WorldWideScience

Sample records for abwasserreinigung als beitrag

  1. Waste water cleaning in high-performance bioreactors; Abwasserreinigung in Hochleistungsbioreaktoren

    Energy Technology Data Exchange (ETDEWEB)

    Holler, S.; Sternad, W.; Troesch, W. [Fraunhofer-Institut fuer Grenzflaechen- und Bioverfahrenstechnik (IGB), Stuttgart (Germany)

    1999-07-01

    Cleaning of municipal sewage in bioreactors with biomass retention constitutes a modern and sustainable way of cleaning sewage. Contrary to conventional aerated sludge techniques, such systems achieve high productivity at high biomass concentrations. Reactor volume can be kept low, and short retention times are realized. It is shown that a loop reactor in combination with a crossflow microfiltration unit constitutes an appropriate system to meet future demands on sewage cleaning. Such a system can realize a COD turnover of 95 % at retention times of 0.5 hours. Crossflow microfiltration can set the concentration of biomass in the bioreactor to up to 30 grammes of dry substance per litre. (orig.) [German] Die Reinigung kommunaler Abwaesser in Bioreaktoren mit Biomasserueckhaltung stellt ein modernes und nachhaltiges Verfahren zur Abwasserreinigung dar. Im Gegensatz zu konventionellen Belebungsverfahren laesst sich in einem solchen System bei hohen Biomassekonzentrationen eine hohe Produktivitaet erreichen. Das Reaktorvolumen kann gering gehalten werden, und kurze Verweilzeiten koennen realisiert werden. Es wird gezeigt, dass ein Strahlschlaufenreaktor in Kombination mit einer Crossflow-Mikrofiltration ein geeignetes System dargestellt, um die Anforderungen an eine zukuenftige Abwasserreinigung zu gewaehrleisten. In einem solchen System kann ein CSB-Umsatz von 95% bei Verweilzeiten von 0,5 Stunden realisiert werden. Durch Crossflow-Mikrofiltration wird eine Biomassekonzentration bis 30 g TS/l im Bioreaktor eingestellt. (orig.)

  2. New catalysts for photocatalytic cleaning of waste water; Neue Katalysatoren zur photokatalytischen Abwasserreinigung

    Energy Technology Data Exchange (ETDEWEB)

    Lindner, M [Inst. for Solarenergieforschung GmbH, Hannover (Germany); Bahnemann, D [Inst. for Solarenergieforschung GmbH, Hannover (Germany); Hirthe, B [Sachtleben Chemie, Duisburg (Germany); Griebler, W D [Sachtleben Chemie, Duisburg (Germany)

    1994-11-01

    Cleaning of polluted ground and waste water meets with particular problems where the group of halogenated hydrocarbons is concerned, which are not, or not readily, to be biologically degraded by conventional techniques. As an alternative technique to waste water cleaning, a method known as photocatalysis was proposed some years ago, which removes the organic pollutants by oxidation at semiconductor particles exposed to a light source. The article reports on a newly developed photocatalyst with distinctly enhanced pollutant degradation efficiency. (orig./EF) [Deutsch] Besondere Schwierigkeiten bei der Reinigung verschmutzter Grund- und Abwaesser bereitet die Gruppe der halogenierten Kohlenwasserstoffe, die sich nicht oder nur schwer auf herkoemmliche Weise biologisch abbauen lassen. Als alternative Technik zur Abwasserreinigung wurde vor einigen Jahren die sogenannte Photokatalyse vorgeschlagen, bei der die organischen Schadstoffe durch Oxidation an belichteten Halbleiterteilchen entfernt werden. Nachfolgend wird ueber einen neu entwickelten Photokatalysator berichtet, mit dessen Hilfe eine deutliche Steigerung der Effektivitaet des photokatalytischen Schadstoffabbaus gelingt. (orig./EF)

  3. Wie schreiben sprachschwache Kinder? Beitrag zum Zusammenhang zwischen explizitem und implizitem Sprachwissen

    OpenAIRE

    Schaller, Pascale

    2017-01-01

    Der Beitrag fokussiert den Zusammenhang zwischen sprachlich explizitem und implizitem Wissen in den Bereichen Wortschatz, Grammatik und Orthographie bei sprachschwachen Kindern. Er plädiert dafür, Schreiben als Sprachhandlung aufzufassen und neben dem Textprodukt den Schreibprozess und die Sprachwissensvoraussetzungen der Kinder als diagnostisch relevante Aspekte zu reflektieren. Anhand empirischer Analysen aus einer explorativen Studie wird aufgezeigt, dass sich das Verhältnis von explizitem...

  4. Advanced waste water cleaning with the aid of an algae biofilm; Weitergehende Abwasserreinigung mit Hilfe eines Algenbiofilms

    Energy Technology Data Exchange (ETDEWEB)

    Schumacher, G.; Patzold, V.; Ike, A.; Sekoulov, I. [Technische Univ. Hamburg-Harburg, Hamburg (Germany). Arbeitsbereich Abwasserwirtschaft

    1999-07-01

    These first investigations have led to results indicating that advanced waste water cleaning with the aid of algae biofilm as a downstream process stage is feasible. The concentration of phosphorus in waste water could be reduced to less than 1 mg per litre. Ammonium, which is toxic to fish, was nitrified, and the overall nitrogen concentration could be cut down. The concentration of bacteria was reduced by means of a close-to-nature process to less than the limiting values set by the European Union directive governing the quality of bathing waters. (orig.) [German] Die Ergebnisse dieser ersten Untersuchungen zeigen, dass eine weitergehende Abwasserreinigung mit Hilfe eines Algenbiofilms als nachgeschaltete Verfahrensstufe moeglich ist. Die Phosphorkonzentration im Abwasser konnte auf unter 1 mg/l reduziert werden. Fischgiftiges Ammonium wurde nitrifiziert und die Gesamtstickstoffkonzentration konnte gesenkt werden. Die Bakterienkonzentration konnte mit Hilfe eines naturnahen Verfahrens bis unter die Grenzwerte der EU-Richtlinie ueber die Qualitaet der Badegewaesser reduziert werden. (orig.)

  5. Advanced waste water treatment in small sewage plants with less than 50 PE; Weitergehende Abwasserreinigung in biologischen Kleinklaeranlagen mit einem Anschluss < 50 EW

    Energy Technology Data Exchange (ETDEWEB)

    Peukert, V.

    1999-12-31

    deutlich geringerer Schlammanfall nachgewiesen. Die Betriebs- und Investitionskosten sowie der technologische Aufwand sind nicht hoeher als in vergleichbaren Belebtschlammanlagen ohne weitergehende Abwasserreinigung. (orig.)

  6. Contribution of occupational therapy for patients with depression / Beitrag der Ergotherapie in der Wahrnehmung von Menschen mit Depression

    Directory of Open Access Journals (Sweden)

    Treusch Yvonne

    2016-12-01

    Full Text Available In Bezug auf den professionellen Beitrag und die Wirkfaktoren der Ergotherapie bei Menschen mit Depression existieren bislang wenige Studien. Dies steht im Kontrast zum praktischen und quantitativen Beitrag dieser Therapieform.

  7. Using continuous UV extinction measurements to monitor and control the aerated phase of sequencing batch reactors; Einsatz der kontinuierlichen UV-Extinktionsmessung fuer die Ueberwachung und Regelung der Belueftungsphase in SBR-Anlagen

    Energy Technology Data Exchange (ETDEWEB)

    Nicolet, L.; Rott, U. [Stuttgart Univ. (Germany). Inst. fuer Siedlungswasserbau, Wasserguete- und Abfallwirtschaft; Bardeck, S. [Optek-Danulat GmbH (Germany)

    1999-07-01

    The work describes the measurement of UV extinction - expressed as the spectral absorption coefficient SAC - at a randomly chosen wave length as a technique for monitoring organic load in effluents from sequencing batch reactors (SBR) at municipal and industrial waste water treatment plants. Further described is to what extent the continuous determination of the SAC can be used in practice for the control of the aerated phase of sequencing batch reactors. By this means, process stabilization and optimization can be achieved and operating reliability can be enhanced. (orig.) [German] Inhalt dieses Beitrages ist es, die Messung der UV-Extinktion - ausgedrueckt durch den spektralen Absorptionskoeffizient (SAK) - bei einer frei gewaehlten Wellenlaenge als Verfahren fuer die Ueberwachung der organischen Belastung in den Ablaeufen von SBR-Anlagen (Sequencing-Batch-Reactor) in der kommunalen und industriellen Abwasserreinigung vorzustellen. Weiterhin soll dargestellt werden, in wieweit die kontinuierliche Bestimmung des SAK in der Praxis fuer die Regelung der beluefteten Phase von SBR-Anlagen eingesetzt werden kann. Hiermit kann eine Prozessstabilisierung und -optimierung der Anlagen erreicht sowie die Betriebssicherheit erhoeht werden. (orig.)

  8. Ein Beitrag zur Blutzellmorphologie ausgewählter karnivorer Zootierarten

    OpenAIRE

    Güth, Henrike

    2004-01-01

    Henrike Güth Ein Beitrag zur Blutzellmorphologie ausgewählter karnivorer Zootierarten Zoo Leipzig Januar 2003 156 Seiten, 222 Abbildungen, 67 Tabellen, 1 Graphik, 151 Literaturangaben, Anhang mit 25 Abbildungen und 6 Tabellen Zur Beurteilung des Blutbildes ist es nötig, neben der quantitativen Betrachtung der Blutzellen auch ihre Morphologie in die Untersuchungen einzubeziehen. In der Praxis werden dazu häufig nach May-Grünwald-Giemsa-gefärbte Ausstriche verwendet. Referenzwerte zur physiolog...

  9. Entgrenzung durch Medien: Internationalisierungsprozesse als Rahmenbedingung der Mediendidaktik

    Directory of Open Access Journals (Sweden)

    Michael Klebl

    2006-07-01

    Full Text Available Die Mediendidaktik ist eine Teildisziplin der Medienpädagogik und hat in den vergangenen Jahren einen enormen Zuwachs an Nachfrage und Bedeutung erfahren. Dieser Bedeutungszuwachs ist bedingt durch den verstärkten Einsatz digitaler Informations- und Kommunikationstechniken in Bildungsprozessen (Stichwort «E- Learning». Der vorliegende Beitrag entwickelt die These, dass die Mediendidaktik ausgehend von medientechnischen Entwicklungen im Kontext von Globalisierung einer Entgrenzung unterworfen ist. Diese Entgrenzung ist Chance und Risiko zugleich. Der vorliegende Beitrag klärt zunächst den Begriff der Entgrenzung. Anhand dreier Phänomene werden Prozesse der Entgrenzung für die Mediendidaktik beschrieben. Ausgehend von der Problematisierung der Prozesse von Entgrenzung werden abschliessend einige Folgerungen für die Mediendidaktik als Teildisziplin der Medienpädagogik zur Diskussion gestellt.

  10. What contribution can the gas infrastructure make to the energy transition?; Welchen Beitrag kann die Gasinfrastruktur fuer die Energiewende leisten?

    Energy Technology Data Exchange (ETDEWEB)

    Bothe, David; Janssen, Matthias; Poel, Sander van der [Frontier Economics, Koeln (Germany); and others

    2017-11-15

    In the long term, the sector coupling will convert other areas of consumption such as heat and transport to purely renewable energy sources. A model-based analysis of system costs across all stages of the value chain shows that the existing gas infrastructure in particular can make an important contribution to achieving a comprehensive energy turnaround at low cost. Preserving the gas networks in connection with the use of green gas as a further end energy carrier in addition to electricity leads to significantly lower overall costs than a comprehensive electrification of all end applications. This can also help overcome acceptance problems. [German] Mit der Sektorkopplung werden langfristig weitere Verbrauchsbereiche wie Waerme und Verkehr auf rein erneuerbare Energiequellen umgestellt. Eine modellgestuetzte Analyse der Systemkosten ueber alle Wertschoepfungsstufen hinweg zeigt, dass insbesondere die vorhandene Gasinfrastruktur einen wichtigen Beitrag leisten kann, eine umfassende Energiewende kostenguenstig zu erreichen. Ein Erhalt der Gasnetze in Verbindung mit der Nutzung von Gruenem Gas als weiterem Endenergietraeger neben Strom fuehrt zu deutlich niedrigeren Gesamtkosten als eine umfassende Elektrifizierung aller Endanwendungen. Zudem kann dies helfen, Akzeptanzprobleme zu ueberwinden.

  11. Immer nur die zweitbeste Lösung? Protokolle als Dokumentationsmethode für qualitative Interviews

    Directory of Open Access Journals (Sweden)

    Dita Vogel

    2017-12-01

    Full Text Available In der methodischen Literatur zu qualitativen Interviews wird als Standardverfahren oft die Aufzeichnung mit einem Aufnahmegerät und anschließende wortgetreue Verschriftlichung (Transkription empfohlen. Protokolle werden als Mittel der Interviewdokumentation zumeist als zweitbeste Lösung für den Fall dargestellt, dass Mitschnitte nicht möglich sind. Diese Position stellen wir in diesem Beitrag aufgrund theoretischer Überlegungen und empirischer Erfahrungen infrage. Vor- und Nachteile der Dokumentationsformen "Audiomitschnitt + Transkription" und "Notizen + Protokollierung" werden systematisch gegenübergestellt. Anschließend wird anhand von zwei Studien exemplarisch verdeutlicht, dass die Protokollierung die beste Lösung zur Dokumentation der Interviewdaten sein kann. In beiden Studien wurden in Interviews sensible Themen behandelt und die Erhebung grundlegender Informationen über Prozesse und Routinen bezweckt. Grundsätzlich kann Protokollierung angezeigt sein, wenn weniger die Interpretation des Gesagten als vielmehr dessen Intention im Fokus der Forschung ist. Außerdem sollte eine Protokollierung erwogen werden, wenn eine Aufnahme besonders interessante InterviewpartnerInnen von der Teilnahme abhalten oder ein offenes Gespräch verhindern könnte. Mit diesem Beitrag wollen wir zu einer Auseinandersetzung darüber anregen, wann Protokollieren angemessen ist und wie es methodisch angelegt sein sollte.

  12. Das „neue“ Private. Familie als intime Gefühlsgemeinschaft

    Directory of Open Access Journals (Sweden)

    Regina Harzer

    2006-11-01

    Full Text Available Methodisch versteht sich die Habilitationsschrift als Beitrag zur Rekonstruktion moderner politischer Philosophie. Als zentraler Ansatzpunkt dient das Familienkonzept von Rousseau, seine Schriften werden auf Geschlechterkonstruktionen und bürgerliche Geschlechterordnungen hin untersucht. Grundanliegen der Studie ist es, Bürgerlichkeit unter ihrem zentralen Aspekt des Privaten zu betrachten und in den Kontext moderner kontraktualistischer Philosophie zu stellen. Die Autorin vertritt die Ausgangsthese, Rousseau müsse eine „Schlüsselstellung“ (S. 9 in der Geschichte der bürgerlichen Geschlechter- und Familienordnung zugesprochen werden. Durch ihn sei die Trennung des Privaten vom Öffentlichen eingeleitet und festgeschrieben worden.

  13. Using the tool of Life Cycle Assessment for evaluating processes of waste water and sludge treatment; Einsatzmoeglichkeiten des Life Cycle Assessment in der Bewertung von Verfahren der Abwasser- und Schlammbehandlung

    Energy Technology Data Exchange (ETDEWEB)

    Gigerl, T.; Rosenwinkel, K.H. [Hannover Univ. (Germany). Inst. fuer Siedlungswasserwirtschaft und Abfalltechnik; Wiebusch, B. [Eurawasser Aufbereitungs- und Entsorgungs GmbH, Berlin (Germany)

    1999-07-01

    Whenever advances in waste water treatment were achieved in the past they have spelt technically more sophisticated processes for the elimination of water-toxic products. At present, waste water treatment technology faces further demands. Apart from the issue of economy and the avoidance of excessive burdens to citizens, a question increasingly raised is whether waste water cleaning processes are themselves environment-friendly. Related studies are internationally known as Life Cycle Assessment (LCA). (orig.) [German] Fortschritte in der Abwasserreinigung bedeuteten bisher jeweils technisch aufwendigerere Loesungen zur Eliminierung gewaesserschaedigender Stoffe. Heute muss sich die Abwassertechnik weiteren Anforderungen stellen. Neben der Wirtschaftlichkeit und damit der Vermeidung unzumutbarer Belastungen fuer die Buerger wird immer mehr die Frage gestellt, ob die Verfahren der Abwasserreinigung selbst umweltvertraeglich sind. Die damit verbundenen Untersuchungen werden international als 'Life Cycle Assessment (LCA)' bezeichnet. (orig.)

  14. Medienbildung als Grundbegriff der Medienpädagogik. Begriffliche Grundlagen für eine Theorie der Medienpädagogik

    Directory of Open Access Journals (Sweden)

    Dieter Spanhel

    2011-09-01

    Full Text Available Der Beitrag zielt darauf, Medienbildung als zentralen Grundbegriff einer Theorie der Medienpädagogik einzuführen, weil er besser als der Begriff Medienkompetenz geeignet ist, den Gegenstandsbereich und die Aufgaben der Medienpädagogik in ihrer Komplexität zu erfassen. Dazu wird der Begriff Medienbildung in einen anthropologischen, einen systemtheoretischen und einen bildungstheoretischen Bezugrahmen gestellt. Auf dieser Basis lässt sich dann Medienbildung als ein selbst gesteuerter Prozess beschreiben und daraus können die Konsequenzen für die medienpädagogische Praxis abgeleitet werden.

  15. Wider die dualistische Position akademischen Schreibens: Das Schreiben einer Doktorarbeit als leibgebundene Praxis

    OpenAIRE

    Hanrahan, Mary

    2003-01-01

    Dieser Beitrag befasst sich mit der Spannung zwischen der dualistischen Tradition unseres Kulturkreises (WERTHEIM, 1999) einerseits und neueren Ansätzen, die die Konstruktion und Genese von Wissen als leibgebundenes Handeln innerhalb biologischer und ökologischer Systeme nachzuvollziehen versuchen andererseits (z.B. DAMASIO, 1994; LEAR, 1998; LEMKE, 1995; MATURANA & VARELA, 1992). Dabei werden auch Implikationen eines biosozialen Modells für Forschungsmethodologie und für akademisches Schreib...

  16. Interview als Text vs. Interview als Interaktion

    Directory of Open Access Journals (Sweden)

    Arnulf Deppermann

    2013-09-01

    Full Text Available Das Interview ist nach wie vor das beliebteste sozialwissenschaftliche Verfahren des Datengewinns. Ökonomie der Erhebung, Vergleichbarkeit und die Möglichkeit, Einsicht in Praxisbereiche und historisch-biografische Dimensionen zu erhalten, die der direkten Beobachtung kaum zugänglich sind, machen seine Attraktivität aus. Zugleich mehren sich Kritiken, die seine Leistungsfähigkeit problematisieren, indem sie auf die begrenzte Reichweite der Explikationsfähigkeiten der Befragten, die Reaktivität der Erhebung oder die Differenz zwischen Handeln und dem Bericht über Handeln verweisen. Im Beitrag wird zwischen Ansätzen, die das Interview als Text, und solchen, die es als Interaktion verstehen, unterschieden. Nach dem Text-Verständnis werden Interviews unter inhaltlichen Gesichtspunkten analysiert und als Zugang zu einer vorgängigen sozialen oder psychischen Wirklichkeit angesehen. Das Interaktions-Verständnis versteht Interviews dagegen als situierte Praxis, in welcher im Hier und Jetzt von InterviewerInnen und Befragten gemeinsam soziale Sinnstrukturen hergestellt werden. Anhand ubiquitärer Phänomene der Interviewinteraktion – Fragen, Antworten und die Selbstpositionierung von InterviewerInnen und Befragten – werden Praktiken des interaktiv-performativen Handelns im Interview dargestellt. Ihre Relevanz für die Interviewkonstitution und ihre Erkenntnispotenziale für die Interviewauswertung werden aufgezeigt. Es wird dafür plädiert, die interaktive Konstitutionsweise von Interviews empirisch zu erforschen und methodisch konsequent zu berücksichtigen. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1303131

  17. Staat und Welt als Bezugssysteme des Handelns im Prozess der Globalisierung

    Directory of Open Access Journals (Sweden)

    Lutz Zündorf

    2002-07-01

    Full Text Available In diesem Beitrag wird Globalisierung als Prozess der Umstellung von Bezugssystemen des Denkens und Handelns von "Staat" auf "Welt" konzipiert. Von der klassischen Definition des Nationalstaates ausgehend, werden zuerst drei staatszentrierte Bezugssysteme (Rechtsstaat, Sozialstaat, Territorialstaat skizziert. Im zweiten Schritt werden globale Bezugssysteme (Welt als einheitlicher Markt, als Gefüge von Herrschaftsgebilden, als Konglomerat von Kulturen umrissen. Die Argumentation läuft darauf hinaus, zu zeigen, dass es sich bei diesen Konzeptionen keineswegs um geschlossene und harmonische Gesellschafts- und Weltbilder handelt; vielmehr enthält jedes der sechs Bezugsysteme spezifische Spannungs- und Konfliktlinien, aus denen sich ihre jeweilige Dynamik speist. Im dritten Schritt werden Prozesse der Umstellung der Bezugssysteme in Richtung Globalität auf drei Ebenen analysiert: auf der Ebene umfassender historischer Prozesse, auf der Ebene staatlichen Handelns und auf der Ebene individueller Akteure.

  18. Der Wandel der Erwerbsformen und der Beitrag der Hartz-Reformen: Berlin und die Bundesrepublik Deutschland im Vergleich

    OpenAIRE

    Oschmiansky, Heidi

    2007-01-01

    "Seit den 1980er Jahren wird der Wandel der Erwerbsformen in der Bundesrepublik Deutschland immer stärker sichtbar. Während die sozial abgesicherte, abhängige und unbefristete Vollzeiterwerbsform - das sog. 'Normalarbeitsverhältnis' - seither leicht an Bedeutung verloren hat, zeigen sich bei den übrigen Erwerbsformen zum Teil hohe Zuwächse und eine zunehmende Differenzierung. Der vorliegende Beitrag untersucht den Wandel der Erwerbsformen zwischen 1985 und 2005 auf Basis von Mikrozensus-Daten...

  19. Combination of biological treatment of waste air and liquid effluents in small and medium-sized businesses by using spherical carrier media in exchange with each other. Final report; Kombination der biologischen Behandlung von Abluft- und Abwasserreinigung in kleinen und mittleren Unternehmen durch die Verwendung von kugeligen Traegermaterialien im gegenseitigen Austausch. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Kunz, P.M.; Brunk, M.; Bentz, P.; Bach, K.; Marcos del Rio, O.; Stahl, B.; Wolf, C.

    2002-05-08

    A combined system for biological treatment of solvent-contaminated liquid and gaseous effluents was to be constructed. The system was to be mobile for demonstration purposes in industrial processes and was to serve for dimensioning of full-scale systems. The system works by a combined process via exchange of spherical carriers with a growth of micro-organisms. Two pilot systems of the Institut fuer Biologische Verfahrenstechnik, one for liquid and one for gaseous effluents, were combined for this purpose, ensuring exchange of carrier materials between the two units. (orig.) [German] Aufgabe im Rahmen dieses F+E-Vorhabens war es gewesen, eine kombinierte biologische Abluft- und Abwasserreinigungsanlage - speziell fuer loesungsmittelhaltige Abluft und Abwaesser - zu untersuchen. Dazu sollte eine Anlage aufgebaut werden, die auch als Demonstrations- und Versuchsanlage zu Industriebetrieben gebracht und dort zur Dimensionierung von full-scale-Anlage eingesetzt werden kann. Idee fuer dieses Vorhaben war gewesen, die Kombination beider Behandlungssysteme ueber den Austausch von mit Mikroorganismen bewachsenem Traegermaterial herzustellen. Am Institut fuer Biologische Verfahrenstechnik existierte bereits eine Pilotanlage fuer die biologische Abwasserreinigung mit kugeligem Traegermaterial (Vario-Bio-Reaktor) und eine Pilotanlage fuer die biologische Behandlung von Abluft nach dem Trickling-Filter-Prinzip mit ebenfalls kugeligem Traegermaterial. Diese beiden Anlagen sollten miteinander kombiniert und der Austausch des Traegermaterials hergestellt werden. (orig.)

  20. Grundbildung Medien als Teil erwachsenenpädagogischer Professionalitätsentwicklung. Überlegungen zur medienpädagogischen Professionalisierung angehender Erwachsenenbildnerinnen und Erwachsenenbildner

    Directory of Open Access Journals (Sweden)

    Franziska Bellinger

    2018-03-01

    Full Text Available Der Beitrag nimmt den Umstand zum Ausgangspunkt, dass die Erwachsenenbildung sich sowohl mit der Herausforderung konfrontiert sieht Erwachsenenbildnerinnen und Erwachsenenbildner bei der Aneignung von medienpädagogisch kompetentem Handeln zu unterstützen, als auch zur Vermittlung medienbezogener Kompetenzen zu befähigen (Schmidt-Hertha et al. 2017, 36. Die Ubiquität von (digitalen Medien in menschlichen Lebenswelten bedarf dabei keiner besonderen Betonung mehr. Medien sind Teil der Lebenswelt von Erwachsenen und in der Folge zu einem Verantwortungsbereich der Erwachsenenbildung avanciert. Die Befähigung erwachsener Menschen zur Teilhabe an der digitalen Welt kann als Kernaufgabe unter den Bedingungen von Digitalisierung gesehen werden, was voraussetzt, dass professionell tätige Erwachsenenbildnerinnen und Erwachsenenbildner Veränderungsprozesse, die mit dem Phänomen einhergehen, in den Tätigkeits- und Handlungsfeldern aktiv mitgestalten. Im vorliegenden Beitrag wird der professionstheoretische Diskurs in der Erwachsenenbildung als Hintergrundfolie aufgegriffen, um Herausforderungen und Chancen für die medienpädagogische Professionalitätsentwicklung für die Erwachsenenbildung zu skizzieren. Professionalitätsentwicklung wird dabei als lebenslanger Prozess verstanden, der in einem akademischen Studium mit entsprechendem Schwerpunkt angestossen und in der späteren Berufspraxis weiter geformt wird. Es wird ferner ein Vorschlag unterbreitet, der inhaltliche und thematische Dimensionen einer medienpädagogischen Grundbildung für die Erwachsenenbildung skizziert. Deren Integration in Studiengängen der erziehungswissenschaftlichen Teildisziplin erscheint lohnenswert im Hinblick auf die Professionalisierung angehender Erwachsenenbildnerinnen und Erwachsenenbildner.

  1. Intermedialität als Grundsatzdiskussion. Zum Sammelband Sprechen über Bilder. Sprechen in Bildern: Studien zum Wechselverhältnis von Bild und Sprache

    Directory of Open Access Journals (Sweden)

    Angela Oster

    2016-01-01

    Full Text Available Der Sammelband Sprechen über Bilder. Sprechen in Bildern bietet mehr als nur einen weiteren Beitrag zur Intermedialität. Er erforscht anlässlich des interartialen Austauschs zwischen Bild unf Text die Modi der Wissenschaft und versucht, diesbezüglich neue Impulse zu geben. Methodisch wird dabei die Rezeptionsästhetik favorisiert.

  2. Smarte Städte. Digitalisierte urbane Infrastrukturen und ihre Subjekte als Themenfeld kritischer Stadtforschung

    Directory of Open Access Journals (Sweden)

    Sybille Bauriedl

    2017-06-01

    Full Text Available Welche Bedeutung hat eine zunehmend digitale Vernetzung für (europäische Städte und ihre Bewohner_innen? Die aktuelle kritische „Smart City“-Forschung versucht diese Frage für unterschiedliche Aspekte der Stadtpolitik zu beantworten. Sie betrachtet Smart City als Marketingetikett wettbewerbsorientierter Stadtregierungen, als Dienstleistungsprodukt von IT-Konzernen und als Eingangstor zur deregulierten Vernetzung digitaler Daten. Dieser Beitrag setzt sich systematisch mit der Verwobenheit dieser Aspekte auseinander, mit einem Fokus auf erstens digital vernetzte Infrastrukturen kommunaler Daseinsvorsorge und zweitens auf vernetzte Interaktions- und Kommunikationstechnologien in der Alltagspraxis. Dabei wird die diskursive, die strukturelle und die subjektive Ebene von Optimierungsversprechen, Selbststeuerung und Ermächtigung diskutiert. Diese Betrachtung zeigt Städte als Orte spontaner, ungeplanter und widerständiger Interaktionen, die gleichzeitig an Effizienz-, Kontroll-, Optimierungs- und Wettbewerbsidealen ausgerichtet sind.

  3. Alternativen als Programm

    Directory of Open Access Journals (Sweden)

    Paulina Dobroć

    2018-03-01

    Full Text Available Der vorliegende Artikel soll einen Beitrag zu theoretischen Überlegungen einer Technikfolgenabschätzung (TA der Alternativen leisten. Ausgehend von der Annahme, dass TA seit ihrer Entstehung den Anspruch auf die Entwicklung von (technischen Alternativen erhoben hat, wird hier der Versuch unternommen, die Rolle der TA im Rahmen aktueller Innovationsprozesse zu reflektieren und (neu zu definieren. Dies scheint vor allem im Hinblick auf aktuelle gesellschaftliche Herausforderungen notwendig. Zu diesem Zweck wird eine Grundannahme Lothar Hacks über das Verhältnis von Gesellschaft und Technik herangezogen. Seine Annahme besagt, dass die kontinuierliche Überführung von sozialen Problemen und Leitbildern in enge technische Lösungsansätze in hochindustrialisierten Ländern dominant und Teil der aktuellen gesellschaftlichen Probleme ist. Diese These wird im vorliegenden Artikel im Hinblick auf einen Perspektivenwechsel als Ausgangspunkt eines zukünftigen Forschungsprogramms der TA fruchtbar gemacht. Hierbei bildet das Denken in Alternativen von gesellschaftlichen Zukünften den zentralen Fokus.

  4. Critical Mass als performative Kritik der städtischen Verkehrspolitik? Fahrradfahren mit Judith Butler auf dem Gepäckträger

    Directory of Open Access Journals (Sweden)

    Anke Strüver

    2015-11-01

    Full Text Available Obwohl die meisten deutschen Großstädte über eine sehr schlechte Radverkehrsinfrastruktur verfügen, gewinnent innerstädtisches Radfahren und ein Engagement für das Rad als gleichberechtigtes Verkehrsmittel stark an Bedeutung. Als Indiz für dieses Engagement gelten in Hamburg die monatlichen Critical Mass Radfahrten unter dem Motto „We aren’t blocking traffic… we are traffic!“. Der Beitrag fragt vor diesem Hintergrund, inwiefern die Critical Mass als Aktionsform in Hamburg den Diskurs der autogerechten Stadt, die Straßenverkehrspolitik und die dominante räumliche Ordnung in Frage stellen kann und ob die Critical Mass als performative Kritik der normativen Ordnung im Sinne Judith Butlers verstanden werden kann.

  5. Qualität beim E-Learning: Der Lernende als Grundkategorie bei der Qualitätssicherung

    Directory of Open Access Journals (Sweden)

    Ulf Ehlers

    2002-03-01

    Full Text Available Qualität wird über die zukünftigen Erfolgschancen des E-Learning entscheiden. Das ist das Ergebnis vieler Analysen und Entwicklungen der letzten Zeit. So stellte etwa die KPMG-Studie heraus, dass es beim E-Learning nicht nur auf gute Technologie ankommt, sondern die betriebliche Lernkultur und der Lerner wesentlich mehr als bisher einzubeziehen sind. Dieser Beitrag beschäftigt sich damit, was Qualität beim E-Learning eigentlich ist und welche Konzepte zur Beschreibung und Sicherung von Qualität bestehen.

  6. Monitoring of organic loads at waste water treatment plant with due consideration of factual necessity, technical feasibility and statutory requirements; Erfassung der organischen Belastung bei Abwasserreinigungsanlagen unter Beachtung der fachlichen Notwendigkeit, der technischen Moeglichkeiten und der gesetzlichen Auflagen

    Energy Technology Data Exchange (ETDEWEB)

    Baumann, P. [Stuttgart Univ. (Germany). Inst. fuer Siedlungswasserbau, Wasserguete- und Abfallwirtschaft

    1999-07-01

    Between the statutory requirement and factual necessity for monitoring organic loads in waste water discharged to municipal and industrial waste water treatment plant and effluents from these there are substantial discrepancies. The paper points out the different approaches and gives recommendations on how to proceed in the future. At plant with stable nitrification, self and external monitoring for BOD{sub 5} can be distinctly reduced without fear of impaired process transparency or water quality. Monitoring organic loads online is little expedient technically, especially where effluent from municipal sewage treatment plants is concerned. But in the industrial sector there exist the most diverse applications with a view to carbon elimination. (orig.) [German] Zwischen den gesetzlichen Anforderungen und der fachlichen Notwendigkeit bei der Erfassung der organischen Belastung im Zu- und Ablauf von kommunalen und industriellen Klaeranlagen bestehen erhebliche Diskrepanzen. In diesem Beitrag werden die unterschiedlichen Ansaetze aufgezeigt und Empfehlungen fuer die zukuenftige Vorgehensweise gegeben. Bei Anlagen mit stabiler Nitrifikation ist die Selbst- wie Fremdueberwachung bezueglich BSB{sub 5} deutlich zu reduzieren, ohne dass Einbussen fuer Prozesstransparenz und Gewaesserqualitaet zu erwarten sind. Die online-Ueberwachung der organischen Belastung ist insbesondere bei Ablaeufen in kommunalen Klaeranlagen fachlich wenig sinnvoll, im Bereich der industriellen Abwasserreinigung ergeben sich dafuer bei dem Reinigungsziel der Kohlenstoffelimination dagegen verschiedenste Anwendungsmoeglichkeiten. (orig.)

  7. Developing an optimized treatment strategy for anaerobic waste water cleaning; Entwicklung einer optimierten Behandlungstrategie fuer die anaerobe Abwasserreinigung

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, W.; Manz, W.; Szewzyk, U.; Kozariszczuk, M.; Kraume, M. [Technische Univ. Berlin (Germany)

    1999-07-01

    The paper looks into the opportunities for and limitations of using oligonucleotide probes for in-situ hybridisation in anaerobic systems. As is demonstrated, a large part of the populations can be detected using this method and different physiological groups like sulfate reducers and methanogens can be verified with a high resolution. The technique permits assessing the physiological activity of these groups so that inferences to reactor performance can be drawn. Various physiological groups such as fermenters and homoacetogenous bacteria so far can be detected with inadequate resolution only. Ongoing work with a view to amending this is described. (orig.) [German] Dieser Beitrag beschaeftigt sich mit den Moeglichkeiten und Limitierungen des Einsatzes von Oligonukleotidsonden zur in situ Hybridisierung in anaeroben Systemen. Es wird gezeigt, dass ein grosser Teil der Population mit Hilfe dieser Methode erfasst werden kann und verschiedene physiologische Gruppen wie die Sulfatreduzierer und die Methanogenen mit hoher Aufloesung nachgewiesen werden koennen. Die physiologische Aktivitaet dieser Gruppen kann abgeschaetzt werden und damit sind Rueckschluesse auf die Reaktorleistung moeglich. Verschiedene physiologische Gruppen wie die Gaerer und die homoacetogenen Bakterien werden bisher nur in unzureichender Aufloesung erfasst. Die derzeit laufenden Arbeiten zur Loesung dieser Probleme werden beschrieben. (orig.)

  8. Das Portfolio als Beitrag zur Reflexion persönlicher Kompetenzentwicklung in der Religions-/PädagogInnenbildung. Chancen einer neuen Lern- und Bewertungskultur - am Beispiel einer Fallstudie

    Directory of Open Access Journals (Sweden)

    Alexander van Dellen

    2013-10-01

    Full Text Available ”Competence orientation” in pedagogy education constitutes a central point within the draft laws formulated on the 12th of June 2013. These see the use of portfolios as playing a crucial part of religious instruction education. This is based on the expectation that portfolios act as continuous and helpful companions throughout the various educational phases and therefore benefit students’ reflections on individual competence development. Portfolios allow effective measures towards personal development as a professional educator to be taken. The format at hand, which was conceived as a case study at the Institute for Practical Theology (department catechetics, religious education studies and religious didactics at the Faculty of Catholic Theology at the University of Innsbruck, is intended to be used as a basis for a discussion on the benefits of a continuous portfolio as a reflection tool for students’ personal competence development. The first step illustrates the genesis and structure of the portfolio concept (2, so that the second step can then outline the potentials held by this new culture of using portfolios as learning and assessment tools in religious instruction education (3. In den vom österreichischen Parlament am 12. Juni 2013 beschlossenen Gesetzesentwürfen zur zukünftigen PädagogInnenbildung stellt die Kompetenzorientierung einen Kernpunkt dar. In diesem Zusammenhang wird in der Ausbildung von Religions-/PädagogInnen der Einsatz von Portfolios verstärkt eine zentrale Rolle spielen. Damit ist die Hoffnung verbunden, dass das Portfolio als Kontinuum in den unterschiedlichen Phasen der Religions-/PädagogInnenbildung für Studierende ein hilfreiches Instrument für die Reflexion ihrer individuellen Kompetenzentwicklung bildet. Somit kann eine wirksame Maßnahme der persönlichen Entwicklung in der Professionalisierung für den Lehrberuf gesetzt werden. In den vorliegenden Ausführungen soll auf der Grundlage einer

  9. The contribution of tyre and brake abrasion to soot levels in streets; Beitrag des Reifen- und Bremsenabriebs zur Russemission an Strassen

    Energy Technology Data Exchange (ETDEWEB)

    Rauterberg-Wulff, A.

    1998-09-01

    After the coming into force of the new soot emission thresholds as of July 1998, excess values are measured along many city streets. The author investigated whether tyre and brake abrasion contributes to soot emissions in addition to diesel soot. For this purpose, characteristic material and physical parameters of particles of diesel soot, tyre and brake material were investigated by thermography, AAS, and SEM. With the aid of a receptor-oriented approach, the contribution of these particles to soot levels measured in a highway tunnel and a Berlin city street could be assessed. The contribution of local traffic was calculated from the difference between soot levels along the road and in a background station. The measurements inside the tunnel served to determine emissin factors for diesel soot and abrasion particles from tyres and brakes. (orig.) [Deutsch] Mit Inkrafttreten des endgueltigen Russ-Immissionswertes der 23. Verordnung zum Bundes-Immissionsschutzgesetz im Juli 1998 ist an zahlreichen innerstaedtischen Strassen mit einer Ueberschreitung dieser Werte zu rechnen. Zur Beantwortung der Frage, inwieweit neben Dieselruss auch Reifen- und Bremsenabrieb zur verkehrsbedingten Russimmission beitragen, wurden charakteristische stoffliche und physikalische Eigenschaften von Dieselruss, Reifenabrieb und Bremsenabrieb mit der Thermographie, der AAS und der Rasterelektronenmikroskopie untersucht. Mit Hilfe dieses rezeptororientierten Ansatzes konnte der Beitrag dieser Partikel zur Russimmission in einem Autobahntunnel und an einer Hauptverkehrsstrasse in Berlin bestimmt werden, wobei zuerst der Beitrag des lokalen Verkehrs zur Russimmission aus der Differenz zwischen der Russimmission an der Strassen- und einer Hintergrundstation berechnet wurde. Mit Hilfe der Messungen im Tunnel konnten Emissionsfaktoren fuer Dieselruss und fuer Reifen- und Bremsenabriebpartikel bestimmt werden. (orig.)

  10. Game of Thrones – Fernsehserien als Artikulation gesellschaftlich-unbewusster Phantasien

    Directory of Open Access Journals (Sweden)

    Gerald Poscheschnik

    2016-08-01

    Full Text Available Kulturelle Produkte, wie z.B. Fernsehserien, lassen sich als Artikulationsformen gesellschaftspolitischer Phantasien verstehen, die bewusste und unbewusste Elemente in sich bergen. Game of Thrones, ein furioses Fantasy-Mittelalterspektakel, aufgeladen mit Gewalt und Sex, scheint auf den ersten Blick nur wenig tagesaktuelle Bezüge aufzuweisen. Eine psychoanalytische Untersuchung, die die Serie ihres manifesten Gewands entkleidet, legt wesentliche Elemente und ihre Relationen frei, die frappante Parallelen zu rezenten gesellschaftspolitischen Phantasien offenlegen. Die Verhältnisse am fiktiven Kontinent Westeros bieten sich als Zeitdiagnose einer niedergehenden Kultur an, deren Potentaten völlig von einem Ränkespiel um Macht und Einfluss absorbiert sind und ihre Wahrnehmung all dem verweigern, was nicht ihrem eigenen Machterhalt dient. Der durch eine Mauer abgeschottete Norden des Landes kann als Deponie für die verdrängten Nebenwirkungen des eigenen Treibens, wie z.B. Umweltzerstörung und menschliches Elend, verstanden werden, deren deletäre Wirkung letztlich die eigene Existenz bedroht. Der ferne Kontinent Essos repräsentiert die Hoffnung, es könnte noch eine Wende oder Alternative entstehen. Die Medienpädagogik kann einen bildungstheoretischen Beitrag zum Verständnis moderner Fernsehserien leisten, benötigt dazu aber auch den interdisziplinären Austausch.

  11. Cyber-Mobbing als verletzender Sprechakt im Sinne Judith Butlers

    Directory of Open Access Journals (Sweden)

    Katharina Luckner

    2012-12-01

    Full Text Available Dieser Beitrag widmet sich der Frage, inwiefern Cyber-Mobbing unter Bezugnahme auf Judith Butlers sprach- bzw. diskurstheoretisches Konzept als verletzender Sprechakt verstanden werden kann. Zu diesem Zweck werden in einem ersten Schritt die Besonderheiten von Cyber-Mobbing aufgezeigt und im Anschluss daran ein für diesen Text geeigneter Cyber-Mobbing-Begriff formuliert. Daraufhin erfolgt eine interpretative Auseinandersetzung mit der Butlerschen Konzeption verletzender Sprechakte, bevor anschließend anhand wesentlicher Schnittstellen herausgearbeitet wird, inwiefern Cyber-Mobbing als ein solcher verletzender sprachlicher Akt begriffen werden kann. Resümierend werden die zentralen Ergebnisse der Ausarbeitung zusammengefasst und es wird danach gefragt, welche Konsequenzen bzw. Folgen sich hieraus für ein mögliches verändertes Verständnis von Cyber-Mobbing ergeben.This Paper argues whether cyber bullying can be understood as violating speach act with reference to Judith Butler by starting with a definition of cyber bullying (respectively the term cyber 'mobbing' which is used synonymously in German speaking countries and an outline of Butler's theory. After that, the question of a new or different understanding of cyber bullying and its consequences is discussed.

  12. Rehabilitierungs-Szenarien, Geschichten über Hexen, Verdingkinder, Flüchtlingshelfer usw.

    OpenAIRE

    Rüegger, Vanessa

    2015-01-01

    In den vergangenen Jahren haben Parlamente, Regierungen und Gerichte unterschiedliche Personen und Personengruppen rehabilitiert. Der vorliegende Beitrag bietet einen Überblick über die jüngst in der Schweiz ausgesprochenen Rehabilitierungen, ordnet diese rechtsdogmatisch ein und zeigt weiter die Funktionen und Grenzen der Rehabilitierung als Form staatlicher ,Vergangenheitsbewältigung‘ auf. Der Beitrag schliesst mit der Erkenntnis, dass Flüchtlingshelfer, Spanienkämpfer, administrativ Versor...

  13. Zur Aktualität der Etikettierungsperspektive als Ideologiekritik. Ein Beitrag zur Debatte um kritische Polizeiforschung

    Directory of Open Access Journals (Sweden)

    Helga Cremer-Schäfer

    2014-10-01

    Full Text Available Zu kritischer Institutionenforschung gehört, über die Herrschaftsfunktionen von gesellschaftlichen Institutionen, ihrer Organisationen (Apparate/Instanzen und die von ihnen verwalteten und angewendeten Kategorisierungen aufzuklären. Mit der Anwendung des Etiketts ,Verbrechen‘ beteiligt sich die Polizei als eine Instanz an der Institution ,Verbrechen und Strafe‘, das heißt an legitimierter sozialer Ausschließung (Zuarbeit zu Bestrafung, Inszenierung von Bedrohungsszenarien, Verwaltung der Paria-Bevölkerung. Zu kritischer Polizeiforschung gehört daher auch ein Dauer-Monitoring polizeilich betriebener ,Kriminalisierung‘ von Konflikten, Lebensweisen, Ärgernissen und Lebenskatastrophen. Einen theoretischen Rahmen bieten Etikettierungstheorien und Ideologiekritik. Positiv gewendet: Im Verbund mit kritischer Alltags- und Kulturforschung kann kritische Polizeiforschung zudem für die intellektuelle Verstehbarkeit kriminalisierter Konflikte und Lebensweisen sorgen und damit für die Wiederaneignung von Konflikten.

  14. Qualitätssicherung an Hochschulen durch Zulassungsverfahren

    OpenAIRE

    Hell, Benedikt

    2007-01-01

    Dieser Beitrag zeigt auf, dass Zulassungsverfahren einen wichtigen Beitrag zur Qualitätssicherung im tertiären Bildungsbereich leisten können. In Form eines Gedankenspiels wird das Portersehe Value Chain Framework herangezogen, um die besondere Stellung von Auswahlverfahren als Qualitätssicherungselement aufzuzeigen. Einen weiteren Schwerpunkt bildet die Analyse der prognostischen Aussagekraft und der Betrachtung des Nutzens von Auswahlverfahren. Hierzu werden Kennzahlen präsentiert, die durc...

  15. Kino filmų titrai kaip kalbų mokymosi priemonė. Untertitel als Mittel zum Fremdsprachenerwerb

    Directory of Open Access Journals (Sweden)

    Alina Baravykaitė

    2007-01-01

    Full Text Available Das in den letzten Jahren spürbare Bestreben der litauischen Gesetzgeber, Untertitelung von Fernsehfilmen zwecks Fremdsprachenerwerb gesetzlich anzuordnen, löste eine Auseinandersetzung in der Öffentlichkeit aus, die sich in der Presse sowie im Internet widerspiegelt und als Anstoß zum vorliegenden Beitrag dient. Diese Arbeit stellt den Versuch dar, die Möglichkeiten und Grenzen der Untertitelung als eines Mittels zum Fremdsprachenerwerb zu untersuchen. Auf Grund der fehlenden wissenschaftlichen Forschungen in diesem Bereich sollen dabei empirische Betrachtungen und die vergleichende Textanalyse von Original und Übersetzung als Hilfe dienen. Auch wenn die Relevanz der Untertitelung für den Fremdsprachenerwerb nicht bestreitbar ist, ist sie aber zugleich nicht zu überschätzen: Durch die lediglich für diese Form der audiovisuellen Übersetzung charakteristischen Merkmale (kurze Einblendezeit, kondensierte Sprache und begrenzte Übertragungsmöglichkeiten von Realia-Begriffen, Phraseologismen, Intertextualismen, dem Wortspiel etc. bleiben dem Zuschauer oft sprachliche Stilmittel vorenthalten und der in allen Übersetzungsbereichen vorkommende unausweichliche Sinn- und Wirkungsverlust des Originals wird erheblich verstärkt. Anbetracht der erwähnten Aspekte und der häufigen fehlerhaften Übersetzungen sollen Untertitel nur als Hilfsmittel beim Fremdsprachenerwerb angewendet werden, wobei herkömmliche Lehr- und Lernstrategien von Fremdsprachen in den Vordergrund treten müssen.

  16. "Das unausgesprochene Gefühl der Unzugehörigkeit" : Amerika als Zufluchtsmöglichkeit vor dem Selbst in Max Frischs Romanen Stiller und Homo faber

    Directory of Open Access Journals (Sweden)

    Vesna Kondrič Horvat

    1993-12-01

    Full Text Available In seiner Rede Emigranten, die er 1958 anläßlich der Georg-BtichnerPreis- Verleihung hielt und woraus das Titelzitat des vorliegenden Beitrags stammt, äußerte Max Frisch die Meinung, jeder frei gewahlte Wohnsitz solle dem Schriftsteller das unausgesprochene Gefühl der Unzugehörigkeit gestatten. Mit dem Satz: "Ich bin nicht Stiller!" (St 9 beginnt Frisch seinen 1954 veröffentlichten Roman Stiller. Ein Mann - ein Bildhauer -, der viele Versuche unternommen hat, seiner 'eigentlichen ', seelisch-existentiellen Identität zu entgehen, flieht schlieBlich, als alle anderen Versuche (sich im Spanischen Bürgerkrieg als ein mutiger Mann, sich in der Ehe als ein idealer Mann, sich in der Kunst als erfolgreicher Bildhauer zu bewahren scheitern, nach Amerika und läßt seine lungenkranke Frau Julika im Sanatorium in Davos zurück. Nach mehr als sechsjahrigem Fernbleiben kehrt er unter anderem Namen in die Heimat zurück und wird an der Schweizer Grenze - wegen vermeintlicher Verwicklung in eine Spionage-Affäre - verhaftet. An diesem Punkt beginnt der Roman.

  17. Smart Meter Rollout: Intelligente Messsysteme als Schnittstelle zum Kunden im Smart Grid und Smart Market

    Science.gov (United States)

    Vortanz, Karsten; Zayer, Peter

    Das Gesetz zur Digitalisierung der Energiewende ist verabschiedet. Ab 2017 sind moderne Messeinrichtungen (mME) und intelligente Messsysteme (iMSys) zu verbauen und zu betreiben. Der "deutsche Weg" für die Einführung von Smart Metern sieht einen stufenweisen Rollout sowie ein Höchstmaß an Informations- und Datensicherheit vor. Dabei spielen iMSys und mME eine wichtige Rolle bei der Neugestaltung der intelligenten Netze (Smart Grids) und des neuen Marktmodells (Smart Market). Dieser Beitrag beschäftigt sich mit den neuen Gesetzen, den Marktrollen und ihren Aufgaben, Datenschutz und Datensicherheit, dem iMSys als sichere Lösung, dem sicheren Betrieb von Smart Meter Gateways, Smart Grid - Smart Market, dem Zusammenspiel zwischen reguliertem Bereich und Markt, den Einsatzbereichen der iMSys sowie den Auswirkungen auf Prozesse und Systeme und gibt Handlungsempfehlungen.

  18. Darwin als Sehhilfe für die Psychologie - Evolutionspsychologie

    Science.gov (United States)

    Schwab, Frank

    Im Folgenden geht es um Einäugige, stereoskopisches Sehen, weite und enge Horizonte, Monokel und Sonnenbrillen. Der Beitrag versucht die Metapher des Sehens und der Sehhilfen anzuwenden, um so zu verdeutlichen, welchen Gewinn die herkömmliche Psychologie durch die Verwendung einer Darwin'schen Brille erlangen kann.

  19. Abstracts – eine facettenreiche Textsorte der Wissenschaft

    Directory of Open Access Journals (Sweden)

    Ines Busch-Lauer

    2012-01-01

    Full Text Available Der Beitrag beschreibt die Relevanz der informationsverdichtenden Textsorte Abstract in der Wissenschaftskommunikation. Im Mittelpunkt stehen die Definition, die Klassifikation und die Struktur sowie ausgewählte Merkmale dieser Textsorte.Im ersten Teil des Beitrags werden die unterschiedlichen Arten von Abstracts anhand von Textbeispielen aus der Linguistik, der Medizin und den Technikwissenschaften expliziert. Im zweiten Teil untersucht der Beitrag anhand von Abstracts, die von deutschen Studierenden der Technik- und Ingenieurwissenschaften im Rahmen ihrer fachbezogenen Englischausbildung verfasst wurden, inwieweit die textsortenimmanenten Merkmale auch von Lernenden in der Textproduktion in der Fremdsprache umgesetzt wurden. Mit dieser qualitativ beschreibenden Untersuchung trägt die Studie zur kontrastiven Fachtextsortenbeschreibung und andererseits als Praxisbericht zur Vermittlung von Textsorten im fachbezogenen Fremdsprachenunterricht an Hochschulen bei.

  20. Aussteigen aus dem Rechtsextremismus: Foto-Praxis, bildwissenschaftliche Analyse und Ausstellungsarbeit als Methoden individueller Reflexion und des wissenschaftlichen und (sozialpädagogischen Kompetenzerwerbs

    Directory of Open Access Journals (Sweden)

    Ulrike Pilarczyk

    2013-06-01

    Full Text Available Der Beitrag zeigt die medienpädagogischen und bildwissenschaftlichen Dimensionen eines zeitlich und thematisch gestaffelten Projektes auf. Ausgangspunkt war das in den Jahren 2009/10 von der Organisation EXIT-Deutschland in Berlin mit Aussteigern/-innen aus der rechtsextremen Szene initiierte Fotoprojekt «Lebensbilder». Die im Rahmen biografisch orientierter, medien- und sozialpädagogischer Fallarbeit entstandenen Fotos wurden als Prozess individueller Bilderzeugung und als Mittel zur Reflexion der jeweiligen Lebenssituation der Aussteiger(innen verstanden und eingesetzt. Eine Ausstellung schloss diese erste Phase des hier beschriebenen Projektes ab. Dem Wunsch folgend, die praktischen Erfahrungen aus der Arbeit mit Fotos wissenschaftlich überprüfen zu lassen, wurden in den Jahren 2011 und 2012 mit Studierenden am erziehungswissenschaftlichen Institut der TU Braunschweig die «Lebensbilder» zunächst einer wissenschaftlichen Bildanalyse unterzogen und anschliessend in einem gestalterisch-interpretativen Projekt durch die Studierenden zu einer Ausstellung weiterentwickelt.

  1. Coordinated powertrain control for automatic transmission systems - a contribution to making driving easier and reducing environmental pollution; Koordinierte Antriebsstrangsteuerung fuer automatische Getriebe - ein Beitrag zur Entlastung von Fahrer und Umwelt

    Energy Technology Data Exchange (ETDEWEB)

    Huelser, H.; Loeffler, J. [Robert Bosch GmbH, Stuttgart (Germany); Mies, M. [Adam Opel AG, Ruesselsheim (Germany)

    1999-07-01

    The contribution presents a coordinated powertrain control system for vehicles with automatic transmission. The control system is universally applicable with different types of engines and transmission systems. It works by selecting gears and engine torque according to the position of the driving pedal and thus optimizes fuel consumption, vehicle dynamics and emissions. The powertrain control system is integrated in the CARTRONIC system architecture which ensures simple, coordinated handling of all control systems of the vehicle. Together with a board network management system, it can be integrated into an overall system for optimisation of mechanical and electrical energy use in the vehicle. [German] Der Beitrag stellt eine Koordinierte Antriebsstrangsteuerung fuer Fahrzeuge mit automatischen Getrieben vor, die einen Verbrennungsmotor mit elektronischer Motorleistungssteuerung, eine automatisierte mechanische Kupplung bzw. eine Wandlerueberbrueckungskupplung, sowie das Getriebe steuert. Diese Steuerung ist fuer unterschiedliche Typen von Motoren und Getrieben universell einsetzbar. Die Antriebsstrangsteuerung interpretiert die Fahrpedalstellung als Fahrerwunsch nach einer Vortriebsleistung und setzt diese durch geeignete Auswahl von Gang und Motordrehmoment um. Durch eine Adaption der Gangauswahl an den Fahrertyp, die Fahrsituation und Umgebungsbedingungen wird ein optimaler Fahrzeugbetrieb hinsichtlich Kraftstoffverbrauch, dynamischem Fahrverhalten und Emissionen erreicht. Die Koordinierte Antriebsstrangsteuerung ist integriert in die CARTRONIC-Systemarchitektur, die den fahrzeugweiten Verbund der Steuerungs- und Regelungssysteme einfach handhabbar macht. So kann sie gemeinsam mit einem Bordnetz-Management in ein fahrzeugweites System zur Gesamt-Optimierung von mechanischer und elektrischer Energie integriert werden. (orig.)

  2. Was uns nicht umbringt, macht uns härter? Resilienzförderung bei armen Kindern aus Sicht des Capability-Ansatzes

    Directory of Open Access Journals (Sweden)

    Gutwald Rebecca

    2015-07-01

    Full Text Available Resilienz wird in der Psychologie und Sozialpädagogik häufig als positiv angesehen. In der Armutsbekämpfung ist diese Sichtweise durchaus nachvollziehbar, insbesondere in der Prävention von Kinderarmut: wenn Resilienz das ist, was ein Kind in die Lage versetzt, die Risiken und negativen Folgen von Armut besser zu bewältigen, scheint es sinnvoll, diese Fähigkeit bei Kindern zu fördern. Mein Beitrag befürwortet diesen Befund, plädiert aber dafür, dass die Resilienzdebatte der Untermauerung durch Argumente aus der praktischen Philosophie bedarf, da das, was häufig als Resilienz bezeichnet wird, nicht immer positiv zu bewerten ist. Ziel meines Beitrags ist es, den Resilienzdiskurs im Rahmen der Kinderarmutsbekämpfung in einer normativen Theorie zu verankern: im Capability Ansatz von Amartya Sen. Resilienz wird damit, so meine These, zu einem fundamental normativen Begriff. Mein Beitrag gliedert sich in drei Teile: Zuerst wird auf die Grundideen des CA und die Stellung von Kindheit darin eingegangen. Im zweiten Teil wird der Resilienzbegriff im Kontext von Kinderarmutsprävention charakterisiert. Der dritte Teil widmet sich den Verbindungslinien zwischen der Resilienzdiskussion und dem CA. Leitgedanke ist dabei, dass der CA die menschliche Handlungsfähigkeit als normativ grundlegend auszeichnet. Auf dieser Basis lässt sich überzeugend beurteilen, warum Armut bei Kindern höchst problematisch ist und welches Ziel in der Resilienzförderung verfolgt werden soll. Wie ich argumentieren werde, ist die Bereitstellung von capabilities auch die gerechtigkeitstheoretische Basis von Resilienzförderung in der Praxis. Der Beitrag schließt mit Impulsen, welche, so meine Hoffnung, für eine weitere Diskussion der Normativität von Resilienz dienlich sein können.

  3. Polen: ein Jahr EU-Mitgliedschaft als Erfolgsstory

    OpenAIRE

    Wilkiewicz, Zbigniew

    2005-01-01

    Aus Anlass der einjährigen EU-Mitgliedschaft Polens zieht der Beitrag eine positive Bilanz für die Wirtschaft und das Wirtschaftswachstums des Landes und zitiert einen veröffentlichten Regierungsbericht der polnischen Regierung, dem zufolge der EU-Beitritt maßgeblich zur Festigung günstiger makroökonomischer und struktureller Tendenzen im Außenhandel, auf dem Arbeitsmarkt und in der Landwirtschaft beigetragen hat. Angesichts der sehr hohen Arbeitslosenrate, der gravierenden regionalen Asymme...

  4. Ein "global orientiertes Geschichtsbewusstsein" als zukünftige Herausforderung der Geschichtsdidaktik?

    Directory of Open Access Journals (Sweden)

    Susanne Popp

    2002-07-01

    Full Text Available Für den Geschichtsunterricht, der in seinem Kerncurriculum nationalhistorisch ausgerichtet ist, stellt die Globalisierung eine große Herausforderung dar. Der Beitrag untersucht die Frage, ob und in welcher Weise die aktuelle deutsche Geschichtsdidaktik sich mit dem Thema der "Globalisierung" auseinandersetzt, und stellt die Schwierigkeiten für eine ernsthafte Annäherung an dieses Thema dar. Denn, so wird gezeigt, der Weg zu einer angemessenen geschichtsdidaktischen Antwort auf die Herausforderungen der Globalisierung kann nicht auf dem Weg zusätzlicher Inhalte gefunden werden, sondern erfordert eine konzeptionelle Herangehensweise. Deshalb skizziert der Beitrag in knapper Form neue historische Ansätze einer "globally conceptualized world history" und leitet daraus erste geschichtsdidaktische Überlegungen ab. Des weiteren werden Geschichtscurricula aus anderen Ländern, die sich mit "world history" befassen, dargestellt, diskutiert und auf Anregungen für die geschichtsdidaktische Diskussion befragt. Sie können die keine fertigen Lösungen bieten, doch Wahrnehmung der Probleme schärfen und Impulse für die geschichtsdidaktische Diskussion geben.

  5. Methoden der Kommunikations- und Mediengeschichte: die Wechselwirkung unterschiedlicher Verfahren als Spezifikum der Kommunikations- und Mediengeschichte

    NARCIS (Netherlands)

    Hemels, J.; Averbeck-Lietz, S.; Klein, P.; Meyen, M.

    2009-01-01

    Dieser Beitrag verfolgt zwei Ziele: Einerseits wird beabsichtigt, nicht his-torisch geschulte Kommunikationswissenschaftler mit Grundlagen und Praxis kommunikationswissenschaftlicher Forschung vertraut zu ma-chen. Andererseits wird für ein Zusammenspiel zwischen führenden For-schungsansätzen und

  6. The data envelopment analysis efficiency of public power suppliers. A contribution to the discussion of deregulation; Die DEA-Effizienz oeffentlicher Stromversorger. Ein Beitrag zur Deregulierungsdiskussion

    Energy Technology Data Exchange (ETDEWEB)

    Cantner, U; Hanusch, H; Westermann, G

    1994-03-01

    The emphasis of a draft on the reform of energy legislation from the Federal Ministry of Economics and the emphasis of the general discussion is the so-called third party access and unbundling as well as the new approach to the granting of regional monopolies. In the final analysis the point of all these suggestions is to unbundle supplies and make sure that more competition creates more efficiency. This contribution looks at the empirical aspects of the problem. Some public power supply companies in Germany were selected in order to identify and describe inefficiencies of public power supply in Germany. Part two briefly describes the situation on the sector of ``public power supply`` which the emphasis on the commitment of the public. Part three describes the basics of data envelopment analysis which is then used in part 4 in order to analyse power suppliers. A distinction is made between private and public industry analysis. Part 5 contains some conclusions. (orig./UA) [Deutsch] Im Zentrum des Referentenentwurfs zur Energierechtsreform des Bundeswirtschaftsministeriums sowie in der allgemeinen Diskussion stehen der sogenannte ``third party access``, das ``unbundling`` sowie die Neuregelung der Vergabe von Gebietsmonopolen. Letztendlich geht es bei all diesen Vorschlaegen darum, die Versorgungsleistungen ganz oder teilweise (``unbundling``) aus dem Schutzwall der regulierten Gebietsmonopole herauszunehmen und damit dafuer zu sorgen, dass ueber verstaerkten Wettbewerb eine effizientere Leistungserstellung bewerkstelligt wird. Der vorliegende Beitrag moechte zu diesem Problembereich von empirischer Seite aus Stellung nehmen. Mit Hilfe ausgewaehlter Unternehmen des oeffentlichen Stromversorgungssektors in Deutschland soll untersucht werden, ob und welche Ineffizienzen bei der oeffentlichen Stromversorgung auftreten. Abschnitt 2 beschreibt kurz die Situation im Sektor ``Oeffentlichen Stromversorgung``, wobei ein Schwerpunkt dessen oeffentlicher Auftrag ist. Abschnitt

  7. The Use of Qualitative Content Analysis in Case Study Research

    OpenAIRE

    Kohlbacher, Florian

    2006-01-01

    Dieser Beitrag hat zum Ziel, Möglichkeiten zu untersuchen und zu diskutieren, wie qualitative Inhaltsanalyse als (Text-) Interpretationsmethode in der Fallstudienforschung angewendet werden kann. Zunächst wird die Fallstudienforschung als eine Forschungsstrategie innerhalb der qualitativen Sozialforschung kurz dargestellt. Danach folgt eine Einführung in die (qualitative) Inhaltsanalyse als Interpretationsmethode für qualitative Interviews und anderes Datenmaterial. Abschließend wird der Eins...

  8. Autonomous intelligent cruise control (AICC) - a major contribution to the enhancement of comfort and active driving safety; Autonome Intelligente Geschwindigkeitsregelung (AICC) - ein Beitrag zur Steigerung des Komforts und der aktiven Fahrsicherheit

    Energy Technology Data Exchange (ETDEWEB)

    Dorissen, H.T.; Hoever, N.

    1996-07-01

    Within the framework of the PROMETHEUS-Project research and development work on different systems has been carried out to improve traffic efficiency, environment and safety. The Autonomous Intelligent Cruise Control has emerged as one of the projects with the brightest future. In contrast to conventional cruise control systems, the AICC system controls not only the speed of the vehicle, but also its distance to vehicles ahead. In practice this means that the driver is additionally supported by the automatic variation of the set vehicle speed according to traffic conditions. This results in a major improvement in driving comfort as well as in traffic safety. In this article, Hella describes the principal technical facts and also highlights the advantages and possible applications of the first generation of AICC. (orig.) [Deutsch] Im Rahmen des PROMETHEUS-Projektes sind unterschiedliche Systeme erforscht und entwickelt worden, um den Verkehr sicherer, umweltfreundlicher und effizienter zu gestalten. Der `Autonome Intelligente Geschwindigkeitsregler` ist hieraus als eines der zukunftstraechtigsten Projekte hervorgegangen. Ein AICC-System regelt die Geschwindigkeit sowie den Abstand zu einem vorausfahrenden Fahrzeug. Im Vergleich zum konventionellen Geschwindigkeitsregler wird der Fahrer zusaetzlich durch die automatische Anpassung der Sollgeschwindigkeit an die gegebene Verkehrssituation unterstuetzt. Dies ermoeglicht eine entsprechende Verbesserung des Fahrkomforts und letztendlich auch der Verkehrssicherheit. In diesem Beitrag zeigt Hella neben den grundsaetzlichen technischen Zusammenhaengen eine moegliche Realisierung, die Vorteile und den Nutzen fuer ein AICC-System der ersten Generation auf. (orig.)

  9. Differenz als Belastungsprobe. Verhandlungen des deutsch-jüdischen Gesprächs in Bernhard Schlinks Erzählung »Die Beschneidung«

    Directory of Open Access Journals (Sweden)

    Mirjam Bitter

    2015-05-01

    Full Text Available Schlinks Erzählung stellt anhand zweier Liebender das Scheitern eines deutsch-jüdischen Gesprächs dar und verhandelt die Frage, wie viele Differenzen eine Beziehung aushält. Die titelgebende Beschneidung tritt dabei nicht nur auf der Handlungsebene auf, wo der Protagonist durch Konversion zum Judentum die Differenz zu seiner jüdischen Freundin zu überwinden hofft. Auch auf metaphorischer Ebene problematisiert die Erzählung die ›Selbstbeschneidung‹ des Protagonisten, der aus Angst vor Tadel von jüdischen Figuren viele seiner Gedanken nicht ausspricht. Als Opfer antideutscher Vorurteile ruft er diverse antisemitische Stereotype auf. Der Beitrag geht der Frage nach, inwiefern die Erzählung damit für solch stereotypes Gedankengut sensibilisiert und subtil gegen einen antisemitischen und revisionistischen Diskurs anschreibt oder inwiefern sich der Text vielmehr in einen solchen Diskurs einschreibt.

  10. Politische Bildung im Kontext von Regierung, Unterricht und Zucht

    Directory of Open Access Journals (Sweden)

    Thomas Rucker

    2014-02-01

    Full Text Available Johann Friedrich Herbart (1776-1841 gilt als der Begründer der wissenschaftlichen Pädagogik. In diesem Beitrag wird zu zeigen versucht, dass Herbart die Unterstützung politischer Bildung als eine Aufgabe von Regierung, Unterricht und Zucht bestimmt und in seinem Werk wichtige „Bausteine“ für eine Theorie der politischen Bildung unter den Bedingungen von Erziehung vorlegt hat. Nach Herbart ist das politische Selbst- und Weltverhältnis auf Sachverhalte bezogen, die nicht nur die Lebensführung einzelner Menschen, sondern die Lebensführung einer Mehrzahl von Menschen betreffen. Nicht das Zusammenleben von Menschen generell ist jedoch Orientierungsgesichtspunkt des politischen Selbst- und Weltverhältnisses, sondern nur das problematisch gewordene Zusammenleben. Politik ergibt sich nach Herbart aus einem Konflikt hinsichtlich der Frage, wie das Zusammenleben von Menschen geregelt sein sollte. Während die Regierung lediglich mittelbar einen Beitrag zur politischen Bildung leistet, indem sie die Voraussetzungen für Unterricht und Zucht bereitstellt, fungieren die beiden zuletzt genannten Formen von Erziehung als die eigentlichen Medien, in denen die politische Bildung im Sinne Herbarts ihren Ort hat.

  11. Das Re-entry von Kritik: Assemblageforschung nach der Kritik an der Kritik. Kommentar zu Alexa Färbers „Potenziale freisetzen“

    Directory of Open Access Journals (Sweden)

    Hanna Göbel

    2014-05-01

    Full Text Available Der Kommentar zum Beitrag von Alexa Färber diskutiert eine Vermengung von drei unterschiedlichen Kritikbegriffen sowie Orten von Kritik in der aktuellen Debatte um die Assemblageforschung im Feld der Urban Studies. Ich rekonstruiere und unterscheide zwischen einem Kritikbegriff als theoretischer Norm, wie er von der (neo-marxistischen Stadt- und Raumforschung vertreten wird, und der ontologischen Kritik dieser Norm seitens der Assemblageforscher_innen. Alexa Färbers Beitrag zeigt drittens exemplarisch eine sich einschleichende normative Ebene in der Assemblageforschung auf, die bislang als Kritikform unterbelichtet geblieben ist. Diese wird als Wiedereinführung (re-entry von empirisch vollzogener Kritik in die Assemblageforschung bezeichnet. Damit ist eine theoretische Neupositionierung von Kritik ‚innerhalb’ einer Assemblage gemeint, indem Kritik nicht mehr als theoretische Norm ‚außerhalb’ zu verorten ist. In diesem Kommentar plädiere ich dafür, in der Assemblageforschung eine differenzierte Auseinandersetzung mit unterschiedlichen Begriffen und Orten von Kritik zu pflegen, um innerhalb der Urban Studies und für interessierte städtische Akteure mit urbaner Expertise (u.a. Architekt_innen, Planer_innen, Künstler_innen, Aktivist_innen, Kultur- und Sozialarbeiter_innen, DIY-Gemeinschaften klarer adressierbar zu sein.

  12. Die Künstlerin als Arbeiterin (an der Gesellschaft. Lu Märtens zeitgemässe Betrachtungen zur Ökonomie der namenlosen Genialität The Woman Artist at Work. Lu Märten’s up-to-date Reflections on the Economy of the Nameless Genius

    Directory of Open Access Journals (Sweden)

    Verena Kuni

    2002-03-01

    Full Text Available In einem Reprint der Originalausgabe von 1919 endlich wieder zugänglich gemacht, empfiehlt sich Lu Märtens kleine Schrift Die Künstlerin nicht nur als Beitrag zur Vor- und Frühgeschichte der feministischen Kunstwissenschaft. Als historisch-kritische Analyse der Ökonomie künstlerischer Arbeit unter besonderer Berücksichtigung der Geschlechterdifferenz kann das Büchlein auch für aktuelle Debatten wichtige Denkanstösse liefern.Lu Märten’s essay, Die Künstlerin, now available as a reprint of the first edition published in 1919, is to be recommended not only as an important contribution to feminist art history avant la lettre. Moreover, the historical-critical analysis of the economy of artistic production which pays special attention to gender differences offers plenty of inspiration for current debates and reflections.

  13. Hilfe oder Hindernis? Meinungen finnischer Sprachstudierender über Mehrsprachigkeit als Ressource beim Deutschlernen

    Directory of Open Access Journals (Sweden)

    Sabine Grasz

    2017-10-01

    Full Text Available Der Fremdsprachenunterricht in Finnland befindet sich gerade in einer Umbruchphase, denn mit der Einführung neuer Lehrpläne im Jahr 2016 werden Verfahren der Mehrsprachigkeitsdidaktik in Zukunft eine zentrale Rolle spielen. In diesem Beitrag wird untersucht, ob und wie finnische Universitätsstudierende, die selbst von einer eher monolingual ausgerichteten Lerntradition geprägt sind, ihr mehrsprachiges Repertoire als Ressource beim Lernen weiterer Fremdsprachen sehen. Zu diesem Zweck wurde eine Befragung unter Lehramtsstudierenden der Fächer Anglistik und Skandinavistik, die Germanistik als Nebenfach studieren möchten, durchgeführt. Die Analyse zeigt, dass die Studierenden zwar mehrheitlich positive Einstellungen gegenüber Mehrsprachigkeit aufweisen, dass es aber Entwicklungsbedarf im Hinblick auf Sprachbewusstheit, multilinguale Fähigkeiten und bei den Einstellungen gegenüber Sprachmischungen gibt. Foreign language education in Finland is currently undergoing a period of change, as the introduction of new curricula in 2016 will lead to a central role of multilingualism in teaching. This article examines whether and how Finnish university students, who themselves were influenced by a more monolingual learning tradition, consider their multilingual repertoire as a resource for learning other foreign languages. For this purpose, a survey was conducted among teacher students of English and Swedish, who would like to study German as a minor. The analysis shows that while the majority of students have positive attitudes towards multilingualism, there is a need for development in terms of language awareness, multilingual skills, and attitudes towards language mixes.

  14. Do We Need a New Approach to Library and Information Science?

    OpenAIRE

    Audunson, Ragnar Andreas

    2018-01-01

    Der vorliegende Beitrag analysiert den durch die Digitalisierung bedingten Druck auf das Bibliothekswesen und die Bibliotheks- und Informationswissenschaft sowie auf die zunehmende Bedeutung der Bibliotheken als Begegnungsorte und -arenen für die Öffentlichkeit. Beide Entwicklungstendenzen stellen die Notwendigkeit von Bibliothekaren als Vermittler zwischen Nutzern und Informationsquellen in Frage. Das Navigieren und Suchen nach Informationen in einer digitalen Welt, wenn die Welt selbst eine...

  15. Modulare und durchgängige Produktmodelle als Erfolgsfaktor zur Bedienung einer Omni-Channel-Architektur - PLM 4.0

    Science.gov (United States)

    Golovatchev, Julius; Felsmann, Marcus

    Mit der Transformation der Wertschöpfungsstrukturen von Utility 1.0 zu Utility 4.0 erfolgt offensichtlich auch eine Veränderung des Produkts. Vor dem Hintergrund disruptiver Technologien (IoT, Big Data, Cloud, Robotics etc.) und auch gesellschaftlicher Veränderungen entstehen ständig neue Geschäftsmodelle und Produkte, die über die reine Versorgungsdienstleistung (z. B. Strom) hinausgehen. Dabei muss der wertvolle Rohstoff Produktdaten für smarte Produkte durchgängiger und schneller nutzbar gemacht werden. Die modularen und durchgängigen Produktstrukturen leisten einen Beitrag zur Beherrschung von Komplexität und stellen somit einen wesentlichen Hebel für erfolgreiche Produktentwicklung und -management dar. In diesem Beitrag werden Ansätze beschrieben, wie es den vor der Herausforderung Utility 4.0 stehenden Unternehmen gelingen kann, Smart-Energy-Produkte so zu modellieren, dass sie die Interoperabilität der einzelnen Produktionsmodule sicherstellt und ein Ende-zu-Ende-Management ermöglicht.

  16. Der Gewalt ihre Freiheit - Der Horror-Film als jugendliches Wertekonstrukt

    Directory of Open Access Journals (Sweden)

    Gudrun Marci-Boehncke

    2010-06-01

    Full Text Available Jugendliche Gewaltbereitschaft wird in der medienkritischen Diskussion nicht selten auf mediale Vorbilder zurück geführt. Anhand qualitativer Daten wird zum einen gezeigt, dass das Erkennen medialer Gewalt in Sprache und Handlung bildungsabhängig ist, zum anderen, dass Jugendliche nach eigenen Angaben aus sehr unterschiedlichen Gründen zur Gewalt bereit wären – etwa, um Freunde zu verteidigen. Besonders betrachtet werden dann Jugendliche, die gern Horrorfilme anschauen. Die Untersuchung zeigt, dass die Fans von Horrorfilmen eine Rezeptionshaltung einnehmen, die zwischen Angst-Lust und Distanz oszilliert. Es interessieren hier keine identifikatorischen Aspekte, sondern Jugendliche haben Spaß an den medialen Inszenierungen des Gruseligen. Jenseits medienmoralischer Warnungen plädiert der Beitrag – unter Verweis auch auf Rezeptionstheorien der Literaturwissenschaft – dafür, distanzierten Horror-Genuss als Spielform nicht zu überbewerten und ihn auch als Ausdruck elaborierter Lese- und Medienkompetenz zu verstehen. Whereas within media-critical discussions violence of teens is sometimes said to be produced by referent power of media, this paper presents empirical data which show that and how teens are able to assume a distance when viewing media violence in horror-films. What they feel is not empathy, but fun. Young people enjoy a kind of delightful horror for themselves and are able to step into distance while talking to peers about their impressions during reception. This way of “delightful horror” is not only a phenomenon of modern media reception but can be found in recent and established horror literature. In so far this article encourages a more relaxed way of judging young people’s media habits.

  17. "BiC in Sustainability?" : die Transparenz von Best in Class-Nachhaltigkeitsfonds in Deutschland

    OpenAIRE

    Schäfer, Henry; Bauer, Fabian; Bracht, Felix

    2015-01-01

    Der vorliegende Beitrag analysiert in Deutschland vertriebene Publikumsinvestmentfonds, die den Anspruch als Nachhaltigkeitsfonds erheben und nach dem Best in Class-Ansatz (BiC-Ansatz) in Kombination mit einem Negative-Screening (verstanden als Ausschlusskriterien) konstruiert sind. Ziel ist es zu erheben, auf welche Weise die den Fonds vom Anbieter zugrunde gelegten BiC- und Screening-Methoden Anlegern transparent gemacht werden und worin zwischen den Fonds diesbezüglich Unterschiede bestehe...

  18. Die Potenziale des Deprival Value-Konzepts zur entscheidungsorientierten Bewertung von Kapital in liberalisierten Netzindustrien

    OpenAIRE

    Weiß, Hans-Jörg

    2005-01-01

    Die Liberalisierung der Netzindustrien hat das Interesse an den konzeptionellen Grundlagen der Kapitalkostenermittlung wiederbelebt. Im Mittelpunkt dieses Beitrags steht eine dieser Grundlagen: Das Deprival Value-Konzept. Es wird aufgezeigt, dass es sich hierbei um ein ökonomisch fundiertes Bewertungskonzept handelt, das sich sowohl in stationären als auch in nicht-stationären Bewertungskontexten konsistent als Referenzpunkt verwenden lässt. Die Kontextabhängigkeit der Deprival Value-Ermittlu...

