Inhibition of Copper Pitting Corrosion in Aggressive Potable Waters

Directory of Open Access Journals (Sweden)

Emily Sarver

2012-01-01

Full Text Available Copper pitting corrosion can lead to premature plumbing failures, and can be caused by aggressive potable waters characterized by high pH, free chlorine residual and low alkalinity. In such waters and under continuous flow, certain inhibitors including phosphate, silica or natural organic matter may greatly reduce pitting occurrence. In the current work, 1 mg/L phosphate (as P completely prevented initiation of pits, and 5 mg/L silica (as Si significantly decelerated pitting. However, much lower doses of these inhibitors had little benefit and actually accelerated the rate of attack in some cases. Effects of organic matter were dependent on both the type (e.g., natural versus ozonated humic substances and dosage. Dose-response effects of free chlorine and alkalinity were also investigated. Based on electrochemical data, pits initiated more rapidly with increased free chlorine, but even moderate levels of chlorine (~0.4 mg/L eventually caused severe pitting. High alkalinity decreased pit propagation rates but did not prevent pit formation.

Trace metal depositional patterns from an open pit mining activity as revealed by archived avian gizzard contents

Energy Technology Data Exchange (ETDEWEB)

Bendell, L.I., E-mail: bendell@sfu.ca

2011-02-15

Archived samples of blue grouse (Dendragapus obscurus) gizzard contents, inclusive of grit, collected yearly between 1959 and 1970 were analyzed for cadmium, lead, zinc, and copper content. Approximately halfway through the 12-year sampling period, an open-pit copper mine began activities, then ceased operations 2 years later. Thus the archived samples provided a unique opportunity to determine if avian gizzard contents, inclusive of grit, could reveal patterns in the anthropogenic deposition of trace metals associated with mining activities. Gizzard concentrations of cadmium and copper strongly coincided with the onset of opening and the closing of the pit mining activity. Gizzard zinc and lead demonstrated significant among year variation; however, maximum concentrations did not correlate to mining activity. The archived gizzard contents did provide a useful tool for documenting trends in metal depositional patterns related to an anthropogenic activity. Further, blue grouse ingesting grit particles during the time of active mining activity would have been exposed to toxicologically significant levels of cadmium. Gizzard lead concentrations were also of toxicological significance but not related to mining activity. This type of 'pulse' toxic metal exposure as a consequence of open-pit mining activity would not necessarily have been revealed through a 'snap-shot' of soil, plant or avian tissue trace metal analysis post-mining activity. - Research Highlights: {yields} Archived gizzard samples reveals mining history. {yields} Grit ingestion exposes grouse to cadmium and lead. {yields} Grit selection includes particles enriched in cadmium. {yields} Cadmium enriched particles are of toxicological significance.

THE IMPACT OF PHOSPHATE ON COPPER PITTING CORROSION

Science.gov (United States)

Pinhole leaks caused by extensive localized or pitting corrosion of copper pipes is a problem for many homeowners. Pinhole water leaks may result in water damage, mold growth, and costly repairs. A large water system in Florida has been addressing a widespread pinhole leak proble...

Some questions on small uranium open-pit mines

International Nuclear Information System (INIS)

Li Junyi

1992-01-01

The experiences of the existing uranium open pits are summarized and the questions in design, erection and production are analyzed. It is important helpful to develop and to design such economical and reasonable small uranium open pits

The potential use of exhausted open pit mine voids as sinks for atmospheric CO2: insights from natural reedbeds and mine water treatment wetlands

OpenAIRE

Younger, Paul L.; Mayes, William M.

2015-01-01

Abandoned surface mine voids are often left to flood, forming pit lakes. Drawing simple but important lessons from experiences with compost-based passive remediation systems for acidic mine waters, an alternative end-use for open pit mine voids is proposed: gradual infilling with organic material, which can serve as a long-term sink for atmospheric CO2, whilst ameliorating or eventually eliminating sustained evaporative water loss and acidic water pollution. Key to the success of this approac...

COPPER PITTING CORROSION AND PINHOLE LEAKS: A CASE STUDY

Science.gov (United States)

Localized corrosion, or "pitting", of copper drinking water pipe continues is a problem for many water utilities and their customers. Extreme attack leads to pinhole leaks that can potentially lead to water damage, mold growth, and costly repairs for the homeowners, as well as th...

Pitting corrosion of copper in aqueous solutions containing phosphonic acid as an inhibitor. Hosuhon san wo inhibita toshite fukumu suiyoekichu ni okeru do no koshiku ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Yamada, Y. (Muroran Univ., Hokkaido (Japan). Graduate School); Seri, O.; Tagashira, K. (Muroran Univ., Hokkaido (Japan)); Nagata, K. (Sumitomo Light Metal Co. Ltd., Tokyo (Japan). Technical Research Lab.)

1993-09-15

Phosphonic acid-based inhibitors that are poured into cooling water for copper-tube circulation systems for open heat-accumulators were studied on their influence on pitting corrosion of copper. Amino trimethylene phosphonic acid (ATMP) dissolved into distilled water to 50 ppm was used for the immersion corrosion test. The corrosion-proof effect of additives such as ZnSO4, benzotriazole (BTA) was tested too. 0.5 mm thick phosphate-treated copper plates with a hole of 5 mm in diameter were used as test specimens. Pitting corrosion on the copper plate occurred when ATMP, BTA and ZnSO4 coexisted. It was proved that SO4 [sup 2-] is essential since Na2SO4 in stead of ZnSO4 induced also corrosion. The pitting took place when 0.6 ppm or more of SO4 [sup 2-] was present in a BTA-added ATMP solution. It was observed that the pitting is prone to occur with increase of SO4 [sup 2-] and the number of pitting increases. The following relationship is established when pitting corrosion occurs; E[sub b] [le] E[sub corr], where the former is a potential value at which current density shows a steep increase and the latter is an average value of spontaneous electrode potential showing a plateau. 8 refs., 11 figs., 1 tab.

The planning and operation of open-pit and strip mines: proceedings of an international conference held at the University of Pretoria, 9-13 April 1984

International Nuclear Information System (INIS)

Deetlefs, J.P.

1986-01-01

This book records the proceedings of the second international conference on the theme of planning and operation of open-pit and strip mines. The conference was held in Pretoria during April 1984. The major portion of South African iron ore and copper is mined in open-pit mines. The rapid expansion of the open-pit and strip mining industry has led to the thriving industry of today. Notable areas of growth have been the introduction of capital-intensive machinery such as walking drag-lines, large capacity shovels, in-pit crushers, extensive use of conveyor belts, large haul tracks and ore-dressing plants. Among other areas where corresponding progress has been made are blasting techniques, maintenance planning, computer applications, and large-scale stock-piling of bulk materials. The conference touched on all these subjects under four main headings: mine planning, mining operations, equipment selection and maintenance, and new developments. One paper looks at open-pit production control at Rossing Uranium Limited

5G in Open-Pit Mines

DEFF Research Database (Denmark)

Portela Lopes de Almeida, Erika; Caldwell, George; Rodriguez Larrad, Ignacio

2017-01-01

5G will play a pivotal role in the digitization of the industrial sector and is expected to make the best use of every bit of spectrum available. In this light, this paper presents the results of an extensive measurement campaign in two iron-ore open-pit mining complexes, at the 700 MHz and 2.6 GHz...... for the future wireless network design, simulation and performance evaluation. The results show that, in order to comply with ultra-reliable communications (URC) availability requirements, larger shadowing margins will have to be considered in the network planning in open-pit mines, when compared to traditional...

Effects of selected water chemistry variables on copper pitting propagation in potable water

International Nuclear Information System (INIS)

Ha Hung; Taxen, Claes; Williams, Keith; Scully, John

2011-01-01

Highlights: → The effects of water composition on pit propagation kinetics on Cu were separated from pit initiation and stabilization using the artificial pit method in a range of dilute HCO 3 - , SO 4 2- and Cl - -containing waters. → The effective polarization and Ohmic resistance of pits were lower in SO4 2- -containing solutions and greater in Cl - -containing solutions. → Relationship between the solution composition and the corrosion product identity and morphology were found. → These, in turn controlled the corrosion product Ohmic resistance and subsequently the pit growth rate. - Abstract: The pit propagation behavior of copper (UNS C11000) was investigated from an electrochemical perspective using the artificial pit method. Pit growth was studied systematically in a range of HCO 3 - , SO 4 2- and Cl - containing-waters at various concentrations. Pit propagation was mediated by the nature of the corrosion products formed both inside and over the pit mouth (i.e., cap). Certain water chemistry concentrations such as those high in sulfate were found to promote fast pitting that could be sustained over long times at a fixed applied potential but gradually stifled in all but the lowest concentration solutions. In contrast, Cl - containing waters without sulfate ions resulted in slower pit growth and eventual repassivation. These observations were interpreted through understanding of the identity, amount and porosity of corrosion products formed inside and over pits. These factors controlled their resistive nature as characterized using electrochemical impedance spectroscopy. A finite element model (FEM) was developed which included copper oxidation kinetics, transport by migration and diffusion, Cu(I) and Cu(II) solid corrosion product formation and porosity governed by equilibrium thermodynamics and a saturation index, as well as pit current and depth of penetration. The findings of the modeling were in good agreement with artificial pit experiments

Open pit mining of uranium

International Nuclear Information System (INIS)

Wood, J.T.

1977-01-01

The Jackpile--Paquate Mines of the Anaconda Company are on the Laguna Indian Reservation midway between Grants and Albuquerque, New Mexico. The open pit mining of uranium ore at those mines is conducted in three separate operations (stripping, mining, and ore haul)

Ecological geology environmental assessment of open-pit mines

International Nuclear Information System (INIS)

Dong Shuangfa; Jiang Xue

2010-01-01

In this paper, there is a detail description of ecological geology environmental assessment of open-pit mines, including method, process and results. We took ecological geology environmental assessment work on the base of the results of some open-pit mines such as extremely low content magnetite in Hebei Province, inducted and summarized the ecological geology environment quality. The results are reasonable. It provides basic data for the second mines programming in Hebei Province. (authors)

Stochastic production phase design for an open pit mining complex with multiple processing streams

Science.gov (United States)

Asad, Mohammad Waqar Ali; Dimitrakopoulos, Roussos; van Eldert, Jeroen

2014-08-01

In a mining complex, the mine is a source of supply of valuable material (ore) to a number of processes that convert the raw ore to a saleable product or a metal concentrate for production of the refined metal. In this context, expected variation in metal content throughout the extent of the orebody defines the inherent uncertainty in the supply of ore, which impacts the subsequent ore and metal production targets. Traditional optimization methods for designing production phases and ultimate pit limit of an open pit mine not only ignore the uncertainty in metal content, but, in addition, commonly assume that the mine delivers ore to a single processing facility. A stochastic network flow approach is proposed that jointly integrates uncertainty in supply of ore and multiple ore destinations into the development of production phase design and ultimate pit limit. An application at a copper mine demonstrates the intricacies of the new approach. The case study shows a 14% higher discounted cash flow when compared to the traditional approach.

A New Methodology for Open Pit Slope Design in Karst-Prone Ground Conditions Based on Integrated Stochastic-Limit Equilibrium Analysis

Science.gov (United States)

Zhang, Ke; Cao, Ping; Ma, Guowei; Fan, Wenchen; Meng, Jingjing; Li, Kaihui

2016-07-01

Using the Chengmenshan Copper Mine as a case study, a new methodology for open pit slope design in karst-prone ground conditions is presented based on integrated stochastic-limit equilibrium analysis. The numerical modeling and optimization design procedure contain a collection of drill core data, karst cave stochastic model generation, SLIDE simulation and bisection method optimization. Borehole investigations are performed, and the statistical result shows that the length of the karst cave fits a negative exponential distribution model, but the length of carbonatite does not exactly follow any standard distribution. The inverse transform method and acceptance-rejection method are used to reproduce the length of the karst cave and carbonatite, respectively. A code for karst cave stochastic model generation, named KCSMG, is developed. The stability of the rock slope with the karst cave stochastic model is analyzed by combining the KCSMG code and the SLIDE program. This approach is then applied to study the effect of the karst cave on the stability of the open pit slope, and a procedure to optimize the open pit slope angle is presented.

Situation and development of uranium open-pit mining techniques in China

International Nuclear Information System (INIS)

Li Kaiwen.

1986-01-01

The situation of uranium open-pit mining techniques in China is described. The main experiences in production and management are introduced. Meanwhile the suggestions about the further development of uranium open-pit mining techniques are also proposed

Preliminary study of realizability of Karazhyra open pit coal fines briquetting

International Nuclear Information System (INIS)

Deryavko, I.I.; Perepelkin, I.G.; Chuprunov, K.V.

2001-01-01

Main properties of brown coals in Karazhyra open pit upper and lower packs are determined. Characteristics of these coals briquette-ability are evaluated. A conceptual possibility to obtain high-quality briquettes from open pit coal fines is shown. (author)

PREVENTION OF ACID MINE DRAINAGE GENERATION FROM OPEN-PIT MINE HIGHWALLS

Science.gov (United States)

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Available information on the generation of AMD from open-pit mine highwalls is very limit...

Optimal grade control sampling practice in open-pit mining

DEFF Research Database (Denmark)

Engström, Karin; Esbensen, Kim Harry

2017-01-01

Misclassification of ore grades results in lost revenues, and the need for representative sampling procedures in open pit mining is increasingly important in all mining industries. This study evaluated possible improvements in sampling representativity with the use of Reverse Circulation (RC) drill...... sampling compared to manual Blast Hole (BH) sampling in the Leveäniemi open pit mine, northern Sweden. The variographic experiment results showed that sampling variability was lower for RC than for BH sampling. However, the total costs for RC drill sampling are significantly exceeding current costs...... for manual BH sampling, which needs to be compensated for by other benefits to motivate introduction of RC drilling. The main conclusion is that manual BH sampling can be fit-for-purpose in the studied open pit mine. However, with so many mineral commodities and mining methods in use globally...

Standardized emissions inventory methodology for open-pit mining areas.

Science.gov (United States)

Huertas, Jose I; Camacho, Dumar A; Huertas, Maria E

2011-08-01

There is still interest in a unified methodology to quantify the mass of particulate material emitted into the atmosphere by activities inherent to open-pit mining. For the case of total suspended particles (TSP), the current practice is to estimate such emissions by developing inventories based on the emission factors recommended by the USEPA for this purpose. However, there are disputes over the specific emission factors that must be used for each activity and the applicability of such factors to cases quite different to the ones under which they were obtained. There is also a need for particulate matter with an aerodynamic diameter less than 10 μm (PM(10)) emission inventories and for metrics to evaluate the emission control programs implemented by open-pit mines. To address these needs, work was carried out to establish a standardized TSP and PM(10) emission inventory methodology for open-pit mining areas. The proposed methodology was applied to seven of the eight mining companies operating in the northern part of Colombia, home to the one of the world's largest open-pit coal mining operations (∼70 Mt/year). The results obtained show that transport on unpaved roads is the mining activity that generates most of the emissions and that the total emissions may be reduced up to 72% by spraying water on the unpaved roads. Performance metrics were defined for the emission control programs implemented by mining companies. It was found that coal open-pit mines are emitting 0.726 and 0.180 kg of TSP and PM(10), respectively, per ton of coal produced. It was also found that these mines are using on average 1.148 m(2) of land per ton of coal produced per year.

78 FR 33894 - Proposed Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-06-05

... chemicals and fumes caused by open burn pits. DATES: Written comments and recommendations on the proposed... to ``OMB Control No. 2900-NEW, Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire.... Title: Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire, VA Form 10-10066. OMB...

Application of Surpac and Whittle Software in Open Pit Optimisation ...

African Journals Online (AJOL)

Application of Surpac and Whittle Software in Open Pit Optimisation and Design. ... This paper studies the Surpac and Whittle software and their application in designing an optimised pit. ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

A method for opening a mine field which is adjacent to a pit

Energy Technology Data Exchange (ETDEWEB)

Onishchenko, V.I.; Grebenyuk, V.K.; Kukharev, V.N.; Martynenko, V.P.; Omelnitskiy, A.G.; Sallin, V.I.; Sidorov, A.S.

1982-01-01

The method for opening a mine field adjacent to a pit includes the construction of the main and auxiliary opening drifts in the pit and the surface complex of the mine through assembling a support with subsequent filling of them by tailings of the covering rock. In order to increase the productive capacity of the mine, to reduce capital expenditures and to increase the safety of underground operations, a base is first formed from the tailing rock along the front of the open mining operations, from the bottom of the pit at the level of the stratum being opened to the surface with simultaneous layer by layer packing of the cited base, after which the opening drifts are built on this base. The mouth of the main opening drifts and the surface complex of the mine are positioned in the region of the pit.

Pitting Corrosion of Copper in Waters with High pH and Low Alkalinity

Science.gov (United States)

Localized or pitting corrosion of copper pipes used in household drinking-water plumbing is a problem for many water utilities and their customers. Extreme attack can lead to pinhole water leaks that may result in water damage, mold growth, and costly repairs. Water quality has b...

Geochemistry, water balance, and stable isotopes of a “clean” pit lake at an abandoned tungsten mine, Montana, USA

International Nuclear Information System (INIS)

Gammons, Christopher H.; Pape, Barbara L.; Parker, Stephen R.; Poulson, Simon R.; Blank, Carrine E.

2013-01-01

Highlights: • An abandoned open pit mine is now a 30 m deep lake with excellent water quality. • Concentrations of sulfate, nutrients, and most trace metals are extremely low. • Based on water isotopes, the lake is 30% evaporated with a 2.5 yr residence time. • Stable isotopes of DIC and DO track in-lake bio-geochemical processes. • Phytoplankton are active at depths as great as 20 m. - Abstract: The Calvert Mine is a small tungsten-rich (scheelite) skarn deposit in a remote, mountainous region of southwest Montana, USA. The open-pit mine closed in the 1970s and subsequently flooded to form a pit lake that is roughly conical in shape, 30 m deep and 120 m in diameter, with no surface inlet or outlet. The lake is holomictic with a groundwater flow-through hydrology and an estimated residence time of 2.5–5 y. Water isotopes show that the lake is at an approximate steady state with respect to water balance and has experienced 30% evaporation. The lake has a near-neutral pH, exceptional clarity, and extremely low concentrations of nutrients, sulfate, and most metals, including tungsten. Manganese concentrations are slightly elevated and increase with depth towards the sediment–water interface. Despite seasonally anoxic conditions in the deep water, dissolved Fe concentrations are orders of magnitude lower than Mn, suggesting that insufficient organic carbon is present in the sediment of this oligotrophic lake to drive bacterial Fe reduction. Based on stable isotope fingerprinting, diffuse seepage that enters a nearby headwater stream at the base of a large waste-rock pile can be directly linked to the partially evaporated pit lake. However, this seepage has neutral pH and low metal concentrations, and poses no threats to the environment. Stable isotopes of dissolved inorganic carbon (DIC) and dissolved oxygen (DO) are used to track the relative importance of photosynthesis and respiration with depth. In summer, a zone of high productivity exists near the

Software development for geologic information management system on open-pit production

Energy Technology Data Exchange (ETDEWEB)

Li, K.; Tian, A.; Ren, Z.; Pang, Y. [China University of Mining and Technomogy, Xuzhou (China). College of Mineral and Energy Resources

2001-09-01

A software, including geological data gathering and processing, deposit modelling, reserves calculating and mine map plotting, for geologic information management of open-pit production was developed. Based on the interactive technique, CAD, the object-oriented simulation, and the characteristics of geologic structures, all the geologic information databases and geologic mapping sub-systems have been established for open-pit production, planning and management. 6 refs., 1 fig.

Open-pit construction

International Nuclear Information System (INIS)

1981-06-01

The conceptual design of a nuclear power plant accordingly to SR 136, situated in deep open pits in rock near the brink of a plateau and accessible from above as well as horizontally from the receiving stream, was further worked out. The increased backfill covering enables the reactor building to withstand heavier external forces and higher internal pressure caused by contaminated atmosphere in the event of severe hypothetical internal accidents. The leakage of this atmosphere is to be collected in special condensation rooms and another part of it is to be cooled down in these rooms. An outer safety barrier and leakage extraction fans keep this atmosphere substantially enclosed. By that means the consequences of a core melt accident will be reduced considerably. (orig.) [de

Extensive rill erosion and gullying on abandoned pit mining sites in Lusatia, Germany

Science.gov (United States)

Kunth, Franziska; Kaiser, Andreas; Vláčilová, Markéta; Schindewolf, Marcus; Schmidt, Jürgen

2015-04-01

As the major economic driver in the province of Lusatia, Eastern Germany, the large open-cast lignite mining sites characterize the landscape and leave vast areas of irreversible changed post-mining landscapes behind. Cost-intensive renaturation projects have been implemented in order to restructure former mine sites into stabile self-sustaining ecosystems and local recreation areas. With considerable expenditure the pits are stabilized, flooded and surrounding areas are restructured. Nevertheless, heavy soil erosion, extensive gullying and slope instability are challenges for the restructuring and renaturation of the abandoned open-cast mining sites. The majority of the sites remain inaccessible to the public due to instable conditions resulting in uncontrolled slides and large gullies. In this study a combined approach of UAV-based aerial imagery, 3D multi-vision surface reconstruction and physically-based soil erosion modelling is carried out in order to document, quantify and better understand the causes of erosion processes on mining sites. Rainfall simulations have been carried out in lausatian post mining areas to reproduce soil detachment processes and observe the responsible mechanisms for the considerable erosion rates. Water repellency and soil sealing by biological crusts were hindering infiltration and consequently increasing runoff rates despite the mainly sandy soil texture. On non-vegetated experimental plots runoff coefficients up to 87 % were measured. In a modelling routine for a major gully catchment regarding a 50 years rainfall event, simulation results reveal runoff coefficients of up to 84% and erosion rates of 118 Mg*ha^-1. At the sediment pass over point 450Mg of sediments enter the surface water bodies. A system response of this order of magnitude were unexpected by the authorities. By applying 3D multi-vision surface reconstruction a model validation is now possible and further may illustrate the great importance of soil conservation

Interior drains for open pit disposal of uranium mill tailings

International Nuclear Information System (INIS)

Staub, W.P.

1978-01-01

A conceptualized interior drainage system is presented for reducing the environmental impact on natural groundwater by disposal of uranium mill tailings in the mined-out open pit. The evaporation/seepage ratio can be increased through the use of interior drains, long-term monitoring of groundwater quality can be eliminated, and the open pit will not require an extensive liner. Other advantages not related to groundwater are: control of fugitive dust and radon emanation during mill operations and timely reclamation after the impoundment is filled with tailings

78 FR 44625 - Proposed Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-07-24

... DEPARTMENT OF VETERANS AFFAIRS Proposed Information Collection (Open Burn Pit Registry Airborne... to ``OMB Control No. 2900--NEW, Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire... health effects of service members' exposure to toxic airborne chemicals and fumes caused by open burn...

Burn Pit Emissions Exposure and Respiratory and Cardiovascular Conditions Among Airborne Hazards and Open Burn Pit Registry Participants.

Science.gov (United States)

Liu, Jason; Lezama, Nicholas; Gasper, Joseph; Kawata, Jennifer; Morley, Sybil; Helmer, Drew; Ciminera, Paul

2016-07-01

The aim of this study was to determine how burn pit emissions exposure is associated with the incidence of respiratory and cardiovascular conditions. We examined the associations between assumed geographic and self-reported burn pit emissions exposure and respiratory and cardiovascular outcomes in participants of the Airborne Hazards and Open Burn Pit Registry. We found significant dose-response associations for higher risk of self-reported emphysema, chronic bronchitis, or chronic obstructive pulmonary disease with increased days of deployment within 2 miles of selected burn pits (P-trend = 0.01) and self-reported burn pit smoke exposure (P-trend = 0.0005). We found associations between burn pit emissions exposure and higher incidence of post-deployment self-reported respiratory and cardiovascular conditions, but these findings should be interpreted with caution because the surrogate measurements of burn pit emissions exposure in this analysis may not reflect individual exposure levels.

Utilization of open pit burned household waste ash--a feasibility study in Dhaka.

Science.gov (United States)

Haque, Md Obaidul; Sharif, Ahmed

2014-05-01

Informal incineration or open pit burning of waste materials is a common practice in the peripheral area of Dhaka, one of the fastest growing mega-cities in the world. This study deals with the effect of open pit burned (i.e. open burned) household waste bottom ash on fired clay bricks. Between 0 to 50% (by weight) of open pit burned household waste bottom ash was mixed with clay to make bricks. The molded specimens were air-dried at room temperature for 24 h and then oven dried at 100 °C for another 24 h to remove the water. The raw bricks were fired in a muffle furnace to a designated temperature (800, 900 and 1000 °C, respectively). The firing behaviour (mechanical strength, water absorption and shrinkage) was determined. The microstructures, phase compositions and leachates were evaluated for bricks manufactured at different firing temperatures. These results demonstrate that open pit burned ash can be recycled in clay bricks. This study also presents physical observations of the incinerated ash particles and determination of the chemical compositions of the raw materials by wet analysis. Open pit burned ash can be introduced easily into bricks up to 20% wt. The concentrations of hazardous components in the leachates were below the standard threshold for inert waste category landfill and their environmental risk during their use-life step can be considered negligible.

Ground movement and deformation due to dewatering and open pit excavation

International Nuclear Information System (INIS)

Liu, B.; Yang, J.; Zhang, J.

1996-01-01

In the application of stochastic medium theory, it is assumed that ground movement process has the property of Markov Process. Based on superposition principle and rock consolidation principle, the ground movement and deformation due to dewatering and open pit excavation can be calculated. The comparison between the field measurements in Morwell Open Pit, Latrobe Valley (Victoria, Australia) and the calculated results shows the validity of the method in this paper. 5 refs

Structure of energy consumption and improving open-pit dump truck efficiency

Science.gov (United States)

Koptev, V. Yu; Kopteva, A. V.

2017-10-01

This paper studies the dynamics of the improvement of wheel type transport vehicles environmental and energy performance in open-pit mines. The paper discloses characteristics of the gas turbine engine with capacity of 1250 hp, mounted on tanks, and technical-economic calculations, confirming reasonability of their use in open-pit dump trucks with the 120 …130-ton loading capacity. The general layout scheme of mechanical transmission with the gas turbine engine is shown.

78 FR 54956 - Agency Information Collection (Open Burn Pit Registry Airborne Hazard Self-Assessment...

Science.gov (United States)

2013-09-06

...: Open Burn Pit Registry Airborne Hazard Self-Assessment Questionnaire, VA Form 10-10066. Type of Review... services to Open Burn Pit Registry participants and improve VA's ability to understand the health effects... DEPARTMENT OF VETERANS AFFAIRS [OMB Control No. 2900-NEW] Agency Information Collection (Open Burn...

Prediction of the net radon emission from a model open pit uranium mine

International Nuclear Information System (INIS)

Nielson, K.K.; Perkins, R.W.; Schwendiman, L.C.; Enderlin, W.I.

1979-09-01

Radon emission from a model open pit uranium mining operation has been estimated by applying radon exhalation fluxes measured in an open pit uranium mine to the various areas of the model mine. The model mine was defined by averaging uranium concentrations, mine dimensions, production and procedural statistics for eight major open pit uranium mines in the Casper, Wyoming area. The resulting emission rates were 630 Ci/RRY (1 RRY one = 1000-MW(e) reactor operating for 1 year) during mining operations and 26 Ci/RRY/y after abandoment of the mine assuming 100% recovery of U 3 O 8 from the ore, or 700 Ci/RRY and 29 Ci/RRY/y assuming 90.5% recovery

Tectonic fault monitoring at open pit mine at Zarnitsa Kimberlite Pipe

Science.gov (United States)

Vostrikov, VI; Polotnyanko, NS; Trofimov, AS; Potaka, AA

2018-03-01

The article describes application of Karier instrumentation designed at the Institute of Mining to study fracture formation in rocks. The instrumentation composed of three sensors was used to control widening of a tectonic fault intersecting an open pit mine at Zarnitsa Kimberlite Pipe in Yakutia. The monitoring between 28 November and 28 December in 2016 recorded convergence of the fault walls from one side of the open pit mine and widening from the other side. After production blasts, the fault first grows in width and then recovers.

Case history of controlling a landslide at Panluo open-pit mine in China

Science.gov (United States)

Wei, Zuoan; Yin, Guangzhi; Wan, Ling; Shen, Louyan

2008-04-01

Controlling of landsides safely and economically is a great challenge to mine operators because landslides are major geological problems especially in open-pit mines. In this paper, a case history at Panluo open-pit mine is presented in detail to share the experiences and lessons with mine operators. Panluo open-pit mine is located in the southwestern Fujian province of China. It is the largest open-pit iron mine in the Fujian province and was planned in 1965 and is in full operation from 1978. In July 1990, an earthquake of magnitude 5.3 in Taiwan Strait and big rainstorms impacted the mine slope, causing tension cracks and rather large-scale failures, and forming a U-shaped landslide. Total potential volume was estimated to be up to 1.0 × 106 m3. This directly threatened the mine production. In order to protect the mine production and the dwellers’ safety around, a dynamic comprehensive method was implemented including geotechnical investigations, in-situ testing and monitoring, stability analysis, and many mitigation and preventive measures. These measures slowed down the development and further occurrence of the landslide. The results showed that the landslides were still active, it was slowed with the control measures and moved rapidly with rainfall and mining down. However, no catastrophic accidents occurred and the pit mining was continued till it was closed at the elevation of 887 m in 2000. As a successful case of landslide control at an open-pit mine for 10 years, this paper reports the controlling measures in details. These experiences of landslide control may be beneficial to other similar mines for landslide control.

Open pit coal exploitation viability. Margarita mine. Case of study

International Nuclear Information System (INIS)

Veloza, Julia; Molina, Jorge; Mejia, Humberto

2006-01-01

This paper provides an analysis of financial viability, planning and design for the new coal open pit exploitation for La Margarita mine, with coal-resources estimated on 440.139,7 ton. Dimension, design and economic evaluation were possible by three exploitation methods: (multiple bench, open cast contour, and terraces). Net present values (NVP) were calculated: $c 817,5; $c 518,5 and $c 645,2 respectively for each method (given in million current Colombian pesos $. $c 2380 are equivalent to $us 1) and rate of return (ROR) 78,33%; 34,0% and 38,62% respectively for each method. These indicators served as a parameter to choose the multiple bench method, which should be recalculated because it was necessary to work jointly with two pits and making feasible the project. in addition a general environmental evaluation was done, which is vital for the exploitation. Important impacts on the flower, animals, air, water were found, and measures of control, prevention and mitigation were stated. it is expected that this paper can be useful as a technical-economical support for the development of the open pit exploitation in the margarita mine

Modelling open pit shovel-truck systems using the Machine Repair Model

Energy Technology Data Exchange (ETDEWEB)

Krause, A.; Musingwini, C. [CBH Resources Ltd., Sydney, NSW (Australia). Endeaver Mine

2007-08-15

Shovel-truck systems for loading and hauling material in open pit mines are now routinely analysed using simulation models or off-the-shelf simulation software packages, which can be very expensive for once-off or occasional use. The simulation models invariably produce different estimations of fleet sizes due to their differing estimations of cycle time. No single model or package can accurately estimate the required fleet size because the fleet operating parameters are characteristically random and dynamic. In order to improve confidence in sizing the fleet for a mining project, at least two estimation models should be used. This paper demonstrates that the Machine Repair Model can be modified and used as a model for estimating truck fleet size in an open pit shovel-truck system. The modified Machine Repair Model is first applied to a virtual open pit mine case study. The results compare favourably to output from other estimation models using the same input parameters for the virtual mine. The modified Machine Repair Model is further applied to an existing open pit coal operation, the Kwagga Section of Optimum Colliery as a case study. Again the results confirm those obtained from the virtual mine case study. It is concluded that the Machine Repair Model can be an affordable model compared to off-the-shelf generic software because it is easily modelled in Microsoft Excel, a software platform that most mines already use.

Influence of the Haizhou Open Pit Coal Mine on the atmospheric flow over Fuxin, China.

Science.gov (United States)

Chen, He; Yang, Zhi-Feng; Wang, Xuan

2004-01-01

The influence of the Haizhou Open Pit Mine on the atmospheric flow in nearby Fuxin City in China was analyzed with the aid of the steady-state Navier-Stokes equations. The finite element method was used to obtain numerical solutions to these equations. The results showed that the Haizhou Open Pit Coal Mine contributes to the turbulent flow in the Fuxin City and its surroundings. However, when compared with the climatic effects, the open pit mine has a relatively small impact on the atmospheric flow over Fuxin.

Failure Analysis of Pitted Copper Pipes Used in Underground Water and Preventive Measures

Science.gov (United States)

Nam, Gi-ho; Lee, Jong-kwon; Kim, Kyung-ja

2018-05-01

This study performed an experiment on the causes of pitting corrosion in a copper tubing used for a sprinkler system. Corrosion products of a copper tubing that sustained pitting corrosion were collected and cultured in Culture medium [Luria-Bertani, Brain heart infusion, Tryptic soy broth (TSB), R2A]. Four types of bacteria were found through identification: Micrococcus luteus sp (species)., Staphylococcus sp., Sphingomonas sp., and Bacillus sp. The copper toxicity test was performed for each microorganism. Among the four microorganisms, Micrococcus luteus sp. showed good growth in the environment containing copper ions. On the immersion test, changes in pH and Optical density were measured; On the inductively coupled plasma optical emission spectrometry test, the copper concentration of each culture medium was measured. The surface of each copper sample was observed using a scanning electron microscope. The corrosion potential of a copper sample, after 48 h exposure of the TSB medium containing Micrococcus luteus sp., was measured using a potentiodynamic polarization experiment. The next experiment was conducted to prevent microbial corrosion by suppressing the growth of microorganisms. Six 30 ml TSB culture media with controlled pH value of 4, 5, 6, 7, 8, and 9 through HCl and NaOH were manufactured. Then the microorganisms were cultured in 37 °C 133 rpm, of which the growth status was checked every 24 h for 3 days. It was found that microorganisms did not grow on culture media with the pH value of 6 and lower. The same experiment conducted on culture media controlled with acetic acid, nitric acid, and sulfuric acid, also showed no growth of microorganisms on media with pH value of 6 and lower. Six 5 ml TSB culture media each containing 0.5, 0.25, 0.125, 0.0625, 0.0312%, and 0.0156% NaOCl and NaOBr as germicides were manufactured. 0.01 μl of microorganisms were inoculated on the media and cultured in 37 °C for 48 h. It was found that microorganisms did not

Failure Analysis of Pitted Copper Pipes Used in Underground Water and Preventive Measures

Science.gov (United States)

Nam, Gi-ho; Lee, Jong-kwon; Kim, Kyung-ja

2018-03-01

This study performed an experiment on the causes of pitting corrosion in a copper tubing used for a sprinkler system. Corrosion products of a copper tubing that sustained pitting corrosion were collected and cultured in Culture medium [Luria-Bertani, Brain heart infusion, Tryptic soy broth (TSB), R2A]. Four types of bacteria were found through identification: Micrococcus luteus sp (species)., Staphylococcus sp., Sphingomonas sp., and Bacillus sp. The copper toxicity test was performed for each microorganism. Among the four microorganisms, Micrococcus luteus sp. showed good growth in the environment containing copper ions. On the immersion test, changes in pH and Optical density were measured; On the inductively coupled plasma optical emission spectrometry test, the copper concentration of each culture medium was measured. The surface of each copper sample was observed using a scanning electron microscope. The corrosion potential of a copper sample, after 48 h exposure of the TSB medium containing Micrococcus luteus sp., was measured using a potentiodynamic polarization experiment. The next experiment was conducted to prevent microbial corrosion by suppressing the growth of microorganisms. Six 30 ml TSB culture media with controlled pH value of 4, 5, 6, 7, 8, and 9 through HCl and NaOH were manufactured. Then the microorganisms were cultured in 37 °C 133 rpm, of which the growth status was checked every 24 h for 3 days. It was found that microorganisms did not grow on culture media with the pH value of 6 and lower. The same experiment conducted on culture media controlled with acetic acid, nitric acid, and sulfuric acid, also showed no growth of microorganisms on media with pH value of 6 and lower. Six 5 ml TSB culture media each containing 0.5, 0.25, 0.125, 0.0625, 0.0312%, and 0.0156% NaOCl and NaOBr as germicides were manufactured. 0.01 μl of microorganisms were inoculated on the media and cultured in 37 °C for 48 h. It was found that microorganisms did not

Mission-Critical Mobile Broadband Communications in Open Pit Mines

DEFF Research Database (Denmark)

Uzeda Garcia, Luis Guilherme; Portela Lopes de Almeida, Erika; Barbosa, Viviane S. B.

2016-01-01

that need to be met by the wireless network. This article introduces fundamental concepts behind open-pit mining and discusses why this ever changing environment coupled with strict industrial reliability requirements pose unique challenges to traditional broadband network planning and optimization...

Risk assessment of occupational groups working in open pit mining: Analytic Hierarchy Process

Directory of Open Access Journals (Sweden)

Yaşar Kasap

2017-01-01

Full Text Available In open pit mining it is possible to prevent industrial accidents and the results of industrial accidents such as deaths, physical disabilities and financial loss by implementing risk analyses in advance. If the probabilities of different occupational groups encountering various hazards are determined, workers’ risk of having industrial accidents and catching occupational illnesses can be controlled. In this sense, the aim of this study was to assess the industrial accidents which occurred during open pit coal production in the Turkish Coal Enterprises (TCE Garp Lignite unit between 2005 and 2010 and to analyze the risks using the Analytic Hierarchy Process (AHP. The analyses conducted with AHP revealed that the greatest risk in open pit mining is landslides, the most risky occupational group is unskilled labourers and the most common hazards are caused by landslides and transportation/hand tools/falling.

Project design of an open pit colliery in Terkidag, Turkey

Directory of Open Access Journals (Sweden)

H. Kose

2010-10-01

Full Text Available In this manuscript, first of all, the status of Turkey in terms of energy production and consumption is given and the need to relyon domestic sources, namely lignite deposits, is emphasized rather than importing fuels from abroad. Then, a thorough literature workconcerning open pit design and production planning is explained in detail. On this basis, the project design and production planningof Tekirdag-Saray open pit colliery are conducted. According to the selected production technique, machinery-equipment that willbe utilized in the coal winning system is determined and in the final part, the investment cost and unit production cost regardingthe project are computed and the importance of constructing a power plant in the region operating with domestic fuels is expressed.

