D González Delgado

    2014-03-01

    Full Text Available La producción de biocombustibles y bioproductos utilizando microalgas puede realizarse con tratamientos térmicos para producir biocrudo, o mediante la extracción y transformación de metabolitos específicos. Esta última alternativa incluye las etapas de cultivo, cosecha, secado, extracción de lípidos y purificación o transformación de los mismos. La factibilidad técnica y económica de la obtención de bioproductos derivados del aceite de microalgas depende en gran medida de la eficiencia de extracción de los lípidos. El objetivo principal de este trabajo es establecer una metodología para la disrupción celular y extracción soxhlet de aceite de microalgas, y determinar su efectividad en tres cepas nativas; Amphiprora, Desmodesmus y Tetraselmis. Se evaluó el efecto de distintos métodos de disrupción celular como MSA, MHA, HA4M Fast, y HA0.5M Slow,solventes como hexano, ciclohexano y metanol, y tiempos de extracción de 4,6 y 8 horas, sobre la cantidad de aceite extraído. La mayor eficiencia de extracción se obtuvo utilizando disrupción celular MSA. El mejor solvente fue hexano y el mejor tiempo de extracción fue de 8 horas.

  12. Sandia Combustion Research: Technical review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    This report contains reports from research programs conducted at the Sandia Combustion Research Facility. Research is presented under the following topics: laser based diagnostics; combustion chemistry; reacting flow; combustion in engines and commercial burners; coal combustion; and industrial processing. Individual projects were processed separately for entry onto the DOE databases.

  13. Producción de lípidos estructurados por transesterificación enzimática del aceite de soja y aceite de palmiste en reactor de lecho empacado

    Directory of Open Access Journals (Sweden)

    Perea Villamil, Aide

    2008-12-01

    Full Text Available Enzymatic synthesis of structured lipids by transesterification of soybean oil with palm kernel oil was evaluated in a packed-bed reactor with a capacity for 500g of enzyme loading. Lipozyme RM-IM was used as catalyst. Substrate blends were passed through the enzyme bed at different flow rates. Transesterification reached a level of 19.6 %, with a maximum calculated productivity of 2344 kg of transesterified oil/kg of immobilized enzyme, a flow rate of 9,36 kg oil/kg enzyme/h. The triacylglycerols formed in major proportion were C40:2, C42:2, C42:3, C44:2, C44:3, C50:3 and C50:4. Stereoespecific analysis of the fat before and after transesterification shows a slight migration of acyl groups. The products obtained by this technology can be applied in the formulation of lipid emulsions for enteral and parenteral nutrition and the food industry.Se evaluó la síntesis enzimática de lípidos estructura-dos por transesterificación de aceite de soja con aceite de palmiste en un reactor de lecho empacado (PBR con capacidad para 500 gramos de enzima, utilizando como catalizador Lipozyme RM-IM. La mezcla de sustratos se hizo pasar a través del lecho de enzima a 70 °C y diferentes flujos de aceite. A un flujo de 9.36 kg aceite/kg enzima/h se alcanzó un grado transesterificación de 19.6 % con una productividad máxima calculada de 2344 kg aceite/kg enzima. Los triacilgliceroles que se formaron en mayor proporción fueron el C40:2, C42:2, C42:3, C44:2, C44:3, C50:3 y C50:4. El análisis estereoespecífico de la mezcla grasa antes y después de la transesterificación indicó baja migración de grupos acilo. Los productos obtenidos pueden tener aplicación en la formulación de emulsiones lípidicas para nutrición enteral y parenteral y en la industria de alimentos.

  14. Shale oil combustion

    International Nuclear Information System (INIS)

    Al-dabbas, M.A.

    1992-05-01

    A 'coutant' carbon steel combustion chamber cooled by water jacket was conslructed to burn diesel fuel and mixlure of shale oil and diesel fuels. During experimental work nir fuel ratio was determined, temperaturces were measured using Chromel/ Almel thermocouple, finally the gasous combustion product analysis was carricd out using gas chromatograph technique. The constructed combustion chamber was operating salisfactory for several hours of continous work. According to the measurements it was found that: the flame temperature of a mixture of diesel and shale oil fuels was greater than the flame temperature of diesel fuel. and the sulfer emissious of a mixture of diesel and shale oil fuels was higher than that of diesel fuel. Calculation indicated that the dry gas energy loss was very high and the incomplete combustion energy loss very small. (author). 23 refs., 35 figs

  15. Shale oil combustion

    Energy Technology Data Exchange (ETDEWEB)

    Al-dabbas, M A

    1992-05-01

    A `coutant` carbon steel combustion chamber cooled by water jacket was conslructed to burn diesel fuel and mixlure of shale oil and diesel fuels. During experimental work nir fuel ratio was determined, temperaturces were measured using Chromel/ Almel thermocouple, finally the gasous combustion product analysis was carricd out using gas chromatograph technique. The constructed combustion chamber was operating salisfactory for several hours of continous work. According to the measurements it was found that: the flame temperature of a mixture of diesel and shale oil fuels was greater than the flame temperature of diesel fuel. and the sulfer emissious of a mixture of diesel and shale oil fuels was higher than that of diesel fuel. Calculation indicated that the dry gas energy loss was very high and the incomplete combustion energy loss very small. (author). 23 refs., 35 figs.

  16. Indoor combustion and asthma.

    Science.gov (United States)

    Belanger, Kathleen; Triche, Elizabeth W

    2008-08-01

    Indoor combustion produces both gases (eg, nitrogen dioxide, carbon monoxide) and particulate matter that may affect the development or exacerbation of asthma. Sources in the home include both heating devices (eg, fireplaces, woodstoves, kerosene heaters, flued [ie, vented] or nonflued gas heaters) and gas stoves for cooking. This article highlights the recent literature examining associations between exposure to indoor combustion and asthma development and severity. Since asthma is a chronic condition affecting both children and adults, both age groups are included in this article. Overall, there is some evidence of an association between exposure to indoor combustion and asthma, particularly asthma symptoms in children. Some sources of combustion such as coal stoves have been more consistently associated with these outcomes than other sources such as woodstoves.

  17. El aceite de pescado atenua las crisis convulsivas inducidas por hipertermia en ratas neonatas

    Directory of Open Access Journals (Sweden)

    Leopoldo E. Flores M.

    2008-01-01

    Full Text Available Un alto porcentaje (50-60% del cerebro en los mamíferos son principalmente grasas o lípidos, de éstos, el 35% son ácidos grasos esenciales, en particular los llamados omegas (O, como el Acido Docosahexanoico (DHA y el Eicosapentanoico (EPA llamados omega 3 (O-3. Diversos estudios han mostrado beneficios en la salud con la implementación de los O-3 como agentes terapéuticos en alteraciones cardiovasculares, renales, dérmicas, metabólicas, neurodegenerativas e inmunológicas. Evidencias experimentales sugieren un beneficio potencial del aceite de pescado (APE como neuroprotector debido al alto contenido de DHA y EPA. Sin embargo, es poco lo que se conoce en cuanto a los efectos que pudieran tener sobre alteraciones nerviosas, como las crisis convulsivas. En este contexto, se ha reportado que el tipo más común de trastorno epiléptico observado en los niños son las crisis convulsivas provocadas por fiebre (CF. La incidencia es de 3-5%, con ocurrencia entre los 5 meses y 5 años de edad, y se ha propuesto que esta alteración en la vida temprana pudiera tener efectos a largo plazo, manifestándose como un síndrome de epilepsia en la vida adulta. El objetivo del presente estudio fue evaluar el efecto del APE sobre las convulsiones inducidas por hipertermia experimental en un grupo de ratas Wistar macho de 5 días de edad (grupo SAPE cuyas madres consumieron una dieta base más un suplemento de APE (suministrado desde su infancia hasta la etapa de crianza. Este grupo se comparó con otro grupo de ratas de la misma edad y cepa (grupo SAPA cuyas madres consumieron una dieta base más un suplemento de aceite de palma (suministrado desde su infancia hasta la etapa de crianza, y con un tercer grupo de ratas (grupo CTRL cuyas madres consumieron la dieta base más agua bidestilada como suplemento. Las ratas tratadas con APE presentaron mayor resistencia a la elevación de la temperatura corporal inducida por la hipertermia, una menor frecuencia

  18. Sandia Combustion Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, S.C.; Palmer, R.E.; Montana, C.A. (eds.)

    1988-01-01

    During the late 1970s, in response to a national energy crisis, Sandia proposed to the US Department of Energy (DOE) a new, ambitious program in combustion research. Shortly thereafter, the Combustion Research Facility (CRF) was established at Sandia's Livermore location. Designated a ''user facility,'' the charter of the CRF was to develop and maintain special-purpose resources to support a nationwide initiative-involving US inventories, industry, and national laboratories--to improve our understanding and control of combustion. This report includes descriptions several research projects which have been simulated by working groups and involve the on-site participation of industry scientists. DOE's Industry Technology Fellowship program, supported through the Office of Energy Research, has been instrumental in the success of some of these joint efforts. The remainder of this report presents results of calendar year 1988, separated thematically into eleven categories. Referred journal articles appearing in print during 1988 and selected other publications are included at the end of Section 11. Our traditional'' research activities--combustion chemistry, reacting flows, diagnostics, engine and coal combustion--have been supplemented by a new effort aimed at understanding combustion-related issues in the management of toxic and hazardous materials.

  19. Estudio de la hidrogenación del aceite de jojoba

    Directory of Open Access Journals (Sweden)

    Pramparo, María C.

    2009-03-01

    Full Text Available Trials were cattied out on jojoba oil hydrogenation to study the effects of the main operative variable on iodine index and melting point. . A batch reactor with nickel catalysts was used. The effects selected for analysis were the reaction temperature, the operation pressure and the amount of catalyst.The range of temperature studied was 120-200ºC, the pressure was between 2 and 4 atm and the amount of catalyst ranged from 0.2 - 0.6% (percentage of catalyst mass over oil mass. The results showed that these three factors affected the reaction significantly; although temperature was the most influential in the progression of the reaction. In addition, the kinetic behavior was studied using a potential model of pseudo-first order and the corresponding kinetic parameters were obtained.Se han llevado a cabo ensayos de hidrogenación de aceite de jojoba para estudiar los efectos de las principales variables operativas de esta operación sobre el índice de yodo y el punto de fusión. Se utilizó un reactor discontinuo con un catalizador de níquel. Los efectos seleccionados para su análisis fueron la temperatura de reacción, la presión de operación y la cantidad de catalizador. El rango de temperaturas estudiado fue de 120-200ºC, el de presión entre 2 y 4 atm y la cantidad de catalizador entre 0,2-0,6 % (% masa catalizador / masa de aceite. Si bien los tres efectos estudiados fueron significativos, la temperatura fue el efecto que más influencia tuvo sobre el avance de la reacción. Se estudió además el comportamiento cinético mediante el ajuste de un modelo potencial de pseudo-primer orden, obteniéndose los parámetros cinéticos correspondientes.

  20. Caracterización del aceite de coquito de palma chilena (Jubaea chilensis

    Directory of Open Access Journals (Sweden)

    Torija, M. Esperanza

    2008-03-01

    Full Text Available The characteristics of the seeds from Chilean palm and the detailed composition of its fat are studied starting from 4 lots of seeds from the two regions being the major producers of Chilean palm seeds. From the proximate composition of the seeds a high content of fats is deduced with a mean value of 67.3%. The contents of proteins, carbohydrates and fibre were in the range of 7-11%. A detailed analysis of the fat indicates a high content of saturated fatty acids being capric, caprilic, lauric and miristic acids the major fatty acids. For this reason the presence of a high percentage of medium-chain triglycerides are detected in the triglyceride analysis. As for tocopherols, the fat contains low amounts of α-, γ- y δ-tocopherol with a total average of 84 mg/kg. Concerning phytosterols, the total content was around 1000 mg/kg being β-sitosterol and Δ7-estigmastenol the two major sterolsSe analizan las características generales del coquito de palma chilena y se estudia con detalle la composición de su aceite. Con este objetivo, se analizan 4 lotes de coquitos procedentes de las dos regiones de Chile donde existe mayor producción. La composición proximal del coquito indica un contenido muy mayoritario de grasa, con un promedio de 67,3% mientras los contenidos de proteínas, hidratos de carbono y fibra se encuentran entre el 7 y el 11%. Un análisis detallado de la grasa muestra un contenido elevado de ácidos grasos saturados (alrededor del 85% siendo los ácidos cáprico, caprílico, láurico y mirístico los que se encuentran en mayor concentración, lo que origina un elevado porcentaje de triglicéridos de cadena media. Respecto a los tocoferoles, el aceite contiene cantidades limitadas de α-, γ- y δ-tocoferol con un valor promedio total de 84 mg/kg, no detectándose la presencia de tocotrienoles. Respecto a los fitoesteroles, el contenido total es del orden de 1000 mg/kg siendo los esteroles mayoritarios el

  1. Características fisicoquímicas del aceite del endospermo de la Palma Yagua (Attalea cryptanther

    Directory of Open Access Journals (Sweden)

    Linares, Oscar

    2006-09-01

    Full Text Available In this research, the physicochemical characteristics of the yagua palm (Attalea cryptanther endospermus oil were evaluated. Seeds of mature fruits from Santa Ana hill, Canoabo, Bejuma municipality, Carabobo state-Venezuela, harvested in November 2003, were decorticated and the endospermus was transformed to meal by means of grinding. The oil from meal was extracted with n-hexane using Soxhlet equipment. Yagua endospermus crude oil showed the following characteristics: iodine index 13.77 cg I2/g; refraction index 1.4441 at 60 ºC; saponification value 233 mg KOH/g; peroxide value 0.20 meq O2/kg; unsaponifiable matter 0.97 %; AOM stability 31 h; solid fat content 54 % at 10 ºC and 10 % at 20 ºC; Lovibond color: R 3.2 and Y 1.3. The major fatty acids were lauric acid (58 % and miristic acid (16.5 %.Yagua endospermus is an alternative oleaginousEl objetivo de esta investigación fue caracterizar físicoquímicamente el aceite de la palma Yagua (Attalea cryptanther. El endospermo de frutos maduros procedentes del cerro Santa Ana, Canoabo, municipio Bejuma, estado Carabobo Venezuela, pertenecientes a la cosecha Noviembre 2003, fueron transformados en harina mediante molienda. Una vez obtenida la harina se procedió a la extracción del aceite mediante un equipo Soxhlet utilizando como solvente n-Hexano. El aceite crudo extraído fue caracterizado mediante normas COVENIN y AOCS. Se determinaron valores de índice de yodo de 13,77 cg I2/g, índice de refracción 1,4441 a 60 °C, índice de saponificación 233mg KOH/g, índice de peroxido 0,20 meq O2/Kg, materia insaponificable 0,97%, estabilidad AOM (31 horas, contenido de grasa sólida (54% a 10 °C y 10% a 20 °C, color (R: 3,2- A: 1,3-A: 0. Los ácidos grasos mayoritarios encontrados fueron el ácido laurico (58% y el ácido miristico (16,5%. El endospermo evaluado es una alternativa como materia prima para la obtención de aceite ya que presenta características similares al aceite de coco y

  2. Efecto de algunos aceites esenciales sobre el crecimiento de Phytophthora infestans (Mont. de Bary en condiciones de laboratorio

    Directory of Open Access Journals (Sweden)

    Carrillo Yazmid Adriana

    2010-08-01

    Full Text Available Entre los factores más limitantes del cultivo de papa se encuentra
    Phytophthora infestans, agente causal de la llamada “gota”.
    El control químico de esta enfermedad representa entre el 7 y
    el 10% de los costos totales del cultivo, y tiene un alto impacto
    ambiental por la contaminación que ocasiona. La búsqueda
    y aplicación de prácticas alternativas para el control de este
    patógeno es importante para disminuir tanto la utilización de
    fungicidas como los costos de producción del cultivo. Numerosos
    estudios realizados in vitro demuestran que algunos aceites
    esenciales tienen propiedades fungicidas y fungistáticas sobre
    diferentes patógenos. Por ello, el objetivo del presente estudio
    consistio en la evaluacion de ocho aceites esenciales extraidos
    de algunas especies aromaticas de la familia Lamiaceae sobre
    el crecimiento de P. infestans en condiciones de laboratorio. Se
    evaluaron diferentes metodologías de aplicación de los productos
    en estudio, encontrándose que las mas apropiadas son aquellas
    en que el aceite ejerce un efecto volátil. Los aceites esenciales
    fueron Origanum vulgare, Mentha piperita, Salvia officinalis,
    Ocimum basilicum, Rosmarinus officinalis, Origanum majorana,
    Thymus vulgaris y Pogostemon cablin se evaluaron en
    su fase volatil, a traves de su efecto sobre dos aislamientos
    de P. infestans (A13 y A15. Los aceites que mostraron efecto
    inhibitorio sobre el crecimiento de P. infestans fueron los de T.
    vulgaris y M. piperita, los cuales redujeron el crecimiento del
    hongo en 92,1 y 89,9%, respectivamente; y por ello pueden ser
    considerados promisorios para ser evaluados en campo.

  3. Efecto anti-Trypanosoma cruzi del aceite esencial de Cymbopogon citratus (DC Stapf (hierba luisa en ratones Balb/c

    Directory of Open Access Journals (Sweden)

    Juan Rojas

    2012-01-01

    Full Text Available Objetivo: Determinar la actividad anti-Trypanosoma cruzi in vivo del aceite esencial de Cymbopogon citratus en ratones Balb/c. Diseño: Estudio experimental, prospectivo. Institución: Instituto de Investigaciones Clínicas e Instituto de Medicina Tropical de la Facultad de Medicina de la Universidad Nacional Mayor de San Marcos, Lima, Perú. Material biológico: Aceite esencial de Cymbopogon citratus; ratones albinos Balb/c. Intervenciones: Los animales fueron asignados aleatoriamente a seis grupos de 15 ratones cada uno: infectados y no tratados (G1, infectados y tratados con benznidazol 100 mg/kg (G2, infectados y tratados con aceite esencial de Cymbopogon citratus 100 mg/kg y 250 mg/kg (G3 y G4, respectivamente, no infectados y no tratados (G5, y no infectados y tratados con 250 mg de Cymbopogon citratus (G6. La infección con T. cruzi se realizó con 10(4 trypomastigotes sanguíneos y el tratamiento empezó en el 8º día post infección (dpi hasta el 28° dpi. La parasitemia se determinó con microscopia óptica cada dos días en 5 µL de sangre de la cola. En el 14°, 21° y 28° dpi, cinco animales de cada grupo fueron sacrificados y se removió el corazón para estudio histopatológico. Principales medidas de resultados: Parasitemia, número de nidos de amastigotes e infiltrados inflamatorios. Resultados: El aceite esencial de Cymbopogon citratus 250 mg/kg/día produjo una reducción significativa en el pico de parasitemia desde 113,92 ± 25,66 hasta 74,60 ± 12,37 tripomastigotes/mL (p < 0,05. Con 100 mg/kg/día se produjo una reducción hasta 77,40 ± 14,93 tripomastigotes/ mL (p < 0,05. También redujo el número de amastigotes y de infiltrados inflamatorios en el corazón. Conclusiones: El aceite esencial de Cymbopogon citratus tuvo efecto anti-Trypanosoma cruzi en ratones Balb/c en lo referente a la disminución de la parasitemia, el número de nidos de amastigotes y los resultados inflamatorios.

  4. Detection of olive oil adulteration by low-field NMR relaxometry and UV-Vis spectroscopy upon mixing olive oil with various edible oils; Detección de la adulteración de aceite de oliva mediante relaxometría magnética nuclear de campo bajo y espectroscopía UV-Vis sobre mezcla de aceite de oliva con diversos aceites comestibles.

    Energy Technology Data Exchange (ETDEWEB)

    Ok, S.

    2017-07-01

    Adulteration of olive oil using unhealthy substitutes is considered a threat for public health. Low-field (LF) proton (1H) nuclear magnetic resonance (NMR) relaxometry and ultra-violet (UV) visible spectroscopy are used to detect adulteration of olive oil. Three different olive oil with different oleoyl acyl contents were mixed with almond, castor, corn, and sesame oils with three volumetric ratios, respectively. In addition, Arbequina olive oil was mixed with canola, flax, grape seed, peanut, soybean, and sunflower seed oils with three volumetric ratios. Transverse magnetization relaxation time (T2) curves were fitted with bi-exponential decaying functions. T2 times of each mixture of olive oils and castor oils, and olive oils and corn oils changed systematically as a function of volumetric ratio. To detect the adulteration in the mixtures with almond and sesame oils, both LF 1H NMR relaxometry and UV-Vis spectroscopy were needed, where UV-Vis-spectroscopy detected the adulteration qualitatively. In the mixtures of Arbequina olive oil and flax, peanut, soybean, and sunflower seed oils, both T21 and T22 values became longer systematically as the content of the olive oil was decreased. The unique UV-Vis maximum absorbance of flax oil at 320.0 nm shows the adulteration of olive oil qualitatively. [Spanish] La adulteración del aceite de oliva con sustituyentes menos saludables es una amenaza para la salud pública. En este trabajo, la detección de la adulteración del aceite de oliva se demuestra utilizando tanto relaxometría magnética nuclear de campo bajo (LF) de protones (1H) (RMN) y espectroscopía visible y ultra-violeta (UV). Tres muestras de aceites de oliva con diferentes contenidos en oleico se mezclaron con aceites de almendra, ricino, maíz y sésamo con tres relaciones volumétricas. Además, el de arbequina de California se mezcló con cánola, lino, semilla de uva, cacahuete, soja y aceites de girasol con tres relaciones volumétricas. Las curvas de

  5. Combustion Characterization of Individual Bio-oil Droplets

    DEFF Research Database (Denmark)

    Hansen, Brian Brun; Jensen, Peter Arendt

    2015-01-01

    Single droplet combustion characteristics has been investigated for bio-oil slurries, containing biomass residue, and compared to conventional fuels for pulverized burners, such as fuel oil (start up) and wood chips (solid biomass fuel). The investigated fuels ignition delays and pyrolysis behavior...

  6. Use of solid residue from the olive industry

    Directory of Open Access Journals (Sweden)

    Guinda, Ángeles

    2006-03-01

    Full Text Available Research into finding new uses for olive products, particularly by-products of olive oil production, is of great relevance not only to the economy, but also to the environment, in the towns where olives are grown. A large number of research articles has been published dealing with the chemical composition of olives and olive oil; however, only a few studies have centered on isolating and identifying compounds in the olive leaf. In this article an overview of the present body of knowledge on the chemical composition of the olive leaf will be presented. Also to be discussed is the use of solid residue, namely, the olive leaf and the olive stone. Both of these types of residue result from olive oil and table olive production, and can be used as a renewable energy source, as well as to obtain high added-value compounds. The latter, bioactive compounds are directed towards the cosmetic, pharmaceutical, and natural food supplements markets, all of which are currently highly receptive to products of natural origin.La investigación de nuevos aprovechamientos del olivar y en particular de lo subproductos del proceso de producción del aceite, tiene gran relevancia tanto en la economía como en el medio ambiente de los pueblos donde se desarrolla este cultivo. Son numerosos los trabajos publicados sobre la composición química de la aceituna y el aceite de oliva, en cambio sólo existen algunos estudios sobre el aislamiento e identificación de los compuestos de la hoja de olivo, en esta contribución se revisan los conocimientos sobre la composición química de la hoja de olivo, así como, las utilizaciones de los residuos sólidos -hoja de olivo y hueso de aceituna- que se originan en la producción del aceite de oliva y de aceitunas de mesa, como energía renovable y para la obtención de compuestos de alto valor añadido. Estos últimos, compuestos bioactivos dirigidos a los mercados de los aditivos alimentarios naturales, farmacéutico y cosm

  7. Evaluación de la calidad del aceite de once semillas de leguminosas del desierto sonorense

    Directory of Open Access Journals (Sweden)

    Ortega-Nieblas, M.

    1996-06-01

    Full Text Available In order to generate information that lead to an efficient and diversifícate use of the natural resources that the Sonoran Desert offers, as it is the great variety of Leguminosae or Fabaceae plants, oils from seeds or Prosopis chilensis, Prosopis velutina (mezquite, Cercidium floridium (palo azul, Cercidium praecox (palo de brea, Acacia constricta (vinorama, Acacia cymbyspina (chirahui, Acacia occidentalis (tesota, Acacia mcmurphy (tepehuaje, Desmanthus palmeri (mezquitillo, Caesalpinia caladenia (palo dorado, and Caesalpinia pumila (palo piojo were analyzed. The oils were extracted from each seed with hexane, and their physicochemical characteristics were evaluated. The oil content varied from 9 to 16% in the different seeds. Their indexes of acidity, peroxides and free fatty acid content were low and within the accepted values. Fatty acids separated by gas chromatography predominating indicate the oleic and linoleic. All analyzed crude oils were of good quality, comparable to commercial and oils of wild legume seeds from the same region.

    A fin de generar información que conduzca a un uso eficiente y diversificado de los recursos naturales que ofrece el Desierto Sonorense, como es la gran variedad de plantas de la familia Leguminosae ó Fabaceae, se analizaron los aceites de las semillas: Prosopis chilensis, Prosopis velutina (mezquite, (palo azul, Cercidium praecox (palo de brea, Acacia constricta (vinorama, Acacia cymbyspina (chirahui, Acacia occidentalis (tésota, Acacia mcmurphy (tepeguaje, Desmanthus palmeri (mezquitillo, Caesalpinia caladenia (palo dorado, y Caesalpinia pumila (palo piojo. Los aceites de cada semilla fueron extraídos con hexano, se evaluaron las características fisico-químicas de calidad y la cuantificación de ácidos grasos por cromatografía de gases. El contenido de

  8. CURADO NO-ISOTERMICO DE MEZCLAS EPOXI-ACEITE DE SOJA EPOXIDADO-ANHÍDRIDO

    Directory of Open Access Journals (Sweden)

    Facundo I. Altuna

    2011-01-01

    Full Text Available Se estudió la cinética de curado no-isotérmico de mezclas de diglicidil éter de bisfenol A (DGEBA con aceite de soja epoxidado (ESO utilizando anhídrido metiltetrahidroftálico (MTHPA como agente de curado y 1-metil imidazol (1MI como iniciador. El sistema ESO/MTHPA exhibió valores de entalpía de reacción menores y temperaturas de pico exotérmico mayores que el sistema DGEBA/MTHPA debido a la menor reactividad de los grupos oxirano internos del ESO. Los parámetros cinéticos de los sistemas puros DGEBA/MTHPA y ESO/MTHPA se obtuvieron a partir de los datos calorimétricos mediante un análisis de regresión multiparamétrica utilizando un modelo cinético fenomenológico. La cinética de los sistemas puros fue utilizada para predecir la de las mezclas considerando las interacciones entre DGEBA y ESO. El modelo propuesto permitió predecir adecuadamente la cinética del proceso de curado utilizando parámetros independientes de la velocidad de calentamiento y de aplicación directa en el campo de procesamiento de estos materiales.

  9. REMEDIACIÓN DE SUELOS CONTAMINADOS CON ACEITE DE MOTOR MEDIANTE TENSIOACTIVOS ALTAMENTE BIODEGRADABLES

    Directory of Open Access Journals (Sweden)

    Ignacio Moya-Ramírez

    2014-01-01

    Full Text Available En el presente trabajo se ha estudiado el proceso de remediación de un suelo arenoso contaminado con aceite de motor, empleando dos sistemas de lavado, uno discontinuo y otro continuo. Además se evaluó la capacidad de tres surfactantes altamente biodegradables, dos sintéticos (Glucopon 600 y Findet 1214N/23 y un biosurfactante producido por Bacillus subtilis, para facilitar la eliminación del contaminante. Los resultados obtenidos con el sistema continuo fueron mejores en todos los casos a los del discontinuo, incluso con agua destilada como solución de lavado. Tanto la incorporación de los tensioactivos como el aumento de la temperatura incrementaron significativamente la remoción del contaminante en ensayos realizados con el sistema discontinuo, destacando los buenos resultados obtenidos con el biosurfactante a concentraciones próximas a la CMC. En el sistema continuo la concentración de tensioactivo no resultó tan determinante para la eliminación del contaminante , al menos por debajo de la CMC.

  10. Efecto de diferentes niveles de aceites esenciales de Lippia origanoides kunth en pollos de engorde

    Directory of Open Access Journals (Sweden)

    Liliana Betancourt L.

    2012-08-01

    Full Text Available Objetivo. Determinar el nivel de inclusión de aceite esencial de Lippia origanoides Kunth (AEO que maximice el peso corporal y la eficiencia económica. Materiales y métodos. Los AEO se obtuvieron por hidrodestilación y se analizaron por GC/MS. Se evaluaron cuatro niveles, 0, 100, 200 y 300 ppm de AEO en dos grupos de pollos; un grupo retado con ooquistes atenuados de coccidia y otro no retado. El nivel óptimo de inclusión fue estimado mediante una función sinusoidal. Resultados. La suplementación con 100 ppm de AEO redujo el impacto negativo del reto con ooquistes atenuados de coccidia sobre el peso corporal, 1.799, 1.889 y 1.995 g en los grupos retado sin AEO, retado + AEO y control, respectivamente (p<0.001. Se encontró una interacción significativa entre la suplementación con AEO y reto sobre el peso corporal y la conversión de alimento (p<0.05. El nivel de AEO que maximiza el peso corporal en los grupos de pollos no retados fue 65 ppm; mientras que para los grupos retados fue 147 ppm. Conclusiones. Se demostró que los AEO ricos en timol pueden ser un aditivo natural viable para la producción de carne de pollo.

  11. REDES DE INTERCAMBIO DE CALOR APLICADAS A LA ESTERIFICACIÓN DE ACEITES VEGETALES USADOS

    Directory of Open Access Journals (Sweden)

    María F. Laborde

    2014-01-01

    Full Text Available E n este trabajo se presenta la aplicación de redes de intercambio de calor (RIC a la esterificación de aceites vegetales usados (AVUs con catálisis ácida para la producción de biodiesel. Se aplican distintos métodos para obtener las cantidades mínimas de calor y la RIC para una capacidad de procesamiento de 0,19 kg/s de AVUs. Se considera una diferencia de temperatura mínima (∆Tmin de 10°C y los requerimientos mínimos de calentamiento y enfriamiento, resultan ser de 4629,87 W y de 10066,30 W, respectivamente. Al aplicar la red de intercambio calórico disminuye en un 78,92% el servicio de vapor requerido en el proceso y en un 62,48% el servicio de agua de enfriamiento, lo que demuestra que la integración reduce los requerimientos energéticos respecto al proceso no integrado.

  12. Transient flow combustion

    Science.gov (United States)

    Tacina, R. R.

    1984-01-01

    Non-steady combustion problems can result from engine sources such as accelerations, decelerations, nozzle adjustments, augmentor ignition, and air perturbations into and out of the compressor. Also non-steady combustion can be generated internally from combustion instability or self-induced oscillations. A premixed-prevaporized combustor would be particularly sensitive to flow transients because of its susceptability to flashback-autoignition and blowout. An experimental program, the Transient Flow Combustion Study is in progress to study the effects of air and fuel flow transients on a premixed-prevaporized combustor. Preliminary tests performed at an inlet air temperature of 600 K, a reference velocity of 30 m/s, and a pressure of 700 kPa. The airflow was reduced to 1/3 of its original value in a 40 ms ramp before flashback occurred. Ramping the airflow up has shown that blowout is more sensitive than flashback to flow transients. Blowout occurred with a 25 percent increase in airflow (at a constant fuel-air ratio) in a 20 ms ramp. Combustion resonance was found at some conditions and may be important in determining the effects of flow transients.

  13. Combustion and regulation; Combustion et reglementation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This conference was organized after the publication of the French by-law no 2010 relative to combustion installations and to the abatement of atmospheric pollution. Five topics were discussed during the conference: the new regulations, their content, innovations and modalities of application; the means of energy suppliers to face the new provisions and their schedule; the manufacturers proposals for existing installations and the new equipments; the administration control; and the impact of the new measures on exploitation and engineering. Twenty papers and 2 journal articles are reported in these proceedings. (J.S.)

  14. Combustion of drops of Mexican fuel oils with high asphaltenes content; Combustion de gotas de combustoleos mexicanos con alto contenido de asfaltenos

    Energy Technology Data Exchange (ETDEWEB)

    Garcia Rodriguez, Jose Francisco [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1998-09-01

    In this work the combustion of fuel drops with a content of 18% of asphaltenes has been studied . The results obtained for this fuel were compared with the ones obtained for another with a content of 12% asphaltenes. The drops were suspended in a platinum filament and burned in an spherical radiant furnace. The drop size varied between 600 and 800 microns. The fuel drops with 12% asphaltenes showed shorter combustion times, a smaller diameter increment of the smaller diameter during the combustion stages and also a shorter burning time of the carbonaceous residue than the fuel drops with a content of 18% asphaltenes. [Espanol] En el presente trabajo se ha estudiado la combustion de gotas de combustible con 18% de contenido de asfaltenos. Los resultados obtenidos para este combustible se compararon con los obtenidos para otro con 12% de contenido de asfaltenos. Las gotas fueron suspendidas en un filamento de platino y quemadas en un horno radiante esferico. El tamano de las gotas vario entre 600 y 800 micras. Las gotas de combustible con 12% de asfaltenos mostraron tiempos de combustion mas cortos, un incremento del diametro menor durante las etapas de combustion y un tiempo de quemado del residuo carbonoso tambien mas corto que las gotas del combustible con 18% de contenido de asfaltenos.