  19. Was bedeutet Trägheit? Begriff und Wirkung der Trägheit im Rahmen des Wechselverhaltens von Konsumenten im Strommarkt

    NARCIS (Netherlands)

    Henseler, Jörg

    2006-01-01

    In Wissenschaft und Praxis wird die Trägheit der Konsumenten als Ursache der geringen Wechselrate im deutschen Strommarkt für Haushaltskunden diskutiert. Der vorliegende Beitrag arbeitet heraus, dass es sich bei dieser Argumentation entweder um eine Tautologie oder ein Synomym für den Verbleib in

  20. Dimensioning of activation systems using submerged membranes at municipal sewage treatment plants; Bemessung von Membranbelebungsanlagen beim Einsatz zur Reinigung kommunaler Abwaesser

    Energy Technology Data Exchange (ETDEWEB)

    Ohle, P.; Dorgeloh, E. [Technische Hochschule Aachen (DE). Inst. fuer Siedlungswasserwirtschaft (ISA)

    1999-07-01

    Dimensioning of conventional activation systems in Germany as a rule relies on instruction sheet A131 of the Abwassertechnische Vereinigung or follows the Hochschulgruppen approach (HSG). They contain recommendations as to the size of the nitrification and denitrification zones, the amount of oxygen supplied and sludge production, and the size of the final sedimentation tank. For the use of sludge activation techniques by means of submerged membranes at municipal sewage treatment plant there so far do not exist any clues to dimensioning that make allowance for the modified boundary conditions. The present paper analyses instruction sheet A131 for its suitability as a basis in the dimensioning of sludge activation systems with submerged membranes at municipal sewage treatment plant. Then the dimensioning instructions are modified to suit the changed boundary conditions, and recommendations for the dimensioning of activation systems with submerged membranes on the basis of extensive studies carried out at the Institut fuer Siedlungswasserwirtschaft ISA of Aachen Technical University RWTH are given. (orig.) [German] Die Bemessung konventioneller Belebungsverfahren erfolgt in Deutschland i.d.R. auf der Grundlage des Arbeitsblatts A 131 der Abwassertechnischen Vereinigung bzw. nach dem Hochschulgruppenansatz (HSG). Sie enthalten Empfehlungen bezueglich der Dimensionierung von Nitrifikations- und Denitrifikationszone, Sauerstoffversorgung, Schlammproduktion und Nachklaerbecken. Fuer den Einsatz von Membranbelebungsanlagen in kommunalen Klaeranlagen existieren bislang keine Bemessungshinweise, die den veraenderten Randbedingungen Rechnung tragen. Der vorliegende Beitrag analysiert das Arbeitsblatt A 131 in Hinsicht auf die Moeglichkeit zur Anwendung fuer die Bemessung von Membranbelebungsanlagen beim Einsatz zur kommunalen Abwasserreinigung. Im Weiteren erfolgt die Modifikation der Bemessungshinweise hinsichtlich der geaenderten Randbedingungen und die Angabe von

  1. Wie können Corporate Citizens voneinander lernen? : Ordonomische Anregungen für inter-organisationales Lernen im Global Compact der Vereinten Nationen

    OpenAIRE

    Hielscher, Stefan; Pies, Ingo; Beckmann, Markus

    2009-01-01

    "Der Global Compact der Vereinten Nationen versteht sich nicht als Regulierungsinitiative, sondern als freiwilliges Lern- und Dialogforum für Corporate Citizenship. Dieser Beitrag entwickelt Vorschläge, wie der Global Compact diesem Anspruch (noch besser) gerecht werden kann. Hier geht es um Strukturen in zweifacher Hinsicht: (a) Zum einen können Corporate Citizens besonders gut dann voneinander lernen, wenn sie sich über die strukturellen Bedingungen erfolgreicher - aber auch: fehlgeschlagen...

  2. Lesekompetenz im Französisch als 1. und 2. Fremdsprache in einer mehrsprachigen Perspektive bei Primarschüler/innen am Ende der 6. Klasse

    Directory of Open Access Journals (Sweden)

    Giuseppe Manno

    2017-04-01

    Full Text Available Im Beitrag werden Resultate eines laufenden Forschungsprojekts vorgestellt, das die Lesekompetenz im Französisch als 1. und 2. Fremdsprache (Umkehrung der bisherigen Reihenfolge durch die Fremdsprachenreform in der Schweiz unter Berücksichtigung der Schulsprache Deutsch in einer mehrsprachigen Perspektive am Ende der Primarstufe (6. Klasse untersucht. Die zentrale Fragestellung ist, ob die Schüler/innen mit Französisch als 1. Fremdsprache über eine bessere Lesekompetenz verfügen als mit Französisch als 2. Fremdsprache (jeweiliger Beginn: 5. Klasse. Des Weiteren wird der Zusammenhang zwischen der Französischlesekompetenz und der Schulsprache untersucht. Für die Überprüfung dieser Fragestellungen liegt ein quasi-experimentelles Design vor, bei dem beide Gruppen zeitverschoben gemessen wurden. In this article we will present some results of an ongoing project which studies the reading comprehension in French at the end of primary school (6th grade as first and as second foreign language (reversal of the previous order in the current reform of the foreign languages in Switzerland by also considering the school language (German within a multilingual approach. The focus of this article is whether learners with French as second foreign language reach a higher proficiency than learners with French as first foreign language (French being still taught from grade 5 on. Furthermore we will study the correlation between the reading comprehension proficiency in French and in German. The quasi-experimental research design is given by the fact that classes in the old and new system could be recorded at different times.

  3. Der digitalisierte Forscher

    Directory of Open Access Journals (Sweden)

    Storr, Stefan

    2017-12-01

    Full Text Available Der vorliegende Kommentar bezieht sich auf den Beitrag „Der digitalisierte Forscher“ von Thomas Kröll (ALJ 2/2017, 71. Ausgehend von der Beschreibung der gegenwärtigen Gesellschaft als Wissensgesellschaft werden drei Aspekte angeführt, die die Wissenschaft als System heute kennzeichnen und künftig weitere Bedeutung haben werden: die Gewinnung und Weitergabe von Forschungsdaten, die Bewertung von wissenschaftlichen Leistungen und die Funktion von Universitäten. Der Kommentar schließt mit der Aufforderung, das Grundrecht der Wissenschaftsfreiheit als institutionelle Garantie fortzuentwickeln.

  4. Vermögensmaximierung durch Stiftungen als Unternehmensträger? Eine Analyse der Steuerwirkungen

    OpenAIRE

    Franke, Günter; Herrmann, Markus

    1993-01-01

    Einige große deutsche Unternehmen werden von privaten gemeinnützigen Stiftungen getragen. Dies wirft die Frage auf, weshalb eine solche Lösung der üblichen Vorgehensweise, bei der natürliche Personen Gesellschafter eines Unternehmens sind, vorgezogen wird. In diesem Beitrag wird untersucht, ob und unter welchen Voraussetzungen der Hauptgesellschafter einer Kapitalgesellschaft das Vermögen seiner Erben erhöhen kann, indem er seine Gesellschaftsanteile einer gemeinnütziger Stiftung überträgt un...

  5. Polilingvizmas kaip „grįžimas namõ“: tarp Babilono katastrofos ir Jeruzalės Sekminių stebuklo. Vlado Braziūno poezijos at(sivėrimai | Der Polylinguismus als „Rückkehr nach Hause“: zwischen der babylonischen Katastrophe und dem Pfingstwunder von Jerusalem

    Directory of Open Access Journals (Sweden)

    Skirmantas Valentas

    2006-01-01

    Full Text Available In diesem Beitrag wird ein Versuch unternommen, die Widerspiegelung von zwei philologisch wichtigen Episoden der Heiligen Schrift in der modernen Poesie zu vermitteln. Es geht um die Erzählung von der babylonischen Sprachenverwirrung im Buch der Anfänge und um das in den Apostelgeschichten erwähnte Pfingstwunder, die beide unter einen Begriff Polylinguismus fallen.Der Polylinguismus in der Poesie ist als eine syntagmatische Mehrsprachigkeit, anders gesagt, als eine implizite Benennung desgleichen Denotats in einigen Sprachen, zu betrachten.Der verallgemeinernde Begriff „Rückkehr nach Hause“ lässt zwei Begriffe in Verbindung setzen: die sich nach der babylonischen Katastrophe etablierte Mehrsprachigkeit und das Pfingstwunder als eine Möglichkeit die verwirrten Sprachen wieder zu einem Harmonischen zusammenzufügen.Da die Poesie als ein Grammatik modellierender Text vorliegt, ist eine Idee hervorzuheben, dass neben einer üblichen Sprache in der Poesie eine andere Sprache mit völlig anderen Regeln aufgedeckt werden muss.Als eines der Grundmerkmale der üblichen Sprache ist ein in ihr enthaltenes Oppositionsystem zu betrachten. Als Grundmerkmal einer anderen Sprache gilt dagegen das Schwinden der grundlegenden Oppositionen, das einen endlosen und periodischen Text schafft.Der Polylinguismus der Poesie wird in den linguistischen Geschichten am deutlichsten sichtbar. Der Polylinguismus in der Poesie, der dem Simultandolmetschen nahsteht, führt uns auf das Pfingstwunder zurück.

  6. Die Rule of Law im Völker- und im Europarecht – aktuelle Probleme. Gegenwärtige Herausforderungen und Chancen für die EU als eine "Union des Rechts"

    Directory of Open Access Journals (Sweden)

    Andreas J. Kumin

    2015-10-01

    Full Text Available Bei diesem für die Schriftfassung geringfügig adaptierten Artikel handelt es sich um die am 5. März 2015 in Graz gehaltene Antrittsvorlesung eines Praxisprofessors, der im Hauptberuf Leiter der Abteilung für Europarecht im Völkerrechtsbüro des österreichischen Außenministeriums ist. Im Anschluss an den Beitrag von Helmut Tichy (in ALJ 1/2015, 176–185, der sich auf das Völkerrecht und die internationalen Beziehungen konzentriert, setzt sich der vorliegende Artikel mit aktuellen Herausforderungen und Chancen der EU als „Union des Rechts“ auseinander. Dabei wird auf die Stärkung der Wahrung der Grundwerte und Rechtsstaatlichkeit in den EU-Mitgliedstaaten, den EU-Beitritt zur Europäischen Menschenrechtskonvention, die Sicherung einer wirksamen und leistungsfähigen EU-Gerichtsbarkeit sowie die Gewährleistung einer angemessenen demokratischen Mitbestimmung auf allen Stufen der Rechtsetzung eingegangen.

  7. Fallstudien als Forschungsmethode: Plädoyer für einen Methodenpluralismus in der deutschen betriebswirtschaftlichen Forschung

    OpenAIRE

    Göthlich, Stephan E.

    2003-01-01

    Qualitative Forschungsmethoden stehen in den Wirtschaftswissenschaften noch immer im Schatten quantitativer Methoden und ökonomischer Modelle. Dies gilt insbesondere für die deutsche Forschung, während sich international eine zunehmende Öffnung zu qualitativen Methoden abzeichnet. In diesem Beitrag wird die Auffassung vertreten, dass sich die deutsche Forschung diesem Trend nicht verschließen sollte, will sie den Anschluss nicht verlieren. Exemplarisch für qualitative Forschungsmethoden werde...

  8. Zusammenarbeit aus Sicht eines outgesourcten Instandhalters

    Science.gov (United States)

    Grüßer, Stefan; Loeven, Heinz-Wilhelm

    Dauerhafter Unternehmenserfolg ist nur mit einer fortschrittlichen Instandhaltung zu erzielen. Durch den enormen Kostendruck infolge der Globalisierung und die Innovationssprünge auf der technischen Seite wird auch die Frage nach der modernen Organisationsform für die Instandhaltung gestellt. Eine Möglichkeit der Kostenoptimierung ist das Outsourcing von Instandhaltungsleistungen. Hierbei ist es unerlässlich, dass sich die Mitarbeiter zum Dienstleister entwickeln. In diesem Beitrag wird die Entwicklung der InfraServ Knapsack von einer internen Instandhaltungsabteilung hin zu einem Industriellen Dienstleister beschrieben und Aspekte der Zusammenarbeit mit externen Kunden aus der Sicht des outgesourcten Instandhalters geschildert. Es werden die wichtigen Entwicklungsschritte zur Dienstleistungsorientierung der früheren Eigeninstandhaltung aufgezeigt. Dieser Beitrag ist nicht als "Königsweg“ zu verstehen, er soll vielmehr anhand der Erfahrungen einer outgesourcten Eigeninstandhaltung Anregungen für die Entwicklung der eigenen Instandhaltungsorganisation liefern.

  9. Darwinische Kulturtheorie - Evolutionistische und "evolutionistische`` Theorien sozialen Wandels

    Science.gov (United States)

    Antweiler, Christoph

    Evolutionistische Argumentationen außerhalb der Biologie sind weit verbreitet. Wenn sie vertreten werden, heißt das mitnichten, dass sie notwendigerweise von darwinischen Argumenten geprägt sind. Wenn man Evolution und Kultur aus explizit darwinischer Perspektive zusammen bringt, bedeutet das noch lange nicht unbedingt Soziobiologie. Und es bedeutet sicherlich nicht Sozialdarwinismus. Dieser Beitrag soll einen Überblick der so genannten evolutionären Ansätze bzw. evolutionistischen Ansätze zu menschlichen Gesellschaften bzw. Kulturen geben. Es soll gezeigt werden, was in den Ansätzen analytisch zu trennen ist und was synthetisch zusammen gehört. Mein Beitrag ist nicht wissenschaftsgeschichtlich angelegt, sondern systematisch ausgerichtet und hat zwei Schwerpunkte (Antweiler 2008; Antweiler 2009b). Zum einen geht es um kausale Zusammenhänge von organischer Evolution und gesellschaftlichem Wandel. Auf der anderen Seite werden Analogien zwischen biotischer und kultureller Evolution erläutert, die als spezifische Ähnlichkeiten dieser beiden als grundsätzlich verschieden gesehenen Prozesse aufgefasst werden. Dadurch wird die Frage aufgeworfen, ob die Evolution von Organismen einerseits und die Transformation von Gesellschaften bzw. Kulturen andererseits, spezielle Fälle eines allgemeinen Modells von Evolution darstellen.

  10. The contribution of diffusion to methane transport in deep underground gas deposits; Der Beitrag der Diffusion zum Methantransport in tiefliegenden Gas-Lagerstaetten

    Energy Technology Data Exchange (ETDEWEB)

    Sachs, W. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany)

    1998-12-31

    Optimisation of gas production necessitates accurate knowledge of gas transport mechanisms. In view of the extreme temperatures, pressures, and permeability conditions of underground gas deposits, linear transfer of existing knowledge will be inappropriate. The author therefore uses a simple capillary bundle model with exemplary pressures, temperatures and permeabilities in order to assess the contribution of transport by diffusion. The diffusion coefficients, which are required for this and so far could not be measured under pressure, were determined by a new experimental method whose results will permit a better interpretation of the concentration dependence of the diffusion coefficient. The velocity of methane inflow and outflow in the water-filled pore space may provide knowledge on problems of gas storage in the pore space. (orig.) [Deutsch] Fuer den Foerderprozess und insbesondere seine Optimierung ist eine genaue Kenntnis der Transportmechanismen wesentlich. Unter den drastischen Bedingungen fuer Temperatur, Druck und Permeabilitaet tiefliegender Gas-Lagerstaetten mag die Uebertragung der bisherigen Vorstellungen ueber den Transport in der Lagerstaette zu einer unvollstaendigen Beschreibung fuehren. Unter Anwendung eines einfachen Kapillarbuendelmodells wird mit Beispielen fuer Druck, Temperatur und Permeabilitaet der moegliche Beitrag des Transports durch Diffusion abgeschaetzt. Zur Bestimmung der hierfuer notwendigen und bisher unter Druckbeaufschlagung nicht gemessenen Diffusionskoeffizienten wurde eine neue experimentelle Methode angewandt, deren Ergebnisse eine weiterfuehrende Interpretation der Konzentrationsabhaengigkeit des Diffusionskoeffizienten ermoeglichen. Auch fuer Fragestellungen der Speicherung von Gas im Porenraum kann die Geschwindigkeit der Ein- und Ausloesung von Methan im wasserhaltigen Porenraum von Interesse sein. (orig.)

  11. Ausländerfeindlichkeit unter Jugendlichen in Leipzig

    OpenAIRE

    Petermann, Sören; Goldenberg, Olga

    2017-01-01

    In kommunalen Umfragen erhobene Einstellungen gegenüber Ausländern repräsentieren ein Bild gelebter Toleranz. Selten werden Jugendliche zu ihren ausländerbezogenen Einstellungen gefragt und mit altersspezifischen Faktoren in Verbindung gesetzt. Dieser Beitrag bezieht sich auf theoretische Ansätze der Anomietheorie, der Sozialisations- und Deprivationsforschung, um Kompensationsprozesse und Konfliktpotenziale als Wirkungsmechanismen für Ausländerfeindlichkeit unter Leipziger Jugendlichen zu un...

  12. Kurz zum Klima: Schatzsuche im Ozean – liegt die Zukunft des Bergbaus am Meeresgrund?

    OpenAIRE

    Albrecht-Saavedra, Jutta; Lippelt, Jana; Maierhofer, Leon

    2013-01-01

    Angesichts stark wachsender Nachfrage nach Rohstoffen, insbesondere vonseiten der aufstrebenden Schwellenländer und entsprechend steigender Rohstoffpreise, richtet sich der Blick zunehmend auf die Tiefsee als enorme noch weitgehend unerschlossene Quelle reichhaltiger Rohstoffvorkommen. Der KZK-Beitrag gibt einen Überblick über die Lagerstätten, die Erkundung und die geplante Erschließung der Tiefseeressourcen und weist auf die Risiken eines Ressourcenabbaus in der Tiefsee hin.

  13. Die Auswirkungen von Corporate Social Responsibility und Organisationsstolz auf Mitarbeiter im Kundenkontakt

    OpenAIRE

    Rhein, Miriam Katharina

    2012-01-01

    Corporate Social Responsibility (CSR) leistet nicht nur einen Beitrag zum Wohle verschiedener Stakeholdergruppen, sondern kann sich über die Wahrnehmungen der Mitarbeiter positiv auf den Unternehmenserfolg auswirken. Es kann angenommen werden, dass eine von den Mitarbeitern als glaubwürdig wahrgenommene CSR das Potenzial besitzt, kurzfristige, äußerst intensive positive emotionale sowie längerfristig anhaltende einstellungsbezogene Reaktionen hervorzurufen und dadurch relevante Verhaltensweis...

  14. Stufenweise Integration von eLearning an der Technischen Universität München

    Science.gov (United States)

    Pätzold, Sebastian; Graf, Stephan; Gergintchev, Ivan; Pongratz, Hans; Rathmayer, Sabine

    Der vorliegende Beitrag beschreibt als Best Practice Beispiel die stufenweise Integration eines Learning Management Systems (LMS) in die Infrastruktur von Information und Kommunikation (IuK) der Technischen Universität München (TUM). Dabei wird sowohl die Konsolidierung mehrfach angebotener Funktionalitäten und Dienste in den verschiedenen Portalen der Universität als auch die sukzessive Optimierung der Abläufe aufgezeigt. Gleichzeitig wird auf zukünftige weitere Entwicklungen hin zu einer vollständigen Integration der IuK, aber auch auf die Probleme in den unterschiedlichen Stadien der Entwicklung eingegangen.

  15. Medienpädagogik unter der differenztheoretischen Lupe. Eine Identitätssuche zwischen Disziplin und Profession

    Directory of Open Access Journals (Sweden)

    Franziska Linke

    2017-09-01

    Full Text Available Der Beitrag diskutiert die dem Themenheft zugrundeliegende Fragestellung nach der Konstitution der Medienpädagogik aus einer systemtheoretischen Perspektive. Dabei wird im Anschluss an Stichweh (2013 Ansatz der funktionalen Differenzierung ein Untersuchungsrahmen aufgezeigt, der es ermöglicht, die Medienpädagogik sowohl aus wissenschaftssoziologischer als auch professionssoziologischer Perspektive zu betrachten. Gerade die zentrale Rolle der (digitalen Medien für Lern- und Bildungsprozesse sowie für den Arbeitsmarkt (u. a. KMK 2016 verlangt eine stetige Reflexion professioneller Handlungssysteme der Medienpädagogik, die nicht losgelöst von der Frage nach dem Selbstverständnis der Medienpädagogik als Wissenschaftsdisziplin gelingen kann (u. a. Hugger 2001. Divergierende theoretische Positionierungen der Akteurinnen und Akteure sowie verschiedene Zielvorstellungen zur Medienpädagogik selbst und zu dem, was sie praktisch leisten kann, erschweren ein solches Vorhaben. Die Autorinnen des Beitrags begeben sich daher, unter Berücksichtigung der Differenzierung zwischen Disziplin und Profession, auf die Suche nach möglichen Antworten. Vorgeschlagen wird eine erweiterte Betrachtungsweise, welche die Medienpädagogik als wissenschaftliche Produktionsgemeinschaft beschreibt und dadurch Potenziale eröffnet theoretische und empirische Erkenntnisse von Akteurinnen und Akteuren unterschiedlicher wissenschaftlicher Disziplinen mit Medienzusammenhang zu berücksichtigen. Ferner wird dargelegt, dass ein solcher Beschreibungsansatz neue Forschungsperspektiven auf die professionstheoretische Einordnung praktischer Handlungssysteme der Medienpädagogik eröffnen kann.

  16. Medienkompetenz - Anmerkungen anlässlich einer Untersuchung der Medienkompetenz von und durch SchülerInnen an Neuen Mittelschulen in Wien.

    Directory of Open Access Journals (Sweden)

    Christian Swertz

    2016-06-01

    Full Text Available Im Beitrag wird vorgeschlagen, Medienkompetenz auch als Ordnungsbegriff zu verstehen. Dazu wird eine präskriptive, eine empirische und eine selektive Ordnung unterschieden. Mit einer induktiv-empirischen Untersuchung wird demonstriert, dass so ein Beitrag zum Verständnis des Medienkompetenzbegriffs geleistet werden kann, mit dem zugleich eine Kritik deduktiv-empirischer Ordnungen erreicht wird. Dabei wird gezeigt, dass ein Bezug auf aktuelle materielle Zeichenträger zugleich problematisch und notwendig ist. It is suggested to understand media literacy as an ordering term. A prescriptive, an empirical and a selective order are distinguished. In an inductive-empirical study it is shown, that this perspective can contribute to an understanding of media literacy and to a critical reflection of deductive-empirical orders. While doing so it is shown, that relating media literacy to contemporary material sign vehicles is problematic and necessary at the same time.

  17. Qualitative Forschung mit lebenslimitierend erkrankten Kindern und Jugendlichen: Hören wir richtig hin?

    Directory of Open Access Journals (Sweden)

    Claudia Oetting-Roß

    2016-05-01

    Full Text Available Der nachfolgende Beitrag diskutiert die Herausforderungen des Einbezugs von betroffenen Kindern und Jugendlichen in die qualitative Forschung zum Thema lebenslimitierende Erkrankungen insbesondere unter dem Blickwinkel der methodischen Gestaltung dieses Einbezugs. Hierfür wird zunächst die Lebens- und Versorgungssituation lebenslimitierend erkrankter Kinder und Jugendlicher dargestellt. Anschließend werden Ergebnisse aus empirischen Studien erläutert und im Hinblick auf die Herausforderungen einer Beteiligung erkrankter Kinder, Jugendlicher und ihrer Familien diskutiert. Als Ergebnis dieser Analyse erfolgt eine Zusammenfassung zentraler Diskussionsstränge. Zudem werden Strategien für eine sensible Integration von schwerkranken Kindern und Jugendlichen abgeleitet und auf der Basis bestehender Erfahrungen aus qualitativen Studien konkretisiert. Vor dem Hintergrund einer laufenden Studie mit lebenslimitierend erkrankten Kindern liefert der Beitrag Anregungen für die methodische Planung, Durchführung und Evaluation von entsprechenden Forschungsvorhaben. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1602241

  18. Sprüche, Sentenzen, Zitate als Kurzformen oder "einfache Formen" der Textsorten in interkultureller Sicht

    Directory of Open Access Journals (Sweden)

    Mirko Križman

    1998-12-01

    Full Text Available Eine systematische sprachliche Behandlung der Sprichwörter in bezug auf die verschiedenen Sprachen und auf die sprachliche Varianz nur einer Sprache wäre eine umfangreiche Arbeit. Man kann aber doch in einem Beitrag, wo zwei oder drei Sprachen in Betracht gezogen werden, zuerst einige allgemeine Feststellungen erwähnen, womit die Varianz, die in den Bereich der Sprachwissenschaft gehört, einigermaßen prinzipiell zu lösen wäre und etliche Details der Stilistik (auch im ästhetischen Sinn gezeigt werden können.

  19. Des Widerspenstigen Zähmung: subjektives Alter(n), qualitativ erforscht

    OpenAIRE

    Graefe, Stefanie

    2013-01-01

    "Der Beitrag präsentiert Forschungsergebnisse einer qualitativen Interviewstudie zur subjektiven Alter(n)serfahrung von Menschen in der zweiten Lebenshälfte sowie aus dem Forschungsprozess resultierende Überlegungen zur Frage, wie sich die soziale Erfahrung Alter(n) methodologisch konzeptualisieren und empirisch erforschen lässt. Die Auswertung erfolgte angelehnt an die Grounded-Theory- Methodologie. Ausgehend von der 'relativen (subjektiven) Alterslosigkeit' als fallübergreifender Schlüsselk...

  20. Des Widerspenstigen Zähmung: Subjektives Alter(n), qualitativ erforscht

    OpenAIRE

    Graefe, Stefanie

    2013-01-01

    Der Beitrag präsentiert Forschungsergebnisse einer qualitativen Interviewstudie zur subjektiven Alter(n)serfahrung von Menschen in der zweiten Lebenshälfte sowie aus dem Forschungsprozess resultierende Überlegungen zur Frage, wie sich die soziale Erfahrung Alter(n) methodologisch konzeptualisieren und empirisch erforschen lässt. Die Auswertung erfolgte angelehnt an die Grounded-Theory- Methodologie. Ausgehend von der "relativen (subjektiven) Alterslosigkeit" als fallübergreifender Schlüsselka...

  1. Vielfalt oder Chaos? 'Musikalische Bildung' und das künstlerisch-wissenschaftliche Studium

    OpenAIRE

    Kremer, Joachim

    2013-01-01

    Der folgende Beitrag konzentriert sich auf die Hochschule als Raum für gelebte und gelehrte Diversität. Er widmet sich der Diversität im künstlerisch-wissenschaftlichen Studium der Schulmusik, diskutiert die Frage, inwieweit die Vielfalt der Studienpläne der Zieldimension 'musikalische Bildung' zuträglich ist und entwirft ein Studien-Szenario, das verstärkt interdisziplinäre Synergien fordert. (DIPF/Orig.)

  2. Publikationsunterstützung: Die Bibliothek ist nicht genug

    Directory of Open Access Journals (Sweden)

    Christian Kaier

    2017-06-01

    Full Text Available Für wissenschaftliche Bibliotheken bedeutet der Aufbau publikationsunterstützender Services eine lohnende Erweiterung ihres Aufgabengebietes, die auf ihren traditionellen Kompetenzen aufbaut. Um überzeugende und umfassende Services zum Thema wissenschaftliches Publizieren anbieten zu können ist es jedoch notwendig, noch stärker als bisher mit verschiedensten Partnern zusammenzuarbeiten. Dieser Beitrag legt dar, welche Kompetenzen es zu entwickeln und welche Partner es vorrangig anzusprechen gilt.

  3. Challenging the Dualistic Assumptions of Academic Writing: Representing Ph.D. Research As Embodied Practice

    OpenAIRE

    Hanrahan, Mary

    2003-01-01

    Dieser Beitrag befasst sich mit der Spannung zwischen der dualistischen Tradition unseres Kulturkreises (WERTHEIM, 1999) einerseits und neueren Ansätzen, die die Konstruktion und Genese von Wissen als leibgebundenes Handeln innerhalb biologischer und ökologischer Systeme nachzuvollziehen versuchen andererseits (z.B. DAMASIO, 1994; LEAR, 1998; LEMKE, 1995; MATURANA & VARELA, 1992). Dabei werden auch Implikationen eines biosozialen Modells für Forschungsmethodologie und für akademisches Schreib...

  4. Schreiben auf Deutsch in Japan : Abstufung zwischen akademisch und wissenschaftlich

    OpenAIRE

    Schmidt, Maria Gabriela

    2013-01-01

    In dem Beitrag wird zunächst eine Unterscheidung von akademischem und wissenschaftlichem Schreiben aus didaktischen Gründen vorgeschlagen. Für den Fremdsprachenunterricht Deutsch als Fremdsprache in Japan ist darüberhinaus der Einfluss eigenkultureller Textmusterkonvention zu beachten. „Akademisches Schreiben“ lehnt sich an die englische Bezeichnung „academic writing“ an. In der deutschsprachigen Literatur findet sich häufig „wissenschaftliches Schreiben“, mit dem man ein hohes sprachliches N...

  5. Beeinflussung der Wirkung von Ernährungsinformation durch Framing: Analyse am Beispiel von Folsäure

    OpenAIRE

    Lensch, Kathrin; Hartmann, Monika; Simons, Johannes

    2011-01-01

    Die Bereitstellung und verbrauchergerechte Aufbereitung von Informationen stellt eine Möglichkeit dar, Konsumenten darin zu unterstützen, Gesundheitsaspekte vermehrt in das Kauf- und Essverhalten zu integrieren. In der Verhaltensökonomik gelten Framing-Effekte als wichtige Bestimmungsfaktoren für die Wahrnehmung von Informationen. Im Rahmen des vorliegenden Beitrags werden Framing-Effekte am Beispiel von Ernährungsinformationen über Folsäure mit Hilfe eines Experiments untersucht. Die Ergebni...

  6. Geschwisterbeziehungen in der Verarbeitung sexueller Traumatisierung: Der Film "Das Fest"

    OpenAIRE

    Sohni, Hans

    2001-01-01

    Filme reizen als Gegenstand psychoanalytischer Kunstinterpretation durch ihre strukturelle Nähe zum "szenischen Verstehen" und bereichern unsere Einsicht in menschliche Beziehungen. Der Film "Das Fest" lohnt wegen seiner besonderen ästhetischen Form und wegen seiner Aussage zur Geschwisterbeziehung. Nach filmjournalistischer Einschätzung zeigt er die Demontage der bürgerlichen Gesellschaft und die Reinszenierung destruktiver Gewalt. In der Interpretation dieses Beitrags führt der Film dagegen...

  7. Review: Anja Weiß (2001). Rassismus wider Willen. Ein anderer Blick auf eine Struktur sozialer Ungleichheit

    OpenAIRE

    Bremer, Helmut

    2002-01-01

    Die Arbeit liefert einen Beitrag zur Debatte um Rassismus und Interkulturalität sowie zur Anwendung qualitativer Forschungsverfahren im Rahmen der Theorie BOURDIEUs. Rassismus und Anti-Rassismus werden nicht isoliert betrachtet, sondern als eine Dimension sozialer Ungleichheit, die in eine umfassende Theorie sozialer Ungleichheit eingebunden werden muss. Vorgeschlagen wird BOURDIEUs Konzept von Habitus, Feld und Kapital. Das ermöglicht einen anderen Blick auf das Phänomen. Rassismus reproduzi...

  8. Arbeit und Liebe: Wie die soziale Organisation der Geschlechterverhältnisse in beiden Bereichen zu Machtunterschieden zwischen Frauen und Männern führt

    OpenAIRE

    Kupfer, Antonia

    2017-01-01

    "Gegenstand dieses Beitrags ist die soziale Organisation der Geschlechterverhältnisse als Hierarchie zwischen Männern und Frauen vorwiegend in westlichen Ländern. Auf der Grundlage eines dualisierenden Denkmodells werden Frauen von Männern instrumentalisiert, ausgegrenzt und diskriminiert. Im Bereich der Arbeit manifestiert sich das in einer geschlechtsspezifischen Arbeitsteilung, der Vergeschlechtlichung von Tätigkeiten und Berufen, einer gläsernen Decke für Frauen in höheren Erwerbsposition...

  9. PET activation in basal ganglia disorders: Parkinson`s disease and dystonia; PET-Aktivierungsstudien bei Basalganglienerkrankungen: Morbus Parkinson und Dystonien

    Energy Technology Data Exchange (ETDEWEB)

    Ceballos-Baumann, A.O. [Neurologische Klinik, Technische Univ. Muenchen (Germany); Boecker, H. [Neurologische Klinik, Technische Univ. Muenchen (Germany); Conrad, B. [Neurologische Klinik, Technische Univ. Muenchen (Germany)

    1997-03-01

    This article reviews PET activation studies with performance of different motor paradigms (joy-stick movements, imagination of movement, writing) in patients with movement disorders. The focus will be on Parkinson`s disease (PD) and dystonia. PET findings will be related to clinical and electrophysiological observations. PET activation studies before and after therapeutic interventions such as pallidotomy in Parkinson`s disease and botulinum toxin in writer`s cramp are described. The contribution of PET activation studies to the understanding of the pathophysiology of dystonia and PD is discussed. (orig.) [Deutsch] Der Beitrag beschreibt verschiedene PET-Aktivierungsstudien mit motorischen Paradigmen (`joystick`-Bewegungen, Vorstellung von Bewegung, Schreiben) bei Bewegungsstoerungen, im wesentlichen bei Patienten mit Dystonie, einer Hyperkinese, und Morbus Parkinson als Hypokinese. Die experimentellen Befunde werden mit der Klinik in Bezug gebracht. Neue Untersuchungen vor und nach therapeutischen Interventionen, wie die stereotaktische Pallidotomie bei Parkinson und die Botulinum-Toxin-Therapie bei Schreibkrampf, werden beschrieben. Der Beitrag von PET-Aktivierungsstudien zum Verstaendnis der Pathophysiologie von Bewegungsstoerungen wird diskutiert. (orig.)

  10. Das Zur Sprache Kommen deprivilegierter Subjektivität in der digital medialen Kultur. Inklusionstheoretische Perspektiven der Medienpädagogik

    Directory of Open Access Journals (Sweden)

    Ulas Aktas

    2017-04-01

    Full Text Available Will sich die Medienpädagogik den aktuellen gesellschaftlichen Herausforderungen stellen, wie sie durch die UN-BRK zu einer zentralen Aufgabe gegenwärtiger pädagogischer Auseinandersetzung geworden ist, stellt sich mit Nachdruck die Frage nach einer inklusionstheoretischen Grundierung der Medienpädagogik, ebenso wie nach einer systematischen medienpädagogischen Perspektive auf inklusive Handlungsfelder. Der Beitrag erarbeitet für beides Grundlagen. Auf der Basis poststrukturalistischer und postkolonialer Diskurstheorien und dem inklusionstheoretischen Trilemma von Mai-Anh Boger wird sowohl eine inklusionstheoretische Grundierung der Medienpädagogik als auch eine systematische Perspektive auf inklusive Handlungsfelder entfaltet. Der Beitrag stellt hierfür die Frage nach der Entstehung deprivilegierter Subjektivität in den Mittelpunkt. Ausgehend von Michel Foucault und Gayatri Spivak wird mit Blick auf deprivilegierte Subjektvität gefragt, inwieweit wer an einer Rede teilhaben bzw. (in seiner Eigensprachlichkeit gehört werden kann. Hierfür wird das Konzept gebrochener Subjektivität entfaltet und die Chancen, die eine medienpädagogische Forschung zu Gesichtspunkten der Inklusion hat, herausgestellt. Abschliessend werden die drei inklusiven Handlungsfelder der Medienpädagogik systematisch dargestellt und das Konzept der «prekären medialen Selbst-Bezeugung» als Heuristik für das ‹Zur Sprache Kommen› deprivilegierter Subjektivität entfaltet.

  11. Soziologische Wissenskulturen zwischen individualisierter Inspiration und prozeduraler Legitimation. Zur Entwicklung qualitativer und interpretativer Sozialforschung in der deutschen und französischen Soziologie seit den 1960er Jahren

    Directory of Open Access Journals (Sweden)

    Reiner Keller

    2016-01-01

    Full Text Available Wie wissen Soziologinnen und Soziologen, was sie wissen? Trotz der Internationalisierung der Soziologie bestehen nach wie vor starke sprachräumliche Unterschiede in der soziologischen Wissensproduktion, in eingesetzten Theorien, Methoden und Fragestellungen. Der nachfolgende Beitrag erläutert die Entwicklung und Ausprägung der Unterschiedlichkeit soziologischer Wissenskulturen im Hinblick auf den Einsatz qualitativer bzw. interpretativer Ansätze seit den 1960er Jahren in Deutschland und Frankreich. Er stützt sich auf ein von uns 2012-2014 geleitetes Forschungsprojekt und dessen empirische Grundlagen: Dokumentenanalysen und Interviews. Wissenskulturen werden als die Arten und Weisen der Produktion und Legitimation von (hier: soziologischem Wissen verstanden. Diesbezüglich lässt sich von der Erkenntnisproduktion als dem zentralen Handlungsproblem soziologischen Forschens sprechen. Während für die französischsprachige Soziologie diagnostisch von einer Lösung dieses Erkenntnisproblems durch die den Forschenden zugeschriebenen Kompetenzen und Inspirationen ausgegangen werden kann, schiebt sich im deutschsprachigen Raume eine prozedurale Legitimation durch Verfahren in den Vordergrund. Der Beitrag rekonstruiert exemplarisch die Ausgangssituation dieser Entwicklungen um die Wende zu den 1960er Jahren und bettet sie in die weitere Entfaltung der jeweiligen Soziologien ein. Er will damit zur gegenwärtigen Entwicklung einer reflexiven Soziologie beitragen. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1601145

  12. Nudges, Recht und Politik: Institutionelle Implikationen

    Directory of Open Access Journals (Sweden)

    Lepenies Robert

    2016-07-01

    Full Text Available In diesem Beitrag argumentieren wir, dass eine umfassende Implementierung sogenannter Nudges weitreichende Auswirkungen für rechtliche und politische Institutionen hat. Die wissenschaftliche Diskussion zu Nudges ist derzeit hauptsächlich von philosophischen Theorien geprägt, die im Kern einen individualistischen Ansatz vertreten. Unsere Analyse bezieht sich auf die Art und Weise, in der sich Anhänger des Nudging neuster Erkenntnisse aus den Verhaltenswissenschaften bedienen – immer in der Absicht, diese für effektives Regieren einzusetzen. Wir unterstreichen, dass die meisten Nudges, die derzeit entweder diskutiert werden oder bereits implementiert sind, nicht Teil eines Rechtssystems sind und keinen normativen Charakter haben. Dazu unterscheiden wir zwischen zwei Idealtypen, um menschliches Verhalten zu beeinflussen, die wir als normativ bzw. instrumentell bezeichnen. Diese Idealtypen stehen für verschiedene Weisen, in denen öffentliche Regeln strukturiert werden können; sie erlauben uns, die institutionellen Implikationen von Nudges zu verstehen und zu bewerten. Hier betonen wir den Wert des Rechts als Absicherung gegenüber den möglichen schädlichen Konsequenzen von in der Politik und Regierungsführung eingesetzten Nudges. Unser Beitrag schließt mit Reaktionen auf einige Einwände, die unsere Vorschläge bereits erhalten haben.

  13. Frauen mit Eßstörungen im Ausdauersport

    OpenAIRE

    Bös, Annette

    2003-01-01

    Die vorliegende Arbeit untersucht das Phänomen Eßstörungen bei Ausdauersportlerinnen. Auf dem Hintergrund des identitätstheoretischen Ansatzes von Stahr et al. (1995) geht es um die Frage nach den Hauptverursachungsmomenten der Eßstörungen von sieben jungen Sportlerinnen. Im Rahmen einer qualitativen Sozialforschungsarbeit wurden sieben Athletinnen in einem problemzentrierten Interview zur Phase ihrer Eßstörungserkrankung befragt. Die Arbeit setzt sich zum Ziel, einen Beitrag zur systematisch...

  14. Sinnvolle Lebensführung im Spannungsfeld von Risiko und Sicherheit Die Ethik der Risikominimierung im Lichte von Kierkegaards und Nietzsches Kritik der Moderne

    Directory of Open Access Journals (Sweden)

    Hüsch Sebastian

    2016-07-01

    Full Text Available Der Beitrag betrachtet die für die Gegenwartsgesellschaft charakteristische Orientierung an Sicherheit und Risikovermeidung vor dem Hintergrund der Reflexionen Søren Kierkegaards und Friedrich Nietzsches bezüglich der Abgründigkeit der menschlichen Existenz. Die Untersuchung wirft die Frage auf, ob die Suche nach einem im alltäglichen Sinne verstandenen „guten Leben“ letzten Endes zu Lasten der Möglichkeiten einer als sinnhaft erlebten Existenz geht.

  15. Ausbau der ganztägigen Kindertagesbetreuung kann zur Zufriedenheit von Müttern beitragen

    OpenAIRE

    Stahl, Juliane F.; Schober, Pia S.

    2016-01-01

    Eltern mit Kindern, die noch nicht zur Schule gehen, stehen bei der Vereinbarkeit von Familie und Beruf vor besonderen Herausforderungen. Um diese Eltern besser zu unterstützen, hat die Politik sowohl den Ausbau von Plätzen in der öffentlichen Kindertagesbetreuung (Kita) forciert als auch ein bedarfsorientiertes Angebot an Ganztagsplätzen gesetzlich verankert. Der vorliegende Beitrag untersucht auf Basis von Daten des Sozio-oekonomischen Panels (SOEP) und der Stichprobe 'Familien in Deutschla...

  16. Konstitutionsmöglichkeiten und Begründungszusammenhänge von Medienpädagogik

    OpenAIRE

    Alexander Schmölz; Sabine Krause

    2017-01-01

    Dieser Beitrag verortet Medienpädagogik im Feld der Wissenschaften. Es wird die Frage diskutiert, inwieweit ein eigenständiger Zugang der Medienpädagogik zu ihren Forschungsanliegen als grundlegend für die Konstitution einer wissenschaftlichen Disziplin gilt bzw. geltend gemacht werden kann. Dazu werden, erstens, allgemeine Konstitutionsmöglichkeiten einer Disziplin schematisch aufgezeigt und ihre je unterschiedlichen Begründungszusammenhänge für wissenschaftliche Disziplinen diskutiert, um –...

  17. Projekt Multimedia Storytelling. Konzeption und Umsetzung einer Content-Marketing-Plattform an der ETH-Bibliothek

    OpenAIRE

    Kyburz, Deborah

    2017-01-01

    Storytelling begeistert und macht als Methode von sich Reden. Die ETH-Bibliothek bediente sich des Storytelling für die Entwicklung und Umsetzung einer neuen Content-Marketing-Plattform namens Explora. Erzählt werden dort Geschichten zu digitalisierten Beständen der Sammlungen und Archive und zu Dienstleistungen der ETH-Bibliothek. Im Zentrum steht hierbei die Frage der attraktiven Präsentation des (Multimedia-)Contents. Der Beitrag skizziert, warum Storytelling und Wissenschaft eine geeignet...

  18. Lateral strukturierte Oberflächen zur THz-Strahlmanipulation

    OpenAIRE

    Jahn, David; Koch, Martin (Prof. Dr.)

    2018-01-01

    Die Terahertz-Zeitbereichsspektroskopie ist mittlerweile eine etablierte spektroskopische Methode im Frequenzbereich von 0;2 THz bis etwa 5 THz. Mit der stetigen Verbesserung von Zeitbereichs-Spektrometern, in den letzten Jahren hauptsächlich vorangetrieben durch die Verbesserung der Materialsysteme sowohl im photoleitenden Emitter als auch im Detektor sind heute Systeme mit bis zu 90 dB SNR und 4;5 THz Brandbreite verfügbar. Auch der Einfluss anderer Systemkomponenten, deren Beitrag zum...

  19. Kriegs- und Generationszeugen: Adrienne Thomas und Vera Brittain // Generation and War Witnesses: Adrienne Thomas and Vera Brittain

    OpenAIRE

    Zitzlsperger, Ulrike

    2016-01-01

    Im Vordergrund stehen in diesem Beitrag Autorinnen, die sich in den dreißiger Jahren kritisch mit dem Ersten Weltkrieg und seinen Folgen auseinandersetzten. Am Beispiel von Adrienne Thomas ("Die Katrin wird Soldat") und Vera Brittain ("Testament of Youth") soll untersucht werden, wie die erklärte Zugehörigkeit von Frauen zur 'Lost Generation' mit der aktiven Kriegsteilnahme als Krankenschwester und einem differenzierten Patriotismusverständnis verbunden wurde. Auffallend sind dabei nicht nur ...

  20. Disposal of sewage sludge - problems and options; Klaerschlammentsorgung - Probleme und Moeglichkeiten

    Energy Technology Data Exchange (ETDEWEB)

    Kobelt, G.

    2000-06-01

    Sewage sludge production cannot be avoided. In consequence, the sewage sludge produced must either be utilised or combusted for heat and power generation. [German] Da Klaerschlaemme bei der Abwasserreinigung zwangsmaessig anfallen, ist ihre Vermeidung im Sinne des Paragraphen 4 (1), 1 des KrW/AbfG nicht moeglich. Deshalb muss es das Ziel einer vernuenftigen und geordneten Klaerschlammwirtschaft sein, den groesstmoeglichen Anteil des gesamten Schlammaufkommens, wie es das Gesetz ebenfalls vorschreibt, stofflich zu verwerten oder zur Gewinnung von Energie zu nutzen (energetische Verwertung). (orig.)

  1. The EEG as an instrument of the Federal areal management of renewable energies - also a contribution to the discussion about energy sectoral planning; Das EEG als Instrument des Bundes zur raeumlichen Steuerung der erneuerbaren Energien - zugleich ein Beitrag zur Diskussion um eine Energiefachplanung

    Energy Technology Data Exchange (ETDEWEB)

    Gruener, Anna-Maria [Stiftung Umweltenergierecht, Wuerzburg (Germany); Sailer, Frank [Stiftung Umweltenergierecht, Wuerzburg (Germany). Forschungsgebiet Energieanlagen- und Infrastrukturrecht

    2016-05-15

    The areal management of the power generation structure takes place at first glance mainly on the Zoning and Planning Law, less than the energy law. The only sporadically encountered jurisprudential work for controlling effect of the EEG came to the conclusion, the current configuration of the support system in the EEG is in deficit and ''blind'' to the localization and areal distribution of energy generation plants in the Federal territory, although the EEG is representing a ''downright predestined management tool''. On closer inspection, however, shows that individual provisions have entirely certain location preferences or cause areal distribution effects and the EEG thus play a management effect. The contribution is therefore devoted to the question of whether and how the EEG 2014, with the overall network expansion and payment system is able to manage the energy production from renewable energy sources in the area and whether an energy specialist planning is useful and necessary. [German] Die raeumliche Steuerung der Energieerzeugungsstruktur findet auf den ersten Blick vornehmlich ueber das Raumordnungs- und Planungsrecht statt, weniger ueber das Energierecht. Die allenfalls vereinzelt anzutreffenden rechtswissenschaftlichen Arbeiten zur Steuerungsleistung des EEG kommen zu dem Ergebnis, die jetzige Ausgestaltung des Foerdersystems im EEG sei defizitaer und ''blind'' gegenueber der Lokalisierung und raeumlichen Verteilung von EE-Anlagen im Bundesgebiet, obwohl das EEG doch ein ''geradezu praedestiniertes Steuerungsinstrument'' darstelle. Bei naeherer Betrachtung zeigt sich jedoch, dass einzelne Regelungen durchaus bestimmte Standortpraeferenzen aufweisen bzw. raeumliche Verteilungseffekte bewirken und dem EEG damit eine steuernde Wirkung zukommt. Der Beitrag widmet sich daher der Frage, ob und wie das EEG 2014 sowie das allgemeine Netzausbau- und -entgeltsystem die Energieerzeugung

  2. Das Passepartout und der Zwischenraum zwischen den Sternen: Thomas Ruff – Ein Ausstellungsrundgang um ein Projekt der Annäherung!

    Directory of Open Access Journals (Sweden)

    Jürgen Stöhr

    2013-07-01

    Full Text Available Bildbetrachtung und insbesondere die Anschauung von Kunstwerken bedürfen einer näher zu bestimmenden «visuellen Kompetenz». Je nach methodologischer Ausrichtung wird diese Kompetenz eher als bildexternes historisch-kontextuelles Fachwissen oder eher bildimmanent als Fähigkeit zum «Lesen» oder zur «ästhetischen Erfahrung» von Einzelwerken angesetzt. Der vorliegende Beitrag untersucht spielerisch die Dynamiken einer visuellen Kompetenz, die zwischen diesen beiden Polen ausgehandelt wird. Als Beispiel wurde eine Bildserie des Düsseldorfer Fotokünstlers Thomas Ruff ausgewählt. Hierbei handelt es sich um im weitesten Sinne «postmoderne» Kunst-Fotografie, die insofern die Fragen nach der Kompetenz im Umgang mit fotografischer Bildlichkeit explizit aufwirft, als Ruffs Arbeiten ihre Rezeption vermutlich selbst thematisieren und innerbildlich zu reflektieren scheinen.

  3. Bakteriochlorophyllvorstufen und Pigment-Protein-Komplexe in Rhodospirillum rubrum ST3 und GN11

    OpenAIRE

    Hammel, Jörg U.

    2006-01-01

    In der vorliegenden Arbeit wurden zwei Mutanten des Alpha-Proteobakteriums Rhodospirillum rubrum untersucht, die im Bakteriochlorophyll-Biosyntheseweg unterbrochen sind, um einen Beitrag zum genaueren Verständnis der Biosynthese dieser Moleküle und der einzelnen daran beteiligten Schritte zu liefern. Von den beiden Stämmen ST3 und GN11 wurden die ins Kulturmedium ausgeschiedenen Pigmente aufgereinigt und spektroskopisch analysiert. Ebenfalls wurden sowohl von ST3, als auch von GN11 die in int...

  4. Climate and transportation; Klima und Verkehr

    Energy Technology Data Exchange (ETDEWEB)

    Fabian, P. [Muenchen Univ. (Germany). Lehrstuhl fuer Bioklimatologie und Immissionsforschung

    1996-06-01

    This short contribution discusses emissions of the transportation sector, i.e. the global problem of carbon dioxide emissions and the regional ecological problem of nitric oxide, VOC and CO photosmog emissions. Reduction strategies are discussed. (RHM) [Deutsch] Im vorliegenden, kurzen Beitrag wird auf die Emissionen des Verkehrs, die Emissionen von CO{sub 2} - ein globales Klimaproblem - sowie die Emission von NO{sub x}, VOCs und CO-Photosmog als regionals Umwelt- und Klimaproblem eingegangen. Abschliessend werden Reduktionsstrategien dieskutiert. (RHM)

  5. Ontologische und epistemologische Grundlagen qualitative Forschung

    OpenAIRE

    Vasilachis de Gialdino, Irene

    2009-01-01

    Dieser Beitrag zielt auf das Herzstück qualitativer Forschung, indem gezeigt wird, dass es – aus der Perspektive einer Epistemologie des "gewussten" Subjekts – erforderlich ist, zunächst deren ontologische und dann deren epistemologische Grundlagen neu zu überdenken. Hierzu zeichne ich in einem ersten Schritt den Weg von einer Epistemologie des "bewussten" Subjekts hin zu einer Epistemologie des "gewussten" Subjekts nach, die ich als neuen (und nicht exklusiven) Weg des Wissens vorschlage. Da...

  6. Consumption 3.0: A web-based proposal for supporting social and ecological awareness in private consumption

    Directory of Open Access Journals (Sweden)

    Alexander Petring

    2013-03-01

    Full Text Available Angesichts der zunehmender ökologischer Herausforderungen und sich verschärfender sozialer Problemlagen in vielen Ländern der Welt wurde zuletzt intensiv über Chancen und Risiken der Einbeziehung privater Konsumhandlungen bei der Lösung der Nachhaltigkeitsproblematik diskutiert. Dieser Beitrag knüpft an diese Debatte an und macht einen konkreten Vorschlag, wie das Internet stärker als bisher dazu genutzt werden könnte, sozial-ökologische Kriterien bei Konsumentscheidungen zu stärken.

  7. Konkurrenz oder Kooperation? Zur Entwicklung des Verhältnisses von Medienbildung und informatischer Bildung

    Directory of Open Access Journals (Sweden)

    Gerhard Tulodziecki

    2016-10-01

    Full Text Available Mit der gegenwärtigen Diskussion um Mediatisierung und Digitalisierung ist die Forderung verbunden, der Medienbildung und/oder der informatischen Bildung ein größeres Gewicht in der schulischen Bildung zu verschaffen. Dies legt die Frage nahe, wie ein produktives Verhältnis zwischen beiden gestaltet werden sollte und wie beide am besten zu einer zeitgemäßen Bildung beitragen können. Bei entsprechenden Überlegungen spielen unter anderem Entwicklungen eine Rolle, die sich seit frühen Forderungen nach einer Computerbildung im Verhältnis zur damaligen Medienerziehung herausgebildet haben. In dem vorliegenden Beitrag werden solche Entwicklungen skizziert und Schlussfolgerungen für die gegenwärtige Diskussion formuliert. Dabei kommen unterschiedliche Auffassungen zur bildungsbezogenen Auseinandersetzung mit Medien sowie mit Informations- und Kommunikationstechnologien in den Blick. Für das Verhältnis von Medienbildung und informatischer Bildung ergibt sich als zentrale Schlussfolgerung, dass sowohl eine Integration der informatischen Bildung in die Medienbildung als auch eine umgekehrte Lösung unangemessen erscheint, wiewohl beide Bereiche auf Anteile aus dem jeweils anderen Bereich angewiesen sind. Danach werden für eine Medienbildung mit informatischen Anteilen ein geeigneter Medienbegriff und eine tragfähige Bildungsauffassung sowie ein Ansatz zu einem inhaltlich-thematischen Kompetenzrahmen beschrieben. Überlegungen zur schulischen Umsetzung schließen den Beitrag ab.

  8. Amerikanisierung durch Internationalisierung: Die Expansion der International Communication Association (ICA

    Directory of Open Access Journals (Sweden)

    Thomas Wiedemann

    2016-12-01

    Full Text Available Basierend auf der Soziologie Bourdieus problematisiert dieser Beitrag die Bemühungen der International Communication Association (ICA, sich über die Öffnung ihrer Führungsetage für Wissenschaftler außerhalb der USA in eine wahrhaft internationale Fachgesellschaft zu verwandeln und der Herausforderung einer global vernetzten Disziplin zu begegnen. Geleistet werden soll so ein kritischer Beitrag zur Selbstreflexion der Kommunikationswissenschaft, zu verstehen als Deutungsangebot und Ausgangspunkt für die wissenschaftliche Diskussion. Die Untersuchung von Habitus und Kapital der 29 ICA-Präsidenten und ICA Fellows aus der internationalen Scientific Community zeigt, dass die weltweit größte kommunikationswissenschaftliche Fachgesellschaft trotz der Ausweitung ihrer Führungsriege immer noch deutlichen US-Einflüssen unterliegt. Die neuen ICAWürdenträger, die für nationale und fachliche Vielfalt stehen sollen, stammen aus Weltregionen, die eine besondere Nähe zu den Vereinigten Staaten auszeichnet, und wurden an US-Universitäten sozialisiert oder stark von der US-amerikanischen Forschungstradition geprägt. Ausnahmen („Einkäufe“ von führenden Vertretern anderer Fachgesellschaften oder alternativer Paradigmen bestätigen die Regel. Die Internationalisierung der ICA-Führungsetage veränderte demzufolge weniger den Machtpol im Fach als vielmehr die Kommunikationswissenschaft weltweit. Zwar gelangten neue Perspektiven ins Zentrum der Disziplin. Im Gegenzug fand jedoch eine Amerikanisierung nationaler Felder statt, allen voran durch ICA Fellows als Vorbilder im Kampf um wissenschaftliches Kapital. Die Bemühungen der ICA, sich durch die Expansion ihrer Führungsriege zu internationalisieren, dürften somit die Machtstrukturen im Fach weiter verfestigt haben.

  9. Naturalismus als Herausforderung für den Religionsunterricht

    Directory of Open Access Journals (Sweden)

    Christian Feichtinger

    2015-11-01

    Full Text Available ENGLISH: This paper reflects on statements and attitudes of pupils in religion classes that represent a perspective of naturalism, and on teachers’ possibilities of reacting to such statements. We define the term ‘naturalism’ and explain, in which way naturalistic attitudes may occur and which questions they are related to. Based on a theological and philosophical criticism of naturalism we want to encourage teachers of religion to openly question such worldviews. To do so, we refer to the concept of ‘philosophy/theology for children/adolescents’. We argue to use the so-called ‘Socratic Method’ in its original sense, namely the challenging of alleged certainties (elenchus. The Socratic Method can and should be used not only to philosophize freely, but also to question pupils’ (naturalistic worldviews and attitudes, not with the purpose to then impose a ‘correct’ worldview onto them, but to help deconstructing alleged certainties and opening new horizons of thought. DEUTSCH: Der Beitrag befasst sich mit naturalistischen Aussagen und Einstellungen von SchülerInnen im Religionsunterricht und einer didaktischen Reflexion über den angemessenen Umgang mit ihnen durch die Lehrperson. Es wird dargelegt, was unter Naturalismus zu verstehen ist, auf welche Weise er im Unterricht auftauchen kann und welche Fragen davon betroffen sind. Gestützt auf eine theologisch-philosophische Kritik am Naturalismus sehen wir es als Aufgabe des Religionsunterrichts an, naturalistische Einstellungen kritisch zu hinterfragen. Hierzu beziehen wir uns auf das Konzept der ‚Kinder-/Jugendtheologie‘ bzw. im Speziellen auf eine ‚Theologie für Kinder/Jugendliche‘. Dabei plädieren wir dafür, die sog. ‚sokratische Methode‘ in ihrem ursprünglichen Sinn, nämlich der Infragestellung von vermeintlichen Gewissheiten (elenchus, zu verwenden. Die sokratische Methode kann und soll auch dafür verwendet werden, (naturalistische Weltsichten der Sch

  10. Die Rolle des Gerichtsdolmetschers - Experte oder notwendiges Übel?

    DEFF Research Database (Denmark)

    Christensen, Tina Paulsen

    2012-01-01

    Die Zahl der gedolmetschten Gerichtsverhandlungen steigt weiterhin in vielen Rechtssystemen, weshalb es immer wichtiger wird, dass Rechtssysteme über qualifizierte Dolmetscher verfügen. In Dänemark begegnen Richter, die Rezipienten von Gerichtsdolmetschleistungen sind, sowohl professionellen als...... auch nicht- oder semi-professionellen Gerichtsdolmetschern. Dies lässt vermuten, dass die Richter in der Praxis Dolmetschleistungen von sehr unterschiedlicher Qualität erleben und vermutlich kein einheitliches Bild von der Rolle des Gerichtsdolmetschers haben. Ziel der Studie, die ich in diesem Beitrag...

  11. Lernerfolg und Kompetenz bewerten. Didaktische Potenziale von Portfolios in Lehr-/Lernkontext

    Directory of Open Access Journals (Sweden)

    Jörg Stratmann

    2009-12-01

    Full Text Available Mit der Diskussion um die Berücksichtigung von Kompetenzen in Schule und Hochschule ergeben sich für Lehrende neue Aufgaben. Es geht nicht mehr nur darum, Lehrinhalte zu benennen, sondern auch darum, wozu Lernende als Ergebnis des Lernprozesses in der Lage sein sollen. Der vorliegende Beitrag möchte eine Übersicht über aktuelle Nutzungsvarianten und die damit verbundenen Potentiale geben und ein Analyseraster vorstellen, mit dem Szenarien beschrieben und verglichen werden können.

  12. Die Generation Y – Ein Plädoyer für die Analyse einer „vernetzten Generation“ zur Weiterentwicklung der Bibliotheksdidaktik

    Directory of Open Access Journals (Sweden)

    Kim Farah Giuliani

    2017-04-01

    Full Text Available Dieser Beitrag greift sowohl den wissenschaftlichen Diskurs über die „Generation Y“ als auch Aspekte der Vermittlung von Informationskompetenz in Bibliotheken auf. Beide Themen werden verknüpft und in Bezug auf eine erfolgreiche Bibliotheksdidaktik diskutiert.   This article takes up both the scientific discourse about the Millenials (Generation Y as well as the debate on how to impart information literacy and library didactics. Both topics are discussed in combination, with respect to successful didactics in libraries.

  13. Über 20 Jahre ARIADNE. Die frauenspezifische Information und Dokumentation der Österreichischen Nationalbibliothek

    Directory of Open Access Journals (Sweden)

    Lydia Jammernegg

    2016-09-01

    Full Text Available 1992 wurde Ariadne als Fraueninformations- und -dokumentationsstelle an der Österreichischen Nationalbibliothek (ÖNB eingerichtet und arbeitet seitdem sowohl an der dokumentarischen Aufarbeitung des aktuellen frauen-, geschlechterrelevanten und feministischen Literaturbestandes als auch an der Sichtbarmachung des historischen Bestandes der ÖNB zu diesem Themenbereich. In diesem Beitrag geht es darum, die Position von Ariadne im Fraueninformations- und -dokumentationswesen, als Teil der ÖNB, an der Schnittstelle zur Frauenszene, Frauenbewegung, feministischen Szene und zur Frauen- und Geschlechterforschung einer Reflexion zu unterziehen. Nach einer mehr als 20-jährigen Tätigkeit soll ein Rückblick in die Geschichte zeigen, was Ariadne geleistet hat und wo Grenzen liegen, welche Ansprüche und Anliegen Ausgangspunkte für die Arbeit waren und wofür es heute noch frauenspezifische Informations- und Dokumentationseinrichtungen wie Ariadne braucht.

  14. Digitalisierung als Inkubator für die Energieversorgung von morgen

    Science.gov (United States)

    Arnold, Christian; Postina, Matthias

    Neue Treiber der Digitalisierung bestimmen die Geschicke der etablierten Unternehmen im Energiebereich, dabei haben diese in vielen Fällen noch nicht einmal adäquat auf die altbekannten Treiber der Energiewende reagiert. Eine ganze Branche ist im Umbruch, alte Erlösmodelle brechen ein und Einigkeit scheint bei den Verantwortlichen nur in der Frage zu herrschen, wie in Zukunft noch Geld verdient werden kann. Dieser Beitrag erklärt die prägenden Treiber der Veränderung, analysiert die Ausgangslage und nennt Herausforderungen der Branche. Darüber hinaus legt er den Fokus auf die Betrachtung der neuen digitalen Wertschöpfung. Dazu wird ein Modell eingeführt, welches von der klassischen Wertschöpfungskette über datenbasierte Geschäftsmodelle im Energiesystem bis hin zum Internet of Smart Services reicht. Mit dem Modell geben die Autoren gleichsam Einblick in das geplante Energiewendeprojekt enera.

  15. Was sind eigentlich Daten?

    Directory of Open Access Journals (Sweden)

    Jakob Voß

    2013-10-01

    Full Text Available Daten und ihre Nutzung als Linked Data, Big Data, Forschungsdaten, etc. erfahren aktuell verstärkte Aufmerksamkeit. Bei genauerer Betrachtung lässt sich dieses Interesse bis zu den Anfängen der Computernutzung zurückverfolgen, jedoch ohne dass ein eigenständiges, theoretisches Konzept von ‘Daten’ erkennbar wäre. Der folgende Beitrag gibt eine kurze Einführung in verschiedene Datenbegriffe aus philosophischer Sicht und verbindet diese mit dem Konzept des Dokuments in der Bibliotheks- und Informationswissenschaft.

  16. Optimized retrofitting in order to mobilize CO{sub 2} reduction potentials in existing residential buildings; Umfassende Mobilisierung von CO{sub 2}-Reduktionspotentialen im Wohngebaeudebestand durch optimierte Altbausanierung

    Energy Technology Data Exchange (ETDEWEB)

    Goerg, M. [Stadtwerke Hannover AG (Germany)

    1995-03-01

    The article describes the exploitation of CO{sub 2} reduction potentials as of problem of social innovation. The possibilities and limits of new services such as heat service and conservation contracting are gone into. The necessity of investment support is explained and a financing concept is presented. (orig.) [Deutsch] Der Beitrag beschreibt die Erschliessung der CO{sub 2}-Reduktionspotentiale als ein Problem gesellschaftlicher Innovation. Dargestellt werden Moeglichkeiten und Grenzen neuer Dienstleistungsangebote wie Waermeservice und Einspar-Contracting. Die Notwendigkeit einer Investitionsfoerderung wird begruendet und eine Finanzierungsidee vorgestellt. (orig.)

  17. Logfile-Analysen: Möglichkeiten und Grenzen ihrer Nutzung bei Untersuchungen zur Mensch-Maschine-Interaktion

    Directory of Open Access Journals (Sweden)

    Burkhard Priemer

    2004-06-01

    Full Text Available Die Aufzeichnung der Computernutzung in automatisch generierten elektronischen Protokollen – so genannten Logfiles – entwickelt sich zu einer zunehmend genutzten Erfassungsmethode bei Untersuchungen der Interaktion zwischen Mensch und Computer. Dieser Beitrag bietet einen einführenden Überblick über Verfahren der Logfile-Aufzeichnung und der Analyse der Daten. Neben einer Erläuterung der Begrifflichkeiten werden sowohl Vor- und Nachteile von Logfile-Auswertungen als auch grundlegende Methoden, mathematische Beschreibungen des Nutzerverhaltens und Ansätze der Typisierung von Nutzeraktivitäten dargestellt.

  18. Rezension zu: Antke Engel: Bilder von Sexualität und Ökonomie. Queere kulturelle Politiken im Neoliberalismus. Bielefeld: transcript Verlag 2009.

    Directory of Open Access Journals (Sweden)

    Kateřina Kolářová

    2009-10-01

    Full Text Available Geschlechtliche und sexuelle Differenz/en werden gegenwärtig häufig nicht mehr als Problem verstanden, sondern zunehmend als kulturelles Kapital zelebriert. Diese Form der Wertschätzung von Diversität in der Spätmoderne, so Antke Engel, ist eng mit neoliberalen Entwürfen von Subjektivität verwoben. Sie bietet „projektive Integration“ – ein Begriff, der die affektive Besetzung von Bildern beschreibt – als Analysewerkzeug an und fragt anhand differenzierter Bildlektüren nach queeren und neoliberalen Topoi und Diskursen, die in diesen Bildern miteinander verwoben werden. Sie macht so Widersprüche sichtbar, die sowohl der neoliberalen Marktlogik als auch dem queeren Projekt inhärent sind, und führt vor, wie sich unter diesen Bedingungen der Unentscheidbarkeit queere Politik denken ließe. Mit diesem Band formuliert Engel einen wichtigen Beitrag zur kritischen Reflexion von sowohl Neoliberalismus als auch queerer Politik.

  19. Über diese Ausgabe

    Directory of Open Access Journals (Sweden)

    Editors / Herausgeber

    2015-06-01

    Full Text Available Erzählungen können absichtlich die Unwahrheit verbreiten. Ob der Autor bzw. die Autorin selbst der Lüge bezichtigt werden kann oder sollte, hängt allerdings nicht nur davon ab, wie man Lüge definiert, sondern auch davon, welchen Status man der Erzählung zuschreibt: Worin unterscheidet sich der Wahrheitsanspruch fiktionaler Äußerungen in literarischen Texten von dem faktualen Erzählens? Kann Fiktion lügen? Eva-Maria Konrad plädiert nach einer Auseinandersetzung mit Genettes Studie zu Paratexten dafür, vom Autor verantwortete Vorworte in literarischen Texten nicht generell als fiktionale Äußerungen zu betrachten – unter bestimmten Voraussetzungen, so Konrad, könnten daher auch Herausgeberfiktionen als Lügen bezeichnet werden. Jochen Mecke hingegen argumentiert, dass fiktionale Literatur nie lügen kann, da jede Zuschreibung von Aufrichtigkeit an literarische Texte auf jenem Pakt zwischen Leser(in und Autor(in basiert, den Samuel Taylor Coleridge als „willing suspension of disbelief“ bezeichnet hat. Entscheidend ist dabei, so Mecke, nicht die Fiktivität der erzählten Ereignisse, sondern die Fiktionalität der Aussageinstanz. Sabine Schlickers untersucht in ihrem Beitrag zum unzuverlässigen und verstörenden Erzählen im argentinischen Kino, wie Ambiguität entsteht – der zeitgenössische Film macht es dem Publikum häufig schwer, dem impliziten Autor eine eindeutige Intention, sei es Ironie, Spiel oder Lüge, zuzuschreiben. Im vierten Beitrag des Themenhefts widmet sich Tanja Serisier der Problematik der Glaubwürdigkeit in Vergewaltigungsnarrativen und diskutiert die Differenzen zwischen juristischen Wahrheitsbegriffen auf der einen und dem subjektiven Wahrheitsempfinden auf der anderen Seite. Mit Ansgar Nünning konnte diesmal für die Rubrik „My Narratology“ ein Interviewpartner gewonnen werden, dessen Arbeiten zur historischen, kontextorientierten und kulturwissenschaftlichen Narratologie einen ma

  20. Der Einsatz von E-Portfolios in der Berufsausbildung - Konzeption und Potenziale

    Directory of Open Access Journals (Sweden)

    Uwe Elsholz

    2010-02-01

    Full Text Available In der beruflichen Bildung sind (E-Portfolios zur Reflexion des Gelernten – anders als etwa an Hochschulen oder in allgemeinbildenden Schulen – in Theorie und Praxis gegenwärtig kaum existent. Konzepte und Studien zum Einsatz von E-Portfolios in der Berufsausbildung und der Weiterbildung fehlen weitgehend, so dass die Potenziale von Portfolioarbeit für eine selbstbewusstere und selbstbestimmtere Gestaltung beruflichen Lernens bisher ungenutzt bleiben. Hier setzt dieser Beitrag an. Es wird ein Konzept vorgestellt, wie der Einsatz eines E-Portfolios die Berufsausbildung im dualen System unterstützen kann. Anhand des dargestellten Beispiels werden Möglichkeiten und Grenzen des Einsatzes von E-Portfolios in der beruflichen Bildung aufgezeigt. Die Umsetzung des E-Portfolios findet im Rahmen des berufswissenschaftlich begründeten E- Learning-Konzepts der Kompetenzwerkst@tt statt (vgl. Howe/Knutzen 2007. Die Kompetenzwerkst@tt ist ein softwaregestütztes Ausbildungskonzept, das sich an realen beruflichen Arbeitsprozessen und Ansätzen des Situierten Lernens orientiert. Im Mittelpunkt des E-Portfolios als Teil der Kompetenzwerkst@tt steht die lernortübergreifende Dokumentation und Reflexion der Ausbildungsinhalte der Dualen Berufsausbildung. Im Beitrag wird gezeigt, wie die konzeptionellen Überlegungen zur Portfolioarbeit in der beruflichen Bildung vom Portfolio-Diskurs in anderen Bildungsbereichen beeinflusst sind, sich aber in der Umsetzung und in den konkreten Zielsetzungen deutlich unterscheiden. Es werden darüber hinaus weitere Möglichkeiten und Optionen von Portfolioarbeit in der beruflichen Bildung aufgezeigt.

  1. Under Familiar Fire: Making Decisions During the “Kivu Crisis” 2008 in Goma, DR Congo Unter vertrautem Feuer: Entscheidungsfindung während der “Kivu-Krise” in Goma, DR Kongo, 2008

    Directory of Open Access Journals (Sweden)

    Silke Oldenburg

    2010-01-01

    Full Text Available This paper explores the decision-making processes used by the inhabitants of Goma during the Kivu Crisis in October 2008. The paper’s aim is twofold: After providing a short history of the October 2008 events, it seeks in the empirical part to distinguish and clarify the role of rumours and narratives in the setting of violent conflict as well as to analyse their impact on decision-making processes. As the epistemological interest lies more on the people who stay rather than those who flee, in the second part the paper argues that the practice of routinization indicates a conscious tactic whose purpose is to counter the non-declared state of exception in Goma. Routinization is defined as a means of establishing order in everyday life by referring to narratives based on lived experiences. Die Autorin des Beitrags untersucht Entscheidungsfindungsprozesse der Einwohner von Goma während der Kivu-Krise im Oktober 2008. Nach einer kurzen Geschichte der Ereignisse wird im empirischen Teil des Beitrags die Rolle von Gerüchten und Erzählungen für die gesellschaftliche Szenerie gewaltsamer Konflikte aufgezeigt und voneinander abgegrenzt und ihre jeweilige Bedeutung für Entscheidungsfindungsprozesse analysiert. Da sich das Forschungsinteresse der Autorin in erster Linie auf den Teil der Bevölkerung richtet, der am Ort des Geschehens bleibt, und weniger auf den, der sich zur Flucht entscheidet, wird im zweiten Teil des Beitrags die Praxis der Routinisierung hervorgehoben, eine bewusste Strategie der Betroffenen, um mit dem nicht-deklarierten Ausnahmezustand in Goma umzugehen. Routinisierung wird als Mittel definiert, die alltägliche Ordnung aufrechtzuerhalten, indem man auf Erzählungen gelebter Erfahrung zurückgreift.

  2. Das verfügbare Geld im Jugendalltag von 13- bis 17-jährigen Schülern und Schülerinnen: empirische Ergebnisse

    OpenAIRE

    Tully, Claus; Santen, Eric van

    2012-01-01

    "Prozesse der Bildung, Ablösung, Differenzierung und Positionierung gehören zur Verselbstständigung und zum Erwachsenwerden. Die Verfügung über Geld spielt dabei eine wichtige Rolle. Geld, als Voraussetzung für Konsum und damit Mittel, um 'im Spiel zu bleiben'. SchülerInnen verfügen über keine eigenen Einkünfte und sind auf Zuwendungen (Taschengeld und staatliche Transferleistungen wie Schüler-Bafög) oder selbst hinzu verdientes Geld angewiesen. Der Beitrag stellt empirische Ergebnisse zur Hö...

  3. Preventing damage in heating systems. Corrosion resulting from water in heating systems; Schaeden in Heizungsanlagen vermeiden. Korrosion in Verbindung mit Heizungswasser

    Energy Technology Data Exchange (ETDEWEB)

    Hannemann, M. [Hannemann Wassertechnik Deutschland, Erding (Germany)

    2004-02-01

    Nearly all heating systems today use water as heating fluid. It is therefore important to know about the properties of this heat carrier fluid and about its interactions with heating system materials. This contribution discusses the main characteristics of common types of water and their effects on the heating systems. (orig.) [German] Praktisch in jeder Heizungsanlage wird Wasser als Waermetraeger verwendet. Von daher ist es ratsam, Eigenschaften dieses Waermetraegers und seine Wechselwirkungen mit Heizungswerkstoffen zu kennen. Der nachfolgende Beitrag behandelt die wichtigsten Eigenschaften gebraeuchlicher Waesser und deren Auswirkungen auf die Heizungsanlagen. (orig.)

  4. Al-Qurû’ fi Al-Qur’an ‘Inda Al-Anbary fi Al-Adhdâd

    Directory of Open Access Journals (Sweden)

    Raushani Azza

    2018-03-01

    Full Text Available This study examines about the term al-Qurû in the Qur’an. Al-Qurû is one of the most popular discussions among muslim scholars and mufasir, both in terms of language and fiqh. However, there is a bate among muslim scholar and mufasir about the meaning of al-Qurû. It’s because al-Qurû is one of the sentence of al-Adhdâd wich has two meaning, especially in the Qur’an, namely haid (menstruation and thahr. One of the most popular muslim scholar who concern in Qur’an and Arabic is al-Anbari with his book al-Adhdâd. Al-Anbari explains that Qurû has two meanings, First, al-Qurû in etymology is the form of Jama’ from aqra and qurû. Second, al-Qurû has a meaning of menstruation, thahr, or the period of iddah as a sign of being allowed to remarry after certain period of time.

  5. E-Learning als Möglichkeit zur Unterstützung des selbstgesteuerten Lernens an Berufsschulen

    Directory of Open Access Journals (Sweden)

    Silvia Dreer

    2008-06-01

    Full Text Available Im Mittelpunkt dieses Beitrages steht die Frage, wie durch die Potenziale von ELearning selbstgesteuertes Lernen an berufsbildenden Schulen (Berufsschulen unterstützt werden kann und wie diese neuen Lernangebote im Unterricht effektiv genutzt werden können. Dann werden bereits vorhandene empirische Belege zum selbstgesteuerten Lernen aufgearbeitet und unterschiedliche Möglichkeiten zur Förderung des selbstgesteuerten Lernens betrachtet bzw. welche Lernumgebungen notwendig sind, um selbstgesteuertes Lernen zu ermöglichen. Es wird auf die Besonderheiten von E-Learning eingegangen und eine mediendidaktische Konzeption realisiert. Im Rahmen der empirischen Untersuchung wird untersucht, ob selbstgesteuertes Lernen durch E-Learning unterstützt werden kann. Den Abschluss bildet eine Abschätzung des mediendidaktischen Potenzials von Lernumgebungen die selbstgesteuertes Lernen unterstützen in Hinblick auf den Unterricht in berufsbildenden Schulen.

  6. Al-Âyah al-Mutasyâbihât al-Lafzhiyyah fi Sûrah al-An’âm ‘Inda al-Kirmâny

    Directory of Open Access Journals (Sweden)

    Hikmatiar Pasya

    2017-07-01

    Full Text Available This paper discusses about the verses of mutasyâbihât in the Quran. The debate of this verses caused various opinions. The meaning of the mutasyâbihât in this paper is the similarity and difference of the words in the Qur'an. Mufasir have different opinion about the meaning of the verse of mutasyâbihât al-lafdzi. In addition, many Hufadz of the Quran who are confused from one verse to another, or one chapter to another. It’s because similarity of verses in the Qur'an with other verses. So the writer wants to explain the verses mutasyâbihât al-lafdzi in the perspective of Hamzh al-Karmani in Surah al-An'âm. In this discussion the author discovers some passages in mutasyâbihât al-lafdzi, namely Asrâru al-balaghah fi mutasyabih al-lafdzi, Asrar al-balaghah fi mutasyabih al-hurf, and murâ'ah al-ikhtilâfmurâd bi al-lafdzi al-mukarrar.

  7. Diffusion-induced quadrupole relaxation of 27Al nuclei in dilute Al-Ti, Al-Cr, Al-Mn, and Al-Cu alloys at high temperatures

    International Nuclear Information System (INIS)

    Bottyan, L.; Beke, D.L.; Tompa, K.

    1983-01-01

    The temperature dependence of the laboratory frame spin-lattice relaxation time of 27 Al nuclei is measured in 5N Al and in dilute Al-Ti, Al-Cr, Al-Mn, and Al-Cu alloys at 5.7 and 9.7 MHz resonance frequencies. The relaxation in pure aluminium is found to be purely due to the conduction electrons. An excess T 1 -relaxation contribution is detected in all Al-3d alloys investigated above 670 K. The excess relaxation rate is proportional to the impurity content and the temperature dependence of the excess contribution is of Arrhenius-type with an activation energy of (1.3 +- 0.3) eV for all of the investigated alloys. The relaxation contribution is found to be quadrupolar in origin and is caused by the relative diffusional jumps of solute atoms and Al atoms relatively far from the impurity. (author)

  8. Interfacial phenomena in the reactions of Al-B, Al-Ti-B, and Al-Zr-B alloys with KF-AlF3 and NaF-AlF3 melts

    International Nuclear Information System (INIS)

    Lee, M.S.; Terry, B.S.; Grieveson, P.