A New Method for Haul Road Design in Open-Pit Mines to Support Efficient Truck Haulage Operations

Directory of Open Access Journals (Sweden)

Jieun Baek

2017-07-01

Full Text Available The design of a haul road for an open-pit mine can significantly affect the cost associated with hauling ore and waste to the surface. This study proposes a new method for haul road design in open-pit mines to support efficient truck haulage operations. The road layout in open-pit mines was optimized by using raster-based least-cost path analysis, and the resulting zigzag road sections were simplified by applying the Douglas-Peucker algorithm. In addition, the road layout was modified by reflecting the radius of curvature suggested in the road design guides. Finally, a three-dimensional model reflecting the results of the road design was created by combining the road layout modification result with the slope of the open-pit mine and the bench design result. The application of the proposed method to an area containing gold deposits made it possible to design a haul road for open-pit mines such that it supported efficient truck haulage operations; furthermore, the time required for truck movement along the road could be estimated. The proposed method is expected to be useful for planning and designing open-pit mines and to facilitate the improvement of the road design function of existing mining software applications.

Functional Quality Criterion of Rock Handling Mechanization at Open-pit Mines

Directory of Open Access Journals (Sweden)

Voronov Yuri

2017-01-01

Full Text Available Overburden and mining operations at open-pit mines are performed mainly by powerful shovel-truck systems (STSs. One of the main problems of the STSs is a rather low level of their operating quality, mainly due to unjustified over-trucking. In this article, a functional criterion for assessing the qualify of the STS operation at open-pit mines is formulated, derived and analyzed. We introduce the rationale and general principles for the functional criterion formation, its general form, as well as variations for various STS structures: a mixed truck fleet and a homogeneous shovel fleet, a mixed shove! fleet and a homogeneous truck fleet, mixed truck and shovel fleets. The possibility of assessing the quality of the STS operation is of great importance for identifying the main directions for improving their operational performance and operating quality, optimizing the main performance indicators by the qualify criterion, and. as a result, for possible saving of material and technical resources for open-pit mining. Improvement of the quality of the STS operation also allows increasing the mining safety and decreasing the atmosphere pollution - by means of possible reducing of the number of the operating trucks.

Functional Quality Criterion of Rock Handling Mechanization at Open-pit Mines

Science.gov (United States)

Voronov, Yuri; Voronov, Artyoni

2017-11-01

Overburden and mining operations at open-pit mines are performed mainly by powerful shovel-truck systems (STSs). One of the main problems of the STSs is a rather low level of their operating quality, mainly due to unjustified over-trucking. In this article, a functional criterion for assessing the qualify of the STS operation at open-pit mines is formulated, derived and analyzed. We introduce the rationale and general principles for the functional criterion formation, its general form, as well as variations for various STS structures: a mixed truck fleet and a homogeneous shovel fleet, a mixed shove! fleet and a homogeneous truck fleet, mixed truck and shovel fleets. The possibility of assessing the quality of the STS operation is of great importance for identifying the main directions for improving their operational performance and operating quality, optimizing the main performance indicators by the qualify criterion, and. as a result, for possible saving of material and technical resources for open-pit mining. Improvement of the quality of the STS operation also allows increasing the mining safety and decreasing the atmosphere pollution - by means of possible reducing of the number of the operating trucks.

Important improvement of utilization the available geological reserves of the South mining district deposit in Majdanpek in the new defined optimum contour of the open pit using the Whittle and Gemcom softwares

OpenAIRE

Kržanović, Daniel; Žikić, Miodrag; Pantović, Radoje

2012-01-01

A significant increase in copper prices on the World Metal Exchange, whose lower limit in the long term will not be under $ 6,000 per ton of cathode copper, and reduction the operating costs of ore mining by introduction the high capacity mining equipment in the production process, requires a new consideration of the open pit South Mining District Majdanpek and defining the new final (optimum) limit of mining for the given techno economic parameters. Using the modern software tools for strate...

Grader Operator. Open Pit Mining Job Training Series.

Science.gov (United States)

Savilow, Bill

This training outline for grader operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for classroom…

Shovel Operator. Open Pit Mining Job Training Series.

Science.gov (United States)

Hartley, Larry

This training outline for shovel operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for classroom…

Optimization of coal recovery from open pits

Energy Technology Data Exchange (ETDEWEB)

Kim, C; Wolff, S F; Baafi, E Y; Cervantes, J A; Coates, D F

1979-02-01

The design techniques of the Pit Slope Manual were successfully applied in a case study concerned with optimizing the design of coal mines. A steeply dipping multiple seam deposit, being mined by the truck-shovel combination, was selected for the study. The criterion for optimum slopes was based on the financial consequences of each design, i.e., the resultant benefits and costs. Three alternative designs were analyzed. The first had an average highwall slope angle of 28 degrees and a final height of 290 m. The second had a 35 degrees slope angle and a 305-m wall height. The third had a 45 degrees slope angle and a 320-m wall height. Trade-off between benefits and increased cost of slope instability inherent in steeper slope angles was analyzed for the entire mine life through computer simulation of actual mining operations. The cost models developed were (1) No Cost, (2) Clean-up, (3) Lost Coal, (4) Early Mining, (5) Mine Abandonment, (6) Increased Haulage, and (7) Haul Road Re-establishment. (8 refs.)

Pitting corrosion on a copper canister

International Nuclear Information System (INIS)

Hermansson, H.P.; Beverskog, B.

1996-02-01

It is demonstrated that normal pitting can occur during oxidizing conditions in the repository. It is also concluded that a new theory for pitting corrosion has to be developed, as the present theory is not in accordance with all practical and experimental observations. A special variant of pitting, based on the growth of sulfide whiskers, is suggested to occur during reducing conditions. However, such a mechanism needs to be demonstrated experimentally. A simple calculational model of canister corrosion was developed based on the results of this study. 69 refs, 3 figs

The application of GPS to the deformation monitoring of side slope in open-pit uranium mines

International Nuclear Information System (INIS)

Zhu Yufeng; Pan Jiayong; Zhu Guogen; Wang Fei

2009-01-01

GPS has the characters,such as higher accuracy,not influenced by weather and day time. According to actual circumstance of a open pit uranium mine in China. This paper introduces a system to monit the deformation of side sloping and its detail application in a open pit mine. (authors)

EXPLOITATION OF GLASS SAND ON THE OPEN PIT »VRTLINSKA« (MOSLAVINA, CROATIA

Directory of Open Access Journals (Sweden)

Slavko Vujec

1994-12-01

Full Text Available The exploitation of glass sand in Slavonia and Moslavina has a long tradition. The open-pit »Vrtlinska« is-accordirtg to its dimensions and production capacity the biggest one in this regions. Exploitation reserves within this open pit amount about 1 000 000 t glass sand of a very good quality, and the production capacity is 200 000 t yearly according to real needs during design and opening the pit, i. e. before the war. This article discusses geological and geomechanical characteristics of the deposit, as well as the exploitation process, which is considerably matching natural characteristics of the deposit. A more detailed description is given of the planned exploitation phase I above groundwater level which is carried out according to discontinuous system. For the exploitation of the depth part under groundwater level in the phase II, the necessity of further examination of hydrogeological characteristics of the deposit is presented, in order to acquire necessary information on groundwater regime and drainage conditions. Such knowledge will influence the choice of the most appropriate solutions in the exploitation of the depth part of the deposit.

Dewatering of planned Key Lake open pits in northern Saskatchewan

International Nuclear Information System (INIS)

Unland, W.; Holl, N.

1980-01-01

The engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan are presented. An extensive unconfined overburden aquifer is hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. Hydrogeological data were used in a numerical dewatering model simulating groundwater flow at different stages of the pit development. Based on the model results, the enginering design had to provide for different pumping rates, varying between 1.0 and 0.21 m 3 /sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26 dewatering wells are discussed. (auth)

A genetic algorithm approach for open-pit mine production scheduling

Directory of Open Access Journals (Sweden)

Aref Alipour

2017-06-01

Full Text Available In an Open-Pit Production Scheduling (OPPS problem, the goal is to determine the mining sequence of an orebody as a block model. In this article, linear programing formulation is used to aim this goal. OPPS problem is known as an NP-hard problem, so an exact mathematical model cannot be applied to solve in the real state. Genetic Algorithm (GA is a well-known member of evolutionary algorithms that widely are utilized to solve NP-hard problems. Herein, GA is implemented in a hypothetical Two-Dimensional (2D copper orebody model. The orebody is featured as two-dimensional (2D array of blocks. Likewise, counterpart 2D GA array was used to represent the OPPS problem’s solution space. Thereupon, the fitness function is defined according to the OPPS problem’s objective function to assess the solution domain. Also, new normalization method was used for the handling of block sequencing constraint. A numerical study is performed to compare the solutions of the exact and GA-based methods. It is shown that the gap between GA and the optimal solution by the exact method is less than % 5; hereupon GA is found to be efficiently in solving OPPS problem.

Hydrodynamic model of the open-pit mine “Buvač” (Republic of Srpska

Directory of Open Access Journals (Sweden)

Papić Petar

2013-09-01

Full Text Available Projecting of the dewatering system of the open-pit mine “Buvač” (Republic of Srpska, Bosnia and Herzegovina is based on the use of hydrodynamic model of groundwater regime. Creating the hydrodynamic model of the open-pit mine “Buvač“ was made in phases, which began by basic interpretation of collected data, along with schematization of the groundwater flow and flow conditions, and finally, forming and calibration of model. Hydrodynamic model was created as multilayer model with eight layers. Calibration of the hydrodynamic model is the starting point for making prognosis calculation in order to create the most optimal system of open-pit mine protection from groundwater. The results of model calibration indicated that the rivers Gomjenica and Bistrica, precipitation and inflow from karstified rocks are the primary sources of recharge of the limonite ore body “Buvač”.

Exploration on feasibility of using in-situ leaching after explosion on the bottom of Huangfengling open pit

International Nuclear Information System (INIS)

Shi Zuyuan

1992-01-01

According to the situation of mining and the faced problems in Huangfengling open pit, it was proposed to use in-situ leaching after explosion to recover uranium in order to overcome the difficulties with open mining of the deposit and high mining cost. The feasibility and necessity of using in-situ leaching after explosion in Huangfengling open pit was explored

Heavy Duty Tireman. Open Pit Mining Job Training Series.

Science.gov (United States)

McColman, Don

This training outline for heavy duty tiremen, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for classroom…

Track Dozer Operator. Open Pit Mining Job Training Series.

Science.gov (United States)

British Columbia Dept. of Education, Victoria.

This training outline for track dozer operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

Rotary Drill Operator. Open Pit Mining Job Training Series.

Science.gov (United States)

Savilow, Bill

This training outline for rotary drill operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

Haulage Truck Operator. Open Pit Mining Job Training Series.

Science.gov (United States)

British Columbia Dept. of Education, Victoria.

This training outline for haulage truck operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

Millennium Open Pit Mine, Alberta, Canada

Science.gov (United States)

2007-01-01

Near Fort McMurray, Alberta, Canada, on the east bank of the Athabasca River, are found the Steepbank and Millennium mines. These open pit mines produce oil sands that are processed to recover bitumen, and then upgrade it to refinery-ready raw crude oil, and diesel fuel. The ASTER images were acquired September 22, 2000 and July 31, 2007, cover an area of 22.5 x 25.5 km, and are located near 57 degrees north latitude, 111.5 degrees west longitude. The U.S. science team is located at NASA's Jet Propulsion Laboratory, Pasadena, Calif. The Terra mission is part of NASA's Science Mission Directorate.

Why do Pit-Hours outlive the Pit?

NARCIS (Netherlands)

S.R. Ozturk (Sait); M. van der Wel (Michel); D.J.C. van Dijk (Dick)

2015-01-01

markdownabstract__Abstract__ We study why a majority of trades still happen during the pit hours, i.e. when the trading pit is open, even after the pit ceased to be a liquid and informative venue. We investigate the case of 30-year U.S. Treasury futures using a ten-years-long intraday data set

Influence of increasing phosphate/silikate contents on the pitting and general corrosion of galvanized steel tubing and the corrosion of copper in warm water mixed installation systems

International Nuclear Information System (INIS)

Ehreke, J.; Stichel, W.

1989-01-01

In hot tap water (65 0 C) the influence of a mixture of phosphate/silicate inhibitor on the general, the pitting and the galvanic corrosion of galvanized steel tubes and the general corrosion of copper in mixed installations of both metals was investigated. Increasing concentration of inhibitors descreases the general corrosion rate of galvanized steel and copper. A worth mentioning reduction of pitting and galvanic corrosion of steel could be reached only with high concentrations of 5 mg/l P 2 O 5 and 30 mg/l SiO 2 . Galvannealed tubes are much more sensitive to pitting corrosion than galvanized ones. Referring to this they could not be inhibited. (orig.) [de

Corrosion control when using passively treated abandoned mine drainage as alternative makeup water for cooling systems.

Science.gov (United States)

Hsieh, Ming-Kai; Chien, Shih-Hsiang; Li, Heng; Monnell, Jason D; Dzombak, David A; Vidic, Radisav D

2011-09-01

Passively treated abandoned mine drainage (AMD) is a promising alternative to fresh water as power plant cooling water system makeup water in mining regions where such water is abundant. Passive treatment and reuse of AMD can avoid the contamination of surface water caused by discharge of abandoned mine water, which typically is acidic and contains high concentrations of metals, especially iron. The purpose of this study was to evaluate the feasibility of reusing passively treated AMD in cooling systems with respect to corrosion control through laboratory experiments and pilot-scale field testing. The results showed that, with the addition of the inhibitor mixture orthophosphate and tolyltriazole, mild steel and copper corrosion rates were reduced to acceptable levels (< 0.127 mm/y and < 0.0076 mm/y, respectively). Aluminum had pitting corrosion problems in every condition tested, while cupronickel showed that, even in the absence of any inhibitor and in the presence of the biocide monochloramine, its corrosion rate was still very low (0.018 mm/y).

Superficial drainage studies in open-pit mines

International Nuclear Information System (INIS)

Teixeira Junior, P.B.; Leite, C.B.B.

1984-01-01

Drainage studies concerning large open-pit mining projects can be of vital importance throughout the mining activity itself as they may assist in avoiding activity interruptions due to drainage problems, therefore representing substantial savings. These studies should, in fact, be carried out from the initial activity stages and shall be considered in operational, project and planning decisions in order to optimize results and reduce costs. This specific study presents a drainage study systematization proposal, enphasazing economic decision criteria. The authors comment on studies of this nature developed at the Caldas uranium mine - NUCLEBRAS. (D.J.M.) [pt

Natural radioactivity in lignite samples from open pit mines “Kolubara”, Serbia – risk assessment

International Nuclear Information System (INIS)

Đurašević, M.; Kandić, A.; Stefanović, P.; Vukanac, I.; Šešlak, B.; Milošević, Z.; Marković, T.

2014-01-01

Coal as fossil fuel mainly contains naturally occurring radionuclides from the uranium and thorium series and 40 K. Use of coal, primarily in industry, as a result has dispersion of radioactive material from coal in and through air and water. The aim of this study was to determine the activity concentrations of natural radionuclides in coal samples from open pit mines “Kolubara” and to evaluate its effect on population health. The results showed that all measured and calculated values were below the limits recommended in international legislation. - Highlights: • Activity concentrations of natural radionuclides in coal samples were determined. • Effect on population health due to the activity of these radionuclides was estimated. • All samples were collected at different locations of the open pit mines “Kolubara”. • All measured and calculated values were below the recommended limits. • There is no enhanced radiation hazard for population nearby open pit mines

THE SCENIC VALUE OF ABANDONED MINING AREAS IN POLAND

Directory of Open Access Journals (Sweden)

URSZULA MYGA-PIĄTEK

2008-12-01

Full Text Available Abandoned Polish mining areas are commonly heavily transformed so that they endanger no longer the environment. A disadvantage is that the newly created areas commonly contribute to the monotonous urban-industrial landscape, rather than providing additional value. This is partly due to legislation that hampers a more diversified management of abandoned mining areas as potentially valuable landforms. One of the legal barriers that restricts the possibilities of making these areas more attractive, regards the utilization of remaining exploitation holes (i.e. land depressions of at least 2 m deep, formed as a result of open-pit mining of energy, chemical, building or metallurgical resources and waste heaps as important cultural and scenic elements. Such a new use of these old mininginduced phenomena is important if it is intended not only to involve the regional population in the process of exploring and exploiting the earth’s resources, but also to confront them with some negative consequences of these activities, including shaping the landscape in which these objects are situated. The current attitude towards a new architecture for abandoned mining areas should be reconsidered; particularly the present-day approach based on narrow specializations – for instance of experts in mineral exploitation, spatial planning or environmental protection – should be replaced by interdisciplinary action regarding shaping the landscape of abandoned mining areas.

Front End Loader Operator. Open Pit Mining Job Training Series.

Science.gov (United States)

Savilow, Bill

This training outline for front end loader operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

Rubber Tire Dozer Operator. Open Pit Mining Job Training Series.

Science.gov (United States)

British Columbia Dept. of Education, Victoria.

This training outline for rubber tire dozer operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

Measurement of unattached fractions in open-pit uranium mines

International Nuclear Information System (INIS)

Solomon, S.B.; Wise, K.N.

1983-01-01

A preliminary set of measurements of the unattached fraction of potential alpha energy was made at the Ranger open pit uranium uranium mine and the Nabarlek uranium mill. The measurement system, which incorporated a parallel plate diffusion battery and diffuse junction detectors, is described. Results for RaA show a wide variation in the unattached fraction. They range up to 0.76 and are higher than corresponding values for underground mining operations

Birth outcomes among military personnel after exposure to documented open-air burn pits before and during pregnancy.

Science.gov (United States)

Conlin, Ava Marie S; DeScisciolo, Connie; Sevick, Carter J; Bukowinski, Anna T; Phillips, Christopher J; Smith, Tyler C

2012-06-01

To examine birth outcomes in military women and men with potential exposure to documented open-air burn pits before and during pregnancy. Electronic data from the Department of Defense Birth and Infant Health Registry and the Defense Manpower Data Center were used to examine the prevalence of birth defects and preterm birth among infants of active-duty women and men who were deployed within a 3-mile radius of a documented open-air burn pit before or during pregnancy. In general, burn pit exposure at various times in relation to pregnancy and for differing durations was not consistently associated with an increase in birth defects or preterm birth in infants of active-duty military personnel. These analyses offer reassurance to service members that burn pit exposure is not consistently associated with these select adverse infant health outcomes.

CHARACTERIZATION OF LOCALIZED CORROSION OF COPPER PIPES USED IN DRINKING WATER

Science.gov (United States)

Localized corrosion of copper, or "copper pitting" in water distribution tubing is a large problem at many utilities. Pitting can lead to pinhole leaks less than a year. Tubing affected by copper pitting will often fail in ultiple locations, resulting in a frustrating situation ...

An imperialist competitive algorithm for solving the production scheduling problem in open pit mine

Directory of Open Access Journals (Sweden)

Mojtaba Mokhtarian Asl

2016-06-01

Full Text Available Production scheduling (planning of an open-pit mine is the procedure during which the rock blocks are assigned to different production periods in a way that the highest net present value of the project achieved subject to operational constraints. The paper introduces a new and computationally less expensive meta-heuristic technique known as imperialist competitive algorithm (ICA for long-term production planning of open pit mines. The proposed algorithm modifies the original rules of the assimilation process. The ICA performance for different levels of the control factors has been studied and the results are presented. The result showed that ICA could be efficiently applied on mine production planning problem.

A GIS-based, confined aquifer, hypothetical model of ground-water seepage into a former mining open pit

International Nuclear Information System (INIS)

Salama, A; Negeed, E.R.

2010-01-01

Groundwater seepage into a former mining site in Egypt is proposed for simulation. This site was used for basalt extraction. After the mining activities had stopped a large open pit was left over and groundwater seeped into the pit forming a lake. The pit has a dimension of approximately 1200 x 600 x 30 m. Because of the lack of field data, several scenarios may be hypothesized to explain the filling of these open pits with water. In this paper, one of these scenarios is studied. It is suggested that this water comes from an underneath confined aquifer. Through fractures in the host rock, water seeped upwards into the open pit. To estimate the rate at which water seeps into the lake, numerical study based on the finite element method is performed. Firstly, geo-referencing of the site was performed using GIS. The boundary of the lake was then digitized and elevation contours was defined. These data was then imported into grid-builder software to generate a two-dimensional triangular mesh which was then used by hydro-geosphere software to build the three-dimensional mesh and solve the problem. It was found that the set of discrete fractures was insufficient to fill the lake in the time span that was actually elapsed to fill up the lake which is on the order of two to three years.

Assessment and remediation of earthen pits in Alberta

International Nuclear Information System (INIS)

Lye, D.E.; Deibert, L.

1999-01-01

The proper decommissioning of abandoned earthen pits and the elimination of the associated environmental liabilities were discussed. An earthen pit is an excavated pit used by upstream oil and gas companies to contain/store/burn produced fluids and gases from either gas or oil producing operations. Produced fluids may include liquid hydrocarbons, process chemicals and water originating from oil wells, gas wells, and associated batteries and processing facilities. Improper operation and management at some pits has resulted in soil and/or groundwater contamination. In response to regulatory direction, petroleum operators in Alberta have begun the process of replacing earthen pits with alternative flaring and liquid storage facilities, and embarked on programs to assess, remediate and decommission earthen pits at their operations. This paper describes some of the challenges facing petroleum operators in this regard. It also outlines the regulatory framework within which decommissioning projects must be completed. 2 tabs

The Key Factors Analysis of Palisades Temperature in Deep Open-pit Mine

Science.gov (United States)

Wang, Yuan; Du, Cuifeng; Jin, Wenbo; Wang, Puyu

2018-01-01

In order to study the key factors of palisades temperature field in a deep open-pit mine in the natural environment, the influence of natural factors on the palisades temperature in a deep open-pit mine were analysed based on the principle of heat transfer. Four typical places with different ways of solar radiation were selected to carry out the field test. The results show that solar radiation, atmospheric temperature, and wind speed are three main factors affecting the temperature of palisades and that the direct sunlight plays a leading role. The time period of the sun shining directly on the shady slope of the palisades is short because of blocking effect, whose temperature changes in a smaller scale. At the same time, the sun slope of the palisades suffers from the solar radiation for a long time, whose temperature changes in a larger scale, and the variation is similar to the air temperature.

Assessing Health Outcomes After Environmental Exposures Associated With Open Pit Burning in Deployed US Service Members.

Science.gov (United States)

Rohrbeck, Patricia; Hu, Zheng; Mallon, Col Timothy M

2016-08-01

This study assessed the long-term health impact of environmental exposures associated with open pit burning in deployed US service members. Two hundred individuals deployed to Balad, Iraq, and Bagram, Afghanistan, with known exposure to open pits, were matched to 200 non-deployed service members. Both cohorts were observed for adverse health outcomes after returning from deployment. Slight increased risks were observed for respiratory diseases in the Bagram cohort (adj RR: 1.259), and for cardiovascular disease in the Balad cohort (adj RR: 1.072), but the findings were not significant. The combined deployed cohort showed lower risks for adverse health outcomes, suggesting a healthy deployer effect. In conclusion, this study did not find significantly increased risks for selected health outcomes after burn pit exposure during deployment among two deployed cohorts compared with a non-deployed cohort.

Exploring droplet impact near a millimetre-sized hole: comparing a closed pit with an open-ended pore

NARCIS (Netherlands)

de Jong, Rianne; Enriquez Paz y Puente, O.R.; van der Meer, Roger M.

2015-01-01

We investigate drop impact dynamics near closed pits and open-ended pores experimentally. The resulting impact phenomena differ greatly in each case. For a pit, we observe three distinct phenomena, which we denote as a splash, a jet and an air bubble, whose appearance depends on the distance between

Emissions of naturally occurring radioactivity from aluminum and copper facilities. Report No. 6 (final)

International Nuclear Information System (INIS)

Andrews, V.E.

1982-11-01

This report summarizes five surveys which were conducted at a Bauxite mining operation, an alumina reduction plant, an aluminum reduction plant, an underground copper mine and mill, and an open pit copper mine and concentrator. Process components and controlled source releases were sampled for naturally occurring radioactivity. Particular emphasis was given to radon-222, lead-210, and polonium-210 emissions from crushing and drying processes

Modern carbonate microbialites from an asbestos open pit pond, Yukon, Canada.

Science.gov (United States)

Power, I M; Wilson, S A; Dipple, G M; Southam, G

2011-03-01

Microbialites were discovered in an open pit pond at an abandoned asbestos mine near Clinton Creek, Yukon, Canada. These microbialites are extremely young and presumably began forming soon after the mine closed in 1978. Detailed characterization of the periphyton and microbialites using light and scanning electron microscopy was coupled with mineralogical and isotopic analyses to investigate the mechanisms by which these microbialites formed. The microbialites are columnar in form (cm scale), have an internal spherulitic fabric (mm scale), and are mostly made of aragonite, which is supersaturated in the subsaline pond water. Initial precipitation is seen as acicular aragonite crystals nucleating onto microbial biomass and detrital particles. Continued precipitation entombs benthic diatoms (e.g. Brachysira vitrea), filamentous algae (e.g. Oedogonium sp.), dinoflagellates, and cyanobacteria. The presence of phototrophs at spherulite centers strongly suggests that these microbes play an important initial role in aragonite precipitation. Substantial growth of individual spherulites occurs abiotically through periodic precipitation of aragonite that forms concentric laminations around spherulite centers while pauses in spherulite growth allow for colonization by microbes. Aragonite associated with biomass (δ(13)C = -4.6‰ VPDB) showed a (13)C-enrichment of 0.8‰ relative to aragonite exhibiting no biomass (δ(13)C = -5.4‰ VPDB), which suggests a modest removal of isotopically light dissolved inorganic carbon by phototrophs. The combination of a low sedimentation rate, high calcification rate, and low microbial growth rate appears to result in the formation of these microbialites. The formation of microbialites at an historic mine site demonstrates that an anthropogenically constructed environment can foster microbial carbonate formation. © 2011 Blackwell Publishing Ltd.

Radio Propagation in Open-pit Mines

DEFF Research Database (Denmark)

Portela Lopes de Almeida, Erika; Caldwell, George; Rodriguez Larrad, Ignacio

2017-01-01

In this paper we present the results of an extensive measurement campaign performed at two large iron ore mining centers in Brazil at the 2.6 GHz band. Although several studies focusing on radio propagation in underground mines have been published, measurement data and careful analyses for open......-pit mines are still scarce. Our results aim at filling this gap in the literature. The research is motivated by the ongoing mine automation initiatives, where connectivity becomes critical. This paper presents the first set of results comprising measurements under a gamut of propagation conditions. A second...... paper detailing sub-GHz propagation is also in preparation. The results indicate that conventional wisdom is wrong, in other words, radio-frequency (RF) propagation in surface mines can be far more elaborate than plain free-space line-of-sight conditions. Additionally, the old mining adage “no two mines...

The Three-Dimensional (3D) Numerical Stability Analysis of Hyttemalmen Open-Pit

Science.gov (United States)

Cała, Marek; Kowalski, Michał; Stopkowicz, Agnieszka

2014-10-01

The purpose of this paper was to perform the 3D numerical calculations allowing slope stability analysis of Hyttemalmen open pit (location Kirkenes, Finnmark Province, Norway). After a ramp rock slide, which took place in December 2010, as well as some other small-scale rock slope stability problems, it proved necessary to perform a serious stability analyses. The Hyttemalmen open pit was designed with a depth up to 100 m, a bench height of 24 m and a ramp width of 10 m. The rock formation in the iron mining district of Kirkenes is called the Bjornevaten Group. This is the most structurally complicated area connected with tectonic process such as folding, faults and metamorphosis. The Bjornevaten Group is a volcano-sedimentary sequence. Rock slope stability depends on the mechanical properties of the rock, hydro-geological conditions, slope topography, joint set systems and seismic activity. However, rock slope stability is mainly connected with joint sets. Joints, or general discontinuities, are regarded as weak planes within rock which have strength reducing consequences with regard to rock strength. Discontinuities within the rock mass lead to very low tensile strength. Several simulations were performed utilising the RocLab (2007) software to estimate the gneiss cohesion for slopes of different height. The RocLab code is dedicated to estimate rock mass strength using the Hoek-Brown failure criterion. Utilising both the GSI index and the Hoek-Brown strength criterion the equivalent Mohr-Coulomb parameters (cohesion and angle of internal friction) can be calculated. The results of 3D numerical calculations (with FLA3D code) show that it is necessary to redesign the slope-bench system in the Hyttemalmen open pit. Changing slope inclination for lower stages is recommended. The minimum factor of safety should be equal 1.3. At the final planned stage of excavation, the factor of safety drops to 1.06 with failure surface ranging through all of the slopes. In the case

Mining and technological characteristics of future open-pit mine at Brod-Gneotino

International Nuclear Information System (INIS)

Tasevski, Apostol; Demjanski, Kiril; And others

2005-01-01

Development program of Electric Power Company of Macedonia includes to open several pits of coal with aim to prolongate the working period of TPP Bitola, of which one is the bed Brod-Gneotino. This coal bed is characterized with some characteristic mining and technological parameters described in thi paper. (Author)

Proposed open-pit mine threatens Jasper National Park

Energy Technology Data Exchange (ETDEWEB)

Mikelcic, S.

1996-12-31

Concerns by the Sierra Club, the Alberta Wilderness Association, and other environmental groups about the proposed Cheviot Mine are discussed. Cardinal River Coals, which is owned by Luscar Ltd. and Consolidated Coals of Pittsburgh, is proposing the mining operation, which includes 26 deep open pit mines of which 14 will not be backfilled. The mine extends to within 2 km of Jasper National Park`s border. Concerns about the mine include: disruption of an environmentally sensitive area, interference with grizzly bear movement and bighorn sheep habitat and diet, destruction of flora and fauna, and pollution of two major watersheds. Hearings for the mine commence in January 1997.

Storage and Management of Open-pit Transportation Path

Directory of Open Access Journals (Sweden)

Jiusheng Du

2013-07-01

Full Text Available This paper is aiming at the actual demand of open-pit mine daily production scheduling and positioning monitoring. After extracting data from existing topographic maps and other information, it discusses the feasibility of using this data to establish thematic database. By considering the extensive application of GPS data, utilizing new spatial data types of SQL Server 2008 for data storage and management. Extracting data algorithms such as the node spatial data, the regional boundary and the path are implemented, then spatial data storage and management is also realized. It provides the basis for the production of decision-making and production cost savings.

Close-out of open pit and waste rock piles of a uranium mine in Guangxi province of China

International Nuclear Information System (INIS)

Xu Lechang; Zhang Zhao; Zhang Guopu; Liu Min

2012-01-01

Close-out of projects of a mine in Guangxi province of China includes open pit,east and west waste rock piles, ore transfer station, industrial fields, buildings, ore transporting road, and equipment and conduits. The following remediation limits are introduced: environment penetrating radiation dose rate and 222 Rn flux of open pit and waste rock piles, 226 Ra specific activity of soil and individual dose. Remediation objective and programme are discussed in details. Remediation effects are evaluated. (authors)

Numerical modelling of the groundwater inflow to an advancing open pit mine: Kolahdarvazeh pit, Central Iran.

Science.gov (United States)

Bahrami, Saeed; Doulati Ardejani, Faramarz; Aslani, Soheyla; Baafi, Ernest

2014-12-01

The groundwater inflow into a mine during its life and after ceasing operations is one of the most important concerns of the mining industry. This paper presents a hydrogeological assessment of the Irankuh Zn-Pb mine at 20 km south of Esfahan and 1 km northeast of Abnil in west-Central Iran. During mine excavation, the upper impervious bed of a confined aquifer was broken and water at high-pressure flowed into an open pit mine associated with the Kolahdarvazeh deposit. The inflow rates were 6.7 and 1.4 m(3)/s at the maximum and minimum quantities, respectively. Permeability, storage coefficient, thickness and initial head of the fully saturated confined aquifer were 3.5 × 10(-4) m/s, 0.2, 30 m and 60 m, respectively. The hydraulic heads as a function of time were monitored at four observation wells in the vicinity of the pit over 19 weeks and at an observation well near a test well over 21 h. In addition, by measuring the rate of pumping out from the pit sump, at a constant head (usually equal to height of the pit floor), the real inflow rates to the pit were monitored. The main innovations of this work were to make comparison between numerical modelling using a finite element software called SEEP/W and actual data related to inflow and extend the applicability of the numerical model. This model was further used to estimate the hydraulic heads at the observation wells around the pit over 19 weeks during mining operations. Data from a pump-out test and observation wells were used for model calibration and verification. In order to evaluate the model efficiency, the modelling results of inflow quantity and hydraulic heads were compared to those from analytical solutions, as well as the field data. The mean percent error in relation to field data for the inflow quantity was 0.108. It varied between 1.16 and 1.46 for hydraulic head predictions, which are much lower values than the mean percent errors resulted from the analytical solutions (from 1.8 to 5

Thermal comfort sustained by cold protective clothing in Arctic open-pit mining-a thermal manikin and questionnaire study.

Science.gov (United States)

Jussila, Kirsi; Rissanen, Sirkka; Aminoff, Anna; Wahlström, Jens; Vaktskjold, Arild; Talykova, Ljudmila; Remes, Jouko; Mänttäri, Satu; Rintamäki, Hannu

2017-12-07

Workers in the Arctic open-pit mines are exposed to harsh weather conditions. Employers are required to provide protective clothing for workers. This can be the outer layer, but sometimes also inner or middle layers are provided. This study aimed to determine how Arctic open-pit miners protect themselves against cold and the sufficiency, and the selection criteria of the garments. Workers' cold experiences and the clothing in four Arctic open-pit mines in Finland, Sweden, Norway and Russia were evaluated by a questionnaire (n=1,323). Basic thermal insulation (I cl ) of the reported clothing was estimated (ISO 9920). The I cl of clothing from the mines were also measured by thermal manikin (standing/walking) in 0.3 and 4.0 m/s wind. The questionnaire showed that the I cl of the selected clothing was on average 1.2 and 1.5 clo in mild (-5 to +5°C) and dry cold (-20 to -10°C) conditions, respectively. The I cl of the clothing measured by thermal manikin was 1.9-2.3 clo. The results show that the Arctic open-pit miners' selected their clothing based on occupational (time outdoors), environmental (temperature, wind, moisture) and individual factors (cold sensitivity, general health). However, the selected clothing was not sufficient to prevent cooling completely at ambient temperatures below -10°C.

Open-pit production and control at Roessing

International Nuclear Information System (INIS)

Hodson, D.; Rich, C.

1986-01-01

In recent years metal prices have been severely depressed and most companies have directed efforts to controlling costs in order to stay in business. Roessing Uranium has consistently kept uranium production cost increases well below the domestic inflation rate and this has been the result of a firm commitment to production and cost control, which is the main theme of this paper. The subject of cost analysis is briefly presented and the paper then gives more technical detail under the main headings of grade control, production control and engineering projects. The main communication channels, which are used to ensure that different departments on the mine are all working for the same objectives, are mentioned. The paper, however, is intended to be a general overview of the engineering aspects of open-pit cost control

IMPROVING THE ORGANIZATION OF THE SHOVEL-TRUCK SYSTEMS IN OPEN-PIT COAL MINES

Directory of Open Access Journals (Sweden)

Mark KORYAGIN

2017-06-01

Full Text Available The aim of the study is to reduce idle times of mining trucks and shovels in an open-pit coal mine. A heuristic algorithm for making dispatching decisions in conditions of dynamic allocation of trucks is developed. Priority parameters for choosing the shovel after the end-of-truck unloading are introduced. Also, an algorithm for searching for the optimal priority parameters to satisfy the required efficiency criterion is developed. This algorithm is based on a simulation model of a shovel-truck system. The proposed approach is applicable in terms of the group of shovels with a common dump point in various open-pit coal mines. The importance of this work lies in the fact that the proposed model takes into account the random factors related with the duration of loading and dumping, truck movement, repair of shovels and haul trucks, as well as the duration of periods between repairs.

An Empirical Study of Propagation Models for Wireless Communications in Open-pit Mines

DEFF Research Database (Denmark)

Portela Lopes de Almeida, Erika; Caldwell, George; Rodriguez Larrad, Ignacio

2018-01-01

—In this paper, we investigate the suitability of the propagation models ITU-R 526, Okumura Hata, COST Hata models and Standard Propagation Model (SPM) to predict the path loss in open-pit mines. The models are evaluated by comparing the predicted data with measurements obtained in two operational...

Groundwater flow modelling of an abandoned partially open repository

Energy Technology Data Exchange (ETDEWEB)

Bockgaard, Niclas (Golder Associates AB (Sweden))

2010-12-15

As a part of the license application, according to the nuclear activities act, for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The modelling study presented here serves as an input for analyses of so-called future human actions that may affect the repository. The objective of the work was to investigate the hydraulic influence of an abandoned partially open repository. The intention was to illustrate a pessimistic scenario of the effect of open tunnels in comparison to the reference closure of the repository. The effects of open tunnels were studied for two situations with different boundary conditions: A 'temperate' case with present-day boundary conditions and a generic future 'glacial' case with an ice sheet covering the repository. The results were summarized in the form of analyses of flow in and out from open tunnels, the effect on hydraulic head and flow in the surrounding rock volume, and transport performance measures of flow paths from the repository to surface

Groundwater flow modelling of an abandoned partially open repository

International Nuclear Information System (INIS)

Bockgaard, Niclas

2010-12-01

As a part of the license application, according to the nuclear activities act, for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The modelling study presented here serves as an input for analyses of so-called future human actions that may affect the repository. The objective of the work was to investigate the hydraulic influence of an abandoned partially open repository. The intention was to illustrate a pessimistic scenario of the effect of open tunnels in comparison to the reference closure of the repository. The effects of open tunnels were studied for two situations with different boundary conditions: A 'temperate' case with present-day boundary conditions and a generic future 'glacial' case with an ice sheet covering the repository. The results were summarized in the form of analyses of flow in and out from open tunnels, the effect on hydraulic head and flow in the surrounding rock volume, and transport performance measures of flow paths from the repository to surface

Developing an Ecological Passport for an Open-Pit Dump Truck to Reduce Negative Effect on Environment

Science.gov (United States)

Koptev, V. Yu; Kopteva, A. V.

2017-05-01

Expanding the open-pit dump truck usage areas and the need to transport more and more minerals results in producing more and more powerful open-pit dump trucks, and this all is about environmental problems and potential health risks for the personnel. Harmful gas concentrations in working areas became threatening enough to have the work in some areas completely halted, until the contents of harmful substances in the air, as well as visibility on the roads, get back to norm. The article represents the new methodology for assessing comparatively the efficiency of modern transportation systems with performance and ecology characteristics taken into account, by developing an ecological passport for machines, facilitating design improvements and reducing pollution during operation.

