Workshop on accelerator magnet superconductors. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The workshop on accelerator magnet superconductors has gathered 102 registered participants from research laboratories, universities and industry. 8 European companies, active in superconducting materials and cables were present. This workshop has been organized to deal with the status of the world research and development on superconducting materials and cables for high field magnets (B > 10 T). The workshop has also reviewed the status of high temperature superconductors and transmission line cables for potential use in low field superconducting magnets for injectors and beam transfer lines, as well as cables for pulsed magnets that might be used in future hadron colliders or injectors.

Workshop Engages PCs in Accelerator Controls

International Nuclear Information System (INIS)

Matthew Bickley

2006-01-01

To discuss the rapidly growing and changing use of personal computers (PCs) in accelerator control systems, 80 accelerator controls specialists from 26 institutions in North America, Europe and Asia attended the 6. International Workshop on Personal Computers and Particle Accelerator Controls, PCaPAC2006, held October 24-27 at Jefferson Lab in Newport News, Virginia. PCs have become increasingly applicable to the control of accelerators as their computing capacities have increased exponentially over the last 10 years. Capabilities that once required the power available only from expensive, small-market systems offered by DEC, Sun or IBM can now be obtained with commodity hardware offered by many vendors. The price/performance ratio presented by any standard PC makes a compelling case for using PC hardware in accelerator controls wherever possible. The PCaPAC meeting underscored the importance of collaborative control system development. Several talks focused on additions to three such systems, TINE, TANGO and EPICS. The diverse contributions to these toolkits, both in content and source, demonstrate the power of leveraged software development across a number of facilities. TINE originated in DESY's desire to give users a unified software bus above disparate underlying platforms. TINE discussions at PCaPAC centered on the toolkit's interface layers, including address redirection and integration with other control systems. TANGO has been a collaborative effort from its inception. Based on CORBA, this open-source controls toolkit is a registered project in the source forge system. The workshop TANGO presentation discussed contributions from four TANGO institutions, and mentioned a broad range of new tools, from user interface applications to code generators and database integration software. EPICS, which was started at LANL in the 1980s, includes contributions from dozens of institutions around the world. EPICS-related PCaPAC discussions included virtual machines at

Accelerating the Development of 21st-Century Toxicology: Outcome of a Human Toxicology Project Consortium Workshop

Science.gov (United States)

Stephens, Martin L.; Barrow, Craig; Andersen, Melvin E.; Boekelheide, Kim; Carmichael, Paul L.; Holsapple, Michael P.; Lafranconi, Mark

2012-01-01

The U.S. National Research Council (NRC) report on “Toxicity Testing in the 21st century” calls for a fundamental shift in the way that chemicals are tested for human health effects and evaluated in risk assessments. The new approach would move toward in vitro methods, typically using human cells in a high-throughput context. The in vitro methods would be designed to detect significant perturbations to “toxicity pathways,” i.e., key biological pathways that, when sufficiently perturbed, lead to adverse health outcomes. To explore progress on the report’s implementation, the Human Toxicology Project Consortium hosted a workshop on 9–10 November 2010 in Washington, DC. The Consortium is a coalition of several corporations, a research institute, and a non-governmental organization dedicated to accelerating the implementation of 21st-century Toxicology as aligned with the NRC vision. The goal of the workshop was to identify practical and scientific ways to accelerate implementation of the NRC vision. The workshop format consisted of plenary presentations, breakout group discussions, and concluding commentaries. The program faculty was drawn from industry, academia, government, and public interest organizations. Most presentations summarized ongoing efforts to modernize toxicology testing and approaches, each with some overlap with the NRC vision. In light of these efforts, the workshop identified recommendations for accelerating implementation of the NRC vision, including greater strategic coordination and planning across projects (facilitated by a steering group), the development of projects that test the proof of concept for implementation of the NRC vision, and greater outreach and communication across stakeholder communities. PMID:21948868

Report of the Los Alamos accelerator automation application toolkit workshop

International Nuclear Information System (INIS)

Clout, P.; Daneels, A.

1990-01-01

A 5 day workshop was held in November 1988 at Los Alamos National Laboratory to address the viability of providing a toolkit optimized for building accelerator control systems. The workshop arose from work started independently at Los Alamos and CERN. This paper presents the discussion and the results of the meeting. (orig.)

Workshop of the JAEA-Tokai Tandem Accelerator. Memorial of 100,000-hour operation

International Nuclear Information System (INIS)

Ishii, Tetsuro; Osa, Akihiko

2009-04-01

Workshop of the JAEA-Tokai tandem accelerator has been held every two years. As a memorial of 100,000-hour operation of the tandem accelerator, we have organized the workshop focusing on the activity at this facility. This workshop covers developments and experiments carried out so far, together with experiments in progress and proposals in future. As previous series of workshops, we offered an opportunity to have active discussion among scientists in different fields including accelerator, nuclear physics, nuclear chemistry, radiation effects, atomic physics and so on, aiming at extending facility and research interactively. As a memorial lecture, we invited Dr. Akira Tonomura of fellow of Hitachi, Ltd, a distinctive scientist for development of electron holography. He delivered a lecture titled 'Structure of magnetic flux observed by electron beam'. He once used the tandem accelerator to induce columnar defects in high-temperature superconductor and studied vortices trapped along the defects. Prof. Shigeru Kubono of University of Tokyo, a chairman of program advisory committee of the tandem accelerator, encouraged us through a talk of 'Expectations for the JAEA-Tokai tandem accelerator'. This workshop was held at Advanced Science Research Center Building in Nuclear Science Research Institute on January 6th and 7th in 2009, having 24 oral presentations and 48 posters, and successfully carried out with as many as 120 participants and a lot of science discussions. This review is the collection of slides of oral presentations. The colored slides can be also found in the home page of the tandem accelerator facility (http://rrsys.tokai-sc.jaea.go.jp/rrsys/html/tandem/index.html). (author)

Workshop on Accelerator Magnet Superconductors, Design and Optimization

CERN Document Server

WAMSDO Workshop

2009-01-01

This report contains the proceedings of the CARE-HHH-AMT Workshop on Accelerator Magnet Superconductors, Design and Optimization (WAMSDO) held at CERN from 19 to 23 May 2008. The needs in terms of superconducting magnets for the accelerator projects were discussed, mainly for the LHC interaction regions and injector upgrades, and for the GSI FAIR complex. The first part of the workshop focused on the development of superconductor and cables, i.e., low-loss Nb-Ti cables, Nb$_{3}$Sn and high-temperature superconductors. An industry session summarized the actual plans and status of the activities in the main European industries. Then, a worldwide status of the high field magnets programme was presented. A special session was devoted to fast cycled magnets, including FAIR facilities and LHC injector upgrades. A final session focused on the optimization methods and numerical tools for magnet design.

Theoretical Investigations of Plasma-Based Accelerators and Other Advanced Accelerator Concepts

International Nuclear Information System (INIS)

Shuets, G.

2004-01-01

Theoretical investigations of plasma-based accelerators and other advanced accelerator concepts. The focus of the work was on the development of plasma based and structure based accelerating concepts, including laser-plasma, plasma channel, and microwave driven plasma accelerators

Proceedings of a workshop on Applications of Accelerators

International Nuclear Information System (INIS)

Herrmannsfeldt, W.B.; Sessler, A.M.; Alonso, J.R.

1994-01-01

This document is a compilation of material collected as the results of a workshop, Applications of Accelerators, held at the Stanford Linear Accelerator Center, 1--2 December 1993. The material collected here has been edited for style and to minimize duplication. Footnotes will identify the original source of the material. We believe that the reader will find that this document has something for every interest. There are applications in the fields of health, food preservation, energy, environmental monitoring and protection, and industrial processing. Man y of the examples discussed have already passed the demonstration stage. Most of the others are the subject of active accelerator research. Taken as a whole, the particle accelerator field contains a wealth of application opportunities, some already in use, and many more ready to be exploited

1st oPAC Topical Workshop: Grand Challenges in Accelerator Optimisation

CERN Document Server

2013-01-01

Accelerators are key instruments for fundamental research, health and industry applications. International collaboration is very important for their continued optimisation. To address this oPAC is organising this two-day international workshop on Grand Challenges in Accelerator Optimisation. The workshop will provide an overview of the current state of the art in beam physics, numerical simulations and beam instrumentation and highlight existing limitations. It will discuss research and development being undertaken and ambitions to further improve the performance of existing and future facilities. In addition to invited talks, there will be industry displays and a special seminar covering recent LHC discoveries. All participants will have an opportunity to contribute a poster.

Proceedings of the FNCA workshop on application of electron accelerator

International Nuclear Information System (INIS)

Yoshii, Fumio; Kume, Tamikazu

2003-02-01

'Forum for Nuclear Cooperation in Asia (FNCA) Workshop on Application of Electron Accelerator' was sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT) and hosted by Japan Atomic Energy Research Institute (JAERI) and Japan Atomic Industry Forum (JAIF). It was held at the Takasaki Radiation Chemistry Research Establishment (TRCRE), JAERI, Takasaki, Japan from 28 January to 1 February, 2002. The Workshop was attended by experts on application of electron accelerator from each of the participating countries, i.e. China, Indonesia, Korea, Malaysia, The Philippines, Thailand and Vietnam and 16 participants from Japan. A total of 17 papers including invited papers on the current status of application of electron accelerator in the participating countries were presented. The characteristics of various kinds of electron accelerators were introduced. Current research and development on the utilization radiation processing for natural rubber latex, natural polymer solution, polymer films, sterilization of spices and seeds, radiation treatment of flue gases and dioxin in liquid, solid, and gases were reported. Based on the proposed needs from the participating countries, the work plan was discussed and agreed on application of electron accelerator for liquid and for solid (thin films and granules/powder). All manuscripts submitted by every speaker were included in the proceedings. The 16 of the presented papers are indexed individually. (J.P.N.)

Proceedings of the FNCA workshop on application of electron accelerator

Energy Technology Data Exchange (ETDEWEB)

Yoshii, Fumio; Kume, Tamikazu (eds.) [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

2003-02-01

'Forum for Nuclear Cooperation in Asia (FNCA) Workshop on Application of Electron Accelerator' was sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT) and hosted by Japan Atomic Energy Research Institute (JAERI) and Japan Atomic Industry Forum (JAIF). It was held at the Takasaki Radiation Chemistry Research Establishment (TRCRE), JAERI, Takasaki, Japan from 28 January to 1 February, 2002. The Workshop was attended by experts on application of electron accelerator from each of the participating countries, i.e. China, Indonesia, Korea, Malaysia, The Philippines, Thailand and Vietnam and 16 participants from Japan. A total of 17 papers including invited papers on the current status of application of electron accelerator in the participating countries were presented. The characteristics of various kinds of electron accelerators were introduced. Current research and development on the utilization radiation processing for natural rubber latex, natural polymer solution, polymer films, sterilization of spices and seeds, radiation treatment of flue gases and dioxin in liquid, solid, and gases were reported. Based on the proposed needs from the participating countries, the work plan was discussed and agreed on application of electron accelerator for liquid and for solid (thin films and granules/powder). All manuscripts submitted by every speaker were included in the proceedings. The 16 of the presented papers are indexed individually. (J.P.N.)

Report of the workshop on accelerator-based atomic and molecular science

International Nuclear Information System (INIS)

Meyerhof, W.E.

1981-01-01

This Workshop, held in New London, NH on July 27-30, 1980, had a registration of 43, representing an estimated one-third of all principal investigators in the United States in this research subfield. The workshop was organized into 5 working groups for the purpose of (1) identifying some vital physics problems which experimental and theoretical atomic and molecular science can address with current and projected techniques; (2) establishing facilities and equipment needs required to realize solutions to these problems; (3) formulating suggestions for a coherent national policy concerning this discipline; (4) assessing and projecting the manpower situation; and (5) evaluating the relations of this interdisciplinary science to other fields. Recommedations deal with equipment and operating costs for small accelerator laboratories, especially at universities; instrumentation of ion beam lines dedicated to atomic and molecular science at some large accelerators; development of low-velocity, high charge-state ion sources; synchrotron light sources; improvement or replacement of tandem van de Graaff accelerators; high-energy beam lines for atomic physics; the needs for postdoctoral support in this subfield; new accelerator development; need for representatives from atomic and molecular science on program committees for large national accelerator facilities; and the contributions the field can make to applied physics problems

Report on the Workshop on Accelerated Nuclear Energy Materials Development

Energy Technology Data Exchange (ETDEWEB)

King, Wayne E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Allen, Todd [Univ. of Wisconsin, Madison, WI (United States); Arsenlis, Tom [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bench, Graham [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bulatov, Vasily [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fluss, Michael [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Klein, Richard [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McMahon, Donn [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Middleton, Carolin [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Morley, Maureen [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Pasamehmetoglu, Kemal [Idaho National Lab. (INL), Idaho Falls, ID (United States); Turchi, Patrice [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Was, Gary [Univ. of Michigan, Ann Arbor, MI (United States)

2010-05-11

This document reports on the Office of Nuclear Energy’s (NE’s) Workshop on Accelerated Nuclear Energy Materials Development held May 11, 2010, in Washington, DC. The purpose of the workshop was twofold: (1) to provide feedback on an initiative to use uncertainty quantification (UQ) to integrate theory, simulation, and modeling with accelerated experimentation to predict the behavior of materials and fuels in an irradiation environment and thereby accelerate the lengthy materials design and qualification process; and (2) to provide feedback on and refinement to five topical areas to develop predictive models for fuels and cladding and new radiation-tolerant materials. The goal of the workshop was to gather technical feedback with respect to the Office of Nuclear Energy’s research and development while also identifying and highlighting crosscutting capability and applicability of the initiative to other federal offices, including the Department of Energy’s (DOE’s) National Nuclear Security Administration (NNSA), Nuclear Regulatory Commission (NRC), DOE Office of Basic Energy Sciences (BES), DOE Office of Fusion Energy Sciences (FES), and Naval Reactors. The goals of the initiative are twofold: (1) develop time- and length-scale transcending models that predict material properties using UQ to effectively integrate theory, simulation, and modeling with accelerated experiments; and (2) design and develop new radiation-tolerant materials using the knowledge gained and methodologies created to shorten the development and qualification time and reduce cost. The initiative is crosscutting and has synergy with industry and other federal offices including Naval Reactors, NRC, FES, BES, and the Office of Advanced Scientific Computing Research (ASCR). It is distinguished by its use of uncertainty quantification to effectively integrate theory, simulation, and modeling with high-dose experimental capabilities. The initiative aims to bring the methodology that is being

Proceedings of the fifth PTCOG meeting and international workshop on biomedical accelerators

Energy Technology Data Exchange (ETDEWEB)

1987-04-01

This volume contains the proceeding and individual papers presented at the Fifth PTCOG meeting and International Workshop on Biomedical Accelerators. The meeting was divided into sessions on the biomedical aspects of therapy delivery, new biomedical accelerators, facilities, and beam localization and status report. Individual papers have been abstracted and indexed for the Energy Data Base.

Proceedings of the fifth PTCOG meeting and international workshop on biomedical accelerators

International Nuclear Information System (INIS)

1987-04-01

This volume contains the proceeding and individual papers presented at the Fifth PTCOG meeting and International Workshop on Biomedical Accelerators. The meeting was divided into sessions on the biomedical aspects of therapy delivery, new biomedical accelerators, facilities, and beam localization and status report. Individual papers have been abstracted and indexed for the Energy Data Base

Second Annual Transformative Vertical Flight Concepts Workshop: Enabling New Flight Concepts Through Novel Propulsion and Energy Architectures

Science.gov (United States)

Dudley, Michael R. (Editor); Duffy, Michael; Hirschberg, Michael; Moore, Mark; German, Brian; Goodrich, Ken; Gunnarson, Tom; Petermaier,Korbinian; Stoll, Alex; Fredericks, Bill;

Technology and Components of Accelerator-driven Systems. Second International Workshop Proceedings, Nantes, France, 21-23 May 2013

International Nuclear Information System (INIS)

2015-01-01

The accelerator-driven system (ADS) is a potential transmutation system option as part of partitioning and transmutation strategies for radioactive waste in advanced nuclear fuel cycles. Following the success of the workshop series on the utilisation and reliability of the High Power Proton Accelerators (HPPA), the scope of this new workshop series on Technology and Components of Accelerator-driven Systems has been extended to cover subcritical systems as well as the use of neutron sources. The workshop organised by the OECD Nuclear Energy Agency provided experts with a forum to present and discuss state-of-the-art developments in the field of ADS and neutron sources. A total of 40 papers were presented during the oral and poster sessions. Four technical sessions were organised addressing ADS experiments and test facilities, accelerators, simulation, safety, data, neutron sources that were opportunity to present the status of projects like the MYRRHA facility, the MEGAPIE target, FREYA and GUINEVERE experiments, the KIPT neutron source, and the FAIR linac. These proceedings include all the papers presented at the workshop

Proceedings of the Advanced Hadron Facility accelerator design workshop

International Nuclear Information System (INIS)

Thiessen, H.A.

1989-01-01

The International Workshop on Hadron Facility Technology was held February 22-27, 1988, at the Study Center at Los Alamos National Laboratory. The program included papers on facility plans, beam dynamics, and accelerator hardware. The parallel sessions were particularly lively with discussions of all facets of kaon factory design. The workshop provided an opportunity for communication among the staff involved in hadron facility planning from all the study groups presently active. The recommendations of the workshop include: the need to use h=1 RF in the compressor ring; the need to minimize foil hits in painting schemes for all rings; the need to consider single Coulomb scattering in injection beam los calculations; the need to study the effect of field inhomogeneity in the magnets on slow extraction for the 2.2 Tesla main ring of AHF; and agreement in principle with the design proposed for a joint Los Alamos/TRIUMF prototype main ring RF cavity

The Pulse Line Ion Accelerator Concept

Energy Technology Data Exchange (ETDEWEB)

Briggs, Richard J.

2006-02-15

The Pulse Line Ion Accelerator concept was motivated by the desire for an inexpensive way to accelerate intense short pulse heavy ion beams to regimes of interest for studies of High Energy Density Physics and Warm Dense Matter. A pulse power driver applied at one end of a helical pulse line creates a traveling wave pulse that accelerates and axially confines the heavy ion beam pulse. Acceleration scenarios with constant parameter helical lines are described which result in output energies of a single stage much larger than the several hundred kilovolt peak voltages on the line, with a goal of 3-5 MeV/meter acceleration gradients. The concept might be described crudely as an ''air core'' induction linac where the PFN is integrated into the beam line so the accelerating voltage pulse can move along with the ions to get voltage multiplication.

REMOTE OPERATIONS IN A GLOBAL ACCELERATOR NETWORK

International Nuclear Information System (INIS)

PEGGS, S.; SATOGATA, T.; AGARWAL, D.; RICE, D.

2003-01-01

The INTRODUCTION to this paper summarizes the history of the Global Accelerator Network (GAN) concept and the recent workshops that discussed the relationship between GAN and Remote Operations. The REMOTE OPERATIONS SCENARIOS section brings out the organizational philosophy embodied in GAN-like and to non-GAN-like scenarios. The set of major TOPICS RAISED AT THE WORKSHOPS are only partially resolved. COLLABORATION TOOLS are described and discussed, followed by examples of REMOTE ACCELERATOR CONTROL PROJECTS around the world

Remote operations in a global accelerator network

International Nuclear Information System (INIS)

Peggs, Steve; Satogata, Todd; Agarwal, Deborah; Rice, David

2003-01-01

The INTRODUCTION to this paper summarizes the history of the Global Accelerator Network (GAN) concept and the recent workshops that discussed the relationship between GAN and Remote Operations. The REMOTE OPERATIONS SCENARIOS section brings out the organizational philosophy embodied in GAN-like and to non-GAN-like scenarios. The set of major TOPICS RAISED AT THE WORKSHOPS are only partially resolved. COLLABORATION TOOLS are described and discussed, followed by examples of REMOTE ACCELERATOR CONTROL PROJECTS around the world

REMOTE OPERATIONS IN A GLOBAL ACCELERATOR NETWORK.

Energy Technology Data Exchange (ETDEWEB)

PEGGS,S.; SATOGATA,T.; AGARWAL,D.; RICE,D.

2003-05-12

The INTRODUCTION to this paper summarizes the history of the Global Accelerator Network (GAN) concept and the recent workshops that discussed the relationship between GAN and Remote Operations. The REMOTE OPERATIONS SCENARIOS section brings out the organizational philosophy embodied in GAN-like and to non-GAN-like scenarios. The set of major TOPICS RAISED AT THE WORKSHOPS are only partially resolved. COLLABORATION TOOLS are described and discussed, followed by examples of REMOTE ACCELERATOR CONTROL PROJECTS around the world.

Summary Report of Working Group 1: Laser-Plasma Acceleration

Energy Technology Data Exchange (ETDEWEB)

Geddes, C.G.R.; Clayton, C.; Lu, W.; Thomas, A.G.R.

2010-06-01

Advances in and physics of the acceleration of particles using underdense plasma structures driven by lasers were the topics of presentations and discussions in Working Group 1 of the 2010 Advanced Accelerator Concepts Workshop. Such accelerators have demonstrated gradients several orders beyond conventional machines, with quasi-monoenergetic beams at MeV-GeV energies, making them attractive candidates for next generation accelerators. Workshop discussions included advances in control over injection and laser propagation to further improve beam quality and stability, detailed diagnostics and physics models of the acceleration process, radiation generation as a source and diagnostic, and technological tools and upcoming facilities to extend the reach of laser-plasma accelerators.

Summary Report of Working Group 1: Laser-Plasma Acceleration

International Nuclear Information System (INIS)

Geddes, C.G.R.; Clayton, C.; Lu, W.; Thomas, A.G.R.

2010-01-01

Advances in and physics of the acceleration of particles using underdense plasma structures driven by lasers were the topics of presentations and discussions in Working Group 1 of the 2010 Advanced Accelerator Concepts Workshop. Such accelerators have demonstrated gradients several orders beyond conventional machines, with quasi-monoenergetic beams at MeV-GeV energies, making them attractive candidates for next generation accelerators. Workshop discussions included advances in control over injection and laser propagation to further improve beam quality and stability, detailed diagnostics and physics models of the acceleration process, radiation generation as a source and diagnostic, and technological tools and upcoming facilities to extend the reach of laser-plasma accelerators.

Working Group summary reports from the Advanced Photon Source reliability workshop

International Nuclear Information System (INIS)

1992-05-01

A workshop was held at APS to address reliability goals for accelerator systems. Seventy-one individuals participated in the workshop, including 30 from other institutions. The goals of the workshop were to: (1) Give attendees an introduction to the basic concepts of reliability analysis. (2) Exchange information on operating experience at existing accelerator facilities and strategies for achieving reliability at facilities under design or in construction. (3) Discuss reliability goals for APS and the means of their achievement. This report contains the working group summary report an APS's following systems: RF Systems; Power Supplies; Magnet Systems; Interlock and Diagnostics; and Vacuum Systems

Summary Report of Working Group: Laser-Plasma Acceleration

International Nuclear Information System (INIS)

Esarey, Eric; Schroeder, Carl B.; Tochitsky, Sergei; Milchberg, Howard M.

2004-01-01

A summary is given on the work presented and discussed in the Laser-Plasma Acceleration Working Group at the 2004 Advanced Accelerator Concepts Workshop, including the Plasma Acceleration Subgroup (Group-Leader: Eric Esarey; Co-Group-Leader: Sergei Tochitsky) and the Plasma Guiding Subgroup (Group-Leader: Howard Milchberg; Co-Group-Leader: Carl Schroeder)

Review of Advanced Accelerator Concepts R & D in Japan

Science.gov (United States)

Kitagawa, Yoneyoshi; Uesaka, Mitsuru; Koyama, Kazuyoshi; Nakajima, Kaszuhisa; Tajima, Toshiki; Daido, Hiroyuki; Ogata, Atsushi; Nemoto, Koshichi; Nishida, Yasushi; Yugami, Noboru; Miyamoto, Shuji; Dobashi, Katsuhiro

2004-12-01

More than 15 Japanese laboratories are dedicated to the advanced and compact accelerator development. Some use ultra-intense lasers and others use microwave concepts. As for the laser electron accleration, the topics are the capillary acceleration and the mono-energetic acceleration. The laser ion acceleration is also active. As well, the compatization is proceeding of the current rf accelerator. The National Institute for Radiological Science is promoting an advanced accelerator concept project mainly for the medical application.

CERN Technical training 2008 - Learning for the LHC: Special Workshop demonstrating reliability with accelerated testing

CERN Multimedia

2008-01-01

Larry Edson’s workshop will show examples of quantitative reliability predictions based upon accelerated testing and demonstrates that reliability testing during the prototyping phase will help ascertain product shortcomings. When these weak points are addressed and the redesigned product is re-tested, the reliability of that product will become much higher. These methodologies successfully used in industry might be exceedingly useful also for component development in particle physics where reliability is of utmost importance. This training will provide participants with the skills necessary to demonstrate reliability requirements using accelerated testing methods. The workshop will focus on accelerated test design that employs increased stress levels. This approach has the advantage of reducing test time, sample size and test facility resources. The methodologies taught are applicable to all types of stresses, spanning the electro...

CERN Technical training 2008 - Learning for the LHC: Special Workshop demonstrating reliability with accelerated testing

CERN Multimedia

2008-01-01

Larry Edson’s workshop will show examples of quantitative reliability predictions based upon accelerated testing and demonstrate that reliability testing during the prototyping phase will help ascertain product shortcomings. When these weak points are addressed and the redesigned product is re-tested, the reliability of that product will become much higher. These methodologies successfully used in industry might be exceedingly useful also for component development in particle physics where reliability is of the utmost importance. This training will provide participants with the skills necessary to demonstrate reliability requirements using accelerated testing methods. The workshop will focus on accelerated test design that employs increased stress levels. This approach has the advantage of reducing test time, sample size and test facility resources. The methodologies taught are applicable to all types of stresses, spanning the elec...

CERN Technical training 2008 - Learning for the LHC: Special workshop demonstrating reliability with accelerated testing

CERN Multimedia

2008-01-01

Larry Edson’s workshop will show examples of quantitative reliability predictions based upon accelerated testing and demonstrate that reliability testing during the prototyping phase will help ascertain product shortcomings. When these weak points are addressed and the redesigned product is re-tested, the reliability of that product will become much higher. These methodologies successfully used in industry might be exceedingly useful also for component development in particle physics where reliability is of the utmost importance. This training will provide participants with the skills necessary to demonstrate reliability requirements using accelerated testing methods. The workshop will focus on accelerated test design that employs increased stress levels. This approach has the advantage of reducing test time, sample size and test facility resources. The methodologies taught are applicable to all types of stresses, spanning the elec...

Proceedings of the FNCA 2005 workshop on application of electron accelerator. EB treatment of wastewater

International Nuclear Information System (INIS)

Yoshii, Fumio; Kume, Tamikazu

2006-08-01

'Forum for Nuclear Cooperation in Asia (FNCA) Workshop on Application of Electron Accelerator' was sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT), Japan. The 2005 workshop was jointly organized by the Ministry of Science and Technology (MOST), Korea, Korea Atomic Energy Research Institute and Japan Atomic Energy Agency (JAEA). It was held at the International Nuclear Technology and Education Center (INTEC/KAERI), Daejeon, Korea from 14 to 18 November 2005. The Workshop was attended by 32 experts on application of electron accelerator from each of the participating countries, i.e., China (1), Indonesia (1), Korea (18), Malaysia (2), Philippines (1), Thailand (1) and Vietnam (1), and 7 participants from Japan. On the first day, a National Executive Management Seminar on Application of Electron Accelerator was held and attended by 45 participants. Total of 20 papers including Seminar lectures, invited papers on wastewater treatment by electron beam, and country reports on EB irradiation system were presented. The major areas of interest of FNCA member states for cooperation were identified for application of low energy electron accelerator to liquids (natural polymer, wastewater), solids (hydrogel, thin film) and gases (flue gas). Based on the evaluation and proposal from the participating countries, discussions were carried out to re-formulate the work plan of the project on natural polymers and wastewater for three years until FY 2008. It was agreed the FNCA 2006 workshop on EB crosslinking of natural polymers would be held in Malaysia. All manuscripts submitted by every speaker were included in the proceedings. The 18 presented papers are indexed individually. (J.P.N.)

Shielding Aspects of Accelerators, Targets and Irradiation Facilities - SATIF-11 Workshop Proceedings Report

International Nuclear Information System (INIS)

2013-01-01

Particle accelerators have evolved over the last decades from simple devices to powerful machines. In recent years, new technological and research applications have helped to define requirements while the number of accelerator facilities in operation, being commissioned, designed or planned has grown significantly. Their parameters, which include the beam energy, currents and intensities, and target composition, can vary widely, giving rise to new radiation shielding issues and challenges. Particle accelerators must be operated in safe ways to protect operators, the public and the environment. As the design and use of these facilities evolve, so must the analytical methods used in the safety analyses. These workshop proceedings review the state of the art in radiation shielding of accelerator facilities and irradiation targets. They also evaluate progress in the development of modelling methods used to assess the effectiveness of such shielding as part of safety analyses. The transport of radiation through shielding materials is a major consideration in the safety design studies of nuclear power plants, and the modelling techniques used may be applied to many other types of scientific and technological facilities. Accelerator and irradiation facilities represent a key capability in R and D, medical and industrial infrastructures, and they can be used in a wide range of scientific, medical and industrial applications. High-energy ion accelerators, for example, are now used not only in fundamental research, such as the search for new super-heavy nuclei, but also for therapy as part of cancer treatment. While the energy of the incident particles on the shielding of these facilities may be much higher than those found in nuclear power plants, much of the physics associated with the behaviour of the secondary particles produced is similar, as are the computer modelling techniques used to quantify key safety design parameters, such as radiation dose and activation levels

Proceedings of the FNCA 2004 workshop on application of electron accelerator. EB treatment of flue gases

International Nuclear Information System (INIS)

Yoshii, Fumio; Kume, Tamikazu

2005-06-01

'Forum for Nuclear Cooperation in Asia (FNCA) Workshop on Application of Electron Accelerator' was sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT). The 2004 workshop was jointly organized by China Atomic Energy Authority (CAEA), Institute of Modern Physics/Chinese Academy of Sciences(IMP-CAS) and Japan Atomic Energy Research Institute (JAERI). It was held at Prime Hotel, Beijing, China from 6 to 10 September 2004. The Workshop was attended by 28 experts on application of electron accelerator from each of the participating countries, i.e., China, Indonesia, Korea, Malaysia, The Philippines, Thailand and Vietnam, and 10 participants from Japan. On the first day, a National Executive Management Seminar on Application of Electron Accelerator was held and attended by 67 participants. Total of 20 papers including Seminar lectures, invited papers on flue gas treatment by electron beam, and country reports on EB irradiation system were presented. The major areas of interest of FNCA member states for cooperation were identified for application of low energy electron accelerator as liquid (natural polymer, wastewater), solid (hydrogel, thin film) and gases (flue gas). Based on the proposal from the participating countries, discussions were carried out to re-formulate the work plan of the project for three years until FY 2005. It was agreed the FNCA 2005 workshop on EB treatment of wastewater will be held in Korea. All manuscripts submitted by every speaker were included in the proceedings. The 20 of the presented papers are indexed individually. (J.P.N.)

Proceedings of the third ICFA mini-workshop on high intensity, high brightness hadron accelerators

International Nuclear Information System (INIS)

Roser, T.

1997-01-01

The third mini-workshop on high intensity, high brightness hadron accelerators was held at Brookhaven National Laboratory on May 7-9, 1997 and had about 30 participants. The workshop focussed on rf and longitudinal dynamics issues relevant to intense and/or bright hadron synchrotrons. A plenary session was followed by four sessions on particular topics. This document contains copies of the viewgraphs used as well as summaries written by the session chairs

A LEGO paradigm for virtual accelerator concept

International Nuclear Information System (INIS)

Andrianov, S.; Ivanov, A.; Podzyvalov, E.

2012-01-01

The paper considers basic features of a Virtual Accelerator concept based on LEGO paradigm. This concept involves three types of components: different mathematical models for accelerator design problems, integrated beam simulation packages (i. e. COSY, MAD, OptiM and others), and a special class of virtual feedback instruments similar to real control systems (EPICS). All of these components should inter-operate for more complete analysis of control systems and increased fault tolerance. The Virtual Accelerator is an information and computing environment which provides a framework for analysis based on these components that can be combined in different ways. Corresponding distributed computing services establish interaction between mathematical models and low level control system. The general idea of the software implementation is based on the Service-Oriented Architecture (SOA) that allows using cloud computing technology and enables remote access to the information and computing resources. The Virtual Accelerator allows a designer to combine powerful instruments for modeling beam dynamics in a friendly way including both self-developed and well-known packages. In the scope of this concept the following is also proposed: the control system identification, analysis and result verification, visualization as well as virtual feedback for beam line operation. The architecture of the Virtual Accelerator system itself and results of beam dynamics studies are presented. (authors)

Presentations from the Second ORION Workshop, Stanford Linear Accelerator Center, February 18-20, 2003

International Nuclear Information System (INIS)

Noble, Robert

2003-01-01

ORION will be a dedicated user facility available for experimental research in plasma and laser acceleration of particles, beam-plasma physics, ultra-short pulse electron and radiation sources, and potentially laboratory astrophysics. It will bring together a diverse collection of researchers motivated to solve some of the most complex and fascinating problems in these fields. The ORION Facility will be based on the Next Linear Collider Test Accelerator (NLCTA), an existing accelerator at SLAC capable of producing 60 to 350 MeV electron beams. The NLCTA will be augmented with a new photo-injector source, two experimental halls, extraction beamlines, a user laser room, and a data acquisition area. Facility construction is anticipated to start in October 2003, and first beam for experiments is planned for 2005. A central goal of ORION is to provide a facility responsive to the research needs of its users. The workshop's purpose is to explore the range of experiments envisioned by potential users and review the types of beams available and the desired beam parameters. This workshop is an opportunity for the research community to provide input on the facility's test beams, layout, shared diagnostic equipment, simulation and computing capabilities, and user support infrastructure. Results from the workshop will go into determining the facility's design as well as help the SLAC management plan for future user needs on the site once operations begin

Current concepts in lung dosimetry. Proceedings of a special workshop

International Nuclear Information System (INIS)

Fisher, D.R.

1983-02-01

The proceedings of the first special workshop on Lung Dosimetry include the presentation of many new concepts and the reassessment of traditional ideas in lung dosimetry and risk evaluation. Separate abstracts were prepared for the 21 papers in the proceedings

Proceedings of the workshop on prospects for research with radioactive beams from heavy ion accelerators

International Nuclear Information System (INIS)

Nitschke, J.M.

1984-04-01

The SuperHILAC Users Executive Committee organized a workshop on Prospects for Research with Radioactive Beams from Heavy Ion Accelerators. The main purpose of the workshop was to bring together a diverse group of scientists who had already done experients with radioactive beams or were interested in their use in the future. The topics of the talks ranged from general nuclear physics, astrophysics, production of radioactive beams and high energy projectile fragmentation to biomedical applications. This publication contains the abstracts of the talks given at the workshop and copies of the viewgraphs as they were supplied to the editor

Technology and applications of advanced accelerator concepts

CERN Document Server

Chou, Weiren

2016-01-01

Since its invention in the 1920s, particle accelerators have made tremendous progress in accelerator science, technology and applications. However, the fundamental acceleration principle, namely, to apply an external radiofrequency (RF) electric field to accelerate charged particles, remains unchanged. As this method (either room temperature RF or superconducting RF) is approaching its intrinsic limitation in acceleration gradient (measured in MeV/m), it becomes apparent that new methods with much higher acceleration gradient (measured in GeV/m) must be found for future very high energy accelerators as well as future compact (table-top or room-size) accelerators. This volume introduces a number of advanced accelerator concepts (AAC) — their principles, technologies and potential applications. For the time being, none of them stands out as a definitive direction in which to go. But these novel ideas are in hot pursuit and look promising. Furthermore, some AAC requires a high power laser system. This has the ...

The Proceedings of Joint 28th ICFA Advanced Beam Dynamics and Advanced Nova Accelerator Workshops on Quantum Aspects of Beam Physics

International Nuclear Information System (INIS)

Chen, P

2004-01-01

The Joint 28th ICFA (International Committee for Future Accelerators) Advanced Beam Dynamics and Advanced and Novel Accelerators Workshop on ''QUANTUM ASPECTS OF BEAM PHYSICS and Other Critical Issues of Beams in Physics and Astrophysics'', was held on January 7-11, 2003, in Hiroshima, Japan. This was the third in the QABP workshop series. The first QABP workshop was launched in January 1998, in Monterey, California, and the second was held in October 2000, in Capri, Italy. Over the past five years, this workshop series has passed its torch around the world, from the U.S. to Europe, and this time to Japan in Asia. Following the footsteps of the first two workshops, this one in Hiroshima was again a tremendous success. The frontier of beam research points to increasingly higher energy, greater brightness and lower emittance beams with ever-increasing particle species. These demands have triggered a rapidly growing number of beam phenomena that involve quantum effects. With the significant advancement of laser and accelerator technologies, there is also a growing interest in using high energy, high intensity particle and photon beams for laboratory astrophysics investigations, as well as the application of beam physics expertise to astrophysics studies. It has therefore become a tradition that this workshop series attracted a broad spectrum of experts from beam physics, astrophysics, cosmology, particle physics, condensed matter physics, nuclear physics, atomic physics, and laser science, to explore a common frontier where their individual expertise and interests overlapped

CEBAF/SURA [Continuous Electron Beam Accelerator Facility]/[Southeastern Universities Research Association] 1987 summer workshop

International Nuclear Information System (INIS)

Gross, F.; Williamson, C.

1987-10-01

This report contains papers from the CEBAF accelerator facility summer workshop. Some topics covered are: baryon-baryon interactions, deuteron form factors; neutron detection; high resolution spectrometers; nuclear strangeness; parity violation; photon-deuteron interactions; chemical reactions in ion sources; quantum chromodynamics; hypernuclear magnetic moments; and photoproduction of π + from 14 N

Proceedings of the Workshop on relativistic heavy ion physics at present and future accelerators

International Nuclear Information System (INIS)

Csoergoe, T.; Hegyi, S.; Lukacs, B.; Zimanyi, J.

1991-09-01

This volume contains the Proceedings of the Budapest Workshop on relativistic heavy ion physics at present and future accelerators. The topics includes experimental heavy ion physics, particle phenomenology, Bose-Einstein correlations, relativistic transport theory, quark-gluon plasma rehadronization, astronuclear physics, leptonpair production and intermittency. All contributions were indexed separately for the INIS database. (G.P.)

Experimental evaluation of the Skylab orbital workshop ventilation system concept

Science.gov (United States)

Allums, S. L.; Hastings, L. J.; Ralston, J. T.

1972-01-01

Extensive testing was conducted to evaluate the Orbital Workshop ventilation concept. Component tests were utilized to determine the relationship between operating characteristics at 1 and 0.34 atm. System tests were conducted at 1 atm within the Orbital Workshop full-scale mockup to assess delivered volumetric flow rate and compartment air velocities. Component tests with the Anemostat circular diffusers (plenum- and duct-mounted) demonstrated that the diffuser produced essentially equivalent airflow patterns and velocities in 1- and 0.34-atm environments. The tests also showed that the pressure drop across the diffuser could be scaled from 1 to 0.34 atm using the atmosphere pressure ratio. Fan tests indicated that the performance of a multiple, parallel-mounted fan cluster could be predicted by summing the single-fan flow rates at a given delta P.

Proceedings of the Workshop on Advanced Network and Technology Concepts for Mobile, Micro, and Personal Communications

Science.gov (United States)

Paul, Lori (Editor)

1991-01-01

The Workshop on Advanced Network and Technology Concepts for Mobile, Micro, and Personal Communications was held at NASA's JPL Laboratory on 30-31 May 1991. It provided a forum for reviewing the development of advanced network and technology concepts for turn-of-the-century telecommunications. The workshop was organized into three main categories: (1) Satellite-Based Networks (L-band, C-band, Ku-band, and Ka-band); (2) Terrestrial-Based Networks (cellular, CT2, PCN, GSM, and other networks); and (3) Hybrid Satellite/Terrestrial Networks. The proceedings contain presentation papers from each of the above categories.

Report on Workshop on Future Directions for Accelerator R&D at Fermilab

Energy Technology Data Exchange (ETDEWEB)

Shiltsev, V.; Church, M.; Spentzouris, P.; Chou, W.; /Fermilab

2009-09-01

Accelerator R&D has played a crucial role in enabling scientific discovery in the past century and will continue to play this role in the years to come. In the U.S., the Office of High Energy Physics of DOE's Office of Science is developing a plan for national accelerator R&D stewardship. Fermilab undertakes accelerator research, design, and development focused on superconducting radio-frequency (RF), superconducting magnet, beam cooling, and high intensity proton technologies. In addition, the Lab pursues comprehensive integrated theoretical concepts and simulations of complete future facilities on both the energy and intensity frontiers. At present, Fermilab (1) supplies integrated design concept and technology development for a multi-MW proton source (Project X) to support world-leading programs in long baseline neutrino and rare processes experiments; (2) plays a leading role in the development of ionization cooling technologies required for muon storage ring facilities at the energy (multi-TeV Muon Collider) and intensity (Neutrino Factory) frontiers, and supplies integrated design concepts for these facilities; and (3) carries out a program of advanced accelerator R&D (AARD) in the field of high quality beam sources, and novel beam manipulation techniques.

Summary Report of Working Group 6: Laser-Plasma Acceleration

International Nuclear Information System (INIS)

Leemans, Wim P.; Downer, Michael; Siders, Craig

2006-01-01

A summary is given of presentations and discussions in the Laser-Plasma Acceleration Working Group at the 2006 Advanced Accelerator Concepts Workshop. Presentation highlights include: widespread observation of quasi-monoenergetic electrons; good agreement between measured and simulated beam properties; the first demonstration of laser-plasma acceleration up to 1 GeV; single-shot visualization of laser wakefield structure; new methods for measuring <100 fs electron bunches; and new methods for 'machining' laser-plasma accelerator structures. Discussion of future direction includes: developing a roadmap for laser-plasma acceleration beyond 1 GeV; a debate over injection and guiding; benchmarking simulations with improved wake diagnostics; petawatt laser technology for future laser-plasma accelerators

Proceedings of the FNCA 2003 workshop on application of electron accelerator. Radiation system for thin film

International Nuclear Information System (INIS)

Yoshii, Fumio; Kume, Tamikazu

2004-06-01

'Forum for Nuclear Cooperation in Asia (FNCA) Workshop on Application of Electron Accelerator' was sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT) and co-hosted by Malaysian Institute for Nuclear Technology Research (MINT) and Japan Atomic Energy Research Institute (JAERI). It was held at the Legend Hotel, Kuala Lumpur, Malaysia from 18 to 22 August 2003. The Workshop was attended by 28 experts on application of electron accelerator from each of the participating countries, i.e., China, Indonesia, Korea, Malaysia, The Philippines, Thailand and Vietnam, and 5 participants from Japan. On the first day, a National Executive Management Seminar on Application of Electron Accelerator was held and attended by 87 participants. Total of 19 papers including Seminar lectures, invited papers on film treatment by electron beam, and country reports on EB irradiation system were presented. The major areas of interest of FNCA member states for cooperation were identified for application of low energy electron accelerator as liquid, thin film and granules. The flue gas and wastewater treatments were added to the above major areas. Based on the proposal from the participating countries, discussions were carried out to re-formulate the work plan of the project for three years until FY 2004. All manuscripts submitted by every speaker were included in the proceedings. The 19 of the presented papers are indexed individually. (J.P.N.)

Proceedings of the Oak Ridge Electron Linear Accelerator (ORELA) Workshop

International Nuclear Information System (INIS)

Dunn, M.E.

2006-01-01

The Oak Ridge National Laboratory (ORNL) organized a workshop at ORNL July 14-15, 2005, to highlight the unique measurement capabilities of the Oak Ridge Electron Linear Accelerator (ORELA) facility and to emphasize the important role of ORELA for performing differential cross-section measurements in the low-energy resonance region that is important for nuclear applications such as nuclear criticality safety, nuclear reactor and fuel cycle analysis, stockpile stewardship, weapons research, medical diagnosis, and nuclear astrophysics. The ORELA workshop (hereafter referred to as the Workshop) provided the opportunity to exchange ideas and information pertaining to nuclear cross-section measurements and their importance for nuclear applications from a variety of perspectives throughout the U.S. Department of Energy (DOE). Approximately 50 people, representing DOE, universities, and seven U.S. national laboratories, attended the Workshop. The objective of the Workshop was to emphasize the technical community endorsement for ORELA in meeting nuclear data challenges in the years to come. The Workshop further emphasized the need for a better understanding of the gaps in basic differential nuclear measurements and identified the efforts needed to return ORELA to a reliable functional measurement facility. To accomplish the Workshop objective, nuclear data experts from national laboratories and universities were invited to provide talks emphasizing the unique and vital role of the ORELA facility for addressing nuclear data needs. ORELA is operated on a full cost-recovery basis with no single sponsor providing complete base funding for the facility. Consequently, different programmatic sponsors benefit by receiving accurate cross-section data measurements at a reduced cost to their respective programs; however, leveraging support for a complex facility such as ORELA has a distinct disadvantage in that the programmatic funds are only used to support program

Proceedings of the Oak Ridge Electron Linear Accelerator (ORELA) Workshop

Energy Technology Data Exchange (ETDEWEB)

Dunn, M.E.

2006-02-27

The Oak Ridge National Laboratory (ORNL) organized a workshop at ORNL July 14-15, 2005, to highlight the unique measurement capabilities of the Oak Ridge Electron Linear Accelerator (ORELA) facility and to emphasize the important role of ORELA for performing differential cross-section measurements in the low-energy resonance region that is important for nuclear applications such as nuclear criticality safety, nuclear reactor and fuel cycle analysis, stockpile stewardship, weapons research, medical diagnosis, and nuclear astrophysics. The ORELA workshop (hereafter referred to as the Workshop) provided the opportunity to exchange ideas and information pertaining to nuclear cross-section measurements and their importance for nuclear applications from a variety of perspectives throughout the U.S. Department of Energy (DOE). Approximately 50 people, representing DOE, universities, and seven U.S. national laboratories, attended the Workshop. The objective of the Workshop was to emphasize the technical community endorsement for ORELA in meeting nuclear data challenges in the years to come. The Workshop further emphasized the need for a better understanding of the gaps in basic differential nuclear measurements and identified the efforts needed to return ORELA to a reliable functional measurement facility. To accomplish the Workshop objective, nuclear data experts from national laboratories and universities were invited to provide talks emphasizing the unique and vital role of the ORELA facility for addressing nuclear data needs. ORELA is operated on a full cost-recovery basis with no single sponsor providing complete base funding for the facility. Consequently, different programmatic sponsors benefit by receiving accurate cross-section data measurements at a reduced cost to their respective programs; however, leveraging support for a complex facility such as ORELA has a distinct disadvantage in that the programmatic funds are only used to support program

Planetary Science Education - Workshop Concepts for Classrooms and Internships

Science.gov (United States)

Musiol, S.; Rosenberg, H.; Rohwer, G.; Balthasar, H.; van Gasselt, S.

2014-12-01

the Martian surface and presented their results in the end. Extensive handouts and high-quality print material supplemented face-to-face exercises. For the future we plan to expand our workshop concepts, to give students the possibility of conducting a week-long internship with our Planetary Sciences research group.

Accelerating energy efficiency improvement in the public sector, using Energy Performance Contracting - a workshop on Nordic experiences and needs for improvements

Energy Technology Data Exchange (ETDEWEB)

Gottberg, Annika; Gode, Jenny; Axelsson, Ulrik

2009-08-15

This report provides documentation on a workshop on experiences of Energy Performance Contracting (EPC) in the Nordic countries, aiming to identify strengths, weaknesses and needs for improvements. The results of surveys undertaken to inform presentations and discussions at the workshop are reported. Furthermore, the outcomes of the discussions during the workshop and resulting recommend actions for different actors to further and accelerate the use of EPC in the public sector are reported. Target groups for this documentation are existing and potential EPC customers, providers and policy-makers

Results from the INMM International Workshop on Containment and Surveillance: Concepts for the 21st Century

International Nuclear Information System (INIS)

Pickett, Chris A.; Tolk, Keith M.; Keel, Frances; LaMontagne, Steve

2010-01-01

The Institute of Nuclear Materials Management (INMM) held an International Workshop on 'Containment and Surveillance: Concepts for the 21st Century' on June 6-11, 2010 at the Oak National Laboratory in Oak Ridge, Tennessee. The National Nuclear Security Administration Offices of Non-proliferation Research and Development and Office of Nuclear Safeguards sponsored the event. The workshop focused on determining concepts and needs for 21st century containment and surveillance (C/S) systems that support International Atomic Energy Agency safeguards and future arms control agreements. Panel discussions from subject matter experts and international practitioners provided the daily topical theme of the following areas of C/S: authentication, tagging, sealing, containment verification, and surveillance systems. Each panel discussion was followed with a question and answer session with the audience and an afternoon breakout session. The facilitated breakout sessions were used to compile and determine future needs. Individuals attending the workshop included C/S experts and practitioners; IAEA and arms control inspectors, technology providers, vendors, students and individuals with an interest in or desire to learn about future C/S system needs. The primary goal for the workshop was to produce a document that details the future research and development needs for C/S systems that support nuclear safeguards and arms control missions. This paper will present a compilation of the information obtained from breakout sessions at the workshop. (author)

Summary report: working group 2 on 'Plasma Based Acceleration Concepts'

International Nuclear Information System (INIS)

Esarey, E.; Leemans, W.P.