    1993-01-01

    The interfacial phenomena occurring during the contacting of liquid Al-B, Al-Ti-B, and Al-Zr-B melts with KF-AlF 3 liquid fluxes have been investigated by optical examination of quenched metal drops previously immersed in the liquid fluxes. Reactions in the Al-B/KF-AlF 3 system involve the formation of metastable AlB 12 at the metal/flux interface. At high KBF 4 levels in the flux, the AlB 12 is dispersed in the flux and also at low KBF 4 levels in the metal. Reactions in the Al-Ti-B/KF-AlF 3 system involve the formation of TiB 2 , which may be dispersed in either the metal or the flux depending upon the composition of the flux. The results obtained for the Al-Ti-B/NaF-AlF 3 and Al-Zr-B/KF-AlF 3 systems were similar to those observed for the Al-Ti-B/KF-AlF 3 system

  9. Fachsprachlichkeit und Verständlichkeit in deutschen Verträgen

    DEFF Research Database (Denmark)

    Larsen, Aase Voldgaard

    2010-01-01

    In diesem Beitrag wird die Fachsprachlichkeit und Verständlichkeit in deutschen Verträgen thematisiert. Der Beitrag basiert auf einer Untersuchung, die im Rahmen meiner Dissertation durchgeführt wurde. Sie trägt den Titel „Faglighed og forståelighed i kontrakter. En undersøgelse af sproglige fors...

  10. Synthesizing (ZrAl3 + AlN)/Mg-Al composites by a 'matrix exchange' method

    Science.gov (United States)

    Gao, Tong; Li, Zengqiang; Hu, Kaiqi; Han, Mengxia; Liu, Xiangfa

    2018-06-01

    A method named 'matrix exchange' to synthesize ZrAl3 and AlN reinforced Mg-Al composite was developed in this paper. By inserting Al-10ZrN master alloy into Mg matrix and reheating the cooled ingot to 550 °C, Al and Mg atoms diffuse to the opposite side. As a result, liquid melt occurs once the interface areas reach to proper compositions. Then dissolved Al atoms react with ZrN, leading to the in-situ formation of ZrAl3 and AlN particles, while the Al matrix is finally replaced by Mg. This study provides a new insight for preparing Mg composites.

  11. Thermal disposal of sewage sludge: Status and trends; Stand und Entwicklung der thermischen Klaerschlammentsorgung

    Energy Technology Data Exchange (ETDEWEB)

    Johnke, B. [Umweltbundesamt, Berlin (Germany); Wiebusch, B. [Hannover Univ. (Germany). Inst. fuer Siedlungswasserwirtschaft und Abfalltechnik

    1997-04-01

    In West Germany, 2.5 - 2.75 million t/a of dehydrated sewage sludge from municipal sewage systems must be managed every year. About 30% of this volume is used in agriculture, 14% is combusted,and 56% is dumped. Medium-term forecasts envisage a further increase of the sewage sludge volume to about 3 million t/a for East Germany and West Germany together. According to the specifications of the TA Siedlungsabfall (Technical Guide for Management of Domestic Waste), dumping of untreated sewage sludge will be prohibited from 2005 at the latest. (orig.) [Deutsch] In den alten Bundeslaendern sind derzeit 2,5-2,75 Mio. t/a Klaerschlammtrockensubstanz (TS) aus der kommunalen Abwasserreinigung zu entsorgen, von denen z.Zt. ca. 30% landwirtschaftlich verwertet, ca. 14% verbrannt und 56% auf Deponien abgelagert werden. Die mittelfristigen Erwartungen gehen von einem weiteren Anstieg der Klaerschlamm-Mengen aus, so dass in den alten und neuen Bundeslaendern mit mehr als 3 Mio. t/a Klaerschlammtrockensubstanz (TS) zu rechnen ist, die einer Entsorgung zugefuehrt werden muessen (Quelle: H. Kaiser Unternehmensberatung Tuebingen 1996). Aufgrund der Anforderungen der TA Siedlungsabfall wird spaetestens ab dem Jahr 2005 eine direkte Ablagerung von unbehandelten Klaerschlaemmen auf Deponien wegen des zu hohen organischen Anteils nicht mehr zulaessig sein. (orig.)

  12. Coupled growth of Al-Al2Cu eutectics in Al-Cu-Ag alloys

    International Nuclear Information System (INIS)

    Hecht, U; Witusiewicz, V; Drevermann, A

    2012-01-01

    Coupled eutectic growth of Al and Al 2 Cu was investigated in univariant Al-Cu-Ag alloys during solidification with planar and cellular morphology. Experiments reveal the dynamic selection of small spacings, below the minimum undercooling spacing and show that distinct morphological features pertain to nearly isotropic or anisotropic Al-Al 2 Cu interfaces.

  13. AL ITTIJAHAT AL MUNHARIFAH FI AT TAFSIR LI BADLI ASHAB AL MADZAHIB AL NAHWIYYAH WA BADL MAN YAJHALUNA QAWAID AL LUGHAH AL ARABIYYAH FI NADHAR MUHAMMAD HUSAIN AL DZAHABIY

    Directory of Open Access Journals (Sweden)

    Misbakhudin Misbakhudin

    2017-06-01

    Full Text Available One of the most precious achievement in qur’anic studies was the book of Al-Ittijâhât al-Munharifah fî al-Tafsîr: Dawâfi’uha wa Daf’uha written by A great Islamic scholar, Muhammad Husein al-Dzahabî. He was succeeded in discussing several issues of corruptions of the exegesis of the holy Qur’an. This article is aimed to explain and to describe his analysis toward several corrupted linguist interpretations in their originations and such corrupted linguistic interpretations of the holy Qur’an which are ignoring Arabic structures and grammers

  14. Biologisch-dynamische Forschung zwischen "wissenschaftlicher Weltsicht" und "Ideologie"

    OpenAIRE

    Eysel, Georg

    2002-01-01

    Der Beitrag zeigt den Konflikt zwischen "wertefreier" Wissenschaft und "ganzheitlicher" Forschung auf. Ein Zusammenspiel bio-dynamischer Forschung und der Anthroposophie mit anderen Disziplinen könnte einen Beitrag zu einem neuen Wissenschaftsbegriff mit umfassender Weltanschauung leisten. Dialog, Verständnis, Toleranz, Offenheit, kritisches Hinterfragen und Mut zur sinnvollen Anpassung sind dafür notwendige Schritte.

  15. Interdisciplinary analysis of the chances of implementation of an energy conservation and air pollution abatement policy. Adverse and favourable conditions for rational energy use in private households and their responsible decision-makers from an economic and social psychological perspective; Interdisziplinaere Analyse der Umsetzungschancen einer Energiespar- und Klimaschutzpolitik. Hemmende und foerdernde Bedingungen der rationellen Energienutzung fuer private Haushalte und ihr Akteursumfeld aus oekonomischer und sozialpsychologischer Perspektive

    Energy Technology Data Exchange (ETDEWEB)

    Hennicke, P.; Jochem, E.; Prose, F.

    1997-08-01

    The investigation attempted an analysis of the causes and remedies of the gap between ecological and climate-relevant requirements on the one hand and public and political action on the other hand. It presents a theoretical concept for an ecologically oriented social restructuring process which will support rational energy use and the appropriate research and development measures more strongly than it does now. While the Federal government intends a 25 % reduction of carbon dioxide emissions by 2005, an 80 % reduction is required on a long-term basis (e.g. by 2050). In view of this, the contribution of the German government is interpreted as a necessary but still insufficient contribution to sustainability. [German] Diese Studie erarbeitet einen Beitrag zur Analyse der Ursachen und Loesungsmoeglichkeiten fuer den Widerspruch zwischen umwelt- und klimarelevanten Handlungsnotwendigkeiten einerseits und den gesellschaftlichen Handlungsdefiziten andererseits. Weitergehend erbringt sie einen theoretisch-konzeptionellen Ansatz zum oekologischen Umbau der Industriegesellschaft. Dadurch wird konkret dazu beigetragen, die Politik zur rationellen Energieanwendung einschliesslich der Forschungs- und Entwicklungspolitik besser als bisher zu unterstuetzen. Ausgegangen wird von dem energie- und klimapolitischen Ziel der Bundesregierung, bis zum Jahr 2005 die CO{sub 2}-Emissionen gegenueber dem Referenzjahr 1990 um 25% zu reduzieren. Langfristig, bis etwa zum Jahr 2050, ist nach der Empfehlung der Klima-Enquete-Kommission eine CO{sub 2}-Reduktion um 80% erforderlich. Dieser Beitrag der Bundesrepublik zum internationalen Klimaschutz kann als notwendige, wenn auch noch nicht hinreichende Voraussetzung fuer eine 'zukunftsfaehige Entwicklung' (sustainability) in der Bundesrepublik interpretiert werden. (orig.)

  16. Wenn Edusphäre und Blogosphäre sich treffen. Weblogs an Hochschulen zwischen Zitationskartell und Diskursrevolte

    Directory of Open Access Journals (Sweden)

    Stefanie Panke

    2012-03-01

    Full Text Available Der vorliegende Beitrag widmet sich dem Thema «Edublogging», also der Nutzung von Weblogs im Bildungsbereich, und fokussiert dabei auf den Hochschulsektor. Weblogs werden vielerorts als Instrument für die Lehre, aber auch als ­Diskussionsplattform im E-Learning-Forschungsdiskurs sowie als Mittel zur Öffentlichkeitsarbeit in E-Learning-Zentren und anderen Zentraleinrichtungen eingesetzt. Hinzu kommen Blogfarmen bzw. Multiblogs, die jedem und jeder Hochschulangehörigen mit wenigen Klicks die Einrichtung einer Weblog-Präsenz eröffnen. Entsprechend facettenreich präsentiert sich die Landschaft der Edublogs. Der Artikel beleuchtet das Phänomen «Edublogosphäre» durch eine umfangreiche Literatursichtung, Web-Recherchen, Inhaltsanalysen und Befragungen. Angestrebt wird eine Kartografie der vielfältigen Landschaft an Edublogs. Im Ergebnis werden Besonderheiten der Weblog-Strategien von E-Learning-Einrichtungen, bloggenden E-Learning-Wissenschaftlern/-innen, Blogfarmen und weiteren Einsatzformen in Hochschulbereich beschrieben.

  17. Messung computer- und informationsbezogener Kompetenzen von Schülerinnen und Schülern als Schlüsselkompetenz im 21. Jahrhundert

    Directory of Open Access Journals (Sweden)

    Birgit Eickelmann

    2011-12-01

    Full Text Available Mit der ICILS 2013 (International Computer and Information Literacy Study realisiert die IEA (International Association for the Evaluation of Educational Achievement erstmalig eine internationale Vergleichsstudie, die empirisch abgesichert Schülerkompetenzen im Bereich der computer- und informationsbezogenen Kompetenzen (Computer and Information Literacy, kurz: CIL erhebt. Mit dieser Studie werden informations- und computerbezogene Kompetenzen, die im 'deutschen' Sprachgebrauch auch oft unter dem affinen Begriff ICT-Literacy geführt werden, als Large-Scale-Assessments erfasst. Im folgenden Beitrag soll die Relevanz der Messung dieser Schlüsselkompetenz aufgezeigt werden. Alsdann werden das der Studie zugrundeliegende Messkonstrukt und seine definitorischen Bereiche beschrieben. Die hier vorgestellte Definition des CIL-Konstruktes bildet die Grundlage für die datengestützte Entwicklung von Kompetenzstufen, die aus der Hauptstudie von ICILS im Jahr 2013 hervorgehen werden. The IEA (International Association for the Evaluation of Educational Achievement will realize with ICILS 2013 (International Computer and Information Literacy Study for the first time an international comparative study, which will provide evidence about students' computer- and information-related competencies across countries. As a large-scaleassessment, the study examines the outcome of computer and information literacy. This article outlines the challenges and the relevance of the measurement of this core competence. Additionally the theoretical assessment constructs of CIL (computer and information literacy and their definitional scopes are explained in more detail. The presented definition of CIL is the foundation for a data-based development of proficiency levels within the study, which main survey will take place in 2013.

  18. Aufbau des humanoiden Roboters BART III

    Science.gov (United States)

    Resetov, Dimitri; Pietsch, Björn; Gerth, Wilfried

    Der vorliegende Beitrag präsentiert den humanoiden Roboter BART III, der am Institut für Regelungstechnik als eine robuste und erweiterbare Plattform für weiterführende Grundlagenforschung zur zweibeinigen Fortbewegung entwickelt wurde. Im Gegensatz zu den bisher am IRT genutzten Robotern BARt-UH und LISA besitzt der neue Roboter einen beweglichen Oberkörper mit einem Bauchgelenk und Armen. BART III besitzt insgesamt 19 aktive Freiheitsgrade, 12 davon im Unterkörper. Ein weiteres Merkmal des Roboters ist die im gesamten Körper verteilte Ansteuerelektronik, die neben der lokalen Motorregelung diverse sicherheitsrelevante Funktionen übernimmt.

  19. Konsistente Verknüpfung von Aktivitäts-, Sequenz- und Zustandsdiagrammen

    Science.gov (United States)

    Ebrecht, Lars; Lemmer, Karsten

    Der folgende Beitrag stellt eine formale, generische Verhaltensstruktur und Semantik vor, die die Basis für die konsistente Verknüpfung der drei wichtigsten UML Verhaltensdiagramme bildet. Es wird gezeigt, wie sich das grobe und übersichtliche Verhalten in Aktivitätsdiagrammen, das detaillierte Schnittstellenverhalten in Sequenzdiagrammen und detaillierte Verhaltensmodelle in Zustandsdiagrammen mit Hilfe der Semantik konsistent miteinander verknüpfen lassen und die Inhalte der drei genannten Verhaltensdiagramme eindeutig miteinander in Beziehung gebracht werden können. Als Anwendungsbeispiel wird die komplexe, sicherheits- und echtzeitkritische zugseitige Komponente des Europäischen Leit- und Sicherungstechnik Systems (ETCS) verwendet.

  20. Informatische Pädagogik - pädagogische Informatik. Beispiele für fächerverbindende Projekte mit medienerzieherischem Anspruch

    Directory of Open Access Journals (Sweden)

    Michael Weigend

    2001-12-01

    Full Text Available Mit der Profilbildung der Schulen und mit der Entwicklung individueller schulinterner Lehrpläne, sind in zunehmendem Masse Kopplung von Oberstufenkursen und fächerverbindenes Unterrichten gefragt. In diesem Beitrag werden Projekte vorgestellt, die eine Kooperation der Fächer Informatik und Erziehungswissenschaft voraussetzen. Inhaltlich stellen die Neuen Medien den Bezugspunkt dar: multimediale und zum Teil interaktive Anwendungen, wie digitale Animationen, Spiele und Bildschirm-Experimente können von den Schüler/innen selbst entwickelt und als Medien eingesetzt werden, wobei technische und gesellschaftliche Fragen der Mediengestaltung und der Mediennutzung zu reflektieren sind.

  1. Graded thermal insulation layer systems; Gradierte Waermedaemmschichtsysteme

    Energy Technology Data Exchange (ETDEWEB)

    Leushake, U.; Krell, T. [Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Koeln (Germany). Inst. fuer Werkstoff-Forschung

    1996-12-31

    Graded thermal insulation systems reduce local stresses between two layers. Grading usually involves a concentration variation in a second phase but may also involve variations of the microstructure or chemical composition. The contribution discusses the application of this technique for thermal protection of turbine blades in aircraft propulsion systems. [Deutsch] Mit Hilfe gradierter Waermeschichtsysteme ist es moeglich die lokalen Spannungen zwischen zwei Schichten zu verringern. Die Gradierung umfasst meistens eine Variation des Gehaltes einer zweiten Phase, kann aber auch die Variation der Mikrostruktur oder der chemischen Zusammensetzung beinhalten. In diesem Beitrag wird auf die Anwendung als thermischer Schutz von Turbinenschaufeln fuer Flugtriebwerke eingegangen.

  2. ähm vs. niinku - Verzögerungssignale in deutschen und finnischen Diskussionen

    Directory of Open Access Journals (Sweden)

    Margarethe Olbertz-Siitonen

    2015-05-01

    Full Text Available Dieser Beitrag beschäftigt sich kontrastiv mit dem Gebrauch von Verzögerungssignalen in deutschen und finnischen Seminardiskussionen. Die voranalytische  Durchsicht der Videomitschnitte zeigte, dass die deutschen Studenten unvergleichlich  häufiger die Verzögerungspartikeln äh und ähm  einsetzten als ihre finnischen Kommilitonen, die in ähnlicher Funktion v.a. die Partikel niinku ('sozusagen' benutzten. Diese  Beobachtung ist insofern von Bedeutung, als es meist die finnischen Gesprächsteilnehmer sind, die in deutsch-finnischen Kontaktsituationen auf eine Fremdsprache (Deutsch  zurückgreifen müssen: Möglicherweise steht finnischen Gesprächspartnern in der Interaktion mit deutschen Muttersprachlern keine deutsche Entsprechung für niinku zur Ver- fügung. Gegebenenfalls resultierende Kommunikationsprobleme sollten dementsprechend nicht vornehmlich interkulturell, sondern interlingual bewertet werden.

  3. Biosorption of heavy metals under anaerobic conditions. Final report; Biosorption von Schwermetallen unter anaeroben Bedingungen. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Kreikenbohm, R.

    1996-12-31

    The precipitation of heavy metals as hydroxides is the standard technique for the decontamination of waste water streams polluted by these elements. On the other side, progress in research has been made concerning the biosorption onto dead biomass and bioprecipitation supported by physiologically active bacteria. As the aim of this study, a flexible strategy has been envisaged cleaning a waste water with definite heavy metal load underlying the process mentioned above. Suitable bacteria were enriched and the process was tested in a technical plant. As result, a very high efficiency of heavy metal elimination has been found. The field of application covered by the acquired process is identical with the whole range of the waste water streams polluted by heavy metals. In addition, a second stage may be necessary if there are any further contaminants to be removed. (orig.) [Deutsch] Bei der Reinigung von schwermetallhaltigen Abwaessern ist der derzeitige Stand der Technik gegeben durch die Neutralisationsfaellung als Hydroxide, waehrend in der Forschung damit begonnen wurde, Biosorption an devitaler Biomasse oder Biopraezipitation durch physiologisch aktive Bakterien zu untersuchen. Ziel des Vorhabens war die Ermittlung einer flexiblen Strategie fuer die Prozessfuehrung zur Abwasserreinigung bei vorgegebener Schadstoffbelastung auf der Basis des zuletzt genannten Prozesses. Dazu wurden geeignete Bakterien angereichert und das Verfahren in einer Technikumsanlage erprobt. Als Ergebnis wurde bei Zufuhr verschiedener Industrieabwaesser eine sehr hohe Effizienz in der Schwermetallelimination gefunden. Das Anwendungsgebiet des erarbeiteten Verfahrens erstreckt sich auf eine Vielzahl schwermetallbelasteter Abwaesser, wobei - je nach Art der weiteren Inhaltsstoffe - eine zusaetzliche Reinigungsstufe vor- oder nachgeschaltet werden muss. (orig.)

  4. Editorial: Qualitative Forschung in der Medienpädagogik

    Directory of Open Access Journals (Sweden)

    Horst Niesyto

    2008-01-01

    Orientierungsmuster herausgearbeitet, die für Jugendliche unterschiedliche Partizipationsmöglichkeiten im Umgang mit Medien eröffnen. Die Analysen verstehen sich als ein Beitrag zur bislang wenig entwickelten medienpädagogischen Professionsforschung. Der Beitrag von Ulrike Wagner und Helga Theunert über «Konvergenzbezogene Medienaneignung in Kindheit und Jugend» stellt das Konzept der konvergenzbezogenen Medienaneignung vor und gibt einen Überblick zu den bisherigen Grundlagenstudien, die das JFF (Institut für Medienpädagogik in Forschung und Praxis im Zeitraum von 2001 bis 2007 durchführte. Der Beitrag konzentriert sich dabei auf die Reflexion von Forschungsperspektiven, die dem vernetzten Medienhandeln von Kindern und Jugendlichen unter inhaltlichen und methodologischen Aspekten gerecht werden. Am Beispiel der dritten Konvergenzstudie werden die methodischen Zugänge bei der Erhebung (Kontaktinterview und Intensivinterview mit Narrationsanreizen, Erfassung von Kontextinformationen sowie bei der Auswertung vorgestellt (Herausarbeitung typischer Muster der konvergenzbezogenen Medienaneignung durch Einzelfallstudien. Als Leitlinien für ihr forschungsmethodisches Vorgehen heben die Autorinnen «Kontextorientierung», «sinnliche und symbolische Dimensionen» sowie «Exemplarität» des Medienhandelns hervor. Mehrere Beiträge gehen auf die Frage ein, welche besonderen Bedingungen mit einer Erforschung des Internets verknüpft sind. Winfried Marotzki betont in seinem Beitrag den kulturellen Charakter des Internets und stellt im Anschluss daran die Charakteristik jener Trends dar, welche mit dem Begriff des Web 2.0 verbunden sind. Methodisch favorisiert er zur Erforschung dieses neuen Raumes diskursanalytische Verfahren in der Tradition wissenssoziologischen Denkens. Diskurse sieht er in diesem Zusammenhang als Artikulation von Erfahrungsräumen innerhalb eines multimodalen Ausdruckskontinuums. Martina Schuegraf stellt in ihrem Beitrag «Das Surfgramm als grafische

  5. Ein digitales Textformat für die Literaturwissenschaft: Die Richtlinien der Text Encoding Initiative und ihr Einsatz bei Textkonstitution und Textanalyse

    Directory of Open Access Journals (Sweden)

    Christof Schöch

    2016-06-01

    Full Text Available Die stetig voranschreitende Digitalisierung literarischer Texte verschiedenster Sprachen, Epochen und Gattungen stellt die Literaturwissenschaften immer wieder vor die Frage, wie sie diese Entwicklung mitgestalten und zu ihrem Vorteil nutzen können. Dabei ist digital nicht gleich digital, sondern es existiert eine Vielzahl sehr unterschiedlicher, digitaler Repräsentationsformen von Text. Nur wenige dieser Repräsentationsformen werden literaturwissenschaftlichen Anforderungen tatsächlich gerecht, darunter diejenige, die den Richtlinien der Text Encoding Initiative folgt. Der vorliegende Beitrag vergleicht zunächst einige derzeit gängige digitale Repräsentationsformen von Text. Für literaturwissenschaftliche Forschung besonders geeignet erweist sich hierbei eine Repräsentationsform, die den Richtlinien der Text Encoding Initiative folgt. Daher informiert der Beitrag anschließend über deren Nutzen für die literaturwissenschaftliche Arbeit, sowohl im Bereich der wissenschaftlichen Textedition als auch im Bereich der Analyse und Interpretation von Texten. Nur wenn die Literaturwissenschaften in ihrer Breite den Nutzen von offenen, expressiven, flexiblen und standardisierten, langfristig nutzbaren Formaten für die Forschung erkennen, können sie sich mit dem erforderlichen Nachdruck für deren Verbreitung einsetzen und durch die zunehmende Verfügbarkeit von Texten in solchen Formaten für die eigene Forschung und Lehre davon profitieren.

  6. Gut gemeint ist nicht gleich gut gemacht! Meant Well is not the Same as Well Done!

    Directory of Open Access Journals (Sweden)

    Sandra Lewalter

    2008-07-01

    Full Text Available Der Beitrag von Manfred Becker lässt sich wohlmeinend als Plädoyer für einen pragmatischen Umgang mit dem AGG lesen. Er möchte Personaler/-innen zeigen, wie die Vorgaben des AGG im Rahmen eines Human Resources Diversity Managements positiv umgesetzt werden können. In weiten Teilen überzeugen die Ausführungen des Autors aber nicht. Gerade die Darstellung der Inhalte des AGG ist stark von seiner skeptischen Grundhaltung gegenüber dessen Zielsetzung geprägt. Auch wenn die Ausführungen zu konkreten Betriebs- und Personalmaßnahmen gelungener sind, stellt dieser Beitrag insgesamt kein überzeugendes und lesenswertes Werk dar.With the best intention, the work by Manfred Becker can be read as a plea for a pragmatic approach to the AGG. He wishes to show personnel how the guidelines of the AGG can be put into practice within the framework of Human Resources Diversity Management. However, the author’s work is often unconvincing. In particular, the presentation of the contents of the AGG is strongly influenced by his skeptical attitude toward its goals. Even when his approach to concrete company and personnel measures is more successful, the book is neither convincing nor a worthwhile read.

  7. Familial ALS

    Science.gov (United States)

    Boylan, Kevin

    2015-01-01

    Synopsis Genes linked to ALS susceptibility are being identified at an increasing rate owing to advances in molecular genetic technology. Genetic mechanisms in ALS pathogenesis appear to exert major effects in ~10% of patients, but genetic factors at some level may be important components of disease risk in most ALS patients. Identification of gene variants associated with ALS has informed concepts of the pathogenesis of ALS, aided the identification of therapeutic targets, facilitated research to develop new ALS biomarkers, and supported the establishment of clinical diagnostic tests for ALS-linked genes. Translation of this knowledge to ALS therapy development is ongoing. PMID:26515623

  8. Malamih al-Ashwat al-'Arabiyyah wa Makharijaha

    Directory of Open Access Journals (Sweden)

    Amrah Muhammad Kasim

    2015-12-01

    Full Text Available This writing discusses on al-ashwat al-‘arabiyyah that is known with “phonetic” term. It talks and interprets makharij al-huruf or place for producing sounds and also processing production of sounds by parts of mouth in Arabic language. The problems of sounds and its systems in Arabic language have been conducted by the scholars of al-ashwat al-‘arabiyyah attractively, neatly, and detail and gotten ahead the phonetic western scholars. Part of their analysis results formulate the study about al-ashwat al-sakinah (al-Shamit is known with vocal and consonant sounds in research questions shawait – shawamit. Ibnu Jinni has formulated “harakat”(wowel in Arabic language and dimension of letter  mad and liyn on alif  letter - waw - ya’ (ا و ي, from these letters create  harakat fathah, dammah, and kasrah. Moreover, in this writing also exist the description of hija’i letters and its makhraj that are correct from parts of mouth and the unity of coordinative sounds that produce sounds in morphemes arrangement, in one word that produces meaning. The result of phonological study has divided al-ashwat to be kinds of sound like the pronounced sounds, produced sounds from mouth, and heard sound.

  9. Transient oxidation of Al-deposited Fe-Cr-Al alloy foil

    International Nuclear Information System (INIS)

    Andoh, A.

    1997-01-01

    The oxide phases formed on an Al-deposited Fe-Cr-Al alloy foil and an Fe-Cr-Al alloy foil of the same levels of Al and (La+Ce) contents, and their oxidation kinetics have been studied in air at 1173 and 1373 K using TGA, XRD and SEM. Al deposition promotes the growth of metastable aluminas (θ-Al 2 O 3 , γ-Al 2 O 3 ). Scales consisting of θ-Al 2 O 3 and a small amount of α-Al 2 O 3 develop on the Al-deposited foil at 1173 K and exhibit the whisker-type morphology. In the early stage of oxidation at 1373 K, thick scales consisting of θ-Al 2 O 3 and α-Al 2 O 3 grow rapidly on the Al-deposited foil. The transformation from θ-Al 2 O 3 to α-Al 2 O 3 is very fast, and the scales result in only α-Al 2 O 3 . In contrast, α-Al 2 O 3 scales containing a minor amount of FeAl 2 O 4 develop on the alloy foil. The growth rate of α-Al 2 O 3 scales on the Al-deposited foil is smaller than that on the alloy foil and very close to that on NiAl at 1373 K. (orig.)

  10. Development trends in municipal sewage treatment - an overview; Entwicklungstendenzen bei der kommunalen Abwasserreinigung - ein Ueberblick

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, M. [Technische Hochschule Darmstadt (Germany). Inst. fuer Wasserversorgung, Abwasserbeseitigung und Raumplanung

    1999-07-01

    gereinigt und die Menge an Zusatzstoffen reduziert werden. Zukuenftig muss beachtet werden, dass Abwasser nach der Reinigung nicht in den Vorfluter abgegeben, sondern wiederverwendet wird. Ueblicherweise wird gereinigtes Abwasser zur Bewaesserung, u.U. auch nach weitestgehender Reinigung und zusaetzlicher Untergrundpassage oder Verschneiden mit Grundwasser als Trinkwasser benutzt. Optimierungsansaetze der verschiedenen Abwasserbehandlungsverfahren muessen vor dieser notwendigen Anforderung gesehen werden. (orig.)

  11. Sprache als Schlüssel zur Welt: Bibliotheken und Sprach-Kitas in guter Partnerschaft

    Directory of Open Access Journals (Sweden)

    Susanne Brandt

    2017-12-01

    Full Text Available Von 2016 bis voraussichtlich 2020 wird durch das Bundesministerium für Familie, Senioren, Frauen und Jugend das Bundesprogramm „Sprach-Kitas. Weil Sprache der Schlüssel zur Welt ist“ gefördert. Es richtet sich an Kindertageseinrichtungen, die von einem überdurchschnittlich hohen Anteil von Kindern mit besonderem Bedarf an sprachlicher Bildung und Förderung besucht werden. Dabei stehen besonders die folgenden drei Zielbereiche im Fokus: alltagsintegrierte sprachliche Bildung, inklusive Bildung und Zusammenarbeit mit den Familien. An den Standorten dieser mehr als 3000 Sprach-Kitas in Deutschland gibt es nahezu überall öffentliche Bibliotheken, die als nachbarschaftliche Partnerinnen den Sprach-Kitas bei der Sprachförderung mit vielfältigen Medien und Kooperationsangeboten zur Seite stehen. Auch als Schnittstelle zwischen Kita und Familie können die Büchereien wichtige Aufgaben im Rahmen des Programms übernehmen. Die Büchereizentrale Schleswig-Holstein hat daher mit Fördermitteln des Landes und in guter Abstimmung mit den Sprachkoordinatorinnen der Kitas das Projekt „Mit Worten wachsen“ entwickelt. Der Beitrag beschreibt, welche Chancen und Herausforderungen sich durch eine solche Zusammenarbeit mit Sprach-Kitas für Bibliotheken ergeben und wie sich daraus eine lebendige interdisziplinäre Partnerschaft im Sinne der genannten Zielbereiche entwickeln lässt. Since 2016, the Federal Ministry for Family Affairs, Senior Citizens, Women and Youth has sponsored the programme “Language day-care centres. Because language is the key to the world” (Sprach-Kitas. Weil Sprache der Schlüssel zur Welt ist; this is expected to last until 2020. The programme addresses day-care facilities which are attended by an above-average number of children with special needs in their language development. The following three aims are at the centre of the programme: language education which is integrated in everyday life; education based on

  12. Proton irradiation studies on Al and Al5083 alloy

    Science.gov (United States)

    Bhattacharyya, P.; Gayathri, N.; Bhattacharya, M.; Gupta, A. Dutta; Sarkar, Apu; Dhar, S.; Mitra, M. K.; Mukherjee, P.

    2017-10-01

    The change in the microstructural parameters and microhardness values in 6.5 MeV proton irradiated pure Al and Al5083 alloy samples have been evaluated using different model based techniques of X-ray diffraction Line Profile Analysis (XRD) and microindendation techniques. The detailed line profile analysis of the XRD data showed that the domain size increases and saturates with irradiation dose both in the case of Al and Al5083 alloy. The corresponding microstrain values did not show any change with irradiation dose in the case of the pure Al but showed an increase at higher irradiation doses in the case of Al5083 alloy. The microindendation results showed that unirradiated Al5083 alloy has higher hardness value compared to that of unirradiated pure Al. The hardness increased marginally with irradiation dose in the case of Al5083, whereas for pure Al, there was no significant change with dose.

  13. KS R41B. A high performance steel-aluminium composite material; KS R41B. Ein Stahl-Aluminium-Verbundwerkstoff fuer hohe Belastungen

    Energy Technology Data Exchange (ETDEWEB)

    Deicke, K. [KS Gleitlager GmbH (Germany). Bereich Metall; Matucha, H.; Schubert, W. [KS Gleitlager GmbH, St. Leon-Rot (Germany); Steffens, T. [KS Gleitlager GmbH, Neckarsulm (Germany)

    2002-08-01

    Aluminium-tin alloys have been well-known for a long time and have proved to be suitable bearing materials for crankshaft bearings for many years. The known alloy AlZn4,5SiCuPb is one of the aluminium materials capable of sustaining the highest mechanical loads. In order to achieve optimum sliding properties, it would be necessary to increase the share of the soft lead phase in the alloy. This article by KS Gleitlager GmbH shows a reasonably priced manufacturing technology for high-performance aluminium-zinc-silicon-copper alloys. (orig.) [German] Die Aluminium-Zinn-Lagerlegierungen sind seit langem bekannt und haben sich seit Jahren als Lagerwerkstoff fuer Kurbelwellenlager bewaehrt. Die Legierung AlZn4,5SiCuPb gehoert zu den mechanisch am hoechsten belastbaren Aluminium-Werkstoffen. Um optimale Gleiteigenschaften zu erzielen, muesste in der Legierung der Anteil des weichen Bleis noch weiter erhoeht werden. Dieser Beitrag der KS Gleitlager GmbH zeigt eine kostenguenstige Herstelltechnologie fuer hochbelastbare Aluminium-Zink-Silizium-Kupfer-Legierungen. (orig.)

  14. Der Zusammenhang von Partnermarktopportunitäten aus dem Freundeskreis und der Stabilität von Paarbeziehungen : Eine Analyse mit den Daten des Partnermarktsurvey

    OpenAIRE

    Häring, Armando

    2014-01-01

    "Der Beitrag analysiert den Zusammenhang zwischen Partnermarktoportunitäten aus dem Freundeskreis und der Stabilität von Paarbeziehungen. Unter Verwendung des theoretischen Konzepts der Theorie der Interaktionsgelegenheiten sowie von Annahmen der Austauschtheorie und der Familienökonomie, werden mögliche Zusammenhänge zwischen gemeinsamen Freundeskreisen mit dem Partner, Partnermarktgelegenheiten aus dem Freundeskreis (sex ratio) und der Stabilität von Paarbeziehungen diskutiert. Der Beitrag ...

  15. PEMBARUAN MASLAḤAH DALAM MAQĀṢID AL- SHARĪ‘AH: TELAAH HUMANISTIS TENTANG AL-KULLIYYĀT AL-KHAMSAH

    Directory of Open Access Journals (Sweden)

    Zaenuddin Mansyur

    2012-06-01

    Full Text Available Abstract:   In order to answer a variety of issues faced by human being in the current era, such as human rights abuses, social disintegration, and terrorism, the renewal of Islamic law in the level of theoretical and practical aspects is very urgent. This paper aims to examine one of the Islamic legal reform efforts, namely to build a more technical understanding of the concept of maṣlaḥah contained in the maqāṣīd sharī‘ah, called the al-kulliyat al-khamsah. Therefore, the concept of maṣlaḥah in ḥifẓ al-dīn is technically defined as al-ḥurriyah al-i‘tiqād (freedom of religion and schools; in ḥifẓ al-nafs as al-karamat al-insān (human being breeding; in ḥifẓ al-nasl as ḥifẓ al-usrah (wholeness and harmony of the family; in ḥifẓ al-māl as al-taḍammun al-insān (social solidarity , and in ḥifẓ al-‘aql as al-ḥuqūq as al-tarbiyāt (increasing human resources quality.Abstrak: Demi menjawab aneka persoalan zaman yang dihadapi manusia era sekarang, seperti penyelewengan terhadap HAM, disintegrasi sosial, dan terorisme, maka pembaharuan hukum Islam dalam tataran teoretis dan praktis urgen dilakukan. Tulisan ini bertujuan untuk mengkaji salah satu upaya pembaruan hukum Islam, yaitu membangun pemahaman yang lebih teknis terhadap konsep maṣlaḥah yang terkandung dalam maqāṣīd sharī‘ah, yang disebut dengan al-kulliyāt al-khamsah. Oleh karena itu, konsep maṣlaḥah dalam ḥifẓu al-dīn secara teknis dimaknai sebagai ḥurriyah al-i‘tiqād (kebebasan untuk beragama dan beraliran; dalam ḥifẓu al-nafs sebagai al-karāmāt al-insān (pemuliaan kemanusiaan; dalam ḥifẓu al-nasl sebagai ḥifẓu al-usrah (keutuhan dan keharmonisan keluarga; dalam ḥifẓu al-māl sebagai al-taḍammun al-insān (solidaritas sosial; dan dalam ḥifẓu al-‘aql sebagai al-ḥuqūq al-tarbiyāt (peningkatan sumber daya manusia.

  16. Combustion synthesis of AlB2-Al2O3 composite powders with AlB2 nanowire structures

    Science.gov (United States)

    Yang, Pan; Xiao, Guoqing; Ding, Donghai; Ren, Yun; Yang, Shoulei; Lv, Lihua; Hou, Xing

    2018-05-01

    Using of Al and B2O3 powders as starting materials, and Mg-Al alloy as additives, AlB2-Al2O3 composite powders with AlB2 nanowire structures were successfully fabricated via combustion synthesis method in Ar atmosphere at a pressure of 1.5 MPa. The effect of different amount of Mg-Al alloy on the phase compositions and morphology of the combustion products was investigated. The results revealed that AlB2 and Al2O3 increased, whereas Al decreased with the content of Mg-Al alloy increasing. The impurities MgAl2O4 and AlB12 would exist in the sample with adding of 18 wt% Mg-Al alloy. Interestingly, FESEM/TEM/EDS results showed that AlB2 nanowires were observed in the products when the content of Mg-Al alloy is 6 wt% and 12 wt%. The more AlB2 nanowires can be found as the content of Mg-Al alloy increased. And the yield of AlB2 nanowires with the diameter of about 200 nanometers (nm) and the length up to several tens of micrometers (μm) in the combustion product is highest when the content of Mg-Al alloy is 12 wt%. The vapor, such as Mg-Al (g), B2O2 (g), AlO (g) and Al2O (g), produced during the process of combustion synthesis, reacted with each other to yield AlB2 nanowires by vapor-solid (VS) mechanism and the corresponding model was also proposed.

  17. The effects of boron in TiAl/Ti3Al

    International Nuclear Information System (INIS)

    Feng, C.R.; Michel, D.J.; Crowe, C.R.

    1989-01-01

    The authors discuss the TiAl/Ti 3 Al interfacial misfit dislocations structures investigated by TEM in Ti-45Al alloy and Ti-45Al/TiB 2 composite. For TiAl with c/a = 1.02, only a single set of misfit dislocation arrays are crystallographically possible; these were observed in Ti-45Al alloy. However, the observation of three sets of misfit dislocation arrays in the Ti-45Al/TiB 2 composite suggests that the occupation of octahedral sites in the TiAl structure by excess boron was responsible for a decrease in the c/a ratio leading to an increased fcc character of the TiAl at the TiAl/Ti 3 Al interface

  18. In Situ Fabrication of AlN Coating by Reactive Plasma Spraying of Al/AlN Powder

    Directory of Open Access Journals (Sweden)

    Mohammed Shahien

    2011-10-01

    Full Text Available Reactive plasma spraying is a promising technology for the in situ formation of aluminum nitride (AlN coatings. Recently, it became possible to fabricate cubic-AlN-(c-AlN based coatings through reactive plasma spraying of Al powder in an ambient atmosphere. However, it was difficult to fabricate a coating with high AlN content and suitable thickness due to the coalescence of the Al particles. In this study, the influence of using AlN additive (h-AlN to increase the AlN content of the coating and improve the reaction process was investigated. The simple mixing of Al and AlN powders was not suitable for fabricating AlN coatings through reactive plasma spraying. However, it was possible to prepare a homogenously mixed, agglomerated and dispersed Al/AlN mixture (which enabled in-flight interaction between the powder and the surrounding plasma by wet-mixing in a planetary mill. Increasing the AlN content in the mixture prevented coalescence and increased the nitride content gradually. Using 30 to 40 wt% AlN was sufficient to fabricate a thick (more than 200 µm AlN coating with high hardness (approximately 1000 Hv. The AlN additive prevented the coalescence of Al metal and enhanced post-deposition nitriding through N2 plasma irradiation by allowing the nitriding species in the plasma to impinge on a larger Al surface area. Using AlN as a feedstock additive was found to be a suitable method for fabricating AlN coatings by reactive plasma spraying. Moreover, the fabricated coatings consist of hexagonal (h-AlN, c-AlN (rock-salt and zinc-blend phases and certain oxides: aluminum oxynitride (Al5O6N, cubic sphalerite Al23O27N5 (ALON and Al2O3. The zinc-blend c-AlN and ALON phases were attributed to the transformation of the h-AlN feedstock during the reactive plasma spraying. Thus, the zinc-blend c-Al

  19. Das österreichische Parlament als Akteur der Europäischen Integration – Rechtliche Möglichkeiten und praktische Umsetzung

    Directory of Open Access Journals (Sweden)

    Beatrix Karl

    2015-04-01

    Full Text Available Der vorliegende Beitrag beschäftigt sich mit den Informations- und Mitwirkungsrechten der nationalen Parlamente an der europäischen Gesetzgebung. Die Einflussmöglichkeiten der nationalen Parlamente auf die Tätigkeiten der EU wurden im Rahmen eines Subsidiaritätskontrollmechanismus, der mit dem Vertrag von Lissabon eingeführt wurde, ausgeweitet. Ziel dieses Mechanismus ist es, das Zusammenwirken der EU-Institutionen und der nationalen Parlamente zu stärken und den nationalen Akteuren die Möglichkeit zu geben, zu überprüfen, ob neue Legislativvorschläge der EU mit den Grundsätzen der Subsidiarität und der Verhältnismäßigkeit vereinbar sind. Im Besonderen geht die Verfasserin hierbei auf die Wahrnehmung dieser Mitwirkungsrechte durch das österreichische Parlament ein.

  20. Instability of TiC and TiAl3 compounds in Al-10Mg and Al-5Cu alloys by addition of Al-Ti-C master alloy

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The performance of Al-Ti-C master alloy in refining Al-10Mg and A1-5Cu alloys was studied by using electron probe micro-analyzer (EPMA) and X-ray diffractometer (XRD) analysis.The results indicate that there are obvious fading phenomena in both Al-10Mg and Al-5Cu alloys with the addition of Al-5Ti-0.4C refiner which contains TiC and TiAl3 compounds.Mg element has no influence on the stability of TiC and TiAl3, while TiC particles in Al-10Mg alloy react with Al to form Al4C3 particles, resulting in the refinement fading.However, TiC particles are relatively stable in Al-5Cu alloy, while TiAl3 phase reacts with Al2Cu to produce a new phase Ti(Al, Cu)2, which is responsible for the refinement fading in Al-5Cu alloy.These indicate that the refinement fading will not occur only when both the TiC particles and TiAl3 compound of Al-Ti-C refiner are stable in Al alloys.

  1. PEMAHAMAN HADITS TARBAWI BURHAN AL ISLAM AL ZARNUJI DALAM KITAB TA’LIM AL MUTA’ALLIM

    Directory of Open Access Journals (Sweden)

    Benny Afwadzi

    2017-01-01

    Full Text Available This paper explores the understanding of tarbawi (education hadith from one of the major influential clerics in the Islamic educational system, especially in pesantren. He is Burhan al Islam al Zarnuji with his landmark book Ta’lim al Muta’allim. The conclusion that can be drawn is that al Zarnuji has shades of sufistical view in understanding tarbawi hadith. This can be seen in his understanding of hadith on obligation to seek knowledge (thalab al ilmi faridhatun ‘ala kulli muslimin wa muslimatin, which is interpreted as ilm al hal, the science concerning the condition of the human religious or simplistically said as the religious sciences; and the hadith of intention of studying (innama al a’malu bi al niyyat with the intention for the sake of the hereafter and religion, not mundane. Such an understanding is not something taken for granted, but it can be reinterpreted and perfected in accordance with the spirit of the times of context.

  2. Calculation of Gibbs energy of Zr-Al-Ni, Zr-Al-Cu, Al-Ni-Cu and Zr-Al-Ni-Cu liquid alloys based on quasiregular solution model

    International Nuclear Information System (INIS)

    Li, H.Q.; Yang, Y.S.; Tong, W.H.; Wang, Z.Y.

    2007-01-01

    With the effects of electronic structure and atomic size being introduced, the mixing enthalpy as well as the Gibbs energy of the ternary Zr-Al-Cu, Ni-Al-Cu, Zr-Ni-Al and quaternary Zr-Al-Ni-Cu systems are calculated based on quasiregular solution model. The computed results agree well with the experimental data. The sequence of Gibbs energies of different systems is: G Zr-Al-Ni-Cu Zr-Al-Ni Zr-Al-Cu Cu-Al-Ni . To Zr-Al-Cu, Ni-Al-Cu and Zr-Ni-Al, the lowest Gibbs energy locates in the composition range of X Zr 0.39-0.61, X Al = 0.38-0.61; X Ni = 0.39-0.61, X Al = 0.38-0.60 and X Zr = 0.32-0.67, X Al = 0.32-0.66, respectively. And to the Zr-Ni-Al-Cu system with 66.67% Zr, the lowest Gibbs energy is obtained in the region of X Al = 0.63-0.80, X Ni = 0.14-0.24

  3. Das Mentoring-Programm als soziales Lernarrangement im wissenschaftlichen Qualifikationsprozess: Ein Beitrag zur theoretischen Fundierung von Mentoring-Programmen

    OpenAIRE

    Lödermann, Anne-Marie

    2013-01-01

    Mentoring-Programme sind in den letzten zwei Jahrzehnten zu einem bewährten Instrument der gleichstellungsorientierten Nachwuchsförderung geworden und finden sich nahezu an jeder deutschen Universität. Die konzeptionelle Ausgestaltung der Programme variiert dabei erheblich. Über den Einfluss derartiger Programme auf die wissenschaftliche Karriereentwicklung und über den Stellenwert der arrangierten mentoralen Beziehungen im Gesamtbeziehungsgefüge der teilnehmenden Wissenschaftlerinnen ist bis...

  4. Bipolar characteristics of AlGaN/AlN/GaN/AlGaN double heterojunction structure with AlGaN as buffer layer

    International Nuclear Information System (INIS)

    Peng, Enchao; Wang, Xiaoliang; Xiao, Hongling; Wang, Cuimei; Yin, Haibo; Chen, Hong; Feng, Chun; Jiang, Lijuan; Hou, Xun; Wang, Zhanguo

    2013-01-01

    Highlights: •2DEG and 2DHG coexist in the AlGaN/AlN/GaN/AlGaN DH-structure. •The sheet densities of 2DEG and 2DHG vary with buffer Al content and GaN thickness. •The conditions for the disappearance of 2DHG are discussed. •Increasing buffer Al content provides better electron confinement. •Dislocation scattering is reduced in the DH-structure. -- Abstract: This is a theoretical study of AlGaN/AlN/GaN/AlGaN double heterojunction (DH) structure with AlGaN as buffer layer. Our calculation shows that as the buffer Al content increases, though two-dimensional electron gas (2DEG) sheet density decreases, the channel back-barrier caused by polarization-induced electric field in GaN provides better electron confinement. And under certain conditions the DH-structure shows bipolar characteristics, with an additional two-dimensional hole gas (2DHG) formed at GaN/AlGaN interface. The influence of the buffer Al content and GaN channel thickness on the 2DEG and 2DHG sheet densities are investigated, and the conditions for the disappearance of 2DHG are discussed. Also, the mobility inhibited by dislocation scattering is enhanced in DH-structure due to the enhancement of screening effect of the 2DEG

  5. The code of light: al-ghazali and al-suhrawardi

    OpenAIRE

    Gediminaitė, Barbora

    2017-01-01

    The Code of Light: Al-Ghazali and Al-Suhrawardi The Bachelor’s thesis The Code of Light in Islam: al-Ghazali and al-Suhrawardi presents a comparative study of light. The study analyses the philosophical systems of al-Ghazali and al-Suhrawardi through the reconstruction of the image of light and its operation principles. The main subject of the thesis are the attributes of light. The main problem of the research is the semantics and contextuality of light in Islamic theology and philosophy. Th...

  6. Pemikiran Filosofis Sadra Dalam Tafsir Al-Qur’an Al-Karim : Surah Al-’A‘la

    Directory of Open Access Journals (Sweden)

    Kerwanto Kerwanto

    2014-12-01

    Full Text Available Abstrak : Dalam tafsir atas Surah al-’A‘lā, Mulla Sadra, melalui karyanya Tafsīr al Qur’ān al-Karīm, mengajak jiwa kita berpetualang menuju lapisan makna terdalam untuk mengenali realitas ketauhidan (al- mabdā’, kenabian (shirāth atau nubuwwah dan kebangkitan (ma‘ād dan mengulasnya secara filosofis. Penelitian ini merupakan suatu upaya untuk menggali manfaat dari aspek-aspek penting dari sumber-sumber keagamaan yang tergali dari petunjuk al Qur’an yang berpadu dengan prinsip- prinsip rasional filosofis dan pengalaman mistik (intuitif Sadra. Setiap bab pada tafsir ini diberikan judul dengan tasbīḥ (pernyataan pemujian dan pensucian, dengan tetap memaparkan beragam pokok persoalan terkait metafisika al-Qur’an. Prinsip-prinsip filosofis yang digunakan dalam risalah tafsir ini bisa menjadi salah satu bukti ketidakberjarakan antara filsafat dengan teks-teks keagamaan. Sadra menggunakan metode tafsir yang tetap menerima sisi lahiriah al-Qur’an, dan selanjutnya mencari misteri-misteri, rahasia-rahasia, dan dengan bantuan intelek (akal, intuisi dan iluminasi Tuhan untuk memperoleh realitas-realitas dan makna- makna dibalik selaput ekternalnya (aspek literalnyaKata kunci : Ḥikmah Muta’āliyah, irfan, al-mabdā’, kebangkitan setelah mati, nubuwwah, takwīl, gerak substansial (ḥarakah jawhariyyah, denotasi utama (al-maqshūd al-ashlī, penyempurnaan diri (takammul, tasbīḥ.  Abstract : In his commentary on Surah al-’ A‘lā, Mulla Sadra, through his Tafsīr al-Qur’ān al-Karīm invites our souls to ventureinto the deepest layers of meaning to recognize the reality of Divinity (al- mabdā’, prophethood (Ṣirāṭ or nubuwwah and resurrection (ma‘ād and discusses it in a more philosophical manner. This study is an attempt to explore the benefits of these important aspects of religious sources unearthed from Qur’anic injunctions combined with rational principles of philosophical and mystical experiences

  7. Biological indication of nitric oxides; Zum bioindikativen Nachweis von Stickoxiden

    Energy Technology Data Exchange (ETDEWEB)

    Belotti, E.; Kaemmerer, D.; Mangold, U.; Tempes, D.; Arndt, U.

    1992-12-31

    The authors demonstrate the need for a nitrogen oxide bio-indicator and suggest to use nitrate reductase activity in exposed plant leaves to be established in vivo as the action criterium. Studies on the suitability of different plants and cultivation conditions are presented. Their results are taken to show that large-leaved plants like sunflower or tomato grown with ammonia as the only nitrogen source are best suited for bio-indication of nitric oxides. (orig.) [Deutsch] Der Beitrag zeigt die Notwendigkeit eines Bioindikators fuer Stickoxide auf und schlaegt als Wirkungskriterium die Nitratreduktase-Aktivitaet in den Blaettern exponierter Pflanzen, ermittelt mit der in-vivo-Methode, vor. Untersuchungen zur Eignung verschiedener Pflanzen und Anzuchtbedingungen werden vorgestellt. Aus ihnen ist abzuleiten, dass mit Ammonium als einziger Stickstoffquelle angezogene grossblaettrige Kulturpflanzen, etwa Sonnenblume oder Tomate, am ehesten fuer den bioindikativen Nachweis von Stickoxiden geeignet sind. (orig.)

  8. Habitus ist Macht – politische Partizipation in Parteien

    Directory of Open Access Journals (Sweden)

    Anna-Katharina Meßmer

    2013-03-01

    Full Text Available Der demografische und strukturelle Wandel der Gesellschaft macht auch vor Parteien nicht halt: Offener und diverser müssen ihre Strukturen werden, um den zunehmenden Mitgliederrückgang auszugleichen. Dieser Beitrag untersucht, inwieweit neue Formen der Partizipation und Maßnahmen zur Diversitätsförderung im Kontext sozialer Ungleichheiten wirken können. Dabei soll in der Analyse berücksichtigt werden, wie Parteistrukturen für bislang exkludierte Mitglieder geöffnet werden können. Als Beispiel dient dabei die Sozialdemokratische Partei Deutschlands (SPD, welche sich selbst 2011 per Parteireform einen Wandel hin zur „modernsten Partei Europas“ verordnete. Analysiert wird u. a., welche Inklusions- und Exklusionsbedingungen sich möglicherweise fortschreiben und somit marginalisierte Gruppen weiterhin vom Eintritt und Aufstieg in der SPD abhalten. Als theoretischer Rahmen dienen dabei Geschlechter- und Ungleichheitstheorien.

  9. A united refinement technology for commercial pure Al by Al-10Ti and Al-Ti-C master alloys

    International Nuclear Information System (INIS)

    Ma Xiaoguang; Liu Xiangfa; Ding Haimin

    2009-01-01

    Because flake-like TiAl 3 particles in Al-Ti-C master alloys prepared in a melt reaction method dissolve slowly when they are added into Al melt at 720 deg. C, Ti atoms cannot be released rapidly to play the assistant role of grain refinement, leading to a poor refinement efficiency of Al-Ti-C master alloys. A united refinement technology by Al-10Ti and Al-Ti-C master alloys was put forward in this paper. The rational combination of fine blocky TiAl 3 particles in Al-10Ti and TiC particles in Al-Ti-C can improve the nucleation rate of α-Al. It not only improves the grain refinement efficiency of Al-Ti-C master alloys, but also reduces the consumption

  10. Mono- oder multikulturelle Organisationen? : Managing Diversity auf dem Prüfstand

    OpenAIRE

    Krell, Gertraude

    1996-01-01

    Der Beitrag erläutert aus personalpolitischer Sicht den jeweils einer Unternehmenskultur entsprechenden Umgang mit Homogenität bzw. Heterogenität einer Organisation. Einander gegenübergestellt werden das Leitbild der Homogenität durch Vergemeinschaftung und das Leitbild der Heterogenität durch multikulturelle Vielfalt. "In diesem Beitrag werden zunächst die Funktionsprinzipien der monokulturellen Organisation analysiert und die - von emanzipatorisch bzw. gleichstellungspolitisch Engagierten u...

  11. Was kommt nach dem Handel? Umnutzung von Einzelhandelsflächen und deren Beitrag zur Stadtentwicklung

    OpenAIRE

    Sperle, Tilman

    2012-01-01

    In der Stadt europäischen Typs sind Stadt und Handel eng miteinander verwoben. Die Bedeutung des Handels geht weit über dessen originäre Versorgungsfunktion hinaus. Für die städtischen Zentren und Nebenzentren übernimmt er sowohl gestaltende als auch soziale Funktionen und trägt mit seiner belebenden Wirkung maßgeblich zum urbanen Leben bei. Mit dem tief greifenden Strukturwandel im Einzelhandel verändert sich diese Beziehung zwischen Stadt und Handel dramatisch, Trading-down-Prozesse geh...

  12. Liquidus projection of the Nb-Cr-Al system near the Al3(Nb,Cr) + Cr(Al,Nb) eutectic region

    International Nuclear Information System (INIS)

    Souza, S.A.; Ferrandini, P.L.; Nunes, C.A.; Coelho, A.A.; Caram, R.

    2006-01-01

    The system Nb-Cr-Al was investigated in the region near the Al 3 (Nb,Cr) + Cr(Al,Nb) eutectic and the liquidus projection of that region was determined based on the microstructural characterization of arc melted alloys. The characterization utilized scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results allowed one to determine three primary solidification liquidus surfaces ((Cr,Al) 2 Nb, Cr(Al,Nb) and Al 3 (Nb,Cr)), that are originated from the binary systems Cr-Nb, Cr-Al and Al-Nb. It is proposed the occurrence of the invariant reaction L + (Cr,Al) 2 Nb ↔ Al 3 (Nb,Cr) + Cr(Al,Nb) and of a point of minimum, which involves a three phase reaction, L ↔ Al 3 (Nb,Cr) + Cr(Al,Nb). All alloys studied showed formation of the Al 3 (Nb,Cr) + Cr(Al,Nb) eutectic as the last solidification step with Al(Nb)Cr 2 precipitating from Cr(Al,Nb)

  13. A united refinement technology for commercial pure Al by Al-10Ti and Al-Ti-C master alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ma Xiaoguang [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Liu Xiangfa [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)], E-mail: xfliu@sdu.edu.cn; Ding Haimin [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)

    2009-03-05

    Because flake-like TiAl{sub 3} particles in Al-Ti-C master alloys prepared in a melt reaction method dissolve slowly when they are added into Al melt at 720 deg. C, Ti atoms cannot be released rapidly to play the assistant role of grain refinement, leading to a poor refinement efficiency of Al-Ti-C master alloys. A united refinement technology by Al-10Ti and Al-Ti-C master alloys was put forward in this paper. The rational combination of fine blocky TiAl{sub 3} particles in Al-10Ti and TiC particles in Al-Ti-C can improve the nucleation rate of {alpha}-Al. It not only improves the grain refinement efficiency of Al-Ti-C master alloys, but also reduces the consumption.

  14. Medienpädagogik und E-Learning. Spielt die Medienpädagogik für das E-Learning eine Rolle?

    Directory of Open Access Journals (Sweden)

    Thomas Walden

    2015-03-01

    Full Text Available Der Beitrag von Thomas Walden sieht Medienpädagogik und E-Learning in einem korrelativen Verhältnis. Dabei wird das E-Learning als ein Teilbereich der Medienpädagogik veroret und es werden Argumente dafür geliefert: die Geschwindigkeit digitaler Innovation oder Datenschutz und Datensicherheit ... This text provides media education and e-learning in a correlative relationship. It locates e-learning as a part of the field of media education and provides arguments: the speed of digital innovation, economic estimation of e-learning, data protection and data security, which are currently being compensated at least in rudimentary form by a critical-reflexive media literacy.

  15. Logfile-Analysen zur Evaluation der didaktischen Einbettung von CSCL-Systemen - am Beispiel der CommSy-Nutzung in offenen Seminaren

    Directory of Open Access Journals (Sweden)

    Martin Klein

    2005-02-01

    Full Text Available In unserem Beitrag evaluieren wir die didaktische Einbettung einer CSCL-Anwendung anhand von Logfile-Analysen. Dazu betrachten wir exemplarisch die Nutzung des webbasierten Systems CommSy in einer projektorientierten Lehrveranstaltung, die wir als offenes Seminar charakterisieren. Wir erzielen zwei Ergebnisse: (1 Wir geben Hinweise zur Gestaltung des Nutzungskontexts eines CSCL-Systems sowie zur Unterstützung seiner anfänglichen und kontinuierlichen Nutzung. (2 Wir beschreiben die Analyse von Nutzungsanlässen und -mustern sowie von NutzerInnentypen anhand von Logfiles. Dabei können Logfile-Analysen zur Validierung weiterer Evaluationsergebnisse dienen, sind selbst jedoch nur in Kombination mit zusätzlichen Informationen zum Nutzungskontext interpretierbar.

  16. Medienbildung/LehrerInnenbildung/Bildungspolitik – eine persönliche Nachzeichnung

    Directory of Open Access Journals (Sweden)

    Susanne Krucsay

    2010-03-01

    Full Text Available Medienerziehung, Medienpädagogik, Medienkompetenz, Medienbildung, Media Literacy – alles klar? Die Spurensuche von mehr als 20 Jahren ist kein Beitrag zur Definitionsentwirrung, ich verwende im Folgenden die Begriffe, wie sie sich in dem erwähnten Zeitraum präsentiert haben, synonym. Klarstellen möchte ich lediglich, dass Informatik und E-Learning nur am Rand erwähnt werden; entsprechend dem letzten Stand entspricht demnach Medienbildung der Definition von Media Literacy, einer Fähigkeit, die sich auf die Nutzung, das Verständnis, die kritische Bewertung und die kreative Kommunikation mit den und durch die Medien – analog und digital – bezieht.

  17. Die biene und ihre produkte in der kunst und im alltagsleben (Fruhchristliche und byzantinische Zeit

    Directory of Open Access Journals (Sweden)

    Liveri Angeliki

    2010-01-01

    Full Text Available Die vorliegende Arbeit ist in zwei Teile geteilt: den kunst- und kulturhistorischen Teil. Im ersten Teil werden Darstellungen uber Bienen Bienenzucht, Honig und Wachs seit der fruhchristlichen bis zur spatbyzantinischen Zeit vorgefuhrt. Daher ist es als Beitrag in der "Ikonographie" der Biene wahrend dieser Zeit zu verstehen. Im kulturhistorischen Teil werden Informationen uber die Bienenzucht, den Handel mit Honig und Wachs sowie ihre vielfaltige Anwendung von der byzantinischen Gesellschaft an Hand der primaren Quellen, des Standes der Forschung und der archaologischen Funden erwahnt. Damit ist erwunscht ein moglichst gutes Bild der byzantinischen Bienenzucht wieder zu geben und die Nutzung der Bienenprodukte in Byzanz anschaulich zu machen.

  18. United modification of Al-24Si alloy by Al-P and Al-Ti-C master alloys

    Institute of Scientific and Technical Information of China (English)

    韩延峰; 刘相法; 王海梅; 王振卿; 边秀房; 张均艳

    2003-01-01

    The modification effect of a new type of Al-P master alloy on Al-24Si alloys was investigated. It is foundthat excellent modification effect can be obtained by the addition of this new type of A1-P master alloy into Al-24Simelt and the average primary Si grain size is decreased below 47 μm from original 225 μm. It is also found that theTiC particles in the melt coming from Al8Ti2C can improve the modification effect of the Al-P master alloy. Whenthe content of TiC particles in the Al-24Si melt is 0.03 %, the improvement reaches the maximum and keeps steadywith increasing content of TiC particles. Modification effect occurs at 50 min after the addition of the Al-P master al-loy and TiC particles, and keeps stable with prolonging holding time.

  19. Nanoporous Al sandwich foils using size effect of Al layer thickness during Cu/Al/Cu laminate rolling

    Science.gov (United States)

    Yu, Hailiang; Lu, Cheng; Tieu, A. Kiet; Li, Huijun; Godbole, Ajit; Kong, Charlie

    2018-06-01

    The roll bonding technique is one of the most widely used methods to produce metal laminate sheets. Such sheets offer interesting research opportunities for both scientists and engineers. In this paper, we report on an experimental investigation of the 'thickness effect' during laminate rolling for the first time. Using a four-high multifunction rolling mill, Cu/Al/Cu laminate sheets were fabricated with a range of thicknesses (16, 40, 70 and 130 μm) of the Al layer. The thickness of the Cu sheets was a constant 300 μm. After rolling, TEM images show good bonding quality between the Cu and Al layers. However, there are many nanoscale pores in the Al layer. The fraction of nanoscale pores in the Al layer increases with a reduction in the Al layer thickness. The finite element method was used to simulate the Cu/Al/Cu rolling process. The simulation results reveal the effect of the Al layer thickness on the deformation characteristics of the Cu/Al/Cu laminate. Finally, we propose that the size effect of the Al layer thickness during Cu/Al/Cu laminate rolling may offer a method to fabricate 'nanoporous' Al sandwich laminate foils. Such foils can be used in electromagnetic shielding of electrical devices and noisy shielding of building.

  20. Structural stability and electronic properties of AlCu3, AlCu2Zr in AlZr3: Stabilnost strukture in elektronske lastnosti AlCu3, AlCu2Zr in AlZr3:

    OpenAIRE

    Cheng, Rong; Wu, Xiao-Yu

    2013-01-01

    First-principles calculations were performed to study the alloying stability and electronic structure of the Al-based intermetallic compounds AlCusub3, AlCusub{2}Zr and AlZrsub3. The results show that the lattice parameters obtained after the full relaxation of the crystalline cells are consistent with the experimental data, and these intermetallics have a strong alloying ability and structural stability due to their negative formation energies and their cohesive energies. A further analysis ...

  1. Heimwerken als Protest. Instandbesetzer und Wohnungsbaupolitik in West-Berlin während der 1980er-Jahre

    Directory of Open Access Journals (Sweden)

    Reinhild Kreis

    2017-03-01

    Full Text Available In the early 1980s, hundreds of men and women in many West German and West European cities resorted to a rather unusual form of protest. In order to express their dissatisfaction with the local housing situation and policies, they occupied empty apartment buildings and, under the eyes of an astonished public, began renovating them themselves. Focusing on West Berlin as the most prominent case, this article interprets the performance of DIY home improvement tasks in occupied buildings (Instandbesetzer, as they called themselves as a form of protest, thus drawing attention to the manual work done by squatters and its impact on the housing policies of the 1980s. The DIY measures undertaken publicly by the squatters drew attention to serious political and social shortcomings while at the same time demonstrating possible solutions. The visible (or at least announced transformation of the built environment forced politicians, the public, and experts alike to discuss both housing policy in general and the idea of self-help as suggested by the squatters. Squatters thus accelerated the readjustment of a housing policy which now incorporated manual self-help by tenants into West Berlin’s city planning, but by the same token also undermined the potential for protest and provocation of such practices. * * * Zu Beginn der 1980er-Jahre griffen Hunderte von Männern und Frauen in vielen westdeutschen und westeuropäischen Städten zu einem ungewöhnlichen Mittel, um gegen ihre Wohnsituation und die Wohnungspolitik zu protestieren: Sie begannen, leerstehende Häuser eigenhändig und öffentlichkeitswirksam zu renovieren, die sie vorher besetzt hatten. Am besonders markanten West-Berliner Fall untersucht der Beitrag diese »Instandbesetzer« (so schon die zeitgenössische Selbstbezeichnung als »Heimwerker aus Protest« und fragt nach der Funktion der handwerklichen Praxis im Häuserkampf der 1980er-Jahre. Die Selbsthilfe der Instandbesetzer machte auf Missst

  2. /Cu-Al System

    Science.gov (United States)

    Kish, Orel; Froumin, Natalya; Aizenshtein, Michael; Frage, Nachum

    2014-05-01

    Wettability and interfacial interaction of the Ta2O5/Cu-Al system were studied. Pure Cu does not wet the Ta2O5 substrate, and improved spreading is achieved when relatively a high fraction of the active element (~40 at.% Al) was added. The Al2O3 and AlTaO4 phases were observed at the Ta2O5/Cu-Al interface. A thermodynamic evaluation allowed us to suggest that the lack of wetting bellow 40 at.% Al is due to the presence of a native oxide, which covers the drop. The conditions of the native oxide decomposition and the formation of the volatile Al2O suboxide strongly depend on the vacuum level during sessile drop experiments and the composition of the Cu-Al alloy. In our case, Al contents greater than 40% provides thermodynamic conditions for the formation of Al2O (as a result of Al reaction with Al2O3) and the drop spreading. It was suggested that the final contact angle in the Ta2O5/Cu-Al system (50°) is determined by Ta adsorption on the newly formed alumina interlayer.

  3. Hybride textuelle Strukturen und hybride textuelle Einheiten. Ein Beitrag zur Theorie der Wörterbuchform

    Directory of Open Access Journals (Sweden)

    Herbert Ernst Wiegand

    2011-10-01

    Full Text Available

    ZUSAMMENFASSUNG: In diesem Beitrag wird die Bildung, Darstellung und Leistung von hybriden textuellen Strukturen, die akzessive Einträge aufweisen, am Beispiel von Wörterbuchartikeln behandelt sowie erklärt, welche Eigenschaften hybride textuelle Einheiten haben. Ein Wörterbuchartikel eines Printwörterbuchs weist immer dann neben einer hierarchischen reinen eine hierarchische hybride Textkonstituentenstruktur auf, wenn in ihm mindestens ein funktionaler Angabezusatz auftritt, z.B. ein oben oder unten erweiternder oder ein binnenerweiternder. Da funktionale Angabezusätze Textsegmente mit Angabefunktion aber ohne Textkonstituentenstatus sind, werden sie durch nichtfunktionale Segmentation ermittelt, so dass neben funktionalen auch nichtfunktionale Textsegmente gegeben sind, die dann bei der Strukturbildung in die Trägermengen eingehen, so dass die Trägermengen aller hybriden hierarchischen Strukturen elementenheterogen, während die Trägermengen aller hierarchischen reinen Strukturen elementenhomogen sind. In den Strukturgraphen für hierarchische hybride Artikelstrukturen sind dann die Knoten für diejenigen Textsegmente, die den Hybridstatus der Strukturen bewirken, entweder durch Pfeilkanten für die textarchitektonischen oberhalb/unterhalb-Relationen mit den Knoten für die Textkonstituenten verbunden, so dass die Strukturgraphen architektonisch angereichert sind, oder durch besonders markierte Kanten, die die Knoten für die nichtfunktionalen Textsegmente und die für die binnenerweiternden funktionalen Angabezusätze mit den Knoten für die Textkonstituenten verbinden. Zu jedem Typ von hierarchischer reiner Artikelstruktur gehören mehrere Typen von hybriden Artikelstrukturen; entsprechendes gilt für hierarchische reine Angabestrukturen. Nur eine Auswahl aus den Typologien der hybriden Artikel- und Angabestrukturen wird behandelt sowie eine kleine Auswahl von hybriden textuellen Einheiten, die kriteriale Eigenschaften von zwei

  4. Metodologi Kitab Ma‘alim al-Tanzil Karya Al-Bagawiy

    Directory of Open Access Journals (Sweden)

    M. Rusydi Khalid

    2017-12-01

    This study aims to describe the metodology of Ma'a> lim al-tanzi>l book by al-Bagawi. The book is one of the books of exegesis written on the basis of hadith, which by the commentary scholars recognized avoided from heresy and weak hadith. The author of this book is Imam Abu Humaid Hussein bin Mas‘u>d al-Farra>’ Al-Bagawi al-Syafi‘i>, died in the year 510 H. This exegesis book combines the interpretation of the companions, tabi‘i>n, and tabi‘i> tabi‘i>n. Interpretation is broken down with easy, simple, and concise diction choices. The stoning of the interpretation of the salaf scholars without mentioning the sanad as already mentioned in the introduction to his book. This book was first printed in one edition with the exegesis book of Ibn Kas}i>r and al-kha>zin. This book interprets the Qur'an analytically from the beginning to the end of the surah by using the method of interpretation based on the hadith, namely by mentioning the arguments of the hadith sahih, the fatwa of the companions and the tabi‘i>n. The characteristic or purpose of this book is fiqh oriented, which tends to the Shafi‘i fiqh.   Abstrak Tulisan ini mendeskripsikan metode penafsiran dalam kitab Ma’a>lim al-tanzi>l karya al-bagawi. Kitab tafsir ini merupakan salah satu di antara kitab-kitab tafsir yang ditulis berdasarkan riwayat, yang oleh para ulama tafsir diakui terhindar dari bid’ah dan hadis dhaif (lemah. Penulis buku ini adalah Imam Abu Muhammad Husain bin Mas‘u>d al-Farra>‘ al-Bagawi al-Syafi‘i>, wafat pada tahun 510 H. Kitab ini adalah kitab pertengahan yang mengutip penafsiran para Sahabat, ta>bi‘i>n, dan tabi‘i ta>bi‘i>n. Penafsiran diuraikan dengan pilihan diksi yang mudah, sederhana, dan ringkas. Penukilan dari interpretasi ulama salaf tanpa menyebutkan sanad karena telah disebutkan dalam pendahuluan bukunya. Buku ini pertama kali dicetak dalam satu edisi dengan tafsir Ibn Kas\\i>r dan tafsir al-Kha>zin. Kitab ini menafsirkan al-Qur’an secara

  5. ALS Association

    Science.gov (United States)

    ... toward a world without ALS! Walk to Defeat ALS® Walk to Defeat ALS® draws people of all ... We need your help. I Will Advocate National ALS Registry The National ALS Registry is a congressionally ...

  6. AlN nanoparticle-reinforced nanocrystalline Al matrix composites: Fabrication and mechanical properties

    International Nuclear Information System (INIS)

    Liu, Y.Q.; Cong, H.T.; Wang, W.; Sun, C.H.; Cheng, H.M.

    2009-01-01

    To improve the specific strength and stiffness of Al-based composites, AlN/Al nanoparticles were in-situ synthesized by arc plasma evaporation of Al in nitrogen atmosphere and consolidated by hot-pressing to fabricate AlN nanoparticle-reinforced nanocrystalline Al composites (0-39 vol.% AlN). Microstructure characterization shows that AlN nanoparticles homogeneously distribute in the matrix of Al nanocrystalline, which forms atomically bonded interfaces of AlN/Al. The hardness and the elastic modulus of the nanocomposite have been improved dramatically, up to 3.48 GPa and 142 GPa, respectively. Such improvement is believed to result from the grain refinement strengthening and the interface strengthening (load transfer) between the Al matrix and AlN nanoparticles

  7. Cost of district heating using geothermal energy; Ist geothermische Waerme wirtschaftlich?

    Energy Technology Data Exchange (ETDEWEB)

    Oppermann, G [GRUNEKO AG, Ingenieure fuer Energiewirtschaft, Basel (Switzerland)

    1997-12-01

    The environmental advantages of a district heating network using geothermal energy are obvious. On the other hand utilizing geothermal energy is considered to be very expensive. The goal of this paper is to compare the costs of geothermal energy with other renewable energy sources. Based on the costs of realized plants and projects the following energy sources have been analysed. Geothermal energy, water of tunnel-drainage, waste heat of a sewage disposal platn and waste wood. All plants have a district heating network. The results are a contribution to the actuel discussion about public subsiding of geothermal energy. (orig.) [Deutsch] Die oekologischen Vorteile einer geothermischen Fernwaermeversorgung sind fuer jeden, der Bohrungen in Erwaegung zieht, unschwer erkennbar. Wie steht es aber mit den Kosten einer geothermischen Nutzung? Hier beleben Horrorzahlen wie auch Wunschdenken die Diskussionen. Der Artikel beabsichtigt einen sachlichen Beitrag zu dieser Diskussion uz liefern. Konkrete Bauprojekte im Megawattbereich der GRUNEKO AG werden kostenmaessig nach gleichen Kriterien analysiert und verglichen. Auf goethermischer Seite wird ein Doublettensystem und eine Tunnelwasserwaermenutzung kostenmaessig analysiert. Als Quervergleich werden ebenfalls GRUNEKO-Projekte mit regenerierbaren Energietraegern herangezogen (Holzschnitzelanlage, Klaeranlagenabwaerme, Seewasser-Abkuehlung). Alle Analgen haben Waermeverteilnetze. Die nachgewiesenen Kostendifferenzen zwischen Geothermie und anderen regenerativen Waermversorgungen koennten einen Beitrag leisten zu der gegenwaertig aktuellen `Ueberpruefung staatlicher Foerderungsmassnahmen zugunsten einer verstaerkten Nutzung der Geothermie`. (orig.)

  8. Comparison of one and two-neutron transfer near the Coulomb barrier for the 27Al(18O, 16O)29Al, 27Al(18O, 17O)28Al and 27Al(13C, 12C)28Al reactions

    International Nuclear Information System (INIS)

    Schiller, S.A.; Eck, J.S.

    1975-01-01

    Total reaction cross sections for the transfer reactions 27 Al( 18 O, 16 O) 29 Al, 27 Al( 18 O, 17 O) 28 Al and 27 Al( 13 C, 12 C) 28 Al are reported for center-of-mass energies between 13 and 20 MeV for 18 O projectiles and between 11 and 17.5 MeV for 13 C projectiles. The reaction products, 29 Al, and 28 Al, beta decay to 29 Si and 28 Si, respectively, and the subsequent γ decays of 29 Si and 28 Si were measured. Due to the relatively long beta decay half lives, data were taken in a beam-off mode, resulting in very clean spectra. Total cross sections were calculated and compared with a theoretical model for barrier penetration proposed by C.Y. Wong. Differences between 18 O induced one and two-neutron total transfer reaction cross sections are discussed. (orig.) [de

  9. Al-matrix composite materials reinforced by Al-Cu-Fe particles

    International Nuclear Information System (INIS)

    Bonneville, J; Laplanche, G; Joulain, A; Gauthier-Brunet, V; Dubois, S

    2010-01-01

    Al-matrix material composites were produced using hot isostatic pressing technique, starting with pure Al and icosahedral (i) Al-Cu-Fe powders. Depending on the processing temperature, the final reinforcement particles are either still of the initial i-phase or transformed into the tetragonal ω-Al0 0.70 Cu 0.20 Fe 0.10 crystalline phase. Compression tests performed in the temperature range 293K - 823K on the two types of composite, i.e. Al/i and Al/ω, indicate that the flow stress of both composites is strongly temperature dependent and exhibit distinct regimes with increasing temperature. Differences exist between the two composites, in particular in yield stress values. In the low temperature regime (T ≤ 570K), the yield stress of the Al/ω composite is nearly 75% higher than that of the Al/i composite, while for T > 570K both composites exhibit similar yield stress values. The results are interpreted in terms of load transfer contribution between the matrix and the reinforcement particles and elementary dislocation mechanisms in the Al matrix.

  10. Piezo-tunnel effect in Al/Al2O3/Al junctions elaborated by atomic layer deposition

    Science.gov (United States)

    Rafael, R.; Puyoo, E.; Malhaire, C.

    2017-11-01

    In this work, the electrical transport in Al/Al2O3/Al junctions under mechanical stress is investigated in the perspective to use them as strain sensors. The metal/insulator/metal junctions are elaborated with a low temperature process (≤200 °C) fully compatible with CMOS back-end-of-line. The conduction mechanism in the structure is found to be Fowler-Nordheim tunneling, and efforts are made to extract the relevant physical parameters. Gauge factors up to -32.5 were found in the fabricated devices under tensile stress. Finally, theoretical mechanical considerations give strong evidence that strain sensitivity in Al/Al2O3/Al structures originates not only from geometrical deformations but also from the variation of interface barrier height and/or effective electronic mass in the tunneling oxide layer.

