Lift truck safety review

Energy Technology Data Exchange (ETDEWEB)

Cadwallader, L.C.

1997-03-01

This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter`s Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given.

Lift truck safety review

International Nuclear Information System (INIS)

Cadwallader, L.C.

1997-03-01

This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter's Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given

A microcomputer-based model for identifying urban and suburban roadways with critical large truck accident rates

International Nuclear Information System (INIS)

Brogan, J.D.; Cashwell, J.W.

1992-01-01

This paper presents an overview of techniques for merging highway accident record and roadway inventory files and employing the combined data set to identify spots or sections on highway facilities in urban and suburban areas with unusually high large truck accident rates. A statistical technique, the rate/quality control method, is used to calculate a critical rate for each location of interest. This critical rate may then be compared to the location's actual accident rate to identify locations for further study. Model enhancements and modifications are described to enable the technique to be employed in the evaluation of routing alternatives for the transport of radioactive material

Guidance on accidents involving radioactivity

International Nuclear Information System (INIS)

1989-01-01

This annex contains advice to Health Authorities on their response to accidents involving radioactivity. The guidance is in six parts:-(1) planning the response required to nuclear accidents overseas, (2) planning the response required to UK nuclear accidents a) emergency plans for nuclear installations b) nuclear powered satellites, (3) the handling of casualties contaminated with radioactive substances, (4) background information for dealing with queries from the public in the event of an accident, (5) the national arrangements for incident involving radioactivity (NAIR), (6) administrative arrangements. (author)

Application of Latin hypercube sampling to RADTRAN 4 truck accident risk sensitivity analysis

International Nuclear Information System (INIS)

Mills, G.S.; Neuhauser, K.S.; Kanipe, F.L.

1994-01-01

The sensitivity of calculated dose estimates to various RADTRAN 4 inputs is an available output for incident-free analysis because the defining equations are linear and sensitivity to each variable can be calculated in closed mathematical form. However, the necessary linearity is not characteristic of the equations used in calculation of accident dose risk, making a similar tabulation of sensitivity for RADTRAN 4 accident analysis impossible. Therefore, a study of sensitivity of accident risk results to variation of input parameters was performed using representative routes, isotopic inventories, and packagings. It was determined that, of the approximately two dozen RADTRAN 4 input parameters pertinent to accident analysis, only a subset of five or six has significant influence on typical analyses or is subject to random uncertainties. These five or six variables were selected as candidates for Latin Hypercube Sampling applications. To make the effect of input uncertainties on calculated accident risk more explicit, distributions and limits were determined for two variables which had approximately proportional effects on calculated doses: Pasquill Category probability (PSPROB) and link population density (LPOPD). These distributions and limits were used as input parameters to Sandia's Latin Hypercube Sampling code to generate 50 sets of RADTRAN 4 input parameters used together with point estimates of other necessary inputs to calculate 50 observations of estimated accident dose risk.Tabulations of the RADTRAN 4 accident risk input variables and their influence on output plus illustrative examples of the LHS calculations, for truck transport situations that are typical of past experience, will be presented

Advanced vehicle dynamics of heavy trucks with the perspective of road safety

Science.gov (United States)

Trigell, Annika Stensson; Rothhämel, Malte; Pauwelussen, Joop; Kural, Karel

2017-10-01

This paper presents state-of-the art within advanced vehicle dynamics of heavy trucks with the perspective of road safety. The most common accidents with heavy trucks involved are truck against passenger cars. Safety critical situations are for example loss of control (such as rollover and lateral stability) and a majority of these occur during speed when cornering. Other critical situations are avoidance manoeuvre and road edge recovery. The dynamic behaviour of heavy trucks have significant differences compared to passenger cars and as a consequence, successful application of vehicle dynamic functions for enhanced safety of trucks might differ from the functions in passenger cars. Here, the differences between vehicle dynamics of heavy trucks and passenger cars are clarified. Advanced vehicle dynamics solutions with the perspective of road safety of trucks are presented, beginning with the topic vehicle stability, followed by the steering system, the braking system and driver assistance systems that differ in some way from that of passenger cars as well.

Papers on vehicle size : cars and trucks

Science.gov (United States)

1988-06-01

The four papers in this volume describe analyses of car size : trends and truck occupant injuries and fatalities. All four were : written between June 1985 and December 1987. The topics : addressed include where heavy truck accidents occur, injury an...

Severities of transportation accidents involving large packages

Energy Technology Data Exchange (ETDEWEB)

Dennis, A.W.; Foley, J.T. Jr.; Hartman, W.F.; Larson, D.W.

1978-05-01

The study was undertaken to define in a quantitative nonjudgmental technical manner the abnormal environments to which a large package (total weight over 2 tons) would be subjected as the result of a transportation accident. Because of this package weight, air shipment was not considered as a normal transportation mode and was not included in the study. The abnormal transportation environments for shipment by motor carrier and train were determined and quantified. In all cases the package was assumed to be transported on an open flat-bed truck or an open flat-bed railcar. In an earlier study, SLA-74-0001, the small-package environments were investigated. A third transportation study, related to the abnormal environment involving waterways transportation, is now under way at Sandia Laboratories and should complete the description of abnormal transportation environments. Five abnormal environments were defined and investigated, i.e., fire, impact, crush, immersion, and puncture. The primary interest of the study was directed toward the type of large package used to transport radioactive materials; however, the findings are not limited to this type of package but can be applied to a much larger class of material shipping containers.

Severities of transportation accidents involving large packages

International Nuclear Information System (INIS)

Dennis, A.W.; Foley, J.T. Jr.; Hartman, W.F.; Larson, D.W.

1978-05-01

The study was undertaken to define in a quantitative nonjudgmental technical manner the abnormal environments to which a large package (total weight over 2 tons) would be subjected as the result of a transportation accident. Because of this package weight, air shipment was not considered as a normal transportation mode and was not included in the study. The abnormal transportation environments for shipment by motor carrier and train were determined and quantified. In all cases the package was assumed to be transported on an open flat-bed truck or an open flat-bed railcar. In an earlier study, SLA-74-0001, the small-package environments were investigated. A third transportation study, related to the abnormal environment involving waterways transportation, is now under way at Sandia Laboratories and should complete the description of abnormal transportation environments. Five abnormal environments were defined and investigated, i.e., fire, impact, crush, immersion, and puncture. The primary interest of the study was directed toward the type of large package used to transport radioactive materials; however, the findings are not limited to this type of package but can be applied to a much larger class of material shipping containers

Assessment of the risk of transporting spent nuclear fuel by truck

International Nuclear Information System (INIS)

Elder, H.K.

1978-11-01

The assessment includes the risks from release of spent fuel materials and radioactive cask cavity cooling water due to transportation accidents. The contribution to the risk of package misclosure and degradation during normal transport was also considered. The results of the risk assessment have been related to a time in the mid-1980's, when it is projected that nuclear plants with an electrical generating capacity of 100 GW will be operating in the U.S. For shipments from reactors to interim storage facilities, it is estimated that a truck carrying spent fuel will be involved in an accident that would not be severe enough to result in a release of spent fuel material about once in 1.1 years. It was estimated that an accident that could result in a small release of radioactive material (primarily contaminated cooling water) would occur once in about 40 years. The frequency of an accident resulting in one or more latent cancer fatalities from release of radioactive materials during a truck shipment of spent fuel to interim storage was estimated to be once in 41,000 years. No accidents were found that would result in acute fatalities from releases of radioactive material. The risk for spent fuel shipments from reactors to reprocessing plants was found to be about 20% less than the risk for shipments to interim storage. Although the average shipment distance for the reprocessing case is larger, the risk is somewhat lower because the shipping routes, on average, are through less populated sections of the country. The total risk from transporting 180-day cooled spent fuel by truck in the reference year is 4.5 x 10 -5 fatalities. An individual in the population at risk would have one chance in 6 x 10 11 of suffering a latent cancer fatality from a release of radioactive material from a truck carrying spent fuel in the reference year

Road accidents involving bicycles: configurations and injuries.

Science.gov (United States)

Orsi, Chiara; Montomoli, Cristina; Otte, Dietmar; Morandi, Anna

2017-12-01

This study analyzed the most common types of accident involving bicycles and compared the frequency of injuries. The data source was the database of German In-Depth Accident Study (GIDAS). Cases consist of bicycles and their riders involved in accidents between 2000 and 2010. In most collisions, the bicycle impacted with a car. The percentage of injured bicyclists was higher in collisions with a heavy vehicle and decreased when the bicycle impacted with lighter vehicles. A high percentage of injured bicyclists in single accidents was observed; the most severe injury was more frequently to head and extremities. Accidents involving a car and a bicycle with the right of way in a bicycle path represented about 20% of involved and injured bicyclists. The ten most frequent configurations represented about 60% of involved and injured bicyclists. These results contribute to understand the dangerous scenarios for bicyclists and to suggest preventive actions.

Frontal collisions between trucks and cars : the Dutch contribution to Phase A (Accident data and statistics) of EEVC Working Group 14 "Development of a test procedure for energy-absorbing front underrun protection systems for trucks".

NARCIS (Netherlands)

Schoon, C.C.

1994-01-01

This study investigates both the frequency and seriousness of particularly the frontal collisions between trucks and cars. The study is the Dutch contribution to phase A (accident data and statistics) of the research programme of the European Experimental Vehicles Committee (EEVC) Working Group 14.

ANFO truck burn trials

Energy Technology Data Exchange (ETDEWEB)

Rosen von, B.; Contestabile, E. [Natural Resources Canada, CANMET Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

2003-10-01

This report describes the investigation of a tractor-trailer explosion. A truck loaded with 18,000 kg of commercial explosives, of which 13,000 kg was ammonium nitrate with fuel oil (ANFO), caught fire when it struck a rockcut near Walden, Ontario on August 5, 1998. The fire resulted in the detonation of the load. The Canadian Explosives Research Laboratory (CERL) conducted a test program to examine the suitability of existing explosive transportation regulations. Unconfined burns of ANFO were performed. The accident was recreated in two burn trials in an attempt to identify the mechanism that led from fire to detonation. Two full-scale tests were conducted using complete tractor-trailers, each in a jack-knifed position with most of the explosives placed on the ground in front of the trailer. ANFO was used in the first test to determine its response to thermal stimulus and the likelihood of detonation or explosion. The second test involved ANFO, a slurry and an emulsion. Thermocouples and video cameras were used to observe the burning characteristics of the explosives, the truck and its components. The explosives burned steadily for 80 minutes in each test. Many truck components, such as tires, spring brake chambers and the fuel tank ruptured violently due to the heat. Although no detonation occurred in the test trials, it was concluded that under favourable conditions, many truck components, might produce fragments with enough energy to initiate heat-sensitized explosives. It was suggested that a fragment impact caused the detonation at Walden. 4 refs., 7 tabs., 8 figs.

Dose estimates in a loss of lead shielding truck accident.

Energy Technology Data Exchange (ETDEWEB)

Dennis, Matthew L.; Osborn, Douglas M.; Weiner, Ruth F.; Heames, Terence John (Alion Science & Technology Albuquerque, NM)

2009-08-01

The radiological transportation risk & consequence program, RADTRAN, has recently added an updated loss of lead shielding (LOS) model to it most recent version, RADTRAN 6.0. The LOS model was used to determine dose estimates to first-responders during a spent nuclear fuel transportation accident. Results varied according to the following: type of accident scenario, percent of lead slump, distance to shipment, and time spent in the area. This document presents a method of creating dose estimates for first-responders using RADTRAN with potential accident scenarios. This may be of particular interest in the event of high speed accidents or fires involving cask punctures.

Buses involved in fatal accidents factbook 2007

Science.gov (United States)

2010-03-01

This document presents aggregate statistics on buses involved in traffic accidents in 2007. The : statistics are derived from the Buses Involved in Fatal Accidents (BIFA) file, compiled by the : University of Michigan Transportation Research Institut...

Review and assessment of package requirements (yellowcake) and emergency response to transportation accidents

International Nuclear Information System (INIS)

1978-10-01

As a consequence of an accident involving a truck shipment of yellowcake, a joint NRC--DOT study was undertaken to review and assess the regulations and practices related to package integrity and to emergency response to transportation accidents involving low specific activity radioactive materials. Recommendations are made regarding the responsibilities of state and local agencies, carriers, and shippers, and the DOT and NRC regulations

Probability of spent fuel transportation accidents

International Nuclear Information System (INIS)

McClure, J.D.

1981-07-01

The transported volume of spent fuel, incident/accident experience and accident environment probabilities were reviewed in order to provide an estimate of spent fuel accident probabilities. In particular, the accident review assessed the accident experience for large casks of the type that could transport spent (irradiated) nuclear fuel. This review determined that since 1971, the beginning of official US Department of Transportation record keeping for accidents/incidents, there has been one spent fuel transportation accident. This information, coupled with estimated annual shipping volumes for spent fuel, indicated an estimated annual probability of a spent fuel transport accident of 5 x 10 -7 spent fuel accidents per mile. This is consistent with ordinary truck accident rates. A comparison of accident environments and regulatory test environments suggests that the probability of truck accidents exceeding regulatory test for impact is approximately 10 -9 /mile

Review of US accident/incident experience involving the transportation of radioactive material (RAM) 1971-1980

International Nuclear Information System (INIS)

McClure, J.D.; Emerson, E.L.

1980-01-01

This paper analyzes the transportation accidents and incidents which have occurred in the United States in the period 1971-1980 based upon the information in the Radioactive Material Transportation Accident/Incident Data Base developed by the Transportation Technology Center (TTC) at Sandia National Laboratories. The accident/incident data base incorporates the files of the Hazardous Material Incident Report (HMIR) system operated by the Material Transportation Bureau of the US Department of Transportation (DOT) with additional information obtained from the files of the US Nuclear Regulatory Commission (NRC). A principal objective of this paper is to summarize US accident/incident experience for the past ten years, providing a concise statement of radioactive material (RAM) package failure description for the transport modes of truck, rail and air

Traffic accidents involving fatigue driving and their extent of casualties.

Science.gov (United States)

Zhang, Guangnan; Yau, Kelvin K W; Zhang, Xun; Li, Yanyan

2016-02-01

The rapid progress of motorization has increased the number of traffic-related casualties. Although fatigue driving is a major cause of traffic accidents, the public remains not rather aware of its potential harmfulness. Fatigue driving has been termed as a "silent killer." Thus, a thorough study of traffic accidents and the risk factors associated with fatigue-related casualties is of utmost importance. In this study, we analyze traffic accident data for the period 2006-2010 in Guangdong Province, China. The study data were extracted from the traffic accident database of China's Public Security Department. A logistic regression model is used to assess the effect of driver characteristics, type of vehicles, road conditions, and environmental factors on fatigue-related traffic accident occurrence and severity. On the one hand, male drivers, trucks, driving during midnight to dawn, and morning rush hours are identified as risk factors of fatigue-related crashes but do not necessarily result in severe casualties. Driving at night without street-lights contributes to fatigue-related crashes and severe casualties. On the other hand, while factors such as less experienced drivers, unsafe vehicle status, slippery roads, driving at night with street-lights, and weekends do not have significant effect on fatigue-related crashes, yet accidents associated with these factors are likely to have severe casualties. The empirical results of the present study have important policy implications on the reduction of fatigue-related crashes as well as their severity. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Polytrauma following a truck accident : How to save lives by guideline-oriented emergency care].

Science.gov (United States)

Kippnich, M; Jelting, Y; Markus, C; Kredel, M; Wurmb, T; Kranke, P

2017-12-01

Identification and immediate treatment of life-threatening conditions is fundamental in patients with multiple trauma. In this context, the S3 guidelines on polytrauma and the S1 guidelines on emergency anesthesia provide the scientific background on how to handle these situations. This case report deals with a seriously injured driver involved in a truck accident. The inaccessible patient showed a scalping injury of the facial skeleton with massive bleeding and partially blocked airway but with spontaneous breathing as well as centralized cardiovascular circulation conditions and an initial Glasgow coma scale (GCS) of 8. An attempt was made to stop the massive bleeding by using hemostyptic-coated dressings. In addition, the patient was intubated via video laryngoscopy and received a left and right thoracic drainage as well as two entry points for intraosseous infusion. In modern emergency medical services, treatment based on defined algorithms is recommended and also increasingly established in dealing with critical patients. The guideline-oriented emergency care of patients with polytrauma requires invasive measures, such as intubation and thoracic decompression in the preclinical setting. The foundation for this procedure includes training in theory and practice both of the non-medical and medical rescue service personnel.

Prevalence of drugs in oral fluid from truck drivers in Brazilian highways.

Science.gov (United States)

Bombana, Henrique Silva; Gjerde, Hallvard; Dos Santos, Marcelo Filonzi; Jamt, Ragnhild Elén Gjulem; Yonamine, Mauricio; Rohlfs, Waldo José Caram; Muñoz, Daniel Romero; Leyton, Vilma

2017-04-01

Traffic accidents are responsible for 1.25 million deaths worldwide and are the most common cause of death among those aged 15-29 years. In Brazil, traffic accidents caused more than 44,000 deaths in 2014. The use of psychoactive drugs is an important risk factor for being involved in traffic accidents. Previous studies have found that psychoactive substances are commonly used by truck drivers in Brazil to maintain their extensive work schedule and stay awake while driving during nighttime hours. The state of Sao Paulo is one of the most important states regarding goods transportation. Important highways cross through Sao Paulo to other regions from Brazil and to other countries in Latin America. This study aims to determine the prevalence of illicit drug use by truck drivers in the state of Sao Paulo through toxicological analyses of oral fluid. Truck drivers were randomly stopped by police officers on federal roads during morning hours. Oral fluid samples were collected using the Quantisal™ device. In addition, a questionnaire concerning sociodemographic characteristics and health information was administered. Oral fluid samples were screened for amphetamine, cocaine, and tetrahydrocannabinol (Δ9-THC) by ELISA and the confirmation was performed using ultra performance liquid chromatography with tandem mass spectrometry detection (UPLC-MS/MS). Of the 764 drivers stopped, 762 agreed to participate. The participants were driving an average of 614km and 9.4h a day. Of the total samples, 5.2% (n=40) tested positive for drugs. Cocaine was the most frequently found drug (n=21), followed by amphetamine (n=16) and Δ9-THC (n=8). All drivers were men with an average age of 42.5 years. With these results we were able to verify that many truck drivers were still consuming psychoactive drugs while driving, and cocaine was the most prevalent one. This reinforces the need for preventive measures aimed at controlling the use of illicit drugs by truck drivers in Brazil

A comparison of the hazard perception ability of accident-involved and accident-free motorcycle riders.

Science.gov (United States)

Cheng, Andy S K; Ng, Terry C K; Lee, Hoe C

2011-07-01

Hazard perception is the ability to read the road and is closely related to involvement in traffic accidents. It consists of both cognitive and behavioral components. Within the cognitive component, visual attention is an important function of driving whereas driving behavior, which represents the behavioral component, can affect the hazard perception of the driver. Motorcycle riders are the most vulnerable types of road user. The primary purpose of this study was to deepen our understanding of the correlation of different subtypes of visual attention and driving violation behaviors and their effect on hazard perception between accident-free and accident-involved motorcycle riders. Sixty-three accident-free and 46 accident-involved motorcycle riders undertook four neuropsychological tests of attention (Digit Vigilance Test, Color Trails Test-1, Color Trails Test-2, and Symbol Digit Modalities Test), filled out the Chinese Motorcycle Rider Driving Violation (CMRDV) Questionnaire, and viewed a road-user-based hazard situation with an eye-tracking system to record the response latencies to potentially dangerous traffic situations. The results showed that both the divided and selective attention of accident-involved motorcycle riders were significantly inferior to those of accident-free motorcycle riders, and that accident-involved riders exhibited significantly higher driving violation behaviors and took longer to identify hazardous situations compared to their accident-free counterparts. However, the results of the regression analysis showed that aggressive driving violation CMRDV score significantly predicted hazard perception and accident involvement of motorcycle riders. Given that all participants were mature and experienced motorcycle riders, the most plausible explanation for the differences between them is their driving style (influenced by an undesirable driving attitude), rather than skill deficits per se. The present study points to the importance of

Emergency response to a highway accident in Springfield, Massachusetts, on December 16, 1991

International Nuclear Information System (INIS)

1992-06-01

On December 16, 1991, a truck carrying unirradiated (fresh) nuclear fuel was involved in an accident on US Interstate 91, in Springfield, Massachusetts. This report describes the emergency response measures undertaken by local, State, Federal, and private parties. The report also discusses ''lessons learned'' from the response to the accident and suggests areas where improvements might be made

Improving truck safety: Potential of weigh-in-motion technology

Directory of Open Access Journals (Sweden)

Bernard Jacob

2010-07-01

Full Text Available Trucks exceeding the legal mass limits increase the risk of traffic accidents and damage to the infrastructure. They also result in unfair competition between transport modes and companies. It is therefore important to ensure truck compliance to weight regulation. New technologies are being developed for more efficient overload screening and enforcement. Weigh-in-Motion (WIM technologies allow trucks to be weighed in the traffic flow, without any disruption to operations. Much progress has been made recently to improve and implement WIM systems, which can contribute to safer and more efficient operation of trucks.

The potential importance of water pathways for spent fuel transportation accident risk

International Nuclear Information System (INIS)

Ostmeyer, R.M.

1986-01-01

This paper analyzes the potential importance of water pathway contamination for spent fuel transportation accident risk using a ''worst-case'' water contamination scenario. The scenario used for the analysis involves an accident release that occurs near a reservoir. Water pathway doses are compared to doses for accident releases in urban or agricultural areas. The results of the analysis indicate that water pathways are not important for assessing the risk of transporting spent reactor fuel by truck or by rail

Occupational accidents involving biological material among public health workers.

Science.gov (United States)

Chiodi, Mônica Bonagamba; Marziale, Maria Helena Palucci; Robazzi, Maria Lúcia do Carmo Cruz

2007-01-01

This descriptive research aimed to recognize the occurrence of work accidents (WA) involving exposure to biological material among health workers at Public Health Units in Ribeirão Preto-SP, Brazil. A quantitative approach was adopted. In 2004, 155 accidents were notified by means of the Work Accident Communication (WAC). Sixty-two accidents (40%) involved exposure to biological material that could cause infections like Hepatitis and Aids. The highest number of victims (42 accidents) came from the category of nursing aids and technicians. Needles were responsible for 80.6% of accidents and blood was the biological material involved in a majority of occupational exposure cases. This subject needs greater attention, so that prevention measures can be implemented, which consider the peculiarities of the activities carried out by the different professional categories.

Prevalence of at-risk drinking among Brazilian truck drivers and its interference on the performance of executive cognitive tasks.

Science.gov (United States)

de Oliveira, Lucio Garcia; Leopoldo, Kae; Gouvea, Marcela Julio Cesar; Barroso, Lucia Pereira; Gouveia, Paula Adriana Rodrigues; Muñoz, Daniel Romero; Leyton, Vilma

2016-09-01

Binge drinking (BD) has been associated with an increase in the risk of alcohol-related injuries. Alcohol continues to be the main substance consumed by truck drivers, a population of special concern, since they are often involved in traffic accidents. The aim of this study was to estimate the prevalence of BD and its interference in the executive functioning among truck drivers in Sao Paulo, Brazil. A non-probabilistic sample of 684 truck drivers was requested to answer a structured research instrument on their demographic data and alcohol use. They performed cognitive tests to assess their executive functioning and inventories about confounding variables. The participants were then divided according to their involvement in BD. 17.5% of the interviewees have reported being engaged in BD. Binge drinkers showed a better performance on one test, despite having done so at the expense of more mistakes and lower accuracy. More interestingly, binge drinkers took three seconds longer than non-binge drinkers to inhibit an inadequate response, which is worrisome in the context of traffic. Overall, the deleterious effect of BD on performance remained after controlling for the effects of confounding variables in regression logistic models. As the use of alcohol among truck drivers may be as a way to get by with their work conditions, we believe that a negotiation between their work organization and public authorities would reduce such use, preventing negative interferences on truck drivers' cognitive functioning, which by its turn may also prevent traffic accidents. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Transport company safety climate - the impact on truck driver behaviour and crash involvement

OpenAIRE

Sullman, Mark J. M.; Stephens A. N.; Pajo K.

2017-01-01

Objective: The present study investigated the relationships between safety climate and driving behavior and crash involvement. Methods: A total of 339 company-employed truck drivers completed a questionnaire that measured their perceptions of safety climate, crash record, speed choice, and aberrant driving behaviors (errors, lapses, and violations). Results: Although there was no direct relationship between the drivers' perceptions of safety climate and crash involvement, safety clima...

Driving fatigue in professional drivers: a survey of truck and taxi drivers.

Science.gov (United States)

Meng, Fanxing; Li, Shuling; Cao, Lingzhi; Li, Musen; Peng, Qijia; Wang, Chunhui; Zhang, Wei

2015-01-01

Fatigue among truck drivers has been studied extensively; however, less is known regarding the fatigue experience of taxi drivers in heavily populated metropolitan areas. This study aimed to compare the differences and similarities between truck and taxi driver fatigue to provide implications for the fatigue management and education of professional drivers. A sample of 274 truck drivers and 286 taxi drivers in Beijing was surveyed via a questionnaire, which included items regarding work characteristics, fatigue experience, accident information, attitude toward fatigue, and methods of counteracting fatigue. Driver fatigue was prevalent among professional drivers, and it was even more serious for taxi drivers. Taxi drivers reported more frequent fatigue experiences and were involved in more accidents. Among the contributing factors to fatigue, prolonged driving time was the most important factor identified by both driver groups. Importantly, the reason for the engagement in prolonged driving was neither due to the lack of awareness concerning the serious outcome of fatigue driving nor because of their poor detection of fatigue. The most probable reason was the optimism bias, as a result of which these professional drivers thought that fatigue was more serious for other drivers than for themselves, and they thought that they were effective in counteracting the effect of fatigue on their driving performance. Moreover, truck drivers tended to employ methods that require stopping to counteract fatigue, whereas taxi drivers preferred methods that were simultaneous with driving. Although both driver groups considered taking a nap as one of the most effective means to address fatigue, this method was not commonly used. Interestingly, these drivers were aware that the methods they frequently used were not the most effective means to counteract fatigue. This study provides knowledge on truck and taxi drivers' characteristics in fatigue experience, fatigue attitude, and

49 CFR 234.7 - Accidents involving grade crossing signal failure.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Accidents involving grade crossing signal failure... PLANS Reports and Plans § 234.7 Accidents involving grade crossing signal failure. (a) Each railroad... (activation failure report) and 49 CFR 225.11 (accident/ incident report). (b) Each telephone report must...

Longitudinal review of state-level accident statistics for carriers of interstate freight

International Nuclear Information System (INIS)

Saricks, C.; Kvitek, T.

1994-03-01

State-level accident rates by mode of freight transport have been developed and refined for application to the US Department of Energy's (DOE's) environmental mitigation program, which may involve large-quantity shipments of hazardous and mixed wastes from DOE facilities. These rates reflect multi-year data for interstate-registered highway earners, American Association of Railroads member carriers, and coastal and internal waterway barge traffic. Adjustments have been made to account for the share of highway combination-truck traffic actually attributable to interstate-registered carriers and for duplicate or otherwise inaccurate entries in the public-use accident data files used. State-to-state variation in rates is discussed, as is the stability of rates over time. Computed highway rates have been verified with actual carriers of high- and low-level nuclear materials, and the most recent truck accident data have been used, to ensure that the results are of the correct order of magnitude. Study conclusions suggest that DOE use the computed rates for the three modes until (1) improved estimation techniques for highway combination-truck miles by state become available; (2) continued evolution of the railroad industry significantly increases the consolidation of interstate rail traffic onto fewer high-capacity trunk lines; or (3) a large-scale off-site waste shipment campaign is imminent

Structural safety evaluation of the K Basin railcar and truck applications

International Nuclear Information System (INIS)

Winkel, B.V.

1995-08-01

There are two rail spurs in the storage/transfer areas of both the K East and K West fuel storage basins. These rail spurs both end at the west edge of the basins. To avoid accidental entry of a railcar into a basin, administrative procedures and rail control hardware have been provided. Based upon a combination of historical documentation and existing adminstrative controls, a maximum credible impact accident was established. Using this design basis accident, the existing rail control hardware was evaluated for structural adequacy. The K Basin rail spurs are embedded in concrete, which permits truck/trailer entry into the same area. Safety issues for truck applications are also addressed

Intervention strategies to eliminate truck-related fatalities in surface coal mining in West Virginia.

Science.gov (United States)

Zhang, Meng; Kecojevic, Vladislav

2016-01-01

The main objective of this review was to build upon a previous study on the root causes of truck-related fatalities in surface coal mining operations in West Virginia, and to develop intervention strategies to eliminate these fatalities. This review considers a two-pronged approach to accident prevention: one that is fundamental and traditional (safety regulations, training and education, and engineering of the work environment); and one that is innovative and creative (e.g., applying technological advances to better control and eliminate the root causes of accidents). Suggestions for improving current training and education system are proposed, and recommendations are provided on improving the safety of mine working conditions, specifically safety conditions on haul roads, dump sites, and loading areas. We also discuss various currently available technologies that can help prevent haul truck-related fatal accidents. The results of this review should be used by mine personnel to help create safer working conditions and decrease truck-related fatalities in surface coal mining.

Study of evacuation times based on recent accident history

International Nuclear Information System (INIS)

Mills, G.S.; Neuhauser, K.S.

1995-01-01

A key parameter in the calculation of accident dose-risks by the RADTRAN 4 code is the time assigned for evacuation of the affected area surrounding the accident. Currently, in the interest of assured conservatism, this time is set at 24 hrs. Casual anecdotal evidence has indicated that this value is overly conservative and results in assignment of overly conservative estimates of accident dose-risk. Therefore, a survey of recent truck accidents involving various hazardous materials which required evacuation of surrounding populations reported in various news media was undertaken. Accounts of pertinent scenarios were gleaned from databases citing newspapers and other periodicals, and the local authorities involved in each were contacted to get details of the evacuation including time required. This paper presents the data obtained in the study and the resultant mean evacuation time plus limits and factors influencing specific results together with conclusions regarding the appropriate value to be used in the RADTRAN 4 code

Safety demonstration analyses on criticality for severe accident during overland transport of fresh nuclear fuel

International Nuclear Information System (INIS)

Takahashi, Satoshi; Okuno, Hiroshi; Yamada, Kenji; Watanabe, Kouji; Nomura, Yasushi; Miyoshi, Yoshinori

2005-01-01

Criticality safety analysis was performed for transport packages of uranium dioxide powder or of fresh PWR fuel involved in a severe accident during overland transportation, and as a result, sub-criticality was confirmed against impact accident conditions such as loaded by a drop from high position to a concrete or asphalt surface, and fire accident conditions such as caused by collisions with an oil tank trailer carrying lots of inflammable material in open air, or with a commonly used two-ton-truck inside an unventilated tunnel. (author)

Unintentional stoppages of trucks hauling high-level nuclear waste in Nevada

International Nuclear Information System (INIS)

Glickman, T.S.

1991-01-01

Any unintentional stoppage of trucks hauling high-level nuclear waste in Nevada could intensify public concerns about the negative impacts of the Yucca Mountain Project. This paper provides estimates of the expected number and frequency of such stoppages under several alternative scenarios for the routing and volume of the anticipated truck shipments. At least twice as many truck stoppages are expected to occur on freeways as on non-freeways, and at least twice as many are expected to occur in rural areas as in other areas. The expected frequency of such stoppages in the state is estimated to range from about 3 per year to one every 3 1/2 years. About one in every 4 of the stoppages is expected to take place in Las Vegas and 3 out of every 4 are expected to be non-accidents such as mechanical disablements. The minimum duration of the stoppages is expected to be on the order of half an hour for disablements and an hour for accidents

Comparisons of Traffic Collisions between Expressways and Rural Roads in Truck Drivers

Directory of Open Access Journals (Sweden)

Sangbok Lee

2016-03-01

Conclusion: This study can be used as a guideline and a base line to develop a plan of action to prevent traffic accidents. It can also help to prepare formal regulations about a truck driver's vehicle maintenance and driving attitude for a precaution on road accidents.

Factors affecting driver alertness during the operation of haul trucks in the South African mining industry

CSIR Research Space (South Africa)

Schutte, PC

2003-06-01

Full Text Available In view of the seriousness of haul trucks accidents, SIMRAC initiated research to identify factors affecting haul truck driver alertness during mining operations. The information obtained during the risk analysis was used to identify possible...

Buses involved in fatal accidents codebook 2008.

Science.gov (United States)

2011-03-01

This report provides documentation for UMTRIs file of Buses Involved in Fatal Accidents (BIFA), 2008, : including distributions of the code values for each variable in the file. The 2008 BIFA file is a census of all : buses involved in a fatal acc...

Buses involved in fatal accidents codebook 2007.

Science.gov (United States)

2009-12-01

This report provides documentation for UMTRIs file of Buses Involved in Fatal Accidents (BIFA), 2007, : including distributions of the code values for each variable in the file. The 2007 BIFA file is a census of all : buses involved in a fatal acc...

[Labor accidents involving the eyes: assessment of occupational risks involving nursing workers].

Science.gov (United States)

de Almeida, Cristiana Brasil; Pagliuca, Lorita Marlena Freitag; Leite, Ana Lourdes Almeida e Silva

2005-01-01

The study aimed at identifying nursing workers who were victims of eye accidents and the type of accident; describing the measures taken and proposing Health Education methods. A descriptive and exploratory study was carried out at a public maternity hospital from September 2002 to January 2003. Data were collected through direct observation of the environment and interviews with workers. Subjects were ten professionals (one nurse, two technicians and seven nursing auxiliaries) who were victims of work accidents involving the eye. The accidents were grouped according to the type of material that caused the trauma: chemical substances (4), medication (3), mechanical trauma (1), scalp (1) and urine (1). The results reveal that hospital workers are vulnerable to labor accidents because the environment presents biological, chemical and physical risks. An important step to prevent the occurrence of new accidents would be the prevention of human mistakes through permanent training and the use of protection glasses.

Effects of personality on risky driving behavior and accident involvement for Chinese drivers.

Science.gov (United States)

Yang, Jiaoyan; Du, Feng; Qu, Weina; Gong, Zhun; Sun, Xianghong

2013-01-01

Motor vehicle accidents are the leading cause of injury-related fatalities in China and pose the most serious threat to driving safety. Driver personality is considered as an effective predictor for risky driving behavior and accident liability. Previous studies have focused on the relationship between personality and risky driving behavior, but only a few of them have explored the effects of personality variables on accident involvement. In addition, few studies have examined the effects of personality on Chinese drivers' risky driving and accident involvement. The present study aimed to examine the effects of personality variables on Chinese drivers' unsafe driving behaviors and accident involvement. Two hundred and twenty-four Chinese drivers aged 20 to 50 were required to complete questionnaires assessing their personality traits (anger, sensation-seeking, altruism, and normlessness), risky driving behaviors (aggressive violations, ordinary violations), and accident involvement (all accidents, serious accidents, at-fault accidents). Multivariate regression analyses, adjusting for gender, age, and overall mileage, were conducted to identify the personality traits related to risky driving behaviors and accident involvement. Participants' personality traits were found to be significantly correlated with both risky driving behavior and accident involvement. Specifically, the traits of anger and normlessness were effective predictors for aggressive violations. The traits of anger, sensation-seeking, normlessness, and altruism were effective predictors for ordinary violations. Moreover, altruism and normlessness were significant predictors for the total number of accidents participants had during the past 3 years. Consistent with previous studies, the present study revealed that personality traits play an important role in predicting Chinese drivers' risky driving behaviors. In addition, Chinese drivers' personality characteristics were also associated with accident

Organizational influence on the occurrence of work accidents involving exposure to biological material.

Science.gov (United States)

Marziale, Maria Helena Palucci; Rocha, Fernanda Ludmilla Rossi; Robazzi, Maria Lúcia do Carmo Cruz; Cenzi, Camila Maria; dos Santos, Heloisa Ehmke Cardoso; Trovó, Marli Elisa Mendes

2013-01-01

to analyze work accidents involving exposure to biological materials which took place among personnel working in nursing and to evaluate the influence of the organizational culture on the occurrence of these accidents. a retrospective, analytical study, carried out in two stages in a hospital that was part of the Network for the Prevention of Work Accidents. The first stage involved the analysis of the characteristics of the work accidents involving exposure to biological materials as recorded over a seven-year period by the nursing staff in the hospital studied, and registered in the Network databank. The second stage involved the analysis of 122 nursing staff members' perception of the institutional culture, who were allocated to the control group (workers who had not had an accident) and the case group (workers who had had an accident). 386 accidents had been recorded: percutaneous lesions occurred in 79% of the cases, needles were the materials involved in 69.7% of the accidents, and in 81.9% of the accident there was contact with blood. Regarding the influence of the organizational culture on the occurrence of accidents, the results obtained through the analysis of the two groups did not demonstrate significant differences between the average scores attributed by the workers in each organizational value or practice category. It is concluded that accidents involving exposure to biological material need to be avoided, however, it was not possible to confirm the influence of organizational values or practices on workers' behavior concerning the occurrence of these accidents.

Design and Validation Testing of TruckScan to Assay Large Sacks of Fukushima Radioactive Debris on a Truck

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Atsuo [Canberra-Japan (Japan); Bronson, Frazier [Canberra Industries Inc. (United States)

2015-07-01

As a result of the March 2011 earthquake and resulting tsunami in Japan, there was a serious accident at the Fukushima Dai-ichi Nuclear Power Plant. This accident has contaminated soil and vegetation in a wide area around the plant. Decontamination projects over the last 4 years have resulted in large numbers of 1 cubic meter canvas bags of debris, commonly called Super Sacks [SS]. These are currently stored nearby where they were generated, but starting in 2015, they will be moved to various Interim Storage Facilities [ISF]. Trucks will typically carry 8-20 of these SSs. When the trucks arrive at the ISF they need to be rapidly sorted into groups according to radioactivity level, for efficient subsequent processing. Canberra Industries, Inc. [CI] has designed a new truck monitoring system 'TruckScan' for use at these ISFs. The TruckScan system must measure the entire truck loaded with multiple closely packed SSs, and generate a nuclide specific assay report showing the radioactivity in each individual SS. The Canberra-Japan office, along with Obayashi Corporation have performed validation testing to demonstrate to the regulatory authorities that the proposed technique was sufficiently accurate. These validation tests were conducted at a temporary storage area in Fukushima prefecture. Decontaminated waste of various representative types and of various levels of radioactivity was gathered and mixed to create homogeneous volumes. These volumes were sampled multiple times and assayed with laboratory HPGe detectors to determine the reference concentration of each pile. Multiple SSs were loaded from each pile. Some of the SSs were filled 50% full, others 75% full, and others 100% full, to represent the typical loading configuration of the existing SSs in the field. The content of the SSs are either sand, soil, or vegetation with densities ranging from 0.3 g/cc - 1.6 g/cc. These SSs with known concentrations of Cs-134 and Cs-137 were then loaded onto trucks in

Design and Validation Testing of TruckScan to Assay Large Sacks of Fukushima Radioactive Debris on a Truck

International Nuclear Information System (INIS)

Suzuki, Atsuo; Bronson, Frazier

2015-01-01

As a result of the March 2011 earthquake and resulting tsunami in Japan, there was a serious accident at the Fukushima Dai-ichi Nuclear Power Plant. This accident has contaminated soil and vegetation in a wide area around the plant. Decontamination projects over the last 4 years have resulted in large numbers of 1 cubic meter canvas bags of debris, commonly called Super Sacks [SS]. These are currently stored nearby where they were generated, but starting in 2015, they will be moved to various Interim Storage Facilities [ISF]. Trucks will typically carry 8-20 of these SSs. When the trucks arrive at the ISF they need to be rapidly sorted into groups according to radioactivity level, for efficient subsequent processing. Canberra Industries, Inc. [CI] has designed a new truck monitoring system 'TruckScan' for use at these ISFs. The TruckScan system must measure the entire truck loaded with multiple closely packed SSs, and generate a nuclide specific assay report showing the radioactivity in each individual SS. The Canberra-Japan office, along with Obayashi Corporation have performed validation testing to demonstrate to the regulatory authorities that the proposed technique was sufficiently accurate. These validation tests were conducted at a temporary storage area in Fukushima prefecture. Decontaminated waste of various representative types and of various levels of radioactivity was gathered and mixed to create homogeneous volumes. These volumes were sampled multiple times and assayed with laboratory HPGe detectors to determine the reference concentration of each pile. Multiple SSs were loaded from each pile. Some of the SSs were filled 50% full, others 75% full, and others 100% full, to represent the typical loading configuration of the existing SSs in the field. The content of the SSs are either sand, soil, or vegetation with densities ranging from 0.3 g/cc - 1.6 g/cc. These SSs with known concentrations of Cs-134 and Cs-137 were then loaded onto trucks in

Transportation accidents/incidents involving radioactive materials (1971--1991)

International Nuclear Information System (INIS)

Cashwell, C.E.; McClure, J.D.

1992-01-01

The Radioactive Materials Incident Report (RMIR) database contains information on transportation-related accidents and incidents involving radioactive materials that have occurred in the United States. The RMIR was developed at Sandia National Laboratories (SNL) to support its research and development program efforts for the US Department of Energy (DOE). This paper will address the following topics: background information on the regulations and process for reporting a hazardous materials transportation incident, overview data of radioactive materials transportation accidents and incidents, and additional information and summary data on how packagings have performed in accident conditions

Inventory of accidents and losses at sea involving radioactive material

International Nuclear Information System (INIS)

2001-09-01

The present report describes the content of the inventory of accidents and losses at sea involving radioactive material. It covers accidents and losses resulting in the actual release of radioactive materials into the marine environment and also those which have the potential for release. For completeness, records of radioactive materials involved in accidents but which were recovered intact from the sea are also reported. Information on losses of sealed sources resulting in actual or potential release of activity to the marine environment nad of sealed sources that were recovered intact is also presented

Dump truck-related deaths in construction, 1992-2007.

Science.gov (United States)

McCann, Michael; Cheng, Mei-Tai

2012-05-01

Dump trucks are universally used in construction and other industries to haul materials to the location and to remove waste materials. The source for dump truck-related fatality data was the Bureau of Labor Statistics Census of Fatal Occupational Injuries (CFOI) Research File. From 1992 to 2007, 829 construction workers were killed in dump truck-related incidents nationwide. Of those, 336 were dump truck operators with 215 deaths occurring in street and highway incidents. Another 343 deaths involved workers on foot, three-quarters struck by dump trucks. Sixty-four of the construction workers killed were maintaining dump trucks, 22 when caught between the truck frame and a falling dump truck bed. Of the 86 other deaths, 55 involved streets and highways. Recommendations include: (i) improving the reporting of seat belt usage in fatality reports; (ii) requiring use of seat belts; (iii) requiring the use of backup alarms, spotters, or other methods to alert dump truck operators to workers in their blind spots; (iv) prohibiting direct dumping at river banks and embankments; (v) using cameras or radar to enforce stopping at railway crossings; and (xi) enforcing worker safety practices (e.g., lockout/tagout procedures on elevated dump truck beds). Copyright © 2011 Wiley Periodicals, Inc.

Accidents involving specialized aircraft in agriculture aerial spraying

Directory of Open Access Journals (Sweden)

Marcelo Boamorte Ravelli

Full Text Available ABSTRACT: The great challenge for the practice of agricultural aviation has been to avoid accidents. Although, there are technological progress and high resources for safety, accidents continue to occur. The objective of this research was to analyze the influence and occurrence of factors in agricultural aviation accidents in Brazil recently. Based on research and technical - scientific papers written by researchers and aviation authorities, recommendations directed towards reducing the risks associated with this aircraft modality are assessed. The main factors responsible for accidents are normally operational errors and maneuvers that cause flight collisions, engine failures and altitude loss. Professional awareness and qualification converge towards the success of the agricultural pilot in the detection of inherent dangers or occasional in the various systems involved.

Heavy truck rollover characterization (phase B).

Science.gov (United States)

2009-09-01

The Heavy Truck Rollover Characterization Study - Phase-B builds on the results of prior phases of research. Phases 1 and 2 (Funded by Federal Highway Administration) involved heavy truck rollover characterization for a tractor and box-trailer; and P...

Traffic Accidents Involving Cyclists Identifying Causal Factors Using Questionnaire Survey, Traffic Accident Data, and Real-World Observation.

Science.gov (United States)

Oikawa, Shoko; Hirose, Toshiya; Aomura, Shigeru; Matsui, Yasuhiro

2016-11-01

The purpose of this study is to clarify the mechanism of traffic accidents involving cyclists. The focus is on the characteristics of cyclist accidents and scenarios, because the number of traffic accidents involving cyclists in Tokyo is the highest in Japan. First, dangerous situations in traffic incidents were investigated by collecting data from 304 cyclists in one city in Tokyo using a questionnaire survey. The survey indicated that cyclists used their bicycles generally while commuting to work or school in the morning. Second, the study investigated the characteristics of 250 accident situations involving cyclists that happened in the city using real-world bicycle accident data. The results revealed that the traffic accidents occurred at intersections of local streets, where cyclists collided most often with vehicles during commute time in the morning. Third, cyclists' behavior was observed at a local street intersection in the morning in the city using video pictures. In one hour during the morning commute period, 250 bicycles passed through the intersection. The results indicated that one of the reasons for traffic accidents involving cyclists might be the combined effect of low visibility, caused by the presence of box-like building structures close to the intersections, and the cyclists' behavior in terms of their velocity and no confirming safety. It was observed that, on average, bicycle velocity was 3.1 m/s at the initial line of an intersection. The findings from this study could be useful in developing new technologies to improve cyclist safety, such as alert devices for cyclists and vehicle drivers, wireless communication systems between cyclists and vehicle drivers, or advanced vehicles with bicycle detection and collision mitigation systems.

Association between commercial vehicle driver at-fault crashes involving sleepiness/fatigue and proximity to rest areas and truck stops.

Science.gov (United States)

Bunn, Terry L; Slavova, Svetla; Rock, Peter J

2017-11-22

There is ongoing concern at the national level about the availability of adequate commercial vehicle rest areas and truck stops for commercial vehicle drivers to rest or to wait for a delivery window. A retrospective case-control study was conducted to determine the association between the occurrence of sleepiness/fatigue-related (cases) vs. all other human factor-related commercial vehicle driver at-fault crashes (controls) and proximity to rest areas, weigh stations with rest havens, and truck stops. Commercial vehicle driver at-fault crashes involving sleepiness/fatigue were more likely to occur on roadways where the nearest rest areas/weigh stations with rest havens/truck stops were located 20 miles or more from the commercial vehicle crash site (Odds Ratio [OR]=2.32; Confidence Interval [CI] 1.615, 3.335] for 20-39.9 miles vs. commercial vehicle at-fault driver crashes with human factors other than sleepiness/fatigue cited in crash reports. Commercial vehicle driver at-fault crashes involving sleepiness/fatigue also were more likely to occur on parkways compared to interstates (adjusted OR=3.747 [CI 2.83, 4.95]), during nighttime hours (adjusted OR=6.199 [CI 4.733, 8.119]), and on dry pavement (adjusted OR 1.909, [CI 1.373, 2.655]). The use of statewide crash data analysis coupled with ArcGIS mapping capabilities provided the opportunity to both statistically determine and to visualize the association between rest area/weigh station with rest haven/truck stop distance and the occurrence of commercial vehicle driver at-fault crashes involving sleepiness/fatigue. Implementation and evaluation of commercial vehicle employer policies and interventions such as the use of commercial vehicle driver fatigue alert systems may help to reduce fatigue and sleepiness in commercial vehicle drivers. These results can be used by state and local highway transportation officials to inform and increase truck parking availability, especially on parkways. Copyright © 2017

Characteristics of motorcyclists involved in accidents between motorcycles and automobiles.

