WorldWideScience

Sample records for absorption rates sars

  1. Combined acquisition technique (CAT for neuroimaging of multiple sclerosis at low specific absorption rates (SAR.

    Directory of Open Access Journals (Sweden)

    Armin Biller

    Full Text Available PURPOSE: To compare a novel combined acquisition technique (CAT of turbo-spin-echo (TSE and echo-planar-imaging (EPI with conventional TSE. CAT reduces the electromagnetic energy load transmitted for spin excitation. This radiofrequency (RF burden is limited by the specific absorption rate (SAR for patient safety. SAR limits restrict high-field MRI applications, in particular. MATERIAL AND METHODS: The study was approved by the local Medical Ethics Committee. Written informed consent was obtained from all participants. T2- and PD-weighted brain images of n = 40 Multiple Sclerosis (MS patients were acquired by CAT and TSE at 3 Tesla. Lesions were recorded by two blinded, board-certificated neuroradiologists. Diagnostic equivalence of CAT and TSE to detect MS lesions was evaluated along with their SAR, sound pressure level (SPL and sensations of acoustic noise, heating, vibration and peripheral nerve stimulation. RESULTS: Every MS lesion revealed on TSE was detected by CAT according to both raters (Cohen's kappa of within-rater/across-CAT/TSE lesion detection κCAT = 1.00, at an inter-rater lesion detection agreement of κLES = 0.82. CAT reduced the SAR burden significantly compared to TSE (p<0.001. Mean SAR differences between TSE and CAT were 29.0 (± 5.7 % for the T2-contrast and 32.7 (± 21.9 % for the PD-contrast (expressed as percentages of the effective SAR limit of 3.2 W/kg for head examinations. Average SPL of CAT was no louder than during TSE. Sensations of CAT- vs. TSE-induced heating, noise and scanning vibrations did not differ. CONCLUSION: T2-/PD-CAT is diagnostically equivalent to TSE for MS lesion detection yet substantially reduces the RF exposure. Such SAR reduction facilitates high-field MRI applications at 3 Tesla or above and corresponding protocol standardizations but CAT can also be used to scan faster, at higher resolution or with more slices. According to our data, CAT is no more uncomfortable than TSE scanning.

  2. Combined Acquisition Technique (CAT) for Neuroimaging of Multiple Sclerosis at Low Specific Absorption Rates (SAR)

    Science.gov (United States)

    Biller, Armin; Choli, Morwan; Blaimer, Martin; Breuer, Felix A.; Jakob, Peter M.; Bartsch, Andreas J.

    2014-01-01

    Purpose To compare a novel combined acquisition technique (CAT) of turbo-spin-echo (TSE) and echo-planar-imaging (EPI) with conventional TSE. CAT reduces the electromagnetic energy load transmitted for spin excitation. This radiofrequency (RF) burden is limited by the specific absorption rate (SAR) for patient safety. SAR limits restrict high-field MRI applications, in particular. Material and Methods The study was approved by the local Medical Ethics Committee. Written informed consent was obtained from all participants. T2- and PD-weighted brain images of n = 40 Multiple Sclerosis (MS) patients were acquired by CAT and TSE at 3 Tesla. Lesions were recorded by two blinded, board-certificated neuroradiologists. Diagnostic equivalence of CAT and TSE to detect MS lesions was evaluated along with their SAR, sound pressure level (SPL) and sensations of acoustic noise, heating, vibration and peripheral nerve stimulation. Results Every MS lesion revealed on TSE was detected by CAT according to both raters (Cohen’s kappa of within-rater/across-CAT/TSE lesion detection κCAT = 1.00, at an inter-rater lesion detection agreement of κLES = 0.82). CAT reduced the SAR burden significantly compared to TSE (pCAT were 29.0 (±5.7) % for the T2-contrast and 32.7 (±21.9) % for the PD-contrast (expressed as percentages of the effective SAR limit of 3.2 W/kg for head examinations). Average SPL of CAT was no louder than during TSE. Sensations of CAT- vs. TSE-induced heating, noise and scanning vibrations did not differ. Conclusion T2−/PD-CAT is diagnostically equivalent to TSE for MS lesion detection yet substantially reduces the RF exposure. Such SAR reduction facilitates high-field MRI applications at 3 Tesla or above and corresponding protocol standardizations but CAT can also be used to scan faster, at higher resolution or with more slices. According to our data, CAT is no more uncomfortable than TSE scanning. PMID:24608106

  3. Resonance behaviour of whole-body averaged specific energy absorption rate (SAR) in the female voxel model, NAOMI

    International Nuclear Information System (INIS)

    Dimbylow, Peter

    2005-01-01

    Finite-difference time-domain (FDTD) calculations have been performed of the whole-body averaged specific energy absorption rate (SAR) in a female voxel model, NAOMI, under isolated and grounded conditions from 10 MHz to 3 GHz. The 2 mm resolution voxel model, NAOMI, was scaled to a height of 1.63 m and a mass of 60 kg, the dimensions of the ICRP reference adult female. Comparison was made with SAR values from a reference male voxel model, NORMAN. A broad SAR resonance in the NAOMI values was found around 900 MHz and a resulting enhancement, up to 25%, over the values for the male voxel model, NORMAN. This latter result confirmed previously reported higher values in a female model. The effect of differences in anatomy was investigated by comparing values for 10-, 5- and 1-year-old phantoms rescaled to the ICRP reference values of height and mass which are the same for both sexes. The broad resonance in the NAOMI child values around 1 GHz is still a strong feature. A comparison has been made with ICNIRP guidelines. The ICNIRP occupational reference level provides a conservative estimate of the whole-body averaged SAR restriction. The linear scaling of the adult phantom using different factors in longitudinal and transverse directions, in order to match the ICRP stature and weight, does not exactly reproduce the anatomy of children. However, for public exposure the calculations with scaled child models indicate that the ICNIRP reference level may not provide a conservative estimate of the whole-body averaged SAR restriction, above 1.2 GHz for scaled 5- and 1-year-old female models, although any underestimate is by less than 20%

  4. Calculation of induced current densities and specific absorption rates (SAR) for pregnant women exposed to hand-held metal detectors

    Science.gov (United States)

    Kainz, Wolfgang; Chan, Dulciana D.; Casamento, Jon P.; Bassen, Howard I.

    2003-08-01

    The finite difference time domain (FDTD) method in combination with a well established frequency scaling method was used to calculate the internal fields and current densities induced in a simple model of a pregnant woman and her foetus, when exposed to hand-held metal detectors. The pregnant woman and foetus were modelled using a simple semi-heterogeneous model in 10 mm resolution, consisting of three different types of tissue. The model is based on the scanned shape of a pregnant woman in the 34th gestational week. Nine different representative models of hand-held metal detectors operating in the frequency range from 8 kHz to 2 MHz were evaluated. The metal detectors were placed directly on the abdomen of the computational model with a spacing of 1 cm. Both the induced current density and the specific absorption rate (SAR) are well below the recommended limits for exposure of the general public published in the ICNIRP Guidelines and the IEEE C95.1 Standard. The highest current density is 8.3 mA m-2 and the highest SAR is 26.5 µW kg-1. Compared to the limits for the induced current density recommended in the ICNIRP Guidelines, a minimum safety factor of 3 exists. Compared to the IEEE C95.1 Standard, a safety factor of 60 000 for the specific absorption rate was found. Based on the very low specific absorption rate and an induced current density below the recommended exposure limits, significant temperature rise or nerve stimulation in the pregnant woman or in the foetus can be excluded.

  5. Calculation of induced current densities and specific absorption rates (SAR) for pregnant women exposed to hand-held metal detectors

    International Nuclear Information System (INIS)

    Kainz, Wolfgang; Chan, Dulciana D; Casamento, Jon P; Bassen, Howard I

    2003-01-01

    The finite difference time domain (FDTD) method in combination with a well established frequency scaling method was used to calculate the internal fields and current densities induced in a simple model of a pregnant woman and her foetus, when exposed to hand-held metal detectors. The pregnant woman and foetus were modelled using a simple semi-heterogeneous model in 10 mm resolution, consisting of three different types of tissue. The model is based on the scanned shape of a pregnant woman in the 34th gestational week. Nine different representative models of hand-held metal detectors operating in the frequency range from 8 kHz to 2 MHz were evaluated. The metal detectors were placed directly on the abdomen of the computational model with a spacing of 1 cm. Both the induced current density and the specific absorption rate (SAR) are well below the recommended limits for exposure of the general public published in the ICNIRP Guidelines and the IEEE C95.1 Standard. The highest current density is 8.3 mA m -2 and the highest SAR is 26.5 μW kg -1 . Compared to the limits for the induced current density recommended in the ICNIRP Guidelines, a minimum safety factor of 3 exists. Compared to the IEEE C95.1 Standard, a safety factor of 60,000 for the specific absorption rate was found. Based on the very low specific absorption rate and an induced current density below the recommended exposure limits, significant temperature rise or nerve stimulation in the pregnant woman or in the foetus can be excluded

  6. Calculation of induced current densities and specific absorption rates (SAR) for pregnant women exposed to hand-held metal detectors

    Energy Technology Data Exchange (ETDEWEB)

    Kainz, Wolfgang; Chan, Dulciana D; Casamento, Jon P; Bassen, Howard I [Food and Drug Administration, Center for Devices and Radiological Health (CDRH), 12725 Twinbrook Parkway, Rockville, MD 20852 (United States)

    2003-08-07

    The finite difference time domain (FDTD) method in combination with a well established frequency scaling method was used to calculate the internal fields and current densities induced in a simple model of a pregnant woman and her foetus, when exposed to hand-held metal detectors. The pregnant woman and foetus were modelled using a simple semi-heterogeneous model in 10 mm resolution, consisting of three different types of tissue. The model is based on the scanned shape of a pregnant woman in the 34th gestational week. Nine different representative models of hand-held metal detectors operating in the frequency range from 8 kHz to 2 MHz were evaluated. The metal detectors were placed directly on the abdomen of the computational model with a spacing of 1 cm. Both the induced current density and the specific absorption rate (SAR) are well below the recommended limits for exposure of the general public published in the ICNIRP Guidelines and the IEEE C95.1 Standard. The highest current density is 8.3 mA m{sup -2} and the highest SAR is 26.5 {mu}W kg{sup -1}. Compared to the limits for the induced current density recommended in the ICNIRP Guidelines, a minimum safety factor of 3 exists. Compared to the IEEE C95.1 Standard, a safety factor of 60,000 for the specific absorption rate was found. Based on the very low specific absorption rate and an induced current density below the recommended exposure limits, significant temperature rise or nerve stimulation in the pregnant woman or in the foetus can be excluded.

  7. SAROTA: application of specific absorption rate (SAR) and over-the-air (OTA) data for the characterization of the real-life exposure due to mobile phones

    International Nuclear Information System (INIS)

    Monebhurrun, Vikass

    2013-01-01

    The RF exposure level of a mobile phone is quantified by the measurement of the specific absorption rate (SAR) under laboratory conditions. The SAR which is measured while the mobile phone is operated at maximum power level does not reflect the real-life exposure scenario since the mobile phone typically re-adjusts its power level and frequency depending on the quality of the communication link with the nearest base station. The choice of a low RF exposure device based on the comparison of the relative SAR values of mobile phones can be misleading. The real-life RF exposure also depends on the over-the-air (OTA) performance of the mobile phone. Taken independently, the two sets of data do not allow a straightforward comparison of the global RF performance amongst mobile phones. A unique and simple parameter denoted as the SAROTA index is proposed for the characterization of mobile phones with regard to both RF exposure and OTA performance. The SAROTA index provides the real-life exposure index of the mobile phone.

  8. Specific absorption rate reduction in parallel transmission by k-space adaptive radiofrequency pulse design.

    Science.gov (United States)

    Homann, Hanno; Graesslin, Ingmar; Nehrke, Kay; Findeklee, Christian; Dössel, Olaf; Börnert, Peter

    2011-02-01

    The specific absorption rate (SAR) is an important safety criterion, limiting many MR protocols with respect to the achievable contrast and scan duration. Parallel transmission enables control of the radiofrequency field in space and time and hence allows for SAR management. However, a trade-off exists between radiofrequency pulse performance and SAR reduction. To overcome this problem, in this work, parallel transmit radiofrequency pulses are adapted to the position in sampling k-space. In the central k-space, highly homogeneous but SAR-intensive radiofrequency shim settings are used to achieve optimal performance and contrast. In the outer k-space, the homogeneity requirement is relaxed to reduce the average SAR of the scan. The approach was experimentally verified on phantoms and volunteers using field echo and spin echo sequences. A reduction of the SAR by 25-50% was achieved without compromising image quality. Copyright © 2010 Wiley-Liss, Inc.

  9. A specific absorption rate reduction method for simultaneous multislice magnetic resonance imaging

    Science.gov (United States)

    Wu, Fu-Hsing; Wu, Edzer L.; Tung, Yi-Hang; Cheng, Po-Wei; Chiueh, Tzi-Dar; Chen, Jyh-Horng

    2017-04-01

    This study proposes a modified Shinnar-Le Roux method to synthesize the excitation radio frequency (RF) pulse for a 2D gradient echo (GRE) based simultaneous multi-slice (SMS) magnetic resonance imaging (MRI) with features of low specific absorption rate (SAR) and small out-of-slice ripple. This synthesis method for SMS RF pulses employs thinner slice bandwidth and lower multislice offset frequencies to reduce SAR values and adopts a weighted Parks-McClellan algorithm to reduce sidelobes. Formulas for estimating relative SAR values of the SMS pulses are also introduced. Relative SAR values and out-of-slice ripples of the proposed and typical RF pulses with different parameters are presented. In simultaneous 5-slice phantom and 3-slice human brain imaging, SMS pulses synthesized with the proposed method achieve 32% and 28% SAR values of standard pulses while providing similar image qualities. Typical RF pulses such as sinc x cos can also take advantage of the proposed method and offer lower SAR values for SMS imaging. The RF pulse synthesized using the proposed method features low SAR, small sidelobes, and consistent image quality for 2D GRE-based SMS MRI. This method is applicable to the synthesis of typical SMS RF pulses for significant SAR reduction.

  10. Comparison between experimental and predicted specific absorption rate of functionalized iron oxide nanoparticle suspensions

    Energy Technology Data Exchange (ETDEWEB)

    Yuan Yuan [Mechanical, Aerospace and Nuclear Engineering Department Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Tasciuc, Diana-Andra Borca, E-mail: borcad@rpi.edu [Mechanical, Aerospace and Nuclear Engineering Department Rensselaer Polytechnic Institute, Troy, NY 12180 (United States)

    2011-10-15

    Radio-frequency heated magnetic nanoaparticle suspensions have potential applications in cancer hyperthermia. To optimize these systems for hyperthermia applications it is important to be able to predict how their heat generation or specific absorption rate (SAR) is influenced by various factors, including nanoparticle coating or functionalization and aggregation. However, at present it is unclear how well-existing models predict experimental SAR results. Direct comparisons between predicted and measured SAR are scarce, despite an abundance of works reporting on heat generation rate of various magnetic nanoparticles suspensions. The main objective of this paper is to experimentally assess the validity of current models for SAR and extract information on the effects of coating and aggregation on heat generation rate. In this context, AC susceptibility and magnetization of suspensions of uncoated particles, as well as particles with aminosilane and carboxymethyl-dextran functionalizations, were measured. These properties were then used to predict the heat generation rate in alternating magnetic field starting from first principles, which was then compared to measured SAR. It was found that experimental SAR agrees relatively well with predictions (by a factor of two) when using experimental susceptibility values for the SAR calculation. However, for uncoated and amine-functionalized particles poor agreement (more than an order of magnitude difference) was found when the experimental susceptibility was substituted with predictions based on the Debye model. This apparent discrepancy is attributed to dipolar interactions between nanoparticles within aggregates in these samples, which enhances the imaginary part of the susceptibility and, consequently, the SAR values. The results also suggest that the thermal resistance effect of the coating has little influence on the SAR. - Highlights: > Thermal resistance of nanoparticle coating has little impact on heat dissipation

  11. Comparison of FDTD-calculated specific absorption rate in adults and children when using a mobile phone at 900 and 1800 MHz

    International Nuclear Information System (INIS)

    MartInez-Burdalo, M; MartIn, A; Anguiano, M; Villar, R

    2004-01-01

    In this paper, the specific absorption rate (SAR) in scaled human head models is analysed to study possible differences between SAR in the heads of adults and children and for assessment of compliance with the international safety guidelines, while using a mobile phone. The finite-difference time-domain method (FDTD) has been used for calculating SAR values for models of both children and adults, at 900 and 1800 MHz. Maximum 1 g averaged SAR (SAR 1g ) and maximum 10 g averaged SAR (SAR 10g ) have been calculated in adults and scaled head models for comparison and assessment of compliance with ANSI/IEEE and European guidelines. Results show that peak SAR 1g and peak SAR 10g all trend downwards with decreasing head size but as head size decreases, the percentage of energy absorbed in the brain increases. So, higher SAR in children's brains can be expected depending on whether the thickness of their skulls and surrounding tissues actually depends on age. The SAR in eyes of different sizes, as a critical organ, has also been studied and very similar distributions for the full size and the scaled models have been obtained. Standard limits can only be exceeded in the unpractical situation where the antenna is located at a very short distance in front of the eye

  12. Hysteresis losses and specific absorption rate measurements in magnetic nanoparticles for hyperthermia applications.

    Science.gov (United States)

    Coïsson, Marco; Barrera, Gabriele; Celegato, Federica; Martino, Luca; Kane, Shashank N; Raghuvanshi, Saroj; Vinai, Franco; Tiberto, Paola

    2017-06-01

    Magnetic hysteresis loops areas and hyperthermia on magnetic nanoparticles have been studied with the aim of providing reliable and reproducible methods of measuring the specific absorption rate (SAR). The SAR of Fe 3 O 4 nanoparticles with two different mean sizes, and Ni 1-x Zn x Fe 2 O 4 ferrites with 0 ≤ x ≤ 0.8 has been measured with three approaches: static hysteresis loops areas, dynamic hysteresis loops areas and hyperthermia of a water solution. For dynamic loops and thermometric measurements, specific experimental setups have been developed, that operate at comparable frequencies (≈ 69kHz and ≈ 100kHz respectively) and rf magnetic field peak values (up to 100mT). The hyperthermia setup has been fully modelled to provide a direct measurement of the SAR of the magnetic nanoparticles by taking into account the heat exchange with the surrounding environment in non-adiabatic conditions and the parasitic heating of the water due to ionic currents. Dynamic hysteresis loops are shown to provide an accurate determination of the SAR except for superparamagnetic samples, where the boundary with a blocked regime could be crossed in dynamic conditions. Static hysteresis loops consistently underestimate the specific absorption rate but can be used to select the most promising samples. A means of reliably measure SAR of magnetic nanoparticles by different approaches for hyperthermia applications is presented and its validity discussed by comparing different methods. This work fits within the general subject of metrological traceability in medicine with a specific focus on magnetic hyperthermia. This article is part of a Special Issue entitled "Recent Advances in Bionanomaterials" Guest Editor: Dr. Marie-Louise Saboungi and Dr. Samuel D. Bader. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Application of SAR interferometry to low-rate crustal deformation fields

    Science.gov (United States)

    Vincent, Paul

    Differential SAR interferometry is applied to the study of low-rate interseismic crustal deformation fields along three regions of the San Adreas fault system: Salton Sea (southernmost region), Pinto Mountain fault (south-central region), and San Francisco Bay (northern region). New techniques are developed to analyze and model these low-rate deformation fields including constrained horizontal-vertical component deconvolution, deformation phase pattern analysis and strain field evolution modeling. Several new active faults were discovered as well as unmeasured activity on existing faults in the process of this SAR interferometry study. The feasibility and limitations of InSAR as a tool to study low-rate deformation fields is also addressed.

  14. Textile Diamond Dipole and Artificial Magnetic Conductor Performance under Bending, Wetness and Specific Absorption Rate Measurements

    Directory of Open Access Journals (Sweden)

    K. Kamardin

    2015-09-01

    Full Text Available Textile diamond dipole and Artificial Magnetic Conductor (AMC have been proposed and tested under wearable and body centric measurements. The proposed antenna and AMC sheet are entirely made of textiles for both the substrate and conducting parts, thus making it suitable for wearable communications. Directive radiation patterns with high gain are obtained with the proposed AMC sheet, hence minimizing the radiation towards the human body. In this study, wearable and body centric measurements are investigated which include bending, wetness and Specific Absorption Rate (SAR. Bending is found not to give significant effect to the antenna and AMC performance, as opposed to wetness that yields severe performance distortion. However, the original performance is retrieved once the antenna and AMC dried. Moreover, notable SAR reduction is achieved with the introduction of the AMC sheet, which is appropriate to reduce the radiation that penetrates into human flesh.

  15. The Measuring of the Gamma Dose Rate in the Air at Location of the Sar-Mountain

    International Nuclear Information System (INIS)

    Adrovic, F.; Ninkovic, M.; Adrovic, S.

    1999-01-01

    The results of the measured values of gamma dose rate in the air at the location of Sar-mountain (Balkan Peninsula) using autonomous ADL-probe Gamma Tracer system. The difference between levels of the natural background radiation and natural environment has been pointed out at the different chosen measuring overall research of natural radioactivity at the location of Sar-mountain

  16. Uncertainties in the estimation of specific absorption rate during radiofrequency alternating magnetic field induced non-adiabatic heating of ferrofluids

    International Nuclear Information System (INIS)

    Lahiri, B B; Ranoo, Surojit; Philip, John

    2017-01-01

    Magnetic fluid hyperthermia (MFH) is becoming a viable cancer treatment methodology where the alternating magnetic field induced heating of magnetic fluid is utilized for ablating the cancerous cells or making them more susceptible to the conventional treatments. The heating efficiency in MFH is quantified in terms of specific absorption rate (SAR), which is defined as the heating power generated per unit mass. In majority of the experimental studies, SAR is evaluated from the temperature rise curves, obtained under non-adiabatic experimental conditions, which is prone to various thermodynamic uncertainties. A proper understanding of the experimental uncertainties and its remedies is a prerequisite for obtaining accurate and reproducible SAR. Here, we study the thermodynamic uncertainties associated with peripheral heating, delayed heating, heat loss from the sample and spatial variation in the temperature profile within the sample. Using first order approximations, an adiabatic reconstruction protocol for the measured temperature rise curves is developed for SAR estimation, which is found to be in good agreement with those obtained from the computationally intense slope corrected method. Our experimental findings clearly show that the peripheral and delayed heating are due to radiation heat transfer from the heating coils and slower response time of the sensor, respectively. Our results suggest that the peripheral heating is linearly proportional to the sample area to volume ratio and coil temperature. It is also observed that peripheral heating decreases in presence of a non-magnetic insulating shielding. The delayed heating is found to contribute up to ∼25% uncertainties in SAR values. As the SAR values are very sensitive to the initial slope determination method, explicit mention of the range of linear regression analysis is appropriate to reproduce the results. The effect of sample volume to area ratio on linear heat loss rate is systematically studied and

  17. Uncertainties in the estimation of specific absorption rate during radiofrequency alternating magnetic field induced non-adiabatic heating of ferrofluids

    Science.gov (United States)

    Lahiri, B. B.; Ranoo, Surojit; Philip, John

    2017-11-01

    Magnetic fluid hyperthermia (MFH) is becoming a viable cancer treatment methodology where the alternating magnetic field induced heating of magnetic fluid is utilized for ablating the cancerous cells or making them more susceptible to the conventional treatments. The heating efficiency in MFH is quantified in terms of specific absorption rate (SAR), which is defined as the heating power generated per unit mass. In majority of the experimental studies, SAR is evaluated from the temperature rise curves, obtained under non-adiabatic experimental conditions, which is prone to various thermodynamic uncertainties. A proper understanding of the experimental uncertainties and its remedies is a prerequisite for obtaining accurate and reproducible SAR. Here, we study the thermodynamic uncertainties associated with peripheral heating, delayed heating, heat loss from the sample and spatial variation in the temperature profile within the sample. Using first order approximations, an adiabatic reconstruction protocol for the measured temperature rise curves is developed for SAR estimation, which is found to be in good agreement with those obtained from the computationally intense slope corrected method. Our experimental findings clearly show that the peripheral and delayed heating are due to radiation heat transfer from the heating coils and slower response time of the sensor, respectively. Our results suggest that the peripheral heating is linearly proportional to the sample area to volume ratio and coil temperature. It is also observed that peripheral heating decreases in presence of a non-magnetic insulating shielding. The delayed heating is found to contribute up to ~25% uncertainties in SAR values. As the SAR values are very sensitive to the initial slope determination method, explicit mention of the range of linear regression analysis is appropriate to reproduce the results. The effect of sample volume to area ratio on linear heat loss rate is systematically studied and the

  18. Effects of posture on FDTD calculations of specific absorption rate in a voxel model of the human body

    International Nuclear Information System (INIS)

    Findlay, R P; Dimbylow, P J

    2005-01-01

    A change in the posture of the human body can significantly affect the way in which it absorbs radiofrequency electromagnetic radiation. To study this, an anatomically realistic model of the body has been modified to develop new voxel models in postures other than the standard standing position with arms to the side. These postures were sitting, arms stretched out horizontally to the side and vertically above the head. Finite-difference time-domain (FDTD) calculations of the whole-body averaged specific energy absorption rate (SAR) have been performed from 10 MHz to 300 MHz at a resolution of 4 mm. Calculations show that the effect of a raised arm above the head posture was to increase the value of the whole-body averaged SAR at resonance by up to 35% when compared to the standard, arms by the side position. SAR values, both whole-body averaged and localized in the ankle, were used to derive the external electric field values required to produce the SAR basic restrictions of the ICNIRP guidelines. It was found that, in certain postures, external electric field reference levels alone would not provide a conservative estimate of localized SAR exposure and it would be necessary to invoke secondary reference levels on limb currents to provide compliance with restrictions

  19. Effects of posture on FDTD calculations of specific absorption rate in a voxel model of the human body

    Science.gov (United States)

    Findlay, R. P.; Dimbylow, P. J.

    2005-08-01

    A change in the posture of the human body can significantly affect the way in which it absorbs radiofrequency electromagnetic radiation. To study this, an anatomically realistic model of the body has been modified to develop new voxel models in postures other than the standard standing position with arms to the side. These postures were sitting, arms stretched out horizontally to the side and vertically above the head. Finite-difference time-domain (FDTD) calculations of the whole-body averaged specific energy absorption rate (SAR) have been performed from 10 MHz to 300 MHz at a resolution of 4 mm. Calculations show that the effect of a raised arm above the head posture was to increase the value of the whole-body averaged SAR at resonance by up to 35% when compared to the standard, arms by the side position. SAR values, both whole-body averaged and localized in the ankle, were used to derive the external electric field values required to produce the SAR basic restrictions of the ICNIRP guidelines. It was found that, in certain postures, external electric field reference levels alone would not provide a conservative estimate of localized SAR exposure and it would be necessary to invoke secondary reference levels on limb currents to provide compliance with restrictions.

  20. Effects of posture on FDTD calculations of specific absorption rate in a voxel model of the human body

    Energy Technology Data Exchange (ETDEWEB)

    Findlay, R P; Dimbylow, P J [National Radiological Protection Board, Chilton, Didcot, Oxon OX11 0RQ (United Kingdom)

    2005-08-21

    A change in the posture of the human body can significantly affect the way in which it absorbs radiofrequency electromagnetic radiation. To study this, an anatomically realistic model of the body has been modified to develop new voxel models in postures other than the standard standing position with arms to the side. These postures were sitting, arms stretched out horizontally to the side and vertically above the head. Finite-difference time-domain (FDTD) calculations of the whole-body averaged specific energy absorption rate (SAR) have been performed from 10 MHz to 300 MHz at a resolution of 4 mm. Calculations show that the effect of a raised arm above the head posture was to increase the value of the whole-body averaged SAR at resonance by up to 35% when compared to the standard, arms by the side position. SAR values, both whole-body averaged and localized in the ankle, were used to derive the external electric field values required to produce the SAR basic restrictions of the ICNIRP guidelines. It was found that, in certain postures, external electric field reference levels alone would not provide a conservative estimate of localized SAR exposure and it would be necessary to invoke secondary reference levels on limb currents to provide compliance with restrictions.

  1. Exercise, Insulin Absorption Rates, and Artificial Pancreas Control

    Science.gov (United States)

    Frank, Spencer; Hinshaw, Ling; Basu, Rita; Basu, Ananda; Szeri, Andrew J.

    2016-11-01

    Type 1 Diabetes is characterized by an inability of a person to endogenously produce the hormone insulin. Because of this, insulin must be injected - usually subcutaneously. The size of the injected dose and the rate at which the dose reaches the circulatory system have a profound effect on the ability to control glucose excursions, and therefore control of diabetes. However, insulin absorption rates via subcutaneous injection are variable and depend on a number of factors including tissue perfusion, physical activity (vasodilation, increased capillary throughput), and other tissue geometric and physical properties. Exercise may also have a sizeable effect on the rate of insulin absorption, which can potentially lead to dangerous glucose levels. Insulin-dosing algorithms, as implemented in an artificial pancreas controller, should account accurately for absorption rate variability and exercise effects on insulin absorption. The aforementioned factors affecting insulin absorption will be discussed within the context of both fluid mechanics and data driven modeling approaches.

  2. Rate of water absorption and proximate analysis of different varieties ...

    African Journals Online (AJOL)

    Water absorption and proximate composition of four varieties of maize; sweet corn, pop corn, white corn and yellow corn soaked at different temperatures and time duration were determined. Absorption increased with increase in temperatures and time but generally low at 45°C. The total average rate of hydration at different ...

  3. The absorption of carbon monoxide in COSORB solutions: absorption rate and capacity

    NARCIS (Netherlands)

    Hogendoorn, Kees; van Swaaij, Willibrordus Petrus Maria; Versteeg, Geert

    1995-01-01

    Absorption rate experiments and equilibrium experiments were carried out for the COSORB reaction at 300 K. The equilibrium data at 300 K could reasonably well be described with the following relation: [...] Determination of the kinetics and mechanism of a chemical reaction by means of absorption

  4. Soft black hole absorption rates as conservation laws

    Energy Technology Data Exchange (ETDEWEB)

    Avery, Steven G. [Brown University, Department of Physics,182 Hope St, Providence, RI, 02912 (United States); Michigan State University, Department of Physics and Astronomy,East Lansing, MI, 48824 (United States); Schwab, Burkhard UniversityW. [Harvard University, Center for Mathematical Science and Applications,1 Oxford St, Cambridge, MA, 02138 (United States)

    2017-04-10

    The absorption rate of low-energy, or soft, electromagnetic radiation by spherically symmetric black holes in arbitrary dimensions is shown to be fixed by conservation of energy and large gauge transformations. We interpret this result as the explicit realization of the Hawking-Perry-Strominger Ward identity for large gauge transformations in the background of a non-evaporating black hole. Along the way we rederive and extend previous analytic results regarding the absorption rate for the minimal scalar and the photon.

  5. An Improved Doppler Rate Estimation Approach for Sliding Spotlight SAR Data Based on the Transposition Domain

    Directory of Open Access Journals (Sweden)

    She Xiao-qiang

    2014-08-01

    Full Text Available In image processing of high-resolution sliding spotlight SAR, it is important to know the Doppler rate with accuracy; however, traditional Doppler rate estimation algorithms are not very helpful because of the azimuth spectrum folding phenomenon. In this study, an algorithm that works on the transposition domain is proposed to solve this problem. Furthermore, the algorithm is also helpful in obtaining excellent focused images by embedding it in the two-step technique. Finally, the proposed algorithm is verified using computer simulations.

  6. InSAR observations of low slip rates on the major faults of western Tibet.

    Science.gov (United States)

    Wright, Tim J; Parsons, Barry; England, Philip C; Fielding, Eric J

    2004-07-09

    Two contrasting views of the active deformation of Asia dominate the debate about how continents deform: (i) The deformation is primarily localized on major faults separating crustal blocks or (ii) deformation is distributed throughout the continental lithosphere. In the first model, western Tibet is being extruded eastward between the major faults bounding the region. Surface displacement measurements across the western Tibetan plateau using satellite radar interferometry (InSAR) indicate that slip rates on the Karakoram and Altyn Tagh faults are lower than would be expected for the extrusion model and suggest a significant amount of internal deformation in Tibet.

  7. Binding of the GTPase Sar1 to a Lipid Membrane Monolayer: Insertion and Orientation Studied by Infrared Reflection–Absorption Spectroscopy

    Directory of Open Access Journals (Sweden)

    Christian Schwieger

    2017-11-01

    Full Text Available Membrane-interacting proteins are polyphilic polymers that engage in dynamic protein–protein and protein–lipid interactions while undergoing changes in conformation, orientation and binding interfaces. Predicting the sites of interactions between such polypeptides and phospholipid membranes is still a challenge. One example is the small eukaryotic GTPase Sar1, which functions in phospholipid bilayer remodeling and vesicle formation as part of the multimeric coat protein complex (COPII. The membrane interaction of Sar1 is strongly dependent on its N-terminal 23 amino acids. By monolayer adsorption experiments and infrared reflection-absorption spectroscopy (IRRAS, we elucidate the role of lipids in inducing the amphipathicity of this N-terminal stretch, which inserts into the monolayer as an amphipathic helix (AH. The AH inserting angle is determined and is consistent with the philicities and spatial distribution of the amino acid monomers. Using an advanced method of IRRAS data evaluation, the orientation of Sar1 with respect to the lipid layer prior to the recruitment of further COPII proteins is determined. The result indicates that only a slight reorientation of the membrane-bound Sar1 is needed to allow coat assembly. The time-course of the IRRAS analysis corroborates a role of slow GTP hydrolysis in Sar1 desorption from the membrane.

  8. Rate of absorption and interfacial area of chlorine into aqueous ...

    African Journals Online (AJOL)

    aghomotsegin

    The rate of absorption predicted from developed model is compared with experimental results. They were in good agreement. ... are chlorine-water, chlorine-aqueous solution of alkaline carbonate, chlorine-aqueous alkaline ... Bulk concentration of an individual chemical species in liquid. Assuming all the reactions are at ...

  9. Determination of sedimentation rates and absorption coefficient of ...

    African Journals Online (AJOL)

    DR. MIKE HORSFALL

    particles have pores that can absorb radiation. Gamma rays have been used to study the absorption coefficients of cobalt(II) insoluble compounds (Essien and Ekpe, 1998), densities of marine sediments. (Gerland and Villinger, 1995) and soil particle-size distribution (Vaz et al., 1992). In this study, sedimentation rates of ...

  10. The absorption of carbon monoxide in COSORB solutions : absorption rate and capacity

    NARCIS (Netherlands)

    Hogendoorn, J.A.; Swaaij, W.P.M. van; Versteeg, G.F.

    1995-01-01

    Absorption rate experiments and equilibrium experiments were carried out for the COSORB reaction at 300 K. The equilibrium data at 300 K could reasonably well be described with the following relation: Keq=3.4×10^3=([CuAlCl4.tol.CO][tol])/([CO][CuAlCl4.tol2]) Determination of the kinetics and

  11. A study on transmission characteristics and specific absorption rate using impedance-matched electrodes for various human body communication.

    Science.gov (United States)

    Machida, Yuta; Yamamoto, Takahiko; Koshiji, Kohji

    2013-01-01

    Human body communication (HBC) is a new communication technology that has presented potential applications in health care and elderly support systems in recent years. In this study, which is focused on a wearable transmitter and receiver for HBC in a body area network (BAN), we performed electromagnetic field analysis and simulation using the finite difference time domain (FDTD) method with various models of the human body. Further we redesigned a number of impedance-matched electrodes to allow transmission without stubs or transformers. The specific absorption rate (SAR) and transmission characteristics S21 of these electrode structures were compared for several models.

  12. Localized specific absorption rate calculations in a realistic phantom leg at 1-30 MHz using a finite element method.

    Science.gov (United States)

    Wainwright, P R

    1999-04-01

    Protection standards for radiofrequency electromagnetic radiation are principally intended to avoid detrimental thermal effects. To this end the International Commission on Non-Ionizing Radiation Protection (ICNIRP), and national bodies such as the National Radiological Protection Board (NRPB), recommend limitations on the localized specific energy absorption rate (SAR) in various parts of the body. The role of numerical dosimetry is to estimate the SAR from measurable parameters such as external field strengths and total body currents. In recent years there have been significant advances in the sophistication of the anatomical models available, and in our knowledge of the electrical properties of the body tissues. Several groups, including NRPB, have developed mathematical phantoms from medical imaging data, such as MRI scans. It has been known for some time that under certain circumstances SAR restrictions may be violated in the ankle due to the concentration of current in a small area. In this paper the author presents calculations of the SAR distribution in a human leg in the high-frequency (HF) band. This band contains the human whole-body resonance frequency and therefore gives the strongest coupling of the body to the field. The present study uses a finite element model with variable mesh size, derived from a 2 mm resolution voxel phantom of the whole body. It also uses recently acquired data on the electrical properties of the tissues. The results are discussed in the light of the exposure standards promulgated by national and international bodies such as NRPB and ICNIRP, and it is shown that the basic SAR restrictions in the leg are ensured by a current reference level of 100 mA.

  13. Localized specific absorption rate calculations in a realistic phantom leg at 1-30 MHz using a finite element method

    International Nuclear Information System (INIS)

    Wainwright, P.R.

    1999-01-01

    Protection standards for radiofrequency electromagnetic radiation are principally intended to avoid detrimental thermal effects. To this end the International Commission on Non-Ionizing Radiation Protection (ICNIRP), and national bodies such as the National Radiological Protection Board (NRPB), recommend limitations on the localized specific energy absorption rate (SAR) in various parts of the body. The role of numerical dosimetry is to estimate the SAR from measurable parameters such as external field strengths and total body currents. In recent years there have been significant advances in the sophistication of the anatomical models available, and in our knowledge of the electrical properties of the body tissues. Several groups, including NRPB, have developed mathematical phantoms from medical imaging data, such as MRI scans. It has been known for some time that under certain circumstances SAR restrictions may be violated in the ankle due to the concentration of current in a small area. In this paper the author presents calculations of the SAR distribution in a human leg in the high-frequency (HF) band. This band contains the human whole-body resonance frequency and therefore gives the strongest coupling of the body to the field. The present study uses a finite element model with variable mesh size, derived from a 2 mm resolution voxel phantom of the whole body. It also uses recently acquired data on the electrical properties of the tissues. The results are discussed in the light of the exposure standards promulgated by national and international bodies such as NRPB and ICNIRP, and it is shown that the basic SAR restrictions in the leg are ensured by a current reference level of 100 mA. (author)

  14. The relationship between specific absorption rate and temperature elevation in anatomically based human body models for plane wave exposure from 30 MHz to 6 GHz

    Science.gov (United States)

    Hirata, Akimasa; Laakso, Ilkka; Oizumi, Takuya; Hanatani, Ryuto; Chan, Kwok Hung; Wiart, Joe

    2013-02-01

    According to the international safety guidelines/standard, the whole-body-averaged specific absorption rate (Poljak et al 2003 IEEE Trans. Electromagn. Compat. 45 141-5) and the peak spatial average SAR are used as metrics for human protection from whole-body and localized exposures, respectively. The IEEE standard (IEEE 2006 IEEE C95.1) indicates that the upper boundary frequency, over which the whole-body-averaged SAR is deemed to be the basic restriction, has been reduced from 6 to 3 GHz, because radio-wave energy is absorbed around the body surface when the frequency is increased. However, no quantitative discussion has been provided to support this description especially from the standpoint of temperature elevation. It is of interest to investigate the maximum temperature elevation in addition to the core temperature even for a whole-body exposure. In the present study, using anatomically based human models, we computed the SAR and the temperature elevation for a plane-wave exposure from 30 MHz to 6 GHz, taking into account the thermoregulatory response. As the primary result, we found that the ratio of the core temperature elevation to the whole-body-averaged SAR is almost frequency independent for frequencies below a few gigahertz; the ratio decreases above this frequency. At frequencies higher than a few gigahertz, core temperature elevation for the same whole-body averaged SAR becomes lower due to heat convection from the skin to air. This lower core temperature elevation is attributable to skin temperature elevation caused by the power absorption around the body surface. Then, core temperature elevation even for whole-body averaged SAR of 4 W kg-1 with the duration of 1 h was at most 0.8 °C, which is smaller than a threshold considered in the safety guidelines/standard. Further, the peak 10 g averaged SAR is correlated with the maximum body temperature elevations without extremities and pinna over the frequencies considered. These findings were confirmed

  15. Toward Online Adaptive Hyperthermia Treatment Planning: Correlation Between Measured and Simulated Specific Absorption Rate Changes Caused by Phase Steering in Patients

    Energy Technology Data Exchange (ETDEWEB)

    Kok, H. Petra, E-mail: H.P.Kok@amc.uva.nl [Department of Radiation Oncology, Academic Medical Center, University of Amsterdam, Amsterdam (Netherlands); Ciampa, Silvia [Department of Radiation Oncology, Academic Medical Center, University of Amsterdam, Amsterdam (Netherlands); Department of Civil Engineering and Computer Science, University of Rome Tor Vergata, Rome (Italy); Kroon-Oldenhof, Rianne de; Steggerda-Carvalho, Eva J.; Stam, Gerard van; Zum Vörde Sive Vörding, Paul J.; Stalpers, Lukas J.A.; Geijsen, Elisabeth D. [Department of Radiation Oncology, Academic Medical Center, University of Amsterdam, Amsterdam (Netherlands); Bardati, Fernando [Department of Civil Engineering and Computer Science, University of Rome Tor Vergata, Rome (Italy); Bel, Arjan; Crezee, Johannes [Department of Radiation Oncology, Academic Medical Center, University of Amsterdam, Amsterdam (Netherlands)

    2014-10-01

    Purpose: Hyperthermia is the clinical application of heat, in which tumor temperatures are raised to 40°C to 45°C. This proven radiation and chemosensitizer significantly improves clinical outcome for several tumor sites. Earlier studies of the use of pre-treatment planning for hyperthermia showed good qualitative but disappointing quantitative reliability. The purpose of this study was to investigate whether hyperthermia treatment planning (HTP) can be used more reliably for online adaptive treatment planning during locoregional hyperthermia treatments. Methods and Materials: This study included 78 treatment sessions for 15 patients with non-muscle-invasive bladder cancer. At the start of treatments, temperature rise measurements were performed with 3 different antenna settings optimized for each patient, from which the absorbed power (specific absorption rate [SAR]) was derived. HTP was performed based on a computed tomography (CT) scan in treatment position with the bladder catheter in situ. The SAR along the thermocouple tracks was extracted from the simulated SAR distributions. Correlations between measured and simulated (average) SAR values were determined. To evaluate phase steering, correlations between the changes in simulated and measured SAR values averaged over the thermocouple probe were determined for all 3 combinations of antenna settings. Results: For 42% of the individual treatment sessions, the correlation coefficient between measured and simulated SAR profiles was higher than 0.5, whereas 58% showed a weak correlation (R of <0.5). The overall correlation coefficient between measured and simulated average SAR was weak (R=0.31; P<.001). The measured and simulated changes in average SAR after adapting antenna settings correlated much better (R=0.70; P<.001). The ratio between the measured and simulated quotients of maximum and average SARs was 1.03 ± 0.26 (mean ± SD), indicating that HTP can also correctly predict the relative amplitude of

  16. Specific absorption rate variation in a brain phantom due to exposure by a 3G mobile phone: problems in dosimetry.

    Science.gov (United States)

    Behari, J; Nirala, Jay Prakash

    2013-12-01

    A specific absorption rate (SAR) measurements system has been developed for compliance testing of personal mobile phone in a brain phantom material contained in a Perspex box. The volume of the box has been chosen corresponding to the volume of a small rat and illuminated by a 3G mobile phone frequency (1718.5 MHz), and the emitted radiation directed toward brain phantom .The induced fields in the phantom material are measured. Set up to lift the plane carrying the mobile phone is run by a pulley whose motion is controlled by a stepper motor. The platform is made to move at a pre-determined rate of 2 degrees per min limited up to 20 degrees. The measured data for induced fields in various locations are used to compute corresponding SAR values and inter comparison obtained. These data are also compared with those when the mobile phone is placed horizontally with respect to the position of the animal. The SAR data is also experimentally obtained by measuring a rise in temperature due to this mobile exposures and data compared with those obtained in the previous set. To seek a comparison with the safety criteria same set of measurements are performed in 10 g phantom material contained in a cubical box. These results are higher than those obtained with the knowledge of induced field measurements. It is concluded that SAR values are sensitive to the angular position of the moving platform and are well below the safety criteria prescribed for human exposure. The data are suggestive of having a fresh look to understand the mode of electromagnetic field -bio interaction.

  17. Contrast-enhanced specific absorption rate-efficient 3D cardiac cine with respiratory-triggered radiofrequency gating.

    Science.gov (United States)

    Henningsson, Markus; Chan, Raymond H; Goddu, Beth; Goepfert, Lois A; Razavi, Reza; Botnar, Rene M; Schaeffter, Tobias; Nezafat, Reza

    2013-04-01

    To investigate the use of radiofrequency (RF) gating in conjunction with a paramagnetic contrast agent to reduce the specific absorption rate (SAR) and increase the blood-myocardium contrast in balanced steady-state free precession (bSSFP) 3D cardiac cine. RF gating was implemented by synchronizing the RF-excitation with an external respiratory sensor (bellows), which could additionally be used for respiratory gating. For reference, respiratory-gated 3D cine images were acquired without RF gating. Free-breathing 3D cine images were acquired in eight healthy subjects before and after contrast injection (Gd-BOPTA) and compared to breath-hold 2D cine. RF-gated 3D cine reduced the SAR by nearly 40% without introducing significant artifacts while providing left ventricle (LV) measurements similar to those obtained with 2D cine. The contrast-to-noise ratio (CNR) was significantly higher for 3D cine compared to 2D cine, both before and after contrast injection; however, no statistically significant CNR increase was observed for the postcontrast 3D cine compared to the precontrast acquisitions. Respiratory-triggered RF gating significantly reduces SAR in 3D cine acquisitions, which may enable a more widespread clinical use of 3D cine. Furthermore, CNR of 3D bSSFP cine is higher than of 2D and administration of Gd-BOPTA does not improve the CNR of 3D cine. Copyright © 2012 Wiley Periodicals, Inc.

  18. Subcutaneous insulin infusion: change in basal infusion rate has no immediate effect on insulin absorption rate

    International Nuclear Information System (INIS)

    Hildebrandt, P.; Birch, K.; Jensen, B.M.; Kuehl, C.

    1986-01-01

    Eight insulin-dependent diabetic patients were simultaneously given subcutaneous infusions (1.12 IU/h each) of 125 I-labeled Actrapid insulin in each side of the abdominal wall. After 24 h of infusion, the size of the infused insulin depots was measured by external counting for 5 h. The basal infusion rate was then doubled in one side and halved in the other for the next 4 h. Finally, 1.12 IU/h of insulin was given in both sides of the abdominal wall for an additional 3 h. The changes in the size of the depots were measured, and the absorption rates for each hour were calculated. During the first 5 h of infusion, the depot size was almost constant (approximately 5 IU) with an absorption rate that equaled the infusion rate. Doubling the infusion rate led to a significant increase in depot size, but the absorption rate remained unchanged for the first 3 h, and only thereafter was a significant increase seen. When the infusion rate was reduced to the initial 1.12 IU/h, the absorption rate remained elevated during the next 3 h. Correspondingly, when the infusion rate was decreased, the depot size also decreased, but the absorption rate remained unchanged for the first 3 h. The results show that a change in the basal insulin infusion rate does not lead to any immediate change in the insulin absorption rate. This should be considered when planning an insulin-infusion program that includes alteration(s) in the basal-rate setting

  19. FDTD calculations of specific energy absorption rate in a seated voxel model of the human body from 10 MHz to 3 GHz

    International Nuclear Information System (INIS)

    Findlay, R P; Dimbylow, P J

    2006-01-01

    Finite-difference time-domain (FDTD) calculations have been performed to investigate the frequency dependence of the specific energy absorption rate (SAR) in a seated voxel model of the human body. The seated model was derived from NORMAN (NORmalized MAN), an anatomically realistic voxel phantom in the standing posture with arms to the side. Exposure conditions included both vertically and horizontally polarized plane wave electric fields between 10 MHz and 3 GHz. The resolution of the voxel model was 4 mm for frequencies up to 360 MHz and 2 mm for calculations in the higher frequency range. The reduction in voxel size permitted the calculation of SAR at these higher frequencies using the FDTD method. SAR values have been calculated for the seated adult phantom and scaled versions representing 10-, 5- and 1-year-old children under isolated and grounded conditions. These scaled models do not exactly reproduce the dimensions and anatomy of children, but represent good geometric information for a seated child. Results show that, when the field is vertically polarized, the sitting position causes a second, smaller resonance condition not seen in resonance curves for the phantom in the standing posture. This occurs at ∼130 MHz for the adult model when grounded. Partial-body SAR calculations indicate that the upper and lower regions of the body have their own resonant frequency at ∼120 MHz and ∼160 MHz, respectively, when the grounded adult model is orientated in the sitting position. These combine to produce this second resonance peak in the whole-body averaged SAR values calculated. Two resonance peaks also occur for the sitting posture when the incident electric field is horizontally polarized. For the adult model, the peaks in the whole-body averaged SAR occur at ∼180 and ∼600 MHz. These peaks are due to resonance in the arms and feet, respectively. Layer absorption plots and colour images of SAR in individual voxels show the specific regions in which the

  20. FDTD calculations of specific energy absorption rate in a seated voxel model of the human body from 10 MHz to 3 GHz

    Science.gov (United States)

    Findlay, R. P.; Dimbylow, P. J.

    2006-05-01

    Finite-difference time-domain (FDTD) calculations have been performed to investigate the frequency dependence of the specific energy absorption rate (SAR) in a seated voxel model of the human body. The seated model was derived from NORMAN (NORmalized MAN), an anatomically realistic voxel phantom in the standing posture with arms to the side. Exposure conditions included both vertically and horizontally polarized plane wave electric fields between 10 MHz and 3 GHz. The resolution of the voxel model was 4 mm for frequencies up to 360 MHz and 2 mm for calculations in the higher frequency range. The reduction in voxel size permitted the calculation of SAR at these higher frequencies using the FDTD method. SAR values have been calculated for the seated adult phantom and scaled versions representing 10-, 5- and 1-year-old children under isolated and grounded conditions. These scaled models do not exactly reproduce the dimensions and anatomy of children, but represent good geometric information for a seated child. Results show that, when the field is vertically polarized, the sitting position causes a second, smaller resonance condition not seen in resonance curves for the phantom in the standing posture. This occurs at ~130 MHz for the adult model when grounded. Partial-body SAR calculations indicate that the upper and lower regions of the body have their own resonant frequency at ~120 MHz and ~160 MHz, respectively, when the grounded adult model is orientated in the sitting position. These combine to produce this second resonance peak in the whole-body averaged SAR values calculated. Two resonance peaks also occur for the sitting posture when the incident electric field is horizontally polarized. For the adult model, the peaks in the whole-body averaged SAR occur at ~180 and ~600 MHz. These peaks are due to resonance in the arms and feet, respectively. Layer absorption plots and colour images of SAR in individual voxels show the specific regions in which the seated

  1. Definition of a parameter for a typical specific absorption rate under real boundary conditions of cellular phones in a GSM networkd

    Directory of Open Access Journals (Sweden)

    D. Gerhardt

    2003-01-01

    Full Text Available Using cellular phones the specific absorption rate (SAR as a physical value must observe established and internationally defined levels to guarantee human protection. To assess human protection it is necessary to guarantee safety under worst-case conditions (especially maximum transmitting power using cellular phones. To evaluate the exposure to electromagnetic fields under normal terms of use of cellular phones the limitations of the specific absorption rate must be pointed out. In a mobile radio network normal terms of use of cellular phones, i.e. in interconnection with a fixed radio transmitter of a mobile radio network, power control of the cellular phone as well as the antenna diagram regarding a head phantom are also significant for the real exposure. Based on the specific absorption rate, the antenna diagram regarding a head phantom and taking into consideration the power control a new parameter, the typical absorption rate (SARtyp, is defined in this contribution. This parameter indicates the specific absorption rate under average normal conditions of use. Constant radio link attenuation between a cellular phone and a fixed radio transmitter for all mobile models tested was assumed in order to achieve constant field strength at the receiving antenna of the fixed radio transmitter as a result of power control. The typical specific absorption rate is a characteristic physical value of every mobile model. The typical absorption rate was calculated for 16 different mobile models and compared with the absorption rate at maximum transmitting power. The results confirm the relevance of the definition of this parameter (SARtyp as opposed to the specific absorption rate as a competent and applicable method to establish the real mean exposure from a cellular phone in a mobile radio network. The typical absorption rate provides a parameter to assess electromagnetic fields of a cellular phone that is more relevant to the consumer.

  2. B1-based SAR reconstruction using contrast source inversion-electric properties tomography (CSI-EPT)

    NARCIS (Netherlands)

    Balidemaj, Edmond; van den Berg, Cornelis A T; van Lier, A.L.H.M.W.; Nederveen, Aart J; Stalpers, Lukas J A; Crezee, Hans; Remis, Rob F

    Specific absorption rate (SAR) assessment is essential for safety purposes during MR acquisition. Online SAR assessment is not trivial and requires, in addition, knowledge of the electric tissue properties and the electric fields in the human anatomy. In this study, the potential of the recently

  3. B1-based SAR reconstruction using contrast source inversion-electric properties tomography (CSI-EPT)

    NARCIS (Netherlands)

    Balidemaj, Edmond; van den Berg, Cornelis A. T.; van Lier, Astrid L. H. M. W.; Nederveen, Aart J.; Stalpers, Lukas J. A.; Crezee, Hans; Remis, Rob F.

    2017-01-01

    Specific absorption rate (SAR) assessment is essential for safety purposes during MR acquisition. Online SAR assessment is not trivial and requires, in addition, knowledge of the electric tissue properties and the electric fields in the human anatomy. In this study, the potential of the recently

  4. B1-based SAR reconstruction using contrast source inversion–electric properties tomography (CSI-EPT)

    NARCIS (Netherlands)

    Balidemaj, E.; van den Berg, CAT; van Lier, ALHMW; Nederveen, AJ; Stalpers, LJA; Crezee, H; Remis, R.F.

    2016-01-01

    Specific absorption rate (SAR) assessment is essential for safety purposes during MR acquisition. Online SAR assessment is not trivial and requires, in addition, knowledge of the electric tissue properties and the electric fields in the human anatomy. In this study, the potential of the recently

  5. SAR Study of Mobile Phones as a function of Antenna Q

    DEFF Research Database (Denmark)

    Bahramzy, Pevand; Svendsen, Simon; Jagielski, Ole

    2015-01-01

    High-Q tunable antennas are good alternatives to low-Q passive antennas because the antenna size can be smaller while covering the required long-term evolution (LTE) frequency bands. However, among other things, specific absorption rate (SAR) can become a challenge due to the relative high curren...... SAR values depend on total losses of the mock-up (MU)....

  6. Improving peak local SAR prediction in parallel transmit using in situ S-matrix measurements

    NARCIS (Netherlands)

    Restivo, Matthew; Raaijmakers, AJE; van den Berg, CAT; Luijten, Peter; Hoogduin, Hans

    PURPOSE: Peak local specific absorption rate (pSAR10g) is an important parameter used to determine patient safety during radiofrequency transmission. pSAR10g predictions for parallel transmit MRI are affected by the level of coupling exhibited by a modeled array in the simulation environment.

  7. The relationship between specific absorption rate and temperature elevation in anatomically based human body models for plane wave exposure from 30 MHz to 6 GHz.

    Science.gov (United States)

    Hirata, Akimasa; Laakso, Ilkka; Oizumi, Takuya; Hanatani, Ryuto; Chan, Kwok Hung; Wiart, Joe

    2013-02-21

    According to the international safety guidelines/standard, the whole-body-averaged specific absorption rate (Poljak et al 2003 IEEE Trans. Electromagn. Compat. 45 141-5) and the peak spatial average SAR are used as metrics for human protection from whole-body and localized exposures, respectively. The IEEE standard (IEEE 2006 IEEE C95.1) indicates that the upper boundary frequency, over which the whole-body-averaged SAR is deemed to be the basic restriction, has been reduced from 6 to 3 GHz, because radio-wave energy is absorbed around the body surface when the frequency is increased. However, no quantitative discussion has been provided to support this description especially from the standpoint of temperature elevation. It is of interest to investigate the maximum temperature elevation in addition to the core temperature even for a whole-body exposure. In the present study, using anatomically based human models, we computed the SAR and the temperature elevation for a plane-wave exposure from 30 MHz to 6 GHz, taking into account the thermoregulatory response. As the primary result, we found that the ratio of the core temperature elevation to the whole-body-averaged SAR is almost frequency independent for frequencies below a few gigahertz; the ratio decreases above this frequency. At frequencies higher than a few gigahertz, core temperature elevation for the same whole-body averaged SAR becomes lower due to heat convection from the skin to air. This lower core temperature elevation is attributable to skin temperature elevation caused by the power absorption around the body surface. Then, core temperature elevation even for whole-body averaged SAR of 4 W kg(-1) with the duration of 1 h was at most 0.8 °C, which is smaller than a threshold considered in the safety guidelines/standard. Further, the peak 10 g averaged SAR is correlated with the maximum body temperature elevations without extremities and pinna over the frequencies considered. These findings

  8. Rate of absorption and interfacial area of chlorine into aqueous ...

    African Journals Online (AJOL)

    aghomotsegin

    Due to excellent mass transfer characteristics with energy efficiency jet ejectors can be used in place of conventional countercurrent systems, namely, packed bed contactors as well as venturi scrubbers, cyclones and airlift pumps. The removal of chlorine from certain gases by absorption in aqueous solutions of sodium ...

  9. Study of the Qinghai-Tibetan Plateau Permafrost Active Layer Thickening Rate Using ALOS-1/-2 Interferometric SAR Data

    Science.gov (United States)

    Jia, Y.; Shum, C. K.; Kim, J.; Lu, Z.; Kuo, C. Y.; Zhang, L.; Ding, X.

    2016-12-01

    The Qinghai-Tibetan Plateau(QTP) is the world's largest and the highest plateau with distinct and competing surface and subsurface processes. It is the Third Pole and the World Water Tower, owing to its vast ice reservoir with the largest number of glaciers in the world. The QTP is covered by a large (1.3 to 1.6 million km2) layer of discontinuous and sporadic alpine permafrost, and is the origin of the largest rivers across Asia, feeding water to billions of people downstream. One such origin is the Three-River Headwater System, comprising of the mighty Yangtze, Yellow, and Lancang/Mekong Rivers, a subject of this study. The thawing over QTP permafrost regions is thought to be more severe compared with other high latitude permafrost regions by the fact that most of the permafrost is warm. During the past few decades, 10% permafrost has degraded. The overall mean active layer (AL) thickening rates over the QTP from model studies were 1.4 cm yr-1 during 1980-2001 and approximately 6.3 cm yr-1 during 2006-2010, based on soil temperature profiles for 27 monitoring sites along Qinghai-Tibetan railway (QTR). Here we report on a study on quantifying AL thickening rate in the northern QTP along the QTR, using ALOS-1/-2 InSAR observed land subsidence and AL thickness modeling. We have characterized high spatial resolution (30 m) and spatially varying ALT thickening rates, 2007-2010, along the QTR's large permafrost areas (> 10,000 km2). InSAR measured subsidence rates over various thermokarst surfaces in the study region are then converted to AL thickening rates using models with estimates ranging from 2.0 cm yr-1 to 10.7 cm yr-1. Comparisons with five borehole in situ sites showed excellent agreements with r2 >0.9. Using the ALOS-1/-2 InSAR data, we have further studied the plausible contribution of permafrost in NE QTP to the Yangtze headwater runoff near the Tuotuo river.

  10. Analysis of specific absorption rate and internal electric field in human biological tissues surrounding an air-core coil-type transcutaneous energy transmission transformer.

    Science.gov (United States)

    Shiba, Kenji; Zulkifli, Nur Elina Binti; Ishioka, Yuji

    2017-06-01

    In this study, we analyzed the internal electric field E and specific absorption rate (SAR) of human biological tissues surrounding an air-core coil transcutaneous energy transmission transformer. Using an electromagnetic simulator, we created a model of human biological tissues consisting of a dry skin, wet skin, fat, muscle, and cortical bone. A primary coil was placed on the surface of the skin, and a secondary coil was located subcutaneously inside the body. The E and SAR values for the model representing a 34-year-old male subject were analyzed using electrical frequencies of 0.3-1.5 MHz. The transmitting power was 15 W, and the load resistance was 38.4 Ω. The results showed that the E values were below the International Commission on Non-ionizing Radiation Protection (ICNIRP) limit for the general public exposure between the frequencies of 0.9 and 1.5 MHz, and SAR values were well below the limit prescribed by the ICNIRP for the general public exposure between the frequencies of 0.3 and 1.2 MHz.

  11. Determination of sedimentation rates and absorption coefficient of ...

    African Journals Online (AJOL)

    2+ has a higher sedimentation rate of 5.10x10-2 s-1 while Ni2+ has the lowest sedimentation rates of 1.10 x10-3. The rate of sedimentation of the metal carbonates decreased in the order: Zn2+ > Cd2+ > Cu2+ > Co2+ > Ni2+. The order ...

  12. Analysis of in situ electric field and specific absorption rate in human models for wireless power transfer system with induction coupling.

    Science.gov (United States)

    Sunohara, Tetsu; Hirata, Akimasa; Laakso, Ilkka; Onishi, Teruo

    2014-07-21

    This study investigates the specific absorption rate (SAR) and the in situ electric field in anatomically based human models for the magnetic field from an inductive wireless power transfer system developed on the basis of the specifications of the wireless power consortium. The transfer system consists of two induction coils covered by magnetic sheets. Both the waiting and charging conditions are considered. The transfer frequency considered in this study is 140 kHz, which is within the range where the magneto-quasi-static approximation is valid. The SAR and in situ electric field in the chest and arm of the models are calculated by numerically solving the scalar potential finite difference equation. The electromagnetic modelling of the coils in the wireless power transfer system is verified by comparing the computed and measured magnetic field distributions. The results indicate that the peak value of the SAR averaged over a 10 g of tissue and that of the in situ electric field are 72 nW kg(-1) and 91 mV m(-1) for a transmitted power of 1 W, Consequently, the maximum allowable transmitted powers satisfying the exposure limits of the SAR (2 W kg(-1)) and the in situ electric field (18.9 V m(-1)) are found to be 28 MW and 43 kW. The computational results show that the in situ electric field in the chest is the most restrictive factor when compliance with the wireless power transfer system is evaluated according to international guidelines.

  13. Effects of animal activity on the absorption rate of soils in the ...

    African Journals Online (AJOL)

    The rates of absorption into various microsites in Karoo soils were compared. The absorption of water by hard, bare intershrub soils was significantly increased by the presence of emergence holes of adult cicadas and near nest-mounds of the harvester ant Messor capensis. Both these insects play an important role in ...

  14. Poster - Thur Eve - 13: Quantifying specific absorption rate of shielded RF coils through electromagnetic simulations for 7-T MRI.

    Science.gov (United States)

    Belliveau, J-G; Gilbert, K M; Abou-Khousa, M; Menon, R S

    2012-07-01

    Ultra-high field MRI has many advantages such as increasing spatial resolution and exploiting contrast never before seen in-vivo. This contrast has been shown to be beneficial for many applications such as monitoring early and late effect to radiation therapy and transient changes during disease to name a few. However, at higher field strengths the RF wave, needed to for transmitting and receiving signal, approaches that of the head. This leads to constructive and deconstructive interference and a non -uniform flip angle over the volume being imaged. A transmit or transceive RF surface coil arrays is currently a method of choice to overcome this problem; however, mutual inductance between elements poses a significant challenge for the designer. A method to decouple elements in such an array is by using circumferential shielding; however, the potential benefits and/or disadvantages have not been investigated. This abstract primarily focuses on understanding power deposition - measured through Specific Absorption Rate - in the sample using circumferentially shielded RF coils. Various geometries of circumferentially shielded coils are explored to determine the behaviour of shield width and its effect on required transmit power and power deposition to the sample. Our results indicate that there is an optimization on shield width depending on the imaging depth. Additionally, the circumferential shield focuses the field more than unshielded coils, meaning that slight SAR may even be lower for circumferential shielded RF coils in array. © 2012 American Association of Physicists in Medicine.

  15. SAR measurement in MRI: an improved method

    Science.gov (United States)

    Romano, Rocco; Acernese, Fausto; Indovina, Pietro Luigi; Barone, Fabrizio

    2009-03-01

    During an MR procedure, the patient absorbs a portion of the transmitted RF energy, which may result in tissue heating and other adverse effects, such as alterations in visual, auditory and neural functions. The Specific Absorption Rate (SAR), in W/kg, is the RF power absorbed per unit mass of tissue and is one of the most important parameters related with thermal effects and acts as a guideline for MRI safety. Strict limits to the SAR levels are imposed by patient safety international regulations (CEI - EN 60601 - 2 - 33) and SAR measurements are required in order to verify its respect. The recommended methods for mean SAR measurement are quite problematic and often require a maintenance man intervention and long stop machine. For example, in the CEI recommended pulse energy method, the presence of a maintenance man is required in order to correctly connect the required instrumentation; furthermore, the procedure is complex and requires remarkable processing and calculus. Simpler are the calorimetric methods, also if in this case long acquisition times are required in order to have significant temperature variations and accurate heat capacity knowledge (CEI - EN 60601 - 2- 33). The phase transition method is a new method to measure SAR in MRI which has the advantages to be very simple and to overcome all the typical calorimetric method problems. It does not require in gantry temperature measurements, any specific heat or heat capacity knowledge, but only mass and time measurement. Furthermore, in this method, it is possible to show that all deposited SAR power can be considered acquired and measured.

  16. Water Absorption Rate Prediction of PMMA and Its Composites Using BP Neural Network

    Directory of Open Access Journals (Sweden)

    Chen Kui

    2016-01-01

    Full Text Available Referring to water absorption rate of poly (methyl methacrylate (PMMA and its composites is hard to obtain under some working conditions, BP neural network prediction model was constructed. Regarding water absorption rate predictions of exfoliated PMMA/MMT nanocomposites in 0.1 mol/L H2SO4 solution, 0.1 mol/L NaOH solution and deionized water respectively as examples, the applicability of model established in water absorption rate prediction of PMMA and its composites was researched. The results show that the relative errors between prediction value obtained from model established and actual value of water absorption rate of composites soaking 63min in three kinds of mediums are 1.50%, 0.47% and 1.04% respectively, prediction accuracy is higher than that (relative errors are 3.89%, 3.40% and 4.43% respectively obtained from GM (1, 1 model obviously. BP neural network can be used to predict water absorption rate of PMMA and its composites.