  11. Generation and evolution of nanoscale AlP and Al{sub 13}Fe{sub 4} particles in Al-Fe-P system

    Energy Technology Data Exchange (ETDEWEB)

    Qiao, Huan; Gao, Tong; Zhu, Xiangzhen; Wu, Yuying; Qian, Zhao; Liu, Xiangfa, E-mail: xfliu@sdu.edu.cn

    2015-02-15

    Highlights: • Diffusion and gradual solid reactions between Al and Fe{sub x}P phases in Al-Fe-P alloy were investigated. • Nanoscale AlP clusters are in-situ generated and evolve during the whole process. • This novel Al-Fe-P alloy has an excellent low-temperature refining performance on hypereutectic Al-Si alloy. - Abstract: In this paper, the gradual solid reactions between Al and Fe{sub x}P phases in Al-Fe-P alloy were investigated. The results show that the whole reaction process undergoes four main stages: the diffusion of Al atom, the generation of (Al, Fe, P) intermediate compound, the precipitation of nano AlP and Al{sub 13}Fe{sub 4} clusters and their growth to submicron particles. The microstructure of Fe-P particles evolves from the “egg-type”, the “sponge-type” to the “sesame-cake” structure. AlP and Al{sub 13}Fe{sub 4} nano phases have in-situ generated and evolved during the whole process. The gradual reaction mechanism has been discussed. Furthermore, a novel Al-Fe-P alloy which contains (Al, Fe, P) intermediate compounds and nano AlP particles has been synthesized and its low-temperature refining performance on A390 alloy has also been investigated.

  12. Japanese version of the ALS-FTD-Questionnaire (ALS-FTD-Q-J).

    Science.gov (United States)

    Watanabe, Yasuhiro; Beeldman, Emma; Raaphorst, Joost; Izumi, Yuishin; Yoshino, Hiide; Masuda, Michihito; Atsuta, Naoki; Ito, Satoru; Adachi, Tadashi; Adachi, Yoshiki; Yokota, Osamu; Oda, Masaya; Hanashima, Ritsuko; Ogino, Mieko; Ichikawa, Hiroo; Hasegawa, Kazuko; Kimura, Hideki; Shimizu, Toshio; Aiba, Ikuko; Yabe, Hayato; Kanba, Makoto; Kusumi, Kimiyoshi; Aoki, Tetsuya; Hiroe, Yu; Watanabe, Hirohisa; Nishiyama, Kazutoshi; Nomoto, Masahiro; Sobue, Gen; Nakashima, Kenji

    2016-08-15

    Amyotrophic lateral sclerosis (ALS) and frontotemporal dementia (FTD) share common clinical, genetic and neuropathological features. Some ALS patients have behavioral/personality changes, which could result in significant obstacles in the care provided by family members and caregivers. An easy screening tool would contribute greatly to the evaluation of these symptoms. We translated the ALS-FTD-Questionnaire, developed in the Netherlands, into Japanese (ALS-FTD-Q-J) and examined the clinimetric properties (internal consistency, construct and clinical validity). Patients with ALS and/or behavioral variant FTD (bvFTD) were evaluated alongside healthy controls in this multicenter study. All ALS patients, regardless of bvFTD status, were further evaluated by the frontal behavioral inventory (FBI) and for frontal/executive function, cognition, anxiety/depression, and motor functions. Data from 146 subjects were analyzed: ALS (92), ALS-bvFTD (6), bvFTD (16), and healthy controls (32). The internal consistency of the ALS-FTD-Q-J was good (Cronbach α=0.92). The ALS-FTD-Q-J showed construct validity as it exhibited a high correlation with the FBI (r=0.79). However, correlations were moderate with anxiety/depression and low with cognitive scales, in contrast to the original report, i.e. a moderate correlation with cognition and a low correlation with anxiety/depression. The ALS-FTD-Q-J discriminated ALS patients from (ALS-)bvFTD patients and controls. Thus, the ALS-FTD-Q-J is useful for evaluating Japanese ALS/FTD patients. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Radiation detection with Nb/Al-AlOx/Al/Nb superconducting tunnel junctions

    International Nuclear Information System (INIS)

    Matsumura, Atsuki; Takahashi, Toru; Kurakado, Masahiko

    1992-01-01

    Superconductor radiation detectors have the possibility of 20-30 times better energy resolution than that of a high resolution Si detector. We fabricated Nb/Al-AlOx/Al/Nb superconducting tunnel junctions with low leakage current. X rays were detected with large area junctions of 178x178 μm 2 . High energy resolution of 160 eV for 5.9 keV was obtained. We also fabricated series connected junctions which covers a rather large area of 4x4 mm 2 . α particles injected into the rear substrate were detected using nonthermal phonons induced by the radiations in the substrate. (author)

  14. ALS-Plus Syndrome: Non-Pyramidal Features in a Large ALS Cohort

    Science.gov (United States)

    McCluskey, Leo; Vandriel, Shannon; Elman, Lauren; Van Deerlin, Vivianna M.; Powers, John; Boller, Ashley; Wood, Elisabeth McCarty; Woo, John; McMillan, Corey T.; Rascovsky, Katya; Grossman, Murray

    2014-01-01

    Objective Autopsy studies show widespread pathology in amyotrophic lateral sclerosis (ALS), but clinical surveys of multisystem disease in ALS are rare. We investigated ALS-Plus syndrome, an understudied group of patients with clinical features extending beyond pyramidal and neuromuscular systems with or without cognitive/behavioral deficits. Methods In a large, consecutively-ascertained cohort of 550 patients with ALS, we documented atypical clinical manifestations. Genetic screening for C9orf72 hexanucleotide expansions was performed in 343 patients, and SOD1, TARDBP, and VCP were tested in the subgroup of patients with a family history of ALS. Gray matter and white matter imaging was available in a subgroup of 30 patients. Results Seventy-five (13.6%) patients were identified with ALS-Plus syndrome. We found disorders of ocular motility, cerebellar, extrapyramidal and autonomic functioning. Relative to those without ALS-Plus, cognitive impairment (8.0% vs 2.9%, p=0.029), bulbar-onset (49.3% vs 23.2%, pALS-Plus. Survival was significantly shorter in ALS-Plus (29.66 months vs 42.50 months, p=0.02), regardless of bulbar-onset or mutation status. Imaging revealed significantly greater cerebellar and cerebral disease in ALS-Plus compared to those without ALS-Plus. Conclusions ALS-Plus syndrome is not uncommon, and the presence of these atypical features is consistent with neuropathological observations that ALS is a multisystem disorder. ALS-Plus syndrome is associated with increased risk for poor survival and the presence of a pathogenic mutation. PMID:25086858

  15. Tailoring ultrafine grained and dispersion-strengthened Ti 2 AlC/TiAl ...

    Indian Academy of Sciences (India)

    In situ Ti 2 AlC/TiAl composite was fabricated by hot-pressing method via the reaction system of Ti 3 AlC 2 and Ti-Al pre-alloyed powders at low temperature of 1150 ∘ C. The composite mainly consisted of TiAl, Ti 3 Al and Ti 2 AlC phases. Fine Ti 2 AlC particles were homogeneously distributed and dispersed in the matrix.

  16. Assessing behavioural changes in ALS: cross-validation of ALS-specific measures.

    Science.gov (United States)

    Pinto-Grau, Marta; Costello, Emmet; O'Connor, Sarah; Elamin, Marwa; Burke, Tom; Heverin, Mark; Pender, Niall; Hardiman, Orla

    2017-07-01

    The Beaumont Behavioural Inventory (BBI) is a behavioural proxy report for the assessment of behavioural changes in ALS. This tool has been validated against the FrSBe, a non-ALS-specific behavioural assessment, and further comparison of the BBI against a disease-specific tool was considered. This study cross-validates the BBI against the ALS-FTD-Q. Sixty ALS patients, 8% also meeting criteria for FTD, were recruited. All patients were evaluated using the BBI and the ALS-FTD-Q, completed by a carer. Correlational analysis was performed to assess construct validity. Precision, sensitivity, specificity, and overall accuracy of the BBI when compared to the ALS-FTD-Q, were obtained. The mean score of the whole sample on the BBI was 11.45 ± 13.06. ALS-FTD patients scored significantly higher than non-demented ALS patients (31.6 ± 14.64, 9.62 ± 11.38; p ALS-FTD-Q was observed (r = 0.807, p ALS-FTD-Q. Good construct validity has been further confirmed when the BBI is compared to an ALS-specific tool. Furthermore, the BBI is a more comprehensive behavioural assessment for ALS, as it measures the whole behavioural spectrum in this condition.

  17. Plastic deformation of Al13Fe4 particles in Al-Al13Fe4 by high-speed compression

    International Nuclear Information System (INIS)

    Yoneyama, N.; Mizoguchi, K.; Kumai, S.; Sato, A.; Kiritani, M.

    2003-01-01

    Spray-formed Al-Fe alloys having undergone high-speed deformation were examined under a high-voltage electron microscope. Two types of specimens were examined; one containing fine Al 13 Fe 4 particles, and the other containing large particles. In the former specimen, deformation is found to proceed in three patterns, depending on specimen thickness and strain rate: (1) without deformation of the Al 13 Fe 4 ; (2) breaking of the Al 13 Fe 4 ; or (3) melting of the Al 13 Fe 4 . Local melting is found to alter some of the Al 13 Fe 4 particles, to impart five-fold symmetry in diffraction or an amorphous structure. In the latter specimen, introduction of glide dislocations enabled us to determine a shear system in the mc102 monoclinic c2/m crystal of Al 13 Fe 4 . On the bases of these observations, the mechanism of high-speed deformation is discussed while taking into account the highly stressed and/or heated states of Al 13 Fe 4 embedded in Al matrix

  18. Synthesis and characterization of pillared bentonite with Al, AL/Fe and impregnated with Pd; Sintese e caracterizacao de bentonitas pilarizadas com Al, AL/Fe e impregnadas com Pd

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Marcus Vinicius Costa; Pizarro, Alejandro Herrero; Molina, Carmen Belen, E-mail: marcus.ufpa@yahoo.com.br [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Instituto de Tecnologia. Faculdade de Engenharia Quimica; Seccion de Ingenieria Quimica, Facultad de Ciencias, Universidad Autonoma de Madri (Spain)

    2017-10-01

    In this work, a north american bentonite was pillared with Al and Al/Fe, creating the Al-PILC and Al-Fe-PILC, respectively. Then the Pd was impregnated in the materials, generating Pd-Al-PILC and Pd-Al-Fe-PILC, respectively. The samples were characterized by X-ray diffraction, differential thermal analysis and thermogravimetric and N{sub 2} adsorption at 77 K to determine the specific surface area by BET method (Brunauer - Emmett - Teller). There was an increase in the basal spacing of bentonite from 12.4Å in the original sample to 17.81Å in the Al-Fe-PILC, 17.20Å in Pd-Al-PILC and 17.05Å in the Pd-Al-Fe-PILC. The specific surface area increased from 19.05m{sup 2}/g in the original sample to 173.49m{sup 2}/g in Al-Fe-PILC, 101.31m{sup 2}/g to Pd-Al-PILC and 92m{sup 2}/g in Pd-Al-Fe-PILC. The pillaring process was successful and the synthesized materials have great potential for use as catalysts. (author)

  19. Electrodeposition of Al from a 1-butylpyrrolidine-AlCl3 ionic liquid

    Directory of Open Access Journals (Sweden)

    Giridhar Pulletikurthi

    2015-12-01

    Full Text Available The addition of 1-butylpyrrolidine to AlCl3 results in the formation of an electrolyte that is suited to Al deposition. The feasibility of electrodepositing Al from the synthesized electrolyte was investigated. Several compositions of AlCl3 and 1-butylpyrrolidine were prepared for this purpose. These mixtures show a different phase behavior at various compositions of AlCl3 and 1-butylpyrrolidine. IR, Raman and NMR spectroscopy were employed to characterize the synthesized liquids. Among the prepared compositions, 1:1.2 mol ratio of 1-butylpyrrolidine:AlCl3 and the upper phase of 1:1.3 mol ratio of 1-butylpyrrolidine:AlCl3 were found to be suitable for Al electrodeposition at room temperature (RT. Uniform and thick (~µm thick layers of Al were obtained on copper at RT. Al deposition occured from the cationic species of AlCl3−xLy+ (where x≤2, y=1–2, and L=1-butylpyrrolidine in this electrolyte. This behavior is contrary to the well investigated classic AlCl3 based ionic liquids, where the deposition of Al occurs mainly from anionic Al2Cl7− ions.

  20. Orientation of Al3Ti platelets in Al-Al3Ti functionally graded material manufactured by centrifugal method

    International Nuclear Information System (INIS)

    Watanabe, Y.; Fukui, Y.

    1997-01-01

    Al-Al 3 Ti functionally graded materials (FGMs) were manufactured by the centrifugal method with a commercial ingot of Al-5 mass% Ti master alloy. The alloy was melted at a liquid/solid coexisting temperature, at which Al 3 Ti remains as a solid, and then it was cast into a thick-walled ring. It was found that the Al-Al 3 Ti functionally graded material can be successfully fabricated by the centrifugal method. It was also found that the volume fraction of the Al 3 Ti can be increased by repetition of the centrifugal method. Since the shape of Al 3 Ti particles in a commercial alloy ingot is that of a platelet, the Al 3 Ti particles are arranged with their platelet planes nearly perpendicular to the radial direction. The orientation effects become stronger when the G number becomes larger. Although the final centrifugal casting was conducted under a very large centrifugal force for the specimen cast three times, the orientation effects were weaker than those in the specimen cast one time. From these observations, it is concluded that the origin of orientation of Al 3 Ti platelets can be attributed to the angular velocity gradient of the melt along the radial direction produced by the difference in the viscosity. (orig.)

  1. In situ synthesis of Ti{sub 2}AlC–Al{sub 2}O{sub 3}/TiAl composite by vacuum sintering mechanically alloyed TiAl powder coated with CNTs

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jian [Department of Materials Science and Engineering of Tianjin University, Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China); Zhao, Naiqin, E-mail: nqzhao@tju.edu.cn [State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin (China); Department of Materials Science and Engineering of Tianjin University, Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China); Nash, Philip [Thermal Processing Technology Center, Illinois Institute of Technology, IL (United States); Liu, Enzuo; He, Chunnian; Shi, Chunsheng; Li, Jiajun [Department of Materials Science and Engineering of Tianjin University, Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China)

    2013-11-25

    Highlights: •Using zwitterionic surfactant to enhance the dispersion of the CNTs on the powder surface. •CNTs as carbon source decreased the formation temperature of Ti{sub 2}AlC. •Al{sub 2}O{sub 3} was generated in situ from the oxygen atoms introduced in the drying procedure. •Nanosized Ti{sub 3}Al was precipitated at 1250 °C and distribute in the TiAl matrix homogeneously. •Ti{sub 2}AlC–Al{sub 2}O{sub 3}/TiAl composite was synthesized in situ by sintering pre-alloy Ti–Al coated with CNTs. -- Abstract: Bulk Ti{sub 2}AlC–Al{sub 2}O{sub 3}/TiAl composites were in situ synthesized by vacuum sintering mechanically alloyed Ti–50 at.% Al powders coated with carbon nanotubes (CNTs). The pre-alloyed Ti–50 at.% Al powder was obtained by ball milling Ti and Al powders. The multi-walled carbon nanotubes as the carbon resource were covered on the surface of the pre-alloyed powders by immersing them into a water solution containing the CNTs. A zwitterionic surfactant was used to enhance the dispersion of the CNTs on the powder surface. The samples were cold pressed and sintered in vacuum at temperatures from 950 to 1250 °C, respectively. The results show that the reaction of forming Ti{sub 2}AlC can be achieved below 950 °C, which is 150 °C lower than in the Ti–Al–TiC system and 250 °C lower than for the Ti–Al–C system due to the addition of CNTs. Additionally, the reinforcement of Al{sub 2}O{sub 3} particles was introduced in situ in Ti{sub 2}AlC/TiAl by the drying process and subsequent sintering of the composite powders. Dense Ti{sub 2}AlC–Al{sub 2}O{sub 3}/TiAl composites were obtained by sintering at 1250 °C and exhibited a homogeneous distribution of Ti{sub 2}AlC, Al{sub 2}O{sub 3} and precipitated Ti{sub 3}Al particles and a resulting high hardness.

  2. 27Al NMR studies of NpPd5Al2

    International Nuclear Information System (INIS)

    Chudo, H.; Sakai, H.; Tokunaga, Y.; Kambe, S.; Aoki, D.; Homma, Y.; Shiokawa, Y.; Haga, Y.; Ikeda, S.; Matsuda, T.D.; Onuki, Y.; Yasuoka, H.

    2009-01-01

    We present 27 Al NMR studies for a single crystal of the Np-based superconductor NpPd 5 Al 2 (T c =4.9K). We have observed a five-line 27 Al NMR spectrum with a center line and four satellite lines separated by first-order nuclear quadrupole splittings. The Knight shift clearly drops below T c . The temperature dependence of the 27 Al nuclear spin-lattice relaxation rate shows no coherence peak below T c , indicating that NpPd 5 Al 2 is an unconventional superconductor with an anisotropic gap. The analysis of the present NMR data provides evidence for strong-coupling d-wave superconductivity in NpPd 5 Al 2 .

  3. Magnetic tunnel junctions with AlN and AlNxOy barriers

    International Nuclear Information System (INIS)

    Schwickert, M. M.; Childress, J. R.; Fontana, R. E.; Kellock, A. J.; Rice, P. M.; Ho, M. K.; Thompson, T. J.; Gurney, B. A.

    2001-01-01

    Nonoxide tunnel barriers such as AlN are of interest for magnetic tunnel junctions to avoid the oxidation of the magnetic electrodes. We have investigated the fabrication and properties of thin AlN-based barriers for use in low resistance magnetic tunnel junctions. Electronic, magnetic and structural data of tunnel valves of the form Ta (100 Aa)/PtMn (300 Aa)/CoFe 20 (20 Aa - 25 Aa)/barrier/CoFe 20 (10 - 20 Aa)/NiFe 16 (35 - 40 Aa)/Ta (100 Aa) are presented, where the barrier consists of AlN, AlN x O y or AlN/AlO x with total thicknesses between 8 and 15 Aa. The tunnel junctions were sputter deposited and then lithographically patterned down to 2 x 2μm 2 devices. AlN was deposited by reactive sputtering from an Al target with 20% - 35% N 2 in the Ar sputter gas at room temperature, resulting in stoichiometric growth of AlN x (x=0.50±0.05), as determined by RBS. TEM analysis shows that the as-deposited AlN barrier is crystalline. For AlN barriers and AlN followed by natural O 2 oxidation, we obtain tunnel magnetoresistance >10% with specific junction resistance R j down to 60Ωμm 2 . [copyright] 2001 American Institute of Physics

  4. A study of the Al-rich part of the Al-Re alloy system

    International Nuclear Information System (INIS)

    Balanetskyy, S.; Grushko, B.

    2008-01-01

    The Al-rich part of the Al-Re phase diagram was reinvestigated by scanning and transmission electron microscopy, powder X-ray diffraction and differential thermal analysis. The earlier reported Al 12 Re, Al 6 Re, and Al 11 Re 4 phases were confirmed. Close to the Al 4 Re composition a high-temperature h-Al 4 Re and a low-temperature l-Al 4 Re phase were found to be formed at slightly different compositions. Both exhibited compositional ranges. A new phase was revealed close to the Al 3 Re composition. The Al 11 Re 4 phase is formed congruently at 1650 deg. C, Al 3 Re peritectically at 1610 deg. C, h-Al 4 Re peritectically at 1410 deg. C, l-Al 4 Re peritectically at ∼1000 deg. C, Al 6 Re peritectically at 813 deg. C and Al 12 Re peritectically at 746 deg. C. Finally, the Al 12 Re-(Al) eutectic is formed at 658 deg. C. The Al 3 Re and h-Al 4 Re are decomposed by eutectoid reactions at ∼946 and 833 deg., respectively. The structure of the h-Al 4 Re phase has not yet been clarified, but it is distinctly different from the Al 4 W phase suggested earlier. The structure of l-Al 4 Re was confirmed. The Al 3 Re phase was found to have a monoclinic structure with a = 0.5180(4) nm, b = 3.97641(9) nm, c = 0.4955(3) nm and β = 99.55(7) o

  5. Abu al-Layth al-Libi

    Science.gov (United States)

    2015-02-01

    success. As an Arab participant acknowledged very early on, “the situation was really harsh. All the brothers were tired,” as they lacked food and... glorious battles that occurred during the early Islamic period.133 He stressed the importance of the battlefield as the path to achieve honor and dignity...diaspora in Waziristan. In the words of Walid Othmani, a French jihadi trained by al-Qa`ida in Waziristan in 2008, “[Al-Libi] was someone well-known and

  6. Dynamic oxygen transfer measurements under operating conditions as a basis for the optimization of ventilation systems; Dynamische Sauerstoffeintragsmessungen unter Betriebsbedingungen als Grundlage zur Optimierung von Belueftungssystemen

    Energy Technology Data Exchange (ETDEWEB)

    Libra, J.A.; Biskup, M.; Wiesmann, U. [Technische Univ. Berlin (Germany). Inst. fuer Verfahrenstechnik; Sahlmann, C.; Gnirss, R. [Berliner Wasserbetriebe, Berlin (Germany)

    1999-07-01

    The largest single energy consumer at sewage treatment plants is the ventilation system of activated sludge tanks. This is why controlling and optimizing ventilation systems is the most appropriate approach to the cutting down of energy costs. The present paper reports on measurements of dynamic oxygen transfer by means of the off-gas method under operating conditions at the Berlin-Ruhleben sewage treatment plant. (orig.) [German] Der groesste Einzelenergieverbraucher auf Klaerwerken ist das Belueftungssystem von Belebungsbecken. Deshalb ist die Kontrolle und Optimierung der Belueftungssysteme der geeignete Weg zur Verringerung der Energiekosten. In diesem Beitrag wird ueber Messungen des dynamischen Sauerstoffeintrags mit der Abluft-Methode unter Betriebsbedingungen im Klaerwerk Berlin-Ruhleben berichtet. (orig.)

  7. Crossing Boundaries in Qualitative Research – Entwurf einer empirischen Reflexivität der qualitativen Sozialforschung in Deutschland und den USA

    Directory of Open Access Journals (Sweden)

    Stephanie Bethmann

    2015-04-01

    Full Text Available Der vorliegende Beitrag widmet sich der Analyse von Prozessen der Wissenskonstruktion in der qualitativen Sozialforschung im transatlantischen Vergleich. Basierend auf explorativen Forschungsergebnissen stellen wir mit den Idealtypen engaging und observing zwei Forschungsstile vor, die sich in den Praktiken der Konstruktion von Nähe und Distanz zum Gegenstand deutlich unterscheiden. Beides, Nähe und Distanz, wird dabei nicht als innere Haltung von Forschenden oder als rigoros nationaler Stil verstanden, sondern als Produkte konkreter Arbeitspraktiken, die in Zusammenhang mit nationalen Forschungskonventionen, Rahmenbedingungen und Epistemologien stehen. Gemeinsam ist beiden Interaktionsmustern die zentrale Fundierung im amerikanischen Pragmatismus, wobei die These einer auffallend unterschiedlichen Bezugnahme auf den amerikanischen Pragmatismus in den beiden Länderkontexten diskutiert wird: Stehen in Deutschland vorwiegend dessen erkenntnistheoretische Prämissen im Mittelpunkt, sieht sich die gegenwärtige US-amerikanische Methodenlandschaft eher dessen gesellschaftspolitischen Traditionen verpflichtet. Ausgehend von diesen Beobachtungen wird abschließend die Forderung formuliert, Reflexivität in der qualitativen Sozialforschung stärker auf den Boden empirischer Analysen zu stellen. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1502191

  8. SAP-like ultrafine-grained Al composites dispersion strengthened with nanometric AlN

    International Nuclear Information System (INIS)

    Balog, M.; Krizik, P.; Yan, M.; Simancik, F.; Schaffer, G.B.; Qian, M.

    2013-01-01

    This paper reports the development of novel Sinter-Aluminum-Pulver (SAP)-like Al–AlN nanocomposites via replacing the native Al 2 O 3 thin films on fine Al powder with a large volume fraction of in situ formed nanometric AlN dispersoids. Fine gas-atomized Al powder (d 50 =1.3 µm) compacts were first partially nitrided at 590 °C in flowing nitrogen, controlled by a small addition of Sn (0.3–0.4 wt%), and subsequently consolidated by hot direct extrusion. The resulting Al–AlN composites consisted of submicrometric Al grains reinforced with nanometric AlN dispersoids together with some nanometric Al 2 O 3 dispersoids. An Al–13 vol% AlN nanocomposite fabricated this way achieved exceptional ultimate tensile strength of 227 MPa, yield strength of 195 MPa and Young's modulus of 66 GPa at 300 °C, superior to typical SAP materials and coarse grained Al–AlN composites. In addition, the Al–13 vol% AlN nanocomposite exhibited good thermal stability up to 500 °C. The strengthening mechanism is discussed

  9. Analisis Kecenderungan Manhaj Akidah Shaykh Shams al-Din al-Sumatera’i

    Directory of Open Access Journals (Sweden)

    MOHD HAIDHAR KAMARZAMAN

    2016-12-01

    Full Text Available Shaykh Shams al-Din al-Sumatera'i is a very great and respected scholar during 16th and 17th century of Acheh. His knowledge in various fields recognized by local and international scholars. He had been a Qadi Malik al-’Adil, a religious leader, who became a referred by communities and country during the reign of the three Sultans of Aceh. He has authored nearly 40 pieces of books related to the theology and sufism. This study focuses on the methods used by Shaykh Shams al-Din al-Sumatera'i in his theological writings. This study found that Shaykh Shams al-Din al-Sumatera'i had used six methods in the such writings.

  10. Zur beruflichen Fortbildung der Musiklehrer in Lettland

    Directory of Open Access Journals (Sweden)

    Ligita Stramkale

    2014-12-01

    Full Text Available Die berufliche Fortbildung der Musiklehrer war in Lettland immer ein aktuelles Thema. Vorschriften des lettischen Ministerkabinetts bestimmen die Anforderungen der beruflichen Fortbildung der Lehrer. Diese werden bei der Durchführung vielfältiger Fortbildungsprogramme für die Musiklehrer umgesetzt. Im folgenden Beitrag werden die Besonderheiten der beruflichen Fortbildung der Musiklehrer und eines der Fortbildungsmodule – „Didaktische Modelle des Musikunterrichts“ – analysiert. Die hier referierte empirische Studie versucht, die Einstellungen der Musiklehrer zu den Einflussfaktoren auf die Qualität der beruflichen Fortbildungskurse und deren Lektoren zu erfassen. Als Ergebnis wird auf mehrere Faktoren hingewiesen, die auf die Qualität der beruflichen Fortbildungskurse der Musiklehrer Einfluss nehmen.

  11. The energy-related services are the major sales promotion. Customized electricity and district heat supply technology and services for the newly developed residential area Boerkhauser Feld at Solingen-Aufderhoehe; Die Dienstleistung bringt den (Verkaufs-)Erfolg. Strom- und Waermeversorgung fuer Wohngebiet Boerkhauser Feld in Solingen-Aufderhoehe

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2001-06-01

    The firm COMUNA-metall, Herford, is the contractor and service provider for installation and operation of the electricity and district heat supply systems based on a modular cogeneration plant (CHP system). The residential area will eventually encompass about 450 residential units, all buildings are low-energy houses. The article explains the systems and gives an initial performance report covering 100 existing residential units. (orig./CB) [German] Die Firma COMUNA-metall, Herford, hat als Dienstleister die Erstellung und den Betrieb einer Strom- und Nahwaermeversorgung mit Kraft-Waerme-Kopplung fuer das Wohngebiet uebernommen, das nach Fertigstellung ca. 450 Wohneinheiten in Niedrigenergiebauweise umfassen wird. Der Beitrag schildert die technischen Einrichtungen und eine erste Leistungsbilanz im Bauabschnitt mit 100 Wohneinheiten. (orig./CB)

  12. „Keine unklugen Leute“. Die Durchsetzung des „Stadtumbau Ost“

    Directory of Open Access Journals (Sweden)

    Matthias Bernt

    2017-06-01

    Full Text Available Der Beitrag untersucht die Herausbildung des Bund-Länder-Programms „Stadtumbau Ost“ um die Jahrtausendwende. Er analysiert dabei das Zusammenwirken von Interessen, Ideen und Akteuren, die diesem (damals neuartigen Ansatz der deutschen Stadtentwicklungspolitik zugrunde lag. In der empirischen Analyse wird deutlich, dass der Stadtumbau in seiner Genese nur als „Hybrid“ aus einem Rettungsprogramm für die ostdeutsche Wohnungswirtschaft und weitergehenden strategischen Planungsansprüchen für die „schrumpfende Stadt“ adäquat verstanden werden kann. Das Zustandekommen dieser doppelten Orientierung spiegelt gleichzeitig die Durchsetzungsstärke einzelner „Schlüsselpersonen“ wieder, denen es gelang, auf die Ausrichtung des im Entstehen begriffenen Programms  prägenden Einfluss zu nehmen.

  13. ZUR WASSERMETAPHORIK IN PHRASEOLOGISMEN DER WIRTSCHAFTSSPRACHE. EINE KOGNITIVE STUDIE ANHAND DES DEUTSCHEN UND SPANISCHEN DER WIRTSCHAFTSSPRACHE. EINE KOGNITIVE STUDIE ANHAND DES DEUTSCHEN UND SPANISCHEN

    Directory of Open Access Journals (Sweden)

    Alfonso Corbacho Sánchez

    2009-10-01

    Full Text Available Ausgehend von der konzeptuellen Metapher GELD IST WASSER ist das Anliegendieses Beitrages, Gemeinsamkeiten und Unterschiede der deutschen Phraseologismen und ihrer Entsprechungenim Spanischen aufzuzeigen. Die Gegenüberstellung dieser Redewendungen soll, zum einen, alsHilfsmittel im Fremdsprachenunterricht dienen, zum anderen, zu Übersetzungsaufgaben benutzt werden.Auch für das Erlernen von wirtschaftlichen Begriffen wäre die vorliegende Untersuchung überaus nützlich.This paper focuses on the German and the Spanish metaphoric expressions that stem from theconceptual metaphor MONEY IS WATER. A contrastive analysis of these expressions shows that they areuseful tools not only to understand some key economic notions but also for translators and teachers of Germanor Spanish as a second language.

  14. Emotionalisierung der Nachhaltigkeitskommunikation

    DEFF Research Database (Denmark)

    Pedersen, Anne Grethe Julius

    Nachhaltigkeitskommunikation (Brugger 2010: 3f). Untersucht wird das Potenzial kommunikativer Handlungen über soziales und ökologisches Engagement, bestimmte Gefühle bei den Empfängern hervorzurufen und eine emotionale Bindung zum Unternehmen herzustellen, u.a. durch emotive Ausdrücke und Bilder, Intensivierungen und...... emotional (mehr als rational) angesprochen - Welche Emotionalisierungsstrategien werden benutzt - Inwieweit unterscheidet sich die deutschsprachige Nachhaltigkeitskommunikation von der dänischsprachigen. Das Textkorpus umfasst online verfügbare Nachhaltigkeitskommunikation auf Websites und in neuen Medien......Die Nachhaltigkeitskommunikation gewinnt an Umfang und Bedeutung und immer öfter werden bei der Bewertung von Unternehmen durch z.B. Investoren und Kunden auch nicht-finanzielle Aspekte herangezogen. Im Fokus des vorliegenden Beitrags steht die emotionale Dimension der unternehmerischen...

  15. Evaluation der Kurse 'Deutsch als Fremdsprache' im Akademischen Auslandsamt Siegen : ein Beitrag zur Qualitätssicherung und -entwicklung

    OpenAIRE

    Moll, Katharina

    2011-01-01

    Der Begriff "Qualität" im Kontext von Lehre und Unterricht ist schon seit Jahren in aller Munde. Nicht erst, aber insbesondere seit der Veröffentlichung der ersten PISA-Studie fordern Politiker umfassende Managementsysteme zur Verbesserung der Qualität von Bildungseinrichtungen in Deutschland. In diesem Zusammenhang wurden in den letzten Jahren viele Ideen entwickelt, die helfen sollen, die Qualität der Bildung zu verbessern. Vor allem für den schulischen Bereich, der besonders unter Druck ge...

  16. Ultrasonic spot welding of Al/Mg/Al tri-layered clad sheets

    International Nuclear Information System (INIS)

    Macwan, A.; Patel, V.K.; Jiang, X.Q.; Li, C.; Bhole, S.D.; Chen, D.L.

    2014-01-01

    Highlights: • The optimal welding condition is achieved at 100 J and 0.1 s. • Failure load first increases and then decreases with increasing welding energy. • The highest failure load after welding is close to that of the clad sheets. • At low energy levels failure occurs in the mode of interfacial failure. • At high energy levels failure takes place at the edge of nugget region. - Abstract: Solid-state ultrasonic spot welding (USW) was used to join Al/Mg/Al tri-layered clad sheets, aiming at exploring weldability and identifying failure mode in relation to the welding energy. It was observed that the application of a low welding energy of 100 J was able to achieve the optimal welding condition during USW at a very short welding time of 0.1 s for the tri-layered clad sheets. The optimal lap shear failure load obtained was equivalent to that of the as-received Al/Mg/Al tri-layered clad sheets. With increasing welding energy, the lap shear failure load initially increased and then decreased after reaching a maximum value. At a welding energy of 25 J, failure occurred in the mode of interfacial failure along the center Al/Al weld interface due to insufficient bonding. At a welding energy of 50 J, 75 J and 100 J, failure was also characterized by the interfacial failure mode, but it occurred along the Al/Mg clad interface rather than the center Al/Al weld interface, suggesting stronger bonding of the Al/Al weld interface than that of the Al/Mg clad interface. The overall weld strength of the Al/Mg/Al tri-layered clad sheets was thus governed by the Al/Mg clad interface strength. At a welding energy of 125 J and 150 J, thinning of weld nugget and extensive deformation at the edge of welding tip caused failure at the edge of nugget region, leading to a lower lap shear failure load

  17. KITAB AL-SANĪ AL-MAṬĀLIB: INTERKONEKSI NAHWU DAN TASAWUF

    Directory of Open Access Journals (Sweden)

    Zakiyah Zakiyah

    2012-12-01

    Tulisan ini mereview buku yang berjudul al-Sanī al-Maṭālib yang ditulis oleh Kiai Nur Iman Mlangi Yogyakarta. Buku ini ditulis dalam bahasa Arab yang me­ngandung interkoneksi antara ilmu Nahwu (tata bahasa Arab dengan mis­tisis­me. Buku ini sangat menarik karena kenyataan bahwa kedua pengetahuan tersebut memiliki aturan sendiri-sendiri. Selain itu, sangat sedikit penulis yang menulis dengan gaya seperti itu. Salah satunya adalah Syaikh Abdul Qadir bin Ahmad al-Kuhany dengan karyanya yang berjudul Manniyat al-Fāqir al-Munjarid wa Sayrat al-Murīd al-Mutafarrid. Buku al-Saniy al-Muthalib diduga telah ditulis pada akhir abad ke-18 atau awal abad ke-19, menurut periode kehidupan Kiai Nur Iman yaitu sekitar pertengahan abad ke-18. Aturan Nahwu dalam buku ini dijelaskan secara teosofi yang dimulai dengan penjelasan mengenai tauhid (keesaan Tuhan sebagai kajian dasar bagi orang Islam, yang diikuti dengan makna dari masing-masing aturan bahasa Arab dalam aspek mistiknya.

  18. Particle reduction strategies - PAREST. Evaluation of emission reduction scenarios using chemical transport calculations. PM10- and NO{sub 2}-immission contributions in Germany. Wood combustion in small combustion systems; installations of the 13th and 17th BImSchV (Federal Immission Control Act). Sub-report.; Strategien zur Verminderung der Feinstaubbelastung - PAREST. Bewertung von Emissionsminderungsszenarien mit Hilfe chemischer Transportberechnungen. PM10- und NO{sub 2}-Immissionsbeitraege in Deutschland. Holzverbrennung in Kleinfeuerungsanlagen, Anlagen der 13. und 17. BImSchV. Teilbericht

    Energy Technology Data Exchange (ETDEWEB)

    Stern, Rainer [Freie Univ. Berlin (Germany). Inst. fuer Meteorologie, Troposphaerische Umweltforschung

    2013-06-15

    This report was prepared within the research project ''Particle reduction strategies - PAREST.'' In this paper with the chemical transport model REM CALGRID following questions were investigated: 1 What is the contribution of the wood-fired small combustion plants in Germany to the PM10- and NO {sub 2}-concentrations? 2 What is the contribution of the 13th and 17th BlmSchV covered installations to the PM10 and NO{sub 2} concentrations in Germany? [German] Der vorliegende Bericht wurde im Rahmen des Forschungs- und Entwicklungsvorhabens ''Strategien zur Verminderung der Feinstaubbelastung'' erstellt. In dem Beitrag werden mit dem chemischen Transportmodell REM-CALGRID folgende Fragestellungen untersucht: 1. Wie hoch ist der Beitrag der mit Holz beheizten Kleinfeuerungsanlagen in Deutschland zu den PM10- und den NO{sub 2}-Konzentrationen? 2. Wie hoch ist der Beitrag der von der 13. und 17. BImSchV erfassten Anlagen zu den PM10-und NO-2-Konzentrationen in Deutschland?.

  19. Rekonstruksi Konsep Ijtihad: Studi Pemikiran Ben’umar tentang al-Ijtihad fi al-Waqi’

    Directory of Open Access Journals (Sweden)

    Duski Ibrahim

    2015-10-01

    Full Text Available This paper is the result of a research that evaluating the reconstruction the concept of ijtihad, by discuss the idea of al-Ijtihad Ben'umar fi al-waqi’. This paper concludes that Al-Ijtihad fi al-waqi’ is actually a form of collective ijtihad (al ijtihad al-jama'i, by gathering the experts of shari'ah law (fuqaha` ash-shar'i and experts Researchers and scientists (khubara` al-'ashr. Because experts know the nash purposes, while researchers and scientists (al-khubara` know the reality (al-waqi’, the effects in the future (ma'alat = future effect and challenges (tahaddiyat. The idea of formulating the concept of al-ijtihad fi al-waqi’ emerged based on a premise that ijtihad is a creation of experts to implement Islamic law in society. Therefore, the concept of ijtihad experienced a significant development, start from using the nash from the language aspects, continue to the using of logic. At the moment when the situation people are increasingly develop, then the creation of ijtihad become a necessary to developed, for example in the form of al-ijtihad fi al-waqi’ . About the source of the formation of the concept of al -ijtihad fi al-waqi’ comes from theory about the functions of nash, al-manath theory in Islamic law, and supported by the theory of al-mashlalah al-mursalah.

  20. Study of the 26Al(n,p)26Mg and 26Al(n,α)23Na reactions using the 27Al(p,p')27Al inelastic scattering reaction

    International Nuclear Information System (INIS)

    Benamara, S; De Séréville, N; Hammache, F; Stefan, I; Roussel, P; Ancelin, S; Assié, M; Guillot, J; Le Crom, B; Lefebvre, L; Adsley, P; Laird, A M; Barton, C; Diget, C; Fox, S; Coc, A; Deloncle, I; Hamadache, C; Kiener, J; Lefebfre-Schuhl, A

    2016-01-01

    26 Al was the first cosmic radioactivity ever detected in the galaxy as well as one of the first extinct radioactivity observed in refractory phases of meteorites. Its nucleosynthesis in massive stars is still uncertain mainly due to the lack of nuclear information concerning the 26 Al(n,p) 26 Mg and 26 Al(n,α) 23 Na reactions. We report on a single and coincidence measurement of the 27 Al(p,p') 27 Al(p) 26 Mg and 27 Al(p,p') 27 Al(α) 23 Na reactions performed at the Orsay TANDEM facility aiming at the spectroscopy study of 27 Al above the neutron threshold. Fourteen states are observed for the first time within 350 keV above the 26 Al+n threshold. (paper)

  1. AlN/Al dual protective coatings on NdFeB by DC magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Li Jinlong; Mao Shoudong; Sun Kefei [Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Li Xiaomin [Shanghai Institute of Ceramics Chinese Academy of Sciences, Shanghai 200050 (China); Song Zhenlun [Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)], E-mail: songzhenlun@nimte.ac.cn

    2009-11-15

    AlN/Al dual protective coatings were prepared on NdFeB by DC magnetron sputtering in a home-made industrial apparatus. Comparing with Al coating, AlN/Al coatings have a denser structure of an outmost AlN amorphous layer following an inner Al columnar crystal layer. The coatings and NdFeB substrate combine well, and moreover, there is occurrence of metallurgy bonding in the interface layer. Both Al and AlN/Al coatings have a good protective ability to NdFeB. Especially, the corrosion resistance of AlN/Al coated NdFeB is improved largely. AlN/Al and Al protective coatings not only do not deteriorate the magnetic properties of NdFeB, but contribute to their slight increase.

  2. AlN/Al dual protective coatings on NdFeB by DC magnetron sputtering

    International Nuclear Information System (INIS)

    Li Jinlong; Mao Shoudong; Sun Kefei; Li Xiaomin; Song Zhenlun

    2009-01-01

    AlN/Al dual protective coatings were prepared on NdFeB by DC magnetron sputtering in a home-made industrial apparatus. Comparing with Al coating, AlN/Al coatings have a denser structure of an outmost AlN amorphous layer following an inner Al columnar crystal layer. The coatings and NdFeB substrate combine well, and moreover, there is occurrence of metallurgy bonding in the interface layer. Both Al and AlN/Al coatings have a good protective ability to NdFeB. Especially, the corrosion resistance of AlN/Al coated NdFeB is improved largely. AlN/Al and Al protective coatings not only do not deteriorate the magnetic properties of NdFeB, but contribute to their slight increase.

  3. Al-Si/Al2O3 in situ composite prepared by displacement reaction of CuO/Al system

    Directory of Open Access Journals (Sweden)

    Zhang Jing

    2010-02-01

    Full Text Available Al2O3 particle-reinforced ZL109 composite was prepared by in situ reaction between CuO and Al. The microstructure was observed by means of OM, SEM and TEM. The Al2O3 particles in sub-micron sizes distribute uniformly in the matrix, and the Cu displaced from the in situ reaction forms net-like alloy phases with other alloy elements. The hardness and the tensile strength of the composites at room temperature have a slight increase as compared to that of the matrix. However, the tensile strength at 350 ℃ has reached 90.23 MPa, or 16.92 MPa higher than that of the matrix. The mechanism of the reaction in the CuO/Al system was studied by using of differential scanning calorimetry(DSC and thermodynamic calculation. The reaction between CuO and Al involves two steps. First, CuO reacts with Al to form Cu2O and Al2O3 at the melting temperature of the matrix alloy, and second, Cu2O reacts with Al to form Cu and Al2O3 at a higher temperature. At ZL109 casting temperature of 750–780 ℃, the second step can also take place because of the effect of exothermic reaction of the first step.

  4. AlGaN nanocolumns and AlGaN/GaN/AlGaN nanostructures grown by molecular beam epitaxy

    Energy Technology Data Exchange (ETDEWEB)

    Ristic, J.; Sanchez-Garcia, M.A.; Ulloa, J.M.; Calleja, E. [Departamento de Ingenieria Electronica, ETSI Telecomunicacion, Universidad Politecnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain); Sanchez-Paramo, J.; Calleja, J.M. [Departamento de Fisica de Materiales, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Jahn, U.; Trampert, A.; Ploog, K.H. [Paul-Drude-Institut fuer Festkoerperelektronik, Hausvogteiplatz 5-7, 10117 Berlin (Germany)

    2002-12-01

    This work reports on the characterization of hexagonal, single crystal AlGaN nanocolumns with diameters in the range of 30 to 100 nm grown by molecular beam epitaxy on Si(111) substrates. The change of the flux ratio between the Al and the total III-element controls the alloy composition. The Al composition trend versus the Al flux is consistent both with the E{sub 2} phonon energy values measured by inelastic light scattering and the luminescence emission peaks position. High quality low dimensional AlGaN/GaN/AlGaN heterostructures with five GaN quantum discs, 2 and 4 nm thick, embedded into the AlGaN columns, were designed in order to study the quantum confinement effects. (Abstract Copyright [2002], Wiley Periodicals, Inc.)

  5. KONSEPSI AL-QURAN DAN AL-HADITS TENTANG OPERASIONAL BANK SYARIAH

    Directory of Open Access Journals (Sweden)

    Muhammad Ardy Zaini

    2015-01-01

    Full Text Available Islam hadir dengan beberapa tujuan, diantaranya adalah terciptanya khoirul ummah dan rahmatan lil’alamin dengan al-Qur’an dan al-Hadits sebagai penuntun umat Islam demi tercapainya tujuan tersebut. Sebagai pedoman hidup, al-Qur’an dan al-Hadits memberikan berbagai petunjuk tentang keteraturan dan permasalahan hidup, termasuk didalamnya mengenai perbankan yang telah memenuhi hampir separuh sisi-sisi kehidupan manusia. Untuk memaksimal ajaran syariah secara kaffah, maka nilai-nilai yang terdapat dalam al-Quran harus mampu diturunkan pada tataran praktis. Salah satu usaha dan langkah dalam rangka menemukan formula perbankan masa depan, al-Quran dan Hadits memiliki konsepsi dalam kegiatan operasional Bank Syariah. Hal ini dilakukan untuk membentuk sikap mental atau watak yang terjabarkan dalam pola berpikir, cara berbicara, dan etika bertingkah laku, sebagai ekspresi jiwa dari manusia yang beriman dan bertakwa kepada Allah Swt. Agar umat Islam mampu menjadi umat yang unggul (khayr ummah.

  6. Fabrication of AlN-TiC/Al composites by gas injection processing

    Institute of Scientific and Technical Information of China (English)

    YU Huashun; CHEN Hongmei; MA Rendian; MIN Guanghui

    2006-01-01

    The fabrication of AlN-TiC/Al composites by carbon-and nitrogen-containing gas injection into Al-Mg-Ti melts was studied. It was shown that AlN and TiC particles could be formed by the in situ reaction of mixture gas (N2+C2H2+NH3) with Al-Mg-Ti melts. The condition for the formation of AlN was that the treatment temperature must be higher than 1373 K, and the amounts of AlN and TiC increased with the increase of the treatment temperature and the gas injection time.It was considered that AlN was formed by the direct reaction of Al with nitrogen-containing gas at the interface of the gas bubble and the melt. However, the mechanism of TiC formation is a combination mechanism of solution-precipitation and solid-liquid reaction.

  7. The formation of AlB2 in an Al-B master alloy

    International Nuclear Information System (INIS)

    Wang Xiaoming

    2005-01-01

    The formation of borides in an Al-3 wt.%B master alloy, produced via chemical reactions of KBF 4 and aluminium has been investigated. The chemical reactions produce boron, which dissolves into molten aluminium and subsequently forms aluminium borides. Backscattered electron imaging (BEI) of the Al-3 wt.%B master alloy under a scanning electron microscope (SEM) revealed the presence of two types of phases that contain different levels of boron. Combined with X-ray diffraction (XRD) results, the two types of phases are identified as AlB 2 on AlB 12 . This gives a direct evidence for a peritectic reaction of AlB 12 and aluminium, which produces AlB 2 . The thermodynamic properties of the reactions that may be involved are examined, and the presence of AlB 12 phase in the master alloy explained. The observed microstructure is explained according to the peritectic reaction in an Al-B phase diagram. The stability of AlB 2 and AlB 12 at lower temperature than 975 deg. C is clarified

  8. Construction and evaluation of multi-component Zn-Al based bearing alloys (Zn-Al-Si, Zn-Al-Cu)

    International Nuclear Information System (INIS)

    Shahmiri, M.; Shahin, K.

    2001-01-01

    Zn-Al based alloys, with excellent mechanical properties, are finding increasing applications in various industries, especially bearing and bushing fields. Observed dimensional instabilities, in their multicomponent systems, (e. g. Zn-Al-Si and, Zn-Al Si-Cu), is believed to be as the result of some kinds of phase transformation, due to the temperature variations, while in service. Profound understanding of the phase transformations due to the temperature variation, requires detailed evaluations of the isothermal sections of the multi-components phase diagrams of Zn-Al-Si and, Zn-Al-Si-Cu alloy systems. In the present article, the isothermal sections of the aforementioned ternary and quaternary systems in the solid state regions have been investigated and observed phase transitions have been critically evaluated

  9. „Das Leben ist nur ein Spiegel“ – Schopenhauers kritischer Lebensbegriff

    Directory of Open Access Journals (Sweden)

    Matthias Kossler

    2012-09-01

    Full Text Available http://dx.doi.org/10.5007/1677-2954.2012v11nesp1p1   Schopenhauer gilt als Vorreiter oder erster Vertreter der Lebensphilosophie, wie sie später von Dilthey, Nietzsche, Bergson und anderen entfaltet wurde. Im Unterschied zur klassischen Lebensphilosophie und zu den an sie anknüpfenden ethischen Entwürfen wird das Leben bei Schopenhauer aber nicht als Zweck betrachtet, sondern als Mittel zu einem anderen Zweck, nämlich für die Ethik, die in der Verneinung des Willens zum Leben gipfelt. Schon in den frühesten handschriftlichen Aufzeichnungen verwendet Schopenhauer verschiedene Metaphern, um das Leben als Medium der ethischen Erkenntnis zu charakterisieren. Besonders häufig tritt dabei das Bild vom Leben als Spiegel auf, in dem der Mensch sein eigenes Wesen und damit auch das Wesen der Welt erblickt. Im Hauptwerk wird dann dieses Bild vom Begriff der Objektivation des Willens abgelöst. Insofern die höchste und deutlichste Objektivation des Willens der Lebenslauf des menschlichen Individuums darstellt, ist Schopenhauers Lebensbegriff eng mit seiner Charakterlehre verknüpft. In dem Beitrag wird das verwickelte Verhältnis von Leben, Erkennen und Ethik vor dem Hintergrund der proto-hermeneutischen Metaphysikkonzeption Schopenhauers anhand der Entwicklung der Spiegelmetapher betrachtet.

  10. Driver assistance - Firstly a contribution to primary safety or rather to comfort?; Fahrerassistenz primaer zum Komfort oder fuer die Sicherheit?

    Energy Technology Data Exchange (ETDEWEB)

    Bubb, H. [TU Muenchen, Garching (Germany). Lehrstuhl fuer Ergonomie

    2003-07-01

    Doubtless assistance systems should contribute to the safety of car driving. They support simultaneously a comfortable use of the car. Especially the operation comfort is characterised by clarity, self explaining, robustness against errors, and so on. Operation comfort doesn't give an inessential contribution to a reliable and appropriate interaction between driver and vehicle that means also a contribution to a reliable function of the total system and thereby to safety. Therefore the subjective experience of assistance systems is of excellent importance with view on the subjective and public confidence in new assistance systems. Are they seen rather as a gain of comfort, as it is preferred by the producer by reasons of production related liability, or as an easing of the driver's behaviour providing safety? Consists in the last called tendency a new kind of danger? In this connection juristic problems may not be unmentioned. The driver may not or not completely be called to account for procedures on which he has no influence or thinks to have no influence. In this case the account for the not compensated damage is contributed to the producer of the system. Therefore, by considering human characteristics and abilities of the driver during the development of assistance systems unwanted juristic consequences should be prevented. (orig.) [German] Assitenzsysteme sollen zweifellos einen Beitrag fuer die Sicherheit des Autofahrers liefern. Zugleich dienen sie aber auch fuer eine komfortable Nutzung des Fahrzeugs. Speziell der Bedienkomfort ist durch leichte Verstaendlichkeit, Selbsterklaerbarkeit, Fehlerrobustheit u.ae. charakterisiert. Durch ihn wird ein nicht unwesentlicher Beitrag zur sicheren und zweckdienlichen Interaktion zwischen Fahrer und Fahrzeug geleistet, also auch ein Beitrag fuer die zuverlaessige Funktion des Systems und damit fuer die Sicherheit. Von herausragender Bedeutung insbesondere im Hinblick auf das subjektive und das oeffentliche

  11. The Existence of a Designer Al=Al Double Bond in the LiAl2 H4- Cluster Formed by Electronic Transmutation.

    Science.gov (United States)

    Lundell, Katie A; Zhang, Xinxing; Boldyrev, Alexander I; Bowen, Kit H

    2017-12-22

    The Al=Al double bond is elusive in chemistry. Herein we report the results obtained via combined photoelectron spectroscopy and ab initio studies of the LiAl 2 H 4 - cluster that confirm the formation of a conventional Al=Al double bond. Comprehensive searches for the most stable structures of the LiAl 2 H 4 - cluster have shown that the global minimum isomer I possesses a geometric structure which resembles that of Si 2 H 4 , demonstrating a successful example of the transmutation of Al atoms into Si atoms by electron donation. Theoretical simulations of the photoelectron spectrum discovered the coexistence of two isomers in the ion beam, including the one with the Al=Al double bond. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Characterization of N-polar AlN in GaN/AlN/(Al,Ga)N heterostructures grown by metal-organic chemical vapor deposition

    Science.gov (United States)

    Li, Haoran; Mazumder, Baishakhi; Bonef, Bastien; Keller, Stacia; Wienecke, Steven; Speck, James S.; Denbaars, Steven P.; Mishra, Umesh K.

    2017-11-01

    In GaN/(Al,Ga)N high-electron-mobility transistors (HEMT), AlN interlayer between GaN channel and AlGaN barrier suppresses alloy scattering and significantly improves the electron mobility of the two-dimensional electron gas. While high concentrations of gallium were previously observed in Al-polar AlN interlayers grown by metal-organic chemical vapor deposition, the N-polar AlN (Al x Ga1-x N) films examined by atom probe tomography in this study exhibited aluminum compositions (x) equal to or higher than 95% over a wide range of growth conditions. The also investigated AlN interlayer in a N-polar GaN/AlN/AlGaN/ S.I. GaN HEMT structure possessed a similarly high x content.

  13. KRITIK ATAS KRITIK EPISTEMOLOGI TAFSIR M. ABIED AL JABIRI: Studi Kritis atas Madkhal ila al Quran al Karim

    Directory of Open Access Journals (Sweden)

    Ahmad Fawaid

    2015-12-01

    Full Text Available This paper critically views the epistemology of Muhammad Abid al Jabiri’s interpretation in his book, Madkhal ila al Quran al Karim. His latest work is projected to make the Quran relevant to mankind today and with certainly critiquing classical Quranic studies that have been constructed by previous scholars. Starting from Arab criticism, which is expected to synergize the gap between Turath and modernity, al Jabiri tried out his theory in the realm of Quranic studies oriented to maintain its originality and interpretation from sectarian influence. Focusing on al Jabiri’s review on the Quran, this paper examines and associates some of the problems with the epistemology of critique in Arab reasoning. Finally, it is inferred that the epistemologic offer of al Jabiri used in Turath is not fully applicable in Quranic studies for several reasons. First, the Quranic studies existed within the chain of sanad in its formation. Secondly, at the application stage, al Jabri often overlooked the sanad and narrations from the companions.

  14. Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

    International Nuclear Information System (INIS)

    Li, Shuo; Bhushan, Bharat

    2016-01-01

    Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

  15. Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

    Energy Technology Data Exchange (ETDEWEB)

    Li, Shuo [School of Materials Science and Technology, China University of Geosciences (Beijing), 29 Xueyuan Road, Haidian Distract, Beijing 100083 (China); Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States); Bhushan, Bharat, E-mail: bhushan.2@osu.edu [Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States)

    2016-08-15

    Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

  16. Dakwah Kultural Bayt al-Qur’an al-Akbar Ukiran Kayu Khas Melayu Palembang

    Directory of Open Access Journals (Sweden)

    Reza Pahlevi

    2016-07-01

    Full Text Available Penelitian ini berusaha mengungkap berbagai fenomena yang menggambarkan serangkaian kegiatan dakwah kultural Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang. Sehingga dapat diperoleh sejumlah informasi mengenai berbagai upaya penerapan program yang dimaksud. Penelitian ini dapat disimpulkan, pertama kontribusi Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang terhadap perkembangan metode dakwah kultural adalah dakwah melalui seni. Kedua, Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang sebagai tempat Wisata Religi yang sangat signifikan.   This research tries to reveal the various phenomenon that describe a series of cultural propaganda activities Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang. In order to obtain some informations about the efforts of the implementation of the program in question. It can be concluded, the first contribution of Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang on the development of methods of cultural propaganda is propaganda through art. Second Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang as a very significant Religious Tourism.

  17. Optical phonon scattering on electronic mobility in Al2O3/AlGaN/AlN/GaN heterostructures

    Science.gov (United States)

    Zhou, X. J.; Qu, Y.; Ban, S. L.; Wang, Z. P.

    2017-12-01

    Considering the built-in electric fields and the two-mode property of transverse optical phonons in AlGaN material, the electronic eigen-energies and wave functions are obtained by solving Schrödinger equation with the finite difference method. The dispersion relations and potentials of the optical phonons are given by the transfer matrix method. The mobility of the two dimensional electron gas influenced by the optical phonons in Al2O3/AlGaN/AlN/GaN heterostructures is investigated based on the theory of Lei-Ting force balance equation. It is found that the scattering from the half-space phonons is the main factor affecting the electronic mobility, and the influence of the other phonons can be ignored. The results show that the mobility decreases with increasing the thicknesses of Al2O3 and AlN layers, but there is no definite relationship between the mobility and the thickness of AlGaN barrier. The mobility is obviously reduced by increasing Al component in AlGaN crystal to show that the effect of ternary mixed crystals is important. It is also found that the mobility increases first and then decreases as the increment of the fixed charges, but decreases always with increasing temperature. The heterostructures constructed here can be good candidates as metal-oxide-semiconductor high-electron-mobility-transistors since they have higher electronic mobility due to the influence from interface phonons weakened by the AlN interlayer.

  18. Al2O3 adherence on CoCrAl alloys

    International Nuclear Information System (INIS)

    Kingsley, L.M.

    1980-04-01

    Adherence of protective oxides on NiCrAl and CoCrAl superalloys has been promoted by a dispersion of a highly oxygen reactive element or its oxide being produced within the protection system. Two aspects of this subject are investigated here: the use of Al 2 O 3 as both the dispersion and protective oxide; and the production of an HfO 2 dispersion while simultaneously aluminizing the alloy. It was found that an Al 2 O 3 dispersion will act to promote the adherence of an external scale of Al 2 O 3 to a degree comparable to previously tested dispersions and an HfO 2 dispersion comparable to that produced by a Rhines pack treatment is produced during aluminization

  19. Tracing Al Shabaab’s Decision to Cooperate with Al Qaeda in Somalia (2008

    Directory of Open Access Journals (Sweden)

    Adlini Ilma Ghaisany Sjah

    2014-02-01

    Full Text Available 'Al Shabaab, a Somali insurgent with predominantly nationalistic causes (alongside transnational [global Jihad] and Islamic goals made the choice to fight on behalf of Al Qaeda in 2008. The decision to do so contrasted with Al Shabaab’s previous behaviour of actively denying cooperation and distancing itself from Al Qaeda. This study aims to uncover factors that contributed to Al Shabaab’s decision through the use of process-tracing. The results show that Al Shabaab’s declaration of cooperation with Al Qaeda in August 2008 was brought about by a series of events that traced back to four factors: public reactions to the implementation of a Salafi ideology, the shift to a radical leadership, Al Shabaab’s inability to maintain stability in areas under its control and its increasing attacks by Al Shabaab on the Somali public. Al Shabaab pursued cooperation with Al Qaeda after realizing that their nationalistic preference was no longer achievable in the near future.' ' '

  20. Controlling applied to information processing: quality management applied to IP projects and IP services; Informationsverarbeitungs-Controlling: Qualitaetsmanagement fuer IV-Projekte und fuer IV-Service

    Energy Technology Data Exchange (ETDEWEB)

    Becker, B. [Vereinigung Deutscher Elektrizitaetswerke e.V. (VDEW), Frankfurt am Main (Germany); Beckers, F. [Isar-Amperwerke AG, Muenchen (Germany); Dewald, N. [Bayernwerk AG, Muenchen (Germany); Hauffe, P. [Pfalzwerke AG, Ludwigshafen am Rhein (Germany); Hein, F. [EVS AG Stuttgart (Germany); Hoederath, M. [Vereinigte Elektrizitaetswerke Westfalen AG (VEW), Dortmund (Germany); Seyen, R. [Staedtische Werke Nuernberg GmbH (Germany)

    1998-01-12

    The working group on information processing (IP) basics (in German: `IV-Grundlagen`) has prepared this contribution dealing with controlling applied to information processing. This new report, on the one hand, takes into consideration the role of the organizational IP unit as one offering its services to all sections of a company. On the other hand, information processing as an operational infrastructure influencing all business processes becomes increasingly important with respect to the competitiveness of the EVU. Therefore, quality management applied to IP projects and IP services must support this development. (orig./RHM) [Deutsch] Der VDEW Arbeitskreis `IV-Grundlagen` hat einen Beitrag zum Controlling fuer die Informationsverarbeitung erstellt. Hier geht zum einen die Rolle der Organisationseinheit IV als Dienstleister fuer alle Unternehmensbereiche ein. Zum anderen gewinnt die Informationsverarbeitung als betriebliche Infrastruktur fuer alle Geschaeftsprozesse zunehmende Bedeutung fuer die Wettbewerbsfaehigkeit der EVU. Das Qualitaetsmanagement fuer IV-Projekte und fuer IV-Service muss dies unterstuetzen. (orig./RHM)

  1. Warum will Charles Bovary kein Hausarzt mehr sein? – zur Medialität von Interviews mit angehenden Allgemeinmediziner_innen

    Directory of Open Access Journals (Sweden)

    Niklas Barth

    2016-07-01

    Full Text Available Im Zentrum dieses Beitrags stehen Interviews mit Ärzt_innen in Weiterbildung (ÄiW zum Facharzt/zur Fachärztin für Allgemeinmedizin. Aus der Analyse dieser Texte kann man erstens lernen, wie sich Motive überhaupt als plausible Motive darstellen lassen. Dabei sieht man zweitens, dass die Kommunikation von Kontingenz in diesen Erzählungen geradezu als Ressource benutzt wird, die Kontingenz einer zu erzählenden Geschichte zu bewältigen. Vor allem aber gerät drittens in den Interviews die Medialität des Forschungsprozesses selbst in den Blick. In der selektiven Form dieser Erzählungen liegt selbst schon ihr Befund. Eine Soziologie, die die Erzählungen ihrer Informant_innen fast trotzig für Krücken hält, um zum Leben selbst durchzustoßen, kann von diesem medientheoretischen Hinweis womöglich profitieren. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs160317

  2. Decision-Making and Sources of Evidence in Occupational Therapy and Other Health Professions. Evidence-Informed Practice / Entscheidungsfindung und Evidenzquellen in der Ergotherapie und weiteren Gesundheitsberufen. Evidenzinformierte Praxis

    Directory of Open Access Journals (Sweden)

    Tomlin George S.

    2014-12-01

    Full Text Available Von den Gesundheitsberufen wird einerseits verlangt, dass jeder einzelne Praktiker wissenschaftsbasiert arbeitet, d.h. publizierte Evidenz in der Praxis anwendet (Evidence Based Practice, EBP. Andererseits müssen sie als Profession valide Evidenz der Ergebnisse ihres professionellen Handelns produzieren. Diese zwei Dimensionen von EBP werden in der Diskussion oft nicht auseinander gehalten, was zu Verwirrung führt. Dieser theoretische Beitrag differenziert diese beiden Prozesse als “Evidence- Supported Practice” und “Evidence-Informed Practice” und zeigt, wie sie wieder zusammengeführt werden können. Zur Bewertung der externen und internen Validität von externer Evidenz wird die Forschungspyramide verwendet. In der Alltagspraxis müssen externe und interne Evidenzarten verwendet werden. Um den Begriff der internen Evidenz zu erklären, werden Beispiele aus der Ergotherapie und aus der Literatur anderer Gesundheitsberufe herangezogen. Empfehlungen für eine umfassende Strategie Evidenz-Basierter Praxis, adressiert an Praktiker, Forscher, und Lehrer werden formuliert.

  3. Recycling-friendly planning and construction; Recyclinggerechtes Planen und Bauen

    Energy Technology Data Exchange (ETDEWEB)

    Willkomm, W. [Hannover Univ. (Germany). Fachbereich Architektur]|[Institut fuer Industrialisierung des Bauens GmbH, Hannover (Germany)

    1995-09-01

    Building materials recycling is part and parcel of any intelligent, resource-conserving materials recycling concept. Principally, however, it can never be more than the second best solution. This is because it must always come after all has been done to prevent building material residues from arising in the first place. The greatest potential for waste avoidance in the building industry lies in the planning phase. Planning nowadays is oriented more to production, utilisation, reutilisation, maintenance, and recycling processes, i.e. more to processes in general than to the design of any certain product. (orig./HW) [Deutsch] Baustoff-Recycling ist ein unverzichtbarer Beitrag zu intelligenten, resourcensparenden Materialkreislaeufen. Es stellt aber immer nur die zweitbeste Loesung dar. Denn zunaechst muessen alle Moeglichkeiten genutzt werden. Bauabfaelle gar nicht erst entstehen zu lassen. Die groessten Potentiale zur Abfallvermeidung in der Bauproduktion liegen in einer Bauplanung, die sich intensiver als bisher an Herstellungs-, Nutzungs-, Umnutzungs-, Instandhaltungs- und Recyclingprozessen orientiert, also eher prozessorientierte Planung als Produktgestaltung. (orig./HW)

  4. Stochastic modelling of the thermal characteristics of a hot-water storage tank on the basis of Markov chains; Zur stochastischen Modellierung des thermischen Verhaltens eines Warmwasserspeichers mittels Markov`scher Ketten

    Energy Technology Data Exchange (ETDEWEB)

    Werner, U.J. [Bauhaus-Universitaet Weimar (Germany). Fakultaet Bauingenieurwesen

    1998-09-01

    In an earlier contribution, a stochastic model was presented for a hot water storage tank supplied by a solar collector. The model was characterized in that the storage tank was assumed to be an ideal stratified storage tank, and its volume was subdivided into discrete identical storage compartments, so-called states, on the basis of the energy withdrawn from the tank. This simple model is now extended by assuming a stochastic variable for energy withdrawal and by taking account of energy loss at the surface of the hot water storage tank and inside it. [Deutsch] In einem frueheren Beitrag war fuer einen thermischen Speicher, der von einem Sonnenkollektor gespeist wird, ein stochastisches mathematisches Modell derart aufgestellt worden, dass ein als idealer Schichtenspeicher konzipierter Warmwasserspeicher bezueglich seines Volumens in diskrete, an der Energieentnahme orientierte, gleiche Speichereinheiten, sogenannte Zustaende, unterteilt wurde. Das einfache Modell wird nunmehr erweitert, indem die Entnahme als eine stochastische Groesse angenommen wird und die Energieverluste am und im Warmwasserspeicher Beruecksichtigung finden. (orig.)

  5. Gerechtigkeit, ethische Subjektivität und Alterität. Zu den normativen Implikationen der Philosophie von Emmanuel Levinas

    Directory of Open Access Journals (Sweden)

    Seitz Sergej

    2016-07-01

    Full Text Available Obwohl seit einiger Zeit ein verstärktes Forschungsinteresse an Emmanuel Levinas’ Denken des Politischen, verbunden mit einer genaueren Inblicknahme der zentralen Begriffe des Dritten und der Gerechtigkeit aufgekommen ist, blieb bislang unklar, inwiefern aus Levinas’ intrinsisch ‚ethischem‘ Denken in konkreterer Weise normative Konsequenzen zu ziehen sind. Diesem Desiderat versucht der vorliegende Beitrag nachzukommen. Das Levinas’sche Gerechtigkeitsdenken wird dabei so eingeführt, dass es zugleich als alternativer Entwurf und als produktive kritische Provokation für gegenwärtige Gerechtigkeitstheorien lesbar wird. Ausgehend von einer Rekonstruktion des alteritären Verständnisses ethischer Subjektivität, wie es Levinas insbesondere in Jenseits des Seins erarbeitet, wird ausgelotet, wie tragfähig Levinas’ ethische Konzeption plural alteritär durchfurchter Subjektivität für normative Gerechtigkeitsfragen ist. Aus einer Reflexion auf den Begriff des ‚Dritten‘ werden einige konkrete Konsequenzen für das Denken gerechter Institutionen gezogen.

  6. All About ALS

    Science.gov (United States)

    ... Subscribe August 2015 Print this issue All About ALS Understanding a Devastating Disorder En español Send us ... Sports Concussions Wise Choices How Can I Help ALS Research? If you have ALS, join the National ...

  7. Atomistic simulations of diffusion mechanisms in off-stoichiometric Al-rich Ni3Al

    International Nuclear Information System (INIS)

    Duan, Jinsong

    2007-01-01

    This paper presents dynamics simulation results of diffusion in off-stoichiometric Al-rich Ni 3 Al (Ni 73 Al 27 ) at temperature ranging from 1300 to 1550 K. The interatomic forces are described by the Finnis-Sinclair type N-body potentials. Particular attention is devoted to the effect of the extra 2% of Al atoms sitting on the Ni sublattice as antisite point defects (Al Ni ) on diffusion. Simulation results show that Ni atoms mainly diffuse through the Ni sublattice at the temperatures investigated. Al atoms diffuse via both the intrasublattice and antistructure bridge (ASB) mechanisms. The contribution to Al diffusion from the ASB mechanism decreases at the lower temperature (T Ni ) enhances both Al and Ni diffusion in Ni 73 Al 27 . The Ni-Al coupled diffusion effect is observed and understood at the atomic level for the first time

  8. Methodology and Characteristics of Zad al-masir fi ‘ilm al-tafsirby AllamaIbn al-Jawzī (Urdu

    Directory of Open Access Journals (Sweden)

    Dr. Muhammad Riaz al Azhari

    2017-01-01

    Full Text Available This article describes the methodology and characteristics of Zad al-masir fi ‘ilm al-tafsir. This is one the finest work of AllamaIbn al-Jawzī, a 6th century prominent Interpreter. Several editions of this Tafsir have been published. However, the edition of dar al-kitab al-‘arbi, Beirut published in four volumes is selected for this study. This exegesis is based on conventional narrations, authentic quotations from the Islamic Scholars and lingual & grammatical discussions. As a witness, causes of verses (asbabal-Nuz┴l,Makki and MadaniSurah’s (chapters, the abrogating and abrogated verses (al-nasikhwal-mans┴kh and Islamic jurisprudence have been discussed in it where needed. The quality of this translation which is admirable is that mostly authentic Ahadith from original sources, and references to well known basic books in relevant discussions have been described. `

  9. Phenotypic and genotypic studies of ALS cases in ALS-SMA families.

    Science.gov (United States)

    Corcia, Philippe; Vourc'h, Patrick; Blasco, Helene; Couratier, Philippe; Dangoumau, Audrey; Bellance, Remi; Desnuelle, Claude; Viader, Fausto; Pautot, Vivien; Millecamps, Stephanie; Bakkouche, Salah; Salachas, FranÇois; Andres, Christian R; Meininger, Vincent; Camu, William

    2018-03-01

    Amyotrophic lateral sclerosis (ALS) and spinal muscular atrophy (SMA) are the most frequent motor neuron disorders in adulthood and infancy, respectively. There is a growing literature supporting common pathophysiological patterns between those disorders. One important clinical issue for that is the co-occurrence of both diseases within a family. To collect families in which ALS and SMA patients co-exist and describe the phenotype and the genotype of ALS patients. Nine families with co-occurrence of SMA and ALS have been gathered over the last 15 years. Epidemiological, phenotype and genetic status were collected. Out of the nine families, six corresponded to the criteria of familial ALS (FALS). Clinical data were available for 11 patients out of the 15 ALS cases. Mean age of onset was 58.5 years, site of onset was lower limbs in nine cases (81.8%), median duration was 22 months. Four ALS patients carried a mutation: three mutations in SOD1 gene (G147N in two cases and one with E121G) and one repeat expansion in the C9ORF72 gene. Three patients had abnormal SMN1 copy numbers. While the high proportion of familial history of ALS cases in these ALS-SMA pedigrees could have suggested that these familial clusters of the two most frequent MND rely on a genetic background, we failed to exclude that this occurred by chance.

  10. Eutectic microstructures of Al-ThA13 and Al-UA14 alloys

    International Nuclear Information System (INIS)

    Vieira, R.R.; Ambrozio Filho, F.

    1990-01-01

    This paper deals on the microstructures of systems Al-ThAl3 and Al-UAL4, which are composed by a non faceted phase (aluminium) and an intermetallic phase (ThAl3 or UAL4) which is normally faceted phase. (C.M.)

  11. Thinking Beyond the Categories: On the Diasporisation of Gender Studies

    Directory of Open Access Journals (Sweden)

    Stefanie Kron

    2013-01-01

    Full Text Available In diesem Beitrag wird das Potential des Konzepts „Diaspora“ für eine feministische Methodologie diskutiert. Die Überlegungen gehen von der Beobachtung aus, dass die Mehrheit der Geschlechter- und Intersektionalitätsforschung in Deutschland innerhalb eines nationalen Rahmens arbeitet. Entsprechend fehlt ihr das Bewusstsein von den globalen Verknüpfungen und der konstitutiven Bedeutung von Migration für die europäischen Gesellschaften seit den Zeiten von Kolonisation und Sklavenhandel. Es gibt deshalb innerhalb der Geschlechterforschung eine Tendenz, Differenzen zu essentialisieren, obwohl das erklärte Ziel die Analyse sozialer Ungleichheiten ist. Nach einem kursorischen Überblickt über die Konzepte, die Gesellschaft aus der Perspektive der Bewegung und Diasporisierung betrachten – wie Édouard Glissant’s ‚créolisation‘, Paul Gilroy’s ‚black Atlantic‘ ebenso wie Peter Linebaugh’s und Markus Rediker’s ‚red Atlantic‘ – werden in diesem Artikel drei feministische Ansätze aus den 1980er und 1990er Jahren wieder aufgegriffen, die Elemente von dem, was als diasporische feministische Methode bezeichnet werden kann, enthalten: Es handelt sich um Angela Davis’ analytische Methode der Perspektivität, Avtar Brahs Auffassung vom ‚diaspora space‘ und Gloria Anzaldúas ‚border thinking‘. Im letzten Abschnitt des Beitrags wird gezeigt, wie diese konzeptionellen Instrumente zu einem besseren Verständnis interdependenter und globalisierter sozialer Ungleichheiten beitragen, indem sie Gender- und Intersektionalitätsstudien um die Diaspora-Perspektive erweitern.

  12. Interface reactions in the Al-Si-SiC and Mg-Al-Al{sub 2}O{sub 3} composite systems

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, P.K. [Commission of the European Communities, Petten (Netherlands). Inst. for Advanced Materials; Fazal-Ur-Rehman [Imperial Coll. of Science, Technology and Medicine, London (United Kingdom). Dept. of Materials; Fox, S. [Imperial Coll. of Science, Technology and Medicine, London (United Kingdom). Dept. of Materials; Flower, H.M. [Imperial Coll. of Science, Technology and Medicine, London (United Kingdom). Dept. of Materials; West, D.R.F.

    1995-12-31

    Structural and compositional observations are reported on the influence of the interfaces on the mechanisms and kinetics of liquid metal-ceramic reactions in Al-SiC, Al-Si-SiC, Mg-Al{sub 2}O{sub 3} and Mg-Al-Al{sub 2}O{sub 3} composites. The aluminium based materials contained up to 20 vol% SiC in particulate form, and were produced by a spray casting process; subsequently the interface reactions were studied in samples heated to temperatures up to 1100 C. The reaction product was Al{sub 4}C{sub 3} in both Al-SiC and Al-Si-SiC composites. The influence of the crystallography and topology of the SiC particle surfaces on the nucleation of the Al{sub 4}C{sub 3} has been demonstrated; surface asperities play an important role. Growth of nuclei proceeds to form continuous reaction product layers which control the subsequent kinetics. The magnesium based composites contained 5 vol% Al{sub 2}O{sub 3} fibres (3 {mu}m in diameter), and were produced by a liquid infiltration process. SD Safimax fibres with relatively low and high porosity, and also RF Saffil fibres, with a silica binder, were investigated. Fibre porosity plays a major role in accelerating the penetration of Mg into the fibres with reaction to form MgO. Silica binder on the fibre surface transforms to MgO. The reaction rate was reduced by the presence of aluminium in the matrix. The factors controlling the reactions in the aluminium and magnesium based composites are compared. (orig.)

  13. KONSTRUKSI FIQH BUKHARI DALAM KITAB AL-JAMI’ AL-SHAHIH

    Directory of Open Access Journals (Sweden)

    Abdul Sattar

    2011-06-01

    Popularitas Imam Bukhari sebagai penyusun kitab Hadits memiliki posisi yang tinggi di kalangan masyarakat muslim. Kitab Al-Jami ‘al-Shahih karya Imam  Bukhari dianggap sebagai koleksi hadits terbaik setelah Quran. Namun, tidak ada banyak informasi tentang kemampuannya di bidang Hukum Islam (fiqh. Ada beberapa pertanyaan yang dapat diajukan dalam hal tersebut;  pertama, apakah pemikiran Imam Bukhari dipengaruh salah satu dari empat fuqaha Sunni saat menulis al-Jami ‘al-Shahih?. Kedua, apa yang diupayakan Imam Bukhari untuk mengartikulasikan pemikirannya tentang hukum Islam? Dengan menggunakan pendekatan eksploratif, verifikatif dan hermenetical, artikel ini akan mengungkapkan bahwa Imam Bukhari tidak berada di bawah pengaruh madhab tertentu dalam mengartikulasikan pemikirannya tentang hukum Islam. Dia mengartikulasikan pandangannya dengan cara yang unik dan execelent berdasarkan kapasitasnya sebagai muhaddits.

  14. La "historia de los omeyas de al-Andalus" en los Masalik al-Absar

    OpenAIRE

    Molina, Luis

    2005-01-01

    [ES]Los Masalik al-absar de Ibn Fadl Allah al-`Umari incluyen un breve resumen de la Historia de los omeyas de al-Andalus. En este trabajo se analizan las relaciones textuales entre ese pasaje y el Muqtabis de Ibn Hayyan, crónica que resulta ser la fuente casi única utilizada por al-`Umari para redactar ese capítulo. [EN]The Masalik al-absar by Ibn Fadl Allah al-`Umari contains a brief summary of the Umayyad history in al-Andalus. In this article, the textual relationship between this p...

