Insights from Severe Accident Analyses for Verification of VVER SAMG

Energy Technology Data Exchange (ETDEWEB)

Gaikwad, A. J.; Rao, R. S.; Gupta, A.; Obaidurrahaman, K., E-mail: avinashg@aerb.gov.in [Nuclear Safety Analysis Division, Atomic Energy Regulatory Board, Mumbai (India)

2014-10-15

The severe accident analyses of simultaneous rupture of all four steam lines (case-a), simultaneous occurrence of LOCA with SBO (case-b) and Station blackout (case-c) were performed with the computer code ASTEC V2r2 for a typical VVER-1000. The results obtained will be used for verification of sever accident provisions and Severe Accident Management Guidelines (SAMG). Auxiliary feed water and emergency core cooling systems are modelled as boundary conditions. The ICARE module is used to simulate the reactor core, which is divided into five radial regions by grouping similarly powered fuel assemblies together. Initially, CESAR module computes thermal hydraulics in primary and secondary circuits. As soon as core uncovery begins, the ICARE module is actuated based on certain parameters, and after this, ICARE module computes the thermal hydraulics in the core, bypass, downcomer and the lower plenum. CESAR handles the remaining components in the primary and secondary loops. CPA module is used to simulate the containment and to predict the thermal-hydraulic and hydrogen behaviour in the containment. The accident sequences were selected in such a way that they cover low/high pressure and slow/fast core damage progression events. Events simulated included slow progression events with high pressure and fast accident progression with low primary pressure. Analysis was also carried out for the case of SBO with the opening of the PORVs when core exit temperature exceeds certain value as part of SAMG. Time step sensitivity study was carried out for LOCA with SBO. In general the trends and magnitude of the parameters are as expected. The key results of the above analyses are presented in this paper. (author)

Severe accident recriticality analyses (SARA)

DEFF Research Database (Denmark)

Frid, W.; Højerup, C.F.; Lindholm, I.

2001-01-01

with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality-both super-prompt power bursts and quasi steady-state power......Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies......, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g(-1), was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s(-1). In most cases, however, the predicted energy deposition was smaller, below...

Source terms derived from analyses of hypothetical accidents, 1950-1986

International Nuclear Information System (INIS)

Stratton, W.R.

1987-01-01

This paper reviews the history of reactor accident source term assumptions. After the Three Mile Island accident, a number of theoretical and experimental studies re-examined possible accident sequences and source terms. Some of these results are summarized in this paper

Deterministic analyses of severe accident issues

International Nuclear Information System (INIS)

Dua, S.S.; Moody, F.J.; Muralidharan, R.; Claassen, L.B.

2004-01-01

Severe accidents in light water reactors involve complex physical phenomena. In the past there has been a heavy reliance on simple assumptions regarding physical phenomena alongside of probability methods to evaluate risks associated with severe accidents. Recently GE has developed realistic methodologies that permit deterministic evaluations of severe accident progression and of some of the associated phenomena in the case of Boiling Water Reactors (BWRs). These deterministic analyses indicate that with appropriate system modifications, and operator actions, core damage can be prevented in most cases. Furthermore, in cases where core-melt is postulated, containment failure can either be prevented or significantly delayed to allow sufficient time for recovery actions to mitigate severe accidents

Categorization of PWR accident sequences and guidelines for fault trees: seismic initiators

International Nuclear Information System (INIS)

Kimura, C.Y.

1984-09-01

This study developed a set of dominant accident sequences that could be applied generically to domestic commercial PWRs as a standardized basis for a probabilistic seismic risk assessment. This was accomplished by ranking the Zion 1 accident sequences. The pertinent PWR safety systems were compared on a plant-by-plant basis to determine the applicability of the dominant accident sequences of Zion 1 to other PWR plants. The functional event trees were developed to describe the system functions that must work or not work in order for a certain accident sequence to happen, one for pipe breaks and one for transients

TITAN: a computer program for accident occurrence frequency analyses by component Monte Carlo simulation

Energy Technology Data Exchange (ETDEWEB)

Nomura, Yasushi [Department of Fuel Cycle Safety Research, Nuclear Safety Research Center, Tokai Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Tamaki, Hitoshi [Department of Safety Research Technical Support, Tokai Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Kanai, Shigeru [Fuji Research Institute Corporation, Tokyo (Japan)

2000-04-01

In a plant system consisting of complex equipments and components for a reprocessing facility, there might be grace time between an initiating event and a resultant serious accident, allowing operating personnel to take remedial actions, thus, terminating the ongoing accident sequence. A component Monte Carlo simulation computer program TITAN has been developed to analyze such a complex reliability model including the grace time without any difficulty to obtain an accident occurrence frequency. Firstly, basic methods for the component Monte Carlo simulation is introduced to obtain an accident occurrence frequency, and then, the basic performance such as precision, convergence, and parallelization of calculation, is shown through calculation of a prototype accident sequence model. As an example to illustrate applicability to a real scale plant model, a red oil explosion in a German reprocessing plant model is simulated to show that TITAN can give an accident occurrence frequency with relatively good accuracy. Moreover, results of uncertainty analyses by TITAN are rendered to show another performance, and a proposal is made for introducing of a new input-data format to adapt the component Monte Carlo simulation. The present paper describes the calculational method, performance, applicability to a real scale, and new proposal for the TITAN code. In the Appendixes, a conventional analytical method is shown to avoid complex and laborious calculation to obtain a strict solution of accident occurrence frequency, compared with Monte Carlo method. The user's manual and the list/structure of program are also contained in the Appendixes to facilitate TITAN computer program usage. (author)

TITAN: a computer program for accident occurrence frequency analyses by component Monte Carlo simulation

International Nuclear Information System (INIS)

Nomura, Yasushi; Tamaki, Hitoshi; Kanai, Shigeru

2000-04-01

In a plant system consisting of complex equipments and components for a reprocessing facility, there might be grace time between an initiating event and a resultant serious accident, allowing operating personnel to take remedial actions, thus, terminating the ongoing accident sequence. A component Monte Carlo simulation computer program TITAN has been developed to analyze such a complex reliability model including the grace time without any difficulty to obtain an accident occurrence frequency. Firstly, basic methods for the component Monte Carlo simulation is introduced to obtain an accident occurrence frequency, and then, the basic performance such as precision, convergence, and parallelization of calculation, is shown through calculation of a prototype accident sequence model. As an example to illustrate applicability to a real scale plant model, a red oil explosion in a German reprocessing plant model is simulated to show that TITAN can give an accident occurrence frequency with relatively good accuracy. Moreover, results of uncertainty analyses by TITAN are rendered to show another performance, and a proposal is made for introducing of a new input-data format to adapt the component Monte Carlo simulation. The present paper describes the calculational method, performance, applicability to a real scale, and new proposal for the TITAN code. In the Appendixes, a conventional analytical method is shown to avoid complex and laborious calculation to obtain a strict solution of accident occurrence frequency, compared with Monte Carlo method. The user's manual and the list/structure of program are also contained in the Appendixes to facilitate TITAN computer program usage. (author)

A methodology for analyzing precursors to earthquake-initiated and fire-initiated accident sequences

International Nuclear Information System (INIS)

Budnitz, R.J.; Lambert, H.E.; Apostolakis, G.

1998-04-01

This report covers work to develop a methodology for analyzing precursors to both earthquake-initiated and fire-initiated accidents at commercial nuclear power plants. Currently, the U.S. Nuclear Regulatory Commission sponsors a large ongoing project, the Accident Sequence Precursor project, to analyze the safety significance of other types of accident precursors, such as those arising from internally-initiated transients and pipe breaks, but earthquakes and fires are not within the current scope. The results of this project are that: (1) an overall step-by-step methodology has been developed for precursors to both fire-initiated and seismic-initiated potential accidents; (2) some stylized case-study examples are provided to demonstrate how the fully-developed methodology works in practice, and (3) a generic seismic-fragility date base for equipment is provided for use in seismic-precursors analyses. 44 refs., 23 figs., 16 tabs

Accident sequence analysis of human-computer interface design

International Nuclear Information System (INIS)

Fan, C.-F.; Chen, W.-H.

2000-01-01

It is important to predict potential accident sequences of human-computer interaction in a safety-critical computing system so that vulnerable points can be disclosed and removed. We address this issue by proposing a Multi-Context human-computer interaction Model along with its analysis techniques, an Augmented Fault Tree Analysis, and a Concurrent Event Tree Analysis. The proposed augmented fault tree can identify the potential weak points in software design that may induce unintended software functions or erroneous human procedures. The concurrent event tree can enumerate possible accident sequences due to these weak points

Accident analyses in nuclear power plants following external initiating events and in the shutdown state. Final report; Unfallanalysen in Kernkraftwerken nach anlagenexternen ausloesenden Ereignissen und im Nichtleistungsbetrieb. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Loeffler, Horst; Kowalik, Michael; Mildenberger, Oliver; Hage, Michael

2016-06-15

The work which is documented here provides the methodological basis for improvement of the state of knowledge for accident sequences after plant external initiating events and for accident sequences which begin in the shutdown state. The analyses have been done for a PWR and for a BWR reference plant. The work has been supported by the German federal ministry BMUB under the label 3612R01361. Top objectives of the work are: - Identify relevant event sequences in order to define characteristic initial and boundary conditions - Perform accident analysis of selected sequences - Evaluate the relevance of accident sequences in a qualitative way The accident analysis is performed with the code MELCOR 1.8.6. The applied input data set has been significantly improved compared to previous analyses. The event tree method which is established in PSA level 2 has been applied for creating a structure for a unified summarization and evaluation of the results from the accident analyses. The computer code EVNTRE has been applied for this purpose. In contrast to a PSA level 2, the branching probabilities of the event tree have not been determined with the usual accuracy, but they are given in an approximate way only. For the PWR, the analyses show a considerable protective effect of the containment also in the case of beyond design events. For the BWR, there is a rather high probability for containment failure under core melt impact, but nevertheless the release of radionuclides into the environment is very limited because of plant internal retention mechanisms. This report concludes with remarks about existing knowledge gaps and with regard to core melt sequences, and about possible improvements of the plant safety.

Probabilistic approach in treatment of deterministic analyses results of severe accidents

International Nuclear Information System (INIS)

Krajnc, B.; Mavko, B.

1996-01-01

Severe accidents sequences resulting in loss of the core geometric integrity have been found to have small probability of the occurrence. Because of their potential consequences to public health and safety, an evaluation of the core degradation progression and the resulting effects on the containment is necessary to determine the probability of a significant release of radioactive materials. This requires assessment of many interrelated phenomena including: steel and zircaloy oxidation, steam spikes, in-vessel debris cooling, potential vessel failure mechanisms, release of core material to the containment, containment pressurization from steam generation, or generation of non-condensable gases or hydrogen burn, and ultimately coolability of degraded core material. To asses the answer from the containment event trees in the sense of weather certain phenomenological event would happen or not the plant specific deterministic analyses should be performed. Due to the fact that there is a large uncertainty in the prediction of severe accidents phenomena in Level 2 analyses (containment event trees) the combination of probabilistic and deterministic approach should be used. In fact the result of the deterministic analyses of severe accidents are treated in probabilistic manner due to large uncertainty of results as a consequence of a lack of detailed knowledge. This paper discusses approach used in many IPEs, and which assures that the assigned probability for certain question in the event tree represent the probability that the event will or will not happen and that this probability also includes its uncertainty, which is mainly result of lack of knowledge. (author)

A study on hydrogen deflagration for selected severe accident sequences in Ringhals 3

Energy Technology Data Exchange (ETDEWEB)

Gustavsson, V.; Moeller, E. [SwedPower AB (Sweden)

2002-01-01

In this report, we have investigated the most important severe accident sequences in Ringhals 3, a Westinghouse 3-loop PWR, concerning hydrogen generation and containment pressure at hydrogen deflagration. In order to analyze the accident sequences and to calculate the hydrogen production, the computer code MAAP (Modular Accident Analysis Program) was used. Six accident sequences were studied, where four were LOCA cases and two transients. MAAP gives the evolution of the accident and particularly the pressure in the containment and the production of hydrogen as a function of time. The pressure peaks at deflagration were calculated by the method AICC-Adiabatic Isochoric Complete Combustion. The results from these calculations are conservative for two reasons. Adiabatic combustion means that the heat losses to structures in the containment are neglected. The combustion is also assumed to occur once and all available hydrogen is burned. The maximum pressure in five analysed cases was compared with the failure pressure of the containment. In the LOCA case, 373 kg hydrogen was burned and the resulting peak pressure in the containment was 0,53 MPa. In the transient, where 720 kg hydrogen was burned, the peak pressure was 0,69 MPa. This is the same as the failure pressure of the containment. Finally, in the conservative case, 980 kg hydrogen was burned and the resulting peak pressure 0,96 MPa. However, it should be noted that these conclusions are conservative from two points of view. Firstly a more realistic (than AICC) calculation of the peak pressure would give a lower value than 0,69 MPa. Secondly, there is conservatism in the evaluation of the failure pressure. (au)

Probabilistic studies of accident sequences

International Nuclear Information System (INIS)

Villemeur, A.; Berger, J.P.

1986-01-01

For several years, Electricite de France has carried out probabilistic assessment of accident sequences for nuclear power plants. In the framework of this program many methods were developed. As the interest in these studies was increasing and as adapted methods were developed, Electricite de France has undertaken a probabilistic safety assessment of a nuclear power plant [fr

Some Examples of Accident Analyses for RB Reactor

International Nuclear Information System (INIS)

Pesic, M.

2002-01-01

The RB reactor is heavy water critical assembly operated in the Vinca Institute of Nuclear Sciences, Belgrade, Yugoslavia, since April 1959. The first Safety Analysis Report of the RB critical assembly was prepared in 1961/62. But, the first accidental analysis was done in late 1958 in aim the examine power transient and total equivalent doses received by the staff during the reactivity accident occurred on October 15, 1958. Since 1960, the RB reactor is modified few times. Beside initial natural uranium metal fuel rods, new fuel (TVR-S types) from 2% enriched metal uranium and 80% enriched UO 2 were available since 1962 and 1976, respectively. Also, modifications in control and safety systems of the reactor were done occasionally. Special reactor cores were created using all three types of fuel elements, among them, the coupled fast-thermal ones. Nuclear Safety Committee of the Vinca Institute, an independent regulatory body approved for usage all these modifications of the RB reactor. For those decisions of the Committee, the Preliminary Safety Analysis Reports were prepared that, beside proposed technical modifications and new regulation rules had included analyses of various possible accidents. Special attention is given and new methodology was proposed for thoroughly analyses of design based accidents related to coupled fast-thermal cores, that include reactor central zones filled by fuel elements without moderator. In these accidents, during assumed flooding of the fast zone by moderator, a very high reactivity could be inserted in the system with very high reactivity rate. It was necessary to provide that the safety system of the reactor had fast response to that accident and had enough high (negative) reactivity to shut down the reactor timely. In this paper, a brief overview of some accidents, methodology and computation tools used for the accident analyses at RB reactor are given. (author)

Severe accident sequences simulated at the Grand Gulf Nuclear Station

International Nuclear Information System (INIS)

Carbajo, J.J.

1999-01-01

Different severe accident sequences employing the MELCOR code, version 1.8.4 QK, have been simulated at the Grand Gulf Nuclear Station (Grand Gulf). The postulated severe accidents simulated are two low-pressure, short-term, station blackouts; two unmitigated small-break (SB) loss-of-coolant accidents (LOCAs) (SBLOCAs); and one unmitigated large LOCA (LLOCA). The purpose of this study was to calculate best-estimate timings of events and source terms for a wide range of severe accidents and to compare the plant response to these accidents

Review of accident analyses of RB experimental reactor

International Nuclear Information System (INIS)

Pesic, M.

2003-01-01

The RB reactor is a uranium fuel heavy water moderated critical assembly that has been put and kept in operation by the VINCA Institute of Nuclear Sciences, Belgrade, Serbia and Montenegro, since April 1958. The first complete Safety Analysis Report of the RB reactor was prepared in 1961/62; yet, the first accident analysis had been made in late 1958 with the aim to examine a power transition and the total equivalent doses received by the staff during the reactivity accident that occurred on October 15, 1958. Since 1960, the RB reactor has been modified a few times. Beside the initial natural uranium metal fuel rods, new types of fuel (TVR-S types of Russian origin) consisting of 2% enriched uranium metal and 80% enriched U0 2 , dispersed in aluminum matrix, have been available since 1962 and 1976, respectively. Modifications of the control and safety systems of the reactor were made occasionally. Special reactor cores were designed and constructed using all three types of fuel elements, as well as the coupled fast-thermal ones. The Nuclear Safety Committee of the VINCA Institute, an independent regulator)' body, approved for usage all these modifications of the RB reactor on the basis of the Preliminary Safety' Analysis Reports, which, beside proposed technical modifications and new regulation rules, included safety analyses of various possible accidents. A special attention was given (and a new safety methodology was proposed) to thorough analyses of the design-based accidents related to the coupled fast-thermal cores that included central zones of the reactor filled by the fuel elements without any moderator. In this paper, an overview of some accidents, methodologies and computation tools used for the accident analyses of the RB reactor is given. (author)

Review of accident analyses of RB experimental reactor

Directory of Open Access Journals (Sweden)

Pešić Milan P.

2003-01-01

Full Text Available The RB reactor is a uranium fuel heavy water moderated critical assembly that has been put and kept in operation by the VTNCA Institute of Nuclear Sciences, Belgrade, Serbia and Montenegro, since April 1958. The first complete Safety Analysis Report of the RB reactor was prepared in 1961/62 yet, the first accident analysis had been made in late 1958 with the aim to examine a power transition and the total equivalent doses received by the staff during the reactivity accident that occurred on October 15, 1958. Since 1960, the RB reactor has been modified a few times. Beside the initial natural uranium metal fuel rods, new types of fuel (TVR-S types of Russian origin consisting of 2% enriched uranium metal and 80% enriched UO2 dispersed in aluminum matrix, have been available since 1962 and 1976 respectively. Modifications of the control and safety systems of the reactor were made occasionally. Special reactor cores were designed and constructed using all three types of fuel elements as well as the coupled fast-thermal ones. The Nuclear Safety Committee of the VINĆA Institute, an independent regulatory body, approved for usage all these modifications of the RB reactor on the basis of the Preliminary Safety Analysis Reports, which, beside proposed technical modifications and new regulation rules, included safety analyses of various possible accidents. A special attention was given (and a new safety methodology was proposed to thorough analyses of the design-based accidents related to the coupled fast-thermal cores that included central zones of the reactor filled by the fuel elements without any moderator. In this paper, an overview of some accidents, methodologies and computation tools used for the accident analyses of the RB reactor is given.

Reactivity insertion accident analysis

International Nuclear Information System (INIS)

Moreira, J.M.L.; Nakata, H.; Yorihaz, H.

1990-04-01

The correct prediction of postulated accidents is the fundamental requirement for the reactor licensing procedures. Accident sequences and severity of their consequences depend upon the analysis which rely on analytical tools which must be validated against known experimental results. Present work presents a systematic approach to analyse and estimate the reactivity insertion accident sequences. The methodology is based on the CINETHICA code which solves the point-kinetics/thermohydraulic coupled equations with weighted temperature feedback. Comparison against SPERT experimental results shows good agreement for the step insertion accidents. (author) [pt

Current understanding of the sequence of events. Overview of current understanding of accident progression at Fukushima Dai-ichi

International Nuclear Information System (INIS)

Gulliford, Jim

2013-01-01

An overview of the main sequence of events, particularly the evolution of the cores in Units 1-3 was given. The presentation is based on information provided by Dr Okajima of JAEA to the June 2012 Nuclear Science Committee meeting. During the accident, conditions at the plant were such that operators were initially unable to obtain instruments readouts from the control panel and hence could not know what condition the reactors were in. (Reactor Power, Pressure, Temperature, Water height and flow rate, etc.). Subsequently, as electrical power supplies were gradually restored more data became available. In addition to the reactor data, other information from off-site measurements and from measuring stations inside the site boundary is now available, particularly for radiation dose rates in air. These types of information, combined with detailed knowledge of the plant design and operations history up to the time of the accident are being used to construct detailed computer models which simulate the behaviour of the reactor core, pressure vessel and containment during the accident sequence. This combination of detailed design/operating data, limited measured data during the accident and computer modelling allows us to construct a fairly clear picture of the accident progression. The main sequence of events (common to Units 1, 2 and 3) is summarised. The OECD/NEA is currently coordinating an international benchmark study of the accident at Fukushima Daiichi known as the BSAF Project. The objectives of this activity are to analyse and evaluate the accident progression and improve severe accident (SA) analysis methods and models. The project provides valuable additional (and corrected) data from plant measurements as well as an improved understanding of the role played by the fuel and cladding design. Based on (limited) plant data and extensive modelling analysis, we have a detailed qualitative description of the Fukushima-Daiichi accident. Further analyses of the type

Benchmark exercises on PWR level-1 PSA (step 3). Analyses of accident sequence and conclusions

International Nuclear Information System (INIS)

Niwa, Yuji; Takahashi, Hideaki.

1996-01-01

The results of level 1 PSA generate fluctuations due to the assumptions based on several engineering judgements set in the stages of PSA analysis. On the purpose of the investigation of uncertainties due to assumptions, three kinds of a standard problem, what we call benchmark exercise have been set. In this report, sensitivity studies (benchmark exercise) of sequence analyses are treated and conclusions are mentioned. The treatment of inter-system dependency would generate uncertainly of PSA. In addition, as a conclusion of the PSA benchmark exercise, several findings in the sequence analysis together with previous benchmark analyses in earlier INSS Journals are treated. (author)

Fukushima. The accident sequence and important causes. Pt. 1/3

International Nuclear Information System (INIS)

Pistner, Christoph

2013-01-01

On March 11, 2011 a strong earthquake at the east coast of Japan and a subsequent tsunami caused severe damage at the NPP site of Fukushima Daiichi. The article covers the fundamental safety aspects of the accident progress according to the state of knowledge. The principles of nuclear technology and reactor safety are summarized in order to allow the understanding of the accidental sequence. Even two years after the disaster many questions on the sequence of accident events are still open.

Accident sequence precursor events with age-related contributors

Energy Technology Data Exchange (ETDEWEB)

Murphy, G.A.; Kohn, W.E.

1995-12-31

The Accident Sequence Precursor (ASP) Program at ORNL analyzed about 14.000 Licensee Event Reports (LERs) filed by US nuclear power plants 1987--1993. There were 193 events identified as precursors to potential severe core accident sequences. These are reported in G/CR-4674. Volumes 7 through 20. Under the NRC Nuclear Plant Aging Research program, the authors evaluated these events to determine the extent to which component aging played a role. Events were selected that involved age-related equipment degradation that initiated an event or contributed to an event sequence. For the 7-year period, ORNL identified 36 events that involved aging degradation as a contributor to an ASP event. Except for 1992, the percentage of age-related events within the total number of ASP events over the 7-year period ({approximately}19%) appears fairly consistent up to 1991. No correlation between plant ape and number of precursor events was found. A summary list of the age-related events is presented in the report.

Use of probabilistic safety analyses in severe accident management

International Nuclear Information System (INIS)

Neogy, P.; Lehner, J.

1991-01-01

An important consideration in the development and assessment of severe accident management strategies is that while the strategies are often built on the knowledge base of Probabilistic Safety Analyses (PSA), they must be interpretable and meaningful in terms of the control room indicators. In the following, the relationships between PSA and severe accident management are explored using ex-vessel accident management at a PWR ice-condenser plant as an example. 2 refs., 1 fig., 3 tabs

Accident analyses on TMLB' and LOCA for KNGR using MELCOR code

Energy Technology Data Exchange (ETDEWEB)

Park, Soo Yong; Choi, Y.; Ahn, K.I

2000-11-01

Plant specific phenomenological analyses for the Korean Next Generation Reactor, using MELCOR program, are described in this report. The most important two accident sequences, a station blackout and a loss of coolant scenario, are selected. Complete coverage of corium behavior both in-vessel and ex-vessel, and the corresponding containment responses, are analyzed. The in-vessel progression includes the thermal hydraulics in the primary system, core heat up, hydrogen generation, and melt progression up to the reactor vessel breach. The ex-vessel progression describes molten corium - concrete interaction phenomena and the pressure behavior in the containment atmosphere.

Severe accident recriticality analyses (SARA)

Energy Technology Data Exchange (ETDEWEB)

Frid, W. E-mail: wiktor.frid@ski.se; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Nilsson, L.; Puska, E.K.; Sjoevall, H

2001-11-01

Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies, the following issues have been investigated in the SARA project: (1) the energy deposition in the fuel during super-prompt power burst; (2) the quasi steady-state reactor power following the initial power burst; and (3) containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality--both super-prompt power bursts and quasi steady-state power generation--for the range of parameters studied, i.e. with core uncovering and heat-up to maximum core temperatures of approximately 1800 K, and water flow rates of 45-2000 kg s{sup -1} injected into the downcomer. Since recriticality takes place in a small fraction of the core, the power densities are high, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g{sup -1}, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s{sup -1}. In most cases, however, the predicted energy deposition was smaller, below the regulatory limits for fuel failure, but close to or above recently observed thresholds for fragmentation and dispersion of high burn-up fuel. The highest calculated

Severe accident recriticality analyses (SARA)

International Nuclear Information System (INIS)

Frid, W.; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Nilsson, L.; Puska, E.K.; Sjoevall, H.

2001-01-01

Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies, the following issues have been investigated in the SARA project: (1) the energy deposition in the fuel during super-prompt power burst; (2) the quasi steady-state reactor power following the initial power burst; and (3) containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality--both super-prompt power bursts and quasi steady-state power generation--for the range of parameters studied, i.e. with core uncovering and heat-up to maximum core temperatures of approximately 1800 K, and water flow rates of 45-2000 kg s -1 injected into the downcomer. Since recriticality takes place in a small fraction of the core, the power densities are high, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g -1 , was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s -1 . In most cases, however, the predicted energy deposition was smaller, below the regulatory limits for fuel failure, but close to or above recently observed thresholds for fragmentation and dispersion of high burn-up fuel. The highest calculated quasi steady

Review of accident analyses performed at Mochovce NPP

International Nuclear Information System (INIS)

Siko, D.

2000-01-01

In this paper the review of accident analysis performed in NPP Mochovce V-1 is presented. The scope of these safety measures was defined and development in the T SSM for NPP Mochovce Nuclear Safety Improvements Report' issued in July 1995. The main objectives of these safety measures were the followings: (a) to establish the criteria for selection and classification of accidental events, as well as defining the list of initiating events to be analysed. Accident classification to the individual groups must be performed in accordance with RG 1.70 and IAEA recommendations 'Guidelines for Accidental Analysis of WWER NPP' (IAEA-EBR-WWER-01) to select boundary cases to be calculated from the scope of initiating events; (b ) to elaborate the accident analysis methodology that also includes acceptance criteria for their result evaluation, initial and boundary conditions, assumption related with the application of the single failure criteria, requirements on the analysis quality, used computer codes, as well as NPP models and input data for the accident analysis; (c) to perform the accident analysis for the Pre-operational Safety Report (POSAR); (d) to provide a synthetic report addressing the validity range of codes models and correlations, the assessment against relevant tests results, the evidence of the user qualification, the modernisation and nodding scheme for the plant and the justification of used computer codes. Analyses results showed that all acceptance criteria were met with satisfactory margin and design of the NPP Mochovce is accurate. (author)

Molten Corium-Concrete Interaction Behavior Analyses for Severe Accident Management in CANDU Reactor

International Nuclear Information System (INIS)

Choi, Y.; Kim, D. H.; Song, Y. M.

2014-01-01

After the last few severe accidents, the importance of accident management in nuclear power plants has increased. Many countries, including the United States (US) and Canada, have focused on understanding severe accidents in order to identify ways to further improve the safety of nuclear plants. It has been recognized that severe accident analyses of nuclear power plants will be beneficial in understanding plant-specific vulnerabilities during severe accidents. The objectives of this paper are to describe the molten corium behavior to identify a plant response with various concrete specific components. Accident analyses techniques using ISSAC can be useful tools for MCCI behavior in severe accident mitigation

Methodology to classify accident sequences of an Individual Plant Examination according to the severe releases for BWR type reactors

International Nuclear Information System (INIS)

Sandoval V, S.

2001-01-01

The Light Water Reactor (LWR) operation regulations require to every operating plant to perform of an Individual Plant Examination study (Ipe). One of the main purposes of an Ipe is t o gain a more quantitative understanding of the overall probabilities of core damage and fission product releases . Probabilistic Safety Analysis (PSA) methodologies and Severe Accident Analysis are used to perform Ipe studies. PSA methodologies are used to identify and analyse the set of event sequences that might originate the fission product release from a nuclear power plant; these methodologies are combinatorial in nature and generate thousands of sequences. Among other uses within an Ipe, severe accident simulations are used to determine the characteristics of the fission product release for the identified sequences and in this way, the releases can be understood and characterized. A vast amount of resources is required to simulate and analyse every Ipe sequence. This effort is unnecessary if similar sequences are grouped. The grouping scheme must achieve an efficient trade off between problem reduction and accuracy. The methodology presented in this work enables an accurate characterization and analysis of the Ipe fission product releases by using a reduced problem. The methodology encourages the use of specific plant simulations. (Author)

Severe Accident Recriticality Analyses (SARA)

Energy Technology Data Exchange (ETDEWEB)

Frid, W. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden); Hoejerup, F. [Risoe National Lab. (Denmark); Lindholm, I.; Miettinen, J.; Puska, E.K. [VTT Energy, Helsinki (Finland); Nilsson, Lars [Studsvik Eco and Safety AB, Nykoeping (Sweden); Sjoevall, H. [Teoliisuuden Voima Oy (Finland)

1999-11-01

Recriticality in a BWR has been studied for a total loss of electric power accident scenario. In a BWR, the B{sub 4}C control rods would melt and relocate from the core before the fuel during core uncovery and heat-up. If electric power returns during this time-window unborated water from ECCS systems will start to reflood the partly control rod free core. Recriticality might take place for which the only mitigating mechanisms are the Doppler effect and void formation. In order to assess the impact of recriticality on reactor safety, including accident management measures, the following issues have been investigated in the SARA project: 1. the energy deposition in the fuel during super-prompt power burst, 2. the quasi steady-state reactor power following the initial power burst and 3. containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core state initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality - both superprompt power bursts and quasi steady-state power generation - for the studied range of parameters, i. e. with core uncovery and heat-up to maximum core temperatures around 1800 K and water flow rates of 45 kg/s to 2000 kg/s injected into the downcomer. Since the recriticality takes place in a small fraction of the core the power densities are high which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal/g, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding

Severe Accident Recriticality Analyses (SARA)

International Nuclear Information System (INIS)

Frid, W.; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Puska, E.K.; Nilsson, Lars; Sjoevall, H.

1999-11-01

Recriticality in a BWR has been studied for a total loss of electric power accident scenario. In a BWR, the B 4 C control rods would melt and relocate from the core before the fuel during core uncovery and heat-up. If electric power returns during this time-window unborated water from ECCS systems will start to reflood the partly control rod free core. Recriticality might take place for which the only mitigating mechanisms are the Doppler effect and void formation. In order to assess the impact of recriticality on reactor safety, including accident management measures, the following issues have been investigated in the SARA project: 1. the energy deposition in the fuel during super-prompt power burst, 2. the quasi steady-state reactor power following the initial power burst and 3. containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core state initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality - both superprompt power bursts and quasi steady-state power generation - for the studied range of parameters, i. e. with core uncovery and heat-up to maximum core temperatures around 1800 K and water flow rates of 45 kg/s to 2000 kg/s injected into the downcomer. Since the recriticality takes place in a small fraction of the core the power densities are high which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal/g, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding

Break spectrum analyses for small break loss of coolant accidents in a RESAR-3S Plant

International Nuclear Information System (INIS)

Fletcher, C.D.; Kullberg, C.M.

1986-03-01

A series of thermal-hydraulic analyses were performed to investigate phenomena occurring during small break loss-of-coolant-accident (LOCA) sequences in a RESAR-3S pressurized water reactor. The analysis included simulations of plant behavior using the TRAC-PF1 and RELAP5/MOD2 computer codes. Series of calculations were performed using both codes for different break sizes. The analyses presented here also served an audit function in that the results shown here were used by the US Nuclear Regulatory Commission (NRC) as an independent confirmation of similar analyses performed by Westinghouse Electric Company using another computer code. 10 refs., 62 figs., 14 tabs

Radiological consequence analyses of loss of coolant accidents of various break sizes of Pressurized Heavy Water Reactor

International Nuclear Information System (INIS)

Sanyasi Rao, V.V.S.; Hari Prasad, M.; Ghosh, A.K.

2010-01-01

For any advanced technology, it is essential to ensure that the consequences associated with the accident sequences arising, if any, from the operation of the plant are as low as possible and certainly below the guidelines/limits set by the regulatory bodies. Nuclear power is no exception to this. In this paper consequences of the events arising from Loss of Coolant Accident (LOCA) sequences in Pressurized Heavy Water Reactor (PHWR), are analysed. The sequences correspond to different break sizes of LOCA followed by the operation or otherwise of Emergency Core Cooling System (ECCS). Operation or otherwise of the containment safety systems has also been considered. It has been found that there are no releases to the environment when ECCS is available. The releases, when ECCS is not available, arise from the slack and the ground. The radionuclides considered include noble gases, iodine, and cesium. The hourly meteorological parameters (wind speed, wind direction, precipitation and stability category), considered for this study, correspond to those of Kakrapar site. The consequences evaluated are the thyroid dose and the bone marrow dose received by a person located at various distances from the release point. Isodose curves are generated. From these evaluations, it has been found that the doses are very low. The complementary cumulative frequency distributions (CCFD) for thyroid and bone marrow doses have also been presented for the cases analysed. (author)

Human factors review for nuclear power plant severe accident sequence analysis

International Nuclear Information System (INIS)

Krois, P.A.; Haas, P.M.

1985-01-01

The paper discusses work conducted to: (1) support the severe accident sequence analysis of a nuclear power plant transient based on an assessment of operator actions, and (2) develop a descriptive model of operator severe accident management. Operator actions during the transient are assessed using qualitative and quantitative methods. A function-oriented accident management model provides a structure for developing technical operator guidance on mitigating core damage preventing radiological release

Accident sequence precursor analysis level 2/3 model development

International Nuclear Information System (INIS)

Lui, C.H.; Galyean, W.J.; Brownson, D.A.

1997-01-01

The US Nuclear Regulatory Commission's Accident Sequence Precursor (ASP) program currently uses simple Level 1 models to assess the conditional core damage probability for operational events occurring in commercial nuclear power plants (NPP). Since not all accident sequences leading to core damage will result in the same radiological consequences, it is necessary to develop simple Level 2/3 models that can be used to analyze the response of the NPP containment structure in the context of a core damage accident, estimate the magnitude of the resulting radioactive releases to the environment, and calculate the consequences associated with these releases. The simple Level 2/3 model development work was initiated in 1995, and several prototype models have been completed. Once developed, these simple Level 2/3 models are linked to the simple Level 1 models to provide risk perspectives for operational events. This paper describes the methods implemented for the development of these simple Level 2/3 ASP models, and the linkage process to the existing Level 1 models

Calculation methods for analysing nuclear power plant accidents and its qualification

International Nuclear Information System (INIS)

Sacco, W.

1986-01-01

A methodology of transient and accident analyses able to carried out calculations for all transients and accidents required to support operation and operation licensing of Angra-1 reactor reload, is presented. (M.C.K.) [pt

Accident Sequence Evaluation Program: Human reliability analysis procedure

International Nuclear Information System (INIS)

Swain, A.D.

1987-02-01

This document presents a shortened version of the procedure, models, and data for human reliability analysis (HRA) which are presented in the Handbook of Human Reliability Analysis With emphasis on Nuclear Power Plant Applications (NUREG/CR-1278, August 1983). This shortened version was prepared and tried out as part of the Accident Sequence Evaluation Program (ASEP) funded by the US Nuclear Regulatory Commission and managed by Sandia National Laboratories. The intent of this new HRA procedure, called the ''ASEP HRA Procedure,'' is to enable systems analysts, with minimal support from experts in human reliability analysis, to make estimates of human error probabilities and other human performance characteristics which are sufficiently accurate for many probabilistic risk assessments. The ASEP HRA Procedure consists of a Pre-Accident Screening HRA, a Pre-Accident Nominal HRA, a Post-Accident Screening HRA, and a Post-Accident Nominal HRA. The procedure in this document includes changes made after tryout and evaluation of the procedure in four nuclear power plants by four different systems analysts and related personnel, including human reliability specialists. The changes consist of some additional explanatory material (including examples), and more detailed definitions of some of the terms. 42 refs

Development of a system of computer codes for severe accident analyses and its applications

Energy Technology Data Exchange (ETDEWEB)

Chang, Soon Hong; Cheon, Moon Heon; Cho, Nam jin; No, Hui Cheon; Chang, Hyeon Seop; Moon, Sang Kee; Park, Seok Jeong; Chung, Jee Hwan [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

1991-12-15

The objectives of this study is to develop a system of computer codes for postulated severe accident analyses in Nuclear Power Plants. This system of codes is necessary to conduct individual plant examination for domestic nuclear power plants. As a result of this study, one can conduct severe accident assessments more easily, and can extract the plant-specific vulnerabilities for severe accidents and at the same time the ideas for enhancing overall accident resistance. The scope and contents of this study are as follows : development of a system of computer codes for severe accident analyses, development of severe accident management strategy.

Development of a system of computer codes for severe accident analyses and its applications

International Nuclear Information System (INIS)

Chang, Soon Hong; Cheon, Moon Heon; Cho, Nam jin; No, Hui Cheon; Chang, Hyeon Seop; Moon, Sang Kee; Park, Seok Jeong; Chung, Jee Hwan

1991-12-01

The objectives of this study is to develop a system of computer codes for postulated severe accident analyses in Nuclear Power Plants. This system of codes is necessary to conduct individual plant examination for domestic nuclear power plants. As a result of this study, one can conduct severe accident assessments more easily, and can extract the plant-specific vulnerabilities for severe accidents and at the same time the ideas for enhancing overall accident resistance. The scope and contents of this study are as follows : development of a system of computer codes for severe accident analyses, development of severe accident management strategy

An analysis of LOCA sequences in the development of severe accident analysis DB

International Nuclear Information System (INIS)

Choi, Young; Park, Soo Yong; Ahn, Kwang-Il; Kim, D.H.

2006-01-01

Although a Level 2 PSA was performed for the Korean Standard Power Plants (KSNPs), and it considered the necessary sequences for an assessment of the containment integrity and source term analysis. In terms of an accident management, however, more cases causing severe core damage need to be analyzed and arranged systematically for an easy access to the results. At present, KAERI is calculating the severe accident sequences intensively for various initiating events and generating a database for the accident progression including thermal hydraulic and source term behaviours. The developed Database (DB) system includes a graphical display for a plant and equipment status, previous research results by knowledge-base technique, and the expected plant behaviour. The plant model used in this paper is oriented to the case of LOCAs related severe accident phenomena and thus can simulate the plant behaviours for a severe accident. Therefore the developed system may play a central role as an information source for decision-making for a severe accident management, and will be used as a training simulator for a severe accident management. (author)

Method for improving accident sequence recognition in nuclear power plant control rooms

International Nuclear Information System (INIS)

Heising, C.D.; Dinsmore, S.C.

1983-01-01

This work adapts fault trees from plant-specific probabilistic risk analyses (PRAs) to construct and quantitatively evaluate an alarm analysis system for the engineered safety features (ESFs). The purpose is to help improve reactor operator recognition and identification of potential accident sequences. The PRA system fault trees provide system failure mode information which can be used to construct alarm trees. These alarm trees provide a framework for assessing the plant indicators so that the plant conditions are made more readily apparent to plant personnel. In the alarm tree, possible states of each instrumented alarem are identified as true or false. In addition, a warning status is defined and integrated into an alarm analysis routine. The impact of this additional status conditioned on the Boolean laws used to evaluate the alarm trees is examined. An application is described for BWR high pressure coolant injection system (HPCI) that would be utilized during many severe reactor accidents

Quantitative risk trends deriving from PSA-based event analyses. Analysis of results from U.S.NRC's accident sequence precursor program

International Nuclear Information System (INIS)

Watanabe, Norio

2004-01-01

The United States Nuclear Regulatory Commission (U.S.NRC) has been carrying out the Accident Sequence Precursor (ASP) Program to identify and categorize precursors to potential severe core damage accident sequences using the probabilistic safety assessment (PSA) technique. The ASP Program has identified a lot of risk significant events as precursors that occurred at U.S. nuclear power plants. Although the results from the ASP Program include valuable information that could be useful for obtaining and characterizing risk significant insights and for monitoring risk trends in nuclear power industry, there are only a few attempts to determine and develop the trends using the ASP results. The present study examines and discusses quantitative risk trends for the industry level, using two indicators, that is, the occurrence frequency of precursors and the annual core damage probability, deriving from the results of the ASP analysis. It is shown that the core damage risk at U.S. nuclear power plants has been lowered and the likelihood of risk significant events has been remarkably decreasing. As well, the present study demonstrates that two risk indicators used here can provide quantitative information useful for examining and monitoring the risk trends and/or risk characteristics in nuclear power industry. (author)

Accident Sequence Evaluation Program: Human reliability analysis procedure

Energy Technology Data Exchange (ETDEWEB)

Swain, A.D.

1987-02-01

This document presents a shortened version of the procedure, models, and data for human reliability analysis (HRA) which are presented in the Handbook of Human Reliability Analysis With emphasis on Nuclear Power Plant Applications (NUREG/CR-1278, August 1983). This shortened version was prepared and tried out as part of the Accident Sequence Evaluation Program (ASEP) funded by the US Nuclear Regulatory Commission and managed by Sandia National Laboratories. The intent of this new HRA procedure, called the ''ASEP HRA Procedure,'' is to enable systems analysts, with minimal support from experts in human reliability analysis, to make estimates of human error probabilities and other human performance characteristics which are sufficiently accurate for many probabilistic risk assessments. The ASEP HRA Procedure consists of a Pre-Accident Screening HRA, a Pre-Accident Nominal HRA, a Post-Accident Screening HRA, and a Post-Accident Nominal HRA. The procedure in this document includes changes made after tryout and evaluation of the procedure in four nuclear power plants by four different systems analysts and related personnel, including human reliability specialists. The changes consist of some additional explanatory material (including examples), and more detailed definitions of some of the terms. 42 refs.

Event sequence quantification for a loss of shutdown cooling accident in the GCFR

International Nuclear Information System (INIS)

Frank, M.; Reilly, J.

1979-10-01

A summary is presented of the core-wide sequence of events of a postulated total loss of forced and natural convection decay heat removal in a shutdown Gas-Cooled Fast Reactor (GCFR). It outlines the analytical methods and results for the progression of the accident sequence. This hypothetical accident proceeds in the distinct phases of cladding melting, assembly wall melting and molten steel relocation into the interassembly spacing, and fuel relocation. It identifies the key phenomena of the event sequence and the concerns and mechanisms of both recriticality and recriticality prevention

Analyses of containment loading by hydrogen burning during hypothetical core meltdown accidents

International Nuclear Information System (INIS)

Bracht, K.; Tiltmann, M.

1983-01-01

The possibility of occurance of violent hydrogen burning during a LWR meltdown accident and its consequences to containment atmosphere conditions are discussed. Two accident sequences with low and high system pressure during the in-vessel-melt phase of a meltdown accident are considered. In both sequences only deflagration, but no detonation may become possible, presuming homogeneity of the containment atmospheres. In a low pressure szenario the pressure increase due to deflagration will not reach the failure pressure of the containment, if combustion takes place when the flammability limit is reached. For the special situation of a rapid release of steam and hydrogen after a high-pressure failure of a reactor pressure vessel, calculations with a multicompartment code show that the possibility for hydrogen burning does not exist. Thus, an additional augmentation of the steam spike as a consequence of the failure of the pressure vessel cannot occur. (orig.)

Steady-state and accident analyses of PBMR with the computer code SPECTRA

International Nuclear Information System (INIS)

Stempniewicz, Marek M.

2002-01-01

The SPECTRA code is an accident analysis code developed at NRG. It is designed for thermal-hydraulic analyses of nuclear or conventional power plants. The code is capable of analysing the whole power plant, including reactor vessel, primary system, various control and safety systems, containment and reactor building. The aim of the work presented in this paper was to prepare a preliminary thermal-hydraulic model of PBMR for SPECTRA, and perform steady state and accident analyses. In order to assess SPECTRA capability to model the PBMR reactors, a model of the INCOGEN system has been prepared first. Steady state and accident scenarios were analyzed for INCOGEN configuration. Results were compared to the results obtained earlier with INAS and OCTOPUS/PANTHERMIX. A good agreement was obtained. Results of accident analyses with PBMR model showed qualitatively good results. It is concluded that SPECTRA is a suitable tool for analyzing High Temperature Reactors, such as INCOGEN or for example PBMR (Pebble Bed Modular Reactor). Analyses of INCOGEN and PBMR systems showed that in all analyzed cases the fuel temperatures remained within the acceptable limits. Consequently there is no danger of release of radioactivity to the environment. It may be concluded that those are promising designs for future safe industrial reactors. (author)

Accident management approach in Armenia

International Nuclear Information System (INIS)

Ghazaryan, K.

1999-01-01

In this lecture the accident management approach in Armenian NPP (ANPP) Unit 2 is described. List of BDBAs had been developed by OKB Gydropress in 1994. 13 accident sequences were included in this list. The relevant analyses had been performed in VNIIAES and the 'Guidelines on operator actions for beyond design basis accident (BDBA) management at ANPP Unit 2' had been prepared. These instructions are discussed

Analyses of systems availability and operator actions to support the development of severe accident procedures

International Nuclear Information System (INIS)

Lutz, R.J. Jr.; Scobel, J.H.

1989-01-01

This paper reports on traditional analyses of severe accidents, such as those presented in Probabilistic Risk Assessment (PRA) studies of nuclear power stations, that have generally been performed on the assumption that all means of cooling the reactor core are lost and that no operator actions to mitigate the consequences or progression of the severe accident are performed. The assumption to neglect the availability of safety systems and operator actions which do not prevent core melting can lead to erroneous conclusions regarding the plant severer accident profile. Recent work in severe accident management has identified the need to perform analyses which consider all systems availabilities and operator actions, irrespective of their contribution to the prevention of core melting. These new analyses indicate that the traditional analyses result in overfly pessimistic predictions of the time of core melting and the subsequent potential for recovery of core cooling prior to core melting. Additionally, since the traditional analyses do not model all of the operator actions which are prescribed, the impact of additional severe accident operator actions on the progression and consequences of the accident cannot be reliably identified. Further, the more detailed analysis can change the focus of the importance of various system to the prevention of core damage and the mitigation of severe accident consequences. Finally, the simplicity of the traditional analyses can have a considerable impact on severe accident decision making, particularly in the evaluation of alternate plant design features and the priorities for research studies

Source terms associated with two severe accident sequences in a 900 MWe PWR

International Nuclear Information System (INIS)

Fermandjian, J.; Evrard, J.M.; Berthion, Y.; Lhiaubet, G.; Lucas, M.

1983-12-01

Hypothetical accidents taken into account in PWR risk assessment result in fission product release from the fuel, transfer through the primary circuit, transfer into the reactor containment building (RCB) and finally release to the environment. The objective of this paper is to define the characteristics of the source term (noble gases, particles and volatile iodine forms) released from the reactor containment building during two dominant core-melt accident sequences: S 2 CD and TLB according to the ''Reactor Safety Study'' terminology. The reactor chosen for this study is a French 900 MWe PWR unit. The reactor building is a prestressed concrete containment with an internal liner. The first core-melt accident sequence is a 2-break loss-of-coolant accident on the cold leg, with failure of both system and the containment spray system. The second one is a transient initiated by a loss of offsite and onsite power supply and auxiliary feedwater system. These two sequences have been chosen because they are representative of risk dominant scenarios. Source terms associated with hypothetical core-melt accidents S 2 CD and TLB in a French PWR -900 MWe- have been performed using French computer codes (in particular, JERICHO Code for containment response analysis and AEROSOLS/31 for aerosol behavior in the containment)

A decision theoretic approach to an accident sequence: when feedwater and auxiliary feedwater fail in a nuclear power plant

International Nuclear Information System (INIS)

Svenson, Ola

1998-01-01

This study applies a decision theoretic perspective on a severe accident management sequence in a processing industry. The sequence contains loss of feedwater and auxiliary feedwater in a boiling water nuclear reactor (BWR), which necessitates manual depressurization of the reactor pressure vessel to enable low pressure cooling of the core. The sequence is fast and is a major contributor to core damage in probabilistic risk analyses (PRAs) of this kind of plant. The management of the sequence also includes important, difficult and fast human decision making. The decision theoretic perspective, which is applied to a Swedish ABB-type reactor, stresses the roles played by uncertainties about plant state, consequences of different actions and goals during the management of a severe accident sequence. Based on a theoretical analysis and empirical simulator data the human error probabilities in the PRA for the plant are considered to be too small. Recommendations for how to improve safety are given and they include full automation of the sequence, improved operator training, and/or actions to assist the operators' decision making through reduction of uncertainties, for example, concerning water/steam level for sufficient cooling, time remaining before insufficient cooling level in the tank is reached and organizational cost-benefit evaluations of the events following a false alarm depressurization as well as the events following a successful depressurization at different points in time. Finally, it is pointed out that the approach exemplified in this study is applicable to any accident scenario which includes difficult human decision making with conflicting goals, uncertain information and with very serious consequences

Identification and evaluation of accident sequences in nuclear power reactors

International Nuclear Information System (INIS)

Amendola, A.; Capobianchi, S.; Mancini, G.; Olivi, L.; Volta, G.; Reina, G.

1981-01-01

Probabilistic analysis techniques are being more and more used for the evaluation of accident progression in nuclear power plants, especially after the issue of the Reactor Safety Study (Report WASH-1400). This study and subsequent discussions have indicated the necessity of better investigating some major items, namely: adequate data base for the probabilistic evaluations; completeness of the analysis with respect both to accident initiation and behaviour; adequate treatment of uncertainties on the physical and operational parameters governing the accident behaviour. Furthermore, recent occurrences have stressed the importance of the operational aspects of reactor safety, such as plant-specific identification of possible occurrences, their prompt recognition, on-line prediction of subsequent developments and actions to be taken. The paper reviews the contributions in progress at JRC-Ispra to all these aspects, and specifically reports on the following: (1) The set-up of a European Reliability Data System for the acquisition and organisation of operational data of LWRs in the European Community. (2) The development of more complete and realistic models of systems. This work includes multistate static models of components and systems with a view to automatic fault-tree construction and dynamic models for accident sequence identification. The dynamic modelling approach ESCS (Event Sequence and Consequences Spectrum), shown in detail with an example, represents a step forward with respect to event-tree technique and opens new possibilities in dealing with human factors and on-line diagnosis problems. (3) The development of RSM (Response Surface Methodology) for the analysis of uncertainty propagations in consequence and in probability of accident chains. (author)

Probabilistic Dynamics for Integrated Analysis of Accident Sequences considering Uncertain Events

Directory of Open Access Journals (Sweden)

Robertas Alzbutas

2015-01-01

Full Text Available The analytical/deterministic modelling and simulation/probabilistic methods are used separately as a rule in order to analyse the physical processes and random or uncertain events. However, in the currently used probabilistic safety assessment this is an issue. The lack of treatment of dynamic interactions between the physical processes on one hand and random events on the other hand causes the limited assessment. In general, there are a lot of mathematical modelling theories, which can be used separately or integrated in order to extend possibilities of modelling and analysis. The Theory of Probabilistic Dynamics (TPD and its augmented version based on the concept of stimulus and delay are introduced for the dynamic reliability modelling and the simulation of accidents in hybrid (continuous-discrete systems considering uncertain events. An approach of non-Markovian simulation and uncertainty analysis is discussed in order to adapt the Stimulus-Driven TPD for practical applications. The developed approach and related methods are used as a basis for a test case simulation in view of various methods applications for severe accident scenario simulation and uncertainty analysis. For this and for wider analysis of accident sequences the initial test case specification is then extended and discussed. Finally, it is concluded that enhancing the modelling of stimulated dynamics with uncertainty and sensitivity analysis allows the detailed simulation of complex system characteristics and representation of their uncertainty. The developed approach of accident modelling and analysis can be efficiently used to estimate the reliability of hybrid systems and at the same time to analyze and possibly decrease the uncertainty of this estimate.

Prediction of accident sequence probabilities in a nuclear power plant due to earthquake events

International Nuclear Information System (INIS)

Hudson, J.M.; Collins, J.D.

1980-01-01

This paper presents a methodology to predict accident probabilities in nuclear power plants subject to earthquakes. The resulting computer program accesses response data to compute component failure probabilities using fragility functions. Using logical failure definitions for systems, and the calculated component failure probabilities, initiating event and safety system failure probabilities are synthesized. The incorporation of accident sequence expressions allows the calculation of terminal event probabilities. Accident sequences, with their occurrence probabilities, are finally coupled to a specific release category. A unique aspect of the methodology is an analytical procedure for calculating top event probabilities based on the correlated failure of primary events

Analyses of non-fatal accidents in an opencast mine by logistic regression model - a case study.