  17. Numerical analysis of specific absorption rate in the human head due to a 13.56 MHz RFID-based intra-ocular pressure measurement system

    International Nuclear Information System (INIS)

    Hirtl, Rene; Schmid, Gernot

    2013-01-01

    A modern wireless intra-ocular pressure monitoring system, based on 13.56 MHz inductively coupled data transmission, was dosimetrically analyzed with respect to the specific absorption rate (SAR) induced inside the head and the eye due to the electromagnetic field exposure caused by the reader antenna of the transmission system. The analysis was based on numerical finite difference time domain computations using a high resolution anatomical eye model integrated in a modern commercially available anatomical model of a male head. Three different reader antenna configurations, a 7-turn elliptic (30 mm × 50 mm) antenna at 12 mm distance from the eye, a flexible circular antenna (60 mm diameter, 8 turns on 2 mm substrate) directly attached to the skin, and a circular 7-turn antenna (30 mm diameter at 12 mm distance to the eye) were analyzed, respectively. Possible influences of the eye-lid status (closed or opened) and the transponder antenna contained in a contact lens directly attached to the eye were taken into account. The results clearly demonstrated that for typical reader antenna currents required for proper data transmission, the SAR values remain far below the limits for localized exposure of the head, as defined by the International Commission for Non-Ionizing Radiation Protection. Particularly the induced SAR inside the eye was found to be substantially (orders of magnitudes for typical reader antenna currents in the order of 1 A turn) below values which have been reported to be critical with respect to thermally induced adverse health effects in eye tissues. (note)

  18. 7T MRI-Histologic Correlation Study of Low Specific Absorption Rate T2-Weighted GRASE Sequences in the Detection of White Matter Involvement in Multiple Sclerosis.

    Science.gov (United States)

    Bagnato, Francesca; Hametner, Simon; Pennell, David; Dortch, Richard; Dula, Adrienne N; Pawate, Siddharama; Smith, Seth A; Lassmann, Hans; Gore, John C; Welch, Edward B

    2015-01-01

    The high value of the specific absorption rate (SAR) of radio-frequency (RF) energy arising from the series of RF refocusing pulses in T2-weighted (T2-w) turbo spin echo (TSE) MRI hampers its clinical application at 7.0 Tesla (7T). T2-w gradient and spin echo (GRASE) uses the speed from gradient refocusing in combination with the chemical-shift/static magnetic field (B0) inhomogeneity insensitivity from spin-echo refocusing to acquire T2-w images with a limited number of refocusing RF pulses, thus reducing SAR. To investigate whether low SAR T2-w GRASE could replace T2-w TSE in detecting white matter (WM) disease in MS patients imaged at 7T. The .7 mm3 isotropic T2-w TSE and T2-w GRASE images with variable echo times (TEs) and echo planar imaging (EPI) factors were obtained on a 7T scanner from postmortem samples of MS brains. These samples were derived from brains of 3 female MS patients. WM lesions (WM-Ls) and normal-appearing WM (NAWM) signal intensity, WM-Ls/NAWM contrast-to-noise ratio (CNR) and MRI/myelin staining sections comparisons were obtained. GRASE sequences with EPI factor/TE = 3/50 and 3/75 ms were comparable to the SE technique for measures of CNR in WM-Ls and NAWM and for detection of WM-Ls. In all sequences, however, identification of areas with remyelination, Wallerian degeneration, and gray matter demyelination, as depicted by myelin staining, was not possible. T2-w GRASE images may replace T2-w TSE for clinical use. However, even at 7T, both sequences fail in detecting and characterizing MS disease beyond visible WM-Ls. Copyright © 2015 by the American Society of Neuroimaging.

  19. SARS - Diagnosis

    Indian Academy of Sciences (India)

    SARS - Diagnosis. Mainly by exclusion of known causes of atypical pneumonia; * X ray Chest; * PCR on body fluids- primers defined by WHO centres available from website.-ve result does not exclude SARS. * Sequencing of amplicons; * Viral Cultures – demanding; * Antibody tests.

  20. Numerical examinations of simplified spondylodesis models concerning energy absorption in magnetic resonance imaging

    Directory of Open Access Journals (Sweden)

    Hadert Nicole

    2016-09-01

    Full Text Available Metallic implants in magnetic resonance imaging (MRI are a potential safety risk since the energy absorption may increase temperature of the surrounding tissue. The temperature rise is highly dependent on implant size. Numerical examinations can be used to calculate the energy absorption in terms of the specific absorption rate (SAR induced by MRI on orthopaedic implants. This research presents the impact of titanium osteosynthesis spine implants, called spondylodesis, deduced by numerical examinations of energy absorption in simplified spondylodesis models placed in 1.5 T and 3.0 T MRI body coils. The implants are modelled along with a spine model consisting of vertebrae and disci intervertebrales thus extending previous investigations [1], [2]. Increased SAR values are observed at the ends of long implants, while at the center SAR is significantly lower. Sufficiently short implants show increased SAR along the complete length of the implant. A careful data analysis reveals that the particular anatomy, i.e. vertebrae and disci intervertebrales, has a significant effect on SAR. On top of SAR profile due to the implant length, considerable SAR variations at small scale are observed, e.g. SAR values at vertebra are higher than at disc positions.

  1. Experimental determination of the absorption rate of unattached radon progeny from respiratory tract to blood

    International Nuclear Information System (INIS)

    Butterweck, G.; Schuler, Ch.; Vessl, G.; Mueller, R.; Marsh, J.W.; Thrift, S.; Birchall, A.

    2002-01-01

    An exposure methodology was developed for the determination of the absorption rate of unattached radon progeny deposited in the human respiratory tract to blood. Twenty-one volunteers were exposed in a radon chamber during well-controlled aerosol and radon progeny conditions, with predominantly unattached radon daughters. Special efforts were made to restrict the dose to the volunteers to an absolute maximum of 0.08 mSv. Measurements of radon gas and radon progeny in blood samples of these volunteers indicated absorption half times of 20 min to 60 min. Former determinations, mainly performed with much larger aerosol particles of diameters between 100 nm and 1000 nm, implied absorption half times around 10 h. This indicates that the absorption of radon decay products from ciliated airways into blood is dependent upon particle size and particle composition. (author)

  2. Energy absorption at high strain rate of glass fiber reinforced mortars

    Directory of Open Access Journals (Sweden)

    Fenu Luigi

    2015-01-01

    Full Text Available In this paper, the dynamic behaviour of cement mortars reinforced with glass fibers was studied. The influence of the addition of glass fibers on energy absorption and tensile strength at high strain-rate was investigated. Static tests in compression, in tension and in bending were first performed. Dynamic tests by means of a Modified Hopkinson Bar were then carried out in order to investigate how glass fibers affected energy absorption and tensile strength at high strain-rate of the fiber reinforced mortar. The Dynamic Increase Factor (DIF was finally evaluated.

  3. Mobile phone types and SAR characteristics of the human brain

    Science.gov (United States)

    Lee, Ae-Kyoung; Hong, Seon-Eui; Kwon, Jong-Hwa; Choi, Hyung-Do; Cardis, Elisabeth

    2017-04-01

    Mobile phones differ in terms of their operating frequency, outer shape, and form and location of the antennae, all of which affect the spatial distributions of their electromagnetic field and the level of electromagnetic absorption in the human head or brain. For this paper, the specific absorption rate (SAR) was calculated for four anatomical head models at different ages using 11 numerical phone models of different shapes and antenna configurations. The 11 models represent phone types accounting for around 86% of the approximately 1400 commercial phone models released into the Korean market since 2002. Seven of the phone models selected have an internal dual-band antenna, and the remaining four possess an external antenna. Each model was intended to generate an average absorption level equivalent to that of the same type of commercial phone model operating at the maximum available output power. The 1 g peak spatial SAR and ipsilateral and contralateral brain-averaged SARs were reported for all 11 phone models. The effects of the phone type, phone position, operating frequency, and age of head models on the brain SAR were comprehensively determined.

  4. Mobile phone types and SAR characteristics of the human brain.

    Science.gov (United States)

    Lee, Ae-Kyoung; Hong, Seon-Eui; Kwon, Jong-Hwa; Choi, Hyung-Do; Cardis, Elisabeth

    2017-04-07

    Mobile phones differ in terms of their operating frequency, outer shape, and form and location of the antennae, all of which affect the spatial distributions of their electromagnetic field and the level of electromagnetic absorption in the human head or brain. For this paper, the specific absorption rate (SAR) was calculated for four anatomical head models at different ages using 11 numerical phone models of different shapes and antenna configurations. The 11 models represent phone types accounting for around 86% of the approximately 1400 commercial phone models released into the Korean market since 2002. Seven of the phone models selected have an internal dual-band antenna, and the remaining four possess an external antenna. Each model was intended to generate an average absorption level equivalent to that of the same type of commercial phone model operating at the maximum available output power. The 1 g peak spatial SAR and ipsilateral and contralateral brain-averaged SARs were reported for all 11 phone models. The effects of the phone type, phone position, operating frequency, and age of head models on the brain SAR were comprehensively determined.

  5. Chromatographic determination of the rate and extent of absorption of air pollutants by sea water

    International Nuclear Information System (INIS)

    Nikolakaki, S.; Vassilakos, C.; Katsanos, N.A.

    1994-01-01

    A simple chromatographic method is developed to determine the rate constant for expulsion of an air pollutant from water or its diffusion parameter in the liquid, the rate constant for chemical reaction of the pollutant with water, its mass transfer coefficient in the liquid, and the partition coefficient between liquid water and air. From these physicochemical parameters, the absorption rate by sea water and, therefore, the depletion rate of a polluting substance from the air can be calculated, together with the equilibrium state of this absorption. The method has been applied to nitrogen dioxide being absorbed by triple-distilled water and by sea water, at various temperatures. From the temperature variation of the reaction rate constant and of the partition coefficient, the activation energy for the reaction and the differential heat of solution were determined. (orig.)

  6. Variational finite element method to study the absorption rate of drug ...

    African Journals Online (AJOL)

    M.A. Khanday

    2014-11-25

    Nov 25, 2014 ... Saxena15 used FEM to study the drug distribution in TDD systems in steady state case by making use of quadratic shape function. Most of the models have taken into consideration ... absorption rate is decreasing function of drug concentration. .... Lagrange's interpolation formula has been used and the.

  7. Variational finite element method to study the absorption rate of drug ...

    African Journals Online (AJOL)

    Methods: The finite element method has been used to obtain the solution of the mass diffusion equation with appropriate boundary conditions. The tissue absorption rate of drug has been taken as the decreasing function of drug concentration from the skin surface towards the target site. The concentration at nodal points ...

  8. Determination of water absorption rate of palm kernel shells as an ...

    African Journals Online (AJOL)

    Sawdust, for instance, which is about the most commonly used organic pore agent is known to have high water absorption rates. This is in addition to the inability of the user to have it from one grade of wood-hard wood which is preferred. These factors amount to various drawbacks in the insulating refractory bricks produced ...

  9. The effect of gaze angle on the evaluations of SAR and temperature rise in human eye under plane-wave exposures from 0.9 to 10 GHz

    International Nuclear Information System (INIS)

    Diao, Yinliang; Leung, Sai-Wing; Sun, Weinong; Siu, Yun-Ming; Kong, Richard; Hung Chan, Kwok

    2016-01-01

    This article investigates the effect of gaze angle on the specific absorption rate (SAR) and temperature rise in human eye under electromagnetic exposures from 0.9 to 10 GHz. Eye models in different gaze angles are developed based on bio-metric data. The spatial-average SARs in eyes are investigated using the finite-difference time-domain method, and the corresponding maximum temperature rises in lens are calculated by the finite-difference method. It is found that the changes in the gaze angle produce a maximum variation of 35, 12 and 20 % in the eye-averaged SAR, peak 10 g average SAR and temperature rise, respectively. Results also reveal that the eye-averaged SAR is more sensitive to the changes in the gaze angle than peak 10 g average SAR, especially at higher frequencies. (authors)

  10. Assessment of induced SAR in children exposed to electromagnetic plane waves between 10 MHz and 5.6 GHz

    International Nuclear Information System (INIS)

    Bakker, J F; Paulides, M M; Van Rhoon, G C; Christ, A; Kuster, N

    2010-01-01

    To avoid potentially adverse health effects of electromagnetic fields (EMF), the International Commission on Non-Ionizing Radiation Protection (ICNIRP) has defined EMF reference levels from the basic restrictions on the induced whole-body-averaged specific absorption rate (SAR wb ) and the peak 10 g spatial-averaged SAR (SAR 10g ). The objective of this study is to assess if the SAR in children remains below the basic restrictions upon exposure at the reference levels. Finite difference time domain (FDTD) modeling was used to calculate the SAR in six children and two adults when exposed to all 12 orthogonal plane wave configurations. A sensitivity study showed an expanded uncertainty of 53% (SAR wb ) and 58% (SAR 10g ) due to variations in simulation settings and tissue properties. In this study, we found that the basic restriction on the SAR wb is occasionally exceeded for children, up to a maximum of 45% in small children. The maximum SAR 10g values, usually found at body protrusions, remain under the limit for all scenarios studied. Our results are in good agreement with the literature, suggesting that the recommended ICNIRP reference levels may need fine tuning.

  11. Assessment of induced SAR in children exposed to electromagnetic plane waves between 10 MHz and 5.6 GHz

    Energy Technology Data Exchange (ETDEWEB)

    Bakker, J F; Paulides, M M; Van Rhoon, G C [Erasmus MC-Daniel den Hoed Cancer Center, Department of Radiation Oncology, Section Hyperthermia, PO box 5201, NL-3008 AE, Rotterdam (Netherlands); Christ, A; Kuster, N, E-mail: j.bakker@erasmusmc.n [Foundation for Research on Information Technologies in Society (IT' IS) (Switzerland)

    2010-06-07

    To avoid potentially adverse health effects of electromagnetic fields (EMF), the International Commission on Non-Ionizing Radiation Protection (ICNIRP) has defined EMF reference levels from the basic restrictions on the induced whole-body-averaged specific absorption rate (SAR{sub wb}) and the peak 10 g spatial-averaged SAR (SAR{sub 10g}). The objective of this study is to assess if the SAR in children remains below the basic restrictions upon exposure at the reference levels. Finite difference time domain (FDTD) modeling was used to calculate the SAR in six children and two adults when exposed to all 12 orthogonal plane wave configurations. A sensitivity study showed an expanded uncertainty of 53% (SAR{sub wb}) and 58% (SAR{sub 10g}) due to variations in simulation settings and tissue properties. In this study, we found that the basic restriction on the SAR{sub wb} is occasionally exceeded for children, up to a maximum of 45% in small children. The maximum SAR{sub 10g} values, usually found at body protrusions, remain under the limit for all scenarios studied. Our results are in good agreement with the literature, suggesting that the recommended ICNIRP reference levels may need fine tuning.

  12. Iodine flow rate measurement for COIL with the chemical iodine generator based on absorption spectroscopy

    Science.gov (United States)

    Zhao, Weili; Zhang, Yuelong; Zhang, Peng; Xu, Mingxiu; Jin, Yuqi; Sang, Fengting

    2015-02-01

    A dual-components absorption method based on absorption spectroscopy was described in the paper. It can easily eliminate the influence of the serious contamination and aerosol scattering on IFR measurement by utilizing the absorptions of iodine vapor and chlorine on two different wavelengths respectively. According to the character that there is no other gaseous product in the reaction besides iodine vapor, IFR in real time can be obtained by the connections of the pressure and the flow rate among chlorine remainder, iodine vapor, and the buffer gas. We used this method to measure IFR for the first time at the exit of a chemical iodine generator. The average of IFR is coincident with that calculated by chemical weighting mass.

  13. A Study Of EMR And SAR Distribution In Human Head Phantom ...

    African Journals Online (AJOL)

    power of 0.32W for both simulations were well below the limit of 1.6 W/kg of ICNIRP standard and FCC/IEEE standard of 2W/kg. Keywords: Electromagnetic radiation (EMR), Specific Absorption Rate (SAR), Electromagnetic simulation software (FEKO emss), Radio frequency field, human head, mobile phone, mobile phone ...

  14. Updated Long Term Fault Slip Rates and Seismic Hazard in the Central Alborz, Iran: New Constraints From InSAR and GPS

    Science.gov (United States)

    Weston, J. M.; Shirzaei, M.

    2015-12-01

    The Alborz mountain range, located south of the Caspian Sea, accommodates 30% of the 25 mm/yr convergence between Arabia and Eurasia. The resulting shortening and left lateral motion is distributed over several active fault zones within the Central Alborz. Despite earlier efforts using only GPS data, little is known about the long term rate of vertical deformation and aseismic slip. Several historical earthquakes have affected this region, some of the largest of these events occurred on the Mosha fault which is close to the capital city, Tehran, which has a population of over eight million. Thus, constraining the interseismic slip rates in this region is particularly important. In this study we complement existing horizontal velocities from a regional GPS network, with line of sight velocities from interferometric synthetic aperture radar (InSAR), to provide additional constraints on the vertical deformation and enhance the spatial coverage. Assuming a seismogenic depth of 30 km, based on microseismicity data, we solve for the geometry and long term slip rates on four major fault strands in this region. We obtain a long term slip rate of ~ 3 mm/yr for the Mosha and North Alborz faults, and ~ 10 mm/yr for the Khazar fault and Parchin faults. These rates and fault geometries are in agreement with earlier works, and fit the GPS data well. However, close to the fault traces there are large residuals in the InSAR data, suggesting that there is shallow creep (Khazar faults are creeping. This new observation of fault creep has direct implications for the seismic hazard in the region. On the Mosha fault we estimate a slip deficit equivalent to a Mw 7.0 event. The combination of InSAR and GPS provide vital information for assessing the interseismic deformation in the Central Alborz, and these results highlight the importance of closer monitoring of this region to better understand the seismic hazard.

  15. Intersubject local SAR variation for 7T prostate MR imaging with an eight-channel single-side adapted dipole antenna array.

    Science.gov (United States)

    Ipek, Ozlem; Raaijmakers, Alexander J; Lagendijk, Jan J; Luijten, Peter R; van den Berg, Cornelis A T

    2014-04-01

    Surface transmit arrays used in ultra-high field body MRI require local specific absorption rate (SAR) assessment. As local SAR cannot be measured directly, local SAR is determined by simulations using dielectric patient models. In this study, the inter-patient local SAR variation is investigated for 7T prostate imaging with the single-side adapted dipole antenna array. Four-dedicated dielectric models were created by segmenting Dixon water-fat separated images that were obtained from four subjects with a 1.5T scanner and the surface array in place. Electromagnetic simulations were performed to calculate the SAR distribution for each model. Radio frequency (RF) exposure variations were determined by analyzing the SAR(10g) distributions (1) with one element active, (2) using a Q-matrix eigenvalue/eigenvector approach, (3) with the maximum potential SAR in each voxel, and (4) for a phase shimmed prostate measurement. Maximum potential local SAR levels for 1 W time-averaged accepted power per transmit channel range from 4.1 to 7.1 W/kg. These variations show that one model is not sufficient to determine safe scan settings. For the operation of the surface array conservative power settings were derived based on a worst-case SAR evaluation and the most SAR-sensitive body model. Copyright © 2013 Wiley Periodicals, Inc.

  16. Ingestion Rates and Absorption Efficiencies of Abra ovata(Mollusca: Bivalvia) Fed on Macrophytobenthic Detritus

    Science.gov (United States)

    Charles, F.; Grémare, A.; Amouroux, J. M.

    1996-01-01

    Ingestion and absorption were investigated in the deposit-feeding bivalve Abra ovatafed on 14C-formaldehyde-labelled detritus derived from 11 macrophytes: Posidonia oceanica, Cystoseira compressa, Padina pavonica, Stypocaulon scoparium, Colpomenia sinuosa, Cystoseira mediterranea, Dilophus spiralis, Rissoella verruculosa, Ulva rigida, Corallina elongata andCodium vermilara . Labelling efficiency ranged from 3·2 (R. verruculosa ) to 53·0% (C. sinuosa) depending on the detritus. The stability of the labelling also varied among detritus types, and was negatively correlated with labelling efficiency. For all types of detritus, the exchanges of radioactivity between compartments were dominated by the transfer between particulate organic matter (POM) and bivalves. These transfers resulted from the interactions between the processes of ingestion, defaecation, and recycling of faeces. The coexistence of these processes together with the occasional lack of stability of the label complicated the actual determination of ingestion rates and absorption efficiencies, which necessitated the use of mathematical modelling. The model was initially composed of five compartments: Detritus, Bivalves, Dissolved organic matter (DOM), CO 2, and Faeces. Two first-order time delays were introduced to account for the production of faeces and CO 2by the bivalves. These delays resulted in the subdivision of the Bivalves compartment into three subcompartments: bivIng, bivDig, and bivAbs. The model also accounts for differences in utilization rates of detritus and faeces by the bivalves. It simulates the exchange of radioactivity between compartments and allows the quantification of ingestion and absorption efficiencies. Our results show large differences in both ingestion rates and absorption efficiencies of A. ovatafed on different types of detritus. Ingestion rates ranged between 0·16 ( C. mediterraneaand D. spiralis) and 8·65 μgOM mgDW -1 h -1( U. rigida). Absorption efficiencies ranged

  17. Sensitivity of empirical metrics of rate of absorption in bioequivalence studies.

    Science.gov (United States)

    Ring, A; Tothfalusi, L; Endrenyi, L; Weiss, M

    2000-05-01

    The sensitivity and effectiveness of indirect metrics proposed for the assessment of comparative absorption rates in bioequivalence studies [Cmax, Tmax, partial AUC (AUCp), feathered slope (SLf), intercept metric (I)] were originally tested by assuming first-order absorption. The present study re-evaluates their sensitivity performances using the more realistic inverse Gaussian (IG) model characterizing the input process for oral drug administration. Simulations were performed for both the first-order or exponential model (EX) which is determined by only one parameter, the mean absorption time (MAT = 1/k(a)), and the IG model, which additionally contains a shape parameter, the relative dispersion of absorption time distribution (CV2A). Kinetic sensitivities (KS) of the indirect metrics were evaluated from bioequivalence trials (error free data) generated with various ratios of the true parameters (MAT and CV2A) of the two formulations. The behavior of the metrics was similar with respect to changes in MAT ratios with both models: KS was low with Cmax, moderate with SLf and AUCp, and high with I and Tmax following correction for apparent lag time (Tlag). Changes of the shape parameter CV2A, however, were not detectable by Cmax, Tmax, SLf, and AUCp. Changes in both MAT and CV2A were well reflected by I with CV2A - ratio > 1. I exhibited approximately full KS also with CV2A - ratio correction was first applied for the apparent lag time. The time profile of absorption rates is insufficiently characterized by only one parameter (MAT). Indirect metrics which are sensitive enough to detect changes in the scale and shape of the input profile could be useful for bioequivalence testing. Among the tested measures, I is particularly promising when a correction is applied for Tlag.

  18. Robust time-shifted spoke pulse design in the presence of large B0 variations with simultaneous reduction of through-plane dephasing, B1+ effects, and the specific absorption rate using parallel transmission.

    Science.gov (United States)

    Guérin, Bastien; Stockmann, Jason P; Baboli, Mehran; Torrado-Carvajal, Angel; Stenger, Andrew V; Wald, Lawrence L

    2016-08-01

    To design parallel transmission spokes pulses with time-shifted profiles for joint mitigation of intensity variations due to B1+ effects, signal loss due to through-plane dephasing, and the specific absorption rate (SAR) at 7T. We derived a slice-averaged small tip angle (SA-STA) approximation of the magnetization signal at echo time that depends on the B1+ transmit profiles, the through-slice B0 gradient and the amplitude and time-shifts of the spoke waveforms. We minimize a magnitude least-squares objective based on this signal equation using a fast interior-point approach with analytical expressions of the Jacobian and Hessian. Our algorithm runs in less than three minutes for the design of two-spoke pulses subject to hundreds of local SAR constraints. On a B0/B1+ head phantom, joint optimization of the channel-dependent time-shifts and spoke amplitudes allowed signal recovery in high-B0 regions at no increase of SAR. Although the method creates uniform magnetization profiles (ie, uniform intensity), the flip angle varies across the image, which makes it ill-suited to T1-weighted applications. The SA-STA approach presented in this study is best suited to T2*-weighted applications with long echo times that require signal recovery around high B0 regions. Magn Reson Med 76:540-554, 2016. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

  19. Evaluation of Specific Absorption Rate as a Dosimetric Quantity for Electromagnetic Fields Bioeffects

    Science.gov (United States)

    Panagopoulos, Dimitris J.; Johansson, Olle; Carlo, George L.

    2013-01-01

    Purpose To evaluate SAR as a dosimetric quantity for EMF bioeffects, and identify ways for increasing the precision in EMF dosimetry and bioactivity assessment. Methods We discuss the interaction of man-made electromagnetic waves with biological matter and calculate the energy transferred to a single free ion within a cell. We analyze the physics and biology of SAR and evaluate the methods of its estimation. We discuss the experimentally observed non-linearity between electromagnetic exposure and biological effect. Results We find that: a) The energy absorbed by living matter during exposure to environmentally accounted EMFs is normally well below the thermal level. b) All existing methods for SAR estimation, especially those based upon tissue conductivity and internal electric field, have serious deficiencies. c) The only method to estimate SAR without large error is by measuring temperature increases within biological tissue, which normally are negligible for environmental EMF intensities, and thus cannot be measured. Conclusions SAR actually refers to thermal effects, while the vast majority of the recorded biological effects from man-made non-ionizing environmental radiation are non-thermal. Even if SAR could be accurately estimated for a whole tissue, organ, or body, the biological/health effect is determined by tiny amounts of energy/power absorbed by specific biomolecules, which cannot be calculated. Moreover, it depends upon field parameters not taken into account in SAR calculation. Thus, SAR should not be used as the primary dosimetric quantity, but used only as a complementary measure, always reporting the estimating method and the corresponding error. Radiation/field intensity along with additional physical parameters (such as frequency, modulation etc) which can be directly and in any case more accurately measured on the surface of biological tissues, should constitute the primary measure for EMF exposures, in spite of similar uncertainty to predict

  20. A method to approximate maximum local SAR in multichannel transmit MR systems without transmit phase information.

    Science.gov (United States)

    Orzada, Stephan; Ladd, Mark E; Bitz, Andreas K

    2017-08-01

    To calculate local specific absorption rate (SAR) correctly, both the amplitude and phase of the signal in each transmit channel have to be known. In this work, we propose a method to derive a conservative upper bound for the local SAR, with a reasonable safety margin without knowledge of the transmit phases of the channels. The proposed method uses virtual observation points (VOPs). Correction factors are calculated for each set of VOPs that prevent underestimation of local SAR when the VOPs are applied with the correct amplitudes but fixed phases. The proposed method proved to be superior to the worst-case calculation based on the maximum eigenvalue of the VOPs. The mean overestimation for six coil setups could be reduced, whereas no underestimation of the maximum local SAR occurred. In the best investigated case, the overestimation could be reduced from a factor of 3.3 to a factor of 1.7. The upper bound for the local SAR calculated with the proposed method allows a fast estimation of the local SAR based on power measurements in the transmit channels and facilitates SAR monitoring in systems that do not have the capability to monitor transmit phases. Magn Reson Med 78:805-811, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

  1. New constraints in absorptive capacity and the optimum rate of petroleum output

    Energy Technology Data Exchange (ETDEWEB)

    El Mallakh, R

    1980-01-01

    Economic policy in four oil-producing countries is analyzed within a framework that combines a qualitative assessment of the policy-making process with an empirical formulation based on historical and current trends in these countries. The concept of absorptive capacity is used to analyze the optimum rates of petroleum production in Iran, Iraq, Saudi Arabia, and Kuwait. A control solution with an econometric model is developed which is then modified for alternative development strategies based on analysis of factors influencing production decisions. The study shows the consistencies and inconsistencies between the goals of economic growth, oil production, and exports, and the constraints on economic development. Simulation experiments incorporated a number of the constraints on absorptive capacity. Impact of other constraints such as income distribution and political stability is considered qualitatively. (DLC)

  2. Specific absorption rate calculations of magnetite, using a modified linear response model for applications in magnetic hyperthermia

    Energy Technology Data Exchange (ETDEWEB)

    Hernández S, A., E-mail: h.s.alfonso@gmail.com, E-mail: meduardo2001@hotmail.com; Cano, M. E., E-mail: h.s.alfonso@gmail.com, E-mail: meduardo2001@hotmail.com [Centro Universitario de la Ciénega, Universidad de Guadalajara, Ocotlán, Jalisco (Mexico); Torres-Arenas, J., E-mail: torresare@gmail.com [Division de Ciencias e Ingenierías, Universidad de Guanajuato, León, Guanajuato (Mexico)

    2014-11-07

    Currently the absorption of electromagnetic radiation by magnetic nanoparticles is studied for biomedical applications of cancer thermotherapy. Several experiments are conduced following the framework of the Rosensweig model, in order to estimate their specific absorption rate. Nevertheless, this linear approximation involves strong simplifications which constrain their accuracy and validity range. The main aim of this work is to incorporate the deviation of the sphericity assumption in particles shapes, to improve the determination of their specific absorption rate. The correction to the effective particles volume is computed as a measure of the apparent amount of magnetic material, interacting with the external AC magnetic field. Preliminary results using the physical properties of Fe3O4 nanoparticles, exhibit an important correction in their estimated specific absorption rate, as a function of the apparent mean particles radius. Indeed, we have observed using a small deviation (6% of the apparent radius), up to 40% of the predicted specific absorption rate by the Rosensweig linear approximation.

  3. Specific absorption rate calculations of magnetite, using a modified linear response model for applications in magnetic hyperthermia

    Science.gov (United States)

    Hernández, S. A.; Cano, M. E.; Torres-Arenas, J.

    2014-11-01

    Currently the absorption of electromagnetic radiation by magnetic nanoparticles is studied for biomedical applications of cancer thermotherapy. Several experiments are conduced following the framework of the Rosensweig model, in order to estimate their specific absorption rate. Nevertheless, this linear approximation involves strong simplifications which constrain their accuracy and validity range. The main aim of this work is to incorporate the deviation of the sphericity assumption in particles shapes, to improve the determination of their specific absorption rate. The correction to the effective particles volume is computed as a measure of the apparent amount of magnetic material, interacting with the external AC magnetic field. Preliminary results using the physical properties of Fe3O4 nanoparticles, exhibit an important correction in their estimated specific absorption rate, as a function of the apparent mean particles radius. Indeed, we have observed using a small deviation (6% of the apparent radius), up to 40% of the predicted specific absorption rate by the Rosensweig linear approximation.

  4. SARS virus

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. SARS virus. Novel corona virus emerges in the new millenia. Genome sequences invariant- global isolates do not show differences of consequence.Protein spike similar. HE gene absent. 2787 nucleotides. Largest genome. Jumps species by genetic deletion.

  5. The corrosion rate and the hydrogen absorption behavior of titanium under anaerobic condition

    International Nuclear Information System (INIS)

    Suzuki, Hiroyuki; Taniguchi, Naoki

    2006-01-01

    Titanium is one of the candidate materials for overpacks as a high corrosion resistance metal. Hydrogen embrittlement is a main cause of the damage of long term integrity of titanium overpack. It is not well known about the corrosion resistance and hydrogen absorption behavior of titanium under anaerobic condition. In this study, the completely sealed ampoule test and the immersion test of titanium was carried out in aqueous solution and bentonite in order to obtain reliable data about the hydrogen generation rate and the ratio of hydrogen absorption in titanium. As the results of the tests with changing the environmental factors, obvious higher corrosion rates were observed at high carbonate (1 M) and high pH (pH 13) conditions due to the increase in the anodic reaction rate. In other condition, corrosion rate of titanium were estimated to be in the order of 10 -3 - 10 -2 μm/y. Almost all (<98%) of the hydrogen generated by corrosion was absorbed into titanium. Assuming that the time evolution of the hydrogen content in titanium follows linear law to make conservative assessment, the absorbed hydrogen content was estimated to be of 400-500 ppm in 1000 years. (author)

  6. Optimization between heating load and entropy-production rate for endoreversible absorption heat-transformers

    International Nuclear Information System (INIS)

    Sun Fengrui; Qin Xiaoyong; Chen Lingen; Wu Chih

    2005-01-01

    For an endoreversible four-heat-reservoir absorption heat-transformer cycle, for which a linear (Newtonian) heat-transfer law applies, an ecological optimization criterion is proposed for the best mode of operation of the cycle. This involves maximizing a function representing the compromise between the heating load and the entropy-production rate. The optimal relation between the ecological criterion and the COP (coefficient of performance), the maximum ecological criterion and the corresponding COP, heating load and entropy production rate, as well as the ecological criterion and entropy-production rate at the maximum heating load are derived using finite-time thermodynamics. Moreover, compared with the heating-load criterion, the effects of the cycle parameters on the ecological performance are studied by numerical examples. These show that achieving the maximum ecological criterion makes the entropy-production rate decrease by 77.0% and the COP increase by 55.4% with only 27.3% heating-load losses compared with the maximum heating-load objective. The results reflect that the ecological criterion has long-term significance for optimal design of absorption heat-transformers

  7. Analysis of the local worst-case SAR exposure caused by an MRI multi-transmit body coil in anatomical models of the human body

    Energy Technology Data Exchange (ETDEWEB)

    Neufeld, Esra; Gosselin, Marie-Christine; Murbach, Manuel; Christ, Andreas; Cabot, Eugenia; Kuster, Niels, E-mail: neufeld@itis.ethz.ch [Foundation for Research on Information Technologies in Society (IT' IS), Zeughausstr. 43, 8004 Zuerich (Switzerland)

    2011-08-07

    Multi-transmit coils are increasingly being employed in high-field magnetic resonance imaging, along with a growing interest in multi-transmit body coils. However, they can lead to an increase in whole-body and local specific absorption rate (SAR) compared to conventional body coils excited in circular polarization for the same total incident input power. In this study, the maximum increase of SAR for three significantly different human anatomies is investigated for a large 3 T (128 MHz) multi-transmit body coil using numerical simulations and a (generalized) eigenvalue-based approach. The results demonstrate that the increase of SAR strongly depends on the anatomy. For the three models and normalization to the sum of the rung currents squared, the whole-body averaged SAR increases by up to a factor of 1.6 compared to conventional excitation and the peak spatial SAR (averaged over any 10 cm{sup 3} of tissue) by up to 13.4. For some locations the local averaged SAR goes up as much as 800 times (130 when looking only at regions where it is above 1% of the peak spatial SAR). The ratio of the peak spatial SAR to the whole-body SAR increases by a factor of up to 47 and can reach values above 800. Due to the potentially much larger power deposition, additional, preferably patient-specific, considerations are necessary to avoid injuries by such systems.

  8. Analysis of the local worst-case SAR exposure caused by an MRI multi-transmit body coil in anatomical models of the human body.

    Science.gov (United States)

    Neufeld, Esra; Gosselin, Marie-Christine; Murbach, Manuel; Christ, Andreas; Cabot, Eugenia; Kuster, Niels

    2011-08-07

    Multi-transmit coils are increasingly being employed in high-field magnetic resonance imaging, along with a growing interest in multi-transmit body coils. However, they can lead to an increase in whole-body and local specific absorption rate (SAR) compared to conventional body coils excited in circular polarization for the same total incident input power. In this study, the maximum increase of SAR for three significantly different human anatomies is investigated for a large 3 T (128 MHz) multi-transmit body coil using numerical simulations and a (generalized) eigenvalue-based approach. The results demonstrate that the increase of SAR strongly depends on the anatomy. For the three models and normalization to the sum of the rung currents squared, the whole-body averaged SAR increases by up to a factor of 1.6 compared to conventional excitation and the peak spatial SAR (averaged over any 10 cm(3) of tissue) by up to 13.4. For some locations the local averaged SAR goes up as much as 800 times (130 when looking only at regions where it is above 1% of the peak spatial SAR). The ratio of the peak spatial SAR to the whole-body SAR increases by a factor of up to 47 and can reach values above 800. Due to the potentially much larger power deposition, additional, preferably patient-specific, considerations are necessary to avoid injuries by such systems.

  9. Elementary reaction rate measurements at high temperatures by tunable-laser flash-absorption

    Energy Technology Data Exchange (ETDEWEB)

    Hessler, J.P. [Argonne National Laboratory, IL (United States)

    1993-12-01

    The major objective of this program is to measure thermal rate coefficients and branching ratios of elementary reactions. To perform these measurements, the authors constructed an ultrahigh-purity shock tube to generate temperatures between 1000 and 5500 K. The tunable-laser flash-absorption technique is used to measure the rate of change of the concentration of species which absorb below 50,000 cm{sup {minus}1} e.g.: OH, CH, and CH{sub 3}. This technique is being extended into the vacuum-ultraviolet spectral region where one can measure atomic species e.g.: H, D, C, O, and N; and diatomic species e.g.: O{sub 2}, CO, and OH.

  10. EVALUATION OF THE STRUCTURAL FUNDS ABSORPTION RATE BY MEANS OF THE HERMIN MODEL

    Directory of Open Access Journals (Sweden)

    Opritescu Elena Madalina

    2012-07-01

    Full Text Available The main objective of this article is to highlight the main method that could quantify the impact of the structural funds on the Gross Domestic Product. I also presented the regional disparities situation and the European funds absorption rate. The HERMIN model has been designed considering the evolution of macro-variables throughout transition and pre-accession process, as well as out of the need to analyze the gradual alignment of Romania’s economic policies to those of EU. The fact that, initially, the HERMIN model was designed for the European Union’s less developed economies represented the cornerstone in choosing it, as it was the case for Romania, too. However, the quantitative evaluation must always be accompanied by a qualitative evaluation, in order to comprise factors which cannot be measured by the econometrical modeling. For this purpose, when the results of econometrical model based evaluation are used, it is important to be aware of the fact that models simplify reality, no matter the impressive mathematical calculations they employ. Also, we must not omit the fact that Romania’s major development needs and the current economic context imperatively demand a high as possible level of structural funds absorption, as well as their efficient use, meant to generate a significant impact at a national, regional and local level. One of the main instruments employed to sustain economic growth, while also reducing disparities between regions is represented by the structural funds. These funds, consisting in financial contributions of the member states, according to their level of development, are redistributed in compliance with an extremely complex regulating and procedural frame, to those EU states of regions which are fallen behind from a social and economical development perspective Nevertheless, when absorption capacity of a member state is evaluated, the used percentage from the allocated funds is not the only

  11. A no-calorimetric method for measuring SAR in MRI

    Science.gov (United States)

    Romano, Rocco; Acernese, Fausto; Barone, Fabrizio

    2011-04-01

    During an MR procedure, the patient absorbs a portion of the transmitted RF energy, which may result in tissue heating and other adverse effects, such as alterations in visual, auditory and neural functions. The Specific Absorption Rate (SAR), in W/kg, is the RF power absorbed per unit mass of tissue and is one of the most important parameters related with thermal effects and acts as a guideline for MRI safety. Strict limits to the SAR levels are imposed by patient safety international regulations (CEI - EN 60601 - 2 - 33) and SAR measurements are required in order to verify its respect. The recommended methods for mean SAR measurement are quite problematic and often require a maintenance man intervention and long stop machine. For example, in the CEI recommended pulse energy method, the presence of a maintenance man is required in order to correctly connect the required instrumentation; furthermore, the procedure is complex and requires remarkable processing and calculus. Simpler are the calorimetric methods, also if in this case long acquisition times are required in order to have significant temperature variations and accurate heat capacity knowledge (CEI - EN 60601 - 2 - 33). The phase transition method is a new no-calorimetric method to measure SAR in MRI which has the advantages to be very simple and to overcome all the typical calorimetric method problems. It does not require in gantry temperature measurements, any specific heat or heat capacity knowledge, but only mass and time measurement. On the other hand, it is necessary to establish if all deposited power SAR can be considered acquired and measured. In this paper, that will be shown.

  12. The phase transition method for SAR measurement in MRI

    Science.gov (United States)

    Romano, R.; Canonico, R.; Acernese, F.; Giordano, G.; Barone, F.

    2014-03-01

    During an MR procedure, the patient absorbs a portion of the transmitted RF energy, which may result in tissue heating and other adverse effects, such as alterations in visual, auditory and neural functions. The Specific Absorption Rate (SAR), in W/kg, is the RF power absorbed per unit mass of tissue and is one of the most important parameters related with thermal effects and acts as a guideline for MRI safety. Strict limits to the SAR levels are imposed by patient safety international regulations (CEI - EN 60601 - 2 - 33) and SAR measurements are required in order to verify its respect. The recommended methods for mean SAR measurement are quite problematic and often require a maintenance man intervention and long stop machine. For example, in the CEI recommended pulse energy method, the presence of a maintenance man is required in order to correctly connect the required instrumentation; furthermore, the procedure is complex and requires remarkable processing and calculus. Simpler are the calorimetric methods, also if in this case long acquisition times are required in order to have significant temperature variations and accurate heat capacity knowledge (CEI - EN 60601 - 2 - 33). The phase transition method is a new method to measure SAR in MRI which has the advantages to be very simple and to overcome all the typical calorimetric method problems. It does not require in gantry temperature measurements, any specific heat or heat capacity knowledge, but only mass and time measurement. Nevertheless, in order to consider this method it is necessary to verify that all deposited SAR power can be considered acquired and measured. In this paper considerations about this aspect are conducted.

  13. Severe Acute Respiratory Syndrome- SARS

    Indian Academy of Sciences (India)

    SARS – clinical features · Radiological features of lungs-showing progression of disease · cT Scan of SARS lungs · Imaging type,cost,therapy · SARS – Lung Pathology · SARS Pathology · SARS - Diagnosis · How did SARS spread ? Economics of Epidemics -SARS · How was SARS contained so fast ? Slide 16 · Slide 17.

  14. Absorption of carbon dioxide and isotope exchange rate of carbon in a reaction system between carbon dioxide and carbamic acid

    International Nuclear Information System (INIS)

    Takeshita, Kenji; Kitamoto, Asashi

    1985-01-01

    The performance of isotope separation of carbon-13 by chemical exchange between carbon dioxide and carbamic acid was studied. The working fluid used in the study was a solution of DNBA, (C 4 H 9 ) 2 NH and n-octane mixture. Factors related to the isotope exchange rate were measured, such as the absorption rate of carbon dioxide into the solution of DNBA and n-octane, the isotope exchange rate and the separation factor in the reaction between CO 2 and carbamic acid. The absorption of CO 2 into the working fluid was the sum of chemical absorption by DNBA and physical absorption by n-octane. The absorption of carbon dioxide into the working fluid was negligible at temperatures over 90 0 C, but increased gradually at lower temperatures. Carbon dioxide was absorbed into DNBA by chemical absorption, and DNBA was converted to carbamic acid by the reaction. The reaction for synthesis and decomposition of carbamic acid was reversible. The separation factor in equilibrium reached a large value at lower temperatures. The isotope exchange rate between gas and liquid was proportional to the product of the concentration of carbamic acid and the concentration of CO 2 by physical absorption. The isotope separation of carbon by chemical exchange reaction is better operated under the conditions of lower temperature and higher pressure. (author)

  15. Effect of carbon dioxide on the rate of iodine vapor absorption by aqueous solution of sodium hydroxide

    International Nuclear Information System (INIS)

    Eguchi, Wataru; Adachi, Motonari; Miyake, Yoshikazu

    1978-01-01

    There is always carbon dioxide in the atmosphere as an impurity. Since this is an acid gas similar to iodine, each absorption rate seems to be affected by the other due to the coexistence of these two. Experiments have been conducted to clarify the absorption rate and absorption mechanism of iodine in the simultaneous absorption of iodine and carbon dioxide. Carbon dioxide coexisting with gas phases as an impurity decreases the absorption rate of iodine in the removal by washing with water of iodine mixed in the air. The first cause of this is that the diffusion coefficient of iodine in gas phase decreases with the carbon dioxide content in the gas phase. The second cause is that coexistent carbon dioxide is an acid gas, dissociates by dissolving into the absorbing solution, increases hydrogen ion concentration together with the formation of negative ions of bicarbonate and carbonate, and reduces hydroxyl ion concentration as a result. It is more important that existence of iodine has a catalytic effect to the rate of basic catalytic hydrolysis of carbon dioxide simultaneously dissolved in water phase, and accelerates this reaction rate. The mechanism of catalytic effect of iodine for the hydrolysis of carbon dioxide can not be clarified in detail only by this experiment, but the simultaneous absorption rate of iodine and carbon dioxide can be explained satisfactorily. (Wakatsuki, Y

  16. Decomposing DInSAR Time-Series into 3-D in Combination with GPS in the Case of Low Strain Rates: An Application to the Hyblean Plateau, Sicily, Italy

    Directory of Open Access Journals (Sweden)

    Andreas Vollrath

    2017-01-01

    Full Text Available Differential Interferometric SAR (DInSAR time-series techniques can be used to derive surface displacement rates with accuracies of 1 mm/year, by measuring the one-dimensional distance change between a satellite and the surface over time. However, the slanted direction of the measurements complicates interpretation of the signal, especially in regions that are subject to multiple deformation processes. The Simultaneous and Integrated Strain Tensor Estimation from Geodetic and Satellite Deformation Measurements (SISTEM algorithm enables decomposition into a three-dimensional velocity field through joint inversion with GNSS measurements, but has never been applied to interseismic deformation where strain rates are low. Here, we apply SISTEM for the first time to detect tectonic deformation on the Hyblean Foreland Plateau in South-East Sicily. In order to increase the signal-to-noise ratio of the DInSAR data beforehand, we reduce atmospheric InSAR noise using a weather model and combine it with a multi-directional spatial filtering technique. The resultant three-dimensional velocity field allows identification of anthropogenic, as well as tectonic deformation, with sub-centimeter accuracies in areas of sufficient GPS coverage. Our enhanced method allows for a more detailed view of ongoing deformation processes as compared to the single use of either GNSS or DInSAR only and thus is suited to improve assessments of regional seismic hazard.

  17. New constraints on slip rates and locking depths of the San Andreas Fault System from Sentinel-1A InSAR and GAGE GPS observations

    Science.gov (United States)

    Ward, L. A.; Smith-Konter, B. R.; Higa, J. T.; Xu, X.; Tong, X.; Sandwell, D. T.

    2017-12-01

    After over a decade of operation, the EarthScope (GAGE) Facility has now accumulated a wealth of GPS and InSAR data, that when successfully integrated, make it possible to image the entire San Andreas Fault System (SAFS) with unprecedented spatial coverage and resolution. Resulting surface velocity and deformation time series products provide critical boundary conditions needed for improving our understanding of how faults are loaded across a broad range of temporal and spatial scales. Moreover, our understanding of how earthquake cycle deformation is influenced by fault zone strength and crust/mantle rheology is still developing. To further study these processes, we construct a new 4D earthquake cycle model of the SAFS representing the time-dependent 3D velocity field associated with interseismic strain accumulation, co-seismic slip, and postseismic viscoelastic relaxation. This high-resolution California statewide model, spanning the Cerro Prieto fault to the south to the Maacama fault to the north, is constructed on a 500 m spaced grid and comprises variable slip and locking depths along 42 major fault segments. Secular deep slip is prescribed from the base of the locked zone to the base of the elastic plate while episodic shallow slip is prescribed from the historical earthquake record and geologic recurrence intervals. Locking depths and slip rates for all 42 fault segments are constrained by the newest GAGE Facility geodetic observations; 3169 horizontal GPS velocity measurements, combined with over 53,000 line-of-sight (LOS) InSAR velocity observations from Sentinel-1A, are used in a weighted least-squares inversion. To assess slip rate and locking depth sensitivity of a heterogeneous rheology model, we also implement variations in crustal rigidity throughout the plate boundary, assuming a coarse representation of shear modulus variability ranging from 20-40 GPa throughout the (low rigidity) Salton Trough and Basin and Range and the (high rigidity) Central

  18. Determination of Lung-to-Blood Absorption Rates for Lead and Bismuth which are Appropriate for Radon Progeny

    International Nuclear Information System (INIS)

    Marsh, J.W.; Birchall, A.

    1999-01-01

    The ICRP Publication 66 Human Respiratory Tract Model (HRTM) treats clearance as a competitive process between absorption into blood and particle transport to the gastrointestinal tract and lymphatics. The ICRP recommends default absorption rates for lead and bismuth in ICRP Publication 71 but states that the values are not appropriate for short-lived radon progeny. This paper describes an evaluation of published data from volunteer experiments to estimate the absorption half-times of lead and bismuth that are appropriate for short-lived radon progeny. The absorption half-time for lead was determined to be 10±2 h, based on 212 Pb lung and blood retention data from several studies. The absorption half-time for bismuth was estimated to be about 13 h, based on 212 Bi urinary excretion data from one experiment and the ICRP biokinetic model for bismuth as a decay product of lead. (author)

  19. Large specific absorption rates in the magnetic hyperthermia properties of metallic iron nanocubes

    Energy Technology Data Exchange (ETDEWEB)

    Mehdaoui, B.; Meffre, A.; Lacroix, L.-M. [Universite de Toulouse, INSA, UPS, LPCNO (Laboratoire de Physique et Chimie des Nano-Objets), 135 avenue de Rangueil, F-31077 Toulouse (France); CNRS, UMR 5215, LPCNO, F-31077 Toulouse (France); Carrey, J., E-mail: julian.carrey@insa-toulouse.f [Universite de Toulouse, INSA, UPS, LPCNO (Laboratoire de Physique et Chimie des Nano-Objets), 135 avenue de Rangueil, F-31077 Toulouse (France); CNRS, UMR 5215, LPCNO, F-31077 Toulouse (France); Lachaize, S. [Universite de Toulouse, INSA, UPS, LPCNO (Laboratoire de Physique et Chimie des Nano-Objets), 135 avenue de Rangueil, F-31077 Toulouse (France); CNRS, UMR 5215, LPCNO, F-31077 Toulouse (France); Gougeon, M. [Institut CARNOT-CIRIMAT-UMR 5085, Batiment 2R1, 118 route de Narbonne, F-31062 Toulouse (France); Respaud, M. [Universite de Toulouse, INSA, UPS, LPCNO (Laboratoire de Physique et Chimie des Nano-Objets), 135 avenue de Rangueil, F-31077 Toulouse (France); CNRS, UMR 5215, LPCNO, F-31077 Toulouse (France); Chaudret, B. [Laboratoire de Chimie de Coordination-CNRS, 205 rte de Narbonne, 31077 Toulouse cedex 4 (France)

    2010-10-15

    We report on the magnetic hyperthermia properties of chemically synthesized ferromagnetic 11 and 16 nm Fe(0) nanoparticles of cubic shape displaying the saturation magnetization of bulk iron. The specific absorption rate measured on 16 nm nanocubes is 1690{+-}160 W/g at 300 kHz and 66 mT. This corresponds to specific losses-per-cycle of 5.6 mJ/g, largely exceeding the ones reported in other systems. A way to quantify the degree of optimization of any system with respect to hyperthermia applications is proposed. Applied here, this method shows that our nanoparticles are not fully optimized, probably due to the strong influence of magnetic interactions on their magnetic response. Once protected from oxidation and further optimized, such nano-objects could constitute efficient magnetic cores for biomedical applications requiring very large heating power.

  20. Rating of Sound Absorption for EFBMF Acoustic Panels according to ISO 11654:1997

    Directory of Open Access Journals (Sweden)

    Samsudin Emedya Murniwaty

    2018-01-01

    Full Text Available Empty fruit bunch fibre (EFB and mesocarp fibre (MF have been used in the fabrication of a new acoustic panel as a sound absorber for building. Measurements were carried out following ISO 354 in the mini reverberation chamber and the sound absorption performance of EFBMF acoustic panels were rated based on ISO 11654. Measurements of the new EFBMF acoustic panel involves five panel designs of 100 EFB dust panels, 80:20 dust panels, 100MF coir panels, 90:10 coir panels and 50:50 coir panels with 5 cm of initial thickness. Results showed that 100MF coir panel achieved αw of 0.90 coefficient and was rated as Class A absorber followed by 90:10 coir panels with αw of 0.85 coefficient and 100 EFB dust, 80:20 dust and 50:50 coir panels having αw of 0.80 coefficients and been rated as Class B absorber. This research has successfully defined that EFB and MF are viable to be used as raw fibre for acoustic absorber for building.

  1. Geodetic SAR Tomography

    NARCIS (Netherlands)

    Zhu, Xiao Xiang; Montazeri, Sina; Gisinger, Christoph; Hanssen, R.F.; Bamler, Richard

    2016-01-01

    In this paper, we propose a framework referred to as 'geodetic synthetic aperture radar (SAR) tomography' that fuses the SAR imaging geodesy and tomographic SAR inversion (TomoSAR) approaches to obtain absolute 3-D positions of a large amount of natural scatterers. The methodology is applied on

  2. Activable enriched stable isotope iron-58 for monitoring absorption rate of juvenile athletes for iron: a case study.

    Science.gov (United States)

    Qian, Qinfang; Chai, Zhifang; Feng, Weiyu; Chen, Jidi; Zhang, Peiqun; Pan, Jianxiang

    2002-09-01

    Activable enriched stable isotopes can play a unique role in studies of nutritional status, metabolism, absorption rates, and bioavailability of minerals. As a practical example, eight juvenile athletes were selected to test the absorption rates of iron during training and non-training periods by enriched stable isotope of Fe-58 (enriched degree: 51.1%) via activation analysis Fe-58 (n, gamma) Fe-59 of the collected feces samples. The results indicated that the average iron absorption rates of the juvenile athletes with and without training are 9.1 +/- 2.8 and 11.9 +/- 4.7%, respectively, which implies that the long-term endurance training with high intensity makes the iron absorption rate of athletes lower. In the meantime, the comparison of the activable enriched isotope technique with atomic absorption spectrometry was performed, which showed that the former was better than the latter in reliability and sensitivity. It is because this nuclear method can distinguish the exogenous and endogenous iron in the samples, but not for non-nuclear methods.

  3. Effect of dipolar interactions and DC magnetic field on the specific absorption rate of an array of magnetic nanoparticles

    Science.gov (United States)

    Déjardin, J.-L.; Vernay, F.; Respaud, M.; Kachkachi, H.

    2017-05-01

    We address the issue of inter-particle dipolar interactions in the context of magnetic hyperthermia. More precisely, the main question dealt with here is concerned with the conditions under which the specific absorption rate is enhanced or reduced by dipolar interactions. For this purpose, we propose a theory for the calculation of the AC susceptibility, and thereby the specific absorption rate, for a monodisperse two-dimensional assembly of nanoparticles with oriented anisotropy, in the presence of a DC magnetic field, in addition to the AC magnetic field. We also study the competition between the dipolar interactions and the DC field, both in the transverse and longitudinal configurations. In both cases, we find that the specific absorption rate has a maximum at some critical DC field that depends on the inter-particle separation. In the longitudinal setup, this critical field falls well within the range of experiments.

  4. Potential chlorofluorocarbon replacements: OH reaction rate constants between 250 and 315 K and infrared absorption spectra

    Science.gov (United States)

    Garland, Nancy L.; Medhurst, Laura J.; Nelson, H. H.

    1993-12-01

    We measured the rate constant for reactions of the OH radical with several potential chlorofluorocarbon replacements over the temperature range 251-314 K using laser photolysis laser-induced fluorescence techniques. The compounds studied and Arrhenius parameters determined from fits to the measured rate constants are as follows: CHF2OCHF2 (E 134), k(T) = (5.4 ± 3.5) × 10-13 cm3 s-1 exp [(-3.1 ± 0.4 kcal mol-1)/RT]; CF3CH2CF3 (FC 236fa), k(T) = (2.0 ± 1.0) × 10-14 cm3 s-1 exp [(-1.8 ± 0.3 kcal mol-1)/RT]; CF3CHFCHF2 (FC 236ea), k(T) = (2.0 ± 0.9) × 10-13 cm3 s-1 exp [(-2.0 ± 0.3 kcal mol-1)/RT]; and CF3CF2CH2F (FC 236cb), k(T)= (2.6 ± 1.6) × 10-13 cm3 s-1 exp [(-2.2 ± 0.4 kcal mol-1)/RT]. The measured activation energies (2-3 kcal mol-1) are consistent with a mechanism of H atom abstraction. The tropospheric lifetimes, estimated from the measured OH reaction rates, and measured integrated infrared absorption cross sections over the range 770 to 1430 cm-1 suggest that E 134 and FC 236fa may have significant global warming potential, while FC 236ea and FC 236cb do not.

  5. Study of the influence of the laterality of mobile phone use on the SAR induced in two head models

    Science.gov (United States)

    Ghanmi, Amal; Varsier, Nadège; Hadjem, Abdelhamid; Conil, Emmanuelle; Picon, Odile; Wiart, Joe

    2013-05-01

    The objective of this paper is to investigate and to analyse the influence of the laterality of mobile phone use on the exposure of the brain to radio-frequencies (RF) and electromagnetic fields (EMF) from different mobile phone models using the finite-difference time-domain (FDTD) method. The study focuses on the comparison of the specific absorption rate (SAR) induced on the right and left sides of two numerical adult and child head models. The heads are exposed by both phone models operating in GSM frequency bands for both ipsilateral and contralateral configurations. A slight SAR difference between the two sides of the heads is noted. The results show that the variation between the left and the right sides is more important at 1800 MHz for an ipsilateral use. Indeed, at this frequency, the variation can even reach 20% for the SAR10g and the SAR1g induced in the head and in the brain, respectively. Moreover, the average SAR induced by the mobile phone in the half hemisphere of the brain in ipsilateral exposure is higher than in contralateral exposure. Owing to the superficial character of energy deposition at 1800 MHz, this difference in the SAR induced for the ipsilateral and contralateral usages is more significant at 1800 MHz than at 900 MHz. The results have shown that depending on the phantom head models, the SAR distribution in the brain can vary because of differences in anatomical proportions and in the geometry of the head models. The induced SAR in child head and in sub-regions of the brain is significantly higher (up to 30%) compared to the adult head. This paper confirms also that the shape/design of the mobile and the location of the antenna can have a large influence at high frequency on the exposure of the brain, particularly on the SAR distribution and on the distinguished brain regions.

  6. The effect of sewage sludge application on the growth and absorption rates of Pb and As in water spinach

    Directory of Open Access Journals (Sweden)

    Rong Wang

    2016-01-01

    Full Text Available This paper investigated the effect of the application of sewage sludge on the growth rates and absorption rates of Pb and As in potted water spinach. Our results indicated that application of sewage sludge promoted vegetable growth, and the dry weight of water spinach reached a maximal value (4.38 ± 0.82 g upon 8% sludge application. We also found that the dry weights of water spinach after treatment were all greater than those of the control systems (CK. Treatment with sludge promoted the absorption of Pb and As in water spinach, with a significant (p < 0.05 increase of absorbed Pb following treatment concentrations above 10%, and a peak absorption of As at 8%. Finally, we found that concentrations of Pb and As were higher in rhizosphere-attached soil than in free pot.

  7. Fall transport - A study to compare smolt-to-adult return rates (SARs) of Snake River fall Chinook salmon under alternative transport and dam operational strategies

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This U.S. Army Corps of Engineers (USACE)-funded study that began in 2005 compares the SARs of PIT tagged juvenile hatchery Snake River fall Chinook that are split...

  8. Latest Rate, Extent, and Temporal Evolution of Growth Faulting over Greater Houston Region Revealed by Multi- Band InSAR Time-Series Analysis

    Science.gov (United States)

    Qu, F.; Lu, Z.; Kim, J. W.

    2017-12-01

    Growth faults are common and continue to evolve throughout the unconsolidated sediments of Greater Houston (GH) region in Texas. Presence of faults can induce localized surface displacements, aggravate localized subsidence, and discontinue the integrity of ground water flow. Property damages due to fault creep have become more evident during the past few years over the GH area, portraying the necessity of further study of these faults. Interferometric synthetic aperture radar (InSAR) has been proven to be effective in mapping creep along and/or across faults. However, extracting a short wavelength, as well as small amplitude of the creep signal (about 10-20 mm/year) from long time span interferograms is extremely difficult, especially in agricultural or vegetated areas. This paper aims to map and monitor the latest rate, extent, and temporal evolution of faulting at a highest spatial density over GH region using an improved Multi-temporal InSAR (MTI) technique. The method, with maximized usable signal and correlation, has the ability to identify and monitor the active faults to provide an accurate and elaborate image of the faults. In this study, two neighboring ALOS tracks and Sentinel-1A datasets are used. Many zones of steep phase gradients and/or discontinuities have been recognized from the long term velocity maps by both ALOS (2007-2011) and Sentinei-1A (2015-2017) imagery. Not only those previously known faults position but also the new fault traces that have not been mapped by other techniques are imaged by our MTI technique. Fault damage and visible cracking of ground were evident at most locations through our field survey. The discovery of new fault activation, or faults moved from earlier locations is a part of the Big Barn Fault and Conroe fault system, trending from southwest to northeast between Hockley and Conroe. The location of area of subsidence over GH is also shrinking and migrating toward the northeast (Montgomery County) after 2000. The

  9. Near-source high-rate GPS, strong motion and InSAR observations to image the 2015 Lefkada (Greece) Earthquake rupture history.

    Science.gov (United States)

    Avallone, Antonio; Cirella, Antonella; Cheloni, Daniele; Tolomei, Cristiano; Theodoulidis, Nikos; Piatanesi, Alessio; Briole, Pierre; Ganas, Athanassios

    2017-09-04

    The 2015/11/17 Lefkada (Greece) earthquake ruptured a segment of the Cephalonia Transform Fault (CTF) where probably the penultimate major event was in 1948. Using near-source strong motion and high sampling rate GPS data and Sentinel-1A SAR images on two tracks, we performed the inversion for the geometry, slip distribution and rupture history of the causative fault with a three-step self-consistent procedure, in which every step provided input parameters for the next one. Our preferred model results in a ~70° ESE-dipping and ~13° N-striking fault plane, with a strike-slip mechanism (rake ~169°) in agreement with the CTF tectonic regime. This model shows a bilateral propagation spanning ~9 s with the activation of three main slip patches, characterized by rise time and peak slip velocity in the ranges 2.5-3.5 s and 1.4-2.4 m/s, respectively, corresponding to 1.2-1.8 m of slip which is mainly concentrated in the shallower ( 6) earthquakes to the northern and to the southern boundaries of the 2015 causative fault cannot be excluded.

  10. Changes in ruminal volatile fatty acid production and absorption rate during the dry period and early lactation as affected by rate of increase of concentrate allowance

    NARCIS (Netherlands)

    Dieho, K.|info:eu-repo/dai/nl/314000550; Dijkstra, J.; Schonewille, J. T.|info:eu-repo/dai/nl/185364306; Bannink, A.

    The aim of the present experiment was to study changes in volatile fatty acid (VFA) production using an isotope dilution technique, and changes in VFA fractional absorption rate (k aVFA) using a buffer incubation technique (BIT) during the dry period and early lactation, as affected by the

  11. Whole-body and local RF absorption in human models as a function of anatomy and position within 1.5T MR body coil.

    Science.gov (United States)

    Murbach, Manuel; Neufeld, Esra; Kainz, Wolfgang; Pruessmann, Klaas P; Kuster, Niels

    2014-02-01

    Radiofrequency energy deposition in magnetic resonance imaging must be limited to prevent excessive heating of the patient. Correlations of radiofrequency absorption with large-scale anatomical features (e.g., height) are investigated in this article. The specific absorption rate (SAR), as the pivotal parameter for quantifying absorbed radiofrequency, increases with the radial dimension of the patient and therefore with the large-scale anatomical properties. The absorbed energy in six human models has been modeled in different Z-positions (head to knees) within a 1.5T bodycoil. For a fixed B1+ incident field, the whole-body SAR can be up to 2.5 times higher (local SAR up to seven times) in obese adult models compared to children. If the exposure is normalized to 4 W/kg whole-body SAR, the local SAR can well-exceed the limits for local transmit coils and shows intersubject variations of up to a factor of three. The correlations between anatomy and induced local SAR are weak for normalized exposure, but strong for a fixed B1+ field, suggesting that anatomical properties could be used for fast SAR predictions. This study demonstrates that a representative virtual human population is indispensable for the investigation of local SAR levels. Copyright © 2013 Wiley Periodicals, Inc.

  12. SAR in a child voxel phantom from exposure to wireless computer networks (Wi-Fi).

    Science.gov (United States)

    Findlay, R P; Dimbylow, P J

    2010-08-07

    Specific energy absorption rate (SAR) values have been calculated in a 10 year old sitting voxel model from exposure to electromagnetic fields at 2.4 and 5 GHz, frequencies commonly used by Wi-Fi devices. Both plane-wave exposure of the model and irradiation from antennas in the near field were investigated for a variety of exposure conditions. In all situations studied, the SAR values calculated were considerably below basic restrictions. For a typical Wi-Fi exposure scenario using an inverted F antenna operating at 100 mW, a duty factor of 0.1 and an antenna-body separation of 34 cm, the maximum peak localized SAR was found to be 3.99 mW kg(-1) in the torso region. At 2.4 GHz, using a power of 100 mW and a duty factor of 1, the highest localized SAR value in the head was calculated as 5.7 mW kg(-1). This represents less than 1% of the SAR previously calculated in the head for a typical mobile phone exposure condition.

  13. SAR exposure from UHF RFID reader in adult, child, pregnant woman, and fetus anatomical models.

    Science.gov (United States)

    Fiocchi, Serena; Markakis, Ioannis A; Ravazzani, Paolo; Samaras, Theodoros

    2013-09-01

    The spread of radio frequency identification (RFID) devices in ubiquitous applications without their simultaneous exposure assessment could give rise to public concerns about their potential adverse health effects. Among the various RFID system categories, the ultra high frequency (UHF) RFID systems have recently started to be widely used in many applications. This study addresses a computational exposure assessment of the electromagnetic radiation generated by a realistic UHF RFID reader, quantifying the exposure levels in different exposure scenarios and subjects (two adults, four children, and two anatomical models of women 7 and 9 months pregnant). The results of the computations are presented in terms of the whole-body and peak spatial specific absorption rate (SAR) averaged over 10 g of tissue to allow comparison with the basic restrictions of the exposure guidelines. The SAR levels in the adults and children were below 0.02 and 0.8 W/kg in whole-body SAR and maximum peak SAR levels, respectively, for all tested positions of the antenna. On the contrary, exposure of pregnant women and fetuses resulted in maximum peak SAR(10 g) values close to the values suggested by the guidelines (2 W/kg) in some of the exposure scenarios with the antenna positioned in front of the abdomen and with a 100% duty cycle and 1 W radiated power. Copyright © 2013 Wiley Periodicals, Inc.