  15. Cryptanalysis of Lin et al.'s Efficient Block-Cipher-Based Hash Function

    NARCIS (Netherlands)

    Liu, Bozhong; Gong, Zheng; Chen, Xiaohong; Qiu, Weidong; Zheng, Dong

    2010-01-01

    Hash functions are widely used in authentication. In this paper, the security of Lin et al.'s efficient block-cipher-based hash function is reviewed. By using Joux's multicollisions and Kelsey et al.'s expandable message techniques, we find the scheme is vulnerable to collision, preimage and second

  16. From Kitāb al-ḥadā’iq to Kitāb al-dawā’ir: Reconsidering Ibn al-Sīd al-Batalyawsī’s Philosophical Treatise

    Directory of Open Access Journals (Sweden)

    Eliyahu, Ayala

    2015-06-01

    Full Text Available The philosophical treatise known as Kitāb al-ḥadā’iq is generally ascribed to the 12th century Andalusian author Ibn al-Sīd al-Batalyawsī, although this attribution is sometimes contested. This paper offers a new interpretation of the title, textual history, authorship, sources, and literary genre of this treatise, on the basis of new textual evidence, a reexamination of known evidence, and a comparison between the treatise and Batalyawsī’s works. The conclusions of this study are first, that Kitāb al-ḥadā’iq was not the treatise’s original title, and therefore it should be renamed Kitāb al-dawā’ir; second, that Kitāb al-dawā’ir was originally part of (one of the versions of Batalyawsī’s Kitāb al-masā’il; and third, that the textual and stylistic similarities between this treatise and Batalyawsī’s other works prove the authenticity of the treatise’s attribution to Batalyawsī. In addition, new findings regarding Batalyawsī’s use of formulas from the Rasā’il Ikhwān al-Safā, in Kitāb al-dawā’ir and Kitāb al-masā’il provide further evidence for the deep impact of the Ikhwān on Batalyawsī’s thought, as well as for the close connection between Kitāb al-dawā’ir and Kitāb al-masā’il. This connection is further highlighted according to the attribution of both treatises to the genre of questions and answers in Arabic literature. The evidence gathered in this paper supports the claim that Batalyawsī’s Kitāb al-dawā’ir should be seen as an integral part of his literary oeuvre, as well as of Andalusian philosophical literature in general.Generalmente el tratado filosófico conocido como Kitāb al-ḥadā’iq se asocia al autor andalusí del siglo XII Ibn al-Sid al-Batalyawsī, aunque esta atribución ha sido discutida en ocasiones. Este artículo ofrece una nueva interpretación del título, la historia del texto, la autoría, las fuentes e incluso del género literario al que se

  17. Theory and X-ray Absorption Spectroscopy for Aluminum Coordination Complexes – Al K-Edge Studies of Charge and Bonding in (BDI)Al, (BDI)AlR2, and (BDI)AlX2 Complexes.

    Science.gov (United States)

    Altman, Alison B; Pemmaraju, C D; Camp, Clément; Arnold, John; Minasian, Stefan G; Prendergast, David; Shuh, David K; Tyliszczak, Tolek

    2015-08-19

    Polarized aluminum K-edge X-ray absorption near edge structure (XANES) spectroscopy and first-principles calculations were used to probe electronic structure in a series of (BDI)Al, (BDI)AlX2, and (BDI)AlR2 coordination compounds (X = F, Cl, I; R = H, Me; BDI = 2,6-diisopropylphenyl-β-diketiminate). Spectral interpretations were guided by examination of the calculated transition energies and polarization-dependent oscillator strengths, which agreed well with the XANES spectroscopy measurements. Pre-edge features were assigned to transitions associated with the Al 3p orbitals involved in metal-ligand bonding. Qualitative trends in Al 1s core energy and valence orbital occupation were established through a systematic comparison of excited states derived from Al 3p orbitals with similar symmetries in a molecular orbital framework. These trends suggested that the higher transition energies observed for (BDI)AlX2 systems with more electronegative X(1-) ligands could be ascribed to a decrease in electron density around the aluminum atom, which causes an increase in the attractive potential of the Al nucleus and concomitant increase in the binding energy of the Al 1s core orbitals. For (BDI)Al and (BDI)AlH2 the experimental Al K-edge XANES spectra and spectra calculated using the eXcited electron and Core-Hole (XCH) approach had nearly identical energies for transitions to final state orbitals of similar composition and symmetry. These results implied that the charge distributions about the aluminum atoms in (BDI)Al and (BDI)AlH2 are similar relative to the (BDI)AlX2 and (BDI)AlMe2 compounds, despite having different formal oxidation states of +1 and +3, respectively. However, (BDI)Al was unique in that it exhibited a low-energy feature that was attributed to transitions into a low-lying p-orbital of b1 symmetry that is localized on Al and orthogonal to the (BDI)Al plane. The presence of this low-energy unoccupied molecular orbital on electron-rich (BDI)Al distinguishes

  18. Alexander von Humboldt und Carl Friedrich Gauß als Wegbereiter der neuen Disziplin Erdmagnetismus

    Directory of Open Access Journals (Sweden)

    Karin Reich

    2011-03-01

    Full Text Available AbstractThough Alexander von Humboldt was motivated for the first time to deal with earthmagnetism during his stay in Freiberg, it was in France that he really became a specialist in this respect. During most of his journeys he made earthmagnetic measurements. His collaboration with Arago was of great importance, it was in Paris that the first magnetic observatory was built. Humboldt rendered outstanding services to the investigation of earth magnetism by two major achievements: 1. He emphasized intensity measurements and 2. he put forward the law that the magnetic intensity is increasing from the magnetic equator toward the magnetic poles. At least since 1803 Carl Friedrich Gauss was interested in earthmagnetism and especially in Humboldt’s early published data. That Wilhelm Weber became professor of physics at the University of Göttingen in 1831 was a turning point for Gauss. In 1833 Göttingen was the centre of investigating earthmagnetism, a new era began which lasted only until 1843. Gauss’ main contributions were more or less theoretical, in 1832/3 he transformed Humboldt’s relative intensity measurements into absolute ones which were independent of the instrument’s needle. A new epoch began with Gauss’ publication „Allgemeine Theorie des Erdmagnetismus” (1839. The main point was the newly defined notion of „potential“. Gauss was the first to present the surface of the earth with equipotential lines. ZusammenfassungAlexander von Humboldt hatte sich bereits in Freiberg mit dem Erdmagnetismus beschäftigt; jedoch erst in Frankreich lernte er die entsprechenden Beobachtungsmethoden kennen. Auf allen seinen Reisen machte er erdmagnetische Messungen. Seine Zusammenarbeit mit Arago in Paris war besonders fruchtbar, hier wurde das erste magnetische Observatorium gebaut. Humboldt beschäftigte sich vor allem mit Intensitätsmessungen; sein wichtigster Beitrag war die Feststellung, dass die magnetische Intensität vom

  19. Modelling of suspended matter transport and turnover in biofilters for waste water treatment; Modellierung von Stofftransport und -umsatz in Biofiltern zur Abwasserreinigung

    Energy Technology Data Exchange (ETDEWEB)

    Telgmann, U. [Kassel Univ. (Gesamthochschule) (Germany). Fachgebiet Siedlungswasserwirtschaft; Horn, H. [Fachhochschule Magdeburg (Germany). Hydro- und Abfallchemie

    1999-07-01

    Essential elements of the presented model for biofilters are suspended matter transfer in the boundary layer water/biofilm, the gradient of concentration for substrate turnover in the biofilm with limited diffusion, and the gradient of concentration and biomass distribution both in the biofilm and over the height of the reactor. Problematic in biofilm modelling is linking the turnover of substrate in the biofilm affixed to the carrier material with changes in concentration along the reactor height. This means that concentration profiles need to be calculated both in the biofilm and over the height of the reactor. The presented model describes substrate turnover in the biofilm by means of a Monod kinetics, and diffusive suspended matter transport with the aid of Fick's second law. The change in concentration over the filter bed height is taken into account by dividing the reactor volume into five complete-mixing segments. Further elements of modelling are biomass production and the corresponding discharge from the biofilter. In exemplary manner, a biofilter for downstream denitrification with methanol was modelled and the results were compared with measurements taken at a semi-technical pilot plant. (orig.) [German] Wesentliche Elemente des hier vorgestellten Modells fuer Biofilter sind der Stoffuebergang in der Grenzschicht Wasser/Biofilm, der Konzentrationsgradient beim diffusionslimitierten Substratumsatz im Biofilm, der Konzentrationsgradient und die Biomasseverteilung sowohl im Biofilm als auch ueber die Reaktorhoehe. Problematik bei der Modellierung eines Biofilms ist die Verknuepfung von Substratumsatz in dem auf dem Traegermaterial haftenden Biofilm mit der Konzentrationsveraenderung entlang der Reaktorhoehe. Die Konzentrationsprofile muessen also sowohl im Biofilm als auch ueber die Reaktorhoehe berechnet werden. Im praesentierten Modell wird der Substratumsatz im Biofilm mit einer Monodkinetik und der diffusive Stofftransport mit Hilfe des 2. Fick

  20. Thermodynamic properties of Al-Mn, Al-Cu, and Al-Fe-Cu melts and their relations to liquid and quasicrystal structure

    International Nuclear Information System (INIS)

    Zaitsev, A I; Zaitseva, N E; Shimko, R Yu; Arutyunyan, N A; Dunaev, S F; Kraposhin, V S; Lam, Ha Thanh

    2008-01-01

    Thermodynamic properties of molten Al-Mn, Al-Cu and Al-Fe-Cu alloys in a wide temperature range of 1123-1878 K and the whole range of concentrations have been studied using the integral effusion method and Knudsen mass spectrometry. Thermodynamic functions of melts were described by the associated solution model. The possibility of icosahedral quasicrystal (i-QC) precipitation from liquid Al-Mn and Al-Cu-Fe alloys was found to be a consequence of the existence in liquid associates (clusters). A geometric model is suggested for the structure of associates in liquid

  1. Sintering Behavior of CNT Reinforced Al6061 and Al2124 Nanocomposites

    Directory of Open Access Journals (Sweden)

    Nouari Saheb

    2014-01-01

    Full Text Available Ball milling and spark plasma sintering were successfully used to produce carbon nanotube reinforced Al6061 and Al2124 nanocomposites which have potential applications in the fields of aerospace, automotive, electronics, and high precision instrumentation. Al2124 and Al6061 nanocomposite powders containing 0.5 to 2 wt.% CNTs prepared through sonication and wet ball milling were spark plasma sintered at 400, 450, and 500°C for 20 minutes under a pressure of 35 MPa. CNTs were better dispersed, and less agglomerated and had good adhesion to the matrix in composites containing 1 wt.% CNTs. The increase of CNT content to 2 wt.% led to the formation of CNT clusters which resulted in less uniform and homogenous composite powders. Almost full densification of Al6061 reinforced with CNTs was achieved at 500°C. Also, CNTs reinforced Al2124 nanocomposites reached very high densities at 500°C. Composites reinforced with 1 wt.% CNTs displayed better densification compared to composites containing 2 wt.% CNTs. The increase of CNTs content from 0.5 to 1 wt.% increased the hardness of the Al6061 and Al2124 alloys to maximum values. Further increase of CNTs content to 2 wt.% decreased the hardness to values lower than that of the monolithic alloys.

  2. Tetragonal phase in Al-rich region of U-Fe-Al system

    International Nuclear Information System (INIS)

    Meshi, L.; Zenou, V.; Ezersky, V.; Munitz, A.; Talianker, M.

    2005-01-01

    A new ternary aluminide U 2 FeAl 20 with the approximate composition Al-4.2at% Fe-8.5at% U was observed in the Al-rich corner of the U-Al-Fe system. Transmission electron microscopy and electron microdiffraction technique were used for characterization of the structure of this phase. It has a tetragonal unit cell with the parameters a=12.4A and c=10.3A and can be described by the space group I4-bar 2m

  3. Ilhaq al-Masa'il bi Nazairiha dan Penerapannya dalam Bahth al-Masa'il

    Directory of Open Access Journals (Sweden)

    Luthfi Hadi Aminuddin

    2013-11-01

    Full Text Available Abstract: Ilh}a>q al-Masa>’il bi Naz}a>iriha is one of the methods used by Nahdlatul Ulama in resisting the opinion based on (manhaji analytical concept of Islamic jurisprudence (the solution for complex social problems as the main purpose of Islamic shari’ah. As known that, up to now, ilh}a>q has been understood as a process of answering a new case by the way of equating to the old one which is written in the book called al-mu’tabarah. Such ilh}a>q has got many criticisms both from the definitions, procedures and its epistemogical footing. This paper is about to reveal how the NU clerics of Islam understand the concept of Ilh}a>q}, what its epistemological footing was and how the concept was applied in discussing many cases (bah}th al-masa>’il. Based on the writer’s study to several documents of decision results of NU that Ilh}a>q did not only simplify to equate the new cases with the old ones that have been freely discussed in the books of al-mu’tabarah, but both cases should have similar legal substance, that is, both should be under the decrees of laws of al-qawa> ‘id al-fiqhi>yah. Thus, Ilh}a>q is actually answering the problem by applying al-qawa>‘id al-fiqhi>yah, whereas the formulation al-qawa>‘id al-fiqhi>yah itself was set off from the examination of a number of furu>’ generated by qiya> s. This paper also found three variations of the implementation of Ilh}a>q in bah}th al-masa>’il. First, the application of Ilh}a>q was without mentioning al-qawa> ‘id al-fiqhi>yah which covered new cases (mulh}aq and the old case law that has been known in the books of fiqh (mulh}aq bih/attached to. Second, the application of Ilh}a>q was accompanied by mentioning mulh}aq bih and al-qawa> ‘id al-fiqhi>yah. Third, the application of Ilh}a>q, was only by the mentioning al-qawa> ‘id al-fiqhi>yah.

  4. Nanoindentation studies of ex situ AlN/Al metal matrix nanocomposites

    International Nuclear Information System (INIS)

    Fale, Sandeep; Likhite, Ajay; Bhatt, Jatin

    2014-01-01

    Highlights: • Formation of in-situ phases nucleated on AlN particles strengthens the matrix. • Formation of in-situ phases increases with AlN content in nanocomposites. • Stronger in-situ phases results in increased hardness and modulus of elasticity. - Abstract: Nanocrystalline Aluminium nitride (AlN) powder is dispersed in different weight ratio in Aluminum matrix to fabricate metal matrix nanocomposite (MMNC) using ex situ melt metallurgy process. The synthesized Al–AlN nanocomposites are studied for phase analysis using high resolution scanning electron microscopy (FEG-SEM) and for hardness behavior using microindentation and nanoindentation tests. Quantitative analysis of the oxide phases is calculated from thermodynamic data and mass balance equation using elemental data obtained from energy dispersive spectroscopy (EDS) results. Role of oxide phases in association with AlN particles is investigated to understand the mechanical behavior of composites using nanoindentation tester. Load–displacement profile obtained from nanoindentation test reveals distribution of oxide phases along with AlN particle and their effect on indent penetration

  5. Wenn ich nur wüsste, ob…: Der beamtenrechtliche Aufstieg im deutschen Bibliothekswesen am Beispiel des Freistaates Bayern

    Directory of Open Access Journals (Sweden)

    Kathrin Schwärzel

    2015-12-01

    Full Text Available Mit dem Gesetz zum Neuen Dienstrecht in Bayern hat der bayerische Gesetzgeber im Jahre 2010 das Laufbahnrecht grundlegend reformiert. Als Kernstück der Reform gilt der Regelungskomplex zum beamtenrechtlichen Aufstieg, insbesondere zur sogenannten modularen Qualifizierung, mit dem der Landesgesetzgeber einen modernen Weg im Personalmanagement einschlägt. Der Beitrag ordnet die Regelungen in ihren laufbahnrechtlichen Kontext ein und stellt das neue Instrument der Personalentwicklung näher vor. In 2010, the Bavarian legislator introduced a fundamental public employment law reform. Emphasis was put on professional advancement through modular training as a new approach to human resource management in public administration. This article takes a closer look at this new personnel development instrument and its regulation.

  6. Zur Politik der Intertextualität in Roberto Bolaños ‚Estrella Distante‘

    Directory of Open Access Journals (Sweden)

    Samir Sellami

    2014-12-01

    Full Text Available Am Beispiel von Bolaños 1996 erschienenem Kurzroman Estrella Distante untersucht der Beitrag die spezifische Logik der Intertextualität in Bolaños Poetik. Seine implizite Logik der Intertextualität entwickelt sich dabei nicht im luftleeren Raum, sondern im Kontrastverhältnis zu der erzählten Poetik des Protagonisten Carlos Wieder. Dessen formal progressive, aber politisch reaktionär motivierte Poetik deckt die fundamentale Ambivalenz avantgardistischer Poetiken auf und führt zur gegensätzlichen Affirmation einer metabolischen Intertextualität, die den körperlichen und gelebten Kontakt mit dem Literarischen in den Vordergrund stellt. In dieser Konstellation wird Estrella Distante lesbar als poetischer Widerstand und literarische Vergeltung an der historischen Wirklichkeit.

  7. Medienethik: Werte neu denken. – Gibt es Massstäbe im Informationszeitalter?

    Directory of Open Access Journals (Sweden)

    Claudia de Witt

    2001-05-01

    Full Text Available Im Übergang von der Informations- zur Wissensgesellschaft erweist sich die Frage nach pädagogischen Massstäben als besonders relevant. Zwar entstehen mit der Entwicklung zur Globalisierung durch die neuen Medien neue Handlungsmöglichkeiten, zugleich aber auch Pluralität und Unübersichtlichkeit bei den Wertorientierungen. Eine Auseinandersetzung mit medienethischen Fragen muss deshalb auf Überlegungen zielen, Werte neu zu denken. Die fogenden Beiträge sind auf dem Hintergrund der Frühjahrstagung der Kommission Medienpädagogik 2001 in Mainz entstanden. In Form von Thesen haben sich die Autoren aus unterschiedlichen Perspektiven mit den ethischen Herausforderungen durch die alten und neuen Medien auseinandergesetzt. Auf diesem Hintergrund ist ein facettenreicher Beitrag zur Medienethik entstanden.

  8. Isothermal cross-sections of Sr-Al-Ge and Ba-Al-Ge systems at 673 K

    International Nuclear Information System (INIS)

    Kutsenok, N.L.; Yanson, T.I.

    1987-01-01

    X-ray and microstructural analyses are used to study phase equilibria in Sr-Al-Ge and Ba-Al-Ge systems. Existence of SrAl 2 Ge 2 , Sr(Al, Ge) 2 Ba(Al, Ge) 2 , Sr 3 Al 2 Ge 2 , Ba 3 Al 2 Ge 2 ternary compounds is confirmed, a new BaGe 4 binary compound and also new ternary compounds of approximate composition Sr 57 Al 30 Ge 13 and Ba 20 Al 40 Ge 40 , which crystal structure is unknown, are detected. Aluminium solubility in SrAl 4 and BaAl 4 binary compounds (0.05 atomic fraction) is determined. Ba(Al, Ge) 2 compound homogeneity region is defined more exactly (aluminium content varies from 0.27 to 0.51 at. fractions)

  9. Production of 26Al by spallation of Fe, Si, Al nuclei

    International Nuclear Information System (INIS)

    Paillard, P.

    1977-01-01

    Cross sections for 7 Be, 10 Be and 26 Al formation in Al, Si and Fe targets bombarded with 0.6 and 24GeV protons have been measured by using highly selective chemical separation and low level background counters. Results for 26 Al at 0.6GeV are in mb: 17.9 + or - 2.7 in Al, 12.5 + or - 2.5 in Si and 0.45 + or - 0.14 in Fe; at 24GeV 2.6 + or - 0.5mb in Fe. Results for 10 Be are not valid on account of experimental difficulties. It is deduced from these values of aluminium in cosmic ray propagation that 26 Al is not yet cosmic ray chronometer [fr

  10. 143 - 148_Makeri et al.

    African Journals Online (AJOL)

    USER

    2015-06-01

    Jun 1, 2015 ... Yuan et al., 2003), antimicrobial activity (Sundarrao et al., 1993; Betancur-Galvis et al., 1999; Takashi et al., 2006), anti-parasitic, anti-malarial activities (Alali et al., 1998; Jaramillo et al., 2000; Luna et al.,. 2005). This study evaluates the antibacterial activity of extract of stem –bark and leaf extracts of Annona.

  11. Phase relationships in the Al-rich region of the Al-Cu-Er system

    International Nuclear Information System (INIS)

    Zhang Ligang; Masset, Patrick J.; Cao Fuyong; Meng Fangui; Liu Libin; Jin Zhanpeng

    2011-01-01

    Research highlights: → One ternary phase τ 1 -Al 8 Cu 4 Er in Al-rich region with a composition of 59.4-60.4 at.% Al, 32.2-33.8 at.% Cu, and 6.4-7.7 at.% Er is observed in both as-cast and annealed alloys. At 673 K, the binary Al 3 Er phase dissolves about 3.51 at.% Cu. → The calculated solidification paths (based on the CALPHAD method) of as-cast alloys are in agreement with the experimental results. → It can be found that the resultant thermodynamic database can be applied to case studies of as-cast alloys, showing that the literature thermodynamic description of the Al-Cu-Er system is reliable as a working basis for computer-assisted alloy design. - Abstract: The Al-rich region of the ternary Al-Cu-Er system is investigated using the method of X-ray diffraction, scanning electron microscopy with energy dispersive X-ray spectroscopy. Phase equilibria in the Al-rich region of the Al-Cu-Er system at 673 K have been obtained, and the microstructures of as-cast alloys in the Al-rich region are also investigated. One ternary phase τ 1 -Al 8 Cu 4 Er with a composition of 59.4-60.4 at.% Al, 32.2-33.8 at.% Cu, and 6.4-7.7 at.% Er is observed in both as-cast and annealed alloys. At 673 K, the binary Al 3 Er phase dissolves about 3.51 at.% Cu. The calculated solidification paths (based on the CALPHAD method) of as-cast alloys are in agreement with the experimental results.

  12. Mechanical properties and deformation behavior of Al/Al7075, two-phase material

    International Nuclear Information System (INIS)

    Sherafat, Z.; Paydar, M.H.; Ebrahimi, R.; Sohrabi, S.

    2010-01-01

    In the present study, mechanical properties and deformation behavior of Al/Al7075, two-phase material were investigated. The two-phase materials were fabricated by mixing commercially pure Al powder with Al7075 chips and consolidating the mixture through hot extrusion process at 500 o C. Mechanical properties and deformation behavior of the fabricated samples were evaluated using tensile and compression tests. A scanning electron microscope was used to study the fracture surface of the samples including different amount of Al powder, after they were fractured in tensile test. The results of the tensile and compression tests showed that with decreasing the amount of Al powder, the strength increases and ductility decreases. Calculation of work hardening exponent (n) indicated that deformation behavior does not follow a regular trend. In a way that the n value was approved to be variable and a strong function of strain and Al powder wt% of the sample. The results of the fractography studies indicate that the type of fracture happened changes from completely ductile to nearly brittle by decreasing the wt% of Al powder from 90% to 40%.

  13. A Scholar from Saray: Mawlana Zada al-Sarayi (754/1353–791/1389 in the Biographical Dictionary of Taqi al-Din al-Maqrizi (766/1365–845/1441 “Kitab al-Muqaffa al-Kabir” (The Great Rhymed Book

    Directory of Open Access Journals (Sweden)

    D.R. Zaynuddinov

    2017-03-01

    Full Text Available Research objective: to introduce into academic circulation previously unknown source on the Golden Horde history. Research materials: biographical dictionary of Taqi al-Din al-Maqrizi (766/1365 – 845/1441 “Kitab al-Muqaffa al-Kabir” (The Great Rhymed Book. Results and novelty of the research: This article contains materials from the works of historians engaged in the narrative biography, which V.G. Tiesenhausen did not include in his “Collection of Materials on the Golden Horde history (extract from Arab writings”, although their writings contain very valuable information about the Golden Horde History. Research novelty consists in the fact that the author of this article presents one paragraph from biographical dictionary of Taqi al-Din al-Maqrizi, whose article number 421 provides information about a scholar from Saray – Mawlana Zada al-Sarayi. The author provides its translation and commentary referring to the more than ten medieval Arab sources. After receiving basic education at home, Mawlana Zada al-Sarayi traveled to many Eastern countries in search of knowledge and after having received high recognition he settled in Cairo as a teacher of Sharia Sciences. Despite the fact that his life was interrupted at an early age (36 years, he left a deep mark in science. His son Muhibbu al-Din (Cairo, 791/1389 – Mecca, Friday, the 3rd of Dhu al-Hijjah 859/13 November 1455 also became a great scholar as well as an imam of Sultan al-Ashraf Barsbay himself and other sultans after him. Nisba al-Sarayi sounded on the lips of the Ulema of the East as a symbol of learnedness and high temper. As a result of research it must be said that the study of life of Mawlana Zada al-Sarayi (754/1353 – 791/1389 and the number of migrants from Desht-i Kipchak in Egypt will help researchers in a deeper and more detailed study of the Golden Horde history.

  14. Improved AlGaN/GaN HEMTs Grown on Si Substrates Using Stacked AlGaN/AlN Interlayer by MOCVD

    International Nuclear Information System (INIS)

    Wang Yong; Yu Nai-Sen; Li Ming; Lau Kei-May

    2011-01-01

    AlGaN/GaN high electron mobility transistors (HEMTs) are grown on 2-inch Si (111) substrates by MOCVD. The stacked AlGaN/AlN interlayer with different AlGaN thickness and indium surfactant doped is designed and optimized to relieve the tensile stress during GaN epitaxial growth. The top 1.0μm GaN buffer layer grown on the optimized AlGaN/AlN interlayer shows a crack-free and shining surface. The XRD results show that GaN(002) FWHM is 480 arcsec and GaN(102) FWHM is 900 arcsec. The AGaN/GaN HEMTs with optimized and non-optimized AlGaN/AlN interlayer are grown and processed for comparison and the dc and rf characteristics are characterized. For the dc characteristics of the device with optimized AlGaN/AlN interlayer, maximum drain current density I dss of 737mA/mm, peak transconductance G m of 185mS/mm, drain leakage current density I ds of 1.7μA/mm, gate leakage current density I gs of 24.8 μA/mm and off-state breakdown voltage V BR of 67 V are achieved with L g /W g /L gs /L gd = 1/10/1/1 μm. For the small signal rf characteristics of the device with optimized AlGaN/AlN interlayer, current gain cutoff frequency f T of 8.3 GHz and power gain cutoff frequency f max of 19.9 GHz are achieved with L g /W g /L gs /L gd = 1/100/1/1 μm. Furthermore, the best rf performance with f T of 14.5 GHz and f max of 37.3 GHz is achieved with a reduced gate length of 0.7μm. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  15. Konsepsi Ibnu Jarir Al-Tabari Tentang Al-Qur’an, Tafsir Dan Ta’wil

    Directory of Open Access Journals (Sweden)

    A.M Ismatulloh

    2012-12-01

    Full Text Available The objective of this research is to describe the concept of Ibnu Jarir al-Tabari about al-Qur’an, tafsir and ta’wil. Ibn Jarir al-Tabari is an outstanding expert in the classic Islamic tradition. His knowledge in hadits, fiqh, lughah, history, and tafseer is unquestionable. This study uses an analytical descriptive design. The findings show that: Firstly, in defining al-Qur’an, al-Tabari focused on the al-Qur’an as an Arabic language text, not in other language. Secondly, al-Qur’an is written in sab’ah ahruf. It means that there are 7 different kinds of language with the same meaning. Thirdly, al-Qur’an comes from seven heaven’s door. Fourthly, there is no different word between tafseer and ta’wil. They have same meaning. These concepts are different to other concepts proposed by other ulama.

  16. Predicting glass-forming compositions in the Al-La and Al-La-Ni systems

    International Nuclear Information System (INIS)

    Gargarella, P.; de Oliveira, M.F.; Kiminami, C.S.; Pauly, S.; Kuehn, U.; Bolfarini, C.; Botta, W.J.; Eckert, J.

    2011-01-01

    Research highlights: → The glass-forming ability of the Al-La and Al-La-Ni systems was studied using the λ* and the λ.Δe criteria. → Both criteria predicted with just 1% at. of error the best glass-former verified so far in the Al-La system. → Four new glass-former compositions could be predicted in the Al-La-Ni system using the λ.Δe criterion. → The best glass-former reported so far in the Al-La-Ni system was found. - Abstract: In this work, a criterion considering the topological instability (λ) and the differences in the electronegativity of the constituent elements (Δe) was applied to the Al-La and Al-Ni-La systems in order to predict the best glass-forming compositions. The results were compared with literature data and with our own experimental data for the Al-La-Ni system. The alloy described in the literature as the best glass former in the Al-La system is located near the point with local maximum for the λ.Δe criterion. A good agreement was found between the predictions of the λ.Δe criterion and literature data in the Al-La-Ni system, with the region of the best glass-forming ability (GFA) and largest supercooled liquid region (ΔT x ) coinciding with the best compositional region for amorphization indicated by the λ.Δe criterion. Four new glassy compositions were found in the Al-La-Ni system, with the best predicted composition presenting the best glass-forming ability observed so far for this system. Although the λ.Δe criterion needs further refinements for completely describe the glass-forming ability in the Al-La and Al-La-Ni systems, the results demonstrated that this criterion is a good tool to predict new glass-forming compositions.

  17. Clay shale as host rock. A geomechanical contribution about Opalinus clay; Tonstein als Wirtsgestein. Ein geomechanischer Beitrag ueber Opalinuston

    Energy Technology Data Exchange (ETDEWEB)

    Lempp, Christof; Menezes, Flora; Sachwitz, Simon [Halle-Wittenberg Univ., Halle (Saale) (Germany). Inst. fuer Geowissenschaften und Geographie

    2016-12-15

    The Opalinuston is a prominent rock representing the type of organic clay shales or clay stones within the sequence of Triassic and Jurassic marine sediments in Southern Germany. The rock forms a homogenous unit some ten meters thick. The degree of consolidation of this type of pelitic rock depends mainly on the former load conditions, but is also dependent on the long-term weathering and even on the present exposition. The geomechanical parameters such as shear strength, tensional strength and permeability vary with the state of consolidation and become important when the use is discussed of such rocks for radioactive waste disposal. A tunneling project at the northern escarpment of the Swabian Alb (Southwest Germany) within the Opalinus clay offered the rare opportunity to obtain fresh unweathered rock samples in greater amounts compared to fresh drilling cores from which geomechanical investigations are usually undertaken. Consequently, the results of geomechanical laboratory testings are presented in order to compare here the results of multistep triaxial compression tests, of hydraulic fracturing laboratory tests and of some other tests for rock characterization with the corresponding results of Opalinus clay sites in Switzerland that were investigated by the Swiss Nagra Company for host rock characterization. After a discussion of the relevant state of fresh Opalinus clay, especially of suction pressure conditions and saturation state, the results of triaxial shear tests are presented. Increasing shear deformation at increasing pressure and unchanged water saturation do not result in a significant strength reduction of the Opalinus clay. The rock shows increasing cohesion and stiffness, if multiple loading has repeatedly reached the failure point. Thus there is no increased permeability with continued shearing. Only at the beginning of the shearing process is a temporarily increased permeability to be expected due to dilatation processes. An increased permeability, however, is generated by hydraulically injected water when fracturing may occur. Such fracturing depends on the injection rate: Low injection rates lead to local structural disintegration, higher injection rates result in single crack propagation as is known from hydraulic fracturing tests. Such hydraulically formed fractures later tend to close with an increase of surrounding stress. This closure increase is comparable to a healing process because new hydraulic fractures can be generated consequently at higher stress levels. Such laboratory test results seem to be favorable when using fresh Opalinus clay as a host rock, but they are difficult to verify at standard in-situ-conditions with weathered or partly deconsolidated rocks. Similar organic-rich and differently overconsolidated pelitic rock types display a wide spectrum of geomechanical behaviors despite the fact that no visible or physical differences can be provided. A direct comparison of the Opalinus clay parameters from the Swabian Alb, as investigated here, and from Switzerland, as determined by the Nagra Company, show differences in the effective shear strength. Nevertheless, the scatter is much smaller than that occurring for undrained shear stress differences as a function of water content. Consequently, for each project one must define exactly the relevant conditions within the different pelitic rocks in order to determine the useful geomechanical parameters. Additionally, it can be an advantage to use great depths because of the favorable geomechanical characteristics of Opalinus clay at high pressure. In this way some of the construction problems in Opalinus clay may be reduced if not avoided by using deep boreholes for waste deposition.

  18. Electric quadrupole moments of neutron-rich nuclei {sup 32}Al and {sup 31}Al

    Energy Technology Data Exchange (ETDEWEB)

    Kameda, D., E-mail: kameda@ribf.riken.jp; Ueno, H. [RIKEN Nishina Center (Japan); Asahi, K.; Nagae, D.; Takemura, M.; Shimada, K. [Tokyo Institute of Technology, Department of Physics (Japan); Yoshimi, A.; Nagatomo, T.; Sugimoto, T. [RIKEN Nishina Center (Japan); Uchida, M.; Arai, T.; Takase, K.; Suda, S.; Inoue, T. [Tokyo Institute of Technology, Department of Physics (Japan); Murata, J.; Kawamura, H. [Rikkyo University, Department of Physics (Japan); Watanabe, H. [Australian National University, Department of Nuclear Physics (Australia); Kobayashi, Y.; Ishihara, M. [RIKEN Nishina Center (Japan)

    2007-11-15

    The electric quadrupole moments for the ground states of {sup 32}Al and {sup 31}Al have been measured by the {beta} ray-detected nuclear quadrupole resonance method. Spin-polarized {sup 32}Al and {sup 31}Al nuclei were obtained from the fragmentation of {sup 40}Ar projectiles at E/A = 95 MeV/nucleon, and were implanted in a single crystal {alpha}-Al{sub 2}O{sub 3} stopper. The measured Q moment of {sup 32}Al, |Q({sup 32}Al)| = 24(2) mb, is in good agreement with a conventional shell-model calculation with a full sd model space and empirical effective charges, while that of {sup 31}Al is considerably smaller than the sd calculations.

  19. The constitution of alloys in the Al-rich corner of the Al-Si-Sm ternary system

    International Nuclear Information System (INIS)

    Markoli, B.; Spaic, S.; Zupanic, F.

    2001-01-01

    The constitution of alloys and the liquidus surface in the Al-rich corner of the Al-Si-Sm ternary system were determined by the examination of controlled heated and cooled specimens, as well as heat-treated specimens by means of optical and scanning electron microscopy, energy-dispersive X-ray spectroscopy, differential thermal analysis and X-ray diffraction. The Al-rich corner of the Al-Si-Sm ternary system comprises five regions of primary crystallisation (α Al , β Si , Al 3 Sm, Al 2 Si 2 Sm and AlSiSm) with following characteristic invariant reaction sequences: ternary eutectic reaction L → α Al + β Si + Al 2 Si 2 Sm, and two liquidus transition reactions, i. e., L + Al 3 Sm → α Al + AlSiSm, and L + AlSiSm → α Al + Al 2 Si 2 Sm. Along with the position of ternary eutectic and both interstitial points in the Al-rich corner of the Al-Si-Sm ternary system, the temperatures for each reaction were determined. (orig.)

  20. Disordered crystal structure of 20H-AlON, Al10O3N8

    International Nuclear Information System (INIS)

    Banno, Hiroki; Funahashi, Shiro; Asaka, Toru; Hirosaki, Naoto; Fukuda, Koichiro

    2015-01-01

    The disordered crystal structure of 20H-AlON (Al 10 O 3 N 8 ) was determined by combined use of X-ray powder diffraction and transmission electron microscopy. The title compound is hexagonal with space group P6 3 /mmc (Z=2) and the unit-cell dimensions are a=0.307082(5) nm, c=5.29447(8) nm and V=0.432376(12) nm 3 . The structural model showed the positional disordering of three of the six Al sites in the unit cell. The reliability indices calculated from the Rietveld method were R wp =6.97%, S (=R wp /R e )=1.68, R p =5.45%, R B =5.13% and R F =4.56%. We interpreted the disordered structure of 20H-AlON as a statistical average of six different types of ordered structural configurations, which are composed of an octahedral [Al(O, N) 6 ] layer and tetrahedral [Al(O, N) 4 ] layers. We demonstrated the high correlations between the hexagonal unit-cell dimensions and the octahedral layer concentrations for AlON and SiAlON polytypoids. - Graphical abstract: Variations of a and c/(n O +n T ) with n O /(n O +n T ). The a and c are the hexagonal unit-cell dimensions of AlON, SiAlON and AlN. The n O and n T are, respectively, the numbers of octahedral and tetrahedral layers in the unit cells. The unit-cell dimensions in literature are plotted in black plus for AlON and black cross for SiAlON. The unit-cell dimensions of AlN are a=0.3110 nm and c=0.4980 nm. - Highlights: • Crystal structure of Al10O3N8 is determined by laboratory X-ray powder diffraction. • The atom arrangements are represented by the split-atom model. • Six types of ordered atom arrangements are derived from the disordered structure. • Hexagonal unit-cell dimensions changed systematically for AlON and SiAlON compounds

  1. Prinsip Pendidikan Karakter dalam Islam: Studi Komparasi Pemikiran Al-Ghazali dan Burhanuddin Al-Zarnuji

    Directory of Open Access Journals (Sweden)

    Agus Setiawan

    2014-06-01

    Full Text Available The impelemtantion of character education that is done by the Indonesian government recently has been provoked by al-Ghazali and Burhanuddin al-Zarnuji long ago. It was proven by some written thoughts of al-Ghazali and Burhanuddin al-Zarnuji. They were very famous scientists in their era and widely welknown as educational experts who produced some phenomenal thoughts many people use today. Al-Ghazali and Burhanuddin al-Zarnuji lived in the era of Bani Abbasiyah monarchy, but Both of them lived in different era. Al-Ghazali was born first, then Burhanuddin al-Zarnuji. They had different mazhab, al-Ghazali went to the traditional principle of mazhab Syafi’I and Burhanuddin al-Zarnuji went to the modern principle of mazhab Hanafi. The differences, of course, would create a different thought. Still, they might have a similar principle of Islamic character education. The thoughts of character education of al-Ghazali have been poured in the “Ayyuha Walad” focusing to the students’ character building characterized by religiously obedient, skillfull of general and religious knowledge, socially helpful, affectionate, generous, good citizen, and coloring the society. Some applicable thoughts of character education of Ayyuha al-Walad of al-Gazhali to the contemporary education are: the balance of the happiness purposes of the recent life and the life after death, qana’ah and tawakal, affectionate, caring other, patience, honesty, philanthrophy, social works, generousity, democratic, peace makers, and patriotic. Those characters are also directed in the islamic character education nowdays. So that, the thoughts of al-Ghazali positively and responsively are absorbed by the Indonesian government to build the national character widely implementing in the national curriculum based on the local wisdom and the Islamic values. In the end, the students are able to live happily based on the Islamic rules by implementing the good behavior. Similar to the al

  2. FRACTIONAL RECRYSTALLIZATION KINETICS IN DIRECTLY COLD ROLLED Al-Mg, Al-Mg-Sc AND Al-Mg-Sc-Zr ALLOY

    Directory of Open Access Journals (Sweden)

    M. S. Kaiser

    2014-12-01

    Full Text Available The evaluation of texture as a function of recrystallization has been characterized for directly cold rolled Al-6Mg, Al-6Mg-0.4Sc and Al-6Mg-0.4Sc-0.2Zr alloys. Samples were annealed isothermally at 400 °C for 1 to 240 minutes to allow recrystallization. Recrystallization kinetics of the alloys is analyzed from the micro-hardness variation. Isothermally annealed samples of aluminum alloys were also studied using JMAK type analysis to see if there exists any correlation between the methods. Recrystallization fraction behavior between two methods the scandium added alloys show the higher variation due to precipitation hardening and higher recrystallization behavior. The scandium and zirconium as a combined shows the more variation due to formation of Al3(Sc, Zr precipitate. From the microstructure it is also observed that the base Al-Mg alloy attained almost fully re-crystallized state after annealing at 400 °C for 60 minutes

  3. Chemical failure modes of AlQ3-based OLEDs: AlQ3 hydrolysis.

    Science.gov (United States)

    Knox, John E; Halls, Mathew D; Hratchian, Hrant P; Schlegel, H Bernhard

    2006-03-28

    Tris(8-hydroxyquinoline)aluminum(III), AlQ3, is used in organic light-emitting diodes (OLEDs) as an electron-transport material and emitting layer. The reaction of AlQ3 with trace H2O has been implicated as a major failure pathway for AlQ3-based OLEDs. Hybrid density functional calculations have been carried out to characterize the hydrolysis of AlQ3. The thermochemical and atomistic details for this important reaction are reported for both the neutral and oxidized AlQ3/AlQ3+ systems. In support of experimental conclusions, the neutral hydrolysis reaction pathway is found to be a thermally activated process, having a classical barrier height of 24.2 kcal mol(-1). First-principles infrared and electronic absorption spectra are compared to further characterize AlQ3 and the hydrolysis pathway product, AlQ2OH. The activation energy for the cationic AlQ3 hydrolysis pathway is found to be 8.5 kcal mol(-1) lower than for the neutral reaction, which is significant since it suggests a role for charge imbalance in promoting chemical failure modes in OLED devices.

  4. Study on Mg/Al Weld Seam Based on Zn–Mg–Al Ternary Alloy

    Directory of Open Access Journals (Sweden)

    Liming Liu

    2014-02-01

    Full Text Available Based on the idea of alloying welding seams, a series of Zn–xAl filler metals was calculated and designed for joining Mg/Al dissimilar metals by gas tungsten arc (GTA welding. An infrared thermography system was used to measure the temperature of the welding pool during the welding process to investigate the solidification process. It was found that the mechanical properties of the welded joints were improved with the increasing of the Al content in the Zn–xAl filler metals, and when Zn–30Al was used as the filler metal, the ultimate tensile strength could reach a maximum of 120 MPa. The reason for the average tensile strength of the joint increasing was that the weak zone of the joint using Zn–30Al filler metal was generated primarily by α-Al instead of MgZn2. When Zn–40Al was used as the filler metal, a new transition zone, about 20 μm-wide, appeared in the edge of the fusion zone near the Mg base metal. Due to the transition zones consisting of MgZn2- and Al-based solid solution, the mechanical property of the joints was deteriorated.

  5. Optical, structural, and nuclear scientific studies of AlGaN with high Al composition

    Science.gov (United States)

    Lin, Tse Yang; Chung, Yee Ling; Li, Lin; Yao, Shude; Lee, Y. C.; Feng, Zhe Chuan; Ferguson, Ian T.; Lu, Weijie

    2010-08-01

    AlGaN epilayers with higher Al-compositions were grown by Metalorganic Chemical Vapor Deposition (MOCVD) on (0001) sapphire. Trimethylgallium (TMGa), trimethylaluminium (TMAl) and NH3 were used as the source precursors for Ga, Al, and N, respectively. A 25 nm AlN nucleation layer was first grown at low-temperature of 590 °C at 300 Torr. Followed, AlxGa1-xN layers were grown at 1080 °C on low-temperature AlN nucleation layers. The heterostructures were characterized by a series of techniques, including x-ray diffraction (XRD), Rutherford backscattering (RBS), photoluminescence (PL), scanning electron microscopy (SEM) and Raman scattering. Precise Al compositions were determined through XRD, RBS, and SEM combined measurements. Room Temperature Raman Scattering spectra shows three major bands from AlGaN alloys, which are AlN-like, A1 longitudinal optical (LO) phonon modes, and E2 transverse optical (TO) band, respectively, plus several peak comes from the substrate. Raman spectral line shape analysis lead to an optical determination of the electrical property free carrier concentration of AlGaN. The optical properties of AlGaN with high Al composition were presented here.

  6. Ion-beam mixing and thermal annealing of Al--Nb and Al--Ta thin films

    International Nuclear Information System (INIS)

    Rai, A.K.; Bhattacharya, R.S.; Mendiratta, M.G.; Subramanian, P.R.; Dimiduk, D.M.

    1988-01-01

    Ion-beam mixing and thermal annealing of thin, alternating layers of Al and Nb, as well as Al and Ta, were investigated by selected area diffraction and Rutherford backscattering. The individual layer thicknesses were adjusted to obtain the overall compositions as Al 3 Nb and Al 3 Ta. The films were ion mixed with 1 MeV Au + ions at a dose of 1 x 10 16 ions cm/sup -2/ . Uniform mixing and amorphization were achieved for both Al--Nb and Al--Ta systems. Equilibrium crystalline Al 3 Nb and Al 3 Ta phases were formed after annealing of ion mixed amorphous films at 400 0 C for 6 h. Unmixed films, however, remained unreacted at 400 0 C for 1 h. Partial reaction was observed in the unmixed film of Al--Nb at 400 0 C for 6 h. After annealing at 500 0 C for 1 h, a complete reaction and formation of Al 3 Nb and Al 3 Ta phases in the respective films were observed. The influence of thermodynamics on the phase formation by ion mixing and thermal annealing is discussed

  7. Effect of elevated Al and pH on the growth and root morphology of Al-tolerant and Al-sensitive wheat seedlings in an acid soil

    Directory of Open Access Journals (Sweden)

    Md. Toufiq Iqbal

    2014-03-01

    Full Text Available Aluminium ion (Al3+ toxicity and hydrogen ion (H+ activity are the major constraints for plant growth in acid soil. This study was undertaken to determine the effect of pH and Al on the growth response and changes in root morphology of Al-tolerant (ET8 and Al-sensitive (ES8 wheat seedlings. Different levels of AlCl3 and CaCO3 were added to the soils to manipulate soil pH and extractable Al. The results showed that the bulk soil pH remained constant at pH 4.1 with further applications of AlCl3, and that the seedlings died at the 200 mg AlCl3/kg treatments. The ET8 seedlings responded better than the ES8 seedlings in both low and high Al and pH. The ET8 seedlings had higher root surface areas and root tip numbers than the ES8 seedlings in the Al treatment. In contrast, the ES8 had higher root diameters than the ET8 seedlings due to the elevated Al supply. Apoplast Al increased with the increase of soil available extractable Al, and declined with the decrease of soil extractable Al. The ET8 seedlings accumulated more Al in their apoplast than the ES8 seedlings. This study concluded that accumulation of Al in the apoplast is also involved in Al tolerance mechanism with the addition of organic acid exudation.

  8. Information of “Nukhbat al-dahr fi ‘aja’ib al-barr wa-al-bahr” by ad-Dimashqi about the Turkic Tribes of Dasht-i Kipchak »

    Directory of Open Access Journals (Sweden)

    Z.S. Ilyasova

    2016-12-01

    Full Text Available This article introduced into academic circulation information of such a historical source as “Nukhbat al-dahr fi ‘aja’ib al-barr wa-al-bahr” (Excerpts of Time on the Marvels of the Land and Sea on Kipchak clans and Turkic tribes of Dasht-i Kipchak. The material of the study is drawn from this source. Main scientific result of this work was the source’s translation into Russian accompanied by scientific comments. Sheikh Shams al-Din Abu Abdallah Muhammad Abu Talib al-Ansari al-Sufi al-Dimashqi was the author of this work. Some scholars have mistakenly confuse him with another chronicler named Shihab al-Din Ahmad ibn Yahya Ibn Fadlallah al-Omari al-Dimashqi. There is a widespread misconception that while writing on Kipchak clans and Turkic tribes al-Dimashqi used the data of such an author as Muhammad ibn Ibrahim ibn Yahya al-Ansari al-Qutub al-Warraq al-Vatvat, also known as Ahmad al-Tini. After had studying the manuscripts of al-Tini and al-Dimashqi, we did not notice the connection between these two authors regarding their information about Kipchak clans and Turkic tribes of Dasht-i Kipchak. After had studying the information about Kipchak clans and Turkic tribes of Dasht-i Kipchak, we put forward the theory that 16 ethnonyms previously identified as Kipchak clans, are actually the etnonyms of eight Kipchak clans and eight Turkic tribes. The article also contains the extraction from “Nukhbat al-dahr fi ‘aja’ib al-barr wa-al-bahr” regarding the geography of Dasht-i Kipchak and the countries inhabited by the Turks. The following data are unique in this source: 1. The text describes such rivers as Ceyhun (Amu Darya, Seyhun (Syr Darya, Itil (Volga, as well as Khorezm and Khazar Seas (Aral and Caspian Seas. 2. Additionally, this text lists the following Turkic peoples: al-Kharlukhiya (Karluks, al-Khirgaziya (Kyrgyz, al-Kaymakiya (Kimaks, al-Guzziya (Oguz, al-Bazhanakiya (Pechenegs, al-Tuguzguziya (Uighurs, al-Khulkhiya (?, al

  9. Studies on SiC(p) reinforced Al-Al sub 3 Ni eutectic matrix composites

    International Nuclear Information System (INIS)

    Masrom, A.K.; Foo, L.C.; Ismail, A.B.

    1996-01-01

    An investigation on processing of Al-5.69wt% Ni eutectic with SiC particulate composites is reported. The intermetallic composites are prepared by elemental powder metallurgy route and sintered at two different temperatures, i.e., 600 degree C and 620 degree C. Results show that the metal matrix was Al-Al sub 3 Ni eutectic. The phase analysis by XRD identified the presence of Al sub 3 Ni and Al as dominant phases together with silicon and Al sub 4 C sub 3 phase as minor phases. The Al sub 4 C sub 3 and Si phases are formed during sintering due to SiC-Al interface reaction. SEM micrographs also reveal the formation of microvoid surrounding the SiC particle

  10. The constitution of alloys in the Al-rich corner of the Al-Si-Sm ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Markoli, B.; Spaic, S. [Ljubljana Univ. (Slovenia). Faculty of Natural Science and Engineering; Zupanic, F. [Maribor Univ. (Slovenia). Faculty of Mechanical Engineering

    2001-09-01

    The constitution of alloys and the liquidus surface in the Al-rich corner of the Al-Si-Sm ternary system were determined by the examination of controlled heated and cooled specimens, as well as heat-treated specimens by means of optical and scanning electron microscopy, energy-dispersive X-ray spectroscopy, differential thermal analysis and X-ray diffraction. The Al-rich corner of the Al-Si-Sm ternary system comprises five regions of primary crystallisation ({alpha}{sub Al}, {beta}{sub Si}, Al{sub 3}Sm, Al{sub 2}Si{sub 2}Sm and AlSiSm) with following characteristic invariant reaction sequences: ternary eutectic reaction L {yields} {alpha}{sub Al} + {beta}{sub Si} + Al{sub 2}Si{sub 2}Sm, and two liquidus transition reactions, i. e., L + Al{sub 3}Sm {yields} {alpha}{sub Al} + AlSiSm, and L + AlSiSm {yields} {alpha}{sub Al} + Al{sub 2}Si{sub 2}Sm. Along with the position of ternary eutectic and both interstitial points in the Al-rich corner of the Al-Si-Sm ternary system, the temperatures for each reaction were determined. (orig.)

  11. Electronic Structures and Bonding Properties of Ti2AlC and Ti3AlC2

    Institute of Scientific and Technical Information of China (English)

    MIN Xinmin; REN Yi

    2007-01-01

    The relation among electronic structure, chemical bond and property of Ti2AlC, Ti3AlC2 and doping Si into Ti2AlC was studied by density function and the discrete variation (DFT-DVM) method. After adding Si into Ti2AlC, the interaction between Si and Ti is weaker than that between Al and Ti, and the strengths of ionic and covalent bonds decrease both. The ionic and covalent bonds in Ti3AlC2, especially in Ti-Al, are stronger than those in Ti2AlC. Therefore, in synthesis of Ti2AlC, the addition of Si enhances the Ti3AlC2 content instead of Ti2AlC. The density of state (DOS) shows that there is mixed conductor characteristic in Ti2AlC and Ti3AlC2. The DOS of Ti3AlC2 is much like that of Ti2AlC. Ti2SixAl1-x C has more obvious tendency to form a semiconductor than Ti2AlC, which is seen from the obvious difference of partial DOS between Si and Al3p.

  12. Digital Transformation Canvas - Übersicht behalten und Handlungsfelder gestalten

    Science.gov (United States)

    Köster, Michael; Mache, Tobias

    Im Beitrag "Digital Transformation Canvas - Übersicht behalten und Handlungsfelder gestalten" wird zunächst grob auf die wesentlichen Herausforderungen, die mit der zunehmenden Digitalisierung einhergehen, eingegangen. Anschließend werden ausgewählte Konzepte des Business Transformation Management vorgestellt, die sich mit der grundlegenden Weiterentwicklung von Organisationen - wie es die Digitalisierung erfordert - auseinandersetzen. Eine detaillierte Einführung in die Methodik des Business Transformation Canvas, der sich mit den unterschiedlichsten Gestaltungsfeldern der Transformation auseinandersetzt und ein Framework für Transformationsprojekte darstellt, rundet den Beitrag ab. Er schließt mit einem Fazit und Ausblick.

  13. Processes, spheres of use and importance of sewage sludge disintegration; Verfahren, Einsatzgebiete und Bedeutung der Klaerschlammdesintegration

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, J. [Technische Univ. Braunschweig (Germany). Inst. fuer Siedlungswasserwirtschaft; Technische Univ. Braunschweig (Germany). Inst. fuer Mechanische Verfahrenstechnik

    1999-07-01

    The paper gives an overview of results attained by means of mechanical sludge disintegration methods and compares them with thermal and ozone treatment. The objective is to describe in scientific as well as application-oriented terms the opportunities held and limits to this process step of sludge treatment. (orig.) [German] Im Rahmen des Beitrags wird eine Uebersicht ueber die mit mechanischen Verfahren der Schlammdesintegration erreichten Ergebnisse und ein Vergleich mit der Waerme- und der Ozonbehandlung gegeben. Ziel des Beitrages ist es, die Moeglichkeiten und Grenzen dieses Prozessschrittes der Schlammbehandlung aus wissenschaftlicher wie aus anwendungsorientierter Sicht darzustellen. (orig.)

  14. Pornographie als Metapher

    Directory of Open Access Journals (Sweden)

    Caroline Schubarth

    2010-02-01

    Full Text Available In diesem Artikel werden unterschiedliche metaphorische Verwendungen des Pornografiebegriffs und deren Implikationen untersucht. Während die Existenz von Pornografie der feministischen Anti-Porno-Bewegung als Erklärung für die anhaltende Diskriminierung von Frauen in westlichen Gesellschaften dient, nutzen rechtskonservative Kräfte den Pornografievorwurf als Rechtfertigung für die Zensur von als deviant empfundenen Identitäten und sexuellen Praktiken.

  15. Deletion of ALS5, ALS6 or ALS7 increases adhesion of Candida albicans to human vascular endothelial and buccal epithelial cells

    OpenAIRE

    ZHAO, XIAOMIN; OH, SOON-HWAN; HOYER, LOIS L.

    2007-01-01

    C. albicans yeast forms deleted for ALS5, ALS6 or ALS7 are more adherent than a relevant control strain to human vascular endothelial cell monolayers and buccal epithelial cells. In the buccal and vaginal reconstituted human epithelium (RHE) disease models, however, mutant and control strains caused a similar degree of tissue destruction. Deletion of ALS5 or ALS6 significantly slowed growth of the mutant strain; this phenotype was not affected by addition of excess uridine to the culture medi...

  16. Alpha and beta stabilizer character of Al in Zr-Nb-Al alloys

    International Nuclear Information System (INIS)

    Peruzzi Bardella, A.; Bolcich, J.C.

    1987-01-01

    The T β/α+β of Zr5Nb and Zr5Nb2Al (weight %) were determined in order to observe the alpha-stabilizer character of Al in ternary Zr-Nb-Al alloys. Techniques employed were change of resistivity with temperature in dynamic experiences, and metallography of samples quenched to room temperature after isothermal annealings. The T β/α+β of the ternary resulted 17 ± 8 deg C higher than that of the binary alloy. In addition, taking into account the results of previous investigations of the transformation of beta on quenching Zr-Nb-Al alloys from the beta field to room temperature, it is concluded that the beta-stabilizer character of Nb is stronger than the alpha-stabilizer character of Al in these Zr alloys, and that the Al can have important influence on the mechanical properties by the appearance of TRIP effect. (Author) [es

  17. Insulator-semiconductor interface fixed charges in AlGaN/GaN metal-insulator-semiconductor devices with Al2O3 or AlTiO gate dielectrics

    Science.gov (United States)

    Le, Son Phuong; Nguyen, Duong Dai; Suzuki, Toshi-kazu

    2018-01-01

    We have investigated insulator-semiconductor interface fixed charges in AlGaN/GaN metal-insulator-semiconductor (MIS) devices with Al2O3 or AlTiO (an alloy of Al2O3 and TiO2) gate dielectrics obtained by atomic layer deposition on AlGaN. Analyzing insulator-thickness dependences of threshold voltages for the MIS devices, we evaluated positive interface fixed charges, whose density at the AlTiO/AlGaN interface is significantly lower than that at the Al2O3/AlGaN interface. This and a higher dielectric constant of AlTiO lead to rather shallower threshold voltages for the AlTiO gate dielectric than for Al2O3. The lower interface fixed charge density also leads to the fact that the two-dimensional electron concentration is a decreasing function of the insulator thickness for AlTiO, whereas being an increasing function for Al2O3. Moreover, we discuss the relationship between the interface fixed charges and interface states. From the conductance method, it is shown that the interface state densities are very similar at the Al2O3/AlGaN and AlTiO/AlGaN interfaces. Therefore, we consider that the lower AlTiO/AlGaN interface fixed charge density is not owing to electrons trapped at deep interface states compensating the positive fixed charges and can be attributed to a lower density of oxygen-related interface donors.

  18. Effects of Al(III and Nano-Al13 Species on Malate Dehydrogenase Activity

    Directory of Open Access Journals (Sweden)

    Rong Fu Chen

    2011-05-01

    Full Text Available The effects of different aluminum species on malate dehydrogenase (MDH activity were investigated by monitoring amperometric i-t curves for the oxidation of NADH at low overpotential using a functionalized multi-wall nanotube (MWNT modified glass carbon electrode (GCE. The results showed that Al(III and Al13 can activate the enzymatic activity of MDH, and the activation reaches maximum levels as the Al(III and Al13 concentration increase. Our study also found that the effects of Al(III and Al13 on the activity of MDH depended on the pH value and aluminum speciation. Electrochemical and circular dichroism spectra methods were applied to study the effects of nano-sized aluminum compounds on biomolecules.

  19. Effects of Al(III) and nano-Al13 species on malate dehydrogenase activity.

    Science.gov (United States)

    Yang, Xiaodi; Cai, Ling; Peng, Yu; Li, Huihui; Chen, Rong Fu; Shen, Ren Fang

    2011-01-01

    The effects of different aluminum species on malate dehydrogenase (MDH) activity were investigated by monitoring amperometric i-t curves for the oxidation of NADH at low overpotential using a functionalized multi-wall nanotube (MWNT) modified glass carbon electrode (GCE). The results showed that Al(III) and Al(13) can activate the enzymatic activity of MDH, and the activation reaches maximum levels as the Al(III) and Al(13) concentration increase. Our study also found that the effects of Al(III) and Al(13) on the activity of MDH depended on the pH value and aluminum speciation. Electrochemical and circular dichroism spectra methods were applied to study the effects of nano-sized aluminum compounds on biomolecules.

  20. Fracture toughness of Ti-Al3Ti-Al-Al3Ti laminate composites under static and cyclic loading conditions

    Science.gov (United States)

    Patselov, A. M.; Gladkovskii, S. V.; Lavrikov, R. D.; Kamantsev, I. S.

    2015-10-01

    The static and cyclic fracture toughnesses of a Ti-Al3Ti-Al-Al3Ti laminate composite material containing at most 15 vol % intermetallic compound are studied. Composite specimens are prepared by terminating reaction sintering of titanium and aluminum foils under pressure. The fracture of the titanium layers is quasi-cleavage during cyclic crack growth and is ductile during subsequent static loading.

  1. Data supporting Al-Abed et al., Environ. Sci.: Nano, 2016,

    Data.gov (United States)

    U.S. Environmental Protection Agency — Data files representing each of the Figures and Tables published in Al-Abed et al., Environ. Sci.: Nano, 2016, 3, 593. The data file names identify the Figure or...

  2. Ti, Al

    Indian Academy of Sciences (India)

    In the present study, authors report on the effect that substrate bias voltage has on the microstructure and mechanical properties of (Ti, Al)N hard coatings deposited with cathodic arc evaporation (CAE) technique. The coatings were deposited from a Ti0.5Al0.5 powder metallurgical target in a reactive nitrogen atmosphere at ...

  3. Growth of CdTe: Al films; Crecimiento de peliculas de CdTe: Al

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez A, M.; Zapata T, M. [CICATA-IPN, 89600 Altamira, Tamaulipas (Mexico); Melendez L, M. [CINVESTAV-IPN, A.P. 14-740, 07000 Mexico D.F. (Mexico); Pena, J.L. [CINVESTAV-IPN, A.P. 73 Cordemex, 97310 Merida, Yucatan (Mexico)

    2006-07-01

    CdTe: AI films were grown by the close space vapor transport technique combined with free evaporation (CSVT-FE). The Aluminum (Al) evaporation was made by two kinds of sources: one made of graphite and the other of tantalum. The films were deposited on glass substrates. The Al source temperature was varied maintaining the CdTe source temperature fixed as well as the substrate temperature. The films were characterized by x-ray energy dispersive analysis (EDAX), x-ray diffraction and optical transmission. The results showed for the films grown with the graphite source for Al evaporation, the Al did not incorporate in the CdTe matrix, at least to the level of EDAX sensitivity; they maintained the same crystal structure and band gap. For the samples grown with the tantalum source, we were able to incorporate the Al. The x-ray diffraction patterns show that the films have a crystal structure that depends on Al concentration. They were cubic up to 2.16 at. % Al concentration; for 19.65 at. % we found a mixed phase; for Al concentration higher than 21 at. % the films were amorphous. For samples with cubic structure it was found that the lattice parameter decreases and the band gap increases with Al concentration. (Author)

  4. First-principles study of L10 Ti-Al and V-Al alloys

    International Nuclear Information System (INIS)

    Chubb, S.R.; Papaconstantopoulos, D.A.; Klein, B.M.

    1988-01-01

    As a first step towards understanding the reduced embrittlement of L1 0 Ti-Al alloys which accompanies the introduction of small concentrations of V, we have determined from first principles, using full-potential linearized--augmented-plane-wave calculations, the equilibrium values of the structural parameters and the associated electronic structure for the stoichiometric (L1 0 ) Ti-Al (tetragonal) compound. Our calculated values of c/a and a are in good agreement with experiment. Using the same method of calculation, we have also studied the electronic structure associated with the (hypothetical) L1 0 V-Al alloy that would form when V is substituted for Ti. We find that (1) the electronic structures of these V-Al alloys are relatively insensitive to variations of c/a and a; (2) near the Ti-Al equilibrium geometry, the electronic structures of the V-Al and Ti-Al alloys are very similar; and (3) that a rigid-band model involving substitution of V for Ti can be used to gain a qualitative understanding of the reduction in c/a which accompanies the introduction of small concentrations of V. We relate the reduction in c/a to important changes in the bonding that accompany the occupation of bands immediately above the Fermi level of the stoichiometric Ti-Al compound

  5. Kinetic studies of oxidation of MgAlON and a comparison of the oxidation behaviour of AlON, MgAlON, O'SiAlON-ZrO{sub 2}, and BN-ZCM ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Wang Xidong; Seetharaman, S. [Div. of Metallurgy, Royal Inst. of Tech., Stockholm (Sweden); Li Wenchao [Dept. of Physical Chemistry, Univ. of Science and Technology Beijing (USTB), Beijing, BJ (China)

    2002-06-01

    The kinetics and morphology of the oxidation process of magnesium-aluminium oxynitride (MgAlON), aluminium oxynitride (AlON), O'SiAlON-ZrO{sub 2}, and BN-ZCM have been studied in the temperature range 1373-1773 K (ZCM=30 wt% ZrO{sub 2}, 52 wt% Al{sub 2}O{sub 3} and 18 wt% 3 Al{sub 2}O{sub 3}.2 SiO{sub 2}). Oxidation experiments with powder and plate samples of the above materials have been carried out in air. MgAlON shows the best resistance to oxidation at lower temperatures (< 1473 K), whereas at higher temperatures ({proportional_to} 773 K), AlON shows the best resistance. O'SiAlON-ZrO{sub 2} shows very good oxidation resistance up to 1673 K. But its oxidation rate increases strongly above 1673 K, presumably due to the formation of liquid phase. BN-ZCM has the poorest oxidation resistance due to the evaporation of B{sub 2}O{sub 3}. The activation energies for the chemical oxidation reaction of AlON, MgAlON, and O'SiAlON-ZrO{sub 2} are 214, 330 and 260 kJ/mol, respectively. The overall diffusion activation energies for AlON, MgAlON, O'SiAlON-ZrO{sub 2} and BN-ZCM are 227, 573, 367 and 289 kJ/mol, respectively. (orig.)

  6. Grain refining mechanism of Al-containing Mg alloys with the addition of Mn-Al alloys

    International Nuclear Information System (INIS)

    Qin, Gaowu W.; Ren Yuping; Huang Wei; Li Song; Pei Wenli

    2010-01-01

    Graphical abstract: Display Omitted Research highlights: The ε-AlMn phase acts as the heterogeneous nucleus of α-Mg phase during the solidification of the AZ31 Mg alloy, not the γ-Al 8 Mn 5 phase. The grain refinement effect is very clear with the addition of only 0.5 wt% Mn-28Al alloy (pure ε-AlMn). The grain refinement does not deteriorate up to the holding time of 60 min at 740 o C. - Abstract: The effect of manganese on grain refinement of Al-containing AZ31 Mg alloy has been investigated by designing a series of Mn-Al alloys composed of either pure ε-AlMn, γ 2 -Al 8 Mn 5 or both of them using optical microscopy and X-ray diffraction. It is experimentally clarified that the grain refinement of the AZ31 Mg alloy is due to the existence of the ε-AlMn phase in the Mn-Al alloys, not the γ 2 -Al 8 Mn 5 phase. The grain size of AZ31 Mg alloy is about 91 μm without any addition of Mn-Al alloys, but remarkably decreases to ∼55 μm with the addition of either Mn-34 wt% Al or Mn-28 wt% Al. With a minor addition of 0.5 wt% Mn-28Al alloy, the grain size of AZ31 alloy decreases to ∼53 μm, and the Mn-28Al alloy can be active as grain refiner for holding time up to 60 min for the melt AZ31 alloy at 750 o C.

  7. Ibn Qutayba en al-Andalus. La préface à I 'Adab al-Kātib dans le commentaire d'Ibn al-Sīd al-Baṭalyawsī

    Directory of Open Access Journals (Sweden)

    Soravia, Bruna

    2004-12-01

    Full Text Available Ibn Qutayba's preface to his Adab al-kātib has been considered for centuries the most important section of this work and it has been the object of many commentaries, both in the Muslim East and West. This paper deals with Ibn al-Sīd al-Baṭalyawsī´s commentary al-Iqtiḍāb, trying to show the peculiar way in which Ibn al-Sīd develops his own critique of Ibn Qutayba's controversial thesis on the relation between orthodoxy, falsafa and kalām. At the same time, the Andalusi author works out his own conception of adab, deeply influenced by his biographical experience. Finally a full translation of Ibn Qutayba's preface is proposed, half a century after G. Lecomte's partial one.

    El prefacio de Ibn Qutayba a su Adab al-Kātib ha sido considerado durante siglos como el fragmento más importante de su obra, y ha sido objeto de muchos comentarios, tanto orientales como occidentales. Este artículo trata del comentario que Ibn al-Sīd al-Baṭalyawsī hizo de ese texto de Ibn Qutayba, e intenta mostrar la forma peculiar en que Ibn al-Sīd desarrolla su propia crítica a la polémica tesis de Ibn Qutayba sobre la relación entre ortodoxia, falsafa y kalām. Al mismo tiempo, el autor andalusí elabora su propia concepción del adab, profundamente influida por su experiencia biográfica. Para concluir, se presenta una traducción completa del prefacio de Ibn Qutayba, medio siglo después de la parcial realizada por G. Lecomte.

  8. Cooperation with UNEP/IRPTC as a contribution to the implementation of the 'Agenda 21' action programme, chapter 19 in the field of information exchange on hazardous substances; Kooperation mit UNEP/IRPTC als Beitrag zur Umsetzung des Aktionsprogramms 'Agenda 21', Kapitel 19 im Bereich Informationsaustausch ueber gefaehrliche Stoffe

    Energy Technology Data Exchange (ETDEWEB)

    Schock-Schmelzer, U.

    1999-09-01

    Informationsaustausch ueber gefaehrliche Stoffe gestaerkt werden. Ganz im Sinne dieses Handlungsauftrages leistet die im Rahmen dieses Vorhabens realisierte enge Kooperation zwischen dem Umweltbundesamt und UNEP Chemicals (bis 1995 UNEP/IRPTC (United Nations Environment Programme / International Register of Potentially Toxic Chemicals)) mit dem Austausch wissenschaftlicher und rechtlicher Informationen zu gefaehrlichen Chemikalien einen konkreten und erfolgreichen Beitrag zur Umsetzung von Kapitel 19 der Agenda 21. UNEP Chemicals wurde bei verschiedenen Aufgaben im Bereich der Datenarbeit unterstuetzt. Im Gegenzug hierzu wurde der international erarbeitete und angesehene Datenbestand von UNEP Chemicals dem Umweltbundesamt zur direkten Verfuegung gestellt. Diese Kooperation mit UNEP Chemicals ist ein wichtiger Bestandteil der internationale n Zusammenarbeit beim Austausch von Daten ueber die Gefaehrlichkeit von chemischen Stoffen. (orig.)

  9. Structure and phase composition of Al-Ce-Cu system alloys in range of quasi-binary Al-Al8CeCu4 section

    International Nuclear Information System (INIS)

    Belov, N.A.; Khvan, A.V.

    2007-01-01

    The phase diagram of the Al-Cu-Ce system in the quasibinary section area of Al-Al 8 CeCu 4 has been investigated by metallographic, thermal, micro-X-ray spectral and X-ray structural analyses. The parameters of the eutectic reaction L→(Al)+CeCu 4 Al 8 : T=610 Deg C were found out; the composition was 14% Cu and 7% Ce. This eutectics is of a disperse structure and the ternary compound contained is capable of fragmentation and spheroidizing in the heating process (starting from 540 Deg C). It was demonstrated that the area of optimal (Al)+CeCu 4 Al 8 eutectics-based alloy compositions was within the narrow limits. That is related to the fact that at a comparatively little variation of the Cu:Ce=2 ratio solidus sharply decreases and, as a result, the crystallization interval considerably extends [ru

  10. Structural and electrical characterization of AuPtAlTi ohmic contacts to AlGaN/GaN with varying annealing temperature and Al content

    OpenAIRE

    Fay, Mike W.; Han, Y.; Brown, Paul D.; Harrison, Ian; Hilton, K.P.; Munday, A.; Wallis, D.; Balmer, R.S.; Uren, M.J.; Martin, T.

    2008-01-01

    The effect of varying annealing temperature and Al layer thickness on the structural and electrical characteristics of AuPtAlTi/AlGaN/GaN ohmic contact structures has been systematically investigated. The relationship between annealing temperature, Al content, interfacial microstructure, surface planarity and contact resistance is\\ud examined. In particular, the presence of a detrimental low temperature Pt-Al reaction is identified. This is implicated in both the requirement for a higher Al:T...

  11. Neuer Beitrag zur Kenntnis aussereuropaeischer Trichopteren

    NARCIS (Netherlands)

    Ulmer, Georg

    1906-01-01

    In den folgenden Mitteilungen findet man alles veröffentlicht, was mir zur Zeit an neuem und wenig bekannten Materiale (mit Ausnahme amerikanischer Arten, für die mir keine Typen vorliegen) zur Verfügung steht. Herr Dr. H. W. van der Weele in Leiden war so freundlich, mir die aussereuropäischen

  12. Zwischen "Arzt spielen", "Work-Life-Balance" und "Highend-Medizin". Wird "hegemoniale Männlichkeit" in der Medizin herausgefordert?

    Directory of Open Access Journals (Sweden)

    Katharina Rothe

    2015-11-01

    Full Text Available Wir diskutieren die Frage, ob eine sogenannte "Feminisierung" bestehende "maskuline" Machtstrukturen in der Medizin herausfordert. Die Rede von der "Feminisierung der Medizin" setzt sowohl die "Maskulinität" voraus als auch deren Veränderung durch die Erhöhung des Frauenanteils. Wir stellen die Kontrastanalyse zweier Gruppendiskussionen aus der Längsschnittstudie Karriereverläufe und Karrierebrüche bei Ärztinnen und Ärzten während der fachärztlichen Weiterbildung (KarMed vor; eine Diskussion mit angehenden Ärztinnen und eine mit angehenden Ärzten. Als manifestes Thema wurde Geschlechtlichkeit in beiden Diskussionen im diskursiven Kontext der sogenannten "Feminisierung" eingeführt – bezeichnenderweise im Kontrast zur gleichsam mythisch aufgeladenen Maskulinität der Chirurgie. Das Material unserer Gruppendiskussionen verweist auf eine nach wie vor maskuline Norm im Selbstverständnis der angehenden Ärztinnen und Ärzte. Die Männerrunde konstituierte sich als Gruppe der Ärzteschaft bei allen Differenzen wie selbstverständlich als männliche Norm. Die Frauengruppe konstituierte sich über eine geteilte Identifikation als "Frauen in der Medizin". Das Material wurde mit Methoden der psychoanalytischen Sozialforschung interpretiert und wird in diesem Beitrag im Hinblick auf die Begriffe der Feminisierung und der hegemonialen Männlichkeit diskutiert. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1601159

  13. Grain refining mechanism of Al-containing Mg alloys with the addition of Mn-Al alloys

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Gaowu W., E-mail: qingw@smm.neu.edu.c [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Wenhu Road 3-11, Heping District, Shenyang 110004, Liaoning Province (China); Ren Yuping; Huang Wei; Li Song; Pei Wenli [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Wenhu Road 3-11, Heping District, Shenyang 110004, Liaoning Province (China)

    2010-10-08

    Graphical abstract: Display Omitted Research highlights: The {epsilon}-AlMn phase acts as the heterogeneous nucleus of {alpha}-Mg phase during the solidification of the AZ31 Mg alloy, not the {gamma}-Al{sub 8}Mn{sub 5} phase. The grain refinement effect is very clear with the addition of only 0.5 wt% Mn-28Al alloy (pure {epsilon}-AlMn). The grain refinement does not deteriorate up to the holding time of 60 min at 740 {sup o}C. - Abstract: The effect of manganese on grain refinement of Al-containing AZ31 Mg alloy has been investigated by designing a series of Mn-Al alloys composed of either pure {epsilon}-AlMn, {gamma}{sub 2}-Al{sub 8}Mn{sub 5} or both of them using optical microscopy and X-ray diffraction. It is experimentally clarified that the grain refinement of the AZ31 Mg alloy is due to the existence of the {epsilon}-AlMn phase in the Mn-Al alloys, not the {gamma}{sub 2}-Al{sub 8}Mn{sub 5} phase. The grain size of AZ31 Mg alloy is about 91 {mu}m without any addition of Mn-Al alloys, but remarkably decreases to {approx}55 {mu}m with the addition of either Mn-34 wt% Al or Mn-28 wt% Al. With a minor addition of 0.5 wt% Mn-28Al alloy, the grain size of AZ31 alloy decreases to {approx}53 {mu}m, and the Mn-28Al alloy can be active as grain refiner for holding time up to 60 min for the melt AZ31 alloy at 750 {sup o}C.

  14. Online measuring devices at sewage treatment plants - state of the art and future market potential; On-Line-Messtechnik auf Klaeranlagen - Aktueller Stand und Marktpotential fuer die Zukunft

    Energy Technology Data Exchange (ETDEWEB)

    Baumann, P [Inst. fuer Siedlungswasserbau, Wasserguete- und Abfallwirtschaft der Univ. Stuttgart, Abt. Abwassertechnik (Germany); Schlegel, S [Emschergenossenschaft, Essen (Germany)

    1998-12-31

    By means of a survey commissioned by ATV/GFA, the purposes of use and spheres of use as well as the operating experience with online measuring devices for the determination of ammonium, oxidized nitrogen compounds and orthophosphate were established and evaluated. In addition, data were acquired with the aid of other units for the continuous recording of chemical and physical parameters of sewage treatment. Finally, the future market potentials and development pospects of online measuring devices were evaluated. (orig.) [Deutsch] Anhand einer im Auftrag der ATV/GFA durchgefuehrten Umfrage wurden Einsatzzweck, Einsatzbereiche und Betriebserfahrungen von On-line-Messgeraeten zur Bestimmung von Ammonium, oxidierten Stickstoffverbindungen und Orthophosphat dargestellt und bewertet. Zusaetzlich wurden auch Daten von anderen Geraeteeinheiten zur kontinuierlichen Erfassung von chemischen und physikalischen Parametern bei der Abwasserreinigung erhoben. Anschliessend wurde das zukuenftige Marktpotential und die Entwicklungsmoeglichkeiten bei der On-line-Messtechnik bewertet. (orig.)

  15. Online measuring devices at sewage treatment plants - state of the art and future market potential; On-Line-Messtechnik auf Klaeranlagen - Aktueller Stand und Marktpotential fuer die Zukunft

    Energy Technology Data Exchange (ETDEWEB)

    Baumann, P. [Inst. fuer Siedlungswasserbau, Wasserguete- und Abfallwirtschaft der Univ. Stuttgart, Abt. Abwassertechnik (Germany); Schlegel, S. [Emschergenossenschaft, Essen (Germany)

    1997-12-31

    By means of a survey commissioned by ATV/GFA, the purposes of use and spheres of use as well as the operating experience with online measuring devices for the determination of ammonium, oxidized nitrogen compounds and orthophosphate were established and evaluated. In addition, data were acquired with the aid of other units for the continuous recording of chemical and physical parameters of sewage treatment. Finally, the future market potentials and development pospects of online measuring devices were evaluated. (orig.) [Deutsch] Anhand einer im Auftrag der ATV/GFA durchgefuehrten Umfrage wurden Einsatzzweck, Einsatzbereiche und Betriebserfahrungen von On-line-Messgeraeten zur Bestimmung von Ammonium, oxidierten Stickstoffverbindungen und Orthophosphat dargestellt und bewertet. Zusaetzlich wurden auch Daten von anderen Geraeteeinheiten zur kontinuierlichen Erfassung von chemischen und physikalischen Parametern bei der Abwasserreinigung erhoben. Anschliessend wurde das zukuenftige Marktpotential und die Entwicklungsmoeglichkeiten bei der On-line-Messtechnik bewertet. (orig.)