The open-pit truck dispatching method based on the completion of production target and the truck flow saturation

Energy Technology Data Exchange (ETDEWEB)

Xing, J.; Sun, X. [Northeastern University, Shenyang (China)

2007-05-15

To address current problems in the 'modular dispatch' dynamic programming system widely used in open-pit truck real-time dispatching, two concepts for meeting production targets and truck flow saturation were proposed. Using truck flow programming and taking into account stochastic factors and transportation distance, truck real-time dispatching was optimised. The method is applicable to both shovel-truck match and mismatching and also to empty and heavy truck dispatching. In an open-pit mine the production efficiency could be increased by between 8% and 18%. 6 refs.

The Experience of Using Innovative Artificial Filter Arrays on South Kuzbass Open Pit: Case Study

Directory of Open Access Journals (Sweden)

Tyulenev Maxim

2017-01-01

Full Text Available The article describes the detailed example of placement of artificial filter arrays in one of Kuzbass open pits. It is proved that the use of the existing rock dump as an artificial filter array allows cleaning the quarry wastewater to the required parameters. Therefore, for water purification, it is possible to pile a new array as well as to use the existing dump, which will reduce the operating costs and the land consumption of open pit mining operations. Also, a brief methodology for determining the parameters of the artificial filter array is given in the article, taking into account the volume of contaminated water, the degree of its contamination and the location of the filter. The proposed complex of measures significantly improves the geo-ecological situation of mining region.

Open pit mining profit maximization considering selling stage and waste rehabilitation cost

Science.gov (United States)

Muttaqin, B. I. A.; Rosyidi, C. N.

2017-11-01

In open pit mining activities, determination of the cut-off grade becomes crucial for the company since the cut-off grade affects how much profit will be earned for the mining company. In this study, we developed a cut-off grade determination mode for the open pit mining industry considering the cost of mining, waste removal (rehabilitation) cost, processing cost, fixed cost, and selling stage cost. The main goal of this study is to develop a model of cut-off grade determination to get the maximum total profit. Secondly, this study is also developed to observe the model of sensitivity based on changes in the cost components. The optimization results show that the models can help mining company managers to determine the optimal cut-off grade and also estimate how much profit that can be earned by the mining company. To illustrate the application of the models, a numerical example and a set of sensitivity analysis are presented. From the results of sensitivity analysis, we conclude that the changes in the sales price greatly affects the optimal cut-off value and the total profit.

Hydrological conceptual model characterisation of an abandoned mine site in semiarid climate. The Sierra de Cartagena-La Unión (SE Spain)

OpenAIRE

ROBLES ARENAS, V.M.; CANDELA, L.

2010-01-01

A comprehensive study at Sierra de Cartagena-La Unión (SE Spain) abandoned mine site was carried out to characterise the regime and water quality of the groundwater system after the mine closure. The system consists of five geologic fractured blocks belonging to the Alpujarride and Nevado-Filabride complexes. The aquifer units are composed of limestone and dolostone materials. Recharge is mainly controlled by the N-130 fault system, man-made induced fractures, open-pits and underground workin...

NPV risk simulation of an open pit gold mine project under the O'Hara cost model by using GAs

Institute of Scientific and Technical Information of China (English)

Franco-Sepulveda Giovanni; Campuzano Carlos; Pineda Cindy

2017-01-01

This paper analyzes an open pit gold mine project based on the O'Hara cost model. Hypothetical data is proposed based on different authors that have studied open pit gold projects, and variations are proposed according to the probability distributions associated to key variables affecting the NPV, like production level, ore grade, price of ore, and others, so as to see what if, in a gold open pit mine project of 3000 metric tons per day of ore. Two case scenarios were analyzed to simulate the NPV, one where there is low certainty data available, and the other where the information available is of high certainty. Results based on genetic algorithm metaheuristic simulations, which combine basically Montecarlo simulations provided by the Palisade Risk software, the O'Hara cost model, net smelter return and financial analysis tools offered by Excel are reported, in order to determine to which variables of the project is more sensitive the NPV.

MINE WASTE TECHNOLOGY PROGRAM PREVENTION OF ACID MINE DRAINAGE GENERATION FROM OPEN-PIT HIGHWALLS

Science.gov (United States)

This document summarizes the results of Mine Waste Technology Program Activity III, Project 26, Prevention of Acid Mine Drainage Generation from Open-Pit Highwalls. The intent of this project was to obtain performance data on the ability of four technologies to prevent the gener...

Radon and aerosol release from open-pit uranium mining

International Nuclear Information System (INIS)

Thomas, V.W.; Nielson, K.K.; Mauch, M.L.

1982-08-01

The quantity of 222 Rn (hereafter called radon) released per unit of uranium produced from open pit mining has been determined. A secondary objective was to determine the nature and quantity of airborne particles resulting from mine operations. To accomplish these objectives, a comprehensive study of the release rates of radon and aerosol material to the atmosphere was made over a one-year period from April 1979 to May 1980 at the Morton Ranch Mine which was operated by United Nuclear Corporation (UNC) in partnership with Tennessee Valley Authority (TVA). The mine is now operated for TVA by Silver King Mines. Morton Ranch Mine was one of five open pit uranium mines studied in central Wyoming. Corroborative measurements were made of radon flux and 226 Ra (hereafter called radium) concentrations of various surfaces at three of the other mines in October 1980 and again at these three mines plus a fourth in April of 1981. Three of these mines are located in the Powder River Basin, about 80 kilometers east by northeast of Casper. One is located in the Shirley Basin, about 60 km south of Casper, and the remaining one is located in the Gas Hills, approximately 100 km west of Casper. The one-year intensive study included simultaneous measurement of several parameters: continuous measurement of atmospheric radon concentration near the ground at three locations, monthly 24-hour radon flux measurements from various surfaces, radium analyses of soil samples collected under each of the flux monitoring devices, monthly integrations of aerosols on dichotomous aerosol samplers, analysis of aerosol samplers for total dust loading, aerosol elemental and radiochemical composition, aerosol elemental composition by particle size, wind speed, wind direction, temperature, barometric pressure, and rainfall

Analysis of disposal of uranium mill tailings in a mined out open pit

International Nuclear Information System (INIS)

Staub, W.P.; Triegel, E.K.

1978-08-01

Mined out open pits are presently under consideration as disposal sites for uranium mill tailings. In this method of tailings management, the escape of contaminated liquid into an adjacent aquifer is the principal environmental concern. The modified Bishop Method was used to analyze the structural stability of a clay liner along the highwall and fluid flow models were used to analyze the effect of tailings solutions on groundwater under several operating conditions. The slope stability of a clay liner was analyzed at three stages of operation: (1) near the beginning of construction, (2) when the pit is partially filled with tailings, and (3) at the end of construction. Both clay lined and unlined pits were considered in the fluid flow modeling. Finally, the seepage of tailings solutions through the clay liner was analyzed. Results of the slope stability analysis showed that it would be necessary to construct the clay liner as a modified form of engineered embankment. This embankment would be similar in construction to that of an earthfill dam. It could be constructed on a 1 : 1 slope provided the tailings slurry were managed properly. It would be necessary to maintain the freeboard height between the embankment and tailings at less than 4 m. A partially dewatered sand beach would have to be located adjacent to the embankment. Potential leakage and aquifer contamination was modeled for lined and unlined pits of various designs. Sulfate, and possibly U and Th, are the most likely contaminants. Results from the model showed the clay and soil cement lined pit to be most effective in containing the pollutants

Open Pit Mining & The Cost of Water Potential Opportunities Towards Sustainable Mining

OpenAIRE

Sébastien J.R. Fortin

2015-01-01

Mining operations require vast quantities of water to run ore processing facilities and thus have a responsibility to manage this critical resource. Operations are often located in areas of limited water supply, which may create a competitive climate for water consumption. Make-up water for mineral processing can represent a significant portion of production cost for mining companies. While necessary for mining, water in open pits is problematic for extraction activities and leads to increase...

A hybrid heuristic algorithm for the open-pit-mining operational planning problem.

OpenAIRE

Souza, Marcone Jamilson Freitas; Coelho, Igor Machado; Ribas, Sabir; Santos, Haroldo Gambini; Merschmann, Luiz Henrique de Campos

2010-01-01

This paper deals with the Open-Pit-Mining Operational Planning problem with dynamic truck allocation. The objective is to optimize mineral extraction in the mines by minimizing the number of mining trucks used to meet production goals and quality requirements. According to the literature, this problem is NPhard, so a heuristic strategy is justified. We present a hybrid algorithm that combines characteristics of two metaheuristics: Greedy Randomized Adaptive Search Procedures and General Varia...

Accuracy of single count methods of WL determination for open-pit uranium mines

International Nuclear Information System (INIS)

Solomon, S.B.; Kennedy, K. N.

1983-01-01

A study of single count methods of WL determination was made using a database respresentative of Australian open pit uranium mine conditions. The aim of the study was to check the existence of the optimum time delay coresponding to the Rolle method, to determine the accuracy of the conversion factor for Australian conditions and to examine any systematic use of data bases of representative radon daughter concentration

Alternative utilization of underground spaces with abandoned mine openings

Energy Technology Data Exchange (ETDEWEB)

Chung, So Keul; Cho, Won Jai; Han, Kong Chang; Choi, Sung Oong [Korea Institute of Geology Mining and Materials, Taejon (Korea)

1998-12-01

Utilization of the openings of the abandoned mines could be planned by the principal parameters such as location and geotechnical impact. The local governments have not only to lead the each stage of the utilization project from the very beginning of conceptual design up to the construction stage, but also to promote the project for the development of public purpose. The possible tentative candidates for the utilization of the abandoned mine openings which are supported by the local governments could be summarized as follows. a. The Gahak mine of Kwangmyung, Kyunggi: The mine caverns which have been served as the storage of the pickled fishes, could be reexcavated by taking into consideration the geotechnical parameters for the public use such as: 1) Training center for the youth, 2) Fermentation and storehouse of marine products, 3) Sightseeing resort, 4) Sports and leisure complex, 5) Underground parking lot, 6) Underground shopping mall and chilled room storage, 7) Library, concert hall and museum. b. Hamtae mine of Taebaek, Kangwon: The Hambaek main haulage way and its shaft should be investigated in detail in order to find out a possible use as the underground challenging park of the coal mining operation. c. Mines of Boryung and Hongsung, Chungnam: Lots of mine caverns have been used as the storehouse for the pickled shrimp. However, they have to be promoted to a large scale industries. d. Imgok mine of Kwangju and Palbong mine of Jeongeup, Chunbuk: Mine caverns which have been used as the storehouse of pickles, need a detailed investigation for alternative promotion. e. Yongho mine of Pusan Dalsung mine of Taegu: Both of the mines are located near metropolitan communities. Reconstruction of the old mine caverns of the Yongho mine is highly recommended for a public use. The caverns of the Dalsung mine could be utilized as the storage facilities. Detailed geotechnical survey and sit investigation could be suggested to design the recommended facilities for both

A decision support system using analytical hierarchy process (AHP) for the optimal environmental reclamation of an open-pit mine

Science.gov (United States)

Bascetin, A.

2007-04-01

The selection of an optimal reclamation method is one of the most important factors in open-pit design and production planning. It also affects economic considerations in open-pit design as a function of plan location and depth. Furthermore, the selection is a complex multi-person, multi-criteria decision problem. The group decision-making process can be improved by applying a systematic and logical approach to assess the priorities based on the inputs of several specialists from different functional areas within the mine company. The analytical hierarchy process (AHP) can be very useful in involving several decision makers with different conflicting objectives to arrive at a consensus decision. In this paper, the selection of an optimal reclamation method using an AHP-based model was evaluated for coal production in an open-pit coal mine located at Seyitomer region in Turkey. The use of the proposed model indicates that it can be applied to improve the group decision making in selecting a reclamation method that satisfies optimal specifications. Also, it is found that the decision process is systematic and using the proposed model can reduce the time taken to select a optimal method.

Contributions to the workshop `Residual ponds from open pit brown coal mining`; Beitraege zum Workshop ``Braunkohlebergbaurestseen``

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

The contributions to the workshop ``Investigations on flooding in residual ponds from open-pit mining`` deal, inter alia, with the hydrochemical development of flushing waters, the stability of the water quality of residual lakes, especially under the impact of land contamination, the influence of brine receipts by flushed residual lakes, and with the microbiological ecology of residual lakes from mining. Furthermore, geophysical studies for demonstrating paths of flow and for calculating the depth and volume of residual lakes from open-pit mining are discussed. (MSK) [Deutsch] Die Beitraege zu dem Workshop `Untersuchungen zu Flutungen in Tagebaurestseen` befassen sich unter anderem mit der hydrochemischen Entwicklung von Flutungsgewaessern, mit der Qualitaetsstabilitaet von Restseewaessern - insbesonders bei Einwirkung von Altlasten - und mit den Einfluessen von Solezufluessen bei Restseeflutung sowie mit Untersuchungen zur mikrobiologischen Oekologie in Bergbaurestseen. Desweiteren werden geophysikalische Untersuchungen zum Nachweis von Fliesswegen und die Tiefen- und Volumenberechnung eines Tagebaurestlochsees erlaeutert. (MSK)

Contributions to the workshop `Residual ponds from open pit brown coal mining`; Beitraege zum Workshop ``Braunkohlebergbaurestseen``

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

The contributions to the workshop ``Investigations on flooding in residual ponds from open-pit mining`` deal, inter alia, with the hydrochemical development of flushing waters, the stability of the water quality of residual lakes, especially under the impact of land contamination, the influence of brine receipts by flushed residual lakes, and with the microbiological ecology of residual lakes from mining. Furthermore, geophysical studies for demonstrating paths of flow and for calculating the depth and volume of residual lakes from open-pit mining are discussed. (MSK) [Deutsch] Die Beitraege zu dem Workshop `Untersuchungen zu Flutungen in Tagebaurestseen` befassen sich unter anderem mit der hydrochemischen Entwicklung von Flutungsgewaessern, mit der Qualitaetsstabilitaet von Restseewaessern - insbesonders bei Einwirkung von Altlasten - und mit den Einfluessen von Solezufluessen bei Restseeflutung sowie mit Untersuchungen zur mikrobiologischen Oekologie in Bergbaurestseen. Desweiteren werden geophysikalische Untersuchungen zum Nachweis von Fliesswegen und die Tiefen- und Volumenberechnung eines Tagebaurestlochsees erlaeutert. (MSK)

An assessment of corrosion life of copper overpack

International Nuclear Information System (INIS)

Honda, A.; Taniguchi, N.

1999-08-01

Corrosion life of copper overpack is estimated on the basis of current understandings of copper corrosion processes. The assessment is based on the mass balance. Oxygen and sulfide were taken into account as corrosive species. The sulfate existing in bentonite is assumed to be reduced to sulfide by sulfate reducing bacteria and corrodes copper overpacks. Pitting is involved in the assesment using two methods. One method is use of pitting factor acquired from analysis of archeological artifacts. The other is use of extreme value statistical technique. The time evolution of parameters for cumulative probability distribution function, Gumbel distribution, was estimated using the data from copper specimens buried in various soil and archeological artifacts of the bronze age. The pitting depth for 1000 years is estimated using the parameters for probability distribution function. The result of estimation shows 39-mm is the maximum penetration for 1000 years. Natural analogue data suggest the corrosion rate of 3 mm/1000 years. Therefore the estimation is considered to be conservative. (author)

Prospective assessment of chronic multisymptom illness reporting possibly associated with open-air burn pit smoke exposure in Iraq.

Science.gov (United States)

Powell, Teresa M; Smith, Tyler C; Jacobson, Isabel G; Boyko, Edward J; Hooper, Tomoko I; Gackstetter, Gary D; Phillips, Christopher J; Smith, Besa

2012-06-01

To investigate the relationship between chronic multisymptom illness (CMI) and possible exposure to an open-air burn pit at three selected bases among those deployed to operations in Iraq and Afghanistan. Chronic multisymptom illness (reporting at least one symptom in at least two of the following symptom constructs: general fatigue; mood and cognition problems; and musculoskeletal discomfort) was assessed, differentiating by potential burn pit exposure, among deployers who completed 2004 and 2007 Millennium Cohort questionnaires. More than 21,000 Cohort participants were deployed in support of the current operations, including more than 3000 participants with at least one deployment within a 3-mile radius of a documented burn pit. After adjusting for covariates, no elevated risk of CMI was observed among those exposed. There was no increase in CMI symptom reporting in those deployed to three selected bases with documented burn pits compared with other deployers.

Analysis of disposal of uranium mill tailings in a mined out open pit

International Nuclear Information System (INIS)

Staub, W.P.; Triegel, E.K.

1978-01-01

Mined out open pits are presently under consideration as disposal sites for uranium mill tailings. In this method of tailings management, the escape of contaminated liquid into an adjacent aquifer is the principal environmental concern. The modified Bishop Method was used to analyze the structural stability of a clay liner along the highwall and fluid flow models were used to analyze the effect of tailings solutions on ground water under several operating conditions. Results of the slope stability analysis showed that it would be necessary to construct the clay liner as a modified form of engineered embankment. This embankment would be similar in construction to that of an earthfill dam. It could be constructed on a 1:1 slope provided the tailings slurry were managed properly. It would be necessary to maintain the freeboard height between the embankment and tailings at less than 4 m. A partially dewatered sand beach would have to be located adjacent to the embankment. Potential leakage and aquifer contamination was modeled for lined and unlined pits of various designs. Sulfate, and possibly U and Th, are the most likely contaminants. Results from the model showed the clay and soil cement lined pit to be most effective in containing the pollutants

Modeling the effects of evolving redox conditions on the corrosion of copper containers

International Nuclear Information System (INIS)

Kng, F.; LeNeveu, D.M.; Jobe, D.J.

1994-01-01

The corrosive environment around the containers in a Canadian nuclear fuel waste disposal vault will change over time from open-quotes warm and oxidizingclose quotes to open-quotes cool and anoxic.close quotes As the conditions change, so too will the corrosion behaviour of the containers. For copper containers, uniform corrosion and, possibly, pitting will occur during the initial aggressive phase, to be replaced by slow uniform corrosion during the long-term anoxic period. The corrosion behaviour of copper has been studied over a range of conditions representing all phases in the evolution of the vault environment. The results of these studies are summarized and used to illustrate how a model can be developed to predict the corrosion behaviour and container lifetimes over long periods of time. Lifetimes in excess of 10 6 a are predicted for 25-mm-thick copper containers under Canadian disposal conditions

Inside report on arrangement progress of an open-air pit for tools and materials of Plutonium Fuel Center, JNC

International Nuclear Information System (INIS)

Ohmura, Kenji; Sato, Shunichi; Gunji, Yasutoshi; Sawayama, Takeo; Nogami, Tetsuya; Matsuno, Kazuya; Tominaga, Setsuo; Osawa, Takayasu

1999-03-01

In the course of arranging the wasted tools and materials in the open-air pit (B-pit) of Plutonium Fuel Center, JNC, a radioactive contamination occurred on June 25, 1998, on working clothes of an operator. The B-pit was immediately set up as a temporarily radiation-controlled area and the necessary works such as disposing contaminated wastes, decontamination and surface coatings as well as cleaning have been finished on February 2, 1999. The present report describes the main procedure of actual operations, a possible cause of the contamination, and the resulting wastes from the present work amounting to about 250 drums. (Ohno, S.)

Equipment size effects on open pit mining performance

Energy Technology Data Exchange (ETDEWEB)

A. Bozorgebrahimi; R.A. Hall; M.A. Morin [University of British Columbia, Vancouver, BC (Canada). Mining Engineering Department

2005-03-01

This paper discusses the exploitation of economies of scale in open pit mining through the use of increasingly larger equipment. It presents a method adopted to evaluate the impact of increased scale on operational performance factors. The work identifies equipment size sensitive variables (ESSVs) in the mine design process that affect the performance of the production process. Data from a set of case studies show that the ESSV influence extends beyond mine production to encompass milling performance, environmental footprint and community impacts. Some ESSVs (such as reliability, tyre costs and productivity) are shown to be related to the current state of equipment technology and their effects are therefore comparable for different mines. Other ESSVs relate to the mine and deposit characteristics; their effects therefore vary from mine to mine. A detailed analytical approach, developed to model the impact of ESSVs, suggests that for truck/shovel operations, the industry may be approaching a situation of diseconomies of scale.

CENSUS AND STATISTICAL CHARACTERIZATION OF SOIL AND WATER QUALITY AT ABANDONED AND OTHER CENTRALIZED AND COMMERCIAL DRILLING-FLUID DISPOSAL SITES IN LOUISIANA, NEW MEXICO, OKLAHOMA, AND TEXAS

Energy Technology Data Exchange (ETDEWEB)

Alan R. Dutton; H. Seay Nance

2003-06-01

Commercial and centralized drilling-fluid disposal (CCDD) sites receive a portion of spent drilling fluids for disposal from oil and gas exploration and production (E&P) operations. Many older and some abandoned sites may have operated under less stringent regulations than are currently enforced. This study provides a census, compilation, and summary of information on active, inactive, and abandoned CCDD sites in Louisiana, New Mexico, Oklahoma, and Texas, intended as a basis for supporting State-funded assessment and remediation of abandoned sites. Closure of abandoned CCDD sites is within the jurisdiction of State regulatory agencies. Sources of data used in this study on abandoned CCDD sites mainly are permit files at State regulatory agencies. Active and inactive sites were included because data on abandoned sites are sparse. Onsite reserve pits at individual wells for disposal of spent drilling fluid are not part of this study. Of 287 CCDD sites in the four States for which we compiled data, 34 had been abandoned whereas 54 were active and 199 were inactive as of January 2002. Most were disposal-pit facilities; five percent were land treatment facilities. A typical disposal-pit facility has fewer than 3 disposal pits or cells, which have a median size of approximately 2 acres each. Data from well-documented sites may be used to predict some conditions at abandoned sites; older abandoned sites might have outlier concentrations for some metal and organic constituents. Groundwater at a significant number of sites had an average chloride concentration that exceeded nonactionable secondary drinking water standard of 250 mg/L, or a total dissolved solids content of >10,000 mg/L, the limiting definition for underground sources of drinking water source, or both. Background data were lacking, however, so we did not determine whether these concentrations in groundwater reflected site operations. Site remediation has not been found necessary to date for most abandoned

Using remote sensing imagery to monitoring sea surface pollution cause by abandoned gold-copper mine

Science.gov (United States)

Kao, H. M.; Ren, H.; Lee, Y. T.

2010-08-01

The Chinkuashih Benshen mine was the largest gold-copper mine in Taiwan before the owner had abandoned the mine in 1987. However, even the mine had been closed, the mineral still interacts with rain and underground water and flowed into the sea. The polluted sea surface had appeared yellow, green and even white color, and the pollutants had carried by the coast current. In this study, we used the optical satellite images to monitoring the sea surface. Several image processing algorithms are employed especial the subpixel technique and linear mixture model to estimate the concentration of pollutants. The change detection approach is also applied to track them. We also conduct the chemical analysis of the polluted water to provide the ground truth validation. By the correlation analysis between the satellite observation and the ground truth chemical analysis, an effective approach to monitoring water pollution could be established.

Post-pit optimization strategic alignment

OpenAIRE

Breed, M.F.; van Heerden, D.

2016-01-01

Successful development of projects or life-of-mine strategies requires an understanding of the relative sensitivity of value drivers such as grade, tonnage, energy costs, direct operational costs, and recoveries. For example, the results could vary significantly depending on the grade strategy, given a specific orebody amenable to open pitting. Pit optimization is a very powerful tool widely used in the industry to determine the pit shell with the most attractive value potential. Based on the...

Coal and Open-pit surface mining impacts on American Lands (COAL)

Science.gov (United States)

Brown, T. A.; McGibbney, L. J.

2017-12-01

Mining is known to cause environmental degradation, but software tools to identify its impacts are lacking. However, remote sensing, spectral reflectance, and geographic data are readily available, and high-performance cloud computing resources exist for scientific research. Coal and Open-pit surface mining impacts on American Lands (COAL) provides a suite of algorithms and documentation to leverage these data and resources to identify evidence of mining and correlate it with environmental impacts over time.COAL was originally developed as a 2016 - 2017 senior capstone collaboration between scientists at the NASA Jet Propulsion Laboratory (JPL) and computer science students at Oregon State University (OSU). The COAL team implemented a free and open-source software library called "pycoal" in the Python programming language which facilitated a case study of the effects of coal mining on water resources. Evidence of acid mine drainage associated with an open-pit coal mine in New Mexico was derived by correlating imaging spectrometer data from the JPL Airborne Visible/InfraRed Imaging Spectrometer - Next Generation (AVIRIS-NG), spectral reflectance data published by the USGS Spectroscopy Laboratory in the USGS Digital Spectral Library 06, and GIS hydrography data published by the USGS National Geospatial Program in The National Map. This case study indicated that the spectral and geospatial algorithms developed by COAL can be used successfully to analyze the environmental impacts of mining activities.Continued development of COAL has been promoted by a Startup allocation award of high-performance computing resources from the Extreme Science and Engineering Discovery Environment (XSEDE). These resources allow the team to undertake further benchmarking, evaluation, and experimentation using multiple XSEDE resources. The opportunity to use computational infrastructure of this caliber will further enable the development of a science gateway to continue foundational COAL

CopperCore, an Open Source IMS Learning Design Engine

NARCIS (Netherlands)

Vogten, Hubert

2004-01-01

The presentation gives an overview of the approach of the development programme of the OTEC department towards the development of Open Source. The CopperCore IMS Learning Design engine is described as an example of this approach.

The effect of discontinuities on the corrosion behaviour of copper canisters

International Nuclear Information System (INIS)

King, F.

2004-03-01

Discontinuities may remain in the weld region of copper canisters following the final closure welding and inspection procedures. Although the shell of the copper canister is expected to exhibit excellent corrosion properties in the repository environment, the question remains what impact these discontinuities might have on the long-term performance and service life of the canister. A review of the relevant corrosion literature has been carried out and an expert opinion of the impact of these discontinuities on the canister lifetime has been developed. Since the amount of oxidant in the repository is limited and the maximum wall penetration is expected to be 2 O/Cu(OH) 2 film at a critical electrochemical potential determines where and when pits initiate, not the presence of pit-shaped surface discontinuities. The factors controlling pit growth and death are well understood. There is evidence for a maximum pit radius for copper in chloride solutions, above which the small anodic: cathodic surface area ratio required for the formation of deep pits cannot be sustained. This maximum pit radius is of the order of 0.1-0.5 mm. Surface discontinuities larger than this size are unlikely to propagate as pits, and pits generated from smaller discontinuities will die once they reach this maximum size. Death of propagating pits will be compounded by the decrease in oxygen flux to the canister as the repository environment becomes anoxic. Surface discontinuities could impact the SCC behaviour either through their effect on the local environment or via stress concentration or intensification. There is no evidence that surface discontinuities will affect the initiation of SCC by ennoblement of the corrosion potential or the formation of locally aggressive conditions. Stress concentration at pits could lead to crack initiation under some circumstances, but the stress intensity factor for the resultant cracks, or for pre-existing crack-like discontinuities, will be smaller than the

Slope Stability Analysis of Waste Dump in Sandstone Open Pit Osielec

Science.gov (United States)

Adamczyk, Justyna; Cała, Marek; Flisiak, Jerzy; Kolano, Malwina; Kowalski, Michał

2013-03-01

This paper presents the slope stability analysis for the current as well as projected (final) geometry of waste dump Sandstone Open Pit "Osielec". For the stability analysis six sections were selected. Then, the final geometry of the waste dump was designed and the stability analysis was conducted. On the basis of the analysis results the opportunities to improve the stability of the object were identified. The next issue addressed in the paper was to determine the proportion of the mixture containing mining and processing wastes, for which the waste dump remains stable. Stability calculations were carried out using Janbu method, which belongs to the limit equilibrium methods.

The remediation of abandoned workings of a mining area in Ningxiang uranium mine

International Nuclear Information System (INIS)

Liu Yaochi; Zhou Xinghuo; Liu Bing

2004-01-01

The typical mining under buildings and river was used in a mining area of Ningxiang uranium mine. After the mining ended, 32.1% of the 2.68 m 3 abandoned workings did not fill because of limitation of the cut-and-fill mining method at that time. To remedy this, the mine used new filling methods. After the remedial action, the filling coefficient of pits reached 100%, and that of tunnels reached 86%. It can be proved by the monitoring data that the subsiding of surface has been effectively controlled at the abandoned workings

Powder-in-tube (PIT) Nb$_{3}$Sn conductors for high-field magnets

CERN Document Server

Lindenhovius, J L H; den Ouden, A; Wessel, W A J; ten Kate, H H J

2000-01-01

New Nb/sub 3/Sn conductors, based on the powder-in-tube (PIT) process, have been developed for application in accelerator magnets and high-field solenoids. For application in accelerator magnets, SMI has developed a binary 504 filament PIT conductor by optimizing the manufacturing process and adjustment of the conductor lay-out. It uniquely combines a non-copper current density of 2680 A/mm/sup 2/@10 T with an effective filament diameter of about 20 mu m. This binary conductor may be used in a 10 T, wide bore model separator dipole magnet for the LHC, which is being developed by a collaboration of the University of Twente and CERN. A ternary (Nb/7.5wt%Ta)/sub 3/Sn conductor containing 37 filaments is particularly suited for application in extremely high-field superconducting solenoids. This wire features a copper content of 43%, a non-copper current density of 217 A/mm/sup 2/@20 T and a B/sub c2/ of 25.6 T. The main issues and the experimental results of the development program of PIT Nb/sub 3/Sn conductors a...

The effects of exposure to documented open-air burn pits on respiratory health among deployers of the Millennium Cohort Study.

Science.gov (United States)

Smith, Besa; Wong, Charlene A; Boyko, Edward J; Phillips, Christopher J; Gackstetter, Gary D; Ryan, Margaret A K; Smith, Tyler C

2012-06-01

To investigate respiratory illnesses and potential open-air burn pit exposure among Millennium Cohort participants who deployed to Iraq or Afghanistan. Using multivariable logistic regression, newly reported chronic bronchitis or emphysema, newly reported asthma, and self-reported respiratory symptoms and possible burn pit exposure within 2, 3, or 5 miles were examined among Army and Air Force deployers surveyed in 2004 to 2006 and 2007 to 2008 (n = 22,844). Burn pit exposure within 3 or 5 miles was not associated with respiratory outcomes after statistical adjustment. Increased symptom reporting was observed among Air Force deployers located within 2 miles of Joint Base Balad; however, this finding was marginally significant with no evidence of trend. In general, these findings do not support an elevated risk for respiratory outcomes among personnel deployed within proximity of documented burn pits in Iraq.

Study on sand particles creep model and open pit mine landslide mechanism caused by sand fatigue liquefaction

Science.gov (United States)

Du, Dong-Ning; Wang, Lai-Gui; Zhang, Xiang-Dong; Zhang, Shu-Kun

2017-06-01

The sand particles in the sand - rock composite slope of the open pit mine occurs creep deformation and fatigue liquefaction under the action of vehicle load vibration and hydraulic gradient, which causes landslide geological disasters and it destroys the surface environment. To reveal the mechanism, a mechanics model based on the model considering the soil structural change with a new “plastic hinge” element is developed, to improve its constitutive and creep curve equations. Data from sand creep experiments are used to identify the parameters in the model and to validate the model. The results show that the mechanical model can describe the rotation progress between the sand particles, disclose the negative acceleration creep deformation stage during the third phase, and require fewer parameters while maintaining accuracy. It provides a new creep model considering rotation to analyze sand creep mechanism, which provides a theoretical basis for revealing the open pit mine landslide mechanism induced by creep deformation and fatigue liquefaction of sandy soil.

ON THE PROPAGATION OF OPEN AND COVERED PIT IN 316L STAINLESS STEEL

International Nuclear Information System (INIS)

Heurtault, Stéphane; Robin, Raphaël; Rouillard, Fabien; Vivier, Vincent

2016-01-01

Highlights: • The propagation of a single pit was investigated with a flow micro-device. • Both in depth and radial pit propagation were characterized. • The formation of a salt film in the pit was discussed. - Abstract: Pitting corrosion on stainless steel has been widely studied during the last decades, but since it is a stochastic process, it remains difficult to analyze experimentally such a phenomenon. In this work, reproducible single pits were performed on 316L steel by using an experimental setup based on the use of a glass microcapillary to locally supply chloride ions on the steel surface in order to characterize the pit propagation. This original approach allowed obtaining new results about pit propagation. Indeed, it was possible to control the presence of a metallic cap covering the pit by adjusting the experimental parameters (potential – chloride to sulfate ratio – temperature). The presence of this cover was shown to be an important issue concerning the propagation mechanism. It was also possible to study the evolution of both the pit depth and the pit diameter as a function of various parameters. Then, based on the simulation of the current densities at the pit bottom and at the pit aperture, a special attention has been paid for the investigation of the local propagation mechanism.

Group traction drive as means to increase energy efficiency of lokomotives of open-pit transport

Science.gov (United States)

Antipin, D. Ya; Izmerov, O. V.; Bishutin, S. G.; Kobishchanov, V. V.

2017-10-01

Questions of possible use of a group drive for locomotives of an open-pit transport are considered. The possibility of a significant reduction of traction costs in the case of a combination of a group traction drive with devices for the non-inertial regulation of the coefficient of friction between the wheel and the rail has been shown, and new patentable solutions have been proposed.

Optimization Of Blasting Design Parameters On Open Pit Bench A Case Study Of Nchanga Open Pits

Directory of Open Access Journals (Sweden)

Victor Mwango Bowa

2015-08-01

Full Text Available Abstract In hard rock mining blasting is the most productive excavation technique applied to fragment insitu rock to the required size for efficient loading and crushing. In order to blast the insitu rock to the desired fragment size blast design parameter such as bench height hole diameter spacing burden hole length bottom charge specific charge and rock factor are considered. The research was carried out as a practical method on Nchanga Open Pits NOP ore Bench to optimize the blasting design parameters that can yield the required fragmentation size thereby reducing the shovel loading times and maximizing efficiency of the subsequent mining unit operations such as hauling and crushing. Fragmentation characteristics such as the mean fragment size were measured by means of a digital measuring tape and predicated using the Kuznetsov equation and rock factor value of ore bench was calculated using Lilly 1986 equations by means of rock characteristics. Traditional blasting design parameters were acquired for NOP and modified using Langerfors and Sharma P.A approaches. Several blast operations were conducted using both traditional and modified blasting design parameters on the same ore bench with the same geological conditions. Loading times of the shovel and fragment sizes were obtained after the blasts from ore bench where both the traditional and modified blasting design parameters were applied. Results show that mean fragment size and loading times were reduced from 51cm and 12minutes to 22cm and 3minutes where traditional and modified blasting design parameters were applied respectively.

Natural radioactivity in lignite samples from open pit mines "Kolubara", Serbia--risk assessment.

Science.gov (United States)

Ðurašević, M; Kandić, A; Stefanović, P; Vukanac, I; Sešlak, B; Milošević, Z; Marković, T

2014-05-01

Coal as fossil fuel mainly contains naturally occurring radionuclides from the uranium and thorium series and (40)K. Use of coal, primarily in industry, as a result has dispersion of radioactive material from coal in and through air and water. The aim of this study was to determine the activity concentrations of natural radionuclides in coal samples from open pit mines "Kolubara" and to evaluate its effect on population health. The results showed that all measured and calculated values were below the limits recommended in international legislation. © 2013 Published by Elsevier Ltd.

Evaluation of groundwater pollution in a mining area using analytical solution: a case study of the Yimin open-pit mine in China.

Science.gov (United States)

Li, Tianxin; Li, Li; Song, Hongqing; Meng, Linglong; Zhang, Shuli; Huang, Gang

2016-01-01

This study focused on using analytical and numerical models to develop and manage groundwater resources, and predict the effects of management measurements in the groundwater system. Movement of contaminants can be studied based on groundwater flow characteristics. This study can be used for prediction of ion concentration and evaluation of groundwater pollution as the theoretical basis. The Yimin open-pit mine is located in the northern part of the Inner Mongolia Autonomous Region of China. High concentrations of iron and manganese are observed in Yimin open-pit mine because of exploitation and pumping that have increased the concentration of the ions in groundwater. In this study, iron was considered as an index of contamination, and the solute model was calibrated using concentration observations from 14 wells in 2014. The groundwater flow model and analytical solutions were used in this study to forecast pollution concentration and variation trend after calibration. With continuous pumping, contaminants will migrate, and become enriched, towards the wellhead in the flow direction. The concentration of the contaminants and the range of pollution increase with the flow rate increased. The suitable flow rate of single well should be open-pit for the standard value of pollution concentration.

Landslide phenomena in Dashkesan open pit mines and a rational blasting technology

Energy Technology Data Exchange (ETDEWEB)

Shrubko, S A; Kasumov, F K

1980-01-01

The reasons for the occurrence of landslides are examined, based on the stability of the surrounding rocks in the presence of a round, cylindrical slip surface. It is recommended that surveying be done to establish the boundaries of dangerous zones and to determine the locations of fracture systems. Finishing off the body of a landslide by exploding a lateral fixing is described, as is finishing off in stages, using lateral progress cycles from the top downwards. Stage blasting of a group of benches with decelaration from the top downwards is also described. A description of preventive measures taken to prevent landslide phenomena in open pit mines is given.

Mudstone depressurization behaviour in an open pit coal mine, Indonesia

Energy Technology Data Exchange (ETDEWEB)

Marchand, G.; Waterhouse, J. [Golder Associates, West Perth, WA (Australia); Crisostomo, J. [PT Adaro Indonesia, Jakarta (Indonesia)

2010-07-01

Mining activities in the Tutupan mine in Indonesia began in the mid-1990s. The open pit mine's coal seams are interbedded with fine-grained sandstones, mudstones, and carbonaceous mudstones. Slope stability analyses at the pit have integrated hydrogeology with geotechnical engineering analyses to optimize slope designs and reduce the risk of slope failure. This paper discussed the impact of mining and dewatering on mudstone depressurization. Sensors were placed at key points in the mine to obtain data related to the mudstone units. Reductions in pore pressure occurred as a result of groundwater flow away from the observed zones, increases in porosity, and increases in total porosity caused by an expansion of the rock mass as a result of drainage and hydrostatic unloading. Mudstone pore pressure trends with time were interpreted by determining the thickness of the mudstone unit, the presence or absence of known thin sandstone beds, unloading from overhead mining activities, and the position of the mudstone within the sedimentary sequence. The study showed that unloading activities have a significant impact on pore pressure in thick mudstone units, regardless of the depth, thickness, or properties of the unit. Pore pressure within high wall mudstone units typically decreased to values equivalent to the elevation of the unit where it was exposed to dips in a high wall. The dewatering of sandstone units in low walls caused a decline in pore pressure within the thick mudstone units located beneath the sandstones. Differences in primary permeabilities were attributed to greater fracturing in deeper and stronger rock units. 3 refs., 4 figs.