  14. An open-ended waveguide system for SAR system validation or probe calibration for frequencies above 3 GHz

    International Nuclear Information System (INIS)

    Li Qingxiang; Gandhi, Om P; Kang Gang

    2004-01-01

    Compliance with safety guidelines prescribed in terms of maximum electromagnetic power absorption (specific absorption rate or SAR) for any 1- or 10-g of tissue is required for all newly introduced personal wireless devices such as wireless PCs. The prescribed SAR measuring system is a planar phantom with a relatively thin base of thickness 2.0 mm filled with a lossy fluid to simulate dielectric properties of the tissues. A well-characterized, broadband irradiator is required for SAR system validation or submerged E-field probe calibration for the Wi-Fi frequencies in the 5-6 GHz band. We describe an open-ended waveguide system that may be used for this purpose. Using a fourth-order polynomial least-squares fit to the experimental data gives SAR variations close to the bottom surface of the phantom that are in excellent agreement with those obtained using the finite-difference time-domain (FDTD) numerical method. The experimentally determined peak 1- and 10-g SARs are within 1 to 2% of those obtained using the FDTD both at 5.25 and 5.8 GHz

  15. Effect of Feed Gas Flow Rate on CO2 Absorption through Super Hydrophobic Hollow Fiber membrane Contactor

    Science.gov (United States)

    Kartohardjono, Sutrasno; Alexander, Kevin; Larasati, Annisa; Sihombing, Ivander Christian

    2018-03-01

    Carbon dioxide is pollutant in natural gas that could reduce the heating value of the natural gas and cause problem in transportation due to corrosive to the pipeline. This study aims to evaluate the effects of feed gas flow rate on CO2 absorption through super hydrophobic hollow fiber contactor. Polyethyleneglycol-300 (PEG-300) solution was used as absorbent in this study, whilst the feed gas used in the experiment was a mixture of 30% CO2 and 70% CH4. There are three super hydrophobic hollow fiber contactors sized 6 cm and 25 cm in diameter and length used in this study, which consists of 1000, 3000 and 5000 fibers, respectively. The super hydrophobic fiber membrane used is polypropylene-based with outer and inner diameter of about 525 and 235 μm, respectively. In the experiments, the feed gas was sent through the shell side of the membrane contactor, whilst the absorbent solution was pumped through the lumen fibers. The experimental results showed that the mass transfer coefficient, flux, absorption efficiency for CO2-N2 system and CO2 loading increased with the feed gas flow rate, but the absorption efficiency for CO2-N2 system decreased. The mass transfer coefficient and the flux, at the same feed gas flow rate, decreased with the number of fibers in the membrane contactor, but the CO2 absorption efficiency and the CO2 loading increased.

  16. The rate of intestinal glucose absorption is correlated with plasma glucose-dependent insulinotropic polypeptide concentrations in healthy men

    DEFF Research Database (Denmark)

    Wachters-Hagedoorn, Renate E; Priebe, Marion G; Heimweg, Janneke A J

    2006-01-01

    of the factors determining the metabolic quality of different types of carbohydrates. We analyzed the correlation between the rate of intestinal absorption of (starch-derived) glucose and plasma concentrations of GLP-1 and GIP after ingestion of glucose and starchy foods with a different content of rapidly...... and slowly available glucose. In a crossover study, glucose, insulin, GLP-1, and GIP concentrations were monitored for 6 h after consumption of glucose, uncooked cornstarch (UCCS) or corn pasta in 7 healthy men. All test meals were naturally labeled with 13C. Using a primed, continuous D-[6,6-2H2]glucose...... infusion, the rate of appearance of exogenous glucose (RaEx) was estimated, reflecting the rate of intestinal glucose absorption. GLP-1 concentrations increased significantly from 180 to 300 min after ingestion of UCCS, the starch product with a high content of slowly available glucose. A high GIP response...

  17. FDTD calculation of whole-body average SAR in adult and child models for frequencies from 30 MHz to 3 GHz

    International Nuclear Information System (INIS)

    Wang Jianqing; Fujiwara, Osamu; Kodera, Sachiko; Watanabe, Soichi

    2006-01-01

    Due to the difficulty of the specific absorption rate (SAR) measurement in an actual human body for electromagnetic radio-frequency (RF) exposure, in various compliance assessment procedures the incident electric field or power density is being used as a reference level, which should never yield a larger whole-body average SAR than the basic safety limit. The relationship between the reference level and the whole-body average SAR, however, was established mainly based on numerical calculations for highly simplified human modelling dozens of years ago. Its validity is being questioned by the latest calculation results. In verifying the validity of the reference level with respect to the basic SAR limit for RF exposure, it is essential to have a high accuracy of human modelling and numerical code. In this study, we made a detailed error analysis in the whole-body average SAR calculation for the finite-difference time-domain (FDTD) method in conjunction with the perfectly matched layer (PML) absorbing boundaries. We derived a basic rule for the PML employment based on a dielectric sphere and the Mie theory solution. We then attempted to clarify to what extent the whole-body average SAR may reach using an anatomically based Japanese adult model and a scaled child model. The results show that the whole-body average SAR under the ICNIRP reference level exceeds the basic safety limit nearly 30% for the child model both in the resonance frequency and 2 GHz band

  18. FDTD calculation of whole-body average SAR in adult and child models for frequencies from 30 MHz to 3 GHz.

    Science.gov (United States)

    Wang, Jianqing; Fujiwara, Osamu; Kodera, Sachiko; Watanabe, Soichi

    2006-09-07

    Due to the difficulty of the specific absorption rate (SAR) measurement in an actual human body for electromagnetic radio-frequency (RF) exposure, in various compliance assessment procedures the incident electric field or power density is being used as a reference level, which should never yield a larger whole-body average SAR than the basic safety limit. The relationship between the reference level and the whole-body average SAR, however, was established mainly based on numerical calculations for highly simplified human modelling dozens of years ago. Its validity is being questioned by the latest calculation results. In verifying the validity of the reference level with respect to the basic SAR limit for RF exposure, it is essential to have a high accuracy of human modelling and numerical code. In this study, we made a detailed error analysis in the whole-body average SAR calculation for the finite-difference time-domain (FDTD) method in conjunction with the perfectly matched layer (PML) absorbing boundaries. We derived a basic rule for the PML employment based on a dielectric sphere and the Mie theory solution. We then attempted to clarify to what extent the whole-body average SAR may reach using an anatomically based Japanese adult model and a scaled child model. The results show that the whole-body average SAR under the ICNIRP reference level exceeds the basic safety limit nearly 30% for the child model both in the resonance frequency and 2 GHz band.

  19. Survey on Different Samsung with Nokia Smart Mobile Phones in the Specific Absorption Rate Electrical Field of Head.

    Science.gov (United States)

    Fakhri, Yadolah; Alinejad, Azim; Keramati, Hassan; Bay, Abotaleb; Avazpour, Moayed; Zandsalimi, Yahya; Moradi, Bigard; Rasouli Amirhajeloo, Leila; Mirzaei, Maryam

    2016-09-01

    The use of smart phones is increasing in the world. This excessive use, especially in the last two decades, has created too much concern on the effects of emitted electromagnetic fields and specific absorption rate on human health. In this descriptive-analytical study of the electric field resulting from smart phones of Samsung and Nokia by portable measuring device, electromagnetic field, Model HI-3603-VDT/VLF, were measured. Then, head absorption rate was calculated in these two mobiles by ICNIRP equation. Finally, the comparison of specific absorption rate, especially between Samsung and Nokia smart phones, was conducted by T-Test statistics analysis. The mean of electric field for Samsung and Nokia smart mobile phones was obtained 1.8 ±0.19 v/m  and 2.23±0.39 v/m , respectively, while the range of the electric field was obtained as 1.56-2.21 v/m and 1.69-2.89 v/m for them, respectively. The mean of specific absorption rate in Samsung and Nokia was obtained 0.002 ± 0.0005 W/Kg and 0.0041±0.0013 W/Kg at the frequency of 900 MHz and 0.004±0.001 W/Kg and 0.0062±0.0002 W/Kg at the frequency of 1800 MHz respectively. The ratio of mean electronic field to guidance in the Samsung mobile phone at the frequency of 900 MHz and 1800 MHz was 4.36% and 3.34%, while was 5.62% and 4.31% in the Nokia mobile phone, respectively. The ratio of mean head specific absorption rate in smart mobile phones of Samsung and Nokia in the guidance level at the frequency of 900 was 0.15% and 0.25%, respectively, while was 0.23 %and 0.38% at the frequency of 1800 MHz, respectively. The rate of specific absorption of Nokia smart  mobile phones at the frequencies of 900 and 1800 MHz  was significantly higher than Samsung (p value Samsung smart mobile phone.

  20. 4G antennas for wireless eyewear devices and related SAR

    Science.gov (United States)

    Cihangir, Aykut; Whittow, Will; Panagamuwa, Chinthana; Jacquemod, Gilles; Gianesello, Frédéric; Luxey, Cyril

    2015-11-01

    In this paper, we first present a feasibility study to design 4G antennas (700-960 MHz and 1.7-2.7 GHz) for eyewear devices. Those eyewear devices should be connected to the last generation cellular networks, Wireless Local Area Networks or wireless hotspots. Three coupling element type antennas with their matching networks are evaluated in terms of reflection coefficient and total radiation efficiency when the eyewear is placed on the user's head. We also present Specific Absorption Rate (SAR) simulations when the eyewear is positioned over a homogeneous SAM phantom and over a heterogeneous VH (Visible Human) phantom: the SAR levels are compared to international limit values. In a second step, we present experimental results obtained with 3D printed eyewear and coupling elements etched on a classical PCB substrate where the matching circuits are optimized close to the feeding point of the coupling element. Simulated and measured values are in very good agreement: 7 to 16% and 9 to 35% total efficiency are respectively obtained for the low- and high-frequency bands. However, simulated SAR values are somewhat higher than authorized levels with preoccupant high electromagnetic field distribution close to the eye of the user.

  1. Abnormal oral glucose tolerance and glucose malabsorption after vagotomy and pyloroplasty. A tracer method for measuring glucose absorption rates

    International Nuclear Information System (INIS)

    Radziuk, J.; Bondy, D.C.

    1982-01-01

    The mechanisms underlying the abnormal glucose tolerance in patients who had undergone vagotomy and pyloroplasty were investigated by measuring the rates of absorption of ingested glucose and the clearance rate of glucose using tracer methods. These methods are based on labeling a 100-g oral glucose load with [1- 14 C]glucose and measuring glucose clearance using plasma levels of infused [3- 3 H]glucose. The rate of appearance of both ingested and total glucose is then calculated continuously using a two-compartment model of glucose kinetics. It was found that about 30% of the ingested glucose (100 g) failed to appear in the systemic circulation. That this was due to malabsorption was confirmed using breath-hydrogen analysis. The absorption period is short (101 +/- 11 min) compared with normal values but the clearance of glucose is identical to that in control subjects, and it peaks 132 +/- 7 min after glucose loading. The peak plasma insulin values were more than four times higher in patients than in normal subjects, and this may afford an explanation of rates of glucose clearance that are inappropriate for the short absorption period. The combination of glucose malabsorption and this clearance pattern could yield the hypoglycemia that may be observed in patients after gastric surgery

  2. Calculations of Solar Shortwave Heating Rates due to Black Carbon and Ozone Absorption Using in Situ Measurements

    Science.gov (United States)

    Gao, R. S.; Hall, S. R.; Swartz, W. H.; Spackman, J. R.; Watts, L. A.; Fahey, D. W.; Aikin, K. C.; Shetter, R. E.; Bui, T. P.

    2008-01-01

    Results for the solar heating rates in ambient air due to absorption by black-carbon (BC) containing particles and ozone are presented as calculated from airborne observations made in the tropical tropopause layer (TTL) in January-February 2006. The method uses airborne in situ observations of BC particles, ozone and actinic flux. Total BC mass is obtained along the flight track by summing the masses of individually detected BC particles in the range 90 to 600-nm volume-equivalent diameter, which includes most of the BC mass. Ozone mixing ratios and upwelling and partial downwelling solar actinic fluxes were measured concurrently with BC mass. Two estimates used for the BC wavelength-dependent absorption cross section yielded similar heating rates. For mean altitudes of 16.5, 17.5, and 18.5 km (0.5 km) in the tropics, average BC heating rates were near 0.0002 K/d. Observed BC coatings on individual particles approximately double derived BC heating rates. Ozone heating rates exceeded BC heating rates by approximately a factor of 100 on average and at least a factor of 4, suggesting that BC heating rates in this region are negligible in comparison.

  3. Synthesis and antibody conjugation of magnetic nanoparticles with improved specific power absorption rates for alternating magnetic field cancer therapy

    International Nuclear Information System (INIS)

    Gruettner, Cordula; Mueller, Knut; Teller, Joachim; Westphal, Fritz; Foreman, Allan; Ivkov, Robert

    2007-01-01

    Bionized nanoferrite (BNF) particles with high specific power absorption rates were synthesized in the size range of 20-100 nm by high-pressure homogenization for targeted cancer therapy with alternating magnetic fields. Several strategies were used to conjugate antibodies to the BNF particles. These strategies were compared using an immunoassay to find optimal conditions to reach a high immunoreactivity of the final antibody-particle conjugate

  4. Comparison Nokia, Samsung and Sony mobile phones in the specific absorption rate of head induced to electric field

    Directory of Open Access Journals (Sweden)

    Yadolah Fakhri

    2016-07-01

    Full Text Available The use of mobile phones has expanded in recent decades. Despite the extensive studies in this field, less attention has been paid to the biological effects of electromagnetic fields emitted by the mobile phones. Therefore, in this study there has been an attempt to compare the electric field, the specific absorption rate caused by exposure to mobile phones from samsung, nokia and sony to be followed. The electric field of Samsung mobile phones (8 Brands, Nokia (9 Brands and Sony (4 Brands at intervals of 2, 25 and 50 cm in case of ringing, vibration and silent modes by HI-3603 equipment to measure and compare. The electric field amplitude Brand Samsung 0.06 to 1.5 v/m in Nokia brand 0.06 to 10.9 v/m, 0.05 to 2.8 v/m in the Sony brand. Specific absorption rate respectively in different modes Samsung brand; vibration 0.05. Although the electric field, followed by specific absorption rate was significantly less than standard, many dangers of mobile phone use is unknown, therefore their use should be taken with caution.

  5. Severe Acute Respiratory Syndrome- SARS

    Indian Academy of Sciences (India)

    Table of contents. Severe Acute Respiratory Syndrome- SARS · PowerPoint Presentation · Slide 3 · Global pattern of SARS epidemic · Slide 5 · SARS – clinical features · Radiological features of lungs-showing progression of disease · cT Scan of SARS lungs · Imaging type,cost,therapy · SARS – Lung Pathology.

  6. Operation of a low temperature absorption chiller at rating point and at reduced evaporator temperature

    Science.gov (United States)

    Best, R.; Biermann, W.; Reimann, R. C.

    1985-01-01

    The returned fifteen ton Solar Absorption Machine (SAM) 015 chiller was given a cursory visual inspection, some obvious problems were remedied, and then it was placed on a test stand to get a measure of dirty performance. It was then given a standard acid clean, the water side of the tubes was brushed clean, and then the machine was retested. The before and after cleaning data were compared to equivalent data taken before the machine was shipped. The second part of the work statement was to experimentally demonstrate the technical feasibility of operating the chiller at evaporator temperatures below 0(0)C (32(0)F) and identify any operational problems.

  7. Variable food absorption by Antarctic krill: Relationships between diet, egestion rate and the composition and sinking rates of their fecal pellets

    Science.gov (United States)

    Atkinson, A.; Schmidt, K.; Fielding, S.; Kawaguchi, S.; Geissler, P. A.

    2012-01-01

    The kinetics of food processing by zooplankton affects both their energy budgets and the biogeochemical fate of their fecal pellets. We sampled 40 schools of krill across the Scotia Sea during spring, summer and autumn and found that in all 3 seasons, every aspect of their absorption and defecation varied greatly. The C content of fecal pellets varied from 0.85% to 29% of their dry mass (median 9.8%) and C egestion rates varied 75-fold. C:N mass ratios of pellets ranged from 4.9 to 13.2 (median 7.8), higher than values of 3.9 in the krill and 5.4 in their food, pointing to enhanced uptake of N. Pellet sinking rates equated to 27-1218 m d -1 (median 304 m d -1), being governed mainly by pellet diameter (80-600 μm, mean 183 μm) and density (1.038-1.391 g cm -3, mean 1.121 g cm -3). Pellets showed little loss of C or N in filtered seawater over the first 2 days and were physically robust. When feeding rates were low, slow gut passage time and high absorption efficiency resulted in low egestion rates of pellets that were low in C and N content. These pellets were compact, dense and fast-sinking. Conversely, in good feeding conditions much food tended to pass quickly through the gut and was not efficiently absorbed, producing C and N-rich, slow-sinking pellets. Such "superfluous feeding" probably maximises the absolute rates of nutrient absorption. Food composition was also important: diatom-rich diets depressed the C content of the pellets but increased their sinking rates, likely due to silica ballasting. So depending on how krill process food, their pellets could represent both vehicles for rapid export and slow sinking, C and N-rich food sources for pelagic scavengers. C egestion rates by krill averaged 3.4% of summer primary production (and ingestion rates would be 2-10-fold higher than this) so whatever the fate of the pellets, krill are an important re-packager within the food web. While salp pellets tend to sink faster than those of krill, it is the latter

  8. Simplified segmented human models for whole body and localised SAR evaluation of 20 MHz to 6 GHz electromagnetic field exposures.

    Science.gov (United States)

    Wu, Tongning; Shao, Qing; Yang, Lei

    2013-03-01

    The digital human model is a key element in evaluating the electromagnetic field (EMF) exposure. This paper proposes the application of simplified segmented human models for EMF exposure compliance evaluation with the whole body and the localised limits. The method is based on the fact that most of the EMF power absorption is concentrated in several major tissues. Two kinds of human models were simply (the proposed method) and precisely segmented from two sets of whole body magnetic resonance imaging (MRI) scanned images. The whole body average-specific absorption rate (WBA-SAR) and the peak localised SAR averaging over 10 g tissues for the two kinds of models are calculated for various exposure configurations. The results confirmed the efficiency and the validity of the proposed method. The application as evaluating the MRI radiofrequency EMF exposure is also discussed in the paper.

  9. Simplified segmented human models for whole body and localised SAR evaluation of 20 MHz to 6 GHz electromagnetic field exposures

    International Nuclear Information System (INIS)

    Wu, T.; Shao, Q.; Yang, L.

    2013-01-01

    The digital human model is a key element in evaluating the electromagnetic field (EMF) exposure. This paper proposes the application of simplified segmented human models for EMF exposure compliance evaluation with the whole body and the localised limits. The method is based on the fact that most of the EMF power absorption is concentrated in several major tissues. Two kinds of human models were simply (the proposed method) and precisely segmented from two sets of whole body magnetic resonance imaging (MRI) scanned images. The whole body average-specific absorption rate (WBA-SAR) and the peak localised SAR averaging over 10 g tissues for the two kinds of models are calculated for various exposure configurations. The results confirmed the efficiency and the validity of the proposed method. The application as evaluating the MRI radiofrequency EMF exposure is also discussed in the paper. (authors)

  10. MicroCT image-generated tumour geometry and SAR distribution for tumour temperature elevation simulations in magnetic nanoparticle hyperthermia.

    Science.gov (United States)

    Lebrun, Alexander; Manuchehrabadi, Navid; Attaluri, Anilchandra; Wang, Frank; Ma, Ronghui; Zhu, Liang

    2013-12-01

    The objective of this study was to develop and test computer algorithms to export micro computed tomography (microCT) images and to generate tumour geometry and specific absorption rate (SAR) distribution for heat transfer simulation in magnetic nanoparticle hyperthermia. Computer algorithms were written to analyse and export microCT images of 3D tumours containing magnetic nanoparticles. MATLAB(®) and ProE(®) programs were used to generate a prototype of the tumour geometry. The enhancements in the microCT pixel index number due to presence of nanoparticles in the tumours were first converted into corresponding SAR values. The SAR data were then averaged over three-dimensional clusters of pixels using the SAS(®) program. This greatly decreased the size of the SAR file, while in the meantime it ensured that the amount of total energy deposited in the tumour was conserved. Both the tumour geometry and the SAR file were then imported into the COMSOL(®) software package to simulate temperature elevations in the tumour and their surrounding tissue region during magnetic nanoparticle hyperthermia. A linear relationship was obtained to relate individual pixel index numbers in the microCT images to the SAR values under a specific magnetic field. The generated prototype of the tumour geometry based on only 30 slices of microCT images resembled the original tumour shape and size. The tumour geometry and the simplified SAR data set were successfully accepted by the COMSOL software for heat transfer simulation. Up to 20 °C temperature elevations from its baseline temperature were found inside the tumours, implying possible thermal damage to the tumour during magnetic nanoparticle hyperthermia.

  11. The estimation of 3D SAR distributions in the human head from mobile phone compliance testing data for epidemiological studies

    International Nuclear Information System (INIS)

    Wake, Kanako; Watanabe, Soichi; Taki, Masao; Varsier, Nadege; Wiart, Joe; Mann, Simon; Deltour, Isabelle; Cardis, Elisabeth

    2009-01-01

    A worldwide epidemiological study called 'INTERPHONE' has been conducted to estimate the hypothetical relationship between brain tumors and mobile phone use. In this study, we proposed a method to estimate 3D distribution of the specific absorption rate (SAR) in the human head due to mobile phone use to provide the exposure gradient for epidemiological studies. 3D SAR distributions due to exposure to an electromagnetic field from mobile phones are estimated from mobile phone compliance testing data for actual devices. The data for compliance testing are measured only on the surface in the region near the device and in a small 3D region around the maximum on the surface in a homogeneous phantom with a specific shape. The method includes an interpolation/extrapolation and a head shape conversion. With the interpolation/extrapolation, SAR distributions in the whole head are estimated from the limited measured data. 3D SAR distributions in the numerical head models, where the tumor location is identified in the epidemiological studies, are obtained from measured SAR data with the head shape conversion by projection. Validation of the proposed method was performed experimentally and numerically. It was confirmed that the proposed method provided good estimation of 3D SAR distribution in the head, especially in the brain, which is the tissue of major interest in epidemiological studies. We conclude that it is possible to estimate 3D SAR distributions in a realistic head model from the data obtained by compliance testing measurements to provide a measure for the exposure gradient in specific locations of the brain for the purpose of exposure assessment in epidemiological studies. The proposed method has been used in several studies in the INTERPHONE.

  12. The corrosion rate and the hydrogen absorption behavior of titanium under reducing condition-III. Research document

    International Nuclear Information System (INIS)

    Suzuki, H.; Taniguchi, N.; Kawakami, S.

    2005-03-01

    Titanium is one of the candidate materials for overpacks as a high corrosion resistance metal. At the initial stage of repository, oxidizing condition will be given around the overpack because oxygen will be brought from the ground. The oxygen will be consumed by the reaction with impurities in buffer material or corrosion of overpack, and reducing condition will be achieved around the overpack. With the changing of redox condition, the water reduction becomes to dominate the cathodic reaction accompanying hydrogen generation. Crevice corrosion and hydrogen embrittlement are main causes of the damage of long term integrity of titanium overpack. However, it is not known about the corrosion resistance and hydrogen absorption behavior of titanium under reduction condition. In this study, the completely sealed ampoule test and the immersion test of titanium in aqueous solution and bentonite was carried out. In order to obtain reliable data about the hydrogen generation rate and the ratio of hydrogen absorption in titanium. From the result of 3 years immersion tests, corrosion rate of titanium were estimated to be in the order of 10 -2 ∼10 -1 μm/y in the aqueous solution, and 10 -3 ∼10 -2 μm/y in bentonite. This value is almost the same as the last report. Almost all the hydrogen generated by corrosion was absorbed in titanium in the immersion tests in completely sealed ampoule. In the examination that changed each parameter, it was suggested that the amount of the hydrogen absorption become 2∼3 times in 1M HCO 3- and pH13. (author)

  13. SAR: Stroke Authorship Recognition

    KAUST Repository

    Shaheen, Sara

    2015-10-15

    Are simple strokes unique to the artist or designer who renders them? If so, can this idea be used to identify authorship or to classify artistic drawings? Also, could training methods be devised to develop particular styles? To answer these questions, we propose the Stroke Authorship Recognition (SAR) approach, a novel method that distinguishes the authorship of 2D digitized drawings. SAR converts a drawing into a histogram of stroke attributes that is discriminative of authorship. We provide extensive classification experiments on a large variety of data sets, which validate SAR\\'s ability to distinguish unique authorship of artists and designers. We also demonstrate the usefulness of SAR in several applications including the detection of fraudulent sketches, the training and monitoring of artists in learning a particular new style and the first quantitative way to measure the quality of automatic sketch synthesis tools. © 2015 The Eurographics Association and John Wiley & Sons Ltd.

  14. An experimental investigation of the rate of hydrogen absorption in zirconium-2.5 wt percent niobium from steam/hydrogen mixtures at elevated temperatures

    International Nuclear Information System (INIS)

    Langman, V.J.

    1984-08-01

    The test specifications for an experimental program to study the rate of hydrogen absorption in zirconium-2.5 weight percent niobium pressure tube material from steam/hydrogen mixtures at elevated temperatures are discussed

  15. A Numerical Estimation of a RFID Reader Field and SAR inside a Blood Bag at UHF

    Directory of Open Access Journals (Sweden)

    Alessandro Fanti

    2016-11-01

    Full Text Available In this paper, the effects of UHF electromagnetic fields produced by a RFID reader on a blood bag are evaluated numerically in several configurations. The results of the simulation, field level and distribution, specific absorption rate (SAR, and heating time show that an exposure to a typical reader field leads to a temperature increase smaller than 0.1 C and to a SAR smaller than 1 W/kg. As a consequence, no adverse biological effects occur during a typical UHF RFID reading cycle on a blood bag. Therefore, the blood contained in a bag traced using UHF-RFID is as safe as those traced using barcodes. The proposed analysis supports the use of UHF RFID in the blood transfusion supply chain.

  16. SAR distribution in human beings when using body-worn RF transmitters

    International Nuclear Information System (INIS)

    Christ, A.; Samaras, T.; Neufeld, E.; Klingenboeck, A.; Kuster, N.

    2007-01-01

    This study analyzes the exposure of the human torso to electromagnetic fields caused by wireless body-mounted or hand-held devices. Because of the frequency and distance ranges from 30-5800 MHz and 10 to 200 mm, respectively, both near-field and far-field effects are considered. A generic body model and simulations of anatomical models are used to evaluate the worst case tissue composition with respect to the absorption of electromagnetic energy. Both standing wave effects and enhanced coupling of reactive near-field components can lead to a specific absorption rate (SAR) increase in comparison to homogeneous tissue. In addition, the exposure and temperature increase of different inner organs is assessed. With respect to compliance testing, the observed SAR enhancement may require the introduction of a multiplication factor for the spatial peak SAR measured in the liquid-filled phantom in order to obtain a conservative exposure assessment. The observed tissue heating at the body surface under adiabatic conditions can be significant, whereas the temperature increase in the inner organs turned out to be negligible for the cases investigated. (authors)

  17. Heating rates in furnace atomic absorption using the L'vov platform

    Science.gov (United States)

    Koirtyohann, S.R.; Giddings, R.C.; Taylor, Howard E.

    1984-01-01

    Heating rate profiles for the furnace tube wall, the furnace atmosphere, and a L'vov platform were established for a range of conditions in a cyclically heated graphite atomizer. The tube wall profile was made by direct observation with a recording optical pyrometer. The sodium line reversal method was used to establish the heating rate of the furnace atmosphere, and appearance temperatures for a series metals of differing volatility was used to establish platform profiles. The tube wall heating rate was nearly linear at 2240??C s- until the desired temperature was reached after which the temperature remained constant. The furnace atmosphere reached a given temperature 0.2-0.4 s later than the tube wall through most of the atomize cycle. The platform lagged the tube wall 0.5-0.8 s. Under typical operating conditions the furnace atmosphere was 100-200??C cooler than the tube wall and at nearly constant temperature when the analyte vaporized from the platform. The L'vov platform causes the cyclically heated commercial furnace to approximate the behavior of a constant temperature furnace during atomization. ?? 1984.

  18. Development of a carbonate absorption-based process for post-combustion CO2 capture: The role of biocatalyst to promote CO2 absorption rate

    Science.gov (United States)

    Lu, Y.; Ye, X.; Zhang, Z.; Khodayari, A.; Djukadi, T.

    2011-01-01

    An Integrated Vacuum Carbonate Absorption Process (IVCAP) for post-combustion carbon dioxide (CO2) capture is described. IVCAP employs potassium carbonate (PC) as a solvent, uses waste or low quality steam from the power plant for CO2 stripping, and employs a biocatalyst, carbonic anhydrase (CA) enzyme, for promoting the CO2 absorption into PC solution. A series of experiments were performed to evaluate the activity of CA enzyme mixed in PC solutions in a stirred tank reactor system under various temperatures, CA dosages, CO2 loadings, CO2 partial pressures, and the presence of major flue gas contaminants. It was demonstrated that CA enzyme is an effective biocatalyst for CO2 absorption under IVCAP conditions. ?? 2011 Published by Elsevier Ltd.

  19. Zinc absorption from composite meals. I. The significance of whest extraction rate, zinc, calcium, and protein content in meals based on bread.

    Science.gov (United States)

    Sandström, B; Arvidsson, B; Cederblad, A; Björn-Rasmussen, E

    1980-04-01

    The absorption of zinc in man from composite meals based on bread was measured with a radionuclide technique using 65Zn and whole-body counting. Bread was made up from wheat flour of 100 and 72% extraction rate. A lower absolute amount of zinc was absorbed from the white bread compared to the absorption from the same amount of wholemeal bread. When the two types of bread were enriched with zinc chloride the absorption was higher from the white bread than from the wholemeal bread. Addition of calcium in the form of milk products improved the absorption of zinc from a meal with wholemeal bread. A significant positive correlation was found between zinc absorption and the protein content in meals containing milk, cheese, beef, and egg in various combinations with the wholemeal bread.

  20. The rate of calcium extraction during EDTA decalcification from thin bone slices as assessed with atomic absorption spectrophotometry.

    Science.gov (United States)

    Kiviranta, I; Tammi, M; Lappalainen, R; Kuusela, T; Helminen, H J

    1980-01-01

    The rate of calcium extraction with EDTA (ethylenediamine tetraacetic acid) from thin bone slices (300 micrometer-3 mm thick) was determined by aid of an atomic absorption spectrophotometer. A 0.5 mm thick bone slice was completely decalcified with 15% (0.40 M), 8% (0.22 M), and 4% (0.11 M) EDTA in 24 h, 3 days, and 5 days, respectively (vol. 15 ml, temp. 4 degrees C, pH 7.4). At 37 and 60 degrees C the speed of demineralization was slightly increased as compared with that at 20 degrees C, while no difference was observed between 4 and 20 degrees C. Bone slices with a thickness of 0.3, 0.5, 1 and 2 mm were decalcified -- in the same order -- in 24 h, 2, 3, and 5 days (8% EDTA, 4 degrees C, pH 7.4). At pH 7.4, the decalcification rate was a little slower than at pH 5.0 and 8.5. Agitation did not affect the decalcifying velocity, nor did the volume of the agent, except when the volume was very small. The demineralization of ordinary bone, containing both compact and spongy bone, was found to be more rapid than that of homogeneous bone reported earlier. The acidic buffers and New Decalc, which served as reference substances, exerted a more vigorous decalcifying effect thatn EDTA. K formate/formic acid buffer, pH 3.15, demineralized a 1 mm thick bone slice in 24 h and 2 days was needed with Na lactate/lactic acid buffer, pH 3.70. With New Decalc, pH 0.9, the corresponding demineralization was accomplished in 1.5 h. Atomic absorption spectrophotometer proved to be a useful tool in the evaluation of calcium extraction velocity from bone slices.

  1. SARS – clinical features

    Indian Academy of Sciences (India)

    SARS – clinical features. Fever - > 38C; Respiratory symptoms, eg cough, difficulty in breathing; OR; Unexplained respiratory distress leading to death; AND; Close contact or travel to Asia within 10 days of onset of illness.

  2. Improving peak local SAR prediction in parallel transmit using in situ S-matrix measurements.

    Science.gov (United States)

    Restivo, Matthew; Raaijmakers, Alexander; van den Berg, Cornelis; Luijten, Peter; Hoogduin, Hans

    2017-05-01

    Peak local specific absorption rate (pSAR10g) is an important parameter used to determine patient safety during radiofrequency transmission. pSAR10g predictions for parallel transmit MRI are affected by the level of coupling exhibited by a modeled array in the simulation environment. However, simulated array coupling is rarely equal to the physical array coupling. Accurately simulating the physical array coupling may improve the accuracy of predicted SAR levels. The scattering parameter matrix (S-matrix) of a prototype 4-channel array was measured in situ using directional couplers installed on a 7T scanner. Agreement between the simulated and measured S-matrix was achieved by using network co-simulation with a modified cost function. B1+ maps acquired in a phantom were compared to B1+ distributions determined from simulations. The modified co-simulation technique forces the simulations to have S-matrices similar to the measured values. A comparison of realistically versus ideally simulated coupling conditions shows that ideally simulated coupling can result in large ( > 40%) error in pSAR10g predictions, even when the array is reasonably tuned. The simulated B1+ distributions match the measured B1+ distributions better when the coupling is accurately simulated. Considering the measured array coupling matrix in numerical simulations eliminates a potential confound in pSAR10g prediction. Magn Reson Med 77:2040-2047, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

  3. Growth rate anisotropy and absorption studies on β-BaB 2O 4 single crystals grown by the top-seeded solution growth technique

    Science.gov (United States)

    Bhatt, Rajeev; Ganesamoorthy, S.; Bhaumik, Indranil; Karnal, A. K.; Wadhawan, V. K.

    2007-03-01

    Beta barium borate (β-BaB2O4; BBO) single crystals have been grown from Na2O flux by the TSSG technique and the observed growth rate anisotropy is reported. The symmetrical conoscopic interference pattern on the c-cut plate confirmed strain-free and optical homogeneity of the crystals. The observed growth habits of as-grown crystals are explained using crystal growth theories. The relative growth rate along different crystallographic directions of BBO can be described by R[100] = R[010] > R[001]. The absorption measurements show a nearly 9 nm shift in fundamental absorption edges in X and Z cut samples. Band gap energies measured were 6.45 and 6.2 eV along the X and Z directions, respectively. The absorption spectra near the fundamental absorption edges (AE) follow Urbach's rule.

  4. Validation of Experimental whole-body SAR Assessment Method in a Complex Indoor Environment

    DEFF Research Database (Denmark)

    Bamba, Aliou; Joseph, Wout; Vermeeren, Gunter

    2012-01-01

    Assessing experimentally the whole-body specific absorption rate (SARwb) in a complex indoor environment is very challenging. An experimental method based on room electromagnetics theory (accounting only the Line-Of-Sight as specular path) to assess the whole-body SAR is validated by numerical...... simulations with the Finite-Difference Time-Domain method. Furthermore, the method accounts for the diffuse multipath components (DMC) in the total absorption rate by considering the reverberation time of the investigated room, which describes all the losses in a complex indoor environment. The advantage...... of the proposed method is that it allows discarding the computation burden because it does not use any discretizations. Results show good agreement between measurement and computation at 2.8 GHz, as long as the plane wave assumption is valid, i.e., for high distances from the transmitter. Relative deviations 0...

  5. [Study on lead absorption in pumpkin by atomic absorption spectrophotometry].

    Science.gov (United States)

    Li, Zhen-Xia; Sun, Yong-Dong; Chen, Bi-Hua; Li, Xin-Zheng

    2008-07-01

    A study was carried out on the characteristic of lead absorption in pumpkin via atomic absorption spectrophotometer. The results showed that lead absorption amount in pumpkin increased with time, but the absorption rate decreased with time; And the lead absorption amount reached the peak in pH 7. Lead and cadmium have similar characteristic of absorption in pumpkin.

  6. Adventures in SAR processing

    Science.gov (United States)

    Fiedler, Ralph; Jansen, Robert

    2000-04-01

    The image formation process associated with coherent imaging sensor is particularly sensitive to and is often corrupted by non-stationary processes. In the case of SAR, non- stationary processes result from motion within the scene, variable radar cross section, multi-path, topographic variations, sensor anomalies, and deficiencies in the image formation processing chain. Conversely, stationary processes result in image signatures that appear literal to the eye, e.g., urban infrastructure, vegetation, and natural terrain. In analyzing SAR signal history two objectives unfold. One is to obtain a well-focused image devoid of distortions and non-literal artifacts. The second objective is the detection and value-added exploitation of the non-stationary signatures. Note that the roles of signal and clutter are reversed for these two objectives. The notion that joint time-frequency (JTF) techniques may prove useful in accomplishing these objectives has spurred limited investigations into the field of coherent radar imaging systems. This paper addresses SAR image formation processing, the complex response function for a point source, and SAR JTF image formation implementations. Each of these topics is described within the context of applying JTF processing to all aspects of SAR image formation and analysis.

  7. Comparisons of Computed Mobile Phone Induced SAR in the SAM Phantom to That in Anatomically Correct Models of the Human Head

    Science.gov (United States)

    Beard, Brian B.; Kainz, Wolfgang; Onishi, Teruo; Iyama, Takahiro; Watanabe, Soichi; Fujiwara, Osamu; Wang, Jianqing; Bit-Babik, Giorgi; Faraone, Antonio; Wiart, Joe; Christ, Andreas; Kuster, Niels; Lee, Ae-Kyoung; Kroeze, Hugo; Siegbahn, Martin; Keshvari, Jafar; Abrishamkar, Houman; Simon, Winfried; Manteuffel, Dirk; Nikoloski, Neviana

    2018-01-01

    The specific absorption rates (SAR) determined computationally in the specific anthropomorphic mannequin (SAM) and anatomically correct models of the human head when exposed to a mobile phone model are compared as part of a study organized by IEEE Standards Coordinating Committee 34, SubCommittee 2, and Working Group 2, and carried out by an international task force comprising 14 government, academic, and industrial research institutions. The detailed study protocol defined the computational head and mobile phone models. The participants used different finite-difference time-domain software and independently positioned the mobile phone and head models in accordance with the protocol. The results show that when the pinna SAR is calculated separately from the head SAR, SAM produced a higher SAR in the head than the anatomically correct head models. Also the larger (adult) head produced a statistically significant higher peak SAR for both the 1- and 10-g averages than did the smaller (child) head for all conditions of frequency and position. PMID:29515260

  8. Severe acute respiratory syndrome (SARS)

    Science.gov (United States)

    ... their fever and other symptoms are gone. Hand hygiene is the most important part of SARS prevention. ... Coronaviruses, including severe acute respiratory syndrome (SARS) and Middle East respiratory syndrome (MERS). In: Bennett JE, Dolin ...

  9. Total Absorption Spectroscopy Study of the Beta Decay of 60Mn to Constrain the Neutron Capture Rate of 60Fe

    Science.gov (United States)

    Richman, Debra; Spyrou, Artemis; Dombos, Alex; Couture, Aaron; e15034 Collaboration

    2017-09-01

    Interest in 60Fe, a long lived radioisotope synthesized in massive stars, has recently peaked. The signature of its decay allows us to probe astrophysical processes, events such as the early formation of the solar system and nucleosynthesis. To understand these observations a complete understanding of the creation, destruction and nuclear properties of 60Fe in the astrophysical environment are required. Using the beta decay of 60Mn in conjunction with total absorption spectroscopy (TAS), made possible by the high efficiency gamma ray calorimeter SuN (Summing NaI detector) at the National Superconducting Cyclotron Laboratory (NSCL), to study the distribution of beta-decay intensity over the daughter-nucleus 60Fe, provides information about the structure of the daughter and improves the predictive power of astrophysical models. In addition to the ongoing TAS analysis, The Beta-Oslo method will be used to extract the nuclear level density and gamma-strength function of 60Fe providing much needed constraints on the neutron capture reaction rate responsible for the creation of this nucleus.

  10. Satellite on-board real-time SAR processor prototype

    Science.gov (United States)

    Bergeron, Alain; Doucet, Michel; Harnisch, Bernd; Suess, Martin; Marchese, Linda; Bourqui, Pascal; Desnoyers, Nicholas; Legros, Mathieu; Guillot, Ludovic; Mercier, Luc; Châteauneuf, François

    2017-11-01

    A Compact Real-Time Optronic SAR Processor has been successfully developed and tested up to a Technology Readiness Level of 4 (TRL4), the breadboard validation in a laboratory environment. SAR, or Synthetic Aperture Radar, is an active system allowing day and night imaging independent of the cloud coverage of the planet. The SAR raw data is a set of complex data for range and azimuth, which cannot be compressed. Specifically, for planetary missions and unmanned aerial vehicle (UAV) systems with limited communication data rates this is a clear disadvantage. SAR images are typically processed electronically applying dedicated Fourier transformations. This, however, can also be performed optically in real-time. Originally the first SAR images were optically processed. The optical Fourier processor architecture provides inherent parallel computing capabilities allowing real-time SAR data processing and thus the ability for compression and strongly reduced communication bandwidth requirements for the satellite. SAR signal return data are in general complex data. Both amplitude and phase must be combined optically in the SAR processor for each range and azimuth pixel. Amplitude and phase are generated by dedicated spatial light modulators and superimposed by an optical relay set-up. The spatial light modulators display the full complex raw data information over a two-dimensional format, one for the azimuth and one for the range. Since the entire signal history is displayed at once, the processor operates in parallel yielding real-time performances, i.e. without resulting bottleneck. Processing of both azimuth and range information is performed in a single pass. This paper focuses on the onboard capabilities of the compact optical SAR processor prototype that allows in-orbit processing of SAR images. Examples of processed ENVISAT ASAR images are presented. Various SAR processor parameters such as processing capabilities, image quality (point target analysis), weight and

  11. A new detection method of oil rigs in SAR imagery

    Science.gov (United States)

    Chen, Peng; Yang, Jingsong; Ren, Lin

    2013-10-01

    It's difficult for simple space-borne SAR to identify oil rigs effectively in single pass SAR image. One method of oil rig detection is using multi-temporal SAR images. Some papers had do some research on it. In this paper, we use interferometry SAR image to detect the oil rigs. We get the correlation coefficient image from the In-SAR data, and using the histogram of correlation coefficient image, A Constant False Alarm Rate (CFAR) algorithm is imported to detect the oil rigs. The Probabilistic Neural Network (PNN) is used to get the threshold of detection. The test result shows that sea coherent target detection in the coherent coefficient image is efficacious.

  12. Ship surveillance with Radarsat-2 ScanSAR

    Science.gov (United States)

    Wang, Ziwei; Zhang, Hong; Wang, Chao; Wu, Fan

    2014-10-01

    Ship detection is a significant application of maritime monitoring and security. To fully explore the potential of wide coverage of synthetic aperture radar (SAR) image, the ScanSAR Wide image for ship detection is investigated in this paper. The Radarsat-2 ScanSAR Wide mode image is used as the image source due to its huge coverage and constant false alarm rate (CFAR) with Gamma distribution is selected as the core detector. Two problems of ScanSAR ship detection, the unbalanced phenomenon and false alarms of islands, are investigated and solved by a compensation step and Hessian matrix respectively. For more aspects, the detector also concerns the polarization channel selection and distribution fitting. Finally, a whole flow chart of ScanSAR ship detection is presented. As test cases, the experimental image is used to show the efficiency of our method.

  13. Data Analytics for SAR

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, David Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Calef, Matthew Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-10-02

    We assess the ability of variants of anomalous change detection (ACD) to identify human activity associated with large outdoor music festivals as they are seen from synthetic aperture radar (SAR) imagery collected by the Sentinel-1 satellite constellation. We found that, with appropriate feature vectors, ACD using random-forest machine learning was most effective at identifying changes associated with the human activity.

  14. Multichannel FMCW SAR

    NARCIS (Netherlands)

    Rossum, W.L. van; Otten, M.P.G.; Dorp, Ph. van

    2012-01-01

    A light weight SAR, suitable for use on short range tactical UAV, has been designed and built. The system consists of a fully digital receive array, and a very compact active transmit antenna. The approximate weight of the complete system is 6 kg, with power consumption below 75 W, depending on the

  15. Bats and SARS

    Centers for Disease Control (CDC) Podcasts

    2006-11-08

    Bats are a natural reservoir for emerging viruses, among them henipaviruses and rabies virus variants. Dr. Nina Marano, Chief, Geographic Medicine and Health Promotion Branch, Division of Global Migration and Quarantine, CDC, explains connection between horseshoe bats and SARS coronavirus transmission.  Created: 11/8/2006 by Emerging Infectious Diseases.   Date Released: 11/17/2006.

  16. Bistatic SAR: Proof of Concept.

    Energy Technology Data Exchange (ETDEWEB)

    Yocky, David A.; Doren, Neall E.; Bacon, Terry A.; Wahl, Daniel E.; Eichel, Paul H.; Jakowatz, Charles V,; Delaplain, Gilbert G.; Dubbert, Dale F.; Tise, Bertice L.; White, Kyle R.

    2014-10-01

    Typical synthetic aperture RADAR (SAR) imaging employs a co-located RADAR transmitter and receiver. Bistatic SAR imaging separates the transmitter and receiver locations. A bistatic SAR configuration allows for the transmitter and receiver(s) to be in a variety of geometric alignments. Sandia National Laboratories (SNL) / New Mexico proposed the deployment of a ground-based RADAR receiver. This RADAR receiver was coupled with the capability of digitizing and recording the signal collected. SNL proposed the possibility of creating an image of targets the illuminating SAR observes. This document describes the developed hardware, software, bistatic SAR configuration, and its deployment to test the concept of a ground-based bistatic SAR. In the proof-of-concept experiments herein, the RADAR transmitter will be a commercial SAR satellite and the RADAR receiver will be deployed at ground level, observing and capturing RADAR ground/targets illuminated by the satellite system.

  17. A Comparative Study of the Effects of Substrate Composite Materials on External and Internal Handset Antenna EM Absorption

    Directory of Open Access Journals (Sweden)

    Md Ikbal HOSSAIN

    2016-09-01

    Full Text Available Cellular phones are used in the vicinity of a human head, which absorbs power from antenna radiation. This investigation analyzes the effects of antenna substrate materials on electromagnetic (EM absorption in a human head. Antennas are used in analysis with four different dielectric substrate materials, which are Bakelite, FR4 glass epoxy, Rogers R04003, and Taconic TLC. Moreover, two different thicknesses of each substrate are considered in the experimental setup. The EM absorption associated with two types of cell phone antennas is evaluated in the closed vicinity of the human head model. One of them is planar inverted-F antenna (PIFA, which is used as the internal handset antenna and another one is helical antenna, which is used as external handset antenna. This investigation consists of two different operating frequency bands, GSM 900 MHz and DCS 1800 MHz. The EM absorption in the human head is presented using the peak specific absorption rate (SAR and total absorbed power (TAP by the user. The finite-difference time-domain (FDTD method based on Computer Simulation Technology (CST Microwave studio is utilized in this investigation. The obtained results show that the substrate materials do not effect SAR and TAP values considerably for both antennas, but substrate thickness affects the SAR and TAP values significantly. In addition, the substrate thickness affects the SAR and TAP values significantly in most of the cases Moreover, PIFA produces lower SAR than that of a helical antenna significantly for both GSM and DCS frequency band.DOI: http://dx.doi.org/10.5755/j01.ms.22.3.8889

  18. DInSAR/PSInSAR Observations of Kirishima, Shinmoe-dake Volcano, Japan

    Science.gov (United States)

    Miyagi, Yousuke; Ozawa, Taku; Kozono, Tomofumi; Shimada, Masanobu

    2013-04-01

    Shinmoe-dake in the Kirishima volcano group is located in southwestern part of Japan. In January 2011, eruptive activities started from the Shinmoe-dake crater and resulted in sub-Plinian and Vulcanian eruptions and a rapid accumulation of lava within the crater. GPS and DInSAR data acquired before and after the eruption revealed pre-eruptive inflation, co-eruptive deflation, and post-eruptive inflation centered on 5km west of the crater. The eruption phase ceased by the beginning of September, and the post-eruptive inflation also ceased by November 2011. After the 2011 eruption, monitoring by TerraSAR-X have continued. Surface change and surface deformation on the lava within the crater were detected by high-resolution amplitude images and DInSAR data. Especially, the surface deformation after September 2011 revealed a continual shortening of satellite-ground distance even after the end of the main activity. This LOS shortening means uplifts of the lava surface. We estimated the volume increase of the lava after November 2011, using DInSAR processing of TerraSAR-X data, and concluded that the volume increase still continued in December 2012. The volume change rate has decreased with a small fluctuation as an overall trend. PSInSAR and long-term DInSAR results helped us to know deformation around the crater. They show LOS elongation including a subsidence in the northeast flank of the crater. It is interpreted that the subsidence is caused by a deflation of shallow deformation source located just beneath the crater.

  19. Time-resolved soft X-ray absorption spectroscopy in transmission mode on liquids at MHz repetition rates

    Directory of Open Access Journals (Sweden)

    Mattis Fondell

    2017-09-01

    Full Text Available We present a setup combining a liquid flatjet sample delivery and a MHz laser system for time-resolved soft X-ray absorption measurements of liquid samples at the high brilliance undulator beamline UE52-SGM at Bessy II yielding unprecedented statistics in this spectral range. We demonstrate that the efficient detection of transient absorption changes in transmission mode enables the identification of photoexcited species in dilute samples. With iron(II-trisbipyridine in aqueous solution as a benchmark system, we present absorption measurements at various edges in the soft X-ray regime. In combination with the wavelength tunability of the laser system, the set-up opens up opportunities to study the photochemistry of many systems at low concentrations, relevant to materials sciences, chemistry, and biology.

  20. Initial analysis of SAR from a cell phone inside a vehicle by numerical computation.

    Science.gov (United States)

    Anzaldi, Gabriel; Silva, Ferran; Fernández, Mireya; Quílez, Marcos; Riu, Pere J

    2007-05-01

    The purpose of this paper is to analyze the influence of the metallic structures of a realistic car body frame on the specific absorption rate (SAR) produced by a cell phone when a complete human body model is placed at different locations inside the vehicle, and to identify the relevant parameters responsible for these changes. The modeling and analysis of the whole system was conducted by means of computer simulations based on the full wave finite-difference time-domain (FDTD) numerical method. The excitation considered was an 835 MHz lambda/2 dipole located as a hands-free communication device or as a hand-held portable system. We compared the SAR at different planes on the human model, placed inside the vehicle with respect to the free space situation. The presence of the car body frame significantly changes the SAR distributions, especially when the dipole is far from the body. Although the results are not conclusive on this point, this change in SAR distribution is not likely to produce an increase above the limits in current guidelines for partial body exposure, but may be significant for whole-body exposure. The most relevant change found was the change in the impedance of the dipole, affecting the radiated power. A complementary result from the electromagnetic computations performed is the change in the electromagnetic field distribution inside a vehicle when human bodies are present. The whole vehicle model has been optimized to provide accurate results for sources placed inside the vehicle, while keeping low requirements for computer storage and simulation time.

  1. Bistatic sAR data processing algorithms

    CERN Document Server

    Qiu, Xiaolan; Hu, Donghui

    2013-01-01

    Synthetic Aperture Radar (SAR) is critical for remote sensing. It works day and night, in good weather or bad. Bistatic SAR is a new kind of SAR system, where the transmitter and receiver are placed on two separate platforms. Bistatic SAR is one of the most important trends in SAR development, as the technology renders SAR more flexible and safer when used in military environments. Imaging is one of the most difficult and important aspects of bistatic SAR data processing. Although traditional SAR signal processing is fully developed, bistatic SAR has a more complex system structure, so sign

  2. SAR++: A Multi-Channel Scalable and Reconfigurable SAR System

    DEFF Research Database (Denmark)

    Høeg, Flemming; Christensen, Erik Lintz

    2002-01-01

    SAR++ is a technology program aiming at developing know-how and technology needed to design the next generation civilian SAR systems. Technology has reached a state, which allows major parts of the digital subsystem to be built using custom-off-the-shelf (COTS) components. A design goal is to des......SAR++ is a technology program aiming at developing know-how and technology needed to design the next generation civilian SAR systems. Technology has reached a state, which allows major parts of the digital subsystem to be built using custom-off-the-shelf (COTS) components. A design goal...... is to design a modular, scalable and reconfigurable SAR system using such components, in order to ensure maximum flexibility for the users of the actual system and for future system updates. Having these aspects in mind the SAR++ system is presented with focus on the digital subsystem architecture...... and the analog to digital interface....

  3. 3D SAR approach to IF SAR processing

    Science.gov (United States)

    Doerry, Armin W.; Bickel, Doug

    2000-08-01

    Interferometric SAR (IFSAR) can be shown to be a special case of 3-D SAR image formation. In fact, traditional IFSAR processing results in the equivalent of merely a super- resolved, under-sampled, 3-D SAR image. However, when approached as a 3-D SAR problem, a number of IFSAR properties and anomalies are easily explained. For example, IFSAR decorrelation with height is merely ordinary migration in 3-D SAR. Consequently, treating IFSAR as a 3-D SAR problem allows insight and development of proper motion compensation techniques and image formation operations to facilitate optimal height estimation. Furthermore, multiple antenna phase centers and baselines are easily incorporated into this formulation, providing essentially a sparse array in the elevation dimension. This paper shows the Polar Format image formation algorithm extended to 3 dimensions, and then proceeds to apply it to the IFSAR collection geometry. This suggests a more optimal reordering of the traditional IFSAR processing steps.

  4. InSAR processing for the recognition of landslides

    Directory of Open Access Journals (Sweden)

    B. Riedel

    2008-01-01

    Full Text Available Synthetic Aperture Radar Interferometry (InSAR is an established method for the detection and monitoring of earth surface processes. This approach has been most successful where the observed area fulfills specific requirements, such as sufficient backscattering, flat slope gradients or very slow changes of vegetation. We investigated the capability of two different InSAR techniques and achieved good results for the recognition of landslides in China and Greece that compared well with geodetic derived movement rates. This demonstrates the strong potential of SAR Interferometry for the detection of landslides and earth surface movements.

  5. A New SAR Image Segmentation Algorithm for the Detection of Target and Shadow Regions

    Science.gov (United States)

    Huang, Shiqi; Huang, Wenzhun; Zhang, Ting

    2016-01-01

    The most distinctive characteristic of synthetic aperture radar (SAR) is that it can acquire data under all weather conditions and at all times. However, its coherent imaging mechanism introduces a great deal of speckle noise into SAR images, which makes the segmentation of target and shadow regions in SAR images very difficult. This paper proposes a new SAR image segmentation method based on wavelet decomposition and a constant false alarm rate (WD-CFAR). The WD-CFAR algorithm not only is insensitive to the speckle noise in SAR images but also can segment target and shadow regions simultaneously, and it is also able to effectively segment SAR images with a low signal-to-clutter ratio (SCR). Experiments were performed to assess the performance of the new algorithm on various SAR images. The experimental results show that the proposed method is effective and feasible and possesses good characteristics for general application. PMID:27924935

  6. Wetland InSAR

    Science.gov (United States)

    Wdowinski, S.; Kim, S.; Amelung, F.; Dixon, T.

    2006-12-01

    Wetlands are transition zones where the flow of water, the nutrient cycling, and the sun energy meet to produce a unique and very productive ecosystem. They provide critical habitat for a wide variety of plant and animal species, including the larval stages of many ocean fish. Wetlands also have a valuable economical importance, as they filter nutrients and pollutants from fresh water used by human and provide aquatic habitats for outdoor recreation, tourism, and fishing. Globally, many such regions are under severe environmental stress, mainly from urban development, pollution, and rising sea level. However, there is increasing recognition of the importance of these habitats, and mitigation and restoration activities have begun in a few regions. A key element in wetlands conservation, management, and restoration involves monitoring its hydrologic system, as the entire ecosystem depends on its water supply. Heretofore, hydrologic monitoring of wetlands are conducted by stage (water level) stations, which provide good temporal resolution, but suffer from poor spatial resolution, as stage station are typically distributed several, or even tens of kilometers, from one another. Wetland application of InSAR provides the needed high spatial resolution hydrological observations, complementing the high temporal resolution terrestrial observations. Although conventional wisdom suggests that interferometry does not work in vegetated areas, several studies have shown that both L- and C-band interferograms with short acquisition intervals (1-105 days) can maintain excellent coherence over wetlands. In this study we explore the usage of InSAR for detecting water level changes in various wetland environments around the world, including the Everglades (south Florida), Louisiana Coast (southern US), Chesapeake Bay (eastern US), Pantanal (Brazil), Okavango Delta (Botswana), and Lena Delta (Siberia). Our main study area is the Everglades wetland (south Florida), which is covered by

  7. Novel Polarimetric SAR Interferometry Algorithms, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Polarimetric SAR interferometry (PolInSAR) is a recently developed synthetic aperture radar (SAR) imaging mode that combines the capabilities of radar polarimetry...

  8. New challenges for a SAR toolbox

    International Nuclear Information System (INIS)

    Loreaux, P.; Quin, G.

    2013-01-01

    High resolution multi-frequency synthetic aperture radar (SAR) imagery, available since early 2008, brings all weather capability and day/night operability in support of safeguards verification. Today, a combined approach of high resolution optical and radar imagery in monitoring exercise would enable looking at any area of interest on daily basis. One of the challenges is the co-registration of SAR images acquired with different acquisition mode and also with different optical images. We show in this paper the on-going research work to find a general co-register method and an automatic tool to detect changes. Before having an operational co-register tool, a method to find automatically tie points between SAR images acquired with different acquisition mode and with optical images has to be developed. Concerning an automatic change detection method we can conclude that the study of the Harmonic mean, Geometric mean and Arithmetic mean, enables several applications like change detection for SAR imagery. Thus, we developed the MAGMA (Method for Arithmetic and Geometric Means Analysis) change detection method. As shown in this paper, the MAGMA method improves the Maximum Likelihood techniques like GLRT, using Information-Theory concepts to detect changes between SAR amplitude images. The major improvement consists in a lower false detection rate, especially in low amplitude areas. The second improvement consists in a better location of the changes in clearly delimited areas, which enables precise interpretations. Results presented here reveal the potential of high resolution radar imagery for a baseline description of some sites, change detection based on repeat pass imagery acquisitions and site specific constraints in coherent change detection due to cover conditions. (A.C.)

  9. Multiplier-free filters for wideband SAR

    DEFF Research Database (Denmark)

    Dall, Jørgen; Christensen, Erik Lintz

    2001-01-01

    This paper derives a set of parameters to be optimized when designing filters for digital demodulation and range prefiltering in SAR systems. Aiming at an implementation in field programmable gate arrays (FPGAs), an approach for the design of multiplier-free filters is outlined. Design results ar...... are presented in terms of filter complexity and performance. One filter has been coded in VHDL and preliminary results indicate that the filter can meet a 2 GHz input sample rate....

  10. SAR and thermal response effects of a two-arm Archimedean spiral coil in a magnetic induction sensor on a human head.

    Science.gov (United States)

    Zhang, Ziyi; Liu, Peiguo; Zhou, Dongming; Zhang, Liang; Ding, Liang

    2015-01-01

    This study investigates the radiation safety of a newly designed magnetic induction sensor. This novel magnetic induction sensor uses a two-arm Archimedean spiral coil (TAASC) as the exciter. A human head model with a real anatomical structure was used to calculate the specific absorption rate (SAR) and temperature change. Computer Simulation Technology (CST) was used to determine the values of the peak 10-g SAR under different operating parameters (current, frequency, horizontal distance between the excitation coil and the receiver coil, vertical distance between the top of the head model and the XOY plane, position of excitation coil, and volume of hemorrhage). Then, the highest response for the SAR and temperature rise was determined. The results showed that this new magnetic induction sensor is safe in the initial state; for safety reasons, the TAASC current should not exceed 4 A. The scalp tissue absorbed most of the electromagnetic energy. The TAASC's SAR/thermal performance was close to that of the circular coil.

  11. Demonstration MTI/SAR capability

    NARCIS (Netherlands)

    Vries, F.P.P. de; Broek, A.C. van den; Otten, M.P.G.; Groot, J.S.; Steeghs, T.P.H.; Dekker, R.J.; Rossum, W.L. van

    2001-01-01

    The aim of this project is to demonstrate to the Dutch armed forces the capability of MTI (Moving Target Indicator) and SAR (Synthetic Aperture Radar). This is done with the Dutch PHARUS sensor. The sensor is used to demonstrate how a phased array antenna can be used as an MTI/SAR sensor

  12. How infectious is SARS virus

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. How infectious is SARS virus. Influenza: 1 patient infects ten people. SARS: 1 patient infects 2-4 people. Incubation period 10 days. Are there `silent´ cases ? Is quarantine enough ? How will it behave if and when it returns ?

  13. PHARUS : PHased ARray Universal SAR

    NARCIS (Netherlands)

    Paquay, M.H.A.; Vermeulen, B.C.B.; Koomen, P.J.; Hoogeboom, P.; Snoeij, P.; Pouwels, H.

    1996-01-01

    In the Netherlands, a polarimetric C-band aircraft SAR (Synthetic Aperture Radar) has been developed. The project is called PHARUS, an acronm for PHased ARray Universal SAR. This instrument serves remote sensing applications. The antenna system contains 48 active modules (expandable to 96). A module

  14. Addition of sodium bicarbonate to either 1 or 2 feedings of colostrum replacer: effect on uptake and rate of absorption of immunoglobulin G in neonatal calves.

    Science.gov (United States)

    Cabral, R G; Kent, E J; Haines, D M; Erickson, P S

    2012-06-01

    Forty Holstein dairy calves were blocked by birth date and sex, and randomly assigned to 1 of 4 treatments within each block to elucidate the effect of feeding regimen and sodium bicarbonate (NaHCO₃) supplementation on absorption of IgG from colostrum replacer (CR). Calves received CR containing 191.4 g of IgG fed either in 1 feeding at 0 h (within 45 min of birth), with or without 30 g of NaHCO₃, or in 2 feedings (127.6 g of IgG at 0 h, with or without 20 g of NaHCO₃, and 63.8 g of IgG at 6 h, with or without 10 g of NaHCO₃). The treatments were (1) 1 feeding of CR+0 g of NaHCO₃; (2) 1 feeding of CR+30 g of NaHCO₃; (3) 2 feedings of CR+0 g of NaHCO₃; and (4) 2 feedings of CR+30 g total of NaHCO₃. Only calves born with no dystocia were used on this study. Blood samples were taken at 0, 6, 12, 18, and 24h postpartum and were analyzed for IgG using a radial immunoassay. Results indicated that, individually, feeding regimen and NaHCO₃ treatments had no effect. However, the interaction was significant for 24-h IgG and area under the curve, and showed a trend for apparent efficiency of absorption. Absorption rate data indicated that, for calves fed within 45 min of birth, most IgG absorption occurred in the first 6 h after birth. From 6 to 12 h postpartum, IgG absorption started to decrease; however, IgG absorption remained higher for calves fed in a single feeding than in 2 feedings. These data indicated that NaHCO₃ may increase IgG absorption when calves are fed colostrum in a single feeding but is not beneficial when colostrum is fed in 2 feedings. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  15. Bistatic SAR: Imagery & Image Products.

    Energy Technology Data Exchange (ETDEWEB)

    Yocky, David A.; Wahl, Daniel E.; Jakowatz, Charles V,

    2014-10-01

    While typical SAR imaging employs a co-located (monostatic) RADAR transmitter and receiver, bistatic SAR imaging separates the transmitter and receiver locations. The transmitter and receiver geometry determines if the scattered signal is back scatter, forward scatter, or side scatter. The monostatic SAR image is backscatter. Therefore, depending on the transmitter/receiver collection geometry, the captured imagery may be quite different that that sensed at the monostatic SAR. This document presents imagery and image products formed from captured signals during the validation stage of the bistatic SAR research. Image quality and image characteristics are discussed first. Then image products such as two-color multi-view (2CMV) and coherent change detection (CCD) are presented.

  16. Thermal Index Evaluation of Local SAR in MRI-Based Head Models of Adult and Children for Portable Telephones

    Science.gov (United States)

    Fujiwara, Osamu; Miyamoto, Kayoko; Wang, Jianqing

    Biological hazards due to radio-frequency (RF) waves result mainly from the temperature rise in tissue. It should be, therefore, clarified to what extent the RF waves of portable telephones increase the temperature-rise in human brain that includes the central part governing the body-temperature regulation function. In this paper, we calculated both the specific absorption rate (SAR) and the resultant temperature-rise for 900 MHz and 2 GHz portable telephones using the finite-difference time-domain (FDTD) method for three typical use positions, i.e., the vertical position, cheek position and tilt position. As a result, we found that there was an increase for median and 1% value of the cumulative distribution of temperature-rise in children’s brains for any use positions of the portable telephones compared to that in the adult’s brain, and also that the increasing trend in children’s brains for temperature-rise is identical to the temperature-rise trend in children’s hypothalamus. In addition, we found that the ten-gram averaged peak SAR among the adult and children heads had the same trend as that of the 0.1% value of the relatively cumulative distribution of temperature-rise, which shows that the ten-gram averaged peak SAR reflects only the localized temperature-rise in the brain surface.

  17. Comparison of SAR and induced current densities in adults and children exposed to electromagnetic fields from electronic article surveillance devices

    Science.gov (United States)

    Martínez-Búrdalo, M.; Sanchis, A.; Martín, A.; Villar, R.

    2010-02-01

    Electronic article surveillance (EAS) devices are widely used in most stores as anti-theft systems. In this work, the compliance with international guidelines in the human exposure to these devices is analysed by using the finite-difference time-domain (FDTD) method. Two sets of high resolution numerical phantoms of different size (REMCOM/Hershey and Virtual Family), simulating adult and child bodies, are exposed to a 10 MHz pass-by panel-type EAS consisting of two overlapping current-carrying coils. Two different relative positions between the EAS and the body (frontal and lateral exposures), which imply the exposure of different parts of the body at different distances, have been considered. In all cases, induced current densities in tissues of the central nervous system and specific absorption rates (SARs) are calculated to be compared with the limits from the guidelines. Results show that induced current densities are lower in the case of adult models as compared with those of children in both lateral and frontal exposures. Maximum SAR values calculated in lateral exposure are significantly lower than those calculated in frontal exposure, where the EAS-body distance is shorter. Nevertheless, in all studied cases, with an EAS driving current of 4 A rms, maximum induced current and SAR values are below basic restrictions.

  18. Comparison of SAR and induced current densities in adults and children exposed to electromagnetic fields from electronic article surveillance devices

    International Nuclear Information System (INIS)

    Martinez-Burdalo, M; Sanchis, A; Martin, A; Villar, R

    2010-01-01

    Electronic article surveillance (EAS) devices are widely used in most stores as anti-theft systems. In this work, the compliance with international guidelines in the human exposure to these devices is analysed by using the finite-difference time-domain (FDTD) method. Two sets of high resolution numerical phantoms of different size (REMCOM/Hershey and Virtual Family), simulating adult and child bodies, are exposed to a 10 MHz pass-by panel-type EAS consisting of two overlapping current-carrying coils. Two different relative positions between the EAS and the body (frontal and lateral exposures), which imply the exposure of different parts of the body at different distances, have been considered. In all cases, induced current densities in tissues of the central nervous system and specific absorption rates (SARs) are calculated to be compared with the limits from the guidelines. Results show that induced current densities are lower in the case of adult models as compared with those of children in both lateral and frontal exposures. Maximum SAR values calculated in lateral exposure are significantly lower than those calculated in frontal exposure, where the EAS-body distance is shorter. Nevertheless, in all studied cases, with an EAS driving current of 4 A rms, maximum induced current and SAR values are below basic restrictions.

  19. Assessment of exposure to radio frequency electromagnetic fields from smart utility meters in GB; part II) numerical assessment of induced SAR within the human body.