Science.gov (United States)

Oliveira, Amanda Lima de; Petroianu, Andy; Gonçalves, Dafne Maria Villar; Pereira, Gisele Araújo; Alberti, Luiz Ronaldo

2015-01-01

traffic accidents are one of the main causes of death and disability, with motorcyclists representing the great majority of both the victims and the perpetrators. this work studied the characteristics of motorcyclists injured in accidents involving motorcycles and automobiles. this study sought to interview 100 motorcyclists who had been injured in collisions between motorcycles and automobiles, and who were undergoing emergency hospital treatment in the region of Belo Horizonte, Brazil. The questionnaires included demographic information (age, gender, skin color, education level, profession) and questions about years of licensed driving practice, how often they would drive an automobile, how long they had had a motorcycle driver's license, how often they would ride a motorcycle, the number of prior accidents involving a car, and the number of prior accidents not involving a car. of the 100 consecutive accidents studied, 91 occurred with men and 9 with women, aged between 16 and 79 (m = 29 ± 11) years. Regarding their reason for using a motorcycle, 83% reported using it for transport, 7% for work, and 10% for leisure. Most of these accident victims had secondary or higher education (47%). Of the motorcyclists who held a car driver's license, 68.3% drove the vehicle daily or weekly and held the license for more than one year. Sixty-seven percent of the accident victims used a motorcycle daily and had a motorcycle driver's license for at least one year. among the motorcyclists injured, most were men aged 20 years or older, with complete secondary education, and experienced in driving both motorcycles and cars, indicating that recklessness while driving the motorcycle is the main cause of traffic accidents.

Estimated consequences from severe spent nuclear fuel transportation accidents

International Nuclear Information System (INIS)

Arnish, J.J.; Monette, F.; LePoire, D.; Biwer, B.M.

1996-01-01

The RISKIND software package is used to estimate radiological consequences of severe accident scenarios involving the transportation of spent nuclear fuel. Radiological risks are estimated for both a collective population and a maximally exposed individual based on representative truck and rail cask designs described in the U.S. Nuclear Regulatory Commission (NRC) modal study. The estimate of collective population risk considers all possible environmental pathways, including acute and long-term exposures, and is presented in terms of the 50-y committed effective dose equivalent. Radiological risks to a maximally exposed individual from acute exposure are estimated and presented in terms of the first year and 50-y committed effective dose equivalent. Consequences are estimated for accidents occurring in rural and urban population areas. The modeled pathways include inhalation during initial passing of the radioactive cloud, external exposure from a reduction of the cask shielding, long-term external exposure. from ground deposition, and ingestion from contaminated food (rural only). The major pathways and contributing radionuclides are identified, and the effects of possible mitigative actions are discussed. The cask accident responses and the radionuclide release fractions are modeled as described in the NRC modal study. Estimates of severe accident probabilities are presented for both truck and rail modes of transport. The assumptions made in this study tend to be conservative; however, a set of multiplicative factors are identified that can be applied to estimate more realistic conditions

Characteristics of motorcyclists involved in accidents between motorcycles and automobiles

Directory of Open Access Journals (Sweden)

Amanda Lima de Oliveira

2015-02-01

Full Text Available Introduction: traffic accidents are one of the main causes of death and disability, with motorcyclists representing the great majority of both the victims and the perpetrators. Objective: this work studied the characteristics of motorcyclists injured in accidents involving motorcycles and automobiles. Method: this study sought to interview 100 motorcyclists who had been injured in collisions between motorcycles and automobiles, and who were undergoing emergency hospital treatment in the region of Belo Horizonte, Brazil. The questionnaires included demographic information (age, gender, skin color, education level, profession and questions about years of licensed driving practice, how often they would drive an automobile, how long they had had a motorcycle driver’s license, how often they would ride a motorcycle, the number of prior accidents involving a car, and the number of prior accidents not involving a car. Results: of the 100 consecutive accidents studied, 91 occurred with men and 9 with women, aged between 16 and 79 (m = 29 ± 11 years. Regarding their reason for using a motorcycle, 83% reported using it for transport, 7% for work, and 10% for leisure. Most of these accident victims had secondary or higher education (47%. Of the motorcyclists who held a car driver’s license, 68.3% drove the vehicle daily or weekly and held the license for more than one year. Sixty-seven percent of the accident victims used a motorcycle daily and had a motorcycle driver’s license for at least one year. Conclusion: among the motorcyclists injured, most were men aged 20 years or older, with complete secondary education, and experienced in driving both motorcycles and cars, indicating that recklessness while driving the motorcycle is the main cause of traffic accidents.

Shipping container response to severe highway and railway accident conditions: Appendices

International Nuclear Information System (INIS)

Fischer, L.E.; Chou, C.K.; Gerhard, M.A.; Kimura, C.Y.; Martin, R.W.; Mensing, R.W.; Mount, M.E.; Witte, M.C.

1987-02-01

Volume 2 contains the following appendices: Severe accident data; truck accident data; railroad accident data; highway survey data and bridge column properties; structural analysis; thermal analysis; probability estimation techniques; and benchmarking for computer codes used in impact analysis. (LN)

Pregnancy outcome in women involved in road traffic accidents

African Journals Online (AJOL)

bbshehu

December, 2002, was undertaken to determine the incidence, type of injury and pregnancy outcome. Results: One hundred and forty nine women ... road traffic accidents.6 Pregnant mothers could also be involved in road traffic accident.6 ... use of helmet lowers the risk of traumatic brain injury. 11 and a case is made for the ...

Manual on the medical management of individuals involved in radiation accidents

International Nuclear Information System (INIS)

Swindon, T.N.

1991-09-01

This manual is concerned with accidents or emergencies which involve sources of ionizing radiation. It does not cover other forms of radiation such as non-ionizing radiation (ultra-violet, light, radiofrequency radiations), heat, etc. Most radiation accidents have involved individuals either at the workplace or with medical misadministrations; they have received external exposure from X-ray or gamma-ray sources or have been contaminated with radioactive material. A few members of the public have also been involved through misadventures with radioactive sources although these may not be thought of as accidents; more commonly, they are referred to as 'incidents'. For the purpose of this manual, there is not differentiation between an accident and an incident, as the medical care required is the same in both situations. Some of the reference papers are reprinted at the back of the manual. 17 refs., 12 tabs., 9 figs

Alcohol abuse and involvement in traffic accidents in the Brazilian population, 2013.

Science.gov (United States)

Damacena, Giseli Nogueira; Malta, Deborah Carvalho; Boccolini, Cristiano Siqueira; Souza, Paulo Roberto Borges de; Almeida, Wanessa da Silva de; Ribeiro, Lucas Sisinno; Szwarcwald, Célia Landmann

2016-12-01

Abstract This article aims to analyze alcohol abuse and frequent consumption according to sociodemographic characteristics and investigate the risk of greater involvement in traffic accidents, using data from the National Health Survey (PNS), 2013, Brazil. Events investigated were alcohol abuse and frequent consumption and if the individual was involved in a traffic accident and sustained an injury in the last 12 months. We investigated both events according to sociodemographic characteristics and assessed the association among them through multivariate logistic regression. The prevalence of alcohol abuse and frequent consumption was 6.1% for the population aged 18 years and over, 8.9% among men and 3.6% among women. The prevalence of involvement in traffic accidents was 3.1% in the general population and 6.1% among those who reported alcohol abuse. After controlling for sociodemographic factors, alcohol abuse and frequent consumption was significantly associated with traffic accidents. Considering a higher risk of involvement in traffic accidents among individuals who reported alcohol abuse and frequent consumption, monitoring blood alcohol concentration of drivers becomes a strategic possibility of intervention.

Implementation of exclusive truck facilities

Energy Technology Data Exchange (ETDEWEB)

Fekpe, E. [Battelle Memorial Inst., Columbus, OH (United States). Transportation Market Sector

2007-07-01

This paper discussed the issue of highway congestion, safety, and efficiency in freight movement on highways, with particular reference to the challenge of supporting increasing capacity demand from truck traffic. Innovative and practical solutions are needed to address the growing need for more efficient freight movement while maintaining acceptable levels of safety on highways. The concept of exclusive truck facilities (ETFs) is becoming an attractive option as a feasible strategy to help stabilize traffic flow, reduce congestion, improve safety, enhance transportation system management, improve access to freight facilities, and improve efficiency in freight movement along corridors of national importance. ETFs can either be truck only lanes or truckways. Passenger cars may not use ETFs. However, the use of ETFs could involve high costs of construction, maintenance, and acquisition of additional right of way. A cost-benefit analysis was performed for alternative ETF configurations under different traffic and site characteristics. A set of criteria was then proposed for identifying suitable locations for exclusive truck lanes. It was proposed that ETFs are economically feasible at locations with traffic volume of 100,000 vehicles per day or more and with a truck volume of at least 25 per cent of the traffic. In addition, the rate of truck-involved fatal crashes and level of service should be used to prioritize preliminary candidate locations that satisfy the traffic criteria. Consideration should also be given to the existence of freight terminals, ports, processing centers or regional distribution centres that are close to highways. 11 refs., 1 tab.

Large truck and bus crash facts, 2010.

Science.gov (United States)

2012-09-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2010. Selected crash statistics on passenger : vehicles are also presen...

Large truck and bus crash facts, 2012.

Science.gov (United States)

2014-06-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2012. Selected crash statistics on passenger vehicles are also presented ...

Large truck and bus crash facts, 2013.

Science.gov (United States)

2015-04-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2013. Selected crash statistics on passenger vehicles are also presented ...

Large truck and bus crash facts, 2009.

Science.gov (United States)

2011-10-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2009. Selected crash statistics on passenger : vehicles are also presen...

Large truck and bus crash facts, 2011.

Science.gov (United States)

2013-10-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2011. Selected crash statistics on passenger : vehicles are also presen...

Examining accident reports involving autonomous vehicles in California.

Directory of Open Access Journals (Sweden)

Francesca M Favarò

Full Text Available Autonomous Vehicle technology is quickly expanding its market and has found in Silicon Valley, California, a strong foothold for preliminary testing on public roads. In an effort to promote safety and transparency to consumers, the California Department of Motor Vehicles has mandated that reports of accidents involving autonomous vehicles be drafted and made available to the public. The present work shows an in-depth analysis of the accident reports filed by different manufacturers that are testing autonomous vehicles in California (testing data from September 2014 to March 2017. The data provides important information on autonomous vehicles accidents' dynamics, related to the most frequent types of collisions and impacts, accident frequencies, and other contributing factors. The study also explores important implications related to future testing and validation of semi-autonomous vehicles, tracing the investigation back to current literature as well as to the current regulatory panorama.

Examining accident reports involving autonomous vehicles in California.

Science.gov (United States)

Favarò, Francesca M; Nader, Nazanin; Eurich, Sky O; Tripp, Michelle; Varadaraju, Naresh

2017-01-01

Autonomous Vehicle technology is quickly expanding its market and has found in Silicon Valley, California, a strong foothold for preliminary testing on public roads. In an effort to promote safety and transparency to consumers, the California Department of Motor Vehicles has mandated that reports of accidents involving autonomous vehicles be drafted and made available to the public. The present work shows an in-depth analysis of the accident reports filed by different manufacturers that are testing autonomous vehicles in California (testing data from September 2014 to March 2017). The data provides important information on autonomous vehicles accidents' dynamics, related to the most frequent types of collisions and impacts, accident frequencies, and other contributing factors. The study also explores important implications related to future testing and validation of semi-autonomous vehicles, tracing the investigation back to current literature as well as to the current regulatory panorama.

Spent fuel transportation accident: a state's involvement

International Nuclear Information System (INIS)

Neuweg, M.

1978-01-01

On February 9, 1978 at 8:20 p.m., the duty officer for the Illinois Radiological Assistance Team was notified that a shipment containing uranium and plutonium was involved in an accident near Gibson City, Illinois on Route 54. It was reported that a pig containing an unknown amount of uranium and plutonium was involved. The Illinois District 6A State Police were called to the scene and secured the area. The duty officer in the meantime learned after numerous telephone calls, approximately 1 hour after the first notice was received, that the pig actually was a 48,000 pound cask containing 6 spent fuel rods and the tractor-trailer had split apart and was blocking one lane of the highway. The shipment had departed from Dresden Nuclear Power Station, Morris, Illinois, enroute to Babcox and Wilcox in Lynchburg, Virginia. Initial reports indicated the vehicle had split apart. Actually, the semi-trailer bed had buckled beneath the cask due to apparent excess stress. The cask remained entirely intact and was not damaged, but the state highway was closed to traffic. The State Radiological Assistance Team was dispatched and arrived on the scene at 12:45 a.m. Immediate radiation monitoring revealed a reading of 4 milliroentgen per hour at 10 feet from the cask. No contamination existed nor was anyone exposed to radiation unnecessarily. The cask was transferred to a Tri-State semi-trailer vehicle the following morning at approximately 6:30 a.m. At 9:30 a.m., February 10, the new vehicle was again enroute to its destination. This incident demonstrated typical occurrences involving transportation radiation accident: misinformation and/or lack of information on the initial response notification, inaccuracies of radiation monitorings at the scene of the accident, inconsistencies concerning the occurrences of the accident and unfamiliar terminology utilized by personnel first on the scene, i.e., pig, cask, vehicle split apart, etc

Routine methods for post-transportation accident recovery of spent fuel casks

International Nuclear Information System (INIS)

Shappert, L.B.; Pope, R.B.; Best, R.E.; Jones, R.H.

1991-01-01

Spent fuel casks and other large radioactive material packages have been examined to determine whether the designs are adequate to allow the casks to be recovered using conventional recovery methods following a transportation accident. Casks and similar packages are typically designed with, and handled by, trunnions that support the package during transport. These trunnions are considered the best cask feature with which to grapple the cask once it is no longer in its usual shipping mode. Following a transport accident, the trunnions may be buried or entangled so that they are not readily accessible to initiate the recovery process. To evaluate the effectiveness of applying traditional recovery methods to spent fuel casks, a workshop was held in which a series of accidents involving casks were postulated; the modes of transportation considered included truck, rail, and barge. These participants knowledgeable in transport, handling, and, in some cases, recovery of large, heavy containers attended. Participants concluded that the physical recovery of a cask involved in an accident, irrespective of where the accident occurs, would be a straightforward rigging operation and that the addition of specific recovery features (e.g., additional trunnions) to the cask appears unnecessary

Accidents involving off-road motor vehicles in a northern community.

Science.gov (United States)

Hasselback, P; Wilding, H R

1987-01-01

The increasing number of accidents associated with off-road motor vehicles used for recreational purposes prompted this prospective study. During 1985 the records of victims of all motor vehicle accidents who were seen at the Hudson Bay Union Hospital, Hudson Bay, Sask., were studied; patients involved in on-road vehicle accidents were included for comparison. Emphasis was placed on age, vehicle type, mechanism of accident, injury severity and the use of safety features. Almost half of the victims of off-road vehicle accidents were under 16 years of age. The poor adherence to government legislation and manufacturer recommendations was evident in the number of people who did not wear helmets or use headlights. PMID:3651929

Emotional reactivity: Beware its involvement in traffic accidents.

Science.gov (United States)

M'bailara, Katia; Atzeni, Thierry; Contrand, Benjamin; Derguy, Cyrielle; Bouvard, Manuel-Pierre; Lagarde, Emmanuel; Galéra, Cédric

2018-04-01

Reducing risk attributable to traffic accidents is a public health challenge. Research into risk factors in the area is now moving towards identification of the psychological factors involved, particularly emotional states. The aim of this study was to evaluate the link between emotional reactivity and responsibility in road traffic accidents. We hypothesized that the more one's emotional reactivity is disturbed, the greater the likelihood of being responsible for a traffic accident. This case-control study was based on a sample of 955 drivers injured in a motor vehicle crash. Responsibility levels were determined with a standardized method adapted from the quantitative Robertson and Drummer crash responsibility instrument. Emotional reactivity was assessed with the MATHYS. Hierarchical cluster analysis discriminated four distinctive driver's emotional reactivity profiles: basic emotional reactivity (54%), mild emotional hyper-reactivity (29%), emotional hyper-reactivity (11%) and emotional hypo-reactivity (6%). Drivers who demonstrated emotional hypo-reactivity had a 2.3-fold greater risk of being responsible for a traffic accident than those with basic emotional reactivity. Drivers' responsibility in traffic accidents depends on their emotional status. The latter can change the ability of drivers, modifying their behavior and thus increasing their propensity to exhibit risk behavior and to cause traffic accidents. Copyright © 2017 Elsevier B.V. All rights reserved.

Simulation Study of the Effect of Decreasing Truck Traffic Flow on Safety on Almeria-Barcelona Corridor

Energy Technology Data Exchange (ETDEWEB)

Dadashova, B.

2016-07-01

In this paper the effect of truck traffic on road safety has been analyzed through simulation study. The main objective of the study is to quantify the effect of the decreasing average annual daily traffic of heavy duty vehicles (trucks) on road safety. As the road safety indicators the frequency road accidents is considered. The data used in the study were collected from one of the most crowded routes in Spain which connects Almeria (south-east) with Barcelona (northeast). The observed data covers year 2010 and were classified into 2 road types: dual carriageways and toll roads. The estimation was carried out using negative binomial model and Markov Chain Monte Carlo simulation. Using the estimation results new traffic scenarios were proposed where the traffic flow is assumed to change its values. A total of 33 scenarios were proposed and new accidents data were generated through MCMC sampling. The comparison of the simulated and observed accident data shows that the effect of decreasing truck traffic flow could meliorate road safety in the route. The simulation tool could be applied to evaluate the effects of freight modal shift from road to rail. (Author)

Large truck and bus crash facts, 2008. 

Science.gov (United States)

2010-03-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2008. Selected crash statistics on passenger : vehicles are also presen...

Managing truck arrivals with time windows to alleviate gate congestion at container terminals

DEFF Research Database (Denmark)

Chen, G.; Govindan, Kannan; Yang, Z.

2013-01-01

Long truck queues at gates often limit the efficiency of a container terminal and generate serious air pollution. To reduce the gate congestion, this paper proposes a method called'vessel dependent time windows (VDTWs)' to control truck arrivals, which involves partitioning truck entries into gro......Long truck queues at gates often limit the efficiency of a container terminal and generate serious air pollution. To reduce the gate congestion, this paper proposes a method called'vessel dependent time windows (VDTWs)' to control truck arrivals, which involves partitioning truck entries...... into groups and assigning different time windows to the groups. The proposed VDTWs method includes three steps: (1) predicting truck arrivals based on the time window assignment, (2) estimating the queue length of trucks, and (3) optimizing the arrangement of time windows to minimize the total cost...

49 CFR 399.207 - Truck and truck-tractor access requirements.

Science.gov (United States)

2010-10-01

.... Exception. If air and electrical connections necessary to couple or uncouple a truck-tractor from a trailer... 49 Transportation 5 2010-10-01 2010-10-01 false Truck and truck-tractor access requirements. 399... Vehicles § 399.207 Truck and truck-tractor access requirements. (a) General rule. Any person entering or...

Psychoactive substance use by truck drivers: a systematic review.

Science.gov (United States)

Girotto, Edmarlon; Mesas, Arthur Eumann; de Andrade, Selma Maffei; Birolim, Marcela Maria

2014-01-01

The aim of this study was to summarise the scientific evidence on the prevalence of psychoactive substance use and on the factors associated with their intake among truck drivers. A systematic review was performed in the databases PubMed, Scientific Electronic Library Online, Latin American and Caribbean Health Sciences, and Cochrane and 36 cross-sectional studies were identified with quantitative results about the use of psychoactive substances by truck drivers. Out of these, 28 were carried out in countries with large land areas and 23 obtained their information through self-reporting. The most frequently studied substances were alcohol (n=25), amphetamines (n=17), marijuana (n=16) and cocaine (n=13). The prevalence of the use of these substances greatly varied: alcohol (0.1-91.0%); amphetamines (0.2-82.5%), marijuana (0.2-29.9%), cocaine (0.1-8.3%). The frequency of substance use was lower in studies that investigated the presence of these substances in biological samples than in those based on self-reported use. In 12 studies that evaluated factors associated with the intake of psychoactive substances, the following stood out: younger age, higher income, longer trips, alcohol consumption, driving in the night shift, travelling interstate routes, long or short sleep, fewer hours of rest, little experience of the driver, connection with small and medium sized companies, income below levels determined by labour agreements, productivity-based earnings and prior involvement in accidents. The frequency of psychoactive substance use by truck drivers seems to be high, although that greatly varies according to the type of substance and the method of collecting the information. The use of these substances was mainly associated with indicators of poor working conditions.

Examining accident reports involving autonomous vehicles in California

Science.gov (United States)

Nader, Nazanin; Eurich, Sky O.; Tripp, Michelle; Varadaraju, Naresh

2017-01-01

Autonomous Vehicle technology is quickly expanding its market and has found in Silicon Valley, California, a strong foothold for preliminary testing on public roads. In an effort to promote safety and transparency to consumers, the California Department of Motor Vehicles has mandated that reports of accidents involving autonomous vehicles be drafted and made available to the public. The present work shows an in-depth analysis of the accident reports filed by different manufacturers that are testing autonomous vehicles in California (testing data from September 2014 to March 2017). The data provides important information on autonomous vehicles accidents’ dynamics, related to the most frequent types of collisions and impacts, accident frequencies, and other contributing factors. The study also explores important implications related to future testing and validation of semi-autonomous vehicles, tracing the investigation back to current literature as well as to the current regulatory panorama. PMID:28931022

MCDA APPLIED TO PERFORMANCE APPRAISAL OF SHORT-HAUL TRUCK DRIVERS: A CASE STUDY IN A PORTUGUESE TRUCKING COMPANY

Directory of Open Access Journals (Sweden)

Raquel Morte

2015-03-01

Full Text Available Performance appraisal increasingly assumes a more important role in any organizational environment. In the trucking industry, drivers are the company's image and for this reason it is important to develop and increase their performance and commitment to the company's goals. This paper aims to create a performance appraisal model for trucking drivers, based on a multi-criteria decision aid methodology. The PROMETHEE and MMASSI methodologies were adapted using the criteria used for performance appraisal by the trucking company studied. The appraisal involved all the truck drivers, their supervisors and the company's Managing Director. The final output is a ranking of the drivers, based on their performance, for each one of the scenarios used. The results are to be used as a decision-making tool to allocate drivers to the domestic haul service.

Anatomy of Sodium Hypochlorite Accidents Involving Facial Ecchymosis – A Review

Science.gov (United States)

Zhu, Wan-chun; Gyamfi, Jacqueline; Niu, Li-na; Schoeffel, G. John; Liu, Si-ying; Santarcangelo, Filippo; Khan, Sara; Tay, Kelvin C-Y.; Pashley, David H.; Tay, Franklin R.

2013-01-01

Objectives Root canal treatment forms an essential part of general dental practice. Sodium hypochlorite (NaOCl) is the most commonly used irrigant in endodontics due to its ability to dissolve organic soft tissues in the root canal system and its action as a potent antimicrobial agent. Although NaOCl accidents created by extrusion of the irrigant through root apices are relatively rare and are seldom life-threatening, they do create substantial morbidity when they occur. Methods To date, NaOCl accidents have only been published as isolated case reports. Although previous studies have attempted to summarise the symptoms involved in these case reports, there was no endeavor to analyse the distribution of soft tissue distribution in those reports. In this review, the anatomy of a classical NaOCl accident that involves facial swelling and ecchymosis is discussed. Results By summarising the facial manifestations presented in previous case reports, a novel hypothesis that involves intravenous infusion of extruded NaOCl into the facial vein via non-collapsible venous sinusoids within the cancellous bone is presented. Conclusions Understanding the mechanism involved in precipitating a classic NaOCl accident will enable the profession to make the best decision regarding the choice of irrigant delivery techniques in root canal débridement, and for manufacturers to design and improve their irrigation systems to achieve maximum safety and efficient cleanliness of the root canal system. PMID:23994710

Can cars and trucks coexist peacefully on highways? Analyzing the effectiveness of road safety policies in Europe.

Science.gov (United States)

Castillo-Manzano, José I; Castro-Nuño, Mercedes; Fageda, Xavier

2015-04-01

We examine the impact on the traffic accident rate of the interaction between trucks and cars on Europe's roads using a panel data set that covers the period 1999-2010. We find that rising motorization rates for trucks lead to higher traffic fatalities, while rising motorization rates for cars do not. Empirically, the model we build predicts the positive impact of stricter speed limit legislation for trucks in the reduction of road fatalities. These findings lend support to European strategies and aimed at promoting alternative modes of freight transport, including rail and maritime transport. Copyright © 2015 Elsevier Ltd. All rights reserved.

A tough truck for ATLAS

CERN Multimedia

2003-01-01

One of the mobile support structures that will be used to manoeuvre and assemble components of the ATLAS detector in its cavern was put through its paces at the end of July and passed its load tests with flying colours. The tests, which involved the surveyors taking measurements to detect any load-induced mechanical deformations, were carried out in Building 191. "The "truck" has been subjected to static tests with loads of up to 1250 tonnes and can carry and transport on air cushions a nominal load of up to 1000 tonnes at a top speed of 30 cm per minute," explains project leader Tommi Nyman. "It took two weeks to assemble the truck's components, the last of which arrived at CERN on 24 June. It then took a further 20 days to load the truck up for the test." The 8.5 metre-high truck will be used for final assembly of some of the ATLAS components, including the calorimeters, in cavern UX15. This powerful device is the result of a collaboration between CERN and the Henryk Niewodniczanski Institute of Nuclear ...

Experimental study on transportation safety of package in side collision of heavy duty truck

International Nuclear Information System (INIS)

Suga, M.; Sasaki, T.

1989-01-01

The accidents in road transportation of package may be collision, fall and fire. It is necessary to examine all cases very carefully because collision might be caused by other vehicle. Collisions are classified into head-on collision, rear-end collision, side collision. A lot of experiments and analyses are reported on head-on collision, so the behavior of vehicle and package may be predicted without difficulty. Rear-end collisions bring about less impact and may be applied corresponding to the head-on collisions. About side collisions, few experiments or analyses are reported, and most of them are about passenger cars not about trucks. So it becomes important to study the transportation safety of package carried on a heavy duty truck when hit on the side by another truck similar in size

Emergency response planning and preparedness for transport accidents involving radioactive material

International Nuclear Information System (INIS)

1988-01-01

The purpose of this Guide is to provide assistance to public authorities and others (including consignors and carriers of radioactive materials) who are responsible for ensuring safety in establishing and developing emergency response arrangements for responding effectively to transport accidents involving radioactive materials. This Guide is concerned mainly with the preparation of emergency response plans. It provides information which will assist those countries whose involvement with radioactive materials is just beginning and those which have already developed their industries involving radioactive materials and attendant emergency plans, but may need to review and improve these plans. The need for emergency response plans and the ways in which they are implemented vary from country to country. In each country, the responsible authorities must decide how best to apply this Guide, taking into account the actual shipments and associated hazards. In this Guide the emergency response planning and response philosophy are outlined, including identification of emergency response organizations and emergency services that would be required during a transport accident. General consequences which could prevail during an accident are described taking into account the IAEA Regulations for the Safe Transport of Radioactive Material. 43 refs, figs and tabs

[A spatially explicit analysis of traffic accidents involving pedestrians and cyclists in Berlin].

Science.gov (United States)

Lakes, Tobia

2017-12-01

In many German cities and counties, sustainable mobility concepts that strengthen pedestrian and cyclist traffic are promoted. From the perspectives of urban development, traffic planning and public healthcare, a spatially differentiated analysis of traffic accident data is decisive. 1) The identification of spatial and temporal patterns of the distribution of accidents involving cyclists and pedestrians, 2) the identification of hotspots and exploration of possible underlying causes and 3) the critical discussion of benefits and challenges of the results and the derivation of conclusions. Spatio-temporal distributions of data from accident statistics in Berlin involving pedestrians and cyclists from 2011 to 2015 were analysed with geographic information systems (GIS). While the total number of accidents remains relatively stable for pedestrian and cyclist accidents, the spatial distribution analysis shows, however, that there are significant spatial clusters (hotspots) of traffic accidents with a strong concentration in the inner city area. In a critical discussion, the benefits of geographic concepts are identified, such as spatially explicit health data (in this case traffic accident data), the importance of the integration of other data sources for the evaluation of the health impact of areas (traffic accident statistics of the police), and the possibilities and limitations of spatial-temporal data analysis (spatial point-density analyses) for the derivation of decision-supported recommendations and for the evaluation of policy measures of health prevention and of health-relevant urban development.

Mothers' knowledge of domestic accident prevention involving children in Baghdad City.

Science.gov (United States)

Lafta, Riyadh K; Al-Shatari, Sahar A; Abass, Seba

2013-01-01

Accidental injuries are the most common cause of death in children over the age of one. Every year, millions of children are permanently disabled or disfigured because of accidents. To assess the level of knowledge of women with respect to children's domestic accidents, and to determine its association with some demographic factors. This cross-sectional study was conducted in both sides of Baghdad City during the period from April through to August 2013. The targeted population were women attending the primary health care centers (PHCCs). A random sample of 20 PHCCs was taken through a stratified random sampling technique by dividing Baghdad City into its two main parts Karkh and Russafa. Ten centers were then chosen from each sector by a simple random sampling technique. A well-structured questionnaire was developed that constituted of questions on four main types of accidents involving children (poisoning by chemicals and detergents, electric shock, injuries from sharp instruments in the kitchen, and burns). The total number of women enrolled in this study was 1032 aged from 15-50 years. The results revealed that only 9.2% of the mothers acquired a good level of knowledge in prevention of injuries from chemicals and detergents, and more than 90% were found to have poor knowledge. The same was found regarding knowledge about preventing electrical accidents caused by power sockets and electrical appliances where only 10.2% of the mothers were found to have a good level of knowledge. The results were not much better regarding accidents caused by fire, only 11.6% of the mothers scored well. With respect to dealing with accidents caused by sharp instruments in the kitchen, only 6.3% of the mothers obtained a score that indicated a good level of knowledge. Older mothers were statistically found to have a better level of knowledge than younger mothers. Higher educated mothers' were statistically associated with a lower level of knowledge in accident prevention. Mothers

Planning and Preparing for Emergency Response to Transport Accidents Involving Radioactive Material. Safety Guide

International Nuclear Information System (INIS)

2009-01-01

This Safety Guide provides guidance on various aspects of emergency planning and preparedness for dealing effectively and safely with transport accidents involving radioactive material, including the assignment of responsibilities. It reflects the requirements specified in Safety Standards Series No. TS-R-1, Regulations for the Safe Transport of Radioactive Material, and those of Safety Series No. 115, International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources. Contents: 1. Introduction; 2. Framework for planning and preparing for response to accidents in the transport of radioactive material; 3. Responsibilities for planning and preparing for response to accidents in the transport of radioactive material; 4. Planning for response to accidents in the transport of radioactive material; 5. Preparing for response to accidents in the transport of radioactive material; Appendix I: Features of the transport regulations influencing emergency response to transport accidents; Appendix II: Preliminary emergency response reference matrix; Appendix III: Guide to suitable instrumentation; Appendix IV: Overview of emergency management for a transport accident involving radioactive material; Appendix V: Examples of response to transport accidents; Appendix VI: Example equipment kit for a radiation protection team; Annex I: Example of guidance on emergency response to carriers; Annex II: Emergency response guide.

Development of supporting system for emergency response to maritime transport accidents involving radioactive material

International Nuclear Information System (INIS)

Odano, N.; Matsuoka, T.; Suzuki, H.

2004-01-01

National Maritime Research Institute has developed a supporting system for emergency response of competent authority to maritime transport accidents involving radioactive material. The supporting system for emergency response has functions of radiation shielding calculation, marine diffusion simulation, air diffusion simulation and radiological impact evaluation to grasp potential hazard of radiation. Loss of shielding performance accident and loss of sealing ability accident were postulated and impact of the accidents was evaluated based on the postulated accident scenario. Procedures for responding to emergency were examined by the present simulation results

Crash risk factors for interstate large trucks in North Carolina.

Science.gov (United States)

Teoh, Eric R; Carter, Daniel L; Smith, Sarah; McCartt, Anne T

2017-09-01

Provide an updated examination of risk factors for large truck involvements in crashes resulting in injury or death. A matched case-control study was conducted in North Carolina of large trucks operated by interstate carriers. Cases were defined as trucks involved in crashes resulting in fatal or non-fatal injury, and one control truck was matched on the basis of location, weekday, time of day, and truck type. The matched-pair odds ratio provided an estimate of the effect of various driver, vehicle, or carrier factors. Out-of-service (OOS) brake violations tripled the risk of crashing; any OOS vehicle defect increased crash risk by 362%. Higher historical crash rates (fatal, injury, or all crashes) of the carrier were associated with increased risk of crashing. Operating on a short-haul exemption increased crash risk by 383%. Antilock braking systems reduced crash risk by 65%. All of these results were statistically significant at the 95% confidence level. Other safety technologies also showed estimated benefits, although not statistically significant. With the exception of the finding that short-haul exemption is associated with increased crash risk, results largely bolster what is currently known about large truck crash risk and reinforce current enforcement practices. Results also suggest vehicle safety technologies can be important in lowering crash risk. This means that as safety technology continues to penetrate the fleet, whether from voluntary usage or government mandates, reductions in large truck crashes may be achieved. Practical application: Results imply that increased enforcement and use of crash avoidance technologies can improve the large truck crash problem. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

Presenting a conceptual pattern of HSE performance of oil trucks.

Science.gov (United States)

Ghaleh, Sahar; Omidvari, Manouchehr; Nassiri, Parvin; Momeni, Mansour; Lavasani, Seyed Mohammadreza Miri

2018-01-25

Accidents are among the main problems in the oil product supply chain. The most important effective factors in these events are the kind of trucks used and their health, safety, and environment (HSE) condition. The aim of this study was to present a conceptual pattern of the HSE performance of oil trucks in oil industries. In this study, 20 truck models (with fixed tanks), in use over different periods of time, were investigated. In this regard, the criteria and sub-criteria were first determined in two parts-carrier and tank-and weighted by fuzzy analytical hierarchy process (FAHP). The results showed that the most important sub-criteria regarding the HSE factors of the carrier were resistance and strength of the front and rear shields, the brake system, and the ventilation system. The most important sub-criteria regarding the HSE factors of the tank were tank shell thickness and a good tank design shape with respect to portable material. It should be noted that the weight of the criteria with each other and sub-criteria with each other are not equal. This issue is important for decision-making. The main reason for the use of trucks with the lowest score in developing countries is the lack of attention by managers to safety issues and international standards and agreements such as the ADR.

Causes of Fatal Accidents Involving Cranes in the Australian Construction Industry

OpenAIRE

Gharaie, Ehsan; Lingard, Helen; Cooke, Tracy

2015-01-01

In ten years from 2004 to 2013, 359 workers died in the Australian construction industry because of work related causes. This paper investigates crane-related fatalities in order to find the upstream causation of such accidents. The National Coroners’ Information System (NCIS) database was searched to identify fatal accidents in the construction industry involving the use of a crane.  The narrative description of the cases provided in the coroners’ findings and associated documents were conte...

Modelling Truck Weigh Stations’ Locations based on Truck Traffic Flow and Overweight Violation: A Case Study in Bosnia and Herzegovina

Directory of Open Access Journals (Sweden)

Mirsad Kulović

2018-04-01

Full Text Available The number of registered commercial freight vehicles is constantly increasing, increasing therefore as well the traffic load on the roads in Bosnia and Herzegovina. A significant part of freight vehicles moving along the main and regional roads are overloaded and cause significant damage to road infrastructure, affect road safety and result in an increase of emissions of harmful gases for people and the environment. The overloading rate is extremely high, in particular with 5-axle trucks representing 58.7%. The research showed that the increased overload level ranges from 10-20% of the maximum permissible weight. The importance of load limits was recognized early in the history of road development. This interrelation led directly to limitations on vehicle loads, and laws were enacted in many countries to establish the maximum allowable motor vehicle sizes and weights. Strict enforcement of motor vehicle size and weight laws is a step toward reducing motor vehicle size and weight violations, heavy truck accidents, and, even more, improving road maintenance, rehabilitation expenditures and road safety. Thus, based on the applied model the objective of this paper is to evaluate and optimize the locations of truck weigh stations on the road network of Bosnia and Herzegovina.

Causes of Fatal Accidents Involving Cranes in the Australian Construction Industry

Directory of Open Access Journals (Sweden)

Ehsan Gharaie

2015-05-01

Full Text Available In ten years from 2004 to 2013, 359 workers died in the Australian construction industry because of work related causes. This paper investigates crane-related fatalities in order to find the upstream causation of such accidents. The National Coroners’ Information System (NCIS database was searched to identify fatal accidents in the construction industry involving the use of a crane.  The narrative description of the cases provided in the coroners’ findings and associated documents were content analysed to identify the contributing causal factors within the context of each case. The findings show that the most frequent crane-related accident types were those that were struck by load, and electrocution. The most prevalent immediate circumstance causes were layout of the site and restricted space. The two most commonly identified shaping factors were physical site constraints and design of construction process. Inadequate risk management system was identified as the main originating influence on the accidents. This paper demonstrates that a systemic causation model can provide considerable insight into how originating influences, shaping factors, and immediate circumstances combine to produce accidents. This information is extremely useful in informing the development of prevention strategies, particularly in the case of commonly occurring accident types.

Under-reporting of accidents involving biological material by nursing professionals at a Brazilian emergency hospital.

Science.gov (United States)

Facchin, Luiza Tayar; Gir, Elucir; Pazin-Filho, Antonio; Hayashida, Miyeko; da Silva Canini, Silvia Rita Marin

2013-01-01

Pathogens can be transmitted to health professionals after contact with biological material. The exact number of infections deriving from these events is still unknown, due to the lack of systematic surveillance data and under-reporting. A cross-sectional study was carried out, involving 451 nursing professionals from a Brazilian tertiary emergency hospital between April and July 2009. Through an active search, cases of under-reporting of occupational accidents with biological material by the nursing team were identified by means of individual interviews. The Institutional Review Board approved the research project. Over half of the professionals (237) had been victims of one or more accidents (425 in total) involving biological material, and 23.76% of the accidents had not been officially reported using an occupational accident report. Among the underreported accidents, 53.47% were percutaneous and 67.33% were bloodborne. The main reason for nonreporting was that the accident had been considered low risk. The under-reporting rate (23.76%) was low in comparison with other studies, but most cases of exposure were high risk.

Concerning the structure of occupational accidents involving construction workers in the erection of nuclear power plants

International Nuclear Information System (INIS)

Nowak, B.; Roebenack, K.D.

1991-01-01

An investigation of 561 occupational accidents involving construction workers which took place during the construction of nuclear power plants failed to show any significant deviation in comparison with general construction as regards process classification, classification of accidents according to occupation and situation, and accidents severity. Occupational accidents which are typial for nuclear power plant construction are a rare exception. (orig.) [de

Urban risks of truck transport of radioactive material

International Nuclear Information System (INIS)

Mills, G.S.; Neuhauser, K.S.

1998-01-01

Truck transport of radioactive material (RAM), e.g., spent nuclear fuel (SNF), normally maximizes use of Interstate highways, which are safer and more efficient for truck transport in general. In the estimation of transportation risks, population bordering a route is a direct factor in determining consequences and an indirect factor in determining exposure times, accident probabilities and severities, and other parameters. Proposals to transport RAM may draw intense resistance from stakeholders based on concern for population concentrations along urban segments but the length of a route segment is also a determinative factor in estimating the transport risks. To quantify the relative importance of these two factors, a potential route for transport of SNF (strict use of Interstate highways) was selected and compared with a modified version that bypassed urban areas. The RADTRAN 4 code for transportation risk assessment, which was developed at Sandia National Laboratories, was used in the present study to assess the relative risks of SNF transportation for alternative routes. The results suggest that emphasis on Interstate highways minimizes total route and urban segment risks

Improvement of the mining technology with the ring movement scheme of the haul trucks

Directory of Open Access Journals (Sweden)

Slobodyanyuk R.V.

2016-04-01

Full Text Available The article describes the designed technology that allows to expand the use of the haul truck ring movement scheme and to reduce the share of an empty run time in the transportation cycle. A preliminary calculation of the efficiency of its usage has allowed to confirm the main advantages of this scheme over the existing one as follows: reducing the required number of transport for the needs of open-pit mine operation by increasing the productivity of mining trucks; decreasing the transport operating costs (some part of an empty truck movement occurs when the engine is switched off; dropping the probability of accidents (reduced a number of the counter transport maneuvers. The calculation showed the regularity of changes in the efficiency using the alternative scheme in relation to the basic one, which reflecting significantly higher effectiveness in situations with a smaller distance between the empty run sites of the ring scheme.

Dynamic simulation of collisions of heavy high-speed trucks with concrete barriers

International Nuclear Information System (INIS)

Itoh, Yoshito; Liu, Chunlu; Kusama, Ryuichi

2007-01-01

Real vehicle collision experiments on full-scale road safety barriers are important to determine the outcome of a vehicle versus barrier impact accident. However, such experiments require large investment of time and money. Numerical simulation has therefore been imperative as an alternative method for testing concrete barriers. In this research, spring subgrade models were first developed to simulate the ground boundary of concrete barriers. Both heavy trucks and concrete barriers were modeled using finite element methods (FEM) to simulate dynamic collision performances. Comparison of the results generated from computer simulations and on-site full-scale experiments demonstrated that the developed models could be applied to simulate the collision of heavy trucks with concrete barriers to provide the data to design new road safety barriers and analyze existing ones

Speed limiter integrated fatigue analyzer (SLIFA) for speed and fatigue control on diesel engine truck and bus

Science.gov (United States)

Wahyudi, Haris; Pranoto, Hadi; Leman, A. M.; Sebayang, Darwin; Baba, I.

2017-09-01

Every second, the number of road traffic deaths is increased globally with millions more sustaining severe injuries and living with long-term adverse health consequences. Jakarta alone in year 2015 had recorded 556 people died due to road accidents, approximately reached 6.231 road accident cases. The identified major contributory factors of such unfortunate events are both driver fatigue and over speeding habit especially related to the driving of truck and bus. This paper presents the idea on how to control the electronic system from input fuel system of injection pump and the combustion chamber engine will control the valve solenoid in injection pump which can lock and fuel will stop for moment, and speed limit can be success, by using sensor heart rate we can input reduce speed limit when fatigue detection driver. Integration process this tool can be relevant when Speed Limiter Integrated Fatigue Analyser (SLIFA) trial in the diesel engine for truck and bus, the result of this research Speed Limiter Integrated Fatigue Analyser (SLIFA) able to control speed of diesel engine for truck and bus almost 30km/h, 60km/h, and until 70 km/h. The installation of the sensor heart rate as the input speed limit SLIFA would work when the driver is detected to be in the fatigue condition. We make Speed Limiter Integrated Fatigue Analyser (SLIFA) for control and monitoring system for diesel engine in truck and bus. Speed Limiter Integrated Fatigue Analyser (SLIFA) system can save the historical of the speed record, fatigue, rpm, and body temperature of the driver.

Evaluating sustainability of truck weight regulations: A system dynamics view

Directory of Open Access Journals (Sweden)

Pei Liu

2015-11-01

Full Text Available Purpose: Targeting the problem of overload trucking in Highway Transportation of iron ore from Caofeidian to Tangshan (HTCT, this paper aims to assess long-term effects of alternative Truck Weight Regulation (TWR policies on sustainability of HTCT. Design/methodology/approach: A system dynamics model was established for policy evaluation. The model, composed of six interrelating modules, is able to simulate policies effects on trucking issues such as freight flow, truck traffic flow, pavement performance, highway transport capacity and trucking time, and further on the Cumulative Economic Cost (CEC including transport cost and time cost of freight owners and the Cumulative Social Cost (CSC including pavement maintenance cost, green house gas emission cost, air pollutants emission cost and traffic accidents cost, so the effects of TWR policies on sustainability of HTCT could be evaluated. Findings: According to different values of overload ratio which a TWR policy allows, alternative TWR policies are classified into three types, which are The Rigid Policy (TRP, The Moderate Policy (TMP and The Tolerant Policy (TTP. Results show that the best policy for sustainability of HTCT depends on the importance of CSC which is expected by the local government. To be specific, (1 if CSC is considered much less important than CEC, the local government should continue implementing the current TTP with the maximum overload ratio; (2 if CSC is considered much more important than CEC, then TRP is recommended; and (3 if CSC is considered slightly more important than CES, TMP with overload ratio of 80% is the best. Practical implications: Conclusions of this paper may help the local government design appropriate TWR policies to achieve sustainability of HTCT. Originality/value: To the best of our knowledge, this is the first effort to evaluate TWR policies on sustainability of regional freight transportation based on system dynamics modeling.

Single-vehicle and Multi-vehicle Accidents Involving Motorcycles in a Small City in China: Characteristics and Injury Patterns

Directory of Open Access Journals (Sweden)

Lili Xiong

2015-03-01

Full Text Available Introduction: There is a gap that involves examining differences between patients in single-vehicle (SV versus multi-vehicle (MV accidents involving motorcycles in Shantou, China, regarding the injury patterns and mortality the patients sustained. This study aims to address this gap and provide a basis and reference for motorcycle injury prevention. Method: Medical record data was collected between October 2002 and June 2012 on all motorcycle injury patients admitted to a hospital in the city of Shantou of the east Guangdong province in China. Comparative analysis was conducted between patients in SV accidents and patients in MV accidents regarding demographic and clinic characteristics, mortality, and injury patterns. Results: Approximately 48% (n = 1977 of patients were involved in SV accidents and 52% (n = 2119 were involved in MV accidents. The average age was 34 years. Collision of a motorcycle with a heavy vehicle/bus (4% was associated with a 34 times greater risk of death (RR: 34.32|95% CI: 17.43–67.57. Compared to patients involved in MV accidents, those involved in SV accidents were more likely to sustain a skull fracture (RR: 1.47|95% CI: 1.22–1.77, an open head wound (RR: 1.46|95% CI: 1.23–1.74, an intracranial injury (RR: 1.39|95% CI: 1.26–1.53, a superficial head injury (RR: 1.37|95% CI: 1.01–1.86, an injury to an organ (RR: 2.01|95% CI: 1.24–3.26, and a crushing injury (RR: 1.98|95% CI: 1.06–3.70 to the thorax or abdomen. However, they were less likely to sustain a spinal fracture (RR: 0.58|95% CI: 0.39–0.85, a pelvic fracture (RR: 0.22|95% CI: 0.11–0.46, an upper extremity fracture (RR: 0.75|95% CI: 0.59–0.96, or injuries to their lower extremities, except for a dislocation, sprain, or injury to a joint or ligament (RR: 0.82|95% CI: 0.49–1.36. Conclusion: The relative risk of death is higher for patients involved in multi-vehicle accidents than patients in single-vehicle accidents, especially when a

Highway accident involving radiopharmaceuticals near Brookhaven, Mississippi on December 3, 1983

International Nuclear Information System (INIS)

Mohr, P.B.; Mount, M.E.; Schwartz, M.W.

1985-04-01

A rear-end collision occurred between a passenger automobile and a luggage trailer carrying 84 packages, 76 of which contained radiopharmaceuticals, on US Highway 84 near Brookhaven, Mississippi on the afternoon of December 3, 1983. The purpose of this report is to document the mechanical circumstances of the accident, confirm the nature and quantity of radioactive materials involved, and assess the nature of the physical environment to which the packages were exposed and the response of the packages. The report consists of three major sections. The first deals wth the nature and circumstances of the accident and findings of fact. The second gives an accounting and description of the materials involved and the consequences of their exposure. The third gives an assessment and analysis of the mechanisms of damage and the conclusions which may be drawn from the investigation. 4 refs., 24 figs., 4 tabs

Potential Safety Benefit of the Blind Spot Detection System for Large Trucks on the Vulnerable Road Users in Taiwan

Directory of Open Access Journals (Sweden)

Wang Ming-Hang

2016-01-01

Full Text Available Considering motorcyclists, pedestrians and bicyclists as vulnerable road users (VRUs, more than 75 percent of the victims of fatal crashes involving large trucks in Taiwan are VRUs. Most crashes occurred at or were due to the blind spots of large trucks because of the size and traveling locations of the VRUs. This study applies typology and statistical methods to estimate the potential safety benefit of blind spot detection (BSD systems for large trucks on VRUs. The pre-crash scenarios associated with the blind spots of large trucks were derived by counting the maneuvers of large trucks and VRUs, prior to crashes, the truck drivers’ improper behaviors (cause of crashes, and the crash types. The number of crashes and fatalities were counted for the pre-crash scenario relevant to the BSD systems. A value of 0.8 of human machine interface factor (HMIF based on a previous study was applied to estimate the potential safety benefits of the BSD system. The results show that the implementation of BSD systems on all large trucks could help avoid about 24, 10, and 11 percent of large truck-involved crashes with pedestrians, bicycles, and motorcycles, respectively. The BSD systems could also save 5 pedestrians, 3 bicyclists, and 15 motorcyclists per year from crashes involving large trucks.