Newly reported lupus and rheumatoid arthritis in relation to deployment within proximity to a documented open-air burn pit in Iraq.

Science.gov (United States)

Jones, Kelly A; Smith, Besa; Granado, Nisara S; Boyko, Edward J; Gackstetter, Gary D; Ryan, Margaret A K; Phillips, Christopher J; Smith, Tyler C

2012-06-01

To assess the relationship between possible exposure to smoke from documented open-air burn pits and newly reported lupus and rheumatoid arthritis among Millennium Cohort participants who have deployed in support of operations in Iraq and Afghanistan. Prospectively assessed self-reported lupus and rheumatoid arthritis among deployers who completed both 2004-2006 and 2007-2008 questionnaires. After exclusions, more than 18,000 participants were deployed, including more than 3000 participants deployed within a 3-mile radius of a documented burn pit. After adjustment, proximity within 3 miles of a burn pit was not significantly associated with rheumatoid arthritis or lupus in general; however, one location was associated with lupus, although few cases were at this site (n = 2). Results indicate deployers potentially exposed to documented burn pits in the combined three-camp analysis were not at an elevated risk of lupus or rheumatoid arthritis.

Acute and chronic toxicity of effluent water from an abandoned uranium mine.

Science.gov (United States)

Antunes, S C; Pereira, R; Gonçalves, F

2007-08-01

Inactive or abandoned mines represent a significant source of environmental, chemical, physical, and aesthetic impact. Among concerning situations, the occurrence of abandoned or semi-abandoned mine-associated ponds (for sedimentation of solids, for effluent neutralization, or for washing the ore) is a common feature in this type of system. These ponds are a source of contamination for the groundwater resources and adjacent soils, because they lack appropriate impermeabilization. The use of this water for agriculture may also pose chronic risks to humans. In Portugal, these problems have been diagnosed and some remediation projects have been developed. The purpose of our study was to evaluate the acute and chronic toxicity of water samples collected from the aquatic system surrounding an abandoned uranium mine (Cunha Baixa, Mangualde, Central Portugal). The present study focuses on the water compartment, whose toxicity was evaluated by means of standard toxicity assays using two Daphnia species (D. longispina and D. magna). Three different ponds were used in the characterization of the aquatic system from Cunha Baixa mine: a reference pond (Ref), a mine effluent treatment pond (T), and a mine pit pond (M). Metal analyses performed in the water samples from these ponds showed values that, in some cases, were much higher than maximum recommendable values established (especially Al, Mn) by Portuguese legislation for waters for crop irrigation. Acute toxicity was only observed in the mine pit pond, with EC(50) values of 28.4% and 50.4% for D. longispina and D. magna, respectively. The significant impairment of chronic endpoints, translated in reductions in the population growth rate for both species, gives rise to concerns regarding the potential risks for aquatic zooplanktonic communities, from local receiving waters, potentially exposed to point source discharges of the treated and nontreated effluent from Cunha Baixa uranium mine.

Novel approach for extinguishing large-scale coal fires using gas-liquid foams in open pit mines.

Science.gov (United States)

Lu, Xinxiao; Wang, Deming; Qin, Botao; Tian, Fuchao; Shi, Guangyi; Dong, Shuaijun

2015-12-01

Coal fires are a serious threat to the workers' security and safe production in open pit mines. The coal fire source is hidden and innumerable, and the large-area cavity is prevalent in the coal seam after the coal burned, causing the conventional extinguishment technology difficult to work. Foams are considered as an efficient means of fire extinguishment in these large-scale workplaces. A noble foam preparation method is introduced, and an original design of cavitation jet device is proposed to add foaming agent stably. The jet cavitation occurs when the water flow rate and pressure ratio reach specified values. Through self-building foaming system, the high performance foams are produced and then infused into the blast drilling holes at a large flow. Without complicated operation, this system is found to be very suitable for extinguishing large-scale coal fires. Field application shows that foam generation adopting the proposed key technology makes a good fire extinguishment effect. The temperature reduction using foams is 6-7 times higher than water, and CO concentration is reduced from 9.43 to 0.092‰ in the drilling hole. The coal fires are controlled successfully in open pit mines, ensuring the normal production as well as the security of personnel and equipment.

DETERMINATION OF OPTIMAL CONTOURS OF OPEN PIT MINE DURING OIL SHALE EXPLOITATION, BY MINEX 5.2.3. PROGRAM

Directory of Open Access Journals (Sweden)

Miroslav Ignjatović

2013-04-01

Full Text Available By examination and determination of optimal solution of technological processes of exploitation and oil shale processing from Aleksinac site and with adopted technical solution and exploitation of oil shale, derived a technical solution that optimize contour of the newly defined open pit mine. In the world, this problem is solved by using a computer program that has become the established standard for quick and efficient solution for this problem. One of the computer’s program, which can be used for determination of the optimal contours of open pit mines is Minex 5.2.3. program, produced in Australia in the Surpac Minex Group Pty Ltd Company, which is applied at the Mining and Metallurgy Institute Bor (no. of licenses are SSI - 24765 and SSI - 24766. In this study, authors performed 11 optimization of deposit geo - models in Minex 5.2.3. based on the tests results, performed in a laboratory for soil mechanics of Mining and Metallurgy Institute, Bor, on samples from the site of Aleksinac deposits.

Open-pit coal mine production sequencing incorporating grade blending and stockpiling options: An application from an Indian mine

Science.gov (United States)

Kumar, Ashish; Chatterjee, Snehamoy

2017-05-01

Production scheduling is a crucial aspect of the mining industry. An optimal and efficient production schedule can increase the profits manifold and reduce the amount of waste to be handled. Production scheduling for coal mines is necessary to maintain consistency in the quality and quantity parameters of coal supplied to power plants. Irregularity in the quality parameters of the coal can lead to heavy losses in coal-fired power plants. Moreover, the stockpiling of coal poses environmental and fire problems owing to low incubation periods. This article proposes a production scheduling formulation for open-pit coal mines including stockpiling and blending opportunities, which play a major role in maintaining the quality and quantity of supplied coal. The proposed formulation was applied to a large open-pit coal mine in India. This contribution provides an efficient production scheduling formulation for coal mines after utilizing the stockpile coal within the incubation periods with the maximization of discounted cash flows. At the same time, consistency is maintained in the quality and quantity of coal to power plants through blending and stockpiling options to ensure smooth functioning.

75 FR 62756 - Superior National Forest, Minnesota

Science.gov (United States)

2010-10-13

... statement for the construction and operation of an open pit copper/ nickel/cobalt/precious metals mine, an... produce base and precious metals, precipitates, and flotation concentrates from ore mined at the NorthMet... construction and operation of an open pit copper/nickel/cobalt/precious metals mine in the low grade poly...

Peak particle velocity for rockbursts in underground coal mines and for shot-hole explosions in open-pit mines

Czech Academy of Sciences Publication Activity Database

Holub, Karel; Rušajová, Jana

2011-01-01

Roč. 46, č. 1 (2011), s. 104-114 ISSN 1217-8977 Institutional research plan: CEZ:AV0Z30860518 Keywords : hole-shot explosion * open-pit mine * peak particle velocity Subject RIV: DC - Siesmology, Volcanology, Earth Structure Impact factor: 0.346, year: 2011 http://www.akademiai.com/content/k3u1334gw21u4x27/

The use of geotextile tube containers for dewatering the Restigouche open pit zinc mine and settling pond basin in New Brunswick, Canada

Energy Technology Data Exchange (ETDEWEB)

Douheret [Terratube, Saint-Romuald, PQ (Canada)

2010-07-01

This PowerPoint presentation discussed the use of geotextile tube containers for the dewatering of an open pit zinc mine and settling pond in New Brunswick (NB). The zinc and lead mine closed in 1996 and will be re-opened in 2007. Remediation of the site has been challenged by severe discharge criteria for treated water, as well as by the different types of wastewater produced at the site, which is located in a mountainous area with no impermeable soil. The remediation projects include an open pit cleaning procedure where water is removed and the mine is then desludged. A wastewater treatment plant will then be installed. More than 32,000 m{sup 3} of sludge has accumulated at the bottom of the pit. The zinc content of the sludge was estimated at 2.5 ppm. The water management phase of the project will include batch treatments and the addition of 140 metric tonnes of lime to raise the pH and to precipitate metal ions. The sludge management program included the use of mechanical dewatering, the construction of a storage area, and the use of geocontainers for dewatering and temporary containment. Seventeen geotextile containers were used to reduce the zinc content of the water to less than the 250 ppb authorized by environmental agencies. The containers were changed once every 2 months. tabs., figs.

A cost comparison study of open pit mining vs. in situ assisted gravity drainage

International Nuclear Information System (INIS)

McIntosh, J.; Luhning, R.W.

1991-01-01

The twin-well steam assisted gravity drainage (SAGD) process has resulted in breakthrough technology to access previously uneconomical deep-seated oil sands reserves in Alberta, and to provide a very cost-effective and environmentally acceptable method for extracting bitumen from reserves having a minimum of 30 m overburden. In the evaluation of new or improved bitumen recovery technologies for its new North Mine, Syncrude Canada has recognized that SAGD was a potential alternate to the current open pit mining and hot water extraction process. A study was conducted to compare and evaluate bitumen recovery by the two schemes at the North Mine site, scheduled to begin operations in 1996, for the reserves under Syncrude's tailings pond, and at a new grassroots area. Study description and analysis of results are presented for the grassroots case. The assumptions and mining/recovery processes used for the mining or SAGD method are detailed and the advantages and drawbacks of each scheme are noted. Results show that the SAGD unit supply costs are projected to be proportionately lower than the corresponding open pit mining/hot water extraction (OP/X) cost, using a 20-y project life. A sensitivity analysis indicates that the SAGD process is more sensitive to natural gas costs, while the OP/X scheme is more sensitive to power costs. The SAGD process is much less labor-intensive than OP/X and has obvious advantages in terms of tailings disposal and post-mining reclamation. In addition, the underground nature of SAGD operation eliminates adverse effects of the weather on working conditions. 11 figs

Overcoming the pitfalls of abandoned mine workings in the Sydney coalfield

Energy Technology Data Exchange (ETDEWEB)

Forrester, D.; Noble, B. [AECOM, Sydney, NS (Canada)

2010-07-01

Previous coal mining activities in Sydney, Nova Scotia (NS) have included the creation of shallow, unrecorded underground coal extraction sites known as bootleg pits. The sites are a public safety hazard and can also impact groundwater flow. This paper presented an outline of the remediation strategies used to mitigate the hazards associated with the bootleg pits as part of a mine site closure and reclamation program currently being completed by the Cape Breton Corporation (ECBC). The strategies included the use of sinkhole subsidence hazard maps. Long-term visual monitoring is also being used in areas associated with sinkhole development. Larger abandoned areas have been cleared, backfilled and re-graded while including provisions for the ongoing drainage of mine waters. Gas monitoring and safety procedures were also reviewed. 2 refs., 4 figs.

Geochemical speciation and dynamic of copper in tropical semi-arid soils exposed to metal-bearing mine wastes

Energy Technology Data Exchange (ETDEWEB)

Perlatti, Fabio [Department of Environmental Technology, National Department of Mineral Production – DNPM, Rua Dr. José Lourenço, 90560115-280 Fortaleza, CE (Brazil); Graduate Course of Ecology and Natural Resources, Department of Biology, Federal University of Ceará – UFC, Building 906, 60455-760, Fortaleza, CE (Brazil); Otero, Xosé Luis; Macias, Felipe [Department of Edaphology and Agricultural Chemistry, Faculty of Biology, University of Santiago de Compostela – USC, Rúa Lope Gómez de Marzoa, s/n. Campus sur, 15782 Santiago de Compostela (Spain); Ferreira, Tiago Osório, E-mail: toferreira@usp.br [Department of Soil Science, University of São Paulo (ESALQ/USP), Av. Pádua Dias, 11, 13418-900, Piracicaba, SP (Brazil); Graduate Course of Ecology and Natural Resources, Department of Biology, Federal University of Ceará – UFC, Building 906, 60455-760, Fortaleza, CE (Brazil)

2014-12-01

The potentially hazardous effects of rock wastes disposed at open pit in three different areas (Pr: Ore processing; Wr: Waste rock and Bd: Border) of an abandoned copper mine were evaluated in this study, with emphasis on acid drainage generation, metal contamination and copper geochemical dynamics in soils. Samples of waste rock were analyzed by Energy dispersive X-ray fluorescence (XRF), scanning electron microscopy with microanalysis (SEM-EDS) and X-ray diffraction (XRD). Soil samples were analyzed to determine the total metal contents (XRF), mineralogy (XRD), pH (H2O and H2O2), organic and inorganic carbon, % of total N, S and P, particle size, and a sequential extraction procedure was used to identify the different copper fractions. As a result of the prevalence of carbonates over sulphides in the wastes, the soil pH remained close to neutral, with absence of acid mine drainage. The geochemical interaction between these mineral phases seems to be the main mechanism to release Cu{sup 2+} ions. Total Cu in soils from the Pr area reached 11,180 mg.kg{sup −1}, while in Wr and Bd areas the values reached, on average, 4683 and 1086 mg.kg{sup −1}, respectively, indicating a very high level of soil contamination. In the Pr and Wr, the Cu was mainly associated with carbonates and amorphous iron oxides. In the Bd areas, the presence of vegetation has influenced the geochemical behavior of copper by increasing the dissolution of carbonates, affecting the buffer capacity of soils against sulphide oxidation, reducing the pH levels and enhancing the proportion of exchangeable and organic bound Cu. The present findings show that the use of plants or organic amendments in mine sites with high concentration of Cu carbonate-containing wastes should be viewed with caution, as the practice may enhance the mobilization of copper to the environment due to an increase in the rate of carbonates dissolution. - Highlights: • The hazardous effects of mine waste rocks at

Limnological and fisheries investigation of the flooded open pit at the Gunnar uranium mine

International Nuclear Information System (INIS)

Tones, P.I.

1982-02-01

The Gunnar uranium mine on the north shore of Lake Athabaska was closed in 1964 and became flooded. This study describes the physical, chemical and biological characteristics of the water-filled open pit mine. Depth profiles of temperature, dissolved oxygen and specific conductivity indicated the presence of five strata in the 110 m-deep lake during the summer. Radionuclides and dissolved salts were concentrated in the deepest layer, where there was almost no dissolved oxygen and living organisms. The concentrations of heavy metals except uranium are generally very low at all depths. Surface levels of radium 226, thorium, uranium and lead 210 are low. There is no surface seepage out of the pit. Bacteria and phytoplankton populations are typical of those found in warm nutrient-rich waters; the total number of species is low, but there is a large number of individuals. No benthic species are present at the bottom or at 82.5 m. Northern pike, common suckers, and longnose suckers were caught; all appeared to be in good condition and larger than individuals of the same age in the neighbouring lakes. Radionuclide levels in their flesh were one to two orders of magnitude greater than background

Corrosion of copper and copper alloys in a basaltic repository environment

International Nuclear Information System (INIS)

Brehm, W.F.

1990-01-01

Corrosion testing done on copper and copper alloys in support of the basalt repository program is discussed. Tests were performed under anoxic conditions at 50C, 100C, 150C and 200C in the presence of a saturated basalt-bentonite packing. Tests were also performed in an air/steam mixture at temperatures between 150C and 200C. Some tests, particularly those in air/steam mixtures, were done in the presence of radiation fields of 10 2 , 10 3 or 10 4 rad/h. Exposure periods were up to 28 months. A synthetic groundwater, Grande Ronde ≠4, was used. The materials studied were ASTM B402μm·a for copper and 17 μm·a for cupronickel, but the average rates were muμm·a was obtained. The rates at longer times were less than a third of this value. Corrosion increased monotonically with time and temperature. Chalcocite (Cu 2 S) was the corrosion product at 200C. There was no detectable radiation effect, and no pitting was observed. In air/steam corrosion was uniform with no pitting. Linear corrosion was observed for pure copper. The maximum corrosion penetration after 25 months was 0.13 mm at 300C; cupronickel corroded more slowly, with a maximum penetration of 0.045mm after 25 months. Cuprite (Cu 2 O) and tenorite (CuO) were identified on cupronickel, but only Cu 2 O on copper. A pronounced radiation effect was seen at 250C, but not at 150C; the surface film morphology was different under irradiation. In the short term the presence of packing increased the corrosion rate. 5 refs

INFLUENCE OF THE TECTONIC FABRIC ON THE OPEN PIT DESING IN THE ¨ZAPREŠIČKI IVANEC¨ NEAR ZAGREB DOLOMITE QUARRY

Directory of Open Access Journals (Sweden)

Karlo Braun

1989-12-01

Full Text Available In the »Zaprešički Ivanec« dolomite open pit near Zagreb, exploitation is carried out according to data obtained by analysis of the tectonic fabric of the rock massif, by measurement of the longitudinal seismic waves velocity, and effects of the seismic waves provoked blasting. In this article the fundamental data obtained by structural analysis and measurements with their influence on the pit design and the optimization of blasting conditions, are reviewed. Results of the longtime exploitation verify such complex aproach to deposit work-out (the paper is published in Croatian.

Application of 3D Laser Scanning Technology in Inspection and Dynamic Reserves Detection of Open-Pit Mine

Science.gov (United States)

Hu, Zhumin; Wei, Shiyu; Jiang, Jun

2017-10-01

The traditional open-pit mine mining rights verification and dynamic reserve detection means rely on the total station and RTK to collect the results of the turning point coordinates of mining surface contours. It resulted in obtaining the results of low precision and large error in the means that is limited by the traditional measurement equipment accuracy and measurement methods. The three-dimensional scanning technology can obtain the three-dimensional coordinate data of the surface of the measured object in a large area at high resolution. This paper expounds the commonly used application of 3D scanning technology in the inspection and dynamic reserve detection of open mine mining rights.

Open-cellular copper structures fabricated by additive manufacturing using electron beam melting

International Nuclear Information System (INIS)

Ramirez, D.A.; Murr, L.E.; Li, S.J.; Tian, Y.X.; Martinez, E.; Martinez, J.L.; Machado, B.I.; Gaytan, S.M.; Medina, F.; Wicker, R.B.

2011-01-01

Highlights: → Relative stiffness versus relative density measurements for reticulated mesh and stochastic open cellular copper were shown to follow the Gibson-Ashby foam model. → Microstructures for the mesh struts and foam ligaments illustrated a propensity of copper oxide precipitates which provided structural hardness and strength. → These components, fabricated by electron beam melting, exhibit interesting prospects for specialized, complex heat-transfer devices. - Abstract: Cu reticulated mesh and stochastic open cellular foams were fabricated by additive manufacturing using electron beam melting. Fabricated densities ranged from 0.73 g/cm 3 to 6.67 g/cm 3 . The precursor Cu powder contained Cu 2 O precipitates and the fabricated components contained arrays of Cu 2 O precipitates and interconnected dislocation microstructures having average spacings of ∼2 μm, which provide hardness values ∼75% above commercial Cu products. Plots of stiffness (Young's modulus) versus density and relative stiffness versus relative density were in very close agreement with the Gibson-Ashby model for open cellular foams. These open cellular structure components exhibit considerable potential for novel, complex, multi-functional electrical and thermal management systems, especially complex, monolithic heat exchange devices.

A mineral quantification method for wall rocks at open pit mines, and application to the Martha Au-Ag mine, Waihi, New Zealand

International Nuclear Information System (INIS)

Castendyk, Devin N.; Mauk, Jeffrey L.; Webster, Jenny G.

2005-01-01

Pit lakes that result from open pit mining are potential water resources or potential environmental problems, depending on lake water quality. Wall rock mineralogy can affect lake chemistry if surface water inputs and/or groundwater inputs and/or lake water in contact with submerged wall rocks react with the wall rock minerals. This study presents a mineral quantification method to measure the distribution and concentration of wall rock minerals in open pit mines, and applies the method to the Martha epithermal Au-Ag mine, Waihi, New Zealand. Heterogeneous ore deposits, like Martha, require a large number of wall rock samples to accurately define mineral distributions. X-ray diffraction analyses of 125 wall rock samples identified the most abundant minerals in the wall rocks as quartz, adularia, albite, illite, chlorite, kaolinite, pyrite and calcite. Distribution maps of these minerals defined 8 relatively homogenous areas of wall rock referred to as 'mineral associations': weakly-altered, propylitic, fresh-argillic, weathered-argillic, oxidized, potassic, quartz veins, and post-mineralization deposits. X-ray fluorescence, Leco furnace, and neutron activation analyses of 46 representative samples produced the geochemical dataset used to assign quantities of elements to observed minerals, and to calculate average mineral concentrations in each association. Thin-section petrography and calcite concentrations from Sobek acid-digestions confirm the calculated mineralogy, providing validation for the method. Calcite and pyrite concentrations allowed advanced acid-base accounting for each mineral association, identifying 3 potential acid-producing associations and one potential acid-neutralizing association. The results target areas, where detailed hydrologic and kinetic tests would be valuable in the next stage of pit lake evaluation. Detailed understanding of wall rock mineralogy will help strengthen predictions of pit lake water quality

A mineral quantification method for wall rocks at open pit mines, and application to the Martha Au-Ag mine, Waihi, New Zealand

Energy Technology Data Exchange (ETDEWEB)

Castendyk, Devin N. [Environmental Science, SGES, University of Auckland, Tamaki Campus, Private Bag 92019, Auckland (New Zealand)]. E-mail: d.castendyk@auckland.ac.nz; Mauk, Jeffrey L. [Geology Department, University of Auckland, Private Bag 92019, Auckland (New Zealand); Webster, Jenny G. [Environmental Science, SGES, University of Auckland, Tamaki Campus, Private Bag 92019, Auckland (New Zealand)

2005-01-01

Pit lakes that result from open pit mining are potential water resources or potential environmental problems, depending on lake water quality. Wall rock mineralogy can affect lake chemistry if surface water inputs and/or groundwater inputs and/or lake water in contact with submerged wall rocks react with the wall rock minerals. This study presents a mineral quantification method to measure the distribution and concentration of wall rock minerals in open pit mines, and applies the method to the Martha epithermal Au-Ag mine, Waihi, New Zealand. Heterogeneous ore deposits, like Martha, require a large number of wall rock samples to accurately define mineral distributions. X-ray diffraction analyses of 125 wall rock samples identified the most abundant minerals in the wall rocks as quartz, adularia, albite, illite, chlorite, kaolinite, pyrite and calcite. Distribution maps of these minerals defined 8 relatively homogenous areas of wall rock referred to as 'mineral associations': weakly-altered, propylitic, fresh-argillic, weathered-argillic, oxidized, potassic, quartz veins, and post-mineralization deposits. X-ray fluorescence, Leco furnace, and neutron activation analyses of 46 representative samples produced the geochemical dataset used to assign quantities of elements to observed minerals, and to calculate average mineral concentrations in each association. Thin-section petrography and calcite concentrations from Sobek acid-digestions confirm the calculated mineralogy, providing validation for the method. Calcite and pyrite concentrations allowed advanced acid-base accounting for each mineral association, identifying 3 potential acid-producing associations and one potential acid-neutralizing association. The results target areas, where detailed hydrologic and kinetic tests would be valuable in the next stage of pit lake evaluation. Detailed understanding of wall rock mineralogy will help strengthen predictions of pit lake water quality.

Copper-catalyzed asymmetric ring opening of oxabicyclic alkenes with organolithium reagents

NARCIS (Netherlands)

Bos, Pieter H.; Rudolph, Alena; Pérez, Manuel; Fañanás-Mastral, Martín; Harutyunyan, Syuzanna R.; Feringa, Bernard

2012-01-01

A highly efficient method is reported for the asymmetric ring opening of oxabicyclic alkenes with organolithium reagents. Using a copper/chiral phosphoramidite complex together with a Lewis acid (BF3·OEt2), full selectivity for the anti isomer and excellent enantioselectivities were obtained for the

Groundwater age, mixing and flow rates in the vicinity of large open pit mines, Pilbara region, northwestern Australia

Science.gov (United States)

Cook, Peter; Dogramaci, Shawan; McCallum, James; Hedley, Joanne

2017-01-01

Determining groundwater ages from environmental tracer concentrations measured on samples obtained from open bores or long-screened intervals is fraught with difficulty because the sampled water represents a variety of ages. A multi-tracer technique (Cl, 14C, 3H, CFC-11, CFC-12, CFC-113 and SF6) was used to decipher the groundwater ages sampled from long-screened production bores in a regional aquifer around an open pit mine in the Pilbara region of northwest Australia. The changes in tracer concentrations due to continuous dewatering over 7 years (2008-2014) were examined, and the tracer methods were compared. Tracer concentrations suggest that groundwater samples are a mixture of young and old water; the former is inferred to represent localised recharge from an adjacent creek, and the latter to be diffuse recharge. An increase in 14C activity with time in wells closest to the creek suggests that dewatering of the open pit to achieve dry mining conditions has resulted in change in flow direction, so that localised recharge from the creek now forms a larger proportion of the pumped groundwater. The recharge rate prior to development, calculated from a steady-state Cl mass balance, is 6 mm/y, and is consistent with calculations based on the 14C activity. Changes in CFC-12 concentrations with time may be related to the change in water-table position relative to the depth of the well screen.

Corrosion of the copper canister in the repository environment

Energy Technology Data Exchange (ETDEWEB)

Hermansson, H.P.; Eriksson, Sture [Studsvik Material AB, Nykoeping (Sweden)

1999-12-01

The present report accounts for studies on copper corrosion performed at Studsvik Material AB during 1997-1999 on commission by SKI. The work has been focused on localised corrosion and electrochemistry of copper in the repository environment. The current theory of localised copper corrosion is not consistent with recent practical experiences. It is therefore desired to complete and develop the theory based on knowledge about the repository environment and evaluations of previous as well as recent experimental and field results. The work has therefore comprised a thorough compilation and up-date of literature on copper corrosion and on the repository environment. A selection of a 'working environment', defining the chemical parameters and their ranges of variation has been made and is used as a fundament for the experimental part of the work. Experiments have then been performed on the long-range electrochemical behaviour of copper in selected environments simulating the repository. Another part of the work has been to further develop knowledge about the thermodynamic limits for corrosion in the repository environment. Some of the thermodynamic work is integrated here. Especially thermodynamics for the system Cu-Cl-H-O up to 150 deg C and high chloride concentrations are outlined. However, there is also a rough overview of the whole system Cu-Fe-Cl-S-C-H-O as a fundament for the discussion. Data are normally accounted as Pourbaix diagrams. Some of the conclusions are that general corrosion on copper will probably not be of significant importance in the repository as far as transportation rates are low. However, if such rates were high, general corrosion could be disastrous, as there is no passivation of copper in the highly saline environment. The claim on knowledge of different kinds of localised corrosion and pitting is high, as pitting damages can shorten the lifetime of a canister dramatically. Normal pitting can happen in oxidising environment, but

Corrosion of the copper canister in the repository environment

International Nuclear Information System (INIS)

Hermansson, H.P.; Eriksson, Sture

1999-12-01

The present report accounts for studies on copper corrosion performed at Studsvik Material AB during 1997-1999 on commission by SKI. The work has been focused on localised corrosion and electrochemistry of copper in the repository environment. The current theory of localised copper corrosion is not consistent with recent practical experiences. It is therefore desired to complete and develop the theory based on knowledge about the repository environment and evaluations of previous as well as recent experimental and field results. The work has therefore comprised a thorough compilation and up-date of literature on copper corrosion and on the repository environment. A selection of a 'working environment', defining the chemical parameters and their ranges of variation has been made and is used as a fundament for the experimental part of the work. Experiments have then been performed on the long-range electrochemical behaviour of copper in selected environments simulating the repository. Another part of the work has been to further develop knowledge about the thermodynamic limits for corrosion in the repository environment. Some of the thermodynamic work is integrated here. Especially thermodynamics for the system Cu-Cl-H-O up to 150 deg C and high chloride concentrations are outlined. However, there is also a rough overview of the whole system Cu-Fe-Cl-S-C-H-O as a fundament for the discussion. Data are normally accounted as Pourbaix diagrams. Some of the conclusions are that general corrosion on copper will probably not be of significant importance in the repository as far as transportation rates are low. However, if such rates were high, general corrosion could be disastrous, as there is no passivation of copper in the highly saline environment. The claim on knowledge of different kinds of localised corrosion and pitting is high, as pitting damages can shorten the lifetime of a canister dramatically. Normal pitting can happen in oxidising environment, but there is

Use of tracers to quantify subsurface flow through a mining pit.

Science.gov (United States)

Schladow, S Geoffrey; Clark, Jordan F

2008-12-01

Three independent tracer experiments were conducted to quantify the through-flow of water from Herman Pit, an abandoned mercury (Hg) mine pit adjacent to Clear Lake, California, USA. The tracers used were Rhodamine-WT, sulfur hexafluoride, and a mixture of sulfur hexafluoride and neon-22. The tracers were injected into Herman Pit, a generally well-mixed water body of approximately 81,000 m2, and the concentrations were monitored in the mine pit, observation wells, and the lake for 2-3 months following each injection. The results for all three experiments showed that the tracer arrived at certain observation wells within days of injection. Comparing all the well data showed a highly heterogeneous response, with a small number of wells showing this near-instantaneous response and others taking months before the tracer was detectable. Tracer was also found in the lake on four occasions over a one-month period, too few to infer any pattern but sufficient to confirm the connection of the two water bodies. Using a simple mass balance model it was possible to determine the effective loss rate through advection for each of the tracers and with this to estimate the through-flow rate. The through-flow rate for all three experiments was approximately 630 L/s, at least 1-2 orders of magnitude larger than previous estimates, all of which had been based on geochemical inferences or other indirect measures of the pit through-flow.

Development of an on-line coal quality management system in a lignite open pit mine in Serbia

Energy Technology Data Exchange (ETDEWEB)

Zimmer, B. [Montan Bildungs-und Entwicklungsgesellschaft mbH, Theiben, (Germany)

2010-07-01

This paper presented a study regarding the development of a coal quality management system (CQMS) for two open pit mines located in Serbia called Tamnava West and Veliki Crljeni. The study was based on on-line measurements, and was commissioned by the public energy corporation Elektroprivreda Srbjie. The purpose of the study was to develop a CQMS that met the quality requirements of the power plants by implementing a rigorous exploration, production planning, and production monitoring system in order to control the production according to certain quality parameters. The paper provided general information and described the initial situation. It also presented an analysis of the necessity to introduce a production monitoring and control system. The setup and layout of a production monitoring and control system based on on-line measurements were outlined, with particular reference to the determination of input parameters for every excavator for the tracking of masses; the simulation of mass tracking and summation of the masses at the transfer points towards the major conveyor; and the monitoring of the output and control of the mass flow according to determined limit values. Recommendations for implementation were also discussed. It was concluded that the newly developed CQMS at Tamnava West open pit mine could be classified as uncomplicated with regard to the quality parameters to be controlled, since currently only calorific value was being controlled. 5 refs., 8 figs.

The use of vibration monitoring to record the blasting works impact on buildings surrounding open-pit mines

Directory of Open Access Journals (Sweden)

Sołtys Anna

2018-01-01

Full Text Available Environmental protection law and geological and mining law require the mineral mining plant to protect its surroundings from the effects of mining operations. This also applies to the negative impact of vibrations induced by blasting works on people and construction facilities. Effective protection is only possible if the level of this impact is known, therefore it is necessary to record it. The thesis formulated in this way has been and continues to be the guiding principle of the research works carried out in the AGH Laboratory of Blasting Work and Environmental Protection. As a result of these works are procedures for conducting preventive activities by open-pit mines in order to minimize the impact of blasting on facilities in the surrounding area. An important element of this activity is the monitoring of vibrations in constructions, which is a source of knowledge for excavation supervisors and engineers performing blasting works, thus contributing to raising the awareness of the responsible operation of the mining plant. Developed in the Laboratory of the Mine's Vibration Monitoring Station (KSMD, after several modernizations, it became a fully automated system for monitoring and recording the impact of blasting works on the surrounding environment. Currently, there are 30 measuring devices in 10 open-pit mines, and additional 8 devices are used to provide periodic measurement and recording services for the mines concerned.

The use of vibration monitoring to record the blasting works impact on buildings surrounding open-pit mines

Science.gov (United States)

Sołtys, Anna; Pyra, Józef; Winzer, Jan

2018-04-01

Environmental protection law and geological and mining law require the mineral mining plant to protect its surroundings from the effects of mining operations. This also applies to the negative impact of vibrations induced by blasting works on people and construction facilities. Effective protection is only possible if the level of this impact is known, therefore it is necessary to record it. The thesis formulated in this way has been and continues to be the guiding principle of the research works carried out in the AGH Laboratory of Blasting Work and Environmental Protection. As a result of these works are procedures for conducting preventive activities by open-pit mines in order to minimize the impact of blasting on facilities in the surrounding area. An important element of this activity is the monitoring of vibrations in constructions, which is a source of knowledge for excavation supervisors and engineers performing blasting works, thus contributing to raising the awareness of the responsible operation of the mining plant. Developed in the Laboratory of the Mine's Vibration Monitoring Station (KSMD), after several modernizations, it became a fully automated system for monitoring and recording the impact of blasting works on the surrounding environment. Currently, there are 30 measuring devices in 10 open-pit mines, and additional 8 devices are used to provide periodic measurement and recording services for the mines concerned.

Geomechanical Assessments of Simultaneous Operation in the Case of Transition from Open Pit to Underground Mine in Vietnam

Science.gov (United States)

Niedbalski, Zbigniew; Nguyen, Phu Minh Vuong; Widzyk-Capehart, Eleonora

2018-03-01

Nowadays, for a number of reasons, many open pit mines are considering a transition from Open Pit (OP) to Underground (UG) to remain competitive. In OP-UG transition, UG operation is operated simultaneously with the OP operation for a certain period of time. Guidelines for the simultaneous operation of OP and UG are very difficult to establish, as there are very few case studies available. Yet, because of the OP-UG interactions; the operation has a higher safety, technical and management requirements than the OP or UG methods when considered separately. In Vietnam, Cao Son is one of many OP mines, which decided to change the operational system from OP to UG. Simultaneous operation started in 2015 and will be conducted until 2030 when the OP mine Cao Son ends its mining activities. In this paper, selected geomechanical considerations of the simultaneous operation are presented. A number of numerical modelling calculations using finitedifference software with code FLAC were carried out for calibration process, slope stability analysis and the OP-UG interaction analysis for the Cao Son - Khe Cham II-IV mine. Based on the results obtained from numerical modelling, the geomechanical assessments of simultaneous operation Cao Son - Khe Cham II-IV are discussed in this paper.

Pit membranes of Ephedra resemble gymnosperms more than angiosperms

Science.gov (United States)

Roland Dute; Lauren Bowen; Sarah Schier; Alexa Vevon; Troy Best; Maria Auad; Thomas Elder; Pauline Bouche; Steven Jansen

2014-01-01

Bordered pit pairs of Ephedra species were characterized using different types of microscopy. Pit membranes contained tori that did not stain for lignin. SEM and AFM views of the torus surface showed no plasmodesmatal openings, but branched, secondary plasmodesmata were occasionally noted using TEM in conjunction with ultrathin sections. The margo consisted of radial...

Report on the survey of abandoned uraniferous lignite mines in southwestern North Dakota

International Nuclear Information System (INIS)

Lyon, R.J.; Prochaska, D.; Burgess, J.L.; Patrick, D.

1986-03-01

A radiation survey was conducted in October 1983 as part of the proposed reclamation plan of abandoned uraniferous lignite mines in southwestern North Dakota. The survey was made to determine the extent of contamination caused by mining operations in the 1960's. Radiation measurements were made and soil samples were taken at approximately 300 locations around six mine sites comprising eleven lignite mine pits. Toxic element analysis was also done on 50 of the soil samples

The public health effects of abandoned coal mine workings on residents in South Wellington, Nanaimo

Energy Technology Data Exchange (ETDEWEB)

Biagioni, K [Victoria Univ., BC (Canada)

2005-07-01

Abandoned coal mine groundwater frequently contains depressed pH levels and elevated levels of hydrogen sulphide, iron, aluminium and nitrates. Abandoned coal mine groundwater is also usually high in copper, zinc, mercury, and lead. Groundwater from abandoned mines can seriously affect public health through the discharge of non-point source pollution. This paper presents information on a research project regarding the possible impacts of abandoned coal mines and its effects on groundwater as it relates to the health of residents in South Wellington, Nanaimo, British Columbia. The purpose of the project is to determine which illnesses are more common in South Wellington, Nanaimo and in the control area. The paper provides a discussion of the Nanaimo coal field and three major seams; the Wellington, Newcastle and Douglas which are most likely to have a significant impact on groundwater in South Wellington. 27 refs.

The public health effects of abandoned coal mine workings on residents in South Wellington, Nanaimo

International Nuclear Information System (INIS)

Biagioni, K.

2005-01-01

Abandoned coal mine groundwater frequently contains depressed pH levels and elevated levels of hydrogen sulphide, iron, aluminium and nitrates. Abandoned coal mine groundwater is also usually high in copper, zinc, mercury, and lead. Groundwater from abandoned mines can seriously affect public health through the discharge of non-point source pollution. This paper presents information on a research project regarding the possible impacts of abandoned coal mines and its effects on groundwater as it relates to the health of residents in South Wellington, Nanaimo, British Columbia. The purpose of the project is to determine which illnesses are more common in South Wellington, Nanaimo and in the control area. The paper provides a discussion of the Nanaimo coal field and three major seams; the Wellington, Newcastle and Douglas which are most likely to have a significant impact on groundwater in South Wellington. 27 refs

Near-field microwave detection of corrosion precursor pitting under thin dielectric coatings in metallic substrate

International Nuclear Information System (INIS)

Hughes, D.; Zoughi, R.; Austin, R.; Wood, N.; Engelbart, R.