    Science.gov (United States)

    Qureshi, Muhammad R A; Alfadhl, Yasir; Chen, Xiaodong; Peyman, Azadeh; Maslanyj, Myron; Mann, Simon

    2018-04-01

    Human body exposure to radiofrequency electromagnetic waves emitted from smart meters was assessed using various exposure configurations. Specific energy absorption rate distributions were determined using three anatomically realistic human models. Each model was assigned with age- and frequency-dependent dielectric properties representing a collection of age groups. Generalized exposure conditions involving standing and sleeping postures were assessed for a home area network operating at 868 and 2,450 MHz. The smart meter antenna was fed with 1 W power input which is an overestimation of what real devices typically emit (15 mW max limit). The highest observed whole body specific energy absorption rate value was 1.87 mW kg -1 , within the child model at a distance of 15 cm from a 2,450 MHz device. The higher values were attributed to differences in dimension and dielectric properties within the model. Specific absorption rate (SAR) values were also estimated based on power density levels derived from electric field strength measurements made at various distances from smart meter devices. All the calculated SAR values were found to be very small in comparison to International Commission on Non-Ionizing Radiation Protection limits for public exposure. Bioelectromagnetics. 39:200-216, 2018. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  20. Assessment of the computational uncertainty of temperature rise and SAR in the eyes and brain under far-field exposure from 1 to 10 GHz

    International Nuclear Information System (INIS)

    Laakso, Ilkka

    2009-01-01

    This paper presents finite-difference time-domain (FDTD) calculations of specific absorption rate (SAR) values in the head under plane-wave exposure from 1 to 10 GHz using a resolution of 0.5 mm in adult male and female voxel models. Temperature rise due to the power absorption is calculated by the bioheat equation using a multigrid method solver. The computational accuracy is investigated by repeating the calculations with resolutions of 1 mm and 2 mm and comparing the results. Cubically averaged 10 g SAR in the eyes and brain and eye-averaged SAR are calculated and compared to the corresponding temperature rise as well as the recommended limits for exposure. The results suggest that 2 mm resolution should only be used for frequencies smaller than 2.5 GHz, and 1 mm resolution only under 5 GHz. Morphological differences in models seemed to be an important cause of variation: differences in results between the two different models were usually larger than the computational error due to the grid resolution, and larger than the difference between the results for open and closed eyes. Limiting the incident plane-wave power density to smaller than 100 W m -2 was sufficient for ensuring that the temperature rise in the eyes and brain were less than 1 deg. C in the whole frequency range.

  1. Assessment of the computational uncertainty of temperature rise and SAR in the eyes and brain under far-field exposure from 1 to 10 GHz

    Science.gov (United States)

    Laakso, Ilkka

    2009-06-01

    This paper presents finite-difference time-domain (FDTD) calculations of specific absorption rate (SAR) values in the head under plane-wave exposure from 1 to 10 GHz using a resolution of 0.5 mm in adult male and female voxel models. Temperature rise due to the power absorption is calculated by the bioheat equation using a multigrid method solver. The computational accuracy is investigated by repeating the calculations with resolutions of 1 mm and 2 mm and comparing the results. Cubically averaged 10 g SAR in the eyes and brain and eye-averaged SAR are calculated and compared to the corresponding temperature rise as well as the recommended limits for exposure. The results suggest that 2 mm resolution should only be used for frequencies smaller than 2.5 GHz, and 1 mm resolution only under 5 GHz. Morphological differences in models seemed to be an important cause of variation: differences in results between the two different models were usually larger than the computational error due to the grid resolution, and larger than the difference between the results for open and closed eyes. Limiting the incident plane-wave power density to smaller than 100 W m-2 was sufficient for ensuring that the temperature rise in the eyes and brain were less than 1 °C in the whole frequency range.

  2. Air pollution and case fatality of SARS in the People's Republic of China: an ecologic study

    Directory of Open Access Journals (Sweden)

    Yu Shun-Zhang

    2003-11-01

    Full Text Available Abstract Background Severe acute respiratory syndrome (SARS has claimed 349 lives with 5,327 probable cases reported in mainland China since November 2002. SARS case fatality has varied across geographical areas, which might be partially explained by air pollution level. Methods Publicly accessible data on SARS morbidity and mortality were utilized in the data analysis. Air pollution was evaluated by air pollution index (API derived from the concentrations of particulate matter, sulfur dioxide, nitrogen dioxide, carbon monoxide and ground-level ozone. Ecologic analysis was conducted to explore the association and correlation between air pollution and SARS case fatality via model fitting. Partially ecologic studies were performed to assess the effects of long-term and short-term exposures on the risk of dying from SARS. Results Ecologic analysis conducted among 5 regions with 100 or more SARS cases showed that case fatality rate increased with the increment of API (case fatality = - 0.063 + 0.001 * API. Partially ecologic study based on short-term exposure demonstrated that SARS patients from regions with moderate APIs had an 84% increased risk of dying from SARS compared to those from regions with low APIs (RR = 1.84, 95% CI: 1.41–2.40. Similarly, SARS patients from regions with high APIs were twice as likely to die from SARS compared to those from regions with low APIs. (RR = 2.18, 95% CI: 1.31–3.65. Partially ecologic analysis based on long-term exposure to ambient air pollution showed the similar association. Conclusion Our studies demonstrated a positive association between air pollution and SARS case fatality in Chinese population by utilizing publicly accessible data on SARS statistics and air pollution indices. Although ecologic fallacy and uncontrolled confounding effect might have biased the results, the possibility of a detrimental effect of air pollution on the prognosis of SARS patients deserves further investigation.

  3. On the effects of straight metallic jewellery on the specific absorption rates resulting from face-illuminating radio communication devices at popular cellular frequencies

    International Nuclear Information System (INIS)

    Whittow, W G; Panagamuwa, C J; Edwards, R M; Vardaxoglou, J C

    2008-01-01

    This paper presents simulated and measured phantom results for the possible effects that head worn jewellery may have on the relative levels of energy absorbed in the human head with cellular enabled mobile communication devices. The FDTD electromagnetic code used with simple and complex anatomical mathematical phantoms was used to consider the interactions of metallic jewellery, heads and representative sources at 900 and 1800 MHz. Illuminated metallic pins of different lengths were positioned in front of the face. Initially, a homogenous phantom was used to understand the relative enhancement mechanisms. This geometry allowed the results to be validated with the industry standard DASY4 robot SAR measurement system related to the CENELEC head. Jewellery pins were then added to an anatomically realistic head. The relative increase in the 1 g and 10 g SAR, due to a pin with a length 0.4λ near the eyebrows of a complex, anatomically realistic head was approximately three times at 1800 MHz. Such pins increased the SAR averaged over a 1 g or 10 g mass by redistributing the energy absorbed inside the head and focusing this energy towards the area of the head nearest to the centre of the pin. Although, the pins increased the SAR, the SAR standards were not breached and the jewellery produced lower values than those of previous studies when the source was positioned close to the ear

  4. High Resolution Processing with an Active Phased Array SAR

    NARCIS (Netherlands)

    Nijenboer, F.J.; Otten, M.P.G.

    1999-01-01

    The Dutch PHARUS system is a polarimetric active phased array SAR capable of performing advanced SAR modes. Advanced SAR modes that are being investigated are: spotlight SAR, sliding spotlight SAR, stepped frequency SAR and interferometric SAR. The flight experiments and automatic beam steering

  5. Effect of enteral formula infusion rate, osmolality, and chemical composition upon clinical tolerance and carbohydrate absorption in normal subjects.

    Science.gov (United States)

    Zarling, E J; Parmar, J R; Mobarhan, S; Clapper, M

    1986-01-01

    It is a common clinical practice to initiate enteral hyperalimentation using low flow rates or diluted formula. These adjustments are made in an effort to minimize patient intolerance. Using complex and elemental enteral formulas, we investigated whether various flow rates or osmolalities effected clinical intolerance or carbohydrate malabsorption in 20 healthy volunteers. Our infusion rates ranged between 50 and 150 kcal/hr and the osmolalities ranged between 325 and 690 mOsm/Kg of water. Even at the maximal flow rate and osmolality, our results show that both types of enteral formulas were well tolerated as assessed by the frequency of abdominal pain, bloating, passage of rectal gas and stooling. No carbohydrate malabsorption was detected as measured by breath hydrogen. In well nourished subjects, our findings do not support the common clinical practice of initiating alimentation with low flow rates or diluted formula.

  6. Relationship between turnover rate and oxidation rate of alanine in the post-absorptive state and during parenteral nutrition before and after surgery

    NARCIS (Netherlands)

    Sauerwein, H. P.; Michels, R. P.; Cejka, V.

    1985-01-01

    The influence of total parenteral nutrition and stomach resection on alanine turnover rate and alanine oxidation rate was measured in ten patients after single injection of U-14 C-alanine. Sequential studies were done in three patients. During parenteral nutrition alanine turnover was significantly

  7. First Spaceborne SAR-GMTI Experimental Results for the Chinese Gaofen-3 Dual-Channel SAR Sensor.

    Science.gov (United States)

    Wang, Chenghao; Liao, Guisheng; Zhang, Qingjun

    2017-11-21

    In spaceborne synthetic aperture radar (SAR) sensors, it is a challenging task to detect ground slow-moving targets against strong clutter background with limited spatial channels and restricted pulse repetition frequency (PRF). In this paper, we evaluate the image-based dual-channel SAR-ground moving target indication (SAR-GMTI) workflow for the Gaofen-3 SAR sensor and analyze the impact of strong azimuth ambiguities on GMTI when the displaced phase center antenna (DPCA) condition is not fully satisfied, which has not been demonstrated yet. An effective sliding window design technique based on system parameters analysis is proposed to deal with azimuth ambiguities and reduce false alarm. In the SAR-GMTI experiments, co-registration, clutter suppression, constant false alarm rate (CFAR) detector, vector velocity estimation and moving target relocation are analyzed and discussed thoroughly. With the real measured data of the Gaofen-3 dual-channel SAR sensor, the GMTI capability of this sensor is demonstrated and the effectiveness of the proposed method is verified.

  8. First Spaceborne SAR-GMTI Experimental Results for the Chinese Gaofen-3 Dual-Channel SAR Sensor

    Directory of Open Access Journals (Sweden)

    Chenghao Wang

    2017-11-01

    Full Text Available In spaceborne synthetic aperture radar (SAR sensors, it is a challenging task to detect ground slow-moving targets against strong clutter background with limited spatial channels and restricted pulse repetition frequency (PRF. In this paper, we evaluate the image-based dual-channel SAR-ground moving target indication (SAR-GMTI workflow for the Gaofen-3 SAR sensor and analyze the impact of strong azimuth ambiguities on GMTI when the displaced phase center antenna (DPCA condition is not fully satisfied, which has not been demonstrated yet. An effective sliding window design technique based on system parameters analysis is proposed to deal with azimuth ambiguities and reduce false alarm. In the SAR-GMTI experiments, co-registration, clutter suppression, constant false alarm rate (CFAR detector, vector velocity estimation and moving target relocation are analyzed and discussed thoroughly. With the real measured data of the Gaofen-3 dual-channel SAR sensor, the GMTI capability of this sensor is demonstrated and the effectiveness of the proposed method is verified.

  9. The Influence of Low Salivary Flow Rates on the Absorption of a Sublingual Fentanyl Citrate Formulation for Breakthrough Cancer Pain.

    Science.gov (United States)

    Davies, Andrew; Mundin, Gill; Vriens, Joanna; Webber, Kath; Buchanan, Alison; Waghorn, Melanie

    2016-03-01

    Salivary gland hypofunction may affect the absorption of drugs through the oral mucosa, which in turn may affect their clinical efficacy (e.g., onset of action). The aim of this study was to assess the pharmacokinetics of a sublingual fentanyl orally disintegrating tablet (Abstral, Prostrakan Inc.) in a group of cancer patients with salivary gland hypofunction. Nine cancer patients with salivary gland hypofunction underwent a series of three pharmacokinetic studies with the sublingual fentanyl orally disintegrating tablet. In the first phase, the patients received no pretreatment; in the second phase, the patients were allowed to moisten the oral cavity before dosing; in the third phase, the patients were given pilocarpine hydrochloride (saliva stimulant) before dosing. Fentanyl concentrations were measured using a method of high-performance liquid chromatography with validated tandem mass spectrometric detection. The Tmax was longer, the Cmax was lower, the AUC0-30 lower, and the AUClast lower in the phase involving no pretreatment; the Tmax/Cmax/AUC0-30/AUClast were similar in the phase involving moistening of the oral cavity and the phase involving giving pilocarpine hydrochloride. The pharmacokinetics of the sublingual fentanyl orally disintegrating tablet appear to be negatively affected by the presence of salivary gland hypofunction, although the moistening of the oral cavity before dosing results in a pharmacokinetic profile similar to that seen with the giving of pilocarpine hydrochloride. Copyright © 2016 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

  10. Prevalence of psychiatric morbidity and psychological adaptation of the nurses in a structured SARS caring unit during outbreak: a prospective and periodic assessment study in Taiwan.

    Science.gov (United States)

    Su, Tung-Ping; Lien, Te-Cheng; Yang, Chih-Yi; Su, Yiet Ling; Wang, Jia-Horng; Tsai, Sing-Ling; Yin, Jeo-Chen

    2007-01-01

    To assess the rapidly changing psychological status of nurses during the acute phase of the 2003 SARS outbreak, we conducted a prospective and periodic evaluation of psychiatric morbidity and psychological adaptation among nurses in SARS units and non-SARS units. Nurse participants were from two SARS units (regular SARS [N=44] and SARS ICU [N=26]) and two non-SARS units (Neurology [N=15] and CCU [N=17]). Participants periodically self-evaluated their depression, anxiety, post-traumatic stress symptoms, sleep disturbance, attitude towards SARS and family support. Results showed that depression (38.5% vs. 3.1%) and insomnia (37% vs. 9.7%) were, respectively, greater in the SARS unit nurses than the non-SARS unit nurses. No difference between these two groups was found in the prevalence of post-traumatic stress symptoms (33% vs. 18.7%), yet, three unit subjects (SARS ICU, SARS regular and Neurology) had significantly higher rate than those in CCU (29.7% vs. 11.8%, respectively) (pregular SARS unit. Occurrence of psychiatric symptoms was linked to direct exposure to SARS patient care, previous mood disorder history, younger age and perceived negative feelings. Positive coping attitude and strong social and family support may have protected against acute stress. In conclusion, the psychological impact on the caring staffs facing future bio-disaster will be minimized with lowered risk factors and a safer and more structured work environment.

  11. TerraSAR-X mission

    Science.gov (United States)

    Werninghaus, Rolf

    2004-01-01

    The TerraSAR-X is a German national SAR- satellite system for scientific and commercial applications. It is the continuation of the scientifically and technologically successful radar missions X-SAR (1994) and SRTM (2000) and will bring the national technology developments DESA and TOPAS into operational use. The space segment of TerraSAR-X is an advanced high-resolution X-Band radar satellite. The system design is based on a sound market analysis performed by Infoterra. The TerraSAR-X features an advanced high-resolution X-Band Synthetic Aperture Radar based on the active phased array technology which allows the operation in Spotlight-, Stripmap- and ScanSAR Mode with various polarizations. It combines the ability to acquire high resolution images for detailed analysis as well as wide swath images for overview applications. In addition, experimental modes like the Dual Receive Antenna Mode allow for full-polarimetric imaging as well as along track interferometry, i.e. moving target identification. The Ground Segment is optimized for flexible response to (scientific and commercial) User requests and fast image product turn-around times. The TerraSAR-X mission will serve two main goals. The first goal is to provide the strongly supportive scientific community with multi-mode X-Band SAR data. The broad spectrum of scientific application areas include Hydrology, Geology, Climatology, Oceanography, Environmental Monitoring and Disaster Monitoring as well as Cartography (DEM Generation) and Interferometry. The second goal is the establishment of a commercial EO-market in Europe which is driven by Infoterra. The commercial goal is the development of a sustainable EO-business so that the e.g. follow-on systems can be completely financed by industry from the profit. Due to its commercial potential, the TerraSAR-X project will be implemented based on a public-private partnership with the Astrium GmbH. This paper will describe first the mission objectives as well as the

  12. Siyah Sarımsak

    Directory of Open Access Journals (Sweden)

    Selen Akan

    2015-02-01

    Full Text Available Sarımsağın insan sağlığına yararları yüzyıllardır yaygın olarak bilinmektedir. Besin içeriği nedeniyle uzmanların şiddetle tavsiye etmelerine ve beslenme programlarına mutlaka eklenilmesine rağmen keskin kokusu nedeniyle birçok kişi tüketmekten kaçınmaktadır. Sarımsağın bu dezavantajı için alternatif olarak siyah sarımsak gündeme getirilmiştir. Siyah sarımsak, taze sarımsağın fermente edilip, tamamen siyah rengini alana kadar koyu renge dönüşümü ile oluşmakta ve bu süreçte besin içeriği de değişim göstermektedir. Fermantasyon işlemi ile sarımsak başlarının karakteristik kokusunu veren öncül maddeleri alliin ve allicin azalmakta böylelikle hem istenmeyen kokusunu kaybetmekte hem de tadındaki acılık kaybolmaktadır. Siyah sarımsak, taze sarımsağa oranla yüksek oranda antioksidan aktiviteye sahiptir. Bu özelliği, sadece koku ve lezzet olarak değil, besin içeriğiyle de beslenme takviyesinde kullanımını daha çekici hale getirmiştir. Siyah sarımsak Asya ve Avrupa ülkelerinde henüz yeni beğeni toplamaya başlamıştır. Japonya ve Kore’de siyah sarımsak, anti kanserojen özellikleri ve aroması ile yemeklerde aparatif olarak kullanılmaktadır. Amerika Birleşik Devletleri, Kanada ve İngiltere’de de yoğun şekilde ticareti başlamıştır. Bu çalışmada, siyah sarımsak konusunda yapılan araştırmaların sonuçları derlenmiştir.

  13. Analysis of three-dimensional SAR distributions emitted by mobile phones in an epidemiological perspective.

    Science.gov (United States)

    Deltour, Isabelle; Wiart, Joe; Taki, Masao; Wake, Kanako; Varsier, Nadège; Mann, Simon; Schüz, Joachim; Cardis, Elisabeth

    2011-12-01

    The three-dimensional distribution of the specific absorption rate of energy (SAR) in phantom models was analysed to detect clusters of mobile phones producing similar spatial deposition of energy in the head. The clusters' characteristics were described from the phones external features, frequency band and communication protocol. Compliance measurements with phones in cheek and tilt positions, and on the left and right side of a physical phantom were used. Phones used the Personal Digital Cellular (PDC), Code division multiple access One (CdmaOne), Global System for Mobile Communications (GSM) and Nordic Mobile Telephony (NMT) communication systems, in the 800, 900, 1500 and 1800 MHz bands. Each phone's measurements were summarised by the half-ellipsoid in which the SAR values were above half the maximum value. Cluster analysis used the Partitioning Around Medoids algorithm. The dissimilarity measure was based on the overlap of the ellipsoids, and the Manhattan distance was used for robustness analysis. Within the 800 MHz frequency band, and in part within the 900 MHz and the 1800 MHz frequency bands, weak clustering was obtained for the handset shape (bar phone, flip with top and flip with central antennas), but only in specific positions (tilt or cheek). On measurements of 120 phones, the three-dimensional distribution of SAR in phantom models did not appear to be related to particular external phone characteristics or measurement characteristics, which could be used for refining the assessment of exposure to radiofrequency energy within the brain in epidemiological studies such as the Interphone. Copyright © 2011 Wiley Periodicals, Inc.

  14. Comparisons of peak SAR levels in concentric sphere head models of children and adults for irradiation by a dipole at 900 MHz

    International Nuclear Information System (INIS)

    Anderson, Vitas

    2003-01-01

    The aim of this study is to examine the scale and significance of differences in peak specific energy absorption rate (SAR) in the brains of children and adults exposed to radiofrequency emissions from mobile phones. Estimates were obtained by method of multipole analysis of a three layered (scalp/cranium/brain) spherical head exposed to a nearby 0.4 dipole at 900 MHz. A literature review of head parameters that influence SAR induction revealed strong indirect evidence based on total body water content that there are no substantive age-related changes in tissue conductivity after the first year of life. However, it was also found that the thickness of the ear, scalp and cranium do decrease on average with decreasing age, though individual variability within any age group is very high. The model analyses revealed that compared to an average adult, the peak brain 10 g averaged SAR in mean 4, 8, 12 and 16 year olds (yo) is increased by a factor of 1.31, 1.23, 1.15 and 1.07, respectively. However, contrary to the expectations of a recent prominent expert review, the UK Stewart Report, the relatively small scale of these increases does not warrant any special precautionary measures for child mobile phone users since: (a) SAR testing protocols as contained in the CENELEC (2001) standard provide an additional safety margin which ensures that allowable localized SAR limits are not exceeded in the brain; (b) the maximum worst case brain temperature rise (∼0.13 to 0.14 degrees C for an average 4 yo) in child users of mobile phones is well within safe levels and normal physiological parameters; and (c) the range of age average increases in children is less than the expected range of variation seen within the adult population

  15. Local SAR enhancements in anatomically correct children and adult models as a function of position within 1.5 T MR body coil.

    Science.gov (United States)

    Murbach, Manuel; Cabot, Eugenia; Neufeld, Esra; Gosselin, Marie-Christine; Christ, Andreas; Pruessmann, Klaas P; Kuster, Niels

    2011-12-01

    Usage of magnetic resonance imaging (MRI) is continuously increasing due to its excellent soft-tissue contrast and improving diagnostic values. MRI also has the advantage that it operates without ionizing radiation. The main safety concerns are torque, acceleration by the static field, nerve stimulation by the gradient fields, and tissue heating by the radio-frequency (RF) fields. This paper investigates if children and fetuses are at higher risks than adults when the current RF regulations are applied. We analyzed and compared local absorption hotspots, i.e., the peak spatial specific absorption rate averaged over any 10 g (psSAR10g) for five adults, three children of ages 5, 11 and 14 years, and 1 pregnant female (36 weeks' gestation) in 10 different Z-positions (head to calves). In the First Level Operating Mode (4 W/kg whole-body averaged exposure), the psSAR10g values found for adults were as large as 60 W/kg in the trunk and 104 W/kg in the extremities. The corresponding values for children were 43 and 58 W/kg, respectively, and 14 W/kg for the unborn child. Modeling of worst case anatomical RF loops can substantially increase the psSAR10g values, i.e., by factor >2. The results suggest that local exposure for children and fetuses is smaller than for adults (15-75%), i.e., no special considerations for children and the unborn child are needed regarding psSAR10g due to RF. However, the local thermal load of the unborn may be significantly increased due to the high exposure average (up to 4 W/kg) of the non-perfused amniotic fluid. Copyright © 2011 Elsevier Ltd. All rights reserved.

  16. Measurement of the rate of hydrogen peroxide thermal decomposition in a shock tube using quantum cascade laser absorption near 7.7 μm

    KAUST Repository

    Sajid, Muhammad Bilal

    2013-10-24

    Hydrogen peroxide (H2O2) is formed during hydrocarbon combustion and controls the system reactivity under intermediate temperature conditions. Here, we measured the rate of hydrogen peroxide decomposition behind reflected shock waves using midinfrared absorption of H2O 2 near 7.7 μm. We performed the experiments in diluted H 2O2/Ar mixtures between 930 and 1235 K and at three different pressures (1, 2, and 10 atm). Under these conditions, the decay of hydrogen peroxide is sensitive only to the decomposition reaction rate, H 2O2 + M → 2OH + M (k1). The second-order rate coefficient at low pressures (1 and 2 atm) did not exhibit any pressure dependence, suggesting that the reaction was in the low-pressure limit. The rate data measured at 10 atm exhibited falloff behavior. The measured decomposition rates can be expressed in Arrhenius forms as follows: k1(1 and 2 atm)=10(16.29±0.12)× exp (-21993±301/T)(cm 3 mol -1s-1) k1(10 atm)=10(15.24±0.10)× exp (-19955±247/T)(cm 3 mol -1s-1) © 2013 Wiley Periodicals, Inc.

  17. Comparison of radio frequency energy absorption in ear and eye region of children and adults at 900, 1800 and 2450 MHz

    International Nuclear Information System (INIS)

    Keshvari, J; Lang, S

    2005-01-01

    The increasing use of mobile communication devices, especially mobile phones by children, has triggered discussions on whether there is a larger radio frequency (RF) energy absorption in the heads of children compared to that of adults. The objective of this study was to clarify possible differences in RF energy absorption in the head region of children and adults using computational techniques. Using the finite-difference time-domain (FDTD) computational method, a set of specific absorption rate (SAR) calculations were performed for anatomically correct adult and child head models. A half-wave dipole was used as an exposure source at 900, 1800 and 2450 MHz frequencies. The ear and eye regions were studied representing realistic exposure scenarios to current and upcoming mobile wireless communication devices. The differences in absorption were compared with the maximum energy absorption of the head model. Four magnetic resonance imaging (MRI) based head models, one female, one adult, two child head models, aged 3 and 7 years, were used. The head models greatly differ from each other in terms of size, external shape and the internal anatomy. The same tissue dielectric parameters were applied for all models. The analyses suggest that the SAR difference between adults and children is more likely caused by the general differences in the head anatomy and geometry of the individuals rather than age. It seems that the external shape of the head and the distribution of different tissues within the head play a significant role in the RF energy absorption

  18. Ultrasonic absorption

    International Nuclear Information System (INIS)

    Beyer, R.T.

    1985-01-01

    The paper reviews studies of ultrasonic absorption in liquid alkali metals. The experimental methods to measure the absorption coefficients are briefly described. Experimental results reported for the liquid metals: sodium, potassium, rubidium and caesium, at medium temperatures, are presented, as well as data for liquid alloys. Absorption losses due to the presence of an external magnetic field, and the effects of viscosity on the absorption in metals, are both discussed. (U.K.)

  19. Beneficial effect of somatostatin in phalloidin-intoxicated rats. Influence on survival rate, biochemical and morphological data, and 3H-demethylphalloin absorption rate by the liver.

    Science.gov (United States)

    Wdowinski, J M; Schwedes, U; Faulstich, H; Dancygier, H; Leuschner, U; Siede, W H; Hübner, K; Schöffling, K; Usadel, K H

    1981-01-01

    The effect of somatostatin in phalloidin-intoxicated rats was studied. Animals were given phalloidin i.p. 1.2 mg/kg (LD 90-100). Somatostatin, 250 microgram/animal, was administered i.p. in saline 5 min prior and s.c. in protamine-sulphate/ZnCl2 suspension 30 min prior and 30 min after intoxication, unless stated otherwise. In vivo and in vitro uptake studies of the toxin were performed. Liver enzymes (GPT, GLDH) and kallikrein-like activities were determined in blood obtained by orbital venipuncture. Light and electron microscopy was carried out. Somatostatin treatment led to an increase in survival rate. Of the 20 treated rats six died whereas of the 20 untreated animals 18 died. A dose dependency was proven effective when half of the initial dose of somatostatin was given. In vivo and in vitro uptake studies of the toxin demonstrate that somatostatin does not alter uptake rate by rat livers. Liver enzymes remained elevated in treated and control rats. Kallikrein-like activities showed a 61% decline in treated animals whereas they rose up to 120% in controls as compared to pretreatment conditions. Light and electron microscopy reveals less severe lesions in somatostatin-treated animals. A possible interaction of somatostatin in shock development is discussed, phalloidin seems to be a suitable tool for further investigations concerning cell protection by somatostatin.

  20. High-accuracy measurements of OH reaction rate constants and IR absorption spectra: CH2=CF-CF3 and trans-CHF=CH-CF3.

    Science.gov (United States)

    Orkin, Vladimir L; Martynova, Larissa E; Ilichev, Alexander N

    2010-05-20

    Rate constants for the gas phase reactions of OH radicals with two isomers of tetrafluoropropene, CH(2)=CF-CF(3) (k(1)) and trans-CHF=CH-CF(3) (k(2)); were measured using a flash photolysis resonance-fluorescence technique over the temperature range 220 to 370 K. The Arrhenius plots were found to exhibit a noticeable curvature. The temperature dependences of the rate constants are very weak and can be represented by the following expressions over the indicated temperature intervals: k(1)(220-298 K) = 1.145 x 10(-12) x exp{13/T} cm(3) molecule(-1) s(-1), k(1)(298-370 K) = 4.06 x 10(-13) x (T/298)(1.17) x exp{+296/T} cm(3) molecule(-1) s(-1), k(2)(220-370 K) = 1.115 x 10(-13) x (T/298)(2.03) x exp{+522/T} cm(3) molecule(-1) s(-1). The overall accuracy of the rate constant measurements is estimated to be ca. 2% to 2.5% at the 95% confidence level. The uncertainty of the measured reaction rate constants is discussed in detail. The atmospheric lifetimes due to reactions with tropospheric OH were estimated to be 12 and 19 days respectively under the assumption of a well mixed atmosphere. IR absorption cross-sections were measured for both compounds and their global warming potentials were estimated.

  1. Seasonal Inundation Monitoring of Northern Pantanal Wetland, Brazil Using ALOS SAR/InSAR and Envisat Altimetry

    Science.gov (United States)

    Kim, J.; Calmant, S.; Lee, H.; Lu, Z.; Shum, C.

    2011-12-01

    The Pantanal is one of the most biologically diverse ecosystems and largest wetland in the world. It has been threatened by massive economic development, and anthropogenic climate change. At the current rate, the Brazilian Pantanal will disappear within 45 years, according to 2006 report by Conservation International. Here, we illustrate that the evolutions of the Pantanal can be characterized by using ALOS PALSAR Fine-Beam and ScanSAR mode images, and Envisat radar altimetry. Multi-mode of high resolution and large-scale SAR images were used to unveil temporal and spatial inundation patterns. The backscattering coefficient of multi-mode SAR images shows regular change pattern in response to periodic inundation. InSAR analysis allows us to recognize that the temporal variation is not spatially constant, which is distinct among other wetlands, e.g., Louisiana wetlands. In addition to SAR/InSAR data, radar Altimetry (Envisat) is critical for providing vertical datum and fine temporal resolution, towards characterization of the Pantanal wetland condition during inundation. The observed close correlation between inundation area from SAR images and hydraulic change from a river gauge implies that the Pantanal is vulnerable to external effects presumably by human activities, and abnormal hydraulic change can threaten the ecosystems and biological diversity. We conclude that radar remote sensing data can provide timely and high-resolution monitoring of hydraulic characteristics of the Pantanal, one of the least-known and most fragile wetlands, and they can potentially be used as an efficient tool for remote wetland monitoring and ecological studies.

  2. Surface deformation of Taipei basin detected by Differential SAR Interferometry

    Science.gov (United States)

    Chen, Y.; Chang, C.; Yen, J.; Lin, M.

    2006-12-01

    Taiwan island is located between the southeastern periphery of the Eurasian plate and the Philippine Sea plate. The two converging plates produced very active tectonics, and can be seen by the high seismicity and deformation rate. Taipei, the highest populated area, center of politics, and economics in Taiwan, is in Taipei basin at the northern part of the island. There are several faults in and surrounding the basin, and the city is threatened with a high geological hazard potential that we should keep monitoring the crustal deformation to prevent and mitigate the disaster effect. The aims of our study is to apply the DInSAR technique to determine the surface deformation of Taipei basin area, and discussing the relation between the manifestation of deformation and the tectonically active region, Shanjiao fault. In the past few years, Differential SAR Interferometry (DInSAR) has been proved to be a powerful technique for monitoring the neotectonic activities and natural hazards. High spatial sampling rate of DInSAR technique allows studies of surface deformations with centimeter accuracy. In this area, we used ERS-1/2 SAR images acquired from 1993 to 2005 to generate 10 differential interferograms and processed the data using DIAPASON developed by CNES and SRTM global DEM.From our results, the deformation rate in Taipei is generally high in the western end of the basin along the Shanjiao fault and decrease eastward, while the subsidence center often appeared in the center of the Taipei basin. The neotectonic activity of the Shanjiao fault appeared to be insignificant by itself but it seemed to separate the subsiding basin from the surrounding areas. Further comparison between our DInSAR results and isopach of the Taipei basin revealed that the subsidence centers appeared in the interferograms did not coincide with the location where the sediments are thickest. Our results from differential interferometry will be compared to other geodetic measurements such as the

  3. A shock tube and laser absorption study of ignition delay times and OH reaction rates of ketones: 2-Butanone and 3-buten-2-one

    KAUST Repository

    Badra, Jihad

    2014-03-01

    Ketones are potential biofuel candidates and are also formed as intermediate products during the oxidation of large hydrocarbons or oxygenated fuels, such as alcohols and esters. This paper presents shock tube ignition delay times and OH reaction rates of 2-butanone (C2H5COCH3) and 3-buten-2-one (C2H3COCH3). Ignition delay measurements were carried out over temperatures of 1100-1400K, pressures of 3-6.5atm, and at equivalence ratios (F{cyrillic}) of 0.5 and 1. Ignition delay times were monitored using two different techniques: pressure time history and OH absorption near 306nm. The reaction rates of hydroxyl radicals (OH) with these two ketones were measured over the temperature range of 950-1400K near 1.5atm. The OH profiles were monitored by the narrow-line-width ring-dye laser absorption of the well-characterized R1(5) line in the OH A-X (0, 0) band near 306.69nm. We found that the ignition delay times of 2-butanone and 3-buten-2-one mixtures scale with pressure as P-0.42 and P-0.52, respectively. The ignition delay times of 3-buten-2-one were longer than that of 2-butanone for stoichiometric mixtures, however, for lean mixtures (F{cyrillic}=0.5), 2-butanone had longer ignition delay times. The chemical kinetic mechanism of Serinyel et al. [1] over-predicted the ignition delay times of 2-butanone at all tested conditions, however, the discrepancies were smaller at higher pressures. The mechanism was updated with recent rate measurements to decrease discrepancy with the experimental data. A detailed chemistry for the oxidation of 3-buten-2-one was developed using rate estimation method and reasonable agreements were obtained with the measured ignition delay data. The measured reaction rate of 2-butanone with OH agreed well with the literature data, while we present the first high-temperature measurements for the reaction of OH with 3-buten-2-one. The following Arrhenius expressions are suggested over the temperature range of 950-1450K: kC2H5COCH3+OH=6.78×1013exp

  4. Novel Polarimetric SAR Interferometry Algorithms, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Polarimetric radar interferometry (PolInSAR) is a new SAR imaging mode that is rapidly becoming an important technique for bare earth topographic mapping, tree...

  5. SAR Image Enhancement using Particle Filters

    Data.gov (United States)

    National Aeronautics and Space Administration — In this paper, we propose a novel approach to reduce the noise in Synthetic Aperture Radar (SAR) images using particle filters. Interpretation of SAR images is a...

  6. Marine Targets Classification in PolInSAR Data

    Science.gov (United States)

    Chen, Peng; Yang, Jingsong; Ren, Lin

    2014-11-01

    In this paper, marine stationary targets and moving targets are studied by Pol-In-SAR data of Radarsat-2. A new method of stationary targets detection is proposed. The method get the correlation coefficient image of the In-SAR data, and using the histogram of correlation coefficient image. Then, A Constant False Alarm Rate (CFAR) algorithm and The Probabilistic Neural Network model are imported to detect stationary targets. To find the moving targets, Azimuth Ambiguity is show as an important feature. We use the length of azimuth ambiguity to get the target's moving direction and speed. Make further efforts, Targets classification is studied by rebuild the surface elevation of marine targets.

  7. Absorption of folic acid and its rate of disappearance from the blood of patients receiving barbiturates in excess in combination with alcohol

    International Nuclear Information System (INIS)

    Gyftaki, H.; Kesse-Elias, M.; Alevizou-Terzaki, V.; Rapidis, P.; Sdougou-Christakopoulou, J.

    1975-01-01

    It is known that megaloblastic anaemia may occur from the intake of phenobarbital, which apparently responds to folic acid and vitamin B 12 . Its site of action is not known but there is evidence that it may act as a pyrimidine antagonist. It is also known that alcoholics with or without cirrhosis have folate deficiency. Furthermore, although potentiating effects of alcohol and barbiturates exist it is not known how the combination of barbiturates and alcohol acts on folic acid metabolism. In thirty patients receiving barbiturates in excess in combination with alcohol, absorption of folic acid and its rate of disappearance were studied in the blood. Two series of studies were performed. In the first, folic acid (15μg/kg of body weight) was administered orally and the maximum concentration in the blood as well as its disappearance rate were determined. In the second, folinic acid (15 μg/kg of body weight) was administered intramuscularly and the disappearance rate of folic acid was again determined. Blood samples were taken at certain intervals after administration of folic or folinic acid. Estimation of serum folic acid level was obtained by a competitive protein-binding technique developed in our laboratory. The results are discussed and compared with those in normal subjects. (author)

  8. Segment-based change detection for polarimetric SAR data

    DEFF Research Database (Denmark)

    Skriver, Henning; Nielsen, Allan Aasbjerg; Conradsen, Knut

    2006-01-01

    single-channel SAR images but multi-channel algorithms have also been described. Different approaches have been used for image segmentation. Edge detection combined with region growing is one approach, where segments are created by growing regions from a previously edge detected and edge thinned image....... This method relies primarily on a robust edge detector, which preferably provides a constant false alarm rate. For single-channel SAR images this is fulfilled by the ratio edge detector, and for polarimetric SAR data, an edge detector based on the above mentioned test statistic fulfils this. Another approach......, wetlands, lakes, and urban areas. Also, other test sites over for instance urban areas have been used to assess the improvement by the segment-based change detection method. In the paper, results from pixel-based change detection, i.e. without segmentation, and from segment-based change detection, where...

  9. Imaging in severe acute respiratory syndrome (SARS)

    International Nuclear Information System (INIS)

    Antonio, G.E.; Wong, K.T.; Chu, W.C.W.; Hui, D.S.C.; Cheng, F.W.T.; Yuen, E.H.Y.; Chung, S.S.C.; Fok, T.F.; Sung, J.J.Y.; Ahuja, A.T.

    2003-01-01

    Severe acute respiratory syndrome (SARS) is a highly infectious disease caused by a novel coronavirus, and has become pandemic within a short period of time. Imaging plays an important role in the diagnosis, management and follow-up of patients with SARS. The current status of imaging in SARS is presented in this review

  10. SAR Systems and Related Signal Processing

    NARCIS (Netherlands)

    Hoogeboom, P.; Dekker, R.J.; Otten, M.P.G.

    1996-01-01

    Synthetic Aperture Radar (SAR) is today a valuable source of remote sensing information. SAR is a side-looking imaging radar and operates from airborne and spacebome platforms. Coverage, resolution and image quality are strongly influenced by the platform. SAR processing can be performed on standard

  11. Convolutional Neural Networks for SAR Image Segmentation

    DEFF Research Database (Denmark)

    Malmgren-Hansen, David; Nobel-Jørgensen, Morten

    2015-01-01

    Segmentation of Synthetic Aperture Radar (SAR) images has several uses, but it is a difficult task due to a number of properties related to SAR images. In this article we show how Convolutional Neural Networks (CNNs) can easily be trained for SAR image segmentation with good results. Besides...

  12. Measuring the Absorption Rate of CO 2 in Nonaqueous CO 2 -Binding Organic Liquid Solvents with a Wetted-Wall Apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Mathias, Paul M. [Process Technology, Fluor Corporation, 3 Polaris Way Aliso Viejo CA 92698 USA; Zheng, Feng [Energy and Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99352 USA; Heldebrant, David J. [Energy and Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99352 USA; Zwoster, Andy [Energy and Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99352 USA; Whyatt, Greg [Energy and Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99352 USA; Freeman, Charles M. [Energy and Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99352 USA; Bearden, Mark D. [Energy and Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99352 USA; Koech, Phillip [Energy and Environment Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99352 USA

    2015-09-17

    The kinetics of the absorption of CO2 into two nonaqueous CO2-binding organic liquid (CO2BOL) solvents were measured at T=35, 45, and 55 °C with a wetted-wall column. Selected CO2 loadings were run with a so-called “first-generation” CO2BOL, comprising an independent base and alcohol, and a “second-generation” CO2BOL, in which the base and alcohol were conjoined. Liquid-film mass-transfer coefficient (k'g) values for both solvents were measured to be comparable to values for monoethanolamine and piperazine aqueous solvents under a comparable driving force, in spite of far higher solution viscosities. An inverse temperature dependence of the k'g value was also observed, which suggests that the physical solubility of CO2 in organic liquids may be making CO2 mass transfer faster than expected. Aspen Plus software was used to model the kinetic data and compare the CO2 absorption behavior of nonaqueous solvents with that of aqueous solvent platforms. This work continues our development of the CO2BOL solvents. Previous work established the thermodynamic properties related to CO2 capture. The present paper quantitatively studies the kinetics of CO2 capture and develops a rate-based model.

  13. Monitoring of Land-Surface Deformation in the Karamay Oilfield, Xinjiang, China, Using SAR Interferometry

    Directory of Open Access Journals (Sweden)

    Yusupujiang Aimaiti

    2017-07-01

    Full Text Available Synthetic Aperture Radar (SAR interferometry is a technique that provides high-resolution measurements of the ground displacement associated with various geophysical processes. To investigate the land-surface deformation in Karamay, a typical oil-producing city in the Xinjiang Uyghur Autonomous Region, China, Advanced Land Observing Satellite (ALOS Phased Array L-band Synthetic Aperture Radar (PALSAR data were acquired for the period from 2007 to 2009, and a two-pass differential SAR interferometry (D-InSAR process was applied. The experimental results showed that two sites in the north-eastern part of the city exhibit a clear indication of land deformation. For a further evaluation of the D-InSAR result, the Persistent Scatterer (PS and Small Baseline Subset (SBAS-InSAR techniques were applied for 21 time series Environmental Satellite (ENVISAT C-band Advanced Synthetic Aperture Radar (ASAR data from 2003 to 2010. The comparison between the D-InSAR and SBAS-InSAR measurements had better agreement than that from the PS-InSAR measurement. The maximum deformation rate attributed to subsurface water injection for the period from 2003 to 2010 was up to approximately 33 mm/year in the line of sight (LOS direction. The interferometric phase change from November 2007 to June 2010 showed a clear deformation pattern, and the rebound center has been expanding in scale and increasing in quantity.

  14. How change of public transportation usage reveals fear of the SARS virus in a city.

    Directory of Open Access Journals (Sweden)

    Kuo-Ying Wang

    Full Text Available The outbreaks of the severe acute respiratory syndrome (SARS epidemic in 2003 resulted in unprecedented impacts on people's daily life. One of the most significant impacts to people is the fear of contacting the SARS virus while engaging daily routine activity. Here we use data from daily underground ridership in Taipei City and daily reported new SARS cases in Taiwan to model the dynamics of the public fear of the SARS virus during the wax and wane of the SARS period. We found that for each reported new SARS case there is an immediate loss of about 1200 underground ridership (the fresh fear. These daily loss rates dissipate to the following days with an e-folding time of about 28 days, reflecting the public perception on the risk of contacting SARS virus when traveling with the underground system (the residual fear. About 50% of daily ridership was lost during the peak of the 2003 SARS period, compared with the loss of 80% daily ridership during the closure of the underground system after Typhoon Nari, the loss of 50-70% ridership due to the closure of the governmental offices and schools during typhoon periods, and the loss of 60% daily ridership during Chinese New Year holidays.

  15. How change of public transportation usage reveals fear of the SARS virus in a city.

    Science.gov (United States)

    Wang, Kuo-Ying

    2014-01-01

    The outbreaks of the severe acute respiratory syndrome (SARS) epidemic in 2003 resulted in unprecedented impacts on people's daily life. One of the most significant impacts to people is the fear of contacting the SARS virus while engaging daily routine activity. Here we use data from daily underground ridership in Taipei City and daily reported new SARS cases in Taiwan to model the dynamics of the public fear of the SARS virus during the wax and wane of the SARS period. We found that for each reported new SARS case there is an immediate loss of about 1200 underground ridership (the fresh fear). These daily loss rates dissipate to the following days with an e-folding time of about 28 days, reflecting the public perception on the risk of contacting SARS virus when traveling with the underground system (the residual fear). About 50% of daily ridership was lost during the peak of the 2003 SARS period, compared with the loss of 80% daily ridership during the closure of the underground system after Typhoon Nari, the loss of 50-70% ridership due to the closure of the governmental offices and schools during typhoon periods, and the loss of 60% daily ridership during Chinese New Year holidays.

  16. A study of the exposure of subjects to RF radiation during MRI examinations. Measurement of the SAR of head parts and the evaluation of the measured values

    International Nuclear Information System (INIS)

    Yamada, Masayuki; Koga, Sukehiko; Sugie, Masami; Kinoshita, Kazuo; Anno, Hirofumi; Katada, Kazuhiro.

    1996-01-01

    Recently, as the fast spin echo technique has become prevailing among all the techniques in this line, there has been an increasing interest in the exposure of subjects to radiofrequency (RF) radiation during magnetic resonance imaging (MRI) examinations. On the other hand, there have been no reports about the safety of the MRI examination in Japan. For this reason, in this study, the authors aimed to evaluate the extent of the exposure of subjects to RF radiation during MRI examinations, and measured the specific absorption rate (SAR) of spherical phantoms, which assumed to be adult heads, by using the procedures set forth in two safety guidelines respectively: the 1988 Guideline of the Food and Drug Administration (FDA), and the 1995 Standards of the International Electrotechnical Commission (IEC). As a result of the measurement, it was found that the highest value of the SAR was 1.361 W/kg, which stayed far below the upper limits set forth by the respective safety guidelines referred to in the above. However, the measured values of the SAR varied depending on the respective measuring procedures. As both the measuring procedures are equivalent theoretically, the authors consider the variance to be very important. (author)

  17. Polarimetric scattering and SAR information retrieval

    CERN Document Server

    Jin, Ya-Qiu

    2013-01-01

    Taking an innovative look at Synthetic Aperture Radar (SAR), this practical reference fully covers new developments in SAR and its various methodologies and enables readers to interpret SAR imagery An essential reference on polarimetric Synthetic Aperture Radar (SAR), this book uses scattering theory and radiative transfer theory as a basis for its treatment of topics. It is organized to include theoretical scattering models and SAR data analysis techniques, and presents cutting-edge research on theoretical modelling of terrain surface. The book includes quantitative app

  18. SARS – virus jumps species

    Indian Academy of Sciences (India)

    SARS – virus jumps species. Coronavirus reshuffles genes; Rotteir et al, Rotterdam showed the virus to jump from cats to mouse cells after single gene mutation ? Human disease due to virus jumping from wild or domestic animals; Present favourite animal - the cat; - edible or domestic.

  19. Stalking SARS: CDC at Work

    Centers for Disease Control (CDC) Podcasts

    2014-05-22

    In this podcast for kids, the Kidtastics talk about the SARS outbreak and how CDC worked to solve the mystery.  Created: 5/22/2014 by National Center for Immunization and Respiratory Diseases (NCIRD).   Date Released: 5/22/2014.

  20. Light weight digital array SAR

    NARCIS (Netherlands)

    Otten, M.; Maas, N.; Bolt, R.; Anitori, L.

    2010-01-01

    A light weight SAR has been designed, suitable for short range tactical UAVs, consisting of a fully digital receive array, and a very compact active transmit antenna. The weight of the complete RF front is expected to be below 3 kg, with a power consumption below 30 W. This X-band system can provide

  1. Topography estimation using SAR image polarimetry

    Science.gov (United States)

    Sabry, Ramin; Mattar, Karim E.

    2014-10-01

    Polarization orientation angle (POA) correction to compensate for terrain effects on polarimetric SAR data has been investigated in the literature. POA rotation can be derived from digital elevation model (DEM) and/or from polarimetric SAR (PolSAR) data through covariance/coherency analysis. A robust analytic model connecting PolSAR data and products (e.g., POA) to target/scene terrain characteristics can serve two main objectives. First is to correct and calibrate PolSAR data acquired from different SARs when DEM is available. Second is to model terrain through inverse solution of POAs derived from PolSAR data analysis. This formalism has been developed and is presented here. Effectiveness of the technique in providing both forward (POAs from DEM) and inverse (DEM from POAs) solutions is explored through imagery product examples and simulations.

  2. Effect of Microenvironmental pH Modulation on the Dissolution Rate and Oral Absorption of the Salt of a Weak Acid - Case Study of GDC-0810.

    Science.gov (United States)

    Hou, Hao Helen; Jia, Wei; Liu, Lichuan; Cheeti, Sravanthi; Li, Jane; Nauka, Ewa; Nagapudi, Karthik

    2018-01-29

    The purpose of this work is to investigate the effect of microenvironmental pH modulation on the in vitro dissolution rate and oral absorption of GDC-0810, an oral anti-cancer drug, in human. The pH-solubility profile of GDC-0810 free acid and pH max of its N-Methyl-D-glucamine (NMG) salt were determined. Precipitation studies were conducted for GDC-0810 NMG salt at different pH values. GDC-0810 200-mg dose NMG salt tablet formulations containing different levels of sodium bicarbonate as the pH modifier were tested for dissolution under the dual pH-dilution scheme. Three tablet formulations were evaluated in human as a part of a relative bioavailability study. A 200-mg dose of GDC-0810 was administered QD with low fat food. Intrinsic solubility of GDC-0810 free acid was found to be extremely low. The pH max of the NMG salt suggested a strong tendency for form conversion to the free acid under GI conditions. In vitro dissolution profiles showed that the dissolution rate and extent of GDC-0810 increased with increasing the level of sodium bicarbonate in the formulation. The human PK data showed a similar trend for the geometric mean of C max and AUC 0-t for formulations containing 5%, 10%, and 15% sodium bicarbonate, but the difference is not statistically significant. Incorporation of a basic pH modifier, sodium bicarbonate, in GDC-0810 NMG salt tablet formulations enhanced in vitro dissolution rate of GDC-0810 via microenvironmental pH modulation. The human PK data showed no statistically significant difference in drug exposure from tablets containing 5%, 10%, and 15% sodium bicarbonate.

  3. Absorption studies

    International Nuclear Information System (INIS)

    Ganatra, R.D.

    1992-01-01

    Absorption studies were once quite popular but hardly anyone does them these days. It is easier to estimate the blood level of the nutrient directly by radioimmunoassay (RIA). However, the information obtained by estimating the blood levels of the nutrients is not the same that can be obtained from the absorption studies. Absorption studies are primarily done to find out whether some of the essential nutrients are absorbed from the gut or not and if they are absorbed, to determine how much is being absorbed. In the advanced countries, these tests were mostly done to detect pernicious anaemia where vitamin B 12 is not absorbed because of the lack of the intrinsic factor in the stomach. In the tropical countries, ''malabsorption syndrome'' is quire common. In this condition, several nutrients like fat, folic acid and vitamin B 12 are not absorbed. It is possible to study absorption of these nutrients by radioisotopic absorption studies

  4. Risk factors for SARS transmission from patients requiring intubation: a multicentre investigation in Toronto, Canada.

    Directory of Open Access Journals (Sweden)

    Janet Raboud

    to respiratory secretions were associated with transmission of SARS-CoV. Rates of transmission of SARS-CoV varied widely among patients.

  5. hPEPT1 Affinity and Translocation of Selected Gln-Sar and Glu-Sar Dipeptide Derivatives

    DEFF Research Database (Denmark)

    Eriksson, A. H.; Elm, Peter L.; Begtrup, Mikael

    2005-01-01

    The intestinal di- and tripeptide transporter hPEPT1 is considered responsible for the absorption of di- and tripeptides arising from digestion, along with several drugs and prodrugs. In order to gather information on the binding site of the protein, several structure-affinity relationships have......, hydrophobicity, and bond type. The aim of the present study was to synthesize new esters and amides based on l-Glu-Sar and investigate the effects that bond type and size of modification of the N-terminal side chain of sarcosine-containing dipeptides have on the affinity to and translocation via hPEPT1...

  6. Folate absorption

    International Nuclear Information System (INIS)

    Baker, S.J.

    1976-01-01

    Folate is the generic term given to numerous compounds of pteroic acid with glutamic acid. Knowledge of absorption is limited because of the complexities introduced by the variety of compounds and because of the inadequacy of investigational methods. Two assay methods are in use, namely microbiological and radioactive. Techniques used to study absorption include measurement of urinary excretion, serum concentration, faecal excretion, intestinal perfusion, and haematological response. It is probably necessary to test absorption of both pteroylmonoglutamic acid and one or more polyglutamates, and such tests would be facilitated by availability of synthesized compounds labelled with radioactive tracers at specifically selected sites. (author)

  7. Prediction and comparison of down-link electric field and uplink localised SAR values for realistic indoor wireless planning

    International Nuclear Information System (INIS)

    Plets, David; Joseph, Wout; Aerts, Sam; Vanhecke, Kris; Vermeeren, Guenter; Martens, Luc

    2014-01-01

    In this paper, for the first time a heuristic network calculator for both whole-body exposure due to indoor base station antennas or access points (down-link exposure) and localised exposure due to the mobile device (uplink exposure) in indoor wireless networks is presented. As an application, three phone call scenarios are investigated (Universal Mobile Telecommunications System (UMTS) macro-cell, UMTS femto-cell and WiFi voice-over-IP) and compared with respect to the electric-field strength and localised specific absorption rate (SAR) distribution. Prediction models are created and successfully validated with an accuracy of 3 dB. The benefits of the UMTS power control mechanisms are demonstrated. However, dependent on the macro-cell connection quality and on the user's average phone call connection time, also the macro-cell solution might be preferential from an exposure point of view for the considered scenario. (authors)

  8. Rating

    OpenAIRE

    Karas, Vladimír

    2006-01-01

    Charakteristika ratingu. Dělení a druhy ratingu (rating emise × rating emitenta; dlouhodobý rating × krátkodobý rating; mezinárodní rating × lokální rating). Obecné požadavky kladené na rating. Proces tvorby ratingu. Vyžádaný rating. Nevyžádaný rating. Ratingový proces na bázi volně přístupných informací. Uplatňované ratingové systémy. Ratingová kriteria. Využití a interpretace ratingové známky. Funkce ratingu. Rating v souvislosti s BASEL II. Rating v souvislosti s hospodářskými krizemi....

  9. Synthetic SAR Image Generation using Sensor, Terrain and Target Models

    DEFF Research Database (Denmark)

    Kusk, Anders; Abulaitijiang, Adili; Dall, Jørgen

    2016-01-01

    of the object using a CAD-model. The raw measurements are input to a SAR system and terrain model, which models thermal noise, terrain clutter, and SAR focusing to produce synthetic SAR images. Examples of SAR images at 0.3m and 0.1m resolution, and a comparison with real SAR imagery from the MSTAR dataset...

  10. Narrative absorption

    DEFF Research Database (Denmark)

    Narrative Absorption brings together research from the social sciences and Humanities to solve a number of mysteries: Most of us will have had those moments, of being totally absorbed in a book, a movie, or computer game. Typically we do not have any idea about how we ended up in such a state. Nor...... do we fully realize how we might have changed as we return for the fictional worlds we have visited. The feeling of being absorbed is one of the most illusive and transient feelings, but also one that motivates audiences to spend considerable amounts of time in narrative worlds, and one...... that is central to our understanding of the effects of narratives on beliefs and behavior. Key specialists inform the reader of this book about the nature of the peculiar state of consciousness during episodes of absorption, the perception of absorption in history, the role of absorption in meaningful experiences...

  11. Large scale study on the variation of RF energy absorption in the head and brain regions of adults and children and evaluation of the SAM phantom conservativeness

    International Nuclear Information System (INIS)

    Keshvari, J; Kivento, M; Christ, A; Bit-Babik, G

    2016-01-01

    This paper presents the results of two computational large scale studies using highly realistic exposure scenarios, MRI based human head and hand models, and two mobile phone models. The objectives are (i) to study the relevance of age when people are exposed to RF by comparing adult and child heads and (ii) to analyze and discuss the conservativeness of the SAM phantom for all age groups. Representative use conditions were simulated using detailed CAD models of two mobile phones operating between 900 MHz and 1950 MHz including configurations with the hand holding the phone, which were not considered in most previous studies. The peak spatial-average specific absorption rate (psSAR) in the head and the pinna tissues is assessed using anatomically accurate head and hand models. The first of the two mentioned studies involved nine head-, four hand- and two phone-models, the second study included six head-, four hand- and three simplified phone-models (over 400 configurations in total). In addition, both studies also evaluated the exposure using the SAM phantom. Results show no systematic differences between psSAR induced in the adult and child heads. The exposure level and its variation for different age groups may be different for particular phones, but no correlation between psSAR and model age was found. The psSAR from all exposure conditions was compared to the corresponding configurations using SAM, which was found to be conservative in the large majority of cases. (paper)

  12. A Novel Cellular Handset Design for an Enhanced Antenna Performance and a Reduced SAR in the Human Head

    Directory of Open Access Journals (Sweden)

    Salah I. Al-Mously

    2008-01-01

    Full Text Available This paper presents a novel cellular handset design with a bottom-mounted short loaded-whip antenna. This new handset design is modeled and simulated using a finite difference time-domain (FDTD-based platform SEMCAD. The proposed handset is based on a current commercially available bar-phone type with a curvature shape, keypad positioned above the screen, and top-mounted antenna. The specific absorption rates (SARs are determined computationally in the specific anthropomorphic mannequin (SAM and anatomically correct model of a human head when exposed to the EM-field radiation of the proposed cellular handset and the handset with top-mounted antenna. The two cellular handsets are simulated to operate at both GSM standards, 900 MHz as well as 1800 MHz, having different antenna dimensions and intput power of 0.6 W and 0.125 W, respectively. The proposed human hand holding the two handset models is a semirealistic hand model consists of three tissues: skin, muscle, and bone. The simulations are conducted with handset positions based on the IEEE standard 1528-2003. The results show that the proposed handset has a significant improvement of antenna efficiency when it is hand-held close to head, as compared with the handset of top-mounted antenna. Also, the results show that a significant reduction of the induced SAR in the human head-tissues can be achieved with the proposed handset.

  13. SAR Image Complex Pixel Representations

    Energy Technology Data Exchange (ETDEWEB)

    Doerry, Armin W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-03-01

    Complex pixel values for Synthetic Aperture Radar (SAR) images of uniform distributed clutter can be represented as either real/imaginary (also known as I/Q) values, or as Magnitude/Phase values. Generally, these component values are integers with limited number of bits. For clutter energy well below full-scale, Magnitude/Phase offers lower quantization noise than I/Q representation. Further improvement can be had with companding of the Magnitude value.

  14. Building Detection in SAR Imagery

    Energy Technology Data Exchange (ETDEWEB)

    Steinbach, Ryan Matthew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Koch, Mark William [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Moya, Mary M [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Goold, Jeremy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-08-01

    Current techniques for building detection in Synthetic Aperture Radar (SAR) imagery can be computationally expensive and/or enforce stringent requirements for data acquisition. The desire is to present a technique that is effective and efficient at determining an approximate building location. This approximate location can be used to extract a portion of the SAR image to then perform a more robust detection. The proposed technique assumes that for the desired image, bright lines and shadows, SAR artifact effects, are approximately labeled. These labels are enhanced and utilized to locate buildings, only if the related bright lines and shadows can be grouped. In order to find which of the bright lines and shadows are related, all of the bright lines are connected to all of the shadows. This allows the problem to be solved from a connected graph viewpoint. Where the nodes are the bright lines and shadows and the arcs are the connections between bright lines and shadows. Constraints based on angle of depression and the relationship between connected bright lines and shadows are applied to remove unrelated arcs. Once the related bright lines and shadows are grouped, their locations are combined to provide an approximate building location. Experimental results are provided showing the outcome of the technique.

  15. Forest biomass estimation from polarimetric SAR interferometry

    Energy Technology Data Exchange (ETDEWEB)

    Mette, T.

    2007-07-01

    Polarimetric SAR interferometry (Pol-InSAR) is a radar remote sensing technique that allows extracting forest heights by means of model-based inversions. Forest biomass is closely related to forest height, and can be derived from it with allometric relations. This work investigates the combination of the two methods to estimate forest biomass from Pol-InSAR. It develops a concept for the use of height-biomass allometry, and outlines the Pol-InSAR height inversion. The methodology is validated against a set of forest inventory data and Pol-InSAR data at L-band of the test site Traunstein. The results allow drawing conclusions on the potential of Pol-InSAR forest biomass missions. (orig.)

  16. Compressive strength and initial water absorption rate for cement brick containing high-density polyethylene (HDPE) as a substitutional material for sand

    Science.gov (United States)

    Ali, Noorwirdawati; Din, Norhasmiza; Sheikh Khalid, Faisal; Shahidan, Shahiron; Radziah Abdullah, Siti; Samad, Abdul Aziz Abdul; Mohamad, Noridah

    2017-11-01

    The rapid growth of today’s construction sector requires high amount of building materials. Bricks, known to have solid properties and easy to handle, which leads to the variety of materials added or replaced in its mixture. In this study, high density polyethylene (HDPE) was selected as the substitute materials in the making of bricks. The reason behind the use of HDPE is because of its recyclable properties and the recycling process that do not emit hazardous gases to the atmosphere. Other than that, the use of HDPE will help reducing the source of pollution by avoiding the millions of accumulated plastic waste in the disposal sites. Furthermore, the material has high endurance level and is weatherproof. This study was carried out on experimenting the substitute materials in the mixture of cement bricks, a component of building materials which is normally manufactured using the mixture of cement, sand and water, following a certain ratios, and left dried to produce blocks of bricks. A series of three different percentages of HDPE were used, which were 2.5%, 3.0% and 3.5%. Tests were done on the bricks, to study its compressive strength and the initial water absorption rate. Both tests were conducted on the seventh and 28th day. Based on the results acquired, for compressive strength tests on the 28th day, the use of 2.5% of HDPE shown values of 12.6 N/mm2 while the use of 3.0% of HDPE shown values of 12.5 N/mm2. Onto the next percentage, 3.5% of HDPE shown values of 12.5 N/mm2.

  17. Antigen Production in Plant to Tackle Infectious Diseases Flare Up: the Case of SARS

    Directory of Open Access Journals (Sweden)

    Olivia C eDemurtas

    2016-02-01

    Full Text Available Severe Acute Respiratory Syndrome (SARS is a dangerous infection with pandemic potential. It emerged in 2002 and its aetiological agent, the SARS Coronavirus (SARS-CoV, crossed the species barrier to infect humans, showing high morbidity and mortality rates. No vaccines are currently licensed for SARS-CoV and important efforts have been performed during the first outbreak to develop diagnostic tools. Here we demonstrate the transient expression in Nicotiana benthamiana of two important antigenic determinants of the SARS-CoV, the nucleocapsid protein (N and the membrane protein (M using a virus-derived vector or agro-infiltration, respectively. For the M protein, this is the first description of production in plants, while for plant-derived N protein we demonstrate that it is recognized by sera of patients from the SARS outbreak in Hong Kong in 2003. The availability of recombinant N and M proteins from plants opens the way to further evaluation of their potential utility for the development of diagnostic and protection/therapy tools to be quickly manufactured, at low cost and with minimal risk, to face potential new highly infectious SARS-CoV outbreaks.

  18. Absorption fluids data survey

    Science.gov (United States)

    Macriss, R. A.; Zawacki, T. S.

    Development of improved data for the thermodynamic, transport and physical properties of absorption fluids were studied. A specific objective of this phase of the study is to compile, catalog and coarse screen the available US data of known absorption fluid systems and publish it as a first edition document to be distributed to manufacturers, researchers and others active in absorption heat pump activities. The methodology and findings of the compilation, cataloguing and coarse screening of the available US data on absorption fluid properties and presents current status and future work on this project are summarized. Both in house file and literature searches were undertaken to obtain available US publications with pertinent physical, thermodynamic and transport properties data for absorption fluids. Cross checks of literature searches were also made, using available published bibliographies and literature review articles, to eliminate secondary sources for the data and include only original sources and manuscripts. The properties of these fluids relate to the liquid and/or vapor state, as encountered in normal operation of absorption equipment employing such fluids, and to the crystallization boundary of the liquid phase, where applicable. The actual data were systematically classified according to the type of fluid and property, as well as temperature, pressure and concentration ranges over which data were available. Data were sought for 14 different properties: Vapor-Liquid Equilibria, Crystallization Temperature, Corrosion Characteristics, Heat of Mixing, Liquid-Phase-Densities, Vapor-Liquid-Phase Enthalpies, Specific Heat, Stability, Viscosity, Mass Transfer Rate, Heat Transfer Rate, Thermal Conductivity, Flammability, and Toxicity.

  19. Experimental investigation and histopathological identification of acute thermal damage in skeletal porcine muscle in relation to whole-body SAR, maximum temperature, and CEM43 °C due to RF irradiation in an MR body coil of birdcage type at 123 MHz.

    Science.gov (United States)

    Nadobny, Jacek; Klopfleisch, Robert; Brinker, Gerhard; Stoltenburg-Didinger, Gisela

    2015-06-01

    This study is an investigation of the relationship between several characteristic parameters and acute thermal damage in porcine skeletal muscle. Fourteen pigs under injection anaesthesia were placed into a magnetic resonance body coil and exposed for different time durations to different specific energy absorption rate (SAR) levels at 123 MHz. Local temperatures were measured using four temperature sensors. Sensors 1-3 were placed in skeletal muscle and one sensor was placed in the rectum. Sensors 1 and 2 were placed in hot-spot areas and sensor 3 was placed at the periphery of the animals. The pigs were exposed to whole-body SAR (SAR-wb) between 2.5 W/kg and 5.2 W/kg for 30 or 60 min. Three animals received no SAR. After each experiment, muscle samples adjacent to the positions of sensors 1-3 were taken for frozen section analysis. Three characteristic parameters were chosen for investigation: SAR-wb, maximum sensor temperature (T-max), and cumulative equivalent minutes at 43 °C (CEM43 °C). Histopathological criteria were established to detect acute thermal tissue damage in frozen sections such as widening of intercellular space between the muscle fibres and loss of glycogen. Clear tissue damage thresholds were found for T-max and CEM43 °C, though not for SAR-wb. For all animals with high thermal exposure, damage was also found for muscle samples adjacent to the peripheral sensor 3. Both T-max and CEM43, are able to predict thermal damage in porcine muscle. However, CEM43 is the less ambiguous parameter. The reasons for the occurrence of the aforementioned damage at low local temperatures at the animals' periphery remain unclear and further investigations are needed.

  20. Precision Rectification of Airborne SAR Image

    DEFF Research Database (Denmark)

    Dall, Jørgen; Liao, M.; Zhang, Zhe

    1997-01-01

    A simple and direct procedure for the rectification of a certain class of airborne SAR data is presented. The relief displacements of SAR data are effectively removed by means of a digital elevation model and the image is transformed to the ground coordinate system. SAR data from the Danish EMISAR......([7]) is used. The EMISAR produces data with a geometrical resolution of 2.0 meters. The corrected image is tested against photogrammetric control measurements and an accuracy better than 0.5 pixel corresponding to 0.75 meters is obtained. The results indicate promising possibilities...... for the application of SAR data in the difficult process of map revision and updating....

  1. Bistatic SAR: Signal Processing and Image Formation.

    Energy Technology Data Exchange (ETDEWEB)

    Wahl, Daniel E.; Yocky, David A.