Full scale simulations of accidents on spent-nuclear-fuel shipping systems

International Nuclear Information System (INIS)

Yoshimura, H.R.

1978-01-01

In 1977 and 1978, five first-of-a-kind full scale tests of spent-nuclear-fuel shipping systems were conducted at Sandia Laboratories. The objectives of this broad test program were (1) to assess and demonstrate the validity of current analytical and scale modeling techniques for predicting damage in accident conditions by comparing predicted results with actual test results, and (2) to gain quantitative knowledge of extreme accident environments by assessing the response of full scale hardware under actual test conditions. The tests were not intended to validate the present regulatory standards. The spent fuel cask tests fell into the following configurations: crashes of a truck-transport system into a massive concrete barrier (100 and 130 km/h); a grade crossing impact test (130 km/h) involving a locomotive and a stalled tractor-trailer; and a railcar shipping system impact into a massive concrete barrier (130 km/h) followed by fire. In addition to collecting much data on the response of cask transport systems, the program has demonstrated thus far that current analytical and scale modeling techniques are valid approaches for predicting vehicular and cask damage in accident environments. The tests have also shown that the spent casks tested are extremely rugged devices capable of retaining their radioactive contents in very severe accidents

Assessing injury severity in bicyclists involved in traffic accidents to more effectively prevent fatal bicycle injuries in Japan.

Science.gov (United States)

Gomei, Sayaka; Hitosugi, Masahito; Ikegami, Keiichi; Tokudome, Shogo

2013-10-01

The objective of this study was to clarify the relationship between injury severity in bicyclists involved in traffic accidents and patient outcome or type of vehicle involved in order to propose effective measures to prevent fatal bicycle injuries. Hospital records were reviewed for all patients from 2007 to 2010 who had been involved in a traffic accident while riding a bicycle and were subsequently transferred to the Shock Trauma Center of Dokkyo Medical University Koshigaya Hospital. Patient outcomes and type of vehicle that caused the injury were examined. The mechanism of injury, Abbreviated Injury Scale (AIS) score, and Injury Severity Score (ISS) of the patient were determined. A total of 115 patients' records were reviewed. The mean patient age was 47.1 ± 27.4 years. The average ISS was 23.9, with an average maximum AIS (MAIS) score of 3.7. The ISS, MAIS score, head AIS score, and chest AIS score were well correlated with patient outcome. The head AIS score was significantly higher in patients who had died (mean of 4.4); however, the ISS, MAIS score, and head AIS score did not differ significantly according to the type of vehicle involved in the accident. The mean head AIS scores were as high as 2.4 or more for accidents involving any type of vehicle. This study provides useful information for forensic pathologists who suspect head injuries in bicyclists involved in traffic accidents. To effectively reduce bicyclist fatalities from traffic accidents, helmet use should be required for all bicyclists.

Analyzing injury severity factors at highway railway grade crossing accidents involving vulnerable road users: A comparative study.

Science.gov (United States)

Ghomi, Haniyeh; Bagheri, Morteza; Fu, Liping; Miranda-Moreno, Luis F

2016-11-16

The main objective of this study is to identify the main factors associated with injury severity of vulnerable road users (VRUs) involved in accidents at highway railroad grade crossings (HRGCs) using data mining techniques. This article applies an ordered probit model, association rules, and classification and regression tree (CART) algorithms to the U.S. Federal Railroad Administration's (FRA) HRGC accident database for the period 2007-2013 to identify VRU injury severity factors at HRGCs. The results show that train speed is a key factor influencing injury severity. Further analysis illustrated that the presence of illumination does not reduce the severity of accidents for high-speed trains. In addition, there is a greater propensity toward fatal accidents for elderly road users compared to younger individuals. Interestingly, at night, injury accidents involving female road users are more severe compared to those involving males. The ordered probit model was the primary technique, and CART and association rules act as the supporter and identifier of interactions between variables. All 3 algorithms' results consistently show that the most influential accident factors are train speed, VRU age, and gender. The findings of this research could be applied for identifying high-risk hotspots and developing cost-effective countermeasures targeting VRUs at HRGCs.

Kogi Truck Culture

OpenAIRE

Choy, Vivian

2011-01-01

Food trucks have become a large phenomenon in many parts of Southern California. In fact, the University of California, Los Angeles had begun permitting several food trucks to park on campus for hungry students, in response to the closure of the Bombshelter, a major campus food court. These trucks’ budding popularity has been spurred by the notable Kogi Trucks, which began its business serving those in Los Angeles. To explore the heart of this Kogi hype, I took two trips to the intersectio...

Risk of commercial truck fires in the United States : an exploratory data analysis

Science.gov (United States)

2012-06-29

Large trucks are involved in only 8 percent of fatal crashes per year, but 17 percent of fatal fires. The scope of the current body of research is limited. Studies have treated truck fires generally as a subset of vehicle fires or in their own right ...

Emergency response planning for transport accidents involving radioactive materials

International Nuclear Information System (INIS)

1982-03-01

The document presents a basic discussion of the various aspects and philosophies of emergency planning and preparedness along with a consideration of the problems which might be encountered in a transportation accident involving a release of radioactive materials. Readers who are responsible for preparing emergency plans and procedures will have to decide on how best to apply this guidance to their own organizational structures and will also have to decide on an emergency planning and preparedness philosophy suitable to their own situations

In depth analysis of urban accidents involving motorcycle and moped riders in France, construction of prototypical accident scenarios and prospects for their prevention. Poster

OpenAIRE

CLABAUX, N

2007-01-01

in France, in 2006, in spite of a low part of travel, motorcycle and moped riders accounted for 23% of all traffic fatalities and 31% of all injuries recorded. This extra risk is particularly marked in urban areas and in large cities. According to national accident statistics, in urban areas, accidents involving motorcycles and mopeds account for 20% and 23,6% respectively, of all injury accidents recorded. In the city of Paris, in 2005, powered two-wheelers accounted for 3% of all travel but...

Assessing crash risk considering vehicle interactions with trucks using point detector data.

Science.gov (United States)

Hyun, Kyung Kate; Jeong, Kyungsoo; Tok, Andre; Ritchie, Stephen G

2018-03-12

Trucks have distinct driving characteristics in general traffic streams such as lower speeds and limitations in acceleration and deceleration. As a consequence, vehicles keep longer headways or frequently change lane when they follow a truck, which is expected to increase crash risk. This study introduces several traffic measures at the individual vehicle level to capture vehicle interactions between trucks and non-trucks and analyzed how the measures affect crash risk under different traffic conditions. The traffic measures were developed using headways obtained from Inductive Loop Detectors (ILDs). In addition, a truck detection algorithm using a Gaussian Mixture (GM) model was developed to identify trucks and to estimate truck exposure from ILD data. Using the identified vehicle types from the GM model, vehicle interaction metrics were categorized into three groups based on the combination of leading and following vehicle types. The effects of the proposed traffic measures on crash risk were modeled in two different cases of prior- and non-crash using a case-control approach utilizing a conditional logistic regression. Results showed that the vehicle interactions between the leading and following vehicle types were highly associated with crash risk, and further showed different impacts on crash risk by traffic conditions. Specifically, crashes were more likely to occur when a truck following a non-truck had shorter average headway but greater headway variance in heavy traffic while a non-truck following a truck had greater headway variance in light traffic. This study obtained meaningful conclusions that vehicle interactions involved with trucks were significantly related to the crash likelihood rather than the measures that estimate average traffic condition such as total volume or average headway of the traffic stream. Copyright © 2018 Elsevier Ltd. All rights reserved.

Benefit of energy absorption by the truck in a frontal car-to-truck collision

NARCIS (Netherlands)

Coo, P.J.A. de; Adalian, C.

2000-01-01

EEVC Working Group 14 is investigating the effect of fixing energy absorbing front underrun protection systems (eaFUPS) to trucks instead of rigid devices in order to reduce the injury severity to car occupants in car-to-truck frontal collisions. Three car-to-truck crash tests with cars from

Domino effect in chemical accidents: main features and accident sequences

OpenAIRE

Casal Fàbrega, Joaquim; Darbra Roman, Rosa Maria

2010-01-01

The main features of domino accidents in process/storage plants and in the transportation of hazardous materials were studied through an analysis of 225 accidents involving this effect. Data on these accidents, which occurred after 1961, were taken from several sources. Aspects analyzed included the accident scenario, the type of accident, the materials involved, the causes and consequences and the most common accident sequences. The analysis showed that the most frequent causes a...

Communication of work accidents involving biological material: a study in the city of Santa Cruz do Sul/RS

Directory of Open Access Journals (Sweden)

Dayane Diehl

2012-07-01

Full Text Available Rationale and Objectives: Healthcare workers are constantly exposed to the risk of occupational accidents involving biological material. Thus the aim of the study was to develop a profile of workers involved in workplace accidents with biological materials in Santa Cruz do Sul, through the number of notifications made in information systems. Methods: Transversal retrospective study with a quantitative approach; data collection was carried out between the years 2008 and 2010 from medical records in the Municipal Reference Occupational Health Unit – UMREST – containing the notification via Individual Report of Accident Notification - RINA, and/or Work Accident Communication - CAT. Results: A total of 1,263 records were analyzed during the study period. There were 13 notifications in 2008, 7 cases in 2009 and 2 in 2010. Five records had CAT, 8 had RINA and 9 had RINA and CAT. The most frequently affected professional category was the nursing technician, with the highest frequency in 2008, followed by dentists and nurses. There was a higher prevalence of female workers, with 18 cases. The most prevalent age group was 20 to 49 years old. Conclusion: The study showed that women working in the nursingprofession at the productive-age group are the ones most often affected by work accidents involving biological material during the study period. The study results raise the suspicion of underreporting of accidents with biological material, considering the number of notifications in thesetting of records found in the investigated UMREST. KEYWORDS Wo rk-related accidents. Health care professional. Occupational accidents.

Analysis of a postulated accident scenario involving loss of forced flow in a LMFBR

International Nuclear Information System (INIS)

Moreira, M.L.

1985-01-01

A model to analyse a postulated accident scenario involving loss of forced flow in the reactor vessel of a LMFBR is used. Five phases of the accident are analysed: Natural Circulation, Subcooled Boiling, Nucleate Boiling, Core Dryout and Cladding melt. The heat conduction in the fuel cladding, coolant and lower and upper plenum are calculated by a lump-parameter model. Physical data of a prototype LMFBR reactor were used for the calculation. (author)

Transportation accidents/incidents involving radioactive materials (1971-1991)

International Nuclear Information System (INIS)

Cashwell, C.E.; McClure, J.D.

1993-01-01

In 1981, Sandia National Laboratories developed the Radioactive Materials Incident Report (RMIR) database to support its research and development activities for the U.S. Department of Energy (DOE). The RMIR database contains information on transportation accidents/incidents with radioactive materials that have occurred since 1971. The RMIR classifies a transportation accident/incident in one of six ways: as a transportation accident, a handling accident, a reported incident, missing or stolen, cask weeping, or other. This paper will define these terms and provide detailed examples of each. (J.P.N.)

Differences in passenger car and large truck involved crash frequencies at urban signalized intersections: an exploratory analysis.

Science.gov (United States)

Dong, Chunjiao; Clarke, David B; Richards, Stephen H; Huang, Baoshan

2014-01-01

The influence of intersection features on safety has been examined extensively because intersections experience a relatively large proportion of motor vehicle conflicts and crashes. Although there are distinct differences between passenger cars and large trucks-size, operating characteristics, dimensions, and weight-modeling crash counts across vehicle types is rarely addressed. This paper develops and presents a multivariate regression model of crash frequencies by collision vehicle type using crash data for urban signalized intersections in Tennessee. In addition, the performance of univariate Poisson-lognormal (UVPLN), multivariate Poisson (MVP), and multivariate Poisson-lognormal (MVPLN) regression models in establishing the relationship between crashes, traffic factors, and geometric design of roadway intersections is investigated. Bayesian methods are used to estimate the unknown parameters of these models. The evaluation results suggest that the MVPLN model possesses most of the desirable statistical properties in developing the relationships. Compared to the UVPLN and MVP models, the MVPLN model better identifies significant factors and predicts crash frequencies. The findings suggest that traffic volume, truck percentage, lighting condition, and intersection angle significantly affect intersection safety. Important differences in car, car-truck, and truck crash frequencies with respect to various risk factors were found to exist between models. The paper provides some new or more comprehensive observations that have not been covered in previous studies. Copyright © 2013 Elsevier Ltd. All rights reserved.

A highway accident involving unirradiated nuclear fuel in Springfield, Massachusetts, on December 16, 1991

International Nuclear Information System (INIS)

Carlson, R.W.; Fischer, L.E.

1992-06-01

In the early morning of Dec. 16, 1991, a severe accident occurred when a passenger vehicle traveling in the wrong direction collided with a tractor trailer carrying 24 unirradiated nuclear fuel assemblies in 12 containers on Interstate I-91 in Springfield, Massachusetts. The purpose of this report is to document the mechanical circumstances of the severe accident, confirm the nature and quantity of the radioactive materials involved, and assess the physical environment to which the containers were exposed and the response of the containers and their contents. The report consists of five major sections. The first section describes the circumstances and conditions of the accident and the finding of facts. The second describes the containers, the unirradiated nuclear fuel assemblies, and the tie down arrangement used for the trailer. The third describes the damage sustained during the accident to the tractor, trailer, containers, and unirradiated nuclear fuel assemblies. The fourth evaluates the accident environment and its effects on the containers and their contents. The final section gives conclusions derived from the analysis and fact finding investigation. During this severe accident, only minor injuries occurred, and at no time was the public health and safety at risk

The open-pit truck dispatching method based on the completion of production target and the truck flow saturation

Energy Technology Data Exchange (ETDEWEB)

Xing, J.; Sun, X. [Northeastern University, Shenyang (China)

2007-05-15

To address current problems in the 'modular dispatch' dynamic programming system widely used in open-pit truck real-time dispatching, two concepts for meeting production targets and truck flow saturation were proposed. Using truck flow programming and taking into account stochastic factors and transportation distance, truck real-time dispatching was optimised. The method is applicable to both shovel-truck match and mismatching and also to empty and heavy truck dispatching. In an open-pit mine the production efficiency could be increased by between 8% and 18%. 6 refs.

Assessment of the risk of transporting uranium hexafluoride by truck and train

International Nuclear Information System (INIS)

Geffen, C.A.; Johnson, J.F.; Davis, D.K.; Friley, J.R.; Ross, B.A.

1978-08-01

This report is the fifth in a series of studies of the risk of transporting potentially hazardous energy materials. The report presents an assessment of the risk of shipping uranium hexafluoride (UF 6 ) by truck and rail. The general risk assessment methodology, summarized in Section 3, used in this study is that developed for the first study in this series. The assessment includes the risks from release of uranium hexafluoride during truck or rail transport due to transportation accidents. The contribution to the risk of deteriorated or faulty packaging during normal transport was also considered. The report is sectioned to correspond to the specific analysis steps of the risk assessment model. The transportation system and accident environment are described in Sections 4 and 5. Calculation of the response of the shipping system to forces produced in transportation accidents are presented in Section 6 and the results of a survey to determine the condition of the package during transport are presented in Section 7. Sequences of events that could lead to a release of radioactive material from the shipping cask during transportation are postulated in Section 8 using fault tree analysis. These release sequences are evaluated in Sections 9 through 11, to determine both the likelihood and the possible consequences of each release. Supportive data and analyses are given in the appendices. The results of the risk assessment have been related to the year 1985, when it is projected that 100 GW of electric power will be generated annually by nuclear power plants. It was estimated that approximately 46,000 metric tons (MT) of natural UF 6 and 14,600 MT of enriched UF 6 would be shipped in the reference year

Characteristics of motorcyclists involved in road traffic accidents attended at public urgent and emergency services.

Science.gov (United States)

Mascarenhas, Márcio Dênis Medeiros; Souto, Rayone Moreira Costa Veloso; Malta, Deborah Carvalho; Silva, Marta Maria Alves da; Lima, Cheila Marina de; Montenegro, Marli de Mesquita Silva

2016-12-01

Injuries resulting from motorcycle road traffic accidents are an important public health issue in Brazil. This study aimed to describe the characteristics of motorcyclists involved in traffic accidents attended in public urgent and emergency services in the state capitals and the Federal District. This is a cross-sectional study based on data from the Violence and Accident Surveillance System (VIVA Survey) in 2014. Data were analyzed according to sociodemographic, event and attendance characteristics. Proportional differences between genders were analyzed by chi-square test (Rao-Scott) with 5% significance level. Motorcyclist-related attendances (n = 9,673) reported a prevalence of men (gender ratio = 3.2), young people aged 20-39 years (65.7%), black / brown (73.6%), paid work (76.4%). Helmet use was reported by 79.1% of the victims, 13.3% had consumed alcohol in the six hours prior to the accident, 41.4% of the events were related to the victim's work. Accidents were more frequent on weekends, in the morning and late afternoon. These characteristics can support the development of public accident prevention policies and health promotion.

Domino effect in chemical accidents: main features and accident sequences.

Science.gov (United States)

Darbra, R M; Palacios, Adriana; Casal, Joaquim

2010-11-15

The main features of domino accidents in process/storage plants and in the transportation of hazardous materials were studied through an analysis of 225 accidents involving this effect. Data on these accidents, which occurred after 1961, were taken from several sources. Aspects analyzed included the accident scenario, the type of accident, the materials involved, the causes and consequences and the most common accident sequences. The analysis showed that the most frequent causes are external events (31%) and mechanical failure (29%). Storage areas (35%) and process plants (28%) are by far the most common settings for domino accidents. Eighty-nine per cent of the accidents involved flammable materials, the most frequent of which was LPG. The domino effect sequences were analyzed using relative probability event trees. The most frequent sequences were explosion→fire (27.6%), fire→explosion (27.5%) and fire→fire (17.8%). Copyright © 2010 Elsevier B.V. All rights reserved.

Accidental poisoning in childhood: a multicentre survey. 2. The role of packaging in accidents involving medications.

Science.gov (United States)

Wiseman, H M; Guest, K; Murray, V S; Volans, G N

1987-07-01

To assess the effectiveness of child-resistant closures (CRCs) and unit dose packaging in preventing childhood poisoning with medications, a survey by 14 hospitals of accidental suspected poisoning in children under 5-years-old, was compared with a survey of a representative sample of households with children under 5 living in the catchment areas of the hospitals. Nine hundred and thirty-eight medications thought to have been ingested by 877 children were compared with 5827 medications found in households with children. The relationship between availability of packs or medications in the home and their involvement in accidents was quantified by means of an Accident Association Index (AAI). A low AAI indicated that the involvement of a pack or medication was less than expected from availability and therefore safe. A high AAI indicated that involvement was greater than expected and therefore unsafe. Medications involved in suspected poisoning were most frequently packed in containers without CRCs (63%) or transparent blisters (20%); both had high AAIs. CRCs, strips, sachets and opaque blisters had low AAIs. Analgesics, expectorants and gastrointestinal medications, had low AAIs, while oral contraceptives, hypnotics, sedative/tranquillizers, antidepressants, anticonvulsants, anti-emetics, and anti-infectives had high AAIs. Prescription medications were more frequently involved in accidents than over-the-counter (OTC) medications and had a higher AAI. Comparison of the AAIs of different kinds of medication in each of their various pack types showed that safe packaging reduced the risk from medications which had a high average AAI. Only 40% of medications were in their normal storage place at the time of the accident. Medicine and bathroom cabinets, and kitchen cupboards and drawers were the safest places to store medications. Handbags, fridges, and shelves or ledges in the bathroom were the most unsafe places. No pack had a low AAI when stored on open shelves

Risk of transporting plutonium dioxide and liquid plutonium nitrate by truck and rail

International Nuclear Information System (INIS)

Williams, L.D.; Hall, R.J.

1976-01-01

This paper presents an analysis method developed to assess the risk in the transportation of radioactive materials and demonstrates its application by summarizing the results of risk assessments of the shipment of plutonium dioxide powder and liquid plutonium nitrate by truck and rail in the United States. In the risk assessment, postulated release modes (series of events that could result in a release of radioactive material) are identified using the fault tree analysis method. Two categories of events that could contribute to a release during transportation are considered: accidents and substandard packaging conditions. The likelihood of basic events in these categories are determined from general accident experience, radioactive material shipping experience, engineering analysis, etc. Using the laws of combining probabilities, the likelihood of radioactive material release is then evaluated. Since accidents vary greatly in severity, the releases from these postulated events also vary in magnitude from the no release condition up through release of the entire package contents. The bases for the release quantities assigned to the postulated accidents sequences are discussed. The consequences of these postulated releases are evaluated based on the amount of plutonium estimated to be released to the environs, the probable weather conditions at the time of the accident, and population density downwind from the accident scene. The likelihood and consequence of postulated releases are coupled and expressed as a risk spectra. (author)

Vehicle to vehicle communications for trucks.

Science.gov (United States)

2014-01-01

The trucking industry is a critical component of American commerce. The American : Trucking Association estimates that over 80 percent of U.S. communities depend : exclusively on trucking for delivery of their goods and commodities

Development of offroad unmanned dump truck navigation system. Dump truck mujin soko system no kaihatsu ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Horii, Z [Nittetsu Mining Co. Ltd., Tokyo (Japan)

1992-08-25

A large offroad unmanned dump truck navigation system has been developed, and is in practical operation mounted on dump trucks at Torigatayama Limestone Quarry of Nittetsu Mining Company. The system functions in a manual dump truck navigation mode, wireless navigation mode, and unmanned control mode. The unmanned control mode further includes a mode to navigate the truck on a predetermined course with its data having been input in a computer and a mode that when the truck was moved on a course under a wireless control, the computer learns the course and drives the truck autonomously thereafter. The safety measures are divided into the hardware safety function to detect abnormalities in brakes and other vehicle parts, and the software safety functions of data communications, sensor action check, and prevention of collision of trucks with each other. The system has resulted in a productivity of average one-way travel distance of 345 m, and average unmanned navigation cycle time of 9 minutes and 26 seconds for a transportation efficiency of 541 t/hour/truck, having reached at least the manned operation level. 4 figs., 1 tab.

Optimization of shovel-truck system for surface mining

Energy Technology Data Exchange (ETDEWEB)

Ercelebi, S.G.; Bascetin, A. [Istanbul Technical University, Istanbul (Turkey). Mining Engineering Department

2009-07-15

In surface mining operations, truck haulage is the largest item in the operating costs, constituting 50 to 60% of the total. In order to reduce this cost, it is necessary to allocate and dispatch the trucks efficiently. This paper describes shovel and truck operation models and optimization approaches for the allocation and dispatching of trucks under various operating conditions. Closed queuing network theory is employed for the allocation of trucks and linear programming for the purpose of truck dispatching to shovels. A case study was applied for the Orhaneli open Pit Coal Mine in Turkey. This approach would provide the capability of estimating system performance measures (mine throughput, mean number of trucks, mean waiting time, etc.) for planning purposes when the truck fleet is composed of identical trucks. A computational study is presented to show how choosing the optimum number of trucks and optimum dispatching policy affect the cost of moving material in a truck-shovel system.

Emergency preparedness: medical management of nuclear accidents involving large groups of victims

International Nuclear Information System (INIS)

Parmentier, N.; Nenot, J.C.

1988-01-01

The treatment of overexposed individuals implies hospitalisation in a specialized unit applying hematological intense care. If the accident results in a small number of casualties, the medical management does not raise major problems in most of the countries, where specialized units exist, as roughly 7% of the beds are available at any time. But an accident which would involved tens or hundreds of people raises much more problems for hospitalization. Such problems are also completely different and will involve steps in the medical handling, mainly triage, (combined injuries), determination of whole body dose levels, transient hospitalization. In this case, preplanning is necessary, adapted to the system of medical care in case of a catastrophic event in the given Country, with the main basic principles : emergency concerns essentially the classical injuries (burns and trauma) - and contamination problems in some cases - treatment of radiation syndrome is not an emergency during the first days but some essential actions have to be taken such as early blood sampling for biological dosimetry and for HLa typing

The management of individuals involved in radiation accidents

Energy Technology Data Exchange (ETDEWEB)

Swindon, T N [Australian Radiation Lab., Melbourne (Australia)

1991-09-01

The author defines the objectives and the coverage of two radiation accident courses presented in 1990 by the US Radiation Emergency Assistance Centre and Training Site of the Oak Ridge Associated Universities together with some Australian Medical institutions. It is estimated that the courses, directed towards physicians, radiotherapists and nurses gave plenty practical advices and details on how to go about radiation accident managements. A manual on handling radiation accidents is also to be prepared after the courses.

Gas fuelled heavy-duty trucks for municipal services

Energy Technology Data Exchange (ETDEWEB)

Forsberg, A. (City of Helsinki Construction Services (Finland)); Hietanen, L. (Lassila and Tikanoja, Jyvaeskylae (Finland)); Nylund, N.-O. (TEC TransEnergy Consulting, Espoo (Finland))

2009-07-01

Helsinki City Public Works Department (HKR) and the environmental management company Lassila and Tikanoja joined forces to demonstrate the suitability of heavy-duty gas fuelled trucks for municipal services. HKR acquired two and Lassila and Tikanoja five Mercedes-Benz Econic trucks. HKR's trucks are equipped with interchangeable platforms, Lassila an Tikanoja's trucks with refuse collection equipment. The trucks are subjected to a two-year follow-up study to establish reliability, operational costs and exhaust emissions. Diesel trucks representing up-to-date technology are used as reference. If the gas fuelled trucks perform well, this can lead to increased numbers of natural gas trucks in municipal services, and in the long run to the introduction of biogas fuelled trucks. (orig.)

Communication of work accidents involving biological material: a study in the city of Santa Cruz do Sul/RS

OpenAIRE

Dayane Diehl; Karini da Rosa; Susimar Souza Rosa; Susane Beatriz Frantz Krug

2012-01-01

Rationale and Objectives: Healthcare workers are constantly exposed to the risk of occupational accidents involving biological material. Thus the aim of the study was to develop a profile of workers involved in workplace accidents with biological materials in Santa Cruz do Sul, through the number of notifications made in information systems. Methods: Transversal retrospective study with a quantitative approach; data collection was carried out between the years 2008 and 2010 from medical recor...

Emergency planning and preparedness for accidents involving radioactive materials used in medicine, industry, research and teaching

International Nuclear Information System (INIS)

1989-01-01

This Safety Series book should be considered as a technical guide aimed at the users of radioactive materials and the appropriate local and national authorities. It does not represent a single solution to the problems involved but rather draws the outlines of the plans and procedures that have to be developed in order to mitigate the consequences of an accident, should one occur. The preparation of local and national plans should follow the technical recommendations provided in this publication, with due consideration given to local factors which might vary from country to country (e.g. governmental systems, local legislation, quantities of radioactive materials involved). Several types of accidents are described, together with their possible radiological consequences. The basic principles of the protective measures that should be applied are discussed, and the principles of emergency planning and the measures needed to maintain preparedness for an operational response to an accident are outlined

Personality, Driving Behavior and Mental Disorders Factors as Predictors of Road Traffic Accidents Based on Logistic Regression.

Science.gov (United States)

Alavi, Seyyed Salman; Mohammadi, Mohammad Reza; Souri, Hamid; Mohammadi Kalhori, Soroush; Jannatifard, Fereshteh; Sepahbodi, Ghazal

2017-01-01

The aim of this study was to evaluate the effect of variables such as personality traits, driving behavior and mental illness on road traffic accidents among the drivers with accidents and those without road crash. In this cohort study, 800 bus and truck drivers were recruited. Participants were selected among drivers who referred to Imam Sajjad Hospital (Tehran, Iran) during 2013-2015. The Manchester driving behavior questionnaire (MDBQ), big five personality test (NEO personality inventory) and semi-structured interview (schizophrenia and affective disorders scale) were used. After two years, we surveyed all accidents due to human factors that involved the recruited drivers. The data were analyzed using the SPSS software by performing the descriptive statistics, t-test, and multiple logistic regression analysis methods. P values less than 0.05 were considered statistically significant. In terms of controlling the effective and demographic variables, the findings revealed significant differences between the two groups of drivers that were and were not involved in road accidents. In addition, it was found that depression and anxiety could increase the odds ratio (OR) of road accidents by 2.4- and 2.7-folds, respectively (P=0.04, P=0.004). It is noteworthy to mention that neuroticism alone can increase the odds of road accidents by 1.1-fold (P=0.009), but other personality factors did not have a significant effect on the equation. The results revealed that some mental disorders affect the incidence of road collisions. Considering the importance and sensitivity of driving behavior, it is necessary to evaluate multiple psychological factors influencing drivers before and after receiving or renewing their driver's license.

Personality, Driving Behavior and Mental Disorders Factors as Predictors of Road Traffic Accidents Based on Logistic Regression

Science.gov (United States)

Alavi, Seyyed Salman; Mohammadi, Mohammad Reza; Souri, Hamid; Mohammadi Kalhori, Soroush; Jannatifard, Fereshteh; Sepahbodi, Ghazal

2017-01-01

Background: The aim of this study was to evaluate the effect of variables such as personality traits, driving behavior and mental illness on road traffic accidents among the drivers with accidents and those without road crash. Methods: In this cohort study, 800 bus and truck drivers were recruited. Participants were selected among drivers who referred to Imam Sajjad Hospital (Tehran, Iran) during 2013-2015. The Manchester driving behavior questionnaire (MDBQ), big five personality test (NEO personality inventory) and semi-structured interview (schizophrenia and affective disorders scale) were used. After two years, we surveyed all accidents due to human factors that involved the recruited drivers. The data were analyzed using the SPSS software by performing the descriptive statistics, t-test, and multiple logistic regression analysis methods. P values less than 0.05 were considered statistically significant. Results: In terms of controlling the effective and demographic variables, the findings revealed significant differences between the two groups of drivers that were and were not involved in road accidents. In addition, it was found that depression and anxiety could increase the odds ratio (OR) of road accidents by 2.4- and 2.7-folds, respectively (P=0.04, P=0.004). It is noteworthy to mention that neuroticism alone can increase the odds of road accidents by 1.1-fold (P=0.009), but other personality factors did not have a significant effect on the equation. Conclusion: The results revealed that some mental disorders affect the incidence of road collisions. Considering the importance and sensitivity of driving behavior, it is necessary to evaluate multiple psychological factors influencing drivers before and after receiving or renewing their driver’s license. PMID:28293047

Personality, Driving Behavior and Mental Disorders Factors as Predictors of Road Traffic Accidents Based on Logistic Regression

Directory of Open Access Journals (Sweden)

Seyyed Salman Alavi

2017-01-01

Full Text Available Background: The aim of this study was to evaluate the effect of variables such as personality traits, driving behavior and mental illness on road traffic accidents among the drivers with accidents and those without road crash. Methods: In this cohort study, 800 bus and truck drivers were recruited. Participants were selected among drivers who referred to Imam Sajjad Hospital (Tehran, Iran during 2013-2015. The Manchester driving behavior questionnaire (MDBQ, big five personality test (NEO personality inventory and semi-structured interview (SADS were used. After two years, we surveyed all accidents due to human factors that involved the recruited drivers. The data were analyzed using the SPSS software by performing the descriptive statistics, t-test, and multiple logistic regression analysis methods. P values less than 0.05 were considered statistically significant. Results: In terms of controlling the effective and demographic variables, the findings revealed significant differences between the two groups of drivers that were and were not involved in road accidents. In addition, it was found that depression and anxiety could increase the odds ratio (OR of road accidents by 2.4- and 2.7-folds, respectively (P=0.04, P=0.004. It is noteworthy to mention that neuroticism alone can increase the odds of road accidents by 1.1-fold (P=0.009, but other personality factors did not have a significant effect on the equation. Conclusion: The results revealed that some mental disorders affect the incidence of road collisions. Considering the importance and sensitivity of driving behavior, it is necessary to evaluate multiple psychological factors influencing drivers before and after receiving or renewing their driver’s license.

Use of casual tree method for investigation of incidents and accidents involving radioactive materials

International Nuclear Information System (INIS)

Vasconcelos, Vanderley de; Senne Junior, Murillo; Marques, Raissa Oliveira

2013-01-01

There are many methodologies used for investigation of accidents to facilitate the search of the factors that cause these events in different areas of industry. These can be called proactive methods, if they are used before the occurrence of the events, or reactive methods that are applied after the occurrence of the incident or accident, and are used as a basis of information to prevent further events. One of these methods is the Causal Tree Method (CTM). The basic idea of this technique is that incidents and accidents result from variations in usual processes. These variations can be related to the individual, the task, the material or the environment. The tree starts with the end event (incident or accident) and works backwards. The facts relating to the end event are used in the construction of the causal tree. The end event is the starting point and only the facts that contributed to the incident or accident should be selected. The analyst has to identify and list the variations and then display them in the analytic tree, showing causal relations. The objective of this paper is to test the application of the CTM method in investigation of incidents and accidents involving radioactive materials, in order to evaluate its efficiency on finding the typical factors causing these events. (author)

Examination of offsite radiological emergency measures for nuclear reactor accidents involving core melt

International Nuclear Information System (INIS)

Aldrich, D.C.; McGrath, P.E.; Rasmussen, N.C.

1978-06-01

Evacuation, sheltering followed by population relocation, and iodine prophylaxis are evaluated as offsite public protective measures in response to nuclear reactor accidents involving core-melt. Evaluations were conducted using a modified version of the Reactor Safety Study consequence model. Models representing each measure were developed and are discussed. Potential PWR core-melt radioactive material releases are separated into two categories, ''Melt-through'' and ''Atmospheric,'' based upon the mode of containment failure. Protective measures are examined and compared for each category in terms of projected doses to the whole body and thyroid. Measures for ''Atmospheric'' accidents are also examined in terms of their influence on the occurrence of public health effects

Truckstop - and Truck - Electrification

International Nuclear Information System (INIS)

Skip Yeakel

2001-01-01

The conclusions of this paper are: 0.5-1.5 G/H and/or BUSG/Y-how much time and money will it take to quantify and WHY BOTHER TO DO SO? No shortage of things to do re truckstop-+ truck - electrification; Better that government and industry should put many eggs in lots of baskets vs. all in one or few; Best concepts will surface as most viable; Economic appeal better than regulation or brute force; Launch Ground Freight Partnership and give it a chance to work; Demonstration is an effective means to educate, and learn from, customers-learning is a two way street; Research, Development, Demonstration, and Deployment (RD 3) are all important but only deployment gets results; TSE can start small in numbers of spaces to accommodate economically inspired growth but upfront plans should be made for expansion if meaningful idle reduction is to follow via TE; 110VAC 15A service/ parking space is minimal-if infrastructure starts like this, upfront plans must be made to increase capacity; Increased electrification of truckstop and truck alike will result in much better life on the road; Improved sleep will improve driver alertness and safety; Reduced idling will significantly reduce fuel use and emissions; Universal appeal for DOD, DOE, DOT, EPA, OEMs, and users alike; Clean coal, gas, hydro, nuclear, or wind energy sources are all distinctly American means by which to generate electricity; Nothing can compete with diesel fuel to serve mobile truck needs; stationary trucks are like power plants-they don't move and should NOT be powered by petroleum products whenever possible; Use American fueled power plants-electricity-to serve truck idling needs wherever practical to do so; encourage economic aspect; Create and reward industry initiatives to reduce fuel use; Eliminate FET on new trucks, provide tax credits (non highway fuel use and investment), provide incentives based on results; Encourage newer/ cleaner truck use; solicit BAAs with mandatory OEM/ fleet participation/ lead

An Examination of Commercial Motor Vehicle Hours of Service Safety Regulation

Science.gov (United States)

2016-09-01

moved to further expand the knowledge with respect to the incentives provided to truck drivers through the lens of perishable inventory theory and its...method utilizing the theoretical foundation of perishable inventory theory , and 3) a statistical analysis on accidents caused by or involving truck...truck driving industry. Perishable inventory theory is used to understand how companies and truck drivers operate within this regulatory

2015 E-Truck Task Force: Key Barriers Affecting E-Truck Adoption, Industry and Policy Implications, and Recommendations to Move the Market Forward

OpenAIRE

Brotherton, Tom; Gilde, Alycia; Tomic, Jasna

2016-01-01

CALSTART’s E-Truck Task Force (ETTF) produced a report outlining the markets for electric drive trucks (E-Trucks), the prime barriers facing their success and provided key findings and recommendations to support expanding E-Truck adoption. Four key findings have been identified by the E-Truck Task Force as barriers currently affecting the growth and viability of E-Truck sales

Traffic collisions between electric mobility devices (wheelchairs) and motor vehicles: Accidents, hubris, or self-destructive behavior?

Science.gov (United States)

LaBan, Myron M; Nabity, Thomas S

2010-07-01

This study had its genesis in a personally observed collision between a motor vehicle and a motorized wheelchair (electric mobility device) on a busy street in the middle of the block at an unmarked crossing. To the observer, at the time, this appeared to be a suicidal act. This investigation was initiated to both delineate the number of these crashes nationally and understand this phenomena as a potentially planned act of self-destruction. An initial survey of police reports was immediately frustrated by an inability to separate motor vehicle and electric mobility device collisions from the much larger group that involved ambulatory citizens because both types were classified together as "pedestrian" accidents. Instead, the search engine NexisLexis was used to identify 107 newspaper articles each of which described a motor vehicle and electric mobility device accident. In the motor vehicle and electric mobility device collisions, men predominated women (3:1 ratio) with an average age of 56 yrs. Sixty of these accidents were fatal. Ninety-four percent involved an electric mobility device and 6% a manual wheelchair. In 50% of the cases, the motor vehicle was a truck, van, or sport utility vehicle. Fifty percent occurred at dusk or dawn or at night. The electric mobility device occupant was cited as the guilty party in 39% of the cases and the driver of the motor vehicle in 27%. Twenty percent were unwitnessed hit-and-run accidents, whereas "no fault" was found in 8% of the cases. Although many accidents do happen by chance, when an electric mobility device operator openly challenges busy traffic by attempting to traverse it in the middle of the block at an unmarked crossing, predisposing psychosocial factors must also be considered. Hubris or premeditated self-destructive behavior or both need to be explored as preeminent issues with reference to the prodromal of the "accident process."

Business plan for Gourmet Food Truck in Helsinki

OpenAIRE

Mulmi, Mukesh

2015-01-01

This thesis work is about food truck and food truck industry in Finland. In Finland, Culinary scenes are booming and growing but, the food truck concept is new to Finland. Food truck industry is very young and currently, there is a hype for food truck and people are admiring new cuisines. Author himself is working as a cook. And he is passionate about food and restaurant industry. The main purpose of the thesis was to explore more about food truck industry in Finland and create the busine...

Stake-holder involvement in the management of rural areas after an accident

International Nuclear Information System (INIS)

Nisbet, A.F.

2001-01-01

Widespread contamination of the food chain following a nuclear accident could have considerable consequences for European farming and food industries. For the purposes of contingency planning it is important to bring together the many and diverse stakeholders who would be involved in intervention so that strategies can be developed for maintaining agricultural production and food safety. This type of approach has been successfully implemented in the UK through the setting up of the Agriculture and Food Countermeasures Working Group. Building on this initiative, the European Commission under the auspices of its 5. Framework Programme is funding a thematic network in which similar stakeholder groups are being established in four other Member States. These national groups contain individuals involved in making policy decisions within government departments and agencies, regulatory authorities, the water, milk and farming industries, the retail trade and consumer groups, as well as individuals with specialist expertise. The stakeholder network will provide a European focus for tackling future nuclear accidents and assist in the harmonization of policies and strategies between Member States. This paper gives an overview of the approaches being adopted and discusses the achievements and expected benefits of stakeholder engagement. (author)

Injury protection and accident causation parameters for vulnerable road users based on German In-Depth Accident Study GIDAS.

Science.gov (United States)

Otte, Dietmar; Jänsch, Michael; Haasper, Carl

2012-01-01

Within a study of accident data from GIDAS (German In-Depth Accident Study), vulnerable road users are investigated regarding injury risk in traffic accidents. GIDAS is the largest in-depth accident study in Germany. Due to a well-defined sampling plan, representativeness with respect to the federal statistics is also guaranteed. A hierarchical system ACASS (Accident Causation Analysis with Seven Steps) was developed in GIDAS, describing the human causation factors in a chronological sequence. The accordingly classified causation factors - derived from the systematic of the analysis of human accident causes ("7 steps") - can be used to describe the influence of accident causes on the injury outcome. The bases of the study are accident documentations over ten years from 1999 to 2008 with 8204 vulnerable road users (VRU), of which 3 different groups were selected as pedestrians n=2041, motorcyclists n=2199 and bicyclists n=3964, and analyzed on collisions with cars and trucks as well as vulnerable road users alone. The paper will give a description of the injury pattern and injury mechanisms of accidents. The injury frequencies and severities are pointed out considering different types of VRU and protective measures of helmet and clothes of the human body. The impact points are demonstrated on the car, following to conclusion of protective measures on the vehicle. Existing standards of protection devices as well as interdisciplinary research, including accident and injury statistics, are described. With this paper, a summarization of the existing possibilities on protective measures for pedestrians, bicyclists and motorcyclists is given and discussed by comparison of all three groups of vulnerable road users. Also the relevance of special impact situations and accident causes mainly responsible for severe injuries are pointed out, given the new orientation of research for the avoidance and reduction of accident patterns. 2010 Elsevier Ltd. All rights reserved.

Predicted occurrence rate of severe transportation accidents involving large casks

International Nuclear Information System (INIS)

Dennis, A.W.

1978-01-01

A summary of the results of an investigation of the severities of highway and railroad accidents as they relate to the shipment of large radioactive materials casks is discussed. The accident environments considered are fire, impact, crash, immersion, and puncture. For each of these environments, the accident severities and their predicted frequencies of occurrence are presented. These accident environments are presented in tabular and graphic form to allow the reader to evaluate the probabilities of occurrence of the accident parameter severities he selects

Health promotion in the trucking setting: Understanding Dutch truck drivers' road to healthy lifestyle changes.

Science.gov (United States)

Boeijinga, Anniek; Hoeken, Hans; Sanders, José

2016-10-17

The working environment, the nature of the work, and the characteristics of truck drivers as a social group typically pose great challenges for the truck drivers' health and health promotion activities aiming to improve it. The purpose was to obtain a better understanding of (a) Dutch truck drivers' perceptions of health and lifestyle themes, and (b) the challenges they experience in their pursuit of a more healthy lifestyle, as a guiding framework for the development of health interventions targeting this occupational group. In this qualitative study, we conducted and analyzed 20 semi-structured interviews and seven cases of participant observations with Dutch truck drivers. Grounded theory was used to analyze the data. Our findings illustrate that Dutch truck drivers wish to improve their lifestyle but have unproductive associations with concepts of healthy living as well as a tendency to downplay their health risks. In addition, they experience barriers within their work and personal environment that prevent them from translating their intentions into actual lifestyle changes. Based on the insights derived from the interviews, we discuss recommendations for the development of more effective health promotion interventions for truck drivers.

Risk Factors for Cardiovascular Disease, Metabolic Syndrome and Sleepiness in Truck Drivers

Directory of Open Access Journals (Sweden)

Antonio de Padua Mansur

2015-01-01

Full Text Available AbstractBackground:Truck driver sleepiness is a primary cause of vehicle accidents. Several causes are associated with sleepiness in truck drivers. Obesity and metabolic syndrome (MetS are associated with sleep disorders and with primary risk factors for cardiovascular diseases (CVD. We analyzed the relationship between these conditions and prevalence of sleepiness in truck drivers.Methods:We analyzed the major risk factors for CVD, anthropometric data and sleep disorders in 2228 male truck drivers from 148 road stops made by the Federal Highway Police from 2006 to 2011. Alcohol consumption, illicit drugs and overtime working hours were also analyzed. Sleepiness was assessed using the Epworth Sleepiness Scale.Results:Mean age was 43.1 ± 10.8 years. From 2006 to 2011, an increase in neck (p = 0.011 and abdominal circumference (p < 0.001, total cholesterol (p < 0.001, triglyceride plasma levels (p = 0.014, and sleepiness was observed (p < 0.001. In addition, a reduction in hypertension (39.6% to 25.9%, p < 0.001, alcohol consumption (32% to 23%, p = 0.033 and overtime hours (52.2% to 42.8%, p < 0.001 was found. Linear regression analysis showed that sleepiness correlated closely with body mass index (β = 0.19, Raj2 = 0.659, p = 0.031, abdominal circumference (β = 0.24, Raj2 = 0.826, p = 0.021, hypertension (β = -0.62, Raj2 = 0.901, p = 0.002, and triglycerides (β = 0.34, Raj2 = 0.936, p = 0.022. Linear multiple regression indicated that hypertension (p = 0.008 and abdominal circumference (p = 0.025 are independent variables for sleepiness.Conclusions:Increased prevalence of sleepiness was associated with major components of the MetS.

Safety climate and the distracted driving experiences of truck drivers.

Science.gov (United States)

Swedler, David I; Pollack, Keshia M; Agnew, Jacqueline

2015-07-01

For truck drivers, distracted driving is a workplace behavior that increases occupational injury risk. We propose safety climate as an appropriate lens through which researchers can examine occupational distracted driving. Using a mixed methods study design, we surveyed truck drivers using the Safety Climate Questionnaire (SCQ) complemented by semi-structured interviews of experts on distracted driving and truck safety. Safety climate was assessed by using the entire SCQ as an overall climate score, followed by factor analysis that identified the following safety climate factors: Communications and Procedures; Management Commitment; and Work Pressure. In multivariate regression, the overall safety climate scale was associated with having ever experienced a crash and/or distraction-involved swerving. Interview participants described how these SCQ constructs could affect occupational distracted driving. To reduce distraction-related crashes in their organizations, management can adhere to safe policies and procedures, invest in engineering controls, and develop safer communication procedures. © 2015 Wiley Periodicals, Inc.

Health physics evaluation of an accident involving acute overexposure to a radiography source

International Nuclear Information System (INIS)

Basson, J.K.; Hanekom, A.P.; Coetzee, F.C.; Lloyd, D.C.

1981-10-01

An accident, involving the loss of an iridium-192 radiographic source and the subsequent serious overexposure of a third party, is described. Health physics aspects, particularly dosimetrical aspects are addressed and compared with results obtained by means of chromosome aberration dosimetry. Details are provided on the medical observations and treatment of the patient [af

Shipping container response to severe highway and railway accident conditions: Main report

International Nuclear Information System (INIS)

Fischer, L.E.; Chou, C.K.; Gerhard, M.A.; Kimura, C.Y.; Martin, R.W.; Mensing, R.W.; Mount, M.E.; Witte, M.C.

