Impact of toothbrushing with a dentifrice containing calcium peroxide on enamel color and roughness.

Science.gov (United States)

Feitosa, Diala Aretha de Sousa; Borges, Boniek Castillo Dutra; Pinheiro, Fabio Henrique de Sa Leitao; Duarte, Rosangela Marques; Araujo, Renato Evangelista de; Braz, Rodivan; Santos, Maria Carmo Moreira da Silva; Montes, Marcos Antonio Japiassu Resende

2015-01-01

This in vitro study sought to evaluate both the bleaching potential and changes to average surface roughness (Ra) of enamel after brushing with a dentifrice. Fifty-four enamel specimens (4 x 4 x 2 mm) were divided into 3 groups (n = 18) and treated with 1 of 3 dentifrices: 1 with calcium peroxide, and 2 without. The samples were submitted to 20,000 brushing cycles. Color and Ra were measured before and after brushing. Although the Ra increased in all groups after brushing, only the dentifrice containing calcium peroxide resulted in an increase in reflectance.

In vitro study on tooth enamel lesions related to whitening dentifrice.

Science.gov (United States)

de Araújo, Danilo Barral; Silva, Luciana Rodrigues; Campos, Elisângela de Jesus; Correia de Araújo, Roberto Paulo

2011-01-01

The tooth whitening substances for extrinsic use that are available in Brazil contain hydrogen peroxide or carbamide peroxide. Several studies have attributed the appearance of lesions in the enamel morphology, including hypersensitivity, to these substances. Such lesions justify fluoride therapy and application of infrared lasers, among other procedures. However, there is no consensus among researchers regarding the relevance of the severity of lesions detected on the tooth surface. The present study was carried out with an aim of evaluating in vitro the effects of the hydrogen peroxide, carbamide peroxide and sodium bicarbonate contained in dentifrice formulations, on human tooth enamel. After darkening process in laboratory, human premolars were brushed using dentifrice containing the two whitening substances (Rembrandt - carbamide peroxide and Mentadent - hydrogen peroxide) and the abrasive product (Colgate - sodium bicarbonate). The degree of specimen staining before and after this procedure was determined using spectrophotometry. Scanning electron microscopy (SEM) was used to obtain images, which were analyzed to show the nature of the lesions that appeared on the enamel surface. The effectiveness of the whitening caused by hydrogen peroxide and carbamide peroxide and the abrasion caused by bicarbonate were confirmed, given that the treated test pieces returned to their original coloration. Based on SEM, evaluation of the enamel surfaces subjected to the test products showed that different types of morphologic lesions of varying severity appeared. Whitening dentifrice containing hydrogen peroxide and carbamide peroxide produced lesions on the enamel surface such that the greatest sequelae were associated with exposure to hydrogen peroxide.

In vitro study on tooth enamel lesions related to whitening dentifrice

Directory of Open Access Journals (Sweden)

Danilo Barral de Araújo

2011-01-01

Full Text Available Background: The tooth whitening substances for extrinsic use that are available in Brazil contain hydrogen peroxide or carbamide peroxide. Several studies have attributed the appearance of lesions in the enamel morphology, including hypersensitivity, to these substances. Such lesions justify fluoride therapy and application of infrared lasers, among other procedures. However, there is no consensus among researchers regarding the relevance of the severity of lesions detected on the tooth surface. Objectives: The present study was carried out with an aim of evaluating in vitro the effects of the hydrogen peroxide, carbamide peroxide and sodium bicarbonate contained in dentifrice formulations, on human tooth enamel. Materials and Methods: After darkening process in laboratory, human premolars were brushed using dentifrice containing the two whitening substances (Rembrandt - carbamide peroxide and Mentadent - hydrogen peroxide and the abrasive product (Colgate - sodium bicarbonate. The degree of specimen staining before and after this procedure was determined using spectrophotometry. Scanning electron microscopy (SEM was used to obtain images, which were analyzed to show the nature of the lesions that appeared on the enamel surface. Results: The effectiveness of the whitening caused by hydrogen peroxide and carbamide peroxide and the abrasion caused by bicarbonate were confirmed, given that the treated test pieces returned to their original coloration. Based on SEM, evaluation of the enamel surfaces subjected to the test products showed that different types of morphologic lesions of varying severity appeared. Conclusions: Whitening dentifrice containing hydrogen peroxide and carbamide peroxide produced lesions on the enamel surface such that the greatest sequelae were associated with exposure to hydrogen peroxide.

A comparison of intraoral antimicrobial effects of stabilized stannous fluoride dentifrice, baking soda/peroxide dentifrice, conventional NaF dentifrice and essential oil mouthrinse.

Science.gov (United States)

Bacca, L A; Leusch, M; Lanzalaco, A C; Macksood, D; Bouwsma, O J; Shaffer, J B; Howard-Nordan, K S; Knippenberg, S H; Kreutzjans, M K; Miller, J M; Poore, C L; Sunberg, R J; Vastola, K A; Becus, M; Bartizek, R D; Block, R P; Briner, W W; White, D J

1997-01-01

The intraoral antimicrobial activity of four commercial oral products-conventional NaF dentifrice (Crest), baking soda/peroxide/NaF dentifrice (Mentadent), essential oil mouthrinse (Listerine) and SnF2 dentifrice (Crest Plus Gum Care)-have been compared in three test regimens. Formulations were compared for their ability to suppress the regrowth and apical extension of dental plaque following toothbrushing during thirty hours of non-brushing where products were used as oral rinses (30-hour plaque regrowth model). Formulations were also compared for their ability to suppress the colony-forming units (cfu) of facultative anaerobic bacteria sampled from buccal gingival surfaces following use (Gingival Surface Microbial Index-GSMI model). Lastly, formulations were compared for effects in suppressing the glycolytic metabolic activity and regrowth activity of in vivo-treated dental plaques sampled at various periods following topical use and incubated under controlled ex vivo conditions (Plaque Glycolysis and Regrowth-PGRM model). In thirty-hour plaque regrowth testing, the rank ordered antimicrobial efficacy of formulations followed SnF2 > essential oils > NaF = water = baking soda/peroxide. In GSMI testing, all formulations were shown to suppress the cfu of facultative anaerobic bacteria relative to baseline, although SnF2 treatment was observed to reduce bacterial levels to a significantly greater degree than NaF dentifrice or baking soda/peroxide dentifrice up to two hours following brushing. In PGRM testing, the SnF2 dentifrice provided significant inhibition of bacterial metabolism and regrowth following topical application when compared with the NaF dentifrice as control. The baking soda/peroxide dentifrice provided no reduction in either bacterial metabolism or regrowth in PGRM. Previous studies had demonstrated modest effects for essential oil rinse in reducing PGRM plaque regrowth, with no effects for this treatment on plaque metabolism. Overall, these results

Effect of denture cleaning on abrasion resistance and surface topography of polymerized CAD CAM acrylic resin denture base.

Science.gov (United States)

Shinawi, Lana Ahmed

2017-05-01

The application of computer-aided design computer-aided manufacturing (CAD CAM) technology in the fabrication of complete dentures, offers numerous advantages as it provides optimum fit and eliminates polymerization shrinkage of the acrylic base. Additionally, the porosity and surface roughness of CAD CAM resins is less compared to conventionally processed resins which leads to a decrease in the adhesion of bacteria on the denture base, which is associated with many conditions including halitosis and aspiration pneumonia in elderly denture wearers. To evaluate the influence of tooth brushing with dentifrices on CAD CAM resin blocks in terms of abrasion resistance, surface roughness and scanning electron photomicrography. This experimental study was carried out at the Faculty of Dentistry of King Abdulaziz University during 2016. A total of 40 rectangular shaped polymerized CAD CAM resin samples were subjected to 40.000 and 60.000 brushing strokes under a 200-gram vertical load simulating three years of tooth brushing strokes using commercially available denture cleaning dentifrice. Data were analyzed by SPSS version 20, using descriptive statistics and ANOVA. ANOVA test revealed a statistical significant weight loss of CAD CAM acrylic resin denture base specimens following 40.000 and 60.000 brushing strokes as well as a statistical significant change (p=0.0.5) in the surface roughness following brushing. The CAD CAM resin samples SEM baseline imaging revealed a relatively smooth homogenous surface, but following 40,000 and 60,000 brushing strokes, imaging displayed the presence of small scratches on the surface. CAD CAM resin displayed a homogenous surface initially with low surface roughness that was significantly affected following simulating three years of manual brushing, but despite the significant weight loss, the findings are within the clinically acceptable limits.

Effect of baking soda in dentifrices on plaque removal.

Science.gov (United States)

Myneni, Srinivas R

2017-11-01

The prevention of dental caries and periodontal diseases targets control of dental plaque biofilm. In this context, chemical agents could represent a valuable complement to mechanical plaque control by reducing and controlling biofilm formation. The literature on the effectiveness of different dentifrices has not, however, been carefully categorized. A lack of consensus exists among dental professionals on a recommendation for a universal dentifrice for plaque control. The authors reviewed the scientific data on the different properties of sodium bicarbonate (baking soda)-containing dentifrices and their effectiveness in plaque removal. The results of the literature search show that baking soda-containing dentifrices are ideal candidates to be considered as a universal dentifrice because baking soda is inexpensive, abundant in supply, highly biocompatible, exhibits specific antibacterial properties to oral microorganisms, has low abrasivity, and is effective in plaque biofilm removal. Although some patients may benefit from desensitizing or high fluoride-containing dentifrices, those with routine needs may find using dentifrices containing baking soda and fluoride effective. Baking soda and fluoride dentifrices, therefore, may perhaps be considered as a criterion standard for patients with routine oral hygiene needs. Copyright © 2017 American Dental Association. Published by Elsevier Inc. All rights reserved.

Effect of power toothbrushing on simulated wear of dental cement margins.

Science.gov (United States)

Black, Marsha A; Bayne, Stephen C; Peterson, Charlotte A

2007-01-01

Power toothbrushes (PTBs), in combination with abrasive dentifrices, may encourage wear of dental cements at crown margins. The objective of this in vitro simulation was to control the clinical variables associated with PTB use and measure the potential side effects of PTBs with mild and abrasive dentifrices. Four PTBs ( Braun-Oral-B-Professional Care at 150 g brushing force, Sonicare-Elite at 90 g, Colgate-Actibrush at 200 g and Crest-Spinbrush-Pro at 250 g) and 2 dentifrices mixed 1:1 with tap water (Mild= Colgate-Total, Colgate-Palmolive; Abrasive= Close-up, Chesebrough-Ponds) versus tap water alone (control) were used to abrade 2 cements (Fleck's Mizzy Zinc Phosphate [ZP]; 3M-ESPE Unicem universal cement [UC]) using cement-filled slots (160 m wide) cut into wear-resistant ceramic blocks. A custom fixture controlled PTB/block alignment, PTB loads, and other testing variables. Wear was measured (3 profilometer traces/slot, 5 slots/block/group, baseline to 5-year differences) and analyzed (3-way ANOVA, p PTBs and both dentifrices. Brushing with water showed no effects (pPTBs. Pooled 5y-wear levels for ZP for both dentifrices approximately 21 microm /5y) were similar to values for current-day posterior composite materials. Combinations of PTBs with mild and abrasive dentifrices produced significant wear with ZP but not UC; thus, resin-composite cements seem to represent a better choice for wear resistance.

Effects of mechanical cleaning by manual brushing and abrasive blasting on lime render coatings on Architectural Heritage

Directory of Open Access Journals (Sweden)

Iglesias-Campos, M. A.

2014-12-01

Full Text Available This research studies the effects of mechanical cleaning by brushing and by abrasive blasting on the lime render coating of a façade. After analysing the properties of the material, the deposits to be removed and their possible influence on the treatment, different cleaning tests were made by manual brushing and by blasting with three varieties of abrasives at 45° and 75° angles, keeping the other parameters constant. Taking the restorer’s perspective as a starting point, and in order to fulfil the practical requirements of an intervention, tests were evaluated with macro-photography, USB digital microscope and stereomicroscope with 3D visualization and measurement. From the results can be concluded that abrasives with low friability and greater grain size than the space between mortar aggregates blasted at a 75° angle reduce the differential erosion compared to other abrasives; although manual brushing has less impact on the surface.En este trabajo se estudian los efectos de las limpiezas mecánicas con cepillado y con proyección de abrasivos sobre un revestimiento exterior de cal. Tras documentar las propiedades del material, de los depósitos superficiales y de su posible influencia en el tratamiento, se realizaron diferentes catas de limpieza con cepillado manual y con proyección de tres abrasivos con ángulos de 45° y 75° manteniendo constantes el resto de parámetros. Partiendo de la visión del conservador-restaurador y de un carácter práctico según las necesidades reales de intervención, los ensayos se evaluaron con macrofotografía, microscopio digital USB y microscopio estereoscópico con visualización y medición en 3D. De los resultados se determina que los abrasivos de baja friabilidad y granulometría mayor que el espacio entre los áridos del mortero proyectados con un ángulo de 75° reducen la erosión diferencial en comparación a otros abrasivos, aunque el cepillado manual altera menos la superficie.

Evaluation of a dentifrice containing 8% arginine, calcium carbonate, and sodium monofluorophosphate to repair acid-softened enamel using an intra-oral remineralization model.

Science.gov (United States)

Sullivan, R; Rege, A; Corby, P; Klaczany, G; Allen, K; Hershkowitz, D; Goldder, B; Wolff, M

2014-01-01

An intra-oral remineralization study was conducted to compare the ability of a dentifrice containing 8% arginine and calcium carbonate (Pro-Argin Technology), and 1450 ppm fluoride as sodium monofluorophosphate (MFP) to remineralize acid-softened bovine enamel specimens compared to a silica-based dentifrice with 1450 ppm fluoride as MFP. The intra-oral clinical study employed a double blind, two-treatment, crossover design, and used an upper palatal retainer to expose the enamel specimens to the oral environment during product use and periods of remineralization. The retainer was designed to house three partially demineralized bovine enamel samples. The study population was comprised of 30 adults, ages 18 to 70 years. The study consisted of two treatment phases with a washout period lasting seven (+/- three) days preceding each treatment phase. A silica-based dentifrice without fluoride was used during the washout period. The Test Dentifrice used in this study contained 8% arginine, calcium carbonate, and 1450 ppm fluoride as sodium monofluorophosphate (MFP). The Control Dentifrice was silica-based and contained 1450 ppm fluoride as MFP. The treatment period consisted of a three-day lead-in period with the assigned product. The panelists brushed two times per day during the three-day lead-in period with the assigned product. On the fourth day, the panelists began brushing with the assigned product with the retainer in their mouth. The panelists brushed for one minute, followed by a one-minute swish with the slurry and a rinse with 15 ml of water in the morning, in the afternoon, and night with the retainer in the mouth. The panelists brushed only their teeth and not the specimens directly. Changes in mineral content before and after treatment were measured using a Knoop microhardness tester. The results of the study showed that percent remineralization values for the Test Dentifrice and Control Dentifrice were 14.99% and 8.66%, respectively. A statistical analysis

Profilometric analysis of two composite resins' surface repolished after tooth brush abrasion with three polishing systems.

Science.gov (United States)

Uppal, Mudit; Ganesh, Arathi; Balagopal, Suresh; Kaur, Gurleen

2013-07-01

To evaluate the effect of three polishing protocols that could be implemented at recall on the surface roughness of two direct esthetic restorative materials. Specimens (n = 40) measuring 8 mm (length) × 5 mm (width) × 4 mm (height) were fabricated in an acrylic mold using two light-cured resin-based materials (microfilled composite and microhybrid composite). After photopolymerization, all specimens were finished and polished with one of three polishing protocols (Enhance, One Gloss, and Sof-Lex polishing systems). The average surface roughness of each treated specimen was determined using 3D optical profilometer. Next all specimens were brushed 60,000 times with nylon bristles at 7200 rpm using crosshead brushing device with equal parts of toothpaste and water used as abrasive medium. The surface roughness of each specimen was measured after brushing followed by repolishing with one of three polishing protocols, and then, the final surface roughness values were determined. The data were analyzed using one-way and two-factor analysis of variance (ANOVA) and Tukey's honestly significant difference (HSD). Significant difference (P < 0.05) in surface roughness was observed. Simulated brushing following initial polishing procedure significantly roughened the surface of restorative material (P < 0.05). Polishing protocols can be used to restore a smooth surface on esthetic restorative materials following simulated tooth brushing.

A comparative clinical study investigating the efficacy of a test dentifrice containing 8% strontium acetate and 1040 ppm sodium fluoride versus a marketed control dentifrice containing 8% arginine, calcium carbonate, and 1450 ppm sodium monofluorophosphate in reducing dentinal hypersensitivity.

Science.gov (United States)

Hughes, Nathan; Mason, Stephen; Jeffery, Peter; Welton, Helen; Tobin, Maira; O'Shea, Caoimhe; Browne, Mairead

2010-01-01

The objective of this clinical study was to evaluate and compare the efficacy in reducing dentin hypersensitivity of an 8% strontium acetate, 1040 ppm sodium fluoride dentifrice to a marketed control 8% arginine, calcium carbonate, 1450 ppm sodium monofluorophosphate dentifrice after twice-daily brushing for two, four, and eight weeks. This was a randomized, examiner-blind, two-arm parallel group, eight-week longitudinal clinical study with seventy-nine subjects, stratified based on baseline tooth sensitivity (Schiff score, Yeaple). Subjects brushed with either an 8% strontium acetate-based dentifrice or a marketed 8% arginine calcium carbonate dentifrice twice daily for approximately one minute. At screening, baseline, weeks two, four, and eight, subjects' tooth sensitivity was determined through both evaporative (Schiff and Visual Analogue Scale [VAS]) and tactile stimuli (Yeaple probe). Subject assessments using each stimulus were performed by the same examiner throughout the study. Seventy-seven subjects completed this clinical study. Both subject groups exhibited significant cumulative reductions from baseline to Days 14, 28, and 56 in dentin hypersensitivity as measured by Schiff, Yeaple, and VAS (for the 8% strontium acetate group, p carbonate group, p = 0.0031 for Yeaple at Day 14, p = 0.0015 for VAS at Day 14, and p 0.05) were observed between treatments for any of the time points and measures except for tactile sensitivity at Day 56, for which the 8% strontium acetate-based dentifrice was statistically superior (p = 0.0391) to the control 8% arginine calcium carbonate dentifrice. The 8% strontium acetate, 1040 ppm sodium fluoride dentifrice provided significant reductions in dentin hypersensitivity (p carbonate dentifrice showed no significant differences (p > 0.05) apart from tactile (Yeaple) sensitivity at week 8, where the 8% strontium acetate-based dentifrice showed significant improvement over the control (p = 0.0391).

A Comparative Evaluation of the Efficacy of Two Novel Desensitising Dentifrices

Science.gov (United States)

Barlow, Ashley P.; He, Jane; Tian, Cindy; Jeffery, Peter; Mason, Stephen C.; Tai, Bao-Jun; Jiang, Han; Rees, Gareth D.; Du, Min Quan

2012-01-01

A comparison of the desensitising efficacy of two commercially available dentifrices with different modes of action was conducted in a randomised, examiner-blind, two-arm, parallel group, 8-week, longitudinal clinical study. Dentifrice A, (Sensodyne Multi Action Iso-Active), contained 50000 ppm KNO3 and 1450 ppm fluoride as NaF. Dentifrice B, Colgate Sensitive Pro-Relief, contained a combination of 80000 ppm arginine, bicarbonate, calcium carbonate, and 1450 ppm fluorine as NaMFP. Subjects (N = 110), stratified into two groups (N = 55), brushed twice-daily for 60 s, over an 8-week period. Sensitivity status, compliance, and safety were determined at 1, 2, 4, and 8 weeks. A fixed-effects ANCOVA statistical model was applied to the Intent-To-Treat population using a two-sided 5% significance level. After 8 weeks, the treatment groups using Dentifrice A and Dentifrice B exhibited mean reductions from baseline of 49% and 45% in air sensitivity visual analogue scale (VAS) score, 61% (both) in examiner-based Schiff Sensitivity score, and clinically significant reductions in tactile pain threshold; all reductions were statistically significant (P < 0.0001). Both treatment groups also exhibited significant reductions across all sensitivity measures at 1, 2, and 4 weeks (P ≤ 0.0059, Dentifrice A; P ≤ 0.0137, Dentifrice B). PMID:23304149

A Comparative Evaluation of the Efficacy of Two Novel Desensitising Dentifrices

Directory of Open Access Journals (Sweden)

Ashley P. Barlow

2012-01-01

Full Text Available A comparison of the desensitising efficacy of two commercially available dentifrices with different modes of action was conducted in a randomised, examiner-blind, two-arm, parallel group, 8-week, longitudinal clinical study. Dentifrice A, (Sensodyne Multi Action Iso-Active, contained 50000 ppm KNO3 and 1450 ppm fluoride as NaF. Dentifrice B, Colgate Sensitive Pro-Relief, contained a combination of 80000 ppm arginine, bicarbonate, calcium carbonate, and 1450 ppm fluorine as NaMFP. Subjects (N=110, stratified into two groups (N=55, brushed twice-daily for 60 s, over an 8-week period. Sensitivity status, compliance, and safety were determined at 1, 2, 4, and 8 weeks. A fixed-effects ANCOVA statistical model was applied to the Intent-To-Treat population using a two-sided 5% significance level. After 8 weeks, the treatment groups using Dentifrice A and Dentifrice B exhibited mean reductions from baseline of 49% and 45% in air sensitivity visual analogue scale (VAS score, 61% (both in examiner-based Schiff Sensitivity score, and clinically significant reductions in tactile pain threshold; all reductions were statistically significant (P<0.0001. Both treatment groups also exhibited significant reductions across all sensitivity measures at 1, 2, and 4 weeks (P≤0.0059, Dentifrice A; P≤0.0137, Dentifrice B.

[Historical investigation of dentifrice in China].

Science.gov (United States)

Kubo, M; Song, Q; Tang, F

2001-01-01

A herbal literature survey was carried out on data concerning historical pharmacognostical changes of "dentifrice" in China and how diseases of the teeth and gums had been treated there in ancient times. It had been considered to be a matter of utmost importance that to prevent teeth from decaying, only the brushing of teeth with a toothbrush was necessary. Over time, various tooth agents have been found to treat oral diseases the teeth and gums. Glycyrrhizae Radix, Ginseng Radix, Scutellariae Radix, Menthae Herbal, and salt were widely used materials. Investigations from all approaches are being carried out to develop remedies for oral diseases, including Kampo medicine and the pharmacological effects of numerous crude drugs. When tracing the pharmacognostical changes of dentifrice in ancient China, we felt wonder at and admiration for the abundance of clinical experiences described in the old herbal and medical literature we researched.

Effect of a baking soda-peroxide dentifrice on post-surgical wound healing.

Science.gov (United States)

Dentino, A R; Ciancio, S G; Bessinger, M; Mather, M A; Cancro, L; Fischman, S

1995-06-01

To investigate the effect of a baking soda-hydrogen peroxide (0.75%) dentifrice on wound healing, plaque formation, gingival inflammation, patient comfort, probing depth, and clinical attachment level following gingival flap surgery. A randomized, double-blind crossover study involving 25 patients requiring bilateral maxillary gingival flap surgery was completed. The effects of twice daily brushing with a baking soda-hydrogen peroxide dentifrice (Mentadent) or a placebo dentifrice (Crest) were observed over a 28-day post-surgical period. Gingival Index (GI), plaque index (PI), probing depth (PD), clinical attachment level (CAL) and gingival bleeding index (BI) were recorded pre-surgically and at day 28 for each surgical sextant. At days 7 and 14, soft tissue appearance/wound healing (STA) was assessed based on color and edema, PIs were determined and patient comfort was ascertained by report. Post-surgical wound healing was statistically significantly improved at day 7 with the trend continuing to day 14 when Mentadent dentifrice was used as compared to Crest dentifrice. However, there was no statistical difference in the PI values between the test and control dentifrice throughout the study. Use of Mentadent may be an effective aid in the early phase of healing following gingival flap surgery.

Surface Roughness of Composite Resins after Simulated Toothbrushing with Different Dentifrices.

Science.gov (United States)

Monteiro, Bruna; Spohr, Ana Maria

2015-07-01

The aim of the study was to evaluate, in vitro, the surface roughness of two composite resins submitted to simulated toothbrushing with three different dentifrices. Totally, 36 samples of Z350XT and 36 samples of Empress Direct were built and randomly divided into three groups (n = 12) according to the dentifrice used (Oral-B Pro-Health Whitening [OBW], Colgate Sensitive Pro-Relief [CS], Colgate Total Clean Mint 12 [CT12]). The samples were submitted to 5,000, 10,000 or 20,000 cycles of simulated toothbrushing. After each simulated period, the surface roughness of the samples was measured using a roughness tester. According to three-way analysis of variance, dentifrice (P = 0.044) and brushing time (P = 0.000) were significant. The composite resin was not significant (P = 0.381) and the interaction among the factors was not significant (P > 0.05). The mean values of the surface roughness (µm) followed by the same letter represent no statistical difference by Tukey's post-hoc test (P composite resins. The dentifrice OBW caused a higher surface roughness in both composite resins.

The effect of a dentifrice containing Magnolia extract on established plaque and gingivitis in man: a six-month clinical study.

Science.gov (United States)

Hellström, M-K; Ramberg, P

2014-05-01

The aim was to evaluate the clinical effect of a dentifrice containing 0.3% Magnolia extract on dental plaque and gingivitis. The trial was a 6-month double-blind, stratified, randomized and 2-armed parallel group study. Forty-six subjects in the test group brushed their teeth with a dentifrice containing 0.3% Magnolia extract and 48 subjects in the control group brushed with a placebo dentifrice. Plaque and gingivitis were assessed at baseline, 3 and 6 months. There was a significantly larger gingivitis reduction in the Magnolia group than in the control group (0.26 ± 0.11 versus 0.11 ± 0.12) (P gingival units Gingival Index (GI score 0) in the Magnolia group than in the control group (149% versus 31%) and a larger reduction in inflamed gingival units (GI score 2/3) (60% versus 30%). Furthermore, at sites with similar amounts of plaque, less clinical signs of gingival inflammation were observed in the Magnolia group than in the control group. Six months' unsupervised use of a dentifrice containing 0.3% Magnolia extract resulted in significantly greater gingivitis reduction than a corresponding control dentifrice. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Whole mouth antimicrobial effects after oral hygiene: comparison of three dentifrice formulations.

Science.gov (United States)

Fine, Daniel H; Sreenivasan, Prem K; McKiernan, Marie; Tischio-Bereski, Debra; Furgang, David

2012-11-01

This study compared the antimicrobial effects of three commercial dentifrice formulations: sodium fluoride/triclosan/copolymer (TCN/C), stannous fluoride/sodium hexametaphosphate/zinc lactate (SnF(2)/SHMP) and sodium fluoride (NaF). Thirty-five adults (15 men and 20 women; average age 33 years and pockets oral sites and six organisms evaluated in each site, the TCN/C demonstrated significant reductions (49-83%) as compared with the other treatments (p oral sites in comparison with the NaF, or the SnF(2)/SHMP dentifrice formulations as seen 12 h after brushing. © 2012 John Wiley & Sons A/S.

Evaluating the anti-plaque efficacy of meswak (Salvadora persica containing dentifrice: A triple blind controlled trial

Directory of Open Access Journals (Sweden)

Puneet Gupta

2012-01-01

Full Text Available Introduction: The growing field of alternative medicine has shown that dentifrices based on plant extracts are available in the market but there is little or no research to prove or refute the efficacy of dentifrices containing combination of herbal components. Aim: The study was conducted to evaluate the anti-plaque efficacy of a commercially available Meswak containing dentifrice compared to the conventional dentifrice using a randomized, triple blind, parallel design method. Materials and Methods: A total of 350 subjects were selected. All the subjects (aged 13-54 years were given the test dentifrices, packed in plain white color-coded tubes. The subjects were instructed to brush their teeth twice daily for 2 min with the allocated dentifrice. The total study duration was 4 weeks. Plaque scores were recorded at the baseline, 2 weeks and 4 weeks respectively, using the Turesky modification of the Quigley Hein Plaque Index. Results: The results showed that there were significant differences in the reduction of plaque by the herbal dentifrice, Meswak (Salvadora persica on intra-group and inter-group comparison. Conclusion: It was concluded that further research is required to know the dental benefits of herbal products being incorporated into the commercially available dentifrices.

New laboratory methods to study tooth surface coverage and interproximal plaque control by dentifrice products.

Science.gov (United States)

Xu, Tao; Herles, Susan M; Barnes, Virginia M

2004-01-01

To develop and test an in vitro tooth model for use in conjunction with laboratory methods to study interproximal effects and efficacy of dentifrices. The application of the model should offer visual evaluation of dentifrice coverage of the tooth surface, and measure dental plaque control at posterior interdental spaces with a dentifrice. The dentifrice products tested with the model were: Colgate Total 2 in 1 Toothpaste and Mouthwash (CTTM), Colgate Total dentifrice (CTD), and Colgate Regular dentifrice (CRD). Extracted human posterior teeth were disinfected, cleaned, aligned, and mounted in denture acrylic. In the area coverage method, tooth surface coverage and penetration of two different forms of dentifrice products (CTTM and CRD) were compared using digital photography. In the interproximal plaque control method, the teeth were coated with human saliva and incubated anaerobically with a mixture of representative oral bacteria for six hours at 37 degrees C. In vitro dental plaque was assessed after brushing the facial surface with one of the three dentifrice products using a clinical plaque scoring index. The area coverage method demonstrated that both dentifrice products tested covered approximately 70% of the facial tooth surface; the CTTM dentifrice coverage on the lingual tooth surface was significantly higher than the coverage for the CRD dentifrice. With the interproximal plaque control method, in the presence of an active ingredient, the CTTM dentifrice had equivalent efficacy to the CTD dentifrice. Both CTTM and CTD were significantly superior to the CRD for interproximal dental plaque control. Using the developed tooth model, two assessment methods have been shown to have the potential to demonstrate tooth surface coverage, and to assess the potential efficacy of a dentifrice for the control of interproximal dental plaque. This process can indicate potential clinical evaluation of an oral care product, and support clinical findings with controlled

Microstructural analysis of demineralized primary enamel after in vitro toothbrushing

Directory of Open Access Journals (Sweden)

Neves Aline de Almeida

2002-01-01

Full Text Available The aim of this study was to investigate, in vitro, the morphological characteristics of demineralized primary enamel subjected to brushing with a dentifrice with or without fluoride. In order to do so, 32 enamel blocks were divided in 4 different groups containing 8 blocks each. They were separately immersed in artificial saliva for 15 days. The experimental groups were: C - control; E - submitted to etching with 37% phosphoric acid gel (30 s; EB - submitted to etching and brushing 3 times a day with a non-fluoridated dentifrice; EBF = submitted to etching and brushing 3 times a day with a fluoridated dentifrice. The toothbrushing force was standardized at 0.2 kgf and 15 double strokes were performed on each block. After the experimental period, the samples were prepared and examined under SEM. The control group (C showed a smooth surface, presenting scratches caused by habitual toothbrushing. The etched samples (E exhibited different degrees of surface disintegration, but the pattern of acid etching was predominantly the type II dissolution. The brushed surfaces were smooth, with elevations which corresponded to the exposure of Tomes? process pits and depressions which corresponded to interrod enamel. Particles resembling calcium carbonate were found in the most protected parts of the grooves. No morphological differences were observed between brushing with fluoridated (EBF and non-fluoridated (EB dentifrice. The results suggest that the mechanical abrasion caused by brushing demineralized enamel with dentifrice smoothes the rough etched surface, and the presence of fluoride does not cause morphological modifications in this pattern.

Three-dimensional in vitro measurements of tooth wear using fluoridated dentifrices.

Science.gov (United States)

Al-Mashhadani, A; Plygkos, I; Bozec, L; Rodriguez, J M

2016-09-01

The aim of this study was to compare differences in wear of human enamel and dentine in vitro using a 3D measurement method comparing silica versus non-silica containing fluoridated dentifrices (Colgate Total(™) [CT] or Fluor Protector Gel(™) [FPG]). Mounted native enamel (n = 36) and polished dentine (n = 36) samples were subjected to 10 wear cycles. Each cycle consisted of: (1) 1 hour remineralization in artificial saliva (AS); (2) 10 minute erosion (0.3% citric acid; pH = 2.8); (3) 2 minute toothbrush abrasion in AS (G1, control) or a slurry of 3:1 by weight of AS:dentifrice (G2 = CT; G3 = FPG) under a load of 2 N. Each group contained 12 enamel and 12 dentine samples. Paired pre- and post-wear scans made with a contacting scanner were digitally superimposed using ball bearings as datum. Mean and (SD) enamel wear was G1 = 21.9 μm (6.4); G2 = 15.2 μm (2.8); G3 = 16.9 μm (3.2). Enamel wear was not different between dentifrices (p = 0.99). Both dentifrices resulted in less enamel wear compared to the control (p Dental Association.

Wear of dentine in vitro by toothpaste abrasives and detergents alone and combined.

Science.gov (United States)

Moore, C; Addy, M

2005-12-01

To measure in vitro the abrasion of dentine by toothpaste detergents and abrasives alone and combined. Detergents used were tego betain, sodium lauryl sulphate (SLS), adinol and pluronic diluted to 1% w/v. Abrasives were three artificial silicas, tixosil 73 and 123 and Zeodent 113, and calcium carbonate used at 2.5% w/v. Flat human dentine specimens were brushed with aqueous detergent solutions or abrasive slurries, detergent abrasive slurries and water for 20,000 brush strokes. Dentine loss was measured by non-contacting profilometry at 10,000 and 20,000 strokes. Silica particle size distribution was measured by laser deflection. Loss of dentine occurred with all detergents, abrasives and detergent abrasion combinations, but was not linear with number of brush strokes. Water appeared to remove the smear layer only, but all detergents exceeded the predicted smear layer thickness. The silica abrasives differed in abrasion properties despite similar particle size distribution. Different detergents modulated the abrasives actions in mainly positive or mainly negative directions. Detergents appear able to attack the dentine surface to produce wear. Abrasives vary considerably in wear produced under similar conditions. Detergents modulate the effect of abrasives in a way that may reflect the rheological properties of the mixture.

Calcium release rates from tooth enamel treated with dentifrices containing whitening agents and abrasives.

Science.gov (United States)

Araujo, Danilo Barral; Silva, Luciana Rodrigues; de Araujo, Roberto Paulo Correia

2010-01-01

Tooth whitening agents containing hydrogen peroxide and carbamide peroxide are used frequently in esthetic dental procedures. However, lesions on the enamel surface have been attributed to the action of these products. Using conventional procedures for separating and isolating biological structures, powdered enamel was obtained and treated with hydrogen peroxide, carbamide peroxide, and sodium bicarbonate, ingredients typically found in dentifrices. The enamel was exposed to different pH levels, and atomic emission spectrometry was used to determine calcium release rates. As the pH level increased, the rate of calcium release from enamel treated with dentifrices containing whitening agents decreased. Carbamide peroxide produced the lowest amount of decalcification, while sodium bicarbonate produced the highest release rates at all pH levels.

In vitro assessments of experimental NaF dentifrices containing a prospective calcium phosphate technology.

Science.gov (United States)

Karlinsey, Robert L; Mackey, Allen C; Stookey, George K; Pfarrer, Aaron M

2009-06-01

To determine the fluoride dose response of experimental NaF dentifrices containing a prospective calcium phosphate technology, along with the corresponding relative enamel and dentin abrasion values. 3 mm diameter bovine enamel specimens were mounted, ground and polished, and softened in a carbopol-lactic acid solution (pH = 5.0) for 36 hours at 37 degrees C. Specimens were then measured for baseline Vickers microhardness and stratified (N = 18, mean VHN = 33) into eight groups. These groups consisted of a placebo paste, four test dentifrices (A, B, C, D) with three of the four (A, B, C) containing a promising calcium phosphate ingredient, Crest Cavity Protection, MI Paste Plus, and PreviDent Booster 5000. The groups were cycled in a lesion reversal pH cycling model consisting of four 2-minute treatment periods (diluted 1:3 with DI water) and one 4-hour acid challenge (carbopol-lactic acid, pH = 5.0) per day. Between these events, specimens were immersed in artificial saliva (pH = 7.0). After 20 days of cycling, the specimens were microdrilled and analyzed for fluoride content, and also measured for Vickers surface microhardness after 10 and 20 days of cycling and after a 2-hour and 16-hour post-cycle acid challenge (carbopol-lactic acid, pH = 5.0). Separately, relative dentin and enamel abrasion (RDA and REA) were performed using the ADA recommended radiotracer method. A fluoride dose response was observed for the test dentifrices after 10 and 20 days of pH cycling, with test dentifrice C promoting the highest remineralization among the groups while both the MI Paste Plus and PreviDent systems provide the least remineralization (one-way ANOVA, SNK, P dentin (one-way ANOVA, SNK, P < 0.05). Altogether, these data show the developmental test dentifrices demonstrate a fluoride dose response and show great promise in remineralizing white-spot enamel lesions relative to MI Paste Plus and PreviDent.

In vitro assessment of the effectiveness of whitening dentifrices for the removal of extrinsic tooth stains

Directory of Open Access Journals (Sweden)

Débora Alves Nunes Leite Lima

2008-06-01

Full Text Available This in vitro study evaluated the effectiveness of whitening dentifrices for the removal of extrinsic tooth stains. Twenty dental blocks (4 x 4 mm, including enamel and dentine, removed from freshly extracted bovine incisors, were randomly divided into 4 groups: G1 - distilled water, G2 - Colgate, G3 - Crest Extra Whitening and G4 - Rapid White. In all specimens, the dentin was covered with colorless nail polish, and the enamel was left exposed. Next, the specimens were immersed in a solution of black tea, which was changed every 24 h, for a period of 6 days. After this period, a photo-reflectance reading was taken (Time 1 with a spectrometer. The stained specimens were then submitted to linear brushing movements (5,000 cycles using brushes (Oral B-Soft coupled to an automatic toothbrushing machine, under a static axial load of 200 g and with a speed of 4 movements/second, at 37°C, with the dentifrice or water being injected every 60 s. When toothbrushing ended, a second photo-reflectance reading was taken (Time 2. The results were submitted to two-criteria analysis of variance (ANOVA and to the Tukey test ( = 0.05. When the two times for a same group were compared, Time 2 presented the highest reflectance values with statistical difference only for G3 and G4. Among the dentifrices tested, only the Rapid White group differed from the control group, presenting the highest reflectance values. Only the whitening dentifrice Rapid White was effective for the removal of extrinsic stains.

Enhanced anticaries efficacy of a 0.243% sodium fluoride/10% xylitol/silica dentifrice: 3-year clinical results.

Science.gov (United States)

Sintes, J L; Escalante, C; Stewart, B; McCool, J J; Garcia, L; Volpe, A R; Triol, C

1995-10-01

To evaluate the efficacy of a sodium fluoride (NaF)/silica/xylitol dentifrice compared with that of a positive control NaF/silica dentifrice on caries increments in school children over a 3-year period in an area without an optimal level of fluoride in the drinking water (mean level schools in the San Jose, Costa Rica metropolitan area. Clinical dental examinations were performed at participating schools utilizing portable dental equipment. Caries evaluations employed conventional tactile/visual methodology consisting of artificial light, dental mirrors and single-edge #23 explorers. Children accepted into the study were stratified by age and sex into two balanced groups within each school, and randomly assigned to use either a positive control dentifrice containing 0.243% NaF/silica or a test dentifrice containing 0.234% NaF/silica/10% xylitol. Children were instructed to brush with the assigned dentifrice twice daily. Caries evaluations were conducted at baseline, 2 years, and 3 years. After 3 years, subjects using the 0.234% NaF/silica/10% xylitol dentifrice had statistically significantly reduced decayed/filled surfaces (DFS; -12.3% reduction; P < or = 0.001) and decayed/filled buccal and lingual surfaces (DFS-BL; -10.5% reduction; P < or = 0/01).

Abrasive Wear of Four Direct Restorative Materials by Standard and Whitening Dentifrices

Science.gov (United States)

2013-06-01

Weader, E., Liscombe, C., & Holt, J.S. (2005). The measurement of enamel and dentine abrasion by tooth - whitening products using an in situ model...ABRASION OF TOOTH STRUCTURE Hard tissue abrasion is a familiar consequence of toothbrushing. Enamel , dentin, and cementum differ in their...LESIONS Cervical enamel wear is common; however, relatively few epidemiologic studies have distinguished between cervical enamel wear and tooth wear in

Evaluation of a dentifrice containing 8% arginine, calcium carbonate, and sodium monofluorophosphate to prevent enamel loss after erosive challenges using an intra-oral erosion model.

Science.gov (United States)

Sullivan, R; Rege, A; Corby, P; Klaczany, G; Allen, K; Hershkowitz, D; Godder, B; Wolff, M

2014-01-01

The objective of this study was to assess the ability of a dentifrice containing 8% arginine and calcium carbonate (Pro-Argin' Technology), and 1450 ppm fluoride as sodium monofluorophosphate (MFP) to prevent enamel loss from an erosive acid challenge in comparison to a silica-based dentifrice with 1450 ppm fluoride as MFP using an intra-oral erosion model. The intra-oral clinical study used a double blind, two-treatment, crossover design. A palatal retainer was used to expose the enamel specimens to the oral environment during the five-day treatment period. The retainer was designed to house three partially demineralized bovine enamel samples. The study population was composed of 24 adults, ages 18 to 70 years. The study consisted of two treatment periods, with a washout period lasting seven (+/- three) days preceding each treatment phase. A silica-based dentifrice without fluoride was used during the washout period. The Test Dentifrice used in this study contained 8% arginine and calcium carbonate (Pro-Argin Technology), and 1450 ppm fluoride as sodium monofluorophosphate (MFP). The Control Dentifrice was silica-based and contained 1450 ppm fluoride as MFP. The treatment period lasted five days, during which the panelists wore the retainer 24 hours a day (except during meals and the ex vivo acid challenges) and brushed with their assigned product while wearing the retainer. The panelists brushed once in the morning and once in the evening each day for one minute, followed by a one-minute swish with the slurry and a rinse with 15 ml of water. The panelists brushed only their teeth and not the specimens directly. There were four ex vivo challenges with 1% citric acid dispersed throughout the day: two in the morning, one in the afternoon, and one in the evening. Mineral loss was monitored by a quantitative light fluorescence (QLF) technique. Twenty-three of 24 subjects successfully completed the study. The one subject who did not complete the study did so for

Eugenia uniflora Dentifrice for Treating Gingivitis in Children: Antibacterial Assay and Randomized Clinical Trial.

Science.gov (United States)

Jovito, Vanessa de Carvalho; Freires, Irlan Almeida; Ferreira, Danilo Augusto de Holanda; Paulo, Marçal de Queiroz; Castro, Ricardo Dias de

2016-01-01

School-age children are frequently at high risk for the onset of biofilm-dependent conditions, including dental caries and periodontal diseases. The objective of this study was to evaluate the clinical efficacy of a dentifrice containing Eugenia uniflora Linn. (Surinam cherry) extract versus a triclosan-based comparator in treating gingivitis in children aged 10-12 years. The in vitro antibacterial potential of the dentifrice was tested against oral pathogens (Streptococcus mutans, Streptococcus oralis and Lactobacillus casei). Then a phase-II clinical trial was conducted with 50 subjects aged 10-12 years, with clinical signs of gingivitis. The subjects were randomly assigned to the experimental group (n=25) and control group (n=25), in which participants used the experimental dentifrice and a triclosan-based fluoridated dentifrice (Colgate Total 12(r)), respectively. Clinical examinations assessed the presence of gingivitis (primary outcome) and biofilm accumulation (secondary outcome) using the Gingival-Bleeding Index (GBI) and Simplified Oral Hygiene Index (OHI-S), respectively, at baseline and after seven days of tooth brushing 3x/day. The data were analyzed using paired and unpaired t-test (GBI) and Wilcoxon and Mann-Whitney (OHI-S), with p≤0.05. The experimental dentifrice showed efficient antibacterial activity in vitro. In the clinical trial, a significant reduction in gingival bleeding was observed in both experimental and control groups (puniflora dentifrice showed anti-gingivitis properties in children aged 10-12 years. Thus, it may be a potentially efficient and safe product to be used alternatively in preventive dental practice.

The effectiveness of dentifrices without and with sodium lauryl sulfate on plaque, gingivitis and gingival abrasion : a randomized clinical trial

NARCIS (Netherlands)

Sälzer, S.; Rosema, N.A.M.; Martin, E.C.J.; Slot, D.E.; Timmer, C.J.; Dörfer, C.E.; van der Weijden, G.A.

2016-01-01

Objectives The aim of this study was to compare the efficacy of a dentifrice without sodium lauryl sulfate (SLS) to a dentifrice with SLS in young adults aged 18–34 years on gingivitis. Material and methods One hundred twenty participants (non-dental students) with a moderate gingival inflammation

Surface characterization of current composites after toothbrush abrasion.

Science.gov (United States)

Takahashi, Rena; Jin, Jian; Nikaido, Toru; Tagami, Junji; Hickel, Reinhard; Kunzelmann, Karl-Heinz

2013-01-01

The present study was designed to evaluate the surface roughness and the gloss of current composites before and after toothbrush abrasion. We assessed forty dimensionally standardized composite specimens (n=8/group) from five composites: two nanohybrids (i. e., IPS Empress Direct Enamel and IPS Empress Direct Dentin), two microhybrids (i. e., Clearfil AP-X and Filtek Z250) and one organically modified ceramics (Admira). All of the specimens were polished with 4000-grid silicon carbide papers. Surface roughness was measured with a profilometer and gloss was measured with a glossmeter before and after powered toothbrush abrasion with a 1:1 slurry (dentifrice/tap water) at 12,000 strokes in a toothbrush simulator. There was a significant increase in the surface roughness and a reduction in gloss after toothbrush abrasion in all of the composites except Clearfil AP-X (pgloss (R(2)=0.191, p<0.001).

The effect of baking soda/hydrogen peroxide dentifrice (Mentadent) and a 0.12 percent chlorhexidine gluconate mouthrinse (Peridex) in reducing gingival bleeding.

Science.gov (United States)

Taller, S H

1993-01-01

The purpose of this study was to determine the effectiveness of a baking soda/hydrogen peroxide dentifrice, Mentadent, and a 0.12 percent chlorhexidine gluconate mouthrinse, Peridex, in reducing gingival bleeding. Forty subjects were divided into three groups; the baking soda group, the chlorhexidine group and the control group. All groups received oral hygiene instruction and brushed and flossed three times per day. Bleeding point scores were evaluated at baseline and at five weeks. The baking soda/hydrogen peroxide group used the supplied dentifrice as their sole toothpaste. The 0.12 percent chlorhexidine group used the mouthrinse twice per day. The control group performed oral hygiene as instructed. At five weeks, the 0.12 percent chlorhexidine mouthrinse significantly reduced gingival bleeding. The dentifrice and control groups revealed no statistically significant reductions. The results indicate that the 0.12 percent chlorhexidine mouthrinse is useful in improving oral health, whereas the baking soda/hydrogen peroxide dentifrice offered no advantages to conventional oral hygiene.

Effectiveness of a new dentifrice with baking soda and peroxide in removing extrinsic stain and whitening teeth.

Science.gov (United States)

Ghassemi, A; Hooper, W; Vorwerk, L; Domke, T; DeSciscio, P; Nathoo, S

2012-01-01

The primary purpose of this randomized, controlled, six-week clinical trial was to determine the effectiveness and safety of a new whitening dentifrice in removing extrinsic tooth stain and whitening teeth. An additional two-week exploratory study was conducted to determine whether the whitening or stain-prevention activity of the dentifrice would persist following cessation of use. In the first study (Phase I), one-hundred and forty-six qualifying subjects were randomly assigned to either a sodium bicarbonate whitening dentifrice group (Arm & Hammer Advance White Extreme Whitening Baking Soda and Peroxide Toothpaste) or a silica-based negative control dentifrice group, and brushed twice daily with their assigned dentifrice for six weeks. Tooth shade on the labial surfaces of the eight incisors was assessed using a Vita Classic shade guide, and extrinsic tooth stain was scored using a Modified Lobene Stain Index (MLSI) at baseline, week 4, and week 6. In Phase II (after the week 6 examination), volunteers from the Arm & Hammer whitening dentifrice group were randomly assigned to continue using the whitening dentifrice or to use the negative control dentifrice twice daily for two weeks. The six-week shade and stain index scores served as the baseline for this exploratory phase and were rescored after two weeks. The whitening dentifrice group had statistically significant (p < 0.0001) mean shade score reductions of 1.82 and 2.57 from baseline to weeks 4 and 6, respectively. For the same periods, the negative control dentifrice group was virtually unchanged from baseline. For tooth stain, the MLSI total mean scores for the whitening dentifrice group showed statistically significant (p < 0.0001) decreases from baseline of 1.42 (41.6%) and 2.11 (61.6%) at weeks 4 and 6, respectively. In contrast, the negative control dentifrice group had a MLSI reduction of 0.07 at week 4 and a 0.06 increase at week 6. Between-group analyses using baseline-adjusted ANCOVA showed the

Cleaning power and abrasivity of European toothpastes.

Science.gov (United States)

Wülknitz, P

1997-11-01

For 41 toothpastes available to European consumers in 1995, the cleaning efficacy was evaluated in comparison with abrasivity on dentin (RDA value). For cleaning power assessment, a modified pellicle cleaning ratio (PCR) measurement method was developed. The method is characterized by a five-day tea-staining procedure on bovine front teeth slabs on a rotating wheel, standardized brushing of the slabs in a V8 cross-brushing machine, and brightness measurement by a chromametric technique. All tested products were in accordance with the new DIN/ISO standard 11,609 for toothpastes in terms of dentin abrasivity. Not a single product exceeded an RDA value of 200. The majority of toothpastes (80%) had an RDA value below 100. Only three products surpassed the reference in cleaning power. Most products (73%) had a cleaning power (PCR value) between 20 and 80. The correlation between cleaning power and dentin abrasion was low (r = 0.66), which can be explained with the different influence on dentin and stains by factors like abrasive type, particle surface and size, as well as the chemical influence of other toothpaste ingredients. Some major trends could be shown on the basis of abrasive types. The ratio PCR to RDA was rather good in most silica-based toothpastes. A lower ratio was found in some products containing calcium carbonate or aluminum trihydrate as the only abrasive. The addition of other abrasives, such as polishing alumina, showed improved cleaning power. Some active ingredients, especially sequenstrants such as sodium tripolyphosphate or AHBP, also improve the PCR/RDA ratio by stain-dissolving action without being abrasive. The data for some special anti-stain products did not differ significantly from standard products. Compared with data measured in 1988, a general trend toward reduced abrasivity without loss of cleaning efficacy could be noticed on the European toothpaste market. This may be mostly due to the increased use of high-performance abrasives such

Control of oral malodour by dentifrices measured by gas chromatography.

Science.gov (United States)

Newby, Evelyn E; Hickling, Jenneth M; Hughes, Francis J; Proskin, Howard M; Bosma, Marylynn P

2008-04-01

To evaluate the effect of toothpaste treatments on levels of oral volatile sulphur compounds (VSCs) measured by gas chromatography in two clinical studies. These were blinded, randomised, controlled, crossover studies with 16 (study A) or 20 (study B) healthy volunteers between the ages of 19-54. Study A: breath samples were collected at baseline, immediately and lhr after brushing. Four dentifrices (Zinc A, Zinc B, commercially available triclosan dentifrice and zinc free control) were evaluated. Study B: breath samples were collected at baseline, immediately, 1, 2, 3 and 7 hours after treatment. Subjects consumed a light breakfast then provided an additional breath sample between baseline assessment and treatment. Two dentifrices (gel-to-foam and a commercially available triclosan dentrifrice) were evaluated. Breath samples were collected in syringes and analysed for VSCs (hydrogen sulphide, methyl mercaptan and Total VSCs) utilising gas chromatography (GC) with flame photometric detection. Study A: immediately after treatment, a statistically significant reduction in VSCs from baseline was observed for Zinc A product only. A statistically significant reduction in VSCs from baseline was observed after 1 hour for all products. Both zinc products exhibited a significantly greater reduction from baseline VSCs than Colgate Total and Control at all time points. Study B: a statistically significant reduction in VSCs from baseline was observed at all time points for both products. The gel-to-foam product exhibited significantly greater reduction from baseline Total VSC concentration than Colgate Total at all time points from 1 hour post-treatment. Control of oral malodour by toothpaste treatment, evaluated as VSC levels using GC, has been demonstrated. Zinc is effective at reducing VSCs and the efficacy of zinc is formulation dependent. A gel-to-foam dentifrice was more effective at reducing VSCs than Colgate Total up to 7 hours.

Salivary Fluoride level in preschool children after toothbrushing with standard and low fluoride content dentifrice, using the transversal dentifrice application technique: pilot study

Directory of Open Access Journals (Sweden)

Fabiana Jandre Melo

2008-01-01

Full Text Available Objective: To investigate the salivary fluoride concentration in pre-school children after toothbrushing with dentifrice containing standard (1100ppmF/NaF and low (500ppmF/NaF fluoride concentration, using the transversal technique of placing the product on the toothbrush. Methods: Eight children of both sexes, ranging from 4 to 9 years, and 5 years and 6 months of age, participated in the study. The experiment was divided into two phases with a weekly interval. In the first stage, the children used the standard concentration dentifrice for one week, and in the second, the low concentration product. Samples were collected at the end of each experimental stage, at the following times: Before brushing, immediately afterwards, and after 15, 30 and 45 minutes. The fluoride contents were analyzed by the microdiffusion technique. Statistical analysis was done by the analysis of variance ANOVA and Student’s-t test (p<0.05. Results: The salivary fluoride concentration was significantly higher at all times, when the standard concentration product was used. The comparison between the Halogen concentration found before bushing and immediately afterwards, showed that there was a 6.8 times increase in the standard dentifrice (0.19 x 1.29μgF/ml and in the low concentration product, an increase of 20.5 times (0.02 x 0.41μgF/ml. Conclusion: Toothbrushing with both products promoted relevant increases in the salivary fluoride concentration; however, longitudinal studies are necessary to verify the clinical result of this measurement.

A randomized clinical trial evaluating gingivitis and plaque reduction of an oscillating-rotating power brush with a new brush head with angled bristles versus a marketed sonic brush with self-adjusting technology.

Science.gov (United States)

Klukowska, Malgorzata; Grender, Julie M; Conde, Erinn; Ccahuana-Vasquez, Renzo Alberto; Ram Goyal, C

2014-08-01

To compare the efficacy of an oscillating-rotating power toothbrush with a novel brush head incorporating angled CrissCross bristles (Oral-B Pro 7000 SmartSeries and Oral-B CrossAction brush head) versus a marketed sonic toothbrush (Colgate ProClinical A1500 with the Triple Clean brush head) in the reduction of gingivitis and plaque over a 6-week period. This was a single center, randomized, open label, examiner-blind, 2-treatment, parallel group study. Study participants who met the entrance criteria were enrolled in the study and randomly assigned to one of the two toothbrush groups. Study participants brushed with their assigned toothbrush and a marketed fluoride dentifrice for 2 minutes twice daily at home for 6 weeks. Gingivitis and plaque were evaluated at baseline and Week 6. Gingivitis was assessed using the Modified Gingival Index (MGI) and Gingival Bleeding Index (GBI) and plaque was assessed using the Rustogi Modified Navy Plaque Index (RMNPI). Data was analyzed using the ANCOVA with baseline as the covariate. In total, 130 study participants were randomized to treatment resulting in 64 study participants per group completing the study. Both brushes produced statistically significant (P gingivitis and plaque measures relative to baseline. The oscillating-rotating,brush with the novel brush head demonstrated statistically significantly (P gingivitis measures, as well as whole mouth and interproximal plaque measures, compared to the sonic toothbrush. The benefit for the oscillating- rotating brush over the sonic brush was 21.3% for gingivitis, 35.7% for gingival bleeding, 34.7% for number of bleeding sites, 17.4% for whole mouth plaque, and 21.2% for interproximal plaque. There were no adverse events reported or observed for either brush.

In Vitro and In Vivo Evaluations of the Anticalculus Effect of a Novel Stabilized Stannous Fluoride Dentifrice.

Science.gov (United States)

He, Tao; Anastasia, Mary Kay; Zsiska, Marianne; Farmer, Teresa; Schneiderman, Eva; Milleman, Jeffery L

2017-12-01

To evaluate the effect of a novel stannous fluoride dentifrice with zinc citrate on calculus inhibition using both in vitro and clinical models. Each investigation tested a novel stabilized 0.454% stannous fluoride dentifrice with zinc citrate as an anticalculus agent (Crest® Pro-Health™ smooth formula) compared to a negative control fluoride dentifrice. The in vitro study used the modified Plaque Growth and Mineralization Model (mPGM). Plaque biofilms were prepared and mineralized by alternate immersion of glass rods in human saliva and artificial mineralization solution. Treatments of 25% w/w dentifrice/water slurries were carried out for 60 seconds daily for 6 days, between saliva and mineralization solution immersions. Plaque calcium levels were determined by digestion and inductively coupled plasma optical emission spectroscopy. Student's t-test (p < 0.05) was used for statistical analysis. The clinical study was a parallel group, double-blind, randomized, and controlled trial. Following a dental prophylaxis, subjects entered a two-month run-in phase. At the end, they received a Volpe-Manhold Index (V-MI) calculus examination. Eighty (80) qualified subjects who had formed at least 9 mm of calculus on the linguals of the mandibular anterior teeth were re-prophied and randomly assigned to either the stannous fluoride dentifrice or the negative control. Subjects brushed twice daily, unsupervised, during the three-month test period, returning at Weeks 6 and 12 for safety and V-MI examinations. Statistical analyses were via ANCOVA. In vitro mPGM: The stabilized stannous fluoride dentifrice showed 20% less in vitro tartar formation, measured as calcium accumulation normalized by biofilm mass, versus the negative control (106.95 versus 133.04 µg Ca/mg biofilm, respectively, p < 0.05). Clinical Trial: Seventy-eight (78) subjects completed with fully evaluable data. The stannous fluoride dentifrice group had 15.1% less adjusted mean calculus at Week 6 compared to

Control of Established Gingivitis and Dental Plaque Using a 1450 ppm Fluoride/Zinc-based Dentifrice: A Randomized Clinical Study.

Science.gov (United States)

Zhong, Y; Li, X; Hu, D Y; Mateo, L R; Morrison, B M; Delgado, E; Zhang, Y P

2015-01-01

To investigate the clinical efficacy in controlling established gingivitis and dental plaque of a 1450 ppm fluoride as sodium monofluorophosphate (SMFP)/zinc-based dentifrice, as compared to a zinc-free dentifrice with 1450 ppm fluoride as SMFP after six months product use. A six-month clinical study, with eighty-six (86) subjects, was conducted in Chengdu, China, using a double-blind, randomized, parallel-group treatment design. After a baseline evaluation, study subjects were randomly assigned to one of the two study treatments: 1) 1450 ppm fluoride as SMFP/zinc-based dentifrice (Test) or 2) 1450 ppm fluoride as SMFP/zinc-free dentifrice (Negative Control). Subjects were provided with a soft bristle toothbrush and brushed their teeth twice daily (morning and evening) for one minute with their assigned dentifrice. After three months, and again after six months of product use, subjects returned to the testing facility for their followup gingivitis and plaque examinations. Statistical analyses were performed separately for the gingivitis assessments and dental plaque assessments using the appropriate statistical methods. All statistical tests of hypotheses were two-sided, and employed a level of significance of α = 0.05. After three and six months of product use, subjects assigned to the Test treatment exhibited statistically significant (p gingival index and plaque index scores as compared to subjects assigned to the Negative Control treatment. The results of this single-center, double-blind, parallel-group and randomized clinical study support the conclusion that a 1450 ppm fluoride as SMFP/zinc-based dentifrice provides clinically meaningful and statistically significant reductions in gingivitis (23.8%) and dental plaque (22.5%) as compared to a 1450 ppm fluoride as SMFP/zinc-free dentifrice over a six-month period of twice-daily product use.

The scientific rationale and development of an optimized dentifrice for the treatment of dentin hypersensitivity.

Science.gov (United States)

Tavss, Edward A; Fisher, Steven W; Campbell, Shannon; Bonta, Yolanda; Darcy-Siegel, Joann; Blackwell, Bernie L; Volpe, Anthony R; Miller, Steven E

2004-02-01

To describe the development of a new dentin hypersensitivity treatment, Colgate Sensitive Maximum Strength dentifrice, containing 5% potassium nitrate as the anti-hypersensitivity active agent. The objective was to develop a home-use hypersensitivity dentifrice that would be superior to the market leader, improving on what is available, which also contains 5% potassium nitrate as the anti-hypersensitivity active agent. In vivo (clinicals, taste evaluation and rat caries), in vitro (potassium flux) and analytical (rheology, dispensed volume, scanning electron microscopy, electron scanning chemical analysis and radioactive dentin abrasion) methods were performed. The objective was accomplished with the development of a new activated silica technology that resulted in enhanced potassium ion activity. In vitro documentation, supported by clinical studies, demonstrated that the resulting formula is more effective than the market leader for relief of hypersensitivity pain. Fast pain relief in less than 2 weeks and long-lasting protection against pain with regular use have also been clinically documented. Furthermore, FDA-required in vivo and in vitro studies indicate that this formula, which contains 0.45% stannous fluoride (1100 ppm fluoride) as the anti-caries active agent, is effective against caries. Good taste, acceptable rheology, acceptable abrasivity, and cosmetic and chemical stability have all been engineered into this unique dentin hypersensitivity treatment. In summary, a highly efficacious consumer friendly treatment for dentin hypersensitivity has been developed.

The comparative efficacy of stabilized stannous fluoride dentifrice, peroxide/baking soda dentifrice and essential oil mouthrinse for the prevention of gingivitis.