1998-01-01

A summary of the talks, papers and discussion sessions presented in the Working Group on Plasma Based Acceleration Concepts is given within the context of the progress towards a 1 GeV laser driven accelerator module. The topics covered within the Working Group were self-modulated laser wakefield acceleration, standard laser wakefield acceleration, plasma beat wave acceleration, laser guiding and wake excitation in plasma channels, plasma wakefield acceleration, plasma lenses and optical injection techniques for laser wakefield accelerators. An overview will be given of the present status of experimental and theoretical progress as well as an outlook towards the future physics and technological challenges for the development of an optimized accelerator module

Summary Report of Working Group 7: Muon Colliders and Advanced Concepts

Energy Technology Data Exchange (ETDEWEB)

Nagaitsev, Sergei [Fermilab; Berg, J.Scott [Brookhaven

2012-07-01

The primary subject of working group 7 at the 2012 Advanced Accelerator Concepts Workshop was muon accelerators for a muon collider or neutrino factory. Additionally, this working group included topics that did not fit well into other working groups. Two subjects were discussed by more than one speaker: lattices to create a perfectly integrable nonlinear lattice, and a Penning trap to create antihydrogen.

Proceedings of the 4th KEK mechanical engineering workshop. Research and development on the technology of the X-band accelerator fabrication

International Nuclear Information System (INIS)

Ueno, Kenji

2003-10-01

The fourth KEK Mechanical Engineering Workshop was held on April 17, 2003. The main subject was ''The Research and Development on the Technology of the X-band Accelerator Fabrication'', which is a part of the collaboration work of Accelerator Laboratory, ACC and Mechanical Engineering Center, MEC based on the joint X-band accelerator research of KEK and SLAC. The main topic of study in FY 2002 was the problem analysis, and seeking its counter-measures about pitting generated over the inner-surface of the accelerator cavities through high field tests. Therefore, to analyze and develop counter-measures for these pittings, manufacturing of several kinds of test accelerators and conducting analytical tests for the surface of cells have been mainly undertaken by ACC and MEC. On the other hand, basic studies of the cutting and bonding processes have shown effective results for the future production process through corroboration work with academic and industrial fields. Related scientists and engineers from various fields participated in this workshop and presented their works. As a keynote speech, Prof. Hitoshi Yamamoto, belonging to Tohoku University, presented ''The physics on linear collider'', and Assistant Prof. Nobukazu Toge, belonging to ACC of KEK, presented ''The Linear Collider Accelerator''. Also, as an invitation speech, former Prof. Nobuteru Hitomi, former Head of MEC, who was the originator of this workshop, and one of the leaders in X-band accelerator fabrication, presented ''The promotion and survey of fabrication technology on X-band accelerator''. These speeches were very instructive, and presented a chance to think about the direction of R and D in our project. Twenty-four papers, ten from KEK, including the keynote speech, seven from universities and seven from industrial companies, were presented and discussed ardently. Among the discussion, there was an opinion that a fast pace to establish mass-production technology is a major requirement for the

Proceedings of the 1st Workshop on Flavor Symmetries and Consequences in Accelerators and Cosmology

CERN Document Server

Meloni, D; Morisi, S; Pastor, S; Peinado, E; Valle, J W F; FLASY2011

2012-01-01

The main goals of the first "Workshop on FLAvor SYmmetries and consequences in accelerators and cosmology" (FLASY) was to summarize the theoretical status of flavor symmetries, bringing together young researchers in the field to stimulate discussions and new collaborations, with the aim of investigating possible new physics scenarios to be tested at the LHC, as well as in future neutrino, cosmology experiments and dark matter searches.

A new concept for accelerator driven transmutation of nuclear wastes

International Nuclear Information System (INIS)

Arthur, E.D.

1991-01-01

A new concept for an accelerator-driven transmutation system is described. The central feature of the concept is generation of intense fluxes of thermal neutrons. In the system all long-lived radionuclides comprising high-level nuclear waste can be transmuted efficiently. Transmutation takes place in a unique, low material inventory environment. Presently two principal areas are being investigated for application of the concept. The first is associated with cleanup of defense high-level waste at DOE sites such as Hanford. The second, longer term area involves production of electric power using a coupled accelerator-multiplying blanket system. This system would utilize natural thorium or uranium and would transmute long-lived components of high-level waste concurrently during operation. 5 refs., 5 figs

Proceedings of the FNCA 2002 workshop on application of electron accelerator. Radiation system for liquid samples

International Nuclear Information System (INIS)

Yoshii, Fumio; Kume, Tamikazu

2003-10-01

'Forum for Nuclear Cooperation in Asia (FNCA) Workshop on Application of Electron Accelerator' was sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT) and hosted by Japan Atomic Energy Research Institute (JAERI) and Japan Atomic Industry Forum (JAIF). It was held at the Takasaki Radiation Chemistry Research Establishment (TRCRE), JAERI, Takasaki, Japan from 16 to 20 December 2002. The attendants at the workshop were consisted of 13 experts on application of electron accelerator from each of the participating countries, i.e., China, Indonesia, Korea, Malaysia, the Philippines, Thailand and Vietnam, and 40 participants from Japan. A total of 18 papers including invited papers on liquid waste treatment by electron beam, reviews of the radiation systems, and designing and cost analysis of EB irradiation system were presented. The major areas of interest of FNCA countries for cooperation were identified for application of low energy electron accelerator as liquid, thin film and granules. The gas and wastewater treatments were added to the above major areas. Based on the proposal from the participating countries, discussions were carried out to re-formulate the work plan of the project for three years until FY 2004. All manuscripts submitted by every speaker were included in the proceedings. The 17 of the presented papers are indexed individually. (J.P.N.)

International Workshop on Linear Colliders 2010

CERN Multimedia

CERN. Geneva

2010-01-01

IWLC2010 International Workshop on Linear Colliders 2010ECFA-CLIC-ILC joint meeting: Monday 18 October - Friday 22 October 2010Venue: CERN and CICG (International Conference Centre Geneva, Switzerland) This year, the International Workshop on Linear Colliders organized by the European Committee for Future Accelerators (ECFA) will study the physics, detectors and accelerator complex of a linear collider covering both CLIC and ILC options.Contact Workshop Secretariat  IWLC2010 is hosted by CERN

Proceedings of the workshop on deuteron beam acceleration in the KEK 12 GeV PS

International Nuclear Information System (INIS)

Mori, Yoshiharu

1991-12-01

The acceleration of atomic nucleus beam with the 12 GeV proton synchrotron in National Laboratory for High Energy Physics (KEK-PS) has been demanded by the experimenters of nuclear physics, and there was the move to concretely realize it at the beginning of 1980, but actually it was not materialized up to now due to various circumstances. The reason that makes the acceleration even in light nuclear beam like deuterons difficult is various, but one is that the acceleration method considered so far particularly in a booster main ring is very complicated. Recently as one of the various proposals made from the viewpoint of the future utilization of the KEK-PS, that of using nuclear beam and the experiment with the PS-collider have been discussed, and the method of accelerating nuclear beam in the PS was reexamined. As the result, together with the technical progress such as ring RF and linear accelerator augmentation, the method with high realization possibility became to be proposed. This proceedings is the report of the first workshop on deutron acceleration held on February 20, 1991, to prepare for the experiment using deuteron beam. (K.I.)

Second ICFA workshop

International Nuclear Information System (INIS)

Anon.

1979-01-01

A summary is given of the topics discussed at the second ICFA Workshop on 'Possibilities and Limitations of Accelerators and Detectors'. High energy accelerators are discussed, particularly electron-positron and proton-antiproton colliders. (W.D.L.).

Design Concepts for Muon-Based Accelerators

Energy Technology Data Exchange (ETDEWEB)

Ryne, R. D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Berg, J. S. [Brookhaven National Lab. (BNL), Upton, NY (United States); Kirk, H. G. [Brookhaven National Lab. (BNL), Upton, NY (United States); Palmer, R. B. [Brookhaven National Lab. (BNL), Upton, NY (United States); Stratkis, D. [Brookhaven National Lab. (BNL), Upton, NY (United States); Alexahin, Y. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Bross, A. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Gollwitzer, K. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Mokhov, N. V. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Neuffer, D. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Palmer, M. A. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Yonehara, K. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Snopok, P. [IIT, Chicago, IL (United States); Bogacz, A. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Roberts, T. J. [Muons Inc., Batavia, IL (United States); Delahaye, J. -P. [SLAC National Accelerator Lab., Menlo Park, CA (United States)

2015-05-01

Muon-based accelerators have the potential to enable facilities at both the Intensity and the Energy Frontiers. Muon storage rings can serve as high precision neutrino sources, and a muon collider is an ideal technology for a TeV or multi-TeV collider. Progress in muon accelerator designs has advanced steadily in recent years. In regard to 6D muon cooling, detailed and realistic designs now exist that provide more than 5 order-of-magnitude emittance reduction. Furthermore, detector performance studies indicate that with suitable pixelation and timing resolution, backgrounds in the collider detectors can be significantly reduced, thus enabling high-quality physics results. Thanks to these and other advances in design & simulation of muon systems, technology development, and systems demonstrations, muon storage-ring-based neutrino sources and a muon collider appear more feasible than ever before. A muon collider is now arguably among the most compelling approaches to a multi-TeV lepton collider. This paper summarizes the current status of design concepts for muon-based accelerators for neutrino factories and a muon collider.

A Variable Energy CW Compact Accelerator for Ion Cancer Therapy

Energy Technology Data Exchange (ETDEWEB)

Johnstone, Carol J. [Fermilab; Taylor, J. [Huddersfield U.; Edgecock, R. [Huddersfield U.; Schulte, R. [Loma Linda U.

2016-03-10

Cancer is the second-largest cause of death in the U.S. and approximately two-thirds of all cancer patients will receive radiation therapy with the majority of the radiation treatments performed using x-rays produced by electron linacs. Charged particle beam radiation therapy, both protons and light ions, however, offers advantageous physical-dose distributions over conventional photon radiotherapy, and, for particles heavier than protons, a significant biological advantage. Despite recognition of potential advantages, there is almost no research activity in this field in the U.S. due to the lack of clinical accelerator facilities offering light ion therapy in the States. In January, 2013, a joint DOE/NCI workshop was convened to address the challenges of light ion therapy [1], inviting more than 60 experts from diverse fields related to radiation therapy. This paper reports on the conclusions of the workshop, then translates the clinical requirements into accelerat or and beam-delivery technical specifications. A comparison of available or feasible accelerator technologies is compared, including a new concept for a compact, CW, and variable energy light ion accelerator currently under development. This new light ion accelerator is based on advances in nonscaling Fixed-Field Alternating gradient (FFAG) accelerator design. The new design concepts combine isochronous orbits with long (up to 4m) straight sections in a compact racetrack format allowing inner circulating orbits to be energy selected for low-loss, CW extraction, effectively eliminating the high-loss energy degrader in conventional CW cyclotron designs.

Details and justifications for the MAP concept specification for acceleration above 63 GeV

Energy Technology Data Exchange (ETDEWEB)

Berg, J. Scott [Brookhaven National Lab. (BNL), Upton, NY (United States). Collider-Accelerator Dept.

2014-02-28

The Muon Accelerator Program (MAP) requires a concept specification for each of the accelerator systems. The Muon accelerators will bring the beam energy from a total energy of 63 GeV to the maximum energy that will fit on the Fermilab site. Justifications and supporting references are included, providing more detail than will appear in the concept specification itself.

Proceedings of 14th international workshop on Asian network for accelerator-driven system and nuclear transmutation technology (ADS-NTT 2016)

International Nuclear Information System (INIS)

Pyeon, Cheol Ho

2016-09-01

The proceedings describe the current status on research and development (R and D) of accelerator-driven system (ADS) and nuclear transmutation techniques (NTT), including nuclear data, accelerator techniques, Pb-Bi target, fuel technologies and reactor physics, in East Asian countries: China, Korea and Japan. The proceedings also include all presentation materials presented in 'the 14th International Workshop on Asian Network for ADS and NTT (ADS-NTT2016)' held at Mito, Japan on 5th September, 2016. The objective of this workshop is to make actual progress of ADS R and D especially in East Asian countries, as well as in European countries, through sharing mutual interests and conducting the information exchange each other. The report is composed of these following items: Presentation materials: ADS-NTT 2016. (author)

CEBAF/SURA [Continuous Electron Beam Accelerator Facility]/[Southeastern Universities Research Association] 1988 summer workshop

International Nuclear Information System (INIS)

Gross, F.; Lightbody, J.

1989-01-01

This report contains papers from a summer workshop of the continuous electron beam accelerator facility. Some topics of these papers are: spectrometers; electron scattering from deuterons; relativistic correlations in nuclear matter; pion production on 3 He and 3 H; quantum electrodynamic processes in crystals; 12 C(e,e'p) x reaction; deuteron polarization tensor and relativistic spin rotation; electromagnetic excitation of nuclei; electron distortion and structure functions in (e,e'p) reactions; and reaction mechanism of 4 He(e,e'p) 3 H

State workshop on shallow land burial and alternative disposal concepts: proceedings

International Nuclear Information System (INIS)

1984-10-01

Three of the major conclusions reached by state participants were the following: (1) Significant data gaps and information needs have to be addressed before timely state decisionmaking can be accomplished. State participants felt a generic cost/risk/benefit analysis for all viable alternatives would be useful and might best be performed by the federal government on behalf of the states. (2) Recognizing the imprecision in summarizing overall attitudes of the workshop participants, alternative disposal concepts that appear to be the most favorably perceived when rank ordered by critical factors are augered holes with liners, belowground vaults, earth mounded concrete bunkers, aboveground vaults and mined cavities. (3) The public appears to place greater confidence in disposal methods that incorporate man-made engineered barriers because of some past problems at closed shallow land burial facilities. Concern was expressed by workshop participants that the public may not consider the perceived risks associated with shallow land burial to be acceptable. In addition to the four 10 CFR Part 61, Subpart C performance objectives, public acceptance of risk was considered to be a critical factor by state officials in selecting a disposal technology. The states should take the lead in pursuing development-oriented analyses, such as detailed concept engineering and economic feasibility studies. It is not within the purview of NRC responsibility to undertake such studies

[International Panel on 14 MeV Intense Neutron Source Based on Accelerators for Fusion Materials Study

International Nuclear Information System (INIS)

Thoms, K.R.; Wiffen, F.W.

1991-01-01

Both travelers were members of a nine-person US delegation that participated in an international workshop on accelerator-based 14 MeV neutron sources for fusion materials research hosted by the University of Tokyo. Presentations made at the workshop reviewed the technology developed by the FMIT Project, advances in accelerator technology, and proposed concepts for neutron sources. One traveler then participated in the initial meeting of the IEA Working Group on High Energy, High Flux Neutron Sources in which efforts were begun to evaluate and compare proposed neutron sources; the Fourth FFTF/MOTA Experimenters' Workshop which covered planning and coordination of the US-Japan collaboration using the FFTF reactor to irradiate fusion reactor materials; and held discussions with several JAERI personnel on the US-Japan collaboration on fusion reactor materials

New Developments in the Simulation of Advanced Accelerator Concepts

International Nuclear Information System (INIS)

Paul, K.; Cary, J.R.; Cowan, B.; Bruhwiler, D.L.; Geddes, C.G.R.; Mullowney, P.J.; Messmer, P.; Esarey, E.; Cormier-Michel, E.; Leemans, W.P.; Vay, J.-L.

2008-01-01

Improved computational methods are essential to the diverse and rapidly developing field of advanced accelerator concepts. We present an overview of some computational algorithms for laser-plasma concepts and high-brightness photocathode electron sources. In particular, we discuss algorithms for reduced laser-plasma models that can be orders of magnitude faster than their higher-fidelity counterparts, as well as important on-going efforts to include relevant additional physics that has been previously neglected. As an example of the former, we present 2D laser wakefield accelerator simulations in an optimal Lorentz frame, demonstrating and gt;10 GeV energy gain of externally injected electrons over a 2 m interaction length, showing good agreement with predictions from scaled simulations and theory, with a speedup factor of ∼2,000 as compared to standard particle-in-cell.

Proceedings of 11th international workshop on Asian network for accelerator-driven system and nuclear transmutation technology (ADS+NTT 2013)

International Nuclear Information System (INIS)

Pyeon, Cheol Ho

2014-01-01

The proceedings describe the current status on research and development (R and D) of accelerator-driven system (ADS) and nuclear transmutation techniques (NTT), including nuclear data, accelerator techniques, Pb-Bi target, fuel technologies and reactor physics, in East Asian countries: Korea, China and Japan. The proceedings also include all presentation materials presented in 'the 11th International Workshop on Asian Network for ADS and NTT (ADS+NTT 2013)' held at the Seoul National University, Seoul, Korea on 12th and 13th December, 2013. The objective of this workshop is to make actual progress of ADS R and D especially in East Asian countries, as well as in European countries, through sharing mutual interests and conducting the information exchange each other. The report is composed of these following items: Presentation materials: ADS+NTT 2013. (author)

Proceedings of the DOE workshop on the role of a high-current accelerator in the future of nuclear medicine

International Nuclear Information System (INIS)

Moody, D.C.; Peterson, E.J.

1989-05-01

The meeting was prompted by recent problems with isotope availability from DOE accelerator facilities; these difficulties have resulted from conflicting priorities between physics experiments and isotope production activities. The workshop was a forum in which the nuclear medicine community, isotope producers, industry, and other interested groups could discuss issues associated with isotope availability (including continuous supply options), the role of DOE and industry in isotope production, and the importance of research isotopes to the future of nuclear medicine. The workshop participants endorsed DOE's presence in supplying radioisotopes for research purposes and recommended that DOE should immediately provide additional support for radionuclide production in the form of personnel and supplies, DOE should establish a policy that would allow income from sales of future ''routine'' radionuclide production to be used to support technicians, DOE should obtain a 70-MeV, 500-/mu/A variable-energy proton accelerator as soon as possible, and DOE should also immediately solicit proposals to evaluate the usefulness of a new or upgraded high-energy, high-current machine for production of research radionuclides. This proceedings volume is a summary of workshop sessions that explored the future radionuclide needs of the nuclear medicine community and discussed the DOE production capabilities that would be required to meet these needs

Proceedings of the DOE workshop on the role of a high-current accelerator in the future of nuclear medicine

Energy Technology Data Exchange (ETDEWEB)

Moody, D.C.; Peterson, E.J. (comps.)

1989-05-01

The meeting was prompted by recent problems with isotope availability from DOE accelerator facilities; these difficulties have resulted from conflicting priorities between physics experiments and isotope production activities. The workshop was a forum in which the nuclear medicine community, isotope producers, industry, and other interested groups could discuss issues associated with isotope availability (including continuous supply options), the role of DOE and industry in isotope production, and the importance of research isotopes to the future of nuclear medicine. The workshop participants endorsed DOE's presence in supplying radioisotopes for research purposes and recommended that DOE should immediately provide additional support for radionuclide production in the form of personnel and supplies, DOE should establish a policy that would allow income from sales of future ''routine'' radionuclide production to be used to support technicians, DOE should obtain a 70-MeV, 500-/mu/A variable-energy proton accelerator as soon as possible, and DOE should also immediately solicit proposals to evaluate the usefulness of a new or upgraded high-energy, high-current machine for production of research radionuclides. This proceedings volume is a summary of workshop sessions that explored the future radionuclide needs of the nuclear medicine community and discussed the DOE production capabilities that would be required to meet these needs.

Results from the 2010 INMM International Containment and Surveillance Workshop focused on Concepts for the 21st Century

International Nuclear Information System (INIS)

Pickett, Chris A.; Tolk, Keith M.; Keel, Frances; LaMontagne, Steve

2010-01-01

The Institute of Nuclear Materials Management (INMM) held an International Workshop on 'Containment and Surveillance: Concepts for the 21st Century' on June 6-11, 2010 at the Oak National Laboratory in Oak Ridge, Tennessee. The National Nuclear Security Administration Offices of Non-proliferation Research and Development and Office of Nuclear Safeguards sponsored the event. The workshop focused on determining concepts and needs for 21st century containment and surveillance (C/S) systems that support International Atomic Energy Agency safeguards and future arms control agreements. Panel discussions from subject matter experts and international practitioners provided the daily topical theme of the following areas of C/S: authentication, tagging, sealing, containment verification, and surveillance systems. Each panel discussion was followed with a question and answer session with the audience and an afternoon breakout session. The facilitated breakout sessions were used to compile and determine future needs. Individuals attending the workshop included C/S experts and practitioners; IAEA and arms control inspectors, technology providers, vendors, students and individuals with an interest in or desire to learn about future C/S system needs. The primary goal for the workshop was to produce a document that details the future research and development needs for C/S systems that support nuclear safeguards and arms control missions. This paper will present a compilation of the information obtained from breakout sessions at the workshop. (author)

The Accelerator Reliability Forum

CERN Document Server

Lüdeke, Andreas; Giachino, R

2014-01-01

A high reliability is a very important goal for most particle accelerators. The biennial Accelerator Reliability Workshop covers topics related to the design and operation of particle accelerators with a high reliability. In order to optimize the over-all reliability of an accelerator one needs to gather information on the reliability of many different subsystems. While a biennial workshop can serve as a platform for the exchange of such information, the authors aimed to provide a further channel to allow for a more timely communication: the Particle Accelerator Reliability Forum [1]. This contribution will describe the forum and advertise it’s usage in the community.

Studies of the mirrortron ion accelerator concept and its application to heavy-ion drivers

International Nuclear Information System (INIS)

Post, R.F.; Schwager, L.A.; Dougless, S.R.; Jones, B.R.; Lambert, M.A.; Larson, D.L.

1991-01-01

The Mirrortron accelerator is a plasma-based ion accelerator concept that, when implemented, should permit both higher acceleration gradients and higher peak-current capabilities than is possible with conventional induction-type accelerators. Control over the acceleration and focussing of an accelerated beam should approach that achieved in vacuum-field-based ion accelerators. In the Mirrortron a low density (10 10 to 10 11 cm -3 ) ''hot electron'' plasma is confined by a long solenoidal magnetic field capped by ''mirrors''. Acceleration of prebunched ions is accomplished by activating a series of fast-pulsed mirror coils spaced along the acceleration tube. The hot electrons, being repelled by mirror action, leave the plasma ions behind to create a localized region of high electrical gradient (up to of order 100 MV/m). At the Laboratory an experiment and analyses to elucidate the concept and its scaling laws as applied to heavy-ion drivers are underway and will be described. 4 refs., 5 figs

Concept for high-charge-state ion induction accelerators

International Nuclear Information System (INIS)

Logan, B.G.; Perry, M.D.; Caporaso, G.J.

1996-01-01

This work describes a particular concept for ion induction linac accelerators using high-charge-state ions produced by an intense, short pulse laser, and compares the costs of a modular driver system producing 6.5 MJ for a variety of ion masses and charge states using a simple but consistent cost model

Proceedings of 12th international workshop on Asian network for accelerator-driven system and nuclear transmutation technology (ADS+NTT 2014)

International Nuclear Information System (INIS)

Pyeon, Cheol Ho

2015-01-01

The proceedings describe the current status on research and development (R and D) of accelerator-driven system (ADS) and nuclear transmutation techniques (NTT), including nuclear data, accelerator techniques, Pb-Bi target, fuel technologies and reactor physics, in East Asian countries: China, Japan and Korea. The proceedings also include all presentation materials presented in 'the 12th International Workshop on Asian Network for ADS and NTT (ADS+NTT 2014)' held at the Institute of Nuclear Energy and Safety Technology, Chinese Academy of Sciences, Hefei, China on 15th and 16th December, 2014. The objective of this workshop is to make actual progress of ADS R and D especially in East Asian countries, as well as in European countries, through sharing mutual interests and conducting the information exchange each other. The report is composed of these following items: Presentation materials: ADS+NTT 2014. (author)

Pushing hard on the accelerator

Energy Technology Data Exchange (ETDEWEB)

Anon.

1987-09-15

The quest for new techniques to drive future generations of particle accelerators has been pushed hard in recent years, efforts having been highlighted by workshops in Europe, organized by the European Committee for Future Accelerators, and in the US. The latest ECFA Workshop on New Developments in Particle Acceleration Techniques, held at Orsay from 29 June to 4 July, showed how the initial frantic search for innovation is now maturing.

A Concept of Plasma Wake Field Acceleration Linear Collider (PWFA-LC)

International Nuclear Information System (INIS)

Seryi, Andrei; Hogan, Mark; Pei, Shilun; Raubenheimer, Tor; Tenenbaum, Peter; Katsouleas, Tom; Huang, Chengkun; Joshi, Chan; Mori, Warren; Muggli, Patric

2009-01-01

Plasma Wake-Field Acceleration (PWFA) has demonstrated acceleration gradients above 50 GeV/m. Simulations have shown drive/witness bunch configurations that yield small energy spreads in the accelerated witness bunch and high energy transfer efficiency from the drive bunch to the witness bunch, ranging from 30% for a Gaussian drive bunch to 95% for a shaped longitudinal profile. These results open the opportunity for a linear collider that could be compact, efficient and more cost effective that the present microwave technologies. A concept of a PWFA-based Linear Collider (PWFA-LC) has been developed and is described in this paper. The drive beam generation and distribution, requirements on the plasma cells, and optimization of the interaction region parameters are described in detail. The R and D steps needed for further development of the concept are also outlined.

Concepts and limitations of macroparticle accelerators using travelling magnetic waves

International Nuclear Information System (INIS)

Wipf, S.L.

1980-01-01

The concept of an accelerator using a travelling magnetic wave acting on magnetized projectiles is discussed. Although superconductors have a high potential as projectile material, their low critical temperature makes them unsuitable. Among ferromagnetic materials dysprosium seems to be superior. For stable suspension and guidance a high conductivity, preferably superconducting, guide sheet is necessary. Magnetic field gradients of 10 9 A/m 2 travelling at 10 6 m/s should be achievable using present state-of-the-art components; resulting accelerations are greater than or equal to 500 km/s 2 . A linear accelerator for final speeds of 50 km/s needs a length of 2.5 km. Guidance forces sufficient to produce acceleration of 2 x 10 6 m/s 2 allow circular accelerators of reasonable size to achieve hypervelocities for small (50 to 100 mg) projectiles. An accelerator of 170 m diameter would surpass the best results from light gas guns. Travelling waves suitable for accelerations of the order of 10 4 m/s 2 can be produced without switching, by means of flux displacing rotors, easily adapted to circular accelerators

Muon Acceleration Concepts for NuMAX: "Dual-use" Linac and "Dogbone" RLA

Science.gov (United States)

Bogacz, S. A.

2018-02-01

We summarize the current state of a concept for muon acceleration aimed at a future Neutrino Factory. The main thrust of these studies was to reduce the overall cost while maintaining performance by exploring the interplay between the complexity of the cooling systems and the acceptance of the accelerator complex. To ensure adequate survival for the short-lived muons, acceleration must occur at high average gradient. The need for large transverse and longitudinal acceptances drives the design of the acceleration system to an initially low RF frequency, e.g., 325 MHz, which is then increased to 650 MHz as the transverse size shrinks with increasing energy. High-gradient normal conducting RF cavities at these frequencies require extremely high peak-power RF sources. Hence superconducting RF (SRF) cavities are chosen. We consider two cost effective schemes for accelerating muon beams for a stageable Neutrino Factory: exploration of the so-called "dual-use" linac concept, where the same linac structure is used for acceleration of both H- and muons and, alternatively, an SRF-efficient design based on a multi-pass (4.5) "dogbone" RLA, extendable to multi-pass FFAG-like arcs.

Spiral 2 workshop

International Nuclear Information System (INIS)

2004-01-01

The accelerator and experimental facilities at GANIL will be transformed over the next 5-10 years. The centerpiece of the additions to the accelerator complex will be Spiral-2. This is the first phase of a new radioactive beam facility based on the ISOL principle. The main aim of Spiral-2 will be to produce intense, high quality beams of neutron-rich nuclei created in neutron-induced fission of heavy elements and accelerated by the existing CIME cyclotron. The principal aims of this workshop will be a) to publicize the new facilities, b) to discuss and define the science which might be carried out with them, c) to discuss the instrumentation and infrastructure required to exploit the new facilities and d) to help form collaborations of scientists wishing to design and construct the equipment needed to undertake the science programme. This document gathers most of the slides presented in the workshop

Spiral 2 workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The accelerator and experimental facilities at GANIL will be transformed over the next 5-10 years. The centerpiece of the additions to the accelerator complex will be Spiral-2. This is the first phase of a new radioactive beam facility based on the ISOL principle. The main aim of Spiral-2 will be to produce intense, high quality beams of neutron-rich nuclei created in neutron-induced fission of heavy elements and accelerated by the existing CIME cyclotron. The principal aims of this workshop will be a) to publicize the new facilities, b) to discuss and define the science which might be carried out with them, c) to discuss the instrumentation and infrastructure required to exploit the new facilities and d) to help form collaborations of scientists wishing to design and construct the equipment needed to undertake the science programme. This document gathers most of the slides presented in the workshop.

WORKSHOP: Radiofrequency superconductivity

Energy Technology Data Exchange (ETDEWEB)

Anon.

1984-10-15

The Second Workshop on Radiofrequency Superconductivity was held at CERN from 23-27 July, four years after the first, organized at Karlsruhe. 35 invited talks were presented to the about 80 participants from Australia, Brazil, Europe, Japan and the United States. For the first time, ten Laboratories operating or planning superconducting accelerators for heavy ions participated and shared their experience with the community proposing the use of superconducting accelerating sections for electron accelerators.

WORKSHOP: Radiofrequency superconductivity

International Nuclear Information System (INIS)

Anon.

1984-01-01

The Second Workshop on Radiofrequency Superconductivity was held at CERN from 23-27 July, four years after the first, organized at Karlsruhe. 35 invited talks were presented to the about 80 participants from Australia, Brazil, Europe, Japan and the United States. For the first time, ten Laboratories operating or planning superconducting accelerators for heavy ions participated and shared their experience with the community proposing the use of superconducting accelerating sections for electron accelerators

Plasma-based and novel accelerators

International Nuclear Information System (INIS)

Sugihara, Ryo; Nishida, Yasushi

1992-05-01

This publication is a collection of papers presented at Workshop on Plasma-Based and Novel Accelerators held at National Institute for Fusion Science, Nagoya, on December 19-20, 1991. Plasma-based accelerators are attracting considerable attention in these days a new, exciting field of plasma applications. The study gives rise to and spurs study of other unique accelerators like laser-based accelerators. The talks in the Workshop encompassed beat-wave accelerator (BWA), plasma wake field accelerator (PWFA), V p x B accelerator, laser-based accelerators and some novel methods of acceleration. They also covered the topics such as FEL, cluster acceleration and plasma lens. Small scale experiments as those in universities have exhibited brilliant results while larger scale experiments like BWA in Institute of Laser Engineering, Osaka University, and PWFA in KEK start showing significant results as well. (J.P.N.)

PREFACE: Joint IPPP Durham/Cockcroft Institute/ICFA Workshop on Advanced QED methods for Future Accelerators

Science.gov (United States)

Bailey, I. R.; Barber, D. P.; Chattopadhyay, S.; Hartin, A.; Heinzl, T.; Hesselbach, S.; Moortgat-Pick, G. A.

2009-11-01

The joint IPPP Durham/Cockcroft Institute/ICFA workshop on advanced QED methods for future accelerators took place at the Cockcroft Institute in early March 2009. The motivation for the workshop was the need for a detailed consideration of the physics processes associated with beam-beam effects at the interaction points of future high-energy electron-positron colliders. There is a broad consensus within the particle physics community that the next international facility for experimental high-energy physics research beyond the Large Hadron Collider at CERN should be a high-luminosity electron-positron collider working at the TeV energy scale. One important feature of such a collider will be its ability to deliver polarised beams to the interaction point and to provide accurate measurements of the polarisation state during physics collisions. The physics collisions take place in very dense charge bunches in the presence of extremely strong electromagnetic fields of field strength of order of the Schwinger critical field strength of 4.4×1013 Gauss. These intense fields lead to depolarisation processes which need to be thoroughly understood in order to reduce uncertainty in the polarisation state at collision. To that end, this workshop reviewed the formalisms for describing radiative processes and the methods of calculation in the future strong-field environments. These calculations are based on the Furry picture of organising the interaction term of the Lagrangian. The means of deriving the transition probability of the most important of the beam-beam processes - Beamsstrahlung - was reviewed. The workshop was honoured by the presentations of one of the founders, V N Baier, of the 'Operator method' - one means for performing these calculations. Other theoretical methods of performing calculations in the Furry picture, namely those due to A I Nikishov, V I Ritus et al, were reviewed and intense field quantum processes in fields of different form - namely those

Proc. of the workshop on pushing the limits of RF superconductivity.

Energy Technology Data Exchange (ETDEWEB)

Kim, K-J., Eyberger, C., editors

2005-04-13

For three days in late September last year, some sixty experts in RF superconductivity from around the world came together at Argonne to discuss how to push the limits of RF superconductivity for particle accelerators. It was an intense workshop with in-depth presentations and ample discussions. There was added excitement due to the fact that, a few days before the workshop, the International Technology Recommendation Panel had decided in favor of superconducting technology for the International Linear Collider (ILC), the next major high-energy physics accelerator project. Superconducting RF technology is also important for other large accelerator projects that are either imminent or under active discussion at this time, such as the Rare Isotope Accelerator (RIA) for nuclear physics, energy recovery linacs (ERLs), and x-ray free-electron lasers. For these accelerators, the capability in maximum accelerating gradient and/or the Q value is essential to limit the length and/or operating cost of the accelerators. The technological progress of superconducting accelerators during the past two decades has been truly remarkable, both in low-frequency structures for acceleration of protons and ions as well as in high-frequency structures for electrons. The requirements of future accelerators demand an even higher level of performance. The topics of this workshop are therefore highly relevant and timely. The presentations given at the workshop contained authoritative reviews of the current state of the art as well as some original materials that previously had not been widely circulated. We therefore felt strongly that these materials should be put together in the form of a workshop proceeding. The outcome is this report, which consists of two parts: first, a collection of the scholarly papers prepared by some of the participants and second, copies of the viewgraphs of all presentations. The presentation viewgraphs, in full color, are also available from the Workshop

Separations technology development to support accelerator-driven transmutation concepts

International Nuclear Information System (INIS)

Venneri, F.; Arthur, E.; Bowman, C.

1996-01-01

This is the final report of a one-year Laboratory-Directed Research and Development (LDRD) Project at the Los Alamos National Laboratory (LANL). This project investigated separations technology development needed for accelerator-driven transmutation technology (ADTT) concepts, particularly those associated with plutonium disposition (accelerator-based conversion, ABC) and high-level radioactive waste transmutation (accelerator transmutation of waste, ATW). Specific focus areas included separations needed for preparation of feeds to ABC and ATW systems, for example from spent reactor fuel sources, those required within an ABC/ATW system for material recycle and recovery of key long-lived radionuclides for further transmutation, and those required for reuse and cleanup of molten fluoride salts. The project also featured beginning experimental development in areas associated with a small molten-salt test loop and exploratory centrifugal separations systems

Proceedings of the workshops on the utilization of electron beams

International Nuclear Information System (INIS)

Sato, Shoichi

1993-09-01

Workshops organized by JAERI in cooperation with OAEP, BATAN and JAIF on the utilization of electron beam (EB) were held in Bangkok and Jakarta on 9 and 13 July 1992, respectively. The proceedings contain 13 papers presented at the Workshops. Welcome remarks, opening address and closing remarks are also recorded. At the first part of the Workshops, general view on the application of electron accelerators and introduction of electron accelerators were made. Potential applications of electron accelerators to polymer processing, sterilization of medical products, flue gas purification, treatment of wastewater and sewage sludge and bioresources were introduced from Japanese participants. Potential application of electron accelerators to polymer processing and food irradiation in Thailand and Indonesia were also discussed. (author)

High Field Workshop

Energy Technology Data Exchange (ETDEWEB)

Anon.

1984-12-15

A Workshop was held in Frascati at the end of September under the title 'Generation of High Fields for Particle Acceleration to Very High Energies'. It was organized by the CERN Accelerator School, the European Committee for Future Accelerators (ECFA) and the Italian INFN and was a further stage in the exploratory moves towards new techniques of acceleration. Such techniques might become necessary to respond to the needs of high energy physics some decades from now when the application of conventional techniques will probably have reached their limits.

Applications of ion beam analysis workshop. Workshop handbook

International Nuclear Information System (INIS)

1995-01-01

A workshop on applications of ion beam analysis was held at ANSTO, immediate prior to the IBMM-95 Conference in Canberra. It aims was to review developments and current status on use of ion beams for analysis, emphasizing the following aspects: fundamental ion beam research and secondary effects of ion beams; material sciences, geological, life sciences, environmental and industrial applications; computing codes for use in accelerator research; high energy heavy ion scattering and recoil; recent technological development using ion beams. The handbook contains the workshop's program, 29 abstracts and a list of participants

Concept of an accelerator-driven subcritical research reactor within the TESLA accelerator installation

International Nuclear Information System (INIS)

Pesic, Milan; Neskovic, Nebojsa

2006-01-01

Study of a small accelerator-driven subcritical research reactor in the Vinca Institute of Nuclear Sciences was initiated in 1999. The idea was to extract a beam of medium-energy protons or deuterons from the TESLA accelerator installation, and to transport and inject it into the reactor. The reactor core was to be composed of the highly enriched uranium fuel elements. The reactor was designated as ADSRR-H. Since the use of this type of fuel elements was not recommended any more, the study of a small accelerator-driven subcritical research reactor employing the low-enriched uranium fuel elements began in 2004. The reactor was designated as ADSRR-L. We compare here the results of the initial computer simulations of ADSRR-H and ADSRR-L. The results have confirmed that our concept could be the basis for designing and construction of a low neutron flux model of the proposed accelerator-driven subcritical power reactor to be moderated and cooled by lead. Our objective is to study the physics and technologies necessary to design and construct ADSRR-L. The reactor would be used for development of nuclear techniques and technologies, and for basic and applied research in neutron physics, metrology, radiation protection and radiobiology

Advanced Accelerator Concepts

Science.gov (United States)

Siemann, Robert

1998-04-01

Current particle accelerators rely on conventional or superconducting radio frequency cavities to accelerate beams of protons or electrons for nuclear and particle research and for medical and materials science studies. New methods for achieving larger accelerating gradients have been proposed and are being studied. These include the use of high power lasers, laser driven plasmas, wake fields generated by intense low energy beams, and millimeter wavelength EM structures. The studies to date, and the prospects for practical applications of these new ideas will be discussed.

The proof-of-concept experiment for the spiral line induction accelerator

Energy Technology Data Exchange (ETDEWEB)

Putnam, S D; Bailey, V L; Smith, J; Lidestri, J; Thomas, H; Lackner, H; Nishimoto, H [Pulse Sciences, Inc., San Leandro, CA (United States)

1997-12-31

A proof-of-concept experiment (POCE) for the Spiral Line Induction Accelerator (SLIA) is underway at Pulse Sciences, Inc. to demonstrate a new compact high current ({>=} few kiloamperes) recirculating induction accelerator for high power ({>=} 100 kW) commercial processing and other applications. Hardware has been fabricated to generate 9.5 MeV electron beams at 2 and 10 kA by recirculating the beam for two passes through each of two 1.5 MeV accelerating units. Initial experiments have demonstrated acceleration of 2 and 10 kA beams to 5.5 MeV by transport around a complete turn with two passes through a single accelerating unit and work is currently in progress to complete the full POCE. Experimental results to date are reported. (author). 5 figs., 14 refs.

CARE-HHH-APD Workshop on Finalizing the Roadmap for the Upgrade of the CERN and GSI Accelerator Complex

CERN Document Server

Zimmermann, Frank; BEAM'07; BEAM 2007; Finalizing the Roadmap for the Upgrade of the LHC and GSI Accelerator Complex

2008-01-01

This report contains the Proceedings of the CARE-HHH-APD Event BEAM’07, “Finalizing the Roadmap for the Upgrade of the CERN & GSI Accelerator Complex,” which was held at CERN in Geneva, Switzerland, from 1 to 5 October 2007. BEAM’07 was primarily devoted to beam dynamics limitations for the two, or three, alternative baseline scenarios of the LHC luminosity upgrade and to critical design choices for the upgrade of the LHC injector complex at CERN and for the FAIR complex at GSI. It comprised five parts: (1) a Mini-Workshop on LHC+ Beam Performance, (2) a CERN-GSI Meeting on Collective Effects, (3) the Francesco Ruggiero Memorial Symposium, (4) a Mini-Workshop on the LHC Injectors Upgrade, and (5) the BEAM’07 Summaries. Topics addressed in the first mini-workshop of BEAM’07 ranged from the luminosity performance reach of the upgraded LHC in different scenarios, over the generation and stability of the future LHC beams, the turnaround time, beam–beam effects, luminosity levelling methods, and ...

Accelerating Scientific Advancement for Pediatric Rare Lung Disease Research. Report from a National Institutes of Health-NHLBI Workshop, September 3 and 4, 2015.

Science.gov (United States)

Young, Lisa R; Trapnell, Bruce C; Mandl, Kenneth D; Swarr, Daniel T; Wambach, Jennifer A; Blaisdell, Carol J

2016-12-01

Pediatric rare lung disease (PRLD) is a term that refers to a heterogeneous group of rare disorders in children. In recent years, this field has experienced significant progress marked by scientific discoveries, multicenter and interdisciplinary collaborations, and efforts of patient advocates. Although genetic mechanisms underlie many PRLDs, pathogenesis remains uncertain for many of these disorders. Furthermore, epidemiology and natural history are insufficiently defined, and therapies are limited. To develop strategies to accelerate scientific advancement for PRLD research, the NHLBI of the National Institutes of Health convened a strategic planning workshop on September 3 and 4, 2015. The workshop brought together a group of scientific experts, intramural and extramural investigators, and advocacy groups with the following objectives: (1) to discuss the current state of PRLD research; (2) to identify scientific gaps and barriers to increasing research and improving outcomes for PRLDs; (3) to identify technologies, tools, and reagents that could be leveraged to accelerate advancement of research in this field; and (4) to develop priorities for research aimed at improving patient outcomes and quality of life. This report summarizes the workshop discussion and provides specific recommendations to guide future research in PRLD.

Workshop Summary Proceedings Document: G7 Alliance on Resource Efficiency: U.S.-hosted Workshop on the Use of Life Cycle Concepts in Supply Chain Management to Achieve Resource Efficiency

Science.gov (United States)

This proceedings document summarizes prepared remarks, presentations and discussions from the G7 Alliance on Resource Efficiency: U.S.-hosted Workshop on the Use of Life Cycle Concepts in Supply Chain Management to Achieve Resource Efficiency.

Program for Plasma-Based Concepts for Future High Energy Accelerators

International Nuclear Information System (INIS)

Katsouleas, Thomas C.; Muggli, Patric

2003-01-01

OAK B204 Program for Plasma-Based Concepts for Future High Energy Accelerators. The progress made under this program in the period since November 15, 2002 is reflected in this report. The main activities for this period were to conduct the first run of the E-164 high-gradient wakefield experiment at SLAC, to prepare for run 2 and to continue our collaborative effort with CERN to model electron cloud interactions in circular accelerators. Each of these is described. Also attached to this report are papers that were prepared or appeared during this period

Accelerator breeder concept

International Nuclear Information System (INIS)

Bartholomew, G.A.; Fraser, J.S.; Garvey, P.M.

1978-10-01

The principal components and functions of an accelerator breeder are described. The role of the accelerator breeder as a possible long-term fissile production support facility for CANDU (Canada Deuterium Uranium) thorium advanced fuel cycles and the Canadian research and development program leading to such a facility are outlined. (author)

Report on high energy neutron dosimetry workshop

International Nuclear Information System (INIS)

Alvar, K.R.; Gavron, A.

1993-01-01

The workshop was called to assess the performance of neutron dosimetry per the responses from ten DOE accelerator facilities to an Office of Energy Research questionnaire regarding implementation of a personnel dosimetry requirement in DRAFT DOE 5480.ACC, ''Safety of Accelerator Facilities''. The goals of the workshop were to assess the state of dosimetry at high energy accelerators and if such dosimetry requires improvement, to reach consensus on how to proceed with such improvements. There were 22 attendees, from DOE Programs and contract facilities, DOE, Office of Energy Research (ER), Office of Environmental Safety and Health (EH), Office of Fusion Energy, and the DOE high energy accelerator facilities. A list of attendees and the meeting agenda are attached. Copies of the presentations are also attached

Workshop on Electron-Cloud Simulations for Proton and Positron Beams (ECLOUD'02) organized by the SL Accelerator Physics Group at CERN.

CERN Multimedia

Patrice Loïez

2002-01-01

This workshop was organized by the SL Accelerator Physics group at CERN from 15 to 18 April 2002. More than 60 participants from 17 institutes reflect the great worldwide interest in the electron-cloud phenomenon, which presently limits the performance of several storage rings and has become a concern for the LHC.

Developing workshop module of realistic mathematics education: Follow-up workshop

Science.gov (United States)

Palupi, E. L. W.; Khabibah, S.

2018-01-01

Realistic Mathematics Education (RME) is a learning approach which fits the aim of the curriculum. The success of RME in teaching mathematics concepts, triggering students’ interest in mathematics and teaching high order thinking skills to the students will make teachers start to learn RME. Hence, RME workshop is often offered and done. This study applied development model proposed by Plomp. Based on the study by RME team, there are three kinds of RME workshop: start-up workshop, follow-up workshop, and quality boost. However, there is no standardized or validated module which is used in that workshops. This study aims to develop a module of RME follow-up workshop which is valid and can be used. Plopm’s developmental model includes materials analysis, design, realization, implementation, and evaluation. Based on the validation, the developed module is valid. While field test shows that the module can be used effectively.

2016 FACET-II Science Workshop Summary Report

Energy Technology Data Exchange (ETDEWEB)

Hogan, Mark J., ed.

2017-07-19

The second in a series of FACET-II Science Workshops was held at SLAC National Accelerator Laboratory on October 17-19, 2016 [1]. The workshop drew thirty-five participants from eighteen different institutions including CERN, DESY, Ecole Polytechnique, FNAL, JAI, LBNL, LLNL, Radiabeam, Radiasoft, SLAC, Stony Brook, Strathclyde, Tech-X, Tsinghua, UC Boulder, UCLA and UT Austin. The 2015 workshop [2, 3] helped prioritize research directions for FACET-II. The 2016 workshop was focused on understanding what improvements are needed at the facility to support the next generation of experiments. All presentations are linked to the workshop website as a permanent record.

Workshop on CEBAF [Continuous Electron Beam Accelerator Facility] spectrometer magnet design and technology: Proceedings

International Nuclear Information System (INIS)

1986-09-01

The planned experimental program at CEBAF includes high-resolution, large acceptance spectrometers and a large toroidal magnetic, detector. In order to take full advantage of the high quality beam characteristics, the performances required will make these devices quite unique instruments compared to existing facilities in the same energy range. Preliminary designs have shown that such performances can be reached, but key questions concerning design concepts and most appropriate and cost-effective technologies had to be answered before going further with the designs. It was the purpose of the Workshop on CEBAF Spectrometer Magnet Design and Technology, organized by the CEBAF Research and Engineering Divisions, to provide the most complete information about the state-of-the-art tools and techniques in magnet design and construction and to discuss the ones most appropriate to the CEBAF spectrometers. In addition, it is expected that this Workshop will be the staring point for further interactions and collaborations between international magnet experts and the CEBAF staff, during the whole process of designing and building the spectrometers

Review of the SLAC and Les Houches workshops

International Nuclear Information System (INIS)

Prescott, C.Y.

1994-12-01

Polarized Electron Source workshops have been held at varying intervals, beginning in 1983 when Charles Sinclair convened the first at SLAC. Since that time, three workshops were held in conjunction with the International Spin Symposia and two at other occasions. The increasing importance of polarized electron beams at accelerators has stimulated interest in these workshops. Two workshops have been held since the last International Spin Symposium in Nagoya. In 1993, a workshop was held at SLAC, and in 1994 at Les Houches, a polarized electron beam session was held as part of a polarized beam and targets workshop. This report summarizes highlights from the latter two workshops

First workshop on the possibilities of biorefinery concepts for the industry : held at hotel "De Wageningse Berg", Wageningen, the Netherlands (16 June 2006) : official minutes

NARCIS (Netherlands)

Annevelink, E.; Jong, de E.; Ree, van R.; Zwart, R.W.R.

2006-01-01

On June the 16th the first ¿workshop on the possibilities of biorefinery concepts for the industry¿ was held, bringing together different Dutch stakeholders, and addressing common as well as conflicting technical and market issues with regard to biorefinery opportunities. The first-of-akind workshop

Design concept of radiation control system for the high intensity proton accelerator facility

Energy Technology Data Exchange (ETDEWEB)

Miyamoto, Yukihiro; Ikeno, Koichi; Akiyama, Shigenori; Harada, Yasunori [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2002-11-01

Description is given for the characteristic radiation environment for the High Intensity Proton Accelerator Facility and the design concept of the radiation control system of it. The facility is a large scale accelerator complex consisting of high energy proton accelerators carrying the highest beam intensity in the world and the related experimental facilities and therefore provides various issues relevant to the radiation environment. The present report describes the specifications for the radiation control system for the facility, determined in consideration of these characteristics. (author)

RADIOFREQUENCY SUPERCONDUCTIVITY: Workshop

International Nuclear Information System (INIS)

Lengeler, Herbert

1989-01-01

Superconducting radiofrequency is already playing an important role in the beam acceleration system for the TRISTAN electron-positron collider at the Japanese KEK Laboratory and new such systems are being prepared for other major machines. Thus the fourth Workshop on Radiofrequency Superconductivity, organized by KEK under the chairmanship of local specialist Yuzo Kojima and held just before the International Conference on High Energy Accelerators, had much progress to review and even more to look forward to

Methodology of gender research and local development concepts: report on workshop, 11-12 November 1999

OpenAIRE

Klein-Hessling, Ruth

2000-01-01

Der Workshop "Methodology of Gender Research and Local Development Concepts" wurde aus Anlass eines Besuches zweier Angehöriger der 'Ahfad University of Women' Omdurmman, Sudan von der 'Gender Division of the Sociology of Development Research Centre' an der Universität Bielefeld organisiert und von ungefähr 30 Teilnehmern besucht. Erfahrungen von empirischen Feldforschungsarbeiten aus dem Sudan, Kenia, Ruanda, Westafrika und Südasien bildeten den Ausgangspunkt für Diskussionen über methodolo...