1987-02-01

This report describes a study performed by the Lawrence Livermore National Laboratory to evaluate the level of safety provided under severe accident conditions during the shipment of spent fuel from nuclear power reactors. The evaluation is performed using data from real accident histories and using representative truck and rail cask models that likely meet 10 CFR 71 regulations. The responses of the representative casks are calculated for structural and thermal loads generated by severe highway and railway accident conditions. The cask responses are compared with those responses calculated for the 10 CFR 71 hypothetical accident conditions. By comparing the responses it is determined that most highway and railway accident conditions fall within the 10 CFR 71 hypothetical accident conditions. For those accidents that have higher responses, the probabilities anf potential radiation exposures of the accidents are compared with those identified by the assessments made in the ''Final Environmental Statement on the Transportation of Radioactive Material by Air and other Modes,'' NUREG-0170. Based on this comparison, it is concluded that the radiological risks from spent fuel under severe highway and railway accident conditions as derived in this study are less than risks previously estimated in the NUREG-0170 document

Zagreb and Tenerife: Airline Accidents Involving Linguistic Factors

Science.gov (United States)

Cookson, Simon

2009-01-01

The International Civil Aviation Organization (ICAO) is currently implementing a program to improve the language proficiency of pilots and air traffic controllers worldwide. In justifying the program, ICAO has cited a number of airline accidents that were at least partly caused by language factors. Two accidents cited by ICAO are analysed in this…

Determinants of fuel consumption in mining trucks

International Nuclear Information System (INIS)

Dindarloo, Saeid R.; Siami-Irdemoosa, Elnaz

2016-01-01

Analysis of fuel consumption in a large surface mine, during more than 5000 cycles of material transportation, revealed considerable variability in the data. Truck fuel estimation based on the mining truck manufacturers' manuals/estimates is not capable of capturing this variability in the fuel consumption data. Partial least squares regression and autoregressive integrated moving average methods were employed to examine the effect of cyclic activities on fuel consumption, and to recommend relevant remedies for consumption reduction. Proper modifications of the operation can result in improved cycle times. Consequently, minimizing some cyclic activities would enhance energy efficiency. The truck “empty idle time” was a major contributor to unnecessary fuel consumption. Since the truck queues at shovels are a major component of the “empty idle time”, decisions should be reviewed to reduce the truck queues at loading points. Improved dispatching strategies, optimal muck pile shape and size distribution, and improved shovel/loader operator skills are effective preventive measures to minimize truck flow bottlenecks at loading points, and thus to improve energy efficiency at mines. - Highlights: • A large fleet of mining trucks consumes considerable amounts of energy. • Current energy models do not consider the effect of site-specific mining conditions. • A new methodology based on material handling cyclic activities is proposed. • Fuel consumption rates in different truck operating modes are determined. • The new model is compared with the truck manufacturer's energy consumption guideline.

19 CFR 123.41 - Truck shipments transiting Canada.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Truck shipments transiting Canada. 123.41 Section... OF THE TREASURY CUSTOMS RELATIONS WITH CANADA AND MEXICO United States and Canada In-Transit Truck Procedures § 123.41 Truck shipments transiting Canada. (a) Manifest required. Trucks with merchandise...

Experience in the analysis of accidents and incidents involving the transport of radioactive materials

International Nuclear Information System (INIS)

Warner-Jones, S.M.; Hughes, J.S.; Shaw, K.B.

2002-01-01

Some half a million packages containing radioactive materials are transported to, from and within the UK annually. Accidents and incidents involving these shipments are rare. However, there is always the potential for such an event, which could lead to a release of the contents of a package or an increase in radiation level caused by damaged shielding. These events could result in radiological consequences for transport workers. As transport occurs in the public environment, such events could also lead to radiation exposures of members of the public. The UK Department for Transport (DfT), together with the Health and Safety Executive (HSE) have supported, for almost 20 years, work to compile, analyse and report on accidents and incidents that occur during the transport of radioactive materials. Annual reports on these events have been produced for twelve years. The details of these events are recorded in the Radioactive Materials Transport Event Database (RAMTED) maintained by the National Radiological Protection Board on behalf of the DfT and HSE. Information on accidents and incidents dates back to 1958. RAMTED currently includes information of 708 accidents and incidents, covering the period 1958 to 2000. This paper presents a summary of the data covering this period, identifying trends and lessons learned together with a discussion of some examples. It was found that, historically, the most significant exposures were received as a result of accidents involving the transport of industrial radiography sources. However, the frequency and severity of these events has decreased considerably in the later years of this study due to improvements in training, awareness and equipment. The International Atomic Energy Agency and the Nuclear Energy Agency, have established the international nuclear event scale (INES), which is described in detail in a users' guide. The INES has been revised to fully include transport events, and the information in RAMTED has been reviewed

Statistical aspects of carbon fiber risk assessment modeling. [fire accidents involving aircraft

Science.gov (United States)

Gross, D.; Miller, D. R.; Soland, R. M.

1980-01-01

The probabilistic and statistical aspects of the carbon fiber risk assessment modeling of fire accidents involving commercial aircraft are examined. Three major sources of uncertainty in the modeling effort are identified. These are: (1) imprecise knowledge in establishing the model; (2) parameter estimation; and (3)Monte Carlo sampling error. All three sources of uncertainty are treated and statistical procedures are utilized and/or developed to control them wherever possible.

Mitigating Wind Induced Truck Crashes

Science.gov (United States)

2009-12-25

Dangerous weather and high wind in particular, is a common contributing factor in truck crashes. High wind speeds have been documented as a perennial cause of truck crashes in Kansas and other Great Plains states. The possibility of reducing such cra...

Fuel Cell Powered Lift Truck

Energy Technology Data Exchange (ETDEWEB)

Moulden, Steve [Sysco Food Service, Houston, TX (United States)

2015-08-20

This project, entitled “Recovery Act: Fuel Cell-Powered Lift Truck Sysco (Houston) Fleet Deployment”, was in response to DOE funding opportunity announcement DE-PS36-08GO98009, Topic 7B, which promotes the deployment of fuel cell powered material handling equipment in large, multi-shift distribution centers. This project promoted large-volume commercialdeployments and helped to create a market pull for material handling equipment (MHE) powered fuel cell systems. Specific outcomes and benefits involved the proliferation of fuel cell systems in 5-to 20-kW lift trucks at a high-profile, real-world site that demonstrated the benefits of fuel cell technology and served as a focal point for other nascent customers. The project allowed for the creation of expertise in providing service and support for MHE fuel cell powered systems, growth of existing product manufacturing expertise, and promoted existing fuel cell system and component companies. The project also stimulated other MHE fleet conversions helping to speed the adoption of fuel cell systems and hydrogen fueling technology. This document also contains the lessons learned during the project in order to communicate the successes and difficulties experienced, which could potentially assist others planning similar projects.

Estimation of Crash Severity on Mountainous Freeways in Chongqing

Directory of Open Access Journals (Sweden)

Yunwei Meng

2017-01-01

Full Text Available Mountainous freeways always suffer from accidents due to special terrain, weather conditions, driving environment, and so on. Based on the records of 898 accidents that occurred on mountainous freeways in Chongqing during the past 6 years, the partial proportional odds model is used to identify the factors affecting the accident severity. The time of the accident, season, involvement of trucks, accident characteristics, speeding, maximum driving experience of involved drivers, and weather and road conditions are found to be important for the levels of accident severity. Zero to 6 a.m. and 19 to 24 p.m. are the times prone to serious traffic accidents. The probability of serious traffic accidents in summer and autumn is greater than that in spring and winter. Once a truck is involved in an accident, the consequence is often more severe. Turnover and speeding will result in a grave accident. When there is an experienced driver, the probability of serious traffic accidents is low. The fog is extremely unfavorable weather conditions. The probability of serious accident happening in the downgrade, ramp, curve, bridge, and tunnel sections is greater than the others. The results aim to provide valuable reference for traffic safety on mountainous freeways.

Fuel Cell Hydroge Manifold for Lift Trucks

DEFF Research Database (Denmark)

Hosseinzadeh, Elham

. Battery driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need long time to recharge and may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...

A comprehensive review of rollover accidents involving vehicles equipped with Electronic Stability Control (ESC) systems.

Science.gov (United States)

Padmanaban, Jeya; Shields, Leland E; Scheibe, Robert R; Eyges, Vitaly E

2008-10-01

This study investigated 478 police accident reports from 9 states to examine and characterize rollover crashes involving ESC-equipped vehicles. The focus was on the sequence of critical events leading to loss of control and rollover, and the interactions between the accident, driver, and environment. Results show that, while ESC is effective in reducing loss of control leading to certain rollover crashes, its effectiveness is diminished in others, particularly when the vehicle departs the roadway or when environmental factors such as slick road conditions or driver factors such as speeding, distraction, fatigue, impairment, or overcorrection are present.

Uso de anfetaminas por motoristas de caminhão em rodovias do Estado de São Paulo: um risco à ocorrência de acidentes de trânsito? Amphetamine use by truck drivers on highways of Sao Paulo State: a risk for the occurrence of traffic accidents?

Directory of Open Access Journals (Sweden)

Mauricio Yonamine

2013-05-01

Full Text Available No Brasil, é comum o uso de anfetaminas por motoristas de caminhão, o que pode culminar na ocorrência de acidentes de trânsito. O objetivo deste artigo é estimar a prevalência do uso de anfetaminas entre caminhoneiros. Motoristas (N = 134 foram abordados em duas rodovias do Estado de São Paulo e solicitados a responder um questionário, assim como a fornecer uma amostra de urina para realização de análises toxicológicas. Todos os dados foram analisados em Stata 8.0. Todos os participantes eram do sexo masculino, de idade média de 40,8 anos e de baixa escolaridade. A presença de anfetaminas foi detectada em 10,8% das amostras de urina, cujo uso foi justificado para manter a vigília durante o trabalho. O uso de anfetaminas foi detectado entre caminhoneiros em rodovias de São Paulo. Cessado o efeito estimulante, a sonolência advinda de uma possível privação de sono diminui a atenção e o bom desempenho na direção, predispondo o condutor aos acidentes de trânsito e seus custos relacionados.The use of amphetamines in Brazil is common among truck drivers, which may be an important factor in the occurrence of traffic accidents. This article seeks to estimate the prevalence of amphetamine use among truck drivers. Drivers (N = 134 were stopped on two different highways in Sao Paulo state and they were asked to answer a questionnaire and provide a urine sample for toxicological analysis. All data were analyzed on Stata 8.0. All participants were males with low levels of schooling, whose mean age was 40.8 years. The presence of amphetamines was detected in 10.8% of all urine samples collected, being commonly justified in order to make truck drivers able to maintain their state of awareness. Amphetamine use was detected among truck drivers on Sao Paulo highways. The problem is that when the stimulant effects wear off, sleepiness due to sleep deprivation reduces concentration and good driver performance, making drivers vulnerable to

Environmental impact of accidents involving radioactive material shipping systems

International Nuclear Information System (INIS)

Yoshimura, H.R.; Pope, R.B.; Huerta, M.; Nilson, R.H.

1978-01-01

Four full-scale spent fuel cask crash tests have been performed, including two head-on truck-barrier impacts (100 and 135 km/h), one railcar-barrier impact (130 km/h), and one locomotive grade crossing impact (130 km/h). Releases to the environment were limited to seepage of about 100 cc of cavity liquid from the cask head in the 135 km/h truck impact test and a slight head seal air leak in the 130 km/h locomotive grade crossing test. These releases were well within the limits specified by the NRC regulations, would have been easily cleaned up, and would have caused little effect on the environment and virtually no risk to the public. To further evaluate cask capability, the crashed spent-fuel rail cask system was fire tested. The cask withstood 90 minutes of a fully engulfing hydrocarbon pool fire while maintaining its structural integrity. At approximately 100 minutes into the fire test, the outer shell of the cask cracked resulting in the partial loss of lead radiation shielding. The failure of the shell was attributed to poor quality control during the original fabrication of the cask in the early 1960's. Present regulatory standards would prevent such occurrences in casks built and licensed today. In addition, the test was much more severe than the qualification criteria specified by present licensing requirements. 4 tables, 13 figures

South Coast Air Quality Management District Truck Testing | Transportation

Science.gov (United States)

Research | NREL South Coast Air Quality Management District Truck Evaluation South Coast Air Quality Management District Truck Evaluation Photo of heavy-duty truck cab. Electric drayage truck Cargo Transportation project, conducted in partnership with the South Coast Air Quality Management

Biomass accident investigations – missed opportunities for learning and accident prevention

DEFF Research Database (Denmark)

Hedlund, Frank Huess

2017-01-01

The past decade has seen a major increase in the production of energy from biomass. The growth has been mirrored in an increase of serious biomass related accidents involving fires, gas explosions, combustible dust explosions and the release of toxic gasses. There are indications that the number...... of bioenergy related accidents is growing faster than the energy production. This paper argues that biomass accidents, if properly investigated and lessons shared widely, provide ample opportunities for improving general hazard awareness and safety performance of the biomass industry. The paper examines...... selected serious accidents involving biogas and wood pellets in Denmark and argues that such opportunities for learning were missed because accident investigations were superficial, follow-up incomplete and information sharing absent. In one particularly distressing case, a facility saw a repeat accident...

The Myth - Food Truck

OpenAIRE

Otálora Salgado, Esteban

2015-01-01

Food truck de comida típica colombiana fusión que espera solucionar la percepción que se tiene acerca de la comida callejera. Para ello, se ha realizado un estudio donde se identifica el problema y se plantea como solución la creación de un food truck que cumpla con todos los estándares de calidad y a su vez innove.

Investigating accidents involving aircraft manufactured from polymer composite materials

Science.gov (United States)

Dunn, Leigh

This study looks into the examination of polymer composite wreckage from the perspective of the aircraft accident investigator. It develops an understanding of the process of wreckage examination as well as identifying the potential for visual and macroscopic interpretation of polymer composite aircraft wreckage. The in-field examination of aircraft wreckage, and subsequent interpretations of material failures, can be a significant part of an aircraft accident investigation. As the use of composite materials in aircraft construction increases, the understanding of how macroscopic failure characteristics of composite materials may aid the field investigator is becoming of increasing importance.. The first phase of this research project was to explore how investigation practitioners conduct wreckage examinations. Four accident investigation case studies were examined. The analysis of the case studies provided a framework of the wreckage examination process. Subsequently, a literature survey was conducted to establish the current level of knowledge on the visual and macroscopic interpretation of polymer composite failures. Relevant literature was identified and a compendium of visual and macroscopic characteristics was created. Two full-scale polymer composite wing structures were loaded statically, in an upward bending direction, until each wing structure fractured and separated. The wing structures were subsequently examined for the existence of failure characteristics. The examination revealed that whilst characteristics were present, the fragmentation of the structure destroyed valuable evidence. A hypothetical accident scenario utilising the fractured wing structures was developed, which UK government accident investigators subsequently investigated. This provided refinement to the investigative framework and suggested further guidance on the interpretation of polymer composite failures by accident investigators..

Medium Truck Duty Cycle Data from Real-World Driving Environments: Final Report

Energy Technology Data Exchange (ETDEWEB)

Lascurain, Mary Beth [ORNL; Franzese, Oscar [ORNL; Capps, Gary J [ORNL; Siekmann, Adam [ORNL; Thomas, Neil [ORNL; LaClair, Tim J [ORNL; Barker, Alan M [ORNL; Knee, Helmut E [ORNL

2012-11-01

Since the early part of the 20th century, the US trucking industry has provided a safe and economical means of moving commodities across the country. At present, nearly 80% of US domestic freight movement involves the use of trucks. The US Department of Energy (DOE) is spearheading a number of research efforts to improve heavy vehicle fuel efficiencies. This includes research in engine technologies (including hybrid and fuel cell technologies), lightweight materials, advanced fuels, and parasitic loss reductions. In addition, DOE is developing advanced tools and models to support heavy vehicle research and is leading the 21st Century Truck Partnership and the SuperTruck development effort. Both of these efforts have the common goal of decreasing the fuel consumption of heavy vehicles. In the case of SuperTruck, a goal of improving the overall freight efficiency of a combination tractor-trailer has been established. This Medium Truck Duty Cycle (MTDC) project is a critical element in DOE s vision for improved heavy vehicle energy efficiency; it is unique in that there is no other existing national database of characteristic duty cycles for medium trucks based on collecting data from Class 6 and 7 vehicles. It involves the collection of real-world data on medium trucks for various situational characteristics (e.g., rural/urban, freeway/arterial, congested/free-flowing, good/bad weather) and looks at the unique nature of medium trucks drive cycles (stop-and-go delivery, power takeoff, idle time, short-radius trips). This research provides a rich source of data that can contribute to the development of new tools for FE and modeling, provide DOE a sound basis upon which to make technology investment decisions, and provide a national archive of real-world-based medium-truck operational data to support energy efficiency research. The MTDC project involved a two-part field operational test (FOT). For the Part-1 FOT, three vehicles each from two vocations (urban transit and

On-site transportation and handling of uranium-233 special nuclear material: Preliminary hazards and accident analysis. Final

International Nuclear Information System (INIS)

Solack, T.; West, D.; Ullman, D.; Coppock, G.; Cox, C.

1995-01-01

U-233 Special Nuclear Material (SNM) currently stored at the T-Building Storage Areas A and B must be transported to the SW/R Tritium Complex for repackaging. This SNM is in the form of oxide powder contained in glass jars which in turn are contained in heat sealed double polyethylene bags. These doubled-bagged glass jars have been primarily stored in structural steel casks and birdcages for approximately 20 years. The three casks, eight birdcages, and one pail/pressure vessel will be loaded onto a transport truck and moved over an eight day period. The Preliminary Hazards and Accident Analysis for the on-site transportation and handling of Uranium-233 Special Nuclear Material, documented herein, was performed in accordance with the format and content guidance of DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, dated July 1994, specifically Chapter Three, Hazard and Accident Analysis. The Preliminary Hazards Analysis involved detailed walkdowns of all areas of the U-233 SNM movement route, including the T-Building Storage Area A and B, T-Building truck tunnel, and the roadway route. Extensive discussions were held with operations personnel from the Nuclear Material Control Group, Nuclear Materials Accountability Group, EG and G Mound Security and the Material Handling Systems Transportation Group. Existing documentation related to the on-site transportation of hazardous materials, T-Building and SW/R Tritium Complex SARs, and emergency preparedness/response documentation were also reviewed and analyzed to identify and develop the complete spectrum of energy source hazards

Personal radiation burden for a truck driver on a five-day Budapest-Kijev-Budapest round trip

International Nuclear Information System (INIS)

Feher, I.

1999-01-01

A truck route was filed from 30 June 1986 to 5 July 1986 from Budapest to Kiev and back. The trip took 50 hours driving and 86 hours waiting. The radiation dose due to the Chernobyl accident to the driver has been estimated. The driver was estimated to an exposure of 0.1 mSv dose which is about 1/25 of the average annual exposure of the population. Deterministic radiation injury could be caused by 10000 times of the above dose. (R.P.)

The "No Trucks" Design Challenge

Science.gov (United States)

Roman, Harry T.

2007-01-01

Large tractor-trailers have a reputation of being involved in rather horrific accidents, often involving death and carnage among smaller passenger vehicles. The giant rigs, according to some transportation experts, may have outlived their usefulness on crowded highways, and perhaps it is time that people rethink their presence on the roads. In…

Raley's LNG Truck Site Final Data Report

Energy Technology Data Exchange (ETDEWEB)

Battelle

1999-07-01

Raley's is a 120-store grocery chain with headquarters in Sacramento, California, that has been operating eight heavy-duty LNG trucks (Kenworth T800 trucks with Cummins L10-300G engines) and two LNG yard tractors (Ottawa trucks with Cummins B5.9G engines) since April 1997. This report describes the results of data collection and evaluation of the eight heavy-duty LNG trucks compared to similar heavy-duty diesel trucks operating at Raley's. The data collection and evaluation are a part of the U.S. Department of Energy (DOE)/National Renewable Energy Laboratory (NREL) Alternative Fuel Truck Evaluation Project.

Reducing truck emissions at container terminals in a low carbon economy

DEFF Research Database (Denmark)

Chen, Gang; GOVINDAN, Kannan; Golias, Mihalis M.

2013-01-01

This study proposes a methodology to optimize truck arrival patterns to reduce emissions from idling truck engines at marine container terminals. A bi-objective model is developed minimizing both truck waiting times and truck arrival pattern change. The truck waiting time is estimated via...... a queueing network. Based on the waiting time, truck idling emissions are estimated. The proposed methodology is evaluated with a case study, where truck arrival rates vary over time. We propose a Genetic Algorithm based heuristic to solve the resulting problem. Result shows that, a small shift of truck...... arrivals can significantly reduce truck emissions, especially at the gate....

Legal weight truck cask model impact limiter response

International Nuclear Information System (INIS)

Meinert, N.M.; Shappert, L.B.

1989-01-01

Dynamic and quasi-static quarter-scale model testing was performed to supplement the analytical case presented in the Nuclear Assurance Corporation Legal Weight Truck (NAC LWT) cask transport licensing application. Four successive drop tests from 9.0 meters (30 feet) onto an unyielding surface and one 1.0-meter (40-inch) drop onto a scale mild steel pin 3.8 centimeters (1.5 inches) in diameter, corroborated the impact limiter design and structural analyses presented in the licensing application. Quantitative measurements, made during drop testing, support the impact limiter analyses. High-speed photography of the tests confirm that only a small amount of energy is elastically stored in the aluminum honeycomb and that oblique drop slapdown is not significant. The qualitative conclusion is that the limiter protected LWT cask will not sustain permanent structural damage and containment will be maintained, subsequent to a hypothetical accident, as shown by structural analyses

Assessment of the radiological risks of road transport accidents involving Type A packages

International Nuclear Information System (INIS)

Lange, F.; Fett, H.J.; Schwarz, G.; Raffestin, D.; Schneider, T.; Gelder, R.; S. Hughes, J.; B. Shaw, K.; Hedberg, B.; Simenstad, P.; Svahn, B.; Heinen, J.F.A. van; Jansma, R.

2001-01-01

An assessment and evaluation of the potential radiological risks of transport accidents involving Type A package shipments by road have been performed by five EU Member States, France, Germany, Sweden, The Netherlands, and the UK. The analysis involved collection and analysis of information on a national basis related to the type, volume, and characteristics of Type A package consignments, the associated radioactive traffic, and the expected frequency and consequences of potential vehicular road transport accidents. It was found that the majority of Type A packaged radioactive material shipments by road is related to applications of non-special form radioactive material, i.e. radiopharmaceuticals, radiochemicals etc., in medicine, research, and industry and special form material contained in radiography and other radiation sources, e.g. gauging equipment. The annual volumes of Type A package shipments of radiopharmaceuticals and radiochemicals by road differ considerably between the participating EU Member States from about 12,000 Type A packages in Sweden to about 240,000 in the Netherlands. The broad range reflects to a large extent the supply of radioactive material for the national populations and the production and distribution operations prevailing in the participating EU Member States (some are producer countries, others are not!). Very few standard package designs weighing from about 1-25 kg are predominant in Type A package shipments in all participating countries. Type A packages contain typically a range of radioactivity from a few mega becquerels to a few tens of giga becquerels, the average package activity contents is in terms of fractions of A 2 about 0.01, i.e. about one hundredth of a Type A package contents limits. Based on a probabilistic risk assessment method it has been concluded that the expected frequencies of occurrence of vehicular road transport accidents with the potential to result in an environmental release - including radiologically

Accident history, risk perception and traffic safe behaviour.

Science.gov (United States)

Ngueutsa, Robert; Kouabenan, Dongo Rémi

2017-09-01

This study clarifies the associations between accident history, perception of the riskiness of road travel and traffic safety behaviours by taking into account the number and severity of accidents experienced. A sample of 525 road users in Cameroon answered a questionnaire comprising items on perception of risk, safe behaviour and personal accident history. Participants who reported involvement in more than three accidents or involvement in a severe accident perceived road travel as less risky and also reported behaving less safely compared with those involved in fewer, or less severe accidents. The results have practical implications for the prevention of traffic accidents. Practitioner Summary: The associations between accident history, perceived risk of road travel and safe behaviour were investigated using self-report questionnaire data. Participants involved in more than three accidents, or in severe accidents, perceived road travel as less risky and also reported more unsafe behaviour compared with those involved in fewer, or less severe accidents. Campaigns targeting people with a less serious, less extensive accident history should aim to increase awareness of hazards and the potential severity of their consequences, as well as emphasising how easy it is to take the recommended preventive actions. Campaigns targeting those involved in more frequent accidents, and survivors of serious accidents, should address feelings of invulnerability and helplessness.

Naturalistic Study of Truck Following Behavior

Science.gov (United States)

2016-04-01

Volpe conducted the Naturalistic study of truck following behavior to gain a better understanding of how trucks follow other vehicles in the real world, with the ultimate goal of supporting the Federal Highway Administration in the development of aut...

Design basis for resistance to shock and vibration of radioactive material packages greater than one ton in truck transport (draft standard for trial use and comment)

International Nuclear Information System (INIS)

Anon.

1984-01-01

This standard specifies minimum design values for shock and vibration in highway transport, by truck or by tractor-trailer combination, for fuel and irradiation experiments when package weight exceeds one ton. Shock values correspond to normal transport over rough roads and to minor accidents such as backing into a loading dock. Vibration values correspond to normal transport; any large-amplitude vibration resulting from rough road conditions or a minor accident is treated as shock. This standard includes recommended methods of application to the design of packaging and tiedown systems

System for selection of radiation source transfer trucks

International Nuclear Information System (INIS)

Tanimoto, Yoshinori; Ito, Kojiro.

1970-01-01

A device for selection of trucks each of which load and transfer a radiation source to an irradiation room above a water pool is installed at the end of a pair of rails fixed to the bottom of the pool. This device is equipped with a number of laterally shiftable rail pairs which may be brought into successive alignment with the fixed rails and is adapted to receive, carry and fix a truck on each rail pair. If one of said trucks is selected for irradiation in a desired irradiation room, the rail pair carrying this truck is shifted to align and couple with the fixed rail pair whereupon the truck is driven and transferred to a position on the fixed rails below the desired room and elevated thereinto. Accordingly, a plurality of trucks can optionally be shunted on a line of fixed rails without unloading the respective radiation sources. (Ohno, Y.)

Trusted Truck(R) II (phase A).

Science.gov (United States)

2009-01-01

The Trusted Truck Program was initiated in 2003 as a joint effort by NTRCI, Volvo and UT. The vision of the Trusted Truck program is to develop a secure and "trusted" transport solution from pickup to delivery. The program's objective is to incre...

Seroepidemiology of Toxoplasma gondii infection in drivers involved in road traffic accidents in the metropolitan area of Guadalajara, Jalisco, Mexico.

Science.gov (United States)

Galván-Ramírez, Ma de la Luz; Sánchez-Orozco, Laura Verónica; Rodríguez, Laura Rocío; Rodríguez, Saúl; Roig-Melo, Enrique; Troyo Sanromán, Rogelio; Chiquete, Erwin; Armendáriz-Borunda, Juan

2013-10-11

The prevalence of toxoplasmosis in the general population of Guadalajara, Mexico, is around 32%. Toxoplasmosis can cause ocular lesions and slowing of reaction reflexes. Latent toxoplasmosis has been related with traffic accidents. We aimed to assess the prevalence of anti-Toxoplasma gondii antibodies and visual impairments related with traffic accidents in drivers from the metropolitan Guadalajara. We prospectively evaluated the prevalence of IgG and IgM anti-T. gondii antibodies in 159 individuals involved in traffic accidents, and in 164 control drivers never involved in accidents. Cases of toxoplasmosis reactivation or acute infection were detected by PCR in a subset of 71 drivers studied for the presence of T. gondii DNA in blood samples. Ophthalmologic examinations were performed in drivers with IgG anti-T. gondii antibodies in search of ocular toxoplasmosis. Fifty-four (34%) traffic accident drivers and 59 (36%) controls were positive to IgG anti-T. gondii antibodies (p = 0.70). Among the 113 seropositive participants, mean anti-T. gondii IgG antibodies titers were higher in traffic accident drivers than in controls (237.9 ± 308.5 IU/ml vs. 122.9 ± 112.7 IU/ml, respectively; p = 0.01 by Student's t test, p = 0.037 by Mann-Whitney U test). In multivariate analyses, anti-T. gondii IgG antibody titers were consistently associated with an increased risk of traffic accidents, whereas age showed an inverse association. The presence of IgM-anti-T. gondii antibodies was found in three (1.9%) subjects among traffic accident drives, and in two (1.2%) controls. Three (4.2%) samples were positive for the presence of T. gondii DNA, all among seropositive individuals. No signs of ocular toxoplasmosis were found in the entire cohort. Moreover, no other ocular conditions were found to be associated with the risk of traffic accidents in a multivariate analysis. Anti-T. gondii antibody titers are associated with the risk of traffic accidents. We could not determine any

Conservatism in effective dose calculations for accident events involving fuel reprocessing waste tanks.

Science.gov (United States)

Bevelacqua, J J

2011-07-01

Conservatism in the calculation of the effective dose following an airborne release from an accident involving a fuel reprocessing waste tank is examined. Within the regulatory constraints at the Hanford Site, deterministic effective dose calculations are conservative by at least an order of magnitude. Deterministic calculations should be used with caution in reaching decisions associated with required safety systems and mitigation philosophy related to the accidental release of airborne radioactive material to the environment.

The Nuclear Emergency Assistance Team, a mobile intervention facility for nuclear accidents

International Nuclear Information System (INIS)

Koelzer, W.

1975-01-01

A nuclear emergency assistance team consisting of a vehicle pool and a stock of technical equipment was set up for operation in case of major reactor accidents. The equipment is kept in 6 containers which can be shipped on trucks, by rail or by helicopter or plane. Technical equipment and tasks of each container are briefly explained. Special transport vehicles for remote handling of contaminated material are described. (ORU) [de

Idle emissions from medium heavy-duty diesel and gasoline trucks.

Science.gov (United States)

Khan, A B M S; Clark, Nigel N; Gautam, Mridul; Wayne, W Scott; Thompson, Gregory J; Lyons, Donald W

2009-03-01

Idle emissions data from 19 medium heavy-duty diesel and gasoline trucks are presented in this paper. Emissions from these trucks were characterized using full-flow exhaust dilution as part of the Coordinating Research Council (CRC) Project E-55/59. Idle emissions data were not available from dedicated measurements, but were extracted from the continuous emissions data on the low-speed transient mode of the medium heavy-duty truck (MHDTLO) cycle. The four gasoline trucks produced very low oxides of nitrogen (NOx) and negligible particulate matter (PM) during idle. However, carbon monoxide (CO) and hydrocarbons (HCs) from these four trucks were approximately 285 and 153 g/hr on average, respectively. The gasoline trucks consumed substantially more fuel at an hourly rate (0.84 gal/hr) than their diesel counterparts (0.44 gal/hr) during idling. The diesel trucks, on the other hand, emitted higher NOx (79 g/hr) and comparatively higher PM (4.1 g/hr), on average, than the gasoline trucks (3.8 g/hr of NOx and 0.9 g/hr of PM, on average). Idle NOx emissions from diesel trucks were high for post-1992 model year engines, but no trends were observed for fuel consumption. Idle emissions and fuel consumption from the medium heavy-duty diesel trucks (MHDDTs) were marginally lower than those from the heavy heavy-duty diesel trucks (HHDDTs), previously reported in the literature.

Acceptance test procedure for core sample trucks

International Nuclear Information System (INIS)

Smalley, J.L.

1995-01-01

The purpose of this Acceptance Test Procedure is to provide instruction and documentation for acceptance testing of the rotary mode core sample trucks, HO-68K-4600 and HO-68K-4647. The rotary mode core sample trucks were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Acceptance testing of the rotary mode core sample trucks will verify that the design requirements have been met. All testing will be non-radioactive and stand-in materials shall be used to simulate waste tank conditions. Compressed air will be substituted for nitrogen during the majority of testing, with nitrogen being used only for flow characterization

Accident information needs

International Nuclear Information System (INIS)

Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

1992-01-01

A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information

Accident information needs

Energy Technology Data Exchange (ETDEWEB)

Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

1992-12-31

A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information.

Accident information needs

Energy Technology Data Exchange (ETDEWEB)

Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

1992-01-01

A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information.

Application of Chaos Theory in Trucks' Overloading Enforcement

Directory of Open Access Journals (Sweden)

Abbas Mahmoudabadi

2013-01-01

Full Text Available Trucks' overloading is considered as one of the most substantial concerns in road transport due to a possible road surface damage, as well as, are less reliable performance of trucks' braking system. Sufficient human resource and adequate time scheduling are to be planned for surveying trucks' overloading; hence, it seems required to prepare an all-around model to be able to predict the number of overloaded vehicles. In the present research work, the concept of chaos theory has been utilized to predict the ratio of trucks which might be guessed overloaded. The largest Lyapunov exponent is utilized to determine the presence of chaos using experimental data and concluded that the ratio of overloaded trucks reflects chaotic behavior. The prediction based on chaos theory is compared with the results of simple smoothing and moving average methods according to the well-known criterion of mean square errors. The results have also revealed that the chaotic prediction model would act more capably comparing the analogous methods including simple smoothing and moving average to predict the ratio of passing trucks to be possibly overloaded.

Operations experience with the NAC-1 legal weight truck cask

International Nuclear Information System (INIS)

Viebrock, J.M.; Hoffman, C.C.

1978-01-01

The first three years of operation of Nuclear Assurance Corporation's (NAC) four (4) NAC-1 Casks have demonstrated that shipments of spent fuel, fuel rods and other highly irradiated reactor components can be moved routinely by legal weight truck transport. Shipments of these materials have involved some 800,000 miles of highway travel and cask handling at some fifteen different nuclear facilities. This paper presents details on NAC's operations experience with these casks including cask description, cask handling (loading and unloading), pre-shipment testing, facility turnaround and transit times, operator exposure, transport vehicles and shipper/carrier/cask owner responsibilities, actual experience with regard to facility interfacing requirements and operational procedures. Cask and equipment utilization is discussed together with the methods used to control operation costs and to improve the economics of truck transport

Norcal Prototype LNG Truck Fleet: Final Results

Energy Technology Data Exchange (ETDEWEB)

2004-07-01

U.S. DOE and National Renewable Energy Laboratory evaluated Norcal Waste Systems liquefied natural gas (LNG) waste transfer trucks. Trucks had prototype Cummins Westport ISXG engines. Report gives final evaluation results.

Investigating accidents involving aircraft manufactured from polymer composite materials

OpenAIRE

Dunn, Leigh

2013-01-01

This thesis looks into the examination of polymer composite wreckage from the perspective of the aircraft accident investigator. It develops an understanding of the process of wreckage examination as well as identifying the potential for visual and macroscopic interpretation of polymer composite aircraft wreckage. The in-field examination of aircraft wreckage, and subsequent interpretations of material failures, can be a significant part of an aircraft accident investigation. ...

Real world efficiency of retrofit partial-flow diesel particulate filters for trucks

International Nuclear Information System (INIS)

Van Asch, R.; Verbeek, R.; Ligterink, N.; Kadijk, G.

2009-11-01

In 2006 the Dutch Ministry of Housing, Spatial Planning and the Environment (VROM) introduced an incentive scheme for retrofitting diesel particulate filters on Euro II and Euro III trucks. This scheme involves both partial flow and full flow diesel particulate filters (also called semi-open or open respectively wall-flow or closed filters). In the period 2007 till January 2009 about 15,000 partial flow filters and 8,000 full flow diesel particulate filters were installed. The minimum filtration efficiency requirement for the partial flow diesel particulate filters is 50% during the type approval test. In 2008 an engine dynamometer test programme was conducted to measure the filtration efficiency of retrofit open particulates filters of heavy trucks. This led to somewhat disappointing results with average filtration efficiencies in the range of 5-20% during city and national motorway driving conditions up to 20-40% during long distance motorway driving. This result leads to two main questions: (1) Is this result also representative for medium heavy trucks used for delivery, and (2) do similar efficiencies show up also in tests on entire vehicles, tested under conditions as close as possible to their real world usage profile. To this end, an additional measurement programme was defined, which is reported here. The objective of the study reported here is to determine the real world filtration efficiency of retrofit partial flow particulate filters for a number of trucks under different driving conditions such as city and motorway driving. The emphasis should be on medium heavy trucks typically used for national delivery.

NIOSH national survey of long-haul truck drivers: Injury and safety

Science.gov (United States)

Chen, Guang X.; Sieber, W. Karl; Lincoln, Jennifer E.; Birdsey, Jan; Hitchcock, Edward M.; Nakata, Akinori; Robinson, Cynthia F.; Collins, James W.; Sweeney, Marie H.

2015-01-01

Approximately 1,701,500 people were employed as heavy and tractor-trailer truck drivers in the United States in 2012. The majority of them were long-haul truck drivers (LHTDs). There are limited data on occupational injury and safety in LHTDs, which prompted a targeted national survey. The National Institute of Occupational Safety and Health conducted a nationally representative survey of 1265 LHTDs at 32 truck stops across the contiguous United States in 2010. Data were collected on truck crashes, near misses, moving violations, work-related injuries, work environment, safety climate, driver training, job satisfaction, and driving behaviors. Results suggested that an estimated 2.6% of LHTDs reported a truck crash in 2010, 35% reported at least one crash while working as an LHTD, 24% reported at least one near miss in the previous 7 days, 17% reported at least one moving violation ticket and 4.7% reported a non-crash injury involving days away from work in the previous 12 months. The majority (68%) of non-crash injuries among company drivers were not reported to employers. An estimate of 73% of LHTDs (16% often and 58% sometimes) perceived their delivery schedules unrealistically tight; 24% often continued driving despite fatigue, bad weather, or heavy traffic because they needed to deliver or pick up a load at a given time; 4.5% often drove 10 miles per hours or more over the speed limit; 6.0% never wore a seatbelt; 36% were often frustrated by other drivers on the road; 35% often had to wait for access to a loading dock; 37% reported being noncompliant with hours-of-service rules (10% often and 27% sometimes); 38% of LHTDs perceived their entry-level training inadequate; and 15% did not feel that safety of workers was a high priority with their management. This survey brings to light a number of important safety issues for further research and interventions, e.g., high prevalence of truck crashes, injury underreporting, unrealistically tight delivery schedules

Developing a GPS-based truck freight performance measure platform.

Science.gov (United States)

2010-05-01

Although trucks move the largest volume and value of goods in urban areas, relatively little is known about their travel : patterns and how the roadway network performs for trucks. Global positioning systems (GPS) used by trucking : companies to mana...

Planning for large-scale accidents: learning from the Three Mile Island accident

International Nuclear Information System (INIS)

Fischer, D.W.

1981-01-01

Decision-making issues raised at the Three Mile Island nuclear accident in Pennsylvania are explored. The organizations involved, their interconnections, and decisions are described. The underlying issues bearing on allocation of effort to pre-accident planning and actual accident responses are also noted. Finally, a framework from this effort is used for guiding the planning of operations for future accidents. (author)

Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas

Science.gov (United States)

Tree Biodiesel Truck Transports Capitol Christmas Tree to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Twitter Bookmark Alternative

Truck Thermoacoustic Generator and Chiller

Energy Technology Data Exchange (ETDEWEB)

Keolian, Robert

2011-03-31

This Final Report describes the accomplishments of the US Department of Energy (DOE) cooperative agreement project DE-FC26-04NT42113 - Truck Thermoacoustic Generator and Chiller - whose goal is to design, fabricate and test a thermoacoustic piezoelectric generator and chiller system for use on over-the-road heavy-duty-diesel trucks, driven alternatively by the waste heat of the main diesel engine exhaust or by a burner integrated into the thermoacoustic system. The thermoacoustic system would utilize engine exhaust waste heat to generate electricity and cab air conditioning, and would also function as an auxiliary power unit (APU) for idle reduction. The unit was to be tested in Volvo engine performance and endurance test cells and then integrated onto a Class 8 over-the-road heavy-duty-diesel truck for further testing on the road. The project has been a collaboration of The Pennsylvania State University Applied Research Laboratory, Los Alamos National Laboratory, Clean Power Resources Inc., and Volvo Powertrain (Mack Trucks Inc.). Cost share funding was provided by Applied Research Laboratory, and by Clean Power Resources Inc via its grant from Innovation Works - funding that was derived from the Commonwealth of Pennsylvania. Los Alamos received its funding separately through DOE Field Work Proposal 04EE09.

75 FR 76518 - Volvo Trucks North America and Mack Trucks, Inc., Receipt of Petition for Decision of...

Science.gov (United States)

2010-12-08

... manufactured from March 1, 2007 through December 11, 2009. A total of 1,916 affected Volvo trucks were... trucks were manufactured from March 1, 2007, through December 11, 2009. A total 1,287 affected Mack... that their petition, to exempt them from providing recall notification of noncompliance as required by...

GA-4/GA-9 legal weight truck from reactor spent fuel shipping casks

International Nuclear Information System (INIS)

1990-04-01

The preliminary design report presents the results of General Atomics (GA) preliminary design effort to develop weight truck from reactor spent fuel shipping casks. The thermal evaluation of the Office of Civilian Radioactive Waste Management (OCRWM) cask considered normal and hypothetical accident conditions of transport. We employed analytical modeling as well as fire testing of the neutron shielding material to perform the evaluation. This document addresses the thermal design features of the cask, discusses thermal criteria, and summarizes the results of the thermal evaluation, as well as results of structural containment and nuclear evaluations that support the design. Also included are the results of trade-off studies. 69 refs., 103 figs., 76 tabs

Effects of Variation in Truck Factor on Pavement Performance in Pakistan

Directory of Open Access Journals (Sweden)

Rabia Chaudry

2013-01-01

Full Text Available Seasonal variation coupled with heavy axle loading is the key factor in rapid road deterioration in Pakistan. The serviceability loss is further accelerated by the fact that truck drivers and owners consider overloading as a profitable practice unaware of the adverse effects of this practice. Weigh-in-motion data from two stations located between two major cities of Pakistan (Peshawar and Rawalpindi on Grand Trunk Road (N-5 were collected and analyzed. Analysis of variance and comparison of actual and designed truck factor were performed to identify the most damaging axle truck type. It was found that axle truck type 3 (single/tandem axle is most damaging among all truck types. The actual truck factor for axle truck type 3 is 6.4 times greater than design truck factor. Regression expressions of different forms were also investigated to determine the relationship between truck factor and gross vehicular weight for the specified truck types. An optimum generalization strategy was used to prevent over-generalization and ensure accuracy. For data analysis, 75% of data was used to develop regression models and remaining 25% was to validate those models. The results show that the polynomial expressions performed best and provide a robust relationship that can be employed by the highway authorities to estimate truck factor from gross vehicular weight with a high degree of confidence. It was also observed that damaging effect of various types of trucks was very severe and quite high.

50 CFR 25.72 - Reporting of accidents.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Reporting of accidents. 25.72 Section 25... Reporting of accidents. Accidents involving damage to property, injury to the public or injury to wildlife..., but in no event later than 24 hours after the accident, by the persons involved, to the refuge manager...

Planning and preparing for emergency response to transport accidents involving radioactive material. Safety guide

International Nuclear Information System (INIS)

2005-01-01

The objective of this Safety Guide is to provide guidance to the public authorities and others (including consignors, carriers and emergency response authorities) who are responsible for developing and establishing emergency arrangements for dealing effectively and safely with transport accidents involving radioactive material. It may assist those concerned with establishing the capability to respond to such transport emergencies. It provides guidance for those Member States whose involvement with radioactive material is just beginning. It also provides guidance for those Member States that have already developed their radioactive material industries and the attendant emergency plans but that may need to review and improve these plans

Contributing factors in construction accidents.

Science.gov (United States)

Haslam, R A; Hide, S A; Gibb, A G F; Gyi, D E; Pavitt, T; Atkinson, S; Duff, A R

2005-07-01

This overview paper draws together findings from previous focus group research and studies of 100 individual construction accidents. Pursuing issues raised by the focus groups, the accident studies collected qualitative information on the circumstances of each incident and the causal influences involved. Site based data collection entailed interviews with accident-involved personnel and their supervisor or manager, inspection of the accident location, and review of appropriate documentation. Relevant issues from the site investigations were then followed up with off-site stakeholders, including designers, manufacturers and suppliers. Levels of involvement of key factors in the accidents were: problems arising from workers or the work team (70% of accidents), workplace issues (49%), shortcomings with equipment (including PPE) (56%), problems with suitability and condition of materials (27%), and deficiencies with risk management (84%). Employing an ergonomics systems approach, a model is proposed, indicating the manner in which originating managerial, design and cultural factors shape the circumstances found in the work place, giving rise to the acts and conditions which, in turn, lead to accidents. It is argued that attention to the originating influences will be necessary for sustained improvement in construction safety to be achieved.

Substance use among Iranian drivers involved in fatal road accidents

Directory of Open Access Journals (Sweden)

Shervin eAssari

2014-08-01

Full Text Available Background: Although the problem of substance use among drivers is not limited to a special part of the world, most published epidemiological reports on this topic is from industrial world.Aim: To determine drug use among Iranian adults who were imprisoned for vehicle accidents with fatality. Methods: This study enrolled 51 Iranian adults who were imprisoned for vehicle accidents with fatality. This sample came from a national survey of prisoners. Data was collected at entry to prisons during the last 4 months of 2008 in 7 prisons in different parts of the country. Self reported drug use was registered. Commercial substance use screening tests were also done. Results: Drug test was positive for opioids, cannabis and both in 37.3%, 2.0% and 13.7%, respectively. 29.4% tested positive for benzodiazepines. Using test introduced 23.5% of our sample as drug users, who had declined to report any drug use. Conclusion: Opioids are the most used illicit drug in the case of vehicle accidents with fatality, however, 20% of users do not declare their use. This high rate of drug use in vehicle accidents with fatality reflects the importance of drug use control as a part of injury prevention in Iran. There might be a need for drug screening after severe car accidents.

Feasibility of landfill gas as a liquefied natural gas fuel source for refuse trucks.

Science.gov (United States)

Zietsman, Josias; Bari, Muhammad Ehsanul; Rand, Aaron J; Gokhale, Bhushan; Lord, Dominique; Kumar, Sunil

2008-05-01

The purpose of this paper is to develop a methodology to evaluate the feasibility of using landfill gas (LFG) as a liquefied natural gas (LNG) fuel source for heavy-duty refuse trucks operating on landfills. Using LFG as a vehicle fuel can make the landfills more self-sustaining, reduce their dependence on fossil fuels, and reduce emissions and greenhouse gases. Acrion Technologies Inc. in association with Mack Trucks Inc. developed a technology to generate LNG from LFG using the CO2 WASH process. A successful application of this process was performed at the Eco Complex in Burlington County, PA. During this application two LNG refuse trucks were operated for 600 hr each using LNG produced from gases from the landfill. The methodology developed in this paper can evaluate the feasibility of three LFG options: doing nothing, electricity generation, and producing LNG to fuel refuse trucks. The methodology involved the modeling of several components: LFG generation, energy recovery processes, fleet operations, economic feasibility, and decision-making. The economic feasibility considers factors such as capital, maintenance, operational, and fuel costs, emissions and tax benefits, and the sale of products such as surplus LNG and food-grade carbon dioxide (CO2). Texas was used as a case study. The 96 landfills in Texas were prioritized and 17 landfills were identified that showed potential for converting LFG to LNG for use as a refuse truck fuel. The methodology was applied to a pilot landfill in El Paso, TX. The analysis showed that converting LFG to LNG to fuel refuse trucks proved to be the most feasible option and that the methodology can be applied for any landfill that considers this option.

Luggage truck

NARCIS (Netherlands)

Oosterhuis, E.J.; Luttekes, E.; Rijsenbrij, J.C.

2004-01-01

The present invention relates to a luggage truck (2) comprising a loading space for luggage and provided with a conveyor belt (14) disposed in the loading space for the supply and removal of luggage, which conveyor belt is at the same time a storage unit for the luggage, wherein the conveyor belts

Truck drivers as stakeholders in cooperative driving

NARCIS (Netherlands)

de Bruijn, F.; Terken, J.M.B.; Aarts, E.; de Ruyter, B.; Markopoulos, P.; van Loenen, E.; Wichert, R.; Schouten, B.; Terken, J.M.B.; van Kranenburg, R.; Den Ouden, E.; O'Hare, G.

2014-01-01

Cooperative driving for trucks has been claimed to bring substantial benefits for society and fleet owners because of better throughput and reduced fuel consumption, but benefits for truck drivers are questionable. While most work on cooperative driving focuses on the technology, the current paper

Optimising Shovel-Truck Fuel Consumption using Stochastic ...