Science.gov (United States)

Beiswanger, B B; McClanahan, S F; Bartizek, R D; Lanzalaco, A C; Bacca, L A; White, D J

1997-01-01

This double-blind parallel-design clinical study compared the efficacy of a stabilized stannous fluoride dentifrice (Crest Plus Gum Care), baking soda and peroxide (NaF) dentifrice (Mentadent), and essential oil mouthrinse (Listerine) to a conventional NaF dentifrice (Crest) for the control of plaque, gingivitis and gingival bleeding over six months. Following an initial baseline examination and stratification, subjects received a complete oral prophylaxis and were distributed assigned test products. Following three and six months, subjects re-visited the clinic for examinations. Evaluations at baseline and at 3 and 6 months included soft tissue status. Löe-Silness gingivitis/gingival bleeding, Silness-Löe plaque and dental stain. Results subsequent to six months of product use were as follows: At six months, the stabilized stannous fluoride dentifrice was observed to produce statistically significant 17.5% reductions in gingivitis and 27.5% reductions in gingival bleeding relative to the NaF dentifrice. The combination of sodium fluoride dentifrice and essential oil mouthrinse produced statistically significant reductions of 7.4% in gingivitis and 10.8% in plaque as compared with the NaF dentifrice. The stabilized stannous fluoride dentifrice produced statistically significant reductions in both gingivitis (10.8%) and gingival bleeding (23.0%) relative to the combination of sodium fluoride dentifrice and essential oil mouthrinse. The baking soda and peroxide (NaF) dentifrice did not provide reductions in gingivitis, plaque or gingival bleeding as compared with the conventional NaF dentifrice. The stabilized stannous fluoride dentifrice provided statistically significant reductions in gingivitis as compared with the baking soda and peroxide dentifrice following six months of use, and both the essential oil mouthrinse and stabilized stannous fluoride dentifrice provided statistically significant reductions in gingivitis as compared with the baking soda and

Comparative Efficacy of a Soft Toothbrush with Tapered-tip Bristles to an ADA Reference Toothbrush on Gingival Abrasion over a 12-Week Period.

Science.gov (United States)

Gallob, John; Petrone, Dolores M; Mateo, Luis R; Chaknis, Patricia; Morrison, Boyce M; Panagakos, Foti; Williams, Malcolm

2016-06-01

Evaluation of the impact of a soft toothbrush with tapered-tip (Test Toothbrush) bristles and an ADA reference toothbrush (ADA Toothbrush) on gingival abrasion over a 12-week period. This was a randomized, single-center, examiner-blind, two-cell, parallel clinical research study and used the Danser Gingival Abrasion Index to assess the level of gingival abrasion after a single brushing, as well as after six weeks and 12 weeks of twice-daily brushing. Adult male and female subjects from the Central New Jersey, USA area refrained from all oral hygiene procedures for 24 hours. They reported to the study site after refraining from eating, drinking, and smoking for four hours. Following a qualifying examination using plaque and gingivitis scores along with a baseline gingival abrasion examination, subjects were randomized into two balanced groups, each group using one of the two study toothbrushes. Subjects were instructed to brush their teeth for one minute, under supervision, with their assigned toothbrush and a commercially available fluoride toothpaste (Colgate© Cavity Protection Toothpaste), after which they were again evaluated for gingival abrasion. Subjects were dismissed from the study site with their assigned toothbrush and toothpaste, and instructed to brush twice daily at home for the next 12 weeks. The subjects were instructed to brush for one minute during each tooth brushing. The subjects reported to the study site after six weeks and 12 weeks of product use, at which time they were evaluated for gingival abrasion. Seventy-one (71) subjects complied with the protocol and completed the clinical study. The results of this study showed that the Test Toothbrush provided statistically significantly (p ADA Toothbrush after a single tooth brushing, after six weeks, and after 12 weeks of product use (75.0%, 85.5%, 73.9%, respectively). The soft toothbrush with tapered-tip bristles produced significantly less gingival abrasion after 12 weeks of product use as

The antimicrobial efficacy of commercial dentifrices.

Science.gov (United States)

Haraszthy, Violet I; Zambon, Joseph J; Sreenivasan, Prem K

2010-01-01

This investigation compared the effects of a fluoride dentifrice and toothpastes formulated with antimicrobial ingredients (stannous fluoride and triclosan/copolymer) on oral micro-organisms, including those found in samples taken from the human oral cavity. Microbiological techniques determined the minimum inhibitory concentrations (MICs) of each dentifrice necessary to inhibit the growth of bacterial strains from the healthy oral cavity, as well as those found in dental caries, periodontal disease, and halitosis. Ex vivo studies utilized oral rinse samples and supragingival plaque from adults to determine antimicrobial effects on the entire microbial diversity of these samples, including biofilm-derived micro-organisms. The triclosan/copolymer dentifrice demonstrated the lowest MICs and significantly inhibited Gram-positive and Gram-negative bacteria (including the periodontal pathogens Aggregatibacter actinomycetemcomitans, Eikenella corrodens, and Fusobacterium nucleatum). In the ex vivo tests, the triclosan/copolymer dentifrice demonstrated substantial inhibition in the oral rinse samples over each treatment period (p > 0.0005) as compared to either the fluoride or stannous fluoride dentifrices. Similarly, the triclosan/copolymer dentifrice demonstrated the highest inhibition of micro-organisms in the supragingival plaque biofilm (p fluoride and stannous fluoride dentifrices (p > 0.5).

Efficacy of two commercially available dentifrices in reducing dentinal hypersensitivity

Directory of Open Access Journals (Sweden)

Prasad KVV

2010-01-01

Full Text Available Objective: A parallel design clinical study evaluated reduction in hypersensitivity after brushing for 12 weeks with Anchor toothpaste (containing potassium citrate, zinc citrate, triclosan and sodium monofluorophosphate (test and Colgate Total (sodium fluoride, silica, triclosan and copolymer (control dentifrices. Materials and Methods: Sixty adults with sensitivity to hot and cold stimulus in at least two tooth surfaces were stratified at the baseline examination by tactile, hot and cold stimuli scores in two balanced groups. Subjects were randomly allocated the test and control dentifrices and evaluated after 6 and 12 weeks of dentifrice use for hypersensitivity. Results: The two teeth that were selected in each patient were designated as two different sets. The 12 th -week scores as compared to baseline scores for tactile, heat and cold tests in the test group showed a reduction in tooth hypersensitivity by 36.67% (P < 0.01, 20.35% (P < 0.01 and 53.64 % (P < 0.01, respectively, in the first set of teeth and 43.75% (P < 0.01, 24.48% (P < 0.01 and 59.78% (P < 0.01, respectively, in the second set of teeth. The 12 th -week scores as compared to baseline scores for tactile, heat and cold tests in the control group showed a reduction in tooth hypersensitivity by 42.86% (P < 0.01, 13.02% (P < 0.01 and 45.14% (P < 0.01, respectively, in the first set of teeth and 40% (P < 0.01, 16.59% (P < 0.01 and 44.16% (P < 0.01, respectively, in the second set of teeth. Conclusions: Both the products reduced dentinal hypersensitivity in the study subjects at the end of the 12-week period. However, there was no statistically significant difference in reduction in hypersensitivity between the two products.

Abrasive wear of enamel by bioactive glass-based toothpastes.

Science.gov (United States)

Mahmood, Asad; Mneimne, Mohammed; Zou, Li Fong; Hill, Robert G; Gillam, David G

2014-10-01

To determine the abrasivity of a 45S5 bioactive glass based toothpaste on enamel as a function of the particle size and shape of the glass. 45S5 glass was synthesized ground and sieved to give various particle sized fractions toothpastes and their tooth brush abrasivity measured according to BS EN ISO11609 methodology. Enamel loss increased with increasing particle size. The percussion milled powder exhibited particles that had sharp edges and the pastes were significantly more abrasive than the pastes made with round ball milled powders. One interesting observation made during the present study was that there was preferential wear of the enamel at the dentin-enamel junction (DEJ), particularly with the coarse particle sized pastes.

Anticaries Potential of a Sodium Monofluorophosphate Dentifrice Containing Calcium Sodium Phosphosilicate: Exploratory in situ Randomized Trial.

Science.gov (United States)

Parkinson, Charles R; Siddiqi, Muhammad; Mason, Stephen; Lippert, Frank; Hara, Anderson T; Zero, Domenick T

2017-01-01

Calcium sodium phosphosilicate (CSPS) is a bioactive glass material that alleviates dentin hypersensitivity and is postulated to confer remineralization of caries lesions. This single-centre, randomized, single (investigator)-blind, placebo-controlled, crossover, in situ study explored whether the addition of 5% CSPS to a nonaqueous fluoride (F) such as sodium monofluorophosphate (SMFP)-containing dentifrice affects its cariostatic ability. Seventy-seven subjects wore 4 gauze-covered enamel specimens with preformed lesions (2 surface-softened and 2 subsurface) placed buccally on their mandibular bilateral dentures for up to 4 weeks. Subjects brushed twice daily with 1 of the 5 study dentifrices: 927 ppm F/5% CSPS, 927 ppm F/0% CSPS, 250 ppm F/0% CSPS, 0 ppm F/5% CSPS, or 0 ppm F/0% CSPS. Specimens were retrieved after either 21 (surface-softened lesions; analyzed by Knoop surface microhardness [SMH]) or 28 days (subsurface lesions; analyzed by transverse microradiography). The enamel fluoride uptake was determined for all specimens using a microbiopsy technique. The concentrations of fluoride and calcium in gauze-retrieved plaque were also evaluated. Higher dentifrice fluoride concentrations led to greater remineralization and fluoridation of both lesion types and increased plaque fluoride concentrations. CSPS did not improve the cariostatic properties of SMFP; there were no statistically significant differences between 927 ppm F/5% CSPS and 927 ppm F/0% CSPS in percent SMH recovery (p = 0.6788), change in integrated mineral loss (p = 0.5908), or lesion depth (p = 0.6622). Likewise, 0 ppm F/5% CSPS did not provide any benefits in comparison to 0 ppm F/0% CSPS. In conclusion, CSPS does not negatively impact nor does it improve the ability of an SMFP dentifrice to affect remineralization of caries lesions. © 2017 S. Karger AG, Basel.

Comparative evaluation of antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate and Tween as surfactants: an in vivo study.

Science.gov (United States)

Venu, V; Prabhakar, A R; Basappa, N

2013-01-01

The aim of the study was to determine the antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate (SLS) and Tween as surfactants. It is a double-blind cross over the study, a total of 20 children within their mixed dentition period (7-13 year) having Streptococci mutans count more than 10(6) were selected for the main study. Three types of chlorhexidine containing dentifrices were used with a washout period of 1 week. Out of the three toothpastes, one was without surfactant and other two toothpastes contained SLS and Tween as surfactants respectively. 20 volunteers brushed for 1 min during the study day with their assigned toothpaste. Saliva samples were collected before brushing, immediately after brushing and 1, 3, 5, and 7 hand sent for microbial analysis. The culture carried out by inoculating saliva sample onto Mitis salivarius agar for selective isolation of S. mutans followed by counting of colony forming unit. Group I and III (Chlorhexidine and CHX + Tween) had shown statistically significant reduction in bacterial count until 7 h when compared to their baseline values ( P < 0.001). Group II toothpaste (CHX + SLS) had shown significant reduction in bacterial count until 3 h only. On inter group comparison, Group III had shown good amount of percentage reduction in bacterial count when compared to other groups. CHX + Tween toothpaste had shown statistically significant reduction in antibacterial activity and substantivity than other groups. These findings show chlorhexidine containing toothpaste with non-ionic surfactant will be able to maintain the antibacterial property and substantivity of chlorhexidine.

Effects of toothbrush hardness on in vitro wear and roughness of composite resins.

Science.gov (United States)

Kyoizumi, Hideaki; Yamada, Junji; Suzuki, Toshimitsu; Kanehira, Masafumi; Finger, Werner J; Sasaki, Keiichi

2013-11-01

To investigate and compare the effects of toothbrushes with different hardness on abrasion and surface roughness of composite resins. Toothbrushes (DENT. EX Slimhead II 33, Lion Dental Products Co. Ltd., Tokyo, Japan) marked as soft, medium and hard, were used to brush 10 beam-shaped specimens of each of three composites resins (Venus [VEN], Venus Diamond [VED] and Venus Pearl [VEP]; HeraeusKulzer) with standardized calcium carbonate slurry in a multistation testing machine (2N load, 60 Hz). After each of five cycles with 10k brushing strokes the wear depth and surface roughness of the specimens were determined. After completion of 50k strokes representative samples were inspected by SEM. Data were treated with ANOVA and regression analyses (p composite resins increased linearly with increasing number of brushing cycles (r² > 0.9). Highest wear was recorded for VEN, lowest for VED. Hard brushes produced significantly higher wear on VEN and VEP, whereas no difference in wear by toothbrush type was detected for VED. Significantly highest surface roughness was found on VED specimens (Ra > 1.5 µm), the lowest one on VEN (Ra composite resins produced by toothbrushing with dentifrice depend mainly on the type of restorative resin. Hardness grades of toothbrushes have minor effects only on abrasion and surface roughness of composite resins. No relationship was found between abrasion and surface roughness. The grade of the toothbrush used has minor effect on wear, texture and roughness of the composite resin.

A three-year clinical comparison of a sodium monofluorophosphate dentifrice with sodium fluoride dentifrices on dental caries in children.

Science.gov (United States)

Lu, K H; Ruhlman, C D; Chung, K L; Sturzenberger, O P; Lehnhoff, R W

1987-01-01

This study compared the anticaries effects of these three fluoride-containing dentifrices: 1100 ppm F as NaF (positive control); 2800 ppm F as SMFP; and 2800 ppm F as NaF. The group using the 2800 SMFP dentifrice showed no significant differences in DMFS or DMFT, compared to the positive control, at anytime during the study. This indicated that higher levels of sodium monofluorophosphate in a dentifrice offer no advantage in caries protection over the conventional level of sodium fluoride, 1100 ppm F.

Comparative evaluation of antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate and Tween as surfactants: An in vivo study

Directory of Open Access Journals (Sweden)

V Venu

2013-01-01

Full Text Available Aim: The aim of the study was to determine the antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate (SLS and Tween as surfactants. Materials and Methods: It is a double-blind cross over the study, a total of 20 children within their mixed dentition period (7-13 year having Streptococci mutans count more than 10 6 were selected for the main study. Three types of chlorhexidine containing dentifrices were used with a washout period of 1 week. Out of the three toothpastes, one was without surfactant and other two toothpastes contained SLS and Tween as surfactants respectively. 20 volunteers brushed for 1 min during the study day with their assigned toothpaste. Saliva samples were collected before brushing, immediately after brushing and 1, 3, 5, and 7 hand sent for microbial analysis. The culture carried out by inoculating saliva sample onto Mitis salivarius agar for selective isolation of S. mutans followed by counting of colony forming unit. Results: Group I and III (Chlorhexidine and CHX + Tween had shown statistically significant reduction in bacterial count until 7 h when compared to their baseline values ( P < 0.001. Group II toothpaste (CHX + SLS had shown significant reduction in bacterial count until 3 h only. On inter group comparison, Group III had shown good amount of percentage reduction in bacterial count when compared to other groups. Conclusion: CHX + Tween toothpaste had shown statistically significant reduction in antibacterial activity and substantivity than other groups. These findings show chlorhexidine containing toothpaste with non-ionic surfactant will be able to maintain the antibacterial property and substantivity of chlorhexidine.

Polyelectrolyte brushes: a novel stable lubrication system in aqueous conditions.

Science.gov (United States)

Kobayashi, Motoyasu; Terada, Masami; Takahara, Atsushi

2012-01-01

Surface-initiated controlled radical copolymerizations of 2-dimethylaminoethyl methacrylate (DMAEMA), 2-(methacryloyloxy)ethyl phosphorylcholine (MPC), 2-(methacryloyloxy)ethyltrimethylammonium chloride) (MTAC), and 3-sulfopropyl methacrylate potassium salt (SPMK) were carried out on a silicon wafer and glass ball to prepare polyelectrolyte brushes with excellent water wettability. The frictional coefficient of the polymer brushes was recorded on a ball-on-plate type tribometer by linear reciprocating motion of the brush specimen at a selected velocity of 1.5 x 10(-3) m s-1 under a normal load of 0.49 N applied to the stationary glass ball (d = 10 mm) at 298 K. The poly(DMAEMA-co-MPC) brush partially cross-linked by bis(2-iodoethoxy)ethane maintained a relatively low friction coefficient around 0.13 under humid air (RH > 75%) even after 200 friction cycles. The poly(SPMK) brush revealed an extremely low friction coefficient around 0.01 even after 450 friction cycles. We supposed that the abrasion of the brush was prevented owing to the good affinity of the poly(SPMK) brush for water forming a water lubrication layer, and electrostatic repulsive interactions among the brushes bearing sulfonic acid groups. Furthermore, the poly(SPMK-co-MTAC) brush with a chemically cross-linked structure showed a stable low friction coefficient in water even after 1400 friction cycles under a normal load of 139 MPa, indicating that the cross-linking structure improved the wear resistance of the brush layer.

Anticaries effect of dentifrices with calcium citrate and sodium trimetaphosphate

Directory of Open Access Journals (Sweden)

Alberto Carlos Botazzo Delbem

2012-02-01

Full Text Available Because of the growing concerns regarding fluoride ingestion by young children and dental fluorosis, it is necessary to develop new dentifrices. OBJECTIVE: The aim of this study was to evaluate the effect of dentifrices with calcium citrate (Cacit and sodium trimetaphosphate (TMP on enamel demineralization. MATERIAL AND METHODS: Enamel blocks (n=70, previously selected through surface hardness analysis, were submitted to daily treatment with dentifrices diluted in artificial saliva and to a pH-cycling model. The fluoride concentration in dentifrices was 0, 250, 450, 550, 1,000 and 1,100 µg F/g. CrestTM was used as a positive control (1,100 mg F/g. Cacit (0.25% and TMP (0.25% were added to dentifrices with 450 and 1,000 µg F/g. Surface hardness was measured again and integrated loss of subsurface hardness and fluoride concentration in enamel were calculated. Parametric and correlation tests were used to determine difference (p0.05. CONCLUSIONS: Dentifrices with 450 and 1,000 µg F/g, Cacit and TMP were as effective as a gold standard one.

A double-blind randomized-controlled trial comparing the desensitizing efficacy of a new dentifrice containing carbonate/hydroxyapatite nanocrystals and a sodium fluoride/potassium nitrate dentifrice.

Science.gov (United States)

Orsini, Giovanna; Procaccini, Maurizio; Manzoli, Lamberto; Giuliodori, Francesca; Lorenzini, Alessandro; Putignano, Angelo

2010-06-01

Several dentifrices have shown to be effective in reducing dentine hypersensitivity (DH), but more effective products are needed. The aim of the study was to evaluate the desensitizing efficacy of a new dentifrice based on zinc-carbonate hydroxyapatite (CHA) nanocrystals. Using a double-blind, randomized design, the new dentifrice was compared with potassium nitrate/fluoride dentifrice (active control). The participant's DH was evaluated at baseline and after 4 and 8 weeks using airblast (primary outcome), tactile, cold water and subjective tests (secondary outcomes). The final sample consisted of 70 subjects with baseline DH; 36 received the new dentifrice and 34 the control one. Both dentifrices were largely effective; the percentage of score reduction from baseline to 8 weeks was greater than 28% for all tests (and greater than 55% for the cold water test) in both groups. As compared with controls, experimental subjects had a significantly greater improvement in the airblast test score (mean percentage of reduction of 46.0%versus 29.4% in controls) and the subjective test score (47.5%versus 28.1%, respectively), with both differences already being significant after 4 weeks. In contrast, there was no significant difference between groups for either the tactile or cold water tests at any time point and with any outcome. This study documented that the new dentifrice containing zinc-CHA nanocrystals significantly reduced dentinal hypersensitivity after 4 and 8 weeks, supporting its utility in clinical practice.

Combination effect of fluoride dentifrices and varnish on deciduous enamel demineralization

Directory of Open Access Journals (Sweden)

Alessandra Gatti

2011-10-01

Full Text Available The aim of this study was to evaluate the anticaries potential of 500 or 1100 ppm F dentifrices combined with fluoride varnish using a pH-cycling regimen. Seventy primary canines were covered with nail polish, leaving a 4×4 mm window on their buccal surface, and randomly assigned into 7 groups (n = 10: S: sound enamel not submitted to the pH-cycling regimen or treatment; N: negative control, submitted to the pH-cycling regimen without any treatment; D1 and D2: subjected to the pH-cycling regimen and treated twice daily with 1100 or 500 ppm F dentifrice, respectively; VF: fluoride varnish (subjected to F-varnish before and in the middle of the pH-cycling regimen; and VF+D1 and VF+D2. After 10 days, the teeth were sectioned, and enamel demineralization was assessed by cross-sectional hardness at different distances from the dental surface. Data were analyzed using a two-way ANOVA followed by Tukey's test. Dentifrice with 1100 ppm F and the combination of F-varnish with the dentifrices significantly reduced enamel demineralization compared with the negative control (p 0.05. The effect of combining F-varnish with the dentifrices was not greater than the effect of the dentifrices alone (p < 0.05. The data suggest that the combination of F-varnish with dentifrices containing 500 and 1100 ppm F is not more effective in reducing demineralization in primary teeth than the isolated effect of dentifrice containing 1100 ppm F.

Effect of tooth brushing on gloss retention and surface roughness of five bulk-fill resin composites.

Science.gov (United States)

O'Neill, Catherine; Kreplak, Laurent; Rueggeberg, Frederick A; Labrie, Daniel; Shimokawa, Carlos Alberto Kenji; Price, Richard Bengt

2018-01-01

To determine the effects of tooth brushing on five bulk-fill resin based composites (RBCs). Ten samples of Filtek Supreme Enamel (control), Filtek One Bulk Fill, Tetric EvoCeram Bulk Fill, SonicFill 2, SDR flow+, and Admira Fusion X-tra were light cured for 20 seconds using the Valo Grand curing light. After 24 hours storage in air at 37°C, specimens were brushed in a random order using Colgate OpticWhite dentifrice and a soft toothbrush. Surface gloss was measured prior to brushing, after 5,000, 10,000 and 15,000 back and forth brushing cycles. Surface roughness was measured after 15,000 brushing cycles using atomic force microscopy (AFM) and selected scanning electron microscope (SEM) images were taken. The data was examined using ANOVA and pair-wise comparisons using Scheffe's post-hoc multiple comparison tests (α = 0.05). Surface gloss decreased and the surface roughness increased after brushing. Two-way ANOVA showed that both the RBC and the number of brushing cycles had a significant negative effect on the gloss. One-way ANOVA showed that the RBC had a significant effect on the roughness after 15,000 brushing cycles. For both gloss and roughness, brushing had the least effect on the nano-filled control and nano-filled bulk-fill RBC, and the greatest negative effect on Admira Fusion X-tra. The SEM images provided visual agreement. There was an excellent linear correlation (R 2  = 0.98) between the logarithm of the gloss and roughness. After brushing, the bulk-fill RBCs were all rougher than the control nano-filled RBC. The nano-filled bulk-fill RBC was the least affected by brushing. Bulk-fill RBCs lose their gloss faster and become rougher than the nanofilled conventional RBC, Filtek Supreme Ultra. The nanofilled bulk-fill RBC was the least affected by tooth brushing. © 2017 Wiley Periodicals, Inc.

Effect of nanofillers' size on surface properties after toothbrush abrasion.

Science.gov (United States)

Cavalcante, Larissa M; Masouras, Konstantinos; Watts, David C; Pimenta, Luiz A; Silikas, Nick

2009-02-01

To investigate the effect of filler-particle size of experimental and commercial resin composites, undergoing toothbrush abrasion, on three surface properties: surface roughness (SR), surface gloss (G) and color stability (CS). Four model (Ivoclar/Vivadent) and one commercial resin composite (Tokuyama) with varying filler-size from 100-1000 nm were examined. Six discs (10 mm x 2 mm) from each product were prepared and mechanically polished. The samples were then submitted to 20,000 brushing strokes in a toothbrush abrasion machine. SR parameters (Ra, Rt and RSm), G, and CS were measured before and after toothbrush abrasion. Changes in SR and G were analyzed by 2-way ANOVA, with Bonferroni post hoc test. CS values were submitted to one-way ANOVA and Bonferroni post hoc test (alpha=0.05). Initial G values ranged between 73-87 gloss units (GU) and were reduced after toothbrush abrasion to a range of 8-64 GU. Toothbrush abrasion resulted in significant modifications in SR and G amongst the materials tested, attributed to filler sizes. There was statistically significant difference in color (delta E* ranged from 0.38-0.88). Filler size did not affect color stability. Toothbrush abrasion resulted in rougher and matte surfaces for all materials tested. Although the individual differences in surface roughness among filler sizes were not always significant, the correlation showed a trend that larger filler sizes resulted in higher surface roughness after abrasion for the SR parameters Ra and Rt (r = 0.95; r = 0.93, respectively). RSm showed an increase after toothbrush abrasion for all resin composites, however no significant correlation was detected (r = 0.21).There was a significant correlation between G and Ra ratios (r = - 0.95).

The laboratory and clinical safety evaluation of a dentifrice containing hydrogen peroxide and baking soda.

Science.gov (United States)

Fischman, S L; Truelove, R B; Hart, R; Cancro, L P

1992-01-01

This study reports the laboratory, clinical, and microbiological finding of the safety testing and daily use of a dentifrice delivering 0.75% hydrogen peroxide and 5% baking soda. Laboratory studies using Ca45 labeled teeth and biologically stained teeth confirmed that the dentifrice did not decalcify enamel or bleach teeth. Over the course of a six-month period, 62 subjects using a hydrogen peroxide-baking soda dentifrice and 21 subjects using a control dentifrice were examined for oral soft tissue change and hard tissue alterations. No soft tissue changes attributable to the use of either dentifrice were noted. Experienced clinicians using Trubyte shade guide teeth observed no significant changes to the subjects' anterior teeth following 6 months use of the test dentifrice. Paired discrimination tests revealed that the examiners could distinguish color differences in the shade guide teeth at 0.7%. Microbiological monitoring of the subjects for six months use of their assigned dentifrice and for the following months on the control dentifrice, revealed neither an increased incidence of candida nor increased candida counts.

Dentifrice Containing Extract of Rosmarinus officinalis Linn.: An Antimicrobial Evaluation.

Science.gov (United States)

Valones, Marcela Agne Alves; Higino, Jane Sheila; Souza, Paulo Roberto Eleutério; Crovella, Sérgio; Caldas, Arnaldo de França; Carvalho, Alessandra de Albuquerque Tavares

2016-01-01

This study aimed to evaluate the antimicrobial activity of a dentifrice containing an alcoholic extract of rosemary on oral bacteria, compared to a commercially available herbal dentifrice. Standard strains of Streptococcus mutans (ATCC 25175), Streptococcus oralis (ATCC 9811) and Lactobacillus rhamnosus (ATCC 7469) were used, as well as different toothpastes based on rosemary (TR), on propolis (TH), triclosan (positive control) (TPC) and non-fluoridated dentifrice (negative control) (TNC). Bacteria were seeded in Petri dishes and paper discs soaked with dilutions of dentifrice placed on the plates. The inhibition halos were analyzed. It was observed that TR did not show statistical difference in relation to the TH to inhibit S. mutans and S. oralis, while TH was more active against L. rhamnosus. The toothpaste containing rosemary extract had the ability to inhibit the growth of S. mutans, S. oralis and L. rhamnosus, revealing an antimicrobial activity similar to commercially available toothpastes for inhibition of S. mutans and S. oralis.

Comparative evaluation of effect of use of toothbrush with paste and munident on levels of Streptococcus mutans and gingival health in children: An in vivo study.

Science.gov (United States)

Shetty, Rashmi N; Shetty, Sowmya B; Janardhanan, Sruthi; Shetty, Shamila; Shetty, Sharan; Raj, Kiran

2017-01-01

Dental caries is a multifactorial disease which has a deleterious effect on the oral cavity. Improper oral hygiene habits are a cause for the same. The aim of this study was to compare the antibacterial efficacy of Munident, an Ayurvedic (herbal) dentifrice with commercially available toothpaste. A total of forty subjects between the age group 9 and 12 years, resident of Bala Yeshu Nilaya Bhavan, Mangalore, Karnataka, India, were chosen for our study. They were divided into two groups containing twenty subjects in each; Group 1 for standard toothpaste and Group 2 for Munident. The decayed, missing, and filled teeth scores were noted from each subject. Group 1 was instructed to brush the teeth using commercially available toothpaste and Group 2 was instructed to brush using commercially available Munident (herbal) dentifrice. Both the groups brushed the teeth using soft variety of tooth brush. The gingival bleeding index and salivary Streptococcus mutans count were noted pre- and post-brushimg for both groups. The results obtained were subjected to statistical analysis. Munident (herbal) dentifrice showed better efficacy in comparison to toothpaste in terms of gingival bleeding index and salivary S. mutans count. Munident (herbal) dentifrice has better gingival bleeding index compared to standard formulation of toothpaste. Hence, the practice of using herbal dentifrice should be encouraged.

The Efficacy of Xylitol, Xylitol-Probiotic and Fluoride Dentifrices in Plaque Reduction and Gingival Inflammation in Children: A Randomised Controlled Clinical Trial.

Science.gov (United States)

Arat Maden, Eda; Altun, Ceyhan; Açikel, Cengizhan

The present prospective, randomised, placebo-controlled, clinical trial was designed to evaluate the clinical effects of a commercially available dentifrice containing fluoride, xylitol or xylitol-probiotic on the decrease of plaque and gingival inflammation in children between 13 and 15 years of age. Forty-eight adolescents were randomly grouped into three groups of n = 16 each: study group A received xylitol (Xyliwhite) toothpaste; study group B received xylitol-probiotic (Periobiotic) toothpaste; and the control group C received fluoride (Colgate Max Fresh) toothpaste. The subjects were instructed to use the dentifrice determined and a modified Bass brushing technique twice a day for two minutes over a 6-week perioed. Clinical evaluation was performed using a gingival index and a plaque index at baseline and at the end of the 6-week period. From day 0 to 42, reductions in the plaque index were statistically significant in all groups, Colgate Max Fresh, PerioBiotic and Xyliwhite (p-values 0.001, 0.001 and 0.035, respectively), but reductions in the gingival index were statistically significant only in the Colgate Max Fresh and PerioBiotic groups (both with p = 0.001), not in the Xyliwhite group (p = 0.116). PerioBiotic toothpaste was found to be better than Xyliwhite and Colgate Max Fresh toothpastes at reducing plaque and gingival scores. However, statistically significant differences with PerioBiotic and Colgate Max Fresh toothpaste were not observed. It was concluded that PerioBiotic was an all-round dentifrice that produced a significant reduction in both gingivitis and plaque.

Aloe vera herbal dentifrices for plaque and gingivitis control: a systematic review.

Science.gov (United States)

Dhingra, K

2014-04-01

To evaluate the effectiveness of aloe vera containing herbal dentifrices in improving plaque control and gingival health. A manual and electronic literature (MEDLINE and Cochrane Central Register of Controlled Trials) search was performed up to July 2012, for randomized controlled trials presenting clinical, microbiological, immunological, and patient-centered data for the efficacy of aloe vera herbal dentifrices for controlling plaque and gingival inflammation in patients with gingivitis. From 79 titles and abstracts, eight full-text articles were screened and finally two randomized controlled trials were selected. These randomized controlled trials reported that aloe vera dentifrices were similar in efficacy to control dentifrices in effectively reducing plaque and gingival inflammation in gingivitis patients based on the assessment of clinical, microbiological, and patient-centered treatment outcomes. However, many important details (composition and characteristics of aloe vera and control dentifrices along with appropriate randomization, blinding, and outcomes assessed) were lacking in these trials, and therefore, the quality of reporting and methods was generally flawed with high risk of bias. Even though there are some promising results, the clinical effectiveness of aloe vera herbal dentifrices is not sufficiently defined at present and warrants further investigations based on reporting guidelines of herbal CONSORT statement. © 2013 John Wiley & Sons A/S.

Brushed Target on Rock 'Champagne' in Gusev Crater

Science.gov (United States)

2005-01-01

NASA's Mars Exploration Rover Spirit took this microscopic image of a target called 'Bubbles' on a rock called 'Champagne' after using its rock abrasion tool to brush away a coating of dust. The circular brushed area is about 5 centimeters (2 inches) across. This rock is different from rocks out on the plains of Gusev Crater but is similar to other rocks in this area of the 'Columbia Hills' in that it has higher levels of phosphorus. Plagioclase, a mineral commonly found in igneous rocks, is also present in these rocks, according to analysis with the minature thermal emission spectrometer. By using the alpha particle X-ray spectrometer to collect data over multiple martian days, or sols, scientists are also beginning to get measurements of trace elements in these rocks. Spirit took the images that are combined into this mosaic on sol 354 (Dec. 30, 2004).

High Fluoride Dentifrices for Elderly and Vulnerable Adults

DEFF Research Database (Denmark)

Ekstrand, Kim Rud

2016-01-01

The primary aim of this work is to present the available evidence that toothpastes containing >1,500 ppm fluoride (2,500-2,800 and 5,000 ppm F) provide an additional caries preventive effect on root caries lesions in elderly patients compared to traditional dentifrices (1,000-1,450 ppm F......). The secondary aim of this paper is to discuss why high fluoride dentifrices in general should perform better than traditional F-containing toothpaste. When examining the few studies that have considered the preventive benefits of high fluoride products on root caries the relative risk appears to be around 0.......5, and the risk can thus be halved by exchanging traditional F-containing toothpaste for toothpaste containing 5,000 ppm F. There is reasonable evidence that high fluoride dentifrices significantly increase the fluoride concentration in saliva during the day and the fluoride concentration in plaque compared...

The effect of brushing with nano calcium carbonate and calcium carbonate toothpaste on the surface roughness of nano-ionomer

Science.gov (United States)

Anisja, D. H.; Indrani, D. J.; Herda, E.

2017-08-01

Nanotechnology developments in dentistry have resulted in the development of nano-ionomer, a new restorative material. The surface roughness of restorative materials can increase bacteria adhesion and lead to poor oral hygiene. Abrasive agents in toothpaste can alter tooth and restorative material surfaces. The aim of this study is to identify the effect of brushing with nano calcium carbonate, and calcium carbonate toothpaste on surface roughness of nano-ionomer. Eighteen nano-ionomer specimens were brushed with Aquabidest (doubledistilled water), nano calcium carbonate and calcium carbonate toothpaste. Brushing lasted 30 minutes, and the roughness value (Ra) was measured after each 10 minute segment using a surface roughness tester. The data was analyzed using repeated ANOVA and one-way ANOVA test. The value of nano-ionomer surface roughness increased significantly (p<0.05) after 20 minutes of brushing with the nano calcium carbonate toothpaste. Brushing with calcium carbonate toothpaste leaves nano-ionomer surfaces more rugged than brushing with nano calcium carbonate toothpaste.

Effect of a stannous fluoride dentifrice on the sulcular microbiota: a prospective cohort study in subjects with various levels of periodontal inflammation.

Science.gov (United States)

Benjasupattananan, Supranee; Lai, Caroline S Y; Persson, G Rutger; Pjetursson, Bjarni E; Lang, Niklaus P

2005-01-01

To assess the effects of an experimental 0.454% stannous fluoride (SnF2) dentifrice on the oral sulcular microbiota in patients with various stages of oral diseases using checkerboard DNA-DNA hybridization. In the present one-month, single center, single product, prospective cohort trial, 37 adults (mean age 37.6) were assigned to one of four oral health condition cohorts with seven to 10 subjects each: 1. mild gingivitis, 2. marked generalized gingivitis to moderate periodontitis, 3. caries-prone and 4. treated moderate to advanced chronic periodontitis in supportive periodontal care. All four groups were asked to use the test dentifrice and a power toothbrush twice a day for one minute during a four-week test period. Before and after the trial period, Plaque Indices (PII, Silness and Löe, 1964) and Gingival Indices (GI, Löe and Silness, 1963) were recorded. Subgingival plaque samples were collected from all patients at Baseline, as well as after two and four weeks. These samples were analyzed for content of 40 bacterial species using checkerboard DNA-DNA hybridization. As a result of the only one minute brushing with the stannous fluoride dentifrice, the mean PII at Baseline was significantly lower (p bacterial loads of bacteria than groups 1, and 3 (i.e. A. actinomyctemcomitans P. gingivalis, T. forsythia, and T. denticola. Over the study period, the total bacterial load did not change in groups 2, 3 and 4. In groups 1 and 3, however, an increase in the loads of Streptococci spp. were noticed (p fluoride dentifrice did--after four weeks--not affect the subgingival microbial profiles in patients with moderate periodontitis and treated moderate to advanced periodontitis. However, the sulcular microbial profiles of mild gingivitis and caries-prone patients were affected, indicating a shift towards a gingival health associated microbiota in the sulcular region of patients not affected by attachment loss. RUNNING HEAD: Effect of stannous fluoride on sulcular

Development and assessment of two decontamination processes: closed electropolishing system for decontamination of underwater surfaces -vibratory decontamination with abrasives

International Nuclear Information System (INIS)

Benavides, E.; Fajardo, M.

1992-01-01

Two decontamination processes have been developed to decontaminate the stainless steel components of nuclear power plants. The first process uses an underwater closed electropolishing system for the decontamination of large stainless steel surfaces in flooded systems without loss of electrolyte. Large underwater contaminated areas can be treated with an electropolishing head covering an area of 2 m 2 in one step. The decontamination factors achieved with this technique range between 100 and 1000. The second process consists in the decontamination of nuclear components using vibratory equipment with self-cleaning abrasives generating a minimum quantity of waste. This technique may reach contamination factors similar to those obtained with other abrasive methods (brush abrasion, abrasive blasting, etc...). The obtained decontamination factors range between 5 and 50. Only a small quantity of waste is generated, which is treated and reduced in volume by filtration and evaporation

Whitening dentifrice and tooth surface discolorationa systematic review and meta-analysis

NARCIS (Netherlands)

Soeteman, G. D.; Valkenburg, C.; van der Weijden, G. A.; van Loveren, C.; Bakker, Ewp; Slot, D. E.

2018-01-01

ObjectiveThe aim of this systematic review was to assess the effect of a whitening dentifrice (WDF) relative to a regular dentifrice (RDF) on the reduction of natural extrinsic tooth surface discoloration (ETD). Materials and methodsThe MEDLINE-PubMed, Cochrane-CENTRAL and EBSCO-Dentistry and Oral

Comparative evaluation of effect of use of toothbrush with paste and munident on levels of Streptococcus mutans and gingival health in children: An in vivo study

Directory of Open Access Journals (Sweden)

Rashmi N Shetty

2017-01-01

Full Text Available Aim: Dental caries is a multifactorial disease which has a deleterious effect on the oral cavity. Improper oral hygiene habits are a cause for the same. The aim of this study was to compare the antibacterial efficacy of Munident, an Ayurvedic (herbal dentifrice with commercially available toothpaste. Materials and Methods: A total of forty subjects between the age group 9 and 12 years, resident of Bala Yeshu Nilaya Bhavan, Mangalore, Karnataka, India, were chosen for our study. They were divided into two groups containing twenty subjects in each; Group 1 for standard toothpaste and Group 2 for Munident. The decayed, missing, and filled teeth scores were noted from each subject. Group 1 was instructed to brush the teeth using commercially available toothpaste and Group 2 was instructed to brush using commercially available Munident (herbal dentifrice. Both the groups brushed the teeth using soft variety of tooth brush. The gingival bleeding index and salivary Streptococcus mutans count were noted pre- and post-brushimg for both groups. The results obtained were subjected to statistical analysis. Results: Munident (herbal dentifrice showed better efficacy in comparison to toothpaste in terms of gingival bleeding index and salivary S. mutans count. Conclusion: Munident (herbal dentifrice has better gingival bleeding index compared to standard formulation of toothpaste. Hence, the practice of using herbal dentifrice should be encouraged.

The effect of a fluoride dentifrice containing an anticalculus agent on dental caries in children.

Science.gov (United States)

Lu, K H; Yen, D J; Zacherl, W A; Ruhlman, C D; Sturzenberger, O P; Lehnhoff, R W

1985-01-01

In this double-blind caries study, 1160 Taiwanese children (ages 8-15) completed a program using a test dentifrice containing 1.243 percent sodium fluoride and soluble pyrophosphates, or a control dentifrice without these agents. The average reduction of new carious tooth surfaces was 39 percent with the sodium fluoride dentifrice.

Therapeutic effectiveness of a new enzymatic bleaching dentifrice.

Science.gov (United States)

Forner, Leopaldo; Amengual, José; Liena, Carmen; Riutord, Pere

2012-01-01

Research into bleaching focuses on new products in order to minimize undesirable effects. This study evaluated the bleaching effectiveness of a new enzymatic-activated dentifrice. A total of 20 volunteers were bleached with a dentifrice containing 5% lactoperoxidase and 3% carbamide peroxide applied three times a day for two minutes over 21 days. Color was recorded before and after the treatment using a spectrophotometer. CIELAB differences were calculated before and after treatment using the paired t test (P whitening teeth. Enzymatic dental bleaching is able to increase the efficiency of low concentration peroxides, reducing the potential risk of peroxides on oral tissues.

Whitening dentifrice and tooth surface discoloration : a systematic review and meta-analysis

NARCIS (Netherlands)

Soeteman, G.D.; Valkenburg, C.; van der Weijden, G.A.; van Loveren, C.; Bakker, E.W.P.; Slot, D.E.

2018-01-01

Objective: The aim of this systematic review was to assess the effect of a whitening dentifrice (WDF) relative to a regular dentifrice (RDF) on the reduction of natural extrinsic tooth surface discoloration (ETD). Materials and metods: The MEDLINE-PubMed, Cochrane-CENTRAL and EBSCO-Dentistry and

Loss on drying, calcium concentration and pH of fluoride dentifrices

Directory of Open Access Journals (Sweden)

Arella Cristina Muniz Brito

2015-01-01

Full Text Available Introduction: Fluoride dentifrices containing calcium carbonate have advantages such as control of dental plaque and progression of dental caries, also contributing to oral hygiene, represent most dentifrices marketed in Brazil. Aim: To evaluate the physicochemical properties of seven fluoride dentifrices containing calcium carbonate in relation to hydrogen potential (pH, loss on drying and calcium concentration. Materials and Methods: Data collection was performed using the potentiometric method for pH ranges, gravimetric analysis for loss on drying and atomic absorption spectrometry for the concentration of calcium ions. All tests were performed in triplicate and the analysis was performed entirely at random according to one-way analysis of variance at 5% significance level. Results: The pH values were alkaline and ranged from 8.67 (Oral-B 123® to 10.03 (Colgate Mαxima Proteηγo Anticαries® . The results of loss on drying ranged from 33.81% (Oral-B 123® to 61.13% (Close Up® , with significant differences between brands tested. In relation to the calcium content, the highest and lowest concentrations were found in dentifrices Even® (155.55 g/kg and Colgate Ultra Branco® (129 g/kg, respectively, with significant difference (P < 0.05. Conclusion: Fluoride dentifrices analyzed showed alkaline pH and high levels of loss on drying and calcium concentration. However, these physicochemical characteristics differed according to the different brands tested.

a laboratory evaluation of the efficacy of a herbal dentifrice on dental ...

African Journals Online (AJOL)

Dr Olaleye

Maxam(R). This reduction suggested the inhibitory role the experimental herbal dentifrice Dabur(R) plays in caries development. Keywords: Dental Caries, Dentifrices, Dabur(R), Maxam(R), Caries Scores. INTRODUCTION. Dental Caries (tooth decay) is a disease of insidious onset and its rate of progress is slow in children ...

An Eight-Week Clinical Evaluation of an Oscillating-Rotating Power Toothbrush with a Brush Head Utilizing Angled Bristles Compared with a Sonic Toothbrush in the Reduction of Gingivitis and Plaque.

Science.gov (United States)

Ccahuana-Vasquez, Renzo A; Conde, Erinn; Grender, Julie M; Cunningham, Pamela; Qaqish, Jimmy; Goyal, C Ram

2015-01-01

To evaluate and compare the efficacy of an oscillating-rotating (O-R) power toothbrush with a brush head utilizing angled bristles to a marketed sonic toothbrush in the reduction of plaque and gingivitis over an eight-week period. This study used a randomized, examiner-blind, single-center, two-treatment, parallel group, eight-week design. Subjects with mild-to-moderate plaque and gingivitis were evaluated for baseline whole mouth, gingival margin, and approximal plaque, gingivitis, and gingival bleeding. Clinical assessments were performed using the Modified Gingival Index, Gingival Bleeding Index, and the Rustogi Modified Navy Plaque Index. Subjects received either the O-R brush (Oral-B Professional Care 1000 [D16u] with Oral-B CrossAction brush head [EB50]) or the sonic brush (Sonicare DiamondClean with the standard DiamondClean brush head). Subjects brushed twice daily for two minutes per brushing with the assigned brush and a standard fluoride dentifrice for eight weeks before returning for plaque and gingivitis evaluations using the same methods. Prior to baseline and Week 8 measurements, participants abstained from oral hygiene for 12 hours. One hundred and forty-eight subjects completed the study; 75 in the O-R group and 73 in the sonic group. Both brushes demonstrated statistically significant reductions in plaque and gingivitis over the eight-week study period (p gingivitis than the sonic brush. Whole mouth, gingival margin, and approximal plaque reductions were 27.7%, 46.8%, and 29.3% greater, respectively, compared with the sonic brush, while the reductions in gingivitis, gingival bleeding, and number of bleeding sites were 34.6%, 36.4%, and 36.1% greater, respectively, for the O-R brush than for the sonic brush (p gingivitis reductions for the O-R power brush incorporating the angled-bristled brush head were significantly greater than for the sonic power brush.

Fissure sealants: in vitro evaluation of abrasion wear and superficial roughness

Directory of Open Access Journals (Sweden)

Vanessa Pardi

2008-06-01

Full Text Available The aim of this study was to compare the in vitro wear and superficial roughness of four materials (Delton Dyract Flow, Dentsply; Filtek Flow, Vitremer, 3M ESPE used as fissure sealant in 32 extracted human molars divided in four groups (n = 8 after abrasion with toothbrush/dentifrice. Impressions of each occlusal surface were made to analyze wear and circular specimens were prepared to analyze the roughness. Teeth and specimens were mounted in a toothbrushing machine. The replicas were observed using a SEM to determine the superficial wear. Wear: there were no statistically significant differences either between Delton and Filtek Flow or between Dyract Flow and Vitremer. Roughness: there were no statistical differences between Filtek Flow and Dyract Flow, Dyract Flow and Vitremer, Vitremer and Delton., Considering the clinical practice, if caries activity is present the use of Vitremer is suggested not only for its well known fluoride release, but it presented good roughness results.

Efficacy and mechanisms of non-antibacterial, chemical plaque control by dentifrices--an in vitro study.

Science.gov (United States)

Busscher, Henk J; White, Don J; Atema-Smit, Jelly; van der Mei, Henny C

2007-04-01

The provision of antiplaque benefits to dentifrices assists patients in improving hygiene and reducing susceptibility to gingivitis and caries. Chemical plaque control involves different mechanisms and is mostly associated with antibacterial effects, but also includes effects on pellicle surface chemistry to improve cleansing or discourage renewed plaque formation. It is the aim of this paper to analyze in vitro detachment of co-aggregating oral actinomyces and streptococci from pellicle surfaces by dentifrice supernates and to study subsequent de novo streptococcal deposition. Detachment by dentifrices of a co-adhering bacterial pair was studied in the parallel plate flow chamber on a 16 h pellicle coated surface. After detachment by perfusing the chamber with a dentifrice, re-deposition was initiated by flowing with a fresh streptococcal suspension. The dentifrices included both a regular, SLS-fluoride based formulation as well a pyrophosphate, anticalculus and antimicrobial formulations. All dentifrice supernates containing SLS were effective in detaching co-adhering bacteria from pellicles surfaces, except in combination with SnF(2). When hexametaphosphate was added immediate detachment was relatively low, but continued even during re-deposition. The re-deposition of streptococci after detachment by other, NaF containing dentifrices involved relatively few large aggregates, presumably because fluoride was able to block bi-dentate calcium binding sites on the bacterial cell surfaces, mediating co-adhesion. When pyrophosphate was present in addition to NaF, re-deposition involved significantly more large aggregates, likely because pyrophosphate served as a bi-dentate bridge between calcium bound on the bacterial cell surfaces. Commercially available dentifrice formulations differ in their ability to stimulate bacterial detachment from pellicles and dependent on their composition yield the formation of large co-adhering aggregates of actinomyces and streptococci

Bottle-Brush Brushes: Cylindrical Molecular Brushes of Poly(2-oxazoline) on Glassy Carbon

KAUST Repository

Zhang, Ning; Steenackers, Marin; Luxenhofer, Robert; Jordan, Rainer

2009-01-01

We report on the synthesis of brushes of bottle-brushes of poly(2-oxazoline)s on polished glassy carbon (GC) substrates. First, homogeneous and stable poly(2-isopropenyl-2-oxazoline) (PIPOx) brush layers with thicknesses up to 160 nm were created directly onto GC by the self-initiated photografting and photopolymerization (SIPGP) of 2-isopropenyl-2-oxazoline (IPOx). Kinetic studies reveal a linear increase in thickness with the polymerization time. In a second reaction, the pendant 2-oxazoline ring of the PIPOx brushes were used for the living cationic ring-opening polymerization (LCROP) with different substituted 2-oxazoline monomers to form the side chains. Also for the second surface-initiatedLCROPfrom the surface-bound macroinitiator brushes, the thickness increase with the polymerization time was found to be linear and reproducible. Characterization of the resulting bottle-brush brushes by FTIR spectroscopy,contact angle, and AFM indicates a high side chain grafting density and quantitative reactions. Finally, we have demonstrated the possibility of functionalizing the bottle-brush brushes side chain end groups with sterically demanding molecules. © 2009 American Chemical Society.

Bottle-Brush Brushes: Cylindrical Molecular Brushes of Poly(2-oxazoline) on Glassy Carbon

KAUST Repository

Zhang, Ning

2009-07-28

We report on the synthesis of brushes of bottle-brushes of poly(2-oxazoline)s on polished glassy carbon (GC) substrates. First, homogeneous and stable poly(2-isopropenyl-2-oxazoline) (PIPOx) brush layers with thicknesses up to 160 nm were created directly onto GC by the self-initiated photografting and photopolymerization (SIPGP) of 2-isopropenyl-2-oxazoline (IPOx). Kinetic studies reveal a linear increase in thickness with the polymerization time. In a second reaction, the pendant 2-oxazoline ring of the PIPOx brushes were used for the living cationic ring-opening polymerization (LCROP) with different substituted 2-oxazoline monomers to form the side chains. Also for the second surface-initiatedLCROPfrom the surface-bound macroinitiator brushes, the thickness increase with the polymerization time was found to be linear and reproducible. Characterization of the resulting bottle-brush brushes by FTIR spectroscopy,contact angle, and AFM indicates a high side chain grafting density and quantitative reactions. Finally, we have demonstrated the possibility of functionalizing the bottle-brush brushes side chain end groups with sterically demanding molecules. © 2009 American Chemical Society.

Cleaning, abrasion, and polishing effect of novel perlite toothpaste abrasive.

Science.gov (United States)

Wang, Bo

2013-01-01

This study was intended to optimize perlite particle size and morphology for better tooth cleaning and lower tooth abrasion, and to evaluate the performance of a whitening toothpaste containing the optimized perlite abrasive for tooth cleaning, abrasion, and polishing. Perlite toothpaste abrasive samples were prepared by air classifying a commercial expanded perlite product. The tooth cleaning and abrasion properties for these classified perlite samples were reported via the pellicle cleaning ratio (PCR) and relative dentin abrasion (RDA). Performance of the whitening toothpaste containing the optimized perlite abrasive in tooth cleaning, polishing, and abrasion was evaluated against a widely used synthetic high-cleaning silica. Air classification removes large perlite particles and also physically changes perlite particle morphology from mostly three dimensional and angular particles to mainly two dimensional and platy particles. All the classified samples show good tooth cleaning effect, but tooth abrasion decreases significantly with decreasing particle size. Compared to high-cleaning silica whitening toothpaste, the whitening toothpaste containing the optimized perlite abrasive (PerlClean) is slightly better at tooth cleaning, lower in tooth abrasion, and significantly better at tooth polishing. Fine platy perlite particles are effective in tooth cleaning with low tooth abrasion. The enhanced performance of optimized perlite toothpaste abrasive compared to high-cleaning silica in a whitening toothpaste is attributed to the optimized particle size distribution and the unique platy particle geometry.

Baking soda dentifrice and periodontal health: A review of the literature.

Science.gov (United States)

Sabharwal, Amarpreet; Scannapieco, Frank A

2017-11-01

Mechanical disruption of dental biofilm is critical to maintain periodontal health. Baking soda-containing dentifrices have shown to be potential aids for improving gingival health and maintaining dental biofilm control. Evidence from classic and contemporary literature is reviewed and summarized in this review. In vitro and in vivo (animal and human, respectively) studies and clinical trials have been analyzed. Some clinical studies demonstrated the benefits of baking soda dentifrices in plaque and gingivitis reduction. Clinical trials with longer follow-up would be useful to confirm the impact of baking soda on gingival health. Regular dental biofilm control and adjunctive use of baking soda dentifrices in an otherwise healthy and compliant patient may provide success in maintenance of gingival health. Copyright © 2017 American Dental Association. Published by Elsevier Inc. All rights reserved.

[Influences of composition on brush wear of composite resins. Influences of particle size and content of filler].

Science.gov (United States)

Yuasa, S

1990-07-01

The influences of the composition on abrasion resistance of composite resins were examined using various experimental composite resins which had various matrix resin, filler size and content. The abrasion test was conducted by the experimental toothbrush abrasion testing machine developed in our laboratory. Three series of heat-curing composite resins were tested. One series was made from a Bis-MPEPP or UDMA monomer, and a silica filler with an average particle size of 0.04, 1.9, 3.8, 4.3, 7.5, 13.8 and 14.1 microns. The filler content of this series was constant at 45 wt%. The second series contained a silica filler of 4.3 microns in a content ranging from 35 to 75 wt%. The third series contained a microfiller (0.04 microns) and macrofiller (4.3 microns) in total content of 45 wt%. In this series, the microfiller was gradually replaced by 5, 15, 25 and 45 wt% of the macrofiller. The results obtained for these three series indicated that the abrasion resistance of composite resins was controlled by the inorganic filler, mainly filler size and content. The abrasion loss did not vary with the difference of matrix resin. When the particle size of the filler was below about 5 microns, the abrasion resistance decreased markedly with the decrease in filler size. The composite resin which contained a 0.04 or 1.9 micron filler was less resistant to toothbrush wear than the unfilled matrix resin. However, the microfiller also contributed to abrasion resistance when used in combination with the macrofiller, although abrasion resistance decreased with the increase in the microfiller concentration. The increase of filler content clearly improved the abrasion resistance when used the macrofiller. The analysis of these results and SEM observations of the brushed surfaces of samples suggested that the toothbrush abrasion was three-body abrasion caused by the abrasive in the toothpaste, and affected by the difference in the particle size between abrasive and filler, and between

A randomized 12-week clinical comparison of an oscillating-rotating toothbrush to a new sonic brush in the reduction of gingivitis and plaque.

Science.gov (United States)

Klukowska, M; Grender, J M; Conde, E; Ccahuana-Vasquez, Renzo Alberto; Goyal, C R

2014-01-01

To evaluate the efficacy of a marketed oscillating-rotating (O-R) power toothbrush (Oral-B Triumph with SmartGuide and FlossAction brush head, D34/EB25) to a new sonic toothbrush (Sonicare FlexCare Platinum) in the reduction of gingivitis and plaque over a 12-week test period. This was a single center, randomized, open label, examiner-blind, two-treatment, parallel group study. Subjects who met the entrance criteria were enrolled in the study and randomly assigned to either the O-R or sonic treatment group. Subjects brushed with their assigned toothbrush and a marketed fluoride dentifrice for two minutes twice daily at home for 12 weeks. Gingivitis and plaque were evaluated at Baseline, Week 6, and Week 12. Gingivitis was assessed using the Modified Gingival Index (MGI) and Gingival Bleeding Index (GBI), and plaque was assessed using the Rustogi Modified Navy Plaque Index (RMNPI). Data were analyzed using an Analysis of Covariance (ANCOVA) with Baseline as the covariate. In total, 130 subjects (65 per group) were randomized to treatment and 127 subjects completed the study. Both brushes produced statistically significant (p gingivitis and plaque measures relative to Baseline. At Week 12, the O-R brush demonstrated significantly greater reductions than the sonic brush in whole mouth gingivitis measures (p = 0.007). Additionally, the O-R brush presented significantly fewer bleeding sites (p gingivitis, 19.8% for number of bleeding sites, and 12.2% for whole mouth plaque. There were no adverse events reported or observed for either brush. The oscillating-rotating toothbrush demonstrated statistically significantly greater reductions in whole mouth plaque at Weeks 6 and 12, as well as significantly greater gingivitis reductions over the long-term (12 weeks), compared to the new sonic toothbrush.

Simultaneous Assessment of Acidogenesis-Mitigation and Specific Bacterial Growth-Inhibition by Dentifrices.

Directory of Open Access Journals (Sweden)

Sarah Forbes

Full Text Available Dentifrices can augment oral hygiene by inactivating bacteria and at sub-lethal concentrations may affect bacterial metabolism, potentially inhibiting acidogenesis, the main cause of caries. Reported herein is the development of a rapid method to simultaneously measure group-specific bactericidal and acidogenesis-mitigation effects of dentifrices on oral bacteria. Saliva was incubated aerobically and anaerobically in Tryptone Soya Broth, Wilkins-Chalgren Broth with mucin, or artificial saliva and was exposed to dentifrices containing triclosan/copolymer (TD; sodium fluoride (FD; stannous fluoride and zinc lactate (SFD1; or stannous fluoride, zinc lactate and stannous chloride (SFD2. Minimum inhibitory concentrations (MIC were determined turbidometrically whilst group-specific minimum bactericidal concentrations (MBC were assessed using growth media and conditions selective for total aerobes, total anaerobes, streptococci and Gram-negative anaerobes. Minimum acid neutralization concentration (MNC was defined as the lowest concentration of dentifrice at which acidification was inhibited. Differences between MIC and MNC were calculated and normalized with respect to MIC to derive the combined inhibitory and neutralizing capacity (CINC, a cumulative measure of acidogenesis-mitigation and growth inhibition. The overall rank order for growth inhibition potency (MIC under aerobic and anaerobic conditions was: TD> SFD2> SFD1> FD. Acidogenesis-mitigation (MNC was ordered; TD> FD> SFD2> SFD1. CINC was ordered TD> FD> SFD2> SFD1 aerobically and TD> FD> SFD1> SFD2 anaerobically. With respect to group-specific bactericidal activity, TD generally exhibited the greatest potency, particularly against total aerobes, total anaerobes and streptococci. This approach enables the rapid simultaneous evaluation of acidity mitigation, growth inhibition and specific antimicrobial activity by dentifrices.

Long-term effect of the combined use of powered toothbrush and triclosan dentifrice in periodontal maintenance patients.

Science.gov (United States)

Bogren, Anna; Teles, Ricardo P; Torresyap, Gay; Haffajee, Anne D; Socransky, Sigmund S; Jönsson, Kerstin; Wennström, Jan L

2008-02-01

To test the hypothesis of a superior clinical and microbiological effect of the combined use of powered toothbrush+triclosan-containing dentifrice compared with manual toothbrush+regular fluoride-containing dentifrice in periodontal maintenance patients. A total of 128 periodontitis subjects involved in recall programmes were randomized to use either powered toothbrush with triclosan-dentifrice (test) or manual toothbrush and standard dentifrice (control). Supportive periodontal treatment was provided at baseline and every 6 months. Plaque, bleeding on probing (BoP), probing pocket depth (PPD) and relative attachment level (RAL) were scored at baseline, 1, 2 and 3 years. Subgingival plaque samples were taken and analysed for their content of 40 bacterial species at each examination interval. All analyses were performed by "intention-to-treat" protocol. Both groups showed significant reduction in BoP, PPD and in mean total counts of the 40 bacterial species between baseline and 3 years, while plaque score and RAL remained almost unchanged. No significant differences between the two prevention programmes were found for any of the clinical outcome variables or in mean counts of the various bacterial species. The study failed to demonstrate superior clinical and microbiological effects of powered toothbrush+triclosan dentifrice compared with manual toothbrush+standard fluoride-dentifrice in periodontitis-susceptible patients on regular maintenance therapy.

The stability of water- and fat-soluble vitamin in dentifrices according to pH level and storage type.

Science.gov (United States)

Park, Jung-Eun; Kim, Ki-Eun; Choi, Yong-Jun; Park, Yong-Duk; Kwon, Ha-Jeong

2016-02-01

The purpose of this study is to evaluate the vitamin stabilities in dentifrices by analyzing various vitamins according to the level and storage temperature. The stabilities of water- and fat-soluble vitamins were investigated in buffer solution at different pH values (4, 7, 8, 10 and 11) for 14 days and in dentifrices at different pH (7 and 10) for 5 months at two temperature conditions (room and refrigeration temperature) by analyzing the remaining amounts using HPLC methods. In the buffer solution, the stability of vitamins B1 , B6 and C was increased as the pH values increased. Vitamins E and K showed poor stability at pH 4, and vitamin B3 showed poor stability at pH 11. In dentifrices, the storage temperature highly influenced vitamin stability, especially vitamins C and E, but the stabilities of vitamins B1 and C according to pH values did not correspond to the buffer solution tests. Vitamin B group was relatively stable in dentifrices, but vitamin C completely disappeared after 5 months. Vitamin K showed the least initial preservation rates. Vitamins were not detected in commercial dentifrices for adults and detected amounts were less than the advertised contents in dentifrices for children. Copyright © 2015 John Wiley & Sons, Ltd.

Study of a bland dentifrice for persons with radiation-induced mucositis and vesiculo-erosive disease

International Nuclear Information System (INIS)

Greenspan, D.; Silverman, S. Jr.