Architectures, Concepts and Architectures for Service Oriented Computing : proceedings of the 1st International Workshop - ACT4SOC 2007

NARCIS (Netherlands)

van Sinderen, Marten J.; Unknown, [Unknown

2007-01-01

This volume contains the proceedings of the First International Workshop on Architectures, Concepts and Technologies for Service Oriented Computing (ACT4SOC 2007), held on July 22 in Barcelona, Spain, in conjunction with the Second International Conference on Software and Data Technologies (ICSOFT

Linear accelerator: A concept

Science.gov (United States)

Mutzberg, J.

1972-01-01

Design is proposed for inexpensive accelerometer which would work by applying pressure to fluid during acceleration. Pressure is used to move shuttle, and shuttle movement is sensed and calibrated to give acceleration readings.

2nd Topical Workshop on Laser Technology and Optics Design

CERN Document Server

2013-01-01

Lasers have a variety of applications in particle accelerator operation and will play a key role in the development of future particle accelerators by improving the generation of high brightness electron and exotic ion beams and through increasing the acceleration gradient. Lasers will also make an increasingly important contribution to the characterization of many complex particle beams by means of laser-based beam diagnostics methods. The second LANET topical workshop will address the key aspects of laser technology and optics design relevant to laser application to accelerators. The workshop will cover general optics design, provide an overview of different laser sources and discuss methods to characterize beams in details. Participants will be able to choose from a range of topical areas that go deeper in more specific aspects including tuneable lasers, design of transfer lines, noise sources and their elimination and non-linear optics effects. The format of the workshop will be mainly training-based wit...

A Report on the Workshop on the Uses and Generation of Femtosecond Radiation

International Nuclear Information System (INIS)

Jackson, A.

1998-01-01

We describe the proceedings of the Workshop on the Uses and Generation of Femtosecond Radiation, held at the E.O. Lawrence Berkeley National Laboratory (LBNL), in February 1998, and some of the ideas that were generated subsequent to the workshop. The motivation for this workshop was to bring together accelerator physicists interested in the generation of ultra-short (< 200 fs) pulses of XUV and x-ray radiation, and scientists interested in using them. The primary purpose of the workshop was to educate the accelerator physicists about the source characteristics necessary to carry out specific experiments, and to inform the user community of ideas currently being explored by the accelerator community. A second objective was to develop a set of parameters and requirements that could form the basis for a broad-based femtoscience user facility. In this paper we describe some of the ideas and techniques that accelerator physicists are pursuing to ilfill the diverse requirements of this expanding community

Proceedings of the Fifth International Workshop on Targetry and Target Chemistry

International Nuclear Information System (INIS)

Dahl, J.R.; Ferrieri, R.; Finn, R.; Schlyer, D.J.

1994-01-01

The goal of the International Workshop on Targetry and Target Chemistry series has always been to provide an open forum for discussion of medical radionuclide production, primarily with particle accelerators. The format is intended to encourage the participants to set the direction of the ensuing discussion, allowing the participants to focus on areas of greatest immediate interest. The preceding workshops have set this tone and this workshop was designed to continue in this spirit. The topics of each session were selected by the local organizing committee after discussion with many of the attendees of the previous workshops. The formality of the workshops has gradually increased from the first rather small, very informal gathering in Heidelburg to the larger contingent present in Villigen, but the open discussion of topics of preoccupation has been maintained. Each Workshop has had areas of particular fascination. In the Fifth workshop the major focus was on the development of new accelerators and on the production of ammonia. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

Proceedings of the Fifth International Workshop on Targetry and Target Chemistry

Energy Technology Data Exchange (ETDEWEB)

Dahl, J.R.; Ferrieri, R.; Finn, R.; Schlyer, D.J. [eds.

1994-12-31

The goal of the International Workshop on Targetry and Target Chemistry series has always been to provide an open forum for discussion of medical radionuclide production, primarily with particle accelerators. The format is intended to encourage the participants to set the direction of the ensuing discussion, allowing the participants to focus on areas of greatest immediate interest. The preceding workshops have set this tone and this workshop was designed to continue in this spirit. The topics of each session were selected by the local organizing committee after discussion with many of the attendees of the previous workshops. The formality of the workshops has gradually increased from the first rather small, very informal gathering in Heidelburg to the larger contingent present in Villigen, but the open discussion of topics of preoccupation has been maintained. Each Workshop has had areas of particular fascination. In the Fifth workshop the major focus was on the development of new accelerators and on the production of ammonia. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Post-accelerator issues at the IsoSpin Laboratory

International Nuclear Information System (INIS)

Chattopadhyay, S.; Nitschke, J.M.

1994-05-01

The workshop on ''Post-Accelerator Issues at the Isospin Laboratory'' was held at the Lawrence Berkeley Laboratory from October 27--29, 1993. It was sponsored by the Center for Beam Physics in the Accelerator and Fusion Research Division and the ISL Studies Group in the Nuclear Science Division. About forty scientists from around the world participated vigorously in this two and a half day workshop, (c.f. Agenda, Appendix D). Following various invited review talks from leading practitioners in the field on the first day, the workshop focussed around two working groups: (1) the Ion Source and Separators working group and (2) the Radio Frequency Quadrupoles and Linacs working group. The workshop closed with the two working groups summarizing and outlining the tasks for the future. This report documents the proceedings of the workshop and includes the invited review talks, the two summary talks from the working groups and individual contributions from the participants. It is a complete assemblage of state-of-the-art thinking on ion sources, low-β, low(q/A) accelerating structures, e.g. linacs and RFQS, isobar separators, phase-space matching, cyclotrons, etc., as relevant to radioactive beam facilities and the IsoSpin Laboratory. We regret to say that while the fascinating topic of superconducting low-velocity accelerator structure was covered by Dr. K. Shepard during the workshop, we can only reproduce the copies of the transparencies of his talk in the Appendix, since no written manuscript was available at the time of publication of this report. The individual report have been catologed separately elsewhere

Target conception for the Munich fission fragment accelerator

CERN Document Server

Maier, H J; Gross, M L; Grossmann, R; Kester, O; Thirolf, P

1999-01-01

For the new high-flux reactor FRM II, the fission fragment accelerator MAFF is under design. MAFF will supply intense mass-separated radioactive ion beams of very neutron-rich nuclei with energies around the Coulomb barrier. A central part of this accelerator is the ion source with the fission target, which is operated at a neutron flux of 1.5x10 sup 1 sup 4 cm sup - sup 2 s sup - sup 1. The target consists of typically 1 g of sup 2 sup 3 sup 5 U dispersed in a cylindrical graphite matrix, which is encapsulated in a Re container. To enable diffusion and extraction of the fission products, the target has to be maintained at a temperature of up to 2400 deg. C during operation. It has to stand this temperature for at least one reactor cycle of 1250 h. Comprehensive tests are required to study the long-term behaviour of the involved materials at these conditions prior to operation in the reactor. The present paper gives details of the target conception and the projected tests.

Second Quaternary dating workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-11-01

The second Quaternary dating methods workshop was held at Lucas Heights and sponsored by ANSTO and AINSE. Topics covered include, isotope and thermoluminescence dating, usage of accelerator and thermal ionisation mass spectrometry in environmental studies emphasizing on the methodologies used and sample preparation

Second Quaternary dating workshop

International Nuclear Information System (INIS)

1999-01-01

The second Quaternary dating methods workshop was held at Lucas Heights and sponsored by ANSTO and AINSE. Topics covered include, isotope and thermoluminescence dating, usage of accelerator and thermal ionisation mass spectrometry in environmental studies emphasizing on the methodologies used and sample preparation

Workshop on Subcritical Neutron Production

International Nuclear Information System (INIS)

Walter Sadowski; Roald Sagdeev

2006-01-01

Executive Summary of the Workshop on Subcritical Neutron Production A workshop on Subcritical Neutron Production was sponsored by the East-West Center of the University of Maryland on October 11-13, 2004. The subject of the workshop was the application of subcritical neutrons to transmutation of actinides. The workshop was attended by members of the fission, accelerator and fusion communities. Papers on the state of development of neutron production by accelerators, fusion devices, and fission reactors were presented. Discussions were held on the potential of these technologies to solve the problems of spent nuclear waste storage and nuclear non-proliferation presented by current and future nuclear power reactors. A list of participants including their affiliation and their E-Mail addresses is attached. The workshop concluded that the technologies, presently available or under development, hold out the exciting possibility of improving the environmental quality and long term energy resources of nuclear power while strengthening proliferation resistance. The workshop participants agreed on the following statements. The workshop considered a number of technologies to deal with spent nuclear fuels and current actinide inventories. The conclusion was reached that substantial increase in nuclear power production will require that the issue of spent nuclear fuel be resolved. The Workshop concluded that 14 MeV fusion neutrons can be used to destroy nuclear reactor by-products, some of which would otherwise have to be stored for geologic periods of time. The production of 14 MeV neutrons is based on existing fusion technologies at different research institutions in several countries around the world. At the present time this technology is used to produce 14 MeV neutrons in JET. More development work will be required, however, to bring fusion technology to the level where it can be used for actinide burning on an industrial scale. The workshop concluded that the potential

Japanese contributions to IAEA INTOR workshop, phase two A, part 2, chapter XI: concept evolution, chapter XII: design concept, and chapter XIII: operation and test programme

International Nuclear Information System (INIS)

Tomabechi, Ken; Fujisawa, Noboru; Iida, Hiromasa

1985-07-01

This report corresponds to Chapters XI, XII, and XIII of Japanese contribution report to IAEA INTOR Workship, Phase Two A, Part 2. In the phase Two A, Part 2 workshop, we have studied critical technical issues and have also assessed scientific and technical data bases. Based on those results, the INTOR design have been modified to upgrade the design concept. The major modification items are related to plasma beta value, plasma operation scenario, reactor size reduction, neutron fluence, tritium producing blanket, and implementation of active control coils. In those chapters, the concept evolution for the design modification and main results are described. (author)

Accelerators and storage rings. TS Workshop 2005. Book of Abstracts

International Nuclear Information System (INIS)

Ciriani, P.; Magnin, B.; Oliveira, R. de; Chevalley, J.; Artoos, K.; Bertone, C.; Minginette, P.; Corso, J.P.; Grillot, S.; Weisz, S.; Prodon, S.; Sakkinen, J.; Foraz, K.; Funken, A.; Bangert, N.; Hakulinen, T.; Boncompagni, Y.; Delamare, C.; Folch, R.; Poehler, M.; Bertarelli, A.; Martel, C.; Butin, F.; Osborne, J.; Evrard, S.; Lacarrere, D.; Gayde, J.C.; Renaglia, T.; Batz, M.; Tsesmelis, E.; Wijnands, T.; Perrot, A.L.; Gastal, M.; Atieh, S.; Cherif, A.; Costa Pinto, P.; Calatroni, S.; Ninin, P.; Battistin, M.; Arnau Izquierdo, G.; Favre, G.; Mathot, S.; Mainaud, H.; Podevin, C.; Jones, M.; Stowisek, J.; Roy, S.; Sanchez-Corral, E.; Petit, S.; Martel, P.; Colloca, C.; Van Der Bij, E.; Vadon, M.; Kahle, K.; Principe, R.; Macina, D.; Schmidt, R.; Ridewood, J.; Lopez-Hernandez, L.A.

2005-01-01

This document gathers the abstracts of the papers presented at the workshop. This workshop was dedicated to the status of the technical support of the LHC (large hadron collider) in CERN. The different issues concern: -) the installation of the equipment in the LHC tunnel (super-conducting magnets, cold boxes, PS magnets...), -) underground logistics, -) the installation of experimental areas, -) the new CERN control center, and -) special technologies. (A.C.)

Accelerators and storage rings. TS Workshop 2005. Book of Abstracts

Energy Technology Data Exchange (ETDEWEB)

Ciriani, P.; Magnin, B.; Oliveira, R. de; Chevalley, J.; Artoos, K.; Bertone, C.; Minginette, P.; Corso, J.P.; Grillot, S.; Weisz, S.; Prodon, S.; Sakkinen, J.; Foraz, K.; Funken, A.; Bangert, N.; Hakulinen, T.; Boncompagni, Y.; Delamare, C.; Folch, R.; Poehler, M.; Bertarelli, A.; Martel, C.; Butin, F.; Osborne, J.; Evrard, S.; Lacarrere, D.; Gayde, J.C.; Renaglia, T.; Batz, M.; Tsesmelis, E.; Wijnands, T.; Perrot, A.L.; Gastal, M.; Atieh, S.; Cherif, A.; Costa Pinto, P.; Calatroni, S.; Ninin, P.; Battistin, M.; Arnau Izquierdo, G.; Favre, G.; Mathot, S.; Mainaud, H.; Podevin, C.; Jones, M.; Stowisek, J.; Roy, S.; Sanchez-Corral, E.; Petit, S.; Martel, P.; Colloca, C.; Van Der Bij, E.; Vadon, M.; Kahle, K.; Principe, R.; Macina, D.; Schmidt, R.; Ridewood, J.; Lopez-Hernandez, L.A

2005-07-01

This document gathers the abstracts of the papers presented at the workshop. This workshop was dedicated to the status of the technical support of the LHC (large hadron collider) in CERN. The different issues concern: -) the installation of the equipment in the LHC tunnel (super-conducting magnets, cold boxes, PS magnets...), -) underground logistics, -) the installation of experimental areas, -) the new CERN control center, and -) special technologies. (A.C.)

H2@Scale Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Pivovar, Bryan

2017-03-31

Final report from the H2@Scale Workshop held November 16-17, 2016, at the National Renewable Energy Laboratory in Golden, Colorado. The U.S. Department of Energy's National Renewable Energy Laboratory hosted a technology workshop to identify the current barriers and research needs of the H2@Scale concept. H2@Scale is a concept regarding the potential for wide-scale impact of hydrogen produced from diverse domestic resources to enhance U.S. energy security and enable growth of innovative technologies and domestic industries. Feedback received from a diverse set of stakeholders at the workshop will guide the development of an H2@Scale roadmap for research, development, and early stage demonstration activities that can enable hydrogen as an energy carrier at a national scale.

Examining Science Teachers' Argumentation in a Teacher Workshop on Earthquake Engineering

Science.gov (United States)

Cavlazoglu, Baki; Stuessy, Carol

2018-02-01

The purpose of this study was to examine changes in the quality of science teachers' argumentation as a result of their engagement in a teacher workshop on earthquake engineering emphasizing distributed learning approaches, which included concept mapping, collaborative game playing, and group lesson planning. The participants were ten high school science teachers from US high schools who elected to attend the workshop. To begin and end the teacher workshop, teachers in small groups engaged in concept mapping exercises with other teachers. Researchers audio-recorded individual teachers' argumentative statements about the inclusion of earthquake engineering concepts in their concept maps, which were then analyzed to reveal the quality of teachers' argumentation. Toulmin's argumentation model formed the framework for designing a classification schema to analyze the quality of participants' argumentative statements. While the analysis of differences in pre- and post-workshop concept mapping exercises revealed that the number of argumentative statements did not change significantly, the quality of participants' argumentation did increase significantly. As these differences occurred concurrently with distributed learning approaches used throughout the workshop, these results provide evidence to support distributed learning approaches in professional development workshop activities to increase the quality of science teachers' argumentation. Additionally, these results support the use of concept mapping as a cognitive scaffold to organize participants' knowledge, facilitate the presentation of argumentation, and as a research tool for providing evidence of teachers' argumentation skills.

Obesity Prevention from Conception: A Workshop to Guide the Development of a Pan-Canadian Trial Targeting the Gestational Period

Directory of Open Access Journals (Sweden)

Kristi B. Adamo

2014-01-01

Full Text Available This report summarizes a meeting, Obesity Prevention from Conception , held in Ottawa in 2012. This planning workshop was funded by the Canadian Institutes of Health Research (CIHR to bring together researchers with expertise in the area of maternal obesity (OB and weight gain in pregnancy and pregnancy-related disease to attend a one-day workshop and symposium to discuss the development of a cross-Canada lifestyle intervention trial for targeting pregnant women. This future intervention will aim to reduce downstream OB in children through encouraging appropriate weight gain during the mother's pregnancy. The workshop served to (i inform the development of a lifestyle intervention for women with a high pre-pregnancy body mass index (BMI, (ii identify site investigators across Canada, and (iii guide the development of a grant proposal focusing on the health of mom and baby. A brief summary of the presentations as well as the focus groups is presented for use in planning future research.

History of the RSIC seminar-workshops

International Nuclear Information System (INIS)

Maskewitz, B.F.

1992-01-01

The RSIC concept of the open-quote seminar-workshop close-quote as a means to review the state-of-the-art of specific computing technology and to transmit a great deal of information to a large number of people in a short period of time evolved over a 30-year period. This paper presents the background leading to the development of the concept and details the history of the seminars and workshops organized by RSIC staff members through the years, 1965 - 1992

Proceedings of the workshop on applied mathematics

Energy Technology Data Exchange (ETDEWEB)

Lee, H C; Couture, M; Douglas, S; Leivo, H P

1992-10-01

The Workshop on Applied Mathematics was held at the Cockcroft Centre, Deep River, Ontario, 1992 February 7-8. The purpose of the workshop was to provide a forum for applied mathematicians to survey the use and to discuss the future of applied mathematics at AECL Research. There were 57 participants at the workshop A total of eight 30-minute and 25 15-minute talks were presented describing mathematical techniques used in the whole range of activities at AECL Research, from numerical simulation of fluid flow through eddy current testing to quantum algebra and accelerator physics.

Proceedings of the workshop on applied mathematics

International Nuclear Information System (INIS)

Lee, H.C.; Couture, M.; Douglas, S.; Leivo, H.P.

1992-10-01

The Workshop on Applied Mathematics was held at the Cockcroft Centre, Deep River, Ontario, 1992 February 7-8. The purpose of the workshop was to provide a forum for applied mathematicians to survey the use and to discuss the future of applied mathematics at AECL Research. There were 57 participants at the workshop A total of eight 30-minute and 25 15-minute talks were presented describing mathematical techniques used in the whole range of activities at AECL Research, from numerical simulation of fluid flow through eddy current testing to quantum algebra and accelerator physics

NATO and a Nuclear Iran - Concept Paper, Workshop Summary

International Nuclear Information System (INIS)

Tertrais, Bruno

2010-01-01

On October 7, 2010, The Foundation for Strategic Research (Fondation pour la Recherche Strategique) convened a day-long workshop in Paris to discuss the consequences for NATO of a nuclear-armed Iran, with support from the German Marshall Fund of the United States. The workshop involved around twenty experts from Alliance and non-Alliance countries, NATO officials, and French officials. This paper is a brief summary of the debate, focusing on the main ideas developed by the participants

It 'did what it said on the tin' - participant's views of the content and process of donor conception parenthood preparation workshops.

Science.gov (United States)

Crawshaw, Marilyn; Montuschi, Olivia

2014-03-01

Using donor conception treatment for family building brings challenges as well as rewards. As social model approaches to managing genetic difference within families gradually replace earlier medical models, parents are encouraged to be open with their children about their origins amidst greater social acceptance. Little is known about effective interventions to help prospective parents prepare for such family life. A survey was sent to participants in 16 Preparation for Parenthood workshops run in England by Donor Conception Network, a peer support organisation, between 2008 and 2010. The 79 respondents (32.4% response) included heterosexual couples, lesbian couples and single women considering sperm, egg or double donation. In 86% couples, both partners responded. The use of a range of techniques, a family lifespan approach, facilitators with personal as well as professional experience, medical and psychosocial specialists, and access to peer support were well received. Results suggest the value of attending cognitive and affective processes, acknowledging the impact of stigma and discussing how the donor's biography/presence can be conjoined with that of the new family. Findings suggest workshop approaches to donor conception parenthood preparation can be useful for prospective lesbian/single women/heterosexual-headed families considering donor conception. Such interventions have not previously been reported.

Beat-wave laser accelerators, further comment including note on the 'Surfatron' concept

International Nuclear Information System (INIS)

Lawson, J.D.

1984-07-01

The paper deals with the Rutherford Appleton Laboratory (RAL) study of the beat-wave particle accelerator, intended for high energy physics. Three factors; the build-up of beat-wave, the surfatron concept and the self-focusing effects are considered in the context of the RAL study. (U.K.)

Workshop: Keeping track of particle beams

International Nuclear Information System (INIS)

Anon.

1990-01-01

How to monitor the beam in a particle accelerator - to measure beam position, intensity, profile, transverse and longitudinal emittance, and losses - was the topic of the first US National Workshop on Accelerator Instrumentation, at Brookhaven in October. Sponsored by the US Department of Energy, the meeting drew more than a hundred physicists and engineers from other national labs and from industry

Workshop: Keeping track of particle beams

Energy Technology Data Exchange (ETDEWEB)

Anon.

1990-01-15

How to monitor the beam in a particle accelerator - to measure beam position, intensity, profile, transverse and longitudinal emittance, and losses - was the topic of the first US National Workshop on Accelerator Instrumentation, at Brookhaven in October. Sponsored by the US Department of Energy, the meeting drew more than a hundred physicists and engineers from other national labs and from industry.

Accelerator-driven sub-critical target concept for transmutation of nuclear wastes

International Nuclear Information System (INIS)

Van Tuyle, G.J.; Todosow, M.; Aronson, A.L.; Takahashi, H.; Geiger, M.J.

1991-01-01

A means of transmuting key long-lived nuclear wastes, primarily the minor actinides (Np, Am, Cm) and iodine, using a hybrid proton accelerator and sub-critical lattice, is proposed. By partitioning the components of the light water reactor (LWR) spent fuel and by transmuting key elements, such as the plutonium, the minor actinides, and a few of the long-lived fission products, some of the most significant challenges in building a waste repository can be substantially reduced. The proposed machine, based on the described PHOENIX Concept, would transmute the minor actinides and the iodine produced by 75 LWRs, and would generate usable electricity (beyond that required to run the large accelerator) of 850 MW e . 19 refs., 20 figs

TPC workshop summary

International Nuclear Information System (INIS)

Nygren, D.R.

1984-01-01

The Time Projection Chamber (TPC) concept is now nearly ten years old and, as is evident in this workshop, is still evolving in many directions. From the liquid xenon TPC for double beta decay studies to the impressively large second generation TPC for the LEP experiment ALEPH, the surprising diversity of current applications is apparent. This workshop, the first to concentrate solely on the TPC has provided a most congenial and rewarding occasion for all TPC enthusiasts to share experience, results, and ideas

Proceedings of the workshop on the PS-spin collider

International Nuclear Information System (INIS)

Mori, Yoshiharu

1993-05-01

This volume is a record of the PS-Spin Collider Workshop which was held at KEK, Jan. 31-Feb.1, 1992. As a future project of the KEK 12-GeV proton synchrotron (KEK-PS), the hadron collider (PS-Collider), has been under discussion. Originally, the PSC was designed for heavy ion beam collisions with the energy range of 5-7 GeV/u. If polarized protons are accelerated in PSC, 19 x 19 GeV collisions are possible. This workshop was proposed to bring together interested experimentalists and accelerator physicists to discuss the case that could be made for polarization physics and the technical feasibility at the PS Spin Collider. More than 30 physicists participated in the workshop and very interesting and useful discussions took place. (author)

New accelerator ideas

International Nuclear Information System (INIS)

Anon.

1985-01-01

In the past, providing higher particle beam energies meant building bigger accelerators. It is now universally accepted that with the current generation of accelerator projects either under construction (such as LEP at CERN) or proposed (such as the Superconducting Super Collider in the US), conventional techniques are reaching their practical limit. With the growing awareness that progress in particle physics requires new methods to accelerate particles, workshops and study groups are being set up across the world to search for ideas for the machines of tomorrow

New accelerator ideas

Energy Technology Data Exchange (ETDEWEB)

Anon.

1985-05-15

In the past, providing higher particle beam energies meant building bigger accelerators. It is now universally accepted that with the current generation of accelerator projects either under construction (such as LEP at CERN) or proposed (such as the Superconducting Super Collider in the US), conventional techniques are reaching their practical limit. With the growing awareness that progress in particle physics requires new methods to accelerate particles, workshops and study groups are being set up across the world to search for ideas for the machines of tomorrow.

Proceedings of the switched power workshop

International Nuclear Information System (INIS)

Fernow, R.C.

1988-01-01

These proceedings contain most of the presentations given at a workshop on the current state of research in techniques for switched power acceleration. The proceedings are divided, as was the workshop itself, into two parts. Part 1, contains the latest results from a number of groups active in switched power research. The major topic here is a method for switching externally supplied power onto a transmission line. Advocates for vacuum photodiode switching, solid state switching, gas switching, and synthetic pulse generation are all presented. Other important areas of research described in this section concern: external electrical and laser pulsing systems; the properties of the created electromagnetic pulse; structures used for transporting the electromagnetic pulse to the region where the electron beam is located; and possible applications. Part 2 of the proceedings considers the problem of designing a high brightness electron gun using switched power as the power source. This is an important first step in demonstrating the usefulness of switched power techniques for accelerator physics. In addition such a gun could have immediate practical importance for advanced acceleration studies since the brightness could exceed that of present sources by several orders of magnitude. I would like to take this opportunity to thank Kathleen Tuohy and Patricia Tuttle for their assistance in organizing and running the workshop. Their tireless efforts contribute greatly to a very productive meeting

Network workshop

DEFF Research Database (Denmark)

Bruun, Jesper; Evans, Robert Harry

2014-01-01

This paper describes the background for, realisation of and author reflections on a network workshop held at ESERA2013. As a new research area in science education, networks offer a unique opportunity to visualise and find patterns and relationships in complicated social or academic network data....... These include student relations and interactions and epistemic and linguistic networks of words, concepts and actions. Network methodology has already found use in science education research. However, while networks hold the potential for new insights, they have not yet found wide use in the science education...... research community. With this workshop, participants were offered a way into network science based on authentic educational research data. The workshop was constructed as an inquiry lesson with emphasis on user autonomy. Learning activities had participants choose to work with one of two cases of networks...

t4 Workshop Report*

Science.gov (United States)

Kleensang, Andre; Maertens, Alexandra; Rosenberg, Michael; Fitzpatrick, Suzanne; Lamb, Justin; Auerbach, Scott; Brennan, Richard; Crofton, Kevin M.; Gordon, Ben; Fornace, Albert J.; Gaido, Kevin; Gerhold, David; Haw, Robin; Henney, Adriano; Ma’ayan, Avi; McBride, Mary; Monti, Stefano; Ochs, Michael F.; Pandey, Akhilesh; Sharan, Roded; Stierum, Rob; Tugendreich, Stuart; Willett, Catherine; Wittwehr, Clemens; Xia, Jianguo; Patton, Geoffrey W.; Arvidson, Kirk; Bouhifd, Mounir; Hogberg, Helena T.; Luechtefeld, Thomas; Smirnova, Lena; Zhao, Liang; Adeleye, Yeyejide; Kanehisa, Minoru; Carmichael, Paul; Andersen, Melvin E.; Hartung, Thomas

2014-01-01

Summary Despite wide-spread consensus on the need to transform toxicology and risk assessment in order to keep pace with technological and computational changes that have revolutionized the life sciences, there remains much work to be done to achieve the vision of toxicology based on a mechanistic foundation. A workshop was organized to explore one key aspect of this transformation – the development of Pathways of Toxicity (PoT) as a key tool for hazard identification based on systems biology. Several issues were discussed in depth in the workshop: The first was the challenge of formally defining the concept of a PoT as distinct from, but complementary to, other toxicological pathway concepts such as mode of action (MoA). The workshop came up with a preliminary definition of PoT as “A molecular definition of cellular processes shown to mediate adverse outcomes of toxicants”. It is further recognized that normal physiological pathways exist that maintain homeostasis and these, sufficiently perturbed, can become PoT. Second, the workshop sought to define the adequate public and commercial resources for PoT information, including data, visualization, analyses, tools, and use-cases, as well as the kinds of efforts that will be necessary to enable the creation of such a resource. Third, the workshop explored ways in which systems biology approaches could inform pathway annotation, and which resources are needed and available that can provide relevant PoT information to the diverse user communities. PMID:24127042

Concepts for the magnetic design of the MITICA neutral beam test facility ion accelerator.

Science.gov (United States)

Chitarin, G; Agostinetti, P; Marconato, N; Marcuzzi, D; Sartori, E; Serianni, G; Sonato, P

2012-02-01

The megavolt ITER injector concept advancement neutral injector test facility will be constituted by a RF-driven negative ion source and by an electrostatic Accelerator, designed to produce a negative Ion with a specific energy up to 1 MeV. The beam is then neutralized in order to obtain a focused 17 MW neutral beam. The magnetic configuration inside the accelerator is of crucial importance for the achievement of a good beam efficiency, with the early deflection of the co-extracted and stripped electrons, and also of the required beam optic quality, with the correction of undesired ion beamlet deflections. Several alternative magnetic design concepts have been considered, comparing in detail the magnetic and beam optics simulation results, evidencing the advantages and drawbacks of each solution both from the physics and engineering point of view.

Physics beyond Colliders Kickoff Workshop

CERN Document Server

2016-01-01

The aim of the workshop is to explore the opportunities offered by the CERN accelerator complex and infrastructure to get new insights into some of today's outstanding questions in particle physics through projects complementary to high-energy colliders and other initiatives in the world. The focus is on fundamental physics questions that are similar in spirit to those addressed by high-energy colliders, but that may require different types of experiments. The kickoff workshop is intended to stimulate new ideas for such projects, for which we encourage the submission of abstracts.

Workshop on Physics Beyond Colliders

CERN Document Server

2016-01-01

The aim of the workshop is to explore the opportunities offered by the CERN accelerator complex and infrastructure to get new insights into some of today's outstanding questions in particle physics through projects complementary to high-energy colliders and other initiatives in the world. The focus is on fundamental physics questions that are similar in spirit to those addressed by high-energy colliders, but that may require different types of experiments. The kick-off workshop is intended to stimulate new ideas for such projects, for which we encourage the submission of abstracts.

Sixth international workshop on linear colliders. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Urakawa, Junji [ed.

1995-08-01

The sixth international workshop on linear colliders (LC95) was held by KEK at Tsukuba Center for Institute. In the workshop 8 parallel working group were organized: WG1 (beam sources and injection linacs), WG2 (damping rings and bunch compressors), WG3 (a: RF sources and structures, b: superconducting cavities, c: two beam accelerators), WG4 (beam dynamics in main linacs), WG5 (final focus and integration regions), WG6 (beam instrumentation), WG7 (overall parameters and construction techniques), WG8 (gamma-gamma collider and miscellaneous). This issue compiles materials which were used in the workshop. (J.P.N.).

Sixth international workshop on linear colliders. Proceedings

International Nuclear Information System (INIS)

Urakawa, Junji

1995-08-01

The sixth international workshop on linear colliders (LC95) was held by KEK at Tsukuba Center for Institute. In the workshop 8 parallel working group were organized: WG1 (beam sources and injection linacs), WG2 (damping rings and bunch compressors), WG3 (a: RF sources and structures, b: superconducting cavities, c: two beam accelerators), WG4 (beam dynamics in main linacs), WG5 (final focus and integration regions), WG6 (beam instrumentation), WG7 (overall parameters and construction techniques), WG8 (gamma-gamma collider and miscellaneous). This issue compiles materials which were used in the workshop. (J.P.N.)

Workshop on performance optimization of synchrotron radiation storage rings

International Nuclear Information System (INIS)

Decker, G.

1995-01-01

The purpose of this workshop was to provide a forum, with user participation, for accelerator physicists the synchrotron light source field to discuss current and planned state-of-the-art techniques storage ring performance. The scope of the workshop focused on two areas: lattice characterization and measurement, and fundamental limitations on low frequency beam stability

Advanced Wind Turbine Drivetrain Concepts. Workshop Report

Energy Technology Data Exchange (ETDEWEB)

none,

2010-12-01

This report presents key findings from the Department of Energy’s Advanced Drivetrain Workshop, held on June 29-30, 2010, to assess different advanced drivetrain technologies, their relative potential to improve the state-of-the-art in wind turbine drivetrains, and the scope of research and development needed for their commercialization in wind turbine applications.

Some nuclear safety aspects of the Los Alamos accelerator based converion concept

Energy Technology Data Exchange (ETDEWEB)

Gudowski, W.; Moeller, E. [Royal Institute of Technology, Stockholm (Sweden); Venneri, F. [Los Alamos National Laboratory, NM (United States)

1995-10-01

The detailed analysis of the few parameters important for the safety of the accelerator-driven plutonium burner concept developed at Los Alamos National Laboratory was performed. The plutonium load, optimal thermalization of the neutron spectrum and temperature reactivity coefficients were investigated. The calculations revealed the strong positive temperature reactivity coeffecient. The ways to solve this problem are suggested.

A Los Alamos concept for accelerator transmutation of waste and energy production (ATW)

International Nuclear Information System (INIS)

1990-01-01

This document contains the diagrams presented at the ATW (Accelerator Transmutation of Waste and Energy Production) External Review, December 10-12, 1990, held at Los Alamos National Laboratory. Included are the charge to the committee and the presentations for the committee's review. Topics of the presentations included an overview of the concept, LINAC technology, near-term application -- high-level defense wastes (intense thermal neutron source, chemistry and materials), advanced application of the ATW concept -- fission energy without a high-level waste stream (overview, advanced technology, and advanced chemistry), and a summary of the research issues

A Concept for Directly Coupled Pulsed Electromagnetic Acceleration of Plasmas

Science.gov (United States)

Thio, Y.C. Francis; Cassibry, Jason T.; Eskridge, Richard; Smith, James; Wu, S. T.; Rodgers, Stephen L. (Technical Monitor)

2001-01-01

Plasma jets with high momentum flux density are required for a variety of applications in propulsion research. Methods of producing these plasma jets are being investigated at NASA Marshall Space Flight Center. The experimental goal in the immediate future is to develop plasma accelerators which are capable of producing plasma jets with momentum flux density represented by velocities up to 200 km/s and ion density up to 10(exp 24) per cu m, with sufficient precision and reproducibility in their properties, and with sufficiently high efficiency. The jets must be sufficiently focused to allow them to be transported over several meters. A plasma accelerator concept is presented that might be able to meet these requirements. It is a self-switching, shaped coaxial pulsed plasma thruster, with focusing of the plasma flow by shaping muzzle current distribution as in plasma focus devices, and by mechanical tapering of the gun walls. Some 2-D MHD modeling in support of the conceptual design will be presented.

IEC 61850 and IEC 62351 Cyber Security Acceleration Workshop

Energy Technology Data Exchange (ETDEWEB)

Clements, Samuel L.; Edgar, Thomas W.; Manz, David O.

2012-04-01

The purpose of this workshop was to identify and discuss concerns with the use and adoption of IEC 62351 security standard for IEC 61850 compliant control system products. The industry participants discussed performance, interoperability, adoption, challenges, business cases, and future issues.

Marine and Hydrokinetic Technology (MHK) Instrumentation, Measurement, and Computer Modeling Workshop

Energy Technology Data Exchange (ETDEWEB)

Musial, W.; Lawson, M.; Rooney, S.

2013-02-01

The Marine and Hydrokinetic Technology (MHK) Instrumentation, Measurement, and Computer Modeling Workshop was hosted by the National Renewable Energy Laboratory (NREL) in Broomfield, Colorado, July 9-10, 2012. The workshop brought together over 60 experts in marine energy technologies to disseminate technical information to the marine energy community and collect information to help identify ways in which the development of a commercially viable marine energy industry can be accelerated. The workshop was comprised of plenary sessions that reviewed the state of the marine energy industry and technical sessions that covered specific topics of relevance. Each session consisted of presentations, followed by facilitated discussions. During the facilitated discussions, the session chairs posed several prepared questions to the presenters and audience to encourage communication and the exchange of ideas between technical experts. Following the workshop, attendees were asked to provide written feedback on their takeaways and their best ideas on how to accelerate the pace of marine energy technology development. The first four sections of this document give a general overview of the workshop format, provide presentation abstracts and discussion session notes, and list responses to the post-workshop questions. The final section presents key findings and conclusions from the workshop that suggest how the U.S. Department of Energy and national laboratory resources can be utilized to most effectively assist the marine energy industry.

Marine and Hydrokinetic Technology (MHK) Instrumentation, Measurement, and Computer Modeling Workshop

Energy Technology Data Exchange (ETDEWEB)

Musial, W. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lawson, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Rooney, S. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-02-01

The Marine and Hydrokinetic Technology (MHK) Instrumentation, Measurement, and Computer Modeling Workshop was hosted by the National Renewable Energy Laboratory (NREL) in Broomfield, Colorado, July 9–10, 2012. The workshop brought together over 60 experts in marine energy technologies to disseminate technical information to the marine energy community, and to collect information to help identify ways in which the development of a commercially viable marine energy industry can be accelerated. The workshop was comprised of plenary sessions that reviewed the state of the marine energy industry and technical sessions that covered specific topics of relevance. Each session consisted of presentations, followed by facilitated discussions. During the facilitated discussions, the session chairs posed several prepared questions to the presenters and audience to encourage communication and the exchange of ideas between technical experts. Following the workshop, attendees were asked to provide written feedback on their takeaways from the workshop and their best ideas on how to accelerate the pace of marine energy technology development. The first four sections of this document give a general overview of the workshop format, provide presentation abstracts, supply discussion session notes, and list responses to the post-workshop questions. The final section presents key findings and conclusions from the workshop that suggest what the most pressing MHK technology needs are and how the U.S. Department of Energy (DOE) and national laboratory resources can be utilized to assist the marine energy industry in the most effective manner.

Proceedings of the workshop on ion source issues relevant to a pulsed spallation neutron source: Part 1: Workshop summary

International Nuclear Information System (INIS)

Schroeder, L.; Leung, K.N.; Alonso, J.

1994-10-01

The workshop reviewed the ion-source requirements for high-power accelerator-driven spallation neutron facilities, and the performance of existing ion sources. Proposals for new facilities in the 1- to 5-MW range call for a widely differing set of ion-source requirements. For example, the source peak current requirements vary from 40 mA to 150 mA, while the duty factor ranges from 1% to 9%. Much of the workshop discussion centered on the state-of-the-art of negative hydrogen ion source (H - ) technology and the present experience with Penning and volume sources. In addition, other ion source technologies, for positive ions or CW applications were reviewed. Some of these sources have been operational at existing accelerator complexes and some are in the source-development stage on test stands

EIC Electron Beam Polarimetry Workshop Summary

International Nuclear Information System (INIS)

Lorenzon, W.

2008-01-01

A summary of the Precision Electron Beam Polarimetry Workshop for a future Electron Ion Collider (EIC) is presented. The workshop was hosted by the University of Michigan Physics Department in Ann Arbor on August 23-24, 2007 with the goal to explore and study the electron beam polarimetry issues associated with the EIC to achieve sub-1% precision in polarization determination. Ideas are being presented that were exchanged among experts in electron polarimetry and source and accelerator design to examine existing and novel electron beam polarization measurement schemes

New developments in particle acceleration techniques. Proceedings. Vol. 2

International Nuclear Information System (INIS)

Turner, S.

1987-01-01

A Workshop organised jointly by the European Committee for Future Accelerators (ECFA), the CERN Accelerator School (CAS), the Institut National de Physique Nucleaire et de Physique des Particules (IN2P3), the Institut pour la Recherche Fondamentale/Commissariat a l'Energie Atomique (IRF/CEA) and the European Physical Society (EPS) was held at the Laboratoire de l'Accelerateur Lineaire (LAL), Orsay, from 29 June to 4 July 1987. Its purpose was to review current experimental and theoretical developments in charged-particle accelerator techniques and to address problems related to future very-high-energy machines. These proceedings contain the great majority of the papers presented at the Workshop, the corresponding questions and answers, and the round-table discussion. The principal topics were semi-conventional high-frequency linacs, transformer acceleration mechanisms, acceleration using plasma, e + e - sources, including low-emittance production and preservation, final focus and interaction point, and other new ideas. Among the latter were open accelerating structures, crystal X-ray accelerators, ferroelectrics, and acceleration using lasers. (orig.)

New developments in particle acceleration techniques. Proceedings. Vol. 1

International Nuclear Information System (INIS)

Turner, S.

1987-01-01

A Workshop organised jointly by the European Committee for Future Accelerators (ECFA), the CERN Accelerator School (CAS), the Institut National de Physique Nucleaire et de Physique des Particules (IN2P3), the Institut pour la Recherche Fondamentale/Commissariat a l'Energie Atomique (IRF/CEA) and the European Physical Society (EPS) was held at the Laboratoire de l'Accelerateur Lineaire (LAL), Orsay, from 29 June to 4 July 1987. Its purpose was to review current experimental and theoretical developments in charged-particle accelerator techniques and to address problems related to future very-high-energy machines. These proceedings contain the great majority of the papers presented at the Workshop, the corresponding questions and answers, and the round-table discussion. The principal topics were semi-conventional high-frequency linacs, transformer acceleration mechanisms, acceleration using plasma, e + e - sources including low-emittance production and preservation, final focus and interaction point, and other new ideas. Among the latter were open accelerating structures, crystal X-ray accelerators, ferroelectrics, and acceleration using lasers. (orig.)

Proceedings of the workshop on atomic physics with fast heavy-ion beams

International Nuclear Information System (INIS)

Kanter, E.P.; Minchinton, A.

1983-01-01

The Workshop on Atomic Physics with Fast Heavy-Ion Beams was held in the Physics Division, Argonne National Laboratory on January 20 and 21, 1983. The meeting brought together approx. 50 practitioners in the field of accelerator-based atomic physics. The workshop was held to focus attention on possible areas of atomic physics research which would benefit from use of the newest generation of accelerators designed to produce intense high-quality beams of fast heavy ions. Abstracts of individual paper were prepared separately for the data base

Accelerator driven systems for energy production and waste incineration: Physics, design and related nuclear data

International Nuclear Information System (INIS)

Herman, M.; Stanculescu, A.; Paver, N.

2003-01-01

This volume contains the notes of lectures given at the workshops 'Hybrid Nuclear Systems for Energy Production, Utilisation of Actinides and Transmutation of Long-lived Radioactive Waste' and 'Nuclear Data for Science and Technology: Accelerator Driven Waste Incineration', held at the Abdus Salam ICTP in September 2001. The subject of the first workshop was focused on the so-called Accelerator Driven Systems, and covered the most important physics and technological aspects of this innovative field. The second workshop was devoted to an exhaustive survey on the acquisition, evaluation, retrieval and validation of the nuclear data relevant to the design of Accelerator Driven Systems

Accelerator driven systems for energy production and waste incineration: Physics, design and related nuclear data

Energy Technology Data Exchange (ETDEWEB)

Herman, M; Stanculescu, A [International Atomic Energy Agency, Vienna (Austria); Paver, N [University of Trieste and INFN, Trieste (Italy)

2003-06-15

This volume contains the notes of lectures given at the workshops 'Hybrid Nuclear Systems for Energy Production, Utilisation of Actinides and Transmutation of Long-lived Radioactive Waste' and 'Nuclear Data for Science and Technology: Accelerator Driven Waste Incineration', held at the Abdus Salam ICTP in September 2001. The subject of the first workshop was focused on the so-called Accelerator Driven Systems, and covered the most important physics and technological aspects of this innovative field. The second workshop was devoted to an exhaustive survey on the acquisition, evaluation, retrieval and validation of the nuclear data relevant to the design of Accelerator Driven Systems.

1995 second modulator-klystron workshop: A modulator-klystron workshop for future linear colliders

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This second workshop examined the present state of modulator design and attempted an extrapolation for future electron-positron linear colliders. These colliders are currently viewed as multikilometer-long accelerators consisting of a thousand or more RF sources with 500 to 1,000, or more, pulsed power systems. The workshop opened with two introductory talks that presented the current approaches to designing these linear colliders, the anticipated RF sources, and the design constraints for pulse power. The cost of main AC power is a major economic consideration for a future collider, consequently the workshop investigated efficient modulator designs. Techniques that effectively apply the art of power conversion, from the AC mains to the RF output, and specifically, designs that generate output pulses with very fast rise times as compared to the flattop. There were six sessions that involved one or more presentations based on problems specific to the design and production of thousands of modulator-klystron stations, followed by discussion and debate on the material.

Report of workshop on energy

International Nuclear Information System (INIS)

Tsujimoto, Kazufumi; Nagai, Yasuki

2005-03-01

The Working Group on Energy (WG) was organized under International Union of Pure and Applied Physics (IUPAP). The WG has been considering problems on future energy supply and role of physics to solve the subjects. As one of activities of the WG, a Workshop on Energy was held on May 13, 2004 at Center for Promotion of Computational Science and Engineering, Japan Atomic Energy Research Institute (JAERI) in Tokyo hosted by IUPAP and co-hosted by JAERI and High Energy Accelerator Research Organization. The objectives of this workshop are to suggest active contributions of pure and applied physics field to the solution of the energy problem and to advance research and development (R and D) of future energy through the discussions about present status, problem and prospect of different energy development in the world and in Japan. This report records the summary of the Workshop and, abstracts and materials of 12 presentations. After the invited presentations about overview of energy problems in the world, in China and in Japan, R and D activities on the following four fields were presented; 'Research and Development of New Energy', 'Research and Development of Fusion', 'Prospect of Accelerator Driven System (ADS)', and 'Hydrogen Production, Storage and Transportation'. At the end of the workshop, possible role of physics for the current and future energy problem was discussed. It was recognized that the energy problem was not as simple as to be solved by one country, and hence the international collaboration became essential. The importance of the coordination with other fields, such as chemistry and material, was also emphasized. (author)

LHeC Workshop | 24-26 June 2015 | CERN and Chavannes-de-Bogis

CERN Multimedia

2015-01-01

The next LHeC workshop will be taking place from 24-26 June, 2015. The workshop will open with a special colloquium at CERN on Wednesday, 24 June.    Note that the special, opening colloquium will be held on Wednesday, 24 June from 3 p.m. in the CERN Main Auditorium. Here is the programme of this special event: Herwig SCHOPPER Welcome 15:00 - 15:10 Sergio BERTOLUCCI The Development of the LHeC 15:10 - 15:30 Oliver BRUENING Accelerator Design 15:30 - 15:50 Erk JENSEN Concept of a High Intensity Energy Recovery Linac Facility 15:50 - 16:10 Coffee break 16:10 - 16:30 Monica D'ONOFRIO ep/A Physics at the Energy Frontier 16:30 - 17:00 Andrea GADDI Detectors for the LHeC and FCC-he 17:00 - 17:20 Guido ALTARELLI Importance of Deep Inelastic Scattering in the 21st century 17:20 - 17:40 Note that this special colloquium will be also webcast: https://webcast.web.cern.ch/webcast/  For more information, visit the Indico page of the event: https://indico.cer...

Telemedicine in Space Flight - Summary of a NASA Workshop

Science.gov (United States)

Barsten, K. N.; Watkins, S. D.; Otto, C.; Baumann, D. K.

2011-01-01

The Exploration Medical Capability Element of the Human Research Program at NASA Johnson Space Center hosted the Telemedicine Workshop in January 2011 to discuss the medical operational concept for a crewed mission to a near-Earth asteroid (NEA) and to identify areas for future work and collaboration. With the increased likelihood of a medical incident on a long duration exploration mission to a near-Earth asteroid, as well as the fact that there will likely be limited medical capabilities and resources available to diagnose and treat medical conditions, it is anticipated that a more structured use of telemedicine will become highly desirable. The workshop was convened to solicit expert opinion on current telemedicine practices and on medical care in remote environments. Workshop Objectives: The workshop brought together leaders in telemedicine and remote medicine from The University of Texas Medical Branch, Henry Ford Hospital, Ontario Telemedicine Network, U.S. Army Institute of Surgical Research, University of Miami, American Telemedicine Association, Doctors Without Borders, and the Pan American Health Organization. The primary objectives of the workshop were to document the medical operations concept for a crewed mission to a NEA, to determine gaps between current capabilities and the capabilities outlined in the operations concept, to identify research required to close these gaps, and to discuss potential collaborations with external-to-NASA organizations with similar challenges. Summary of Discussions and Conclusions: The discussions held during the workshop and the conclusions reached by the workshop participants were grouped into seven categories: Crew Medical Officers, Patient Area in Spacecraft, Training, Electronic Medical Records, Intelligent Care Systems, Consultation Protocols, Prophylactic Surgical Procedures, and Data Prioritization. The key points discussed under each category will be presented.

Physics of high energy particle accelerators. AIP conference proceedings No. 127

International Nuclear Information System (INIS)

Month, M.; Dahl, P.F.; Dienes, M.

1985-01-01

Topics covered in this workshop include accelerator physics, particle physics, and new acceleration methods. Eighteen lectures were presented. Individual abstracts were prepared separately for the data base

Proceedings of the workshop on polarized targets in storage rings

International Nuclear Information System (INIS)

Holt, R.J.