  16. AYAT-AYAT WAH}DAT AL-WUJUd dalam Kitab Tanbi>h al-Ma>shi Karya ‘Abdurrauf al-Sinkili

    Directory of Open Access Journals (Sweden)

    Asep Nahrul Musadad

    2015-08-01

    Full Text Available Abstract: One of the key moments in discussing the history of Indonesian Islam is a polemic related to the negotiation on the doctrine of wahdat al-wujud that occured in Aceh in 17th century between the followers of Hamzah al-Fansuri and Nuruddin al-Raniri. This article focuses on analyzing several Qur’anic verses used by ‘Abdurrauf as the confirmation of his argument. In the polemical context, Abdurrauf al-Sinkili appeared to be an actor of reconciliation between two opposite sides. He tried to respond to the disputed issues through his book called “Tanbi>h al-Mashi”. As an exponent of the so-called moderate sufism (mysticism, he built the argument concerning wah}dat al-wujud based on the Quranic text. After making a thematic classification chronologically, his interpretation on these verses is analyzed by using Hussain al-Dhahaby’s theory of sufistic exegesis. In conclusion, it shows that ‘Abdurrauf’s commentary is “sufi-nazari type”, featured by his exegeses pattern. This, of course, represents his attitude as a reconciler who then needs to seek confirmation to the Qur’anic verses in evaluating wah}dat al-wujud doctrine, through which such a polemical issues occurred at that time. الملخص: إن من المرحلة الأساسية التي مرّ بها تاريخ الإسلام في اندونيسيا الجدل و النزاع حول عقيدة وحدة الوجود فى أتشيه (Aceh حول قرن السابع عشر بين أتباع حمزة الفنسوري و نور الدين الرانيري. ففي ذلك الخطاب النزاعي جاء عبد الرؤوف السنكيلي مصلحا بين الجانبين المعاكسين. وعلى مقتضى الظروف، كتب كتاب " تنبيه الماشي" الذي تطرّق فيه طريق التوسّط، ممثّلا للتصوّف المعتدل. اعتمد عبد الرؤوف على النصوص القرآنية فى تحقيق آراءه حول ت

  17. Reviewing Medical Education in KamelAl-Senaat Al-Tebieh

    Directory of Open Access Journals (Sweden)

    Shahla Moradi

    2017-06-01

    Full Text Available Background and Objective: Among the human sciences, medicine is superior to all other sciences. One of the effective factors in education, especially in medical education is using appropriate textbooks. This study aims to consider a classic book of medical education and find its relevance to modern medicine. Materials and Methods: Reviewing and analyzing parts of Kamel Al-Senaat Al-Tebieh medical textbook. Results: This book has about four hundred thousand words and it was divided into twenty articles, each consisting of several chapters, first ten topics of which are about theoretical medicine, and others are information related to practical medicine. Conclusion: One of the most important obligations of every nation is to protect and preserve written and unwritten cultural and scientific resources Kamel Al-Senaat Al-Tebieh was written in one of the glorious periods of Iranian Medical History by Ali Ibn Abbas. It has a dignified position because of its recording method. This method is one of the best methods that is used after Ahvazi. Even today it is a valuable source of medical education.

  18. Density and atomic volume in liquid Al-Fe and Al-Ni binary alloys

    Energy Technology Data Exchange (ETDEWEB)

    Plevachuk, Yu. [Ivan Franko National Univ., Lviv (Ukraine). Dept. of Metal Physics; Egry, I.; Brillo, J.; Holland-Moritz, D. [Deutsches Zentrum fuer Luft- und Raumfahrt, Koeln (Germany). Inst. fuer Raumsimulation; Kaban, I. [Chemnitz Univ. of Technolgy (Germany). Inst. of Physics

    2007-02-15

    The density of liquid Al-Fe and Al-Ni binary alloys have been determined over a wide temperature range by a noncontact technique combining electromagnetic levitation and optical dilatometry. The temperature and composition dependences of the density are analysed. A negative excess volume correlates with the negative enthalpy of mixing, compound forming ability and chemical short-range ordering in liquid Al-Fe and Al-Ni alloys. (orig.)

  19. TEM characterization of Al-C-Cu-Al2O3 composites produced by mechanical milling

    International Nuclear Information System (INIS)

    Santos-Beltran, A.; Gallegos-Orozco, V.; Estrada-Guel, I.; Bejar-Gomez, L.; Espinosa-Magana, F.; Miki-Yoshida, M.; Martinez-Sanchez, R.

    2007-01-01

    Novel Al-based composites (Al-C-Cu-Al 2 O 3 ) obtained by mechanical milling (MM), were characterized by transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS). Analyses of composites were carried out in both, the as-milled and the as-sintered conditions. C nanoparticles were found in the as-milled condition and Al 2 O 3 nanofibers were found in as-sintered products, as determined by EELS. C and Cu react with Al to crystallize in Al 3 C 4 and Al 2 Cu structures, respectively

  20. Formation of AlFeSi phase in AlSi12 alloy with Ce addition

    Directory of Open Access Journals (Sweden)

    S. Kores

    2012-04-01

    Full Text Available The influence of cerium addition on the solidification sequence and microstructure constituents of the Al-Si alloys with 12,6 mass % Si was examined. The solidification was analyzed by a simple thermal analysis. The microstructures were examined with conventional light and scanning electron microscopy. Ternary AlSiCe phase was formed in the Al-Si alloys with added cerium during the solidification process. AlSiCe and β-AlFeSi phases solidified together in the region that solidified the last. Cerium addition influenced on the morphology of the α-AlFeSi phase solidification.

  1. Compressive performance and crack propagation in Al alloy/Ti{sub 2}AlC composites

    Energy Technology Data Exchange (ETDEWEB)

    Hanaor, D.A.H., E-mail: dorian.hanaor@sydney.edu.au [School of Civil Engineering, University of Sydney, Sydney, NSW 2006 (Australia); Hu, L. [Ames Laboratory, U.S. Department of Energy, Ames, Iowa 50011 (United States); Kan, W.H.; Proust, G. [School of Civil Engineering, University of Sydney, Sydney, NSW 2006 (Australia); Foley, M. [Australian Centre for Microscopy and Microanalysis, University of Sydney, Sydney, NSW 2006 (Australia); Karaman, I.; Radovic, M. [Department of Materials Science and Engineering, Texas A& M University, College Station, TX 77843 (United States)

    2016-08-30

    Composite materials comprising a porous Ti{sub 2}AlC matrix and Al 6061 alloy were fabricated by a current-activated pressure assisted melt infiltration process. Coarse, medium and fine meso-structures were prepared with Al alloy filled pores of differing sizes. Materials were subjected to uniaxial compressive loading up to stresses of 668 MPa, leading to the failure of specimens through crack propagation in both phases. As-fabricated and post-failure specimens were analysed by X-ray microscopy and electron microscopy. Quasi-static mechanical testing results revealed that compressive strength was the highest in the fine structured composite materials. While the coarse structured specimens exhibited a compressive strength of 80% relative to this. Reconstructed micro-scale X-ray tomography data revealed different crack propagation mechanisms. Large planar shear cracks propagated throughout the fine structured materials while the coarser specimens exhibited networks of branching cracks propagating preferentially along Al alloy-Ti{sub 2}AlC phase interfaces and through shrinkage pores in the Al alloy phase. Results suggest that control of porosity, compensation for Al alloy shrinkage and enhancement of the Al alloy-Ti{sub 2}AlC phase interfaces are key considerations in the design of high performance metal/Ti{sub 2}AlC phase composites.

  2. Phase equilibria and crystalline structure of compounds in the Lu-Al and Lu-Cu-Al systems

    International Nuclear Information System (INIS)

    Kuz'ma, Yu.B.; Stel'makhovich, B.M.; Galamushka, L.I.

    1992-01-01

    Phase equilibria and crystal structure of compounds in Lu-Al and Lu-Cu-Al systems were studied. Existence of Lu 2 Al compound having the structure of the PbCl 2 type is ascertained. Diagram of phase equilibria of Lu-Cu-Al system at 870 K is plotted. Compounds Lu 2 (Cu,Al) 17 (the Th 2 Zn 17 type structure), Lu(Cu,Al) 5 (CaCu 5 type structure), Lu 6 (Cu,Al) 23 (Th 6 Mn 23 type structure) and ∼ LuCuAl 2 have been prepared for the first time. Investigation of component interaction in Lu-Cu-Al system shows that the system is similar to previously studied systems Dy-Cu-Al and Er-Cu-Al. The main difference consists in the absence of LuCuAl 3 compound with rhombic structure of the CeNi 2+x Sb 2-x type in the system investigated

  3. Al Qaeda in the Arabian Peninsula (AQAP): An Al Qaeda Affiliate Case Study

    Science.gov (United States)

    2017-10-01

    Villarosa, Al-Qaeda in Yemen, Carnegie Endowment, July 7, 2009, http://carnegieendowment.org/2009/07/07/Al-Qaeda-in-yemen- event-1372. 53 Brian Whitaker...73 Khaled Fattah, “Yemen’s Insecurity Dilemma,” Yemen Times, February 11, 2014, http:// carnegie -mec.org/2014/02...Johnsen, and Shari Villarosa, “Al-Qaeda in Yemen.” Carnegie Endowment. July 7, 2009. http://carnegieendowment.org/2009/07/07/Al-Qaeda-in- yemen-event

  4. Formation of epitaxial Al 2O 3/NiAl(1 1 0) films: aluminium deposition

    Science.gov (United States)

    Lykhach, Y.; Moroz, V.; Yoshitake, M.

    2005-02-01

    Structure of epitaxial Al 2O 3 layers formed on NiAl(1 1 0) substrates has been studied by means of reflection high-energy electron diffraction (RHEED). The elucidated structure was compared to the model suggested for 0.5 nm-thick Al 2O 3 layers [K. Müller, H. Lindner, D.M. Zehner, G. Ownby, Verh. Dtsch. Phys. Ges. 25 (1990) 1130; R.M. Jaeger, H. Kuhlenbeck, H.J. Freund, Surf. Sci. 259 (1991) 235]. The stepwise growth of Al 2O 3 film, involving deposition and subsequent oxidation of aluminium onto epitaxial 0.5 nm-thick Al 2O 3 layers, has been investigated. Aluminium was deposited at room temperature, whereas its oxidation took place during annealing at 1070 K. The Al 2O 3 thickness was monitored by means of Auger electron spectroscopy (AES). It was found that Al 2O 3 layer follows the structure of 0.5 nm thick Al 2O 3 film, although a tilting of Al 2O 3(1 1 1) surface plane with respect to NiAl(1 1 0) surface appeared after Al deposition.

  5. Amyotrophic lateral sclerosis (ALS)

    Science.gov (United States)

    Lou Gehrig disease; ALS; Upper and lower motor neuron disease; Motor neuron disease ... One out of 10 cases of ALS is due to a genetic defect. The cause is unknown in most other cases. In ALS, motor nerve cells (neurons) waste away ...

  6. The Role of Amateur Football in Circular Migration Systems in South Africa Zur Bedeutung des Amateurfußballs für zirkuläre Migrationssysteme in Südafrika

    Directory of Open Access Journals (Sweden)

    Malte Steinbrink

    2010-01-01

    Full Text Available This article explores the significance of amateur football for the changing patterns of circular migration in post-Apartheid South Africa. Even after the end of Apartheid, the abolishment of the migrant labour system has not brought a decline of circular migration. The state-institutionalised system has merely been replaced by an informal system of translocal livelihood organisation. The new system fundamentally relies on social networks and complex rural-urban linkages. Mobile ways of life have evolved that can be classified as neither rural nor urban. Looking into these informal linkages can contribute to explaining the persistence of spatial and social disparities in “New South Africa”. This paper centres on an empirical, bi-local case study that traces the genesis of the socio-spatial linkages between a village in former Transkei and an informal settlement in Cape Town. The focus is on the relevance of football for the emergence and stabilisation of translocal network structures. Der vorliegende Beitrag untersucht die Bedeutung des Amateurfußballs für zirkuläre Migrationsmuster im heutigen Südafrika. Der Umfang zirkulärer Migration hat nach dem Ende der Apartheid und der Abschaffung des Wanderarbeitssystems nicht abgenommen, vielmehr wurde das institutionalisierte staatliche System durch ein informelles System translokaler Strategien zur Existenzsicherung ersetzt. Dieses neue System basiert auf sozialen Netzwerken und komplexen Land-Stadt-Verbindungen; die so entstandene mobile Lebensweise kann weder als urban noch als ländlich charakterisiert werden. Eine Untersuchung dieser informellen Verbindungen kann dazu beitragen, die Fortdauer räumlicher und sozialer Ungleichheiten im “Neuen Südafrika” zu erklären. Im Zentrum des Beitrags steht eine bilokale Fallstudie, in der der Autor die Spuren sozialräumlicher Verbindungen zwischen einem Dorf in der früheren Transkei und einer informellen Siedlung in Kapstadt zur

  7. Pemikiran Politik al-Shawkânî dalam Fath al-Qadîr

    Directory of Open Access Journals (Sweden)

    Yusuf Hanafi

    2015-09-01

    Full Text Available Muhammad b. ‘Alî Muhammad b. ‘Abd Allâh al-Shawkânî al-San‘ânî. He was born in the Hijrah in Shawkân village, Yemen on Monday 28 Dhû al-Qa‘dah 1172 H and died on Tuesday, 27 Jumâd al-Akhîr 1250 H at the age about 78 years. Al-Shawkânî grew up in the San‘a city, it is the capital of the republic of Yemen now. He study first time about religion from his father, then from renowed scholars in San‘a and its surrounding, he was known as a scolar who mastered the various branches of religious sciences. Such as tafsîr, h}adîth, fiqh, us}ûl al-fiqh, history, science of kalâm, philosophy, balâghah, mant}iq etc. the main issue in this article is how political thought in the book of tafsir Fath al-Qadîr is the work of Shawkânî. At the end of article, the authors found that the intended political thinking in the study of Fath al-Qadîr is about constitutional ideas. These ideas about the constitution is limited to the concept of leadership and deliberation, the concept of the right of citizen to obtain justice, and the concept pf the right of citizens to live association and assembly

  8. Oxidation behavior of Al/Cr coating on Ti2AlNb alloy at 900 °C

    Science.gov (United States)

    Yang, Zhengang; Liang, Wenping; Miao, Qiang; Chen, Bowen; Ding, Zheng; Roy, Nipon

    2018-04-01

    In this paper, the Al/Cr coating was fabricated on the surface of Ti2AlNb alloy via rf magnetron sputtering and double glow treatment to enhance oxidation resistance. The protective coating with an outer layer of Al and inner layer of Cr has great bonding strength due to the in-diffusion of Cr and the inter-diffusion between Al and Cr to form Al-Cr alloyed layer which has great hardness. Acoustic emission curve which was detected via WS-2005 scratch tester indicates the bonding strength between Al/Cr coating and substrate is great. Morphology of Ti2AlNb alloy with Al/Cr coating after scratch test shows that the scratch is smooth without disbanding, and the depth and breadth of scratch are changed uniformly. The mass change was reduced after oxidation test due to the Al/Cr protective coating. Isothermal oxidation test at 900 °C was researched. Results indicate that Al/Cr coating provided oxidation resistance of Ti2AlNb alloy with prolonged air exposure at 900 °C. Al2O3 was detected by XRD patterns and SEM images, and was formed on the surface of Ti2AlNb alloy to protect substrate during oxidation test. A certain content of Cr is beneficial for the formation of Al2O3. Besides, Cr2O3 was produced under Al2O3 by outward diffusion of Cr to protect substrate sequentially, no cracks were discovered on Al/Cr protective coating. The process of Ti outward diffusion into surface was suppressive due to integration of Cr-Ti and Al-Ti intermetallics. A steady, adherent and continuous coated layer of Al/Cr on Ti2AlNb alloy increases oxidation resistance.

  9. ¿COLOMBIA DEBE APOSTARLE AL SOFTWARE LIBRE, AL DE FUENTE ABIERTA O AL PROPIETARIO?

    Directory of Open Access Journals (Sweden)

    Luis Alberto Girón Murillo

    2014-06-01

    Full Text Available Es complejo para gestores y administradores conocer las implicaciones que la adopción de modelos de desarrollo de software tendría para una región. Este artículo ofrece una evaluación de las implicaciones dinámicas que para el desarrollo de software de una región tendría el apostar de forma excluyente al software libre, al software de fuente abierta y al software propietario. Se desarrolló un modelo de simulación en Vensim de la dinámica de sistemas en donde se evaluaron 3 escenarios: uno en donde se adopta de forma excluyente el software libre, uno en donde se adopta el software propietario y uno en donde se adopta el software de fuente abierta. Se ofrecen descripciones y explicaciones de los resultados que sugieren las potencialidades de cada uno de los modelos de desarrollo evaluados.

  10. Investigation of annealing treatment on the interfacial properties of explosive-welded Al/Cu/Al multilayer

    International Nuclear Information System (INIS)

    Honarpisheh, M.; Asemabadi, M.; Sedighi, M.

    2012-01-01

    Highlights: ► We studied explosive-welded Al/Cu/Al multilayer. ► We investigated heat treatment influence on the bond properties of Al/Cu/Al. ► Intermetallic compounds were studied using the SEM, OM and EDS analysis. ► Variations of hardness in the thickness were investigated using micro-hardness. ► Intermetallic phases such as AlCu 3 and Al 2 C create at the interface of Al/Cu/Al. -- Abstract: In this study, an Al/Cu/Al multilayer sheet was fabricated by explosive welding process and the effects of annealing temperature on the interfacial properties of explosively bonded Al/Cu bimetal have been investigated. For this purpose, hardness changes along the thickness of the samples have been measured, and the thickness and type of intermetallic compounds formed at the joining interface have been explored by means of optical microscopy (OM), scanning electron microscopy (SEM) and also energy dispersive spectroscopy (EDS). The obtained results indicate that, with the increase of the annealing temperature, the thickness of intermetallic compounds has increased and the amount of hardness along the thickness of the joining interface has diminished. In the annealed sample at 400 °C for 30 min, it was observed that intermetallic layers have formed at the interface of Al/Cu bimetals. These layers consist of the intermetallic compounds AlCu 3 , Al 2 Cu and AlCu, and their thickness gets to about 5 μm at some points. The examinations performed by the SEM, following the Vickers micro-hardness test, indicated the existence of a number of microcracks at the top and bottom interface of the sample annealed at 400 °C. This shows the formation of brittle intermetallic compounds at the joining interface, and also indicates the low ductility of these compounds.

  11. NMR evidence for Co-Al-Co molecular groups trapped in cages of Co4Al13

    International Nuclear Information System (INIS)

    Jeglic, P.; Heggen, M.; Feuerbacher, M.; Bauer, B.; Gille, P.; Haarmann, F.

    2009-01-01

    We present the results of 27 Al nuclear magnetic resonance (NMR) experiments on the phase Co 4 Al 13 . These results are compared to a recent structure model [1], which demonstrates a unique bonding for Al atoms in the Co-Al-Co molecular groups. In our measurement, two 27 Al signals were identified. The first one originates from Al atoms forming cages. The second signal corresponds to Al sites with exceptionally large almost axially symmetric quadrupole coupling. This finding is in perfect agreement with isolated Co-Al-Co molecular groups in accordance to Ref. [1].

  12. The Y-Cu-Al system

    International Nuclear Information System (INIS)

    Krachan, T.; Stel'makhovych, B.; Kuz'ma, Yu.

    2003-01-01

    The phase diagram of the Y-Cu-Al system at 820 K has been constructed using X-ray powder diffraction. The existence of earlier known ternary aluminides has been confirmed and their homogeneity regions and atomic distributions in the structures have been determined: YCu 4.6-4.0 Al 7.4-8.0 (ThMn 12 -type R I =0.049), Y 2 Cu 12.0-10.5 Al 5.0-6.5 (Th 2 Zn 17 -type R I =0.092), YCu 1.0-1.1 Al 1.0-0.9 (Fe 2 P-type R I =0.068). It has been shown that the structure of Y(Cu,Al) 3 is characterized by an ordered distribution of the Cu and Al atoms and it should be referred as Ca 3 Cu 2 Al 7 structure type (R I =0.060) besides the PuNi 3 structure type with statistical occupancies of the smaller atoms. At the investigated temperature the compound YCu 1.0-0.25 Al 3.0-3.75 (BaAl 4 -type) was not observed. However, we found the ternary aluminide with composition Y 3 Cu 2.7-2.0 Al 8.3-9.0 and related La 3 Al 11 -type (space group Immm, a=0.4192-0.4228, b=1.2423-1.2557, c=0.9812-0.9895 nm, R I =0.069). The compounds YCu 6.8 Al 4.2 (space group Fddd, Tb(Cu 0.58 Al 0.42 ) 11 -type, a=1.42755, b=1.48587, c=0.65654 nm, R I =0.062) and YCu 6.5 Al 4.5 (space group I4 1 /amd, BaCd 11 -type, a=1.02774, c=0.65838 nm, R I =0.071) have been found and structurally refined for the first time

  13. Preparation, deformation, and failure of functional Al-Sn and Al-Sn-Pb nanocrystalline alloys

    Science.gov (United States)

    Noskova, N. I.; Vil'Danova, N. F.; Filippov, Yu. I.; Churbaev, R. V.; Pereturina, I. A.; Korshunov, L. G.; Korznikov, A. V.

    2006-12-01

    Changes in the structure, hardness, mechanical properties, and friction coefficient of Al-30% Sn, Al-15% Sn-25% Pb, and Al-5% Sn-35% Pb (wt %) alloys subjected to severe plastic deformation by equal-channel angular pressing (with a force of 40 tonne) and by shear at a pressure of 5 GPa have been studied. The transition into the nanocrystalline state was shown to occur at different degrees of plastic deformation. The hardness exhibits nonmonotonic variations, namely, first it increases and subsequently decreases. The friction coefficient of the Al-30% Sn, Al-15% Sn-25% Pb, and Al-5% Sn-35% Pb alloys quenched from the melt was found to be 0.33; the friction coefficients of these alloys in the submicrocrystalline state (after equal-channel angular pressing) equal 0.24, 0.32, and 0.35, respectively. The effect of disintegration into nano-sized powders was found to occur in the Al-15% Sn-25% Pb, and Al-5% Sn-35% Pb alloys after severe plastic deformation to ɛ = 6.4 and subsequent short-time holding.

  14. Characterization of Al/Ni multilayers and their application in diffusion bonding of TiAl to TiC cermet

    International Nuclear Information System (INIS)

    Cao, J.; Song, X.G.; Wu, L.Z.; Qi, J.L.; Feng, J.C.

    2012-01-01

    The Al/Ni multilayers were characterized and diffusion bonding of TiAl intermetallics to TiC cermets was carried out using the multilayers. The microstructure of Al/Ni multilayers and TiAl/TiC cermet joint was investigated. The layered structures consisting of a Ni 3 (AlTi) layer, a Ni 2 AlTi layer, a (Ni,Al,Ti) layer and a Ni diffusion layer were observed from the interlayer to the TiAl substrate. Only one AlNi 3 layer formed at the multilayer/TiC cermet interface. The reaction behaviour of Al/Ni multilayers was characterized by means of differential scanning calorimeter (DSC) and X-ray diffraction. The initial exothermic peak of the DSC curve was formed due to the formation of Al 3 Ni and Al 3 Ni 2 phases. The reaction sequence of the Al/Ni multilayers was Al 3 Ni → Al 3 Ni 2 → AlNi → AlNi 3 and the final products were AlNi and AlNi 3 phases. The shear strength of the joint was tested and the experimental results suggested that the application of Al/Ni multilayers improved the joining quality. - Highlights: ► Diffusion bonding of TiAl to TiC cermet was realized using Al/Ni multilayer. ► The reaction sequence of the Al/Ni multilayers was Al 3 Ni → Al 3 Ni 2 → AlNi → AlNi 3 . ► The interfacial microstructure of the joint was clarified. ► The application of Al/Ni multilayers improved the joining quality.

  15. Hot Corrosion Behavior of Stainless Steel with Al-Si/Al-Si-Cr Coating

    Science.gov (United States)

    Fu, Guangyan; Wu, Yongzhao; Liu, Qun; Li, Rongguang; Su, Yong

    2017-03-01

    The 1Cr18Ni9Ti stainless steel with Al-Si/Al-Si-Cr coatings is prepared by slurry process and vacuum diffusion, and the hot corrosion behavior of the stainless steel with/without the coatings is studied under the condition of Na2SO4 film at 950 °C in air. Results show that the corrosion kinetics of stainless steel, the stainless steel with Al-Si coating and the stainless steel with Al-Si-Cr coating follow parabolic laws in several segments. After 24 h corrosion, the sequence of the mass gain for the three alloys is the stainless steel with Al-Si-Cr coating coating coating. The corrosion products of the three alloys are layered. Thereinto, the corrosion products of stainless steel without coating are divided into two layers, where the outside layer contains a composite of Fe2O3 and FeO, and the inner layer is Cr2O3. The corrosion products of the stainless steel with Al-Si coating are also divided into two layers, of which the outside layer mainly consists of Cr2O3, and the inner layer is mainly SiO2. The corrosion film of the stainless steel with Al-Si-Cr coating is thin and dense, which combines well with substrate. Thereinto, the outside layer is mainly Cr2O3, and the inside layer is Al2O3. In the matrix of all of the three alloys, there exist small amount of sulfides. Continuous and protective films of Cr2O3, SiO2 and Al2O3 form on the surface of the stainless steel with Al-Si and Al-Si-Cr coatings, which prevent further oxidation or sulfide corrosion of matrix metals, and this is the main reason for the much smaller mass gain of the two alloys than that of the stainless steel without any coatings in the 24 h hot corrosion process.

  16. Gate length scaling effect on high-electron mobility transistors devices using AlGaN/GaN and AlInN/AlN/GaN heterostructures.

    Science.gov (United States)

    Liao, S Y; Lu, C C; Chang, T; Huang, C F; Cheng, C H; Chang, L B

    2014-08-01

    Compared to AlGaN/GaN HEMT with 0.15 μm T-gate length, the AlInN/AlN/GaN one exhibits much higher current density and transconductance of 1558 mA/mm at Vd = 2 V and 330 mS/mm, respectively. The high extrinsic ft and fmax of 82 GHz and 70 GHz are extracted from AlInN/AlN/GaN HEMT. Besides, we find that the transconductance roll-off is significant in AlGaN/GaN, but largely improved in AlInN/AlN/GaN HEMT, suggesting that the high carrier density and lattice-matched epitaxial heterostructure is important to reach both large RF output power and high operation frequency, especially for an aggressively gate length scaling.

  17. Some aspects of anelastic and microplastic creep of pure Al and two Al-alloys

    Energy Technology Data Exchange (ETDEWEB)

    Sgobba, S. (Lab. de Metallurgie Mecanique, Dept. des Materiaux, Ecole Polytechnique Federale de Lausanne (Switzerland)); Kuenzi, H.U. (Lab. de Metallurgie Mecanique, Dept. des Materiaux, Ecole Polytechnique Federale de Lausanne (Switzerland)); Ilschner, B. (Lab. de Metallurgie Mecanique, Dept. des Materiaux, Ecole Polytechnique Federale de Lausanne (Switzerland))

    1993-11-01

    Anelastic creep of pure Al, commercial Al-Cu and a binary Al-Cu alloy has been measured at room temperature by means of a high resolution laser interferometer. The irreversible component of the deformation was also quantified from measurements of the anelastic creep recovery. The dependence of the deformation-time curves on thermal treatment and cold work is analyzed. The mechanisms responsible for the room temperature anelastic creep are discussed. Materials loaded below their elastic limit can present either a pure anelastic behavior (commercial Al-Cu) or additional viscoelastic creep (pure Al, high purity Al-Cu). For commercial Al-Cu, the presence of an irreversible deformation appears to be mainly related to the state of the surface. A viscoelastic after effect has been measured for this alloy after a Cu-electroplating treatment. As a typical result for room temperature creep, the irreversible deformation depends logarithmically on load time. (orig.).

  18. Some aspects of anelastic and microplastic creep of pure Al and two Al-alloys

    International Nuclear Information System (INIS)

    Sgobba, S.; Kuenzi, H.U.; Ilschner, B.

    1993-01-01

    Anelastic creep of pure Al, commercial Al-Cu and a binary Al-Cu alloy has been measured at room temperature by means of a high resolution laser interferometer. The irreversible component of the deformation was also quantified from measurements of the anelastic creep recovery. The dependence of the deformation-time curves on thermal treatment and cold work is analyzed. The mechanisms responsible for the room temperature anelastic creep are discussed. Materials loaded below their elastic limit can present either a pure anelastic behavior (commercial Al-Cu) or additional viscoelastic creep (pure Al, high purity Al-Cu). For commercial Al-Cu, the presence of an irreversible deformation appears to be mainly related to the state of the surface. A viscoelastic after effect has been measured for this alloy after a Cu-electroplating treatment. As a typical result for room temperature creep, the irreversible deformation depends logarithmically on load time. (orig.)

  19. A study of ion damage in Al, Al/Cu and Al/Ag

    International Nuclear Information System (INIS)

    Marikar, P.

    1979-06-01

    Specimens of pure aluminium, aluminium-copper and aluminium-silver have been irradiated with 20 keV helium ions and/or 100 keV aluminium ions and the nature of the damage assessed using transmission electron microscopy. Irradiation with 20 keV helium ions to a dose of 2.7 x 10 15 ions cm -2 results in the formation of interstitial loops and helium gas bubbles. The helium bubbles were detectable only after annealing at a high temperature following irradiation. When the helium preinjected aluminium specimens were irradiated with 100 keV Al + ions to a dose of 84 dpa at temperatures above 150 0 C, voids were observed to form. At a lower dose of 64 dpa, only a high density of dislocation loops was observed. Al-1 wt% Cu alloy containing partially coherent theta' precipitates resists void formation to a considerable extent, and Al-10 wt% Ag alloy containing coherent G.P. zones offers complete resistance to both dislocation loop nucleation and void formation. The experimental results are discussed in the light of the current theories of irradiation induced damage in metals. The importance of the dislocation-sink efficiency for point defects, the gaseous impurity and the alloying elements in determining void formation is highlighted. (author)

  20. Self pierce riveting in the car body construction; Stanznieten im Karosserieleichtbau

    Energy Technology Data Exchange (ETDEWEB)

    Ahlers-Hestermann, G. [Boellhoff GmbH, Bielefeld (Germany)

    1999-09-01

    As an alterantive to spotwelding, self pierce riveting becomes more and more important in light weight automotive body constructions. The difficulties or impossibility of spotwelding Aluminium and High Tensile Strength Steel or material mixtures accelerated this development. Even plastic material can be joined to metal. Important mechanical properties such as fatigue and crash behaviour are improved. Costs are at the same level. Two examples of body parts in aluminium (Audi A6 bonnet and BMW 3 series front end) are described. (orig.) [German] Als Alternative zum Punktschweissen setzt sich das Stanznieten mit Halbhohlniet im Karosserieleichtbau mehr und mehr durch. Mit diesem Verfahren koennen verschiedene Materialen mit bis zu vier Lagen sicher verbunden werden. Dieser Beitrag der Boellhoff GmbH stellt das Verfahren vor und berichtet ueber zwei Beispiele aus der Praxis. (orig.)

  1. Current problems arising from the new law relating to franchise duties; Aktuelle Probleme des neuen Konzessionsabgabenrechts

    Energy Technology Data Exchange (ETDEWEB)

    Becker, P.

    1996-12-31

    The contribution examines the advantages and drawbacks of the new ordinance in German law relating to payment of franchise duties. The ordinance may bring about new problems if abused as a means of bringing pressure to bear in negotiations for takeover of existing electric or gas supply systems by local governments. The author analyses the legitimation of such exploitation of the franchise duty and in this context the general legal framework. (orig./CB) [Deutsch] Der Beitrag untersucht Vor- und Nachteile der neuen Verordnung im Konzessionsabgabenrecht, die im Hinblick auf Auseinandersetzungen um die ``Ubernahme von Strom- oder Gasversorgungssystemen durch Gemeinden neue Probleme mit sich bringen koennte, wenn Konzessionsabgaben als Druckmittel eingesetzt werden. Der Autor analysiert die Zulaessigkeit eines derartigen Einsatzes und in diesem Zusammenhang auch die rechtliche Basis der Konzessionsabgaben. (orig./CB)

  2. Solar thermal power plants for the Mediterranean region: A chance for a new era in the field of electricity supply; Solarthermische Kraftwerke fuer den Mittelmeerraum: Chance fuer eine neue Aera der Elektrizitaetsversorgung

    Energy Technology Data Exchange (ETDEWEB)

    Nitsch, J [DLR, Stuttgart (Germany)

    1994-12-31

    One promising option for a really environmentally and climaticly friendly electricity supply is the erection of solar thermal power plants in regions of the earth with a considerably high solar irradiation. In this work the technical and economical chances for this technology are analysed and explanations are given as to which energetic and econmic marginal conditions must be created for a successful market introduction, which could already be initiated with several demonstration power plants. (orig.) [Deutsch] Eine der vielversprechenden Optionen fuer wirklich umwelt- und klimafreundliche Elektrizitaetsversorgung stellt der Bau solarthermischer Kraftwerke in den einstrahlungsreichen Regionen der Erde dar. Der Beitrag analysiert die technisch-oekonomischen Chancen dieser Technologie und zeigt auf, welche energiewirtschaftlichen Randbedingungen als Voraussetzung fuer eine erfolgreiche Markteinfuehrung geschaffen werden muessen, die schon jetzt mit einer Reihe von Demonstrationskraftwerken beginnen koennte. (orig.)

  3. Simulation of pendulum shock experiments on a passenger car front axle; Simulation von Pendelschlagversuchen an einer PKW-Vorderachse

    Energy Technology Data Exchange (ETDEWEB)

    Sporer, L.; Witt, R.; Muehlbauer, R. [BMW Group, Muenchen (Germany)

    2001-07-01

    The contribution describes the development and application of a method for simulating loads resulting from misuse on car body components. The development of the method and its validation by experiments are described, and its application in the development of the BMW-5 series is gone into. [German] Der Beitrag beschreibt die Entwicklung und Anwendung einer Methode zur Simulation von Missbrauchsbelastungen an Fahrwerkskomponenten. Im ersten Abschnitt ist die systematische Entstehung der Methode und die Absicherung der Simulationsergebnisse durch Ersatzversuche dargestellt. In den folgenden Abschnitten steht die Anwendung der Methode in der Fahrwerksentwicklung bei BMW am Beispiel der Vorderachse der aktuellen 5-er Baureihe im Vordergrund. Das Deformationsverhalten einzelner Lenker bzw. die Schadenskette an der gesamten Achse werden sowohl fuer den seitlichen, als auch fuer den frontalen Pendelschlag aufgezeigt. (orig.)

  4. Was ein Wort bedeutet, kann ein Satz nicht sagen: Zur Bedeutung der Terminologiearbeit für die Technische Kommunikation und das Fachtextübersetzen

    Directory of Open Access Journals (Sweden)

    Klaus-Dirk Schmitz

    2010-05-01

    Full Text Available Einleitung: Dieser Beitrag geht von einem Zitat des österreichisch-britischen Philosophen Ludwig Wittgenstein aus und bezeiht sich auf seine Aussagen über Wörter und Sätze. Zielsetzung: Analyse und Diskussion der Relevanz von WittgensteinsAussage für die Terminologiearbeit in der Technischen Kommunikation und beim Fachübersetzen. Methode: Kritische Analyse und Betrachtung. Ergebnis: Neben den terminologischen Grundbegriffen Begriff, Benennung und Gegenstand werden vor allem die Definition als Begriffsbeschreibung sowie die Kriterien zur Bildung von Benennungen untersucht. Schlussfolgerung: Das Zitat von Wittgenstein lässt viele Interpretationen zu. Für die Technische Kommunikation und das Fachübersetzen muss aber die Definition (Satz den Begriff hinter der Benennung (Wort erklären. Idealerweise ist aber die Benennung so transparent, dass dadurch schon die Begriffsklärung erfolgt.

  5. Music hall Markneukirchen; Musikhalle in Markneukirchen

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1996-01-01

    The article presents the new building of the music hall Markneukirchen. From the planned use of the building result very high demands on the ventilation system in order to keep to a sound power level of less than 30 dB(A) in the hall. The building services are dealt with using numerous flowsheets and diagrams: Heat supply, ventilation system, sanitary system, building management, instrumentation and control, electric and lighting systems. (BWI) [Deutsch] Der vorliegende Beitrag stellt den Neubau der Musikhalle Markneukirchen vor. Durch das Nutzungskonzept ergeben sich fuer die Einhaltung eines Schalleistungspegels von weniger als 30 dB(A) im Saalbereich an die Lueftungsanlage sehr hohe Ansprueche. Es werden die raumlufttechnischen Anlagen anhand zahlreicher Flussbilder und Abbildungen vorgestellt: Waermeversorgung, Lueftungstechnik, Sanitaertechnik, Gebaeudeleit- und MSR-Technik, Elektro- und Lichttechnik. (BWI)

  6. Kada parašytas vadinamasis Krauzės žodynas

    Directory of Open Access Journals (Sweden)

    Vincentas Drotvinas

    2011-12-01

    Full Text Available WANN WURDE DAS SOGENANNTE WÖRTERBUCH VON KRAUSE GESCHRIEBEN?ZusammenfassungDer Beitrag hat das Ziel, das Entstehungsdatum des sogenannten handschriftlichen deutsch-litauischen Wörterbuches von Krause nachzuprüfen. Bisher besteht die Meinung (J. Lebedys, daß dieses Wörterbuch im 17. Jh. geschrieben worden ist und sein Autor (oder der Besitzer Andreas Krause (gest. 1655 gewesen sein könnte. Mit Hilfe von Wasserzeichenanalyse haben wir aber fest­gestellt, daß das Wörterbuch auf Papier der Papiermühle von Johann Wilhelm Steinmetz (1720— 1749, ehem. Ostpreußen geschrieben worden ist. Da nicht Andreas Krause der Autor dieses Wör­terbuches gewesen sein konnte, müßte man das erwähnte Wörterbuch weiterhin als anonym betrach­ten.

  7. Dimensioning and design rules for sliding bearings; optimisation problems; Bemessungs- und Gestaltungsregeln fuer Gleitlager: Optimierungsfragen

    Energy Technology Data Exchange (ETDEWEB)

    Spiegel, K. [Fachhochschule Duesseldorf (Germany); Fricke, J.

    2000-07-01

    Already in the design stage of sliding bearings, optimal conditions for operation at a later stage should be envisaged. The contribution presents hints for optimal design and calculation of radial and axial bearings, e.g. gap design, optimised supporting strength, friction loss and lubricant throughput, lubricant exchange and lubricant heat exchange, and improved control of internal lubricant flow. [German] Bei der Auslegung von Gleitlagern ist es von Interesse, moeglichst optimale Bedingungen fuer den spaeteren Betrieb zu schaffen. Im vorliegenden Beitrag werden einige bereits bekannte und auch neue Hinweise zur optimalen Gestaltung und Berechnung, sowohl fuer Radial- als auch Axiallager gegeben. Dies betreffen im wesentlichen: die Gestaltung des Spaltverlaufs, Empfehlungen zur Optimierung der Tragfaehigkeit, der Reibungsverluste und des Schmierstoffdurchsatzes, Hinweise zum Schmierstoff- bzw. Schmierstoff-Waermeaustausch und die Verbesserung der inneren Schmierstofffuehrung. (orig.)

  8. Interdiffusion between U(Mo,Pt) or U(Mo,Zr) and Al or Al A356 alloy

    International Nuclear Information System (INIS)

    Komar Varela, C.; Mirandou, M.; Arico, S.; Balart, S.; Gribaudo, L.

    2009-01-01

    Solid state reactions in chemical diffusion couples U-7 wt.%Mo-0.9 wt.%Pt/Al at 580 deg. C and U-7 wt.%Mo-0.9 wt.%Pt/Al A356 alloy, U-7 wt.%Mo-1 wt.%Zr/Al and U-7 wt.%Mo-1 wt.%Zr/Al A356 alloy at 550 deg. C were characterized. Results were obtained from optical and scanning electron microscopy, electron probe microanalysis and X-ray diffraction. The UAl 3, UAl 4 and Al 20 Mo 2 U phases were identified in the interaction layers of γU(Mo,Pt)/Al and γU(Mo,Zr)/Al diffusion couples. Al 43 Mo 4 U 6 ternary compound was also identified in γU(Mo,Zr)/Al due to the decomposition of γU(Mo,Zr) phase. The U(Al,Si) 3 and U 3 Si 5 phases were identified in the interaction layers of γU(Mo,Pt)/Al A356 and γU(Mo,Zr)/Al A356 diffusion couples. These phases are formed due to the migration of Si to the interaction layer. In the diffusion couple U(Mo,Zr)/Al A356, Zr 5 Al 3 phase was also identified in the interaction layer. The use of synchrotron radiation at Brazilian Synchrotron Light Laboratory (LNLS, CNPq, Campinas, Brazil) was necessary to achieve a complete crystallographic characterization.

  9. CuAlO2 and CuAl2O4 thin films obtained by stacking Cu and Al films using physical vapor deposition

    Science.gov (United States)

    Castillo-Hernández, G.; Mayén-Hernández, S.; Castaño-Tostado, E.; DeMoure-Flores, F.; Campos-González, E.; Martínez-Alonso, C.; Santos-Cruz, J.

    2018-06-01

    CuAlO2 and CuAl2O4 thin films were synthesized by the deposition of the precursor metals using the physical vapor deposition technique and subsequent annealing. Annealing was carried out for 4-6 h in open and nitrogen atmospheres respectively at temperatures of 900-1000 °C with control of heating and cooling ramps. The band gap measurements ranged from 3.3 to 4.5 eV. Electrical properties were measured using the van der Pauw technique. The preferred orientations of CuAlO2 and CuAl2O4 were found to be along the (1 1 2) and (3 1 1) planes, respectively. The phase percentages were quantified using a Rietveld refinement simulation and the energy dispersive X-ray spectroscopy indicated that the composition is very close to the stoichiometry of CuAlO2 samples and with excess of aluminum and deficiency of copper for CuAl2O4 respectively. High resolution transmission electron microscopy identified the principal planes in CuAlO2 and in CuAl2O4. Higher purities were achieved in nitrogen atmosphere with the control of the cooling ramps.

  10. Three-Dimensional FIB/EBSD Characterization of Irradiated HfAl3-Al Composite

    Energy Technology Data Exchange (ETDEWEB)

    Hua, Zilong; Guillen, Donna Post; Harris, William; Ban, Heng

    2016-09-01

    A thermal neutron absorbing material, comprised of 28.4 vol% HfAl3 in an Al matrix, was developed to serve as a conductively cooled thermal neutron filter to enable fast flux materials and fuels testing in a pressurized water reactor. In order to observe the microstructural change of the HfAl3-Al composite due to neutron irradiation, an EBSD-FIB characterization approach is developed and presented in this paper. Using the focused ion beam (FIB), the sample was fabricated to 25µm × 25µm × 20 µm and mounted on the grid. A series of operations were carried out repetitively on the sample top surface to prepare it for scanning electron microscopy (SEM). First, a ~100-nm layer was removed by high voltage FIB milling. Then, several cleaning passes were performed on the newly exposed surface using low voltage FIB milling to improve the SEM image quality. Last, the surface was scanned by Electron Backscattering Diffraction (EBSD) to obtain the two-dimensional image. After 50 to 100 two-dimensional images were collected, the images were stacked to reconstruct a three-dimensional model using DREAM.3D software. Two such reconstructed three-dimensional models were obtained from samples of the original and post-irradiation HfAl3-Al composite respectively, from which the most significant microstructural change caused by neutron irradiation apparently is the size reduction of both HfAl3 and Al grains. The possible reason is the thermal expansion and related thermal strain from the thermal neutron absorption. This technique can be applied to three-dimensional microstructure characterization of irradiated materials.

  11. Digitalisierung und Energie 4.0 - Wie schaffen wir die digitale Energiewende?

    Science.gov (United States)

    Irlbeck, Maximilian

    Die digitale Energiewende verändert nachhaltig die Systeme der "alten" Energiewelt. Ein Zusammenwachsen verschiedener Domänen im Energiesystem, die durch digitale Technologie möglich wird, birgt enorme Herausforderungen, ist aber notwendig, um die Energiewende und ihre Ziele zu meistern. Dieser Beitrag beschreibt die Wirkung der Digitalisierung auf das Energiesystem, listet Charakteristika der digitalen Energiewende auf und schildert für verschiedene Domänen mögliche Zielvorstellungen, die durch digitale Technologie umsetzbar sind. Am Ende erläutert der Beitrag Handlungsschritte, die auf dem Weg zu einem erneuerbaren Energiesystem gegangen werden sollten und zeigt Probleme und Risiken einer Fehlentwicklung auf.

  12. Ex-ante Evaluation von Investitionsalternativen

    Directory of Open Access Journals (Sweden)

    Matthias Müller

    2017-12-01

    Full Text Available Der Beitrag zeigt, wie mit Hilfe der Methode der agentenbasierten Modellierung und Simulation (ABMS ein Beitrag zur ex-ante Policy-Beratung geleistet werden kann. Anhand eines exemplarischen Anwendungsfalls, der VISIBLE Simulationsumgebung („Virtual Simulation Lab for the Analysis of Investments in Learning and Education“, diskutieren wir die Konsequenzen unterschiedlicher Kooperationsförderinstrumente für Wissensdiffusionsprozesse in Netzwerken am Beispiel der Region Heilbronn-Franken. Die Simulationsergebnisse zeigen, dass die strukturelle Konfiguration eines regionalen Innovationssystems eine zentrale Bedeutung für die Gestaltung von Kooperationsfördermaßnahmen hat und dass Interventionen, die darauf abzielen, Wissenstransfer zwischen den Akteuren anzuregen, genau die entgegengesetzten Wirkungen entfalten können.

  13. The Genyornis Egg: Response to Miller et al.'s commentary on Grellet-Tinner et al., 2016

    Science.gov (United States)

    Grellet-Tinner, Gerald; Spooner, Nigel A.; Handley, Warren D.; Worthy, Trevor H.

    2017-04-01

    Williams (1981) and Williams and Rich (1991) attributed Australian Quaternary fossil eggshell that differed from that of emu Dromaius novaehollandiae to the extinct bird Genyornis newtoni without any osteological or embryonic support. Such association by proximity or abundance mirrors the case of the mistaken association of oviraptor eggs to Protoceratops in the 1920's by Andrews (Grellet-Tinner and Makovicky, 2006). No other candidate species was considered, and this attribution has been unchallenged and followed by everyone thereafter. Much research has been done on this Australian eggshell, with one result being that the extinction of the parent of this eggshell is the most well documented for a taxon in Australia (e.g., Miller et al., 1999, 2005). Grellet-Tinner et al. (2016) raised several problems with the identity of the eggshell Williams (1981) attributed to Genyornis newtoni and suggested that extinct megapodes of the genus Progura were the more likely layer of this eggshell type, therein referred to as ;putative Genyornis oological material; (PGOM). Miller et al. (2017) challenged our hypothesis stating that ;Based on the dimensions of the reconstructed Spooner Egg,Grellet-Tinner et al. (2016)argue that PGOM is too small for a bird with the body mass estimated for Genyornis (168-275 kg) … …[and] …. None of the additional PGOM observations reported byGrellet-Tinner et al. (2016)are inconsistent with a Genyornis parent;. Here we take the opportunity to respond to their critique, the basis of which resolves into a few points, which we address in turn.

  14. Characterization of Al/Ni multilayers and their application in diffusion bonding of TiAl to TiC cermet

    Energy Technology Data Exchange (ETDEWEB)

    Cao, J., E-mail: cao_jian@hit.edu.cn [State Key Lab of Advanced Welding Production Technology, Harbin Institute of Technology, Harbin, 150001 (China); Center for Composite Materials and Structures, Harbin Institute of Technology, Harbin, 150001 (China); Song, X.G. [State Key Lab of Advanced Welding Production Technology, Harbin Institute of Technology, Harbin, 150001 (China); Wu, L.Z. [Center for Composite Materials and Structures, Harbin Institute of Technology, Harbin, 150001 (China); Qi, J.L.; Feng, J.C. [State Key Lab of Advanced Welding Production Technology, Harbin Institute of Technology, Harbin, 150001 (China)

    2012-02-29

    The Al/Ni multilayers were characterized and diffusion bonding of TiAl intermetallics to TiC cermets was carried out using the multilayers. The microstructure of Al/Ni multilayers and TiAl/TiC cermet joint was investigated. The layered structures consisting of a Ni{sub 3}(AlTi) layer, a Ni{sub 2}AlTi layer, a (Ni,Al,Ti) layer and a Ni diffusion layer were observed from the interlayer to the TiAl substrate. Only one AlNi{sub 3} layer formed at the multilayer/TiC cermet interface. The reaction behaviour of Al/Ni multilayers was characterized by means of differential scanning calorimeter (DSC) and X-ray diffraction. The initial exothermic peak of the DSC curve was formed due to the formation of Al{sub 3}Ni and Al{sub 3}Ni{sub 2} phases. The reaction sequence of the Al/Ni multilayers was Al{sub 3}Ni {yields} Al{sub 3}Ni{sub 2} {yields} AlNi {yields} AlNi{sub 3} and the final products were AlNi and AlNi{sub 3} phases. The shear strength of the joint was tested and the experimental results suggested that the application of Al/Ni multilayers improved the joining quality. - Highlights: Black-Right-Pointing-Pointer Diffusion bonding of TiAl to TiC cermet was realized using Al/Ni multilayer. Black-Right-Pointing-Pointer The reaction sequence of the Al/Ni multilayers was Al{sub 3}Ni {yields} Al{sub 3}Ni{sub 2} {yields} AlNi {yields} AlNi{sub 3}. Black-Right-Pointing-Pointer The interfacial microstructure of the joint was clarified. Black-Right-Pointing-Pointer The application of Al/Ni multilayers improved the joining quality.

  15. UNDERSTANDING THE MULTIDIMENSIONAL ISLAMIC FAITH THROUGH ‘ABD AL-GHANI AL-NABULUSI’S MYSTICAL PHILOSOPHY

    Directory of Open Access Journals (Sweden)

    Naoki Yamamoto

    2013-12-01

    Full Text Available This paper tries to present a new perspective on Islamic faith and Muslim identity to Muslim minorities who are challenged in practicing or following Islamic law in non-Islamic countries or non-Muslims in the contemporary world. It will uncover the multidimensional perspective of the concept of faith based on sin (dhanb and repentance (tawbah through the mystical philosophy of a Syrian scholar, Abd al-Ghani al-Nabulusi (d. 1143/1741 of the 18th century Ottoman Damascus who contributed to the field of Sufism particularly based on Ibn ‘Arabi’s thought of wahdat al-wujud (oneness of being and insan kamil (the perfect man. Nabulusi believes that anyone who lived during the inexistence of prophet’s revelation, inhabited an isolated place cut off from information about Islam, or lived in dar al-harb and did not make a hijra to dar al-islam could not be regarded as sinful in their deeds. However, faith in Allah is essential and infidelity is not forgiven regardless whether or not they live in dar al-islam or dar al-harb. Further, Nabulusi insists that true faith can be achieved by understanding the sin of existence; the ignorance of the difference of existence between Allah and men.  [Artikel ini menjelaskan identitas keberagamaan umat Islam minoritas yang dituntut untuk menerapkan syariat, namun harus hidup di negara non-muslim, dengan mendiskusikan perspektif multidimensional terhadap konsep dosa dan tobat seperti dikembangkan oleh Abd al-Ghanī al-Nabulusī (1143/1741, seorang sufi pemikir Syria, khususnya  wahdat al-wujūd dan insan kamil, yang hidup di masa kesultanan Usmani di Damaskus. Nabulusī berkeyakinan bahwa siapa saja yang hidup sebelum turunnya wahyu di masa Nabi, hidup di daerah terpencil yang tidak mengenal Islam, atau hidup di dar al-harb dan tidak hijrah ke dar al-islam, tidaklah dibebani dosa atas perbuatannya. Namun demikian, iman kepada Allah amatlah penting dan kekufuran tidaklah dimaafkan, baik seseorang tersebut hidup

  16. PRECIPITATION HARDENING IN B2-ORDERED NiAl BY Ni2AlTiCOMPOUND

    Institute of Scientific and Technical Information of China (English)

    W.H. Tian; K. Ohishi; M. Nemoto

    2001-01-01

    Microstructural variations and correlated hardness changes in B2-ordered NiAl containing fine precipitation of Ni2AlTi have been investigated by means of transmission electron microscopy (TEM) and hardness tests. The amount of age hardening is not large as compared to the large microstructural variations during aging. TEM observations have revealed that the L21-type Ni2AlTi precipitates keep a lattice coherency with the NiAl matrix at the beginning of aging. By longer periods of aging Ni2AlTi precipitates lose their coherency and change their morphology to the globular ones surrounded by misfit dislocations. The temperature dependence of the yield strength of precipitate-containing B2-ordered NiAl was investigated by compression tests over the temperature range of 873-1273K. The fine precipitation of Ni2AlTi was found to enhance greatly the yield strength and the high-temperature strength is comparison with that of superalloy Mar-M200.``

  17. Rupture of Al matrix in U-Mo/Al dispersion fuel by fission induced creep

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Gwan Yoon; Sohn, Dong Seong [UNIST, Daejeon (Korea, Republic of); Kim, Yeon Soo [Argonne National Laboratory, Argonnge (United States); Lee, Kyu Hong [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    This phenomenon was found specifically in the dispersion fuel plate with Si addition in the Al matrix to suppress interaction layer (IL) formation between UMo and Al. It is known that the stresses induced by fission induced swelling in U-Mo fuel particles are relieved by creep deformation of the IL, surrounding the fuel particles, that has a much higher creep rate than the Al matrix. Thus, when IL growth is suppressed, the stress is instead exerted on the Al matrix. The observed rupture in the Al matrix is believed to be caused when the stress exceeded the rupture strength of the Al matrix. In this study, the possibility of creep rupture of the Al matrix between the neighboring U-Mo fuel particles was examined using the ABAQUS finite element analysis (FEA) tool. The predicted rupture time for a plate was much shorter than its irradiation life indicating a rupture during the irradiation. The higher stress leads Al matrix to early creep rupture in this plate for which the Al matrix with lower creep strain rate does not effectively relieve the stress caused by the swelling of the U-Mo fuel particles. For the other plate, no rupture was predicted for the given irradiation condition. The effect of creeping of the continuous phase on the state of stress is significant.

  18. Des Widerspenstigen Zähmung: Subjektives Alter(n, qualitativ erforscht

    Directory of Open Access Journals (Sweden)

    Stefanie Graefe

    2013-04-01

    Full Text Available Der Beitrag präsentiert Forschungsergebnisse einer qualitativen Interviewstudie zur subjektiven Alter(nserfahrung von Menschen in der zweiten Lebenshälfte sowie aus dem Forschungsprozess resultierende Überlegungen zur Frage, wie sich die soziale Erfahrung Alter(n methodologisch konzeptualisieren und empirisch erforschen lässt. Die Auswertung erfolgte angelehnt an die Grounded-Theory- Methodologie. Ausgehend von der "relativen (subjektiven Alterslosigkeit" als fallübergreifender Schlüsselkategorie wird im Folgenden eine Typologie von (Alters- Selbstkonzepten vorgestellt: das "wandlungsfähige", das "kontinuierliche" und das "verunsicherte" (Alters- Selbst. Skizziert wird eine methodologische Konzeption von Alter(n als eine zugleich prinzipiell unscharfe und erheblich normierte soziale Kategorie. Die Ergebnisse der Studie deuten darauf hin, dass – insbesondere vor dem Hintergrund der in jüngerer Zeit erfolgten sozialpolitischen Aufwertung der Lebensphase Alter – spezifische Sozialmilieus besonders prädestiniert scheinen, normative Anforderungen einer aktiven, produktiven und selbstverantwortlichen Gestaltung der Lebensphase Alter in ihr Selbstkonzept zu integrieren. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1302114

  19. Urbanität nach exklusivem Rezept. Die Ausdeutung des Städtischen durch hochpreisige Immobilienprojekte in Berlin und Los Angeles

    Directory of Open Access Journals (Sweden)

    Henning Füller

    2013-07-01

    Full Text Available Innerstädtisches Wohnen steht zunehmend hoch im Kurs. Wahlweise als „Renaissance der Stadt“, Reurbanisierung oder Gentrifizierung thematisiert, ist das gegenwärtige Interesse von Investor_innen, Projektentwickler_innen und Käufer_innen an innerstädtischen Lagen prägnanter Ausdruck einer fortgesetzten Restrukturierung europäischer und US-amerikanischer Städte. Neben Prozessen der Inwertsetzung und Verdrängung umfasst diese Neuordnung auch die Ebene der Bedeutungen von Stadt und Urbanität. Insbesondere hochpreisige Neubauprojekte konkretisieren derzeit veränderte Vorstellungen bezüglich der Qualität der Stadt, ihrer Nutzer_innen und Nutzungsweisen. Der Beitrag zieht Projekte innerstädtischen Luxuswohnens in Berlin und Los Angeles heran, um dieser baulichen Konkretisierung von Diskursen um Stadt und Urbanität als Aspekt der gegenwärtigen „Renaissance der Stadt“ nachzugehen. In welcher Weise manifestieren sich Vorstellungen des erstrebenswerten städtischen Lebens in aktuellen Projekten hochpreisigen innerstädtischen Wohnungsbaus und welche Implikationen hat dies für die Gestalt der Stadt?

  20. ‹Portale›, die zum Nachdenken anregen. Einblicke in eine Interfaceanalyse des Augmented Reality Spiels Ingress

    Directory of Open Access Journals (Sweden)

    Franco Rau

    2017-02-01

    Full Text Available Augmented Reality Spiele wie ‹Ingress› und ‹PokémonGo› stellen aktuell neue mediale Phänomene dar. Eine zentrale Differenz zu klassischen Massively Multiplayer Online Games (MMOs ist die Verzahnung von virtuellen und realen Objekten als konstitutive Spielelemente. In Anknüpfung an die Perspektive, digitale Spiele als Kultur- und Bildungsräume zu verstehen, widmet sich der Beitrag der Frage, inwiefern das Ingress-Spielen die Perspektive von Spieler/innen auf den öffentlichen Raum verändern kann. In erster Annäherung an diese Fragestellung wird auf Basis einer Interfaceanalyse gezeigt, wie ‹Portale› – virtueller Repräsentationen realer Objekte im Spiel – potenziell Irritationen und Differenz­erfahrungen ermöglichen. Diese können zum Ausgangspunkt weiterführender Reflexionen werden. Dafür werden exemplarisch ‹Portale› diskutiert, die (1. weiterführende Informationen zu realen Objekte bieten, die (2. Momentaufnahmen nicht mehr existierender kultureller Objekte darstellen und die (3. reale Objekte in ironischer Weise präsentieren.

  1. Poznaniu predchádza porozumenie (Der Erkenntnis geht das Verständnis voran

    Directory of Open Access Journals (Sweden)

    Jana Tomašovičová

    2007-12-01

    Full Text Available In diesem Beitrag deuten wir nach der Parmenides Inspiration zwei Wege der menschlichen Wanderung zur Wahrheit an. In Denkensgeschichte war ein Weg der begründeten Erkenntnis bevorzugt, auf dem wir gerade das aussuchen, was als haltbar im Änderungsprozess überdauert. Auf diesem Weg können wir ein souveränes denkendes Subjekt treffen, das wegen seiner Rationalität ein fester Grund beim Erkennen der Welt geworden ist. Am Anfang des 20. Jahrhunderts hat Martin Heidegger darauf hingewiesen, dass im altäglichen Leben unserer Erkenntnis das Verständnis dessen vorangeht, was wir besorgen. Heidegger hat also einen anderen Weg auserwählt, auf dem er bemerkt, dass für einen Mensch eher als seine Rationalität das Abfinden mit seiner faktischen Existenz charakteristisch ist. Heideggers Dasein ist nicht mehr ein Souverän, sondern eine Existenz, die sich um Seinsverständnis bemüht. Ungefähr ab 1930 finden wir eine Kehre im Heideggers Denken. Er sucht einen neuen Weg, auf dem er eine Ek-sistenz vorstellen will.

  2. "Doing pupil" nach Schulschluss – Videografie an einer Kinderuniversität

    Directory of Open Access Journals (Sweden)

    Alexandra König

    2015-03-01

    Full Text Available Auf der Basis einer Videografie an einer Kinderuniversität wird in dem vorliegenden Beitrag die Frage verfolgt, wie an einem außerschulischen Lernort generationale Ordnung hergestellt wird und welche Gestalt diese annimmt. Als heuristischer Rahmen dient das Modell der "Sozialisation als generationales Ordnen" (BÜHLER-NIEDERBERGER 2011; BÜHLER-NIEDERBERGER & TÜRKYILMAZ 2014. Die Analyse der ersten Sitzungen von zwei kontrastiven Kursen an der Kinder- und Jugenduniversität zeigt erstens, wie Kinder struktursensitiv Regeln in dem unbekannten Kontext erspüren, erarbeiten und modifizieren, wie sie KomplizInnen in der Herstellung generationaler Ordnung sind. Zweitens wird die Dominanz der schulischen Ordnung und des SchülerInnenstatus für Kindheit deutlich. Die Kinder stellen "Schule" her – paradoxerweise auch in einem außerschulischen Kontext. Drittens wird im kontrastiven Vergleich der untersuchten Kurse eine Varianz dieser Ordnungen – in Bezug auf die Form des Wissens und Adressierung der Kinder – herausgearbeitet, die allerdings die Dominanz der schulischen Ordnung nicht bricht. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs150263

  3. Ideologiekritik des E-Learnings. Welchen Nutzen hat die Einführung von E-Learning?

    Directory of Open Access Journals (Sweden)

    Katharina Kaiser-Müller

    2015-03-01

    Full Text Available Vor etwa sieben Jahren hat das damalige Bundesministerium für Unterricht, Kunst und Kultur (bm:ukk, das seit 2014 Bundesministerium für Bildung und Frauen (BMBF genannt wird, verschiedene Maßnahmen im Blick auf neuen Medien – insbesondere im Blick auf das E-Learning – gesetzt, um einen Beitrag zur Vorbereitung der Lernenden auf eine Informations- und Wissensgesellschaft zu leisten. E-Learning wurde als Erfolgsfaktor für die Zukunft gesehen und mit der Begründung, es fördere das individuelle und selbst gesteuerte Lernen, gefördert. Die zentrale Frage ist dabei: Welchen Nutzen hat die Einführung von E-Learning? In diesem Artikel wird dahingehend aufgezeigt, dass E-Learning nicht wegen pädagogischem Bedarf, sondern durch ministeriell gesetzte Maßnahmen eingeführt wurde und dadurch – wenn auch nicht bewusst und schon gar nicht als solches kommuniziert – neoliberale Strukturen durchgesetzt wurden. Die Einführung von E-Learning hat somit für deren Akzeptanz gesorgt.

  4. Effect of Al and AlP on the microstructure of Mn-30 wt.%Si alloy

    Energy Technology Data Exchange (ETDEWEB)

    Wu Yuying [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jing Shi Road 73, Jinan 250061 (China); Liu Xiangfa [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jing Shi Road 73, Jinan 250061 (China)], E-mail: xfliu@sdu.edu.cn

    2008-04-15

    Effect of Al and AlP particles on the microstructure of near eutectic Mn-Si alloy (Mn-30 wt.%Si) was studied by Electron Probe Micro-analyzer (EPMA) and Differential Scanning Calorimeter (DSC). Crystal lattice correspondence analyses show that both Al and AlP have good lattice matching coherence relationships with MnSi phase, and the addition of Al and AlP particles results in an abnormal eutectic structure, i.e. the eutectic constitution MnSi and Mn{sub 5}Si{sub 3} precipitate separately: MnSi precipitates firstly, and then the Mn{sub 5}Si{sub 3} phase.

  5. Elastocaloric effect in CuAlZn and CuAlMn shape memory alloys under compression

    OpenAIRE

    Qian, Suxin; Geng, Yunlong; Wang, Yi; Pillsbury, Thomas E.; Hada, Yoshiharu; Yamaguchi, Yuki; Fujimoto, Kenjiro; Hwang, Yunho; Radermacher, Reinhard; Cui, Jun; Yuki, Yoji; Toyotake, Koutaro; Takeuchi, Ichiro

    2016-01-01

    This paper reports the elastocaloric effect of two Cu-based shape memory alloys: Cu68Al16Zn16 (CuAlZn) and Cu73Al15Mn12 (CuAlMn), under compression at ambient temperature. The compression tests were conducted at two different rates to approach isothermal and adiabatic conditions. Upon unloading at a strain rate of 0.1 s−1 (adiabatic condition) from 4% strain, the highest adiabatic temperature changes (ΔTad) of 4.0 K for CuAlZn and 3.9 K for CuAlMn were obtained. The maximum stress and hystere...

  6. Formation of Al3Ti/Mg composite by powder metallurgy of Mg-Al-Ti system.

    Science.gov (United States)

    Yang, Zi R; Qi Wang, Shu; Cui, Xiang H; Zhao, Yu T; Gao, Ming J; Wei, Min X

    2008-07-01

    An in situ titanium trialuminide (Al 3 Ti)-particle-reinforced magnesium matrix composite has been successfully fabricated by the powder metallurgy of a Mg-Al-Ti system. The reaction processes and formation mechanism for synthesizing the composite were studied by differential scanning calorimetry (DSC), x-ray diffractometry (XRD), scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDS). Al 3 Ti particles are found to be synthesized in situ in the Mg alloy matrix. During the reaction sintering of the Mg-Al-Ti system, Al 3 Ti particles are formed through the reaction of liquid Al with as-dissolved Ti around the Ti particles. The formed intermetallic particles accumulate at the original sites of the Ti particles. As sintering time increases, the accumulated intermetallic particles disperse and reach a relatively homogeneous distribution in the matrix. It is found that the reaction process of the Mg-Al-Ti system is almost the same as that of the Al-Ti system. Mg also acts as a catalytic agent and a diluent in the reactions and shifts the reactions of Al and Ti to lower temperatures. An additional amount of Al is required for eliminating residual Ti and solid-solution strengthening of the Mg matrix.

  7. Al-‘Alāqah baina Ushūl al-Fiqh wa Maqāshidi al-Sharīah wa al-Da’wah ilā Ta’sīsi ‘Ilmi al-Maqāshid

    Directory of Open Access Journals (Sweden)

    Anggraini Binti Ramli

    2016-12-01

    Full Text Available The study of Maqāshid sharīa is an important point in the discussion of Islamic legal theory (ushūl al-fiqh. Serious debates began to emerge in the 19th century among Islamic jurists concerning the position of maqāshid sharīa. At least, there are three important debates in the history; first, whether maqāshid is part of the discussion ushūl al-fiqh; second, is maqāshid sharīa built upon a foundation of classical Islamic jurisprudence (fiqh; and third, whether the maqāshid sharīa study is able to become an independent science that is separated from the study of classical Islamic jurisprudence. This article tries to present a discussion of the three paradigms by employing a descriptive-analytic method. The results of this study uncover that the study of maqāshid sharīa is like two sides of one coin; theoretically it is a distinctive study from ushūl al-fiqh, but it cannot be separated from one another. Ushūl al-fiqh has become the foundation to find out more details about the study of maqashid sharia. The separation between classical Islamic jurisprudence (fiqh and maqāshid sharīa study conducted by Islamic jurists is a relative separation.

  8. Solutional Landforms of Gabal Al-Qaraha, the Oasis of Al-Hasa, Saudi Arabia

    OpenAIRE

    Embabi, Nabil S.

    1981-01-01

    Jabal Al-Qarah is one of the small outlier hills at the Oasis of Al-Hasa, lying at about lOkm ENE of Al-Hafuf Town. The solutional forms of Al-Qarah hill discussed in this paper are as follows : 1. A calcareous duricrust which covers the top and some of the slopes of the hill. 2. Rock Pillars which are long columns of white lime-stone. 3. Huge crevasses which are wide erosional openings along vertical joints. 4. Narrow, sinuous caves inside the hill. 5. Pedestal rocks with mushroo...

  9. Comparison on the interaction of Al3+/nano-Al13 with calf thymus DNA /salmon sperm DNA

    Science.gov (United States)

    Ma, Fei; Ma, Yue; Du, Changwen; Yang, Xiaodi; Shen, Renfang

    2015-11-01

    The conformation change, binding mode and binding site between Al3+/nano-Al13 and calf thymus DNA/salmon sperm DNA were investigated by UV-vis absorption, FTIR spectra, Raman spectroscopy and CD spectra, as well as melting curves measurement. The UV-vis spectra and circular dichroism spectra results suggested that the phosphate group structure was changed when Al3+ interacted with DNA, while the double-helix was distorted when nano-Al13 interacted with DNA. The FTIR and Raman spectroscopy revealed that the binding sites were Al3+ … PO2, Al3+ … N7/guanine PO2 … Al13 … N7-C8/guanine with calf thymus DNA, and Al3+ … N3-O2/cytosine, Al3+ … N7-C8/guanine, PO2 … Al13 … N7-C8/guanine, PO2 … Al13 … N1/adenine with salmon sperm DNA, respectively. The electrostatic binding was existed between Al3+ and DNA, and the electrostatic binding and complexing were found between nano-Al13 and DNA.

  10. Bukti Kebenaran Al-quran

    OpenAIRE

    Aliyah, Sri

    2015-01-01

    Al Quran is the greatest miracles of Muhammad SAW as the direction of humankind in order to reach eternal happiness. Scientific evidences show that Al Quran has the truth massages, although it was released far before the finding of modern sciences. The researches continue to study the truth of Al Quran an it revealed the historical fact.

  11. Sintering of (Ni,Mg)(Al,Fe)2O4 Materials and their Corrosion Process in Na3AlF6-AlF3-K3AlF6 Electrolyte

    Science.gov (United States)

    Xu, Yibiao; Li, Yawei; Yang, Jianhong; Sang, Shaobai; Wang, Qinghu

    2017-06-01

    The application of ledge-free sidewalls in the Hall-Héroult cells can potentially reduce the energy requirement of aluminum production by about 30 pct (Nightingale et al. in J Eur Ceram, 33:2761-2765, 2013). However, this approach poses great material challenges since such sidewalls are in direct contact with corrosive electrolyte. In the present paper, (Ni,Mg)(Al,Fe)2O4 materials were prepared using fused magnesia, reactive alumina, nickel oxide, and iron oxide powders as the starting materials. The sintering behaviors of specimens as well as their corrosion resistance to molten electrolyte have been investigated by means of X-ray diffraction and scanning electron microscope. The results show that after firing at temperature ranging from 1673 K (1400 °C) up to 1873 K (1600 °C), all the specimens prepared are composed of single-phase (Ni,Mg)(Al,Fe)2O4 composite spinel, the lattice parameter of which increases with increasing Fe3+ ion concentration. Increasing the iron oxide content enhances densification of the specimens, which is accompanied by the formation of homogeneously distributed smaller pores in the matrix. The corrosion tests show that corrosion layers consist of fluoride and Ni(Al,Fe)2O4 composite spinel grains are produced in specimens with Fe/Al mole ratio no more than 1, whereas dense Ni(Al,Fe)2O4 composite spinel layers are formed on the surface of the specimens with Fe/Al mole ratio more than 1. The dense Ni(Al,Fe)2O4 composite spinel layers formed improve the corrosion resistance of the specimens by inhibiting the infiltration of electrolyte and hindering the chemical reaction between the specimen and electrolyte.

  12. Synthesis of Al(OH3 Nanostructures from Al(OH3 Microagglomerates via Dissolution-Precipitation Route

    Directory of Open Access Journals (Sweden)

    Bo Yu

    2013-01-01

    Full Text Available A facile method was developed to synthesize Al(OH3 nanostructures from Al(OH3 microagglomerates by dissolution in 9.0 mol·L−1 NaOH at 115°C followed by dilution and aging of the solution at room temperature. The influence of Al(OH3 nanoseed and surfactants as sodium dodecyl sulfate (SDS, polyethylene glycol 6000 (PEG6000, and cetyltrimethylammonium bromide (CTAB on the formation of the Al(OH3 nano-structures was investigated. The experimental results indicated that the Al(OH3 microspheres composed of nanoparticles were prepared in the blank experiment, while dispersive Al(OH3 nano-particles with a diameter of 80–100 nm were produced in the presence of Al(OH3 nano-seed and CTAB.

  13. Effects of Al content on structure and mechanical properties of hot-rolled ZrTiAlV alloys

    International Nuclear Information System (INIS)

    Liang, S.X.; Yin, L.X.; Che, H.W.; Jing, R.; Zhou, Y.K.; Ma, M.Z.; Liu, R.P.

    2013-01-01

    Highlights: • Phase structure is greatly dependent on the Al content. • Intermetallic compound will precipitates while Al content is over 6.9 wt%. • Equiaxed α-phase grains present in the hot-rolled alloy with 6.9 wt% Al. • Alloys with Al content from 3.3 wt% to 5.6 wt% have good mechanical properties. - Abstract: Zirconium alloys show attractive properties for astronautic applications where the most important factors are anti-irradiation, corrosion resistance, anti-oxidant, very good strength-to-weight ratio. The effects of Al content (2.2–6.9 wt%) on structure and mechanical properties of the hot-rolled ZrTiAlV alloy samples were investigated in this study. Each sample of the hot-rolled ZrTiAlV alloys with Al contents from 2.2 wt% to 5.6 wt% is composed of the α phase and β phase, meanwhile, the relative content of the α phase increased with the Al content. However, the (ZrTi) 3 Al intermetallic compound was observed as the Al content increased to 6.9 wt%. Changes of phase compositions and structure with Al content distinctly affected mechanical properties of ZrTiAlV alloys. Yield strength of the alloy with 2.2 wt% Al is below 200 MPa. As Al content increased to 5.6 wt%, the yield strength, tensile strength and elongation of the examined alloy are 1088 MPa, 1256 MPa and 8%, respectively. As Al content further increased to 6.9 wt%, a rapid decrease in ductility was observed as soon as the (ZrTi) 3 Al intermetallic compound precipitated. Results show that the ZrTiAlV alloys with Al contents between 3.3 wt% and 5.6 wt% have excellent mechanical properties

  14. Unterstützung des wissenschaftlichen Publizierens als Aufgabe einer wissenschaftlichen Bibliothek: Die Publikationsservices an der UB Graz

    Directory of Open Access Journals (Sweden)

    Karin Lackner

    2017-12-01

    Full Text Available Die Publikationsservices, eine Servicestelle der Universität Graz, die von der Universitätsbibliothek als Stabsstelle errichtet wurde, zeigen, dass die Universitätsbibliothek im Bereich des wissenschaftlichen Publizierens eine wesentliche Rolle einnimmt. An der Universitätsbibliothek Graz wurde nicht nur innerhalb der Bibliothek Wissen zu verschiedenen Aspekten des wissenschaftlichen Publizierens zusammengeführt, vor allem wurde von der Bibliothek eine Kooperation unterschiedlicher Einrichtungen an der Universität initiiert, die in den Bereichen Forschungsunterstützung und -bewertung tätig sind, darunter Forschungsmanagement und -service sowie Leistungs- und Qualitätsmanagement. Die Bibliothek übernimmt dabei die Koordination und somit die Führungsrolle. Ziele und Aufgabenbereiche der neuen Einrichtung wurden zum einen maßgeblich durch die bereits vorhandene Expertise an der Universitätsbibliothek aus den Bereichen Universitätsverlag, Open-Access-Repositorium, Bibliometrie, Open-Access-Abkommen und Forschungsdatenmanagement und zum anderen werden sie durch die Bedürfnisse der Angehörigen der Universität, im Besonderen Lehrende und Forschende, sowie die anhaltenden Veränderungen im Bereich der wissenschaftlichen Kommunikation geprägt. Der Beitrag stellt zunächst den Themenbereich Publikationsunterstützung beziehungsweise wissenschaftliche Kommunikation als ein Aufgabengebiet für Bibliotheken vor. Dies wird dann anhand des Beispiels der Universitätsbibliothek Graz konkretisiert. Zum Abschluss wird auf weitere Entwicklungsmöglichkeiten der Publikationsservices eingegangen. A university library can assume a pivotal role in the context of scholarly publishing as can be exemplified by the publishing services at the University of Graz. This service point was established by the University Library as a functional unit within its matrix organization. The new unit has not only brought together knowledge and experience regarding

  15. Relationship between Al content and substitution mechanism of Al-bearing anhydrous bridgmanites

    Science.gov (United States)

    Noda, M.; Inoue, T.; Kakizawa, S.

    2017-12-01

    It is considered that two substitution mechanisms, Tschermak substitution and oxygen vacancy substitution, exist in MgSiO3 bridgmanite for the incorporation of Al in anhydrous condition. Kubo and Akaogi (2000) has conducted the phase equilibrium experiment in the system MgSiO3-Al2O3, and established the phase diagram up to 28 GPa. However the careful observation in the bridgmanite shows that the chemical compositions are slightly deviated from Tschermak substitution join. The same tendency can be also observed in the run products by Irifune et al. (1996). This result indicates that pure Tschermak substitution bridgmanite cannot be stable even in the MgSiO3-Al2O3 join experiment. However, the previous studies used powder samples as the starting materials, so the absorbed water may affect the results. Therefore, we tried to conduct the experiment in the join MgSiO3-Al2O3 in extremely anhydrous condition to clarify whether the pure Tschermak substitution bridgmanite can be stable or not. In addition, we also examined the stability of oxygen vacancy bridgmanite in the extremely anhydrous condition for the comparison. The high pressure synthesis experiments were conducted at 28 GPa and 1600-1700° for 1hour using a Kawai-type multi-anvil apparatus. Four different Al content samples were prepared as the starting materials along the ideal substitution line of Tschermak (Al=0.025, 0.05, 0.1, 0.15 mol) and oxygen-vacancy (Al=0.025, 0.05, 0.075, 0.1 mol) substitutions, respectively (when total cation of 2). The glass rods were used as the starting materials to eliminate the absorbed water on the sample surface. The chemical compositions of the synthesized bridgmanite could not be measured by EPMA because of small grain size less than submicron. Therefore the chemical compositions were estimated from the result of the XRD pattern by subtracting the amount of the other phases. The estimated chemical compositions of Tschermak substitution bridgmanites were consistent with the

  16. Burden of rare variants in ALS genes influences survival in familial and sporadic ALS.

    Science.gov (United States)

    Pang, Shirley Yin-Yu; Hsu, Jacob Shujui; Teo, Kay-Cheong; Li, Yan; Kung, Michelle H W; Cheah, Kathryn S E; Chan, Danny; Cheung, Kenneth M C; Li, Miaoxin; Sham, Pak-Chung; Ho, Shu-Leong

    2017-10-01

    Genetic variants are implicated in the development of amyotrophic lateral sclerosis (ALS), but it is unclear whether the burden of rare variants in ALS genes has an effect on survival. We performed whole genome sequencing on 8 familial ALS (FALS) patients with superoxide dismutase 1 (SOD1) mutation and whole exome sequencing on 46 sporadic ALS (SALS) patients living in Hong Kong and found that 67% had at least 1 rare variant in the exons of 40 ALS genes; 22% had 2 or more. Patients with 2 or more rare variants had lower probability of survival than patients with 0 or 1 variant (p = 0.001). After adjusting for other factors, each additional rare variant increased the risk of respiratory failure or death by 60% (p = 0.0098). The presence of the rare variant was associated with the risk of ALS (Odds ratio 1.91, 95% confidence interval 1.03-3.61, p = 0.03), and ALS patients had higher rare variant burden than controls (MB, p = 0.004). Our findings support an oligogenic basis with the burden of rare variants affecting the development and survival of ALS. Copyright © 2017 The Author(s). Published by Elsevier Inc. All rights reserved.