1979-01-01

Persons with lesions of the mucous membrane induced by radiation or vesiculo-erosive disease often find commercial dentifrices irritating to the tissues, yet maintenance of their oral hygiene practices is important. A bland monofluorophosphate dentifrice was formulated for use by these persons and tested in a double-blind cross-over study

Effect of oral health education and fluoridated dentifrices on the oral health status of visually impaired children

Directory of Open Access Journals (Sweden)

Sujay Kumar

2012-01-01

Full Text Available Visually impaired children are challenged everyday in their everyday skills. Oral hygiene practices among visually impaired children require a special approach with time and patience. The purpose of this study was to evaluate the effect of oral health education and fluoridated dentifrices on the oral health status of visually impaired children. Materials and Methods: Fifty visually impaired children between 8 and 12 years of age formed the study group. Oral health education and motivation was done with the help of Braille. Modified Bass method of brushing was taught to the children and the required dental treatment was done. Subjects were randomly divided into two equal groups fluoridated and non-fluoridated. Oral hygiene index -simplified, DMFT, deft index, and Streptococcus mutans and Lactobacillus count were assessed at baseline, immediately after the treatment and at 3, 6, and 12 month intervals. The oral health awareness was assessed using a questionnaire at the beginning and end of the study. Results: At baseline, the mean OHI-S, DMFT and deft scores were 2.72, 0.47, and 0.51 respectively. At the end of 12 months there was a significant decrease in OHI-S scores in the fluoridated group. No significant difference was seen in DMFT and deft between the fluoridated and non-fluoridated groups at the different time interval. After the oral health education and comprehensive treatment there was a reduction in Streptococcus mutans and Lactobacillus counts in both groups; however, at the end of 3, 6, 12 months there was a significant decrease in fluoridated group as compared to the non-fluoridated. The oral health awareness increased significantly at the end of the study. Conclusion: The oral health education and motivation formulated for the visually impaired children was effective in improving their oral health status. Fluoridated dentifrices decreased the Streptococcus mutans and Lactobacillus counts and improved the oral hygiene status.

Air Abrasion

Science.gov (United States)

... Chapters What Is Air Abrasion? What Happens? The Pros and Cons Will I Feel Anything? Is Air ... will perform any procedures that use air-abrasion technology. Ask your dentist if he or she uses ...

Randomized clinical study of alterations in the color and surface roughness of dental enamel brushed with whitening toothpaste.

Science.gov (United States)

de Moraes Rego Roselino, Lourenço; Tirapelli, Camila; de Carvalho Panzeri Pires-de-Souza, Fernanda

2018-03-30

This clinical study evaluated the influence of whitening toothpaste on color and surface roughness of dental enamel. Initially, the abrasiveness of the toothpastes used (Sorriso Dentes Brancos [SDB]; Colgate Luminous White and Close up White Now) was tested on 30 (n = 10) plexiglass acrylic plates that were submitted to mechanical tooth brushing totalizing 29,200 cycles. Subsequently, 30 participants were selected, and received a toothbrush and nonwhitening toothpaste (SDB). The participants used these products for 7 days and initial color readouts (Spectrophotometer) and surface roughness of one maxillary central incisors was performed after this period of time. For surface roughness readouts, one replica of the maxillary central incisor was obtained by a polyvinyl siloxane impression material (Express) and polyurethane resin. After baseline measurements, participants were separated into three groups (n = 10), according to the toothpaste used. The participants returned after 7, 30, and 90 days when new color readouts and surface roughness were recorded. The measured values were statistically analyzed (2-way-ANOVA, repeated measures, Tukey, P Whitening toothpastes did not promote significant (P > .05) color alteration and nor increased the surface roughness of the dental enamel in brushing time of the study. The abrasiveness of whitening toothpaste and the brushing trial period did not affect the surface roughness of dental enamel. However, color changes observed on enamel were above the perceptibility and acceptability thresholds reported in the literature. The over-the-counter toothpastes tested had an effect on dental enamel color above the perceptibility and acceptability thresholds but did not change the surface roughness of the teeth. © 2018 Wiley Periodicals, Inc.

Using DGGE and 16S rRNA gene sequence analysis to evaluate changes in oral bacterial composition.

Science.gov (United States)

Chen, Zhou; Trivedi, Harsh M; Chhun, Nok; Barnes, Virginia M; Saxena, Deepak; Xu, Tao; Li, Yihong

2011-01-01

To investigate whether a standard dental prophylaxis followed by tooth brushing with an antibacterial dentifrice will affect the oral bacterial community, as determined by denaturing gradient gel electrophoresis (DGGE) combined with 16S rRNA gene sequence analysis. Twenty-four healthy adults were instructed to brush their teeth using commercial dentifrice for 1 week during a washout period. An initial set of pooled supragingival plaque samples was collected from each participant at baseline (0 h) before prophylaxis treatment. The subjects were given a clinical examination and dental prophylaxis and asked to brush for 1 min with a dentifrice containing 0.3% triclosan, 2.0% PVM/MA copolymer and 0.243% sodium fluoride (Colgate Total). On the following day, a second set of pooled supragingival plaque samples (24 h) was collected. Total bacterial genomic DNA was isolated from the samples. Differences in the microbial composition before and after the prophylactic procedure and tooth brushing were assessed by comparing the DGGE profiles and 16S rRNA gene segments sequence analysis. Two distinct clusters of DGGE profiles were found, suggesting that a shift in the microbial composition had occurred 24 h after the prophylaxis and brushing. A detailed sequencing analysis of 16S rRNA gene segments further identified 6 phyla and 29 genera, including known and unknown bacterial species. Importantly, an increase in bacterial diversity was observed after 24 h, including members of the Streptococcaceae family, Prevotella, Corynebacterium, TM7 and other commensal bacteria. The results suggest that the use of a standard prophylaxis followed by the use of the dentifrice containing 0.3% triclosan, 2.0% PVM/MA copolymer and 0.243% sodium fluoride may promote a healthier composition within the oral bacterial community.

The influence of varnish and high fluoride on erosion and abrasion in a laboratory investigation.

Science.gov (United States)

Sar Sancakli, H; Austin, R S; Al-Saqabi, F; Moazzez, R; Bartlett, D

2015-03-01

The aim of this study was to investigate the potential of concentrated fluoride varnishes to reduce enamel loss from repeated cycles of citric acid erosion and toothbrush abrasion in vitro. Polished human enamel samples were exposed to fluoride varnishes: Bifluorid10® (NaF&CaF2- 45,200 ppmF), Duraphat® (NaF 22,600 ppmF), Fluor-Protector® (difluorsilane 1000 ppmF) and a control coating of copal ether varnish (0 ppmF) group and a deionized water group. For each group of 16 samples, nine cycles of erosion and nine cycles of erosion-abrasion [1 cycle=erosion (0.3% citric acid, pH 3.2, 5 min)+artificial saliva (1 h, pH 7.0)+abrasion (120 linear strokes in artificial saliva from Oral B medium soft brushes 300 g loading]. The change in the enamel surface was evaluated using optical profilometry. Duraphat® and Bifluorid10® applications had a median (IQR) step height of 4.21 um (1.59) and 5.01 um (1.02). This was statistically significantly less than Fluor-Protector® 6.83 um (1.25), copal ether 7.22 um (1.97) and water 7.39 um (1.96) (pDental Association.

Study of the rheological properties and the finishing behavior of abrasive gels in abrasive flow machining

Energy Technology Data Exchange (ETDEWEB)

Wang, A. C.; Liu, C. H.; Liang, K. Z.; Pai, S. H. [Ching Yun University, Taipei (China)

2007-10-15

Abrasive flow machining (AFM) is an effective method to finish the smooth surface in the complex holes. Abrasive media are key elements which dominate the polished results in AFM. But it is hard to develop the machining model of these abrasive gels because of its complicated mechanism. In this research, a non-Newtonian flow is used to set up the abrasive mechanism of the abrasive media in AFM. Power law is a main equation of the non-Newtonian flow to describe the motion of the abrasive media. Viscosities vs. shear rates of different abrasive gels are used to establish the power law in CFD-ACE{sup +} software first. And the working parameters of AFM were applied as input to study the properties of the abrasive gels in AFM. Finally, the relationships between the simulations and the experiments were found. And the abrasive mechanism of the abrasive gels was set up in AFM. The simulated results show that the abrasive gel with high viscosity can entirely deform in the complex hole than the abrasive gel with low viscosity. And the abrasive gel with high viscosity generates a larger shear force than the abrasive gel with low viscosity in the same area. Moreover, the strain rate is seriously changed when the abrasive gel cross over the narrow cross-section of the complex hole. It also means that abrasive gel will produce large finish force in that area. And these results indeed consist with the experiments in AFM.

A six-week clinical evaluation of the plaque and gingivitis efficacy of an oscillating-rotating power toothbrush with a novel brush head utilizing angled CrissCross bristles versus a sonic toothbrush.

Science.gov (United States)

Klukowska, Malgorzata; Grender, Julie M; Conde, Erinn; Goyal, C Ram; Qaqish, J

2014-01-01

To compare the efficacy of an oscillating-rotating power toothbrush with a novel brush head incorporating angled CrissCross bristles (Oral-B Triumph with SmartGuide with Oral-B CrossAction brush head) versus a sonic toothbrush (Sonicare DiamondClean) for plaque and gingivitis reduction over a six-week period. This was a single-center, randomized, examiner-blind, two-treatment, parallel group study involving 65 subjects per group. Subjects presenting with mild-to-moderate gingivitis at Baseline were randomly assigned to either the oscillating-rotating brush or the sonic brush. They were instructed to use their assigned toothbrush and a standard fluoride dentifrice for two minutes twice daily at home for six weeks. Gingivitis and plaque were assessed at Baseline and Week 6 using the Modified Gingival Index (MGI), Gingival Bleeding Index (GBI), and Rustogi Modified Navy Plaque Index (RMNPI). Data were analyzed using an Analysis of Covariance (ANCOVA), with baseline as the covariate. Subjects also completed a consumer perception questionnaire to evaluate their brushing experience. One-hundred and thirty subjects were enrolled in the study and randomized to treatment. Sixty-four subjects per group completed the trial. Both brushes produced statistically significant reductions in gingivitis and plaque measures at Week 6 relative to Baseline (p gingivitis and plaque measures compared to the sonic toothbrush. The benefits for the oscillating-rotating brush over the sonic brush were 32.6% for gingivitis, 35.4% for gingival bleeding, 32% for number of bleeding sites, 22% for whole mouth plaque, 24.2% for gingival margin plaque, and 33.3% for approximal plaque (p gingival margin plaque, where p = 0.018). Analysis of the consumer perception questionnaire results showed subjects using the oscillating-rotating brush rated it higher for overall use experience and key attributes related to cleaning, gentleness, and brush head shape/size versus subjects in the sonic brush group

Toothbrushing with vegetable oil: a clinical and laboratorial analysis Escovação dentária com óleo vegetal: análise clínica e laboratorial

Directory of Open Access Journals (Sweden)

Alciara Alice de Almeida Aguiar

2004-06-01

Full Text Available The dentifrices currently available in the marketplace contain many anticariogenic substances, fluoride and abrasives aimed to better clean the dental surface, remove dental plaque, improve salivary flow and its buffer capacity and reduce colonies of bacteria such as S. mutans, the causative agent of dental caries. The objective of this study was to evaluate the possibility of adequately removing dental plaque using an experimental almond oil dentifrice (Titoil with no abrasives or antiplaque agents. This study was carried out with 80 volunteers, all of them 18-year-old recruits from the military training school of Araçatuba - SP. Saliva sampling and dental plaque disclosing were undertaken both before and after 28 days of toothbrushing with a low abrasive dentifrice (Group 1: 40 volunteers or with Titoil (Group 2: 40 volunteers. Statistical analysis of the results revealed that the experimental dentifrice (Titoil did not interfere with salivary flow and reduced dental plaque more than the low abrasive dentifrice, improved the salivary buffer capacity and decreased salivary S. mutans (Caritest-SM as much as regular dentifrices. It was concluded that if the dental industry replaces abrasive by vegetable oil in dentifrices, these will be more effective in maintaining oral health and will cause less dental abrasion.Os dentifrícios atualmente encontrados no mercado contêm muitas substâncias anticariogênicas, flúor e abrasivos para higienizar melhor as superfícies dentárias, remover a placa dentária, melhorar o fluxo salivar e a capacidade tampão e reduzir as colônias bacterianas, como de S. mutans, agente causador da cárie dentária. O objetivo deste estudo foi avaliar a possibilidade de remover placa adequadamente usando um dentifrício experimental, sem abrasivos nem agentes antiplaca, à base de óleo de amêndoas: Titoil. Foi realizado um estudo com 80 recrutas de 18 anos de idade do Tiro de Guerra de Araçatuba - SP. A coleta de

Relative extrinsic stain removal effectiveness of a new battery-powered toothbrush and a flat trim manual toothbrush.

Science.gov (United States)

Hunt, Sheri A; Bartizek, Robert D

2004-01-01

To evaluate the stain removal efficacy of two different toothbrush designs using a laboratory stained pellicle test with seven different dentifrices. The toothbrushes were a prototype powered toothbrush (Crest SpinBrush Pro Whitening) and an ADA reference manual toothbrush, as a control. The dentifrices used in the study were: Crest Dual Action Whitening (Cool Mint), Crest Extra Whitening with Tartar Control (Clean Mint), Crest MultiCare Whitening (Fresh Mint), Colgate Total, Colgate Total Plus Whitening, Arm & Hammer Advance White with Tartar Control and Rembrandt Plus with Active Dental Peroxide. This was a randomized, parallel group study that examined stain removal with a novel toothbrushing configuration adapted for powered and manual toothbrushes. Stain was scored before and after brushing for two consecutive, 1-minute periods using digital image analysis. The mean change in L* was statistically compared between toothbrushes with ANCOVA. Labial enamel specimens were obtained from bovine permanent incisors and these specimens were subjected to a laboratory staining process until the L* values for the samples were in the range of 35-45. Digital images for CIE L*a*b* analysis were captured using a high-resolution digital camera under standard polarized lighting conditions. Based on the L* values, the enamel specimens were divided into 14 groups of nine specimens each. Baseline L* values ranged from 40.62 to 41.38 for the 14 toothbrush/dentifrice combinations. The change in L* (post-brushing minus baseline), denoted as deltaL*, was calculated for each specimen and the resulting data were subjected to a two-way ANCOVA. Toothbrush type and dentifrice type were the two terms in the model, and baseline L* was the covariate. Pairwise tests were performed on the adjusted means in order to compare the stain removal efficacy of the two toothbrushes for each of the seven dentifrices evaluated. The powered toothbrush resulted in statistically significantly greater delta

Effect of an essential oil-containing dentifrice on dental plaque microbial composition.

Science.gov (United States)

Charles, C H; Vincent, J W; Borycheski, L; Amatnieks, Y; Sarina, M; Qaqish, J; Proskin, H M

2000-09-01

To determine the effect of 6 months use of an essential oil-containing (EO) antiplaque/antigingivitis fluoride dentifrice on the balance of the oral microbial flora and on the emergence of resistant microbial forms by analysis of dental plaque and saliva. The dentifrice essential oils consisted of a fixed combination of thymol, menthol, methyl salicylate, and eucalyptol. An identical fluoride-containing dentifrice without the essential oils served as the control. A subgroup of 66 subjects from a clinical trial population of 321 was randomly selected for characterization of their dental plaque microflora. Saliva was also cultured to monitor for the emergence of opportunistic pathogens. Supragingival plaque and saliva were harvested at baseline, after which subjects received a dental prophylaxis. Subjects were sampled again after 3 and 6 months of product use prior to clinical examination. Plaque was characterized for microbial content by phase contrast microscopy for recognizable cellular morphotypes and by cultivation on nonselective and selective culture media. Determination of the minimum inhibitory concentrations of the test agent against selected Actinomyces and Veillonella isolated bacterial species was conducted at all time points to monitor for the potential development of bacterial resistance. There were no statistically significant differences between the microbial flora obtained from subjects using the essential oil-containing dentifrice and the vehicle control for all parameters and time periods except for the percentage of spirochetes at 6 months and for percentage of "other" microorganisms at 3 months. The EO group exhibited a lower adjusted mean for both parameters. Additionally, there was no evidence of the development of bacterial resistance to the antimicrobial activity of the essential oils or the emergence of opportunistic pathogens.

Reduced abrasion drilling fluid

NARCIS (Netherlands)

2010-01-01

A reduced abrasion drilling fluid system and method of drilling a borehole by circulating the reduced abrasion drilling fluid through the borehole is disclosed. The reduced abrasion drilling fluid comprises a drilling fluid, a first additive and a weighting agent, wherein the weighting agent has a

Reduced abrasion drilling fluid

NARCIS (Netherlands)

2012-01-01

A reduced abrasion drilling fluid system and method of drilling a borehole by circulating the reduced abrasion drilling fluid through the borehole is disclosed. The reduced abrasion drilling fluid comprises a drilling fluid, a first additive and a weighting agent, wherein the weighting agent has a

Synthesis CNTs Particle Based Abrasive Media for Abrasive Flow Machining Process

International Nuclear Information System (INIS)

Kumar, Sonu; Walia, R.S; Dhull, S.; Murtaza, Q.; Tyagi, P. K.

2016-01-01

Abrasive flow machining (AFM) is a modem fine finishing process used for intricate and internal finishing of components or parts. It is based on flowing of viscoelastic abrasive media over the surface to be fine finished. The abrasive media is the important parameter in the AFM process because of its ability to accurately abrade the predefined area along it flow path. In this study, an attempt is made to develop a new abrasive, alumina with Carbon nanotubes (CNTs) in viscoelastic medium. CNT s in house produced through chemical vapour deposition technique and characterize through TEM. Performance evaluation of the new abrasive media is carried out by increasing content of CNT s with fixed extrusion pressure, viscosity of media and media flow rate as process parameters and surface finish improvement and material removal as process responses in AFM setup. Significantly improvement has been observed in material removal and maximum improvement of 100% has been observed in the surface finish on the inner cylindrical surface of the cast iron work piece. (paper)

Machining with abrasives

CERN Document Server

Jackson, Mark J

2011-01-01

Abrasive machining is key to obtaining the desired geometry and surface quality in manufacturing. This book discusses the fundamentals and advances in the abrasive machining processes. It provides a complete overview of developing areas in the field.

Influence of the Relative Enamel Abrasivity (REA) of Toothpastes on the Uptake of KOH-soluble and Structurally Bound Fluoride.

Science.gov (United States)

Elmazi, Valbona; Sener, Beatrice; Attin, Thomas; Imfeld, Thomas; Wegehaupt, Florian J

2015-01-01

To determine the influence of the relative enamel abrasivity (REA) of fluoridated toothpaste on the uptake of KOH-soluble and structurally bound fluoride into enamel. Bovine enamel samples were randomly allocated to 6 groups (n=36 per group). Groups A to C were treated with sodium fluoride (NaF) toothpastes and groups D to F with amine fluoride (AmF) toothpastes (1500 ppm F each). The REA in groups A and D was 2, in groups B and E it was 6 and in groups C and F it was 9. Twice a day, 18 samples of each group were immersed for 2 min in a slurry (toothpaste:artificial saliva=1:3), while the remaining samples were brushed with the respective slurry (2.5 N force; 60 strokes/min; 2 min). All samples were stored at 37°C and 100% humidity. After five days, the amount of KOH-soluble and structurally bound fluoride was determined and statistically compared by Scheffe's post-hoc tests. REA value and mode of application (immersion or brushing) had no significant influence on the amount of either kind of fluoride from NaF toothpastes. Only for the NaF toothpaste with REA 6 was the amount of KOH-soluble fluoride significantly higher after brushing. With AmF toothpastes, KOH-soluble and structurally bound fluoride concentrations were significantly higher when the samples were brushed. Furthermore, in the REA-2 group, the amounts of KOH-soluble fluoride (brushed or immersed) and structurally bound fluoride (brushed) were significantly higher than in the other groups. The REA dependency of KOH-soluble and structurally bound fluoride was found only for the AmF toothpastes. Using AmF toothpaste, the mode of application influenced the uptake of KOH-soluble and structurally bound fluoride into enamel.

The effect of magnesium hydroxide-containing dentifrice using an extrinsic and intrinsic erosion cycling model.

Science.gov (United States)

Passos, Vanara Florêncio; Rodrigues, Lidiany Karla Azevedo; Santiago, Sérgio Lima

2018-02-01

To evaluate, in vitro, the effect of Mg(OH) 2 dentifrice, and the influence of the number of experimental days, on the extrinsic (citric acid -CA) and intrinsic (hydrochloric acid -HCl) enamel erosion models. Human enamel slabs were selected according to surface hardness and randomly assigned to 3 groups (n=9) as follows: non-fluoridated (negative control), NaF (1450ppm F- positive control) and Mg(OH) 2 (2%) dentifrices. The slabs were daily submitted to a 2-h period of pellicle formation and, over a period of 5days, submitted to cycles (3×/day) of erosive challenge (CA 0.05M, pH=3.75 or HCl 0.01M, pH=2 for 30s), treatment (1min -1:3w/w of dentifrice/distilled water) and remineralization (artificial saliva/120min). Enamel changes were determined by surface hardness loss (SHL) for each day and mechanical profilometry analysis. Data were analyzed by two-way ANOVA followed by Tukey's test to % SHL and one-way ANOVA to profilometry (pextrinsic acid erosion as determined by % SHL (pintrinsic model (p=0.295). With regards to surface wear, no statistically significant differences were found among the groups for CA (p=0.225) and HCl (p=0.526). The findings suggest that Mg(OH) 2 dentifrices might protect enamel against slight erosion, but protection was not effective for stronger acid erosion. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of daily fluoride mouth rinsing on enamel erosive/abrasive wear in situ.

Science.gov (United States)

Stenhagen, K R; Hove, L H; Holme, B; Tveit, A B

2013-01-01

It is not known whether application of fluoride agents on enamel results in lasting resistance to erosive/abrasive wear. We investigated if one daily mouth rinse with sodium fluoride (NaF), stannous fluoride (SnF(2)) or titanium tetrafluoride (TiF(4)) solutions protected enamel against erosive/abrasive wear in situ (a paired, randomised and blind study). Sixteen molars were cut into 4 specimens, each with one amalgam filling (measurement reference surface). Two teeth (2 × 4 specimens) were mounted bilaterally (buccal aspects) on acrylic mandibular appliances and worn for 9 days by 8 volunteers. Every morning, the specimens were brushed manually with water (30 s) extra-orally. Then fluoride solutions (0.4% SnF(2) pH 2.5; 0.15% TiF(4) pH 2.1; 0.2% NaF pH 6.5, all 0.05 M F) were applied (2 min). Three of the specimens from each tooth got different treatment, and the fourth served as control. At midday, the specimens were etched for 2 min in 300 ml fresh 0.01 M hydrochloric acid and rinsed in tap water. This etch procedure was repeated in the afternoon. Topographic measurements were performed by a white-light interferometer. Mean surface loss (±SD) for 16 teeth after 9 days was: SnF(2) 1.8 ± 1.9 µm, TiF(4) 3.1 ± 4.8 µm, NaF 26.3 ± 4.7 µm, control 32.3 ± 4.4 µm. Daily rinse with SnF(2), TiF(4) and NaF resulted in 94, 90 and 18% reduction in enamel erosive/abrasive wear, respectively, compared with control (p < 0.05). The superior protective effect of daily rinse with either stannous or titanium tetrafluoride solutions on erosive/abrasive enamel wear is promising. Copyright © 2012 S. Karger AG, Basel.

Appraisal of the remineralizing potential of child formula dentifrices on primary teeth: An i n vitropH cycling model

Directory of Open Access Journals (Sweden)

M Kiranmayi

2015-01-01

Full Text Available Aim: To evaluate the remineralizing potential of child formula dentifrices on primary teeth using an in vitro 7 days pH cycling model. Materials and Methods: Twenty-one primary teeth were placed in demineralizing solution for 96 h to produce artificial carious lesions; then cut longitudinally into 100-150 μm thick sections and randomly assigned to three groups. Sections in Group A were treated with dentifrice containing 458 ppm monofluorophosphate (MFP and sections in Group B with 500 ppm sodium fluoride (NaF. Group C sections were treated with a nonfluoridated dentifrice. Results: Group A (458 ppm MFP and Group B (500 ppm NaF showed significant decrease in lesion depth, whereas Group C (non F showed a significant increase in depth (P ≤ 0.05, paired t-test. Conclusion: Though dentifrices containing 458 ppm MFP and 500 ppm NaF demonstrated remineralization of carious lesions, it was not complete. Therefore, it is also important to emphasize on other preventive methods in the prevention and/or reversal of carious lesions.

Abrasives and possibilities of increase in efficiency of abrasive waterjets

Czech Academy of Sciences Publication Activity Database

Sitek, Libor; Martinec, Petr

2016-01-01

Roč. 9, March 2016 (2016), s. 877-881 ISSN 1805-0476 R&D Projects: GA MŠk(CZ) LO1406; GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : high-speed waterjets * abrasive waterjets * abrasives * garnet * zirconia Subject RIV: JQ - Machines ; Tools http://www.mmscience.eu/content/file/archives/MM_Science_201603.pdf

Clinical effect of a dentifrice containing three kinds of bactericidal ingredients on periodontal disease: a pilot study in patients undergoing supportive periodontal therapy.

Science.gov (United States)

Kita, Daichi; Kinumatsu, Takashi; Yokomizo, Atsushi; Tanaka, Miki; Egawa, Masahiro; Makino-Oi, Asako; Tomita, Sachiyo; Saito, Atsushi

2018-02-09

This study aimed to evaluate clinically the effect of a novel dentifrice containing three kinds of bactericidal ingredients on periodontal disease. This was a single-arm, prospective clinical study that enrolled patients with periodontitis undergoing supportive periodontal therapy. Periodontal examination, microbiological testing of saliva samples, and evaluation of inflammatory markers (IL-1β, IL-6, IL-8, TNF-α) in gingival crevicular fluid were performed. After 4 weeks of the use of test dentifrice, these parameters were re-evaluated. The use of dentifrice was also subjectively evaluated by clinicians and participants. Among 30 participants, there were significant improvements in the periodontal and microbiological parameters, and the level of interleukin-1β in the gingival crevicular fluid, following the use of the test dentifrice. In clinicians' subjective evaluation of the overall usefulness of the dentifrice, 'mild' and 'moderate' improvement accounted for 83% of the total responses. In the participants' subjective evaluation, the majority indicated their experience of the use as favorable. Within the limitations of this study, it is suggested that the progression of periodontal disease during the supportive periodontal therapy can be prevented by the use of the test dentifrice. Trial registration UMIN Clinical Trials Registry (UMIN-CTR) 000023175. Date of formal registration: July 14, 2016 ( https://upload.umin.ac.jp/cgi-open-bin/ctr/ctr_view.cgi?recptno=R000026716 ).

Polymer Brushes

NARCIS (Netherlands)

Vos, de W.M.; Kleijn, J.M.; Keizer, de A.; Cosgrove, T.; Cohen Stuart, M.A.

2010-01-01

A polymer brush can be defined as a dense array of polymers end-attached to an interface that stretch out into the surrounding medium. Polymer brushes have been investigated for the past 30 years and have shown to be an extremely useful tool to control interfacial properties. This review is intended

Biomolecule-functionalized polymer brushes.

Science.gov (United States)

Jiang, Hui; Xu, Fu-Jian

2013-04-21

Functional polymer brushes have been utilized extensively for the immobilization of biomolecules, which is of crucial importance for the development of biosensors and biotechnology. Recent progress in polymerization methods, in particular surface-initiated atom transfer radical polymerization (ATRP), has provided a unique means for the design and synthesis of new biomolecule-functionalized polymer brushes. This current review summarizes such recent research activities. The different preparation strategies for biomolecule immobilization through polymer brush spacers are described in detail. The functional groups of the polymer brushes used for biomolecule immobilization include epoxide, carboxylic acid, hydroxyl, aldehyde, and amine groups. The recent research activities indicate that functional polymer brushes become versatile and powerful spacers for immobilization of various biomolecules to maximize their functionalities. This review also demonstrates that surface-initiated ATRP is used more frequently than other polymerization methods in the designs of new biomolecule-functionalized polymer brushes.

Effect of dentifrice containing fluoride and/or baking soda on enamel demineralization/remineralization: an in situ study.

Science.gov (United States)

Cury, J A; Hashizume, L N; Del Bel Cury, A A; Tabchoury, C P

2001-01-01

The additive effect of baking soda on the anticariogenic effect of fluoride dentifrice is not well established. To evaluate it, a crossover in situ study was done in three phases of 28 days. Volunteers, using acrylic palatal appliances containing four human enamel blocks, two sound (to evaluate demineralization) and two with artificial caries lesions (to evaluate remineralization), took part in this study. During each phase, 10% sucrose solution was dripped (3 times a day) only onto the sound blocks. After 10 min, a slurry of placebo, fluoride (F) or fluoride and baking soda (F+NaHCO(3)) dentifrice was dripped onto all enamel blocks. The results showed a higher F concentration in dental plaque formed during treatment with F+NaHCO(3) than placebo (pbaking soda neither improves nor impairs the effect of F dentifrice on reduction of demineralization and enhancement of remineralization of enamel.

Stratified polymer brushes from microcontact printing of polydopamine initiator on polymer brush surfaces.

Science.gov (United States)

Wei, Qiangbing; Yu, Bo; Wang, Xiaolong; Zhou, Feng

2014-06-01

Stratified polymer brushes are fabricated using microcontact printing (μCP) of initiator integrated polydopamine (PDOPBr) on polymer brush surfaces and the following surface initiated atom transfer radical polymerization (SI-ATRP). It is found that the surface energy, chemically active groups, and the antifouling ability of the polymer brushes affect transfer efficiency and adhesive stability of the polydopamine film. The stickiness of the PDOPBr pattern on polymer brush surfaces is stable enough to perform continuous μCP and SI-ATRP to prepare stratified polymer brushes with a 3D topography, which have broad applications in cell and protein patterning, biosensors, and hybrid surfaces. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cutting concrete with abrasion jet

International Nuclear Information System (INIS)

Yie, G.G.

1982-01-01

Fluidyne Corporation has developed a unique process and apparatus that allow selected abrasives to be introduced into high-speed waterjet to produce abrasive-entrained waterjet that has high material-cutting capabilities, which is termed by Fluidyne as the Abrasion Jet. Such Abrasion Jet has demonstrated capability in cutting hard rock and concrete at a modest pressure of less than 1360 bars (20,000 psi) and a power input of less than 45 kW (60 horsepower). Abrasion Jet cutting of concrete is characterized by its high rate of cutting, flexible operation, good cut quality, and relatively low costs. This paper presents a general description of this technology together with discussions of recent test results and how it could be applied to nuclear decontamination and decommissioning work. 8 references

pH-cycling models for in vitro evaluation of the efficacy of fluoridated dentifrices for caries control: strengths and limitations

Directory of Open Access Journals (Sweden)

Marília Afonso Rabelo Buzalaf

2010-08-01

Full Text Available Despite a plethora of in situ studies and clinical trials evaluating the efficacy of fluoridated dentifrices on caries control, in vitro pH cycling models are still broadly used because they mimic the dynamics of mineral loss and gain involved in caries formation. This paper critically reviews the current literature on existing pH-cycling models for the in vitro evaluation of the efficacy of fluoridated dentifrices for caries control, focusing on their strengths and limitations. A search was undertaken in the MEDLINE electronic journal database using the keywords "pH-cycling", "demineralization", "remineralization", "in vitro", "fluoride", "dentifrice". The primary outcome was the decrease of demineralization or the increase of remineralization as measured by different methods (e.g.: transverse microradiography or tooth fluoride uptake. Inclusion of studies, data extraction and quality assessment were undertaken independently and in duplicate by two members of the review team. Disagreements were solved by discussion and consensus or by a third party. One hundred and sixteen studies were included, of which 42 addressed specifically the comparison of dentifrices using different pH-cycling models. The other studies included meta-analysis or reviews, data about the effect of different fluoride sources on de-remineralization, different methods for analysis de-remineralization and chemical variables and characteristics of dental hard tissues that might have influence on de-remineralization processes. Generally, the studies presented ability to detect known results established by clinical trials, to demonstrate dose-related responses in the fluoride content of the dentifrices, and to provide repeatability and reproducibility between tests. In order to accomplish these features satisfactorily, it is mandatory to take into account the type of substrate and baseline artificial lesion, as well as the adequate response variables and statistical approaches

``Smart'' Surfaces of Polymer Brushes

Science.gov (United States)

Wang, Qiang; Meng, Dong

2009-03-01

``Smart'' surfaces, also known as stimuli-responsive surfaces, can change their properties (e.g., wettability, adhesion, friction, elasticity, and biocompatibility) in response to external stimuli (e.g., temperature, pressure, light, solvent selectivity, ionic strength, type of salt, pH, applied electric field, etc.). In this work, we use numerical self-consistent field calculations to study in detail the structure and stimuli- responses of various polymer brushes, including (1) the thermo- response of PNIPAM brushes in water, (2) solvent-response of uncharged diblock copolymer brushes, and (3) the stimuli- response of charged two-component polymer brushes (including both the binary A/B brushes and diblock copolymer A-B brushes) to ionic strength, pH, and applied electric field. Among the many design parameters (e.g., chain lengths, grafting densities, A-B incompatibility, degree of ionization of charged polymers, etc.) we identify those that strongly affect the surface switchability. Such knowledge is useful to the experimental design of these smart polymer brushes for their applications.

Water Soluble Responsive Polymer Brushes

Directory of Open Access Journals (Sweden)

Andrew J. Parnell

2011-12-01

Full Text Available Responsive polymer brushes possess many interesting properties that enable them to control a range of important interfacial behaviours, including adhesion, wettability, surface adsorption, friction, flow and motility. The ability to design a macromolecular response to a wide variety of external stimuli makes polymer brushes an exciting class of functional materials, and has been made possible by advances in modern controlled polymerization techniques. In this review we discuss the physics of polymer brush response along with a summary of the techniques used in their synthesis. We then review the various stimuli that can be used to switch brush conformation; temperature, solvent quality, pH and ionic strength as well as the relatively new area of electric field actuation We discuss examples of devices that utilise brush conformational change, before highlighting other potential applications of responsive brushes in real world devices.

Abrasion Properties of Steel Fiber Reinforced Silica Fume Concrete According to Los Angeles and Water Abrasion Tests

Directory of Open Access Journals (Sweden)

Tsan-Ching CHENG

2014-12-01

Full Text Available The current study mainly investigated the influence of different tests on the abrasion resistance of concrete mixed with steel fibers and silica fume. The abrasion resistance was assessed at 28, 56 and 91 days on concretes with water-binder ratios of 0.35 and 0.55 where in some mixes silica fume was substituted by 5 % of cement by weight. Steel fibers of 0.5 % and 1.0 % of concrete volume were also added into the test concrete by replacement of coarse and fine aggregates. The results showed that concrete with higher compressive strength in Los Angeles abrasion tests also had better abrasion resistance. The inclusion of steel fibers into test concrete with a water-binder ratio of 0.35 resulted in a significant increase in compressive strength. This concrete also displayed better abrasion resistance and splitting tensile strength than reference concrete; in the test sample with a water-binder ratio of 0.55, the added steel fibers was unable to effectively produce cementation with the concrete. The inclusion of silica fume improved the abrasion resistance of concretes. In water abrasion testing, the abrasion resistance of concrete containing steel fiber was worse than that of concrete without steel fibers. In the water abrasion testing, the surface of steel fiber reinforced concrete was eroded by water and steel balls, and the impact caused the steel fibers to separate from the concrete and led to higher wear loss. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6460

Usage of abrasion-resistant materials in agriculture

Directory of Open Access Journals (Sweden)

J Votava

2014-06-01

Full Text Available Agricultural soil-processing machines are subject to an extensive abrasive wear. This paper analyses technical materials and their fitness to exchangeable parts of plough bottoms, such as edge-tools and whole plough cutting edges. There were tested abrasion-resistant steels with different microstructures: austenite, martensite-bainite, and carbide. Steel with the pearlite-ferrite structure was used as an etalon. Abrasion resistance tests were processed in compliance with the norm CSN 01 5084, which is a test of abrasion wear on abrasive cloth.

Sustainability of abrasive processes

DEFF Research Database (Denmark)

Aurich, J.C.; Linke, B.; Hauschild, Michael Zwicky

2013-01-01

, the content of technical presentations in STC G, and the results of a comprehensive literature study. The approach to sustainability includes environmental, social, and economic sustainability in accordance with the definition proposed in the Brundtland Report of the United Nations [156]. The main focus......This paper presents an overview of research on sustainability of abrasive processes. It incorporates results from a round robin study on ‘‘energy-efficiency of abrasive processes’’ which has been carried out within the scientific technical committee ‘‘abrasive processes’’ (STC G) of CIRP...... is on environmental and social sustainability. Economic sustainability will be considered as manufacturing productivity. © 2013 CIRP....

Effect of different frequencies of fluoride dentifrice and mouthrinse administration: an in situ study

Directory of Open Access Journals (Sweden)

Daniela Correia Cavalcante Souza

2010-12-01

Full Text Available The effect of a combination of topical fluoridation methods for inhibition of enamel demineralization in the face of a cariogenic challenge has not been clearly established. This in situ crossover study aimed to assess whether the addition of daily use of fluoride mouthrinse (FR to that of fluoride dentifrice (FD is equivalent to increasing the frequency of FD application in terms of the effect on enamel demineralization and fluoride content. Over 3 phases of 14 days each, 12 volunteers wore appliances containing enamel blocks exposed to a 20 % sucrose solution 8 times/day. During each phase the blocks underwent one of the following treatments: 2x/day FD, 2x/day FD + 1x/day FR, and 3x/day FD. The blocks were assessed for hardness and fluoride content. Three x/day FD did not differ from 2x/day + 1x/day FR, however it enhanced demineralization protection when compared to 2x/day FD. All treatments produced an increase in enamel fluoride content compared to no treatment (sound blocks (p < 0.05, but the differences between them were not significant. The results of this study suggest that the daily use of fluoride mouthrinse combined with that of fluoride dentifrice has similar effects on enamel demineralization and fluoride content when compared to increasing the frequency of fluoride dentifrice use.

Progress in abrasive and grinding technology

CERN Document Server

Xu, Xipeng

2009-01-01

The grinding and abrasive processing of materials are machining techniques which use bonded or loose abrasives to remove material from workpieces. Due to the well-known advantages of grinding and abrasive processes, advances in abrasive and grinding technology are always of great import in enhancing both productivity and component quality. In order to highlight the recent progress made in this field, the editor invited 21 world-wide contributions with the aim of gathering together all of the achievements of leading researchers into a single publication. The authors of the 21 invited papers, of

Brush head composition, wear profile, and cleaning efficacy: an assessment of three electric brush heads using in vitro methods.

Science.gov (United States)

Kaiser, Eva; Meyners, Michael; Markgraf, Dirk; Stoerkel, Ulrich; von Koppenfels, Roxana; Adam, Ralf; Soukup, Martin; Wehrbein, Heinrich; Erbe, Christina

2014-01-01

The objective of this research was to evaluate a current store brand (SB) brush head for composition/physical characteristics, Wear Index (WI), and cleaning efficacy versus the previous SB brush head refill design (SB control) and the Oral-B Precision Clean brush head (positive control, PC). This research consisted of three parts: 1) Analytical analysis using Fourier Transform Infrared (FT-IR) spectrometry to evaluate the chemical composition of the current SB brush head bristles relative to the SB control. In addition, physical parameters such as bristle count and diameter were determined. 2) Wear Index (WI) investigation to determine the Wear Index scores of in vitro-aged brush heads at four weeks (one month) and 13 weeks (three months) by a trained investigator. To "age" the brush heads, a robot system was used as a new alternative in vitro method to simulate aging by consumer use. 3) Robot testing to determine the cleaning performance of in vitro-aged brush heads, comparing one month-aged current SB brush heads with the SB control (one and three months-aged) and the PC brush heads (three months-aged) in a standardized fashion. 1) FT-IR analysis revealed that the chemical composition of the current and control SB refill brush heads is identical. In terms of physical parameters, the current SB brush head has 12% more bristles and a slightly oval brush head compared to the round brush head of the SB control. 2) Wear Index analysis showed there was no difference in the one month-aged current SB brush head versus the one month-aged SB control (1.67 vs. 1.50, p = 0.65) or versus the three months-aged PC brush head (1.67 vs. 1.50, p = 0.65). The one month-aged current SB brush head demonstrated statistically significantly less wear than the three months-aged SB control (1.67 vs. 2.67, p = 0.01). 3) Analysis of cleaning efficacy shows that the one month-aged current SB brush head had improved cleaning performance over the one month-aged SB control brush head (p < 0

Properties, structure and machnining capabilities sintered corundum abrasives

Directory of Open Access Journals (Sweden)

Cz.J. Niżankowski

2010-07-01

Full Text Available The diversity of sintered corundum abrasives used in both bonded and in the embankment of abrasive tools currently poses substantialproblems for their choice of technology to specific tasks. Therefore performed a comparative study of ownership structures and capacitiesof elected representatives machnining sintered corundum abrasives of different generations, and this is normal sintered alumina,submicrocrystalline alumina sintered and nanocrystalline alumina sintered. Were studied some properties of a set of abrasive particles,physicochemical properties and structural and mechanical and technological properties. The studies used the method of microscopicmeasurement to determine the shape of abrasive particles, the pycnometer to determine the density of abrasive, a spectrometer todetermine the chemical composition of the magnetic analyzer for determining the magnetic fraction, scanning electron microscope toanalysis of abrasive grains and a special position to designate the machining capacity abrasive grains. The results showed a significantincrease in machining capacity sintered corundum abrasives with increasing degree of fragmentation of the crystallites sintered corundum abrasives and distinctive bands in the emerging microchip. The originality of the development provides a comparative summary ofproperties of sintered corundum abrasives of different generations and functions obtained by the author making the change in value indexof machininhcapacity grit from cutting speeds for different generations of sintered corundum.

AFM-based force spectroscopy on polystyrene brushes: effect of brush thickness on protein adsorption.

Science.gov (United States)

Hentschel, Carsten; Wagner, Hendrik; Smiatek, Jens; Heuer, Andreas; Fuchs, Harald; Zhang, Xi; Studer, Armido; Chi, Lifeng

2013-02-12

Herein we present a study on nonspecific binding of proteins at highly dense packed hydrophobic polystyrene brushes. In this context, an atomic force microscopy tip was functionalized with concanavalin A to perform single-molecule force spectroscopy measurements on polystyrene brushes with thicknesses of 10 and 60 nm, respectively. Polystyrene brushes with thickness of 10 nm show an almost two times stronger protein adsorption than brushes with a thickness of 60 nm: 72 pN for the thinner and 38 pN for the thicker layer, which is in qualitative agreement with protein adsorption studies conducted macroscopically by fluorescence microscopy.

Effects of an ascorbic acid-derivative dentifrice in patients with gingivitis: a double-masked, randomized, controlled clinical trial.

Science.gov (United States)

Shimabukuro, Yoshio; Nakayama, Yohei; Ogata, Yorimasa; Tamazawa, Kaoru; Shimauchi, Hidetoshi; Nishida, Tetsuya; Ito, Koichi; Chikazawa, Takashi; Kataoka, Shinsuke; Murakami, Shinya

2015-01-01

Reactive oxygen species might be associated with the onset and progression of gingival inflammation. The aim of this study is to investigate the effect of a dentifrice containing L-ascorbic acid 2-phosphate magnesium salt (APM), a long-acting ascorbic acid derivative with antioxidant properties, on gingival inflammation. The clinical effects of APM were investigated in a multicenter, randomized, parallel-group, controlled clinical trial comprising 300 individuals with gingivitis. Half of the participants were given an APM-containing dentifrice and half were given a control dentifrice. The primary outcome was the gingival index (GI) at 3 months. Secondary outcomes included gingival redness as an indicator of the degree of local gingival inflammation, gingival bleeding as a measure of the gingivitis severity index, and total antioxidant activity of the saliva. Under the intent-to-treat analysis, GI did not significantly differ between the groups (P = 0.12). However, under the per-protocol analysis, GI was significantly lower in the APM group (P = 0.01) than in the control group. In the APM group, gingival redness was significantly lower, and the difference from the baseline gingivitis severity index was significantly greater (P = 0.04 and P = 0.02, respectively). The total antioxidant activity of the saliva was significantly higher in the APM group (P = 0.03). The incidence of adverse events did not significantly differ between the groups (P > 0.15). These findings indicate that the regular application of an APM-containing dentifrice could reduce gingival inflammation.

The effect of CO2 laser irradiation plus fluoride dentifrice on the inhibition of secondary caries on root surfaces adjacent to glass ionomer cement or composite resin restorations

International Nuclear Information System (INIS)

Rodrigues, S R; Moraes, M; Youssef, M N; De Souza-Zaroni, W C; Hanashiro, F S; Brugnera Junior, A; Nobre-dos-Santos, M

2016-01-01

Although the cariostatic effects of CO 2 laser on the root surface have been shown, there is scarce information regarding its effects on root secondary caries. The objective of this research was to investigate the effect of the association of CO 2 laser and a fluoride dentifrice on the inhibition of secondary caries on root surfaces adjacent to composite-resin or glass-ionomer-cement restorations. Dental blocks of human roots were divided into two groups: composite resin (CR) or glass ionomer cement (GIC). Subsequently, the blocks were divided into four subgroups (n  =  10): C, non-fluoride dentifrice; FD, fluoride dentifrice; L, CO 2 laser with an energy density of 6.0 J cm −2   +  non-fluoride dentifrice; and L  +  FD, CO 2 laser  +  fluoride dentifrice. The blocks were subjected to pH cycling to simulate a high cariogenic challenge. Dental demineralization around the restorations was quantified by microhardness analysis. The results were subjected to analysis of variance (ANOVA) and the Tukey–Kramer test (p  ⩽  0.05). As for mineral loss, it can be observed that all the groups that were treated with a fluoride dentifrice and laser, used alone or not, were statistically similar and superior to the RC–C group. It was concluded that CO 2 laser irradiation and a fluoride dentifrice used alone or combined with each other are efficient surface treatments for preventing secondary root caries, regardless of the restorative material used. (paper)

A double blind randomised controlled clinical trial comparing a novel anti-stain and calculus reducing dentifrice with a standard fluoride dentifrice.

Science.gov (United States)

Jowett, Adrian K; Marlow, Ian; Rawlinson, Andrew

2013-04-01

This clinical trial tested the anti-stain efficacy at 3 and 6 months of a novel, sodium polyaspartate-containing, anti-stain dentifrice. In addition, the efficacy of the new dentifrice in controlling gingival inflammation and inhibition of calculus deposition was tested. Participants were recruited to this double blind randomised control clinical trial, and allocated to either test or control groups. The presence of stain and calculus were entry criteria. Measurements of stain, calculus and gingival inflammation were recorded using the Shaw and Murray Stain score, Volpe-Manhold Calculus score and the Modified Gingival Index respectively. Measurements were made at baseline, prior to the removal of stain and calculus, and after 3 and 6 months. Missing data were imputed by and the outcomes were analysed using univariate analysis. At three months, toothpaste containing sodium polyaspartate was better (difference of mean 1.13 with SEM 0.57) than control for the control of dental stain (p0.05). There was no difference between toothpastes with respect to calculus deposition or gingival inflammation. Toothpaste containing sodium polyaspartate was more effective than a control toothpaste at preventing deposition of dental stain for 3 months after professional tooth cleaning but showed no significant effect at 6 months. Sodium polyaspartate toothpaste was more effective than a control toothpaste at preventing dental stain formation and maybe helpful in controlling staining between episodes of scaling and polishing. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effectiveness of a baking soda toothpaste delivering calcium and phosphate in reducing dentinal hypersensitivity.

Science.gov (United States)

Ghassemi, A; Hooper, W; Winston, A E; Sowinski, J; Bowman, J; Sharma, N

2009-01-01

The purpose of this controlled clinical trial was to determine the effectiveness and safety of a single-phase dentifrice that delivers calcium, phosphate, and fluoride to the tooth surface (Arm & Hammer Enamel Care for Sensitive Teeth toothpaste, United Kingdom) in reducing dentinal hypersensitivity. Two-hundred and eight qualifying subjects were randomly assigned to either the Enamel Care dentifrice group or a control dentifrice group, and brushed twice daily with their assigned dentifrice for eight weeks. Pain/discomfort in response to a thermal stimulus was assessed at baseline, week 4, and week 8 using a Visual Analogue Scale (VAS; primary outcome variable) and the Schiff Thermal Sensitivity Scale (STSS; secondary outcome variable). After eight weeks, volunteers from the Enamel Care group were switched to the control dentifrice and participated in a second eight-week study to determine the degree of persistence of pain reduction. Both groups had statistically significant VAS score reductions from baseline at weeks 4 and 8, with mean VAS scores in the Enamel Care group decreasing by 45.6% at week 4 and 61.1% at week 8 (p < 0.0001). Enamel Care was statistically significantly more effective than the control at weeks 4 and 8, with respective mean VAS reductions of 63% (p < 0.0001) and 33% (p = 0.0004) greater than the control. Consistent with the VAS score results, the Enamel Care group had respective statistically significant STSS score reductions of 77% and 58% greater than the control group (p < 0.0001). The reductions in dentinal hypersensitivity seen in the Enamel Care group at week 8 persisted for an additional eight weeks, during which the subjects discontinued use of Enamel Care and brushed with the control dentifrice. Enamel Care for Sensitive Teeth toothpaste (United Kingdom) is an effective dentifrice for the management of dentinal hypersensitivity, and its efficacy persists for a least eight weeks following discontinued product use.

Titanium surface topography after brushing with fluoride and fluoride-free toothpaste simulating 10 years of use.

Science.gov (United States)

Fais, Laiza M G; Fernandes-Filho, Romeu B; Pereira-da-Silva, Marcelo A; Vaz, Luis G; Adabo, Gelson L

2012-04-01

) does not affect titanium per se; their use during brushing affects titanium topography and roughness. The associated effects of toothpaste abrasives and fluorides seem to increase roughness on titanium brushed surfaces. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effectiveness of low cost toothbrushes, with or without dentifrice, in the removal of bacterial plaque in deciduous teeth

Directory of Open Access Journals (Sweden)

Parizotto Symonne Pimentel Castro de Oliveira Lima

2003-01-01

Full Text Available The main objective of this study was to compare the effectiveness of a low cost toothbrush ("monoblock" to that of a conventional toothbrush with and without addition of dentifrice with respect to the removal of dental plaque. Thirty-two 4- to 6-year-old children took part in this study: they were evaluated under four experimental conditions defined by the combinations of the values of two factors, toothbrush (conventional or monoblock and use of dentifrice (with or without. The effectiveness of the treatments was defined in terms of the reduction of a bacterial plaque index evaluated before and after toothbrushing. No statistically significant differences were detected between the two types of toothbrushes with respect to the reduction of the bacterial plaque index. Similarly, there were no statistical evidences that the use of dentifrice improves the mechanical control of dental plaque. These results are important from a public health point of view, specially in developing countries, where the dissemination of educational and preventive techniques of low cost are fundamental.

A laboratory evaluation of the efficacy of a herbal dentifrice on dental ...

African Journals Online (AJOL)

The efficacy of a topically applied herbal dentifrice (toothpaste) Dabur (R) was evaluated in thirty albino rats. Dental caries was induced by inoculating their mouths with Streptococcus viridans and then fed a cariogenic 56% sucrose sugar in addition to rat pellets. The animals were then divided into 3 equal groups with 10 ...

Antifouling Properties of Fluoropolymer Brushes toward Organic Polymers: The Influence of Composition, Thickness, Brush Architecture, and Annealing.

Science.gov (United States)

Wang, Zhanhua; Zuilhof, Han

2016-07-05

Fluoropolymer brushes are widely used to prevent nonspecific adsorption of commercial polymeric or biological materials due to their strongly hydrophobic character. Herein, a series of fluoropolymer brushes with different compositions, thicknesses and molecular architectures was prepared via surface-initiated atom transfer radical polymerization (ATRP). Subsequently, the antifouling properties of these fluoropolymer brushes against organic polymers were studied in detail using X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) measurements and polystyrene as a representative fouling polymer. Among all of the molecular architectures studied, homopolymerized methacrylate-based fluoropolymer brushes (PMAF17) show the best antifouling properties. Annealing the fluoropolymer brushes improves the antifouling property dramatically due to the reregulated surface composition. These fluoropolymer brushes can be combined with, e.g., micro- and nanostructuring and other advanced materials properties to yield even better long-term antifouling behavior under harsh environments.

Study on design of light-weight super-abrasive wheel

Science.gov (United States)

Nohara, K.; Yanagihara, K.; Ogawa, M.

2018-01-01

Fixed-abrasive tool, also called a grinding wheel, is produced by furnacing abrasive compound which contains abrasive grains and binding powder such as vitrified materials or resins. Fixed-abrasive tool is installed on spindle of grinding machine. And it is given 1,800-2,000 min-1 of spindle rotation for the usage. The centrifugal fracture of the compound of fixed- abrasive tool is one of the careful respects in designing. In recent years, however, super-abrasive wheel as a fixed-abrasive tool has been developed and applied widely. One of the most characteristic respects is that metal is applied for the body of grinding-wheel. The strength to hold abrasive grain and the rigidity of wheel become stronger than those of general grinding wheel, also the lifespan of fixed-abrasive tool becomes longer. The weight of fixed-abrasive tool, however, becomes heavier. Therefore, when the super-abrasive wheel is used, the power consumption of spindle motor becomes larger. It also becomes difficult for the grinding-wheel to respond to sudden acceleration or deceleration. Thus, in order to reduce power consumption in grinding and to obtain quicker frequency response of super-abrasive wheel, the new wheel design is proposed. The design accomplishes 46% weight reduction. Acceleration that is one second quicker than that of conventional grinding wheel is obtained.

Slow brushing reduces heat pain in humans.

Science.gov (United States)

Liljencrantz, J; Strigo, I; Ellingsen, D M; Krämer, H H; Lundblad, L C; Nagi, S S; Leknes, S; Olausson, H

2017-08-01

C-tactile (CT) afferents are unmyelinated low-threshold mechanoreceptors optimized for signalling affective, gentle touch. In three separate psychophysical experiments, we examined the contribution of CT afferents to pain modulation. In total, 44 healthy volunteers experienced heat pain and CT optimal (slow brushing) and CT sub-optimal (fast brushing or vibration) stimuli. Three different experimental paradigms were used: Concurrent application of heat pain and tactile (slow brushing or vibration) stimulation; Slow brushing, applied for variable duration and intervals, preceding heat pain; Slow versus fast brushing preceding heat pain. Slow brushing was effective in reducing pain, whereas fast brushing or vibration was not. The reduction in pain was significant not only when the CT optimal touch was applied simultaneously with the painful stimulus but also when the two stimuli were separated in time. For subsequent stimulation, the pain reduction was more pronounced for a shorter time interval between brushing and pain. Likewise, the effect was more robust when pain was preceded by a longer duration of brush stimulation. Strong CT-related pain reduction was associated with low anxiety and high calmness scores obtained by a state anxiety questionnaire. Slow brushing - optimal for CT activation - is effective in reducing pain from cutaneous heating. The precise mechanisms for the pain relief are as yet unknown but possible mechanisms include inhibition of nociceptive projection neurons at the level of the dorsal horn as well as analgesia through cortical mechanisms. Slow brushing stimuli - optimal for activation of C-tactile fibres - can reduce pain from cutaneous heating. No such effect was seen with fast brushing or vibration. These observations indicate the role of C-tactile fibres in pain modulation. © 2017 European Pain Federation - EFIC®.

The motivational benefits of a dentifrice containing baking soda and hydrogen peroxide.

Science.gov (United States)

Fischman, S L; Kugel, G; Truelove, R B; Nelson, B J; Cancro, L P

1992-01-01

Twenty-two family practice dentists, in a large metropolitan area, were recruited to act as independent examiners in a study to evaluate the compliance of their patients to accept a good oral hygiene regimen with the use of a fluoride dentifrice, containing hydrogen peroxide and baking soda, dispensed from a dual dispensing package. To evaluate compliance, the dentists attended an orientation seminar and were trained to assess gingival health using the CPITN periodontal probe. Each dentist evaluated the gingival health status of five to seven of his own patients, initially and after one and three months of product use following hygiene instruction and product assignment. One-hundred and thirty-one patients successfully completed the study. After one month of using the hydrogen peroxide/baking soda toothpaste, the mean reduction in bleeding sites was 53%; at three months the reduction was 62%. The hydrogen peroxide/baking soda dentifrice was well accepted by dentist and patient, and a discernible improvement in oral health of the patients was achieved when the product was used in a conscientious oral hygiene program.

Abrasive water jets for controlled demolition and dismantling

International Nuclear Information System (INIS)

Abudaka, M.; Crofton, P.S.J.

1988-01-01

Abrasive water jets offer an efficient high speed cutting tool for hard materials such as reinforced concrete, tool steel and armour plate. Cutting by abrasive water jets is often described as a cold cutting operation since no heat is developed and any increase in local temperature is immediately cooled by the water jet. Moreover no sparks are generated to ignite a potentially inflammable atmosphere. Mass flow rates of water and abrasive are small (typically 4 litres/min.water and 1 kg/min abrasive) and hence are easy to collect and to dispose of. For these reasons abrasive water jets offer certain advantages in cutting difficult materials in hazardous environments such as in the nuclear industry, offshore oil rigs and petrochemical plant. Available portable cutting systems are described and the advantages of using abrasive water jets are discussed as well as some of the parameters involved in the cutting operation. Finally a description is presented of some typical applications of abrasive water jet cutting. (author)

Ceramic-bonded abrasive grinding tools

Science.gov (United States)

Holcombe, Jr., Cressie E.; Gorin, Andrew H.; Seals, Roland D.

1994-01-01

Abrasive grains such as boron carbide, silicon carbide, alumina, diamond, cubic boron nitride, and mullite are combined with a cement primarily comprised of zinc oxide and a reactive liquid setting agent and solidified into abrasive grinding tools. Such grinding tools are particularly suitable for grinding and polishing stone, such as marble and granite.

Ceramic-bonded abrasive grinding tools

Science.gov (United States)

Holcombe, C.E. Jr.; Gorin, A.H.; Seals, R.D.

1994-11-22

Abrasive grains such as boron carbide, silicon carbide, alumina, diamond, cubic boron nitride, and mullite are combined with a cement primarily comprised of zinc oxide and a reactive liquid setting agent and solidified into abrasive grinding tools. Such grinding tools are particularly suitable for grinding and polishing stone, such as marble and granite.

Determination of vibration frequency depending on abrasive mass flow rate during abrasive water jet cutting

Czech Academy of Sciences Publication Activity Database

Hreha, P.; Radvanská, A.; Hloch, Sergej; Peržel, V.; Krolczyk, G.; Monková, K.

2014-01-01

Roč. 77, 1-4 (2014), s. 763-774 ISSN 0268-3768 Institutional support: RVO:68145535 Keywords : Abrasive water jet * Abrasive mass flow rate * Vibration Subject RIV: JQ - Machines ; Tools Impact factor: 1.458, year: 2014 http://link.springer.com/article/10.1007%2Fs00170-014-6497-9#page-1

Stimuli-Responsive Polyelectrolyte Brushes As a Matrix for the Attachment of Gold Nanoparticles: The Effect of Brush Thickness on Particle Distribution

Directory of Open Access Journals (Sweden)

Stephanie Christau

2014-06-01

Full Text Available The effect of brush thickness on the loading of gold nanoparticles (AuNPs within stimuli-responsive poly-(N,N-(dimethylamino ethyl methacrylate (PDMAEMA polyelectrolyte brushes is reported. Atom transfer radical polymerization (ATRP was used to grow polymer brushes via a “grafting from” approach. The brush thickness was tuned by varying the polymerization time. Using a new type of sealed reactor, thick brushes were synthesized. A systematic study was performed by varying a single parameter (brush thickness, while keeping all other parameters constant. AuNPs of 13 nm in diameter were attached by incubation. X-ray reflectivity, electron scanning microscopy and ellipsometry were used to study the particle loading, particle distribution and interpenetration of the particles within the brush matrix. A model for the structure of the brush/particle hybrids was derived. The particle number densities of attached AuNPs depend on the brush thickness, as do the optical properties of the hybrids. An increasing particle number density was found for increasing brush thickness, due to an increased surface roughness.

Activity of in vitro forms of dentifrices containing the hydroalcoholic extract of the ripe fruit of Eugenia uniflora L. (Surinam cherry) on cariogenic bacteria.

Science.gov (United States)

Jovito, Vanessa C; Freires, Irlan A; Almeida, Leopoldina F D; Moura, Douglas; Castro, Ricardo D; Paulo, Marçal Q; Leite-Cavalcanti, Alessandro

2011-01-01

The aim of this study was to evaluate the in vitro activity of dentifrices containing the hydroalcoholic extract of the ripe fruit of Eugenia uniflora L. (Surinam cherry) on Streptococcus oralis (ATCC 10557) and Lactobacillus casei (ATCC 7469). Five dentifrices were used: D1: containing hydroalcoholic extract of Eugenia uniflora L.; D2: containing fluoride and hydroalcoholic extract of Eugenia uniflora L.; D3: containing triclosan and hydroalcoholic extract of Eugenia uniflora L; D4: containing triclosan, fluoride and hydroalcoholic extract of Eugenia uniflora L.; D5: positive control (Colgate Total 12). To determine the antibacterial activity, the technique used was the minimum inhibitory concentration by the diffusion method in solid culture medium. At the concentration 0.05 g/mL, the best results were achieved with D1 (18 mm) and D4 (24 mm) on L.casei, and with D3 (19 mm) on S. oralis. The dentifrices D3 and D4 were found to have greater activity on the Streptococcus oralis, while D4 and D1 were found to have greater activity on Lactobaccilus casei. It is concluded that dentifrices with Eugenia uniflora L. have antimicrobial activity, suggesting that clinical trials should be conducted.

Efficacy and mechanisms of non-antibacterial, chemical plaque control by dentifrices - An in vitro study

NARCIS (Netherlands)

Busscher, Henk J.; White, Don J.; Atema-Smit, Jelly; van der Mei, Henny C.

Objectives: The provision of antiplaque benefits to dentifrices assists patients in improving hygiene and reducing susceptibility to gingivitis and caries. Chemical plaque control involves different mechanisms and is mostly associated with antibacterial effects, but also includes effects on pellicle

Clinical Effects of Stabilized Stannous Fluoride Dentifrice in Reducing Plaque Microbial Virulence I: Microbiological and Receptor Cell Findings.