  15. Characterization of enzymatically extracted sunflower seed oil as well as the protein residues

    Directory of Open Access Journals (Sweden)

    Sitohy, M. Z.

    1993-12-01

    Full Text Available Sunflower seed oil was enzymatically extracted with six different enzymes: cellulase, hemicellulase, animal proteinase, acid proteinase, pectinase and pectinex under the following conditions: substrate concentration in phosphate buffer (0.5M, pH 5 30%, enzyme concentration 2% (E/S, temperature 50°C and time 3 hours. The obtained oils were analyzed for physicochemical properties and fatty acid profiles. The protein residues were analyzed for amino acid compositions. The results showed that the enzymatic extraction with cellulase or hemicellulase could maintain good oil quality of the extracted oils as their levels of linoleic and oleic acids recorded similar values to those of the control oil extracted with organic solvents. Also the level of iodine value was in the same level of control. On the other hand, the use of proteases in the enzymatic extraction of sunflower seed oil caused some reductions in the levels of the unsaturated fatty acids as well as the iodine value. The pectinases showed a similar trend to that of the proteinase with the least recovery of linoleic acid among the different oils under study. Similarly, the use of cellulases did not change the amino acid composition of the protein residue as compared to the control, in the contrary to the extraction with the proteinases which caused reduction of some amino acids from the protein residues especially lysine, leucine, iso-leucine, alanine, arginine and aspartic. In that respect the use of pectinases behaved similar to cellulases.

    Aceite de semilla de girasol fue extraído enzimáticamente con seis enzimas diferentes: celulasa, hemicelulasa, proteinasa animal, proteinase acida, pectinasa y pectinex bajo las condiciones siguientes: concentración de sustrato en tampón fosfato (0,5M, pH 5 30%, concentración enzimática 2% (E/S, temperatura 50°C y tiempo 3 horas. Los aceites obtenidos fueron analizados por sus propiedades fisicoquímicas y perfiles de ácidos grasos

  16. Residual nilpotence and residual solubility of groups

    International Nuclear Information System (INIS)

    Mikhailov, R V

    2005-01-01

    The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

  17. Combustible structural composites and methods of forming combustible structural composites

    Science.gov (United States)

    Daniels, Michael A.; Heaps, Ronald J.; Steffler, Eric D.; Swank, W. David

    2013-04-02

    Combustible structural composites and methods of forming same are disclosed. In an embodiment, a combustible structural composite includes combustible material comprising a fuel metal and a metal oxide. The fuel metal is present in the combustible material at a weight ratio from 1:9 to 1:1 of the fuel metal to the metal oxide. The fuel metal and the metal oxide are capable of exothermically reacting upon application of energy at or above a threshold value to support self-sustaining combustion of the combustible material within the combustible structural composite. Structural-reinforcing fibers are present in the composite at a weight ratio from 1:20 to 10:1 of the structural-reinforcing fibers to the combustible material. Other embodiments and aspects are disclosed.

  18. Selective leaching of coal and coal combustion solid residues

    Energy Technology Data Exchange (ETDEWEB)

    O`Keefe, C.A. [University of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center

    1996-12-31

    Selective leaching of coal and fly ash were carried out in order to predict the potential for environmental impact as well as other properties related to the aqueous solubility of inorganic constituents. Chemical fractionation can help to identify the distribution of major, minor, and trace constituents. 35 refs., 10 tabs.

  19. Optical Tomography in Combustion

    DEFF Research Database (Denmark)

    Evseev, Vadim

    spectral measurements at several line-of-sights with a view to applications for tomographic measurements on full-scale industrial combustion systems. The system was successfully applied on industrial scale for simultaneous fast exhaust gas temperature measurements in the three optical ports of the exhaust......D project, it was also important to investigate the spectral properties of major combustion species such as carbon dioxide and carbon monoxide in the infrared range at high temperatures to provide the theoretical background for the development of the optical tomography methods. The new software....... JQSRT 113 (2012) 2222, 10.1016/j.jqsrt.2012.07.015] included in the PhD thesis as an attachment. The knowledge and experience gained in the PhD project is the first important step towards introducing the advanced optical tomography methods of combustion diagnostics developed in the project to future...

  20. Internal combustion engine

    Science.gov (United States)

    Baker, Quentin A.; Mecredy, Henry E.; O'Neal, Glenn B.

    1991-01-01

    An improved engine is provided that more efficiently consumes difficult fuels such as coal slurries or powdered coal. The engine includes a precombustion chamber having a portion thereof formed by an ignition plug. The precombustion chamber is arranged so that when the piston is proximate the head, the precombustion chamber is sealed from the main cylinder or the main combustion chamber and when the piston is remote from the head, the precombustion chamber and main combustion chamber are in communication. The time for burning of fuel in the precombustion chamber can be regulated by the distance required to move the piston from the top dead center position to the position wherein the precombustion chamber and main combustion chamber are in communication.

  1. Desodorización de aceite de pescado mediante destilación a alto vacío: preservación de las características químicas del aceite

    Directory of Open Access Journals (Sweden)

    Nieto, S.

    1993-02-01

    Full Text Available The construction and the operation conditions of a high vacuum glass-equipment for deodorizing sardine oil at laboratory scale is described. The equipment working at 120°C and at a pressure of 0.05-0.1 mmHg maintains unchanged the n-3 fatty acid composition of the oil producing a considerable reduction in the cholesterol and peroxide content of the oil. The stripper, having a throughput of 1500-1800 mL/hr, allows the obtaining of a high quality fish oil suitable for experimental and for pharmacological and/or nutritional applications.

    Se describe la construcción y condiciones de operación de un destilador de vidrio de alto vacío que permite, a escala de laboratorio, la desodorización del aceite de sardina española. El equipo operando a temperaturas no superiores a 120°C y a una presión constante de 0,05-0,1 mmHg no altera la composición de ácidos grasos n-3 del aceite y permite una disminución considerable del colesterol y de los peróxidos orgánicos. La destilación permite obtener un aceite de alta calidad con un rendimiento de 1500-1800 mL/hr que puede ser utilizado para fines experimentales o para uso farmacológico y/o nutricional.

  2. Quantitative measurements of in-cylinder gas composition in a controlled auto-ignition combustion engine

    Science.gov (United States)

    Zhao, H.; Zhang, S.

    2008-01-01

    One of the most effective means to achieve controlled auto-ignition (CAI) combustion in a gasoline engine is by the residual gas trapping method. The amount of residual gas and mixture composition have significant effects on the subsequent combustion process and engine emissions. In order to obtain quantitative measurements of in-cylinder residual gas concentration and air/fuel ratio, a spontaneous Raman scattering (SRS) system has been developed recently. The optimized optical SRS setups are presented and discussed. The temperature effect on the SRS measurement is considered and a method has been developed to correct for the overestimated values due to the temperature effect. Simultaneous measurements of O2, H2O, CO2 and fuel were obtained throughout the intake, compression, combustion and expansion strokes. It shows that the SRS can provide valuable data on this process in a CAI combustion engine.

  3. Quantitative measurements of in-cylinder gas composition in a controlled auto-ignition combustion engine

    International Nuclear Information System (INIS)

    Zhao, H; Zhang, S

    2008-01-01

    One of the most effective means to achieve controlled auto-ignition (CAI) combustion in a gasoline engine is by the residual gas trapping method. The amount of residual gas and mixture composition have significant effects on the subsequent combustion process and engine emissions. In order to obtain quantitative measurements of in-cylinder residual gas concentration and air/fuel ratio, a spontaneous Raman scattering (SRS) system has been developed recently. The optimized optical SRS setups are presented and discussed. The temperature effect on the SRS measurement is considered and a method has been developed to correct for the overestimated values due to the temperature effect. Simultaneous measurements of O 2 , H 2 O, CO 2 and fuel were obtained throughout the intake, compression, combustion and expansion strokes. It shows that the SRS can provide valuable data on this process in a CAI combustion engine

  4. Fuel and combustion stratification study of Partially Premixed Combustion

    OpenAIRE

    Izadi Najafabadi, M.; Dam, N.; Somers, B.; Johansson, B.

    2016-01-01

    Relatively high levels of stratification is one of the main advantages of Partially Premixed Combustion (PPC) over the Homogeneous Charge Compression Ignition (HCCI) concept. Fuel stratification smoothens heat release and improves controllability of this kind of combustion. However, the lack of a clear definition of “fuel and combustion stratifications” is obvious in literature. Hence, it is difficult to compare stratification levels of different PPC strategies or other combustion concepts. T...

  5. Aerosols from biomass combustion

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T

    2001-07-01

    This report is the proceedings of a seminar on biomass combustion and aerosol production organised jointly by the International Energy Agency's (IEA) Task 32 on bio energy and the Swiss Federal Office of Energy (SFOE). This collection of 16 papers discusses the production of aerosols and fine particles by the burning of biomass and their effects. Expert knowledge on the environmental impact of aerosols, formation mechanisms, measurement technologies, methods of analysis and measures to be taken to reduce such emissions is presented. The seminar, visited by 50 participants from 11 countries, shows, according to the authors, that the reduction of aerosol emissions resulting from biomass combustion will remain a challenge for the future.

  6. High Gravity (g) Combustion

    Science.gov (United States)

    2006-02-01

    UNICORN (Unsteady Ignition and Combustion with Reactions) code10. Flame propagation in a tube that is 50-mm wide and 1000-mm long (similar to that...turbine engine manufacturers, estimating the primary zone space heating rate. Both combustion systems, from Company A and Company B, required a much...MBTU/atm-hr-ft3) Te m pe ra tu re R is e (K ) dP/P = 2% dP/P = 2.5% dP/P = 3% dP/P = 3.5% dP/P = 4% Company A Company B Figure 13: Heat Release Rate

  7. Alcohol combustion chemistry

    KAUST Repository

    Sarathy, Mani

    2014-10-01

    Alternative transportation fuels, preferably from renewable sources, include alcohols with up to five or even more carbon atoms. They are considered promising because they can be derived from biological matter via established and new processes. In addition, many of their physical-chemical properties are compatible with the requirements of modern engines, which make them attractive either as replacements for fossil fuels or as fuel additives. Indeed, alcohol fuels have been used since the early years of automobile production, particularly in Brazil, where ethanol has a long history of use as an automobile fuel. Recently, increasing attention has been paid to the use of non-petroleum-based fuels made from biological sources, including alcohols (predominantly ethanol), as important liquid biofuels. Today, the ethanol fuel that is offered in the market is mainly made from sugar cane or corn. Its production as a first-generation biofuel, especially in North America, has been associated with publicly discussed drawbacks, such as reduction in the food supply, need for fertilization, extensive water usage, and other ecological concerns. More environmentally friendly processes are being considered to produce alcohols from inedible plants or plant parts on wasteland. While biofuel production and its use (especially ethanol and biodiesel) in internal combustion engines have been the focus of several recent reviews, a dedicated overview and summary of research on alcohol combustion chemistry is still lacking. Besides ethanol, many linear and branched members of the alcohol family, from methanol to hexanols, have been studied, with a particular emphasis on butanols. These fuels and their combustion properties, including their ignition, flame propagation, and extinction characteristics, their pyrolysis and oxidation reactions, and their potential to produce pollutant emissions have been intensively investigated in dedicated experiments on the laboratory and the engine scale

  8. Combustibility of tetraphenylborate solids

    International Nuclear Information System (INIS)

    Walker, D.D.

    1989-01-01

    Liquid slurries expected under normal in-tank processing (ITP) operations are not ignitible because of their high water content. However, deposits of dry solids from the slurries are combustible and produce dense, black smoke when burned. The dry solids burn similarly to Styrofoam and more easily than sawdust. It is the opinion of fire hazard experts that a benzene vapor deflagration could ignite the dry solids. A tetraphenylborate solids fire will rapidly plug the waste tank HEPA ventilation filters due to the nature of the smoke produced. To prevent ignition and combustion of these solids, the waste tanks have been equipped with a nitrogen inerting system

  9. Studies in combustion dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Koszykowski, M.L. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    The goal of this program is to develop a fundamental understanding and a quantitative predictive capability in combustion modeling. A large part of the understanding of the chemistry of combustion processes comes from {open_quotes}chemical kinetic modeling.{close_quotes} However, successful modeling is not an isolated activity. It necessarily involves the integration of methods and results from several diverse disciplines and activities including theoretical chemistry, elementary reaction kinetics, fluid mechanics and computational science. Recently the authors have developed and utilized new tools for parallel processing to implement the first numerical model of a turbulent diffusion flame including a {open_quotes}full{close_quotes} chemical mechanism.

  10. CARACTERIZACIÓN DEL ACEITE DE SEMILLA DE CHÍA (Salvia hispánica L.), EXTRAÍDO CON SOLVENTE ORGÁNICO Y PRENSADO EN FRIO – LAMBAYEQUE 2014

    OpenAIRE

    Quintana Vasquez, Jheniffer del Carmen; Universidad Señor de Sipán; Valencia Liza, Jairo Wilson; Universidad Señor de Sipán

    2015-01-01

    La semilla de Chía (Salvia hispánica L.), es muy importante por su alto rendimiento de aceite (27%) y calidad, siendo la fuente vegetal con más alta concentración de omega 3 y omega 6. El proceso de producción de aceite de Chía radica en la adecuada selección del método de extracción que influyen en el rendimiento y la calidad del aceite.  En la presente investigación se evaluó el proceso de extracción de aceite de la semilla de Chía de la variedad negra y blanca. Para la extracción del aceit...

  11. Combustion stratification for naphtha from CI combustion to PPC

    NARCIS (Netherlands)

    Vallinayagam, R.; Vedharaj, S.; An, Y.; Dawood, A.; Izadi Najafabadi, M.; Somers, L.M.T.; Johansson, B.H.

    2017-01-01

    This study demonstrated the change in combustion homogeneity from conventional diesel combustion via partially premixed combustion towards HCCI. Experiments are performed in an optical diesel engine at a speed of 1200 rpm with diesel fuel. Single injection strategy is employed and the fuel is

  12. Comportamiento reológico dinámico de mayonesas comerciales: influencia de la temperatura y del contenido en aceite

    Directory of Open Access Journals (Sweden)

    Berjano, M.

    1991-10-01

    Full Text Available The linear dynamic viscoelasticity of two commercial foodstuffs, oil in water emulsions with very different oil contents, has been studied. Temperature ranged between 10 and 40°C. From the experimental results it can be deduced that less oil content produces a significant decrease in the linear viscoelastic functions, as well as an enhanced temperature sensitivity.

    Se estudia el comportamiento viscoelástico dinámico, en zona lineal, de dos productos comerciales que son emulsiones alimentarias aceite en agua, o/w, con un contenido en aceite muy distinto. El intervalo de temperatura estudiado ha variado entre 10 y 40°C. De los resultados obtenidos se deduce que un menor contenido en aceite produce una disminución significativa de todas las funciones viscoelásticas, así como una mayor influencia del efecto de la temperatura.

  13. Toxicology of Biodiesel Combustion products

    Science.gov (United States)

    1. Introduction The toxicology of combusted biodiesel is an emerging field. Much of the current knowledge about biological responses and health effects stems from studies of exposures to other fuel sources (typically petroleum diesel, gasoline, and wood) incompletely combusted. ...

  14. Novel approaches in advanced combustion characterization of fuels for advanced pressurized combustion

    Energy Technology Data Exchange (ETDEWEB)

    Aho, M.; Haemaelaeinen, J. [VTT Energy (Finland); Joutsenoja, T. [Tampere Univ. of Technology (Finland)

    1996-12-01

    This project is a part of the EU Joule 2 (extension) programme. The objective of the research of Technical Research Centre of Finland (VTT) is to produce experimental results of the effects of pressure and other important parameters on the combustion of pulverized coals and their char derivates. The results can be utilized in modelling of pressurized combustion and in planning pilot-scale reactors. The coals to be studied are Polish hvb coal, French lignite (Gardanne), German anthracite (Niederberg) and German (Goettelbom) hvb coal. The samples are combusted in an electrically heated, pressurized entrained flow reactor (PEFR), where the experimental conditions are controlled with a high precision. The particle size of the fuel can vary between 100 and 300 {mu}m. The studied things are combustion rates, temperatures and sizes of burning single coal and char particles. The latter measurements are performed with a method developed by Tampere University of Technology, Finland. In some of the experiments, mass loss and elemental composition of the char residue are studied in more details as the function of time to find out the combustion mechanism. Combustion rate of pulverized (140-180 {mu}m) Gardanne lignite and Niederberg anthracite were measured and compared with the data obtained earlier with Polish hvb coal at various pressures, gas temperatures, oxygen partial pressures and partial pressures of carbon dioxide in the second working period. In addition, particle temperatures were measured with anthracite. The experimental results were treated with multivariable partial least squares (PLS) method to find regression equation between the measured things and the experimental variables. (author)

  15. Extracción, caracterización y evaluación de la actividad antibacteriana del aceite esencial de Senecio graveolens Wedd (Wiskataya

    Directory of Open Access Journals (Sweden)

    Kiev Ochoa Pumaylle

    2012-01-01

    Full Text Available El objetivo del presente trabajo fue extraer, caracterizar y evaluar la actividad antibacteriana del aceite esencial de Senecio graveolens Wedd (Wiskataya frente a Escherichia coli y Staphylococcus aureus ATCC 29923. Las hojas y tallos se recolectaron a una altitud de 3800 m.s.n.m. en el distrito de Puquio, provincia de Lucanas, departamento de Ayacucho. El aceite esencial se obtuvo por destilación por arrastre con vapor de agua, a partir de las hojas y tallos desecados de S. graveolens, con rendimiento de 1,26 % (p/p. La muestra extraída fue caracterizada a través de ensayos físicos. La composición química del aceite se evaluó mediante cromatografía de gas con detector de masa (CG-SM. La actividad antibacteriana del aceite de S. graveolens se realizó por el método de difusión en agar en pocillos, utilizando cepas de microorganismos gram positivo como S. aureus y gram negativo como E. coli. La densidad del producto resultó 0,8755 g/ml a 20 ºC; índice de refracción 1,4726; índice de rotación 102°85’ y soluble en etanol; el cromatograma mostró componentes mayoritarios con un contenido de 52,39 % Sabineno, 8,20 % (+-4-careno, 7,11 % τ-terpineno, 6,74 % β-myrceno, 3,78 % 4-terpinenol, 3,67 % Pulegona. Los resultados mostraron actividad antibacteriana marcada y moderada, para S. aureus y E. coli, respectivamente, observándose formación de halos de inhibición para concentraciones del aceite esencial a 80, 90 y 100 %. El aceite esencial de S. graveolens se presenta con actividad antibacteriana promisoria.

  16. Copolymers of new generation for the dehydrated crude oil (petroleum); Copolimeros de nueva generacion para el deshidratado de aceite crudo (petroleo)

    Energy Technology Data Exchange (ETDEWEB)

    Castro Sotelo, Laura Veronica [Instituto Politecnico Nacional ESIQIE, Mexico, D.F. (Mexico)]. E-mail: lcastros@ipn.mx; Flores Oropeza, Eugenio Alejandro; Hernandez Cortez, Jose Gonzalo; Lopez Ortega, Alfonso; Arreguin Valencia, Felipe [Instituto Mexicano del Petroleo, Mexico, D.F. (Mexico)]. E-mail: eaflores@imp.mx; jhcortez@imp.mx; alopezo@imp.mx; flos2099@yahoo.com.mx; Hernandez Garcia, Arnulfo [Universidad Nacional Autonoma de Mexico, Facultad de Quimica, Mexico, D.F. (Mexico)]. E-mail: arte8080@hotmail.com; Hernandez Xilohua, Arturo Eutiquio [Instituto Mexicano del Petroleo Mexico, D.F. (Mexico)]. E-mail: art_eut@hotmail.com; Ramirez Gutierrez, David; Hernandez Carbajal, Edgar Ivan [Instituto Politecnico Nacional, ESIQIE, Mexico, D.F. (Mexico)]. Email: theprettiestthingever@hotmail.com; hcei11@hotmail.com; Vazquez Moreno, Flavio Salvador [Instituto Mexicano del Petroleo, Mexico, D.F. (Mexico)]. E-mail: flaviusmx@yahoo.com.mx

    2010-11-15

    Crude oil is a mixture of hydrocarbons, salts and water as impurities. When crude oil has high water content, their commercial value is reduced in the market, so the separation of these impurities is important for a better quality product. The content of these impurities in the crude oil reduction is a concern across the world. There are several methods for crude oil dehydration and breaking emulsions; this work presents the results of tests demulsifiers, agents which are different molecular mass polyethers. Using several test bottles compared performance agents demulsifiers which were assessed at different concentrations in a heavy crude oil from wells in the southeast of Mexico. The evaluation results showed the range of molecular mass of polymers that provide better performance for the abatement of the water content in the crude oil. [Spanish] El aceite crudo es una mezcla de hidrocarburos, sales y agua como impurezas. Cuando el aceite crudo presenta alto contenido de agua, su valor a nivel comercial se reduce en el mercado, por lo que es importante la separacion de estas impurezas para obtener un producto de mejor calidad. La reduccion del contenido de estas impurezas en el aceite crudo es una preocupacion a nivel mundial. Existen varios metodos para la deshidratacion del aceite crudo y romper las emulsiones; en este trabajo se presentan los resultados de pruebas con agentes desemulsificantes, los cuales son polieteres de diferente masa molecular. Mediante varias pruebas de botellas se comparo el desempeno de los agentes desemulsificantes los cuales fueron evaluados a diferentes concentraciones en un aceite crudo pesado procedente de pozos del Sureste de Mexico. Los resultados de la evaluacion mostraron el intervalo de masa molecular de los polimeros que proporcionan un mejor desempeno en el abatimiento del contenido de agua en el aceite crudo.

  17. Diagramas de equilibrio para la extracción con solvente de aceite e insecticida de semilla molida de nim

    Directory of Open Access Journals (Sweden)

    R. Espinosa

    2006-01-01

    Full Text Available En este trabajo se construyeron diagramas de equilibrio para la extracción con hexano de aceite de la semilla molida de nim (GNSK y de la extracción posterior con etanol de insecticida de la GNSK sin aceite. Los datos experimentales fueron obtenidos a diferentes temperaturas, poniendo en contacto sólido y solvente en diferentes proporciones en frascos Erlenmeyer. Se suministró agitación y se mantuvo la temperatura controlada hasta alcanzar el equilibrio. La composición del extracto y del refinado se determinó separando los solventes por evaporación. Se propone ecuaciones para la curva de refinado y la curva de distribución. En ambas extracciones, la fracción de solución retenida dentro de la estructura celular del sólido molido aumenta con la temperatura. La concentración del extracto tiene más influencia en la cantidad de solución retenida para la extracción de insecticida que para la extracción de aceite. Para extractos diluidos, la concentración de soluto tiende a ser mayor en el extracto que en la solución retenida. Esta tendencia es más pronunciada cuando la temperatura aumenta. A temperaturas cercanas al punto de ebullición, hay mayor tendencia a la retención de solvente por el sólido, a cualquier concentración.

  18. Composición y propiedades antibacterianas del aceite esencial de Lippia alba (Mill. n. e. Brown

    Directory of Open Access Journals (Sweden)

    Jorge A Pino Alea

    1996-04-01

    Full Text Available Con ayuda de la cromatografía gaseosa capilar, espectrometría de masas y espectroscopia infrarroja, se estudiaron los componentes volátiles del aceite esencial de Lippia alba (Mill. N. E. Br., lográndose identificar 43 compuestos, de los cuales 20 se informan por primera vez. Se encontró un alto contenido de carvona que hace suponer que se está en presencia de un nuevo quimiotipo. Se evaluó la actividad antibacteriana del aceite esencial sobre una bacteria integrada por 9 especies de bacterias, mediante la determinación de las concentraciones mínimas inhibitorias y con el empleo del método de las diluciones seriadas dobles en medio líquido. El aceite presentó actividad antibacteriana, siendo mayor en general, sobre los gérmenes grampositivos, con valores de las concentraciones mínimas inhibitorias entre 0,3 y 0,63 mg/mL.With the aid of capillary gas chromatography, mass spectrometry, and infrared spectroscopy, the volatile components of Lippia alba (Mill. N.E. Br. essential oil, were studied, achieving the identification of 43 compounds, 20 of them reported for the first time. A high contents of carvone (carvona was found, and this suggests the presence of a new chemotype. The antibacterial activity of the essential oil on a bacteria integrated by 9 bacterial species, was valuated by determining the inhibitory minimal concentrations, and with the use of the method of double dilution series in a liquid medium. The oil presented antibacterial activity, generally being higher on gram-positive germs, with values of the inhibitory minimal concentrations between 0,3 and 0,63 mg/L.

  19. Influencia de la producción integrada del olivar sobre la calidad del aceite de oliva virgen

    Directory of Open Access Journals (Sweden)

    Gutiérrez-Rosales, F.

    2006-12-01

    Full Text Available A study has been conducted to determine the influence of integrated olive production on the quality of extra virgin olive oil. On two different dates, samples from three different holdings were taken in integrated production (I parcels, and in conventional production (C parcels, both adjacent. The analytical determinations were free acidity, peroxide value, K232 and K270, fatty acid composition, esterols, phenolic compounds, tocopherols, stability to oxidation and sensory analysis. Most interesting among the results obtained were total contents of esterols and tocopherols, higher in olive oils of integrated production.Se ha realizado un estudio para ver la influencia de la producción integrada del olivar sobre la calidad del aceite de oliva virgen. Se tomaron muestras de aceitunas de tres fincas distintas, en parcelas correspondientes a olivar de secano, de producción integrada (I, y en parcelas adyacentes a estas de producción convencional (C, en dos fechas diferentes. Las determinaciones analíticas realizadas han sido acidez libre, índice de peróxidos, K232 y K270, composición de ácidos grasos, esteroles, compuestos fenólicos, tocoferoles, estabilidad oxidativa y análisis sensorial. En los resultados obtenidos destaca que los valores más altos de esteroles totales y tocoferoles corresponden a los aceites de producción integrada. Así mismo, los aceites de producción convencional presentan mayor contenido de fenoles totales y parecen ofrecer mayor estabilidad.

  20. Estudio de la composición química de las semillas y aceites seminales de Ligustrum lucidum Ait y Ligustrum sinense Lour

    Directory of Open Access Journals (Sweden)

    Nolasco, S. M.

    2001-02-01

    Full Text Available The fruits of Ligustrum lucidum Ait and Ligustrum sinense Lour were harvested in Olavarria (Province of Buenos Aires, Argentine. The seeds and extracted oils were analysed for characteristics and composition. The seed contained 8,7-10 and 10,7 % (dry basis, respectively. The physicochemical characteristics of the crude oils were: refractive index 1,4647 and 1,4640 (at 25ºC, iodine value 93,7 and 88,8, saponification index 167 and 154, unsaponifiable matter 11 and 18 %, and free fatty acid content of 4,8 and 9,2 (mg KOH/g, respectively. Gas chromatographic analysis of the oils revealed high levels of oleic acid (57,8 and 51,10%, about 25,1 and 29,6 % of saturated acids, respectively, most of them consisting of palmitic acid, but they have a significant content of acid of more than 18 atoms of carbon. The residual seed meals contained low level of crude protein and of available lysine (2.45, 3.65, g/16g N, respectively. Total and phytic acid phosphorous, calcium, ash, crude fiber, and polysaccharides (non presence of starch contents are reported.Frutos de Ligustrum lucidum Ait y Ligustrum sinense Lour fueron cosechados en Olavarría (provincia de Buenos Aires, Argentina y sus semillas separadas en forma manual. Las semillas se agotaron con n-hexano, obteniendo los aceites crudos con rendimientos del 8,7-10% y 10,7 % (base seca, respectivamente. Los aceites crudos se examinaron en sus características fisicoquímicas (Índice de refracción: 1,4647 y 1,4640 (a 25ºC, Indice de iodo: 93,7 y 88,8, Indice de saponificación: 167 y 154, insaponificable: 11 y 18 %, Indice de acidez: 4,8 y 9,2 (mgKOH/g respectivamente. El análisis por cromatografía gaseosa de los ésteres metílicos reveló alto porcentaje de ácido oleico (57,8 y 51,1%, alrededor de un 25,1 y 29,6 % de ácidos saturados, respectivamente, predominando el ácido palmítico, pero con un significativo contenido de ácidos de más de 18 átomos de carbono. Las harinas residuales de

  1. Underground treatment of combustible minerals

    Energy Technology Data Exchange (ETDEWEB)

    Sarapuu, E

    1954-10-14

    A process is described for treating oil underground, consisting in introducing several electrodes spaced one from the other in a bed of combustibles underground so that they come in electric contact with this bed of combustibles remaining insulated from the ground, and applying to the electrodes a voltage sufficient to produce an electric current across the bed of combustibles, so as to heat it and create an electric connection between the electrodes on traversing the bed of combustibles.

  2. Frutales y agroindustria: conservas, aceites y maderas (Chile y Cuyo, 1550-1850

    Directory of Open Access Journals (Sweden)

    Lacoste, Pablo

    2011-12-01

    Full Text Available The rapid propagation of European fruit-bearing plants in Chile and Cuyo led to the problem of their exploitation, which was a complex issue in the period before the availability of means of refrigeration. The response was to encourage agro-industrial activity. Some fruits were conserved through a process of dehydration and others were used in the making of oils. Some of these products were commercialised on the domestic market and others were exported, especially to Peru. There was also an improved use of the timber from fruit trees in both the construction industry and carpentry and cabinet-making. These activities ensured the economic viability of fruit-growing and made it possible for it to expand in the region under analysis.

    La rápida propagación de plantas frutales europeas en Chile y Cuyo formuló el problema de su aprovechamiento, asunto complejo antes de la disponibilidad de medios de refrigeración. La respuesta fue el impulso a la actividad agroindustrial. Algunos frutas se conservaban mediante deshidratación, otras se usaban para elaboraban aceites. Algunos de estos productos se comercializaban en el mercado interno y otros se exportaban, particularmente al Perú. Además se avanzó en el aprovechamiento de frutales tanto para construcción como en carpintería y ebanistería. Estas actividades aseguraron la viabilidad económica de la fruticultura e hicieron posible su expansión en la región estudiada.

  3. Metabolismo de carbohidratos en palmas de aceite (Elaeis guineensis Jacq. afectadas por marchitez letal

    Directory of Open Access Journals (Sweden)

    Pèrez Angela Patricia

    2010-08-01

    Full Text Available La enfermedad conocida como “marchitez letal” se presenta
    en plantaciones de la zona baja del río Upía, en palmas de siete
    años de sembradas. No se conoce el posible agente causal o
    factores que predisponen a las palmas a la enfermedad, y no se
    ha registrado hasta la fecha en otras zonas palmeras del país. Se
    analizó el metabolismo de carbohidratos en palmas de aceite
    con síntomas iniciales de la enfermedad, palmas sospechosas
    de presentar la enfermedad y palmas sanas dentro y fuera de
    un foco. Se tomaron muestras de hojas, raíces y estípite para
    determinar las concentraciones de almidón, azúcares reductores,
    no reductores y totales. La concentración de azúcares
    reductores tuvo un incremento en las palmas con síntomas
    iniciales y sospechosos; los azúcares totales presentaron mayor
    concentración en las palmas sospechosas de tener la enfermedad
    con respecto a las palmas con síntomas iniciales. Los azúcares
    no reductores en los diferentes órganos evaluados tuvieron
    una concentración muy baja. Los resultados observados en la
    alteración del metabolismo de los carbohidratos en las palmas
    enfermas probablemente sugieren que los fitoplasmas estén
    asociados a la enfermedad.