Science.gov (United States)

Onder, Seyhan; Mutlu, Mert

2017-09-01

Accidents cause major damage for both workers and enterprises in the mining industry. To reduce the number of occupational accidents, these incidents should be properly registered and carefully analysed. This study efficiently examines the Aegean Lignite Enterprise (ELI) of Turkish Coal Enterprises (TKI) in Soma between 2006 and 2011, and opencast coal mine occupational accident records were used for statistical analyses. A total of 231 occupational accidents were analysed for this study. The accident records were categorized into seven groups: area, reason, occupation, part of body, age, shift hour and lost days. The SPSS package program was used in this study for logistic regression analyses, which predicted the probability of accidents resulting in greater or less than 3 lost workdays for non-fatal injuries. Social facilities-area of surface installations, workshops and opencast mining areas are the areas with the highest probability for accidents with greater than 3 lost workdays for non-fatal injuries, while the reasons with the highest probability for these types of accidents are transporting and manual handling. Additionally, the model was tested for such reported accidents that occurred in 2012 for the ELI in Soma and estimated the probability of exposure to accidents with lost workdays correctly by 70%.

Phenomenological uncertainty analysis of containment building pressure load caused by severe accident sequences

International Nuclear Information System (INIS)

Park, S.Y.; Ahn, K.I.

2014-01-01

Highlights: • Phenomenological uncertainty analysis has been applied to level 2 PSA. • The methodology provides an alternative to simple deterministic analyses and sensitivity studies. • A realistic evaluation provides a more complete characterization of risks. • Uncertain parameters of MAAP code for the early containment failure were identified. - Abstract: This paper illustrates an application of a severe accident analysis code, MAAP, to the uncertainty evaluation of early containment failure scenarios employed in the containment event tree (CET) model of a reference plant. An uncertainty analysis of containment pressure behavior during severe accidents has been performed for an optimum assessment of an early containment failure model. The present application is mainly focused on determining an estimate of the containment building pressure load caused by severe accident sequences of a nuclear power plant. Key modeling parameters and phenomenological models employed for the present uncertainty analysis are closely related to the in-vessel hydrogen generation, direct containment heating, and gas combustion. The basic approach of this methodology is to (1) develop severe accident scenarios for which containment pressure loads should be performed based on a level 2 PSA, (2) identify severe accident phenomena relevant to an early containment failure, (3) identify the MAAP input parameters, sensitivity coefficients, and modeling options that describe or influence the early containment failure phenomena, (4) prescribe the likelihood descriptions of the potential range of these parameters, and (5) evaluate the code predictions using a number of random combinations of parameter inputs sampled from the likelihood distributions

Accident management information needs

International Nuclear Information System (INIS)

Hanson, D.J.; Ward, L.W.; Nelson, W.R.; Meyer, O.R.

1990-04-01

In support of the US Nuclear Regulatory Commission (NRC) Accident Management Research Program, a methodology has been developed for identifying the plant information needs necessary for personnel involved in the management of an accident to diagnose that an accident is in progress, select and implement strategies to prevent or mitigate the accident, and monitor the effectiveness of these strategies. This report describes the methodology and presents an application of this methodology to a Pressurized Water Reactor (PWR) with a large dry containment. A risk-important severe accident sequence for a PWR is used to examine the capability of the existing measurements to supply the necessary information. The method includes an assessment of the effects of the sequence on the measurement availability including the effects of environmental conditions. The information needs and capabilities identified using this approach are also intended to form the basis for more comprehensive information needs assessment performed during the analyses and development of specific strategies for use in accident management prevention and mitigation. 3 refs., 16 figs., 7 tabs

Accident management information needs

Energy Technology Data Exchange (ETDEWEB)

Hanson, D.J.; Ward, L.W.; Nelson, W.R.; Meyer, O.R. (EG and G Idaho, Inc., Idaho Falls, ID (USA))

1990-04-01

In support of the US Nuclear Regulatory Commission (NRC) Accident Management Research Program, a methodology has been developed for identifying the plant information needs necessary for personnel involved in the management of an accident to diagnose that an accident is in progress, select and implement strategies to prevent or mitigate the accident, and monitor the effectiveness of these strategies. This report describes the methodology and presents an application of this methodology to a Pressurized Water Reactor (PWR) with a large dry containment. A risk-important severe accident sequence for a PWR is used to examine the capability of the existing measurements to supply the necessary information. The method includes an assessment of the effects of the sequence on the measurement availability including the effects of environmental conditions. The information needs and capabilities identified using this approach are also intended to form the basis for more comprehensive information needs assessment performed during the analyses and development of specific strategies for use in accident management prevention and mitigation. 3 refs., 16 figs., 7 tabs.

Review of Ontario Hydro Pickering 'A' and Bruce 'A' nuclear generating stations' accident analyses

International Nuclear Information System (INIS)

Serdula, K.J.

1988-01-01

Deterministic safety analysis for the Pickering 'A' and Bruce 'A' nuclear generating stations were reviewed. The methodology used in the evaluation and assessment was based on the concept of 'N' critical parameters defining an N-dimensional safety parameter space. The reviewed accident analyses were evaluated and assessed based on their demonstrated safety coverage for credible values and trajectories of the critical parameters within this N-dimensional safety parameter space. The reported assessment did not consider probability of occurrence of event. The reviewed analyses were extensive for potential occurrence of accidents under normal steady-state operating conditions. These analyses demonstrated an adequate assurance of safety for the analyzed conditions. However, even for these reactor conditions, items have been identified for consideration of review and/or further study, which would provide a greater assurance of safety in the event of an accident. Accident analyses based on a plant in a normal transient operating state or in an off-normal condition but within the allowable operating envelope are not as extensive. Improvements in demonstrations and/or justifications of safety upon potential occurrence of accidents would provide further assurance of adequacy of safety under these conditions. Some events under these conditions have not been analyzed because of their judged low probability; however, accident analyses in this area should be considered. Recommendations are presented relating to these items; it is also recommended that further study is needed of the Pickering 'A' special safety systems

Analysis of accident sequences and source terms at waste treatment and storage facilities for waste generated by U.S. Department of Energy Waste Management Operations, Volume 3: Appendixes C-H

International Nuclear Information System (INIS)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.

1995-04-01

This report contains the Appendices for the Analysis of Accident Sequences and Source Terms at Waste Treatment and Storage Facilities for Waste Generated by the U.S. Department of Energy Waste Management Operations. The main report documents the methodology, computational framework, and results of facility accident analyses performed as a part of the U.S. Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies are assessed, and the resultant radiological and chemical source terms are evaluated. A personal computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for calculation of human health risk impacts. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also provide discussion of specific accident analysis data and guidance used or consulted in this report

Analysis of accident sequences and source terms at waste treatment and storage facilities for waste generated by U.S. Department of Energy Waste Management Operations, Volume 3: Appendixes C-H

Energy Technology Data Exchange (ETDEWEB)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J. [and others

1995-04-01

This report contains the Appendices for the Analysis of Accident Sequences and Source Terms at Waste Treatment and Storage Facilities for Waste Generated by the U.S. Department of Energy Waste Management Operations. The main report documents the methodology, computational framework, and results of facility accident analyses performed as a part of the U.S. Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies are assessed, and the resultant radiological and chemical source terms are evaluated. A personal computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for calculation of human health risk impacts. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also provide discussion of specific accident analysis data and guidance used or consulted in this report.

Safety demonstration analyses for severe accident of fresh nuclear fuel transport packages at JAERI

International Nuclear Information System (INIS)

Yamada, K.; Watanabe, K.; Nomura, Y.; Okuno, H.; Miyoshi, Y.

2004-01-01

It is expected in the near future that more and more fresh nuclear fuel will be transported in a variety of transport packages to cope with increasing demand from nuclear fuel cycle facilities. Accordingly, safety demonstration analyses of these methods are planned and conducted at JAERI under contract with the Ministry of Economy, Trade and Industry of Japan. These analyses are conducted part of a four year plan from 2001 to 2004 to verify integrity of packaging against leakage of radioactive material in the case of a severe accident envisioned to occur during transportation, for the purpose of gaining public acceptance of such nuclear fuel activities. In order to create the accident scenarios, actual transportation routes were surveyed, accident or incident records were tracked, international radioactive material transport regulations such as IAEA rules were investigated and, thus, accident conditions leading to mechanical damage and thermal failure were selected for inclusion in the scenario. As a result, the worst-case conditions of run-off-the-road accidents were incorporated, where there is impact against a concrete or asphalt surface. Fire accidents were assumed to occur after collision with a tank truck carrying lots of inflammable material or destruction by fire after collision inside a tunnel. The impact analyses were performed by using three-dimensional elements according to the general purpose impact analysis code LS-DYNA. Leak-tightness of the package was maintained even in the severe impact accident scenario. In addition, the thermal analyses were performed by using two-dimensional elements according to the general purpose finite element method computer code ABAQUS. As a result of these analyses, the integrity of the inside packaging component was found to be sufficient to maintain a leak-tight state, confirming its safety

Calculation code used in criticality analyses for the accident of JCO precipitation tank

International Nuclear Information System (INIS)

Miyoshi, Yoshinori

2000-01-01

In order to evaluate nuclear features on criticality accident formed at the nuclear fuel processing facility in Tokai Works of the JCO, Ltd. (JCO), in Tokai-mura, Ibaraki prefecture, dynamic analyses to calculate output change after occurring the accident as well as criticality analyses to calculate reactivity added to precipitation tank, were carried out according to scenario on accident formation. For the criticality analyses, a continuous energy Monte Carlo code MCNP was used to carry out calculation of reactivity fed into the precipitation tank as correctly as possible. And, SRAC code system was used for calculation on temperature and void reactivity coefficients, effective delayed neutron ratio beta eff , and instantaneous neutron generation time required for parameters controlling transition features at criticality accident. In addition, for the dynamic analyses, because of necessity of considering on volume expansion of solution fuels used as exothermic body and radiation decomposition gas forming into solution, output behavior, numbers of nuclear fission, and so forth at initial burst portion were calculated by using TRACE and quasi-regular code, at a center of AGNES-2 promoting on its development in JAERI. Here were reported on outlines and an analysis example on calculation code using for the nuclear features evaluation. (G.K.)

Development of an accident sequence precursor methodology and its application to significant accident precursors

Energy Technology Data Exchange (ETDEWEB)

Jang, Seung Hyun; Park, Sung Hyun; Jae, Moo Sung [Dept. of of Nuclear Engineering, Hanyang University, Seoul (Korea, Republic of)

2017-03-15

The systematic management of plant risk is crucial for enhancing the safety of nuclear power plants and for designing new nuclear power plants. Accident sequence precursor (ASP) analysis may be able to provide risk significance of operational experience by using probabilistic risk assessment to evaluate an operational event quantitatively in terms of its impact on core damage. In this study, an ASP methodology for two operation mode, full power and low power/shutdown operation, has been developed and applied to significant accident precursors that may occur during the operation of nuclear power plants. Two operational events, loss of feedwater and steam generator tube rupture, are identified as ASPs. Therefore, the ASP methodology developed in this study may contribute to identifying plant risk significance as well as to enhancing the safety of nuclear power plants by applying this methodology systematically.

Preliminary Analysis of Aircraft Loss of Control Accidents: Worst Case Precursor Combinations and Temporal Sequencing

Science.gov (United States)

Belcastro, Christine M.; Groff, Loren; Newman, Richard L.; Foster, John V.; Crider, Dennis H.; Klyde, David H.; Huston, A. McCall

2014-01-01

Aircraft loss of control (LOC) is a leading cause of fatal accidents across all transport airplane and operational classes, and can result from a wide spectrum of hazards, often occurring in combination. Technologies developed for LOC prevention and recovery must therefore be effective under a wide variety of conditions and uncertainties, including multiple hazards, and their validation must provide a means of assessing system effectiveness and coverage of these hazards. This requires the definition of a comprehensive set of LOC test scenarios based on accident and incident data as well as future risks. This paper defines a comprehensive set of accidents and incidents over a recent 15 year period, and presents preliminary analysis results to identify worst-case combinations of causal and contributing factors (i.e., accident precursors) and how they sequence in time. Such analyses can provide insight in developing effective solutions for LOC, and form the basis for developing test scenarios that can be used in evaluating them. Preliminary findings based on the results of this paper indicate that system failures or malfunctions, crew actions or inactions, vehicle impairment conditions, and vehicle upsets contributed the most to accidents and fatalities, followed by inclement weather or atmospheric disturbances and poor visibility. Follow-on research will include finalizing the analysis through a team consensus process, defining future risks, and developing a comprehensive set of test scenarios with correlation to the accidents, incidents, and future risks. Since enhanced engineering simulations are required for batch and piloted evaluations under realistic LOC precursor conditions, these test scenarios can also serve as a high-level requirement for defining the engineering simulation enhancements needed for generating them.

Internal event analysis for Laguna Verde Unit 1 Nuclear Power Plant. Accident sequence quantification and results

International Nuclear Information System (INIS)

Huerta B, A.; Aguilar T, O.; Nunez C, A.; Lopez M, R.

1994-01-01

The Level 1 results of Laguna Verde Nuclear Power Plant PRA are presented in the I nternal Event Analysis for Laguna Verde Unit 1 Nuclear Power Plant, CNSNS-TR 004, in five volumes. The reports are organized as follows: CNSNS-TR 004 Volume 1: Introduction and Methodology. CNSNS-TR4 Volume 2: Initiating Event and Accident Sequences. CNSNS-TR 004 Volume 3: System Analysis. CNSNS-TR 004 Volume 4: Accident Sequence Quantification and Results. CNSNS-TR 005 Volume 5: Appendices A, B and C. This volume presents the development of the dependent failure analysis, the treatment of the support system dependencies, the identification of the shared-components dependencies, and the treatment of the common cause failure. It is also presented the identification of the main human actions considered along with the possible recovery actions included. The development of the data base and the assumptions and limitations in the data base are also described in this volume. The accident sequences quantification process and the resolution of the core vulnerable sequences are presented. In this volume, the source and treatment of uncertainties associated with failure rates, component unavailabilities, initiating event frequencies, and human error probabilities are also presented. Finally, the main results and conclusions for the Internal Event Analysis for Laguna Verde Nuclear Power Plant are presented. The total core damage frequency calculated is 9.03x 10-5 per year for internal events. The most dominant accident sequences found are the transients involving the loss of offsite power, the station blackout accidents, and the anticipated transients without SCRAM (ATWS). (Author)

Analysing The Thermalhydraulic Parameters Of VVER-1000 Reactor For The Accident Of Steam Generator Tube Rupture

International Nuclear Information System (INIS)

Luu Nam Hai; Truong Cong Thang

2011-01-01

To ensure the safety operation of nuclear power plant (NPP), a lot of postulated accident scenarios were considered and analysed. This research chose and analysed the accident of steam generator tube rupture (SGTR) under the actual plant conditions by using the simulation program PCTRAN. The SGTR accident is happen when the NPP is under operation with the steady state condition (power of 3000 MWth, primary pressure of 157 bar and secondary pressure of 63 bar). The accident is initiated by creating a break with equivalent diameter of 100 mm in the area of lower row heat exchanging tubes. The result of analysis is compared with the calculation of the Shariz University, Iran using the thermal hydraulics code RELAP5/mod3.2 and the report in the PSAR data of VVER-1000. This comparison shows that it is possible for using PCTRAN to analyse accidents of VVER-1000 reactor. (author)

Addressing severe accidents in the CANDU 9 design

International Nuclear Information System (INIS)

Nijhawan, S.M.; Wight, A.L.; Snell, V.G.

1998-01-01

CANDU 9 is a single-unit evolutionary heavy-water reactor based on the Bruce/Darlington plants. Severe accident issues are being systematically addressed in CANDU 9, which includes a number of unique features for prevention and mitigation of severe accidents. A comprehensive severe accident program has been formulated with feedback from potential clients and the Canadian regulatory agency. Preliminary Probabilistic Safety Analyses have identified the sequences and frequency of system and human failures that may potentially lead to initial conditions indicating onset of severe core damage. Severe accident consequence analyses have used these sequences as a guide to assess passive heat sinks for the core, and containment performance. Estimates of the containment response to mass and energy injections typical of postulated severe accidents have been made and the results are presented. We find that inherent CANDU severe accident mitigation features, such as the presence of large water volumes near the fuel (moderator and shield tank), permit a relatively slow severe accident progression under most plant damage states, facilitate debris coolability and allow ample time for the operator to arrest the progression within, progressively, the fuel channels, calandria vessel or shield tank. The large-volume CANDU 9 containment design complements these features because of the long times to reach failure

Long-Term Station Blackout Accident Analyses of a PWR with RELAP5/MOD3.3

Directory of Open Access Journals (Sweden)

Andrej Prošek

2013-01-01

Full Text Available Stress tests performed in Europe after accident at Fukushima Daiichi also required evaluation of the consequences of loss of safety functions due to station blackout (SBO. Long-term SBO in a pressurized water reactor (PWR leads to severe accident sequences, assuming that existing plant means (systems, equipment, and procedures are used for accident mitigation. Therefore the main objective was to study the accident management strategies for SBO scenarios (with different reactor coolant pumps (RCPs leaks assumed to delay the time before core uncovers and significantly heats up. The most important strategies assumed were primary side depressurization and additional makeup water to reactor coolant system (RCS. For simulations of long term SBO scenarios, including early stages of severe accident sequences, the best estimate RELAP5/MOD3.3 and the verified input model of Krško two-loop PWR were used. The results suggest that for the expected magnitude of RCPs seal leak, the core uncovery during the first seven days could be prevented by using the turbine-driven auxiliary feedwater pump and manually depressurizing the RCS through the secondary side. For larger RCPs seal leaks, in general this is not the case. Nevertheless, the core uncovery can be significantly delayed by increasing RCS depressurization.

Safety demonstration analyses at JAERI for severe accident during overland transport of fresh nuclear fuel

International Nuclear Information System (INIS)

Nomura, Yasushi; Kitao, Kohichi; Karasawa, Kiyonori; Yamada, Kenji; Takahashi, Satoshi; Watanabe, Kohji; Okuno, Hiroshi; Miyoshi, Yoshinori

2005-01-01

It is expected in the near future that more and more fresh nuclear fuel will be transported in a variety of transport packages to cope with increasing demand from nuclear fuel cycle facilities. Accordingly, safety demonstration analyses are planned and conducted at JAERI under contract with the Ministry of Economy, Trade and Industry of Japan. These analyses are conducted in a four year plan from 2001 to 2004 to verify integrity of packaging against leakage of radioactive material in the case of a severe accident postulated to occur during transportation, for the purpose of gaining acceptance of such nuclear fuel activities. In order to create the accident scenarios, actual transportation routes were surveyed, accident or incident records were tracked, international radioactive material transport regulations such as IAEA rules were investigated and thus, accident conditions leading to mechanical damages and thermal failure were determined to characterize the scenarios. As a result, the worst-case conditions of run-off-the-road accidents were set up to define the impact against a concrete or asphalt surface. For fire accident scenarios to be set up, collisions were assumed to occur with an oil tanker carrying lots of inflammable material in open air, or with a commonly used two-ton-truck inside a tunnel without ventilation. Then the cask models were determined for these safety demonstration analyses to represent those commonly used for fresh nuclear fuel transported throughout Japan. Following the postulated accident scenarios, the mechanical damages were analyzed by using the general-purpose finite element code LS-DYNA with three-dimensional elements. It was found that leak tightness of the package be maintained even in the severe impact scenario. Then the thermal safety was analyzed by using the general-purpose finite element code ABAOUS with three-dimensional elements to describe cask geometry. As a result of the thermal analyses, the integrity of the containment

SWR-1000 concept on control of severe accidents

International Nuclear Information System (INIS)

Meyer, P.J.

1998-01-01

It is essential for the SWR-1000 probabilistic safety concept to consider the results from experiments and reliability system failure within the probabilistic safety analyses for passive systems. Active and passive safety features together reduce the probability of the occurrence of beyond design basis accidents in order to limit their consequences in accordance with the German law. As a reference case we analyzed the most probable core melt accident sequence with a very conservative assumption. An initial event, stuck open of safety and relief valves without the probability of active and passive feeding systems of the pressure vessel, was considered. Other sequences of the loss of coolant accidents lead to lower probability

Radionuclide release calculations for selected severe accident scenarios

International Nuclear Information System (INIS)

Denning, R.S.; Leonard, M.T.; Cybulskis, P.; Lee, K.W.; Kelly, R.F.; Jordan, H.; Schumacher, P.M.; Curtis, L.A.

1990-08-01

This report provides the results of source term calculations that were performed in support of the NUREG-1150 study. ''Severe Accident Risks: An Assessment for Five US Nuclear Power Plants.'' This is the sixth volume of a series of reports. It supplements results presented in the earlier volumes. Analyses were performed for three of the NUREG-1150 plants: Peach Bottom, a Mark I, boiling water reactor; Surry, a subatmospheric containment, pressurized water reactor; and Sequoyah, an ice condenser containment, pressurized water reactor. Complete source term results are presented for the following sequences: short term station blackout with failure of the ADS system in the Peach Bottom plant; station blackout with a pump seal LOCA for the Surry plant; station blackout with a pump seal LOCA in the Sequoyah plant; and a very small break with loss of ECC and spray recirculation in the Sequoyah plant. In addition, some partial analyses were performed which did not require running all of the modules of the Source Term Code Package. A series of MARCH3 analyses were performed for the Surry and Sequoyah plants to evaluate the effects of alternative emergency operating procedures involving primary and secondary depressurization on the progress of the accident. Only thermal-hydraulic results are provided for these analyses. In addition, three accident sequences were analyzed for the Surry plant for accident-induced failure of steam generator tubes. In these analyses, only the transport of radionuclides within the primary system and failed steam generator were examined. The release of radionuclides to the environment is presented for the phase of the accident preceding vessel meltthrough. 17 refs., 176 figs., 113 tabs

Analysis of accident sequences and source terms at treatment and storage facilities for waste generated by US Department of Energy waste management operations

Energy Technology Data Exchange (ETDEWEB)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.; Folga, S.; Policastro, A.; Freeman, W.; Jackson, R.; Mishima, J.; Turner, S.

1996-12-01

This report documents the methodology, computational framework, and results of facility accident analyses performed for the US Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies assessed, and the resultant radiological and chemical source terms evaluated. A personal-computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for the calculation of human health risk impacts. The WM PEIS addresses management of five waste streams in the DOE complex: low-level waste (LLW), hazardous waste (HW), high-level waste (HLW), low-level mixed waste (LLMW), and transuranic waste (TRUW). Currently projected waste generation rates, storage inventories, and treatment process throughputs have been calculated for each of the waste streams. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated, and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. Key assumptions in the development of the source terms are identified. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also discuss specific accident analysis data and guidance used or consulted in this report.

Development of severe accident evaluation technology (level 2 PSA) for sodium-cooled fast reactors. (5) Identification of dominant factors in ex-vessel accident sequences

International Nuclear Information System (INIS)

Ohno, Shuji; Seino, Hiroshi; Miyahara, Shinya

2009-01-01

The evaluation of accident progression outside of a reactor vessel (ex-vessel) and subsequent transfer behavior of radioactive materials is of great importance from the viewpoint of Level 2 PSA. Hence typical ex-vessel accident sequences in the JAEA Sodium-cooled Fast Reactor are qualitatively discussed in this paper and dominant behaviors or factors in the sequences are investigated through parametric calculations using the CONTAIN/LMR code. Scenarios to be focused on are, 1) sodium vapor leakage from the reactor vessel and 2) sodium-concrete reaction, which are both to be considered in the accident category of LOHRS (loss of heat removal system) and might be followed by an early containment failure due to the thermal effect of sodium combustion and hydrogen burning respectively. The calculated results clarify that the sodium vapor leak rate and the scale of sodium-concrete reaction are the important factors to dominate the ex-vessel accident progression. In addition to the understandings of the dominant factors, the analyzed results also provide the specific information such as pressure loading value to the containment and the timing of pressurization, which is indispensable as technical base in Level 2 PSA for developing event trees and for quantifying the accident consequences. (author)

The Accident Sequence Precursor program: Methods improvements and current results

International Nuclear Information System (INIS)

Minarick, J.W.; Manning, F.M.; Harris, J.D.

1987-01-01

Changes in the US NRC Accident Sequence Precursor program methods since the initial program evaluations of 1969-81 operational events are described, along with insights from the review of 1984-85 events. For 1984-85, the number of significant precursors was consistent with the number observed in 1980-81, dominant sequences associated with significant events were reasonably consistent with PRA estimates for BWRs, but lacked the contribution due to small-break LOCAs previously observed and predicted in PWRs, and the frequency of initiating events and non-recoverable system failures exhibited some reduction compared to 1980-81. Operational events which provide information concerning additional PRA modeling needs are also described

Core damage frequency estimation using accident sequence precursor data: 1990-1993

International Nuclear Information System (INIS)

Martz, H.F.

1998-01-01

The Nuclear Regulatory Commission's (NRC's) ongoing Accident Sequence Precursor (ASP) program uses probabilistic risk assessment (PRA) techniques to assess the potential for severe core damage (henceforth referred to simply as core damage) based on operating events. The types of operating events considered include accident sequence initiators, safety equipment failures, and degradation of plant conditions that could increase the probability that various postulated accident sequences occur. Such operating events potentially reduce the margin of safety available for prevention of core damage an thus can be considered as precursors to core damage. The current process for identifying, analyzing, and documenting ASP events is described in detail in Vanden Heuval et al. The significance of a Licensee Event Report (LER) event (or events) is measured by means of the conditional probability that the event leads to core damage, the so-called conditional core damage probability or, simply, CCDP. When the first ASP study results were published in 1982, it covered the period 1969--1979. In addition to identification and ranking of precursors, the original study attempted to estimate core damage frequency (CDF) based on the precursor events. The purpose of this paper is to compare the average annual CDF estimates calculated using the CCDP sum, Cooke-Goossens, Bier, and Abramson estimators for various reactor classes using the combined ASP data for the four years, 1990--1993. An important outcome of this comparison is an answer to the persistent question regarding the degree and effect of the positive bias of the CCDP sum method in practice. Note that this paper only compares the estimators with each other. Because the true average CDF is unknown, the estimation error is also unknown. Therefore, any observations or characterizations of bias are based on purely theoretical considerations

Analyses of conditions in a large, dry PWR containment during an TMLB' accident sequence

International Nuclear Information System (INIS)

Sweet, D.W.; Roberts, G.J.

1994-01-01

The aim of the paper is to give an assessment of the conditions which would develop in the large, dry containment of a modern Westinghouse-type PWR during a severe accident where all safety systems are unavailable. The analysis is based principally on the results of calculations using the CONTAIN code, with a 4 cell model of the containment, for a station blackout (TMLB') scenario in which the vessel is assumed to fail at high pressure. In particular, the following are noted: (i) If much of the debris is in contact with water, so that decay heat can boil water directly, then the pressure rises steadily to reach the assumed containment failure point after 11/2 to 2 days. If most of the debris becomes isolated from water, for example, because of water is held up on the containment floors and in sumps and drains, the pressure rises too slowly to threaten the containment on this timescale. (ii) If a core-concrete interaction occurs, most of the associated fission product release takes place soon after relocation of molten fuel to the containment. The aerosols which transport these (and other non-gaseous fission products released earlier in the accident) in the containment agglomerate and settle. As a result, 0.1% or less of the aerosols remain airborne a day after the start of the accident. (iii) Hydrogen and carbon monoxide, which would accumulate in the containment are not expected to burn because the atmosphere would be inerted by steam. If, however, enough of the steam is condensed, for example, by recovering the containment sprays, a burn could occur but the resulting pressure spike is unlikely to threaten the containment unless a transition to detonation occurs. 6 refs., 6 tabs., 12 figs

The CIEMAT’s forensic analyses of Fukushima accident: Contribution to the BSAF project

Energy Technology Data Exchange (ETDEWEB)

Herranz, L.E.; López, C.; Fontanet, J.; Fernández, E.

2015-07-01

The Fukushima accident is being both a unique opportunity and a huge challenge for severe accident analysis. Through the simulation of the accidents in Units 1 through 3 with MELCOR 2.1, three scenarios have been postulated which outcomes look consistent with data. These analyses indicate that a massive core damage should have happened in Unit 1, with most core molten and located in the containment, whereas Units 2 and 3 core damage is anticipated to be much less; however, there might be differences among these “twin” units. Anyway, in all the units the amount of H2 produced is over 500 kg. This work has been carried out in the frame of the international project for the understanding of the severe accidents occurred at Fukushima, the OECD-BSAF project. (Author)

Impact of sophisticated fog spray models on accident analyses

International Nuclear Information System (INIS)

Roblyer, S.P.; Owzarski, P.C.

1978-01-01

The N-Reactor confinement system release dose to the public in a postulated accident is reduced by washing the confinement atmosphere with fog sprays. This allows a low pressure release of confinement atmosphere containing fission products through filters and out an elevated stack. The current accident analysis required revision of the CORRAL code and other codes such as CONTEMPT to properly model the N Reactor confinement into a system of multiple fog-sprayed compartments. In revising these codes, more sophisticated models for the fog sprays and iodine plateout were incorporated to remove some of the conservatism of steam condensing rate, fission product washout and iodine plateout than used in previous studies. The CORRAL code, which was used to describe the transport and deposition of airborne fission products in LWR containment systems for the Rasmussen Study, was revised to describe fog spray removal of molecular iodine (I 2 ) and particulates in multiple compartments for sprays having individual characteristics of on-off times, flow rates, fall heights, and drop sizes in changing containment atmospheres. During postulated accidents, the code determined the fission product removal rates internally rather than from input decontamination factors. A discussion is given of how the calculated plateout and washout rates vary with time throughout the analysis. The results of the accident analyses indicated that more credit could be given to fission product washout and plateout. An important finding was that the release of fission products to the atmosphere and adsorption of fission products on the filters were significantly lower than previous studies had indicated

Methodology for the Assessment of Confidence in Safety Margin for Small Break Loss of Coolant Accident Sequences

Energy Technology Data Exchange (ETDEWEB)

Nagrale, D. B.; Prasad, M.; Rao, R. S.; Gaikwad, A.J., E-mail: avinashg@aerb.gov.in [Nuclear Safety Analysis Division, Atomic Energy Regulatory Board, Mumbai (India)

2014-10-15

Deterministic Safety Analysis and Probabilistic Safety Assessment (PSA) analyses are used concurrently to assess the Nuclear Power Plant (NPP) safety. The conventional deterministic analysis is conservative. The best estimate plus uncertainty analysis is increasingly being used for deterministic calculation in NPPs. The PSA methodology aims to be as realistic as possible while integrating information about accident phenomena, plant design, operating practices, component reliability and human behaviour. The peak clad temperature (PCT) distribution provides an insight into the confidence in safety margin for an initiating event. The paper deals with the concept of calculating the peak clad temperature with 95 percent confidence and 95 percent probability (PCT{sub 95/95}) in small break loss of coolant accident (SBLOCA) and methodologies for assessing safety margin. Five input parameters mainly, nominal power level, decay power, fuel clad gap conductivity, fuel thermal conductivity and discharge coefficient, were selected. A Uniform probability density function was assigned to the uncertain parameters and these uncertainties are propagated using Latin Hypercube Sampling (LHS) technique. The sampled data for 5 parameters were randomly mixed by LHS to obtain 25 input sets. A non-core damage accident sequence was selected from the SBLOCA event tree of a typical VVER study to estimate the PCTs and safety margin. A Kolmogorov– Smirnov goodness-of-fit test was carried out for PCTs. The smallest value of safety margin would indicate the robustness of the system with 95% confidence and 95% probability. Regression analysis was also carried out using 1000 sample size for the estimating PCTs. Mean, variance and finally safety margin were analysed. (author)

Severe accident sequence assessment for boiling water reactors: program overview

International Nuclear Information System (INIS)

Fontana, M.H.

1980-10-01

The Severe Accident Sequence Assessment (SASA) Program was started at the Oak Ridge National Laboratory (ORNL) in June 1980. This report documents the initial planning, specification of objectives, potential uses of the results, plan of attack, and preliminary results. ORNL was assigned the Brown's Ferry Unit 1 Plant with the station blackout being the initial sequence set to be addressed. This set includes: (1) loss of offsite and onsite ac power with no coolant injection; and (2) loss of offsite and onsite ac power with high pressure coolant injection (HPCI) and reactor core isolation cooling (RCIC) as long as dc power supply lasts. This report includes representative preliminary results for the former case

A direct comparison of MELCOR 1.8.3 and MAAP4 results for several PWR ampersand BWR accident sequences

International Nuclear Information System (INIS)

Leonard, M.T.; Ashbaugh, S.G.; Cole, R.K.; Bergeron, K.D.; Nagashima, K.

1996-01-01

This paper presents a comparison of calculations of severe accident progression for several postulated accident sequences for representative Pressurized Water Reactors (PWR) and Boiling Water Reactors (BWR) nuclear power plants performed with the MELCOR 1.8.3 and the MAAP4 computer codes. The PWR system examined in this study is a 1100 MWe system similar in design to a Westinghouse 3-loop plant with a large dry containment; the BWR is a 1100 MWe system similar in design to General Electric BWR/4 with a Mark I containment. A total of nine accident sequences were studied with both codes. Results of these calculations are compared to identify major differences in the timing of key events in the calculated accident progression or other important aspects of severe accident behavior, and to identify specific sources of the observed differences

Accident sequences evaluation using SFATs for low power and shutdown operation of pressurized heavy water reactors

International Nuclear Information System (INIS)

Kim, Chansoo; Chung, Chang-Hyun; Yang, Huichang

2004-01-01

To maintain the level of defense-in-depth safety of Pressurized Heavy Water Reactor (PHWR) during LP/SD operation, the qualitative risk evaluation methods such as Safety Function Assessment Trees (SFATs) are required. Therefore SFATs are suggested to assess and manage the PHWR safety in LP/SD. Before this study, safety functions of PHWR were classified into 7 groups; Reactivity Control, Core Cooling, Secondary Heat Removal, Primary Heat Transport Inventory, Essential Electrical Power, Cooling Water, and Containment Integrity. The SFATs for PHWR LP/SD operations were developed along with the Plant Outage Status (POS) variation, and totally 38 SFATs were developed for Wolsung Unit 2. For the verification of SFATs logics developed, top 5 accident sequences those contribute the CDF of PHWR were selected, and plant safety status were evaluated for those accident sequences. Accident sequences such as DCC-4 (Dual Control Computer Failure), CL4-16 (Total Loss of Class IV Power), and FWPV-11 (Loss of Feedwater Supply to SG due to Failure of Pumps/Values) were included. In this research the evaluation of plant safety status by accident sequences using SFATs and the verification of the SFATs were performed. Through the verification of SFAT logics, the enhancements to the internal logics of the SFATs were made, and the dependencies between safety systems and support systems were considered. It is expected the defense-in-depth evaluation model of PHW just as SFATs can be utilized in the configuration risk management program (CRMP) development and improve technical specifications development for Korean PHWRs. (author)

Fukushima, one year after. First analyses of the accident and of its consequences

International Nuclear Information System (INIS)

2012-01-01

This report proposes assessments and discussions of knowledge gathered by the IRSN during the first twelve months following the Fukushima accident to understand the status of the installations, to assess the releases, and to analyse and assess the consequences of the accident on workers and the impact on the population and environment. After a description of a boiling water reactor (general description, confinement barriers, safeguard systems), and of the earthquake, the authors describe and comment the consequences for several reactors (Fukushima-Dai-ini, Onagawa, Tokai, Higashidoru and Hamaoka). Then, they more precisely describe the Fukushima-Dai-ichi accident by distinguishing different periods (first two weeks, next three weeks, after the 17 of April). They analyse and comment the environmental impact in Japan (atmospheric dispersion of radioactive releases, ground contamination, impact of radioactive fallouts, contamination of the marine environment, and predictable impact on marine and ground ecosystems). They describe the actions undertaken to protect the population and in terms of post-accidental management, comment assessments of the dosimetric and health impact (workers and population exposure). They finally discuss the long range impact

Report of the US Department of Energy's team analyses of the Chernobyl-4 Atomic Energy Station accident sequence

International Nuclear Information System (INIS)

1986-11-01

In an effort to better understand the Chernobyl-4 accident of April 26, 1986, the US Department of Energy (DOE) formed a team of experts from the National Laboratories including Argonne National Laboratory, Brookhaven National Laboratory, Oak Ridge National Laboratory, and Pacific Northwest Laboratory. The DOE Team provided the analytical support to the US delegation for the August meeting of the International Atomic Energy Agency (IAEA), and to subsequent international meetings. The DOE Team has analyzed the accident in detail, assessed the plausibility and completeness of the information provided by the Soviets, and performed studies relevant to understanding the accident. The results of these studies are presented in this report

Airborne concentrations of radioactive materials in severe accidents

International Nuclear Information System (INIS)

Ross, D.F. Jr.; Denning, R.S.

1989-01-01

Radioactive materials would be released to the containment building of a commercial nuclear reactor during each of the stages of a severe accident. Results of analyses of two accident sequences are used to illustrate the magnitudes of these sources of radioactive materials, the resulting airborne mass concentrations, the characteristics of the airborne aerosols, the potential for vapor forms of radioactive materials, the effectiveness of engineered safety features in reducing airborne concentrations, and the release of radioactive materials to the environment. Ability to predict transport and deposition of radioactive materials is important to assessing the performance of containment safety features in severe accidents and in the development of accident management procedures to reduce the consequences of severe accidents

Application of ASTEC V2.0 to severe accident analyses for German KONVOI type reactors

International Nuclear Information System (INIS)

Nowack, H.; Erdmann, W.; Reinke, N.

2011-01-01

The integral code ASTEC is jointly developed by IRSN (Institut de Radioprotection et de Surete Nucleaire, France) and GRS (Germany). Its main objective is to simulate severe accident scenarios in PWRs from the initiating event up to the release of radioactive material into the environment. This paper describes the ASTEC modeling approach and the nodalisation of a KONVOI type PWR as an application example. Results from an integral severe accident study are presented and shortcomings as well as advantages are outlined. As a conclusion, the applicability of ASTEC V2.0 for deterministic severe accident analyses used for PSA level 2 and Severe Accident Management studies will be assessed. (author)

Analyses to demonstrate the structural performance of the CASTOR KN12 in hypothetical accident drop accident scenarios

International Nuclear Information System (INIS)

Diersch, R.; Weiss, M.; Tso, C.F.; Chung, S.H.; Lee, H.Y.

2004-01-01

CASTORc ircledR KN-12 is a new cask design by GNB for KHNP-NETEC for dry and wet transportation of up to twelve spent PWR fuel assemblies in Korea. It received its transport license from the Korean Competent Authority KINS in July 2002 and is now in use in South Korea. It has been designed to satisfy the regulatory requirements of the 10 CFR 71 and the IAEA ST-1 for Type B(U)F packages. Its structural performance was demonstrated against the load cases and boundary conditions as defined in 10 CFR 71 and NRC's Regulatory Guide 7.8, and further explained in NUREG 1617. This included normal conditions of transport load cases - including Hot Environment, Cold Environment, Increased External Pressure (140MPa), Minimum External Pressure (24.5kPa), Vibration and shock, and 0.3m free drop - and the hypothetical accident conditions load cases - including the 9m Free Drop, Puncture, Thermal Fire Accident, 200m Water Immersion and 1.5 x MNOP Internal Pressure. Structural performance were demonstrated by analysis, including state-of-the-art finite element (FE) simulation, and confirmed by tests using a 1/3-scale model. Test results were also used to verify the numerical tool and the methods used in the analyses. All the structural analyses including validation against drop tests were carried out by Arup, and testing were carried out by KAERI. This paper concentrates on the analysis carried out to demonstrate performance in the hypothetical accident 9m free drop scenarios, and results from a small selection of them

Analyses to demonstrate the structural performance of the CASTOR KN12 in hypothetical accident drop accident scenarios

Energy Technology Data Exchange (ETDEWEB)

Diersch, R.; Weiss, M. [Gesellschaft fuer Nuklear-Behaelter mbH (Germany); Tso, C.F. [Arup (United Kingdom); Chung, S.H.; Lee, H.Y. [KHNP-NETEC (Korea)

2004-07-01

CASTORc{sup ircledR} KN-12 is a new cask design by GNB for KHNP-NETEC for dry and wet transportation of up to twelve spent PWR fuel assemblies in Korea. It received its transport license from the Korean Competent Authority KINS in July 2002 and is now in use in South Korea. It has been designed to satisfy the regulatory requirements of the 10 CFR 71 and the IAEA ST-1 for Type B(U)F packages. Its structural performance was demonstrated against the load cases and boundary conditions as defined in 10 CFR 71 and NRC's Regulatory Guide 7.8, and further explained in NUREG 1617. This included normal conditions of transport load cases - including Hot Environment, Cold Environment, Increased External Pressure (140MPa), Minimum External Pressure (24.5kPa), Vibration and shock, and 0.3m free drop - and the hypothetical accident conditions load cases - including the 9m Free Drop, Puncture, Thermal Fire Accident, 200m Water Immersion and 1.5 x MNOP Internal Pressure. Structural performance were demonstrated by analysis, including state-of-the-art finite element (FE) simulation, and confirmed by tests using a 1/3-scale model. Test results were also used to verify the numerical tool and the methods used in the analyses. All the structural analyses including validation against drop tests were carried out by Arup, and testing were carried out by KAERI. This paper concentrates on the analysis carried out to demonstrate performance in the hypothetical accident 9m free drop scenarios, and results from a small selection of them.

Containment response to a severe accident (TMLB sequence) with and without mitigation strategies

International Nuclear Information System (INIS)

Passalacqua, R.

2004-01-01

A loss of SG feed-water (TMLB sequence) for a prototypic PWR 900 MWe with a multi-compartment configuration (with 11 and 16 cells nodalization) has been calculated by the author using the ASTEC code in the frame of the EVITA project (5th Framework Programme, FWP). A variety of hypothesis (e.g. activation of sprays and hydrogen recombiners) and possible consequences of these assumptions (cavity flooding, hydrogen combustion, etc.) have been made in order to evaluate the global reactor containment building response (pressure, aerosol/FP concentration, etc.). The need to dispose of severe accident management guidelines (SAMGs) is increasing. These guidelines are meant for nuclear plants' operators in order to allow them to apply mitigation strategies all along a severe accident, which, only in its initial phase, may last several days. The purpose of this paper is to outline the influence on the containment load of most common accident occurrences and operators actions, which is essential in establishing SAMGs. ASTEC (Accident Source Term Evaluation Code) is a computer code for the evaluation of the consequences of a postulated nuclear plant severe accident sequence. ASTEC is a computer tool currently under joint development by the Institut de Radioprotection et de Surete Nucleaire (IRSN), France, and Gesellschaft fuer Anlagen-und Reaktorsicherheit (GRS), Germany. The aim of the development is to create a fast running integral code package, reliable in all simulations of a severe accident, to be used for level-2 PSA analysis. It must be said that several recent developments have significantly improved the best-estimate models of ASTEC and a new version (ASTEC V1.0) has been released mid-2002. Nevertheless, the somehow obsolete ASTECv0.3 version here used, has given results very useful for the estimation of the global risk of a nuclear plant. Moreover, under the current 6th FWP (Sustainable Integration of EU Research on Severe Accident Phenomenology and Management), the

Fukushima. The accident sequence and important causes. Pt. 1/3; Fukushima. Unfallablauf und wesentliche Ursachen. T. 1/3

Energy Technology Data Exchange (ETDEWEB)

Pistner, Christoph [Oeko-Institut e.V., Darmstadt (Germany). Bereich Nukleartechnik und Anlagensicherheit

2013-07-01

On March 11, 2011 a strong earthquake at the east coast of Japan and a subsequent tsunami caused severe damage at the NPP site of Fukushima Daiichi. The article covers the fundamental safety aspects of the accident progress according to the state of knowledge. The principles of nuclear technology and reactor safety are summarized in order to allow the understanding of the accidental sequence. Even two years after the disaster many questions on the sequence of accident events are still open.

Analysis of accident sequences and source terms at waste treatment and storage facilities for waste generated by U.S. Department of Energy Waste Management Operations, Volume 1: Sections 1-9

International Nuclear Information System (INIS)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.

1995-04-01

This report documents the methodology, computational framework, and results of facility accident analyses performed for the U.S. Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies are assessed, and the resultant radiological and chemical source terms are evaluated. A personal computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for calculation of human health risk impacts. The methodology is in compliance with the most recent guidance from DOE. It considers the spectrum of accident sequences that could occur in activities covered by the WM PEIS and uses a graded approach emphasizing the risk-dominant scenarios to facilitate discrimination among the various WM PEIS alternatives. Although it allows reasonable estimates of the risk impacts associated with each alternative, the main goal of the accident analysis methodology is to allow reliable estimates of the relative risks among the alternatives. The WM PEIS addresses management of five waste streams in the DOE complex: low-level waste (LLW), hazardous waste (HW), high-level waste (HLW), low-level mixed waste (LLMW), and transuranic waste (TRUW). Currently projected waste generation rates, storage inventories, and treatment process throughputs have been calculated for each of the waste streams. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also provide discussion of specific accident analysis data and guidance used or consulted in this report

Analyses of severe accident scenarios in RBMK-1500

International Nuclear Information System (INIS)

Kaliatka, A.; Rimkevicius, S.; Uspuras, E.; Urbonavicius, E.

2006-01-01

Even though research of severe accidents in light water reactors is performed around the world for several decades many questions remain. Research is mostly performed for vessel-type reactors. RBMK is a channel type light water reactor, which differs from the vessel-type reactors in several aspects. These differences impose some specifics in the accident phenomena and processes that occur during severe accidents. Severe accident research for RBMK reactors is taking first steps and very little information is available in the open literature. The existing severe accident analysis codes are developed for vessel-type reactors and their application to the analysis of accidents in RBMK is not straightforward. This paper presents the results of an analysis of large loss-of-coolant accident scenarios with loss of coolant injection to the core of RBMK-1500. The analysis performed considers processes in the reactor core, in the reactor cooling system and in the confinement until the fuel melting started. This paper does not aim to answer all the questions regarding severe accidents in RBMK but rather to start a discussion, identify the expected timing of the key phenomena. (orig.)

Post-facta Analyses of Fukushima Accident and Lessons Learned

Energy Technology Data Exchange (ETDEWEB)

Tanabe, Fumiya [Sociotechnical Systems Safety Research Institute, Ichige (Japan)

2014-08-15

Independent analyses have been performed of the core melt behavior of the Unit 1, Unit 2 and Unit 3 reactors of Fukushima Daiichi Nuclear Power Station on 11-15 March 2011. The analyses are based on a phenomenological methodology with measured data investigation and a simple physical model calculation. Estimated are time variation of core water level, core material temperature and hydrogen generation rate. The analyses have revealed characteristics of accident process of each reactor. In the case of Unit 2 reactor, the calculated result suggests little hydrogen generation because of no steam generation in the core for zirconium-steam reaction during fuel damage process. It could be the reason of no hydrogen explosion in the Unit 2 reactor building. Analyses have been performed also on the core material behavior in another chaotic period of 19-31 March 2011, and it resulted in a re-melt hypothesis that core material in each reactor should have melted again due to shortage of cooling water. The hypothesis is consistent with many observed features of radioactive materials dispersion into the environment.

ACCIDENT ANALYSES & CONTROL OPTIONS IN SUPPORT OF THE SLUDGE WATER SYSTEM SAFETY ANALYSIS

Energy Technology Data Exchange (ETDEWEB)

WILLIAMS, J.C.

2003-11-15

This report documents the accident analyses and nuclear safety control options for use in Revision 7 of HNF-SD-WM-SAR-062, ''K Basins Safety Analysis Report'' and Revision 4 of HNF-SD-SNF-TSR-001, ''Technical Safety Requirements - 100 KE and 100 KW Fuel Storage Basins''. These documents will define the authorization basis for Sludge Water System (SWS) operations. This report follows the guidance of DOE-STD-3009-94, ''Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports'', for calculating onsite and offsite consequences. The accident analysis summary is shown in Table ES-1 below. While this document describes and discusses potential control options to either mitigate or prevent the accidents discussed herein, it should be made clear that the final control selection for any accident is determined and presented in HNF-SD-WM-SAR-062.

Small break LOCA [loss of coolant accident] mitigation for Bellefonte

International Nuclear Information System (INIS)

Bayless, P.D.; Dobbe, C.A.

1986-01-01

Several 5-cm (2-in.) diameter cold leg break loss coolant accidents for the Bellefonte nuclear plant were analyzed as part of the Severe Accident Sequence Analysis Program. The transients assumed various system failures, and included the S 2 D sequence. Operator actions to mitigate the S 2 D transient were also investigated. The transients were analyzed until either core damage began or long-term decay heat removal was established. The S 2 D sequence was analyzed into the core damage phase of the transient. The analyses showed that the flow from one high pressure injection pump was necessary and sufficient to prevent core damage in the absence of operator actions. Operator actions were also able to prevent core damage for the S 2 D sequence

Analyses d'accidents : une nécessité pour les analyses de danger et l'intervention en situation d'urgence ?

OpenAIRE

Pineau , Jean-Philippe; Abiven , Françoise; Lechaudel , Jean-François; Mavrothalassitis , Guy

1993-01-01

Lors d'accidents industriels mettant en jeu des explosions, des incendies ou des émissions de produits toxiques ou inflammables dans l'environnement, les effets à prendre en compte s'expriment en termes d'impulsions de pression, de projections de débris, de flux thermiques et de rejets de produits toxiques dans l'air, les eaux et les sols. Dans sa première partie, le présent article présente les conclusions consécutives à l'analyse de différents types d'accidents survenus en France et met en ...

Comparative accident analyses for a KONVOI-type PWR using the integral codes ASTEC V1.33 and MELCOR 1.8.6

International Nuclear Information System (INIS)

Reinke, Nils; Erdmann, Walter; Nowack, Holger; Sonnenkalb, Martin

2010-08-01

deviations appear early in the calculated accident sequences it is difficult to explain differences appearing at later stages. Hence, it is strongly advised to perform separate analyses focusing on specific phases of the accident in order to assess e.g. the models for the molten-core-concrete interactions in the cavity after reactor pressure vessel failure.

Postulated accidents

International Nuclear Information System (INIS)

Ullrich, W.

1980-01-01

This lecture on 'Postulated Accidents' is the first of a series of lectures on the dynamic and transient behaviour of nuclear power plants, especially pressurized water reactors. The main points covered will be: Reactivity Accidents, Transients (Intact Loop) and Loss of Cooland Accidents (LOCA) including small leak. This lecture will discuss the accident analysis in general, the definition of the various operational phases, the accident classification, and, as an example, an accident sequence analysis on the basis of 'Postulated Accidents'. (orig./RW)

Hazards and accident analyses, an integrated approach, for the Plutonium Facility at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Pan, P.Y.; Goen, L.K.; Letellier, B.C.; Sasser, M.K.

1995-01-01

This paper describes an integrated approach to perform hazards and accident analyses for the Plutonium Facility at Los Alamos National Laboratory. A comprehensive hazards analysis methodology was developed that extends the scope of the preliminary/process hazard analysis methods described in the AIChE Guidelines for Hazard Evaluations. Results fro the semi-quantitative approach constitute a full spectrum of hazards. For each accident scenario identified, there is a binning assigned for the event likelihood and consequence severity. In addition, each accident scenario is analyzed for four possible sectors (workers, on-site personnel, public, and environment). A screening process was developed to link the hazard analysis to the accident analysis. Specifically the 840 accident scenarios were screened down to about 15 accident scenarios for a more through deterministic analysis to define the operational safety envelope. The mechanics of the screening process in the selection of final scenarios for each representative accident category, i.e., fire, explosion, criticality, and spill, is described

Modeling framework for crew decisions during accident sequences

International Nuclear Information System (INIS)

Lukic, Y.D.; Worledge, D.H.; Hannaman, G.W.; Spurgin, A.J.

1986-01-01

The ability to model the average behavior of operating crews in the course of accident sequences is vital in learning on how to prevent damage to power plants and to maintain safety. This paper summarizes the work carried out in support of a Human Reliability Model framework. This work develops the mathematical framework of the model and identifies the parameters which could be measured in some way, e.g., through simulator experience and/or small scale tests. Selected illustrative examples are presented, of the numerical experiments carried out in order to understand the model sensitivity to parameter variation. These examples ar discussed with the objective of deriving insights of general nature regarding operating of the model which may lead to enhanced understanding of man/machine interactions

Application of the accident management information needs methodology to a severe accident sequence

International Nuclear Information System (INIS)

Ward, L.W.; Hanson, D.J.; Nelson, W.R.; Solberg, D.E.