African Journals Online (AJOL)

Michael

2017-12-02

Dec 2, 2017 ... J. Bansah. 1University of Mines and Technology, P. O. Box 237, Tarkwa, Ghana. 2Missouri S&T .... of dump trucks which could be mixed fleets or same fleets. .... another portraying the reality of trucks moving from a shovel to a ...

An exploratory study of long-haul truck drivers' secondary tasks and reasons for performing them.

Science.gov (United States)

Iseland, Tobias; Johansson, Emma; Skoog, Siri; Dåderman, Anna M

2018-08-01

Research on drivers has shown how certain visual-manual secondary tasks, unrelated to driving, increase the risk of being involved in crashes. The purpose of the study was to investigate (1) if long-haul truck drivers in Sweden engage in secondary tasks while driving, what tasks are performed and how frequently, (2) the drivers' self-perceived reason/s for performing them, and (3) if psychological factors might reveal reasons for their engaging in secondary tasks. The study comprised 13 long-haul truck drivers and was conducted through observations, interviews, and questionnaires. The drivers performed secondary tasks, such as work environment related "necessities" (e.g., getting food and/or beverages from the refrigerator/bag, eating, drinking, removing a jacket, face rubbing, and adjusting the seat), interacting with a mobile phone/in-truck technology, and doing administrative tasks. The long-haul truck drivers feel bored and use secondary tasks as a coping strategy to alleviate boredom/drowsiness, and for social interaction. The higher number of performed secondary tasks could be explained by lower age, shorter driver experience, less openness to experience, lower honesty-humility, lower perceived stress, lower workload, and by higher health-related quality of life. These explanatory results may serve as a starting point for further studies on large samples to develop a safer and healthier environment for long-haul truck drivers. Copyright © 2018. Published by Elsevier Ltd.

Risk analysis of emergent water pollution accidents based on a Bayesian Network.

Science.gov (United States)

Tang, Caihong; Yi, Yujun; Yang, Zhifeng; Sun, Jie

2016-01-01

To guarantee the security of water quality in water transfer channels, especially in open channels, analysis of potential emergent pollution sources in the water transfer process is critical. It is also indispensable for forewarnings and protection from emergent pollution accidents. Bridges above open channels with large amounts of truck traffic are the main locations where emergent accidents could occur. A Bayesian Network model, which consists of six root nodes and three middle layer nodes, was developed in this paper, and was employed to identify the possibility of potential pollution risk. Dianbei Bridge is reviewed as a typical bridge on an open channel of the Middle Route of the South to North Water Transfer Project where emergent traffic accidents could occur. Risk of water pollutions caused by leakage of pollutants into water is focused in this study. The risk for potential traffic accidents at the Dianbei Bridge implies a risk for water pollution in the canal. Based on survey data, statistical analysis, and domain specialist knowledge, a Bayesian Network model was established. The human factor of emergent accidents has been considered in this model. Additionally, this model has been employed to describe the probability of accidents and the risk level. The sensitive reasons for pollution accidents have been deduced. The case has also been simulated that sensitive factors are in a state of most likely to lead to accidents. Copyright © 2015 Elsevier Ltd. All rights reserved.

Optimising Shovel-Truck Fuel Consumption using Stochastic ...

African Journals Online (AJOL)

Optimising the fuel consumption and truck waiting time can result in significant fuel savings. The paper demonstrates that stochastic simulation is an effective tool for optimising the utilisation of fossil-based fuels in mining and related industries. Keywords: Stochastic, Simulation Modelling, Mining, Optimisation, Shovel-Truck ...

Occupational Accidents And Preventive Measures

CERN Document Server

Fassnacht, V

2006-01-01

This report presents the 2005 statistics concerning occupational accidents involving members of the CERN personnel and contractors' personnel. It sets out the accident frequency and severity rates and provides a breakdown of accidents by cause and injury. It also contains a summary analysis of the most serious accidents and the associated recommendations.

Slow speed object detection for haul trucks

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-09-15

Caterpillar integrates radar technology with its current camera based system. Caterpillar has developed the Integrated Object Detection System, a slow speed object detection system for mining haul trucks. Object detection is a system that aids the truck operator's awareness of their surroundings. The system consists of a color touch screen display along with medium- and short-range radar as well as cameras, harnesses and mounting hardware. It is integrated into the truck's Work Area Vision System (WAVS). After field testing in 2007, system commercialization began in 2008. Prototype systems are in operation in Australia, Utah and Arizona and the Integrated Object Detection System will be available in the fourth quarter of 2009 and on production trucks 785C, 789C, 793D and 797B. The article is adapted from a presentation by Mark Richards of Caterpillar to the Haulage & Loading 2009 conference, May, held in Phoenix, AZ. 1 fig., 5 photos.

The association between adolescent entry into the trucking industry and risk of HIV among long-distance truck drivers in India.

Science.gov (United States)

Mishra, Ram Manohar; Dube, Madhulika; Saggurti, Niranjan; Pandey, Arvind; Mahapatra, Bidhubhusan; Ramesh, Sowmya

2012-01-01

This study examines the relationship between entry into the trucking industry during adolescence and both sexually transmitted infections (STIs) and infection by the human immunodeficiency virus (HIV) among long-distance truck drivers in India. Data were sourced from a cross-sectional survey (sample size: 2066) undertaken in 2007 among long-distance truck drivers. The survey spread across major transshipment locations covering the bulk of India's transport volume along four routes. Participants were interviewed about sexual behaviors and were tested for HIV and STIs. The present authors constructed two synthetic cohorts based on the participants' duration of employment in the trucking industry: (1) low (duration ≤ 6 years) and (2) high experience (duration ≥ 7 years). Based on age at entry into the trucking industry, participants were termed as either adolescent (age at entry 4.0%, respectively; adjusted OR: 1.9; 95% CI: 1.2-3.1) and syphilis (5.7% versus 3.5%, respectively; adjusted OR: 1.8; 95% CI: 1.1-3.1). These results suggest the need for focused behavioral change programs in HIV prevention interventions for adolescent truckers in India and elsewhere.

Truck drivers' opinion on road safety in Tanzania--a questionnaire study.

Science.gov (United States)

Kircher, Katja; Andersson, Jan

2013-01-01

Even though the traffic fatality risk (fatalities per 100,000 inhabitants) in Tanzania is quite low, the fatality rate (fatalities per 10,000 vehicles) is one of the highest in the world. With increasing vehicle density this means that the number of people dying in traffic will increase dramatically in the near future. Therefore, it is important to implement measures to increase traffic safety as soon as possible, and in order to be able to do this in an efficient way, it is important to investigate where the main problems lie. Within the European Union (EU) project ASSET-Road a questionnaire study on road safety was conducted with 250 truck drivers in Tanzania. The study was done to increase the knowledge about the situation of the Tanzanian truckers, who are the most frequent road users in the country. The drivers were interviewed in 3 different towns in southern Tanzania, and participation was voluntary. The questionnaire treated demographics, the state of the drivers' vehicles, the frequency of breakdowns, and the maintenance of the vehicles. Further questions concerned driver behavior, crash involvement, crash risk, and crash mitigation. The drivers who participated in the study were predominantly male and their average age was 36 years. Truck drivers reported driving 10.6 h without a break on average, with several drivers reporting that they had to drive 24 h without rest. Around 40 percent of the trucks did not have any seat belts installed, with a larger share of older trucks lacking belts. Most of the drivers who had seat belts reported using them, however. Almost 40 percent of the drivers reported being involved in at least one crash, and 45 percent of those drivers had experienced fatal crashes. This underlines that the crash frequency per vehicle is very high, and the results are often severe, especially when heavy vehicles are involved. When asked what the 3 most common crash causations were, driver-related causes were named frequently. Drivers were

Projection of light-truck population to year 2025

Energy Technology Data Exchange (ETDEWEB)

1978-10-01

The recent growth in the number of light trucks is a matter of considerable interest in that it may have far-reaching implications for gasoline consumption. This paper forecasts the number of light trucks in the years to 2025. The forecast is based on economic scenarios developed by SRI International. Except for the case of the most-dismal economic forecast, the number of light trucks is predicted to increase monotonically and to show the greatest rate of increase between 1973 and 1980.

Exhaust Fine Particle and Nitrogen Oxide Emissions from Individual Heavy-Duty Trucks at the Port of Oakland

Science.gov (United States)

Dallmann, T. R.; Harley, R. A.; Kirchstetter, T.

2010-12-01

Heavy-duty (HD) diesel trucks are a source of nitrogen oxide (NOx) emissions as well as primary fine particulate matter (PM2.5) that includes black carbon (BC) as a major component. Heavy-duty trucks contribute significantly to elevated levels of diesel particulate matter found near highways and in communities surrounding major freight-handling facilities. To reduce the air quality impact of diesel engine emissions, the California Air Resources Board has adopted new rules requiring the retrofit or replacement of in-use HD trucks. These rules take effect during 2010 at ports and railyards, and apply to all trucks operating in California by 2014. This study involves on-road measurements of PM2.5, BC, and NOx emission factor distributions from individual HD trucks driving into the Port of Oakland in the San Francisco Bay area. Measurements of exhaust plumes from individual trucks were made using a mobile laboratory equipped with fast time response (1 Hz) PM2.5, BC, NOx, and carbon dioxide (CO2) sensors. The mobile laboratory was stationed on an overpass above an arterial roadway that connects the Port to a nearby highway (I-880). The air sampling inlet was thereby located above the vertical exhaust pipes of HD diesel trucks passing by on the arterial roadway below. Fuel-specific PM2.5, BC, and NOx emission factors for individual trucks were calculated using a carbon balance method in which concentrations of these species in an exhaust plume are normalized to CO2 concentrations. Initial field sampling was conducted in November, 2009 prior to the implementation of new emission rules. Additional emission measurements were made at the same location during June 2010 and emission factor distributions and averages will be compared.

Major Accidents (Gray Swans) Likelihood Modeling Using Accident Precursors and Approximate Reasoning.

Science.gov (United States)

Khakzad, Nima; Khan, Faisal; Amyotte, Paul

2015-07-01

Compared to the remarkable progress in risk analysis of normal accidents, the risk analysis of major accidents has not been so well-established, partly due to the complexity of such accidents and partly due to low probabilities involved. The issue of low probabilities normally arises from the scarcity of major accidents' relevant data since such accidents are few and far between. In this work, knowing that major accidents are frequently preceded by accident precursors, a novel precursor-based methodology has been developed for likelihood modeling of major accidents in critical infrastructures based on a unique combination of accident precursor data, information theory, and approximate reasoning. For this purpose, we have introduced an innovative application of information analysis to identify the most informative near accident of a major accident. The observed data of the near accident were then used to establish predictive scenarios to foresee the occurrence of the major accident. We verified the methodology using offshore blowouts in the Gulf of Mexico, and then demonstrated its application to dam breaches in the United Sates. © 2015 Society for Risk Analysis.

Real-time pedestrian detection in a Truck's blind spot camera

OpenAIRE

Van Beeck, Kristof; Goedemé, Toon

2014-01-01

In this paper we present a multi-pedestrian detection and tracking framework targeting a specific application: detecting vulnerable road users in a truck's blind spot zone. Research indicates that existing non-vision based safety solutions are not able to handle this problem completely. Therefore we aim to develop an active safety system which warns the truck driver if pedestrians are present in the truck's blind spot zone. Our system solely uses the vision input from the truck's blind spot c...

Adaptive Virtual Tow Bar and Transition of Control : A truck driving simulator study

NARCIS (Netherlands)

Wilschut, E.S.; Willemsen, D.M.C.; Hogema, J.H.; Martens, M.H.

2016-01-01

Background : Truck platooning, with trucks being virtually connected, is getting more and more attention. Truck platooning offers the potential for substantial fuel savings while allowing the truck driver in the platoon to take a rest. However, at the current state of technology, truck drivers are

28 CFR 301.106 - Repetitious accidents.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Repetitious accidents. 301.106 Section 301.106 Judicial Administration FEDERAL PRISON INDUSTRIES, INC., DEPARTMENT OF JUSTICE INMATE ACCIDENT COMPENSATION General § 301.106 Repetitious accidents. If an inmate worker is involved in successive accidents...

Development of Diesel Engine Operated Forklift Truck for Explosive Gas Atmospheres

Science.gov (United States)

Vishwakarma, Rajendra Kumar; Singh, Arvind Kumar; Ahirwal, Bhagirath; Sinha, Amalendu

2018-02-01

For the present study, a prototype diesel engine operated Forklift truck of 2 t capacity is developed for explosive gas atmosphere. The parts of the Forklift truck are assessed against risk of ignition of the explosive gases, vapors or mist grouped in Gr. IIA and having ignition temperature more than 200°C. Identification of possible sources of ignition and their control or prevention is the main objective of this work. The design transformation of a standard Forklift truck into a special Forklift truck is made on prototype basis. The safety parameters of the improved Forklift truck are discussed in this paper. The specially designed Forklift truck is useful in industries where explosive atmospheres may present during normal working conditions and risk of explosion is a concern during handling or transportation of materials. This indigenous diesel engine based Forklift truck for explosive gas atmosphere classified as Zone 1 and Zone 2 area and gas group IIA is developed first time in India in association with the Industry.

Demonstration of fleet trucks fueled with PV hydrogen

International Nuclear Information System (INIS)

Provenzano, J.; Scott, P.B.; Zweig, R.

1998-01-01

The Clean Air Now (CAN) Solar Hydrogen Project has been installed at the Xerox Corporation, El Segundo, California site. Three Ford Ranger trucks have been converted to use hydrogen fuel. The ''stand- alone'' electrolyzer and hydrogen dispensing system is powered by a photovoltaic array with no connection to the power grid. A variable frequency DC/AC converter steps up the voltage to drive the 15 hp motor for the hydrogen compressor. Up to 400 standard cubic meters (SCM) of solar hydrogen is stored, and storage of up to 2300 SCM of commercial hydrogen is collocated. As the hydrogen storage is within 5km of Los Angeles International Airport, pilot operation of a hydrogen fuel cell bus for airport shuttle service has been demonstrated with fueling at the CAN facility. The truck engine conversions are bored to 2.91 displacement, use a Roots type supercharger and CVI (constant volume injection) fuel induction to allow performance similar to that of the gasoline powered truck. Truck fuel storage is done with carbon composite tanks at pressures up to 24.8 MPa (3600 psi). Two tanks are located just behind the driver's cab, and take up nearly half of the truck bed space. The truck highway range is approximately 140 miles. The engine operates in lean burn mode, with nil emissions of CO and HC. NO x emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two Xerox fleet trucks have been converted, and one for the City of West Hollywood. The Clean Air Now Program demonstrates that hydrogen powered fleet development is an appropriate safe, and effective strategy for improvement of urban air quality. It further demonstrates that continued technological development and cost reduction will make such implementation competitive. (Author)

Adaptation of topology optimization on truck-structure; Kinshitsukaho ni yoru iso saitekika shuho no truck kozo eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Tachibana, H; Kojima, A; Chiba, S [Mitsubishi Motors Corp., Tokyo (Japan)

1997-10-01

An optimization using the homogenization method has been applied to a truck-structure on the concept design stage. A truck-structure is grouped into 3 classes (thin plate structure , thick plate structure and solid structure), then example, effectiveness and method for the application for the purpose of weight reduction , high rigidity and high eigen-frequency are introduced. 3 refs., 24 figs., 1 tab.

Sleep quality in long haul truck drivers: A study on Iranian national data.

Science.gov (United States)

Sadeghniiat-Haghighi, Khosro; Yazdi, Zohreh; Kazemifar, Amir-Mohammad

2016-08-01

Iran has a high rate of road traffic accidents. Poor quality of sleep brings about loss of attention, which is an important cause of road traffic accidents particularly in monotonous roads. The causes of poor quality of sleep in occupational drivers are multifactorial. The objective of the present study was to assess the prevalence of poor sleep quality among occupational drivers with rotating work schedules and analyze its different risk factors. 2200 professional long-haul truck drivers who had been referred to the Occupational Health Clinic for routine education course were invited. We obtained data from eight provinces from various parts of Iran during 2012-2013. Data were collected using a questionnaire including questions about demographic and job characteristics. Pittsburg Sleep Quality Index (PSQI) was used to assess drivers' sleep quality. Mean working (driving) time was (9.3±2.5) hours daily and (55.5 ± 18.29) hours weekly. About 23.5% of the drivers reported history of smoking, 14.5% had low job satisfaction and 60% had irregular work schedule. 16.4% of drivers had an accidents leading to injury during the past five years. The mean PSQI score was 4.2 ± 2.7; 54% had a PSQI>5 (poor quality of sleep). Multivariate logistic regression showed that smoking, job satisfaction, history of accidents, shift work and work hours per day were the most important risk factors for poor sleep quality. Results obtained from the current study showed a high prevalence of poor quality of sleep among professional drivers. It warrants more attention to this significant problem using some measures to improve working conditions in professional drivers, as well as health promotion interventions.

CUSTOMER'S PERCEPTION TOWARDS FOOD TRUCK PRODUCTS IN INDIA

OpenAIRE

Dr. Ramakrishna Bandaru*, Prof. H. Venkateshwarlu

2017-01-01

Food Truck business is a very famous and a growing business in today’s time. Over the decade, every country in the world has been following the trend of the mobile food business. The silent feature of the food truck business is ‘customer reach and satisfaction’. Along with the increase in people living standards, ‘food on wheel’ business made a popular. According to IBIS World report, the food truck industry in the world has grown an average of 9.3% per year over the last five years. Slowly,...

Experimental Measurement of the Flow Field of Heavy Trucks

Energy Technology Data Exchange (ETDEWEB)

Fred Browand; Charles Radovich

2005-05-31

Flat flaps that enclose the trailer base on the sides and top are known to reduce truck drag and reduce fuel consumption. Such flapped-truck geometries have been studied in laboratory wind tunnels and in field tests. A recent review of wind tunnel data for a variety of truck geometries and flow Reynolds numbers show roughly similar values of peak drag reduction, but differ in the determination of the optimum flap angle. Optimum angles lie in the range 12 degrees-20 degrees, and may be sensitive to Reynolds number and truck geometry. The present field test is undertaken to provide additional estimates of the magnitude of the savings to be expected on a typical truck for five flap angles 10, 13, 16, 19, and 22 degrees. The flaps are constructed from a fiberglass-epoxy-matrix material and are one-quarter of the base width in length (about 61 cm, or 2 feet). They are attached along the rear door hinge lines on either side of the trailer, so that no gap appears at the joint between the flap and the side of the trailer The flap angle is adjusted by means of two aluminum supports. The present test is performed on the NASA Crows Landing Flight Facility at the northern end of the San Joaquin valley in California. The main runway is approximately 2400 meters in length, and is aligned approximately in a north-south direction The test procedure is to make a series of runs starting at either end of the runway. All runs are initiated under computer control to accelerate the truck to a target speed of 60 mph (96 6 km/hr), to proceed at the target speed for a fixed distance, and to decelerate at the far end of the runway. During a run, the broadcast fuel rate, the engine rpm, forward speed, elapsed time--as well as several other parameters (10 in all)--are digitized at a rate of 100 digitizations per second. Various flapped-conditions are interspersed with the ''no flaps'' control, and are sequenced in a different order on different days. Approximately 310 runs

Increased traffic accident rates associated with shale gas drilling in Pennsylvania.

Science.gov (United States)

Graham, Jove; Irving, Jennifer; Tang, Xiaoqin; Sellers, Stephen; Crisp, Joshua; Horwitz, Daniel; Muehlenbachs, Lucija; Krupnick, Alan; Carey, David

2015-01-01

We examined the association between shale gas drilling and motor vehicle accident rates in Pennsylvania. Using publicly available data on all reported vehicle crashes in Pennsylvania, we compared accident rates in counties with and without shale gas drilling, in periods with and without intermittent drilling (using data from 2005 to 2012). Counties with drilling were matched to non-drilling counties with similar population and traffic in the pre-drilling period. Heavily drilled counties in the north experienced 15-23% higher vehicle crash rates in 2010-2012 and 61-65% higher heavy truck crash rates in 2011-2012 than control counties. We estimated 5-23% increases in crash rates when comparing months with drilling and months without, but did not find significant effects on fatalities and major injury crashes. Heavily drilled counties in the southwest showed 45-47% higher rates of fatal and major injury crashes in 2012 than control counties, but monthly comparisons of drilling activity showed no significant differences associated with drilling. Vehicle accidents have measurably increased in conjunction with shale gas drilling. Copyright © 2014. Published by Elsevier Ltd.

Air transport pilot involvement in general aviation accidents

Science.gov (United States)

1986-01-01

General aviation (GA) fatal accident records of airport transport pilots (ATPs) : were : compared to those of private pilots (PVTs). : ATPs are safer GA pilots than the PVTs. : They have comparable exposure in GA airplanes and account for 7.5% of all...

Model based development of cruise control for Mercedes-Benz trucks; Modellbasierte Entwicklung eines Tempomat fuer Mercedes-Benz Trucks

Energy Technology Data Exchange (ETDEWEB)

Wuensche, M. [VDI, Berlin (Germany); Elser, J.; Dorner, J. [DaimlerChrysler AG, Stuttgart (Germany); Wahner, U.; Kanamueller, B. [MathWorks GmbH, Muenchen (Germany)

2005-07-01

It was necessary to reengineer the cruise control of Mercedes-Benz Trucks for its world wide use in commercial vehicles of the DaimlerChrysler AG. For this extensive task a new software development process of model based function development and automatic serial code generation was installed and exemplary used. Key aspects of this process are the involvement of software-in-the-loop and hardware-in-the-loop simulation technologies to ensure a high software quality through the whole cycle. The simulation and modeling tool chain consists of Matlab, Simulink and Embedded Coder, therefore the project was realized under assistance of the consulting department of The MathWorks Inc. (orig.)

Reactor safety study. An assessment of accident risks in U.S. commercial nuclear power plants. Appendix I. Accident definition and use of event trees

International Nuclear Information System (INIS)

1975-10-01

Information is presented concerning accident definition and use of event trees, event tree methodology, potential accidents covered by the reactor safety study, analysis of potential accidents involving the reactor core, and analysis of potential accidents not involving the core

Raman detection of hydrohalite formation: Avoiding accidents on icy roads by deicing where salt will not work

DEFF Research Database (Denmark)

Berg, Rolf W.

2017-01-01

salt deicing trucks may be equipped with “artificial intelligence” based on a duel deicing system that switches between normal NaCl deicing and non-NaCl deicing based on Raman spectroscopy. The advantages are first of all less traffic accidents and lower environmental impact and corrosion from Na......Cl, but disadvantages are increased costs of investments and consumption of non-NaCl deicing agents....

Report on a radiotherapy underdose accident

Energy Technology Data Exchange (ETDEWEB)

Christodoulides, G; Christofides, S [Medical Physics Department, Nicosia General Hospital, 1450 Nicosia (Cyprus)

1999-12-31

Reporting information on accidents and incidents involving radiation sources provides a body of knowledge which can help to prevent accidents of a similar nature. Accident information has to be made available to users, manufacturers and regulators; An international effort to pool and analyse incident and accident information will provide more complete and reliable indicators of root causes and trends and recommendations for future accident avoidance. An accident due to human error involving a superficial x-ray therapy machine and patients treated for postoperative breast cancer is reported here. 43 women receiving radiotherapy treatment have received significantly less radiation dose than the prescribed dose. The worst dose percentage within the radiation field was 20% of the prescribed dose. The worst dose percentage on the operation scar of the breast was 52% of the prescribed radiation dose. The response to accidents/incidents in radiotherapy is discussed. (authors) 4 refs., 5 figs., 1 tabs.

Analysis of major trends in U.S. commercial trucking, 1977-2002.

Energy Technology Data Exchange (ETDEWEB)

Bertram, K. M.; Santini, D .J.; Vyas, A. D.

2009-06-10

This report focuses on various major long-range (1977-2002) and intermediate-range (1982-2002) U.S. commercial trucking trends. The primary sources of data for this period were the U.S. Bureau of the Census Vehicle Inventory and Use Survey and Truck Inventory and Use Survey. In addition, selected 1977-2002 data from the U.S. Department of Energy/Energy Information Administration and from the U.S. Department of Transportation/Federal Highway Administration's Highway Statistics were used. The report analyzes (1) overall gasoline and diesel fuel consumption patterns by passenger vehicles and trucks and (2) the population changes and fuels used by all commercial truck classes by selected truck type (single unit or combination), during specified time periods, with cargo-hauling commercial trucks given special emphasis. It also assesses trends in selected vehicle miles traveled, gallons per vehicle miles traveled, and gallons per cargo ton-mile traveled, as well as the effect of cargo tons per truck on fuel consumption. In addition, the report examines long-range trends for related factors (e.g., long-haul mileages driven by heavy trucks) and their impacts on reducing fuel consumption per cargo-ton-mile and the relative shares of total commercial fuel use among truck classes. It identifies the effects of these trends on U.S. petroleum consumption. The report also discusses basic engineering design and performance, national legislation on interstate highway construction, national demographic trends (e.g., suburbanization), and changes in U.S. corporate operations requirements, and it highlights their impacts on both the long-distance hauling and shorter-distance urban and suburban delivery markets of the commercial trucking industry.

Decision diagram for neutron and photon dose estimation and for classification of persons involved in radiation accident

International Nuclear Information System (INIS)

Anon.

1981-01-01

The relation is described between monitoring and health care measures taken during a radiation accident. The decision-making chart for the assessment of exposure and the classification of people involved are presented, the risks of the respective decision-making are discussed and the flow charts and explanations for the diagrams are given. (H.S.)

Analysis of Maintenance Service Contracts for Dump Trucks Used in Mining Industry with Simulation Approach

Science.gov (United States)

Dymasius, A.; Wangsaputra, R.; Iskandar, B. P.

2016-02-01

A mining company needs high availability of dump trucks used to haul mining materials. As a result, an effective maintenance action is required to keep the dump trucks in a good condition and hence reducing failure and downtime of the dump trucks. To carry out maintenance in-house requires a high intensive maintenance facility and high skilled maintenance specialists. Often, outsourcing maintenance is an economic option for the company. An external agent takes a proactive action with offering some maintenance contract options to the owner. The decision problem for the owner is to decide the best option and for the agent is to determine the optimal price for each option offered. A non-cooperative game-theory is used to formulate the decision problems for the owner and the agent. We consider that failure pattern of each truck follows a non-homogeneous Poisson process (NHPP) and a queueing theory with multiple servers is used to estimate the downtime. As it involves high complexity to model downtime using a queueing theory, then in this paper we use a simulation method. Furthermore, we conduct experiment to seek for the best number of maintenance facilities (servers) which minimises maintenance and penalty costs incurred to the agent.

Assessment of the radiological risks of road transport accidents involving type A package shipments

International Nuclear Information System (INIS)

Lange, F.; Fett, H.J.; Schwarz, G.; Raffestin, D.; Schneider, T.; Gelder, R.; Hughes, J.S.; Shaw, K.B.; Hedberg, B.; Simenstad, P.; Svahn, B.; Hienen, J.F.A.; Jansma, R.

1998-01-01

This paper is an account of work performed within a multi-lateral research project on the radiological risks associated with the transportation of Type A packaged radioactive material. The research project has been performed on behalf of the European Commission and various national agencies of the participating countries and involved organizations and institutes of five EU Member States, France, Germany, The Netherlands, Sweden, and the UK. The main objectives of the research project were the assessment and appraisal of the potential radiological risks of road transport accidents involving Type A package shipments in participating EU Member States. Data were collected and include harmonized sets information related to the type, quantity and characteristics of Type A package shipments by road. Such databases were basically non-existent until recently. The results are expected to be valuable to both national agencies and international organizations, with responsibilities for the safe transport of radioactive materials by providing some insight in the carriage of radioactive materials by road making up a major fraction of radioactive material transports. Similarly, a wide body of information has been collected and compiled on road transport accidents in terms of the frequency of occurrence and the severity of accidental impact loads potentially experienced by a Type A package.In addition, the results will facilitate judgement of the adequacy of the IAEA Transport Regulations as far as Type A packages are concerned. (O.M.)

Contents of management plans for incidents and accidents involving the transport of radioactive substances. Guide no. 17, Version of 22/12/2014

International Nuclear Information System (INIS)

2014-01-01

This guide presents the essential topics to be developed in a management plan for incidents and accidents involving the transport of radioactive substances for civil use. It does not aim to be exhaustive and could be added to by each party involved in the transport, who can make the necessary adaptations and additions, taking account of the particularities of its shipments and its organisation, as well as those of the company or group to which it belongs. The radioactive substances transport incident and accident management plan is a document comprising a descriptive part and an operational part. It presents the overall response of the party involved in the transport operation to an incident or accident situation concerning one of its shipments and the steps it intends to make in order to support the authorities in charge of this situation, in the best possible conditions. This response is designed to cover the cases of incidents or accidents whether or not they lead to a radiological emergency situation. The guide exclusively concerns: - road transport; - rail transport; - the 'road' and 'rail' parts of multimodal transport operations. The case of an incident or an accident occurring during a particular stop such as a transit site, in a transhipment area (port, airport, railway station, etc.), or in a transport infrastructure, is also covered by the radioactive substances transport incident and accident management plan, which then supports the entities in charge of managing this situation (operator of the transhipment area or the transport infrastructure and - as applicable - their supervisory authorities). The level of risk associated with transport incidents and accidents varies widely, according to the nature and quantities of the materials being carried, the number of shipments made and the package model used. The incident and accident management plan must therefore be tailored to the specific nature of the shipments by the party concerned. The radioactive

Electric urban delivery trucks: energy use, greenhouse gas emissions, and cost-effectiveness.

Science.gov (United States)

Lee, Dong-Yeon; Thomas, Valerie M; Brown, Marilyn A

2013-07-16

We compare electric and diesel urban delivery trucks in terms of life-cycle energy consumption, greenhouse gas (GHG) emissions, and total cost of ownership (TCO). The relative benefits of electric trucks depend heavily on vehicle efficiency associated with drive cycle, diesel fuel price, travel demand, electric drive battery replacement and price, electricity generation and transmission efficiency, electric truck recharging infrastructure, and purchase price. For a drive cycle with frequent stops and low average speed such as the New York City Cycle (NYCC), electric trucks emit 42-61% less GHGs and consume 32-54% less energy than diesel trucks, depending upon vehicle efficiency cases. Over an array of possible conditions, the median TCO of electric trucks is 22% less than that of diesel trucks on the NYCC. For a drive cycle with less frequent stops and high average speed such as the City-Suburban Heavy Vehicle Cycle (CSHVC), electric trucks emit 19-43% less GHGs and consume 5-34% less energy, but cost 1% more than diesel counterparts. Considering current and projected U.S. regional electricity generation mixes, for the baseline case, the energy use and GHG emissions ratios of electric to diesel trucks range from 48 to 82% and 25 to 89%, respectively.

Truck Drivers' Use of the Internet: A Mobile Health Lifeline.

Science.gov (United States)

Heaton, Karen; Combs, Bryan; Griffin, Russell

2017-06-01

Because of their social isolation, irregular and unpredictable schedules, limited access to health care, and long periods of travel, long-haul truckers may benefit from the use of mobile health applications on Internet-capable devices. The purpose of this study was to determine Internet access and usage among a sample of long-haul truck drivers. In this cross-sectional study, truck drivers completed a pencil and paper survey with questions on demographics, work and health histories, and Internet access and usage for both personal and job reasons. A total of 106 truck drivers were recruited from trucking industry trade shows, by word of mouth, and directly from trucking companies. Overall, the truck drivers' use of the Internet was limited. Their usage for personal and job-related reasons differed. Social connectivity and access to health and wellness information were important during personal usage time. Job-related Internet use was highly practical, and applied to seeking information for directions and maps, fuel stops and pricing, and communicating with employers or transmitting documents. Age and experience were associated with Internet use. Younger, less-experienced drivers used the Internet more than older, experienced drivers. Targeted mobile health messaging may be a useful tool to inform truck drivers of health conditions and plans, and may provide links to primary care providers needing to monitor or notify drivers of diagnostic results or treatment plans.

The design and implementation of a garbage truck fleet management system

Directory of Open Access Journals (Sweden)

Chen, C. H.

2016-05-01

Full Text Available In recent years, the improvement of cloud computing and mobile computing techniques has led to the availability of a variety of mobile applications (‘apps’ in the app store. For instance, a garbage truck app that can provide the immediate location of a garbage truck, the location of collection points, and forecasted arrival times of garbage trucks would be useful for mobile users. Since the power consumption of apps on mobile devices if of concern to mobile users, an optimised power-saving mechanism for updating messages, which is based on location information, for a proposed garbage truck fleet management system (GTFMS is proposed and implemented in this paper. The GTFMS is a three- component system that includes the on-board units on garbage trucks, a fleet management system, and a garbage truck app. In this study, an arrival time forecasting method is designed and implemented in the fleet management system, so that the garbage truck app can retrieve the forecasted arrival time via web services. A message updating event is then triggered that reports the location of garbage truck and the forecasted arrival time. In experiments conducted on case studies, the results showed that the mean accuracy of predicted arrival time by the proposed method is about 81.45 per cent. As for power consumption, the cost of traditional mobile apps is 2,880 times that of the mechanism proposed in this study. Consequently, the GTFMS can provide the precise forecasted arrival time of garbage trucks to mobile users, while consuming less power.

Prevalence and correlates of poor sleep quality and daytime sleepiness in Belgian truck drivers.

Science.gov (United States)

Braeckman, Lutgart; Verpraet, Rini; Van Risseghem, Marleen; Pevernagie, Dirk; De Bacquer, Dirk

2011-03-01

Sleepiness and sleep complaints are common among professional drivers. Sleepiness is a considerable problem not only because it affects the drivers' well-being, but also because of the consequences for performance and safety. Assessment of the (self-reported) prevalence and research into the risk factors are thus an important health issue and are also indispensable to prevent productivity loss and work-related accidents and injuries. Therefore, the aim of this study was to describe sleeping, driving, and health characteristics of Belgian truck drivers and to determine occupational and individual factors associated with poor sleep quality and daytime sleepiness. Cross-sectional data were collected using a self-administered questionnaire that included the Pittsburgh Sleep Quality Index (PSQI), Epworth Sleepiness Scale (ESS), and Berlin Questionnaire (BQ). The mean (SD) age of the 476 studied truck drivers was 42.7 (10.2) yrs and the mean (SD) body mass index was 27.3 (5.1) kg/m(2). Approximately 47% declared that they drove >50 h/wk and found their work schedule unrealistic. The mean (SD) PSQI score was 4.45 (2.7); poor quality of sleep (PSQI >5) was found in 27.2%. The mean (SD) ESS score was 6.79 (4.17); 18% had a score >10. The BQ indicated that 21.5% had a higher risk on obstructive sleep apnea. In multiple logistic regression analysis, low educational level (odds ratio [OR] 1.86), current smoking (OR 1.75), unrealistic work schedule (OR 1.75), and risk for obstructive sleep apnea (OR 2.97) were found to be independent correlates of daytime sleepiness. Poor sleep quality was significantly associated with poor self-perceived health (OR 1.95), unrealistic work schedule (OR 2.85), low job satisfaction (OR 1.91), and less driving experience (OR 1.73). These results show that poor sleep quality and daytime sleepiness were prevalent in Belgian truck drivers. Taking into account that several significant correlates with respect to these sleep problems were identified

Evaluation of an exhaust gas evacuation system during propane-fueled lift truck maintenance

International Nuclear Information System (INIS)

Roberge, B.; Beaudet, Y.; Lazure, L.; Menard, L.; Turcotte, A.

2006-01-01

Exposure to carbon monoxide (CO) gas in the workplace can cause health problem. CO gas is colourless and odourless, and exposure to it can cause intoxication, particularly for mechanics working on internal combustion engines fed by propane-fueled lift trucks. Regular procedures for evacuating the gases emitted during routine mechanical repairs involve the use of rigid evacuating pipes attached to the building and hooked to a flexible pipe at the end of the exhaust pipe. With lift trucks, this procedure is limited because of the configuration of these vehicles, and also because this type of work is often done in places without access to permanent mechanical ventilation. The object of this study was to propose a new evacuation method for CO gas fumes that would lower the exposures of fumes for mechanics and for workstations. It identified the criteria that should be considered, such as the configuration of the existing exhaust system of lift trucks, and feasibility of using this system at a variety of on-site locations. The design of the device was described and evaluated. 7 refs., 6 tabs., 8 figs., 3 appendices

Development of Auto-Stacking Warehouse Truck

Directory of Open Access Journals (Sweden)

Kuo-Hsien Hsia

2018-03-01

Full Text Available Warehouse automation is a very important issue for the promotion of traditional industries. For the production of larger and stackable products, it is usually necessary to operate a fork-lifter for the stacking and storage of the products by a skilled person. The general autonomous warehouse-truck does not have the ability of stacking objects. In this paper, we develop a prototype of auto-stacking warehouse-truck that can work without direct operation by a skill person. With command made by an RFID card, the stacker truck can take the packaged product to the warehouse on the prior-planned route and store it in a stacking way in the designated storage area, or deliver the product to the shipping area or into the container from the storage area. It can significantly reduce the manpower requirements of the skilled-person of forklift technician and improve the safety of the warehousing area.

Facial trauma among victims of terrestrial transport accidents.

Science.gov (United States)

d'Avila, Sérgio; Barbosa, Kevan Guilherme Nóbrega; Bernardino, Ítalo de Macedo; da Nóbrega, Lorena Marques; Bento, Patrícia Meira; E Ferreira, Efigênia Ferreira

2016-01-01

In developing countries, terrestrial transport accidents - TTA, especially those involving automobiles and motorcycles - are a major cause of facial trauma, surpassing urban violence. This cross-sectional census study attempted to determine facial trauma occurrence with terrestrial transport accidents etiology, involving cars, motorcycles, or accidents with pedestrians in the northeastern region of Brazil, and examine victims' socio-demographic characteristics. Morbidity data from forensic service reports of victims who sought care from January to December 2012 were analyzed. Altogether, 2379 reports were evaluated, of which 673 were related to terrestrial transport accidents and 103 involved facial trauma. Three previously trained and calibrated researchers collected data using a specific form. Facial trauma occurrence rate was 15.3% (n=103). The most affected age group was 20-29 years (48.3%), and more men than women were affected (2.81:1). Motorcycles were involved in the majority of accidents resulting in facial trauma (66.3%). The occurrence of facial trauma in terrestrial transport accident victims tends to affect a greater proportion of young and male subjects, and the most prevalent accidents involve motorcycles. Copyright © 2015 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

49 CFR 215.119 - Defective freight car truck.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Defective freight car truck. 215.119 Section 215... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Freight Car Components Suspension System § 215.119 Defective freight car truck. A railroad may not place or continue in service a...

Aerodynamics Research Revolutionizes Truck Design

Science.gov (United States)

2008-01-01

During the 1970s and 1980s, researchers at Dryden Flight Research Center conducted numerous tests to refine the shape of trucks to reduce aerodynamic drag and improved efficiency. During the 1980s and 1990s, a team based at Langley Research Center explored controlling drag and the flow of air around a moving body. Aeroserve Technologies Ltd., of Ottawa, Canada, with its subsidiary, Airtab LLC, in Loveland, Colorado, applied the research from Dryden and Langley to the development of the Airtab vortex generator. Airtabs create two counter-rotating vortices to reduce wind resistance and aerodynamic drag of trucks, trailers, recreational vehicles, and many other vehicles.

Protective Behaviour of Citizens to Transport Accidents Involving Hazardous Materials: A Discrete Choice Experiment Applied to Populated Areas nearby Waterways.

Directory of Open Access Journals (Sweden)

Esther W de Bekker-Grob

Full Text Available To improve the information for and preparation of citizens at risk to hazardous material transport accidents, a first important step is to determine how different characteristics of hazardous material transport accidents will influence citizens' protective behaviour. However, quantitative studies investigating citizens' protective behaviour in case of hazardous material transport accidents are scarce.A discrete choice experiment was conducted among subjects (19-64 years living in the direct vicinity of a large waterway. Scenarios were described by three transport accident characteristics: odour perception, smoke/vapour perception, and the proportion of people in the environment that were leaving at their own discretion. Subjects were asked to consider each scenario as realistic and to choose the alternative that was most appealing to them: staying, seeking shelter, or escaping. A panel error component model was used to quantify how different transport accident characteristics influenced subjects' protective behaviour.The response was 44% (881/1,994. The predicted probability that a subject would stay ranged from 1% in case of a severe looking accident till 62% in case of a mild looking accident. All three transport accident characteristics proved to influence protective behaviour. Particularly a perception of strong ammonia or mercaptan odours and visible smoke/vapour close to citizens had the strongest positive influence on escaping. In general, 'escaping' was more preferred than 'seeking shelter', although stated preference heterogeneity among subjects for these protective behaviour options was substantial. Males were less willing to seek shelter than females, whereas elderly people were more willing to escape than younger people.Various characteristics of transport accident involving hazardous materials influence subjects' protective behaviour. The preference heterogeneity shows that information needs to be targeted differently depending on

Accidents in making fireworks. Tapaturmat polttopuun teossa

Energy Technology Data Exchange (ETDEWEB)

Solmio, H

1991-01-01

The accidents and the trends in the number of accidents and their causes were analyzed in a study conducted by the Forestry Department of the Work Efficiency Institute. The study was funded by the Finnish Agricultural Enterpreneurs' Pension Fund (MELA). The study material was selected from MELA's accident stage work and cause code. Altogether, the material comprised the following accidents that occurred while making and using firewood: 671 accidents in 1987 and 596 accidents in 1988. The amount of accidents caused by the working environment and hand tools was clearly higher in 1987 than in 1988. The number of accidents occurred while chopping wood was 20 % higher in 1987 than in 1988. April was the most accident-prone month both in 1987 and in 1988. Chopping of firewood was the most dangerous work stage in terms of the number of accidents. In 1988, the number of accidents in chopping firewood was 336, in sawing using circular saw 97 cases and other mechanized chopping led to 93 accidents. Heating with wood caused 33 accidents. In 1988 there were 10 (2 %) accidents involving loss of limbs and 9 of them occurred in the mechanized chopping of firewood. Nine accidents of these involved the loss of one or more fingers. Serious accidents, leading to inability to work for more than 3 months, were most frequent in chopping and in storing firewood.

Criticality accident in Argentina

International Nuclear Information System (INIS)

Oliveira, A.R. de.

1984-01-01

A recent criticality type accident, ocurred in Argetina, is commented. Considerations about the nature of the facility where this accident took place, its genesis, type of operation carried out on the day of the event, and the medical aspects involved are done. (Author) [pt

Design and analysis of truck body for increasing the payload capacity

Science.gov (United States)

Vamshi Krishna, K.; Yugandhar Reddy, K.; Venugopal, K.; Ravi, K.

2017-11-01

Truck industry is a major source of transportation in India. With an average truck travelling about 300 kilometers per day [1], every kilogram of truck weight is of concern to the industry in order to get the best out of the truck. The main objective of this project is to increase the payload capacity of automotive truck body. Every kilogram of increased vehicle weight will decrease the vehicle payload capacity in turn increasing the manufacturing cost and reducing the fuel economy by increase the fuel consumption. With the intension of weight reduction, standard truck body has been designed and analyzed in ANSYS software. C-cross section beams were used instead of conventional rectangular box sections to reduce the weight of the body. Light-weight Aluminum alloy Al 6061 T6 is used to increase the payload capacity. The strength of the Truck platform is monitored in terms of deformation and stress concentration. These parameters will be obtained in structural analysis test condition environment. For reducing the stress concentration the concept of beams of uniform strength is used. Accordingly necessary modifications are done so that the optimized model has a better stress distribution and much lesser weight compared to the conventional model. The results obtained by analyzing the modified model are compared with the standard model.

Solar hydrogen for urban trucks

Energy Technology Data Exchange (ETDEWEB)

Provenzano, J.: Scott, P.B.; Zweig, R. [Clean Air Now, Northridge, CA (United States)

1997-12-31

The Clean Air Now (CAN) Solar Hydrogen Project, located at Xerox Corp., El Segundo, California, includes solar photovoltaic powered hydrogen generation, compression, storage and end use. Three modified Ford Ranger trucks use the hydrogen fuel. The stand-alone electrolyzer and hydrogen dispensing system are solely powered by a photovoltaic array. A variable frequency DC-AC converter steps up the voltage to drive the 15 horsepower compressor motor. On site storage is available for up to 14,000 standard cubic feet (SCF) of solar hydrogen, and up to 80,000 SCF of commercial hydrogen. The project is 3 miles from Los Angeles International airport. The engine conversions are bored to 2.9 liter displacement and are supercharged. Performance is similar to that of the Ranger gasoline powered truck. Fuel is stored in carbon composite tanks (just behind the driver`s cab) at pressures up to 3600 psi. Truck range is 144 miles, given 3600 psi of hydrogen. The engine operates in lean burn mode, with nil CO and HC emissions. NO{sub x} emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two trucks have been converted for the Xerox fleet, and one for the City of West Hollywood. A public outreach program, done in conjunction with the local public schools and the Department of Energy, introduces the local public to the advantages of hydrogen fuel technologies. The Clean Air Now program demonstrates that hydrogen powered fleet development is an appropriate, safe, and effective strategy for improvement of urban air quality, energy security and avoidance of global warming impact. Continued technology development and cost reduction promises to make such implementation market competitive.

UPS CNG Truck Fleet Start Up Experience: Alternative Fuel Truck Evaluation Project

International Nuclear Information System (INIS)

Walkowicz, K.

2001-01-01

UPS operates 140 Freightliner Custom Chassis compressed natural gas (CNG)-powered vehicles with Cummins B5.9G engines. Fifteen are participating in the Alternative Fuel Truck Evaluation Project being funded by DOE's Office of Transportation Technologies and the Office of Heavy Vehicle Technologies

DESIGN OF EXPERIMENTS IN TRUCK COMPANY

Directory of Open Access Journals (Sweden)

Bibiana Kaselyova

2015-07-01

Full Text Available Purpose: Design of experiment (DOE represent very powerful tool for process improvement vastly supported by six sigma methodology. This approach is mostly used by large and manufacturing orientated companies. Presented research is focused on use of DOE in truck company, which is medium size and service orientated. Such study has several purposes. Firstly, detailed description of improvement effort based on DOE can be used as a methodological framework for companies similar to researched one. Secondly, it provides example of successfully implemented low cost design of experiment practise. Moreover, performed experiment identifies key factors, which influence the lifetime of truck tyres.Design/methodology: The research in this paper is based on experiment conducted in Slovakian Truck Company. It provides detailed case study of whole improvement effort, together with problem formulation, design creation and analysis, as well as the results interpretation. The company wants to improve lifetime of the truck tyres. Next to fuel consumption, consumption of tyres and their replacement represent according to them, one of most costly processes in company. Improvement effort was made through the use of PDCA cycle. It start with analysis of current state of tyres consumption. The variability of tyres consumption based on years and types was investigated. Then the causes of tyres replacement were identified and screening DOE was conducted. After a screening design, the full factorial design of experiment was used to identify main drivers of tyres deterioration and breakdowns. Based on result of DOE, the corrective action were propose and implement.Findings: Based on performed experiment our research describes process of tyres use and replacement. It defines main reasons for tyre breakdown and identify main drivers which influence truck tyres lifetime. Moreover it formulates corrective action to prolong tyres lifetime.Originality: The study represents full

The Aggregate Planning For Trucking Operation in Cikarang Dry Port

Directory of Open Access Journals (Sweden)

Dwi Puspita Sari Utami

2015-06-01

Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits. Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

The Aggregate Planning For Trucking Operation in Cikarang Dry Port

Directory of Open Access Journals (Sweden)

Dwi Puspita Sari Utami

2015-07-01

Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits.Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

design and fabrication of a multipurpose railroad hand truck

African Journals Online (AJOL)

user

the guide rail was constructed using 50mm by 50mm mild steel angle bar. The hand truck is ... material handling management, a company's operational performance may ... pose a health risk especially where the hand truck has to be used ...