  4. Mezclas binarias y ternarias del aceite y grasa hidrogenada de la castaña de Brasil (Bertholletia excelsa

    Directory of Open Access Journals (Sweden)

    Polakiewicz, Bronislaw

    2000-12-01

    Full Text Available Crude Brazilian nut oil was hydrogenated at 175ºC, 3 atm., 60 minutes (GH1, and 150ºC, 1 atm., 30 minutes (GH2, and with this products and the crude oil were prepared ternary blends. Fatty acids demonstrated the increase of stearic acid from 11.6% of crude oil to 56.7% in GH1 and 16.3% in GH2. In the blends, were determined the yield point, solid fat content, melting point and viscosity, for this blends were applied a special model of multiple regression. Results showed that the estimated properties were not dependent on the three components interactions. In general, the significant interactions, blends crude oil/GH1 and GH1/GH2, showed an antagonic, effect to consistency and solid fat content, typical of eutectic interactions of fats. The interactions were not significative for melting point and viscosity at 60ºC, attesting a perfect mixing model.El aceite de castaña de Brasil crudo se sometió a dos hidrogenaciones, a 175ºC, 3 atm, 60 minutos (GH1, y a 150ºC, 1 atm., 30 minutos (GH2, y con los productos de éstas, y el aceite original, se prepararon mezclas binarias y ternarias. Se incrementó la concentración del ácido esteárico de 11.6% del aceite original a 56.7% en GH1 y a 16.3% en GH2. Se realizaron los análisis de consistencia, contenido de grasa sólida, punto de fusión y viscosidad, y sobre estos parámetros se aplicó un modelo de regresión múltiple. Los resultados indicaron que las propiedades estimadas no dependían de las interacciones de los tres componentes. Las interacciones fueron significativas para las mezclas de aceite bruto/GH1 y GH1/GH2, demostrando efecto antagónico para la consistencia y contenido de grasa sólida. Las interacciones no fueron significativas para el punto de fusión y viscosidad a 60ºC, demostrando un modelo perfecto de mezcla.

  5. CONSERVACIÓN MICROBIOLÓGICA DE EMBUTIDO CARNICO ARTESANAL CON ACEITES ESENCIALES Eugenia caryophyllata Y Thymus vulgaris

    OpenAIRE

    TOFIÑO-RIVERA, ADRIANA; ORTEGA-CUADROS, MAILEN; HERRERA-HINOJOSA, BELKIS KATINA; FRAGOSO-CASTILLA, PEDRO; PEDRAZA-CLAROS, BERTILDA

    2017-01-01

    RESUMEN Las demandas del sector cárnico y sus derivados en Colombia, justifican la importancia de encontrar aditivos que mantengan las propiedades nutritivas del alimento con menor o nula inclusión de químicos adversos a la salud. Se evaluó la calidad microbiológica y características sensoriales de chorizos artesanales conservados con aceites esenciales de T. vulgaris y E. caryophyllata en el Departamento del Cesar. La metodología incluyó extracción, caracterización físico-química y organolép...

  6. Potencial terapéutico del aceite esencial de Chenopodium ambrosioides y algunos de sus componentes frente a Leishmania

    OpenAIRE

    Monzote Fidalgo, Lianet

    2010-01-01

    La leishmaniosis es una enfermedad causada por parásitos protozoos del género Leishmania, clasificada por la Organización Mundial de la Salud como una de las infecciones tropicales más importantes. Los fármacos disponibles son tóxicos, costosos y la resistencia parasitaria ha emergido. En las áreas endémicas la población depende fundamentalmente de la medicina natural para el tratamiento de la leishmaniosis. En este trabajo, se evaluó la actividad del aceite esencial extraído de Chenopodium a...

  7. Viabilidad financiera para la creación de una empresa productora y exportadora de aceite de jojoba.

    OpenAIRE

    Cornejo Guerra, Félix Efraín

    2015-01-01

    En el Ecuador existen zonas con climas áridos y semiáridos, propicias para el cultivo de productos que no son de uso masivo, sin embargo representan grandes oportunidades comerciales por sus propiedades fisiológicas y químicas. Uno de los productos al cual hacemos referencia es al aceite de jojoba, un producto extraído por medio de la prensa de la semilla de la planta del mismo nombre. La jojoba ( Simmondsia chinensis ) es un arbusto de hoja que es nativo de las zonas áridas calientes del nor...

  8. Aplicaciones de la agricultura de precisión en palma de aceite "Elaeis Guineensis" e hibrido O x G

    OpenAIRE

    Lizarazo Salcedo, Iván Alberto; Alfonso Carvajal, Oscar Alberto

    2011-01-01

    La agricultura de precisión está basada en el reconocimiento de la variabilidad espacial y temporal del clima, los suelos y los cultivos, y consecuentemente, de la importancia de proporcionar un manejo agronómico específico que tenga en cuenta esas diferencias. En este artículo se describe la perspectiva y los conceptos de agricultura de precisión que se están desarrollando en el sector de la palma de aceite en Colombia. En particular, se presentan dos aplicaciones que resuelven las limitacio...

  9. Caracterización fisicoquímica de los aceites crudos de algunas semillas de leguminosas del desierto sonorense

    Directory of Open Access Journals (Sweden)

    Ortega-Nieblas, M.

    1995-02-01

    Full Text Available The Sonoran desert has a great variety of nutritional native plants, mainly from the leguminous family. Although in ancient times their products were used as food by native Americans, there is little information about their potential as a food source. For this reason, oils from the following seeds were studied: Acacia famesiana (huizache, Mimosa grahamii (gatuña, Cercidium microphyilium (palo verde 1, Cercidium sonorae (brea, Parkinsonia aculeata (palo verde 2, Olneya Tesota (palo fierro and Prosopis juliflora (mezquite.
    Oils were extracted from the seeds with hexane, and contents ranged from 8.5 to 23.5 %. The physicochemical studies showed mostly unsaturated oils, as demonstrated by the iodine index, (101-147 units. Indexes of acidity, peroxides and free fatty acids were low and within the accepted values. Fatty acids were separated and quantified by gas chromatography. Linoleic and oleic acids were found to predominate. All extracted crude oils were of good quality, comparable to those from soybean, com, sunflower and carthamus.

    El desierto de Sonora cuenta con una gran variedad de plantas silvestres principalmente de la familia leguminosae de las cuales se tiene poca información acerca de su potencial como fuente nutricional. Por lo que se estudiaron los aceites de las semillas: Acacia famesiana (huizache, Mimosa grahamii (gatuña, Cercidium microphyilium (palo verde 1, Cercidium sonorae (brea, Parkinsonia aculeata (palo verde 2, Olneya Tesota (palo fierro y Prosopis juliflora (mezquite.
    Los aceites de cada semilla se extrajeron con hexano, obteniéndose de 8.5 a 23.5 %. Estos mostraron un alto grado de insaturación reflejado en los índices de lodo, de 101 a 147. Los índices de acidez, peróxidos y ácidos grasos libres fueron bajos y dentro de los valores aceptables. Al cuantificar los ácidos grasos por

  10. Diseño y fabricación de embutidos escaldados sustituyendo grasa porcina por aceite de soya

    OpenAIRE

    Vargas Vallejos, Calixto Evaristo

    2017-01-01

    Incorpora aceite de soya en sustitución de la grasa porcina en la formulación de dos tipos de embutidos: jamonada y hot dog. La metodología de la elaboración, proceso tecnológico y evaluación comprendió: el desarrollo de formulaciones estándares convencionales aceptadas por el IFT (Instituto de Tecnólogos de Alimentos) evaluaciones físicoquímicas mediante la caracterización química, incluyendo perfil de ácidos grasos (usando métodos oficiales de la AOAC), pruebas de aceptabilidad empleando pr...

  11. Transesterificación de aceite de higuerilla crudo utilizando catalizadores heterogéneos- estudio preliminar

    OpenAIRE

    Hincapié Triviño, Gina Marcela; Moreno Lopera, Jorge Andrés; López López, Diana Patricia

    2011-01-01

    Se estudió la producción de biodiesel mediante transesterificación de aceite de higuerilla crudo con etanol y metanol usando catalizadores heterogéneos. Los catalizadores utilizados fueron el óxido de calcio, carbonato de sodio y de potasio y un silicato de zinc con estructura tipo hemimorfita. La formación de alquil-ésteres fue cuantificada mediante cromatografía de gases. Las mayores conversiones fueron obtenidas con carbonato de potasio en etanol y con la hemimorfita en metanol a una conce...

  12. Caracterización y variabilidad química de dos aceites esenciales de Croton funckianus (Euphorbiaceae)

    OpenAIRE

    Coy Barrera, C. A; Gómez, D. C

    2015-01-01

    Para caracterizar químicamente el aceite esencial obtenido tanto de hojas como de frutos de dos muestras de la especie Croton funckianus, colectadas en dos sitios diferentes (Fusagasugá y Bogotá), se realizó el análisis cromatográfico por la técnica de cromatografía de gases acoplada a espectrometría de masas (CG-EM), y posteriormente se compararon los perfiles obtenidos, determinando algunas diferencias para el caso de las hojas y un alto porcentaje de similitudes para el caso de los frutos....

  13. Supersonic Combustion Ramjet Research

    Science.gov (United States)

    2012-08-01

    was in collaboration with Prof. R. Bowersox (Texas A&M University) and Dr. K. Kobayashi ( Japanese Aerospace Exploration Agency, JAXA). 4.2 Ignition... cinema stereoscopic PIV system for the measurement of micro- and meso-scale turbulent premixed flame dynamics,” Paper B13, 5th US Combustion

  14. Infrared monitoring of combustion

    International Nuclear Information System (INIS)

    Bates, S.C.; Morrison, P.W. Jr.; Solomon, P.R.

    1991-01-01

    In this paper, the use of Fourier Transform Infrared (FT-IR) spectroscopy for combustion monitoring is described. A combination of emission, transmission, and reflection FT-IR spectroscopy yields data on the temperature and composition of the gases, surfaces and suspended particles in the combustion environment. Detection sensitivity of such trace exhaust gases as CO, CO 2 , SO 2 , NO x , and unburned hydrocarbons is at the ppm level. Tomographic reconstruction converts line-of-sight measurements into spatially resolved temperature and concentration data. Examples from various combustion processes are used to demonstrate the capabilities of the technique. Industrial measurements are described that have been performed directly in the combustion zone and in the exhaust duct of a large chemical recovery boiler. Other measurements of hot slag show how FT-IR spectroscopy can determine the temperature and optical properties of surfaces. In addition, experiments with water droplets show that transmission FT-IR data yield spectra that characterize particle size and number density

  15. Combustible dust tests

    Science.gov (United States)

    The sugar dust explosion in Georgia on February 7, 2008 killed 14 workers and injured many others (OSHA, 2009). As a consequence of this explosion, OSHA revised its Combustible Dust National Emphasis (NEP) program. The NEP targets 64 industries with more than 1,000 inspections and has found more tha...

  16. Procedimiento de obtención de materailes multifuncionales y renovables a partir del rechazo de pipa procedente de la producción de aceite de girasol

    OpenAIRE

    Martín-Luengo, María Ángeles; Yates Buxcey, Malcolm; Ramos, M.; Sáez Rojo, Eduardo; González Gil, Lorena; Martínez Serrano, Ana María; Martín-Aranda, Rosa María; Sanz Lázaro, Jesús

    2011-01-01

    Procedimiento de obtención de materiales multifuncionales y renovables a partir del rechazo de pipa procedente de la producción de aceite de girasol. La presente invención se refiere al procedimiento de obtención de materiales renovables, a partir de residuos precedentes de la fabricación de aceite de girasol, para su uso como matrices biocompatibles en ingeniería de tejidos, administración controlada de sustancias de interés biológico (drogas, proteínas, genes, etc...

  17. ACTIVIDAD INSECTICIDA DE ACEITES ESENCIALES DE DOS ESPECIES DE Eucalyptus SOBRE Rhyzopertha dominica Y SU EFECTO EN ENZIMAS DIGESTIVAS DE PROGENIES

    Directory of Open Access Journals (Sweden)

    Ramiro Reyes-Guzmán

    2012-01-01

    proteolítica de las progenies; sin embargo, solamente E. globulus ocasionó la muerte de éstas (P < 0.05. Al incrementar el volumen de aceite de E. camadulensis, la actividad proteolítica del insecto aumentó, incluso al mayor tiempo de exposición. Los resultados de este estudio muestran que la fracción volátil de los aceites esenciales de eucalipto, especialmente la de E. globulus, es un agente insecticida efectivo para el control de R. dominica en trigo almacenado.

  18. Gemfibrozilo versus aceite de Sacha Inchi en la reducción de niveles de triglicéridos séricos en Rattus rattus var albinus

    OpenAIRE

    Vicuña Ríos, Augusto; Izquierdo Henríquez, Elva Julieta; Huamán Saavedra, Juan Jorge

    2012-01-01

    Objetivo: Comparar efectos hipotrigliceridemiantes entre gemfibrozilo y aceite de Sacha Inchi en Rattus rattus var albinus. Materiales y Método: Se utilizaron 36 especímenes, los cuales fueron divididos al azar en 2 grupos experimentales (GE1 y GE2) y un grupo control (GC). Fueron sometidos a etapa de acondicionamiento por 2 semanas, luego alimentación rica en grasa por 2 semanas; posteriormente se administró aceite de Sacha Inchi y gemfibrozilo a GE1 y GE2, respectivamente. Se midieron los n...

  19. Efecto del aceite esencial de Cymbopogon citratus (DC.) stapf “hierba luisa” en los niveles de ansiedad de estudiantes de educación secundaria

    OpenAIRE

    Soto Vásquez, Marilú Roxana; Universidad Nacional de Trujillo; Alvarado García, Paúl Alan Arkin; Rosales Cerquin, Luis Enrique; Cerna Castillo, José

    2017-01-01

    El objetivo de la investigación fué evaluar el efecto del aceite esencial de Cymbopogon citratus (DC.) Stapf “hierba luisa” en los niveles de ansiedad de estudiantes del quinto grado de educación secundaria de una institución educativa pública. Se realizó un estudio cuasiexperimental, pretest y postest, con una muestra de 54 alumnos, divididos en un grupo experimental tratado con aromaterapia del aceite esencial estudiado, vía inhalatoria, y un grupo control, al cual no se le aplicó ningún es...

  20. Diseño del proceso para la producción de 60 toneladas de biodiesel a partir de aceite de palma refinado

    OpenAIRE

    Castillo Gonzalez, Aracely Del Carmen; Martinez Lozano, Ernesto Rolando

    2009-01-01

    Este trabajo consiste en el diseño del Proceso para la Producción de Biodiesel a partir de Aceite de Palma Refinado, que tiene como finalidad establecer los requerimientos de máquinas y equipos, y los parámetros de operación para el funcionamiento de una planta piloto para la elaboración industrial de biodiesel aprovechando la producción de aceite de palma refinado como materia prima para el proceso. La metodología empleada en el presente trabajo está sustentada en la investigación científ...

  1. Evaluación del proceso de extracción de aceite de aguacate hass (Persea americana Mill) utilizando tratamiento enzimático

    OpenAIRE

    Buelvas Salgado, G. A; Patiño Gómez, J. H; Cano-Salazar, J. A

    2012-01-01

    Introducción. El aceite de aguacate es rico en vitaminas A, B, C y E, y está compuesto mayoritariamente por ácidos grasos monoinsaturados los cuales reducen de manera efectiva el nivel de colesterol en la sangre, ayudando en la prevención de enfermedades cardiovasculares. Objetivo. Evaluar el rendimiento de extracción de aceite de aguacate Hass (Persea americana Mill) en estado E3-M (maduro) procedente del Oriente Antioqueño, empleando complejos enzimáticos comerciales. Materiales y métodos. ...

  2. Utilización de un desecho agroindustrial proveniente de una empresa refinadora de aceite comestible para la producción de jabones

    OpenAIRE

    Altomare, Vanessa; Fernández, Celeste; Ros, Mario

    2008-01-01

    La presente investigación esta enmarcada en el diseño de un proceso técnico factible a escala industrial para la reutilización, de las arcillas blanqueadoras agotadas, que se generan como residuos del proceso de elaboración de aceite comestible a partir de semillas oleaginosas, para obtener un producto de mayor valor agregado. La caracterización de las arcillas así como la síntesis del jabón de tocador se llevó a cabo a nivel de laboratorio, obteniéndose un contenido de aceite de palma de (58...

  3. Low emission internal combustion engine

    Science.gov (United States)

    Karaba, Albert M.

    1979-01-01

    A low emission, internal combustion compression ignition engine having a cylinder, a piston movable in the cylinder and a pre-combustion chamber communicating with the cylinder near the top thereof and in which low emissions of NO.sub.x are achieved by constructing the pre-combustion chamber to have a volume of between 70% and 85% of the combined pre-chamber and main combustion chamber volume when the piston is at top dead center and by variably controlling the initiation of fuel injection into the pre-combustion chamber.

  4. Hydrogen assisted diesel combustion

    Energy Technology Data Exchange (ETDEWEB)

    Lilik, Gregory K.; Boehman, Andre L. [The EMS Energy Institute, The Pennsylvania State University, University Park, PA 16802 (United States); Zhang, Hedan; Haworth, Daniel C. [Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, PA 16802 (United States); Herreros, Jose Martin [Escuela Tecnica Superior de Ingenieros Industriales, Universidad de Castilla La-Mancha, Avda. Camilo Jose Cela s/n, 13071 Ciudad Real (Spain)

    2010-05-15

    Hydrogen assisted diesel combustion was investigated on a DDC/VM Motori 2.5L, 4-cylinder, turbocharged, common rail, direct injection light-duty diesel engine, with a focus on exhaust emissions. Hydrogen was substituted for diesel fuel on an energy basis of 0%, 2.5%, 5%, 7.5%, 10% and 15% by aspiration of hydrogen into the engine's intake air. Four speed and load conditions were investigated (1800 rpm at 25% and 75% of maximum output and 3600 rpm at 25% and 75% of maximum output). A significant retarding of injection timing by the engine's electronic control unit (ECU) was observed during the increased aspiration of hydrogen. The retarding of injection timing resulted in significant NO{sub X} emission reductions, however, the same emission reductions were achieved without aspirated hydrogen by manually retarding the injection timing. Subsequently, hydrogen assisted diesel combustion was examined, with the pilot and main injection timings locked, to study the effects caused directly by hydrogen addition. Hydrogen assisted diesel combustion resulted in a modest increase of NO{sub X} emissions and a shift in NO/NO{sub 2} ratio in which NO emissions decreased and NO{sub 2} emissions increased, with NO{sub 2} becoming the dominant NO{sub X} component in some combustion modes. Computational fluid dynamics analysis (CFD) of the hydrogen assisted diesel combustion process captured this trend and reproduced the experimentally observed trends of hydrogen's effect on the composition of NO{sub X} for some operating conditions. A model that explicitly accounts for turbulence-chemistry interactions using a transported probability density function (PDF) method was better able to reproduce the experimental trends, compared to a model that ignores the influence of turbulent fluctuations on mean chemical production rates, although the importance of the fluctuations is not as strong as has been reported in some other recent modeling studies. The CFD results confirm

  5. Optimization of heat-liberating batches for ash residue stabilization

    International Nuclear Information System (INIS)

    Karlina, O.K.; Varlackova, G.A.; Ojovan, M.I.; Tivansky, V.M.; Dmitriev, S.A.

    1999-01-01

    The ash residue obtained after incineration of solid radioactive waste is a dusting poly-dispersed powder like material that contains radioactive nuclides ( 137 Cs, 90 Sr, 239 Pu, hor ( ellipsis)). Specific radioactivity of the ash can be about 10 5 --10 7 Bq/kg. In order to dispose of the ash, residue shall be stabilized by producing a monolith material. The ash residue can be either vitrified or stabilized into a ceramic matrix. For this purpose the ash residue is mixed with fluxing agents followed by melting of obtained composition in the different type melters. As a rule this requires both significant energy consumption and complex melting equipment. A stabilization technology of ash residue was proposed recently by using heat liberating batches-compositions with redox properties. The ash residue is melted due to exothermic chemical reactions in the mixture with heat-liberating batch that occur with considerable release of heat. Stabilization method has three stages: (1) preparation of a mixture of heating batch and ash residue with or without glass forming batch (frit); (2) ignition and combustion of mixed composition; (3) cooling (quenching) of obtained vitreous material. Combustion of mixed composition occurs in the form of propagation of reacting wave. The heat released during exothermic chemical reactions provides melting of ash residue components and production of glass-like phase. The final product consists of a glass like matrix with embedded crystalline inclusions of infusible ash residue components

  6. EVALUACIÓN DE LA ACTIVIDAD ANTIBACTERIANA IN VITRO DE ACEITES ESENCIALES CONTRA Clavibacter michiganensis subespecie michiganensis

    Directory of Open Access Journals (Sweden)

    J. Borboa-Flores

    2010-02-01

    Full Text Available Las plantas producen compuestos con propiedades antimicrobianas que pueden ser empleados en el combate de diferentes enfermedades en la producción de hortalizas. Con la finalidad de buscar alternativas naturales para el control de la bacteria Clavibacter michiganensis subespecie michiganensis, se evaluó la actividad antibacteriana in vitro de 19 aceites esenciales, de los cuales fueron seleccionados 6 por su actividad bactericida. La técnica utilizada para el análisis de la actividad  antimicrobiana fue la de difusión en agar, utilizando discos de papel filtro estériles embebidos con el aceite esencial, diluidos 1:1, 1:5 y 1:10 (v/v, en medio de cultivo específico (NBY previamente inoculado con la cepa de estudio. El análisis de varianza mostró que existe diferencia significativa (p

  7. Técnicas de aislamiento y concentración de volátiles de aceites vegetales

    Directory of Open Access Journals (Sweden)

    Morales, M. T.

    1992-06-01

    Full Text Available One of the methods for food flavor evaluation is the analysis of volatile components. First step in this kind of analysis Is the isolation and concentration of volatiles. A review is carried out about different techniques applied in foods and especially in vegetable oils. Very different methods have been used, an explication of each one with its different cases are presented. Likewise the applications carried out in vegetable oils during last years are discussed.

    Uno de los métodos de evaluación del flavor de los alimentos consiste en la determinación de sus componentes volátiles. La primera etapa necesaria para realizar este tipo de análisis es el aislamiento y concentración de los mismos. Se ha realizado una revisión bibliográfica sobre las diferentes técnicas utilizadas para este fin en diferentes alimentos y especialmente en aceites vegetales. Los métodos utilizados son muy diversos, se ofrece una explicación de cada uno de ellos considerando las diferentes variantes existentes. Asimismo se detallan las aplicaciones realizadas en aceites vegetales durante los últimos años.

  8. l aceite de atún como fuente de ácidos grasos ω-3 en el huevo de gallina

    Directory of Open Access Journals (Sweden)

    Vázquez-Valladolid, J. L.

    2005-06-01

    Full Text Available Fish oils are a source of polyunsaturated omega 3 fatty acids (AG ω3, mainly eicosapentaenoic acid (EPA and docosahexaenoic acid (DHA, which supply many benefits to human health. Tuna oil was used as a source of marine 3ω FA to enrich eggs by supplementing the diet of egg-laying hens with tuna oil. One hundred and twenty White Leghorn hens of 90 weeks old were allocated on three treatments with four replicates each, on a completely random design. Treatments consisted of adding 1 % and 2 % of tuna oil to the diets. The total lipids and ω3FA of the eggs were determined. The egg-laying hen dietary tuna oil supplement (1 and 2 % enriched eggs with 300 % more EPA (0.40, 1.37, 1.54 mg/g lipids and DHA (7.90, 24.67, 24.50 mg/g lipids versus the control egg . The ω6:ω3 ratio decreased ( 11.4:1, 3.8:1, 3.0:1 as dietary tuna oil increased. There were no differences (p>0.05 among treatments in productive performance and egg quality, except egg weight which decreased with the tuna oil.Los aceites de pescado son una fuente de lípidos poliinsaturados de origen animal, principalmente de los ácidos grasos omega-3 (AG ω-3, eicosapentaenoico (EPA y docosahexaenoico (DHA, beneficiosos para la salud. En este trabajo se utilizó el aceite de atún como fuente de estos nutrientes en el huevo para consumo. Se utilizaron 120 gallinas blancas Leghorn Isa-Babcock B-300 de 90 semanas de edad, distribuidas al azar en tres tratamientos, con cuatro réplicas cada uno. Los tratamientos consistieron en adicionar 1% y 2% de aceite de atún en la dieta de las gallinas ponedoras. Se determinaron los lípidos totales y AG ω-3 en el huevo, obteniéndose 300 % más de EPA (0,40, 1,37, 1,54 mg/g lípidos y DHA (7,90, 24,67, 24,50 mg/g lípidos al adicionar 1 y 2% de aceite de atún en la dieta de las aves, que en el grupo testigo. La relación ω-6: ω-3 en el huevo disminuyó con el suplemento dietético de aceite de atún (11,4:1, 3,8:1, 3:1, lo mismo ocurri

  9. Combustion strategy : United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Greenhalgh, D. [Heriot-Watt Univ., Edingburgh, Scotland (United Kingdom). School of Engineering and Physical Sciences

    2009-07-01

    The United Kingdom's combustion strategy was briefly presented. Government funding sources for universities were listed. The United Kingdom Research Councils that were listed included the Arts and Humanities Research Council (AHRC) and the Biotechnology and Biological Sciences Research Council (BBSRC); the Engineering and Physical Sciences Research Council (EPSRC); the Economic and Social Research Council; the Medical Research Council; the Natural Environment Research Council; and the Science and Technology Facilities Council. The EPSRC supported 65 grants worth 30.5 million pounds. The combustion industry was noted to be dominated by three main players of which one was by far the largest. The 3 key players were Rolls-Royce; Jaguar Land Rover; and Doosan Babcock. Industry and government involvement was also discussed for the BIS Technology Strategy Board, strategy technology areas, and strategy application areas.

  10. Aerosols from biomass combustion

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T.

    2001-07-01

    This report is the proceedings of a seminar on biomass combustion and aerosol production organised jointly by the International Energy Agency's (IEA) Task 32 on bio energy and the Swiss Federal Office of Energy (SFOE). This collection of 16 papers discusses the production of aerosols and fine particles by the burning of biomass and their effects. Expert knowledge on the environmental impact of aerosols, formation mechanisms, measurement technologies, methods of analysis and measures to be taken to reduce such emissions is presented. The seminar, visited by 50 participants from 11 countries, shows, according to the authors, that the reduction of aerosol emissions resulting from biomass combustion will remain a challenge for the future.

  11. Plasma Assisted Combustion

    Science.gov (United States)

    2007-02-28

    Tracking an individual streamer branch among others in a pulsed induced discharge J. Phys. D: Appl. Phys. 35 2823--9 [29] van Veldhuizen E M and Rutgers...2005) AIAA–2005–0405. [99] E.M. Van Veldhuizen (ed) Electrical Discharges for Environmental Purposes: Fun- damentals and Applications (New York: Nova...Vandooren J, Van Tiggelen P J 1977 Reaction Mechanism and Rate Constants in Lean Hydrogen–Nitrous Oxide Flames Combust. Flame 28 165 [201] Dean A M, Steiner

  12. Fluid-bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, G.; Schoebotham, N.

    1981-02-01

    In Energy Equipment Company's two-stage fluidized bed system, partial combustion in a fluidized bed is followed by burn-off of the generated gases above the bed. The system can be retrofitted to existing boilers, and can burn small, high ash coal efficiently. It has advantages when used as a hot gas generator for process drying. Tests on a boiler at a Cadbury Schweppes plant are reported.

  13. Combustion science and engineering

    CERN Document Server

    Annamalai, Kalyan

    2006-01-01

    Introduction and Review of Thermodynamics Introduction Combustion Terminology Matter and Its Properties Microscopic Overview of Thermodynamics Conservation of Mass and Energy and the First Law of Thermodynamics The Second Law of Thermodynamics Summary Stoichiometry and Thermochemistry of Reacting Systems Introduction Overall Reactions Gas Analyses Global Conservation Equations for Reacting Systems Thermochemistry Summary Appendix Reaction Direction and Equilibrium Introduction Reaction Direction and Chemical Equilibrium Chemical Equilibrium Relations Vant Hoff Equation Adi

  14. Issues in waste combustion

    Energy Technology Data Exchange (ETDEWEB)

    Gustavsson, Lennart; Robertson, Kerstin; Tullin, Claes [Swedish National Testing and Research Inst., Boraas (Sweden); Sundquist, Lena; Wrangensten, Lars [AaF-Energikonsult AB, Stockholm (Sweden); Blom, Elisabet [AaF-Processdesign AB, Stockholm (Sweden)

    2003-05-01

    The main purpose of this review is to provide an overview of the state-of-the-art on research and development issues related to waste combustion with relevance for Swedish conditions. The review focuses on co-combustion in grate and fluidised bed furnaces. It is primarily literature searches in relevant databases of scientific publications with to material published after 1995. As a complement, findings published in different report series, have also been included. Since the area covered by this report is very wide, we do not claim to cover the issues included completely and it has not been possitile to evaluate the referred studies in depth. Basic knowledge about combustion issues is not included since such information can be found elsewhere in the literature. Rather, this review should be viewed as an overview of research and development in the waste-to-energy area and as such we hope that it will inspire scientists and others to further work in relevant areas.

  15. Biorremediación de lodos contaminados con aceites lubricantes usados

    Directory of Open Access Journals (Sweden)

    María Cristina Vásquez

    2010-01-01

    Full Text Available Los lodos contaminados con residuos de aceites lubricantes usados generan gran impacto ambiental negativo al no ser manejados adecuadamente. Se propuso la biorremediación para disminuir la concentración de dichos contaminantes. Los ensayos fueron realizados en las instalaciones de la planta de tratamiento de aguas residuales (PTAR de Río Frío (Girón, Santander, Colombia, donde se evaluaron consorcios microbianos nativos, que posteriormente se adicionaron a las biopilas conformadas por lodos deshidratados provenientes del tratamiento primario de aguas residuales domésticas (usados como fuente de materia orgánica, lodos provenientes de lavaderos de carros y lodos de alcantarillado de la zona industrial de la ciudad de Bucaramanga (Colombia. Se aislaron, identificaron y conservaron cepas microbianas con capacidad degradadora de hidrocarburos totales de petróleo (TPH como Pseudomonas spp., Acinetobacter spp, Enterobacter cloacae, Citrobacter spp., Bacillus brevis, Micrococcus spp y Nocardia spp. Se hizo una serie de pruebas piloto donde se inoculó cada montaje con un consorcio bacteriano a una concentración de 3x108 UFC/ml de bacterias y microorganismos fúngicos como Aspergillus spp., Fusarium spp., Trichoderma spp., a una concentración de 1x106 esporas/ml; se monitorearon parámetros de temperatura, pH, humedad y oxigenación. Se realizaron dos ensayos para verificar el comportamiento de dichos tratamientos; se analizó la variable continua TPH en ppm mediante el método de modelos mixtos lineares en bloques aleatorios completos, que revelaron diferencias significativas entre la biopila control y las biopilas bajo prueba; se obtuvieron porcentajes de remoción hasta de 94% de TPH en 120 días y 84% en 40 días, lo que reflejó un efecto positivo en la utilización de los consorcios de microorganismos bajo prueba en la descontaminación de lodos de alcantarillado industrial y lodos de lavaderos de carros.

  16. Composición química y actividad antibacteriana del aceite esencial de Peperomia acuminata de los Andes venezolanos

    Directory of Open Access Journals (Sweden)

    Flor D. Mora-Vivas

    2016-12-01

    Full Text Available El género Peperomia (Piperaceae, es bien conocido por sus especies ornamentales y usos etnomedicinales. En el presente trabajo se describe la caracterización química y la actividad antibacteriana del aceite esencial de Peperomia acuminata Ruiz & Pav. proveniente del Estado Mérida Venezuela. El aceite esencial se obtuvo por hidrodestilación de las hojas y la separación de los componentes se realizó por Cromatografía de gases-Espectrometría de Masas (CG/EM. Se logró la elucidación de ocho compuestos (96,7%, siendo el 2E-dodecenal el componente mayoritario (65% seguido de dodecanal (14,8% y tetradecanal (9,2%. Esta investigación muestra el potencial del aceite esencial de P. acuminata frente a bacterias Gram positivas (Staphylococcus aureus ATCC 25923 y Enterococcus faecalis 29212, con un valor de Concentración inhibitoria mínima de 1μL/mL. Este es el primer reporte sobre la composición química del aceite esencial de esta especie, por lo tanto una contribución importante al estudio del género Peperomia.

  17. Nuevo equipo de proceso de destilación fraccionada en continuo por arrastre con vapor de aceites esenciales del jugo de limón mexicano

    Directory of Open Access Journals (Sweden)

    Francisco J. Padilla M.

    2007-01-01

    Full Text Available En este trabajo se presenta un nuevo equipo llamado Destilador-Fraccionador Horizontal, para realizar el procesos de destilación fraccionada en continuo por arrastre de vapor de aceites esenciales obtenidos a partir del jugo de limón mexicano (Citrus aurantifolia. La capacidad de fraccionación del nuevo equipo es analizada con soluciones modelo y soluciones reales de jugo de limón. Se emplean diseños experimentales y métodos estadísticos para investigar el desempeño del equipo y para validar su capacidad de fraccionar. Mediante la determinación de la relación S/F (gramos de vapor necesario para extraer 1 g de aceite destilado en la fase vapor, se determina que el nuevo equipo requiere una menor cantidad de energía para lograr la separación de los aceites esenciales. Eficiencias de extracción de aceites esenciales superiores al 90% son alcanzadas empleando las soluciones reales de jugo de limón.