1989-01-01

The U.S. Nuclear Regulatory Commission is conducting an accident management research program that emphasizes the use of severe accident research to enhance the ability of plant operating personnel to effectively manage severe accidents. Hence, it is necessary to ensure that the plant instrumentation and information systems adequately provide this information to the operating staff during accident conditions. A methodology to identify and assess the information needs of the operating staff of a nuclear power plant during a severe accident has been developed. The methodology identifies (a) the information needs of the plant personnel during a wide range of accident conditions, (b) the existing plant measurements capable of supplying these information needs and minor additions to instrument and display systems that would enhance management capabilities, (c) measurement capabilities and limitations during severe accident conditions, and (d) areas in which the information systems could mislead plant personnel

Application of the accident management information needs methodology to a severe accident sequence

Energy Technology Data Exchange (ETDEWEB)

Ward, L.W.; Hanson, D.J.; Nelson, W.R. (Idaho National Engineering Laboratory, Idaho Falls (USA)); Solberg, D.E. (Nuclear Regulatory Commission, Washington, DC (USA))

1989-11-01

The U.S. Nuclear Regulatory Commission is conducting an accident management research program that emphasizes the use of severe accident research to enhance the ability of plant operating personnel to effectively manage severe accidents. Hence, it is necessary to ensure that the plant instrumentation and information systems adequately provide this information to the operating staff during accident conditions. A methodology to identify and assess the information needs of the operating staff of a nuclear power plant during a severe accident has been developed. The methodology identifies (a) the information needs of the plant personnel during a wide range of accident conditions, (b) the existing plant measurements capable of supplying these information needs and minor additions to instrument and display systems that would enhance management capabilities, (c) measurement capabilities and limitations during severe accident conditions, and (d) areas in which the information systems could mislead plant personnel.

Methodology for accident analyses of fusion breeder blankets and its application to helium-cooled pebble bed blanket

International Nuclear Information System (INIS)

Panayotov, Dobromir; Grief, Andrew; Merrill, Brad J.; Humrickhouse, Paul; Trow, Martin; Dillistone, Michael; Murgatroyd, Julian T.; Owen, Simon; Poitevin, Yves; Peers, Karen; Lyons, Alex; Heaton, Adam; Scott, Richard

2016-01-01

Graphical abstract: - Highlights: • Test Blanket Systems (TBS) DEMO breeding blankets (BB) safety demonstration. • Comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials, and phenomena. • Development of accident analysis specifications (AAS) via the use of phenomena identification and ranking tables (PIRT). • PIRT application to identify required physical models for BB accidents analysis, code assessment and selection. • Development of MELCOR and RELAP5 codes TBS models. • Qualification of the models via comparison with finite element calculations, code-tocode comparisons, and sensitivity studies. - Abstract: ‘Fusion for Energy’ (F4E) is designing, developing, and implementing the European Helium-Cooled Lead-Lithium (HCLL) and Helium-Cooled Pebble-Bed (HCPB) Test Blanket Systems (TBSs) for ITER (Nuclear Facility INB-174). Safety demonstration is an essential element for the integration of these TBSs into ITER and accident analysis is one of its critical components. A systematic approach to accident analysis has been developed under the F4E contract on TBS safety analyses. F4E technical requirements, together with Amec Foster Wheeler and INL efforts, have resulted in a comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials, and phenomena while remaining consistent with the approach already applied to ITER accident analyses. The methodology phases are illustrated in the paper by its application to the EU HCPB TBS using both MELCOR and RELAP5 codes.

Methodology for accident analyses of fusion breeder blankets and its application to helium-cooled pebble bed blanket

Energy Technology Data Exchange (ETDEWEB)

Panayotov, Dobromir, E-mail: dobromir.panayotov@f4e.europa.eu [Fusion for Energy (F4E), Josep Pla, 2, Torres Diagonal Litoral B3, Barcelona E-08019 (Spain); Grief, Andrew [Amec Foster Wheeler, Booths Park, Chelford Road, Knutsford WA16 8QZ, Cheshire (United Kingdom); Merrill, Brad J.; Humrickhouse, Paul [Idaho National Laboratory, PO Box 1625, Idaho Falls, ID (United States); Trow, Martin; Dillistone, Michael; Murgatroyd, Julian T.; Owen, Simon [Amec Foster Wheeler, Booths Park, Chelford Road, Knutsford WA16 8QZ, Cheshire (United Kingdom); Poitevin, Yves [Fusion for Energy (F4E), Josep Pla, 2, Torres Diagonal Litoral B3, Barcelona E-08019 (Spain); Peers, Karen; Lyons, Alex; Heaton, Adam; Scott, Richard [Amec Foster Wheeler, Booths Park, Chelford Road, Knutsford WA16 8QZ, Cheshire (United Kingdom)

2016-11-01

Graphical abstract: - Highlights: • Test Blanket Systems (TBS) DEMO breeding blankets (BB) safety demonstration. • Comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials, and phenomena. • Development of accident analysis specifications (AAS) via the use of phenomena identification and ranking tables (PIRT). • PIRT application to identify required physical models for BB accidents analysis, code assessment and selection. • Development of MELCOR and RELAP5 codes TBS models. • Qualification of the models via comparison with finite element calculations, code-tocode comparisons, and sensitivity studies. - Abstract: ‘Fusion for Energy’ (F4E) is designing, developing, and implementing the European Helium-Cooled Lead-Lithium (HCLL) and Helium-Cooled Pebble-Bed (HCPB) Test Blanket Systems (TBSs) for ITER (Nuclear Facility INB-174). Safety demonstration is an essential element for the integration of these TBSs into ITER and accident analysis is one of its critical components. A systematic approach to accident analysis has been developed under the F4E contract on TBS safety analyses. F4E technical requirements, together with Amec Foster Wheeler and INL efforts, have resulted in a comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials, and phenomena while remaining consistent with the approach already applied to ITER accident analyses. The methodology phases are illustrated in the paper by its application to the EU HCPB TBS using both MELCOR and RELAP5 codes.

Large Break LOCA Accident Management Strategies for Accidents With Large Containment Leaks

International Nuclear Information System (INIS)

Sdouz, Gert

2006-01-01

The goal of this work is the investigation of the influence of different accident management strategies on the thermal-hydraulics in the containment during a Large Break Loss of Coolant Accident with a large containment leak from the beginning of the accident. The increasing relevance of terrorism suggests a closer look at this kind of severe accidents. Normally the course of severe accidents and their associated phenomena are investigated with the assumption of an intact containment from the beginning of the accident. This intact containment has the ability to retain a large part of the radioactive inventory. In these cases there is only a release via a very small leakage due to the un-tightness of the containment up to cavity bottom melt through. This paper represents the last part of a comprehensive study on the influence of accident management strategies on the source term of VVER-1000 reactors. Basically two different accident sequences were investigated: the 'Station Blackout'- sequence and the 'Large Break LOCA'. In a first step the source term calculations were performed assuming an intact containment from the beginning of the accident and no accident management action. In a further step the influence of different accident management strategies was studied. The last part of the project was a repetition of the calculations with the assumption of a damaged containment from the beginning of the accident. This paper concentrates on the last step in the case of a Large Break LOCA. To be able to compare the results with calculations performed years ago the calculations were performed using the Source Term Code Package (STCP), hydrogen explosions are not considered. In this study four different scenarios have been investigated. The main parameter was the switch on time of the spray systems. One of the results is the influence of different accident management strategies on the source term. In the comparison with the sequence with intact containment it was

Causal Analysis to a Subway Accident: A Comparison of STAMP and RAIB

Directory of Open Access Journals (Sweden)

Zhou Yao

2018-01-01

Full Text Available Accident investigation and analysis after the accident, vital to prevent the occurrence of similar accident and improve the safety of the system. Different methods led to a different understanding of the accident. In this paper, a subway accident was analysed with a systemic accident analysis model – STAMP (System-Theoretic Accident Modelling and Processes. The hierarchical safety control structure was obtained, and the system-level safety constraints were obtained, controllers of the physical layer were analysed one by one, and put forward the relevant safety requirements and constraints, the dynamic analysis of the structure of the safety control is carried out, and the targeted recommendations are pointed out. In comparison with the analysis results obtained by the Rail Accident Investigation Branch (RAIB. Some useful findings have been concluded. STAMP treats safety as a control problem and reduces or eliminates causes of the accident from the controlling perspective. Whereas RAIB obtains causes of the accident by analysing the sequence of events related to the accident and reasons of these events, then chooses one(or moreevent(s as the immediate cause and some of the key events as causal factors. RAIB analysis is based on the sequential event models, but STAMP analysis provides us with a holistic, dynamic way to control system to maintain safety.

Severe accident tests and development of domestic severe accident system codes

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

According to lessons learned from Fukushima-Daiichi NPS accidents, the safety evaluation will be started based on the NRA's New Safety Standards. In parallel with this movement, reinforcement of Severe Accident (SA) Measures and Accident Managements (AMs) has been undertaken and establishments of relevant regulations and standards are recognized as urgent subjects. Strengthening responses against nuclear plant hazards, as well as realistic protection measures and their standardization is also recognized as urgent subjects. Furthermore, decommissioning of Fukushima-Daiichi Unit1 through Unit4 is promoted diligently. Taking into account JNES's mission with regard to these SA Measures, AMs and decommissioning, movement of improving SA evaluation methodologies inside and outside Japan, and prioritization of subjects based on analyses of sequences of Fukushima-Daiichi NPS accidents, three viewpoints was extracted. These viewpoints were substantiated as the following three groups of R and D subjects: (1) Obtaining near term experimental subjects: Containment venting, Seawater injection, Iodine behaviors. (2) Obtaining mid and long experimental subjects: Fuel damage behavior at early phase of core degradation, Core melting and debris formation. (3) Development of a macroscopic level SA code for plant system behaviors and a mechanistic level code for core melting and debris formation. (author)

Severe accident tests and development of domestic severe accident system codes

International Nuclear Information System (INIS)

2013-01-01

According to lessons learned from Fukushima-Daiichi NPS accidents, the safety evaluation will be started based on the NRA's New Safety Standards. In parallel with this movement, reinforcement of Severe Accident (SA) Measures and Accident Managements (AMs) has been undertaken and establishments of relevant regulations and standards are recognized as urgent subjects. Strengthening responses against nuclear plant hazards, as well as realistic protection measures and their standardization is also recognized as urgent subjects. Furthermore, decommissioning of Fukushima-Daiichi Unit1 through Unit4 is promoted diligently. Taking into account JNES's mission with regard to these SA Measures, AMs and decommissioning, movement of improving SA evaluation methodologies inside and outside Japan, and prioritization of subjects based on analyses of sequences of Fukushima-Daiichi NPS accidents, three viewpoints was extracted. These viewpoints were substantiated as the following three groups of R and D subjects: (1) Obtaining near term experimental subjects: Containment venting, Seawater injection, Iodine behaviors. (2) Obtaining mid and long experimental subjects: Fuel damage behavior at early phase of core degradation, Core melting and debris formation. (3) Development of a macroscopic level SA code for plant system behaviors and a mechanistic level code for core melting and debris formation. (author)

Analysis of accident sequences and source terms at treatment and storage facilities for waste generated by US Department of Energy waste management operations. Volume 1: Sections 1-9

International Nuclear Information System (INIS)

Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.; Folga, S.; Policastro, A.; Freeman, W.; Jackson, R.; Mishima, J.; Turner, S.

1996-12-01

This report documents the methodology, computational framework, and results of facility accident analyses performed for the US Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies assessed, and the resultant radiological and chemical source terms evaluated. A personal-computer-based computational framework and database have been developed that provide these results as input to the WM PEIS for the calculation of human health risk impacts. The WM PEIS addresses management of five waste streams in the DOE complex: low-level waste (LLW), hazardous waste (HW), high-level waste (HLW), low-level mixed waste (LLMW), and transuranic waste (TRUW). Currently projected waste generation rates, storage inventories, and treatment process throughputs have been calculated for each of the waste streams. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated, and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. Key assumptions in the development of the source terms are identified. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also discuss specific accident analysis data and guidance used or consulted in this report

Severe accident analysis using MARCH 1.0 code

International Nuclear Information System (INIS)

Guimaraes, A.C.F.

1987-09-01

The description and utilization of the MARCH 1.0 computer code, which aim to analyse physical phenomena associated with core meltdown accidents in PWR type reactors, are presented. The primary system is modeled as a single volume which is partitioned into a gas (steam and hydrogen) region and a water region. March predicts blowdown from the primary system in single phase. Based on results of the probabilistic safety analysis for the Zion and Indian Point Nuclear Power Plants, the S 2 HFX sequence accident for Angra-1 reactor is studied. The S 2 HFX sequence means that the loss of coolant accident occurs through small break in primary system with bot total failures of the reactor safety system and containment in yours recirculation modes, leading the core melt and the containment failure due to overpressurization. The obtained results were considered reasonable if compared with the results obtained for the Zion and Indian Point nuclear power plants. (Author) [pt

Use of flow models to analyse loss of coolant accidents

International Nuclear Information System (INIS)

Pinet, Bernard

1978-01-01

This article summarises current work on developing the use of flow models to analyse loss-of-coolant accident in pressurized-water plants. This work is being done jointly, in the context of the LOCA Technical Committee, by the CEA, EDF and FRAMATOME. The construction of the flow model is very closely based on some theoretical studies of the two-fluid model. The laws of transfer at the interface and at the wall are tested experimentally. The representativity of the model then has to be checked in experiments involving several elementary physical phenomena [fr

Studies of potential severe accidents in Finnish nuclear power plants. Quarterly report 3. quarter 1987

International Nuclear Information System (INIS)

Aro, Ilari.

1989-07-01

This thesis is based on six publications dealing with severe accident studies in Finnish nuclear power plants. Main emphasis has been put on general technical bases and methodologies applied in severe accident evaluation in Finland. As an example of the use of the analysis and evaluation methods, the analysis of one representative accident sequence, t otal loss of AC power , has been presented for both Finnish power plant types. This accident sequence is required to be analyzed in the Finnish safety guide YVL 2.2 which deals with transient and accident analyses as a basis of technical solutions at nuclear powr plants. Two different analysis methods, MAAP 3.0 and MARCH 3/STCP have been used for receiving as complete a picture as possible of the flow of events and for verifying the models to some extent. Besides the use of the two different models, the method of sensitivity analysis has been used for evaluating the effects of some important technical parameters on the accident flow. Finally, conclusions of the applicability of the two methods for analyzing severe accident sequences in Finnish plants have been discussed

Discussion of the concept of safety indicators from the point of view of TfUX2 accident sequence for Forsmark 3

International Nuclear Information System (INIS)

Bujor, A.

1991-01-01

This paper contains general considerations on the safety indicators, with details at the system level and for the operator actions. For the system analysis, a modular analysis at a low detailed level is proposed (Module System Approach) in order to emphasize the safety related aspects at the subsystem (module) level. The operator actions are divided in ''active actions'' (actions in the control room during incident/accident situations) and ''passive actions'' (actions during tests, maintenance, repairs, etc.) and are analysed separately. In the second part, a discussion of a possible way to apply some SI to the TfUX2 accident sequence for FORSMARK-3, is done. For the analysis of the Auxiliary Feedwater Systems (AFWS) an equation is proposed to derive target values for the failure probability on demand at the train level, given the target value at the system level, including the common cause failures between the redundant trains. (author) 6 tabs., 18 refs

The next nuclear power station generation: Beyond-design accident concepts, methods, and action sequence

International Nuclear Information System (INIS)

Asmolov, V.G.; Khakh, O.Ya.; Shashkov, M.G.

1993-01-01

The problem of beyond-design accidents at nuclear stations will not be solved unless a safety culture becomes a basic characteristic of all lines of activity. Only then can the danger of accidents as an objective feature of nuclear stations be eliminated by purposive skilled and responsible activities of those implementing safety. Nuclear-station safety is provided by the following interacting and complementary lines of activity: (1) the design and construction of nuclear stations by properly qualified design and building organizations; (2) monitoring and supervision of safety by special state bodies; (3) control of the station by the exploiting organization; and (4) scientific examination of safety within the above framework and by independent organizations. The distribution of the responsibilities, powers, and right in these lines should be defined by a law on atomic energy, but there is not such law in Russian. The beyond-design accident problem is a key one in nuclear station safety, as it clear from the serious experience with accidents and numerous probabilistic studies. There are four features of the state of this topic in Russia that are of major significance for managing accidents: the lack of an atomic energy law, the inadequacy of the technical standards, the lack of a verified program package for nuclear-station designs in order to calculate the beyond-design accidents and analyze risks, and a lack of approach by designers to such accidents on the basis of international recommendations. This paper gives a brief description of three-forming points in the scientific activity: the general concept of nuclear-station safety, methods of analyzing and providing accident management, and the sequence of actions developed by specialists at this institute in recent years

Depressurization accident analyses for the Fort St. Vrain Reactor

International Nuclear Information System (INIS)

Paul, D.D.

1976-01-01

Design-basis depressurization accident analyses for the Fort St. Vrain reactor were performed using the FLODIS (Ref. 4) code. The FLODIS code models the active core, side reflector, gas annulus between the core barrel and the PCRV liner, and the PCRV cooling system. Results are presented for the Pelton circulators operating at 10,550, 8800, and 7000 rpm. Maximum temperatures of selected components are plotted as a function of time during the transient. None of the components studied exceeded the temperature at which failure or damage may occur. However, there must be sufficient mixing of the outlet gas in the lower plenum to insure the integrity of the steel liners of the steam generator inlet ducts

Release of fission products during controlled loss-of-coolant accidents and hypothetical core meltdown accidents

International Nuclear Information System (INIS)

Albrecht, H.; Malinauskas, A.P.

1978-01-01

A few years ago the Projekt Nukleare Sicherheit joined the United States Nuclear Regulatory Commission in the development of a research program which was designed to investigate fission product release from light water reactor fuel under conditions ranging from spent fuel shipping cask accidents to core meltdown accidents. Three laboratories have been involved in this cooperative effort. At Argonne National Laboratory (ANL), the research effort has focused on noble gas fission product release, whereas at Oak Ridge National Laboratory (ORNL) and at Kernforschungszentrum Karlsruhe (KfK), the studies have emphasized the release of species other than the noble gases. In addition, the ORNL program has been directed toward the development of fission product source terms applicable to analyses of spent fuel shipping cask accidents and controlled loss-of-coolant accidents, and the KfK program has been aimed at providing similar source terms which are characteristic of core meltdown accidents. The ORNL results are presented for fission product release from defected fuel rods into a steam atmosphere over the temperature range 500 to 1200 0 C, and the KfK results for release during core meltdown sequences

Loss-of-coolant accident analyses of the Advanced Neutron Source Reactor

International Nuclear Information System (INIS)

Chen, N.C.J.; Yoder, G.L.; Wendel, M.W.

1991-01-01

Currently in the conceptual design stage, the Advanced Neutron Source Reactor (ANSR) will operate at a high heat flux, a high mass flux, an a high degree of coolant subcooling. Loss-of-coolant accident (LOCA) analyses using RELAP5 have been performed as part of an early evaluation of ANSR safety issues. This paper discusses the RELAP5 ANSR conceptual design system model and preliminary LOCA simulation results. Some previous studies were conducted for the preconceptual design. 12 refs., 7 figs

Source term analyses under severe accidents for KNGR

Energy Technology Data Exchange (ETDEWEB)

Song, Yong Mann; Park, Soo Yong

2001-03-01

In this study, in-containment source term for LOFW (Loss of Feed Water), which has appeared the most frequent core melt accident, is calculated and compared with NUREG-1465 source term. This study provides not only new source term data using MELCOR1.8.4 and its state-of-the-art models but also evaluating basis of KNGR design and its mitigation capability under severe accidents. As the selected accident is identical with LOFW-S17, which has been analyzed using MAAP by KEPCO with only difference of 2 SITs, mutual comparison of the results is especially expected.

Prevention of pedestrian accidents.

OpenAIRE

Kendrick, D

1993-01-01

Child pedestrian accidents are the most common road traffic accident resulting in injury. Much of the existing work on road traffic accidents is based on analysing clusters of accidents despite evidence that child pedestrian accidents tend to be more dispersed than this. This paper analyses pedestrian accidents in 573 children aged 0-11 years by a locally derived deprivation score for the years 1988-90. The analysis shows a significantly higher accident rate in deprived areas and a dose respo...

Efficient method for simulation of BWR severe accident sequence events before core uncovery

International Nuclear Information System (INIS)

Harrington, R.M.

1984-01-01

BWR-LACP has been a versatile tool for the ORNL SASA program. The development effort was minimal, and the code is fast running and economical. Operator actions are easily simulated and the complete scope of both reactor vessel and primary containment are modeled. Valuable insights have been gained into accident sequences. A Fortran version is under development and it will be modified for application to Mark II plants

Preliminary steps towards assessing aerosol retention in the break stage of a dry steam generator during severe accident SGTR sequences

International Nuclear Information System (INIS)

Herranz, L.E.; Lopez del Pra, C.; Sanchez Velasco, F.J.

2006-01-01

Severe accidents SGTR sequences are identified as major contributors to risk of PWRs. Their relevance lies in the potential radioactive release from reactor coolant system to the environment. Lack of knowledge on the source term attenuation capability of the steam generator has avoided its consideration in probabilistic safety studies and severe accident management guidelines. This paper describes a research program presently under way on the aerosol retention in the nearby of the tube breach within the secondary side of the steam generation in the absence of water. Its development has been internationally framed within the EU-SGTR and the ARTIST program. Experimental activities are focused on setting up a reliable database in which the influence of gas mass flow rate, breach configuration and particle nature in the aerosol retention are properly considered. Theoretical activities are aimed at developing a predictive tool (ARISG) capable of assessing source term attenuation in the scenario with reasonable accuracy. Given the major importance of jet aerodynamics, 3D CFD analyses are being conducted to assist both test interpretation and model development. (author)

Status of science and technology with respect of preparation and evaluation of accident analyses and the use of analysis simulators

International Nuclear Information System (INIS)

Pointner, Winfried; Cuesta Morales, Alejandra; Draeger, Peer; Hartung, Juergen; Jakubowski, Zygmunt; Meyer, Gerhard; Palazzo, Simone; Moner, Guim Pallas; Perin, Yann; Pasichnyk, Ihor

2014-07-01

The scope of the work was to elaborate the prerequisites for short term accident analyses including recommendations for the application of new methodologies and computational procedures and technical aspects of safety evaluation. The following work packages were performed: Knowledge base for best estimate accident analyses; analytical studies on the PWR plant behavior in case of multiple safety system failures; extension and maintenance of the data base for plant specific analysis simulators.

A methodology for analysing human errors of commission in accident scenarios for risk assessment

International Nuclear Information System (INIS)

Kim, J. H.; Jung, W. D.; Park, J. K

2003-01-01

As the concern on the impact of the operator's inappropriate interventions, so-called Errors Of Commissions(EOCs), on the plant safety has been raised, the interest in the identification and analysis of EOC events from the risk assessment perspective becomes increasing accordingly. To this purpose, we propose a new methodology for identifying and analysing human errors of commission that might be caused from the failures in situation assessment and decision making during accident progressions given an initiating event. The proposed methodology was applied to the accident scenarios of YGN 3 and 4 NPPs, which resulted in about 10 EOC situations that need careful attention

Heath Effects Sequence of Meet Halfa Radiological Accident After Twelve Years

International Nuclear Information System (INIS)

Shabon, M.H.

2013-01-01

The accident of Meet-Halfa developed consequent upon the loss of an industrial gamma radiography source. The source was found by a farmer resident of Meet-Halfa who took it to his house occupied by his family. The sequence of events developed over a period of seven weeks from the time the source was found on May 5, 2000, till the day of its retrieval from the house by the national authorities on June 26. The protracted exposure patterns of the family members during the period of source possession are not precisely known, however these exposures resulted in two fatalities, clinical forms of bone marrow depression, and several skin burns of different severities. The recent sequences of the accident is as follows:-The three survived siblings married and get good children. That mean there is no hereditary stochastic effects. The sister died at 2007 with 72 years old with senility and no specific disease. The youngest daughter amputate the left thumb and index fingers at 2001. The elder son amputate the terminal phalanx of the right thumb at 2009. The youngest daughter amputate the right index finger at 2009. The elder son graft the burn at the lower right quadrant of the abdomen for more than 20 times (3 of them were in the Mansheat Al-Bakry Millitary Hospital), but there is residual of burn untill now. Sever abdominal hernia in the elder son due to necroses in the right quadrant abdominal muscles. Grafting for these muscles occur but failed.

Methodology for time-dependent reliability analysis of accident sequences and complex reactor systems

International Nuclear Information System (INIS)

Paula, H.M.

1984-01-01

The work presented here is of direct use in probabilistic risk assessment (PRA) and is of value to utilities as well as the Nuclear Regulatory Commission (NRC). Specifically, this report presents a methodology and a computer program to calculate the expected number of occurrences for each accident sequence in an event tree. The methodology evaluates the time-dependent (instantaneous) and the average behavior of the accident sequence. The methodology accounts for standby safety system and component failures that occur (a) before they are demanded, (b) upon demand, and (c) during the mission (system operation). With respect to failures that occur during the mission, this methodology is unique in the sense that it models components that can be repaired during the mission. The expected number of system failures during the mission provides an upper bound for the probability of a system failure to run - the mission unreliability. The basic event modeling includes components that are continuously monitored, periodically tested, and those that are not tested or are otherwise nonrepairable. The computer program ASA allows practical applications of the method developed. This work represents a required extension of the presently available methodology and allows a more realistic PRA of nuclear power plants

Benchmarking Severe Accident Computer Codes for Heavy Water Reactor Applications

International Nuclear Information System (INIS)

2013-12-01

Requests for severe accident investigations and assurance of mitigation measures have increased for operating nuclear power plants and the design of advanced nuclear power plants. Severe accident analysis investigations necessitate the analysis of the very complex physical phenomena that occur sequentially during various stages of accident progression. Computer codes are essential tools for understanding how the reactor and its containment might respond under severe accident conditions. The IAEA organizes coordinated research projects (CRPs) to facilitate technology development through international collaboration among Member States. The CRP on Benchmarking Severe Accident Computer Codes for HWR Applications was planned on the advice and with the support of the IAEA Nuclear Energy Department's Technical Working Group on Advanced Technologies for HWRs (the TWG-HWR). This publication summarizes the results from the CRP participants. The CRP promoted international collaboration among Member States to improve the phenomenological understanding of severe core damage accidents and the capability to analyse them. The CRP scope included the identification and selection of a severe accident sequence, selection of appropriate geometrical and boundary conditions, conduct of benchmark analyses, comparison of the results of all code outputs, evaluation of the capabilities of computer codes to predict important severe accident phenomena, and the proposal of necessary code improvements and/or new experiments to reduce uncertainties. Seven institutes from five countries with HWRs participated in this CRP

Severe accident research activities at Helmholtz-Zentrum Dresden-Rossendorf (HZDR)

Energy Technology Data Exchange (ETDEWEB)

Wilhelm, Polina; Jobst, Matthias; Schaefer, Frank; Kliem, Soeren [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany)

2016-05-15

In the frame of the nuclear safety research program of the Helmholtz Association HZDR performs fundamental and applied research to assess and to reduce the risks related to the nuclear fuel cycle and the production of electricity in nuclear power plants. One of the research topics focuses on the safety aspects of current and future reactor designs. This includes the development and application of methods for analyses of transients and postulated accidents, covering the whole spectrum from normal operation till severe accident sequences including core degradation. This paper gives an overview of the severe accident research activities at the Reactor Safety Division at the Institute of Resource Ecology.

Safety and risk questions following the nuclear incidents and accidents in Japan. Summary final report

International Nuclear Information System (INIS)

Mildenberger, Oliver

2015-03-01

After the nuclear accidents in Japan, GRS has carried out in-depth investigations of the events. On the one hand, the accident sequences in the affected units have been analysed from various viewpoints. On the other hand, the transferability of the findings to German plants has been examined to possibly make recommendations for safety improvements. The accident sequences at Fukushima Daiichi have been traced with as much detail as possible based on all available information. Additional insights have been drawn from thermohydraulic analyses with the GRS code system ATHLET-CD/COCOSYS focusing on the events in units 2 and 3, e.g. with regard to core damage and the state of the containments in the first days of the accident sequence. In-depth investigations have also been carried out on topics such as natural external hazards, electrical power supply or organizational measures. In addition, methodological studies on further topics related with the accidents have been performed. Through a detailed analysis of the relevant data from the events in Japan, the basis for an in-depth examination of the transferability to German plants was created. It was found that an implementation of most of the insights gained from the investigations had already been initiated as part of the GRS information notice 2012/02. Further findings have been communicated to the federal government and introduced into other relevant bodies, e.g. the Nuclear Safety Standards Committee (KTA) or the Reactor Safety Commission (RSK).

A PC Mathcad-based computational aid for severe accident analysis and its application to a BWR small LOCA sequence

International Nuclear Information System (INIS)

Wu, Laung-Kuang T.; Lee, S.J.

2004-01-01

A PC-based Mathcad program is used to develop a computational aid for analyzing severe accident phenomena. This computational aid uses simple engineering expressions and empirical correlations to estimate key quantities and timings at various stages of accident progressions. In this paper, the computational aid is applied to analyze an early phase of a BWR small LOCA sequence. The accident phenomena analyzed include: break flow rates, boiled-up water level in the core, core uncovery time, depressurization of the reactor pressure vessel, core heat-up, onset of clad oxidation, hydrogen generation, and onset of fuel relocation. The results are compared with those obtained running the MAAP 3.0B code. This PC-based computational aid can be used to train plant personnel in understanding severe accident phenomena and to assist them in managing severe accidents. (author)

Current and anticipated use of thermal-hydraulic codes for BWR transient and accident analyses in Japan

Energy Technology Data Exchange (ETDEWEB)

Arai, Kenji; Ebata, Shigeo [Toshiba Corp., Yokohama (Japan)

1997-07-01

This paper summarizes the current and anticipated use of the thermal-hydraulic and neutronic codes for the BWR transient and accident analyses in Japan. The codes may be categorized into the licensing codes and the best estimate codes for the BWR transient and accident analyses. Most of the licensing codes have been originally developed by General Electric. Some codes have been updated based on the technical knowledge obtained in the thermal hydraulic study in Japan, and according to the BWR design changes. The best estimates codes have been used to support the licensing calculations and to obtain the phenomenological understanding of the thermal hydraulic phenomena during a BWR transient or accident. The best estimate codes can be also applied to a design study for a next generation BWR to which the current licensing model may not be directly applied. In order to rationalize the margin included in the current BWR design and develop a next generation reactor with appropriate design margin, it will be required to improve the accuracy of the thermal-hydraulic and neutronic model. In addition, regarding the current best estimate codes, the improvement in the user interface and the numerics will be needed.

OVERVIEW OF MODULAR HTGR SAFETY CHARACTERIZATION AND POSTULATED ACCIDENT BEHAVIOR LICENSING STRATEGY

Energy Technology Data Exchange (ETDEWEB)

Ball, Sydney J [ORNL

2014-06-01

This report provides an update on modular high-temperature gas-cooled reactor (HTGR) accident analyses and risk assessments. One objective of this report is to improve the characterization of the safety case to better meet current regulatory practice, which is commonly geared to address features of today s light water reactors (LWRs). The approach makes use of surrogates for accident prevention and mitigation to make comparisons with LWRs. The safety related design features of modular HTGRs are described, along with the means for rigorously characterizing accident selection and progression methodologies. Approaches commonly used in the United States and elsewhere are described, along with detailed descriptions and comments on design basis (and beyond) postulated accident sequences.

Consequences of potential accidents in heavy water plants

International Nuclear Information System (INIS)

Croitoru, C.; Lazar, R.E.; Preda, I.A.; Dumitrescu, M.

2002-01-01

Heavy water plants achieve the primary isotopic concentration by H 2 O-H 2 S chemical exchange. In these plants are stored large quantities of hydrogen sulphide (high toxic, corrosive, flammable and explosive) maintained in process at relative high temperatures and pressures. It is required an assessment of risks associated with the potential accidents. The paper presents adopted model for quantitative consequences assessment in heavy water plants. Following five basic steps are used to identify the risks involved in plants operation: hazard identification, accident sequences development, H 2 S emissions calculus, dispersion analyses and consequences determination. A brief description of each step and some information from risk assessment for our heavy water pilot plant are provided. Accident magnitude, atmospheric conditions and population density in studied area were accounted for consequences calculus. (author)

Consequence of potential accidents in heavy water plants

International Nuclear Information System (INIS)

Croitoru, C.; Lazar, R.E.; Preda, I.A.; Dumitrescu, M.

1998-01-01

Heavy water plants realize the primary isotopic concentrations of water using H 2 O-H 2 S chemical exchange and they are chemical plants. As these plants are handling and spreading large quantities of hydrogen sulphide (high toxic, corrosive, flammable and explosive as) maintained in the process at relative high temperatures and pressures, it is required an assessing of risks associated with the potential accidents. The H 2 S released in atmosphere as a result of an accident will have negative consequences to property, population and environment. This paper presents a model of consequences quantitative assessment and its outcome for the most dangerous accident in heavy water plants. Several states of the art risk based methods were modified and linked together to form a proper model for this analyse. Five basic steps to identify the risks involved in operating the plants are followed: hazard identification, accident sequence development, H 2 S emissions calculus, dispersion analyses and consequences determination. A brief description of each step and some information of analysis results are provided. The accident proportions, the atmospheric conditions and the population density in the respective area were accounted for consequences calculus. The specific results of the consequences analysis allow to develop the plant's operating safety requirements so that the risk remain at an acceptable level. (authors)

Hypothetical accident scenario analyses for a 250-MW(t) modular high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Harrington, R.M.; Ball, S.J.; Cleveland, J.C.

1985-11-01

This paper describes calculations performed to characterize the inherent safety of a 250-MW(t), 100-MW(e), pebble bed modular high temperature gas-cooled reactor (HTGR) design with vertical in-line arrangement (i.e., upflow core with steam generators directly above the core). A variety of postulated accident sequences involving combinations of loss of forced primary coolant (helium) circulation, loss of primary coolant pressurization, and loss of heat sink were studied and were discussed

The tsunami probabilistic risk assessment (PRA). Example of accident sequence analysis of tsunami PRA according to the standard for procedure of tsunami PRA for nuclear power plants

International Nuclear Information System (INIS)

Ohara, Norihiro; Hasegawa, Keiko; Kuroiwa, Katsuya

2013-01-01

After the Fukushima Daiichi nuclear power plant (NPP) accident, standard for procedure of tsunami PRA for NPP had been established by the Standardization Committee of AESJ. Industry group had been conducting analysis of Tsunami PRA for PWR based on the standard under the cooperation with electric utilities. This article introduced overview of the standard and examples of accident sequence analysis of Tsunami PRA studied by the industry group according to the standard. The standard consisted of (1) investigation of NPP's composition, characteristics and site information, (2) selection of relevant components for Tsunami PRA and initiating events and identification of accident sequence, (3) evaluation of Tsunami hazards, (4) fragility evaluation of building and components and (5) evaluation of accident sequence. Based on the evaluation, countermeasures for further improvement of safety against Tsunami could be identified by the sensitivity analysis. (T. Tanaka)

Radiological Consequence Analyses Following a Hypothetical Severe Accident in Japan

Energy Technology Data Exchange (ETDEWEB)

Kim, Juyub; Kim, Juyoul [FNC Technology Co., Yongin (Korea, Republic of)

2016-10-15

In order to reflect the lessons learned from the Fukushima Daiichi nuclear power plant accident, a simulator which is named NANAS (Northeast Asia Nuclear Accident Simulator) for overseas nuclear accident has been developed. It is composed of three modules: source-term estimation, atmospheric dispersion prediction and dose assessment. For the source-term estimation module, the representative reactor types were selected as CPR1000, BWR5 and BWR6 for China, Japan and Taiwan, respectively. Considering the design characteristics of each reactor type, the source-term estimation module simulates the transient of design basis accident and severe accident. The atmospheric dispersion prediction module analyzes the transport and dispersion of radioactive materials and prints out the air and ground concentration. Using the concentration result, the dose assessment module calculates effective dose and thyroid dose in the Korean Peninsula region. In this study, a hypothetical severe accident in Japan was simulated to demonstrate the function of NANAS. As a result, the radiological consequence to Korea was estimated from the accident. PC-based nuclear accident simulator, NANAS, has been developed. NANAS contains three modules: source-term estimation, atmospheric dispersion prediction and dose assessment. The source-term estimation module simulates a nuclear accident for the representative reactor types in China, Japan and Taiwan. Since the maximum calculation speed is 16 times than real time, it is possible to estimate the source-term release swiftly in case of the emergency. The atmospheric dispersion prediction module analyzes the transport and dispersion of radioactive materials in wide range including the Northeast Asia. Final results of the dose assessment module are a map projection and time chart of effective dose and thyroid dose. A hypothetical accident in Japan was simulated by NANAS. The radioactive materials were released during the first 24 hours and the source

Method for consequence calculations for severe accidents

International Nuclear Information System (INIS)

Nielsen, F.

1988-07-01

This report was commissioned by the Swedish State Power Board. The report contains a calculation of radiation doses in the surroundings caused by a theoretical core meltdown accident at Forsmark reactor No 3. The accident sequence chosen for the calculating was a release caused by total power failure. The calculations were made by means of the PLUCON4 code. Meteorological data for two years from the Forsmark meteorological tower were analysed to find representative weather situations. As typical weather, Pasquill D was chosen with a wind speed of 5 m/s, and as extreme weather, Pasquill F with a wind speed of 2 m/s. 23 tabs., 37 ills., 20 refs. (author)

Analysis of Three Mile Island Unit 2 accident

International Nuclear Information System (INIS)

Anon.

1979-01-01

NSAC is conducting a detailed review of this accident and of the lessons to be learned. So far it has concentrated primarily on events during the sixteen hours following initiation of the accident. A sequence of events has been developed and is being verified and annotated by comparing oral and written statements with instrumentation records, data logs, operator logs, and inferences which can be made from these records. This report is being developed with the expectation that, while not completed or fully verified, it may be useful at this time. Supplements may be issued later as the analyses which are still under way are completed

Credible accident analyses for TRIGA and TRIGA-fueled reactors

International Nuclear Information System (INIS)

Hawley, S.C.; Kathren, R.L.

1982-04-01

Credible accidents were developed and analyzed for TRIGA and TRIGA-fueled reactors. The only potential for offsite exposure appears to be from a fuel-handling accident that, based on highly conservative assumptions, would result in dose equivalents of less than or equal to 1 mrem to the total body from noble gases and less than or equal to 1.2 rem to the thyroid from radioiodines. Credible accidents from excess reactivity insertions, metal-water reactions, lost, misplaced, or inadvertent experiments, core rearrangements, and changes in fuel morphology and ZrH/sub x/ composition are also evaluated, and suggestions for further study provided

Uncertainties and severe-accident management

International Nuclear Information System (INIS)

Kastenberg, W.E.

1991-01-01

Severe-accident management can be defined as the use of existing and or alternative resources, systems, and actions to prevent or mitigate a core-melt accident. Together with risk management (e.g., changes in plant operation and/or addition of equipment) and emergency planning (off-site actions), accident management provides an extension of the defense-indepth safety philosophy for severe accidents. A significant number of probabilistic safety assessments have been completed, which yield the principal plant vulnerabilities, and can be categorized as (a) dominant sequences with respect to core-melt frequency, (b) dominant sequences with respect to various risk measures, (c) dominant threats that challenge safety functions, and (d) dominant threats with respect to failure of safety systems. Severe-accident management strategies can be generically classified as (a) use of alternative resources, (b) use of alternative equipment, and (c) use of alternative actions. For each sequence/threat and each combination of strategy, there may be several options available to the operator. Each strategy/option involves phenomenological and operational considerations regarding uncertainty. These include (a) uncertainty in key phenomena, (b) uncertainty in operator behavior, (c) uncertainty in system availability and behavior, and (d) uncertainty in information availability (i.e., instrumentation). This paper focuses on phenomenological uncertainties associated with severe-accident management strategies

Pegasys: software for executing and integrating analyses of biological sequences

Directory of Open Access Journals (Sweden)

Lett Drew

2004-04-01

Full Text Available Abstract Background We present Pegasys – a flexible, modular and customizable software system that facilitates the execution and data integration from heterogeneous biological sequence analysis tools. Results The Pegasys system includes numerous tools for pair-wise and multiple sequence alignment, ab initio gene prediction, RNA gene detection, masking repetitive sequences in genomic DNA as well as filters for database formatting and processing raw output from various analysis tools. We introduce a novel data structure for creating workflows of sequence analyses and a unified data model to store its results. The software allows users to dynamically create analysis workflows at run-time by manipulating a graphical user interface. All non-serial dependent analyses are executed in parallel on a compute cluster for efficiency of data generation. The uniform data model and backend relational database management system of Pegasys allow for results of heterogeneous programs included in the workflow to be integrated and exported into General Feature Format for further analyses in GFF-dependent tools, or GAME XML for import into the Apollo genome editor. The modularity of the design allows for new tools to be added to the system with little programmer overhead. The database application programming interface allows programmatic access to the data stored in the backend through SQL queries. Conclusions The Pegasys system enables biologists and bioinformaticians to create and manage sequence analysis workflows. The software is released under the Open Source GNU General Public License. All source code and documentation is available for download at http://bioinformatics.ubc.ca/pegasys/.

Using relational databases for improved sequence similarity searching and large-scale genomic analyses.

Science.gov (United States)

Mackey, Aaron J; Pearson, William R

2004-10-01

Relational databases are designed to integrate diverse types of information and manage large sets of search results, greatly simplifying genome-scale analyses. Relational databases are essential for management and analysis of large-scale sequence analyses, and can also be used to improve the statistical significance of similarity searches by focusing on subsets of sequence libraries most likely to contain homologs. This unit describes using relational databases to improve the efficiency of sequence similarity searching and to demonstrate various large-scale genomic analyses of homology-related data. This unit describes the installation and use of a simple protein sequence database, seqdb_demo, which is used as a basis for the other protocols. These include basic use of the database to generate a novel sequence library subset, how to extend and use seqdb_demo for the storage of sequence similarity search results and making use of various kinds of stored search results to address aspects of comparative genomic analysis.

Assessment of accident risks in the CRBRP. Volume 2. Appendices

Energy Technology Data Exchange (ETDEWEB)

None

1977-03-01

Appendices to Volume I include core-related accident-sequence definition, CRBRP risk-assessment sequence-probability determinations, failure-probability data, accident scenario evaluation, radioactive material release analysis, ex-core accident analysis, safety philosophy and design features, calculation of reactor accident consequences, sensitivity study, and risk from fires.

Desktop Severe Accident Graphic Simulator Module for CANDU6 : PSAIS

International Nuclear Information System (INIS)

Park, S. Y.; Song, Y. M.

2015-01-01

The ISAAC ((Integrated Severe Accident Analysis Code for CANDU Plant) code is a system level computer code capable of performing integral analyses of potential severe accident progressions in nuclear power plants, whose main purpose is to support a Level 2 probabilistic safety assessment or severe accident management strategy developments. The code has the capability to predict a severe accident progression by modeling the CANDU6- specific systems and the expected physical phenomena based on the current understanding of the unique accident progressions. The code models the sequence of accident progressions from a core heatup, pressure tube/calandria tube rupture after an uncovery from inside and outside, a relocation of the damaged fuel to the bottom of the calandria, debris behavior in the calandria, corium quenching after a debris relocation from the calandria to the calandria vault and an erosion of the calandria vault concrete floor, a hydrogen burn, and a reactor building failure. Along with the thermal hydraulics, the fission product behavior is also considered in the primary system as well as in the reactor building

Method for consequence calculations for severe accidents

International Nuclear Information System (INIS)

Nielsen, F.

1988-01-01

This report was commissioned by the Swedish State Power Board. The report contains a calculation of radiation doses in the surroundings caused by a theoretical core meltdown accident at Ringhals reactor No 3/4. The accident sequence chosen for the calcualtions was a release caused by total power failure. The calculations were made by means of the PLUCON4 code. A decontamination factor of 500 is used to account for the scrubber effect. Meteorological data for two years from the Ringhals meteorological tower were analysed to find representative weather situations. As typical weather, Pasquill D, was chosen with a wind speed of 10 m/s, and as extreme weather, Pasquill E, with a wind speed of 2 m/s. 19 refs. (author)

Characterizing the Severe Turbulence Environments Associated With Commercial Aviation Accidents. Part 1; 44 Case Study Synoptic Observational Analyses

Science.gov (United States)

Kaplan, Michael L.; Huffman, Allan W.; Lux, Kevin M.; Charney, Joseph J.; Riordan, Allan J.; Lin, Yuh-Lang; Proctor, Fred H. (Technical Monitor)

2002-01-01

A 44 case study analysis of the large-scale atmospheric structure associated with development of accident-producing aircraft turbulence is described. Categorization is a function of the accident location, altitude, time of year, time of day, and the turbulence category, which classifies disturbances. National Centers for Environmental Prediction Reanalyses data sets and satellite imagery are employed to diagnose synoptic scale predictor fields associated with the large-scale environment preceding severe turbulence. These analyses indicate a predominance of severe accident-producing turbulence within the entrance region of a jet stream at the synoptic scale. Typically, a flow curvature region is just upstream within the jet entrance region, convection is within 100 km of the accident, vertical motion is upward, absolute vorticity is low, vertical wind shear is increasing, and horizontal cold advection is substantial. The most consistent predictor is upstream flow curvature and nearby convection is the second most frequent predictor.

An Analyses of Bicycle Accidents in Ankara: Analyses of 5 Years

Directory of Open Access Journals (Sweden)

Muhittin Yilmaz

2014-12-01

Full Text Available Aim: Bicycles are used for transportation, exercise and recreation. In this study we aimed to investigate the epidemiological, clinical and economic aspects of bicycle injuries. Material and Method: We included in the study who admitted to the Emergency Department with a bicycle accident between January 2008 and July 2012. Patient age and sex, accident pattern, presence of personal protective measures, injured body part, Glasgow Coma Scale (GCS score, Revised Trauma Score (RTS, radiological findings, requested consultations, duration of hospital stay, season of injury, and average cost rates were recorded. The study population was divided into 2 age groups as 0-14 years and over 14 years. Results: A patients were 238 (81.2% male and their mean age was 31.5±14.1 years. Fifty-five (18.8% patients were female and their mean age was 34.5±15.9 years. Males had significantly higher rate of bicycle injury (p

Standardized analyses of nuclear shipping containers

International Nuclear Information System (INIS)

Parks, C.V.; Hermann, O.W.; Petrie, L.M.; Hoffman, T.J.; Tang, J.S.; Landers, N.F.; Turner, W.D.

1983-01-01

This paper describes improved capabilities for analyses of nuclear fuel shipping containers within SCALE -- a modular code system for Standardized Computer Analyses for Licensing Evaluation. Criticality analysis improvements include the new KENO V, a code which contains an enhanced geometry package and a new control module which uses KENO V and allows a criticality search on optimum pitch (maximum k-effective) to be performed. The SAS2 sequence is a new shielding analysis module which couples fuel burnup, source term generation, and radial cask shielding. The SAS5 shielding sequence allows a multidimensional Monte Carlo analysis of a shipping cask with code generated biasing of the particle histories. The thermal analysis sequence (HTAS1) provides an easy-to-use tool for evaluating a shipping cask response to the accident capability of the SCALE system to provide the cask designer or evaluator with a computational system that provides the automated procedures and easy-to-understand input that leads to standarization

Site Specific Analyses of a Spent Nuclear Fuel Transportation Accident

International Nuclear Information System (INIS)

Biwer, B. M.; Chen, S. Y.

2003-01-01

The number of spent nuclear fuel (SNF) shipments is expected to increase significantly during the time period that the United States' inventory of SNF is sent to a final disposal site. Prior work estimated that the highest accident risks of a SNF shipping campaign to the proposed geologic repository at Yucca Mountain were in the corridor states, such as Illinois. The largest potential human health impacts would be expected to occur in areas with high population densities such as urban settings. Thus, our current study examined the human health impacts from the most plausible severe SNF transportation accidents in the Chicago metropolitan area. The RISKIND 2.0 program was used to model site-specific data for an area where the largest impacts might occur. The results have shown that the radiological human health consequences of a severe SNF rail transportation accident on average might be similar to one year of exposure to natural background radiation for those persons living a nd working in the most affected areas downwind of the actual accident location. For maximally exposed individuals, an exposure similar to about two years of exposure to natural background radiation was estimated. In addition to the accident probabilities being very low (approximately 1 chance in 10,000 or less during the entire shipping campaign), the actual human health impacts are expected to be lower if any of the accidents considered did occur, because the results are dependent on the specific location and weather conditions, such as wind speed and direction, that were selected to maximize the results. Also, comparison of the results of longer duration accident scenarios against U.S. Environmental Protection Agency guidelines was made to demonstrate the usefulness of this site-specific analysis for emergency planning purposes

Phylogenetic study on Shiraia bambusicola by rDNA sequence analyses.

Science.gov (United States)

Cheng, Tian-Fan; Jia, Xiao-Ming; Ma, Xiao-Hang; Lin, Hai-Ping; Zhao, Yu-Hua

2004-01-01

In this study, 18S rDNA and ITS-5.8S rDNA regions of four Shiraia bambusicola isolates collected from different species of bamboos were amplified by PCR with universal primer pairs NS1/NS8 and ITS5/ITS4, respectively, and sequenced. Phylogenetic analyses were conducted on three selected datasets of rDNA sequences. Maximum parsimony, distance and maximum likelihood criteria were used to infer trees. Morphological characteristics were also observed. The positioning of Shiraia in the order Pleosporales was well supported by bootstrap, which agreed with the placement by Amano (1980) according to their morphology. We did not find significant inter-hostal differences among these four isolates from different species of bamboos. From the results of analyses and comparison of their rDNA sequences, we conclude that Shiraia should be classified into Pleosporales as Amano (1980) proposed and suggest that it might be positioned in the family Phaeosphaeriaceae. Copyright 2004 WILEY-VCH Verlag GmbH & Co.

Process hazards analysis (PrHA) program, bridging accident analyses and operational safety

International Nuclear Information System (INIS)

Richardson, J.A.; McKernan, S.A.; Vigil, M.J.

2003-01-01

Recently the Final Safety Analysis Report (FSAR) for the Plutonium Facility at Los Alamos National Laboratory, Technical Area 55 (TA-55) was revised and submitted to the US. Department of Energy (DOE). As a part of this effort, over seventy Process Hazards Analyses (PrHAs) were written and/or revised over the six years prior to the FSAR revision. TA-55 is a research, development, and production nuclear facility that primarily supports US. defense and space programs. Nuclear fuels and material research; material recovery, refining and analyses; and the casting, machining and fabrication of plutonium components are some of the activities conducted at TA-35. These operations involve a wide variety of industrial, chemical and nuclear hazards. Operational personnel along with safety analysts work as a team to prepare the PrHA. PrHAs describe the process; identi fy the hazards; and analyze hazards including determining hazard scenarios, their likelihood, and consequences. In addition, the interaction of the process to facility systems, structures and operational specific protective features are part of the PrHA. This information is rolled-up to determine bounding accidents and mitigating systems and structures. Further detailed accident analysis is performed for the bounding accidents and included in the FSAR. The FSAR is part of the Documented Safety Analysis (DSA) that defines the safety envelope for all facility operations in order to protect the worker, the public, and the environment. The DSA is in compliance with the US. Code of Federal Regulations, 10 CFR 830, Nuclear Safety Management and is approved by DOE. The DSA sets forth the bounding conditions necessary for the safe operation for the facility and is essentially a 'license to operate.' Safely of day-to-day operations is based on Hazard Control Plans (HCPs). Hazards are initially identified in the PrI-IA for the specific operation and act as input to the HCP. Specific protective features important to worker

Treatment of Events Representing System Success in Accident Sequences in PSA Models with ET/FT Linking

International Nuclear Information System (INIS)

Vrbanic, I.; Spiler, J.; Mikulicic, V.; Simic, Z.

2002-01-01

Treatment of events that represent systems' successes in accident sequences is well known issue associated primarily with those PSA models that employ event tree / fault tree (ET / FT) linking technique. Even theoretically clear, practical implementation and usage creates for certain PSA models a number of difficulties regarding result correctness. Strict treatment of success-events would require consistent applying of de Morgan laws. However, there are several problems related to it. First, Boolean resolution of the overall model, such as the one representing occurrence of reactor core damage, becomes very challenging task if De Morgan rules are applied consistently at all levels. Even PSA tools of the newest generation have some problems with performing such a task in a reasonable time frame. The second potential issue is related to the presence of negated basic events in minimal cutsets. If all the basic events that result from strict applying of De Morgan rules are retained in presentation of minimal cutsets, their readability and interpretability may be impaired severely. It is also worth noting that the concept of a minimal cutset is tied to equipment failures, rather than to successes. For reasons like these, various simplifications are employed in PSA models and tools, when it comes to the treatment of success-events in the sequences. This paper provides a discussion of major concerns associated with the treatment of success-events in accident sequences of a typical PSA model. (author)

Validation and application of the system code ATHLET-CD for BWR severe accident analyses

Energy Technology Data Exchange (ETDEWEB)

Di Marcello, Valentino, E-mail: valentino.marcello@kit.edu; Imke, Uwe; Sanchez, Victor

2016-10-15

Highlights: • We present the application of the system code ATHLET-CD code for BWR safety analyses. • Validation of core in-vessel models is performed based on KIT CORA experiments. • A SB-LOCA scenario is simulated on a generic German BWR plant up to vessel failure. • Different core reflooding possibilities are investigated to mitigate the accident consequences. • ATHLET-CD modelling features reflect the current state of the art of severe accident codes. - Abstract: This paper is aimed at the validation and application of the system code ATHLET-CD for the simulation of severe accident phenomena in Boiling Water Reactors (BWR). The corresponding models for core degradation behaviour e.g., oxidation, melting and relocation of core structural components are validated against experimental data available from the CORA-16 and -17 bundle tests. Model weaknesses are discussed along with needs for further code improvements. With the validated ATHLET-CD code, calculations are performed to assess the code capabilities for the prediction of in-vessel late phase core behaviour and reflooding of damaged fuel rods. For this purpose, a small break LOCA scenario for a generic German BWR with postulated multiple failures of the safety systems was selected. In the analysis, accident management measures represented by cold water injection into the damaged reactor core are addressed to investigate the efficacy in avoiding or delaying the failure of the reactor pressure vessel. Results show that ATHLET-CD is applicable to the description of BWR plant behaviour with reliable physical models and numerical methods adopted for the description of key in-vessel phenomena.