    2014-10-01

    This report describes the significant processing steps that were used to take the raw recorded digitized signals from the bistatic synthetic aperture RADAR (SAR) hardware built for the NCNS Bistatic SAR project to a final bistatic SAR image. In general, the process steps herein are applicable to bistatic SAR signals that include the direct-path signal and the reflected signal. The steps include preprocessing steps, data extraction to for a phase history, and finally, image format. Various plots and values will be shown at most steps to illustrate the processing for a bistatic COSMO SkyMed collection gathered on June 10, 2013 on Kirtland Air Force Base, New Mexico.

  2. Geometric calibration of ERS satellite SAR images

    DEFF Research Database (Denmark)

    Mohr, Johan Jacob; Madsen, Søren Nørvang

    2001-01-01

    Geometric calibration of the European Remote Sensing (ERS) Satellite synthetic aperture radar (SAR) slant range images is important in relation to mapping areas without ground reference points and also in relation to automated processing. The relevant SAR system parameters are discussed and calib......Geometric calibration of the European Remote Sensing (ERS) Satellite synthetic aperture radar (SAR) slant range images is important in relation to mapping areas without ground reference points and also in relation to automated processing. The relevant SAR system parameters are discussed...

  3. In vitro hyperthermia with improved colloidal stability and enhanced SAR of magnetic core/shell nanostructures.

    Science.gov (United States)

    Patil, R M; Thorat, N D; Shete, P B; Otari, S V; Tiwale, B M; Pawar, S H

    2016-02-01

    Magnetic core/shell nanostructures of Fe3O4 nanoparticles coated with oleic acid and betaine-HCl were studied for their possible use in magnetic fluid hyperthermia (MFH). Their colloidal stability and heat induction ability were studied in different media viz. phosphate buffer solution (PBS), saline solution and glucose solution with different physiological conditions and in human serum. The results showed enhanced colloidal stability in these media owing to their high zeta potential values. Heat induction studies showed that specific absorption rates (SAR) of core/shells were 82-94W/g at different pH of PBS and concentrations of NaCl and glucose. Interestingly, core/shells showed 78.45±3.90W/g SAR in human serum. The cytotoxicity of core/shells done on L929 and HeLa cell lines using 3-(4,5-dimethylthiazol-2-yl)2,5-diphenyl tetrazolium bromide and trypan blue dye exclusion assays showed >89% and >80% cell viability for 24 and 48h respectively. Core/shell structures were also found to be very efficient for in vitro MFH on cancer cell line. About 95% cell death was occurred in 90min after hyperthermia treatment. The mechanism of cell death was found to be elevated ROS generation in cells after exposure to core/shells in external magnetic field. This study showed that these core/shells have a great potential to be used in in vivo MFH. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. InfoTerra/TerraSAR initiative

    Science.gov (United States)

    Wahl, Manfred W.

    2004-01-01

    The overarching goal of the InfoTerra/TerraSAR Initiative is to establish a self-sustaining operational/commercial business built on Europe"s know-how and experience in space-borne Synthetic Aperture Radar (SAR) technology, in SAR data processing as well as in SAR applications. InfoTerra stands for a new business concept based on supplying innovative geo-information products and services. TerraSAR is a space and ground system conceived to consist of an initial deployment and operation of 2 Radar satellites (one in X- and one in L-band) flying in a tandem configuration in the same orbit. The design of TerraSAR is driven by the market and is user-oriented. TerraSAR is key to capturing a significant proportion of the existing market and to opening new market opportunities, when it becomes operational. The InfoTerra/TerraSAR Initiative has evolved gradually. It started in 1997 as a joint venture between German (DSS) and British (MMS-UK) space industry, strongly supported by both space agencies, DLR and BNSC. In early 2001, DLR and BNSC submitted to ESA the Formal Programme Proposal for InfoTerra/TerraSAR to become an essential element of ESA"s Earth Watch Programme. In summer 2001, when it became evident that there was not yet sufficient support from the ESA Member States to allow immediate start entering into TerraSAR Phase C/D, it has been decided to implement first a TerraSAR consolidation phase. In early 2002, in order to avoid further delays, a contract was signed between DLR and Astrium GmbH on the development of one component of TerraSAR, the TerraSAR-X, in the frame of a national programme, governed by a Public Private Partnership Agreement. Even if now the different launch dates for TerraSAR-X and TerraSAR-L are narrowing down the window of common data acquisition, it is a reasonable starting point, but it should always be kept in mind that the utmost goal for the longterm is to achieve self sustainability by supplying geo-information products and services

  5. Sentinel-3 SAR Altimetry Toolbox

    Science.gov (United States)

    Benveniste, Jerome; Lucas, Bruno; DInardo, Salvatore

    2015-04-01

    The prime objective of the SEOM (Scientific Exploitation of Operational Missions) element is to federate, support and expand the large international research community that the ERS, ENVISAT and the Envelope programmes have build up over the last 20 years for the future European operational Earth Observation missions, the Sentinels. Sentinel-3 builds directly on a proven heritage of ERS-2 and Envisat, and CryoSat-2, with a dual-frequency (Ku and C band) advanced Synthetic Aperture Radar Altimeter (SRAL) that provides measurements at a resolution of ~300m in SAR mode along track. Sentinel-3 will provide exact measurements of sea-surface height along with accurate topography measurements over sea ice, ice sheets, rivers and lakes. The first of the two Sentinels is expected to be launched in early 2015. The current universal altimetry toolbox is BRAT (Basic Radar Altimetry Toolbox) which can read all previous and current altimetry mission's data, but it does not have the capabilities to read the upcoming Sentinel-3 L1 and L2 products. ESA will endeavour to develop and supply this capability to support the users of the future Sentinel-3 SAR Altimetry Mission. BRAT is a collection of tools and tutorial documents designed to facilitate the processing of radar altimetry data. This project started in 2005 from the joint efforts of ESA (European Space Agency) and CNES (Centre National d'Etudes Spatiales), and it is freely available at http://earth.esa.int/brat. The tools enable users to interact with the most common altimetry data formats, the BratGUI is the front-end for the powerful command line tools that are part of the BRAT suite. BRAT can also be used in conjunction with Matlab/IDL (via reading routines) or in C/C++/Fortran via a programming API, allowing the user to obtain desired data, bypassing the data-formatting hassle. BRAT can be used simply to visualise data quickly, or to translate the data into other formats such as netCDF, ASCII text files, KML (Google Earth

  6. Feature extraction for SAR target recognition based on supervised manifold learning

    International Nuclear Information System (INIS)

    Du, C; Zhou, S; Sun, J; Zhao, J

    2014-01-01

    On the basis of manifold learning theory, a new feature extraction method for Synthetic aperture radar (SAR) target recognition is proposed. First, the proposed algorithm estimates the within-class and between-class local neighbourhood surrounding each SAR sample. After computing the local tangent space for each neighbourhood, the proposed algorithm seeks for the optimal projecting matrix by preserving the local within-class property and simultaneously maximizing the local between-class separability. The use of uncorrelated constraint can also enhance the discriminating power of the optimal projecting matrix. Finally, the nearest neighbour classifier is applied to recognize SAR targets in the projected feature subspace. Experimental results on MSTAR datasets demonstrate that the proposed method can provide a higher recognition rate than traditional feature extraction algorithms in SAR target recognition

  7. [Epidemiological perspectives on SARS and avian influenza].

    Science.gov (United States)

    del Rey Calero, Juan

    2004-01-01

    SARS is a respiratory infection caused by Coronavirus (Nidoviruses, RNA) from which 3 groups are known. Group 1 affects dogs, cats, pigs, and the human agent is 229 E. Group 2 affects bovines or rodents, and the human agent is OC43. And group 3 corresponds to the avian pathology.... The epidemics emerged on February 2003 in Guangdong, South China, due to consumption of exotic animals (Civeta, etc.), and it spread through interperson contagion to other regions in Asia, America and Europe. Incubation period is about 2-7 days. Transmission Of the virus is person-to person, but also by excretions and residual water. Basic reproductive rate is 2 to 4, and it is considered that 2.7 persons are infected from the initial case. In June 2003, SARS affected over 8,000 people and 774 were killed. Mortality approaches to 10%, and it is higher among older people rising up to 50% in those aged over 65 years. It is important to quickly establish action protocols regarding clinical, epidemiological and prevention aspects. Avian influenza is an infection caused by type A Influenza Orthomixovirus, in which migration birds and wild ducks are the main reservoir. Avian viruses correspond to H5, H7, H9. In 1997 it was observed that type AH5N1 jumped interspecies barrier and affected 18 humans, and 6 of them died. At the end of 2003 and in 2004 this type of poultry flu was described in Asia. FAO has emphasized that sacrifice of chicken in affected farms is the most effective measure to fight against the disease. It has also been established suppression of imports from these countries. There is no evidence on interperson contagion from chicken contagion, nor on food-borne contagion to humans.

  8. SARS – Koch´Postulates proved.

    Indian Academy of Sciences (India)

    SARS – Koch´Postulates proved. Novel coronavirus identified from fluids of patients. Virus cultured in Vero cell line. Sera of patients have antibodies to virus. Cultured virus produces disease in Macaque monkeys. -produces specific immune response; -isolated virus is SARS CoV; -pathology similar to human.

  9. SAR change detection techniques and applications

    NARCIS (Netherlands)

    Dekker, R.J.

    2005-01-01

    ABSTRACT: Change detection, the comparison of remote sensing images from different moments in time, is an important technique in environmental earth observation and security. SAR change detection is useful when weather and light conditions are unfavourable. Five methods of SAR change detection are

  10. PHARUS: A C-band Airborne SAR

    NARCIS (Netherlands)

    Hoogeboom, P.; Koomen, P.J.; Pouwels, H.; Snoeij, P.

    1990-01-01

    In The Netherlands a plan to design aircraft and build a polarimetric C-band SAR system of a novel design, called PHARUS (PHased Array Universal SAR) is carried out by three institutes. These institutes are the Physics and Electronics Laboratory TNO in The Hague (prime contractor and project

  11. Real-time brute force SAR processing

    NARCIS (Netherlands)

    Vlothuizen, W.J.; Ditzel, M.

    2009-01-01

    This paper presents a brute force method to perform real-time SAR processing. The method has several advantages over traditional so-called fast SAR implementations, as it does not make any approximations to alleviate the processing burden. However, the method does allow efficient implementation on

  12. SAR/MTI on small airborne platforms

    NARCIS (Netherlands)

    Rossum, W.L. van; Vermeulen, B.C.B.

    2006-01-01

    A small SAR-MTI system is being developed at TNO, aimed at deployment on tactical UAV. The system makes use of modern front-end technology, to provide flexible SAR imaging and MTI modes. Major design goals are 50 kg weight, 500 W power consumption and 50 cm resolution in order to comply with typical

  13. The Effect of Ankle, Knee and Hip Isokinetic Fatigue on Shock Absorption and Rate of Loading during Pair-leg Landing

    Directory of Open Access Journals (Sweden)

    Hamideh Khodaveisi

    2016-12-01

    Conclusion: Findings of this study indicate that the fatigue protocol using Isokinetic devices with uniform speed, increases muscle strength due to generating stress at all the joints, thereby, compensating the active and passive joints for shock absorption, and load distribution on the lower extremities. 

  14. Dynamic mechanical analysis and high strain-rate energy absorption characteristics of vertically aligned carbon nanotube reinforced woven fiber-glass composites

    Science.gov (United States)

    The dynamic mechanical behavior and energy absorption characteristics of nano-enhanced functionally graded composites, consisting of 3 layers of vertically aligned carbon nanotube (VACNT) forests grown on woven fiber-glass (FG) layer and embedded within 10 layers of woven FG, with polyester (PE) and...

  15. SAR processing using SHARC signal processing systems

    Science.gov (United States)

    Huxtable, Barton D.; Jackson, Christopher R.; Skaron, Steve A.

    1998-09-01

    Synthetic aperture radar (SAR) is uniquely suited to help solve the Search and Rescue problem since it can be utilized either day or night and through both dense fog or thick cloud cover. Other papers in this session, and in this session in 1997, describe the various SAR image processing algorithms that are being developed and evaluated within the Search and Rescue Program. All of these approaches to using SAR data require substantial amounts of digital signal processing: for the SAR image formation, and possibly for the subsequent image processing. In recognition of the demanding processing that will be required for an operational Search and Rescue Data Processing System (SARDPS), NASA/Goddard Space Flight Center and NASA/Stennis Space Center are conducting a technology demonstration utilizing SHARC multi-chip modules from Boeing to perform SAR image formation processing.

  16. Neutron resonance absorption theory

    International Nuclear Information System (INIS)

    Reuss, P.

    1991-11-01

    After some recalls on the physics of neutron resonance absorption during their slowing down, this paper presents the main features of the theoretical developments performed by the french school of reactor physics: the effective reaction rate method so called Livolant-Jeanpierre theory, the generalizations carried out by the author, and the probability table method [fr

  17. SARS: systematic review of treatment effects.

    Directory of Open Access Journals (Sweden)

    Lauren J Stockman

    2006-09-01

    Full Text Available BACKGROUND: The SARS outbreak of 2002-2003 presented clinicians with a new, life-threatening disease for which they had no experience in treating and no research on the effectiveness of treatment options. The World Health Organization (WHO expert panel on SARS treatment requested a systematic review and comprehensive summary of treatments used for SARS-infected patients in order to guide future treatment and identify priorities for research. METHODS AND FINDINGS: In response to the WHO request we conducted a systematic review of the published literature on ribavirin, corticosteroids, lopinavir and ritonavir (LPV/r, type I interferon (IFN, intravenous immunoglobulin (IVIG, and SARS convalescent plasma from both in vitro studies and in SARS patients. We also searched for clinical trial evidence of treatment for acute respiratory distress syndrome. Sources of data were the literature databases MEDLINE, EMBASE, BIOSIS, and the Cochrane Central Register of Controlled Trials (CENTRAL up to February 2005. Data from publications were extracted and evidence within studies was classified using predefined criteria. In total, 54 SARS treatment studies, 15 in vitro studies, and three acute respiratory distress syndrome studies met our inclusion criteria. Within in vitro studies, ribavirin, lopinavir, and type I IFN showed inhibition of SARS-CoV in tissue culture. In SARS-infected patient reports on ribavirin, 26 studies were classified as inconclusive, and four showed possible harm. Seven studies of convalescent plasma or IVIG, three of IFN type I, and two of LPV/r were inconclusive. In 29 studies of steroid use, 25 were inconclusive and four were classified as causing possible harm. CONCLUSIONS: Despite an extensive literature reporting on SARS treatments, it was not possible to determine whether treatments benefited patients during the SARS outbreak. Some may have been harmful. Clinical trials should be designed to validate a standard protocol for dosage

  18. Constraining ice mass loss from Jakobshavn Isbræ (Greenland) using InSAR-measured crustal uplift

    DEFF Research Database (Denmark)

    Liu, Lin; Wahr, John; Howat, Ian

    2012-01-01

    Jakobshavn Isbræ in west Greenland has been undergoing dramatic thinning since 1997. Applying the interferometric synthetic aperture radar (InSAR) technique to Radarsat-1 SAR data, we measure crustal uplift near Jakobshavn Isbræ caused by recent ice mass loss. The crustal uplift is predominantly......SAR-estimated deformation rates during 2004–2008 and the corresponding short-scale components of a deformation model that is based on changes in ice elevation measured by NASA’s Airborne Topographic Mapper (ATM). We are also able to use the InSAR-measured deformation to invert for the spatial pattern of ice thinning....... Overall, our results suggest that despite the inherent difficulties of working with a signal that has significant large-scale components, InSAR-measured crustal deformation can be used to study the ice mass loss of a rapidly thinning glacier and its surrounding catchment, providing both a constraint...

  19. Understanding bat SARS-like coronaviruses for the preparation of future coronavirus outbreaks - Implications for coronavirus vaccine development.

    Science.gov (United States)

    Ng, Oi-Wing; Tan, Yee-Joo

    2017-01-02

    The severe acute respiratory syndrome coronavirus (SARS-CoV) first emerged in 2003, causing the SARS epidemic which resulted in a 10% fatality rate. The advancements in metagenomic techniques have allowed the identification of SARS-like coronaviruses (SL-CoVs) sequences that share high homology to the human SARS-CoV epidemic strains from wildlife bats, presenting concrete evidence that bats are the origin and natural reservoir of SARS-CoV. The application of reverse genetics further enabled that characterization of these bat CoVs and the prediction of their potential to cause disease in humans. The knowledge gained from such studies is valuable in the surveillance and preparation of a possible future outbreak caused by a spill-over of these bat SL-CoVs.

  20. Rapid subsidence over oil fields measured by SAR

    Science.gov (United States)

    Fielding, E. J.; Blom, R. G.; Goldstein, R. M.

    1998-01-01

    The Lost Hills and Belridge oil felds are in the San Joaquin Valley, California. The major oil reservoir is high porosity and low permeability diatomite. Extraction of large volumes from shallow depths causes reduction in pore pressure and subsequent compaction, forming a surface subsidence bowl. We measure this subsidence from space using interferometric analysis of SAR (Synthetic Aperture Radar) data collected by the European Space Agency Remote Sensing Satellites (ERS-1 and ERS-2). Maximum subsidence rates are as high as 40 mm in 35 days or > 400 mm/yr, measured from interferograms with time separations ranging from one day to 26 months. The 8- and 26-month interferograms contain areas where the subsidence gradient exceeds the measurement possible with ERS SAR, but shows increased detail in areas of less rapid subsidence. Synoptic mapping of subsidence distribution from satellite data powerfully complements ground-based techniques, permits measurements where access is difficult, and aids identification of underlying causes.

  1. The synchronization method for distributed small satellite SAR

    Science.gov (United States)

    Xing, Lei; Gong, Xiaochun; Qiu, Wenxun; Sun, Zhaowei

    2007-11-01

    One of critical requirement for distributed small satellite SAR is the trigger time precision when all satellites turning on radar loads. This trigger operation is controlled by a dedicated communication tool or GPS system. In this paper a hardware platform is proposed which has integrated navigation, attitude control, and data handling system together. Based on it, a probabilistic synchronization method is proposed for SAR time precision requirement with ring architecture. To simplify design of transceiver, half-duplex communication way is used in this method. Research shows that time precision is relevant to relative frequency drift rate, satellite number, retry times, read error and round delay length. Installed with crystal oscillator short-term stability 10 -11 magnitude, this platform can achieve and maintain nanosecond order time error with a typical three satellites formation experiment during whole operating process.

  2. The influence of the reflective environment on the absorption of a human male exposed to representative base station antennas from 300 MHz to 5 GHz

    Energy Technology Data Exchange (ETDEWEB)

    Vermeeren, G; Joseph, W; Martens, L [Ghent University-INTEC/IBBT, Gaston Crommenlaan 8 box 201, B-9050 Ghent (Belgium); Gosselin, M C; Kuehn, S; Kuster, N [IT' IS Foundation, Zurich (Switzerland); Kellerman, V; Meyer, F [EMSS, Stellenbosch (South Africa); Hadjem, A; Gati, A; Wiart, J, E-mail: Gunter.Vermeeren@intec.UGent.b [Orange Labs, Paris (France)

    2010-09-21

    The environment is an important parameter when evaluating the exposure to radio-frequency electromagnetic fields. This study investigates numerically the variation on the whole-body and peak spatially averaged-specific absorption rate (SAR) in the heterogeneous virtual family male placed in front of a base station antenna in a reflective environment. The SAR values in a reflective environment are also compared to the values obtained when no environment is present (free space). The virtual family male has been placed at four distances (30 cm, 1 m, 3 m and 10 m) in front of six base station antennas (operating at 300 MHz, 450 MHz, 900 MHz, 2.1 GHz, 3.5 GHz and 5.0 GHz, respectively) and in three reflective environments (a perfectly conducting wall, a perfectly conducting ground and a perfectly conducting ground + wall). A total of 72 configurations are examined. The absorption in the heterogeneous body model is determined using the 3D electromagnetic (EM) finite-difference time-domain (FDTD) solver Semcad-X. For the larger simulations, requirements in terms of computer resources are reduced by using a generalized Huygens' box approach. It has been observed that the ratio of the SAR in the virtual family male in a reflective environment and the SAR in the virtual family male in the free-space environment ranged from -8.7 dB up to 8.0 dB. A worst-case reflective environment could not be determined. ICNIRP reference levels not always showed to be compliant with the basic restrictions.

  3. Processing PHARUS Data with the Generic SAR Processor

    NARCIS (Netherlands)

    Otten, M.P.G.

    1996-01-01

    The Generic SAR Processor (GSP) is a SAR processing environment created to process airborne and spaceborne SAR data with a maximum amount of flexibility, while at the same time providing a user friendly and powerful environment for handling and analyzing SAR, including polarimetric calibiation.

  4. Ship Detection in SAR Image Based on the Alpha-stable Distribution.

    Science.gov (United States)

    Wang, Changcheng; Liao, Mingsheng; Li, Xiaofeng

    2008-08-22

    This paper describes an improved Constant False Alarm Rate (CFAR) ship detection algorithm in spaceborne synthetic aperture radar (SAR) image based on Alphastable distribution model. Typically, the CFAR algorithm uses the Gaussian distribution model to describe statistical characteristics of a SAR image background clutter. However, the Gaussian distribution is only valid for multilook SAR images when several radar looks are averaged. As sea clutter in SAR images shows spiky or heavy-tailed characteristics, the Gaussian distribution often fails to describe background sea clutter. In this study, we replace the Gaussian distribution with the Alpha-stable distribution, which is widely used in impulsive or spiky signal processing, to describe the background sea clutter in SAR images. In our proposed algorithm, an initial step for detecting possible ship targets is employed. Then, similar to the typical two-parameter CFAR algorithm, a local process is applied to the pixel identified as possible target. A RADARSAT-1 image is used to validate this Alpha-stable distribution based algorithm. Meanwhile, known ship location data during the time of RADARSAT-1 SAR image acquisition is used to validate ship detection results. Validation results show improvements of the new CFAR algorithm based on the Alpha-stable distribution over the CFAR algorithm based on the Gaussian distribution.

  5. Ship Detection in SAR Image Based on the Alpha-stable Distribution

    Directory of Open Access Journals (Sweden)

    Xiaofeng Li

    2008-08-01

    Full Text Available This paper describes an improved Constant False Alarm Rate (CFAR ship detection algorithm in spaceborne synthetic aperture radar (SAR image based on Alphastable distribution model. Typically, the CFAR algorithm uses the Gaussian distribution model to describe statistical characteristics of a SAR image background clutter. However, the Gaussian distribution is only valid for multilook SAR images when several radar looks are averaged. As sea clutter in SAR images shows spiky or heavy-tailed characteristics, the Gaussian distribution often fails to describe background sea clutter. In this study, we replace the Gaussian distribution with the Alpha-stable distribution, which is widely used in impulsive or spiky signal processing, to describe the background sea clutter in SAR images. In our proposed algorithm, an initial step for detecting possible ship targets is employed. Then, similar to the typical two-parameter CFAR algorithm, a local process is applied to the pixel identified as possible target. A RADARSAT-1 image is used to validate this Alpha-stable distribution based algorithm. Meanwhile, known ship location data during the time of RADARSAT-1 SAR image acquisition is used to validate ship detection results. Validation results show improvements of the new CFAR algorithm based on the Alpha-stable distribution over the CFAR algorithm based on the Gaussian distribution.

  6. LAND SUBSIDENCE MONITORING USING PS-InSAR TECHNIQUE FOR L-BAND SAR DATA

    Directory of Open Access Journals (Sweden)

    S. Thapa

    2016-10-01

    Full Text Available Differential SAR-Interferometry (D-InSAR is one of the potential source to measure land surface motion induced due to underground coal mining. However, this technique has many limitation such as atmospheric in homogeneities, spatial de-correlation, and temporal decorrelation. Persistent Scatterer Interferometry synthetic aperture radar (PS-InSAR belongs to a family of time series InSAR technique, which utilizes the properties of some of the stable natural and anthropogenic targets which remain coherent over long time period. In this study PS-InSAR technique has been used to monitor land subsidence over selected location of Jharia Coal field which has been correlated with the ground levelling measurement. This time series deformation observed using PS InSAR helped us to understand the nature of the ground surface deformation due to underground mining activity.

  7. Offshore wind mapping Mediterranean area using SAR

    DEFF Research Database (Denmark)

    Calaudi, Rosamaria; Arena, Felice; Badger, Merete

    2013-01-01

    Satellite observations of the ocean surface, for example from Synthetic Aperture Radars (SAR), provide information about the spatial wind variability over large areas. This is of special interest in the Mediterranean Sea, where spatial wind information is only provided by sparse buoys, often...... with long periods of missing data. Here, we focus on evaluating the use of SAR for offshore wind mapping. Preliminary results from the analysis of SAR-based ocean winds in Mediterranean areas show interesting large scale wind flow features consistent with results from previous studies using numerical models...

  8. Primary studies of Chinese spaceborne SAR

    Science.gov (United States)

    Wang, Zhen-Song; Wu, Guo-Xiang; Guo, Hua-Dong; Wei, Zhong-Quan; Zhu, Min-Hui

    1993-01-01

    The primary studies on spaceborne synthetic aperture radar (SAR) in China are discussed. The SAR will be launched aboard a Chinese satellite and operated at L-band with HH polarization. The purpose of the mission in consideration is dedicated to resources and environment uses, especially to natural disaster monitoring. The ground resolution is designed as 25 m x 25 m for detailed mode and 100 m x 100 m for wide scan-SAR mode. The off-nadir angle can be varied from 20 to 40 deg. The key system concepts are introduced.

  9. AUTOMATIC INTERPRETATION OF HIGH RESOLUTION SAR IMAGES: FIRST RESULTS OF SAR IMAGE SIMULATION FOR SINGLE BUILDINGS

    Directory of Open Access Journals (Sweden)

    J. Tao

    2012-09-01

    Full Text Available Due to the all-weather data acquisition capabilities, high resolution space borne Synthetic Aperture Radar (SAR plays an important role in remote sensing applications like change detection. However, because of the complex geometric mapping of buildings in urban areas, SAR images are often hard to interpret. SAR simulation techniques ease the visual interpretation of SAR images, while fully automatic interpretation is still a challenge. This paper presents a method for supporting the interpretation of high resolution SAR images with simulated radar images using a LiDAR digital surface model (DSM. Line features are extracted from the simulated and real SAR images and used for matching. A single building model is generated from the DSM and used for building recognition in the SAR image. An application for the concept is presented for the city centre of Munich where the comparison of the simulation to the TerraSAR-X data shows a good similarity. Based on the result of simulation and matching, special features (e.g. like double bounce lines, shadow areas etc. can be automatically indicated in SAR image.

  10. Improving the applicability of (Q)SARs for percutaneous penetration in regulatory risk assessment.

    Science.gov (United States)

    Bouwman, T; Cronin, M T D; Bessems, J G M; van de Sandt, J J M

    2008-04-01

    The new regulatory framework REACH (Registration, Evaluation, and Authorisation of Chemicals) foresees the use of non-testing approaches, such as read-across, chemical categories, structure-activity relationships (SARs) and quantitative structure-activity relationships (QSARs). Although information on skin absorption data are not a formal requirement under REACH, data on dermal absorption are an integral part of risk assessment of substances/products to which man is predominantly exposed via the dermal route. In this study, we assess the present applicability of publicly available QSARs on skin absorption for risk assessment purposes. We explicitly did not aim to give scientific judgments on individual QSARs. A total of 33 QSARs selected from the public domain were evaluated using the OECD (Organisation for Economic Co-operation and Development) Principles for the Validation of (Q)SAR Models. Additionally, several pragmatic criteria were formulated to select QSARs that are most suitable for their use in regulatory risk assessment. Based on these criteria, four QSARs were selected. The predictivity of these QSARs was evaluated by comparing their outcomes with experimentally derived skin absorption data (for 62 compounds). The predictivity was low for three of four QSARs, whereas one model gave reasonable predictions. Several suggestions are made to increase the applicability of QSARs for skin absorption for risk assessment purposes.

  11. Work session on the SAR. Pt. 2

    International Nuclear Information System (INIS)

    Burkart, K.

    1980-01-01

    The present paper contains the tables of the contribution of K. Burkart 'Work Session on the SAR' to the IAEA Interregional Training Course held in Sept/Oct. 1980 at the Kernforschungszentrum Karlsruhe. (RW)

  12. Image based SAR product simulation for analysis

    Science.gov (United States)

    Domik, G.; Leberl, F.

    1987-01-01

    SAR product simulation serves to predict SAR image gray values for various flight paths. Input typically consists of a digital elevation model and backscatter curves. A new method is described of product simulation that employs also a real SAR input image for image simulation. This can be denoted as 'image-based simulation'. Different methods to perform this SAR prediction are presented and advantages and disadvantages discussed. Ascending and descending orbit images from NASA's SIR-B experiment were used for verification of the concept: input images from ascending orbits were converted into images from a descending orbit; the results are compared to the available real imagery to verify that the prediction technique produces meaningful image data.

  13. SARS Patients and Their Close Contacts

    Science.gov (United States)

    ... Guidance for Airline Personnel Guidance on Air Medical Transport for SARS Patients Legal Authorities for Isolation and ... g., bus, taxi). Do not go to work, school, out-of-home child care, church, or activities ...

  14. Satellite sar detection of hurricane helene (2006)

    DEFF Research Database (Denmark)

    Ju, Lian; Cheng, Yongcun; Xu, Qing

    2013-01-01

    In this paper, the wind structure of hurricane Helene (2006) over the Atlantic Ocean is investigated from a C-band RADARSAT-1 synthetic aperture radar (SAR) image acquired on 20 September 2006. First, the characteristics, e.g., the center, scale and area of the hurricane eye (HE) are determined....... There is a good agreement between the SAR-estimated HE center location and the best track data from the National Hurricane Center. The wind speeds at 10 m above the ocean surface are also retrieved from the SAR data using the geophysical model function (GMF), CMOD5, and compared with in situ wind speed...... observations from the stepped frequency microwave radiometer (SFMR) on NOAA P3 aircraft. All the results show the capability of hurricane monitoring by satellite SAR. Copyright © 2013 by the International Society of Offshore and Polar Engineers (ISOPE)....

  15. Small Sar Satellite Using Small Standard Bus

    OpenAIRE

    Ono, Kiyonobu; Fujimura, Takashi; Ogawa, Toshiaki; Kimura, Tsunekazu

    2011-01-01

    This paper introduces a new small SAR (Synthetic Aperture Radar) satellite that follows the small optical sensor satellite, ASNARO. USEF, NEDO and NEC are developing ASNARO satellite, which is a small LEO satellite (total mass

  16. MiTAP for SARS Detection

    National Research Council Canada - National Science Library

    Damianos, Laurie E; Bayer, Samuel; Chisholm, Michael A; Henderson, John; Hirschman, Lynette; Morgan, William; Ubaldino, Marc; Zarrella, Guido; Wilson, V, James M; Polyak, Marat G

    2006-01-01

    The MiTAP prototype for SARS detection uses human language technology for detecting, monitoring, and analyzing potential indicators of infectious disease outbreaks and reasoning for issuing warnings and alerts...

  17. Attribute Learning for SAR Image Classification

    Directory of Open Access Journals (Sweden)

    Chu He

    2017-04-01

    Full Text Available This paper presents a classification approach based on attribute learning for high spatial resolution Synthetic Aperture Radar (SAR images. To explore the representative and discriminative attributes of SAR images, first, an iterative unsupervised algorithm is designed to cluster in the low-level feature space, where the maximum edge response and the ratio of mean-to-variance are included; a cross-validation step is applied to prevent overfitting. Second, the most discriminative clustering centers are sorted out to construct an attribute dictionary. By resorting to the attribute dictionary, a representation vector describing certain categories in the SAR image can be generated, which in turn is used to perform the classifying task. The experiments conducted on TerraSAR-X images indicate that those learned attributes have strong visual semantics, which are characterized by bright and dark spots, stripes, or their combinations. The classification method based on these learned attributes achieves better results.

  18. Multiple Input - Multiple Output (MIMO) SAR

    Data.gov (United States)

    National Aeronautics and Space Administration — This effort will research and implement advanced Multiple-Input Multiple-Output (MIMO) Synthetic Aperture Radar (SAR) techniques which have the potential to improve...

  19. Simultaneous Navigation and SAR Auto-Focusing

    OpenAIRE

    Sjanic, Zoran; Gustafsson, Fredrik

    2010-01-01

    Synthetic Aperture Radar (SAR) equipment is an all-weather radar imaging system that can create high resolution images by means of utilising the movement of the flying platform. Accurate knowledge of the flown trajectory is essential in order to get focused images. Recently SAR systems are becoming more used on smaller and cheaper flying platforms like Unmanned Aerial Vehicles (UAV). Since UAVs in general have navigation systems with poorer performance than manned aircraft, the resulting images ...

  20. Wave directional spectrum from SAR imagery

    Digital Repository Service at National Institute of Oceanography (India)

    Fernandes, A.A.; Sarma, Y.V.B.; Menon, H.B.; Vethamony, P.

    with radar imagery. 1. SAR Measurements Digital ERS-1 image mode SAR scenes off Goa, Paradeep and Visakhapatnam were acquired from the National Remote Sensing Agency (NRSA), Hyderabad, India, with the intention of studying the spatial evolution... density and wave direction separately as a function of frequency using the digital band, pass filtering method, the buoy observation at 1050 IST showed (Table 1) that there were two main spectral peaks, both due to "swell" ( waves generated by distant...

  1. SARS: Key factors in crisis management.

    Science.gov (United States)

    Tseng, Hsin-Chao; Chen, Thai-Form; Chou, Shieu-Ming

    2005-03-01

    This study was conducted at a single hospital selected in Taipei during the SARS (Severe Acute Respiratory Syndrome) outbreak from March to July, 2003 in Taiwan. During this period of time, 104 SARS patients were admitted to the hospital. There were no negative reports related to the selected hospital despite its being located right in the center of an area struck by the epidemic. The purpose of this study was to identify the key factors enabling the hospital to survive SARS unscathed. Data were collected from in-depth interviews with the nursing directors and nursing managers of the SARS units, along with a review of relevant hospital documents. The five key elements identified as survival factors during this SARS crisis are as follows: 1. good control of timing for crisis management, 2. careful decision-making, 3. thorough implementation, 4. effective communication, and 5. trust between management and employees. The results of this study reconfirmed the selected hospital as a model for good crisis management during the SARS epidemic.

  2. Potential of TCPInSAR in Monitoring Linear Infrastructure with a Small Dataset of SAR Images: Application of the Donghai Bridge, China

    Directory of Open Access Journals (Sweden)

    Lei Zhang

    2018-03-01

    Full Text Available Reliably monitoring deformation associated with linear infrastructures, such as long-span bridges, is vitally important to assess their structural health. In this paper, we attempt to employ satellite interferometric synthetic aperture radar (InSAR to map the deformation of Donghai Bridge over a half of an annual cycle. The bridge, as the fourth longest cross-sea bridge in the world, located in the north of Hangzhou Bay, East China Sea where the featureless sea surface largely occupied the radar image raises challenges to accurately co-register the coherent points along the bridge. To tackle the issues due to co-registration and the limited number of synthetic aperture radar (SAR images, we adopt the termed temporarily-coherent point (TCP InSAR (TCPInSAR technique to process the radar images. TCPs that are not necessarily coherent during the whole observation period can be identified within every two SAR acquisitions during the co-registration procedure based on the statistics of azimuth and range offsets. In the process, co-registration is performed only using the offsets of these TCPs, leading to improved interferometric phases and the local Delaunay triangulation is used to construct point pairs to reduce the atmospheric artifacts along the bridge. With the TCPInSAR method the deformation rate along the bridge is estimated with no need of phase unwrapping. The achieved result reveals that the Donghai Bridge suffered a line-of-sight (LOS deformation rate up to −2.3 cm/year from January 2009 to July 2009 at the cable-stayed part, which is likely due to the thermal expansion of cables.

  3. Electromagnetic Energy Absorption due to Wireless Energy Transfer: A Brief Review

    Directory of Open Access Journals (Sweden)

    Syafiq A.

    2016-01-01

    Full Text Available This paper reviews an implementation of evaluating compliance of wireless power transfer systems with respect to human electromagnetic exposure limits. Methods for both numerical analysis and measurements are discussed. The objective is to evaluate the rate of which energy is absorbed by the human body when exposed to a wireless energy transfer, although it can be referred to the absorption of other forms of energy by tissue. An exposure assessment of a representative wireless power transfer system, under a limited set of operating conditions, is provided in order to estimate the maximum SAR levels. The aim of this review is to conclude the possible side effect to the human body when utilizing wireless charging in daily life so that an early severe action can be taken when using wireless transfer.

  4. Generation of human antibody fragments recognizing distinct epitopes of the nucleocapsid (N SARS-CoV protein using a phage display approach

    Directory of Open Access Journals (Sweden)

    Grasso Felicia

    2005-09-01

    Full Text Available Abstract Background Severe acute respiratory syndrome (SARS-CoV is a newly emerging virus that causes SARS with high mortality rate in infected people. Successful control of the global SARS epidemic will require rapid and sensitive diagnostic tests to monitor its spread, as well as, the development of vaccines and new antiviral compounds including neutralizing antibodies that effectively prevent or treat this disease. Methods The human synthetic single-chain fragment variable (scFv ETH-2 phage antibody library was used for the isolation of scFvs against the nucleocapsid (N protein of SARS-CoV using a bio panning-based strategy. The selected scFvs were characterized under genetics-molecular aspects and for SARS-CoV N protein detection in ELISA, western blotting and immunocytochemistry. Results Human scFv antibodies to N protein of SARS-CoV can be easily isolated by selecting the ETH-2 phage library on immunotubes coated with antigen. These in vitro selected human scFvs specifically recognize in ELISA and western blotting studies distinct epitopes in N protein domains and detect in immunohistochemistry investigations SARS-CoV particles in infected Vero cells. Conclusion The human scFv antibodies isolated and described in this study represent useful reagents for rapid detection of N SARS-CoV protein and SARS virus particles in infected target cells.

  5. Generation of human antibody fragments recognizing distinct epitopes of the nucleocapsid (N) SARS-CoV protein using a phage display approach

    Science.gov (United States)

    Flego, Michela; Di Bonito, Paola; Ascione, Alessandro; Zamboni, Silvia; Carattoli, Alessandra; Grasso, Felicia; Cassone, Antonio; Cianfriglia, Maurizio

    2005-01-01

    Background Severe acute respiratory syndrome (SARS)-CoV is a newly emerging virus that causes SARS with high mortality rate in infected people. Successful control of the global SARS epidemic will require rapid and sensitive diagnostic tests to monitor its spread, as well as, the development of vaccines and new antiviral compounds including neutralizing antibodies that effectively prevent or treat this disease. Methods The human synthetic single-chain fragment variable (scFv) ETH-2 phage antibody library was used for the isolation of scFvs against the nucleocapsid (N) protein of SARS-CoV using a bio panning-based strategy. The selected scFvs were characterized under genetics-molecular aspects and for SARS-CoV N protein detection in ELISA, western blotting and immunocytochemistry. Results Human scFv antibodies to N protein of SARS-CoV can be easily isolated by selecting the ETH-2 phage library on immunotubes coated with antigen. These in vitro selected human scFvs specifically recognize in ELISA and western blotting studies distinct epitopes in N protein domains and detect in immunohistochemistry investigations SARS-CoV particles in infected Vero cells. Conclusion The human scFv antibodies isolated and described in this study represent useful reagents for rapid detection of N SARS-CoV protein and SARS virus particles in infected target cells. PMID:16171519

  6. Target detection in SAR images via radiometric multi-resolution analysis

    Science.gov (United States)

    Hu, Jingwen; Xia, Gui-Song; Sun, Hong

    2013-10-01

    This paper presents a target detection method in synthetic aperture radar (SAR) images with radiometric multiresolution analysis (RMA). The idea is that target saliency can be efficiently computed by comparing the statistics of targets and those of the local background around them. In order to compute reliable statistics of targets, which usually involve a small number of pixels, RMA is adopted. The RMA preprocessing method performs well in stabilizing the statistical characteristics of SAR images. It can effectively restrain the speckle noise while keep the statistical characteristics of the original image. Based on the computed target saliency, adaptive decision thresholds are got by using the constant false alarm rate (CFAR) target detection framework. Our experiments on real SAR images show that the proposed method can achieve better performance compared with the traditional cell average-constant false alarm rate (CA-CFAR) method.

  7. Accelerating Spaceborne SAR Imaging Using Multiple CPU/GPU Deep Collaborative Computing.

    Science.gov (United States)

    Zhang, Fan; Li, Guojun; Li, Wei; Hu, Wei; Hu, Yuxin

    2016-04-07

    With the development of synthetic aperture radar (SAR) technologies in recent years, the huge amount of remote sensing data brings challenges for real-time imaging processing. Therefore, high performance computing (HPC) methods have been presented to accelerate SAR imaging, especially the GPU based methods. In the classical GPU based imaging algorithm, GPU is employed to accelerate image processing by massive parallel computing, and CPU is only used to perform the auxiliary work such as data input/output (IO). However, the computing capability of CPU is ignored and underestimated. In this work, a new deep collaborative SAR imaging method based on multiple CPU/GPU is proposed to achieve real-time SAR imaging. Through the proposed tasks partitioning and scheduling strategy, the whole image can be generated with deep collaborative multiple CPU/GPU computing. In the part of CPU parallel imaging, the advanced vector extension (AVX) method is firstly introduced into the multi-core CPU parallel method for higher efficiency. As for the GPU parallel imaging, not only the bottlenecks of memory limitation and frequent data transferring are broken, but also kinds of optimized strategies are applied, such as streaming, parallel pipeline and so on. Experimental results demonstrate that the deep CPU/GPU collaborative imaging method enhances the efficiency of SAR imaging on single-core CPU by 270 times and realizes the real-time imaging in that the imaging rate outperforms the raw data generation rate.

  8. InSAR and GPS time series analysis: Crustal deformation in the Yucca Mountain, Nevada region

    Science.gov (United States)

    Li, Z.; Hammond, W. C.; Blewitt, G.; Kreemer, C. W.; Plag, H.

    2010-12-01

    Several previous studies have successfully demonstrated that long time series (e.g. >5 years) of GPS measurements can be employed to detect tectonic signals with a vertical rate greater than 0.3 mm/yr (e.g. Hill and Blewitt, 2006; Bennett et al. 2009). However, GPS stations are often sparse, with spacing from a few kilometres to a few hundred kilometres. Interferometric SAR (InSAR) can complement GPS by providing high horizontal spatial resolution (e.g. meters to tens-of metres) over large regions (e.g. 100 km × 100 km). A major source of error for repeat-pass InSAR is the phase delay in radio signal propagation through the atmosphere. The portion of this attributable to tropospheric water vapour causes errors as large as 10-20 cm in deformation retrievals. InSAR Time Series analysis with Atmospheric Estimation Models (InSAR TS + AEM), developed at the University of Glasgow, is a robust time series analysis approach, which mainly uses interferograms with small geometric baselines to minimise the effects of decorrelation and inaccuracies in topographic data. In addition, InSAR TS + AEM can be used to separate deformation signals from atmospheric water vapour effects in order to map surface deformation as it evolves in time. The principal purposes of this study are to assess: (1) how consistent InSAR-derived deformation time series are with GPS; and (2) how precise InSAR-derived atmospheric path delays can be. The Yucca Mountain, Nevada region is chosen as the study site because of its excellent GPS network and extensive radar archives (>10 years of dense and high-quality GPS stations, and >17 years of ERS and ENVISAT radar acquisitions), and because of its arid environment. The latter results in coherence that is generally high, even for long periods that span the existing C-band radar archives of ERS and ENVISAT. Preliminary results show that our InSAR LOS deformation map agrees with GPS measurements to within 0.35 mm/yr RMS misfit at the stations which is the

  9. Geolocation with error analysis using imagery from an experimental spotlight SAR

    Science.gov (United States)

    Wonnacott, William Mark

    This dissertation covers the development of a geometry-based sensor model for a specific monostatic spotlight synthetic aperture radar (SAR) system---referred to as the ExSAR (for experimental SAR). This sensor model facilitates single- and multiple-image geopositioning with error analysis. It allows for the use of known ground control points in refining the collection geometry parameters (a process called image resection) and for the subsequent geopositioning of other points using the resected image. Theoretically, the model also allows for the potential recovery of bias-like, persistent errors common across multiple images. The model also includes multi-image correspondence equations to aid in the cross-image identification of conjugate points. The sensor model development begins with a generic, theoretical approach to the modeling of spotlight SAR. A closed-form solution to the range and range-rate condition equations and the corresponding error propagation equation are presented. (The SAR condition equations have traditionally been solved iteratively.) The application of the closed-form solution in the image-to-ground and ground-to-image transformations is documented. The theoretical work also includes a preliminary error sensitivity analysis and a treatment of the spotlight SAR resection process. The ExSAR-specific model is established and assessed with an extensive set of images collected using the experimental radar over arrays of ground control points. Using this set, the imagery metadata elements are assessed, and the optimal element set for geopositioning is determined. The ExSAR imagery is shown to be transformed to the ground plane in only one dimension. The eventual ExSAR sensor model is used with known elevations and single-image geopositioning to show a horizontal accuracy of 8.23 m (rms). With resection using five ground-surveyed control points per image, the horizontal accuracy of reserved check points is 0.45 m (rms). Resections using the same

  10. Influence of GSM900 electromagnetic fields on the metabolic rate in rodents

    Directory of Open Access Journals (Sweden)

    A. El Ouardi

    2008-05-01

    Full Text Available The development of exposure devices for investigating possible effects of mobile communication systems to non-restrained animals aims at a homogenous field distribution in the area the animals occupy. In the presented 900 MHz exposure device a quite good field homogeneity of 5% (including the standing wave contribution due to internal reflections is reached in the cage region mainly by flattening the transverse field. For the standard waveguide (WR1150 without dielectric sheets this value reads 14%. The desired maximal whole body specific absorption rate (SAR of 4 W/kg in the Djungarian hamster model is achieved at an input power of only 3.7 W.

  11. Influence of GSM900 electromagnetic fields on the metabolic rate in rodents

    Science.gov (United States)

    El Ouardi, A.; Streckert, J.; Lerchl, A.; Schwarzpaul, K.; Hansen, V.

    2008-05-01

    The development of exposure devices for investigating possible effects of mobile communication systems to non-restrained animals aims at a homogenous field distribution in the area the animals occupy. In the presented 900 MHz exposure device a quite good field homogeneity of 5% (including the standing wave contribution due to internal reflections) is reached in the cage region mainly by flattening the transverse field. For the standard waveguide (WR1150) without dielectric sheets this value reads 14%. The desired maximal whole body specific absorption rate (SAR) of 4 W/kg in the Djungarian hamster model is achieved at an input power of only 3.7 W.

  12. Synthetic SAR Image Generation using Sensor, Terrain and Target Models

    DEFF Research Database (Denmark)

    Kusk, Anders; Abulaitijiang, Adili; Dall, Jørgen

    2016-01-01

    A tool to generate synthetic SAR images of objects set on a clutter background is described. The purpose is to generate images for training Automatic Target Recognition and Identification algorithms. The tool employs a commercial electromagnetic simulation program to calculate radar cross sections...... of the object using a CAD-model. The raw measurements are input to a SAR system and terrain model, which models thermal noise, terrain clutter, and SAR focusing to produce synthetic SAR images. Examples of SAR images at 0.3m and 0.1m resolution, and a comparison with real SAR imagery from the MSTAR dataset...

  13. Mars Mission Concepts: SAR and Solar Electric Propulsion

    Science.gov (United States)

    Elsperman, M.; Klaus, K.; Smith, D. B.; Clifford, S. M.; Lawrence, S. J.

    2012-12-01

    Introduction: The time has come to leverage technology advances (including advances in autonomous operation and propulsion technology) to reduce the cost and increase the flight rate of planetary missions, while actively developing a scientific and engineering workforce to achieve national space objectives. Mission Science at Mars: A SAR imaging radar offers an ability to conduct high resolution investigations of the shallow (system would enable the generation of false color images, resulting in useful science results, and the stereo data could be reduced into high-resolution Digital Elevation Models uniquely useful for exploration planning and science purposes. Since the SAR and the notional high-resolution stereo imaging system would be huge data volume producers - to maximize the science return we are currently considering the usage of laser communications systems; this notional spacecraft represents one pathway to evaluate the utility of laser communications in planetary exploration while providing useful science return.. Mission Concept: Using a common space craft for multiple missions reduces costs. Solar electric propulsion (SEP) provides the flexibility required for multiple mission objectives. SEP provides the greatest payload advantage albeit at the sacrifice of mission time. Our concept involves using a SEP enabled space craft (Boeing 702SP) with a highly capable SAR imager that also conducts autonomous rendezvous and docking experiments accomplished from Mars orbit. Our concept of operations is to launch on May 5, 2018 using a launch vehicle with 2000kg launch capacity with a C3 of 7.4. After reaching Mars it takes 145 days to spiral down to a 250 km orbit above the surface of Mars when Mars SAR operations begin. Summary/Conclusions: A robust and compelling Mars mission can be designed to meet the 2018 Mars launch window opportunity. Using advanced in-space power and propulsion technologies like High Power Solar Electric Propulsion provides enormous

  14. Human monoclonal antibody as prophylaxis for SARS coronavirus infection in ferrets

    NARCIS (Netherlands)

    ter Meulen, Jan; Bakker, Alexander B. H.; van den Brink, Edward N.; Weverling, Gerrit J.; Martina, Byron E. E.; Haagmans, Bart L.; Kuiken, Thijs; de Kruif, John; Preiser, Wolfgang; Spaan, Willy; Gelderblom, Hans R.; Goudsmit, Jaap; Osterhaus, Albert D. M. E.

    2004-01-01

    SARS coronavirus continues to cause sporadic cases of severe acute respiratory syndrome (SARS) in China. No active or passive immunoprophylaxis for disease induced by SARS coronavirus is available. We investigated prophylaxis of SARS coronavirus infection with a neutralising human monoclonal

  15. Opposing Roles of the Staphylococcus aureus Virulence Regulators, Agr and Sar, in Triton X-100- and Penicillin-Induced Autolysis

    OpenAIRE

    Fujimoto, David F.; Bayles, Kenneth W.

    1998-01-01

    The regulation of murein hydrolases is a critical aspect of peptidoglycan growth and metabolism. In the present study, we demonstrate that mutations within the Staphylococcus aureus virulence factor regulatory genes, agr and sar, affect autolysis, resulting in decreased and increased autolysis rates, respectively. Zymographic analyses of these mutant strains suggest that agr and sar exert their effects on autolysis, in part, by modulating murein hydrolase expression and/or activity.

  16. Use of SAR data for proliferation monitoring

    International Nuclear Information System (INIS)

    Lafitte, M.; Robin, J.P.

    2013-01-01

    Synthetic Aperture Radar (SAR) is an active and coherent system. SAR images are complex data which contain both amplitude and phase information. The analysis of single SAR data required a very good experience and a good understanding of SAR geometry regarding layover, shadowing, texture and speckle. Image analyst can depicts and describes most of the facilities related to nuclear proliferation and weapons of mass destruction (WMD). The Amplitude Change Detection (ACD) technique consists of a combination of two or three SAR amplitude data acquired with similar orbit and frequency parameters on different dates. That technique provides a very good overview of the changes and particularly regarding vehicles activity and constructions ongoing within the area of interest over the monitoring period. One of the particularities of the SAR systems is to be coherent. The phase of a single image is not exploitable. Thus when two or more SAR data have been acquired with identical orbit and frequency parameters, the phases shift are indicators of changes such as structural changes, terrain subsidence or motion. The Multi-Temporal Coherence (MTC) product merged the two type of information previously detailed: the ACD and coherence analysis. It consists of the combination of two amplitude images and the corresponding coherence computed image. The MTC image may highlights changes between two states of a target which on the ACD analysis appeared unchanged. EUSC uses the difference interferometry techniques in order to estimate volumes that have changed between two acquisition dates. The paper is followed by the slides of the presentation. (A.C.)

  17. MONITORING OF LAND SUBSIDENCE IN RAVENNA MUNICIPALITY USING INTEGRATED SAR - GPS TECHNIQUES: DESCRIPTION AND FIRST RESULTS

    Directory of Open Access Journals (Sweden)

    G. Artese

    2016-06-01

    Full Text Available The Emilia Romagna Region (N-E Italy and in particular the Adriatic Sea coastline of Ravenna, is affected by a noticeable subsidence that started in the 1950s, when the exploitation of on and off-shore methane reservoirs began, along with the pumping of groundwater for industrial uses. In such area the current subsidence rate, even if lower than in the past, reaches the -2 cm/y. Over the years, local Authorities have monitored this phenomenon with different techniques: spirit levelling, GPS surveys and, more recently, Differential Interferometric Synthetic Aperture Radar (DInSAR techniques, confirming the critical situation of land subsidence risk. In this work, we present the comparison between the results obtained with DInSAR and GPS techniques applied to the study of the land subsidence in the Ravenna territory. With regard to the DInSAR, the Small Baseline Subset (SBAS and the Coherent Pixel Technique (CPT techniques have been used. Different SAR datasets have been exploited: ERS-1/2, ENVISAT, TerraSAR-X and Sentinel-1. Some GPS campaigns have been also carried out in a subsidence prone area. 3D vertices have been selected very close to existing persistent scatterers in order to link the GPS measurement results to the SAR ones. GPS data were processed into the International reference system and the comparisons between the coordinates, for the first 6 months of the monitoring, provided results with the same trend of the DInSAR data, even if inside the precision of the method.

  18. Optimization of synthesis and peptization steps to obtain iron oxide nanoparticles with high energy dissipation rates

    Energy Technology Data Exchange (ETDEWEB)

    Mérida, Fernando [Deparment of Chemical Engineering, University of Puerto Rico, Mayagüez, P.O. Box 9046, Mayagüez, PR 00680 (United States); Chiu-Lam, Andreina [Department of Chemical Engineering, University of Florida, P.O. Box 116005, Gainesville, FL 32611-6005 (United States); Bohórquez, Ana C. [J. Crayton Pruitt Family Department of Biomedical Engineering, University of Florida, P.O. Box 116131, Gainesville, FL 32611-6131 (United States); Maldonado-Camargo, Lorena [Department of Chemical Engineering, University of Florida, P.O. Box 116005, Gainesville, FL 32611-6005 (United States); Pérez, María-Eglée; Pericchi, Luis [Department of Mathematics, University of Puerto Rico, Río Piedras, P.O. Box 70377, San Juan, PR 00936-8377 (United States); Torres-Lugo, Madeline [Deparment of Chemical Engineering, University of Puerto Rico, Mayagüez, P.O. Box 9046, Mayagüez, PR 00680 (United States); Rinaldi, Carlos, E-mail: carlos.rinaldi@bme.ufl.edu [Department of Chemical Engineering, University of Florida, P.O. Box 116005, Gainesville, FL 32611-6005 (United States); J. Crayton Pruitt Family Department of Biomedical Engineering, University of Florida, P.O. Box 116131, Gainesville, FL 32611-6131 (United States)

    2015-11-15

    Magnetic Fluid Hyperthermia (MFH) uses heat generated by magnetic nanoparticles exposed to alternating magnetic fields to cause a temperature increase in tumors to the hyperthermia range (43–47 °C), inducing apoptotic cancer cell death. As with all cancer nanomedicines, one of the most significant challenges with MFH is achieving high nanoparticle accumulation at the tumor site. This motivates development of synthesis strategies that maximize the rate of energy dissipation of iron oxide magnetic nanoparticles, preferable due to their intrinsic biocompatibility. This has led to development of synthesis strategies that, although attractive from the point of view of chemical elegance, may not be suitable for scale-up to quantities necessary for clinical use. On the other hand, to date the aqueous co-precipitation synthesis, which readily yields gram quantities of nanoparticles, has only been reported to yield sufficiently high specific absorption rates after laborious size selective fractionation. This work focuses on improvements to the aqueous co-precipitation of iron oxide nanoparticles to increase the specific absorption rate (SAR), by optimizing synthesis conditions and the subsequent peptization step. Heating efficiencies up to 1048 W/g{sub Fe} (36.5 kA/m, 341 kHz; ILP=2.3 nH m{sup 2} kg{sup −1}) were obtained, which represent one of the highest values reported for iron oxide particles synthesized by co-precipitation without size-selective fractionation. Furthermore, particles reached SAR values of up to 719 W/g{sub Fe} (36.5 kA/m, 341 kHz; ILP=1.6 nH m{sup 2} kg{sup −1}) when in a solid matrix, demonstrating they were capable of significant rates of energy dissipation even when restricted from physical rotation. Reduction in energy dissipation rate due to immobilization has been identified as an obstacle to clinical translation of MFH. Hence, particles obtained with the conditions reported here have great potential for application in nanoscale thermal

  19. Ship Detection in GF-3 NSC Mode SAR Images

    Directory of Open Access Journals (Sweden)

    Liu Zeyu

    2017-10-01

    Full Text Available GF-3, the first C-band full-polarimetric Synthetic Aperture Radar (SAR satellite with a space resolution up to 1 m, has multiple strip and scan imaging modes. In this paper, we propose a maritime ship detection algorithm that detects ship targets via pixel classification in a Bayesian framework and employ effective enhancement methods to improve detection performance based on the data characteristics. We compare and analyze the results of detection experiments using the proposed algorithm with those of several Constant False Alarm Rate (CFAR algorithms. The experimental results verify the effectiveness of the proposed algorithm.

  20. Effects of angiotensin II and ionomycin on fluid and bicarbonate absorption in the rat proximal tubule

    International Nuclear Information System (INIS)

    Chatsudthipong, V.; Chan, Y.L.

    1986-01-01

    Microperfusion of proximal convoluted tubule(PCT) and peritubular capillaries was performed to examine the effects of angiotensin II(Ang II) and ionomycin on fluid and bicarbonate absorption. Bicarbonate was determined by microcalorimetry and C-14 inulin was used as a volume marker. The rates of bicarbonate absorption (JHCO 3 ) was 143 peq/min x mm and fluid absorption(Jv) was 2.70 nl/min x mm, when PCT and capillary perfusate contained normal Ringer solution. Addition of Ang II (10 -6 M) to the capillary perfusate caused reductions of JHCO 3 and Jv by 35%. A similar effect was observed when ionomycin was added to the capillary perfusate. Ang II antagonist, (Sar 1 , Ile 8 )-Angiotensin II(10 -6 M), completely blocked the inhibitory effect of Ang II on Jv and JHCO 3 . Removal of calcium from both luminal and capillary perfusate did not change the effect of Ang II on Jv and JHCO 3 . Our results indicate that Ang II inhibits the sodium-hydrogen exchanger in the proximal tubule via interacting with angiotensin receptor. The mechanism of Ang II action may involve mobilization of intracellular calcium

  1. NLP modeling for the optimization of LiBr-H2O absorption refrigeration systems with exergy loss rate, heat transfer area, and cost as single objective functions

    DEFF Research Database (Denmark)

    Mussati, Sergio F.; Gernaey, Krist; Morosuk, Tatiana

    2016-01-01

    exergy loss rate, the total heat transfer area, and the total annual cost of the system. It was found that the optimal solution obtained by minimization of the total exergy loss rate provides “theoretical” upper bounds not only for the total heat transfer area of the system but also for each process unit...... and all stream temperatures, while the optimal solution obtained by minimization of the total heat transfer area provides the lower bounds for these model variables, to solve a cost optimization problem. The minimization of the total exergy loss rate by varying parametrically the available total heat...... transfer area between these bounds was also performed, allowing to see how the optimal distribution of the available total heat transfer area among the system components, as well as the operating conditions (stream temperature, pressure, composition, and mass flow rate) and heat loads, vary qualitatively...

  2. Resilience of SAR11 bacteria to rapid acidification in the high-latitude open ocean.

    Science.gov (United States)

    Hartmann, Manuela; Hill, Polly G; Tynan, Eithne; Achterberg, Eric P; Leakey, Raymond J G; Zubkov, Mikhail V

    2016-02-01

    Ubiquitous SAR11 Alphaproteobacteria numerically dominate marine planktonic communities. Because they are excruciatingly difficult to cultivate, there is comparatively little known about their physiology and metabolic responses to long- and short-term environmental changes. As surface oceans take up anthropogenic, atmospheric CO2, the consequential process of ocean acidification could affect the global biogeochemical significance of SAR11. Shipping accidents or inadvertent release of chemicals from industrial plants can have strong short-term local effects on oceanic SAR11. This study investigated the effect of 2.5-fold acidification of seawater on the metabolism of SAR11 and other heterotrophic bacterioplankton along a natural temperature gradient crossing the North Atlantic Ocean, Norwegian and Greenland Seas. Uptake rates of the amino acid leucine by SAR11 cells as well as other bacterioplankton remained similar to controls despite an instant ∼50% increase in leucine bioavailability upon acidification. This high physiological resilience to acidification even without acclimation, suggests that open ocean dominant bacterioplankton are able to cope even with sudden and therefore more likely with long-term acidification effects. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  3. Factors associated with nosocomial SARS-CoV transmission among healthcare workers in Hanoi, Vietnam, 2003.

    Science.gov (United States)

    Reynolds, Mary G; Anh, Bach Huy; Thu, Vu Hoang; Montgomery, Joel M; Bausch, Daniel G; Shah, J Jina; Maloney, Susan; Leitmeyer, Katrin C; Huy, Vu Quang; Horby, Peter; Plant, Aileen Y; Uyeki, Timothy M

    2006-08-14

    In March of 2003, an outbreak of Severe Acute Respiratory Syndrome (SARS) occurred in Northern Vietnam. This outbreak began when a traveler arriving from Hong Kong sought medical care at a small hospital (Hospital A) in Hanoi, initiating a serious and substantial transmission event within the hospital, and subsequent limited spread within the community. We surveyed Hospital A personnel for exposure to the index patient and for symptoms of disease during the outbreak. Additionally, serum specimens were collected and assayed for antibody to SARS-associated coronavirus (SARS-CoV) antibody and job-specific attack rates were calculated. A nested case-control analysis was performed to assess risk factors for acquiring SARS-CoV infection. One hundred and fifty-three of 193 (79.3%) clinical and non-clinical staff consented to participate. Excluding job categories with job categories and activities associated with increased risk for SARS-CoV infection and demonstrates that a broad diversity of hospital workers may be vulnerable during an outbreak. These findings may help guide recommendations for the protection of vulnerable occupational groups and may have implications for other respiratory infections such as influenza.

  4. Landslide Mapping in Vegetated Areas Using Change Detection Based on Optical and Polarimetric SAR Data

    Directory of Open Access Journals (Sweden)

    Simon Plank

    2016-04-01

    Full Text Available Mapping of landslides, quickly providing information about the extent of the affected area and type and grade of damage, is crucial to enable fast crisis response, i.e., to support rescue and humanitarian operations. Most synthetic aperture radar (SAR data-based landslide detection approaches reported in the literature use change detection techniques, requiring very high resolution (VHR SAR imagery acquired shortly before the landslide event, which is commonly not available. Modern VHR SAR missions, e.g., Radarsat-2, TerraSAR-X, or COSMO-SkyMed, do not systematically cover the entire world, due to limitations in onboard disk space and downlink transmission rates. Here, we present a fast and transferable procedure for mapping of landslides, based on change detection between pre-event optical imagery and the polarimetric entropy derived from post-event VHR polarimetric SAR data. Pre-event information is derived from high resolution optical imagery of Landsat-8 or Sentinel-2, which are freely available and systematically acquired over the entire Earth’s landmass. The landslide mapping is refined by slope information from a digital elevation model generated from bi-static TanDEM-X imagery. The methodology was successfully applied to two landslide events of different characteristics: A rotational slide near Charleston, West Virginia, USA and a mining waste earthflow near Bolshaya Talda, Russia.

  5. An improved MIMO-SAR simulator strategy with ray tracing

    Science.gov (United States)

    Xiang, Xingyu; Mo, Zijian; Wang, Zhonghai; Chen, Genshe; Pham, Khanh; Blasch, Erik

    2016-05-01

    High resolution and wide-swath imaging can be obtained by Multiple-Input Multiple-Output (MIMO) synthetic aperture radar (SAR) with the state of the art technologies. The time division multiple access (TDMA) MIMO SAR mimics the motion of the antenna of SAR systems by switching the array channels to transmit the radar signals at different time slots. In this paper, we develop a simulation tool with ray tracing techniques to retrieve high resolution and accurate SAR images for development of MIMO SAR imaging methods. Without loss of generality, in the proposed simulator, we apply a TDMA MIMO SAR system with 13 transmitting antennas and 8 receiving antennas, where all transmitting antennas share a single transmitter and the receiving antennas share a single receiver. By comparing with the normal simulation MIMO SAR strategies, the simulation image using ray tracing results validate that the proposed method provides more accurate and higher resolution SAR images.

  6. Accelerated Scientific InSAR Processing, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Neva Ridge Technologies proposes to develop a suite of software tools for the analysis of SAR and InSAR data, focused on having a robust and adopted capability well...

  7. Investigating Seed Germination Indices and Absorption Rate of Sodium, Chloride, Calcium, and Potassium in Different Parts of Seedlings of Sweet Corn KSC 403 (Zea Mays L var. Saccharata Under Salinity Stress and Seed Priming

    Directory of Open Access Journals (Sweden)

    M. Nasrolah alhossini,

    2014-02-01

    Full Text Available To investigate the effects of different levels of seed priming on germination indices and nutrient absorption at early growth stages of sweet corn (Golden Kernel Hybrid a factorial experiment based on completely randomized design was conducted with three replications in 2011. The experiment consists of 6 levels of primings (seeds without priming, priming with tap water, priming with distilled water, priming with sodium chloride, potassium chloride, and hydrous calcium chloride and five levels of salinity (zero, 4, 8, 12 and 16 ds/m sodium chloride. The characteristics studied were germination percentage, germination rate, root and shoot length, fresh weight and dry weight of seedling, root to shoot ratio and determination of sodium, chloride, calcium, and potassium concentration in different parts of seedlings (stems, roots and seed. The results indicated that increasing salinity stress levels decreased all parameters measured. Priming seeds with hydrated calcium chloride responded to significantly to salinity stress better than other treatments. Results also showed that increasing concentration of sodium chloride salt, increased absorption rate of sodium but concentration of calcium and potassium were reduced. Because application of hydrous calcium chloride stimulates cell in using calcium under salinity conditions it leads to improved seedling growth parameters. To achieve a more accurate results slicing interaction effect of seed priming×salinity levels was performed. Hydrous calcium chloride treatments improved all traits under study except sodium and potassium concentration. This represents a better performance of seeds germination under salinity stress when seeds primed with hydrous calcium chloride.