  18. Validación clínica y seguimiento en la oficina de farmacia de la utilidad del aceite esencial de romero como agente hipertensor

    OpenAIRE

    Fernández Martín, Luis Fernando

    2012-01-01

    El objetivo de esta tesis doctoral es probar que el uso tradicional del aceite esencial de romero en el tratamiento de la hipotensión esencial o primaria se basa en una evidencia que puede ser puesta de manifiesto mediante la realización e interpretación un estudio clínico.

  19. COMPARACIÓN DE DOS MÉTODOS DE EXTRACCIÓN DE ACEITE DE AJONJOLÍ: PERCOLACIÓN Y PRENSADO

    Directory of Open Access Journals (Sweden)

    RICARDO BENÍTEZ-BENÍTEZ

    Full Text Available Se aplicaron y compararon dos métodos de extracciÔn de aceite de ajonjolí, percolación y prensado, sobre semillas doradas (Sesamum Indicum L. En los aceites extraídos se evaluaron las propiedades fisicoquímicas y el perfil de ácidos grasos utilizando procedimientos estándar. Las semillas y tortas procedentes de las extracciones se analizaron por medio de análisis proximal y perfil de aminoácidos. Se compararon los resultados de la extracción a través de un análisis univariado seguido por la prueba T-student. El método de percolación produjo un rendimiento de extracción de aceite de ajonjolí (98° más alto que el prensado (94°, sin embargo, el aceite obtenido por prensado fue mejor desde el punto de vista nutricional mostrando valores más altos de ácidos grasos poliinsaturados. Los índices de peróxidos y Kreis indicaron una alta estabilidad oxidativa. Se encontraron diferencias estadísticamente significativas entre los porcentajes de humedad y grasa de las tortas, mientras que la composición de aminoácidos fue similar. Metionina, fenilalanina y tirosina fueron los aminoácidos más disponibles, y leucina, lisina y triptófano los limitantes.

  20. Upgraded wood residue fuels 1995

    International Nuclear Information System (INIS)

    Vinterbaeck, J.

    1995-01-01

    The Swedish market for upgraded residue fuels, i.e. briquettes, pellets and wood powder, has developed considerably during the nineties. The additional costs for the upgrading processes are regained and create a surplus in other parts of the system, e.g. in the form of higher combustion efficiencies, lower investment costs for burning equipment, lower operation costs and a diminished environmental impact. All these factors put together have resulted in a rapid growth of this part of the energy sector. In 1994 the production was 1.9 TWh, an increase of 37 % compared to the previous year. In the forthcoming heating season 1995/96 the production may reach 4 TWh. 57 refs, 11 figs, 6 tabs

  1. The Diesel Combustion Collaboratory: Combustion Researchers Collaborating over the Internet

    Energy Technology Data Exchange (ETDEWEB)

    C. M. Pancerella; L. A. Rahn; C. Yang

    2000-02-01

    The Diesel Combustion Collaborator (DCC) is a pilot project to develop and deploy collaborative technologies to combustion researchers distributed throughout the DOE national laboratories, academia, and industry. The result is a problem-solving environment for combustion research. Researchers collaborate over the Internet using DCC tools, which include: a distributed execution management system for running combustion models on widely distributed computers, including supercomputers; web-accessible data archiving capabilities for sharing graphical experimental or modeling data; electronic notebooks and shared workspaces for facilitating collaboration; visualization of combustion data; and video-conferencing and data-conferencing among researchers at remote sites. Security is a key aspect of the collaborative tools. In many cases, the authors have integrated these tools to allow data, including large combustion data sets, to flow seamlessly, for example, from modeling tools to data archives. In this paper the authors describe the work of a larger collaborative effort to design, implement and deploy the DCC.

  2. Internal combustion engine using premixed combustion of stratified charges

    Science.gov (United States)

    Marriott, Craig D [Rochester Hills, MI; Reitz, Rolf D [Madison, WI

    2003-12-30

    During a combustion cycle, a first stoichiometrically lean fuel charge is injected well prior to top dead center, preferably during the intake stroke. This first fuel charge is substantially mixed with the combustion chamber air during subsequent motion of the piston towards top dead center. A subsequent fuel charge is then injected prior to top dead center to create a stratified, locally richer mixture (but still leaner than stoichiometric) within the combustion chamber. The locally rich region within the combustion chamber has sufficient fuel density to autoignite, and its self-ignition serves to activate ignition for the lean mixture existing within the remainder of the combustion chamber. Because the mixture within the combustion chamber is overall premixed and relatively lean, NO.sub.x and soot production are significantly diminished.

  3. Optimización energética en la fabricación de baldosas cerámicas mediante el uso de aceite térmico

    Directory of Open Access Journals (Sweden)

    Mezquita, A.

    2012-08-01

    Full Text Available The ceramic tile manufacturing process consumes a great amount of energy, mainly thermal energy, which is obtained from natural gas combustion. The increased cost of this fuel and the current economic situation make cost a critical issue that can hurt company competitiveness. The ceramic tile firing process in roller kilns does not exactly stand out for its energy efficiency, because about 50% of the energy input is lost through the kiln combustion flue gas and cooling gas stacks. With a view to improving the reuse of the energy consumed in the firing operation, two heat exchangers were installed in the stacks of a kiln. In these heat exchangers, the kiln gases transfer their sensible heat to a thermal oil that then passes this on, through two other exchangers, to the drying gases in the recirculation ducts of a vertical dryer. This study presents an experimental industrial plant in a fine-tuning test phase, in which the preliminary results indicate an energy efficiency improvement in a range of 60–90%, depending on the operating conditions and processed materials.

    El proceso de fabricación de baldosas cerámicas consume gran cantidad de energía, mayoritariamente energía térmica, que se obtiene de la combustión de gas natural. El incremento del coste de este combustible, así como la situación económica actual, hace que este coste sea crítico para las empresas y pueda mermar su competitividad. El proceso de cocción de las baldosas cerámicas en hornos de rodillos no destaca precisamente por el aprovechamiento de la energía utilizada, pues aproximadamente el 50 % se pierde a través de las chimeneas de humos y de enfriamiento del horno. Con el objetivo de mejorar el aprovechamiento de la energía consumida durante la operación de cocción se han instalado, en las chimeneas de un horno, dos intercambiadores de calor, en los cuales los gases procedentes del horno ceden su calor sensible a un aceite térmico, que

  4. Determinación de esteroles en la fracción insaponificable del aceite de los frutos de la palma real cubana (Roystonea regia

    Directory of Open Access Journals (Sweden)

    David Marrero Delange

    2013-03-01

    Full Text Available Introducción: los esteroles han sido ampliamente estudiados por su importancia nutricional y farmacéutica. Sin embargo, para nuestro conocimiento, la composición de esteroles del aceite de los frutos de la palma real cubana (Roystonea regia no ha sido determinada hasta el momento. Objetivos: determinar la composición de esteroles que pudieran estar presentes en la fracción insaponificable del aceite de R. regia mediante CG-EM. Métodos: muestras de dos lotes de aceite de R. regia fueron sometidas al procedimiento para la determinación de esteroles establecido por el del Instituto de Nutracéuticos de los EE.UU., el cual consiste, fundamentalmente, en una saponificación con disolución de KOH/EtOH y posterior extracción con n-hexano de las fracciones insaponificables. Las fracciones obtenidas fueron analizadas por CG-EM como derivados TMS e identificadas por comparación de sus espectros con los de patrones comerciales y los de la base de espectros Wiley. Para la cuantificación se utilizó el colestano como patrón interno. Resultados: en la fracción insaponificable del aceite de R. regia se encontró un contenido total de esteroles de 66,1%; lo que representa un 0,14 % del aceite. La fracción de esteroles, estuvo compuesta principalmente por â -sitosterol (51,2 %, estigmasterol (9,6 %, campesterol (9,2 %, 24-metilen-cicloartanol (9,2 %, Ä5-avenasterol (8,9 %, cicloartanol (7,5 %; además de otros componentes minoritarios como cicloartenol, ã-sitosterol y colesterol. Conclusiones: se identificaron y se cuantificaron mediante CG-EM los esteroles de la fracción insaponificable del aceite de R. regia, en la cual el â-sitosterol resultó el componente mayoritario. Estos resultados son una contribución al estudio de la composición química de dicho aceite y pudieran avalar su posible utilidad nutricional y seguridad.

  5. Development of flameless combustion; Desarrollo de la combustion sin flama

    Energy Technology Data Exchange (ETDEWEB)

    Flores Sauceda, M. Leonardo; Cervantes de Gortari, Jaime Gonzalo [Universidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico)]. E-mail: 8344afc@prodigy.net.mx; jgonzalo@servidor.unam.mx

    2010-11-15

    The paper intends contribute to global warming mitigation joint effort that develops technologies to capture the CO{sub 2} produced by fossil fuels combustion and to reduce emission of other greenhouse gases like the NO{sub x}. After reviewing existing combustion bibliography is pointed out that (a) touches only partial aspects of the collective system composed by Combustion-Heat transfer process-Environment, whose interactions are our primary interest and (b) most specialists think there is not yet a clearly winning technology for CO{sub 2} capture and storage. In this paper the study of combustion is focused as integrated in the aforementioned collective system where application of flameless combustion, using oxidant preheated in heat regenerators and fluent gas recirculation into combustion chamber plus appropriated heat and mass balances, simultaneously results in energy saving and environmental impact reduction. [Spanish] El trabajo pretende contribuir al esfuerzo conjunto de mitigacion del calentamiento global que aporta tecnologias para capturar el CO{sub 2} producido por la combustion de combustibles fosiles y para disminuir la emision de otros gases invernadero como NOx. De revision bibliografica sobre combustion se concluye que (a) trata aspectos parciales del sistema compuesto por combustion-proceso de trasferencia de calor-ambiente, cuyas interacciones son nuestro principal interes (b) la mayoria de especialistas considera no hay todavia una tecnologia claramente superior a las demas para captura y almacenaje de CO{sub 2}. Se estudia la combustion como parte integrante del mencionado sistema conjunto, donde la aplicacion de combustion sin flama, empleando oxidante precalentado mediante regeneradores de calor y recirculacion de gases efluentes ademas de los balances de masa y energia adecuados, permite tener simultaneamente ahorros energeticos e impacto ambiental reducido.

  6. Observing and modeling nonlinear dynamics in an internal combustion engine

    International Nuclear Information System (INIS)

    Daw, C.S.; Kennel, M.B.; Finney, C.E.; Connolly, F.T.

    1998-01-01

    We propose a low-dimensional, physically motivated, nonlinear map as a model for cyclic combustion variation in spark-ignited internal combustion engines. A key feature is the interaction between stochastic, small-scale fluctuations in engine parameters and nonlinear deterministic coupling between successive engine cycles. Residual cylinder gas from each cycle alters the in-cylinder fuel-air ratio and thus the combustion efficiency in succeeding cycles. The model close-quote s simplicity allows rapid simulation of thousands of engine cycles, permitting statistical studies of cyclic-variation patterns and providing physical insight into this technologically important phenomenon. Using symbol statistics to characterize the noisy dynamics, we find good quantitative matches between our model and experimental time-series measurements. copyright 1998 The American Physical Society

  7. Efecto de la suplementación con aceite de pescado sobre la frecuencia cardíaca y temperatura rectal en perros sanos durante un programa de entrenamiento en cinta trotadora

    OpenAIRE

    Francisco Javier Pellegrino; Analía L. Risso; Yanina Alejandra Corrada

    2017-01-01

    El objetivo del presente estudio fue evaluar el efecto de la suplementación con aceite de pescado sobre la frecuencia cardíaca y temperatura rectal en perros sanos durante un programa de entrenamiento en cinta trotadora. En un diseño experimental cruzado, 5 perros machos fueron asignados aleatoriamente a los grupos control y aceite de pescado, y recibieron diariamente 54 mg de aceite de pescado/kg de peso corporal0,75. Todos fueron entrenados en cinta trotadora dos veces por semana durante 12...

  8. Interacción de los efectos del policosanol y el aceite de pescado sobre el tiempo de sangrado y la agregación plaquetaria intravascular en ratas

    OpenAIRE

    Vivian Molina; Lourdes Arruzazabala; Daisy Carbajal; Rosa Más

    2009-01-01

    El consumo de aceite de pescado ha mostrado reducir los eventos cardiovasculares por lo cual investigar si su administración con terapias concomitantes aporta beneficios adicionales resulta de interés. Estudios experimentales y clínicos han mostrado que la administración conjunta de aceite de pescado y policosanol muestra beneficios añadidos sobre el perfil lipídico y la agregación plaquetaria inducida ex vivo. Este trabajo investigó si la terapia combinada aceite de pescado + policosanol mos...

  9. Obtención de biodiesel con aceite de maíz usado en frituras y metacaolinita como catalizador Obtención de biodiesel con aceite de maíz usado en frituras y metacaolinita como catalizador

    Directory of Open Access Journals (Sweden)

    Jorge Medina-Valtierra

    2012-02-01

    Full Text Available Se investigó la producción de biodiesel usando un reactor intermitente, se utilizó la metacaolinita como un catalizador sólido ácido que presentó una alta actividad para la pro­ducción de biodiesel a partir de aceite de maíz usado en freidora. El área superficial de la metacaolinita, diámetro de poro y volumen de poro fueron 10 m2/g, 13.0 nm y 30 mm3/g, respectivamente. Las condiciones óptimas para la reacción de transesterificación fueron: una relación molar aceite/metanol 1:31, temperatura de 160 ºC, presión manométrica de 1.65 MPa y una cantidad de catalizador de 3 (% peso. El rendimiento de ésteres metílicos de ácidos grasos (biodiesel fue de 92.4 % para 2 h de reacción. Este método de preparación de biodiesel puede ser una buena alternativa para la utilización de aceite de maíz usado en freidora como una fuente muy barata para la producción de biodiesel combinado con un catalizador barato y además amigable con el medio ambiente.Biodiesel production with used frying corn oil by transesterification reaction, with methanol, using a commercial kaolinite thermally-activated solid acid catalyst was investigated. The surface area, the average pore diameter and volume of pore of metakaolinite were 10 m2/g, 13.0 nm and 30 mm3/g, respectively. The optimal conditions for the transesterification reaction were determinate to be oil/methanol, in a molar ratio 1:31, temperature 160 ºC, manometer pressure of 1.65 MPa and catalyst concentration of 3 % (w/w. The yield of fatty acid methyl esters (biodiesel was 92.4 % after 2 h of reaction. This method of preparation of biodiesel can be a positive alternative for utilizing used frying corn oil for feedstock of biodiesel combined with the cited inexpensive, “green” catalyst.

  10. Contenido del aceite esencial en el follaje de Pinus caribaea Morelet según la época del Año. I

    Directory of Open Access Journals (Sweden)

    Rolando Quert Álvarez

    1998-04-01

    Full Text Available Se realizó un estudio con el objetivo de determinar el contenido de aceite esencial en el follaje verde de la especie Pinus caribaea Morelet y cómo varía éste según los diferentes meses del año. Se determinaron el tiempo de destilación del aceite esencial a escala de laboratorio, el tamaño de muestra en nuestras condiciones de trabajo y el contenido de aceite esencial durante 2 años, mediante el análisis del contenido de aceite esencial de enero a diciembre. El tiempo de destilación obtenido fue de 3 h y el tamaño de muestra de 3 árboles. Los más altos rendimientos de aceite esencial se obtuvieron en los meses de marzo y abril y los más bajos entre noviembre y diciembre.A study was conducted aimed at determining the content of essential oil in the green foliage of the Pinus caribea Morelet species and at knowing how it varies according to the month of the year. The time of distillation of the essential oil at laboratory scale, the size of the sample under our working conditions, and the content of essential oil during two years were determined by analyzing the content of essential oil from January to December. The distillation time obtained was of 3 hours and the size of the sample was of 3 trees. The highest yields of essential oil were obtained in March and April, where as the lowest ones were attained between November and December.

  11. Efecto de la fertilización nitrogenada en el rendimiento y la composición de los aceites esenciales de especies y accesiones de Lippia

    Directory of Open Access Journals (Sweden)

    érika Leonor Zambrano M

    2013-04-01

    Full Text Available En el Centro Experimental de la Universidad Nacional de Colombia sede Palmira (CEUNP se evaluó el efecto de la aplicación de nitrógeno (N en la producción de materia seca y aceites esenciales de dos especies de Lippia. Se utilizaron las accesiones Cítrica y Típica de Lippia alba (Miller N.E.Brown ex Britton & Wilson y Patía, Típica y Cítrica de L. origanoides H.B.K. Como fuentes de N se aplicaron gallinaza y urea en dosis equivalentes de 50 y 100 kg/ha de N. Se utilizó un diseño experimental de bloques completos al azar, con cinco tratamientos y tres repeticiones para cada accesión. Se evaluaron los rendimientos de biomasa fresca y seca (MS y de los aceites esenciales y su composición por arrastre de vapor en hojas secas. Los mayores rendimientos de MS y de aceite esencial (3.318 kg/ha y 82.9 lt/ha, respectivamente se obtuvieron con las accesiones de L origanoides. La mayor concentración de aceite esencial (4 ml/100 g se registró en L. origanoides Patía con la aplicación de 100 kg/ha de N como urea. Las diferencias en la composición química de los aceites estuvieron más asociadas con la especie y accesión que con la aplicación de N.

  12. Influencia del riego sobre la composición y características organolépticas del aceite de oliva

    Directory of Open Access Journals (Sweden)

    Salas, J.

    1997-04-01

    Full Text Available Fatty acidic composition, organoleptic characteristics and other quality parameters of virgin olive oils were evaluated in dry-farming and irrigated olive orchards. The acidic composition was affected by irrigation. The content in monoinsaturated and polunsaturated fatty acid was higher in the oils of the dry-farming olive orchard, while the relative content in saturated fatty acids was higher in the irrigated one. The insaturated/ saturated and oleic/linoleic relations distinguish the irrigated and non irrigated olive trees. The K225 values, the poliphenolic contents and the bitter taste were also correlated. The oils from non irrigated olive trees showed the higher bitter taste. Those three parameters discriminated the oils from irrigated and non irrigated trees. The bitter taste diminished when increasing the amount of water supplied with the irrigation.

    Se estudia la composición relativa en ácidos grasos, características organolépticas y parámetros de calidad de los aceites producidos en olivares de secano o regados con diferentes dosis de agua. La composición acídica fue alterada por el riego. El contenido en ácidos grasos monoinsaturados y poliinsaturados fue mayor en los aceites de secano, mientras que el contenido relativo en ácidos grasos saturados fue mayor en regadío. Las relaciones insaturados/saturados y oleico/linoleico diferencian los aceites de riego y de secano. Existió una relación entre los valores de K225, el contenido en polifenoles y el grado de amargor, siendo los aceites de secano mucho más amargos que los de riego, discriminando estos tres parámetros los aceites de riego y los de secano. El grado de amargor disminuyó al aumentar la cantidad de agua aportada con el riego.

  13. Actividad antimicótica in vitro y metabolitos del aceite esencial de las hojas de Minthostachys Mollis (muña

    Directory of Open Access Journals (Sweden)

    Carlos Cano

    2008-07-01

    Full Text Available Objetivos. Demostrar la actividad antimicótica in vitro y la elucidación de algunos de los metabolitos del aceite esencial de hojas de Minthostachys mollis (muña proveniente del distrito de Huacrapuquio (2700 msnm, Junín. Materiales y métodos. El aceite esencial se obtuvo por el método de destilación por arrastre de vapor de agua. Este fue sometido a análisis físico-químico y determinación de la composición química mediante cromatografía de gases. Mediante el método de agar en difusión se evaluó la inhibición del crecimiento fúngico de Candida albicans y también por el método de dilución en tubo para Trichophytun tonsurans, Trichophytun mentagrophytes, Microsporun canis. Resultados. Se encontraron los siguientes monoterpenos: pulegona, mentona, limoneno y mirceno. El aceite esencial de muña inhibió completamente el desarrollo de T. tonsurasn, T. mentagrophytes y M. canis con ambos métodos de evaluación y dosis, para C. albicans se logró un halo de inhibición de 30 mm para el aceite esencial al 100% y de 35 mm al 50%. Conclusiones. Se demostró la actividad antimicótica del aceite esencial de muña, probablemente por la acción de los monoterpenos encontrados.

  14. Treatment of alpha-bearing combustible wastes using acid digestion

    International Nuclear Information System (INIS)

    Lerch, R.E.; Allen, C.R.; Blasewitz, A.G.

    1977-11-01

    Acid digestion has been developed at the Hanford Engineering Development Laboratory (HEDL) in Richland, Washington to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to demonstrate the process using radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September 1977 and is currently undergoing cold shakedown tests. Hot operation is expected in May 1978. Features of RADTU include: storage and transfer station for incoming wastes, a feed preparation station, an extrusion feed mechanism for transfer of the waste to the acid digester, the acid digester, a residue recovery system, and an off-gas treatment system

  15. Treatment of alpha-bearing combustible wastes using acid digestion

    International Nuclear Information System (INIS)

    Lerch, R.E.; Allen, C.R.; Blasewitz, A.G.

    1978-01-01

    Acid digestion has been developed at the Hanford Engineering Development Laboratory (HEDL) in Richland, Washington to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to demonstrate the process using radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September 1977 and is currently undergoing cold shakedown tests. Hot operation is expected in May 1978. Features of RADTU include: storage and transfer station for incoming wastes, a feed preparation station, an extrusion feed mechanism for transfer of the waste to the acid digester, the acid digester a residue recovery system, and an off-gas treatment system

  16. Co-combustion of risk husk with coal in a fluidized bed

    International Nuclear Information System (INIS)

    Ghani, A.K.; Alias, A.B.; Savory, R.M.; Cliffe, K.R.

    2006-01-01

    Power generation from biomass is an attractive technology which utilizes agricultural residue waste. In order to explain the behavior of biomass-fired fluidized bed incinerator, biomass sources from agricultural residues (rice husk) was co-fired with coal in a 0.15 m diameter and 2.3 m high fluidized bed combustor. The combustion efficiency and CO emissions were studied and compared with those for pure coal combustion. Biomass waste with up to 70% mass fraction can be co-combusted in a fluidized bed combustor designed for coal combustion with a maximum drop of efficiency of 20% depending upon excess air levels. CO levels fluctuated between 200-700 ppm were observed when coal is added. It is evident from this research that efficient co-firing of rice husk with coal can be achieved with minimum modification of existing coal-fired boilers. (Author)

  17. Sulfur Chemistry in Combustion I

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Glarborg, Peter

    2000-01-01

    of the sulphur compounds in fossil fuels and the possibilities to remove them will be given. Then the combustion of sulphur species and their influence on the combustion chemistry and especially on the CO oxidation and the NOx formation will be described. Finally the in-situ removal of sulphur in the combustion...... process by reaction between SO2 and calcium containing sorbents and the influence on the NOx chemistry will be treated....

  18. Pulsating combustion - Combustion characteristics and reduction of emissions

    Energy Technology Data Exchange (ETDEWEB)

    Lindholm, Annika

    1999-11-01

    In the search for high efficiency combustion systems pulsating combustion has been identified as one of the technologies that potentially can meet the objectives of clean combustion and good fuel economy. Pulsating combustion offers low emissions of pollutants, high heat transfer and efficient combustion. Although it is an old technology, the interest in pulsating combustion has been renewed in recent years, due to its unique features. Various applications of pulsating combustion can be found, mainly as drying and heating devices, of which the latter also have had commercial success. It is, however, in the design process of a pulse combustor, difficult to predict the operating frequency, the heat release etc., due to the lack of a well founded theory of the phenomenon. Research concerning control over the combustion process is essential for developing high efficiency pulse combustors with low emissions. Natural gas fired Helmholtz type pulse combustors have been the experimental objects of this study. In order to investigate the interaction between the fluid dynamics and the chemistry in pulse combustors, laser based measuring techniques as well as other conventional measuring techniques have been used. The experimental results shows the possibilities to control the combustion characteristics of pulsating combustion. It is shown that the time scales in the large vortices created at the inlet to the combustion chamber are very important for the operation of the pulse combustor. By increasing/decreasing the time scale for the large scale mixing the timing of the heat release is changed and the operating characteristics of the pulse combustor changes. Three different means for NO{sub x} reduction in Helmholtz type pulse combustors have been investigated. These include exhaust gas recirculation, alteration of air/fuel ratio and changed inlet geometry in the combustion chamber. All used methods achieved less than 10 ppm NO{sub x} emitted (referred to stoichiometric

  19. Influencia de la salinidad edáfica sobre la calidad del aceite de oliva cv. Arbequina

    Directory of Open Access Journals (Sweden)

    Aragüés, R.

    2005-03-01

    Full Text Available This work analyzes the effect of soil salinity on olive oil quality. The chemical composition of oils extracted from young ‘Arbequina' olives subject in the field to three soil salinity levels (low-L, medium-M and high-H was determined throughout a period of three years. A total of 30 parameters were analyzed (moisture, oil content, acidity, peroxides, ultraviolet absorbances, poliphenols, aliphatic alcohols, sterols, waxes, and fatty acid composition. Soil salinity was measured on fourteen different dates with an electromagnetic sensor. Overall, salinity increased oil content (+15 % in H with respect to L and decreased aliphatic alcohols (-29 % and palmitoleic acid (-32 % (values significant at P0,05. In summary, olive oil quality was practically independent of soil salinity and, according to the prevailing legislation, all the oils were classified as “extra virgin”.Este trabajo analiza el efecto de la salinidad edáfica sobre la calidad del aceite de oliva. Durante tres campañas se determinó la composición química de aceites provenientes de olivos jóvenes ‘Arbequina' sujetos en campo a tres niveles de salinidad (baja-B, media-M y alta-A. En total se analizaron 30 parámetros (humedad, grasa, acidez, peróxidos, lecturas en el ultravioleta, polifenoles, alcoholes alifáticos, esteroles, ceras y composición de ácidos grasos. La salinidad edáfica se midió en catorce fechas con un sensor electromagnético. La salinidad produjo un aumento del porcentaje de grasa (+15 % en A respecto a B, y un descenso de los alcoholes alifáticos (-29 % y del ácido palmitoleico (-32 % (valores significativos a P0,05. En conclusión, la calidad del aceite de oliva fue prácticamente independiente de la salinidad, clasificándose en todos los casos como “virgen extra” según la normativa vigente.

  20. Combustion from basics to applications

    CERN Document Server

    Lackner, Maximilian; Winter, Franz

    2013-01-01

    Combustion, the process of burning, is defined as a chemical reaction between a combustible reactant (the fuel) and an oxidizing agent (such as air) in order to produce heat and in most cases light while new chemical species (e.g., flue gas components) are formed. This book covers a gap on the market by providing a concise introduction to combustion. Most of the other books currently available are targeted towards the experienced users and contain too many details and/or contain knowledge at a fairly high level. This book provides a brief and clear overview of the combustion basics, suitable f

  1. Mathematical Modeling in Combustion Science

    CERN Document Server

    Takeno, Tadao

    1988-01-01

    An important new area of current research in combustion science is reviewed in the contributions to this volume. The complicated phenomena of combustion, such as chemical reactions, heat and mass transfer, and gaseous flows, have so far been studied predominantly by experiment and by phenomenological approaches. But asymptotic analysis and other recent developments are rapidly changing this situation. The contributions in this volume are devoted to mathematical modeling in three areas: high Mach number combustion, complex chemistry and physics, and flame modeling in small scale turbulent flow combustion.

  2. Optical Study of Flow and Combustion in an HCCI Engine with Negative Valve Overlap

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Trevor S [Jaguar Cars Ltd., Whitley Engineering Centre, Coventry. CV3 4LF (United Kingdom); Xu Hongming [Jaguar Cars Ltd., Whitley Engineering Centre, Coventry. CV3 4LF (United Kingdom); Richardson, Steve [Jaguar Cars Ltd., Whitley Engineering Centre, Coventry. CV3 4LF (United Kingdom); Wyszynski, Miroslaw L [University of Birmingham, Edgbaston, Birmingham. B15 2TT (United Kingdom); Megaritis, Thanos [University of Birmingham, Edgbaston, Birmingham. B15 2TT (United Kingdom)

    2006-07-15

    One of the most widely used methods to enable Homogeneous Charge Compression Ignition (HCCI) combustion is using negative valve overlapping to trap a sufficient quantity of hot residual gas. The characteristics of air motion with specially designed valve events having reduced valve lift and durations associated with HCCI engines and their effect on subsequent combustion are not yet fully understood. In addition, the ignition process and combustion development in such engines are very different from those in conventional spark-ignition or diesel compression ignition engines. Very little data has been reported concerning optical diagnostics of the flow and combustion in the engine using negative valve overlapping. This paper presents an experimental investigation into the in-cylinder flow characteristics and combustion development in an optical engine operating in HCCI combustion mode. PIV measurements have been taken under motored engine conditions to provide a quantitative flow characterisation of negative valve overlap in-cylinder flows. The ignition and combustion process was imaged using a high resolution charge coupled device (CCD) camera and the combustion imaging data was supplemented by simultaneously recorded in-cylinder pressure data which assisted the analysis of the images. It is found that the flow characteristics with negative valve overlapping are less stable and more valve event driven than typical spark ignition in-cylinder flows, while the combustion initiation locations are not uniformly distributed.

  3. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Ziemkiewicz, Paul; Vandivort, Tamara; Pflughoeft-Hassett, Debra; Chugh, Y Paul; Hower, James

    2008-08-31

    Each year, over 100 million tons of solid byproducts are produced by coal-burning electric utilities in the United States. Annual production of flue gas desulfurization (FGD) byproducts continues to increase as the result of more stringent sulfur emission restrictions. In addition, stricter limits on NOx emissions mandated by the 1990 Clean Air Act have resulted in utility burner/boiler modifications that frequently yield higher carbon concentrations in fly ash, which restricts the use of the ash as a cement replacement. Controlling ammonia in ash is also of concern. If newer, “clean coal” combustion and gasification technologies are adopted, their byproducts may also present a management challenge. The objective of the Combustion Byproducts Recycling Consortium (CBRC) is to develop and demonstrate technologies to address issues related to the recycling of byproducts associated with coal combustion processes. A goal of CBRC is that these technologies, by the year 2010, will lead to an overall ash utilization rate from the current 34% to 50% by such measures as increasing the current rate of FGD byproduct use and increasing in the number of uses considered “allowable” under state regulations. Another issue of interest to the CBRC would be to examine the environmental impact of both byproduct utilization and disposal. No byproduct utilization technology is likely to be adopted by industry unless it is more cost-effective than landfilling. Therefore, it is extremely important that the utility industry provide guidance to the R&D program. Government agencies and privatesector organizations that may be able to utilize these materials in the conduct of their missions should also provide input. The CBRC will serve as an effective vehicle for acquiring and maintaining guidance from these diverse organizations so that the proper balance in the R&D program is achieved.

  4. The combustion of sodium

    International Nuclear Information System (INIS)

    Newman, R.N.

    1978-01-01

    The burning rates of sodium in the form of vapour jets, droplets, sprays and unconfined and confined pools have been reviewed. Attention has been paid to assessing the value of models in the various combustion modes. Additional models have been constructed for the descriptions of laminar and turbulent vapour jets, stationary droplets, forced convection over ambient pool fires together with correlations for peak pressures in confined pool environments. Where appropriate experiments with sodium have not been conducted, the likely behaviour is predicted by comparison with the burning of other fuels, particularly in the field of large free ambient fires. Some areas where further knowledge is required are highlighted. (author)

  5. Alternate fuels; Combustibles alternos

    Energy Technology Data Exchange (ETDEWEB)

    Romero Paredes R, Hernando; Ambriz G, Juan Jose [Universidad Autonoma Metropolitana. Iztapalapa (Mexico)

    2003-07-01

    In the definition and description of alternate fuels we must center ourselves in those technological alternatives that allow to obtain compounds that differ from the traditional ones, in their forms to be obtained. In this article it is tried to give an overview of alternate fuels to the conventional derivatives of petroleum and that allow to have a clear idea on the tendencies of modern investigation and the technological developments that can be implemented in the short term. It is not pretended to include all the tendencies and developments of the present world, but those that can hit in a relatively short term, in accordance with agreed with the average life of conventional fuels. Nevertheless, most of the conversion principles are applicable to the spectrum of carbonaceous or cellulosic materials which are in nature, are cultivated or wastes of organic origin. Thus one will approach them in a successive way, the physical, chemical and biological conversions that can take place in a production process of an alternate fuel or the same direct use of the fuel such as burning the sweepings derived from the forests. [Spanish] En la definicion y descripcion de combustibles alternos nos debemos centrar en aquellas alternativas tecnologicas que permitan obtener compuestos que difieren de los tradicionales, al menos en sus formas de ser obtenidos. En este articulo se pretende dar un panorama de los combustibles alternos a los convencionales derivados del petroleo y que permita tener una idea clara sobre las tendencias de la investigacion moderna y los desarrollos tecnologicos que puedan ser implementados en el corto plazo. No se pretende abarcar todas las tendencias y desarrollos del mundo actual, sino aquellas que pueden impactar en un plazo relativamente corto, acordes con la vida media de los combustibles convencionales. Sin embargo, la mayor parte de los principios de conversion son aplicables al espectro de materiales carbonaceos o celulosicos los cuales se

  6. Fluidised bed combustion system

    International Nuclear Information System (INIS)

    McKenzie, E.C.