Application of forensic image analysis in accident investigations.

Science.gov (United States)

Verolme, Ellen; Mieremet, Arjan

2017-09-01

Forensic investigations are primarily meant to obtain objective answers that can be used for criminal prosecution. Accident analyses are usually performed to learn from incidents and to prevent similar events from occurring in the future. Although the primary goal may be different, the steps in which information is gathered, interpreted and weighed are similar in both types of investigations, implying that forensic techniques can be of use in accident investigations as well. The use in accident investigations usually means that more information can be obtained from the available information than when used in criminal investigations, since the latter require a higher evidence level. In this paper, we demonstrate the applicability of forensic techniques for accident investigations by presenting a number of cases from one specific field of expertise: image analysis. With the rapid spread of digital devices and new media, a wealth of image material and other digital information has become available for accident investigators. We show that much information can be distilled from footage by using forensic image analysis techniques. These applications show that image analysis provides information that is crucial for obtaining the sequence of events and the two- and three-dimensional geometry of an accident. Since accident investigation focuses primarily on learning from accidents and prevention of future accidents, and less on the blame that is crucial for criminal investigations, the field of application of these forensic tools may be broader than would be the case in purely legal sense. This is an important notion for future accident investigations. Copyright © 2017 Elsevier B.V. All rights reserved.

On high-temperature reactor accident topology

International Nuclear Information System (INIS)

Fassbender, J.; Kroeger, W.; Wolters, J.

1981-01-01

American and German risk studies for an HTGR and independent investigations of hypothetical accident sequences led to a fundamental understanding of the topology of HTGR accident sequences. The dominating importance of core heat-up accidents was confirmed and the initiating events were identified. Complications of core heat-up accidents by air or water ingress are of minor importance for the risk, whereas the long-term development of accidents during days and weeks plays an important role for the environmental impact. The risk caused by an HTGR at a German site cannot yet be determined exactly, because no modern German HTGR design has passed a licensing procedure. Cautious estimates show that risk will appear to be substantially smaller than the LWR risk. The main reasons are the considerably reduced release of fission procucts and the slow development of core heat-up accidents leaving much time for measures which reduce the risk. (orig.) [de

Safety related studies on the accident behaviour of the HTR-100

International Nuclear Information System (INIS)

Wolters, J.; Mertens, J.; Altes, J.; Bongartz, R.; Breitbach, G.; David, P.H.; Degen, G.; Ehrlich, H.G.; Escherich, K.H.; Frank, E.; Hennings, W.; Jahn, W.; Koschmieder, R.; Marx, J.; Meister, G.; Moormann, R.; Rehm, W.; Verfondern, K.

1991-10-01

The aim of investigations was to verify the safety concept of the plant for balance and to quantify the radiological risk to be expected in operating an HTR-100 double unit system. Moreover, aspects of the investment risk were considered. The spectrum of initiating events ranged from so-called transients to leaks in the primary circuit and steam generator and even included earthquakes. Some of the event trees derived were highly complex and extensive due to the situation of the steam generator above the core and with regard to the double unit plant concept with increased possibilities of accident control, but also with respect to potential accident propagation. Correspondingly sophisticated analyses were required to identify risk-relevant event sequences. Environmental exposure for all risk-relevant accidents is so low that accident consequence calculations do not reveal any lethal radiation doses and practically no stochastic fatal injuries. These calculations neither assumed acute protective measures nor long-term resettlement or decontamination. The radiological risk caused by an HTR-100 plant is therefore to be classified as very low. The initiating events selected as representative and the event sequences studied in detail cover the risk-relevant event spectrum well into the hypothetical range. (orig./HP) [de

Analysis of molten fuel behavior in coolant channel during severe accidents in KALIMER

International Nuclear Information System (INIS)

Suk, Soo Dong; Lee, Yong Bum; Hahn, Do Hee

2004-11-01

Preliminary safety analyses of the KALIMER-600 design have shown that the design has inherent safety characteristics and is capable of accommodating double fault initiators such as ATWS events without boiling coolant or melting fuel. For the future design of liquid metal reactor, however, the evaluation of the safety performance and the determination of containment requirements may require consideration of tripe-fault accident sequences of extremely low probability of occurrence that leads to fuel melting. For any postulated accident sequence which leads to core melting, in-vessel retention of the core debris will required as a design requirement for the future design of LMR. For sodium-cooled core designs with metallic fuel, one of the major phenomenological modeling uncertainties to be resolved is the potential for freezing and plugging of molten metallic fuel in above- and below-core structures and possibly in inter-subassembly spaces. In this study, scoping analyses were carried out to evaluate the penetration depths in the coolant channels by molten fuel mixture during the unprotected loss-of-flow accidents in the core of the KALIMER-600. It is assumed in the analyses that a solid fuel crust would start to form upon contact with the coolant channel structure temperature of which is below the fuel solidus. The analysis results predict that the coolant channels would be plugged by the freezing molten fuel in the inlet lower shield as well as in the outlet, fission-gas-plenum region for the KALIMER-600 design

Current status of low power/shutdown PSA and accident sequence analysis for loss of RHR during mid-loop operation

International Nuclear Information System (INIS)

Park, Chang Kyu; Choi, Young; Kim, Tae Woon; Jin, Young Ho

1994-07-01

Probabilistic safety assessment (PSA) has been applied to only full-power operation of nuclear power plant (NPP), but some events which were recently occurred could reach severe plant damage state. Thus, various countries around the world have focused their interests on the evaluation for low power/shutdown (LP/S) operation. This report covers the main stream of LP/S PSA methodology, current status of LP/S PSA practices and results, and accident sequence analysis for loss of RHR during mid-loop operation. Therefore this report would be helpful for us to practice LP/S PSA for YGN 5,6 NPP which will be built in the near future. Also the results of accident sequence analysis show that operator's mis-diagnosis and failure of recovery action would initiate core damage during LP/S operation. In summary, overall environmental improvements (equipments, procedures, Tech Spec, etc, ...) and operating support system will be very useful to reduce risk during LP/S operation. (Author) 5 figs., 9 tabs

Fuel relocation modeling in the SAS4A accident analysis code system

International Nuclear Information System (INIS)

Tentner, A.M.; Miles, K.J.

1985-01-01

SAS4A is a new code system which has been designed for analyzing the initial phase of Hypothetical Core Disruptive Accidents (HCDAs) up to gross melting or failure of the subassembly walls. During such postulated accident scenarios as the Loss-of-Flow (LOF) and Transient-Overpower (TOP) events, the relocation of the fuel plays a key role in determining the sequence of events and the amount of energy produced before neutronic shutdown. This paper discusses the general strategy used in modeling the various phenomena which lead to fuel relocation and presents the key fuel relocation models used in SAS4A. The implications of these models for the whole-core accident analysis as well as recent results of fuel motion experiment analyses are also presented

Simulation with the MELCOR code of two severe accident sequences, Station Blackout and Small Break LOCA, for the Atucha I nuclear power plant

International Nuclear Information System (INIS)

Valle Cepero, Reinaldo

2004-01-01

The results of the PSA-I applied to the Atucha I nuclear power plant (CNA I) determine the accidental sequences with the most influence related to the probability of the core reactor damage. Among those sequences are include, the Station Blackout and lost of primary coolant, combine with the failure of the emergency injection systems by pipe breaks of diameters between DN100 - DN25 or equivalent areas, Small LOCA. This paper has the objective to model and analyze the behavior of the primary circuit and the pressure vessel during the evolution of those two accidental sequences. It presented a detailed analysis of the main phenomena that occur from the initial moment of the accident to the failure moment of the pressure vessel and the melt material fall to the reactor cavity. Two sequences were taken into account, considering the main phenomena (core uncover, heating, fuel element oxidation, hydrogen generation, degradation and relocation of the melt material, failure of the support structures, etc.) and the time of occurrence, of those events will be different, if it is considered that both sequences will be developed in different scenarios. One case is an accident with the primary circuit to a high pressure (Station Blackout scenario) and the other with a early primary circuit depressurization due to the lost of primary coolant. For this work the MELCOR 1.8.5 code was used and it allows within a unified framework to modeling an extensive spectrum of phenomenology associated with the severe accidents. (author)

Cloud-based bioinformatics workflow platform for large-scale next-generation sequencing analyses.

Science.gov (United States)

Liu, Bo; Madduri, Ravi K; Sotomayor, Borja; Chard, Kyle; Lacinski, Lukasz; Dave, Utpal J; Li, Jianqiang; Liu, Chunchen; Foster, Ian T

2014-06-01

Due to the upcoming data deluge of genome data, the need for storing and processing large-scale genome data, easy access to biomedical analyses tools, efficient data sharing and retrieval has presented significant challenges. The variability in data volume results in variable computing and storage requirements, therefore biomedical researchers are pursuing more reliable, dynamic and convenient methods for conducting sequencing analyses. This paper proposes a Cloud-based bioinformatics workflow platform for large-scale next-generation sequencing analyses, which enables reliable and highly scalable execution of sequencing analyses workflows in a fully automated manner. Our platform extends the existing Galaxy workflow system by adding data management capabilities for transferring large quantities of data efficiently and reliably (via Globus Transfer), domain-specific analyses tools preconfigured for immediate use by researchers (via user-specific tools integration), automatic deployment on Cloud for on-demand resource allocation and pay-as-you-go pricing (via Globus Provision), a Cloud provisioning tool for auto-scaling (via HTCondor scheduler), and the support for validating the correctness of workflows (via semantic verification tools). Two bioinformatics workflow use cases as well as performance evaluation are presented to validate the feasibility of the proposed approach. Copyright © 2014 Elsevier Inc. All rights reserved.

Sequencing, Characterization, and Comparative Analyses of the Plastome of Caragana rosea var. rosea

Directory of Open Access Journals (Sweden)

Mei Jiang

2018-05-01

Full Text Available To exploit the drought-resistant Caragana species, we performed a comparative study of the plastomes from four species: Caragana rosea, C. microphylla, C. kozlowii, and C. Korshinskii. The complete plastome sequence of the C. rosea was obtained using the next generation DNA sequencing technology. The genome is a circular structure of 133,122 bases and it lacks inverted repeat. It contains 111 unique genes, including 76 protein-coding, 30 tRNA, and four rRNA genes. Repeat analyses obtained 239, 244, 258, and 246 simple sequence repeats in C. rosea, C. microphylla, C. kozlowii, and C. korshinskii, respectively. Analyses of sequence divergence found two intergenic regions: trnI-CAU-ycf2 and trnN-GUU-ycf1, exhibiting a high degree of variations. Phylogenetic analyses showed that the four Caragana species belong to a monophyletic clade. Analyses of Ka/Ks ratios revealed that five genes: rpl16, rpl20, rps11, rps7, and ycf1 and several sites having undergone strong positive selection in the Caragana branch. The results lay the foundation for the development of molecular markers and the understanding of the evolutionary process for drought-resistant characteristics.

Application of dynamic probabilistic safety assessment approach for accident sequence precursor analysis: Case study for steam generator tube rupture

Energy Technology Data Exchange (ETDEWEB)

Lee, Han Sul; Heo, Gyun Young [Kyung Hee University, Yongin (Korea, Republic of); Kim, Tae Wan [Incheon National University, Incheon (Korea, Republic of)

2017-03-15

The purpose of this research is to introduce the technical standard of accident sequence precursor (ASP) analysis, and to propose a case study using the dynamic-probabilistic safety assessment (D-PSA) approach. The D-PSA approach can aid in the determination of high-risk/low-frequency accident scenarios from all potential scenarios. It can also be used to investigate the dynamic interaction between the physical state and the actions of the operator in an accident situation for risk quantification. This approach lends significant potential for safety analysis. Furthermore, the D-PSA approach provides a more realistic risk assessment by minimizing assumptions used in the conventional PSA model so-called the static-PSA model, which are relatively static in comparison. We performed risk quantification of a steam generator tube rupture (SGTR) accident using the dynamic event tree (DET) methodology, which is the most widely used methodology in D-PSA. The risk quantification results of D-PSA and S-PSA are compared and evaluated. Suggestions and recommendations for using D-PSA are described in order to provide a technical perspective.

Analysis of radionuclide behavior in a BWR Mark-II containment under severe accident management condition in low pressure sequence

International Nuclear Information System (INIS)

Funayama, Kyoko; Kajimoto, Mitsuhiro; Nagayoshi, Takuji; Tanaka, Nobuo

1999-01-01

In the Level 2 PSA program at INS/NUPEC, MELCOR1.8.3 is extensively applied to analyze radionuclide behavior of dominant sequences. In addition, the revised source terms provided in the NUREG-1465 report have been also discussed to examine the potential of the radionuclides release to the environment in the conventional siting criteria. In the present study, characteristics of source terms to the environment were examined comparing with results by the Hypothetical Accident (LOCA), NUREG-1465 and MELCOR1.8.3. calculation for a typical BWR with a Mark-II containment in order to assure conservatives of the Hypothetical Accident in Japan. Release fractions of iodine to the environment for the Hypothetical Accident and NUREG-1465, which used engineering models for predicting radionuclide behaviors, were about 10 -4 and 10 -6 of core inventory, respectively, while the best estimate MELCOR1.8.3 code predicted 10 -9 of iodine to the environment. The present study showed that the engineering models in the Hypothetical Accident or NUREG-1465 have large conservatives to estimate source term of iodine to the environment. (author)

Application of dynamic probabilistic safety assessment approach for accident sequence precursor analysis: Case study for steam generator tube rupture

International Nuclear Information System (INIS)

Lee, Han Sul; Heo, Gyun Young; Kim, Tae Wan

2017-01-01

The purpose of this research is to introduce the technical standard of accident sequence precursor (ASP) analysis, and to propose a case study using the dynamic-probabilistic safety assessment (D-PSA) approach. The D-PSA approach can aid in the determination of high-risk/low-frequency accident scenarios from all potential scenarios. It can also be used to investigate the dynamic interaction between the physical state and the actions of the operator in an accident situation for risk quantification. This approach lends significant potential for safety analysis. Furthermore, the D-PSA approach provides a more realistic risk assessment by minimizing assumptions used in the conventional PSA model so-called the static-PSA model, which are relatively static in comparison. We performed risk quantification of a steam generator tube rupture (SGTR) accident using the dynamic event tree (DET) methodology, which is the most widely used methodology in D-PSA. The risk quantification results of D-PSA and S-PSA are compared and evaluated. Suggestions and recommendations for using D-PSA are described in order to provide a technical perspective

A Quantitative Accident Sequence Analysis for a VHTR

Energy Technology Data Exchange (ETDEWEB)

Kim, Jintae; Lee, Joeun; Jae, Moosung [Hanyang University, Seoul (Korea, Republic of)

2016-05-15

In Korea, the basic design features of VHTR are currently discussed in the various design concepts. Probabilistic risk assessment (PRA) offers a logical and structured method to assess risks of a large and complex engineered system, such as a nuclear power plant. It will be introduced at an early stage in the design, and will be upgraded at various design and licensing stages as the design matures and the design details are defined. Risk insights to be developed from the PRA are viewed as essential to developing a design that is optimized in meeting safety objectives and in interpreting the applicability of the existing demands to the safety design approach of the VHTR. In this study, initiating events which may occur in VHTRs were selected through MLD method. The initiating events were then grouped into four categories for the accident sequence analysis. Initiating events frequency and safety systems failure rate were calculated by using reliability data obtained from the available sources and fault tree analysis. After quantification, uncertainty analysis was conducted. The SR and LR frequency are calculated respectively 7.52E- 10/RY and 7.91E-16/RY, which are relatively less than the core damage frequency of LWRs.

Application of a Software tool for Evaluating Human Factors in Accident Sequences

International Nuclear Information System (INIS)

Queral, Cesar; Exposito, Antonio; Gonzalez, Isaac; Quiroga, Juan Antonio; Ibarra, Aitor; Hortal, Javier; Hulsund, John-Einar; Nilsen, Svein

2006-01-01

The Probabilistic Safety Assessment (PSA) includes the actions of the operator like elements in the set of the considered protection performances during accident sequences. Nevertheless, its impact throughout a sequence is not analyzed in a dynamic way. In this sense, it is convenient to make more detailed studies about its importance in the dynamics of the sequences, letting make studies of sensitivity respect to the human reliability and the response times. For this reason, the CSN is involved in several activities oriented to develop a new safety analysis methodology, the Integrated Safety Assessment (ISA), which must be able to incorporate operator actions in conventional thermo-hydraulic (TH) simulations. One of them is the collaboration project between CSN, HRP and the DSE-UPM that started in 2003. In the framework of this project, a software tool has been developed to incorporate operator actions in TH simulations. As a part of the ISA, this tool permits to quantify human error probabilities (HEP) and to evaluate its impact in the final state of the plant. Independently, it can be used for evaluating the impact of the execution by operators of procedures and guidelines in the final state of the plant and the evaluation of the allowable response times for the manual actions of the operator. The results obtained in the first pilot case are included in this paper. (authors)

State of Level 2 analyses and severe accident management in Spanish nuclear power plants

International Nuclear Information System (INIS)

Otero, R.

1998-01-01

The state of the PSA/IPE studies in the Spanish NPPs is presented in this report, as well as the plans to implement the severe accident management strategy both in the Spanish BWRs and PWRs. First, the Spanish LWRs are introduced, and the scope of the IPE analyses required by the Spanish Regulatory Commission (CSN) is given. The general overview is completed with the current degree of development for the IPE studies in each plant. In the second part the methods and tools are shown which are used by the Spanish plants to develop their Level 2 analysis. The different strategies for severe accident management adopted by the BWPs and PWRs in Spain are also outlined. The sources and implementation of the Severe Accident Guidelines (SAG) are described. More detail is given in the following chapters to the containment analysis of Trillo (PWR, KWU design) and Cofrentes (BWR/6, GE design) NPPs, whose development is being carried out by IBERDROLA. The analysis which has been performed up to date for Trillo is limited to the Plant Damage State (PDS) definition. However, the main phenomena challenging its containment performance have been identified, and they are summarized here. The Level 2 analysis for Cofrentes is comparatively more developed. The main phenomena and the key equipment affecting its containment behaviour are presented. Finally the conclusions of this report are elaborated. (author)

Key Characteristics of Combined Accident including TLOFW accident for PSA Modeling

Energy Technology Data Exchange (ETDEWEB)

Kim, Bo Gyung; Kang, Hyun Gook [KAIST, Daejeon (Korea, Republic of); Yoon, Ho Joon [Khalifa University of Science, Technology and Research, Abu Dhabi (United Arab Emirates)

2015-05-15

The conventional PSA techniques cannot adequately evaluate all events. The conventional PSA models usually focus on single internal events such as DBAs, the external hazards such as fire, seismic. However, the Fukushima accident of Japan in 2011 reveals that very rare event is necessary to be considered in the PSA model to prevent the radioactive release to environment caused by poor treatment based on lack of the information, and to improve the emergency operation procedure. Especially, the results from PSA can be used to decision making for regulators. Moreover, designers can consider the weakness of plant safety based on the quantified results and understand accident sequence based on human actions and system availability. This study is for PSA modeling of combined accidents including total loss of feedwater (TLOFW) accident. The TLOFW accident is a representative accident involving the failure of cooling through secondary side. If the amount of heat transfer is not enough due to the failure of secondary side, the heat will be accumulated to the primary side by continuous core decay heat. Transients with loss of feedwater include total loss of feedwater accident, loss of condenser vacuum accident, and closure of all MSIVs. When residual heat removal by the secondary side is terminated, the safety injection into the RCS with direct primary depressurization would provide alternative heat removal. This operation is called feed and bleed (F and B) operation. Combined accidents including TLOFW accident are very rare event and partially considered in conventional PSA model. Since the necessity of F and B operation is related to plant conditions, the PSA modeling for combined accidents including TLOFW accident is necessary to identify the design and operational vulnerabilities.The PSA is significant to assess the risk of NPPs, and to identify the design and operational vulnerabilities. Even though the combined accident is very rare event, the consequence of combined

Probabilistic accident sequence recovery analysis

International Nuclear Information System (INIS)

Stutzke, Martin A.; Cooper, Susan E.

2004-01-01

Recovery analysis is a method that considers alternative strategies for preventing accidents in nuclear power plants during probabilistic risk assessment (PRA). Consideration of possible recovery actions in PRAs has been controversial, and there seems to be a widely held belief among PRA practitioners, utility staff, plant operators, and regulators that the results of recovery analysis should be skeptically viewed. This paper provides a framework for discussing recovery strategies, thus lending credibility to the process and enhancing regulatory acceptance of PRA results and conclusions. (author)

Use of PSA to support accident management at NPPs

International Nuclear Information System (INIS)

Gomez Cobo, A.

1997-01-01

The presentation discusses the following: Overview of PSA level 2; Introduction: Framework; Accident Progression Phenomena in the Confinement/containment; Severe Accident Sequences; Examples; Results and Insights. Accident Management: Concepts; Process; Use of PSA to support Accident; Management

On the sequence and consequences of the Chernobyl reactor accident

Energy Technology Data Exchange (ETDEWEB)

Hennies, H H

1986-01-01

A serious reactor accident occurred on April 26, 1986 at Chernobyl near Kiev (Soviet Union) where, after melting of the core, there was a considerable release of radioactivity to the environment and to the atmosphere. The radioactivity release caused irradiation of the operating staff, which led to 24 deaths by June 1986. Hardly anything is known about the irradiation of the environment of the reactor plant, but the population within a radius of 30 km was evacuated. The radioactivity released into the atmosphere spread all over Europe, and Germany was affected a few days after the accident. The article gives a short description of the plant which suffered the accident, one tries to describe the course of the accident and to discuss the applicability to German plants.

Application of MELCOR Code to a French PWR 900 MWe Severe Accident Sequence and Evaluation of Models Performance Focusing on In-Vessel Thermal Hydraulic Results

International Nuclear Information System (INIS)

De Rosa, Felice

2006-01-01

In the ambit of the Severe Accident Network of Excellence Project (SARNET), funded by the European Union, 6. FISA (Fission Safety) Programme, one of the main tasks is the development and validation of the European Accident Source Term Evaluation Code (ASTEC Code). One of the reference codes used to compare ASTEC results, coming from experimental and Reactor Plant applications, is MELCOR. ENEA is a SARNET member and also an ASTEC and MELCOR user. During the first 18 months of this project, we performed a series of MELCOR and ASTEC calculations referring to a French PWR 900 MWe and to the accident sequence of 'Loss of Steam Generator (SG) Feedwater' (known as H2 sequence in the French classification). H2 is an accident sequence substantially equivalent to a Station Blackout scenario, like a TMLB accident, with the only difference that in H2 sequence the scram is forced to occur with a delay of 28 seconds. The main events during the accident sequence are a loss of normal and auxiliary SG feedwater (0 s), followed by a scram when the water level in SG is equal or less than 0.7 m (after 28 seconds). There is also a main coolant pumps trip when ΔTsat < 10 deg. C, a total opening of the three relief valves when Tric (core maximal outlet temperature) is above 603 K (330 deg. C) and accumulators isolation when primary pressure goes below 1.5 MPa (15 bar). Among many other points, it is worth noting that this was the first time that a MELCOR 1.8.5 input deck was available for a French PWR 900. The main ENEA effort in this period was devoted to prepare the MELCOR input deck using the code version v.1.8.5 (build QZ Oct 2000 with the latest patch 185003 Oct 2001). The input deck, completely new, was prepared taking into account structure, data and same conditions as those found inside ASTEC input decks. The main goal of the work presented in this paper is to put in evidence where and when MELCOR provides good enough results and why, in some cases mainly referring to its

Evaluation of severe accident risks: Methodology for the containment, source term, consequence, and risk integration analyses. Volume 1, Revision 1

International Nuclear Information System (INIS)

Gorham, E.D.; Breeding, R.J.; Brown, T.D.; Harper, F.T.; Helton, J.C.; Murfin, W.B.; Hora, S.C.

1993-12-01

NUREG-1150 examines the risk to the public from five nuclear power plants. The NUREG-1150 plant studies are Level III probabilistic risk assessments (PRAs) and, as such, they consist of four analysis components: accident frequency analysis, accident progression analysis, source term analysis, and consequence analysis. This volume summarizes the methods utilized in performing the last three components and the assembly of these analyses into an overall risk assessment. The NUREG-1150 analysis approach is based on the following ideas: (1) general and relatively fast-running models for the individual analysis components, (2) well-defined interfaces between the individual analysis components, (3) use of Monte Carlo techniques together with an efficient sampling procedure to propagate uncertainties, (4) use of expert panels to develop distributions for important phenomenological issues, and (5) automation of the overall analysis. Many features of the new analysis procedures were adopted to facilitate a comprehensive treatment of uncertainty in the complete risk analysis. Uncertainties in the accident frequency, accident progression and source term analyses were included in the overall uncertainty assessment. The uncertainties in the consequence analysis were not included in this assessment. A large effort was devoted to the development of procedures for obtaining expert opinion and the execution of these procedures to quantify parameters and phenomena for which there is large uncertainty and divergent opinions in the reactor safety community

Phenomenological analyses and their application to the Defense Waste Processing Facility probabilistic safety analysis accident progression event tree. Revision 1

International Nuclear Information System (INIS)

Kalinich, D.A.; Thomas, J.K.; Gough, S.T.; Bailey, R.T.; Kearnaghan, D.P.

1995-01-01

In the Defense Waste Processing Facility (DWPF) Safety Analysis Reports (SARs) for the Savannah River Site (SRS), risk-based perspectives have been included per US Department of Energy (DOE) Order 5480.23. The NUREG-1150 Level 2/3 Probabilistic Risk Assessment (PRA) methodology was selected as the basis for calculating facility risk. The backbone of this methodology is the generation of an Accident Progression Event Tree (APET), which is solved using the EVNTRE computer code. To support the development of the DWPF APET, deterministic modeling of accident phenomena was necessary. From these analyses, (1) accident progressions were identified for inclusion into the APET; (2) branch point probabilities and any attendant parameters were quantified; and (3) the radionuclide releases to the environment from accidents were determined. The phenomena of interest for accident progressions included explosions, fires, a molten glass spill, and the response of the facility confinement system during such challenges. A variety of methodologies, from hand calculations to large system-model codes, were used in the evaluation of these phenomena

A Preliminary Neutral Framework for the Accident Sequence Evaluation for a Hydrogen Conversion Reactor

International Nuclear Information System (INIS)

Han, Seok Jung; Yang, Joon Eon

2005-01-01

A framework for an early stage PSA for a hydrogen conversion reactor has been proposed in this paper. The approach is based on a functional and top-down approach. A main concerning point of this approach is to use a design neutral framework. A design neutral framework of PSA can provide a flexibility to apply to several candidate design concepts or options. This neutral-framework idea was borrowed from a proposed regulatory framework in US NRC. The feasibility of our proposed approach has been assessed to be applied in an accident sequence analysis for a hydrogen conversion reactor

msgbsR: An R package for analysing methylation-sensitive restriction enzyme sequencing data.

Science.gov (United States)

Mayne, Benjamin T; Leemaqz, Shalem Y; Buckberry, Sam; Rodriguez Lopez, Carlos M; Roberts, Claire T; Bianco-Miotto, Tina; Breen, James

2018-02-01

Genotyping-by-sequencing (GBS) or restriction-site associated DNA marker sequencing (RAD-seq) is a practical and cost-effective method for analysing large genomes from high diversity species. This method of sequencing, coupled with methylation-sensitive enzymes (often referred to as methylation-sensitive restriction enzyme sequencing or MRE-seq), is an effective tool to study DNA methylation in parts of the genome that are inaccessible in other sequencing techniques or are not annotated in microarray technologies. Current software tools do not fulfil all methylation-sensitive restriction sequencing assays for determining differences in DNA methylation between samples. To fill this computational need, we present msgbsR, an R package that contains tools for the analysis of methylation-sensitive restriction enzyme sequencing experiments. msgbsR can be used to identify and quantify read counts at methylated sites directly from alignment files (BAM files) and enables verification of restriction enzyme cut sites with the correct recognition sequence of the individual enzyme. In addition, msgbsR assesses DNA methylation based on read coverage, similar to RNA sequencing experiments, rather than methylation proportion and is a useful tool in analysing differential methylation on large populations. The package is fully documented and available freely online as a Bioconductor package ( https://bioconductor.org/packages/release/bioc/html/msgbsR.html ).

The role of internal and external control for mitigating or preventing LMR accidents

International Nuclear Information System (INIS)

Waltar, A.E.; Padilla, A.; Seeman, S.E.

1987-01-01

For the safety assessment of LMFBRs, much effort has been devoted to the analyses of LOF accident sequences with an emphasis on initiating-phase (IP) energetics (LOF-d-TOP event). Important knowledge and experiences on the IP energetics have been accumulated through reactor studies and in-pile experiment analyses, typically for the CABRI experiments. The present paper summarises the current understanding of key phenomenology relevant to the IP energetics based on the CABRI experiment analyses and the validation study for the PAPAS-2S, SAS3D and SAS4A codes. (author)

Validation of severe accident management guidance for the wolsong plants

International Nuclear Information System (INIS)

Park, S. Y.; Jin, Y. H.; Kim, S. D.; Song, Y. M.

2006-01-01

Full text: Full text: The severe accident management(SAM) guidance has been developed for the Wolsong nuclear power plants in Korea. The Wolsong plants are 700MWe CANDU-type reactors with heavy water as the primary coolant, natural uranium-fueled pressurized, horizontal tubes, surrounded by heavy water moderator inside a horizontal calandria vessel. The guidance includes six individual accident management strategies: (1) injection into primary heat transport system (2) injection into calandria vessel (3) injection into calandria vault (4) reduction of fission product release (5) control of reactor building condition (6) reduction of reactor building hydrogen. The paper provides the approaches to validate the SAM guidance. The validation includes the evaluation of:(l) effectiveness of accident management strategies, (2) performance of mitigation systems or components, (3) calculation aids, (4) strategy control diagram, and (5) interface with emergency operation procedure and with radiation emergency plan. Several severe accident sequences with high probability is selected from the plant specific level 2 probabilistic safety analysis results for the validation of SAM guidance. Afterward, thermal hydraulic and severe accident phenomenological analyses is performed using ISAAC(Integrated Severe Accident Analysis Code for CANDU Plant) computer program. Furthermore, the experiences obtained from a table-top-drill is also discussed

JERICHO computer code: PWR containment response during severe accidents description and sensitivity analysis

International Nuclear Information System (INIS)

Fermandjian, J.; Evrard, J.M.

1983-12-01

The JERICHO code has been developed in order to study the thermodynamic behaviour inside the reactor containment building for the complete spectrum of accident sequences likely to occur in such a reactor, including models for the various mass and energy transfer phenomena, for water spray, for hydrogen and carbon monoxide flammability limits and combustion, as well as for containment venting. Sensitivity analyses have been performed on a severe accident sequence, (namely, small LOCA with failure of the emergency core cooling and containment spray systems), involving core melting and subsequent concrete containment basemat erosion. The effect of various models, such as mass and energy transfer to the structures, has been studied. The influence of the concrete composition, of the fission product deposition and of the thermal degradation of the reactor cavity concrete walls on long term thermodynamic behaviour has also been investigated

Iodine chemistry effect on source term assessments. A MELCOR 186 YT study of a PWR severe accident sequence

International Nuclear Information System (INIS)

Herranz, Luis E.; Garcia, Monica; Otero, Bernadette

2009-01-01

Level-2 Probabilistic Safety Analysis has demonstrated to be a powerful tool to give insights into multiple aspects concerning severe accidents: phenomena with the greatest potential to lead to containment failure, safety systems performance and, even, to identify any additional accident management that could mitigate the consequences of such an even, etc. A major result of level-2 PSA is iodine content in Source Term since it is the main responsible for the radiological impact during the first few days after a hypothetical severe accident. Iodine chemistry is known to considerably affect iodine behavior and although understanding has improved substantially since the early 90's, a thorough understanding is still missing and most PSA studies do not address it when assessing severe accident scenarios. This paper emphasizes the quantitative and qualitative significance of considering iodine chemistry in level-2 PSA estimates. To do so a cold leg break, low pressure severe accident sequence of an actual pressurized water reactor has been analyzed with the MELCOR 1.8.6 YT code. Two sets of calculations, with and without chemistry, have been carried out and compared. The study shows that iodine chemistry could result in an iodine release to environment about twice higher, most of which would consist of around 60% of iodine in gaseous form. From these results it is concluded that exploratory studies on the potential effect of iodine chemistry on source term estimates should be carried out. (author)

Estimation of cost per severe accident for improvement of accident protection and consequence mitigation strategies

International Nuclear Information System (INIS)

Silva, Kampanart; Ishiwatari, Yuki; Takahara, Shogo

2013-01-01

To assess the complex situations regarding the severe accidents such as what observed in Fukushima Accident, not only radiation protection aspects but also relevant aspects: health, environmental, economic and societal aspects; must be all included into the consequence assessment. In this study, the authors introduce the “cost per severe accident” as an index to analyze the consequences of severe accidents comprehensively. The cost per severe accident consists of various costs and consequences converted into monetary values. For the purpose of improvement of the accident protection and consequence mitigation strategies, the costs needed to introduce the protective actions, and health and psychological consequences are included in the present study. The evaluations of these costs and consequences were made based on the systematic consequence analysis using level 2 and 3 probabilistic safety assessment (PSA) codes. The accident sequences used in this analysis were taken from the results of level 2 seismic PSA of a virtual 1,100 MWe BWR-5. The doses to the public and the number of people affected were calculated using the level 3 PSA code OSCAAR of Japan Atomic Energy Agency (JAEA). The calculations have been made for 248 meteorological sequences, and the outputs are given as expectation values for various meteorological conditions. Using these outputs, the cost per severe accident is calculated based on the open documents on the Fukushima Accident regarding the cost of protective actions and compensations for psychological harms. Finally, optimized accident protection and consequence mitigation strategies are recommended taking into account the various aspects comprehensively using the cost per severe accident. The authors must emphasize that the aim is not to estimate the accident cost itself but to extend the scope of “risk-informed decision making” for continuous safety improvements of nuclear energy. (author)

Process criticality accident likelihoods, magnitudes and emergency planning. A focus on solution accidents

International Nuclear Information System (INIS)

McLaughlin, Thomas P.

2003-01-01

This paper presents analyses and applications of data from reactor and critical experiment research on the dynamics of nuclear excursions in solution media. Available criticality accident information is also discussed and shown to provide strong evidence of the overwhelming likelihood of accidents in liquid media over other forms and to support the measured data. These analyses are shown to provide valuable insights into key parameters important to understanding solution excursion dynamics in general and in evaluating practical upper bounds on criticality accident magnitudes. This understanding and these upper bounds are directly applicable to the evaluation of the consequences of postulated criticality accidents. These bounds are also essential in order to comply with national and international consensus standards and regulatory requirements for emergency planning. (author)

Benchmarking severe accident computer codes for heavy water reactor applications

Energy Technology Data Exchange (ETDEWEB)

Choi, J.H. [International Atomic Energy Agency, Vienna (Austria)

2010-07-01

Consideration of severe accidents at a nuclear power plant (NPP) is an essential component of the defence in depth approach used in nuclear safety. Severe accident analysis involves very complex physical phenomena that occur sequentially during various stages of accident progression. Computer codes are essential tools for understanding how the reactor and its containment might respond under severe accident conditions. International cooperative research programmes are established by the IAEA in areas that are of common interest to a number of Member States. These co-operative efforts are carried out through coordinated research projects (CRPs), typically 3 to 6 years in duration, and often involving experimental activities. Such CRPs allow a sharing of efforts on an international basis, foster team-building and benefit from the experience and expertise of researchers from all participating institutes. The IAEA is organizing a CRP on benchmarking severe accident computer codes for heavy water reactor (HWR) applications. The CRP scope includes defining the severe accident sequence and conducting benchmark analyses for HWRs, evaluating the capabilities of existing computer codes to predict important severe accident phenomena, and suggesting necessary code improvements and/or new experiments to reduce uncertainties. The CRP has been planned on the advice and with the support of the IAEA Nuclear Energy Department's Technical Working Groups on Advanced Technologies for HWRs. (author)

Comparative modeling analyses of Cs-137 fate in the rivers impacted by Chernobyl and Fukushima accidents

Energy Technology Data Exchange (ETDEWEB)

Zheleznyak, M.; Kivva, S. [Institute of Environmental Radioactivity, Fukushima University (Japan)

2014-07-01

The consequences of two largest nuclear accidents of the last decades - at Chernobyl Nuclear Power Plant (ChNPP) (1986) and at Fukushima Daiichi NPP (FDNPP) (2011) clearly demonstrated that radioactive contamination of water bodies in vicinity of NPP and on the waterways from it, e.g., river- reservoir water after Chernobyl accident and rivers and coastal marine waters after Fukushima accident, in the both cases have been one of the main sources of the public concerns on the accident consequences. The higher weight of water contamination in public perception of the accidents consequences in comparison with the real fraction of doses via aquatic pathways in comparison with other dose components is a specificity of public perception of environmental contamination. This psychological phenomenon that was confirmed after these accidents provides supplementary arguments that the reliable simulation and prediction of the radionuclide dynamics in water and sediments is important part of the post-accidental radioecological research. The purpose of the research is to use the experience of the modeling activities f conducted for the past more than 25 years within the Chernobyl affected Pripyat River and Dnieper River watershed as also data of the new monitoring studies in Japan of Abukuma River (largest in the region - the watershed area is 5400 km{sup 2}), Kuchibuto River, Uta River, Niita River, Natsui River, Same River, as also of the studies on the specific of the 'water-sediment' {sup 137}Cs exchanges in this area to refine the 1-D model RIVTOX and 2-D model COASTOX for the increasing of the predictive power of the modeling technologies. The results of the modeling studies are applied for more accurate prediction of water/sediment radionuclide contamination of rivers and reservoirs in the Fukushima Prefecture and for the comparative analyses of the efficiency of the of the post -accidental measures to diminish the contamination of the water bodies. Document

Accident Analysis and Barrier Function (AEB) Method. Manual for Incident Analysis

International Nuclear Information System (INIS)

Svenson, Ola

2000-02-01

The Accident Analysis and Barrier Function (AEB) Method models an accident or incident as a series of interactions between human and technical systems. In the sequence of human and technical errors leading to an accident there is, in principle, a possibility to arrest the development between each two successive errors. This can be done by a barrier function which, for example, can stop an operator from making an error. A barrier function can be performed by one or several barrier function systems. To illustrate, a mechanical system, a computer system or another operator can all perform a given barrier function to stop an operator from making an error. The barrier function analysis consists of analysis of suggested improvements, the effectiveness of the improvements, the costs of implementation, probability of implementation, the cost of maintaining the barrier function, the probability that maintenance will be kept up to standards and the generalizability of the suggested improvement. The AEB method is similar to the US method called HPES, but differs from that method in different ways. To exemplify, the AEB method has more emphasis on technical errors than HPES. In contrast to HPES that describes a series of events, the AEB method models only errors. This gives a more focused analysis making it well suited for checking other HPES-type accident analyses. However, the AEB method is a generic and stand-alone method that has been applied in other fields than nuclear power, such as, in traffic accident analyses

Accident Analysis and Barrier Function (AEB) Method. Manual for Incident Analysis

Energy Technology Data Exchange (ETDEWEB)

Svenson, Ola [Stockholm Univ. (Sweden). Dept. of Psychology

2000-02-01

The Accident Analysis and Barrier Function (AEB) Method models an accident or incident as a series of interactions between human and technical systems. In the sequence of human and technical errors leading to an accident there is, in principle, a possibility to arrest the development between each two successive errors. This can be done by a barrier function which, for example, can stop an operator from making an error. A barrier function can be performed by one or several barrier function systems. To illustrate, a mechanical system, a computer system or another operator can all perform a given barrier function to stop an operator from making an error. The barrier function analysis consists of analysis of suggested improvements, the effectiveness of the improvements, the costs of implementation, probability of implementation, the cost of maintaining the barrier function, the probability that maintenance will be kept up to standards and the generalizability of the suggested improvement. The AEB method is similar to the US method called HPES, but differs from that method in different ways. To exemplify, the AEB method has more emphasis on technical errors than HPES. In contrast to HPES that describes a series of events, the AEB method models only errors. This gives a more focused analysis making it well suited for checking other HPES-type accident analyses. However, the AEB method is a generic and stand-alone method that has been applied in other fields than nuclear power, such as, in traffic accident analyses.

Approaches to accident analysis in recent US Department of Energy environmental impact statements

International Nuclear Information System (INIS)

Mueller, C.; Folga, S.; Nabelssi, B.

1996-01-01

A review of accident analyses in recent US Department of Energy (DOE) Environmental Impact Statements (EISs) was conducted to evaluate the consistency among approaches and to compare these approaches with existing DOE guidance. The review considered several components of an accident analysis: the overall scope, which in turn should reflect the scope of the EIS; the spectrum of accidents considered; the methods and assumptions used to determine frequencies or frequency ranges for the accident sequences; and the assumption and technical bases for developing radiological and chemical atmospheric source terms and for calculating the consequences of airborne releases. The review also considered the range of results generated with respect to impacts on various worker and general populations. In this paper, the findings of these reviews are presented and methods recommended for improving consistency among EISs and bringing them more into line with existing DOE guidance

Emergency response guide-B ECCS guideline evaluation analyses for N reactor

International Nuclear Information System (INIS)

Chapman, J.C.; Callow, R.A.

1989-07-01

INEL conducted two ECCS analyses for Westinghouse Hanford. Both analyses will assist in the evaluation of proposed changes to the N Reactor Emergency Response Guide-B (ERG-B) Emergency Core System (ECCS) guideline. The analyses were a sensitivity study for reduced-ECCS flow rates and a mechanistically determined confinement steam source for a delayed-ECCS LOCA sequence. The reduced-ECCS sensitivity study established the maximum allowable reduction in ECCS flow as a function of time after core refill for a large break loss-of-coolant accident (LOCA) sequence in the N Reactor. The maximum allowable ECCS flow reduction is defined as the maximum flow reduction for which ECCS continues to provide adequate core cooling. The delayed-ECCS analysis established the liquid and steam break flows and enthalpies during the reflood of a hot core following a delayed ECCS injection LOCA sequence. A simulation of a large, hot leg manifold break with a seven-minute ECCS injection delay was used as a representative LOCA sequence. Both analyses were perform using the RELAP5/MOD2.5 transient computer code. 13 refs., 17 figs., 3 tabs

Accident analysis for transuranic waste management alternatives in the U.S. Department of Energy waste management program

International Nuclear Information System (INIS)

Nabelssi, B.; Mueller, C.; Roglans-Ribas, J.; Folga, S.; Tompkins, M.; Jackson, R.

1995-01-01

Preliminary accident analyses and radiological source term evaluations have been conducted for transuranic waste (TRUW) as part of the US Department of Energy (DOE) effort to manage storage, treatment, and disposal of radioactive wastes at its various sites. The approach to assessing radiological releases from facility accidents was developed in support of the Office of Environmental Management Programmatic Environmental Impact Statement (EM PEIS). The methodology developed in this work is in accordance with the latest DOE guidelines, which consider the spectrum of possible accident scenarios in the implementation of various actions evaluated in an EIS. The radiological releases from potential risk-dominant accidents in storage and treatment facilities considered in the EM PEIS TRUW alternatives are described in this paper. The results show that significant releases can be predicted for only the most severe and extremely improbable accidents sequences

Development of the severe accident risk information database management system SARD

International Nuclear Information System (INIS)

Ahn, Kwang Il; Kim, Dong Ha

2003-01-01

The main purpose of this report is to introduce essential features and functions of a severe accident risk information management system, SARD (Severe Accident Risk Database Management System) version 1.0, which has been developed in Korea Atomic Energy Research Institute, and database management and data retrieval procedures through the system. The present database management system has powerful capabilities that can store automatically and manage systematically the plant-specific severe accident analysis results for core damage sequences leading to severe accidents, and search intelligently the related severe accident risk information. For that purpose, the present database system mainly takes into account the plant-specific severe accident sequences obtained from the Level 2 Probabilistic Safety Assessments (PSAs), base case analysis results for various severe accident sequences (such as code responses and summary for key-event timings), and related sensitivity analysis results for key input parameters/models employed in the severe accident codes. Accordingly, the present database system can be effectively applied in supporting the Level 2 PSA of similar plants, for fast prediction and intelligent retrieval of the required severe accident risk information for the specific plant whose information was previously stored in the database system, and development of plant-specific severe accident management strategies

Development of the severe accident risk information database management system SARD

Energy Technology Data Exchange (ETDEWEB)

Ahn, Kwang Il; Kim, Dong Ha

2003-01-01

The main purpose of this report is to introduce essential features and functions of a severe accident risk information management system, SARD (Severe Accident Risk Database Management System) version 1.0, which has been developed in Korea Atomic Energy Research Institute, and database management and data retrieval procedures through the system. The present database management system has powerful capabilities that can store automatically and manage systematically the plant-specific severe accident analysis results for core damage sequences leading to severe accidents, and search intelligently the related severe accident risk information. For that purpose, the present database system mainly takes into account the plant-specific severe accident sequences obtained from the Level 2 Probabilistic Safety Assessments (PSAs), base case analysis results for various severe accident sequences (such as code responses and summary for key-event timings), and related sensitivity analysis results for key input parameters/models employed in the severe accident codes. Accordingly, the present database system can be effectively applied in supporting the Level 2 PSA of similar plants, for fast prediction and intelligent retrieval of the required severe accident risk information for the specific plant whose information was previously stored in the database system, and development of plant-specific severe accident management strategies.

Sequence analyses and 3D structure prediction of two Type III ...

African Journals Online (AJOL)

Internet

2012-04-17

Apr 17, 2012 ... analyses were performed using the sequence data of growth hormone gene (gh) ... used as a phylogenetic marker for different taxonomic ..... structural changes have been observed in some parts of ..... of spatial restraints.

CFD Analyses of Air-Ingress Accident for VHTRs

Science.gov (United States)

Ham, Tae Kyu

The Very High Temperature Reactor (VHTR) is one of six proposed Generation-IV concepts for the next generation of nuclear powered plants. The VHTR is advantageous because it is able to operate at very high temperatures, thus producing highly efficient electrical generation and hydrogen production. A critical safety event of the VHTR is a loss-of-coolant accident. This accident is initiated, in its worst-case scenario, by a double-ended guillotine break of the cross vessel that connects the reactor vessel and the power conversion unit. Following the depressurization process, the air (i.e., the air and helium mixture) in the reactor cavity could enter the reactor core causing an air-ingress event. In the event of air-ingress into the reactor core, the high-temperature in-core graphite structures will chemically react with the air and could lose their structural integrity. We designed a 1/8th scaled-down test facility to develop an experimental database for studying the mechanisms involved in the air-ingress phenomenon. The current research focuses on the analysis of the air-ingress phenomenon using the computational fluid dynamics (CFD) tool ANSYS FLUENT for better understanding of the air-ingress phenomenon. The anticipated key steps in the air-ingress scenario for guillotine break of VHTR cross vessel are: 1) depressurization; 2) density-driven stratified flow; 3) local hot plenum natural circulation; 4) diffusion into the reactor core; and 5) global natural circulation. However, the OSU air-ingress test facility covers the time from depressurization to local hot plenum natural circulation. Prior to beginning the CFD simulations for the OSU air-ingress test facility, benchmark studies for the mechanisms which are related to the air-ingress accident, were performed to decide the appropriate physical models for the accident analysis. In addition, preliminary experiments were performed with a simplified 1/30th scaled down acrylic set-up to understand the air

A tool for safety officers when analysing the basic causes of simple accidents

DEFF Research Database (Denmark)

Jørgensen, Kirsten

Most accidents that happen in enterprises are simple and seldom have serious invalidating consequences. Very often these kinds of accident are not investigated and if they are, then the investigation is very brief, with comments such as that it was the victim’s own fault or just an unlucky...... for some years with interesting results. Both the difficulties and the benefits will be presented, together with examples of the use of the tool. The main purpose of the tool is to demonstrate how management and workers can get a much better understanding of why accidents happen, even those accidents...... that seem to be unavoidable, and that simple accidents never are simple, but always have root causes on which preventive action can be focused....

Fukushima, one year later. Initial analyses of the accident and its consequences

International Nuclear Information System (INIS)

2012-01-01

The earthquake of magnitude 9 of March 11, 2011 with an epicenter 80 km east of the Japanese island of Honshu, and the subsequent tsunami, severely affected the region of Tohoku, with major consequences for its population and infrastructure. Devastating the site of the Fukushima Dai-ichi nuclear power plant, these natural events were the cause of the core meltdowns of three nuclear reactors and the loss of cooling of several spent fuel pools. Explosions also occurred in reactor buildings 1 through 4 due to hydrogen produced during fuel degradation. Very significant radioactive releases into the environment took place. The accident was classified level 7 on the International Nuclear Event Scale (INES). This report provides an assessment and perspective on the information gathered by IRSN during the first twelve months following the disaster in an effort to understand the condition of the installations, evaluate the releases and analyze and evaluate the consequences of the accident on workers and the impact on the population and the environment. On the basis of available information, the report provides an initial analysis of the chain of events. It should be noted that a year after the accident, the full sequence of events is still not understood. Operating experience feedback from the 1979 Three Mile Island accident in the United States, in which reactor core damage was not confirmed until 1986, suggests that it may be several years before a detailed scenario can be constructed of the accident that led to radioactive releases. It will require access to the damaged installations. The situation at the site remains dangerous (reactor pressure vessels and containments are not leak-tight, diffuse releases, etc.). If it has significantly improved as a result of the significant resources deployed by the Tokyo Electro Power Company (TEPCO) to regain control of the installations, this effort must continue over the long term to begin evacuation of fuel from pools (in two

Examination of some assumed severe reactor accidents at the Olkiluoto nuclear power plant

International Nuclear Information System (INIS)

Pekkarinen, E.; Rossi, J.

1989-02-01

Knowledge and analysis methods of severe accidents at nuclear power plants and of subsequent response of primary system and containment have been developed in last few years to the extent that realistic source tems of the specified accident sequences can be calculated for the Finnish nuclear power plants. The objective of this investigation was to calculate the source terms of off-site consequences brought about by some selected severe accident sequences initiated by the total loss of on-site and off-site AC power at the Olkiluoto nuclear power plant. The results describing the estimated off-site health risks are expressed as conditional assuming that the accident has taken place, because the probabilities of the occurence of the accident sequences considered have not been analysed in this study. The range and probabilities of occurence of health detriments are considered by calculating consequences in different weeather conditions and taking into account the annual frequency of each weather condition and statistical population distribution. The calculational results indicate that the reactor building provides and additional holdup and deposition of radioactive substance (except coble gases) released from the containment. Furthermore, the release fractions of the core inventory to the environment of volatile fission products such as iodine, cesium and tellurium remain under 0.03. No early health effects are predicted for the surrounding population in case the assumed short-tem countermeasures are performed effectively. Acute health effects are extremely improbable even without any active countermeasure. By reducing the long-term exposure from contaminated agricultural products, the collective dose from natural long-term background radiation, for instance in the sector of 30 degrees towards the southern Finland up to the distance of 300 kilometers, would be expected to increase with 2-20 percent depending on the release considered

Probabilistic Accident Progression Analysis with application to a LMFBR design

International Nuclear Information System (INIS)

Jamali, K.M.