49 CFR 230.100 - Defects in tender truck axles and journals.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Defects in tender truck axles and journals. 230... Steam Locomotives and Tenders Running Gear § 230.100 Defects in tender truck axles and journals. (a... wheel seats that is more than 1/8 of an inch in depth. (b) Tender truck journal condemning defects...

LASER WELDING WITH MICRO-JET COOLING FOR TRUCK FRAME WELDING

OpenAIRE

Jan PIWNIK; Bożena SZCZUCKA-LASOTA; Tomasz WĘGRZYN; Wojciech MAJEWSKI

2017-01-01

The aim of this paper is to analyse the mechanical properties of the weld steel structure of car body truck frames after laser welding. The best welding conditions involve the use of proper materials and alloy elements in steel and filer materials, in addition to welding technology, state of stress and temperature of exploitation. We present for the first time the properties of steel track structures after laser welding with micro-jet cooling. Therefore, good selection of both welding paramet...

Supplying of Assembly Lines Using Train of Trucks

Science.gov (United States)

Čujan, Zdeněk; Fedorko, Gabriel

2016-11-01

The typical supply system conceptions, i.e. the concepts "Just-in-time" (JIT) and "Just-in-sequence" (JIS) are very important factors with regard to a fluent operation of the assembly lines. Therefore the contemporary intra plant transport systems are being replaced by a new kind of the transportation technology, namely by means of the trains of trucks. The trains of trucks are used in two possible operational modes: either with a driver or without driver (fully automated). The trucks of the logistic trains are also cheaper and they are able to carry a larger volume and mass of the material at once. There are reduced in this way not only the investment costs, but also the operational expenses.

Accidents in family forestry's firewood production.

Science.gov (United States)

Lindroos, Ola; Aspman, Emma Wilhelmson; Lidestav, Gun; Neely, Gregory

2008-05-01

Firewood is commonly used around the world, but little is known about the work involved in its production and associated accidents. The objectives were to identify relationships between accidents and time exposure, workers' age and sex, equipment used and work activities in family forestry's firewood production. Data from a postal survey in Northern Sweden were compared to a database of injuries in the same region. Most accidents occurred to 50-69 year old men, who also worked most hours. No significant differences in sex and age were found between expected and recorded accident frequencies when calculated from total work hours; however, when calculated using numbers of active persons significant differences were found for both age and sex. Frequency of accidents per unit worked time was higher for machine involving activities than for other activities. Accidents that occurred when using wedge splitter machines were responsible for most of this overrepresentation. Fingers were the most commonly injured body parts. Mean accident rate for the equipment used was 87 accidents per million work hours, and the rate was highest for wedge splitters (122 accidents per million work hours). Exposure to elevated risks due to violation of safety procedures is discussed, as well as possible preventative measures.

Sexual behavior among truck drivers.

Science.gov (United States)

Singh, Rajiv Kumar; Joshi, Hari Shankar

2012-01-01

A cross-sectional study was conducted on Lucknow highway in Bareilly district of Uttar Pradesh to study the knowledge of truck drivers about HIV transmission and prevention and to study the sexual behaviour of these drivers with reference to HIV/AIDS. Age, marital status, education, income, drinking alcohol, length of stay away from home, knowledge about transmission and prevention of HIV, and HIV-prone behavior of truck drivers were studied. Chi-square, mean, and SD were calculated. In all, 289 (97.6%) drivers had heard about HIV/AIDS. Only 242 (81.8%) were aware of HIV transmission by heterosexual route. Misconceptions such as HIV transmission by mosquito bites, living in same room, shaking hands, and sharing food were found. Out of 174 (58.8%) who visited Commercial Sex Workers (CSW), 146 (83.9%) used a condom. 38 (12.8%) visited more than 5 CSW in the last 3 months. Time away from home on the road, marital status, alcohol use, and income class were associated with visiting CSW. High-risk behavior was established in the study population. Safe sex and use of condoms need to be promoted among the truck drivers and better condom availability needs to be assured on highways.

Stakeholder involvement facilitates decision making for UK nuclear accident recovery.

Science.gov (United States)

Alexander, C; Burt, R; Nisbet, A F

2005-01-01

The importance of major stakeholders participating in the formulation of strategies for maintaining food safety and agricultural production following a nuclear accident has been successfully demonstrated by the UK 'Agriculture and Food Countermeasures Working Group' (AFCWG). The organisation, membership and terms of reference of the group are described. Details are given of the achievements of the AFCWG and its sub-groups, which include agreeing management options that would be included in a recovery handbook for decision-makers in the UK and tackling the disposal of large volumes of contaminated milk, potentially resulting from a nuclear accident.

Computations for Truck Sliding with TRUCK 3.1 Code

Science.gov (United States)

1989-08-01

16 REFERENCES 1. L u. \\Villiam N.. Hobbs. Norman P. and Atkinson, Michael. TRUCK 3.1-An Improrcd Digital (’oiputtr Program for Calculating the Response...for Operations and Plans ATIN: Technical Libary Director of Chemical & Nuear Operations Dpartnt of the AIW Waskbington, DC 20310 1 Cocaeder US Ay...Lawrenoe Livermore Lab. ATIN: Code 2124, Tedhnical ATTN: Tech Info Dept L-3 Reports Libary P.O. Be 808 Monterey, CA 93940 Livermore, CA 94550 AFSC

Chernobylsk NPP accident and its medical effects

International Nuclear Information System (INIS)

Gus'kova, A.K.

2000-01-01

Medical effects of the Chernobyl accident for various groups of people engaged in liquidation of the accident aftereffects and residents of the regions affected are assessed. Specific medical and social recommendations for each of the five groups of patients are made. Special attention is paid to the health of children who were exposed to external radiation in combination with intake of iodine isotopes. Extremely unfavourable influence of the mass media on the health of people involved in the Chernobyl accident is painted out. The necessity of adequate rehabilitation measures for various categories of patients involved in a large-scale accident is emphasized [ru

Fuel Cell-Powered Lift Truck Fleet Deployment Projects Final Technical Report May 2014

Energy Technology Data Exchange (ETDEWEB)

Klingler, James J [GENCO Infrastructure Solutions, Inc.

2014-05-06

The overall objectives of this project were to evaluate the performance, operability and safety of fork lift trucks powered by fuel cells in large distribution centers. This was accomplished by replacing the batteries in over 350 lift trucks with fuel cells at five distribution centers operated by GENCO. The annual cost savings of lift trucks powered by fuel cell power units was between $2,400 and $5,300 per truck compared to battery powered lift trucks, excluding DOE contributions. The greatest savings were in fueling labor costs where a fuel cell powered lift truck could be fueled in a few minutes per day compared to over an hour for battery powered lift trucks which required removal and replacement of batteries. Lift truck operators where generally very satisfied with the performance of the fuel cell power units, primarily because there was no reduction in power over the duration of a shift as experienced with battery powered lift trucks. The operators also appreciated the fast and easy fueling compared to the effort and potential risk of injury associated with switching heavy batteries in and out of lift trucks. There were no safety issues with the fueling or operation of the fuel cells. Although maintenance costs for the fuel cells were higher than for batteries, these costs are expected to decrease significantly in the next generation of fuel cells, making them even more cost effective.

Preliminary evaluation of the Accident Response Mobile Manipulation System for accident site salvage operations

International Nuclear Information System (INIS)

Trujillo, J.M.; Morse, W.D.; Jones, D.P.

1994-01-01

This paper describes and evaluates operational experiences with the Accident Response Mobile Manipulation System (ARMMS) during simulated accident site salvage operations which might involve nuclear weapons. The ARMMS is based upon a teleoperated mobility platform with two Schilling Titan 7F Manipulators

78 FR 24293 - Pilot Program on NAFTA Trucking Provisions

Science.gov (United States)

2013-04-24

...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... in the Agency's long-haul pilot program to test and demonstrate the ability of Mexico- domiciled... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

A Cognitive Analysis of Truck Drivers’ Right-hand Turns

DEFF Research Database (Denmark)

Sieker, Tobias Grønborg; G. Skulason, Thorgeir; Sletting, Kristian

2015-01-01

This paper presents an investigation of truck drivers’ performance during right-hand turns performed in intersections with traffic lights in order to elicit the truck drivers’ domain, decision-making processes, and the strategies used while executing the turn. To gain knowledge about this, a truc...

Patterns of Harmful Alcohol Consumption among Truck Drivers: Implications for Occupational Health and Work Safety from a Systematic Review and Meta-Analysis

Directory of Open Access Journals (Sweden)

Nicola Luigi Bragazzi

2018-05-01

Full Text Available Alcohol consumption is one of the main causes of productivity losses arising from absenteeism, presenteeism, and workplace injuries. Among occupational categories most affected by the use of this substance, truck drivers are subject to risk factors and risky behaviors that can have a serious impact on their health, their work, and the general road safety. The use of alcohol during truck-driving activities is, indeed, an important risk factor for traffic accidents. The present systematic review and meta-analysis aims at synthesizing the literature regarding harmful alcohol consumption patterns among truck drivers in a rigorous way. A ‘binge drinking’ prevalence of 19.0%, 95% confidence interval or CI (13.1, 26.9 was present. An ‘everyday drinking’ pattern rate of 9.4%, 95% CI (7.0, 12.4 was found, while the rate of alcohol misuse according to the “Alcohol Use Disorders Identification Test” (AUDIT—“Cut down-Annoyed-Guilty-Eye opener questionnaire” (CAGE instruments was computed to be of 22.7%, 95% CI (14.8, 33.0. No evidence of publication bias could be found. However, there is the need to improve the quality of published research, utilizing standardized reliable instruments. The knowledge of these epidemiological data can be useful for decision makers in order to develop, design, and implement ad hoc adequate policies.

Plug-In Hybrid Urban Delivery Truck Technology Demonstration

Energy Technology Data Exchange (ETDEWEB)

Miyasato, Matt [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Impllitti, Joseph [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Pascal, Amar [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States)

2015-07-31

The I-710 and CA-60 highways are key transportation corridors in the Southern California region that are heavily used on a daily basis by heavy duty drayage trucks that transport the cargo from the ports to the inland transportation terminals. These terminals, which include store/warehouses, inland-railways, are anywhere from 5 to 50 miles in distance from the ports. The concentrated operation of these drayage vehicles in these corridors has had and will continue to have a significant impact on the air quality in this region whereby significantly impacting the quality of life in the communities surrounding these corridors. To reduce these negative impacts it is critical that zero and near-zero emission technologies be developed and deployed in the region. A potential local market size of up to 46,000 trucks exists in the South Coast Air Basin, based on near- dock drayage trucks and trucks operating on the I-710 freeway. The South Coast Air Quality Management District (SCAQMD), California Air Resources Board (CARB) and Southern California Association of Governments (SCAG) — the agencies responsible for preparing the State Implementation Plan required under the federal Clean Air Act — have stated that to attain federal air quality standards the region will need to transition to broad use of zero and near zero emission energy sources in cars, trucks and other equipment (Southern California Association of Governments et al, 2011). SCAQMD partnered with Volvo Trucks to develop, build and demonstrate a prototype Class 8 heavy-duty plug-in hybrid drayage truck with significantly reduced emissions and fuel use. Volvo’s approach leveraged the group’s global knowledge and experience in designing and deploying electromobility products. The proprietary hybrid driveline selected for this proof of concept was integrated with multiple enhancements to the complete vehicle in order to maximize the emission and energy impact of electrification. A detailed review of all

Planning of Truck Platoons: a Literature Review and Directions for Future Research

NARCIS (Netherlands)

A. Kishore Bhoopalam (Anirudh); N.A.H. Agatz (Niels); R.A. Zuidwijk (Rob)

2017-01-01

textabstractA truck platoon is a set of virtually linked trucks that drive closely behind one another using automated driving technology. Benefits of truck platooning include cost savings, reduced emissions, and more efficient utilization of road capacity. To fully reap these benefits in the initial

Voluntary Truck and Bus Fuel-Economy-Program marketing plan. Final technical report, September 29, 1980-January 29, 1982

Energy Technology Data Exchange (ETDEWEB)

None

1982-01-01

The aim of the program is to improve the utilization of fuel by commercial trucks and buses by updating and implementing specific approaches for educating and monitoring the trucking industry on methods and means of conserving fuels. The following outlines the marketing plan projects: increase use of program logo by voluntary program members and others; solicit trade publication membership and support; brief Congressional delegations on fuel conservation efforts; increase voluntary program presence before trade groups; increase voluntary program presence at truck and trade shows; create a voluntary program display for use at trade shows and in other areas; review voluntary program graphics; increase voluntary program membership; and produce placemats carrying fuel conservation messages; produce a special edition of Fuel Economy News, emphasizing the driver's involvement in fuel conservation; produce posters carrying voluntary program fuel conservation message. Project objectives, activities, and results for each project are summarized.

77 FR 12356 - Pilot Program on NAFTA Trucking Provisions

Science.gov (United States)

2012-02-29

...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that applied to participate in the Agency's long-haul pilot program to test and demonstrate the ability... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

78 FR 25525 - Pilot Program on NAFTA Trucking Provisions

Science.gov (United States)

2013-05-01

...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration..., which applied to participate in the Agency's long-haul pilot program to test and demonstrate the ability... long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled motor carriers...

77 FR 40938 - Pilot Program on NAFTA Trucking Provisions

Science.gov (United States)

2012-07-11

...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... Morales Guevara (DBA Fletes Morales) which applied to participate in the Agency's long-haul pilot program...] its intent to proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot...

76 FR 56272 - Pilot Project on NAFTA Trucking Provisions

Science.gov (United States)

2011-09-12

...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... cross-border long-haul trucking pilot program to test and demonstrate the ability of Mexico-domiciled...

Use of illicit drugs by truck drivers arriving at Paranaguá port terminal, Brazil.

Science.gov (United States)

Peixe, Tiago Severo; de Almeida, Rafael Menck; Girotto, Edmarlon; de Andrade, Selma Maffei; Mesas, Arthur Eumann

2014-01-01

The purpose of this study was to estimate the prevalence of recent use of illicit drugs among truck drivers who had parked their vehicles at the terminal port in Paranaguá City at Paraná State, southern Brazil. This cross-sectional study was part of a larger research project conducted among drivers at a regional Brazilian port. Data on professional characteristics, involvement in road traffic injuries, sleep, and use of alcohol and illicit drugs were collected using a questionnaire. Urine samples were collected and analyzed for amphetamines, cocaine, and cannabis using gas chromatography with mass spectrometric detection. Sixty-two drivers were included in the study. Toxicological analyses showed that 8.1 percent (95% confidence interval [CI], 2.7-17.8%) of the urine samples were positive for drugs (4.8% for cocaine, 1.6% for amphetamine, and 1.6% for both); 8.1 percent reported drug use during the preceding 30 days in the questionnaire and only one tested positive for the drug in the urine sample. No sample was positive for cannabinoids. In total, at least 14.5 percent (95% CI, 6.9-25.8%) had used illicit drugs during the preceding 30 days based on self-reports and urine testing. Drivers who reported involvement in traffic injuries the year before more often tested positive for drugs in biological samples (P illicit stimulants was common among professional truck drivers transporting grain loads. Thus, actions are needed to reduce drug use among truck drivers in order to prevent drug-related road traffic injuries.

A review of suspected cases of driving under the influence of drugs (DUID) involved in traffic accidents in Istanbul (Turkey).

Science.gov (United States)

Acar, Fatih; Asirdizer, Mahmut; Aker, Rezzan Gulhan; Kucukibrahimoglu, E Esra; Ates, Ismail; Erol, Yeter; Sahin, Aysegul

2013-08-01

Nowadays traffic accidents, which have high mortality and morbidity, are an important public health problem. The association between the use of alcohol and/or drugs by drivers and the increased risk of traffic accidents with a high risk of death and injury has been well described in the literature. This study aimed to review the incidence of cases of driving under the influence of drugs (DUID) among all cases of driving under the influence (DUI) of alcohol and/or other drugs involved in traffic accidents and to evaluate the type of the psychoactive drugs (with or without alcohol) detected in blood samples in Istanbul and its surrounding area. This study is the first investigation on the subject of DUID cases in Turkey. The reports of the Istanbul Toxicology Department of the Council of Forensic Medicine (Turkey) on suspected DUID cases involved in traffic accidents between 1 July 2010 and 30 June 2011 were retrospectively reviewed for alcohol and/or drug use. Alcohol analysis was requested in 4274 suspected DUI cases, whereas drug along with alcohol analysis was requested in only 91. The rate of suspected DUID cases (n = 91) among the suspected DUI cases (n = 4274) was only 2.1% and in this study, we evaluated only the DUID cases in detail. Alcohol was present in 44% of suspected DUID cases. Psychoactive drugs were present in 15.4% of cases. The incidence among 46 confirmed DUID cases was found to be 17.4% for cannabis, 8.7% for benzodiazepines, 4.3% for barbiturates, 4.3% for antidepressants, 2.2% for cocaine and 2.2% for amphetamines. Although there is a zero-tolerance approach for DUID in the Turkish regulations, it is not well recognised and not inspected by police and legal authorities who are responsible for taking measures in traffic accidents and for routine traffic controls in Turkey. It is concluded that psychoactive drugs should be checked as well as alcohol in all traffic accident cases and roadside controls. Copyright © 2013 Elsevier Ltd and Faculty

Characteristics of worker accidents on NYSDOT construction projects.

Science.gov (United States)

Mohan, Satish; Zech, Wesley C

2005-01-01

This paper aims at providing cost-effective safety measures to protect construction workers in highway work zones, based on real data. Two types of accidents that occur in work zones were: (a) construction work area accidents, and (b) traffic accidents involving construction worker(s). A detailed analysis of work zone accidents involving 36 fatalities and 3,055 severe injuries to construction workers on New York State Department of Transportation (NYSDOT) construction projects from 1990 to 2001 established that five accident types: (a) Struck/Pinned by Large Equipment, (b) Trip or Fall (elevated), (c) Contact w/Electrical or Gas Utility, (d) Struck-by Moving/Falling Load, and (e) Crane/Lift Device Failure accounted for nearly 96% of the fatal accidents, nearly 63% of the hospital-level injury accidents, and nearly 91% of the total costs. These construction work area accidents had a total cost of $133.8 million. Traffic accidents that involve contractors' employees were also examined. Statistical analyses of the traffic accidents established that five traffic accident types: (a) Work Space Intrusion, (b) Worker Struck-by Vehicle Inside Work Space, (c) Flagger Struck-by Vehicle, (d) Worker Struck-by Vehicle Entering/Exiting Work Space, and (e) Construction Equipment Struck-by Vehicle Inside Work Space accounted for nearly 86% of the fatal, nearly 70% of the hospital-level injury and minor injury traffic accidents, and $45.4 million (79.4%) of the total traffic accident costs. The results of this paper provide real statistics on construction worker related accidents reported on construction work zones. Potential preventions based on real statistics have also been suggested. The ranking of accident types, both within the work area as well as in traffic, will guide the heavy highway contractor and owner agencies in identifying the most cost effective safety preventions.

ISAF'S Afghan Truck Drivers: The Overlooked Counterinsurgency Population

Directory of Open Access Journals (Sweden)

Myron Varouhakis

2015-12-01

Full Text Available A yearlong U.S. Army field study in Afghanistan examined the demographics and threat perceptions of one of the most-at-risk populations, that of Afghan truck drivers working for NATO’s International Security Assistance Force Afghanistan (ISAF. The study collected data from 766 Afghan truck drivers at the U.S.-operated Kandahar Airfield in ISAF’s Regional Command South. The findings show a wide diversity in age of the Afghan drivers as well as in terms of their home province. The findings also show that although all Afghan truck drivers had acute awareness and understanding of the high risks and dangers of the job, they all noted that the attractive salary and scarcity of jobs were dominant reasons for staying on the job. Findings also reveal a strong resentment among the Afghan truck drivers about their treatment by ISAF soldiers, as for the lack of protection for them and their families after the 2014 departure of NATO forces. The findings can provide significant insights and enhance the understanding of scholars, counterinsurgency strategists, policymakers, and military planners about “Host Country Nationals” as an important population of the human terrain.

The covariance between the number of accidents and the number of victims in multivariate analysis of accident related outcomes

NARCIS (Netherlands)

Bijleveld, F. D.

In this study some statistical issues involved in the simultaneous analysis of accident related outcomes of the road traffic process are investigated. Since accident related outcomes like the number of victims, fatalities or accidents show interdependencies, their simultaneous analysis requires that

76 FR 56868 - Pilot Project on NAFTA Trucking Provisions

Science.gov (United States)

2011-09-14

...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to test and...

77 FR 27837 - Pilot Program on NAFTA Trucking Provisions

Science.gov (United States)

2012-05-11

...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... carriers that applied to participate in the Agency's long- haul pilot program to test and demonstrate the... intent to proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to...

76 FR 73765 - Pilot Project on NAFTA Trucking Provisions

Science.gov (United States)

2011-11-29

...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... that have applied to participate in the Agency's long- haul pilot program to test and demonstrate the... proceed with the initiation of a U.S.-Mexico cross-border long-haul trucking pilot program to test and...

27 CFR 24.229 - Tank car and tank truck requirements.

Science.gov (United States)

2010-04-01

... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Spirits § 24.229 Tank car and tank truck requirements. Railroad tank cars and tank trucks used to transport spirits for use in wine production will be constructed...

Accidents in nuclear ships

Energy Technology Data Exchange (ETDEWEB)

Oelgaard, P L [Risoe National Lab., Roskilde (Denmark); [Technical Univ. of Denmark, Lyngby (Denmark)

1996-12-01

This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10{sup -3} per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au).

Accidents in nuclear ships

International Nuclear Information System (INIS)

Oelgaard, P.L.

1996-12-01

This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10 -3 per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au)

Could Expanded Freight Rail Reduce Air Pollution from Trucks?

Science.gov (United States)

Bickford, E. E.; Holloway, T.; Johnston, M.

2010-12-01

Cars, trucks and trains are a significant source of emissions that impact both climate and air quality on regional to global scales. Diesel vehicles, most used for freight transport, account for 42% of on-road nitrogen oxide emissions, 58% of on-road fine particulate emissions, and 21% of on-road carbon dioxide emissions. With freight tonnage projected to increase 28% by 2018, and freight trucks the fastest growing source of transportation emissions, we evaluate the potential for increased rail capacity to reduce the environmental impacts of trucks. Most widely available mobile source emissions inventories contain insufficient spatial detail to quantify realistic emission scenario options, and none to date have been linked with commodity flow information in a manner appropriate to consider the true potential of rail substitution. To support a truck-to-rail analysis, and other policy assessments requiring roadway-by-roadway analysis, we have developed a freight emissions inventory for the Upper Midwest based on the Federal Highway Administration’s Freight Analysis Framework version 2.2 and the Environmental Protection Agency’s on-road emissions model, Mobile6.2. Using a Geographical Information System (GIS), we developed emissions scenarios for truck-to-rail modal shifts where 95% of freight tonnage on trips longer than 400 miles is shifted off of trucks and onto railways. Scenarios will be analyzed with the Community Multiscale Air Quality (CMAQ) regional model to assess air quality impacts of associated changes. By using well-respected transportation data and realistic assumptions, results from this study have the potential to inform decisions on transportation sustainability, carbon management, public health, and air quality.

Heavy truck modeling for fuel consumption. Simulations and measurements

Energy Technology Data Exchange (ETDEWEB)

Sandberg, T.

2001-12-01

Fuel consumption for heavy trucks depends on many factors like roads, weather, and driver behavior that are hard for a manufacturer to influence. However, one design possibility is the power train configuration. Here a new simulation program for heavy trucks is created to find the configuration of the power train that gives the lowest fuel consumption for each transport task. For efficient simulations the model uses production code for speed and gear control, and it uses exchangeable data sets to allow simulation of the whole production range of engine types, on recorded road profiles from all over the world. Combined with a graphical user interface this application is called STARS (Scania Truck And Road Simulation). The forces of rolling resistance and air resistance in the model are validated through an experiment where the propeller shaft torque of a heavy truck is measured. It is found that the coefficient of rolling resistance is strongly dependent on tire temperature, not only on vehicle speed as expected. This led to the development of a new model for rolling resistance. The model includes the dynamic behavior of the tires and relates rolling resistance to tire temperature and vehicle speed. In another experiment the fuel consumption of a test truck in highway driving is measured. The altitude of the road is recorded with a barometer and used in the corresponding simulations. Despite of the limited accuracy of this equipment the simulation program manage to predict a level of fuel consumption only 2% lower than the real measurements. It is concluded that STARS is a good tool for predicting fuel consumption for trucks in highway driving and for comparing different power train configurations.

[Accidents and injuries at work].

Science.gov (United States)

Standke, W

2014-06-01

In the case of an accident at work, the person concerned is insured by law according to the guidelines of the Sozialgesetzbuch VII as far as the injuries have been caused by this accident. The most important source of information on the incident in question is the accident report that has to be sent to the responsible institution for statutory accident insurance and prevention by the employer, if the accident of the injured person is fatal or leads to an incapacity to work for more than 3 days (= reportable accident). Data concerning accidents like these are sent to the Deutsche Gesetzliche Unfallversicherung (DGUV) as part of a random sample survey by the institutions for statutory accident insurance and prevention and are analyzed statistically. Thus the key issues of accidents can be established and used for effective prevention. Although the success of effective accident prevention is undisputed, there were still 919,025 occupational accidents in 2011, with clear gender-related differences. Most occupational accidents involve the upper and lower extremities. Accidents are analyzed comprehensively and the results are published and made available to all interested parties in an effort to improve public awareness of possible accidents. Apart from reportable accidents, data on the new occupational accident pensions are also gathered and analyzed statistically. Thus, additional information is gained on accidents with extremely serious consequences and partly permanent injuries for the accident victims.

Scheduling Trucks in a Cross-Dock with Mixed Service Mode Dock Doors

DEFF Research Database (Denmark)

Bodnar, Peter; Azadeh, Kaveh; Koster, René de

2017-01-01

The problem considered in this paper is how to schedule inbound and outbound trucks subject to time windows at a multidoor cross-dock. Dock doors can either be dedicated to inbound or outbound trucks or be capable of handling both truck types. In addition, loads are allowed to be temporarily...

Emergency Response to Radioactive Material Transport Accidents

International Nuclear Information System (INIS)

EL-shinawy, R.M.K.

2009-01-01

Although transport regulations issued by IAEA is providing a high degree of safety during transport opertions,transport accidents involving packages containing radioactive material have occurred and will occur at any time. Whenever a transport accident involving radioactive material accurs, and many will pose no radiation safety problems, emergency respnose actioms are meeded to ensure that radiation safety is maintained. In case of transport accident that result in a significant relesae of radioactive material , loss of shielding or loss of criticality control , that consequences should be controlled or mitigated by proper emergency response actions safety guide, Emergency Response Plamming and Prepardness for transport accidents involving radioactive material, was published by IAEA. This guide reflected all requirememts of IAEA, regulations for safe transport of radioactive material this guide provide guidance to the publicauthorites and other interested organziation who are responsible for establishing such emergency arrangements

Enhanced safety features of CHASHMA NPP UNIT-2 to encounter selected severe accidents, various challenges involved to prove the adequacy of severe accidents prevention/mitigation measures and to write management guidelines with one possible solution to these challenges

International Nuclear Information System (INIS)

Iqbal, Z.; Minhaj, A.

2007-01-01

This paper describes enhanced safety features of Chashma Nuclear Power Plant Unit-2 (C-2), a 325 MWe PWR to encounter selected severe accidents and discusses various challenges involved to prove the adequacy of severe accidents encountering measures and to write severe accident management guidelines (SAMGs) in compliance with the recently introduced national regulations based on the new IAEA nuclear safety standards. C-2 is being built by China National Nuclear Corporation (CNNC) for Pakistan Atomic Energy Commission (PAEC). Its twin, Unit-1 (C-1) also a 325 MWe PWR, was commissioned in 2000. Nuclear power safety with reference to severe accidents should be treated as a global issue and therefore the developed countries should include the people of developing countries in nuclear power industry's various severe accidents based research and development programs. The implementation of this idea may also deliver few other useful and mutually beneficial byproducts. (author)

Activity Recognition and Localization on a Truck Parking Lot

NARCIS (Netherlands)

Andersson, M.; Patino, L.; Burghouts, G.J.; Flizikowski, A.; Evans, M.; Gustafsson, D.; Petersson, H.; Schutte, K.; Ferryman, J.

2013-01-01

In this paper we present a set of activity recognition and localization algorithms that together assemble a large amount of information about activities on a parking lot. The aim is to detect and recognize events that may pose a threat to truck drivers and trucks. The algorithms perform zone-based

A comparison of pipeline versus truck transport of bio-oil.

Science.gov (United States)

Pootakham, Thanyakarn; Kumar, Amit

2010-01-01

Biomass-based energy and fuels are receiving attention because they are considered carbon neutral; i.e. the amount of CO(2) released during combustion of this biomass is nearly the same as that taken up by the plants during their growth. Bio-oil is a dark viscous liquid consisting of hydrocarbons. These are produced by fast pyrolysis of biomass. "As-is" biomass material has a low energy density (MJ m(-3)), hence, the cost of transporting this energy is high. Bio-oil has a high energy density as compared to "as-is" biomass material, consequently it helps in reducing the cost of energy transport. This study compares the life cycle assessment of transportation of bio-oil by pipeline with that by truck. The scope of the work includes the transportation of bio-oil by truck or pipeline from a centralized plant (supplied with forest biomass) to an end-user. Two cases are studied for pipeline transport of bio-oil: the first case considers a coal-based electricity supply for pumping the bio-oil through a pipeline; the second case considers an electricity supply from a renewable resource. The two cases of pipeline transport are compared to two cases of truck transport (truck trailer and super B-train truck). The life cycle greenhouse gas (GHG) emissions from the pipeline transport of bio-oil for the two cases of electricity supply are 345 and 17 g of CO(2) m(-3) km(-1), respectively. Similar values for transport by trailer (capacity - 30 m(3)) and super B-train truck (capacity - 60 m(3)) are 89 and 60 g of CO(2) m(-3) km(-1), respectively. Energy input for bio-oil transport is 3.95 MJ m(-3) km(-1) by pipeline, 2.59 MJ m(-3) km(-1) by truck and 1.66 MJ m(-3) km(-1) by super B-train truck. The results show that GHG emissions in pipeline transport are largely dependent on the source of electricity (higher for coal-based electricity). Substituting 250 m(3) day(-1) of pipeline-transported bio-oil for coal-based electricity can mitigate about 5.1 million tonnes of CO(2) per year

[Analysis on on-site rescue and traumatic features of victims involved in gas explosion accident in Hangzhou].

Science.gov (United States)

Wang, X G; Jin, R H; Liu, F P; Han, C M

2017-10-20

Objective: To investigate the situations of on-site rescue and traumatic features of victims involved in gas explosion accident in Hangzhou, so as to provide more data support for emergency medical rescues of the similar incidents of massive casualty. Methods: Two medical workers with a certain clinical experience were sent to Hangzhou 120 emergency medical centers to collect data of the on-site rescue on 21st July, 2017, including ambulance call-outs, on-site command and traffic conditions, and on-site triage and evacuation of the victims. They were then sent to the hospitals receiving the victims to investigate the situations of these victims including the general information (such as gender, age, admitted hospitals, and number of admission, discharge, and transferring in the first two weeks after the accident) and injury assessment [such as injury position and type, injury severity evaluation by New Injury Severity Scoring (NISS), and burn severity evaluation for victims with burns]. Results: (1) A total of 15 ambulances reached the accident site for rescue. The traffic and transportation were jammed and interrupted after this accident. On-site triage and distribution were disorderly conducted. (2) Clinical data of 53 victims were collected, including 24 males and 29 females, with the age of 8 to 70 (34±14) years old. They were sent into 6 hospitals in Hangzhou. Two victims died on the day of accident. Up to two weeks after this accident, 28 (52.8%) victims were discharged from the hospitals and received follow-up in outpatient department. Five victims with severe injuries were transferred to the other hospitals. (3) Based on the results of NISS, the injury severities were mild in 29 (54.7%) cases, moderate in 9 (17.0%) cases, serious in 3 (5.7%) cases, and severe in 12 (22.6%) cases. Those 2 dead victims were classified into the severe category due to the highest NISS score of 75. For all of the victims, skin and soft tissue defects were most common. Six (11

The Aerodynamics of Heavy Vehicles III : Trucks, Buses and Trains

CERN Document Server

Orellano, Alexander

2016-01-01

This volume contains papers presented at the International conference “The Aerodynamics of Heavy Vehicles III: Trucks, Buses and Trains” held in Potsdam, Germany, September 12-17, 2010 by Engineering Conferences International (ECI). Leading scientists and engineers from industry, universities and research laboratories, including truck and high-speed train manufacturers and operators were brought together to discuss computer simulation and experimental techniques to be applied for the design of more efficient trucks, buses and high-speed trains in the future.   This conference was the third in the series after Monterey-Pacific Groove in 2002 and Lake Tahoe in 2007.  The presentations address different aspects of train aerodynamics (cross wind effects, underbody flow, tunnel aerodynamics and aeroacoustics, experimental techniques), truck aerodynamics (drag reduction, flow control, experimental and computational techniques) as well as computational fluid dynamics and bluff body, wake and jet flows.

Impact of left lane truck restriction strategies on multilane highways in Louisiana : a literature review.

Science.gov (United States)

2009-04-01

Truck lane restriction strategies (TLRS) are a means of managing truck traffic on highways by prohibiting trucks from using certain lanes to minimize interaction between trucks and other vehicles. The purpose of this study is to review the literature...

Waste Management's LNG Truck Fleet: Final Results

Energy Technology Data Exchange (ETDEWEB)

Chandler, K. [Battelle (US); Norton, P. [National Renewable Energy Laboratory (US); Clark, N. [West Virginia University (US)

2001-01-25

Waste Management, Inc., began operating a fleet of heavy-duty LNG refuse trucks at its Washington, Pennsylvania, facility. The objective of the project was to provide transportation professionals with quantitative, unbiased information on the cost, maintenance, operational, and emissions characteristics of LNG as one alternative to conventional diesel for heavy-duty trucking applications.

Routing and Scheduling Problems of Container Trucks in a Shared Resource Environment

OpenAIRE

Jeong, Kyungsoo

2017-01-01

More frequent vehicle movements are required for moving containers in a local area due to low unit volume that a single vehicle can handle compared with vessels and rails involved in the container supply chain. For this reason, truck operations for moving containers significantly affect not only transportation cost itself but also product price. They have inherent operational inefficiencies associated with empty container movements and container processes at facilities such as warehouses, d...

Human Factors in Accidents Involving Remotely Piloted Aircraft

Science.gov (United States)

Merlin, Peter William

2013-01-01

This presentation examines human factors that contribute to RPA mishaps and provides analysis of lessons learned. RPA accident data from U.S. military and government agencies were reviewed and analyzed to identify human factors issues. Common contributors to RPA mishaps fell into several major categories: cognitive factors (pilot workload), physiological factors (fatigue and stress), environmental factors (situational awareness), staffing factors (training and crew coordination), and design factors (human machine interface).

Factors contributing to young moped rider accidents in Denmark.

Science.gov (United States)

Møller, Mette; Haustein, Sonja

2016-02-01

Young road users still constitute a high-risk group with regard to road traffic accidents. The crash rate of a moped is four times greater than that of a motorcycle, and the likelihood of being injured in a road traffic accident is 10-20 times higher among moped riders compared to car drivers. Nevertheless, research on the behaviour and accident involvement of young moped riders remains sparse. Based on analysis of 128 accident protocols, the purpose of this study was to increase knowledge about moped accidents. The study was performed in Denmark involving riders aged 16 or 17. A distinction was made between accident factors related to (1) the road and its surroundings, (2) the vehicle, and (3) the reported behaviour and condition of the road user. Thirteen accident factors were identified with the majority concerning the reported behaviour and condition of the road user. The average number of accident factors assigned per accident was 2.7. Riding speed was assigned in 45% of the accidents which made it the most frequently assigned factor on the part of the moped rider followed by attention errors (42%), a tuned up moped (29%) and position on the road (14%). For the other parties involved, attention error (52%) was the most frequently assigned accident factor. The majority (78%) of the accidents involved road rule breaching on the part of the moped rider. The results indicate that preventive measures should aim to eliminate violations and increase anticipatory skills among moped riders and awareness of mopeds among other road users. Due to their young age the effect of such measures could be enhanced by infrastructural measures facilitating safe interaction between mopeds and other road users. Copyright © 2015 Elsevier Ltd. All rights reserved.

Powershift transmission for dump trucks; Neues Lastschaltgetriebe fuer Dump Trucks

Energy Technology Data Exchange (ETDEWEB)

Rebholz, Wolfgang; Geis, Joerg; Riedhammer, Michael [ZF Friedrichshafen AG, Friedrichshafen (Germany)

2012-04-15

Articulated dumpers (also called dump trucks) are used in many locations where large quantities of earth, spoil, gravel or other materials have to be moved on construction sites or in quarries. ZF has developed a new transmission with eight forward and four reverse gears up to production standard specifically for use in these vehicles. The integrated primary retarder is continuously controllable and provides maximum braking torque of up to 1800 Nm. (orig.)

The significance of domino effect in chemical accidents

OpenAIRE

Hemmatian, Behrouz; Abdolhamidzadeh, B; Darbra Roman, Rosa Maria; Casal Fàbrega, Joaquim

2014-01-01

A historical survey was performed on 330 accidents involving domino effect, occurred in process/storage plants and in the transportation of hazardous materials; only accidents occurred after 1st-January-1961 have been considered. The main features – geographical location, type of accident, materials involved, origin and causes, consequences, domino sequences – were analyzed, with special consideration to the situation in the developing countries and compared to those from other previous surve...

Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

Energy Technology Data Exchange (ETDEWEB)

Nuuja, J [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

1997-12-31

In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

Energy Technology Data Exchange (ETDEWEB)

Nuuja, J. [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A. [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

1996-12-31

In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

Truck Route Choice Modeling using Large Streams of GPS Data

Science.gov (United States)

2017-07-31

The primary goal of this research was to use large streams of truck-GPS data to analyze travel routes (or paths) chosen by freight trucks to travel between different origin and destination (OD) location pairs in metropolitan regions of Florida. Two s...

49 CFR 230.108 - Steam locomotive leading and trailing trucks.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Steam locomotive leading and trailing trucks. 230... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives and Tenders Trucks, Frames and Equalizing System § 230.108 Steam locomotive leading...

Accident management insights after the Fukushima Daiichi NPP accident

International Nuclear Information System (INIS)

Degueldre, Didier; Viktorov, Alexandre; Tuomainen, Minna; Ducamp, Francois; Chevalier, Sophie; Guigueno, Yves; Tasset, Daniel; Heinrich, Marcus; Schneider, Matthias; Funahashi, Toshihiro; Hotta, Akitoshi; Kajimoto, Mitsuhiro; Chung, Dae-Wook; Kuriene, Laima; Kozlova, Nadezhda; Zivko, Tomi; Aleza, Santiago; Jones, John; McHale, Jack; Nieh, Ho; Pascal, Ghislain; ); Nakoski, John; Neretin, Victor; Nezuka, Takayoshi; )

2014-01-01

events and accidents at NPPs, and what additional measures should be considered as an accident progresses to the severe accident stage. Insights are provided on the experiences and practices existing or being proposed in the NEA member states, as well as new findings from post-Fukushima studies. Emphasis is placed on identifying commendable practices that support enhanced and integrated on-site accident management response and decision-making by NPP operators. The report provides information (including commendable practices) useful for regulatory authorities to consider as they implement enhancements to their regulatory framework in the area of integrated accident management building on the lessons learnt from the Fukushima Daiichi NPP accident. The report's insights also should be useful to regulatory authorities, operating organisations and others in the nuclear safety community for addressing accident management issues such as procedures and guidelines, equipment, infrastructure and instrumentation, and human and organisational resources. Factors such as accidents involving spent fuel pools, multi-unit aspects of accident management, the interface between onsite and off-site organisations and resources, and degradation of the surrounding infrastructure are also discussed. (authors)

French policy for managing the post-accident phase of a nuclear accident.

Science.gov (United States)

Gallay, F; Godet, J L; Niel, J C

2015-06-01

In 2005, at the request of the French Government, the Nuclear Safety Authority (ASN) established a Steering Committee for the Management of the Post-Accident Phase of a Nuclear Accident or a Radiological Emergency, with the objective of establishing a policy framework. Under the supervision of ASN, this Committee, involving several tens of experts from different backgrounds (e.g. relevant ministerial offices, expert agencies, local information commissions around nuclear installations, non-governmental organisations, elected officials, licensees, and international experts), developed a number of recommendations over a 7-year period. First published in November 2012, these recommendations cover the immediate post-emergency situation, and the transition and longer-term periods of the post-accident phase in the case of medium-scale nuclear accidents causing short-term radioactive release (less than 24 h) that might occur at French nuclear facilities. They also apply to actions to be undertaken in the event of accidents during the transportation of radioactive materials. These recommendations are an important first step in preparation for the management of a post-accident situation in France in the case of a nuclear accident. © The Chartered Institution of Building Services Engineers 2014.

Investigation of human body vibration exposures on haul trucks operating at U.S. surface mines/quarries relative to haul truck activity

Science.gov (United States)

Mayton, Alan G.; Porter, William L.; Xu, Xueyan S.; Weston, Eric B.; Rubenstein, Elaine N.

2018-01-01

Workers who operate mine haul trucks are exposed to whole-body vibration (WBV) on a routine basis. Researchers from the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) investigated WBV and hand-arm vibration (HAV) exposures for mine/quarry haul truck drivers in relation to the haul truck activities of dumping, loading, and traveling with and without a load. The findings show that WBV measures in weighted root-mean-square accelerations (aw) and vibration dose value (VDV), when compared to the ISO/ANSI and European Directive 2002/44/EC standards, were mostly below the Exposure Action Value (EAV) identified by the health guidance caution zone (HGCZ). Nevertheless, instances were recorded where the Exposure Limit Value (ELV) was exceeded by more than 500 to 600 percent for VDVx and awx, respectively. Researchers determined that these excessive levels occurred during the traveling empty activity, when the haul truck descended down grade into the pit loading area, sliding at times, on a wet and slippery road surface caused by rain and overwatering. WBV levels (not normalized to an 8-h shift) for the four haul truck activities showed mean awz levels for five of the seven drivers exceeding the ISO/ANSI EAV by 9–53 percent for the traveling empty activity. Mean awx and awz levels were generally higher for traveling empty and traveling loaded and lower for loading/dumping activities. HAV for measures taken on the steering wheel and shifter were all below the HGCZ which indicates that HAV is not an issue for these drivers/operators when handling steering and shifting control devices. PMID:29725145

Vehicle to Grid regulation services of electric delivery trucks: Economic and environmental benefit analysis

International Nuclear Information System (INIS)

Zhao, Yang; Noori, Mehdi; Tatari, Omer

2016-01-01

Highlights: • Potential net present revenues of electric truck based V2G regulation services are investigated. • GHG emission mitigation of V2G regulation services provided by electric trucks are quantified. • The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed. • V2G regulation services for electric trucks could yield considerable revenues and GHG emission savings. - Abstract: Concerns regarding the fuel costs and climate change impacts associated with petroleum combustion are among the main driving factors for the adoption of electric vehicles. Future commercial delivery truck fleets may include Battery Electric Vehicles (BEVs) and Extended Range Electric Vehicles (EREVs); in addition to savings on fuel and maintenance costs, the introduction of these grid accessible electric vehicles will also provide fleet owners with possible Vehicle to Grid (V2G) opportunities. This study investigates the potential net present revenues and greenhouse gas (GHG) emission mitigation of V2G regulation services provided by electric trucks in a typical fleet. The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed and compared to those of traditional diesel trucks. To account for uncertainties, possible ranges for key parameters are considered instead of only considering fixed single data values for each parameter. The results of this research indicate that providing V2G regulation services for electric trucks could yield considerable additional revenues ($20,000–50,000) and significant GHG emission savings (approximately 300 ton CO_2) compared to conventional diesel trucks.

IMPROVING THE ORGANIZATION OF THE SHOVEL-TRUCK SYSTEMS IN OPEN-PIT COAL MINES

Directory of Open Access Journals (Sweden)

Mark KORYAGIN

2017-06-01

Full Text Available The aim of the study is to reduce idle times of mining trucks and shovels in an open-pit coal mine. A heuristic algorithm for making dispatching decisions in conditions of dynamic allocation of trucks is developed. Priority parameters for choosing the shovel after the end-of-truck unloading are introduced. Also, an algorithm for searching for the optimal priority parameters to satisfy the required efficiency criterion is developed. This algorithm is based on a simulation model of a shovel-truck system. The proposed approach is applicable in terms of the group of shovels with a common dump point in various open-pit coal mines. The importance of this work lies in the fact that the proposed model takes into account the random factors related with the duration of loading and dumping, truck movement, repair of shovels and haul trucks, as well as the duration of periods between repairs.

An empirical study of DSRC V2V performance in truck platooning scenarios

Directory of Open Access Journals (Sweden)

Song Gao

2016-11-01

Full Text Available Among many safety applications enabled by Dedicated Short Range Communication (DSRC, truck platooning provides many incentives to commercial companies. This paper studies DSRC Vehicle-to-Vehicle (V2V performance in truck platooning scenarios through real-world experiments. Commercial DSRC equipments and semi-trailer trucks are used in this study. We mount one DSRC antenna on each side of the truck. One set of dynamic tests and a few sets of static tests are conducted to explore DSRC behaviors under different situations. From the test results, we verified some of our speculations. For example, hilly roads can affect delivery ratio and antennas mounted on opposite sides of a truck can suffer from low delivery ratio at curved roads. In addition, we also found that antennas can sometimes suffer from low delivery ratio even when the trucks are on straight roads, possibly due to reflections from the nearby terrain. Fortunately, the delivery ratio can be greatly improved by using the two side antennas alternately.

Potentialities of robots in major accident situations

International Nuclear Information System (INIS)

Chevallier, M.

2013-01-01

The INTRA group was founded in 1988, 2 years after the Chernobyl accident with the purpose of a cooperation between EDF, Cogema and CEA in order to develop and operate a fleet of robots able to intervene and replace man in a nuclear facility in case of major accident. Now INTRA disposes of 5 types of equipment: first, robots for the inside of buildings (they can overcome 40 cm high obstacles, open doors, go upstairs) they are wire-guided and enjoy a battery life of 6 to 8 hours. Secondly, robots for the open air that are able to move in very degraded grounds, they are remote controlled through radio-waves and their autonomy range nears 5 km. Thirdly, public works vehicles, INTRA has developed an excavator and a dump truck, both are remote controlled, they allow the making of any earth work. Fourthly, INTRA has developed 2 systems of contamination measurement: Skylink and Helinuc. Skylink is a system of 20 radiation monitors that can be dispatched on the contaminated zone, their data is collected through radio waves. Helinuc is a kind of gamma spectrometer that is helicopter-borne and can draw a map of the contamination around the installation. Fifthly, 2 drones are being tested, they will be fitted with radiation monitors. (A.C.)

Measuring Timber Truck Loads With Image Processing In Paper Mills

Science.gov (United States)

Silva, M. Santos; Carvalho, Fernando D.; Rodrigues, F. Carvalho; Goncalves, Ana N. R.

1989-04-01

The raw material for the paper industry is wood. To have an exact account of the stock of piled sawn tree trunks every truck load entering the plant's stockyard must be measured as to the amount of wood being brought in. Weighting down the trucks has its own problems, mainly, due to the high capacity of the tree trunks to absorb water. This problem is further enhanced when calculations must be made to arrive at the mass of sawn tree trunks which must go into the process of producing a certain quantity of paper pulp. The method presented here is based on two fixed cameras which take the image of the truck load. One takes a view of the trunks in order to get information on the average length of the tree trunks. The other obtains a side view which is digitised and by just discriminating against a grey level the area covered by the tree trunk cross section is measured. A simple arithmetic operation gives the volume of wood in the trunk. The same computer, a PC, will register the trucks particulars is almost independent of weather the wood is wet or dry and it serves trucks of any size.