2003-01-01

Detection of corrosion precursor pitting on metallic surfaces under various coatings and on bare metal is of keen interest in evaluation of aircraft fuselage. Near-field microwave nondestructive testing methods, utilizing open-ended rectangular waveguides and coaxial probes, have been used extensively for detection of surface flaws in metals, both on bare metal and under a dielectric coating. This paper presents the preliminary results of using microwave techniques to detect corrosion precursor pitting under paint and primer, applique and on bare metal. Machined pits of 500 μm diameter were detected using open-ended rectangular waveguides at V-Band under paint and primer and applique, and on bare metal. Using coaxial probes, machined pits with diameters down to 150 μm on bare metal were also detected. Relative pit size and density were shown on a corrosion-pitted sample using open-ended rectangular waveguides at frequencies of 35 GHz to 70 GHz. The use of Boeing's MAUS TM scanning systems provided improved results by alleviating standoff variation and scanning artifact. Typical results of this investigation are also presented

The legal framework for wellsite abandonment and reclamation in Alberta

International Nuclear Information System (INIS)

Gilmour, B.S.

1997-01-01

The legislative framework for wellsite reclamation in Alberta was discussed. The legal requirements that impact on wellsite abandonment and reclamation, with emphasis on the Oil and Gas Conservation Act (OGCA) and the Environmental Protection and Enhancement Act (EPEA) were described. In 1994, the Orphan Well fund was established to ensure that wells are properly abandoned in those cases where participants are insolvent. The fund is financed by the petroleum industry. The regulatory requirements for wellsite abandonment are found in the OGCA and the Well Abandonment Guide 20 which provides explicit procedures for both open-hole and cased-hole abandonment. Liability for contaminated sites exists under the contaminated sites provision of the EPEA. Amendments to the OGCA provide for more supervision over licence transfers and the granting of licences to first-time licensees

The Upper Miocene Lake Pannon marl from the Filijala Open Pit (Beočin, northern Serbia: New geological and paleomagnetic data

Directory of Open Access Journals (Sweden)

Ganić Meri

2010-01-01

Full Text Available This work presents major lithological, structural, paleontological and paleomagnetic characteristics of the Upper Miocene Pannonian marl in the Filijala Open Pit of the La Farge Cement Plant near Beočin, northern Serbia. Pannonian marl lies between the underlying heterogeneous Sarmatian deposits and the overlying set of Pontian sand beds and Quaternary sediments. The open pit is located on the NE range of Fruška Gora, a horst structure with a core of Paleozoic, Mesozoic and Paleogene rocks in a complex structural pattern. Pannonian sediments, which are part of a younger structural stage, deposited on the horst limbs. The Pannonian marl strata dip at angles from 12° to 26° (to the NNW, forming a monocline. The strata deformations are a consequence of radial tectonics and are a potential source of landslides. The many mollusks (7 gastropod and 9 bivalve species and ostracodes (27 species and their biostratigraphical position indicate marl deposition throughout the Pannonian age. A paleomagnetic investigation established that the marl has inconsistent remanent magnetization (with bad statistical parameters, which originates from neoformed magnetite.

Copper in the sediment and sea surface microlayer near a fallowed, open-net fish farm.

Science.gov (United States)

Loucks, Ronald H; Smith, Ruth E; Fisher, Clyde V; Fisher, E Brian

2012-09-01

Sediment and sea surface microlayer samples near an open-net salmon farm in Nova Scotia, were analysed for copper. Copper is a constituent of the feed and is an active ingredient of anti-foulants. The salmon farm was placed in fallow after 15 years of production. Sampling was pursued over 27 months. Elevated copper concentrations in the sediments indicated the farm site as a source. Bubble flotation due to gas-emitting sediments from eutrophication is a likely process for accumulating copper in the sea surface microlayer at enriched concentrations. Elevated and enriched concentrations in the sea surface microlayer over distance from the farm site led, as a result of wind-drift, to an enlarged farm footprint. The levels of copper in both sediments and sea surface microlayer exceeded guidelines for protection of marine life. Over the 27 months period, copper levels persisted in the sediments and decreased gradually in the sea surface microlayer. Copyright © 2012 Elsevier Ltd. All rights reserved.

An Open Pit Nanofluidic Tool: Localized Chemistry Assisted by Mesoporous Thin Film Infiltration.

Science.gov (United States)

Mercuri, Magalí; Pierpauli, Karina A; Berli, Claudio L A; Bellino, Martín G

2017-05-17

Nanofluidics based on nanoscopic porous structures has emerged as the next evolutionary milestone in the construction of versatile nanodevices with unprecedented applications. However, the straightforward development of nanofluidically interconnected systems is crucial for the production of practical devices. Here, we demonstrate that spontaneous infiltration into supramolecularly templated mesoporous oxide films at the edge of a sessile drop in open air can be used to connect pairs of landmarks. The liquids from the drops can then join through the nanoporous network to guide a localized chemical reaction at the nanofluid-front interface. This method, here named "open-pit" nanofluidics, allows mixing reagents from nanofluidically connected droplet reservoirs that can be used as reactors to conduct reactions and precipitation processes. From the fundamental point of view, the work contributes to unveiling subtle phenomena during spontaneous infiltration of fluids in bodies with nanoscale dimensions such as the front broadening effect and the oscillatory behavior of the infiltration-evaporation front. The approach has distinctive advantages such as easy fabrication, low cost, and facility of scaling up for future development of ultrasensitive detection, controlled nanomaterial synthesis, and novel patterning methods.

Estimating the effects of Technology and Depletion on the Real Price of Copper in the U. S. Using a Cointegration Approach

Energy Technology Data Exchange (ETDEWEB)

Bunuel, M.

2001-07-01

The effects of technology and depletion on U. S. copper scarcity- as measured by real price can be estimated explicitly using econometrics, rather than assuming the their combined effect is implicit in a quadratic trend. The two most relevant cost-decreasing technologies-black-caving and open-pit mining and leaching and solvent extraction-electrowinning (SX-EW)-are proxied by their rate of diffusion. Depletion is proxied by average yield. Since these proxies and real price contain a unit root. Johansen's maximum-likelihood estimation procedure is used to test for the number of cointegrating relations, and estimate a vector autoregressive model from which a price equation in error-correction form is derived. A unique cointegrating relation without a trend is found, which supports the hypothesis that the real price of copper has no scarcity-rent component if we believe that this components should be modeled as a trend. The cointegrating relation loads into the price equation, and the convergence towards the long-run equilibrium is almost instantaneous. The estimated combined effect of physical depletion and technology on the U. S. real price of copper shows that the diffusion of block-caving and open-pit mining technologies off set the effect on price of the decline in average yield until the end of the thirties. From 1938 to 1976, the combined effect was slightly positive, and markedly and continuously negative thereafter, as a result of the introduction of leaching and SX-EW technologies, and the stabilization and even increase of average yield. (Author)

Air quality status of an open pit mining area in India.

Science.gov (United States)

Chaulya, S K

2005-06-01

This investigation presents the assessment of ambient air quality carried out at an open pit coal mining area in Orissa state of India. The 24-h average concentrations of suspended particulate matter (SPM), respirable particulate matter (RPM, particles of less than 10 microm aerodynamic diameter), sulphur dioxide (SO2) and oxides of nitrogen (NO(x)) were determined at regular interval throughout one year at 13 monitoring stations in residential area and four stations in mining/industrial area. During the study period, the 24-h and annual average SPM and RPM concentrations exceeded the respective standards set in the Indian ambient air quality standard (NAAQS) protocol in most of the residential and industrial areas. However, the 24-h and annual average concentrations of SO2 and NO(x) were well within the prescribed limit of the NAAQS in both residential and industrial areas. A management strategy is formulated for effective control of particulate matter at source and other mitigative measures are recommended including implementation of green belts around the sensitive areas.

Short-term scheduling of an open-pit mine with multiple objectives

Science.gov (United States)

Blom, Michelle; Pearce, Adrian R.; Stuckey, Peter J.

2017-05-01

This article presents a novel algorithm for the generation of multiple short-term production schedules for an open-pit mine, in which several objectives, of varying priority, characterize the quality of each solution. A short-term schedule selects regions of a mine site, known as 'blocks', to be extracted in each week of a planning horizon (typically spanning 13 weeks). Existing tools for constructing these schedules use greedy heuristics, with little optimization. To construct a single schedule in which infrastructure is sufficiently utilized, with production grades consistently close to a desired target, a planner must often run these heuristics many times, adjusting parameters after each iteration. A planner's intuition and experience can evaluate the relative quality and mineability of different schedules in a way that is difficult to automate. Of interest to a short-term planner is the generation of multiple schedules, extracting available ore and waste in varying sequences, which can then be manually compared. This article presents a tool in which multiple, diverse, short-term schedules are constructed, meeting a range of common objectives without the need for iterative parameter adjustment.

Getting cold feet?: Why health care mergers are abandoned.

Science.gov (United States)

Roos, Anne-Fleur; Postma, Jeroen

2016-01-01

Despite the frequent occurrence and sizeable consequences of merger abandonment in other sectors, there is no thorough understanding of merger abandonment in health care. The purpose of this study is to improve the understanding of determinants of health care merger abandonment. On the basis of the literature on merger abandonment, we formulated a framework on potential determinants of health care merger abandonment. We then constructed a survey that was sent to 70% of all executives of Dutch health care organizations (response rate = 35%, n = 291). We provide descriptive overviews of open, multiple-response, and multiple-choice questions on merger abandonment and use chi-square tests and Fisher's exact tests to test whether abandoned and completed merger processes differ. About 62% of the respondents were involved in at least one merger process during the period of 2005-2012. Thirty-eight percent of these respondents reported that their last merger case ended prematurely (n = 53). The most frequently mentioned determinants of merger abandonment are changing insights on the desirability and feasibility during merger processes, incompatibilities between executives, and insufficient support for the merger from internal stakeholders. We did not find significant relationships between merger abandonment and executives' previous merger experience, degree of organizational diversification, health care sector, size differences, or other organizational differences. Our findings partially confirm results from previous studies, especially with regard to the importance of changing insights and incompatibilities between the involved executives in merger abandonment. We also find that pressure from internal stakeholders, particularly nonexecutive directors, and distrust, fear, and animosity play an important role in merger abandonment. To minimize the organizational and societal costs of abandoned mergers, we advise executives who engage in mergers to construct backup plans with

Effect of heat treatment on pitting corrosion of austenitic Cr-Ni-Mo steels in sodium chloride solution

International Nuclear Information System (INIS)

Stefec, R.; Franz, F.; Holecek, A.

1979-01-01

The pitting corrosion resistance of Cr17Ni12Mo2,5 type steel under potentiostatic polarization in a sodium chloride solution is adversely affected by previous annealing. The data obtained were systematically dependent on annealing temperature, time and surface roughness. The corrosion current, the number of pits or the mean area of pit opening and the corrosion rate within the pits were increased by previous annealing at 550 to 750 0 C for 1-100 hrs. The highest corrosion rate estimated corresponded to heat treatments provoking severe sensitization to intergranular corrosion. The paercentage area of corrosion pit openings and the estimated pit penetration rates were several times higher for as-machined than for polished surfaces. It can be assumed that pitting corrosion is little affected by the carbon content and that molybdenum depletion of grain-boundary zones is responsible for the reduced pitting resistance of annealed steels. (orig./HP) [de

Application of Surpac and Whittle Software in Open Pit Optimisation ...

African Journals Online (AJOL)

Michael

2015-06-01

Jun 1, 2015 ... The deposit has undergone intense weathering, forming an oxidised gold deposit ... total of 82 optimal pit outlines were generated using the 3D Lerchs-Grossmann algorithm. ... are also widely accepted in the mining industry.

Pitting corrosion of zirconium in aqueous solution

International Nuclear Information System (INIS)

El Shayeb, H.A.; Abd El Wahab, F.M.; Abd Elk Meguid, E.A.

1994-01-01

The open circuit potentials of the Zr electrode are followed as a function of time in various aqueous solutions till attainment of steady state values.The results are discussed on the basis of oxide film thickening and repair. Pitting corrosion of Zr was examined in chloride solutions using the potentiodynamic technique. The effect of some inorganic and organic additives was also investigated for inhibiting the pitting corrosion of Zr and the relative performance is presented and discussed. (author). 21 refs., 6 figs., 1 tab

Herniation pits of the femur neck: incidence and radiologic findings

International Nuclear Information System (INIS)

Cho, Jae Hyun; Suh, Jin Suk; Lee, Hye Yeon

1994-01-01

In order to assess the incidence and radiologic findings of herniation pit of the femur neck in Korean. In 152 macerated femurs of 88 cadavers, and randomly selected 115 hips of 70 patients, the presence of herniation pit was determined by using fluoroscopy and radiography. It was then examined by CT for inspection of overlying surface and its opening was confirmed by inserting thin steal wire under the fluoroscopic guidance. Seventeen herniation pits in 15 macerated femurs of 13 cadavers were noted. (14.8%, 13/88). Two of 13 individuals showed bilaterality. All lesions were found only in males. Six herniation pit in 6 femurs of 6 patients (8.6%, 6/70) were also noted. All lesions were on anterosuperior aspect of femur neck. Plain radiographs of macerated femurs revealed well marginated and thin sclerosis in 15 lesions. Of all 23 lesions, CT showed cortical breakdown in 3, and overlying cortical thickening in 8. In 15 macerated femurs, roughed area of cortex was found in anterosuperior aspect of femur in all cases, and tiny openings(diameter less than 1 mm) related to cystic lesions were confirmed in 9 lesions. The incidence of herniation pits was 14.8% in 88 cadaver, and 8.6% in 70 patients. All were males

Modeling and management of pit lake water chemistry 1: Theory

International Nuclear Information System (INIS)

Castendyk, D.N.; Eary, L.E.; Balistrieri, L.S.

2015-01-01

Highlights: • Review of pit lake literature in the context of pit lake predictions. • Review of approaches used to predict pit wall-rock runoff and leachate. • Review of approaches used to generate a pit lake water balance. • Review of approaches used to generate a hydrodynamic prediction. • Review of approaches used to generate a geochemical prediction of a future pit lake. - Abstract: Pit lakes are permanent hydrologic/landscape features that can result from open pit mining for metals, coal, uranium, diamonds, oil sands, and aggregates. Risks associated with pit lakes include local and regional impacts to water quality and related impacts to aquatic and terrestrial ecosystems. Stakeholders rely on predictive models of water chemistry to prepare for and manage these risks. This paper is the first of a two part series on the modeling and management of pit lakes. Herein, we review approaches that have been used to quantify wall-rock runoff geochemistry, wall-rock leachate geochemistry, pit lake water balance, pit lake limnology (i.e. extent of vertical mixing), and pit lake water quality, and conclude with guidance on the application of models within the mine life cycle. The purpose of this paper is to better prepare stakeholders, including future modelers, mine managers, consultants, permitting agencies, land management agencies, regulators, research scientists, academics, and other interested parties, for the challenges of predicting and managing future pit lakes in un-mined areas

Engineered covers for mud pit closures Central Nevada Test Area, Nevada

International Nuclear Information System (INIS)

Madsen, D.D.

2000-01-01

Two abandoned drilling mud pits impacted with petroleum hydrocarbons were determined to require closure action at the Central Nevada Test Area. The UC-4 Mud Pit C is approximately 0.12 hectares (0.3 acres) and 1.2 meters (4 feet) in depth. The UC-1 Central Mud Pit (CMP) is approximately 1.54 hectares (3.8 acres) and 2.4 meters (8 feet) in depth. Both mud pits contain bentonite drilling muds with a thin dry crust, low shear strength, low permeability, and high moisture content. The following closure methodologies were evaluated: stabilization by mixing/injection with soil, fly ash, and lime; excavation and disposal; on-site drying; thermal destruction; wick drains; administrative closure (postings and land-use restrictions); and engineered covers. Based upon regulatory closure criteria, implementation, and cost considerations, the selected remedial alternative was the construction of an engineered cover. A multilayered cover with a geo-grid and geo-synthetic clay liner (GCL) was designed and constructed over the UC-4 Mud Pit C to evaluate the constructability and applicability of the design for the CMP cover. The geo-grid provided structural strength for equipment and material loads during cover construction, and the GCL was used as a moisture infiltration barrier. The design was determined to be constructable and applicable. To reduce project costs for the CMP cover, a vegetative cover was designed with drainage toward the center of the cover rather than the perimeter. The vegetative cover with the internal drainage design resulted in a fill volume reduction of approximately 63 percent compared to the multilayered cover design with a GCL

Copper corrosion and its relationship to solar collectors:a compendium.

Energy Technology Data Exchange (ETDEWEB)

Menicucci, David F.; Mahoney, Alan Roderick

2007-07-01

Copper has many fine qualities that make it a useful material. It is highly conductive of both heat and electricity, is ductile and workable, and reasonably resistant to corrosion. Because of these advantages, the solar water heating industry has been using it since the mid-1970s as the material of choice for collectors, the fundamental component of a solar water heating system. In most cases copper has performed flawlessly, but in some situations it has been known to fail. Pitting corrosion is the usual failure mode, but erosion can also occur. In 2000 Sandia National Laboratories and the Copper Development Association were asked to analyze the appearance of pin-hole leaks in solar collector units installed in a housing development in Arizona, and in 2002 Sandia analyzed a pitting corrosion event that destroyed a collector system at Camp Pendleton. This report includes copies of the reports and accounts of these corrosion failures, and provides a bibliography with references to many papers and articles that might be of benefit to the solar community. It consolidates in a single source information that has been accumulated at Sandia relative to copper corrosion, especially as it relates to solar water heaters.

Copper tolerance mediated by polyphosphate degradation and low-affinity inorganic phosphate transport system in Escherichia coli.

Science.gov (United States)

Grillo-Puertas, Mariana; Schurig-Briccio, Lici Ariane; Rodríguez-Montelongo, Luisa; Rintoul, María Regina; Rapisarda, Viviana Andrea

2014-03-19

Metal tolerance in bacteria has been related to polyP in a model in which heavy metals stimulate the polymer hydrolysis, forming metal-phosphate complexes that are exported. As previously described in our laboratory, Escherichia coli cells grown in media containing a phosphate concentration >37 mM maintained an unusually high polyphosphate (polyP) level in stationary phase. The aim of the present work was to evaluate the influence of polyP levels as the involvement of low-affinity inorganic phosphate transport (Pit) system in E. coli copper tolerance. PolyP levels were modulated by the media phosphate concentration and/or using mutants in polyP metabolism. Stationary phase wild-type cells grown in high phosphate medium were significantly more tolerant to copper than those grown in sufficient phosphate medium. Copper addition to tolerant cells induced polyP degradation by PPX (an exopolyphosphatase), phosphate efflux and membrane polarization. ppk-ppx- (unable to synthesize/degrade polyP), ppx- (unable to degrade polyP) and Pit system mutants were highly sensitive to metal even in high phosphate media. In exponential phase, CopA and polyP-Pit system would act simultaneously to detoxify the metal or one could be sufficient to safeguard the absence of the other. Our results support a mechanism for copper detoxification in exponential and stationary phases of E. coli, involving Pit system and degradation of polyP. Data reflect the importance of the environmental phosphate concentration in the regulation of the microbial physiological state.

Metagenomic investigation of the microbial diversity in a chrysotile asbestos mine pit pond, Lowell, Vermont, USA

Directory of Open Access Journals (Sweden)

Heather E. Driscoll

2016-12-01

Full Text Available Here we report on a metagenomics investigation of the microbial diversity in a serpentine-hosted aquatic habitat created by chrysotile asbestos mining activity at the Vermont Asbestos Group (VAG Mine in northern Vermont, USA. The now-abandoned VAG Mine on Belvidere Mountain in the towns of Eden and Lowell includes three open-pit quarries, a flooded pit, mill buildings, roads, and >26 million metric tons of eroding mine waste that contribute alkaline mine drainage to the surrounding watershed. Metagenomes and water chemistry originated from aquatic samples taken at three depths (0.5 m, 3.5 m, and 25 m along the water column at three distinct, offshore sites within the mine's flooded pit (near 44°46′00.7673″, −72°31′36.2699″; UTM NAD 83 Zone 18 T 0695720 E, 4960030 N. Whole metagenome shotgun Illumina paired-end sequences were quality trimmed and analyzed based on a translated nucleotide search of NCBI-NR protein database and lowest common ancestor taxonomic assignments. Our results show strata within the pit pond water column can be distinguished by taxonomic composition and distribution, pH, temperature, conductivity, light intensity, and concentrations of dissolved oxygen. At the phylum level, metagenomes from 0.5 m and 3.5 m contained a similar distribution of taxa and were dominated by Actinobacteria (46% and 53% of reads, respectively, Proteobacteria (45% and 38%, respectively, and Bacteroidetes (7% in both. The metagenomes from 25 m showed a greater diversity of phyla and a different distribution of reads than the two upper strata: Proteobacteria (60%, Actinobacteria (18%, Planctomycetes, (10%, Bacteroidetes (5% and Cyanobacteria (2.5%, Armatimonadetes (<1%, Verrucomicrobia (<1%, Firmicutes (<1%, and Nitrospirae (<1%. Raw metagenome sequence data from each sample reside in NCBI's Short Read Archive (SRA ID: SRP056095 and are accessible through NCBI BioProject PRJNA277916.

Uranium in mining water of kaolin open pit in Zarów (Lower Silesia); methodology of determination and genetic remarks.

Science.gov (United States)

Chau, N D; Wyszomirski, P; Chruściel, E; Ochoński, A

1999-11-01

In this paper, a method of determination of uranium 238 and 234 in mining waters of Andrzej kaolin open pit in Zarów (Lower Silesia) is presented. The method is based on independent measurements of alpha and beta radiation intensities by means of a liquid scintillation spectrometer alpha/beta. The initial volume of water sample was 3 dm3, then it was diminished by chemical preparation to 6 cm3, and then 12 cm3 of scintillator was added. The lower limit of detection (for the measurement time of 8 h) for both 234U and 238U amounted to 0.02 Bq/dm3. For determination of the uranium content in ferruginous sediments precipitating from mining waters of the above-mentioned open pit, gamma ray spectrometry was used. The obtained results may be viewed as a contribution to studies on anomalous uranium concentration within this kaolin deposit. The elevated uranium content, in comparison with its average concentration in the Earth crust, is characteristic for parent rocks of Andrzej kaolin deposit, which are granitoids of Strzegom-Sobótka massif. In connection with it, the high uranium content can be observed not only in kaolin and weakly kaolinised granitoids from the deposit in question, but also in mining waters genetically related with them.

Optic Nerve Pit

Science.gov (United States)

... Conditions Frequently Asked Questions Español Condiciones Chinese Conditions Optic Nerve Pit What is optic nerve pit? An optic nerve pit is a ... may be seen in both eyes. How is optic pit diagnosed? If the pit is not affecting ...

Investigation of aerial dispersion of radioactive dust from an open-pit uranium mine by passive vinyl collectors

International Nuclear Information System (INIS)

Pettersson, H.B.; Koperski, J.

1991-01-01

Detailed investigations of the aerial dispersion of radioactive dust from the biggest open-pit U mining and milling operation in Australia were carried out. Spatial distributions of the long-lived radionuclides of 238 U series and their origin, i.e., mining and milling operations vs. natural background radiation, have been studied. Horizontal flux, dry deposition, and ground resuspension of the radionuclides were investigated along a 50-km transect in the direction of the prevailing monsoonal winds in the region. The study was performed by means of unconventional 'sticky vinyl' passive dust collectors, occasionally supported by high-volume air filter samplers. The data from the flux measurements show an inverse square to inverse cubic dependence, and the dry deposition exhibits an inverse square dependence, of radionuclide load vs. distance. The pit has been the predominant contributor of long-lived U series radionuclides to the environment within the radius of several kilometers from the operations. An aerial dispersion computer code (LUCIFER), based on a Gaussian plume model, was developed for the project. Experimental data were used as the code input data. Good agreement between the measured data and the normalized computed results was obtained

Development of a container failure function for copper

International Nuclear Information System (INIS)

King, F.; Litke, C.D.

1990-01-01

A simple approach to the modeling of failure rates for a copper container under Canadian waste disposal conditions is presented. Both uniform corrosion and pitting must be considered. Short-term failures due to fabrication defects must be taken into account. The model allows for short-term sorption of copper by the clay buffer material, and assumes a steady-state condition for uniform corrosion. Using worst-case assumptions, a container penetration time of 3300 years can be predicted

Effect of stage development of mining operations on maximization the net present value in long-term planning of open pits

OpenAIRE

Kržanović, Daniel; Rajković, Radmilo; Mikić, Miomir; Ljubojev, Milenko

2014-01-01

Long-term planning in the mining industry has one main goal: maximizing the value that is realized by excavation and processing of mineral resources. When designing the open pits, determining the stages of development the mining operations, (eng. Pushback) is one of the important factors in the process of long-term production planning. Using the different scientific methods and mathematical algorithms underlying the operation of modern software for strategic planning of production, it is poss...

What Were the Reasons for the Rapid Landslide Occurrence in “Piaseczno” Open Pit? – Analysis of the Landslide Process

Directory of Open Access Journals (Sweden)

Jakóbczyk Joanna

2015-03-01

Full Text Available Landslides are major natural hazards occurring in opencast mining. The problem of slope stability failure in the existing open pit mines as well as in those which are at a stage of technical closure is current issue in Poland and all over the world. This problem requires conducting in-depth and meaningful analysis which will identify the causes of processes characterized by a very rapid course and large extent.

Planning criteria for open pit mines under special consideration of slope stability and controlled blasting

Energy Technology Data Exchange (ETDEWEB)

Weise, H

1986-04-01

The criteria which influence the economics of a future surface mining operation are discussed; these include the size of the mine and the depth of the deposit. The methods of working are outlined - single bench, multiple bench - and choices of haulage equipment (trucks vs. conveyors) are discussed. For a mine using conveyors, the slope of the open pit will affect the operating cost. Pumps will be required to dewater the strata; it will be necessary to take steps to ensure slope stability. Bucket wheel excavators will be impeded by the presence of consolidated material, which may be best removed by shatter blasting. An example is given of the use of shatter blasting at the Neyveli lignite mine in Tamil Nadu, India. 5 references.

Study of the Rock Mass Failure Process and Mechanisms During the Transformation from Open-Pit to Underground Mining Based on Microseismic Monitoring

Science.gov (United States)

Zhao, Yong; Yang, Tianhong; Bohnhoff, Marco; Zhang, Penghai; Yu, Qinglei; Zhou, Jingren; Liu, Feiyue

2018-05-01

To quantitatively understand the failure process and failure mechanism of a rock mass during the transformation from open-pit mining to underground mining, the Shirengou Iron Mine was selected as an engineering project case study. The study area was determined using the rock mass basic quality classification method and the kinematic analysis method. Based on the analysis of the variations in apparent stress and apparent volume over time, the rock mass failure process was analyzed. According to the recent research on the temporal and spatial change of microseismic events in location, energy, apparent stress, and displacement, the migration characteristics of rock mass damage were studied. A hybrid moment tensor inversion method was used to determine the rock mass fracture source mechanisms, the fracture orientations, and fracture scales. The fracture area can be divided into three zones: Zone A, Zone B, and Zone C. A statistical analysis of the orientation information of the fracture planes orientations was carried out, and four dominant fracture planes were obtained. Finally, the slip tendency analysis method was employed, and the unstable fracture planes were obtained. The results show: (1) The microseismic monitoring and hybrid moment tensor analysis can effectively analyze the failure process and failure mechanism of rock mass, (2) during the transformation from open-pit to underground mining, the failure type of rock mass is mainly shear failure and the tensile failure is mostly concentrated in the roof of goafs, and (3) the rock mass of the pit bottom and the upper of goaf No. 18 have the possibility of further damage.

Efficiency of Low-Profile External Dumping at Open Pit Coal Mining in Kemerovo Region

Science.gov (United States)

Selyukov, Alexey; Ermolaev, Vyacheslav; Kostinez, Irina

2017-11-01

Kemerovo region is one of the largest industrial regions of Russia, with a raw material specialization. The rapid growth of the coal industry in recent years has been greatly facilitated by the expansion and development of open pit mining for coal seams extraction, accompanied by an increase in the volumes of overburden and the height of the dumps. There are about 400 objects in the Russian Federation Government Register of Waste Disposal Facilities 80% of which are dumps. Approaches both to external dumping and to the technical stage of reclamation currently contribute to the growth of geomorphic system's instability. Thus, it is proposed to slightly change the approaches to external dumping: the essence consists in the formation of an external dump of overburden, which in future would represent a favorable landscape unit of a flat surface relief used for subsequent differently directed purposes.

The Production Measurement Model of Open Pit Mine Based on Truck Operation Diagram

Directory of Open Access Journals (Sweden)

Sun Xiao-Yu

2016-01-01

Full Text Available Conventional production measurement of truck dispatching system in open pit mine has not been effectively expressed by a mathematical model, which brings a negative effect on the subsequent data mining and a compatibility issue to apply the production measurement with fixed assignment of truck. In this study, based on the proposed concept that truck is not only the carrier of transport material, but also act as the bridges and linkages between the loading sites and the unloading sites, a new truck operation diagram was established, which was further developed to a basic data matrix and a production measurement model. The new model allowed to calculatethe production measurement of the transport, loading, unloading, material and etc, respectively, as well as with any calculation in combination of more than one factor as needed.It solved the compatibility issue between conventional production measurement and the production measurement of fixed assignment of truck with good practical results.

Optimal synthesis of energy supply systems for remote open pit mines

International Nuclear Information System (INIS)

Carvalho, M.; Romero, A.; Shields, G.; Millar, D.L.

2014-01-01

electricity and syngas storage and diesel and biomass bunkering. Within the paper the energy demands for a remote, open pit mining operation located in Northern Ontario are considered as a case study to illustrate the technique and investigations. As expected, for mines close to electricity, natural gas, and diesel distribution infrastructures, the optimal choice is to connect. When a constraint is applied specifying that connection is not possible, as would be for the case exemplified, the optimal choice includes some of the more exotic options for mine site energy supply. - Highlights: •Optimal mine site energy supply methodology is established. •Methodology permits innovative, lower cost, energy supply solutions to be identified. •The methodology allows for electricity and syngas storage and diesel and biomass bunkering. •A remote, open pit mining operation located in Northern Ontario is considered as a case study. •The optimal solution includes some of the more exotic options for mine site energy supply

Investigating pitting in X65 carbon steel using potentiostatic polarisation

Science.gov (United States)

Mohammed, Sikiru; Hua, Yong; Barker, R.; Neville, A.

2017-11-01

Although pitting corrosion in passive materials is generally well understood, the growth of surface pits in actively-corroding materials has received much less attention to date and remains poorly understood. One of the key challenges which exists is repeatedly and reliably generating surface pits in a practical time-frame in the absence of deformation and/or residual stress so that studies on pit propagation and healing can be performed. Another pertinent issue is how to evaluate pitting while addressing general corrosion in low carbon steel. In this work, potentiostatic polarisation was employed to induce corrosion pits (free from deformation or residual stress) on actively corroding X65 carbon steel. The influence of applied potential (50 mV, 100 mV and 150 mV vs open circuit potential) was investigated over 24 h in a CO2-saturated, 3.5 wt.% NaCl solution at 30 °C and pH 3.8. Scanning electron microscopy (SEM) was utilised to examine pits, while surface profilometry was conducted to measure pit depth as a function of applied potential over the range considered. Analyses of light pitting (up to 120 μm) revealed that pit depth increased linearly with increase in applied potential. This paper relates total pit volume (measured using white light interferometry) to dissipated charge or total mass loss (using the current response for potentiostatic polarisation in conjunction with Faraday's law). By controlling the potential of the surface (anodic) the extent of pitting and general corrosion could be controlled. This allowed pits to be evaluated for their ability to continue to propagate after the potentiostatic technique was employed. Linear growth from a depth of 70 μm at pH 3.8, 80 °C was demonstrated. The technique offers promise for the study of inhibition of pitting.

Uranium mills and mines environmental restoration in Spain

International Nuclear Information System (INIS)

Perez Estevez, C.; Lozano Martinez, F.

2000-01-01

ENRESA and ENUSA have dismantled and restored a uranium mill in Andujar (Andalucia), a uranium facility based on open pit mining and plant in La Haba (Extremadura) and 19 old uranium mines in Andalucia and Extremadura. The Andujar Uranium Mill was operated from 1959 to 1981 and has been restorated between 1991 and 1994. The site included the tailings pile and the processing plant. The Haba Uranium Site included the Plant (operating from 1976 to 1999), four open-pit mines (operating from 1966 to 1990), the heaps leaching and the tailings dam and has been restorated between 1992 and 1997. The 19 abandoned uranium mines were developed by underground mining with the exception of two sites, which were operated by open pit mining. Mining operations started around 1959 and were shutdown in 1981. There was a great diversity among the mines, in terms of site conditions. Whereas in some sites there was little trace of the mining works, in other sites large excavations, mining debris piles, abandoned shafs and galeries and remaining surface structures and equipment were encountered. (author)

A New Algorithm for Determining Ultimate Pit Limits Based on Network Optimization

OpenAIRE

Ali Asghar Khodayari

2013-01-01

One of the main concerns of the mining industry is to determine ultimate pit limits. Final pit is a collection of blocks, which can be removed with maximum profit while following restrictions on the slope of the mine’s walls. The size, location and final shape of an open-pit are very important in designing the location of waste dumps, stockpiles, processing plants, access roads and other surface facilities as well as in developing a production program. There are numerous methods for designing...

Efficiency of Low-Profile External Dumping at Open Pit Coal Mining in Kemerovo Region

Directory of Open Access Journals (Sweden)

Selyukov Alexey

2017-01-01

Full Text Available Kemerovo region is one of the largest industrial regions of Russia, with a raw material specialization. The rapid growth of the coal industry in recent years has been greatly facilitated by the expansion and development of open pit mining for coal seams extraction, accompanied by an increase in the volumes of overburden and the height of the dumps. There are about 400 objects in the Russian Federation Government Register of Waste Disposal Facilities 80% of which are dumps. Approaches both to external dumping and to the technical stage of reclamation currently contribute to the growth of geomorphic system's instability. Thus, it is proposed to slightly change the approaches to external dumping: the essence consists in the formation of an external dump of overburden, which in future would represent a favorable landscape unit of a flat surface relief used for subsequent differently directed purposes.

Treatment of sulphated water of surface origin produced by an open pit coal mine

Directory of Open Access Journals (Sweden)

Alan Campos-Sánchez

2016-12-01

Full Text Available The purpose of this study was to select the most suitable method of treatment of sulfated water produced by an open pit coal mine in Venezuela. Samples of water taken on surface, middle and bottom of water bodies in three areas were subjected to basic, gravimetric, volumetric and colorimetric analysis. The results indicated that the pH is within limits permitted by current environmental regulations, while total suspended solids, total dissolved solids, and sulfates exceed the normed values. The aerobic wetland method was selected as the most efficient for the removal of sulfates, depending on the physicochemical characteristics of the sulphated waters from the mine and because they are systems that use natural energy to purify water, its construction and maintenance costs Is significantly inferior to the conventional treatments and because, being replicas of natural ecosystems, they are integrated to the environment.

Pitting corrosion of Inconel 600 in chloride and sulfate solutions at low temperature

International Nuclear Information System (INIS)

Chang Mingyu; Yu Geping

1993-01-01

Pitting corrosion of Inconel 600 was examined in chloride and sulfate solutions through usage of potentiodynamic polarization techniques. The effects of chloride and sulfate concentration were investigated in the range of 0.0001 to 0.1 M. Increasing chloride concentrations resulted in active shifts of the pit nucleation potential. Immunity to pitting corrosion was evident at a chloride level below 0.005 M. Increasing sulfate concentrations resulted in improved pitting resistance of Inconel 600 in chloride solutions. Detrimental effects associated with pitting were evident with low-level sulfate being added to dilute chloride media. The density of pits increased with increasing chloride concentrations or temperature between room temperature and 70 C. Systematic trends for the depth of pits were not evident. The observations of pitting corrosion in open immersion were consistent with those in polarization methods. Corrosion products contained in the pits were enriched in nickel, chromium and iron with a small amount of titanium and silicon. The enrichment of chlorine or sulfur was still, however, not found. (orig.)

Long-Term Planning for Open Pits for Mining Sulphide-Oxide Ores in Order to Achieve Maximum Profit

Science.gov (United States)

Kržanović, Daniel; Conić, Vesna; Stevanović, Dejan; Kolonja, Božo; Vaduvesković, Jovan

2017-12-01

Profitable exploitation of mineralised material from the earth's crust is a complex and difficult task that depends on a comprehensive planning process. Answering the question of how to plan production depends on the geometry of the deposit, as well as the concentration, distribution, and type of minerals in it. The complex nature of mineral deposits largely determines the method of exploitation and profitability of mining operations. In addition to unit operating costs and metal prices, the optimal recovery of and achievement of maximum profit from deposits of sulphide-oxide ores also depend, to a significant extent, on the level of technological recovery achieved in the ore processing procedure. Therefore, in defining a long-term development strategy for open pits, special attention must be paid to the selection of an optimal procedure for ore processing in order to achieve the main objective: maximising the Net Present Value (NPV). The effect of using two different processes, flotation processing and hydrometallurgical methods (bioleaching acid leaching), on determining the ultimate pit is shown in the case of the Kraku Bugaresku-Cementacija sulphide-oxide ore deposit in eastern Serbia. Analysis shows that the application of hydrometallurgical methods of processing sulphide-oxide ore achieved an increase in NPV of 20.42%.

Conditions of Antonin seam exploitation in the open pit Druzba near Sokolov with regard to the protection of thermal and mineral water resources in Karlovy Vary

International Nuclear Information System (INIS)

Grmela, A.; Sterba, J.