1982-01-01

A method for probabilistic analysis of accident sequences in nuclear power plant systems referred to as ''Probabilistic Accident Progression Analysis'' (PAPA) is described. Distinctive features of PAPA include: (1) definition and analysis of initiator-dependent accident sequences on the component level; (2) a new fault-tree simplification technique; (3) a new technique for assessment of the effect of uncertainties in the failure probabilities in the probabilistic ranking of accident sequences; (4) techniques for quantification of dependent failures of similar components, including an iterative technique for high-population components. The methodology is applied to the Shutdown Heat Removal System (SHRS) of the Clinch River Breeder Reactor Plant during its short-term (0 -2 . Major contributors to this probability are the initiators loss of main feedwater system, loss of offsite power, and normal shutdown

Pressure Load Analysis during Severe Accidents for the Evaluation of Late Containment Failure in OPR-1000

Energy Technology Data Exchange (ETDEWEB)

Park, S. Y.; Ahn, K. I. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

The MAAP code is a system level computer code capable of performing integral analyses of potential severe accident progressions in nuclear power plants, whose main purpose is to support a level 2 probabilistic safety assessment or severe accident management strategy developments. The code employs lots of user-options for supporting a sensitivity and uncertainty analysis. The present application is mainly focused on determining an estimate of the containment building pressure load caused by severe accident sequences. Key modeling parameters and phenomenological models employed for the present uncertainty analysis are closely related to in-vessel hydrogen generation, gas combustion in the containment, corium distribution in the containment after a reactor vessel failure, corium coolability in the reactor cavity, and molten-corium interaction with concrete. The phenomenology of severe accidents is extremely complex. In this paper, a sampling-based phenomenological uncertainty analysis was performed to statistically quantify uncertainties associated with the pressure load of a containment building for a late containment failure evaluation, based on the key modeling parameters employed in the MAAP code and random samples for those parameters. Phenomenological issues surrounding the late containment failure mode are highly complex. Included are the pressurization owing to steam generation in the cavity, molten corium-concrete interaction, late hydrogen burn in the containment, and the secondary heat removal availability. The methodology and calculation results can be applied for the optimum assessment of a late containment failure model. The accident sequences considered were a loss of coolant accidents and loss of offsite accidents expected in the OPR-1000 plant. As a result, uncertainties addressed in the pressure load of the containment building were quantified as a function of time. A realistic evaluation of the mean and variance estimates provides a more complete

Containment integrity analysis under accidents

International Nuclear Information System (INIS)

Lin Chengge; Zhao Ruichang; Liu Zhitao

2010-01-01

Containment integrity analyses for current nuclear power plants (NPPs) mainly focus on the internal pressure caused by design basis accidents (DBAs). In addition to the analyses of containment pressure response caused by DBAs, the behavior of containment during severe accidents (SAs) are also evaluated for AP1000 NPP. Since the conservatism remains in the assumptions,boundary conditions and codes, margin of the results of containment integrity analyses may be overestimated. Along with the improvements of the knowledge to the phenomena and process of relevant accidents, the margin overrated can be appropriately reduced by using the best estimate codes combined with the uncertainty methods, which could be beneficial to the containment design and construction of large passive plants (LPP) in China. (authors)

MELCOR assessment of sequential severe accident mitigation actions under SGTR accident

International Nuclear Information System (INIS)

Choi, Wonjun; Jeon, Joongoo; Kim, Nam Kyung; Kim, Sung Joong

2017-01-01

The representative example of the severe accident studies using the severe accident code is investigation of effectiveness of developed severe accident management (SAM) strategy considering the positive and adverse effects. In Korea, some numerical studies were performed to investigate the SAM strategy using various severe accident codes. Seo et.al performed validation of RCS depressurization strategy and investigated the effect of severe accident management guidance (SAMG) entry condition under small break loss of coolant accident (SBLOCA) without safety injection (SI), station blackout (SBO), and total loss of feed water (TLOFW) scenarios. The SGTR accident with the sequential mitigation actions according to the flow chart of SAMG was simulated by the MELCOR 1.8.6 code. Three scenariospreventing the RPV failure were investigated in terms of fission product release, hydrogen risk, and the containment pressure. Major conclusions can be summarized as follows: (1) According to the flow chart of SAMG, RPV failure can be prevented depending on the method of RCS depressurization. (2) To reduce the release of fission product during the injecting into SGs, a temporary opening of SDS before the injecting into SGs was suggested. These modified sequences of mitigation actions can reduce the release of fission product and the adverse effect of SDS.

Accidents in the construction industry in the Netherlands: An analysis of accident reports using Storybuilder

International Nuclear Information System (INIS)

Ale, B.J.M.; Bellamy, L.J.; Baksteen, H.; Damen, M.; Goossens, L.H.J.; Hale, A.R.; Mud, M.; Oh, J.; Papazoglou, I.A.; Whiston, J.Y.

2008-01-01

As part of an ongoing effort by the Ministry of Social Affairs and Employment of the Netherlands, a research project is being undertaken to construct a causal model for occupational risk. This model should provide quantitative insight into the causes and consequences of occupational accidents. One of the components of the model is a tool to systematically classify and analyse reports of past accidents. This tool 'Storybuilder' was described in earlier papers. In this paper, Storybuilder is used to analyse the causes of accidents reported in the database of the Dutch Labour Inspectorate involving people working in the construction industry. Conclusions are drawn on measures to reduce the accident probability. Some of these conclusions are contrary to common beliefs in the industry

Application of the severe accident code ATHLET-CD. Modelling and evaluation of accident management measures (Project WASA-BOSS)

Energy Technology Data Exchange (ETDEWEB)

Wilhelm, Polina; Jobst, Matthias; Kliem, Soeren; Kozmenkov, Yaroslav; Schaefer, Frank [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Reactor Safety

2016-07-01

The improvement of the safety of nuclear power plants is a continuously on-going process. The analysis of transients and accidents is an important research topic, which significantly contributes to safety enhancements of existing power plants. In case of an accident with multiple failures of safety systems core uncovery and heat-up can occur. In order to prevent the accident to turn into a severe one or to mitigate the consequences of severe accidents, different accident management measures can be applied. Numerical analyses are used to investigate the accident progression and the complex physical phenomena during the core degradation phase, as well as to evaluate the effectiveness of possible countermeasures in the preventive and mitigative domain [1, 2]. The presented analyses have been performed with the computer code ATHLET-CD developed by GRS [3, 4].

A database system for the management of severe accident risk information, SARD

International Nuclear Information System (INIS)

Ahn, K. I.; Kim, D. H.

2003-01-01

The purpose of this paper is to introduce main features and functions of a PC Windows-based database management system, SARD, which has been developed at Korea Atomic Energy Research Institute for automatic management and search of the severe accident risk information. Main functions of the present database system are implemented by three closely related, but distinctive modules: (1) fixing of an initial environment for data storage and retrieval, (2) automatic loading and management of accident information, and (3) automatic search and retrieval of accident information. For this, the present database system manipulates various form of the plant-specific severe accident risk information, such as dominant severe accident sequences identified from the plant-specific Level 2 Probabilistic Safety Assessment (PSA) and accident sequence-specific information obtained from the representative severe accident codes (e.g., base case and sensitivity analysis results, and summary for key plant responses). The present database system makes it possible to implement fast prediction and intelligent retrieval of the required severe accident risk information for various accident sequences, and in turn it can be used for the support of the Level 2 PSA of similar plants and for the development of plant-specific severe accident management strategies

A database system for the management of severe accident risk information, SARD

Energy Technology Data Exchange (ETDEWEB)

Ahn, K. I.; Kim, D. H. [KAERI, Taejon (Korea, Republic of)

2003-10-01

The purpose of this paper is to introduce main features and functions of a PC Windows-based database management system, SARD, which has been developed at Korea Atomic Energy Research Institute for automatic management and search of the severe accident risk information. Main functions of the present database system are implemented by three closely related, but distinctive modules: (1) fixing of an initial environment for data storage and retrieval, (2) automatic loading and management of accident information, and (3) automatic search and retrieval of accident information. For this, the present database system manipulates various form of the plant-specific severe accident risk information, such as dominant severe accident sequences identified from the plant-specific Level 2 Probabilistic Safety Assessment (PSA) and accident sequence-specific information obtained from the representative severe accident codes (e.g., base case and sensitivity analysis results, and summary for key plant responses). The present database system makes it possible to implement fast prediction and intelligent retrieval of the required severe accident risk information for various accident sequences, and in turn it can be used for the support of the Level 2 PSA of similar plants and for the development of plant-specific severe accident management strategies.

Detailed evaluation of RCS boundary rupture during high-pressure severe accident sequences

International Nuclear Information System (INIS)

Park, Rae-Joon; Hong, Seong-Wan

2011-01-01

A depressurization possibility of the reactor coolant system (RCS) before a reactor vessel rupture during a high-pressure severe accident sequence has been evaluated for the consideration of direct containment heating (DCH) and containment bypass. A total loss of feed water (TLOFW) and a station blackout (SBO) of the advanced power reactor 1400 (APR 1400) has been evaluated from an initiating event to a creep rupture of the RCS boundary by using the SCDAP/RELAP5 computer code. In addition, intentional depressurization of the RCS using power-operated safety relief valves (POSRVs) has been evaluated. The SCDAPRELAP5 results have shown that the pressurizer surge line broke before the reactor vessel rupture failure, but a containment bypass did not occur because steam generator U tubes did not break. The intentional depressurization of the RCS using POSRV was effective for the DCH prevention at a reactor vessel rupture. (author)

Accident Analyses for Conversion of the University of Missouri Research Reactor (MURR) from Highly-Enriched to Low-Enriched Uranium

Energy Technology Data Exchange (ETDEWEB)

Stillman, J. A. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Div., Research and Test Reactor Dept.; Feldman, E. E. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Div., Research and Test Reactor Dept.; Wilson, E. H. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Div., Research and Test Reactor Dept.; Foyto, L. P. [Univ. of Missouri, Columbia, MO (United States). Research Reactor; Kutikkad, K. [Univ. of Missouri, Columbia, MO (United States). Research Reactor; McKibben, J. C. [Univ. of Missouri, Columbia, MO (United States). Research Reactor; Peters, N. J. [Univ. of Missouri, Columbia, MO (United States). Research Reactor; Cowherd, W. M. [Univ. of Missouri, Columbia, MO (United States). College of Engineering, Nuclear Engineering Program; Rickman, B. [Univ. of Missouri, Columbia, MO (United States). College of Engineering, Nuclear Engineering Program

2014-12-01

This report contains the results of reactor accident analyses for the University of Missouri Research Reactor (MURR). The calculations were performed as part of the conversion from the use of highly-enriched uranium (HEU) fuel to the use of low-enriched uranium (LEU) fuel. The analyses were performed by staff members of the Global Threat Reduction Initiative (GTRI) Reactor Conversion Program at the Argonne National Laboratory (ANL), the MURR Facility, and the Nuclear Engineering Program – College of Engineering, University of Missouri-Columbia. The core conversion to LEU is being performed with financial support from the U. S. government. This report contains the results of reactor accident analyses for the University of Missouri Research Reactor (MURR). The calculations were performed as part of the conversion from the use of highly-enriched uranium (HEU) fuel to the use of low-enriched uranium (LEU) fuel. The analyses were performed by staff members of the Global Threat Reduction Initiative (GTRI) Reactor Conversion Program at the Argonne National Laboratory (ANL), the MURR Facility, and the Nuclear Engineering Program – College of Engineering, University of Missouri-Columbia. The core conversion to LEU is being performed with financial support from the U. S. government. In the framework of non-proliferation policies, the international community presently aims to minimize the amount of nuclear material available that could be used for nuclear weapons. In this geopolitical context most research and test reactors, both domestic and international, have started a program of conversion to the use of LEU fuel. A new type of LEU fuel based on an alloy of uranium and molybdenum (U-Mo) is expected to allow the conversion of U.S. domestic high performance reactors like MURR. This report presents the results of a study of core behavior under a set of accident conditions for MURR cores fueled with HEU U-Alx dispersion fuel or LEU monolithic U-Mo alloy fuel with 10 wt% Mo

The effect of system modeling on the Fukushima accident evolution

Energy Technology Data Exchange (ETDEWEB)

Herranz, L.E.; Fontanet, J.; López, C.; Fernández, E.

2015-07-01

The Fukushima accident is becoming both a unique opportunity and a huge challenge for severe accident analysis. The OECD-BSAF project has articulated a good part of the modeling efforts conducted so far. Inside this project, CIEMAT has conducted forensic analyses of the Fukushima accident in units 1 through 3 with MELCOR 2.1 and it has postulated a set of accident scenarios consistent with data. Beyond specific results, sensitivity analyses on safety systems performance and prevailing boundary conditions have highlighted the need of conducting uncertainty analyses when modeling NPPs severe accident scenarios. (Author)

Reactivity initiated accident analyses for the safety assessment of upgraded JRR-3

International Nuclear Information System (INIS)

Harami, Taikan; Uemura, Mutsumi; Ohnishi, Nobuaki

1984-08-01

JRR-3, currently a heavy water moderated and cooled 10 MW reactor, is to be upgraded to a light water moderated and cooled, heavy water reflected 20 MW reactor. This report describes the analytical results of reactivity initiated accidents for the safety assessment of upgraded JRR-3. The following five cases have been selected for the assessment; (1) uncontrolled control rod withdrawal from zero power, (2) uncontrolled control rod withdrawal from full power, (3) removal of irradiation samples, (4) increase of primary coolant flow, (5) failure of heavy water tank. Parameter studies have been made for each of the above cases to cover possible uncertainties. All analyses have been made by a computer code EUREKA-2. The results show that the safety criteria for upgraded JRR-3 are all met and the adequacy of the design is confirmed. (author)

Accident source terms for pressurized water reactors with high-burnup cores calculated using MELCOR 1.8.5.

Energy Technology Data Exchange (ETDEWEB)

Gauntt, Randall O.; Powers, Dana Auburn; Ashbaugh, Scott G.; Leonard, Mark Thomas; Longmire, Pamela

2010-04-01

In this study, risk-significant pressurized-water reactor severe accident sequences are examined using MELCOR 1.8.5 to explore the range of fission product releases to the reactor containment building. Advances in the understanding of fission product release and transport behavior and severe accident progression are used to render best estimate analyses of selected accident sequences. Particular emphasis is placed on estimating the effects of high fuel burnup in contrast with low burnup on fission product releases to the containment. Supporting this emphasis, recent data available on fission product release from high-burnup (HBU) fuel from the French VERCOR project are used in this study. The results of these analyses are treated as samples from a population of accident sequences in order to employ approximate order statistics characterization of the results. These trends and tendencies are then compared to the NUREG-1465 alternative source term prescription used today for regulatory applications. In general, greater differences are observed between the state-of-the-art calculations for either HBU or low-burnup (LBU) fuel and the NUREG-1465 containment release fractions than exist between HBU and LBU release fractions. Current analyses suggest that retention of fission products within the vessel and the reactor coolant system (RCS) are greater than contemplated in the NUREG-1465 prescription, and that, overall, release fractions to the containment are therefore lower across the board in the present analyses than suggested in NUREG-1465. The decreased volatility of Cs2MoO4 compared to CsI or CsOH increases the predicted RCS retention of cesium, and as a result, cesium and iodine do not follow identical behaviors with respect to distribution among vessel, RCS, and containment. With respect to the regulatory alternative source term, greater differences are observed between the NUREG-1465 prescription and both HBU and LBU predictions than exist between HBU and LBU

HANARO thermal hydraulic accident analysis

Energy Technology Data Exchange (ETDEWEB)

Park, Chul; Kim, Heon Il; Lee, Bo Yook; Lee, Sang Yong [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1996-06-01

For the safety assessment of HANARO, accident analyses for the anticipated operational transients, accident scenarios and limiting accident scenarios were conducted. To do this, the commercial nuclear reactor system code. RELAP5/MOD2 was modified to RELAP5/KMRR; the thermal hydraulic correlations and the heat exchanger model was changed to incorporate HANARO characteristics. This report summarizes the RELAP/KMRR calculation results and the subchannel analyses results based on the RELAP/KMRR results. During the calculation, major concern was placed on the integrity of the fuel. For all the scenarios, the important accident analysis parameters, i.e., fuel centerline temperatures and the minimum critical heat flux ratio(MCHFR), satisfied safe design limits. It was verified, therefore, that the HANARO was safely designed. 21 tabs., 89 figs., 39 refs. (Author) .new.

A weighted U-statistic for genetic association analyses of sequencing data.

Science.gov (United States)

Wei, Changshuai; Li, Ming; He, Zihuai; Vsevolozhskaya, Olga; Schaid, Daniel J; Lu, Qing

2014-12-01

With advancements in next-generation sequencing technology, a massive amount of sequencing data is generated, which offers a great opportunity to comprehensively investigate the role of rare variants in the genetic etiology of complex diseases. Nevertheless, the high-dimensional sequencing data poses a great challenge for statistical analysis. The association analyses based on traditional statistical methods suffer substantial power loss because of the low frequency of genetic variants and the extremely high dimensionality of the data. We developed a Weighted U Sequencing test, referred to as WU-SEQ, for the high-dimensional association analysis of sequencing data. Based on a nonparametric U-statistic, WU-SEQ makes no assumption of the underlying disease model and phenotype distribution, and can be applied to a variety of phenotypes. Through simulation studies and an empirical study, we showed that WU-SEQ outperformed a commonly used sequence kernel association test (SKAT) method when the underlying assumptions were violated (e.g., the phenotype followed a heavy-tailed distribution). Even when the assumptions were satisfied, WU-SEQ still attained comparable performance to SKAT. Finally, we applied WU-SEQ to sequencing data from the Dallas Heart Study (DHS), and detected an association between ANGPTL 4 and very low density lipoprotein cholesterol. © 2014 WILEY PERIODICALS, INC.

Severe accident considerations for modern KWU-PWR plants

International Nuclear Information System (INIS)

Eyink, J.

1987-01-01

In assumption of severe accident on modern KWU-PWR plants the author discusses on the: selection of core meltdown sequences, course of the accident, containment behaviour and source terms for fission products release to the environment

Overview of core disruptive accidents

International Nuclear Information System (INIS)

Marchaterre, J.F.

1977-01-01

An overview of the analysis of core-disruptive accidents is given. These analyses are for the purpose of understanding and predicting fast reactor behavior in severe low probability accident conditions, to establish the consequences of such conditions and to provide a basis for evaluating consequence limiting design features. The methods are used to analyze core-disruptive accidents from initiating event to complete core disruption, the effects of the accident on reactor structures and the resulting radiological consequences are described

Accident analysis for nuclear power plants

International Nuclear Information System (INIS)

2002-01-01

Deterministic safety analysis (frequently referred to as accident analysis) is an important tool for confirming the adequacy and efficiency of provisions within the defence in depth concept for the safety of nuclear power plants (NPPs). Owing to the close interrelation between accident analysis and safety, an analysis that lacks consistency, is incomplete or is of poor quality is considered a safety issue for a given NPP. Developing IAEA guidance documents for accident analysis is thus an important step towards resolving this issue. Requirements and guidelines pertaining to the scope and content of accident analysis have, in the past, been partially described in various IAEA documents. Several guidelines relevant to WWER and RBMK type reactors have been developed within the IAEA Extrabudgetary Programme on the Safety of WWER and RBMK NPPs. To a certain extent, accident analysis is also covered in several documents of the revised NUSS series, for example, in the Safety Requirements on Safety of Nuclear Power Plants: Design (NS-R-1) and in the Safety Guide on Safety Assessment and Verification for Nuclear Power Plants (NS-G-1.2). Consistent with these documents, the IAEA has developed the present Safety Report on Accident Analysis for Nuclear Power Plants. Many experts have contributed to the development of this Safety Report. Besides several consultants meetings, comments were collected from more than fifty selected organizations. The report was also reviewed at the IAEA Technical Committee Meeting on Accident Analysis held in Vienna from 30 August to 3 September 1999. The present IAEA Safety Report is aimed at providing practical guidance for performing accident analyses. The guidance is based on present good practice worldwide. The report covers all the steps required to perform accident analyses, i.e. selection of initiating events and acceptance criteria, selection of computer codes and modelling assumptions, preparation of input data and presentation of the

Reactor Safety Gap Evaluation of Accident Tolerant Components and Severe Accident Analysis

International Nuclear Information System (INIS)

Farmer, Mitchell T.; Bunt, R.; Corradini, M.; Ellison, Paul B.; Francis, M.; Gabor, John D.; Gauntt, R.; Henry, C.; Linthicum, R.; Luangdilok, W.; Lutz, R.; Paik, C.; Plys, M.; Rabiti, Cristian; Rempe, J.; Robb, K.; Wachowiak, R.

2015-01-01

The overall objective of this study was to conduct a technology gap evaluation on accident tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist, given the current state of light water reactor (LWR) severe accident research, and additionally augmented by insights obtained from the Fukushima accident. The ultimate benefit of this activity is that the results can be used to refine the Department of Energy's (DOE) Reactor Safety Technology (RST) research and development (R&D) program plan to address key knowledge gaps in severe accident phenomena and analyses that affect reactor safety and that are not currently being addressed by the industry or the Nuclear Regulatory Commission (NRC).

Reactor Safety Gap Evaluation of Accident Tolerant Components and Severe Accident Analysis

Energy Technology Data Exchange (ETDEWEB)

Farmer, Mitchell T. [Argonne National Lab. (ANL), Argonne, IL (United States); Bunt, R. [Southern Nuclear, Atlanta, GA (United States); Corradini, M. [Univ. of Wisconsin, Madison, WI (United States); Ellison, Paul B. [GE Power and Water, Duluth, GA (United States); Francis, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Gabor, John D. [Erin Engineering, Walnut Creek, CA (United States); Gauntt, R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Henry, C. [Fauske and Associates, Burr Ridge, IL (United States); Linthicum, R. [Exelon Corp., Chicago, IL (United States); Luangdilok, W. [Fauske and Associates, Burr Ridge, IL (United States); Lutz, R. [PWR Owners Group (PWROG); Paik, C. [Fauske and Associates, Burr Ridge, IL (United States); Plys, M. [Fauske and Associates, Burr Ridge, IL (United States); Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rempe, J. [Rempe and Associates LLC, Idaho Falls, ID (United States); Robb, K. [Argonne National Lab. (ANL), Argonne, IL (United States); Wachowiak, R. [Electric Power Research Inst. (EPRI), Knovville, TN (United States)

2015-01-31

The overall objective of this study was to conduct a technology gap evaluation on accident tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist, given the current state of light water reactor (LWR) severe accident research, and additionally augmented by insights obtained from the Fukushima accident. The ultimate benefit of this activity is that the results can be used to refine the Department of Energy’s (DOE) Reactor Safety Technology (RST) research and development (R&D) program plan to address key knowledge gaps in severe accident phenomena and analyses that affect reactor safety and that are not currently being addressed by the industry or the Nuclear Regulatory Commission (NRC).

Chapter No.4. Safety analyses

International Nuclear Information System (INIS)

2002-01-01

In 2001 the activity in the field of safety analyses was focused on verification of the safety analyses reports for NPP V-2 Bohunice and NPP Mochovce concerning the new profiled fuel and probabilistic safety assessment study for NPP Mochovce. The calculation safety analyses were performed and expert reviews for the internal UJD needs were elaborated. An important part of work was performed also in solving of scientific and technical tasks appointed within bilateral projects of co-operation between UJD and its international partnership organisations as well as within international projects ordered and financed by the European Commission. All these activities served as an independent support for UJD in its deterministic and probabilistic safety assessment of nuclear installations. A special attention was paid to a review of probabilistic safety assessment study of level 1 for NPP Mochovce. The probabilistic safety analysis of NPP related to the full power operation was elaborated in the study and a contribution of the technical and operational improvements to the risk decreasing was quantified. A core damage frequency of the reactor was calculated and the dominant initiating events and accident sequences with the major contribution to the risk were determined. The target of the review was to determine the acceptance of the sources of input information, assumptions, models, data, analyses and obtained results, so that the probabilistic model could give a real picture of the NPP. The review of the study was performed in co-operation of UJD with the IAEA (IPSART mission) as well as with other external organisations, which were not involved in the elaboration of the reviewed document and probabilistic model of NPP. The review was made in accordance with the IAEA guidelines and methodical documents of UJD and US NRC. In the field of calculation safety analyses the UJD activity was focused on the analysis of an operational event, analyses of the selected accident scenarios

JAERI's activities in JCO accident

International Nuclear Information System (INIS)

2000-09-01

The Japan Atomic Energy Research Institute (JAERI) was actively involved in a variety of technical supports and cooperative activities, such as advice on terminating the criticality condition, contamination checks of the residents and consultation services for the residents, as emergency response actions to the criticality accident at the uranium processing facility operated by the JCO Co. Ltd., which occurred on September 30, 1999. These activities were carried out in collaborative ways by the JAERI staff from the Tokai Research Establishment, Naka Fusion Research Establishment, Oarai Research Establishment, and Headquarter Office in Tokyo. As well, the JAERI was engaged in the post-accident activities such as identification of accident causes, analyses of the criticality accident, and dose assessment of exposed residents, to support the Headquarter for Accident Countermeasures of the Science and Technology Agency (STA), the Accident Investigation Committee and the Health Control Committee of the Nuclear Safety Commission of Japan (NSC). This report compiles the activities, that the JAERI has conducted to date, including the discussions on measures for terminating the criticality condition, evaluation of the fission number, radiation monitoring in the environment, dose assessment, analyses of criticality dynamics. (author)

Safety and risk questions following the nuclear incidents and accidents in Japan. Summary final report; Sicherheits- und Risikofragen im Nachgang zu den nuklearen Stoer- und Unfaellen in Japan. Zusammenfassender Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Mildenberger, Oliver

2015-03-15

After the nuclear accidents in Japan, GRS has carried out in-depth investigations of the events. On the one hand, the accident sequences in the affected units have been analysed from various viewpoints. On the other hand, the transferability of the findings to German plants has been examined to possibly make recommendations for safety improvements. The accident sequences at Fukushima Daiichi have been traced with as much detail as possible based on all available information. Additional insights have been drawn from thermohydraulic analyses with the GRS code system ATHLET-CD/COCOSYS focusing on the events in units 2 and 3, e.g. with regard to core damage and the state of the containments in the first days of the accident sequence. In-depth investigations have also been carried out on topics such as natural external hazards, electrical power supply or organizational measures. In addition, methodological studies on further topics related with the accidents have been performed. Through a detailed analysis of the relevant data from the events in Japan, the basis for an in-depth examination of the transferability to German plants was created. It was found that an implementation of most of the insights gained from the investigations had already been initiated as part of the GRS information notice 2012/02. Further findings have been communicated to the federal government and introduced into other relevant bodies, e.g. the Nuclear Safety Standards Committee (KTA) or the Reactor Safety Commission (RSK).

Radiation physics and shielding codes and analyses applied to design-assist and safety analyses of CANDUR and ACRTM reactors

International Nuclear Information System (INIS)

Aydogdu, K.; Boss, C. R.

2006-01-01

This paper discusses the radiation physics and shielding codes and analyses applied in the design of CANDU and ACR reactors. The focus is on the types of analyses undertaken rather than the inputs supplied to the engineering disciplines. Nevertheless, the discussion does show how these analyses contribute to the engineering design. Analyses in radiation physics and shielding can be categorized as either design-assist or safety and licensing (accident) analyses. Many of the analyses undertaken are designated 'design-assist' where the analyses are used to generate recommendations that directly influence plant design. These recommendations are directed at mitigating or reducing the radiation hazard of the nuclear power plant with engineered systems and components. Thus the analyses serve a primary safety function by ensuring the plant can be operated with acceptable radiation hazards to the workers and public. In addition to this role of design assist, radiation physics and shielding codes are also deployed in safety and licensing assessments of the consequences of radioactive releases of gaseous and liquid effluents during normal operation and gaseous effluents following accidents. In the latter category, the final consequences of accident sequences, expressed in terms of radiation dose to members of the public, and inputs to accident analysis, e.g., decay heat in fuel following a loss-of-coolant accident, are also calculated. Another role of the analyses is to demonstrate that the design of the plant satisfies the principle of ALARA (as low as reasonably achievable) radiation doses. This principle is applied throughout the design process to minimize worker and public doses. The principle of ALARA is an inherent part of all design-assist recommendations and safety and licensing assessments. The main focus of an ALARA exercise at the design stage is to minimize the radiation hazards at the source. This exploits material selection and impurity specifications and relies

Review of the SIMMER-II analyses of liquid-metal-cooled fast breeder reactor core-disruptive accident fuel escape

International Nuclear Information System (INIS)

DeVault, G.P.; Bell, C.R.

1985-01-01

Early fuel removal from the active core of a liquid-metal-cooled fast breeder reactor undergoing a core-disruptive accident may reduce the potential for large energetics resulting from recriticalities. This paper presents a review of analyses with the SIMMER-II computer program of the effectiveness of possible fuel escape paths. Where possible, how SIMMER-II compares with or is validated against experiments that simulated the escape paths also is discussed

Accident sequences and causes analysis in a hydrogen production process

Energy Technology Data Exchange (ETDEWEB)

Jae, Moo Sung; Hwang, Seok Won; Kang, Kyong Min; Ryu, Jung Hyun; Kim, Min Soo; Cho, Nam Chul; Jeon, Ho Jun; Jung, Gun Hyo; Han, Kyu Min; Lee, Seng Woo [Hanyang Univ., Seoul (Korea, Republic of)

2006-03-15

Since hydrogen production facility using IS process requires high temperature of nuclear power plant, safety assessment should be performed to guarantee the safety of facility. First of all, accident cases of hydrogen production and utilization has been surveyed. Based on the results, risk factors which can be derived from hydrogen production facility were identified. Besides the correlation between risk factors are schematized using influence diagram. Also initiating events of hydrogen production facility were identified and accident scenario development and quantification were performed. PSA methodology was used for identification of initiating event and master logic diagram was used for selection method of initiating event. Event tree analysis was used for quantification of accident scenario. The sum of all the leakage frequencies is 1.22x10{sup -4} which is similar value (1.0x10{sup -4}) for core damage frequency that International Nuclear Safety Advisory Group of IAEA suggested as a criteria.

Expert software for accident identification

International Nuclear Information System (INIS)

Dobnikar, M.; Nemec, T.; Muehleisen, A.

2003-01-01

Each type of an accident in a Nuclear Power Plant (NPP) causes immediately after the start of the accident variations of physical parameters that are typical for that type of the accident thus enabling its identification. Examples of these parameter are: decrease of reactor coolant system pressure, increase of radiation level in the containment, increase of pressure in the containment. An expert software enabling a fast preliminary identification of the type of the accident in Krsko NPP has been developed. As input data selected typical parameters from Emergency Response Data System (ERDS) of the Krsko NPP are used. Based on these parameters the expert software identifies the type of the accident and also provides the user with appropriate references (past analyses and other documentation of such an accident). The expert software is to be used as a support tool by an expert team that forms in case of an emergency at Slovenian Nuclear Safety Administration (SNSA) with the task to determine the cause of the accident, its most probable scenario and the source term. The expert software should provide initial identification of the event, while the final one is still to be made after appropriate assessment of the event by the expert group considering possibility of non-typical events, multiple causes, initial conditions, influences of operators' actions etc. The expert software can be also used as an educational/training tool and even as a simple database of available accident analyses. (author)

Fukushima. The accident sequence and important causes. Pt. 2/3; Fukushima. Unfallablauf und wesentliche Ursachen. T. 2/3

Energy Technology Data Exchange (ETDEWEB)

Pistner, Christoph [Oeko-Institut e.V., Darmstadt (Germany). Bereich Nukleartechnik und Anlagensicherheit

2013-07-01

In this part on the accident sequence in the NPP Fukushima Daiichi on March 11, 2011 the important safety systems of a nuclear power plant are described, including the design of a nuclear boiling water reactor with Mark-II type containment, the high-pressure injection system and the systems for afterheat removal. The chronology of the accident progress in the NPP units 1-3 is described. The units 4-6 were shutdown due to revision work. Due to the earthquake an electric power transformation station close to the NPP site and the power poles were destroyed, the redundant power supply of the neighboring electricity supplier Tohoku did not work. All emergency diesel generators were flooded and destroyed resulting in the so-called station blackout. Firefighting trucks and materials for radiation protection and the infrastructure at the NPP site were destroyed. The release of radioactivity induced a severe contamination of the reactor site.

Simulation of severe accident using March-3 computer code

International Nuclear Information System (INIS)

Fernandes, A.; Nakata, H.

1991-01-01

The severe accident sensitivity analysis utilizing the March-3 approximate modelization options has been performed. The reference results against which the present results have been compared were obtained from the best published results for the most representative accident sequences: TMLU, S sub(2)DC sub(r) and S sub(2)DCF sub(r) for the Zion-1 reactor. The results of the present sensitivity analysis revealed the presence of very crude modelizations, in the March-3 program, to represent the critical phenomenologies involved in the severe accident sequences considered, even though large uncertainties must still be taken into account due primarily to the scarcity of the integral benchmark data. (author)

Study on severe accidents and countermeasures for WWER-1000 reactors using the integral code ASTEC

International Nuclear Information System (INIS)

Tusheva, P.; Schaefer, F.; Altstadt, E.; Kliem, S.; Reinke, N.

2011-01-01

The research field focussing on the investigations and the analyses of severe accidents is an important part of the nuclear safety. To maintain the safety barriers as long as possible and to retain the radioactivity within the airtight premises or the containment, to avoid or mitigate the consequences of such events and to assess the risk, thorough studies are needed. On the one side, it is the aim of the severe accident research to understand the complex phenomena during the in- and ex-vessel phase, involving reactor-physics, thermal-hydraulics, physicochemical and mechanical processes. On the other side the investigations strive for effective severe accident management measures. This paper is focused on the possibilities for accident management measures in case of severe accidents. The reactor pressure vessel is the last barrier to keep the molten materials inside the reactor, and thus to prevent higher loads to the containment. To assess the behaviour of a nuclear power plant during transient or accident conditions, computer codes are widely used, which have to be validated against experiments or benchmarked against other codes. The analyses performed with the integral code ASTEC cover two accident sequences which could lead to a severe accident: a small break loss of coolant accident and a station blackout. The results have shown that in case of unavailability of major active safety systems the reactor pressure vessel would ultimately fail. The discussed issues concern the main phenomena during the early and late in-vessel phase of the accident, the time to core heat-up, the hydrogen production, the mass of corium in the reactor pressure vessel lower plenum and the failure of the reactor pressure vessel. Additionally, possible operator's actions and countermeasures in the preventive or mitigative domain are addressed. The presented investigations contribute to the validation of the European integral severe accidents code ASTEC for WWER-1000 type of reactors

Analyses of SBO sequence of VVER1000 reactor using TRACE and MELCOR codes

International Nuclear Information System (INIS)

Mazzini, Guido; Kyncl, Milos; Miglierini, Bruno; Kopecek, Vit

2015-01-01

In response to the Fukushima accident, the European Commission ordered to perform stress tests to all European Nuclear Power Plants (NPPs). Due to shortage of time a number of conclusions in national stress tests reports were based on engineering judgment only. In the Czech Republic, as a follow up, a consortium of Research Organizations and Universities has decided to simulate selected stress tests scenarios, in particular station Black-Out (SBO) and Loss of Ultimate Sink (LoUS), with the aim to verify conclusions made in the national stress report and to analyse time response of respective source term releases. These activities are carried out in the frame of the project 'Prevention, preparedness and mitigation of consequences of Severe Accident (SA) at Czech NPPs in relation to lessons learned from stress tests after Fukushima' financed by the Ministry of Interior. The Research Centre Rez has been working on the preparation of a MELCOR model for VVER1000 NPP starting with a plant systems nodalization. The basic idea of this paper is to benchmark the MELCOR model with the validated TRACE model, first comparing the steady state and continuing in a long term SBO plus another event until the beginning of the severe accident. The presented work focuses mainly on the preliminary comparison of the thermo-hydraulics of the two models created in MELCOR and TRACE codes. After that, preliminary general results of the SA progression showing the hydrogen production and the relocation phenomena will be shortly discussed. This scenario is considered closed after some seconds to the break of the lower head. (author)

Implication of the cause of differences in 3D structures of proteins with high sequence identity based on analyses of amino acid sequences and 3D structures.

Science.gov (United States)

Matsuoka, Masanari; Sugita, Masatake; Kikuchi, Takeshi

2014-09-18

Proteins that share a high sequence homology while exhibiting drastically different 3D structures are investigated in this study. Recently, artificial proteins related to the sequences of the GA and IgG binding GB domains of human serum albumin have been designed. These artificial proteins, referred to as GA and GB, share 98% amino acid sequence identity but exhibit different 3D structures, namely, a 3α bundle versus a 4β + α structure. Discriminating between their 3D structures based on their amino acid sequences is a very difficult problem. In the present work, in addition to using bioinformatics techniques, an analysis based on inter-residue average distance statistics is used to address this problem. It was hard to distinguish which structure a given sequence would take only with the results of ordinary analyses like BLAST and conservation analyses. However, in addition to these analyses, with the analysis based on the inter-residue average distance statistics and our sequence tendency analysis, we could infer which part would play an important role in its structural formation. The results suggest possible determinants of the different 3D structures for sequences with high sequence identity. The possibility of discriminating between the 3D structures based on the given sequences is also discussed.

Assessment of PASS Effectiveness under Severe Accidents in Nuclear Power Plants

International Nuclear Information System (INIS)

Choi, Yu Jung; Lee, Sung Bok; Kim, Hyeong Taek; Lee, Jin Yong

2008-01-01

Following the accident at Three Mile Island Unit 2 (TMI-2) on March 28, 1979, the USNRC formed a lessons-learned Task Force to identify and evaluate safety concerns originating with the TMI-2 accident. NUREG-0578 documented the results of the task force effort. One of the recommendations of the task force was for licensees to upgrade the capability to obtain samples from the reactor coolant system and containment atmosphere under high radioactivity conditions and to provide the capability for chemical and spectral analyses of high-level samples on site. NUREG-0737 contained the details of the TMI recommendations that were to be implemented by the licensees. Additional criteria for post accident sampling system(PASS) were issued by Regulatory Guide 1.97. As the results, PASS has been installed on nuclear power plants(NPPs) in Korea as well as United States. However, significant improvements have been achieved since the TMI-2 accident in the areas of understanding risks associated with nuclear plant operations and developing better strategies for managing the response to potential severe accidents at NPPs. Thus, the requirements for PASS have been re-evaluated in some reports. According to the reports, the samples and measurements from PASS do not contribute significantly to emergency management response to severe accidents due to the long analyzing time, 3 hours. Hence, this paper focused on the development of the quantitative analysis methodology to analyze the sequence of the severe accident in Yonggwang nuclear power plants (YGN) and presented the results of the analysis according to the developed methodology

The United States Department of Energy (DOE) Computerized Accident/Incident Reporting System (CAIRS)

International Nuclear Information System (INIS)

Briscoe, G.J.

1993-01-01

The Department of Energy's (DOE) Computerized Accident/Incident Reporting System (CAIRS) is a comprehensive data base containing more than 50,000 investigation reports of injury/illness, property damage and vehicle accident cases representing safety data from 1975 to the present for more than 150 DOE contractor organizations. A special feature is that the text of each accident report is translated using a controlled dictionary and rigid sentence structure called Factor Relationship and Sequence of Events (FRASE) that enhances the ability to retrieve specific types of information and to perform detailed analyses. DOE summary and individual contractor reports are prepared quarterly and annually. In addition, ''Safety Performance Profile'' reports for individual organizations are prepared to provide advance information to appraisal teams, and special topical reports are prepared for areas of concern such as an increase in the number of security injuries or environmental releases. The data base is open to all DOE and Contractor registered users with no access restrictions other than that required by the Privacy Act

Analysis of severe accidents in pressurized heavy water reactors

International Nuclear Information System (INIS)

2008-06-01

Certain very low probability plant states that are beyond design basis accident conditions and which may arise owing to multiple failures of safety systems leading to significant core degradation may jeopardize the integrity of many or all the barriers to the release of radioactive material. Such event sequences are called severe accidents. It is required in the IAEA Safety Requirements publication on Safety of the Nuclear Power Plants: Design, that consideration be given to severe accident sequences, using a combination of engineering judgement and probabilistic methods, to determine those sequences for which reasonably practicable preventive or mitigatory measures can be identified. Acceptable measures need not involve the application of conservative engineering practices used in setting and evaluating design basis accidents, but rather should be based on realistic or best estimate assumptions, methods and analytical criteria. Recently, the IAEA developed a Safety Report on Approaches and Tools for Severe Accident Analysis. This publication provides a description of factors important to severe accident analysis, an overview of severe accident phenomena and the current status in their modelling, categorization of available computer codes, and differences in approaches for various applications of severe accident analysis. The report covers both the in- and ex-vessel phases of severe accidents. The publication is consistent with the IAEA Safety Report on Accident Analysis for Nuclear Power Plants and can be considered as a complementary report specifically devoted to the analysis of severe accidents. Although the report does not explicitly differentiate among various reactor types, it has been written essentially on the basis of available knowledge and databases developed for light water reactors. Therefore its application is mostly oriented towards PWRs and BWRs and, to a more limited extent, they can be only used as preliminary guidance for other types of reactors

Severe Accident Sequence Analysis Program: Anticipated transient without scram simulations for Browns Ferry Nuclear Plant Unit 1

International Nuclear Information System (INIS)

Dallman, R.J.; Gottula, R.C.; Holcomb, E.E.; Jouse, W.C.; Wagoner, S.R.; Wheatley, P.D.

1987-05-01

An analysis of five anticipated transients without scram (ATWS) was conducted at the Idaho National Engineering Laboratory (INEL). The five detailed deterministic simulations of postulated ATWS sequences were initiated from a main steamline isolation valve (MSIV) closure. The subject of the analysis was the Browns Ferry Nuclear Plant Unit 1, a boiling water reactor (BWR) of the BWR/4 product line with a Mark I containment. The simulations yielded insights to the possible consequences resulting from a MSIV closure ATWS. An evaluation of the effects of plant safety systems and operator actions on accident progression and mitigation is presented

Causes of Accidents Near Accelerators and Radiation Protection Arrangements; Causes d'accidents aupres des accelerateurs et dispositions de radioprotection

Energy Technology Data Exchange (ETDEWEB)

Joffre, H; Vialettes, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-07-01

The authors present, first, some typical accidents mentioned in bibliography or happened in CEA Research Centers. The accidents are analysed to precise the main cause and get some experience. Then the authors study the interest of a centralized control for security, detection and signalling devices used near every important accelerator. (author) [French] Les auteurs presentent, tout d'abord, quelques accidents typiques rapportes dans la bibliographie ou survenus dans les Centres de Recherches du CEA. Ces accidents sont analyses pour en preciser la cause principale et en degager les enseignements. Enfin les auteurs etudient l'interet d'un controle centralise des dispositifs de securite, de detection et de signalisation mis en oeuvre aupres de tout accelerateur important. (auteur)

Computerized accident management support system: development for severe accident management

International Nuclear Information System (INIS)

Garcia, V.; Saiz, J.; Gomez, C.

1998-01-01

The activities involved in the international Halden Reactor Project (HRP), sponsored by the OECD, include the development of a Computerized Accident Management Support System (CAMS). The system was initially designed for its operation under normal conditions, operational transients and non severe accidents. Its purpose is to detect the plant status, analyzing the future evolution of the sequence (initially using the APROS simulation code) and the possible recovery and mitigation actions in case of an accident occurs. In order to widen the scope of CAMS to severe accident management issues, the integration of the MAAP code in the system has been proposed, as the contribution of the Spanish Electrical Sector to the project (with the coordination of DTN). To include this new capacity in CAMS is necessary to modify the system structure, including two new modules (Diagnosis and Adjustment). These modules are being developed currently for Pressurized Water Reactors and Boiling Water REactors, by the engineering of UNION FENOSA and IBERDROLA companies (respectively). This motion presents the characteristics of the new structure of the CAMS, as well as the general characteristics of the modules, developed by these companies in the framework of the Halden Reactor Project. (Author)

German (GRS) approach to accident analysis (part I). German licensing basis for accident analyses. Applicants accident analyses in second part license for Konvoi-plants. Appendix 1. Assessor accident analyses in second part license for Konvoi-plants. Appendix 2. Reference list of DBA to be considered in the safety status analysis of a PSR. Appendix 3a. Reference list of special very rare and BDB plant conditions to be considered in the safety status analysis of a PSE. Appendix 3b

International Nuclear Information System (INIS)

Velkov, K.

2002-01-01

LOCA analyses.Appendix 3a: Concerns Level 3, accidents and events to be considered for transients, accidents and events to be considered for losses of coolant (LOCA), accidents and radiologically representative events, as well as PWR-specific spreading impacts to be considered as possible initiating events for transients and SBLOCA. These events are defined for PWR and BWR. Appendix 3b: Level 4, PWR- and BWR-specific special, very rare events,(ATWS and site-specific external civil impacts (certain emergencies)), beyond-design-basis plant conditions. These event and accident as in previous Appendix is defined again for PWR and BWR reactor types

Persistence of airline accidents.

Science.gov (United States)

Barros, Carlos Pestana; Faria, Joao Ricardo; Gil-Alana, Luis Alberiko

2010-10-01

This paper expands on air travel accident research by examining the relationship between air travel accidents and airline traffic or volume in the period from 1927-2006. The theoretical model is based on a representative airline company that aims to maximise its profits, and it utilises a fractional integration approach in order to determine whether there is a persistent pattern over time with respect to air accidents and air traffic. Furthermore, the paper analyses how airline accidents are related to traffic using a fractional cointegration approach. It finds that airline accidents are persistent and that a (non-stationary) fractional cointegration relationship exists between total airline accidents and airline passengers, airline miles and airline revenues, with shocks that affect the long-run equilibrium disappearing in the very long term. Moreover, this relation is negative, which might be due to the fact that air travel is becoming safer and there is greater competition in the airline industry. Policy implications are derived for countering accident events, based on competition and regulation. © 2010 The Author(s). Journal compilation © Overseas Development Institute, 2010.

The significance of domino effect in chemical accidents

OpenAIRE

Hemmatian, Behrouz; Abdolhamidzadeh, B; Darbra Roman, Rosa Maria; Casal Fàbrega, Joaquim

2014-01-01

A historical survey was performed on 330 accidents involving domino effect, occurred in process/storage plants and in the transportation of hazardous materials; only accidents occurred after 1st-January-1961 have been considered. The main features – geographical location, type of accident, materials involved, origin and causes, consequences, domino sequences – were analyzed, with special consideration to the situation in the developing countries and compared to those from other previous surve...

Professional experience and traffic accidents/near-miss accidents among truck drivers.

Science.gov (United States)

Girotto, Edmarlon; Andrade, Selma Maffei de; González, Alberto Durán; Mesas, Arthur Eumann

2016-10-01

To investigate the relationship between the time working as a truck driver and the report of involvement in traffic accidents or near-miss accidents. A cross-sectional study was performed with truck drivers transporting products from the Brazilian grain harvest to the Port of Paranaguá, Paraná, Brazil. The drivers were interviewed regarding sociodemographic characteristics, working conditions, behavior in traffic and involvement in accidents or near-miss accidents in the previous 12 months. Subsequently, the participants answered a self-applied questionnaire on substance use. The time of professional experience as drivers was categorized in tertiles. Statistical analyses were performed through the construction of models adjusted by multinomial regression to assess the relationship between the length of experience as a truck driver and the involvement in accidents or near-miss accidents. This study included 665 male drivers with an average age of 42.2 (±11.1) years. Among them, 7.2% and 41.7% of the drivers reported involvement in accidents and near-miss accidents, respectively. In fully adjusted analysis, the 3rd tertile of professional experience (>22years) was shown to be inversely associated with involvement in accidents (odds ratio [OR] 0.29; 95% confidence interval [CI] 0.16-0.52) and near-miss accidents (OR 0.17; 95% CI 0.05-0.53). The 2nd tertile of professional experience (11-22 years) was inversely associated with involvement in accidents (OR 0.63; 95% CI 0.40-0.98). An evident relationship was observed between longer professional experience and a reduction in reporting involvement in accidents and near-miss accidents, regardless of age, substance use, working conditions and behavior in traffic. Copyright © 2016 Elsevier Ltd. All rights reserved.

Accident risks in the energy sector

International Nuclear Information System (INIS)

Burgherr, P.

2005-01-01

This article discusses the accident rate of natural gas installations, which are quoted by the author to be lowest of all fossil fuels. The statistics on accidents and their consequences are looked at for the whole natural gas supply chain. The results of a study commissioned by the Swiss Gas and Water Professionals Association (SVGW) are presented and discussed. Statistics for the European Union and Eastern Europe are looked at and analysed. The study's methodological basis is described and the criteria used for the definition of an accident considered to be 'serious' are listed. The results of comparisons made of various energy chains are presented and discussed. Graphics are presented of frequency of occurrence and seriousness of damage for various forms of energy as well as for maximum possible consequences of accidents. Specific analyses for the natural gas chain are presented

Supplemental analysis of accident sequences and source terms for waste treatment and storage operations and related facilities for the US Department of Energy waste management programmatic environmental impact statement

International Nuclear Information System (INIS)

Folga, S.; Mueller, C.; Nabelssi, B.; Kohout, E.; Mishima, J.

1996-12-01

This report presents supplemental information for the document Analysis of Accident Sequences and Source Terms at Waste Treatment, Storage, and Disposal Facilities for Waste Generated by US Department of Energy Waste Management Operations. Additional technical support information is supplied concerning treatment of transuranic waste by incineration and considering the Alternative Organic Treatment option for low-level mixed waste. The latest respirable airborne release fraction values published by the US Department of Energy for use in accident analysis have been used and are included as Appendix D, where respirable airborne release fraction is defined as the fraction of material exposed to accident stresses that could become airborne as a result of the accident. A set of dominant waste treatment processes and accident scenarios was selected for a screening-process analysis. A subset of results (release source terms) from this analysis is presented

Underreporting of maritime accidents to vessel accident databases.

Science.gov (United States)

Hassel, Martin; Asbjørnslett, Bjørn Egil; Hole, Lars Petter

2011-11-01

Underreporting of maritime accidents is a problem not only for authorities trying to improve maritime safety through legislation, but also to risk management companies and other entities using maritime casualty statistics in risk and accident analysis. This study collected and compared casualty data from 01.01.2005 to 31.12.2009, from IHS Fairplay and the maritime authorities from a set of nations. The data was compared to find common records, and estimation of the true number of occurred accidents was performed using conditional probability given positive dependency between data sources, several variations of the capture-recapture method, calculation of best case scenario assuming perfect reporting, and scaling up a subset of casualty information from a marine insurance statistics database. The estimated upper limit reporting performance for the selected flag states ranged from 14% to 74%, while the corresponding estimated coverage of IHS Fairplay ranges from 4% to 62%. On average the study results document that the number of unreported accidents makes up roughly 50% of all occurred accidents. Even in a best case scenario, only a few flag states come close to perfect reporting (94%). The considerable scope of underreporting uncovered in the study, indicates that users of statistical vessel accident data should assume a certain degree of underreporting, and adjust their analyses accordingly. Whether to use correction factors, a safety margin, or rely on expert judgment, should be decided on a case by case basis. Copyright © 2011 Elsevier Ltd. All rights reserved.

Application of the integral code MELCOR for German NPPs and use within accident management and PSA projects

International Nuclear Information System (INIS)

Sonnenkalb, Martin

2006-01-01

The paper summarizes the application of MELCOR to German NPPS with PWR and BWR. A development of different code systems like ATHLET/ATHLET-CD, COCOSYS and ASTEC is done as well at GRS but it is not discussed in this paper. GRS has been using MELCOR since 1990 for real plant calculations. The results of MELCOR analyses are used mainly in PSA level 2 studies and in Accident Management projects for both types of NPPs. MELCOR has been a very useful and robust tool for these analyses. The calculations performed within the PSA level 2 studies for both types of German NPPs have shown that typical severe accident scenarios are characterized by several phases and that the consideration of plant specifics are important not only for realistic source term calculations. An overview of typically severe accident phases together with main accident management measures installed in German NPPs is presented in the paper. Several severe accident sequences have been calculated for both reactor types and some detailed nodalisation studies and code to code comparisons have been prepared in the past, to prove the developed core, reactor circuit and containment/building nodalisation schemes. Together with the compilation of the MELCOR data set, the qualification of the nodalisation schemes has been pursued with comparative calculations with detailed GRS codes for selected phases of severe accidents. The results of these comparative analyses showed in most of the areas a good agreement of essential parameters and of the general description of the plant behaviour during the accident progression. The in general detail of the German plant nodalisation schemes developed for MELCOR contributes significantly to this good agreement between integral and detailed code results. The implementation of MELCOR into the GRS simulator ATLAS was very important for the assessment of the results, not only due to the great detail of the nodalisation schemes used. It is used for training of severe accident

Advantages for EDF of using and updating PSAs for the probabilistic analysis of accident scenarios in nuclear power plants

International Nuclear Information System (INIS)

Feuillade, Gilles

2000-01-01

This paper shows the advantages for EDF of using and updating PSA models of PWR units for the probabilistic assessment of accident scenarios. These advantages may be classified in various categories: The construction of PSA models makes it possible to aggregate knowledge in a variety of fields: thermohydraulics, the behavior of equipment and systems, organization, plant operation, etc. The updating of PSA models makes it possible to monitor the state of progress of PWR unit safety levels and also allows a variety of applications to be used throughout the service life of the unit. The results obtained are directly applicable to the units as the 'reference PSA models' developed by EDF conform to the units in service. The use of PSA for the examination of incident or accident scenarios makes it possible to verify the adequacy of the resources both in terms of 'systems' and 'plant operation'. These two notions are to be taken in the broadest sense, as they cover the aspects of system design, reliability and availability of equipment, organization of plant operation, comprehensiveness of operating procedures, human redundancy, etc. The use of PSA models through the different applications (analyses of predominant sequences, analyses of main equipment failures, analyses main operator actions, analyses according to the power units, etc) is becoming an indispensable supplement to conventional deterministic analyses of the envisaged accident scenarios. Within the scope of accident prevention, it constitutes a tool to assist the decision-maker, especially when evaluating the pertinence of the General Operating Rules (operating procedures, operating technical specifications, periodic testing, etc). (S.Y.)