1984-08-01

Polarization phenomena have played an increasingly important part in the study of nuclei and nucleons in recent years. Polarization studies have been hampered by the relatively few and rather fragile polarized targets which are presently available. The concept of polarized gas targets in storage rings opens a much wider range of possibilities than is available in the external target geometry. This novel method will represent a considerable advance in nuclear physics and will continue to receive much attention in plans for future facilities. An internal, polarized-target station is being planned for the cooler ring at the Indiana University Cyclotron Facility. Internal targets are compatible with recent designs of electron accelerators proposed by the Massachusetts Institute of Technology and the Southeastern Universities Research Association. The key to nuclear-science programs based on internal targets pivots on recent developments in polarized atomic beam methods, which include the more recent laser-driven polarized targets. The workshop drew together a unique group of physicists in the fields of high-energy, nuclear and atomic physics. The meeting was organized in a manner that stimulated discussion among the 58 participants and focused on developments in polarized target technology and the underlying atomic physics. An impressive array of future possibilities for polarized targets as well as current developments in polarized target technology were discussed at the workshop. Abstracts of individual items from the workshop were prepared separately for the data base

Modeling and Simulation for Safeguards and Nonproliferation Workshop

Energy Technology Data Exchange (ETDEWEB)

Gilligan, Kimberly V. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kirk, Bernadette Lugue [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-01-01

The Modeling and Simulation for Safeguards and Nonproliferation Workshop was held December 15–18, 2014, at Oak Ridge National Laboratory. This workshop was made possible by the Next Generation Safeguards Initiative Human Capital Development (NGSI HCD) Program. The idea of the workshop was to move beyond the tried-and-true boot camp training of nonproliferation concepts to spend several days on the unique perspective of applying modeling and simulation (M&S) solutions to safeguards challenges.

Optical Network Testbeds Workshop

Energy Technology Data Exchange (ETDEWEB)

Joe Mambretti

2007-06-01

technologies. Several years ago, when many of these optical networking research topics were first being investigated, they were the subject of controversial debate. The new techniques challenged many long-held concepts related to architecture and technology. However, today all major networking organizations are transitioning toward infrastructure that incorporates these new concepts. This progress has been assisted through the series of Optical Networking Testbed Workshops (ONT). The first (ONT1) outlined a general framework of key issues and topics and developed a series of recommendations (www.nren.nasa.gov/workshop7). The second (ONT2) developed a common vision of optical network technologies, services, infrastructure, and organizations (www.nren.nasa.gov/workshop8). Processes that allow for a common vision encourage widespread deployment of these types of resources among advanced networking communities. Also, such a shared vision enables key concepts and technologies to migrate from basic research testbeds to wider networking communities. The ONT-3 workshop built on these earlier activities by expanding discussion to include additional considerations of the international interoperability and of greater impact of optical networking technology on networking in general. In accordance with this recognition, the workshop confirmed that future-oriented research and development is indispensable to fundamentally change the current Internet architecture to create a global network incorporating completely new concepts. The workshop also recognized that the first priority to allow for this progress is basic research and development, including international collaborative activities, which are important for the global realization of interoperability of a new generation architecture.

Dynamic defense workshop :

Energy Technology Data Exchange (ETDEWEB)

Crosby, Sean Michael; Doak, Justin E.; Haas, Jason Juedes.; Helinski, Ryan; Lamb, Christopher C.

2013-02-01

On September 5th and 6th, 2012, the Dynamic Defense Workshop: From Research to Practice brought together researchers from academia, industry, and Sandia with the goals of increasing collaboration between Sandia National Laboratories and external organizations, de ning and un- derstanding dynamic, or moving target, defense concepts and directions, and gaining a greater understanding of the state of the art for dynamic defense. Through the workshop, we broadened and re ned our de nition and understanding, identi ed new approaches to inherent challenges, and de ned principles of dynamic defense. Half of the workshop was devoted to presentations of current state-of-the-art work. Presentation topics included areas such as the failure of current defenses, threats, techniques, goals of dynamic defense, theory, foundations of dynamic defense, future directions and open research questions related to dynamic defense. The remainder of the workshop was discussion, which was broken down into sessions on de ning challenges, applications to host or mobile environments, applications to enterprise network environments, exploring research and operational taxonomies, and determining how to apply scienti c rigor to and investigating the eld of dynamic defense.

Using Patterns for Multivariate Monitoring and Feedback Control of Linear Accelerator Performance: Proof-of-Concept Research

International Nuclear Information System (INIS)

Cordes, Gail Adele; Van Ausdeln, Leo Anthony; Velasquez, Maria Elena

2002-01-01

The report discusses preliminary proof-of-concept research for using the Advanced Data Validation and Verification System (ADVVS), a new INEEL software package, to add validation and verification and multivariate feedback control to the operation of non-destructive analysis (NDA) equipment. The software is based on human cognition, the recognition of patterns and changes in patterns in time-related data. The first project applied ADVVS to monitor operations of a selectable energy linear electron accelerator, and showed how the software recognizes in real time any deviations from the optimal tune of the machine. The second project extended the software method to provide model-based multivariate feedback control for the same linear electron accelerator. The projects successfully demonstrated proof-of-concept for the applications and focused attention on the common application of intelligent information processing techniques

Nuclear thermal propulsion workshop overview

International Nuclear Information System (INIS)

Clark, J.S.

1991-01-01

NASA is planning an Exploration Technology Program as part of the Space Exploration Initiative to return U.S. astronauts to the moon, conduct intensive robotic exploration of the moon and Mars, and to conduct a piloted mission to Mars by 2019. Nuclear Propulsion is one of the key technology thrust for the human mission to Mars. The workshop addresses NTP (Nuclear Thermal Rocket) technologies with purpose to: assess the state-of-the-art of nuclear propulsion concepts; assess the potential benefits of the concepts for the mission to Mars; identify critical, enabling technologies; lay-out (first order) technology development plans including facility requirements; and estimate the cost of developing these technologies to flight-ready status. The output from the workshop will serve as a data base for nuclear propulsion project planning

8. stellarator workshop

International Nuclear Information System (INIS)

1991-07-01

The technical reports in this collection of papers were presented at the 8th International Workshop on Stellarators, and International Atomic Energy Agency Technical Committee Meeting. They include presentations on transport, magnetic configurations, fluctuations, equilibrium, stability, edge plasma and wall aspects, heating, diagnostics, new concepts and reactor studies. Refs, figs and tabs

Development of a new concept automatic frequency controller for an ultrasmall C-band linear accelerator guide

International Nuclear Information System (INIS)

Kamino, Yuichiro; Tsukuda, Kazuhiro; Kokubo, Masaki; Miura, Sadao; Hirai, Etsuro; Hiraoka, Masahiro; Ishikawa, Junzo

2007-01-01

We are developing a four-dimensional, image-guided radiotherapy system with a gimbaled x-ray head. The system has pursuing irradiation capability in addition to precise irradiation capability, owing to its agile x-ray head. The moving x-ray head requires a very small C-band accelerator guide. The heat intensity of the accelerator guide is much higher than that of conventional S-band medical linear accelerators. The resonance frequency varies over almost 1.0 MHz with a thermal time constant of about 30 s. An automatic frequency controller (AFC) is employed to compensate for this variation in resonance frequency. Furthermore, we noted that fast AFC response is important for step-and-shoot intensity modulation radiotherapy (IMRT), in which the beam is turned on and off frequently. Therefore, we invented a digital AFC, based on a new concept, to provide effective compensation for the thermal characteristics of the accelerator guide and to ensure stable and optimized x-ray treatment. An important aspect of the performance of the AFC is the capture-frequency range over which the AFC can seek, lock on to, and track the resonance frequency. The conventional, analog AFC used in S-band medical linear accelerators would have a capture-frequency range of about 0.9 MHz, if applied to our accelerator guide, and would be inappropriate. Conversely, our new AFC has a capture-frequency range of 24 MHz, which is well suited to our accelerator guide. The design concept behind this new AFC has been developed and verified. A full prototype system was constructed and tested on an existing accelerator guide at the rated x-ray output (500 cGy/min) of our radiotherapy system, with a pulse-repetition frequency of 300 Hz. The AFC acquired the resonance frequency of the accelerator guide within 0.15 s after beam-on, and provided stable tracking and adjustment of the frequency of the microwave source to the resonance frequency of the accelerator guide. With a planned improvement of the

Proceedings of the tau-charm factory workshop

International Nuclear Information System (INIS)

Beers, L.V.

1989-06-01

This report contains papers on the following main topics: machine physics; tau physics; D and D s physics; J/Ψ and charmonium physics; tau charm factories; workshop summary; accelerator physics; tau physics; charmed meson physics; J/Ψ and charmonium physics; and detector

Building the Concept of Acceleration - A Proposal for Promoting the Meaningful Learning

Directory of Open Access Journals (Sweden)

José Ricardo Ledur

2014-12-01

Full Text Available This work aims to present a sequence of activities to help the students concept of acceleration. It was developed with a group of eighth grade elementary school sutdents in a state school of Bom Princípio, RS. The physical quantities of kinematics are presents on the day-a-day but in classroom is perceived that students, in general, have difficulties in developing and understanding of concepts related to that topic. Previous experiences that the student experiences in their daily lives led him to build their own conceptions to explain the phenomena observed, and in school, are faced with the scientifically accepted concepts. These preconceptions are strongly rooted in the cognitive structure of the learner, are not easily replaced and added to the lack of contextualization of content taught, unattractive learning resources and teaching that emphasizes rote learning are factors that contribute to failure of learning. The activities are based on the principles of meaningful learning and focused on active student participation. A pre test for identifying knowledge and preconceptions was applied as well as the post-test assessment of knowledge building. Figures with strobe photographs and video were used as prerequisites for the development of the new concept organizers. Later, the students elaborated and executed projects using resources of shooting and sequential shots to apply the concepts involved in this study. The results observed during the didatical sequence indicate that the occurrence of learning of the concepts of kinematics.

Workshop on electroweak symmetry breaking: proceedings

International Nuclear Information System (INIS)

Hinchliffe, I.

1984-10-01

A theoretical workshop on electroweak symmetry breaking at the Superconducting Supercollider was held at Lawrence Berkeley Laboratory, June 4-22, 1984. The purpose of the workshop was to focus theoretical attention on the ways in which experimentation at the SSC could reveal manifestations of the phenomenon responsible for electroweak symmetry breaking. This issue represents, at present, the most compelling scientific argument for the need to explore the energy region to be made accessible by the SSC, and a major aim of the workshop was to involve a broad cross section of particle theorists in the ongoing process of sharpening the requirements for both accelerator and detector design that will ensure detection and identification of meaningful signals, whatever form the electroweak symmetry breaking phenomenon should actually take. Separate entries were prepared for the data base for the papers presented

Workshop on electroweak symmetry breaking: proceedings

Energy Technology Data Exchange (ETDEWEB)

Hinchliffe, I. (ed.)

1984-10-01

A theoretical workshop on electroweak symmetry breaking at the Superconducting Supercollider was held at Lawrence Berkeley Laboratory, June 4-22, 1984. The purpose of the workshop was to focus theoretical attention on the ways in which experimentation at the SSC could reveal manifestations of the phenomenon responsible for electroweak symmetry breaking. This issue represents, at present, the most compelling scientific argument for the need to explore the energy region to be made accessible by the SSC, and a major aim of the workshop was to involve a broad cross section of particle theorists in the ongoing process of sharpening the requirements for both accelerator and detector design that will ensure detection and identification of meaningful signals, whatever form the electroweak symmetry breaking phenomenon should actually take. Separate entries were prepared for the data base for the papers presented.

Defense of the Romantic Poet? Writing Workshops and Voice.

Science.gov (United States)

Lensmire, Timothy J.; Satanovsky, Lisa

1998-01-01

Discusses four Romantic themes that are crucial to writing workshop practice (self-expression, liberation from convention, celebration of emotion, and a valuing of folk cultures), explaining how the writing workshop approach embodies these themes; summarizing criticisms of these approaches; sketching a conception of student voice that looks…

77 FR 26511 - Announcing a National Cybersecurity Center of Excellence (NCCoE) Workshop

Science.gov (United States)

2012-05-04

... Cybersecurity Center of Excellence (NCCoE) Workshop AGENCY: National Institute of Standards and Technology (NIST... Cybersecurity Center of Excellence (NCCoE) Workshop to be held on Tuesday, June 26, 2012. This is an initial... accelerating the widespread adoption of integrated cybersecurity tools and technologies. The NCCoE will bring...

Accelerator technology working group summary

International Nuclear Information System (INIS)

Jameson, R.A.

1985-01-01

A summary is presented of workshop deliberations on basic scaling, the economic viability of laser drive power for HEP accelerators, the availability of electron beam injectors for near-term experiments, and a few very general remarks on technology issues

The generation of high fields for particle acceleration to very high energies

International Nuclear Information System (INIS)

1985-01-01

A Workshop organised by the CERN Accelerator School, the European Committee for Future Accelerators and the Istituto Nazionale di Fisica Nucleare was held at the Frascati laboratory of INFN during the last week of September 1984. Its purpose was to bring together an inter-disciplinary group of physicists to review ideas for the acceleration of particles to energies beyond those attainable in machines whose construction is underway, or is currently contemplated. These proceedings contain some of the material presented and discussed at the Workshop, comprising papers on topics such as: the free-electron-laser, the lasertron, wakefield accelerators, the laser excitation of droplet arrays, a switched-power linac, plasma beat-wave accelerators and the choice of basic parameters for linear colliders intended for the TeV energy region. (orig.)

Accelerator development

International Nuclear Information System (INIS)

Anon.

1975-01-01

Because the use of accelerated heavy ions would provide many opportunities for new and important studies in nuclear physics and nuclear chemistry, as well as other disciplines, both the Chemistry and Physics Divisions are supporting the development of a heavy-ion accelerator. The design of greatest current interest includes a tandem accelerator with a terminal voltage of approximately 25 MV injecting into a linear accelerator with rf superconducting resonators. This combined accelerator facility would be capable of accelerating ions of masses ranging over the entire periodic table to an energy corresponding to approximately 10 MeV/nucleon. This approach, as compared to other concepts, has the advantages of lower construction costs, lower operating power, 100 percent duty factor, and high beam quality (good energy resolution, good timing resolution, small beam size, and small beam divergence). The included sections describe the concept of the proposed heavy-ion accelerator, and the development program aiming at: (1) investigation of the individual questions concerning the superconducting accelerating resonators; (2) construction and testing of prototype accelerator systems; and (3) search for economical solutions to engineering problems. (U.S.)

Workshop on beam cooling and related topics

International Nuclear Information System (INIS)

Bosser, J.

1994-01-01

The sessions of the Workshop on Beam Cooling and Related Topics, held in Montreux from 4-8 October 1993, are reported in these Proceedings. This meeting brought together international experts in the field of accelerator beam cooling. Its purpose was to discuss the status of the different cooling techniques currently in use (stochastic, electron, ionization, heavy-ion, and laser) and their actual performances, technological implications, and future prospects. Certain theoretical principles (muon cooling, cyclotron maser cooling) were discussed and are reported on in these Proceedings. Also of interest in this Workshop was the possibility of beam crystallization in accelerators using ultimate cooling. In the first part of these Proceedings, overview talks on the various cooling techniques, their implications, present performance, and future prospects are presented. More detailed reports on all the topics are then given in the form of oral presentations or poster sessions. Finally, the chairmen and/or convenors then present summary talks. (orig.)

Future Accelerators Seminar in Japan

Energy Technology Data Exchange (ETDEWEB)

Anon.

1984-10-15

ICFA, the International Committee for Future Accelerators, was set up by the Particles and Fields Commission of the International Union of Pure and Applied Physics (IUPAP) in 1976. Its mandate was 'To organize workshops for the study of problems related to an international super-high energy accelerator complex (VBA) and to elaborate the framework of its construction and of its use. To organize meetings for the exchange of information on future plans of regional facilities and for the formulation of advice on joint studies and uses.' In the seven years of its existence (it first met in August 1977), ICFA has organized three workshops on the first topic — t w o on 'Possibilities and Limitations of Accelerators and Detectors' (Fermilab, 1978 and Les Diablerets, 1979) and one on 'Possibilities and Limitations for Superconducting Accelerator Magnets' (Protvino, 1981). At an ICFA meeting at Fermilab in August 1983, it was realized that the second topic had been somewhat neglected. It was therefore decided to postpone a fourth workshop scheduled at the Japanese National Laboratory for High Energy Physics (KEK) and to organize instead a Seminar on 'Future Perspectives in High Energy Physics' similar to that held in New Orleans in 1975, which had in fact led to the creation of ICFA.The Seminar (jointly hosted by the Institute of Nuclear Study of Tokyo University and KEK, with support from the Ministry of Education, Science and Culture, the Yamada Science Foundation and the Nishina Memorial Foundation) took place from 14-20 May. There were about a hundred participants, mostly senior scientists from Western and Eastern Europe, USA, USSR and Japan (including the Directors of almost all the major high energy physics Laboratories) and representatives from Australia, Canada, China, India, Mexico, South Korea and Vietnam.

Future Accelerators Seminar in Japan

International Nuclear Information System (INIS)

Anon.

1984-01-01

ICFA, the International Committee for Future Accelerators, was set up by the Particles and Fields Commission of the International Union of Pure and Applied Physics (IUPAP) in 1976. Its mandate was 'To organize workshops for the study of problems related to an international super-high energy accelerator complex (VBA) and to elaborate the framework of its construction and of its use. To organize meetings for the exchange of information on future plans of regional facilities and for the formulation of advice on joint studies and uses.' In the seven years of its existence (it first met in August 1977), ICFA has organized three workshops on the first topic — t w o on 'Possibilities and Limitations of Accelerators and Detectors' (Fermilab, 1978 and Les Diablerets, 1979) and one on 'Possibilities and Limitations for Superconducting Accelerator Magnets' (Protvino, 1981). At an ICFA meeting at Fermilab in August 1983, it was realized that the second topic had been somewhat neglected. It was therefore decided to postpone a fourth workshop scheduled at the Japanese National Laboratory for High Energy Physics (KEK) and to organize instead a Seminar on 'Future Perspectives in High Energy Physics' similar to that held in New Orleans in 1975, which had in fact led to the creation of ICFA.The Seminar (jointly hosted by the Institute of Nuclear Study of Tokyo University and KEK, with support from the Ministry of Education, Science and Culture, the Yamada Science Foundation and the Nishina Memorial Foundation) took place from 14-20 May. There were about a hundred participants, mostly senior scientists from Western and Eastern Europe, USA, USSR and Japan (including the Directors of almost all the major high energy physics Laboratories) and representatives from Australia, Canada, China, India, Mexico, South Korea and Vietnam

Executive Summary High-Yield Scenario Workshop Series Report

Energy Technology Data Exchange (ETDEWEB)

Leslie Park Ovard; Thomas H. Ulrich; David J. Muth Jr.; J. Richard Hess; Steven Thomas; Bryce Stokes

2009-12-01

To get a collective sense of the impact of research and development (R&D) on biomass resource availability, and to determine the feasibility that yields higher than baseline assumptions used for past assessments could be achieved to support U.S. energy independence, an alternate “High-Yield Scenario” (HYS) concept was presented to industry experts at a series of workshops held in December 2009. The workshops explored future production of corn/agricultural crop residues, herbaceous energy crops (HECs), and woody energy crops (WECs). This executive summary reports the findings of that workshop.

TARG2 Workshop - Slides of the presentations

International Nuclear Information System (INIS)

Malka, V.; Koehler, A.; Beaurepaire, B.; Krishnan, M.; Guillaume, E.; Chowdhury, E.; Volpe, L.; Nakatsutsumi, M.; Chatain, D.; Legare, F.; Wachulak, P.; Bocoum, M.; Leblanc, A.; Schreiber, J.; Ter-Avetisyan, S.; Zeil, K.; Fukuda, Y.; Levecq, X.; Svensson, K.; Mollica, F.; Brandi, F.; Ruiz, C.

2016-01-01

The topics tackled in this workshop involved: laser-plasma interaction, innovative targets from gases to solids, targetry recycling and debris management, mass fabrication of laser targets, high repetition rate capability, integrated plasma diagnostics, wakefield acceleration and radiation sources. This document is made up of the slides of the presentations

Plasma based accelerators

Energy Technology Data Exchange (ETDEWEB)

Caldwell, Allen [Max-Planck-Institut fuer Physik, Muenchen (Germany)

2015-05-01

The concept of laser-induced plasma wakefields as a technique to accelerate charged particles was introduced 35 years ago as a means to go beyond the accelerating gradients possible with metallic cavities supporting radio frequency electromagnetic fields. Significant developments in laser technology have made possible the pulse intensity needed to realize this concept, and rapid progress is now underway in the realization of laser-driven plasma wakefield acceleration. It has also been realized that similar accelerating gradients can be produced by particle beams propagating in plasmas, and experimental programs have also been undertaken to study this possibility. Positive results have been achieved with electron-driven plasma wakefields, and a demonstration experiment with proton-driven wakefields is under construction at CERN. The concepts behind these different schemes and their pros and cons are described, as well as the experimental results achieved. An outlook for future practical uses of plasma based accelerators will also be given.

ECRIPAC: A new concept for the production and acceleration to very high energies of multiply charged ions using an ECR plasma

International Nuclear Information System (INIS)

Geller, R.; Golovanivsky, K.; Melin, G.

1991-01-01

A concept of a new ECR device aimed to produce pulsed beams of ions accelerated up to 0.5 GeV/nucleon without the help of any conventional accelerator is exposed. The main idea is the conjunction of two fundamental physical principles experienced formerly in the PLEIADE and GYRAC devices. With the new concept the authors propose to produce, using a very compact device, high energy ion beams with energies and intensities adequate for particle, nuclear and atomic physics as well as for modern technologies and medicine

Mitochondrial DNA and Cancer Epidemiology Workshop

Science.gov (United States)

A workshop to review the state-of-the science in the mitochondrial DNA field and its use in cancer epidemiology, and to develop a concept for a research initiative on mitochondrial DNA and cancer epidemiology.

Workshop on physics at future accelerators

International Nuclear Information System (INIS)

1987-01-01

A workshop took place at La Thuile and at CERN in January 1987 to study the physics potential of three types of particle collider with energies in the TeV region, together with the feasibility of experiments with them. The machines were: a large hadron collider (LHC) placed in the LEP tunnel at CERN, with a total proton-proton centre-of-mass energy of about 16 TeV; an electron-proton collider, using the LHC and LEP, with a centre-of-mass energy in the range 1.3 TeV to 1.8 TeV; and an electron-positron linear collider with centre-of-mass energy about 2 TeV. The summary talks given at CERN by the conveners of the study groups are contained in volume I of the proceedings; the present volume is devoted to the contributions from the participants at La Thuile. These give details of the studies carried out on the new phenomena which might be observed at the new machines and the technical feasibility of possible experiments. (orig.)

Concept of a staged FEL enabled by fast synchrotron radiation cooling of laser-plasma accelerated beam by solenoidal magnetic fields in plasma bubble

Science.gov (United States)

Seryi, Andrei; Lesz, Zsolt; Andreev, Alexander; Konoplev, Ivan

2017-03-01

A novel method for generating GigaGauss solenoidal fields in a laser-plasma bubble, using screw-shaped laser pulses, has been recently presented. Such magnetic fields enable fast synchrotron radiation cooling of the beam emittance of laser-plasma accelerated leptons. This recent finding opens a novel approach for design of laser-plasma FELs or colliders, where the acceleration stages are interleaved with laser-plasma emittance cooling stages. In this concept paper, we present an outline of what a staged plasma-acceleration FEL could look like, and discuss further studies needed to investigate the feasibility of the concept in detail.

SIMS applications workshop. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-04-01

The first ANSTO/AINSE SIMS Workshop drew together a mixture of Surface Analysis experts and Surface Analysis users with the concept that SIMS analysis has to be enfolded within the spectrum of surface analysis techniques and that the user should select the technique most applicable to the problem. With this concept in mind the program was structured as sessions on SIMS Facilities; Applications to Mineral Surfaces; Applications to Biological Systems, Applications to Surfaces as Semi- conductors, Catalysts and Surface Coatings; and Applications to Ceramics

Proceedings of the workshop on negative ion formation and beam handling

International Nuclear Information System (INIS)

Takagi, A.; Mori, Y.

1993-01-01

The Workshop on Negative Ion Formation and Beam Handling was held at National Laboratory for High Energy Physics (KEK) on July 27 and 28. More than 40 participants attended the workshop. Negative ions and beams are becoming very useful and attractive in many fields of science, in particular in accelerator science and nuclear fusion and various types of negative ion sources have been developed so far. However, the fundamental mechanisms of negative ion generation in the ion sources and of beam formation are still not clear. This workshop aimed to discuss the problems on these points in details. (J.P.N.)

Grid and Entrepreneurship Workshop

CERN Multimedia

2006-01-01

The CERN openlab is organising a special workshop about Grid opportunities for entrepreneurship. This one-day event will provide an overview of what is involved in spin-off technology, with a special reference to the context of computing and data Grids. Lectures by experienced entrepreneurs will introduce the key concepts of entrepreneurship and review, in particular, the industrial potential of EGEE (the EU co-funded Enabling Grids for E-sciencE project, led by CERN). Case studies will be given by CEOs of European start-ups already active in the Grid and computing cluster area, and regional experts will provide an overview of efforts in several European regions to stimulate entrepreneurship. This workshop is designed to encourage students and researchers involved or interested in Grid technology to consider the entrepreneurial opportunities that this technology may create in the coming years. This workshop is organized as part of the CERN openlab student programme, which is co-sponsored by CERN, HP, ...

PREFACE: 6th Workshop on Infrared Spectroscopy and Microscopy with Accelerator-Based Sources (WIRMS11)

Science.gov (United States)

Lupi, Stefano; Perucchi, Andrea

2012-05-01

This volume of Journal of Physics: Conference Series is dedicated to a subset of papers related to the work presented at the 6th edition of the international Workshop on Infrared Spectroscopy and Microscopy with Accelerator-Based Sources (WIRMS), held in Trieste, Italy, September 4-8 2011. Previous editions of the conference were held in Porquerolles (France), Lake Tahoe (USA), Rathen (Germany), Awaji (Japan), and Banff (Canada). This edition was organized and chaired by Stefano Lupi (Roma La Sapienza) and co-chaired by Andrea Perucchi (Elettra), with the support of the Italian Synchrotron Light Laboratory ELETTRA, which was honored to host the WIRMS workshop in its tenth anniversary. The 6th WIRMS edition addressed several different topics, ranging from biochemistry to strongly correlated materials, from geology to conservation science, and from forensics to the study of cometary dusts. Representatives from the infrared scientific programs at synchrotron light sources and free-electron-laser facilities. This edition was attended by 88 participants, including representatives from the infrared scientific programs at synchrotron light sources and free-electron-laser facilities, who enjoyed the stimulating scientific presentations, several detailed discussions, and the beautiful weather and scenery of the Trieste gulf. Participants came from 16 different nations and four continents, including many young scientists, six of which were supported by the organizers. There were 45 scientific talks divided in 11 sessions: Facilities, Microspectroscopy (I, II, III), Time-Resolved Spectroscopies, Extreme Conditions, Condensed Matter, Near-Field, Imaging, THz Techniques and High-Resolution Spectroscopy. 37 posters were also presented at two very lively evening poster sessions. We would like to use the opportunity of writing this preface to thank all the participants of the workshop for the very high level of their scientific contribution and for the very friendly atmosphere

Workshop on momentum distributions: Summary

International Nuclear Information System (INIS)

Simmons, R.O.

1988-01-01

This has been an extraordinary Workshop touching many branches of physics. The Workshop has treated momentum distributions in fluid and solid condensed matter, in nuclei, and in electronic systems. Both theoretical and experimental concepts and methods have been considered in all these branches. A variety of specific illustrations and applications in physical systems have been presented. One finds that some common unifying themes emerge. One finds, also, that some examples are available to illustrate where one branch is more mature than others and to contrast where expectations for future progress may be most encouraged. 6 refs., 2 figs

Virtual accelerator concept, implementation and preliminary test

International Nuclear Information System (INIS)

Uriot, D.; Duperrier, R.

2006-05-01

A virtual accelerator is the coupling of a simulation code with the control system of a real machine. 3 operating modes are considered. First, the monitoring mode in which any action on the control system has an impact on both real and virtual machines. This mode allows a direct comparison between simulation results and the real behaviour of the accelerator. Secondly, the flight simulation mode, this mode allows the accelerator operators to simulate the effect of any change in the parameters of the control system before transferring them to the real machine. The main advantage of this mode is to allow the assessment of operating procedures before implementing them on the real machine. The third mode is the automatic steering mode in which the simulation code assumes the reins of the control system of the real machine. This mode allows the making of complex and time-consuming adjustment procedures in an automatic way. TraceWin is a simulation code dedicated to the behaviour of charged-particle beams in a linear accelerator. TraceWin is consistent with the EPICS technology on which the control system of most accelerators is based. A virtual accelerator composed of the SILHI injector combined to the TraceWin code via the EPICS environment has showed its efficiency in the automatic steering mode. (A.C.)

Proceedings of the workshop on program options in intermediate-energy physics. Volume 1. Summary and panel reports

Energy Technology Data Exchange (ETDEWEB)

Allred, J.C.; Talley, B. (comps.)

1980-05-01

A Workshop on Program Options in Intermediate-Energy Physics sponsored by the US Department of Energy was held at Los Alamos Scientific Laboratory, August 20 to 31, 1979. The scope of the workshop included all laboratories in intermediate-energy physics, worldwide, and all of these sent representatives to the workshop. The workshop addressed itself to the critical questions on nuclear and particle physics and how they can best be investigated by intermediate-energy accelerators. Among the questions that the workshop members considered were: (1) what are the important physics topics which might be understood through research on these accelerators in the next 10 years. These topics include, but are not restricted to, fundamental interactions and symmetries in particle physics, and nuclear modes of motion, structure, and reaction mechanisms; (2) what experiments should be undertaken to carry out the program. What are the kinematical conditions, accuracies, resolutions, and other parameters required to obtain the desired knowledge; (3) which accelerators are best suited for each experiment. What work at other laboratories (low-, intermediate-, or high-energy) could be undertaken to complement and/or supplement the proposed LAMPF program; and (4) what new facility capabilities should be explored for the long-term future. The workshop was divided into small panels in order to promote effective interchange of ideas. After reports to other panels and plenary sessions, the panelists prepared reports stating the results of their deliberations. These reports comprise the principal part of Volume I.

Proceedings of the workshop on program options in intermediate-energy physics. Volume 1. Summary and panel reports

International Nuclear Information System (INIS)

Allred, J.C.; Talley, B.

1980-05-01

A Workshop on Program Options in Intermediate-Energy Physics sponsored by the US Department of Energy was held at Los Alamos Scientific Laboratory, August 20 to 31, 1979. The scope of the workshop included all laboratories in intermediate-energy physics, worldwide, and all of these sent representatives to the workshop. The workshop addressed itself to the critical questions on nuclear and particle physics and how they can best be investigated by intermediate-energy accelerators. Among the questions that the workshop members considered were: (1) what are the important physics topics which might be understood through research on these accelerators in the next 10 years. These topics include, but are not restricted to, fundamental interactions and symmetries in particle physics, and nuclear modes of motion, structure, and reaction mechanisms; (2) what experiments should be undertaken to carry out the program. What are the kinematical conditions, accuracies, resolutions, and other parameters required to obtain the desired knowledge; (3) which accelerators are best suited for each experiment. What work at other laboratories (low-, intermediate-, or high-energy) could be undertaken to complement and/or supplement the proposed LAMPF program; and (4) what new facility capabilities should be explored for the long-term future. The workshop was divided into small panels in order to promote effective interchange of ideas. After reports to other panels and plenary sessions, the panelists prepared reports stating the results of their deliberations. These reports comprise the principal part of Volume I

EMSL and Institute for Integrated Catalysis (IIC) Catalysis Workshop

Energy Technology Data Exchange (ETDEWEB)

Campbell, Charles T.; Datye, Abhaya K.; Henkelman, Graeme A.; Lobo, Raul F.; Schneider, William F.; Spicer, Leonard D.; Tysoe, Wilfred T.; Vohs, John M.; Baer, Donald R.; Hoyt, David W.; Thevuthasan, Suntharampillai; Mueller, Karl T.; Wang, Chong M.; Washton, Nancy M.; Lyubinetsky, Igor; Teller, Raymond G.; Andersen, Amity; Govind, Niranjan; Kowalski, Karol; Kabius, Bernd C.; Wang, Hongfei; Campbell, Allison A.; Shelton, William A.; Bylaska, Eric J.; Peden, Charles HF; Wang, Yong; King, David L.; Henderson, Michael A.; Rousseau, Roger J.; Szanyi, Janos; Dohnalek, Zdenek; Mei, Donghai; Garrett, Bruce C.; Ray, Douglas; Futrell, Jean H.; Laskin, Julia; DuBois, Daniel L.; Kuprat, Laura R.; Plata, Charity

2011-05-24

Within the context of significantly accelerating scientific progress in research areas that address important societal problems, a workshop was held in November 2010 at EMSL to identify specific and topically important areas of research and capability needs in catalysis-related science.

Proceedings of the Eighteenth Annual Software Engineering Workshop

Science.gov (United States)

1993-01-01

The workshop provided a forum for software practitioners from around the world to exchange information on the measurement, use, and evaluation of software methods, models, and tools. This year, approximately 450 people attended the workshop, which consisted of six sessions on the following topics: the Software Engineering Laboratory, measurement, technology assessment, advanced concepts, process, and software engineering issues in NASA. Three presentations were given in each of the topic areas. The content of those presentations and the research papers detailing the work reported are included in these proceedings. The workshop concluded with a tutorial session on how to start an Experience Factory.

Proceedings of the Advanced Hadron Facility accelerator design workshop, February 20--25, 1989

International Nuclear Information System (INIS)

Thiessen, H.A.

1990-04-01

The International Workshop on Hadron Facility Technology was held February 20--25, 1989, at the Study Center at Los Alamos National Laboratory. This volume (first of two) included papers on architecture, beam diagnostics, compressors, and linacs. Participants included groups from AHF, Brookhaven National Laboratory, European Hadron Facility, Fermilab, and the Moscow Meson Factory. The workshop was well attended by members of the Los Alamos staff. The interchange of information and the opportunity by criticism by peers was important to all who attended

Summary of longitudinal instabilities workshop

Energy Technology Data Exchange (ETDEWEB)

Chasman, R.

1976-01-01

A five-day ISABELLE workshop on longitudinal instabilities was held at Brookhaven, August 9-13, 1976. About a dozen outside accelerator experts, both from Europe and the U.S.A., joined the local staff for discussions of longitudinal instabilities in ISABELLE. An agenda of talks was scheduled for the first day of the workshop. Later during the week, a presentation was given on the subject ''A more rigorous treatment of Landau damping in longitudinal beam instabilities''. A few progress meetings were held in which disagreements regarding calculations of coupling impedances were clarified. A summary session was held on the last day. Heavy emphasis was put on single bunched beam instabilities in the microwave region extending above the cut-off frequency of the ISABELLE vacuum chamber.

Summary of the very large hadron collider physics and detector workshop

International Nuclear Information System (INIS)

Anderson, G.; Berger, M.; Brandt, A.; Eno, S.

1997-01-01

One of the options for an accelerator beyond the LHC is a hadron collider with higher energy. Work is going on to explore accelerator technologies that would make such a machine feasible. This workshop concentrated on the physics and detector issues associated with a hadron collider with an energy in the center of mass of the order of 100 to 200 TeV

10 workshops on Immunology of preeclampsia.

Science.gov (United States)

Gerard, Chaouat

2017-09-01

For the 10th issue of the « island workshops », now the Reunion Workshops, organised by Pierre Yves Robillard since the first one in Tahiti challenging the "vascular disease only" theory of pre eclampsia and introducing the primipaternity concept, we examined the reasons for considering an Immunological approach to the disease. This (brief) overview thus examines several important topics in an Immunological framework. I have chosen to present here the evolution of the main themes rather than a purely chronological vision. Copyright © 2017. Published by Elsevier B.V.

Post-LHC accelerator magnets

International Nuclear Information System (INIS)

Gourlay, Stephen A.

2001-01-01

The design and practicality of future accelerators, such as hadron colliders and neutrino factories being considered to supercede the LHC, will depend greatly on the choice of superconducting magnets. Various possibilities will be reviewed and discussed, taking into account recent progress and projected improvements in magnet design and conductor development along with the recommendations from the 2001 Snowmass workshop

Workshop UNK-600 (proceedings)

International Nuclear Information System (INIS)

Zajtsev, A.M.; Bitykov, S.I.

1994-01-01

Proceedings are presented of the workshop devoted to the accelerating storage complex of IHEP (UNK-600). In the first section is given the information on the present status of the UNK-600 and particle channels design and on the adopted experiment NEPTUN-A. In the papers of the second section are discussed hadron physics investigations at 600 GeV. Experiments in the neutrino and muon beams are analyzed. A possible program of studying the charged kaon rare decays is described

Workshop Results: Teaching Geoscience to K-12 Teachers

Science.gov (United States)

Nahm, A.; Villalobos, J. I.; White, J.; Smith-Konter, B. R.

2012-12-01

A workshop for high school and middle school Earth and Space Science (ESS) teachers was held this summer (2012) as part of an ongoing collaboration between the University of Texas at El Paso (UTEP) and El Paso Community College (EPCC) Departments of Geological Sciences. This collaborative effort aims to build local Earth science literacy and educational support for the geosciences. Sixteen teachers from three school districts from El Paso and southern New Mexico area participated in the workshop, consisting of middle school, high school, early college high school, and dual credit faculty. The majority of the teachers had little to no experience teaching geoscience, thus this workshop provided an introduction to basic geologic concepts to teachers with broad backgrounds, which will result in the introduction of geoscience to many new students each year. The workshop's goal was to provide hands-on activities illustrating basic geologic and scientific concepts currently used in introductory geology labs/lectures at both EPCC and UTEP to help engage pre-college students. Activities chosen for the workshop were an introduction to Google Earth for use in the classroom, relative age dating and stratigraphy using volcanoes, plate tectonics utilizing the jigsaw pedagogy, and the scientific method as a think-pair-share activity. All activities where designed to be low cost and materials were provided for instructors to take back to their institutions. A list of online resources for teaching materials was also distributed. Before each activity, a short pre-test was given to the participants to gauge their level of knowledge on the subjects. At the end of the workshop, participants were given a post-test, which tested the knowledge gain made by participating in the workshop. In all cases, more correct answers were chosen in the post-test than the individual activity pre-tests, indicating that knowledge of the subjects was gained. The participants enjoyed participating in these

Proceedings of the Advanced Hadron Facility accelerator design workshop, February 20--25, 1989

International Nuclear Information System (INIS)

Thiessen, H.A.

1990-04-01

The International Workshop on Hadron Facility Technology was held February 20--25, 1989, at the Study Center at Los Alamos National Laboratory. This volume (second of two) included papers on computer controls, polarized beam, rf, magnet and power supplies, experimental areas, and instabilities. Participants included groups from AHF, Brookhaven National Laboratory, European Hadron Facility, Fermilab, and the Moscow Meson Factory. The workshop was well attended by members of the Los Alamos staff. The interchange of information and the opportunity by criticism by peers was important to all who attended

Proposed inductive voltage adder based accelerator concepts for the second axis of DARHT

International Nuclear Information System (INIS)

Smith, D.L.; Johnson, D.L.; Boyes, J.D.

1997-01-01

As participants in the Technology Options Study for the second axis of the Dual Axis Radiographic HydroTest (DARHT) facility located at Los Alamos National Laboratories, the authors have considered several accelerator concepts based on the Inductive Voltage Adder (IVA) technology that is being used successfully at Sandia on the SABRE and HERMES-III facilities. The challenging accelerator design requirements for the IVA approach include: ≥12-MeV beam energy; ∼60-ns electrical pulse width; ≤40-kA electron beam current; ∼1-mm diameter e-beam; four pulses on the same axis or as close as possible to that axis; and an architecture that fits within the existing building envelope. To satisfy these requirements the IVA concepts take a modular approach. The basic idea is built upon a conservative design for eight ferromagnetically isolated 2-MV cavities that are driven by two 3 to 4-Ω water dielectric pulse forming lines (PFLs) synchronized with laser triggered gas switches. The 100-Ω vacuum magnetically insulated transmission line (MITL) would taper to a needle cathode that produces the electron beam(s). After considering many concepts the authors narrowed their study to the following options: (A) Four independent single pulse drivers powering four single pulse diodes; (B) Four series adders with interleaved cavities feeding a common MITL and diode; (C) Four stages of series PFLs, isolated from each other by triggered spark gap switches, with single-point feeds to a common adder, MITL, and diode; and (D) Isolated PFLs with multiple-feeds to a common adder using spark gap switches in combination with saturable magnetic cores to isolate the non-energized lines. The authors will discuss these options in greater detail identifying the challenges and risks associated with each

Proceedings of the SLAC/KEK ATF lattice workshop

International Nuclear Information System (INIS)

Urakawa, Junji

1993-04-01

The SLAC/KEK ATF Lattice Workshop was held on December 8-11, 1992 at KEK, National Laboratory for High Energy Physics. The purpose of this workshop is to critically review the ATF lattice design for any possible improvements, and also to bring SLAC colleagues up to date on recent progress at KEK. At KEK studies on intense multi-bunch beam acceleration and emittance reduction have been actively pursued, evolving into the ATF project since 1990. In 1991 we have launched a large scale reconstruction of the experimental hall. This is to build the shielded housing for the 1.54 GeV injector linac and the test damping ring. Our plan is to begin construction of the linac in March 1993. Some results from the discussions during the Workshop have been already incorporated in the revised ATF lattice design. (J.P.N.)

Emerging concepts in biomarker discovery; The US-Japan workshop on immunological molecular markers in oncology

Science.gov (United States)

Tahara, Hideaki; Sato, Marimo; Thurin, Magdalena; Wang, Ena; Butterfield, Lisa H; Disis, Mary L; Fox, Bernard A; Lee, Peter P; Khleif, Samir N; Wigginton, Jon M; Ambs, Stefan; Akutsu, Yasunori; Chaussabel, Damien; Doki, Yuichiro; Eremin, Oleg; Fridman, Wolf Hervé; Hirohashi, Yoshihiko; Imai, Kohzoh; Jacobson, James; Jinushi, Masahisa; Kanamoto, Akira; Kashani-Sabet, Mohammed; Kato, Kazunori; Kawakami, Yutaka; Kirkwood, John M; Kleen, Thomas O; Lehmann, Paul V; Liotta, Lance; Lotze, Michael T; Maio, Michele; Malyguine, Anatoli; Masucci, Giuseppe; Matsubara, Hisahiro; Mayrand-Chung, Shawmarie; Nakamura, Kiminori; Nishikawa, Hiroyoshi; Palucka, A Karolina; Petricoin, Emanuel F; Pos, Zoltan; Ribas, Antoni; Rivoltini, Licia; Sato, Noriyuki; Shiku, Hiroshi; Slingluff, Craig L; Streicher, Howard; Stroncek, David F; Takeuchi, Hiroya; Toyota, Minoru; Wada, Hisashi; Wu, Xifeng; Wulfkuhle, Julia; Yaguchi, Tomonori; Zeskind, Benjamin; Zhao, Yingdong; Zocca, Mai-Britt; Marincola, Francesco M

2009-01-01

Supported by the Office of International Affairs, National Cancer Institute (NCI), the "US-Japan Workshop on Immunological Biomarkers in Oncology" was held in March 2009. The workshop was related to a task force launched by the International Society for the Biological Therapy of Cancer (iSBTc) and the United States Food and Drug Administration (FDA) to identify strategies for biomarker discovery and validation in the field of biotherapy. The effort will culminate on October 28th 2009 in the "iSBTc-FDA-NCI Workshop on Prognostic and Predictive Immunologic Biomarkers in Cancer", which will be held in Washington DC in association with the Annual Meeting. The purposes of the US-Japan workshop were a) to discuss novel approaches to enhance the discovery of predictive and/or prognostic markers in cancer immunotherapy; b) to define the state of the science in biomarker discovery and validation. The participation of Japanese and US scientists provided the opportunity to identify shared or discordant themes across the distinct immune genetic background and the diverse prevalence of disease between the two Nations. Converging concepts were identified: enhanced knowledge of interferon-related pathways was found to be central to the understanding of immune-mediated tissue-specific destruction (TSD) of which tumor rejection is a representative facet. Although the expression of interferon-stimulated genes (ISGs) likely mediates the inflammatory process leading to tumor rejection, it is insufficient by itself and the associated mechanisms need to be identified. It is likely that adaptive immune responses play a broader role in tumor rejection than those strictly related to their antigen-specificity; likely, their primary role is to trigger an acute and tissue-specific inflammatory response at the tumor site that leads to rejection upon recruitment of additional innate and adaptive immune mechanisms. Other candidate systemic and/or tissue-specific biomarkers were recognized that

Emerging concepts in biomarker discovery; The US-Japan workshop on immunological molecular markers in oncology

Directory of Open Access Journals (Sweden)

Rivoltini Licia

2009-06-01

Full Text Available Abstract Supported by the Office of International Affairs, National Cancer Institute (NCI, the "US-Japan Workshop on Immunological Biomarkers in Oncology" was held in March 2009. The workshop was related to a task force launched by the International Society for the Biological Therapy of Cancer (iSBTc and the United States Food and Drug Administration (FDA to identify strategies for biomarker discovery and validation in the field of biotherapy. The effort will culminate on October 28th 2009 in the "iSBTc-FDA-NCI Workshop on Prognostic and Predictive Immunologic Biomarkers in Cancer", which will be held in Washington DC in association with the Annual Meeting. The purposes of the US-Japan workshop were a to discuss novel approaches to enhance the discovery of predictive and/or prognostic markers in cancer immunotherapy; b to define the state of the science in biomarker discovery and validation. The participation of Japanese and US scientists provided the opportunity to identify shared or discordant themes across the distinct immune genetic background and the diverse prevalence of disease between the two Nations. Converging concepts were identified: enhanced knowledge of interferon-related pathways was found to be central to the understanding of immune-mediated tissue-specific destruction (TSD of which tumor rejection is a representative facet. Although the expression of interferon-stimulated genes (ISGs likely mediates the inflammatory process leading to tumor rejection, it is insufficient by itself and the associated mechanisms need to be identified. It is likely that adaptive immune responses play a broader role in tumor rejection than those strictly related to their antigen-specificity; likely, their primary role is to trigger an acute and tissue-specific inflammatory response at the tumor site that leads to rejection upon recruitment of additional innate and adaptive immune mechanisms. Other candidate systemic and/or tissue-specific biomarkers

The Second International Workshop on Squeezed States and Uncertainty Relations

Science.gov (United States)

Han, D. (Editor); Kim, Y. S.; Manko, V. I.

1993-01-01

This conference publication contains the proceedings of the Second International Workshop on Squeezed States and Uncertainty Relations held in Moscow, Russia, on 25-29 May 1992. The purpose of this workshop was to study possible applications of squeezed states of light. The Workshop brought together many active researchers in squeezed states of light and those who may find the concept of squeezed states useful in their research, particularly in understanding the uncertainty relations. It was found at this workshop that the squeezed state has a much broader implication than the two-photon coherent states in quantum optics, since the squeeze transformation is one of the most fundamental transformations in physics.

Workshop on Pion-Kaon Interactions (PKI2018) Mini-Proceedings

Energy Technology Data Exchange (ETDEWEB)

Amaryan, M; Pal, Bilas

2018-02-14

This volume is a short summary of talks given at the PKI2018 Workshop organized to discuss current status and future prospects of pi -K interactions. The precise data on pi K interaction will have a strong impact on strange meson spectroscopy and form factors that are important ingredients in the Dalitz plot analysis of a decays of heavy mesons as well as precision measurement of Vus matrix element and therefore on a test of unitarity in the first raw of the CKM matrix. The workshop has combined the efforts of experimentalists, Lattice QCD, and phenomenology communities. Experimental data relevant to the topic of the workshop were presented from the broad range of different collaborations like CLAS, GlueX, COMPASS, BaBar, BELLE, BESIII, VEPP-2000, and LHCb. One of the main goals of this workshop was to outline a need for a new high intensity and high precision secondary KL beam facility at JLab produced with the 12 GeV electron beam of CEBAF accelerator.

An Investigation of Participation in Weekly Music Workshops and Its Relationship to Academic Self-Concept and Self-Esteem of Middle School Students in Low-Income Communities

Science.gov (United States)

Shin, Jihae

2011-01-01

The purpose of this study was to examine how I Am A Dreamer Musician Program (IDMP) affected academic self-concept and self-esteem of middle school students in low-income communities. During the seven weeks of the weekly music workshops, students participated in different musical activities including playing percussion instruments, singing,…

Electron Cloud Effects in Accelerators

International Nuclear Information System (INIS)

Furman, M A

2013-01-01

We present a brief summary of various aspects of the electron-cloud effect (ECE) in accelerators. For further details, the reader is encouraged to refer to the proceedings of many prior workshops, either dedicated to EC or with significant EC contents, including the entire 'ECLOUD' series. In addition, the proceedings of the various flavors of Particle Accelerator Conferences contain a large number of EC-related publications. The ICFA Beam Dynamics Newsletter series contains one dedicated issue, and several occasional articles, on EC. An extensive reference database is the LHC website on EC. (author)

Proceedings of the workshop on physics at current accelerators and supercolliders

International Nuclear Information System (INIS)

Hewett, J.L.; White, A.R.; Zeppenfeld, D.

1993-01-01

This report contains papers from the workshop on SSC physics. The topics of these papers include: electroweak physics; electroweak symmetry breaking; heavy flavors; searches for new phenomena; strong interactions and full acceptance physics; and event simulation. These paper have been cataloged separately on the data base

Proceedings of the workshop on physics at current accelerators and supercolliders

Energy Technology Data Exchange (ETDEWEB)

Hewett, J L; White, A R; Zeppenfeld, D [eds.

1993-06-02

This report contains papers from the workshop on SSC physics. The topics of these papers include: electroweak physics; electroweak symmetry breaking; heavy flavors; searches for new phenomena; strong interactions and full acceptance physics; and event simulation. These paper have been cataloged separately on the data base.

Summary of the workshop on HOM in SPL, held at CERN June 25-26.