Acceptance test report for core sample trucks 3 and 4

International Nuclear Information System (INIS)

Corbett, J.E.

1996-01-01

The purpose of this Acceptance Test Report is to provide documentation for the acceptance testing of the rotary mode core sample trucks 3 and 4, designated as HO-68K-4600 and HO-68K-4647, respectively. This report conforms to the guidelines established in WHC-IP-1026, ''Engineering Practice Guidelines,'' Appendix M, ''Acceptance Test Procedures and Reports.'' Rotary mode core sample trucks 3 and 4 were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Successful completion of acceptance testing on June 30, 1995 verified that all design requirements were met. This report is divided into four sections, beginning with general information. Acceptance testing was performed on trucks 3 and 4 during the months of March through June, 1995. All testing was performed at the ''Rock Slinger'' test site in the 200 West area. The sequence of testing was determined by equipment availability, and the initial revision of the Acceptance Test Procedure (ATP) was used for both trucks. Testing was directed by ICF-KH, with the support of WHC Characterization Equipment Engineering and Characterization Project Operations. Testing was completed per the ATP without discrepancies or deviations, except as noted

Modeling and Design of Hybrid PEM Fuel Cell Systems for Lift Trucks

DEFF Research Database (Denmark)

Hosseinzadeh, Elham

driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need a long time to recharge and thus may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...... in a fork-lift truck. In order for the ejector to operate in the largest possible range of load, different approaches (with fixed nozzle and variable nozzle ejectors) have been investigated. Different geometries have been studied in order to optimize the ejector. The optimization is carried out not only...... a virtual fork-lift system. This investigation examines important performance metrics, such as hydrogen consumption and battery SOC as a function of the fuel cell and battery size, control strategy, drive cycle, and load variation for a fork-lift truck system. This study can be used as a benchmark...

[Drugs and occupational accident].

Science.gov (United States)

Bratzke, H; Albers, C

1996-02-01

In a case of a fatal occupational accident (construction worker, fall from roof, urine test positive for cocaine and THC, e.g. cannabis) the question arised to what extent those drug-related occupational accidents occur. In the literature only few cases, mainly dealing with cannabis influence, have been reported, however, a higher number is suspected. Cocaine and other stimulating drugs (amphetamine) are more often used to increase physical fitness. By direct or indirect interference with vigilance these compounds may provoke accidents. Due to the lack of a legal basis proving of the influence of drugs at the working place is still very limited, although highly sensitive chemical-toxicological assay procedures are available to detect even the chronic abuse (in hair). In the general conditions of accident insurances a compensation is excluded when alcohol is involved, but drugs are not mentioned. It is indeed difficult to establish a concentration limit for drugs like that existing for alcohol (1.1%). In each case the assay of the drug involved and exact knowledge of its specific effects is in an essential prerequisite to prove the causal relationship.

Road traffic accidents in Libya: An undeclared War

Directory of Open Access Journals (Sweden)

Ahmed Salamat

2008-01-01

Full Text Available To The Editor: In his outstanding article regarding Road Traffic Accidents (RTAs in Libya [1], Dr Abdulmajid Ali has raised awareness and started a debate about this extremely important issue. Before responding to some points in Dr Ali’s article, I would like to tell a real story of a tragic accident that happened last week, which highlights several issues related to RTAs in Libya. A 55 year old driver left after Fajr prayer to the vegetable market to buy a few things for his daughter’s wedding lunch. While trying to avoid a big pothole in the middle of the road, he was hit by a truck without headlights coming from the opposite direction. The truck driver continued driving as if nothing had happened. None of the road users cared to help the victim but he was able to contact his son by mobile phone to come and help him out of the wreckage. His son took him to the main Trauma Hospital in Tripoli. The patient had no external injuries. He was admitted for observation only. A few hours later the patient died as a result of major internal haemorrhage. Further information revealed that the truck driver had no driving licence and the truck was not road worthy.This story is not unique However, it highlights the complex and intermingled issues that need to be addressed to have any real impact on this disastrous problem in Libya. The specific points I would like to add to Dr Ali’s article are:There is no doubt that RTAs are a major killer in Libya especially in the young age group. The annual reporting of road causalities is considered to be the yard stick to measure the effectiveness of any national traffic policy,; in the UK for example the target is to reduce fatalities from RTAs by 50% by 2010 [2]. It is a disgrace not to have accurate official statistics published at least annually of fatalities, injuries, disabilities and the economic consequences of this undeclared war in Libya. There is evidence to support that there could be a positive

[Fatal occupational accidents in Lombardy].

Science.gov (United States)

Pianosi, G

1995-01-01

All fatal occupational accidents compensated in Lombardy from 1984 to 1989 were analyzed (1259 cases): significant differences between geographical distribution of fatal occupational accidents and workers were observed. Males accounted for about 95% of fatalities; an excess of cases was shown in both young and elderly workers. Death was the consequence of injuries involving most frequently the head, thorax and spinal cord. An excess of fatalities was observed in agriculture and, at a lower level, in manufacturing industries; small enterprises were involved in approximately 25% of fatalities occurring in the manufacturing industries and services. Employers were the victims of fatal accidents in 50% of cases in agriculture and in 70% of cases in craft industries. Construction, agriculture and transport accounted for about 50% of all fatalities. About 50% of fatal occupational accidents were related to vehicle use: the victim was the driver in the majority of cases, sometimes the victim was run over by a vehicle or fell from a vehicle. The results agree with some previous observations (e.g.: sex and age distribution; construction, agriculture and transport as working activities at high accident risk); but some original observations have emerged, in particular about the frequency of employers as victims and the role of vehicles in the genesis of fatal occupational accidents. If further studies confirm these latter observations, important developments could follow in preventive action design and implementation.

Investigation on occupant injury severity in rear-end crashes involving trucks as the front vehicle in Beijing area, China

Directory of Open Access Journals (Sweden)

Quan Yuan

2017-02-01

Conclusion: All the abovementioned significant factors should be improved, such as the conditions of lighting and the layout of lanes on roads. Two of the most common driver factors are drivers' age and drivers' original residence. Young drivers and outsiders have a higher injury severity. Therefore it is imperative to enhance the safety education and management on the young drivers who steer heavy duty truck from other cities to Beijing on weekdays.

Demonstration Project 111, ITS/CVO Technology Truck, Final Project Report

Energy Technology Data Exchange (ETDEWEB)

Gambrell, KP

2002-01-11

In 1995, the planning and building processes began to design and develop a mobile demonstration unit that could travel across the nation and be used as an effective outreach tool. In 1997, the unit was completed; and from June 1997 until December 2000, the Federal Highway Administration (FHWA)/Federal Motor Carrier Safety Administration (FMCSA) mobilized the Technology Truck, also known as Demonstration Project No. 111, ''Advanced Motor Carrier Operations and Safety Technologies.'' The project featured the latest available state-of-the-practice intelligent transportation systems (ITS) technologies designed to improve both the efficiency and safety of commercial vehicle operations (CVO). The Technology Truck was designed to inform and educate the motor carrier community and other stakeholders regarding ITS technologies, thus gaining support and buy-in for participation in the ITS program. The primary objective of the project was to demonstrate new and emerging ITS/CVO technologies and programs, showing their impact on motor carrier safety and productivity. In order to meet the objectives of the Technology Truck project, the FHWA/FMCSA formed public/private partnerships with industry and with Oak Ridge National Laboratory to demonstrate and display available ITS/CVO technologies in a cooperative effort. The mobile demonstration unit was showcased at national and regional conferences, symposiums, universities, truck shows and other venues, in an effort to reach as many potential users and decision makers as possible. By the end of the touring phase, the ITS/CVO Technology Truck had been demonstrated in 38 states, 4 Canadian provinces, 88 cities, and 114 events; been toured by 18,099 people; and traveled 115,233 miles. The market penetration for the Technology Truck exceeded 4,000,000, and the website received more than 25,000 hits. In addition to the Truck's visits, the portable ITS/CVO kiosk was demonstrated at 31 events in 23 cites in 15

Learning lessons from Natech accidents - the eNATECH accident database

Science.gov (United States)

Krausmann, Elisabeth; Girgin, Serkan

2016-04-01

When natural hazards impact industrial facilities that house or process hazardous materials, fires, explosions and toxic releases can occur. This type of accident is commonly referred to as Natech accident. In order to prevent the recurrence of accidents or to better mitigate their consequences, lessons-learned type studies using available accident data are usually carried out. Through post-accident analysis, conclusions can be drawn on the most common damage and failure modes and hazmat release paths, particularly vulnerable storage and process equipment, and the hazardous materials most commonly involved in these types of accidents. These analyses also lend themselves to identifying technical and organisational risk-reduction measures that require improvement or are missing. Industrial accident databases are commonly used for retrieving sets of Natech accident case histories for further analysis. These databases contain accident data from the open literature, government authorities or in-company sources. The quality of reported information is not uniform and exhibits different levels of detail and accuracy. This is due to the difficulty of finding qualified information sources, especially in situations where accident reporting by the industry or by authorities is not compulsory, e.g. when spill quantities are below the reporting threshold. Data collection has then to rely on voluntary record keeping often by non-experts. The level of detail is particularly non-uniform for Natech accident data depending on whether the consequences of the Natech event were major or minor, and whether comprehensive information was available for reporting. In addition to the reporting bias towards high-consequence events, industrial accident databases frequently lack information on the severity of the triggering natural hazard, as well as on failure modes that led to the hazmat release. This makes it difficult to reconstruct the dynamics of the accident and renders the development of

Risk assessment for truck-transport assuming different concepts of the back-end of the fuel cycle

International Nuclear Information System (INIS)

Tully, A.; Sonnenschein, R.; Haeusler, S.

1983-01-01

The different concepts of the back-end of the fuel cycle existing in the Federal Republic of Germany require that various types of radioactive materials will be transported along different pathways, for various distances and at different frequencies, thus resulting in different risks to the public. In one part of the second phase of the R + D program Projekt Sicherheitsstudien Entsorgung (PSE), the risk during normal and accident conditions will be assessed for each of the concepts of the back-end of the fuel cycle. Within this part of the safety analysis, DORNIER SYSTEM will determine the risks resulting from the transport of radioactive materials by truck, using the probabilistic method of fault tree analysis. This part of the investigation will extend until the end of 1983. 4 references, 5 tables

Accidents - Chernobyl accident; Accidents - accident de Tchernobyl

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

Weather delay costs to trucking.

Science.gov (United States)

2012-11-01

Estimates of the nations freight sector of transportation range to upwards of $600 billion of total gross domestic product with 70 percent of total value and 60 percent of total weight moving by truck. Weather-related delays can add significantly ...

Stake holder pre-involvement in the post accident management of rural areas: a government perspective

International Nuclear Information System (INIS)

Nisbet, A.F.; Mondon, K.J.

2002-01-01

In 1995 NRPB published an assessment of the applicability of a range of agricultural countermeasures for use in the UK. The study recommended that, for the purposes of contingency planning, a working group should be set up to bring together key groups that would be involved in intervention in -rural areas following a nuclear accident. This idea was taken forward by Government and in 1997 the Agriculture and Food Countermeasures Working Group was established. Participation is at a senior level by those involved in making policy decisions. The original membership has been expanded, and of the 22 representatives, 11 are currently from non-Government Organisations. The Group has met on five occasions and has successfully addressed all of its four terms of reference. From 2001 it will form the UK node of a European network of similar stakeholder groups being set up in Finland, France, Belgium and Greece. (author)

Estimation and analysis of multifactor productivity in truck transportation : 1987 - 2003

Science.gov (United States)

2009-02-01

The analysis has three objectives: 1) to estimate multifactor : productivity (MFP) in truck transportation during : 1987-2003; 2) to examine changes in multifactor productivity : in U.S. truck transportation, over time, and : to compare these changes...

43 CFR 15.13 - Report of accidents.

Science.gov (United States)

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Report of accidents. 15.13 Section 15.13 Public Lands: Interior Office of the Secretary of the Interior KEY LARGO CORAL REEF PRESERVE § 15.13 Report of accidents. Accidents involving injury to life or property shall be reported as soon as possible...

Dynamics of dump truck entrance onto the hoist platform of a mine inclined elevator

Energy Technology Data Exchange (ETDEWEB)

Nosyrev, B.A.; Popov, Yu.V.; Mukhutdinov, Sh.D. (Sverdlovskii Gornyi Institut (USSR))

1989-01-01

Analyzes the feasibility of transporting heavy-duty dump trucks along slopes on special platforms in coal surface mines. The platforms are hoisted by winches. Theoretical problems associated with hoisting a loaded platform upwards are analyzed. Problems associated with truck travel in the platform area, its exact positioning and mechanical vibrations of the platform caused by truck movement are discussed. Vibrations of the platform with a loaded truck and vibration amplitudes are analyzed. Five states of the system are evaluated. Methods for prevention of excessive vibrations by optimization of platform design and use of flexible elements are evaluated. Optimum speed of truck movement for platform entering is recommended.

Credible investigation of air accidents

International Nuclear Information System (INIS)

Smart, K.

2004-01-01

Within the United Kingdom the Air Accidents Investigation Branch (AAIB) has been used as a model for the other transport modes accident investigation bodies. Government Ministers considered that the AAIB's approach had established the trust of the public and the aviation industry in its ability to conduct independent and objective investigations. The paper will examine the factors that are involved in establishing this trust. They include: the investigation framework; the actual and perceived independence of the accident investigating body; the aviation industry's safety culture; the qualities of the investigators and the quality of their liaison with bereaved families those directly affected by the accidents they investigate

Large Truck Crash Causation Study (LTCCS)

Data.gov (United States)

Department of Transportation — The Large Truck* Crash Causation Study (LTCCS) is based on a three-year data collection project conducted by the Federal Motor Carrier Safety Administration (FMCSA)...

Occupational Hydrofluoric Acid Injury from Car and Truck Washing--Washington State, 2001-2013.

Science.gov (United States)

Reeb-Whitaker, Carolyn K; Eckert, Carly M; Anderson, Naomi J; Bonauto, David K

2015-08-21

Exposure to hydrofluoric acid (HF) causes corrosive chemical burns and potentially fatal systemic toxicity. Car and truck wash cleaning products, rust removers, and aluminum brighteners often contain HF because it is efficient in breaking down roadway matter. The death of a truck wash worker from ingestion of an HF-based wash product and 48 occupational HF burn cases associated with car and truck washing in Washington State during 2001-2013 are summarized in this report. Among seven hospitalized workers, two required surgery, and all but one worker returned to the job. Among 48 injured workers, job titles were primarily auto detailer, car wash worker, truck wash worker, and truck driver. Because HF exposure can result in potentially severe health outcomes, efforts to identify less hazardous alternatives to HF-based industrial wash products are warranted.

Normal Accident at Three Mile Island.

Science.gov (United States)

Perrow, Charles

1981-01-01

Discusses some aspects of the accident at the Three Mile Island nuclear power plant. Explains a number of factors involved including the type of accident, warnings, design and equipment failure, operator error, and negative synergy. Presents alternatives to systems with catastrophic potential. (MK)

75 FR 56651 - ITS Joint Program Office; Trucking Industry Mobility & Technology Coalition Annual Meeting

Science.gov (United States)

2010-09-16

... DEPARTMENT OF TRANSPORTATION ITS Joint Program Office; Trucking Industry Mobility & Technology... Transportation. ACTION: Notice. The Trucking Industry Mobility & Technology Coalition (TIMTC) Annual [[Page 56652...: Beating Gridlock with a Smart Grid; U.S. DOT Truck Technology Initiatives; and State and Federal...

Accident management information needs

International Nuclear Information System (INIS)

Hanson, D.J.; Ward, L.W.; Nelson, W.R.; Meyer, O.R.

1990-04-01

In support of the US Nuclear Regulatory Commission (NRC) Accident Management Research Program, a methodology has been developed for identifying the plant information needs necessary for personnel involved in the management of an accident to diagnose that an accident is in progress, select and implement strategies to prevent or mitigate the accident, and monitor the effectiveness of these strategies. This report describes the methodology and presents an application of this methodology to a Pressurized Water Reactor (PWR) with a large dry containment. A risk-important severe accident sequence for a PWR is used to examine the capability of the existing measurements to supply the necessary information. The method includes an assessment of the effects of the sequence on the measurement availability including the effects of environmental conditions. The information needs and capabilities identified using this approach are also intended to form the basis for more comprehensive information needs assessment performed during the analyses and development of specific strategies for use in accident management prevention and mitigation. 3 refs., 16 figs., 7 tabs

Accident management information needs

Energy Technology Data Exchange (ETDEWEB)

Hanson, D.J.; Ward, L.W.; Nelson, W.R.; Meyer, O.R. (EG and G Idaho, Inc., Idaho Falls, ID (USA))

1990-04-01

In support of the US Nuclear Regulatory Commission (NRC) Accident Management Research Program, a methodology has been developed for identifying the plant information needs necessary for personnel involved in the management of an accident to diagnose that an accident is in progress, select and implement strategies to prevent or mitigate the accident, and monitor the effectiveness of these strategies. This report describes the methodology and presents an application of this methodology to a Pressurized Water Reactor (PWR) with a large dry containment. A risk-important severe accident sequence for a PWR is used to examine the capability of the existing measurements to supply the necessary information. The method includes an assessment of the effects of the sequence on the measurement availability including the effects of environmental conditions. The information needs and capabilities identified using this approach are also intended to form the basis for more comprehensive information needs assessment performed during the analyses and development of specific strategies for use in accident management prevention and mitigation. 3 refs., 16 figs., 7 tabs.

Truck transportation of radioactive materials

International Nuclear Information System (INIS)

Madsen, M.M.; Wilmot, E.L.

1983-01-01

Analytical models in RADTRAN II are used to calculate risks to population subgroups such as people along transport routes, people at stops, and crewman. The stops model, which calculates the dose to persons adjacent to the transport vehicle while it is stopped, frequently provides the largest contribution to incident-free radiological impacts. Components such as distances from the vehicle containing radioactive material to nearby people at stops, stop duration, and number of crew members are required for the stops model as well as other incident-free models. To provide supporting data for RADTRAN II based on operational experience, selected truck shipments of radioactive material were observed from origin to destination. Other important aspects of this program were to correlate package size to effective shipment transport index (TI) using radiological surveys and to characterize population distributions and proximities of people to the shipment at a generic truck stop

Field Measurement of Dynamic Compressive Stress Response of Pavement-Subgrade Induced by Moving Heavy-Duty Trucks

Directory of Open Access Journals (Sweden)

Lingshi An

2018-01-01

Full Text Available This paper presents the dynamic compressive stress response of pavement-subgrade induced by moving heavy-duty trucks. In order to study the distribution characteristic of dynamic pressure of pavement-subgrade in more detail, truck loadings, truck speeds, and dynamic pressure distributions at different depths were monitored under twenty-five working conditions on the section of Qiqihar-Nenjiang Highway in Heilongjiang Province, China. The effects of truck loading, truck speed, and depth on dynamic compressive stress response can be concluded as follows: (1 increasing truck loading will increase the dynamic pressure amplitude of subgrade-pavement and dominant frequencies are close to the characteristic frequencies caused by heavy-duty trucks at the speed of 70 km/h; (2 as truck speed increases, the dynamic pressure amplitudes of measuring points have an increasing tendency; the dynamic pressure spectrums are also significantly influenced by truck speed: the higher the truck speed, the wider the spectrum and the higher the dominant frequencies; (3 as depth increases, the dynamic pressure amplitudes of measuring points decrease rapidly. The influence of the front axle decreases gradually until disappearing and the compressive stress superposition phenomenon caused by rear double axles can be found with increasing depth.

Planning of Truck Platoons: a Literature Review and Directions for Future Research

OpenAIRE

Kishore Bhoopalam, Anirudh; Agatz, Niels; Zuidwijk, Rob

2017-01-01

textabstractA truck platoon is a set of virtually linked trucks that drive closely behind one another using automated driving technology. Benefits of truck platooning include cost savings, reduced emissions, and more efficient utilization of road capacity. To fully reap these benefits in the initial phases requires careful planning of platoons based on trucks’ itineraries and time schedules. This paper provides a framework to classify various new transportation planning problems that arise in...

Evaluation of severe accident environmental conditions taking accident management strategy into account for equipment survivability assessments

International Nuclear Information System (INIS)

Lee, Byung Chul; Jeong, Ji Hwan; Na, Man Gyun; Kim, Soong Pyung

2003-01-01

This paper presents a methodology utilizing accident management strategy in order to determine accident environmental conditions in equipment survivability assessments. In case that there is well-established accident management strategy for specific nuclear power plant, an application of this tool can provide a technical rationale on equipment survivability assessment so that plant-specific and time-dependent accident environmental conditions could be practically and realistically defined in accordance with the equipment and instrumentation required for accident management strategy or action appropriately taken. For this work, three different tools are introduced; Probabilistic Safety Assessment (PSA) outcomes, major accident management strategy actions, and Accident Environmental Stages (AESs). In order to quantitatively investigate an applicability of accident management strategy to equipment survivability, the accident simulation for a most likely scenario in Korean Standard Nuclear Power Plants (KSNPs) is performed with MAAP4 code. The Accident Management Guidance (AMG) actions such as the Reactor Control System (RCS) depressurization, water injection into the RCS, the containment pressure and temperature control, and hydrogen concentration control in containment are applied. The effects of these AMG actions on the accident environmental conditions are investigated by comparing with those from previous normal accident simulation, especially focused on equipment survivability assessment. As a result, the AMG-involved case shows the higher accident consequences along the accident environmental stages

Truck acceleration behavior study and acceleration lane length recommendations for metered on-ramps

Directory of Open Access Journals (Sweden)

Guangchuan Yang

2016-10-01

Full Text Available This paper investigated the actual truck acceleration capability at metered on-ramps. Truck acceleration performance data were collected through a video-based data collection method. A piecewise constant acceleration model was employed to capture truck acceleration characteristics. It was found that the existing acceleration length will affect truck drivers’ acceleration behavior. At the taper type ramp that has limited acceleration distance, acceleration profile indicated a decreasing trend with distance. While for the ramp with an auxiliary lane that has sufficient acceleration distance, it was found that the acceleration behavior is to have a high acceleration rate in the beginning, then acceleration rate decrease with speed increase, and high acceleration rate again as drivers approach the merging area. Field data show that the truck acceleration performance data documented in the ITE’s (Institute of Transportation Engineers “Traffic Engineering Handbook” are much lower than the field collected data. Also, based on the regression analysis of speed versus distance profiles, it was found that the AASHTO’s (American Association of State Highway and Transportation Officials Green Book acceleration length design guidance is insufficient to accommodate trucks at metered on-ramps. The required acceleration lengths for medium and heavy trucks are approximately 1.3 and 1.6 times of the Green Book design guideline, respectively.

Truck and rail charges for shipping spent fuel and nuclear waste

International Nuclear Information System (INIS)

McNair, G.W.; Cole, B.M.; Cross, R.E.; Votaw, E.F.

1986-06-01

The Pacific Northwest Laboratory developed techniques for calculating estimates of nuclear-waste shipping costs and compiled a listing of representative data that facilitate incorporation of reference shipping costs into varius logistics analyses. The formulas that were developed can be used to estimate costs that will be incurred for shipping spent fuel or nuclear waste by either legal-weight truck or general-freight rail. The basic data for this study were obtained from tariffs of a truck carrier licensed to serve the 48 contiguous states and from various rail freight tariff guides. Also, current transportation regulations as issued by the US Department of Transportation and the Nuclear Regulatory Commission were investigated. The costs that will be incurred for shipping spent fuel and/or nuclear waste, as addressed by the tariff guides, are based on a complex set of conditions involving the shipment origin, route, destination, weight, size, and volume and the frequency of shipments, existing competition, and the length of contracts. While the complexity of these conditions is an important factor in arriving at a ''correct'' cost, deregulation of the transportation industry means that costs are much more subject to negotiation and, thus, the actual fee that will be charged will not be determined until a shipping contract is actually signed. This study is designed to provide the baseline data necessary for making comparisons of the estimated costs of shipping spent fuel and/or nuclear wastes by truck and rail transportation modes. The scope of the work presented in this document is limited to the costs incurred for shipping, and does not include packaging, cask purchase/lease costs, or local fees placed on shipments of radioactive materials

Roadmap and technical white papers for the 21st century truck partnership

Energy Technology Data Exchange (ETDEWEB)

None, None

2006-12-01

21st Century Truck Partnership will support the development and implementation of technologies that will cut fuel use and emissions and enhance safety, affordability, and performance of trucks and buses.

Evaluation of an accident management strategy of emergency water injection using fire engines in a typical pressurized water reactor

Directory of Open Access Journals (Sweden)

Soo-Yong Park

2015-10-01

Full Text Available Following the Fukushima accident, a special safety inspection was conducted in Korea. The inspection results show that Korean nuclear power plants have no imminent risk for expected maximum potential earthquake or coastal flooding. However long- and short-term safety improvements do need to be implemented. One of the measures to increase the mitigation capability during a prolonged station blackout (SBO accident is installing injection flow paths to provide emergency cooling water of external sources using fire engines to the steam generators or reactor cooling systems. This paper illustrates an evaluation of the effectiveness of external cooling water injection strategies using fire trucks during a potential extended SBO accident in a 1,000 MWe pressurized water reactor. With regard to the effectiveness of external cooling water injection strategies using fire engines, the strategies are judged to be very feasible for a long-term SBO, but are not likely to be effective for a short-term SBO.

Evaluation of an accident management strategy of emergency water injection using fire engines in a typical pressurized water reactor

International Nuclear Information System (INIS)

Park, Soo Yong; Ahn, Kwang Il

2015-01-01

Following the Fukushima accident, a special safety inspection was conducted in Korea. The inspection results show that Korean nuclear power plants have no imminent risk for expected maximum potential earthquake or coastal flooding. However long- and short-term safety improvements do need to be implemented. One of the measures to increase the mitigation capability during a prolonged station blackout (SBO) accident is installing injection flow paths to provide emergency cooling water of external sources using fire engines to the steam generators or reactor cooling systems. This paper illustrates an evaluation of the effectiveness of external cooling water injection strategies using fire trucks during a potential extended SBO accident in a 1,000 MWe pressurized water reactor. With regard to the effectiveness of external cooling water injection strategies using fire engines, the strategies are judged to be very feasible for a long-term SBO, but are not likely to be effective for a short-term SBO

Evaluation of an accident management strategy of emergency water injection using fire engines in a typical pressurized water reactor

Energy Technology Data Exchange (ETDEWEB)

Park, Soo Yong; Ahn, Kwang Il [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

Following the Fukushima accident, a special safety inspection was conducted in Korea. The inspection results show that Korean nuclear power plants have no imminent risk for expected maximum potential earthquake or coastal flooding. However long- and short-term safety improvements do need to be implemented. One of the measures to increase the mitigation capability during a prolonged station blackout (SBO) accident is installing injection flow paths to provide emergency cooling water of external sources using fire engines to the steam generators or reactor cooling systems. This paper illustrates an evaluation of the effectiveness of external cooling water injection strategies using fire trucks during a potential extended SBO accident in a 1,000 MWe pressurized water reactor. With regard to the effectiveness of external cooling water injection strategies using fire engines, the strategies are judged to be very feasible for a long-term SBO, but are not likely to be effective for a short-term SBO.

Analysis of frame structure of medium and small truck crane

Science.gov (United States)

Cao, Fuyi; Li, Jinlong; Cui, Mengkai

2018-03-01

Truck crane is an important part of hoisting machinery. Frame, as the support component of the quality of truck crane, determines the safety of crane jib load and the rationality of structural design. In this paper, the truck crane frame is a box structure, the three-dimensional model is established in CATIA software, and imported into Hyperworks software for finite element analysis. On the base of doing constraints and loads for the finite element model of the frame, the finite element static analysis is carried out. And the static stress test verifies whether the finite element model and the frame structure design are reasonable; then the free modal analysis of the frame and the analysis of the first 8 - order modal vibration deformation are carried out. The analysis results show that the maximum stress value of the frame is greater than the yield limit value of the material, and the low-order modal value is close to the excitation frequency value, which needs to be improved to provide theoretical reference for the structural design of the truck crane frame.

Improving the system of warranty service of trucks in foreign markets

Directory of Open Access Journals (Sweden)

Irina MAKAROVA

2015-03-01

Full Text Available The article is devoted to the practical methods development of improving one of the ways to ensure the health of trucks in the system warranty. Methodology is aimed at optimizing the processes of formation of warranty spare parts kits during the implementation of KAMAZ trucks in foreign markets. The example is given to demonstrate the importance of different factors in the formation of the warranty set for different regions. The algorithm was developed to assess the qualitative composition formed warranty package that will optimize the planning and organization of activity centers to improve operational reliability of commercial trucks. A basis for acceptance of the scientifically-proved decisions is the statistical data analysis of requests monitoring that allows organizing duly replacement of parts with expired service life, and also promotes customer servicing quality improvement and reliability of trucks by prevention of its failures.

Regulatory approach to accident management in Sweden

International Nuclear Information System (INIS)

Hoegberg, L.

1989-01-01

The Swedish accident management program includes the following components: definition of overall safety and radiation protection objectives for the program; definition of appropriate accident management strategies to reach these objectives, based on plant-specific severe accident analysis; development and installation of appropriate accident management systems and associated management procedure; definition of roles and resposibilities for plant staff involved in accident management and implementation of appropriate training programs. The discussion of these components tries to highlight the basic technical concepts and approaches and the underlying safety philosophy rather than going into design details. 5 figs., 7 refs

Uranium storage bed accident hazards evaluation

International Nuclear Information System (INIS)

Longhurst, G.R.; Shmayda, W.T.

1989-01-01

To properly assess hazards and risks associated with the use of uranium beds as tritium storage devices in fusion reactor systems, it is necessary to understand the consequences occurring in the event of an accident. Accidents involving uranium beds are postulated, and the possible results are considered. A research program to more fully and accurately understand those results has been initiated involving the Idaho National Engineering Laboratory and Ontario Hydro. The plan and objectives of that program are presented. 11 refs., 1 tab

Uranium storage bed accident hazards evaluation

International Nuclear Information System (INIS)

Longhurst, G.R.; Shmayda, W.T.

1989-10-01

To properly assess hazards and risks associated with the use of uranium beds as tritium storage devices in fusion reactor systems, it is necessary to understand the consequences occurring in the event of an accident. Accidents involving uranium beds are postulated, and the possible results are considered. A research program to more fully and accurately understand those results has been initiated involving the Idaho National Engineering Laboratory and Ontario Hydro. The plan and objectives of that program are presented. 11 refs., 1 tab

REAC/TS Radiation Accident Registry: An Overview

Energy Technology Data Exchange (ETDEWEB)

Doran M. Christensen, DO, REAC/TS Associate Director and Staff Physician Becky Murdock, REAC/TS Registry and Health Physics Technician

2012-12-12

Over the past four years, REAC/TS has presented a number of case reports from its Radiation Accident Registry. Victims of radiological or nuclear incidents must meet certain dose criteria for an incident to be categorized as an “accident” and be included in the registry. Although the greatest numbers of “accidents” in the United States that have been entered into the registry involve radiation devices, the greater percentage of serious accidents have involved sealed sources of one kind or another. But if one looks at the kinds of accident scenarios that have resulted in extreme consequence, i.e., death, the greater share of deaths has occurred in medical settings.

Occupational accidents among mototaxi drivers.

Science.gov (United States)

Amorim, Camila Rego; de Araújo, Edna Maria; de Araújo, Tânia Maria; de Oliveira, Nelson Fernandes

2012-03-01

The use of motorcycles as a means of work has contributed to the increase in traffic accidents, in particular, mototaxi accidents. The aim of this study was to estimate and characterize the incidence of occupational accidents among the mototaxis registered in Feira de Santana, BA. This is a cross-sectional study with descriptive and census data. Of the 300 professionals registered at the Municipal Transportation Service, 267 professionals were interviewed through a structured questionnaire. Then, a descriptive analysis was conducted and the incidence of accidents was estimated based on the variables studied. Relative risks were calculated and statistical significance was determined using the chi-square test and Fisher's exact test, considering p accidents were observed in 10.5% of mototaxis. There were mainly minor injuries (48.7%), 27% of them requiring leaves of absence from work. There was an association between the days of work per week, fatigue in lower limbs and musculoskeletal complaints, and accidents. Knowledge of the working conditions and accidents involved in this activity can be of great importance for the adoption of traffic education policies, and to help prevent accidents by improving the working conditions and lives of these professionals.

Multistage Mechanical Transmissions with Automatic Control for Advanced Trucks and Buses

Directory of Open Access Journals (Sweden)

Blokhin Aleksandr

2017-12-01

Full Text Available The study considers the basic trends of development of modern mechanical transmissions of trucks and buses. It provides the developed various series of multispeed transmissions with automatic control and a number of transmissions from 6 to 16 for trucks and buses. The paper shows the basic parameters of the standard series of new transmissions received on the basis of innovative technical solutions. It provides the results of experimental studies of 16-speed transmissions on a special test stand and on the road as part of a truck transmission. Theoretical and experimental data on the gear change time are compared.

Assessment of uncertainties in severe accident management strategies

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Catton, I.; Dhir, V.K.; Okrent, D.

1990-01-01

Recent progress on the development of Probabilistic Risk Assessment (PRA) as a tool for qualifying nuclear reactor safety and on research devoted to severe accident phenomena has made severe accident management an achievable goal. Severe accident management strategies may involve operational changes, modification and/or addition of hardware, and institutional changes. In order to achieve the goal of managing severe accidents, a method for assessment of strategies must be developed which integrates PRA methodology and our current knowledge concerning severe accident phenomena, including uncertainty. The research project presented in this paper is aimed at delineating uncertainties in severe accident progression and their impact on severe accident management strategies

Carbon monoxide poisoning in children riding in the back of pickup trucks.

Science.gov (United States)

Hampson, N B; Norkool, D M

OBJECTIVE - To describe the case characteristics of a series of children poisoned with carbon monoxide while traveling in the back of pickup trucks. DESIGN - Pediatric cases referred for treatment of carbon monoxide poisoning with hyperbaric oxygen between 1986 and 1991 were reviewed. Those cases that occurred during travel in the back of pickup trucks were selected. Clinical follow-up by telephone interview ranged from 2 to 55 months. SETTING - A private, urban, tertiary care center in Seattle, Wash. PATIENTS - Twenty children ranging from 4 to 16 years of age. INTERVENTION - All patients were treated with hyperbaric oxygen. MAIN OUTCOME MEASURES - Characteristics of the poisoning incident and clinical patient outcome. RESULTS - Of 68 pediatric patients treated for accidental carbon monoxide poisoning, 20 cases occurred as children rode in the back of pickup trucks. In 17 of these, the children were riding under a rigid closed canopy on the rear of the truck, while three episodes occurred as children rode beneath a tarpaulin. Average carboxyhemoglobin level on emergency department presentation was 18.2% +/- 2.4% (mean +/- SEM; range, 1.6% to 37.0%). Loss of consciousness occurred in 15 of the 20 children. One child died of cerebral edema, one had permanent neurologic deficits, and 18 had no recognizable sequelae related to the episode. In all cases, the truck exhaust system had a previously known leak or a tail pipe that exited at the rear rather than at the side of the pickup truck. CONCLUSIONS - Carbon monoxide poisoning is a significant hazard for children who ride in the back of pickup trucks. If possible, this practice should be avoided.

In-depth analysis of urban accidents involving motorcycle and moped riders in France, construction of prototypical accident scenarios and prospects for their prevention

OpenAIRE

CLABAUX, N

2007-01-01

owered two-wheeler users constitute, with cyclists and pedestrians, a category of road users who are particularly vulnerable in case of accident, since the slightest impact exposes them to injury. The recent and actual growth in the use of powered two-wheelers in France, notably in urban areas, and the over-representation of this category of road users in injury accidents show the need for a better understanding of motorcycle and moped accident phenomena in order to define new countermeasures...

Severe accident management: radiation dose control, Fukushima Daiichi and TMI-2 nuclear plant accidents

International Nuclear Information System (INIS)

Shaw, Roger

2014-01-01

This presentation presents valuable dose information related to the Fukushima Daiichi and Three Mile Island Unit 2 (TMI-2) Nuclear Plant accidents. Dose information is provided for what is well known for TMI-2, and what is available for Fukushima Daiichi. Particular emphasis is placed on the difference between the type of reactors involved, overarching plant damage issues, and radiation worker dose outcomes. For TMI-2, more in depth dose data is available for the accident and the subsequent recovery efforts. The comparisons demonstrate the need to understand the wide variation in potential dose management measures and outcomes for severe reactor accidents. (author)

Key Characteristics of Combined Accident including TLOFW accident for PSA Modeling

Energy Technology Data Exchange (ETDEWEB)

Kim, Bo Gyung; Kang, Hyun Gook [KAIST, Daejeon (Korea, Republic of); Yoon, Ho Joon [Khalifa University of Science, Technology and Research, Abu Dhabi (United Arab Emirates)

2015-05-15

The conventional PSA techniques cannot adequately evaluate all events. The conventional PSA models usually focus on single internal events such as DBAs, the external hazards such as fire, seismic. However, the Fukushima accident of Japan in 2011 reveals that very rare event is necessary to be considered in the PSA model to prevent the radioactive release to environment caused by poor treatment based on lack of the information, and to improve the emergency operation procedure. Especially, the results from PSA can be used to decision making for regulators. Moreover, designers can consider the weakness of plant safety based on the quantified results and understand accident sequence based on human actions and system availability. This study is for PSA modeling of combined accidents including total loss of feedwater (TLOFW) accident. The TLOFW accident is a representative accident involving the failure of cooling through secondary side. If the amount of heat transfer is not enough due to the failure of secondary side, the heat will be accumulated to the primary side by continuous core decay heat. Transients with loss of feedwater include total loss of feedwater accident, loss of condenser vacuum accident, and closure of all MSIVs. When residual heat removal by the secondary side is terminated, the safety injection into the RCS with direct primary depressurization would provide alternative heat removal. This operation is called feed and bleed (F and B) operation. Combined accidents including TLOFW accident are very rare event and partially considered in conventional PSA model. Since the necessity of F and B operation is related to plant conditions, the PSA modeling for combined accidents including TLOFW accident is necessary to identify the design and operational vulnerabilities.The PSA is significant to assess the risk of NPPs, and to identify the design and operational vulnerabilities. Even though the combined accident is very rare event, the consequence of combined

Bus accident severity and passenger injury: evidence from Denmark

DEFF Research Database (Denmark)

Prato, Carlo Giacomo; Kaplan, Sigal

2014-01-01

Purpose Bus safety is a concern not only in developing countries, but also in the U.S. and Europe. In Denmark, disentangling risk factors that are positively or negatively related to bus accident severity and injury occurrence to bus passengers can contribute to promote safety as an essential...... principle of sustainable transit and advance the vision “every accident is one too many”. Methods Bus accident data were retrieved from the national accident database for the period 2002–2011. A generalized ordered logit model allows analyzing bus accident severity and a logistic regression enables...... examining occurrence of injury to bus passengers. Results Bus accident severity is positively related to (i) the involvement of vulnerable road users, (ii) high speed limits, (iii) night hours, (iv) elderly drivers of the third party involved, and (v) bus drivers and other drivers crossing in yellow or red...

Review of progress on enhanced accident tolerant fuel

International Nuclear Information System (INIS)

McCoy, K.; Dunn, B.; Kochendarfer, R.

2015-01-01

The accident at Fukushima has resulted in renewed interest in understanding the performance of nuclear power plants under accident conditions. Part of that interest is directed toward determining how to improve the performance of fuel during an accident that involves long exposures of the fuel to high temperatures. This paper describes the method being used by AREVA to select and evaluate approaches for improving the accident tolerance of nuclear fuel. The method involves starting with a large number of approaches that might enhance accident tolerance, and reviewing how well each approach satisfies a set of engineering requirements and goals. Among the approaches investigated we have the development of fuel pellets that contain a second phase to improve thermal conductivity, the use of molybdenum alloy tubing as fuel cladding, the use of oxidation-resistant coatings to zirconium cladding, and the use of nanoparticles in the coolant to improve heat transfer

Feasibility study on the formation of a databank of the arrangements within the European Community for transport accidents involving radioactive materials. Phase 1

International Nuclear Information System (INIS)

Hugues, J.S.; Shaw, K.B.

1989-01-01

Radioactive materials are transported throughout the European Communities (EC) by road, rail, sea and air. In case of severe accident, which could lead to the release of radioactivity into the environment, it is essential that there are pre-arranged measures which can be put into effect to minimise radiation doses to persons in the vicinity and to enable the situation to be returned to a safe condition. An essential part of emergency arrangements is the setting up of an administrative structure to establish the responsibilities of the organisations involved and this study outlines the arrangements that have been set up in each EC country. The databank should be particularly useful following an accident close to a national border or in the event of an accident in one country which involves a shipment from another. The setting up of a databank might also assist in the development of the emergency arrangements in some countries. In conclusion: - the formation of a databank of emergency arrangements is feasible. - The databank could be operated more efficiently if it were held centrally on a computed-based system and made accessible through the telephone network. - The usefulness of the databank would be enhanced by the inclusion of information on non-radiological hazards

Exploring Environmental Effects of Accidents During Marine Transport of Dangerous Goods by Use of Accident Descriptions

DEFF Research Database (Denmark)

Rømer, Hans Gottberg; Haastrup, P.; Petersen, H J Styhr

1996-01-01

On the basis of 1776 descriptions of water transport accidents involving dangerous goods, environmental problems in connection with releases of this kind are described and discussed. It was found that most detailed descriptions of environmental consequences concerned oil accidents, although most...... longer than broad. Gravity scales used to describe and evaluate environmental consequences were discussed....

The Production Measurement Model of Open Pit Mine Based on Truck Operation Diagram

Directory of Open Access Journals (Sweden)

Sun Xiao-Yu

2016-01-01

Full Text Available Conventional production measurement of truck dispatching system in open pit mine has not been effectively expressed by a mathematical model, which brings a negative effect on the subsequent data mining and a compatibility issue to apply the production measurement with fixed assignment of truck. In this study, based on the proposed concept that truck is not only the carrier of transport material, but also act as the bridges and linkages between the loading sites and the unloading sites, a new truck operation diagram was established, which was further developed to a basic data matrix and a production measurement model. The new model allowed to calculatethe production measurement of the transport, loading, unloading, material and etc, respectively, as well as with any calculation in combination of more than one factor as needed.It solved the compatibility issue between conventional production measurement and the production measurement of fixed assignment of truck with good practical results.

STRESS LOADING SIMULATION OF HYDRO-MECHANICAL TRANSMISSION OF DUMP TRUCK

Directory of Open Access Journals (Sweden)

S. A. Sidorov

2006-01-01

Full Text Available The Transmission model and software package to investigate stress loading of a hydromechanical transmission of a dump truck have been developed. The given software package allows to model stress loading of transmission gears in taking-off and acceleration modes at various road resistance, positions of an engine control pedal and initial revolutions of an engine crankshaft, various laws of friction clutch switching and some other parameters that permit to reveal a rate of various operational mode influence on stress loading of a dump truck transmission. An equivalence of the developed software is proved by the comparison of the experimentally obtained stress loading process of the hydro-mechanical transmission of a BelAZ- 7555 dump truck with the results of the simulation 

The Radiological Accident in Lia, Georgia

Energy Technology Data Exchange (ETDEWEB)

NONE

2014-12-15

The use of radioactive material offers a wide range of benefits to medicine, research and industry throughout the world. Precautions are necessary, however, to limit the exposure of people to the radiation emitted. Where the amount of radioactive material is substantial, as in the case of radiotherapy or industrial radiography sources, great care is required to prevent accidents which could have severe consequences. Nevertheless, in spite of the precautions taken, serious accidents involving radiation sources continue to occur, albeit infrequently. The IAEA conducts follow-up reviews of such serious accidents to provide an account of their circumstances and consequences, from which organizations with responsibilities for radiation protection, safety of sources and emergency preparedness and response may learn. A serious radiological accident occurred in Georgia on 2 December 2001, when three inhabitants of the village of Lia found two metal objects in the forest while collecting firewood. These objects were {sup 90}Sr sources with an activity of 1295 TBq. The three inhabitants used the objects as heaters when spending the night in the forest. The major cause of the accident was the improper and unauthorized abandonment of radiation sources in Georgia and the absence of clear labels or radiation signs on the sources warning of the potential radiation hazard. Under the Convention on Assistance in the Case of a Nuclear Accident or Radiological Emergency (Assistance Convention), the Georgian authorities requested assistance from the IAEA to advise on the dose assessment, source recovery and medical management of those involved in the accident. This publication describes the circumstances and events surrounding the accident, its management and the medical treatment of the people exposed. It also describes the dose reconstruction calculations and biodosimetry assessments conducted. A number of uncertainties remain relating to some details of the accident. However

The Radiological Accident in Lia, Georgia

International Nuclear Information System (INIS)

2014-12-01

The use of radioactive material offers a wide range of benefits to medicine, research and industry throughout the world. Precautions are necessary, however, to limit the exposure of people to the radiation emitted. Where the amount of radioactive material is substantial, as in the case of radiotherapy or industrial radiography sources, great care is required to prevent accidents which could have severe consequences. Nevertheless, in spite of the precautions taken, serious accidents involving radiation sources continue to occur, albeit infrequently. The IAEA conducts follow-up reviews of such serious accidents to provide an account of their circumstances and consequences, from which organizations with responsibilities for radiation protection, safety of sources and emergency preparedness and response may learn. A serious radiological accident occurred in Georgia on 2 December 2001, when three inhabitants of the village of Lia found two metal objects in the forest while collecting firewood. These objects were 90 Sr sources with an activity of 1295 TBq. The three inhabitants used the objects as heaters when spending the night in the forest. The major cause of the accident was the improper and unauthorized abandonment of radiation sources in Georgia and the absence of clear labels or radiation signs on the sources warning of the potential radiation hazard. Under the Convention on Assistance in the Case of a Nuclear Accident or Radiological Emergency (Assistance Convention), the Georgian authorities requested assistance from the IAEA to advise on the dose assessment, source recovery and medical management of those involved in the accident. This publication describes the circumstances and events surrounding the accident, its management and the medical treatment of the people exposed. It also describes the dose reconstruction calculations and biodosimetry assessments conducted. A number of uncertainties remain relating to some details of the accident. However, sufficient

Accidents involving Brazilian indigenous treated at urgent and emergency services of the Unified Health System.

Science.gov (United States)

Souza, Edinilsa Ramos de; Njaine, Kathie; Mascarenhas, Márcio Dênis Medeiros; Oliveira, Maria Conceição de

2016-12-01

Abstract We analyzed the accidents with Brazilian indigenous treated at urgent and emergency services of the Unified Health System (SUS). Data were obtained from the 2014 Viva Survey, which included 86 services from 24 capitals and the Federal District. The demographic profile of the indigenous, the event and the attendance were characterized. Most of the attended people were male in the 20-39 years age group. Falls and traffic accidents were the main reasons for attendance. Alcohol use was informed by 5.6% of the attended people, a figure that increases to 19.1% in traffic accidents, 26.1% among drivers and 22.8% among motorcyclists. There was a statistical difference between genders in relation to age, disability, place of occurrence of the event, work-related event and victim's condition in the traffic accident. We emphasize the importance of providing visibility to accidents with indigenous and engage them in the prevention of such events. Data reliability depends on the adequate completion in indigenous health information systems.