Science.gov (United States)

Klukowska, Malgorzata; Haught, John Christian; Xie, Sancai; Circello, Ben; Tansky, Cheryl S; Khambe, Deepa; Huggins, Tom; White, Donald J

2017-06-01

Lipopolysaccharides (LPSs) and lipoteichoic acids (LTAs), or bacterial endotoxins, bind with Toll-like receptors (TLRs) that are expressed on host cells of the periodontium, thereby contributing to the periodontal pathogenicity of oral bacteria. Stannous fluoride (SnF2), an antibacterial fluoride that treats and controls gingivitis, has been shown to react with lipophilic domains/anionic charges in LPS and LTA. The effects of bacterial species and dental plaque on toll receptors can be studied using genetically engineered cell lines containing linked toll receptors on their surfaces. This randomized, examiner-blinded study examined the clinical effects of stabilized SnF2 dentifrice intervention on gingivitis and dental plaque virulence in populations exhibiting high and low levels of clinical gingivitis. Recruited populations were evaluated for gingival inflammation (MGI) and gingival bleeding (GBI) at baseline and assigned into two cohorts of 20 each, those with high (GBI > 20 sites) and low (GBI plaque at both healthy (no bleeding, PD = 2 mm), as well as clinically diseased sites (bleeding, PD = 3-4 mm), and then provided with an intervention hygiene product including a stabilized SnF2 dentifrice and a new soft bristle manual toothbrush. Following two and four weeks of assigned dentifrice use, participants returned for a re-evaluation of gingival inflammation and bleeding and repeat samplings of dental plaque. Plaque samples were analyzed by anaerobic culturing of gram negative anaerobes (GNA), as well as by incubation of subgingival sampled plaques with TLR4 transfected HEK293 cells, where gene expression was assessed by measurement of a SEAP alkaline phosphatase reporter as a marker of toll receptor activation. Clinical assessments showed statistically significant reductions in MGI (24-26%) and GBI (42-53%) gingivitis in both diseased and healthy cohorts following four weeks of dentifrice intervention. For all clinical examinations, MGI and bleeding sites were

Effects of two desensitizing dentifrices on dentinal tubule occlusion with citric acid challenge: Confocal laser scanning microscopy study

Directory of Open Access Journals (Sweden)

Sneha Anil Rajguru

2017-01-01

Full Text Available Background: Dentin hypersensitivity results when patent tubules are exposed to pain-inducing external stimuli. Aim: This study aims to compare the effects of two desensitizing dentifrices containing NovaMin and arginine on dentinal tubule occlusion with and without citric acid challenge in vitro using confocal laser scanning microscopy (CLSM. Materials and Methods: Forty dentin discs were randomly divided into Groups I and II containing twenty specimens each, treated with NovaMin and arginine-containing dentifrices, respectively. Groups I and II were divided into subgroups A and B where IA and IIA underwent CLSM analysis to determine the percentage of tubule occlusion while IB and IIB underwent 0.3% citric acid challenge and CLSM analysis. A novel grading system was devised to categorize tubule occlusion. Results: In Group II, the percentage of occluded tubules was highest for IIA (72.25% ± 10.57% and least for IIB (42.55% ± 8.65% having statistical significance (P < 0.0005. In Group I, the difference between IA (49.9% ± 12.96% and IB (43.15% ± 12.43% was statistically insignificant (P = 0.249. On the comparison between IB and IIB statistically indifferent result was obtained (P = 0.901, whereas the difference between IA and IIA was statistically significant (P < 0.001. The results of grading system were for IA 50% of samples belonged to Grade 2, for IIA 60% - Grade 3, and for IB 70% and for IIB 90% - Grade 2. Conclusion: Dentinal tubule occlusion with arginine-containing dentifrice was significantly higher than NovaMin. However, it could not resist citric acid challenge as effectively as NovaMin. The effects of NovaMin were more sustainable as compared to arginine-containing dentifrice, thus proving to be a better desensitizing agent.

Ultrasonic Abrasive Removal Of EDM Recast

Science.gov (United States)

Mandel, Johnny L.; Jacobson, Marlowe S.

1990-01-01

Ultrasonic abrasive process removes layer of recast material generated during electrical-discharge machining (EDM) of damper pocket on turbine blade. Form-fitted tool vibrated ultrasonically in damper pocket from which material removed. Vibrations activate abrasive in pocket. Amount of material removed controlled precisely.

Effects of different desensitizing treatments on root dentin permeability

Directory of Open Access Journals (Sweden)

Raydsa Raíssa Moura ROSA

Full Text Available Abstract The objective of this study was to evaluate the effects of diode laser and a desensitizing dentifrice on dentin permeability. Fifty-two root dentin fragments were obtained (5 × 5mm and treated with 24% EDTA gel. The samples were divided into 4 groups (n = 13: G1, control (no treatment; G2, diode laser (λ = 908 nm, 1.5 W, continuous mode, 20s; G3, application of abrasive dentifrice for 1 minute (Elmex Sensitive Professional (International Gaba; and G4, application of abrasive dentifrice for 1 minute followed by irradiation with diode laser. Ten samples per group were immersed in 2% methylene blue solution for 4h. The specimens were washed, longitudinally sectioned, observed under optical microscopy, photographed and assessed based on the degree of dye leakage. The remaining samples were observed under scanning electron microscopy (SEM. The leakage data were subjected to ANOVA test, followed by Tukey’s t-test (α = 5%. Groups 2, 3 and 4 showed less dye penetration than the control group (p < 0.05, but were similar among each other. SEM images showed that dentinal tubules were open in G1, and fused and occluded in G2. Group 3 showed dentinal tubules that were occluded by the metal ions from the toothpaste. G4 presented similar characteristics to G3, and the presence of fused dentin. The diode laser and the dentifrice were effective in reducing dentinal permeability, and the combination of the two treatments did not show better results than either one used alone.

New Rock Abrasivity Test Method for Tool Life Assessments on Hard Rock Tunnel Boring: The Rolling Indentation Abrasion Test (RIAT)

Science.gov (United States)

Macias, F. J.; Dahl, F.; Bruland, A.

2016-05-01

The tunnel boring machine (TBM) method has become widely used and is currently an important presence within the tunnelling industry. Large investments and high geological risk are involved using TBMs, and disc cutter consumption has a great influence on performance and cost, especially in hard rock conditions. Furthermore, reliable cutter life assessments facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory tests for rock abrasivity assessments are needed. A new abrasivity test method by rolling disc named Rolling Indentation Abrasion Test (RIAT) has been developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than the traditionally used methods. Wear by rolling contact on intact rock samples is introduced and several rock types, covering a wide rock abrasiveness range, have been tested by RIAT. The RIAT procedure indicates a great ability of the testing method to assess abrasive wear on rolling discs. In addition and to evaluate the newly developed RIAT test method, a comprehensive laboratory testing programme including the most commonly used abrasivity test methods and the mineral composition were carried out. Relationships between the achieved results from conventional testing and RIAT results have been analysed.

Anthrax Cases Associated with Animal-Hair Shaving Brushes.

Science.gov (United States)

Szablewski, Christine M; Hendricks, Kate; Bower, William A; Shadomy, Sean V; Hupert, Nathaniel

2017-05-01

During the First World War, anthrax cases in the United States and England increased greatly and seemed to be associated with use of new shaving brushes. Further investigation revealed that the source material and origin of shaving brushes had changed during the war. Cheap brushes of imported horsehair were being made to look like the preferred badger-hair brushes. Unfortunately, some of these brushes were not effectively disinfected and brought with them a nasty stowaway: Bacillus anthracis. A review of outbreak summaries, surveillance data, and case reports indicated that these cases originated from the use of ineffectively disinfected animal-hair shaving brushes. This historical information is relevant to current public health practice because renewed interest in vintage and animal-hair shaving brushes has been seen in popular culture. This information should help healthcare providers and public health officials answer questions on this topic.

Interaction between two polyelectrolyte brushes.

Science.gov (United States)

Kumar, N Arun; Seidel, Christian

2007-08-01

We report molecular dynamics simulations on completely charged polyelectrolyte brushes grafted to two parallel surfaces. The pressure Pi is evaluated as a function of separation D between the two grafting planes. For decreasing separation, Pi shows several regimes distinguished by their scaling with D which reflects the different physical nature of the various regimes. At weak compression the pressure obeys the 1D power law predicted by scaling theory of an ideal gas of counterions in the osmotic brush regime. In addition we find that the brushes shrink as they approach each other trying to avoid interpenetration. At higher compressions where excluded volume interactions become important, we obtain scaling exponents between -2 at small grafting density rho(a) and -3 at large rho(a). This behavior indicates a transition from a brush under good solvent condition to the melt regime with increasing grafting density.

Experimental Rock-on-Rock Abrasive Wear Under Aqueous Conditions: its Role in Subglacial Abrasion

Science.gov (United States)

Rutter, E. H.; Lee, A. G.

2003-12-01

We have determined experimentally the rate of abrasive wear of rock on rock for a range of rock types as a function of normal stress and shear displacement. Unlike abrasive wear in fault zones, where wear products accumulate as a thickening gouge zone, in our experiments wear particles were removed by flowing water. The experiments are thus directly pertinent to one of the most important processes in subglacial erosion, and to some extent in river incision. Wear was produced between rotating discs machined from rock samples and measured from the progressive approach of the disc axes towards each other under various levels of normal load. Shear displacements of several km were produced. Optical and scanning electron microscopy were used to study the worn rock surfaces, and particle size distributions in wear products were characterized using a laser particle size analyzer. Rock types studied were sandstones of various porosities and cement characteristics, schists and a granite. In all cases abrasion rate decreased logarithmically with displacement by up to 2 orders of magnitude until a steady state was approached, but only after at least 1 km displacement. The more porous, less-well cemented rocks wore fastest. Amount of abrasion could be characterized quantitatively using an exponentially decaying plus a steady-state term. Wear rate increased non-linearly with normal contact stress, apparently to an asymptote defined by the unconfined compressive strength. Microstructural study showed that the well-cemented and/or lowest porosity rocks wore by progressive abrasion of grains without plucking, whereas whole grains were plucked out of weakly-cemented and/or more porous rocks. This difference in behavior was reflected in wear-product particle size distributions. Where whole-grain plucking was possible, wear products were dominated by particles of the original grain size rather than finer rock flour. Comparison of our results to glacier basal abrasive wear estimated

Recent Developments in Abrasive Hybrid Manufacturing Processes

Directory of Open Access Journals (Sweden)

Ruszaj Adam

2017-06-01

Full Text Available Recent dynamic development of abrasive hybrid manufacturing processes results from application of a new difficult for machining materials and improvement of technological indicators of manufacturing processes already applied in practice. This tendency also occurs in abrasive machining processes which are often supported by ultrasonic vibrations, electrochemical dissolution or by electrical discharges. In the paper we present the review of new results of investigations and new practical applications of Abrasive Electrodischarge (AEDM and Electrochemical (AECM Machining.

Sandstone Turning by Abrasive Waterjet

Czech Academy of Sciences Publication Activity Database

Hlaváček, Petr; Cárach, J.; Hloch, Sergej; Vasilko, K.; Klichová, Dagmar; Klich, Jiří; Lehocká, D.

2015-01-01

Roč. 48, č. 6 (2015), s. 2489-2493 ISSN 0723-2632 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : turning away from the jet * conventional turning towards the jet * sandstone * abrasive water jet Subject RIV: JQ - Machines ; Tools Impact factor: 2.386, year: 2015 http://www.springerprofessional.de/sandstone-turning-by-abrasive-waterjet/6038028.html

Comparing the Air Abrasion Cutting Efficacy of Dentine Using a Fluoride-Containing Bioactive Glass versus an Alumina Abrasive: An In Vitro Study

Directory of Open Access Journals (Sweden)

Melissa H. X. Tan

2015-01-01

Full Text Available Air abrasion as a caries removal technique is less aggressive than conventional techniques and is compatible for use with adhesive restorative materials. Alumina, while being currently the most common abrasive used for cutting, has controversial health and safety issues and no remineralisation properties. The alternative, a bioactive glass, 45S5, has the advantage of promoting hard tissue remineralisation. However, 45S5 is slow as a cutting abrasive and lacks fluoride in its formulation. The aim of this study was to compare the cutting efficacy of dentine using a customised fluoride-containing bioactive glass Na0SR (38–80 μm versus the conventional alumina abrasive (29 μm in an air abrasion set-up. Fluoride was incorporated into Na0SR to enhance its remineralisation properties while strontium was included to increase its radiopacity. Powder outflow rate was recorded prior to the cutting tests. Principal air abrasion cutting tests were carried out on pristine ivory dentine. The abrasion depths were quantified and compared using X-ray microtomography. Na0SR was found to create deeper cavities than alumina (p<0.05 despite its lower powder outflow rate and predictably reduced hardness. The sharper edges of the Na0SR glass particles might improve the cutting efficiency. In conclusion, Na0SR was more efficacious than alumina for air abrasion cutting of dentine.

Life cycle and sustainability of abrasive tools

CERN Document Server

Linke, Barbara

2016-01-01

This monograph focuses on abrasive tools for grinding, polishing, honing, and lapping operations. The book describes the life cycle of abrasive tools from raw material processing of abrasive grits and bonding, manufacturing of monolithic or multi-layered tools, tool use to tool end-of-life. Moreover, this work highlights sustainability challenges including economic, environmental, social and technological aspects. The target audience primarily comprises research and industry experts in the field of manufacturing, but the book may also be beneficial for graduate students.

Nanopatterned polymer brushes: conformation, fabrication and applications

Science.gov (United States)

Yu, Qian; Ista, Linnea K.; Gu, Renpeng; Zauscher, Stefan; López, Gabriel P.

2015-12-01

Surfaces with end-grafted, nanopatterned polymer brushes that exhibit well-defined feature dimensions and controlled chemical and physical properties provide versatile platforms not only for investigation of nanoscale phenomena at biointerfaces, but also for the development of advanced devices relevant to biotechnology and electronics applications. In this review, we first give a brief introduction of scaling behavior of nanopatterned polymer brushes and then summarize recent progress in fabrication and application of nanopatterned polymer brushes. Specifically, we highlight applications of nanopatterned stimuli-responsive polymer brushes in the areas of biomedicine and biotechnology.

In vitro study of the effect of a dentifrice containing 8% arginine, calcium carbonate, and sodium monofluorophosphate on acid-softened enamel.

Science.gov (United States)

Rege, Aarti; Heu, Rod; Stranick, Michael; Sullivan, Richard J

2014-01-01

To investigate the possible mode of action of a dentifrice containing 8% arginine and calcium carbonate (Pro-Argin Technology), and sodium monofluorophosphate in delivering the benefits of preventing acid erosion and rehardening acid-softened enamel. The surfaces of acid-softened bovine enamel specimens were evaluated after application of a dentifrice containing 8% arginine, calcium carbonate, and sodium monofluorophosphate in vitro. Scanning Electron Microscopy (SEM), Electronic Spectrometry for Chemical Analysis (ESCA), and Secondary Ion Mass Spectrometry (SIMS) were used to characterize the enamel surfaces. Exposure of pristine enamel surfaces to citric acid resulted in clear roughening of the surface. Multiple applications of a dentifrice containing 8% arginine, calcium carbonate, and sodium monofluorophosphate to the surface of the enamel resulted in the disappearance of the microscopic voids observed by SEM as a function of treatment applications. The ESCA analysis demonstrated that both the nitrogen and carbonate levels increased as the number of treatments increased, which provides evidence that arginine and calcium carbonate were bound to the surface. Observance of arginine's signature mass fragmentation pattern by SIMS analysis confirmed the identity of arginine on the enamel surface. A series of in vitro experiments has demonstrated a possible mode of action by which a dentifrice containing 8% arginine, calcium carbonate, and sodium monofluorophosphate delivers the benefits of preventing acid erosion and rehardening acid-softened enamel. The combination of arginine and calcium carbonate adheres to the enamel surface and helps to fill the microscopic gaps created by acid, which in turn helps repair the enamel and provides a protective coating against future acid attacks.

Anti-abrasive nanocoatings current and future applications

CERN Document Server

2015-01-01

This book provides an overview of the fabrication methods for anti-abrasive nanocoatings. The connections among fabrication parameters, the characteristics of nanocoatings and the resulting properties (i.e. nanohardness, toughness, wear rate, load-bearing ability, friction coefficient, and scratch resistance) are discussed. Size-affected mechanical properties of nanocoatings are examined, including their uses. Anti-abrasive nanocoatings, including metallic-, ceramic-, and polymeric-based layers, as well as different kinds of nanostructures, such as multi-layered nanocomposites and thin films, are reviewed. * Provides a comprehensive overview of the fabrication methods for anti-abrasive nanocoatings* Discusses the connections among fabrication parameters, the characteristics of nanocoatings and the resulting properties* Reviews advantages and drawbacks of fabrication methods for anti-abrasive nanocoatings and clarifies the place of these nanocoatings in the world of nanotechnology

Abfraction, abrasion, biocorrosion, and the enigma of noncarious cervical lesions: a 20-year perspective.

Science.gov (United States)

Grippo, John O; Simring, Marvin; Coleman, Thomas A

2012-02-01

Hitherto, noncarious cervical lesions (NCCLs) of teeth have been generally ascribed to either toothbrush-dentifrice abrasion or acid "erosion." The last two decades have provided a plethora of new studies concerning such lesions. The most significant studies are reviewed and integrated into a practical approach to the understanding and designation of these lesions. A paradigm shift is suggested regarding use of the term "biocorrosion" to supplant "erosion" as it continues to be misused in the United States and many other countries of the world. Biocorrosion embraces the chemical, biochemical, and electrochemical degradation of tooth substance caused by endogenous and exogenous acids, proteolytic agents, as well as the piezoelectric effects only on dentin. Abfraction, representing the microstructural loss of tooth substance in areas of stress concentration, should not be used to designate all NCCLs because these lesions are commonly multifactorial in origin. Appropriate designation of a particular NCCL depends upon the interplay of the specific combination of three major mechanisms: stress, friction, and biocorrosion, unique to that individual case. Modifying factors, such as saliva, tongue action, and tooth form, composition, microstructure, mobility, and positional prominence are elucidated. By performing a comprehensive medical and dental history, using precise terms and concepts, and utilizing the Revised Schema of Pathodynamic Mechanisms, the dentist may successfully identify and treat the etiology of root surface lesions. Preventive measures may be instituted if the causative factors are detected and their modifying factors are considered. © 2011 Wiley Periodicals, Inc.

Abrasive wear of intermetallics

International Nuclear Information System (INIS)

Hawk, J.A.; Alman, D.E.; Wilson, R.D.

1995-01-01

The US Bureau of Mines is investigating the wear behavior of a variety of advanced materials. Among the many materials under evaluation are intermetallic alloys based on the compounds: Fe 3 Al, Ti 3 Al, TiAl, Al 3 Ti, NiAl and MoSi 2 . The high hardness, high modulus, low density, and superior environmental stability of these compounds make them attractive for wear materials. This paper reports on the abrasive wear of alloys and composites based on the above compounds. The abrasive wear behavior of these alloys and composites are compared to other engineering materials used in wear applications

Nonlinearity in the rotational dynamics of Haidinger's brushes

Science.gov (United States)

Rothmayer, Mark; Dultz, Wolfgang; Frins, Erna; Zhan, Qiwen; Tierney, Dennis; Schmitzer, Heidrun

2007-10-01

Haidinger's brushes are an entoptic effect of the human visual system that enables us to detect polarized light. However, individual perceptions of Haidinger's brushes can vary significantly. We find that the birefringence of the cornea influences the rotational motion and the contrast of Haidinger's brushes and may offer an explanation for individual differences. We have devised an experimental setup to simulate various phase shifts of the cornea and found a switching effect in the rotational dynamics of Haidinger's brushes. In addition, age related macular degeneration reduces the polarization effect of the macula and thus also leads to changes in the brush pattern.

Abrasive water jet: a complementary tool

International Nuclear Information System (INIS)

Duarte, J.P.; Pecas, P.; Nunes, E.; Gouveia, H.

1998-01-01

The abrasive water jet is a powerful cutting tool, whose main advantages lie in the absence of thermal effects and the capability of cutting highly thick materials. Compared with Laser, the abrasive water jet allows the cutting of a larger range of thicknesses and a wider variety of materials such as: ornamental stones, metals, polymers, composites, wood, glass ceramics. The application of this technology has suffered and extensive growth, with successful applications in varied industrial sectors like the automotive, aerospace, textile, metalworking, ornamental stones, etc. The present communication aims at introducing the abrasive water jet as a complementary tool to laser cutting, presenting its advantages by showing some documented examples of pieces cut for different industries. (Author) 5 refs

Assessment of mechanical and three-body abrasive wear peculiarity ...

Indian Academy of Sciences (India)

The three-body abrasive wear characteristic of fabricated composites has been assessed under different operating conditions. For this, the three-body abrasion test is done on dry abrasion test rig (TR-50)and analysed using Taguchi's experimental design scheme and analysis of variance. The results obtained from these ...

Polyelectrolyte brushes at the air/water interface

International Nuclear Information System (INIS)

Matsuoka, Hideki

2005-01-01

The nanostructure of amphiphilic diblock copolymer monolayer on water surface was investigated by in situ X-ray and neutron reflectivity. The diblock copolymers used have a long hydrophobic chain and a polyelectrolyte chain as a hydrophilic block. The monolayer was found not to have a simple double layer structure (hydrophobic layer / hydrophilic (carpet) layer) but to have a three layer structure consisting of hydrophobic layer, hydrophilic dense carpet layer, and polyelectrolyte brush layer when the polyelectrolyte block is long enough and the surface pressure (i.e. brush density) is high enough. The transition from carpet only to carpet/brush double layer structure in hydrophilic layer was observed as a function of polyelectrolyte chain length, the surface pressure. When the hydrophilic chain is a weak polyelectrolyte, the monolayer first expanded and then shrunk with increasing salt concentration in the subphase. For the strongly ionic polyelectrolyte, the monolayer structure was not affected by salt addition up to ∼0.2 M. These observations can be explained by a balance of the charged state of the brush chain, an electrostatic repulsion between brush chains and salt concentration in the brush layer

21 CFR 872.6030 - Oral cavity abrasive polishing agent.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Oral cavity abrasive polishing agent. 872.6030... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing agent. (a) Identification. An oral cavity abrasive polishing agent is a device in paste or powder form...

A randomised study to compare salivary pH, calcium, phosphate and calculus formation after using anticavity dentifrices containing Recaldent(®) and functionalized tri-calcium phosphate.

Science.gov (United States)

Sharma, Ena; Vishwanathamurthy, Ramesh Alampalli; Nadella, Manjari; Savitha, A N; Gundannavar, Gayatri; Hussain, M Ahad

2012-10-01

The aim of this study was to estimate the pH of saliva, concentration of calcium and inorganic phosphate, and calculus formation before and after usage of Recaldent(®) (GC Tooth Mousse Plus™), Functionalized Tricalcium Phosphate (3M ESPE ClinPro™ Tooth Crème) and standard dentifrice (Colgate dental cream). Randomized double-blind study. A total of 50 subjects were recruited, the subjects were assessed at their first visit, on the 21(st) day and on the 42(nd) day. At the first visit, scaling was carried out and oral hygiene instructions were given. After 21 days, the subjects were given coded dentifrices where the operator and the subjects both were unaware of the type of dentifrice. Clinical parameters assessed were Plaque index, Gingival index, and Calculus index. Salivary samples were obtained to measure calcium, phosphate levels, and pH at 21(st) day and 42(nd) day. ANOVA test, t-test, Mann-Whitney test, Kruskal-Wallis test. The mean salivary calcium level and mean salivary phosphate level were higher in Group III (functionalized tricalcium phosphate (3M ESPE ClinPro™ Tooth Creme) as compared to Group II (Recaldent(®) GC Tooth Mousse Plus™) and Group I (Colgate dental cream) on the 42(nd) day after using dentifrices, which was statistically significant. This showed that the usage of remineralizing dentifrices led to an increase in the salivary calcium, phosphate, and pH but it did not reach the level of super saturation of the ions caused by elevated pH which could lead to calculus formation. Thought here was a statistically significant increase in salivary calcium and phosphate level in all three groups from baseline to 42(nd) day, there was no calculus formation.

Interfacial Friction and Adhesion of Polymer Brushes

KAUST Repository

Landherr, Lucas J. T.

2011-08-02

A bead-probe lateral force microscopy (LFM) technique is used to characterize the interfacial friction and adhesion properties of polymer brushes. Our measurements attempt to relate the physical structure and chemical characteristics of the brush to their properties as thin-film, tethered lubricants. Brushes are synthesized at several chain lengths and surface coverages from polymer chains of polydimethylsiloxane (PDMS), polystyrene (PS), and a poly(propylene glycol)-poly(ethylene glycol) block copolymer (PPG/PEG). At high surface coverage, PDMS brushes manifest friction coefficients (COFs) that are among the lowest recorded for a dry lubricant film (μ ≈ 0.0024) and close to 1 order of magnitude lower than the COF of a bare silicon surface. Brushes synthesized from higher molar mass chains exhibit higher friction forces than those created using lower molar mass polymers. Increased grafting density of chains in the brush significantly reduces the COF by creating a uniform surface of stretched chains with a decreased surface viscosity. Brushes with lower surface tension and interfacial shear stresses manifest the lowest COF. In particular, PDMS chains exhibit COFs lower than PS by a factor of 3.7 and lower than PPG/PEG by a factor of 4.7. A scaling analysis conducted on the surface coverage (δ) in relation to the fraction (ε) of the friction force developing from adhesion predicts a universal relation ε ∼ δ4/3, which is supported by our experimental data. © 2011 American Chemical Society.

Water driven turbine/brush pipe cleaner

Science.gov (United States)

Werlink, Rudy J. (Inventor)

1995-01-01

Assemblies are disclosed for cleaning the inside walls of pipes and tubes. A first embodiment includes a small turbine with angled blades axially mounted on one end of a standoff support. An O-ring for stabilizing the assembly within the pipe is mounted in a groove within the outer ring. A replaceable circular brush is fixedly mounted on the opposite end of the standoff support and can be used for cleaning tubes and pipes of various diameters, lengths and configurations. The turbine, standoff support, and brush spin in unison relative to a hub bearing that is fixedly attached to a wire upstream of the assembly. The nonrotating wire is for retaining the assembly in tension and enabling return of the assembly to the pipe entrance. The assembly is initially placed in the pipe or tube to be cleaned. A pressurized water or solution source is provided at a required flow-rate to propel the assembly through the pipe or tube. The upstream water pressure propels and spins the turbine, standoff support and brush. The rotating brush combined with the solution cleans the inside of the pipe. The solution flows out of the other end of the pipe with the brush rotation controlled by the flow-rate. A second embodiment is similar to the first embodiment but instead includes a circular shaped brush with ring backing mounted in the groove of the exterior ring of the turbine, and also reduces the size of the standoff support or eliminates the standoff support.

Basics of cutting and abrasive processes

CERN Document Server

Toenshoff, Hans Kurt

2013-01-01

Manufacturing is the basic industrial activity generating real value. Cutting and abrasive technologies are the backbone of precision production in machine, automotive and aircraft building as well as of production of consumer goods. We present the knowledge of modern manufacturing in these technologies on the basis of scientific research. The theory of cutting and abrasive processes and the knowledge about their application in industrial practice are a prerequisite for the studies of manufacturing science and an important part of the curriculum of the master study in German mechanical engineering. The basis of this book is our lecture “Basics of cutting and abrasive processes” (4 semester hours/3 credit hours) at the Leibniz University Hannover, which we offer to the diploma and master students specializing in manufacturing science.

Dual wound dc brush motor gearhead

Science.gov (United States)

Henson, Barrie W.

1986-01-01

The design requirements, the design, development tests and problems, the qualification and life test and the findings of the strip examination of a dual wound DC brushed motor gearhead are described. It is the only space qualified dual wound dc brushed motor gearhead in Europe.

Binary Polymer Brushes of Strongly Immiscible Polymers.

Science.gov (United States)

Chu, Elza; Babar, Tashnia; Bruist, Michael F; Sidorenko, Alexander

2015-06-17

The phenomenon of microphase separation is an example of self-assembly in soft matter and has been observed in block copolymers (BCPs) and similar materials (i.e., supramolecular assemblies (SMAs) and homo/block copolymer blends (HBCs)). In this study, we use microphase separation to construct responsive polymer brushes that collapse to generate periodic surfaces. This is achieved by a chemical reaction between the minor block (10%, poly(4-vinylpyridine)) of the block copolymer and a substrate. The major block of polystyrene (PS) forms mosaic-like arrays of grafted patches that are 10-20 nm in size. Depending on the nature of the assembly (SMA, HBC, or neat BCP) and annealing method (exposure to vapors of different solvents or heating above the glass transition temperature), a range of "mosaic" brushes with different parameters can be obtained. Successive grafting of a secondary polymer (polyacrylamide, PAAm) results in the fabrication of binary polymer brushes (BPBs). Upon being exposed to specific selective solvents, BPBs may adopt different conformations. The surface tension and adhesion of the binary brush are governed by the polymer occupying the top stratum. The "mosaic" brush approach allows for a combination of strongly immiscible polymers in one brush. This facilitates substantial contrast in the surface properties upon switching, previously only possible for substrates composed of predetermined nanostructures. We also demonstrate a possible application of such PS/PAAm brushes in a tunable bioadhesion-bioadhesive (PS on top) or nonbioadhesive (PAAm on top) surface as revealed by Escherichia coli bacterial seeding.

Brush seal performance measurement system

OpenAIRE

Aksoy, Serdar; Akşit, Mahmut Faruk; Aksit, Mahmut Faruk; Duran, Ertuğrul Tolga; Duran, Ertugrul Tolga

2009-01-01

Brush seals are rapidly replacing conventional labyrinth seals in turbomachinery applications. Upon pressure application, seal stiffness increases drastically due to frictional bristle interlocking. Operating stiffness is critical to determine seal wear life. Typically, seal stiffness is measured by pressing a curved shoe to brush bore. The static-unpressurized measurement is extrapolated to pressurized and high speed operating conditions. This work presents a seal stiffness measurement syste...

Clinical and microbiologic changes associated with the combined use of a powered toothbrush and a triclosan/copolymer dentifrice: a 3-year prospective study.

Science.gov (United States)

Bogren, Anna; Teles, Ricardo P; Torresyap, Gay; Haffajee, Anne D; Socransky, Sigmund S; Wennström, Jan L

2007-09-01

Different means are available for self-performed oral hygiene. The aim of this study was to evaluate the clinical and microbiologic effects of a preventive homecare program including the combined use of a powered toothbrush and a triclosan/copolymer-containing dentifrice. A total of 160 adult subjects without signs of destructive periodontal disease were recruited for this 3-year randomized controlled trial. The subjects were assigned to a homecare program using an oscillating/rotating powered toothbrush and a triclosan/copolymer/fluoride-containing dentifrice (test) or a manual toothbrush and a standard fluoride-containing dentifrice (control). Supragingival polishing and reinforcement of homecare procedures were provided every 6 months. Plaque, bleeding on probing (BOP), and probing depth (PD) were scored at baseline and after 1, 2, and 3 years. Subgingival plaque samples were taken from the mesial aspect of each tooth at baseline and after 1, 2, and 3 years and were analyzed for their content of 40 bacterial species using checkerboard DNA-DNA hybridization. All data analyses were based on "intention-to-treat" with the subject as the statistical unit. Compared to baseline, no significant changes in clinical parameters were observed during the 3 years, except for a reduction in the mean PD at the 2- and 3-year follow-up examinations (P plaque, BOP, or PD or in the mean counts of the 40 species at any time point. The study failed to prove additional benefits of the combined use of a powered toothbrush and a triclosan/copolymer-containing dentifrice in adult subjects without signs of destructive periodontal disease.

Performance Evaluation of Abrasive Grinding Wheel Formulated ...

African Journals Online (AJOL)

This paper presents a study on the formulation and manufacture of abrasive grinding wheel using locally formulated silicon carbide abrasive grains. Six local raw material substitutes were identified through pilot study and with the initial mix of the identified materials, a systematic search for an optimal formulation of silicon ...

29 CFR 1910.215 - Abrasive wheel machinery.

Science.gov (United States)

2010-07-01

... be securely fastened to the spindle and the bearing surface shall run true. When more than one wheel... 29 Labor 5 2010-07-01 2010-07-01 false Abrasive wheel machinery. 1910.215 Section 1910.215 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.215 Abrasive wheel machinery. (a...

Anisotropy abrasive wear behavior of bagasse fiber reinforced ...

African Journals Online (AJOL)

parallel orientation (APO) and normal orientation (NO) by using a two body abrasion wear tester. Three different types of abrasives wear behaviour have been observed in the composite in three orientations and follow the following trends: WNO ...

Magnetohydrodynamic instability of a cylindrical liquid-metal brush

International Nuclear Information System (INIS)

Hong, S.H.; Wilhelm, H.E.

1976-01-01

The stability of a homopolar generator brush, consisting of a liquid-metal-filled cavity between rotating (rotor) and fixed (stator) cylinder electrodes, is analyzed in the presence of radial current transport and an axial homogeneous magnetic field. Within the frame of linear magnetohydrodynamics, it is shown that the liquid-metal flow in the brush is always unstable if the brush transports current. In the absence of current flow (infinite load) the axial magnetic field stabilizes the liquid-metal flow in the brush if the magnetic energy density is larger than a certain fraction of the energy density of the rotating fluid

Contaminated tooth brushes-potential threat to oral and general health

Directory of Open Access Journals (Sweden)

Rashmi Naik

2015-01-01

Full Text Available Background: Tooth brushing is most common method of maintaining oral hygiene. In removing plaque and other soft debris from the teeth, tooth brushes become contaminated with bacteria, blood, saliva and oral debris. These contaminated tooth brushes can be a source of infection. Aims and objectives: The aim of the present study was to evaluate the presence of microorganisms in the tooth brushes and to investigate the effect of disinfectants such as chlorhexidine gluconate, sodium hypochlorite and water to decontaminate them. Materials and Methods: Twenty-one children were asked to brush their teeth for 5 days with a tooth brush. The tooth brushes were put in Robertson′s Cooked Meat broth and were observed for growth of Streptococcal microorganisms. These tooth brushes were then placed in disinfectants such as 0.2% chlorhexidine gluconate (Group I, 1% sodium hypochlorite (Group II and water (Group III for 24 hrs and then cultured again. Reduction of growth of microorganisms was seen in Group I, Group II and remnants of growth seen in Group III. Conclusion: We conclude that the use of disinfectant for a tooth brush is a must for every individual at least at regular intervals.

Transition metal carbide and boride abrasive particles

International Nuclear Information System (INIS)

Valdsaar, H.

1978-01-01

Abrasive particles and their preparation are discussed. The particles consist essentially of a matrix of titanium carbide and zirconium carbide, at least partially in solid solution form, and grains of crystalline titanium diboride dispersed throughout the carbide matrix. These abrasive particles are particularly useful as components of grinding wheels for abrading steel. 1 figure, 6 tables

Superhydrophilic Polyelectrolyte Brush Layers with Imparted Anti-Icing Properties

DEFF Research Database (Denmark)

Chernyy, Sergey; Järn, Mikael; Shimizu, Kyoko

2014-01-01

. In general, superhydrophilic polyelectrolyte brushes exhibit better anti-icing property at -10 °C compared to partially hydrophobic brushes such as poly(methyl methacrylate) and surfactant exchanged polyelectrolyte brushes. The data are interpreted using the concept of a quasi liquid layer (QLL...

Abrasive water jet: a complementary tool

OpenAIRE

Duarte, J. P.; Peças, P.; Nunes, E.; Gouveia, H.

1998-01-01

The abrasive water jet is a powerful cutting tool, whose main advantages lie in the absence of thermal effects and the capability of cutting highly thick materials. Compared with Laser, the abrasive water jet allows the cutting of a larger range of thicknesses and a wider variety of materials such as: ornamental stones, metals, polymers, composites, wood, glass and ceramics. The application of this technology has suffered an extensive growth, with successful applications in varied industrial ...

Virtual hairy brush for digital painting and calligraphy

Institute of Scientific and Technical Information of China (English)

XU Songhua; Lau Francis C. M.; XU Congfu; PAN Yunhe

2005-01-01

The design of user friendly and expressive virtual brush systems for interactive digital painting and calligraphy has attracted a lot of attention and effort in both computer graphics and human-computer interaction circles for a long time. Providing a digital environment for paper-less artwork creation is not only challenging in terms of algorithmic design, but also promising for its potential market values. This paper proposes a novel algorithmic framework for interactive digital painting and calligraphy based a novel virtual hairy brush model. The algorithms in the kernel of our simulation framework are built upon solid modeling techniques. Implementing the algorithms, we have developed a virtual hairy brush prototype system with which end users can interactively produce high-quality digital paintings and calligraphic artwork. (The latest progress of our virtual brush project is reported at the website "http://www.cs.hku.hk/~songhua/e-brush/".)

Method for making a high current fiber brush collector

Science.gov (United States)

Scuro, S. J.

1986-05-01

An axial-type homopolar motor having high density, high current fiber brush collectors affording efficient, low contact resistance and low operating temperatures is discussed. The collectors include a ring of concentric row of brushes in equally spaced beveled holes soldered in place using a fixture for heating the ring to just below the solder melting point at a soldering iron for the local application of additional heat at each brush. Prior to soldering, an oxide film is formed on the surfaces of the brushes and ring, and the bevels are burnished to form a wetting surface. Flux applied with the solder at each bevel removes to an effective soldering depth the oxide film on the brushes and the holes.

Cold plasma brush generated at atmospheric pressure

International Nuclear Information System (INIS)

Duan Yixiang; Huang, C.; Yu, Q. S.

2007-01-01

A cold plasma brush is generated at atmospheric pressure with low power consumption in the level of several watts (as low as 4 W) up to tens of watts (up to 45 W). The plasma can be ignited and sustained in both continuous and pulsed modes with different plasma gases such as argon or helium, but argon was selected as a primary gas for use in this work. The brush-shaped plasma is formed and extended outside of the discharge chamber with typical dimension of 10-15 mm in width and less than 1.0 mm in thickness, which are adjustable by changing the discharge chamber design and operating conditions. The brush-shaped plasma provides some unique features and distinct nonequilibrium plasma characteristics. Temperature measurements using a thermocouple thermometer showed that the gas phase temperatures of the plasma brush are close to room temperature (as low as 42 deg. C) when running with a relatively high gas flow rate of about 3500 ml/min. For an argon plasma brush, the operating voltage from less than 500 V to about 2500 V was tested, with an argon gas flow rate varied from less than 1000 to 3500 ml/min. The cold plasma brush can most efficiently use the discharge power as well as the plasma gas for material and surface treatment. The very low power consumption of such an atmospheric argon plasma brush provides many unique advantages in practical applications including battery-powered operation and use in large-scale applications. Several polymer film samples were tested for surface treatment with the newly developed device, and successful changes of the wettability property from hydrophobic to hydrophilic were achieved within a few seconds

Evaluation of multi-brush anode systems in microbial fuel cells

KAUST Repository

Lanas, Vanessa

2013-11-01

The packing density of anodes in microbial fuel cells (MFCs) was examined here using four different graphite fiber brush anode configurations. The impact of anodes on performance was studied in terms of carbon fiber length (brush diameter), the number of brushes connected in parallel, and the wire current collector gage. MFCs with different numbers of brushes (one, three or six) set perpendicular to the cathode all produced similar power densities (1200±40mW/m2) and coulombic efficiencies (60%±5%). Reducing the number of brushes by either disconnecting or removing them reduced power, demonstrating the importance of anode projected area covering the cathode, and therefore the need to match electrode projected areas to maintain high performance. Multi-brush reactors had the same COD removal as single-brush systems (90%). The use of smaller Ti wire gages did not affect power generation, which will enable the use of less metal, reducing material costs. © 2013 Elsevier Ltd.

Method of forming an abrasive compact of cubic boron nitride

International Nuclear Information System (INIS)

Bell, F.R.

1976-01-01

This patent concerns an abrasive compact comprising diamond or cubic boron nitride or mixtures thereof held in a matrix of a refractory substance and a substance which dissolves the abrasive particle to at least a limited extent. The compact may be made by subjecting a powdered mixture of the ingredients to conditions of temperature and pressure at which the abrasive particle is crystallographically stable and the solvent substance acts to dissolve the abrasive particle. The refractory substance and solvent substance are preferably so chosen that during compact manufacture there is interaction resulting in the formation of a hard material

LITERATURE SURVEY ON ABRASION PROBLEM IN CHENILLE YARNS

Directory of Open Access Journals (Sweden)

Erhan Kenan ÇEVEN

2006-01-01

Full Text Available Chenille yarns are traditionally used in the manufacture of furnishing fabrics, fashion knitwear, and as decorative threads in many types of broad and narrow fabrics. Chenille yarn has a very distinct weakness-it does not have very good inherent abrasion resistance. When the yarns are in use, clearly the abrasion resistance of the chenille yarn is crucially important. Either during further processing or during the eventual end-use, any removal of the effect yarn forming the beard will expose the ground yarns, which in turn will result in a bare appearance. To avoid this undesirable result, several options are available. Therefore, the studies on this area are about the investigation of the influences of some material types and machine parameters on the abrasion resistance of chenille yarns and fabrics produced with these yarns. In this paper, the experimental studies about the abrasion properties of chenille yarns in yarn, knitted and woven fabric forms are summarized.

Control technology for crystalline silica exposures in construction: wet abrasive blasting.

Science.gov (United States)

Golla, Vijay; Heitbrink, William

2004-03-01

This study was designed to document the effect that wet abrasive blasting has on reducing worker exposure to crystalline silica, which has been associated with silicosis and premature death. In this study, worker exposure to respirable crystalline silica was monitored during wet abrasive blasting on the exterior walls of a parking garage to remove surface concrete and expose the underlying aggregate. In this process a wet sand mix comprised of 80% dry sand and 20% water was used. Sampling and analysis revealed that the geometric mean respirable quartz concentration was 0.2 mg/m(3) for workers conducting abrasive blasting and 0.06 mg/m(3) for helpers. When abrasive blasting was conducted in areas that apparently had reduced natural ventilation, dust exposures appeared to increase. When compared with other published data, this case study suggests that wet abrasive blasting causes less exposure to crystalline silica than dry abrasive blasting.

Electrical resistivity measurements to predict abrasion resistance of ...

Indian Academy of Sciences (India)

WINTEC

increasing expansion of highway and other construction works and decreasing natural aggregate resources in the world, the demand for crushed stone aggregates has in- creased from day-to-day. One of the important properties of rock aggregates is abrasion resistance. The abrasion resistance of aggregates is generally ...

Submerged cutting characteristics of abrasive suspension jet

International Nuclear Information System (INIS)

Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroki

2015-01-01

An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

Abrasive wear of ceramic wear protection at ambient and high temperatures

Science.gov (United States)

Varga, M.; Adam, K.; Tumma, M.; Alessio, K. O.

2017-05-01

Ceramic wear protection is often applied in abrasive conditions due to their excellent wear resistance. This is especially necessary in heavy industries conveying large amounts of raw materials, e.g. in steel industry. Some plants also require material transport at high temperatures and velocities, making the need of temperature stable and abrasion resistant wear protection necessary. Various types and wear behaviour of ceramic protection are known. Hence, the goal of this study is to identify the best suitable ceramic materials for abrasive conditions in harsh environments at temperatures up to 950°C and severe thermal gradients. Chamottes, known for their excellent thermal shock resistance are compared to high abrasion resistant ceramic wear tiles and a cost efficient cement-bounded hard compound. Testing was done under high-stress three-body abrasion regime with a modified ASTM G65 apparatus enabling for investigations up to ~950°C. Thereto heated abrasive is introduced into the wear track and also preheated ceramic samples were used and compared to ambient temperature experiments. Results indicate a significant temperature influence on chamottes and the hard compound. While the chamottes benefit from temperature increase, the cement-bounded hard compound showed its limitation at abrasive temperatures of 950°C. The high abrasion resistant wear tiles represented the materials with the best wear resistance and less temperature influence in the investigated range.

Influence of martensitic phase in abrasion behaviour of stainless steel 304 L

International Nuclear Information System (INIS)

Ruzzante, J.; Alvarez, P.; Hey, A.; Gestido, G.D.; Vosen, J.H.; Fernandez, H.A.

1986-01-01

Abrasion behaviour is studied in commercial stainless steels of different class compositions by standard. The work achieved guieds in structural analysis of superficial coat formed and its relation with abrasion variables, load and velocity. The abrasion is made in an equipment LF WK of high velocity with friction powers, abrasion velocity and temperature variation registered on the tested piece. The abrasion zone is studied with scanning electron microscope (SEM). The deformed superficial zone nature is studied relationing its microstructure with profile corresponding of microhardness. (C.M.C.T.R.) [pt

75 FR 13489 - Natural Bristle Paint Brushes and Brush Heads from the People's Republic of China: Final Results...

Science.gov (United States)

2010-03-22

... Brushes and Brush Heads from the People's Republic of China: Final Results of the Expedited Sunset Review... from the People's Republic of China (``PRC'') pursuant to section 751(c) of the Tariff Act of 1930, as amended (``the Act''). See Initiation of Five-year (``Sunset'') Review, 74 FR 56593 (November 2, 2009...

Tooth brushing among 11- to 15-year-olds in Denmark

DEFF Research Database (Denmark)

Bast, L. S.; Holstein, B. E.; Nordahl, Helene

2015-01-01

brushing. Results: 10,607 respondents: a response rate of 88.3%. Boys of lower social class had higher odds ratio (OR) of infrequent tooth brushing than girls: 1.98 (95% confidence interval 1.62-2.41) vs 1.80 (1.53-2.24). Immigrants and descendants had higher odds compared to adolescents of Danish origin......Objective: Regular tooth brushing in adolescence predicts stable tooth brushing habits later in life. Differences in tooth brushing habits by ethnic background and socioeconomic position have been suggested. We investigated migration status and social class in relation to infrequent tooth brushing...... both separately and combined. Methods: The study population was 11-15 year-olds chosen from a clustered random sample of schools. Univariate and multivariate logistic regression analyses estimated the separate and combined effects of migration status and social class on less than twice daily tooth...

Clinical evaluation of a newly designed orthodontic tooth brush - A clinical study

Directory of Open Access Journals (Sweden)

C S Saimbi

2009-01-01

In this study, the newly designed orthodontic tooth brush is compared with an ordinary tooth brush. Results of this study show that the newly designed orthodontic tooth brush is superior in its cleaning efficiency as compared to the ordinary tooth brush. The results show that plaque removing capacity of orthodontic tooth brush is nearly 95-99%.

Polyacrylic acid polymer brushes as substrates for the incorporation of anthraquinone derivatives. Unprecedented application of decorated polymer brushes on organocatalysis

Science.gov (United States)

Ruiz-Muelle, Ana Belén; Contreras-Cáceres, Rafael; Oña-Burgos, Pascual; Rodríguez-Dieguez, Antonio; López-Romero, Juan Manuel; Fernández, Ignacio

2018-01-01

The synthesis of amino-terminated anthraquinone derivatives and their incorporation onto polymer brushes for the fabrication of silicon-based nanometric functional coatings are described for the first time. The general process involves the covalent grafting of anthraquinone 1 onto two different polymer-brushes by amidation reactions. They are composed by amino- and carboxy-terminated poly(acrylic acid) chains (PAA-NH2- and PAA-COOH, respectively) tethered by one end to an underlying silicon oxide (SiO2) substrate in a polymer brush configuration. A third substrate is fabricated by UV induced hydrosilylation reaction using undecenoic acid as adsorbate on hydrogen-terminated Si(111) surfaces. One- and two-dimensional nuclear magnetic resonance (NMR), FT-IR, MS and X-ray diffraction (XRD) were used to characterize anthraquinone 1. Ellipsometric and X-ray photoelectron spectroscopy (XPS) measurements demonstrated the presence of the polymer brushes on the silicon wafers, and atomic force microscopy (AFM) was used to study its surface morphology. The covalent linkage between anthraquinone and polymer brushes was proven by XPS and confocal fluorescence microscopy. The resulting surfaces were assayed in the heterogenous organocatalytic transformation of (1H)-indole into 3-benzyl indole with moderate yields but with high recyclability.

Solidification structure and abrasion resistance of high chromium white irons

Science.gov (United States)

Doğan, Ö. N.; Hawk, J. A.; Laird, G.

1997-06-01

Superior abrasive wear resistance, combined with relatively low production costs, makes high Cr white cast irons (WCIs) particularly attractive for applications in the grinding, milling, and pumping apparatus used to process hard materials. Hypoeutectic, eutectic, and hypereutectic cast iron compositions, containing either 15 or 26 wt pct chromium, were studied with respect to the macrostructural transitions of the castings, solidification paths, and resulting microstructures when poured with varying superheats. Completely equiaxed macrostructures were produced in thick section castings with slightly hypereutectic compositions. High-stress abrasive wear tests were then performed on the various alloys to examine the influence of both macrostructure and microstructure on wear resistance. Results indicated that the alloys with a primarily austenitic matrix had a higher abrasion resistance than similar alloys with a pearlitic/bainitic matrix. Improvement in abrasion resistance was partially attributed to the ability of the austenite to transform to martensite at the wear surface during the abrasion process.

Endobiliary brush biopsy

DEFF Research Database (Denmark)

Adamsen, Sven; Olsen, Marianne; Jendresen, Marianne Bille

2006-01-01

OBJECTIVE: Obtaining cytological specimens by wire-guided endobiliary brushing at the time of endoscopic retrograde cholangiopancreatography (ERCP) is a convenient way to reach a diagnosis. Sensitivity for malignant disease is generally around 50% and specificity around 100%. The present study wa...

Modeling of Micro Deval abrasion loss based on some rock properties

Science.gov (United States)

Capik, Mehmet; Yilmaz, Ali Osman

2017-10-01

Aggregate is one of the most widely used construction material. The quality of the aggregate is determined using some testing methods. Among these methods, the Micro Deval Abrasion Loss (MDAL) test is commonly used for the determination of the quality and the abrasion resistance of aggregate. The main objective of this study is to develop models for the prediction of MDAL from rock properties, including uniaxial compressive strength, Brazilian tensile strength, point load index, Schmidt rebound hardness, apparent porosity, void ratio Cerchar abrasivity index and Bohme abrasion test are examined. Additionally, the MDAL is modeled using simple regression analysis and multiple linear regression analysis based on the rock properties. The study shows that the MDAL decreases with the increase of uniaxial compressive strength, Brazilian tensile strength, point load index, Schmidt rebound hardness and Cerchar abrasivity index. It is also concluded that the MDAL increases with the increase of apparent porosity, void ratio and Bohme abrasion test. The modeling results show that the models based on Bohme abrasion test and L type Schmidt rebound hardness give the better forecasting performances for the MDAL. More models, including the uniaxial compressive strength, the apparent porosity and Cerchar abrasivity index, are developed for the rapid estimation of the MDAL of the rocks. The developed models were verified by statistical tests. Additionally, it can be stated that the proposed models can be used as a forecasting for aggregate quality.

Neuro - Fuzzy Analysis for Silicon Carbide Abrasive Grains ...

African Journals Online (AJOL)

Grinding wheels are made of very small, sharp and hard abrasive materials or grits held together by strong porous bond. Abrasive materials are materials of extreme hardness that are used to shape other materials by a grinding or abrading action and they are used either as loose grains, as grinding wheels, or as coatings ...

Third abrasive wear mode: is it possible?

Directory of Open Access Journals (Sweden)

Ronaldo Câmara Cozza

2014-04-01

Full Text Available The objective of this paper is to propose an initial discussion on the characterization of a third abrasive wear mode. The results obtained in a previous work [1] under different test conditions revealed the occurrence of the superposition of the “rolling” and “grooving” abrasive wear modes. This phenomenon was denoted “micro-rolling abrasion” due to the observation that “rolling abrasion” was found to act on “grooving abrasion”.

Electroosmotic Flow in Mixed Polymer Brush-Grafted Nanochannels

Directory of Open Access Journals (Sweden)

Qianqian Cao

2016-12-01

Full Text Available Mixed polymer brush-grafted nanochannels—where two distinct species of polymers are alternately grafted on the inner surface of nanochannels—are an interesting class of nanostructured hybrid materials. By using a coarse-grained molecular dynamics simulation method, we are able to simulate the electrokinetic transport dynamics of the fluid in such nanochannels as well as the conformational behaviors of the mixed polymer brush. We find that (1 the brush adopts vertically-layered and longitudinally-separated structures due to the coupling of electroosmotic flow (EOF and applied electric field; (2 the solvent quality affects the brush conformations and the transport properties of the EOF; (3 the EOF flux non-monotonically depends on the grafting density, although the EOF velocity in the central region of the channel monotonically depends on the grafting density.

Behavioral Determinants of Brushing Young Children's Teeth: Implications for Anticipatory Guidance

Science.gov (United States)

Huebner, Colleen E.; Riedy, Christine A.

2010-01-01

Purpose The purposes of this study were to identify parents' motivation, support, and barriers to twice daily tooth-brushing of infants and preschool-age children and to discover new approaches to encourage this important health behavior. Methods Qualitative interviews were conducted with 44 rural parents about tooth-brushing habits and experiences. Results Forty of 44 parents reported that they had begun to brush their child's teeth; 24 (55%) reported brushing twice a day or more. Parents who brushed twice a day, vs less often, were more likely to describe specific skills to overcome barriers; they expressed high self-efficacy and held high self-standards for brushing. Parents who brushed their children's teeth less than twice daily were more likely to: hold false beliefs about the benefits of twice daily tooth-brushing; report little normative pressure or social support for the behavior; have lower self-standards; describe more external constraints; and offer fewer ideas to overcome barriers. Conclusions The findings support an integrative framework in which barriers and support for parents' twice daily brushing of their young children's teeth are multiple and vary among individuals. Knowledge of behavioral determinants specific to individual parents could strengthen anticipatory guidance and recommendations about at-home oral hygiene of young children. PMID:20298653

Abrasive water jet cutting

International Nuclear Information System (INIS)

Leist, K.J.; Funnell, G.J.

1988-01-01

In the process of selecting a failed equipment cut-up tool for the process facility modifications (PFM) project, a system using an abrasive water jet (AWJ) was developed and tested for remote disassembly of failed equipment. It is presented in this paper

Atmospheric particulate emissions from dry abrasive blasting using coal slag

Energy Technology Data Exchange (ETDEWEB)

Bhaskar Kura; Kalpalatha Kambham; Sivaramakrishnan Sangameswaran; Sandhya Potana [University of New Orleans, New Orleans, LA (United States). Department of Civil and Environmental Engineering

2006-08-15

Coal slag is one of the widely used abrasives in dry abrasive blasting. Atmospheric emissions from this process include particulate matter (PM) and heavy metals, such as chromium, lead, manganese, nickel. Quantities and characteristics of PM emissions depend on abrasive characteristics and process parameters. Emission factors are key inputs to estimate emissions. Experiments were conducted to study the effect of blast pressure, abrasive feed rate, and initial surface contamination on total PM (TPM) emission factors for coal slag. Rusted and painted mild steel surfaces were used as base plates. Blasting was carried out in an enclosed chamber, and PM was collected from an exhaust duct using U.S. Environment Protection Agency source sampling methods for stationary sources. Results showed that there is significant effect of blast pressure, feed rate, and surface contamination on TPM emissions. Mathematical equations were developed to estimate emission factors in terms of mass of emissions per unit mass of abrasive used, as well as mass of emissions per unit of surface area cleaned. These equations will help industries in estimating PM emissions based on blast pressure and abrasive feed rate. In addition, emissions can be reduced by choosing optimum operating conditions. 40 refs., 5 figs., 2 tabs.

Surface grafted polymer brushes: potential applications in dengue biosensors

Energy Technology Data Exchange (ETDEWEB)

Baratela, Fernando Jose Costa; Higa, Olga Zazuco, E-mail: ozahiga@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Faria, Henrique Antonio Mendonca de; Queiroz, Alvaro Antonio Alencar de, E-mail: alencar@unifei.edu.br [Universidade Federal de Itajuba (UNIFEI), Itajuba, MG (Brazil). Instituto de Fisica e Quimica

2013-07-01

A polymer brush membrane-based ultrasensitive biosensor for dengue diagnosis was constructed using poly(hydroxyethyl methacrylate) (PHEMA) brushes immobilized onto low density polyethylene (LDPE) films. LDPE surface films were initially modified by Ar{sup +} ion irradiation to activate the polymer surface. Subsequently, graft polymerization of 2-hydroxyethyl methacrylate onto the activated LDPE surface was carried out under aqueous conditions to create patterned polymer brushes of PHEMA. The grafted PHEMA brushes were characterized by Fourier transform-infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and contact angle analysis. The SEM observations showed that selective surface activation with Ar+ implantation and graft polymerization on the selectively activated surface had occurred. The PHEMA brushes were electrically characterized in the presence of concentrations of human immunoglobulin (IgG). The proposed amperometric biosensor was successfully used for determination of IgG in physiologic samples with excellent responses. (author)

Surface grafted polymer brushes: potential applications in dengue biosensors

International Nuclear Information System (INIS)

Baratela, Fernando Jose Costa; Higa, Olga Zazuco; Faria, Henrique Antonio Mendonca de; Queiroz, Alvaro Antonio Alencar de

2013-01-01

A polymer brush membrane-based ultrasensitive biosensor for dengue diagnosis was constructed using poly(hydroxyethyl methacrylate) (PHEMA) brushes immobilized onto low density polyethylene (LDPE) films. LDPE surface films were initially modified by Ar + ion irradiation to activate the polymer surface. Subsequently, graft polymerization of 2-hydroxyethyl methacrylate onto the activated LDPE surface was carried out under aqueous conditions to create patterned polymer brushes of PHEMA. The grafted PHEMA brushes were characterized by Fourier transform-infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and contact angle analysis. The SEM observations showed that selective surface activation with Ar+ implantation and graft polymerization on the selectively activated surface had occurred. The PHEMA brushes were electrically characterized in the presence of concentrations of human immunoglobulin (IgG). The proposed amperometric biosensor was successfully used for determination of IgG in physiologic samples with excellent responses. (author)

Efficiency of the surgical washing of hands with brush and without brush

Directory of Open Access Journals (Sweden)

Fresia Canales Carmona

2013-10-01

Full Text Available The purpose of this article is to establish the answer to a clinical question regarding the effectiveness ofpreoperative hygiene with hand washing brush or without it. This first technique has been performed on the skinto reduce transient bacteria and to inhibit the growth of resident microorganisms as a common and required actbefore any surgical procedure. Despite this measure and others such as prophylactic antibiotics, the mainoperative complication continues to be the surgical wound infection. Today, it is as prevalent as in the past withthe consequent negative effects derived from it, both for the institutions and for patients. Being controversialtoday which one is the most effective and safe surgical hand washing method for the binomial: professionalsurgical team/ patient, this study is done under the criteria of the Evidence-Based Nursing.A question was builtin PICO format (Personal, Intervention, Comparison and Outcome. After this is done, continues informationsearch in the databases GOOGLE ACADÉMICO, Pub Med, Cochrane y Base de Datos para la Investigación enEnfermería (BDIE We obtained 20 articles related to the topic of them 8, which fulfilled the set CASPe criteriato answer the clinical question, were analyzed. We conclude that washing hands with a brush is equally effectiveas without brush technique in terms of decreased of the superficial skin bacterial flora, although this technique hasadvantages over the traditional practice.

Polymer Brushes: Synthesis, Characterization, Applications

Science.gov (United States)

Advincula, Rigoberto C.; Brittain, William J.; Caster, Kenneth C.; Rühe, Jürgen

2004-09-01

Materials scientists, polymer chemists, surface physicists and materials engineers will find this book a complete and detailed treatise on the field of polymer brushes, their synthesis, characterization and manifold applications. In a first section, the various synthetic pathways and different surface materials are introduced and explained, followed by a second section covering important aspects of characterization and analysis in both flat surfaces and particles. These specific surface initiated polymerization (SIP) systems such as linear polymers, homopolymers, block copolymers, and hyperbranched polymers are unique compared to previously reported systems by chemisorption or physisorption. They have found their way in both large-scale and miniature applications of polymer brushes, which is covered in the last section. Such 'hairy' surfaces offer fascinating opportunities for addressing numerous problems of both academic and, in particular, industrial interest: high-quality, functional or protective coatings, composite materials, surface engineered particles, metal-organic interfaces, biological applications, micro-patterning, colloids, nanoparticles, functional devices, and many more. It is the desire of the authors that this book will be of benefit to readers who want to "brush-up on polymers".