CERN Document Server

Lombardi, A; Weingarten, W

2009-01-01

A mini-workshop on the subject of HOMs in a superconducting proton linac was held at CERN on the 25th and 26th June 2009. The purpose of this workshop was to discuss more specifically the effects of HOMs on beam dynamics in the SPL and comparable accelerators and to provide guidelines for the specification of HOM dampers, if necessary.

Modeling Acceleration of a System of Two Objects Using the Concept of Limits

Science.gov (United States)

Sokolowski, Andrzej

2018-01-01

Traditional school laboratory exercises on a system of moving objects connected by strings involve deriving expressions for the system acceleration, a = (∑F )/m, and sketching a graph of acceleration vs. force. While being in the form of rational functions, these expressions present great opportunities for broadening the scope of the analysis by using a more sophisticated math apparatus—the concept of limits. Using the idea of limits allows for extending both predictions and explanations of this type of motion that are—according to Redish—essential goals of teaching physics. This type of analysis, known in physics as limiting case analysis, allows for generalizing inferences by evaluating or estimating values of algebraic functions based on its extreme inputs. In practice, such transition provides opportunities for deriving valid conclusions for cases when direct laboratory measurements are not possible. While using limits is common for scientists, the idea of applying limits in school practice is not visible, and testing students' ability in this area is also rare.

Clinical requirements and accelerator concepts for BNCT

International Nuclear Information System (INIS)

Ludewigt, B.A.; Bleuel, D.L.; Chu, W.T.; Donahue, R.J.; Kwan, J.; Leung, K.N.; Reginato, L.L.; Wells, R.P.

1997-05-01

Accelerator-based neutron sources are an attractive alternative to nuclear reactors for providing epithermal neutron beams for Boron Neutron Capture Therapy. Based on clinical requirements and neutronics modeling the use of proton and deuteron induced reactions in 7 Li and 9 Be targets has been compared. Excellent epithermal neutron beams can be produced via the 7 Li(p,n) 7 Be reaction at proton energies of ∼2.5 MeV. An electrostatic quadrupole accelerator and a lithium target, which can deliver and handle 2.5 MeV protons at beam currents up to 50 mA, are under development for an accelerator-based BNCT facility at the Lawrence Berkeley National Laboratory

Workshop Report on Managing Solar Radiation

Science.gov (United States)

Lane, Lee (Compiler); Caldeira, Ken (Compiler); Chatfield, Robert (Compiler); Langhoff, Stephanie (Compiler)

2007-01-01

The basic concept of managing Earth's radiation budget is to reduce the amount of incoming solar radiation absorbed by the Earth so as to counterbalance the heating of the Earth that would otherwise result from the accumulation of greenhouse gases. The workshop did not seek to decide whether or under what circumstances solar radiation management should be deployed or which strategies or technologies might be best, if it were deployed. Rather, the workshop focused on defining what kinds of information might be most valuable in allowing policy makers more knowledgeably to address the various options for solar radiation management.

Summary of the CERN Workshop on Materials for Collimators and Beam Absorbers

CERN Document Server

Schmidt, R; Bertarelli, A; Ferrari, A; Weterings, W; Mokhov, N V

2008-01-01

The main focus of the workshop was on collimators and beam absorbers for (mainly) High Energy Hadron Accelerators, with the energy stored in the beams far above damage limit. The objective was to better understand the technological limits imposed by mechanisms related to beam impact on materials. The idea to organise this workshop came up during the High Intensity High Brightness Hadron Beams, ICFA-HB2006 in Japan [1]. The workshop was organised 3-5 September 2007 at CERN, with about 60 participants, including 20 from outside CERN. About 30 presentations were given [2]. The event was driven by the LHC challenge, with more than 360 MJoule stored in each proton beam. The entire beam or its fraction will interact with LHC collimators and beam absorbers, and with the LHC beam dump blocks. Collimators and beam absorbers are also of the interest for other labs and accelerators: - CERN: for the CNGS target, for SPS beam absorbers (extraction protection) and collimators for protecting the transfer line between SPS an...

A new target concept for proton accelerator driven boron neutron capture therapy applications

International Nuclear Information System (INIS)

Powell, J.R.; Ludewig, H.; Todosow, M.; Reich, M.

1998-01-01

A new target concept termed Discs Incorporating Sector Configured Orbiting Sources (DISCOS), is proposed for spallation applications, including BNCT (Boron Neutron Capture Therapy). In the BNCT application a proton beam impacts a sequence of ultra thin lithium DISCOS targets to generate neutrons by the 7 Li(p,n) 7 Be reaction. The proton beam loses only a few keV of its ∼MeV energy as it passes through a given target, and is re-accelerated to its initial energy, by a DC electric field between the targets

US-Japan IEC Workshop on Small Plasma and Accelerator Neutron Sources. Final report

International Nuclear Information System (INIS)

Miley, George H.

2008-01-01

The history of IEC development will be briefly described, and some speculation about future directions will be offered. The origin of IEC is due to the brilliance of Phil Farnsworth, inventor of electronic TV in the US. Early experiments were pioneered in the late 1960s by Robert Hirsch who later became head of the DOE fusion program. At that time studies of IEC physics quickly followed at the University of Illinois and at Penn State University. However, despite many successes in this early work, IEC research died as DOE funding stopped in the mid 1980s. In the early 90's, R. W. Bussard of EMC revived work with a new major project based on a magnetic assisted IEC. While doing supportive studies for that project, G. Miley proposed a grided 'STAR mode' IEC as a neutron source for NAA. This concept was later used commercially by Daimler-Benz in Germany to analysis impurities in incoming ores. This represented a first practical application of the IEC. During this period other research groups at LANL, U of Wisconsin and Kyoto University entered IEC research with innovative new concepts and approaches to IEC physics and applications. Much of this work is documented in the present and in past US-Japan Workshops. At present we stand on the threshold of a new area of IEC applications as neutron source, for isotope production, and as a plasma source. These applications provide a way to continue IEC understanding and technology development with the ultimate goal being a fusion power plant. Indeed, a distinguishing feature of the IEC vs. other fusion confinement approaches is the unique opportunity for 'spin off' applications along the way to a power producing plant.

Proceedings of the workshop on the production and use of intense radioactive beams at the Isospin Laboratory

International Nuclear Information System (INIS)

Garrett, J.D.

1992-01-01

These proceedings report the deliberations of a 3 1/2 day workshop on the Production and Use of Intense Radioactive Ion Beams at the Isospin Laboratory, which was held at the Joint Institute for Heavy Ion Research in Oak Ridge, Tennessee, October 1992. The purpose of this workshop was not to duplicate the programs of other recent radioactive ion beam workshops or international conferences that have focused on the scientific concepts which radioactive beams can, and in fact already are, addressing. Instead, the intent was to address the technical problems associated with the construction of the next generation ISOL facility and to initiate a discussion of the type of experimental equipment that should be developed for such a facility. We have tried to bring together in Oak Ridge the world's experts in radioactive targets/ion sources, light and heavy-ion accelerators, and detection systems. After 1 1/2 days of overview presentations, the participants divided into three discussion groups (Experiments with Radioactive Beams, Target Ion Sources and Mass Separation, and Accelerators-Primary and Secondary) for 1 1/2 days of detailed discussions of the most pertinent issues. The final session was devoted to reports from each of the discussion groups and a general discussion of where to go from here. An outgrowth of these discussions was the establishment of working groups to coordinate future technical developments associated with the pertinent issues. The proceedings include the text of all the overview presentations, reports from each discussion group, as well as contributions from those participants who chose to provide the text of their presentations in the discussion groups and the Concluding Remarks. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database

Proceedings of the workshop on the production and use of intense radioactive beams at the Isospin Laboratory

Energy Technology Data Exchange (ETDEWEB)

Garrett, J.D. [ed.

1992-12-31

These proceedings report the deliberations of a 3 1/2 day workshop on the Production and Use of Intense Radioactive Ion Beams at the Isospin Laboratory, which was held at the Joint Institute for Heavy Ion Research in Oak Ridge, Tennessee, October 1992. The purpose of this workshop was not to duplicate the programs of other recent radioactive ion beam workshops or international conferences that have focused on the scientific concepts which radioactive beams can, and in fact already are, addressing. Instead, the intent was to address the technical problems associated with the construction of the next generation ISOL facility and to initiate a discussion of the type of experimental equipment that should be developed for such a facility. We have tried to bring together in Oak Ridge the world`s experts in radioactive targets/ion sources, light and heavy-ion accelerators, and detection systems. After 1 1/2 days of overview presentations, the participants divided into three discussion groups (Experiments with Radioactive Beams, Target Ion Sources and Mass Separation, and Accelerators-Primary and Secondary) for 1 1/2 days of detailed discussions of the most pertinent issues. The final session was devoted to reports from each of the discussion groups and a general discussion of where to go from here. An outgrowth of these discussions was the establishment of working groups to coordinate future technical developments associated with the pertinent issues. The proceedings include the text of all the overview presentations, reports from each discussion group, as well as contributions from those participants who chose to provide the text of their presentations in the discussion groups and the Concluding Remarks. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

The Tasse concept (thorium based accelerator driven system with simplified fuel cycle for long term energy production)

International Nuclear Information System (INIS)

Berthou, V.; Slessarev, I.; Salvatores, M.

2001-01-01

Within the framework of the nuclear waste management studies, the ''one-component''. concept has to be considered as an attractive option in the long-term perspective. This paper proposes a new system called TASSE (''Thorium based Accelerator driven System with Simplified fuel cycle for long term Energy production''.), destined to the current French park renewal. The main idea of the TASSE concept is to simplify both the front and the back end of the fuel cycle, and his major goals are to provide electricity with low waste production, and with an economical competitiveness. (author)

International Social Pharmacy Workshop

OpenAIRE

Cordina, Maria; Journal of the Malta College of Pharmacy Practice Editorial Board

2003-01-01

The Malta College of Pharmacy Practice, will be hosting the 13th International Social Pharmacy Workshop next summer. The concept of social pharmacy is very clearly explained in the article by Professor Ellen West Sørensen and colleagues, who are considered to be pioneers in this field. Malta has successfully hosted a number of pharmacy conferences, however this one is somewhat different and rather special.

Proceedings of the IEA-technical workshop for an international fusion materials irradiation facility. IEA-implementing agreement for a programme of research and development on fusion materials

International Nuclear Information System (INIS)

Ehrlich, K.; Lindau, R.

1995-07-01

The workshop was initiated to deal with the following objectives: (1) Critical review of the requirements for IFMIF from the user's point of view; (2) Definition of a baseline concept for the CDA-study; (3) Formation of working groups for main fields of activities; (4) Identification of tasks and critical issues for main components; (5) Development of a working break-down structure, distribution of work and milestones for CDA-activities; (6) Documentation of main results. According to the enclosed agenda the mission for a Conceptual Design Study, the requirements for an intense neutron source from the user's point of view and the baseline concept for an accelerator-driven D-Li neutron source were discussed in several plenary sessions. In three subgroups (SG 1 Accelerators, SG2 Lithium Target and SG3 Users and Test Cell) technical concepts for the different components and facilities were discussed in detail, critical issues and tasks for the concept study were identified. Finally, the sharing of tasks to the different national parties, questions of organisation of the work, flow of information and definition of milestones was agreed upon. The detailled summary reports of the subgroups and the contributions of the plenary sessions are presented in the proceedings. (orig./HP)

High intensity hadron accelerators

International Nuclear Information System (INIS)

Teng, L.C.

1989-05-01

This rapporteur report consists mainly of two parts. Part I is an abridged review of the status of all High Intensity Hadron Accelerator projects in the world in semi-tabulated form for quick reference and comparison. Part II is a brief discussion of the salient features of the different technologies involved. The discussion is based mainly on my personal experiences and opinions, tempered, I hope, by the discussions I participated in in the various parallel sessions of the workshop. In addition, appended at the end is my evaluation and expression of the merits of high intensity hadron accelerators as research facilities for nuclear and particle physics

Proceedings of the 1979 workshop on beam current limitations in storage rings, July 16-27, 1979

International Nuclear Information System (INIS)

Pellegrini, C.

1979-01-01

The Workshop on Beam Current Limitations in Storage Rings was held at Brookhaven National Laboratory from July 16 to 27, 1979. The purpose of this Workshop was to discuss the physical mechanisms limiting the beam current or current density in accelerators or storage rings. Many of these machines are now being built or planned for a variety of applications, such as colliding beam experiments, synchrotron light production, heavy ion beams. This diversity was reflected in the Workshop and in the papers which have been contributed to these Proceedings. The twenty-one papers from the workshop were incorporated individually in the data base

SuperB Progress Reports Accelerator

CERN Document Server

Biagini, Maria Enrica; Boscolo, M; Buonomo, B; Demma, T; Drago, A; Esposito, M; Guiducci, S; Mazzitelli, G; Pellegrino, L; Preger, M A; Raimondi, P; Ricci, R; Rotundo, U; Sanelli, C; Serio, M; Stella, A; Tomassini, S; Zobov, M; Bertsche, K; Brachman, A; Cai, Y; Chao, A; Chesnut, R; Donald, M.H; Field, C; Fisher, A; Kharakh, D; Krasnykh, A; Moffeit, K; Nosochkov, Y; Pivi, M; Seeman, J; Sullivan, M.K; Weathersby, S; Weidemann, A; Weisend, J; Wienands, U; Wittmer, W; Woods, M; Yocky, G; Bogomiagkov, A; Koop, I; Levichev, E; Nikitin, S; Okunev, I; Piminov, P; Sinyatkin, S; Shatilov, D; Vobly, P; Bosi, F; Liuzzo, S; Paoloni, E; Bonis, J; Chehab, R; Le Meur, G; Lepercq, P; Letellier-Cohen, F; Mercier, B; Poirier, F; Prevost, C; Rimbault, C; Touze, F; Variola, A; Bolzon, B; Brunetti, L; Jeremie, A; Baylac, M; Bourrion, O; De Conto, J M; Gomez, Y; Meot, F; Monseu, N; Tourres, D; Vescovi, C; Chanci, A; Napoly, O; Barber, D P; Bettoni, S; Quatraro, D

2010-01-01

This report details the present status of the Accelerator design for the SuperB Project. It is one of four separate progress reports that, taken collectively, describe progress made on the SuperB Project since the publication of the SuperB Conceptual Design Report in 2007 and the Proceedings of SuperB Workshop VI in Valencia in 2008.

Leadership Workshops for Adult Girl Scout Leaders

Science.gov (United States)

Lebofsky, Larry A.; McCarthy, Donald; DeVore, Edna; Harman, Pamela; Reaching Stars Team

2016-10-01

This year, the University of Arizona is conducting its first two Leadership Workshops for Girl Scout adult leaders. These workshops are being supported by a five-year NASA Collaborative Agreement, Reaching for the Stars: NASA Science for Girl Scouts (www.seti.org/GirlScoutStars), through the SETI Institute in collaboration with the University of Arizona, Girl Scouts of the USA (GSUSA), the Girl Scouts of Northern California, the Astronomical Society of the Pacific, and Aries Scientific, Inc. These workshops are an outgrowth of Astronomy Camp for Girl Scout Leaders, a 14-year "Train the Trainer" program funded by NASA through the James Webb Space Telescope's Near Infrared Camera (NIRCam) education and outreach team. We are continuing our long-term relationship with all Girl Scout Councils to engage girls and young women not only in science and math education, but also in the astronomical and technological concepts relating to NASA's scientific mission. Our training aligns with the GSUSA Journey: It's Your Planet-Love It! and introduces participants to some of the activities that are being developed by the Girl Scout Stars team for GSUSA's new space science badges for all Girl Scout levels being developed as a part of Reaching for the Stars: NASA Science for Girl Scouts.The workshops include hands-on activities in basic astronomy (night sky, stars, galaxies, optics, telescopes, etc.) as well as some more advanced concepts such as lookback time and the expansion of the Universe. Since the inception of our original Astronomy Camp in 2003, our team has grown to include nearly 280 adult leaders, staff, and volunteers from over 79 Councils in 43 states and the District of Columbia so they can, in turn, teach young women essential concepts in astronomy, the night sky environment, applied math, and engineering. Our workshops model what astronomers do by engaging participants in the process of science inquiry, while equipping adults to host astronomy-related programs with

A report on the Indiana University Workshop on future U.S. hadron facilities

International Nuclear Information System (INIS)

Syphers, M.J.

1995-01-01

In July 1994 a workshop was held at Indiana University to study and discuss options for future hadron collider facilities in the United States, and to identify related R ampersand D programs. The workshop was conducted under the auspices of the Accelerator Physics, Technologies, and Facilities Working Group of the DPF Long Term Planning Study. Roughly 50 participants from 17 institutions in the U.S. and Europe (CERN) were organized into six working groups to study magnets, cryogenics and vacuum, antiproton sources, injectors, interaction regions, and lattice and beam dynamics. Upgrades to existing facilities (namely, Fermilab) and a post-LHC facility were discussed at the workshop. In this paper, the discussion will focus on the post-LHC facility. One of the specific goals of the workshop was to develop a defensible parameters list for a 30 TeV x 30 TeV hadron collider with luminosity of 1 x 10 34 cm -2 sec -1 . While this accelerator would have only 50% higher energy than the SSC design, it was realized that the role of synchrotron radiation at this energy would significantly enhance the design and operation of the machine. Radiation damping times of a few hours, rather than one day, can be realized thus allowing less intense, but brighter proton beams

Report of the workshop on Aviation Safety/Automation Program

Science.gov (United States)

Morello, Samuel A. (Editor)

1990-01-01

As part of NASA's responsibility to encourage and facilitate active exchange of information and ideas among members of the aviation community, an Aviation Safety/Automation workshop was organized and sponsored by the Flight Management Division of NASA Langley Research Center. The one-day workshop was held on October 10, 1989, at the Sheraton Beach Inn and Conference Center in Virginia Beach, Virginia. Participants were invited from industry, government, and universities to discuss critical questions and issues concerning the rapid introduction and utilization of advanced computer-based technology into the flight deck and air traffic controller workstation environments. The workshop was attended by approximately 30 discipline experts, automation and human factors researchers, and research and development managers. The goal of the workshop was to address major issues identified by the NASA Aviation Safety/Automation Program. Here, the results of the workshop are documented. The ideas, thoughts, and concepts were developed by the workshop participants. The findings, however, have been synthesized into a final report primarily by the NASA researchers.

Report of the workshop on realistic SSC lattices

International Nuclear Information System (INIS)

1985-10-01

A workshop was held at the SSC Central Design Group from May 29 to June 4, 1985, on topics relating to the lattice of the SSC. The workshop marked a shift of emphasis from the investigation of simplified test lattices to the development of a realistic lattice suitable for the conceptual design report. The first day of the workshop was taken up by reviews of accelerator system requirements, of the reference design solutions for these requirements, of lattice work following the reference design, and of plans for the workshop. The work was divided among four working groups. The first, chaired by David Douglas, concerned the arcs of regular cells. The second group, which studied the utility insertions, was chaired by Beat Leemann. The third group, under David E. Johnson, concerned itself with the experimental insertions, dispersion suppressors, and phase trombones. The fourth group, responsible for global lattice considerations and the design of a new realistic lattice example, was led by Ernest Courant. The papers resulting from this workshop are roughly divided into three sets: those relating to specific lattice components, to complete lattices, and to other topics. Among the salient accomplishments of the workshop were additions to and optimization of lattice components, especially those relating to lattices using 1-in-1 magnets, either horizontally or vertically separated, and the design of complete lattice examples. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

Proceedings of the first JAERI-Kansai international workshop on ultrashort-pulse ultrahigh-power lasers and simulation for laser-plasma interactions

International Nuclear Information System (INIS)

1998-03-01

Records of the First JAERI-Kansai International Workshop, which focused on the subject of 'Ultrashort-Pulse Ultrahigh-Power Lasers and Simulation for Laser-Plasma Interactions', are contained in this issue. The First JAERI-Kansai International Workshop was held as Joint ICFA/JAERI-Kansai International Workshop '97 with International Committee for Future Accelerators (ICFA). This report consists of 24 contributed papers. (J.P.N.)

Proceedings of the first JAERI-Kansai international workshop on ultrashort-pulse ultrahigh-power lasers and simulation for laser-plasma interactions

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Records of the First JAERI-Kansai International Workshop, which focused on the subject of `Ultrashort-Pulse Ultrahigh-Power Lasers and Simulation for Laser-Plasma Interactions`, are contained in this issue. The First JAERI-Kansai International Workshop was held as Joint ICFA/JAERI-Kansai International Workshop `97 with International Committee for Future Accelerators (ICFA). This report consists of 24 contributed papers. (J.P.N.)

Participatory Design of Websites with Web Design Workshops

Directory of Open Access Journals (Sweden)

Alison Bersani

2008-03-01

Full Text Available At the University of Rochester's River Campus Libraries we have included users in technology development with great success. "Participatory design" entails collaboration among designers, developers, and users from the earliest stages of conception through to implementation of websites and other technology. Using participatory methods, a project to redesign the library website began with workshops to identify user needs and preferences. The results of these workshops led to the identification of key tasks for the main page. They also generated a hierarchy of tasks for sub-pages and rich information about how students and faculty members use current websites in their work. In our article, we explain our reasons for running participatory design workshops, describe our methods, review participants and recruitment, and summarize key findings. We also include information about our local implementation and general conclusions about the value of design workshops for website design and development.

The 13th international workshop on targetry and target chemistry proceedings

Energy Technology Data Exchange (ETDEWEB)

Haroun, S. (SFU, TRIUMF (Canada)); Givskov, A.; Jensen, Mikael (Technical Univ. of Denmark. Risoe National Laboratory for Sustainable Energy, Radiation Research Division, Roskilde (Denmark))

2011-06-15

This report contains the complete proceedings of the 13th International Workshop on Targetry and Target Chemistry. The Workshop was held at Risoe National Laboratory for Sustainable Energy on July 26-28 2010. The workshop deals with the development of methods and systems for efficient production of radioactive isotopes with accelerators. The WTTC series of workshops was initiated for the purpose of exchanging information about the problems and solutions associated with the production of radioisotopes for biomedical research and their applications to the diagnosis and treatment of disease. The goal of the WTTC is to advance the science associated with radioisotope production targetry. The Workshops are designed to bring experienced targetry scientists together with newcomers to the field, both from industry and academia, to discuss issues of targetry and target chemistry and approaches to exploring in situ target chemistry and the engineering required to optimize production yields. In the workshop, experience, ideas and information are freely and openly shared; learning and collaborations are fostered, with active participation by all attendees. This participation includes both formal and informal sessions. The present proceedings captures both submitted abstracts and the actual presentations showed during the very successful workshop meeting number 13 in the row, the WTTC13. (Author)

The 13th international workshop on targetry and target chemistry proceedings

International Nuclear Information System (INIS)

Haroun, S.; Givskov, A.; Jensen, Mikael

2011-06-01

This report contains the complete proceedings of the 13th International Workshop on Targetry and Target Chemistry. The Workshop was held at Risoe National Laboratory for Sustainable Energy on July 26-28 2010. The workshop deals with the development of methods and systems for efficient production of radioactive isotopes with accelerators. The WTTC series of workshops was initiated for the purpose of exchanging information about the problems and solutions associated with the production of radioisotopes for biomedical research and their applications to the diagnosis and treatment of disease. The goal of the WTTC is to advance the science associated with radioisotope production targetry. The Workshops are designed to bring experienced targetry scientists together with newcomers to the field, both from industry and academia, to discuss issues of targetry and target chemistry and approaches to exploring in situ target chemistry and the engineering required to optimize production yields. In the workshop, experience, ideas and information are freely and openly shared; learning and collaborations are fostered, with active participation by all attendees. This participation includes both formal and informal sessions. The present proceedings captures both submitted abstracts and the actual presentations showed during the very successful workshop meeting number 13 in the row, the WTTC13. (Author)

U.S.-Japan workshop on 'RF heating and current drive in confinement systems tokamaks'

International Nuclear Information System (INIS)

1992-01-01

The workshop was attended by 8 US scientists and 30 Japanese scientists. The agenda was divided into 2 1/2 days of presentation, 1/2 day group discussions and 1/2 day summary session. There were 10 papers on rf physics, technologies and applications; 6 papers on new concepts, helicity injection and transport; and 6 papers on heating/current drive and scrape-off-layer/divertor conditions. The wide range of topics discussed is an indication of the impressive growth, both in depth and breadth, of the US-Japan workshop in RF Heating and Current Drive. It also benefitted by being combined with the new current drive concepts workshops and the active participation of JAERI scientists. (J.P.N.)

16th Workshop on High Energy Spin Physics

CERN Document Server

2016-01-01

The Workshop will cover a wide range of spin phenomena at high and intermediate energies such as: recent experimental data on spin physics the nucleon spin structure and GPD's spin physics and QCD spin physics in the Standard Model and beyond T-odd spin effects polarization and heavy ion physics spin in gravity and astrophysics the future spin physics facilities spin physics at NICA polarimeters for high energy polarized beams acceleration and storage of polarized beams the new polarization technology related subjects The Workshop will be held in the Bogoliubov Laboratory of Theoretical Physics of the Joint Institute for Nuclear Research, 141980 Dubna, Moscow Region, Russia. The program of the workshop will include plenary and parallel (if necessary) sessions. Plenary sessions will be held in the Conference Hall. Parallel sections will take place in the same building. There will be invited talks (up to 40 min) and original reports (20 min). The invited speakers will present new experimental and theoretical re...

Reduced withdrawal and failure rates of accelerated nursing students enrolled in pharmacology is associated with a supportive intervention.

Science.gov (United States)

Doggrell, Sheila Anne; Schaffer, Sally

2016-02-01

To reduce nursing shortages, accelerated nursing programs are available for domestic and international students. However, the withdrawal and failure rates from these programs may be different than for the traditional programs. The main aim of our study was to improve the retention and experience of accelerated nursing students. The academic background, age, withdrawal and failure rates of the accelerated and traditional students were determined. Data from 2009 and 2010 were collected prior to intervention. In an attempt to reduce the withdrawal of accelerated students, we set up an intervention, which was available to all students. The assessment of the intervention was a pre-post-test design with non-equivalent groups (the traditional and the accelerated students). The elements of the intervention were a) a formative website activity of some basic concepts in anatomy, physiology and pharmacology, b) a workshop addressing study skills and online resources, and c) resource lectures in anatomy/physiology and microbiology. The formative website and workshop was evaluated using questionnaires. The accelerated nursing students were five years older than the traditional students (p students, than for traditional students who have undertaken first year courses in anatomy and physiology (p = 0.04 in 2010). The withdrawing students were predominantly the domestic students with non-university qualifications or equivalent experience. The failure rates were also higher for this group, compared to the traditional students (p = 0.05 in 2009 and 0.03 in 2010). In contrast, the withdrawal rates for the international and domestic graduate accelerated students were very low. After the intervention, the withdrawal and failure rates in pharmacology for domestic accelerated students with non-university qualifications were not significantly different than those of traditional students. The accelerated international and domestic graduate nursing students have low withdrawal

Proceedings of the workshop on experiments and experimental facilities at SIS/ESR

International Nuclear Information System (INIS)

1987-04-01

The present proceedings contain the abstracts of the proposals and letters of intent prepared by the authors for general distribution. The abstracts are organized according to the sessions in which they were presented at the workshop. The program of the workshop is also included as is the list of attendees. In addition we have included two recent descriptions of the accelerator facilities providing information on the latest status of the expected beam schedule for SIS and performance characteristics of the ESR. (orig./HSI)

The intense proton accelerator program

International Nuclear Information System (INIS)

Kaneko, Yoshihiko

1990-01-01

The Science and Technology Agency of Japan has formulated the OMEGA project, in which incineration of nuclear wastes by use of accelerators is defined as one of the important tasks. Japan Atomic Energy Research Institute (JAERI) has been engaged for several years in basic studies in incineration technology with use of an intense proton linear accelerator. The intense proton accelerator program intends to provide a large scale proton linear accelerator called Engineering Test Accelerator. The principal purpose of the accelerator is to develop nuclear waste incineration technology. The accelerator will also be used for other industrial applications and applied science studies. The present report further outlines the concept of incineration of radio-activities of nuclear wastes, focusing on nuclear reactions and a concept of incineration plant. Features of Engineering Test Accelerator are described focusing on the development of the accelerator, and research and development of incineration technology. Applications of science and technology other than nuclear waste incineration are also discussed. (N.K.)

Requirements of a proton beam accelerator for an accelerator-driven reactor

International Nuclear Information System (INIS)

Takahashi, H.; Zhao, Y.; Tsoupas, N.; An, Y.; Yamazaki, Y.

1997-01-01

When the authors first proposed an accelerator-driven reactor, the concept was opposed by physicists who had earlier used the accelerator for their physics experiments. This opposition arose because they had nuisance experiences in that the accelerator was not reliable, and very often disrupted their work as the accelerator shut down due to electric tripping. This paper discusses the requirements for the proton beam accelerator. It addresses how to solve the tripping problem and how to shape the proton beam

Japanese contributions to IAEA INTOR Workshop, phase IIA

International Nuclear Information System (INIS)

Tomabechi, Ken; Hiraoka, Tohru; Fujisawa, Noboru; Nishio, Satoshi; Sawada, Yoshio; Kobayashi, Takeshi.

1982-11-01

Japanese contributions at INTOR Phase 2A are summarized as a first three chapters of the report, Japanese Contributions to INTOR Workshop, Phase 2A. This report contains Introduction, Summary of the total report and INTOR Concepts. (author)

Heat pipe applications workshop report

International Nuclear Information System (INIS)

Ranken, W.A.

1978-04-01

The proceedings of the Heat Pipe Applications Workshop, held at the Los Alamos Scientific Laboratory October 20-21, 1977, are reported. This workshop, which brought together representatives of the Department of Energy and of a dozen industrial organizations actively engaged in the development and marketing of heat pipe equipment, was convened for the purpose of defining ways of accelerating the development and application of heat pipe technology. Recommendations from the three study groups formed by the participants are presented. These deal with such subjects as: (1) the problem encountered in obtaining support for the development of broadly applicable technologies, (2) the need for applications studies, (3) the establishment of a heat pipe technology center of excellence, (4) the role the Department of Energy might take with regard to heat pipe development and application, and (5) coordination of heat pipe industry efforts to raise the general level of understanding and acceptance of heat pipe solutions to heat control and transfer problems

A beam-matching concept for medical linear accelerators

DEFF Research Database (Denmark)

Sjöström, David; Bjelkengren, Ulf; Ottosson, Wiviann

2009-01-01

The flexibility in radiotherapy can be improved if a patient can be moved between any one of the department's medical linear accelerators without the need to change anything in the patient's treatment plan. For this to be possible, the dosimetric characteristics of the various accelerators must...

Workshop on materials control and accounting system design

International Nuclear Information System (INIS)

Pillay, K.K.S.

1989-01-01

The chapter describes the workshop aimed at reinforcing, through participation in the design exercise, the concepts of nuclear materials control and accountability. Topics include: workshop format; key elements of a materials management and accounting (MC and A) system; and MC and A system design including safeguards organization and management, material access areas, key measurement points, nuclear materials measurements, physical inventory, material balance closings, and internal controls. Appended to this chapter is a detailed description of a facility that produces metallic plutonium and the safeguards requirements for this facility

Laser wakefield accelerator based light sources: potential applications and requirements

Energy Technology Data Exchange (ETDEWEB)

Albert, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). NIF and Photon Sciences; Thomas, A. G. [Univ. of Michigan, Ann Arbor, MI (United States). Dept. of Nuclear Engineering and Radiological Sciences; Mangles, S. P.D. [Imperial College, London (United Kingdom). Blackett Lab.; Banerjee, S. [Univ. of Nebraska, Lincoln, NE (United States); Corde, S. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Flacco, A. [ENSTA, CNRS, Ecole Polytechnique, Palaiseau (France); Litos, M. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Neely, D. [Science and Technology Facilities Council (STFC), Oxford (United Kingdom). Rutherford Appleton Lab. (RAL). Central Laser Facility; Viera, J. [Univ. of Lisbon (Portugal). GoLP-Inst. de Plasmas e Fusao Nuclear-Lab. Associado; Najmudin, Z. [Imperial College, London (United Kingdom). Blackett Lab.; Bingham, R. [Science and Technology Facilities Council (STFC), Oxford (United Kingdom). Rutherford Appleton Lab. (RAL). Central Laser Facility; Joshi, C. [Univ. of California, Los Angeles, CA (United States). Dept. of Electrical Engineering; Katsouleas, T. [Duke Univ., Durham, NC (United States). Platt School of Engineering

2015-01-15

In this article we review the prospects of laser wakefield accelerators as next generation light sources for applications. This work arose as a result of discussions held at the 2013 Laser Plasma Accelerators Workshop. X-ray phase contrast imaging, X-ray absorption spectroscopy, and nuclear resonance fluorescence are highlighted as potential applications for laser-plasma based light sources. We discuss ongoing and future efforts to improve the properties of radiation from plasma betatron emission and Compton scattering using laser wakefield accelerators for these specific applications.

Workshop on rules for exemption from regulatory control: Proceedings

International Nuclear Information System (INIS)

1989-04-01

This conference report documents the proceedings of an International Workshop on the subject of exempting radiation sources and practices from regulatory control. The purpose of the workshop was to provide national regulatory authorities an opportunity to exchange information on their respective approaches and practices involving exemptions and to enhance international understanding and cooperation on the derivation and practical application of the underlying principles. In addition, input from the workshop was intended to assist the NRC in the development of a policy statement on this issue. The workshop was divided into five sessions. During the first four sessions, papers were presented which defined the relative terms and concepts, outlined the national situations and approaches to the establishment and development of exemption rules, identified and discussed the existing issues, and gave the status of the international guidelines on exemption rules. The fifth session was devoted to summarizing the workshop and identifying the areas of consensus, the outstanding issues and the areas for future work. Individual papers were processed separately for the data base

Final technical report. 1998 HU CFRT summer fusion high school workshop

International Nuclear Information System (INIS)

Ali, Halima; Punjabi, Alkesh

1999-01-01

The center conducted its third High School Summer Fusion Science Workshop in Summer 1998. The center had only three faculty mentors available only for a part of Summer 1998, The center accepted four scholars in this workshop, Prof. Halima Ali coordinated this workshop. Each student was assigned to a research mentor according to the student's interest in a specific research area and problem. In the workshop in the center, the students received instructions and training in the basics of energy, plasma and fusion sciences. They also received one-on-one instructions and training by their mentors to further their understanding of the subject and to introduce to relevant concepts such as magnetic confinement fusion, tokamaks, diverters and area-preserving maps

Overview and charge - Snowmass Workshop 2005

International Nuclear Information System (INIS)

Berger, E. L.

2006-01-01

This contribution to the published Proceedings records the opening talk I presented on the first morning of the 2005 International Linear Collider Workshop in Snowmass, CO, August 14 - 27, 2005. It includes a summary of the motivation for the workshop, the scientific goals and charges for the working groups, the initial plans of the accelerator, detector, and physics groups, and the activities of the communication, education, and outreach group. This document also describes organizational aspects of the meeting, particularly the scientific committee structure, the self-organization of the working groups, the composition of the indispensable secretariat and computer support teams, and the sources of funding support. The report serves as an introduction to the proceedings whose individual papers and summary documents must be consulted for an appreciation of the accomplishments and progress made at Snowmass in 2005 toward the realization of an International Linear Collider

ECETOC Florence workshop on risk assessment of endocrine substances, including the potency concept.

Science.gov (United States)

Fegert, Ivana

2013-12-16

The European regulation on plant protection products (1107/2009) and the Biocidal Products Regulation (EC Regulation 528/2012) only support the marketing and use of chemicals if they do not cause endocrine disruption in humans or wildlife species. Also, substances with endocrine properties are subject to authorization under the European regulation on the registration, evaluation, authorization and restriction of chemicals (REACH; 1907/2006). Therefore, the regulatory consequences of identifying a substance as an endocrine disrupting chemical are severe. In contrast to that, basic scientific criteria, necessary to define endocrine disrupting properties, are not described in any of these legislative documents. Thus, the European Center for Ecotoxicology and Toxicology of Chemicals (ECETOC) established a task force to provide scientific criteria for the identification and assessment of chemicals with endocrine disrupting properties that may be used within the context of these three legislative texts (ECETOC, 2009a). In 2009, ECETOC introduced a scientific framework as a possible concept for identifying endocrine disrupting properties within a regulatory context (ECETOC, 2009b; Bars et al., 2011a,b). The proposed scientific criteria integrated, in a weight of evidence approach, information from regulatory (eco)toxicity studies and mechanistic/screening studies by combining evidence for adverse effects detected in apical whole-organism studies with an understanding of the mode of action (MoA) of endocrine toxicity. However, since not all chemicals with endocrine disrupting properties are of equal hazard, an adequate concept should also be able to differentiate between chemicals with endocrine properties of low concern from those of higher concern (for regulatory purposes). For this purpose, the task force refined this part of their concept. Following an investigation of the key factors at a second workshop of invited regulatory, academic and industry scientists, the

Proceedings of the workshops on 'JAEA project researches at J-PARC/MLF'

International Nuclear Information System (INIS)

Kajimoto, Ryoichi; Maekawa, Fujio; Arima, Hiroshi; Yoshinari, Shizuka; Arai, Masatoshi

2011-06-01

The operation for public use of Materials and Life Science Experimental Facility (MLF) at Japan Proton Accelerator Research Complex (J-PARC) has started since the end of 2008. Rather stable neutron and muon beams at 120 kW are being supplied throughout 2010. Some of the instruments have already produced several good scientific outputs. Furthermore, operation at 200 kW, which exceeds the beam power of the ISIS facility in UK, has started since December 2010. In this promising situation for MLF, we hold three workshops for five neutron instruments which conducted researches for projects by Japan Atomic Energy Agency (JAEA) (project researches): 'Workshop on BL19 (Sep. 29)', 'Workshop on BL04+BL10 (Oct. 28)', and 'Workshop on BL01+BL14 (Oct. 29)'. There, status of the instruments and recent results of the project researches as well as a part of researches by general users were reported, and future directions and issues to be solved of the researches were discussed. This report includes abstracts, materials of the presentations and summary of discussions in the workshops. (author)

Proceedings of the first international workshop on accelerator alignment

Energy Technology Data Exchange (ETDEWEB)

1990-10-01

This report contains papers on the following accelerator topics: current alignment topics; toolboxes: instrumentation, software, and methods; fiducialization of conventional magnets; fiducialization of superconducting magnets; and next generation linear colliders.

Virtual accelerator concept, implementation and preliminary test; Accelerateur virtuel Concept, implementation et premier test

Energy Technology Data Exchange (ETDEWEB)

Uriot, D.; Duperrier, R

2006-05-15

A virtual accelerator is the coupling of a simulation code with the control system of a real machine. 3 operating modes are considered. First, the monitoring mode in which any action on the control system has an impact on both real and virtual machines. This mode allows a direct comparison between simulation results and the real behaviour of the accelerator. Secondly, the flight simulation mode, this mode allows the accelerator operators to simulate the effect of any change in the parameters of the control system before transferring them to the real machine. The main advantage of this mode is to allow the assessment of operating procedures before implementing them on the real machine. The third mode is the automatic steering mode in which the simulation code assumes the reins of the control system of the real machine. This mode allows the making of complex and time-consuming adjustment procedures in an automatic way. TraceWin is a simulation code dedicated to the behaviour of charged-particle beams in a linear accelerator. TraceWin is consistent with the EPICS technology on which the control system of most accelerators is based. A virtual accelerator composed of the SILHI injector combined to the TraceWin code via the EPICS environment has showed its efficiency in the automatic steering mode. (A.C.)

Faculty Development for Small-Group-Teaching with Simulated Patients (SP) - Design and Evaluation of a Competency-based Workshop.

Science.gov (United States)

Hölzer, Henrike; Freytag, Julia; Sonntag, Ulrike

2017-01-01

Objective: The introduction of innovative teaching formats and methods in medical education requires a specific didactic training for teachers to use complicated formats effectively. This paper describes preliminary considerations, design, implementation and evaluation of a skills-based workshop (7,5 hours long) for teaching with simulated patients. The aim is to describe the essential components for a lasting effect of the workshop so that the concept can be adapted to other contexts. Method: We present the theoretical framework, the objectives, the didactic methodology and the implementation of the workshop. The evaluation of the workshop was carried out using questionnaires. First the participants (teachers of the faculty of medicine, clinical and science subjects) were asked to estimate how well they felt prepared for small group teaching immediately after workshop. Later, after some teaching experience of their own, they gave feedback again as a part of the general evaluation of the semester. Results: In the course of three years 27 trainings were conducted and evaluated with a total of 275 participants. In the context of semester evaluation 452 questionnaires were evaluated on the quality of training. Conclusion: The evaluation shows that participants appreciate the concept of the workshop and also feel sufficiently well prepared. As a limitation it must be said that this is so far only the lecturers' self-assessment. Nevertheless, it can be stated that even a one-day workshop with a stringent teaching concept shows long term results regarding innovative teaching methods.

Summary of Working Group 7 on 'Exotic acceleration schemes'

International Nuclear Information System (INIS)

Tajima, T.

2001-01-01

Exotic concepts of advanced acceleration technologies have been explored by Group 7 under the leadership of T. Tajima and T. Smith (who could not attend) at the AAC. Explored concepts are: (1) proton (ion) acceleration by laser, (2) additional ion acceleration methods, (3) crystal x-rays and acceleration, (4) vacuum acceleration, (5) active medium acceleration, and (6) some advanced methods in laser wakefield. The first subject of laser photon acceleration was discussed jointly with Group 1 and in the end the participants came to an agreement on the mechanism of proton acceleration by laser irradiation

Rule based design workshop at the TU Berlin

DEFF Research Database (Denmark)

Tamke, Martin; Palz, Norbert; Josefsson, Kristoffer

and design concepts to lead into a second workshop further exploring digital design and fabrication tools. The goal is to produce a full-scale prototype to test the ideas, methods and materials. This paper focuses on digital design & fabrication via a pedagogical exploration between academics...

Laser technology inspires new accelerator concepts

CERN Multimedia

Katarina Anthony

2012-01-01

A new EU-funded research network, LA³NET, is bringing together universities, research centres and industry partners worldwide to explore the use of laser technology in particle beam generation, acceleration and diagnostics. As one of the network partners, CERN will be hosting three early stage researchers in the BE and EN Departments.   One of the laser systems now in use in the ISOLDE experiment. If you take a closer look at recent experimental developments, you’ll notice a new topic trending: laser technology. It’s being used to study the characteristics of particles, as incorporated into the new ALPHA-2 set-up; to conduct diagnostics of particle beams, as used in a laser wire scanner at Petra III; to “breed” unusual ion beams, as carried out by ISOLDE’s Resonance Ionization Laser Ion Source (RILIS); and even to accelerate particles to high energies, as explored at Berkeley’s BELLA facility. These projects notwithstanding...

ISC High Performance 2016 International Workshops, ExaComm, E-MuCoCoS, HPC-IODC, IXPUG, IWOPH, P^3MA, VHPC, WOPSSS

CERN Document Server

Mohr, Bernd; Kunkel, Julian M

2016-01-01

This book constitutes revised selected papers from 7 workshops that were held in conjunction with the ISC High Performance 2016 conference in Frankfurt, Germany, in June 2016. The 45 papers presented in this volume were carefully reviewed and selected for inclusion in this book. They stem from the following workshops: Workshop on Exascale Multi/Many Core Computing Systems, E-MuCoCoS; Second International Workshop on Communication Architectures at Extreme Scale, ExaComm; HPC I/O in the Data Center Workshop, HPC-IODC; International Workshop on OpenPOWER for HPC, IWOPH; Workshop on the Application Performance on Intel Xeon Phi – Being Prepared for KNL and Beyond, IXPUG; Workshop on Performance and Scalability of Storage Systems, WOPSSS; and International Workshop on Performance Portable Programming Models for Accelerators, P3MA.

Centripetal Acceleration: Often Forgotten or Misinterpreted

Science.gov (United States)

Singh, Chandralekha

2009-01-01

Acceleration is a fundamental concept in physics which is taught in mechanics at all levels. Here, we discuss some challenges in teaching this concept effectively when the path along which the object is moving has a curvature and centripetal acceleration is present. We discuss examples illustrating that both physics teachers and students have…

Lunar Reconnaissance Orbiter Lunar Workshops for Educators, Year 1 Report

Science.gov (United States)

Jones, A. P.; Hsu, B. C.; Bleacher, L.; Shaner, A. J.; Dalton, H.

2011-12-01

This past summer, the Lunar Reconnaissance Orbiter (LRO) sponsored a series of weeklong professional development workshops designed to educate and inspire grade 6-12 science teachers: the Lunar Workshops for Educators. Participants learned about lunar science and exploration, gained tools to help address common student misconceptions about the Moon, heard some of the latest research results from LRO scientists, worked with LRO data, and learned how to bring these data to their students using hands-on activities aligned with grade 6-12 National Science Education Standards and Benchmarks. Where possible, the workshops also included tours of science facilities or field trips intended to help the teachers better understand mission operations or geologic processes relevant to the Moon. The workshops were very successful. Participants demonstrated an improved understanding of lunar science concepts in post-workshop assessments (as compared to identical pre-assessments) and a greater understanding of how to access and productively share data from LRO with their students and provide them with authentic research experiences. Participant feedback on workshop surveys was also enthusiastically positive. 5 additional Lunar Workshops for Educators will be held around the country in the summer of 2012. For more information and to register, visit http://lunar.gsfc.nasa.gov/lwe/index.html.

Accelerating networks

International Nuclear Information System (INIS)

Smith, David M D; Onnela, Jukka-Pekka; Johnson, Neil F

2007-01-01

Evolving out-of-equilibrium networks have been under intense scrutiny recently. In many real-world settings the number of links added per new node is not constant but depends on the time at which the node is introduced in the system. This simple idea gives rise to the concept of accelerating networks, for which we review an existing definition and-after finding it somewhat constrictive-offer a new definition. The new definition provided here views network acceleration as a time dependent property of a given system as opposed to being a property of the specific algorithm applied to grow the network. The definition also covers both unweighted and weighted networks. As time-stamped network data becomes increasingly available, the proposed measures may be easily applied to such empirical datasets. As a simple case study we apply the concepts to study the evolution of three different instances of Wikipedia, namely, those in English, German, and Japanese, and find that the networks undergo different acceleration regimes in their evolution

Proceedings of the 2005 International Linear Collider Workshop (LCWS05)

International Nuclear Information System (INIS)

Hewett, JoAnne; SLAC

2006-01-01

Exploration of physics at the TeV scale holds the promise of addressing some of our most basic questions about the nature of matter, space, time, and energy. Discoveries of the Electroweak Symmetry Breaking mechanism, Supersymmetry, Extra Dimensions of space, Dark Matter particles, and new forces of nature are all possible. We have been waiting and planning for this exploration for over 20 years. In 2007 the Large Hadron Collider at CERN will begin its operation and will break into this new energy frontier. A new era of understanding will emerge as the LHC data maps out the Terascale. With the LHC discoveries, new compelling questions will arise. Responding to these questions will call for a new tool with greater sensitivity--the International Linear Collider. Historically, the most striking progress in the exploration of new energy frontiers has been made from combining results from hadron and electron-positron colliders. The precision measurements possible at the ILC will reveal the underlying theory which gave rise to the particles discovered at the LHC and will open the window to even higher energies. The world High Energy Physics community has reached an accord that an e+e- linear collider operating at 0.5-1.0 TeV would provide both unique and essential scientific opportunities; the community has endorsed with highest priority the construction of such a machine. A major milestone toward this goal was reached in August 2004 when the International Committee on Future Accelerators approved a recommendation for the technology of the future International Linear Collider. A global research and design effort is now underway to construct a global design report for the ILC. This endeavor is directed by Barry Barrish of the California Institute of Technology. The offer, made by Jonathan Dorfan on the behalf of ICFA, and acceptance of this directorship took place during the opening plenary session of this workshop. The 2005 International Linear Collider Workshop was held

Compact multi-energy electron linear accelerators

International Nuclear Information System (INIS)

Tanabe, E.; Hamm, R.W.

1985-01-01

Two distinctly different concepts that have been developed for compact multi-energy, single-section, standing-wave electron linear accelerator structures are presented. These new concepts, which utilize (a) variable nearest neighbor couplings and (b) accelerating field phase switching, provide the capability of continuously varying the electron output energy from the accelerator without degrading the energy spectrum. These techniques also provide the means for continuously varying the energy spectrum while maintaining a given average electron energy, and have been tested successfully with several accelerators of length from 0.1 m to 1.9 m. Theoretical amd experimental results from these accelerators, and demonstrated applications of these techniques to medical and industrial linear accelerator technology will be described. In addition, possible new applications available to research and industry from these techniques are presented. (orig.)

Advanced Wind Turbine Drivetrain Concepts: Workshop Report, June 29-30, 2010

Energy Technology Data Exchange (ETDEWEB)

DOE, EERE

2010-12-01

This report presents key findings from the Department of Energy's Advanced Drivetrain Workshop, held on June 29-30, 2010 in Broomfield, Colorado, to assess different advanced drivetrain technologies, their relative potential to improve the state-of-the-art in wind turbine drivetrains, and the scope of research and development needed for their commercialization in wind turbine applications.

Urban-architectural workshop as an opportunity for theoretical reflection: Example of the international urban-architectural workshop Maribor-South

Directory of Open Access Journals (Sweden)

Peter Šenk

2013-07-01

Full Text Available The paper presents the international urban-architectural workshop Maribor-South (2010-11 as a model for “Maribor’s” urban-architectural workshops, which urban planners evaluate and use to direct urban development and theoretical discussion. The presented interdisciplinary project explored possibilities for designing the southern edge of the city in the area where the southern bypass construction is planned. In addition describing the example of the workshop, which develops the theoretical field through a “practical and project approach” with the defined project basis, i.e. the defined area of discussion and project issue, the paper also highlights the opportunity for a “theoretical approach”. The theoretical approach aims at providing a wider insight into the related theoretical field based on a generalised spatial issue. As one of the key priorities of contemporary urban planning and sustainable urban redevelopment, the planned direction of urban development in the areas of constructing transport infrastructure, which is evident in the first approach, moves into a wider referential field (no longer directly related to the project with the second approach by examining the issues of mobility, space, place, diversity of infrastructures of contemporary space, etc. While in the first approach developing design concepts strives for theoretical conceptualisation, the second approach facilitates focusing on finding links between the theoretical concept and manifestations in real space, though the approaches are always separated. Their operationality is possible only on the level of “combinatorial thinking” and remains beyond direct instrumentality.