In-Plant Fission Product Behavior in SGTR Accident with Long-Term SBO

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae Woon; Han, Seok Jung; Ahn, Kwang Il [KAERI, Daejeon (Korea, Republic of)

2015-05-15

The off-site AC power was recovered in 9 days after the accident in the NPS. Therefore safety injection by fire pump truck with fresh water or seawater is only available in the Fukushima accident. However, safety injection by fire pump truck is not always effective due to the high pressure of RPV inside or leakages of alternative water injection flow paths. In the SBO situations in pressurized water reactor plant (PWR), turbine driven auxiliary feedwater (TD-AFW) pump can inject water to the secondary side of steam generator. However, turbine inlet steam flow control valve cannot work properly when loss of vital DC power occurs. Vital DC power is designed to be maintained during 4 or 8 hours in the SBO conditions. In this paper motor-driven and turbine driven AFW pumps are all assumed to be not working at time 0 sec as a worst case assumption. Iodine pool-scrubbing can occur in the secondary side of the faulted steam generator. However, iodine pool-scrubbing in the secondary side of the faulted steam generator is assumed not to be working, due to the assumption of the loss of DC battery for turbine inlet flow control valve. Iodine pool-scrubbing is one of the long-term research issues in safety assessment of nuclear power plant severe accident. PHEBUS FPT series and THAI experiment projects are typical projects on the resolving source term issues in severe accident of nuclear power plants. However, iodine retention by pool scrubbing is still a debating issue. In such containment bypass sequences, fission products can be released out to environment directly from RCS without retention or deposition in containment structures. SGTR is one of the hazardous accident scenarios in the typical PSA, because SGTR induces a large release amount of source term to environment directly. A key operation strategy was the isolation of the broken reactor coolant system loop from the intact loop. Typical core degradation in SGTR scenarios occurs with multiple failures of the isolation

Accident selection methodology for TA-55 FSAR

International Nuclear Information System (INIS)

Letellier, B.C.; Pan, P.Y.; Sasser, M.K.

1995-01-01

In the past, the selection of representative accidents for refined analysis from the numerous scenarios identified in hazards analyses (HAs) has involved significant judgment and has been difficult to defend. As part of upgrading the Final Safety Analysis Report (FSAR) for the TA-55 plutonium facility at the Los Alamos National Laboratory, an accident selection process was developed that is mostly mechanical and reproducible in nature and fulfills the requirements of the Department of Energy (DOE) Standard 3009 and DOE Order 5480.23. Among the objectives specified by this guidance are the requirements that accident screening (1) consider accidents during normal and abnormal operating conditions, (2) consider both design basis and beyond design basis accidents, (3) characterize accidents by category (operational, natural phenomena, etc.) and by type (spill, explosion, fire, etc.), and (4) identify accidents that bound all foreseeable accident types. The accident selection process described here in the context of the TA-55 FSAR is applicable to all types of DOE facilities

Toxoplasma gondii infection in interstate truck drivers: a case-control seroprevalence study.

Science.gov (United States)

Alvarado-Esquivel, Cosme; Pacheco-Vega, Sandy Janet; Hernández-Tinoco, Jesús; Salcedo-Jáquez, Misael; Sánchez-Anguiano, Luis Francisco; Berumen-Segovia, Luis Omar; Rábago-Sánchez, Elizabeth; Liesenfeld, Oliver

2015-02-05

Infection with Toxoplasma gondii can be acquired via the ingestion of undercooked or raw meat containing tissue cysts, or via ingestion of water contaminated with oocysts. Professional long distance truck driving may have epidemiological importance for food-borne infections since drivers eat out of home and in places where hygiene and cooking practices are uncertain. We aimed to determine whether interstate truck drivers in Durango, Mexico have an increased risk of infection with T. gondii as indicated by seropositivity; and to determine the socio-demographic, work, clinical, and behavioral characteristics associated with T. gondii seropositivity in interstate truck drivers. Through a case-control study design, 192 truck drivers and 192 controls from the general population of the same region matched by gender and age were examined with enzyme-linked immunoassays for the presence of anti-Toxoplasma IgG and IgM antibodies. Socio-demographic, work, clinical and behavioral characteristics from the truck drivers were obtained. Anti-T. gondii IgG antibodies were found in 23 (12.0%) of 192 truck drivers and in 13 (6.8%) of 192 controls (OR = 21.0; 95% CI: 1.23-358.38; P = 0.002). Anti-T. gondii IgM antibodies were found in 7 (3.6%) cases and in 7 (3.6%) controls (P = 1.00). The seroprevalence of T. gondii infection was higher in drivers with reflex impairment than in those without this impairment (4/13, 30.8% vs 19/179, 10.6%, respectively; P = 0.05), and in drivers with hearing impairment than in those without this impairment (3/7, 42.9% vs 20/185, 10.8%, respectively; P = 0.03). Multivariate analysis of work and behavioral characteristics of truck drives showed positive associations of T. gondii exposure with trips to the south of Mexico (OR = 3.11; 95% CI: 1.02-9.44; P = 0.04) and consumption of horse meat (OR = 5.18; 95% CI: 1.62-16.55; P = 0.005). Results suggest that interstate truck drivers may have an increased risk for T

Effects of After-Treatment Control Technologies on Heavy-Duty Diesel Truck Emissions

Science.gov (United States)

Preble, C.; Dallmann, T. R.; Kreisberg, N. M.; Hering, S. V.; Harley, R.; Kirchstetter, T.

2015-12-01

Diesel engines are major emitters of nitrogen oxides (NOx) and the black carbon (BC) fraction of particulate matter (PM). Diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have recently become standard on new heavy-duty diesel trucks (HDDT). There is concern that DPFs may increase ultrafine particle (UFP) and total particle number (PN) emissions while reducing PM mass emissions. Also, the deliberate catalytic oxidation of engine-out NO to NO2 in continuously regenerating DPFs may lead to increased tailpipe emission of NO2 and near-roadway concentrations that exceed the 1-hr national ambient air quality standard. Increased NO2 emissions can also promote formation of ozone and secondary PM. We report results from ongoing on-road studies of HDDT emissions at the Port of Oakland and the Caldecott Tunnel in California's San Francisco Bay Area. Emission factors (g pollutant per kg diesel) were linked via recorded license plates to each truck's engine model year and installed emission controls. At both sites, DPF use significantly increased the NO2/NOx emission ratio. DPFs also significantly increased NO2 emissions when installed as retrofits on older trucks with higher baseline NOx emissions. While SCR systems on new trucks effectively reduce total NOx emissions and mitigate these undesirable DPF-related NO2 emissions, they also lead to significant emission of N2O, a potent greenhouse gas. When expressed on a CO2-equivalent basis, the N2O emissions increase offsets the fuel economy gain (i.e., the CO2 emission reduction) associated with SCR use. At the Port, average NOx, BC and PN emission factors from new trucks equipped with DPF and SCR were 69 ± 15%, 92 ± 32% and 66 ± 35% lower, respectively, than modern trucks without these emission controls. In contrast, at the Tunnel, PN emissions from older trucks retrofit with DPFs were ~2 times greater than modern trucks without DPFs. The difference

Safety demonstration analyses for severe accident of fresh nuclear fuel transport packages at JAERI

International Nuclear Information System (INIS)

Yamada, K.; Watanabe, K.; Nomura, Y.; Okuno, H.; Miyoshi, Y.

2004-01-01

It is expected in the near future that more and more fresh nuclear fuel will be transported in a variety of transport packages to cope with increasing demand from nuclear fuel cycle facilities. Accordingly, safety demonstration analyses of these methods are planned and conducted at JAERI under contract with the Ministry of Economy, Trade and Industry of Japan. These analyses are conducted part of a four year plan from 2001 to 2004 to verify integrity of packaging against leakage of radioactive material in the case of a severe accident envisioned to occur during transportation, for the purpose of gaining public acceptance of such nuclear fuel activities. In order to create the accident scenarios, actual transportation routes were surveyed, accident or incident records were tracked, international radioactive material transport regulations such as IAEA rules were investigated and, thus, accident conditions leading to mechanical damage and thermal failure were selected for inclusion in the scenario. As a result, the worst-case conditions of run-off-the-road accidents were incorporated, where there is impact against a concrete or asphalt surface. Fire accidents were assumed to occur after collision with a tank truck carrying lots of inflammable material or destruction by fire after collision inside a tunnel. The impact analyses were performed by using three-dimensional elements according to the general purpose impact analysis code LS-DYNA. Leak-tightness of the package was maintained even in the severe impact accident scenario. In addition, the thermal analyses were performed by using two-dimensional elements according to the general purpose finite element method computer code ABAQUS. As a result of these analyses, the integrity of the inside packaging component was found to be sufficient to maintain a leak-tight state, confirming its safety

Progress in methodology for probabilistic assessment of accidents: timing of accident sequences

International Nuclear Information System (INIS)

Lanore, J.M.; Villeroux, C.; Bouscatie, F.; Maigret, N.

1981-09-01

There is an important problem for probabilistic studies of accident sequences using the current event tree techniques. Indeed this method does not take into account the dependence in time of the real accident scenarios, involving the random behaviour of the systems (lack or delay in intervention, partial failures, repair, operator actions ...) and the correlated evolution of the physical parameters. A powerful method to perform the probabilistic treatment of these complex sequences (dynamic evolution of systems and associated physics) is Monte-Carlo simulation, very rare events being treated with the help of suitable weighting and biasing techniques. As a practical example the accident sequences related to the loss of the residual heat removal system in a fast breeder reactor has been treated with that method

Analytical solution to energy management guaranteeing battery life for hybrid trucks

NARCIS (Netherlands)

Pham, H.T.; Kessels, J.T.B.A.; van den Bosch, P.P.J.; Huisman, R.G.M.

2016-01-01

This paper considers a parallel hybrid electric truck where the tractive force delivered to the wheels can be provided by a conventional internal combustion engine (ICE) and/or a motor generator (MG). This hybrid truck is equipped with a clutch system that is capable of decoupling the ICE and the MG

An innovative food truck chain, strategic planning inspired from the lean start up methodology

OpenAIRE

Peñate, Paul Tavares

2015-01-01

Mestardo em Marketing Suportada pela abordagem Lean , o Projecto apresenta um modelo de negócios de uma nova marca de Food Truck, inicialmente a ser lançada na Bélgca. Foodies’TruckZ é a marca sugerida para um novo modelo de negócio de Food Truck que procura inovar alavancando economias de escala, sobretudo em Marketing, e através de uma frota co-propriedade das carinhas food truck. Neste modelo de negócio a partilha no investimento do camião, na comunicação e outros aspectos de marketing ...

Accidents in the construction industry in the Netherlands: An analysis of accident reports using Storybuilder

International Nuclear Information System (INIS)

Ale, B.J.M.; Bellamy, L.J.; Baksteen, H.; Damen, M.; Goossens, L.H.J.; Hale, A.R.; Mud, M.; Oh, J.; Papazoglou, I.A.; Whiston, J.Y.

2008-01-01

As part of an ongoing effort by the Ministry of Social Affairs and Employment of the Netherlands, a research project is being undertaken to construct a causal model for occupational risk. This model should provide quantitative insight into the causes and consequences of occupational accidents. One of the components of the model is a tool to systematically classify and analyse reports of past accidents. This tool 'Storybuilder' was described in earlier papers. In this paper, Storybuilder is used to analyse the causes of accidents reported in the database of the Dutch Labour Inspectorate involving people working in the construction industry. Conclusions are drawn on measures to reduce the accident probability. Some of these conclusions are contrary to common beliefs in the industry

Technology Roadmap for the 21st Century Truck Program, a government-industry research partnership

Energy Technology Data Exchange (ETDEWEB)

None

2000-12-01

The 21st Century Truck Program has been established as a government-industry research partnership to support the development and implementation of commercially viable technologies that will dramatically cut fuel use and emissions of commercial trucks and buses while enhancing their safety and affordability as well as maintaining or enhancing performance. The innovations resulting from this program will reduce dependence on foreign oil, improve our nation's air quality, provide advanced technology for military vehicles, and enhance the competitiveness of the U.S. truck and bus industry while ensuring safe and affordable freight and bus transportation for the nation's economy. This Technology Roadmap for the 21st Century Truck Program has been prepared to guide the development of the technical advancements that will enable the needed improvements in commercial truck fuel economy, emissions, and safety.

Truck side guard specifications : recommended standard

Science.gov (United States)

2016-09-01

This document is intended to be used by (1) public or private medium/heavy-duty truck fleets considering adding side guards; (2) jurisdictions or customers that require side guards through policy or procurement; (3) manufacturers of side guards; and ...

Road accidents caused by sleepy drivers: Update of a Norwegian survey.

Science.gov (United States)

Phillips, Ross Owen; Sagberg, Fridulv

2013-01-01

The current study tests, updates and expands a model of factors associated with sleepy driving, originally based on a 1997 survey of accident-involved Norwegian drivers (Sagberg, F., 1999. Road accidents caused by drivers falling asleep. Accident Analysis & Prevention 31, 639-649). The aim is to establish a robust model to inform measures to tackle sleepy driving. The original questions on (i) tiredness-related accidents and (ii) incidents of sleep behind the wheel in the last 12 months were again posed in 2003 and 2008, in independent surveys of Norwegian drivers involved in accidents reported to a large insurance company. According to those drivers at-fault for the accident, tiredness or sleepiness behind the wheel contributed to between 1.9 and 3.9 per cent of all types of accident reported to the insurance company across these years. Accident-involved drivers not at fault for the accident reported a reduction in the incidence of sleep behind the wheel for the preceding year, decreasing from 8.3 per cent in 1997 to 2.9 per cent in 2008. The reasons for this are not clear. According to logistic regression analysis of survey responses, the following factors were robustly associated with road accidents involving sleepy driving: driving off the road; good road conditions; longer distance driven since the start of the trip; and fewer years with a driving licence. The following factors are consistently associated with reports of sleep behind the wheel, whether or not it leads to an accident: being male; driving further per year; being younger; and having sleep-related health problems. Taken together these findings suggest that young, inexperienced male drivers who drive long distances may be a suitable target for road safety campaigns aimed at tackling sleepy driving. Copyright © 2012 Elsevier Ltd. All rights reserved.

Commitment of involved actors in the preparation of accidental and post-accident situations: European experiments

International Nuclear Information System (INIS)

Schneider, Th.

2010-01-01

The author briefly describes some approaches developed within the EURANOS European research programme between 2004 and 2009 which aims at promoting the building up of a European network (NERIS) for the management of nuclear accidental and post-accident situations. Notably, he comments the experiment which took place in the Montbeliard district where two types of radiological events have been modelled and simulated: an accident in the Fessenheim nuclear power plant with two scenarios of release, and a transportation accident with a release of radioactive caesium 137. He also evokes the Norwegian experience and some other actions in Finland, Great-Britain, Spain and Slovakia where reflections on the management of accidental and post-accident situations or crisis exercises have been organized

Immediate medical consequences of nuclear accidents: lessons from Chernobyl

International Nuclear Information System (INIS)

Gale, R.P.

1987-01-01

The immediate medical response to the nuclear accident at the Chernobyl nuclear power station involved containment of the radioactivity and evacuation of the nearby population. The next step consisted of assessment of the radiation dose received by individuals, based on biological dosimetry, and treatment of those exposed. Medical care involved treatment of skin burns; measures to support bone marrow failure, gastrointestinal tract injury, and other organ damage (i.e., infection prophylaxis and transfusions) for those with lower radiation dose exposure; and bone marrow transplantation for those exposed to a high dose of radiation. At Chernobyl, two victims died immediately and 29 died of radiation or thermal injuries in the next three months. The remaining victims of the accident are currently well. A nuclear accident anywhere is a nuclear accident everywhere. Prevention and cooperation in response to these accidents are essential goals

Computerized accident management support system: development for severe accident management

International Nuclear Information System (INIS)

Garcia, V.; Saiz, J.; Gomez, C.

1998-01-01

The activities involved in the international Halden Reactor Project (HRP), sponsored by the OECD, include the development of a Computerized Accident Management Support System (CAMS). The system was initially designed for its operation under normal conditions, operational transients and non severe accidents. Its purpose is to detect the plant status, analyzing the future evolution of the sequence (initially using the APROS simulation code) and the possible recovery and mitigation actions in case of an accident occurs. In order to widen the scope of CAMS to severe accident management issues, the integration of the MAAP code in the system has been proposed, as the contribution of the Spanish Electrical Sector to the project (with the coordination of DTN). To include this new capacity in CAMS is necessary to modify the system structure, including two new modules (Diagnosis and Adjustment). These modules are being developed currently for Pressurized Water Reactors and Boiling Water REactors, by the engineering of UNION FENOSA and IBERDROLA companies (respectively). This motion presents the characteristics of the new structure of the CAMS, as well as the general characteristics of the modules, developed by these companies in the framework of the Halden Reactor Project. (Author)

27 CFR 24.230 - Examination of tank car or tank truck.

Science.gov (United States)

2010-04-01

... TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Spirits § 24.230 Examination of tank car or tank truck. Upon arrival of a tank car or tank truck at the bonded wine premises, the proprietor shall... calibration chart is available at the bonded wine premises, the spirits may be gauged by volume in the tank...

Improving user-insurance communication on accident reports

OpenAIRE

Fardoun, Habib Moussa; Alghazzawi, Daniyal M.; Paules Ciprés, Antonio

2014-01-01

This paper presents an easy to use methodology and system for insurance companies targeting at managing traffic accidents reports process. The main objective is to facilitate and accelerate the process of creating and finalizing the necessary accident reports in cases without mortal victims involved. The diverse entities participating in the process from the moment an accident occurs until the related final actions needed are included. Nowadays, this market is limited to the consulting platfo...

Radioactive material (RAM) accident/incident data analysis program

International Nuclear Information System (INIS)

Emerson, E.L.; McClure, J.D.

1985-03-01

This report describes the development of the Radioactive Material Transportation Accident/Incident Data Base (RAM-AIDB), which contains information on the occurrences of transportation accidents and incidents, for radioactive materials (RAM) that are involved in the process of transportation, loading and unloading operation, or temporary storage. These transportation operations are in support of the nuclear fuel cycle for electrical energy generation. This study analyzes in some detail basic accident/incident statistical data, RAM packaging accident response data, and the health effects associated with RAM transport accidents/incidents. This report presents a summary of US RAM transport accident/incident experience for the period 1971 through December 1981. In addition, a sample annual summary of accident/incident experience is presented for the calendar year 1981

[Determining the car driver's position at the moment of the frontal crash with a moving KAMAZ truck].

Science.gov (United States)

Gusarov, A A; Fetisov, V A; Smirenin, S A

2016-01-01

This article is designed to report the results of the comprehensive forensic medical and autotechnical expertise for determining the positions of the driver and the first seat passenger of the GAS-3110 car at the moment of the frontal crash with a KAMAZ-5312 truck. The comparative analysis of the injuries in two subjects one of whom died as a result of the given accident made it possible to conclude that he had occupied the driver's seat in the car. The differential diagnosis was based on the peculiarities of the injuries to the upper extremities with the predominance of the most severe wounds at the right side of the body. Also taken into consideration were the specific conditions of the given frontal collision, design of the GAS-3110 passenger compartment, winter season, night time, and possible neglect of the passive safety means, etc.

Influences on Energy Savings of Heavy Trucks Using Cooperative Adaptive Cruise Control

Energy Technology Data Exchange (ETDEWEB)

Lammert, Michael P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); McAuliffe, Brian [National Research Council Canada; Lu, Xiao-Yun [University of California-Berkeley; Shladover, Steven [University of California-Berkeley; Surcel, Marius-Dorin [FPInnovations; Kailas, Aravind [Volvo Group

2018-04-03

An integrated adaptive cruise control (ACC) and cooperative ACC (CACC) was implemented and tested on three heavy-duty tractor-trailer trucks on a closed test track. The first truck was always in ACC mode, and the followers were in CACC mode using wireless vehicle-vehicle communication to augment their radar sensor data to enable safe and accurate vehicle following at short gaps. The fuel consumption for each truck in the CACC string was measured using the SAE J1321 procedure while travelling at 65 mph and loaded to a gross weight of 65,000 lb, demonstrating the effects of: inter-vehicle gaps (ranging from 3.0 s or 87 m to 0.14 s or 4 m, covering a much wider range than previously reported tests), cut-in and cut-out maneuvers by other vehicles, speed variations, the use of mismatched vehicles (standard trailers mixed with aerodynamic trailers with boat tails and side skirts), and the presence of a passenger vehicle ahead of the platoon. The results showed that energy savings generally increased in a non-linear fashion as the gap was reduced. The middle truck saved the most fuel at gaps shorter than 12 m and the trailing truck saved the most at longer gaps, while lead truck saved the least at all gaps. The cut-in and cut-out maneuvers had only a marginal effect on fuel consumption even when repeated every two miles. The presence of passenger-vehicle traffic had a measurable impact. The fuel-consumption savings on the curves was less than on the straight sections.

Statistical evaluation of design-error related accidents

International Nuclear Information System (INIS)

Ott, K.O.; Marchaterre, J.F.

1980-01-01

In a recently published paper (Campbell and Ott, 1979), a general methodology was proposed for the statistical evaluation of design-error related accidents. The evaluation aims at an estimate of the combined residual frequency of yet unknown types of accidents lurking in a certain technological system. Here, the original methodology is extended, as to apply to a variety of systems that evolves during the development of large-scale technologies. A special categorization of incidents and accidents is introduced to define the events that should be jointly analyzed. The resulting formalism is applied to the development of the nuclear power reactor technology, considering serious accidents that involve in the accident-progression a particular design inadequacy

Light Truck Characteristics, Historical Data Base

Science.gov (United States)

1980-11-01

The report is a description of the data about the physical, operating performance, and market characteristics of light trucks for the model years 1955 through 1977, which is stored on tape in DOT/TSC DEC System 10 computer system. Vehicles are report...

Care of radiation accidents

International Nuclear Information System (INIS)

Renz, K.

1983-01-01

The small probability of a serious radiation accident happening dispenses neither the plants where radiation exposure occurs nor the employers' liability insurance associations from their obligation to make provision for such cases. On the other hand, the efforts involved in such preventive measures must be kept within reasonable limits. As a result of these considerations a concept for taking care of radiation accidents was developed that is based on already existing institutions. The most attention was demanded by questions of organization, logistics, communication and information. The syndrome appearing after acute whole-body irradiation is known. This syndrome in its different stages and the relative therapeutic measures form the basis for the organization of the care of radiation accidents. (orig./MG) [de

Deterministic analyses of severe accident issues

International Nuclear Information System (INIS)

Dua, S.S.; Moody, F.J.; Muralidharan, R.; Claassen, L.B.

2004-01-01

Severe accidents in light water reactors involve complex physical phenomena. In the past there has been a heavy reliance on simple assumptions regarding physical phenomena alongside of probability methods to evaluate risks associated with severe accidents. Recently GE has developed realistic methodologies that permit deterministic evaluations of severe accident progression and of some of the associated phenomena in the case of Boiling Water Reactors (BWRs). These deterministic analyses indicate that with appropriate system modifications, and operator actions, core damage can be prevented in most cases. Furthermore, in cases where core-melt is postulated, containment failure can either be prevented or significantly delayed to allow sufficient time for recovery actions to mitigate severe accidents

Hybrid and electric low-noise cars cause an increase in traffic accidents involving vulnerable road users in urban areas.

Science.gov (United States)

Brand, Stephan; Petri, Maximilian; Haas, Philipp; Krettek, Christian; Haasper, Carl

2013-01-01

Due to resource scarcity, the number of low-noise and electric cars is expected to increase rapidly. The frequent use of these cars will lead to a significant reduction of traffic related noise and pollution. On the other hand, due to the adaption and conditioning of vulnerable road users the number of traffic accidents involving pedestrians and bicyclists is postulated to increase as well. Children, older people with reduced eyesight and the blind are especially reliant on a combination of acoustic and visual warning signals with approaching or accelerating vehicles. This is even more evident in urban areas where the engine sound is the dominating sound up to 30 kph (kilometres per hour). Above this, tyre-road interaction is the main cause of traffic noise. With the missing typical engine sound a new sound design is necessary to prevent traffic accidents in urban areas. Drivers should not be able to switch the sound generator off.

[Occupational accidents in an oil refinery in Brazil].

Science.gov (United States)

Souza, Carlos Augusto Vaz de; Freitas, Carlos Machado de

2002-10-01

Work in oil refineries involves the risk of minor to major accidents. National data show the impact of accidents on this industry. A study was carried out to describe accident profile and evaluate the adequacy of accident reporting system. Data on all accidents reported in an oil refinery in the state of Rio de Janeiro for the year 1997 were organized and analyzed. The study population consisted of 153 injury cases, 83 hired and 69 contracted workers. The variables were: type of accident, operation mode and position of the worker injured. Among hired workers, minor accidents predominated (54.2%) and they occurred during regular operation activities (62.9%). Among contracted workers, there also predominated minor accidents (75.5%) in a higher percentage, but they occurred mainly during maintenance activities (96.8%). The study results showed that there is a predominance of accidents in lower hierarchy workers, and these accidents occur mainly during maintenance activities. There is a need to improve the company's accident reporting system and accident investigation procedures.

Nuclear Liability and Insurance Protection for Nuclear Transport Accidents Involving Non-Contracting EU States: An assessment

International Nuclear Information System (INIS)

Horbach, N. L. J. T.

2006-01-01

This paper provides an analysis of the possible complications and consequences with respect to nuclear liability and insurance protection applicable in respect of transport activities resulting in damage suffered and/or accidents occurring in EU States that are not party to the Paris Convention. It looks at the different legal aspects (jurisdiction, applicable law, liability amounts, reciprocity) should the revised Vienna and Paris Convention become applicable in comparison with the unrevised Conventions. Within Europe, a large number of States are party to the 1960 Paris Convention and the 1963 Brussels Supplementary Convention, providing liability and insurance protection, in general, up to a limit of 300 million SDRs (or even higher). In principle, such protection is confined to nuclear incidents occurring and nuclear damage suffered in the territory of Contracting Parties, including, as recommended, the high seas, unless the legislation of the Installation State determines otherwise (Article 2). The geographical scope of application of the Paris Convention would thus vary according to the law of the Installation State. However, some EU States never became party to the Paris Convention, and are not bound by its the liability principles (notably, channelling of liability), such as Austria, Luxembourg and Ireland. Transport accidents involving these countries might therefore result in liability claims outside the treaty liability regime against operators, suppliers, carriers or persons involved and for types of damages different from those currently covered by the Paris Convention (e.g., environmental damage). It is uncertain to what extent liability insurance of the installation operators would provide adequate protection and whether related damage claims can be enforceable. In addition, a number of newly entered EU States are party to the Vienna Convention, which, although bound by liability principles basically similar to those of the Paris Convention, will

Experience with first aid in radiation sources accidents

International Nuclear Information System (INIS)

Klener, V.

1979-01-01

More than 20 years of experience at the Radiation Hygiene Centre of the Prague Institute of Hygiene and Epidemiology with prevention of accidents involving sources of radiation and the Centre's participation in providing medical aid in such accidents are described. A list is given of major types of accidents over the past decade. Prevalent were accidents involving sealed gamma sources, resulting in excessive local irradiation with serious skin damage or injury to some of the deeper structures of the hands, requiring plastic operation. Chromosomal picture investigation allows the estimation of the equivalent body dose which only reached higher values in a single case recorded (1.5 Gy = 150 rad). Organisational measures are described for emergencies and the task is shown by radiation hygiene departments attached to regional hygiene stations. The present system is capable of providing adequate, prompt and effective assistance. (author)

Idling Reduction for Long-Haul Trucks: An Economic Comparison of On-Board and Wayside Technologies

Energy Technology Data Exchange (ETDEWEB)

Gaines, Linda [Argonne National Lab. (ANL), Argonne, IL (United States); Weikersheimer, Patricia [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-09-01

Reducing the idling of long-haul heavy-duty trucks has long been recognized as a particularly low-hanging fruit of fuel efficiency and emissions reduction. The displacement of about 10 hours of diesel idling every day, for most days of the year, for as many as a million long-haul trucks has very clear benefits. This report considers the costs and return on investment (ROI) for idling reduction (IR) equipment for both truck owners and electrified parking space (EPS) equipment owners. For the truck owners, the key variables examined are idling hours to be displaced (generally 1,000 to 2,000 hours per year) and the price of fuel ($0 to $5/gal). The ideal IR option would provide complete services in varied climates in any location and offer the best ROI on trucks that log many idling hours. For trucks that have fewer idling hours, options with a fixed cost per hour (i.e., EPS) might be most attractive if they were available to all, or even most, truck drivers. EPS, however, is particularly cost effective for trucks on prescribed routes with a need for regular, extended stops at terminals. (EPS is also called truck stop electrification, or TSE.) The analysis shows that all IR options save money when fuel costs more than $2/gal. For trucks requiring bunk heat, a simple heater (plug-in or diesel) is almost always the most costeffective way to provide heat, even if the truck is equipped with an auxiliary power unit (APU) or is parked at a single-system EPS location. For trucks requiring bunk air-conditioning, the use of single-system EPS is most cost effective for those logging fewer idling hours. Even for trucks with higher idling hours, the cost of EPS may be about the same as that for on-board air-conditioning. Clearly, trucks’ locations and seasonal factors—and the availability of EPS— are significant in the choice of “best fit” IR equipment for truck owners. This report also considers costs and payback for owners of EPS infrastructure. An industry that 5

Study on heavy duty truck stability control by braking force control; Seidoryoku seigyo ni yoru truck no sharyo kyodo anteika ni taisuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Matsuda, K; Shinjo, H; Harada, M; Ohata, K; Sakata, K [Mitsubishi Motors Corp., Tokyo (Japan)

1997-10-01

Now a days we are discussing about the vehicle stability control system which freely controls the braking force of each wheel to apply the yaw t and decelerate the vehicle. The system drastically improve the vehicle cornering performance and stabilize the vehicle behavior in its critical area. This paper discusses a point to notice in case of applying this technique for heavy duty trucks, and describes the possibility of the stabilization for vehicle cornering behavior about heavy duty truck. 3 refs., 10 figs., 2 tabs.

Air-cushion vehicles as an alternative to conventional industrial trucks

International Nuclear Information System (INIS)

Marr, E.

2003-01-01

Protective shieldings must be used for the transportation of radioactive materials, such as drums and containers within the control area, in order to observe the activity classes of the rooms. As a result of the change in the radiation protection ordinance, the operating areas of the floor conveyors have to be protected even more, i.e. transportation weights are becoming even bigger. When using pallet lift trucks without drive, weights over 2 tons are virtually unable to be operated. A fork-lift truck must be used for higher loads. If the transportation weight (transportation load and net weight of the lift truck) is doubled, usage within buildings is very restricted through the ceiling net load. This is the range of application of air cushion vehicles, in particular if positioning accuracy and remote-controlled driving become necessary. (orig.)

Accidents cutting and piercing in a School of Dentistry

Directory of Open Access Journals (Sweden)

Maria Cristina Zindel Deboni

2010-04-01

Full Text Available Objective: To assess the occurrence and characteristics of the reported accidents with perforating-cutting materials involving students, staff and faculty members, between 2000 and 2005 at the Dental Clinic of the School of Dentistry of the University of São Paulo. Methods: A survey of the records of reported occurrences of accidents was made, considering the material that caused the accident, time of day of the occurrence, the discipline in which it occurred, and clinical conduct adopted in the emergency room. When available, the results of the laboratory exams of the accident victim and the source patient were also taken into consideration. Results: The data assessed showed there were 40 accident reports, of which 39 reports involved undergraduate students and 1 staff member. The instrument that caused most accidents was the anesthetic needle and largest number of these accidents occurred in the Surgery discipline. However, 50% of the records did not present complete information, which prevented a more accurate epidemiological assessment. Conclusion: The data obtained led to the conclusion that the rate of accidents is extremely low considering the number of clinical attendances provided in the period and raises the hypothesis that many cases were not reported.

MDCT findings in sports and recreational accidents.

Science.gov (United States)

Bensch, Frank V; Koivikko, Mika P; Koskinen, Seppo K

2011-12-01

Sports and recreational accidents involving critical areas of the body occur commonly in the general population. Reports on their demographics and recommendations for screening procedures are, however, few. To assess injuries of the craniofacial area, spine, and torso resulting from sports and recreational accidents with multidetector computed tomography (MDCT) as primary imaging method in a Level I trauma center. All emergency room CT requests over a time span of 105 months were reviewed retrospectively for trauma mechanism and injury. Patients were identified using an electronic picture archiving and communications system (PACS), and MDCT studies interpreted by two radiologists independently. Of a total of 5898 patients, 492 patients (301 boys/men, 191 girls/women, age range 2-76 years, mean 33.5 years, median 29.5 years) with sports or recreational accidents emerged. A total of 102 traumatic findings were diagnosed, thereof 72 (71%) serious. The three most commonly encountered serious injuries were intracranial injury, fractures of facial bones, and vertebral injuries. The three most common injury mechanisms were bicycling, horseback riding, and team ball sports. Patients from recreational activities were on average significantly younger (29.2 years) than those from sports accidents (36.9 years; P accidents presented with an overall incidence of 21%, of which 71% are serious. The most common mechanisms of injury were bicycling, horseback riding, and team ball sports. The largest incidence of serious injury involved bicycling. Because of the high probability of a serious injury and the high energies that are often involved in these accidents, we recommend ruling out of internal injury by MDCT as the primary imaging modality.

Chemical phenomena under severe accident conditions

International Nuclear Information System (INIS)

Powers, D.A.

1988-01-01

A severe nuclear reactor accident is expected to involve a vast number of chemical processes. The chemical processes of major safety significance begin with the production of hydrogen during steam oxidation of fuel cladding. Physico-chemical changes in the fuel and the vaporization of radionuclides during reactor accidents have captured much of the attention of the safety community in recent years. Protracted chemical interactions of core debris with structural concrete mark the conclusion of dynamic events in a severe accident. An overview of the current understanding of chemical processes in severe reactor accident is provided in this paper. It is shown that most of this understanding has come from application of findings from other fields though a few areas have in the past been subject to in-depth study of a fundamental nature. Challenges in the study of severe accident chemistry are delineated

Accidents - Chernobyl accident

International Nuclear Information System (INIS)

2004-01-01

This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

Truck drivers’ perceptions on wearable devices and health promotion: a qualitative study

Directory of Open Access Journals (Sweden)

Rama Greenfield

2016-07-01

Full Text Available Abstract Background Professional truck drivers, as other shift workers, have been identified as a high-risk group for various health conditions including cardiovascular disease, obesity, diabetes, sleep apnoea and stress. Mobile health technologies can potentially improve the health and wellbeing of people with a sedentary lifestyle such as truck drivers. Yet, only a few studies on health promotion interventions related to mobile health technologies for truck drivers have been conducted. We aimed to explore professional truck drivers’ views on health promotion delivered via mobile health technologies such as wearable devices. Methods We conducted a phenomenological qualitative study, consisting of four semi-structured focus groups with 34 full-time professional truck drivers in the UK. The focus groups were audio-taped, transcribed verbatim and analysed using thematic content analysis. We discussed drivers’ perceptions of their health, lifestyle and work environment, and their past experience and expectations from mobile health technologies. Results The participants viewed their lifestyle as unhealthy and were aware of possible consequences. They expressed the need and wish to change their lifestyle, yet perceived it as an inherent, unavoidable outcome of their occupation. Current health improvement initiatives were not always aligned with their working conditions. The participants were generally willing to use mobile health technologies such as wearable devices, as a preventive measure to avoid prospect morbidity, particularly cardiovascular diseases. They were ambivalent about privacy and the risk of their employer’s monitoring their clinical data. Conclusions Wearable devices may offer new possibilities for improving the health and wellbeing of truck drivers. Drivers were aware of their unhealthy lifestyle. They were interested in changing their lifestyle and health. Drivers raised concerns regarding being continuously monitored by

Modeling mechanical restriction differences between car and heavy truck in two-lane cellular automata traffic flow model

Science.gov (United States)

Li, Xin; Li, Xingang; Xiao, Yao; Jia, Bin

2016-06-01

Real traffic is heterogeneous with car and truck. Due to mechanical restrictions, the car and the truck have different limited deceleration capabilities, which are important factors in safety driving. This paper extends the single lane safety driving (SD) model with limited deceleration capability to two-lane SD model, in which car-truck heterogeneous traffic is considered. A car has a larger limited deceleration capability while a heavy truck has a smaller limited deceleration capability as a result of loaded goods. Then the safety driving conditions are different as the types of the following and the leading vehicles vary. In order to eliminate the well-known plug in heterogeneous two-lane traffic, it is assumed that heavy truck has active deceleration behavior when the heavy truck perceives the forming plug. The lane-changing decisions are also determined by the safety driving conditions. The fundamental diagram, spatiotemporal diagram, and lane-changing frequency were investigated to show the effect of mechanical restriction on heterogeneous traffic flow. It was shown that there would be still three traffic phases in heterogeneous traffic condition; the active deceleration of the heavy truck could well eliminate the plug; the lane-changing frequency was low in synchronized flow; the flow and velocity would decrease as the proportion of heavy truck grows or the limited deceleration capability of heavy truck drops; and the flow could be improved with lane control measures.

LASER WELDING WITH MICRO-JET COOLING FOR TRUCK FRAME WELDING

Directory of Open Access Journals (Sweden)

Jan PIWNIK

2017-12-01

Full Text Available The aim of this paper is to analyse the mechanical properties of the weld steel structure of car body truck frames after laser welding. The best welding conditions involve the use of proper materials and alloy elements in steel and filer materials, in addition to welding technology, state of stress and temperature of exploitation. We present for the first time the properties of steel track structures after laser welding with micro-jet cooling. Therefore, good selection of both welding parameters and micro-jet cooling parameters is very important to achieve a proper steel structure. In this study, the metallographic structure, tensile results and impact toughness of welded joints have been analysed in terms of welding parameters.

Structural evaluation for the core sampling trucks, RMCS operations, 200 Area

International Nuclear Information System (INIS)

Islam, M.A.

1996-01-01

This report evaluates the structural adequacy and the integrity of the existing core sampling trucks to withstand impact should the trucks drop off the ramp, either onto the soft ground or onto a non-yielding surface due to operational error, wind, or earthquake. The report also addresses if the allowable tank dome load will be exceeded by the addition of the impact load

A Study on the Operation Strategy for Combined Accident including TLOFW accident

International Nuclear Information System (INIS)

Kim, Bo Gyung; Kang, Gook Young; Yoon, Ho Joon

2014-01-01

It is difficult for operators to recognize the necessity of a feed-and-bleed (F-B) operation when the loss of coolant accident and failure of secondary side occur. An F-B operation directly cools down the reactor coolant system (RCS) using the primary cooling system when residual heat removal by the secondary cooling system is not available. The plant is not always necessary the F-B operation when the secondary side is failed. It is not necessary to initiate an F-B operation in the case of a medium or large break because these cases correspond to low RCS pressure sequences when the secondary side is failed. If the break size is too small to sufficiently decrease the RCS pressure, the F-B operation is necessary. Therefore, in the case of a combined accident including a secondary cooling system failure, the provision of clear information will play a critical role in the operators' decision to initiate an F-B operation. This study focuses on the how we establish the operation strategy for combined accident including the failure of secondary side in consideration of plant and operating conditions. Previous studies have usually focused on accidents involving a TLOFW accident. The plant conditions to make the operators confused seriously are usually the combined accident because the ORP only focuses on a single accident and FRP is less familiar with operators. The relationship between CET and PCT under various plant conditions is important to decide the limitation of initiating the F-B operation to prevent core damage

Prospects of development of land driverless trucks

Science.gov (United States)

Bakhmutov, S.; Saykin, A.; Endachev, D.; Evgrafov, V.; Shagurin, A.; Kulikov, I.; Fedoseev, K.

2018-02-01

The paper is dedicated to the problem of creation and efficient use of driverless trucks. It also contains general analysis of foreign experience and development trends. The concept of FSUE “NAMI” for development of a platoon of driverless trucks for cargo transportation between specialized terminals on public roads is provided. A road train with virtual couplings where the lead vehicle has a driver and the rest are driverless is proposed as a base for the driverless platoon. The platoon is formed by such road trains, which ensures extended functional features, including the possibility to form platoons of road trains from different logistics centers and with different destinations, quick reforming of the platoon in the logistics centers, possibility to split the platoon when driving on public roads, higher precision of control over the platoon during driving, etc. It is also shown that in order to improve the efficiency of cargo transportation, driverless cargo platforms (trucks) shall be designed without a cabin. The paper also considers the ways to reduce the price of driverless trucks by creating a special road infrastructure, which will allow transfer of the most expensive subsystems of driverless vehicles to such infrastructure. Upon that, the following subsystems will remain within the driverless chassis: navigation, communication, chassis control and ADAS. It is noted that creation of such infrastructure will require high investments, therefore, gradual implementation of such systems is seen as rational. It is shown that the most appropriate area for these purposes is transregional cargo transportation. It is noted that the economic reasons for implementation of the proposed concept are as follows: significant reduction of the number of drivers; significant simplification of the driverless platform control system and reduction of the price of subsystems; no need for the driver’s cabin within the driverless platform; fuel economy when driving within a

Accidents in The Netherlands involving heavy motor vehicles : an analysis concerning underrun protection of rear ends, compared to the sides and the front ends. On behalf of RDW Vehicle Technology & Information Centre.

NARCIS (Netherlands)

Kampen, L.T.B. van

1998-01-01

In this report accident data concerning heavy vehicles (all motor vehicles with a total weight of more than 3500 kg) are studied. Special attention is given to the question whether accidents involving heavy motor vehicles gave specific reason for concern regarding other road users with respect to

Ticketing aggressive cars and trucks (TACT): How does it work on city streets?

Science.gov (United States)

Telford, Russell; Cook, Lawrence J; Olson, Lenora M

2018-02-17

The purpose of this study was to determine the feasibility of modifying the Ticking Aggressive Cars and Trucks (TACT) program, originally designed to work on state highways, within a metropolitan area to reduce unsafe interactions and their related crashes between drivers of large trucks and passenger vehicles. Using crash data, the driving behaviors most commonly associated with large truck and passenger vehicle crashes were identified. A public awareness campaign using media messaging and increased law enforcement was created targeting these associated behaviors. The frequency of these behaviors both before and after the public awareness campaign was determined through observation of traffic at 3 specific locations within the city. Each location had a sufficient volume of large truck and passenger traffic to observe frequent interactions. Pre- and postintervention data were compared using negative binomial regression with generalized estimating equations to evaluate whether the campaign was associated with a reduction in the identified driving behaviors. A comparison between crash data from before, during, and after the campaign and crashes during the same time periods in previous years did not show a significant difference (P =.081). The number of large trucks observed in traffic remained the same during pre- and postintervention periods (P =.625). The rates of negative interactions per 100 large trucks decreased for both large trucks and passenger vehicles after the intervention, with calculated rate ratios of 0.58 (95% confidence interval [CI], 0.48, 0.70) and 0.31 (95% CI, 0.20, 0.47). The greatest reduction was seen in passenger vehicles following too close, with a rate ratio of 0.21 (95% CI, 0.15, 0.30). Although designed for reducing crashes on highways, the TACT program can be an effective approach for improving driver behaviors on city streets.

Safety and Health Standard 110: Incident/accident reporting and investigation

Energy Technology Data Exchange (ETDEWEB)

Sones, K. [West Kootenay Power, BC (Canada)

1999-10-01

Incident/accident reporting requirements in effect at West Kootenay Power are discussed. Details provided include definitions of low risk, high risk, and critical events, the incidents to be reported, the nature of the reports, the timelines, the investigation to be undertaken for each type of incident/accident, counselling services available to employees involved in serious incidents, and the procedures to be followed in accidents involving serious injury to non-employees. The emphasis is on the `critical five` high risk events and the procedures relating to them.

Factors Affecting Road Traffic Accident in Batu Pahat, Johor, Malaysia

Science.gov (United States)

Che-Him, Norziha; Roslan, Rozaini; Saifullah Rusiman, Mohd; Khalid, Kamil; Ghazali Kamardan, M.; Azbi Arobi, Farquis; Mohamad, Nazeera

2018-04-01

A road traffic accident resulted from the combination of factors related to the few components of the system involving environment, roads, road users, vehicles and the interaction between those systems. Road traffic accident (RTA) in Malaysia recorded as the highest fatality rate (per 100,000 population) among the ASEAN countries. In 2016, more than half of million cases accident recorded with more than 7,000 people were killed. Therefore, the RTA is one of the most critical issue in Malaysia even become the worldwide burden to authority. Generally, driving is a complex process which involves movement of a vehicle by either a computer or human controller. However, failure to control and coordinate will contribute to an accident. The objective of this study is to identify the pattern of accident in Johor Malaysia and to examine the relationship between the number of accident and the types of vehicles and roads. The results could help the government to recognise the different patterns, types of vehicles and roads that show major factors in the increasing of road traffic accident in Malaysia.

Scheduling trucks in cross docking systems with temporary storage and dock repeat truck holding pattern using genetic algorithm

Directory of Open Access Journals (Sweden)

Ehsan Ghobadian

2013-02-01

Full Text Available Cross docking is one of the most important issues in management of supply chains. In cross docking, different items delivered to a warehouse by inbound trucks are directly arranged and reorganized based on customer demands, routed and loaded into outbound trucks for delivery purposes to customers without virtually keeping them at the warehouse. If any item is kept in storage, it is normally for a short amount of time, say less than 24 hours. In this paper, we consider a special case of cross docking where there is temporary storage and implements genetic algorithm to solve the resulted problem for some realistic test problems. In our method, we first use some heuristics as initial solutions and then improve the final solution using genetic algorithm. The performance of the proposed model is compared with alternative solution strategy, the GRASP method.

JAERI's activities in JCO accident

International Nuclear Information System (INIS)

2000-09-01

The Japan Atomic Energy Research Institute (JAERI) was actively involved in a variety of technical supports and cooperative activities, such as advice on terminating the criticality condition, contamination checks of the residents and consultation services for the residents, as emergency response actions to the criticality accident at the uranium processing facility operated by the JCO Co. Ltd., which occurred on September 30, 1999. These activities were carried out in collaborative ways by the JAERI staff from the Tokai Research Establishment, Naka Fusion Research Establishment, Oarai Research Establishment, and Headquarter Office in Tokyo. As well, the JAERI was engaged in the post-accident activities such as identification of accident causes, analyses of the criticality accident, and dose assessment of exposed residents, to support the Headquarter for Accident Countermeasures of the Science and Technology Agency (STA), the Accident Investigation Committee and the Health Control Committee of the Nuclear Safety Commission of Japan (NSC). This report compiles the activities, that the JAERI has conducted to date, including the discussions on measures for terminating the criticality condition, evaluation of the fission number, radiation monitoring in the environment, dose assessment, analyses of criticality dynamics. (author)

The effect of the descent technique and truck cabin layout on the landing impact forces.

Science.gov (United States)

Patenaude, S; Marchand, D; Samperi, S; Bélanger, M

2001-12-01

The majority of injuries to truckers are caused by falls during the descent from the cab of the truck. Several studies have shown that the techniques used to descend from the truck and the layout of the truck's cabin are the principal cause of injury. The goal of the present study was to measure the effects of the descent techniques used by the trucker and the layout of the truck's cabin on the impact forces absorbed by the lower limbs and the back. Kinematic data, obtained with the aid of a video camera, were combined with the force platform data to allow for calculation of the lower limb and L5-S1 torques as well as L5-S1 compressive forces. The trucker descended from two different conventional tractor cabin layouts. Each trucker descended from cabin using either "facing the truck" (FT) or "back to the truck" (BT) techniques. The results demonstrate that the BT technique produces greater ground impact forces than the FT technique, particularly when the truck does not have a handrail. The BT technique also causes an increase in the compressive forces exerted on the back. In conclusion, the use of the FT technique along with the aids (i.e., handrails and all the steps) help lower the landing impact forces as well as the lumbosacral compressive forces.

Tolerance to physical load in victims of Chernobyl accident with hypertension disease (the data 15 year after the accident)

International Nuclear Information System (INIS)

Khomazyuk, Yi.M.; Koval'ov, O.S.; Sidorenko, G.V.

2003-01-01

The study involved 210 participants of Chernobyl accident clean-up. Fifteen years after the accident, threshold power (Wt) and total volume of the work (TVW) reached the proper values for the given age and body mass in 70% of cases. More significant limitation of TPL was observed in stage II hypertension

Modelling and control of a light-duty hybrid electric truck

OpenAIRE

Park, Jong-Kyu