Antifouling Properties of Fluoropolymer Brushes toward Organic Polymers

NARCIS (Netherlands)

Wang, Zhanhua; Zuilhof, Han

2016-01-01

Fluoropolymer brushes are widely used to prevent nonspecific adsorption of commercial polymeric or biological materials due to their strongly hydrophobic character. Herein, a series of fluoropolymer brushes with different compositions, thicknesses and molecular architectures was prepared via

Submerged cutting characteristics of abrasive suspension jet

International Nuclear Information System (INIS)

Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroyuki

2015-01-01

An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth under submerged condition divided by the cutting depth in air at the same standoff distance. The relative cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

Evaluation of the fluoride stability of dentifrices sold in Manaus, AM, Brazil Estabilidade do fluoreto de dentifrícios comercializados em Manaus, AM, Brasil

Directory of Open Access Journals (Sweden)

Nikeila Chacon de Oliveira Conde

2003-09-01

Full Text Available The minimum requirement for the anti-caries effect of a dentifrice is the presence of available and stable fluoride in the formulation. The concentration of available fluoride in the major dentifrices sold in Brazil has been reported, but few data have been published about its stability, which is temperature-dependent. Thus, the aim of this study was to evaluate the concentration and stability of fluoride in dentifrices sold in Manaus, AM, Brazil, which is a typical tropical city. The concentrations of total fluoride, total soluble fluoride, MFP, and of insoluble fluoride of six Brazilian dentifrices and an imported one were analyzed. The analyses were made when the dentifrices were purchased and during a year of storage at room temperature (28.9 ± 1.16°C and under refrigeration (26.3 ± 0.88°C. The analyses were performed using an ion specific electrode Orion 96-09. At the time of purchase, all the dentifrices analyzed showed more than 1,000 ppm (mug F-/g; w/w of soluble fluoride. However, in most of them, this form of fluoride was not shown to be stable. The highest loss of soluble fluoride was found for storage at room temperature, reaching up to 40%. Although all dentifrices comply with the Brazilian guidelines with regard to the concentration of total fluoride (maximum of 0.15%, the instability of soluble fluoride observed in some of them can impair their anti-caries effect and this condition is not contemplated in the Governmental rules.O requisito mínimo para que um dentifrício tenha potencial anticárie é ele ter uma formulação com fluoreto na forma solúvel e estável. A concentração de fluoreto solúvel nos dentifrícios vendidos no Brasil tem sido descrita, mas pouco é conhecido sobre sua estabilidade, a qual é função da temperatura. Assim, o objetivo deste estudo foi avaliar a concentração e estabilidade do fluoreto em dentifrícios vendidos em Manaus, AM, Brasil. As concentrações de fluoreto total, fluoreto sol

Analysis of coarse aggregate performance based on the modified Micro Deval abrasion test

Directory of Open Access Journals (Sweden)

Jiangfeng Wu

2018-03-01

Full Text Available The anti-abrasion property of aggregate significantly affects the performance of the pavement. In this research, the quartzite and gneiss which were produced in Lincheng County, Xingtai City, Hebei Province were selected as test samples. According to the American Society for Testing and Materials standard, the Micro-Deval abrasion test was taken every 1000 rotation times until 20,000 times, and the change trend of the Micro-Deval abrasion value was obtained. Results showed that the abrasion values were in the exponential growth rate rather than linear rate. Their R-Square coefficient was 0.99142 and 0.99916 respectively. The gravel information such as area, roundness, diameter, perimeter and so on were calculated and analyzed by Image-Pro Plus software, which provided a rapid way for the 2D morphology characteristics analysis of the coarse aggregate. Keywords: Micro-Deval abrasion test, Coarse aggregate, Anti-abrasion property, Abrasion values

Abrasive wear of WC-NiMoCrFeCo thermally sprayed coatings in dependence on different types of abrasive sands

Czech Academy of Sciences Publication Activity Database

Kašparová, M.; Zahálka, F.; Houdková, Š.; Ctibor, Pavel

2010-01-01

Roč. 48, č. 1 (2010), s. 75-85 ISSN 0023-432X R&D Projects: GA AV ČR 1QS200430560 Institutional research plan: CEZ:AV0Z20430508 Keywords : WC-Hastelloy * abrasive wear * Al2O3 sand * SiO2 sand * braun size * abrasive efficiency Subject RIV: JG - Metallurgy Impact factor: 0.471, year: 2010 http://kovmat.sav.sk/abstract.php?rr=48&cc=1&ss=73

Brushes and soap : grafted polymers and their interactions with nanocolloids

NARCIS (Netherlands)

Currie, E.P.K.

2000-01-01

Layers of polymer chains end-attached to a grafting plane at high densities, so-called brushes, are a curious state of matter. The (average) monomer density within the brush is as high as in a semi-dilute polymer solution, resulting in a high osmotic pressure in the brush. Due to the

LM2500+ Brush Seal Case Study

Science.gov (United States)

Haaser, Fred G.

2006-01-01

The LM2500+ industrial aeroderivative gas turbine, a 25% enhanced power derivative of the LM2500 gas turbine, recently completed its development test program during the period 5/96 - 10/96. Early in the engine program a Quality Function Deployment (QFD) process was used to determine customer needs for this project.The feedback obtained from the QFD process showed without doubt that gas turbine customers now emphasize product reliability and availability at the top of their needs. One area of development on the LM2500+ was to investigate the use of a brush seal as a means to reduce undesirable turbine cooling leakages within the turbine mid frame in order to enhance part life. This presentation presents a case study on the factors that went into evaluating a brush seal during engine test, test results, and the ultimate decision not to implement the brush seal for cost and other reasons.

Mangrove Cultivation For Dealing With Coastal Abrasion Case Study Of Karangsong

Science.gov (United States)

Fatimatuzzahroh, Feti; Hadi, Sudharto P.; Purnaweni, Hartuti

2018-02-01

Coastal abrasion is consequence from destructive waves and sea current. One of cause is human intervention. The effort to solve of abrasion is by mangrove cultivation. Mangroves are halophyte plant that can restrain the sea wave. Mangrove cultivation required participation community that give awareness the importance of mangrove in coastal sustainability. Mangroves in coastal Karangsong, Indramayu west java, in 2007 was through abrasion approximately 127.30 ha. Mangrove cultivation in Karangsong has been replanting since 1998 to 2003, but there was no maintenance and management. In 2007 until 2015 Karangsong replanting mangroves and has been succeed. Karangsong became the center of mangrove study for west java area in 2015. This achievement is result of cooperation between community, NGO, and local government. In addition, this effort made not only overcome the abrasion problem but also give community awareness about the importance of mangrove cultivation in preventing coastal abrasion throughout community development. This paper reviews abrasion in Karangsong and the impact for local community and empowerment in mangrove cultivation. To achieve the success mangrove cultivation required community development approach from planning process, planting, maintenance and management.

Experimental Research into Technology of Abrasive Flow Machining Nonlinear Tube Runner

Directory of Open Access Journals (Sweden)

Junye Li

2014-06-01

Full Text Available In the fields of military and civil uses, some special passages exist in many major parts, such as non-linear tubes. The overall performance is usually decided by the surface quality. Abrasive flow machining (AFM technology can effectively improve the surface quality of the parts. In order to discuss the mechanism and technology of abrasive flow machining nonlinear tube, the nozzle is picked up as the researching object, and the self-designed polishing liquid is employed to make research on the key technological parameters of abrasive flow machining linear tube. Technological parameters’ impact on surface quality of the parts through the nozzle surface topography and scanning electron microscopy (SEM map is explored. It is experimentally confirmed that abrasive flow machining can significantly improve surface quality of nonlinear runner, and experimental results can provide technical reference to optimizing study of abrasive flow machining theory.

Polyelectrolyte brushes in mixed ionic medium studied via intermolecular forces

Science.gov (United States)

Farina, Robert; Laugel, Nicolas; Pincus, Philip; Tirrell, Matthew

2011-03-01

The vast uses and applications of polyelectrolyte brushes make them an attractive field of research especially with the growing interest in responsive materials. Polymers which respond via changes in temperature, pH, and ionic strength are increasingly being used for applications in drug delivery, chemical gating, etc. When polyelectrolyte brushes are found in either nature (e.g., surfaces of cartilage and mammalian lung interiors) or commercially (e.g., skin care products, shampoo, and surfaces of medical devices) they are always surrounded by mixed ionic medium. This makes the study of these brushes in varying ionic environments extremely relevant for both current and future potential applications. The polyelectrolyte brushes in this work are diblock co-polymers of poly-styrene sulfonate (N=420) and poly-t-butyl styrene (N=20) which tethers to a hydrophobic surface allowing for a purely thermodynamic study of the polyelectrolyte chains. Intermolecular forces between two brushes are measured using the SFA. As multi-valent concentrations are increased, the brushes collapse internally and form strong adhesion between one another after contact (properties not seen in a purely mono-valent environment).

Carbazole functionalized isocyanide brushes in heterojunction photovoltaic devices

NARCIS (Netherlands)

Lim, E.; Gao, F.; Schwartz, E.; Schwartz, E.; Cornelissen, Jeroen Johannes Lambertus Maria; Nolte, R.J.M.; Rowan, A.E.; Greenham, N.C.; Do, L.M.

2012-01-01

In this work, carbazole-containing polyisocyanide (PIACz) brushes were used for photovoltaic devices. A photovoltaic device was fabricated on top of the brushes by spin-coating a suitable acceptor and evaporating an Al cathode. Devices with a poly(N-vinylcarbazole) (PVK) bulk polymer were also

Wildlife responses to brush management: a contemporary evaluation

Science.gov (United States)

Brush management has been widely practiced with the general intent of curtailing or reversing the proliferation of shrubs and trees in grasslands and savannas. The traditional aim of brush management has been to increase livestock forage or to improve water yield. Its potential role for restoring h...

A Review on Parametric Analysis of Magnetic Abrasive Machining Process

Science.gov (United States)

Khattri, Krishna; Choudhary, Gulshan; Bhuyan, B. K.; Selokar, Ashish

2018-03-01

The magnetic abrasive machining (MAM) process is a highly developed unconventional machining process. It is frequently used in manufacturing industries for nanometer range surface finishing of workpiece with the help of Magnetic abrasive particles (MAPs) and magnetic force applied in the machining zone. It is precise and faster than conventional methods and able to produce defect free finished components. This paper provides a comprehensive review on the recent advancement of MAM process carried out by different researcher till date. The effect of different input parameters such as rotational speed of electromagnet, voltage, magnetic flux density, abrasive particles size and working gap on the performances of Material Removal Rate (MRR) and surface roughness (Ra) have been discussed. On the basis of review, it is observed that the rotational speed of electromagnet, voltage and mesh size of abrasive particles have significant impact on MAM process.

Design and Testing of High Performance Brushes.

Science.gov (United States)

1983-05-01

shows an example. What ordinarily serves as a ’brush’. applitations such as homopolar motors / generators and in transmitting current across an interface...speed current collection bricating layer of silver and graphite debris. systems for homopolar electrical machines. Use The other, associated with the...performantc hornopolar by examining the origin of the power losses when electrical motors and generators, based either on superconducting or brushes

21 CFR 868.5795 - Tracheal tube cleaning brush.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Tracheal tube cleaning brush. 868.5795 Section 868.5795 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5795 Tracheal tube cleaning brush. (a...

Decontamination of Steam Generator tube using Abrasive Blasting Technology

International Nuclear Information System (INIS)

Min, B. Y.; Kim, G. N.; Choi, W. K.; Lee, K. W.; Kim, D. H.; Kim, K. H.; Kim, B. T.

2010-01-01

As a part of a technology development of volume reduction and self disposal for large metal waste project, We at KAERI and our Sunkwang Atomic Energy Safety (KAES) subcontractor colleagues are demonstrating radioactively contaminated steam generator tube by abrasive blasting technology at Kori-1 NPP. A steam generator is a crucial component in a PWR (pressurized Water Reactor). It is the crossing between the primary, contaminated, circuit and the secondary waste-steam circuit. The heat from the primary reactor coolant loop is transferred to the secondary side in thousands of small tubes. Due to several problems in the material of those tube, like SCC (Stress Corrosion Cracking), insufficient control in water chemistry, which can be cause of tube leakage, more and more steam generators are replaced today. Only in Korea, already 2 of them are replaced and will be replaced in the near future. The retired 300 ton heavy Steam generator was stored at the storage waste building of Kori NPP site. The steam generator waste has a large volume, so that it is necessary to reduce its volume by decontamination. A waste reduction effect can be obtained through decontamination of the inner surface of a steam generator. Therefore, it is necessary to develop an optimum method for decontamination of the inner surface of bundle tubes. The dry abrasive blasting is a very interesting technology for the realization of three-dimensional microstructures in brittle materials like glass or silicon. Dry abrasive blasting is applicable to most surface materials except those that might be shattered by the abrasive. It is most effective on flat surface and because the abrasive is sprayed and can also applicable on 'hard to reach' areas such as inner tube ceilings or behind equipment. Abrasive decontamination techniques have been applied in several countries, including Belgium, the CIS, France, Germany, Japan, the UK and the USA

Innovative decontamination technology by abrasion in vibratory vessels

International Nuclear Information System (INIS)

Fabbri, Silvio; Ilarri, Sergio

2007-01-01

Available in abstract form only. Full text of publication follows: The possibility of using conventional vibratory vessel technology as a decontamination technique is the motivation for the development of this project. The objective is to explore the feasibility of applying the vibratory vessel technology for decontamination of radioactively-contaminated materials such as pipes and metal structures. The research and development of this technology was granted by the U.S. Department of Energy (DOE). Abrasion processes in vibratory vessels are widely used in the manufacture of metals, ceramics, and plastics. Samples to be treated, solid abrasive media and liquid media are set up into a vessel. Erosion results from the repeated impact of the abrasive particles on the surface of the body being treated. A liquid media, generally detergents or surfactants aid the abrasive action. The amount of material removed increases with the time of treatment. The design and construction of the machine were provided by Vibro, Argentina private company. Tests with radioactively-contaminated aluminum tubes and a stainless steel bar, were performed at laboratory level. Tests showed that it is possible to clean both the external and the internal surface of contaminated tubes. Results show a decontamination factor around 10 after the first 30 minutes of the cleaning time. (authors)

Effect of Frequency of Brushing Teeth on Plaque and Calculus Accumulation, and Gingivitis in Dogs.

Science.gov (United States)

Harvey, Colin; Serfilippi, Laurie; Barnvos, Donald

2015-01-01

The efficacy of brushing the teeth of beagle dogs in a randomized, controlled, blinded study design using a clearly-defined brushing technique was evaluated for 4 brushing frequencies: brushing daily, brushing every other day, brushing weekly and brushing every other week, compared with no brushing in a control group of dogs. All dogs were fed a standard dry kibble diet during the study. Standard plaque, calculus, and gingivitis indices were used to score the teeth. A 'clean tooth' model was used. No gingival or non-gingival lacerations or other signs of injury to oral tissues were found at the end of the 28 day trial period. Brushing more frequently had greater effectiveness in retarding accumulation of plaque and calculus, and reducing the severity of pre-existing gingivitis. Brushing daily or every other day produced statistically significant improved results compared with brushing weekly or every other week. Based on the results of this study, daily brushing is recommended.

Tooth brushing, tongue cleaning and snacking behaviour of dental technology and therapist students

Directory of Open Access Journals (Sweden)

Clement C. Azodo

2010-08-01

Full Text Available Objective: To determine the tooth brushing, tongue cleaning and snacking behaviour of dental technology and therapist students. Methods: A descriptive cross-sectional study of students of Federal School of Dental Therapy and Technology Enugu, Nigeria. Self-administered questionnaire was used to obtain information on demography, frequency, duration and technique of tooth brushing and tongue cleaning as well as information on consumption of snacks. Results: A total of 242 students responded. Dental technology students made up 52.5% of the respondents and dental therapist in training made up 47.5%. Majority (63.2% of the respondents considered the strength of tooth brush when purchasing a tooth brush and 78.9% use tooth brushes with medium strength. Seven-tenth (71.9% of the respondents brush their teeth twice daily and 52.1% brush for 3–5 minutes. About one-third (30.2% brush their teeth in front of a mirror. Chewing stick was used by 51.7% of respondents in addition to the use of tooth brush. Tongue cleaning was done by 94.2% with only 9.5% using a tongue cleaner. Only 20.2% reported regular snacks consumption. Nine-tenth (90.4% of respondents were previously involved in educating others, apart from their colleagues, on tooth brushing. Conclusion: This survey revealed that most of the dental therapy and technology students had satisfactory tooth-brushing behaviour. The zeal to educate others about proper tooth brushing revealed in this study suggests that the students may be helpful in oral health promotion.

Spontaneous bending of 2D molecular bottle-brush

NARCIS (Netherlands)

Subbotin, A; Jong, J; ten Brinke, G

Using a scaling approach we consider a 2D comb copolymer brush under bending deformations. We show that the rectilinear brush is locally stable and can be characterized by a persistence length lambda increasing with the molecular weight of grafting side chains as lambda similar to M-3. A bending

Nanocryl Coating of PMMA Complete Denture Base Materials to Prevent Scratching.

Science.gov (United States)

Fathi, Hawa M; Benonn, Hajer A; Johnson, Anthony

2017-09-01

The surface of polymethylmethacrylate (PMMA) is vulnerable to indentation by hard objects that may contribute to abrade the material surface and subject it to wear. This phenomenon promotes an increase in the surface roughness leading to microbial colonisation which can endanger the general health of wearers and damage the intra-oral prosthesis. The aim of this study is to investigate the effect of three different nanocryl coating agents (Easy Glaze, G-Coat Plus and Formulation XP) on surface roughness and thickness of PMMA material after a simulating cleaning process utilizing an electric toothbrush and three different dentifrices (pastes and immersion). Acrylic uncoated discs were used as a control group. The results showed that the G-Coat Plus coating agent had less changes in the surface roughness and thickness layer whereas the immersion cleaner revealed less abrasion effect compared with the paste cleaners which could be considered the most suitable cleaner to provide lower abrasivenes and good removal of organic debris. However, using nanofilled sealants did not demonstrate significant improvement in reducing surface roughness p ⟩ 0.05. Nevertheless, it could provide some protection against wearing to the acrylic resin surface during tooth brushing and may provide better resistance to microbial colonisation. Copyright© 2017 Dennis Barber Ltd.

Pleurectomy versus pleural abrasion for primary spontaneous pneumothorax in children.

Science.gov (United States)

Joharifard, Shahrzad; Coakley, Brian A; Butterworth, Sonia A

2017-05-01

Primary spontaneous pneumothorax (PSP) represents a common indication for urgent surgical intervention in children. First episodes are often managed with thoracostomy tube, whereas recurrent episodes typically prompt surgery involving apical bleb resection and pleurodesis, either via pleurectomy or pleural abrasion. The purpose of this study was to assess whether pleurectomy or pleural abrasion was associated with lower postoperative recurrence. The records of patients undergoing surgery for PSP between February 2005 and December 2015 were retrospectively reviewed. Recurrence was defined as an ipsilateral pneumothorax requiring surgical intervention. Bivariate logistic regressions were used to identify factors associated with recurrence. Fifty-two patients underwent 64 index operations for PSP (12 patients had surgery for contralateral pneumothorax, and each instance was analyzed separately). The mean age was 15.7±1.2years, and 79.7% (n=51) of patients were male. In addition to apical wedge resection, 53.1% (n=34) of patients underwent pleurectomy, 39.1% (n=25) underwent pleural abrasion, and 7.8% (n=5) had no pleural treatment. The overall recurrence rate was 23.4% (n=15). Recurrence was significantly lower in patients who underwent pleurectomy rather than pleural abrasion (8.8% vs. 40%, p<0.01). In patients who underwent pleural abrasion without pleurectomy, the relative risk of recurrence was 2.36 [1.41-3.92, p<0.01]. Recurrence of PSP is significantly reduced in patients undergoing pleurectomy compared to pleural abrasion. Level III, retrospective comparative therapeutic study. Copyright © 2017 Elsevier Inc. All rights reserved.

Alcohol versus brush PRK: visual outcomes and adverse effects.

Science.gov (United States)

Sia, Rose K; Ryan, Denise S; Stutzman, Richard D; Psolka, Maximilian; Mines, Michael J; Wagner, Melvin E; Weber, Eric D; Wroblewski, Keith J; Bower, Kraig S

2012-08-01

A smooth corneal surface prior to laser ablation is important in order to achieve a favorable refractive outcome. In this study, we compare PRK outcomes following two commonly used methods of epithelial debridement: Amoils epithelial scrubber (brush) versus 20% ethanol (alcohol). We reviewed records of patients who underwent wavefront-optimized PRK for myopia or myopic astigmatism between January 2008 and June 2010. Two treatment groups (brush vs. alcohol) were compared in terms of uncorrected distance visual acuity (UDVA), manifest refraction spherical equivalent (MRSE), corrected distance visual acuity (CDVA), and complications at postoperative months 1, 3, 6, and 12. One thousand five hundred ninety-three eyes of 804 patients underwent PRK during the study period: 828 brush-treated eyes and 765 alcohol-treated eyes. At 6 months postoperatively UDVA was ≥20/20 in 94.7% of brush-treated eyes versus 94.4% of alcohol-treated eyes (P = 0.907). At 1 month a higher percentage of brush-treated eyes maintained or gained one or more lines CDVA compared to alcohol-treated eyes (P = 0.007), but there were no other differences in UDVA, MRSE, or CDVA at any point postoperatively. At 1 month 75.4% of brush-treated eyes versus 70.4% of alcohol-treated eyes were free of complications (P = 0.032), and there were fewer brush-treated eyes with corneal haze (4.0% vs. 6.9%, P = 0.012) and dry eye (8.9% vs. 14.4%, P = 0.001). Although corneal haze was slightly more frequent in the alcohol group, most was trace and not significant. Although alcohol-assisted PRK had more minor complications in the early postoperative period, including corneal haze and dry eye, results for both groups beyond 1 month were comparable. Copyright © 2012 Wiley Periodicals, Inc.

Shroud brushing device

International Nuclear Information System (INIS)

Sakamaki, Kazuo; Takabayashi, Jun-ichi.

1996-01-01

A roller screw is assembled at an axial center of the inside of a device main body. A nut is assembled to the axial center of the roller screw secured so as not to be rotated, and a base is integrally connected to the nut. An air cylinder is pivoted to the base by a pin, and an arm is disposed to a piston rod of the air cylinder. The top end of the arm is secured to a motor case, and a brush is rotated by an electric motor in the motor case. The device main body is suspended into the reactor pressure vessel of a BWR type reactor, and seated on the upper surface of a fuel support metal fitting. The roller screw is rotated to move vertically the arm by way of the nut and the base. The device main body is rotated to rotate the arm. The arm is extended and then the electric motor is driven to rotate the brush thereby polishing the inner surface of the shroud. (I.N.)

Shroud brushing device

Energy Technology Data Exchange (ETDEWEB)

Sakamaki, Kazuo; Takabayashi, Jun-ichi

1996-07-12

A roller screw is assembled at an axial center of the inside of a device main body. A nut is assembled to the axial center of the roller screw secured so as not to be rotated, and a base is integrally connected to the nut. An air cylinder is pivoted to the base by a pin, and an arm is disposed to a piston rod of the air cylinder. The top end of the arm is secured to a motor case, and a brush is rotated by an electric motor in the motor case. The device main body is suspended into the reactor pressure vessel of a BWR type reactor, and seated on the upper surface of a fuel support metal fitting. The roller screw is rotated to move vertically the arm by way of the nut and the base. The device main body is rotated to rotate the arm. The arm is extended and then the electric motor is driven to rotate the brush thereby polishing the inner surface of the shroud. (I.N.)

Daylong Effect of Tooth Brushing or Combination Tooth Brushing and Tongue Cleaning Using Antiplaque®Toothpaste on Volatile Sulphur Compound Levels

Directory of Open Access Journals (Sweden)

Indriasti Indah Wardhany

2013-07-01

Full Text Available Objective: to determine the daylong effect of Antiplaque® toothpaste active copound and the effect of tooth brushing or combination of tooth brushing and tongue cleaning on Volatile Sulphur Compounds (VSC levels. Methods: Clinical experimental double blinded microbiological and clinical examination. Subjects mainly from dental faculty student with or without a chief complain of halitosis. One hundred and twenty subjects were divided into four groups that consist of thirty samples each group. Two group are treatment subjects were divided into four groups that consist thirty samples each group. Two groups are treatment groups using Antiplaque® toothpaste and two groups are control groups using placebo toothpaste. The daylong effects of VSC levels are measured by Halimeter and organoleptic. The intraoral status were measured including periodontal status and tongue index. Result: There are a reduction of VSC levels in both treatment and control group, but the reduction only significant in group using Antiplaque® toothpaste (Wilcoxon signed rank test, p<0.05. There are a reduction of VSC levels in both treatment using Antiplaque® toothpaste, but the combination of tooth brushing and tongue cleaning reduced VSC levels significantly lower than tooth brushing treatment (Mann Whitney U test, P,0.05. Conclusion: Tooth brushing and tongue cleaning using Antiplaque® toothpaste significantly reduced VSC levels.DOI: 10.14693/jdi.v16i2.95

Projectile Nose Mass Abrasion of High-Speed Penetration into Concrete

Directory of Open Access Journals (Sweden)

Haijun Wu

2012-01-01

Full Text Available Based on the dynamic spherical cavity expansion theory of concrete and the analysis of experimental data, a mass abrasion model of projectile considering the hardness of aggregates, the relative strength of target and projectile, and the initial impact velocity is constructed in this paper. Furthermore, the effect of mass abrasion on the penetration depth of projectile and the influence of hardness of aggregates and strength of projectile on penetration depth and mass loss are also analyzed. The results show that, for the ogive-nose projectile with the CRH of 3 and aspect ratio of 7 penetrating the concrete of 35 MPa, the “rigid-body penetration” model is available when the initial impact velocity is lower than 800 m/s. However, when the initial impact velocity is higher than 800 m/s, the “deforming/eroding body penetration” model should be adopted. Through theoretical analysis and numerical calculation, the results indicate that the initial impact velocity is the most important factor of mass abrasion. The hardness of aggregates and the strength of projectile are also significant factors. But relatively speaking, the sensitivity of strength of projectile to mass abrasion is higher, which indicates that the effect of projectile material on mass abrasion is more dramatic than the hardness of aggregates.

Fouling-resistant polymer brush coatings

KAUST Repository

Thérien-Aubin, Héloïse

2011-11-01

A major problem to be addressed with thin composite films used in processes such as coatings or water purification is the biofouling of the surface. To address this problem in a model system, functionalized polyaramide membranes containing an atom transfer radical polymerization (ATRP) initiator were synthesized as a versatile approach to easily modify the surface properties of the polyaramide. Poly(methacrylic acid) brushes were grown using surface initiated ATRP followed by the functionalization of the poly(methacrylic acid) brushes with different side-chains chosen to reduce adhesion between the membrane and foulant. The relation between membrane fouling and the physicochemical properties of the surface was investigated in detail. © 2011 Elsevier Ltd. All rights reserved.

Fouling-resistant polymer brush coatings

KAUST Repository

Thé rien-Aubin, Hé loï se; Chen, Lin; Ober, Christopher K.

2011-01-01

A major problem to be addressed with thin composite films used in processes such as coatings or water purification is the biofouling of the surface. To address this problem in a model system, functionalized polyaramide membranes containing an atom transfer radical polymerization (ATRP) initiator were synthesized as a versatile approach to easily modify the surface properties of the polyaramide. Poly(methacrylic acid) brushes were grown using surface initiated ATRP followed by the functionalization of the poly(methacrylic acid) brushes with different side-chains chosen to reduce adhesion between the membrane and foulant. The relation between membrane fouling and the physicochemical properties of the surface was investigated in detail. © 2011 Elsevier Ltd. All rights reserved.

Radiocesium movement in a gray rabbit brush community

International Nuclear Information System (INIS)

Klepper, B.; Rogers, L.E.; Hedlund, J.D.; Schreckhise, R.G.; Price, K.R.

1978-01-01

Gray rabbit brush, Chrysothamnus nauseosus (Compositae), is the dominant shrub on disturbed land surfaces on much of the Energy Research and Development Administration's Hanford Reservation in south-central Washington State. A stand of rabbit brush growing on an inactive liquid-waste-disposal crib was studied. Thirty percent of the shrubs showed low but detectable radiation levels in a field survey. The primary radionuclide was 137 Cs. The source of 137 Cs in shrubs was the gravel drain field in the crib, at least 2.4 m below the surface, which was the approximate maximum depth of penetration of rabbit brush taproots. Cesium-137 was observed in roots of certain rabbit brush plants, in the upper 1 cm of soil, and in litter beneath contaminated plants but was not detectable in soil samples taken at depths of 15, 50, 100, and 150 cm. Invertebrates associated with a contaminated shrub showed higher concentrations of 137 Cs than did wider-ranging species. Two of seven pocket mice trapped on the crib contaminated detectable amounts of 137 Cs

Design optimization of a brush turbine with a cleaner/water based solution

Science.gov (United States)

Kim, Rhyn H.

1995-01-01

Recently, a turbine-brush was analyzed based on the energy conservation and the force momentum equation with an empirical relationship of the drag coefficient. An equation was derived to predict the rotational speed of the turbine-brush in terms of the blade angle, number of blades, rest of geometries of the turbine-brush and the incoming velocity. Using the observed flow conditions, drag coefficients were determined. Based on the experimental values as boundary conditions, the turbine-brush flows were numerically simulated to understand first the nature of the flows, and to extend the observed drag coefficient to a flow without holding the turbine-brush.

Baking soda as an abrasive in toothpastes: Mechanism of action and safety and effectiveness considerations.

Science.gov (United States)

Hara, Anderson T; Turssi, Cecilia P

2017-11-01

Toothpastes can be formulated with different abrasive systems, depending on their intended clinical application. This formulation potentially affects their effectiveness and safety and, therefore, requires proper understanding. In this article, the authors focused on abrasive aspects of toothpastes containing sodium bicarbonate (baking soda), which have gained considerable attention because of their low abrasivity and good compatibility, while providing clinical effectiveness (further detailed in the other articles of this special issue). The authors first appraised the role of toothpaste abrasivity on tooth wear, exploring some underlying processes and the existing methods to determine toothpaste abrasivity. The authors reviewed the available data on the abrasivity of toothpastes containing baking soda and reported a summary of findings highlighting the clinical implications. On the basis of the collected evidence, baking soda has an intrinsic low-abrasive nature because of its comparatively lower hardness in relation to enamel and dentin. Baking soda toothpastes also may contain other ingredients, which can increase their stain removal effectiveness and, consequently, abrasivity. Even those formulations have abrasivity well within the safety limit regulatory agencies have established and, therefore, can be considered safe. Copyright © 2017 American Dental Association. Published by Elsevier Inc. All rights reserved.

Demonstration experience with an abrasive blasting technique for decontaminating concrete pads

International Nuclear Information System (INIS)

Devgun, J.S.; Land, R.R.; Doane, R.W.

1990-01-01

A demonstration was performed for decontaminating a radioactivity contaminated concrete pad with a portable abrasive blasting system. The system utilizes a rotating blast wheel that scours the concrete surface with metal abrasive. The metal abrasive, pulverized concrete dust, and contaminants rebound into a separator chamber. The reusable metal abrasive is recycled, and the pulverized media are removed to an integral dust collection system. The exhaust is HEPA filtered to minimize release of airborne contaminants. However, the technique had limited success in reducing contamination around the cracks and seams in the concrete where the higher activity levels of contamination were detected during the radiological survey before the cleanup. The technique can be successful and cost-effective in decontaminating large areas of low contamination; however, careful characterization and planning are necessary. 3 refs., 3 figs., 1 tabs

Abrasion behavior of graphite pebble in lifting pipe of pebble-bed HTR

Energy Technology Data Exchange (ETDEWEB)

Shen, Ke; Su, Jiageng [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Zhou, Hongbo [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Chinergy Co., LTD., Beijing 100193 (China); Peng, Wei; Liu, Bing [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Yu, Suyun, E-mail: suyuan@tsinghua.edu.cn [Center for Combustion Energy, The Key Laboratory for Thermal Science and Power Engineering, Ministry of Educations, Tsinghua University, Beijing 10084 (China)

2015-11-15

Highlights: • Quantitative determination of abrasion rate of graphite pebbles in different lifting velocities. • Abrasion behavior of graphite pebble in helium, air and nitrogen. • In helium, intensive collisions caused by oscillatory motion result in more graphite dust production. - Abstract: A pebble-bed high-temperature gas-cooled reactor (pebble-bed HTR) uses a helium coolant, graphite core structure, and spherical fuel elements. The pebble-bed design enables on-line refueling, avoiding refueling shutdowns. During circulation process, the pebbles are lifted pneumatically via a stainless steel lifting pipe and reinserted into the reactor. Inevitably, the movement of the fuel elements as they recirculate in the reactor produces graphite dust. Mechanical wear is the primary source of graphite dust production. Specifically, the sources are mechanisms of pebble–pebble contact, pebble–wall (structural graphite) contact, and fuel handling (pebble–metal abrasion). The key contribution to graphite dust production is from the fuel handling system, particularly from the lifting pipe. During pneumatic lift, graphite pebbles undergo multiple collisions with the stainless steel lifting pipe, thereby causing abrasion of the graphite pebbles and producing graphite dust. The present work explored the abrasion behavior of graphite pebble in the lifting pipe by measuring the abrasion rate at different lifting velocities. The abrasion rate of the graphite pebble in helium was found much higher than those in air and nitrogen. This gas environment effect could be explained by either tribology behavior or dynamic behavior. Friction testing excluded the possibility of tribology reason. The dynamic behavior of the graphite pebble was captured by analysis of the audio waveforms during pneumatic lift. The analysis results revealed unique dynamic behavior of the graphite pebble in helium. Oscillation and consequently intensive collisions occur during pneumatic lift, causing

Lung scintigraphy evaluation in workers exposed to abrasive dusts

International Nuclear Information System (INIS)

Terra Filho, Mario

1995-01-01

The production process of abrasives use aluminium, or silicon carbide a synthetic material with a hardness only slightly less than that of a diamond. It is popularly known as carborundum since it was first manufactured as an abrasive in 1891, produced by the fusion of high grade silica and petroleum coke with sawdust. For many years silicon carbide was thought not to give rise to pulmonary lesions. Recently several researchers suggested the existence of a carborundum pneumoconiosis. The aim of this study was to evaluate the role of the pulmonary clearance of 99m Technetium chelated to diethylene-triamine penta-acetate ( 99m Tc DTPA), and 67 Gallium lung scanning in workers exposed to abrasive dusts. Thirty seven subjects, 13 smokers and 24 nonsmokers and ex smokers were studied. In 32 (86,48%) 67 Gallium lung scanning was positive including 13 (40,62%) retired workers. We conclude that non smoking workers of abrasives plants have a pulmonary alveolar epithelial permeability disturbance similar as observed in smoking workers and smoking controls. Most workers, ex-workers of these industries and in patients with carborundum pneumoconiosis there is an evidence of pulmonary inflammation measured with abnormal 67 Gallium lung scan. (author)

Keep Kids' Mouths Healthy: Brush 2min2X

Science.gov (United States)

Make sure your kids brush for 2 minutes, twice a day. En Español facebook twitter instagram Kids’ Healthy Mouths Health Watch & Brush! Watch ... About Kids’ Teeth Teeth Helpful Resources Links Keep Kids’ Mouths Healthy Roll over or click the time ...

Measurement of nanoparticle removal by abrasion

International Nuclear Information System (INIS)

Guiot, Arnaud; Golanski, Luana; Tardif, Francois

2009-01-01

A strong release limitation of single nanoparticles from commercial manufactured 'nanoproducts' is necessary to decrease potential exposure risks of consumers and represents also a pragmatic way to facilitate acceptance for nanomaterial commercialization before obtaining definitive toxicological results. So, it is of prime importance to know how to characterize the release of small materials during usage solicitations such as mechanical, thermal, UV stress: are they single nanoparticles, aggregates or nanoparticles included in a bigger piece of the matrix? In the frame of NanoSafe2 project, CEA developed and qualified a specific bench test where the material to be tested is mechanically solicited by abrasion using a normalized Taber equipment. The first results show that nanofillers can be released in usage by abrasion for non optimised nanoproducts.

Numerical analysis of special-shaped surface in abrasive flow machining

Science.gov (United States)

Li, Junye; Zhou, Zengwei; Wu, Guiling; Lu, Hui; Sun, Zhihuai

2018-03-01

Solid-liquid two-phase abrasive flow machining is a method to effectively polish the surface of Special-shaped surface parts. Based on the processing characteristics of the abrasive flow machining. The standard model and the pressure-coupled SIMPLEC algorithm are used. The shear force and velocity of the near-wall surface of the runner of the solid-liquid two-phase abrasive machining with different inlet pressure are analyzed. The numerical simulation results show that the inlet pressure has little effect on the velocity, and the shear force has a linear relationship with the inlet pressure. To obtain a better polishing effect, the outlet pressure can be appropriately increased.

Influence of Corrosion on the Abrasion of Cutter Steels Used in TBM Tunnelling

Science.gov (United States)

Espallargas, N.; Jakobsen, P. D.; Langmaack, L.; Macias, F. J.

2015-01-01

Abrasion on tunnel boring machine (TBM) cutters may be critical in terms of project duration and costs. Several researchers are currently studying the degradation of TBM cutter tools used for excavating hard rock, soft ground and loose soil. So far, the primary focus of this research has been directed towards abrasive wear. Abrasive wear is a very common process in TBM excavation, but with a view to the environment in which the tools are working, corrosion may also exert an influence. This paper presents a selection of techniques that can be used to evaluate the influence of corrosion on abrasion on TBM excavation tools. It also presents the influence of corrosion on abrasive wear for some initial tests, with constant steel and geomaterial and varying properties of the excavation fluids (soil conditioners, anti-abrasion additives and water). The results indicate that the chloride content in the water media greatly influences the amount of wear, providing evidence of the influence of corrosion on the abrasion of the cutting tools. The presence of conditioning additives tailored to specific rock or soil conditions reduces wear. However, when chloride is present in the water, the additives minimise wear rates but fail to suppress corrosion of the cutting tools.

Shoe heel abrasion and its possible biomechanical cause: a transversal study with infantry recruits.

Science.gov (United States)

Baumfeld, Daniel; Raduan, Fernando C; Macedo, Benjamim; Silva, Thiago Alexandre Alves; Baumfeld, Tiago; Favato, Danilo Fabrino; de Andrade, Marco Antonio Percope; Nery, Caio

2015-11-19

Excessive shoe heel abrasion is of concern to patients and shoe manufacturers, but little scientific information is available about this feature and its possible causes. The purpose of this study was to relate this phenomenon with biomechanical factors that could predispose to shoe heel abrasion. Ninety-seven recruits (median age 25) were enrolled in this study. Shoe abrasion was assessed manually with a metric plastic tape on the posterior part of the heel that comes in contact with the ground. The number of sprains, foot alignment, and calf muscle shortening (Silfverskiold test) was also assessed in order to relate it with shoe heel abrasion. After using our exclusion criteria, 86 recruits and 172 were considered for this study. The most common abrasion site was the lateral portion of the heel surface (50 %). Forty-four percent of the participants had neutral hind-foot alignment and 39 % had valgus alignment. Twenty-six (30 %) patients have had previous ankle or foot sprains. Neutral foot was related with less calf muscle shortening. On the other hand, valgus hind-foot alignment was more associated with Achilles shortening (p study was able to correlate shoe heel abrasion with biomechanical causes (neutral alignment-uniform abrasion/varus alignment-central and lateral abrasion). More effort has to be done to continue evaluating outsole abrasion with its possible biomechanical cause in order to predict and treat possible associated injuries.

A comparison of terahertz-pulsed imaging with transverse microradiography and microhardness to measure mineral changes in enamel after treatment with fluoride dentifrices

Science.gov (United States)

Churchley, David; Lippert, Frank; Lynch, Richard; Alton, Jesse; Gonzalez-Cabezas, C.; Eder, J.

2009-02-01

The aim of this study was to determine the ability of Terahertz Pulsed Imaging (TPI) to measure mineral changes in enamel lesions during de/remineralisation studies. A comparison was made between transverse microradiography (TMR) and microhardness measurements. Artificial lesions were formed in bovine enamel using a solution of 0.1 M lactic acid (pH 5.0) containing 0.2% Carbopol C907 and 50% saturated with hydroxyapatite. The 20 day experimental protocol consisted of four, one-minute treatment periods with dentifrices containing 10, 675, 1385 and 2700ppm fluoride, a 4 h/day acid challenge, and for the remaining time specimens were stored in a 50:50 pooled human / artificial saliva mixture. Terahertz images were generated by positioning the specimens at the focus of the beam and raster scanning the optics to collect the reflections from the air / enamel (AEI) and lesion / enamel (LEI) interface. Significant differences were observed in the intensity change from baseline of the AEI and LEI reflections upon treatment with the four dentifrices. A linear correlation was observed between ΔAEI vs ΔVHN (r2 = 0.997), ΔAEI vs ΔKHN (r2 =0.964), ΔII (ratio of LEI to AEI) vs ΔΔZ (r2 =0.875) and ΔLEI vs ΔΔZ (r2 =0.870). Statistically significant correlations (ptechnology to measure in vitro (and possibly in situ) mineral changes in enamel and is sufficiently sensitive to discriminate between the levels of remineralization produced by the different dentifrices.

Submerged cutting of steel by abrasive water jets

International Nuclear Information System (INIS)

Haferkamp, H.; Louis, H.; Meier, G.

1990-01-01

A special cutting head for underwater use was designed and built. Tests were carried out to find out useful parameters for submerged cutting. With regard to the production of secondary waste the abrasive flow rate had to be minimized. This was achieved by using a small water jet nozzle (up to 0.4 mm diameter) and a high pressure (up to 4000 bar) with an optimal abrasive flow rate of about 5 g/s. In the case of a higher ambient pressure a decrease of the cutting performance was measured. But this decrease is not important regarding decommissioning because the ambient pressure is less than 2 bar. An air mantle nozzle was adapted to the cutting head to improve the working distance under water. The air mantle surrounding the abrasive jet lowers the friction between jet and surrounding water and increases the cutting efficiency in the case of greater working distances. (author)

Technology of magnetic abrasive finishing in machining of difficult-to-machine alloy complex surface

Directory of Open Access Journals (Sweden)

Fujian MA

2016-10-01

Full Text Available The technology of magnetic abrasive finishing is one of the important finishing technologies. Combining with low-frequency vibration and ultrasonic vibration, it can attain higher precision, quality and efficiency. The characteristics and the related current research of magnetic abrasive finishing, vibration assisted magnetic abrasive finishing and ultrasonic assisted magnetic abrasive finishing are introduced. According to the characteristics of the difficult-to-machine alloy's complex surface, the important problems for further study are presented to realize the finishing of complex surface with the technology of magnetic abrasive finishing, such as increasing the machining efficiency by enhancing the magnetic flux density of machining gap and compounding of magnetic energy and others, establishing of the control function during machining and the process planning method for magnetic abrasive finishing of complex surface under the space geometry restraint of complex surface on magnetic pole, etc.

Study of Effect of Impacting Direction on Abrasive Nanometric Cutting Process with Molecular Dynamics.

Science.gov (United States)

Li, Junye; Meng, Wenqing; Dong, Kun; Zhang, Xinming; Zhao, Weihong

2018-01-11

Abrasive flow polishing plays an important part in modern ultra-precision machining. Ultrafine particles suspended in the medium of abrasive flow removes the material in nanoscale. In this paper, three-dimensional molecular dynamics (MD) simulations are performed to investigate the effect of impacting direction on abrasive cutting process during abrasive flow polishing. The molecular dynamics simulation software Lammps was used to simulate the cutting of single crystal copper with SiC abrasive grains at different cutting angles (0 o -45 o ). At a constant friction coefficient, we found a direct relation between cutting angle and cutting force, which ultimately increases the number of dislocation during abrasive flow machining. Our theoretical study reveal that a small cutting angle is beneficial for improving surface quality and reducing internal defects in the workpiece. However, there is no obvious relationship between cutting angle and friction coefficient.

Single-chain-in-mean-field simulations of weak polyelectrolyte brushes

Science.gov (United States)

Léonforte, F.; Welling, U.; Müller, M.

2016-12-01

Structural properties of brushes which are composed of weak acidic and basic polyelectrolytes are studied in the framework of a particle-based approach that implicitly accounts for the solvent quality. Using a semi-grandcanonical partition function in the framework of the Single-Chain-in-Mean-Field (SCMF) algorithm, the weak polyelectrolyte is conceived as a supramolecular mixture of polymers in different dissociation states, which are explicitly treated in the partition function and sampled by the SCMF procedure. One obtains a local expression for the equilibrium acid-base reaction responsible for the regulation of the charged groups that is also incorporated to the SCMF sampling. Coupled to a simultaneous treatment of the electrostatics, the approach is shown to capture the main features of weak polyelectrolyte brushes as a function of the bulk pH in the solution, the salt concentration, and the grafting density. Results are compared to experimental and theoretical works from the literature using coarse-grained representations of poly(acrylic acid) (PAA) and poly(2-vinyl pyridine) (P2VP) polymer-based brushes. As the Born self-energy of ions can be straightforwardly included in the numerical approach, we also study its effect on the local charge regulation mechanism of the brush. We find that its effect becomes significant when the brush is dense and exposed to high salt concentrations. The numerical methodology is then applied (1) to the study of the kinetics of collapse/swelling of a P2VP brush and (2) to the ability of an applied voltage to induce collapse/swelling of a PAA brush in a pH range close to the pKa value of the polymer.

Uptake of pH-Sensitive Gold Nanoparticles in Strong Polyelectrolyte Brushes

Directory of Open Access Journals (Sweden)

Dikran Kesal

2016-04-01

Full Text Available The impact of electrostatic attraction on the uptake of gold nanoparticles (AuNPs into positively charged strong poly-[2-(Methacryloyloxy ethyl] trimethylammonium chloride (PMETAC polyelectrolyte brushes was investigated. In this work, PMETAC brushes were synthesized via surface-initiated atom transfer radical polymerization (Si-ATRP. PMETAC/AuNP composite materials were prepared by incubation of the polymer brush coated samples into 3-mercaptopropionic acid-capped AuNP (5 nm in diameter suspension. The electrostatic interactions were tuned by changing the surface charge of the AuNPs through variations in pH value, while the charge of the PMETAC brush was not affected. Atomic-force microscopy (AFM, ellipsometry, UV/Vis spectroscopy, gravimetric analysis and transmission electron microscopy (TEM were employed to study the loading and penetration into the polymer brush. The results show that the number density of attached AuNPs depends on the pH value and increases with increasing pH value. There is also strong evidence that the particle assembly is dependent on the pH value of the AuNP suspension. Incubation of PMETAC brushes in AuNP suspension at pH 4 led to the formation of a surface layer on top of the brush (2D assembly due to sterical hindrance of the clustered AuNPs, while incubation in AuNP suspension at pH 8 led to deeper particle penetration into the brush (3D assembly. The straightforward control of particle uptake and assembly by tuning the charge density of the nanoparticle surface is a valuable tool for the development of materials for colorimetric sensor applications.

Functional patterns obtained by nanoimprinting lithography and subsequent growth of polymer brushes

International Nuclear Information System (INIS)

Genua, A; AlduncIn, J A; Pomposo, J A; Grande, H; Kehagias, N; Reboud, V; Sotomayor, C; Mondragon, I; Mecerreyes, D

2007-01-01

In this work the growth of polymer brushes was combined with nanoimprint lithography (NIL) in order to obtain new functional nanopatterns. First, a functional thermoplastic methacrylic copolymer poly(methyl methacrylate-co-2-bromoisobutyryl-oxy-ethyl methacrylate) was synthesized. This copolymer was successfully patterned by NIL using a silicon stamp at 160 deg. C and 60 bar. Next, hydrophilic polymer brushes based on poly(3-sulfopropylmethacrylate) and hydrophobic polymer brushes based on a poly(fluorinated methacrylate) were grown on the imprinted surfaces. The surface properties of the patterned polymer were accordingly modified and, as a consequence, the water contact angle was modified from 80.3 deg. to 32.5 deg. in the case of the hydrophilic brushes and to 118.1 deg. in the case of the hydrophobic brushes. As an application we demonstrated the use of hydrophobic polymer brushes in order to modify the surface of polymeric stamps for NIL with self-demoulding properties

Dendritic brushes under theta and poor solvent conditions

Science.gov (United States)

Gergidis, Leonidas N.; Kalogirou, Andreas; Charalambopoulos, Antonios; Vlahos, Costas

2013-07-01

The effects of solvent quality on the internal stratification of polymer brushes formed by dendron polymers up to third generation were studied by means of molecular dynamics simulations with Langevin thermostat. The distributions of polymer units, of the free ends, the radii of gyration, and the back folding probabilities of the dendritic spacers were studied at the macroscopic states of theta and poor solvent. For high grafting densities we observed a small decrease in the height of the brush as the solvent quality decreases. The internal stratification in theta solvent was similar to the one we found in good solvent, with two and in some cases three kinds of populations containing short dendrons with weakly extended spacers, intermediate-height dendrons, and tall dendrons with highly stretched spacers. The differences increase as the grafting density decreases and single dendron populations were evident in theta and poor solvent. In poor solvent at low grafting densities, solvent micelles, polymeric pinned lamellae, spherical and single chain collapsed micelles were observed. The scaling dependence of the height of the dendritic brush at high density brushes for both solvents was found to be in agreement with existing analytical results.

Galectin-4 and small intestinal brush border enzymes form clusters

DEFF Research Database (Denmark)

Danielsen, E M; van Deurs, B

1997-01-01

that galectin-4 is indeed an intestinal brush border protein; we also localized galectin-4 throughout the cell, mainly associated with membraneous structures, including small vesicles, and to the rootlets of microvillar actin filaments. This was confirmed by subcellular fractionation, showing about half...... by a nonclassical pathway, and the brush border enzymes represent a novel class of natural ligands for a member of the galectin family. Newly synthesized galectin-4 is rapidly "trapped" by association with intracellular structures prior to its apical secretion, but once externalized, association with brush border......Detergent-insoluble complexes prepared from pig small intestine are highly enriched in several transmembrane brush border enzymes including aminopeptidase N and sucrase-isomaltase, indicating that they reside in a glycolipid-rich environment in vivo. In the present work galectin-4, an animal lectin...

Experience of racism and tooth brushing among pregnant Aboriginal Australians: exploring psychosocial mediators.

Science.gov (United States)

Ben, J; Jamieson, L M; Priest, N; Parker, E J; Roberts-Thomson, K F; Lawrence, H P; Broughton, J; Paradies, Y

2014-09-01

Despite burgeoning evidence regarding the pathways by which experiences of racism influence health outcomes, little attention has been paid to the relationship between racism and oral health-related behaviours in particular. We hypothesised that self-reported racism was associated with tooth brushing, and that this association was mediated by perceived stress and sense of control and moderated by social support. Data from 365 pregnant Aboriginal Australian women were used to evaluate tooth brushing behaviour, sociodemographic factors, psychosocial factors, general health, risk behaviours and racism exposure. Bivariate associations were explored and hierarchical logistic regression models estimated odds ratios (OR) and 95% confidence intervals (CI) for tooth brushing. Perceived stress and sense of control were examined as mediators of the association between self-reported racism and tooth brushing using binary mediation with bootstrapping. High levels of self-reported racism persisted as a risk indicator for tooth brushing (OR 0.51, 95%CI 0.27,0.98) after controlling for significant covariates. Perceived stress mediated the relationship between self-reported racism and tooth brushing: the direct effect of racism on tooth brushing was attenuated, and the indirect effect on tooth brushing was significant (beta coefficient -0.09; bias-corrected 95%CI -0.166,-0.028; 48.1% of effect mediated). Sense of control was insignificant as a mediator of the relationship between racism and tooth brushing. High levels of self-reported racism were associated with non-optimal tooth brushing behaviours, and perceived stress mediated this association among this sample of pregnant Aboriginal women.. Limitations and implications are discussed.

Experimental Investigation on the Material Removal of the Ultrasonic Vibration Assisted Abrasive Water Jet Machining Ceramics

Directory of Open Access Journals (Sweden)

Tao Wang

2017-01-01

Full Text Available The ultrasonic vibration activated in the abrasive water jet nozzle is used to enhance the capability of the abrasive water jet machinery. The experiment devices of the ultrasonic vibration assisted abrasive water jet are established; they are composed of the ultrasonic vibration producing device, the abrasive supplying device, the abrasive water jet nozzle, the water jet intensifier pump, and so on. And the effect of process parameters such as the vibration amplitude, the system working pressure, the stand-off, and the abrasive diameter on the ceramics material removal is studied. The experimental result indicates that the depth and the volume removal are increased when the ultrasonic vibration is added on abrasive water jet. With the increase of vibration amplitude, the depth and the volume of material removal are also increased. The other parameters of the ultrasonic vibration assisted abrasive water jet also have an important role in the improvement of ceramic material erosion efficiency.

Brushes and soap : grafted polymers and their interactions with nanocolloids

OpenAIRE

Currie, E.P.K.

2000-01-01

Layers of polymer chains end-attached to a grafting plane at high densities, so-called brushes, are a curious state of matter. The (average) monomer density within the brush is as high as in a semi-dilute polymer solution, resulting in a high osmotic pressure in the brush. Due to the grafting, however, this isotropic osmotic pressure results in an anisotropic stretching of the chains normal to the surface. This degree of stretching can be quite extensive; in this thesis PEO-chains of...

Current control by a homopolar machine with moving brushes

International Nuclear Information System (INIS)

Vogel, H.

1978-01-01

The equation for TNS Doublet's E-coil circuit with moving brush homopolar machine is integrated in the flux of the homopolar for a monotonically increasing current function extending beyond the current reversal into the burn period. The results show that the moving brush feature is not useful for controlling the burn

The Effects of a Brushing Procedure on Stereotypical Behavior

Science.gov (United States)

Davis, Tonya N.; Durand, Shannon; Chan, Jeffrey M.

2011-01-01

In this study we analyzed the effects of a brushing protocol on stereotyped behavior of a young boy with autism. First, a functional analysis was conducted which showed that the participant's stereotypy was maintained by automatic reinforcement. Next, the Wilbarger Protocol, a brushing intervention, was implemented. An ABA design was implemented…

Effects of Bristle Hardness & Duration of Manual Tooth brushing on Plaque Control

Directory of Open Access Journals (Sweden)

. Sunny

2017-03-01

Full Text Available Background: Oral health is an integral part of general health. Poor oral health can have adverse effect on general health hence a good oral health is very essential, which in turn is achieved by good oral hygiene. Even though, the concept of good oral hygiene evolved 5000 years back, it is only in the beginning of 19th century it gained more importance. (1 Dental caries and periodontal disease are the most commonly occurring diseases affecting mankind. Dental plaque is a very important factor in the causation of both the diseases. (2 Aims & Objectives: To evaluate efficacy of four different types of toothbrushes, with difference in duration of brushing along with different bristle hardness in removal of microbial plaque. Material & Methods: In a randomized controlled trial, four groups with 40 subjects used manual toothbrushes with either hard, medium, soft and ultra-soft bristles. On baseline examination, clinical parameter plaque index (Sillness & Loe, 1964 was recorded. Selected subjects were refrained from all kinds of oral hygiene measures for 24 hrs before clinical appointment. On the day of clinical appointment scores of pre and post brushing were recorded in each patient when brushing time was set for 1 minute and same procedure was repeated after a wash off period of 3 days and similar recordings were made with brushing time of 11/2minute. Primary outcome was measured with differences in the plaque index (Sillness & Loe, 1964 compared to baseline. Results: Significant reduction in mean value of plaque score was observed on comparing pre-brushing and post-brushing data in all the subjects irrespective of bristle hardness in both 1 minute and 11/2 minute groups. On increasing time duration from 1 minute to 11/2 minute intergroup comparison revealed that significant correlation exist in mean plaque score reduction in subjects using medium bristle brush, soft bristle brush, ultra-soft bristle brush. However, no significant reduction in

Trends in Social Inequality in Tooth Brushing among Adolescents: 1991-2014

DEFF Research Database (Denmark)

Holstein, Bjørn Evald; Bast, Lotus Sofie; Brixval, Carina Sjöberg

2015-01-01

This study examines whether social inequality in tooth brushing frequency among adolescents changed from 1991 to 2014. The data material was seven comparable cross-sectional studies of nationally representative samples of 11- to 15-year-olds in Denmark with data about frequency of tooth brushing...... and occupation of parents. The total number of participants was 31,464, of whom 21.7% brushed their teeth less than the recommended 2 times a day. The absolute social inequality measured as prevalence difference between low and high social class increased from 7.7% in 1991 to 14.6% in 2014. The relative social...... inequality assessed by odds ratios for infrequent tooth brushing also increased from 1991 to 2014....

Synergy of brushing mode and antibacterial use on in vivo biofilm formation.

Science.gov (United States)

Jongsma, Marije A; van de Lagemaat, Marieke; Busscher, Henk J; Geertsema-Doornbusch, Gesinda I; Atema-Smit, Jelly; van der Mei, Henny C; Ren, Yijin

2015-12-01

Orthodontic, multi-strand retention-wires are used as a generalized model for oral retention sites to investigate whether biofilm left-behind after powered toothbrushing in-vivo enabled better penetration of antibacterials as compared with manual brushing. 2-cm multi-strand, stainless-steel retention-wires were placed in brackets bonded bilaterally in the upper arches of 10-volunteers. Volunteers used NaF-sodium-lauryl-sulphate-containing toothpaste and antibacterial, triclosan-containing toothpaste supplemented or not with an essential-oils containing mouthrinse. Opposite sides of the dentition including the retention-wires, were brushed manually or with a powered toothbrush. Health-care-regimens were maintained for 1-week, after which wires were removed and oral biofilm was collected. When powered toothbrushing was applied, slightly less bacteria were collected than after manual brushing, regardless whether an antibacterial-regimen was used or not. Powered-toothbrushing combined with antibacterial-regimens yielded lower biofilm viability than manual brushing, indicating better antibacterial penetration into biofilm left-behind after powered brushing. Major shifts in biofilm composition, with a decrease in prevalence of both cariogenic species and periodontopathogens, were induced after powered brushing using an antibacterial-regimen. Oral biofilm left-behind after powered brushing in-vivo enabled better penetration of antibacterials than after manual brushing. Mechanical removal of oral biofilm is important for prevention of dental pathologies, but biofilm is always left-behind, such as in fissures, buccal pits, interproximal areas and gingival margins and around orthodontic appliances. Use of antibacterial toothpastes or mouthrinses can contribute to removal or killing of biofilm bacteria, but biofilm structure hampers antibacterial penetration. A synergy between brushing mode and antibacterial-regimen applied exists with clinically demonstrable effects

Plaque-left-behind after brushing: intra-oral reservoir for antibacterial toothpaste ingredients.

Science.gov (United States)

Otten, Marieke P T; Busscher, Henk J; Abbas, Frank; van der Mei, Henny C; van Hoogmoed, Chris G

2012-10-01

Plaque is never fully removed by brushing and may act as a reservoir for antibacterial ingredients, contributing to their substantive action. This study investigates the contribution of plaque-left-behind and saliva towards substantivity of three antibacterial toothpastes versus a control paste without antibacterial claims. First, volunteers brushed 2 weeks with a control or antibacterial toothpaste. Next, plaque and saliva samples were collected 6 and 12 h after brushing and bacterial concentrations and viabilities were measured. The contributions of plaque and saliva towards substantivity were determined by combining control plaques with experimental plaque or saliva samples and subsequently assessing their viabilities. Bacterial compositions in the various plaque and saliva samples were compared using denaturing gradient gel electrophoresis. The viabilities of plaques after brushing with Colgate-Total® and Crest-Pro-Health® were smaller than of control plaques and up to 12 h after brushing with Crest-Pro-Health® plaques still contained effective, residual antibacterial activity against control plaques. No effective, residual antibacterial activity could be measured in saliva samples after brushing. There was no significant difference in bacterial composition of plaque or saliva after brushing with the different toothpastes. Plaque-left-behind after mechanical cleaning contributes to the substantive action of an antibacterial toothpaste containing stannous fluoride (Crest-Pro-Health®). The absorptive capacity of plaque-left-behind after brushing is of utmost clinical importance, since plaque is predominantly left behind in places where its removal and effective killing matter most. Therewith this study demonstrates a clear and new beneficial effect of the use of antibacterial toothpastes.

Evaluation of brushing cytology in the diagnosis of Helicobacter pylori gastritis

Directory of Open Access Journals (Sweden)

Amir Ahmad Mostaghni

2008-02-01

Full Text Available Background: Helicobacter pylori (HP is the cause of the most common infection in the world. It has been recognized as the major cause of peptic ulcer and an important risk factor for gastric malignancy. A variety of reliable methods are available for detecting HP during upper gastrointestinal endoscopy. Rapid urease test (RUT is the cheapest method and histology is the most expensive brush cytology is faster and cheaper than histology. Methods: The brushing cytology materials were obtained from the antrum of the stomach in 109 patients who suffered from dyspepsia and were candidates for endoscopy. The RUT and histology with hematoxylin-eosin staining were also performed on each patient separately. The infection status for each patient was established by a concordance of two test results. Results: Seventy-eight of 100 patients (78% were diagnosed as positive for Helicobacter pylori organisms using brushing cytology. The sensitivity and specificity of brushing cytology were 96% and 72% respectively. Sensitivity of brush cytology (96% was higher than RUT (77.4%, and RUT was more specific than histology (100% vs 90%. Conclusion: Gastric brushing cytology provides an accurate, inexpensive and easy technique in the rapid detection of Helicobacter pylori infection. When additional information about the severity of mucosal damage or the presence of cell atypias is not necessary, histologic examination can be omitted, and a cost effective strategy for assessing HP status might consist of taking antral biopsies, the former for RUT and performing brush cytology slide, which should be stained and examined only when the RUT result is negative.

Quantitative characterization of agglomerate abrasion in a tumbling blender by using the Stokes number approach.

Science.gov (United States)

Willemsz, Tofan A; Nguyen, Tien Thanh; Hooijmaijers, Ricardo; Frijlink, Henderik W; Vromans, Herman; van der Voort Maarschalk, Kees

2013-03-01

Removal of microcrystalline cellulose agglomerates in a dry-mixing system (lactose, 100 M) predominantly occurs via abrasion. The agglomerate abrasion rate potential is estimated by the Stokes abrasion (StAbr) number of the system. The StAbr number equals the ratio between the kinetic energy density of the moving powder bed and the work of fracture of the agglomerate. Basically, the StAbr number concept describes the blending condition of the dry-mixing system. The concept has been applied to investigate the relevance of process parameters on agglomerate abrasion in tumbling blenders. Here, process parameters such as blender rotational speed and relative fill volumes were investigated. In this study, the StAbr approach revealed a transition point between abrasion rate behaviors. Below this transition point, a blending condition exists where agglomerate abrasion is dominated by the kinetic energy density of the powder blend. Above this transition point, a blending condition exists where agglomerates show (undesirable) slow abrasion rates. In this situation, the blending condition is mainly determined by the high fill volume of the filler.

Microsecond MD Simulations of Nano-patterned Polymer Brushes on Self-Assembled Monolayers

Science.gov (United States)

Buie, Creighton; Qiu, Liming; Cheng, Kwan; Park, Soyeun

2010-03-01

Nano-patterned polymer brushes end-grafted onto self-assembled monolayers have gained increasing research interests due to their unique thermodynamic properties and their chemical and biomedical applications in colloids, biosensing and tissue engineering. So far, the interactions between the polymer brushes with the surrounding environments such as the floor and solvent at the nanometer length scale and microsecond time scale are still difficult to obtained experimentally and computationally. Using a Coarse-Grained MD approach, polymer brushes of different monomeric lengths, grafting density and hydrophobicity of the monomers grafted on self-assembled monolayers and in explicit solvent were studied. Molecular level information, such as lateral diffusion, transverse height and volume contour of the brushes, were calculated from our microsecond-MD simulations. Our results demonstrated the significance of the hydration of the polymer in controlling the conformational arrangement of the polymer brushes.