Evaluation of the status of science and technology concerning the performance and interpretation of accident analyses using analysis simulators; Ermittlung des Standes von Wissenschaft und Technik bei der Durchfuehrung und Bewertung von Stoerfallanalysen und der Verwendung von Analysesimulatoren

Energy Technology Data Exchange (ETDEWEB)

Pointner, Winfried; Cuesta Morales, Alejandra; Koppers, Vera; Kowalik, Michael; Broecker, Annette; Li, Tianqi; Mayer, Gerhard; Palazzo, Simone; Perin, Yann

2017-03-15

The aim of the project is to develop the methodology to perform short-term accident analyses and to clarify scientific-technical questions concerning the reactor and behavior in case of an accident. For short-term reactions it is necessary to provide appropriate analysis tools data and results for the plant specific behavior (reactor core, cooling circuits, containment) for abnormal operation and accidents (design-based and beyond-design accidents). The qualification of the data base and severe accident analyses is part of the project. The analysis simulators were actualized to the most recent version of ATHLET 3.1A.

Severe Accidents: French Regulatory Practice for Nuclear Power Plants

International Nuclear Information System (INIS)

Colin, M.

1997-01-01

In the framework of a continuous and iterative process, the French Safety Authority asks the utility EDF to implement equipment and procedure modifications on the operating reactors, in order to cope with the most likely Severe Accident sequences. As a result of Probabilistic Safety Assessments published in 1990, important equipment and procedure modifications are being implemented on the French PWRs to improve the safety in shutdown states. The implementation of another set of modifications against some reactivity accident sequences is also in progress. More recently, the Safety Authority expressed specific Severe Accident requirements in terms of instrumentation, equipment qualification, high pressure core melt accidents and hydrogen risk prevention. In that respect, EDF was asked to implement hydrogen recombiners on its reactors. On the other hand, the French Safety authority is involved with its German counterpart in the assessment process of the European Pressurized Water Reactor Project. In consistency with the common recommendations of the Safety Authorities involved, Severe Accident provisions for this reactor are being taken into account at the design stage

Internal event analysis for Laguna Verde Unit 1 Nuclear Power Plant. Accident sequence quantification and results; Analisis de eventos internos para la Unidad 1 de la Central Nucleoelectrica de Laguna Verde. Cuantificacion de secuencias de accidente y resultados

Energy Technology Data Exchange (ETDEWEB)

Huerta B, A; Aguilar T, O; Nunez C, A; Lopez M, R [Comision Nacional de Seguridad Nuclear y Salvaguardias, 03000 Mexico D.F. (Mexico)

1994-07-01

The Level 1 results of Laguna Verde Nuclear Power Plant PRA are presented in the {sup I}nternal Event Analysis for Laguna Verde Unit 1 Nuclear Power Plant, CNSNS-TR 004, in five volumes. The reports are organized as follows: CNSNS-TR 004 Volume 1: Introduction and Methodology. CNSNS-TR4 Volume 2: Initiating Event and Accident Sequences. CNSNS-TR 004 Volume 3: System Analysis. CNSNS-TR 004 Volume 4: Accident Sequence Quantification and Results. CNSNS-TR 005 Volume 5: Appendices A, B and C. This volume presents the development of the dependent failure analysis, the treatment of the support system dependencies, the identification of the shared-components dependencies, and the treatment of the common cause failure. It is also presented the identification of the main human actions considered along with the possible recovery actions included. The development of the data base and the assumptions and limitations in the data base are also described in this volume. The accident sequences quantification process and the resolution of the core vulnerable sequences are presented. In this volume, the source and treatment of uncertainties associated with failure rates, component unavailabilities, initiating event frequencies, and human error probabilities are also presented. Finally, the main results and conclusions for the Internal Event Analysis for Laguna Verde Nuclear Power Plant are presented. The total core damage frequency calculated is 9.03x 10-5 per year for internal events. The most dominant accident sequences found are the transients involving the loss of offsite power, the station blackout accidents, and the anticipated transients without SCRAM (ATWS). (Author)

Consequence analysis of core damage states following severe accidents for the CANDU reactor design

International Nuclear Information System (INIS)

Wahba, N.N.; Kim, Y.T.; Lie, S.G.

1997-01-01

The analytical methodology used to evaluate severe accident sequences is described. The relevant thermal-mechanical phenomena and the mathematical approach used in calculating the timing of the accident progression and source term estimate are summarized. The postulated sever accidents analyzed, in general, mainly differ in the timing to reach and progress through each defined c ore damage state . This paper presents the methodology and results of the timing and steam discharge calculations as well as source term estimate out of containment for accident sequences classified as potentially leading to core disassembly following a small break loss-of-coolant accident (LOCA) scenario as a specific example. (author)

Molecular systematics of Indian Alysicarpus (Fabaceae) based on analyses of nuclear ribosomal DNA sequences.

Science.gov (United States)

Gholami, Akram; Subramaniam, Shweta; Geeta, R; Pandey, Arun K

2017-06-01

Alysicarpus Necker ex Desvaux (Fabaceae, Desmodieae) consists of ~30 species that are distributed in tropical and subtropical regions of theworld. In India, the genus is represented by ca. 18 species, ofwhich seven are endemic. Sequences of the nuclear Internal transcribed spacer from38 accessions representing 16 Indian specieswere subjected to phylogenetic analyses. The ITS sequence data strongly support the monophyly of the genus Alysicarpus. Analyses revealed four major well-supported clades within Alysicarpus. Ancestral state reconstructions were done for two morphological characters, namely calyx length in relation to pod (macrocalyx and microcalyx) and pod surface ornamentation (transversely rugose and nonrugose). The present study is the first report on molecular systematics of Indian Alysicarpus.

Sequence and expression analyses of porcine ISG15 and ISG43 genes.

Science.gov (United States)

Huang, Jiangnan; Zhao, Shuhong; Zhu, Mengjin; Wu, Zhenfang; Yu, Mei

2009-08-01

The coding sequences of porcine interferon-stimulated gene 15 (ISG15) and the interferon-stimulated gene (ISG43) were cloned from swine spleen mRNA. The amino acid sequences deduced from porcine ISG15 and ISG43 genes coding sequence shared 24-75% and 29-83% similarity with ISG15s and ISG43s from other vertebrates, respectively. Structural analyses revealed that porcine ISG15 comprises two ubiquitin homologues motifs (UBQ) domain and a conserved C-terminal LRLRGG conjugating motif. Porcine ISG43 contains an ubiquitin-processing proteases-like domain. Phylogenetic analyses showed that porcine ISG15 and ISG43 were mostly related to rat ISG15 and cattle ISG43, respectively. Using quantitative real-time PCR assay, significant increased expression levels of porcine ISG15 and ISG43 genes were detected in porcine kidney endothelial cells (PK15) cells treated with poly I:C. We also observed the enhanced mRNA expression of three members of dsRNA pattern-recognition receptors (PRR), TLR3, DDX58 and IFIH1, which have been reported to act as critical receptors in inducing the mRNA expression of ISG15 and ISG43 genes. However, we did not detect any induced mRNA expression of IFNalpha and IFNbeta, suggesting that transcriptional activations of ISG15 and ISG43 were mediated through IFN-independent signaling pathway in the poly I:C treated PK15 cells. Association analyses in a Landrace pig population revealed that ISG15 c.347T>C (BstUI) polymorphism and the ISG43 c.953T>G (BccI) polymorphism were significantly associated with hematological parameters and immune-related traits.

Restructuring of an Event Tree for a Loss of Coolant Accident in a PSA model

International Nuclear Information System (INIS)

Lim, Ho-Gon; Han, Sang-Hoon; Park, Jin-Hee; Jang, Seong-Chul

2015-01-01

Conventional risk model using PSA (probabilistic Safety Assessment) for a NPP considers two types of accident initiators for internal events, LOCA (Loss of Coolant Accident) and transient event such as Loss of electric power, Loss of cooling, and so on. Traditionally, a LOCA is divided into three initiating event (IE) categories depending on the break size, small, medium, and large LOCA. In each IE group, safety functions or systems modeled in the accident sequences are considered to be applicable regardless of the break size. However, since the safety system or functions are not designed based on a break size, there exist lots of mismatch between safety system/function and an IE, which may make the risk model conservative or in some case optimistic. Present paper proposes new methodology for accident sequence analysis for LOCA. We suggest an integrated single ET construction for LOCA by incorporating a safety system/function and its applicable break spectrum into the ET. Integrated accident sequence analysis in terms of ET for LOCA was proposed in the present paper. Safety function/system can be properly assigned if its applicable range is given by break set point. Also, using simple Boolean algebra with the subset of the break spectrum, final accident sequences are expressed properly in terms of the Boolean multiplication, the occurrence frequency and the success/failure of safety system. The accident sequence results show that the accident sequence is described more detailed compared with the conventional results. Unfortunately, the quantitative results in terms of MCS (minimal Cut-Set) was not given because system fault tree was not constructed for this analysis and the break set points for all 7 point were not given as a specified numerical quantity. Further study may be needed to fix the break set point and to develop system fault tree

Restructuring of an Event Tree for a Loss of Coolant Accident in a PSA model

Energy Technology Data Exchange (ETDEWEB)

Lim, Ho-Gon; Han, Sang-Hoon; Park, Jin-Hee; Jang, Seong-Chul [KAERI, Daejeon (Korea, Republic of)

2015-05-15

Conventional risk model using PSA (probabilistic Safety Assessment) for a NPP considers two types of accident initiators for internal events, LOCA (Loss of Coolant Accident) and transient event such as Loss of electric power, Loss of cooling, and so on. Traditionally, a LOCA is divided into three initiating event (IE) categories depending on the break size, small, medium, and large LOCA. In each IE group, safety functions or systems modeled in the accident sequences are considered to be applicable regardless of the break size. However, since the safety system or functions are not designed based on a break size, there exist lots of mismatch between safety system/function and an IE, which may make the risk model conservative or in some case optimistic. Present paper proposes new methodology for accident sequence analysis for LOCA. We suggest an integrated single ET construction for LOCA by incorporating a safety system/function and its applicable break spectrum into the ET. Integrated accident sequence analysis in terms of ET for LOCA was proposed in the present paper. Safety function/system can be properly assigned if its applicable range is given by break set point. Also, using simple Boolean algebra with the subset of the break spectrum, final accident sequences are expressed properly in terms of the Boolean multiplication, the occurrence frequency and the success/failure of safety system. The accident sequence results show that the accident sequence is described more detailed compared with the conventional results. Unfortunately, the quantitative results in terms of MCS (minimal Cut-Set) was not given because system fault tree was not constructed for this analysis and the break set points for all 7 point were not given as a specified numerical quantity. Further study may be needed to fix the break set point and to develop system fault tree.

Severe accident source term reassessment

International Nuclear Information System (INIS)

Hazzan, M.J.; Gardner, R.; Warman, E.A.; Jacobs, S.B.

1987-01-01

This paper summarizes the status of the reassessment of severe reactor accident source terms, which are defined as the quantity, type, and timing of fission product releases from such accidents. Concentration is on the major results and conclusions of analyses with modern methods for both pressurized water reactors (PWRs) and boiling water reactors (BWRs), and the special case of containment bypass. Some distinctions are drawn between analyses for PWRs and BWRs. In general, the more the matter is examined, the consequences, or probability of serious consequences, seem to be less. (author)

Risk assessment of severe accident-induced steam generator tube rupture

International Nuclear Information System (INIS)

1998-03-01

This report describes the basis, results, and related risk implications of an analysis performed by an ad hoc working group of the U.S. Nuclear Regulatory Commission (NRC) to assess the containment bypass potential attributable to steam generator tube rupture (SGTR) induced by severe accident conditions. The SGTR Severe Accident Working Group, comprised of staff members from the NRC's Offices of Nuclear Reactor Regulation (NRR) and Nuclear Regulatory Research (RES), undertook the analysis beginning in December 1995 to support a proposed steam generator integrity rule. The work drew upon previous risk and thermal-hydraulic analyses of core damage sequences, with a focus on the Surry plant as a representative example. This analysis yielded new results, however, derived by predicting thermal-hydraulic conditions of selected severe accident scenarios using the SCDAP/RELAP5 computer code, flawed tube failure modeling, and tube failure probability estimates. These results, in terms of containment bypass probability, form the basis for the findings presented in this report. The representative calculation using Surry plant data indicates that some existing plants could be vulnerable to containment bypass resulting from tube failure during severe accidents. To specifically identify the population of plants that may pose a significant bypass risk would require more definitive analysis considering uncertainties in some assumptions and plant- and design-specific variables. 46 refs., 62 figs., 37 tabs

An estimation of the accident sequence of the LOCA groups for the PSA model of the KSNP

International Nuclear Information System (INIS)

Han, Seok Jung; Yang, Joon Eon

2004-01-01

A new trend of the probabilistic safety assessment (PSA) technology is to improve and enhance the current PSA model to be adequate for risk-informed applications (RIA). Requirements of a PSA model for the RIA are summarized as (1) reduction of the conservatism in the model utilizing all available information and (2) consideration of the specific features of a plant as designed, as operated. This is because the PSA based on conservatism and insufficient consideration of the plant-specific features resulted in a shadow effect on the assessment results. When a PSA model is used in a risk-informed application, more precise risk-information is more helpful to decision making process, so the reduction of the conservatism and the consideration of the plant-specific features in a PSA model are the most essential elements. Recently, an effort has been performed to modify the current PSA model for the Korea Standard Nuclear Power plant (KSNP) to be used in risk-informed applications. A re-estimation of the accident sequence of the loss of coolant accident (LOCA) groups for the PSA model of the KSNP has been performed

The 1986 Chernobyl accident; Der Unfall von Tschernobyl 1986

Energy Technology Data Exchange (ETDEWEB)

Kerner, Alexander; Stueck, Reinhard; Weiss, Frank-Peter [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, Garching bei Muenchen, Koeln (Germany). Bereich Reaktorsicherheitsanalysen; Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, Koeln (Germany)

2011-02-15

April 26, 2011 marks the 25th anniversary of the Chernobyl reactor accident, the worst incident in the history of the peaceful utilization of nuclear power. While investigations of the course of events and the causes of the accident largely present a uniform picture, descriptions still vary widely when it comes to the impact on the population and the environment. This treatment of the Chernobyl accident constitutes a summary of facts about the initiation of the accident and the sequence of events that followed. In addition, measures are described which were taken to exclude any repetition of a disaster of this kind. The health consequences and the socio-economic impact of the accident are not discussed in any detail. The first section contains an introduction and an overview of the Soviet RBMK (Chernobyl) reactor line. In section 2, fundamental characteristics of this special type of reactor, which was exclusively built in the former Soviet Union, are discussed. This information is necessary to understand the sequence of accident events and provides an answer to the frequent question whether that accident could be transferred to reactors in this country. The third section outlines the history of the accident caused ultimately by a commissioning test never performed before. The section is completed by a brief description of radiological releases and the state of the plant after the accident when entombed in the ''sarcophagus.'' The different causes are then summarized and the modifications afterwards made to RBMK reactors are outlined. (orig.)

Loss of Flow Accident (LOFA) analyses using LabView-based NRR simulator

Energy Technology Data Exchange (ETDEWEB)

Arafa, Amany Abdel Aziz; Saleh, Hassan Ibrahim [Atomic Energy Authority, Cairo (Egypt). Radiation Engineering Dept.; Ashoub, Nagieb [Atomic Energy Authority, Cairo (Egypt). Reactor Physics Dept.

2016-12-15

This paper presents a generic Loss of Flow Accident (LOFA) scenario module which is integrated in the LabView-based simulator to imitate a Nuclear Research Reactor (NRR) behavior for different user defined LOFA scenarios. It also provides analyses of a LOFA of a single fuel channel and its impact on operational transactions and on the behavior of the reactor. The generic LOFA scenario module includes graphs needed to clarify the effects of the LOFA under study. Furthermore, the percentage of the loss of mass flow rate, the mode of flow reduction and the start time and transient time of LOFA are user defined to add flexibility to the LOFA scenarios. The objective of integrating such generic LOFA module is to be able to deal with such incidents and avoid their significant effects. It is also useful in the development of expertise in this area and reducing the operator training and simulations costs. The results of the implemented generic LOFA module agree well with that of COBRA-IIIC code and the earlier guidebook for this series of transients.

Socioeconomic consequences of nuclear reactor accidents

International Nuclear Information System (INIS)

Tawil, J.J.; Callaway, J.W.; Coles, B.L.; Cronin, F.J.; Currie, J.W.; Imhoff, K.L.; Lewis, P.M.; Nesse, R.J.; Strenge, D.L.

1984-06-01

This report identifies and characterizes the off-site socioeconomic consequences that would likely result from a severe radiological accident at a nuclear power plant. The types of impacts that are addressed include economic impacts, health impacts, social/psychological impacts and institutional impacts. These impacts are identified for each of several phases of a reactor accident - from the warning phase through the post-resettlement phase. The relative importance of the impact during each accident phase and the degree to which the impact can be predicted are indicated. The report also examines the methods that are currently used for assessing nuclear reactor accidents, including development of accident scenarios and the estimating of socioeconomic accident consequences with various models. Finally, a critical evaluation is made regarding the use of impact analyses in estimating the contribution of socioeconomic consequences to nuclear accident reactor accident risk. 116 references, 7 figures, 15 tables

Learning lessons from Natech accidents - the eNATECH accident database

Science.gov (United States)

Krausmann, Elisabeth; Girgin, Serkan

2016-04-01

When natural hazards impact industrial facilities that house or process hazardous materials, fires, explosions and toxic releases can occur. This type of accident is commonly referred to as Natech accident. In order to prevent the recurrence of accidents or to better mitigate their consequences, lessons-learned type studies using available accident data are usually carried out. Through post-accident analysis, conclusions can be drawn on the most common damage and failure modes and hazmat release paths, particularly vulnerable storage and process equipment, and the hazardous materials most commonly involved in these types of accidents. These analyses also lend themselves to identifying technical and organisational risk-reduction measures that require improvement or are missing. Industrial accident databases are commonly used for retrieving sets of Natech accident case histories for further analysis. These databases contain accident data from the open literature, government authorities or in-company sources. The quality of reported information is not uniform and exhibits different levels of detail and accuracy. This is due to the difficulty of finding qualified information sources, especially in situations where accident reporting by the industry or by authorities is not compulsory, e.g. when spill quantities are below the reporting threshold. Data collection has then to rely on voluntary record keeping often by non-experts. The level of detail is particularly non-uniform for Natech accident data depending on whether the consequences of the Natech event were major or minor, and whether comprehensive information was available for reporting. In addition to the reporting bias towards high-consequence events, industrial accident databases frequently lack information on the severity of the triggering natural hazard, as well as on failure modes that led to the hazmat release. This makes it difficult to reconstruct the dynamics of the accident and renders the development of

A Study on the Operation Strategy for Combined Accident including TLOFW accident

International Nuclear Information System (INIS)

Kim, Bo Gyung; Kang, Gook Young; Yoon, Ho Joon

2014-01-01

It is difficult for operators to recognize the necessity of a feed-and-bleed (F-B) operation when the loss of coolant accident and failure of secondary side occur. An F-B operation directly cools down the reactor coolant system (RCS) using the primary cooling system when residual heat removal by the secondary cooling system is not available. The plant is not always necessary the F-B operation when the secondary side is failed. It is not necessary to initiate an F-B operation in the case of a medium or large break because these cases correspond to low RCS pressure sequences when the secondary side is failed. If the break size is too small to sufficiently decrease the RCS pressure, the F-B operation is necessary. Therefore, in the case of a combined accident including a secondary cooling system failure, the provision of clear information will play a critical role in the operators' decision to initiate an F-B operation. This study focuses on the how we establish the operation strategy for combined accident including the failure of secondary side in consideration of plant and operating conditions. Previous studies have usually focused on accidents involving a TLOFW accident. The plant conditions to make the operators confused seriously are usually the combined accident because the ORP only focuses on a single accident and FRP is less familiar with operators. The relationship between CET and PCT under various plant conditions is important to decide the limitation of initiating the F-B operation to prevent core damage

Thermalydraulic processes in the reactor coolant system of a BWR under severe accident conditions

International Nuclear Information System (INIS)

Hodge, S.A.

1990-01-01

Boiling water reactors (BWRs) incorporate many unique structural features that make their expected response under severe accident conditions very different from that predicted in the case of pressurized water reactor accident sequences. Automatic main steam isolation valve (MIV) closure as the vessel water level approaches the top of the core would cause reactor vessel isolation while automatic recirculation pump trip would limit the in-vessel flows to those characteristic of natural circulation (as disturbed by vessel relief valve actuation). This paper provides a discussion of the BWR control blade, channel box, core plate, control rod guide tube, and reactor vessel safety relief valve (SRV) configuration and the effects of these structural components upon thermal hydraulic processes within the reactor vessel under severe accident conditions. The dominant BWR severe accident sequences as determined by probabilistic risk assessment are described and the expected timing of events for the unmitigated short-term station blackout severe accident sequence at the Peach Bottom atomic power station is presented

Performance of metal and oxide fuels during accidents in a large liquid metal cooled reactor

International Nuclear Information System (INIS)

Cahalan, J.; Wigeland, R.; Friedel, G.; Kussmaul, G.; Royl, P.; Moreau, J.; Perks, M.

1990-01-01

In a cooperative effort among European and US analysts, an assessment of the comparative safety performance of metal and oxide fuels during accidents in a large (3500 MWt), pool-type, liquid-metal-cooled reactor (LMR) was performed. The study focused on three accident initiators with failure to scram: the unprotected loss-of-flow (ULOF), the unprotected transient overpower (UTOP), and the unprotected loss-of-heat-sink (ULOHS). Emphasis was placed on identification of design features that provide passive, self-limiting responses to upset conditions, and quantification of relative safety margins. The analyses show that in ULOF and ULOHS sequences, metal-fueled LMRs with pool-type primary systems provide larger temperature margins to coolant boiling than oxide-fueled reactors of the same design. 3 refs., 4 figs

Analysis of unmitigated large break loss of coolant accidents using MELCOR code

Science.gov (United States)

Pescarini, M.; Mascari, F.; Mostacci, D.; De Rosa, F.; Lombardo, C.; Giannetti, F.

2017-11-01

In the framework of severe accident research activity developed by ENEA, a MELCOR nodalization of a generic Pressurized Water Reactor of 900 MWe has been developed. The aim of this paper is to present the analysis of MELCOR code calculations concerning two independent unmitigated large break loss of coolant accident transients, occurring in the cited type of reactor. In particular, the analysis and comparison between the transients initiated by an unmitigated double-ended cold leg rupture and an unmitigated double-ended hot leg rupture in the loop 1 of the primary cooling system is presented herein. This activity has been performed focusing specifically on the in-vessel phenomenology that characterizes this kind of accidents. The analysis of the thermal-hydraulic transient phenomena and the core degradation phenomena is therefore here presented. The analysis of the calculated data shows the capability of the code to reproduce the phenomena typical of these transients and permits their phenomenological study. A first sequence of main events is here presented and shows that the cold leg break transient results faster than the hot leg break transient because of the position of the break. Further analyses are in progress to quantitatively assess the results of the code nodalization for accident management strategy definition and fission product source term evaluation.

Iodine behaviour in severe accidents

Energy Technology Data Exchange (ETDEWEB)

Dutton, L M.C.; Grindon, E; Handy, B J; Sutherland, L [NNC Ltd., Knutsford (United Kingdom); Bruns, W G; Sims, H E [AEA Technology, Harwell (United Kingdom); Dickinson, S [AEA Technology, Winfrith (United Kingdom); Hueber, C; Jacquemain, D [IPSN/CEA, Cadarache, Saint Paul-Lez-Durance (France)

1996-12-01

A description is given of analyses which identify which aspects of the modelling and data are most important in evaluating the release of radioactive iodine to the environment following a potential severe accident at a PWR and which identify the major uncertainties which affect that release. Three iodine codes are used namely INSPECT, IODE and IMPAIR, and their predictions are compared with those of the PSA code MAAP. INSPECT is a mechanistic code which models iodine behaviour in the aqueous aerosol, spray water and sump water, and the partitioning of volatile species between the aqueous phases and containment gas space. Organic iodine is not modelled. IODE and IMPAIR are semi-empirical codes which do not model iodine behaviour in the aqueous aerosol, but model organic iodine. The fault sequences addressed are based on analyses for the Sizewell `B` design. Two types of sequence have been analysed.: (a) those in which a major release of fission products from the primary circuit to the containment occur, e.g. a large LOCAS, (b) those where the release by-passes the containment, e.g. a leak into the auxiliary building. In the analysis of the LOCA sequences where the pH of the sump is controlled to be a value of 8 or greater, all three codes predict that the oxidation of iodine to produce gas phase species does not make a significant contribution to the source term due to leakage from the reactor building and that the latter is dominated by iodide in the aerosol. In the case where the pH of the sump is not controlled, it is found that the proportion of gas phase iodine increases significantly, although the cumulative leakage predicted by all three codes is not significantly different from that predicted by MAAP. The radiolytic production of nitric acid could be a major factor in determining the pH, and if the pH were reduced, the codes predict an increase in gas phase iodine species leaked from the containment. (author) 4 figs., 7 tabs., 13 refs.

The role of systems availability and operator actions in accident management

International Nuclear Information System (INIS)

Lutz, R.J. Jr.; Scobel, J.H.

1988-01-01

Traditional analyses of severe accidents, such as those presented in Probabilistic Risk Assessment (PRA) studies of nuclear power stations, have generally been performed on the assumption that all means of cooling the reactor core are lost and that no operator actions to mitigate the consequences or progression of the severe accident are performed. The assumption to neglect the availability of safety systems and operator actions which do not prevent core melting can lead to erroneous conclusions regarding the plant severe accident profile. Recent work in severe accident management has identified the need to perform analyses which consider all systems availabilities and operator actions, irrespective of their contribution to the prevention of core melting. These new analyses have far reaching conclusions. The analysis results indicate an unacceptably high degree of simplicity in the present severe accident analyses for Probabilistic Risk Assessment studies; the simplicity is in the assumption that systems availabilities and operator actions which do not impact core melt frequency can be neglected in the severe accident analyses. This results in overly pessimistic predictions of the time of core melting and the subsequent potential for recovery of core cooling prior to core melting. This simplicity can have a considerable impact on severe accident decision making, particularly in the evaluation of alternate plant design features and the priorities for research studies

Accident Analyses for Conversion of the University of Missouri Research Reactor (MURR) from Highly-Enriched to Low-Enriched Uranium

Energy Technology Data Exchange (ETDEWEB)

Stillman, J. A. [Argonne National Lab. (ANL), Argonne, IL (United States); Feldman, E. E. [Argonne National Lab. (ANL), Argonne, IL (United States); Jaluvka, D. [Argonne National Lab. (ANL), Argonne, IL (United States); Wilson, E. H. [Argonne National Lab. (ANL), Argonne, IL (United States); Foyto, L. P. [Univ. of Missouri, Columbia, MO (United States); Kutikkad, K. [Univ. of Missouri, Columbia, MO (United States); McKibben, J. C. [Univ. of Missouri, Columbia, MO (United States); Peters, N. J. [Univ. of Missouri, Columbia, MO (United States)

2017-02-01

This report contains the results of reactor accident analyses for the University of Missouri Research Reactor (MURR). The calculations were performed as part of the conversion from the use of highly-enriched uranium (HEU) fuel to the use of low-enriched uranium (LEU) fuel. The analyses were performed by staff members in the Research and Test Reactor Department at the Argonne National Laboratory (ANL) and the MURR Facility. MURR LEU conversion is part of an overall effort to develop and qualify high-density fuel within the U.S. High Performance Research Reactor Conversion (USHPRR) program conducted by the U.S. Department of Energy National Nuclear Security Administration’s Office of Material Management and Minimization (M³).

A study on the implementation effect of accident management strategies on safety

International Nuclear Information System (INIS)

Jae, Moo Sung; Kim, Dong Ha; Jin, Young Ho

1996-01-01

This paper presents a new approach for assessing accident management strategies using containment event trees(CETs) developed during an individual plant examination (IPE) for a reference plant (CE type, 950 MWe PWR). Various accident management strategies to reduce risk have been proposed through IPE. Three strategies for the station blackout sequence are used as an example: 1) reactor cavity flooding only, 2) primary system depressurization only, and 3) doing both. These strategies are assumed to be initiated at about the time of core uncovery. The station blackout (SBO) sequence is selected in this paper since it is identified as one of the most threatening sequences to safety of the reference plant. The effectiveness and adverse effects of each accident management strategy are considered synthetically in the CETs. A best estimate assessment for the developed CETs using data obtained from NUREG-1150, other PRA results, and the MAAP code calculations is performed. The strategies are ranked with respect to minimizing the frequencies of various containment failure modes. The proposed approach is demonstrated to be very flexible in that it can be applied to any kind of accident management strategy for any sequence. 9 refs., 3 figs., 2 tabs. (author)

Accidents and transients analyses of a super fast reactor with single flow pass core

International Nuclear Information System (INIS)

Sutanto,; Oka, Yoshiaki

2014-01-01

Highlights: • Safety analysis of a Super FR with single flow pass core is conducted. • Loss of feed water flow leads to a direct effect on the loss of fuel channel flow. • The core pressure is sensitive to LOCA accidents due to the direct effect. • Small LOCA introduces a critical break. • The safety criteria for all selected events are satisfied. - Abstract: The supercritical water cooled fast reactor with single flow pass core has been designed to simplify refueling and the structures of upper and lower mixing plenums. To evaluate the safety performance, safety analysis has been conducted with regard to LOCA and non-LOCA accidents including transient events. Safety analysis results show that the safety criteria are satisfied for all selected events. The total loss of feed water flow is the most important accident which the maximum cladding surface temperature (MCST) is high due to a direct effect of the accident on the total loss of flow in all fuel assemblies. However, actuation of the ADS can mitigate the accident. Small LOCA also introduces a critical break at 7.8% break which results high MCST at BOC because the scram and ADS are not actuated. Early ADS actuation is effective to mitigate the accident. In large LOCA, 100% break LOCA results a high MCST of flooding phase at BOC due to high power peaking at the bottom part. Use of high injection flow rate by 2 LPCI units is effective to decrease the MCST

Accident Source Terms for Pressurized Water Reactors with High-Burnup Cores Calculated using MELCOR 1.8.5.

Energy Technology Data Exchange (ETDEWEB)

Gauntt, Randall O.; Goldmann, Andrew; Kalinich, Donald A.; Powers, Dana A.

2016-12-01

In this study, risk-significant pressurized-water reactor severe accident sequences are examined using MELCOR 1.8.5 to explore the range of fission product releases to the reactor containment building. Advances in the understanding of fission product release and transport behavior and severe accident progression are used to render best estimate analyses of selected accident sequences. Particular emphasis is placed on estimating the effects of high fuel burnup in contrast with low burnup on fission product releases to the containment. Supporting this emphasis, recent data available on fission product release from high-burnup (HBU) fuel from the French VERCOR project are used in this study. The results of these analyses are treated as samples from a population of accident sequences in order to employ approximate order statistics characterization of the results. These trends and tendencies are then compared to the NUREG-1465 alternative source term prescription used today for regulatory applications. In general, greater differences are observed between the state-of-the-art calculations for either HBU or low-burnup (LBU) fuel and the NUREG-1465 containment release fractions than exist between HBU and LBU release fractions. Current analyses suggest that retention of fission products within the vessel and the reactor coolant system (RCS) are greater than contemplated in the NUREG-1465 prescription, and that, overall, release fractions to the containment are therefore lower across the board in the present analyses than suggested in NUREG-1465. The decreased volatility of Cs 2 MoO 4 compared to CsI or CsOH increases the predicted RCS retention of cesium, and as a result, cesium and iodine do not follow identical behaviors with respect to distribution among vessel, RCS, and containment. With respect to the regulatory alternative source term, greater differences are observed between the NUREG-1465 prescription and both HBU and LBU predictions than exist between HBU and LBU

Anthropotechnological analysis of industrial accidents in Brazil.

Science.gov (United States)

Binder, M. C.; de Almeida, I. M.; Monteau, M.

1999-01-01

The Brazilian Ministry of Labour has been attempting to modify the norms used to analyse industrial accidents in the country. For this purpose, in 1994 it tried to make compulsory use of the causal tree approach to accident analysis, an approach developed in France during the 1970s, without having previously determined whether it is suitable for use under the industrial safety conditions that prevail in most Brazilian firms. In addition, opposition from Brazilian employers has blocked the proposed changes to the norms. The present study employed anthropotechnology to analyse experimental application of the causal tree method to work-related accidents in industrial firms in the region of Botucatu, São Paulo. Three work-related accidents were examined in three industrial firms representative of local, national and multinational companies. On the basis of the accidents analysed in this study, the rationale for the use of the causal tree method in Brazil can be summarized for each type of firm as follows: the method is redundant if there is a predominance of the type of risk whose elimination or neutralization requires adoption of conventional industrial safety measures (firm representative of local enterprises); the method is worth while if the company's specific technical risks have already largely been eliminated (firm representative of national enterprises); and the method is particularly appropriate if the firm has a good safety record and the causes of accidents are primarily related to industrial organization and management (multinational enterprise). PMID:10680249

Optimization of the Severe Accident Management Strategy for Domestic Plants and Validation Experiments

International Nuclear Information System (INIS)

Kim, S. B.; Kim, H. D.; Koo, K. M.; Park, R. J.; Hong, S. H.; Cho, Y. R.; Kim, J. T.; Ha, K. S.; Kang, K. H.

2007-04-01

nuclear power plants, a technical basis report and computational aid tools were developed in parallel with the experimental and analytical works for the resolution of the uncertain safety issues. ELIAS experiments were carried out to quantify the boiling heat removal rate at the upper surface of a metallic layer for precise evaluations on the effect of a late in-vessel coolant injection. T-HERMES experiments were performed to examine the two-phase natural circulation phenomena through the gap between the reactor vessel and the insulator in the APR1400. Detailed analyses on the hydrogen control in the APR1400 containment were performed focused on the effect of spray system actuation on the hydrogen burning and the evaluation of the hydrogen behavior in the IRWST. To develop the technical basis report for the severe accident management, analyses using SCDAP/RELAP5 code were performed for the accident sequences of the OPR1000. Based on the experimental and analytical results performed in this study, the computational aids for the evaluations of hydrogen flammability in the containment, criteria of the in-vessel corium cooling, criteria of the external reactor vessel cooling were developed. An ASSA code was developed to validate the signal from the instrumentations during the severe accidents and to process the abnormal signal. Since ASSA can perform the signal processing from the direct input of the nuclear power plant during the severe accident, it can be platform of the computational aids. In this study, the ASSA was linked with the computaional aids for the hydrogen flammability

Optimization of the Severe Accident Management Strategy for Domestic Plants and Validation Experiments

Energy Technology Data Exchange (ETDEWEB)

Kim, S. B.; Kim, H. D.; Koo, K. M.; Park, R. J.; Hong, S. H.; Cho, Y. R.; Kim, J. T.; Ha, K. S.; Kang, K. H

2007-04-15

nuclear power plants, a technical basis report and computational aid tools were developed in parallel with the experimental and analytical works for the resolution of the uncertain safety issues. ELIAS experiments were carried out to quantify the boiling heat removal rate at the upper surface of a metallic layer for precise evaluations on the effect of a late in-vessel coolant injection. T-HERMES experiments were performed to examine the two-phase natural circulation phenomena through the gap between the reactor vessel and the insulator in the APR1400. Detailed analyses on the hydrogen control in the APR1400 containment were performed focused on the effect of spray system actuation on the hydrogen burning and the evaluation of the hydrogen behavior in the IRWST. To develop the technical basis report for the severe accident management, analyses using SCDAP/RELAP5 code were performed for the accident sequences of the OPR1000. Based on the experimental and analytical results performed in this study, the computational aids for the evaluations of hydrogen flammability in the containment, criteria of the in-vessel corium cooling, criteria of the external reactor vessel cooling were developed. An ASSA code was developed to validate the signal from the instrumentations during the severe accidents and to process the abnormal signal. Since ASSA can perform the signal processing from the direct input of the nuclear power plant during the severe accident, it can be platform of the computational aids. In this study, the ASSA was linked with the computaional aids for the hydrogen flammability.

JAERI's activities in JCO accident

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The Japan Atomic Energy Research Institute (JAERI) was actively involved in a variety of technical supports and cooperative activities, such as advice on terminating the criticality condition, contamination checks of the residents and consultation services for the residents, as emergency response actions to the criticality accident at the uranium processing facility operated by the JCO Co. Ltd., which occurred on September 30, 1999. These activities were carried out in collaborative ways by the JAERI staff from the Tokai Research Establishment, Naka Fusion Research Establishment, Oarai Research Establishment, and Headquarter Office in Tokyo. As well, the JAERI was engaged in the post-accident activities such as identification of accident causes, analyses of the criticality accident, and dose assessment of exposed residents, to support the Headquarter for Accident Countermeasures of the Science and Technology Agency (STA), the Accident Investigation Committee and the Health Control Committee of the Nuclear Safety Commission of Japan (NSC). This report compiles the activities, that the JAERI has conducted to date, including the discussions on measures for terminating the criticality condition, evaluation of the fission number, radiation monitoring in the environment, dose assessment, analyses of criticality dynamics. (author)

Accidents - Chernobyl accident; Accidents - accident de Tchernobyl

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

Method of assessing severe accident management strategies

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.; Okrent, D.; Jae, M.; Lim, H.; Milici, T.; Park, H.; Swider, J.; Xing, L.; Yu, D.

1991-01-01

Accident management can be defined as the innovative use of existing and or alternative resources, systems, and actions to prevent or mitigate a severe accident. A significant number of probabilistic safety assessments (PSAs) have been completed that yield the principal plant vulnerabilities. These vulnerabilities can be categorized as (1) dominant sequences with respect to core-melt frequency. (2) dominant sequences with respect to various risk measures. (3) dominant threats that challenge safety functions. (4) dominant threats with respect to failure of safety systems. For each sequence/threat and each combination of strategy, there may be several options available to the operator. Each strategy/option involves phenomenological and operational considerations regarding uncertainty. These considerations include uncertainties in key phenomena, operator behavior, system availability and behavior, and available information. This paper presents a methodology for assessing severe accident management strategies given the key uncertainties delineated at two workshops held at the University of California, Los Angeles. Based on decision trees and influence diagrams, the methodology is currently being applied to two case studies: cavity flooding in a pressurized water reactor (PWR) to prevent vessel penetration or failure, and drywell flooding in a boiling water reactor to prevent vessel and/or containment failure

Role of BWR secondary containments in severe accident mitigation: issues and insights from recent analyses

International Nuclear Information System (INIS)

Greene, S.R.

1988-01-01

All commercial boiling water reactor (BWR) plants in the US employ primary containments of the pressure suppression design. These primary containments are surrounded and enclosed by a secondary containment consisting of a reactor building and refueling bay (MK I and MK II designs), a shield building, auxiliary building and fuel building (MK III), or an auxiliary building and enclosure building (Grand Gulf style MK III). Although secondary containment designs are highly plant specific, their purpose is to minimize the ground level release of radioactive material for a spectrum of traditional design basis accidents. While not designed for severe accident mitigation, these secondary containments might also reduce the radiological consequences of severe accidents. This issue is receiving increasing attention due to concerns that BWR MK I primary containment integrity would be lost should a significant mass of molten debris escape the reactor vessel during a severe accident. This paper presents a brief overview of domestic BWR secondary containment designs and highlights plant-specific features that could influence secondary containment severe accident survivability and accident mitigation effectiveness. Current issues surrounding secondary containment performance are discussed, and insights gained from recent ORNL secondary containment studies of Browns Ferry, Peach Bottom, and Shoreham are presented. Areas of significant uncertainty are identified and recommendations for future research are presented

Cost per severe accident as an index for severe accident consequence assessment and its applications

International Nuclear Information System (INIS)

Silva, Kampanart; Ishiwatari, Yuki; Takahara, Shogo

2014-01-01

The Fukushima Accident emphasizes the need to integrate the assessments of health effects, economic impacts, social impacts and environmental impacts, in order to perform a comprehensive consequence assessment of severe accidents in nuclear power plants. “Cost per severe accident” is introduced as an index for that purpose. The calculation methodology, including the consequence analysis using level 3 probabilistic risk assessment code OSCAAR and the calculation method of the cost per severe accident, is proposed. This methodology was applied to a virtual 1,100 MWe boiling water reactor. The breakdown of the cost per severe accident was provided. The radiation effect cost, the relocation cost and the decontamination cost were the three largest components. Sensitivity analyses were carried out, and parameters sensitive to cost per severe accident were specified. The cost per severe accident was compared with the amount of source terms, to demonstrate the performance of the cost per severe accident as an index to evaluate severe accident consequences. The ways to use the cost per severe accident for optimization of radiation protection countermeasures and for estimation of the effects of accident management strategies are discussed as its applications. - Highlights: • Cost per severe accident is used for severe accident consequence assessment. • Assessments of health, economic, social and environmental impacts are included. • Radiation effect, relocation and decontamination costs are important cost components. • Cost per severe accident can be used to optimize radiation protection measures. • Effects of accident management can be estimated using the cost per severe accident

MannDB – A microbial database of automated protein sequence analyses and evidence integration for protein characterization

Directory of Open Access Journals (Sweden)

Kuczmarski Thomas A

2006-10-01

Full Text Available Abstract Background MannDB was created to meet a need for rapid, comprehensive automated protein sequence analyses to support selection of proteins suitable as targets for driving the development of reagents for pathogen or protein toxin detection. Because a large number of open-source tools were needed, it was necessary to produce a software system to scale the computations for whole-proteome analysis. Thus, we built a fully automated system for executing software tools and for storage, integration, and display of automated protein sequence analysis and annotation data. Description MannDB is a relational database that organizes data resulting from fully automated, high-throughput protein-sequence analyses using open-source tools. Types of analyses provided include predictions of cleavage, chemical properties, classification, features, functional assignment, post-translational modifications, motifs, antigenicity, and secondary structure. Proteomes (lists of hypothetical and known proteins are downloaded and parsed from Genbank and then inserted into MannDB, and annotations from SwissProt are downloaded when identifiers are found in the Genbank entry or when identical sequences are identified. Currently 36 open-source tools are run against MannDB protein sequences either on local systems or by means of batch submission to external servers. In addition, BLAST against protein entries in MvirDB, our database of microbial virulence factors, is performed. A web client browser enables viewing of computational results and downloaded annotations, and a query tool enables structured and free-text search capabilities. When available, links to external databases, including MvirDB, are provided. MannDB contains whole-proteome analyses for at least one representative organism from each category of biological threat organism listed by APHIS, CDC, HHS, NIAID, USDA, USFDA, and WHO. Conclusion MannDB comprises a large number of genomes and comprehensive protein

Analysis of local subassembly accident in KALIMER

Energy Technology Data Exchange (ETDEWEB)

Kwon, Young Min; Jeong, Kwan Seong; Hahn, Do Hee

2000-10-01

Subassembly Accidents (S-A) in the Liquid Metal Reactor (LMR) may cause extensive clad and fuel melting and are thus regarded as a potential whole core accident initiator. The possibility of S-A occurrence must be very low frequency by the design features, and reactor must have specific instrumentation to interrupt the S-A sequences by causing a reactor shutdown. The evaluation of the relevant initiators, the event sequences which follow them, and their detection are the essence of the safety issue. Particularly, the phenomena of flow blockage caused by foreign materials and/or the debris from the failed fuel pin have been researched world-widely. The foreign strategies for dealing with the S-A and the associated safety issues with experimental and theoretical R and D results are reviewed. This report aims at obtaining information to reasonably evaluate the thermal-hydraulic effect of S-A for a wire-wrapped LMR fuel pin bundle. The mechanism of blockage formation and growth within a pin bundle and at the subassembly entrance is reviewed in the phenomenological aspect. Knowledge about the recent LMR subassembly design and operation procedure to prevent flow blockage will be reflected for KALIMER design later. The blockage analysis method including computer codes and related analytical models are reviewed. Especially SABRE4 code is discussed in detail. Preliminary analyses of flow blockage within a 271-pin driver subassembly have been performed using the SABRE4 computer code. As a result no sodium boiling occurred for the central 24-subchannel blockage as well as 6-subchannel blockage.

The accident at TEPCO's Fukushima Dai-ichi Nuclear Power Station - occurrence of the accident, current situation and Future

International Nuclear Information System (INIS)

Hirose, K.

2013-01-01

In this presentation author analyse course of accident on Fukushima Dai-chi NPPs as well as consequences of this disaster. The following parts are presented: (1) Occurrence of the accident; (2) Evacuation of the residential people; (3) Deterioration and protraction of the accident; (4) Impact on society; (5) Situation of decontamination; (6) Long-term steps towards decommissioning; (7) Situation of other nuclear power stations; (8) Conclusions and lessons learned.

Report on a radiotherapy underdose accident

Energy Technology Data Exchange (ETDEWEB)

Christodoulides, G; Christofides, S [Medical Physics Department, Nicosia General Hospital, 1450 Nicosia (Cyprus)

1999-12-31

Reporting information on accidents and incidents involving radiation sources provides a body of knowledge which can help to prevent accidents of a similar nature. Accident information has to be made available to users, manufacturers and regulators; An international effort to pool and analyse incident and accident information will provide more complete and reliable indicators of root causes and trends and recommendations for future accident avoidance. An accident due to human error involving a superficial x-ray therapy machine and patients treated for postoperative breast cancer is reported here. 43 women receiving radiotherapy treatment have received significantly less radiation dose than the prescribed dose. The worst dose percentage within the radiation field was 20% of the prescribed dose. The worst dose percentage on the operation scar of the breast was 52% of the prescribed radiation dose. The response to accidents/incidents in radiotherapy is discussed. (authors) 4 refs., 5 figs., 1 tabs.

The influence of the technologically advanced evacuation models on the risk analyses during accidents in LNG terminal

Energy Technology Data Exchange (ETDEWEB)

Stankovicj, Goran; Petelin, Stojan [Faculty for Maritime Studies and Transport, University of Ljubljana, Portorozh (Sierra Leone); others, and

2014-07-01

The evacuation of people located in different safety zones of an LNG terminal is a complex problem considering that the accidents involving LNG are very hazardous and post the biggest threat to the safety of the people located near the LNG leakage. The safety risk criteria define the parameters which one LNG terminal should meet in terms of safety. Those criteria also contain an evacuation as an evasive action with the objective to mitigate the influence of the LNG accident on the people at risk. Till date, not a lot of attention has been paid to technologically advanced evacuations intended for LNG terminals. Creating the technologically advanced evacuation influences directly on the decrease of the probability of fatalities P{sub f,i}, thus influencing the calculation of the individual risk as well as the societal risk which results in the positioning of the F-N curve in the acceptable part of the ALARP zone. With this paper, we aim to present the difference between the safety analyses in cases when conservative data for P{sub f,i} is being used while calculating the risk, and in cases when real data for P{sub f,i} is been used. (Author)

Scaling and design analyses of a scaled-down, high-temperature test facility for experimental investigation of the initial stages of a VHTR air-ingress accident

International Nuclear Information System (INIS)

Arcilesi, David J.; Ham, Tae Kyu; Kim, In Hun; Sun, Xiaodong; Christensen, Richard N.; Oh, Chang H.

2015-01-01

Highlights: • A 1/8th geometric-scale test facility that models the VHTR hot plenum is proposed. • Geometric scaling analysis is introduced for VHTR to analyze air-ingress accident. • Design calculations are performed to show that accident phenomenology is preserved. • Some analyses include time scale, hydraulic similarity and power scaling analysis. • Test facility has been constructed and shake-down tests are currently being carried out. - Abstract: A critical event in the safety analysis of the very high-temperature gas-cooled reactor (VHTR) is an air-ingress accident. This accident is initiated, in its worst case scenario, by a double-ended guillotine break of the coaxial cross vessel, which leads to a rapid reactor vessel depressurization. In a VHTR, the reactor vessel is located within a reactor cavity that is filled with air during normal operating conditions. Following the vessel depressurization, the dominant mode of ingress of an air–helium mixture into the reactor vessel will either be molecular diffusion or density-driven stratified flow. The mode of ingress is hypothesized to depend largely on the break conditions of the cross vessel. Since the time scales of these two ingress phenomena differ by orders of magnitude, it is imperative to understand under which conditions each of these mechanisms will dominate in the air ingress process. Computer models have been developed to analyze this type of accident scenario. There are, however, limited experimental data available to understand the phenomenology of the air-ingress accident and to validate these models. Therefore, there is a need to design and construct a scaled-down experimental test facility to simulate the air-ingress accident scenarios and to collect experimental data. The current paper focuses on the analyses performed for the design and operation of a 1/8th geometric scale (by height and diameter), high-temperature test facility. A geometric scaling analysis for the VHTR, a time

Thermal and hydraulic behaviour of CANDU cores under severe accident conditions - final report. Vol. 1

International Nuclear Information System (INIS)

Rogers, J.T.

1984-06-01

This report gives the results of a study of the thermo-hydraulic aspects of severe accident sequences in CANDU reactors. The accident sequences considered are the loss of the moderator cooling system and the loss of the moderator heat sink, each following a large loss-of-coolant accident accompanied by loss of emergency coolant injection. Factors considered include expulsion and boil-off of the moderator, uncovery, overheating and disintegration of the fuel channels, quenching of channel debris, re-heating of channel debris following complete moderator expulsion, formation and possible boiling of a molten pool of core debris and the effectiveness of the cooling of the calandria wall by the shield tank water during the accident sequences. The effects of these accident sequences on the reactor containment are also considered. Results show that there would be no gross melting of fuel during moderator expulsion from the calandria, and for a considerable time thereafter, as quenched core debris re-heats. Core melting would not begin until about 135 minutes after accident initiation in a loss of the moderator cooling system and until about 30 minutes in a loss of the moderator heat sink. Eventually, a pool of molten material would form in the bottom of the calandria, which may or may not boil, depending on property values. In all cases, the molten core would be contained within the calandria, as long as the shield tank water cooling system remains operational. Finally, in the period from 8 to 50 hours after the initiation of the accident, the molten core would re-solidify within the calandria. There would be no consequent damage to containment resulting from these accident sequences, nor would there be a significant increase in fission product releases from containment above those that would otherwise occur in a dual failure LOCA plus LOECI

Risk evaluation method for faults by engineering approach. (2) Application concept of margin analysis utilizing accident sequences

International Nuclear Information System (INIS)

Kamiya, Masanobu; Kanaida, Syuuji; Kamiya, Kouichi; Sato, Kunihiko; Kuroiwa, Katsuya

2016-01-01

The influence of the fault displacement on the facility should to be evaluated not only by the activity of the fault but also by obtaining risk information by considering scenarios including such as the frequency and the degree of the hazard, which should be an appropriate approach for nuclear safety. An applicable concept of margin analysis utilizing accident sequences for evaluating the influence of the fault displacement is proposed. By use of this analysis, we can evaluate of the safety functions and margin for core damage, verify the efficiency of equipment of portable type and make a decision to take additional measures to reduce the risk by using obtained risk information. (author)

Preventing marine accidents caused by technology-induced human error

OpenAIRE

Bielić, Toni; Hasanspahić, Nermin; Čulin, Jelena

2017-01-01

The objective of embedding technology on board ships, to improve safety, is not fully accomplished. The paper studies marine accidents caused by human error resulting from improper human-technology interaction. The aim of the paper is to propose measures to prevent reoccurrence of such accidents. This study analyses the marine accident reports issued by Marine Accidents Investigation Branch covering the period from 2012 to 2014. The factors that caused these accidents are examined and categor...

Accident source terms for boiling water reactors with high burnup cores.

Energy Technology Data Exchange (ETDEWEB)

Gauntt, Randall O.; Powers, Dana Auburn; Leonard, Mark Thomas

2007-11-01

The primary objective of this report is to provide the technical basis for development of recommendations for updates to the NUREG-1465 Source Term for BWRs that will extend its applicability to accidents involving high burnup (HBU) cores. However, a secondary objective is to re-examine the fundamental characteristics of the prescription for fission product release to containment described by NUREG-1465. This secondary objective is motivated by an interest to understand the extent to which research into the release and behaviors of radionuclides under accident conditions has altered best-estimate calculations of the integral response of BWRs to severe core damage sequences and the resulting radiological source terms to containment. This report, therefore, documents specific results of fission product source term analyses that will form the basis for the HBU supplement to NUREG-1465. However, commentary is also provided on observed differences between the composite results of the source term calculations performed here and those reflected NUREG-1465 itself.

Stepwise integral scaling method for severe accident analysis and its application to corium dispersion in direct containment heating

International Nuclear Information System (INIS)

Ishii, M.; Zhang, G.; No, H. C.; Eltwila, F.

1994-01-01

Accident sequences which lead to severe core damage and to possible radioactive fission products into the environment have a very low probability. However, the interest in this area increased significantly due to the occurrence of the small break loss-of-coolant accident at TMI-2 which led to partial core damage, and of the Chernobyl accident in the former USSR which led to extensive core disassembly and significant release of fission products over several countries. In particular, the latter accident raised the international concern over the potential consequences of severe accidents in nuclear reactor systems. One of the significant shortcomings in the analyses of severe accidents is the lack of well-established and reliable scaling criteria for various multiphase flow phenomena. However, the scaling criteria are essential to the severe accident, because the full scale tests are basically impossible to perform. They are required for (1) designing scaled down or simulation experiments, (2) evaluating data and extrapolating the data to prototypic conditions, and (3) developing correctly scaled physical models and correlations. In view of this, a new scaling method is developed for the analysis of severe accidents. Its approach is quite different from the conventional methods. In order to demonstrate its applicability, this new stepwise integral scaling method has been applied to the analysis of the corium dispersion problem in the direct containment heating. ((orig.))