1997-01-01

From new structural-tectonic findings concerning the extent and character of the Nove Sedlo fault in the area of the Druzba open pit in the Sokolov Basin, it is evident that it is a form of listric fault of shallow range, ending in an intermediate slip. This finding has a decisive relevance for deciding as to the current placement of the pit in the protection zone of Karlovy Vary's thermal springs. For the purposes of the exploitation of the Antonin seam, it is necessary to create a network of multipurpose bore holes at the bottom of the pit and in front of the working face for the regulation of pressure in the basal aquifer and to ensure unity of monitoring and its complex evaluation on the basis of numerical modelling of the hydrodynamic state of the basal aquifer and the geotechnical processes of the seam's impermeable bedrock. 4 refs

Cavitation Resistance in Seedless Vascular Plants: The Structure and Function of Interconduit Pit Membranes1[W][OPEN

Science.gov (United States)

Brodersen, Craig; Jansen, Steven; Choat, Brendan; Rico, Christopher; Pittermann, Jarmila

2014-01-01

Plant water transport occurs through interconnected xylem conduits that are separated by partially digested regions in the cell wall known as pit membranes. These structures have a dual function. Their porous construction facilitates water movement between conduits while limiting the spread of air that may enter the conduits and render them dysfunctional during a drought. Pit membranes have been well studied in woody plants, but very little is known about their function in more ancient lineages such as seedless vascular plants. Here, we examine the relationships between conduit air seeding, pit hydraulic resistance, and pit anatomy in 10 species of ferns (pteridophytes) and two lycophytes. Air seeding pressures ranged from 0.8 ± 0.15 MPa (mean ± sd) in the hydric fern Athyrium filix-femina to 4.9 ± 0.94 MPa in Psilotum nudum, an epiphytic species. Notably, a positive correlation was found between conduit pit area and vulnerability to air seeding, suggesting that the rare-pit hypothesis explains air seeding in early-diverging lineages much as it does in many angiosperms. Pit area resistance was variable but averaged 54.6 MPa s m−1 across all surveyed pteridophytes. End walls contributed 52% to the overall transport resistance, similar to the 56% in angiosperm vessels and 64% in conifer tracheids. Taken together, our data imply that, irrespective of phylogenetic placement, selection acted on transport efficiency in seedless vascular plants and woody plants in equal measure by compensating for shorter conduits in tracheid-bearing plants with more permeable pit membranes. PMID:24777347

Copper and brass aged at open circuit potential in slightly alkaline solutions

International Nuclear Information System (INIS)

Procaccini, R.; Vazquez, M.; Cere, S.

2009-01-01

Surface oxide films were grown on 99.99% copper and brass (copper-zinc alloy, Cu77Zn21Al2) in 0.1 mol L -1 borax solution at open circuit potential and were characterized using various experimental techniques. The composition of the passive films formed in situ on the different materials was studied using differential reflectance spectroscopy. The thickness of the oxide layers on copper and brass was compared by chronopotentiometric curves and potentiodynamic reductions. The electrical properties of each oxide were analyzed by means of electrochemical impedance spectroscopy. Their influence on the oxygen reduction reaction was also investigated using voltammetry hydrodynamic tools such as the rotating disk electrode. The results show that the incorporation of Zn to Cu in brass changes the composition and the thickness of the surface film. The films grown on brass tend to be thicker but less resistive and Zn compounds incorporate to the film. This is supported by results from reflectance and impedance spectroscopy. The kinetics of oxygen reduction is strongly inhibited on oxidized electrodes, particularly in the case of brass. The global number of exchanged electrons remains close to four and seems to be independent of the presence of surface oxides.

Geochemical fractionation of metals and metalloids in tailings and appraisal of environmental pollution in the abandoned Musina Copper Mine, South Africa.

Science.gov (United States)

Gitari, M W; Akinyemi, S A; Ramugondo, L; Matidza, M; Mhlongo, S E

2018-04-30

The economic benefits of mining industry have often overshadowed the serious challenges posed to the environments through huge volume of tailings generated and disposed in tailings dumps. Some of these challenges include the surface and groundwater contamination, dust, and inability to utilize the land for developmental purposes. The abandoned copper mine tailings in Musina (Limpopo province, South Africa) was investigated for particle size distribution, mineralogy, physicochemical properties using arrays of granulometric, X-ray diffraction, and X-ray fluorescence analyses. A modified Community Bureau of Reference (BCR) sequential chemical extraction method followed by inductively coupled plasma mass spectrometry/atomic emission spectrometry (ICP-MS/AES) technique was employed to assess bioavailability of metals. Principal component analysis was performed on the sequential extraction data to reveal different loadings and mobilities of metals in samples collected at various depths. The pH ranged between 7.5 and 8.5 (average ≈ 8.0) indicating alkaline medium. Samples composed mostly of poorly grated sands (i.e. 50% fine sand) with an average permeability of about 387.6 m/s. Samples have SiO 2 /Al 2 O 3 and Na 2 O/(Al 2 O 3  + SiO 2 ) ratios and low plastic index (i.e. PI ≈ 2.79) suggesting non-plastic and very low dry strength. Major minerals were comprised of quartz, epidote, and chlorite while the order of relative abundance of minerals in minor quantities is plagioclase > muscovite > hornblende > calcite > haematite. The largest percentage of elements such as As, Cd and Cr was strongly bound to less extractable fractions. Results showed high concentration and easily extractable Cu in the Musina Copper Mine tailings, which indicates bioavailability and poses environmental risk and potential health risk of human exposure. Principal component analysis revealed Fe-oxide/hydroxides, carbonate and clay components, and copper ore process

A SIMPLE APPROACH TO ASSESSING COPPER PITTING CORROSION TENDENCIES AND DEVELOPING CONTROL STRATEGIES

Science.gov (United States)

Localized corrosion of copper premise plumbing in drinking water distribution systems can lead to pinhole leaks, which are a growing problem for many homeowners. Despite the fact that water quality is an important factor associated with localized copper corrosion, definitive appr...

Chemical Data for Rock, Sediment, Biological, Precipitate, and Water Samples from Abandoned Copper Mines in Prince William Sound, Alaska

Science.gov (United States)

Koski, Randolph A.; Munk, LeeAnn

2007-01-01

In the early 20th century, approximately 6 million metric tons of copper ore were mined from numerous deposits located along the shorelines of fjords and islands in Prince William Sound, Alaska. At the Beatson, Ellamar, and Threeman mine sites (fig. 1), rocks containing Fe, Cu, Zn, and Pb sulfide minerals are exposed to chemical weathering in abandoned mine workings and remnant waste piles that extend into the littoral zone. Field investigations in 2003 and 2005 as well as analytical data for rock, sediment, precipitate, water, and biological samples reveal that the oxidation of sulfides at these sites is resulting in the generation of acid mine drainage and the transport of metals into the marine environment (Koski and others, 2008; Stillings and others, 2008). At the Ellamar and Threeman sites, plumes of acidic and metal-enriched water are flowing through beach gravels into the shallow offshore environment. Interstitial water samples collected from beach sediment at Ellamar have low pH levels (to ~3) and high concentrations of metals including iron, copper, zinc, cobalt, lead, and mercury. The abundant precipitation of the iron sulfate mineral jarosite in the Ellamar gravels also signifies a low-pH environment. At the Beatson mine site (the largest copper mine in the region) seeps containing iron-rich microbial precipitates drain into the intertidal zone below mine dumps (Foster and others, 2008). A stream flowing down to the shoreline from underground mine workings at Beatson has near-neutral pH, but elevated levels of zinc, copper, and lead (Stillings and others, 2008). Offshore sediment samples at Beatson are enriched in these metals. Preliminary chemical data for tissue from marine mussels collected near the Ellamar, Threeman, and Beatson sites reveal elevated levels of copper, zinc, and lead compared to tissue in mussels from other locations in Prince William Sound (Koski and others, 2008). Three papers presenting results of this ongoing investigation of

Transitional phase for small steeply dipping ore bodies from open pit to underground mining:a case study from Scandinavian mining industry

OpenAIRE

Hassan, Syed Alley; Greberg, Jenny; Schunnesson, Håkan

2012-01-01

The transition from open pit to underground mining involves drastically changes in the production system. The equipment for underground mining will change as well as the logistics and the transportation system. Demands of rock stability and control will also change in nature and in equipment needed. At the same time the large investments in underground infrastructure and equipment require short lead times to maintain a high cash flow for the companies. Without proper planning many problems ca...

Blasting methods for heterogeneous rocks in hillside open-pit mines with high and steep slopes

Science.gov (United States)

Chen, Y. J.; Chang, Z. G.; Chao, X. H.; Zhao, J. F.

2017-06-01

In the arid desert areas in Xinjiang, most limestone quarries are hillside open-pit mines (OPMs) where the limestone is hard, heterogeneous, and fractured, and can be easily broken into large blocks by blasting. This study tried to find effective technical methods for blasting heterogeneous rocks in such quarries based on an investigation into existing problems encountered in actual mining at Hongshun Limestone Quarry in Xinjiang. This study provided blasting schemes for hillside OPMs with different heights and slopes. These schemes involve the use of vertical deep holes, oblique shallow holes, and downslope hole-by-hole sublevel or simultaneous detonation techniques. In each bench, the detonations of holes in a detonation unit occur at intervals of 25-50 milliseconds. The research findings can offer technical guidance on how to blast heterogeneous rocks in hillside limestone quarries.

Water quality in gravel pits in the Bratislava area

International Nuclear Information System (INIS)

Flakova, R.; Rohacikova, A.; Zenisova, Z.

1999-01-01

The gravel pits around Bratislava have an esthetic, urban and recreational function. Open water table areas are in a direct contact with the air and acquire some characteristics of the surface water. The quality of open water table is much more susceptible to pollution than that of groundwater. Wet and dry deposition, water inflow from the surrounding surface, unmanageable sewerage effluents, solid and liquid wastes, but also the water birds contribute to the pollution. The Department of Hydrogeology has monitored the water quality in six gravel pits (Cunovo, Drazdiak, Strkovec, Pasienky, Zlate Piesky, Vajnory) since 1976 with an an interruption between 1988 - 1993. Two sampling per year have been made since 1994 and after 1998 the analyses have been supplemented by Na, K, Fe, Mn, by oxygen regime parameters, by trace elements (As, Ag, Cd, Co, Cu, Cr, Hg, Ni, Pb, V, Zn) and by organic pollutants. As regards the oxygen regime, the water quality pits is very good. The anthropogenic influence is expressed mainly by the increased contents of sulfates and chlorides. Most problematic trace elements are the mercury and vanadium (Drazdiak, Zlate Piesky and Vajnory). (authors)

A copper container corrosion model for the in-room emplacement of used CANDU fuel

International Nuclear Information System (INIS)

King, F.

1996-11-01

Copper containers in a Canadian nuclear fuel waste disposal vault are expected to undergo uniform corrosion and, possibly, pitting. The corrosion behaviour of the containers will be dictated by the evolution of environmental conditions within the disposal vault. The environment will evolve from an early warm, oxidizing phase, during which fast uniform corrosion and pitting may occur, to an indefinite period of cool, anoxic conditions, during which the container will only be susceptible to slow uniform corrosion. The results of corrosion and electrochemical studies of the uniform corrosion of Cu in O 2 -containing Cl - solutions are discussed and a detailed reaction mechanism presented. The relevant literature on pitting corrosion is briefly reviewed and models for the prediction of pit depth discussed. The potential for microbially influenced corrosion and stress-corrosion cracking is discussed, as are vapour-phase corrosion and the effects of β-radiation. The use of natural analogues for justifying long-term corrosion predictions is also considered. Finally, a model for uniform corrosion and pitting is presented and container lifetimes predicted. Copper containers having a minimum wall thickness of 25.4 mm are not predicted to fail by corrosion in periods 6 a. Thus, despite the assumption of poor rock quality made here, the safety of the entire disposal concept can be assured by the use of a long-lived container. (author). 125 refs., 1 tab., 24 figs

Typical whole body vibration exposure magnitudes encountered in the open pit mining industry.

Science.gov (United States)

Howard, Bryan; Sesek, Richard; Bloswick, Don

2009-01-01

According to recent research, a causal link has been established between occupational exposure to whole body vibration and an increased occurrence of low back pain. To aid in the further development of an in-house health and safety program for a large open pit mining facility interested in reducing back pain among its operators, whole body vibration magnitudes were characterized for a range of jobs. Specifically, thirty-five individual jobs from five different areas across the facility were evaluated for tri-axial acceleration levels during normal operating conditions. Tri-axial acceleration magnitudes were categorized into thirteen job groups. Job groups were ranked according to exposure and compared to the ISO 2631-1 standard for health risk assessment. Three of the thirteen job groups produced tri-axial acceleration magnitudes below the ISO 2631-1 low/moderate health caution limit for a twelve hour exposure. Six of the thirteen job groups produced exposures within the moderate health risk range. Four job groups were found to subject operators to WBV acceleration magnitudes above the moderate/high health caution limit.

Initiation, Propagation, and Mitigation of Aluminum and Chlorine Induced Pitting Corrosion

OpenAIRE

Marshall, Becki Jean

2004-01-01

Previous research by Rushing et al. (2002) identified key factors contributing to the formation of pinhole leaks in copper plumbing. These factors included high chlorine, pH levels and the presence of aluminum solids. Experiments were conducted to 1) examine the interplay between these constituents, 2) confirm that the water was aggressive enough to eat a hole through a pipe, 3) examine phosphate inhibition, and 4) try to determine the scope of this pitting problem in other distribution sy...

Theoretical study of the dissolution kinetics of galena and cerussite in an abandoned mining area (Zaida mine, Morocco)

Science.gov (United States)

El Alaoui, Lamiae; Dekayir, Abdelilah

2018-05-01

In the abandoned mine in Zaida, the pit lakes filled with water constitute significant water reserves. In these lakes, the waters are permanently in contact with ore deposit (cerussite and galena). The modelling of the interaction of waters with this mineralization shows that cerussite dissolves more rapidly than galena. This dissolution is controlled by the pH and dissolved oxygen concentration in solution. The lead concentrations recorded in these lakes come largely from the dissolution of cerussite.

The pitting resistance of AISI 316 stainless steel passivated in diluted nitric acid

International Nuclear Information System (INIS)

Barbosa, M.A.

1983-01-01

The pitting resistance of AISI 316 stainless steel after passivation in diluted nitric acid was studied in comparison with that of non-passivated specimens. The passivation treatment increased the pitting potential but decreased the resistance to crevice corrosion under open circuit conditions in aerated sea water. Immersion in the nitric acid solution was found to remove the sulphide inclusions from the metal surface, thus eliminating the most susceptible sites for attack. In the absence of sulphide particles pitting nucleated at aluminium-rich oxides. (author)

IMPACT OF WATER CHEMISTRY ON LOCALIZED CORROSION OF COPPER PITTING

Science.gov (United States)

This project will help identify what waters are problematic in causing the corrosion of copper pipes and improve understanding of how water distribution leads to corrosion. This project will also focus on the prevention of pinhole leaks and how to reverse them once they occur. ...

TESTING OF THE TRUTH IN ANDREI PLATONOV’S TALE THE FOUNDATION PIT

Directory of Open Access Journals (Sweden)

Marina Vladimirovna Zavarkina

2014-11-01

Full Text Available Analyzing the manuscript of Andrei Platonov’s tale The Foundation Pit and his early journalism the author traces the evolution of Platonov’s views on the problem of the search for the truth. Analysis of the dynamic transcription of the The Foundation Pit manuscript enabled to show that by the end of the 1920s Platonov had abandoned rationalistic interpretations of the concept of «truth», including in its "Bogdanov’s edition". Platonov increasingly questioned the capabilities of socialist science, based on materialism, to fi nd out the truth about the world, and changed his views on work as the only method of learning the truth. He departed from the materialistic concept of learning and shifted towards the religious and philosophical tradition: in the end the formula of P. Florensky "truth-estina (to be in existence" is getting more and more essential and it is outlined a shift of the concept of “truth” from a cognitive-materialistic category (“invent” / “to do” truth to an ontological and moral category.

Investigation of the long-term behaviour of residues of brown coal upgrading processes in an underground deposit in the geogenic conditions of potassium and rock salt mining. Text volume. Final report

International Nuclear Information System (INIS)

1994-01-01

Residues of brown coal upgrading processes are problematic substances that require extensive monitoring. In East Germany, these residues were usually stored above ground in abandoned open pits and industrial waste dumps. In the Land of Thuringia, the most urgent poblems are posed by the ''Neue Sorge'' abandoned open pit near Rositz and the Rusendorf industrial waste dump. In both cases, large volumes of highly polluted waste materials must be disposed of. The method of choice recommended for disposal is the combustion in a hazardous-waste incinerator in accordance with the specifications of the Waste Management Technical Guide (TA Abfall). Preliminary studies are currently being made for the construction of a waste incinerating plant in this region. An alternative option for disposal would be underground storage in an abandoned salt mine. Thuringia has a number of abandoned potassium mines that appear to be well suited for this purpose. On the other hand, there have been no systematic investigations so far on the long-term behaviour of hazardous waste under the geogenic conditions of potassium and rock salt mining, so that further studies will be necessary. (orig.)

Type I fitting of copper tubes from a water distribution system

CSIR Research Space (South Africa)

Fernandes, PJL

1998-03-01

Full Text Available with a greenish scale of a copper compound called malachite. Beneath this scale, the tube surface is covered with a smooth, shiny layer of dark cuprite which is very friable and easily spalled off. Pits are usually...

Anodic polarization behavior of pure copper in carbonate solutions

International Nuclear Information System (INIS)

Kawasaki, Manabu; Taniguchi, Naoki; Naitou, Morimasa

2008-03-01

Copper is one of the candidate materials for overpacks. The redox condition at the early stage of the post closure will be oxidizing. In order to understand the influence of environmental factors on the corrosion behavior of copper in such oxidizing environment, anodic polarization tests were performed in carbonate aqueous solution with varying the concentration of representative chemical species in groundwater. As the results of potentiodynamic and potentiostatic tests, anodic polarization behavior of pure copper was summarized as follows; Carbonate ion and bicarbonate ion promoted the passivation of pure copper, and suppressed the initiation of film breakdown. Chloride ion promoted both the active dissolution and initiation of film breakdown of pure copper. The influence of sulfate ion and pH was small, but the action of sulfate ion to the pure copper was similar to that of chloride ion, and the increase of pH was likely to promote the passivation and suppress the initiation of film breakdown. The film breakdown potential, Eb, was represented as a function of the ratio of aggressive ion and inhibiting ion such as [Cl - ]/[HCO 3 - ], [SO 4 2- ]/[HCO 3 - ]. When the ratio exceeds a certain value, the anodic polarization curve becomes active dissolution type so that no macroscopic film breakdown can not be occurred. The lower limit of Eb in passive type region was estimated to be about -200 mV vs. SCE. As the results of potentio static tests, the corrosion form near the Eb was uniform dissolution over the surface, but pitting corrosion and non-uniform corrosion occurred according to the condition of the test solution. Neither pitting corrosion nor non-uniform corrosion occurred at the potential below Eb in every test cases. (author)

Integration of OHS into Risk Management in an Open-Pit Mining Project in Quebec (Canada

Directory of Open Access Journals (Sweden)

Adel Badri

2011-09-01

Full Text Available Despite undeniable progress, the mining industry remains the scene of serious accidents revealing disregard for occupational health and safety (OHS and leaving open the debate regarding the safety of its employees. The San José mine last collapse near Copiapó, Chile on 5 August 2010 and the 69-day rescue operation that followed in order to save 33 miners trapped underground show the serious consequences of neglecting worker health and safety. The aim of this study was to validate a new approach to integrating OHS into risk management in the context of a new open-pit mining project in Quebec, based on analysis of incident and accident reports, semi-structured interviews, questionnaires and collaborative field observations. We propose a new concept, called hazard concentration, based on the number of hazards and their influence. This concept represents the weighted fraction of each category of hazards related to an undesirable event. The weight of each category of hazards is calculated by AHP, a multicriteria method. The proposed approach included the creation of an OHS database for facilitating expert risk management. Reinforcing effects between hazard categories were identified and all potential risks were prioritized. The results provided the company with a rational basis for choosing a suitable accident prevention strategy for its operational activities.

Analysis of rainfall characteristics and its related disasters of slag disposal pit of a certain Gold-Copper Deposit in Fujian province

Science.gov (United States)

Pan, Huali; Hu, Mingjian; Ou, Guoqiang

2017-04-01

According to the geological investigation in Fujian province, the total number of geological disasters was 9513, in which the number of landslide, collapse, unstable slope and surface collapse was 5816, 1888, 1591, 103 and 115 respectively. The main geological disaster was the landslide with 61.1% of total geological disasters. Among all these geological disasters, only 6.0% was relative stable, 17.0% was basic stable, nearly 76.0% was unstable. The slope disaster was the main geological disaster, if the unstable slope was the potential landslide or collapse; the slope collapse was 98.0% of all geological disasters. The rainfall, in particular the heavy rain, was direct dynamic factor for geological disasters, but the occurrence probability of geological disasters was different because of the sensitivity of the geological environment though of the same intensity rainfall. To obtain the characteristics of soil erosion under the rainfall condition, the rainfall characteristics and its related disasters of slag disposal pit of a certain Gold-Copper Deposit in Fujian province was analyzed by the meteorological and rainfall data. According to the distribution of monitoring stations of hydrological and rainfall in Longyan city of Fujian province and the location of gold-copper deposit, the Shanghang monitoring station of hydrological and rainfall was chosen, which is the nearest one to the gold-copper deposit. Then main parameters of the prediction model, the antecedent precipitation, the rainfall on the day and the rainfall threshold, were calculated by using the rainfall data from 2002 to 2010. And the relationship between geological disasters and the rainfall characteristics were analyzed. The results indicated that there was high risk for the debris flow with landslide collapse when either the daily rainfall was more than 100.0 mm, or the total rainfall was more than 136.0mm in the gold-copper deposit and the Shanghang region. At the same time, although there was few

Pitting of Incoloy 800 in presence of CuII

International Nuclear Information System (INIS)

Bianchi, G.L.; Alvarez, M.G.

1993-01-01

The pitting behaviour of Incoloy 800 in presence of Cu II ions, at 60 degrees C and 280 degrees C was studied by long term exposition of specimens in aqueous cupric chloride solutions. At 60 degrees C experiments were performed in aerated (7 ppm O 2 ) and deaerated solutions containing 500, 1000, 2000, 10000 and 20000 ppm CuCl 2 . At 280 degrees C experiments were performed in deaerated 20 ppm, 50 ppm and 100 ppm CuCl 2 solutions. During each experiment the open circuit potential of the alloy was measured as a function of time. After corrosion test the specimens were examined by Scanning Electron Microscopy for the presence of pits. In another set of experiments potentiodynamic anodic polarization curves were used to determine the pitting potential of Incoloy 800 in deaerated NaCl solutions at chloride concentrations and pH values corresponding to those possessed by solutions containing 20 ppm to 20000 ppm CuCl 2 . At 60 degrees C pitting was observed in those solutions where the CuCl 2 concentration is higher than 1000 ppm. At 280 degrees C pitting was found in the specimens exposed to those solutions where the CuCl 2 concentration was higher than 20 ppm. (author). 3 refs

The Influences of Artificial Aging Temperature and Time on Pitting Susceptibility of SiCp/ AA2024 MMCs

International Nuclear Information System (INIS)

Kim, S. K.; Jo, C. J.; Kwon, B. H.; Hwang, W. S.

2000-01-01

The effects of artificial aging temperature and time were investigated on the pitting behaviors of SiCp/ AA2024 composites through measuring the changes of open circuit potential, pitting potential, and repassivation potential in a 3.5 wt% NaCl solution. And, the influence of microstructure on the pitting susceptibility was studied by measurement of TEM images. AA2024 Al alloy and 15vol%SiCp/ AA2024 composites were fabricated by vacuum hot pressing and hot extrusion with an extrusion ratio of 25 : 1. They were solutionized at 495 .deg. C for 4 hours, and aged at 130, 150, 170, and 190 .deg. C for 1, 2, 4, 8, and 16 hours. In aerated 3.5% NaCl solutions, the open circuit potential and pitting potential of both AA2024 alloy and composites were similar each other, and pitting occurred immediately at immersed condition. The pitting potential was decreased with increasing aging temperature and time. Also, the repassivation potential of SiCp/ AA2024 composites was decreased as increasing aging temperature and time. It was concluded that formation and growth of S' and S phase by artificial aging promoted the pitting susceptibility of SiCp/ AA2024 composites because these phases, easily soluble by forming galvanic couples with substrate Al alloy, served as preferential sites for nucleation of pits

Hyperspectral analysis for qualitative and quantitative features related to acid mine drainage at a remediated open-pit mine

Science.gov (United States)

Davies, G.; Calvin, W. M.

2015-12-01

The exposure of pyrite to oxygen and water in mine waste environments is known to generate acidity and the accumulation of secondary iron minerals. Sulfates and secondary iron minerals associated with acid mine drainage (AMD) exhibit diverse spectral properties in the ultraviolet, visible and near-infrared regions of the electromagnetic spectrum. The use of hyperspectral imagery for identification of AMD mineralogy and contamination has been well studied. Fewer studies have examined the impacts of hydrologic variations on mapping AMD or the unique spectral signatures of mine waters. Open-pit mine lakes are an additional environmental hazard which have not been widely studied using imaging spectroscopy. A better understanding of AMD variation related to climate fluctuations and the spectral signatures of contaminated surface waters will aid future assessments of environmental contamination. This study examined the ability of multi-season airborne hyperspectral data to identify the geochemical evolution of substances and contaminant patterns at the Leviathan Mine Superfund site. The mine is located 24 miles southeast of Lake Tahoe and contains remnant tailings piles and several AMD collection ponds. The objectives were to 1) distinguish temporal changes in mineralogy at a the remediated open-pit sulfur mine, 2) identify the absorption features of mine affected waters, and 3) quantitatively link water spectra to known dissolved iron concentrations. Images from NASA's AVIRIS instrument were collected in the spring, summer, and fall seasons for two consecutive years at Leviathan (HyspIRI campaign). Images had a spatial resolution of 15 meters at nadir. Ground-based surveys using the ASD FieldSpecPro spectrometer and laboratory spectral and chemical analysis complemented the remote sensing data. Temporal changes in surface mineralogy were difficult to distinguish. However, seasonal changes in pond water quality were identified. Dissolved ferric iron and chlorophyll

Study of pitting corrosion in line-pipe steel under the influence of remanent magnetization

Energy Technology Data Exchange (ETDEWEB)

Espina-Hernandez, J H; Caleyo, F; Hallen, J M [Instituto Politecnico Nacional (IPN), Zacatenco (Mexico)

2009-07-01

The influence of remanent magnetization on pitting corrosion in line-pipe steels is studied. Pitting corrosion experiments have been carried out on samples of an API 5L grade 52 steel under a magnetization level of the same order of magnitude of the remanent magnetization in the pipeline wall after in-line inspection based on magnetic flux leakage. The samples were magnetized using rings of the same grade as the investigated steel. Immediately after magnetization, the investigated samples were subjected to pitting by immersing them in a solution containing dissolved Cl{sup -} and SO{sup 2-}{sub 4} and ions. The pitting experiments were conducted during a seven days period. The pit depth distribution and the maximum pit depth in each sample were recorded and used to conduct extreme value analyses of the pitting process in magnetized and non-magnetized control samples. The statistical assessment of the pitting corrosion data collected during this study shows that the magnetic field reduces the average depth of the pit population and also the extreme pit depth values that can be predicted from the maximum values observed in the magnetized samples in comparison with to the non-magnetized control samples. Scanning electron microscopy observations show that the magnetic field alters the pit morphology by increasing the pit mouth opening. (author)

Pitting corrosion as a mixed system: coupled deterministic-probabilistic simulation of pit growth

Science.gov (United States)

Ibrahim, Israr B. M.; Fonna, S.; Pidaparti, R.

2018-05-01

Stochastic behavior of pitting corrosion poses a unique challenge in its computational analysis. However, it also stems from electrochemical activity causing general corrosion. In this paper, a framework for corrosion pit growth simulation based on the coupling of the Cellular Automaton (CA) and Boundary Element Methods (BEM) is presented. The framework assumes that pitting corrosion is controlled by electrochemical activity inside the pit cavity. The BEM provides the prediction of electrochemical activity given the geometrical data and polarization curves, while the CA is used to simulate the evolution of pit shapes based on electrochemical activity provided by BEM. To demonstrate the methodology, a sample case of local corrosion cells formed in pitting corrosion with varied dimensions and polarization functions is considered. Results show certain shapes tend to grow in certain types of environments. Some pit shapes appear to pose a higher risk by being potentially significant stress raisers or potentially increasing the rate of corrosion under the surface. Furthermore, these pits are comparable to commonly observed pit shapes in general corrosion environments.

Is Playing in the Pit Really the Pits?: Pain, Strength, Music Performance Anxiety, and Workplace Satisfaction in Professional Musicians in Stage, Pit, and Combined Stage/Pit Orchestras.

Science.gov (United States)

Kenny, Dianna T; Driscoll, Tim; Ackermann, Bronwen J

2016-03-01

Typically, Australian orchestral musicians perform on stage, in an orchestra pit, or in a combination of both workplaces. This study explored a range of physical and mental health indicators in musicians who played in these different orchestra types to ascertain whether orchestra environment was a risk factor affecting musician wellbeing. Participants comprised 380 full-time orchestral musicians from the eight major state orchestras in Australia comprised of two dedicated pit orchestras, three stage-only symphonic orchestras, and three mixed stage/pit orchestras. Participants completed a physical assessment and a range of self-report measures assessing performance-related musculoskeletal disorders (PRMD), physical characteristics including strength and perceived exertion, and psychological health, including music performance anxiety (MPA), workplace satisfaction, and bullying. Physical characteristics and performance-related musculoskeletal profiles were similar for most factors on the detailed survey completed by orchestra members. The exceptions were that pit musicians demonstrated greater shoulder and elbow strength, while mixed-workload orchestra musicians had greater flexibility Significantly more exertion was reported by pit musicians when rehearsing and performing. Stage/pit musicians reported less physical exertion when performing in the pit compared with performing on stage. Severity of MPA was significantly greater in pit musicians than mixed orchestra musicians. Pit musicians also reported more frequent bullying and lower job satisfaction compared with stage musicians. There were few differences in the objective physical measures between musicians in the different orchestra types. However, pit musicians appear more psychologically vulnerable and less satisfied with their work than musicians from the other two orchestra types. The physical and psychological characteristics of musicians who perform in different orchestra types have not been adequately

Critical pitting temperature for Type 254 SMO stainless steel in chloride solutions

International Nuclear Information System (INIS)

Abd El Meguid, E.A.; Abd El Latif, A.A.

2007-01-01

The variation with time of the open circuit potential of high molybdenum containing stainless steel (Type 254 SMO) was measured in 4% sodium chloride solution in the temperatures range 30-100 deg. C. The plot of steady state potentials as function of temperature showed an inflection at 50 deg. C, attributed to the decrease of oxygen solubility in test solution above 50 deg. C. Potentiodynamic cycling anodic polarization technique was used to determine the critical pitting potential (E pit ) and the critical protection potential (E prot ) of the steel in 4-30% NaCl solutions at temperatures between 30 and 100 deg. C. By plotting the two values versus solution temperature, the corresponding critical pitting (CPT) and the critical protection (CPrT) temperatures were determined. Both parameters decreased with increasing chloride content. Above the CPT, E pit and E prot decreased linearly with log[Cl - ]. The addition of bromide ions to the solution shifted both E pit and E prot towards positive values. In 4% NaCl, E pit increased linearly with pH in the range 1-10. The combined effect of chloride ion concentration and pH on the morphology of the pits was examined by scanning electron microscopy (SEM) following potentiodynamic cycling anodic polarization

CHerenkov detectors In mine PitS (CHIPS) Letter of Intent to FNAL

Energy Technology Data Exchange (ETDEWEB)

Adamson, P. [Fermi National Accelerator Laboratory (FNAL), Batavia, IL (United States); Austin, J. [Univ. of Minnesota, Duluth, MN (United States); Cao, S. V. [Univ. of Texas, Austin, TX (United States); Coelho, J. A. B. [Tufts Univ., Medford, MA (United States); Davies, G. S. [Iowa State Univ., Ames, IA (United States); Evans, J. J. [Univ. of Manchester (United Kingdom); Guzowski, P. [Univ. of Manchester (United Kingdom); Habig, A. [Univ. of Minnesota, Duluth, MN (United States); Holin, A. [Univ. College London, London (United Kingdom); Huang, J. [Univ. of Texas, Austin, TX (United States); Johnson, R. [Univ. of Cincinnati, OH (United States); St. John, J. [Univ. of Cincinnati, OH (United States); Kreymer, A. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Kordosky, M. [College of William and Mary, Williamsburg, VA (United States); Lang, K. [Univ. of Texas, Austin, TX (United States); Marshak, M. L. [Univ. of Minnesota, Minneapolis, MN (United States); Mehdiyev, R. [Univ. of Texas, Austin, TX (United States); Meier, J. [Univ. of Minnesota, Minneapolis, MN (United States); Miller, W. [Univ. of Minnesota, Minneapolis, MN (United States); Naples, D. [Univ. of Pittsburgh, PA (United States); Nelson, J. K. [College of William and Mary, Williamsburg, VA (United States); Nichol, R. J. [Univ. College London, London (United Kingdom); Patterson, R. B. [California Inst. of Technology (CalTech), Pasadena, CA (United States); Paolone, V. [Univ. of Pittsburgh, PA (United States); Pawloski, G. [Univ. of Minnesota, Minneapolis, MN (United States); Perch, A. [Univ. College London, London (United Kingdom); Pfutzner, M. [Univ. College London, London (United Kingdom); Proga, M. [Univ. of Texas, Austin, TX (United States); Qian, X. [Brookhaven National Lab. (BNL), Upton, NY (United States); Radovic, A. [Univ. College London, London (United Kingdom); Sanchez, M. C. [Iowa State Univ., Ames, IA (United States); Schreiner, S. [Univ. of Minnesota, Minneapolis, MN (United States); Soldner-Rembold, S. [Univ. of Manchester (United Kingdom); Sousa, A. [Univ. of Cincinnati, OH (United States); Thomas, J. [Univ. College London, London (United Kingdom); Vahle, P. [College of William and Mary, Williamsburg, VA (United States); Wendt, C. [Univ. of Wisconsin, Madison, WI (United States); Whitehead, L. H. [Univ. College London, London (United Kingdom); Wojcicki, S. [Stanford Univ., CA (United States)

2013-12-30

This Letter of Intent outlines a proposal to build a large, yet cost-effective, 100 kton fiducial mass water Cherenkov detector that will initially run in the NuMI beam line. The CHIPS detector (CHerenkov detector In Mine PitS) will be deployed in a flooded mine pit, removing the necessity and expense of a substantial external structure capable of supporting a large detector mass. There are a number of mine pits in northern Minnesota along the NuMI beam that could be used to deploy such a detector. In particular, the Wentworth Pit 2W is at the ideal off-axis angle to contribute to the measurement of the CP violating phase. The detector is designed so that it can be moved to a mine pit in the LBNE beam line once that becomes operational.

Stochastic modeling of pitting corrosion: A new model for initiation and growth of multiple corrosion pits

International Nuclear Information System (INIS)

Valor, A.; Caleyo, F.; Alfonso, L.; Rivas, D.; Hallen, J.M.

2007-01-01

In this work, a new stochastic model capable of simulating pitting corrosion is developed and validated. Pitting corrosion is modeled as the combination of two stochastic processes: pit initiation and pit growth. Pit generation is modeled as a nonhomogeneous Poisson process, in which induction time for pit initiation is simulated as the realization of a Weibull process. In this way, the exponential and Weibull distributions can be considered as the possible distributions for pit initiation time. Pit growth is simulated using a nonhomogeneous Markov process. Extreme value statistics is used to find the distribution of maximum pit depths resulting from the combination of the initiation and growth processes for multiple pits. The proposed model is validated using several published experiments on pitting corrosion. It is capable of reproducing the experimental observations with higher quality than the stochastic models available in the literature for pitting corrosion

Stochastic modeling of pitting corrosion: A new model for initiation and growth of multiple corrosion pits

Energy Technology Data Exchange (ETDEWEB)

Valor, A. [Facultad de Fisica, Universidad de La Habana, San Lazaro y L, Vedado, 10400 Havana (Cuba); Caleyo, F. [Departamento de Ingenieria, Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico)]. E-mail: fcaleyo@gmail.com; Alfonso, L. [Departamento de Ingenieria, Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico); Rivas, D. [Departamento de Ingenieria, Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico); Hallen, J.M. [Departamento de Ingenieria, Metalurgica, IPN-ESIQIE, UPALM Edif. 7, Zacatenco, Mexico DF 07738 (Mexico)

2007-02-15

In this work, a new stochastic model capable of simulating pitting corrosion is developed and validated. Pitting corrosion is modeled as the combination of two stochastic processes: pit initiation and pit growth. Pit generation is modeled as a nonhomogeneous Poisson process, in which induction time for pit initiation is simulated as the realization of a Weibull process. In this way, the exponential and Weibull distributions can be considered as the possible distributions for pit initiation time. Pit growth is simulated using a nonhomogeneous Markov process. Extreme value statistics is used to find the distribution of maximum pit depths resulting from the combination of the initiation and growth processes for multiple pits. The proposed model is validated using several published experiments on pitting corrosion. It is capable of reproducing the experimental observations with higher quality than the stochastic models available in the literature for pitting corrosion.

Blasting as a method for abandoned mine land reclamation

International Nuclear Information System (INIS)

Workman, J.L.; Fletcher, L.R.

1991-01-01

Blasting methods have been proposed for reclaiming abandoned underground coal mine sites having unstable conditions. The objective of blasting is twofold: the permanent stabilization of an area by the collapse of underground workings to prevent any future subsidence, and the use of blasting to close existing sinkholes. This paper presents the results of two research projects funded by the Bureau of Mines Abandoned Mine Land Research Program to investigate the feasibility of blasting to assist in the reclamation of shallow abandoned coal mine sites. Blasting tests were conducted at Beulah, North Dakota and at Scobey, Montana, involving different configurations. The first test was a 10-acre site where blasting was used to collapse regular room and pillar panels for which good mine layout information was available. The second test involved a one acre site containing very irregular workings for which there was little available information. Finally, blasting techniques were used to close 13 individual vertical openings. The depths to the coal seams were 60 feet or less at all sites. When blasting for Abandoned Mine Land Reclamation, material must be cast downward into the abandoned developments or laterally into the sinkhole. Designs based on cratering concepts and spherical charges worked well. The blasting techniques successfully collapsed and stabilized the test areas. Cost of reclamation for the two test sites are presented. Data from blast vibration monitoring are presented because control of vibrations is of concern when mitigation efforts are conducted near homes

Estimating disperser abundance using open population models that incorporate data from continuous detection PIT arrays

Science.gov (United States)

Dzul, Maria C.; Yackulic, Charles B.; Korman, Josh

2017-01-01

Autonomous passive integrated transponder (PIT) tag antenna systems continuously detect individually marked organisms at one or more fixed points over long time periods. Estimating abundance using data from autonomous antennae can be challenging, because these systems do not detect unmarked individuals. Here we pair PIT antennae data from a tributary with mark-recapture sampling data in a mainstem river to estimate the number of fish moving from the mainstem to the tributary. We then use our model to estimate abundance of non-native rainbow trout Oncorhynchus mykiss that move from the Colorado River to the Little Colorado River (LCR), the latter of which is important spawning and rearing habitat for federally-endangered humpback chub Gila cypha. We estimate 226 rainbow trout (95% CI: 127-370) entered the LCR from October 2013-April 2014. We discuss the challenges of incorporating detections from autonomous PIT antenna systems into mark-recapture population models, particularly in regards to using information about spatial location to estimate movement and detection probabilities.