  17. Influence of Al grain boundaries segregations and La-doping on embrittlement of intermetallic NiAl

    Energy Technology Data Exchange (ETDEWEB)

    Kovalev, Anatoly I., E-mail: a_kovalev@sprg.ru; Wainstein, Dmitry L.; Rashkovskiy, Alexander Yu.

    2015-11-01

    Highlights: • We investigated Al grain boundaries segregations in ordered pure and La-doped NiAl. • Structural segregation of Al decreases critical strain for brittle cracks nucleation. • La alloying sharply improves plasticity of NiAl intermetallic. • Metallicity of interatomic bonds on grain boundaries increases at La alloying. • We have experimentally measured by EELFS that La atoms are located in Al sublattice. - Abstract: The microscopic nature of intergranular fracture of NiAl was experimentally investigated by the set of electron spectroscopy techniques. The paper demonstrates that embrittlement of NiAl intermetallic compound is caused by ordering of atomic structure that leads to formation of structural aluminum segregations at grain boundaries (GB). Such segregations contain high number of brittle covalent interatomic bonds. The alloying by La increases the ductility of material avoiding Al GB enrichment and disordering GB atomic structure. The influence of La alloying on NiAl mechanical properties was investigated. GB chemical composition, atomic and electronic structure transformations after La doping were investigated by AES, XPS and EELFS techniques. To qualify the interatomic bonds metallicity the Fermi level (E{sub F}) position and electrons density (n{sub eff}) in conduction band were determined in both undoped and doped NiAl. Basing on experimental results the physical model of GB brittleness formation was proposed.

  18. Heterogeneous nucleation of solid Al from the melt by Al 3 Ti : Molecular dynamics simulations

    KAUST Repository

    Wang, Junsheng; Horsfield, Andrew; Lee, Peter D.; Brommer, Peter

    2010-01-01

    It has been known experimentally for some time that Al3 Ti is a powerful nucleant for the solidification of aluminum from the melt; however, a full microscopic understanding is still lacking. To develop this understanding, we have performed molecular dynamics simulations of the nucleation and early stages of growth using published embedded atom method potentials for Al-Ti, but modified by us to stabilize the D 022 structure. We discover that Al3 Ti can indeed be very effective in promoting the growth of solid Al but the manner in which growth takes place depends sensitively on the surface on which the Al nucleates. In particular, complete growth of solid Al from the liquid on the (001) and (110) surfaces of Al3 Ti occurs at a lower temperature than on the (112) surface. This anisotropy agrees with observations in previous experiments. We explain this observation in terms of interfacial energies. On the preferential (111) surface of Al the solid-liquid interfacial energy is highest while the solid-vacuum energy is lowest. Our simulations also show that the extent of ordering taking place in liquid Al close to the Al 3 Ti substrate above the melting point correlates well with the effectiveness of the substrate as a nucleant below the melting temperature: this could provide a computationally efficient scheme to identify good nucleants. © 2010 The American Physical Society.

  19. Heterogeneous nucleation of solid Al from the melt by Al 3 Ti : Molecular dynamics simulations

    KAUST Repository

    Wang, Junsheng

    2010-10-27

    It has been known experimentally for some time that Al3 Ti is a powerful nucleant for the solidification of aluminum from the melt; however, a full microscopic understanding is still lacking. To develop this understanding, we have performed molecular dynamics simulations of the nucleation and early stages of growth using published embedded atom method potentials for Al-Ti, but modified by us to stabilize the D 022 structure. We discover that Al3 Ti can indeed be very effective in promoting the growth of solid Al but the manner in which growth takes place depends sensitively on the surface on which the Al nucleates. In particular, complete growth of solid Al from the liquid on the (001) and (110) surfaces of Al3 Ti occurs at a lower temperature than on the (112) surface. This anisotropy agrees with observations in previous experiments. We explain this observation in terms of interfacial energies. On the preferential (111) surface of Al the solid-liquid interfacial energy is highest while the solid-vacuum energy is lowest. Our simulations also show that the extent of ordering taking place in liquid Al close to the Al 3 Ti substrate above the melting point correlates well with the effectiveness of the substrate as a nucleant below the melting temperature: this could provide a computationally efficient scheme to identify good nucleants. © 2010 The American Physical Society.

  20. Strength of Al and Al-Mg/alumina bonds prepared using ultrahigh vacuum diffusion bonding

    International Nuclear Information System (INIS)

    King, W.E.; Campbell, G.H.; Wien, W.L.; Stoner, S.L.

    1994-01-01

    The authors have measured the cross-breaking strength of Al and Al-Mg alloys bonded with alumina. Diffusion bonding of Al and Al-Mg alloys requires significantly more bonding time than previously thought to obtain complete bonding. In contrast to previous diffusion bonding studies, fracture morphologies are similar to those obtained in bonds formed by liquid phase reaction; i.e., bonds are as strong or stronger than the ceramic; and fracture tends to propagate in the metal for pure Al and near the interface in the ceramic for the alloys. There are indications that the fracture morphology depends on Mg content and therefore on plasticity in the metal

  1. Wear protection in cutting tool applications by PACVD (Ti,Al)N and Al2O3 coatings

    International Nuclear Information System (INIS)

    Kathrein, M.; Heiss, M.; Rofner, R.; Schleinkofer, U.; Schintlmeister, W.; Schatte, J.; Mitterer, C.

    2001-01-01

    Various (Ti,Al)N-, Al 2 O 3 -, and (Ti,Al)N/Al 2 O 3 multilayer coatings were deposited onto cemented carbide cutting tool inserts by a plasma assisted chemical vapor deposition (PACVD) technique. Al 2 O 3 coatings were deposited using the gaseous mixture AlCl 3 , Ar, H 2 , and O 2 . (Ti,Al)N intermediate layers were deposited in the same device using the process mentioned and the gases AICl 3 , Ar, H 2 , TiCl 4 and N 2 . The unique properties of (Ti,Al)N/Al 2 O 3 multilayer coatings result in superior wear protection for cutting inserts applied in severe multifunction cutting processes. The influence of different deposition temperatures an structure and properties of the coatings like crystallographic phases, chemical composition, mechanical and technological properties is shown. PACVD (Ti,Al)N/Al 2 O 3 coated cutting inserts with fine grained crystalline α/κ-Al 2 O 3 offer performance advantages which are superior with respect to coatings deposited by chemical vapor deposition (CVD) due to the low deposition temperature applied. (author)

  2. Current transport mechanism in graphene/AlGaN/GaN heterostructures with various Al mole fractions

    Science.gov (United States)

    Pandit, Bhishma; Seo, Tae Hoon; Ryu, Beo Deul; Cho, Jaehee

    2016-06-01

    The current transport mechanism of graphene formed on AlxGa1-xN/GaN heterostructures with various Al mole fractions (x = 0.15, 0.20, 0.30, and 0.40) is investigated. The current-voltage measurement from graphene to AlGaN/GaN shows an excellent rectifying property. The extracted Schottky barrier height of the graphene/AlGaN/GaN contacts increases with the Al mole fraction in AlGaN. However, the current transport mechanism deviates from the Schottky-Mott theory owing to the deterioration of AlGaN crystal quality at high Al mole fractions confirmed by reverse leakage current measurement.

  3. Current transport mechanism in graphene/AlGaN/GaN heterostructures with various Al mole fractions

    Directory of Open Access Journals (Sweden)

    Bhishma Pandit

    2016-06-01

    Full Text Available The current transport mechanism of graphene formed on AlxGa1−xN/GaN heterostructures with various Al mole fractions (x = 0.15, 0.20, 0.30, and 0.40 is investigated. The current–voltage measurement from graphene to AlGaN/GaN shows an excellent rectifying property. The extracted Schottky barrier height of the graphene/AlGaN/GaN contacts increases with the Al mole fraction in AlGaN. However, the current transport mechanism deviates from the Schottky-Mott theory owing to the deterioration of AlGaN crystal quality at high Al mole fractions confirmed by reverse leakage current measurement.

  4. Assessment of phase constitution on the Al-rich region of rapidly solidified Al-Co-Fe-Cr alloys

    International Nuclear Information System (INIS)

    Wolf, W.; Bolfarini, C.; Kiminami, C.S.; Botta, W.J.

    2016-01-01

    The formation of quasicrystalline approximants in rapidly solidified Al-Co-Fe-Cr alloys was investigated. Alloys of atomic composition Al 71 Co 13 Fe 8 Cr 8 , Al 77 Co 11 Fe 6 Cr 6 and Al 76 Co 19 Fe 4 Cr 1 were produced using melt spinning and arc melting methods and their microstructural characterization was carried out by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Up to the present there is no consensus in the literature regarding the formation of quasicrystalline phase or quasicrystalline approximants in the Al 71 Co 13 Fe 8 Cr 8 alloy. This work presents, for the first time, a detailed structural characterization of selected alloys in the Al-Co-Fe-Cr system close to the atomic composition Al 71 Co 13 Fe 8 Cr 8 . The results indicated the samples to be composed, mostly, by two intermetallic phases, which are quaternary extensions of Al 5 Co 2 and Al 13 Co 4 and are quasicrystalline approximants. Although the Al 5 Co 2 phase has already been reported in the Al 71 Co 13 Fe 8 Cr 8 alloy, the presence of the monoclinic Al 13 Co 4 is now identified for the first time in the as cast state. In the binary Al-Co system a quasicrystalline phase is known to form in a rapidly solidified alloy with composition close to the monoclinic and orthorhombic Al 13 Co 4 phases. This binary quasicrystalline phase presents an average valence electron per atom (e/a) between 1.7 and 1.9; thus, in addition to the Al 71 Co 13 Fe 8 Cr 8 alloy, the compositions Al 77 Co 11 Fe 6 Cr 6 and Al 76 Co 19 Fe 4 Cr 1 were chosen to be within the region of formation of the quaternary extension of the Al 13 Co 4 phase and also within the (e/a) of 1.7 to 1.9. However, no quasicrystalline phase is present in any of the studied alloys. The Al-Co-Fe-Cr system, around the compositions studied, is composed of quaternary extensions of Al-Co intermetallic phases, which present solubility of Fe and Cr at Co atomic sites. - Highlights: •The Al rich region of the Al

  5. Comparison of ALS functionality and plant growth in ALS-inhibitor susceptible and resistant Myosoton aquaticum L.

    Science.gov (United States)

    Liu, Weitang; Bai, Shuang; Jia, Sisi; Guo, Wenlei; Zhang, Lele; Li, Wei; Wang, Jinxin

    2017-10-01

    Herbicide target-site resistance mutations may cause pleiotropic effects on plant ecology and physiology. The effect of several known (Pro197Ser, Pro197Leu Pro197Ala, and Pro197Glu) target-site resistance mutations of the ALS gene on both ALS functionality and plant vegetative growth of weed Myosoton aquaticum L. (water chickweed) have been investigated here. The enzyme kinetics of ALS from four purified water chickweed populations that each homozygous for the specific target-site resistance-endowing mutations were characterized and the effect of these mutations on plant growth was assessed via relative growth rate (RGR) analysis. Plants homozygous for Pro197Ser and Pro197Leu exhibited higher extractable ALS activity than susceptible (S) plants, while all ALS mutations with no negative change in ALS kinetics. The Pro197Leu mutation increased ALS sensitivity to isoleucine and valine, and Pro197Glu mutation slightly increased ALS sensitivity to isoleucine. RGR results indicated that none of these ALS resistance mutations impose negative pleiotropic effects on relative growth rate. However, resistant (R) seeds had a lowed germination rate than S seeds. This study provides baseline information on ALS functionality and plant growth characteristics associated with ALS inhibitor resistance-endowing mutations in water chickweed. Copyright © 2017. Published by Elsevier Inc.

  6. AL FIKR AL BALAGHI FI AL MA’ĂNI ‘INDA AS SAKĂKI FI KITABIHI MIFTAHUL ULUM DIRĂSAH BALAGHIYYAH

    Directory of Open Access Journals (Sweden)

    Talqis Nurdianto

    2018-02-01

    Full Text Available Miftāhul ‘Ulūm, written by al-Sakākī, especially the third part, was the beginning of a new phase in the development of Arabic rhetoric. Al-Sakākī divided the rhetoric into three fields of study, which are  (1 Ma’ānī, (2 Bayān, (3 Badī’. However, his style is influenced by philosophers, theologians and their verbal lexicon, which are difficult to take, especially for the ordinary recipient. Al-Sakākī described that his book containing several types of literature, namely, ‘ilm ṣarf in complete version and its conclusion, derivation science, and the grammatical study in the completeness of Ma’ānī and Bayān. The meaning of Makna is the study of completeness and conclusion. Therefore, books and prose, and poem require al-‘Arūḍ and al-Qawāfī include Ṣarf, Grammar, Ma’ānī, Bayān, limitation, reasoning, al’Arūḍ, and al-Qawāfī. He argued that the fields of study were influential in delivering knowledge to the student in order to reach the goal of the author towards his book.This research was an analytical descriptive study of al-Sakākī rhetoric that focused on the normative aspect represented by rhetorical rule and aesthetic aspects. Those aspects were shown by the feeling. Al-Sakākī rhetoric thought is a method based on mental division and has conducted in the construction of many factors, which the most important of them are philosophy and logic. Keywords: thought, rhetoric, meanings, sakkaki, study

  7. A study on wear resistance and microcrack of the Ti3Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

    International Nuclear Information System (INIS)

    Li Jianing; Chen Chuanzhong; Squartini, Tiziano; He Qingshan

    2010-01-01

    Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti 3 Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti 3 Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti 3 Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti 3 Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.

  8. Study of the 27Al(n,2,)26Al reaction via accelerator mass spectrometry

    International Nuclear Information System (INIS)

    Wallner, A.

    2000-06-01

    The excitation function for the 27 Al(n,2n) 26 Al reaction is expected to show a strongly non-linear behavior in the neutron-energy region around 14 MeV, the neutron energy in D-T plasmas; thus the production rate of 26 Al (t 1/2 =7.2*10 5 a) in D-T fusion environments can in principle be used to measure the temperature of such plasmas. Existing measurements, however, are strongly discordant. Therefore, a new accurate measurement of the 27 Al(n,2n) 26 Al cross sections in the near threshold region (E n =13.5-14.8 MeV) was performed with the goal to achieve relative cross sections with the highest accuracy possible. In addition, the measurements were also designed to provide good absolute cross-section values, as absolute cross sections are important for radioactive waste predictions. Samples of Al metal were irradiated with neutrons in the energy range near threshold (E th =13.55 MeV) at the Radiuminstitutes of both Vienna and St. Petersburg, and in Tokai-mura, Japan. In Tuebingen irradiations with neutrons of higher energies (17 and 19 MeV) were performed. The amount of 26 Al produced during the irradiations was measured via accelerator mass spectrometry (AMS) at the Vienna Environmental Research Accelerator (VERA). This work represents the first 26 Al measurements for this new facility. With this system, a background as low as 3*10 -15 for 26 Al/ 27 Al isotope ratios was obtained, corresponding to a (n,2n) cross section of 0.04 mb. Utilizing AMS, cross sections with much higher precision and considerably closer to the threshold than in previous investigations could be measured. The prerequisite for its application as a temperature monitor, namely a very well known shape of the excitation function was met. A quantitative prediction of the sensitivity of this method for monitoring the temperature in a D-T fusion plasma was therefore possible. For thermal plasmas temperature changes in the order of 5 to 15 % should be detectable. An even higher sensitivity was found

  9. Magnetostrictive properties of FeAl/polyester and FeAl/silicone composites

    Energy Technology Data Exchange (ETDEWEB)

    Riesgo, G. [Dpto. de Ciencias y Técnicas de la Navegación, Universidad de Oviedo, Campus universitario de Gijón, 33203 Gijón (Spain); Carrizo, J. [Dpto. de Física de la Universidad de Oviedo, c/ Calvo Sotelo s/n, 33007 Oviedo (Spain); Elbaile, L., E-mail: elbaile@uniovi.es [Dpto. de Física de la Universidad de Oviedo, c/ Calvo Sotelo s/n, 33007 Oviedo (Spain); Crespo, R.D. [Dpto. de Física de la Universidad de Oviedo, c/ Calvo Sotelo s/n, 33007 Oviedo (Spain); Sepúlveda, R. [Dpto. de Ingeniería Mecánica y de los Materiales, Universidad de Sevilla, Isla Cartuja, 41092 Sevilla (Spain); García, J.A. [Dpto. de Física de la Universidad de Oviedo, c/ Calvo Sotelo s/n, 33007 Oviedo (Spain)

    2017-01-15

    Highlights: • Nanocrystalline powders of FeAl have been obtained from the Fe{sub 81}Al{sub 19} ribbon produced by melt spinning. • The method allows the obtainment of a FeAl solid solution from the starting process. • The microstructure and magnetic properties of the powders were investigated. • Composites with a magnetostriction of 45 ppm have been obtained. - Abstract: Ribbons of composition Fe{sub 81}Al{sub 19} obtained by the melt spinning method have been used to yield powder by mechanical milling. Using this method, a rapid nanocrystallization and a FeAl solid solution phase was obtained from the start of the process. The microstructural and magnetic properties as well as the XRD patterns of the powders were studied in function of the milling time. Grain refinement and an increase of the coercive field were the main transformations resulting from increasing the milling time. Two sets of magnetostrictive composites were produced from the 100 h-milled powder. In one of them polyester was used as matrix and in the other one silicone. In the case of the silicone composites cured in a magnetic field of 140 mT in the longitudinal direction a saturation magnetostriction as high as 45 ppm was obtained.

  10. Thermodynamic calculation of Al-Gd and Al-Gd-Mg phase equilibria checked by key experiments

    International Nuclear Information System (INIS)

    Groebner, J.; Kevorkov, D.; Schmid-Fetzer, R.

    2001-01-01

    The binary Al-Gd and the ternary Al-Gd-Mg systems were calculated using the Calphad method. It is demonstrated that previous interpretation of ternary liquidus temperatures below 700 C must be related to other phase equilibria. The actual ternary liquidus temperatures are much higher, up to some 600 C above the previous interpretation in literature. They are widely governed by the high-melting compounds Al 2 Gd and Al 3 Gd with liquidus surfaces stretching far into the ternary system. A small number of key experiments in this work confirmed the calculated liquidus temperature and the phase relations. The available experimental data in literature fit excellently with the calculation in the binary Al-Gd system. In the ternary Al-Gd-Mg system, which is shown in several sections of the phase diagram, a good agreement can be observed too, considering the necessary reinterpretation of the liquidus temperatures suggested by Rokhlin et al. Ternary solubilities were not found experimentally. The ternary compound Al 4 GdMg (τ) forms in a ternary peritectic reaction at 761 C. (orig.)

  11. Forged HITEMAL: Al-based MMCs strengthened with nanometric thick Al{sub 2}O{sub 3} skeleton

    Energy Technology Data Exchange (ETDEWEB)

    Balog, Martin, E-mail: ummsbama@savba.sk [Institute of Materials and Machine Mechanics, Slovak Academy of Sciences, Racianska 75, 83102 Bratislava (Slovakia); Krizik, Peter; Nosko, Martin; Hajovska, Zuzana [Institute of Materials and Machine Mechanics, Slovak Academy of Sciences, Racianska 75, 83102 Bratislava (Slovakia); Victoria Castro Riglos, Maria [Centro Atómico Bariloche, Av. Bustillo 9.500, 8400 Bariloche, Río Negro (Argentina); Rajner, Walter [New Materials Development GmbH, Römerstrasse 28, 83410 Laufen, Leobendorf (Germany); Liu, De-Shin [National Chung Cheng University, 168 University Rd., Min-Hsiung, 62102 Chia-Yi, Taiwan (China); Simancik, Frantisek [Institute of Materials and Machine Mechanics, Slovak Academy of Sciences, Racianska 75, 83102 Bratislava (Slovakia)

    2014-09-08

    Bulk Al–Al{sub 2}O{sub 3} metal matrix composites (MMCs) named HITEMAL (high temperature aluminum) were fabricated in situ by forging compaction of five different types of gas-atomized commercial purity Al powders with a mean particle size in the range of 1–9 µm. As-forged HITEMAL consisted of (sub)micrometric Al grains (matrix) decorated with nanometric thick amorphous Al{sub 2}O{sub 3} (a-Al{sub 2}O{sub 3}) skeleton. Low-angle grain boundaries (LAGBs) free of Al{sub 2}O{sub 3} were located in the Al grain interior. The Al grain size and the portion of LAGBs increased with the increase in the relative powder surface area. As-forged HITEMAL shows excellent thermal stability up to 400 °C for 24 h. Annealing at temperatures ≥450 °C led to crystallization and morphological transformation from a-Al{sub 2}O{sub 3} skeleton to nanometric γ-Al{sub 2}O{sub 3} particles. Owing to the pinning effect of Al{sub 2}O{sub 3} phase, no Al grain growth took place during annealing up to 500 °C. HITEMAL showed attractive mechanical properties especially when tested at 300 °C (yield strength up to 220 MPa, Young's modulus up to 58 GPa). Despite the presence of a nearly continuous a-Al{sub 2}O{sub 3} skeleton along adjacent Al grains, forged HITEMAL materials had reasonable room temperature elongation of 7–26%. HITEMAL's elongation decreased as the Al grain size decreased and with increased testing temperature. The loss in elongation (uniform and total) was attributed to the inhomogeneous flow, which occurred due to high densities of high angle grain boundaries (dislocation sinks) and small content of LAGBs. The strength of HITEMAL stemmed from grain boundary mediated strengthening mechanisms. The results showed a positive deviation from the Hall–Petch plot, which is typical behavior of ultrafine-grained metals. Transformation of a-Al{sub 2}O{sub 3} skeleton to γ-Al{sub 2}O{sub 3} particles led to deterioration of the HITEMAL strength and Young's modulus.

  12. Determination of Al concentration in Al doped ZnO using Auger spectra excited by Mo X-rays

    International Nuclear Information System (INIS)

    Toth, J.; Koever, L.; Cserny, I.; Varga, D.

    2006-01-01

    Complete text of publication follows. A good conductor with excellent transparency is of crucial importance for the window layer of CIGS solar cells. Al doped ZnO is a good candidate for this purpose, its conductivity depends on the concentration and chemical state of the Al dopant atoms. It was demonstrated that the non-conventional XPS using Mo X-rays for excitation is a very sensitive tool for the detection of Al, P, Si [1, 2, 3]. The present paper compares the experimental ratios for Zn/Al photoinduced peak intensity ratios obtained using both Al and Mo X-ray excitations. The Mo excited Zn/Al intensity ratios can be determined with higher selectivity and sensitivity than the Zn/Al intensity ratios excited by Al X-rays. The experiments were performed with a hemispherical deflector electron spectrometer [4]. The chemical state of the Al was identified to be close to that in Al 2 O 3 . The atomic concentrations were determined using a calibration curve based on ZnO/Al samples with known composition of Al. The energy dependent efficiency of the electron spectrometer was determined comparing REELS spectra of Cu specimen to standard spectra measured by K. Goto (Nagoya Institute of Technology, Japan). For evaluation of the Al atomic concentrations from the measured photoelectron intensities the photoionisation cross-sections of Band et al [5] and the IMFP data of S. Tanuma et al [6] and C.J. Powell and A. Jablonski [7] were used. (author)

  13. Experimental evidences for reducing Mg activation energy in high Al-content AlGaN alloy by MgGa δ doping in (AlN)m/(GaN)n superlattice

    Science.gov (United States)

    Wang, Xiao; Wang, Wei; Wang, Jingli; Wu, Hao; Liu, Chang

    2017-03-01

    P-type doping in high Al-content AlGaN alloys is a main challenge for realizing AlGaN-based deep ultraviolet optoelectronics devices. According to the first-principles calculations, Mg activation energy may be reduced so that a high hole concentration can be obtained by introducing nanoscale (AlN)5/(GaN)1 superlattice (SL) in Al0.83Ga0.17N disorder alloy. In this work, experimental evidences were achieved by analyzing Mg doped high Al-content AlGaN alloys and Mg doped AlGaN SLs as well as MgGa δ doped AlGaN SLs. Mg acceptor activation energy was significantly reduced from 0.378 to 0.331 eV by using MgGa δ doping in SLs instead of traditional doping in alloys. This new process was confirmed to be able to realize high p-type doping in high Al-content AlGaN.

  14. Al-Shebab: An Al-Qaeda Affiliate Case Study (2Rev)

    Science.gov (United States)

    2017-10-01

    deputies responsible for finance , administration, and security. Coordination among regional groups is common.10 The deputy leader of al-Shebab, Mukhtar...Maaliya (Ministry of Finance ) controlled taxation. A complex court system also emerged. Multiple training camps were built that focused on hand-to-hand...Nathan Chandler, Counterterrorism and Counterinsurgency in Somalia: Assessing the Campaign Against Al Shabaab, Rand Corporation , 2016, accessed 6/5

  15. Experimental evidences for reducing Mg activation energy in high Al-content AlGaN alloy by MgGa δ doping in (AlN)m/(GaN)n superlattice

    OpenAIRE

    Xiao Wang; Wei Wang; Jingli Wang; Hao Wu; Chang Liu

    2017-01-01

    P-type doping in high Al-content AlGaN alloys is a main challenge for realizing AlGaN-based deep ultraviolet optoelectronics devices. According to the first-principles calculations, Mg activation energy may be reduced so that a high hole concentration can be obtained by introducing nanoscale (AlN)5/(GaN)1 superlattice (SL) in Al0.83Ga0.17N disorder alloy. In this work, experimental evidences were achieved by analyzing Mg doped high Al-content AlGaN alloys and Mg doped AlGaN SLs as well as MgG...

  16. Tadris Al Mufradat Li Tathbiq Maharah Al Kalam Fi Madrasah Al Muallimin Al Islamiyyah Li Mahad Bait Al Arqam Balong Jember

    Directory of Open Access Journals (Sweden)

    Muhammad Ardy Zaini

    2017-06-01

    Full Text Available There are four  skills in teaching Arabic. Ie listening, speaking, reading, and writing. Among these four, speaking considered one of the most important objectives of learning foreign language. In order to speak properly, one must know the vocabulary and apply it in a sentence. The aims of this research is to describe the teaching of vocabulary to apply the speaking skill in the school of Islamic teachers in the Institute of Bait al Arqom Balong Jember. This study used qualitative approach. The data collection was taken trough observation, personal interview, history and documentation. The teaching of vocabulary to apply the speaking skill at the Islamic Teachers' School at the Institute of Bait Al Arqam Balong Jember has gone well in terms of planning (general objectives and specific objectives, implementation (materials, use of the teaching method and teaching aids, and evaluation (assessment and evaluation. This teaching is to apply the speaking skill in terms of conversation or dialogue and lecture.

  17. NEK1 genetic variability in a Belgian cohort of ALS and ALS-FTD patients.

    Science.gov (United States)

    Nguyen, Hung Phuoc; Van Mossevelde, Sara; Dillen, Lubina; De Bleecker, Jan L; Moisse, Matthieu; Van Damme, Philip; Van Broeckhoven, Christine; van der Zee, Julie

    2018-01-01

    We evaluated the genetic impact of the amyotrophic lateral sclerosis (ALS) risk gene never in mitosis gene a-related kinase 1 (NEK1) in a Belgian cohort of 278 patients with ALS (n = 245) or ALS with frontotemporal dementia (ALS-FTD, n = 33) and 609 control individuals. We identified 2 ALS patients carrying a loss-of-function (LOF) mutation, p.Leu854Tyrfs*2 and p.Tyr871Valfs*17, that was absent in the control group. A third LOF variant p.Ser1036* was present in 2 sibs with familial ALS but also in an unrelated control person. Missense variants were common in both patients (3.6%) and controls (3.0%). The missense variant, p.Arg261His, which was previously associated with ALS risk, was detected with a minor allele frequency of 0.90% in patients compared to 0.33% in controls. Taken together, NEK1 LOF variants accounted for 1.1% of patients, although interpretation of pathogenicity and penetrance is complicated by the observation of occasional LOF variants in unaffected individuals (0.16%). Furthermore, enrichment of additional ALS gene mutations was observed in NEK1 carriers, suggestive of a "second hit" model were NEK1 variants may modify disease presentation of driving mutations. Copyright © 2017 The Author(s). Published by Elsevier Inc. All rights reserved.

  18. The effect of ammonia flow in the AlN spacer on the electrical properties of InAlN/AlN/GaN HEMT structures

    International Nuclear Information System (INIS)

    Gamarra, Piero; Lacam, Cedric; Magis, Michelle; Tordjman, Maurice; Di Forte Poisson, Marie-Antoinette

    2012-01-01

    During the past few years it has been reported that a thin AlN spacer of few nanometers needs to be inserted in InAlN/GaN high electron mobility transistors (HEMTs) to obtain high 2DEG carrier mobility. This work presents a systematic study of the effects of varying the ammonia flow in the AlN spacer of InAlN/AlN/GaN HEMTs grown by low pressure metalorganic vapour phase epitaxy (LP-MOVPE). The strain state, the surface roughness and the growth rate of AlN were found to be dependent on the V/III ratio. In addition the ammonia flow in the interlayer has a strong impact on the structural properties of the subsequent InAlN barrier layer and on the electrical properties of the structure. A sheet resistance as low as 327 Ω/□ with a sheet carrier density of 1.5 x 10 13 cm -2 has been obtained at room temperature. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  19. The effect of ammonia flow in the AlN spacer on the electrical properties of InAlN/AlN/GaN HEMT structures

    Energy Technology Data Exchange (ETDEWEB)

    Gamarra, Piero; Lacam, Cedric; Magis, Michelle; Tordjman, Maurice; Di Forte Poisson, Marie-Antoinette [III-V Lab., Marcussis (France)

    2012-01-15

    During the past few years it has been reported that a thin AlN spacer of few nanometers needs to be inserted in InAlN/GaN high electron mobility transistors (HEMTs) to obtain high 2DEG carrier mobility. This work presents a systematic study of the effects of varying the ammonia flow in the AlN spacer of InAlN/AlN/GaN HEMTs grown by low pressure metalorganic vapour phase epitaxy (LP-MOVPE). The strain state, the surface roughness and the growth rate of AlN were found to be dependent on the V/III ratio. In addition the ammonia flow in the interlayer has a strong impact on the structural properties of the subsequent InAlN barrier layer and on the electrical properties of the structure.istance as low as 327 {omega}/{open_square} with a sheet carrier density of 1.5 x 10{sup 13} cm{sup -2} has been obtained at room temperature. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. Assessment of phase constitution on the Al-rich region of rapidly solidified Al-Co-Fe-Cr alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, W., E-mail: witorw@gmail.com [Programa de Pós-Graduação em Ciência e Engenharia de Materiais, Universidade Federal de São Carlos, Rod. Washington Luiz, Km 235, 13565-905 São Carlos, SP (Brazil); Bolfarini, C., E-mail: cbolfa@ufscar.br [Departamento de Engenharia de Materiais, Universidade Federal de São Carlos, Rod. Washington Luiz, Km 235, 13565-905 São Carlos, SP (Brazil); Kiminami, C.S., E-mail: kiminami@ufscar.br [Departamento de Engenharia de Materiais, Universidade Federal de São Carlos, Rod. Washington Luiz, Km 235, 13565-905 São Carlos, SP (Brazil); Botta, W.J., E-mail: wjbotta@ufscar.br [Departamento de Engenharia de Materiais, Universidade Federal de São Carlos, Rod. Washington Luiz, Km 235, 13565-905 São Carlos, SP (Brazil)

    2016-12-15

    The formation of quasicrystalline approximants in rapidly solidified Al-Co-Fe-Cr alloys was investigated. Alloys of atomic composition Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8}, Al{sub 77}Co{sub 11}Fe{sub 6}Cr{sub 6} and Al{sub 76}Co{sub 19}Fe{sub 4}Cr{sub 1} were produced using melt spinning and arc melting methods and their microstructural characterization was carried out by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Up to the present there is no consensus in the literature regarding the formation of quasicrystalline phase or quasicrystalline approximants in the Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8} alloy. This work presents, for the first time, a detailed structural characterization of selected alloys in the Al-Co-Fe-Cr system close to the atomic composition Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8}. The results indicated the samples to be composed, mostly, by two intermetallic phases, which are quaternary extensions of Al{sub 5}Co{sub 2} and Al{sub 13}Co{sub 4} and are quasicrystalline approximants. Although the Al{sub 5}Co{sub 2} phase has already been reported in the Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8} alloy, the presence of the monoclinic Al{sub 13}Co{sub 4} is now identified for the first time in the as cast state. In the binary Al-Co system a quasicrystalline phase is known to form in a rapidly solidified alloy with composition close to the monoclinic and orthorhombic Al{sub 13}Co{sub 4} phases. This binary quasicrystalline phase presents an average valence electron per atom (e/a) between 1.7 and 1.9; thus, in addition to the Al{sub 71}Co{sub 13}Fe{sub 8}Cr{sub 8} alloy, the compositions Al{sub 77}Co{sub 11}Fe{sub 6}Cr{sub 6} and Al{sub 76}Co{sub 19}Fe{sub 4}Cr{sub 1} were chosen to be within the region of formation of the quaternary extension of the Al{sub 13}Co{sub 4} phase and also within the (e/a) of 1.7 to 1.9. However, no quasicrystalline phase is present in any of the studied alloys. The Al-Co-Fe-Cr system

  1. Corrosion analysis of AlMg2 and AlMgSi using electrochemical method

    International Nuclear Information System (INIS)

    Dian A; Maman Kartaman; Rosika K; Yanlinastuti

    2014-01-01

    Corrosion test of cladding materials and structures of research reactor fuel, AlMgSi and AlMg2 have been performed in demineralized water of pH 2 and 6.7 using an electrochemical method. Corrosion phenomenon is affected by several factor such as composition and condition of solution. The purpose of this activity is to investigate the corrosion phenomena through the determination of the parameters of corrosion and polarization curve. The materials used are AlMg2 and AlMgSi alloy in circular dish shape with an area of 1 Cm"2. Preparation of the test sample is performed through several stages polishing, cleaning and drying procedures followed ASTM G3. The electrochemical method is done by measuring the open circuit potential (OCP), polarization resistance and potentiodynamic in demineralized water of pH 2 and pH 6.7 at temperature of 25°C. The results of the OCP is the corrosion potential (Ecorr) of AlMg2 and AlMgSi each of -906.1 mV and -619.8 mV at pH 2 and -868.6 and -756.7 mV at pH 6.7 mV. The results of measurements by polarization resistance technique showed that the corrosion rate of AlMg2 and AlMgSi in safe category (<2 mpy) at pH 6.7 and at pH 2 corrosion rate increased significantly, but still in the lightweight category (<20 mpy). Potentiodynamic curves showed that the passivation at pH 6.7 is very low while the passivation at pH 2 occurs within a relatively short range potential and followed events corroded. (author)

  2. Catalytic effect of Al and AlN interlayer on the growth and properties of containing carbon films

    International Nuclear Information System (INIS)

    Zhou, Bing; Liu, Zhubo; Tang, Bin; Rogachev, A.V.

    2015-01-01

    Highlights: • DLC and CN x bilayers with Al (AlN) interlayer were fabricated by cathode arc technique. • Complete diffusion of Al and C atoms occurs at the interface of Al/DLC (CN x ) bilayer. • Al/CN x bilayer presents a higher content of Csp 3 /Csp 2 bonds. • The hardness of Al/DLC bilayer decreases but increases for the other bilayers. • Morphology of the bilayers was explained by growth mechanism of DLC and surface state of substrate. - Abstract: Diamond-like carbon (DLC) and carbon nitride (CN x ) bilayer films with Al and AlN interlayer were fabricated by pulse cathode arc technique. The structure, composition, morphology and mechanical properties of the films were investigated by Raman, Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), Knoop sclerometer and surface profilometer. The results indicated that the complete diffusion between C and Al atoms occurs in the Al/DLC and Al/CN x bilayer. Al interlayer induces the increase of the size and ordering of Csp 2 clusters in the films but AlN interlayer increases the disordering degree of Csp 2 clusters. XPS results showed that a higher content of Csp 3 /Csp 2 bonds presents in the Al/CN x bilayer, and Al and AlN interlayer decreases the atomic ratio of N/C. AFM with phase contrast mode illustrated the morphologic characteristics of the bilayer films. All the bilayers show a nano-structural surface. The morphology changes of the bilayer were well explained by the surface state of the substrate and the growth mechanism of DLC films. The hardness of Al/DLC bilayer decreases but it increases for the other bilayers compared to the corresponding DLC (CN x ) monolayer. The internal stress of the bilayer is significantly lower than that of the monolayer except for the AlN/CN x bilayer. These studies could make the difference at the time of choosing a suitable functional film for certain application

  3. Characteristics in AlN/AlGaN/GaN Multilayer-Structured High-Electron-Mobility Transistors

    International Nuclear Information System (INIS)

    Gui-Zhou, Hu; Ling, Yang; Li-Yuan, Yang; Si, Quan; Shou-Gao, Jiang; Ji-Gang, Ma; Xiao-Hua, Ma; Yue, Hao

    2010-01-01

    A new multilayer-structured AlN/AlGaN/GaN heterostructure high-electron-mobility transistor (HEMT) is demonstrated. The AlN/AlGaN/GaN HEMT exhibits the maximum drain current density of 800 mA/mm and the maximum extrinsic transconductance of 170 mS/mm. Due to the increase of the distance between the gate and the two-dimensional electron-gas channel, the threshold voltage shifts slightly to the negative. The reduced drain current collapse and higher breakdown voltage are observed on this AlN/AlGaN/GaN HEMT. The current gain cut-off frequency and the maximum frequency of oscillation are 18.5 GHz and 29.0 GHz, respectively. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  4. 60Co gamma radiation effect on AlGaN//AlN/GaN HEMT devices

    International Nuclear Information System (INIS)

    Wang Yanping; Luo Yinhong; Wang Wei; Zhang Keying; Guo Hongxia; Guo Xiaoqiang; Wang Yuanming

    2013-01-01

    The testing techniques and experimental methods of the 60 Co gamma irradiation effect on AlGaN/AlN/GaN high electron mobility transistors (HEMTs) are established. The degradation of the electrical properties of the device under the actual radiation environment are analyzed theoretically, and studies of the total dose effects of gamma radiation on AlGaN/AlN/GaN HEMTs at three different radiation bias conditions are carried out. The degradation patterns of the main parameters of the AlGaN/AlN/GaN HEMTs at different doses are then investigated, and the device parameters that were sensitive to the gamma radiation induced damage and the total dose level induced device damage are obtained. (authors)

  5. Cu-segregation at the Q'/α-Al interface in Al-Mg-Si-Cu alloy

    International Nuclear Information System (INIS)

    Matsuda, Kenji; Teguri, Daisuke; Uetani, Yasuhiro; Sato, Tatsuo; Ikeno, Susumu

    2002-01-01

    Cu segregation was detected at the Q ' /α-Al interface in an Al-Mg-Si-Cu alloy by energy-filtered transmission electron microscopy. By contrast, in a Cu-free Al-Mg-Si alloy no segregation was observed at the interface between the matrix and Type-C precipitate

  6. Effect of Al-5Ti-0.62C-0.2Ce Master Alloy on the Microstructure and Tensile Properties of Commercial Pure Al and Hypoeutectic Al-8Si Alloy

    Directory of Open Access Journals (Sweden)

    Wanwu Ding

    2017-06-01

    Full Text Available Al-5Ti-0.62C-0.2Ce master alloy was synthesized by a method of thermal explosion reaction in pure molten aluminum and used to modify commercial pure Al and hypoeutectic Al-8Si alloy. The microstructure and tensile properties of commercial pure Al and hypoeutectic Al-8Si alloy with different additions of Al-5Ti-0.62C-0.2Ce master alloy were investigated. The results show that the Al-5Ti-0.62C-0.2Ce alloy was composed of α-Al, granular TiC, lump-like TiAl3 and block-like Ti2Al20Ce. Al-5Ti-0.62C-0.2Ce master alloy (0.3 wt %, 5 min can significantly refine macro grains of commercial pure Al into tiny equiaxed grains. The Al-5Ti-0.62C-0.2Ce master alloy (0.3 wt %, 30 min still has a good refinement effect. The tensile strength and elongation of commercial pure Al modified by the Al-5Ti-0.62C-0.2Ce master alloy (0.3 wt %, 5 min increased by roughly 19.26% and 61.83%, respectively. Al-5Ti-0.62C-0.2Ce master alloy (1.5 wt %, 10 min can significantly refine both α-Al grains and eutectic Si of hypoeutectic Al-8Si alloy. The dendritic α-Al grains were significantly refined to tiny equiaxed grains. The morphology of the eutectic Si crystals was significantly refined from coarse needle-shape or lath-shape to short rod-like or grain-like eutectic Si. The tensile strength and elongation of hypoeutectic Al-8Si alloy modified by the Al-5Ti-0.62C-0.2Ce master alloy (1.5 wt %, 10 min increased by roughly 20.53% and 50%, respectively. The change in mechanical properties corresponds to evolution of the microstructure.

  7. Tailoring ultrafine grained and dispersion-strengthened Ti2AlC/TiAl ...

    Indian Academy of Sciences (India)

    and Ti-Al pre-alloyed powders at low temperature of 1150◦C. The composite mainly consisted ... Metal–matrix composites; mechanical properties; microstructures; sintering. 1. Introduction γ-TiAl-based intermetallic alloys have been extensively.

  8. Stagnation of the exploitation of Al ores and the depression of world prices of Al

    Directory of Open Access Journals (Sweden)

    Slavkovský Jozef

    1999-03-01

    Full Text Available In the contribution, data on Al – a metal of the 20th century are compiled together with the problems of genesis of the Al mineral raw ma-terials as well as types of bauxite and Al-laterite deposits. Furthermore, an overview of the world exploitation of bauxite during 1935-1980 is given along with the prognoses to 2000 and present situation (1992-1996. Overviews of the production of Al follows, providing its rela-tion to the bauxite exploitation. Contrary to the prognoses, a stabilization or stagnation has been observed in the exploitation of bauxite and production of Al during nineties, which a tendency is directly reflected in the world price of this commodity. When analyzing the Al prices for a longer period, some serious deviations can be noticed, that however presently represent a long-term minimum. We hope the stagnation of the production and the price decline are only temporary and new possibilities of the utilization of Al will be found soon.

  9. A study on preparation and hydriding of β-Mg2Al3 and γ-Mg17Al12

    International Nuclear Information System (INIS)

    Hadi Suwarno

    2009-01-01

    The mechanism of the synthetic formation of β-Mg 2 Al 3 and γ-Mg 17 Al 12 has been studied. Mechanical alloying of Mg and Al powders with the atomic ratio of Mg:Al = 2:3 in toluene solution yields β-Mg 2 Al 3 compound after milling for 30 h. The γ-Mg 17 Al 12 can be formed by heating the β-Mg 2 Al 3 at 430°C under high vacuum. The measured hydrogen capacities of β-Mg 2 Al 3 and γ-Mg 17 Al 12 as hydride at 300°C are 3.2 and 4.9 wt%, respectively. Microstructure of the Mg-Al specimen shows that on hydriding at 300°C the polygonal shape of the γ-Mg 17 Al 12 changes into irregular shapes which are composed of γ-MgH 2 and Al. (author)

  10. Marinbiologisk optegnelse i NUḪBAT AL-DAHR FĪ ʿAǦ ʾIB AL-BARR WA-AL-BAḤR

    OpenAIRE

    Provencal, Philippe

    2014-01-01

    I det arabiske geografiske værk NUḪBAT AL-DAHR FĪ ʿAǦ ʾIB AL-BARR WA-AL-BAḤR (færdigskrevet mellem 1324 og 1327) fra omtales seks dyr fra Adenbugten. Det dreje sig om savrokke, kuglefisk, pilrokke, pindsvinefisk og hvalhaj. Det sidste dyr har ikke kunnet bestemmes. Artiklen bringer en oversættelse af optegnelsen til engelsk samt både en filologisk som en biologisk kommentar. The aim of this article is to present a medieval Arabic report regarding sixanimals from the Gulf of Aden, to provid...

  11. MOSQUE ARCHITECTURE AS A SUSTAINABLE BUILDING IN URBAN (Case Study: Al Markas Al Islamic Mosque Makassar

    Directory of Open Access Journals (Sweden)

    Imriyanti Imriyanti

    2014-02-01

    Full Text Available Abstract Mosque Architecture is a part of Islamic architecture. Mosque should be fused with elements of nature because its function as a place to pray to God who created the universe. Al Markas Al Islamic Makassar mosque is used as a center of Islamic aspirations of the people and the government to accommodate all the activities of moslems in Makassar. Through this function, the provision of Al Markas Al Islamic mosque began from the desire of Islamic societies in Makassar, which wants the Islamic center to be equipped with facilities and infrastructure as well as architectural, monumental buildings and structures that can be last for hundreds of years (continuous, blend with the environment, and also can be used by the public. Having regard to the function of a mosque especially at the Al Markas Al Islamic Makassar mosque, then the problem that arise is how the Al Markas Al Islamic mosque can be survived/sustainable  in order  to function  as a place  of worship  and  as a center  of Islam.  This research  is a descriptive qualitative research that is trying to generate data in the form of systematic and accurate picture of the object of study. The sustaiprophetlity  of Al Markas AL Islamic mosque can be known through the concept of Islam  in accordance with the view of Islam as well as the sustaiprophetlity of the buildings that seen in the spatial pattern of the mosque, appearance, natural lighting, natural ventilation, and user behavior of the mosque. Keywords: mosque architecture, sustaiprophetlity, view of Islam     Abstrak Arsitektur masjid merupakan bagian dari arsitektur Islam. Bangunan masjid sebaiknya dapat menyatu dengan unsur alam karena masjid difungsikan sebagai wadah dalam bersujud/sembahyang  kepada Allah SWT yang menciptakan alam semesta ini. Masjid Al Markas Al Islamic Makassar merupakan kompleks kegiatan Islam yang digunakan sebagai pusat aspirasi masyarakat  dan pemerintahan  yang dapat menampung

  12. Adhesive and tribocorrosive behavior of TiAlPtN/TiAlN/TiAl multilayers sputtered coatings over CoCrMo

    Science.gov (United States)

    Canto, C. E.; Andrade, E.; Rocha, M. F.; Alemón, B.; Flores, M.

    2017-09-01

    The tribocorrosion resistance and adherence of multilayer coatings of TiAlPtN/TiAlN/TiAl synthesized by PVD reactive magnetron sputtering over a CoCrMo alloy substrate in 10 periods of 30 min each were analyzed and compared to those of the substrate alone and to that of a TiAlPtN single layer coating of the same thickness. The objective of the present work was to create multilayers with different amounts of Pt in order to enhance the tribocorrosion resistance of a biomedical alloy of CoCrMo. Tribocorrosion tests were performed using Simulated Body Fluid (SBF) at typical body temperature with a tribometer in a pin on disk test. The elemental composition and thickness of the coating which behave better at the tribocorrosion tests were evaluated by means of RBS (Rutherford Backscattering Spectroscopy) IBA (Ion Beam Analysis) technique, using an alpha particles beam of 1.8 MeV, before and after the reciprocating motion in the tribocorrosion test. In order to simulate the elemental profile of the samples, the SIMNRA simulation computer code was used. Measurements of the adhesion of the coatings to the substrate were carried on by means of a scratch test using a tribometer. By taking micrographs of the produced tracks, the critical loads at which the coatings are fully separated from the substrate were determined. From these tests it was observed that a coating with 10 min of TiAlPtN in a TiAlPtN/TiAl period of 30 min in multilayers of 10 periods and with an average thickness of 145 nm for the TiAlPtN nanolayers had the best tribocorrosion resistance behavior, compared to that of the CoCrMo alloy. The RBS experiments showed a reduction of the thickness of the films along with some loss of the multilayer structure after the reciprocating motion. The adhesion tests indicated that the multilayer with the average TiAlPtN thickness of 145 nm displayed the highest critical load. These results indicate a high correlation between the adherence and the tribocorrosion behavior.

  13. Microstructure of Reaction Zone Formed During Diffusion Bonding of TiAl with Ni/Al Multilayer

    Science.gov (United States)

    Simões, Sónia; Viana, Filomena; Koçak, Mustafa; Ramos, A. Sofia; Vieira, M. Teresa; Vieira, Manuel F.

    2012-05-01

    In this article, the characterization of the interfacial structure of diffusion bonding a TiAl alloy is presented. The joining surfaces were modified by Ni/Al reactive multilayer deposition as an alternative approach to conventional diffusion bonding. TiAl substrates were coated with alternated Ni and Al nanolayers. The nanolayers were deposited by dc magnetron sputtering with 14 nm of period (bilayer thickness). Joining experiments were performed at 900 °C for 30 and 60 min with a pressure of 5 MPa. Cross sections of the joints were prepared for characterization of their interfaces by scanning electron microscopy (SEM), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM), high resolution TEM (HRTEM), energy dispersive x-ray spectroscopy (EDS), and electron backscatter diffraction (EBSD). Several intermetallic compounds form at the interface, assuring the bonding of the TiAl. The interface can be divided into three distinct zones: zone 1 exhibits elongated nanograins, very small equiaxed grains are observed in zone 2, while zone 3 has larger equiaxed grains. EBSD analysis reveals that zone 1 corresponds to the intermetallic Al2NiTi and AlNiTi, and zones 2 and 3 to NiAl.

  14. Al-quran dalam Perspektif Budaya

    OpenAIRE

    Sudrajat, Ajat

    2009-01-01

    Al-Quran merupakan kitab suci terakhir yang diturunkan kepada manusia. Tujuan utama diturunkannya al-Quran adalah sebagai kitab petunjuk yang meliputi bidang akidah, syariah, dan akhlak. Akan tetapi di luar ketiga petunjuk tersebut, al-Quran telah memberikan motivasi dan inspirasi kepada umat Islam dalam berbagai bidang kehidupan sehingga melahirkan jenis budaya tertentu. Dialog intelektual yang dilakukan secara kreatif oleh umat Islam terhadap al-Quran ternyata telah menghasilkan lahirnya ge...

  15. ITIJAHAT KAUN AL-NABI WA AL-RASUL FI SYAKHSIYAH MUHAMMAD FI NATSR MAULID AL-BARZANJI

    Directory of Open Access Journals (Sweden)

    Himmah Istomah

    2017-08-01

    Full Text Available One of human personalities is humanist. Based on the understanding of Maslow’s theory of motivation, researcher seeks to uncover kinds of motivational needs of Muhammad Saw contained in Maulid Al-Barzanjiy (the work of Ja 'far bin Hasan al-Barzanji (d. 1763 M. The goal is realized through a descriptive qualitative approach with  text analysis  about Psycholiterature of Endraswara. The results of this study indicate that in Maulid Al-Barzanji there are Muhammad Saw’s five needs and how their satisfying perfectly,  namely: physiological needs, safety, social, esteem, and self-actualization. Thus, it can be interpreted that Muhammad SAW as an ordinary human having motivational needs. His prophetic and apostleship honor is not a direct blessing from Allah, but he had been through some complicated processes in life. This can be applied by his followers, so they can complete their motivational needs to reach the satiation as a caliph and to be useful person in this world.

  16. Microstructure and bonding mechanism of Al/Ti bonded joint using Al-10Si-1Mg filler metal

    International Nuclear Information System (INIS)

    Sohn, Woong H.; Bong, Ha H.; Hong, Soon H.

    2003-01-01

    The microstructures and liquid state diffusion bonding mechanism of cp-Ti to 1050 Al using an Al-10.0wt.%Si-1.0wt.%Mg filler metal with 100 μm in thickness have been investigated at 620 deg. C under 1x10 -4 Torr. The effects of bonding process parameters on microstructure of bonded joint have been analyzed by using an optical microscope, AES, scanning electron microscopy and EDS. The interfacial bond strength of Al/Ti bonded joints was measured by the single lap shear test. The results show that the bonding at the interface between Al and filler metal proceeds by wetting the Al with molten filler metal, and followed by removal of oxide layer on surface of Al. The interface between Al and filler metal moved during the isothermal solidification of filler metal by the diffusion of Si from filler metal into Al layer. The interface between Al and filler metal became curved in shape with increasing bonding time due to capillary force at grain boundaries. The bonding at the interface between Ti and filler metal proceeds by the formation of two different intermetallic compound layers, identified as Al 5 Si 12 Ti 7 and Al 12 Si 3 Ti 5 , followed by the growth of the intermetallic compound layers. The interfacial bond strength at Al/Ti joint increased with increasing bonding time up to 25 min at 620 deg. C. However, the interfacial bond strength of Al/Ti joint decreased after bonding time of 25 min at 620 deg. C due to formation of cavities in Al near Al/intermetallic interfaces

  17. Micromechanisms of fracture and fatigue in Ti3Al based and TiAl based intermetallics

    International Nuclear Information System (INIS)

    James, A.W.; Chave, R.A.; Hippsley, C.A.; Bowen, P.

    1993-01-01

    Micromechanisms of fracture and fatigue crack growth resistance in specific Ti 3 Al based and TiAl based intermetallics are reviewed. Effects of test temperature, environment and microstructure on crack growth resistance are considered in detail for several Ti 3 Al and Ti'Al based intermetallic systems under development. The implications of these studies for the structural reliability of these materials is also addressed briefly. (orig.)

  18. Core electron binding energy shifts of AlBr3 and Al2Br6 vapor

    International Nuclear Information System (INIS)

    Mueller, Astrid M.; Plenge, Juergen; Leone, Stephen R.; Canton, Sophie E.; Rude, Bruce S.; Bozek, John D.

    2006-01-01

    The Al 2p and Br 3d inner-shell photoelectron spectra of aluminum tribromide monomer and dimer vapor were measured at 90 and 95 eV photon energy, respectively, to determine the core electron binding energies of the atoms in the two molecular species. While AlBr 3 has three identical Br atoms, Al 2 Br 6 exhibits four terminal and two bridging Br atoms. The species are identified by their distinct valence photoelectron spectra. Comparison of the observed Al 2p 1/2 and Al 2p 3/2 electron binding energies of AlBr 3 with those of Al 2 Br 6 shows that there is a chemical shift of (0.15 ± 0.03) eV to lower energy in the dimer. In Al 2 Br 6 , an assignment is proposed in which the Br 3d 3/2 and Br 3d 5/2 binding energies of terminal Br atoms are (1.18 ± 0.03) eV lower than those of bridging Br atoms. This assignment assumes that both types of Br atoms have similar cross-sections for ionization. With this result, the Br 3d 3/2 and Br 3d 5/2 binding energies of Br atoms in AlBr 3 are (0.81 ± 0.03) eV lower than those of bridging Br atoms of the dimer but (0.37 ± 0.03) eV higher than those of terminal Br atoms of the dimer. The obtained chemical shifts are considered in terms of the binding relations and electron density distributions in both molecules. Chemical shifts that are larger than a few hundred millielectron volts, as observed in the Al 2 Br 6 /AlBr 3 system, offer potential to study the dissociation dynamics of the dimer in a femtosecond visible or ultraviolet-pump/XUV-probe experiment

  19. PENDEKATAN HERMENEUTIK DALAM PEMAHAMAN HADIS (Kajian Kitab Fath al-Bari Karya Ibn Hajar Al-‘Asqalani

    Directory of Open Access Journals (Sweden)

    Agusni Yahya

    2014-12-01

    Full Text Available The hadith explanation book of Sahih al-Bukhari written by Ibn Hajar Al-‘Asqalani, Fath al-Bari, is one of the most pupular books in Moslem ummah. Is widely used by Moslem scholars to meet the meanings of hadiths compiled by the imam al-Bukhari in his Sahih al-Bukhari. Fath al-Bari is considered significant to do the research on it in order to develop the science of hadith, mainly through the hermeneutic method. By using this method, the research questions are: 1. How does Ibn Hajar Al-‘Asqalani explain the matans (hadith texts of Sahih al Bukhari in connection with hermeneutic method? 2. What are the hermeneutic principles used by Ibn Hajar Al-‘Asqalani in his explanations of hadith? This research is expected to respond the research questions above so that it can be implimented the field of hadith in relation to develop hadith methodology. Finally, the research uncover that in his explanations of hadiths,  Ibn Hajar Al-‘Asqalani is oriented his world views to the classical Islam, the era of Prophet’s companions and their successors, the Salaf al-Salih. He does not express the Islamic world issues available in his time in his explanations of the hadiths. He is considered a normative ‘ulama since he is not influenced by the emerging cases situated his time in Egypt, Mecca and Madina. He tends to be textual to explain the matans of hadiths although to some extent he uncovers the historical contexts of the hadiths he explains. This is common for a muhadith  whose main jobs is to collect and narrate the whole data on Prophet's sayings, acts and permissions either on sanads (narrators or matans (texts.Keywords:  Fath al-Bari; sharh al-hadith; hermeneutik.

  20. Consequences of the amended Biomass Waste Ordinance for biological waste treatment; Konsequenzen der novellierten Bioabfallverordnung fuer die biologische Abfallbehandlung

    Energy Technology Data Exchange (ETDEWEB)

    Kehres, Bertram [Bundesguetegemeinschaft Kompost e.V. (BGK), Koeln (Germany)

    2012-11-01

    The amended Biomass Waste Ordinance will bring about changes in biological waste treatment to which operators of composting and fermenting plants will have to adapt. The contribution outlines the most relevant changes; at the time of publication, it was not known how the Bundesrat would decide with regard to the Amendment, probably in late March 2012. (orig.) [German] Die Novelle der Bioabfallverordnung wird fuer die biologische Abfallbehandlung verschiedene Veraenderungen mit sich bringen, auf die sich Betreiber von Kompostierungs- und von Vergaerungsanlagen einzustellen haben. Auf die wesentlichen Aenderungen wird in diesem Beitrag eingegangen. Zum Zeitpunkt der Abfassung dieses Beitrages ist allerdings noch nicht vollstaendig bekannt, wie der Bundesrat - voraussichtlich Ende Maerz 2012 - ueber die Novelle abschliessend entscheiden wird. (orig.)

  1. Digitalisierung und Selbstbestimmung

    Directory of Open Access Journals (Sweden)

    Eisenberger, Iris

    2017-12-01

    Full Text Available Kurztext: Der Beitrag beleuchtet das Verhältnis von Digitalisierung und Recht. Am Beispiel der Blockchain-Technologie wird aufgezeigt, wie neue Formen und Räume der Selbstbestimmung geschaffen werden können. In distribuierten Systemen ist die Tendenz erkennbar, dass sich die rechtliche hin zu einer technologischen Steuerung verlagert. Wenn Funktionen, die für gewöhnlich der demokratisch legitimierte Gesetzgeber wahrnimmt, auf andere Systeme übergehen, führt dies zu Herausforderungen für rechtsstaatliche Demokratien. Fundamentale Fragen von Kontrolle und Machtbeschränkung iZm Digitalisierung stehen im Fokus. Der Beitrag plädiert schließlich für „legal foresight“-Forschung im Bereich neuer Technologien.

  2. Thermophysical properties of αAl2O3, MgAl2O4 and AlN at low tempertures

    International Nuclear Information System (INIS)

    Burghartz, S.

    1995-12-01

    A possibility for producing energy in future might be the nuclear fusion. The process of nuclear fusion is characterized by melting nuclei of hydrogen atoms (deuterium and tritium) which yield to the production of helium atom nuclei. For this process extremely high temperatures of the deuterium-tritium-gas plasma are necessary. The additional heating of the plasma by microwaves requires materials with low diaelectric losses and high thermal conductivity. The thermal conductivity can be increased by cooling the windows which lead to the plasma chambre. Experimental investigations with the aim to check the influence of liquid nitrogen (T=70 K) on the cooling of the windows were performed in the temperature region 70 K 2 O 3 , MgAl 2 O 4 and AlN were measured. The thermal conductivity can be calculated using the equation λ=αc p ρ λ=thermal conductivity α=thermal diffusivity c p =specific heat (at constant pressure) ρ=density. Furthermore a theoretical method to calculate the thermal conductivity at low temperatures is presented; this is done by using a model modification of heat transport in electric insulators. As result the influence of intrinsic parameters (crystal structure, interatomar binding, anharmonicity) and extrinsic parameters (point defects, dislocations, boundary areas) upon thermal conductivity of α-Al 2 O 3 , MgAl 2 O 4 and AlN are achieved. (orig.)

  3. Grain refinement of Al wrought alloys with newly developed AlTiC master alloys; Kornfeinung von Al-Knetlegierungen mit neu entwickelten AlTiC-Vorlegierungen

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, W. [Vereinigte Aluminium-Werke AG, Bonn (Germany). Forschung und Entwicklung

    2000-10-01

    AlTiC master alloys are a new grain refiner type to produce an equiaxed grain structure of cast extrusion and rolling ingots. These master alloys contain Ti carbides which act as nucleants of the {alpha} solid solution during solidification. The TiC content is lower than the TiB{sub 2} content of the industrial proved AlTiB master alloys. Benefits of the AlTiC master alloys are the low agglomeration tendency of the Ti carbides in the melt and that no Zr poisoning takes place. Despite of the low Ti carbide content the grain refinement performance can be very efficient, if low melt temperatures during casting will be used and as result of this a sufficient constitutional supercooling at the solidification front is achieved. (orig.)

  4. Advanced life support (ALS) instructors experience of ALS education in Western Australia: a qualitative exploratory research study.

    Science.gov (United States)

    Taplin, John; McConigley, Ruth

    2015-04-01

    When cardiac arrest occurs, timely competent advanced life support (ALS) interventions by nursing staff can influence patient outcomes. Ongoing ALS education influences maintenance of competency and avoids skill decay. To explore the methods of ALS education delivery for nurses in the workplace; describe the issues relating to maintaining ALS competency; explore ALS competency decay for nurses and develop recommendations for the provision of continuing ALS education. A qualitative exploratory design was used to study ALS education provision in the workplace. Data were collected from ALS nurse experts in Western Australia by face-to-face and phone interviews. Semi-structured interviews were conducted and organised around a set of predetermined questions. Two major themes were identified; the first theme Demand and Supply describes the increasing demand for ALS education for nurses and the challenges with providing timely cost effective traditional face-to-face ALS education. The second theme, Choosing The Best Education Options describes new ways to provide ALS education using emerging technologies. The study suggested that using e-learning methods would assist with educating the maximum amount of nurses in a timely manner and e-learning and teleconferencing offer opportunities to reach nurses in distant locations. Delivering ALS education more frequently than annually would increase skills maintenance and lessen skill decay. Further research is required to explore which blended e-learning model is best suited to ALS education. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Al-Qaeda-Syria (AQS): An Al-Qaeda Affiliate Case Study

    Science.gov (United States)

    2017-10-01

    Special Operations/Low Intensity Conflict CT Counterterrorism FF Foreign Fighter FSA Free Syrian Army GEC Global Engagement Center HTS Hay’at...war as an opportunity for the global jihadist movement, an opportunity that paralleled the one Iraq had offered a decade earlier.11 He was initially...Zawahiri’s vision of Al-Qaeda franchises oriented toward winning popular support. When al-Zawahiri published his “General Guidelines for Jihad” in

  6. Mechanochemical synthesis of Cu-Al and methyl orange intercalated Cu-Al layered double hydroxides

    International Nuclear Information System (INIS)

    Qu, Jun; He, Xiaoman; Chen, Min; Hu, Huimin; Zhang, Qiwu; Liu, Xinzhong

    2017-01-01

    In this study, a mechanochemical route to synthesize a Cu-Al layered double hydroxide (LDH) and a methyl orange (MO) intercalated one (MO-LDH) was introduced, in which basic cupric carbonate (Cu_2(OH)_2CO_3) and aluminum hydroxide (Al(OH)_3) with Cu/Al molar ratio at 2/1 was first dry ground for 2 h and then agitated in water or methyl orange solution for another 4 h to obtain the LDH and MO-LDH products without any heating operation. The prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Thermogravimetry (TG), Differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM). The products showed high crystallinity phase of Cu-Al and MO intercalated Cu-Al LDH with no evident impurities, proving that the craft introduced here was facile and effective. The new idea can be applied in other fields to produce organic-inorganic composites. - Highlights: • A facile mechanochemical route to synthesize Cu-Al and MO intercalated Cu-Al LDH. • The products possesses high crystalline of LDH phase with no impure phases. • The dry milling process induces the element substitution between the raw materials. • The agitation operation helps the grain growth of LDH.

  7. Mechanochemical synthesis of Cu-Al and methyl orange intercalated Cu-Al layered double hydroxides

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Jun, E-mail: forsjun@whut.edu.cn [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); He, Xiaoman; Chen, Min; Hu, Huimin [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); Zhang, Qiwu, E-mail: zhangqw@whut.edu.cn [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); Liu, Xinzhong [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350118 China (China)

    2017-04-15

    In this study, a mechanochemical route to synthesize a Cu-Al layered double hydroxide (LDH) and a methyl orange (MO) intercalated one (MO-LDH) was introduced, in which basic cupric carbonate (Cu{sub 2}(OH){sub 2}CO{sub 3}) and aluminum hydroxide (Al(OH){sub 3}) with Cu/Al molar ratio at 2/1 was first dry ground for 2 h and then agitated in water or methyl orange solution for another 4 h to obtain the LDH and MO-LDH products without any heating operation. The prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Thermogravimetry (TG), Differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM). The products showed high crystallinity phase of Cu-Al and MO intercalated Cu-Al LDH with no evident impurities, proving that the craft introduced here was facile and effective. The new idea can be applied in other fields to produce organic-inorganic composites. - Highlights: • A facile mechanochemical route to synthesize Cu-Al and MO intercalated Cu-Al LDH. • The products possesses high crystalline of LDH phase with no impure phases. • The dry milling process induces the element substitution between the raw materials. • The agitation operation helps the grain growth of LDH.

  8. Superstructure formation in PrNi_2Al_3 and ErPd_2Al_3

    International Nuclear Information System (INIS)

    Eustermann, Fabian; Hoffmann, Rolf-Dieter; Janka, Oliver; Oldenburg Univ.

    2017-01-01

    The intermetallic phase ErPd_2Al_3 was obtained by arc-melting of the elements and subsequent annealing for crystal growth. The sample was studied by X-ray diffraction on powders and single crystals. The structure of ErPd_2Al_3 was refined from X-ray diffraction data and revealed a superstructure of PrNi_2Al_3 - a CaCu_5 derivative (P6/m, a=1414.3(1), c=418.87(3) pm wR=0.0820, 1060 F"2 values, 48 variables). The same superstructure was subsequently found for PrNi_2Al_3 (P6/m, a=1407.87(4), c=406.19(2) pm, wR=0.0499, 904 F"2 values, 47 variables). In the crystal structure, the aluminium and transition metal atoms form a polyanionic network according to [T_2Al_3]"δ"-, while rare earth atoms fill cavities within the networks. They are coordinated by six transition metal and twelve aluminum atoms. In contrast to the PrNi_2Al_3 type structure reported so far, two crystallographic independent rare-earth sites are found of which one (1b) is shifted by 1/2 z, causing a distortion in the structure along with a recoloring of the T and Al atoms in the network.

  9. Derecho humano al agua y al saneamiento: derechos estrechamente vinculados al derecho a la vida

    OpenAIRE

    Fernández Aller, Maria Celia; Luis Romero, Elena de; Guzmán Acha, Cristina

    2013-01-01

    Los derechos humanos al agua y al saneamiento están íntimamente relacionados con otros derechos esenciales para la vida, como la alimentación o la salud. Su reconocimiento como derechos humanos en 2010 marca un hito importante en el respeto, protección y realización de estos derechos, que se encuentran seriamente vulnerados para una mayoría de población más vulnerable y empobrecida, sobre todo en el ámbito rural. Mucho camino queda aún para conseguir no sólo la disponibilidad de agua y saneam...

  10. Deformation mechanisms of nanotwinned Al

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xinghang [Texas A & M Univ., College Station, TX (United States)

    2016-11-10

    The objective of this project is to investigate the role of different types of layer interfaces on the formation of high density stacking fault (SF) in Al in Al/fcc multilayers, and understand the corresponding deformation mechanisms of the films. Stacking faults or twins can be intentionally introduced (via growth) into certain fcc metals with low stacking fault energy (such as Cu, Ag and 330 stainless steels) to achieve high strength, high ductility, superior thermal stability and good electrical conductivity. However it is still a major challenge to synthesize these types of defects into metals with high stacking fault energy, such as Al. Although deformation twins have been observed in some nanocrystalline Al powders by low temperature, high strain rate cryomilling or in Al at the edge of crack tip or indentation (with the assistance of high stress intensity factor), these deformation techniques typically introduce twins sporadically and the control of deformation twin density in Al is still not feasible. This project is designed to test the following hypotheses: (1) Certain type of layer interfaces may assist the formation of SF in Al, (2) Al with high density SF may have deformation mechanisms drastically different from those of coarse-grained Al and nanotwinned Cu. To test these hypotheses, we have performed the following tasks: (i) Investigate the influence of layer interfaces, stresses and deposition parameters on the formation and density of SF in Al. (ii) Understand the role of SF on the deformation behavior of Al. In situ nanoindentation experiments will be performed to probe deformation mechanisms in Al. The major findings related to the formation mechanism of twins and mechanical behavior of nanotwinned metals include the followings: 1) Our studies show that nanotwins can be introduced into metals with high stacking fault energy, in drastic contrast to the general anticipation. 2) We show two strategies that can effectively introduce growth twins in

  11. Deformation mechanisms of nanotwinned Al

    International Nuclear Information System (INIS)

    Zhang, Xinghang

    2016-01-01

    The objective of this project is to investigate the role of different types of layer interfaces on the formation of high density stacking fault (SF) in Al in Al/fcc multilayers, and understand the corresponding deformation mechanisms of the films. Stacking faults or twins can be intentionally introduced (via growth) into certain fcc metals with low stacking fault energy (such as Cu, Ag and 330 stainless steels) to achieve high strength, high ductility, superior thermal stability and good electrical conductivity. However it is still a major challenge to synthesize these types of defects into metals with high stacking fault energy, such as Al. Although deformation twins have been observed in some nanocrystalline Al powders by low temperature, high strain rate cryomilling or in Al at the edge of crack tip or indentation (with the assistance of high stress intensity factor), these deformation techniques typically introduce twins sporadically and the control of deformation twin density in Al is still not feasible. This project is designed to test the following hypotheses: (1) Certain type of layer interfaces may assist the formation of SF in Al, (2) Al with high density SF may have deformation mechanisms drastically different from those of coarse-grained Al and nanotwinned Cu. To test these hypotheses, we have performed the following tasks: (i) Investigate the influence of layer interfaces, stresses and deposition parameters on the formation and density of SF in Al. (ii) Understand the role of SF on the deformation behavior of Al. In situ nanoindentation experiments will be performed to probe deformation mechanisms in Al. The major findings related to the formation mechanism of twins and mechanical behavior of nanotwinned metals include the followings: 1) Our studies show that nanotwins can be introduced into metals with high stacking fault energy, in drastic contrast to the general anticipation. 2) We show two strategies that can effectively introduce growth twins in

  12. Study on Microstructure and Mechanical Properties of Hypereutectic Al-18Si Alloy Modified with Al-3B.

    Science.gov (United States)

    Gong, Chunjie; Tu, Hao; Wu, Changjun; Wang, Jianhua; Su, Xuping

    2018-03-20

    An hypereutectic Al-18Si alloy was modified via an Al-3B master alloy. The effect of the added Al-3B and the modification temperature on the microstructure, tensile fracture morphologies, and mechanical properties of the alloy were investigated using an optical microscope, Image-Pro Plus 6.0, a scanning electron microscope, and a universal testing machine. The results show that the size of the primary Si and its fraction decreased at first, and then increased as an additional amount of Al-3B was added. When the added Al-3B reached 0.2 wt %, the fraction of the primary Si in the Al-18Si alloy decreased with an increase in temperature. Compared with the unmodified Al-18Si alloy, the tensile strength and elongation of the alloy modified at 850 °C with 0.2 wt % Al-3B increased by 25% and 81%, respectively. The tensile fracture of the modified Al-18Si alloy exhibited partial ductile fracture characteristics, but there were more areas with ductile characteristics compared with that of the unmodified Al-18Si alloy.

  13. 26Mg(p,n)26Al and 23Na(α,n)26Al reactions

    International Nuclear Information System (INIS)

    Skelton, R.T.

    1985-01-01

    Cross sections for the 26 Mg(p,n) 26 Al reaction were measured from threshold at 4.988 MeV to 5.820 MeV. Cross sections for the 23 Na(α,n) 26 Al reaction were measured from threshold at 3.483 MeV to 4.597 MeV. In each case, separate measurements were to the ground state and to the first and second excited states of 26 Al. Cross sections for the inverse reactions were calculated and reaction rate factors relating to the destruction of 26 Al in a supernova environment were determined. Astrophysical implications relating to the observation of live and extinct 26 Al are discussed. Excitation functions for several additional exit channels for the 26 Mg + rho and 23 Na + α reactions are reported

  14. effect of the parameters of AlN/GaN/AlGaN and AlN/GaN/InAlN heterostructures with a two-dimensional electron gas on their electrical properties and the characteristics of transistors on their basis

    Energy Technology Data Exchange (ETDEWEB)

    Tsatsulnikov, A. F., E-mail: andrew@beam.ioffe.ru [Russian Academy of Sciences, Submicron Heterostructures for Microelectronics Research and Engineering Center (Russian Federation); Lundin, V. W.; Zavarin, E. E.; Yagovkina, M. A.; Sakharov, A. V. [Russian Academy of Sciences, Ioffe Physical–Technical Institute (Russian Federation); Usov, S. O. [Russian Academy of Sciences, Submicron Heterostructures for Microelectronics Research and Engineering Center (Russian Federation); Zemlyakov, V. E.; Egorkin, V. I. [National Research University of Electronic Technology (MIET) (Russian Federation); Bulashevich, K. A.; Karpov, S. Yu. [“Soft-Impact” Ltd. (Russian Federation); Ustinov, V. M. [Russian Academy of Sciences, Submicron Heterostructures for Microelectronics Research and Engineering Center (Russian Federation)

    2016-10-15

    The effect of the layer thickness and composition in AlGaN/AlN/GaN and InAlN/AlN/GaN transistor heterostructures with a two-dimensional electron gas on their electrical and the static parameters of test transistors fabricated from such heterostructures are experimentally and theoretically studied. It is shown that the use of an InAlN barrier layer instead of AlGaN results in a more than twofold increase in the carrier concentration in the channel, which leads to a corresponding increase in the saturation current. In situ dielectric-coating deposition on the InAlN/AlN/GaN heterostructure surface during growth process allows an increase in the maximum saturation current and breakdown voltages while retaining high transconductance.

  15. Fabrication and thermal characterization of amorphous and nanocrystalline Al{sub 9}FeNi/Al{sub 3}Ti compound

    Energy Technology Data Exchange (ETDEWEB)

    Tavoosi, Majid, E-mail: ma.tavoosi@gmail.com

    2017-01-15

    In this study, the fabrication and structural characterization of amorphous/nanocrystalline Al{sub 9}FeNi/Al{sub 3}Ti phase has been performed. In this regards, milling and annealing processes were applied on Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} (at. %) powder mixture for different periods of time. The prepared samples were characterized using X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM and TEM) and differential scanning calorimetery (DSC). According to the results, supersaturated solid solution, nanocrystalline Al{sub 9}FeNi/Al{sub 3}Ti (with average crystallite size of about 7 nm) and amorphous phases indicated three different microstructures which can be formed in Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} system during milling process. The formed supersaturated solid solution and amorphous phases were unstable and transformed to Al{sub 9}FeNi/Al{sub 3}Ti intermetallic compound during annealing process. It is shown that, Al{sub 9}FeNi phase in Al{sub 9}FeNi/Al{sub 3}Ti intermetallic compound can decompose into Al{sub 3}Ni, Al{sub 13}Fe{sub 4} and liquid phases during a reversible peritectic reaction at 809 °C. - Highlights: • We study the effect of milling process on Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} alloy. • We study the effect of annealing on Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} supersaturated solid solution phase. • We study the effect of annealing on Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} amorphous phase. • We study the thermal behaviour of Al{sub 9}FeNi/Al{sub 3}Ti compound.

  16. Computer aided cooling curve analysis for Al-5Si and Al-11Si alloys ...

    African Journals Online (AJOL)

    The effect of grain refiner, modifier, and combination of grain refiner cum modifier was studied on Al-5Si and Al-11Si alloys using computer aided cooling curve analysis. For combined grain refinement and modification effect, Al-Ti-B-Sr single master alloy was developed that acted as both grain refiner and modifier.

  17. AL-USRCRN Station Information

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Documentation of United States Alabama Regional Climate Reference Network (AL-USRCRN) installations in 2006. Installations documented are for AL-USRCRN pilot project...

  18. Gd3+-ESR and magnetic susceptibility of GdCu4Al8 and GdMn4Al8

    International Nuclear Information System (INIS)

    Coldea, R.; Coldea, M.; Pop, I.

    1994-01-01

    Gd ESR of GdCu 4 Al 8 and GdMn 4 Al 8 and magnetic susceptibility of GdCu 4 Al 8 , GdMn 4 Al 8 , and YMn 4 Al 8 were measured in the temperature range of 290K--460K and 90K--1050K, respectively. The occurrence of the Mn moment in YMn 4 Al 8 and GdMn 4 Al 8 is strongly correlated with the critical value of d∼2.6 angstrom of the Mn-Mn distance below which the Mn moment is not stable. The experimental data for GdMn 4 Al 8 , compared with the data for the isostructural compounds GdCu 4 Al 8 and YMn 4 Al 8 , show that near the critical value of d, the existence of Mn moment depends not only on the value of d, but also on the local magnetic surroundings. It has been revealed that the magnetic character of Mn moment in YMn 4 Al 8 and GdMn 4 Al 8 changes from an itinerant electron type to a local-moment type with increasing temperature

  19. Effect of AlB2-Mg interaction on the mechanical properties of Al-based composites

    International Nuclear Information System (INIS)

    Calderon, Hermes E.; Hidalgo, Ruth G.I.; Melgarejo, Z. Humberto; Suarez, O. Marcelo

    2010-01-01

    A series of Al-based composites with a matrix containing 2.5 wt.%Cu and 1 wt.%Mg, and reinforced with Al diborides was manufactured and characterized via microscopy and mechanical testing. The impact resistance of the composites revealed interaction between AlB 2 dispersoids and Mg originally present in the Al matrix. An unexpected increase in the absorbed impact energy of composites with diborides prompted complementary experiments leading to this finding. Hardness tests were correlated to those results and provided further evidence of the interaction between Mg and the dispersoids. Additional energy dispersive spectroscopy (EDS) analysis and X-ray diffraction tests supported with crystal modeling demonstrated that Mg effectively diffused into the AlB 2 crystal producing a doped structure with an Al 1-x Mg x B 2 formula where x lies between 0.08 and 0.15.