Atucha-I source terms for sequences initiated by transients

International Nuclear Information System (INIS)

Baron, J.; Bastianelli, B.

1997-01-01

The present work is part of an expected source terms study in the Atucha I nuclear power plant during severe accidents. From the accident sequences with a significant probability to produce core damage, those initiated by operational transients have been identified as the most relevant. These sequences have some common characteristics, in the sense that all of them resume in the opening of the primary system safety valves, and leave this path open for the coolant loss. In the case these sequences continue as severe accidents, the same path will be used for the release of the radionuclides, from the core, through the primary system and to the containment. Later in the severe accident sequence, the failure of the pressure vessel will occur, and the corium will fall inside the reactor cavity, interacting with the concrete. During these processes, more radioactive products will be released inside the containment. In the present work the severe accident simulation initiated by a blackout is performed, from the point of view of the phenomenology of the behavior of the radioactive products, as they are transported in the piping, during the core-concrete interactions, and inside the containment buildings until it failure. The final result is the source term into the atmosphere. (author) [es

Comparison between MARCH-3 and MAAP-3 thermal-hydraulic results for a severe accident in a BWR system with MARK-III containment

International Nuclear Information System (INIS)

Barbucci, P.; Guidi, L.; Mariotti, G.

1988-01-01

A comparison between results provided by the Source Term Code Package and by the MAAP-3 code for a PWR with full pressure containment was presented. Thereafter the same two methodologies were used to analyse a severe accident sequence in a typical BWR power plant equipped with a General Electric BWR 6 reactor, rated at 2894 MWt, and a MARK-III type containment. As a reference sequence the TQUV was chosen. This sequence is characterized by a transient (T) with loss of feedwater (Q) and loss of all Emergency Core Cooling Systems, both at high pressure (U) and, after the intervention of the Automatic Depressurization System (ADS), at low pressure (V). After the vessel, failure two basic scenarios for the containment response were analysed: in the first one the pedestal is always dry, in the second one it is fully flooded. Typical limestone/common sand and basaltic concrete compositions were considered. In the following sections the obtained results will be shown with the main purpose to point out the different phenomenological models of the two codes rather than to look for the true plant response to such a severe accident. After the presentation of the most important physical models and of the main assumptions for the analyses (sects. 2 and 4), the comparison will be performed for the in-vessel phase, in section 3, and for the ex-vessel phase, in section 5

Critique of the RASMUSSEN report (WASH-1400) on accident risks in U.S. commercial nuclear power plants

International Nuclear Information System (INIS)

Krueger, F.W.

1976-06-01

The RASMUSSEN study represents an excellent survey of the current possibilities to assess quantitatively the operational risk of nuclear power plants. To close the big gaps which turned out to be still existent in calculating the possible accidents sequences and their consequences but also in the statistical materials, only rough models could be used because of the limited capability of theoretical analyses to replace lacking experience. Contrary to previous studies the risk estimates have not deliberately been maximized, apart from the fact that in many cases no 'safe' side does a priori exist. Rather, the RASMUSSEN study tried to make 'reasonable realistic' assumptions concerning accident sequences and activity release consequences, but it is difficult to refute that the results will tend to underestimate systematically the accident consequences. Besides, in every case the range of uncertainty will very likely be greater than stated in the study, not least also because the results are substantially influenced by technical features of the nuclear power plants under discussion. This should be given attention in discussions using the quantitative results of the study as well as the fact that planning, construction and operation of nuclear power plants must be done with utmost accuracy to achieve the specified low orders of risk. (author)

Accident selection methodology for TA-55 FSAR

International Nuclear Information System (INIS)

Letellier, B.C.; Pan, P.Y.; Sasser, M.K.

1995-01-01

In the past, the selection of representative accidents for refined analysis from the numerous scenarios identified in hazards analyses (HAs) has involved significant judgment and has been difficult to defend. As part of upgrading the Final Safety Analysis Report (FSAR) for the TA-55 plutonium facility at the Los Alamos National Laboratory, an accident selection process was developed that is mostly mechanical and reproducible in nature and fulfills the requirements of the Department of Energy (DOE) Standard 3009 and DOE Order 5480.23. Among the objectives specified by this guidance are the requirements that accident screening (1) consider accidents during normal and abnormal operating conditions, (2) consider both design basis and beyond design basis accidents, (3) characterize accidents by category (operational, natural phenomena, etc.) and by type (spill, explosion, fire, etc.), and (4) identify accidents that bound all foreseeable accident types. The accident selection process described here in the context of the TA-55 FSAR is applicable to all types of DOE facilities

Modelling and analysis of severe accidents for VVER-1000 reactors

International Nuclear Information System (INIS)

Tusheva, Polina

2012-01-01

Accident conditions involving significant core degradation are termed severe accidents /IAEA: NS-G-2.15/. Despite the low probability of occurrence of such events, the investigation of severe accident scenarios is an important part of the nuclear safety research. Considering a hypothetical core melt down scenario in a VVER-1000 light water reactor, the early in-vessel phase focusing on the thermal-hydraulic phenomena, and the late in-vessel phase focusing on the melt relocation into the reactor pressure vessel (RPV) lower head, are investigated. The objective of this work is the assessment of severe accident management procedures for VVER-1000 reactors, i.e. the estimation of the maximum period of time available for taking appropriate measures and particular decisions by the plant personnel. During high pressure severe accident sequences it is of prime importance to depressurize the primary circuit in order to allow for effective injection from the emergency core cooling systems and to avoid reactor pressure vessel failure at high pressure that could cause direct containment heating and subsequent challenge to the containment structure. Therefore different accident management measures were investigated for the in-vessel phase of a hypothetical station blackout accident using the severe accident code ASTEC, the mechanistic code ATHLET and the multi-purpose code system ANSYS. The analyses performed on the PHEBUS ISP-46 experiment, as well as simulations of small break loss of coolant accident and station blackout scenarios were used to contribute to the validation and improvement of the integral severe accident code ASTEC. Investigations on the applicability and the effectiveness of accident management procedures in the preventive domain, as well as detailed analyses on the thermal-hydraulic phenomena during the early in-vessel phase of a station blackout accident have been performed with the mechanistic code ATHLET. The results of the simulations show, that the

Safety demonstration analyses on criticality for severe accident during overland transport of fresh nuclear fuel

International Nuclear Information System (INIS)

Takahashi, Satoshi; Okuno, Hiroshi; Yamada, Kenji; Watanabe, Kouji; Nomura, Yasushi; Miyoshi, Yoshinori

2005-01-01

Criticality safety analysis was performed for transport packages of uranium dioxide powder or of fresh PWR fuel involved in a severe accident during overland transportation, and as a result, sub-criticality was confirmed against impact accident conditions such as loaded by a drop from high position to a concrete or asphalt surface, and fire accident conditions such as caused by collisions with an oil tank trailer carrying lots of inflammable material in open air, or with a commonly used two-ton-truck inside an unventilated tunnel. (author)

The nature of reactor accidents

International Nuclear Information System (INIS)

Domaratzki, Z.; Campbell, F.R.; Atchison, R.J.

1981-01-01

Reactor accidents are events which result in the release of radioactive material from a nuclear power plant due to the failure of one or more critical components of that plant. The failures, depending on their number and type, can result in releases whose consequences range from negligible to catastrophic. By way of examples, this paper describes four specific accidents which cover this range of consequence: failure of a reactor control system, loss of coolant, loss of coolant with impaired containment, and reactor core meltdown. For each a possible sequence of events and an estimate of the expected frequency are presented

Modelling of HTR Confinement Behaviour during Accidents Involving Breach of the Helium Pressure Boundary

Directory of Open Access Journals (Sweden)

Joan Fontanet

2009-01-01

Full Text Available Development of HTRs requires the performance of a thorough safety study, which includes accident analyses. Confinement building performance is a key element of the system since the behaviour of aerosol and attached fission products within the building is of an utmost relevance in terms of the potential source term to the environment. This paper explores the available simulation capabilities (ASTEC and CONTAIN codes and illustrates the performance of a postulated HTR vented confinement under prototypical accident conditions by a scoping study based on two accident sequences characterized by Helium Pressure Boundary breaches, a small and a large break. The results obtained indicate that both codes predict very similar thermal-hydraulic responses of the confinement both in magnitude and timing. As for the aerosol behaviour, both codes predict that most of the inventory coming into the confinement is eventually depleted on the walls and only about 1% of the aerosol dust is released to the environment. The crosscomparison of codes states that largest differences are in the intercompartmental flows and the in-compartment gas composition.

MELCOR 1.8.2 Analyses in Support of ITER's RPrS

International Nuclear Information System (INIS)

Brad J Merrill

2008-01-01

The International Thermonuclear Experimental Reactor (ITER) Program is performing accident analyses for ITER's 'Rapport Preliminaire de Surete' (Report Preliminary on Safety - RPrS) with a modified version of the MELCOR 1.8.2 code. The RPrS is an ITER safety document required in the ITER licensing process to obtain a 'Decret Autorisation de Construction' (a Decree Authorizing Construction - DAC) for the ITER device. This report documents the accident analyses performed by the US with the MELCOR 1.8.2 code in support of the ITER RPrS effort. This work was funded through an ITER Task Agreement for MELCOR Quality Assurance and Safety Analyses. Under this agreement, the US was tasked with performing analyses for three accident scenarios in the ITER facility. Contained within the text of this report are discussions that identify the cause of these accidents, descriptions of how these accidents are likely to proceed, the method used to analyze the consequences of these accidents, and discussions of the transient thermal hydraulic and radiological release results for these accidents

A study on the operator's errors of commission (EOC) in accident scenarios of nuclear power plants: methodology development and application

International Nuclear Information System (INIS)

Kim, Jae Whan; Jung, Won Dea; Park, Jin Kyun; Kang, Da Il

2003-04-01

As the concern on the operator's inappropriate interventions, the so-called Errors Of Commission (EOCs), that can exacerbate the plant safety has been raised, much of interest in the identification and analysis of EOC events from the risk assessment perspective has been increased. Also, one of the items in need of improvement for the conventional PSA and HRA that consider only the system-demanding human actions is the inclusion of the operator's EOC events into the PSA model. In this study, we propose a methodology for identifying and analysing human errors of commission that might be occurring from the failures in situation assessment and decision making during accident progressions given an initiating event. In order to achieve this goal, the following research items have been performed: Firstly, we analysed the error causes or situations contributed to the occurrence of EOCs in several incidents/accidents of nuclear power plants. Secondly, limitations of the advanced HRAs in treating EOCs were reviewed, and a requirement for a new methodology for analysing EOCs was established. Thirdly, based on these accomplishments a methodology for identifying and analysing EOC events inducible from the failures in situation assessment and decision making was proposed and applied to all the accident sequences of YGN 3 and 4 NPP which resulted in the identification of about 10 EOC situations

Probabilistic risk assessment for the Los Alamos Meson Physics Facility worst-case design-basis accident

International Nuclear Information System (INIS)

Sharirli, M.; Butner, J.M.; Rand, J.L.; Macek, R.J.; McKinney, S.J.; Roush, M.L.

1992-01-01

This paper presents results from a Los Alamos National Laboratory Engineering and Safety Analysis Group assessment of the worse-case design-basis accident associated with the Clinton P. Anderson Meson Physics Facility (LAMPF)/Weapons Neutron Research (WNR) Facility. The primary goal of the analysis was to quantify the accident sequences that result in personnel radiation exposure in the WNR Experimental Hall following the worst-case design-basis accident, a complete spill of the LAMPF accelerator 1L beam. This study also provides information regarding the roles of hardware systems and operators in these sequences, and insights regarding the areas where improvements can increase facility-operation safety. Results also include confidence ranges to incorporate combined effects of uncertainties in probability estimates and importance measures to determine how variations in individual events affect the frequencies in accident sequences

Swedish REGULATORY APPROACH TO SAFETY Assessment AND SEVERE ACCIDENT MANAGEMENT

International Nuclear Information System (INIS)

Frid, W.; Sandervaag, O.

1997-01-01

The Swedish regulatory approach to safety assessment and severe accident management is briefly described. The safety assessment program, which focuses on prevention of incidents and accidents, has three main components: periodic safety reviews, probabilistic safety analysis, and analysis of postulated disturbances and accident progression sequences. Management and man-technology-organisation issues, as well as inspections, play a key role in safety assessment. Basis for severe accident management were established by the Government decisions in 1981 and 1986. By the end of 1988, the severe accident mitigation systems and emergency operating procedures were implemented at all Swedish reactors. The severe accident research has continued after 1988 for further verification of the protection provided by the systems and reduction of remaining uncertainties in risk dominant phenomena

Computer Based Road Accident Reconstruction Experiences

Directory of Open Access Journals (Sweden)

Milan Batista

2005-03-01

Full Text Available Since road accident analyses and reconstructions are increasinglybased on specific computer software for simulationof vehicle d1iving dynamics and collision dynamics, and forsimulation of a set of trial runs from which the model that bestdescribes a real event can be selected, the paper presents anoverview of some computer software and methods available toaccident reconstruction experts. Besides being time-saving,when properly used such computer software can provide moreauthentic and more trustworthy accident reconstruction, thereforepractical experiences while using computer software toolsfor road accident reconstruction obtained in the TransportSafety Laboratory at the Faculty for Maritime Studies andTransport of the University of Ljubljana are presented and discussed.This paper addresses also software technology for extractingmaximum information from the accident photo-documentationto support accident reconstruction based on the simulationsoftware, as well as the field work of reconstruction expertsor police on the road accident scene defined by this technology.

Structural aspects of the Chernobyl accident

International Nuclear Information System (INIS)

Murray, R.C.; Cummings, G.E.

1988-01-01

On April 26, 1986 the world's worst nuclear power plant accident occurred at the Unit 4 of the Chernobyl Nuclear Power Station in the USSR. This paper presents a discussion of the design of the Chernobyl Power Plant, the sequence of events that led to the accident and the damage caused by the resulting explosion. The structural design features that contributed to the accident and resulting damage will be highlighted. Photographs and sketches obtained from various worldwide news agencies will be shown to try and gain a perspective of the extent of the damage. The aftermath, clean-up, and current situation will be discussed and the important lessons learned for the structural engineer will be presented. 15 refs., 10 figs

CARNSORE: Hypothetical reactor accident study

International Nuclear Information System (INIS)

Walmod-Larsen, O.; Jensen, N.O.; Kristensen, L.; Meide, A.; Nedergaard, K.L.; Nielsen, F.; Lundtang Petersen, E.; Petersen, T.; Thykier-Nielsen, S.

1984-06-01

Two types of design-basis accident and a series of hypothetical core-melt accidents to a 600 MWe reactor are described and their consequences assessed. The PLUCON 2 model was used to calculate the consequences which are presented in terms of individual and collective doses, as well as early and late health consequences. The site proposed for the nucelar power station is Carnsore Point, County Wexford, south-east Ireland. The release fractions for the accidents described are those given in WASH-1400. The analyses are based on the resident population as given in the 1979 census and on 20 years of data from the meteorological stations at Rosslare Harbour, 8.5 km north of the site. The consequences of one of the hypothetical core-melt accidents are described in detail in a meteorological parametric study. Likewise the consequences of the worst conceivable combination of situations are described. Finally, the release fraction in one accident is varied and the consequences of a proposed, more probable ''Class 9 accident'' are presented. (author)

Jerky driving--An indicator of accident proneness?

Science.gov (United States)

Bagdadi, Omar; Várhelyi, András

2011-07-01

This study uses continuously logged driving data from 166 private cars to derive the level of jerks caused by the drivers during everyday driving. The number of critical jerks found in the data is analysed and compared with the self-reported accident involvement of the drivers. The results show that the expected number of accidents for a driver increases with the number of critical jerks caused by the driver. Jerk analyses make it possible to identify safety critical driving behaviour or "accident prone" drivers. They also facilitate the development of safety measures such as active safety systems or advanced driver assistance systems, ADAS, which could be adapted for specific groups of drivers or specific risky driving behaviour. Copyright © 2011 Elsevier Ltd. All rights reserved.

Severe accidents in Nuclear Power Plants

International Nuclear Information System (INIS)

Valle Cepero, R.; Castillo Alvarez, J.; Ramon Fuente, J.

1996-01-01

For the assessment of the safety of nuclear power plants it is of great importance the analyses of severe accidents since they allow to estimate the possible failure models of the containment, and also permit knowing the magnitude and composition of the radioactive material that would be released to the environment in case of an accident upon population and the environment. This paper presents in general terms the basic principles for conducting the analysis of severe accidents, the fundamental sources in the generation of radionuclides and aerosols, the transportation and deposition processes, and also makes reference to de main codes used in the modulation of severe accidents. The final part of the paper contents information on how severe accidents are dialed with the regulatory point view in different countries

The NEA benchmark study of the accident at the Fukushima Daiichi NPP

International Nuclear Information System (INIS)

Koganeya, Toshiyuki

2015-01-01

In November 2012, the NEA, under the aegis of the Committee on the Safety of Nuclear Installations (CSNI), initiated a joint research project called the Benchmark Study of the Accident at the Fukushima Daiichi Nuclear Power Station (BSAF). Objectives of this project include supporting Fukushima Daiichi decommissioning by analysing accident progression and the current status of the reactors, such as fuel debris distribution in the reactor pressure vessels and primary containment vessels in preparation for fuel debris removal. A second objective of the project is to improve SA (severe analysis) codes through comparisons with data from the Fukushima reactors. So as to enhance communication between analysts and those involved in decommissioning activities, participants in the project have been discussing the remaining uncertainties in relation to understanding the accident and the data needs from the viewpoint of the analysts. Since the accident sequences at the Fukushima Daiichi site include a wide range of phenomena, a phased approach is being applied in this benchmark exercise while awaiting more detailed information on debris examination and other factors. This article provides an overview of the project (scope, input data and boundary conditions, participants (from eight countries), analytical approach - common case and best estimate case) as well as an outline of the project's next phase (BASF phase 2) that begins in June 2015

Chernobylsk accident (Causes and Consequences)- Part 2

International Nuclear Information System (INIS)

Esteves, D.

1986-09-01

The causes and consequences of the nuclear accident at Chernobylsk-4 reactor are shortly described. The informations were provided by Russian during the specialist meeting, carried out at seat of IAEA. The Russian nuclear panorama; the site, nuclear power plant characteristics and sequence of events; the immediate measurements after accident; monitoring/radioactive releases; environmental contamination and ecological consequences; measurements of emergency; recommendations to increase the nuclear safety; and recommendations of work groups, are presented. (M.C.K.) [pt

Analysis and research status of severe core damage accidents

International Nuclear Information System (INIS)

1984-03-01

The Severe Core Damage Research and Analysis Task Force was established in Nuclear Safety Research Center, Tokai Research Establishment, JAERI, in May, 1982 to make a quantitative analysis on the issues related with the severe core damage accident and also to survey the present status of the research and provide the required research subjects on the severe core damage accident. This report summarizes the results of the works performed by the Task Force during last one and half years. The main subjects investigated are as follows; (1) Discussion on the purposes and necessities of severe core damage accident research, (2) proposal of phenomenological research subjects required in Japan, (3) analysis of severe core damage accidents and identification of risk dominant accident sequences, (4) investigation of significant physical phenomena in severe core damage accidents, and (5) survey of the research status. (author)

Accident at the Three Mile Island Nuclear Powerplant. Part 1. Oversight hearings before a task force of the Subcommittee on Energy and the Environment of the Committee on Interior and Insular Affairs, House of Representatives, Ninety-Sixth Congress

International Nuclear Information System (INIS)

Anon.

1979-01-01

The Committee on Interior and Insular Affairs conducted an informal review of the accident beginning on March 28, 1979 at the Three Mile Island Nuclear Power Plant. Officials of the Nuclear Regulatory Commission, plant operating personnel employed by General Public Utilities, and representatives of the reactor manufacturer, Babcock and Wilcox Company, related their activities during the accident and their analyses of the sequence of events

A reactivity accidents simulation of the Fort Saint Vrain HTGR

International Nuclear Information System (INIS)

Fainer, Gerson

1980-01-01

A reactivity accidents analysis of the Fort Saint Vrain HTGR was made. The following accidents were analysed 1) A rod pair withdrawal accident during normal operation, 2) A rod pair ejection accident, 3) A rod pair withdrawal accident during startup operations at source levels and 4) Multiple rod pair withdrawal accident. All the simulations were performed by using the BLOOST-6 nuclear code The steady state reactor operation results obtained with the code were consistent with the design reactor data. The numerical analysis showed that all accidents - except the first one - cause particle failure. (author)

Industrial accidents triggered by lightning.

Science.gov (United States)

Renni, Elisabetta; Krausmann, Elisabeth; Cozzani, Valerio

2010-12-15

Natural disasters can cause major accidents in chemical facilities where they can lead to the release of hazardous materials which in turn can result in fires, explosions or toxic dispersion. Lightning strikes are the most frequent cause of major accidents triggered by natural events. In order to contribute towards the development of a quantitative approach for assessing lightning risk at industrial facilities, lightning-triggered accident case histories were retrieved from the major industrial accident databases and analysed to extract information on types of vulnerable equipment, failure dynamics and damage states, as well as on the final consequences of the event. The most vulnerable category of equipment is storage tanks. Lightning damage is incurred by immediate ignition, electrical and electronic systems failure or structural damage with subsequent release. Toxic releases and tank fires tend to be the most common scenarios associated with lightning strikes. Oil, diesel and gasoline are the substances most frequently released during lightning-triggered Natech accidents. Copyright © 2010 Elsevier B.V. All rights reserved.

Status of science and technology with respect of preparation and evaluation of accident analyses and the use of analysis simulators. Final report; Ermittlung des Standes von Wissenschaft und Technik bei der Durchfuehrung und Bewertung von Stoerfallanalysen und der Verwendung von Analysesimulatoren. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Draeger, P.; Cester, F.; Erdmann, W.; and others

2011-12-15

The final report on the status of science and technology with respect of preparation and evaluation of accident analyses and the use of analysis simulators includes the following work packages: uncertainty analysis for an incident in BWR, preparation and evaluation of accident analyses considering the requirements in the reviewed standards, safeguarding of the mixing modeling for the evaluation of re-criticality accidents, answering of recent questions concerning reactor and containment behavior during incidents and accidents, actualization and refinement of data bases for plant specific analysis simulators.

Dose calculations for severe LWR accident scenarios

International Nuclear Information System (INIS)

Margulies, T.S.; Martin, J.A. Jr.

1984-05-01

This report presents a set of precalculated doses based on a set of postulated accident releases and intended for use in emergency planning and emergency response. Doses were calculated for the PWR (Pressurized Water Reactor) accident categories of the Reactor Safety Study (WASH-1400) using the CRAC (Calculations of Reactor Accident Consequences) code. Whole body and thyroid doses are presented for a selected set of weather cases. For each weather case these calculations were performed for various times and distances including three different dose pathways - cloud (plume) shine, ground shine and inhalation. During an emergency this information can be useful since it is immediately available for projecting offsite radiological doses based on reactor accident sequence information in the absence of plant measurements of emission rates (source terms). It can be used for emergency drill scenario development as well

Safety climate and accidents at work

DEFF Research Database (Denmark)

Ajslev, Jeppe; Dastjerdi, Efat Lali; Dyreborg, Johnny

2017-01-01

Aim: Occupational safety climate is utilized as a way to measure the risk of accidents and injuries at work. This study investigates which factors are associated with safety climate and accidents at work. Methods: In the 2012 round of the Danish Work Environment and Health Study, 15,144 workers...... from the general working population of Denmark replied to questions about safety climate and accidents at work. Mutually adjusted logistic regression analyses determined the association between variables. Results: Within the last year, 5.7% had experienced an accident resulting in sickness absence....... The number of safety climate problems was progressively associated with the odds ratio (OR) for accidents. For one safety climate problem the OR for accidents was 2.01 (95% CI 1.67–2.42), for four or more safety climate problems the OR was 4.57 (95% CI 3.64–5.74). Young workers (18–24 years) had higher odds...

Nuclear power plants: Results of recent safety analyses

International Nuclear Information System (INIS)

Steinmetz, E.

1987-01-01

The contributions deal with the problems posed by low radiation doses, with the information currently available from analyses of the Chernobyl reactor accident, and with risk assessments in connection with nuclear power plant accidents. Other points of interest include latest results on fission product release from reactor core or reactor building, advanced atmospheric dispersion models for incident and accident analyses, reliability studies on safety systems, and assessment of fire hazard in nuclear installations. The various contributions are found as separate entries in the database. (DG) [de

A framework for the assessment of severe accident management strategies

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.

1993-09-01

Severe accident management can be defined as the use of existing and/or altemative resources, systems and actors to prevent or mitigate a core-melt accident. For each accident sequence and each combination of severe accident management strategies, there may be several options available to the operator, and each involves phenomenological and operational considerations regarding uncertainty. Operational uncertainties include operator, system and instrumentation behavior during an accident. A framework based on decision trees and influence diagrams has been developed which incorporates such criteria as feasibility, effectiveness, and adverse effects, for evaluating potential severe accident management strategies. The framework is also capable of propagating both data and model uncertainty. It is applied to several potential strategies including PWR cavity flooding, BWR drywell flooding, PWR depressurization and PWR feed and bleed

A framework for the assessment of severe accident management strategies

Energy Technology Data Exchange (ETDEWEB)

Kastenberg, W.E. [ed.; Apostolakis, G.; Dhir, V.K. [California Univ., Los Angeles, CA (United States). Dept. of Mechanical, Aerospace and Nuclear Engineering] [and others

1993-09-01

Severe accident management can be defined as the use of existing and/or altemative resources, systems and actors to prevent or mitigate a core-melt accident. For each accident sequence and each combination of severe accident management strategies, there may be several options available to the operator, and each involves phenomenological and operational considerations regarding uncertainty. Operational uncertainties include operator, system and instrumentation behavior during an accident. A framework based on decision trees and influence diagrams has been developed which incorporates such criteria as feasibility, effectiveness, and adverse effects, for evaluating potential severe accident management strategies. The framework is also capable of propagating both data and model uncertainty. It is applied to several potential strategies including PWR cavity flooding, BWR drywell flooding, PWR depressurization and PWR feed and bleed.

Effects of the Chernobyl accident on public perceptions of nuclear plant accident risks

International Nuclear Information System (INIS)

Lindell, M.K.; Perry, R.W.

1990-01-01

Assessments of public perceptions of the characteristics of a nuclear power plant accident and affective responses to its likelihood were conducted 5 months before and 1 month after the Chernobyl accident. Analyses of data from 69 residents of southwestern Washington showed significant test-retest correlations for only 10 of 18 variables--accident likelihood, three measures of impact characteristics, three measures of affective reactions, and hazard knowledge by governmental sources. Of these variables, only two had significant changes in mean ratings; frequency of thought and frequency of discussion about a nearby nuclear power plant both increased. While there were significant changes only for two personal consequences (expectations of cancer and genetic effects), both of these decreased. The results of this study indicate that more attention should be given to assessing the stability of risk perceptions over time. Moreover, the data demonstrate that experience with a major accident can actually decrease rather than increase perceptions of threat

Computer codes developed in FRG to analyse hypothetical meltdown accidents

International Nuclear Information System (INIS)

Hassmann, K.; Hosemann, J.P.; Koerber, H.; Reineke, H.

1978-01-01

It is the purpose of this paper to give the status of all significant computer codes developed in the core melt-down project which is incorporated in the light water reactor safety research program of the Federal Ministry of Research and Technology. For standard pressurized water reactors, results of some computer codes will be presented, describing the course and the duration of the hypothetical core meltdown accident. (author)

The nuclear accidents: Causes and consequences

International Nuclear Information System (INIS)

Rochd, M.

1988-01-01

The author discussed and compared the real causes of T.M.I. and Chernobyl accidents and cited their consequences. To better understand how these accidents occurred, a brief description of PWR type (reactor type of T.M.I.) and of RBMK type (reactor type of Chernobyl) has been presented. The author has also set out briefly the safety analysis objectives and the three barriers established to protect the public against the radiological consequences. To distinguish failures that cause severe accidents and to analyze them in details, it is necessary to classify the accidents. There are many ways to do it according to their initiator event, or to their frequency, or to their degree of gravity. The safety criteria adopted by nuclear industry have been explained. These criteria specify the limits of certain physical parameters that should not be exceeded in case of incidents or accidents. To compare the real causes of T.M.I. and Chernobyl accidents, the events that led to both have been presented. As observed the main common contributing factors in both cases are that the operators did not pay attention to warnings and signals that were available to them and that they were not trained to handle these accident sequences. The essential conclusions derived from these severe accidents are: -The improvement of operators competence contribute to reduce the accident risks; -The rapid and correct diagnosis of real conditions at each point of the accidents permits an appropriate behavior that would bring the plant to a stable state; -Competent technical teams have to intervene and to assist the operators in case of emergency; -Emergency plans and an international collaboration are necessary to limit the accident risks. 11 figs. (author)

CNE (central nuclear en Embalse): probabilistic safety study. Loss-of-coolant accidents. Analysis through events sequence

International Nuclear Information System (INIS)

Layral, S.I.

1987-01-01

The aim of this study was to perform for the Embalse nuclear power plant, a probabilistic evaluation of loss-of-coolant accidents (LOCA) to identify the risks associated with them and to determine their acceptability in accordance with norms. This study includes all ruptures in the primary system that produce the automatic activation of 'emergency core cooling system'. Three starting events were selected for the probabilistic evaluation: 100% rupture of an input collector; 5% rupture of an input collector; 1.2% rupture of an input collector. At this stage the evaluation is focussed on the identification and quantization of the main failure sequences that follow a LOCA and lead to an uncontrolled reactor state or 'core meltdown'. The most important contribution to the core meltdown due to LOCA is the failure of supplies that are required for the emergency core cooling system. (Author)

Simulation of LOF accidents with directly electrical heated UO2 pins

International Nuclear Information System (INIS)

Alexas, A.

1976-01-01

The behavior of directly electrical heated UO 2 pins has been investigated under loss of coolant conditions. Two types of hypothetical accidents have been simulated, first, a LOF accident without power excursion (LOF accident) and second, a LOF accident with subsequent power excursion (LOF-TOP accident). A high-speed film shows the sequence of events for two characteristic experiments. In consequence of the high-speed film analysis as well as the metallographical evaluation statements are given in respect to the cladding meltdown process, the fuel melt fraction and the energy input from the beginning of a power transient to the beginning of the molten fuel ejections

Modeling and analyses of postulated UF6 release accidents in gaseous diffusion plant

International Nuclear Information System (INIS)

Kim, S.H.; Taleyarkhan, R.P.; Keith, K.D.; Schmidt, R.W.; Carter, J.C.; Dyer, R.H.

1995-10-01

Computer models have been developed to simulate the transient behavior of aerosols and vapors as a result of a postulated accident involving the release of uranium hexafluoride (UF 6 ) into the process building of a gaseous diffusion plant. UF 6 undergoes an exothermic chemical reaction with moisture (H 2 O) in the air to form hydrogen fluoride (HF) and radioactive uranyl fluoride (UO 2 F 2 ). As part of a facility-wide safety evaluation, this study evaluated source terms consisting of UO 2 F 2 as well as HF during a postulated UF 6 release accident in a process building. In the postulated accident scenario, ∼7900 kg (17,500 lb) of hot UF 6 vapor is released over a 5 min period from the process piping into the atmosphere of a large process building. UO 2 F 2 mainly remains as airborne-solid particles (aerosols), and HF is in a vapor form. Some UO 2 F 2 aerosols are removed from the air flow due to gravitational settling. The HF and the remaining UO 2 F 2 are mixed with air and exhausted through the building ventilation system. The MELCOR computer code was selected for simulating aerosols and vapor transport in the process building. MELCOR model was first used to develop a single volume representation of a process building and its results were compared with those from past lumped parameter models specifically developed for studying UF 6 release accidents. Preliminary results indicate that MELCOR predicted results (using a lumped formulation) are comparable with those from previously developed models

Accidents in radiotherapy: Lack of quality assurance?

International Nuclear Information System (INIS)

Novotny, J.

1997-01-01

About 150 radiological accidents, involving more than 3000 patients with adverse effects, 15 patient's fatalities and about 5000 staff and public exposures have been collected and analysed. Out of 67 analysed accidents in external beam therapy 22% has been caused by wrong calculation of the exposure time or monitor units, 13% by inadequate review of patient's chart, 12% by mistakes in the anatomical area to be treated. The remaining 35% can be attributed to 17 different causes. The most common mistakes in brachytherapy were wrong activities of sources used for treatment (20%), inadequate procedures for placement of sources applicators (14%), mistakes in calculating the treatment time (12%), etc. The direct and contributing causes of radiological accidents have been deduced from each event, when it was possible and categorized into 9 categories: mistakes in procedures (30%), professional mistakes (17%), communication mistakes (15%), lack of training (8.5%), interpretation mistakes (7%), lack of supervision (6%), mistakes in judgement (6%), hardware failures (5%), software and other mistakes (5.5%). Three types of direct and contributing causes responsible for almost 62% of all accidents are directly connected to the quality assurance of treatment. The lessons learnt from the accidents are related to frequencies of direct and contributing factors and show that most of the accident are caused by lack, non-application of quality assurance (QA) procedures or by underestimating of QA procedures. The international system for collection of accidents and dissemination of lessons learnt from the different accidents, proposed by IAEA, can contribute to better practice in many radiotherapy departments. Most of the accidents could have been avoided, had a comprehensive QA programme been established and properly applied in all radiotherapy departments, whatever the size. (author)

Accident at Harrisburg

International Nuclear Information System (INIS)

1979-05-01

The course of events during the accident on 28 March 1979 at Three Mile Island-2 Reactor at Harrisburg, Pennsylvania, is described in detail. The effects (in the environment and within the safety containment) are described. The following points are then discussed: the possibility of a comparable accident occurring in the nuclear power stations in the German Federal Republic; the possibility of any point having been overlooked in the design of nuclear power stations in the Federal Republic; whether previous risk analyses are still valid; and how near the Three Mile Island reactor was to a core meltdown. Some conclusions are drawn. (U.K.)

Updating and maintaining the accident database.

CSIR Research Space (South Africa)

Jaku, EP

2001-03-01

Full Text Available in the analysis of the accident statistics. This normalization nullifies the effect of varying production levels during the period under review and of different reefs. This report covers the analyses carried out on data collected. The objectives of the analyses...

Accident tolerant clad material modeling by MELCOR: Benchmark for SURRY Short Term Station Black Out

International Nuclear Information System (INIS)

Wang, Jun; Mccabe, Mckinleigh; Wu, Lei; Dong, Xiaomeng; Wang, Xianmao; Haskin, Troy Christopher; Corradini, Michael L.

2017-01-01

Highlights: • Thermo-physical and oxidation kinetics properties calculation and analysis of FeCrAl. • Properties modelling of FeCrAl in MELCOR. • Benchmark calculation of Surry nuclear power plant. - Abstract: Accident tolerant fuel and cladding materials are being investigated to provide a greater resistance to fuel degradation, oxidation and melting if long-term cooling is lost in a Light Water Reactor (LWR) following an accident such as a Station Blackout (SBO) or Loss of Coolant Accident (LOCA). Researchers at UW-Madison are analyzing an SBO sequence and examining the effect of a loss of auxiliary feedwater (AFW) with the MELCOR systems code. Our research work considers accident tolerant cladding materials (e.g., FeCrAl alloy) and their effect on the accident behavior. We first gathered the physical properties of this alternative cladding material via literature review and compared it to the usual zirconium alloys used in LWRs. We then developed a model for the Surry reactor for a Short-term SBO sequence and examined the effect of replacing FeCrAl for Zircaloy cladding. The analysis uses MELCOR, Version 1.8.6 YR, which is developed by Idaho National Laboratory in collaboration with MELCOR developers at Sandia National Laboratories. This version allows the user to alter the cladding material considered, and our study examines the behavior of the FeCrAl alloy as a substitute for Zircaloy. Our benchmark comparisons with the Sandia National Laboratory’s analysis of Surry using MELCOR 1.8.6 and the more recent MELCOR 2.1 indicate good overall agreement through the early phases of the accident progression. When FeCrAl is substituted for Zircaloy to examine its performance, we confirmed that FeCrAl slows the accident progression and reduce the amount of hydrogen generated. Our analyses also show that this special version of MELCOR can be used to evaluate other potential ATF cladding materials, e.g., SiC as well as innovative coatings on zirconium cladding

Accident tolerant clad material modeling by MELCOR: Benchmark for SURRY Short Term Station Black Out

Energy Technology Data Exchange (ETDEWEB)

Wang, Jun, E-mail: jwang564@wisc.edu [College of Engineering, The University of Wisconsin-Madison, Madison 53706 (United States); Mccabe, Mckinleigh [College of Engineering, The University of Wisconsin-Madison, Madison 53706 (United States); Wu, Lei [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Dong, Xiaomeng [College of Engineering, The University of Wisconsin-Madison, Madison 53706 (United States); Wang, Xianmao [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Haskin, Troy Christopher [College of Engineering, The University of Wisconsin-Madison, Madison 53706 (United States); Corradini, Michael L., E-mail: corradini@engr.wisc.edu [College of Engineering, The University of Wisconsin-Madison, Madison 53706 (United States)

2017-03-15

Highlights: • Thermo-physical and oxidation kinetics properties calculation and analysis of FeCrAl. • Properties modelling of FeCrAl in MELCOR. • Benchmark calculation of Surry nuclear power plant. - Abstract: Accident tolerant fuel and cladding materials are being investigated to provide a greater resistance to fuel degradation, oxidation and melting if long-term cooling is lost in a Light Water Reactor (LWR) following an accident such as a Station Blackout (SBO) or Loss of Coolant Accident (LOCA). Researchers at UW-Madison are analyzing an SBO sequence and examining the effect of a loss of auxiliary feedwater (AFW) with the MELCOR systems code. Our research work considers accident tolerant cladding materials (e.g., FeCrAl alloy) and their effect on the accident behavior. We first gathered the physical properties of this alternative cladding material via literature review and compared it to the usual zirconium alloys used in LWRs. We then developed a model for the Surry reactor for a Short-term SBO sequence and examined the effect of replacing FeCrAl for Zircaloy cladding. The analysis uses MELCOR, Version 1.8.6 YR, which is developed by Idaho National Laboratory in collaboration with MELCOR developers at Sandia National Laboratories. This version allows the user to alter the cladding material considered, and our study examines the behavior of the FeCrAl alloy as a substitute for Zircaloy. Our benchmark comparisons with the Sandia National Laboratory’s analysis of Surry using MELCOR 1.8.6 and the more recent MELCOR 2.1 indicate good overall agreement through the early phases of the accident progression. When FeCrAl is substituted for Zircaloy to examine its performance, we confirmed that FeCrAl slows the accident progression and reduce the amount of hydrogen generated. Our analyses also show that this special version of MELCOR can be used to evaluate other potential ATF cladding materials, e.g., SiC as well as innovative coatings on zirconium cladding

Contrasting safety assessments of a runway incursion scenario: Event sequence analysis versus multi-agent dynamic risk modelling

International Nuclear Information System (INIS)

Stroeve, Sybert H.; Blom, Henk A.P.; Bakker, G.J.

2013-01-01

In the safety literature it has been argued, that in a complex socio-technical system safety cannot be well analysed by event sequence based approaches, but requires to capture the complex interactions and performance variability of the socio-technical system. In order to evaluate the quantitative and practical consequences of these arguments, this study compares two approaches to assess accident risk of an example safety critical sociotechnical system. It contrasts an event sequence based assessment with a multi-agent dynamic risk model (MA-DRM) based assessment, both of which are performed for a particular runway incursion scenario. The event sequence analysis uses the well-known event tree modelling formalism and the MA-DRM based approach combines agent based modelling, hybrid Petri nets and rare event Monte Carlo simulation. The comparison addresses qualitative and quantitative differences in the methods, attained risk levels, and in the prime factors influencing the safety of the operation. The assessments show considerable differences in the accident risk implications of the performance of human operators and technical systems in the runway incursion scenario. In contrast with the event sequence based results, the MA-DRM based results show that the accident risk is not manifest from the performance of and relations between individual human operators and technical systems. Instead, the safety risk emerges from the totality of the performance and interactions in the agent based model of the safety critical operation considered, which coincides very well with the argumentation in the safety literature.

A study on the operator's errors of commission (EOC) in accident scenarios of nuclear power plants: methodology development and application

Energy Technology Data Exchange (ETDEWEB)

Kim, Jae Whan; Jung, Won Dea; Park, Jin Kyun; Kang, Da Il

2003-04-01

As the concern on the operator's inappropriate interventions, the so-called Errors Of Commission (EOCs), that can exacerbate the plant safety has been raised, much of interest in the identification and analysis of EOC events from the risk assessment perspective has been increased. Also, one of the items in need of improvement for the conventional PSA and HRA that consider only the system-demanding human actions is the inclusion of the operator's EOC events into the PSA model. In this study, we propose a methodology for identifying and analysing human errors of commission that might be occurring from the failures in situation assessment and decision making during accident progressions given an initiating event. In order to achieve this goal, the following research items have been performed: Firstly, we analysed the error causes or situations contributed to the occurrence of EOCs in several incidents/accidents of nuclear power plants. Secondly, limitations of the advanced HRAs in treating EOCs were reviewed, and a requirement for a new methodology for analysing EOCs was established. Thirdly, based on these accomplishments a methodology for identifying and analysing EOC events inducible from the failures in situation assessment and decision making was proposed and applied to all the accident sequences of YGN 3 and 4 NPP which resulted in the identification of about 10 EOC situations.

Injury protection and accident causation parameters for vulnerable road users based on German In-Depth Accident Study GIDAS.

Science.gov (United States)

Otte, Dietmar; Jänsch, Michael; Haasper, Carl

2012-01-01

Within a study of accident data from GIDAS (German In-Depth Accident Study), vulnerable road users are investigated regarding injury risk in traffic accidents. GIDAS is the largest in-depth accident study in Germany. Due to a well-defined sampling plan, representativeness with respect to the federal statistics is also guaranteed. A hierarchical system ACASS (Accident Causation Analysis with Seven Steps) was developed in GIDAS, describing the human causation factors in a chronological sequence. The accordingly classified causation factors - derived from the systematic of the analysis of human accident causes ("7 steps") - can be used to describe the influence of accident causes on the injury outcome. The bases of the study are accident documentations over ten years from 1999 to 2008 with 8204 vulnerable road users (VRU), of which 3 different groups were selected as pedestrians n=2041, motorcyclists n=2199 and bicyclists n=3964, and analyzed on collisions with cars and trucks as well as vulnerable road users alone. The paper will give a description of the injury pattern and injury mechanisms of accidents. The injury frequencies and severities are pointed out considering different types of VRU and protective measures of helmet and clothes of the human body. The impact points are demonstrated on the car, following to conclusion of protective measures on the vehicle. Existing standards of protection devices as well as interdisciplinary research, including accident and injury statistics, are described. With this paper, a summarization of the existing possibilities on protective measures for pedestrians, bicyclists and motorcyclists is given and discussed by comparison of all three groups of vulnerable road users. Also the relevance of special impact situations and accident causes mainly responsible for severe injuries are pointed out, given the new orientation of research for the avoidance and reduction of accident patterns. 2010 Elsevier Ltd. All rights reserved.

Investigation of SAM measures during selected MBLOCA sequences along with Station Blackout in a generic Konvoi PWR using ASTECV2.0

International Nuclear Information System (INIS)

Gómez-García-Toraño, Ignacio; Sánchez Espinoza, Víctor Hugo; Stieglitz, Robert

2017-01-01

Highlights: • Reflooding is investigated for selected MBLOCA sequences in a Konvoi PWR using ASTEC. • After SBO, there is a grace time of 40 min up to the detection of a CET = 650 °C. • Major core damage prevented if reflood is launched at CET = 650 °C with 25-40 kg/s. • Values depend on the time when the plant is struck by Station Blackout. • Vessel failure cannot be prevented if supplied mass flow rates are lower than 10 kg/s. - Abstract: The Fukushima accidents have shown that further improvement of Severe Accident Management Guidelines (SAMGs) is necessary for the current fleet of Light Water Reactors. The elaboration of SAMGs requires a broad database of deterministic analyses performed with state-of-the art simulation tools. Within this work, the ASTECV2.0 integral severe accident code is used to study the efficiency of core reflooding (as a SAM measure) during postulated Medium Break LOCA (MBLOCA) scenarios in a German Konvoi PWR. In a first step, the progression of selected MBLOCA sequences without SAM measures has been analysed. The sequences postulate a break in the cold leg of the pressurizer loop and the total loss of AC power at a given stage of the accident. Results show the existence of a 40 min grace time up to the detection of a Core Exit Temperature (CET) of 650 °C providing that the AC power has been maintained at least 1 h after SCRAM. In a second step, an extensive analysis on core reflooding has been carried out. The sequences assume that the plant remains in Station Blackout (SBO) and that reflooding occurs at different times with different mobile pumps. The simulations yield the following results: • Reflooding mass flow rates above 60 kg/s have to be supplied as soon as the CET exceeds 650 °C in order to prevent core melting. • Reflooding mass flow rates ranging from 25–40 kg/s at CET = 650 °C mitigate the accident without major core damage depending on when the plant enters in SBO. • Reflooding mass flow rates lower

Sensitivity studies of air ingress accidents in modular HTGRs

International Nuclear Information System (INIS)

Ball, Syd; Richards, Matt; Shepelev, Sergey

2008-01-01

Postulated air ingress accidents, while of very low probability in a modular high-temperature gas-cooled reactor (HTGR), are of considerable interest to the plant designer, operator, and regulator because of the possibility that the core could sustain significant damage under some circumstances. Sensitivity analyses are described that cover a wide spectrum of conditions affecting outcomes of the postulated accident sequences, for both prismatic and pebble-bed core designs. The major factors affecting potential core damage are the size and location of primary system leaks, flow path resistances, the core temperature distribution, and the long-term availability of oxygen in the incoming gas from a confinement building. Typically, all the incoming oxygen entering the core area is consumed within the reactor vessel, so it is more a matter of where, not whether, oxidation occurs. An air ingress model with example scenarios and means for mitigating damage are described. Representative designs of modular HTGRs included here are a 400-MW(th) pebble-bed reactor (PBR), and a 600-MW(th) prismatic-core modular reactor (PMR) design such as the gas-turbine modular helium reactor (GT-MHR)

NPP Krsko Severe Accident Management Guidelines Implementation

International Nuclear Information System (INIS)

Basic, I.; Krajnc, B.; Bilic-Zabric, T.; Spiler, J.

2002-01-01

Severe Accident Management is a framework to identify and implement the Emergency Response Capabilities that can be used to prevent or mitigate severe accidents and their consequences. The USA NRC has indicated that the development of a licensee plant specific accident management program will be required in order to close out the severe accident regulatory issue (Ref. SECY-88-147). Generic Letter 88-20 ties the Accident management Program to IPE for each plant. The SECY-89-012 defines those actions taken during the course of an accident by the plant operating and technical staff to: 1) prevent core damage, 2) terminate the progress of core damage if it begins and retain the core within the reactor vessel, 3) maintain containment integrity as long as possible, and 4) minimize offsite releases. The subject of this paper is to document the severe accident management activities, which resulted in a plant specific Severe Accident Management Guidelines implementation. They have been developed based on the Krsko IPE (Individual Plant Examination) insights, Generic WOG SAMGs (Westinghouse Owners Group Severe Accident Management Guidances) and plant specific documents developed within this effort. Among the required plant specific actions the following are the most important ones: Identification and documentation of those Krsko plant specific severe accident management features (which also resulted from the IPE investigations). The development of the Krsko plant specific background documents (Severe Accident Plant Specific Strategies and SAMG Setpoint Calculation). Also, paper discusses effort done in the areas of NPP Krsko SAMG review (internal and external ), validation on Krsko Full Scope Simulator (Severe Accident sequences are simulated by MAAP4 in real time) and world 1st IAEA Review of Accident Management Programmes (RAMP). (author)

Accident at the Three Mile Island Nuclear Power Plant

International Nuclear Information System (INIS)

Bajusz, J.; Vamos, G.

1979-01-01

A short description of the TMI power plant is given. The course of events leading to the reactor accident and that of the first two weeks is described. The effect on the environment is estimated. The reasons and consequences of the accident are analysed. The probability of such an accident at the Paks Nuclear Power Plant is estimated. (R.J.)

Identification of important phenomena under sodium fire accidents based on PIRT process with factor analysis in sodium-cooled fast reactor

International Nuclear Information System (INIS)

Aoyagi, Mitsuhiro; Uchibori, Akihiro; Kikuchi, Shin; Takata, Takashi; Ohno, Shuji; Ohshima, Hiroyuki

2016-01-01

The PIRT (Phenomena Identification and Ranking Table) process is an effective method to identify key phenomena involved in safety issues in nuclear power plants. The present PIRT process is aimed to validate sodium fire analysis codes. Because a sodium fire accident in sodium-cooled fast reactor (SFR) involves complex phenomena, various figures of merit (FOMs) could exist in this PIRT process. In addition, importance evaluation of phenomena for each FOM should be implemented in an objective manner under the PIRT process. This paper describes the methodology for specification of FOMs, identification of associated phenomena and importance evaluation of each associated phenomenon in order to complete a ranking table of important phenomena involved in a sodium fire accident in an SFR. The FOMs were specified through factor analysis in this PIRT process. Physical parameters to be quantified by a sodium fire analysis code were identified by considering concerns resulting from sodium fire in the factor analysis. Associated phenomena were identified through the element- and sequence-based phenomena analyses as is often conducted in PIRT processes. Importance of each associated phenomenon was evaluated by considering the sequence-based analysis of associated phenomena correlated with the FOMs. Then, we complete the ranking table through the factor and phenomenon analyses. (author)

Lessons from the Fukushima nuclear power accident

International Nuclear Information System (INIS)

Hatamura, Yotaro

2013-01-01

Through the investigation of the Fukushima Nuclear Power Accident as the chairman of the related Government's Committee, many things had been considered. Essence of the accident could be not only what occurred in the Fukushima nuclear power station, but also dispersed radioactive materials forced many residents to move and not to be returned. Such events as indication errors of water level meter occurring in severe accident could no be thought and remote mechanical operation of valves under high radiation environment were not prepared. Contamination by radioactive clouds caused the evacuation of residents for a long period. Lessons learned from the accident were described such as; (1) the verification of the road to failure connecting selected accident sequence and road to success with another supposed choice, (2) considering what might occur and then what should be needed on the contrary, (3) nuclear power, if should be continued, should be used with the premise of its hazards, and (4) advise to nuclear engineer for adequate information dissemination and technical explanation to the public and keeping nuclear technologies alive. (T. Tanaka)

Improvement of severe accident analysis method for KSNP

Energy Technology Data Exchange (ETDEWEB)

Park, Jae Hong [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of); Cho, Song Won; Cho, Youn Soo [Korea Radiation Technology Institute Co., Taejon (Korea, Republic of)

2002-03-15

The objective of this study is preparation of MELCOR 1.8.5 input deck for KSNP and simulation of some major severe accidents. The contents of this project are preparation of MELCOR 1.8.5 base input deck for KSNP to understand severe accident phenomena and to assess severe accident strategy, preparation of 20 cell containment input deck to simulate the distribution of hydrogen and fission products in containment, simulation of some major severe accident scenarios such as TLOFW, SBO, SBLOCA, MBLOCA, and LBLOCA. The method for MELCOR 1.8.5 input deck preparation can be used to prepare the input deck for domestic PWRs and to simulate severe accident experiments such as ISP-46. Information gained from analyses of severe accidents may be helpful to set up the severe accident management strategy and to develop regulatory guidance.

Work-related accidents and occupational diseases in veterinarians and their staff.

Science.gov (United States)

Nienhaus, Albert; Skudlik, Christoph; Seidler, Andreas

2005-04-01

We assessed the occupational hazards in veterinary practice by analysing accident insurance data in order to stimulate strategies to prevent occupational accidents and diseases in veterinarians and their staff. Approximately 10,000 veterinary practices comprising about 27,500 veterinarians and their staff are covered by the Institution of Statutory Accident Insurance of the Health and Welfare Service (BGW). Each year about 2,000 accident and occupational disease claims are filed by these veterinarians and their staff. The claims for the 5-year period from 1998 to 2002 are analysed in this paper. For 2002, the incidence rate for accidents in the workplace was 105.4 per 1,000 full-time workers, a rate 2.9-times higher than for general practitioners of human medicine. When only severe accidents resulting in a loss of work time of more than 3 days were analysed, the relative risk increased to 9.2. Approximately 66% of the reported accidents are due to scratches, bites, or kicks from animals. Claims of occupational disease are filed 2.7-times more often by veterinarians and their staff than by general practitioners and their staff. The occupational diseases filed most often concern the skin (39%), followed by allergic respiratory diseases (30.5%), and infectious diseases (19.1%). Prevention strategies for veterinarians should focus on accidents caused by animals. The prevention of occupational diseases should focus on skin diseases, respiratory disease, and infections.