  8. Coastal sea-level in Norway from CryoSat-2 SAR altimetry

    DEFF Research Database (Denmark)

    Idžanović, Martina; Ophaug, Vegard; Andersen, Ole Baltazar

    , mountains, and deep, narrow fjords. As the first of its kind, the European Space Agency's CryoSat-2 satellite carries a Synthetic aperture Interferometric Radar ALtimeter (SIRAL) which can operate in Synthetic Aperture Radar (SAR), SAR Interferometric (SARIn), as well as conventional Low Rate (LR) modes....... When operating in SARIn mode, the altimeter measures the phase difference of the backscattered signal at two antennas, from which the position of any backscattered point may be derived. Thus, the SARIn mode may help discriminating and mitigating land contamination signals from off-nadir land targets (e....... We therefore investigate the potential for CryoSat-2 data to provide improved ocean measurements in the Norwegian coastal zone. In particular, we make use of CryoSat-2's SAR and SARIn modes and determine coastal sea surface heights in specific coastal regions, and compare results with independent sea...

  9. Estimation and Removing of Anisotropic Scattering for Multiaspect Polarimetric SAR Image

    Directory of Open Access Journals (Sweden)

    Li Yang

    2015-06-01

    Full Text Available Multiaspect Synthetic Aperture Radar (SAR can generate high resolution images and target scattering signatures in different azimuth angles from the coherent integration of all subaperture images. However, mixed anisotropic scatters limit the application of traditional imaging theory. Anisotropic scattering may introduce errors in polarimetric parameters by decreasing the reliability of terrain classification and detection of variability. Thus a method is proposed for estimating and removing anisotropic scattering in multiaspect polarimetric SAR images. The proposed algorithm is based on the maximum likelihood and likelihood-ratio tests for the two-class case, while considering the speckle effect, the mechanism of removing the anisotropic scattering, and the monotonicity of the Constant False Alarm Rate (CFAR detection function. We compare the polarimetric entropy before and after removing the anisotropic subapertures, and then validate the algorithm's potential in retrieving the target signature using a P-band quad-pol airborne SAR with circular trajectory.

  10. Doppler Centroid Estimation for Airborne SAR Supported by POS and DEM

    Directory of Open Access Journals (Sweden)

    CHENG Chunquan

    2015-05-01

    Full Text Available It is difficult to estimate the Doppler frequency and modulating rate for airborne SAR by using traditional vector method due to instable flight and complex terrain. In this paper, it is qualitatively analyzed that the impacts of POS, DEM and their errors on airborne SAR Doppler parameters. Then an innovative vector method is presented based on the range-coplanarity equation to estimate the Doppler centroid taking the POS and DEM as auxiliary data. The effectiveness of the proposed method is validated and analyzed via the simulation experiments. The theoretical analysis and experimental results show that the method can be used to estimate the Doppler centroid with high accuracy even in the cases of high relief, instable flight, and large squint SAR.

  11. Stop outbreak of SARS with infrared cameras

    Science.gov (United States)

    Wu, Yigang M.

    2004-04-01

    SARS (Severe Acute Respiratory Syndrome, commonly known as Atypical Pneumonia in mainland China) caused 8422 people affected and resulting in 918 deaths worldwide in half year. This disease can be transmitted by respiratory droplets or by contact with a patient's respiratory secretions. This means it can be spread out very rapidly through the public transportations by the travelers with the syndrome. The challenge was to stop the SARS carriers traveling around by trains, airplanes, coaches and etc. It is impractical with traditional oral thermometers or spot infrared thermometers to screen the tens of travelers with elevated body temperature from thousands of normal travelers in hours. The thermal imager with temperature measurement function is a logical choice for this special application although there are some limitations and drawbacks. This paper discusses the real SARS applications of industrial infrared cameras in China from April to July 2003.

  12. Infrastructure monitoring with spaceborne SAR sensors

    CERN Document Server

    ANGHEL, ANDREI; CACOVEANU, REMUS

    2017-01-01

    This book presents a novel non-intrusive infrastructure monitoring technique based on the detection and tracking of scattering centers in spaceborne SAR images. The methodology essentially consists of refocusing each available SAR image on an imposed 3D point cloud associated to the envisaged infrastructure element and identifying the reliable scatterers to be monitored by means of four dimensional (4D) tomography. The methodology described in this book provides a new perspective on infrastructure monitoring with spaceborne SAR images, is based on a standalone processing chain, and brings innovative technical aspects relative to conventional approaches. The book is intended primarily for professionals and researchers working in the area of critical infrastructure monitoring by radar remote sensing.

  13. Bistatic SAR: State of the Art and Development Trend

    OpenAIRE

    Zeng Tao

    2012-01-01

    Bistatic SAR (BiSAR) systems have attracted the interests from global researchers and become a hotspot in the international radar community due to the progress of radar technology and rapidly increased applications nowadays. Based on the BiSAR experiments and breakthrough of the key technology, the paper summarized the general progresses of BiSAR systems, especially in European radar community, from different aspects such as system design, processing idea and topology etc. Different bistatic ...

  14. Monitoring Building Deformation with InSAR: Experiments and Validation

    OpenAIRE

    Kui Yang; Li Yan; Guoman Huang; Chu Chen; Zhengpeng Wu

    2016-01-01

    Synthetic Aperture Radar Interferometry (InSAR) techniques are increasingly applied for monitoring land subsidence. The advantages of InSAR include high accuracy and the ability to cover large areas; nevertheless, research validating the use of InSAR on building deformation is limited. In this paper, we test the monitoring capability of the InSAR in experiments using two landmark buildings; the Bohai Building and the China Theater, located in Tianjin, China. They were selected as real example...

  15. Applications of SAR Interferometry in Earth and Environmental Science Research

    OpenAIRE

    Zhou, Xiaobing; Chang, Ni-Bin; Li, Shusun

    2009-01-01

    This paper provides a review of the progress in regard to the InSAR remote sensing technique and its applications in earth and environmental sciences, especially in the past decade. Basic principles, factors, limits, InSAR sensors, available software packages for the generation of InSAR interferograms were summarized to support future applications. Emphasis was placed on the applications of InSAR in seismology, volcanology, land subsidence/uplift, landslide, glaciology, hydrology, and forestr...

  16. Pre-processing SAR image stream to facilitate compression for transport on bandwidth-limited-link

    Science.gov (United States)

    Rush, Bobby G.; Riley, Robert

    2015-09-29

    Pre-processing is applied to a raw VideoSAR (or similar near-video rate) product to transform the image frame sequence into a product that resembles more closely the type of product for which conventional video codecs are designed, while sufficiently maintaining utility and visual quality of the product delivered by the codec.

  17. Exploring cloud and big data components for SAR archiving and analysis

    Science.gov (United States)

    Baker, S.; Crosby, C. J.; Meertens, C.; Phillips, D.

    2017-12-01

    Under the Geodesy Advancing Geoscience and EarthScope (GAGE) NSF Cooperative Agreement, UNAVCO has seen the volume of the SAR Data Archive grow at a substantial rate, from 2 TB in Y1 and 5 TB in Y2 to 41 TB in Y3 primarily due to WInSAR PI proposal management of ALOS-­2/JAXA (Japan Aerospace Exploration Agency) data and to a lesser extent Supersites and other data collections. JAXA provides a fixed number of scenes per year for each PI, and some data files are 50­-60GB each, which accounts for the large volume of data. In total, over 100TB of SAR data are in the WInSAR/UNAVCO archive and a large portion of these are available unrestricted for WInSAR members. In addition to the existing data, newer data streams from the Sentinel-1 and NISAR missions will require efficient processing pipelines and easily scalable infrastructure to handle processed results. With these growing data sizes and space concerns, the SAR archive operations migrated to the Texas Advanced Computing Center (TACC) via an NSF XSEDE proposal in spring 2017. Data are stored on an HPC system while data operations are running on Jetstream virtual machines within the same datacenter. In addition to the production data operations, testing was done in early 2017 with container based InSAR processing analysis using JupyterHub and Docker images deployed on a VM cluster on Jetstream. The JupyterHub environment is well suited for short courses and other training opportunities for the community such as labs for university courses on InSAR. UNAVCO is also exploring new processing methodologies using DC/OS (the datacenter operating system) for batch and stream processing workflows and time series analysis with Big Data open source components like the Spark, Mesos, Akka, Cassandra, Kafka (SMACK) stack. The comparison of the different methodologies will provide insight into the pros and cons for each and help the SAR community with decisions about infrastructure and software requirements to meet their research

  18. Enhancement of SAR images using fuzzy shrinkage technique in ...

    Indian Academy of Sciences (India)

    The synthetic aperture radar (SAR) images are mainly affected by speckle noise. Speckle degrades the features in the image and reduces the ability of a human observer to resolve fine detail, hence despeckling is very much required for SAR images. This paper presents speckle noise reduction in SAR images using a ...

  19. Satellite sar detection of hurricane helene (2006)

    DEFF Research Database (Denmark)

    Ju, Lian; Cheng, Yongcun; Xu, Qing

    2013-01-01

    In this paper, the wind structure of hurricane Helene (2006) over the Atlantic Ocean is investigated from a C-band RADARSAT-1 synthetic aperture radar (SAR) image acquired on 20 September 2006. First, the characteristics, e.g., the center, scale and area of the hurricane eye (HE) are determined. ...... observations from the stepped frequency microwave radiometer (SFMR) on NOAA P3 aircraft. All the results show the capability of hurricane monitoring by satellite SAR. Copyright © 2013 by the International Society of Offshore and Polar Engineers (ISOPE)....

  20. The planned Alaska SAR Facility - An overview

    Science.gov (United States)

    Carsey, Frank; Weeks, Wilford

    1987-01-01

    The Alaska SAR Facility (ASF) is described in an overview fashion. The facility consists of three major components, a Receiving Ground System, a SAR Processing System and an Analysis and Archiving System; the ASF Program also has a Science Working Team and the requisite management and operations systems. The ASF is now an approved and fully funded activity; detailed requirements and science background are presented for the facility to be implemented for data from the European ERS-1, the Japanese ERS-1 and Radarsat.

  1. Science data collection with polarimetric SAR

    DEFF Research Database (Denmark)

    Dall, Jørgen; Woelders, Kim; Madsen, Søren Nørvang

    1996-01-01

    Discusses examples on the use of polarimetric SAR in a number of Earth science studies. The studies are presently being conducted by the Danish Center for Remote Sensing. A few studies of the European Space Agency's EMAC programme are also discussed. The Earth science objectives are presented......, and the potential of polarimetric SAR is discussed and illustrated with data collected by the Danish airborne EMISAR system during a number of experiments in 1994 and 1995. The presentation will include samples of data acquired for the different studies...

  2. Estimating IMU heading error from SAR images.

    Energy Technology Data Exchange (ETDEWEB)

    Doerry, Armin Walter

    2009-03-01

    Angular orientation errors of the real antenna for Synthetic Aperture Radar (SAR) will manifest as undesired illumination gradients in SAR images. These gradients can be measured, and the pointing error can be calculated. This can be done for single images, but done more robustly using multi-image methods. Several methods are provided in this report. The pointing error can then be fed back to the navigation Kalman filter to correct for problematic heading (yaw) error drift. This can mitigate the need for uncomfortable and undesired IMU alignment maneuvers such as S-turns.

  3. Geologic mapping in Greenland with polarimetric SAR

    DEFF Research Database (Denmark)

    Dall, Jørgen; Madsen, Søren Nørvang; Brooks, C. K.

    1995-01-01

    mapping is complicated by an extreme topography leading to massive shadowing, foreshortening and layover. An artifact characterised by high cross-polarisation is observed behind many sharp mountain ridges. A multi-reflection hypothesis has been investigated without finding the ultimate proof......The application of synthetic aperture radar (SAR) for geologic mapping in Greenland is investigated by the Danish Center for Remote Sensing (DCRS) in co-operation with the Danish Lithosphere Centre (DLC). In 1994 a pilot project was conducted in East Greenland. The Danish airborne SAR, EMISAR...

  4. Stellar Absorption Line Analysis of Local Star-forming Galaxies: The Relation between Stellar Mass, Metallicity, Dust Attenuation, and Star Formation Rate

    International Nuclear Information System (INIS)

    Jabran Zahid, H.; Kudritzki, Rolf-Peter; Ho, I-Ting; Conroy, Charlie; Andrews, Brett

    2017-01-01

    We analyze the optical continuum of star-forming galaxies in the Sloan Digital Sky Survey by fitting stacked spectra with stellar population synthesis models to investigate the relation between stellar mass, stellar metallicity, dust attenuation, and star formation rate. We fit models calculated with star formation and chemical evolution histories that are derived empirically from multi-epoch observations of the stellar mass–star formation rate and the stellar mass–gas-phase metallicity relations, respectively. We also fit linear combinations of single-burst models with a range of metallicities and ages. Star formation and chemical evolution histories are unconstrained for these models. The stellar mass–stellar metallicity relations obtained from the two methods agree with the relation measured from individual supergiant stars in nearby galaxies. These relations are also consistent with the relation obtained from emission-line analysis of gas-phase metallicity after accounting for systematic offsets in the gas-phase metallicity. We measure dust attenuation of the stellar continuum and show that its dependence on stellar mass and star formation rate is consistent with previously reported results derived from nebular emission lines. However, stellar continuum attenuation is smaller than nebular emission line attenuation. The continuum-to-nebular attenuation ratio depends on stellar mass and is smaller in more massive galaxies. Our consistent analysis of stellar continuum and nebular emission lines paves the way for a comprehensive investigation of stellar metallicities of star-forming and quiescent galaxies.

  5. Relic Neutrino Absorption Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Eberle, b

    2004-01-28

    Resonant annihilation of extremely high-energy cosmic neutrinos on big-bang relic anti-neutrinos (and vice versa) into Z-bosons leads to sizable absorption dips in the neutrino flux to be observed at Earth. The high-energy edges of these dips are fixed, via the resonance energies, by the neutrino masses alone. Their depths are determined by the cosmic neutrino background density, by the cosmological parameters determining the expansion rate of the universe, and by the large redshift history of the cosmic neutrino sources. We investigate the possibility of determining the existence of the cosmic neutrino background within the next decade from a measurement of these absorption dips in the neutrino flux. As a by-product, we study the prospects to infer the absolute neutrino mass scale. We find that, with the presently planned neutrino detectors (ANITA, Auger, EUSO, OWL, RICE, and SalSA) operating in the relevant energy regime above 10{sup 21} eV, relic neutrino absorption spectroscopy becomes a realistic possibility. It requires, however, the existence of extremely powerful neutrino sources, which should be opaque to nucleons and high-energy photons to evade present constraints. Furthermore, the neutrino mass spectrum must be quasi-degenerate to optimize the dip, which implies m{sub {nu}} 0.1 eV for the lightest neutrino. With a second generation of neutrino detectors, these demanding requirements can be relaxed considerably.

  6. Improving InSAR geodesy using Global Atmospheric Models

    Science.gov (United States)

    Jolivet, Romain; Agram, Piyush Shanker; Lin, Nina Y.; Simons, Mark; Doin, Marie-Pierre; Peltzer, Gilles; Li, Zhenghong

    2014-03-01

    Spatial and temporal variations of pressure, temperature, and water vapor content in the atmosphere introduce significant confounding delays in interferometric synthetic aperture radar (InSAR) observations of ground deformation and bias estimates of regional strain rates. Producing robust estimates of tropospheric delays remains one of the key challenges in increasing the accuracy of ground deformation measurements using InSAR. Recent studies revealed the efficiency of global atmospheric reanalysis to mitigate the impact of tropospheric delays, motivating further exploration of their potential. Here we explore the effectiveness of these models in several geographic and tectonic settings on both single interferograms and time series analysis products. Both hydrostatic and wet contributions to the phase delay are important to account for. We validate these path delay corrections by comparing with estimates of vertically integrated atmospheric water vapor content derived from the passive multispectral imager Medium-Resolution Imaging Spectrometer, onboard the Envisat satellite. Generally, the performance of the prediction depends on the vigor of atmospheric turbulence. We discuss (1) how separating atmospheric and orbital contributions allows one to better measure long-wavelength deformation and (2) how atmospheric delays affect measurements of surface deformation following earthquakes, and (3) how such a method allows us to reduce biases in multiyear strain rate estimates by reducing the influence of unevenly sampled seasonal oscillations of the tropospheric delay.

  7. SARS knowledge, perceptions, and behaviors: a comparison between Finns and the Dutch during the SARS outbreak in 2003

    NARCIS (Netherlands)

    Vartti, A.M.; Oenema, A.; Schreck, M.; Uutela, A.; Zwart, de O.; Brug, J.; Aro, A.R.

    2009-01-01

    BACKGROUND: The SARS outbreak served to test both local and international outbreak management and risk communication practices. PURPOSE: The study compares SARS knowledge, perceptions, behaviors, and information between Finns and the Dutch during the SARS outbreak in 2003. METHOD: The participants

  8. Combination of Conventional and Advanced DInSAR to Monitor Very Fast Mining Subsidence with TerraSAR-X Data: Bytom City (Poland

    Directory of Open Access Journals (Sweden)

    Maria Przyłucka

    2015-04-01

    Full Text Available In this work, the analysis of TerraSAR-X satellite images combining both conventional and advanced Differential Synthetic Aperture Radar Interferometry (DInSAR approaches has proven to be effective to detect and monitor fast evolving mining subsidence on urban areas in the Upper Silesian Coal Basin (Poland. This region accounts for almost three million inhabitants where mining subsidence has produced severe damage to urban structures and infrastructures in recent years. Conventional DInSAR approach was used to generate 28 differential interferograms between 5 July 2011 and 21 June 2012 identifying 31 subsidence troughs that account up to 245 mm of displacement in 54 days (equivalent to 1660 mm/year. SqueeSARTM processing yielded a very dense measurement point distribution, failing to detect faster displacements than 330 mm/year, which occur within the subsidence troughs detected with conventional DInSAR. Despite this limitation, this approach was useful to delimit stable areas where mining activities are not conducted and areas affected by residual subsidence surrounding the detected subsidence troughs. These residual subsidence mining areas are located approximately 1 km away from the 31 detected subsidence troughs and account for a subsidence rate greater than 17 mm/year on average. The validation of this methodology has been performed over Bytom City were underground mining activity produced severe damages in August 2011. Conventional DInSAR permitted to successfully map subsidence troughs between July and August 2011 that coincide spatially and temporally with the evolution of underground mining excavations, as well as with the demolition of 28 buildings of Karb district. Additionally, SqueeSARTM displacement estimates were useful to delimit an area of 8.3 km2 of Bytom city that is affected by a residual mining subsidence greater than 5 mm/year and could potentially suffer damages in the midterm. The comparison between geodetic data and

  9. Compact Polarimetric SAR Ship Detection with m-δ Decomposition Using Visual Attention Model

    Directory of Open Access Journals (Sweden)

    Lu Xu

    2016-09-01

    Full Text Available A few previous studies have illustrated the potentials of compact polarimetric Synthetic Aperture Radar (CP SAR in ship detection. In this paper, we design a ship detection algorithm of CP SAR from the perspective of computer vision. A ship detection algorithm using the pulsed cosine transform (PCT visual attention model is proposed to suppress background clutter and highlight conspicuous ship targets. It is the first time that a visual attention model is introduced to CP SAR application. The proposed algorithm is a quick and complete framework for practical use. Polarimetric features—the relative phase δ and volume scattering component—are extracted from m-δ decomposition to eliminate false alarms and modify the PCT model. The constant false alarm rate (CFAR algorithm based on lognormal distribution is adopted to detect ship targets, after a clutter distribution fitting procedure of the modified saliency map. The proposed method is then tested on three simulated circular-transmit-linear-receive (CTLR mode images, which covering East Sea of China. Compared with the detection results of SPAN and the saliency map with only single-channel amplitude, the proposed method achieves the highest detection rates and the lowest misidentification rate and highest figure of merit, proving the effectiveness of polarimetric information of compact polarimetric SAR ship detection and the enhancement from the visual attention model.

  10. The absorption effect of the Lα-line Supplement to the paper 'On the Correlation Between the Hα-line emission rate and the ablation rate of a hydrogen pellet in tokamak discharges' – Nuclear Fusion 24 (1984) 697

    DEFF Research Database (Denmark)

    Chang, C. T.; Thomsen, Kenneth

    1985-01-01

    Several assumptions made in a previous study of the correlation between the Hα-line emission rate and the ablation rate of a hydrogen pellet injected into a tokamak discharge showed that the emission layer of the ablatant as optically thin with respect to all levels of the principal quantum numbe...

  11. Estimating the Doppler centroid of SAR data

    DEFF Research Database (Denmark)

    Madsen, Søren Nørvang

    1989-01-01

    After reviewing frequency-domain techniques for estimating the Doppler centroid of synthetic-aperture radar (SAR) data, the author describes a time-domain method and highlights its advantages. In particular, a nonlinear time-domain algorithm called the sign-Doppler estimator (SDE) is shown to hav...

  12. What is Gammarus campylops of Sars, 1894

    NARCIS (Netherlands)

    Stock, J.H.; Kant, P.

    1966-01-01

    A revision of the specimens described by Sars, 1894, as Gammarus campylops Leach, 1814, proved that they did not belong to that species, nor to Gammarus ochlos Reid, 1945 (= G. sarsi Reid, 1943), as Reid believed. Reid’s species, of which also original specimens have been reexamined, is identical

  13. Discovery and SAR of hydantoin TACE inhibitors

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Wensheng; Guo, Zhuyan; Orth, Peter; Madison, Vincent; Chen, Lei; Dai, Chaoyang; Feltz, Robert J.; Girijavallabhan, Vinay M.; Kim, Seong Heon; Kozlowski, Joseph A.; Lavey, Brian J.; Li, Dansu; Lundell, Daniel; Niu, Xiaoda; Piwinski, John J.; Popovici-Muller, Janeta; Rizvi, Razia; Rosner, Kristin E.; Shankar, Bandarpalle B.; Shih, Neng-Yang; Siddiqui, M.A.; Sun, J.; Tong, L.; Umland, S.; Wong, M.K.; Yang, D.Y.; Zhou, G. (Merck)

    2010-09-03

    We disclose inhibitors of TNF-{alpha} converting enzyme (TACE) designed around a hydantoin zinc binding moiety. Crystal structures of inhibitors bound to TACE revealed monodentate coordination of the hydantoin to the zinc. SAR, X-ray, and modeling designs are described. To our knowledge, these are the first reported X-ray structures of TACE with a hydantoin zinc ligand.

  14. Target detection and recognition with polarimetric SAR

    NARCIS (Netherlands)

    Dekker, R.J.; Broek, A.C. van den

    2000-01-01

    Target detection and recognition using polarimetric SAR data has been studied by using PHARUS and RAMSES data collected during the MIMEX campaign. Additionally very high-resolution ISAR data was used. A basic detection and recognition scheme has been developed, which includes polarimetric

  15. SAR Image Despeckling Via Structural Sparse Representation

    Science.gov (United States)

    Lu, Ting; Li, Shutao; Fang, Leyuan; Benediktsson, Jón Atli

    2016-12-01

    A novel synthetic aperture radar (SAR) image despeckling method based on structural sparse representation is introduced. The proposed method utilizes the fact that different regions in SAR images correspond to varying terrain reflectivity. Therefore, SAR images can be split into a heterogeneous class (with a varied terrain reflectivity) and a homogeneous class (with a constant terrain reflectivity). In the proposed method, different sparse representation based despeckling schemes are designed by combining the different region characteristics in SAR images. For heterogeneous regions with rich structure and texture information, structural dictionaries are learned to appropriately represent varied structural characteristics. Specifically, each patch in these regions is sparsely coded with the best fitted structural dictionary, thus good structure preservation can be obtained. For homogenous regions without rich structure and texture information, the highly redundant photometric self-similarity is exploited to suppress speckle noise without introducing artifacts. That is achieved by firstly learning the sub-dictionary, then simultaneously sparsely coding for each group of photometrically similar image patches. Visual and objective experimental results demonstrate the superiority of the proposed method over the-state-of-the-art methods.

  16. CFAR Edge Detector for Polarimetric SAR Images

    DEFF Research Database (Denmark)

    Schou, Jesper; Skriver, Henning; Nielsen, Allan Aasbjerg

    2003-01-01

    Finding the edges between different regions in an image is one of the fundamental steps of image analysis, and several edge detectors suitable for the special statistics of synthetic aperture radar (SAR) intensity images have previously been developed. In this paper, a new edge detector for polar...

  17. Calculation of SAR and temperature rise in a high-resolution vascularized model of the human eye and orbit when exposed to a dipole antenna at 900, 1500 and 1800 MHz.

    Science.gov (United States)

    Flyckt, V M M; Raaymakers, B W; Kroeze, H; Lagendijk, J J W

    2007-05-21

    The eye is considered to be a critical organ when determining safety standards for radiofrequency radiation. With a detailed anatomy of the human eye and orbit inserted in a whole-head model, the specific absorption rates (SARs) and thermal effects were determined under exposure to a dipole antenna representing a mobile phone operating at 900, 1500 and 1800 MHz with an output power of 1 W. The temperature rise was calculated by taking the blood flow into account either by the Pennes bioheat model or by including the discrete vasculature (DIVA). In addition, a simple spherical model using constant heat transfer coefficients was used. Peak SARs in the humour are 4.5, 7.7 and 8.4 W kg(-1) for 900, 1500 and 1800 MHz respectively. Averaged over the whole eyeball, the SARs are 1.7, 2.5 and 2.2 W kg(-1). The maximum temperature rises in the eye due to the exposure are 0.22, 0.27 and 0.25 degrees C for exposure of 900, 1500 and 1800 MHz, respectively, calculated with DIVA. For the Pennes bioheat model, the temperature rises are slightly lower: 0.19, 0.24, 0.22 degrees C respectively. For the simple spherical model, the maximum temperature rises are 0.15, 0.22 and 0.20 degrees C. The peak temperature is located in the anterior part of the lens for 900 MHz and deeper in the eye for higher frequencies, and in the posterior part of the lens for 1500 MHz and close to the centre of the eyeball for 1800 MHz. For these RF safety applications, both DIVA and the Pennes bioheat model could be used to relate the SAR distributions to the resulting temperature distributions. Even though, for these artificial exposure conditions, the SAR values are not in compliance with safety guidelines, the maximum temperature rises in the eye are too small to give harmful effects. The temperature in the eye also remains below body core temperature.

  18. Peptide Mimicrying Between SARS Coronavirus Spike Protein and Human Proteins Reacts with SARS Patient Serum

    Directory of Open Access Journals (Sweden)

    K.-Y. Hwa

    2008-01-01

    Full Text Available Molecular mimicry, defined as similar structures shared by molecules from dissimilar genes or proteins, is a general strategy used by pathogens to infect host cells. Severe acute respiratory syndrome (SARS is a new human respiratory infectious disease caused by SARS coronavirus (SARS-CoV. The spike (S protein of SARS-CoV plays an important role in the virus entry into a cell. In this study, eleven synthetic peptides from the S protein were selected based on its sequence homology with human proteins. Two of the peptides D07 (residues 927–937 and D08 (residues 942–951 were recognized by the sera of SARS patients. Murine hyperimmune sera against these peptides bound to proteins of human lung epithelial cells A549. Another peptide D10 (residues 490–502 stimulated A549 to proliferate and secrete IL-8. The present results suggest that the selected S protein regions, which share sequence homology with human proteins, may play important roles in SARS-CoV infection.

  19. The Seamless SAR Archive (SSARA) Project and Other SAR Activities at UNAVCO

    Science.gov (United States)

    Baker, S.; Crosby, C. J.; Meertens, C. M.; Fielding, E. J.; Bryson, G.; Buechler, B.; Nicoll, J.; Baru, C.

    2014-12-01

    The seamless synthetic aperture radar archive (SSARA) implements a seamless distributed access system for SAR data and derived data products (i.e. interferograms). SSARA provides a unified application programming interface (API) for SAR data search and results at the Alaska Satellite Facility and UNAVCO (WInSAR and EarthScope data archives) through the use of simple web services. A federated query service was developed using the unified APIs, providing users a single search interface for both archives. Interest from the international community has prompted an effort to incorporate ESA's Virtual Archive 4 Geohazard Supersites and Natural Laboratories (GSNL) collections and other archives into the federated query service. SSARA also provides Digital Elevation Model access for topographic correction via a simple web service through OpenTopography and tropospheric correction products through JPL's OSCAR service. Additionally, UNAVCO provides data storage capabilities for WInSAR PIs with approved TerraSAR-X and ALOS-2 proposals which allows easier distribution to US collaborators on associated proposals and facilitates data access through the SSARA web services. Further work is underway to incorporate federated data discovery for GSNL across SAR, GPS, and seismic datasets provided by web services from SSARA, GSAC, and COOPEUS.

  20. Signal Processing for a Multiple-Input, Multiple-Output (MIMO Video Synthetic Aperture Radar (SAR with Beat Frequency Division Frequency-Modulated Continuous Wave (FMCW

    Directory of Open Access Journals (Sweden)

    Seok Kim

    2017-05-01

    Full Text Available In this paper, we present a novel signal processing method for video synthetic aperture radar (ViSAR systems, which are suitable for operation in unmanned aerial vehicle (UAV environments. The technique improves aspects of the system’s performance, such as the frame rate and image size of the synthetic aperture radar (SAR video. The new ViSAR system is based on a frequency-modulated continuous wave (FMCW SAR structure that is combined with multiple-input multiple-output (MIMO technology, and multi-channel azimuth processing techniques. FMCW technology is advantageous for use in low cost, small size, and lightweight systems, like small UAVs. MIMO technology is utilized for increasing the equivalent number of receiving channels in the azimuthal direction, and reducing aperture size. This effective increase is achieved using a co-array concept by means of beat frequency division (BFD FMCW. A multi-channel azimuth processing technique is used for improving the frame rate and image size of SAR video, by suppressing the azimuth ambiguities in the receiving channels. This paper also provides analyses of the frame rate and image size of SAR video of ViSAR systems. The performance of the proposed system is evaluated using an exemplary system. The results of analyses are presented, and their validity is verified using numerical simulations.

  1. Investigating subsidence at volcanoes in northern California using InSAR

    Science.gov (United States)

    Parker, A. L.; Biggs, J.; Annen, C.; Lu, Z.

    2013-12-01

    Both Medicine Lake Volcano (MLV) and Lassen Volcanic Center (LVC), northern CA, show signs of subsidence at rates of ~1 cm/yr. Leveling and campaign GPS measurements show that MLV has subsided at a constant rate for over 50 years, making the geodetic history of this volcano unique in both its duration and continuity. Here, we summarise and build upon the existing geodetic records at MLV and LVC, using interferometric synthetic aperture radar (InSAR) to extend the time-series of deformation measurements to 2011. We also use the improved spatial resolution of InSAR measurements to investigate causes of long-term subsidence, providing new insight into magmatic storage conditions at MLV and the timescales of deformation due to cooling and crystallization. A large InSAR dataset has been acquired for the volcanoes of northern CA, but application of the data has been limited by extensive noise and incoherence. We analyse multiple datasets from MLV and LVC and, with the use of multi-temporal InSAR analysis methods (noise-based stacking, π-RATE and StaMPS), demonstrate how InSAR may be used more successfully as a monitoring tool in this region. By comparing InSAR results for MLV to past geodetic studies, we demonstrate that subsidence is on going at ~1 cm/yr with no detectable change in rate. We find that the best fitting source geometry to InSAR data is a sill approximated by a horizontal penny-shaped crack, with radius 2 km and depth 11 km, undergoing volume loss at a rate of -0.0022 km3/yr. We discuss possible source mechanisms of long-term subsidence, investigating volume loss due to cooling and crystallization of an intrusion. We calculate the temperature, melt fraction and volume loss of an intrusion over time using petrological information and a numerical thermal model of heat loss by conduction. The geometry of the intrusion is based upon the depth and radius of the penny-shaped crack model. We run simulations for a range of thicknesses between that of a single

  2. SAR Raw Data Generation for Complex Airport Scenes

    Directory of Open Access Journals (Sweden)

    Jia Li

    2014-10-01

    Full Text Available The method of generating the SAR raw data of complex airport scenes is studied in this paper. A formulation of the SAR raw signal model of airport scenes is given. Via generating the echoes from the background, aircrafts and buildings, respectively, the SAR raw data of the unified SAR imaging geometry is obtained from their vector additions. The multipath scattering and the shadowing between the background and different ground covers of standing airplanes and buildings are analyzed. Based on the scattering characteristics, coupling scattering models and SAR raw data models of different targets are given, respectively. A procedure is given to generate the SAR raw data of airport scenes. The SAR images from the simulated raw data demonstrate the validity of the proposed method.

  3. Immunization with SARS coronavirus vaccines leads to pulmonary immunopathology on challenge with the SARS virus.

    Directory of Open Access Journals (Sweden)

    Chien-Te Tseng

    Full Text Available Severe acute respiratory syndrome (SARS emerged in China in 2002 and spread to other countries before brought under control. Because of a concern for reemergence or a deliberate release of the SARS coronavirus, vaccine development was initiated. Evaluations of an inactivated whole virus vaccine in ferrets and nonhuman primates and a virus-like-particle vaccine in mice induced protection against infection but challenged animals exhibited an immunopathologic-type lung disease.Four candidate vaccines for humans with or without alum adjuvant were evaluated in a mouse model of SARS, a VLP vaccine, the vaccine given to ferrets and NHP, another whole virus vaccine and an rDNA-produced S protein. Balb/c or C57BL/6 mice were vaccinated i.m. on day 0 and 28 and sacrificed for serum antibody measurements or challenged with live virus on day 56. On day 58, challenged mice were sacrificed and lungs obtained for virus and histopathology.All vaccines induced serum neutralizing antibody with increasing dosages and/or alum significantly increasing responses. Significant reductions of SARS-CoV two days after challenge was seen for all vaccines and prior live SARS-CoV. All mice exhibited histopathologic changes in lungs two days after challenge including all animals vaccinated (Balb/C and C57BL/6 or given live virus, influenza vaccine, or PBS suggesting infection occurred in all. Histopathology seen in animals given one of the SARS-CoV vaccines was uniformly a Th2-type immunopathology with prominent eosinophil infiltration, confirmed with special eosinophil stains. The pathologic changes seen in all control groups lacked the eosinophil prominence.These SARS-CoV vaccines all induced antibody and protection against infection with SARS-CoV. However, challenge of mice given any of the vaccines led to occurrence of Th2-type immunopathology suggesting hypersensitivity to SARS-CoV components was induced. Caution in proceeding to application of a SARS-CoV vaccine in

  4. Post-Eruptive Inflation of Okmok Volcano, Alaska, from InSAR, 2008–2014

    Directory of Open Access Journals (Sweden)

    Feifei Qu

    2015-12-01

    Full Text Available Okmok, a ~10-km wide caldera that occupies most of the northeastern end of Umnak Island, is one of the most active volcanoes in the Aleutian arc. The most recent eruption at Okmok during July–August 2008 was by far its largest and most explosive since at least the early 19th century. We investigate post-eruptive magma supply and storage at the volcano during 2008–2014 by analyzing all available synthetic aperture radar (SAR images of Okmok acquired during that time period using the multi-temporal InSAR technique. Data from the C-band Envisat and X-band TerraSAR-X satellites indicate that Okmok started inflating very soon after the end of 2008 eruption at a time-variable rate of 48–130 mm/y, consistent with GPS measurements. The “model-assisted” phase unwrapping method is applied to improve the phase unwrapping operation for long temporal baseline pairs. The InSAR time-series is used as input for deformation source modeling, which suggests magma accumulating at variable rates in a shallow storage zone at ~3.9 km below sea level beneath the summit caldera, consistent with previous studies. The modeled volume accumulation in the six years following the 2008 eruption is ~75% of the 1997 eruption volume and ~25% of the 2008 eruption volume.

  5. Post-eruptive inflation of Okmok Volcano, Alaska, from InSAR, 2008–2014

    Science.gov (United States)

    Qu, Feifei; Lu, Zhong; Poland, Michael; Freymueller, Jeffrey T.; Zhang, Qin; Jung, Hyung-Sup

    2016-01-01

    Okmok, a ~10-km wide caldera that occupies most of the northeastern end of Umnak Island, is one of the most active volcanoes in the Aleutian arc. The most recent eruption at Okmok during July-August 2008 was by far its largest and most explosive since at least the early 19th century. We investigate post-eruptive magma supply and storage at the volcano during 2008–2014 by analyzing all available synthetic aperture radar (SAR) images of Okmok acquired during that time period using the multi-temporal InSAR technique. Data from the C-band Envisat and X-band TerraSAR-X satellites indicate that Okmok started inflating very soon after the end of 2008 eruption at a time-variable rate of 48-130 mm/y, consistent with GPS measurements. The “model-assisted” phase unwrapping method is applied to improve the phase unwrapping operation for long temporal baseline pairs. The InSAR time-series is used as input for deformation source modeling, which suggests magma accumulating at variable rates in a shallow storage zone at ~3.9 km below sea level beneath the summit caldera, consistent with previous studies. The modeled volume accumulation in the 6 years following the 2008 eruption is ~75% of the 1997 eruption volume and ~25% of the 2008 eruption volume.

  6. Probability of detection of downed aircraft using SAR polarimetry

    Science.gov (United States)

    Chotoo, Kancham; Huxtable, Barton D.; Mansfield, Arthur W.; Rais, Houra

    2000-08-01

    In developing a beaconless search and rescue capability to quickly locate small aircraft that have crashed in remote areas, NASA's Search and Rescue Synthetic Aperture Radar (SAR2) program brings together advanced polarimetric synthetic aperture radar processing, field and laboratory tests, and state-of-the-art automated target detection algorithms. The fundamental idea underlying the search and rescue (S&R) approach is use of an airborne polarimetric radar. The downed aircraft is partly composed of metal, and consists of regular geometric shapes such as flat plates, dihedrals, trihedrals, etc., which produce a polarization signature expected to be distinct from that of surrounding terrain and foliage. Onboard polarimetric SAR image formation combined with automatic image exploitation will ultimately cue the S&R team to candidate crash sites in near real-time. We empirically examine the probability of detection (PD) and false alarm rate (FAR) for crash site detection using polarimetry to discriminate between aircraft target signatures within natural clutter. This briefing will present the latest results from the S&R Program activities, providing an update to the last program presentation to the SPIE Meeting in 1999.

  7. Transfer Learning with Convolutional Neural Networks for SAR Ship Recognition

    Science.gov (United States)

    Zhang, Di; Liu, Jia; Heng, Wang; Ren, Kaijun; Song, Junqiang

    2018-03-01

    Ship recognition is the backbone of marine surveillance systems. Recent deep learning methods, e.g. Convolutional Neural Networks (CNNs), have shown high performance for optical images. Learning CNNs, however, requires a number of annotated samples to estimate numerous model parameters, which prevents its application to Synthetic Aperture Radar (SAR) images due to the limited annotated training samples. Transfer learning has been a promising technique for applications with limited data. To this end, a novel SAR ship recognition method based on CNNs with transfer learning has been developed. In this work, we firstly start with a CNNs model that has been trained in advance on Moving and Stationary Target Acquisition and Recognition (MSTAR) database. Next, based on the knowledge gained from this image recognition task, we fine-tune the CNNs on a new task to recognize three types of ships in the OpenSARShip database. The experimental results show that our proposed approach can obviously increase the recognition rate comparing with the result of merely applying CNNs. In addition, compared to existing methods, the proposed method proves to be very competitive and can learn discriminative features directly from training data instead of requiring pre-specification or pre-selection manually.

  8. Very low rate compression of speckled SAR imagery

    Energy Technology Data Exchange (ETDEWEB)

    Eichel, P.H. [Sandia National Labs., Albuquerque, NM (United States); Ives, R.W. [Navy (United States)

    1998-01-01

    Synthetic aperture radars produce coherent, and speckled, high resolution images of the ground. Because modern systems can generate large amounts of imagery, there is substantial interest in applying image compression techniques to these products. In this paper, the authors examine the properties of speckled imagery relevant to the task of data compression. In particular, they demonstrate the advisability of compressing the speckle mean function rather than the literal image. The theory, methodology, and an example are presented.

  9. Absorption properties of identical atoms

    International Nuclear Information System (INIS)

    Sancho, Pedro

    2013-01-01

    Emission rates and other optical properties of multi-particle systems in collective and entangled states differ from those in product ones. We show the existence of similar effects in the absorption probabilities for (anti)symmetrized states of two identical atoms. The effects strongly depend on the overlapping between the atoms and differ for bosons and fermions. We propose a viable experimental verification of these ideas. -- Highlights: •The absorption rates of a pair of identical atoms in product and (anti)symmetrized states are different. •The modifications of the optical properties are essentially determined by the overlapping between the atoms. •The absorption properties differ, in some cases, for bosons and fermions

  10. Spaceborne Polarimetric SAR Interferometry: Performance Analysis and Mission Concepts

    Directory of Open Access Journals (Sweden)

    Shane R. Cloude

    2005-12-01

    Full Text Available We investigate multichannel imaging radar systems employing coherent combinations of polarimetry and interferometry (Pol-InSAR. Such systems are well suited for the extraction of bio- and geophysical parameters by evaluating the combined scattering from surfaces and volumes. This combination leads to several important differences between the design of Pol-InSAR sensors and conventional single polarisation SAR interferometers. We first highlight these differences and then investigate the Pol-InSAR performance of two proposed spaceborne SAR systems (ALOS/PalSAR and TerraSAR-L operating in repeat-pass mode. For this, we introduce the novel concept of a phase tube which enables (1 a quantitative assessment of the Pol-InSAR performance, (2 a comparison between different sensor configurations, and (3 an optimization of the instrument settings for different Pol-InSAR applications. The phase tube may hence serve as an interface between system engineers and application-oriented scientists. The performance analysis reveals major limitations for even moderate levels of temporal decorrelation. Such deteriorations may be avoided in single-pass sensor configurations and we demonstrate the potential benefits from the use of future bi- and multistatic SAR interferometers.

  11. Spaceborne Polarimetric SAR Interferometry: Performance Analysis and Mission Concepts

    Science.gov (United States)

    Krieger, Gerhard; Papathanassiou, Konstantinos Panagiotis; Cloude, Shane R.

    2005-12-01

    We investigate multichannel imaging radar systems employing coherent combinations of polarimetry and interferometry (Pol-InSAR). Such systems are well suited for the extraction of bio- and geophysical parameters by evaluating the combined scattering from surfaces and volumes. This combination leads to several important differences between the design of Pol-InSAR sensors and conventional single polarisation SAR interferometers. We first highlight these differences and then investigate the Pol-InSAR performance of two proposed spaceborne SAR systems (ALOS/PalSAR and TerraSAR-L) operating in repeat-pass mode. For this, we introduce the novel concept of a phase tube which enables (1) a quantitative assessment of the Pol-InSAR performance, (2) a comparison between different sensor configurations, and (3) an optimization of the instrument settings for different Pol-InSAR applications. The phase tube may hence serve as an interface between system engineers and application-oriented scientists. The performance analysis reveals major limitations for even moderate levels of temporal decorrelation. Such deteriorations may be avoided in single-pass sensor configurations and we demonstrate the potential benefits from the use of future bi- and multistatic SAR interferometers.

  12. Federated query services provided by the Seamless SAR Archive project

    Science.gov (United States)

    Baker, S.; Bryson, G.; Buechler, B.; Meertens, C. M.; Crosby, C. J.; Fielding, E. J.; Nicoll, J.; Youn, C.; Baru, C.

    2013-12-01

    The NASA Advancing Collaborative Connections for Earth System Science (ACCESS) seamless synthetic aperture radar (SAR) archive (SSARA) project is a 2-year collaboration between UNAVCO, the Alaska Satellite Facility (ASF), the Jet Propulsion Laboratory (JPL), and OpenTopography at the San Diego Supercomputer Center (SDSC) to design and implement a seamless distributed access system for SAR data and derived data products (i.e. interferograms). A major milestone for the first year of the SSARA project was a unified application programming interface (API) for SAR data search and results at ASF and UNAVCO (WInSAR and EarthScope data archives) through the use of simple web services. A federated query service was developed using the unified APIs, providing users a single search interface for both archives (http://www.unavco.org/ws/brokered/ssara/sar/search). A command line client that utilizes this new service is provided as an open source utility for the community on GitHub (https://github.com/bakerunavco/SSARA). Further API development and enhancements added more InSAR specific keywords and quality control parameters (Doppler centroid, faraday rotation, InSAR stack size, and perpendicular baselines). To facilitate InSAR processing, the federated query service incorporated URLs for DEM (from OpenTopography) and tropospheric corrections (from the JPL OSCAR service) in addition to the URLs for SAR data. This federated query service will provide relevant QC metadata for selecting pairs of SAR data for InSAR processing and all the URLs necessary for interferogram generation. Interest from the international community has prompted an effort to incorporate other SAR data archives (the ESA Virtual Archive 4 and the DLR TerraSAR-X_SSC Geohazard Supersites and Natural Laboratories collections) into the federated query service which provide data for researchers outside the US and North America.

  13. Absorption heat pumps

    Science.gov (United States)

    Huhtinen, M.; Heikkilae, M.; Andersson, R.

    1987-03-01

    The aim of the study was to analyze the technical and economic feasibility of absorption heat pumps in Finland. The work was done as a case study: the technical and economic analyses have been carried out for six different cases, where in each the suitable size and type of the heat pump plant and the auxiliary components and connections were specified. The study also detailed the costs concerning the procurement, installation and test runs of the machinery, as well as the savings in energy costs incurred by the introduction of the plant. Conclusions were drawn of the economic viability of the applications studied. The following cases were analyzed: heat recovery from flue gases and productin of district heat in plants using peat, natural gas, and municipal wastes as a fuel. Heat recovery in the pulp and paper industry for the upgrading of pressure of secondary steam and for the heating of white liquor and combustion and drying the air. Heat recovery in a peat-fulled heat and power plant from flue gases that have been used for the drying of peat. According to the study, the absorption heat pump suits best to the production of district heat, when the heat source is the primary energy is steam produced by the boiler. Included in the flue as condensing is the purification of flue gases. Accordingly, benefit is gained on two levels in thick applications. In heat and power plants the use of absorption heat pumps is less economical, due to the fact that the steam used by the pump reduces the production of electricity, which is rated clearly higher than heat.

  14. Very slow lava extrusion continued for more than five years after the 2011 Shinmoedake eruption observed from SAR interferometry

    Science.gov (United States)

    Ozawa, T.; Miyagi, Y.

    2017-12-01

    Shinmoe-dake located to SW Japan erupted in January 2011 and lava accumulated in the crater (e.g., Ozawa and Kozono, EPS, 2013). Last Vulcanian eruption occurred in September 2011, and after that, no eruption has occurred until now. Miyagi et al. (GRL, 2014) analyzed TerraSAR-X and Radarsat-2 SAR data acquired after the last eruption and found continuous inflation in the crater. Its inflation decayed with time, but had not terminated in May 2013. Since the time-series of inflation volume change rate fitted well to the exponential function with the constant term, we suggested that lava extrusion had continued in long-term due to deflation of shallow magma source and to magma supply from deeper source. To investigate its deformation after that, we applied InSAR to Sentinel-1 and ALOS-2 SAR data. Inflation decayed further, and almost terminated in the end of 2016. It means that this deformation has continued more than five years from the last eruption. We have found that the time series of inflation volume change rate fits better to the double-exponential function than single-exponential function with the constant term. The exponential component with the short time constant has almost settled in one year from the last eruption. Although InSAR result from TerraSAR-X data of November 2011 and May 2013 indicated deflation of shallow source under the crater, such deformation has not been obtained from recent SAR data. It suggests that this component has been due to deflation of shallow magma source with excess pressure. In this study, we found the possibility that long-term component also decayed exponentially. Then this factor may be deflation of deep source or delayed vesiculation.

  15. Spatiotemporal Characterization of Land Subsidence and Uplift (2009–2010 over Wuhan in Central China Revealed by TerraSAR-X InSAR Analysis

    Directory of Open Access Journals (Sweden)

    Lin Bai

    2016-04-01

    Full Text Available The effects of ground deformation pose a significant geo-hazard to the environment and infrastructure in Wuhan, the most populous city in Central China, in the eastern Jianghan Plain at the intersection of the Yangtze and Han rivers. Prior to this study, however, rates and patterns of region-wide ground deformation in Wuhan were little known. Here we employ multi-temporal SAR interferometry to detect and characterize spatiotemporal variations of ground deformation in major metropolitan areas in Wuhan. A total of twelve TerraSAR-X images acquired during 2009–2010 are used in the InSAR time series analysis. InSAR-derived results are validated by levelling survey measurements and reveal a distinct subsidence pattern within six zones in major commercial and industrial areas, with a maximum subsidence rate up to −67.3 mm/year. A comparison analysis between subsiding patterns and urban developments as well as geological conditions suggests that land subsidence in Wuhan is mainly attributed to anthropogenic activities, natural compaction of soft soil, and karst dissolution of subsurface carbonate rocks. However, anthropogenic activities related to intensive municipal construction and industrial production have more significant impacts on the measured subsidence than natural factors. Moreover, remarkable signals of secular land uplift are found along both banks of the Yangtze River, especially along the southern bank, with deformation rates ranging mostly from +5 mm/year to +17.5 mm/year. A strong temporal correlation is highlighted between the detected displacement evolutions and the water level records of the Yangtze River, inferring that this previously unknown deformation phenomenon is likely related to seasonal fluctuations in water levels of the Yangtze River.

  16. Digital demodulator for wide bandwidth SAR

    DEFF Research Database (Denmark)

    Jørgensen, Jørn Hjelm

    2000-01-01

    A novel approach to the design of efficient digital quadrature demodulators for wide bandwidth SAR systems is described. Efficiency is obtained by setting the intermediate frequency to 1/4 the ADC sampling frequency. One channel is made filter-free by synchronizing the local oscillator with the o......A novel approach to the design of efficient digital quadrature demodulators for wide bandwidth SAR systems is described. Efficiency is obtained by setting the intermediate frequency to 1/4 the ADC sampling frequency. One channel is made filter-free by synchronizing the local oscillator...... with the output decimator. The filter required by the other channel is optimized through global search using the system level performance metrics integrated sidelobe level ratio (ISLR) and peak sidelobe level ratio (PSLR)....

  17. SAR Target Recognition via Supervised Discriminative Dictionary Learning and Sparse Representation of the SAR-HOG Feature

    Directory of Open Access Journals (Sweden)

    Shengli Song

    2016-08-01

    Full Text Available Automatic target recognition (ATR in synthetic aperture radar (SAR images plays an important role in both national defense and civil applications. Although many methods have been proposed, SAR ATR is still very challenging due to the complex application environment. Feature extraction and classification are key points in SAR ATR. In this paper, we first design a novel feature, which is a histogram of oriented gradients (HOG-like feature for SAR ATR (called SAR-HOG. Then, we propose a supervised discriminative dictionary learning (SDDL method to learn a discriminative dictionary for SAR ATR and propose a strategy to simplify the optimization problem. Finally, we propose a SAR ATR classifier based on SDDL and sparse representation (called SDDLSR, in which both the reconstruction error and the classification error are considered. Extensive experiments are performed on the MSTAR database under standard operating conditions and extended operating conditions. The experimental results show that SAR-HOG can reliably capture the structures of targets in SAR images, and SDDL can further capture subtle differences among the different classes. By virtue of the SAR-HOG feature and SDDLSR, the proposed method achieves the state-of-the-art performance on MSTAR database. Especially for the extended operating conditions (EOC scenario “Training 17 ∘ —Testing 45 ∘ ”, the proposed method improves remarkably with respect to the previous works.

  18. Individual Building Extraction from TerraSAR-X Images Based on Ontological Semantic Analysis

    Directory of Open Access Journals (Sweden)

    Rong Gui

    2016-08-01

    Full Text Available Accurate building information plays a crucial role for urban planning, human settlements and environmental management. Synthetic aperture radar (SAR images, which deliver images with metric resolution, allow for analyzing and extracting detailed information on urban areas. In this paper, we consider the problem of extracting individual buildings from SAR images based on domain ontology. By analyzing a building scattering model with different orientations and structures, the building ontology model is set up to express multiple characteristics of individual buildings. Under this semantic expression framework, an object-based SAR image segmentation method is adopted to provide homogeneous image objects, and three categories of image object features are extracted. Semantic rules are implemented by organizing image object features, and the individual building objects expression based on an ontological semantic description is formed. Finally, the building primitives are used to detect buildings among the available image objects. Experiments on TerraSAR-X images of Foshan city, China, with a spatial resolution of 1.25 m × 1.25 m, have shown the total extraction rates are above 84%. The results indicate the ontological semantic method can exactly extract flat-roof and gable-roof buildings larger than 250 pixels with different orientations.

  19. A Novel Variable Index and Excision CFAR Based Ship Detection Method on SAR Imagery

    Directory of Open Access Journals (Sweden)

    Kefeng Ji

    2015-01-01

    Full Text Available When applying the constant false alarm rate (CFAR detector to ship detection on synthetic aperture radar (SAR imagery, multiple interferers such as upwelling, breaking waves, ambiguities, and neighboring ships in a dense traffic area will degrade the probability of detection. In this paper, we propose a novel variable index and excision CFAR (VIE-CFAR based ship detection method to alleviate the masking effect of multiple interferers. Firstly, we improve the variable index (VI CFAR with an excision procedure, which censors the multiple interferers from the reference cells. And then, the paper integrates the novel CFAR concept into a ship detection scheme on SAR imagery, which adopts the VIE-CFAR to screen reference cells and the distribution to derive detection threshold. Finally, we analyze the performances of the VIE-CFAR under different environments and validate the proposed method on both ENVISAT and TerraSAR-X SAR data. The results demonstrate that the proposed method outperforms other existing detectors, especially in the presence of multiple interferers.

  20. The dual-use potential of the TerraSAR-X mission

    Science.gov (United States)

    Suess, Helmut; Buckreuss, Stefan

    2009-05-01

    TerraSAR-X, Germany's first national remote sensing satellite, is implemented in a public-private partnership between the German Aerospace Centre (DLR) and EADS Astrium, Infoterra GmbH. This radar satellite, launched at June 15th 2007 supplies high-quality radar data for purposes of scientific observation of the Earth for a period of at least five years. The first part of the paper describes the key features of the TerraSAR-X mission, the high-resolution X-Band Synthetic Aperture Radar which allows the operation in Spotlight, Stripmap and ScanSAR mode with various polarizations. The second part of this paper deals with the interpretation of TerraSAR-X images under dual-use aspects, especially for security and reconnaissance purposes. Examples for relevant and characteristic target categories are listed and attributes for a precise description are defined. As a measure for resolution and interpretation the public NIIRS-table (National Image Interpretation Rating Scale) is used. As an application example the characteristic scenario of a military airport including railway and route connections are extracted. Finally the applicability of the NIIRS-table is discussed in this particular case.

  1. Dynamic Deformation of ETNA Volcano Observed by GPS and SAR Interferometry

    Science.gov (United States)

    Lundgren, P.; Rosen, P.; Webb, F.; Tesauro, M.; Lanari, R.; Sansosi, E.; Puglisi, G.; Bonforte, A.; Coltelli, M.

    1999-01-01

    Synthetic aperture radar (SAR) interferometry and GPS have shown that during the quiescent period from 1993-1995 Mt. Etna volcano, Italy, inflated. Since the initiation of eruptive activity since late 1995 the deformation has been more contentious. We will explore the detailed deformation during the period from 1995-1996 spanning the late stages of inflation and the beginning of eruptive activity. We use SAR interferometry and GPS data to measure the volcano deformation. We invert the observed deformation for both simple point source. le crack elastic sources or if warranted for a spheroidal pressure So In particular, we will examine the evolution of the inflation and the transition to a lesser deflation observed at the end of 1995. We use ERS-1/2 SAR data from both ascending and descending passes to allow for dense temporal 'sampling of the deformation and to allow us to critically assess atmospheric noise. Preliminary results from interferometry suggest that the inflation rate accelerated prior to resumption of activity in 1995, while GPS data suggest a more steady inflation with some fluctuation following the start of activity. This study will compare and contrast the interferometric SAR and GPS results and will address the strengths and weaknesses of each technique towards volcano deformation studies.

  2. Feature-Based Nonlocal Polarimetric SAR Filtering

    Directory of Open Access Journals (Sweden)

    Xiaoli Xing

    2017-10-01

    Full Text Available Polarimetric synthetic aperture radar (PolSAR images are inherently contaminated by multiplicative speckle noise, which complicates the image interpretation and image analyses. To reduce the speckle effect, several adaptive speckle filters have been developed based on the weighted average of the similarity measures commonly depending on the model or probability distribution, which are often affected by the distribution parameters and modeling texture components. In this paper, a novel filtering method introduces the coefficient of variance ( CV and Pauli basis (PB to measure the similarity, and the two features are combined with the framework of the nonlocal mean filtering. The CV is used to describe the complexity of various scenes and distinguish the scene heterogeneity; moreover, the Pauli basis is able to express the polarimetric information in PolSAR image processing. This proposed filtering combines the CV and Pauli basis to improve the estimation accuracy of the similarity weights. Then, the similarity of the features is deduced according to the test statistic. Subsequently, the filtering is proceeded by using the nonlocal weighted estimation. The performance of the proposed filter is tested with the simulated images and real PolSAR images, which are acquired by AIRSAR system and ESAR system. The qualitative and quantitative experiments indicate the validity of the proposed method by comparing with the widely-used despeckling methods.

  3. Tracking morphological changes and slope instability using spaceborne and ground-based SAR data

    Science.gov (United States)

    Di Traglia, Federico; Nolesini, Teresa; Ciampalini, Andrea; Solari, Lorenzo; Frodella, William; Bellotti, Fernando; Fumagalli, Alfio; De Rosa, Giuseppe; Casagli, Nicola

    2018-01-01

    Stromboli (Aeolian Archipelago, Italy) is an active volcano that is frequently affected by moderate to large mass wasting, which has occasionally triggered tsunamis. With the aim of understanding the relationship between the geomorphologic evolution and slope instability of Stromboli, remote sensing information from space-born Synthetic Aperture Radar (SAR) change detection and interferometry (InSAR) () and Ground Based InSAR (GBInSAR) was compared with field observations and morphological analyses. Ground reflectivity and SqueeSAR™ (an InSAR algorithm for surface deformation monitoring) displacement measurements from X-band COSMO-SkyMed satellites (CSK) were analysed together with displacement measurements from a permanent-sited, Ku-band GBInSAR system. Remote sensing results were compared with a preliminary morphological analysis of the Sciara del Fuoco (SdF) steep volcanic flank, which was carried out using a high-resolution Digital Elevation Model (DEM). Finally, field observations, supported by infrared thermographic surveys (IRT), allowed the interpretation and validation of remote sensing data. The analysis of the entire dataset (collected between January 2010 and December 2014) covers a period characterized by a low intensity of Strombolian activity. This period was punctuated by the occurrence of lava overflows, occurring from the crater terrace evolving downslope toward SdF, and flank eruptions, such as the 2014 event. The amplitude of the CSK images collected between February 22nd, 2010, and December 18th, 2014, highlights that during periods characterized by low-intensity Strombolian activity, the production of materials ejected from the crater terrace towards the SdF is generally low, and erosion is the prevailing process mainly affecting the central sector of the SdF. CSK-SqueeSAR™ and GBInSAR data allowed the identification of low displacements in the SdF, except for high displacement rates (up to 1.5 mm/h) that were measured following both lava

  4. Experiment of Azimuth-invariant Bistatic UHF UWB SAR

    Science.gov (United States)

    Xie, Hongtu; Shi, Shaoying; Mao, Junfa; Li, Fuhai; An, Daoxiang; Zhou, Zhimin; Wang, Guoqian

    2018-01-01

    Bistatic ultrahigh frequency ultrawideband synthetic aperture radar (UHF UWB SAR) has the well ability of the penetrating the foliage, high-resolution imaging and providing the increased information. In the paper, an imaging experiment of the azimuth-invariant bistatic UHF UWB SAR is described and the result is proposed. In August 2015, an along-track bistatic UHF UWB SAR experiment was conducted in China, and the raw data was collected. In this bistatic SAR system, the transmitter and receiver are both carried by a vehicle and separated by an invariable distance. The aim was to investigate the imaging property of the bistatic UHF UWB SAR system. Bistatic image was obtained using the subaperture spectrum-equilibrium method integrated with the fast factorized back projection algorithm (FFBPA). Experiment results prove the validity of the bistatic UHF UWB SAR experiment.

  5. Polarimetric SAR image classification based on discriminative dictionary learning model

    Science.gov (United States)

    Sang, Cheng Wei; Sun, Hong

    2018-03-01

    Polarimetric SAR (PolSAR) image classification is one of the important applications of PolSAR remote sensing. It is a difficult high-dimension nonlinear mapping problem, the sparse representations based on learning overcomplete dictionary have shown great potential to solve such problem. The overcomplete dictionary plays an important role in PolSAR image classification, however for PolSAR image complex scenes, features shared by different classes will weaken the discrimination of learned dictionary, so as to degrade classification performance. In this paper, we propose a novel overcomplete dictionary learning model to enhance the discrimination of dictionary. The learned overcomplete dictionary by the proposed model is more discriminative and very suitable for PolSAR classification.

  6. Ocean Surface Wind Speed of Hurricane Helene Observed by SAR

    DEFF Research Database (Denmark)

    Xu, Qing; Cheng, Yongcun; Li, Xiaofeng

    2011-01-01

    The hurricanes can be detected by many remote sensors, but synthetic aperture radar (SAR) can yield high-resolution (sub-kilometer) and low-level wind information that cannot be seen below the cloud by other sensors. In this paper, an assessment of SAR capability of monitoring high......-resolution hurricane was conducted. A case study was carried out to retrieve ocean surface wind field from C-band RADARSAT-1 SAR image which captured the structure of hurricane Helene over the Atlantic Ocean on 20 September, 2006. With wind direction from the outputs of U.S. Navy Operational Global Atmospheric...... CIWRAP models have been tested to extract wind speed from SAR data. The SAR retrieved ocean surface winds were compared to the aircraft wind speed observations from stepped frequency microwave radiometer (SFMR). The results show the capability of hurricane wind monitoring by SAR....

  7. Persistent Scatterer InSAR monitoring of Bratislava urban area

    Science.gov (United States)

    Bakon, Matus; Perissin, Daniele; Papco, Juraj; Lazecky, Milan

    2014-05-01

    ) technique, covering the target area with 57 Envisat ASAR images from Ascending Track No. 229 (32) and Descending Track No. 265 (25) captured between years 2002 and 2010. Processing involves Sarproz (Copyright (c) 2009 Daniele Perissin) a powerful software solution for obtaining differential interferograms and performing PSInSAR methodology. The area of interest to investigate the deformation phenomena is covering approximately 16 by 16 kilometers (256 sqkm). For evaluation of PSInSAR potential to detect and monitor ground displacements, PS derived time series of deformation signal were compared to the field GNSS data from three GNSS stations coded PIL1, BRAT and GKU4. By the detailed look on the deformation maps the investigated urban area of Bratislava is relatively stable with the deformation rates within the few (±5) millimeters. The comparison of PSInSAR derived time series with GNSS data indicates good correlation and confirms achievable precision and applicability of InSAR measurements for ground stability monitoring purposes. Data for this work were provided by European Space Agency within the Category-1 project ID 9981: "Detection of ground deformation using radar interferometry techniques". The authors are grateful to the Tatrabanka Foundation and The National Scholarship Programme of the Slovak Republic for the opportunity to work together. Data have been processed by the Sarproz (Copyright (c) 2009 Daniele Perissin) and visualised in Google Earth. This paper is also the result of the implementation of the project: the National Centre of Earth's Surface Deformation Diagnostic in the area of Slovakia, ITMS 26220220108 supported by the Research and Development Operational Programme funded by the ERDF and the grant No. 1/0642/13 of the Slovak Grant Agency VEGA.

  8. Subsidence Detected by Multi-Pass Differential SAR Interferometry in the Cassino Plain (Central Italy: Joint Effect of Geological and Anthropogenic Factors?

    Directory of Open Access Journals (Sweden)

    Marco Polcari

    2014-10-01

    Full Text Available In the present work, the Differential SAR Interferometry (DInSAR technique has been applied to study the surface movements affecting the sedimentary basin of Cassino municipality. Two datasets of SAR images, provided by ERS 1-2 and Envisat missions, have been acquired from 1992 to 2010. Such datasets have been processed independently each other and with different techniques nevertheless providing compatible results. DInSAR data show a subsidence rate mostly located in the northeast side of the city, with a subsidence rate decreasing from about 5–6 mm/yr in the period 1992–2000 to about 1–2 mm/yr between 2004 and 2010, highlighting a progressive reduction of the phenomenon. Based on interferometric results and geological/geotechnical observations, the explanation of the detected movements allows to confirm the anthropogenic (surface effect due to building construction and geological causes (thickness and characteristics of the compressible stratum.

  9. Ionospheric Correction in Using ALOS PALSAR InSAR Data for Monitoring Permafrost Subsidence associated with an Arctic Tundra Fire

    Science.gov (United States)

    Liao, H.; Meyer, F. J.; Liu, L.

    2017-12-01

    deformation estimates. We will also show that ionospheric correction increases the number of usable InSAR data, which improves the accuracy in the retrieved permafrost variables such as subsidence rates and active layer thickness and allows for the detection of shorter-term variations in elevation changes over permafrost areas.

  10. Nutrition and magnesium absorption

    OpenAIRE

    Brink, E.J.

    1992-01-01

    The influence of various nutrients present in dairy products and soybean-based products on absorption of magnesium has been investigated. The studies demonstrate that soybean protein versus casein lowers apparent magnesium absorption in rats through its phytate component. However, true magnesium absorption was neither affected by soybean protein in the diet nor by supplemental phytate. The inhibitory influence of soybean protein and phytate on apparent magnesium absorption was found ...

  11. Discovery of unsymmetrical aromatic disulfides as novel inhibitors of SARS-CoV main protease: Chemical synthesis, biological evaluation, molecular docking and 3D-QSAR study.

    Science.gov (United States)

    Wang, Li; Bao, Bo-Bo; Song, Guo-Qing; Chen, Cheng; Zhang, Xu-Meng; Lu, Wei; Wang, Zefang; Cai, Yan; Li, Shuang; Fu, Sheng; Song, Fu-Hang; Yang, Haitao; Wang, Jian-Guo

    2017-09-08

    The worldwide outbreak of severe acute respiratory syndrome (SARS) in 2003 had caused a high rate of mortality. Main protease (M pro ) of SARS-associated coronavirus (SARS-CoV) is an important target to discover pharmaceutical compounds for the therapy of this life-threatening disease. During the course of screening new anti-SARS agents, we have identified that a series of unsymmetrical aromatic disulfides inhibited SARS-CoV M pro significantly for the first time. Herein, 40 novel unsymmetrical aromatic disulfides were synthesized chemically and their biological activities were evaluated in vitro against SARS-CoV M pro . These novel compounds displayed excellent IC 50 data in the range of 0.516-5.954 μM. Preliminary studies indicated that these disulfides are reversible and mpetitive inhibitors. A possible binding mode was generated via molecular docking simulation and a comparative field analysis (CoMFA) model was constructed to understand the structure-activity relationships. The present research therefore has provided some meaningful guidance to design and identify anti-SARS drugs with totally new chemical structures. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  12. Modeling the intracellular pathogen-immune interaction with cure rate

    Science.gov (United States)

    Dubey, Balram; Dubey, Preeti; Dubey, Uma S.