Impact Capacity Reduction in Railway Prestressed Concrete Sleepers with Surface Abrasions

Science.gov (United States)

Ngamkhanong, Chayut; Li, Dan; Kaewunruen, Sakdirat

2017-10-01

Railway sleepers (also called ‘railroad tie’ in North America) embedded in ballasted railway tracks are a main part of railway track structures. Its important role is to transfer the loads evenly from the rails to a wider area of ballast bed and to secure rail gauge and enable safe passages of rolling stocks. By nature, railway infrastructure is nonlinear, evidenced by its behaviours, geometry and alignment, wheel-rail contact and operational parameters such as tractive efforts. Based on our critical review, the dynamic behaviour of railway sleepers has not been fully investigated, especially when the sleepers are deteriorated by excessive wears. In fact, the ballast angularity causes differential abrasions on the soffit or bottom surface of sleepers (especially at railseat zone). Furthermore, in sharp curves and rapid gradient change, longitudinal and lateral dynamics of rails increase the likelihood of railseat abrasions in concrete sleepers due to the unbalanced loading conditions. This paper presents a structural capacity of concrete sleepers under dynamic transient loading. The modified compression field theory for ultimate strength design of concrete sleepers under impact loading will be highlighted in this study. The influences of surface abrasions, including surface abrasion and soffit abrasion, on the dynamic behaviour of prestressed concrete sleepers, are firstly highlighted. The outcome of this study will improve the rail maintenance and inspection criteria in order to establish appropriate and sensible remote track condition monitoring network in practice. Moreover, this study will also improve the understanding of the fundamental dynamic behaviour of prestressed concrete sleepers with surface abrasions. The insight into these behaviours will not only improve safety and reliability of railway infrastructure but will enhance the structural safety of other concrete structures.

Refractory, Abrasive and Other Industrial Mineral Operations

Data.gov (United States)

Department of Homeland Security — This map layer includes refractory, abrasive, and other industrial minerals operations in the United States. The data represent commodities covered by the Minerals...

Neural network approximation of tip-abrasion effects in AFM imaging

International Nuclear Information System (INIS)

Bakucz, Peter; Dziomba, Thorsten; Koenders, Ludger; Krüger-Sehm, Rolf; Yacoot, Andrew

2008-01-01

The abrasion (wear) of tips used in scanning force microscopy (SFM) directly influences SFM image quality and is therefore of great relevance to quantitative SFM measurements. The increasing implementation of automated SFM measurement schemes has become a strong driving force for increasing efforts towards the prediction of tip wear, as it needs to be ensured that the probe is exchanged before a level of tip wear is reached that adversely affects the measurement quality. In this paper, we describe the identification of tip abrasion in a system of SFM measurements. We attempt to model the tip-abrasion process as a concatenation of a mapping from the measured AFM data to a regression vector and a nonlinear mapping from the regressor space to the output space. The mapping is formed as a basis function expansion. Feedforward neural networks are used to approximate this mapping. The one-hidden layer network gave a good quality of fit for the training and test sets for the tip-abrasion system. We illustrate our method with AFM measurements of both fine periodic structures and randomly oriented sharp features and compare our neural network results with those obtained using other methods

Neural network approximation of tip-abrasion effects in AFM imaging

Science.gov (United States)

Bakucz, Peter; Yacoot, Andrew; Dziomba, Thorsten; Koenders, Ludger; Krüger-Sehm, Rolf

2008-06-01

The abrasion (wear) of tips used in scanning force microscopy (SFM) directly influences SFM image quality and is therefore of great relevance to quantitative SFM measurements. The increasing implementation of automated SFM measurement schemes has become a strong driving force for increasing efforts towards the prediction of tip wear, as it needs to be ensured that the probe is exchanged before a level of tip wear is reached that adversely affects the measurement quality. In this paper, we describe the identification of tip abrasion in a system of SFM measurements. We attempt to model the tip-abrasion process as a concatenation of a mapping from the measured AFM data to a regression vector and a nonlinear mapping from the regressor space to the output space. The mapping is formed as a basis function expansion. Feedforward neural networks are used to approximate this mapping. The one-hidden layer network gave a good quality of fit for the training and test sets for the tip-abrasion system. We illustrate our method with AFM measurements of both fine periodic structures and randomly oriented sharp features and compare our neural network results with those obtained using other methods.

Evaluation of multi-brush anode systems in microbial fuel cells

KAUST Repository

Lanas, Vanessa; Logan, Bruce E.

2013-01-01

), the number of brushes connected in parallel, and the wire current collector gage. MFCs with different numbers of brushes (one, three or six) set perpendicular to the cathode all produced similar power densities (1200±40mW/m2) and coulombic efficiencies (60

Molecular Design of Antifouling Polymer Brushes Using Sequence-Specific Peptoids.

Science.gov (United States)

Lau, King Hang Aaron; Sileika, Tadas S; Park, Sung Hyun; Sousa, Ana Maria Leal; Burch, Patrick; Szleifer, Igal; Messersmith, Phillip B

2015-01-07

Material systems that can be used to flexibly and precisely define the chemical nature and molecular arrangement of a surface would be invaluable for the control of complex biointerfacial interactions. For example, progress in antifouling polymer biointerfaces that prevent non-specific protein adsorption and cell attachment, which can significantly improve the performance of an array of biomedical and industrial applications, is hampered by a lack of chemical models to identify the molecular features conferring their properties. Poly(N-substituted glycine) "peptoids" are peptidomimetic polymers that can be conveniently synthesized with specific monomer sequences and chain lengths, and are presented as a versatile platform for investigating the molecular design of antifouling polymer brushes. Zwitterionic antifouling polymer brushes have captured significant recent attention, and a targeted library of zwitterionic peptoid brushes with a different charge densities, hydration, separations between charged groups, chain lengths, and grafted chain densities, is quantitatively evaluated for their antifouling properties through a range of protein adsorption and cell attachment assays. Specific zwitterionic brush designs were found to give rise to distinct but subtle differences in properties. The results also point to the dominant roles of the grafted chain density and chain length in determining the performance of antifouling polymer brushes.

Minimum free-energy paths for the self-organization of polymer brushes.

Science.gov (United States)

Gleria, Ignacio; Mocskos, Esteban; Tagliazucchi, Mario

2017-03-22

A methodology to calculate minimum free-energy paths based on the combination of a molecular theory and the improved string method is introduced and applied to study the self-organization of polymer brushes under poor solvent conditions. Polymer brushes in a poor solvent cannot undergo macroscopic phase separation due to the physical constraint imposed by the grafting points; therefore, they microphase separate forming aggregates. Under some conditions, the theory predicts that the homogeneous brush and the aggregates can exist as two different minima of the free energy. The theoretical methodology introduced in this work allows us to predict the minimum free-energy path connecting these two minima as well as the morphology of the system along the path. It is shown that the transition between the homogeneous brush and the aggregates may involve a free-energy barrier or be barrierless depending on the relative stability of the two morphologies and the chain length and grafting density of the polymer. In the case where a free-energy barrier exists, one of the morphologies is a metastable structure and, therefore, the properties of the brush as the quality of the solvent is cycled are expected to display hysteresis. The theory is also applied to study the adhesion/deadhesion transition between two opposing surfaces modified by identical polymer brushes and it is shown that this process may also require surpassing a free-energy barrier.

Feasibility Study on Cutting HTPB Propellants with Abrasive Water Jet

Science.gov (United States)

Jiang, Dayong; Bai, Yun

2018-01-01

Abrasive water jet is used to carry out the experiment research on cutting HTPB propellants with three components, which will provide technical support for the engineering treatment of waste rocket motor. Based on the reliability theory and related scientific research results, the safety and efficiency of cutting sensitive HTPB propellants by abrasive water jet were experimentally studied. The results show that the safety reliability is not less than 99.52% at 90% confidence level, so the safety is adequately ensured. The cooling and anti-friction effect of high-speed water jet is the decisive factor to suppress the detonation of HTPB propellant. Compared with pure water jet, cutting efficiency was increased by 5% - 87%. The study shows that abrasive water jets meet the practical use for cutting HTPB propellants.

Oral health knowledge, practice, oral hygiene status, and dental caries prevalence among visually impaired children in Bangalore

OpenAIRE

S T Prashanth; Sudhanshu Bhatnagar; Usha Mohan Das; H Gopu

2011-01-01

Introduction: Visually impaired children daily face challenges for bearing their everyday skills. Maintenance of proper oral hygiene is one among them. Aim: The aim of the study was to assess the oral health knowledge, practice, oral hygiene status, and dental caries prevalence among visually impaired children in Bangalore. Materials and Methods: A total of 85 children were asked verbally a questionnaire regarding the frequency of brushing, cleaning tools, use of dentifrice, knowledge about t...

Quantitative characterization of agglomerate abrasion in a tumbling blender by using the Stokes number approach

NARCIS (Netherlands)

Willemsz, Tofan A.; Nguyen, Tien Thanh; Hooijmaijers, Ricardo; Frijlink, Henderik W.; Vromans, Herman; van der Voort Maarschalk, Kees

2013-01-01

Removal of microcrystalline cellulose agglomerates in a dry-mixing system (lactose, 100 M) predominantly occurs via abrasion. The agglomerate abrasion rate potential is estimated by the Stokes abrasion (StAbr) number of the system. The StAbrnumber equals the ratio between the kinetic energy density

Sweet brushes and dirty proteins

NARCIS (Netherlands)

Bosker, Wouter T. E.; Patzsch, Katja; Stuart, Martien A. Cohen; Norde, Willem

2007-01-01

We studied the protein repellency of dextran brushes. Dextran was grafted to a polystyrene surface in a broad range of grafting densities using polystyrene - dextran block copolymers and the Langmuir - Blodgett deposition technique. Ellipsometry measurements confirmed a successful transfer of the

On the abrasion of heat-treated 2.8C21Cr1Mo white cast iron

Energy Technology Data Exchange (ETDEWEB)

Al-Rubaie, Kassim S.; Preti, Orlando [Centro Universitario SOCIESC, Joinville (Brazil). Engenharia Mecanica; Pohl, Michael [Bochum Univ. (Germany). Inst. fuer Werkstoffe

2016-09-15

The abrasion behaviour of heat-treated 2.8C21Cr1Mo cast iron was studied. The specimens were destabilised at two temperatures, 980 and 1050 C, for 4 h, air hardened, and then tempered at five temperatures, 220, 320, 400, 500, and 620 C, for 2 h followed by air cooling. Using a pin-on-plate abrasion apparatus, the specimens were abraded on four types of bonded abrasives (silicon carbide, corundum, flint, and glass). The effect of work hardening on the abrasion resistance was investigated. It was found that the increase in alloy hardness produced by heat treatment had little effect on the abrasion resistance against silicon carbide or corundum; the inverse was true against flint or glass. The as-hardened structure containing 40% retained austenite gave the best abrasion resistance, whereas the hardened and tempered at 620 C showed the worst. Both bulk hardness and matrix hardness before wear correlated poorly with the abrasion resistance. Therefore, a general model ''equivalent hardness'' was developed, in which the hardness of the abraded matrix was considered. With this model, the abrasion behaviour can be clearly analysed.

46 CFR 108.187 - Ventilation for brush type electric motors in classified spaces.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Ventilation for brush type electric motors in classified... Ventilation for brush type electric motors in classified spaces. Ventilation for brush type electric motors in... Electrical Equipment in Hazardous Locations”, except audible and visual alarms may be used if shutting down...

Dimeric assembly of enterocyte brush border enzymes

DEFF Research Database (Denmark)

Danielsen, E M

1994-01-01

The noncovalent, dimeric assembly of small intestinal brush border enzymes was studied by sedimentation analysis in density gradients of extracts of pulse-labeled pig jejunal mucosal explants. Like aminopeptidase N (EC 3.4.11.2), sucrase-isomaltase (EC 3.2.1.48-10), aminopeptidase A (EC 3...... appearance of the liposome-reconstituted enzyme [Norén et al. (1986) J. Biol. Chem. 261, 12306-12309], showing only the inner, membrane-anchored domains of the monomers to be in close contact with one another while the outer domains are far apart. In contrast to the other brush border enzymes studied...

Photochemical surface modification of PP for abrasion resistance

International Nuclear Information System (INIS)

Bahners, Thomas; Haessler, Ruediger; Gao Shanglin; Maeder, Edith; Wego, Andreas; Schollmeyer, Eckhard

2009-01-01

The potential of a photo-chemical approach to increase the surface hardness of polypropylene (PP) has been studied. Using a 222 nm excimer lamp, fibers and film were irradiated in the presence of multi-functional substances diallylphthalate (DAP), tetraallyloxyethane (TAE), and pentaerithritoltriacylate (PETA) and characterized with regard to the resulting effect on abrasion resistance. AFM-based methods were employed to analyze thermo-mechanical surface properties. Nanoindentation and microthermal analyses of the outermost surface layers of UV treated fibers gave clear indications of an effective cross-linking of reactive substances present during irradiation. One may assume that the reactive media polymerize on top of the surface of the PP substrate and form a thin-layer. The abrasion resistance of the PP fibers was tested by applying stress through a rotating and axially oscillating roller of defined roughness and measuring the mass loss as a function of time. The abrasion resistance was found to be remarkably improved compared to the untreated fiber. Best effects were achieved using PETA as reactive substance. The experiments clearly showed the influence of processing conditions, namely with regard to homogeneous coverage of the substrate surface with the reactive medium.

Experimental Study of the Ultrasonic Vibration-Assisted Abrasive Waterjet Micromachining the Quartz Glass

Directory of Open Access Journals (Sweden)

Rongguo Hou

2018-01-01

Full Text Available The ultrasonic vibration is used to enhance the capability of the abrasive water micromachining glass. And, the ultrasonic vibration is activated on the abrasive waterjet nozzle. The quality of the flow is improved, and the velocity of the abrasive is increased because of the addition of the ultrasonic energy. The relevant experimental results indicate that the erosion depth and the material volume removal of the glass are obviously increased when ultrasonic vibration is working. As for the influence of process parameters on the material removal of the glass such as vibration amplitude, system pressure, distance of the standoff, and abrasive size, the experimental results indicate that the system pressure and vibration contribute greatly to the glass material removal. Also, the erosion depth and the volume of material removal are increased with the increase in the vibration amplitude and system pressure. There are some uplifts found at the edge of erosion pit. Then, it can be inferred that the plastic method is an important material removal method during the machining process of ultrasonic vibration-assisted abrasive waterjet.

A new method to test rock abrasiveness based on physico-mechanical and structural properties of rocks

Directory of Open Access Journals (Sweden)

V.N. Oparin

2015-06-01

Full Text Available A new method to test rock abrasiveness is proposed based upon the dependence of rock abrasiveness on their structural and physico-mechanical properties. The article describes the procedure of presentation of properties that govern rock abrasiveness on a canonical scale by dimensionless components, and the integrated estimation of the properties by a generalized index. The obtained results are compared with the known classifications of rock abrasiveness.

Vision, healing brush, and fiber bundles

Science.gov (United States)

Georgiev, Todor

2005-03-01

The Healing Brush is a tool introduced for the first time in Adobe Photoshop (2002) that removes defects in images by seamless cloning (gradient domain fusion). The Healing Brush algorithms are built on a new mathematical approach that uses Fibre Bundles and Connections to model the representation of images in the visual system. Our mathematical results are derived from first principles of human vision, related to adaptation transforms of von Kries type and Retinex theory. In this paper we present the new result of Healing in arbitrary color space. In addition to supporting image repair and seamless cloning, our approach also produces the exact solution to the problem of high dynamic range compression of17 and can be applied to other image processing algorithms.

Kinetic energy density and agglomerate abrasion rate during blending of agglomerates into powders.

Science.gov (United States)

Willemsz, Tofan A; Hooijmaijers, Ricardo; Rubingh, Carina M; Tran, Thanh N; Frijlink, Henderik W; Vromans, Herman; van der Voort Maarschalk, Kees

2012-01-23

Problems related to the blending of a cohesive powder with a free flowing bulk powder are frequently encountered in the pharmaceutical industry. The cohesive powder often forms lumps or agglomerates which are not dispersed during the mixing process and are therefore detrimental to blend uniformity. Achieving sufficient blend uniformity requires that the blending conditions are able to break up agglomerates, which is often an abrasion process. This study was based on the assumption that the abrasion rate of agglomerates determines the required blending time. It is shown that the kinetic energy density of the moving powder bed is a relevant parameter which correlates with the abrasion rate of agglomerates. However, aspects related to the strength of agglomerates should also be considered. For this reason the Stokes abrasion number (St(Abr)) has been defined. This parameter describes the ratio between the kinetic energy density of the moving powder bed and the work of fracture of the agglomerate. The St(Abr) number is shown to predict the abrasion potential of agglomerates in the dry-mixing process. It appeared possible to include effects of filler particle size and impeller rotational rate into this concept. A clear relationship between abrasion rate of agglomerates and the value of St(Abr) was demonstrated. Copyright © 2011 Elsevier B.V. All rights reserved.

A novel approach for UV-patterning with binary polymer brushes.

Science.gov (United States)

Li, Lifu; Nakaji-Hirabayashi, Tadashi; Kitano, Hiromi; Ohno, Kohji; Saruwatari, Yoshiyuki; Matsuoka, Kazuyoshi

2018-01-01

A mixed self-assembled monolayer (SAM) of an initiator (3-(2-bromo-2-isobutyryloxy)propyl triethoxysilane) for atom transfer radical polymerization (ATRP) and an agent (6-(triethoxysilyl)hexyl 2-(((methylthio)carbonothioyl)thio)-2-phenylacetate) for reversible addition-fragmentation chain transfer (RAFT) polymerization was constructed on the surface of a silicon wafer or glass plate by a silane coupling reaction. When a UV light at 254nm was irradiated at the mixed SAM through a photomask, the surface density of the bromine atom at the end of BPE in the irradiated region was drastically reduced by UV-driven scission of the BrC bond, as observed by X-ray photoelectron spectroscopy. Consequently, the surface-initiated (SI)-ATRP of 2-ethylhexyl methacrylate (EHMA) was used to easily construct the poly(EHMA) (PEHMA) brush domain. Subsequently, SI-RAFT polymerization of a zwitterionic vinyl monomer, carboxymethyl betaine (CMB), was performed. Using the sequential polymerization, the PCMB and PEHMA brush domains on the solid substrate could be very easily patterned. Patterning proteins and cells with the binary polymer brush is expected because the PCMB brush indicated strong suppression of protein adsorption and cell adhesion, and the PEHMA brush had non-polar properties. This technique is very simple and useful for regulating the shape and size of bio-fouling and anti-biofouling domains on solid surfaces. Copyright © 2017 Elsevier B.V. All rights reserved.

Molecular Velcro constructed from polymer loop brushes showing enhanced adhesion force

Science.gov (United States)

Zhou, Tian; Han, Biao; Han, Lin; Li, Christopher; Department of Materials Science; Engineering Team; School of Biomedical Engineering, Science; Health Systems Team

2015-03-01

Molecular Velcro is commonly seen in biological systems as the formation of strong physical entanglement at molecular scale could induce strong adhesion, which is crucial to many biological processes. To mimic this structure, we designed, and fabricated polymer loop brushes using polymer single crystals with desired surface functionality and controlled chain folding. Compared with reported loop brushes fabricated using triblock copolymers, the present loop bushes have precise loop sizes, loop grafting density, and well controlled tethering locations on the solid surface. Atomic force microscopy-based force spectroscopy measurements using a polymer chain coated probe reveal that the adhesion force are significantly enhanced on the loop brush surface as compared with its single-strand counterpart. This study directly shows the effect of polymer brush conformation on their properties, and suggests a promising strategy for advanced polymer surface design.

Performance Enhancement of Abrasive Waterjet Cutting

NARCIS (Netherlands)

2008-01-01

Abrasive Waterjet (AWJ) Machining is a recent non-traditional machining process. This technology is widely used in industry for cutting difficult-to-machine-materials, milling slots, polishing hard materials etc. AWJ machining has many advantages, e.g. it can cut net-shape parts, no heat is

Probing endocytosis from the enterocyte brush border using fluorescent lipophilic dyes

DEFF Research Database (Denmark)

Danielsen, E Michael

2015-01-01

The small intestinal brush border is a specialized cell membrane that needs to withstand the solubilizing effect of bile salts during assimilation of dietary nutrients and to achieve detergent resistance; it is highly enriched in glycolipids organized in lipid raft microdomains. In the present work......-toluenesulfonate), and CellMask Orange plasma membrane stain were used to study endocytosis from the enterocyte brush border of organ-cultured porcine mucosal explants. All the dyes readily incorporated into the brush border but were not detectably endocytosed by 5 min, indicating a slow uptake compared with other cell types...

Comparison of Three types of Tooth Brushes on Plaque and Gingival Indices: A Randomized Clinical Trial.

Science.gov (United States)

Moeintaghavi, Amir; Sargolzaie, Naser; Rostampour, Mehrnoosh; Sarvari, Sara; Kargozar, Sanaz; Gharaei, Shideh

2017-01-01

To compare clinical results of three types of manual tooth brushes on plaque removal efficacy and gingivitis. This study is a single blind randomized trial with crossover design which involved 30 periodontaly healthy individuals. Professional plaque removal and oral hygiene instruction were performed for all the participants in the first step of our study followed by asking them to avoid brushing for 2 days. Thereafter plaque and gingivitis scores were measured using plaque and gingival indices (PI and GI). Then subjects were instructed to use Pulsar tooth brush for a two-week period and then, GI and PI indices were assessed again. After passing one-week period for wash out, subjects didn't brush for 2 days and indices were recorded again. The same procedure was done for CrossAction, and Butler 411 tooth brushes respectively and at the end of the study these variables were analyzed using SPSS software ver.16. Repeated measurement ANOVA test was used to compare the scores between different brushes. Finding of this study reveals that using all three types of tooth brushes resulted in significant plaque and gingivitis reduction compared to baseline levels. Pulsar tooth brush was significantly more effective in diminishing PI and GI than Butler tooth brush (p=0.044 and 0.031 respectively). According to our findings all 3 types of tooth brushes are effective in reduction of plaque and gingivitis and this reduction is significantly greater for Pulsar tooth brush compared to Butler and CrossAction tooth brushes.

Unconventional ordering behavior of semi-flexible polymers in dense brushes under compression.

Science.gov (United States)

Milchev, Andrey; Binder, Kurt

2014-06-07

Using a coarse-grained bead-spring model for semi-flexible macromolecules which form a polymer brush, the structure and dynamics of the polymers were investigated, varying the chain stiffness and the grafting density. The anchoring conditions for the grafted chains were chosen such that their first bonds were oriented along the normal to the substrate plane. The compression of such a semi-flexible brush by a planar piston was observed to be a two-stage process: for a small compression the chains were shown to contract by "buckling" deformation whereas for a larger compression the chains exhibited a collective (almost uniform) bending deformation. Thus, the stiff polymer brush underwent a 2nd order phase transition of collective bond reorientation. The pressure, required to keep the stiff brush at a given degree of compression, was thereby significantly smaller than for an otherwise identical brush made of entirely flexible polymer chains! While both the brush height and the chain linear dimensions in the z-direction perpendicular to the substrate increased monotonically with an increase in the chain stiffness, the lateral (xy) chain linear dimensions exhibited a maximum at an intermediate chain stiffness. Increasing the grafting density led to a strong decrease of these lateral dimensions which is compatible with an exponential decay. Also the recovery kinetics after removal of the compressing piston were studied, and were found to follow a power-law/exponential decay with time. A simple mean-field theoretical consideration, accounting for the buckling/bending behavior of semi-flexible polymer brushes under compression was suggested.

Electrical resistivity measurements to predict abrasion resistance

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 31; Issue 2. Electrical resistivity measurements to predict abrasion resistance of rock aggregates ... It was seen that correlation coefficients were increased for the rock classes. In addition ...

Abrasion Wear Resistance, Hardness and Microstructure of Hard Linings Deposited by Means of a Submerged Arc. Dureza, microestructura y resistencia al desgaste por abrasion de recargues duros depositados con arco sumergido

Energy Technology Data Exchange (ETDEWEB)

Paranhos, R; Alcoforado, J M; Castillo, J A; Sauer, A

1989-01-01

Consumable materials for submerged arc welding of the types alloyed flux-neutral electrode and neutral flux-alloyed electrode were used to form, through multipass welding, a light alloy hard lining of the C-Mn type on ASTM A36 Type structural steel. Emphasis was put on microstructural characterization of the linings surveyed under electron scanning microscopy, and tests were performed to study their hardness and abrasion wear resistance at low pressures. As a result of these tests, a great influence of welding parameters on hardness and abrasion resistance properties of the combination active flux-neutral electrode was noticed. As the results showed no relationship between the hardness and the abrasion wear resistance of the linings surveyed, an attempt was made to relate the resulting microstructure with their abrasion wear resistance. (Author)

Characterization of Conventional and High-Translucency Y-TZP Dental Ceramics Submitted to Air Abrasion.

Science.gov (United States)

Tostes, Bhenya Ottoni; Guimarães, Renato Bastos; Noronha-Filho, Jaime Dutra; Botelho, Glauco Dos Santos; Guimarães, José Guilherme Antunes; Silva, Eduardo Moreira da

2017-01-01

This study evaluated the effect of air-abrasion on t®m phase transformation, roughness, topography and the elemental composition of three Y-TZP (Yttria-stabilized tetragonal zirconia polycrystal) dental ceramics: two conventional (Lava Frame and IPS ZirCad) and one with high-translucency (Lava Plus). Plates obtained from sintered blocks of each ceramic were divided into four groups: AS (as-sintered); 30 (air-abrasion with 30 mm Si-coated Al2O3 particles); 50 (air-abrasion with 50 mm Al2O3 particles) and 150 (air-abrasion with 150 mm Al2O3 particles). After the treatments, the plates were submitted to X-ray diffractometry; 3-D profilometry and SEM/EDS. The AS surfaces were composed of Zr and t phases. All treatments produced t®m phase transformation in the ceramics. The diameter of air-abrasion particles influenced the roughness (150>50>30>AS) and the topography. SEM analysis showed that the three treatments produced groove-shaped microretentions on the ceramic surfaces, which increased with the diameter of air-abrasion particles. EDS showed a decrease in Zr content along with the emergence of O and Al elements after air-abrasion. Presence of Si was also detected on the plates air-abraded with 30 mm Si-coated Al2O3 particles. It was concluded that irrespective of the type and diameter of the particles, air-abrasion produced t®m phase transformation, increased the roughness and changed the elemental composition of the three Y-TZP dental ceramics. Lava Plus also behaved similarly to the conventional Y-TZP ceramics, indicating that this high translucency ceramic could be more suitable to build monolithic ceramic restorations in the aesthetic restorative dentistry field.

Salt dependence of compression normal forces of quenched polyelectrolyte brushes

Science.gov (United States)

Hernandez-Zapata, Ernesto; Tamashiro, Mario N.; Pincus, Philip A.

2001-03-01

We obtained mean-field expressions for the compression normal forces between two identical opposing quenched polyelectrolyte brushes in the presence of monovalent salt. The brush elasticity is modeled using the entropy of ideal Gaussian chains, while the entropy of the microions and the electrostatic contribution to the grand potential is obtained by solving the non-linear Poisson-Boltzmann equation for the system in contact with a salt reservoir. For the polyelectrolyte brush we considered both a uniformly charged slab as well as an inhomogeneous charge profile obtained using a self-consistent field theory. Using the Derjaguin approximation, we related the planar-geometry results to the realistic two-crossed cylinders experimental set up. Theoretical predictions are compared to experimental measurements(Marc Balastre's abstract, APS March 2001 Meeting.) of the salt dependence of the compression normal forces between two quenched polyelectrolyte brushes formed by the adsorption of diblock copolymers poly(tert-butyl styrene)-sodium poly(styrene sulfonate) [PtBs/NaPSS] onto an octadecyltriethoxysilane (OTE) hydrophobically modified mica, as well as onto bare mica.

Abrasive water jet: a complementary tool

Directory of Open Access Journals (Sweden)

Duarte, J. P.

1998-04-01

Full Text Available The abrasive water jet is a powerful cutting tool, whose main advantages lie in the absence of thermal effects and the capability of cutting highly thick materials. Compared with Laser, the abrasive water jet allows the cutting of a larger range of thicknesses and a wider variety of materials such as: ornamental stones, metals, polymers, composites, wood, glass and ceramics. The application of this technology has suffered an extensive growth, with successful applications in varied industrial sectors like the automotive, aerospace, textile, metalworking, ornamental stones, etc. The present communication aims at introducing the abrasive water jet as a complementary tool to laser cutting, presenting its advantages by showing some documented examples of pieces cut for different industries.

O jacto de água abrasivo é uma poderosa ferramenta de corte, tendo como principais vantagens a ausência de processo térmico e permitir o corte de elevadas espessuras. Comparativamente com o laser o jacto de água abrasivo permite cortar uma maior gama de espessuras, e uma maior diversidade de materiais: rochas ornamentais, metais, polimeros, compósitos, madeiras, vidro e cerâmicos. A aplicação desta tecnologia tem sofrido um crescimento acentuado, existindo aplicações de sucesso nos mais variados sectores industriáis como a indústria automóvel, aeroespacial, têxtil, metalomecânica e rochas ornamentáis. Esta comunição pretende apresentar o corte por jacto de agua abrasivo como uma ferramenta de corte complementar ao corte por laser, apresentando as suas vantagens documentadas através de alguns exemplos de peças executadas para as diferentes indústrias.

Nanostructure of Cationic Polymer Brush at the Air/Water Interface

Directory of Open Access Journals (Sweden)

Matsuoka Hideki

2013-08-01

Full Text Available Cationic amphiphilic diblock copolymers were synthesized by RAFT polymerization and the nanostructure of their monolayers was investigated by π-A isotherm and X-ray reflectivity. Carpet layer (dense hydrophilic block layer formation under the hydrophobic layer was confirmed and a “brush” layer was found beneath the carpet layer. However, the thickness of brush layer was much thinner than that of the fully-stretched chain length. The critical salt concentration was found to be 0.01 M NaCl, which is much lower than that of the previous strongly anionic brush. These differences were probably caused by the low effective charge on the brush chains due to the hydrophobic nature of the quarternized ammonium cation.

Preparing high-density polymer brushes by mechanically assisted polymer assembly (MAPA)

Science.gov (United States)

Wu, Tao; Efimenko, Kirill; Genzer, Jan

2001-03-01

We introduce a novel method of modifying the surface properties of materials. This technique, called MAPA (="mechanically assisted polymer assembly"), is based on: 1) chemically attaching polymerization initiators to the surface of an elastomeric network that has been previously stretched by a certain length, Δx, and 2) growing end-anchored macromolecules using surface initiated ("grafting from") atom transfer living radical polymerization. After the polymerization, the strain is removed from the substrate, which returns to its original size causing the grafted macromolecules to stretch away from the substrate and form a dense polymer brush. We demonstrate the feasibility of the MAPA method by preparing high-density polymer brushes of poly(acryl amide), PAAm. We show that, as expected, the grafting density of the PAAm brushes can be increased by increasing Δx. We demonstrate that polymer brushes with extremely high grafting densities can be successfully prepared by MAPA.

The Art and Science of Polymer Brushes: Recent Developments in Patterning and Characterization Approaches.

Science.gov (United States)

Panzarasa, Guido

2017-06-28

Polymer brushes are dense arrays of macromolecular chains tethered by one end at a surface. They are at the cutting edge of polymer nanotechnology since the dawn of controlled surface-initiated polymerization techniques unlocked new prospects for the synthesis of polymer brushes with tailorable properties. More recently, thanks to the growing interest in the use of brushes for the generation of functional surfaces, the need for advanced patterning and characterization approaches rapidly increased. Meeting these needs requires the contribution of experts from different disciplines: polymer chemistry, surface science, electrochemistry and particle physics. The focus of this review is to highlight recent developments in the field of polymer brushes, specifically the application of photocatalytic lithography as a versatile patterning strategy, the study of grafted-from polymer brushes by electrochemical methods and, most importantly, the introduction of positron annihilation spectroscopy as a powerful technique for the investigation of the structure of polymer brushes and of their composites with nanoparticles.

Release of carbon nanotubes from an epoxy-based nanocomposite during an abrasion process.

Science.gov (United States)

Schlagenhauf, Lukas; Chu, Bryan T T; Buha, Jelena; Nüesch, Frank; Wang, Jing

2012-07-03

The abrasion behavior of an epoxy/carbon nanotube (CNT) nanocomposite was investigated. An experimental setup has been established to perform abrasion, particle measurement, and collection all in one. The abraded particles were characterized by particle size distribution and by electron microscopy. The abrasion process was carried out with a Taber Abraser, and the released particles were collected by a tube for further investigation. The particle size distributions were measured with a scanning mobility particle sizer (SMPS) and an aerodynamic particle sizer (APS) and revealed four size modes for all measured samples. The mode corresponding to the smallest particle sizes of 300-400 nm was measured with the SMPS and showed a trend of increasing size with increasing nanofiller content. The three measured modes with particle sizes from 0.6 to 2.5 μm, measured with the APS, were similar for all samples. The measured particle concentrations were between 8000 and 20,000 particles/cm(3) for measurements with the SMPS and between 1000 and 3000 particles/cm(3) for measurements with the APS. Imaging by transmission electron microscopy (TEM) revealed that free-standing individual CNTs and agglomerates were emitted during abrasion.

Erosion wear of boron carbide ceramic nozzles by abrasive air-jets

International Nuclear Information System (INIS)

Deng Jianxin

2005-01-01

Boron carbide nozzles were produced by hot pressing. The erosion wear of this nozzle caused by abrasive particle impact was investigated by abrasive air-jets. Silica, silicon carbide and alumina powders with different hardness were used as the erodent abrasive particles. Results showed that the hardness of the erodent particles played an important role with respect to the erosion wear of the boron carbide nozzles. As the hardness of the erodent particles increases, there is a dramatic increase in erosion rate of the nozzles. The nozzle entrance area suffered from severe abrasive impact under large impact angles, and generated maximum tensile stresses. The wear mechanisms of boron carbide nozzle at this area appeared to be entirely brittle in nature with the evidence of large scale-chipping, and exhibited a brittle fracture induced removal process. While at the nozzle center wall section, most of the particles traveled parallel to the nozzle wall, and showed minimum tensile stresses. The wear mode in this area of the nozzle changed from impact to sliding erosion, and the wear mechanisms appeared to be the lateral cracking owing to a surface fatigue fracture mechanism

Effect of dried sunflower seeds on incisal edge abrasion: A rare case report.

Science.gov (United States)

Rath, Avita; Ramamurthy, Priyadarshini H; Fernandes, Bennete Aloysius; Sidhu, Preena

2017-01-01

Tooth surface loss (TSL) is a complex phenomenon characterized by the loss of hard tooth structure at various locations of the teeth, usually due to more than one factor. TSL due to abrasion can be significant in patients consuming coarse, abrasive diet. The present case reports an interesting incisal edge abrasion in a female patient, attributed to a particular dietary behavior of long-term consumption of sunflower seeds. All her family members and most of the people from her native place were also reported to have similar lesions by the patient. Larger epidemiological studies to assess the prevalence and severity of such abrasive lesions in geographic areas with this particular dietary habit need to be carried out so that people may be made aware and educated about alternative ways of eating sunflower seeds that will not cause any form of tooth wear.

Strong Stretching of Poly(ethylene glycol) Brushes Mediated by Ionic Liquid Solvation.

Science.gov (United States)

Han, Mengwei; Espinosa-Marzal, Rosa M

2017-09-07

We have measured forces between mica surfaces coated with a poly(ethylene glycol) (PEG) brush solvated by a vacuum-dry ionic liquid, 1-ethyl-3-methyl imidazolium bis(trifluoromethylsulfonyl)imide, with a surface forces apparatus. At high grafting density, the solvation mediated by the ionic liquid causes the brush to stretch twice as much as in water. Modeling of the steric repulsion indicates that PEG behaves as a polyelectrolyte; the hydrogen bonding between ethylene glycol and the imidazolium cation seems to effectively charge the polymer brush, which justifies the strong stretching. Importantly, under strong polymer compression, solvation layers are squeezed out at a higher rate than for the neat ionic liquid. We propose that the thermal fluctuations of the PEG chains, larger in the brush than in the mushroom configuration, maintain the fluidity of the ionic liquid under strong compression, in contrast to the solid-like squeezing-out behavior of the neat ionic liquid. This is the first experimental study of the behavior of a polymer brush solvated by an ionic liquid under nanoconfinement.

Applications of functional polymer brushes for nanoparticle uptake and prevention of protein adsorption

Science.gov (United States)

Arifuzzaman, Shafi M.

The central theme of this Ph.D. dissertation is to develop novel multifunctional polymer coatings for understanding partition of proteins and nanoparticles on polymers grafted to flat surfaces (so-called brushes). Systematic investigation of the adsorption phenomena is accomplished by utilizing surface-anchored assemblies comprising grafted polymers with variation in physical properties (i.e., length or/and grafting density) and chemical functionality. The chemical composition of the brush is tailored by either "chemical coloring" of a parent homopolymer brush with selective chemical moieties or by sequential growth of two chemically dissimilar polymer blocks. We present preparation of two types of tailor-made, surface-grafted copolymers: (1) those composed of hydrophilic and hydrophobic blocks (so-called amphiphilic polymer brushes), and (2) those comprising of anionic and cationic polymer segments (so-called polyampholyte brushes). We describe the organization of functionality in the grafted polymer brushes and the partitioning of proteins and nanoparticles using a battery of complementary analytical probes. Specifically, we address how varying the molecular weight, grafting density, and chemical composition of the brush affects adsorbtion and desorbtion of model proteins and gold nanoparticles. Our observations indicate densely-populated responsive amphiphilic polymers are very efficient in suppressing protein adsorption. In addition, we have established that the length of poly(ethylene glycol) spacers attached to a parent homopolymer brush is a key factor governing uptake of gold nanoparticles. Both grafting density and molecular weight of the coating are important in controlling the kinetics and thermodynamics of protein adsorption on surfaces. Our findings and methodologies can lead to the development of next generation environmentally friendly antifouling surfaces and will find application in medical devices, antifouling coatings and anti reflection finishes.

29 CFR 1915.134 - Abrasive wheels.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Abrasive wheels. 1915.134 Section 1915.134 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... wheels shall fit freely on the spindle and shall not be forced on. The spindle nut shall be tightened...

Calves Use an Automated Brush and a Hanging Rope When Pair-Housed

Directory of Open Access Journals (Sweden)

Gosia Zobel

2017-11-01

Full Text Available Calf housing often only meets the basic needs of calves, but there is a growing interest in providing enrichments. This study described the behaviour of calves when they were given the opportunity to interact with two commonly available enrichment items. Female and male calves (approximately 11 days old were pair-housed in 8 identical pens fitted with an automated brush and a hanging rope. Frequency and duration of behaviours were recorded on 3 separate days (from 12:00 until 08:00 the following day. Calves spent equal time using the brush and rope (27.1 min/day, but there was less variation in the use of the brush as opposed to the rope (coefficient of variation, CV: 23 vs. 78%, respectively. Calves had more frequent (94 bouts, CV: 24% and shorter (17.8 s/bout, CV: 24% brush use bouts compared to fewer (38 bouts, CV: 43% and longer (38.3 s/bout, CV: 53% rope use bouts. There was a diurnal pattern of use for both items. Frequency of play was similar to rope use, but total time playing was 8% of rope and brush use. Variability among calves suggested that individual preference existed; however, the social dynamics of the pair-housed environment were not measured and therefore could have influenced brush and rope use. Multiple enrichment items should be considered when designing improvements to calf housing.

Development of the Upgraded DC Brush Gear Motor for Spacebus Platforms

Science.gov (United States)

Berning, Robert H.; Viout, Olivier

2010-01-01

The obsolescence of materials and processes used in the manufacture of traditional DC brush gear motors has necessitated the development of an upgraded DC brush gear motor (UBGM). The current traditional DC brush gear motor (BGM) design was evaluated using Six-Sigma process to identify potential design and production process improvements. The development effort resulted in a qualified UBGM design which improved manufacturability and reduced production costs. Using Six-Sigma processes and incorporating lessons learned during the development process also improved motor performance for UBGM making it a more viable option for future use as a deployment mechanism in space flight applications.

Review of Artificial Abrasion Test Methods for PV Module Technology

Energy Technology Data Exchange (ETDEWEB)

Miller, David C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Muller, Matt T. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Simpson, Lin J. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-08-01

This review is intended to identify the method or methods--and the basic details of those methods--that might be used to develop an artificial abrasion test. Methods used in the PV literature were compared with their closest implementation in existing standards. Also, meetings of the International PV Quality Assurance Task Force Task Group 12-3 (TG12-3, which is concerned with coated glass) were used to identify established test methods. Feedback from the group, which included many of the authors from the PV literature, included insights not explored within the literature itself. The combined experience and examples from the literature are intended to provide an assessment of the present industry practices and an informed path forward. Recommendations toward artificial abrasion test methods are then identified based on the experiences in the literature and feedback from the PV community. The review here is strictly focused on abrasion. Assessment methods, including optical performance (e.g., transmittance or reflectance), surface energy, and verification of chemical composition were not examined. Methods of artificially soiling PV modules or other specimens were not examined. The weathering of artificial or naturally soiled specimens (which may ultimately include combined temperature and humidity, thermal cycling and ultraviolet light) were also not examined. A sense of the purpose or application of an abrasion test method within the PV industry should, however, be evident from the literature.

Liquid abrasive pressure pot scoping tests report

International Nuclear Information System (INIS)

Archibald, K.E.

1996-01-01

The primary initiatives of the LITCO Decontamination Development group at the Idaho Chemical Process Plant (ICPP) are the development of methods to eliminate the use of sodium bearing decontamination chemicals and minimization of the amount of secondary waste generated during decontamination activities. In July of 1994, a Commerce Business Daily (CBD) announcement was issued by the INEL to determine commercial interest in the development of an in-situ liquid abrasive grit blasting system. As a result of the CBD announcement, Klieber ampersand Schulz issued an Expression of Interest letter which stated they would be interested in testing a prototype Liquid Abrasive Pressure Pot (LAPP). LITCO's Decontamination group and Kleiber ampersand Schulz entered into a Cooperative Research and Development Agreement (CRADA) in which the Decontamination Development group tested the prototype LAPP in a non-radioactive hot cell mockup. Test results are provided

Abrasion Resistance of as-Cast High-Chromium Cast Iron

Directory of Open Access Journals (Sweden)

Pokusová Marcela

2014-12-01

Full Text Available High chromium cast irons are widely used as abrasion resistant materials. Their properties and wear resistance depend on carbides and on the nature of the matrix supporting these carbides. The paper presents test results of irons which contain (in wt.% 18-22 Cr and 2-5 C, and is alloyed by 1.7 Mo + 5 Ni + 2 Mn to improve the toughness. Tests showed as-cast irons with mostly austenitic matrix achieved hardness 36-53 HRC but their relative abrasion-resistance was higher than the tool steel STN 19436 heat treated on hardness 60 HRC.

Research on operation mode of abrasive grain during grinding

Science.gov (United States)

Ivanova, T. N.; Dement’ev, V. B.; Nikitina, O. V.

2018-03-01

The processing of materials by cutting with an abrasive tool is carried out by means of thousands of grains bonded together as a single whole. The quality of the abrasive tool is defined by cutting properties of abrasive grains and depends on features of spreading the temperature field in time and in the abrasive grain volume. Grains are exposed to heating and cooling during work. It leads to undesired effects such as a decrease of durability of grain retention in the binder, hardness, intensification of diffusion and oxidation processes between the binder and the grain, the occurrence of considerable temperature stresses in the grain itself. The obtained equation which allows calculation of temperature field of grain for one rotation of grinding wheel shows that the temperature of the wheel depends on grinding modes and thermophysical properties of abrasive material. Thus, as the time of contact of grain with processed material increases, the temperature in the cutting area rises. As thermophysical properties increase, the temperature in cutting area decreases. Thermal working conditions are determined to be different from each other depending on contact time of the grain and the material. For example, in case of creep-feed grinding, the peak value of temperature is higher than during multistep grinding; the depth of expansion is greater. While the speed of the thermal process in creep-feed grinding is 2-3 times lower than in multistep grinding, the gradient reduces 3-4 times. The analysis of machining methods shows that creep-feed grinding ensures greater depth of grain heating, a smaller heating rate and a reduced velocity gradient. It causes a decrease of probable allotropic modifications and prevents from occurring of heat strokes - cracking of grains due to high temperature falls. Consequently, it is necessary to employ creep-feed grinding to increase the efficiency of abrasive tool employing. Three operation modes of grinding wheel including blunting, full

A study on the abundance of quartz in thermal coals of India and its relation to abrasion index: Development of predictive model for abrasion

Energy Technology Data Exchange (ETDEWEB)

Bandopadhyay, A.K. [Central Institute of Mining and Fuel Research Digwadih Campus, P.O.-FRI, Dhanbad-828108, Jharkhand (India)

2010-10-01

The quartz content of each of the 61 thermal coals used in power stations in India has been determined using Fourier Transform Infra-Red (FTIR) Spectroscopy. It has been observed that quartz is abundant in the thermal coals and its proportion varies from 5 to 20% by wt. The abrasion index (AI), a measure of abrasion caused by coals, has been determined for each coal according to the procedure laid down in Indian Standard IS: 9949-1986. The data generated on abrasion together with ash and quartz percentages of the coals studied have been subjected to regression and correlation analysis. Positive correlations have been found between AI and quartz content and between AI and ash yield, but the correlation between AI and ash (A) and quartz (Q) percentages has been observed to be the most significant (R{sup 2} = 0.86). The linear regression model AI = 1.00A + 1.35Q thus developed has the ability to predict AI of the thermal coals within {+-} 10 mg/kg at 95.5% confidence level. Results of application of the model to predicting abrasion of a limited number of foreign coals with different origins have been found to be encouraging. Integration of other variables like the size and the shape of the abrading particles along with other physical properties of coal, like the bulk density and the grindability, with the model, in addition to the variables already considered, has been suggested for improved prediction. (author)

Hydration of poly( N-isopropylacrylamide) brushes on micro-silica beads measured by a fluorescent probe

Science.gov (United States)

Hattori, Yusuke; Nagase, Kenichi; Kobayashi, Jun; Kikuchi, Akihiko; Akiyama, Yoshikatsu; Kanazawa, Hideko; Okano, Teruo

2010-05-01

Hydration of poly( N-isopropylacrylamide) brushes on silica micro-beads was investigated using a fluorescent probe method. The free ends, the bottom, and the random of brushes were labeled with dansyl group. The emission spectra at the thin brushes were reduced with increasing temperature regardless of their labeling locations. At the free ends of thick brushes, the emission intensity was enhanced at 500 nm and reduced at 455 nm by heating, which was corresponding to the local micro-environmental change around the free ends. The spectral shift was speculated to be due to the enhancement of the flexibility and the hydration of thick brushes.

Analysis of carbon fiber brush loading in anodes on startup and performance of microbial fuel cells

KAUST Repository

Hutchinson, Adam J.

2011-11-01

Flat carbon anodes placed near a cathode in a microbial fuel cell (MFC) are adversely affected by oxygen crossover, but graphite fiber brush anodes placed near the cathode produce high power densities. The impact of the brush size and electrode spacing was examined by varying the distance of the brush end from the cathode and solution conductivity in multiple MFCs. The startup time was increased from 8 ± 1 days with full brushes (all buffer concentrations) to 13 days (50 mM), 14 days (25 mM) and 21 days (8 mM) when 75% of the brush anode was removed. When MFCs were all first acclimated with a full brush, up to 65% of the brush material could be removed without appreciably altering maximum power. Electrochemical impedance spectroscopy (EIS) showed that the main source of internal resistance (IR) was diffusion resistance, which together with solution resistance reached 100 Ω. The IR using EIS compared well with that obtained using the polarization data slope method, indicating no major components of IR were missed. These results show that using full brush anodes avoids adverse effects of oxygen crossover during startup, although brushes are much larger than needed to sustain high power. © 2011 Elsevier B.V.

Analysis of carbon fiber brush loading in anodes on startup and performance of microbial fuel cells

KAUST Repository

Hutchinson, Adam J.; Tokash, Justin C.; Logan, Bruce E.

2011-01-01

Flat carbon anodes placed near a cathode in a microbial fuel cell (MFC) are adversely affected by oxygen crossover, but graphite fiber brush anodes placed near the cathode produce high power densities. The impact of the brush size and electrode spacing was examined by varying the distance of the brush end from the cathode and solution conductivity in multiple MFCs. The startup time was increased from 8 ± 1 days with full brushes (all buffer concentrations) to 13 days (50 mM), 14 days (25 mM) and 21 days (8 mM) when 75% of the brush anode was removed. When MFCs were all first acclimated with a full brush, up to 65% of the brush material could be removed without appreciably altering maximum power. Electrochemical impedance spectroscopy (EIS) showed that the main source of internal resistance (IR) was diffusion resistance, which together with solution resistance reached 100 Ω. The IR using EIS compared well with that obtained using the polarization data slope method, indicating no major components of IR were missed. These results show that using full brush anodes avoids adverse effects of oxygen crossover during startup, although brushes are much larger than needed to sustain high power. © 2011 Elsevier B.V.

The use of non-bronchoscopic brushings to study the paediatric airway

Directory of Open Access Journals (Sweden)

Kicic Anthony

2005-06-01

Full Text Available Abstract Background The use of cytology brushes for the purpose of obtaining respiratory cells from adults for clinical and research purposes is well established. However, the safety and utility of non-bronchoscopic brushings to study the paediatric airway has not been assessed. The purpose of this study was to assess the practicality of using non-bronchoscopic brushing to sample epithelial cells from children for investigation of epithelial function in health and disease using a wide range of molecular and cellular techniques. Methods Non-bronchoscopic brushing was investigated in a non-selected cohort of healthy, and mildly asthmatic children presenting for surgery unrelated to respiratory conditions, at the major children's hospital in Perth. Safety and side-effects of the procedure were assessed. Cell number, phenotype and viability were measured for all samples. The potential of these cells for use in long-term cell culture, immunohistochemistry, western blotting, quantitative PCR and gene arraying was examined. Results Non-bronchoscopic brushing was well tolerated in all children. The only significant side effect following the procedure was cough: nursing staff reported cough in 20% of patients; parents reported cough in 40% of patients. Cells sampled were of sufficient quantity and quality to allow cell culture in 93% of samples. Similarly, protein and RNA extracted from the cells was suitable for investigation of both gene and protein expression using micro-array and real-time PCR. Conclusion Non-bronchoscopic brushing in children is safe and easy to perform, and is not associated with any complications. Using this technique, adequate numbers of epithelial cells can be retrieved to allow cell culture, western blotting, real time PCR, and microarray analysis. The purpose of this study is to demonstrate the utility of non-bronchoscopic airway brushing to obtain and study epithelial cells and to encourage others so that we can accelerate

Measurement of Tooth Brushing Frequency, Time of Day and Duration of Adults and Children in Jakarta, Indonesia

Directory of Open Access Journals (Sweden)

Anton Rahardjo

2015-05-01

Full Text Available Epidemiological study of tooth brushing is essential to evaluate dental health of a country. Objective: To obtain data on tooth brushing frequency, time of day and duration from adults and children in Jakarta, Indonesia. Methods: Toothbrushes containing data loggers were distributed to 120 random families in Jakarta to record how many times a day, when and for how long subjects brushed their teeth. The families were each composed of a mother, father and two children aged between 6 and 15 years. Results: The mean brushing frequency of the population was 1.27 times per day. The majority of the tooth brushing (46% was performed in the morning. The mean tooth brushing duration of this population was 57.29 seconds. The mothers’ tooth brushing frequencies tended to be higher than that of the other family members, and the fathers tended to brush their teeth longer. Conclusion: Effective education aimed at increasing both the duration and frequency of tooth brushing from once to twice per day is urgently required in Indonesia.DOI: 10.14693/jdi.v21i3.251

Prepolishing on a CNC platform with bound abrasive contour tools

Science.gov (United States)

Schoeffler, Adrienne E.; Gregg, Leslie L.; Schoen, John M.; Fess, Edward M.; Hakiel, Michael; Jacobs, Stephen D.

2003-05-01

Deterministic microgrinding (DMG) of optical glasses and ceramics is the commercial manufacturing process of choice to shape glass surfaces prior to final finishing. This process employs rigid bound matrix diamond tooling resulting in surface roughness values of 3-5μm peak to valley and 100-400nm rms, as well as mid-spatial frequency tool marks that require subsequent removal in secondary finishing steps. The ability to pre-polish optical surfaces within the grinding platform would reduce final finishing process times. Bound abrasive contour wheels containing cerium oxide, alumina or zirconia abrasives were constructed with an epoxy matrix. The effects of abrasive type, composition, and erosion promoters were examined for tool hardness (Shore D), and tested with commercial optical glasses in an Optipro CNC grinding platform. Metrology protocols were developed to examine tool wear and subsequent surface roughness. Work is directed to demonstrating effective material removal, improved surface roughness and cutter mark removal.

Development of abrasion resistant glass-ceramics from industrial waste products. Final report

Energy Technology Data Exchange (ETDEWEB)

von Roode, M.

1983-05-26

Slag-ceramics were produced from glass compositions using pelletized slag as the major ingredient. The abrasion resistance, fracture toughness and microstructure of the prepared glass and glass-ceramics were evaluated. Glas-ceramics with good abrasion resistance were obtained when iron oxide in conjunction with carbon was used as a nucleating agent. 5 figs., 11 tabs.

Efeito dose-resposta de uma formulação de dentifrício com concentração reduzida de fluoreto: estudo in vitro Dose-response effect of a dentifrice formulation with low fluoride concentration: an in vitro study

Directory of Open Access Journals (Sweden)

Helena Maria Decico Negri

2002-12-01

Full Text Available O desenvolvimento de dentifrício com menor concentração de flúor, visando crianças menores de 6 anos, tem sido sugerido para diminuir o risco de fluorose dental. Para que um dentifrício tenha potencial anticárie é necessário que ele forme no esmalte dental flúor fracamente ligado tipo fluoreto de cálcio (CaF2, o qual é considerado o responsável pelo efeito do flúor tópico. Considerando que a formação de CaF2 é função inversa do pH, foram formulados dentifrícios com pH 5,5. Foram preparados dentifrícios com 275, 550 e 1.100 ppm , contendo NaF/sílica, para verificar efeito dose-resposta os quais foram comparados com um placebo e o dentifrício Crest® (controle positivo - padrão. A biodisponibilidade dos dentifrícios, em termos de formação de flúor total (FT, CaF2 e fluorapatita (FA no esmalte dental humano foi avaliada. Para as dosagens de íon flúor foi utilizado eletrodo específico. Os resultados mostraram que a formulação com 550 ppm de foi mais eficiente que o placebo e aquela com 275 ppm em termos de formação de CaF2 (p 0,05. Uma relação dose-efeito foi observada em termos de CaF2 formado. Os resultados sugerem que a formulação modificada contendo 550 ppm de pode ser considerada equivalente ao dentifrício padrão com 1.100 ppm, a qual seria mais segura em termos de fluorose dental.The utilization of dentifrices with low fluorine concentration, for children under 6 years of age, has been suggested to reduce the risks of dental fluorosis. However, in order to have anticariogenic potential, the dentifrice should form loosely-bound fluorine (CaF2 on dental enamel. Considering that the formation of CaF2 is a function inversely related to pH, dentifrices with pH 5.5, with 275, 550 and 1,100 ppm (NaF/silica were developed in order to assess dose-response effects. A comparison between those dentifrices, a placebo product and the Crest toothpaste (positive control - standard was carried out. Furthermore, the

Characterization of abrasion-induced nanoparticle release from paints into liquids and air

Science.gov (United States)

Golanski, L.; Gaborieau, A.; Guiot, A.; Uzu, G.; Chatenet, J.; Tardif, F.

2011-07-01

Two standard methods for the characterization of the abrasion nanoparticle release into air and liquid from coatings containing nanoparticles were developed. Details of the abrasion processes and the measurement methods are shown. Paints were formulated in an industrial facility. Standard abrasion conditions in wet environments were simulated. The size distribution of the particles abraded into liquid was analyzed by a laser granulometer: submicrometric and micrometric particles were observed, but no nanometric particles. The nanoparticles released in liquid were deposited on filters for SEM (Scanning Electron Microscopy) analysis. No free or agglomerated nanoparticles were observed by SEM: nanoparticles seem to remain embedded in the paint matrix. The same coatings were abraded in the air using another standard method. The ELPI (Electrical Low Pressure Impactor) was used to determine the number size distribution of the dust generated. Abrasion is found to produce submicrometric and micrometric particles in the air but no nanoparticles. Further characterizations by SEM confirmed that no free or agglomerated nanoparticles were emitted: nanoparticles seem to remain embedded in the paint matrix.

Characterization of abrasion-induced nanoparticle release from paints into liquids and air

International Nuclear Information System (INIS)

Golanski, L; Guiot, A; Uzu, G; Tardif, F; Gaborieau, A; Chatenet, J

2011-01-01

Two standard methods for the characterization of the abrasion nanoparticle release into air and liquid from coatings containing nanoparticles were developed. Details of the abrasion processes and the measurement methods are shown. Paints were formulated in an industrial facility. Standard abrasion conditions in wet environments were simulated. The size distribution of the particles abraded into liquid was analyzed by a laser granulometer: submicrometric and micrometric particles were observed, but no nanometric particles. The nanoparticles released in liquid were deposited on filters for SEM (Scanning Electron Microscopy) analysis. No free or agglomerated nanoparticles were observed by SEM: nanoparticles seem to remain embedded in the paint matrix. The same coatings were abraded in the air using another standard method. The ELPI (Electrical Low Pressure Impactor) was used to determine the number size distribution of the dust generated. Abrasion is found to produce submicrometric and micrometric particles in the air but no nanoparticles. Further characterizations by SEM confirmed that no free or agglomerated nanoparticles were emitted: nanoparticles seem to remain embedded in the paint matrix.

Frequency of daily tooth brushing: predictors of change in 9- to 11-year old US children.

Science.gov (United States)

Polk, D E; Geng, M; Levy, S; Koerber, A; Flay, B R

2014-09-01

To investigate whether an increase in daily tooth brushing frequency in children was predicted by either a) having a strong intention to brush twice a day or b) their parents receiving information about their new caries experience. Secondary data analyses were conducted on two waves of data from the Aban Aya Youth Project and the Iowa Fluoride Study. The Aban Aya study included 576 10- and 11-year olds from Chicago, Illinois. The Iowa Fluoride Study included a convenience sample of 709 babies born in Iowa. The present study includes those children at age 9. In both studies, reported daily tooth brushing frequency was assessed twice six months apart. In the Aban Aya data, compared with children with a weak intention at wave 1 to brush twice a day, children with a strong intention to brush twice a day were more likely to increase their brushing frequency by wave 2, OR 7.0, 95%CI 1.5,32.9. In the Iowa Fluoride Study, compared with children who did not have new caries at wave 1, children who had new caries experience were less likely to increase their brushing frequency by wave 2, OR 0.4, 95%CI 0.2,0.9. Strengthening intention to brush twice a day might increase children's brushing frequency. However, simply providing parents with information about new caries probably will not. Future studies should assess tooth brushing frequency, habit strength, intention, and situational cues at closely-spaced waves.

Features of Running Brush Motors in Dry Nitrogen Environment When Using in Electrohydraulic Actuators

Directory of Open Access Journals (Sweden)

Y. A. Petrov

2014-01-01

Full Text Available The work concerns the constructive characteristics optimization of brushless D.C. (direct current motors used in electromechanical spacecraft drives.The spacecraft electromechanical drives and units use rather widely the brushless D.C. motors in which a motor commutator is replaced with more reliable semiconductor commutator controlled by the rotor position sensors. However, these motors are of low power.Electrohydraulic actuators (EHA use simple permanent-magnet motors (PMM of rather high power and commutator motors with graphite brush variable contacts.High reliability of brush motors, and, therefore a reliability of EHA in general, substantially depends on the quality of motor commutator operation. There are different reasons for a possible impact on the normal motor commutator operation. One of them is brush wear. Sparking brushes and burning commutator bars are possible in case brushes are poorly grinded to fit, brushes cannot freely move true in the brush holder box, and in case an incorrect force to clamp brushes to the commutator is chosen.It is established that drive wear resistance and operability depends on the gas environment composition being under sealed motor housing. In dry nitrogen environment brush wear suddenly raises because of the changing tribological performances of the commutator thus leading to essentially falling isolation resistance and no motor start.It is recommended to fill a space under sealed motor housing with air. Positive experience of operating spacecraft device containers with mobile electromechanical couples allowed us to find that in this case a dew point of filled air must be minus 20˚C.The paper offers an electromechanical alternative of design to the electrohydraulic actuators, with a ball-screw gear of the actuation mechanism, possessing a number of advantages.

Development of a novel bioactive glass for air-abrasion to selectively remove orthodontic adhesives.

Science.gov (United States)

Taha, Ayam A; Hill, Robert G; Fleming, Padhraig S; Patel, Mangala P

2018-05-01

To develop a novel, bioactive glass for removing residual orthodontic adhesive via air-abrasion, following bracket debonding, and to evaluate its effectiveness against a proprietary bioactive glass 45S5(Sylc™)-air-abrasion, and a slow-speed tungsten carbide (TC) bur. Three glasses were prepared and their bioactivity was proved. One novel glass (QMAT3) was selected due to its appropriate hardness, lower than that of enamel/45S5(Sylc™). Sixty extracted human premolars were randomly assigned to adhesive removal using: (a) QMAT3-air-abrasion, (b) 45S5(Sylc™)-air-abrasion, and (c) TC bur, which were further subdivided (n = 10) based on the adhesive used (Transbond XT™ or Fuji Ortho LC™). Enamel roughness was assessed using scanning electron microscopy (SEM) and non-contact profilometry before bracket bonding, after removing residual adhesive following bracket debonding and after polishing. QMAT3 formed apatite faster (6 h) than 45S5(Sylc™) (24 h) in Tris solution. QMAT3-air-abrasion gave the lowest enamel roughness (Ra) after removing the adhesives. SEM images showed a pitted, roughened enamel surface in the TC bur group and to a lesser extent with 45S5(Sylc™), while a virtually smooth surface without any damage was observed in the QMAT3-air-abrasion group. The time taken for adhesive removal with QMAT3 was comparable to 45S5(Sylc™) but was twice as long with the TC bur. QMAT3-air-abrasion is a promising technique for selective removal of adhesives without inducing tangible enamel damage. A novel bioactive glass has been developed as an alternative to the use of TC burs for orthodontic adhesive removal.