    1976-01-01

    Fluidized bed combustion systems that facilitates the maintenance of the depth of the bed are described. A discharge pipe projects upwardly into the bed so that bed material can flow into its upper end and escape downwardly. The end of the pipe is surrounded by an enclosure and air is discharged into the enclosure so that material will enter the pipe from within the enclosure and have been cooled in the enclosure by the air discharged into it. The walls of the enclosure may themselves be cooled

  7. Fuel and combustion stratification study of Partially Premixed Combustion

    NARCIS (Netherlands)

    Izadi Najafabadi, M.; Dam, N.; Somers, B.; Johansson, B.

    2016-01-01

    Relatively high levels of stratification is one of the main advantages of Partially Premixed Combustion (PPC) over the Homogeneous Charge Compression Ignition (HCCI) concept. Fuel stratification smoothens heat release and improves controllability of this kind of combustion. However, the lack of a

  8. Decommissioning Combustible Waste Treatment using Oxygen-Enriched Incinerator

    Energy Technology Data Exchange (ETDEWEB)

    Min, Byungyoun; Lee, Yoonji; Yun, Gyoungsu; Lee, Kiwon; Moon, Jeikwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    The aim of the paper is current status of treatment for the decommissioning combustible waste in KAERI and for the purpose of the volume reduction and clearance for decommissioning combustible wastes generated by the decommissioning projects. The incineration technology has been selected for the treatment of combustible wastes. About 34 tons of decommissioning combustible waste has been treated using Oxygen Enriched incineration. Temperature, pressure of major components, stack gas concentration, i. e., SOx, NOx, CO, CO{sub 2} and HCl, and the residual oxygen were measured. Measured major parameters during normal operation were sustained on a stable status within a criteria operation condition. Oxygen enriched air, 22vol. % (dry basis) was used for stable incineration. The volume reduction ratio has achieved about 1/117. The incineration with decommissioning radioactive combustible waste is possible with moderate oxygen enrichment of 22 vol.% (dry basis) into the supply air. The incineration facility operated quite smoothly through the analysis major critical parameters of off-gas. The pressure, off-gas flow and temperature of major components remained constant within the range specified. The measures gases and particulate materials in stack were considerably below the regulatory limits. The achieved volume reduction ratio through incineration is about 1/117.

  9. A Numerical Comparison of Spray Combustion between Raw and Water-in-Oil Emulsified Fuel

    Directory of Open Access Journals (Sweden)

    D. Tarlet

    2010-03-01

    Full Text Available Heavy fuel-oils, used engine oils and animal fat can be used as dense, viscous combustibles within industrial boilers. Burning these combustibles in the form of an emulsion with water enables to decrease the flame length and the formation of carbonaceous residue, in comparison with raw combustibles. These effects are due to the secondary atomization among the spray, which is a consequence of the micro-explosion phenomenon. This phenomenon acts in a single emulsion droplet by the fast (< 0.1 ms vaporization of the inside water droplets, leading to complete disintegration of the whole emulsion droplet. First, the present work demonstrates a model of spray combustion of raw fuel. Secondly, the spray combustion of water-in-oil emulsified fuel is exposed to the same burning conditions, taking into account the micro-explosion phenomenon. Finally, the comparison between the results with and without second atomization shows some similar qualitative tendencies with experimental measurements from the literature.

  10. Combustion Stratification for Naphtha from CI Combustion to PPC

    KAUST Repository

    Vallinayagam, R.

    2017-03-28

    This study demonstrates the combustion stratification from conventional compression ignition (CI) combustion to partially premixed combustion (PPC). Experiments are performed in an optical CI engine at a speed of 1200 rpm for diesel and naphtha (RON = 46). The motored pressure at TDC is maintained at 35 bar and fuelMEP is kept constant at 5.1 bar to account for the difference in fuel properties between naphtha and diesel. Single injection strategy is employed and the fuel is injected at a pressure of 800 bar. Photron FASTCAM SA4 that captures in-cylinder combustion at the rate of 10000 frames per second is employed. The captured high speed video is processed to study the combustion homogeneity based on an algorithm reported in previous studies. Starting from late fuel injection timings, combustion stratification is investigated by advancing the fuel injection timings. For late start of injection (SOI), a direct link between SOI and combustion phasing is noticed. At early SOI, combustion phasing depends on both intake air temperature and SOI. In order to match the combustion phasing (CA50) of diesel, the intake air temperature is increased to 90°C for naphtha. The combustion stratification from CI to PPC is also investigated for various level of dilution by displacing oxygen with nitrogen in the intake. The start of combustion (SOC) was delayed with the increase in dilution and to compensate for this, the intake air temperature is increased. The mixture homogeneity is enhanced for higher dilution due to longer ignition delay. The results show that high speed image is initially blue and then turned yellow, indicating soot formation and oxidation. The luminosity of combustion images decreases with early SOI and increased dilution. The images are processed to generate the level of stratification based on the image intensity. The level of stratification is same for diesel and naphtha at various SOI. When O concentration in the intake is decreased to 17.7% and 14

  11. Insecticides authorized for use on olive trees and the relationship between their registration and residues in olive oil

    Directory of Open Access Journals (Sweden)

    Lentza-Rizos, Ch.

    1996-12-01

    Full Text Available In order to eliminate losses due to insect attack, several insecticides are used on olive trees. Their residues in olive oil constitute an important parameter of its quality and must be monitored regularly and kept as low possible in order to ensure consumer protection. In this paper the insecticides authorized for use on olive trees are listed and their ADIs and Codex Alimentarius MRLs reported. The existing registrations are discussed from the point of view of their residues in oil.

    Diversos insecticidas son usados para eliminar las pérdidas debidas al ataque de insectos en olivos. Sus residuos en el aceite de oliva constituyen un parámetro importante de su calidad y deben ser controlados con regularidad y mantenidos tan bajos como sea posible en orden a asegurar la protección del consumidor. En este artículo se incluyen los distintos insecticidas autorizados para su uso en olivos así como los valores de ingesta diaria aceptable para el hombre y los límites máximos autorizados de los mismos. Los registros existentes se discuten desde el punto de vista de sus residuos en el aceite.

  12. Some Factors Affecting Combustion in an Internal-Combustion Engine

    Science.gov (United States)

    Rothrock, A M; Cohn, Mildred

    1936-01-01

    An investigation of the combustion of gasoline, safety, and diesel fuels was made in the NACA combustion apparatus under conditions of temperature that permitted ignition by spark with direct fuel injection, in spite of the compression ratio of 12.7 employed. The influence of such variables as injection advance angle, jacket temperature, engine speed, and spark position was studied. The most pronounced effect was that an increase in the injection advance angle (beyond a certain minimum value) caused a decrease in the extent and rate of combustion. In almost all cases combustion improved with increased temperature. The results show that at low air temperatures the rates of combustion vary with the volatility of the fuel, but that at high temperatures this relationship does not exist and the rates depend to a greater extent on the chemical nature of the fuel.

  13. Preliminary assessment of combustion modes for internal combustion wave rotors

    Science.gov (United States)

    Nalim, M. Razi

    1995-01-01

    Combustion within the channels of a wave rotor is examined as a means of obtaining pressure gain during heat addition in a gas turbine engine. Several modes of combustion are considered and the factors that determine the applicability of three modes are evaluated in detail; premixed autoignition/detonation, premixed deflagration, and non-premixed compression ignition. The last two will require strong turbulence for completion of combustion in a reasonable time in the wave rotor. The compression/autoignition modes will require inlet temperatures in excess of 1500 R for reliable ignition with most hydrocarbon fuels; otherwise, a supplementary ignition method must be provided. Examples of combustion mode selection are presented for two core engine applications that had been previously designed with equivalent 4-port wave rotor topping cycles using external combustion.

  14. Niveles de calcio, magnesio, manganeso, zinc, selenio y cromo en aceites de oliva comercializados en Andalucía

    Directory of Open Access Journals (Sweden)

    López, M.a Carmen

    2000-12-01

    Full Text Available We determined the presence of Ca, Mg, Mn, Zn, Se and Cr in 64 samples of olive virgin oil, olive oil and marc oil produced in Andalusia, southern Spain. Flame atomization atomic absorption spectroscopy was used for Ca and Mg, and the electrothermal atomization mode was used for Mn, Zn, Se and Cr. Samples were previously ashed with HNO3 and V2O5. Analytical conditions were optimized to control for interference and to obtain appropriate accuracy and precision factors. The method is potentially useful for quality control of olive oils. The concentrations ranged from 0.055 to 2.725 mg/kg for Ca; 0.300 to 5.300 mg/kg for Mg, 13.213 to 296.356 mg/kg for Mn, 8.758 to 36.575 mg/kg for Zn, undetectable to 178.515 mg/kg for Se, and undetectable to 41.510 mg/kg for Cr. No statistically significant differences were found between the three types of oil in the concentrations of these elements. There were significant correlations between the concentrations of the pairs Se-Cr, Mn-Cr, Mg-Zn, Ca-Zn and Ca-Cr. Because of the high intake of olive oil in our setting, this food can be considered a major source of essential elemental nutrients.En el presente trabajo se ha determinado la presencia de Ca, Mg, Mn, Zn, Se y Cr en 64 muestras de aceite de oliva virgen, de oliva y de orujo de oliva producidos en Andalucía. La técnica analítica empleada ha sido la espectroscopía de absorción atómica con atomización de llama para Ca y Mg, y con atomización electrotérmica para Mn, Zn, Se y Cr. Las muestras han sido sometidas previamente a mineralización ácida con HNO3 y V2O5. Se han optimizado las condiciones analíticas que permiten controlar interferencias y obtener factores de exactitud y precisión adecuados. El método propuesto resulta útil en control de calidad de aceites. Los valores obtenidos de Ca oscilan entre 0.055-2.725 mg/kg, de Mg entre 0.300-5.300 mg/kg, de Mn 13.213-296.356 mg/kg, de Zn entre 8.758-36.575 mg/kg, de Se entre no detectable -178

  15. Path planning during combustion mode switch

    Science.gov (United States)

    Jiang, Li; Ravi, Nikhil

    2015-12-29

    Systems and methods are provided for transitioning between a first combustion mode and a second combustion mode in an internal combustion engine. A current operating point of the engine is identified and a target operating point for the internal combustion engine in the second combustion mode is also determined. A predefined optimized transition operating point is selected from memory. While operating in the first combustion mode, one or more engine actuator settings are adjusted to cause the operating point of the internal combustion engine to approach the selected optimized transition operating point. When the engine is operating at the selected optimized transition operating point, the combustion mode is switched from the first combustion mode to the second combustion mode. While operating in the second combustion mode, one or more engine actuator settings are adjusted to cause the operating point of the internal combustion to approach the target operating point.

  16. AIR EMISSIONS FROM SCRAP TIRE COMBUSTION

    Science.gov (United States)

    The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

  17. Plasma igniter for internal-combustion engines

    Science.gov (United States)

    Breshears, R. R.; Fitzgerald, D. J.

    1978-01-01

    Hot ionized gas (plasma) ignites air/fuel mixture in internal combustion engines more effectively than spark. Electromagnetic forces propel plasma into combustion zone. Combustion rate is not limited by flame-front speed.

  18. SIMULACIÓN METABÓLICA DE LA BIODEGRADACIÓN DE ACEITES DIELÉCTRICOS USANDO SISTEMAS EXPERTO

    Directory of Open Access Journals (Sweden)

    EDISON ALEXANDER AGUDELO

    2011-01-01

    Full Text Available La rápida industrialización y la acelerada producción de nuevos compuestos sintéticos han llevado a los gobiernos y entidades de control a regular de forma estricta los vertimientos de efluentes industriales. Sin embargo, con decenas de nuevos compuestos generados cada año, es imposible establecer protocolos de tratabilidad y estimar su impacto directo en los ecosistemas antes de su producción en industria. El uso de sistemas de predicción de rutas metabólicas permite estimar de forma preliminar las posibles transformaciones que un compuesto complejo puede sufrir como resultado de su interacción con ecosistemas, dando un indicio de la facilidad del tratamiento biológico y su riesgo para a salud del medio ambiente. En este trabajo se presenta la simulación de la biodegradación de tres compuestos de referencia presentes en tierra Fuller contaminada con aceites dieléctricos, con el ánimo de estimar su biodegradabilidad y la posible generación de intermediarios tóxicos. Para cada compuesto se identificaron sus principales transformaciones, así como las enzimas involucradas y los posibles microorganismos que propician estas transformaciones. Se comprobó que los contaminantes pueden ser biodegradados completamente y que no se generan intermediarios tóxicos de importancia, con lo cual se confirma la factibilidad del tratamiento biológico para aceites dieléctricos.

  19. Signal correlations in biomass combustion. An information theoretic analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ruusunen, M.

    2013-09-01

    Increasing environmental and economic awareness are driving the development of combustion technologies to efficient biomass use and clean burning. To accomplish these goals, quantitative information about combustion variables is needed. However, for small-scale combustion units the existing monitoring methods are often expensive or complex. This study aimed to quantify correlations between flue gas temperatures and combustion variables, namely typical emission components, heat output, and efficiency. For this, data acquired from four small-scale combustion units and a large circulating fluidised bed boiler was studied. The fuel range varied from wood logs, wood chips, and wood pellets to biomass residue. Original signals and a defined set of their mathematical transformations were applied to data analysis. In order to evaluate the strength of the correlations, a multivariate distance measure based on information theory was derived. The analysis further assessed time-varying signal correlations and relative time delays. Ranking of the analysis results was based on the distance measure. The uniformity of the correlations in the different data sets was studied by comparing the 10-quantiles of the measured signal. The method was validated with two benchmark data sets. The flue gas temperatures and the combustion variables measured carried similar information. The strongest correlations were mainly linear with the transformed signal combinations and explicable by the combustion theory. Remarkably, the results showed uniformity of the correlations across the data sets with several signal transformations. This was also indicated by simulations using a linear model with constant structure to monitor carbon dioxide in flue gas. Acceptable performance was observed according to three validation criteria used to quantify modelling error in each data set. In general, the findings demonstrate that the presented signal transformations enable real-time approximation of the studied

  20. Manifold methods for methane combustion

    Energy Technology Data Exchange (ETDEWEB)

    Yang, B.; Pope, S.B. [Cornell Univ., Ithaca, NY (United States)

    1995-10-01

    Great progresses have been made in combustion research, especially, the computation of laminar flames and the probability density function (PDF) method in turbulent combustion. For one-dimensional laminar flames, by considering the transport mechanism, the detailed chemical kinetic mechanism and the interactions between these two basic processes, today it is a routine matter to calculate flame velocities, extinction, ignition, temperature, and species distributions from the governing equations. Results are in good agreement with those obtained for experiments. However, for turbulent combustion, because of the complexities of turbulent flow, chemical reactions, and the interaction between them, in the foreseeable future, it is impossible to calculate the combustion flow field by directly integrating the basic governing equations. So averaging and modeling are necessary in turbulent combustion studies. Averaging, on one hand, simplifies turbulent combustion calculations, on the other hand, it introduces the infamous closure problems, especially the closure problem with chemical reaction terms. Since in PDF calculations of turbulent combustion, the averages of the chemical reaction terms can be calculated, PDF methods overcome the closure problem with the reaction terms. It has been shown that the PDF method is a most promising method to calculate turbulent combustion. PDF methods have been successfully employed to calculate laboratory turbulent flames: they can predict phenomena such as super equilibrium radical levels, and local extinction. Because of these advantages, PDF methods are becoming used increasingly in industry combustor codes.

  1. Caracterización de los aceites crudo, neutro y decolorado de la pulpa y cascara de la fruta silvestre Paraqueiba sericea tulasne «Umarí».

    Directory of Open Access Journals (Sweden)

    Chasquibol Silva, Nancy A.

    1997-02-01

    Full Text Available Crude, neutro and blenched oil extracted from pulp and peel of jungle fruit Paraqueiba sericea tulasne «Umarí» were studied. The crude oil was extracted with hexane by the soxhlet method giving a 47.86% yield, a 31.72% yield in neutro oil and a 94.89% yield in blenched oil. Chemical and physical constants were determined. In addition, five methyl esters of fatty acids were quantitatively determined by GLC using DEGS as stationary phase. The results indicated that Umarí oil belongs to a not drying type with a high content of unsaturated fatty acids principaly oleic. The analytical values obtained confirm the convenience of using Umarí oil in food and cosmetic industries.

    Se estudian los aceites crudo, neutro y decolorado del fruto del Umarí. La extracción del aceite crudo se realizó mediante hexano por el método de soxhlet. El rendimiento fue de un 47,86% en aceite crudo, 31,72% en aceite neutro y 94,89% en aceite decolorado. Por métodos analíticos se determinaron constantes químicas y físicas. Además por cromatografía gas-líquido se cuantificaron cinco esteres metílicos de ácidos grasos, usando DEGS como fase estacionaria. Los resultados del estudio indican que el aceite de Umarí corresponde a un aceite del tipo no secante y con alto contenido de ácidos grasos insaturados principalmente oleico. Los índices analíticos obtenidos confirman la conveniencia de usar aceite de Umarí para aplicaciones en alimentos y cosmética.

  2. Caracterización del aceite microencapsulado de cardamomo (Elettaria cardamomum extraído por fluidos supercríticos a escala semi-industrial

    Directory of Open Access Journals (Sweden)

    María Eugenia Villada Ramírez

    2017-07-01

    Full Text Available Resumen El objetivo de este trabajo radicó en encontrar las condiciones óptimas para la obtención de un aceite de cardamomo, extraído por FSC a escala semi-industrial, con rendimientos iguales o superiores a los métodos convencionales, pero con calidad sensorial y técnica competitiva para los mercados internacionales, así como la producción de microcápsulas del aceite que permitieran incrementar la solubilidad, sin afectar las características sensoriales como aroma y sabor. Las semillas de cardamomo se obtuvieron en el municipio de Tarso, (Antioquia, Colombia, se acondicionaron para ser extraídas por FSC a escala de laboratorio a 200.400 bar y 50 °C, 60 °C, con tres réplicas al centro a 300 bar y 55 °C, de acuerdo a un diseño central compuesto y la optimización de los resultados por superficie de respuesta según el rendimiento (% y contenido de 1,8-cineol y acetato de α-terpenilo. Las condiciones finales (50 °C, 400 bar se escalaron a un extractor semi-industrial hasta obtener un aceite con un rendimiento de 8,54 ± 1,09% y una concentración de 1,8-cineol (28,37 ± 1,80% p/p y acetato de α-terpenilo (32,93 ± 1,24% p/p, analizados por GC-FID. La caracterización complementaria del aceite se encaminó al perfil sensorial y pruebas fisicoquímicas, con un resultado de atributos balanceados (herbal: 3,0, menta: 2,6, floral: 2,4 y cítrico: 2,3 e índice de color entre (+2 y +20. El aceite fue microencapsulado por secado por aspersión con una mezcla de goma arábiga, maltodextrina y almidón modificado (4/6, 1/6, 1/6 respectivamente. Se obtuvieron microcápsulas con un tamaño de partícula entre 12,2 y 25,78 µm y una distribución de la misma en solución acuosa de 13,18 µm, lo que permitió el aumento de la solubilidad del aceite en una matriz polar a temperatura ambiente.

  3. Markers of quality and genuineness of commercial extra virgin sacha inchi oils; Marcadores de la calidad y la genuinidad de aceites de sacha inchi extra virgen comerciales

    Energy Technology Data Exchange (ETDEWEB)

    Chasquibol, N.A.; Gomez-Coca, R.B.; Yacono, J.C.; Guinda, A.; Moreda, W.; Aguila, C.; Perez-Camino, M.C.

    2016-07-01

    This work tackles the study of the quality and authenticity of oils labeled and commercialized as extra virgin sacha inchi oil. Major and minor components as triglycerides, fatty acid methyl esters, tocopherols, sterols and hydrocarbons are determined as well as other physicochemical parameters (density, viscosity, acidity and peroxide value). The results showed that some of the commercialized oils do not fulfill the basic requirement established in the regulation such as the content of α-linolenic acid, higher than 44.7 or 55.0% in the cases of P. volubilis and P. huayllabambana, respectively. The calculated stigmasterol/campesterol ratio for genuine sacha inchi oils should be around 4, however not all commercial oils analyzed comply with this requirement. The presence of the flavons sesamin and sesamolin indicates the addition of compounds from sesame oils. Finally, some of the commercial oils showed to contain trans fatty acids although this was not accompanied by the sterene hydrocarbon presence. [Spanish] En este trabajo se aborda el estudio de la calidad y la genuinidad de los aceites etiquetados y comercializados como sacha inchi extra virgen. Se estudian los componentes mayoritarios como los triglicéridos y los ésteres metílicos de ácidos grasos, componentes menores insaponificables (tocoferoles, esteroles e hidrocarburos) así como otros parámetros fisicoquímicos (densidad, viscosidad, acidez, peróxidos y estabilidad). Los resultados mostraron que algunos de los aceites comercializados no cumplían con el requisito básico establecido en la normativa de tener un contenido en α-linolénico superior a 44,7 o 55,0% determinado para P. volubilis o P. huayllabambana respectivamente. La relación estigmasterol/campesterol medida en aceites de sacha inchi genuinos es de alrededor de 4, y no todos los aceites comerciales analizados cumplían con este requisito. La presencia de las flavonas sesamina y sesamolina indica la adición de compuestos procedentes

  4. Características químico-sensoriales de los aceites de oliva «Arbequina» obtenidos en distintas zonas de España

    Directory of Open Access Journals (Sweden)

    Touss, J.

    1997-12-01

    Full Text Available Within the quality virgin olive oils produced in Spain, Catalonia has two of the six currently existing Origin Denominations (Garrigues and Siurana. Their production of extra virgin oil proceeds of the «Arbequina» cultivar, approximately 8.000 tm, distributed between the CD «Garrigues», in Lleida (5.000 tm, and «Siurana» in Tarragona (3.000 tm. These oils are very appreciated at domestic as well as at international level because of their excellent taste. In the last years, this variety is being expanded in other regions of Spain (Andalusia, Aragon, etc. and over the worid (Argentina, France, etc.. The physico-chemical and sensory characteristics of «Arbequina» virgin olive oils produced are studied, mainly in Catalonia, Andalusia and Aragon. The obtained preliminary results indicate that some quality parameters of the «Arbequina» oil are variable, being cultivated in different environments, mainly certain fatty acids, polyphenols, oxidative stability and some sensory attributes of the oil.

    Dentro de los aceites de oliva vírgenes de calidad que se producen en España, Cataluña destaca por tener dos denominaciones de origen (Garrigues y Siurana de las seis actualmente existentes. La producción de aceite virgen extra de las mismas procede de la variedad «Arbequina», aproximadamente 8.000 tm, repartidas entre las D. O. «Garrigues», en Lleida (5.000 tm, y «Siurana» en Tarragona (3.000 tm. Estos aceites son muy apreciados tanto a nivel nacional como internacional por sus excelentes características organolépticas. En los últimos años, esta variedad se está extendiendo por España (Andalucía, Aragón, etc. y otros países del mundo (Argentina, Francia, etc.. Se estudian las características físico-químicas y sensoriales de los aceites de oliva vírgenes de la variedad «Arbequina» producidos, principalmente, en Cataluña, Andalucía y Aragón. Los resultados preliminares obtenidos indican que algunos parámetros del

  5. ANÁLISIS PRELIMINAR DEL TRATAMIENTO FISICOQUÍMICO Y BIOLÓGICO DEL ACEITE DIELÉCTRICO PRESENTE EN TIERRA FULLER

    Directory of Open Access Journals (Sweden)

    EDISON ALEXANDER AGUDELO

    2011-01-01

    Full Text Available Este estudio evalúa dos tecnologías: una físico-química y otra biológica, que buscan eliminar la contaminación por el aceite dieléctrico presente en la tierra Fuller, Buscando con ello gestionar de forma ambientalmente adecuada este residuo peligroso. Para la Tecnología físico-química, se usó hexano como solvente y se alcanzó de manera preliminar remociones del aceite dieléctrico del orden del 87% en la tierra Fuller tratada, con una relación tierra Fuller: solvente de 1:8 p/v, una velocidad de agitación de 100 rpm y un tiempo de contacto de 30 minutos. La calidad del aceite dieléctrico recuperado no es apta para su uso en equipos eléctricos, por su baja rigidez dieléctrica, baja densidad y color desfavorable. La tierra Fuller recuperada alcanzó una densidad aparente de 0.623 gr/ml, una densidad real de 2.231 gr/ml y una porosidad de 72.075 %, lo que indica al menos preliminarmente que dicha tierra está muycercana en sus características físicas a la tierra fuller limpia. Para la tecnología biológica se trató la tierra contaminada en un reactor biológico de tierra activada, evaluando la velocidad de agitación y el tiempo de degradación necesario para alcanzar niveles de contaminación adecuados que permitan disponer el residuo en un relleno sanitario convencional sin riesgo para la salud de los ecosistemas y el ser humano, esta fase aún se encuentra en experimentación y los resultados dependen del análisis cromatográfi co del aceite dieléctrico que permanece en la tierra Fuller tratada, en el cual se hará el seguimiento de 10 especies que son clave dentro de este producto, debido a su cantidad y/o toxicidad , falta comprobar la calidad química de la tierra fuller y del aceite dieléctrico recuperados en el tratamiento físico-químico, y validar el proceso biológico para degradar el aceite dieléctrico.

  6. Combustion & Laser Diagnostics Research Complex (CLDRC)

    Data.gov (United States)

    Federal Laboratory Consortium — Description: The Combustion and Laser Diagnostics Research Complex (CLRDC) supports the experimental and computational study of fundamental combustion phenomena to...

  7. Caracterización química y evaluación de la actividad antifúngica del aceite esencial foliar de Lippia alba contra Colletotrichum gloeosporioides

    Directory of Open Access Journals (Sweden)

    Alexander Pérez Cordero

    2017-07-01

    Full Text Available El objetivo de este estudio fue caracterizar y evaluar in vitro la eficiencia del aceite esencial foliar de Lippia alba contra Colletotrichum gloeosporioides. Se extrajo el aceite esencial a partir de las hojas mediante el método de hidrodestilación asistida por microondas (MWHD y se identificaron sus metabolitos mediante una cromatografía de gases acoplada a espectrometría de masas (GC/MS. La evaluación in vitro se realizó empleando 4 concentraciones del aceite esencial (500, 1000, 3000 y 10000 ppm diluidas en acetona; se utilizó un control positivo con Benomil 1 g/L, un control negativo con acetona y un testigo absoluto; la eficiencia del aceite se midió mediante el porcentaje de índice antifúngico (%I.A. El componente mayoritario en el aceite esencial fue el citral (34.62 a 40.03% y que el mayor %I.A se encontró a la concentración de 10000 ppm (97.8%, muy similar a la del Benomil (100%. Lo anterior demostraría la eficacia del aceite esencial de L. alba para controlar a C. gloeosporioides, y su posible uso como fungicida biológico.

  8. Efecto de diferentes métodos de extracción sobre el perfil de ácidos grasos en el aceite de aguacate (Persea americana Mill. var. Hass

    Directory of Open Access Journals (Sweden)

    José Alberto Ariza Ortega

    2011-12-01

    Full Text Available El objetivo de este estudio fue evaluar la posible formación de ácidos grasos trans (AGT en el aceite de aguacate, extraído con disolvente (hexano, con y sin calor, y por centrifugación. Para analizar el aceite se emplearon índices químicos, y para la identificación y cuantificación de los ácidos grasos se utilizó Espectroscopía de Infrarrojo con Transformada de Fourier (EITF, en la región media de 400 a 4000 cm-1 y cromatografía de gases. En los resultados del análisis por EITF se demostró que los tres aceites presentaron un pico definido en la región de 968 cm-1 que corresponde a los dobles enlaces trans. Los AGT se cuantificaron < 0,5 g/100 g de aceite, valores menores que el propuesto por The Danish Veterinary and Food Administration para considerar un aceite libre de AGT. De acuerdo con los índices químicos, el método que causó la mínima modificación en la calidad del aceite fue el de extracción por centrifugación.

  9. Efecto de diferentes métodos de extracción sobre el perfil de ácidos grasos en el aceite de aguacate (Persea americana Mill. var. Hass

    Directory of Open Access Journals (Sweden)

    Arturo Martínez Zavala

    2011-01-01

    Full Text Available El objetivo de este estudio fue evaluar la posible formación de ácidos grasos trans (AGT en el aceite de aguacate, extraído con disolvente (hexano, con y sin calor, y por centrifugación. Para analizar el aceite se emplearon índices químicos, y para la identificación y cuantificación de los ácidos grasos se utilizó Espectroscopía de Infrarrojo con Transformada de Fourier (EITF, en la región media de 400 a 4000 cm E-1 y cromatografía de gases. En los resultados del análisis por EITF se demostró que los tres aceites presentaron un pico definido en la región de 968 cm E-1 que corresponde a los dobles enlaces trans. Los AGT se cuantificaron < 0,5 g/100 g de aceite, valores menores que el propuesto por The Danish Veterinary and Food Administration para considerar un aceite libre de AGT. De acuerdo con los índices químicos, el método que causó la mínima modificación en la calidad del aceite fue el de extracción por centrifugación.

  10. Combustion instability control in the model of combustion chamber

    International Nuclear Information System (INIS)

    Akhmadullin, A N; Ahmethanov, E N; Iovleva, O V; Mitrofanov, G A

    2013-01-01

    An experimental study of the influence of external periodic perturbations on the instability of the combustion chamber in a pulsating combustion. As an external periodic disturbances were used sound waves emitted by the electrodynamics. The purpose of the study was to determine the possibility of using the method of external periodic perturbation to control the combustion instability. The study was conducted on a specially created model of the combustion chamber with a swirl burner in the frequency range from 100 to 1400 Hz. The study found that the method of external periodic perturbations may be used to control combustion instability. Depending on the frequency of the external periodic perturbation is observed as an increase and decrease in the amplitude of the oscillations in the combustion chamber. These effects are due to the mechanisms of synchronous and asynchronous action. External periodic disturbance generated in the path feeding the gaseous fuel, showing the high efficiency of the method of management in terms of energy costs. Power required to initiate periodic disturbances (50 W) is significantly smaller than the thermal capacity of the combustion chamber (100 kW)

  11. Balance of natural radionuclides in the brown coal based power generation and harmlessness of the residues and side product utilization

    International Nuclear Information System (INIS)

    Schulz, Hartmut; Kunze, Christian; Hummrich, Holger

    2017-01-01

    During brown coal combustion a partial enrichment of natural radionuclides occurs in different residues. Residues and side product from brown coal based power generation are used in different ways, for example filter ashes and gypsum from flue gas desulfurization facilities are used in the construction materials fabrication and slags for road construction. Detailed measurement and accounting of radionuclides in the mass throughputs in coal combustion power plants have shown that the utilized gypsum and filter ashes are harmless in radiologic aspects.

  12. Space Station Freedom combustion research

    Science.gov (United States)

    Faeth, G. M.

    1992-01-01

    Extended operations in microgravity, on board spacecraft like Space Station Freedom, provide both unusual opportunities and unusual challenges for combustion science. On the one hand, eliminating the intrusion of buoyancy provides a valuable new perspective for fundamental studies of combustion phenomena. On the other hand, however, the absence of buoyancy creates new hazards of fires and explosions that must be understood to assure safe manned space activities. These considerations - and the relevance of combustion science to problems of pollutants, energy utilization, waste incineration, power and propulsion systems, and fire and explosion hazards, among others - provide strong motivation for microgravity combustion research. The intrusion of buoyancy is a greater impediment to fundamental combustion studies than to most other areas of science. Combustion intrinsically heats gases with the resulting buoyant motion at normal gravity either preventing or vastly complicating measurements. Perversely, this limitation is most evident for fundamental laboratory experiments; few practical combustion phenomena are significantly affected by buoyancy. Thus, we have never observed the most fundamental combustion phenomena - laminar premixed and diffusion flames, heterogeneous flames of particles and surfaces, low-speed turbulent flames, etc. - without substantial buoyant disturbances. This precludes rational merging of theory, where buoyancy is of little interest, and experiments, that always are contaminated by buoyancy, which is the traditional path for developing most areas of science. The current microgravity combustion program seeks to rectify this deficiency using both ground-based and space-based facilities, with experiments involving space-based facilities including: laminar premixed flames, soot processes in laminar jet diffusion flames, structure of laminar and turbulent jet diffusion flames, solid surface combustion, one-dimensional smoldering, ignition and flame

  13. Aprovechamiento de las oleinas residuales procedentes del proceso de refinado de los aceites vegetales comestibles, para la fabricación de biodiesel

    Directory of Open Access Journals (Sweden)

    Álvarez Mateos, P.