    2016-09-01

    Many common and emergent infectious diseases like Influenza, SARS, Hepatitis, Ebola etc. are caused by viral pathogens. These infections can be controlled or prevented by understanding the dynamics of pathogen-immune interaction in vivo. In this paper, interaction of pathogens with uninfected and infected cells in presence or absence of immune response are considered in four different cases. In the first case, the model considers the saturated nonlinear infection rate and linear cure rate without absorption of pathogens into uninfected cells and without immune response. The next model considers the effect of absorption of pathogens into uninfected cells while all other terms are same as in the first case. The third model incorporates innate immune response, humoral immune response and Cytotoxic T lymphocytes (CTL) mediated immune response with cure rate and without absorption of pathogens into uninfected cells. The last model is an extension of the third model in which the effect of absorption of pathogens into uninfected cells has been considered. Positivity and boundedness of solutions are established to ensure the well-posedness of the problem. It has been found that all the four models have two equilibria, namely, pathogen-free equilibrium point and pathogen-present equilibrium point. In each case, stability analysis of each equilibrium point is investigated. Pathogen-free equilibrium is globally asymptotically stable when basic reproduction number is less or equal to unity. This implies that control or prevention of infection is independent of initial concentration of uninfected cells, infected cells, pathogens and immune responses in the body. The proposed models show that introduction of immune response and cure rate strongly affects the stability behavior of the system. Further, on computing basic reproduction number, it has been found to be minimum for the fourth model vis-a-vis other models. The analytical findings of each model have been exemplified by

  13. Fast Detection of Oil Spills and Ships Using SAR Images

    Directory of Open Access Journals (Sweden)

    Alberto Lupidi

    2017-03-01

    Full Text Available In this paper, we show the capabilities of a new maritime control system based on the processing of COSMO-SkyMed Synthetic Aperture Radar (SAR images. This system aims at fast detection of ships that may be responsible for illegal oil dumping. In particular, a novel detection algorithm based on the joint use of the significance parameter, wavelet correlator and a two-dimensional Constant False Alarm Rate (2D-CFAR is designed. Results show the effectiveness of such algorithms, which can be used by the maritime authorities to have a faster although still reliable response. The proposed algorithm, together with the short revisit time of the COSMO-SkyMed constellation, can help with tracking the scenario evolution from one acquisition to the next.

  14. Mesodynamics in the SARS nucleocapsid measured by NMR field cycling

    Energy Technology Data Exchange (ETDEWEB)

    Clarkson, Michael W.; Lei Ming; Eisenmesser, Elan Z.; Labeikovsky, Wladimir [MS009 Brandeis University, Department of Biochemistry and Howard Hughes Medical Institute (United States); Redfield, Alfred [MS009 Brandeis University, Department of Biochemistry (United States)], E-mail: redfield@brandeis.edu; Kern, Dorothee [MS009 Brandeis University, Department of Biochemistry and Howard Hughes Medical Institute (United States)], E-mail: dkern@brandeis.edu

    2009-09-15

    Protein motions on all timescales faster than molecular tumbling are encoded in the spectral density. The dissection of complex protein dynamics is typically performed using relaxation rates determined at high and ultra-high field. Here we expand this range of the spectral density to low fields through field cycling using the nucleocapsid protein of the SARS coronavirus as a model system. The field-cycling approach enables site-specific measurements of R{sub 1} at low fields with the sensitivity and resolution of a high-field magnet. These data, together with high-field relaxation and heteronuclear NOE, provide evidence for correlated rigid-body motions of the entire {beta}-hairpin, and corresponding motions of adjacent loops with a time constant of 0.8 ns (mesodynamics). MD simulations substantiate these findings and provide direct verification of the time scale and collective nature of these motions.

  15. Absorption and excretion tests

    International Nuclear Information System (INIS)

    Berberich, R.

    1988-01-01

    The absorption and excretion of radiopharmaceuticals is still of interest in diagnostic investigations of nuclear medicine. In this paper the most common methods of measuring absorption and excretion are described. The performance of the different tests and their standard values are discussed. More over the basic possibilities of measuring absorption and excretion including the needed measurement equipments are presented. (orig.) [de

  16. SAR Subsets for Selected Field Sites, 2007-2010

    Data.gov (United States)

    National Aeronautics and Space Administration — ABSTRACT: This data set provides Synthetic Aperture Radar (SAR) images for 42 selected sites from various terrestrial ecology and meteorological monitoring networks...

  17. SAR Subsets for Selected Field Sites, 2007-2010

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set provides Synthetic Aperture Radar (SAR) images for 42 selected sites from various terrestrial ecology and meteorological monitoring networks including...

  18. Bistatic SAR: State of the Art and Development Trend

    Directory of Open Access Journals (Sweden)

    Zeng Tao

    2012-12-01

    Full Text Available Bistatic SAR (BiSAR systems have attracted the interests from global researchers and become a hotspot in the international radar community due to the progress of radar technology and rapidly increased applications nowadays. Based on the BiSAR experiments and breakthrough of the key technology, the paper summarized the general progresses of BiSAR systems, especially in European radar community, from different aspects such as system design, processing idea and topology etc. Different bistatic image formation algorithms have been analyzed and reviewed. Finally, the development trend is discussed in the paper.

  19. Evaluation of the Wishart test statistics for polarimetric SAR data

    DEFF Research Database (Denmark)

    Skriver, Henning; Nielsen, Allan Aasbjerg; Conradsen, Knut

    2003-01-01

    A test statistic for equality of two covariance matrices following the complex Wishart distribution has previously been used in new algorithms for change detection, edge detection and segmentation in polarimetric SAR images. Previously, the results for change detection and edge detection have been...... quantitatively evaluated. This paper deals with the evaluation of segmentation. A segmentation performance measure originally developed for single-channel SAR images has been extended to polarimetric SAR images, and used to evaluate segmentation for a merge-using-moment algorithm for polarimetric SAR data....

  20. Cloud storage and computing resources for the UNAVCO SAR Archive

    Science.gov (United States)

    Baker, S.; Crosby, C. J.; Meertens, C. M.

    2016-12-01

    UNAVCO is a non-profit university-governed consortium that operates the National Science Foundation (NSF) Geodesy Advancing Geosciences and EarthScope (GAGE) facility and provides operational support to the Western North America InSAR Consortium (WInSAR). The synthetic aperture radar (SAR) archive at UNAVCO currently provides access to over 70TB of unprocessed data for community geoscience research. Historically, users have downloaded data and performed InSAR processing on local machines. However, given the increasing volumes of SAR data available and the size of an individual scene, this model may be inefficient. As cloud computing has become more mainstream, UNAVCO has begun developing capabilities to provide data and processing resources in the same location. The test environment is using the Texas Advanced Computing Center (TACC), part of the NSF Extreme Science and Engineering Discovery Environment (XSEDE). The entire UNAVCO SAR archive is available at TACC along with virtual machines preconfigured with InSAR processing software. Users will be able to quickly access and process SAR data, providing a scalable computing environment for more efficient and larger scale analyzes by the UNAVCO WInSAR community.

  1. Hydrodynamics of the groundwater-fed Sian Ka'an Wetlands, Mexico, From InSAR and SAR Data

    DEFF Research Database (Denmark)

    Gondwe, Bibi Ruth Neuman; Hong, S.; Wdowinski, S.

    2008-01-01

    of no hurricanes, maximum extent of flooding occurs in November-December, 1-2 months after the end of the rainy season (2640 to 2980 km2). The smallest degree of flooding occurs in May (1350 km2) at the end of the dry season. This information along with relative water level change maps may be used for improved...... to understand, quantify and predict the wetland dynamics. Remotely sensed Interferometric Synthetic Aperture Radar (InSAR) and Synthetic Aperture Radar (SAR) data offer new opportunities to get hydrodynamic information, which is useful for wetland management. InSAR data produces temporal phase......-changes of the backscattered radar signal, which can be related to the water level changes in vegetated wetlands. SAR data reveals information of surface properties such as the degree of flooding through the amplitude of the backscattered signal. We used RADARSAT-1 InSAR and SAR data to form 36 interferograms and 13 flooding...

  2. Retrieval of ice thickness from polarimetric SAR data

    Science.gov (United States)

    Kwok, R.; Yueh, S. H.; Nghiem, S. V.; Huynh, D. D.

    1993-01-01

    We describe a potential procedure for retrieving ice thickness from multi-frequency polarimetric SAR data for thin ice. This procedure includes first masking out the thicker ice types with a simple classifier and then deriving the thickness of the remaining pixels using a model-inversion technique. The technique used to derive ice thickness from polarimetric observations is provided by a numerical estimator or neural network. A three-layer perceptron implemented with the backpropagation algorithm is used in this investigation with several improved aspects for a faster convergence rate and a better accuracy of the neural network. These improvements include weight initialization, normalization of the output range, the selection of offset constant, and a heuristic learning algorithm. The performance of the neural network is demonstrated by using training data generated by a theoretical scattering model for sea ice matched to the database of interest. The training data are comprised of the polarimetric backscattering coefficients of thin ice and the corresponding input ice parameters to the scattering model. The retrieved ice thickness from the theoretical backscattering coefficients is compare with the input ice thickness to the scattering model to illustrate the accuracy of the inversion method. Results indicate that the network convergence rate and accuracy are higher when multi-frequency training sets are presented. In addition, the dominant backscattering coefficients in retrieving ice thickness are found by comparing the behavior of the network trained backscattering data at various incidence angels. After the neural network is trained with the theoretical backscattering data at various incidence anges, the interconnection weights between nodes are saved and applied to the experimental data to be investigated. In this paper, we illustrate the effectiveness of this technique using polarimetric SAR data collected by the JPL DC-8 radar over a sea ice scene.

  3. Large-scale time-series InSAR analysis of the Sacramento-San Joaquin delta subsidence using UAVSAR

    Science.gov (United States)

    Bekaert, D. P.; Jones, C. E.; An, K.; Huang, M. H.

    2016-12-01

    The Sacramento-San Joaquin delta (Delta) contains more than 1700 km of levees that protect various reclaimed lands from flooding. Most of the delta is experiencing subsidence at rates that can exceed 5 cm/yr locally, and which can affect the structural integrity of the levees. In-situ and airborne LIDAR monitoring of this extensive levee network is expensive, making Interferometric Synthetic Aperture Radar (InSAR) an attractive, cost-effective alternative that can provide uniform and consistent monitoring. InSAR has proven to be a powerful technique to study surface displacements at high accuracy (few mm/year), over large regions (up to 250 km wide swaths), and at a high spatial resolution (up to a meter). However widespread usage of InSAR, particularly within the application community, is challenged by several technical issues, the most significant of which are decorrelation noise introduced by a change of scattering properties (e.g., moisture and vegetation), and noise due to variation in atmospheric properties between different SAR acquisitions (i.e., tropospheric delay). These effects are particularly limiting in the rural/agricultural setting of the Delta. We demonstrate the usage of InSAR for spatially comprehensive subsidence monitoring both at the scale of the levees and at a scale that captures the intra-island variability. The study uses data collected over a period of six years (2009-2015) with NASA's Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR) instrument, which is the prototype airborne instrument for the NISAR mission. We mitigate atmospheric noise by estimating a correction from state-of-the-art weather models, and reduce decorrelation noise by utilizing L-band SAR and using advanced time-series InSAR processing methods. Our analysis includes nine UAVSAR flight lines that cover altogether an area of approximately 8500 km2, including the Delta and the surrounding areas.

  4. Espectro de gotas e idade de trifólios na taxa de absorção e efeito residual de fungicidas em soja Drops spectra and leaflets age on the fungicides absorption rate and residual effect in soybean

    Directory of Open Access Journals (Sweden)

    Giuvan Lenz

    2011-10-01

    Full Text Available O objetivo do presente trabalho foi avaliar o efeito de espectros de gotas (grossas, médias e finas na velocidade de absorção de fungicidas, para trifólios de diferentes idades através de medida indireta expressa pelo residual de controle de ferrugem asiática da soja (Phakopsora pachyrhizi. O delineamento experimental utilizado foi inteiramente casualizado, com quatro repetições, em arranjo fatorial (3x3x5x4, cujos fatores foram compostos por: três categorias de gotas (grossas, médias e finas; três diferentes posições de avaliação na planta (1°, 3° e 5° trifólios; quatro períodos de tempo entre a aplicação de fungicidas e aplicação de chuva simulada (0, 30, 60 e 120min, mais uma testemunha sem chuva; testemunha sem aplicação, mais os fungicidas azoxistrobina + ciproconazol (60+24g i.a. ha-1 + óleo mineral 0,6L ha-1, azoxistrobina (50g i.a. ha-1 + óleo mineral 0,6L ha-1 e ciproconazol (30g i.a. ha-1. Avaliou-se a densidade de gotas por centímetro quadrado, diâmetro mediano volumétrico, diâmetro mediano numérico e amplitude relativa, além do número de dias para o aparecimento da primeira pústula. Verificou-se que gotas de menor DMV proporcionam maior velocidade de absorção de fungicidas. Trifólios mais novos absorvem os fungicidas mais rapidamente. A utilização de azoxistrobina + ciproconazol + óleo mineral proporcionou o maior número de dias até o aparecimento da primeira pústula.This research aimed to evaluate the effect of large, medium and fine droplets spectra and its interaction with the fungicide absorption rate and leaflets age through indirect measurement expressed by the residual control of Asian soybean rust (Phakopsora pachyrhizi. The experimental design was completely randomized with four replications in a factorial scheme (3x3x5x4, which factors were composed of: three drops spectra (large, medium and fine; three different positions in the plant evaluated (1st, 3rd and 5th leaflets, four

  5. Analysis of summer subsidence in Barrow, Alaska, using InSAR and hyperspectral remote sensing

    OpenAIRE

    Mahmud Haghshenas Haghighi; M. Motagh; B. Heim; S. Chabrillat; D. Streletskiy; G. Grosse; T. Sachs; Katrin Kohnert

    2016-01-01

    In this study, gradual elevation change due to summer thawing of active layer in tundra permafrost landscape of Barrow, Alaska is investigated using SAR interferometry (InSAR) technique. We used a variety of SAR sensors including TerraSAR-X, ALOS, and Sentinel-1 images to assess elevation changes in summer season. Preliminary result, obtained by TerraSAR-X InSAR analysis, clearly delineates subsidence during the summer by identifying thousands of coherent pixels on ...

  6. Engaging students in geodesy: A quantitative InSAR module for undergraduate tectonics and geophysics classes

    Science.gov (United States)

    Taylor, H.; Charlevoix, D. J.; Pritchard, M. E.; Lohman, R. B.

    2013-12-01

    In the last several decades, advances in geodetic technology have allowed us to significantly expand our knowledge of processes acting on and beneath the Earth's surface. Many of these advances have come as a result of EarthScope, a community of scientists conducting multidisciplinary Earth science research utilizing freely accessible data from a variety of instruments. The geodetic component of EarthScope includes the acquisition of synthetic aperture radar (SAR) images, which are archived at the UNAVCO facility. Interferometric SAR complements the spatial and temporal coverage of GPS and allows monitoring of ground deformation in remote areas worldwide. However, because of the complex software required for processing, InSAR data are not readily accessible to most students. Even with these challenges, exposure at the undergraduate level is important for showing how geodesy can be applied in various areas of the geosciences and for promoting geodesy as a future career path. Here we present a module focused on exploring the tectonics of the western United States using InSAR data for use in undergraduate tectonics and geophysics classes. The module has two major objectives: address topics concerning tectonics in the western U.S. including Basin and Range extension, Yellowstone hotspot activity, and creep in southern California, and familiarize students with how imperfect real-world data can be manipulated and interpreted. Module questions promote critical thinking skills and data literacy by prompting students to use the information given to confront and question assumptions (e.g. 'Is there a consistency between seismic rates and permanent earthquake deformation? What other factors might need to be considered besides seismicity?'). The module consists of an introduction to the basics of InSAR and three student exercises, each focused on one of the topics listed above. Students analyze pre-processed InSAR data using MATLAB, or an Excel equivalent, and draw on GPS and

  7. Mechanisms of the electron density depletion in the SAR arc region

    Directory of Open Access Journals (Sweden)

    A. V. Pavlov

    Full Text Available This study compares the measurements of electron density and temperature and the integral airglow intensity at 630 nm in the SAR arc region and slightly south of this (obtained by the Isis 2 spacecraft during the 18 December 1971 magnetic storm, with the model results obtained using the time dependent one-dimensional mathematical model of the Earth's ionosphere and plasmasphere. The explicit expression in the third Enskog approximation for the electron thermal conductivity coefficient in the multicomponent mixture of ionized gases and a simplified calculation method for this coefficient presents an opportunity to calculate more exactly the electron temperature and density and 630 nm emission within SAR arc region are used in the model. Collisions between N2 and hot thermal electrons in the SAR arc region produce vibrationally excited nitrogen molecules. It appears that the loss rate of O+(4S due to reactions with the vibrationally excited nitrogen is enough to explain electron density depression by a factor of two at F-region heights and the topside ionosphere density variations within the SAR arc if the erosion of plasma within geomagnetic field tubes, during the main phase of the geomagnetic storm and subsequent filling of geomagnetic tubes during the recovery phase, are considered. To explain the disagreement by a factor 1.5 between the observed and modeled SAR arc electron densities an additional plasma drift velocity ~–30 m s–1 in the ion continuity equations is needed during the recovery phase. This additional plasma drift velocity is likely caused by the transition from convecting to corotating flux tubes on the equatorward wall of the trough. The electron densities and temperatures and 630 nm integral intensity at the SAR arc and slightly south of this region as measured for the 18 December 1971 magnetic storm were correctly described by the model without perpendicular electric fields

  8. Chandrayaan-2 dual-frequency SAR: Further investigation into lunar water and regolith

    Science.gov (United States)

    Putrevu, Deepak; Das, Anup; Vachhani, J. G.; Trivedi, Sanjay; Misra, Tapan

    2016-01-01

    The Space Applications Centre (SAC), one of the major centers of the Indian Space Research Organization (ISRO), is developing a high resolution, dual-frequency Synthetic Aperture Radar as a science payload on Chandrayaan-2, ISRO's second moon mission. With this instrument, ISRO aims to further the ongoing studies of the data from S-band MiniSAR onboard Chandrayaan-1 (India) and the MiniRF of Lunar Reconnaissance Orbiter (USA). The SAR instrument has been configured to operate with both L- and S-bands, sharing a common antenna. The S-band SAR will provide continuity to the MiniSAR data, whereas L-band is expected to provide deeper penetration of the lunar regolith. The system will have a selectable slant-range resolution from 2 m to 75 m, along with standalone (L or S) and simultaneous (L and S) modes of imaging. Various features of the instrument like hybrid and full-polarimetry, a wide range of imaging incidence angles (∼10° to ∼35°) and the high spatial resolution will greatly enhance our understanding of surface properties especially in the polar regions of the Moon. The system will also help in resolving some of the ambiguities in interpreting high values of Circular Polarization Ratio (CPR) observed in MiniSAR data. The added information from full-polarimetric data will allow greater confidence in the results derived particularly in detecting the presence (and estimating the quantity) of water-ice in the polar craters. Being a planetary mission, the L&S-band SAR for Chandrayaan-2 faced stringent limits on mass, power and data rate (15 kg, 100 W and 160 Mbps respectively), irrespective of any of the planned modes of operation. This necessitated large-scale miniaturization, extensive use of on-board processing, and devices and techniques to conserve power. This paper discusses the scientific objectives which drive the requirement of a lunar SAR mission and presents the configuration of the instrument, along with a description of a number of features of the

  9. MRI screening on bone ischemia of hip and knee in recovered SARS patients

    International Nuclear Information System (INIS)

    Cheng Xiaoguang; Qu Hui; Liu Wei; Sun Jing; Cheng Kebin; Feng Suchen; Li Xiaosong

    2004-01-01

    Objective: To screen ischemia in the hip and knee joints of recovered SARS patients with MRI, and to investigate the prevalence rate of bone ischemia in those patients and its relationship with the use of steroid. Methods: Hip and knee MRI examinations were performed in 76 recovered SARS patients. There were 17 males and 59 females. Eight patients were treated without steroid, while 68 patients with steroid. Dose and duration of steroid usage were available in 30 out of 68 patients. The MRI images were read by senior radiologists to determine whether bone ischemia and/or osteonecrosis was present. Appropriate statistic analysis was performed to determine the significance of difference between groups. Results: (1) The MRI appearance of osteonecrosis in femoral head and condyle and bone infarct in bone marrow found in SARS patients was identical to those caused by other conditions (including steroid usage in other diseases). (2) No one of 8 SARS without steroid developed osteonecrosis, while 25 out of 68 steroid users had osteonecrosis found by MRI screening, and the difference in prevalence of osteonecrosis between these 2 groups was significant. In 25 patients with osteonecrosis, 20 of them involved more than one joints. Osteonecrosis involved 32 femoral heads, 26 femoral condyles, and 6 in femoral and tibial shafts. Thirteen patients with osteonecrosis had greater total steroid dose, greater daily dose, and longer duration than those (17 patients) without osteonecrosis, however, the differences between the two groups were not statistically significant. Sixty-four patients out of 76 complained pain in joints, 50 of them had multiple joint pains. The pain was reported in hips in 40 cases, followed by knees in 36, low backs in 10, shoulders in 7, and wrists in 4, respectively. The differences in frequency of pain between steroid users and non-steroid users, as well as between osteonecrosis and non-osteonecrosis were not significant. Conclusion: MRI is recommended for

  10. Mechanisms of the electron density depletion in the SAR arc region

    Directory of Open Access Journals (Sweden)

    A. V. Pavlov

    1996-02-01

    Full Text Available This study compares the measurements of electron density and temperature and the integral airglow intensity at 630 nm in the SAR arc region and slightly south of this (obtained by the Isis 2 spacecraft during the 18 December 1971 magnetic storm, with the model results obtained using the time dependent one-dimensional mathematical model of the Earth\\'s ionosphere and plasmasphere. The explicit expression in the third Enskog approximation for the electron thermal conductivity coefficient in the multicomponent mixture of ionized gases and a simplified calculation method for this coefficient presents an opportunity to calculate more exactly the electron temperature and density and 630 nm emission within SAR arc region are used in the model. Collisions between N2 and hot thermal electrons in the SAR arc region produce vibrationally excited nitrogen molecules. It appears that the loss rate of O+(4S due to reactions with the vibrationally excited nitrogen is enough to explain electron density depression by a factor of two at F-region heights and the topside ionosphere density variations within the SAR arc if the erosion of plasma within geomagnetic field tubes, during the main phase of the geomagnetic storm and subsequent filling of geomagnetic tubes during the recovery phase, are considered. To explain the disagreement by a factor 1.5 between the observed and modeled SAR arc electron densities an additional plasma drift velocity ~–30 m s–1 in the ion continuity equations is needed during the recovery phase. This additional plasma drift velocity is likely caused by the transition from convecting to corotating flux tubes on the equatorward wall of the trough. The electron densities and temperatures and 630 nm integral intensity at the SAR arc and slightly south of this region as measured for the 18 December 1971 magnetic storm were correctly described by the model without perpendicular electric fields. Within this model framework the effect of the

  11. Extension of a Fast GLRT Algorithm to 5D SAR Tomography of Urban Areas

    Directory of Open Access Journals (Sweden)

    Alessandra Budillon

    2017-08-01

    Full Text Available This paper analyzes a method for Synthetic Aperture Radar (SAR Tomographic (TomoSAR imaging, allowing the detection of multiple scatterers that can exhibit time deformation and thermal dilation by using a CFAR (Constant False Alarm Rate approach. In the last decade, several methods for TomoSAR have been proposed. The objective of this paper is to present the results obtained on high resolution tomographic SAR data of urban areas, by using a statistical test for detecting multiple scatterers that takes into account phase variations due to possible deformations and/or thermal dilation. The test can be evaluated in terms of probability of detection (PD and probability of false alarm (PFA, and is based on an approximation of a Generalized Likelihood Ratio Test (GLRT, denoted as Fast-Sup-GLRT. It was already applied and validated by the authors in the 3D case, while here it is extended and experimented in the 5D case. Numerical experiments on simulated and on StripMap TerraSAR-X (TSX data have been carried out. The presented results show that the adopted method allows the detection of a large number of scatterers and the estimation of their position with a good accuracy, and that the consideration of the thermal dilation and surface deformation helps in recovering more single and double scatterers, with respect to the case in which these contributions are not taken into account. Moreover, the capability of method to provide reliable estimates of the deformations in urban structure suggests its use in structure stress monitoring.

  12. Crustal Deformation along San Andreas Fault System revealed by GPS and Sentinel-1 InSAR

    Science.gov (United States)

    Xu, X.; Sandwell, D. T.

    2017-12-01

    We present a crustal deformation velocity map along the San Andreas Fault System by combining measurements from Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) and Global Positioning System (GPS) velocity models (CGM V1). We assembled 5 tracks of descending Sentinel-1 InSAR data spanning 2014.11-2017.02, and produced 545 interferograms, each of which covers roughly 250km x 420km area ( 60 bursts). These interferograms are unwrapped using SNAPHU [Chen & Zebker, 2002], with the 2Npi unwrapping ambiguity corrected with a sparse recovery method. We used coherence-based small baseline subset (SBAS) method [Tong & Schmidt, 2016] together with atmospheric correction by common-point stacking [Tymofyeyeva and Fialko, 2015] to construct deformation time series [Xu et. al., 2017]. Then we project the horizontal GPS model and vertical GPS data into satellite line-of-sight directions separately. We first remove the horizontal GPS model from InSAR measurements and perform elevation-dependent atmospheric phase correction. Then we compute the discrepancy between the remaining InSAR measurements and vertical GPS data. We interpolate this discrepancy and remove it from the residual InSAR measurements. Finally, we restore the horizontal GPS model. Preliminary results show that fault creep over the San Jacinto fault, the Elsinore fault, and the San Andreas creeping section is clearly resolved. During the period of drought, the Central Valley of California was subsiding at a high rate (up to 40 cm/yr), while the city of San Jose is uplifting due to recharge, with a quaternary fault acting as a ground water barrier. These findings will be reported during the meeting.

  13. Calcium absorption and achlorhydria

    International Nuclear Information System (INIS)

    Recker, R.R.

    1985-01-01

    Defective absorption of calcium has been thought to exist in patients with achlorhydria. The author compared absorption of calcium in its carbonate form with that in a pH-adjusted citrate form in a group of 11 fasting patients with achlorhydria and in 9 fasting normal subjects. Fractional calcium absorption was measured by a modified double-isotope procedure with 0.25 g of calcium used as the carrier. Mean calcium absorption (+/- S.D.) in the patients with achlorhydria was 0.452 +/- 0.125 for citrate and 0.042 +/- 0.021 for carbonate (P less than 0.0001). Fractional calcium absorption in the normal subjects was 0.243 +/- 0.049 for citrate and 0.225 +/- 0.108 for carbonate (not significant). Absorption of calcium from carbonate in patients with achlorhydria was significantly lower than in the normal subjects and was lower than absorption from citrate in either group; absorption from citrate in those with achlorhydria was significantly higher than in the normal subjects, as well as higher than absorption from carbonate in either group. Administration of calcium carbonate as part of a normal breakfast resulted in completely normal absorption in the achlorhydric subjects. These results indicate that calcium absorption from carbonate is impaired in achlorhydria under fasting conditions. Since achlorhydria is common in older persons, calcium carbonate may not be the ideal dietary supplement

  14. Mutational dynamics of the SARS coronavirus in cell culture and human populations isolated in 2003

    Directory of Open Access Journals (Sweden)

    Ooi Eng

    2004-09-01

    Full Text Available Abstract Background The SARS coronavirus is the etiologic agent for the epidemic of the Severe Acute Respiratory Syndrome. The recent emergence of this new pathogen, the careful tracing of its transmission patterns, and the ability to propagate in culture allows the exploration of the mutational dynamics of the SARS-CoV in human populations. Methods We sequenced complete SARS-CoV genomes taken from primary human tissues (SIN3408, SIN3725V, SIN3765V, cultured isolates (SIN848, SIN846, SIN842, SIN845, SIN847, SIN849, SIN850, SIN852, SIN3408L, and five consecutive Vero cell passages (SIN2774_P1, SIN2774_P2, SIN2774_P3, SIN2774_P4, SIN2774_P5 arising from SIN2774 isolate. These represented individual patient samples, serial in vitro passages in cell culture, and paired human and cell culture isolates. Employing a refined mutation filtering scheme and constant mutation rate model, the mutation rates were estimated and the possible date of emergence was calculated. Phylogenetic analysis was used to uncover molecular relationships between the isolates. Results Close examination of whole genome sequence of 54 SARS-CoV isolates identified before 14th October 2003, including 22 from patients in Singapore, revealed the mutations engendered during human-to-Vero and Vero-to-human transmission as well as in multiple Vero cell passages in order to refine our analysis of human-to-human transmission. Though co-infection by different quasipecies in individual tissue samples is observed, the in vitro mutation rate of the SARS-CoV in Vero cell passage is negligible. The in vivo mutation rate, however, is consistent with estimates of other RNA viruses at approximately 5.7 × 10-6 nucleotide substitutions per site per day (0.17 mutations per genome per day, or two mutations per human passage (adjusted R-square = 0.4014. Using the immediate Hotel M contact isolates as roots, we observed that the SARS epidemic has generated four major genetic groups that are

  15. An anatomically realistic whole-body pregnant-woman model and specific absorption rates for pregnant-woman exposure to electromagnetic plane waves from 10 MHz to 2 GHz

    International Nuclear Information System (INIS)

    Nagaoka, Tomoaki; Togashi, Toshihiro; Saito, Kazuyuki; Takahashi, Masaharu; Ito, Koichi; Watanabe, Soichi

    2007-01-01

    The numerical dosimetry of pregnant women is an important issue in electromagnetic-field safety. However, an anatomically realistic whole-body pregnant-woman model for electromagnetic dosimetry has not been developed. Therefore, we have developed a high-resolution whole-body model of pregnant women. A new fetus model including inherent tissues of pregnant women was constructed on the basis of abdominal magnetic resonance imaging data of a 26-week-pregnant woman. The whole-body pregnant-woman model was developed by combining the fetus model and a nonpregnant-woman model that was developed previously. The developed model consists of about 7 million cubical voxels of 2 mm size and is segmented into 56 tissues and organs. This pregnant-woman model is the first completely anatomically realistic voxel model that includes a realistic fetus model and enables a numerical simulation of electromagnetic dosimetry up to the gigahertz band. In this paper, we also present the basic specific absorption rate characteristics of the pregnant-woman model exposed to vertically and horizontally polarized electromagnetic waves from 10 MHz to 2 GHz

  16. SarA is a repressor of hla (alpha-hemolysin) transcription in Staphylococcus aureus: its apparent role as an activator of hla in the prototype strain NCTC 8325 depends on reduced expression of sarS.

    Science.gov (United States)

    Oscarsson, Jan; Kanth, Anna; Tegmark-Wisell, Karin; Arvidson, Staffan

    2006-12-01

    In most Staphylococcus aureus strains, inactivation of sarA increases hla transcription, indicating that sarA is a repressor. However, in S. aureus NCTC 8325 and its derivatives, used for most studies of hla regulation, inactivation of sarA resulted in decreased hla transcription. The disparate phenotype of strain NCTC 8325 seems to be associated with its rsbU mutation, which leads to sigma(B) deficiency. This has now been verified by the demonstration that sarA repressed hla transcription in an rsbU+ derivative of strain 8325-4 (SH1000). That sarA could act as a repressor of hla in an 8325-4 background was confirmed by the observation that inactivation of sarA in an agr sarS rot triple mutant dramatically increased hla transcription to wild-type levels. However, the apparent role of sarA as an activator of hla in 8325-4 was not a result of the rsbU mutation alone, as inactivation of sarA in another rsbU mutant, strain V8, led to increased hla transcription. Northern blot analysis revealed much higher levels of sarS mRNA in strain V8 than in 8325-4, which was likely due to the mutation in the sarS activator, tcaR, in 8325-4, which was not found in strain V8. On the other hand, the relative increase in sarS transcription upon the inactivation of sarA was 15-fold higher in 8325-4 than in strain V8. Because of this, inactivation of sarA in 8325-4 means a net increase in repressor activity, whereas in strain V8, inactivation of sarA means a net decrease in repressor activity and, therefore, enhanced hla transcription.

  17. A Novel Variable Index and Excision CFAR Based Ship Detection Method on SAR Imagery

    OpenAIRE

    Ji, Kefeng; Xing, Xiangwei; Zou, Huanxin; Sun, Jixiang

    2015-01-01

    When applying the constant false alarm rate (CFAR) detector to ship detection on synthetic aperture radar (SAR) imagery, multiple interferers such as upwelling, breaking waves, ambiguities, and neighboring ships in a dense traffic area will degrade the probability of detection. In this paper, we propose a novel variable index and excision CFAR (VIE-CFAR) based ship detection method to alleviate the masking effect of multiple interferers. Firstly, we improve the variable index (VI) CFAR with a...

  18. Regional Land Subsidence Analysis in Eastern Beijing Plain by InSAR Time Series and Wavelet Transforms

    OpenAIRE

    Mingliang Gao; Huili Gong; Beibei Chen; Xiaojuan Li; Chaofan Zhou; Min Shi; Yuan Si; Zheng Chen; Guangyao Duan

    2018-01-01

    Land subsidence is the disaster phenomenon of environmental geology with regionally surface altitude lowering caused by the natural or man-made factors. Beijing, the capital city of China, has suffered from land subsidence since the 1950s, and extreme groundwater extraction has led to subsidence rates of more than 100 mm/year. In this study, we employ two SAR datasets acquired by Envisat and TerraSAR-X satellites to investigate the surface deformation in Beijing Plain from 2003 to 2013 based ...

  19. Permanent scatterer InSAR processing: Forsmark

    International Nuclear Information System (INIS)

    Dehls, John F.

    2006-04-01

    It has been speculated that slow, aseismic movement may be occurring along some of the fracture zones crosscutting the Forsmark area. The purpose of this study is to determine if it is possible to measure such movement using dInSAR. Differential SAR Interferometry (DInSAR) is a technique that compares the phases of multiple radar images of an area to measure surface change. The method has the potential to detect millimetric surface deformation along the sensor - target line-of-sight. Differences in phase between two images are easily viewed by combining, or interfering, the two phase-images. In the resulting image, the waves will either reinforce or cancel one another, depending upon the relative phases. The resulting image is called an interferogram and contains concentric bands of colour, or fringes, that are related to topography and/or surface deformation. New algorithms use many images acquired over a long time period to determine the movement history of individual objects, referred to as permanent scatterers. In the current project, standard PSInSAR processing was performed on 40 ERS-1 and ERS-2 scenes. The total area processed is approximately 1,500 km 2 . Slightly less than 20,000 permanent scatterers were identified.The highest densities were obtained along the coast and on the islands, where natural outcrops are more abundant. Two main classes of objects act as permanent scatterers in this area. The first are natural reflectors, such as rocks. The second are man-made reflectors, such as parts of buildings. Numerous local movements were found in the study area, relating to building subsidence, or compaction of anthropogenic fill. The dataset was divided into three groups for analysis, based upon the location of regional lineaments provided by SKB. Both statistical and geostatistical techniques were used. The median velocity of the three blocks did not differ by more than 0.2 mm/yr. This is not considered significant, given the possible magnitude of errors

  20. The GF-3 SAR Data Processor.

    Science.gov (United States)

    Han, Bing; Ding, Chibiao; Zhong, Lihua; Liu, Jiayin; Qiu, Xiaolan; Hu, Yuxin; Lei, Bin

    2018-03-10

    The Gaofen-3 (GF-3) data processor was developed as a workstation-based GF-3 synthetic aperture radar (SAR) data processing system. The processor consists of two vital subsystems of the GF-3 ground segment, which are referred to as data ingesting subsystem (DIS) and product generation subsystem (PGS). The primary purpose of DIS is to record and catalogue GF-3 raw data with a transferring format, and PGS is to produce slant range or geocoded imagery from the signal data. This paper presents a brief introduction of the GF-3 data processor, including descriptions of the system architecture, the processing algorithms and its output format.

  1. Two dimensional estimates from ocean SAR images

    Directory of Open Access Journals (Sweden)

    J. M. Le Caillec

    1996-01-01

    Full Text Available Synthetic Aperture Radar (SAR images of the ocean yield a lot of information on the sea-state surface providing that the mapping process between the surface and the image is clearly defined. However it is well known that SAR images exhibit non-gaussian statistics and that the motion of the scatterers on the surface, while the image is being formed, may yield to nonlinearities. The detection and quantification of these nonlinearities are made possible by using Higher Order Spectra (HOS methods and more specifically, bispectrum estimation. The development of the latter method allowed us to find phase relations between different parts of the image and to recognise their level of coupling, i.e. if and how waves of different wavelengths interacted nonlinearly. This information is quite important as the usual models assume strong nonlinearities when the waves are propagating in the azimuthal direction (i.e. along the satellite track and almost no nonlinearities when propagating in the range direction. In this paper, the mapping of the ocean surface to the SAR image is reinterpreted and a specific model (i.e. a Second Order Volterra Model is introduced. The nonlinearities are thus explained as either produced by a nonlinear system or due to waves propagating into selected directions (azimuth or range and interacting during image formation. It is shown that quadratic nonlinearities occur for waves propagating near the range direction while for those travelling in the azimuthal direction the nonlinearities, when present, are mostly due to wave interactions but are almost completely removed by the filtering effect coming from the surface motion itself (azimuth cut-off. An inherent quadratic interaction filtering (azimuth high pass filter is also present. But some other effects, apparently nonlinear, are not detected with the methods described here, meaning that either the usual relation developed for the Ocean-to-SAR transform is somewhat incomplete

  2. Permanent scatterer InSAR processing: Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Dehls, John F. [Geological Survey of Norway, Trondheim (Norway)

    2006-04-15

    It has been speculated that slow, aseismic movement may be occurring along some of the fracture zones crosscutting the Forsmark area. The purpose of this study is to determine if it is possible to measure such movement using dInSAR. Differential SAR Interferometry (DInSAR) is a technique that compares the phases of multiple radar images of an area to measure surface change. The method has the potential to detect millimetric surface deformation along the sensor - target line-of-sight. Differences in phase between two images are easily viewed by combining, or interfering, the two phase-images. In the resulting image, the waves will either reinforce or cancel one another, depending upon the relative phases. The resulting image is called an interferogram and contains concentric bands of colour, or fringes, that are related to topography and/or surface deformation. New algorithms use many images acquired over a long time period to determine the movement history of individual objects, referred to as permanent scatterers. In the current project, standard PSInSAR processing was performed on 40 ERS-1 and ERS-2 scenes. The total area processed is approximately 1,500 km{sup 2}. Slightly less than 20,000 permanent scatterers were identified.The highest densities were obtained along the coast and on the islands, where natural outcrops are more abundant. Two main classes of objects act as permanent scatterers in this area. The first are natural reflectors, such as rocks. The second are man-made reflectors, such as parts of buildings. Numerous local movements were found in the study area, relating to building subsidence, or compaction of anthropogenic fill. The dataset was divided into three groups for analysis, based upon the location of regional lineaments provided by SKB. Both statistical and geostatistical techniques were used. The median velocity of the three blocks did not differ by more than 0.2 mm/yr. This is not considered significant, given the possible magnitude of

  3. Cloaked similarity between HIV-1 and SARS-CoV suggests an anti-SARS strategy

    Directory of Open Access Journals (Sweden)

    Kliger Yossef

    2003-09-01

    Full Text Available Abstract Background Severe acute respiratory syndrome (SARS is a febrile respiratory illness. The disease has been etiologically linked to a novel coronavirus that has been named the SARS-associated coronavirus (SARS-CoV, whose genome was recently sequenced. Since it is a member of the Coronaviridae, its spike protein (S2 is believed to play a central role in viral entry by facilitating fusion between the viral and host cell membranes. The protein responsible for viral-induced membrane fusion of HIV-1 (gp41 differs in length, and has no sequence homology with S2. Results Sequence analysis reveals that the two viral proteins share the sequence motifs that construct their active conformation. These include (1 an N-terminal leucine/isoleucine zipper-like sequence, and (2 a C-terminal heptad repeat located upstream of (3 an aromatic residue-rich region juxtaposed to the (4 transmembrane segment. Conclusions This study points to a similar mode of action for the two viral proteins, suggesting that anti-viral strategy that targets the viral-induced membrane fusion step can be adopted from HIV-1 to SARS-CoV. Recently the FDA approved Enfuvirtide, a synthetic peptide corresponding to the C-terminal heptad repeat of HIV-1 gp41, as an anti-AIDS agent. Enfuvirtide and C34, another anti HIV-1 peptide, exert their inhibitory activity by binding to a leucine/isoleucine zipper-like sequence in gp41, thus inhibiting a conformational change of gp41 required for its activation. We suggest that peptides corresponding to the C-terminal heptad repeat of the S2 protein may serve as inhibitors for SARS-CoV entry.

  4. Investigation of Polarimetric SAR Data Acquired at Multiple Incidence Angles

    DEFF Research Database (Denmark)

    Svendsen, Morten Thougaard; Skriver, Henning; Thomsen, A.

    1998-01-01

    The dependence of different polarimetric parameters on the incidence angles in the range of 30° to 60° is investigated for a number of different crops using airborne SAR data. The purpose of the investigation is to determine the effect of the variation of incidence angle within a SAR image when...

  5. The Recent Severe Acute Respiratory Syndrome (SARS) Epidemic ...

    African Journals Online (AJOL)

    Severe Acute Respiratory syndrome (SARS) took the world by storm in the later part of February 2003.It is a syndrome characterized by fever, cough, sore throat , shortness of breath and malaise which may deteriorate very rapidly to respiratory failure and death. The symptoms of SARS are quite similar to those of common ...

  6. Persistent infection of SARS coronavirus in colonic cells in vitro.

    Science.gov (United States)

    Chan, Paul K S; To, Ka-Fai; Lo, Anthony W I; Cheung, Jo L K; Chu, Ida; Au, Florence W L; Tong, Joanna H M; Tam, John S; Sung, Joseph J Y; Ng, Ho-Keung

    2004-09-01

    Severe acute respiratory syndrome coronavirus (SARS-CoV) can produce gastrointestinal symptoms. The intestinal tract is the only extrapulmonary site where viable viruses have been detected. This study examined seven established human intestinal cell lines, DLD-1, HCT-116, HT-29, LoVo, LS-180, SW-480 and SW-620, for their permissiveness to SARS-CoV infection. The results showed that only LoVo cells were permissive to SARS-CoV infection as evident by positive findings from indirect immunofluorescence staining for intracellular viral antigens, in situ hybridization for intracellular viral RNA, and electron microscopy for intracellular viral particles. In contrast to Vero cells, SARS-CoV did not produce cytopathic effects on LoVo cells. However, LoVo cells were found to be highly permissive for productive infection with a high viral titre (>3 x 10(7) viral copies/ml) produced in culture supernatant following a few days of incubation. SARS-CoV established a stable persistent chronic infection that could be maintained after multiple passages. Being a cell line of human origin, LoVo cells could be a useful in vitro model for studying the biology and persistent infection of SARS-CoV. Our results on the expression of angiotensin-converting enzyme 2 (ACE2), a recently identified cellular receptor for SARS-CoV, in these cell lines indicated that it might not be the sole determinant for cells to be susceptible to SARS-CoV infection.

  7. Genome organization of the SARS-CoV

    DEFF Research Database (Denmark)

    Xu, Jing; Hu, Jianfei; Wang, Jing

    2003-01-01

    Annotation of the genome sequence of the SARS-CoV (severe acute respiratory syndrome-associated coronavirus) is indispensable to understand its evolution and pathogenesis. We have performed a full annotation of the SARS-CoV genome sequences by using annotation programs publicly available or devel...

  8. An Adaptive Ship Detection Scheme for Spaceborne SAR Imagery

    Directory of Open Access Journals (Sweden)

    Xiangguang Leng

    2016-08-01

    Full Text Available With the rapid development of spaceborne synthetic aperture radar (SAR and the increasing need of ship detection, research on adaptive ship detection in spaceborne SAR imagery is of great importance. Focusing on practical problems of ship detection, this paper presents a highly adaptive ship detection scheme for spaceborne SAR imagery. It is able to process a wide range of sensors, imaging modes and resolutions. Two main stages are identified in this paper, namely: ship candidate detection and ship discrimination. Firstly, this paper proposes an adaptive land masking method using ship size and pixel size. Secondly, taking into account the imaging mode, incidence angle, and polarization channel of SAR imagery, it implements adaptive ship candidate detection in spaceborne SAR imagery by applying different strategies to different resolution SAR images. Finally, aiming at different types of typical false alarms, this paper proposes a comprehensive ship discrimination method in spaceborne SAR imagery based on confidence level and complexity analysis. Experimental results based on RADARSAT-1, RADARSAT-2, TerraSAR-X, RS-1, and RS-3 images demonstrate that the adaptive scheme proposed in this paper is able to detect ship targets in a fast, efficient and robust way.

  9. Calibration of SAR probes in waveguide at 900 MHz

    International Nuclear Information System (INIS)

    Jokela, K.; Puranen, L.; Hyysalo, P.

    1998-01-01

    The radiation safety tests for hand-held mobile phones require precise calibration of the small electric field probes used for the measurement of SAR in phantoms simulating the human body. In this study a calibration based on a rectangular waveguide was developed for SAR calibrations at 900 MHz

  10. Molecular mechanisms of severe acute respiratory syndrome (SARS

    Directory of Open Access Journals (Sweden)

    Zabel Peter

    2005-01-01

    Full Text Available Abstract Severe acute respiratory syndrome (SARS is a new infectious disease caused by a novel coronavirus that leads to deleterious pulmonary pathological features. Due to its high morbidity and mortality and widespread occurrence, SARS has evolved as an important respiratory disease which may be encountered everywhere in the world. The virus was identified as the causative agent of SARS due to the efforts of a WHO-led laboratory network. The potential mutability of the SARS-CoV genome may lead to new SARS outbreaks and several regions of the viral genomes open reading frames have been identified which may contribute to the severe virulence of the virus. With regard to the pathogenesis of SARS, several mechanisms involving both direct effects on target cells and indirect effects via the immune system may exist. Vaccination would offer the most attractive approach to prevent new epidemics of SARS, but the development of vaccines is difficult due to missing data on the role of immune system-virus interactions and the potential mutability of the virus. Even in a situation of no new infections, SARS remains a major health hazard, as new epidemics may arise. Therefore, further experimental and clinical research is required to control the disease.

  11. Demonstrator for Automatic Target Classification in SAR Imagery

    NARCIS (Netherlands)

    Wit, J.J.M. de; Broek, A.C. van den; Dekker, R.J.

    2006-01-01

    Due to the increasing use of unmanned aerial vehicles (UAV) for reconnaissance, surveillance, and target acquisition applications, the interest in synthetic aperture radar (SAR) systems is growing. In order to facilitate the processing of the enormous amount of SAR data on the ground, automatic

  12. Project PHARUS: Towards a polarimetric C-band airborne SAR

    NARCIS (Netherlands)

    Hoogeboom, P.; Koomen, P.J.; Otten, M.P.G.; Pouwels, H.; Snoeij, P.

    1989-01-01

    A few years ago three institutes in the Netherlands developed a plan to design and build a polarimetric C-band aircraft SAR system of a novel design, called PHARUS (PHased Array Universal SAR), meant as a replacement for our current digital SLAR system. These institutes are the Physics and

  13. The Danish polarimetric SAR for remote sensing applications

    DEFF Research Database (Denmark)

    Christensen, Erik Lintz; Madsen, Søren Nørvang; Dall, Jørgen

    1994-01-01

    Presents the Danish polarimetric SAR system, EMISAR, and the approach taken in the system design to achieve a reliable high performance system. The design and implementation of the antenna system as well as the analog and digital hardware are discussed. The SAR utilises a dual polarised microstri...

  14. Reliability of SAR ADCs and associated embedded instrument detection

    NARCIS (Netherlands)

    Wan, J.; Kerkhoff, Hans G.

    2015-01-01

    Successive-approximation-register (SAR) analog-to-digital converters (ADCs) represent the majority of the ADC market from medium to high resolution ADCs. Due to its low power, high-performance and small area in Mega-Hz range, SAR ADCs are increasingly attractive for todays safe-critical applications

  15. Statistical multi-path exposure method for assessing the whole-body SAR in a heterogeneous human body model in a realistic environment.

    Science.gov (United States)

    Vermeeren, Günter; Joseph, Wout; Martens, Luc

    2013-04-01

    Assessing the whole-body absorption in a human in a realistic environment requires a statistical approach covering all possible exposure situations. This article describes the development of a statistical multi-path exposure method for heterogeneous realistic human body models. The method is applied for the 6-year-old Virtual Family boy (VFB) exposed to the GSM downlink at 950 MHz. It is shown that the whole-body SAR does not differ significantly over the different environments at an operating frequency of 950 MHz. Furthermore, the whole-body SAR in the VFB for multi-path exposure exceeds the whole-body SAR for worst-case single-incident plane wave exposure by 3.6%. Moreover, the ICNIRP reference levels are not conservative with the basic restrictions in 0.3% of the exposure samples for the VFB at the GSM downlink of 950 MHz. The homogeneous spheroid with the dielectric properties of the head suggested by the IEC underestimates the absorption compared to realistic human body models. Moreover, the variation in the whole-body SAR for realistic human body models is larger than for homogeneous spheroid models. This is mainly due to the heterogeneity of the tissues and the irregular shape of the realistic human body model compared to homogeneous spheroid human body models. Copyright © 2012 Wiley Periodicals, Inc.

  16. Assessing ScanSAR Interferometry for Deformation Studies

    Science.gov (United States)

    Buckley, S. M.; Gudipati, K.

    2007-12-01

    There is a trend in civil satellite SAR mission design to implement an imaging strategy that incorporates both stripmap mode and ScanSAR imaging. This represents a compromise between high resolution data collection and a desire for greater spatial coverage and more frequent revisit times. However, mixed mode imaging can greatly reduce the number of stripmap images available for measuring subtle ground deformation. Although ScanSAR-ScanSAR and ScanSAR-stripmap repeat-pass interferometry have been demonstrated, these approaches are infrequently used for single interferogram formation and nonexistent for InSAR time series analysis. For future mission design, e.g., a dedicated US InSAR mission, the effect of various ScanSAR system parameter choices on InSAR time series analysis also remains unexplored. Our objective is to determine the utility of ScanSAR differential interferometry. We will demonstrate the use of ScanSAR interferograms for several previous deformation studies: localized and broad-scale urban land subsidence, tunneling, volcanic surface movements and several examples associated with the seismic cycle. We also investigate the effect of various ScanSAR burst synchronization levels on our ability to detect and make quality measurements of deformation. To avoid the issues associated with Envisat ScanSAR burst alignment and to exploit a decade of InSAR measurements, we simulate ScanSAR data by bursting (throwing away range lines of) ERS-1/2 data. All the burst mode datasets are processed using a Modified SPECAN algorithm. To investigate the effects of burst misalignment, a number of cases with varying degrees of burst overlap are considered. In particular, we look at phase decorrelation as a function of percentage of burst overlap. Coherence clearly reduces as the percentage of overlap decreases and we find a useful threshold of 40-70% burst overlap depending on the study site. In order to get a more generalized understanding for different surface conditions

  17. INVENTORY OF IRRIGATED RICE ECOSYSTEM USING POLARIMETRIC SAR DATA

    Directory of Open Access Journals (Sweden)

    P. Srikanth

    2012-08-01

    Full Text Available An attempt has been made in the current study to assess the potential of polarimetric SAR data for inventory of kharif rice and the major competing crop like cotton. In the process, physical process of the scattering mechanisms occurring in rice and cotton crops at different phonological stages was studied through the use of temporal Radarsat 2 Fine quadpol SAR data. The temporal dynamics of the volume, double and odd bounce, entropy, anisotropy, alpha parameters and polarimertic signatures, classification through isodata clustering and Wishart techniques were assessed. The Wishart (H-a classification showed higher overall as well as rice and cotton crop accuracies compared to the isodata clustering from Freeman 3-component decomposition. The classification of temporal SAR data sets independently showed that the rice crop forecasting can be advanced with the use of appropriate single date polarimetric SAR data rather than using temporal SAR amplitude data sets with the single polarization in irrigated rice ecosystems

  18. MULTI-TEMPORAL SAR CHANGE DETECTION AND MONITORING

    Directory of Open Access Journals (Sweden)

    S. Hachicha

    2012-08-01

    Full Text Available Multitemporal SAR images are a very useful source of information for a large amount of applications, especially for change detection and monitoring. In this paper, a new SAR change detection and monitoring approach is proposed through the analysis of a time series of SAR images covering the same region. The first step of the method is the SAR filtering preprocessing step using an extension of the spatial NL-means filter to the temporal domain. Then, the Rayleigh Kullback Leibler and the Rayleigh Distribution Ratio measures are combined to detect the changes between a reference image and each SAR image of the time series at both local and global scale. These measures are combined using the Dezert-Smarandache theory which takes into account conflicts between sources and thus enhances the dual change detection results. Finally, a pixel based temporal classification is applied starting from the obtained change maps in order to describe the temporal behaviour of the covered regions.

  19. Guided SAR image despeckling with probabilistic non local weights

    Science.gov (United States)

    Gokul, Jithin; Nair, Madhu S.; Rajan, Jeny

    2017-12-01

    SAR images are generally corrupted by granular disturbances called speckle, which makes visual analysis and detail extraction a difficult task. Non Local despeckling techniques with probabilistic similarity has been a recent trend in SAR despeckling. To achieve effective speckle suppression without compromising detail preservation, we propose an improvement for the existing Generalized Guided Filter with Bayesian Non-Local Means (GGF-BNLM) method. The proposed method (Guided SAR Image Despeckling with Probabilistic Non Local Weights) replaces parametric constants based on heuristics in GGF-BNLM method with dynamically derived values based on the image statistics for weight computation. Proposed changes make GGF-BNLM method adaptive and as a result, significant improvement is achieved in terms of performance. Experimental analysis on SAR images shows excellent speckle reduction without compromising feature preservation when compared to GGF-BNLM method. Results are also compared with other state-of-the-art and classic SAR depseckling techniques to demonstrate the effectiveness of the proposed method.

  20. Advanced Antenna Design for NASA's EcoSAR Instrument

    Science.gov (United States)

    Du Toit, Cornelis F.; Deshpande, Manohar; Rincon, Rafael F.

    2016-01-01

    Advanced antenna arrays were designed for NASA's EcoSAR airborne radar instrument. EcoSAR is a beamforming synthetic aperture radar instrument designed to make polarimetric and "single pass" interferometric measurements of Earth surface parameters. EcoSAR's operational requirements of a 435MHz center frequency with up to 200MHz bandwidth, dual polarization, high cross-polarization isolation (> 30 dB), +/- 45deg beam scan range and antenna form-factor constraints imposed stringent requirements on the antenna design. The EcoSAR project successfully developed, characterized, and tested two array antennas in an anechoic chamber. EcoSAR's first airborne campaign conducted in the spring of 2014 generated rich data sets of scientific and engineering value, demonstrating the successful operation of the antennas.

  1. Ice flow mapping with P-band SAR

    DEFF Research Database (Denmark)

    Dall, Jørgen; Nielsen, Ulrik; Kusk, Anders

    2013-01-01

    -band SAR data have been acquired in Greenland, and both offset tracking and DInSAR have been applied to the full resolution data as well as to data degraded to the resolution of Biomass. Generally, ice velocity maps are successfully generated, but in the ablation zone, DInSAR fails in the melt season......Glacier and ice sheet dynamics are currently mapped with X-, C-, and L-band SAR. With the prospect of a P-band SAR, Biomass, to be launched within the next decade it is interesting to look into the potential of P-band for ice velocity mapping. In this paper first results are presented. Airborne P...

  2. Absorption heat pumps

    International Nuclear Information System (INIS)

    Formigoni, C.

    1998-01-01

    A brief description of the difference between a compression and an absorption heat pump is made, and the reasons why absorption systems have spread lately are given. Studies and projects recently started in the field of absorption heat pumps, as well as criteria usually followed in project development are described. An outline (performance targets, basic components) of a project on a water/air absorption heat pump, running on natural gas or LPG, is given. The project was developed by the Robur Group as an evolution of a water absorption refrigerator operating with a water/ammonia solution, which has been on the market for a long time and recently innovated. Finally, a list of the main energy and cost advantages deriving from the use of absorption heat pumps is made [it

  3. SarT, a Repressor of α-Hemolysin in Staphylococcus aureus

    Science.gov (United States)

    Schmidt, Katherine A.; Manna, Adhar C.; Gill, Steven; Cheung, Ambrose L.

    2001-01-01

    In searching the Staphylococcus aureus genome, we found several homologs to SarA. One of these genes, sarT, codes for a basic protein with 118 residues and a predicted molecular size of 16,096 Da. Northern blot analysis revealed that the expression of sarT was repressed by sarA and agr. An insertion sarT mutant generated in S. aureus RN6390 and 8325-4 backgrounds revealed minimal effect on the expression of sarR and sarA. The RNAIII level was notably increased in the sarT mutant, particularly in postexponential-phase cells, while the augmentative effect on RNAII was less. SarT repressed the expression of α-hemolysin, as determined by Northern blotting, Western blotting, and a rabbit erythrocyte hemolytic assay. This repression was relieved upon complementation. Similar to agr and sarA mutants, which predictably displayed a reduction in hla expression, the agr sarT mutant exhibited a lower level of hla transcription than the sarT mutant. In contrast, hla transcription was enhanced in the sarA sarT mutant compared with the single sarA mutant. Collectively, these results indicated that the sarA locus, contrary to the regulatory action of agr, induced α-hemolysin production by repressing sarT, a repressor of hla transcription. PMID:11447147

  4. Interseismic Deformation along the Red River Fault from InSAR Measurements

    Science.gov (United States)

    Chen, J.; Li, Z.; Clarke, P. J.

    2017-12-01

    The Red River Fault (RRF) zone is a profound geological discontinuity separating South China from Indochina. Right lateral movements along this >900 km fault are considered to accommodate the extrusion of SE China. Crustal deformation monitoring at high resolution is the key to understand the present-day mode of deformation in this zone and its interaction with the adjacent regions. This is the first study to measure the interseismic deformation of the entire fault with ALOS-1/2 and Sentinel-1 observations. Nine ascending tracks of ALOS-1 data between 2007 and 2011 are collected from the Alaska Satellite Facility (ASF), four descending tracks of Sentinel-1 data are acquired every 24 days since October 2014, and ALOS-2 data are being systematically acquired since 2014. The long wavelength (L-band) of ALOS-1/2 and short temporal baseline of Sentinel-1 ensure good coherence to overcome the limitations of heavy vegetation and variable climate in the region. Stacks of interferograms are generated by our automatic processing chain based on the InSAR Scientific Computing Environment (ISCE) software, ionospheric errors are estimated and corrected using the split-spectrum method (Fattahi et al., IEEE Trans. Geosci. Remote Sens., 2017) and the tropospheric delays are calibrated using the Generic Atmospheric Correction Online Service for InSAR (GACOS: http://ceg-research.ncl.ac.uk/v2/gacos) with high-resolution ECMWF products (Yu et al., J. Geophys. Res., 2017). Time series analysis is performed to determine the interseismic deformation rate of the RRF using the in-house InSAR time series with atmospheric estimation model (InSAR TS + AEM) package based on the Small Baseline Subset (SBAS) algorithm. Our results reveal the decrease of slip rate from north to south. We map the interseismic strain rate field to characterize the deformation patterns and seismic hazard throughout the RRF zone.

  5. SAR Image despeckling via sparse representation

    Science.gov (United States)

    Wang, Zhongmei; Yang, Xiaomei; Zheng, Liang

    2014-11-01

    SAR image despeckling is an active research area in image processing due to its importance in improving the quality of image for object detection and classification.In this paper, a new approach is proposed for multiplicative noise in SAR image removal based on nonlocal sparse representation by dictionary learning and collaborative filtering. First, a image is divided into many patches, and then a cluster is formed by clustering log-similar image patches using Fuzzy C-means (FCM). For each cluster, an over-complete dictionary is computed using the K-SVD method that iteratively updates the dictionary and the sparse coefficients. The patches belonging to the same cluster are then reconstructed by a sparse combination of the corresponding dictionary atoms. The reconstructed patches are finally collaboratively aggregated to build the denoised image. The experimental results show that the proposed method achieves much better results than many state-of-the-art algorithms in terms of both objective evaluation index (PSNR and ENL) and subjective visual perception.

  6. 3D Monitoring of Buildings Using TerraSAR-X InSAR, DInSAR and PolSAR Capacities

    Directory of Open Access Journals (Sweden)

    Flora Weissgerber

    2017-09-01

    Full Text Available The rapid expansion of cities increases the need of urban remote sensing for a large scale monitoring. This paper provides greater understanding of how TerraSAR-X (TSX high-resolution abilities enable to reach the spatial precision required to monitor individual buildings, through the use of a 4 year temporal stack of 100 images over Paris (France. Three different SAR modes are investigated for this purpose. First a method involving a whole time-series is proposed to measure realistic heights of buildings. Then, we show that the small wavelength of TSX makes the interferometric products very sensitive to the ordinary building-deformation, and that daily deformation can be measured over the entire building with a centimetric accuracy, and without any a priori on the deformation evolution, even when neglecting the impact of the atmosphere. Deformations up to 4 cm were estimated for the Eiffel Tower and up to 1 cm for other lower buildings. These deformations were analyzed and validated with weather and in situ local data. Finally, four TSX polarimetric images were used to investigate geometric and dielectric properties of buildings under the deterministic framework. Despite of the resolution loss of this mode, the possibility to estimate the structural elements of a building orientations and their relative complexity in the spatial organization are demonstrated.

  7. Modelling of potentially promising SARS protease inhibitors

    Energy Technology Data Exchange (ETDEWEB)

    Plewczynski, Dariusz [Interdisciplinary Centre for Mathematical and Computational Modelling, ICM, Warsaw University, Pawinskiego 5a Street, 02-106 Warsaw (Poland); Hoffmann, Marcin [BioInfoBank Institute, Limanowskiego 24A/16, 60-744 Poznan (Poland); Grotthuss, Marcin von [BioInfoBank Institute, Limanowskiego 24A/16, 60-744 Poznan (Poland); Knizewski, Lukasz [Interdisciplinary Centre for Mathematical and Computational Modelling, ICM, Warsaw University, Pawinskiego 5a Street, 02-106 Warsaw (Poland); Rychewski, Leszek [BioInfoBank Institute, Limanowskiego 24A/16, 60-744 Poznan (Poland); Eitner, Krystian [BioInfoBank Institute, Limanowskiego 24A/16, 60-744 Poznan (Poland); Ginalski, Krzysztof [Interdisciplinary Centre for Mathematical and Computational Modelling, ICM, Warsaw University, Pawinskiego 5a Street, 02-106 Warsaw (Poland)

    2007-07-18

    In many cases, at the beginning of a high throughput screening experiment some information about active molecules is already available. Active compounds (such as substrate analogues, natural products and inhibitors of related proteins) are often identified in low throughput validation studies on a biochemical target. Sometimes the additional structural information is also available from crystallographic studies on protein and ligand complexes. In addition, the structural or sequence similarity of various protein targets yields a novel possibility for drug discovery. Co-crystallized compounds from homologous proteins can be used to design leads for a new target without co-crystallized ligands. In this paper we evaluate how far such an approach can be used in a real drug campaign, with severe acute respiratory syndrome (SARS) coronavirus providing an example. Our method is able to construct small molecules as plausible inhibitors solely on the basis of the set of ligands from crystallized complexes of a protein target, and other proteins from its structurally homologous family. The accuracy and sensitivity of the method are estimated here by the subsequent use of an electronic high throughput screening flexible docking algorithm. The best performing ligands are then used for a very restrictive similarity search for potential inhibitors of the SARS protease within the million compounds from the Ligand.Info small molecule meta-database. The selected molecules can be passed on for further experimental validation.

  8. The Ecosystems SAR (EcoSAR) an Airborne P-band Polarimetric InSAR for the Measurement of Vegetation Structure, Biomass and Permafrost

    Science.gov (United States)

    Rincon, Rafael F.; Fatoyinbo, Temilola; Ranson, K. Jon; Osmanoglu, Batuhan; Sun, Guoqing; Deshpande, Manohar D.; Perrine, Martin L.; Du Toit, Cornelis F.; Bonds, Quenton; Beck, Jaclyn; hide

    2014-01-01

    EcoSAR is a new synthetic aperture radar (SAR) instrument being developed at the NASA/ Goddard Space Flight Center (GSFC) for the polarimetric and interferometric measurements of ecosystem structure and biomass. The instrument uses a phased-array beamforming architecture and supports full polarimetric measurements and single pass interferometry. This Instrument development is part of NASA's Earth Science Technology Office Instrument Incubator Program (ESTO IIP).

  9. Water absorption characteristic of interlocking compressed earth brick units

    Science.gov (United States)

    Bakar, B. H. Abu; Saari, S.; Surip, N. A.

    2017-10-01

    This study aims to investigate the water absorption characteristic of interlocking compressed earth brick (ICEB) units. Apart from compressive strength, water absorption is an important property in masonry. This property can affect the quality of the brick itself and the bond strength between the brick and mortar in masonry structures and can result in reducing its strength properties. The units were tested for 24 h water absorption and 5 h boiling water absorption. A total of 170 ICEB units from four ICEB types underwent both tests. For the 24 h water absorption, the ICEB units were dried in the oven for 24 h and then cooled before being weighed. Thereafter, each brick was immersed in water for 24 h and weighed. The same specimens used for the 24 h water absorption test were re-used for the 5 h boiling water absorption test. After completing the 24 h water absorption test, the brick was boiled for 5-hours and weighed. The highest water absorption for the ICEBs in the 24-hour water absorption and 5 h boiling water absorption tests are 15.09% and 17.18%, respectively. The half brick has the highest water absorption (15.87%), whereas the beam brick has the lowest (13.20%). The water absorption of an ICEB unit is higher than that of normal bricks, although the water absorption of the former remains below the maximum rate of the brick water absorption (21%).

  10. A parametric study of rate of advance and area coverage rate performance of synthetic aperture radar.

    Energy Technology Data Exchange (ETDEWEB)

    Raynal, Ann Marie [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Hensley, Jr., William H. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Burns, Bryan L. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Doerry, Armin Walter [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2014-11-01

    The linear ground distance per unit time and ground area covered per unit time of producing synthetic aperture radar (SAR) imagery, termed rate of advance (ROA) and area coverage rate (ACR), are important metrics for platform and radar performance in surveillance applications. These metrics depend on many parameters of a SAR system such as wavelength, aircraft velocity, resolution, antenna beamwidth, imaging mode, and geometry. Often the effects of these parameters on rate of advance and area coverage rate are non-linear. This report addresses the impact of different parameter spaces as they relate to rate of advance and area coverage rate performance.