Metastatic urachal carcinoma in bronchial brush cytology

Directory of Open Access Journals (Sweden)

Fatima Zahra Aly

2013-01-01

Full Text Available Urachal carcinoma is rare comprising less than 1% of all bladder carcinomas. Metastases of urachal carcinoma have been reported to meninges, brain, ovary, lung, and maxilla. Cytologic features of metastatic urachal carcinoma have not been previously reported. We present a case of metastatic urachal adenocarcinoma in bronchial brushings and review the use of immunohistochemistry in its diagnosis. A 47-year-old female was seen initially in 2007 with adenocarcinoma of the bladder dome for which she underwent partial cystectomy. She presented in 2011 with a left lung mass and mediastinal adenopathy. Bronchoscopy showed an endobronchial lesion from which brushings were obtained. These showed numerous groups of columnar cells with medium sized nuclei and abundant cytoplasm. The cells were positive for CK20 and CDX2 and negative for CK7. The cytomorphological findings were similar to those in the previous resection specimen and concurrent biopsy. This is the first case report of bronchial brushings containing metastatic urachal carcinoma. No specific immunohistochemical profile is available for its diagnosis. The consideration of a second primary was a distinct possibility in this case due to the lapse of time from primary resection, absence of local disease, and lack of regional metastases.

A hybrid floating brush seal (HFBS) for improved sealing and wear performance in turbomachinery applications

Science.gov (United States)

Lattime, Scott Byran

A conceptually new type of seal has been developed for gas turbine applications which dramatically reduces wear and leakage associated with current labyrinth and brush seal technologies. The Hybrid Floating Brush Seal (HFBS) combines brush seal and film riding face seal technologies to create a hybrid seal that allows both axial and radial excursions of the sealed shaft, while simultaneously eliminating interface surface speeds (friction and heat) between the rotor and the brush material that characterize standard brush seal technology. A simple test rig was designed to evaluate feasibility of the HFBS under relatively low pressures and rotational speeds (50psig, 5krpm). A second test stand was created to study the effects of centrifugal force on bristle deflection. A third test facility was constructed for prototype development and extensive room temperature testing at moderate pressures and fairly high rotational speeds (100psig, 40krpm). This test rig also allowed the evaluation of the HFBS during axial movement of a rotating shaft. An analytical model to predict the effects of centrifugal force on the bristles of a rotating brush seal was developed. Room temperature analysis of the HFBS proved successful for relatively high operating rotational velocities at moderate pressures with very acceptable leakage rates for gas turbine engines. Brush seals were able to track rotor speeds up to 24krpm while maintaining sealing integrity. The HFBS's ability to function under axial shaft displacement and synchronous dynamic radial loading was also proven successful. Hydrodynamic performance of the face seal was proven to provide adequate stiffness and load carrying capacity to keep the brush seal from contacting the face seal at pressure drops across the brush of up to 100psi. Leakage performance over standard brush seal and labyrinth technology was quite dramatic. The HFBS showed its sealing advantage using much higher radial interference between the rotor and the bristle

Abrasion Testing of Critical Components of Hydrokinetic Devices

Energy Technology Data Exchange (ETDEWEB)

Worthington, Monty [ORPC Alaska; Ali, Muhammad [Ohio University; Ravens, Tom [University of Alaska Anchorage

2013-12-06

The objective of the Abrasion Testing of Critical Components of Hydrokinetic Devices (Project) was to test critical components of hydrokinetic devices in waters with high levels of suspended sediment – information that is widely applicable to the hydrokinetic industry. Tidal and river sites in Alaska typically have high suspended sediment concentrations. High suspended sediment also occurs in major rivers and estuaries throughout the world and throughout high latitude locations where glacial inputs introduce silt into water bodies. In assessing the vulnerability of technology components to sediment induced abrasion, one of the greatest concerns is the impact that the sediment may have on device components such as bearings and seals, failures of which could lead to both efficiency loss and catastrophic system failures.

Making strong polyelectrolyte brushes pH-sensitive by incorporation of gold nanoparticles.

Science.gov (United States)

Boyaciyan, D; Krause, P; von Klitzing, R

2018-04-19

Doping polymer brushes with gold nanoparticles (AuNPs) results in composite materials with colorimetric sensor properties. The present paper addresses the effect of electrostatic particle-particle interaction and the effect of the polymer brush type on particle assembly formation within the polymer matrix. The prospect for long-term use as colorimetric sensors is tested. Therefore, two different types of brushes of pH-insensitive polymers, non-ionic poly(N-isopropylacrylamide) (PNIPAM) and cationic poly-[2-(methacryloyloxy)ethyl] trimethylammonium chloride (PMETAC), are studied. After incubation of the non-ionic PNIPAM brush in an aqueous suspension of AuNPs with a pH-sensitive carboxylic acid capping, hydrogen binding led to attachment of the AuNPs, but they were easily detached at high pH due to loss of the hydrogen binding. In contrast, the anionic AuNPs adhere well to cationic PMETAC brushes even after post-treatment at low pH where the charge density of the AuNPs is strongly reduced. Therefore, the PMETAC/AuNP composites were further tested with respect to their stability against pH variations and their impact for colorimetric sensors. Although the neat PMETAC brush is not pH-sensitive, after embedding pH-sensitive AuNPs, the PMETAC/AuNP composite becomes pH-sensitive in a reversible manner. This is detectable by the reversible shift of the plasmon band and the reversible thickness change of the composites by exposing them to different pH.

Polymer Brush-Functionalized Chitosan Hydrogels as Antifouling Implant Coatings.

Science.gov (United States)

Buzzacchera, Irene; Vorobii, Mariia; Kostina, Nina Yu; de Los Santos Pereira, Andres; Riedel, Tomáš; Bruns, Michael; Ogieglo, Wojciech; Möller, Martin; Wilson, Christopher J; Rodriguez-Emmenegger, Cesar

2017-06-12

Implantable sensor devices require coatings that efficiently interface with the tissue environment to mediate biochemical analysis. In this regard, bioinspired polymer hydrogels offer an attractive and abundant source of coating materials. However, upon implantation these materials generally elicit inflammation and the foreign body reaction as a consequence of protein fouling on their surface and concomitant poor hemocompatibility. In this report we investigate a strategy to endow chitosan hydrogel coatings with antifouling properties by the grafting of polymer brushes in a "grafting-from" approach. Chitosan coatings were functionalized with polymer brushes of oligo(ethylene glycol) methyl ether methacrylate and 2-hydroxyethyl methacrylate using photoinduced single electron transfer living radical polymerization and the surfaces were thoroughly characterized by XPS, AFM, water contact angle goniometry, and in situ ellipsometry. The antifouling properties of these new bioinspired hydrogel-brush coatings were investigated by surface plasmon resonance. The influence of the modifications to the chitosan on hemocompatibility was assessed by contacting the surfaces with platelets and leukocytes. The coatings were hydrophilic and reached a thickness of up to 180 nm within 30 min of polymerization. The functionalization of the surface with polymer brushes significantly reduced the protein fouling and eliminated platelet activation and leukocyte adhesion. This methodology offers a facile route to functionalizing implantable sensor systems with antifouling coatings that improve hemocompatibility and pave the way for enhanced device integration in tissue.

The synthesis of hydrogels with controlled distribution of polymer brushes in hydrogel network

Energy Technology Data Exchange (ETDEWEB)

Sun, YuWei; Zhou, Chao; Zhang, AoKai; Xu, LiQun; Yao, Fang [School of Chemistry and Chemical Engineering, Southeast University, Jiangning District, Nanjing, Jiangsu Province, 211189 (China); Cen, Lian, E-mail: cenlian@hotmail.com [National Tissue Engineering Center of China, No.68, East Jiang Chuan Road, Shanghai, 200241 (China); School of Chemical Engineering, East China University of Science and Technology, No.130, Mei Long Road, Shanghai, 200237 (China); Fu, Guo-Dong, E-mail: fu7352@seu.edu.cn [School of Chemistry and Chemical Engineering, Southeast University, Jiangning District, Nanjing, Jiangsu Province, 211189 (China)

2014-11-30

Highlights: • Many biological tissues are 3-dimensionally asymmetric in structure and properties, it would be desirable if hydrogels could bear such structural similarity with specialized surface and bulk properties. Moreover, gradual but continuous variation in spatial structural and property is also a common phenomenon in biological tissues, such as interfaces between bone and tendon, or between bone and cartilage. Hence, the development of a method to introduce well-defined functional polymer brushes on PEG hydrogels, especially with precisely controlled spatial structure in 3-dimensions, would impart the hydrogels with special functionalities and wider applications. Poly(ethylene glycol) (PEG) hydrogels with 3-dimensionally controlled well-defined poly(N-isopropylacrylamide) (poly(NIPAAm)) brushes were prepared by combined copper(I)-catalyzed azide-alkyne cycloaddition (“Click Chemistry”) and atom transfer radical polymerization (ATRP). The resulting hydrogels were presented as representatives with their detailed synthesis routes and characterization. H{sub PEG}-S-poly(NIPAAm) is a hydrogel with poly(NIPAAm) brushes mainly grafted on surface, whereas H{sub PEG}-G-poly(NIPAAm) has a gradiently decreased poly(NIPAAm) brushes in their chain length from surface to inside. On the other hand, poly(NIPAAm) brushes in H{sub PEG}-U-poly(NIPAAm) are uniformly dispersed throughout the whole hydrogel network. Successful preparation of H{sub PEG}-S-poly(NIPAAm), H{sub PEG}-G-poly(NIPAAm) and H{sub PEG}-U-poly(NIPAAm) were ascertained by X-ray photoelectron spectroscopy (XPS) and water contact angle measurement. Hence, the flexibility and controllability of the synthetic strategy in varying the distribution of polymer brushes and hydrogel surface properties was demonstrated. Hydrogels with tunable and well-defined 3-dimensional poly(NIPAAm) polymer brushes could be tailor-designed to find potential applications in smart devices or skin dressing, such as for diabetics

Peptides Displayed as High Density Brush Polymers Resist Proteolysis and Retain Bioactivity

Science.gov (United States)

2015-01-01

We describe a strategy for rendering peptides resistant to proteolysis by formulating them as high-density brush polymers. The utility of this approach is demonstrated by polymerizing well-established cell-penetrating peptides (CPPs) and showing that the resulting polymers are not only resistant to proteolysis but also maintain their ability to enter cells. The scope of this design concept is explored by studying the proteolytic resistance of brush polymers composed of peptides that are substrates for either thrombin or a metalloprotease. Finally, we demonstrate that the proteolytic susceptibility of peptide brush polymers can be tuned by adjusting the density of the polymer brush and offer in silico models to rationalize this finding. We contend that this strategy offers a plausible method of preparing peptides for in vivo use, where rapid digestion by proteases has traditionally restricted their utility. PMID:25314576

Finishing of display glass for mobile electronics using 3M Trizact diamond tile abrasive pads

Science.gov (United States)

Zheng, Lianbin; Fletcher, Tim; Na, Tee Koon; Sventek, Bruce; Romero, Vince; Lugg, Paul S.; Kim, Don

2010-10-01

This paper will describe a new method being used during the finishing of glass displays for mobile electronics including mobile hand held devices and notebook computers. The new method consists of using 3M TrizactTM Diamond Tile Abrasive Pads. TrizactTM Diamond Tile is a structured fixed abrasive grinding technology developed by 3M Company. The TrizactTM Diamond Tile structured abrasive pad consists of an organic (polymeric binder) - inorganic (abrasive mineral, i.e., diamond) composite that is used with a water-based coolant. TrizactTM Diamond Tile technology can be applied in both double and single side grinding applications. A unique advantage of TrizactTM Diamond Tile technology is the combination of high stock removal and low sub-surface damage. Grinding results will be presented for both 9 micron and 20 micron grades of TrizactTM Diamond Tile abrasive pads used to finish several common display glasses including Corning GorillaTM glass and Soda Lime glass.

Cryogenically assisted abrasive jet micromachining of polymers

International Nuclear Information System (INIS)

Getu, H; Papini, M; Spelt, J K

2008-01-01

The abrasive jet micromachining (AJM) of elastomers and polymers such as polydimethylsiloxane (PDMS), acrylonitrile butadiene styrene (ABS) and polytetrafluoroethylene (PTFE) for use in micro-fluidic devices was found to be very slow or impossible at room temperature. To enhance the material removal rate in such materials, a stream of liquid nitrogen (LN 2 ) was injected into the abrasive jet, cooling the target to cryogenic temperatures. Erosion rate measurements on the three polymeric materials (PDMS, ABS and PTFE) with and without the use of LN 2 were compared along with the profiles of micromachined channels and holes. It was found that the use of LN 2 cooling caused brittle erosion in PDMS, allowing it to be micromachined successfully. An erosion rate increase was also observed in PTFE and ABS at high and intermediate impact angles. The use of LN 2 also was found to reduce particle embedding

Protective Effect of Adhesive Systems associated with Neodymium-doped Yttrium Aluminum Garnet Laser on Enamel Erosive/Abrasive Wear.

Science.gov (United States)

Crastechini, Erica; Borges, Alessandra B; Becker, Klaus; Attin, Thomas; Torres, Carlos Rg

2017-10-01

This study evaluated the efficacy of self-etching adhesive systems associated or not associated with the neodymium-doped yttrium aluminum garnet (Nd:YAG) laser on the protection against enamel erosive/abrasive wear. Bovine enamel specimens were demineralized with 0.3% citric acid (5 minutes). The samples were randomly assigned to eight groups (n = 20): SB - Single Bond Universal (3M/ESPE); SB+L - Single Bond Universal + laser (80 mJ/10 Hz); FB - Futurabond U (Voco); FB+L -Futurabond U + laser; GEN - G-aenial bond (GC); GEN+L -G-aenial bond + laser; L - laser irradiation; and C - no treatment. The laser was applied before light curing. The samples were subjected to erosive/abrasive challenges (0.3% citric acid - 2 minutes and tooth brushing four times daily for 5 days). Enamel surface loss was recovered profilometrically by comparison of baseline and final profiles. The adhesive layer thickness, retention percentage of the protective layer, and microhardness of cured adhesive were measured. Data were analyzed using one-way analysis of variance and Tukey's test (5%). There were significant differences for all parameters (p = 0.0001). Mean values ± SD and results of the Tukey's test were: Surface wear: GEN - 4.88 (±1.09)a, L - 5.04 ± 0.99)a, FB - 5.32 (±0.93)ab, GEN + L - 5.46 (±1.27)abc, SB + L - 5.78 (±1.12)abc, FB + L - 6.23 (±1.25)bc, SB - 6.35 (±1.11)c, and C - 6.46 (±0.61)c; layer thickness: GEN - 15.2 (±8.63)c, FB - 5.06 (±1.96)a, GEN + L - 13.96 (±7.07)bc, SB + L - 4.24 (±2.68)a, FB + L - 9.03 (±13.02)abc, and SB - 7.49 (±2.80)ab; retention: GEN - 68.89 (±20.62)c, FB - 54.53 (±24.80)abc, GEN + L - 59.90 (±19.79)abc, SB + L - 63.37 (±19.30)bc, FB + L - 42.23 (±17.68) a, and SB - 47.78 (±18.29)ab; microhardness: GEN - 9.27 (±1.75)c; FB - 6.99 (±0.89)b; GEN + L - 6.22 (±0.87)ab; SB + L - 15.48 (±2.51)d; FB + L - 10.67 (±1.58)c; SB - 5.00 (±1.60)a. The application of Futurabond U and G-aenial bond on enamel surface, as well as the Nd

Spectroscopic study of a DNA brush synthesized in situ by surface initiated enzymatic polymerization.

Science.gov (United States)

Khan, M Nuruzzaman; Tjong, Vinalia; Chilkoti, Ashutosh; Zharnikov, Michael

2013-08-29

We used a combination of synchrotron-based X-ray photoelectron spectroscopy (XPS) and angle-resolved near-edge X-ray absorption fine structure (NEXAFS) spectroscopy to study the chemical integrity, purity, and possible internal alignment of single-strand (ss) adenine deoxynucleotide (poly(A)) DNA brushes. The brushes were synthesized by surface-initiated enzymatic polymerization (SIEP) on a 25-mer of adenine self-assembled monolayer (SAM) on gold (A25-SH), wherein the terminal 3'-OH of the A25-SH serve as the initiation sites for SIEP of poly(A). XPS and NEXAFS spectra of poly(A) brushes were found to be almost identical to those of A25-SH initiator, with no unambiguous traces of contamination. Apart from the well-defined chemical integrity and contamination-free character, the brushes were found to have a high degree of orientational order, with an upright orientation of individual strands, despite their large thickness up to ~55 nm, that corresponds to a chain length of at least several hundred nucleotides for individual ssDNA molecules. The orientational order exhibited by these poly(A) DNA brushes, mediated presumably by base stacking, was found to be independent of the brush thickness as long as the packing density was high enough. The well-defined character and orientational ordering of the ssDNA brushes make them a potentially promising system for different applications.

Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards

Science.gov (United States)

Street, Kenneth W., Jr.; Kobrick, Ryan L.; Klaus, David M.

2013-01-01

Abrasion of mechanical components and fabrics by soil on Earth is typically minimized by the effects of atmosphere and water. Potentially abrasive particles lose sharp and pointed geometrical features through erosion. In environments where such erosion does not exist, such as the vacuum of the Moon, particles retain sharp geometries associated with fracturing of their parent particles by micrometeorite impacts. The relationship between hardness of the abrasive and that of the material being abraded is well understood, such that the abrasive ability of a material can be estimated as a function of the ratio of the hardness of the two interacting materials. Knowing the abrasive nature of an environment (abrasive)/construction material is crucial to designing durable equipment for use in such surroundings. The objective of this work was to evaluate a set of standardized metrics proposed for characterizing a surface that has been scratched from a two-body abrasion test. This is achieved by defining a new abrasion region termed Zone of Interaction (ZOI). The ZOI describes the full surface profile of all peaks and valleys, rather than just measuring a scratch width. The ZOI has been found to be at least twice the size of a standard width measurement; in some cases, considerably greater, indicating that at least half of the disturbed surface area would be neglected without this insight. The ZOI is used to calculate a more robust data set of volume measurements that can be used to computationally reconstruct a resultant profile for de tailed analysis. Documenting additional changes to various surface roughness par ameters also allows key material attributes of importance to ultimate design applications to be quantified, such as depth of penetration and final abraded surface roughness. Further - more, by investigating the use of custom scratch tips for specific needs, the usefulness of having an abrasion metric that can measure the displaced volume in this standardized

Bio-active glass air-abrasion has the potential to remove resin composite restorative material selectively

International Nuclear Information System (INIS)

Milly, Hussam; Andiappan, Manoharan; Thompson, Ian; Banerjee, Avijit

2014-01-01

The aims of this study were to assess: (a) the chemistry, morphology and bioactivity of bio-active glass (BAG) air-abrasive powder, (b) the effect of three air-abrasion operating parameters: air pressure, powder flow rate (PFR) and the abrasive powder itself, on the selective removal of resin composite and (c) the required “time taken”. BAG abrasive particles were characterised using scanning electron microscopy-energy dispersive X-ray spectrometry (SEM-EDX) and Fourier-transform infrared spectroscopy (FTIR). Standardised resin composite restorations created within an enamel analogue block (Macor™) in vitro, were removed using air-abrasion undersimulated clinical conditions. 90 standardised cavities were scanned before and after resin composite removal using laser profilometry and the volume of the resulting 3D images calculated. Multilevel linear model was used to identify the significant factors affecting Macor™ removal. BAG powder removed resin composite more selectively than conventional air-abrasion alumina powder using the same operating parameters (p < 0.001) and the effect of altering the unit's operating parameters was significant (p < 0.001). In conclusion, BAG powder is more efficient than alumina in the selective removal of resin composite particularly under specific operating parameters, and therefore may be recommended clinically as a method of preserving sound enamel structure when repairing and removing defective resin composite restorations.

Robotic edge machining using elastic abrasive tool

Science.gov (United States)

Sidorova, A. V.; Semyonov, E. N.; Belomestnykh, A. S.

2018-03-01

The article describes a robotic center designed for automation of finishing operations, and analyzes technological aspects of an elastic abrasive tool applied for edge machining. Based on the experimental studies, practical recommendations on the application of the robotic center for finishing operations were developed.

Dynamic Mechanical Analysis and Three-Body Abrasive Wear Behaviour of Thermoplastic Copolyester Elastomer Composites

Directory of Open Access Journals (Sweden)

Hemanth Rajashekaraiah

2014-01-01

Full Text Available Various amounts of short fibers (glass and carbon and particulate fillers like polytetrafluoroethylene (PTFE, silicon carbide (SiC, and alumina (Al2O3 were systematically introduced into the thermoplastic copolyester elastomer (TCE matrix for reinforcement purpose. The mechanical properties such as storage modulus, loss modulus, and Tan δ by dynamic mechanical analysis (DMA and three-body abrasive wear performance on a dry sand rubber wheel abrasion tester have been investigated. For abrasive wear study, the experiments were planned according to L27 orthogonal array by considering three factors and three levels. The complex moduli for TCE hybrid composites were pushed to a higher level relative to the TCE filled PTFE composite. At lower temperatures (in the glassy region, the storage modulus increases with increase in wt.% of reinforcement (fiber + fillers and the value is maximum for the composite with 40 wt.% reinforcement. The loss modulus and damping peaks were also found to be higher by the incorporation of SiC and Al2O3 microfillers. The routine abrasive wear test results indicated that TCE filled PTFE composite exhibited better abrasion resistance. Improvements in the abrasion resistance, however, have not been achieved by short-fiber and particlaute filler reinforcements. From the Taguchi’s experimental findings, optimal combination of control factors were obtained for minimum wear volume and also predictive correlations were proposed. Further, the worn surface morphology of the samples was discussed.

The abrasive effect of commercial whitening toothpastes on eroded enamel.

Science.gov (United States)

Mosquim, Victor; Martines Souza, Beatriz; Foratori Junior, Gerson Aparecido; Wang, Linda; Magalhães, Ana Carolina

2017-06-01

To evaluate the in vitro abrasive effect of commercial whitening toothpastes on eroded bovine enamel samples in respect to erosive tooth wear. 72 bovine crowns were embedded, polished and subjected to the baseline profile analysis. The samples were then protected in 2/3 of the enamel surface and were randomly assigned to six groups (n= 12/group): G1: Oral-B 3D White, G2: Close-up Diamond Attraction Power White, G3: Sorriso Xtreme White 4D, G4: Colgate Luminous White, G5: Crest (conventional toothpaste), G6:erosion only (control). All samples were submitted to an erosive pH cycling (4 x 90 seconds in 0.1% citric acid, pH 2.5, per day) and abrasive challenges (2 x 15 seconds, per day) for 7 days. After the first and the last daily cycles, the samples were subjected to abrasive challenges, using a toothbrushing machine, soft toothbrushes and slurry of the tested toothpastes (1.5 N). Between the challenges, the samples were immersed in artificial saliva. The final profile was obtained and overlaid to the baseline profile for the calculation of the erosive tooth wear (μm). The data were subjected to Kruskal-Wallis/Dunn tests (Penamel wear (3.68±1.06 μm), similarly to G3 (3.17± 0.80 μm) and G4 (3.44± 1.29 μm). G3 and G4 performed similarly between them and compared with G5 (2.35± 1.44 μm). G2 (1.51± 0.95 μm) and G6 (0.85± 0.36 μm) showed the lowest enamel wear, which did not differ between them and from G5. Oral-B 3D White showed the highest abrasive potential while Close-up Diamond Attraction Power White showed the lowest abrasive potential on eroded enamel in vitro. This study showed that some commercial whitening toothpastes, especially those containing pyrophosphate associated with hydrated silica, enhanced enamel erosive wear.

Segment density profiles of polyelectrolyte brushes determined by Fourier transform ellipsometry

Science.gov (United States)

Biesalski, Markus; Rühe, Jürgen; Johannsmann, Diethelm

1999-10-01

We describe a method for the explicit determination of the segment density profile φ(z) of surface-attached polymer brushes with multiple angle of incidence null-ellipsometry. Because the refractive index contrast between the brush layer and the solvent is weak, multiple reflections are of minor influence and the ellipsometric spectrum is closely related to the Fourier transform of the refractive index profile, thereby allowing for explicit inversion of the ellipsometric data. We chose surface-attached monolayers of polymethacrylic acid (PMAA), a weak polyelectrolyte, as a model system and determined the segment density profile of this system as a function of the pH value of the surrounding medium by the Fourier method. Complementary to the Fourier analysis, fits with error functions are given as well. The brushes were prepared on the bases of high refractive index prisms with the "grafting-from" technique. In water, the brushes swell by more than a factor of 30. The swelling increases with increasing pH because of a growing fraction of dissociated acidic groups leading to a larger electrostatic repulsion.

Damage to the edge of steel stampings and abrasive during ultrasonic hydroabrasive machining

International Nuclear Information System (INIS)

Dokuchaeva, V.A.; Chernov, A.P.

1976-01-01

Principles have been established explaining the fracture of abrasive material in the process of ultrasonic hydroabrasive treatment, and a method is proposed suitable for the calculation of steel barb erosion in the hydroabrasive flux. It is assumed that fracture occurs along the entire edge surface and that the losses caused by plastic deformation are small. Conclusion has been made as to the governing the change of the abrasive particle size in the time of treatment. It is shown that the most serious fracture takes place at initial stage of the treatment, terminating practically after 60 minutes of operation. Curves showing the distribution of boron carbide abrasive particles are presented

Material Abrasive Water Jet Cutting Investigation by Means Accompanying Physical Phenomena

OpenAIRE

Kinik, D.; Gánovská, B.; Hloch, S. (Sergej); Cárach, J.; Lehocká, D.

2013-01-01

The paper deals with the indirect ways of on-line monitoring of technological processes of cutting. The objective of the study is a design of on-line monitoring system for the cutting technology through an abrasive water jet. In cutting by the abrasive water jet two parallel phenomena are formed. The phenomena are represented by generated surface and vibrations. For the purpose of proving of the hypothetical assumptions on dependence of generated surface quality on vibrations the ex...

Description of fuel element brush assembly's fabrication for 105-K west

International Nuclear Information System (INIS)

Maassen, D.P.

1997-01-01

This report is a description of the process to redesign and fabricate, as well as, describe the features of the Fuel Element Brush Assembly used in the 105-K West Basin. This narrative description will identify problems that occurred during the redesigning and fabrication of the 105-K West Basin Fuel Element Brush Assembly and specifically address their solutions

Structural analysis of paintings based on brush strokes

Science.gov (United States)

Sablatnig, Robert; Kammerer, Paul; Zolda, Ernestine

1998-05-01

The origin of works of art can often not be attributed to a certain artist. Likewise it is difficult to say whether paintings or drawings are originals or forgeries. In various fields of art new technical methods are used to examine the age, the state of preservation and the origin of the materials used. For the examination of paintings, radiological methods like X-ray and infra-red diagnosis, digital radiography, computer-tomography, etc. and color analyzes are employed to authenticate art. But all these methods do not relate certain characteristics in art work to a specific artist -- the artist's personal style. In order to study this personal style of a painter, experts in art history and image processing try to examine the 'structural signature' based on brush strokes within paintings, in particular in portrait miniatures. A computer-aided classification and recognition system for portrait miniatures is developed, which enables a semi- automatic classification and forgery detection based on content, color, and brush strokes. A hierarchically structured classification scheme is introduced which separates the classification into three different levels of information: color, shape of region, and structure of brush strokes.

Development of Self-Assembled Nanoscale Templates via Microphase Separation Induced by Polymer Brushes

Science.gov (United States)

Chu, Elza

Phase separation in soft matter has been the crucial element in generating hybrid materials, such as polymer blends and mixed polymer brushes. This dissertation discusses two methods of developing self-assembled nanoscale templates via microphase separation induced by polymer brush synthesis. This work introduces a novel soft substrate approach with renewable grafting sites where polyacrylamide is "grafted through" chitosan soft substrates. The mechanism of grafting leads to ordered arrays of filament-like nanostructures spanning the chitosan-air interface. Additionally, the chemical composition of the filaments allows for post-chemical modification to change the physical properties of the filaments, and subsequently tailor surfaces for specific application. Unlike traditional materials, multi-functional or "smart" materials, such as binary polymer brushes (BPB) are capable of spontaneously changing the spatial distribution of functional groups and morphology at the surface upon external stimuli. Although promising in principle, the limited range of available complementary polymers with common non-selective solvents confines the diversity of usable materials and restricts any further advancement in the field. This dissertation also covers the fabrication and characterization of responsive nanoscale polystyrene templates or "mosaic" brushes that are capable of changing interfacial composition upon exposure to varying solvent qualities. Using a "mosaic" brush template is a unique approach that allows the fabrication of strongly immiscible polymer BPB without the need for a common solvent. The synthesis of such BPB is exemplified by two strongly immiscible polymers, i.e. polystyrene (polar) and polyacrylamide (non-polar), where polyacrylamide brush is "graft through" a Si-substrate modified with the polystyrene collapsed "mosaic" brush. The surface exhibits solvent-triggered responses, as well as application potential for anti-biofouling.

A Nanosecond Pulsed Plasma Brush for Surface Decontamination

Science.gov (United States)

Neuber, Johanna; Malik, Muhammad; Song, Shutong; Jiang, Chunqi

2015-11-01

This work optimizes a non-thermal, atmospheric pressure plasma brush for surface decontamination. The generated plasma plumes with a maximum length of 2 cm are arranged in a 5 cm long, brush-like array. The plasma was generated in ambient air with Acinetobacter baumannii. Laminate surfaces inoculated with over-night cultured bacteria were subject to the plasma treatment for varying water concentrations in He, flow rates and discharge voltages. It was found that increasing the water content of the feed gas greatly enhanced the bactericidal effect. Emission spectroscopy was performed to identify the reactive plasma species that contribute to this variation. Additional affiliation: Frank Reidy Research Center for Bioelectrics

Chemical mechanical polishing of hard disk substrate with {alpha}-alumina-g-polystyrene sulfonic acid composite abrasive

Energy Technology Data Exchange (ETDEWEB)

Lei Hong, E-mail: hong_lei2005@yahoo.com.c [Research Center of Nano-science and Nano-technology, Shanghai University, Shanghai 200444 (China); Bu Naijing; Chen Ruling; Hao Ping [Research Center of Nano-science and Nano-technology, Shanghai University, Shanghai 200444 (China); Neng Sima; Tu Xifu; Yuen Kwok [Shenzhen Kaifa Magnetic Recording Co., LTD, Shenzhen, 518035 (China)

2010-05-03

{alpha}-Alumina-g-polystyrene sulfonic acid ({alpha}-Al{sub 2}O{sub 3}-g-PSS) composite abrasive was prepared by surface activation, graft polymerization and sulfonation, successively. The composition, dispersibility and morphology of the product were characterized by Fourier transformed infrared spectroscopy, laser particle size analysis and scanning electron microscopy, respectively. The chemical mechanical polishing (CMP) performances of the composite abrasive on hard disk substrate with nickel-phosphorous plating were investigated. The microscopy images of the polished surfaces show that {alpha}-Al{sub 2}O{sub 3}-g-PSS composite abrasive results in improved CMP and post-CMP cleaning performances than pure {alpha}-alumina abrasive under the same testing conditions.

Experimental Evidence that Abrasion of Carbonate Sand is a Significant Source of Carbonate Mud

Science.gov (United States)

Trower, L.; Kivrak, L.; Lamb, M. P.; Fischer, W. W.

2017-12-01

Carbonate mud is a major sedimentary component of modern and ancient tropical carbonate environments, yet its enigmatic origin remains debated. Early views on the origin of carbonate mud considered the abrasion of carbonate sand during sediment transport as a possible mechanism. In recent decades, however, prevailing thought has generally settled on a binary explanation: 1) precipitation of aragonite needles within the water column, and 2) post-mortem dispersal of biological aragonite, in particular from algae, and perhaps aided by fish. To test these different hypotheses, we designed a model and a set of laboratory experiments to quantify the rates of mud production associated with sediment transport. We adapted a recent model of ooid abrasion rate to predict the rate of mud production by abrasion of carbonate sand as a function of grain size and sediment transport mode. This model predicts large mud production rates, ranging from 103 to 104 g CaCO3/m2/yr for typical grain sizes and transport conditions. These rate estimates are at least one order of magnitude more rapid than the 102 g CaCO3/m2/yr estimates for other mechanisms like algal biomineralization, indicating that abrasion could produce much larger mud fluxes per area as other mechanisms. We tested these estimates using wet abrasion mill experiments; these experiments generated mud through mechanical abrasion of both ooid and skeletal carbonate sand for grain sizes ranging from 250 µm to >1000 µm over a range of sediment transport modes. Experiments were run in artificial seawater, including a series of controls demonstrating that no mud was produced via homogenous nucleation and precipitation in the absence of sand. Our experimental rates match the model predictions well, although we observed small systematic differences in rates between abrasion ooid sand and skeletal carbonate sand that likely stems from innate differences in grain angularity. Electron microscopy of the experimental products revealed

Liquid abrasive grit blasting literature search and decontamination scoping tests report

International Nuclear Information System (INIS)

Ferguson, R.L.

1993-10-01

Past decontamination and solvent recovery activities at the Idaho Chemical Processing Plant (ICPP) have resulted in the accumulation of 1.5 million gallons of radioactively contaminated sodium-bearing liquid waste. Future decontamination activities at the ICPP could result in the production of 5 million gallons or more of sodium-bearing waste using the current decontamination techniques of chemical/water flushes and steam jet cleaning. With the curtailment of reprocessing at the ICPP, the focus of decontamination is shifting from maintenance for continued operation of the facilities to decommissioning. As decommissioning plans are developed, new decontamination methods must be used which result in higher decontamination factors and generate lower amounts of sodium-bearing secondary waste. The primary initiative of the WINCO Decontamination Development Program is the development of methods to eliminate/minimize the use of sodium-bearing decontamination chemicals. One method that was chosen for cold scoping studies during FY-93 was abrasive grit blasting. Abrasive grit blasting has been used in many industries and a vast amount of research and development has already been conducted. However, new grits, process improvements and ICPP applicability was investigated. This evaluation report is a summary of the research efforts and scoping tests using the liquid abrasive grit blasting decontamination technique. The purpose of these scoping tests was to determine the effectiveness of three different abrasive grits: plastic beads, glass beads and alumina oxide

CFD Based Erosion Modelling of Abrasive Waterjet Nozzle using Discrete Phase Method

International Nuclear Information System (INIS)

Kamarudin, Naqib Hakim; Prasada Rao, A K; Azhari, Azmir

2016-01-01

In Abrasive Waterjet (AWJ) machining, the nozzle is the most critical component that influences the performance, precision and economy. Exposure to a high speed jet and abrasives makes it susceptible to wear erosion which requires for frequent replacement. The present works attempts to simulate the erosion of the nozzle wall using computational fluid dynamics. The erosion rate of the nozzle was simulated under different operating conditions. The simulation was carried out in several steps which is flow modelling, particle tracking and erosion rate calculation. Discrete Phase Method (DPM) and K-ε turbulence model was used for the simulation. Result shows that different operating conditions affect the erosion rate as well as the flow interaction of water, air and abrasives. The simulation results correlates well with past work. (paper)

Molecular dynamics simulations of polyelectrolyte brushes under poor solvent conditions: origins of bundle formation.

Science.gov (United States)

He, Gui-Li; Merlitz, Holger; Sommer, Jens-Uwe

2014-03-14

Molecular dynamics simulations are applied to investigate salt-free planar polyelectrolyte brushes under poor solvent conditions. Starting above the Θ-point with a homogeneous brush and then gradually reducing the temperature, the polymers initially display a lateral structure formation, forming vertical bundles of chains. A further reduction of the temperature (or solvent quality) leads to a vertical collapse of the brush. By varying the size and selectivity of the counterions, we show that lateral structure formation persists and therefore demonstrate that the entropy of counterions being the dominant factor for the formation of the bundle phase. By applying an external compression force on the brush we calculate the minimal work done on the polymer phase only and prove that the entropy gain of counterions in the bundle state, as compared to the homogeneously collapsed state at the same temperature, is responsible for the lateral microphase segregation. As a consequence, the observed lateral structure formation has to be regarded universal for osmotic polymer brushes below the Θ-point.

Bio-active glass air-abrasion has the potential to remove resin composite restorative material selectively

Energy Technology Data Exchange (ETDEWEB)

Milly, Hussam [Biomaterials, Biomimetics and Biophotonics Research Group, Kings College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom); Andiappan, Manoharan [Unit of Dental Public Health, Kings College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom); Thompson, Ian [Biomaterials, Biomimetics and Biophotonics Research Group, Kings College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom); Banerjee, Avijit, E-mail: avijit.banerjee@kcl.ac.uk [Biomaterials, Biomimetics and Biophotonics Research Group, Kings College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom); Unit of Conservative Dentistry, King' s College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom)

2014-06-01

The aims of this study were to assess: (a) the chemistry, morphology and bioactivity of bio-active glass (BAG) air-abrasive powder, (b) the effect of three air-abrasion operating parameters: air pressure, powder flow rate (PFR) and the abrasive powder itself, on the selective removal of resin composite and (c) the required “time taken”. BAG abrasive particles were characterised using scanning electron microscopy-energy dispersive X-ray spectrometry (SEM-EDX) and Fourier-transform infrared spectroscopy (FTIR). Standardised resin composite restorations created within an enamel analogue block (Macor™) in vitro, were removed using air-abrasion undersimulated clinical conditions. 90 standardised cavities were scanned before and after resin composite removal using laser profilometry and the volume of the resulting 3D images calculated. Multilevel linear model was used to identify the significant factors affecting Macor™ removal. BAG powder removed resin composite more selectively than conventional air-abrasion alumina powder using the same operating parameters (p < 0.001) and the effect of altering the unit's operating parameters was significant (p < 0.001). In conclusion, BAG powder is more efficient than alumina in the selective removal of resin composite particularly under specific operating parameters, and therefore may be recommended clinically as a method of preserving sound enamel structure when repairing and removing defective resin composite restorations.

Changes to Glazed Dental Ceramic Shade, Roughness, and Microhardness after Bleaching and Simulated Brushing.

Science.gov (United States)

Rodrigues, Carlos Roberto Teixeira; Turssi, Cecilia Pedroso; Amaral, Flávia Lucisano Botelho; Basting, Roberta Tarkany; França, Fabiana Mantovani Gomes

2017-09-05

To evaluate shade stability, surface roughness, microhardness, and compressive strength of a glazed feldspathic ceramic subjected to bleaching and simulated brushing. Eighty-eight glazed feldspathic ceramic specimens were made from microparticulate leucite and divided into eight groups (n = 10). The whitening products used were: Opalescence Trèswhite Supreme (Ultradent), Opalescence®\\ PF 15% (Ultradent), and Oral-B 3D White Whitestrips. All substances for whitening were used for 4 hours/day for a period of 14 days; the control group was not bleached. Next, half of the specimens were individually brushed. Microhardness and surface roughness data were subjected to three-way ANOVA and Tukey test. The diametrical tensile strength data were subjected to two-way ANOVA. The shade change data were analyzed using Kruskal-Wallis, Mann-Whitney, and the Student-Newman-Keuls test. The significance level was set at 5%. Glazed feldspathic ceramic surface microhardness was significantly affected by bleaching agents (p = 0.007). Initially, glazed ceramic microhardness was significantly higher than that observed after contact with the bleaching agents, whether or not brushing was performed. The specimens submitted to bleaching in preloaded trays presented lower surface roughness values after brushing (p = 0.037). The surface roughness was significantly lower in the brushed specimens (p = 0.044). The diametrical tensile strength was not significantly affected by the application of bleaching agents (p = 0.563) or by brushing (p = 0.477). When the specimens were brushed, however, shade change was significantly influenced by the bleaching agent used (p = 0.041). Bleaching agents associated with brushing cycles can alter surface properties and shade stability of glazed feldspathic ceramics, though such findings may not reflect the performance of unglazed feldspathic ceramics. © 2017 by the American College of Prosthodontists.

Maintenance and preservation of concrete structures. Report 3: Abrasion-erosion resistance of concrete

Science.gov (United States)

Liu, T. C.

1980-07-01

This report describes a laboratory test program on abrasion-erosion resistance of concrete, including the development of a new underwater abrasion-erosion test method. This program was designed to evaluate the relative abrasion-erosion resistance of various materials considered for use in the repair of erosion-damaged concrete structures. The test program encompassed three concrete types (conventional concrete, fiber-reinforced concrete, and polymer concrete); seven aggregate types (limestone, chert, trap rock, quartzite, granite, siliceous gravel, and slag); three principal water-cement rations (0.72, 0.54, and 0.40); and six types of surface treatment (vacuum, polyurethane coating, acrylic mortar coating, epoxy mortar coating, furan resin mortar coating, and iron aggregate topping). A total of 114 specimens made from 41 batches of concrete was tested. Based on the test data obtained, a comprehensive evaluation of the effects of various parameters on the abrasion-erosion resistance of concrete was presented. Materials suitable for use in the repair of erosion-damaged concrete structures were recommended. Additional work to correlate the reported findings with field performance was formulated.

21 CFR 884.1100 - Endometrial brush.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Endometrial brush. 884.1100 Section 884.1100 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL...) Indication: Only to evaluate the endometrium, and (ii) Contraindications: Pregnancy, history of uterine...

Friction Properties of Carbon Fiber Brush

OpenAIRE

大塚, 由佳; 月山, 陽介; 野老山, 貴行; 梅原, 徳次; OHTSUKA, Yuka; TSUKIYAMA, Yosuke; TOKOROYAMA, Takayuki; UMEHARA, Noritsugu

2011-01-01

直径数μmのカーボンファイバーを束ねたカーボンファイバーブラシ材料と金属材料のすべり摩擦におけるすべり出しの摩擦及び平均摩擦特性と,金属同士のそれらの摩擦特性の相違を調べ,カーボンファイバーブラシ材料の摩擦の特異性を明らかにした. Friction properties as initial and average friction coefficient were investigated for carbon brush materials. Experimental results shows that static friction coefficient of carbon fiber brush is smaller than kinetic friction after a macro slip. This phenomena is different from the usual friction properties between metals. I...

Abrasive Wear Resistance of the Iron- and WC-based Hardfaced Coatings Evaluated with Scratch Test Method

Directory of Open Access Journals (Sweden)

A. Vencl

2013-06-01

Full Text Available Abrasive wear is one of the most common types of wear, which makesabrasive wear resistance very important in many industries. Thehard facing is considered as useful and economical way to improve theperformance of components submitted to severe abrasive wear conditions, with wide range of applicable filler materials. The abrasive wear resistance of the three different hardfaced coatings (two iron‐based and one WC‐based, which were intended to be used for reparation of the impact plates of the ventilation mill, was investigated and compared. Abrasive wear tests were carried‐out by using the scratch tester under the dry conditions. Three normal loads of 10, 50 and 100 N and the constant sliding speed of 4 mm/s were used. Scratch test was chosen as a relatively easy and quick test method. Wear mechanism analysis showed significant influence of the hardfaced coatings structure, which, along with hardness, has determined coatings abrasive wear resistance.

Pre-polishing on a CNC platform with bound abrasive contour tools

Science.gov (United States)

Schoeffer, Adrienne E.

2003-05-01

Deterministic micorgrinding (DMG) of optical glasses and ceramics is the commercial manufacturing process of choice to shape glass surfaces prior to final finishing. This process employs rigid bound matrix diamond tooling resulting in surface roughness values of 3-51.tm peak to valley and 100-400nm rms, as well as mid-spatial frequency tool marks that require subsequent removal in secondary finishing steps. The ability to pre-polish optical surfaces within the grinding platform would reduce final finishing process times. Bound abrasive contour wheels containing cerium oxide, alumina or zirconia abrasives were constructed with an epoxy matrix. The effects of abrasive type, composition, and erosion promoters were examined for tool hardness (Shore D), and tested with commercial optical glasses in an OptiproTM CNC grinding platform. Metrology protocols were developed to examine tool wear and subsequent surface roughness. Work is directed to demonstrating effective material removal, improved surface roughness and cutter mark removal.

Experimental Study on Layered Ice Bonded Abrasive Polishing of Glass-ceramics

Directory of Open Access Journals (Sweden)

Yuli SUN

2014-12-01

Full Text Available Layered ice bonded abrasive tools (LIBAT is a new kind of one which not only has the ability of lapping and polishing but also has the effect of self-dressing. In this paper, two kinds of layered ice bonded abrasive tools were designed and manufactured. Experimental studies on layered ice bonded abrasive (LIBA polishing of glass-ceramics were conducted. The results show that the surface topography of glass-ceramics polished by micro α-Al2O3-nano α-Al2O3 LIBAT is better than that of polished by micro α-Al2O3-nano SiO2 LIBAT. The surface roughness Sa of glass-ceramics polished by the two kinds of LIBAT is at the nanometer scale. The reasons of this phenomenon were analyzed. The experimental results illustrate that the LIBAT shows good effect and can be used in production practice. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6149

HYDRO-ABRASIVE RESISTANCE AND MECHANICAL PROPERTIES OF CONCRETE WITH ADDED FLY ASH

OpenAIRE

Ristić, Nenad; Grdić, Zoran; Topličić-Ćurčić, Gordana

2015-01-01

The durability of hydraulic engineering structures mostly depends on the resistance of their concrete surfaces to mechanical abrasion. In this paper, we study the hydro-abrasive resistance and mechanical properties of concrete in which cement is partially replaced with fly ash in various proportions. To evaluate these concretes, we measured their compressive strength, flexural strength, static modulus of elasticity, ultrasound velocity through concrete, and sclerometer rebound. The hydro-abra...

Characterization of swollen structure of high-density polyelectrolyte brushes in salt solution by neutron reflectivity

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Motoyasu; Takahara, Atsushi [Institute for Materials Chemistry and Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan); Terayama, Yuki [Graduate School of Engineering, Kyushu University (Japan); Hino, Masahiro [Reactor Research Institute, Kyoto University (Japan); Ishihara, Kazuhiko, E-mail: takahara@cstf.kyushu-u.ac.j [Graduate School of Engineering, University of Tokyo (Japan)

2009-08-01

Zwitterionic and cationic polyelectrolyte brushes on quartz substrate were prepared by surface-initiated atom transfer radical polymerization of 2-(methacryloyloxy)ethyl phosphorylcholine (MPC) and 2-(methacryloyloxy)ethyltrimethylammonium chloride (METAC), respectively. The effects of ionic strength on brush structure and surface properties of densely grafted polyelectrolyte brushes were analysed by neutron reflectivity (NR) measurements. NR at poly(METAC)/D{sub 2}O and poly(MPC)/D{sub 2}O interface revealed that the grafted polymer chains were fairly extended from the substrate surface, while the thickness reduction of poly(METAC) brush was observed in 5.6 M NaCl/D{sub 2}O solution due to the screening of the repulsive interaction between polycations by hydrated salt ions. Interestingly, no structural change was observed in poly(MPC) brush even in a salt solution probably due to the unique interaction properties of phosphorylcholine units.

Design of a new abrasive slurry jet generator

Science.gov (United States)

Wang, F. C.; Shi, L. L.; Guo, C. W.

2017-12-01

With the advantages of a low system working pressure, good jet convergence and high cutting quality, abrasive slurry jet (ASJ) has broad application prospects in material cutting and equipment cleaning. Considering that the generator plays a crucial role in ASJ system, the paper designed a new type ASJ generator using an electric oil pump, a separate plunger cylinder, and a spring energized seal. According to the determining of structure shape, size and seal type, a new ASJ generator has been manufactured out and tested by a series of experiments. The new generator separates the abrasive slurry from the dynamic hydraulic oil, which can improve the service life of the ASJ system. And the new ASJ system can reach 40 MPa and has good performance in jet convergence, which deserves to popularization and application in materials machining.

Surface Grafted Glycopolymer Brushes to Enhance Selective Adhesion of HepG2 Cells

DEFF Research Database (Denmark)

Chernyy, Sergey; Jensen, Bettina Elisabeth Brøgger; Shimizu, Kyoko

2013-01-01

on the polymerization kinetics of 2-lactobionamidoethyl methacrylate) (LAMA) monomer on thermally oxidized silicon wafer. Both monolayer and multilayered aminosilane precursor layers have been prepared followed by reaction with 2-bromoisobutyrylbromide to form the ATRP initiator layer. It is inferred from the kinetic...... studies that the rate of termination is low on a multilayered initiator layer compared to a disordered monolayer structure. However both initiator types results in similar graft densities. Furthermore, it is shown that thick comb-like poly(LAMA) brushes can be constructed by initiating a second ATRP...... process on a previously formed poly(LAMA) brushes. The morphology of human hepatocellular carcinoma cancer cells (HepG2) on the comb-like poly(LAMA) brush layer has been studied. The fluorescent images of the HepG2 cells on the glycopolymer brush surface display distinct protrusions that extend outside...

Anthrax in Vintage Animal-hair Shaving Brushes

Centers for Disease Control (CDC) Podcasts

2017-08-08

Dr. Kate Hendricks, a CDC anthrax expert, discusses anthrax in vintage shaving brushes.  Created: 8/8/2017 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 8/8/2017.

Effects of hardness of abrasive grains on surface roughness of work piece in PVA bonded grinding wheel

International Nuclear Information System (INIS)

Nitta, S.; Takata, A.; Ishizaki, K.

2000-01-01

The purpose of this study is to clarify relation between hardness of abrasive grains and surface roughness of work piece in the case of PVA (Polyvinyl alcohol) bonded grinding wheels. Two PVA bonded grinding wheels; with diamond or silicon carbide as abrasive grains and grinding of glass and aluminum alloy was performed. The PVA bonded grinding wheels The PVA bonded grinding wheel with silicon carbide could not grind the glass. Because insufficiency in hardness, the PVA bonded grinding wheel with the diamond abrasive grains caused deep scratch on the aluminum alloy. It was found that the final surface roughness of the work piece was not proportional to the hardness of abrasive grains. The suitable hardness of abrasive grains will be obtained by the hardness of work piece. Copyright (2000) AD-TECH - International Foundation for the Advancement of Technology Ltd

Effects of Load and Speed on Wear Rate of Abrasive Wear for 2014 Al Alloy

Science.gov (United States)

Odabas, D.

2018-01-01

In this paper, the effects of the normal load and sliding speed on wear rate of two-body abrasive wear for 2014 Al Alloy were investigated in detail. In order to understand the variation in wear behaviour with load and speed, wear tests were carried out at a sliding distance of 11 m, a speed of 0.36 m/s, a duration of 30 s and loads in the range 3-11 N using 220 grit abrasive paper, and at a speed range 0.09-0.90 m/s, a load of 5 N and an average sliding distance of 11 m using abrasive papers of 150 grit size under dry friction conditions. Before the wear tests, solution treatment of the 2014 Al alloy was carried out at temperatures of 505 and 520 °C for 1 h in a muffle furnace and then quenched in cold water at 15 °C. Later, the ageing treatment was carried out at 185 °C for 8 h in the furnace. Generally, wear rate due to time increased linearly and linear wear resistance decreased with increasing loads. However, the wear rate was directly proportional to the load up to a critical load of 7 N. After this load, the slope of the curves decreased because the excessive deformation of the worn surface and the instability of the abrasive grains began to increase. When the load on an abrasive grain reaches a critical value, the groove width is about 0.17 of the abrasive grain diameter, and the abrasive grains begin to fail. The wear rate due to time increased slightly as the sliding speed increased in the range 0.09-0.90 m/s. The reason for this is that changes arising from strain rate and friction heating are expected with increasing sliding speeds.

Assessment of thermal spray coatings for wear and abrasion resistance applications

Science.gov (United States)

Karode, Ishaan Nitin

Thermal spray cermet and metallic coatings are extensively used for wear, abrasion and corrosion control in a variety of industries. The first part of the thesis focuses mainly on testing of sand erosion resistance of thermal spray coatings on carbon composites used in the manufacture of helicopter rotor blades. The test set-up employed is a sand blasting machine and is an effort to duplicate the in-flight conditions especially those encountered in hot arid conditions. The technique adopted follows the Department of Defence test method standard. Carbon Composites have excellent stiffness, strength and low weight/density. The strength to weight ratio is high. Hence, these are used in aerospace applications to a large extent. However, the biggest problem encountered with carbon composites is its low abrasion resistance as its surface is very weak. Hence, thermal spray coatings are used to improve the surface properties of CFRP. Zinc bond coats and WC-Co coatings were tested. However, high amount of thermal stresses were developed between the substrate and the coating due to large differences in the CTE's of the both, leading to high mass losses within two minutes and just 130 grams of sand sprayed on to the coatings with the sand blasting machine built; and hence the coatings with CC as a substrate could not qualify for the application. The second part of the thesis focuses on the assessment of different thermal spray coatings used for manufacture of mechanical seals in pumps and analyze the best coating material for the wear resistance application through detail quantification of material loss by block-on-ring test set-up. A machine based on Block-on-ring test set-up following ASTM G77 (Measurement of Adhesive wear resistance of thermal spray coatings) standards was built to duplicate the pump conditions. Thermally sprayed coated materials were tested in different conditions (Load, time, abrasive). WC-Co had the highest wear resistance (lower volume losses) and

Controls on wind abrasion patterns through a fractured bedrock landscape

Science.gov (United States)

Perkins, J. P.; Finnegan, N. J.

2017-12-01

Wind abrasion is an important geomorphic process for understanding arid landscape evolution on Earth and interpreting the post-fluvial history of Mars. Both the presence and orientation of wind-abraded landforms provide potentially important constraints on paleo-climatic conditions; however, such interpretations can be complicated by lithologic and structural heterogeneity. To explore the influence of pre-existing structure on wind abrasion, we exploit a natural experiment along the 10.2 Ma Lower Rio San Pedro ignimbrite in northern Chile. Here, a 3.2 Ma andesite flow erupted from Cerro de las Cuevas and deposited atop the ignimbrite, supplying wind-transportable sediment and initiating a phase of downwind abrasion. Additionally, the lava flow provides a continually varying degree of upwind topographic shielding along the ignimbrite that is reflected in a range of surface morphologies. Where fully shielded the ignimbrite surface is partially blanketed by sediment. However, as relief decreases the surface morphology shifts from large polygonal structures that emerge due to the concentration of wind abrasion along pre-existing fracture sets, to polygons that are bisected by wind-parallel grooves that cross-cut fracture sets, to linear sets of yardangs. We reconstruct the ignimbrite surface using a high-resolution digital elevation model, and calculate erosion rates ranging from 0.002 to 0.45 mm/kyr that vary strongly with degree of topographic shielding (R2 = 0.97). We use measured abrasion rates together with nearby weather station data to estimate the nondimensional Rouse number and Inertial Parameter for a range of particle sizes. From these calculations, we hypothesize that the change from fracture-controlled to flow-controlled morphology reflects increases in the grain size and inertia of particles in the suspension cloud. Where the ignimbrite experiences persistent high winds, large particles may travel in suspension and are largely insensitive to topographic

Changes in intestinal absorption of nutrients and brush border glycoproteins after total parenteral nutrition in rats.

Science.gov (United States)

Miura, S; Tanaka, S; Yoshioka, M; Serizawa, H; Tashiro, H; Shiozaki, H; Imaeda, H; Tsuchiya, M

1992-01-01

The effect of total parenteral nutrition on nutrients absorption and glycoprotein changes of brush border membrane was examined in rat small intestine. In total parenteral nutrition rats, a marked decrease in activity of brush border enzymes was observed mainly in the proximal and middle segments of the intestine. Galactose perfusion of jejunal segment showed that hexose absorption was significantly inhibited, while intestinal absorption of glycine or dipeptide, glycylglycine was not significantly affected by total parenteral nutrition treatment. When brush border membrane glycoprotein profile was examined by [3H]-glucosamine or [3H]-fucose incorporation into jejunal loops, significant changes were observed in the glycoprotein pattern of brush border membrane especially in the high molecular weight range over 120 kDa after total parenteral nutrition treatment, suggesting strong dependency of glycoprotein synthesis on luminal substances. Molecular weight of sucrase isomaltase in brush border membrane detected by specific antibody showed no significant difference, however, in total parenteral nutrition and control rats. Also, molecular weight of specific sodium glucose cotransporter of intestinal brush border membrane detected by selective photoaffinity labelling was not altered in total parenteral nutrition rats. It may be that prolonged absence of oral food intake may produce significant biochemical changes in brush border membrane glycoprotein and absorptive capacity of small intestine, but these changes were not observed in all brush border membrane glycoproteins. Images Figure 1 Figure 2 Figure 3 Figure 4 PMID:1582592

Polyelectrolyte Properties in Mono and Multi-Valent Ionic Media: Brushes and Complex Coacervates

Science.gov (United States)

Farina, Robert M.

Materials composed of polyelectrolytes have unique and interesting physical properties resulting primarily from their charged monomer segments. Polyelectrolytes, which exist in many different biological and industrial forms, have also been shown to be highly responsive to external environmental changes. Here, two specific polyelectrolyte systems, brushes and complex coacervates, are discussed in regards to how their properties can be tailored by adjusting the surrounding ionic environment with mono and multi-valent ions. End-tethered polyelectrolyte brushes, which constitute an interesting and substantial portion of polyelectrolyte applications, are well known for their ability to provide excellent lubrication and low friction when coated onto surfaces (e.g. articular cartilage and medical devices), as well as for their ability to stabilize colloidal particles in solution (e.g. paint and cosmetic materials). These properties have been extensively studied with brushes in pure mono-valent ionic media. However, polyelectrolyte brush interactions with multi-valent ions in solution are much less understood, although highly relevant considering mono and multi-valent counterions are present in most applications. Even at very low concentrations of multi-valent ions in solution, dramatic polyelectrolyte brush physical property changes can occur, resulting in collapsed chains which also adhere to one another via multi-valent bridging. Here, the strong polyelectrolyte poly(sodium styrene sulfonate) was studied using the Surface Forces Apparatus (SFA) and electrochemistry in order to investigate brush height and intermolecular interactions between two brushes as a function of multi-valent counterion population inside a brush. Complex coacervates are formed when polyanions and polycations are mixed together in proper conditions of an aqueous solution. This mixing results in a phase separation of a polymer-rich, coacervate phase composed of a chain network held together via

Obstructive jaundice: a comparative study of forceps and brush biopsy under percutaneous transhepatic cholangiography

International Nuclear Information System (INIS)

Li Yongdong; Han Xinwei; Wu Gang; Ma Bo; Xing Gusheng

2004-01-01

Objective: To compare the sensitivity between forceps biopsy and brushing, and to explore a feasible approach to pathological diagnosis of the obstructive jaundice. Methods: 92 consecutive patients with obstructive jaundice underwent transluminal forceps biopsy and brushing during percutaneous transhepatic cholangiography and percutaneous transhepatic cholangiodrainage. The technique was performed through a preexisting percutaneous transhepatic tract with multiple specimens obtained after passing the forceps biopsy or brush into a 8-French sheath. Finally the specimens were fixed with formalin for pathologic or cytologic diagnosis. Results: The histopathologic diagnosis was acquired in 81 out of 92 patients with forceps biopsy reaching the successful rate of 97.83%. Sensitivity of forceps biopsy in 92 patients was higher than that of brush in 84 patients (88.04% vs 76.19% χ 2 =4.251, P= <0.05). Conclusions: Percutaneous transhepatic cholangiobiopsy is a simple technique with minimal invasion, high sensitivity and worthy to be used spread extensively. Percutaneous transluminal brush cytology is also an useful method for establishing a diagnosis of cholangiocarcinoma. (authors)

Nuclear-chemical methods in a hard tooth tissue abrasion study

International Nuclear Information System (INIS)

Gosman, A.; Spevacek, V.; Konicek, J.; Vopalka, D.; Housova, D.; Dolezalova, L.

1999-01-01

The advanced method consists in implantation-labelling of the thin surface layers of the solid objects, e.g. hard tooth tissue, by atoms of suitable natural or artificial radionuclides. Nuclides from the uranium series were implanted into the surface by using nuclear recoil effect at alpha decay of 226 Ra to 222 Rn, alpha decay of 222 Rn to RaA, alpha decay of RaA to RaB (beta-emitter) and further alpha or beta emitters. With regard to chosen alpha detection and to the half-lives of the radionuclides, there was actually measured the activity of 222 Rn, RaA and RaC' in the thin surface layer. This was followed by the laboratory simulation of the abrasion in the system of 'toothbrush - various suspensions of the tooth-pastes - hard tooth tissue (or material standard - ivory)' in specially designed device - the dentoabrasion meter. The activities of the tissue surface measured before and after abrasion were used for calculations of the relative drop of the surface activity. On this basis the influence of various tooth-pastes containing various abrasive substances was determined. (author)

The Effect of Machining Conditions on the Forces in the Process of Roller Brush Machining

Directory of Open Access Journals (Sweden)

Jakub Matuszak

2017-12-01

Full Text Available Because of its advantages, brushing processing has many uses. The main ones include the removal of corrosion products, surface cleaning, deburring and shaping the properties of the surface layer. The intensity of these processes depends on the degree of impact of brush fibres on the work surface. In the case of tools, in which the resilient fibres are the working elements, forces in the brushing process, apart from the machining parameters, depend on the characteristics and overall dimensions of individual fibres. The paper presents the results of studies of the influence of technological parameters and type of fibres on the radial force in the brushing process.

Effectiveness of the bucco-lingual technique within a school-based supervised toothbrushing program on preventing caries: a randomized controlled trial

Directory of Open Access Journals (Sweden)

Frazão Paulo

2011-03-01

Full Text Available Abstract Background Supervised toothbrushing programs using fluoride dentifrice have reduced caries increment. However there is no information about the effectiveness of the professional cross-brushing technique within a community intervention. The aim was to assess if the bucco-lingual technique can increase the effectiveness of a school-based supervised toothbrushing program on preventing caries. Methods A randomized double-blinded controlled community intervention trial to be analyzed at an individual level was conducted in a Brazilian low-income fluoridated area. Six preschools were randomly assigned to the test and control groups and 284 five-year-old children presenting at least one permanent molar with emerged/sound occlusal surface participated. In control group, oral health education and dental plaque dying followed by toothbrushing with fluoride dentifrice supervised directly by a dental assistant, was developed four times per year. At the remaining school days the children brushed their teeth under indirect supervising of the teachers. In test group, children also underwent a professional cross-brushing on surfaces of first permanent molar rendered by a specially trained dental assistant five times per year. Enamel and dentin caries were recorded on buccal, occlusal and lingual surfaces of permanent molars during 18-month follow-up. Exposure time of surfaces was calculated and incidence density ratio was estimated using Poisson regression model. Results Difference of 21.6 lesions per 1,000 children between control and test groups was observed. Among boys whose caries risk was higher compared to girls, incidence density was 50% lower in test group (p = 0.016. Conclusion Modified program was effective among the boys. It is licit to project a relevant effect in a larger period suggesting in a broader population substantial reduction of dental care needs. Trial registration ISRCTN18548869.