Proceedings of RIKEN BNL Research Center workshop on RHIC spin

International Nuclear Information System (INIS)

Soffer, J.

1999-01-01

This RHIC Spin Workshop is the 1999 annual meeting of the RHIC Spin Collaboration, and the second to be hosted at Brookhaven and sponsored by the RIKEN BNL Research Center. The previous meetings were at Brookhaven (1998), Marseille (1996), MIT in 1995, Argonne 1994, Tucson in 1991, and the Polarized Collider Workshop at Penn State in 1990. As noted last year, the Center provides a home for combined work on spin by theorists, experimenters, and accelerator physicists. This proceedings, as last year, is a compilation of 1 page summaries and 5 selected transparencies for each speaker. It is designed to be available soon after the workshop is completed. Speakers are welcome to include web or other references for additional material. The RHIC spin program and RHIC are rapidly becoming reality. RHIC has completed its first commissioning run, as described here by Steve Peggs. The first Siberian Snake for spin has been completed and is being installed in RHIC. A new polarized source from KEK and Triumf with over 1 milliampere of polarized H minus is being installed, described by Anatoli Zelenski. They have had a successful test of a new polarimeter for RHIC, described by Kazu Kurita and Haixin Huang. Spin commissioning is expected next spring (2000), and the first physics run for spin is anticipated for spring 2001. The purpose of the workshop is to get everyone together about once per year and discuss goals of the spin program, progress, problems, and new ideas. They also have many separate regular forums on spin. There are spin discussion sessions every Tuesday, now organized by Naohito Saito and Werner Vogelsang. The spin discussion schedule and copies of presentations are posted on http://riksg01.rhic.bnl.gov/rsc. Speakers and other spinners are encouraged to come to BNL and to lead a discussion on your favorite idea. They also have regular polarimeter and snake meetings on alternate Thursdays, led by Bill McGahern, the lead engineer for the accelerator spin effort

An Adiabatic Phase-Matching Accelerator

Energy Technology Data Exchange (ETDEWEB)

Lemery, Francois [DESY; Floettmann, Klaus [DESY; Piot, Philippe [Northern Illinois U.; Kaertner, Franz X. [Hamburg U.; Assmann, Ralph [DESY

2017-12-22

We present a general concept to accelerate non-relativistic charged particles. Our concept employs an adiabatically-tapered dielectric-lined waveguide which supports accelerating phase velocities for synchronous acceleration. We propose an ansatz for the transient field equations, show it satisfies Maxwell's equations under an adiabatic approximation and find excellent agreement with a finite-difference time-domain computer simulation. The fields were implemented into the particle-tracking program {\\sc astra} and we present beam dynamics results for an accelerating field with a 1-mm-wavelength and peak electric field of 100~MV/m. The numerical simulations indicate that a $\\sim 200$-keV electron beam can be accelerated to an energy of $\\sim10$~MeV over $\\sim 10$~cm. The novel scheme is also found to form electron beams with parameters of interest to a wide range of applications including, e.g., future advanced accelerators, and ultra-fast electron diffraction.

Results from a workshop on research needs for modeling aquifer thermal energy storage systems

Science.gov (United States)

Drost, M. K.

1990-08-01

A workshop an aquifer thermal energy storage (ATES) system modeling was conducted by Pacific Northwest Laboratory (PNL). The goal of the workshop was to develop a list of high priority research activities that would facilitate the commercial success of ATES. During the workshop, participants reviewed currently available modeling tools for ATES systems and produced a list of significant issues related to modeling ATES systems. Participants assigned a priority to each issue on the list by voting and developed a list of research needs for each of four high-priority research areas; the need for a feasibility study model, the need for engineering design models, the need for aquifer characterization, and the need for an economic model. The workshop participants concluded that ATES commercialization can be accelerated by aggressive development of ATES modeling tools and made specific recommendations for that development.

Seeking the Tricorder: Report on Workshops on Advanced Technologies for Life Detection

Science.gov (United States)

Reiss-Bubenheim, D.; Boston, P. J.; Partridge, H.; Lindensmith, C.; Nadeau, J. L.

2017-12-01

There's great excitement about life prospects on icy fluid-containing moons orbiting our Solar System's gas giant planets, newly discovered planet candidates and continuing long-term interest in possible Mars life. The astrobiology/planetary research communities require advanced technologies to explore and study both Solar System bodies and exoplanets for evidence of life. The Tricorder Workshop, held at Ames Research Center May 19-20, 2017, explored technology topics focused on non-invasive or minimally invasive methods for life detection. The workshop goal was to tease out promising ideas for low TRL concepts for advanced life detection technologies that could be applied to the surface and near-subsurface of Mars and Ocean Worlds (such as Europa and Enceladus) dominated by icy terrain. The workshop technology focus centered on mid-to-far term instrument concepts or other enabling technologies (e.g. robotics, machine learning, etc.) primarily for landed missions, which could detect evidence of extant, extinct and/or "weird" life including the notion of "universal biosignatures". Emphasis was placed on simultaneous and serial sample measurements using a suite of instruments and technological approaches with planetary protection in mind. A follow-on workshop, held July 24 at Caltech, sought to develop a generic flowchart of in situ observations and measurements to provide sufficient information to determine if extant life is present in an environment. The process didn't require participant agreement as to definition of extant life, but instead developed agreement on necessary observations and instruments. The flowchart of measurements was designed to maximize the number of simultaneous observations on a single sample where possible, serializing where necessary, and finally dividing it into parts for the most destructive analyses at the end. Selected concepts from the workshops outlined in this poster provide those technology areas necessary to solicit and develop

Participants of the LLRF05 : Workshop on Low Level RF, CERN 10-13 October 2005

CERN Multimedia

Maximilien Brice

2005-01-01

Sophisticated Low Level RF systems are needed in modern particle accelerators to deal with the characteristics of state-of-the-art RF accelerating structures and their power sources, and to meet unprecedented levels of performance. The goal of the LLRF05 workshop is to share experience between linac and synchrotron projects (SNS, J-PARC, ILC, LHC etc.) and to discuss the best engineering practice.

Nuclear physics workshop

International Nuclear Information System (INIS)

1988-01-01

This Workshop in Nuclear Physics related to the TANDAR, took place in Buenos Aires in April from 23 to 26, 1987, with attendance of foreign scientists. There were presented four seminars and a lot of studies which deal with the following fields: Nuclear Physics at medium energies, Nuclear Structure, Nuclear Reactions, Nuclear Matter, Instrumentation and Methodology for Nuclear Spectroscopy, Classical Physics, Quantum Mechanics and Field Theory. It must be emphasized that the Electrostatic Accelerator TANDAR allows to work with heavy ions of high energy, that opens a new field of work in PIXE (particle induced X-ray emission). This powerful analytic technique makes it possiblethe analysis of nearly all the elements of the periodic table with the same accuracy. (M.E.L.) [es

Report of the fifth workshop on synchrotron x-ray lithography

International Nuclear Information System (INIS)

Williams, G.P.; Godel, J.B.; Brown, G.S.

1989-01-01

Semiconductors comprise a greater part of the United States economy than the aircraft, steel and automobile industries combined. In future the semiconductor manufacturing industry will be forced to switch away from present optical manufacturing methods in the early to mid 1990's. X-ray lithography has emerged as the leading contender for continuing production below the 0.4 micron level. Brookhaven National Laboratory began a series of workshops on x-ray lithography in 1986 to examine key issues and in particular to enable United States industry to take advantage of the technical base established in this field. Since accelerators provide the brightest sources for x-ray lithography, most of the research and development to date has taken place at large accelerator-based research centers such as Brookhaven, the University of Wisconsin and Stanford. The goals of this Fifth Brookhaven Workshop were to review progress and goals since the last workshop and to establish a blueprint for the future. The meeting focused on the ''Exposure Tool,'' that is, a term defined as the source plus beamline and stepper. In order to assess the appropriateness of schedules for the development of this tool, other aspects of the required technology such as masks, resists and inspection and repair were also reviewed. To accomplish this, two working groups were set up, one to review the overall aspects of x-ray lithography and set a time frame, the other to focus on sources

Report of the fifth workshop on synchrotron x-ray lithography

Energy Technology Data Exchange (ETDEWEB)

Williams, G.P.; Godel, J.B. (Brookhaven National Lab., Upton, NY (USA)); Brown, G.S. (Stanford Univ., CA (USA). Stanford Synchrotron Radiation Lab.); Liebmann, W. (Suss (Karl) America, Essex Junction, VT (USA))

1989-01-01

Semiconductors comprise a greater part of the United States economy than the aircraft, steel and automobile industries combined. In future the semiconductor manufacturing industry will be forced to switch away from present optical manufacturing methods in the early to mid 1990's. X-ray lithography has emerged as the leading contender for continuing production below the 0.4 micron level. Brookhaven National Laboratory began a series of workshops on x-ray lithography in 1986 to examine key issues and in particular to enable United States industry to take advantage of the technical base established in this field. Since accelerators provide the brightest sources for x-ray lithography, most of the research and development to date has taken place at large accelerator-based research centers such as Brookhaven, the University of Wisconsin and Stanford. The goals of this Fifth Brookhaven Workshop were to review progress and goals since the last workshop and to establish a blueprint for the future. The meeting focused on the Exposure Tool,'' that is, a term defined as the source plus beamline and stepper. In order to assess the appropriateness of schedules for the development of this tool, other aspects of the required technology such as masks, resists and inspection and repair were also reviewed. To accomplish this, two working groups were set up, one to review the overall aspects of x-ray lithography and set a time frame, the other to focus on sources.

Report on the fifth workshop on synchrotron x ray lithography

Science.gov (United States)

Williams, G. P.; Godel, J. B.; Brown, G. S.; Liebmann, W.

Semiconductors comprise a greater part of the United States economy than the aircraft, steel, and automobile industries combined. In future the semiconductor manufacturing industry will be forced to switch away from present optical manufacturing methods in the early to mid 1990s. X ray lithography has emerged as the leading contender for continuing production below the 0.4 micron level. Brookhaven National Laboratory began a series of workshops on x ray lithography in 1986 to examine key issues and in particular to enable United States industry to take advantage of the technical base established in this field. Since accelerators provide the brightest sources for x ray lithography, most of the research and development to date has taken place at large accelerator-based research centers such as Brookhaven, the University of Wisconsin, and Stanford. The goals of this Fifth Brookhaven Workshop were to review progress and goals since the last workshop and to establish a blueprint for the future. The meeting focused on the exposure tool, that is, a term defined as the source plus beamline and stepper. In order to assess the appropriateness of schedules for the development of this tool, other aspects of the required technology such as masks, resists and inspection and repair were also reviewed. To accomplish this, two working groups were set up, one to review the overall aspects of x ray lithography and set a time frame, the other to focus on sources.

Materials characterization center workshop on corrosion of engineered barriers

Energy Technology Data Exchange (ETDEWEB)

Merz, M.D.; Zima, G.E.; Jones, R.H.; Westerman, R.E.

1981-03-01

A workshop on corrosion test procedures for materials to be used as barriers in nuclear waste repositories was conducted August 19 and 20, 1980, at the Battelle Seattle Research Center. The purpose of the meeting was to obtain guidance for the Materials Characterization Center in preparing test procedures to be approved by the Materials Review Board. The workshop identified test procedures that address failure modes of uniform corrosion, pitting and crevice corrosion, stress corrosion, and hydrogen effects that can cause delayed failures. The principal areas that will require further consideration beyond current engineering practices involve the analyses of pitting, crevice corrosion, and stress corrosion, especially with respect to quantitative predictions of the lifetime of barriers. Special techniques involving accelerated corrosion testing for uniform attack will require development.

Materials characterization center workshop on corrosion of engineered barriers

International Nuclear Information System (INIS)

Merz, M.D.; Zima, G.E.; Jones, R.H.; Westerman, R.E.

1981-03-01

A workshop on corrosion test procedures for materials to be used as barriers in nuclear waste repositories was conducted August 19 and 20, 1980, at the Battelle Seattle Research Center. The purpose of the meeting was to obtain guidance for the Materials Characterization Center in preparing test procedures to be approved by the Materials Review Board. The workshop identified test procedures that address failure modes of uniform corrosion, pitting and crevice corrosion, stress corrosion, and hydrogen effects that can cause delayed failures. The principal areas that will require further consideration beyond current engineering practices involve the analyses of pitting, crevice corrosion, and stress corrosion, especially with respect to quantitative predictions of the lifetime of barriers. Special techniques involving accelerated corrosion testing for uniform attack will require development

A workshop on asthma management programs and centers in Brazil: reviewing and explaining concepts*

Science.gov (United States)

Stelmach, Rafael; Neto, Alcindo Cerci; Fonseca, Ana Cristina de Carvalho Fernandez; Ponte, Eduardo Vieira; Alves, Gerardo; Araujo-Costa, Ildely Niedia; Lasmar, Laura Maria de Lima Belizário Facury; de Castro, Luci Keiko Kuromoto; Lenz, Maria Lucia Medeiros; Silva, Paulo; Cukier, Alberto; Alves, Alexssandra Maia; Lima-Matos, Aline Silva; Cardoso, Amanda da Rocha Oliveira; Fernandes, Ana Luisa Godoy; de São-José, Bruno Piassi; Riedi, Carlos Antônio; Schor, Deborah; Peixoto, Décio Medeiros; Brandenburg, Diego Djones; Camillo, Elineide Gomes dos Santos; Serpa, Faradiba Sarquis; Brandão, Heli Vieira; Lima, João Antonio Bonfadini; Pio, Jorge Eduardo; Fiterman, Jussara; Anderson, Maria de Fátima; Cardoso, Maria do Socorro de Lucena; Rodrigues, Marcelo Tadday; Pereira, Marilyn Nilda Esther Urrutia; Antila, Marti; Martins, Sonia Maria; Guimarães, Vanessa Gonzaga Tavares; Mello, Yara Arruda Marques; de Andrade, Wenderson Clay Correia; Salibe-Filho, William; Caldeira, Zelina Maria da Rocha; da Cruz-Filho, Álvaro Augusto Souza; Camargos, Paulo

2015-01-01

Objective: To report the results of a workshop regarding asthma management programs and centers (AMPCs) in Brazil, so that they can be used as a tool for the improvement and advancement of current and future AMPCs. Methods: The workshop consisted of five presentations and the corresponding group discussions. The working groups discussed the following themes: implementation of asthma management strategies; human resources needed for AMPCs; financial resources needed for AMPCs; and operational maintenance of AMPCs. Results: The workshop involved 39 participants, from all regions of the country, representing associations of asthma patients (n = 3), universities (n = 7), and AMPCs (n = 29). We found a direct relationship between a lack of planning and the failure of AMPCs. Based on the experiences reported during the workshop, the common assumptions about AMPCs in Brazil were the importance of raising awareness of managers; greater community participation; interdependence between primary care and specialized care; awareness of regionalization; and use of medications available in the public health system. Conclusions: Brazil already has a core of experience in the area of asthma management programs. The implementation of strategies for the management of chronic respiratory disease and their incorporation into health care system protocols would seem to be a natural progression. However, there is minimal experience in this area. Joint efforts by individuals with expertise in AMPCs could promote the implementation of asthma management strategies, thus speeding the creation of treatment networks, which might have a multiplier effect, precluding the need for isolated centers to start from zero. PMID:25750669

Wake field accelerators

International Nuclear Information System (INIS)

Wilson, P.B.

1986-02-01

In a wake field accelerator a high current driving bunch injected into a structure or plasma produces intense induced fields, which are in turn used to accelerate a trailing charge or bunch. The basic concepts of wake field acceleration are described. Wake potentials for closed cavities and periodic structures are derived, as are wake potentials on a collinear path with a charge distribution. Cylindrically symmetric structures excited by a beam in the form of a ring are considered

An accelerator technology legacy

International Nuclear Information System (INIS)

Heighway, E.A.

1994-01-01

Accelerator technology has been a major beneficiary of the investment made over the last decade. It is the intention of this paper to provide the reader with a glimpse of the broad nature of those advances. Development has been on a broad front and this paper can highlight only a few of those. Two spin-off applications will be outlined -- a concept for a compact, active, beam probe for solar body exploration and the concept for an accelerator-driven transmutation system for energy production

Architecture of the modern accelerator control system

International Nuclear Information System (INIS)

Samardzic, B.; Drndarevic, V.

2000-01-01

Well defined concept of the system and construction plan are the important conditions for the successful realization of the accelerator control system. In this paper the modern concept of accelerator control system as well as guidelines for its efficient development have been presented. Described concept could be applied for the design of control systems for other types of facilities for experimental physics and for industrial process control. (author)

Alternative Conceptions: Turning Adversity into Advantage

Science.gov (United States)

Ferreira, Annalize; Lemmer, Miriam; Gunstone, Richard

2017-08-01

While a vast body of research has identified difficulties in students' understanding about forces and acceleration and their related alternative conceptions, far less research suggests ways to use students' alternative conceptions to enhance conceptual understanding of a specific fundamental concept. This study focused on distinguishing between students' conceptual understanding of the Newtonian concept of gravitational acceleration being the same for all objects and students' alternative conception that heavy objects fall faster. A multiple choice questionnaire was distributed to first year physics students for three consecutive years at a university in South Africa. The results indicate that changing the direction of motion and the physics quantity asked in paired questions revealed practically significant inconsistencies in students' reasoning and conceptions. This research contributes to the body of knowledge in proposing how the alternative conception of mass-related gravitational acceleration can be used in instruction to enhance conceptual understanding of the force-mass-acceleration relationship. Understanding of this relationship not only promotes conceptual understanding of the basic Newtonian concepts of the laws of motion which forms the critical foundation on which more advanced physics courses are built, but also contributes towards students' perception of physics as a set of coherent ideas applicable in all contexts.

Overview of The Pulse Line Ion Accelerator

International Nuclear Information System (INIS)

Briggs, R.J.; Bieniosek, F.M.; Coleman, J.E.; Eylon, S.; Henestroza, E.; Leitner, M.; Logan, B.G.; Reginato, L.L.; Roy, P.K.; Seidl, P.A.; Waldron, W.L.; Yu, S.S.; Barnard, J.J.; Caporaso, G.J.; Friedman, A.; Grote, D.P.; Nelson, S.D.

2006-01-01

An overview of the Pulse Line Ion Accelerator (PLIA) concept and its development is presented. In the PLIA concept a pulse power driver applied to one end of a helical pulse line creates a traveling wave pulse that accelerates and axially confines a heavy ion beam pulse The motivation for its development at the IFE-VNL is the acceleration of intense, short pulse, heavy ion beams to regimes of interest for studies of High Energy Density Physics and Warm Dense Matter. Acceleration scenarios with constant parameter helical lines are described which result in output energies of a single stage much larger than the several hundred kilovolt peak voltages on the line, with a goal of 3-5 MeV/meter acceleration gradients. The main attraction of the concept is the very low cost it promises. It might be described crudely as an ''air core'' induction linac where the pulse-forming network is integrated into the beam line so the accelerating voltage pulse can move along with the ions to get voltage multiplication

Japanese contributions to IAEA INTOR workshop, phase IIA

International Nuclear Information System (INIS)

Fujisawa, Noboru; Sugihara, Masayoshi; Shimada, Michiya; Saito, Seiji.

1982-11-01

This report corresponds to Chapter VI of Japanese contribution report to IAEA INTOR workshop, Phase IIA. Special emphasis is placed on pumped limiter analysis for comparative studies between limiter and divertor concepts. Pumping characteristics of divertor/limiter and radiation cooling of diverted plasmas by impurities are also intensively studied. (author)

Spallator - accelerator breeder

International Nuclear Information System (INIS)

Steinberg, M.

1985-01-01

The concept involves the use of spallation neutrons produced by interaction of a high energy proton (1 to 2 GeV) from a linear accelerator (LINAC) with a heavy metal target (uranium). The principal spallator concept is based on generating fissile fuel for use in LWR nuclear power plants. The spallator functions in conjunction with a reprocessing plant to regenerate and produce the Pu-239 or U-233 for fabrication into fresh LWR reactor fuel elements. Advances in proton accelerator technology has provided a solid base for predicting performance and optimizing the design of a reliable, continuous wave, high-current LINAC required by a fissile fuel production machine

Physics with a high-intensity proton accelerator below 30 GeV

International Nuclear Information System (INIS)

Hoffman, C.M.

1982-01-01

The types of physics that would be pursued at a high-intensity, moderate-energy proton accelerator are discussed. The discussion is drawn from the deliberations of the 30-GeV subgroup of the Fixed-Target Group at this workshop

National workshop on "Exploring radiation in many Splendors"

CERN Document Server

2013-01-01

Theme : Application of radiation and related modes of detection This two-day workshop is focussed on the application of radiation in varied avenues of social and academic life. Motivation of the present programme is to make the M.Sc students and young researchers aware of the scope of this field of study. The workshop consists of invited plenary talks alongwith panel discussion and experimental demonstration. 1) Understanding basic Nuclear properties -- Radiation types and Detection Recent High Energy physics experiments at CERN Low energy nuclear physics experiments: Accelerator centres, Radiation labs 2) Probing the origin and composition of the Universe -- Detection and measurement of cosmic and galactic radiation Search for dark matter and dark energy 3) Emerging tools for Material characterization -- Synchrontron radiation Neutron Scattering 4) Nuclear medicine -- PET, SPECT Imaging Ion-beam therapy 5) Dosimetry and Radiation Safety

Summary of the 2014 Beam-Halo Monitoring Workshop

Energy Technology Data Exchange (ETDEWEB)

Fisher, Alan

2015-09-25

Understanding and controlling beam halo is important for high-intensity hadron accelerators, for high-brightness electron linacs, and for low-emittance light sources. This can only be achieved by developing suitable diagnostics. The main challenge faced by such instrumentation is the high dynamic range needed to observe the halo in the presence of an intense core. In addition, measurements must often be made non-invasively. This talk summarizes the one-day workshop on Beam-Halo Monitoring that was held at SLAC on September 19 last year, immediately following IBIC 2014 in Monterey. Workshop presentations described invasive techniques using wires, screens, or crystal collimators, and non-invasive measurements with gas or scattered electrons. Talks on optical methods showed the close links between observing halo and astronomical problems like observing the solar corona or directly observing a planet orbiting another star.

Proceedings of 'workshop on Pb-alloy cooled fast reactor'

International Nuclear Information System (INIS)

Kim, Sang Ji; Kim, Yong Hee; Hong, Ser Gi

2003-06-01

The objective of 'Workshop on Pb-Alloy Cooled Fast Reactor', held in Taejeon, Korea on May 6, 2003, is to enhance the basic knowledge in this area by facilitating the exchange of information and discussions about problematic area of design aspects. There were five presentations from three different countries and about 25 participants gathered during the workshop. The topics covered in the workshop include benefits and drawbacks of Pb-alloy and Sodium coolant, two Pb-alloy cooled 900 MWt reactor designs using both B4C rods and NSTs, BREST-300 breakeven reactor and transmutation effectiveness of LLFPs in the typical thermal/fast neutron systems. The generic conclusion for the Pb-alloy cooled fast reactor from this workshop is as follows: 1) It has a potential to satisfy the goals established for the Generation-IV reactor concepts, so it has a bright future. 2) As a fast neutron system with a moderate breeding or a conversion, it is flexible in its roles and has superior safety characteristics over sodium coolant because of Pb-alloy's chemical inertness with water/air and high boiling temperature

Nonlinear dynamics in particle accelerators

CERN Document Server

Dilão, Rui

1996-01-01

This book is an introductory course to accelerator physics at the level of graduate students. It has been written for a large audience which includes users of accelerator facilities, accelerator physicists and engineers, and undergraduates aiming to learn the basic principles of construction, operation and applications of accelerators.The new concepts of dynamical systems developed in the last twenty years give the theoretical setting to analyse the stability of particle beams in accelerator. In this book a common language to both accelerator physics and dynamical systems is integrated and dev

77 FR 31371 - Public Workshop: Privacy Compliance Workshop

Science.gov (United States)

2012-05-25

... presentations, including the privacy compliance fundamentals, privacy and data security, and the privacy... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary Public Workshop: Privacy Compliance... Homeland Security Privacy Office will host a public workshop, ``Privacy Compliance Workshop.'' DATES: The...

Preliminary Proceedings 15th International Workshop on Expressiveness in Concurrency

DEFF Research Database (Denmark)

The EXPRESS workshops aim at bringing together researchers interested in the relations between various formal systems, particularly in the field of Concurrency. More specifically, they focus on the comparison between programming concepts (such as concurrent, functional, imperative, logic and obje...

Allowance for insulation aging in the new concept of accelerated life tests of high-voltage power transformers

International Nuclear Information System (INIS)

Levit, A.G.; Grechko, O.N.; Shchipunova, N.P.

1992-01-01

This paper reports that the existing system of type and acceptance tests of high-voltage transformer insulation does not take into account insulation ageing, which is particularly objectionable with respect to equip-met with reduced insulation levels. Suggested in the paper is a new concept of accelerated life tests based on integrated simulation of basic operating loads, both periodic (surge) and long-term ones; by making a long-term accelerated test simulating the working conditions, with exposure of test object and/or its insulation to periodic operating surges (overvoltages and overcurrents). This test replaces a group of conventional individual acceptance tests and provides more ample and more precise information on performance and dependability of the equipment. The test procedure was checked in test of a small lot of 1600 kVA 35 kV power transformers

Report on impact fusion workshop, LASL, July 1979

International Nuclear Information System (INIS)

Russell, F.M.

1979-12-01

The concept of power production from thermonuclear fusion caused by inertial confinement of D,T fuel was examined from the standpoints of overall scientific feasibility and present state-of-art in the technologies involved. No defect in principle was found but much R and D work is needed in all aspects and especially that of accelerator devices. So far only one intrinsically stable macro-particle accelerator has been proposed, based on the mixed-μ concept of stability. (author)

Knowledge Management in TENCompetence: concepts & tools

NARCIS (Netherlands)

Lemmers, Ruud

2009-01-01

Lemmers, R. (2009). Knowledge Management in TENCompetence: concepts & tools. Presented at the 'Open workshop of TENCompetence - Rethinking Learning and Employment at a Time of Economic Uncertainty-event. November, 19, 2009, Manchester, United Kingdom: TENCompetence.

FORMATION OF THE PROJECT CONCEPT OF START PRE ACCELERATOR BY WAY OF BUSINESS MODEL BUILDING

Directory of Open Access Journals (Sweden)

Роман Васильович ФЕЩУР

2016-02-01

Full Text Available We have described the concept of the project of enterprise functioning, the main activity of which is the creation and implementation of training programs at the pre-investment stage and commercialize creative startups to represent them in the form attractive to investors. We also formed a flexible business model of enterprise-operator pre-accelerator at the base of Template A. Osterwalder. We have discovered the essence of the value proposition of enterprise-pre-accelerator. The company interaction with customers, among the main ones is: holders of startups, coworking, outsourcing companies, universities, "business angels" and sponsors were described. We have disclosed the role of human resources that create and convey to customers information about developed valuable suggestions. The basic activities of created business - production, customer satisfaction and building a platform (network were given. The risks of the project were found and their quantitative assessment was given. We noted that the successful implementation of each startup provides the appearance of not only economic but also social impact - creating new jobs, workers are provided with decent wages.

MICCAI Workshops

CERN Document Server

Nedjati-Gilani, Gemma; Venkataraman, Archana; O'Donnell, Lauren; Panagiotaki, Eleftheria

2014-01-01

This volume contains the proceedings from two closely related workshops: Computational Diffusion MRI (CDMRI’13) and Mathematical Methods from Brain Connectivity (MMBC’13), held under the auspices of the 16th International Conference on Medical Image Computing and Computer Assisted Intervention, which took place in Nagoya, Japan, September 2013. Inside, readers will find contributions ranging from mathematical foundations and novel methods for the validation of inferring large-scale connectivity from neuroimaging data to the statistical analysis of the data, accelerated methods for data acquisition, and the most recent developments on mathematical diffusion modeling. This volume offers a valuable starting point for anyone interested in learning computational diffusion MRI and mathematical methods for brain connectivity as well as offers new perspectives and insights on current research challenges for those currently in the field. It will be of interest to researchers and practitioners in computer science, ...

Optical Science: Deploying Technical Concepts and Engaging Participation through Digital Storytelling

Science.gov (United States)

Thomas, R. G.; Berry, K.; Arrigo, J.; Hooper, R. P.

2013-12-01

Technical 'hands-on' training workshops are designed to bring together scientists, technicians, and program managers from universities, government agencies, and the private sector to discuss methods used and advances made in instrumentation and data analysis. Through classroom lectures and discussions combined with a field-day component, hands-on workshop participants get a 'full life cycle' perspective from instrumentation concepts and deployment to data analysis. Using film to document this process is becoming increasingly more popular, allowing scientists to add a story-telling component to their research. With the availability of high-quality and low priced professional video equipment and editing software, scientists are becoming digital storytellers. The science video developed from the 'hands-on' workshop, Optical Water Quality Sensors for Nutrients: Concepts, Deployment, and Analysis, encapsulates the objectives of technical training workshops for participants. Through the use of still photography, video, interviews, and sound, the short video, An Introduction to CUAHSI's Hands-on Workshops, produced by a co-instructor of the workshop acts as a multi-purpose tool. The 10-minute piece provides an overview of workshop field day activities and works to bridge the gap between classroom learning, instrumentation application and data analysis. CUAHSI 'hands-on' technical workshops have been collaboratively executed with faculty from several universities and with the U.S. Geological Survey. The video developed was designed to attract new participants to these professional development workshops, to stimulate a connection with the environment, to act as a workshop legacy resource, and also serve as a guide for prospective hands-on workshop organizers. The effective use of film and short videos in marketing scientific programs, such as technical trainings, allows scientists to visually demonstrate the technologies currently being employed and to provide a more

Between the Stars: A Professional Development Workshop for Teachers

Science.gov (United States)

Hemenway, Mary Kay; Redfield, S.

2008-05-01

A workshop for secondary school science teachers was conducted at McDonald Observatory in July 2007. Participants did classroom experiments to detect and compare radiation in the ultraviolet, optical, and infrared regions of the electromagnetic spectrum. Other activities involved various aspects of stellar evolution and telescope design. They built spectrometers and considered how astronomers use scientific models. These topics were chosen to help them form a conceptual understanding of the parent projects' research topic: Variations in the Ionization Structure within the Local Interstellar Cloud and Neighboring Clouds. Fifteen teachers from Alaska, Idaho, Michigan, New York, Ohio, Oklahoma, and Texas performed these standards-aligned activities at the workshop in preparation for using them within their own classrooms. During three scheduled nights of observing, the participants became familiar with the night sky and the operation of small telescopes. The workshop included tours of other observatory facilities and time to reflect on their own teaching practices. They concluded the workshop by developing concept maps that integrated all aspects of the workshop, including lectures, activities, observing experiences, and tours. Support from The National Aeronautics and Space Administration under an Education and Public Outreach supplement to the Far Ultraviolet Spectroscopic Explorer Guest Investigator grant NNX07AN07G issued through the Office of Space Science is gratefully acknowledged.

[How to design workshops to promote health in community groups].

Science.gov (United States)

Hernández-Díaz, Josefina; Paredes-Carbonell, Joan J; Marín Torrens, Rosa

2014-01-01

One of the strategies of health promotion is to develop life skills people considering themselves as the main health resource. A workshop has to get its participants become «asset» to make decisions and create health, focusing on the development and acquisition of skills in a motivating group and in order to achieve health objectives. The concepts behind the design of a workshop are: participatory planning, training, meaningful learning, group learning and participatory techniques. The steps to follow to design a workshop and facilitate their application are: Stage 0, founding; initial stage, host and initial evaluation; central or construction stage based learning in the acquisition of knowledge, attitudes and skills, and final stage or evaluation. Copyright © 2013 Elsevier España, S.L. All rights reserved.

Workshops som forskningsmetode

OpenAIRE

Ørngreen, Rikke; Levinsen, Karin Tweddell

2017-01-01

This paper contributes to knowledge on workshops as a research methodology, and specifically on how such workshops pertain to e-learning. A literature review illustrated that workshops are discussed according to three different perspectives: workshops as a means, workshops as practice, and workshops as a research methodology. Focusing primarily on the latter, this paper presents five studies on upper secondary and higher education teachers’ professional development and on teaching and learnin...

Essential Concepts and Underlying Theories from Physics, Chemistry, and Mathematics for "Biochemistry and Molecular Biology" Majors

Science.gov (United States)

Wright, Ann; Provost, Joseph; Roecklein-Canfield, Jennifer A.; Bell, Ellis

2013-01-01

Over the past two years, through an NSF RCN UBE grant, the ASBMB has held regional workshops for faculty members from around the country. The workshops have focused on developing lists of Core Principles or Foundational Concepts in Biochemistry and Molecular Biology, a list of foundational skills, and foundational concepts from Physics, Chemistry,…

Report of the Fourth International Workshop on human X chromosome mapping 1993

Energy Technology Data Exchange (ETDEWEB)

Schlessinger, D.; Mandel, J.L.; Monaco, A.P.; Nelson, D.L.; Willard, H.F. [eds.

1993-12-31

Vigorous interactive efforts by the X chromosome community have led to accelerated mapping in the last six months. Seventy-five participants from 12 countries around the globe contributed progress reports to the Fourth International X Chromosome Workshop, at St. Louis, MO, May 9-12, 1993. It became clear that well over half the chromosome is now covered by YAC contigs that are being extended, verified, and aligned by their content of STSs and other markers placed by cytogenetic or linkage mapping techniques. The major aim of the workshop was to assemble the consensus map that appears in this report, summarizing both consensus order and YAC contig information.

DTU climate change technologies. Recommendations on accelerated development and deployment of climate change technologies

Energy Technology Data Exchange (ETDEWEB)

Larsen, Hans; Halsnaes, K [Technical Univ. of Denmark, Risoe National Lab. for Sustainable Energy, System Analysis Div., Roskilde (Denmark); Nielsen, Niels Axel; Moeller, J S; Hansen, Jakob Fritz; Froekjaer Strand, I [Technical Univ. of Denmark, Kgs. Lyngby (Denmark)

2009-09-15

During 2009, the Technical University of Denmark (DTU) has held a number of international workshops for climate change. Participants came from industry, research institutions and government. The workshops focused on sustainable energy systems and climate change adaptation. The summary of conclusions and recommendations from the workshops constitutes a comprehensive set of technology tracks and recommended actions towards accelerated development and deployment of technology within these two key areas. The workshop process has led to three main conclusions. A. Radical changes are needed to develop sustainable energy systems. B. Tools and processes that climate-proof societal planning and management are needed in order to adapt to climate change. C. Partnerships concerning innovation and deployment (research, development and deployment) are required to meet time constraints.

ISC High Performance 2017 International Workshops, DRBSD, ExaComm, HCPM, HPC-IODC, IWOPH, IXPUG, P^3MA, VHPC, Visualization at Scale, WOPSSS

CERN Document Server

Yokota, Rio; Taufer, Michela; Shalf, John

2017-01-01

This book constitutes revised selected papers from 10 workshops that were held as the ISC High Performance 2017 conference in Frankfurt, Germany, in June 2017. The 59 papers presented in this volume were carefully reviewed and selected for inclusion in this book. They stem from the following workshops: Workshop on Virtualization in High-Performance Cloud Computing (VHPC) Visualization at Scale: Deployment Case Studies and Experience Reports International Workshop on Performance Portable Programming Models for Accelerators (P^3MA) OpenPOWER for HPC (IWOPH) International Workshop on Data Reduction for Big Scientific Data (DRBSD) International Workshop on Communication Architectures for HPC, Big Data, Deep Learning and Clouds at Extreme Scale Workshop on HPC Computing in a Post Moore's Law World (HCPM) HPC I/O in the Data Center ( HPC-IODC) Workshop on Performance and Scalability of Storage Systems (WOPSSS) IXPUG: Experiences on Intel Knights Landing at the One Year Mark International Workshop on Communicati...

TeV/m Nano-Accelerator: Current Status of CNT-Channeling Acceleration Experiment

Energy Technology Data Exchange (ETDEWEB)

Shin, Young Min [Northern Illinois U.; Lumpkin, Alex H. [Fermilab; Thangaraj, Jayakar Charles [Fermilab; Thurman-Keup, Randy Michael [Fermilab; Shiltsev, Vladimir D. [Fermilab

2014-09-17

Crystal channeling technology has offered various opportunities in the accelerator community with a viability of ultrahigh gradient (TV/m) acceleration for future HEP collider. The major challenge of channeling acceleration is that ultimate acceleration gradients might require a high power driver in the hard x-ray regime (~ 40 keV). This x-ray energy exceeds those for x-rays as of today, although x-ray lasers can efficiently excite solid plasma and accelerate particles inside a crystal channel. Moreover, only disposable crystal accelerators are possible at such high externally excited fields which would exceed the ionization thresholds destroying the atomic structure, so acceleration will take place only in a short time before full dissociation of the lattice. Carbon-based nanostructures have great potential with a wide range of flexibility and superior physical strength, which can be applied to channeling acceleration. This paper presents a beam- driven channeling acceleration concept with CNTs and discusses feasible experiments with the Advanced Superconducting Test Accelerator (ASTA) in Fermilab.

Proceedings of the FNCA 2007 workshop on application of electron accelerator. Radiation processing of natural polymer

International Nuclear Information System (INIS)

Tamada, Masao; Kume, Tamikazu

2008-12-01

This workshop was co-sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT), Japan and the Ministry of Science and Technology (MOST), Vietnam. The Vietnam Atomic Energy Commission and Japan Atomic Energy Agency (JAEA) jointly executed the workshop in cooperation with the International Atomic Energy Agency (IAEA). The main objectives of the workshop were the following: - to discuss for the promotion of the commercial applications of radiation processing of natural polymer. - to prepare the work plan for the FNCA activities for 2007-2008. The workshop was attended by experts on radiation processing from Bangladesh, China, Egypt, India, Indonesia, Japan, Korea, Malaysia, Pakistan, Philippines, Sri Lanka, Thailand and Vietnam. The radiation processing of natural polymer is divided into crosslinking, degradation and graft polymerization. The radiation crosslinked polysaccharides are mainly used to prepare hydrogel for healthcare and environment. Hydrogels were commercialized in India, Korea, and Malaysia and are going to be commercialized in Philippines and Vietnam as wound dressings. Radiation degraded polysaccharides (alginate and chitosan) are commercialized in China and Vietnam in aquaculture and agriculture, respectively. Indonesia successfully carried out field test of radiation degraded chitosan as plant growth promoter. Also the radiation degraded chitosan was demonstrated to preserve post harvest fruit and to extend the shelf life of papaya in Pakistan and Sri Lanka, respectively. Radiation graft polymerization onto polysaccharide is applied for production of soil conditioner in Vietnam. Several applications of grafting technique were also reported. Manuscripts submitted by presenters were compiled in the proceedings. The 31 of the presented papers are indexed individually. (J.P.N.)

Social-emotional characteristics of gifted accelerated and non-accelerated students in the Netherlands.

Science.gov (United States)

Hoogeveen, Lianne; van Hell, Janet G; Verhoeven, Ludo

2012-12-01

In the studies of acceleration conducted so far a multidimensional perspective has largely been neglected. No attempt has been made to relate social-emotional characteristics of accelerated versus non-accelerated students in perspective of environmental factors. In this study, social-emotional characteristics of accelerated gifted students in the Netherlands were examined in relation to personal and environmental factors. Self-concept and social contacts of accelerated (n = 148) and non-accelerated (n = 55) gifted students, aged 4 to 27 (M = 11.22, SD = 4.27) were measured. Self-concept and social contacts of accelerated and non-accelerated gifted students were measured using a questionnaire and a diary, and parents of these students evaluated their behavioural characteristics. Gender and birth order were studied as personal factors and grade, classroom, teachers' gender, teaching experience, and the quality of parent-school contact as environmental factors. The results showed minimal differences in the social-emotional characteristics of accelerated and non-accelerated gifted students. The few differences we found favoured the accelerated students. We also found that multiple grade skipping does not have negative effects on social-emotional characteristics, and that long-term effects of acceleration tend to be positive. As regards the possible modulation of personal and environmental factors, we merely found an impact of such factors in the non-accelerated group. The results of this study strongly suggest that social-emotional characteristics of accelerated gifted students and non-accelerated gifted students are largely similar. These results thus do not support worries expressed by teachers about the acceleration of gifted students. Our findings parallel the outcomes of earlier studies in the United States and Germany in that we observed that acceleration does not harm gifted students, not even in the case of multiple grade skipping. On the contrary, there is a

Creativity and Self-Exploration in Projective Drawings of Abused Women: Evaluating the inside Me-outside Me Workshop

Science.gov (United States)

Dollinger, Stephen J.; Kazmierczak, Elzbieta; Storkerson, Peter K.

2011-01-01

This study evaluated a creative workshop where college students (N = 300) devised self-expressive products to explore their inner and outer worlds. Participants devised products with drawing and writing components to examine their relationships with negative life events, self-concepts, and worldviews. Participants then evaluated the workshop.…

Google SketchUp Workshop Modeling, Visualizing, and Illustrating

CERN Document Server

Brixius, Laurent

2010-01-01

Discover the secrets of the Google SketchUp with the 16 real-world professional-level projects including parks, structures, concept art, and illustration. Google SketchUp Workshop includes all the wide variety of projects that SketchUp can be used for-architectural visualization, landscape design, video game and film conception, and more. SketchUp masters in every field will get you up to speed in this agile and intuitive software and then show you the real uses with through projects in architecture, engineering, and design. * Packed with 16 real-world Go

MR-2016 US-Japan Workshop on Magentic Reconnection Travel Support

Energy Technology Data Exchange (ETDEWEB)

Forest, Cary [Univ. of Wisconsin, Madison, WI (United States)

2017-06-12

The US-Japan workshop on Magnetic Reconnection (MR2016), was held in Napa California from March 7th through 11th, 2016. Details about the program, including invited speakers can be found here: (http://www.magneticreconnection.org/mr2016). Background: The MR Workshop is an international meeting that began in 2000 with its original focus on magnetic reconnection serving as a link between the research groups in US and Japan. Since then, the meeting has grown and is now recognized as one of the primary international workshops on magnetic reconnection. In its format, researchers from both the laboratory community and from the space research community have held 12 workshops bringing together the diverse researchers from the space and laboratory experimental fields. Plasma physics is the common language that ties together all scientists who study the waves, particle acceleration and heating, magnetic reconnection, dynamos, global and micro-stability of plasmas, magnetic turbulence and plasma’s transport problems. The meeting received $9,575 from the U.S. Dept. of Energy funding. This support was used to cover the registration fees ($575 per person) and accommodations for ten junior colleagues (graduate students and postdocs). Applications were solicited and then reviewed by the program committee based on recommendations from the applicants’ advisers.

17th International Workshop on Neutrino Factories and Future Neutrino Facilities Search

CERN Document Server

2015-01-01

NuFact15 is the seventeenth in a series that started in 1999 as an important yearly workshop with emphasis on future neutrino projects. This will be the first edition in Latin America, showing the scientific growth of this field. The main goals of the workshop are to review the progress on studies of future facilities able to improve on measurements of the properties of neutrinos and charged lepton flavor violation as well as new phenomena searches beyond the capabilities of presently planned experiments. Since such progress in the neutrino sector could require innovation in neutrino beams, the role of a neutrino factory within future HEP initiatives will be addressed. The workshops are not only international but also interdisciplinary in that experimenters, theorists and accelerator physicists from the Asian, American and European regions share expertise with the common goal of designing the next generation of experiments.

Advanced concepts in accelerator timing control

International Nuclear Information System (INIS)

Frankel, R.; Salwen, C.

1988-01-01

The control system for the Booster accelerator presently under construction at BNL includes a timing section with serial high speed coded data distribution, computer based encoders for both real time and field driven clocks and a method of easily tracking the performance and reliability of these timing streams. We have developed a simple method for the generation of timing which operates to produce pulses which may be repeated as desired with minimal latency

Situated modelling in the drawing workshop for bobbin lace.

Science.gov (United States)

Saldanhar, Maria Christine Werba; de Almeida, Juliana Donato

2012-01-01

The current article presents the process of situated modeling in the drawing workshop for bobbin lace developed and implemented in the Núcleo de Produção Artesanal Rendeiras da Vila, in Ponta Negra, Natal-Brasil. The workshop aimed to rescue the domain over the product in the production of bobbin lace through capacitation of both experienced and novice craftswomen. The modeling of the drawing workshop was grounded on the sociotechnical construction and in the concepts of anthropotechnology and also social technology. The modelling required an intense process of social construction involving the members of GREPE-UFRN (Group of extension and Research in Ergonomics) and the lacemakers od the community. The domain of drawing the lace has enabled the expression of the craftswomen creativity, increasing the amount of works and the sustainable development,thus reducing the risks of extinction of such art in the Village of Ponta Negra.

Introduction to Microwave Linear [Accelerators

Energy Technology Data Exchange (ETDEWEB)

Whittum, David H

1999-01-04

The elements of microwave linear accelerators are introduced starting with the principles of acceleration and accelerating structures. Considerations for microwave structure modeling and design are developed from an elementary point of view. Basic elements of microwave electronics are described for application to the accelerator circuit and instrumentation. Concepts of beam physics are explored together with examples of common beamline instruments. Charged particle optics and lattice diagnostics are introduced. Considerations for fixed-target and colliding-beam experimentation are summarized.

HTTR workshop (workshop on hydrogen production technology)

International Nuclear Information System (INIS)

Shiina, Yasuaki; Takizuka, Takakazu

2004-12-01

Various research and development efforts have been performed to solve the global energy and environmental problems caused by large consumption of fossil fuels. Research activities on advanced hydrogen production technology by the use of nuclear heat from high temperature gas cooled reactors, for example, have been flourished in universities, research institutes and companies in many countries. The Department of HTTR Project and the Department of Advanced Nuclear Heat Technology of JAERI held the HTTR Workshop (Workshop on Hydrogen Production Technology) on July 5 and 6, 2004 to grasp the present status of R and D about the technology of HTGR and the nuclear hydrogen production in the world and to discuss about necessity of the nuclear hydrogen production and technical problems for the future development of the technology. More than 110 participants attended the Workshop including foreign participants from USA, France, Korea, Germany, Canada and United Kingdom. In the Workshop, the presentations were made on such topics as R and D programs for nuclear energy and hydrogen production technologies by thermo-chemical or other processes. Also, the possibility of the nuclear hydrogen production in the future society was discussed. The workshop showed that the R and D for the hydrogen production by the thermo-chemical process has been performed in many countries. The workshop affirmed that nuclear hydrogen production could be one of the competitive supplier of hydrogen in the future. The second HTTR Workshop will be held in the autumn next year. (author)

Genetic Engineering Workshop Report, 2010

Energy Technology Data Exchange (ETDEWEB)

Allen, J; Slezak, T

2010-11-03

The Lawrence Livermore National Laboratory (LLNL) Bioinformatics group has recently taken on a role in DTRA's Transformation Medical Technologies (TMT) program. The high-level goal of TMT is to accelerate the development of broad-spectrum countermeasures. To achieve this goal, there is a need to assess the genetic engineering (GE) approaches, potential application as well as detection and mitigation strategies. LLNL was tasked to coordinate a workshop to determine the scope of investments that DTRA should make to stay current with the rapid advances in genetic engineering technologies, so that accidental or malicious uses of GE technologies could be adequately detected and characterized. Attachment A is an earlier report produced by LLNL for TMT that provides some relevant background on Genetic Engineering detection. A workshop was held on September 23-24, 2010 in Springfield, Virginia. It was attended by a total of 55 people (see Attachment B). Twenty four (44%) of the attendees were academic researchers involved in GE or bioinformatics technology, 6 (11%) were from DTRA or the TMT program management, 7 (13%) were current TMT performers (including Jonathan Allen and Tom Slezak of LLNL who hosted the workshop), 11 (20%) were from other Federal agencies, and 7 (13%) were from industries that are involved in genetic engineering. Several attendees could be placed in multiple categories. There were 26 attendees (47%) who were from out of the DC area and received travel assistance through Invitational Travel Orders (ITOs). We note that this workshop could not have been as successful without the ability to invite experts from outside of the Beltway region. This workshop was an unclassified discussion of the science behind current genetic engineering capabilities. US citizenship was not required for attendance. While this may have limited some discussions concerning risk, we felt that it was more important for this first workshop to focus on the scientific state of

Report of On-Site Inspection Workshop-19

Energy Technology Data Exchange (ETDEWEB)

Sweeney, J. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2011-07-12

The objective of this workshop was to carry out discussions on the OSI Equipment List for the initial period techniques and to provide further contribution to the development of the OSI Equipment List. The report of the 36th session of WGB included guidance to develop corresponding concepts of operations for the equipment, identify logistics and infrastructure requirements, and to address software issues related to the equipment.

Citizen Data and Official Statistics: Background Document to a Collaborative Workshop

DEFF Research Database (Denmark)

Grommé, Francisca; Ustek, Funda; Ruppert, Evelyn

2017-01-01

This working paper was written in preparation for a collaborative workshop organised for statisticians, social scientists, information and app designers and other participants inside and outside academia. The autumn 2017 workshop aimed to develop the main principles for a citizen data app...... for official statistics. Through this work we sought to conceive of a new regime of data collection in official statistics through different devices. How can we capture citizens’ meanings and intentions when they produce data? Can we develop ‘smart’ methods that do not rely on cooperating with, and data...... generated by, large tech companies, but by developing methods and data co-produced with citizens? Towards addressing these issues we developed four key concepts outlined in this document: experimentalism, citizen data, smart statistics and privacy by design. We introduced these concepts to facilitate shared...