On preparation for accident management in LWR power stations

International Nuclear Information System (INIS)

1996-01-01

Nuclear Safety Commission received the report from Reactor Safety General Examination Committee which investigated the policy of executing the preparation for accident management. The basic policy on the preparation for accident management was decided by Nuclear Safety Commission in May, 1992. This Examination Committee investigated the policy of executing the preparation for accident management, which had been reported from the administrative office, and as the result, it judged the policy as adequate, therefore, the report is made. The course to the foundation of subcommittee is reported. The basic policy of the examination on accident management by the subcommittee conforming to the decision by Nuclear Safety Commission, the measures of accident management which were extracted for BWR and PWR facilities, the examination of the technical adequacy of selecting accident sequences in BWR and PWR facilities and the countermeasures to them, the adequacy of the evaluation of the possibility of executing accident management measures and their effectiveness and the adequacy of the evaluation of effect to existing safety functions, the preparation of operation procedure manual, and education and training plan are reported. (K.I.)

Accident and safety analyses for the HTR-modul. Partial project 1: Computer codes for system behaviour calculation. Final report. Pt. 2

International Nuclear Information System (INIS)

Lohnert, G.; Becker, D.; Dilcher, L.; Doerner, G.; Feltes, W.; Gysler, G.; Haque, H.; Kindt, T.; Kohtz, N.; Lange, L.; Ragoss, H.

1993-08-01

The project encompasses the following project tasks and problems: (1) Studies relating to complete failure of the main heat transfer system; (2) Pebble flow; (3) Development of computer codes for detailed calculation of hypothetical accidents; (a) the THERMIX/RZKRIT temperature buildup code (covering a.o. a variation to include exothermal heat sources); (b) the REACT/THERMIX corrosion code (variation taking into account extremely severe air ingress into the primary loop); (c) the GRECO corrosion code (variation for treating extremely severe water ingress into the primary loop); (d) the KIND transients code (for treating extremely fast transients during reactivity incidents. (4) Limiting devices for safety-relevant quantities. (5) Analyses relating to hypothetical accidents. (a) hypothetical air ingress; (b) effects on the fuel particles induced by fast transients. The problems of the various tasks are defined in detail and the main results obtained are explained. The contributions reporting the various project tasks and activities have been prepared for separate retrieval from the database. (orig./HP) [de

Accident and safety analyses for the HTR-modul. Partial project 1: Computer codes for system behaviour calculation. Final report. Pt. 1

International Nuclear Information System (INIS)

Lohnert, G.; Becker, D.; Dilcher, L.; Doerner, G.; Feltes, W.; Gysler, G.; Haque, H.; Kindt, T.; Kohtz, N.; Lange, L.; Ragoss, H.

1993-08-01

The project encompasses the following project tasks and problems: (1) Studies relating to complete failure of the main heat transfer system; (2) Pebble flow; (3) Development of computer codes for detailed calculation of hypothetical accidents; (a) the THERMIX/RZKRIT temperature buildup code (covering a.o. a variation to include exothermal heat sources); (b) the REACT/THERMIX corrosion code (variation taking into account extremely severe air ingress into the primary loop); (c) the GRECO corrosion code (variation for treating extremely severe water ingress into the primary loop); (d) the KIND transients code (for treating extremely fast transients during reactivity incidents. (4) Limiting devices for safety-relevant quantities. (5) Analyses relating to hypothetical accidents. (a) hypothetical air ingress; (b) effects on the fuel particles induced by fast transients. The problems of the various tasks are defined in detail and the main results obtained are explained. The contributions reporting the various project tasks and activities have been prepared for separate retrieval from the database. (orig./HP) [de

The effect of roundabout design features on cyclist accident rate

DEFF Research Database (Denmark)

Hels, Tove; Orozova-Bekkevold, Ivanka

2007-01-01

Roundabouts are known to result in fewer traffic accidents than traditional intersections. However, this is to a lesser degree true for bicycles than for vehicles. In this paper, we aimed at establishing statistical relationships through Poisson regression and logistic regression analyses between...... was age of the roundabout-older roundabouts related to more accidents and higher accident probability. Excluding 48 single cyclist accidents strengthened the relationship between accidents on one hand and vehicle and cyclist volume and potential vehicle speed on the other. This stresses the significance...

Accidents - Chernobyl accident

International Nuclear Information System (INIS)

2004-01-01

This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

PWR pressure vessel integrity during overcooling accidents

International Nuclear Information System (INIS)

Cheverton, R.D.

1981-01-01

Pressurized water reactors are susceptible to certain types of hypothetical accidents that under some circumstances, including operation of the reactor beyond a critical time in its life, could result in failure of the pressure vessel as a result of propagation of crack-like defects in the vessel wall. The accidents of concern are those that result in thermal shock to the vessel while the vessel is subjected to internal pressure. Such accidents, referred to as pressurized thermal shock or overcooling accidents (OCA), include a steamline break, small-break LOCA, turbine trip followed by stuck-open bypass valves, the 1978 Rancho Seco and the TMI accidents and many other postulated and actual accidents. The source of cold water for the thermal shock is either emergency core coolant or the normal primary-system coolant. ORNL performed fracture-mechanics calculations for a steamline break in 1978 and for a turbine-trip case in 1980 and concluded on the basis of the results that many more such calculations would be required. To meet the expected demand in a realistic way a computer code, OCA-I, was developed that accepts primary-system temperature and pressure transients as input and then performs one-dimensional thermal and stress analyses for the wall and a corresponding fracture-mechanics analysis for a long axial flaw. The code is briefly described, and its use in both generic and specific plant analyses is discussed

Reactor accidents of four decades

International Nuclear Information System (INIS)

Szabo, Z.

1982-11-01

The report covers the period between 1942 and June 30, 1982. A detailed description and a comparative analysis of reactor accidents and chemical-processing-plant excursions are presented. The analysis takes into account the following points: causes (design, maintenance, operation); events (initiating event and sequence of events); consequences (environmental impacts, personnel effects and equipment damages). (author)

An application of probabilistic safety assessment methods to model aircraft systems and accidents

Energy Technology Data Exchange (ETDEWEB)

Martinez-Guridi, G.; Hall, R.E.; Fullwood, R.R.

1998-08-01

A case study modeling the thrust reverser system (TRS) in the context of the fatal accident of a Boeing 767 is presented to illustrate the application of Probabilistic Safety Assessment methods. A simplified risk model consisting of an event tree with supporting fault trees was developed to represent the progression of the accident, taking into account the interaction between the TRS and the operating crew during the accident, and the findings of the accident investigation. A feasible sequence of events leading to the fatal accident was identified. Several insights about the TRS and the accident were obtained by applying PSA methods. Changes proposed for the TRS also are discussed.

Analysis of effects of calandria tube uncovery under severe accident conditions in CANDU reactors

International Nuclear Information System (INIS)

Rogers, J.T.; Currie, T.C.; Atkinson, J.C.; Dick, R.

1983-01-01

A study is being undertaken for the Atomic Energy Control Board to assess the thermal and hydraulic behaviour of CANDU reactor cores under accident conditions more severe than those normally considered in the licensing process. In this paper, we consider the effects on a coolant channel of the uncovery of a calandria tube by moderator boil-off following a LOCA in a Bruce reactor unit in which emergency cooling is ineffective and the moderator heat sink is impaired by the failure of the moderator cooling system. Calandria tube uncovery and its immediate consequences, as described here, constitute only one part of the entire accident sequence. Other aspects of this sequence as well as results of the analysis of the other accident sequences studied will be described in the final report on the project and in later papers

MELCOR Severe Accident Analysis on the SMART Reactor

International Nuclear Information System (INIS)

Kim, Tae Woon; Jin, Young Ho; Kim, Young In; Kim, Keung Koo; Wang, Ziao; Revankar, Shripad

2014-01-01

A severe accident is analyzed for Korea SMR reactor, SMART. Core melt down sequences are analyzed for SMART reactor core using MELCOR version 1.8.5. MELCOR is developed by Sandia National Laboratory for US NRC for the simulation of severe accidents in nuclear power plants. Two cases are simulated here and compared between them; one is the case for core having 3 concentric rings and the other is the case for core having 5 concentric rings. One inch break LOCA scenario is simulated and compared between these two core models. Time sequences for the thermal hydraulic behaviors of RPV and thermal heatup behaviors of reactor core are explained in graphically. Thermal hydraulic behavior such as the change of pressure, level, mass, and temperature of RPV is explained. Thermal heatup behavior of reactor core such as oxidation of cladding, hydrogen generation, core slumping down to lower plenum, and finally creep rupture of PRV lower head is explained. Engineered safety features such as safety injection systems (SIS), and Passive residual heat removal systems (PHRS), etc. are assumed to be not working. One inch break of severe accident is simulated on Korean SMR (SMART) Integral PWR with MELCOR code version 1.8.5. Core melt progression and lower head failure time is very slow compared to other commercial reactors. Simulation on 3 and 5 radial rings core models gives very similar pattern in core cell failure timings. Other various accident scenarios (for example, SBO in Fukushima) will be tried further. Containment behaviors and source term behaviors in severe accident conditions will be analyzed in future

Severe accident approach - final report. Evaluation of design measures for severe accident prevention and consequence mitigation

International Nuclear Information System (INIS)

Tentner, A.M.; Parma, E.; Wei, T.; Wigeland, R.

2010-01-01

An important goal of the US DOE reactor development program is to conceptualize advanced safety design features for a demonstration Sodium Fast Reactor (SFR). The treatment of severe accidents is one of the key safety issues in the design approach for advanced SFR systems. It is necessary to develop an in-depth understanding of the risk of severe accidents for the SFR so that appropriate risk management measures can be implemented early in the design process. This report presents the results of a review of the SFR features and phenomena that directly influence the sequence of events during a postulated severe accident. The report identifies the safety features used or proposed for various SFR designs in the US and worldwide for the prevention and/or mitigation of Core Disruptive Accidents (CDA). The report provides an overview of the current SFR safety approaches and the role of severe accidents. Mutual understanding of these design features and safety approaches is necessary for future collaborations between the US and its international partners as part of the GEN IV program. The report also reviews the basis for an integrated safety approach to severe accidents for the SFR that reflects the safety design knowledge gained in the US during the Advanced Liquid Metal Reactor (ALMR) and Integral Fast Reactor (IFR) programs. This approach relies on inherent reactor and plant safety performance characteristics to provide additional safety margins. The goal of this approach is to prevent development of severe accident conditions, even in the event of initiators with safety system failures previously recognized to lead directly to reactor damage.

Severe accident approach - final report. Evaluation of design measures for severe accident prevention and consequence mitigation.

Energy Technology Data Exchange (ETDEWEB)

Tentner, A. M.; Parma, E.; Wei, T.; Wigeland, R.; Nuclear Engineering Division; SNL; INL

2010-03-01

An important goal of the US DOE reactor development program is to conceptualize advanced safety design features for a demonstration Sodium Fast Reactor (SFR). The treatment of severe accidents is one of the key safety issues in the design approach for advanced SFR systems. It is necessary to develop an in-depth understanding of the risk of severe accidents for the SFR so that appropriate risk management measures can be implemented early in the design process. This report presents the results of a review of the SFR features and phenomena that directly influence the sequence of events during a postulated severe accident. The report identifies the safety features used or proposed for various SFR designs in the US and worldwide for the prevention and/or mitigation of Core Disruptive Accidents (CDA). The report provides an overview of the current SFR safety approaches and the role of severe accidents. Mutual understanding of these design features and safety approaches is necessary for future collaborations between the US and its international partners as part of the GEN IV program. The report also reviews the basis for an integrated safety approach to severe accidents for the SFR that reflects the safety design knowledge gained in the US during the Advanced Liquid Metal Reactor (ALMR) and Integral Fast Reactor (IFR) programs. This approach relies on inherent reactor and plant safety performance characteristics to provide additional safety margins. The goal of this approach is to prevent development of severe accident conditions, even in the event of initiators with safety system failures previously recognized to lead directly to reactor damage.

Formalisation des bases méthodologiques et conceptuelles d'une analyse spatiale des accidents de la route

Directory of Open Access Journals (Sweden)

Florence Huguenin Richard

1999-06-01

Full Text Available Cet article pose les bases méthodologiques et conceptuelles d’une analyse spatiale du risque routier. L’étude de ce phénomène requiert une masse importante de données qui décrivent différentes dimensions de l’accident et qui peuvent être gérées dans un système d’information géographique. Elle demande aussi une réflexion méthodologique sur la cartographie du risque, les échelles d’observation, l’agrégation de données qualitatives et quantitatives, l’utilisation de méthodes statistiques adaptées au risque routier et l'intégration de l’espace comme facteur d’insécurité.

Risk Analysis of Fukushima Accident using MACCS2

Energy Technology Data Exchange (ETDEWEB)

Lee, Seunghee; Kim, Juyoul; Kim, Sukhoon; Kim, Juyub [FNC Technology Co. Ltd., Yongin (Korea, Republic of)

2014-05-15

It has been three years since Fukushima Daiichi accident had occurred. Many efforts have been done for a restoration, however, radioactive materials are still released resulting in a crucial additional damage to a human health and economics and the scale of damage is not much evaluated. Therefore, an estimation of damage degree caused by the released radioactive materials right after a nuclear accident is essential to cope with additional radioactive problems. Here, we report the risk analysis of Fukushima Dai-ichi accident using MELCOR Accident Consequence Code System 2 (MACCS2), which is the Nuclear Regulatory Commission's (NRC's) code for evaluating off-site consequences. It is used in level-3 Probabilistic Risk Analyses (PRA), for planning purposes, for cost-benefit analyses and so on. The purpose of this study is to estimate radiological doses and health risks of Fukushima Daiichi accident through short- and long-term of lifetime using MACCS2. In summary, the health risk for inhabitants near Fukushima Daiichi NPP has been evaluated by considering the long term radiation effect using MACCS2 code. The result indicates that the occurrence and death rate of the cancer have been increased by the radioactive materials released from Fukushima Daiichi accident. The result obtained in this study may provide new insights for taking action after the nuclear reactor accident to mitigate the released radioactive materials and to prepare the countermeasure.

Preliminary Accident Analyses for Conversion of the Massachusetts Institute of Technology Reactor (MITR) from Highly Enriched to Low Enriched Uranium

Energy Technology Data Exchange (ETDEWEB)

Dunn, Floyd E. [Argonne National Lab. (ANL), Argonne, IL (United States); Olson, Arne P. [Argonne National Lab. (ANL), Argonne, IL (United States); Wilson, Erik H. [Argonne National Lab. (ANL), Argonne, IL (United States); Sun, Kaichao S. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Newton, Jr., Thomas H. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Hu, Lin-wen [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

2013-09-30

The Massachusetts Institute of Technology Reactor (MITR-II) is a research reactor in Cambridge, Massachusetts designed primarily for experiments using neutron beam and in-core irradiation facilities. It delivers a neutron flux comparable to current LWR power reactors in a compact 6 MW core using Highly Enriched Uranium (HEU) fuel. In the framework of its non-proliferation policies, the international community presently aims to minimize the amount of nuclear material available that could be used for nuclear weapons. In this geopolitical context most research and test reactors, both domestic and international, have started a program of conversion to the use of LEU fuel. A new type of LEU fuel based on an alloy of uranium and molybdenum (U-Mo) is expected to allow the conversion of U.S. domestic high performance reactors like MITR. This report presents the preliminary accident analyses for MITR cores fueled with LEU monolithic U-Mo alloy fuel with 10 wt% Mo. Preliminary results demonstrate adequate performance, including thermal margin to expected safety limits, for the LEU accident scenarios analyzed.

Feasibility study on the rod ejection accident analysis with RETRAN-MASTER code system

International Nuclear Information System (INIS)

Kim, Y. H.; Lee, C. S.

2003-01-01

KEPRI has been developed the in-house methodology for non-LOCA safety analyses based on the codes and methodologies of vendors and EPRI. Using the methodology, the rod ejection accident, which is classified into the generic accident analysis category of reactivity insertion accident in primary system, has been analyzed with RETRAN-MASTER code system. And the feasibility of the coupled code system has been verified by the review of the results. Furthermore, to assess the important parameters to the accident, the sensitivity analyses have been carried out over some parameters

Development of instrumentation systems for severe accidents. 4. New accident tolerant in-containment pressure transducer for containment pressure monitoring system

International Nuclear Information System (INIS)

Oba, Masato; Teruya, Kuniyuki; Yoshitsugu, Makoto; Ikeuchi, Takeshi

2015-01-01

The accident at Tokyo Electric Power Company's Fukushima Dai-ichi Nuclear Power Plant (TF-1 accident) caused severe situations and resulted in a difficulty in measuring important parameters for monitoring plant conditions. Therefore, we have studied the TF-1 accident to select the important parameters that should be monitored at the severe accident and are developing the Severe Accident Instrumentations and Monitoring Systems that could measure the parameters in severe accident conditions. Mitsubishi Heavy Industries, LTD (MHI) developed a new accident tolerant containment pressure monitoring system and demonstrated that the monitoring system could endure extremely harsh environmental conditions that envelop severe accident environmental conditions inside a containment such as maximum operating temperature of up to 300degC and total integrated dose (TID) of 1 MGy gamma. The new containment pressure monitoring system comprises of a strain gage type pressure transducer and a mineral insulated (MI) cable with ceramic connectors, which are located in the containment, and a strain measuring amplifier located outside the containment. Less thermal and radiation degradation is achieved because of minimizing use of organic materials for in-containment equipment such as the transducer and connectors. Several tests were performed to demonstrate the performance and capability of the in-containment equipment under severe accident environmental conditions and the major steps in this testing were run in the following test sequences: (1) the baseline functional tests (e.g., repeatability, non-linearity, hysteresis, and so on) under normal conditions, (2) accident radiation testing, (3) seismic testing, and (4) steam/temperature test exposed to simulated severe accident environmental conditions. The test results demonstrate that the new pressure transducer can endure the simulated severe accident conditions. (author)

Comparative analyses of two Geraniaceae transcriptomes using next-generation sequencing.

Science.gov (United States)

Zhang, Jin; Ruhlman, Tracey A; Mower, Jeffrey P; Jansen, Robert K

2013-12-29

Organelle genomes of Geraniaceae exhibit several unusual evolutionary phenomena compared to other angiosperm families including accelerated nucleotide substitution rates, widespread gene loss, reduced RNA editing, and extensive genomic rearrangements. Since most organelle-encoded proteins function in multi-subunit complexes that also contain nuclear-encoded proteins, it is likely that the atypical organellar phenomena affect the evolution of nuclear genes encoding organellar proteins. To begin to unravel the complex co-evolutionary interplay between organellar and nuclear genomes in this family, we sequenced nuclear transcriptomes of two species, Geranium maderense and Pelargonium x hortorum. Normalized cDNA libraries of G. maderense and P. x hortorum were used for transcriptome sequencing. Five assemblers (MIRA, Newbler, SOAPdenovo, SOAPdenovo-trans [SOAPtrans], Trinity) and two next-generation technologies (454 and Illumina) were compared to determine the optimal transcriptome sequencing approach. Trinity provided the highest quality assembly of Illumina data with the deepest transcriptome coverage. An analysis to determine the amount of sequencing needed for de novo assembly revealed diminishing returns of coverage and quality with data sets larger than sixty million Illumina paired end reads for both species. The G. maderense and P. x hortorum transcriptomes contained fewer transcripts encoding the PLS subclass of PPR proteins relative to other angiosperms, consistent with reduced mitochondrial RNA editing activity in Geraniaceae. In addition, transcripts for all six plastid targeted sigma factors were identified in both transcriptomes, suggesting that one of the highly divergent rpoA-like ORFs in the P. x hortorum plastid genome is functional. The findings support the use of the Illumina platform and assemblers optimized for transcriptome assembly, such as Trinity or SOAPtrans, to generate high-quality de novo transcriptomes with broad coverage. In addition

Consideration of severe accidents in design of advanced WWER reactors

International Nuclear Information System (INIS)

Fedorov, V.G.; Rogov, M.F.; Podshibyakin, A.K.; Fil, N.S.; Volkov, B.E.; Semishkin, V.P.

1998-01-01

Severe accident related requirements formulated in General Regulations for Nuclear Power Plant Safety (OPB-88), in Nuclear Safety Regulations for Nuclear Power Stations' Reactor Plants (PBYa RU AS-89) and in other NPP nuclear and radiation guides of the Russian Gosatomnadzor are analyzed. In accordance with these guides analyses of beyond design basis accidents should be performed in the reactor plant design. Categorization of beyond design basis accidents leading to severe accidents should be made on occurrence probability and severity of consequences. Engineered features and measures intended for severe accident management should be provided in reactor plant design. Requirements for severe accident analyses and for development of measures for severe accident management are determined. Design philosophy and proposed engineered measures for mitigation of severe accidents and decrease of radiation releases are demonstrated using examples of large, WWER-1000 (V-392), and medium size WWER-640 (V-407) reactor plant designs. Mitigation of severe accidents and decrease of radiation releases are supposed to be conducted on basis of consistent realization of the defense in depth concept relating to application of a system of barriers on the path of spreading of ionizing radiation and radioactive materials to the environment and a set of engineered measures protecting these barriers and retaining their effectiveness. Status of fulfilled by OKB Gidropress and other Russian organizations experimental and analytical investigations of severe accident phenomena supporting design decisions and severe accident management procedures is described. Status of the works on retention of core melt inside the WWER-640 reactor vessel is also characterized

Core fusion accidents in nuclear power reactors. Knowledge review

International Nuclear Information System (INIS)

Bentaib, Ahmed; Bonneville, Herve; Clement, Bernard; Cranga, Michel; Fichot, Florian; Koundy, Vincent; Meignen, Renaud; Corenwinder, Francois; Leteinturier, Denis; Monroig, Frederique; Nahas, Georges; Pichereau, Frederique; Van-Dorsselaere, Jean-Pierre; Cenerino, Gerard; Jacquemain, Didier; Raimond, Emmanuel; Ducros, Gerard; Journeau, Christophe; Magallon, Daniel; Seiler, Jean-Marie; Tourniaire, Bruno

2013-01-01

This reference document proposes a large and detailed review of severe core fusion accidents occurring in nuclear power reactors. It aims at presenting the scientific aspects of these accidents, a review of knowledge and research perspectives on this issue. After having recalled design and operation principles and safety principles for reactors operating in France, and the main studied and envisaged accident scenarios for the management of severe accidents in French PWRs, the authors describe the physical phenomena occurring during a core fusion accident, in the reactor vessel and in the containment building, their sequence and means to mitigate their effects: development of the accident within the reactor vessel, phenomena able to result in an early failure of the containment building, phenomena able to result in a delayed failure with the corium-concrete interaction, corium retention and cooling in and out of the vessel, release of fission products. They address the behaviour of containment buildings during such an accident (sizing situations, mechanical behaviour, bypasses). They review and discuss lessons learned from accidents (Three Mile Island and Chernobyl) and simulation tests (Phebus-PF). A last chapter gives an overview of software and approaches for the numerical simulation of a core fusion accident

Accident precursors, near misses, and warning signs: Critical review and formal definitions within the framework of Discrete Event Systems

International Nuclear Information System (INIS)

Saleh, Joseph H.; Saltmarsh, Elizabeth A.; Favarò, Francesca M.; Brevault, Loïc

2013-01-01

An important consideration in safety analysis and accident prevention is the identification of and response to accident precursors. These off-nominal events are opportunities to recognize potential accident pathogens, identify overlooked accident sequences, and make technical and organizational decisions to address them before further escalation can occur. When handled properly, the identification of precursors provides an opportunity to interrupt an accident sequence from unfolding; when ignored or missed, precursors may only provide tragic proof after the fact that an accident was preventable. In this work, we first provide a critical review of the concept of precursor, and we highlight important features that ought to be distinguished whenever accident precursors are discussed. We address for example the notion of ex-ante and ex-post precursors, identified for postulated and instantiated (occurred) accident sequences respectively, and we discuss the feature of transferability of precursors. We then develop a formal (mathematical) definition of accident precursors as truncated accident sequences within the modeling framework of Discrete Event Systems. Additionally, we examine the related notions of “accident pathogens” as static or lurking adverse conditions that can contribute to or aggravate an accident, as well as “near misses”, “warning signs” and the novel concept of “accident pathway”. While these terms are within the same linguistic neighborhood as “accident precursors”, we argue that there are subtle but important differences between them and recommend that they not be used interchangeably for the sake of accuracy and clarity of communication within the risk and safety community. We also propose venues for developing quantitative importance measures for accident precursors, similar to component importance measures in reliability engineering. Our objective is to establish a common understanding and clear delineation of these terms, and

Application of the Severe Accident Code ATHLET-CD. Coolant injection to primary circuit of a PWR by mobile pump system in case of SBLOCA severe accident scenario

Energy Technology Data Exchange (ETDEWEB)

Jobst, Matthias; Wilhelm, Polina; Kliem, Soeren; Kozmenkov, Yaroslav [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Reactor Safety

2017-06-01

The improvement of the safety of nuclear power plants is a continuously on-going process. The analysis of transients and accidents is an important research topic, which significantly contributes to safety enhancements of existing power plants. In case of an accident with multiple failures of safety systems, core uncovery and heat-up can occur. In order to prevent the accident to turn into a severe one or to mitigate the consequences of severe accidents, different accident management measures can be applied. By means of numerical analyses performed with the compute code ATHLET-CD, the effectiveness of coolant injection with a mobile pump system into the primary circuit of a PWR was studied. According to the analyses, such a system can stop the melt progression if it is activated prior to 10 % of total core is molten.

Application of the Severe Accident Code ATHLET-CD. Coolant injection to primary circuit of a PWR by mobile pump system in case of SBLOCA severe accident scenario

International Nuclear Information System (INIS)

Jobst, Matthias; Wilhelm, Polina; Kliem, Soeren; Kozmenkov, Yaroslav

2017-01-01

The improvement of the safety of nuclear power plants is a continuously on-going process. The analysis of transients and accidents is an important research topic, which significantly contributes to safety enhancements of existing power plants. In case of an accident with multiple failures of safety systems, core uncovery and heat-up can occur. In order to prevent the accident to turn into a severe one or to mitigate the consequences of severe accidents, different accident management measures can be applied. By means of numerical analyses performed with the compute code ATHLET-CD, the effectiveness of coolant injection with a mobile pump system into the primary circuit of a PWR was studied. According to the analyses, such a system can stop the melt progression if it is activated prior to 10 % of total core is molten.

Genome sequencing elucidates Sardinian genetic architecture and augments association analyses for lipid and blood inflammatory markers

Science.gov (United States)

Zoledziewska, Magdalena; Mulas, Antonella; Pistis, Giorgio; Steri, Maristella; Danjou, Fabrice; Kwong, Alan; Ortega del Vecchyo, Vicente Diego; Chiang, Charleston W. K.; Bragg-Gresham, Jennifer; Pitzalis, Maristella; Nagaraja, Ramaiah; Tarrier, Brendan; Brennan, Christine; Uzzau, Sergio; Fuchsberger, Christian; Atzeni, Rossano; Reinier, Frederic; Berutti, Riccardo; Huang, Jie; Timpson, Nicholas J; Toniolo, Daniela; Gasparini, Paolo; Malerba, Giovanni; Dedoussis, George; Zeggini, Eleftheria; Soranzo, Nicole; Jones, Chris; Lyons, Robert; Angius, Andrea; Kang, Hyun M.; Novembre, John; Sanna, Serena; Schlessinger, David; Cucca, Francesco; Abecasis, Gonçalo R

2015-01-01

We report ~17.6M genetic variants from whole-genome sequencing of 2,120 Sardinians; 22% are absent from prior sequencing-based compilations and enriched for predicted functional consequence. Furthermore, ~76K variants common in our sample (frequency >5%) are rare elsewhere (Genomes Project). We assessed the impact of these variants on circulating lipid levels and five inflammatory biomarkers. Fourteen signals, including two major new loci, were observed for lipid levels, and 19, including two novel loci, for inflammatory markers. New associations would be missed in analyses based on 1000 Genomes data, underlining the advantages of large-scale sequencing in this founder population. PMID:26366554

Zagreb and Tenerife: Airline Accidents Involving Linguistic Factors

Science.gov (United States)

Cookson, Simon

2009-01-01

The International Civil Aviation Organization (ICAO) is currently implementing a program to improve the language proficiency of pilots and air traffic controllers worldwide. In justifying the program, ICAO has cited a number of airline accidents that were at least partly caused by language factors. Two accidents cited by ICAO are analysed in this…

Across the Gap: Geochronological and Sedimentological Analyses from the Late Pleistocene-Holocene Sequence of Goda Buticha, Southeastern Ethiopia

Science.gov (United States)

Asrat, Asfawossen; Bahain, Jean-Jacques; Chapon, Cécile; Douville, Eric; Fragnol, Carole; Hernandez, Marion; Hovers, Erella; Leplongeon, Alice; Martin, Loïc; Pleurdeau, David; Pearson, Osbjorn; Puaud, Simon; Assefa, Zelalem

2017-01-01

Goda Buticha is a cave site near Dire Dawa in southeastern Ethiopia that contains an archaeological sequence sampling the late Pleistocene and Holocene of the region. The sedimentary sequence displays complex cultural, chronological and sedimentological histories that seem incongruent with one another. A first set of radiocarbon ages suggested a long sedimentological gap from the end of Marine Isotopic Stage (MIS) 3 to the mid-Holocene. Macroscopic observations suggest that the main sedimentological change does not coincide with the chronostratigraphic hiatus. The cultural sequence shows technological continuity with a late persistence of artifacts that are usually attributed to the Middle Stone Age into the younger parts of the stratigraphic sequence, yet become increasingly associated with lithic artifacts typically related to the Later Stone Age. While not a unique case, this combination of features is unusual in the Horn of Africa. In order to evaluate the possible implications of these observations, sedimentological analyses combined with optically stimulated luminescence (OSL) were conducted. The OSL data now extend the radiocarbon chronology up to 63 ± 7 ka; they also confirm the existence of the chronological gap between 24.8 ± 2.6 ka and 7.5 ± 0.3 ka. The sedimentological analyses suggest that the origin and mode of deposition were largely similar throughout the whole sequence, although the anthropic and faunal activities increased in the younger levels. Regional climatic records are used to support the sedimentological observations and interpretations. We discuss the implications of the sedimentological and dating analyses for understanding cultural processes in the region. PMID:28125597

Vaporization of structural materials in severe accidents

International Nuclear Information System (INIS)

Lorenz, R.A.

1982-01-01

Vaporized structural materials form the bulk of aerosol particles that can transport fission products in severe LWR accidents. As part of the Severe Accident Sequence Analysis (SASA) program at Oak Ridge National Laboratory, a model has been developed based on a mass transport coefficient to describe the transport of materials from the surface of a molten pool. In many accident scenarios, the coefficient can be calculated from existing correlations for mass transfer by natural convection. Data from SASCHA fuel melting tests (Karlsruhe, Germany) show that the partial pressures of many of the melt components (Fe, Cr, Co, Mn, Sn) required for the model can be calculated from the vapor pressures of the pure species and Raoult's law. These calculations indicate much lower aerosol concentrations than reported in previous studies

Severe accidents and terrorist threats at nuclear reactors

International Nuclear Information System (INIS)

Pollack, G.L.

1987-01-01

Some of the key areas of uncertainty are the nature of the physical and chemical interactions of released fission products and of the interactions between a molten core and concrete, the completeness and validity of the computer codes used to predict accidents, and the behavior of the containment. Because of these and other uncertainties, it is not yet possible to reliably predict the consequences of reactor accidents. It is known that for many accident scenarios, especially less severe ones or where the containment is not seriously compromised, the amount of radioactive material expected to escape the reactor is less, even much less, than was previously calculated. For such accidents, the predictions are easier and more reliable. With severe accidents, however, there is considerable uncertainty as to the predicted results. For accidents of the type that terrorists might cause - for example, where the sequence of failure would be unexpected or where redundant safety features are caused to fail together - the uncertainties are still larger. The conclusion, then, is that there are potential dangers to the public from terrorist actions at a nuclear reactor; however, because of the variety of potential terrorist threats and the incompleteness of the knowledge about the behavior of reactor components and fission products during accidents, the consequences cannot yet be assessed quantitatively

Some Examples of the Relationship Between Containment and Other Engineered Safeguard Requirements, Accident Analyses and Site Conditions

Energy Technology Data Exchange (ETDEWEB)

Vinck, W. F.; Maurer, H. [EURATOM, Brussels (Belgium)

1967-09-15

The paper refers primarily to nuclear power reactors for which EURATOM has performed safety reviews in co-operation with national technical advisory organizations concerned in the licensing procedures. Comparative data are tabulated on a number of containment concepts and other engineered safeguards to protect against or to limit the consequences of major hypothetical accidents for a number of power reactors. Main environmental data, such as magnitudes of exclusion areas and population densities, are also presented. A number of topics of particular interest which were encountered during the safety analysis and which find widespread application in the assessment of the siting conditions and emergency planning are discussed. In this discussion, emphasis is placed on containment, engineered safeguards and emergency equipment. These items are considered in general with emphasis on: (a ) the importance of meeting operability and high efficiency requirements (reliability ) when needed through design and layout; (b) periodic testing and/or inspection possibilities and requirements in order to maintain high availability standards. Attention is drawn to some difficulties which have arisen in connection with design, material choice and construction of steel containment structures and which in the interests of safety as well as of economic optimization justify in the future more care in the use of possibly uniform or single-code requirements. Examples of uncertainties encountered in some accident analyses and their influence on siting considerations are discussed, with emphasis on safeguards intended to retain radioactive material in the plant, such as extent of core damage, iodine plate-out, filtering efficiency, wash-out effects. The means by which some of the main uncertainties have been or can in the future be eliminated through appropriate experimental programmes performed throughout the world are discussed. Some examples are also given of the influence of factors which

Integrated severe accident containment analysis with the CONTAIN computer code

International Nuclear Information System (INIS)

Bergeron, K.D.; Williams, D.C.; Rexroth, P.E.; Tills, J.L.

1985-12-01

Analysis of physical and radiological conditions iunside the containment building during a severe (core-melt) nuclear reactor accident requires quantitative evaluation of numerous highly disparate yet coupled phenomenologies. These include two-phase thermodynamics and thermal-hydraulics, aerosol physics, fission product phenomena, core-concrete interactions, the formation and combustion of flammable gases, and performance of engineered safety features. In the past, this complexity has meant that a complete containment analysis would require application of suites of separate computer codes each of which would treat only a narrower subset of these phenomena, e.g., a thermal-hydraulics code, an aerosol code, a core-concrete interaction code, etc. In this paper, we describe the development and some recent applications of the CONTAIN code, which offers an integrated treatment of the dominant containment phenomena and the interactions among them. We describe the results of a series of containment phenomenology studies, based upon realistic accident sequence analyses in actual plants. These calculations highlight various phenomenological effects that have potentially important implications for source term and/or containment loading issues, and which are difficult or impossible to treat using a less integrated code suite

Evaluation of carbons exposed to the Three Mile Island accident

International Nuclear Information System (INIS)

Deitz, V.R.; Romans, J.B.; Bellamy, R.R.

1981-01-01

One of the lines of defense that served to mitigate the radiological effects of the accident at Three Mile Island was the activated carbon installed in ventilation air flows. Filters in the Auxiliary and Fuel Handling Buildings of Unit 2 adsorbed tens to hundreds of curies of iodine-131, preventing the release to the environment. The carbon exposed to the accident has been replaced and the spent carbon has been analyzed in the laboratory. Independent analyses were performed for the two filter trains in both the Auxiliary and Fuel Handling Buildings, replaced at various times after the accident. The results of these analyses are compared to new (unexposed) carbons

Analysis of Three Mile Island - Unit 2 accident

International Nuclear Information System (INIS)

1979-07-01

The Nuclear Safety Analysis Center (NSAC) of the Electric Power Research Institute is analyzing the Three Mile Island-2 accident. An early result of this analysis was a brief narrative summary, issued in mid May 1979. The present report contains a revised version of that narrative summary, a highly detailed sequence of events, a standard reference list, a list of abbreviations and acronyms, and several appendices. The appendices serve either to describe plant features which are pertinent to the understanding of the sequence of events, or indicate how certain inferences and conclusions in the report were reached. Supplementing the appendices contained herein, additional appendices are in preparation; these will be issued when available (e.g., the appendices Hydrogen Phenomena and Operator Actions during Initial Transient will follow later). Also in preparation is a matrix of equipment and systems actions during the accident. This report together with future supplements and a separate Core Damage Assessment report, will embody the principal results of that phase of NSAC work which is devoted to learning and understanding what happened during the accident. Subsequent phases will concentrate on causes, lessons learned and generic remedial or preventive measures which may be appropriate

Analysis of Three Mile Island-Unit 2 accident

International Nuclear Information System (INIS)

1979-07-01

The Nuclear Safety Analysis Center (NSAC) of the Electic Power Research Institute is analyzing the Three Mile Island-2 accident. An early result of this analysis was a brief narrative summary, issued in mid-May 1979. The present report contains a revised version of that narrative summary, a highly detailed sequence of events, a standard reference list, a list of abbreviations and acronyms, and several appendices. The appendices serve either to describe plant features which are pertinent to the understanding of the sequence of events, or indicate how certain inferences and conclusions in the report were reached. Supplementing the appendices contained herein, additional appendices are in preparation; these will be issued when available (e.g., the appendices Hydrogen Phenomena and Operator Actions duing Initial Transient will follow later). Also in preparation is a matrix of equipment and systems actions during the accident. This report together with future supplements and a separate Core Damage Assessment report, will embody the principal results of that phase of NSAC's work which is devoted to learning and understanding what happened during the accident. Subsequent phases will concentrate on causes, lessons learned and generic remedial or preventive measures which may be appropriate

Incorporation of advanced accident analysis methodology into safety analysis reports

International Nuclear Information System (INIS)

2003-05-01

The IAEA Safety Guide on Safety Assessment and Verification defines that the aim of the safety analysis should be by means of appropriate analytical tools to establish and confirm the design basis for the items important to safety, and to ensure that the overall plant design is capable of meeting the prescribed and acceptable limits for radiation doses and releases for each plant condition category. Practical guidance on how to perform accident analyses of nuclear power plants (NPPs) is provided by the IAEA Safety Report on Accident Analysis for Nuclear Power Plants. The safety analyses are performed both in the form of deterministic and probabilistic analyses for NPPs. It is customary to refer to deterministic safety analyses as accident analyses. This report discusses the aspects of using the advanced accident analysis methods to carry out accident analyses in order to introduce them into the Safety Analysis Reports (SARs). In relation to the SAR, purposes of deterministic safety analysis can be further specified as (1) to demonstrate compliance with specific regulatory acceptance criteria; (2) to complement other analyses and evaluations in defining a complete set of design and operating requirements; (3) to identify and quantify limiting safety system set points and limiting conditions for operation to be used in the NPP limits and conditions; (4) to justify appropriateness of the technical solutions employed in the fulfillment of predetermined safety requirements. The essential parts of accident analyses are performed by applying sophisticated computer code packages, which have been specifically developed for this purpose. These code packages include mainly thermal-hydraulic system codes and reactor dynamics codes meant for the transient and accident analyses. There are also specific codes such as those for the containment thermal-hydraulics, for the radiological consequences and for severe accident analyses. In some cases, codes of a more general nature such

Accident management for PWRs in France and Germany

International Nuclear Information System (INIS)

Heili, F.; Lecomte, C.; L'Homme, A.

1991-11-01

The results of risk analyses, research and particularly the two severe accidents in the nuclear power plants TMI-2 and Chernobyl let to a worldwide re-examination of all aspects dealing with the capability to cope with severe accidents. Strategies have been developed or are under development providing actions that can be taken to prevent severe accidents or to mitigate their consequences. Those strategies are investigated and discussed using the term 'accident management'. The purpose of this report is to present the respective views in France and Germany and to point out differences and commonalties of the approaches. This report also includes proposals for further work

Safety evaluation of accident-tolerant FCM fueled core with SiC-coated zircalloy cladding for design-basis-accidents and beyond DBAs

Energy Technology Data Exchange (ETDEWEB)

Chun, Ji-Han, E-mail: chunjh@kaeri.re.kr; Lim, Sung-Won; Chung, Bub-Dong; Lee, Won-Jae

2015-08-15

Highlights: • Thermal conductivity model of the FCM fuel was developed and adopted in the MARS. • Scoping analysis for candidate FCM FAs was performed to select feasible FA. • Preliminary safety criteria for FCM fuel and SiC/Zr cladding were set up. • Enhanced safety margin and accident tolerance for FCM-SiC/Zr core were demonstrated. - Abstract: The FCM fueled cores proposed as an accident tolerant concept is assessed against the design-basis-accident (DBA) and the beyond-DBA (BDBA) scenarios using MARS code. A thermal conductivity model of FCM fuel is incorporated in the MARS code to take into account the effects of irradiation and temperature that was recently measured by ORNL. Preliminary analyses regarding the initial stored energy and accident tolerant performance were carried out for the scoping of various cladding material candidates. A 16 × 16 FA with SiC-coated Zircalloy cladding was selected as the feasible conceptual design through a preliminary scoping analysis. For a selected design, safety analyses for DBA and BDBA scenarios were performed to demonstrate the accident tolerance of the FCM fueled core. A loss of flow accident (LOFA) scenario was selected for a departure-from-nucleate-boiling (DNB) evaluation, and large-break loss of coolant accident (LBLOCA) scenario for peak cladding temperature (PCT) margin evaluation. A control element assembly (CEA) ejection accident scenario was selected for peak fuel enthalpy and temperature. Moreover, a station blackout (SBO) and LBLOCA without a safety injection (SI) scenario were selected as a BDBA. It was demonstrated that the DBA safety margin of the FCM core is satisfied and the time for operator actions for BDBA s is evaluated.

Complementary safety assessment in the light of the Fukushima accident - Laue Langevin Institute

International Nuclear Information System (INIS)

Desbriere; Caillot; Bidet

2012-01-01

This CSA (Complementary Safety Assessment) analyses the robustness of the Grenoble High Flux reactor to extreme situations such as those that led to the Fukushima accident and proposes a series of improvements. Robustness is the ability for the facility to withstand events beyond the level for which the facility was designed. Robustness is linked to safety margins but also to the situations leading to a sudden deterioration of the accident sequence (cliff edge effect). Safety is not only a matter of design or of engineered systems, it is also a matter of organization. So issues like crisis organization and work organization via subcontracting are also taken into consideration. This report is divided into 9 main chapters: 1) main features of the high flux reactor, 2) macroscopic study of safety, identification of structures and equipment essential to safety, 3) earthquake risk, 4) flood risk, 5) risks due to other extreme natural disasters, 6) the loss of electrical power supplies and of cooling systems, 7) management of severe accidents, 8) subcontracting policy, 9) synthesis and improvements. This study confirms the robustness of the facility and a series of improvements and modifications is proposed to face very unlikely situations (especially plurality of failures) that were not taken into account in baseline safety studies. (A.C.)

Passive depressurization accident management strategy for boiling water reactors

International Nuclear Information System (INIS)

Liu, Maolong; Erkan, Nejdet; Ishiwatari, Yuki; Okamoto, Koji

2015-01-01

Highlights: • We proposed two passive depressurization systems for BWR severe accident management. • Sensitivity analysis of the passive depressurization systems with different leakage area. • Passive depressurization strategies can prevent direct containment heating. - Abstract: According to the current severe accident management guidance, operators are required to depressurize the reactor coolant system to prevent or mitigate the effects of direct containment heating using the safety/relief valves. During the course of a severe accident, the pressure boundary might fail prematurely, resulting in a rapid depressurization of the reactor cooling system before the startup of SRV operation. In this study, we demonstrated that a passive depressurization system could be used as a severe accident management tool under the severe accident conditions to depressurize the reactor coolant system and to prevent an additional devastating sequence of events and direct containment heating. The sensitivity analysis performed with SAMPSON code also demonstrated that the passive depressurization system with an optimized leakage area and failure condition is more efficient in managing a severe accident

Passive depressurization accident management strategy for boiling water reactors

Energy Technology Data Exchange (ETDEWEB)

Liu, Maolong, E-mail: liuml@vis.t.u-tokyo.ac.jp [Department of Nuclear Engineering and Management, School of Engineering, The University of Tokyo (Japan); Erkan, Nejdet [Nuclear Professional School, School of Engineering, The University of Tokyo (Japan); Ishiwatari, Yuki [Department of Nuclear Engineering and Management, School of Engineering, The University of Tokyo (Japan); Hitachi-GE Nuclear Energy, Ltd. (Japan); Okamoto, Koji [Nuclear Professional School, School of Engineering, The University of Tokyo (Japan)

2015-04-01

Highlights: • We proposed two passive depressurization systems for BWR severe accident management. • Sensitivity analysis of the passive depressurization systems with different leakage area. • Passive depressurization strategies can prevent direct containment heating. - Abstract: According to the current severe accident management guidance, operators are required to depressurize the reactor coolant system to prevent or mitigate the effects of direct containment heating using the safety/relief valves. During the course of a severe accident, the pressure boundary might fail prematurely, resulting in a rapid depressurization of the reactor cooling system before the startup of SRV operation. In this study, we demonstrated that a passive depressurization system could be used as a severe accident management tool under the severe accident conditions to depressurize the reactor coolant system and to prevent an additional devastating sequence of events and direct containment heating. The sensitivity analysis performed with SAMPSON code also demonstrated that the passive depressurization system with an optimized leakage area and failure condition is more efficient in managing a severe accident.

Radioactivity control after Fukushima accident

International Nuclear Information System (INIS)

Vukovic, D.; Mitrovic, R.; Vicentijevic, M.; Pantelic, G.

2011-01-01

Fukushima nuclear accident has influence on more attention when radioactivity of fish were controlled. Sea fish, freshwater fish, fish products and fish flour were analysed ( 95 samples). All products were safe for use with radiation-hygienic aspects. [sr

Instrumentation availability during severe accidents for a boiling water reactor with a Mark I containment

International Nuclear Information System (INIS)

Arcieri, W.C.; Hanson, D.J.

1992-02-01

In support of the US Nuclear Regulatory Commission Accident Management Research Program, the availability of instruments to supply accident management information during a broad range of severe accidents is evaluated for a Boiling Water Reactor with a Mark I containment. Results from this evaluation include: (1) the identification of plant conditions that would impact instrument performance and information needs during severe accidents; (2) the definition of envelopes of parameters that would be important in assessing the performance of plant instrumentation for a broad range of severe accident sequences; and (3) assessment of the availability of plant instrumentation during severe accidents

Joint research project WASA-BOSS: Further development and application of severe accident codes. Assessment and optimization of accident management measures. Project B: Accident analyses for pressurized water reactors with the application of the ATHLET-CD code

International Nuclear Information System (INIS)

Jobst, Matthias; Kliem, Soeren; Kozmenkov, Yaroslav; Wilhelm, Polina

2017-02-01

Within the framework of the project an ATHLET-CD input deck for a generic German PWR of type KONVOI has been created. This input deck was applied to the simulation of severe accidents from the accident categories station blackout (SBO) and small-break loss-of-coolant accidents (SBLOCA). The complete accident transient from initial event at full power until the damage of reactor pressure vessel (RPV) is covered and all relevant severe accident phenomena are modelled: start of core heat up, fission product release, melting of fuel and absorber material, oxidation and release of hydrogen, relocation of molten material inside the core, relocation to the lower plenum, damage and failure of the RPV. The model has been applied to the analysis of preventive and mitigative accident management measures for SBO and SBLOCA transients. Therefore, the measures primary side depressurization (PSD), injection to the primary circuit by mobile pumps and for SBLOCA the delayed injection by the cold leg hydro-accumulators have been investigated and the assumptions and start criteria of these measures have been varied. The time evolutions of the transients and time margins for the initiation of additional measures have been assessed. An uncertainty and sensitivity study has been performed for the early phase of one SBO scenario with PSD (until the start of core melt). In addition to that, a code -to-code comparison between ATHLET-CD and the severe accident code MELCOR has been carried out.

A step forward towards understanding the severe accident evolution in Fukushima: Parametric analyses of Unit-I with MELCOR 2.I

International Nuclear Information System (INIS)

Herranz, L. E.; Garcia Martin, M.; Lopez del Pra, C.

2013-01-01

The Fukushima accident on March 11 2011, largely affected nuclear community all over the world. Immediately, many R and D organizations and companies drew their attention to the facts that were being released by Japanese authorities, so that the most through understanding of the situation could be gained at the moment. This paper synthesizes the major progress achieved by CIEMAT in this international environment. The specific target pursued is the comprehension of the severe accident evolution, particularly the progression followed in the unit 1 of Fukushima Daiichi. To do so, the MELCOR 2.1 code has been used to model 6 Fukushima-like SBO sequences in a BWR-Mark I reactor. Particular emphasis has been given to understand the potential impact of systems like the isolation condenser (IC) and the over-pressure protection system. As expected, availability of AC power from a diesel would have drastically changed the scenario, particularly in the containment, due to actuation of DW (Dry-Well) sprays. IC actuation might have delayed the reactor pressure vessel (RPV) failure for hours, if they had performed according to their design. Contrarily, a stuck-open safety relief valve would have resulted in an earlier PRV failure. A definitive picture of the scenario is still far away; however, these results may be seen as a step forward. (Author)

A step forward towards understanding the severe accident evolution in Fukushima: Parametric analyses of Unit-I with MELCOR 2.I

Energy Technology Data Exchange (ETDEWEB)

Herranz, L. E.; Garcia Martin, M.; Lopez del Pra, C.

2013-03-01

The Fukushima accident on March 11 2011, largely affected nuclear community all over the world. Immediately, many R and D organizations and companies drew their attention to the facts that were being released by Japanese authorities, so that the most through understanding of the situation could be gained at the moment. This paper synthesizes the major progress achieved by CIEMAT in this international environment. The specific target pursued is the comprehension of the severe accident evolution, particularly the progression followed in the unit 1 of Fukushima Daiichi. To do so, the MELCOR 2.1 code has been used to model 6 Fukushima-like SBO sequences in a BWR-Mark I reactor. Particular emphasis has been given to understand the potential impact of systems like the isolation condenser (IC) and the over-pressure protection system. As expected, availability of AC power from a diesel would have drastically changed the scenario, particularly in the containment, due to actuation of DW (Dry-Well) sprays. IC actuation might have delayed the reactor pressure vessel (RPV) failure for hours, if they had performed according to their design. Contrarily, a stuck-open safety relief valve would have resulted in an earlier PRV failure. A definitive picture of the scenario is still far away; however, these results may be seen as a step forward. (Author)

Perspectives on the economic risks of LWR accidents

International Nuclear Information System (INIS)

Ritchie, L.T.; Burke, R.P.

1986-01-01

Models which can be used for the analysis of the economic risks from events which may occur during LWR operation have been developed. The models include capabilities to estimate both onsite and offsite costs of LWR events ranging from routine plant forced outages to severe core-melt accidents resulting in large releases of radioactive material to the environment. The economic consequence models have been applied in studies of the economic risks from the operation of US LWR plants. The results of the analyses provide some important perspectives regarding the economic risks of LWR accidents. The analyses indicate that economic risks, in contrast to public health risks, are dominated by the onsite costs of relatively high-frequency forced outage events. Even for severe (e.g., core-melt) accidents, expected offsite costs are less than expected onsite costs for a typical US plant

Status and functioning of the European Commission's major accident reporting system

International Nuclear Information System (INIS)

Kirchsteiger, C.

1999-01-01

This paper describes the background, functioning and status of the European Commission's Major Accident Reporting System (MARS), dedicated to collect, in a consistent way, data on major industrial accidents involving dangerous substances from the Member States of the European Union, to analyse and statistically process them, and to create subsets of all non-confidential accidents data and analysis results for export to all Member States. This modern information exchange and analysis tool is made up of two connected parts: one for each local unit (i.e., for the Competent Authority of each EU Member State), and one central part for the European Commission. The local, as well as the central parts of this information network, can serve both as data logging systems and, on different levels of complexity, as data analysis tools. The central database allows complex cluster and pattern analysis, identifying and analysing the succession of the disruptive factors leading to an accident. On this basis, 'lessons learned' can be formulated for the industry for the purposes of further accident prevention. Further, results from analysing data of major industrial accidents reported to MARS are presented. It can be shown that some of the main assumptions in the new 'Seveso II Directive' can directly be validated from MARS data. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

Analysis and first evaluation of the course of the Chernobyl accident up to the excursion. Interim report. Analyse und erste Bewertung des Unfallablaufs in Tschernobyl bis zur Leistungsexkursion. Zwischenbericht

Energy Technology Data Exchange (ETDEWEB)

Clemente, M; Frisch, W; Langenbuch, S; Weber, J P

1986-01-01

This report contains a description and an evaluation of the course of the Tschernobyl accident up to the excursion. It is based on information obtained during the IAEA conference in Vienna in August 1986 and includes a first qualitative evaluation of the course of the accident as well as results of analyses carried out at GRS. This work was done with the aim to better understand the particular phases of the accident and to demonstrate the typical dynamic behaviour of the RBMK-1000 type reactor with a positive void coefficient in contrast to the behaviour of german BWRs with negativ void coefficients. The calculations also contribute to the evaluation of the consequences of the violations and errors executed by the operating team and the consequences of design weaknesses of the plant.