Strategic Mine Planning: A SWOT Analysis Applied to KOV Open Pit Mine in the Democratic Republic of Congo

OpenAIRE

Patrick May Mukonki

2017-01-01

KOV pit (Kamoto Oliveira Virgule) is located 10 km from Kolwezi town, one of the mineral rich town in the Lualaba province of the Democratic Republic of Congo. The KOV pit is currently operating under the Katanga Mining Limited (KML), a Glencore-Gecamines (a State Owned Company) join venture. Recently, the mine optimization process provided a life of mine of approximately 10 years withnice pushbacks using the Datamine NPV Scheduler software. In previous KOV pit studies, we recently outlined t...

Kinetics of growth of semi-spheric pittings in the vicinity repassivation potential depending on bulk concentration of activator anions

International Nuclear Information System (INIS)

Frejman, L.I.

1985-01-01

A general case of semi-spheric pittings development in aqueous solutions of electrolyte of NaCl or LiCl type at different values of C 0 , usually studied in the range approximately equal to 10 -5 -10 -3 g-ionxcm -3 (approximately equal to 10 -2 -10 0 g-ionxl -1 ), has been analyzed. On the basis of experimental data on participation of anion-activators and water molecules in the process of metal dissolution in pitting, and using the previously obtained equations, kinetics of open and closed semi-spheric pittings during galvanostatic anode polarization in neutral chloride solutions with different volumetric concentration of Cl - -ions (C 0 ) has been considered. In a general case the process kinetics is described by a complex equation, the boundary, more simple forms of which, correspond to the initial (A) and subsequent (B) stages of open pitting development, or to certain stable conditions of closed pitting development

Seasonal dynamics of the photosynthetic pigments content in Populus tremula L. leaves at the adaptation on an open-pit coal mine revegetating dump

Directory of Open Access Journals (Sweden)

Yu. V. Zagurskaya

2017-02-01

Full Text Available Seasonal dynamics of the basic photosynthetic pigments (a and b chlorophylls, carotenoids content in the samples of aspen Populus tremula during natural regeneration on a revegetating pit dump of a worked-out coal pit has been studied. The studies were conducted every ten days during the vegetation period in 2015 (June–September on the territory of «Yuzhniy» dump of «Kedrovskiy» open-pit coal mine (Kemerovo region. The pigment content was identified by the means of spectrophotometric detection. The content of photosynthetic pigments in aspen leaves was calculated on oven-dry weight of the leaves, as moisture aspen leaves can greatly vary, and the determination of accuracy of dry matter content higher than the for specific gravity of the sheet. No changes in visible absorption spectrum of acetone extracts indicating pheophytin formation in chlorophylls have been identified. For all variants the larger amount of b chlorophyll was contained in control samples. The largest differences in a/b chlorophylls and chlorophylls/carotenoids ratio were observed in the end of vegetation period. The ratio between a and b chlorophylls of aspen leaves in both cases by the end of the season was considerably lower. The adaptation of aspen photosynthetic system to the revegetating dump conditions was performed due to decrease in the total pigment content and the percent of b chlorophyll in their composition.

Detailed investigation of current transients from metastable pitting events on stainless steel - the transition to stability

International Nuclear Information System (INIS)

Pistorius, P.C.; Burstein, G.T.

1992-01-01

Current transients which result from metastable pitting events (on Type 304 stainless steel in an acidic solution containing 1 M Cl - ) are presented. A criterion for the stable growth of open hemispherical pits is developed; the criterion states that the product of current density and pit depth must exceed a certain minimum value, to sustain rapid dissolution. Analysis of the transients from metastable pits shows that these pits fall short of this minimum, as do stable pits initially. The growth of these pits thus requires the presence of another barrier to diffusion, which is thought to be a remnant of the passive film; this forms a flawed cover over the pit mouth. When this cover ruptures under the influence of osmotic pressure, the pit repassivates. Pits growing at higher current densities approach the minimum requirement for stable growth more closely. A ''pitting potential'' results from the effect that metastable pits formed at more positive potentials grow at higher current densities, and are thus more likely to grow into stable pits. The effect of potential on the current density does not result from either activation control or ohmic control; rather, the pits grow under diffusion control. A change, with potential, of the type of pit site which can be activated, causes the potential dependence of the distribution of current densities in metastable pits. Although the distribution of current densities changes with potential, each metastable pit grows under diffusion control with a current density which is independent of the potential; this is confirmed by polarisation tests on growing metastable pits

A New Algorithm for Determining Ultimate Pit Limits Based on Network Optimization

Directory of Open Access Journals (Sweden)

Ali Asghar Khodayari

2013-12-01

Full Text Available One of the main concerns of the mining industry is to determine ultimate pit limits. Final pit is a collection of blocks, which can be removed with maximum profit while following restrictions on the slope of the mine’s walls. The size, location and final shape of an open-pit are very important in designing the location of waste dumps, stockpiles, processing plants, access roads and other surface facilities as well as in developing a production program. There are numerous methods for designing ultimate pit limits. Some of these methods, such as floating cone algorithm, are heuristic and do not guarantee to generate optimum pit limits. Other methods, like Lerchs–Grossmann algorithm, are rigorous and always generate the true optimum pit limits. In this paper, a new rigorous algorithm is introduced. The main logic in this method is that only positive blocks, which can pay costs of their overlying non-positive blocks, are able to appear in the final pit. Those costs may be paid either by positive block itself or jointly with other positive blocks, which have the same overlying negative blocks. This logic is formulated using a network model as a Linear Programming (LP problem. This algorithm can be applied to two- and three-dimension block models. Since there are many commercial programs available for solving LP problems, pit limits in large block models can be determined easily by using this method.

Surface monitoring for pitting evolution into uniform corrosion on Cu-Ni-Zn ternary alloy in alkaline chloride solution: ex-situ LCM and in-situ SECM

Science.gov (United States)

Kong, Decheng; Dong, Chaofang; Zheng, Zhaoran; Mao, Feixiong; Xu, Aoni; Ni, Xiaoqing; Man, Cheng; Yao, Jizheng; Xiao, Kui; Li, Xiaogang

2018-05-01

The evolution of the corrosion process on Cu-Ni-Zn alloy in alkaline chloride solution was investigated by in-situ scanning electrochemical microscopy, X-ray photoelectron spectroscopy, and ex-situ laser confocal microscopy, and the effects of ambient temperature and polarization time were also discussed. The results demonstrated a higher pitting nucleation rate and lower pit growth rate at low temperature. The ratio of pit depth to mouth diameter decreased with increasing pit volume and temperature, indicating that pits preferentially propagate in the horizontal direction rather than the vertical direction owing to the presence of corrosion products and deposited copper. The surface current was uniform and stabilized at approximately 2.2 nA during the passive stage, whereas the current increased after the pits were formed with the maximum approaching 3 nA. Increasing the temperature led to an increase in porous corrosion products (CuO, Zn(OH)2, and Ni(OH)2) and significantly increased the rate of transition from pitting to uniform corrosion. Dezincification corrosion was detected by energy dispersive spectrometry, and a mechanism for pitting transition into uniform corrosion induced by dezincification at the grain boundaries is proposed.

Abandoned works program

International Nuclear Information System (INIS)

Arnott, A.

2007-01-01

Thousands of improperly abandoned or decommissioned oil and gas wells are threatening the purity of Ontario's source water. This presentation discussed an abandoned works program developed by the Ontario Ministry of Natural Resources. The abandoned works program was established in 2005 in order to plug old oil and gas wells. The program was designed to create a list of abandoned wells, develop a coherent policy, and formulate procurement and contracting protocols. Abandoned wells are defined as wells drilled prior to 1963 with no operator other than the current landowner. There are currently over 200 prioritized wells on the list. Twenty-six contracts have been issued for a total of 33 wells, and 19 wells have been plugged since the program's field operations began in 2006. However, the program is often challenged by the difficulties associated with determining where the wells are located. Many of the wells have been cut off and buried, and access is often dependent on weather conditions and road restrictions. There is also a shortage of contractors who have experience working with older wells. It was concluded that the program will expand by obtaining further funding and modifying its qualification criteria. tabs., figs

Ontario Hydro studies on copper corrosion under waste disposal conditions

International Nuclear Information System (INIS)

Lam, K.W.

1990-01-01

The corrosion rate of copper is generally greater in aerated solutions containing sulphide; also, in the presence of sulphide there is the fear that pitting may occur. Experiments have been carried out to study the corrosion of copper in deaerated groundwater/bentonite slurries with and without added sulphide for exposure periods from two months to one year. The groundwater contains 6500 ppm of chloride and 1000 ppm of sulphate. Tests were also performed in the presence of a 150 rad/h radiation field. In deaerated slurries at 75C the corrosion rate is less than 2 μm/a. With one addition of 10 mg/l sulphide, the rate increases by a factor of ten. With daily sulphide additions to deaerated solutions the corrosion rate initially falls but then rises and stabilizes after 15 days. In aerated solutions the corrosion increases over the first 25 days and then stabilizes. The corrosion rate of copper reached a steady value in 15 to 30 days. Rates are higher in aerated solutions, but the effect of adding sulphide is not so marked in aerated solutions as in unaerated solutions. The highest corrosion rate, less than 150 μm/a, was observed in aerated slurries saturated with sulphide. For deaerated solutions in the absence of sulphide the corrosion rate increases with temperature, but in aerated solutions the rate decreases. For solutions containing added sulphide the influence of temperature is negligible. The effect of a radiation field may be beneficial; in the presence of a radiation field the corrosion rate is less than 20 μm/a. After descaling the coupons showed a high density of irregularly shaped pits both in the presence and absence of sulphide, resulting from intergranular attack. The pitting factor for the highest corrosion rate is around 15

Drillers and mill operators in an open-pit gold mine are at risk for impaired lung function.

Science.gov (United States)

Vinnikov, Denis

2016-01-01

Occupational studies of associations of exposures with impaired lung function in mining settings are built on exposure assessment and far less often on workplace approach, so the aim of this study was to identify vulnerable occupational groups for early lung function reduction in a cohort of healthy young miners. Data from annual screening lung function tests in gold mining company in Kyrgyzstan were linked to occupations. We compared per cent predicted forced expiratory volume in one second (FEV1), forced vital capacity (FVC) and FEV1/FVC between occupational groups and tested selected occupations in multivariate regression adjusted for smoking and work duration for the following outcomes: FEV1 open-pit mine for reduced lung function. Occupational medical clinic at site should follow-up workers in these occupations with depth and strongly recommend smoking cessation.

Pitting corrosion behaviour study of aluminium matrix composites (A3xx.x/SiCp)

International Nuclear Information System (INIS)

Pardo, A.; Merino, M. C.; Merino, S.; Lopez, M. D.; Viejo, F.; Carboneras, M.; Arrabal, R.

2004-01-01

The influence of the SiCp proportion on the pitting corrosion of A3xx.x/SiC/xxp composites was studies by means of potenciodinamic polarization and double cyclic polarization in saline environment at 25 degree centigrade A360/SiC/xxp matrix does not contain copper, whereas the A380/SiC/xxp matric contains 1,39-1,44 wt %Cu. The kinetic study was carried out by gravimetric measurements. The nature of corrosion products was analysed by low angle XRD and Scanning Electron Microscopy (SEM). The corrosion is due to nucleation and growth of Al 2 O 3 -3H 2 O on the material surface. The corrosion increases with the reinforcement proportion, chloride concentration and copper content. (Author) 10 refs

A probability distribution model of tooth pits for evaluating time-varying mesh stiffness of pitting gears

Science.gov (United States)

Lei, Yaguo; Liu, Zongyao; Wang, Delong; Yang, Xiao; Liu, Huan; Lin, Jing

2018-06-01

Tooth damage often causes a reduction in gear mesh stiffness. Thus time-varying mesh stiffness (TVMS) can be treated as an indication of gear health conditions. This study is devoted to investigating the mesh stiffness variations of a pair of external spur gears with tooth pitting, and proposes a new model for describing tooth pitting based on probability distribution. In the model, considering the appearance and development process of tooth pitting, we model the pitting on the surface of spur gear teeth as a series of pits with a uniform distribution in the direction of tooth width and a normal distribution in the direction of tooth height, respectively. In addition, four pitting degrees, from no pitting to severe pitting, are modeled. Finally, influences of tooth pitting on TVMS are analyzed in details and the proposed model is validated by comparing with a finite element model. The comparison results show that the proposed model is effective for the TVMS evaluations of pitting gears.

A Comprehensive Pitting Study of High Velocity Oxygen Fuel Inconel 625 Coating by Using Electrochemical Testing Techniques

Science.gov (United States)

Niaz, Akbar; Khan, Sajid Ullah

2016-01-01

In the present work, Inconel 625 was coated on a mild steel substrate using a high velocity oxygen fuel coating process. The pitting propensity of the coating was tested by using open circuit potential versus time, potentiodynamic polarization, electrochemical potentiokinetic reactivation, and scanning electrochemical microscopy. The pitting propensity of the coating was compared with bulk Inconel 625 alloy. The results confirmed that there were regions of different electrochemical activities on the coating which have caused pitting corrosion.

Public exposure to hazards associated with natural radioactivity in open-pit mining in Ghana.

Science.gov (United States)

Darko, E O; Faanu, A; Awudu, A R; Emi-Reynolds, G; Yeboah, J; Oppon, O C; Akaho, E H K

2010-01-01

The results of studies carried out on public exposure contribution from naturally occurring radioactive materials (NORMS) in two open-pit mines in the Western and Ashanti regions of Ghana are reported. The studies were carried out under International Atomic Energy Agency-supported Technical Co-operation Project GHA/9/005. Measurements were made on samples of water, soil, ore, mine tailings and air using gamma spectrometry. Solid-state nuclear track detectors were used for radon concentration measurements. Survey was also carried out to determine the ambient gamma dose rate in the vicinity of the mines and surrounding areas. The effective doses due to external gamma irradiation, ingestion of water and inhalation of radon and ore dusts were calculated for the two mines. The average annual effective dose was found to be 0.30 +/- 0.06 mSv. The result was found to be within the levels published by other countries. The study provides a useful information and data for establishing a comprehensive framework to investigate other mines and develop guidelines for monitoring and control of NORMS in the mining industry and the environment as a whole in Ghana.

Thermodynamic data for copper. Implications for the corrosion of copper under repository conditions

International Nuclear Information System (INIS)

Puigdomenech, I.; Taxen, C.

2000-08-01

The stability of copper canisters has a central role in the safety concept for the planned nuclear spent fuel repository in Sweden. The corrosion of copper canisters will be influenced by the chemical and physical environment in the near-field of the repository, and thermodynamic equilibrium calculations provide the basis for understanding this system. Thermodynamic data have been selected in this work for solids and aqueous species in the system: Cu - H 2 O - H + - H 2 - F - - Cl - - S 2- - SO 4 2- - NO 3 - - NO 2 - - NH 4 + PO 4 3- - CO 3 2+ . For some reactions and compounds, for which no experimental information on temperature effects was available, entropy and heat capacity values have been estimated. The compiled data were used to calculate thermodynamic equilibria for copper systems up to 100 deg C. The stability of copper in contact with granitic groundwaters has been illustrated using chemical equilibrium diagrams, with he following main conclusions: Dissolved sulphide and O 2 in groundwater are the most damaging components for copper corrosion. If available, HS - will react quantitatively with copper to form a variety of sulphides. However, sulphide concentrations in natural waters are usually low, because it forms sparingly soluble solids with transition metals, including Fe(II), which is wide-spread in reducing environments. Chloride can affect negatively copper corrosion. High concentrations (e.g., [Cl - ]TOT > 60 g/l) may be unfavourable for the general corrosion of copper in combination with in the following circumstances: Low pH ( + . The negative effects of Cl - are emphasised at higher temperatures. The chloride-enhancement of general corrosion may be beneficial for localised corrosion: pitting and stress corrosion cracking. The concept of redox potential, E H , has been found to be inadequate to describe copper corrosion in a nuclear repository. The available amounts of oxidants/reductants, and the stoichiometry of the corrosion reactions are

Tank Riser Pit Decontamination System (Pit Viper) Return on Investment and Break-Even Analysis

International Nuclear Information System (INIS)

Young, Joan K.; Weimar, Mark R.; Balducci, Patrick J.; Fassbender, Linda L.; Hernandez, Melissa

2003-01-01

This study assessed the cost benefit of Pit Viper deployment for 80 tank farm pits between October 1, 2003 and September 30, 2012 under the technical baseline for applicable double-shell tank (DST) and single-shell tank (SST) projects. After this assessment had been completed, the U.S. Department of Energy (DOE) Richland Operations Office (RL) and Office of River Protection (ORP) published the Hanford Performance Management Plan (August 2003), which accelerated the schedule for SST retrieval. Then, DOE/CH2M HILL contract modification M064 (October 2002) and The Integrated Mission Acceleration Plan (March 2003) further accelerated SST retrieval and closure schedules. Twenty-six to 40 tanks must be retrieved by 2006. Thus the schedule for SST pit entries is accelerated and the number of SST pit entries is increased. This study estimates the return on investment (ROI) and the number of pits where Pit Viper deployment would break even or save money over current manual practices. The results of the analysis indicate a positive return on the federal investment for deployment of the Pit Viper provided it is used on a sufficient number of pits

A Difference-In-Differences Study of the Effects of a New Abandoned Building Remediation Strategy on Safety

Science.gov (United States)

Michelle C. Kondo; Danya Keene; Bernadette C. Hohl; John M. MacDonald; Charles C. Branas

2015-01-01

Vacant and abandoned buildings pose significant challenges to the health and safety of communities. In 2011 the City of Philadelphia began enforcing a Doors and Windows Ordinance that required property owners of abandoned buildings to install working doors and windows in all structural openings or face significant fines. We tested the effects of the new ordinance on...

Pit Water Storage Ottrupgaard

DEFF Research Database (Denmark)

Heller, Alfred

2000-01-01

The pit water storage, a seasonal thermal storage, was built in 1993 with floating lid and hybrid clay-polymer for pit lining. The storage was leaking severe and solutions were to be found. In the paper solutions for pit lining and floating lids are discussed, cost estimations given and coming...

Spatial distribution of environmental risk associated to a uranium abandoned mine (Central Portugal)

Science.gov (United States)

Antunes, I. M.; Ribeiro, A. F.

2012-04-01

The abandoned uranium mine of Canto do Lagar is located at Arcozelo da Serra, central Portugal. The mine was exploited in an open pit and produced about 12430Kg of uranium oxide (U3O8), between 1987 and 1988. The dominant geological unit is the porphyritic coarse-grained two-mica granite, with biotite>muscovite. The uranium deposit consists of two gaps crushing, parallel to the coarse-grained porphyritic granite, with average direction N30°E, silicified, sericitized and reddish jasperized, with a width of approximately 10 meters. These gaps are accompanied by two thin veins of white quartz, 70°-80° WNW, ferruginous and jasperized with chalcedony, red jasper and opal. These veins are about 6 meters away from each other. They contain secondary U-phosphates phases such as autunite and torbernite. Rejected materials (1000000ton) were deposited on two dumps and a lake was formed in the open pit. To assess the environmental risk of the abandoned uranium mine of Canto do Lagar, were collected and analysed 70 samples on stream sediments, soils and mine tailings materials. The relation between samples composition were tested using the Principal Components Analysis (PCA) (multivariate analysis) and spatial distribution using Kriging Indicator. The spatial distribution of stream sediments shows that the probability of expression for principal component 1 (explaining Y, Zr, Nb, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Hf, Th and U contents), decreases along SE-NW direction. This component is explained by the samples located inside mine influence. The probability of expression for principal component 2 (explaining Be, Na, Al, Si, P, K, Ca, Ti, Mn, Fe, Co, Ni, Cu, As, Rb, Sr, Mo, Cs, Ba, Tl and Bi contents), increases to middle stream line. This component is explained by the samples located outside mine influence. The spatial distribution of soils, shows that the probability of expression for principal component 1 (explaining Mg, P, Ca, Ge, Sr, Y, Zr, La, Ce, Pr

Suspension, abandonment, decontamination, and surface land reclamation of upstream oil and gas facilities : informational letter IL 98-2

International Nuclear Information System (INIS)

1998-01-01

This release of the Alberta Energy and Utilities Board (EUB) is intended to clarify the jurisdictional roles of Alberta Environmental Protection (AEP) and the EUB with regard to their respective responsibilities for the regulation of the suspension, abandonment, decontamination and surface land reclamation of active and inactive upstream oil and gas facilities. The EUB, AEP and industrial operators all have separate roles and responsibilities when active and inactive upstream facilities are suspended or reclaimed. In the future, industry operators will have more interaction with the AEP during the decontamination of a site, while the EUB will concentrate on pollution prevention and abandonment of non-economic facilities. All oilfield waste generated from suspension, abandonment, decontamination, and surface land reclamation of an active or inactive upstream oil and gas facility will fall under the jurisdiction of the EUB. Contaminated soils, sludges, and waters that are physically removed as a result of decontamination activities are considered to be oilfield wastes. The regulatory responsibility between the AEP and the EUB remains unchanged for the reclamation process of on-lease and off-lease spills, releases or pipeline breaks. Industry operators are no longer allowed to discharge any produced liquid to earthen pits or ponds and are encouraged to reclaim existing ones. 3 figs

A New Type of Inscribed Copper Plate from Indus Valley (Harappan Civilisation

Directory of Open Access Journals (Sweden)

Vasant Shinde

2014-10-01

Full Text Available A group of nine Indus Valley copper plates (c. 2600–2000 BC, discovered from private collections in Pakistan, appear to be of an important type not previously described. The plates are significantly larger and more robust than those comprising the corpus of known copper plates or tablets, and most significantly differ in being inscribed with mirrored characters. One of the plates bears 34 characters, which is the longest known single Indus script inscription. Examination of the plates with x-ray fluorescence (XRF spectrophotometry indicates metal compositions, including arsenical copper, consistent with Indus Valley technology. Microscopy of the metal surface and internal structure reveals detail such as pitting, microcrystalline structure, and corrosion, consistent with ancient cast copper artifacts. Given the relative fineness of the engraving, it is hypothesised that the copper plates were not used as seals, but have characteristics consistent with use in copper plate printing. As such, it is possible that these copper plates are by far the earliest known printing devices, being at least 4000 years old.

Stationary and transient thermal states of barometric pumping in the access pit of an underground quarry.

Science.gov (United States)

Perrier, Frédéric; Le Mouël, Jean-Louis

2016-04-15

The transition zone between free and underground atmospheres hosts spectacular phenomena, as demonstrated by temperature measurements performed in the 4.6m diameter and 20m deep vertical access pit of an abandoned underground quarry located in Vincennes, near Paris. In summer, a stable stratification of the atmosphere is maintained, with coherent temperature variations associated with atmospheric pressure changes, with a barometric tide S2 larger than 0.1°C peak to peak. When the winter regime of turbulent cold air avalanches is initiated, stratification with pressure induced signals can be restored transiently in the upper part of the pit, while the lower part remains fully mixed and insensitive to pressure variations. The amplitude of the pressure to temperature transfer function increases with frequency below 5×10(-4)Hz, with values at 3×10(-5)Hz varying from 0.1°C·hPa(-1) at the bottom up to 2°C·hPa(-1) towards the top of the pit. These temperature variations are accounted for by cave breathing, which is pressure induced motion of air amplified by the large volume of the quarry. This understanding is supported by a numerical model including advective heat transport, heat diffusion, and heat exchange with the pit walls. Mean lifetime in the pit is of the order of 9 to 13h, and barometric pumping results in an effective ventilation rate of the quarry of the order of 10(-7)s(-1). This study illustrates the important role of barometric pumping in heat and matter transport between atmosphere and lithosphere. The resulting stationary and transient states, revealed in this pit, are probably a general feature of functioning interface systems, and therefore are an important aspect to consider in problems of contaminant transport, or the preservation of precious heritage such as rare ecosystems or painted caves. Copyright © 2016 Elsevier B.V. All rights reserved.

Field measurements of mixed exposure of operators to radioactive aerosol, gas and quartz in confinement of mining equipment cabs during open-pit mining of high-grade uranium ores

International Nuclear Information System (INIS)

Yoshida, K.; Atiemo, M.A.; Markham, J.W.

1982-07-01

A series of field measurements of miners mixed exposure to radon and daughters, uranium ore dust and respirable quartz, was conducted in an open-pit mine in Northern Saskatchewan during 1980-81. Control of radon gas levels in the mining equipment cabs is required. Dust may be reduced by minimizing the resuspension of dust from contaminated surfaces within the cabs

Adsorption mechanisms of removing heavy metals and dyes from aqueous solution using date pits solid adsorbent

International Nuclear Information System (INIS)

Al-Ghouti, Mohammad A.; Li, Juiki; Salamh, Yousef; Al-Laqtah, Nasir; Walker, Gavin; Ahmad, Mohammad N.M.

2010-01-01

A potential usefulness of raw date pits as an inexpensive solid adsorbent for methylene blue (MB), copper ion (Cu 2+ ), and cadmium ion (Cd 2+ ) has been demonstrated in this work. This work was conducted to provide fundamental information from the study of equilibrium adsorption isotherms and to investigate the adsorption mechanisms in the adsorption of MB, Cu 2+ , and Cd 2+ onto raw date pits. The fit of two models, namely Langmuir and Freundlich models, to experimental data obtained from the adsorption isotherms was checked. The adsorption capacities of the raw date pits towards MB and both Cu 2+ and Cd 2+ ions obtained from Langmuir and Freundlich models were found to be 277.8, 35.9, and 39.5 mg g -1 , respectively. Surface functional groups on the raw date pits surface substantially influence the adsorption characteristics of MB, Cu 2+ , and Cd 2+ onto the raw date pits. The Fourier transform infrared spectroscopy (FTIR) studies show clear differences in both absorbances and shapes of the bands and in their locations before and after solute adsorption. Two mechanisms were observed for MB adsorption, hydrogen bonding and electrostatic attraction, while other mechanisms were observed for Cu 2+ and Cd 2+ . For Cu 2+ , binding two cellulose/lignin units together is the predominant mechanism. For Cd 2+ , the predominant mechanism is by binding itself using two hydroxyl groups in the cellulose/lignin unit.

The United States pit disassembly and conversion project -- Meeting the MOX fuel specification

International Nuclear Information System (INIS)

Nelson, T.O.; James, C.A.; Kolman, D.G.

1998-01-01

The US is actively involved in demonstrating the disassembly of nuclear weapons pits to an unclassified form readied for disposition. The MOX option is the most likely path forward for plutonium that originated from nuclear weapon pits. The US demonstration line for pit disassembly and conversion is known as ARIES, the advanced recovery and integrated extraction system. The ARIES demonstration line is being used to gather data in an integrated fashion of the technologies needed for pit disassembly and conversion. These activities include the following modules: pit bisection, hydride-dehydride, oxide conversion, canning, electrolytic decontamination, and nondestructive assay (NDA). Pit bisection swages in a pit in half. Hydride-dehydride converts the pit plutonium metal to an unclassified metal button. To convert the plutonium metal to an oxide the US is investigating a number of options. The primary oxide conversion approach involves variations of combining plutonium hydriding and subsequent oxidation. Another approach is to simply oxidize the metal under controlled conditions-direct metal oxidation (DMO). To remove the gallium from the plutonium oxide, a thermal distillation approach is being used. These pyrochemical approaches will substantially reduce the wastes produced for oxide conversion of weapon plutonium, compared to traditional aqueous processing. The packaging of either the plutonium metal or oxide to long term storage criteria involves the canning and electrolytic decontamination modules. The NDA suite of instruments is then used to assay the material in the containers, which enables international verification without the need to open the containers and repackage them. All of these processes are described

The mine planning process for an open-pit diamond mining operation - a case study on Letseng diamond mine in Lesotho

OpenAIRE

Madowe, A.

2013-01-01

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves...

Abandonment (field decommissioning): The legal requirements

International Nuclear Information System (INIS)

Roberts, M.

1994-01-01

The main areas to be considered in relation to the abandonment of offshore installations are: (1) the legal requirements to be imposed in relation to abandonment, this will include consideration of English, Norwegian and Dutch law as well as international law; (2) how licensees may protect themselves against joint and several liability for performance of their legal obligations in relation to abandonment by the provision of security; and (3) consideration of practical examples of abandonment such as the abandonment of the Piper Alpha platform on the UK continental shelf and the K13-D platform on the Dutch continental shelf. This paper considers only abandonment of offshore installations as very different considerations apply onshore and applies only to Europe, though the international treaties will also apply elsewhere

Field emission response from multi-walled carbon nanotubes grown on electrochemically engineered copper foil

Energy Technology Data Exchange (ETDEWEB)

Tripathi, Amit Kumar; Jain, Vaibhav [Nanomaterials and Applications Lab., Department of Metallurgical and Materials Engineering, Indian Institute of Technology Roorkee, Roorkee, 247667, Uttarakhand (India); Saini, Krishna [Nanomaterials and Applications Lab., Department of Metallurgical and Materials Engineering, Indian Institute of Technology Roorkee, Roorkee, 247667, Uttarakhand (India); Centre of Excellence: Nanotechnology, Indian Institute of Technology Roorkee, Roorkee, 247667, Uttarakhand (India); Lahiri, Indranil, E-mail: indrafmt@iitr.ac.in [Nanomaterials and Applications Lab., Department of Metallurgical and Materials Engineering, Indian Institute of Technology Roorkee, Roorkee, 247667, Uttarakhand (India); Centre of Excellence: Nanotechnology, Indian Institute of Technology Roorkee, Roorkee, 247667, Uttarakhand (India)

2017-02-01

Exciting properties of carbon nanotube has proven it to be a promising candidate for field emission applications, if its processing cost can be reduced effectively. In this research, a new electrochemical technique is proposed for growing carbon nanotubes in selective areas by thermal chemical vapour deposition. In this process, electrochemical processing is used to create localized pits and deposition of catalysts, which act as roots to support growth and alignment of the CNTs on copper substrate. CNTs grown thus were characterized and studied using scanning electron microscope, transmission electron microscope and Raman spectroscopy, elucidating presence of multiwall carbon nanotubes (MWCNT). These CNT emitters have comparatively lower turn-on field and higher field enhancement factor. - Highlights: • Electrochemical pitting for localized carbon nanotube growth is proposed. • Electrochemical pitting method shows patterning effect on the substrate. • Size and density of pits depend on voltage, pH and temperature. • CNTs thus grown shows good field emission response.

Chemicals, metals, and pesticide pits waste unit low induction number electromagnetic survey

Energy Technology Data Exchange (ETDEWEB)

Cumbest, R.J.; Mohon, D.

1995-06-01

An electromagnetic survey was conducted at the Chemicals, Metals, and Pesticide Waste Unit to identify any buried metallic objects that may be present in the materials used to fill and cover the pits after removal of pit debris. The survey was conducted with a Geonics EM-31 Terrain Conductivity Meter along north - south oriented traverses with 5-ft station intervals to produce a 5-ft by 5-ft square grid node pattern. Both conductivity and in-phase components were measured at each station for vertical dipole orientation with the common axis of the dipoles in the north - south and east - west orientations. The conductivity data clearly show elevated conductivities (2.1 to 7.0 mS/m) associated with the material over the pits, as compared with the surrounding area that is characterized by lower conductivities (1 to 2 mS/m). This is probably the result of the higher clay content of the fill material relative to the surrounding area, which has a higher sand to clay ratio and the presence of a plastic cover beneath the fill that has probably trapped water. Many metal objects are present in the survey area including manhole covers, monitoring well heads, metal, signs, drain culverts, abandoned wells, and BP waste unit marker balls. AU of these exhibit associated conductivity and in-phase anomalies of various magnitude. In addition to these anomalies that can be definitely associated with surface sources, conductivity and in-phase anomalies are also present with no obvious surface source. These anomalies are probably indicative of subsurface buried metallic objects. A high concentration of these objects appears to be present in the southwest corner of the survey area.

NELL-1 increases pre-osteoblast mineralization using both phosphate transporter Pit1 and Pit2

Energy Technology Data Exchange (ETDEWEB)

Cowan, Catherine M. [Department of Bioengineering, University of California, Los Angeles, 420 Westwood Plaza,7523 Boelter Hall, Los Angeles, CA 90095 (United States); Dental and Craniofacial Research Institute and Section of Orthodontics, School of Dentistry, University of California, Los Angeles, 40833 Le Conte Ave, Los Angeles, CA 90095 (United States); Zhang, Xinli; James, Aaron W.; Mari Kim, T.; Sun, Nichole [Dental and Craniofacial Research Institute and Section of Orthodontics, School of Dentistry, University of California, Los Angeles, 40833 Le Conte Ave, Los Angeles, CA 90095 (United States); Wu, Benjamin [Department of Bioengineering, University of California, Los Angeles, 420 Westwood Plaza,7523 Boelter Hall, Los Angeles, CA 90095 (United States); Dental and Craniofacial Research Institute and Section of Orthodontics, School of Dentistry, University of California, Los Angeles, 40833 Le Conte Ave, Los Angeles, CA 90095 (United States); Ting, Kang [Dental and Craniofacial Research Institute and Section of Orthodontics, School of Dentistry, University of California, Los Angeles, 40833 Le Conte Ave, Los Angeles, CA 90095 (United States); Soo, Chia, E-mail: bsoo@ucla.edu [UCLA and Orthopaedic Hospital Department of Orthopaedic Surgery and the Orthopaedic, Hospital Research Center, University of California, Los Angeles, 2641 Charles E. Young Dr. South, Los Angeles, CA 90095 (United States)

2012-06-08

Highlights: Black-Right-Pointing-Pointer NELL-1 accelerates extracellular matrix mineralization in MC3T3-E1 pre-osteoblasts. Black-Right-Pointing-Pointer NELL-1 significantly increases intracellular inorganic phosphate levels. Black-Right-Pointing-Pointer NELL-1 positively regulates osteogenesis but not proliferation in MC3T3-E1 cells. Black-Right-Pointing-Pointer NELL-1 regulates inorganic phosphate transporter activity. -- Abstract: NELL-1 is a potent osteoinductive molecule that enhances bone formation in multiple animal models through currently unidentified pathways. In the present manuscript, we hypothesized that NELL-1 may regulate osteogenic differentiation accompanied by alteration of inorganic phosphate (Pi) entry into the osteoblast via sodium dependent phosphate (NaPi) transporters. To determine this, MC3T3-E1 pre-osteoblasts were cultured in the presence of recombinant human (rh)NELL-1 or rhBMP-2. Analysis was performed for intracellular Pi levels through malachite green staining, Pit-1 and Pit-2 expression, and forced upregulation of Pit-1 and Pit-2. Results showed rhNELL-1 to increase MC3T3-E1 matrix mineralization and Pi influx associated with activation of both Pit-1 and Pit-2 channels, with significantly increased Pit-2 production. In contrast, Pi transport elicited by rhBMP-2 showed to be associated with increased Pit-1 production only. Next, neutralizing antibodies against Pit-1 and Pit-2 completely abrogated the Pi influx effect of rhNELL-1, suggesting rhNELL-1 is dependent on both transporters. These results identify one potential mechanism of action for rhNELL-1 induced osteogenesis and highlight a fundamental difference between NELL-1 and BMP-2 signaling.

NELL-1 increases pre-osteoblast mineralization using both phosphate transporter Pit1 and Pit2

International Nuclear Information System (INIS)

Cowan, Catherine M.; Zhang, Xinli; James, Aaron W.; Mari Kim, T.; Sun, Nichole; Wu, Benjamin; Ting, Kang; Soo, Chia

2012-01-01

Highlights: ► NELL-1 accelerates extracellular matrix mineralization in MC3T3-E1 pre-osteoblasts. ► NELL-1 significantly increases intracellular inorganic phosphate levels. ► NELL-1 positively regulates osteogenesis but not proliferation in MC3T3-E1 cells. ► NELL-1 regulates inorganic phosphate transporter activity. -- Abstract: NELL-1 is a potent osteoinductive molecule that enhances bone formation in multiple animal models through currently unidentified pathways. In the present manuscript, we hypothesized that NELL-1 may regulate osteogenic differentiation accompanied by alteration of inorganic phosphate (Pi) entry into the osteoblast via sodium dependent phosphate (NaPi) transporters. To determine this, MC3T3-E1 pre-osteoblasts were cultured in the presence of recombinant human (rh)NELL-1 or rhBMP-2. Analysis was performed for intracellular Pi levels through malachite green staining, Pit-1 and Pit-2 expression, and forced upregulation of Pit-1 and Pit-2. Results showed rhNELL-1 to increase MC3T3-E1 matrix mineralization and Pi influx associated with activation of both Pit-1 and Pit-2 channels, with significantly increased Pit-2 production. In contrast, Pi transport elicited by rhBMP-2 showed to be associated with increased Pit-1 production only. Next, neutralizing antibodies against Pit-1 and Pit-2 completely abrogated the Pi influx effect of rhNELL-1, suggesting rhNELL-1 is dependent on both transporters. These results identify one potential mechanism of action for rhNELL-1 induced osteogenesis and highlight a fundamental difference between NELL-1 and BMP-2 signaling.

Restoration of open pit lignite mining in the former GDR: lessons to be learnt from Zwenkau

Energy Technology Data Exchange (ETDEWEB)

Wiegand, U.; Schreck, P.; Schreiter, P.; Lerche, I.; Glaesser, W. [Centre for Environmental Research Leipzig-Halle (UFZ), Halle (Germany) Dept. of Hydrogeology

2003-07-01

The interactions have been investigated between the near-surface sediments of the sediment dumping at the Zwenkau open pit near Leipzig, used for extraction of lignite, and the produced mining water. These environmental impacts are the legacy of the energy policy of the former GDR. The pyrite oxidation that takes place in the overburden sediments causes the formation of an oxidation front and the pH-value of sediments falls to about 2 to 3 very soon after deposition. The primary mineral contents are destroyed and a considerable number of elements are mobilized that remain locally in the sediment pores. Because of the very weak seepage, rainfall remains in the alluvial areas as so called dump lakes. The dump lakes are very acidic because the rainwater transport the mobilized elements from the surface. Autochthonous and allochthonous formations of secondary minerals have been observed and analysed. A continuously ongoing interaction of exogenous and endogenous effects hinders the hydrological and geochemical equilibrium stabilization. What to do with such a 'moonscape' is considered in the conclusions. 21 refs., 8 figs.