Proceedings of the 2016 Workshop on the Physics and Applications of High Brightness Beams

Science.gov (United States)

Cianchi, Alessandro; Ferrario, Massimo; Musumeci, Pietro; Rosenzweig, James

2017-09-01

We are proud to present the proceedings of the latest in the series of International Committee on Future Accelerators (ICFA)-endorsed workshops on the Physics and Applications of High Brightness Beams, which has been held at the Hotel Nacional in Havana, Cuba between March 28 and April 1, 2016. In total, 135 participants coming from 14 different countries attended this historic conference. In recognition of its pioneering role in the significant blossoming of relations between Cuba and the larger scientific community, this workshop also received the endorsement of UNESCO. The workshop organization was headed by co-chairs Massimo Ferrario (INFN-LNF) and James Rosenzweig (UCLA), with the essential and energetic contributions of local organizing committee chair Fidel Antonio Castro Smirnov (InSTEC, Havana). The workshop scientific agenda was developed under the care of program committee co-chairs Pietro Musumeci (UCLA) and Luca Serafini (INFN-Milano). The publication of the proceedings we present here was led by Alessandro Cianchi (Tor Vergata). Tangible contributions to the workshop infrastructure were received from UCLA, INFN-LNF, InSTEC, EuroNNAC2, and the US National Science Foundation. The workshop web site, which contains detailed information on the scientific agenda of the meeting, is found at https://conferences.pa.ucla.edu/hbb/.

Accelerating cancer therapy development: the importance of combination strategies and collaboration. Summary of an Institute of Medicine workshop.

Science.gov (United States)

LoRusso, Patricia M; Canetta, Renzo; Wagner, John A; Balogh, Erin P; Nass, Sharyl J; Boerner, Scott A; Hohneker, John

2012-11-15

Cancer cells contain multiple genetic changes in cell signaling pathways that drive abnormal cell survival, proliferation, invasion, and metastasis. Unfortunately, patients treated with single agents inhibiting only one of these pathways--even if showing an initial response--often develop resistance with subsequent relapse or progression of their cancer, typically via the activation of an alternative uninhibited pathway. Combination therapies offer the potential for inhibiting multiple targets and pathways simultaneously to more effectively kill cancer cells and prevent or delay the emergence of drug resistance. However, there are many unique challenges to developing combination therapies, including devising and applying appropriate preclinical tests and clinical trial designs, prioritizing which combination therapies to test, avoiding overlapping toxicity of multiple agents, and overcoming legal, cultural, and regulatory barriers that impede collaboration among multiple companies, organizations, and/or institutions. More effective strategies to efficiently develop combination cancer therapies are urgently needed. Thus, the Institute of Medicine's National Cancer Policy Forum recently convened a workshop with the goal of identifying barriers that may be impeding the development of combination investigational cancer therapies, as well as potential solutions to overcome those barriers, improve collaboration, and ultimately accelerate the development of promising combinations of investigational cancer therapies. ©2012 AACR.

"Think Tank" Workshop in Work Evaluation: March 19-21, 1969.

Science.gov (United States)

Hoffman, Paul R., Ed.

A two-day workshop, conducted to study the different meanings of the concept of work evaluation, was participated in by representatives from rehabilitation facilities, work evaluation training programs, institutional organizations, and rehabilitation research and training centers. In addition, different types of patient populations were…

Linear accelerators for TeV colliders. Revision

International Nuclear Information System (INIS)

Wilson, P.B.

1985-10-01

The basic scaling relations for important linear collider design parameters are introduced. Some of the basic concepts concerning the design of accelerating structures are presented, and breakdown limitations are discussed. Rf power sources are considered. Some of the key concepts of wakefield accelerators are discussed, and some examples of wake fields for typical linac structures are presented. Some general concepts concerning emittance, and the limitations on the emittance that can be obtained from linac guns and damping rings are discussed. 49 refs., 15 figs

A post-accelerator for the US rare isotope accelerator facility

CERN Document Server

Ostroumov, P N; Kolomiets, A A; Nolen, J A; Portillo, M; Shepard, K W; Vinogradov, N E

2003-01-01

The proposed rare isotope accelerator (RIA) facility includes a post-accelerator for rare isotopes (RIB linac) which must produce high-quality beams of radioactive ions over the full mass range, including uranium, at energies above the Coulomb barrier, and have high transmission and efficiency. The latter requires the RIB linac to accept at injection ions in the 1+ charge state. A concept for such a post accelerator suitable for ions up to mass 132 has been previously described . This paper presents a modified concept which extends the mass range to uranium. A high resolution separator for purifying beams at the isobaric level precedes the RIB linac. The mass filtering process will provide high purity beams while preserving transmission. For most cases a resolution of about m/DELTA m=20 000 is adequate at mass A=100 to obtain a separation between isobars of mass excess difference of 5 MeV. The design for a device capable of purifying beams at the isobaric level includes calculations up to fifth order. The RIB...

Health physics practices at research accelerators

International Nuclear Information System (INIS)

Thomas, R.H.

1976-02-01

A review is given of the uses of particle accelerators in health physics, the text being a short course given at the Health Physics Society Ninth Midyear Topical Symposium in February, 1976. Topics discussed include: (1) the radiation environment of high energy accelerators; (2) dosimetry at research accelerators; (3) shielding; (4) induced activity; (5) environmental impact of high energy accelerators; (6) population dose equivalent calculation; and (7) the application of the ''as low as practicable concept'' at accelerators

Collective accelerator for electron colliders

Energy Technology Data Exchange (ETDEWEB)

Briggs, R.J.

1985-05-13

A recent concept for collective acceleration and focusing of a high energy electron bunch is discussed, in the context of its possible applicability to large linear colliders in the TeV range. The scheme can be considered to be a member of the general class of two-beam accelerators, where a high current, low voltage beam produces the acceleration fields for a trailing high energy bunch.

Collective accelerator for electron colliders

International Nuclear Information System (INIS)

Briggs, R.J.

1985-01-01

A recent concept for collective acceleration and focusing of a high energy electron bunch is discussed, in the context of its possible applicability to large linear colliders in the TeV range. The scheme can be considered to be a member of the general class of two-beam accelerators, where a high current, low voltage beam produces the acceleration fields for a trailing high energy bunch

Proceedings: Power Plant Electric Auxiliary Systems Workshop

International Nuclear Information System (INIS)

1992-06-01

The EPRI Power Plant Electric Auxiliary Systems Workshop, held April 24--25, 1991, in Princeton, New Jersey, brought together utilities, architect/engineers, and equipment suppliers to discuss common problems with power plant auxiliary systems. Workshop participants presented papers on monitoring, identifying, and solving problems with auxiliary systems. Panel discussions focused on improving systems and existing and future plants. The solutions presented to common auxiliary system problems focused on practical ideas that can enhance plant availability, reduce maintenance costs, and simplify the engineering process. The 13 papers in these proceedings include: Tutorials on auxiliary electrical systems and motors; descriptions of evaluations, software development, and new technologies used recently by electric utilities; an analysis of historical performance losses caused by power plant auxiliary systems; innovative design concepts for improving auxiliary system performance in future power plants

Streaming Visual Analytics Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Cook, Kristin A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Burtner, Edwin R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kritzstein, Brian P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Brisbois, Brooke R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mitson, Anna E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-03-31

How can we best enable users to understand complex emerging events and make appropriate assessments from streaming data? This was the central question addressed at a three-day workshop on streaming visual analytics. This workshop was organized by Pacific Northwest National Laboratory for a government sponsor. It brought together forty researchers and subject matter experts from government, industry, and academia. This report summarizes the outcomes from that workshop. It describes elements of the vision for a streaming visual analytic environment and set of important research directions needed to achieve this vision. Streaming data analysis is in many ways the analysis and understanding of change. However, current visual analytics systems usually focus on static data collections, meaning that dynamically changing conditions are not appropriately addressed. The envisioned mixed-initiative streaming visual analytics environment creates a collaboration between the analyst and the system to support the analysis process. It raises the level of discourse from low-level data records to higher-level concepts. The system supports the analyst’s rapid orientation and reorientation as situations change. It provides an environment to support the analyst’s critical thinking. It infers tasks and interests based on the analyst’s interactions. The system works as both an assistant and a devil’s advocate, finding relevant data and alerts as well as considering alternative hypotheses. Finally, the system supports sharing of findings with others. Making such an environment a reality requires research in several areas. The workshop discussions focused on four broad areas: support for critical thinking, visual representation of change, mixed-initiative analysis, and the use of narratives for analysis and communication.

STREAM2016: Streaming Requirements, Experience, Applications and Middleware Workshop

Energy Technology Data Exchange (ETDEWEB)

Fox, Geoffrey [Indiana Univ., Bloomington, IN (United States); Jha, Shantenu [Rutgers Univ., New Brunswick, NJ (United States); Ramakrishnan, Lavanya [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2016-10-01

The Department of Energy (DOE) Office of Science (SC) facilities including accelerators, light sources and neutron sources and sensors that study, the environment, and the atmosphere, are producing streaming data that needs to be analyzed for next-generation scientific discoveries. There has been an explosion of new research and technologies for stream analytics arising from the academic and private sectors. However, there has been no corresponding effort in either documenting the critical research opportunities or building a community that can create and foster productive collaborations. The two-part workshop series, STREAM: Streaming Requirements, Experience, Applications and Middleware Workshop (STREAM2015 and STREAM2016), were conducted to bring the community together and identify gaps and future efforts needed by both NSF and DOE. This report describes the discussions, outcomes and conclusions from STREAM2016: Streaming Requirements, Experience, Applications and Middleware Workshop, the second of these workshops held on March 22-23, 2016 in Tysons, VA. STREAM2016 focused on the Department of Energy (DOE) applications, computational and experimental facilities, as well software systems. Thus, the role of “streaming and steering” as a critical mode of connecting the experimental and computing facilities was pervasive through the workshop. Given the overlap in interests and challenges with industry, the workshop had significant presence from several innovative companies and major contributors. The requirements that drive the proposed research directions, identified in this report, show an important opportunity for building competitive research and development program around streaming data. These findings and recommendations are consistent with vision outlined in NRC Frontiers of Data and National Strategic Computing Initiative (NCSI) [1, 2]. The discussions from the workshop are captured as topic areas covered in this report's sections. The report

Report of the workshop on rf heating in mirror systems

International Nuclear Information System (INIS)

Price, R.E.; Woo, J.T.

1980-08-01

This report is prepared from the proceedings of the Workshop on RF Heating in Magnetic Mirror Systems held at DOE Headquarters in Washington, DC, on March 10-12, 1980. The workshop was organized into four consecutive half-day sessions of prepared talks and one half-day discussion. The first session on tandem mirror concepts and program plans served to identify the opportunities for the application of rf power and the specific approaches that are being pursued. A summary of the ideas presented in this session is given. The following sessions of the workshop were devoted to an exposition of current theoretical and experimental knowledge on the interaction of rf power with magnetically confined, dense, high temperature plasmas at frequencies near the electron cyclotron resonance, lower hybrid resonance and ion cyclotron resonance (including magnetosonic) ranges. The conclusions from these proceedings are presented

A workshop on enhanced national capability for neutron scattering

Energy Technology Data Exchange (ETDEWEB)

Hurd, Alan J [Los Alamos National Laboratory; Rhyne, James J [Los Alamos National Laboratory; Lewis, Paul S [Los Alamos National Laboratory

2009-01-01

This two-day workshop will engage the international neutron scattering community to vet and improve the Lujan Center Strategic Plan 2007-2013 (SP07). Sponsored by the LANL SC Program Office and the University of California, the workshop will be hosted by LANSCE Professor Sunny Sinha (UCSD). Endorsement by the Spallation Neutron Source will be requested. The discussion will focus on the role that the Lujan Center will play in the national neutron scattering landscape assuming full utilization of beamlines, a refurbished LANSCE, and a 1.4-MW SNS. Because the Lujan Strategic Plan is intended to set the stage for the Signature Facility era at LANSCE, there will be some discussion of the long-pulse spallation source at Los Alamos. Breakout groups will cover several new instrument concepts, upgrades to present instruments, expanded sample environment capabilities, and a look to the future. The workshop is in keeping with a request by BES to update the Lujan strategic plan in coordination with the SNS and the broader neutron community. Workshop invitees will be drawn from the LANSCE User Group and a broad cross section of the US, European, and Pacific Rim neutron scattering research communities.

78 FR 32010 - Pipeline Safety: Public Workshop on Integrity Verification Process

Science.gov (United States)

2013-05-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket No... Hazardous Materials Safety Administration, DOT. ACTION: Notice of public meeting. SUMMARY: This notice is announcing a public workshop to be held on the concept of ``Integrity Verification Process.'' The Integrity...

Summary proceedings of a workshop on Bioremediation and its Societal Implications and Concerns (BASIC)

Energy Technology Data Exchange (ETDEWEB)

Drell, D.W. [Department of Energy, Germantown, MD (United States). Office of Health and Environmental Research, Health Effects and Life Sciences Research Division; Metting, F.B. Jr. [Pacific Northwest National Lab., Richland, WA (United States); Wuy, L.D. [ed.] [Lawrence Berkeley National Lab., CA (United States)

1996-11-01

This document summarizes the proceedings of a workshop on Bioremediation and Its Societal Implications and Concerns (BASIC) held July 18-19, 1996 at the Airlie Center near Warrenton, Virginia. The workshop was sponsored by the Office of Health and Environmental Research (OHER), U.S. Department of Energy (DOE), as part of its fundamental research program in Natural and Accelerated Bioremediation Research (NABIR). The information summarized in these proceedings represents the general conclusions of the workshop participants, and not the opinions of workshop organizers or sponsors. Neither are they consensus opinions, as opinions differed among participants on a number of points. The general conclusions presented below were reached through a review, synthesis, and condensation of notes taken by NABIR Program Office staff and OHER program managers throughout the workshop. Specific contributions by participants during breakout sessions are recorded in bullet form in the appropriate sections, without attribution to the contributors. These contributions were transcribed as faithfully as possible from notes about the original discussions. They were edited only to make them grammatically correct, parallel in structure, and understandable to someone not familiar with the NABIR Program or BASIC element.

Summary proceedings of a workshop on Bioremediation and its Societal Implications and Concerns (BASIC)

International Nuclear Information System (INIS)

Drell, D.W.; Wuy, L.D.

1996-11-01

This document summarizes the proceedings of a workshop on Bioremediation and Its Societal Implications and Concerns (BASIC) held July 18-19, 1996 at the Airlie Center near Warrenton, Virginia. The workshop was sponsored by the Office of Health and Environmental Research (OHER), U.S. Department of Energy (DOE), as part of its fundamental research program in Natural and Accelerated Bioremediation Research (NABIR). The information summarized in these proceedings represents the general conclusions of the workshop participants, and not the opinions of workshop organizers or sponsors. Neither are they consensus opinions, as opinions differed among participants on a number of points. The general conclusions presented below were reached through a review, synthesis, and condensation of notes taken by NABIR Program Office staff and OHER program managers throughout the workshop. Specific contributions by participants during breakout sessions are recorded in bullet form in the appropriate sections, without attribution to the contributors. These contributions were transcribed as faithfully as possible from notes about the original discussions. They were edited only to make them grammatically correct, parallel in structure, and understandable to someone not familiar with the NABIR Program or BASIC element

New ideas for accelerating particles

International Nuclear Information System (INIS)

Lawson, J.D.

1983-01-01

Many different schemes can be devised for accelerating particles. In recent years several concepts radically different from those in common use have been suggested. Many of these have failed to live up to the hopes of their inventors. Now that we seem near the end of the road for large conventional machines, there is a renewed interest in alternatives, especially those involving lasers. Afte After a brief historical introduction and a discussion on how to classify different types of accelerator, some of these alternative concepts will be reviewed. (author)

Concept for a lead-ion accelerating facility at CERN

International Nuclear Information System (INIS)

Billinge, R.; Boltezar, E.; Boussard, D.; Brouzet, E.; Cappi, R.; Raad, B. de; Doble, N.; Grafstroem, P.; Haseroth, H.; Hill, C.E.; Kissler, K.H.; Knott, J.; Linnecar, T.; Nitsch, F.; Poncet, A.; Raich, U.; Rasmussen, N.; Schoenauer, H.; Sherwood, T.R.; Siegel, N.; Tallgren, U.; Tetu, P.; Warner, D.; Weiss, M.

1990-01-01

After the successful acceleration of deuterons, alpha particles and in more recent years of oxygen and sulphur ions, interest arose for even heavier particles. This paper describes the problems associated with heavy ions. A proposal is made for a scenario which allows the CERN accelerators to cope with ions heavier than sulphur, e.g. lead. Discussed are the different options for the injector and the necessary upgrading for the circular machines. (orig.)

Joint CARE-ELAN, CARE-HHH-APD, and EUROTEV-WP3 Workshop on Electron Cloud Clearing

CERN Document Server

Scandale, Walter; Schulte, D; Zimmermann, F; Electron Cloud Effects and Technological Consequences; ECL2

2007-01-01

This report contains the Proceedings of the joint CARE-HHH-APD, CARE-ELAN, and EUROTEV-WP3 Mini-Workshop on 'Electron Cloud Clearing - Electron Cloud and Technical Consequences', "ECL2", held at CERN in Geneva, Switzerland, 1-2 March 2007). The ECL2 workshop explored novel technological remedies against electron-cloud formation in an accelerator beam pipe. A primary motivation for the workshop was the expected harmful electron-cloud effects in the upgraded LHC injectors and in future linear colliders, as well as recent beam observations in operating facilities like ANKA, CESR, KEKB, RHIC, and SPS. The solutions discussed at ECL2 included enamel-based clearing electrodes, slotted vacuum chambers, NEG coating, and grooves. Several of the proposed cures were assessed in terms of their clearing efficiency and the associated beam impedance. The workshop also reviewed new simulation tools like the 3D electron-ion build-up 'Faktor', modeling assumptions, analytical calculations, beam experiments, and laboratory meas...

A workshop on leadership for senior MD–PhD students

Science.gov (United States)

Meador, Catherine B.; Parang, Bobak; Musser, Melissa A.; Haliyur, Rachana; Owens, David A.; Dermody, Terence S.

2016-01-01

Leadership skills are essential for a successful career as a physician-scientist, yet many MD–PhD training programs do not offer formal training in leadership. The Vanderbilt Medical Scientist Training Program (MSTP) previously established a 2-day leadership workshop that has been held biennially since 2006 for students in the first and second years of the graduate school portion of combined MD and PhD training (G1/G2 students). Workshop attendees have consistently rated this workshop as a highly effective experience. However, opportunities for structured training in leadership competencies during the subsequent 3–5 years of MD–PhD training are limited. Given the success of the G1/G2 leadership workshop and the need for continuity in this model of leadership training, we developed a half-day workshop for MSTP students in the clinical years of medical school (M3/M4 students) to foster continued training in leadership. Our workshop curriculum, based in part on original cases drafted by Vanderbilt MSTP students, provides concrete strategies to manage conflict and navigate leadership transitions in the physician-scientist career path. The curriculum emphasizes both short-term competencies, such as effective participation as a member of a clinical team, and long-term competencies, such as leadership of a research team, division, or department. Our inaugural senior leadership workshop, held in August, 2015, was judged by student participants to be well organized and highly relevant to leadership concepts and skills. It will be offered biennially in our training curriculum for M3 and M4 MSTP students. PMID:27499363

A workshop on leadership for senior MD-PhD students.

Science.gov (United States)

Meador, Catherine B; Parang, Bobak; Musser, Melissa A; Haliyur, Rachana; Owens, David A; Dermody, Terence S

2016-01-01

Leadership skills are essential for a successful career as a physician-scientist, yet many MD-PhD training programs do not offer formal training in leadership. The Vanderbilt Medical Scientist Training Program (MSTP) previously established a 2-day leadership workshop that has been held biennially since 2006 for students in the first and second years of the graduate school portion of combined MD and PhD training (G1/G2 students). Workshop attendees have consistently rated this workshop as a highly effective experience. However, opportunities for structured training in leadership competencies during the subsequent 3-5 years of MD-PhD training are limited. Given the success of the G1/G2 leadership workshop and the need for continuity in this model of leadership training, we developed a half-day workshop for MSTP students in the clinical years of medical school (M3/M4 students) to foster continued training in leadership. Our workshop curriculum, based in part on original cases drafted by Vanderbilt MSTP students, provides concrete strategies to manage conflict and navigate leadership transitions in the physician-scientist career path. The curriculum emphasizes both short-term competencies, such as effective participation as a member of a clinical team, and long-term competencies, such as leadership of a research team, division, or department. Our inaugural senior leadership workshop, held in August, 2015, was judged by student participants to be well organized and highly relevant to leadership concepts and skills. It will be offered biennially in our training curriculum for M3 and M4 MSTP students.

A workshop on leadership for senior MD–PhD students

Directory of Open Access Journals (Sweden)

Catherine B. Meador

2016-08-01

Full Text Available Leadership skills are essential for a successful career as a physician-scientist, yet many MD–PhD training programs do not offer formal training in leadership. The Vanderbilt Medical Scientist Training Program (MSTP previously established a 2-day leadership workshop that has been held biennially since 2006 for students in the first and second years of the graduate school portion of combined MD and PhD training (G1/G2 students. Workshop attendees have consistently rated this workshop as a highly effective experience. However, opportunities for structured training in leadership competencies during the subsequent 3–5 years of MD–PhD training are limited. Given the success of the G1/G2 leadership workshop and the need for continuity in this model of leadership training, we developed a half-day workshop for MSTP students in the clinical years of medical school (M3/M4 students to foster continued training in leadership. Our workshop curriculum, based in part on original cases drafted by Vanderbilt MSTP students, provides concrete strategies to manage conflict and navigate leadership transitions in the physician-scientist career path. The curriculum emphasizes both short-term competencies, such as effective participation as a member of a clinical team, and long-term competencies, such as leadership of a research team, division, or department. Our inaugural senior leadership workshop, held in August, 2015, was judged by student participants to be well organized and highly relevant to leadership concepts and skills. It will be offered biennially in our training curriculum for M3 and M4 MSTP students.

16th International Workshop on Neutrino Factories and Future Neutrino Beam Facilities

CERN Document Server

2015-01-01

These proceedings present the written contributions from participants of the 16th International Workshop on Neutrino Factories and Future Neutrino Beam Facilities (NUFACT 2014) that was held at the University of Glasgow (Glasgow, Scotland, United Kingdom) from 25-30 August 2014. This edition of the NUFACT annual meetings, which started in 1999, consisted of 24 plenary and 92 parallel talks and various poster sessions, with the participation of 124 delegates. Furthermore, the International Neutrino Summer School 2014 was held from 10-22 August 2014 at St Andrews, Scotland, in the two weeks before NUFACT 2014. It was intended for young scientists with an interest in neutrino physics in such a way that they would be able to participate and contribute to the NUFACT workshop as well. The objectives of the NUFACT workshops are to review progress on different studies for future accelerator-based neutrino oscillation facilities, with the goal to discover the mass hierarchy of neutrinos, CP violation in the leptonic s...

Lunar Reconnaissance Orbiter Lunar Workshops for Educators

Science.gov (United States)

Jones, A. P.; Hsu, B. C.; Hessen, K.; Bleacher, L.

2012-12-01

The Lunar Workshops for Educators (LWEs) are a series of weeklong professional development workshops, accompanied by quarterly follow-up sessions, designed to educate and inspire grade 6-12 science teachers, sponsored by the Lunar Reconnaissance Orbiter (LRO). Participants learn about lunar science and exploration, gain tools to help address common student misconceptions about the Moon, find out about the latest research results from LRO scientists, work with data from LRO and other lunar missions, and learn how to bring these data to their students using hands-on activities aligned with grade 6-12 National Science Education Standards and Benchmarks and through authentic research experiences. LWEs are held around the country, primarily in locations underserved with respect to NASA workshops. Where possible, workshops also include tours of science facilities or field trips intended to help participants better understand mission operations or geologic processes relevant to the Moon. Scientist and engineer involvement is a central tenant of the LWEs. LRO scientists and engineers, as well as scientists working on other lunar missions, present their research or activities to the workshop participants and answer questions about lunar science and exploration. This interaction with the scientists and engineers is consistently ranked by the LWE participants as one of the most interesting and inspiring components of the workshops. Evaluation results from the 2010 and 2011 workshops, as well as preliminary analysis of survey responses from 2012 participants, demonstrated an improved understanding of lunar science concepts among LWE participants in post-workshop assessments (as compared to identical pre-assessments) and a greater understanding of how to access and effectively share LRO data with students. Teachers reported increased confidence in helping students conduct research using lunar data, and learned about programs that would allow their students to make authentic

Consultation and concurrence: workshop proceedings, September 23-26, 1979, the Orcas meeting, Eastsound, Washington

International Nuclear Information System (INIS)

1980-01-01

Purpose of the workshop was to probe the concepts of consultation and concurrence and to address issues in establishing and maintaining an effective state-federal process in nuclear waste management. The workshop was a gathering of some 50 people from industry, the environmental movement, local government, executive and legislative branches of state government, US Congressional staffs, the US Department of Energy, Nuclear Regulatory Commission, ONWI, university social science departments, and other research institutions. The workshop consisted of general sessions at which ten papers covering various aspects of consultation and concurrence were presented and of working groups which further explored issues raised by the papers. This report presents a general summary of discussions, the text of a background paper prepared for the workshop, the presented papers, and individual comments by several participants

Tracking and vertexing for B physics at hadron accelerators

International Nuclear Information System (INIS)

Johnson, R.; Purohit, M.; Weidemann, A.W.

1993-01-01

In this note, the authors report on some of the activities of the Tracking and Vertexing Working Group of this Workshop. Track and vertex finding is essential to exploit the high production rate of B-mesons at hadron accelerators, both for triggering and analysis. Here, they review the tracking and vertex-finding systems of some of the major existing and proposed collider and fixed-target experiments at existing and future hadron accelerators, with a view towards their usefulness for B-physics. The capabilities of both general-purpose detectors and those of dedicated B-physics experiments are considered

The accelerator breeder

International Nuclear Information System (INIS)

Johansson, E.

1986-01-01

Interactions of high-energy particles with atomic nuclei, in particular heavy ones, leads to a strong emission of neutrons. Preferably these high-energy particles are protons or deuterons obtained from a linear accelerator. The neutrons emitted are utilized in the conversion of U238 to Pu239 or of Th232 to U233. The above is the basis of the accelerator breeder, a concept studied abroad in many variants. No such breeder has, however, so far been built, but there exists vast practical experience on the neutron production and on the linear accelerator. Some of the variants mentioned are described in the report, after a presentation of general characteristics for the particle-nucleus interaction and for the linear accelerator. (author)

Large hadron collider workshop. Proceedings. Vol. 3

International Nuclear Information System (INIS)

Jarlskog, G.; Rein, D.

1990-01-01

The aim of the LHC workshop at Aachen was to discuss the 'discovery potential' of a high-luminosity hadron collider (the Large Hadron Collider) and to define the requirements of the detectors. Of central interest was whether a Higgs particle with mass below 1 TeV could be seen using detectors potentially available within a few years from now. Other topics included supersymmetry, heavy quarks, excited gauge bosons, and exotica in proton-proton collisions, as well as physics to be observed in electron-proton and heavy-ion collisions. A large part of the workshop was devoted to the discussion of instrumental and detector concepts, including simulation, signal processing, data acquisition, tracking, calorimetry, lepton identification and radiation hardness. The workshop began with parallel sessions of working groups on physics and instrumentaiton and continued, in the second half, with plenary talks giving overviews of the LHC project and the SSC, RHIC, and HERA programmes, summaries of the working groups, presentations from industry, and conclusions. Vol. 1 of these proceedings contains the papers presented at the plenary sessions, Vol. 2 the individual contributions to the physics sessions, and Vol. 3 those to the instrumentation sessions. (orig.)

Large hadron collider workshop. Proceedings. Vol. 2

International Nuclear Information System (INIS)

Jarlskog, G.; Rein, D.

1990-01-01

The aim of the LHC workshop at Aachen was to discuss the 'discovery potential' of a high-luminosity hadron collider (the Large Hadron Collider) and to define the requirements of the detectors. Of central interest was whether a Higgs particle with mass below 1 TeV could be seen using detectors potentially available within a few years from now. Other topics included supersymmetry, heavy quarks, excited gauge bosons, and exotica in proton-proton collisions, as well as physics to be observed in electron-proton and heavy-ion collisions. A large part of the workshop was devoted to the discussion of instrumental and detector concepts, including simulation, signal processing, data acquisition, tracking, calorimetry, lepton identification and radiation hardness. The workshop began with parallel sessions of working groups on physics and instrumentation and continued, in the second half, with plenary talks giving overviews of the LHC project and the SSC, RHIC, and HERA programmes, summaries of the working groups, presentations from industry, and conclusions. Vol.1 of these proceedings contains the papers presented at the plenary sessions, Vol.2 the individual contributions to the physics sessions, and Vol.3 those to the instrumentation sessions. (orig.)

Large hadron collider workshop. Proceedings. Vol. 1

International Nuclear Information System (INIS)

Jarlskog, G.; Rein, D.

1990-01-01

The aim of the LCH workshop at Aachen was to discuss the 'discovery potential' of a high-luminosity hadron collider (the Large Hadron Collider) and to define the requirements of the detectors. Of central interest was whether a Higgs particle with mass below 1 TeV could be seen using detectors potentially available within a few years from now. Other topics included supersymmetry, heavy quarks, excited gauge bosons, and exotica in proton-proton collisions, as well as physics to be observed in electron-proton and heavy-ion collisions. A large part of the workshop was devoted to the discussion of instrumental and detector concepts, including simulation, signal processing, data acquisition, tracking, calorimetry, lepton identification and radiation hardness. The workshop began with parallel sessions of working groups on physics and instrumentation and continued, in the second half, with plenary talks giving overviews of the LHC project and the SSC, RHIC, and HERA programmes, summaries of the working groups, presentations from industry, and conclusions. Vol. 1 of these proceedings contains the papers presented at the plenary sessions, Vol. 2 the individual contributions to the physics sessions, and Vol. 3 those to the instrumentation sessions. (orig.)

UCLA accelerator research ampersand development. Progress report

International Nuclear Information System (INIS)

1997-01-01

This report discusses work on advanced accelerators and beam dynamics at ANL, BNL, SLAC, UCLA and Pulse Sciences Incorporated. Discussed in this report are the following concepts: Wakefield acceleration studies; plasma lens research; high gradient rf cavities and beam dynamics studies at the Brookhaven accelerator test facility; rf pulse compression development; and buncher systems for high gradient accelerator and relativistic klystron applications

RF linear accelerators for medical and industrial applications

CERN Document Server

Hanna, Samy

2012-01-01

This unique resource offers you a clear overview of medical and industrial accelerators. Using minimal mathematics, this book focuses on offering thorough explanations of basic concepts surrounding the operation of accelerators. you find well illustrated discussions designed to help you use accelerator-based systems in a safer, more productive, and more reliable manner.This practical book details the manufacturing process for producing accelerators for medical and industrial applications. You become knowledgeable about the commonly encountered real-world manufacturing issues and potential sources of defects which help you avoid costly production problems. From principles of operation and the role of accelerators in cancer radiation therapy, to manufacturing techniques and future trends in accelerator design and applications, this easy-to-comprehend volume quickly brings you up-to-speed with the critical concepts you need to understand for your work in the field.

Proceedings of the FNCA 2006 workshop on application of electron accelerator. Radiation processing of natural polymer

International Nuclear Information System (INIS)

Tamada, Masao; Kume, Tamikazu

2007-08-01

This workshop was co-sponsored by the Ministry of Education, Culture, Sports, Science and Technology, Japan and the Ministry of Science, Technology and Innovation, Malaysia and jointly organized by the Japan Atomic Energy Agency and the Malaysian Nuclear Agency. The main objectives of the workshop were to discuss the commercial status of radiation processing of natural polymer in the participating countries and to prepare the work plan for the Forum for Nuclear Cooperation in Asia (FNCA) activities on radiation processing of natural polymer. The workshop was attended by experts on radiation processing from China, Indonesia, Japan, Korea, Malaysia, Philippines, Thailand and Vietnam. The radiation processing of natural polymer is divided into radiation crosslinking and degradation of polysaccharides. The radiation crosslinking of polysaccharides is mainly used to prepare hydrogel for healthcare and environment. Several hydrogels were commercialized in Korea, Japan and Malaysia, respectively. Hydrogels containing chitosan and carrageenan are currently in trial in China, Indonesia, Philippines and Vietnam. Cassava hydrogel is developing in Thailand. Radiation degraded chitosan is actually used in Vietnam and China in agriculture and aquaculture, respectively. Indonesia, Philippines and Thailand are trying in laboratory and pilot scale as plant growth promoter. All manuscripts submitted by every speaker were included in the proceedings. (author)

International workshop on emittance preservation in linear colliders

International Nuclear Information System (INIS)

Urakawa, Junji; Oide, Katsunobu

1993-09-01

The extremely low emittances, which are the essential feature for any linear collider, are far beyond those of the present high-energy accelerators. Every part of the linear-collider accelerator complex is liable to blow up them to a fatal degree. Above all, the main linac is the most critical part, since it will have an unprecedented length, through which very highly populated bunches should be accelerated without a faint increase of emittances. A lot of efforts have been paid, mainly theoretically, to settle this problem at all institutes. Any convincing conclusions are not yet reached. Furthermore, there are six approaches of substantially different schemes (Tesla, DLC, JLC, NLC, VLEPP, CLIC), each requiring its own way to tackle the problem. In this workshop, many up-to-date R and D results were presented by each institute. Judging from what were discussed, we may well say that the R and D work has advanced to such a level that the different approaches are rather helping each other to reach more concrete results. (J.P.N.)

Advanced beam dynamics and diagnostics concepts for laser-plasma accelerators

International Nuclear Information System (INIS)

Dornmair, Irene

2017-05-01

Laser-Plasma Accelerators (LPAs) combine a multitude of unique features, which makes them very attractive as drivers for next generation brilliant light sources including compact X-ray free-electron lasers. They provide high accelerating gradients, thereby drastically shrinking the accelerator size, while at the same time the produced electron bunches are intrinsically as short as a few femtoseconds and carry high peak currents. LPA are subject of very active research, yet, the field currently faces the challenge of improving the beam quality, and achieving stable and well-controlled injection and acceleration. This thesis tackles this issue from three different sides. A novellongitudinal phase space diagnostics is proposed that employs the strong fields present in plasma wakefields to streak ultrashort electron bunches. This allows for a temporal resolution down to the attosecond range, enabling direct determination to the current profile and the slice energy spread, both crucial quantities for the performance of free-electron lasers. Furthermore, adiabatic matching sections at the plasma-vacuum boundary are investigated. These can drastically reduce the beam divergence and thereby relax the constraints on the subsequent beam optics. For externally injected beams, the matching sections could even provide the key technology that permits emittance conservation by increasing the matched beam size to a level achievable with currently available magnetic optics. Finally, a new method is studied that allows to modify the wakefield shape. To this end, the plasma density is periodically modulated. One possible application can be to remove the linearly correlated energy spread, or chirp, from the accelerated bunch, which is suspected of being responsible for the main part of the often large energy spread of plasma accelerated beams.

Advanced beam dynamics and diagnostics concepts for laser-plasma accelerators

Energy Technology Data Exchange (ETDEWEB)

Dornmair, Irene

2017-05-15

Laser-Plasma Accelerators (LPAs) combine a multitude of unique features, which makes them very attractive as drivers for next generation brilliant light sources including compact X-ray free-electron lasers. They provide high accelerating gradients, thereby drastically shrinking the accelerator size, while at the same time the produced electron bunches are intrinsically as short as a few femtoseconds and carry high peak currents. LPA are subject of very active research, yet, the field currently faces the challenge of improving the beam quality, and achieving stable and well-controlled injection and acceleration. This thesis tackles this issue from three different sides. A novellongitudinal phase space diagnostics is proposed that employs the strong fields present in plasma wakefields to streak ultrashort electron bunches. This allows for a temporal resolution down to the attosecond range, enabling direct determination to the current profile and the slice energy spread, both crucial quantities for the performance of free-electron lasers. Furthermore, adiabatic matching sections at the plasma-vacuum boundary are investigated. These can drastically reduce the beam divergence and thereby relax the constraints on the subsequent beam optics. For externally injected beams, the matching sections could even provide the key technology that permits emittance conservation by increasing the matched beam size to a level achievable with currently available magnetic optics. Finally, a new method is studied that allows to modify the wakefield shape. To this end, the plasma density is periodically modulated. One possible application can be to remove the linearly correlated energy spread, or chirp, from the accelerated bunch, which is suspected of being responsible for the main part of the often large energy spread of plasma accelerated beams.

WORKSHOP: Radiofrequency superconductivity

International Nuclear Information System (INIS)

Tückmantel, Joachim

1993-01-01

Full text: With superconducting radiofrequency playing a major role in the push for new machines to break fresh physics frontiers, it has become a tradition for experts and newcomers in this field from all over the world to meet every second year to hear progress reports from laboratories and to discuss common problems and possible solutions. The sixth such workshop was held from 4-8 October under the chairmanship of Ron Sundelin at the Continuous Electron Beam Accelerator Facility (CEBAF) under construction in Newport News, Virginia. With 170 participants from 14 countries including Eastern Europe and China, it reflected the growing interest in the field - looking back to 1984, when CERN was the host laboratory, the second workshop had less than 100 participants. The CEBAF meeting began with laboratory status reports, covering both high beam energy ('high beta') applications with 'spherical' cavities (as with CERN's LEP200), all using niobium as superconductor and working between 352 MHz and 3 GHz, and lower energy (low beta') applications with geometrically more complicated shapes such as quarter or half wave, split ring or spoke resonators, some using electrodeposited lead as superconductor and working around 100 MHz. During these talks it became clear that more and more laboratories have focused on routine problems, such as reliable series production and testing, running cavities with ancillaries in the machines, or building complete prototypes for projects to be approved by critical funding authorities. This contrasts with the heady days just a few years ago when - at least in the high beta community - the main objective was to explore new ideas. State-of-the-art summaries showed how at 1.3 and 3 GHz 25-30 MV/m have been reached by several laboratories using different preparation methods. Newer developments for common problems included r.f. windows, couplers, controls, and especially field emission, public enemy number one for

The NASA X-Ray Mission Concepts Study

Science.gov (United States)

Petre, Robert; Ptak, A.; Bookbinder, J.; Garcia, M.; Smith, R.; Bautz, M.; Bregman, J.; Burrows, D.; Cash, W.; Jones-Forman, C.;

Proceedings of the Santa Fe workshop on electron effects

International Nuclear Information System (INIS)

Wang, T.S.; Jason, A.

1998-01-01

The Workshop was held under the sponsorship of the Spallation Neutron Source (SNS) Project to further project understanding of the effects and cause of the presence of electrons in proton accelerators. In particular, the fast instability seen in the Los Alamos Proton Storage Ring was the major topic of discussion since it limits the particles/pulse to the LANSCE target and could have an impact on the SNS Ring. This instability is believed due to the interaction of trapped electrons in the accumulated beam, i.e., an electron-proton or e-p instability. The first day of the workshop was occupied by invited talks that included a review of e-p instability theory, an overview of PSR observations, observations at other laboratories, reviews of electron-production mechanisms, theoretical studies on the PSR instability, and design issues of the SNS ring. For the second day, the workshop was organized into three working groups: a theory and computation group, a past-experiences and proposed-experiments group, and the SNS-design-strategy group. Their charter was to summarize previous work in their respective areas and to originate a course for future progress. The results of the working groups and the workshop were summarized in a joint session during the morning of the third day. These proceedings are a simple collection of the viewgraphs used as submitted to a member of the LANL secretarial staff by speakers

Performance Confirmation for the Engineered Barrier System. Report of a Workshop

International Nuclear Information System (INIS)

Bennett, David G.

2004-08-01

As part of preparations for review of future license applications, the Swedish Nuclear Power Inspectorate (SKI) organised a workshop on the engineered barrier system for the KBS-3 concept, focused on Performance Confirmation (PC). The workshop was held during 12 - 14 May, 2004 at Oskarshamn. The main purpose of the workshop was to identify key issues relating to the demonstration of long-term safety using a system of engineered barriers. The workshop began with introductory presentations on Performance Confirmation, on monitoring, and on long-term experiments in underground research laboratories. Working groups were then convened to discuss these topics and identify questions to put to the Swedish Nuclear Fuel and Waste Management Company (SKB) the following day. On the second day, SKB made several presentations, mainly on long-term experiments conducted at the Aespoe underground research laboratory. These presentations were followed by an informal session during which the questions identified by the working groups on the first day were discussed with SKB and its representatives. This report includes the questions identified by the working groups and a summary of the workshop discussions. Extended abstracts for the introductory presentations are included in an appendix. The conclusions and viewpoints presented in this report are those of one or several workshop participants. They do not necessarily coincide with those of SKI

Proceedings of workshop on K-decay experiments

International Nuclear Information System (INIS)

Nakai, Kozi

1989-08-01

The elementary particle experiment using the 12 GeV proton synchrotron in the National Laboratory for High Energy Physics (KEK) develops centering around the large scale experiment on K-meson decay. In this case, the ideal precision physics is pursued, and efforts have been exerted to improve the experimental techniques. At present the experiment on searching for rare K-decay is advancing. Next, the experiment on searching for CP nonconservation process will be begun. However, these experiments are in severe competition with those in BNL and Fermilab which have powerful accelerators, therefore it is desirable to grasp well the development of the international research plans. Therefore, in order to obtain the quideline for the experimental plan using the KEK proton synchrotron hereafter, the workshop on K-decay was held on July 11∼12, 1989. In this workshop, Arisaka (UCLA), Numao (TRIUMF) and Yamanaka (Fermilab) returned from USA and lectured on the present status of the experiment and the future perspective. The impression of the planner of the proton synchrotron experiment plan on the experiments are recorded. (K.I.)

ECFA workshop on LEP 200. Vol. 1 and 2

International Nuclear Information System (INIS)

Boehm, A.; Hoogland, W.

1987-01-01

On the initiative of the European Committee for Future Accelerators, a workshop was organized to study experimental and theoretical aspects of the physics feasible at LEP with the beam energy increased to its design value of 100 GeV per beam. These two volumes provide the written versions of the reports presented by nine working groups to the workshop, as well as the presentations on the machine upgrade itself and the potential of hadron colliders and of HERA for LEP 200 physics. Each working group studied a specific topic, evaluating in some detail the requirements both for the detectors and for the machine of W mass measurements, W decay properties, W production dynamics, electroweak radiative corrections, two-photon physics, new heavy quarks and leptons, Higgs particles, supersymmetric particles, and composite models. The proceedings also include some of the more detailed work done in the framework of the working groups. (orig.)

Outline of FNCA project on application of electron accelerator

International Nuclear Information System (INIS)

Kume, Tamikazu

2005-01-01

FNCA (Forum for Nuclear Cooperation in Asia) activities in the field of electron accelerator applications are reported. The paper mainly reports on the achievement of the 3rd workshop to discuss status of utilization of electron accelerator for thin films/hydrogel in the FNCA participating countries, China, Indonesia, Japan, Korea, Malaysia, Philippines, Thailand, and Vietnam, held in August, 2003, at Kuala Lumpur. Cross-linking of thin film from sago starch polymer blend using the Cureton (200 keV, 20 mA) and cross-linking of hydrogel for wound dressing and CMC paste-like sheet using the medium energy (3.0 MeV, 30 mA) electron accelerator of MINT (from Malaysia) were successfully demonstrated. Efforts are being made by Vietnam, Thailand and Philippines having no electron accelerator to acquire the machine for R and D and commercial use in the near future. (S. Ohno)

PREFACE: International Workshop on Neutron Optics and Detectors (NOP&D 2013)

Science.gov (United States)

2014-07-01

Every two-three years scientists involved in developments of neutron optics gather together for the International Workshop on Neutron Optics (NOP). Neutron optics has always been considered very important for the development of new neutron instrumentation. The limited brilliance of existing or future neutron sources requires the more effective usage of emitted neutrons. Indeed, improvements of the neutron optical system or an optimization of the neutron-optical tracts of instruments can result in a significant enhancement of their performance. This is especially important at present when the neutron scattering community is strongly engaged in developments of new instrumentation around the spallation neutron sources - SNS, ESS, J-PARC and Second Target Station at ISIS. In 2013 the workshop was organized by the Jülich Centre for Neutron Science of the Forschungszentrum Jülich GmbH and was held at the Conference Centre in Ismaning next to Munich on July 2-7, 2013 on the eve of the ICNS-2013 in Edinburg. It carried on the series of Neutron Optics workshops held in Villigen (1999, 2007), Tokyo (2004) and Alpe d'Huez (2010). This time it is also aimed to compliment the International Conference on Neutron Scattering in Edinburgh (ICNS-2013) by providing a platform for detailed discussions on the latest developments in the field of neutron optics. The scope of the workshop was extended to the neutron detectors (in a way similar to the NOP-2004 held in Tokyo) and was labelled as the International Workshop on Neutron Optics and Detectors, NOP&D-2013. However, in contrast to the Tokyo workshop, the focus of discussions was not the detector technologies (which are the subject of many dedicated meetings), rather than the use of detectors for the purpose of the design of modern instrumentation aiming to inform detector developers about real detectors requirements for new advanced instrumental concepts. The three-full-days workshop gathered a record number of participants, more

Sao Paulo pelletron accelerator: fortieth anniversary

International Nuclear Information System (INIS)

Pereira, Dirceu

2012-01-01

Full text: This year the 8MV Sao Paulo Pelletron tandem accelerator completes 40 years . This electrostatic accelerator was installed in the Sao Paulo University in 1972 , and it was the first of this model constructed the National Electrostatic Corporation with several innovations particularly with respect to the new concept of accelerator tube and the charge system. In the talk will be discussed the performance of the accelerator during all these years and the main result scientific results. (author)

Sao Paulo pelletron accelerator: fortieth anniversary

Energy Technology Data Exchange (ETDEWEB)

Pereira, Dirceu [Universidade de Sao Paulo (IF/USP), SP (Brazil). Inst. de Fisica

2012-07-01

Full text: This year the 8MV Sao Paulo Pelletron tandem accelerator completes 40 years . This electrostatic accelerator was installed in the Sao Paulo University in 1972 , and it was the first of this model constructed the National Electrostatic Corporation with several innovations particularly with respect to the new concept of accelerator tube and the charge system. In the talk will be discussed the performance of the accelerator during all these years and the main result scientific results. (author)

Workshop UNK-600 (proceedings); Materialy rabochego soveshchaniya UNK-600

Energy Technology Data Exchange (ETDEWEB)

Zajtsev, A M; Bitykov, S I [eds.

1994-12-31

Proceedings are presented of the workshop devoted to the accelerating storage complex of IHEP (UNK-600). In the first section is given the information on the present status of the UNK-600 and particle channels design and on the adopted experiment NEPTUN-A. In the papers of the second section are discussed hadron physics investigations at 600 GeV. Experiments in the neutrino and muon beams are analyzed. A possible program of studying the charged kaon rare decays is described.

Electromagnetic compression gun for hypervelocity projectile acceleration

International Nuclear Information System (INIS)

Woo, J.T.

1987-01-01

The rapid acceleration of projectiles to very high velocities has applications in many areas. The general requirements for an effective system is simplicity, reliability, compactness and good efficiency. The authors developed a concept by using electromagnetic forces to compressionally heat a plasma to high temperature and pressure to serve as the propellant for the acceleration of projectiles. The concept shares the simplicity of the light gas gun, but because of the high temperature of the propellant, is capable of significantly higher performance. Unlike the electrothermal gun approach to raise the propellant temperature by resistive heating, the electromagnetic concept is more efficient at higher temperatures. Operationally, the concept resembles a railgun in requiring a large pulsed current to drive the system. However, the current flow in this case is entirely external to the gun barrel and is axisymmetric. Therefore, many of the problems associated with railgun operations are avoided. Furthermore, because the current channel is external, there is also greater flexibility in the choice of load impedance to match to the power supply. The concept can also be generalized to a multi-stage regenerative system driven by a pulse forming network to resemble a coaxial accelerator

Transverse particle acceleration techniques using lasers and masers

International Nuclear Information System (INIS)

Schoen, N.C.

1983-01-01

The concept discussed herein uses an intense traveling electromagnetic wave, produced by a laser or maser source, to accelerate electrons in the Rayleigh region of a focused beam. Although the possibility of non-synchronous acceleration has been considered, very little analysis of potential device configurations has been reported. Computer simulations of the acceleration process indicate practical figure of merit values in the range of 100 MeV/m for achievable electric field strengths with current technology. The development of compact, high energy electron accelerators will provide an essential component for many new technologies. Such as high power free electron lasers, X-ray and VUV sources, and high power millimeter and microwave devices. Considerable effort has been directed toward studies of new concepts for electron acceleration, including inverse free electron lasers, GYRACS, and modified betatrons

Introduction to RF linear accelerators

International Nuclear Information System (INIS)

Weiss, M.

1994-01-01

The basic features of RF linear accelerators are described. The concept of the 'loaded cavity', essential for the synchronism wave-particle, is introduced, and formulae describing the action of electromagnetic fields on the beam are given. The treatment of intense beams is mentioned, and various existing linear accelerators are presented as examples. (orig.)

A Critical Theory Perspective on Accelerated Learning.

Science.gov (United States)

Brookfield, Stephen D.

2003-01-01

Critically analyzes accelerated learning using concepts from Herbert Marcuse (rebellious subjectivity) and Erich Fromm (automaton conformity). Concludes that, by providing distance and separation, accelerated learning has more potential to stimulate critical autonomous thought. (SK)

Second advanced ICFA beam dynamics workshop on aperture-related limitations of the performance and beam lifetime in storage rings

International Nuclear Information System (INIS)

Hagel, J.; Keil, E.