  11. Ship Detection in High-Resolution Dual-Polarization SAR Amplitude Images

    Directory of Open Access Journals (Sweden)

    Gui Gao

    2013-01-01

    Full Text Available A constant false alarm rate (CFAR detecting method for ships in high-resolution dual-polarization synthetic aperture radar (SAR amplitude images has been proposed in this paper. First, by the production of amplitude images from two polarimetric channels, a novel detector simply called the PMA detector has been constructed. We testified that the PMA detector could improve the signal-to-clutter ratio (SCR and make the discrimination of a ship from clutter more easily. Second, the PMA detector’s statistical model has been described by the well-known distribution when facing complex sea background. The experiments performed on measured dual-polarization TerraSAR-X images demonstrate the good performance of the proposed CFAR detecting method.

  12. Aircraft Detection in High-Resolution SAR Images Based on a Gradient Textural Saliency Map

    Directory of Open Access Journals (Sweden)

    Yihua Tan

    2015-09-01

    Full Text Available This paper proposes a new automatic and adaptive aircraft target detection algorithm in high-resolution synthetic aperture radar (SAR images of airport. The proposed method is based on gradient textural saliency map under the contextual cues of apron area. Firstly, the candidate regions with the possible existence of airport are detected from the apron area. Secondly, directional local gradient distribution detector is used to obtain a gradient textural saliency map in the favor of the candidate regions. In addition, the final targets will be detected by segmenting the saliency map using CFAR-type algorithm. The real high-resolution airborne SAR image data is used to verify the proposed algorithm. The results demonstrate that this algorithm can detect aircraft targets quickly and accurately, and decrease the false alarm rate.

  13. Aircraft Detection in High-Resolution SAR Images Based on a Gradient Textural Saliency Map.

    Science.gov (United States)

    Tan, Yihua; Li, Qingyun; Li, Yansheng; Tian, Jinwen

    2015-09-11

    This paper proposes a new automatic and adaptive aircraft target detection algorithm in high-resolution synthetic aperture radar (SAR) images of airport. The proposed method is based on gradient textural saliency map under the contextual cues of apron area. Firstly, the candidate regions with the possible existence of airport are detected from the apron area. Secondly, directional local gradient distribution detector is used to obtain a gradient textural saliency map in the favor of the candidate regions. In addition, the final targets will be detected by segmenting the saliency map using CFAR-type algorithm. The real high-resolution airborne SAR image data is used to verify the proposed algorithm. The results demonstrate that this algorithm can detect aircraft targets quickly and accurately, and decrease the false alarm rate.

  14. Fast iterative censoring CFAR algorithm for ship detection from SAR images

    Science.gov (United States)

    Gu, Dandan; Yue, Hui; Zhang, Yuan; Gao, Pengcheng

    2017-11-01

    Ship detection is one of the essential techniques for ship recognition from synthetic aperture radar (SAR) images. This paper presents a fast iterative detection procedure to eliminate the influence of target returns on the estimation of local sea clutter distributions for constant false alarm rate (CFAR) detectors. A fast block detector is first employed to extract potential target sub-images; and then, an iterative censoring CFAR algorithm is used to detect ship candidates from each target blocks adaptively and efficiently, where parallel detection is available, and statistical parameters of G0 distribution fitting local sea clutter well can be quickly estimated based on an integral image operator. Experimental results of TerraSAR-X images demonstrate the effectiveness of the proposed technique.

  15. An offset cancellation technique in a switched-capacitor comparator for SAR ADCs

    International Nuclear Information System (INIS)

    Tong Xingyuan; Zhu Zhangming; Yang Yintang

    2012-01-01

    An offset cancellation technique for a SAR (successive approximation register) ADC switched-capacitor comparator is described. The comparator is designed with a pre-amplifying and regenerative latching structure and realized in 0.18 μm CMOS. With the first stage preamplifier offset cancellation and low offset regenerative latching approach, the equivalent offset of the comparator is reduced to < 0.55 mV. By using the pre-amplifying and regenerative latching comparison mode the comparator exhibits low power dissipation. Under a 1.8 V power supply, with a 200 kS/s ADC sampling rate and 3 MHz clock frequency, a 13-bit comparison resolution is reached and less than 0.09 mW power dissipation is consumed. The superiority of this comparator is discussed and proved by the post-simulation and application to a 10 bit 200 kS/s touch screen SAR A/D converter. (semiconductor integrated circuits)

  16. Bryan Mound InSAR Analysis U.S. Strategic petroleum Reserve.

    Energy Technology Data Exchange (ETDEWEB)

    Lord, Anna C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-06-01

    The U.S. Strategic Petroleum Reserve (SPR) is a stockpile of emergency crude oil to be tapped into if a disruption in the nation's oil supply occurs. The SPR is comprised of four salt dome sites. Subsidence surveys have been conducted either annually or biennially at all four sites over the life of the program. Monitoring of surface behavior is a first line defense to detecting possible subsurface cavern integrity issues. Over the life of the Bryan Mound site, subsidence rates over abandoned Cavern 3 have continuously been the highest at the site. In an effort to try and understand the subsurface dynamics, specifically over Bryan Mound Cavern 3, historic interferometric synthetic aperture radar (InSAR) data was acquired and processed by TRE Altamira. InSAR involves the processing of multiple satellite synthetic aperture radar scenes acquired across the same location of the Earth's surface at different times to map surface deformation. The analysis of the data has the ability to detect millimeters of motion spanning days, months, year and decades, across specific sites. The intent in regards to the Bryan Mound site was (1) to confirm the higher subsidence rates recorded over abandoned Cavern 3 indicated by land survey and (2) understand the regional surface behavior. This report describes the InSAR analysis results, how those results compare to the historical collection of land survey data, and what additional information the data has provided towards understanding the response recorded at the surface.

  17. Adsorption Isotherms of Boron in Soil: the effects of Sodium Adsorption Ratio (SAR, pH and Ionic strength

    Directory of Open Access Journals (Sweden)

    Mojtaba Moqbeli

    2017-03-01

    solution after filtration, from added boron. Results and Discussion: The Langmuir isotherm waswell fitted to the adsorbtiondata based on the R2 and SEE.At different IS and SAR levels, the soil exhibited different adsorption behaviors. The effect of SAR on the boron adsorption was greater at high concentrations.The results showed the increase in sodium adsorption ratio,increased soil pH and Boron adsorption.An increase in sodium adsorption ratio up to 100 resulted in a small increase in Boron adsorption compared to SAR=20. With sodium adsorption ratio of 100, soil pHincreased from 8.3 to 8.7. At about PH=9.5, maximum adsorption occurs because boron dissociation is greater when pka = pH. Increasing ionic strength increased the boron adsorption; the absorption rate wasmuch higher at higher ionic strength.Model-predicted and experimental parameters obtained using the Langmuir equation pointed to the large effect of salt concentration on the boron adsorption which wasan increase of around 10% and 75% in q max as a result of an increase in salt concentration from 0.02 to 0.06 and 0.12 M respectively. We can ignore the effect ofsalt at very low equilibrium concentration; however, it increases gradually with increasing the equilibrium concentration of boron. Conclusions: The results of the present study showed that sodium adsorption ratio was low, in low equilibrium concentration related to low boron concentration, but the equilibrium concentration of boron increased with increasing the sodium adsorption ratio.In sodium adsorptionratio of 100, increasing pH increased the adsorption of boron. Boron adsorption was increased with increasing ionic strength; the adsorption rate was muchhigher than the rate of increase in ionic strength.Increasing the ionic strength suppresses the DDL on planar surface and therefore more negative borate ions are able to move close enough to interact with the adsorption sites located on the edge surfaces. Assuming that this phenomenon affects the

  18. VenSAR on EnVision: Taking earth observation radar to Venus

    Science.gov (United States)

    Ghail, Richard C.; Hall, David; Mason, Philippa J.; Herrick, Robert R.; Carter, Lynn M.; Williams, Ed

    2018-02-01

    Venus should be the most Earth-like of all our planetary neighbours: its size, bulk composition and distance from the Sun are very similar to those of Earth. How and why did it all go wrong for Venus? What lessons can be learned about the life story of terrestrial planets in general, in this era of discovery of Earth-like exoplanets? Were the radically different evolutionary paths of Earth and Venus driven solely by distance from the Sun, or do internal dynamics, geological activity, volcanic outgassing and weathering also play an important part? EnVision is a proposed ESA Medium class mission designed to take Earth Observation technology to Venus to measure its current rate of geological activity, determine its geological history, and the origin and maintenance of its hostile atmosphere, to understand how Venus and Earth could have evolved so differently. EnVision will carry three instruments: the Venus Emission Mapper (VEM); the Subsurface Radar Sounder (SRS); and VenSAR, a world-leading European phased array synthetic aperture radar that is the subject of this article. VenSAR will obtain images at a range of spatial resolutions from 30 m regional coverage to 1 m images of selected areas; an improvement of two orders of magnitude on Magellan images; measure topography at 15 m resolution vertical and 60 m spatially from stereo and InSAR data; detect cm-scale change through differential InSAR, to characterise volcanic and tectonic activity, and estimate rates of weathering and surface alteration; and characterise of surface mechanical properties and weathering through multi-polar radar data. These data will be directly comparable with Earth Observation radar data, giving geoscientists unique access to an Earth-sized planet that has evolved on a radically different path to our own, offering new insights on the Earth-sized exoplanets across the galaxy.

  19. First Results from Sentinel-1A InSAR over Australia: Application to the Perth Basin

    Directory of Open Access Journals (Sweden)

    Amy L. Parker

    2017-03-01

    Full Text Available Past ground-based geodetic measurements in the Perth Basin, Australia, record small-magnitude subsidence (up to 7 mm/y, but are limited to discrete points or traverses across parts of the metropolitan area. Here, we investigate deformation over a much larger region by performing the first application of Sentinel-1A InSAR data to Australia. The duration of the study is short (0.7 y, as dictated by the availability of Sentinel-1A data. Despite this limited observation period, verification of Sentinel-1A with continuous GPS and independent TerraSAR-X provides new insights into the deformation field of the Perth Basin. The displacements recorded by each satellite are in agreement, identifying broad (>5 km wide areas of subsidence at rates up to 15 mm/y. Subsidence at rates greater than 20 mm/y over smaller regions (∼2 km wide is coincident with wetland areas, where displacements are temporally correlated with changes in groundwater levels in the unconfined aquifer. Longer InSAR time series are required to determine whether these measured displacements are representative of long-term deformation or (more likely seasonal variations. However, the agreement between datasets demonstrates the ability of Sentinel-1A to detect small-magnitude deformation over different spatial scales (from 2 km–10 s of km in the Perth Basin. We suggest that, even over short time periods, these data are useful as a reconnaissance tool to identify regions for subsequent targeted studies, particularly given the large swath size of radar acquisitions, which facilitates analysis of a broader portion of the deformation field than ground-based methods or single scenes of TerraSAR-X.

  20. Solar absorption surface panel

    Science.gov (United States)

    Santala, Teuvo J.

    1978-01-01

    A composite metal of aluminum and nickel is used to form an economical solar absorption surface for a collector plate wherein an intermetallic compound of the aluminum and nickel provides a surface morphology with high absorptance and relatively low infrared emittance along with good durability.

  1. Nutrition and magnesium absorption

    NARCIS (Netherlands)

    Brink, E.J.

    1992-01-01

    The influence of various nutrients present in dairy products and soybean-based products on absorption of magnesium has been investigated. The studies demonstrate that soybean protein versus casein lowers apparent magnesium absorption in rats through its phytate component. However, true

  2. Zeeman atomic absorption spectroscopy

    International Nuclear Information System (INIS)

    Loos-Vollebregt, M.T.C. de.

    1980-01-01

    A new method of background correction in atomic absorption spectroscopy has recently been introduced, based on the Zeeman splitting of spectral lines in a magnetic field. A theoretical analysis of the background correction capability observed in such instruments is presented. A Zeeman atomic absorption spectrometer utilizing a 50 Hz sine wave modulated magnetic field is described. (Auth.)

  3. 76 FR 35949 - Agency Information Collection Activity (Servicer's Staff Appraisal Reviewer (SAR) Application...

    Science.gov (United States)

    2011-06-20

    ... Collection Activity (Servicer's Staff Appraisal Reviewer (SAR) Application) Under OMB Review AGENCY: Veterans...: Servicer's Staff Appraisal Reviewer (SAR) Application, VA Form 26-0829. OMB Control Number: 2900-0715. Type... servicers to nominate employees for approval as Staff Appraisal Reviewer (SAR). Servicers SAR's will have...

  4. Spacial Variation in SAR Images of Different Resolution for Agricultural Fields

    DEFF Research Database (Denmark)

    Sandholt, Inge; Skriver, Henning

    1999-01-01

    The spatial variation in two types of Synthetic Aperture Radar (SAR) images covering agricultural fields is analysed. C-band polarimetric SAR data from the Danish airborne SAR, EMISAR, have been compared to space based ERS-1 C-band SAR with respect to scale and effect of polarization. The general...

  5. [Comparative study of absorption kinetics in intestines of rats on Xianlinggubao capsule prepared by different technologies].

    Science.gov (United States)

    Wu, Huichao; Du, Shouying; Lu, Yang; Chen, Wen; Ma, Yong; Li, Pengyue

    2011-04-01

    To study the characteristics of intestinal absorption of psoralen and isopsoralen of Xianlinggubao capsule, and compare the absorption of Xianlinggubao capsule prepared by different technologies. Non everted gut sac method was applied to investigate the influence of absorption sites and drug concentration on psoralen and isopsoralen absorption, which were determined by HPLC. Although the absorption rate constants of psoralen and isopsoralen in duodenum were more than that in jejunum and ileum, there was no significance difference between them. The absorption rate constants of psoralen kept at the same level when the concentrations of drug solution were at middle and low level, while the absorption rate constant at high level was absolutely lower than them (P Intestinal absorption of psoralen and isopsoralen may be affected by the dissolution. The absorption rate constants of psoralen and isopsoralen in new Xianlinggubao capsules are higher. The absorptions of active components absorption has significant difference in different preparation processes of Xianlinggubao capsule.

  6. Research on Airborne SAR Imaging Based on Esc Algorithm

    Science.gov (United States)

    Dong, X. T.; Yue, X. J.; Zhao, Y. H.; Han, C. M.

    2017-09-01

    Due to the ability of flexible, accurate, and fast obtaining abundant information, airborne SAR is significant in the field of Earth Observation and many other applications. Optimally the flight paths are straight lines, but in reality it is not the case since some portion of deviation from the ideal path is impossible to avoid. A small disturbance from the ideal line will have a major effect on the signal phase, dramatically deteriorating the quality of SAR images and data. Therefore, to get accurate echo information and radar images, it is essential to measure and compensate for nonlinear motion of antenna trajectories. By means of compensating each flying trajectory to its reference track, MOCO method corrects linear phase error and quadratic phase error caused by nonlinear antenna trajectories. Position and Orientation System (POS) data is applied to acquiring accuracy motion attitudes and spatial positions of antenna phase centre (APC). In this paper, extend chirp scaling algorithm (ECS) is used to deal with echo data of airborne SAR. An experiment is done using VV-Polarization raw data of C-band airborne SAR. The quality evaluations of compensated SAR images and uncompensated SAR images are done in the experiment. The former always performs better than the latter. After MOCO processing, azimuth ambiguity is declined, peak side lobe ratio (PSLR) effectively improves and the resolution of images is improved obviously. The result shows the validity and operability of the imaging process for airborne SAR.

  7. RESEARCH ON AIRBORNE SAR IMAGING BASED ON ESC ALGORITHM

    Directory of Open Access Journals (Sweden)

    X. T. Dong

    2017-09-01

    Full Text Available Due to the ability of flexible, accurate, and fast obtaining abundant information, airborne SAR is significant in the field of Earth Observation and many other applications. Optimally the flight paths are straight lines, but in reality it is not the case since some portion of deviation from the ideal path is impossible to avoid. A small disturbance from the ideal line will have a major effect on the signal phase, dramatically deteriorating the quality of SAR images and data. Therefore, to get accurate echo information and radar images, it is essential to measure and compensate for nonlinear motion of antenna trajectories. By means of compensating each flying trajectory to its reference track, MOCO method corrects linear phase error and quadratic phase error caused by nonlinear antenna trajectories. Position and Orientation System (POS data is applied to acquiring accuracy motion attitudes and spatial positions of antenna phase centre (APC. In this paper, extend chirp scaling algorithm (ECS is used to deal with echo data of airborne SAR. An experiment is done using VV-Polarization raw data of C-band airborne SAR. The quality evaluations of compensated SAR images and uncompensated SAR images are done in the experiment. The former always performs better than the latter. After MOCO processing, azimuth ambiguity is declined, peak side lobe ratio (PSLR effectively improves and the resolution of images is improved obviously. The result shows the validity and operability of the imaging process for airborne SAR.

  8. Advanced InSAR techniques for the management and characterization of geothermal resources

    Science.gov (United States)

    Bellotti, F.; Falorni, G.; Morgan, J.; Rucci, A.; Ferretti, A.

    2012-04-01

    response to high rates of water injection, with a strong interest in researching induced seismicity and ground deformation. These studies, along with the continuing developments in radar satellite technology and in the field of InSAR, show considerable promise for the future monitoring of geothermal production facilities.

  9. The experience of SARS-related stigma at Amoy Gardens.

    Science.gov (United States)

    Lee, Sing; Chan, Lydia Y Y; Chau, Annie M Y; Kwok, Kathleen P S; Kleinman, Arthur

    2005-11-01

    Severe Acute Respiratory Syndrome (SARS) possesses characteristics that render it particularly prone to stigmatization. SARS-related stigma, despite its salience for public health and stigma research, has had little examination. This study combines survey and case study methods to examine subjective stigma among residents of Amoy Gardens (AG), the first officially recognized site of community outbreak of SARS in Hong Kong. A total of 903 residents of AG completed a self-report questionnaire derived from two focus groups conducted toward the end of the 3-month outbreak. Case studies of two residents who lived in Block E, the heart of the SARS epidemic at AG, complement the survey data. Findings show that stigma affected most residents and took various forms of being shunned, insulted, marginalized, and rejected in the domains of work, interpersonal relationships, use of services and schooling. Stigma was also associated with psychosomatic distress. Residents' strategies for diminishing stigma varied with gender, age, education, occupation, and proximity to perceived risk factors for SARS such as residential location, previous SARS infection and the presence of ex-SARS household members. Residents attributed stigma to government mismanagement, contagiousness of the mysterious SARS virus, and alarmist media reporting. Stigma clearly decreased, but never completely disappeared, after the outbreak. The findings confirm and add to existing knowledge on the varied origins, correlates, and impacts of stigma. They also highlight the synergistic roles of inconsistent health policy responses and risk miscommunication by the media in rapidly amplifying stigma toward an unfamiliar illness. While recognizing the intrinsically stigmatizing nature of public health measures to control SARS, we recommend that a consistent inter-sectoral approach is needed to minimize stigma and to make an effective health response to future outbreaks.

  10. FlexSAR, a high quality, flexible, cost effective, prototype SAR system

    Science.gov (United States)

    Jensen, Mark; Knight, Chad; Haslem, Brent

    2016-05-01

    The FlexSAR radar system was designed to be a high quality, low-cost, flexible research prototype instrument. Radar researchers and practitioners often desire the ability to prototype new or advanced configurations, yet the ability to enhance or upgrade existing radar systems can be cost prohibitive. FlexSAR answers the need for a flexible radar system that can be extended easily, with minimal cost and time expenditures. The design approach focuses on reducing the resources required for developing and validating new advanced radar modalities. Such an approach fosters innovation and provides risk reduction since actual radar data can be collected in the appropriate mode, processed, and analyzed early in the development process. This allows for an accurate, detailed understanding of the corresponding trade space. This paper is a follow-on to last years paper and discusses the advancements that have been made to the FlexSAR system. The overall system architecture is discussed and presented along with several examples illustrating the system utility.

  11. A Comparison of Seasonal Patterns Observed in ERS 1 / 2 Differential InSAR, Groundwater Level Data, and Groundwater Production Data in Reno, Nevada, USA.

    Science.gov (United States)

    Oppliger, G. L.; Goudy, C.; Widmer, M.

    2005-12-01

    We report on a comparison of repeating seasonal patterns observed in ERS 1 / 2 differential InSAR, (D-InSAR) groundwater level (GWL) data, and water production volume data in Reno, Nevada, USA. Over the 1992-2002 study period we found municipal groundwater utilization in the Reno study area was associated with centimeter and sub-centimeter surface elevation changes which are distributed over aquifer related zones several kilometers in width. In the central Reno area observations define two active anomaly areas which show cyclical surface deflation and inflation with elevation changes of 10 to 30 millimeters over one to nine years. Seasonal groundwater level change associated with these D-InSAR features ranged between 0.3 and 3 meters. Some D-InSAR pattern perimeters are localized by geologic structure while others are more mobile. Most surface deflation appears to be periodically restored by natural and managed aquifer recharge. The area's of active surface inflation-deflation nominally correspond with the area's most significantly utilized groundwater aquifers. To evaluate evidence for the direct relation between D-InSAR and groundwater production in the study area, comparisons between 1992-2002 groundwater levels, production rates and D-InSAR surface inflation-deflation features were developed. Groundwater level change maps showed good direct correlations with D-InSAR observations only in areas where the GWL changes were relatively large (~10 meters), spatially uniform and sustained over several years. Several factors probably contribute to the weak correlation of many GWL's and D-InSAR features including: incomplete GWL coverages, GWL monitoring data representing different aquifer horizons, proximity to production wells, delayed development of aquifer volume change when water levels are altered, and lateral change in aquifer composition. Consistency of the D-InSAR features suggests atmospheric artifacts were not the source of the discrepancies. Some of the

  12. Wind mapping offshore in coastal Mediterranean area using SAR images

    DEFF Research Database (Denmark)

    Calaudi, Rosamaria; Arena, Felice; Badger, Merete

    Satellite observations of the ocean surface from Synthetic Aperture Radars (SAR) provide information about the spatial wind variability over large areas. This is of special interest in the Mediterranean, where spatial wind information is only provided by sparse buoys, often with long periods...... of missing data. Here, we focus on evaluating the use of SAR for offshore wind mapping. Preliminary results from the analysis of SAR-based ocean winds in Mediterranean areas show interesting large scale wind flow features consistent with results from previous studies using numerical models and space borne...

  13. Pre-Processes for Urban Areas Detection in SAR Images

    Science.gov (United States)

    Altay Açar, S.; Bayır, Ş.

    2017-11-01

    In this study, pre-processes for urban areas detection in synthetic aperture radar (SAR) images are examined. These pre-processes are image smoothing, thresholding and white coloured regions determination. Image smoothing is carried out to remove noises then thresholding is applied to obtain binary image. Finally, candidate urban areas are detected by using white coloured regions determination. All pre-processes are applied by utilizing the developed software. Two different SAR images which are acquired by TerraSAR-X are used in experimental study. Obtained results are shown visually.

  14. SAR image effects on coherence and coherence estimation.

    Energy Technology Data Exchange (ETDEWEB)

    Bickel, Douglas Lloyd

    2014-01-01

    Radar coherence is an important concept for imaging radar systems such as synthetic aperture radar (SAR). This document quantifies some of the effects in SAR which modify the coherence. Although these effects can disrupt the coherence within a single SAR image, this report will focus on the coherence between separate images, such as for coherent change detection (CCD) processing. There have been other presentations on aspects of this material in the past. The intent of this report is to bring various issues that affect the coherence together in a single report to support radar engineers in making decisions about these matters.

  15. Mapping and monitoring renewable resources with space SAR

    Science.gov (United States)

    Ulaby, F. T.; Brisco, B.; Dobson, M. C.; Moezzi, S.

    1983-01-01

    The SEASAT-A SAR and SIR-A imagery was examined to evaluate the quality and type of information that can be extracted and used to monitor renewable resources on Earth. Two tasks were carried out: (1) a land cover classification study which utilized two sets of imagery acquired by the SEASAT-A SAR, one set by SIR-A, and one LANDSAT set (4 bands); and (2) a change detection to examine differences between pairs of SEASAT-A SAR images and relates them to hydrologic and/or agronomic variations in the scene.

  16. Compact polarimetric SAR product and calibration considerations for target analysis

    Science.gov (United States)

    Sabry, Ramin

    2016-10-01

    Compact polarimetric (CP) data exploitation is currently of growing interest considering the new generation of such Synthetic Aperture Radar (SAR) systems. These systems offer target detection and classification capabilities comparable to those of polarimetric SARs (PolSAR) with less stringent requirements. A good example is the RADARSAT Constellation Mission (RCM). In this paper, some characteristic CP products are described and effects of CP mode deviation from ideal circular polarization transmit on classifications are modeled. The latter is important for operation of typical CP modes (e.g., RCM). The developed model can be used to estimate the ellipticity variation from CP measured data, and hence, calibrate the classification products.

  17. SAR antenna design for ambiguity and multipath suppression

    DEFF Research Database (Denmark)

    Christensen, Erik Lintz; Dich, Mikael

    1993-01-01

    A high resolution airborne synthetic aperture radar (SAR) has been developed at the Electromagnetics Institute (EMI) for remote sensing applications. The paper considers the radiation of antennas for a SAR system from a systems perspective. The basic specifications of an idealised antenna...... are obtained from the required swath and the azimuth footprint needed for the SAR processing. The radiation from a real antenna causes unwanted signal returns that lead to intensity variations (multipath) and ghost echoes (ambiguity). Additional specifications are deduced by considering these signals...

  18. A RAIL CENTRAL DISPLACEMENT METHOD ABOUT GB-SAR

    OpenAIRE

    J. Peng; J. Cai; H. Yang

    2016-01-01

    This paper presents a new method to correct rail errors of Ground Based Synthetic Aperture Radar (GB-SAR) in the discontinue mode. Generally, “light positioning” is performed to mark the GB-SAR position in the dis-continuous observation mode. Usually we assume there is no difference between the marked position and the real installation position. But in fact, it is hard to keep the GB-SAR positions of two campaigns the same, so repositioning errors can’t be neglected. In order to solve this pr...

  19. From genome to antivirals: SARS as a test tube.

    Science.gov (United States)

    Kliger, Yossef; Levanon, Erez Y; Gerber, Doron

    2005-03-01

    The severe acute respiratory syndrome (SARS) epidemic brought into the spotlight the need for rapid development of effective anti-viral drugs against newly emerging viruses. Researchers have leveraged the 20-year battle against AIDS into a variety of possible treatments for SARS. Most prominently, based solely on viral genome information, silencers of viral genes, viral-enzyme blockers and viral-entry inhibitors were suggested as potential therapeutic agents for SARS. In particular, inhibitors of viral entry, comprising therapeutic peptides, were based on the recently launched anti-HIV drug enfuvirtide. This could represent one of the most direct routes from genome sequencing to the discovery of antiviral drugs.

  20. Program Merges SAR Data on Terrain and Vegetation Heights

    Science.gov (United States)

    Siqueira, Paul; Hensley, Scott; Rodriguez, Ernesto; Simard, Marc

    2007-01-01

    X/P Merge is a computer program that estimates ground-surface elevations and vegetation heights from multiple sets of data acquired by the GeoSAR instrument [a terrain-mapping synthetic-aperture radar (SAR) system that operates in the X and bands]. X/P Merge software combines data from X- and P-band digital elevation models, SAR backscatter magnitudes, and interferometric correlation magnitudes into a simplified set of output topographical maps of ground-surface elevation and tree height.

  1. SAR polar format implementation with MATLAB.

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Grant D.; Doerry, Armin Walter

    2005-11-01

    Traditional polar format image formation for Synthetic Aperture Radar (SAR) requires a large amount of processing power and memory in order to accomplish in real-time. These requirements can thus eliminate the possible usage of interpreted language environments such as MATLAB. However, with trapezoidal aperture phase history collection and changes to the traditional polar format algorithm, certain optimizations make MATLAB a possible tool for image formation. Thus, this document's purpose is two-fold. The first outlines a change to the existing Polar Format MATLAB implementation utilizing the Chirp Z-Transform that improves performance and memory usage achieving near realtime results for smaller apertures. The second is the addition of two new possible image formation options that perform a more traditional interpolation style image formation. These options allow the continued exploration of possible interpolation methods for image formation and some preliminary results comparing image quality are given.

  2. Cross-calibration of interferometric SAR data

    DEFF Research Database (Denmark)

    Dall, Jørgen

    2003-01-01

    Generation of digital elevation models from interferometric synthetic aperture radar (SAR) data is a well established technique. Achieving a high geometric fidelity calls for a calibration accounting for inaccurate navigation data and system parameters as well as system imperfections. Fully......, but not necessarily from map to map. It is based on natural distributed targets for which no a priori knowledge is needed. In particular, no DEM is required as in calibration techniques based on dedicated calibration scenes. To achieve absolute calibration, i.e. elimination of a constant elevation offset, a single...... ground control point is often needed. The paper presents the principles and mathematics of the cross-calibration technique and illustrates its successful application to EMISAR data....

  3. A NEW SAR CLASSIFICATION SCHEME FOR SEDIMENTS ON INTERTIDAL FLATS BASED ON MULTI-FREQUENCY POLARIMETRIC SAR IMAGERY

    Directory of Open Access Journals (Sweden)

    W. Wang

    2017-11-01

    Full Text Available We present a new classification scheme for muddy and sandy sediments on exposed intertidal flats, which is based on synthetic aperture radar (SAR data, and use ALOS-2 (L-band, Radarsat-2 (C-band and TerraSAR-X (X-band fully polarimetric SAR imagery to demonstrate its effectiveness. Four test sites on the German North Sea coast were chosen, which represent typical surface compositions of different sediments, vegetation, and habitats, and of which a large amount of SAR is used for our analyses. Both Freeman-Durden and Cloude-Pottier polarimetric decomposition are utilized, and an additional descriptor called Double-Bounce Eigenvalue Relative Difference (DERD is introduced into the feature sets instead of the original polarimetric intensity channels. The classification is conducted following Random Forest theory, and the results are verified using ground truth data from field campaigns and an existing classification based on optical imagery. In addition, the use of Kennaugh elements for classification purposes is demonstrated using both fully and dual-polarization multi-frequency and multi-temporal SAR data. Our results show that the proposed classification scheme can be applied for the discrimination of muddy and sandy sediments using L-, C-, and X-band SAR images, while SAR imagery acquired at short wavelengths (C- and X-band can also be used to detect more detailed features such as bivalve beds on intertidal flats.

  4. Electromagnetically induced absorption via incoherent collisions

    International Nuclear Information System (INIS)

    Yang Xihua; Sheng Jiteng; Xiao Min

    2011-01-01

    We conduct theoretical studies on electromagnetically induced absorption via incoherent collisions in an inhomogeneously broadened ladder-type three-level system with the density-matrix approach. The effects of the collision-induced coherence decay rates as well as the probe laser field intensity on the probe field absorption are examined. It is shown that with the increase of the collisional decay rates in a moderate range, a narrow dip due to electromagnetically induced transparency superimposed on the Doppler-broadened absorption background can be turned into a narrow peak under the conditions that the probe field intensity is not very weak as compared to the pump field, which results from the enhancement of constructive interference and suppression of destructive interference between one-photon and multiphoton transition pathways. The physical origin of the collision-assisted electromagnetically induced absorption is analyzed with a power-series solution of the density-matrix equations.

  5. GROUND SUBSIDENCE ALONG SHANGHAI METRO LINE 6 BY PS-InSAR METHOD

    Directory of Open Access Journals (Sweden)

    J. Wu

    2018-04-01

    Full Text Available With the rapid development of urban economy, convenient, safe, and efficient urban rail transit has become the preferred method for people to travel. In order to ensure the safety and sustainable development of urban rail transit, the PS-InSAR technology with millimeter deformation measurement accuracy has been widely applied to monitor the deformation of urban rail transit. In this paper, 32 scenes of COSMO-SkyMed descending images and 23 scenes of Envisat ASAR images covering the Shanghai Metro Line 6 acquired from 2008 to 2010 are used to estimate the average deformation rate along line-of-sight (LOS direction by PS-InSAR method. The experimental results show that there are two main subsidence areas along the Shanghai Metro Line 6, which are located between Wuzhou Avenue Station to Wulian Road Station and West Gaoke Road Station to Gaoqing Road Station. Between Wuzhou Avenue Station and Wulian Road Station, the maximum displacement rate in the vertical direction of COSMO-SkyMed images is −9.92 mm/year, and the maximum displacement rate in the vertical direction of Envisat ASAR images is −8.53 mm/year. From the West Gaoke Road Station to the Gaoqing Road Station, the maximum displacement rate in the vertical direction of COSMO-SkyMed images is −15.53 mm/year, and the maximum displacement rate in the vertical direction of Envisat ASAR images is −17.9 mm/year. The results show that the ground deformation rates obtained by two SAR platforms with different wavelengths, different sensors and different incident angles have good consistence with each other, and also that of spirit leveling.

  6. Gastrointestinal absorption of uranium in man

    International Nuclear Information System (INIS)

    Larsen, R.P.; Orlandini, K.A.

    1984-01-01

    A method has been established for determining the fractional absorption of uranium directly in man. Measurements are made of the urinary excretion rates of uranium for individuals whose drinking water has a high 234 U to 238 U activity ratio and is the primary source of 234 U in their diets. For two individuals, the values obtained for the fractional absorption of 234 U were 0.004 and 0.006. The values obtained for the fractional absorption of 238 U, using a literature value for the 238 U intake from food, were 0.008 and 0.015. The present ICRP value is 0.20. 7 references, 1 table

  7. Intestinal Water Absorption Varies with Expected Dietary Water Load among Bats but Does Not Drive Paracellular Nutrient Absorption.

    Science.gov (United States)

    Price, Edwin R; Brun, Antonio; Gontero-Fourcade, Manuel; Fernández-Marinone, Guido; Cruz-Neto, Ariovaldo P; Karasov, William H; Caviedes-Vidal, Enrique

    2015-01-01

    Rapid absorption and elimination of dietary water should be particularly important to flying species and were predicted to vary with the water content of the natural diet. Additionally, high water absorption capacity was predicted to be associated with high paracellular nutrient absorption due to solvent drag. We compared the water absorption rates of sanguivorous, nectarivorous, frugivorous, and insectivorous bats in intestinal luminal perfusions. High water absorption rates were associated with high expected dietary water load but were not highly correlated with previously measured rates of (paracellular) arabinose clearance. In conjunction with these tests, we measured water absorption and the paracellular absorption of nutrients in the intestine and stomach of vampire bats using luminal perfusions to test the hypothesis that the unique elongated vampire stomach is a critical site of water absorption. Vampire bats' gastric water absorption was high compared to mice but not compared to their intestines. We therefore conclude that (1) dietary water content has influenced the evolution of intestinal water absorption capacity in bats, (2) solvent drag is not the only driver of paracellular nutrient absorption, and (3) the vampire stomach is a capable but not critical location for water absorption.

  8. River Delta Subsidence Measured with Interferometric Synthetic Aperture Radar (InSAR)

    Science.gov (United States)

    Higgins, Stephanie

    This thesis addresses the need for high-resolution subsidence maps of major world river deltas. Driven by a combination of rising water, sediment compaction, and reduced sediment supply due to damming and flood control, many deltas are sinking relative to sea level. A lack of data constraining rates and patterns of subsidence has made it difficult to determine the relative contributions of each factor in any given delta, however, or to assess whether the primary drivers of land subsidence are natural or anthropogenic. In recent years, Interferometric Synthetic Aperture Radar (InSAR) has emerged as a satellite-based technique that can map ground deformation with mm-scale accuracy over thousands of square kilometers. These maps could provide critical insight into the drivers of subsidence in deltas, but InSAR is not typically applied to non-urban delta areas due to the difficulties of performing the technique in wet, vegetated settings. This thesis addresses those difficulties and achieves high-resolution measurements of ground deformation in rural deltaic areas. Chapter 1 introduces the processes that drive relative sea level rise in river deltas and investigates open questions in delta subsidence research. Chapter 2 assesses the performance of InSAR in delta settings and reviews interferogram generation in the context of delta analysis, presenting delta-specific processing details and guiding interpretation in these challenging areas. Chapter 3 applies Differential (D-) InSAR to the coast of the Yellow River Delta in China. Results show that subsidence rates are as high as 250 mm/y due to groundwater extraction at aquaculture facilities, a rate that exceeds local and global average sea level rise by nearly two orders of magnitude and suggests a significant hazard for Asian megadeltas. Chapter 4 applies interferometric stacking and Small Baseline Subset (SBAS)-InSAR to the Ganges-Brahmaputra Delta, Bangladesh. Results show that stratigraphy controls subsidence in

  9. Uranium absorption study pile

    International Nuclear Information System (INIS)

    Raievski, V.; Sautiez, B.

    1959-01-01

    The report describes a pile designed to measure the absorption of fuel slugs. The pile is of graphite and comprises a central section composed of uranium rods in a regular lattice. RaBe sources and BF 3 counters are situated on either side of the center. A given uranium charge is compared with a specimen charge of about 560 kg, and the difference in absorption between the two noted. The sensitivity of the equipment will detect absorption variations of about a few ppm boron (10 -6 boron per gr. of uranium) or better. (author) [fr

  10. Ground Subsidence in the Beijing-Tianjin-Hebei Region from 1992 to 2014 Revealed by Multiple SAR Stacks

    Directory of Open Access Journals (Sweden)

    Yonghong Zhang

    2016-08-01

    Full Text Available The coordinated development of the Beijing-Tianjin-Hebei has become a national strategy with Beijing and Tianjin as twin engines driving the regional development. However, the Beijing-Tianjin-Hebei region has suffered dramatic ground subsidence during last two to three decades, mainly due to long-term groundwater withdrawal. Although, annual spirit leveling has been conducted routinely in some parts of Beijing and Tianjin, and InSAR technique has also been used to monitor ground subsidence in some local areas of the region, there is a lack of a complete survey of ground subsidence over the whole region. In this paper, we report a research on mapping ground subsidence in the Beijing-Tianjin-Hebei region over a long time span from 1992 to 2014. Three SAR datasets from four satellites are used: ERS-1/2 SAR images from 1992 to 2000, ENVISAT ASAR images from 2003 to 2010, and RADARSAT-2 images from 2012 to 2014. An improved multi-temporal InSAR method, namely “Multiple-master Coherent Target Small-Baseline InSAR” (MCTSB-InSAR, has been developed to process the datasets. A unique feature of MCTSB-InSAR is the adjustment process useful for wide area monitoring which provides an integrated solution for both calibration of InSAR-derived deformation and the harmonization of the deformation estimates from overlapping SAR frames. Three maps of the subsidence rate corresponding to the three periods over the wide Beijing-Tianjin-Hebei region are generated, with respective accuracy of 8.7 mm/year (1992–2000, 4.7 mm/year (2003–2010, and 5.4 mm/year (2012–2014 validated by more than 120 leveling measurements. The spatial-temporal characteristics of the development of ground subsidence in Beijing and Tianjin are analyzed. This research represents a first-ever effort on mapping ground subsidence over very large area and over long time span in China. The result is of significance to serve the decision-making on ground subsidence mitigation in the Beijing

  11. Land Cover Changes Detection in Polarimetric SAR Data Using Algebra, Similarity and Distance Based Methods

    Science.gov (United States)

    Najafi, A.; Hasanlou, M.; Akbari, V.

    2017-09-01

    Monitoring and surveillance changes around the world need powerful methods, so detection, visualization, and assessment of significant changes are essential for planning and management. Incorporating polarimetric SAR images due to interactions between electromagnetic waves and target and because of the high spatial resolution almost one meter can be used to study changes in the Earth's surface. Full polarized radar images comparing to single polarized radar images use amplitude and phase information of the surface in different available polarization (HH, HV, VH, and VV). This study is based on the decomposition of full polarized airborne UAVSAR images and integration of these features with algebra method involves Image Differencing (ID) and Image Ratio (IR) algorithms with the mathematical nature and distance-based method involves Canberra (CA) and Euclidean (ED) algorithms with measuring distance between corresponding vector and similarity-based method involves Taminoto (TA) and Kulczynski (KU) algorithms with dependence corresponding vector for change detecting purposes on two real PolSAR datasets. Assessment of incorporated methods is implemented using ground truth data and different criteria for evaluating such as overall accuracy (OA), area under ROC curve (AUC) and false alarms rate (FAR). The output results show that ID, IR, and CA have superiority to detect changes comparing to other implemented algorithms. Also, numerical results show that the highest performance in two datasets has OA more than 90%. In other assessment criteria, mention algorithms have low FAR and high AUC value indices to detect changes in PolSAR images.

  12. Role of fomites in SARS transmission during the largest hospital outbreak in Hong Kong.

    Science.gov (United States)

    Xiao, Shenglan; Li, Yuguo; Wong, Tze-Wai; Hui, David S C

    2017-01-01

    The epidemic of severe acute respiratory syndrome (SARS) had a significant effect on global society in the early 2000s and the potential of its resurgence exists. Studies on the modes of transmission of SARS are limited though a number of outbreak studies have revealed the possible airborne route. To develop more specific and effective control strategies, we conducted a detailed mechanism-based investigation that explored the role of fomite transmission in the well-known Ward 8A outbreak. We considered three hypothetical transmission routes, i.e., the long-range airborne, fomite and combined routes, in 1,744 scenarios with combinations of some important parameters. A multi-agent model was used to predict the infection risk distributions of the three hypothetical routes. Model selection was carried out for different scenarios to compare the distributions of infection risk with that of the reported attack rates and select the hypotheses with the best fitness. Our results reveal that under the assumed conditions, the SARS coronavirus was most possible to have spread via the combined long-range airborne and fomite routes, and that the fomite route played a non-negligible role in the transmission.

  13. Role of fomites in SARS transmission during the largest hospital outbreak in Hong Kong.

    Directory of Open Access Journals (Sweden)

    Shenglan Xiao

    Full Text Available The epidemic of severe acute respiratory syndrome (SARS had a significant effect on global society in the early 2000s and the potential of its resurgence exists. Studies on the modes of transmission of SARS are limited though a number of outbreak studies have revealed the possible airborne route. To develop more specific and effective control strategies, we conducted a detailed mechanism-based investigation that explored the role of fomite transmission in the well-known Ward 8A outbreak. We considered three hypothetical transmission routes, i.e., the long-range airborne, fomite and combined routes, in 1,744 scenarios with combinations of some important parameters. A multi-agent model was used to predict the infection risk distributions of the three hypothetical routes. Model selection was carried out for different scenarios to compare the distributions of infection risk with that of the reported attack rates and select the hypotheses with the best fitness. Our results reveal that under the assumed conditions, the SARS coronavirus was most possible to have spread via the combined long-range airborne and fomite routes, and that the fomite route played a non-negligible role in the transmission.

  14. Onboard Interferometric SAR Processor for the Ka-Band Radar Interferometer (KaRIn)

    Science.gov (United States)

    Esteban-Fernandez, Daniel; Rodriquez, Ernesto; Peral, Eva; Clark, Duane I.; Wu, Xiaoqing

    2011-01-01

    An interferometric synthetic aperture radar (SAR) onboard processor concept and algorithm has been developed for the Ka-band radar interferometer (KaRIn) instrument on the Surface and Ocean Topography (SWOT) mission. This is a mission- critical subsystem that will perform interferometric SAR processing and multi-look averaging over the oceans to decrease the data rate by three orders of magnitude, and therefore enable the downlink of the radar data to the ground. The onboard processor performs demodulation, range compression, coregistration, and re-sampling, and forms nine azimuth squinted beams. For each of them, an interferogram is generated, including common-band spectral filtering to improve correlation, followed by averaging to the final 1 1-km ground resolution pixel. The onboard processor has been prototyped on a custom FPGA-based cPCI board, which will be part of the radar s digital subsystem. The level of complexity of this technology, dictated by the implementation of interferometric SAR processing at high resolution, the extremely tight level of accuracy required, and its implementation on FPGAs are unprecedented at the time of this reporting for an onboard processor for flight applications.

  15. Role of the sar locus of Staphylococcus aureus in induction of endocarditis in rabbits.

    Science.gov (United States)

    Cheung, A L; Yeaman, M R; Sullam, P M; Witt, M D; Bayer, A S

    1994-05-01

    A regulatory locus on the Staphylococcus aureus chromosome, designated sar, is involved in the expression of cell wall proteins, some of which are potentially important in the pathogenesis of endocarditis. For instance, mutant 11D2 (sar::Tn917LTV1) was found to bind substantially less to matrix proteins (i.e., fibrinogen and fibronectin) than parent strain DB. Remarkably, these two strains did not differ in other phenotypes considered important in the initiation of endocarditis (e.g., binding to platelets and resistance to platelet-derived microbicidal proteins). The isogenic pair were compared for pathogenicity in a rabbit endocarditis model. There were significant differences in infectivity rates between the two strains (71 and 88% for DB versus 17 and 42% for mutant 11D2 at inocula of 10(3) and 10(4) CFU, respectively). In early adherence studies, parent DB adhered substantially better than the mutant to valvular vegetations at an inoculum of 10(6) CFU (P = 0.05). Southern blot analysis of colonies indicated that the location of the Tn917LTV1 insert in mutant 11D2 remained stable after animal passage. In vitro adherence assays revealed that mutant 11D2 was less adherent to cultured human endothelium than parent DB. These studies suggest that the sar locus is involved in the initial adherence of S. aureus to the fibrin-platelet-endothelium matrix on damaged valvular endothelium.

  16. Fast Vessel Detection in Gaofen-3 SAR Images with Ultrafine Strip-Map Mode.

    Science.gov (United States)

    Pan, Zongxu; Liu, Lei; Qiu, Xiaolan; Lei, Bin

    2017-07-05

    This study aims to detect vessels with lengths ranging from about 70 to 300 m, in Gaofen-3 (GF-3) SAR images with ultrafine strip-map (UFS) mode as fast as possible. Based on the analysis of the characteristics of vessels in GF-3 SAR imagery, an effective vessel detection method is proposed in this paper. Firstly, the iterative constant false alarm rate (CFAR) method is employed to detect the potential ship pixels. Secondly, the mean-shift operation is applied on each potential ship pixel to identify the candidate target region. During the mean-shift process, we maintain a selection matrix recording which pixels can be taken, and these pixels are called as the valid points of the candidate target. The l 1 norm regression is used to extract the principal axis and detect the valid points. Finally, two kinds of false alarms, the bright line and the azimuth ambiguity, are removed by comparing the valid area of the candidate target with a pre-defined value and computing the displacement between the true target and the corresponding replicas respectively. Experimental results on three GF-3 SAR images with UFS mode demonstrate the effectiveness and efficiency of the proposed method.

  17. Semi-Supervised Learning for Ill-Posed Polarimetric SAR Classification

    Directory of Open Access Journals (Sweden)

    Stefan Uhlmann

    2014-05-01

    Full Text Available In recent years, the interest in semi-supervised learning has increased, combining supervised and unsupervised learning approaches. This is especially valid for classification applications in remote sensing, while the data acquisition rate in current systems has become fairly large considering high- and very-high resolution data; yet on the other hand, the process of obtaining the ground truth data may be cumbersome for such large repositories. In this paper, we investigate the application of semi-supervised learning approaches and particularly focus on the small sample size problem. To that extend, we consider two basic unsupervised approaches by enlarging the initial labeled training set as well as an ensemble-based self-training method. We propose different strategies within self-training on how to select more reliable candidates from the pool of unlabeled samples to speed-up the learning process and to improve the classification performance of the underlying classifier ensemble. We evaluate the effectiveness of the proposed semi-supervised learning approach over polarimetric SAR data. Results show that the proposed self-training approach using an ensemble-based classifier that is initially trained over a small training set can achieve a similar performance level of a fully supervised learning approach where the training is performed over significantly larger labeled data. Considering the difficulties of the manual data labeling in such massive volumes of SAR repositories, this is indeed a promising accomplishment for semi-supervised SAR classification.

  18. Decreasing range resolution of a SAR image to permit correction of motion measurement errors beyond the SAR range resolution

    Science.gov (United States)

    Doerry, Armin W.; Heard, Freddie E.; Cordaro, J. Thomas

    2010-07-20

    Motion measurement errors that extend beyond the range resolution of a synthetic aperture radar (SAR) can be corrected by effectively decreasing the range resolution of the SAR in order to permit measurement of the error. Range profiles can be compared across the slow-time dimension of the input data in order to estimate the error. Once the error has been determined, appropriate frequency and phase correction can be applied to the uncompressed input data, after which range and azimuth compression can be performed to produce a desired SAR image.

  19. Survey of Volcanic Activity in Ecuador using L-band SAR.

    Science.gov (United States)

    Mothes, P.; Biggs, J.; Baker, S.; Hong, S.; Amelung, F.; Dixon, T.

    2008-12-01

    Ecuador has one of the highest densities of active volcanoes of any country, including 19 volcanoes with recorded Holocene eruptions. Many of these volcanoes are in remote areas with limited ground-based monitoring. InSAR is a satellite-based technique for detecting cm-scale ground displacements, such as those associated with the storage and transport of magma. InSAR has successfully been used for arc-scale surveys of volcanic activity in places such as the Aleutians and the Southern Andes. Previously, due to the high relief and dense vegetation, it has not been possible to carry out such a survey in Ecuador with existing C-band InSAR satellite images. Now that data are becoming available from the Japanese satellite ALOS, which operates at L-band, we are obtaining the first coherent interferograms for many of Ecuador's volcanoes. Preliminary results show that several volcanoes including Cotopaxi, and Guagua Pinchincha (which overlooks Quito) appear geodetically quiescent at the present time. One exception is Antisana, which presently has one of the highest rates of LP-SEISMIC activity in Ecuador. Preliminary InSAR observations shows signs of both inflation and deflation of Antisana. Two volcanoes have erupted within the time-scale of ALOS observation: Tungurahua and Reventador. At Tungurahua we see signs of deflation close to the summit, probably related to depresurrization of a shallow magma storage zone within the edifice. The only deformation we observe at Reventador is subsidence and is probably associated with compaction of a lava flow from 2005. Finally, we observe an extremely large subsidence signal in the Cayambe plain, probably associated with agricultural water extraction.

  20. Potential inundated coastal area estimation in Shanghai with multi-platform SAR and altimetry data

    Science.gov (United States)

    Ma, Guanyu; Yang, Tianliang; Zhao, Qing; Kubanek, Julia; Pepe, Antonio; Dong, Hongbin; Sun, Zhibin

    2017-09-01

    As global warming problem is becoming serious in recent decades, the global sea level is continuously rising. This will cause damages to the coastal deltas with the characteristics of low-lying land, dense population, and developed economy. Continuously reclamation costal intertidal and wetland areas are making Shanghai, the mega city of Yangtze River Delta, more vulnerable to sea level rise. In this paper, we investigate the land subsidence temporal evolution of patterns and processes on a stretch of muddy coast located between the Yangtze River Estuary and Hangzou Bay with differential synthetic aperture radar interferometry (DInSAR) analyses. By exploiting a set of 31 SAR images acquired by the ENVISAT/ASAR from February 2007 to May 2010 and a set of 48 SAR images acquired by the COSMO-SkyMed (CSK) sensors from December 2013 to March 2016, coherent point targets as long as land subsidence velocity maps and time series are identified by using the Small Baseline Subset (SBAS) algorithm. With the DInSAR constrained land subsidence model, we predict the land subsidence trend and the expected cumulative subsidence in 2020, 2025 and 2030. Meanwhile, we used altimetrydata and densely distributed in the coastal region are identified (EEMD) algorithm to obtain the average sea level rise rate in the East China Sea. With the land subsidence predictions, sea level rise predictions, and high-precision digital elevation model (DEM), we analyze the combined risk of land subsidence and sea level rise on the coastal areas of Shanghai. The potential inundated areas are mapped under different scenarios.

  1. NASA's NI-SAR Observing Strategy and Data Availability for Agricultural Monitoring and Assessment

    Science.gov (United States)

    Siqueira, P.; Dubayah, R.; Kellndorfer, J. M.; Saatchi, S. S.; Chapman, B. D.

    2014-12-01

    The monitoring and characterization of global crop development by remote sensing is a complex task, in part, because of the time varying nature of the target and the diversity of crop types and agricultural practices that vary worldwide. While some of these difficulties are overcome with the availability of national and market-derived resources (e.g. publication of crop statistics by the USDA and FAO), monitoring by remote sensing has the ability of augmenting those resources to better identify changes over time, and to provide timely assessments for the current year's production. Of the remote sensing techniques that are used for agricultural applications, optical observations of NDVI from Landsat, AVHRR, MODIS and similar sensors have historically provided the majority of data that is used by the community. In addition, radiometer and radar sensors, are often used for estimating soil moisture and structural information for these agricultural regions. The combination of these remote sensing datasets and national resources constitutes the state of the art for crop monitoring and yield forecasts. To help improve these crop monitoring efforts in the future, the joint NASA-ISRO SAR mission known as NI-SAR is being planned for launch in 2020, and will have L- and S-band fully polarimetric radar systems, a fourteen day repeat period, and a swath width on the order of several hundred kilometers. To address the needs of the science and applications communities that NI-SAR will support, the systems observing strategy is currently being planned such that data rate and the system configuration will address the needs of the community. In this presentation, a description of the NI-SAR system will be given along with the currently planned observing strategy and derived products that will be relevant to the overall GEOGLAM initiative.

  2. Building damage assessment from PolSAR data using texture parameters of statistical model

    Science.gov (United States)

    Li, Linlin; Liu, Xiuguo; Chen, Qihao; Yang, Shuai

    2018-04-01

    Accurate building damage assessment is essential in providing decision support for disaster relief and reconstruction. Polarimetric synthetic aperture radar (PolSAR) has become one of the most effective means of building damage assessment, due to its all-day/all-weather ability and richer backscatter information of targets. However, intact buildings that are not parallel to the SAR flight pass (termed oriented buildings) and collapsed buildings share similar scattering mechanisms, both of which are dominated by volume scattering. This characteristic always leads to misjudgments between assessments of collapsed buildings and oriented buildings from PolSAR data. Because the collapsed buildings and the intact buildings (whether oriented or parallel buildings) have different textures, a novel building damage assessment method is proposed in this study to address this problem by introducing texture parameters of statistical models. First, the logarithms of the estimated texture parameters of different statistical models are taken as a new texture feature to describe the collapse of the buildings. Second, the collapsed buildings and intact buildings are distinguished using an appropriate threshold. Then, the building blocks are classified into three levels based on the building block collapse rate. Moreover, this paper also discusses the capability for performing damage assessment using texture parameters from different statistical models or using different estimators. The RADARSAT-2 and ALOS-1 PolSAR images are used to present and analyze the performance of the proposed method. The results show that using the texture parameters avoids the problem of confusing collapsed and oriented buildings and improves the assessment accuracy. The results assessed by using the K/G0 distribution texture parameters estimated based on the second moment obtain the highest extraction accuracies. For the RADARSAT-2 and ALOS-1 data, the overall accuracy (OA) for these three types of

  3. A RAIL CENTRAL DISPLACEMENT METHOD ABOUT GB-SAR

    Directory of Open Access Journals (Sweden)

    J. Peng

    2016-06-01

    Full Text Available This paper presents a new method to correct rail errors of Ground Based Synthetic Aperture Radar (GB-SAR in the discontinue mode. Generally, “light positioning” is performed to mark the GB-SAR position in the dis-continuous observation mode. Usually we assume there is no difference between the marked position and the real installation position. But in fact, it is hard to keep the GB-SAR positions of two campaigns the same, so repositioning errors can’t be neglected. In order to solve this problem, we propose an algorithm to correct the rail error after analyzing the GB-SAR rail error geometry. Results of the simulation experiment and the real experiment of a landslide in Lvliang, Shanxi, China, show the proposed method achieves an mm-level precision, enabling the D-GBSAR mode to be used in engineering projects.

  4. The economic impact of SARS in Beijing, China.

    Science.gov (United States)

    Beutels, Philippe; Jia, Na; Zhou, Qing-Yi; Smith, Richard; Cao, Wu-Chun; de Vlas, Sake J

    2009-11-01

    To document the impact of the severe acute respiratory syndrome (SARS) outbreak in Beijing on indicators of social and economic activity. Associations between time series of daily and monthly SARS cases and deaths and volume of public train, airplane and cargo transport, tourism, household consumption patterns and gross domestic product growth in Beijing were investigated using the cross-correlation function. Significant correlation coefficients were found for all indicators except wholesale accounts and expenditures on necessities, with the most significant correlations occurring with a delay of 1 day to 1 month. Especially leisure activities, local and international transport and tourism were affected by SARS particularly in May 2003. Much of this consumption was merely postponed; but irrecoverable losses to the tourist sector alone were estimated at about US$ 1.4 bn, or 300 times the cost of treatment for SARS cases in Beijing.

  5. New military uses for synthetic aperture radar (SAR)

    Science.gov (United States)

    Reamer, Richard E.; Stockton, Wayne; Stromfors, Richard D.

    1993-02-01

    Loral Defense Systems-Arizona, holder of the original patent for the invention of Synthetic Aperture Radar (SAR), developed SAR to meet the military's need for an all-weather, day/night sensor that could produce high quality reconnaissance imagery in adverse weather and restricted visibility conditions. These features, and the ability to image large areas with fine resolution in a relatively short period of time make this sensor useful for many military applications. To date, however, SARs for military use have been hampered by the fact that they've been large, complex, and expensive. Additionally, they have been mounted on special purpose, single mission aircraft which are costly to operate. That situation has changed. A small, modular SAR, called Miniature Synthetic Aperture Radar (MSAR) developed by Loral can be mounted with relative ease on Unmanned Aerial Vehicles (UAV) or on multi-mission aircraft such as the F-16, F/A-18, or on the F-14.

  6. Modeling amplitude SAR image with the Cauchy-Rayleigh mixture

    Science.gov (United States)

    Peng, Qiangqiang; Du, Qingyu; Yao, Yinwei; Huang, Huang

    2017-10-01

    In this paper, we introduce a novel mixture model of the SAR amplitude image, which is proposed as an approximation to the heavy-tailed Rayleigh model. The limitation of the heavy-tailed Rayleigh model in SAR image application is discussed. We also present an expectation-maximization (EM) algorithm based parameter estimation method for the Cauchy-Rayleigh mixture. We test the new model on some simulated data in order to confirm that is appropriate to the heavy-tailed Rayleigh model. The performance is evaluated by some statistic values (cumulative square errors (CSE) 0.99 and Kolmogorov-Smirnov distance (K-S) the performance of the proposed mixture model is tested on some real SAR images and compared with other models, including the heavy-tailed Rayleigh and Nakagami mixture models. The result indicates that the proposed model can be an optional statistical model for amplitude SAR images.

  7. Stellwagen Bank National Marine Sanctuary - Synthetic Aperture Radar (SAR) Imagery

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This geodatabase contains Synthetic Aperture Radar images (SAR), which consist of a fine resolution (12.5-50m), two-dimensional radar backscatter map of the...

  8. Change detection in polarimetric SAR data over several time points

    DEFF Research Database (Denmark)

    Conradsen, Knut; Nielsen, Allan Aasbjerg; Skriver, Henning

    2014-01-01

    A test statistic for the equality of several variance-covariance matrices following the complex Wishart distribution is introduced. The test statistic is applied successfully to detect change in C-band EMISAR polarimetric SAR data over four time points....

  9. RAMP AMM-1 SAR Image Mosaic of Antarctica

    Data.gov (United States)

    National Aeronautics and Space Administration — In 1997, the Canadian RADARSAT-1 satellite was rotated in orbit so that its Synthetic Aperture Radar (SAR) antenna looked south towards Antarctica. This permitted...

  10. Reconstruction of interrupted SAR imagery for persistent surveillance change detection

    Science.gov (United States)

    Stojanovic, Ivana; Karl, W. C.; Novak, Les

    2012-05-01

    In this paper we apply a sparse signal recovery technique for synthetic aperture radar (SAR) image formation from interrupted phase history data. Timeline constraints imposed on multi-function modern radars result in interrupted SAR data collection, which in turn leads to corrupted imagery that degrades reliable change detection. In this paper we extrapolate the missing data by applying the basis pursuit denoising algorithm (BPDN) in the image formation step, effectively, modeling the SAR scene as sparse. We investigate the effects of regular and random interruptions on the SAR point spread function (PSF), as well as on the quality of both coherent (CCD) and non-coherent (NCCD) change detection. We contrast the sparse reconstruction to the matched filter (MF) method, implemented via Fourier processing with missing data set to zero. To illustrate the capabilities of the gap-filling sparse reconstruction algorithm, we evaluate change detection performance using a pair of images from the GOTCHA data set.

  11. Learning a Dilated Residual Network for SAR Image Despeckling

    Science.gov (United States)

    Zhang, Qiang; Yuan, Qiangqiang; Li, Jie; Yang, Zhen; Ma, Xiaoshuang

    2018-01-01

    In this paper, to break the limit of the traditional linear models for synthetic aperture radar (SAR) image despeckling, we propose a novel deep learning approach by learning a non-linear end-to-end mapping between the noisy and clean SAR images with a dilated residual network (SAR-DRN). SAR-DRN is based on dilated convolutions, which can both enlarge the receptive field and maintain the filter size and layer depth with a lightweight structure. In addition, skip connections and residual learning strategy are added to the despeckling model to maintain the image details and reduce the vanishing gradient problem. Compared with the traditional despeckling methods, the proposed method shows superior performance over the state-of-the-art methods on both quantitative and visual assessments, especially for strong speckle noise.

  12. Sliding Spotlight Mode Imaging with GF-3 Spaceborne SAR Sensor

    Directory of Open Access Journals (Sweden)

    Qingjun Zhang

    2017-12-01

    Full Text Available Synthetic aperture radar (SAR sliding spotlight work mode can achieve high resolutions and wide swath (HRWS simultaneously by steering the radar antenna beam. This paper aims to obtain well focused images using sliding spotlight mode with the Chinese Gaofen-3 SAR sensor. We proposed an integrated imaging scheme with sliding spotlight echoes. In the imaging scheme, the two-step approach is applied to the spaceborne sliding spotlight SAR imaging algorithm, followed by the Doppler parameter estimation algorithm. The azimuth spectral folding phenomenon is overcome by the two-step approach. The results demonstrate a high Doppler parameter estimation accuracy. The proposed imaging process is accurate and highly efficient for sliding spotlight SAR mode.

  13. An Objective Evaluation of Four SAR Image Segmentation Algorithms

    National Research Council Canada - National Science Library

    Gregga, Jason

    2001-01-01

    .... A key step towards automated SAR image analysis is image segmentation. There are many segmentation algorithms, but they have not been tested on a common set of images, and there are no standard test methods...

  14. Learning a Dilated Residual Network for SAR Image Despeckling

    Directory of Open Access Journals (Sweden)

    Qiang Zhang

    2018-01-01

    Full Text Available In this paper, to break the limit of the traditional linear models for synthetic aperture radar (SAR image despeckling, we propose a novel deep learning approach by learning a non-linear end-to-end mapping between the noisy and clean SAR images with a dilated residual network (SAR-DRN. SAR-DRN is based on dilated convolutions, which can both enlarge the receptive field and maintain the filter size and layer depth with a lightweight structure. In addition, skip connections and a residual learning strategy are added to the despeckling model to maintain the image details and reduce the vanishing gradient problem. Compared with the traditional despeckling methods, the proposed method shows a superior performance over the state-of-the-art methods in both quantitative and visual assessments, especially for strong speckle noise.

  15. Wavelet Filter Banks for Super-Resolution SAR Imaging

    Science.gov (United States)

    Sheybani, Ehsan O.; Deshpande, Manohar; Memarsadeghi, Nargess

    2011-01-01

    This paper discusses Innovative wavelet-based filter banks designed to enhance the analysis of super resolution Synthetic Aperture Radar (SAR) images using parametric spectral methods and signal classification algorithms, SAR finds applications In many of NASA's earth science fields such as deformation, ecosystem structure, and dynamics of Ice, snow and cold land processes, and surface water and ocean topography. Traditionally, standard methods such as Fast-Fourier Transform (FFT) and Inverse Fast-Fourier Transform (IFFT) have been used to extract Images from SAR radar data, Due to non-parametric features of these methods and their resolution limitations and observation time dependence, use of spectral estimation and signal pre- and post-processing techniques based on wavelets to process SAR radar data has been proposed. Multi-resolution wavelet transforms and advanced spectral estimation techniques have proven to offer efficient solutions to this problem.

  16. A beamforming algorithm for bistatic SAR image formation

    Science.gov (United States)

    Jakowatz, Charles V., Jr.; Wahl, Daniel E.; Yocky, David A.

    2010-04-01

    Beamforming is a methodology for collection-mode-independent SAR image formation. It is essentially equivalent to backprojection. The authors have in previous papers developed this idea and discussed the advantages and disadvantages of the approach to monostatic SAR image formation vis-à-vis the more standard and time-tested polar formatting algorithm (PFA). In this paper we show that beamforming for bistatic SAR imaging leads again to a very simple image formation algorithm that requires a minimal number of lines of code and that allows the image to be directly formed onto a three-dimensional surface model, thus automatically creating an orthorectified image. The same disadvantage of beamforming applied to monostatic SAR imaging applies to the bistatic case, however, in that the execution time for the beamforming algorithm is quite long compared to that of PFA. Fast versions of beamforming do exist to help alleviate this issue. Results of image reconstructions from phase history data are presented.

  17. A Stepped Frequency CW SAR for Lightweight UAV Operation

    National Research Council Canada - National Science Library

    Morrison, Keith

    2005-01-01

    A stepped-frequency continuous wave (SF-CW) synthetic aperture radar (SAR), with frequency-agile waveforms and real-time intelligent signal processing algorithms, is proposed for operation from a lightweight UAV platform...

  18. Genome organization of the SARS-CoV

    DEFF Research Database (Denmark)

    Xu, Jing; Hu, Jianfei; Wang, Jing

    2003-01-01

    Annotation of the genome sequence of the SARS-CoV (severe acute respiratory syndrome-associated coronavirus) is indispensable to understand its evolution and pathogenesis. We have performed a full annotation of the SARS-CoV genome sequences by using annotation programs publicly available or devel......Annotation of the genome sequence of the SARS-CoV (severe acute respiratory syndrome-associated coronavirus) is indispensable to understand its evolution and pathogenesis. We have performed a full annotation of the SARS-CoV genome sequences by using annotation programs publicly available...... regions. The analysis of TRS supports the minus strand extending transcription mechanism of coronavirus. The SNP analysis of different isolates reveals that mutations of the sequences do not affect the prediction results of ORFs. Udgivelsesdato: 2003-Aug...

  19. Mining Land Subsidence Monitoring Using SENTINEL-1 SAR Data

    Science.gov (United States)

    Yuan, W.; Wang, Q.; Fan, J.; Li, H.

    2017-09-01

    In this paper, DInSAR technique was used to monitor land subsidence in mining area. The study area was selected in the coal mine area located in Yuanbaoshan District, Chifeng City, and Sentinel-1 data were used to carry out DInSAR techniqu. We analyzed the interferometric results by Sentinel-1 data from December 2015 to May 2016. Through the comparison of the results of DInSAR technique and the location of the mine on the optical images, it is shown that DInSAR technique can be used to effectively monitor the land subsidence caused by underground mining, and it is an effective tool for law enforcement of over-mining.

  20. Massachusetts Bay - Internal wave packets digitized from SAR imagery

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This feature class contains internal wave packets digitized from SAR imagery at 1:350,000 scale in Massachusetts Bay. Internal waves are nonsinusoidal waves that...