    2003-06-01

    Full Text Available A procedure to obtain Biodiesel from “Oleinas” is studied. Biodiesel is a suitable product to replace diesel oil currently used to power the Diesel engines. It consists of a mixture of methyl esters of the fatty acids presents as triglycerides in vegetables oils (olive, sunflower, soya, rape oils. As a result of the refining of these oils for their use as food, a waste product is formed, the “oleinas” (acidulated soapstock. The oleinas consist of a mixture of triglycerides and free fatty acids, the latter amounting to 50% or more of the mixture and are subject to a fluctuating market, therefore it exist at times a problem for their disposal. In our research work we have tried to obtain biodiesel from oleinas. The process resulting from our experimental work is as follows: 1. Sterification of the free fatty acids with methanol, by acid catalysis, centrifuging the reaction product and removal of the acid-methanol phase. Drying of the latter. At this stage we have a product containing about 70% of methyl esters. 2. Transesterification of the triglycerides present in the sterified product with methanol by alkaline catalysis, washing the reaction product with a water methanol solution. Centrifuging and removal of the water-methanol phase. At this stage a biodiesel product is obtained containing about 90% of methyl esters. 3. Fractional vacuum distillation of the 90% biodiesel gives a final product with a methyl esters content higher than 98%.Se estudia un procedimiento para la obtención de Biodiesel a partir de las “Oleínas”. Biodiesel es un producto capaz de sustituir al combustible Diesel ordinario que se obtiene del petróleo y que consiste en una mezcla de ésteres metílicos de ácidos grasos. Las oleínas son unos residuos que resultan del proceso de refinado de aceites vegetales para su uso alimentario y se componen de una mezcla de triglicéridos y ácidos grasos libres, con un contenido de estos últimos

  14. Diseño de un reactor de transesterificación para la obtención de biodiesel a partir de aceites vegetales

    OpenAIRE

    MARSET GIMENO, DAVID

    2016-01-01

    [ES] En este proyecto se pretende que el alumno realice el diseño, montaje y puesta a punto un reactor de transesterificación de laboratorio para la obtención de biodiesel a partir de aceites vegetales, utilizando catálisis básica homogénea. Paralelamente se definirán las técnicas analíticas a emplear para el control de la calidad de los aceites de partida y el seguimiento de los productos de reacción. A partir de los resultados experimentales se realizará el diseño y estimación económica...

  15. Aceite de girasol, semillas y plantas con distribución modificada de ácidos grasos en la molécula de triacil-glicerol

    OpenAIRE

    Garcés Mancheño, Rafael; Martínez-Force, Enrique

    2003-01-01

    El objeto de la presente invención es un aceite de girasol que se obtiene directamente de la semilla de girasol con de 12-40,8% de ácido esteárico calculado en relación al contenido total de ácidos grasos y con una distribución de ácidos grasos modificada entre las posiciones sn-1 y sn-3 de la molécula de triacilglicerol (TAG) comparado con el aceite obtenido del tipo silvestre de semillas de girasol. La invención también se refiere a una planta de girasol y a semillas que contien...

  16. Catalytic Combustion of Gasified Waste

    Energy Technology Data Exchange (ETDEWEB)

    Kusar, Henrik

    2003-09-01

    This thesis concerns catalytic combustion for gas turbine application using a low heating-value (LHV) gas, derived from gasified waste. The main research in catalytic combustion focuses on methane as fuel, but an increasing interest is directed towards catalytic combustion of LHV fuels. This thesis shows that it is possible to catalytically combust a LHV gas and to oxidize fuel-bound nitrogen (NH{sub 3}) directly into N{sub 2} without forming NO{sub x} The first part of the thesis gives a background to the system. It defines waste, shortly describes gasification and more thoroughly catalytic combustion. The second part of the present thesis, paper I, concerns the development and testing of potential catalysts for catalytic combustion of LHV gases. The objective of this work was to investigate the possibility to use a stable metal oxide instead of noble metals as ignition catalyst and at the same time reduce the formation of NO{sub x} In paper II pilot-scale tests were carried out to prove the potential of catalytic combustion using real gasified waste and to compare with the results obtained in laboratory scale using a synthetic gas simulating gasified waste. In paper III, selective catalytic oxidation for decreasing the NO{sub x} formation from fuel-bound nitrogen was examined using two different approaches: fuel-lean and fuel-rich conditions. Finally, the last part of the thesis deals with deactivation of catalysts. The various deactivation processes which may affect high-temperature catalytic combustion are reviewed in paper IV. In paper V the poisoning effect of low amounts of sulfur was studied; various metal oxides as well as supported palladium and platinum catalysts were used as catalysts for combustion of a synthetic gas. In conclusion, with the results obtained in this thesis it would be possible to compose a working catalytic system for gas turbine application using a LHV gas.

  17. Producer for vegetal combustibles for internal-combustion motors

    Energy Technology Data Exchange (ETDEWEB)

    1943-12-28

    A producer is described for internal-combustion motors fed with wood or agricultural byproducts characterized by the fact that its full operation is independent of the degree of wetness of the material used.

  18. Reducing emissions from diesel combustion

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper contains information dealing with engine design to reduce emissions and improve or maintain fuel economy. Topics include: Observation of High Pressure Fuel Spray with Laser Light Sheet Method; Determination of Engine Cylinder Pressures from Crankshaft Speed Fluctuations; Combustion Similarity for Different Size Diesel Engines: Theoretical Prediction and Experimental Results; Prediction of Diesel Engine Particulate Emission During Transient Cycles; Characteristics and Combustibility of Particulate Matter; Dual-Fuel Diesel Engine Using Butane; Measurement of Flame Temperature Distribution in D.I. Diesel Engine with High Pressure Fuel Injection: and Combustion in a Small DI Diesel Engine at Starting

  19. Microorganismos con capacidad degradativa de aceites lubricantes usados, aislados de estratos superficiales de suelos contaminados y optimización de condiciones de crcimiento. Ayacucho 2009

    OpenAIRE

    Palomino Felices, Sonia Haydeé

    2014-01-01

    La biorremediación, consiste principalmente en el uso de los organismos nativos (bacterias, hongos, plantas) para descomponer o degradar sustancias peligrosas convirtiéndolas en sustancias de caracteres menos tóxicos o inocuos para el ambiente y la salud humana. La investigación tuvo los siguientes objetivos: a) utilizar los microorganismos aislados de suelos contaminados con hidrocarburos para degradar "aceite lubricante usado" en suelos de experimentación en condiciones de laboratorio, b) e...

  20. PIGMENTACIÓN, CRECIMIENTO Y SUPERVIVENCIA DE CRÍAS CARPA KOI (CYPRINUS CARPIO VAR. HAEMATOPTERUS ALIMENTADAS CON DIETAS CON INCLUSIONES DE ACEITE DE LANGOSTILLA ROJA (PLEURONCODES PLANIPES

    Directory of Open Access Journals (Sweden)

    Gloria L. Gil R.

    2015-01-01

    Full Text Available En este estudio se evaluó el efecto de la inclusión de aceite de langostilla roja (Pleuroncodes planipes sobre el crecimiento, supervivencia y pigmentación del tegumento de crías de carpa koi (Cyprinus carpio var. haematopterus. El estudio consistió en tres experimentos: experimento 1, con fotoperiodo de 4 h L / 20 h O y aguas claras; experimento 2, con fotoperiodo 12 h L/ 12 h O y aguas claras, y, experimento 3, cuyo fotoperiodo fue de 12 h L /12 O y aguas con algas. En estos experimentos, dos variedades de crías de carpa koi -naranjas y con manchas oscuras- fueron alimentadas con dietas adicionadas con aceite de langostilla a diferentes porcentajes de inclusión (0, 1, 2 y 3 %, con el 5% de alimento con relación a la biomasa de cada unidad experimental. Al final de cada uno de los experimentos se tomaron fotografías de los organismos y se analizó la coloración con el modelo de matiz-saturación-brillantez de cuatro regiones anatómicas en ambas variedades de crías y en los experimentos 1 y 2 se evaluaron parámetros biológicos: supervivencia, ganancia en longitud y en peso, y porcentaje de incremento en peso y en longitud. Las dietas adicionadas con aceite de langostilla roja no fueron rechazadas por los organismos, y no se observaron efectos negativos en las variables evaluadas. En general, la inclusión de aceite influyó en la pigmentación de las crías de color naranja y en el crecimiento y la coloración de los organismos con manchas oscuras, particularmente cuando el fotoperiodo fue de 12 L/ 12 O.

  1. Composición química y actividad antibacteriana del aceite esencial del Origanum vulgare (orégano

    Directory of Open Access Journals (Sweden)

    Emilia Albado Plaus

    2001-01-01

    Full Text Available Objetivo: Determinar la actividad antimicrobiano en el aceite esencial (Carvacrol del Origanum vulgare. Material y métodos: El aceite esencial se obtuvo por destilación por arrastre con vapor de agua, a partir de las hojas y flores desecadas de O. vulgare; se determinó la gravedad especifica con un pinnómetro y el índice de refracción con refractómetro de Abbc; la composición química se evaluó mediante cromatografía de gas con detector de masa (GL-SM. La actividad antimicrobiana del aceite de O. vulgare se realizó por el método semicuantitativo de incorporación y de disco difusión en agar. Resultados: La densidad especifica del producto resultó 0.9234 a 20°C y el índice de refracción 1.4774; el cromatograma mostró un contenido de 9% de Carvacrol, 12.19% de Terpineol, 6.86% de P-cimeno y la presencia de otros compuesto relacionados metabolicamente con los tres antes citados. Las bacterias gram-negativas: Escherichia coli, Pseudomona aeruginosa, Salmonella tiphymurium, Salmonella cholerae suis y Vibrio cholerae y las bacterias gram-positivas: Staphylococcus aureus y Bacillus cereus, mostraron diferentes grados de sensibilidad. De los microorganismos evaluados solo pseudomonas aeruginosa mostró resistencia. Conclusión: El aceite esencial posee actividad microbiana contra todas las bacterias evaluadas, excepto antes para P. aeruginosa.(Rev Med Hered 2001; 12: 16-19 .

  2. Efecto del extracto de romero (rosmarinus officinalis) y el proceso de fritura sobre la calidad y vida útil de aceite y productos pre-fritos

    OpenAIRE

    Teruel Gutierrez, María del Rocío

    2015-01-01

    La presente tesis tiene como objetivo principal mejorar la calidad y estabilidad del medio y los productos de fritura. Con este propósito han sido realizados cuatro ensayos experimentales. El primer y segundo experimental tuvieron como objetivos caracterizar diferentes extractos comerciales de romero, y posteriormente, evaluar el efecto de los mismos en diferentes matrices alimentarias (nuggets de pollo y el aceite de fritura). Para lo cual se llevaron a cabo los siguientes métodos analít...

  3. Evaluation of the use of a vegetable oil in distribution transformers Evaluación del uso de un aceite vegetal en transformadores de distribución

    Directory of Open Access Journals (Sweden)

    Diego Fernando-Navas

    2012-08-01

    Full Text Available Since the start of transformers immersed in refrigerating liquid, the fluid traditionally used has been mineral oil. However, in recent decades, efforts have been joined in the search for alternatives with a lower environmental impact and which also satisfy the technical requirements of insulation and refrigeration in the transformers. Currently, insulating vegetable oils are available in the market, which may have lower environmental impact during their use and final disposition; nevertheless, their high cost and short time of use have limited their massive application. This work presents the thermal behavior evaluation of two distribution transformers at different powers immersed in dielectric vegetable oil, comparing their performance with that of two constructively equal transformers immersed in mineral oil. The results obtained reveal that the transformers comply with the requirements of existing standards.Desde los inicios de los transformadores inmersos en líquido refrigerante, el fluido empleado por tradición ha sido el aceite de origen mineral. Sin embargo, en las últimas décadas se han unido esfuerzos en la búsqueda de alternativas que tengan un menor impacto en el medio ambiente y que a su vez satisfagan los requerimientos técnicos de aislamiento y refrigeración en los transformadores. Actualmente se encuentran en el mercado aceites aislantes de origen vegetal que pueden tener un menor impacto ambiental durante su uso y disposición final; no obstante, su elevado costo y su poco tiempo de uso han limitado su aplicación masiva. En este trabajo se presenta la evaluación del comportamiento térmico de dos transformadores de distribución de diferente potencia inmersos en aceite dieléctrico de origen vegetal y se compara su desempeño con el de dos transformadores constructivamente iguales inmersos en aceite mineral. Los resultados obtenidos revelan que los transformadores cumplen con los requerimientos de la normatividad

  4. Análisis estratégico del sector envasador de aceite de oliva en España. Recomendaciones para el subsector cooperativo

    Directory of Open Access Journals (Sweden)

    Yolanda Pelayo Díaz

    2003-01-01

    Full Text Available Se propone, a partir de un análisis dafo en el sector envasador de aceite de oliva en España, un posicionamiento producto-mercado para el subsector productor cooperativo, con el objeto de encontrar estrategias para que éste participe en el sistema agroalimentario no sólo en la fase de producción, sino también en las actividades comercializadoras orientadas al consumidor final.

  5. The effects of process technology on the physicochemical properties of peony seed oil; Efectos de la tecnología de procesos sobre las propiedades fisicoquímicas del aceite de peonía

    Energy Technology Data Exchange (ETDEWEB)

    Qu, J.; Zhang, F.; Thakur, K.; Shi, J.J.; Zhang, J.G.; Faisal, S.; Wei, Z.J.

    2017-07-01

    Peony seed oils (PSOs) were prepared using supercritical CO2 (SC) and compared with soxhlet extraction (SE) and mechanical screw press extraction (SPE) methods. The fatty acid compositions of the oils were determined, and the physicochemical properties of the oils, including free radical-scavenging activity, α-amylase and α-glucosidase inhibition, thermal and rheological properties were evaluated. The unsaturated fatty acids in the SE oils were higher than SC and SPE oils due to the higher percentage of olefinic, allylic methylene and allylic methine protons in the SE oils. The SPE oils also displayed the highest DPPH and ABTS+ radical scavenging activity at the tested concentrations. However, the SE oils showed stronger inhibitory effects on α-amylase and α-glucosidase enzymes under in vitro conditions when compared with the other oil samples. The three oils had similar melting and crystalline point due to similar contents of fatty acids (FAs). The SC oils had a lower Ea than the others. [Spanish] Se prepararon aceites de semillas de peonia (PSOs) utilizando CO2 supercrítico (SC) y se compararon con los métodos de extracción en soxhlet (SE) y de extracción mecánica de tornillos (SPE). Se determinaron las composiciones en ácidos grasos y se evaluaron las propiedades fisicoquímicas de los aceites incluyendo la actividad de eliminación de radicales libres, la inhibición de α-amilasa y α-glucosidasa, las propiedades térmicas y reológicas. Los ácidos grasos insaturados en los aceites SE fueron más altos que los aceites SC y SPE debido al mayor porcentaje de protones olefínicos, metileno alílico y metino alílico en los aceites SE. Los aceites SPE también mostraron una actividad de eliminación de radicales DPPH y ABTS+ más alta a las concentraciones ensayadas. Sin embargo, los aceites SE mostraron efectos inhibidores más fuertes sobre las enzimas α-amilasa y α-glucosidasa bajo condiciones in vitro cuando se compararon con las otras muestras de

  6. ACTIVIDAD ANTIMICÓTICA DEL ACEITE ESENCIAL DE LAS HOJAS DE Minthostachys mollis (MUÑA COMPARADO CON EL FLUCONAZOL EN CULTIVO DE Candida albicans

    Directory of Open Access Journals (Sweden)

    Katherine M Alcalá-Marcos

    2011-01-01

    Full Text Available Objetivo.- Demostrar el efecto antimicótico del aceite esencial de las hojas de Minthostachys mollis (muña en comparación con el Fluconazol en cultivo de Candida albicans. Materiales y Método.- Estudio experimental. El efecto antimicótico se estudió midiendo 80 halos de inhibición distribuidos en 5 grupos mediante el método Kirby-Bauer. Se utilizó una cepa clínica de Candida albicans. Los grupos de estudio fueron grupo muña 25% (GM25%, grupo muña 50% (GM50%, grupo muña 100% (GM100%, un grupo control positivo (Fluconazol, y un grupo control negativo (aceite mineral. El análisis estadístico se realizó mediante la Prueba de Kruskal-Wallis y el Test de Dunn usando el paquete SPSS v.17.0. Se consideró un nivel de significancia 0,05.Conclusión.- El aceite esencial de las hojas de Minthostachys mollis (al 100% tuvo mayor efecto contra la Candida albicans que el Fluconazol; además, el efecto antimicótico del Fluconazol fue mayor que la Minthostachys mollis al 25%, y fue el mismo que la Minthostachys mollis al 50%.

  7. Actividad antimicótica del aceite esencial de las hojas de Minthostachys mollis (muña comparado con el Fluconazol en cultivo de Candida albicans

    Directory of Open Access Journals (Sweden)

    Katherine M Alcalá-Marcos

    2012-09-01

    Full Text Available Objetivo.- Demostrar el efecto antimicótico del aceite esencial de las hojas de Minthostachys mollis (muña en comparación con el Fluconazol en cultivo de Candida albicans. Materiales y Método.- Estudio experimental. El efecto antimicótico se estudió midiendo 80 halos de inhibición distribuidos en 5 grupos mediante el método Kirby-Bauer. Se utilizó una cepa clínica de Candida albicans. Los grupos de estudio fueron grupo muña 25% (GM25%, grupo muña 50% (GM50%, grupo muña 100% (GM100%, un grupo control positivo (Fluconazol, y un grupo control negativo (aceite mineral. El análisis estadístico se realizó mediante la Prueba de Kruskal-Wallis y el Test de Dunn usando el paquete SPSS v.17.0. Se consideró un nivel de significancia  0,05.Conclusión.- El aceite esencial de las hojas de Minthostachys mollis (al 100% tuvo mayor efecto contra la Candida albicans que el Fluconazol; además, el efecto antimicótico del Fluconazol fue mayor que la Minthostachys mollis al 25%, y fue el mismo que la Minthostachys mollis al 50%.

  8. Procesado acuoso de soja con tecnología enzimática: extracción de aceite y producción de aislados

    Directory of Open Access Journals (Sweden)

    Domínguez, H.

    1995-02-01

    Full Text Available An enzymatic treatment was incorporated before the alkaline extraction during the aqueous processing of soya beans for oil and protein. The degradation on the plant cell wall structure by the enzymatic action, enhances the oil extractability by 10% of the potential extractable oil. No significant effect on the protein extractability was detected, although this effect was probably masked by the alkaline extraction. After the aqueous extraction, 30% of active enzyme was eliminated in the whey. This can be recovered and reutilized in the next stage.

    Se ha incorporado una etapa de tratamiento enzimático previa a la extracción acuosa en condiciones alcalinas durante el procesado para obtención de aceite y proteína de soja. La degradación de la estructura de la pared vegetal, causada por el ataque enzimático, aumenta la extractabilidad del aceite en un 10% respecto al aceite total extraíble. No se apreció efecto sobre el rendimiento de proteína debido posiblemente a que la posterior extracción a pH 9 inhibe los efectos de la acción enzimática. Tras la realización del proceso de extracción acuoso, se elimina en el suero un 30% de enzima activa, que puede ser reutilizada en el proceso.

  9. Costos de producción en el proceso de extracción de aceite de palma: Estudio de un caso

    Directory of Open Access Journals (Sweden)

    Rosana Meleán Romero

    2014-01-01

    Full Text Available El objetivo de esta investigación es analizar los costos de producción del proceso de extracción de aceite de palma, basados en el estudio de una de las empresas que conforman el sector palmicultor, ubicada en el estado Zulia-Venezuela. Se cataloga como analítica-proyectiva, de campo y transeccional; apoyada en material bibliográfico y otros documentos de interés necesarios para construir un instrumento de recolección de información (cuestionario, aplicado a informantes clave de una empresa del sector; se analiza la información recopilada, obteniendo como resultados que los costos se manejan de manera tradicional y dadas las complejidades del proceso que desarrolla la empresa, impide la determinación exacta del costo de los productos que elaboran: aceite rojo, aceite de palmiste y harina de palmiste. En función de ello, se propone una metodología híbrida de costeo que combina características del sistema de acumulación de costos por procesos y del costeo basado en actividades. Se concluye que una vez aplicada la propuesta realizada, la empresa podrá sistematizar sus costos de producción, obtener el costo unitario de los productos elaborados, además de encaminar el diseño de un sistema de información de costos ajustado a sus necesidades

  10. Caracterización del aceite de semilla de uva extraído con dióxido de carbono supercrítico

    Directory of Open Access Journals (Sweden)

    Molero Gómez, A.

    1995-02-01

    Full Text Available In this work the quality of grape seed oil obtained by extraction with supercritical carbon dioxide was studied. At the optimun operating conditions (313 K and 25 MPa, the yield of supercritical extraction is similar to the conventional extraction by liquid solvent, but the quality of the grape seed oil extracted by supercritical carbon dioxide is higher.
    Furthermore, supercritical extraction could be more economical than liquid extraction because the solvent removal by distillation is not necessary and several steps of the subsequent oil refining process can be eliminated.

    En este trabajo se realiza un estudio de la calidad del aceite de semillas de uva obtenido por extracción con dióxido de carbono supercrítico. En las condiciones operativas óptimas del proceso (313 K y 25 MPa el rendimiento de la extracción supercrítica es similar al de la extracción con disolventes líquidos, pero la calidad del aceite es muy superior.
    En consecuencia, el proceso supercrítico resulta competitivo con el convencional al reducir las etapas de refinado del aceite y eliminar la destilación del disolvente, las más costosas desde el punto de vista energético.

  11. Caracterización de los aceites de refrigeración utilizados en motocompresores herméticos que trabajan con el gas refrigerante LB-12

    Directory of Open Access Journals (Sweden)

    Celestino Oro Ortiz

    2011-03-01

    Full Text Available El objetivo de este trabajo va dirigido a conocer las principales propiedades de los aceites de refrigeración de formulaciónnacional y extranjera concebidos para los sistemas que trabajan con el refrigerante R-12 y en la actualidad se utilizancon el gas refrigerante LB-12. Se realizó un análisis de laboratorio a los aceites estudiados según las normas de laASTM para los productos derivados del petróleo. Los resultados de este trabajo son de interés para la correctaselección del aceite de refrigeración atendiendo al modelo de compresor, refrigerante utilizado y condiciones deexplotación.  The use of the hydrocarbons as refrigerants in actuality have been a great diffusion in the hermetic motocompressorsof domestic refrigerators and other, in substitution of the R-12 refrigerant which result harmful to the ozone layer. Theobjective of this research was to know the principal properties of the refrigeration oils of national and foreign formulationmarketed for the refrigeration systems that work with the refrigerant R-12 and in the nowadays are using the refrigerantgas LB-12. In this work was made laboratories analysis to the oil using the ASTM norms for the oil products. Theresults of this work are interesting for the suitable selection of the refrigeration oil it must be taken into accountmotocompressor model, refrigerant used, and exploitation conditions.

  12. SCR at bio fuel combustion

    International Nuclear Information System (INIS)

    Andersson, Christer; Odenbrand, I.; Andersson, L.H.

    1998-10-01

    In this project the cause for and the extent of catalyst deactivation has been investigated when using 100 % wood as fuel. The trend of deactivation has been studied as a function of the flue gas temperature, the type of catalyst and the type of combustion technique used. The field tests have been performed in the CFB boiler in Norrkoeping, firing forest residues, and in the boiler in Jordbro, firing pulverized wood (PC). Samples of four different commercial catalyst types have been exposed to flue gas in a test rig connected to the convection section of the boiler. The samples have been analysed at even time intervals. The results after 2 100 hours show a large difference in deactivation trend between the two plants; when using a conventional honeycomb catalyst 80 % of the original activity remains in the CFB boiler but only 20 % remains in the PC boiler. The deactivation in the CFB boiler is about 3 - 4 times faster than what is expected for a conservative design for a coal fired boiler. The results show that the general deactivation trend is similar for the plate and the honeycomb catalyst types. With a catalyst optimised for bio fuels the deactivation rate was about 2/3 compared with a conventional catalyst. At an operating temperature of 315 deg C the deactivation was not as rapid as at 370 deg C. The amount of easily dissolved potassium increases on the surface of the catalyst, especially in the PC boiler, and this is probably the reason for the deactivation. The total amount of potassium in the flue gas is about 5 times higher in the CFB boiler compared with the PC boiler. This indicates that only a certain form of potassium attacks the catalyst and that the total alkali content of the fuel is not a good indicator of the deactivation tendency. The potassium on the catalyst dissolves easily in both water and sulphuric acid. A wash of deactivated catalyst samples with water resulted in higher activity than for the fresh samples if the washing was supplemented

  13. Computational Modeling of Turbulent Spray Combustion

    NARCIS (Netherlands)

    Ma, L.

    2016-01-01

    The objective of the research presented in this thesis is development and validation of predictive models or modeling approaches of liquid fuel combustion (spray combustion) in hot-diluted environments, known as flameless combustion or MILD combustion. The goal is to combine good physical insight,

  14. Measures for a quality combustion (combustion chamber exit and downstream); Mesures pour une combustion de qualite (sortie de chambre de combustion et en aval)

    Energy Technology Data Exchange (ETDEWEB)

    Epinat, G. [APAVE Lyonnaise, 69 (France)

    1996-12-31

    After a review of the different pollutants related to the various types of stationary and mobile combustion processes (stoichiometric, reducing and oxidizing combustion), measures and analyses than may be used to ensure the quality and efficiency of combustion processes are reviewed: opacimeters, UV analyzers, etc. The regulation and control equipment for combustion systems are then listed, according to the generator capacity level

  15. Fuels and Combustion | Transportation Research | NREL

    Science.gov (United States)

    Fuels and Combustion Fuels and Combustion This is the March 2015 issue of the Transportation and , combustion strategy, and engine design hold the potential to maximize vehicle energy efficiency and performance of low-carbon fuels in internal combustion engines with a whole-systems approach to fuel chemistry

  16. Evaluación fisico-química de la semilla y del aceite de corozo ( Acrocomia aculeata Jacq.

    Directory of Open Access Journals (Sweden)

    Medina, Carlos

    2005-12-01

    Full Text Available In this research, physicochemical characteristics of the seed and seed oil of corozo ( Acrocomia aculeata Jacq., a wild palm from Central and South America , were evaluated. Seeds obtained from mature fruits from “El Chaparro” town, Anzoategui state, Venezuela, harvested in March 2003, were decorticated; the endospermus was transformed to meal by means of grinding and then using a sieve (425 µm, and its oil was extracted with n-hexane. The whole seed showed an average weight of 9.67 ± 0.32 (PEl objetivo de esta investigación fue evaluar algunas características físicas y químicas de la semilla y del aceite crudo extraído de la semilla del fruto de corozo ( Acrocomia aculeata Jacq., una palmera silvestre distribuida en Centroamérica y Sudamérica. A un lote se semillas obtenidas de frutos maduros procedentes de la población de “El Chaparro”, estado Anzoátegui, Venezuela, cosechados en Marzo 2003, se le separó el pericarpio y el endospermo. El endospermo fue transformado en harina, mediante molienda y tamizado (apertura 425 μm, y a ésta se le extrajo el aceite con n-hexano. A la semilla entera se le determinó la masa promedio (9,67 ± 0,32; P<0,05 y la proporción de pericarpio (75,39 % y endospermo (24,61 %. A la harina del endospermo de le determinó la composición proximal, presentando niveles importantes de grasa (53,13 %, proteína (13,75 % y fibra cruda (25,82 %. El aceite crudo de corozo presentó baja acidez libre (0,40 %, expresada como ácido oleico y alta resistencia a la oxidación (no se detectó peróxidos y el índice de estabilidad OSI fue de 100 h; sus índices de yodo y saponificación fueron 29,87 cg I/g y 205 mg KOH/g, respectivamente. La composición en ácidos grasos, determinada mediante cromatografía de gas, mostró mayor proporción de ácidos saturados (79,6 %, siendo el ácido láurico el de mayor concentración. La semilla de corozo es un recurso oleaginoso que puede ser útil

  17. Combustion modeling in waste tanks

    International Nuclear Information System (INIS)

    Mueller, C.; Unal, C.; Travis, J.R.; Forschungszentrum Karlsruhe

    1997-01-01

    This paper has two objectives. The first one is to repeat previous simulations of release and combustion of flammable gases in tank SY-101 at the Hanford reservation with the recently developed code GASFLOW-II. The GASFLOW-II results are compared with the results obtained with the HMS/TRAC code and show good agreement, especially for non-combustion cases. For combustion GASFLOW-II predicts a steeper pressure rise than HMS/TRAC. The second objective is to describe a so-called induction parameter model which was developed and implemented into GASFLOW-II and reassess previous calculations of Bureau of Mines experiments for hydrogen-air combustion. The pressure time history improves compared with the one-step model, and the time rate of pressure change is much closer to the experimental data

  18. Environmental sensing and combustion diagnostics

    International Nuclear Information System (INIS)

    Santoleri, J.J.

    1991-01-01

    This book contains proceedings of Environmental Sensing and Combustion Diagnostics. Topics covered include: Incineration Systems Applications, Permitting, And Monitoring Overview; Infrared Techniques Applied to Incineration Systems; Continuous Emission Monitors; Analyzers and Sensors for Process Control And Environmental Monitoring

  19. Sodium nitrate combustion limit tests

    International Nuclear Information System (INIS)

    Beitel, G.A.

    1976-04-01

    Sodium nitrate is a powerful solid oxidant. Energetically, it is capable of exothermically oxidizing almost any organic material. Rate-controlling variables such as temperature, concentration of oxidant, concentration of fuel, thermal conductivity, moisture content, size, and pressure severely limit the possibility of a self-supported exothermic reaction (combustion). The tests reported in this document were conducted on one-gram samples at atmospheric pressure. Below 380 0 C, NaNO 3 was stable and did not support combustion. At moisture concentrations above 22 wt percent, exothermic reactions did not propagate in even the most energetic and reactive compositions. Fresh resin and paraffin were too volatile to enable a NaNO 2 -supported combustion process to propagate. Concentrations of NaNO 3 above 95 wt percent or below 35 wt percent did not react with enough energy release to support combustion. The influence of sample size and confining pressure, both important factors, was not investigated in this study

  20. 75 FR 3881 - Combustible Dust

    Science.gov (United States)

    2010-01-25

    ..., rubber, drugs, dried blood, dyes, certain textiles, and metals (such as aluminum and magnesium..., furniture manufacturing, metal processing, fabricated metal products and machinery manufacturing, pesticide... standard that will comprehensively address the fire and explosion hazards of combustible dust. The Agency...

  1. Modelling of turbulent combustion in the blast furnace raceway

    Energy Technology Data Exchange (ETDEWEB)

    Karvinen, R; Maekiranta, R [Tampere Univ. (Finland). Energy and Process Engineering

    1997-12-31

    The phenomena concerning coke-gas -suspension and simultaneous combustion of solid coke particles and residual fuel oil in a blast furnace raceway are modelled. The flow field of suspension is predicted by using the two fluid model, which is based on the Eulerian method, in the Phoenics code. The standard k-e -model of turbulence is used. Pyrolysis of oil droplets is calculated with the own coded subroutine, which is based on the Lagrangian approach. Gas phase reaction rate is assumed to be controlled by chemical kinetics. Radiative heat transfer is calculated by using the six-flux method. Heterogenous surface reactions are used for the coke particles. Calculations without coke combustion show that due to a poor mixing in the hot blast, pyrolysis gases of residual fuel oil have not time enough to react with oxygen. It is obvious that if combustion of coke particles is taken into account, the oxygen content in the blast decreases to such a level, that unburnt pyrolysis gases can flow out of the raceway causing problems. The distribution of coke void fraction has been succeeded to predict in the raceway domain. Coke particles fall from the upper part of the raceway to the hot blast forming locally high concentrations, which affect very strongly the oxygen distribution of the hot blast. (orig.) SULA 2 Research Programme; 10 refs.