1988-01-01

These proceedings contain the papers presented at the 'Second advanced beam dynamics workshop on aperture-related limitations of the performance and beam lifetime in storage rings', which was organized in Lugano, Switzerland, from 11 to 16 April 1988, by the Beam Dynamics Panel of the International Committee for Future Accelerators (ICFA). The papers cover experiments on existing accelerators, analytical methods for determining amplitude limitations, criteria for the properties of the circulating beam and for the quality of accelerator components, and compensation schemes for field defects. (orig.)

Proceedings of the DAE-BRNS workshop on superconductivity and its application in electrical systems: abstracts

International Nuclear Information System (INIS)

2015-01-01

This workshop aims to provide an opportunity for young scientists and researchers to interact with eminent scientists and specialists working in frontier areas of science and technology of superconductivity, superconducting cable developments, superconducting magnets, superconducting radio frequency cavity for particle accelerators, power applications and detectors using superconductor. Superconductivity plays an important role in modern scientific applications starting from modern accelerators to medical diagnostics. It has great potential in future electrical systems to minimize losses and increase efficiency in the system. Papers relevant to INIS are indexed separately

Accelerator R and D: Research for Science - Science for Society

International Nuclear Information System (INIS)

Holtkamp, N.R.; Biedron, S.; Milton, S.V.; Boeh, L.; Clayton, J.E.; Zdasiuk, G.; Gourlay, S.A.; Zisman, M.S.; Hamm, R.W.; Henderson, S.; Hoffstaetter, G.H.; Merminga, L.; Ozaki, S.; Pilat, F.C.; White, M.

2012-01-01

In September 2011 the US Senate Appropriations Committee requested a ten-year strategic plan from the Department of Energy (DOE) that would describe how accelerator R and D today could advance applications directly relevant to society. Based on the 2009 workshop 'Accelerators for America's Future' an assessment was made on how accelerator technology developed by the nation's laboratories and universities could directly translate into a competitive strength for industrial partners and a variety of government agencies in the research, defense and national security sectors. The Office of High Energy Physics, traditionally the steward for advanced accelerator R and D within DOE, commissioned a task force under its auspices to generate and compile ideas on how best to implement strategies that would help fulfill the needs of industry and other agencies, while maintaining focus on its core mission of fundamental science investigation.

A New Concept of Controller for Accelerators' Magnet Power Supplies

Science.gov (United States)

Visintini, Roberto; Cleva, Stefano; Cautero, Marco; Ciesla, Tomasz

2016-04-01

The complexity of a particle accelerator implies the remote control of very large numbers of devices, with many different typologies, either distributed along the accelerator or concentrated in locations, often far away from each other. Local and global control systems handle the devices through dedicated communication channels and interfaces. Each controlled device is practically a “smart node” performing a specific task. In addition, very often, those tasks are managed in real-time mode. The performances required to the control interface has an influence on the cost of the distributed nodes as well as on their hardware and software implementation. In large facilities (e.g. CERN) the “smart nodes” derive from specific in-house developments. Alternatively, it is possible to find on the market commercial devices, whose performances (and prices) are spread over a broad range, and spanning from proprietary design (customizable to the user's needs) to open source/design. In this paper, we will describe some applications of smart nodes in the particle accelerators field, with special focus on the power supplies for magnets. In modern accelerators, in fact, magnets and their associated power supplies constitute systems distributed along the accelerator itself, and strongly interfaced with the remote control system as well as with more specific (and often more demanding) orbit/trajectory feedback systems. We will give examples of actual systems, installed and operational on two light sources, Elettra and FERMI, located in the Elettra Research Center in Trieste, Italy.

A laser plasma beatwave accelerator experiment

International Nuclear Information System (INIS)

Ebrahim, N.A.

1987-03-01

An experiment to test the laser plasma beatware accelerator concept is outlined. A heuristic estimate of the relevant experimental parameters is obtained from fluid theory and considerations of wave-particle interactions. Acceleration of 10 MeV electrons to approximately 70 MeV over a plasma length of 3 cm appears to be feasible. This corresponds to an accelerating gradient of approximately 2.5 GeV/m

Creating Fantastic PI Workshops

Energy Technology Data Exchange (ETDEWEB)

Biedermann, Laura B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Clark, Blythe G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Colbert, Rachel S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dagel, Amber Lynn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gupta, Vipin P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hibbs, Michael R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Perkins, David Nikolaus [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); West, Roger Derek [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-10-01

The goal of this SAND report is to provide guidance for other groups hosting workshops and peerto-peer learning events at Sandia. Thus this SAND report provides detail about our team structure, how we brainstormed workshop topics and developed the workshop structure. A Workshop “Nuts and Bolts” section provides our timeline and check-list for workshop activities. The survey section provides examples of the questions we asked and how we adapted the workshop in response to the feedback.

Japanese contributions to IAEA INTOR Workshop, Phase Two A, Part 3

International Nuclear Information System (INIS)

Mori, Shigeru; Tomabechi, Ken; Fujisawa, Noboru

1988-02-01

This report corresponds to Chapter I and II of Japanese contribution report to IAEA INTOR Workshop, Phase Two A, Part 3. The major objectives of the INTOR Workshop Part 3 are to evaluate innovative ideas which would significantly improve the tokamak concept, to study new-selected critical technical issues, that affect the feasibility or practicability of the INTOR concept, to assess scientific and technical data bases, and to conduct critical analyses of the existing INTOR-like designs with the aim of preparing a useful information base for future design work for ITER. To perform the innovations, critical issues, and data base, the following six groups are organized; (A) Impurity control, (B) Operational limits and confinement, (C) Current drive and heating, (D) Electromagnetics, (E) Configuration and maintenance, (F) Blanket and first wall. In addition to those groups, the two disciplinary groups are also organized to do the critical analyses of the existing INTOR-like designs; (G) Physics and (H) Engineering. (author)

In retrospect. 7th workshop RCA; Nachlese. 7. Workshop RCA. Conference report

Energy Technology Data Exchange (ETDEWEB)

Knappik, Reinhard [Verein fuer Kernverfahrenstechnik und Analytik Rossendorf e.V. (VKTA), Dresden-Rossendorf (Germany). Programmausschuss Workshop RCA

2013-08-15

The 7th Workshop RCA with 27 lectures and 12 poster presentation took place on 10 and 11 June 2013 in Dresden-Rossendorf. The traditional German event brought over 90 participants together from Germany, Austria, France, Switzerland and the Netherlands. This time the workshop put forward a special subject for the first time ('Obstacles and pitfalls when characterising waste packages'). A remarkable range of contributions was presented, which demonstrated the diversity and the problems of this subject matter. Medium to low radioactive waste and their final disposal was discussed. Other topics were the upcoming approval of recycling materials according to paragraph 29 StrlSchV as well as those from NORM (Naturally Occurring Radioactive Materials) regarding radionuclide analytics, the range of matrices to be processed and the practical problems this causes. Although the radiological feature was the central focus, other material aspects were dealt with, above all the approval of recycling materials when nuclear power plants are dismantled, but also in research institutes, which is demanding more and more attention. The lectures by Jessica Riemer (GSI Darmstadt) on the topic 'Waste material management of a research centre with heavy ion accelerators' and Elvira Mesalic (TU Munich) on 'Determining the activity inventory of bituminized old wastes' as well as the poster by Sina Brockmann on the 'Locally resolved analysis or uranium species using a couple systems of CLSM and LIFS' were awarded prizes for being outstanding presentations. (orig.)

Workshop on establishing institutional credibility for SEAB Task Force on Radioactive Waste Management

International Nuclear Information System (INIS)

1994-01-01

At the request of the Secretary of Energy Advisory Board's Task Force on Civilian Radioactive Waste Management, the National Research Council sponsored a workshop on Establishing Institutional Credibility. The purpose of the workshop was to (1) identify the range of available knowledge regarding the theoretical and conceptual issues of how institutions establish their credibility and legitimacy with key constituents, and (2) to help explore and clarify fundamental concepts in management theory related to these issues. The examination was to include what is known about how organizations establish, maintain, lose, and regain public trust and confidence. There was to be no attempt to develop consensus on these issues or to suggest particular courses of action. The workshop was held on October 24-25, 1991, in Denver, Colorado

Proceedings of the fourth workshop on elementary-particle picture of the universe

International Nuclear Information System (INIS)

Hikasa, Ken-ichi; Nakamura, Takashi; Ohshima, Takayoshi; Suzuki, Atsuo

1990-01-01

The Fourth Workshop on Elementary-Particle Picture of the Universe was held at Tateyama National Rest House from November 22 to 25, 1989. The main purpose of this workshop focuses on most of current experimental and theoretical activities in non-accelerator particle physics and astrophysics. It is also aimed to promote effective collaborations between experimentalists and theorists in these fields. The solar neutrino problem and the dark matter problem are the most exciting subjects in the astroparticle physics. They threw some doubts on the standard theories of astrophysics and also particle physics. We picked up both problems in this workshop as main themes, and discussed what they are at present and how they can be solved. Cosmology gives stringent constraints on particle properties which are frequently plausible candidates to solve the astrophysical problems. However, it is scarce to argue about how to determine the cosmological parameters and their ambiguities. We had some talks for this subject given by astronomers. New experimental results and detector developments were also presented. The atmosphere of workshop was informal, and there were extensive discussions on the above subjects. We got the confirm response that experimental and theoretical research activities in astroparticle physics were increasing here in Japan. (J.P.N.)

Asia-Pacific POPIN workshop on Internet.

Science.gov (United States)

1996-01-01

This brief article announces the accomplishments of the ESCAP Population Division of the Department of Economic and Social Information and Policy Analysis (DESIPA) in conjunction with the Asia-Pacific POPIN Internet (Information Superhighway) Training Workshop in popularizing useful new computer information technologies. A successful workshop was held in Bangkok in November 1996 for 18 people from 8 countries in the Asian and Pacific region, many of whom were from population information centers. Participants were taught some techniques for disseminating population data and information through use of the Internet computer facility. Participants learned 1) how to use Windows software in the ESCAP local area network (LAN), 2) about concepts such as HTML (hypertext mark-up language), and 3) detailed information about computer language. Computer practices involved "surfing the Net (Internet)" and linking with the global POPIN site on the Internet. Participants learned about computer programs for information handling and learned how to prepare documents using HTML, how to mount information on the World Wide Web (WWW) of the Internet, how to convert existing documents into "HTML-style" files, and how to scan graphics, such as logos, photographs, and maps, for visual display on the Internet. The Workshop and the three training modules was funded by the UN Population Fund (UNFPA). The POPIN Coordinator was pleased that competency was accomplished in such a short period of time.

Review of the conclusions of the 1996 workshop on safety culture, in Forsmark, Sweden

Energy Technology Data Exchange (ETDEWEB)

Eckered, T [PROMENT LTD (Sweden)

1997-09-01

The IAEA/SiP Senior Managers Workshop on International Promotion of Safety Culture for the NPPs with RBMK reactors was organized by IAEA and the Swedish International Project Nuclear Safety (SiP). It took place at the Forsmark NPP, Sweden, from 1 to 4 October 1996. The objective of the workshop were to provide a forum managers to exchange national and international experience on factors influencing safety culture, to better understand these factors and to further enhance promotion of safety culture. The Workshop participants started work by agreeing to seek the answers to the following three questions: 1. What constitutes a good Safety Culture? 2. What is good and bad in our own countries and plants from a Safety Culture point of view? 3. Where can we find advice and help from our colleagues to improve our own Safety Culture? This was the first workshop specifically addressing Safety Culture in RBMK countries. The aim was therefore not to produce good practices, but to lay a foundation for further work and development. A follow-up workshop should deepen the understanding of the SC concept and address specific SC matters identified at this Workshop.

Review of the conclusions of the 1996 workshop on safety culture, in Forsmark, Sweden

International Nuclear Information System (INIS)

Eckered, T.

1997-01-01

The IAEA/SiP Senior Managers Workshop on International Promotion of Safety Culture for the NPPs with RBMK reactors was organized by IAEA and the Swedish International Project Nuclear Safety (SiP). It took place at the Forsmark NPP, Sweden, from 1 to 4 October 1996. The objective of the workshop were to provide a forum managers to exchange national and international experience on factors influencing safety culture, to better understand these factors and to further enhance promotion of safety culture. The Workshop participants started work by agreeing to seek the answers to the following three questions: 1. What constitutes a good Safety Culture? 2. What is good and bad in our own countries and plants from a Safety Culture point of view? 3. Where can we find advice and help from our colleagues to improve our own Safety Culture? This was the first workshop specifically addressing Safety Culture in RBMK countries. The aim was therefore not to produce good practices, but to lay a foundation for further work and development. A follow-up workshop should deepen the understanding of the SC concept and address specific SC matters identified at this Workshop

Report of the Working Group on Far Field Accelerators

International Nuclear Information System (INIS)

Cha-Mei Tang

1992-01-01

This report describes the accomplishments of the Working Group on Far Field Accelerators. In addition to hearing presentations of current research, the group produced designs for ''100 MeV'' demonstration accelerators, ''1 GeV'' conceptual accelerators and a small electron beam source. Two of the ''100 MeV'' designs, an Inverse Free Electron Laser (IFEL) and an Inverse Cerenkov Accelerator (ICA), use the CO 2 laser and the 50 MeV linac at the Advanced Test Facility (ATF) at Brookhaven National Laboratory (BNL), requiring only modest changes in the current experimental setups. By upgrading the laser, an ICA design demonstrated 1 GeV acceleration in a gas cell about 50 cm in length. For high average power accelerators, examples based on the IFEL concept were also produced utilizing accelerators driven by high average power FELs. The Working Group also designed a small electron beam source based on the inverse electron cyclotron resonance concept. Accelerators based on the IFEL and ICA may be the first to achieve ''100 MeV'' and ''1 GeV'' energy gain demonstration with high accelerating gradients

Material Identification Technology (MIT) concept technical feasibility study

International Nuclear Information System (INIS)

Jones, J.L.; Harker, Y.D.; Yoon, W.Y.; Johnson, L.O.

1993-09-01

The Idaho National Engineering Laboratory (INEL) has initiated the design and development of a novel pulsed accelerator-based, active interrogation concept. The proposed concept, referred to as the Material Identification Technology (MIT), enables rapid (between accelerator pulses), non-destructive, elemental composition analysis of both nuclear and non-nuclear materials. Applications of this technique include material monitoring in support of counter-proliferation activities, such as export controls (at domestic and international inspection locations), SNM controls, nuclear weapon dismantlement, and chemical weapon verification. Material Identification Technology combines a pulsed, X-ray source (an electron accelerator) and a gamma detection system. The accelerator must maximize neutron production (pulse width, beam current, beam energy, and repetition rate) and minimize photon dose to the object. Current available accelerator technology can meet these requirements. The detection system must include detectors which provide adequate gamma energy resolution capability, rapid recovery after the initial X-ray interrogation pulse, and multiple single gamma event detection between accelerator pulses. Further research is required to develop the detection system. This report provides the initial feasibility assessment of the MIT concept

GRAN SASSO: Reaching the parts that accelerators cannot reach

International Nuclear Information System (INIS)

Anon.

1995-01-01

With most of the current experiments at Italy's Gran Sasso Laboratory now well underway, a workshop held earlier this year looked to the future. Gran Sasso was established in the late 1980s to study low rate processes where the laboratory's 1400 metre rock overburden and low natural radioactivity provide an ideal environment. Since then, it has become a major research centre, hosting several international collaborations. The workshop devoted half a day each to four key areas of underground physics, and clearly showed how the non-accelerator approach complements today's accelerator physics achievements. Solar neutrino physics is one of Gran Sasso's main activities, with the Gallex detector half filling one of the laboratory's three experimental halls. Gallex has already made important measurements of the solar neutrino flux, providing first evidence for the proton-proton fusion mechanism which is the solar powerhouse. The next generation experiment, Borexino, will go one step further, measuring the energy distribution of solar neutrinos as well as their flux. The experiment will also be sensitive to neutrino oscillations through its ability to pick out muon and tau neutrinos. Borexino uses boron instead of gallium as the active medium, and is currently in the trial phase. Benchmarking tests with the counter test facility (CTF) have already demonstrated the experiment's feasibility, paving the way for full scale construction. Further ideas for future detectors based on several different active media were also discussed, and a proposal for a helium TPC detector, HELLAZ, was presented. With a threshold of around 240 keV, comparable to that of Gallex and Borexino, HELLAZ would give another handle on neutrinos from the proton-proton reaction, the most abundant source of solar neutrinos. Neutrinoless double beta decay, dark matter searches, and certain low rate processes in nuclear physics all require the quiet, low radiation surroundings

Proceedings of the Fifth AASPP Workshop on Asian Nuclear Reaction Database Development

International Nuclear Information System (INIS)

Saxena, Alok

2015-02-01

The Fifth AASPP Workshop on Asian Nuclear Reaction Database Development was organized by Nuclear Data Physics Centre of India in cooperation with the IAEA and the Board of Research in Nuclear Sciences, Department of Atomic Energy from 22-24 Sept., 2014 at Bhabha Atomic Research Centre, Mumbai, India. Over seventy participants took part in the workshop representing India, Japan, Republic of Korea, Vietnam, Kazakhstan, Uzbekistan, Mongolia and a representative from the IAEA. The workshop covered the overview of nuclear data activities in different countries and covered the topics related to experiments performed using various facilities, the upcoming and existing accelerators and experimental facilities, EXFOR compilation activities, reactor sensitivity studies to nuclear data, criticality benchmarking studies, nuclear data requirement of nuclear power reactors, theoretical calculations using various codes, and covariances in nuclear data. About thirty five talks were delivered by participants from various countries on these topics. The concluding session had a panel discussion on possible future collaboration involving participants from different countries. The present report gives summary of each presentation. (author)

Canadian Hydrogen Association workshop on building Canadian strength with hydrogen systems. Proceedings

International Nuclear Information System (INIS)

2006-01-01

The Canadian Hydrogen Association workshop on 'Building Canadian Strength with Hydrogen Systems' was held in Montreal, Quebec, Canada on October 19-20, 2006. Over 100 delegates attended the workshop and there were over 50 presentations made. The Canadian Hydrogen Association (CHA) promotes the development of a hydrogen infrastructure and the commercialization of new, efficient and economic methods that accelerate the adoption of hydrogen technologies that will eventually replace fossil-based energy systems to reduce greenhouse gas emissions. This workshop focused on defining the strategic direction of research and development that will define the future of hydrogen related energy developments across Canada. It provided a forum to strengthen the research, development and innovation linkages among government, industry and academia to build Canadian strength with hydrogen systems. The presentations described new technologies and the companies that are making small scale hydrogen and hydrogen powered vehicles. Other topics of discussion included storage issues, hydrogen safety, competition in the hydrogen market, hydrogen fuel cell opportunities, nuclear-based hydrogen production, and environmental impacts

Summary of the ECLOUD'04 Workshop

International Nuclear Information System (INIS)

Macek, R.; Furman, M.

2004-01-01

The 31st ICFA Advanced Beam Dynamics Workshop on Electron-Cloud Effects ''ECLOUD'04'' was held April 19-23, 2004 at Napa, CA, USA. A broad range of current topics in this field were illuminated by 53 talks in 7 sessions plus 6 session summaries at the final summary session. These covered a variety of experimental methods and results, along with progress on understanding of the topic obtained from simulations and analytic theory, and evaluations of the effectiveness of various methods/mechanisms for mitigation of the adverse impact on accelerator performance. In addition, a panel discussion was held on ''Future Needs and Future Directions''. A summary of progress on the major themes covered at ECLOUD'04 is presented

The evolution of high energy accelerators

International Nuclear Information System (INIS)

Courant, E.D.

1994-01-01

Accelerators have been devised and built for two reasons: In the first place, by physicists who needed high energy particles in order to have a means to explore the interactions between particles that probe the fundamental elementary forces of nature. And conversely, sometimes accelerator builders produce new machines for higher energy than ever before just because it can be done, and then challenge potential users to make new discoveries with the new means at hand. These two approaches or motivations have gone hand in hand. This lecture traces how high energy particle accelerators have grown from tools used for esoteric small-scale experiments to the gigantic projects of today. So far all the really high-energy machines built and planned in the world--except the SLC--have been ring accelerators and storage rings using the strong-focusing method. But this method has not removed the energy limit, it has only pushed it higher. It would seem unlikely that one can go beyond the Large Hadron Collider (LHC)--but in fact a workshop was held in Sicily in November 1991, concerned with the question of extrapolating to 100 TeV. Other acceleration and beam-forming methods are now being discussed--collective fields, laser acceleration, wake-field accelerators etc., all aimed primarily at making linear colliders possible and more attractive than with present radiofrequency methods. So far it is not entirely clear which of these schemes will dominate particle physics in the future--maybe something that has not been thought of as yet

Workshops as a Research Methodology

Science.gov (United States)

Ørngreen, Rikke; Levinsen, Karin

2017-01-01

This paper contributes to knowledge on workshops as a research methodology, and specifically on how such workshops pertain to e-learning. A literature review illustrated that workshops are discussed according to three different perspectives: workshops as a means, workshops as practice, and workshops as a research methodology. Focusing primarily on…

A Workshop for High School Students on Naive Set Theory

Science.gov (United States)

Wegner, Sven-Ake

2014-01-01

In this article we present the prototype of a workshop on naive set theory designed for high school students in or around the seventh year of primary education. Our concept is based on two events which the author organized in 2006 and 2010 for students of elementary school and high school, respectively. The article also includes a practice report…

Impact of a personal CYP2D6 testing workshop on physician assistant student attitudes toward pharmacogenetics.

Science.gov (United States)

O'Brien, Travis J; LeLacheur, Susan; Ward, Caitlin; Lee, Norman H; Callier, Shawneequa; Harralson, Arthur F

2016-03-01

We assessed the impact of personal CYP2D6 testing on physician assistant student competency in, and attitudes toward, pharmacogenetics (PGx). Buccal samples were genotyped for CYP2D6 polymorphisms. Results were discussed during a 3-h PGx workshop. PGx knowledge was assessed by pre- and post-tests. Focus groups assessed the impact of the workshop on attitudes toward the clinical utility of PGx. Both student knowledge of PGx, and its perceived clinical utility, increased immediately following the workshop. However, exposure to PGx on clinical rotations following the workshop seemed to influence student attitudes toward PGx utility. Personal CYP2D6 testing improves both knowledge and comfort with PGx. Continued exposure to PGx concepts is important for transfer of learning.

5th report from the LHC performance workshop

CERN Multimedia

Bulletin's correspondent from Chamonix

2012-01-01

The morning session on Friday 10 February - the final day of the workshop - saw further examination of the challenges of the High Luminosity LHC and included a look at the state of R&D for the new magnets required for the high luminosity interaction regions. There was then an entertaining look at even more distant future. Possible future projects under consideration include the Large Hadron electron Collider (LHeC) which foresees colliding 60 GeV electrons with 7 TeV protons, and the High Energy LHC (HE-LHC) in which the beam energy of the LHC is increased from 7 to 16.5 TeV. Serious technological challenges exist for both these options. In the afternoon Steve Myers, CERN's Director for Accelerators and Technology, presented a summary of the workshop recommendations. In brief, the LHC should operate at 4 TeV in 2012 with the key priorities being: delivering enough luminosity to ATLAS and CMS to allow them to independently discover or exclude the Higgs; the proton-Lead ion run; and machine deve...

Proceedings of workshop on 'future in HEP computing'

International Nuclear Information System (INIS)

Karita, Yukio; Amako, Katsuya; Watase, Yoshiyuki

1993-12-01

The workshop was held on March 11 and 12, 1993, at the National Laboratory for High Energy Physics (KEK). The large flow from the conventional system centering around large versatile computers to the down-sizing taking distributed processing systems in it is formed, but its destination is not yet seen. As the concrete themes of 'future in HEP computing', problems toward down-sizing and the approach, future perspective of the networks, and adaptation of software engineering and pointing to object were taken up. At the workshop, lectures were given on requirements in HEP computing, possible solutions from Hitachi and Fujitsu, and network computing with work-stations regarding down-sizing and HEP computing; approaches in INS and KEK regarding future computing system in HEP laboratories; user requirement for future network, network service available in 1995-2005, multi-media communication and network protocols regarding future networks; object-oriented approach for software development, OOP for real time data acquisition and accelerator control; ProdiG activities and future of FORTRAN, F90 and HPF regarding OOP and physics, and trends in software development methodology. (K.I.)

Human genetics for non-scientists: Practical workshops for policy makers and opinion leaders

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

These workshops form part of a series of workshops that the Banbury and the DNA Learning Centers of Cold Spring Harbor Laboratory have held for a number of years, introducing genetics, and the ways in which scientific research is done, to non-scientists. The purpose of the workshops as stated in the grant application was: {open_quotes}Our objective is to foster a better understanding of the societal impact of human genome research by providing basic information on genetics to non-scientists whose professions or special interests interface with genetic technology.... Participants will be chosen for their interest in human genetics and for their roles as opinion leaders in their own communities. Primary care physicians are of particular interest to us for this series of workshops.{close_quotes} Two workshops were held under this grant. The first was held in 21-24 April, 1994 and attended by 20 participants, and the second was held 16-19 November, 1995, and attended by 16 participants. In each case, there was a combination of concept lectures on the foundations of human molecular genetics; lectures by invited specialists; and laboratory experiments to introduce non-scientists to the techniques used in molecular genetics.

Proceedings of the workshop on physics at future accelerators

International Nuclear Information System (INIS)

1987-01-01

A workshop took place at La Thuile and at CERN in January 1987 to study the physics potential of three types of particle collider with energies in the TeV region, together with the feasibility of experiments with them. The machines were: A Large Hadron Collider (LHC) placed in the LEP tunnel at CERN, with a total proton-proton centre-of-mass energy of about 16 TeV; an electron-proton collider, using the LHC and LEP, with a centre-of-mass energy in the range 1.3 TeV to 1.8 TeV; and an electron-positron linear collider with centre-of-mass energy about 2 TeV. This volume of the proceedings contains summary talks given at CERN by the conveners of the study groups. They cover the possibilities for discovery of new phenomena anticipated in the energy region up to the order of a TeV in the centre of mass of colliding partons, or of the electron and positron. Also discussed are the limits of current technology in the construction of particle-detector systems suitable for use at these energies, and especially in the high event rates provided by a proton-proton collider of luminosity 10 33 cm -2 s -1 or more. (orig.)

A proposed laser wakefield acceleration experiment

International Nuclear Information System (INIS)

Ebrahim, N.A.

1995-05-01

In this report we discuss the basic concepts of a laser wakefield experiment using an ultrashort laser pulse. In particular, we obtain some heuristic estimates of experimental parameters relevant to an experiment to test the laser wakefield acceleration concept. (author). 8 refs., 2 tabs

'Workshops in healing' for senior medical students: a 5-year overview and appraisal.

Science.gov (United States)

Kearsley, John H; Lobb, Elizabeth A

2014-12-01

We report upon the design, content and feedback from an interactive, experiential series of Workshops in Healing for senior medical students. Fifty-six final year medical students enrolled in 2×3 h workshops designed around the core themes of 'physician know thyself' (Workshop 1) and 'confronting suffering' (Workshop 2). Of the 56 students who initially enrolled, 48 students completed both workshops and provided a written open-ended reflection of their learning experience. The study, undertaken over a consecutive 5-year period (2008-2012), employed an emergent, qualitative design using thematic analysis of the reflective comments. We found that the design and content of both workshops promoted transformative learning for these final year medical students. Students identified the following benefits: (1) the opportunity to reaffirm their commitment to their chosen career path; (2) the value of listening to other students share their stories; (3) the importance of the timing of the workshops to occur after exams; (4) the use of various mediums such as art, poetry, music and contemporary/classic literature to present concepts of suffering and healing; and (5) the creation of a safe and confidential space. Students reported that these innovative workshops gave them a renewed sense of drive and enthusiasm for their chosen career. They highlighted the importance of addressing an aspect of medicine (healing) not covered in the traditional medical curriculum. Workshops in Healing helped them to rediscover a deeper meaning to medicine and their roles as future healthcare professionals. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Electron-beam direct drive for rf accelerator cavities

International Nuclear Information System (INIS)

Nahemow, M.D.; Humphries, S. Jr.

1987-01-01

This paper describes a Program to Demonstrate Electron-Beam Direct Drive for Radio Frequency (RF) Linear Accelerators at the Westinghouse R and D Center. The experimental program was undertaken using an existing electron beam facility at the Westinghouse R and C Center to demonstrate the potential of the Direct Drive RF Cavities for High Power Beams concept discussed as part of a program to develop a viable alternate concept for driving RF linear accelerators

WORKSHOP: Stable particle motion

International Nuclear Information System (INIS)

Ruggiero, Alessandro G.

1993-01-01

Full text: Particle beam stability is crucial to any accelerator or collider, particularly big ones, such as Brookhaven's RHIC heavy ion collider and the larger SSC and LHC proton collider schemes. A workshop on the Stability of Particle Motion in Storage Rings held at Brookhaven in October dealt with the important issue of determining the short- and long-term stability of single particle motion in hadron storage rings and colliders, and explored new methods for ensuring it. In the quest for realistic environments, the imperfections of superconducting magnets and the effects of field modulation and noise were taken into account. The workshop was divided into three study groups: Short-Term Stability in storage rings, including chromatic and geometric effects and correction strategies; Long-Term Stability, including modulation and random noise effects and slow varying effects; and Methods for determining the stability of particle motion. The first two were run in parallel, but the third was attended by everyone. Each group considered analytical, computational and experimental methods, reviewing work done so far, comparing results and approaches and underlining outstanding issues. By resolving conflicts, it was possible to identify problems of common interest. The workshop reaffirmed the validity of methods proposed several years ago. Major breakthroughs have been in the rapid improvement of computer capacity and speed, in the development of more sophisticated mathematical packages, and in the introduction of more powerful analytic approaches. In a typical storage ring, a particle may be required to circulate for about a billion revolutions. While ten years ago it was only possible to predict accurately stability over about a thousand revolutions, it is now possible to predict over as many as one million turns. If this trend continues, in ten years it could become feasible to predict particle stability over the entire storage period. About ninety participants

The Energy Efficiency of High Intensity Proton Driver Concepts

Energy Technology Data Exchange (ETDEWEB)

Yakovlev, Vyacheslav [Fermilab; Grillenberger, Joachim [PSI, Villigen; Kim, Sang-Ho [ORNL, Oak Ridge (main); Seidel, Mike [PSI, Villigen; Yoshii, Masahito [JAEA, Ibaraki

2017-05-01

For MW class proton driver accelerators the energy efficiency is an important aspect; the talk reviews the efficiency of different accelerator concepts including s.c./n.c. linac, rapid cycling synchrotron, cyclotron; the potential of these concepts for very high beam power is discussed.

ASTOR, concept of a combined acceleration and storage ring for the production of intense pulsed or continuous beams of neutrinos, pions, muons, kaons and neutrons

International Nuclear Information System (INIS)

Joho, W.

1983-01-01

A new concept for a high intensity accelerator for 2 GeV protons using the continuous 590 MeV beam from the present ring cyclotron has been worked out at SIN. To suppress the cosmic background in neutrino experiments a pulsed beam with high peak current and low duty cycle is required. Using the so called phase expansion effect 1,2 one can combine the acceleration and storage effect in a single isochronous cyclotron ASTOR. With the help of several RF cavities, positioned at different radii, it is possible to operate ASTOR either in a pulsed mode at 1500 Hz or in a continuous mode. The anticipated beam powers are .8 MW and 4 MW respectively. The ASTOR concept is also applicable in a possible kaon factory design, acting as an interface between the SIN ring cyclotron and a 50 Hz synchrotron for 15 to 20 GeV protons

MOOC Design Workshop

DEFF Research Database (Denmark)

Nørgård, Rikke Toft; Mor, Yishay; Warburton, Steven

2016-01-01

For the last two years we have been running a series of successful MOOC design workshops. These workshops build on previous work in learning design and MOOC design patterns. The aim of these workshops is to aid practitioners in defining and conceptualising educational innovations (predominantly......, but not exclusively MOOCs) which are based on an empathic user-centered view of the target learners and teachers. In this paper, we share the main principles, patterns and resources of our workshops and present some initial results for their effectiveness...

Future Directions in Idiopathic Pulmonary Fibrosis Research. An NHLBI Workshop Report

Science.gov (United States)

Blackwell, Timothy S.; Tager, Andrew M.; Borok, Zea; Moore, Bethany B.; Schwartz, David A.; Anstrom, Kevin J.; Bar-Joseph, Ziv; Bitterman, Peter; Blackburn, Michael R.; Bradford, William; Brown, Kevin K.; Chapman, Harold A.; Collard, Harold R.; Cosgrove, Gregory P.; Deterding, Robin; Doyle, Ramona; Flaherty, Kevin R.; Garcia, Christine Kim; Hagood, James S.; Henke, Craig A.; Herzog, Erica; Hogaboam, Cory M.; Horowitz, Jeffrey C.; King, Talmadge E.; Loyd, James E.; Lawson, William E.; Marsh, Clay B.; Noble, Paul W.; Noth, Imre; Sheppard, Dean; Olsson, Julie; Ortiz, Luis A.; O’Riordan, Thomas G.; Oury, Tim D.; Raghu, Ganesh; Roman, Jesse; Sime, Patricia J.; Sisson, Thomas H.; Tschumperlin, Daniel; Violette, Shelia M.; Weaver, Timothy E.; Wells, Rebecca G.; White, Eric S.; Kaminski, Naftali; Martinez, Fernando J.; Wynn, Thomas A.; Thannickal, Victor J.

2014-01-01

The median survival of patients with idiopathic pulmonary fibrosis (IPF) continues to be approximately 3 years from the time of diagnosis, underscoring the lack of effective medical therapies for this disease. In the United States alone, approximately 40,000 patients die of this disease annually. In November 2012, the NHLBI held a workshop aimed at coordinating research efforts and accelerating the development of IPF therapies. Basic, translational, and clinical researchers gathered with representatives from the NHLBI, patient advocacy groups, pharmaceutical companies, and the U.S. Food and Drug Administration to review the current state of IPF research and identify priority areas, opportunities for collaborations, and directions for future research. The workshop was organized into groups that were tasked with assessing and making recommendations to promote progress in one of the following six critical areas of research: (1) biology of alveolar epithelial injury and aberrant repair; (2) role of extracellular matrix; (3) preclinical modeling; (4) role of inflammation and immunity; (5) genetic, epigenetic, and environmental determinants; (6) translation of discoveries into diagnostics and therapeutics. The workshop recommendations provide a basis for directing future research and strategic planning by scientific, professional, and patient communities and the NHLBI. PMID:24160862

Prospects of the surfatron laser plasma accelerator

International Nuclear Information System (INIS)

Katsouleas, T.; Joshi, C.; Mori, W.; Dawson, J.M.

1983-01-01

The surfatron concept is proposed as a possible solution to the problem of staging in the laser-plasma beat wave accelerator scheme. Prospects of a 100 GeV particle accelerator based on the surfatron concept are explored. Finite angle optical mixing appears to be a promising solution for drastically reducing the width of the plane wave, thereby, making the required laser power and the device size realizable for a proof-of-principle experiment. Our conclusions are based mainly on analytical theory and one-dimensional particle simulations

A brief history of high power RF proton linear accelerators

International Nuclear Information System (INIS)

Browne, J.C.

1996-01-01

The first mention of linear acceleration was in a paper by G. Ising in 1924 in which he postulated the acceleration of positive ions induced by spark discharges which produced electric fields in gaps between a series of open-quotes drift tubesclose quotes. Ising apparently was not able to demonstrate his concept, most likely due to the limited state of electronic devices. Ising's work was followed by a seminal paper by R. Wideroe in 1928 in which he demonstrated the first linear accelerator. Wideroe was able to accelerate sodium or potassium ions to 50 keV of energy using drift tubes connected alternately to high frequency waves and to ground. Nuclear physics during this period was interested in accelerating protons, deuterons, electrons and alpha particles and not heavy ions like sodium or potassium. To accelerate the light ions required much higher frequencies than available at that time. So linear accelerators were not pursued heavily at that time. Research continued during the 1930s but the development of high frequency RF tubes for radar applications in World War 2 opened the potential for RF linear accelerators after the war. The Berkeley laboratory of E. 0. Lawrence under the leadership of Luis Alvarez developed a new linear proton accelerator concept that utilized drift tubes that required a full RF period to pass through as compared to the earlier concepts. This development resulted in the historic Berkeley 32 MeV proton linear accelerator which incorporated the open-quotes Alvarez drift tubeclose quotes as the basic acceleration scheme using surplus 200 MHz radar components

CAS CERN Accelerator School third general accelerator physics course

International Nuclear Information System (INIS)

Turner, S.

1989-01-01

The general course on accelerator physics given in Salamanca, Spain, closely followed those organised by the CERN Accelerator School at Gif-sur-Yvette, Paris in 1984, and at Aarhus, Denmark in 1986 and whose proceedings were published as CERN Yellow Reports 85-19 (1985) and 87-10 (1987) respectively. However, certain topics were treated in a different way, improved or extended, while some new ones were introduced and it is all of these which are included in the present proceedings. The lectures include beam-cooling concepts, Liouville's theorem and emittance, emittance dilution in transfer lines, weak-betatron coupling, diagnostics, while the seminars are on positron and electron sources, linac structures and the LEP L3 experiment, together with industrial aspects of particle accelerators. Also included are errata and addenda to the Yellow Reports mentioned above. (orig.)

[Reform steps toward networking sheltered workshops and the general labour market].

Science.gov (United States)

Wendt, S

2010-02-01

Only 0.16% of disabled employees are enabled to change from sheltered workshops to the general labour market. At the same time the number of disabled employees in sheltered workshops is increasing more than anticipated. Investigations into the growing admissions to sheltered workshops resulted in recommendations to improve the practice of change over. More and more admissions of students having finished special schools could be reduced by improved cooperation between special schools and the local employment market. Special schools should offer suitable job trainings and support students to develop an understanding of the requirements of specific jobs and of their opportunities to develop their skills to do these jobs. In 2009, supported employment has been regulated in social security law, lasting up to three years and aimed at qualifying disabled youngsters for employment in the general labour market instead of entering sheltered workshops. The majority of admissions to sheltered workshops in the meantime concern people with psychological handicaps, with more than 30% however leaving the workshops later on. For this population, "virtual sheltered workshops" are offering more suitable means for reintegration in the general labour market, such as temporary employment in the general labour market or in occupations with small earnings. The personal budget for work is meant to be a model project within the German Länder, to transfer personal support from the sheltered workshop into the general labour market. The conference of German Länder Ministers of Social Affairs has been active since 2007 to develop a concept for reform of the social security law concerning integration assistance for disabled people, which in future is to concentrate on individual needs, removal of obstacles in the law to facilitate the transition from sheltered workshops into the general labour market. The "Deutsche Verein für öffentliche und private Fürsorge" (German association for public

Linear magnetic fusion: summary of Seattle workshop

International Nuclear Information System (INIS)

1977-12-01

The linear-geometry magnetic confinement concept is among the oldest used in the study of high-temperature plasmas. However, it has generally been discounted as a suitable approach for demonstrating controlled thermonuclear fusion because rapid losses from the plasma column ends necessitate very long devices. Further, the losses and how to overcome them have not yet received parametric experimental study, nor do facilities exist with which such definitive experiments could be performed. Nonetheless, the important positive attribute, simplicity, together with the appearance of several ideas for reducing end losses have provided motivation for continued research on linear magnetic fusion (LMF). These motivations led to the LMF workshop, held in Seattle, March 9--11, 1977, which explored the potential of LMF as an alternate approach to fusion. A broad range of LMF aspects were addressed, including radial and axial losses, stability and equilibrium, heating, technology, and reactor considerations. The conclusions drawn at the workshop are summarized

Design, implementation, and outcome of a hands-on arthrocentesis workshop.

Science.gov (United States)

Barilla-Labarca, Maria-Louise; Tsang, James C; Goldsmith, Melissa; Furie, Richard

2009-09-01

During a 4-week rheumatology elective at our institution, opportunities for internal medicine residents to perform arthrocentesis were limited, particularly for sites other than the knee. Consequently, residents were inadequately prepared and had less self-confidence to perform such procedures. To overcome these educational deficiencies, an arthrocentesis workshop was developed. We report our quality improvement data that was collected during the first year of workshop implementation. We devised a structured half-day arthrocentesis workshop for rheumatology fellows as well as rotating internal medicine residents. This program consisted of a one hour lecture immediately followed by a hands-on workshop that used mannequin models for 5 anatomic sites. A self-assessment questionnaire and medical knowledge test were administered before and after each session. The accuracy of the self-assessment questionnaire was analyzed by comparing responses to an external objective measure of knowledge in the same content area. Finally, an optional postworkshop survey addressed resident satisfaction. Thirty-eight trainees participated in the workshop between July 2006 and June 2007. There were statistically significant improvements in self-confidence in 9 content areas (P knowledge test during the preworkshop analysis. In contrast, the postworkshop analysis displayed modestly higher concordance. All residents completing a postworkshop survey believed that it was a useful exercise, and 96% stated that they would change their practice habits. The arthrocentesis workshop provided a solid foundation from which trainees can learn key concepts of joint injection, increase their self-confidence and refine their motor skills. The accuracy of resident self-reported confidence is poor and should therefore be used only to complement other means of competency assessment and medical knowledge acquisition.

Fokker-Planck transport in solid state accelerator concepts

International Nuclear Information System (INIS)

Newberger, B.; Tajima, T.

1989-01-01

Particle transport in a crystalline solid under channeling conditions is considered by means of a Fokker-Planck description. The model includes electron multiple scattering, radiation damping and an accelerating electric field. Analytic solutions have been obtained using a harmonic potential model to describe the channeling forces. These solutions will be described

Proceedings of standard model at the energy of present and future accelerators

International Nuclear Information System (INIS)

Csikor, F.; Pocsik, G.; Toth, E.

1992-01-01

This book contains the proceedings of the Workshop on The Standard Model at the Energy of the Present and Future Accelerators, 27 June - 1 July 1989, Budapest. The Standard Model of strong and electro-weak interactions providing essential insights into the fundamental structure of matter and being the basic building block of further generalizations has a rich content. The Workshop was devoted to discussing topical problems of testing the Standard Model in high energy reactions such as jet physics and fragmentation, new applications and tests of perturbative QCD, CP-violation, B-meson physics and developments in weak decays, some of the future experimental plans and related topics

77 FR 12313 - Food Labeling Workshop; Public Workshop

Science.gov (United States)

2012-02-29

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-N-0001] Food Labeling Workshop; Public Workshop AGENCY: Food and Drug Administration, HHS. ACTION: Notice of... District Office (DALDO), in collaboration with Oklahoma State University (OSU), Robert M. Kerr Food...

75 FR 29775 - Food Labeling Workshop; Public Workshop

Science.gov (United States)

2010-05-27

... DEPARTMENT OF HEALTH AND HUMAN SERVICES [Docket No. FDA-2010-N-0001] Food and Drug Administration Food Labeling Workshop; Public Workshop AGENCY: Food and Drug Administration, HHS. ACTION: Notice of...: Institute of Food Science & Engineering, University of Arkansas, 2650 North Young Ave., Fayetteville, AR...

On statistical acceleration convergence of double sequences

Directory of Open Access Journals (Sweden)

Bipan Hazarika

2017-04-01

Full Text Available In this article the notion of statistical acceleration convergence of double sequences in Pringsheim's sense has been introduced. We prove the decompostion theorems for  statistical acceleration convergence of double sequences and some theorems related to that concept have been established using the four dimensional matrix transformations. We provided some examples, where the results of acceleration convergence fails to hold for the statistical cases.

Systems Engineering Workshops | Wind | NREL

Science.gov (United States)

Workshops Systems Engineering Workshops The Wind Energy Systems Engineering Workshop is a biennial topics relevant to systems engineering and the wind industry. The presentations and agendas are available for all of the Systems Engineering Workshops: The 1st NREL Wind Energy Systems Engineering Workshop

IUSSP Committee on International Migration, Workshop on International Migration Systems and Networks.

Science.gov (United States)

Lim, Lin Lean

1987-01-01

This mini-workshop sought a framework for examining the dynamics of migration processes, especially the interlinkages between sending and receiving countries. These two focuses emerged as directions for further research: (1) a topology reflecting the concepts underlying international migration; and (2) empirical studies which attempt to apply the…

Ion optics for accelerators

International Nuclear Information System (INIS)

Enge, H.A.

1974-01-01

A review is given of ion-optic devices used in particle accelerators, including electrostatic lenses, magnetic quadrupoles, and deflecting magnets. Tube focusing in dc accelerators is also treated, and a novel scheme for shaping the electrodes to produce strong focusing is described. The concepts of emittance (phase space) and emittance conservation are briefly discussed. Chromatic and spatial aberrations are introduced, and it is shown how they can be calculated and sometimes substantially reduced. Some examples are given

Strategic Leaders Adapting to the Future Environment: Department of State Senior Leader Workshop. Volume 02-03

National Research Council Canada - National Science Library

Wimbish, Bill

2003-01-01

The purpose of the workshop was to provide participants an opportunity to first review and examine current strategic leadership theories and concepts and how the Army develops and trains its officer...

Applied antineutrino physics workshop

International Nuclear Information System (INIS)

Lund, James C.

2008-01-01

This workshop is the fourth one of a series that includes the Neutrino Geophysics Conference at Honolulu, Hawaii, which I attended in 2005. This workshop was organized by the Astro-Particle and Cosmology laboratory in the recently opened Condoret building of the University of Paris. More information, including copies of the presentations, on the workshop is available on the website: www.apc.univ-paris7.fr/AAP2007/. The workshop aims at opening neutrino physics to various fields such that it can be applied in geosciences, nuclear industry (reactor and spent fuel monitoring) and non-proliferation. The workshop was attended by over 60 people from Europe, USA, Asia and Brazil. The meeting was also attended by representatives of the Comprehensive nuclear-Test Ban Treaty (CTBT) and the International Atomic Energy Agency (IAEA). The workshop also included a workshop dinner on board of a river boat sailing the Seine river

Beam dynamics simulation of a double pass proton linear accelerator

Directory of Open Access Journals (Sweden)

Kilean Hwang

2017-04-01

Full Text Available A recirculating superconducting linear accelerator with the advantage of both straight and circular accelerator has been demonstrated with relativistic electron beams. The acceleration concept of a recirculating proton beam was recently proposed [J. Qiang, Nucl. Instrum. Methods Phys. Res., Sect. A 795, 77 (2015NIMAER0168-900210.1016/j.nima.2015.05.056] and is currently under study. In order to further support the concept, the beam dynamics study on a recirculating proton linear accelerator has to be carried out. In this paper, we study the feasibility of a two-pass recirculating proton linear accelerator through the direct numerical beam dynamics design optimization and the start-to-end simulation. This study shows that the two-pass simultaneous focusing without particle losses is attainable including fully 3D space-charge effects through the entire accelerator system.

Teaching Introductory Geoscience: A Cutting Edge Workshop Report

Science.gov (United States)

Manduca, C.; Tewksbury, B.; Egger, A.; MacDonald, H.; Kirk, K.

2008-12-01

Introductory undergraduate courses play a pivotal role in the geosciences. They serve as recruiting grounds for majors and future professionals, provide relevant experiences in geoscience for pre-service teachers, and offer opportunities to influence future policy makers, business people, professionals, and citizens. An introductory course is also typically the only course in geoscience that most of our students will ever take. Because the role of introductory courses is pivotal in geoscience education, a workshop on Teaching Introductory Courses in the 21st Century was held in July 2008 as part of the On the Cutting Edge faculty development program. A website was also developed in conjunction with the workshop. One of the central themes of the workshop was the importance of considering the long-term impact a course should have on students. Ideally, courses can be designed with this impact in mind. Approaches include using the local geology to focus the course and illustrate concepts; designing a course for particular audience (such as Geology for Engineers); creating course features that help students understand and interpret geoscience in the news; and developing capstone projects to teach critical thinking and problem solving skills in a geologic context. Workshop participants also explored strategies for designing engaging activities including exploring with Google Earth, using real-world scenarios, connecting with popular media, or making use of campus features on local field trips. In addition, introductory courses can emphasize broad skills such as teaching the process of science, using quantitative reasoning and developing communication skills. Materials from the workshop as well as descriptions of more than 150 introductory courses and 350 introductory-level activities are available on the website: http://serc.carleton.edu/NAGTWorkshops/intro/index.html.

Proceedings of the 5th US/German Workshop on Salt Repository Research Design and Operation

Energy Technology Data Exchange (ETDEWEB)

Hansen, Francis D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Leigh, Christi [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stein, Walter [Karlsruhe Inst. of Technology (KIT) (Germany); Bollingerfehr, Wilhelm [DBE Technology, Peine (Germany); Von Berlepsche, Thilo [DBE Technology, Peine (Germany)

2015-01-01

The 5th US/German Workshop on Salt Repository Research, Design, and Operation was held in Santa Fe New Mexico September 8-10, 2014. The forty seven registered participants were equally divided between the United States (US) and Germany, with one participant from The Netherlands. The agenda for the 2014 workshop was under development immediately upon finishing the 4th Workshop. Ongoing, fundamental topics such as thermomechanical behavior of salt, plugging and sealing, the safety case, and performance assessment continue to advance the basis for disposal of heat-generating nuclear waste in salt formations. The utility of a salt underground research laboratory (URL) remains an intriguing concept engendering discussion of testing protocol. By far the most interest in this years’ workshop pertained to operational safety. Given events at the Waste Isolation Pilot Plant (WIPP), this discussion took on a new sense of relevance and urgency.

Proceedings of the 3rd workshop on ion-beam-applied biology

International Nuclear Information System (INIS)