Self-consistent field theory of protein adsorption in a non-Gaussian polyelectrolyte brush

NARCIS (Netherlands)

Biesheuvel, P.M.; Leermakers, F.A.M.; Stuart, M.A.C.

2006-01-01

To describe adsorption of globular protein molecules in a polyelectrolyte brush we use the strong-stretching approximation of the Edwards self-consistent field equation, combined with corrections for a non-Gaussian brush. To describe chemical potentials in this mixture of (globular) species of

Air-propelled abrasive grit can damage the perennial weed, quackgrass, Elytrigia repens (L.) Nevski

Science.gov (United States)

New techniques are needed to control quackgrass in organic crops. With greater than or equal to 2 applications of abrasive air-propelled (800 kPa) corncob grit to 15 cm tall quackgrass tillers, regrowth was minimal at 5 weeks after treatment. Abrasive grits may be effective tools to help manage pere...

Scaling features of the tribology of polymer brushes of increasing grafting density around the mushroom-to-brush transition.

Science.gov (United States)

Mayoral, E; Klapp, J; Gama Goicochea, A

2017-01-01

Nonequilibrium coarse-grained, dissipative particle dynamics simulations of complex fluids, made up of polymer brushes tethered to planar surfaces immersed in a solvent yield nonmonotonic behavior of the friction coefficient as a function of the polymer grating density on the substrates, Γ, while the viscosity shows a monotonically increasing dependence on Γ. This effect is shown to be independent of the degree of polymerization, N, and the size of the system. It arises from the composition and the structure of the first particle layer adjacent to each surface that results from the confinement of the fluid. Whenever such layers are made up of as close a proportion of polymer beads to solvent particles as there are in the fluid, the friction coefficient shows a minimum, while for disparate proportions the friction coefficient grows. At the mushroom-to-brush transition (MBT) the viscosity scales with an exponent that depends on the characteristic exponent of the MBT (6/5) and the solvent quality exponent (ν=0.5, for θsolvent), but it is independent of the polymerization degree (N). On the other hand, the friction coefficient at the MBT scales as μ∼N^{6/5}, while the grafting density at the MBT scales as Γ∼N^{-6/5} when friction is minimal, in agreement with previous scaling theories. We argue these aspects are the result of cooperative phenomena that have important implications for the understanding of biological brushes and the design of microfluidics devices, among other applications of current academic and industrial interest.

Development of plastic elongation in nanocrystalline and amorphous Ni–W dual phase alloys by brushing technique

International Nuclear Information System (INIS)

Nakayama, S.; Adachi, H.; Yamasaki, T.

2015-01-01

Highlights: • A novel agitation technique called the brushing technique is proposed. • A homogeneous material can be obtained with the brushing technique. • The brushed material exhibits large plastic elongation with work hardening. - Abstract: A novel agitation technique, referred to as the “brushing technique” is proposed to treat the surface of a Ni–W alloy film during electrodeposition. This technique was developed to directly remove hydrogen bubbles on the film surface and to apply Ni ions to the interfacial layer with the substrate. The intrinsic mechanical properties of the Ni–W electrodeposits are then evaluated with respect to application. High resolution transmission electron microscopy observations revealed that both treated and untreated films have nanocrystallites of approximately 5 nm in diameter and an amorphous phase. There was a compositional difference of about. 1.4 at% W between the face side and the reverse side of the film that was not subjected to the brushing technique, whereas this difference was absent in the film subjected to the brushing technique. In addition, the brushing technique reduced the surface roughness of the film and decreased the number of defects. As a result, a large plastic strain of about. 2.9% was observed with work hardening under tensile testing

Interfacial Friction and Adhesion of Polymer Brushes

KAUST Repository

Landherr, Lucas J. T.; Cohen, Claude; Agarwal, Praveen; Archer, Lynden A.

2011-01-01

higher molar mass chains exhibit higher friction forces than those created using lower molar mass polymers. Increased grafting density of chains in the brush significantly reduces the COF by creating a uniform surface of stretched chains with a decreased

Two-body, dry abrasive wear of Fe/Cr/C experimental alloys - relationship between microstructure and mechanical properties

International Nuclear Information System (INIS)

Kwok, C.K.S.

1982-01-01

A systematic study of abrasive wear resistance of Fe/Cr/Mn based alloys has been carried out using a two body pin-on-disc wear machine. Abrasives used were silicon carbide, alumina and quartz. The objective of this study was to evaluate the abrasive wear resistance and to investigate the relationships between microstructure, mechanical properties, and abrasive wear resistance for these experimental alloys. Several commercial alloys were also tested to provide a basis for comparison. The goal of this study was to develop information so as to improve wear resistance of these experimental alloys by means of thermal treatments. Grain-refinement by double heat treatment was carried out in this research

Thermal annealing and ionic abrasion in ZnTe

International Nuclear Information System (INIS)

Bensahel, D.

1975-01-01

Thermal annealing of the ZnTe crystal is studied first in order to obtain information on the aspect of the penetration profile. Ionic abrasion is then investigated to find out whether it produces the same effects as ionic implantation, especially for luminescence [fr

RAFT-mediated synthesis of cationic poly[(ar-vinylbenzyl)trimethylammonium chloride] brushes for quantitative DNA immobilization

International Nuclear Information System (INIS)

Demirci, Serkan; Caykara, Tuncer

2013-01-01

The synthesis of cationic poly[(ar-vinylbenzyl)trimethylammonium chloride)] [poly(VBTAC)] brushes was achieved via reversible addition-fragmentation chain transfer (RAFT) polymerization and used for quantitative DNA immobilization. Initially, silicon surfaces were modified with RAFT chain transfer agent by utilizing an amide reaction involving a silicon wafer modified with allylamine and 4-cyanopentanoic acid dithiobenzoate (CPAD). Poly(VBTAC) brushes were then prepared via RAFT-mediated polymerization from the surface immobilized CPAD. Various characterization techniques including ellipsometry, X-ray photoelectron spectroscopy, grazing angle-Fourier transform infrared spectroscopy, atomic force microscopy and contact-angle goniometer were used to characterize the immobilization of CPAD on the silicon wafer and the subsequent polymer formation. The addition of free CPAD was required for the formation of well-defined polymer brushes, which subsequently resulted in the presence of free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. Moreover, from atomic force microscopy and ellipsometry measurements, it was also determined that the density of immobilized DNA on the cationic poly(VBTAC) brushes can be quantitatively controlled by adjusting the solution concentration. Highlights: ► The cationic poly(VBTAC) brushes were prepared by RAFT polymerization. ► Grafting density of cationic poly(VBTAC) brushes was as high as 0.76 chains/nm 2 . ► The cationic poly(VBTAC) brushes were used for quantitative DNA immobilization.

Assessment of mechanical and three-body abrasive wear peculiarity ...

Indian Academy of Sciences (India)

directional fabric reinforcement offers a unique solution for ... showed good performance to the three-body abrasive wear. .... plied by the Pioneer Chemical Company, Delhi, India. ..... Theoretical and measured densities of composites, along.

Intestinal alkaline phosphatase: selective endocytosis from the enterocyte brush border during fat absorption

DEFF Research Database (Denmark)

Hansen, Gert Helge; Niels-Christiansen, Lise-Lotte; Immerdal, Lissi

2007-01-01

explants. By immunofluorescence microscopy, fat absorption caused a translocation of IAP from the enterocyte brush border to the interior of the cell, whereas other brush-border enzymes were unaffected. By electron microscopy, the translocation occurred by a rapid (5 min) induction of endocytosis via...

Turning of wood plastic composites by water jet and abrasive water jet

OpenAIRE

Hutyrová, Z.; Ščučka, J. (Jiří); Hloch, S. (Sergej); Hlaváček, P. (Petr); Zeleňák, M. (Michal)

2015-01-01

The paper deals with the verification of suitability of water jet and abrasive water jet application for the disintegration of rotating samples of wood plastic composites (WPCs) with diameter d=36 mm. The influence of selected technological factors (traverse speed of cutting head v [mm/ min] and size of abrasive particles [MESH]) on the topography of resulting surfaces has in particular been studied. Surface topography and quality have been assessed using the methods of optical and co...

Monitoring of the Abrasion Processes (by the Example of Alakol Lake, Republic of Kazakhstan)

Science.gov (United States)

Abitbayeva, Ainagul; Valeyev, Adilet; Yegemberdiyeva, Kamshat; Assylbekova, Aizhan; Ryskeldieva, Aizhan

2016-01-01

The purpose of the study is to analyze the abrasion processes in the regions of dynamically changing Alakol lake shores. Using the field method, methods of positioning by the GPS receiver and interpretation of remote sensing data, the authors determined that abrasion processes actively contributed to the formation the modern landscape, causing the…

In vitro assessment of 3 dentifrices containing fluoride in preventing demineralization of overdenture abutments and root surfaces.

Science.gov (United States)

Goettsche, Zachary S; Ettinger, Ronald L; Wefel, James S; Hogan, Mary M; Harless, Jeffery D; Qian, Fang

2014-11-01

Caries development under overdentures has been a continuing problem and requires the daily use of fluoride to prevent demineralization. The purpose of this in vitro study was to compare the effectiveness of dentifrices containing tricalcium phosphate or calcium phosphosilicate in combination with fluoride to prevent the demineralization of overdenture abutments and root surfaces. A total of 56 caries-free extracted teeth were prepared as overdenture abutments. The teeth were painted with acid-resistant varnish, leaving one 1×4-mm window on occlusal and root surfaces. The teeth were randomly divided into 4 groups: a control group treated with distilled/deionized water only, a group treated with ClinPro 5000, a group treated with ReNew, and a group treated with Prevident 5000 gel. Each tooth was subjected to a demineralizing/remineralizing cycling protocol for 12 days with the appropriate treatment products. The teeth were sectioned longitudinally through both windows. Photomicrographs were made of 3 representative sections from each tooth. A representative section was defined as one that included both windows and was cut from the part of the tooth that had the flattest surface to reduce the edge effect. The depths of the lesions were measured on representative sections from each group. A 1-way MANOVA and a 1-way ANOVA with the post hoc Tukey-Kramer test were used to evaluate the treatment effects on the criterion variables (α=.05). The total lesion depths of the control teeth on the occlusal surface were not statistically significantly deeper than for the 3 dentifrices (P=.7705). However, all 3 dentifrices had narrower cavitation depths than the control (mean cavitation band depth, 43.59 [ReNew] versus 37.99 [Prevident 5000 gel] versus 36.70 [ClinPro 5000] versus 246.86 [control]) (Pteeth treated with Prevident 5000 gel had the shallowest total lesion depth and were statistically significantly different from those treated with ReNew and Clin

Effects of carbon brush anode size and loading on microbial fuel cell performance in batch and continuous mode

KAUST Repository

Lanas, Vanessa; Ahn, Yongtae; Logan, Bruce E.

2014-01-01

Larger scale microbial fuel cells (MFCs) require compact architectures to efficiently treat wastewater. We examined how anode-brush diameter, number of anodes, and electrode spacing affected the performance of the MFCs operated in fed-batch and continuous flow mode. All anodes were initially tested with the brush core set at the same distance from the cathode. In fed-batch mode, the configuration with three larger brushes (25 mm diameter) produced 80% more power (1240 mW m-2) than reactors with eight smaller brushes (8 mm) (690 mW m-2). The higher power production by the larger brushes was due to more negative and stable anode potentials than the smaller brushes. The same general result was obtained in continuous flow operation, although power densities were reduced. However, by moving the center of the smaller brushes closer to the cathode (from 16.5 to 8 mm), power substantially increased from 690 to 1030 mW m-2 in fed batch mode. In continuous flow mode, power increased from 280 to 1020 mW m-2, resulting in more power production from the smaller brushes than the larger brushes (540 mW m-2). These results show that multi-electrode MFCs can be optimized by selecting smaller anodes, placed as close as possible to the cathode. © 2013 Elsevier B.V. All rights reserved.

Effects of carbon brush anode size and loading on microbial fuel cell performance in batch and continuous mode

KAUST Repository

Lanas, Vanessa

2014-02-01

Larger scale microbial fuel cells (MFCs) require compact architectures to efficiently treat wastewater. We examined how anode-brush diameter, number of anodes, and electrode spacing affected the performance of the MFCs operated in fed-batch and continuous flow mode. All anodes were initially tested with the brush core set at the same distance from the cathode. In fed-batch mode, the configuration with three larger brushes (25 mm diameter) produced 80% more power (1240 mW m-2) than reactors with eight smaller brushes (8 mm) (690 mW m-2). The higher power production by the larger brushes was due to more negative and stable anode potentials than the smaller brushes. The same general result was obtained in continuous flow operation, although power densities were reduced. However, by moving the center of the smaller brushes closer to the cathode (from 16.5 to 8 mm), power substantially increased from 690 to 1030 mW m-2 in fed batch mode. In continuous flow mode, power increased from 280 to 1020 mW m-2, resulting in more power production from the smaller brushes than the larger brushes (540 mW m-2). These results show that multi-electrode MFCs can be optimized by selecting smaller anodes, placed as close as possible to the cathode. © 2013 Elsevier B.V. All rights reserved.

Aggregation of plaque disclosing agent in a dentifrice Incorporação de evidenciador de placa bacteriana a um dentifrício

Directory of Open Access Journals (Sweden)

Débora Dias da Silva

2004-06-01

Full Text Available Dental plaque removal is an important issue in health promotion. Toothbrushing is one of the main methods employed for such purpose, since it can prevent dental caries by means of the fluoride present in the dentifrice. Dentifrices might contain plaque disclosing agents and thus allow dental plaque observation. The aim of this study was to assess whether utilization of a plaque disclosing agent interfered with plaque removal among adolescents, as well as the difference between utilization of erythrosine tablets and dentifrices containing plaque disclosing agent. The sample was composed of 62 students from Piracicaba, SP, Brazil, aged 12 to 14 years old, divided into 3 groups: G1 or control group (toothbrushing without plaque disclosure; G2 (plaque disclosing with an erythrosine tablet and toothbrushing and G3 (toothbrushing with dentifrice containing plaque disclosing agent. After toothbrushing, disclosure of the remaining dental plaque was performed in all groups with a fuchsin tablet and measured through the Simplified Oral Health Assessment Index (OHI-S, in two stages with a 2-month interval between them. The analysis of variance (ANOVA showed that there was no difference in the OHI-S index between the groups (p>0.05, however the G3 displayed a higher proportion of students with plaque reduction (23% than G2 (21%, besides the smallest difference in the mean remaining dental plaque. There was no difference between groups; however, it was suggested that the dentifrice with plaque disclosing agent had positive results in relation to the erythrosine tablet, even though the small sample size may have interfered with the results, indicating the need of complementary studies.Na promoção de saúde, a remoção da placa bacteriana é um fator importante e um dos métodos que incentivam sua remoção, é a escovação dentária, podendo-se prevenir a cárie dental através do íon flúor dos dentifrícios. Estes podem conter evidenciadores

Surface interaction forces of cellulose nanocrystals grafted with thermoresponsive polymer brushes.

Science.gov (United States)

Zoppe, Justin O; Osterberg, Monika; Venditti, Richard A; Laine, Janne; Rojas, Orlando J

2011-07-11

The colloidal stability and thermoresponsive behavior of poly(N-isopropylacrylamide) brushes grafted from cellulose nanocrystals (CNCs) of varying graft densities and molecular weights was investigated. Indication of the grafted polymer brushes was obtained after AFM imaging of CNCs adsorbed on silica. Also, aggregation of the nanoparticles carrying grafts of high degree of polymerization was observed. The responsiveness of grafted CNCs in aqueous dispersions and as an ultrathin film was evaluated by using light scattering, viscosimetry, and colloidal probe microscopy (CPM). Light transmittance measurements showed temperature-dependent aggregation originating from the different graft densities and molecular weights. The lower critical solution temperature (LCST) of grafted poly(NiPAAm) brushes was found to decrease with the ionic strength, as is the case for free poly(NiPAAm) in aqueous solution. Thermal responsive behavior of grafted CNCs in aqueous dispersions was observed by a sharp increase in dispersion viscosity as the temperature approached the LCST. CPM in liquid media for asymmetric systems consisting of ultrathin films of CNCs and a colloidal silica probe showed the distinctive effects of the grafted polymer brushes on interaction and adhesive forces. The origin of such forces was found to be mainly electrostatic and steric in the case of bare and grafted CNCs, respectively. A decrease in the onset of attractive and adhesion forces of grafted CNCs films were observed with the ionic strength of the aqueous solution. The decreased mobility of polymer brushes upon partial collapse and decreased availability of hydrogen bonding sites with higher electrolyte concentration were hypothesized as the main reasons for the less prominent polymer bridging between interacting surfaces.

Assessment of Rail Seat Abrasion Patterns and Environment

Science.gov (United States)

2012-05-01

Rail seat abrasion (RSA) of concrete ties is manifested by the loss of material under the rail seat area and, in extreme cases, results in loss of rail clip holding power, reverse rail cant, and gauge widening. RSA was measured in several curves on t...

Manufacturing of copper-graphite brushes for automobile applications

International Nuclear Information System (INIS)

Answar, M.Y.

2006-01-01

Copper-graphite brushes are used in high-volume automotive applications, such as ignition switches, window lifts, wiper motors, engine cooling fans, ABS break system and seat actuators etc. The amount of graphite in these brushes may range from 5 -20 wt. %. In this paper, some of the results of a study carried out using locally produced electrolytic copper powder and imported graphite powder are being summarized. The green compacts were produced by compaction at 650 MPa. These compacts were sintered at temperatures between 950 to 1050 degree C for various time intervals. The effects of sintering temperatures and time on the properties are analyzed. The influence of small additions of zinc on hardness of the sintered alloy compacts is also investigated. (author)

Cross Sectional: bilateral parent-child interactions in school-age children's tooth-brushing behaviors.

Science.gov (United States)

Goh, Esther C L; Hsu, Stephen Chin-Ying

2013-01-01

The purpose of this study was to examine bilateral dynamics between parents and children in influencing children's tooth-brushing behaviors. In-depth conversational interviews-a specific qualitative method-were conducted with 38 parents in urban Xiamen, China and Singapore to learn insights into parental strategies for encouraging tooth-brushing habits in 6- to 9-year-old children. The interviews also examined the range of responses from children toward these parental strategies. Children usually do not comply with these tooth-brushing instructions from parents without a process of negotiation. Children's responses ranged from active resistant to compliant. Parents in Xiamen tended to use softer strategies and were more prone to be emotionally and behaviorally influenced by children's effort to thwart these strategies. Conversely, Singapore parents tended to demonstrate greater tenacity in negotiating with children. The process of developing children's tooth-brushing habits is not a unilateral from-parent-to-children process. Instead, it should be conceptualized as an ongoing interaction with bilateral power of influence from both parties.

Novel Strategy for Photopatterning Emissive Polymer Brushes for Organic Light Emitting Diode Applications.

Science.gov (United States)

Page, Zachariah A; Narupai, Benjaporn; Pester, Christian W; Bou Zerdan, Raghida; Sokolov, Anatoliy; Laitar, David S; Mukhopadhyay, Sukrit; Sprague, Scott; McGrath, Alaina J; Kramer, John W; Trefonas, Peter; Hawker, Craig J

2017-06-28

A light-mediated methodology to grow patterned, emissive polymer brushes with micron feature resolution is reported and applied to organic light emitting diode (OLED) displays. Light is used for both initiator functionalization of indium tin oxide and subsequent atom transfer radical polymerization of methacrylate-based fluorescent and phosphorescent iridium monomers. The iridium centers play key roles in photocatalyzing and mediating polymer growth while also emitting light in the final OLED structure. The scope of the presented procedure enables the synthesis of a library of polymers with emissive colors spanning the visible spectrum where the dopant incorporation, position of brush growth, and brush thickness are readily controlled. The chain-ends of the polymer brushes remain intact, affording subsequent chain extension and formation of well-defined diblock architectures. This high level of structure and function control allows for the facile preparation of random ternary copolymers and red-green-blue arrays to yield white emission.

Tribological properties of multifunctional coatings with Shape Memory Effect in abrasive wear

Science.gov (United States)

Blednova, Zh. M.; Dmitrenko, D. V.; Balaev, E. U. O.

2018-01-01

The article gives research results of the abrasive wear process on samples made of Steel 1045, U10 and with applied composite surface layer "Nickel-Multicomponent material with Shape Memory Effect (SME) based on TiNi". For the tests we have chosen TiNiZr, which is in the martensite state and TiNiHfCu, which is in the austenitic state at the test temperature. The formation of the surface layer was carried out by high-speed oxygen-fuel deposition in a protective atmosphere of argon. In the wear test, Al2O3 corundum powder was used as an abrasive. It is shown that the wear rate of samples with a composite surface layer of multicomponent materials with SME is significantly reduced in comparison with the base, which is explained by reversible phase transformations of the surface layer with SME. After carrying out the additional surface plastic deformation (SPD), the resistance of the laminated composition to abrasion wear has greatly enhanced, due to the reinforcing effect of the SPD. It is recommended for products working in conditions of abrasive wear and high temperatures to use the complex formation technology of the surface composition "steel-nickel-material with high-temperature SME", including preparation of the substrate surface and the deposited material, high-speed spraying in the protective atmosphere of argon, followed by SPD.

Real-time x-ray scattering study of the initial growth of organic crystals on polymer brushes

Energy Technology Data Exchange (ETDEWEB)

An, Sung Yup; Ahn, Kwangseok; Kim, Doris Yangsoo; Lee, Dong Ryeol, E-mail: drlee@ssu.ac.kr [Department of Physics, Soongsil University, Seoul 156-743 (Korea, Republic of); Lee, Hyun-Hwi [Pohang Accelerator Laboratory, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); Cho, Jeong Ho, E-mail: jhcho94@skku.edu [Department of Chemical Engineering, SKKU Advanced Institute of Nanotechnology (SAINT) and Center for Human Interface Nano Technology (HINT), Sungkyunkwan University, Suwon 440-476 (Korea, Republic of)

2014-04-21

We studied the early-stage growth structures of pentacene organic crystals grown on polymer brushes using real-time x-ray scattering techniques. In situ x-ray reflectivity and atomic force microscopy analyses revealed that at temperatures close to the glass transition temperature of polymer brush, the pentacene overlayer on a polymer brush film showed incomplete condensation and 3D island structures from the first monolayer. A growth model based on these observations was used to quantitatively analyze the real-time anti-Bragg x-ray scattering intensities measured during pentacene growth to obtain the time-dependent layer coverage of the individual pentacene monolayers. The extracted total coverage confirmed significant desorption and incomplete condensation in the pentacene films deposited on the polymer brushes. These effects are ascribed to the change in the surface viscoelasticity of the polymer brushes around the glass transition temperature.

Resistance to abrasion of extrinsic porcelain esthetic characterization techniques.

Science.gov (United States)

Chi, Woo J; Browning, William; Looney, Stephen; Mackert, J Rodway; Windhorn, Richard J; Rueggeberg, Frederick

2017-01-01

A novel esthetic porcelain characterization technique involves mixing an appropriate amount of ceramic colorants with clear, low-fusing porcelain (LFP), applying the mixture on the external surfaces, and firing the combined components onto the surface of restorations in a porcelain oven. This method may provide better esthetic qualities and toothbrush abrasion resistance compared to the conventional techniques of applying color-corrective porcelain colorants alone, or applying a clear glaze layer over the colorants. However, there is no scientific literature to support this claim. This research evaluated toothbrush abrasion resistance of a novel porcelain esthetic characterization technique by subjecting specimens to various durations of simulated toothbrush abrasion. The results were compared to those obtained using the conventional characterization techniques of colorant application only or colorant followed by placement of a clear over-glaze. Four experimental groups, all of which were a leucite reinforced ceramic of E TC1 (Vita A1) shade, were prepared and fired in a porcelain oven according to the manufacturer's instructions. Group S (stain only) was characterized by application of surface colorants to provide a definitive shade of Vita A3.5. Group GS (glaze over stain) was characterized by application of a layer of glaze over the existing colorant layer as used for Group S. Group SL (stain+LFP) was characterized by application of a mixture of colorants and clear low-fusing add-on porcelain to provide a definitive shade of Vita A3.5. Group C (Control) was used as a control without any surface characterization. The 4 groups were subjected to mechanical toothbrushing using a 1:1 water-to-toothpaste solution for a simulated duration of 32 years of clinical use. The amount of wear was measured at time intervals simulating every 4 years of toothbrushing. These parameters were evaluated longitudinally for all groups as well as compared at similar time points among

Hydrogel brushes grafted from stainless steel via surface-initiated atom transfer radical polymerization for marine antifouling

Energy Technology Data Exchange (ETDEWEB)

Wang, Jingjing, E-mail: jjwang1@hotmail.com; Wei, Jun

2016-09-30

Highlights: • Crosslinked hydrogel brushes were grafted from SS surfaces for marine antifouling. • All brush-coated SS surfaces could effectively reduce the adhesion of biofouling. • The antifouling efficacy increased with the crosslinking density of hydrogels. - Abstract: Crosslinked hydrogel brushes were grafted from stainless steel (SS) surfaces for marine antifouling. The brushes were prepared by surface-initiated atom transfer radical polymerization (SI-ATRP) of 2-methacryloyloxyethyl phosphorylcholine (MPC) and poly(ethylene glycol) methyl ether methacrylate (PEGMA) respectively with different fractions of crosslinker in the feed. The grafted layers prepared with different thickness were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), ellipsometry and water contact angle measurements. With the increase in the fraction of crosslinker in the feed, the thickness of the grafted layer increased and the surface became smooth. All the brush-coated SS surfaces could effectively reduce the adhesion of bacteria and microalgae and settlement of barnacle cyprids, as compared to the pristine SS surface. The antifouling efficacy of the PEGMA polymer (PPEGMA)-grafted surface was higher than that of the MPC polymer (PMPC)-grafted surfaces. Furthermore, the crosslinked hydrogel brush-grafted surfaces exhibited better fouling resistance than the non-crosslinked polymer brush-grafted surfaces, and the antifouling efficacy increased with the crosslinking density. These hydrogel coatings of low toxicity and excellent anti-adhesive characteristics suggested their useful applications as environmentally friendly antifouling coatings.

Hydrogel brushes grafted from stainless steel via surface-initiated atom transfer radical polymerization for marine antifouling

International Nuclear Information System (INIS)

Wang, Jingjing; Wei, Jun

2016-01-01

Highlights: • Crosslinked hydrogel brushes were grafted from SS surfaces for marine antifouling. • All brush-coated SS surfaces could effectively reduce the adhesion of biofouling. • The antifouling efficacy increased with the crosslinking density of hydrogels. - Abstract: Crosslinked hydrogel brushes were grafted from stainless steel (SS) surfaces for marine antifouling. The brushes were prepared by surface-initiated atom transfer radical polymerization (SI-ATRP) of 2-methacryloyloxyethyl phosphorylcholine (MPC) and poly(ethylene glycol) methyl ether methacrylate (PEGMA) respectively with different fractions of crosslinker in the feed. The grafted layers prepared with different thickness were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), ellipsometry and water contact angle measurements. With the increase in the fraction of crosslinker in the feed, the thickness of the grafted layer increased and the surface became smooth. All the brush-coated SS surfaces could effectively reduce the adhesion of bacteria and microalgae and settlement of barnacle cyprids, as compared to the pristine SS surface. The antifouling efficacy of the PEGMA polymer (PPEGMA)-grafted surface was higher than that of the MPC polymer (PMPC)-grafted surfaces. Furthermore, the crosslinked hydrogel brush-grafted surfaces exhibited better fouling resistance than the non-crosslinked polymer brush-grafted surfaces, and the antifouling efficacy increased with the crosslinking density. These hydrogel coatings of low toxicity and excellent anti-adhesive characteristics suggested their useful applications as environmentally friendly antifouling coatings.

Abrasive wear behaviour of bio-active glass ceramics containing ...

Indian Academy of Sciences (India)

Unknown

Technical Education Faculty, Mersin University, 33480 Tarsus, Turkey. MS received 18 October 2005; revised 22 March 2006. Abstract. In this study, abrasive ... process were used to produce bio-active ceramics. Fracture toughness of studied ...

Surface changes of enamel after brushing with charcoal toothpaste

Science.gov (United States)

Pertiwi, U. I.; Eriwati, Y. K.; Irawan, B.

2017-08-01

The aim of this study was to determine the surface roughness changes of tooth enamel after brushing with charcoal toothpaste. Thirty specimens were brushed using distilled water (the first group), Strong® Formula toothpaste (the second group), and Charcoal® Formula toothpaste for four minutes and 40 seconds (equivalent to one month) and for 14 minutes (equivalent to three months) using a soft fleece toothbrush with a mass of 150 gr. The roughness was measured using a surface roughness tester, and the results were tested with repeated ANOVA test and one-way ANOVA. The value of the surface roughness of tooth enamel was significantly different (penamel.

Fast discharging homopolar drum-type generator with gas bearing and flexible copper-fiber brushes

International Nuclear Information System (INIS)

Kibardin, A.S.; Komin, A.V.; Sojkin, V.F.; Frolkin, V.I.

1984-01-01

The description and results of testing schock-excited homopolar generator (SEHG) with a drum-type rotor, a gas bearing and flexible copper-fiber brushes are presented. SEHG has a magnetic core with two excitation coils with the designed field of 1.8-2 T in the gap. The drum-type titanium rotor has 80 kg, is 0.5 m in diameter, 0.25 m length and 0.05 m thick. SEHG power is 3.6 MJ, overall dimensions are 0.8x1 m. Single- and double-row bearings, representing an aluminium shell of 15 mm thick, established inside an external backward current lead and isolated from it, are used to control serviceability of a radial gas-static bearing, which is a support for an SEHG rotor. The bearing surface was covered with the colloidal graphite and had one or two rows by 24 openings for swelling. Brush units represent a bronze brush ring, containing 44 copper-fiber brushes. Tests results confirm serviceability of copper-fiber brushes with quite large dimensions and permit to count on producing the 2.4 MA electric discharge and 12 ms pulse rise time

New decontamination techniques: chemical gels, electropolishing and abrasives

International Nuclear Information System (INIS)

Brunel, G.; Gauchon, J.P.; Kervegant, Y.; Josso, F.

1991-01-01

The decommissioning of nuclear installations requires decontamination techniques that are efficient, simple to apply and producing a small amount of wastes, which are easy to process. With a view to this, three decontamination methods, which appear to be particularly suited to decommissioning, have been studied. These three methods are: - spraying of gels carrying chemical decontaminating agents, - electropolishing with a swab device, - abrasives blasting. After parametric tests on non-radioactive and active samples, the industrial application of these methods in the dismantling of installations was studied. These industrial applications concern: - decontamination of pieces coming from the German BWR ISAR by immersion and gel spraying, - decontamination, mainly by gel spraying, and dismantling of the BRENNILIS bituminisation plant, - decontamination of part of the cooling circuit of the graphite gas reactor G2 by gel spraying, - decontamination of a component of the FBR SuperPhenix, using dry abrasives blasting. During the first three applications, generated secondary wastes volume and form were determined. 33 tabs., 16 figs., 12 refs

The effect of food location, heat load, and intrusive medical procedures on brushing activity in dairy cows.

Science.gov (United States)

Mandel, R; Whay, H R; Nicol, C J; Klement, E

2013-10-01

Animals allocate time and effort to a range of core (e.g., sleeping, feeding, drinking) and "luxury" (e.g., playing, exploring) activities. A luxury activity is characterized by low resilience and, as such, will be reduced when time or energy resources are limited, including under conditions of stress or discomfort. One seemingly luxurious activity available to cows on an increasing number of dairy farms is rubbing against an automated brush. The current study examined the effect of distance from food, heat load, and an intrusive medical procedure (i.e., artificial insemination and transrectal pregnancy examination) on the resilience of brush usage. The probability of using the brush decreased significantly when food was located distantly from the brush (mean=0.53) compared with days when food was located closer to the brush (mean=0.81). Brush usage also decreased at high temperature and humidity levels, with an average decrease of 0.062 brushing events for an increase of 1 temperature-humidity index unit (95% confidence interval=-0.93-0.030). In addition, a significant reduction of approximately 50% in brushing activity was observed on days of artificial insemination compared with the preceding 3d and the following 3d. These findings show that brush usage is a low resilience activity that reduces under a range of conditions. It may thus have the potential to be used as an indicator of a range of health and welfare problems in cows. Further research should be conducted to assess the sensitivity and specificity of this suggested tool and its possible contribution to the early detection of morbidity. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Tooth brushing among 11- to 15-year-olds in Denmark: combined effect of social class and migration status.

Science.gov (United States)

Bast, L S; Nordahl, H; Christensen, L B; Holstein, B E

2015-03-01

Regular tooth brushing in adolescence predicts stable tooth brushing habits later in life. Differences in tooth brushing habits by ethnic background and socioeconomic position have been suggested. We investigated migration status and social class in relation to infrequent tooth brushing both separately and combined. The study population was 11-15 year-olds chosen from a clustered random sample of schools. Univariate and multivariate logistic regression analyses estimated the separate and combined effects of migration status and social class on less than twice daily tooth brushing. 10,607 respondents: a response rate of 88.3%. Boys of lower social class had higher odds ratio (OR) of infrequent tooth brushing than girls: 1.98 (95% confidence interval 1.62-2.41) vs 1.80 (1.53-2.24). Immigrants and descendants had higher odds compared to adolescents of Danish origin: immigrant boys OR 1.39 (1.05-1.89), girls OR 1.92 (1.47-2.50); descendant boys OR 2.53 (1.97-3.27), girls OR 2.56 (2.02-3.35). Analyses of the combined effect of social class and migration status showed that the social gradient in tooth brushing habits observed among ethnic Danes cannot be found among groups of immigrants and descendants. The study shows that both non-Danish origin and low social class increases the risk of infrequent tooth brushing among school-aged children. The study calls for in depth analyses of the processes which influence young people's tooth brushing habits. Further, there is a need to strengthen the promotion of appropriate tooth brushing habits of minority and low social class youths.

Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

Science.gov (United States)

Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

2017-11-01

The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

Amphiphilic brushes from metallo-supramolecular block copolymers

NARCIS (Netherlands)

Guillet, P.; Fustin, C.A.; Wouters, D.; Höppener, S.; Schubert, U.S.; Gohy, J.M.W.

2009-01-01

A novel strategy to control the formation of amphiphilic brushes from metallo-supramol. block copolymers is described. The investigated copolymer consists of a polystyrene block linked to a poly(ethylene oxide) one via a charged bis-terpyridine ruthenium(ii) complex (PS-[Ru]-PEO). The initial

Interaction between two parallel plates covered with a polyelectrolyte brush layer in an electrolyte solution.

Science.gov (United States)

Ohshima, Hiroyuki

An approximate analytic expression is derived for the interaction energy between two parallel plates covered with a polyelectrolyte brush layer in an electrolyte solution. The interaction energy has three components: electrostatic interaction energy between two brush layers before and after their contact, steric interaction energy between two brush layers after their contact, and the van der Waals interaction energy between the cores of the plates. It is shown that these three components are of the same order of magnitude and contribute equally to the total interaction energy between two polyelectrolyte-coated plates in an electrolyte solution. On the basis of Derjaguin's approximation, an approximate expression for the interaction energy between two spherical particles covered with polyelectrolyte brush layers is also derived.

A theoretical study of colloidal forces near an amphiphilic polymer brush

Science.gov (United States)

Wu, Jianzhong

2011-03-01

Polymer-based ``non-stick'' coatings are promising as the next generation of effective, environmentally-friendly marine antifouling systems that minimize nonspecific adsorption of extracellular polymeric substances (EPS). However, design and development of such systems are impeded by the poor knowledge of polymer-mediated interactions of biomacromolecules with the protected substrate. In this work, a polymer density functional theory (DFT) is used to predict the potential of mean force between spherical biomacromolecules and amphiphilic copolymer brushes within a coarse-grained model that captures essential nonspecific interactions such as the molecular excluded volume effects and the hydrophobic energies. The relevance of theoretical results for practical control of the EPS adsorption is discussed in terms of the efficiency of different brush configurations to prevent biofouling. It is shown that the most effective antifouling surface may be accomplished by using amphiphilic brushes with a long hydrophilic backbone and a hydrophobic end at moderate grafting density.

Topographical anomaly on surfaces created by abrasive waterjet

Czech Academy of Sciences Publication Activity Database

Hloch, S.; Valíček, Jan

2012-01-01

Roč. 59, 5-8 (2012), s. 593-604 ISSN 0268-3768 Institutional research plan: CEZ:AV0Z30860518 Keywords : abrasive waterjet * initial zone * surface topography Subject RIV: JQ - Machines ; Tools Impact factor: 1.205, year: 2012 http://www.springerlink.com/content/5701144k76v02372

The use of abrasive polishing and laser processing for developing polyurethane surfaces for controlling fibroblast cell behaviour

Energy Technology Data Exchange (ETDEWEB)

Irving, Michael; Murphy, Mark F; Lilley, Francis; French, Paul W; Burton, David R [General Engineering Research Institute, Liverpool John Moores University, Liverpool, L3 3AF (United Kingdom); Dixon, Simon [Biomer Technology LTD, 10 Seymour Court, Tudor Road, Manor Park, Runcorn, Cheshire, WA7 1SY (United Kingdom); Sharp, Martin C [General Engineering Research Institute, Liverpool John Moores University, Liverpool, L3 3AF (United Kingdom)

2017-02-01

Studies have shown that surfaces having micro and nano-scale features can be used to control cell behaviours including; cell proliferation, migration and adhesion. The aim of this work was to compare the use of laser processing and abrasive polishing to develop micro/nano-patterned polyurethane substrates for controlling fibroblast cell adhesion, migration and proliferation. Laser processing in a directional manner resulted in polyurethane surfaces having a ploughed field effect with micron-scale features. In contrast, abrasive polishing in a directional and random manner resulted in polyurethane surfaces having sub-micron scale features orientated in a linear or random manner. Results show that when compared with flat (non-patterned) polymer, both the laser processed and abrasive polished surface having randomly organised features, promoted significantly greater cell adhesion, while also enhancing cell proliferation after 72 h. In contrast, the abrasive polished surface having linear features did not enhance cell adhesion or proliferation when compared to the flat surface. For cell migration, the cells growing on the laser processed and abrasively polished random surface showed decreased levels of migration when compared to the flat surface. This study shows that both abrasive polishing and laser processing can be used to produce surfaces having features on the nano-scale and micron-scale, respectively. Surfaces produced using both techniques can be used to promote fibroblast cell adhesion and proliferation. Thus both methods offer a viable alternative to using lithographic techniques for developing patterned surfaces. In particular, abrasive polishing is an attractive method due to it being a simple, rapid and inexpensive method that can be used to produce surfaces having features on a comparable scale to more expensive, multi-step methods. - Highlights: • Abrasive polishing can generate nano-scratches on stainless steel to cast polymer films for cell

The use of abrasive polishing and laser processing for developing polyurethane surfaces for controlling fibroblast cell behaviour

International Nuclear Information System (INIS)

Irving, Michael; Murphy, Mark F; Lilley, Francis; French, Paul W; Burton, David R; Dixon, Simon; Sharp, Martin C

2017-01-01

Studies have shown that surfaces having micro and nano-scale features can be used to control cell behaviours including; cell proliferation, migration and adhesion. The aim of this work was to compare the use of laser processing and abrasive polishing to develop micro/nano-patterned polyurethane substrates for controlling fibroblast cell adhesion, migration and proliferation. Laser processing in a directional manner resulted in polyurethane surfaces having a ploughed field effect with micron-scale features. In contrast, abrasive polishing in a directional and random manner resulted in polyurethane surfaces having sub-micron scale features orientated in a linear or random manner. Results show that when compared with flat (non-patterned) polymer, both the laser processed and abrasive polished surface having randomly organised features, promoted significantly greater cell adhesion, while also enhancing cell proliferation after 72 h. In contrast, the abrasive polished surface having linear features did not enhance cell adhesion or proliferation when compared to the flat surface. For cell migration, the cells growing on the laser processed and abrasively polished random surface showed decreased levels of migration when compared to the flat surface. This study shows that both abrasive polishing and laser processing can be used to produce surfaces having features on the nano-scale and micron-scale, respectively. Surfaces produced using both techniques can be used to promote fibroblast cell adhesion and proliferation. Thus both methods offer a viable alternative to using lithographic techniques for developing patterned surfaces. In particular, abrasive polishing is an attractive method due to it being a simple, rapid and inexpensive method that can be used to produce surfaces having features on a comparable scale to more expensive, multi-step methods. - Highlights: • Abrasive polishing can generate nano-scratches on stainless steel to cast polymer films for cell

The theory of reasoned action in describing tooth brushing, dental caries and diabetes adherence among diabetic patients.

Science.gov (United States)

Syrjälä, Anna-Maija H; Niskanen, Mirka C; Knuuttila, Matti L E

2002-05-01

Preventive oral health behaviour is important among diabetic patients, as it has been found that dental diseases and insulin-dependent diabetes mellitus (IDDM) have some psychological and biological factors in common. The aim here was to analyze the variables of Ajzen and Fishbein's theory of reasoned action to explain the reported frequency of tooth brushing, dental caries, HbA1c level and diabetes adherence. Cross-sectional data were gathered from 149 IDDM patients by means of a quantitative questionnaire, clinical examination and patient records. The results showed that a firmer intention to brush the teeth was related to a higher reported frequency of tooth brushing (p < 0.001). The attitude to and the subjective norm of tooth brushing were related to the intention to brush(p < 0.001) and to the reported frequency of tooth brushing. A better dental attitude was related to better diabetes adherence (p = 0.002) and fewer decayed surfaces (p = 0.01), and a firmer intention to brush the teeth was related to a lower HbA1c level (p = 0.015). Our results suggest that in oral health promotion among diabetic patients, both subjective norm and attitude are important and that diabetes adherence may be influenced by promoting dental attitude.

Endocytic trafficking from the small intestinal brush border probed with FM dye

DEFF Research Database (Denmark)

Hansen, Gert H; Rasmussen, Karina; Niels-Christiansen, Lise-Lotte

2009-01-01

-linking galectins/intelectin, but little is known about the dynamic properties of this highly specialized membrane. Here, we probed the endocytic membrane trafficking from the brush border of organ cultured pig intestinal mucosal explants by use of a fixable, lipophilic FM dye. The fluorescent dye readily......, contributes to the overall permeability barrier of the gut. Key words: FM dye, small intestine, brush border, endocytosis....

Cigarette smoking, tooth brushing characteristics, and perceived ...

African Journals Online (AJOL)

This study was conducted among four hundred non-dental undergraduates of University of Benin, Benin City, Nigeria to assess the prevalence of cigarette smoking, tooth brushing characteristics, perceived efficacy in oral self-care and preventing gingivodental diseases among them. The result showed that the perceived ...

Drilling Deeper into tooth brushing skills: Is proactive interference an under-recognized factor in oral hygiene behavior change?

Science.gov (United States)

Thavarajah, Rooban; Kumar, Madan; Mohandoss, Anusa Arunachalam; Vernon, Lance T

2015-09-01

Proper tooth brushing is a seemingly simple motor activity that can promote oral health. Applying health theories, such as the Information-Motivation-Behavioral Skills (IMB) model, Motivational Interviewing (MI) and Integrated Health Coaching (IHC), may help optimize tooth brushing technique in those with suboptimal skills. Some motor activities, including tooth brushing, may over time become rote and unconscious actions, such that an existing habit can inhibit new learning, i.e., exert proactive interference on learning the new skill. Proactive interference may impede the acquisition of new tooth brushing skills; thus, in this report, we: (1) Review how the habit of tooth brushing is formed; (2) Postulate how proactive interference could impede the establishment of proper tooth brushing retraining; (3) Discuss the merits of this hypothesis; and (4) Provide guidance for future work in this topic within the context of an approach to behavior change that integrates IMB, MI and IHC methodology.

A test for Creutzfeldt-Jakob disease using nasal brushings.

Science.gov (United States)

Orrú, Christina D; Bongianni, Matilde; Tonoli, Giovanni; Ferrari, Sergio; Hughson, Andrew G; Groveman, Bradley R; Fiorini, Michele; Pocchiari, Maurizio; Monaco, Salvatore; Caughey, Byron; Zanusso, Gianluigi

2014-08-07

Definite diagnosis of sporadic Creutzfeldt-Jakob disease in living patients remains a challenge. A test that detects the specific marker for Creutzfeldt-Jakob disease, the prion protein (PrP(CJD)), by means of real-time quaking-induced conversion (RT-QuIC) testing of cerebrospinal fluid has a sensitivity of 80 to 90% for the diagnosis of sporadic Creutzfeldt-Jakob disease. We have assessed the accuracy of RT-QuIC analysis of nasal brushings from olfactory epithelium in diagnosing sporadic Creutzfeldt-Jakob disease in living patients. We collected olfactory epithelium brushings and cerebrospinal fluid samples from patients with and patients without sporadic Creutzfeldt-Jakob disease and tested them using RT-QuIC, an ultrasensitive, multiwell plate-based fluorescence assay involving PrP(CJD)-seeded polymerization of recombinant PrP into amyloid fibrils. The RT-QuIC assays seeded with nasal brushings were positive in 30 of 31 patients with Creutzfeldt-Jakob disease (15 of 15 with definite sporadic Creutzfeldt-Jakob disease, 13 of 14 with probable sporadic Creutzfeldt-Jakob disease, and 2 of 2 with inherited Creutzfeldt-Jakob disease) but were negative in 43 of 43 patients without Creutzfeldt-Jakob disease, indicating a sensitivity of 97% (95% confidence interval [CI], 82 to 100) and specificity of 100% (95% CI, 90 to 100) for the detection of Creutzfeldt-Jakob disease. By comparison, testing of cerebrospinal fluid samples from the same group of patients had a sensitivity of 77% (95% CI, 57 to 89) and a specificity of 100% (95% CI, 90 to 100). Nasal brushings elicited stronger and faster RT-QuIC responses than cerebrospinal fluid (PCreutzfeldt-Jakob disease and indicated substantial prion seeding activity lining the nasal vault. (Funded by the Intramural Research Program of the National Institute of Allergy and Infectious Diseases and others.).

A Test for Creutzfeldt–Jakob Disease Using Nasal Brushings

Science.gov (United States)

Orrú, Christina D.; Bongianni, Matilde; Tonoli, Giovanni; Ferrari, Sergio; Hughson, Andrew G.; Groveman, Bradley R.; Fiorini, Michele; Pocchiari, Maurizio; Monaco, Salvatore; Caughey, Byron; Zanusso, Gianluigi

2014-01-01

BACKGROUND Definite diagnosis of sporadic Creutzfeldt–Jakob disease in living patients remains a challenge. A test that detects the specific marker for Creutzfeldt–Jakob disease, the prion protein (PrPCJD), by means of real-time quaking-induced conversion (RT-QuIC) testing of cerebrospinal fluid has a sensitivity of 80 to 90% for the diagnosis of sporadic Creutzfeldt–Jakob disease. We have assessed the accuracy of RT-QuIC analysis of nasal brushings from olfactory epithelium in diagnosing sporadic Creutzfeldt– Jakob disease in living patients. METHODS We collected olfactory epithelium brushings and cerebrospinal fluid samples from patients with and patients without sporadic Creutzfeldt–Jakob disease and tested them using RT-QuIC, an ultrasensitive, multiwell plate–based fluorescence assay involving PrPCJD-seeded polymerization of recombinant PrP into amyloid fibrils. RESULTS The RT-QuIC assays seeded with nasal brushings were positive in 30 of 31 patients with Creutzfeldt–Jakob disease (15 of 15 with definite sporadic Creutzfeldt–Jakob disease, 13 of 14 with probable sporadic Creutzfeldt–Jakob disease, and 2 of 2 with inherited Creutzfeldt–Jakob disease) but were negative in 43 of 43 patients without Creutzfeldt–Jakob disease, indicating a sensitivity of 97% (95% confidence interval [CI], 82 to 100) and specificity of 100% (95% CI, 90 to 100) for the detection of Creutzfeldt–Jakob disease. By comparison, testing of cerebrospinal fluid samples from the same group of patients had a sensitivity of 77% (95% CI, 57 to 89) and a specificity of 100% (95% CI, 90 to 100). Nasal brushings elicited stronger and faster RT-QuIC responses than cerebrospinal fluid (PCreutzfeldt–Jakob disease and indicated substantial prion seeding activity lining the nasal vault. (Funded by the Intramural Research Program of the National Institute of Allergy and Infectious Diseases and others.) PMID:25099576

Evaluation of a parent-designed programme to support tooth brushing of infants and young children*

Science.gov (United States)

Huebner, CE; Milgrom, P

2015-01-01

Objectives This study developed and tested an intervention to help parents establish a routine of brushing their young children’s teeth twice a day. Methods Community-based participatory research methods were used to engage parents in the design of the intervention to maximize its relevance and acceptability to others. Input was obtained by interviews and focus groups. The resulting intervention was four 90-min small-group sessions that provided educational information, direct instruction, practice and peer-to-peer problem-solving. A pre- to post-non-randomized design was used to evaluate the intervention’s effect to increase or maintain parents’ twice daily brushing. Results Intervention participants were 67 primary caregivers of children under six years of age. Of the 67 initial participants, 50 completed a post-intervention questionnaire administered 4 to 8 weeks following the intervention. The proportion of parents who reported brushing their young children’s teeth twice a day increased significantly from 59 per cent prior to the intervention to 89 per cent post-intervention (McNemar’s X2 = 10.71, P = 0.002). There were concomitant and statistically significant increases over the study period in parents’ confidence for brushing twice a day, attitudes about the importance of brushing and their self-efficacy for tooth brushing. Parents’ knowledge of children’s oral health, assessed by a 15-item scale developed for this study (‘Things to Know About Baby Teeth’), also increased significantly. Conclusions Twice daily tooth brushing is a low-cost, effective strategy to reduce the risk of childhood caries. As demonstrated here, community-based efforts can help parents achieve this important health behaviour. PMID:25070036

Multilayer affinity adsorption of albumin on polymer brushes modified membranes in a continuous-flow system.

Science.gov (United States)

Hu, Meng-Xin; Li, Xiang; Li, Ji-Nian; Huang, Jing-Jing; Ren, Ge-Rui

2018-02-23

Polymer brushes modified surfaces have been widely used for protein immobilization and isolation. Modification of membranes with polymer brushes increases the surface concentration of affinity ligands used for protein binding. Albumin is one of the transporting proteins and shows a high affinity to bile acids. In this work, the modified membranes with cholic acid-containing polymer brushes can be facilely prepared by the immobilization of cholic acid on the poly(2-hydroxyethyl methacrylate) grafted microporous polypropylene membranes (MPPMs) for affinity adsorption of albumin. ATR/FT-IR and X-ray photoelectron spectroscopy were used to characterize the chemical composition of the modified membranes. Water contact angle measurements were used to analyze the hydrophilic/hydrophobic properties of the membrane surface. The modified MPPMs show a high affinity to albumin and have little non-specific adsorption of hemoglobin. The dynamic binding capacity of albumin in the continous-flow system increases with the cycle number and feed rate as the binding degree of cholic acid is moderate. The highest binding capacity of affinity membranes is about 52.49 g/m 2 membrane, which is about 24 times more than the monolayer binding capacity. These results reveal proteins could be captured in multilayers by the polymer brushes containing affinity ligands similar to the polymer brushes containing ion-exchange groups, which open up the potential of the polymer brushes containing affinity ligands in protein or another components separation. And the cholic acid containing polymer brushes modified membranes has the promising potential for albumin separation and purification rapidly from serum or fermented solution in medical diagnosis and bioseparation. Copyright © 2018 Elsevier B.V. All rights reserved.

Evaluation of a parent-designed programme to support tooth brushing of infants and young children.

Science.gov (United States)

Huebner, C E; Milgrom, P

2015-02-01

This study developed and tested an intervention to help parents establish a routine of brushing their young children's teeth twice a day. Community-based participatory research methods were used to engage parents in the design of the intervention to maximize its relevance and acceptability to others. Input was obtained by interviews and focus groups. The resulting intervention was four 90-min small-group sessions that provided educational information, direct instruction, practice and peer-to-peer problem-solving. A pre- to post-non-randomized design was used to evaluate the intervention's effect to increase or maintain parents' twice daily brushing. Intervention participants were 67 primary caregivers of children under six years of age. Of the 67 initial participants, 50 completed a post-intervention questionnaire administered 4 to 8 weeks following the intervention. The proportion of parents who reported brushing their young children's teeth twice a day increased significantly from 59 per cent prior to the intervention to 89 per cent post-intervention (McNemar's X(2)  = 10.71, P = 0.002). There were concomitant and statistically significant increases over the study period in parents' confidence for brushing twice a day, attitudes about the importance of brushing and their self-efficacy for tooth brushing. Parents' knowledge of children's oral health, assessed by a 15-item scale developed for this study ('Things to Know About Baby Teeth'), also increased significantly. Twice daily tooth brushing is a low-cost, effective strategy to reduce the risk of childhood caries. As demonstrated here, community-based efforts can help parents achieve this important health behaviour. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Dual brush process for selective surface modification in graphoepitaxy directed self-assembly

Science.gov (United States)

Doise, Jan; Chan, Boon Teik; Hori, Masafumi; Gronheid, Roel

2017-07-01

Graphoepitaxy directed self-assembly is a potential low-cost solution for patterning via layers with pitches beyond the reach of a single optical lithographic exposure. In this process, selective control of the interfacial energy at the bottom and sidewall of the template is an important but challenging exercise. A dual brush process is implemented, in which two brushes with distinct end-groups are consecutively grafted to the prepattern to achieve fully independent modification of the bottom and sidewall surface of the template. A comprehensive study of hole pattern quality shows that using a dual brush process leads to a substantial improvement in terms of positional and dimensional variability across the process window. These findings will be useful to others who wish to manipulate polymer-surface interactions in directed self-assembly flows.

Abrasion Resistance of Nano Silica Modified Roller Compacted Rubbercrete: Cantabro Loss Method and Response Surface Methodology Approach

Science.gov (United States)

Adamu, Musa; Mohammed, Bashar S.; Shafiq, Nasir

2018-04-01

Roller compacted concrete (RCC) when used for pavement is subjected to skidding/rubbing by wheels of moving vehicles, this causes pavement surface to wear out and abrade. Therefore, abrasion resistance is one of the most important properties of concern for RCC pavement. In this study, response surface methodology was used to design, evaluate and analyze the effect of partial replacement of fine aggregate with crumb rubber, and addition of nano silica on the abrasion resistance of roller compacted rubbercrete (RCR). RCR is the terminology used for RCC pavement where crumb rubber was used as partial replacement to fine aggregate. The Box-Behnken design method was used to develop the mixtures combinations using 10%, 20%, and 30% crumb rubber with 0%, 1%, and 2% nano silica. The Cantabro loss method was used to measure the abrasion resistance. The results showed that the abrasion resistance of RCR decreases with increase in crumb rubber content, and increases with increase in addition of nano silica. The analysis of variance shows that the model developed using response surface methodology (RSM) has a very good degree of correlation, and can be used to predict the abrasion resistance of RCR with a percentage error of 5.44%. The combination of 10.76% crumb rubber and 1.59% nano silica yielded the best combinations of RCR in terms of abrasion resistance of RCR.

Hierarchical antifouling brushes for biosensing applications

Czech Academy of Sciences Publication Activity Database

de los Santos Pereira, Andres; Riedel, Tomáš; Brynda, Eduard; Rodriguez-Emmenegger, Cesar

2014-01-01

Roč. 202, 31 October (2014), s. 1313-1321 ISSN 0925-4005 R&D Projects: GA ČR GAP205/12/1702; GA MŠk(CZ) EE2.3.30.0029; GA MŠk(CZ) ED1.1.00/02.0109 Institutional support: RVO:61389013 Keywords : hierarchically structured brushes * affinity biosensors * fouling Subject RIV: CE - Biochemistry Impact factor: 4.097, year: 2014

Gallium-containing polymer brush film as efficient supported Lewis acid catalyst in a glass microreactor

Directory of Open Access Journals (Sweden)

Rajesh Munirathinam

2013-08-01

Full Text Available Polystyrene sulfonate polymer brushes, grown on the interior of the microchannels in a microreactor, have been used for the anchoring of gallium as a Lewis acid catalyst. Initially, gallium-containing polymer brushes were grown on a flat silicon oxide surface and were characterized by FTIR, ellipsometry, and X-ray photoelectron spectroscopy (XPS. XPS revealed the presence of one gallium per 2–3 styrene sulfonate groups of the polymer brushes. The catalytic activity of the Lewis acid-functionalized brushes in a microreactor was demonstrated for the dehydration of oximes, using cinnamaldehyde oxime as a model substrate, and for the formation of oxazoles by ring closure of ortho-hydroxy oximes. The catalytic activity of the microreactor could be maintained by periodic reactivation by treatment with GaCl3.

Synthesis of thermoresponsive poly(N-isopropylacrylamide) brush on silicon wafer surface via atom transfer radical polymerization

Energy Technology Data Exchange (ETDEWEB)

Turan, Eylem; Demirci, Serkan [Department of Chemistry, Faculty of Art and Science, Gazi University, 06500 Besevler, Ankara (Turkey); Caykara, Tuncer, E-mail: caykara@gazi.edu.t [Department of Chemistry, Faculty of Art and Science, Gazi University, 06500 Besevler, Ankara (Turkey)

2010-08-31

Thermoresponsive poly(N-isopropylacrylamide) [poly(NIPAM)] brush on silicon wafer surface was prepared by combining the self-assembled monolayer of initiator and atom transfer radical polymerization (ATRP). The resulting polymer brush was characterized by in situ reflectance Fourier transform infrared spectroscopy, atomic force microscopy and ellipsometry techniques. Gel permeation chromatography determination of the number-average molecular weight and polydispersity index of the brush detached from the silicon wafer surface suggested that the surface-initiated ATRP method can provide relatively homogeneous polymer brush. Contact angle measurements exhibited a two-stage increase upon heating over the board temperature range 25-45 {sup o}C, which is in contrast to the fact that free poly(NIPAM) homopolymer in aqueous solution exhibits a phase transition at ca. 34 {sup o}C within a narrow temperature range. The first de-wetting transition takes place at 27 {sup o}C, which can be tentatively attributed to the n-cluster induced collapse of the inner region of poly(NIPAM) brush close to the silicon surface; the second de-wetting transition occurs at 38 {sup o}C, which can be attributed to the outer region of poly(NIPAM) brush, possessing much lower chain density compared to that of the inner part.

The association between parents' perceived social norms for toothbrushing and the frequency with which they report brushing their child's teeth.

Science.gov (United States)

Trubey, R J; Moore, S C; Chestnutt, I G

2015-06-01

To determine whether parents' judgements on how often other parents brush their children's teeth are associated with the frequency with which they brush their own children's teeth, and their satisfaction with their child's brushing routine. A cross-sectional questionnaire survey completed by 297 parents of children aged 3-6. Parents were asked how often they brushed their own child's teeth per week, how often they thought other parents did so, and how satisfied they were with their child's toothbrushing routine. Demographic data were also collected. The mean frequency that parents brushed their children's teeth was 12.5 times per week. Multiple regression analysis tested the relationship between parents' perceptions of other parents brushing frequency (mean 10.5 times per week) and how often they brushed their own child's teeth, controlling for socio-demographic factors, and yielded a positive association (p parents' satisfaction with their child's brushing routine and the extent to which they thought it was better than that of the average child (p Parents' judgements on how frequently other parents brush their children's teeth are associated with their own behaviour and satisfaction. Re-framing oral health messages to include some form of social normative information ("most parents do this") may prove more persuasive than simple prescriptive advice ("you should do this").

29 CFR 1926.303 - Abrasive wheels and tools.

Science.gov (United States)

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Abrasive wheels and tools. 1926.303 Section 1926.303 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... freely on the spindle and shall not be forced on. The spindle nut shall be tightened only enough to hold...

Thermodynamics, electrostatics, and ionic current in nanochannels grafted with pH-responsive end-charged polyelectrolyte brushes.

Science.gov (United States)

Chen, Guang; Das, Siddhartha

2017-03-01

In this paper, we study the thermodynamics, electrostatics, and an external electric field driven ionic current in a pH-responsive, end-charged polyelectrolyte (PE) brush grafted nanochannel. By employing a mean field theory, we unravel a highly nonintuitive interplay of pH and electrolyte salt concentration in dictating the height of the end-charged PE brush. Larger pH or weak hydrogen ion concentration leads to maximum ionization of the charge-producing group-as a consequence, the resulting the electric double layer (EDL) energy get maximized causing a maximum deviation of the brush height from the value (d 0 ) of the uncharged brush. This deviation may result in enhancement or lowering of the brush height as compared to d 0 depending on whether the PE end locates lower or higher than h/2 (h is the nanochannel half height) and the salt concentration. Subsequently, we use this combined PE-brush-configuration-EDL-electrostatics framework to compute the ionic current in the nanochannel. We witness that the ionic current for smaller pH is much larger despite the corresponding magnitude of the EDL electrostatic potential being much smaller-this stems from the presence of a much larger concentration of H+ ions at small pH and the fact that H+ ions have very large mobilities. In fact, this ionic current shows a steep variation with pH that can be useful in exploring new designs for applications involving quantification and characterization of ionic current in PE-brush-grafted nanochannels. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Numerical study of agglomerate abrasion in a tumbling mixer

NARCIS (Netherlands)

Thanh Nguyen, [No Value; Willemsz, Tofan; Frijlink, Henderik; Maarschalk, Kees van der Voort

2014-01-01

A numerical simulation using the Discrete Element Method (DEM) was performed to investigate the phenomena concerning the abrasion and breakage of agglomerates in a diffusion powder mixer. Agglomerates were created by defining a single structure of particles with bonds of different strengths using

Release of particles by abrasion of CNT composites using a belt sander

International Nuclear Information System (INIS)