  20. Potential skin involvement in ALS: revisiting Charcot's observation - a review of skin abnormalities in ALS.

    Science.gov (United States)

    Paré, Bastien; Gros-Louis, François

    2017-07-26

    Amyotrophic lateral sclerosis (ALS) is a neurodegenerative disease affecting motor neurons of the brain and spinal cord, leading to progressive paralysis and death. Interestingly, many skin changes have been reported in ALS patients, but never as yet fully explained. These observations could be due to the common embryonic origin of the skin and neural tissue known as the ectodermal germ layer. Following the first observation in ALS patients' skin by Dr Charcot in the 19th century, in the absence of bedsores unlike other bedridden patients, other morphological and molecular changes have been observed. Thus, the skin could be of interest in the study of ALS and other neurodegenerative diseases. This review summarizes skin changes reported in the literature over the years and discusses about a novel in vitro ALS tissue-engineered skin model, derived from patients, for the study of ALS.

  1. Effects of O in a binary-phase TiAl-Ti3Al alloy: from site occupancy to interfacial energetics

    International Nuclear Information System (INIS)

    Wei Ye; Xu Huibin; Zhou Hongbo; Zhang Ying; Lu Guanghong

    2011-01-01

    We have investigated site occupancy and interfacial energetics of a TiAl-Ti 3 Al binary-phase system with O using a first-principles method. Oxygen is shown to energetically occupy the Ti-rich octahedral interstitial site, because O prefers to bond with Ti rather than Al. The occupancy tendency of O in TiAl alloy from high to low is α 2 -Ti 3 Al to the γ-α 2 interface and γ-TiAl. We demonstrate that O can largely affect the mechanical properties of the TiAl-Ti 3 Al system. Oxygen at the TiAl-Ti 3 Al interface reduces both the cleavage energy and the interface energy, and thus weakens the interface strength but strongly stabilizes the TiAl/Ti 3 Al interface with the O 2 molecule as a reference. Consequently, the mechanical property variation of TiAl alloy due to the presence of O not only depends on the number of TiAl/Ti 3 Al interfaces but also is related to the O concentration in the alloy.

  2. A study on wear resistance and microcrack of the Ti{sub 3}Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

    Energy Technology Data Exchange (ETDEWEB)

    Li Jianing, E-mail: ljnljn1022@163.com [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China); Chen Chuanzhong [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China); Squartini, Tiziano [INFM-Department of Physics, Siena University, Siena 53100 (Italy); He Qingshan [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China)

    2010-12-15

    Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti{sub 3}Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti{sub 3}Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti{sub 3}Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti{sub 3}Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.

  3. Synthesis behavior of nanocrystalline Al-Al2O3 composite during low time mechanical milling process

    International Nuclear Information System (INIS)

    Alizadeh, Mostafa; Aliabadi, Morteza Mirzaei

    2011-01-01

    Research highlights: → In the low time milling the effect of Al 2 O 3 amount is investigated → Al 2 O 3 particles are distributed uniformly in the Al matrix → In the low time milling it is possible to produce nanostructured composite powder → Median size and bulk density measurements demonstrate reaching the steady state. - Abstract: In this work, four different volume fractions of Al 2 O 3 (10, 20, 30 and 40 vol.%) were mixed with the fine Al powder and the powder blends were milled for 5 h. Scanning electron microscopy analysis, particle size analysis and bulk density measurements were used to investigate the morphological changes and achieving the steady state conditions. The results showed that increasing the Al 2 O 3 content can provide the steady state particle size in 5 h milling process. It was found that increasing the volume fraction of Al 2 O 3 leads to increasing the uniformity of Al 2 O 3 . Standard deviations of microhardness measurements confirmed this result. The XRD pattern and XRF investigations depicted that increasing the Al 2 O 3 content causes an increase in the crystal defects, micro-strain and Fe contamination during 5 h milling process of nanocrystalline composite powders while the grain size is decreased. To investigate the effect of milling time, Al-30 vol.% Al 2 O 3 (which achieved steady state during 5 h milling process) was milled for 1-4 h. The results depicted that the milling time lower than 5 h, do not achieve to steady state conditions.

  4. Study of the ternary alloy systems Al-Ni-Fe and Al-Cu-Ru with special regard to quasicrystalline phases

    International Nuclear Information System (INIS)

    Lemmerz, U.

    1996-07-01

    Two ternary alloy-systems, the Al-Ni-Fe system and the Al-Cu-Ru system were studied with special regard to quasicrystalline phases. Isothermal sections were established in both systems in the stoichiometric area of the quasicrystalline phase. In the Al-Ni-Fe system a new stable decagonal phase was found. Its stoichiometric range is very small around Al 71.6 Ni 23.0 Fe 5.4 . The temperature range in which it is stable lies between 847 and 930 C. The decagonal phase undergoes a eutectoid reaction to the three crystalline phases Al 3 Ni 2 , Al 3 Ni and Al 13 Fe 4 at 847 C. It melts peritectically at 930 C forming Al 13 Fe 4 , Al 3 Ni 2 and a liquid. The investigations in the Al-Cu-Ru system concentrated on the phase equilibria between the icosahedral phase and its neighbouring phases in a temperature range between 600 and 1000 C. The icosahedral phase was observed in the whole temperature range. The investigated stoichiometric area extends down to Al contents of 45%, which allows the fields of existence to be determined for the ternary phases α-AlCuRu, the icosahedral phase and Al 7 Cu 2 Ru. Binary phases were determined down to the upper (high Al content) border of AlRu. No hitherto unknown phase was observed in the investigated area. Rietveld analyses were carried out on α-AlCuRu and Al 7 Cu 2 Ru showing some discrepancies from the α-AlMnSi structure taken as a base for α-AlCuRu and confirming the Al 7 Cu 2 Fe structure for Al 7 Cu 2 Ru. (orig.)

  5. Al-Cu-Li and Al-Mg-Li alloys: Phase composition, texture, and anisotropy of mechanical properties (Review)

    Science.gov (United States)

    Betsofen, S. Ya.; Antipov, V. V.; Knyazev, M. I.

    2016-04-01

    The results of studying the phase transformations, the texture formation, and the anisotropy of the mechanical properties in Al-Cu-Li and Al-Mg-Li alloys are generalized. A technique and equations are developed to calculate the amounts of the S1 (Al2MgLi), T1 (Al2CuLi), and δ' (Al3Li) phases. The fraction of the δ' phase in Al-Cu-Li alloys is shown to be significantly higher than in Al-Mg-Li alloys. Therefore, the role of the T1 phase in the hardening of Al-Cu-Li alloys is thought to be overestimated, especially in alloys with more than 1.5% Li. A new model is proposed to describe the hardening of Al-Cu-Li alloys upon aging, and the results obtained with this model agree well with the experimental data. A texture, which is analogous to that in aluminum alloys, is shown to form in sheets semiproducts made of Al-Cu-Li and Al-Mg-Li alloys. The more pronounced anisotropy of the properties of lithium-containing aluminum alloys is caused by a significant fraction of the ordered coherent δ' phase, the deformation mechanism in which differs radically from that in the solid solution.

  6. Pornographie als Metapher

    Directory of Open Access Journals (Sweden)

    Caroline Schubarth

    2010-03-01

    Full Text Available In diesem Artikel werden unterschiedliche metaphorische Verwendungen des Pornografiebegriffs und deren Implikationen untersucht. Während die Existenz von Pornografie der feministischen Anti-Porno-Bewegung als Erklärung für die anhaltende Diskriminierung von Frauen in westlichen Gesellschaften dient, nutzen rechtskonservative Kräfte den Pornografievorwurf als Rechtfertigung für die Zensur von als deviant empfundenen Identitäten und sexuellen Praktiken.This article examines different metaphorical uses of the term pornography and the resulting implications. While the existence of pornography for the feminist anti-porno movement serves as factor in the continuing discrimination of women in western societies, conservative powers on the right use the allegation of pornography as a justification for censorship of those identities and sexual practices deemed deviant.

  7. Strain Balanced AlGaN/GaN/AlGaN nanomembrane HEMTs.

    Science.gov (United States)

    Chang, Tzu-Hsuan; Xiong, Kanglin; Park, Sung Hyun; Yuan, Ge; Ma, Zhenqiang; Han, Jung

    2017-07-25

    Single crystal semiconductor nanomembranes (NM) are important in various applications such as heterogeneous integration and flexible devices. This paper reports the fabrication of AlGaN/GaN NMs and NM high electron mobility transistors (HEMT). Electrochemical etching is used to slice off single-crystalline AlGaN/GaN layers while preserving their microstructural quality. A double heterostructure design with a symmetric strain profile is employed to ensure minimal residual strain in freestanding NMs after release. The mobility of the two-dimensional electron gas (2DEG), formed by the AlGaN/GaN heterostructure, is noticeably superior to previously reported values of many other NMs. AlGaN/GaN nanomembrane HEMTs are fabricated on SiO 2 and flexible polymeric substrates. Excellent electrical characteristics, including a high ON/OFF ratio and transconductance, suggest that III-Nitrides nanomembranes are capable of supporting high performance applications.

  8. Validated thermodynamic prediction of AlP and eutectic (Si) solidification sequence in Al-Si cast alloys

    International Nuclear Information System (INIS)

    Liang, S M; Schmid-Fetzer, R

    2016-01-01

    The eutectic microstructure in hypoeutectic Al-Si cast alloys is strongly influenced by AlP particles which are potent nuclei for the eutectic (Si) phase. The solidification sequence of AlP and (Si) phases is, thus, crucial for the nucleation of eutectic silicon with marked impact on its morphology. This study presents this interdependence between Si- and P-compositions, relevant for Al-Si cast alloys, on the solidification sequence of AlP and (Si). These data are predicted from a series of thermodynamic calculations. The predictions are based on a self-consistent thermodynamic description of the Al-Si-P ternary alloy system developed recently. They are validated by independent experimental studies on microstructure and undercooling in hypoeutectic Al-Si alloys. A constrained Scheil solidification simulation technique is applied to predict the undercooling under clean heterogeneous nucleation conditions, validated by dedicated experimental observations on entrained droplets. These specific undercooling values may be very large and their quantitative dependence on Si and P content of the Al alloy is presented. (paper)

  9. Phase diagrams of aluminium alloys of Al-Cu-Mg, Al-Mg-Si-Cu, and Al-Mg-Li system

    International Nuclear Information System (INIS)

    Ber, L.B.; Kaputkin, E.Ya.

    2001-01-01

    Isothermal diagrams of phase transformations (DPT) and temperature-time charts (TTC) of variation of electric conductivity and of mechanical features at tension were plotted following thermal treatment according to the pattern of direct hardening and ageing and according to the pattern of normal aging for D16 commercial alloy, Al-Cu-Mg model alloy of the same system, AD37 commercial alloys of Al-Mg-Si-Cu and 1424 one of Al-Li-Mg system. Phase transformations were studied by means of fluorescence electron microscopy, micro-X-ray spectral analysis, X-ray phase analysis of single crystals and polycrystals and differential scanning calorimetry. For every alloy comparison of TTC and DPT enables to clarity the mechanism of phase composition effect on features and to optimize conditions of hardening cooling and ageing [ru

  10. Superhydrophobic ZnAl double hydroxide nanostructures and ZnO films on Al and glass substrates

    Energy Technology Data Exchange (ETDEWEB)

    De, Debasis, E-mail: debasis.de@bcrec.ac.in [Electronics and Instrumentation Engineering Department, Dr. B C Roy Engineering College, Durgapur, West Bengal 713206 (India); Sarkar, D.K. [Centre Universitaire de Recherche sur l' Aluminium (CURAL), L' Université du Québec à Chicoutimi, 555 Blvd. Université, Chicoutimi, Saguenay, Québec G7H 2B1 (Canada)

    2017-01-01

    Superhydrophobic nanostructured ZnAl: layered double hydroxides (LDHs) and ZnO films have been fabricated on Al and glass substrates, respectively, by a simple and cost effective chemical bath deposition technique. Randomly oriented hexagonal patterned of ZnAl: LDHs thin nanoplates are clearly observed on Al-substrate in the scanning electron microscopic images. The average size of these hexagonal plates is ∼4 μm side and ∼30 nm of thickness. While on the glass substrate, a oriented hexagonal patterned ZnO nanorods (height ∼5 μm and 1 μm diameter) are observed and each rod is further decorated throughout the top few nanometers with several nanosteps. At the top of the nanorod, a perfectly hexagonal patterned ZnO surface with ∼250 nm sides is observed. The tendency to form hexagonal morphological features is due to the hexagonal crystal structure of ZnO confirmed from X-ray diffraction patterns and transmission electron microscopy image. The ZnAl: LDHs and/or ZnO coated substrates have been passivated by using stearic acid (SA) molecules. Infrared spectra of passivated ZnAl: LDHs coated substrates confirm the presence of SA. X-ray diffraction pattern also corroborates the results of infrared spectrum. The contact angle of the as prepared samples is zero. The superhydrophobicity is achieved by observing contact angle of ∼161° with a hysteresis of ∼4° for Al-substrate. On the glass substrate, a higher contact angle of ∼168° with a lower hysteresis of ∼3° is observed. A lower surface roughness of ∼4.93 μm is measured on ZnAl: LDHs surface layer on the Al substrate as compare to a higher surface roughness of 6.87 μm measured on ZnO layer on glass substrate. The superhydrophobicity of passivated nanostructured films on two different substrates is observed due to high surface roughness and low surface energy. - Highlights: • ZnAl: layered double hydroxides (LDHs) nanoplates are fabricated on Al substrate. • ZnO nanorods are fabricated on

  11. Formation of Nb3Al in powder processed Nb-Al superconductors

    International Nuclear Information System (INIS)

    Johnson, P.E.

    1987-05-01

    In high magnetic fields, the critical current density is strongly dependent on the upper critical field, which is determined primarily by the stoichiometry of the Nb 3 Al. The critical temperature (T/sub c/), like the upper critical field, is considered to be a measure of the ''intrinsic'' quality of the superconductor, indicating the stoichiometry, order, and strain. If the A15 phase is stoichiometric and well ordered, a high T/sub c/ (and high H/sub C 2 /) is expected, regardless of the volume fraction of superconductor. On the other hand, if sigma phase is present with the A15, the resultant composition gradient across the sigma-A15 interface(s) requires that some of the A15 be off-stoichiometric, and therefore that the T/sub c/ (and H/sub C 2 /) be low. Thus the extent of the A15 (Nb 3 Al) reaction and the quality of the A15 formed are interdependent. This work focuses on the factors that control the extent of Nb 3 Al formation in Nb/Al powder wires. The morphology and content of the reacted and unreacted wires are studied in optical, SEM, and TEM micrographs. Critical current density data and its dependence on processing are explained in terms of the unreacted microstructure and its effect on the extent of Nb 3 Al formation. As a method of improving the critical current density, a new variation of the conventional powder process for wire manufacturing is developed and tested

  12. Al-Si/B{sub 4}C composite coatings on Al-Si substrate by plasma spray technique

    Energy Technology Data Exchange (ETDEWEB)

    Sarikaya, Ozkan [Sakarya University, Faculty of Engineering, Department of Mechanical Engineering, Esentepe Campus, Sakarya 54187 (Turkey); Anik, Selahaddin [Sakarya University, Faculty of Engineering, Department of Mechanical Engineering, Esentepe Campus, Sakarya 54187 (Turkey); Aslanlar, Salim [Sakarya University, Faculty of Technical Education, Department of Mechanical Engineering, Esentepe Campus, Sakarya 54187 (Turkey); Cem Okumus, S. [Sakarya University, Faculty of Engineering, Department of Metallurgical and Materials Engineering, Esentepe Campus, Sakarya 54187 (Turkey); Celik, Erdal [Dokuz Eylul University, Engineering Faculty, Department of Metallurgical and Materials Engineering, Buca, Izmir 35160 (Turkey)]. E-mail: erdal.celik@deu.edu.tr

    2007-07-01

    Plasma-sprayed coatings of Al-Si/B{sub 4}C have been prepared on Al-Si piston alloys for diesel engine motors. The Al-Si/B{sub 4}C composite powders including 5-25 wt% B{sub 4}C were prepared by mixing and ball-milling processes. These powders were deposited on Al-Si substrate using an atmospheric plasma spray technique. The coatings have been characterised with respect to phase composition, microstructure, microhardness, bond strength and thermal expansion. It was found that Al, Si, B{sub 4}C and Al{sub 2}O{sub 3} phases were determined in the coatings with approximately 600 {mu}m thick by using X-ray diffraction analysis. Scanning electron microscope observation revealed that boron carbide particles were uniformly distributed in composite coatings and B{sub 4}C particles were fully wetted by Al-Si alloy. Also, no reaction products were observed in Al-Si/B{sub 4}C composite coatings. It was found that surface roughness, porosity, bond strength and thermal expansion coefficient of composite coatings decreased with increasing fraction of the boron carbide particle. It was demonstrated that the higher the B{sub 4}C content, the higher the hardness of coatings because the hardness of B{sub 4}C is higher than that of Al-Si.

  13. Fluctuations of charge variance and interaction time for dissipative processes in 27 Al + 27 Al collision

    International Nuclear Information System (INIS)

    Berceanu, I.; Andronic, A.; Duma, M.

    1999-01-01

    The systematic studies of dissipative processes in light systems were completed with experiments dedicated to the measurement of the excitation functions in 19 F + 27 Al and 27 Al + 27 Al systems in order to obtain deeper insight on DNS configuration and its time evolution. The excitation function for 19 F + 27 Al system evidenced fluctuations larger than the statistical errors. Large Z and angular cross correlation coefficients supported their non-statistical nature. The energy dependence of second order observables, namely the second moment of the charge distribution and the product ω·τ (ω - the angular velocity of the DNS and τ its mean lifetime) extracted from the angular distributions were studied for 19 F + 27 Al case. In this contribution we are reporting the preliminary results of similar studies performed for 27 Al + 27 Al case. The variance of the charge distribution were obtained fitting the experimental charge distribution with a Gaussian centered on Z = 13 and the product ω·τ was extracted from the angular distributions. The results for 19 F + 27 Al case are confirmed by a preliminary analysis of the data for 27 Al + 27 Al system. The charge variance and ω·τ excitation functions for Z = 11 fragment are represented together with the excitation function of the cross section. One has to mention that the data for 27 Al + 27 Al system were not corrected for particle evaporation processes. The effect of the evaporation corrections on the excitation function was studied using a Monte Carlo simulation. The α particle evaporation was also included and the evaluation of the particle separation energies was made using experimental masses of the fragments. The excitation functions for 27 Al + 27 Al system for primary and secondary fragments were simulated. No structure due to particle evaporation was observed. The correlated fluctuations in σ Z and ω·τ excitation functions support a stochastic exchange of nucleons as the main mechanism for

  14. Unprecedented Al supersaturation in single-phase rock salt structure VAlN films by Al+ subplantation

    Science.gov (United States)

    Greczynski, G.; Mráz, S.; Hans, M.; Primetzhofer, D.; Lu, J.; Hultman, L.; Schneider, J. M.

    2017-05-01

    Modern applications of refractory ceramic thin films, predominantly as wear-protective coatings on cutting tools and on components utilized in automotive engines, require a combination of excellent mechanical properties, thermal stability, and oxidation resistance. Conventional design approaches for transition metal nitride coatings with improved thermal and chemical stability are based on alloying with Al. It is well known that the solubility of Al in NaCl-structure transition metal nitrides is limited. Hence, the great challenge is to increase the Al concentration substantially while avoiding precipitation of the thermodynamically favored wurtzite-AlN phase, which is detrimental to mechanical properties. Here, we use VAlN as a model system to illustrate a new concept for the synthesis of metastable single-phase NaCl-structure thin films with the Al content far beyond solubility limits obtained with conventional plasma processes. This supersaturation is achieved by separating the film-forming species in time and energy domains through synchronization of the 70-μs-long pulsed substrate bias with intense periodic fluxes of energetic Al+ metal ions during reactive hybrid high power impulse magnetron sputtering of the Al target and direct current magnetron sputtering of the V target in the Ar/N2 gas mixture. Hereby, Al is subplanted into the cubic VN grains formed by the continuous flux of low-energy V neutrals. We show that Al subplantation enables an unprecedented 42% increase in metastable Al solubility limit in V1-xAlxN, from x = 0.52 obtained with the conventional method to 0.75. The elastic modulus is 325 ± 5 GPa, in excellent agreement with density functional theory calculations, and approximately 50% higher than for corresponding films grown by dc magnetron sputtering. The extension of the presented strategy to other Al-ion-assisted vapor deposition methods or materials systems is straightforward, which opens up the way for producing supersaturated single

  15. Erudición y nostalgia. Al-Hanīn ilà l-awtān en el editor de al-Faraŷ ba,d al-šidda de al-Tanūjī

    Directory of Open Access Journals (Sweden)

    Garulo, Teresa

    2012-06-01

    Full Text Available If you want to read a book, a medieval Arabic book, that talks to you about man and his relation with power (God’s power or any kind of worldly power, or about daily life in 10th century Basra or Baghdad, you will probably choose al-Tanūkhī’s works. His Nishwār al-muhādara wa-l-mudhākara or al-Faraj ba,d al-shidda are so widely and so well provided with stories, anecdotes, historical narratives, etc., that you won’t be able to drop it and probably will forget to read the many comments and marginal notes by, Abbūd al-Shāljī, its editor. But if you are wise enough, you will read everything he writes, because you will find in his remarks not only a sustained scholarliness but a fascinating evocation of his life in Irak, mostly in the thirties, with its cooking, manners and customs, and a pang of nostalgia that deserves, I think, at least a note or a friendly comment. In this paper I try to analyse some of his nostalgic memories of Baghdad and its people and places.Uno de los temas clásicos de la literatura árabe, casi desde sus comienzos, es la nostalgia de la tierra natal (al-hanīn ilà l-awtān. Experiencia dolorosa de extrañamiento, que se nutre de las crisis políticas, la nostalgia ha dado lugar a obras que buscan recrear un pasado o unos lugares amados, que sólo la memoria es capaz de recuperar. En este artículo trato de mostrar cómo se articula la nostalgia de Iraq, y, más concretamente, de Bagdad, dentro del aparato crítico de al-Faraŷ ba,da l-šidda de al-Tanūjī (329-384/941-994 (con el apoyo de Nišwār al-muhādara, también de dicho autor en la edición de, Abbūd al-Šālŷī, publicada en los años setenta. La representación que hace al-Tanūjī de la vida cotidiana de la capital abbasí, expresada a través de un lenguaje claro y natural, en el que tienen cabida expresiones populares, suscita en al-Šālŷī toda una serie de remembranzas, sobre todo de sus años juveniles, que se desbordan en sus notas, e

  16. Lou Gehrig's Disease (ALS)

    Science.gov (United States)

    ... disease. Who Gets ALS? Although this disease can strike anyone, ALS is extremely rare in kids. According ... home to provide care that the family cannot handle alone. Living With Lou Gehrig's Disease Living with ...

  17. Difficulties on study of ISM 26Al and a possible new way to nucleosynthesize 26Al-SNIa

    International Nuclear Information System (INIS)

    Peng Qiuhe

    1995-01-01

    Some observational results of the 1.809 MeV gamma-ray emitted by decay of the interstellar medium (ISM) 26 Al, which are obtained by spacecraft during (1979-1992) are firstly introduced. Secondly, both Mg-Al chain and Ne-Na cycle of nuclear reactions are discussed. Thirdly, some new experiments of nuclear physics, which are related with the question of the ISM 26 Al(e.g. measurements of the cross section of the nuclear reactions in the MgAl chain and in the NeNa cycle) are introduced. Then, comparing some experiments of nuclear physics, some difficulties confronted on various models responsible for the ISM 26 Al are discussed. The conclusions are: 1) all of hydrostatic H-burning models and all current nova models are hard to provide enough ISM 26 Al to be detected; 2) SN II + SN I b models are promising on responsibility for the half of ISM 26 Al, although current SN II + SN I b models should be improved, besides. Proposal of a new way to nucleosynthesizse 26 Al, 14 N + 16 O→ 26 Al + α, is suggested. SNI a as a possible source of the ISM 26 Al is discussed (63 refs.)

  18. Effect of the interface in laminated composites of Al-1100 and Al-2024

    International Nuclear Information System (INIS)

    Godefroid, L.B.

    1983-01-01

    Laminated composites consisting of alternating layers of Al-1100 and Al-2024 were produced by hot rolling, with 45% Al-2024 volume fraction. These composites were subjected to cyclic thermal treatment (various numbers of cycles) and to isothermal treatment (various numbers of cycles) and to isothermal treatment (at peak temperature and for times equivalent to those of the thermal cycles. Microhardness, tensile and fatigue crack arrester modes) were studied in the initial state and after treatments. (E.G.) [pt

  19. AlGaN-Based Deep-Ultraviolet Light Emitting Diodes Fabricated on AlN/sapphire Template

    International Nuclear Information System (INIS)

    Li-Wen, Sang; Zhi-Xin, Qin; Hao, Fang; Yan-Zhao, Zhang; Tao, Li; Zheng-Yu, Xu; Zhi-Jian, Yang; Bo, Shen; Guo-Yi, Zhang; Shu-Ping, Li; Wei-Huang, Yang; Hang-Yang, Chen; Da-Yi, Liu; Jun-Yong, Kang

    2009-01-01

    We report on the growth and fabrication of deep ultraviolet (DUV) light emitting diodes (LEDs) on an AlN template which was grown on a pulsed atomic-layer epitaxial buffer layer. Threading dislocation densities in the AlN layer are greatly decreased with the introduction of this buffer layer. The crystalline quality of the AlGaN epilayer is further improved by using a low-temperature GaN interlayer between AlGaN and AlN. Electroluminescences of different DUV-LED devices at a wavelength of between 262 and 317 nm are demonstrated. To improve the hole concentration of p-type AlGaN, Mg-doping with trimethylindium assistance approach is performed. It is found that the serial resistance of DUV-LED decreases and the performance of DUV-LED such as EL properties is improved. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  20. Surface study and thickness control of thin Al2O3 film on Cu-9%Al(111) single crystal

    International Nuclear Information System (INIS)

    Yamauchi, Yasuhiro; Yoshitake, Michiko; Song Weijie

    2004-01-01

    We were successful in growing a uniform flat Al 2 O 3 film on the Cu-9%Al(111) surface using the improved cleaning process, low ion energy and short time sputtering. The growth of ultra-thin film of Al 2 O 3 on Cu-9%Al was investigated using Auger electron spectroscopy (AES) and a scanning electron microscope (SEM). The Al 2 O 3 film whose maximum thickness was about 4.0 nm grew uniformly on the Cu-9%Al surface. The Al and O KLL Auger peaks of Al 2 O 3 film shifted toward low kinetic energy, and the shifts were related to Schottky barrier formation and band bending at the Al 2 O 3 /Cu-9%Al interface. The thickness of Al 2 O 3 film on the Cu-9%Al surface was controlled by the oxygen exposure

  1. Photovoltaic energy conversion and wind power plants creating new jobs; Arbeitsplaetze durch Photovoltaik und Windenergie

    Energy Technology Data Exchange (ETDEWEB)

    Hille, G.; Hoffmann, V.U. [Fraunhofer ISE, Freiburg (Germany); Dienhart, H.; Langniss, O.; Nitsch, J. [DLR, Stuttgart (Germany)

    1997-12-01

    Experts are unanimous that opening up new markets through innovative technologies will be the successful strategy for reversing the upward trend of unemployment in Germany. This approach puts renewable energy sources into the foreground, as enhanced use of wind power and photovoltaic energy conversion will no doubt create new jobs. These technologies will, however, require favourable regulatory framework conditions in order to become a significant force in combatting unemployment. (orig./CB) [Deutsch] Es gilt unter Experten als sicher, dass eine Umkehr am Arbeitsmarkt nur dadurch zu schaffen ist, dass innovative Technologien genutzt und damit neue Maerkte erschlossen werden. Demnach koennte etwa dem Ausbau der regenerativen Energietraeger Wind und Photovoltaik zur Schaffung zukunftssicherer Arbeitsplaetze eine grosse Bedeutung zukommen. Einen ernstzunehmenden Beitrag im Kampf gegen die Arbeitslosigkeit koennen diese Technologien allerdings nur unter bestimmten Rahmenbedingungen leisten. (orig./RHM)

  2. Einsatz von E-Portfolios bei der Qualifizierung pädagogischer Professionals in restriktiven Settings

    Directory of Open Access Journals (Sweden)

    Dirk Jahn

    2010-05-01

    Full Text Available Der Beitrag zeigt den Einsatz von E-Portfolios bei der Qualifizierung pädagogischer Professionals in der beruflichen Bildung auf. Dabei werden als Referenz die Theorie der Selbstreflexion, des kritischen Denkens sowie des Konzeptwandels zugrunde gelegt. Es werden Möglichkeiten aufgezeigt, wie E-Portfolios auch in restriktiven Settings eingesetzt werden können. Bislang dominiert in der Literatur der Einsatz von E-Portfolios in der Schule bzw. in der Bildung von Lehrkräften. Restriktive Settings sind Settings, die für das formale Lernen nur kurze Zeiträume eröffnen, mit heterogenen Zielgruppen verbunden sind und die zum Teil ungünstige motivationale und kognitive Ausgangsvoraussetzungen mitbringen. Die dargestellten Ergebnisse fussen auf der Entwicklung, Erprobung und Erforschung eines solchen Settings, nämlich der Erprobung eines Qualifizierungskonzepts für pädagogische Professionals im Einzelhandel.

  3. Lean management - an effective way to arrange maintenance?; Lean Management - ein effektiver Weg zur Gestaltung der Instandhaltung?

    Energy Technology Data Exchange (ETDEWEB)

    Tschuschke, W. [Inst. fuer Instandhaltung gGmbH, Iserlohn (Germany)

    1996-08-01

    Lean management/lean production wishes to attain more through intelligent operation system/production at less expense (personnel, materials, energy, costs). The object is not harder but more intelligent and production work; we do not need to run faster but to find shorter routes. The idea of lean management`s effects and changes have consequences for the field of maintenance as an equivalent and legitimate business area which are discussed in this paper. (orig.) [Deutsch] Lean Management/Lean Production will durch ein intelligentes Arbeitssystem/Produzieren mit weniger Aufwand (Personal, Material, Energie, Kosten) mehr erreichen. Ziel ist nicht das haertere, sondern das intelligentere und produktivere Arbeiten; wir sollen nicht schneller laufen, sondern kuerzere Wege finden. Fuer den Bereich Instandhaltung als gleichwertiger und gleichberechtigter Unternehmensbereich haben die Gedanken des Lean Managements Auswirkungen und Veraenderungen zur Folge, die im Beitrag genannt werden. (orig.)

  4. Mr. Robot: Schizophrenie, Paranoia und korporative Gier

    Directory of Open Access Journals (Sweden)

    jan jagodzinski

    2016-11-01

    Full Text Available Der vorliegende Beitrag untersucht die erste Staffel von Mr. Robot (2015 − aus Gilles Deleuzes symptomatologischer Position, die sich auf das Spannungsfeld zwischen ‹dem Klinischen und dem Kritischen› fokussiert. Zum Zeitpunkt des Verfassens dieses Artikels war nur die erste Staffel verfügbar. Im Folgenden zeige ich am Beispiel der Hauptfigur Elliot Anderson, inwiefern die Serie Einblicke in unsere ‹Kontrollgesellschaft› – auch eine Deleuzsche Entwicklung – gewähren kann. Zudem wird ein Vergleich mit dem Film «Kein System ist sicher», der ähnliche gesellschaftliche Fragen thematisiert, vorgenommen. Obwohl ich auf medienpädagogische Aspekte nur indirekt eingehen werde, hebe ich im Laufe der Argumentation hervor, dass solche Fernsehnarrative das allgemeine Publikum oder das, was ich als ‹jedermann› beschreibe, mit ethischen Problemen und Dilemmata unserer globalen kapitalistischen Ordnung konfrontieren.

  5. Herausforderungen beim Aufbau und bei der Pflege einer Bilddatenbank – ein Anwendungsbeispiel aus dem Digitalen Forschungsarchiv Byzanz (DiFAB

    Directory of Open Access Journals (Sweden)

    Nina Rannharter

    2017-09-01

    Full Text Available Mit Metadaten versehene, digital archivierte Bilder sind aufgrund ihrer hohen Komplexität eine ständige Herausforderung für den Aufbau von Metadatenstrukturen und für das Beibehalten von adäquaten Metadatenstandards in Bilddatenbanken. Besonders bei Bildern über eine materielle Kultur zeichnet sich diese Komplexität in den diversen Ebenen ab. Zur Verdeutlichung dieser Problematik dient ein einzelnes Monument mit seiner fotographischen Dokumentation als geisteswissenschaftliches Anwendungsbeispiel aus dem Digitalen Forschungsarchiv Byzanz (DiFAB der Universität Wien. Unter der grundsätzlichen Berücksichtigung der künftigen Anforderungen und der einfachen Navigation von Metadaten beinhaltet dieser Beitrag u. a. die Herausforderungen mit den diversen analogen und digitalen Formen der Dokumentation, der historischen Geographie, der kulturspezifischen Terminologie sowie mit der kunsthistorischen Bedeutung einer exakten und unscharfen Datierung für Forschungsarchive.

  6. Microstructural and mechanical properties of Al-Mg/Al{sub 2}O{sub 3} nanocomposite prepared by mechanical alloying

    Energy Technology Data Exchange (ETDEWEB)

    Safari, J., E-mail: safari.jam@gmail.com [Department of Material Science and Engineering, Shahid Bahonar University of Kerman, P.O. Box No. 76135-133, Kerman (Iran, Islamic Republic of); Akbari, G.H. [Department of Material Science and Engineering, Shahid Bahonar University of Kerman, P.O. Box No. 76135-133, Kerman (Iran, Islamic Republic of); Research Center for Mineral Industries, Shahid Bahonar University of Kerman, P.O. Box No. 76135-133, Kerman (Iran, Islamic Republic of); Shahbazkhan, A. [Islamic Azad University, Saveh Branch, Saveh (Iran, Islamic Republic of); Delshad Chermahini, M. [Materials and Energy Research Center, Karaj (Iran, Islamic Republic of)

    2011-09-29

    Highlights: > The presence of Mg has remarkable effects on crystallite size and lattice strain. > The solution of Mg in the Al matrix accelerates the mechanical milling stages. > The microhardness increased in the presence of Mg. > The presence of Mg has significant effect on lattice parameter. > Steady-state situation was occurred in presence of Mg. - Abstract: The effect of milling time on the microstructure and mechanical properties of Al and Al-10 wt.% Mg matrix nanocomposites reinforced with 5 wt.% Al{sub 2}O{sub 3} during mechanical alloying was investigated. Steady-state situation was occurred in Al-10Mg/5Al{sub 2}O{sub 3} nanocomposite after 20 h, due to solution of Mg into Al matrix, while the situation was not observed in Al/5Al{sub 2}O{sub 3} nanocomposite at the same time. For the binary Al-Mg matrix, after 10 h, the predominant phase was an Al-Mg solid solution with an average crystallite size 34 nm. Up to 10 h, the lattice strain increased to about 0.4 and 0.66% for Al and Al-Mg matrix, respectively. The increasing of lattice parameter due to dissolution of Mg atom into Al lattice during milling was significant. By milling for 10 h the dramatic increase in microhardness (155 HV) for Al-Mg matrix nanocomposite was caused by grain refinement and solid solution formation. From 10 to 20 h, slower rate of increasing in microhardness may be attributed to the completion of alloying process, and dynamic and static recovery of powders.

  7. Different magnetic behaviour of the Kondo compounds Al3Ce and Al11Ce3

    International Nuclear Information System (INIS)

    Benoit, A.; Flouquet, J.; Palleau, J.; Buevoz, J.L.

    1979-08-01

    Neutron diffraction experiments on the Al 3 Ce and Al 11 Ce 3 compounds have been performed on the multidetector of the I.L.L. high flux reactor. No magnetic structure has been detected on the Al 3 Ce compound down to 20 mK. This confirms the non magnetic ground state of Al 3 Ce. For Al 11 Ce 3 , two magnetic structures have been observed: a ferromagnetic one at 4.2 K and an antiferromagnetic one at 2 K. The antiferromagnetic structure, which corresponds to a propagation vector (0,0,1/3), implies a strong reduction of the magnetic moment of determined sites; this reflects the Kondo character of the compounds

  8. Das Unsichtbare sichtbar machen. Zum vergessenen Beitrag der alten deutschen Frauenbewegung zur Wohn- und Siedlungsreform im frühen 20. Jahrhundert

    Directory of Open Access Journals (Sweden)

    Claudia Wucherpfennig

    2007-03-01

    Full Text Available Der Wohnungs- und Städtebau der Moderne gilt weitgehend als eine „Männerdomäne”. In ihrer Schrift Die Wohnungsfrage ist Frauensache! zeigen Ulla Terlinden und Susanna von Oertzen demgegenüber die vielfältigen und einflussreichen Beiträge der alten deutschen Frauenbewegung zur Wohnungsreform des frühen 20. Jahrhunderts und zum Neuen Bauen auf.

  9. Cast AlSi9Cu4 alloy with hybride strenghtened by Fe{sub x}Al{sub y}-Al{sub 2}O{sub 3} composite powder

    Energy Technology Data Exchange (ETDEWEB)

    Piatkowski, J [Department of Materials Technology, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice (Poland); Formanek, B, E-mail: jaroslaw.piatkowski@polsl.pl, E-mail: boleslaw.formanek@polsl.pl [Department of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice (Poland)

    2011-05-15

    The main objective of the study was to develop a technology of dispersion strenghtened hypoeutectic Al-Si alloy. The article presented the materials and technology conception for producing aluminium matrix composite AlSi9Cu4Fe alloy with hybride reinforcement of Al{sub x}Fe{sub y} intermetallic and aluminium oxide powders. Composite powder obtained in mechanical agllomerisation mixture of elemental powders. Changes in the structure were confirmed by TA and ATD thermal analyses plotting the solidification curves, which showed a decrease in temperature T{sub liq} compared to the unmodified alloy and an exothermic effect originating from the crystallisation of eutectics with alloying elements. The examinations carried out by SEM and BSE as well as the determination of local chemical composition by EDX technique have characterised the structure of the alloy as containing some binary Al-Si-Al-Cu and Al-Fe eutectics and multicomponent eutectics.

  10. Optical microcavities and enhanced electroluminescence from electroformed Al-Al{sub 2}O{sub 3}-Ag diodes

    Energy Technology Data Exchange (ETDEWEB)

    Hickmott, T. W. [Department of Physics, State University of New York at Albany, Albany, New York 12222 (United States)

    2013-12-21

    Electroluminescence (EL) and electron emission into vacuum (EM) occur when a non-destructive dielectric breakdown of Al-Al{sub 2}O{sub 3}-Ag diodes, electroforming, results in the development of a filamentary region in which current-voltage (I-V) characteristics exhibit voltage-controlled negative resistance. The temperature dependence of I-V curves, EM, and, particularly, EL of Al-Al{sub 2}O{sub 3}-Ag diodes with anodic Al{sub 2}O{sub 3} thicknesses between 12 nm and 30 nm, has been studied. Two filters, a long-pass (LP) filter with transmission of photons with energies less than 3.0 eV and a short-pass (SP) filter with photon transmission between 3.0 and 4.0 eV, have been used to characterize EL. The voltage threshold for EL with the LP filter, V{sub LP}, is ∼1.5 V. V{sub LP} is nearly independent of Al{sub 2}O{sub 3} thickness and of temperature and is 0.3–0.6 V less than the threshold voltage for EL for the SP filter, V{sub SP}. EL intensity is primarily between 1.8 and 3.0 eV when the bias voltage, V{sub S} ≲ 7 V. EL in the thinnest diodes is enhanced compared to EL in thicker diodes. For increasing V{sub S}, for diodes with the smallest Al{sub 2}O{sub 3} thicknesses, there is a maximum EL intensity, L{sub MX}, at a voltage, V{sub LMX}, followed by a decrease to a plateau. L{sub MX} and EL intensity at 4.0 V in the plateau region depend exponentially on Al{sub 2}O{sub 3} thickness. The ratio of L{sub MX} at 295 K for a diode with 12 nm of Al{sub 2}O{sub 3} to L{sub MX} for a diode with 25 nm of Al{sub 2}O{sub 3} is ∼140. The ratio of EL intensity with the LP filter to EL intensity with the SP filter, LP/SP, varies between ∼3 and ∼35; it depends on Al{sub 2}O{sub 3} thickness and V{sub S}. Enhanced EL is attributed to the increase of the spontaneous emission rate of a dipole in a non-resonant optical microcavity. EL photons interact with the Ag and Al films to create surface plasmon polaritons (SPPs) at the metal-Al{sub 2}O

  11. Microstructure and Properties of Fe3Al-Fe3AlC x Composite Prepared by Reactive Liquid Processing

    Science.gov (United States)

    Verona, Maria Nalu; Setti, Dalmarino; Paredes, Ramón Sigifredo Cortés

    2018-04-01

    A Fe3Al-Fe3AlC x composite was prepared using reactive liquid processing (RLP) through controlled mixture of carbon steel and aluminum in the liquid state. The microstructure and phases of the composite were assessed using X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, optical microscopy, and differential scanning calorimetry. In addition, the density, hardness, microhardness, and elastic modulus were evaluated. The Fe3Al-Fe3AlC x composite consisted of 65 vol pct Fe3Al and 35 vol pct Fe3AlC x ( κ). The κ phase contained 10.62 at. pct C, resulting in the stoichiometry Fe3AlC0.475. The elastic modulus of the Fe3Al-Fe3AlC0.475 composite followed the rule of mixtures. The RLP technique was shown to be capable of producing Fe3Al-Fe3AlC0.475 with a microstructure and properties similar to those achieved using other processing techniques reported in the literature.

  12. Appiah-Adjei et al

    African Journals Online (AJOL)

    PUBLICATIONS1

    ing, sale of automobile spare parts, and metal fabrication. Some of these activities generate huge ... Keywords: Groundwater quality, pollution, waste disposal, Suame, Ghana ... of fertilizers (Chen et al., 2007; Parris, 2011;. Shen et al., 2011), ...

  13. KONSEP MᾹQᾹṢID AL-SYᾹRĪAH MENURUT ṬᾹHᾹ JᾹBIR AL-‘ALWᾹNĪ

    Directory of Open Access Journals (Sweden)

    Chasnak Najidah

    2017-03-01

    Full Text Available One discourse which is receiving considerable attention from scholars of Islam is about the objectives of Islamic law (maqasid al-shari'ah. Taha Jabir al-'Alwānī as one reviewer of Maqasid al-shari'ah contemporary formulate the concept of maqasid al-shari'ah different from previous scholars. This article describes the concept of maqasid al-shari'ah by Taha Jabir al-'Alwānī. According to him, there are three levels of hierarchical of Maqasid al-Sharia. The highest value of maqasid al-shari'ah says is what he describes as al-Maqasid al-'ulyā al-Hakimah (intentions of the highest shari'ah and a legal basis, which consists of three main elements, namely al-Tawhid ( Onesess of God, al-Tazkiyah (purification and al-'umrān (prosperity. The position of the second al-shari'ah Maqasid are universal values such as justice, freedom, and equality. While the third position is the formulation of the previous scholars regarding maqasid al-shari'ah consisting of ḍarūriyyat, ḥājiyyāt, and taḥsīniyyāt. In terms of methodological, Taha Jabir al-'Alwānī basing the new system for Maqasid al-syarī'ahnya on the methods of al-jam'u Baina al-qirā'atain, a reading of the two entities: the revelation of God and the universe. With this basis, he argues that the maqasid al-shari'ah formulations are qaṭ'ī, so it can be a reference to the scholars in solving the problems of contemporary law.   [Salah satu diskursus yang mendapat perhatian cukup besar dari para akademisi Islam adalah seputar tujuan-tujuan hukum islam  (maqāṣid al-syarī'ah. Ṭāhā Jābir al-‘Alwānī sebagai salah satu ulama pengkaji maqāṣid asy-syarī’ahkontemporer merumuskan konsep maqāṣid asy-syarī’ahyang berbeda dari ulama sebelumnya. Artikel ini mendeskripsikan konsep maqāṣid asy-syarī’ahmenurut Ṭāhā Jābir al-‘Alwānī. Menurutnya, ada tiga tingkatan hierarkis maqāṣid al-syarī'ah. Nilai tertinggi maqāṣid asy-syarī’ahmenurutnya adalah apa

  14. Measurement of the d({sup 26}Al{sup m},p){sup 27}Al reaction for nuclear astrophysics

    Energy Technology Data Exchange (ETDEWEB)

    Roeder, B.T.; Trache, L.; Iacob, V.E.; McCleskey, M.; Simmons, E.; Spiridon, A.; Tribble, R.E. [Texas A and M Univ., TX (United States); Davinson, T.; Lotay, G.; Woods, P.J. [University of Edinburgh (United Kingdom); La Cognata, M.; Pizzone, R.G.; Rapisarda, G.G.; Sparta, R.; Spitaleri, C. [Istituto Nazionale di Fisica Nucleare (LNS/INFN), Catania (Italy). Lab. Nazionali del Sud

    2012-07-01

    Full text: The detection of gamma rays from the decay of the {sup 26}Al ground state in the galaxy gives evidence that nucleosynthesis is occurring in present-day stars, but its origin is not yet clear. This implies that reactions involving {sup 26}Al are important for astrophysical processes. In a recent experiment at the Cyclotron Institute at Texas A and M University, reactions with the ground state and isomeric state of {sup 26}Al were investigated with the Texas A and M-Edinburgh-Catania Silicon detector Array (TECSA). TECSA is a collaborative effort to build a high-efficiency detector Si array useful for measuring reactions of interest for nuclear astrophysics and nuclear structure. The array consists of up to 16 Micron Semiconductor YY1 detectors that are each 300 μm thick. Each detector has 16 annular ring sectors to measure the energy and the scattering angle of the detected particles. Using TECSA, we measured d({sup 26}Al{sup g},p){sup 27}Al and d({sup 26}Al{sup m},p){sup 27}Al with a {sup 26}Al secondary beam prepared in-flight with the MARS spectrometer. First, the composition of the {sup 26}Al beam was determined by measuring the ratio of beta-decays to {sup 26}Al ions produced. It was found that at different spectrometer rigidities, beams of 2/3 isomer to ground state ratio or vice-versa could be obtained. Then, in the second part of the experiment, angular distributions were measured for both reactions at backward angles with TECSA. The protons were measured in TECSA in coincidence with timing signals from the beam detected by a scintillator and with the cyclotron radio-frequency. Details of the experiment and preliminary results from the analysis of the d({sup 26}Al{sup m},p){sup 27}Al and d({sup 26}Al{sup g},p){sup 27}Al data will be presented. They will give information about the proton capture reactions {sup 26}Al{sup m}(p,γ){sup 27}Si and {sup 26}Al{sup g}(p,γ){sup 27}Si taking place in stars. (author)

  15. Khajeh Nasir al-Din al-Tusi’s Role in the Interaction of Triple Paradigms of Islamic Philosophy

    Directory of Open Access Journals (Sweden)

    r Mohammadzadeh

    2013-09-01

    Full Text Available Our aim in this article is to investigate Khajeh Nasir`s effective role in emergence, growth and development of triple paradigms of Islamic philosophy, that are, Masha’, Ishraq and al-Hekmah al-Motealiyeh. Thus, first we present a summary of the meaning of “paradigm” and then discuss Tusi`s role in the development of triple paradigms of Islamic philosophy. We believe that, by using an interactive approach, Khajeh Nasir has attained a new approach to understand the paradigms. He is the first thinker in Islamic world who created a constructive and effective interaction between two paradigms of Masha’ and Ishraq, and paved the way for the emergence of al-Hekmah al-Motealiyeh. This can be explained with regard to either the conceptualization of al-Hekmat al-Motealiyeh or epistemological approach. Al-Hekmah Al-Motealiyah was influenced a lot by Tusi.

  16. Characterization of microstructure and mechanical properties of friction stir welded AlMg5- Al_2O_3 nanocomposites

    International Nuclear Information System (INIS)

    Babu, N. Kishore; Kallip, Kaspar; Leparoux, Marc; AlOgab, Khaled A.; Reddy, G.M.; Talari, M.K.

    2016-01-01

    In the present study, powder metallurgy processed unmilled AlMg5, milled AlMg5 and milled AlMg5-0.5 vol% Al_2O_3 nanocomposite have been successfully friction stir welded (FSW). The effect of friction stir welding on the evolution of weld microstructures; hardness and tensile properties were studied and discussed in detail. FSW of unmilled AlMg5 resulted in significant grain refinement and strain hardening in the nugget zone induced by the thermo-mechanical processing, thereby increasing the stir zone hardness and tensile strengths to 100 HV and 324 MPa when compared to 80 HV and 300 MPa of base metal, respectively. In contrast, the FSW of milled AlMg5 and milled AlMg5-0.5 vol% Al_2O_3 samples showed a reduction in UTS values to 375 MPa and 401 MPa in the stir zone compared to 401 MPa and 483 MPa of respective base metal values. Transmission electron microscopic (TEM) investigation of weld stir zones revealed the homogenous distribution of Al_4C_3 nanophases in milled AlMg5 and Al_2O_3 nanoparticles in milled AlMg5-0.5 vol% Al_2O_3 samples throughout the aluminium matrix. It was revealed that the pre-stored energy from the prior ball milling and hot pressing processes, higher deformation energy and grain boundary pinning effect due to the presence of reinforcement particles has resulted in a higher recrystallization tendency and retarded grain growth during FSW of milled samples. The welds prepared with milled AlMg5-0.5 vol% Al_2O_3 exhibited higher hardness and tensile strength in the stir zone when compared to all other conditions which was attributed to Hall Petch effect due to fine grain size and Orowan strengthening effect due to Al_2O_3 reinforcements.

  17. Experimental investigation of the Al-Y phase diagram

    International Nuclear Information System (INIS)

    Liu Shuhong; Du Yong; Xu Honghui; He Cuiyun; Schuster, Julius C.

    2006-01-01

    The Al-Y phase diagram has been reinvestigated with 16 key alloys over its whole composition range by means of differential thermal analysis, X-ray diffraction, optical microscopy, and scanning electron microscopy with energy dispersive X-ray techniques. The existence of five intermetallic phases, Al 3 Y, Al 2 Y, AlY, Al 2 Y 3 , and AlY 2 , has been confirmed. Al 2 Y and Al 2 Y 3 melt congruently at 1490 ± 2 and 1105 ± 2 deg. C, respectively. Al 3 Y, AlY, and AlY 2 are formed via the peritectic reactions L + Al 2 Y ↔ Al 3 Y at 980 ± 2 deg. C, L + Al 2 Y ↔ AlY at 1138 ± 2 deg. C, and L + Al 2 Y 3 ↔ AlY 2 at 977 ± 2 deg. C, respectively. Three eutectic reactions L ↔ (Al) + Al 3 Y at 637 ± 2 deg. C, L ↔ AlY + Al 2 Y 3 at 1081 ± 2 deg. C, and L ↔ AlY 2 + (αY) at 955 ± 2 deg. C , are observed. The previously reported Al 3 Y 5 , AlY 3 compounds were not found. A revised Al-Y phase diagram is presented mainly based on the present experimental results

  18. The corrosion and mechanical behaviour of Al, FeCrAlY, and CoCrAlY coatings in aggressive environments

    NARCIS (Netherlands)

    Haanappel, V.A.C.; Haanappel, V.A.C.; Geerdink, Bert; Fransen, T.; Gellings, P.J.

    1991-01-01

    The mechanical and chemical behaviours of aluminide coatings applied by pack cementation, FeCrAlY coatings applied by plasma spraying and CoCrAlY coatings applied by electrodeposition were studied. The coatings were pretreated for 0.5 h in argon at 1373 K to improve the adhesion and structural

  19. Precipitation and strengthening phenomena in Al-Si-Ge and Al-Cu-Si-Ge alloys

    International Nuclear Information System (INIS)

    Mitlin, D.; Morris, J.W.; Dahmen, U.; Radmilovic, V.

    2000-01-01

    The objective of this work was to determine whether Al rich Al-Si-Ge and 2000 type Al-Cu-Si-Ge alloys have sufficient hardness to be useful for structural applications. It is shown that in Al-Si-Ge it is not possible to achieve satisfactory hardness through a conventional heat treatment. This result is explained in terms of sluggish precipitation of the diamond-cubic Si-Ge phase coupled with particle coarsening. However, Al-Cu-Si-Ge displayed a uniquely fast aging response, a high peak hardness and a good stability during prolonged aging. The high hardness of the Cu containing alloy is due to the dense and uniform distribution of fine θ' precipitates (metastable Al 2 Cu) which are heterogeneously nucleated on the Si-Ge particles. High resolution TEM demonstrated that in both alloys all the Si-Ge precipitates start out, and remain multiply twinned throughout the aging treatment. Since the twinned section of the precipitate does not maintain a low index interface with the matrix, the Si-Ge precipitates are equiaxed in morphology. Copyright (2000) AD-TECH - International Foundation for the Advancement of Technology Ltd

  20. Bankole et al (2)

    African Journals Online (AJOL)

    DELL

    Relationships of Clay-filled Channels on the Delta Flanks (Modified after Doust and Omatsola, 1990 and Lawrence et al., 2002). ... and in the Indo-Malaysian area (Germeraad et al.,. 1968). The genus ..... Upper Cretaceous of British Guiana.

  1. Aussprache als motorische Fertigkeit

    DEFF Research Database (Denmark)

    Bonner, Maria

    2013-01-01

    Authentische Aussprache gilt im Fremdsprachenunterricht als schwer erreichbares Ziel, fremdsprachlicher Akzent wird als nahezu unvermeidbar gesehen. Weder die Hypothese einer kritischen Periode für den Erwerb einer authentischen Aussprache noch das Konzept der Fossilierung im Sprachlernprozess...

  2. The removal of bisphenol A from aqueous solutions by MIL-53(Al) and mesostructured MIL-53(Al).

    Science.gov (United States)

    Zhou, Meimei; Wu, Yi-Nan; Qiao, Junlian; Zhang, Jing; McDonald, Amanda; Li, Guangtao; Li, Fengting

    2013-09-01

    In this work, metal-organic framework MIL-53(Al){Al(OH)[O2C-C6H4-CO2]} and MIL-53(Al)-F127{Al(OH)[O2C-C6H4-CO2]} were synthesized and used as sorbents to remove bisphenol A (BPA) from aqueous system. The sorption kinetics data of BPA were found to be in agreement with the pseudo-second-order model. The equilibrium sorption amounts of BPA on MIL-53(Al) and MIL-53(Al)-F127 reached 329.2±16.5 and 472.7±23.6 mg g(-1), respectively, far more than that of commercial activated carbons (ranging from 129.6 to 263.1 mg g(-1)). Both MIL-53(Al) and MIL-53(Al)-F127 could remove BPA fast from aqueous solutions, and the required contact time to reach equilibrium was approximately 90 min for MIL-53(Al) and 30 min for MIL-53(Al)-F127, respectively. The optimum pH levels for the removal of BPA using MIL-53 (Al) and MIL-53(Al)-F127 were 4 and 6 separately. The optimum temperature for the sorption behavior of BPA on the two sorbents was 20 °C. The results performed show that the resulting products, as one kind of MOFs, can be regarded as a new class of sorbents for water treatment and could find great applications in the fields of environmental water pollution control and resources reuse. Copyright © 2013 Elsevier Inc. All rights reserved.

  3. Hyperfine fields and spin relaxation of Ce in GdAl2 and DyAl2

    International Nuclear Information System (INIS)

    Waeckelgaard, E.; Karlsson, E.; Lindgren, B.; Mayer, A.

    1987-04-01

    We have investigated the ferromagnetic state of the cubic intermetallic compounds GdAl 2 and DyAl 2 with the 140 Ce nuclei using DPAC. The local fields of Ce are for the lowest measured temperatures B eff (30 K) = 54(2) T for GdAl 2 and B eff (12.5 K) = 27(1) T for DyAl 2 which are considerably lower than the hyperfine field measured for a free Ce ion (183 T). By introducing a crystal field, of cubic symmetry, a lower hyperfine field is obtained which is in quantitative agreement with the local field of Ce in GdAl 2 . For DyAl 2 an additional effect, represented by a non-magnetic level below the lowest magnetic level, may explain a further reduction of the hyperfine field. Two models relating to a Kondo non-magnetic state of Ce are discussed. Spin relaxation in the paramagnetic state are also studied and compared with observations of the same systems measured with μSR. (authors)

  4. Experimental evidence of structural transition at the crystal-amorphous interphase boundary between Al and Al2O3

    International Nuclear Information System (INIS)

    Yang, Z.Q.; He, L.L.; Zhao, S.J.; Ye, H.Q.

    2002-01-01

    High-resolution transmission electron microscopy observations on the structure of the interphase boundary between crystalline Al and amorphous Al 2 O 3 coating reveal that an interfacial melting transition of Al occurs at 833 K, which is distinctly lower than the bulk melting point of Al. The crystalline lattice planes of Al near the interface bend or small segments of crystalline Al deviated from the matrix Al grains are formed. Stand-off dislocations formed at the interphase boundary are also observed. The amorphous Al 2 O 3 coating plays an important role in retaining the evidence for structural transition at high temperature to room temperature, which makes it possible to make experimental observations. (author)

  5. Room-Temperature Quantum Ballistic Transport in Monolithic Ultrascaled Al-Ge-Al Nanowire Heterostructures.

    Science.gov (United States)

    Sistani, Masiar; Staudinger, Philipp; Greil, Johannes; Holzbauer, Martin; Detz, Hermann; Bertagnolli, Emmerich; Lugstein, Alois

    2017-08-09

    Conductance quantization at room temperature is a key requirement for the utilizing of ballistic transport for, e.g., high-performance, low-power dissipating transistors operating at the upper limit of "on"-state conductance or multivalued logic gates. So far, studying conductance quantization has been restricted to high-mobility materials at ultralow temperatures and requires sophisticated nanostructure formation techniques and precise lithography for contact formation. Utilizing a thermally induced exchange reaction between single-crystalline Ge nanowires and Al pads, we achieved monolithic Al-Ge-Al NW heterostructures with ultrasmall Ge segments contacted by self-aligned quasi one-dimensional crystalline Al leads. By integration in electrostatically modulated back-gated field-effect transistors, we demonstrate the first experimental observation of room temperature quantum ballistic transport in Ge, favorable for integration in complementary metal-oxide-semiconductor platform technology.

  6. The effectiveness of ERC advanced life support (ALS) provider courses for the retention of ALS knowledge.

    Science.gov (United States)

    Fischer, Henrik; Strunk, Guido; Neuhold, Stephanie; Kiblböck, Daniel; Trimmel, Helmut; Baubin, Michael; Domanovits, Hans; Maurer, Claudia; Greif, Robert

    2012-02-01

    Out-of-hospital emergency physicians in Austria need mandatory emergency physician training, followed by biennial refresher courses. Currently, both standardized ERC advanced life support (ALS) provider courses and conventional refresher courses are offered. This study aimed to compare the retention of ALS-knowledge of out-of-hospital emergency physicians depending on whether they had or had not participated in an ERC-ALS provider course since 2005. Participants (n=807) from 19 refresher courses for out-of-hospital emergency physicians answered eight multiple-choice questions (MCQ) about ALS based on the 2005 ERC guidelines. The pass score was 75% correct answers. A multivariate logistic regression analyzed differences in passing scores between those who had previously participated in an ERC-ALS provider course and those who had not. Age, gender, regularity of working as an out-of-hospital emergency physician and the self-reported number of real resuscitation efforts within the last 6months were entered as control variables. Out-of-hospital emergency physicians who had previously attended an ERC-ALS provider course had a significantly higher chance of passing the MCQ test (OR=1.60, p=0.015). Younger age (OR=0.95, pERC-ALS provider course since 2005 had a higher retention of ALS knowledge compared to non-ERC-ALS course participants. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  7. X-ray study of rapidly cooled ribbons of Al-Cr-Zr and Al-Ni-Y-Cr-Zr alloys

    International Nuclear Information System (INIS)

    Betsofen, S.Ya.; Osintsev, O.E.; Lutsenko, A.N.; Konkevich, V.Yu.

    2002-01-01

    One investigated into phase composition, lattice spacing and structure of rapidly cooled 25-200 μm gauge strips made of Al-4,1Cr-3,2Zr and Al-1,5Cr-1,5Zr-4Ni-3Y alloys, wt. %, produced by melt spinning to a water-cooled copper disk. In Al-4,1Cr-3,2Zr alloy one detected intermetallic phases: Al 3 Zr and two Al 86 Cr 14 composition icosahedral phases apart from aluminium solid solution with 4.040-4.043 A lattice spacing. In Al-1,5Cr-1,5Zr-4Ni-3Y alloy one identified two Al 86 Cr 14 icosahedral phases and two AlNiY and Al 3 Y yttrium-containing ones, lattice spacing of aluminium solid solution was equal to 4.052-4.053 A [ru

  8. The Influence of the Asymmetric Arb Process on the Properties of Al-Mg-Al Multi-Layer Sheets / Wpływ Asymetrii W Procesie Arb Na Właściwości Wielowarstwowych Blach Al-Mg-Al

    Directory of Open Access Journals (Sweden)

    Wierzba A.

    2015-12-01

    Full Text Available The paper presents the results of the experimental study of the three-layer Al-Mg-Al sheets rolling process by the ARB method. The tests carried out were limited to single-pass symmetric and asymmetric rolling processes. An Al-Mg-Al package with an initial thickness of 4 mm (1-2-1 mm was subjected to the process of rolling with a relative reduction of 50%. To activate the shear band in the strip being deformed, an asymmetry factor of av=2 was applied. From the test results, an increase in the tensile strength of the multi-layer Al-Mg-Al sheets obtained from the asymmetric process was observed. Microhardness tests did not show any significant differences in aluminium layer between respective layers of sheets obtained from the symmetric and the asymmetric process. By contrast, for the magnesium layer, an increase in microhardness from 72 HV to 79 HV could be observed for the asymmetric rolling. The analysis of the produced Al-Mg-Al sheets shows that the good bond between individual layers and grain refinement in the magnesium layer contributed to the obtaining of higher mechanical properties in the multi-layer sheets produced in the asymmetric process compared to the sheets obtained from the symmetric process.

  9. The investigation of Al0.29Ga0.71N/GaN/AlN and AlN/GaN/AlN thin films grown on Si (111) by RF plasma-assisted MBE

    Science.gov (United States)

    Yusoff, Mohd Zaki Mohd; Mahyuddin, Azzafeerah; Hassan, Zainuriah; Hassan, Haslan Abu; Abdullah, Mat Johar

    2012-06-01

    Recently, gallium nitride (GaN) and its related compounds involving Al and In have attracted much attention because of their potential to be used as high-efficiency UV light emitting devices, and as high frequency and high power electronic devices. Consequently, the growth and physics of GaN-based materials have attracted remarkable scientific attention. In this work, the growth and characterization of epitaxial Al0.29Ga0.71N and AlN layers grown on Si (111) by RF-plasma assisted molecular beam epitaxy (MBE) are described. The Al mole fraction was derived from the HR-XRD symmetric rocking curve (RC) ω/2θ scans of (0002) plane as x = 0.29. For AlN/GaN/AlN sample, the maximum Raman intensity at 521.53 cm-1 is attributed to crystalline silicon. It was found that the allowed Raman optical phonon mode of GaN, the E1 (high) is clearly visible, which is located at 570.74 cm-1. Photoluminscence (PL) spectrums of both samples have shown sharp and intense band edge emission of GaN without the existence of yellow emission band, showing good crystal quality of the samples have been successfully grown on Si substrate.

  10. Field ion microscopy and 3-D atom probe analysis of Al3Zr particles in 7050 Al alloy

    International Nuclear Information System (INIS)

    Sha, G.; Cerezo, A.

    2004-01-01

    Full text: For high strength 7xxx series Al alloys, Zr is an important trace alloy element which is often added to optimise properties, having effects such as refining grain size, inhibiting recrystallization, and improving stress corrosion cracking resistance and quench sensitivity. In addition, it has been reported recently that Zr addition also has a significant influence on early stage ageing behaviour of a 7xxx series Al alloy. Zr equilibrium solubility in solid Al is extremely low. After solution or ageing treatment, most Zr is present as small spherical Ai 3 Zr dispersoids approximately 20 nm in diameter, distributed at grain boundaries as well as within the Al matrix. The crystallographic nature of intermetallic phase Al 3 Zr has been well studied in the literatures. So far, no direct measurement of the chemistry of the Al 3 Zr particles in 7xxx series Al alloys has been published. It is unclear if there is significant Zn, Mg or Cu included in the particles. In this research, 3DAP has been employed for the first time to investigate ionisation behaviour of Al 3 Zr particles and determine the chemistry of the particles in 7050 Al alloy. Using field ion microscopy, the local evaporation radius of the Al 3 Zr particle has been measured to be equivalent to 36 nm for a 10 kV tip, less than the equivalent tip radius for the Al matrix of ∼68 nm. Using the matrix Al evaporation field (19 V/nm) as a reference, this allows the evaporation field of Al 3 Zr to be calculated as 35 V/nm, the same as the field calculated for evaporation of Al as Al 2+ (35 V/nm), and that of Zr as Zr 3+ (35 V/nm). This result is consistent with Al 2+ and Zr 3+ being the main species observed in the mass spectrum during analysis of Al 3 Zr particles. Using 3DAP, the chemical compositions of Al 3 Zr particles are determined to be 64.8∼67.7 at% Al, 23.6∼24.8 at% Zr, 6.9∼9.1 at% Zn, 0.4∼0.7 at% Cu, 0.5∼1.2 at% Mg, with a (Al+Zn)/Zr ratio close to 3. Choice of specimen temperature of

  11. Synthesis and structural transformations of hydrotalcite-like materials Mg-Al and Zn-Al

    NARCIS (Netherlands)

    Prihod'ko, R.V.; Sychev, M.V.; Astrelin, I.M.; Erdmann, K.; Mangel, A.; Santen, van R.A.

    2001-01-01

    Mg-Al and Zn-Al hydrotalcite-like layered double hydroxides of various compositions were synthesized and characterized. A detailed comparative analysis of the structure and composition of starting and reconstructed layered double hydroxides was made

  12. Natural radioactivity survey in Al-Jabal Al-Gharbi Mountain Region Libya

    International Nuclear Information System (INIS)

    Askouri, N.A.; Hussain, M.O.; Al-Ojaily, A.S.

    2011-01-01

    The measurement of natural radioactivity in a given region or country is essential to provide a reference base-line map to follow up a possible variation in future. In order to perform such measurement, the natural radioactivity was measured in different locations. The locations (50 sites) were distributed over Al-Jabal Al-Gharbi Mountain, starting from the city Al-Azeeziah in the eastern part to Wazen on the Tunisian border in the west. The measurements showed obvious variation from one site to another. The levels were fluctuating from (12.8 counts/minute) in Bir-Ayad to (45.7 counts/minute) in Gherian. In order to investigate the cause for such variation, samples were collected from (27) sites for detailed study. The levels of natural radioactivity were determined in the laboratory, and were ranging from (58.7 Bq/kg) in Bir-Ayad to (102.1 Bq/kg) in Gherian. The variation in measured radioactivity was related to the geological structures taken in six perpendicular sections, namely, Gharian, Yevren, Zintan, Nalut, Wazen and Al-Azeeziah taking the naturally occurred radioisotopes concentration of 4 0K, 232 Th and 238 U present in consideration.

  13. Digitalisierung und Selbstbestimmung

    Directory of Open Access Journals (Sweden)

    Bezemek, Christoph

    2017-12-01

    Full Text Available Der vorliegende Beitrag skizziert das Zusammenspiel von Digitalisierung und individueller Selbstbestimmung, stellt die Frage, welche Herausforderungen dieses Zusammenspiel birgt und diskutiert, wie ihnen begegnet werden kann.

  14. Phase constituents and microstructure of laser cladding Al2O3/Ti3Al reinforced ceramic layer on titanium alloy

    International Nuclear Information System (INIS)

    Li Jianing; Chen Chuanzhong; Lin Zhaoqing; Squartini, Tiziano

    2011-01-01

    Research highlights: → In this study, Fe 3 Al has been chosen as cladding powder due to its excellent properties of wear resistance and high strength, etc. → Laser cladding of Fe 3 Al + TiB 2 /Al 2 O 3 pre-placed alloy powder on Ti-6Al-4V alloy substrate can form the Ti 3 Al/Fe 3 Al + TiB 2 /Al 2 O 3 ceramic layer, which can increase wear resistance of substrate. → In cladding process, Al 2 O 3 can react with TiB 2 leading to formation of Ti 3 Al and B. → This principle can be used to improve the Fe 3 Al + TiB 2 laser-cladded coating. - Abstract: Laser cladding of the Fe 3 Al + TiB 2 /Al 2 O 3 pre-placed alloy powder on Ti-6Al-4V alloy can form the Ti 3 Al/Fe 3 Al + TiB 2 /Al 2 O 3 ceramic layer, which can greatly increase wear resistance of titanium alloy. In this study, the Ti 3 Al/Fe 3 Al + TiB 2 /Al 2 O 3 ceramic layer has been researched by means of electron probe, X-ray diffraction, scanning electron microscope and micro-analyzer. In cladding process, Al 2 O 3 can react with TiB 2 leading to formation of amount of Ti 3 Al and B. This principle can be used to improve the Fe 3 Al + TiB 2 laser cladded coating, it was found that with addition of Al 2 O 3 , the microstructure performance and micro-hardness of the coating was obviously improved due to the action of the Al-Ti-B system and hard phases.

  15. Precipitation in cold-rolled Al-Sc-Zr and Al-Mn-Sc-Zr alloys prepared by powder metallurgy

    KAUST Repository

    Vlach, Martin

    2013-12-01

    The effects of cold-rolling on thermal, mechanical and electrical properties, microstructure and recrystallization behaviour of the AlScZr and AlMnScZr alloys prepared by powder metallurgy were studied. The powder was produced by atomising in argon with 1% oxygen and then consolidated by hot extrusion at 350 C. The electrical resistometry and microhardness together with differential scanning calorimetry measurements were compared with microstructure development observed by transmission and scanning electron microscopy, X-ray diffraction and electron backscatter diffraction. Fine (sub)grain structure developed and fine coherent Al3Sc and/or Al3(Sc,Zr) particles precipitated during extrusion at 350 C in the alloys studied. Additional precipitation of the Al3Sc and/or Al3(Sc,Zr) particles and/or their coarsening was slightly facilitated by the previous cold rolling. The presence of Sc,Zr-containing particles has a significant antirecrystallization effect that prevents recrystallization at temperatures minimally up to 420 C. The precipitation of the Al6Mn- and/or Al 6(Mn,Fe) particles of a size ~ 1.0 μm at subgrain boundaries has also an essential antirecrystallization effect and totally suppresses recrystallization during 32 h long annealing at 550 C. The texture development of the alloys seems to be affected by high solid solution strengthening by Mn. The precipitation of the Mn-containing alloy is highly enhanced by a cold rolling. The apparent activation energy of the Al3Sc particles formation and/or coarsening and that of the Al6Mn and/or Al 6(Mn,Fe) particle precipitation in the powder and in the compacted alloys were determined. The cold deformation has no effect on the apparent activation energy values of the Al3Sc-phase and the Al 6Mn-phase precipitation. © 2013 Elsevier Inc.

  16. Precipitation in cold-rolled Al-Sc-Zr and Al-Mn-Sc-Zr alloys prepared by powder metallurgy

    KAUST Repository

    Vlach, Martin; Stulí ková , Ivana; Smola, Bohumil; Kekule, Tomá š; Kudrnová , Hana; Daniš, Stanislav; Gemma, Ryota; Očená šek, Vladivoj; Má lek, Jaroslav; Tanprayoon, Dhritti; Neubert, Volkmar

    2013-01-01

    The effects of cold-rolling on thermal, mechanical and electrical properties, microstructure and recrystallization behaviour of the AlScZr and AlMnScZr alloys prepared by powder metallurgy were studied. The powder was produced by atomising in argon with 1% oxygen and then consolidated by hot extrusion at 350 C. The electrical resistometry and microhardness together with differential scanning calorimetry measurements were compared with microstructure development observed by transmission and scanning electron microscopy, X-ray diffraction and electron backscatter diffraction. Fine (sub)grain structure developed and fine coherent Al3Sc and/or Al3(Sc,Zr) particles precipitated during extrusion at 350 C in the alloys studied. Additional precipitation of the Al3Sc and/or Al3(Sc,Zr) particles and/or their coarsening was slightly facilitated by the previous cold rolling. The presence of Sc,Zr-containing particles has a significant antirecrystallization effect that prevents recrystallization at temperatures minimally up to 420 C. The precipitation of the Al6Mn- and/or Al 6(Mn,Fe) particles of a size ~ 1.0 μm at subgrain boundaries has also an essential antirecrystallization effect and totally suppresses recrystallization during 32 h long annealing at 550 C. The texture development of the alloys seems to be affected by high solid solution strengthening by Mn. The precipitation of the Mn-containing alloy is highly enhanced by a cold rolling. The apparent activation energy of the Al3Sc particles formation and/or coarsening and that of the Al6Mn and/or Al 6(Mn,Fe) particle precipitation in the powder and in the compacted alloys were determined. The cold deformation has no effect on the apparent activation energy values of the Al3Sc-phase and the Al 6Mn-phase precipitation. © 2013 Elsevier Inc.

  17. Editorial: Partizipationschancen im Kulturraum Internet nutzen und gestalten: Das Beispiel Web 2.0

    Directory of Open Access Journals (Sweden)

    Kerstin Mayrberger

    2011-10-01

    Web 2.0» auf dem Kongress «Bildung in der Demokratie» der Deutschen Gesellschaft der Erziehungswissenschaft (DGfE im März 2010 in Mainz gehalten wurden. Hans Geser diskutiert in seinem Beitrag «Kakophonie und Selbstorganisation in der digitialen Agora» kritisch die Ausweitung niederschwelliger, öffentlicher Partizipationschancen. Dabei unterstreicht er die Bedeutsamkeit informeller politischer Bildungsprozesse, die ein digitales, politisches Engagement mit sich bringt bzw. bringen kann und deren Potenzial als Übungsfeld. Er führt erste Rahmenbedingungen und Basismerkmale einer «neuen politischen Öffentlichkeit» aus und geht auf die Folgen der Loskoppelung politischer Kommunikation vom politischen Handeln ein. Heinz Moser befasst sich in seinem Beitrag «Das politische Internet – Möglichkeiten und Grenzen» mit der Frage, inwieweit sich die Qualität und Kultur der Bürgerpartizipation durch die junge Generation und ihre Mediennutzungsvorlieben verändert. Nach Ausführungen zu Formen von eGouvernment, eParticipation und eVoting mit Bezug zu bestehenden sozialwissenschaftlichen Ansätzen im Kontext von eDemokratie folgt die Zusammenfassung einer empirischen Untersuchung von politischer Partizipation am Beispiel von politischen Gruppen aus der Schweiz, die sich auf Facebook gebildet haben. Heike Schaumburg stellt in ihrem Beitrag «Politische Bildung und das Web 2.0» eine empirische Studie vor, die der Frage nachgeht, inwieweit das Web 2.0 in der Lage ist, die in die Social Software gesetzten Hoffnungen nach mehr Partizipation, Kommunikation und Vernetzung für die politische Bildung zu erfüllen. Der Beitrag erörtert, welche Potenziale das Web 2.0 für die Politische Bildung mit Blick auf ihre didaktische Gestaltung bietet, bevor er auf Basis einer Analyse bildungspolitischer Internet-Angebote Aussagen über die gegenwärtige Verbreitung von Web 2.0 Angeboten in der Politischen Bildung trifft. Schliesslich wird auf der Grundlage einer Nutzerbefragung

  18. Universitat popular al Cabanyal

    OpenAIRE

    Ribés Granell, Juan Miguel

    2012-01-01

    La intención es dotar al barrio de un gran espacio verde y de un edificio de interés para los vecinos que enriquezca al Cabanyal, ya que actualmente se encuentra en proceso de degradación. Se pretende desarrollar un proyecto que signifique una mejora en la predisposición del visitante, cubriendo sus necesidades. Al mismo tiempo, se busca crear un espacio arquitectónico que mejore la relación entre las actividades que incluye y su entorno. El proyecto está condicionado por cuatro aspectos fund...

  19. Nonequilibrium synthesis of NbAl3 and Nb-Al-V alloys by laser cladding. II - Oxidation behavior

    Science.gov (United States)

    Haasch, R. T.; Tewari, S. K.; Sircar, S.; Loxton, C. M.; Mazumder, J.

    1992-01-01

    Isothermal oxidation behaviors of NbAl3 alloy synthesized by laser cladding were investigated at temperatures between 800 and 1400 C, and the effect of vanadium microalloying on the oxidation of the laser-clad alloy was examined. The oxidation kinetics of the two alloys were monitored using thermal gravimetric weight gain data, and the bulk and surface chemistries were analyzed using XRD and XPS, respectively. It was found that NbAl3 did not form an exclusive layer of protective Al2O3. The oxidation products at 800 C were found to be a mixture of Nb2O5 and Al2O3. At 1200 C, a mixture of NbAlO4, Nb2O5, and Al2O3 formed; and at 1400 C, a mixture of NbAlO4, Al2O3, NbO2, NbO(2.432), and Nb2O5 formed. The addition of V led to a dramatic increase of the oxidation rate, which may be related to the formation of (Nb, V)2O5 and VO2, which grows in preference to protective Al2O3.

  20. Completing the Heterocubane Family [Cp*AlE]4 (E = O, S, Se, and Te) by Selective Oxygenation and Sulfuration of [Cp*Al]4: Density Functional Theory Calculations of [Cp*AlE]4 and Reactivity of [Cp*AlO]4 toward Hydrolysis.

    Science.gov (United States)

    Stelzer, Adrian C; Hrobárik, Peter; Braun, Thomas; Kaupp, Martin; Braun-Cula, Beatrice

    2016-05-16

    The subvalent aluminum compound [Cp*Al]4 (1) reacts with dioxygen, N2O, or sulfur to yield the heterocubane complexes [Cp*AlX]4 [X = O (2) and S (3)]. Treatment of [Cp*AlO]4 (2) with (tBuO)3SiOH gave [(tBuO)3SiOAlO]4 (6) and Cp*H. The structures and spectroscopic data of the Al clusters are supported by density functional theory (DFT) calculations, which also demonstrate the importance of noncovalent interactions (NCI) in oligomeric Al(I) complexes as well as in [Cp*AlS]4 and the heavier homologues of Se and Te. The computed (27)Al NMR shifts indicate a deshielding at the Al centers with increasing electronegativity of the chalcogen atom as well as significant spin-orbit shielding effects within the heavier heterocubane [Al4E4] cores. Further hydrolysis of 6 with an additional amount of silanol in the presence of water resulted in the formation of [Al4(OH)6(OH2)2(OSiOtBu3)6] (7), which shows a structural motif found in boehmite and diaspore.