  2. Modelling of turbulent combustion in the blast furnace raceway

    Energy Technology Data Exchange (ETDEWEB)

    Karvinen, R.; Maekiranta, R. [Tampere Univ. (Finland). Energy and Process Engineering

    1996-12-31

    The phenomena concerning coke-gas -suspension and simultaneous combustion of solid coke particles and residual fuel oil in a blast furnace raceway are modelled. The flow field of suspension is predicted by using the two fluid model, which is based on the Eulerian method, in the Phoenics code. The standard k-e -model of turbulence is used. Pyrolysis of oil droplets is calculated with the own coded subroutine, which is based on the Lagrangian approach. Gas phase reaction rate is assumed to be controlled by chemical kinetics. Radiative heat transfer is calculated by using the six-flux method. Heterogenous surface reactions are used for the coke particles. Calculations without coke combustion show that due to a poor mixing in the hot blast, pyrolysis gases of residual fuel oil have not time enough to react with oxygen. It is obvious that if combustion of coke particles is taken into account, the oxygen content in the blast decreases to such a level, that unburnt pyrolysis gases can flow out of the raceway causing problems. The distribution of coke void fraction has been succeeded to predict in the raceway domain. Coke particles fall from the upper part of the raceway to the hot blast forming locally high concentrations, which affect very strongly the oxygen distribution of the hot blast. (orig.) SULA 2 Research Programme; 10 refs.

  3. Modeling of microgravity combustion experiments

    Science.gov (United States)

    Buckmaster, John

    1995-01-01

    This program started in February 1991, and is designed to improve our understanding of basic combustion phenomena by the modeling of various configurations undergoing experimental study by others. Results through 1992 were reported in the second workshop. Work since that time has examined the following topics: Flame-balls; Intrinsic and acoustic instabilities in multiphase mixtures; Radiation effects in premixed combustion; Smouldering, both forward and reverse, as well as two dimensional smoulder.

  4. Quantifying emissions from spontaneous combustion

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-09-01

    Spontaneous combustion can be a significant problem in the coal industry, not only due to the obvious safety hazard and the potential loss of valuable assets, but also with respect to the release of gaseous pollutants, especially CO2, from uncontrolled coal fires. This report reviews methodologies for measuring emissions from spontaneous combustion and discusses methods for quantifying, estimating and accounting for the purpose of preparing emission inventories.

  5. “Bio” combustibles o el mito del oro verde ¿Política ambiental, “exportación de naturaleza”, o etnocidio?

    Directory of Open Access Journals (Sweden)

    Anne-Lise Naizot

    2013-09-01

    Full Text Available El término “biocombustible” se refiere en su aceptación general a los combustibles que pueden ser obtenidos a partir de biomasa, de leña, y de más de 14 variedades de cultivos (caña de azúcar, soya, palma aceitera, ricino, maíz, colza, girasol, sorgo, trigo, mandioca, etc.. Los dos “biocombustibles”, “bio”etanol y “bio”diesel, son obtenidos, respectivamente, por fermentación de productos ricos en azúcares, almidones o celulosas (bioetanol y de aceites vegetales como la palma africana, girasol, higuerilla, soya, etc. (biodiesel

  6. Desempeño del método cromatográfico para el estudio de estabilidad del aceite de hígado de tiburón microencapsulado empleando acetato de quitosana

    Directory of Open Access Journals (Sweden)

    Caridad García

    Full Text Available Objetivo: Evaluar el desempeño del método para la cuantificación de la vitamina A en el aceite microencapsulado, empleando acetato de quitosana y maltodextrina como agentes encapsulantes, así como estudiar la estabilidad del aceite microencapsulado. Materiales y métodos: Los parámetros evaluados se correspondieron con lo establecido internacionalmente para este estudio: especificidad, exactitud y precisión. El estudio de estabilidad se realizó durante 12 meses a temperatura ambiente (30 ± 2ºC y 70 ± 5 % de humedad relativa, evaluándose en el tiempo la eficiencia de encapsulación, aceite superficial, pérdidas por desecación, contenido de vitamina A y conteo microbiológico. Resultados: Se demostró que el método evaluado fue específico, preciso y exacto para la determinación del contenido de vitamina A en la mezcla de aceite microencapsulado. Los resultados demuestran que el aceite microencapsulado tiene un comportamiento estable en cuanto a los indicadores evaluados, evidenciándose la protección ofrecida por los componentes de la pared de las microcápsulas. Conclusiones: El método empleado en la cuantificación de la vitamina A en el aceite microencapsulado resultó específico, exacto y preciso, demostrándose su aplicabilidad para el control de calidad y estudio de estabilidad. El aceite microencapsulado con acetato de quitosana y maltodextrina como agentes encapsulantes, es estable física, química y microbiológicamente, durante 12 meses.

  7. Consistencia de lípidos estructurados a partir de aceite de pescado y grasa de palmiste

    Directory of Open Access Journals (Sweden)

    Gioielli, Luiz Antonio

    2003-06-01

    Full Text Available Through interesterification of oils and fats is possible to obtain structured lipids (SL, which are considered functional foods, due their potential effects on the prevention of diseases. For this reason, there is great interest in the production of SL. The objective of this paper was to obtain structured lipids from chemical interesterification from palm kernel fat and fish oil and to analyse the interactions that occur in the binary mixtures of these lipids. Six samples consisting of two individual samples and four binary mixtures were studied. The samples were analyzed for fatty acid composition and consistency at the range temperature from 5 to 25ºC. A mathematical model of multiple regression of the quadratic type was applied. The results showed that the interactions between the two components were significant. The consistency depended on the palm kernel fat and on the binary interactions between palm kernel fat and fish oil. The negative coefficients to the consistency showed an antagonic effect which is characteristic of eutectic interactions between fats.Por medio de la interesterificación de mezclas de aceites y grasas, es posible obtener lípidos estructurados (SL, los cuales son considerados como alimentos funcionales por presentar gran potencial en la prevención de diversas enfermedades. Por esta razón, existe un gran interés en la producción de SL. El objetivo de este trabajo fue obtener lípidos estructurados por interesterificación química a partir de grasa de palmiste y aceite de pescado y analizar las interacciones que ocurrieron en las mezclas binárias de los lípidos. Fueron estudiadas seis muestras, representadas por dos muestras individuales y cuatro mezclas binárias. Las muestras fueron analizadas en cuanto a su composición de ácidos grasos y consistencia en el rango de temperaturas de 5 a 25ºC. Se aplicó un modelo de regresión múltiple del tipo cuadrático. Los resultados demostraron que las

  8. Co-sintering of treated APC-residues with bottom ash

    DEFF Research Database (Denmark)

    Jensen, Dorthe Lærke; Bergfeldt, Britta; Vehlow, Jürgen

    2001-01-01

    the influence of co-sintering of Ferrox products with bottom ashes on the quality of the residues and the effects on the combustion process. Only few elements showed higher concentrations in the bottom ashes of these co-combustion tests compared to reference tests. No significant effect on the leaching......Air pollution control residues stabilised by means of the Ferrox process can be sager disposed of due to lower contents of soluble salts and lesssoluble heavy metals stabilised in iron oxides. Co-combustion tests in the Karlsruhe test incinerator TAMARA were carried out in order to investigate...... behaviour of the bottom ashes could be found. During the co-combustion process an increase in SO2 concentrations in the raw gas and slightly lower temperatures in the fuel bed could be observed....

  9. Influencia del proceso de maduración del fruto en la calidad sensorial de aceites de oliva virgen de las variedades Picual, Hojiblanca y Picudo

    Directory of Open Access Journals (Sweden)

    Jiménez Herrera, B.

    2012-10-01

    Full Text Available The sensory quality of virgin olive oil is closely correlated with the cultivar and the degree of ripening of the olive fruit. The aim of the present work was to investigate the influence of ripening degree on sensory profile of monovarietal virgin olive oils (VOO in order to establish an optimum harvesting time. Fruit obtained from three different cultivars, Picual, Picudo and Hojiblanca were picked at nine different stages of ripeness. The quality parameters were evaluated and the sensory characteristics were determinate by a sensor panel. The analytical parameters decrease slightly in all cultivars. The evolution of the organoleptic characteristics of the virgin olive oil is reported and typical flavors are described for each cultivar. In all studied cultivar, “fruity” and “bitter” attributes decreased during the ripening and conversely “sweet” attribute increased. The results showed in this work could be considered useful for providing information about the evolution of sensory quality of virgin olive oils during ripening to obtain those based on market preferences.

    La calidad sensorial del aceite de oliva virgen (AOV está estrechamente relacionada con la variedad y el grado de maduración de la aceituna. El objetivo del presente trabajo fue investigar la influencia del grado de maduración sobre el perfil sensorial de aceites de oliva virgen monovarietales con el fin de establecer el momento óptimo de recolección. Los frutos de tres variedades diferentes, Picual, Picudo y Hojiblanca fueron recolectados en nueve etapas de maduración diferentes. Los parámetros de calidad fueron evaluados y las características organolépticas se determinaron por un panel de cata. Los resultados muestran que los parámetros analíticos disminuyeron ligeramente en todas las variedades. Para cada variedad se describe la evolución de las características organolépticas de los aceites de oliva virgen así como sus flavores típicos. En

  10. Migración de hierro y níquel, y estabilidad oxidativa del aceite refinado de soja calentado en utensilios culinarios de diversos materiales

    Directory of Open Access Journals (Sweden)

    Almeyda Haj-Isa, Niurka Maritza

    2007-12-01

    Full Text Available Cookware may release some inorganic components into foods during cooking, some of which have undesirable consequences. In fried foods, for instance, oil oxidation is favored by metals. The present study evaluated oxidative stability (AOCS method and iron and nickel migration (inductively coupled plasma-optical emission spectrometry into refined soybean oil in four cycles, with intervals of 24 hours. The cookware materials were glass, aluminum, stainless steel, iron and soapstone. The results demonstrated that the lowest metal migration occurred from glass and aluminum pans while the oil heated in these pans showed the highest oxidative stability. The highest migration of Fe and Ni into the oil occurred from the soapstone and iron pots (3.94 and 3.21 mg _ kg-1, respectively.Nevertheless, increasing loss of oxidative stability was evident in the oils heated in the soapstone, stainless steel and iron cookware, in this order. Since iron migration was lower from glass and aluminum pans, these were considered the best type of materials for fryingDurante la elaboración de alimentos los utensilios culinarios pueden liberar componentes inorgánicos ocasionalmente no deseables. La oxidación del aceite es durante la fritura es favorecida por la presencia de metales. Fue evaluada la migración de hierro y níquel (espectrometría de emisión óptica y la estabilidad oxidativa (método AOCS del aceite de soja sometido a cuatro calentamientos con intervalos de 24 horas en cazuelas de vidrio, aluminio, acero inoxidable, hierro y piedra-jabón. La mayor migración de hierro al aceite ocurrió en las cazuelas de hierro (3,94 mg•kg–1 y piedra (3,21 mg _ kg–1, sin diferencia estadística entre ellas. La pérdida progresiva de estabilidad oxidativa fue acentuada en los aceites calentados en utensilios de piedra, acero inoxidable e hierro, en tal orden. Vidrio y aluminio fueron considerados los mejores materiales para la fabricación de cazuelas

  11. Inhibición de Paenibacillus larvae empleando una mezcla de aceites esenciales y timol Inhibition of Paenibacillus larvae employing a mixture of essential oils and thymol

    Directory of Open Access Journals (Sweden)

    S. R. Fuselli

    2006-04-01

    Full Text Available Se evaluó la actividad antimicrobiana in vitro de una mezcla de dos aceites esenciales y timol frente a Paenibacillus larvae, agente causal de la enfermedad Loque americana, que afecta a las abejas. Los aceites esenciales utilizados fueron canela (Cinnamomum zeylanicum y tomillo (Thymus vulgaris, con el agregado de timol, componente mayoritario del tomillo presente en un 39,9%. Los parámetros medidos fueron la concentración inhibitoria mínima (CIM en caldo Muller-Hinton, mediante dilución seriada, y la concentración bactericida mínima (CBM en agar MYPGP. El aceite esencial de tomillo registró valores de CIM entre 150 y 250 μg/ml, y de CBM entre 200 y 300 μg/ml, mientras que para el aceite esencial de canela los valores de CIM y de CBM obtenidos fueron 50 a 100 μg/ml y 100 a 125 μg/ml, respectivamente. El timol presentó valores de CIM y de CBM similares, de 100 a 150 μg/ml. No se detectaron diferencias significativas entre las cepas bacterianas estudiadas, pero sí entre la actividad de los aceites esenciales y la del timol (PIn vitro antimicrobial activity of a mixture of two essential oils and thymol against Paenibacillus larvae, causal agent of American Foulbrood (AFB, was evaluated. The essential oils were extracted from cinnamon (Cinnamomum zeylanicum and thyme (Thymus vulgaris. The third component used, thymol, is the major component of the essential oil of thyme which contains 39.9 % of thymol. Minimal inhibitory concentration (MIC in Mueller-Hinton broth by the tube dilution method and minimal bactericide concentration (MBC on MYPGP agar were evaluated. Thyme registered MIC values of 150-250 μg/ml and MBC values of 200-300 μg/ml, while the MIC and MBC values obtained for cinnamon were of 50-100 μg/ml and 100-125 μg/ml. Thymol showed similar MIC and MBC values of 100-150 μg/ml. No significant differences between the bacterial strains were detected, but significant differences between essential oils and thymol activity

  12. Determinación de compuestos polares por TLC-FID en aceites refinado y semi-hidrogenado de soja sometidos a calentamiento prolongado

    Directory of Open Access Journals (Sweden)

    Cruzian, J. L.

    1997-06-01

    Full Text Available The thermal degradation of oils and fats leads to the formation of polar compounds, which is the reason why their determination is adopted for the quality control of the oil and fat used in frying. Samples of refined and partially hydrogenated soybean oil were heated for 30 and 60 hours respectively and the polar compounds content were determined using the lUPAC-AOAC official method and TLC-FID. The samples of oil and the fractions separated on the column were applied to the chromarods and developed in petroleum ether: diethyl ether (93:7 v/v. The determination of polar compounds by lUPAC method and by TLC-FID presented similar results (P-value<< 0,001, although when the content was greater than 16% the second method gave higher values. The results showed that the state of degradation of oils and fats as measured for the quantity of polar compounds can be determined alternatively by TLC-FID, presenting a significant reduction in time, hand work and solvent volume.

    La degradación térmica de aceites y grasas lleva a la formación de compuestos polares, motivo por el cual su determinación es usada como control de calidad de aceites y grasas utilizadas en fritura. Muestras de aceite de soja refinado y semi-hidrogenado fueron calentadas durante 30 y 60 horas respectivamente y el contenido de compuestos polares fue determinado utilizando el método oficial lUPAC-AOAC y TLCFID. Las muestras de aceite y las fracciones separadas en la columna fueron aplicadas en los «chromarods» y desarrolladas en éter de petróleo: éter etílico (93:7 v/v. La determinación de compuestos polares por el método lUPAC y por TLC-FID, dieron resultados similares (P-value<< 0,001, aunque los obtenidos por el segundo método fueron superiores, cuando los compuestos polares superan el 16%. Los resultados obtenidos indican que el estado de descomposición de aceites y grasas medido por la cantidad de compuestos polares puede ser determinado alternativamente por

  13. Repairing an installation and processing the residues

    International Nuclear Information System (INIS)

    Malet, J.C.; Duverger de Cuy, G.; Sophy, Y.; Cucinotta, A.

    1989-01-01

    After a sodium leak in a locale, producing a fire, the operator's first concern is to repair the plant. Since the residual sodium and the products of combustion are chemically aggressive, the personnel will have to perform this operation in a hostile environment. This paper presents answers which can be given to the three questions which will however rise: When can the intervention begin? How will it be performed? What should be done with the residues of combustion? This document aims at presenting the different solutions to this problem, these solutions being derived from experiments carried out in France either in the Esmeralda Programme, which is managed jointly by CEA and ENEA, or in the other French programmes. As a general rule, the intervention inside the locale can be made much more easier if: it was foreseen right from the beginning of the design (access under the pipes, anchorage for handling, etc.); the incident can have been localised thanks to the monitoring of locales, enabling the video recording of the first instants, that is, as long as visibility does not fall to zero due to the aerosols from the fire. (author)

  14. Techniques de combustion Combustin Techniques

    Directory of Open Access Journals (Sweden)

    Perthuis E.

    2006-11-01

    Full Text Available L'efficacité d'un processus de chauffage par flamme est étroitement liée à la maîtrise des techniques de combustion. Le brûleur, organe essentiel de l'équipement de chauffe, doit d'une part assurer une combustion complète pour utiliser au mieux l'énergie potentielle du combustible et, d'autre part, provoquer dans le foyer les conditions aérodynamiques les plus propices oux transferts de chaleur. En s'appuyant sur les études expérimentales effectuées à la Fondation de Recherches Internationales sur les Flammes (FRIF, au Groupe d'Étude des Flammes de Gaz Naturel (GEFGN et à l'Institut Français du Pétrole (IFP et sur des réalisations industrielles, on présente les propriétés essentielles des flammes de diffusion aux combustibles liquides et gazeux obtenues avec ou sans mise en rotation des fluides, et leurs répercussions sur les transferts thermiques. La recherche des températures de combustion élevées conduit à envisager la marche à excès d'air réduit, le réchauffage de l'air ou son enrichissement à l'oxygène. Par quelques exemples, on évoque l'influence de ces paramètres d'exploitation sur l'économie possible en combustible. The efficiency of a flame heating process is closely linked ta the mastery of, combustion techniques. The burner, an essential element in any heating equipment, must provide complete combustion sa as to make optimum use of the potential energy in the fuel while, at the same time, creating the most suitable conditions for heat transfers in the combustion chamber. On the basis of experimental research performed by FRIF, GEFGN and IFP and of industrial achievements, this article describesthe essential properties of diffusion flames fed by liquid and gaseous fuels and produced with or without fluid swirling, and the effects of such flames on heat transfers. The search for high combustion temperatures means that consideration must be given to operating with reduced excess air, heating the air or

  15. Efecto del enlatado en aceite y salmuera y su posterior almacenamiento sobre los lípidos de la bacoreta (Euthynnus alletteratus

    Directory of Open Access Journals (Sweden)

    Aubourg, Santiago P.

    1995-04-01

    Full Text Available Changes produced in the lipid fraction of Little Tunny during canning in oil and in brine and during its subsequent storage were studied in order to compare the effect of both dipping procedures. The effect of the type of covering medium on both the total lipid composition and on the phospholipid fraction was determined.
    Canning in oil was shown to lead to certain changes in the composition of the final product, there being a decrease in the phospholipid and fatty acid (16:0,18:0, 20:4ω6, 20:5ω3, 24:1ω9 and 22:6ω content of the total lipids. Furthermore, the presence of triglycerides in the oil used for canning leads to increases in some fatty acids (oleic and linoleic in the samples. The lipid content of samples canned in brine were lower than initial values. This difference due to processing was not detected in samples canned in oil.
    The phospholipid study showed the presence of 1-O-alk-1-enyl-ether chains, the qualitative and quantitative composition of which was studied. The thermal treatment Involved in both dipping procedures provoked a sharp decrease in the plasmalogen content, while the polyunsaturated fatty acid composition was significantly lower ¡n the oil canned samples than in the raw samples. This decrease due to processing can be explained as an effect of the heat and of the extraction capacity of the oil.

    Se estudiaron los cambios producidos en la fracción lipídica de la bacoreta como resultado de su enlatado en dos modalidades distintas (aceite vegetal y salmuera y su posterior almacenamiento. El efecto del medio de cobertura se estudió sobre la composición lipídica total y sobre la fracción fosfolipídica.
    La comparación de los dos tipos de enlatado demostró que la presencia del aceite de cobertura puede provocar modificaciones en la composición del producto final como el descenso del contenido de fosfolípidos y de numerosos ácidos grasos (16:0,18:0,20:4ω6, 20:5ω3, 24:ω9 y 22:6ω3

  16. Tratamiento enzimático en la extracción de aceite y obtención de antioxidantes a partir de semilla de onagra, Oenothera biennis, por prensado en frío

    Directory of Open Access Journals (Sweden)

    Zúñiga, María E.

    2007-03-01

    Full Text Available The aim of this work was to improve the yield in evening primrose oil extraction and the antioxidant potential of the residual meal using an enzyme assisted extraction process with cold pressing. Among four commercial enzymes, a mixture of two of them was selected in order to evaluate the effect of enzyme-substrate ratio, temperature, moisture and period of time of the enzymatic pretreatment on the extracted oil. The oil yield increased by 12% when the seeds were pretreated with 2% enzyme-substrate ratio of a mixture of 100G Ultrazym and Cellubrix (1:1 for 15 h at 40oC and 40% moisture. The defatted meal obtained from the enzyme aided process enhanced its phenol content and improved its potential antioxidant activity in comparison to the control from 250 to 276 mg of phenols/g of meal and from 1463 to 1558 mg of trolox/g of meal respectively.Se espera que el tratamiento enzimático, previo al prensado en frío, de la semilla de Oenothera biennis, mejore el rendimiento de extracción de aceite y la cantidad de antioxidantes extraídos de la harina residual. De una serie de cuatro preparados enzimáticos comerciales, se selecciona el más adecuado, el cual es evaluado bajo distintas condiciones de incubación: razones enzima/sustrato, tiempo, humedad y temperatura. El rendimiento aumenta un 12 % cuando se realiza un doble prensado sobre la semilla tratada con una mezcla enzimática formulada con Ultrazym 100G y Cellubrix en razón 1:1, concentración enzima/sustrato del 2 % p/p (base húmeda, durante 15 horas de incubación a 45 °C y 40 % de humedad. La harina residual desgrasada aumenta su contenido de antioxidantes desde 250 a 276 mg de fenoles expresados en catequina y el extracto mejora su actividad antioxidante desde 1463 a 1558 mg de trolox por gr de harina.

  17. Residual gas analysis

    International Nuclear Information System (INIS)

    Berecz, I.

    1982-01-01

    Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

  18. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Paul Ziemkiewicz; Tamara Vandivort; Debra Pflughoeft-Hassett; Y. Paul Chugh; James Hower

    2008-08-31

    The Combustion Byproducts Recycling Consortium (CBRC) program was developed as a focused program to remove and/or minimize the barriers for effective management of over 123 million tons of coal combustion byproducts (CCBs) annually generated in the USA. At the time of launching the CBRC in 1998, about 25% of CCBs were beneficially utilized while the remaining was disposed in on-site or off-site landfills. During the ten (10) year tenure of CBRC (1998-2008), after a critical review, 52 projects were funded nationwide. By region, the East, Midwest, and West had 21, 18, and 13 projects funded, respectively. Almost all projects were cooperative projects involving industry, government, and academia. The CBRC projects, to a large extent, successfully addressed the problems of large-scale utilization of CCBs. A few projects, such as the two Eastern Region projects that addressed the use of fly ash in foundry applications, might be thought of as a somewhat smaller application in comparison to construction and agricultural uses, but as a novel niche use, they set the stage to draw interest that fly ash substitution for Portland cement might not attract. With consideration of the large increase in flue gas desulfurization (FGD) gypsum in response to EPA regulations, agricultural uses of FGD gypsum hold promise for large-scale uses of a product currently directed to the (currently stagnant) home construction market. Outstanding achievements of the program are: (1) The CBRC successfully enhanced professional expertise in the area of CCBs throughout the nation. The enhanced capacity continues to provide technology and information transfer expertise to industry and regulatory agencies. (2) Several technologies were developed that can be used immediately. These include: (a) Use of CCBs for road base and sub-base applications; (b) full-depth, in situ stabilization of gravel roads or highway/pavement construction recycled materials; and (c) fired bricks containing up to 30%-40% F

  19. Characterisation of ashes produced by co-combustion of recovered fuels and peat

    Energy Technology Data Exchange (ETDEWEB)

    Frankenhaeuser, M. [Borealis Polymers Oy, Porvoo (Finland)

    1997-10-01

    The current project focuses on eventual changes in ash characteristics during co-combustion of refuse derived fuel with coal, peat, wood or bark, which could lead to slagging, fouling and corrosion in the boiler. Ashes were produced at fluidised bed (FB) combustion conditions in the 15 kW reactor at VTT Energy, Jyvaeskylae, the fly ash captured by the cyclone was further analysed by XRF at Outokumpu Geotechnical Laboratory, Outokumpu. The sintering behaviour of these ashes was investigated using a test procedure developed at the Combustion Chemistry Research Group at Aabo Akademi University. The current extended programme includes a Danish refuse-derived fuel (RDF), co-combusted with bark/coal (5 tests) and wood/coal (2 tests), a RF from Jyvaskyla (2 tests with peat/coal) and de-inking sludges co- combusted at full-scale with wood waste or paper mill sludge (4 ashes provided by IVO Power). Ash pellets were thermally treated in nitrogen in order to avoid residual carbon combustion. The results obtained show no sintering tendencies below 600 deg C, significant changes in sintering are seen with pellets treated at 1000 deg C. Ash from 100 % RDF combustion does not sinter, 25 % RDF co-combustion with wood and peat, respectively, gives an insignificant effect. The most severe sintering occurs during co-combustion of RDF with bark. Contrary to the earlier hypothesis a 25 % coal addition seems to have a negative effect on all fuel blends. Analysis of the sintering results versus ash chemical composition shows, that (again), in general, an increased level of alkali chlorides and sulphates gives increased sintering. Finally, some results on sintering tendency measurements on ashes from full-scale CFB co-combustion of deinking sludge with wood waste and paper mill sludge are given. This shows that these ashes show very little, if any, sintering tendency, which can be explained from ash chemistry

  20. HERCULES Advanced Combustion Concepts Test Facility: Spray/Combustion Chamber

    Energy Technology Data Exchange (ETDEWEB)

    Herrmann, K. [Eidgenoessische Technische Hochschule (ETH), Labor fuer Aerothermochemie und Verbrennungssysteme, Zuerich (Switzerland)

    2004-07-01

    This yearly report for 2004 on behalf of the Swiss Federal Office of Energy (SFOE) at the Laboratory for Aero-thermochemistry and Combustion Systems at the Federal Institute of Technology ETH in Zurich, Switzerland, presents a review of work being done within the framework of HERCULES (High Efficiency R and D on Combustion with Ultra Low Emissions for Ships) - the international R and D project concerning new technologies for ships' diesels. The work involves the use and augmentation of simulation models. These are to be validated using experimental data. The report deals with the development of an experimental set-up that will simulate combustion in large two-stroke diesel engines and allow the generation of reference data. The main element of the test apparatus is a spray / combustion chamber with extensive possibilities for optical observation under variable flow conditions. The results of first simulations confirm concepts and shall help in further work on the project. The potential offered by high-speed camera systems was tested using the institute's existing HTDZ combustion chamber. Further work to be done is reviewed.

  1. Jet plume injection and combustion system for internal combustion engines

    Science.gov (United States)

    Oppenheim, Antoni K.; Maxson, James A.; Hensinger, David M.

    1993-01-01

    An improved combustion system for an internal combustion engine is disclosed wherein a rich air/fuel mixture is furnished at high pressure to one or more jet plume generator cavities adjacent to a cylinder and then injected through one or more orifices from the cavities into the head space of the cylinder to form one or more turbulent jet plumes in the head space of the cylinder prior to ignition of the rich air/fuel mixture in the cavity of the jet plume generator. The portion of the rich air/fuel mixture remaining in the cavity of the generator is then ignited to provide a secondary jet, comprising incomplete combustion products which are injected into the cylinder to initiate combustion in the already formed turbulent jet plume. Formation of the turbulent jet plume in the head space of the cylinder prior to ignition has been found to yield a higher maximum combustion pressure in the cylinder, as well as shortening the time period to attain such a maximum pressure.

  2. Acid digestion and pressurization control in combustible radwaste treatment

    International Nuclear Information System (INIS)

    Allen, C.R.; Cowan, R.G.; Grelecki, C.J.

    1978-01-01

    Acid digestion has been developed to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to process radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September, 1977, and is currently undergoing nonradioactive shakedown tests. Radioactive operation is expected in May, 1978. Because of uncertainties in waste composition and reactivity, the system was required to contain pressurizations. This led to the development of a simple and inexpensive system, which is capable of attenuating a shock wave from a full scale vapor detonation. The system has potential application in a wide spectrum of chemical reactors, since the fabrication materials are resistant to a very wide range of corrosive chemical attack

  3. Acid digestion of combustible wastes: a status report

    International Nuclear Information System (INIS)

    Lerch, R.E.

    1975-05-01

    Work at the Hanford Engineering Development Laboratory on development of the acid digestion process for treating combustible wastes is discussed. Materials such as paper, rubber, and plastics are readily decomposed into a low volume, noncombustible residue. Engineering results using the Acid Digestion Test Unit are discussed. Tests to date generally duplicated earlier laboratory results with respect to waste processing rates, volume reduction, off-gas generation rates and volumes, acid consumption, and completeness of reaction. Demonstrated processing rates were as high as 5 kg/hr for short duration run periods. The tests indicated engineering feasibility of the acid digestion process and showed acid digestion to be a potentially attractive method for treating combustible nuclear wastes. Other areas discussed in the report are behavior of plutonium and americium during acid digestion, behavior of various construction materials, and safety. An integrated flowsheet for operation of an acid digestion unit is also presented. (U.S.)

  4. Biogas utilization as flammable for internal combustion engine

    International Nuclear Information System (INIS)

    Cardenas, H.

    1995-01-01

    In this work the energetic potential stored in form of generated biogas of organic industrial wastes treatment is analyzed. Biogas utilization as flammable at internal combustion engine coupled to electrical energy generating is studied in the Wastewater Treatment Plant of Bucaramanga city (Colombia). This Plant was designed for 160.000 habitants treatment capacity, 1300 m3/h wealth, 170 BDO/m3 residues concentration and 87% process efficiency. The plant generate 2.000 m3/d of biogas. In laboratory trials was worked with biogas originating from Treatment Plant, both without purifying and purified, and the obtained results were compared with both yields determined with 86-octanes gasoline and natural gas. The analysis of pollutant by-products generated in combustion process as leak gases, present corrosive compounds and not desirable. elements in biogas composition are included

  5. Thermogravimetric analysis of co-combustion between microalgae and textile dyeing sludge.

    Science.gov (United States)

    Peng, Xiaowei; Ma, Xiaoqian; Xu, Zhibin

    2015-03-01

    The synergistic interaction and kinetics of microalgae, textile dyeing sludge and their blends were investigated under combustion condition by thermogravimetric analysis. The textile dyeing sludge was blended with microalgae in the range of 10-90wt.% to investigate their co-combustion behavior. Results showed that the synergistic interaction between microalgae and textile dyeing sludge improved the char catalytic effect and alkali metals melt-induced effect on the decomposition of textile dyeing sludge residue at high temperature of 530-800°C. As the heating rate increasing, the entire combustion process was delayed but the combustion intensity was enhanced. The lowest average activation energy was obtained when the percentage of microalgae was 60%, which was 227.1kJ/mol by OFW and 227.4kJ/mol by KAS, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Application of LES for Analysis of Unsteady Effects on Combustion Processes and Misfires in DISI Engine

    Directory of Open Access Journals (Sweden)

    Goryntsev D.

    2013-10-01

    Full Text Available Cycle-to-cycle variations of combustion processes strongly affect the emissions, specific fuel consumption and work output. Internal combustion engines such as Direct Injection Spark-Ignition (DISI are very sensitive to the cyclic fluctuations of the flow, mixing and combustion processes. Multi-cycle Large Eddy Simulation (LES analysis has been used in order to characterize unsteady effects of combustion processes and misfires in realistic DISI engine. A qualitative analysis of the intensity of cyclic variations of in-cylinder pressure, temperature and fuel mass fraction is presented. The effect of ignition probability and analysis of misfires are pointed out. Finally, the fuel history effects along with the effect of residual gas on in-cylinder pressure and temperature as well as misfires are discussed.

  7. ESTUDIO DE SULFUROS DE MOLIBDENO GENERADOS MEDIANTE LA DESCOMPOSICIÓN TÉRMICA DE EMULSIONES AGUA/ACEITE

    Directory of Open Access Journals (Sweden)

    Ismael González

    2011-01-01

    Full Text Available Fueron preparados sólidos sulfurados tipo MoS2 mediante la descomposición térmica de emulsiones agua/aceite (W/O, incorporando en su fase acuosa heptamolibdato de amonio ((NH46Mo7O24.4H2O y un agente sulfurante, con el fin de evaluar fases activas que pudieran generarse en novedosos ca talizadores ultradispersos para conversión de hidrocarburos. Los sólidos fueron caracterizados por espectroscopia fotoelectrónica de rayos-x (XPS, oxidación a temperatura programada (TPO y análisis químico elemental. Los resultados de XPS revelaron que los sólidos presentan una superficie enriquecida en azufre, así como una significativa estabilidad a la oxidación por exposición al aire. Se comprobó que la cantidad de agente sulfurante presente originalmente en la emulsión es crucial para controlar la estequiometría de los sulfuros sintetizados. Los perfiles de oxidación permitieron diferenciar varios tipos de S y C, y muestran que ambos elementos tienden a oxidarse simultáneamente, sugiriendo que ambos elementos están íntimamente asociados en la estructura de estos materiales.

  8. Componente del insaponificable del aceite de oliva con polaridad comprendida entre el escualeno y los alcoholes triterpénicos

    Directory of Open Access Journals (Sweden)

    Lanzón, A.

    1992-10-01

    Full Text Available In the unsaponifiable matter of refined olive oils and, frequently, virgin olive oils of bad quality, a new compound with polarity between those of squalene and triterpenic alcohols was isolated. Mass spectrometry of this compound and of their hydrogenated and; sililated derivatives, demonstrated that the compound was a long chain alcohol having 426 of molecular weight, polyisoprenic structure similar to that of squalene, and the hydroxyl group attached at the C-2 carbon atom.

    Se ha estudiado y determinado la estructura de un compuesto, de polaridad comprendida entre el escualeno y los alcoholes triterpénicos, que se encuentra en el insaponificable de los aceites de oliva refinados y en muchas ocasiones en el de los vírgenes, sobre todo en los de baja calidad. La espectrometría de masas del mismo y, de sus derivados hidrogenado y sililado, ha puesto de manifiesto que se trata de un alcohol triterpénico lineal, de peso molecular 426, con el esqueleto similar al del escualeno y con el grupo hidroxilo en posición 2.

  9. Caracterización del color de los aceites de oliva vírgenes de cultivares catalanes

    Directory of Open Access Journals (Sweden)

    Tous Martí, J.

    1992-12-01

    Full Text Available Colour variation of virgin oil from 34 olive cultivars growing in Catalonia (Spain was analyzed by the ABT (Bromthymol Blue modified method. In addition, the preferences of consumers in the Denomination of Origin Siurana (Tarragona were studied, in relation to coloration. The results obtained show that varietal differences exist in the colour index studied and that the commercial preferences vary according to the oil markets.

    Se analizan mediante el método ABT (Azul de Bromotimol modificado, las variaciones del color de los aceites vírgenes provenientes de 34 variedades de olivo cultivadas en Cataluña y, al mismo tiempo, se estudian las preferencias de los consumidores de la Denominación de Origen Siurana (Tarragona, en cuanto a tonalidades de color. Los resultados obtenidos indican que existen diferencias varietales en los índices de color estudiados y que las preferencias comerciales varían según los mercados oleícolas.

  10. Walnut and almond oil screw-press extraction at industrial scale: Effects of process parameters on oil yield and quality; Extracción de aceite de nuez y almendra a escala industrial: efecto de parámetros del proceso sobre el rendimiento y la calidad del aceite

    Energy Technology Data Exchange (ETDEWEB)

    Martínez, M. L.; Bordón, M.G.; Bodoira, R. M.; Penci, M.C.; Ribotta, P.D.; Maestri, D.M.

    2017-07-01

    Walnut and almond kernels are highly nutritious mainly due to their high oil contents. In this study, 32 factorial experimental designs were used to optimize processes for oil extraction by screw-pressing at industrial scale. Experimental designs included seed moisture content (SMC), and restriction die (RD) as the main processing parameters. Theoretical models were scanned against experimental data in order to optimize oil extraction conditions. The response variables analyzed were oil yield (OY), fine solid content (FC) in oil, and oil quality parameters. Fitted models for OY indicated maximum predicted values similar to the highest experimental values. Walnut oil extractions showed a maximum OY (84.5 ± 2.3 %) at 7.21% SMC, and 10 mm RD. For almond kernels, maximum OY (71.9 ± 3.5%) was obtained at 9.42% SMC, and 12 mm RD. Chemical quality parameters from both oils were in the ranges stated in Codex (FAO/WHO) standards for virgin (non-refined) oils. [Spanish] La nuez y almendra son frutos sumamente nutritivos debido a su alto contenido de aceite. Mediante un diseño experimental de tipo factorial 32 se optimizó el proceso de extracción de estos aceites con prensa de tornillo a escala industrial. Las variables de proceso analizadas fueron el contenido de humedad de la semilla (CHS) y el diámetro de reducción (DR). Los modelos ajustados para rendimiento de aceite (RA) indicaron valores máximos predichos similares a los valores experimentales. Las extracciones de aceite de nuez mostraron un RA máximo (84,5 ± 2,3%) a 7,21% CHS, y 10 mm DR. Para almendra, se obtuvo un máximo de RA (71,9 ± 3,5%) con 9,42% de CHS y 12 mm de DR. Los parámetros de calidad química de ambos aceites se encontraban en los rangos establecidos en las normas del Codex (FAO / OMS) para aceites vírgenes (no refinados).

  11. Twenty-fifth symposium (international) on combustion

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    Approximately two-thirds of the papers presented at this conference are contained in this volume. The other one-third appear in special issues of ''Combustion and Flame'', Vol. 99, 1994 and Vol. 100, 1995. Papers are divided into the following sections: Supersonic combustion; Detonations and explosions; Internal combustion engines; Practical aspects of combustion; Incineration and wastes; Sprays and droplet combustion; Coal and organic solids combustion; Soot and polycyclic aromatic hydrocarbons; Reaction kinetics; NO x ; Turbulent flames; Turbulent combustion; Laminar flames; Flame spread, fire and halogenated fire suppressants; Global environmental effects; Ignition; Two-phase combustion; Solid propellant combustion; Materials synthesis; Microgravity; and Experimental diagnostics. Papers have been processed separately for inclusion on the data base

  12. Método de análisis de calidad del aceite durante el freído por inmersión para pequeñas y medianas empresas

    Directory of Open Access Journals (Sweden)

    Efraín Hisnardo Rojas Uribe

    2011-01-01

    Full Text Available Este trabajo estudió el deterioro de un aceite comercial, Frytollíquido, bajo condiciones controladas de freído, empleando como método estandarizado para su evaluación el índice de anisidina (IAn. Se determinó el efecto de la temperatura y del tiempo de fritura, 170 °C hasta 10 horas y 200 °C hasta 6 horas, en presencia de los aceleradores: agua, 1% y 8% en peso con respecto al aceite, y material no lipídico, 1% y 6% en peso con respecto al aceite, manteniendo constante el flujo de aire en 25 L h-1. Posteriormente se estableció la relación del IAn con las propiedades color y viscosidad, para determinar su viabilidad téc-nica como métodos de valoración del deterioro de los aceites de fritura en pequeñas y medianas empresas (pyme. El aceite se deterioró más y en menor tiempo en los valores máximos del intervalo de estudio para cada uno de los factores experimentales, aunque sólo la temperatura tuvo un efecto estadísticamente diferente de cero (p

  13. EVALUACIÓN IN VITRO DE LA CAPACIDAD ANTIMICROBIANA DEL ACEITE ESENCIAL DE ENELDO–Anethum graveolens–COMO INHIBIDOR DEL CRECIMIENTO DE Staphylococcus aureus, COLIFORMES Y HONGOS PRESENTES EN LA CARNE DE TRUCHA

    Directory of Open Access Journals (Sweden)

    D. V. Castro

    2017-01-01

    Full Text Available El aceite esencial de eneldo tiene propiedades antimicrobianas y antifúngicas, por lo que puede ser utilizado para evitar el deterioro de los alimentos. En esta investigación se evaluó la capacidad inhibitoria del aceite esencial de eneldo sobre Staphylococcus aureus , coliformes y hongos presentes en la carne de trucha ( Oncorhynchus mykiss , utilizando 50 y 100 μL de aceite esencial. Se evaluaron diferentes condiciones de extracción del aceite esencial mediante el método de hidrodestilación y se logró un rendimiento máximo en base seca de 1,32% utilizando una relación 1:5 de agua y material vegetal durante 90 minutos. Al evaluar la capacidad antimicrobiana, el mayor efecto inhibitorio se obtuvo al aplicar 100 μL de aceite esencial de eneldo en cultivos de Staphylococcus aureus , coliformes fecales, coliformes totales y hongos, evidenciándose un mayor halo de inhibición para coliformes totales.

  14. Recycling of rubber tires in electric arc furnace steelmaking: simultaneous combustion of metallurgical coke and rubber tyres blends

    Energy Technology Data Exchange (ETDEWEB)

    Magdalena Zaharia; Veena Sahajwalla; Byong-Chul Kim; Rita Khanna; N. Saha-Chaudhury; Paul O' Kane; Jonathan Dicker; Catherine Skidmore; David Knights [University of New South Wales, Sydney, NSW (Australia). School of Materials Science and Engineering

    2009-05-15

    The present study investigates the effect of addition of waste rubber tires on the combustion behavior of its blends with coke for carbon injection in electric arc furnace steelmaking. Waste rubber tires were mixed in different proportions with metallurgical coke (MC) (10:90, 20:80, 30:70) for combustion and pyrolysis at 1473 K in a drop tube furnace (DTF) and thermogravimetric analyzer (TGA), respectively. Under experimental conditions most of the rubber blends indicated higher combustion efficiencies compared to those of the constituent coke. In the early stage of combustion the weight loss rate of the blends is much faster compared to that of the raw coke due to the higher volatile yield of rubber. The presence of rubber in the blends may have had an impact upon the structure during the release and combustion of their high volatile matter (VM) and hence increased char burnout. Measurements of micropore surface area and bulk density of the chars collected after combustion support the higher combustion efficiency of the blends in comparison to coke alone. The surface morphology of the 30% rubber blend revealed pores in the residual char that might be attributed to volatile evolution during high temperature reaction in oxygen atmosphere. Physical properties and VM appear to have a major effect upon the measured combustion efficiency of rubber blends. The study demonstrates that waste rubber tires can be successfully co-injected with metallurgical coke in electric arc furnace steelmaking process to provide additional energy from combustion. 44 refs., 11 figs., 2 tabs.

  15. The Low Load Limit of Gasoline Partially Premixed Combustion (PPC) - Experiments in a Light Duty Diesel Engine

    OpenAIRE

    Borgqvist, Patrick

    2013-01-01

    The decreasing oil supply, more stringent pollutant legislations and strong focus on decreasing carbon dioxide emissions drives the research of more efficient and clean combustion engines. One such combustion engine concept is Homogeneous Charge Compression Ignition (HCCI) which potentially achieves high efficiency and low NOx and soot emissions. One practical realization of HCCI in SI engines is to use a variable valve train to trap hot residual gases in order to increase the temperature of ...

  16. Suplementaci??n de la dieta de ovejas lecheras con aceite de girasol y l??pidos marinos para modificar la composici??n de la grasa de la leche: efecto sobre el rendimiento productivo de los animales, la microbiota y las caracter??sticas de la fermentaci??n ruminal y el perfil de ??cidos grasos de la leche y la digesta

    OpenAIRE

    Guti??rrez Toral, Pablo

    2011-01-01

    214 p. Se han realizado cinco experimentos con ovejas, con el objetivo de investigar el efecto de la suplementaci??n con aceite de girasol y, o bien aceite de pescado, o bien microalgas marinas, sobre la composici??n de los ??cidos grasos de la leche y la digesta, la micriobiota, la fermantaci??n ruminal y el rendimiento productivo de los animales

  17. ZMOTTO- MODELING THE INTERNAL COMBUSTION ENGINE

    Science.gov (United States)

    Zeleznik, F. J.

    1994-01-01

    The ZMOTTO program was developed to model mathematically a spark-ignited internal combustion engine. ZMOTTO is a large, general purpose program whose calculations can be established at five levels of sophistication. These five models range from an ideal cycle requiring only thermodynamic properties, to a very complex representation demanding full combustion kinetics, transport properties, and poppet valve flow characteristics. ZMOTTO is a flexible and computationally economical program based on a system of ordinary differential equations for cylinder-averaged properties. The calculations assume that heat transfer is expressed in terms of a heat transfer coefficient and that the cylinder average of kinetic plus potential energies remains constant. During combustion, the pressures of burned and unburned gases are assumed equal and their heat transfer areas are assumed proportional to their respective mass fractions. Even the simplest ZMOTTO model provides for residual gas effects, spark advance, exhaust gas recirculation, supercharging, and throttling. In the more complex models, 1) finite rate chemistry replaces equilibrium chemistry in descriptions of both the flame and the burned gases, 2) poppet valve formulas represent fluid flow instead of a zero pressure drop flow, and 3) flame propagation is modeled by mass burning equations instead of as an instantaneous process. Input to ZMOTTO is determined by the model chosen. Thermodynamic data is required for all models. Transport properties and chemical kinetics data are required only as the model complexity grows. Other input includes engine geometry, working fluid composition, operating characteristics, and intake/exhaust data. ZMOTTO accommodates a broad spectrum of reactants. The program will calculate many Otto cycle performance parameters for a number of consecutive cycles (a cycle being an interval of 720 crankangle degrees). A typical case will have a number of initial ideal cycles and progress through levels

  18. Characterisation of wood combustion ashes

    DEFF Research Database (Denmark)

    Maresca, Alberto

    The combustion of wood chips and wood pellets for the production of renewable energy in Denmark increased from 5.7 PJ to 16 PJ during the period 2000-2015, and further increases are expected to occur within the coming years. In 2012, about 22,300 tonnes of wood ashes were generated in Denmark....... Currently, these ashes are mainly landfilled, despite Danish legislation allowing their application onto forest and agricultural soils for fertilising and/or liming purposes. During this PhD work, 16 wood ash samples generated at ten different Danish combustion plants were collected and characterised...... for their composition and leaching properties. Despite the relatively large variations in the contents of nutrients and trace metals, the overall levels were comparable to typical ranges reported in the literature for other wood combustion ashes, as well as with regards to leaching. In general, the composition...

  19. Novel Active Combustion Control Valve

    Science.gov (United States)

    Caspermeyer, Matt

    2014-01-01

    This project presents an innovative solution for active combustion control. Relative to the state of the art, this concept provides frequency modulation (greater than 1,000 Hz) in combination with high-amplitude modulation (in excess of 30 percent flow) and can be adapted to a large range of fuel injector sizes. Existing valves often have low flow modulation strength. To achieve higher flow modulation requires excessively large valves or too much electrical power to be practical. This active combustion control valve (ACCV) has high-frequency and -amplitude modulation, consumes low electrical power, is closely coupled with the fuel injector for modulation strength, and is practical in size and weight. By mitigating combustion instabilities at higher frequencies than have been previously achieved (approximately 1,000 Hz), this new technology enables gas turbines to run at operating points that produce lower emissions and higher performance.

  20. Kinetics in Gas Mixtures for Problem of Plasma Assisted Combustion

    Science.gov (United States)

    2010-05-01

    precautions: in the case of relatively low elec- tron density, as it is realized for N2 or for O2, non–zero background due to accumulation of residual electron...and Lave L B 2003 Evaluating automobile fuel/propulsion system technologies Progress in Energy and Combustion Science 29 (2003) 1--69 [11] Polak L S...43 79—110 [41] Janev R K and Reiter D 2004 Collision processes of C2,3Hy and C2,3H + y hydrocarbons with electrons and protons Phys. Plasmas 11 780—829

  1. Ignition and combustion of sodium, fire consequences, extinguishment and prevention

    International Nuclear Information System (INIS)

    Malet, J.C.

    1996-01-01

    This document presents the results of work carried out at the IPSN on: sodium inflammation, sodium combustion (pool fires and sprayed jet fires), extinguishment (passive means and extinguishing powder), the physico-chemical behaviour of aerosols and their filtration, the protection means of concretes, intervention during and after a fire, treatment of residues, intervention equipment. The calculation codes developed during these studies are described. The experimental basis which allowed the qualification of these codes and the technological means aimed at prevention and sodium fire fighting, was obtained using programmes carried out in the experimental facilities existing in Cadarache or in collaboration with the German teams of Karlsruhe

  2. Ignition and combustion of sodium, fire consequences, extinguishment and prevention

    Energy Technology Data Exchange (ETDEWEB)

    Malet, J C [Institut de Protection et de Surete Nucleaire, Laboratoire d' Experimentation de Modelisation des Feux, C.E. Cadarache, Saint-Paul-lez-Durance (France). E-mail: malet at ipsncad.cea.fr

    1996-07-01

    This document presents the results of work carried out at the IPSN on: sodium inflammation, sodium combustion (pool fires and sprayed jet fires), extinguishment (passive means and extinguishing powder), the physico-chemical behaviour of aerosols and their filtration, the protection means of concretes, intervention during and after a fire, treatment of residues, intervention equipment. The calculation codes developed during these studies are described. The experimental basis which allowed the qualification of these codes and the technological means aimed at prevention and sodium fire fighting, was obtained using programmes carried out in the experimental facilities existing in Cadarache or in collaboration with the German teams of Karlsruhe.

  3. Combustion instability modeling and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Santoro, R.J.; Yang, V.; Santavicca, D.A. [Pennsylvania State Univ., University Park, PA (United States); Sheppard, E.J. [Tuskeggee Univ., Tuskegee, AL (United States). Dept. of Aerospace Engineering

    1995-12-31

    It is well known that the two key elements for achieving low emissions and high performance in a gas turbine combustor are to simultaneously establish (1) a lean combustion zone for maintaining low NO{sub x} emissions and (2) rapid mixing for good ignition and flame stability. However, these requirements, when coupled with the short combustor lengths used to limit the residence time for NO formation typical of advanced gas turbine combustors, can lead to problems regarding unburned hydrocarbons (UHC) and carbon monoxide (CO) emissions, as well as the occurrence of combustion instabilities. The concurrent development of suitable analytical and numerical models that are validated with experimental studies is important for achieving this objective. A major benefit of the present research will be to provide for the first time an experimentally verified model of emissions and performance of gas turbine combustors. The present study represents a coordinated effort between industry, government and academia to investigate gas turbine combustion dynamics. Specific study areas include development of advanced diagnostics, definition of controlling phenomena, advancement of analytical and numerical modeling capabilities, and assessment of the current status of our ability to apply these tools to practical gas turbine combustors. The present work involves four tasks which address, respectively, (1) the development of a fiber-optic probe for fuel-air ratio measurements, (2) the study of combustion instability using laser-based diagnostics in a high pressure, high temperature flow reactor, (3) the development of analytical and numerical modeling capabilities for describing combustion instability which will be validated against experimental data, and (4) the preparation of a literature survey and establishment of a data base on practical experience with combustion instability.

  4. Effect of Thymus vulgaris and Bunium persicum essential oils on the oxidative stability of virgin olive oil; Efecto de aceites esenciales de tomillo y comino negro sobre la estabilidad oxidativa de aceites de oliva virgen

    Energy Technology Data Exchange (ETDEWEB)

    Keramat, M.; Golmakani, M.T.

    2016-07-01

    Natural antioxidants are becoming a major focus because natural food ingredients are safer than synthetic types. The aim of this study was to investigate the protective effects of Thymus vulgaris and Bunium persicum essential oils (EO) on the oxidation of virgin olive oil (VOO) during accelerated storage. The antioxidant activities of EOs were compared with those of α-tocopherol and BHT. GC/MS analyses revealed that thymol (28.50%), p-cymene (27.14%), carvacrol (18.36%), and γ-terpinene (4.97%) are the main components of T. vulgaris EO, while cuminaldehyde (32.81%), γ-terpinene (16.02%) and p-cymene (14.07%) are the main components of B. persicum EO. Both EOs provided protection for the VOO, inhibiting the formation of primary and secondary oxidation products although T. vulgaris EO showed greater protection against the oxidation process than B. persicum EO. The effect of T. vulgaris essential oil on the oxidation inhibition of VOO was similar to that of BHT. α-Tocopherol showed no measurable effect on improving the oxidative stability of VOO. This study suggests that T. vulgaris and B. persicum EOs can be used to improve the oxidative stability of VOO. [Spanish] En los antioxidantes naturales se está centrando actualmente más la atención dado que los ingredientes naturales son más seguros que los sintéticos. El objetivo de este estudio fue estudiar el efecto protector de aceites esenciales (AE) de tomillo y comino negro en la oxidación del aceite de oliva virgen (AOV) durante un almacenamiento acelerado. Las actividades antioxidantes de los AE se compararon con las del α-tocoferol y BHT. Los análisis de GC/MS mostraron que timol (28,50%), p-cimeno (27,14%), carvacrol (18,36%), y γ-terpineno (4,97%) son los principales componentes de AE de tomillo, mientras que cuminaldehido (32,81%), γ-terpineno (16,02%) y p-cimeno (14,07%) lo son de AE de comino negro. Ambos AE proporcionan protección al AOV, inhibiendo la formación de productos de oxidaci

  5. Improvement of fuel combustion technologies

    Energy Technology Data Exchange (ETDEWEB)

    Tumanovskii, A.G.; Babii, V.I.; Enyakin, Y.P.; Kotler, V.R.; Ryabov, G.V.; Verbovetskii, E.K.; Nadyrov, I.I. [All-Russian Thermal Engineering Institute, Moscow (Russian Federation)

    1996-07-01

    The main problems encountered in the further development of fuel combustion technologies at thermal power stations in Russia are considered. Experience is generalized and results are presented on the efficiency with which nitrogen oxide emissions are reduced by means of technological methods when burning natural gas, fuel oil, and coal. The problems that arise in the introduction of new combustion technologies and in using more promising grades of coal are considered. The results studies are presented that show that low grade Russian coals can be burnt in circulating fluidized bed boilers. 14 refs., 5 figs., 4 tabs.

  6. Chemical kinetics and combustion modeling

    Energy Technology Data Exchange (ETDEWEB)

    Miller, J.A. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    The goal of this program is to gain qualitative insight into how pollutants are formed in combustion systems and to develop quantitative mathematical models to predict their formation rates. The approach is an integrated one, combining low-pressure flame experiments, chemical kinetics modeling, theory, and kinetics experiments to gain as clear a picture as possible of the process in question. These efforts are focused on problems involved with the nitrogen chemistry of combustion systems and on the formation of soot and PAH in flames.

  7. Cytotoxic and genotoxic responses of human lung cells to combustion smoke particles of Miscanthus straw, softwood and beech wood chips

    Science.gov (United States)

    Arif, Ali Talib; Maschowski, Christoph; Garra, Patxi; Garcia-Käufer, Manuel; Petithory, Tatiana; Trouvé, Gwenaëlle; Dieterlen, Alain; Mersch-Sundermann, Volker; Khanaqa, Polla; Nazarenko, Irina; Gminski, Richard; Gieré, Reto

    2017-08-01

    Inhalation of particulate matter (PM) from residential biomass combustion is epidemiologically associated with cardiovascular and pulmonary diseases. This study investigates PM0.4-1 emissions from combustion of commercial Miscanthus straw (MS), softwood chips (SWC) and beech wood chips (BWC) in a domestic-scale boiler (40 kW). The PM0.4-1 emitted during combustion of the MS, SWC and BWC were characterized by ICP-MS/OES, XRD, SEM, TEM, and DLS. Cytotoxicity and genotoxicity in human alveolar epithelial A549 and human bronchial epithelial BEAS-2B cells were assessed by the WST-1 assay and the DNA-Alkaline Unwinding Assay (DAUA). PM0.4-1 uptake/translocation in cells was investigated with a new method developed using a confocal reflection microscope. SWC and BWC had a inherently higher residual water content than MS. The PM0.4-1 emitted during combustion of SWC and BWC exhibited higher levels of Polycyclic Aromatic Hydrocarbons (PAHs), a greater variety of mineral species and a higher heavy metal content than PM0.4-1 from MS combustion. Exposure to PM0.4-1 from combustion of SWC and BWC induced cytotoxic and genotoxic effects in human alveolar and bronchial cells, whereby the strongest effect was observed for BWC and was comparable to that caused by diesel PM (SRM 2 975), In contrast, PM0.4-1 from MS combustion did not induce cellular responses in the studied lung cells. A high PAH content in PM emissions seems to be a reliable chemical marker of both combustion efficiency and particle toxicity. Residual biomass water content strongly affects particulate emissions and their toxic potential. Therefore, to minimize the harmful effects of fine PM on health, improvement of combustion efficiency (aiming to reduce the presence of incomplete combustion products bound to PM) and application of fly ash capture technology, as well as use of novel biomass fuels like Miscanthus straw is recommended.

  8. Application of the FIRST Combustion model to Spray Combustion

    NARCIS (Netherlands)

    de Jager, B.; Kok, Jacobus B.W.

    2004-01-01

    Liquid fuel is of interest to apply to gas turbines. The large advantage is that liquids are easily storable as compared to gaseous fuels. Disadvantage is that liquid fuel has to be sprayed, vaporized and mixed with air. Combustion occurs at some stage of mixing and ignition. Depending on the

  9. Development of a Premixed Combustion Capability for Scramjet Combustion Experiments

    Science.gov (United States)

    Rockwell, Robert D.; Goyne, Christopher P.; Rice, Brian E.; Chelliah, Harsha; McDaniel, James C.; Edwards, Jack R.; Cantu, Luca M. L.; Gallo, Emanuela C. A.; Cutler, Andrew D.; Danehy, Paul M.

    2015-01-01

    Hypersonic air-breathing engines rely on scramjet combustion processes, which involve high speed, compressible, and highly turbulent flows. The combustion environment and the turbulent flames at the heart of these engines are difficult to simulate and study in the laboratory under well controlled conditions. Typically, wind-tunnel testing is performed that more closely approximates engine testing rather than a careful investigation of the underlying physics that drives the combustion process. The experiments described in this paper, along with companion data sets being developed separately, aim to isolate the chemical kinetic effects from the fuel-air mixing process in a dual-mode scramjet combustion environment. A unique fuel injection approach is taken that produces a nearly uniform fuel-air mixture at the entrance to the combustor. This approach relies on the precombustion shock train upstream of the dual-mode scramjet combustor. A stable ethylene flame anchored on a cavity flameholder with a uniformly mixed combustor inflow has been achieved in these experiments allowing numerous companion studies involving coherent anti-Stokes Raman scattering (CARS), particle image velocimetry (PIV), and planar laser induced fluorescence (PLIF) to be performed.

  10. Análisis de viabilidad técnica y económica de implantación de un sistema de obtención de biocombustible a partir de aceite usado

    OpenAIRE

    Montesinos López, Rubén

    2012-01-01

    Este proyecto se centrará en el aprovechamiento del aceite vegetal usado como fuente de biomasa para la producción de biodiesel, un tipo de biocombustible, como alternativa a la utilización de aceites procedentes de cultivos energéticos. Se tratará de hacer una revisión del estado del arte en el ámbito de la biomasa y más concretamente en el ámbito del biodiesel. Se estudiará la tecnología relacionada con la producción de biodiesel, así como la decisión de elegir el aceite vege...

  11. Fumigant Toxicity of some Essential Oils on Adults of some Stored-Product Pests Toxicidad Fumigante de Algunos Aceites Esenciales sobre Adultos de algunas Plagas de Productos Almacenados

    Directory of Open Access Journals (Sweden)

    Mohammad Mahmoudvand

    2011-03-01

    Full Text Available Plant materials with insecticidal properties have been traditionally used for generations in some parts of the world. In this study, fumigant toxicity of some essential oils extracted from Rosmarinus officinalis L., Mentha pulegium L., Zataria multiflora, and Citrus sinensis (L. Osbeck var. hamlin on adults of stored-product pests, including Tribolium castaneum, Sitophilus granarius, Callosobruchus maculatus, and Plodia interpunctella were investigated. Pure essential oils were used in glass vials for the bioassay. LC50 values of Citrus sinensis var. hamlin against T. castaneum, S. granarius, and C. maculatus were 391.28, 367.75, and 223.48 µL L-1 air after 24 h, 362.40, 20.45, and 207.17 µL L-1 air after 48 h, respectively. Furthermore, LC50 values of the fumigant test of C. sinensis and M. pulegium essential oils against S. granarius were 0.038 and 367.75 µL L-1 air after 24 h, 0.025 and 320.45 µL L-1 air after 48 h, respectively. On the other hand, LC50 values of R. officinalis and Z. multiflora on P. interpunctella moths were 0.93 and 1.75 µL L-1 after 24 h. Results showed that among tested essential oils, C. sinensis var. hamlin had good fumigant toxicity on T. castaneum, S. granarius, and C. maculatus. In addition, M. pulegium essential oil was stronger than C. sinensis var. hamlin on S. granarius. Results also indicated that both Z. multiflora and R. officinalis had fumigant toxicity on P. interpunctella adults. In summary, results indicated that these essential oils have good fumigant toxicity on stored-product pests.Materiales vegetales con propiedades insecticidas han sido usados tradicionalmente por generaciones en algunas partes del mundo. En este estudio se estudió la toxicidad fumigante de algunos aceites esenciales extraídos desde Rosmarinus officinalis L., Mentha pulegium L., Zataria multiflora y Citrus sinensis (L. Osbeck var. hamlin sobre adultos de plagas de productos almacenados, incluyendo Tribolium castaneum

  12. Interactive wood combustion for botanical tree models

    KAUST Repository

    Pirk, Sö ren; Jarząbek, Michał; Hadrich, Torsten; Michels, Dominik L.; Palubicki, Wojciech

    2017-01-01

    We present a novel method for the combustion of botanical tree models. Tree models are represented as connected particles for the branching structure and a polygonal surface mesh for the combustion. Each particle stores biological and physical

  13. Free Energy and Internal Combustion Engine Cycles

    OpenAIRE

    Harris, William D.

    2012-01-01

    The performance of one type (Carnot) of Internal Combustion Engine (ICE) cycle is analyzed within the framework of thermodynamic free energies. ICE performance is different from that of an External Combustion Engine (ECE) which is dictated by Carnot's rule.

  14. Method for storing radioactive combustible waste

    Science.gov (United States)

    Godbee, H.W.; Lovelace, R.C.

    1973-10-01

    A method is described for preventing pressure buildup in sealed containers which contain radioactively contaminated combustible waste material by adding an oxide getter material to the container so as to chemically bind sorbed water and combustion product gases. (Official Gazette)

  15. Scramjet Combustion Stability Behavior Modeling, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — A recent breakthrough in combustion stability analysis (UCDS) offers the potential to predict the combustion stability of a scramjet. This capability is very...

  16. Scramjet Combustion Stability Behavior Modeling, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — A recent breakthrough in combustion stability analysis (UCDS) offers the means to accurately predict the combustion stability of a scramjet. This capability is very...

  17. Publication sites productive uses of combustion ash

    Science.gov (United States)

    Publication Sites Productive Uses of Combustion Ash For more information contact: e:mail: Public waste combustion ash in landfills. The new technology brief describes recent studies where ash was used

  18. Combustion Research Facility | A Department of Energy Office of Science

    Science.gov (United States)

    Collaborative Research Facility Back to Sandia National Laboratory Homepage Combustion Research Search the CRF Combustion Chemistry Flame Chemistry Research.Combustion_Chemistry.Flame_Chemistry Theory and Modeling Theory and Modeling Combustion Kinetics High Pressure Chemistry Chemistry of Autoignition

  19. Fuel Combustion and Engine Performance | Transportation Research | NREL

    Science.gov (United States)

    Fuel Combustion and Engine Performance Fuel Combustion and Engine Performance Photo of a gasoline emissions in advanced engine technologies. Photo by Dennis Schroeder, NREL NREL's combustion research and combustion and engine research activities include: Developing experimental and simulation research platforms

  20. Efecto de la suplementación con aceite de pescado sobre la frecuencia cardíaca y temperatura rectal en perros sanos durante un programa de entrenamiento en cinta trotadora

    Directory of Open Access Journals (Sweden)

    Francisco Javier Pellegrino

    2017-05-01

    Full Text Available El objetivo del presente estudio fue evaluar el efecto de la suplementación con aceite de pescado sobre la frecuencia cardíaca y temperatura rectal en perros sanos durante un programa de entrenamiento en cinta trotadora. En un diseño experimental cruzado, 5 perros machos fueron asignados aleatoriamente a los grupos control y aceite de pescado, y recibieron diariamente 54 mg de aceite de pescado/kg de peso corporal0,75. Todos fueron entrenados en cinta trotadora dos veces por semana durante 12 semanas. Cada sesión incluyó un total de 30 minutos a 8 km/h y 7,5 % de pendiente. Se evaluó la frecuencia cardíaca previa, inmediatamente posterior y a los 5 minutos de finalizada cada sesión de entrenamiento. Se midió la temperatura rectal previa y posterior a cada sesión. En el grupo aceite de pescado, la frecuencia cardíaca y temperatura rectal posteriores a cada sesión de entrenamiento disminuyeron significativamente (P0,1. Los resultados obtenidos podrían reflejar una mejora en el rendimiento en perros suplementados con aceite de pescado durante el entrenamiento en cinta trotadora. Sin embargo, sería interesante realizar más estudios que permitan explicar los mecanismos por los cuales la suplementación con aceite de pescado podría mejorar el rendimiento en entrenamiento.