Single pit propagation on austenitic stainless steel

International Nuclear Information System (INIS)

Heurtault, Stephane

2016-01-01

The electrochemical characterization of metastable events such as pitting corrosion of stainless steel in chloride electrolyte remains complex because many individual processes may occur simultaneously on the alloy surface. To overcome these difficulties, an experimental setup, the flow micro-device, has been developed to achieve the initiation of a single pit and to propagate the single pit in three dimensions. In this work, we take advantage of such a device in order to revisit the pitting process on a 316L stainless steel in a chloride - sulphate bulk. In a first step, the time evolution of the pit geometry (depth, radius) and the chemical evolution of the pit solution investigated using in situ Raman spectroscopy have shown that the pit depth propagation depends on the formation of a metal chloride and sulphate gel in the pit solution, and is controlled by the metallic cations diffusion from the pit bottom to the pit mouth. The pit radius growth is defined by the initial surface de-passivation, by the presence of a pit cover and by the gel development in the solution. all of these phenomena are function of applied potential and chemical composition of the solution. In a last step, it was demonstrated that a critical chloride concentration is needed in order to maintain the pit propagation. This critical concentration slightly increases with the pit depth. From statistical analysis performed on identical experiments, a zone diagram showing the pit stability as a function of the chloride concentration and the pit dimensions was built. (author) [fr

Thermodynamic data for copper. Implications for the corrosion of copper under repository conditions

Energy Technology Data Exchange (ETDEWEB)

Puigdomenech, I. [Royal Inst. of Tech., Stockholm (Sweden); Taxen, C. [Swedish Corrosion Inst., Stockholm (Sweden)

2000-08-01

The stability of copper canisters has a central role in the safety concept for the planned nuclear spent fuel repository in Sweden. The corrosion of copper canisters will be influenced by the chemical and physical environment in the near-field of the repository, and thermodynamic equilibrium calculations provide the basis for understanding this system. Thermodynamic data have been selected in this work for solids and aqueous species in the system: Cu - H{sub 2}O - H{sup +} - H{sub 2} - F{sup -} - Cl{sup -} - S{sup 2-} - SO{sub 4}{sup 2-} - NO{sub 3}{sup -} - NO{sub 2}{sup -} - NH{sub 4}{sup +} PO{sub 4}{sup 3-} - CO{sub 3}{sup 2+} . For some reactions and compounds, for which no experimental information on temperature effects was available, entropy and heat capacity values have been estimated. The compiled data were used to calculate thermodynamic equilibria for copper systems up to 100 deg C. The stability of copper in contact with granitic groundwaters has been illustrated using chemical equilibrium diagrams, with he following main conclusions: Dissolved sulphide and O{sub 2} in groundwater are the most damaging components for copper corrosion. If available, HS{sup -} will react quantitatively with copper to form a variety of sulphides. However, sulphide concentrations in natural waters are usually low, because it forms sparingly soluble solids with transition metals, including Fe(II), which is wide-spread in reducing environments. Chloride can affect negatively copper corrosion. High concentrations (e.g., [Cl{sup -}]TOT > 60 g/l) may be unfavourable for the general corrosion of copper in combination with in the following circumstances: Low pH (< 4 at 25 deg C, or < 5 at 100 deg C). The presence of other oxidants than H{sup +}. The negative effects of Cl{sup -} are emphasised at higher temperatures. The chloride-enhancement of general corrosion may be beneficial for localised corrosion: pitting and stress corrosion cracking. The concept of redox potential, E

Heat Treatment Optimization Studies on PIT Nb$_3$Sn Strand for the NED Project

CERN Document Server

Boutboul, T; den Ouden, A; Pedrini, D; Seeber, B; Volpini, G

2009-01-01

For the Next European Dipole (NED) program, a Powder-In-Tube (PIT) strand was successfully developed by SMI. This high-performance Nb$_{3}$Sn strand presents a non-copper critical current density of ~ 2500 A/mm2 at 12 T applied field and 4.2 K and a filament diameter around 50 µm. Extensive heat treatment optimization studies were performed in order to maximize both critical current and RRR, with a plateau temperature down to 625 oC and duration up to 400 hours. It appears that a critical current enhancement of ~ 10 % can be achieved for a reaction schedule of 320 hours at 625 oC with non-copper critical current density respectively exceeding 2700 and 1500 A/mm2 at 12 and 15 T (4.2 K). Thanks to this modified heat treatment, this strand completely fulfils the NED stringent specification.

Environmental impact of active and abandoned mines and metal smelters in Slovenia

Directory of Open Access Journals (Sweden)

Tomaž Budkovič

2003-06-01

Full Text Available Slovenia has long been known for its numerous mines and ore processing. From the times of the Roman Empire to now, 49 mines and open pits were opened, four of them were large (Idrija, Mežica – Topla, Litija and Žirovski vrh. There were also 25 oreprocessing plants and smelters, which were operating mostly in the vicinity of larger mines (Idrija, Žerjav, Celje. Due to the lack of written sources, we probably haven succeeded in making a complete list of them. There were 33 iron works operating in the vicinity ofmines and open pits, three large ones have further developed and are still operating (Jesenice, Ravne na Koroškem and Štore. As the ore processing capacities have far exceeded the capacities of the Slovenian mining, ore has long been imported and only processed in Slovenia. On the basis of the results of our investigations in the vicinity of larger mines and smelters we estimated that in Slovenia the areas in which critical limit for heavy metal content is exceeded sums up to about 80 km2.

Interacting Effects Induced by Two Neighboring Pits Considering Relative Position Parameters and Pit Depth

Directory of Open Access Journals (Sweden)

Yongfang Huang

2017-04-01

Full Text Available For pre-corroded aluminum alloy 7075-T6, the interacting effects of two neighboring pits on the stress concentration are comprehensively analyzed by considering various relative position parameters (inclination angle θ and dimensionless spacing parameter λ and pit depth (d with the finite element method. According to the severity of the stress concentration, the critical corrosion regions, bearing high susceptibility to fatigue damage, are determined for intersecting and adjacent pits, respectively. A straightforward approach is accordingly proposed to conservatively estimate the combined stress concentration factor induced by two neighboring pits, and a concrete application example is presented. It is found that for intersecting pits, the normalized stress concentration factor Ktnor increases with the increase of θ and λ and always reaches its maximum at θ = 90°, yet for adjacent pits, Ktnor decreases with the increase of λ and the maximum value appears at a slight asymmetric location. The simulations reveal that Ktnor follows a linear and an exponential relationship with the dimensionless depth parameter Rd for intersecting and adjacent cases, respectively.

The Hyrkkoelae native copper mineralization as a natural analogue for copper canisters

International Nuclear Information System (INIS)

Marcos, N.

1996-10-01

The Hyrkkoelae U-Cu mineralization is located in southwestern Finland, near the Palmottu analogue site. The age of the mineralization is estimated to be between 1.8 and 1.7 Ga. Petrological and mineralogical studies have demonstrated that this mineralization has many geological features that parallel those of the sites being considered for nuclear waste disposal in Finland. A particular feature is the existence of native copper and copper sulfides in open fractures in the near-surface zone. This allows us to study the native copper corrosion process in analogous conditions as expected to dominate in the nuclear fuel waste repository. The occurrence of uranyl compounds at these fractures permits also considerations about the sorption properties of the engineered barrier material (metallic copper) and its corrosion products. From the study of mineral assemblages or paragenesis, it appears that the formation of copper sulfide (djurleite, Cu 1.934 ) after native copper (Cu 0 ) under anoxic (reducing) conditions is enhanced by the availability of dissolved HS - in the groundwater circulating in open fractures in the near-surface zone. The minimum concentration of HS - in the groundwater is estimated to be of the order of 10 -5 M (∼ 10 -4 g/l) and the minimum pH value not lower than about 7.8 as indicated by the presence of calcite crystals in the same fracture. The present study is the first one that has been performed on findings of native copper in reducing, neutral to slightly alkaline groundwaters. Thus, the data obtained is of most relevance in improving models of anoxic corrosion of copper canisters. (orig.)

Prevention of Child Abandonment

OpenAIRE

Gaia, A.

2011-01-01

The aim of this work is to analyze the determinants of child abandonment in the city of Bra ov. The research is based on a new dataset collected on the field on mothers and pregnant women at risk of abandoning their child.

Composition of Whiskers Grown on Copper in Repository Environment

International Nuclear Information System (INIS)

Hermansson, Hans-Peter; Tarkpea, Peeter; Holgersson, Stellan

2001-11-01

There is a hypothesis that a special family of local attack on copper based on growth of whiskers of sulfide, oxide/hydroxide and also carbonate/malachite could appear in the repository environment. It was earlier demonstrated that such whiskers could grow in a laboratory simulated repository environment, containing sulfide. A suggested composition of whiskers has earlier been forwarded but was not demonstrated. In the present work whiskers and their substrates were grown and characterized by investigations with a combination of SEM-EDS, XRD and LRS (Laser Raman Spectroscopy) techniques. SEM-EDS was used to determine the morphology and an elemental composition and distribution of whiskers and their substrate. A special effort was made to find out if the whisker growth is of a local or global character. The phase status could be determined locally and globally by combining XRD and LRS techniques on whiskers and substrates. Ideally, LRS gives a phase resolution down to a radius of 1 μm on the sample surface. This is of great value as it is of interest to study if there are phase differences in different parts of a whisker. Such information is important to understand the whisker growth mechanism. Cylindrical samples of pure copper were prepared and exposed to the selected de-aerated model groundwater containing, among other ions, chloride and sulfide. Exposure was performed in sealed glass flasks under de-aerated conditions. After exposure the copper sample was investigated on the surface, in cross section and on whiskers using the mentioned techniques. The results show that a black, easily detached layer of corrosion products is formed on the sample surface. The corrosion layer was subdivided into at least five parallel strata (probably more) of different composition. Numerous small pits and shallow pitting attacks with a larger radius were observed in the copper metal and the metal surface was in general very rough. A multitude of very easily detached whiskers or

Possible cases of leprosy from the Late Copper Age (3780-3650 cal BC) in Hungary.

Science.gov (United States)

Köhler, Kitti; Marcsik, Antónia; Zádori, Péter; Biro, Gergely; Szeniczey, Tamás; Fábián, Szilvia; Serlegi, Gábor; Marton, Tibor; Donoghue, Helen D; Hajdu, Tamás

2017-01-01

At the Abony-Turjányos dűlő site, located in Central Hungary, a rescue excavation was carried out. More than 400 features were excavated and dated to the Protoboleráz horizon, at the beginning of the Late Copper Age in the Carpathian Basin, between 3780-3650 cal BC. Besides the domestic and economic units, there were two special areas, with nine-nine pits that differed from the other archaeological features of the site. In the northern pit group seven pits contained human remains belonging to 48 individuals. Some of them were buried carefully, while others were thrown into the pits. The aim of this study is to present the results of the paleopathological and molecular analysis of human remains from this Late Copper Age site. The ratio of neonates to adults was high, 33.3%. Examination of the skeletons revealed a large number of pathological cases, enabling reconstruction of the health profile of the buried individuals. Based on the appearance and frequency of healed ante- and peri mortem trauma, inter-personal (intra-group) violence was characteristic in the Abony Late Copper Age population. However other traces of paleopathology were observed on the bones that appear not to have been caused by warfare or inter-group violence. The remains of one individual demonstrated a rare set of bone lesions that indicate the possible presence of leprosy (Hansen's disease). The most characteristic lesions occurred on the bones of the face, including erosion of the nasal aperture, atrophy of the anterior nasal spine, inflammation of the nasal bone and porosity on both the maxilla and the bones of the lower legs. In a further four cases, leprosy infection is suspected but other infections cannot be excluded. The morphologically diagnosed possible leprosy case significantly modifies our knowledge about the timescale and geographic spread of this specific infectious disease. However, it is not possible to determine the potential connections between the cases of possible leprosy

Real -time dispatching modelling for trucks with different capacities in open pit mines / Modelowanie w czasie rzeczywistym przewozów ciężarówek o różnej ładowności w kopalni odkrywkowej

Science.gov (United States)

Ahangaran, Daryoush Kaveh; Yasrebi, Amir Bijan; Wetherelt, Andy; Foster, Patrick

2012-10-01

Application of fully automated systems for truck dispatching plays a major role in decreasing the transportation costs which often represent the majority of costs spent on open pit mining. Consequently, the application of a truck dispatching system has become fundamentally important in most of the world's open pit mines. Recent experiences indicate that by decreasing a truck's travelling time and the associated waiting time of its associated shovel then due to the application of a truck dispatching system the rate of production will be considerably improved. Computer-based truck dispatching systems using algorithms, advanced and accurate software are examples of these innovations. Developing an algorithm of a computer- based program appropriated to a specific mine's conditions is considered as one of the most important activities in connection with computer-based dispatching in open pit mines. In this paper the changing trend of programming and dispatching control algorithms and automation conditions will be discussed. Furthermore, since the transportation fleet of most mines use trucks with different capacities, innovative methods, operational optimisation techniques and the best possible methods for developing the required algorithm for real-time dispatching are selected by conducting research on mathematical-based planning methods. Finally, a real-time dispatching model compatible with the requirement of trucks with different capacities is developed by using two techniques of flow networks and integer programming.

Determination of Seismic Safety Zones during the Surface Mining Operation Development in the Case of the “Buvač” Open Pit

Directory of Open Access Journals (Sweden)

Vladimir Malbasic

2018-02-01

Full Text Available Determination of the blasting safety area is a very important step in the process of drilling and blasting works, and the preparation of solid rock materials for loading. Through monitoring and analysis of the negative seismic effects to the objects and infrastructures around and at the mine area, we were able to adapt the drilling and blasting parameters and organization of drilling and blasting operation according to the mining progress so that the affected infrastructures could be protected. This paper analyses the safety distances and model safety zones of drilling and blasting for the period 2013–2018 at the open pit at “Buvač”, Omarska. This mathematical calculation procedure can be used during the whole life of the mine. By monitoring of the blasting seismic influence in first years of the mine's work, as well as by using recorded vibration velocities, mathematical dependence of the important parameters can be defined. Additionally, the level and laws of distribution and intensity of the seismic activity can be defined. On one hand, those are known quantities of the explosive and the distances between blasting location and endangered objects. On the other hand, those are coefficients of the manner of blasting and the environment where blasting is done, K, as well as the coefficient of the weakening of seismic waves as they spread, n. With the usage of the allowed vibration velocities, based on certain safety criteria and mathematical formulas of laws of spreading and intensity of seismic influence for a concrete case, it is possible to calculate explosive quantities and distances, with numerically-defined values of parameter K and n. Minimum distances are calculated based on defined or projected explosive quantities. Additionally, we calculate the maximum allowed explosive quantities based on known distances which can be used based on projected drilling-blasting parameters. For the purpose of the planning of drilling and blasting

Compromises in orchestra pit design: A ten-year trench war in The Royal Theatre, Copenhagen

DEFF Research Database (Denmark)

Gade, Anders Christian; Mortensen, Bo

1998-01-01

of opera finally opened the way for a new renovation of the pit, which solved most of the problems. The paper describes the many lessons learned during the ten-year period in which the authors were involved with the case as acoustic consultants. Questions of how pit configuration influences mutual hearing......The ``old stage'' of The Royal Theatre in Copenhagen-a classical horseshoe theatre with an almost flat audience floor and four balcony levels—is the primary opera and ballet theatre in Denmark. In the early 1980s the orchestra pit was enlarged and its size made flexible. However, in the following...... years this new flexibility caused a formal battle between the orchestra, the singers, and management, because each group had different interests as to how the pit should be configured for each new production. In the 1990s, increased concern about the musicians' hearing and the increase in the popularity...

STRESSES AND DEFORMABILITY OF ROCK MASS UPON OPEN PIT EXPLOITATION OF DIMENSION STONE

Directory of Open Access Journals (Sweden)

Siniša Dunda

2003-12-01

Full Text Available The appearance of increased stresses and deformability of rock mass in the quarry of Zečevo (exploitation field of Selca – island of Brač has caused a considerable decrease of usability of mineral raw materials, which put into question the survival of the pit. Therefore the research and measurements of the state of stresses and deformability of rock mass within the pit were carried out. Besides detailed laboratory testings (testings on small samples performed were trial in-situ testings on large samples including the corresponding numerical analyses. The exploitation of dimension stone by sowing regularly shaped rectangular blocks has been proved to be appropriate for in-situ testing of bending strength. The paper presents the results of carried out laboratory testings, in-situ testings of bending strength including measuring of deformations after sowing cuts and numerical analyses by which the possible range of horizontal stresses was determined. Since for the case of massive rocks, for which the continuum concept is applied, there are no specifically defined methods of corrections, presented is a possible relation for correction of input size values based on the carried out laboratory and in-situ testings.

Analysis of copper and uranyl malates by potentiometry, polarimetry and spectrophotometry

Energy Technology Data Exchange (ETDEWEB)

Khalil, I; Petit-Ramel, M M; Chapelet-Barbier, C [Lyon-1 Univ., 69 (France)

1978-07-15

The stability and optical constants of the copper malates (CuH/sub 2/Mal)/sup +/, (CuHMal), (CuH/sub 2/Mal/sub 2/)/sup 2 -/, (CuMal)/sup -/, (Cu/sub 2/Mal/sub 2/)/sup 2 -/, and (CuHsub(-1)Mal)/sup 2 -/ have been fitted by a pit-mapping method, which also gives their confidence limits, from potentiometric, visible spectroscopic and polarimetric measurements.

The Effect of Phosphate on the Morphological and Spectroscopic Properties of Copper Pipes Experiencing Localized Corrosion

Science.gov (United States)

Extensive localized or pitting corrosion of copper pipes used in household drinking-water plumbing can eventually lead to pinhole water leaks that may result in water damage, mold growth, and costly repairs. A growing number of problems have been associated with high pH and low ...

EIS pitting temperature determination of A182 nickel based alloy in simulated BWR environment containing dilute seawater

International Nuclear Information System (INIS)

Lavigne, Olivier; Shoji, Tetsuo; Takeda, Yoichi

2014-01-01

Graphical abstract: - Highlights: • Stable pitting events in function of the temperature are monitored by electrochemical impedance spectroscopy. • The pitting temperature for the nickel based alloy A182 in solution containing 450 ppm Cl − is defined as above 160 °C. • The presented method can be applied for others passive alloys as stainless steel in solution containing aggressive anions. - Abstract: A method based on electrochemical impedance spectroscopy (EIS) measurements to monitor the pitting temperature of passive alloys in a given media is developed in this communication. The pitting corrosion behavior of the nickel based alloy 182 in water containing 450 ppm by weight of chloride is presented in this study. The analysis of the EIS fit parameters from the proposed equivalent electrical circuit allows to determine the temperature from which stable pitting event occurs at open circuit potential. For the A182 sample this temperature is measured above 160 °C

Musculoskeletal symptoms and exposure to whole-body vibration among open-pit mine workers in the Arctic.

Science.gov (United States)

Burström, Lage; Aminoff, Anna; Björ, Bodil; Mänttäri, Satu; Nilsson, Tohr; Pettersson, Hans; Rintamäki, Hannu; Rödin, Ingemar; Shilov, Victor; Talykova, Ljudmila; Vaktskjold, Arild; Wahlström, Jens

2017-06-19

This cross-sectional questionnaire study was carried out at 4 open-pit mines in Finland, Norway, Russia and Sweden as part of the MineHealth project. The aim has been to compare the prevalence of musculoskeletal symptoms between drivers of mining vehicles and non-drivers. The mine workers were asked whether they had suffered from any musculoskeletal symptoms during the previous 12 months in specified body regions, and to grade the severity of these symptoms during the past month. They were also asked about their daily driving of mining vehicles. The questionnaire was completed by 1323 workers (757 vehicle drivers) and the reported prevalence and severity of symptoms were highest for the lower back, followed by pain in the neck, shoulder and upper back. Drivers in the Nordic mines reported fewer symptoms than non-drivers, while for Russian mine workers the results were the opposite of that. The daily driving of mining vehicles had no significant association with the risk of symptoms. Female drivers indicated a higher prevalence of symptoms as compared to male drivers. The study provided only weak support for the hypothesis that drivers of vehicles reported a higher prevalence of musculoskeletal symptoms than non-vehicle drivers. There were marked differences in the prevalence of symptoms among workers in various enterprises, even though the nature of the job tasks was similar. Int J Occup Med Environ Health 2017;30(4):553-564. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Detection and Monitoring of Surface Motions in Active Open Pit Iron Mine in the Amazon Region, Using Persistent Scatterer Interferometry with TerraSAR-X Satellite Data

Directory of Open Access Journals (Sweden)

Marcos E. Hartwig

2013-09-01

Full Text Available Persistent Scatterer interferometry (PSI represents a powerful tool for the detection and monitoring of tiny surface deformations in vast areas, allowing a better understanding of its triggering mechanisms, planning of mitigation measures, as well as to find better solutions for social and environmental issues. However, there is no record hitherto of its use in active open pit mine in tropical rainforest environment. In this paper we evaluate the use of the PSI technique for the detection and monitoring of mine slope deformations in the N4W iron mine and its surroundings, Pará State, Northern Brazil. The PSI processing was performed with 18 ascending SAR scenes of the TerraSAR-X satellite acquired in the dry season of 2012. The results showed a significant number of widely distributed persistent scatterers. It was observed that most of the study area was stable during the time span. Nevertheless, high deformation rates (312 mm/year were mapped over the mine waste piles, but do not offer any hazard, since they are expected displacements of meters in magnitude for these manmade land structures. Additionally, it was mapped tiny deformation rates in both the east and west flanks of pits 1 and 2. The main underlying reasons can be assigned to the accommodation phenomena of very poor rock masses, to the local geometric variations of the slope cuts, to the geological contact between ironstones and the country rocks, to the exploitation activities, as well as to the major geological structures. This study showed the applicability of the PSI technique using TerraSAR-X scenes in active open pit mines in tropical moist environment. However, the PSI technique is not capable in providing real-time warnings, and faces limitations due to SAR viewing geometry. In this sense, we strongly recommend the use of radar scenes acquired in both ascending and descending orbits, which would also provide a more complete understanding of the deformation patterns.

MINE-NEC - A Game for the Analysis of Regional Water Policies in Open-Pit Lignite Mining Areas: An Improved Implementation for the NEC PC-8201A

OpenAIRE

Kaden, S.; Varis, O.

1986-01-01

The game MINE was developed for the analysis of regional water policies in open-pit lignite mining areas. It is implemented for a GDR test area. The purpose of the game is above all to teach decision makers and their staff in mining regions in order to get a better understanding of the complex interrelated socio-economic processes with respect t o water management in such regions. The game is designed to be played by five groups of players representing municipal and industrial water supply, a...

Assessing the effect of agricultural land abandonment on bird communities in southern-eastern Europe.

Science.gov (United States)

Zakkak, Sylvia; Radovic, Andreja; Nikolov, Stoyan C; Shumka, Spase; Kakalis, Lefteris; Kati, Vassiliki

2015-12-01

Agricultural land abandonment is recognized as a major environmental threat in Europe, being particularly pronounced in south-eastern Europe, where knowledge on its effects is limited. Taking the Balkan Peninsula as a case study, we investigated agricultural abandonment impact on passerine communities at regional level. We set up a standard methodology for site selection (70 sites) and data collection, along a well-defined forest-encroachment gradient that reflects land abandonment in four countries: Albania, Bulgaria, Croatia and Greece. Regardless the different socio-economic and political histories in the Balkans that led to diverse land abandonment patterns in space and time, rural abandonment had a consistent negative effect on bird communities, while regional-level analysis revealed patterns that were hidden at local level. The general trends were an increase of forest-dwelling bird species at the expense of farmland birds, the decline of overall bird species richness, as well as the decline of Species of European Conservation Concern (SPECs) richness and abundance. Many farmland bird species declined with land abandonment, whereas few forest species benefited from the process. In conclusion, our results support CAP towards hampering rural land abandonment and preserving semi-open rural mosaics in remote upland areas, using a suite of management measures carefully tailored to local needs. The maintenance of traditional rural landscapes should be prioritized in the Balkans, through the timely identification of HNV farmland that is most prone to abandonment. We also suggest that coordinated transnational research is needed, for a better assessment of conservation options in remote rural landscapes at European scale, including the enhancement of wild grazers' populations as an alternative in areas where traditional land management is rather unlikely to be re-established. Copyright © 2015 Elsevier Ltd. All rights reserved.

Consequences of coal mining and burning in the North Bohemian Brown Coal Basin (2). Territorial consequences of coal mining

International Nuclear Information System (INIS)

Stahlik, Z.

1992-01-01

Out of the 1450 km 2 of the North Bohemian Brown Coal Basin, the area of the coal-bearing territory is 850 km 2 . The area occupied by the open pits, spoil banks and mines is nearly 27O km 2 , out of which over 90 km 2 have already been recultivated. Predicted mining development scenarios for the region till 2035 are outlined. The extent of mining will decrease gradually, and land will be reclaimed. The abandoned pits will be filled with water and employed for recreation purposes. The specific features of the individual open pit mines are given. The ways to reduce the adverse environmental impacts of mining are outlined; these include, in particular, desulfurization of existing power plants on the one hand, and energy savings associated with a reduction in mining and power generation activities on the other hand. (J.B.)

Baseline Risk Assessment for the F-Area Burning/Rubble Pits and Rubble Pit

Energy Technology Data Exchange (ETDEWEB)

Palmer, E. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1996-03-01

This document provides an overview of the Savannah River Site (SRS) and a description of the F-Area Burning/Rubble Pits (BRPs) and Rubble Pit (RP) unit. It also describes the objectives and scope of the baseline risk assessment (BRA).

Tanacetum vulgare as a bioindicator of trace-metal contamination: a study of a naturally colonized open-pit lignite mine.

Science.gov (United States)

Jasion, Mateusz; Samecka-Cymerman, Aleksandra; Kolon, Krzysztof; Kempers, Alexander J

2013-10-01

We investigated the possibility of use of Tanacetum vulgare (tansy) as an ecological indicator of metal concentration in a naturally colonized open-pit lignite mine in Bełchatów (Poland). Tanacetum vulgare is the only species growing abundantly and spontaneously in the lignite mine waste dumps. Metal concentrations in roots, stems, leaves, flowers, and soil were measured in dump sites differing in type and time of reclamation and therefore differing in pollution levels. Tanacetum vulgare appeared to be an accumulator of chromium and iron in roots, whereas highest concentrations of manganese and zinc were found in leaves. A high bioaccumulation factor for cadmium (Cd) was observed in dumps and control sites, indicating that even small amounts of Cd in the environment may result in significant uptake by the plant. The lowest concentrations of metals were found in plants from sites situated on dumps reclaimed with argillaceous limestone.

Geotechnical approach for occupational safety risk analysis of critical slope in open pit mining as implication for earthquake hazard

Science.gov (United States)

Munirwansyah; Irsyam, Masyhur; Munirwan, Reza P.; Yunita, Halida; Zulfan Usrina, M.

2018-05-01

Occupational safety and health (OSH) is a planned effort to prevent accidents and diseases caused by work. In conducting mining activities often occur work accidents caused by unsafe field conditions. In open mine area, there is often a slump due to unstable slopes, which can disrupt the activities and productivity of mining companies. Based on research on stability of open pit slopes conducted by Febrianti [8], the Meureubo coal mine located in Aceh Barat district, on the slope of mine was indicated unsafe slope conditions, it will be continued research on OSH for landslide which is to understand the stability of the excavation slope and the shape of the slope collapse. Plaxis software was used for this research. After analyzing the slope stability and the effect of landslide on OSH with Job Safety Analysis (JSA) method, to identify the hazard to work safety, risk management analysis will be conducted to classified hazard level and its handling technique. This research aim is to know the level of risk of work accident at the company and its prevention effort. The result of risk analysis research is very high-risk value that is > 350 then the activity must be stopped until the risk can be reduced to reach the risk value limit < 20 which is allowed or accepted.

Corrosion of copper and authigenic sulfide mineral growth in hydrothermal bentonite experiments

Energy Technology Data Exchange (ETDEWEB)

Caporuscio, F.A., E-mail: floriec@lanl.gov [Los Alamos National Laboratory, Earth and Environmental Sciences, MS J966, Los Alamos, NM 87545 (United States); Palaich, S.E.M. [University of California, Los Angeles, CA 90095 (United States); Cheshire, M.C. [Los Alamos National Laboratory, Earth and Environmental Sciences, MS J966, Los Alamos, NM 87545 (United States); Jové Colón, C.F. [Sandia National Laboratory, Albuquerque, NM 87185 (United States)

2017-03-15

The focus of this experimental work is to characterize interaction of bentonite with possible used-fuel waste container materials. Experiments were performed up to 300 °C at 150–160 bars for five to six weeks. Bentonite was saturated with a 1900 ppm K-Ca-Na-Cl-bearing water with Cu-foils. Copper rapidly degrades into chalcocite (CuS{sub 2}) and minor covellite (CuS) in the presence of H{sub 2}S. Chalcocite growth and corrosion pit depths were measured for four different experimental runs yielding corrosion rates between 8.8 and 116 μm/yr depending on duration of experiment, brine composition, and clay type (bentonite vs. Opalinus Clay). Results of this research show that although pit-corrosion is demonstrated on Cu substrates, experiments show that the reactions that ensue, and the formation of minerals that develop, are extraordinarily slow. This supports the use of Cu in nuclide-containment systems as a possible engineered barrier system material. - Highlights: • Experiments run at 300 °C and 150 bars for up to six weeks. • Copper degrades to chalcocite (CuS2) and minor covellite (CuS) in presence of H2S. • Corrosion rates between 8.8 and 116 μm/yr. • Rate dependent on experiment duration, brine composition, and clay type. • Sulfide corrosion products may inhibit further corrosion of copper.

Distribution and chemical forms of copper in the root cells of castor seedlings and their tolerance to copper phytotoxicity in hydroponic culture.

Science.gov (United States)

Kang, Wei; Bao, Jianguo; Zheng, Jin; Hu, Hongqin; Du, Jiangkun

2015-05-01

The subcellular localization and chemical forms of copper in castor (Ricinus communis L.) seedlings grown in hydroponic nutrient solution were identified by chemical extraction, transmission electron microscopy, and Fourier transform infrared spectroscopy. The wild castor seeds were harvested from an abandoned copper mine in Tonglu Mountain, Daye City of Hubei Province, China. The results revealed that (1) the seedlings grew naturally in MS liquid medium with 40.00 mg kg(-1) CuSO4, in which the seedling growth rate and biomass index were 0.14 and 1.23, respectively, which were the highest values among all the treatments. The copper content in castor seedlings increased along with elevated CuSO4 concentration in the medium, reaching a maximum value of 16 570.12 mg kg(-1)(DW) when exposed to 60.00 mg L(-1) CuSO4, where 91.31% of the copper was accumulated in roots. (2) The copper existed in various chemical forms in the roots of the castor seedlings. Copper of 67.66% was extracted from the components of cell walls, such as exchangeable acidic polar compounds, cellulose and lignin, protein and pectin, and less concentrated in cell cytoplasm and nuclei. (3) Furthermore, the root cell walls were thickened when the castor seedlings exposed to CuSO4, with a large amount of high-density electron bodies, attached to the thickened cell walls. In the cell walls, most copper was bound to the carboxyl (-COOH) and hydroxyl (-OH) groups of acidic polar compounds, cellulose, hemicellulose, and polysaccharides. The conclusion showed that castor exhibited a strong tolerance to copper, the copper were accumulated mainly in the root cell, the root cell walls of castor were the major location of patience and detoxification in copper stress.

Corrosion of aluminium in copper-aluminium couples under a marine environment: Influence of polyaniline deposited onto copper

International Nuclear Information System (INIS)

Vera, Rosa; Verdugo, Patricia; Orellana, Marco; Munoz, Eduardo

2010-01-01

Research highlights: → The presence of Polyaniline in the Al-Cu system produces a decrease in the oxygen reduction reaction. → In the marine enviroment, aluminium in Al-Cu couples, suffers pitting and exfoliation. → The aluminium deterioration increases with chloride and enviromental sulphur dioxide presence, mainly when it is united to bare copper. - Abstract: In this study, we examined how aluminium corrosion in Al-Cu/PANI galvanic couples in a marine environment is influenced by deposition of polyaniline (PANI) on copper. Polarization curves and immersion assays in 0.1 M NaCl were performed. The morphologies of etched Al and corrosion products were observed by SEM, and the Al ions in solution were quantified by atomic absorption spectroscopy. A reduction in aluminium damage due to galvanic corrosion was observed as a result of decreased effective area for the oxygen reduction reaction on Cu/PANI electrode. Furthermore, an electrochemical reduction of PANI from leucoemeraldine to emeraldine base is proposed.

Burning/Rubble Pits: Environmental information document

International Nuclear Information System (INIS)

Huber, L.A.; Johnson, W.F.; Marine, I.W.

1987-03-01

The Burning/Rubble Pits, located near each of the major operating areas at the Savannah River Plant (SRP), began collecting burnable waste in 1951. The waste was incinerated monthly. All Burning/Rubble Pits are currently closed except for Burning/Rubble Pit 131-1R, which has not been backfilled but is inactive. No soil cores from the Burning/Rubble Pits have been analyzed. There are four groundwater monitoring wells located around each of the pits, which have been sampled quarterly since 1984. The closure options considered for the Burning/Rubble Pits are waste removal and closure, no waste removal and closure, and no action. Modeling calculations were made to determine the risks to human population for the three postulated closure options. An ecological assessment was conducted to predict the environmental impacts on aquatic and terrestrial biota. The relative costs for each of the closure options were estimated. An evaluation of the environmental impacts from the Burning/Rubble Pits indicates that the relative risks to human health and ecosystems for the postulated closure options are low. The ecological assessment shows that the effects of any closure activities on river water quality and wildlife would be insignificant. The cost estimates show the waste removal and closure option to be the most expensive for all of the pits. 38 refs., 35 figs., 47 tabs

THE EFFECT OF PHOSPHATE ON THE MORPHOLOGICAL AND SPECTROSCOPIC PROPERTIES OF COPPER DRINKING WATER PIPES EXPERIENCING LOCALIZED CORROSION

Science.gov (United States)

Extensive localized or pitting corrosion of copper pipes used in household drinking-water plumbing can eventually lead to pinhole water leaks that may result in water damage, mold growth, and costly repairs. A large water system in Florida has been addressing a widespread pinhole...

Advantages and limitations for users of double pit pour-flush latrines: a qualitative study in rural Bangladesh.

Science.gov (United States)

Hussain, Faruqe; Clasen, Thomas; Akter, Shahinoor; Bawel, Victoria; Luby, Stephen P; Leontsini, Elli; Unicomb, Leanne; Barua, Milan Kanti; Thomas, Brittany; Winch, Peter J

2017-05-25

In rural Bangladesh, India and elsewhere, pour-flush pit latrines are the most common sanitation system. When a single pit latrine becomes full, users must empty it themselves and risk exposure to fresh feces, pay an emptying service to remove pit contents or build a new latrine. Double pit pour-flush latrines may serve as a long-term sanitation option including high water table areas because the pits do not need to be emptied immediately and the excreta decomposes into reusable soil. Double pit pour-flush latrines were implemented in rural Bangladesh for 'hardcore poor' households by a national NGO, BRAC. We conducted interviews, focus groups, and spot checks in two low-income, rural areas of Bangladesh to explore the advantages and limitations of using double pit latrines compared to single pit latrines. The rural households accepted the double pit pour-flush latrine model and considered it feasible to use and maintain. This latrine design increased accessibility of a sanitation facility for these low-income residents and provided privacy, convenience and comfort, compared to open defecation. Although a double pit latrine is more costly and requires more space than a single pit latrine the households perceived this sanitation system to save resources, because households did not need to hire service workers to empty pits or remove decomposed contents themselves. In addition, the excreta decomposition process produced a reusable soil product that some households used in homestead gardening. The durability of the latrine superstructures was a problem, as most of the bamboo-pole superstructure broke after 6-18 months of use. Double pit pour-flush latrines are a long-term improved sanitation option that offers users several important advantages over single pit pour-flush latrines like in rural Bangladesh which can also be used in areas with high water table. Further research can provide an understanding of the comparative health impacts and effectiveness of the model

Advantages and limitations for users of double pit pour-flush latrines: a qualitative study in rural Bangladesh

Directory of Open Access Journals (Sweden)

Faruqe Hussain

2017-05-01

Full Text Available Abstract Background In rural Bangladesh, India and elsewhere, pour-flush pit latrines are the most common sanitation system. When a single pit latrine becomes full, users must empty it themselves and risk exposure to fresh feces, pay an emptying service to remove pit contents or build a new latrine. Double pit pour-flush latrines may serve as a long-term sanitation option including high water table areas because the pits do not need to be emptied immediately and the excreta decomposes into reusable soil. Methods Double pit pour-flush latrines were implemented in rural Bangladesh for ‘hardcore poor’ households by a national NGO, BRAC. We conducted interviews, focus groups, and spot checks in two low-income, rural areas of Bangladesh to explore the advantages and limitations of using double pit latrines compared to single pit latrines. Results The rural households accepted the double pit pour-flush latrine model and considered it feasible to use and maintain. This latrine design increased accessibility of a sanitation facility for these low-income residents and provided privacy, convenience and comfort, compared to open defecation. Although a double pit latrine is more costly and requires more space than a single pit latrine the households perceived this sanitation system to save resources, because households did not need to hire service workers to empty pits or remove decomposed contents themselves. In addition, the excreta decomposition process produced a reusable soil product that some households used in homestead gardening. The durability of the latrine superstructures was a problem, as most of the bamboo-pole superstructure broke after 6–18 months of use. Conclusions Double pit pour-flush latrines are a long-term improved sanitation option that offers users several important advantages over single pit pour-flush latrines like in rural Bangladesh which can also be used in areas with high water table. Further research can provide an

Care of the abandoned child.

Science.gov (United States)

Raghunath, M

1991-01-01

Care of abandoned children in India is discussed in terms of reasons for abandonment, the physical condition of the children, and legal categories. The options available currently are the cottage system, sponsorship programs, foster care, or adoption. Child-care and rehabilitation that may be necessary is specified as is the importance of maintaining records. The gaps in child-care are exposed. The role of nongovernmental organization (NGOs) and new legislation in closing the gaps is presented. Abandonment is usually a direct result of poverty, but it can also be caused by mental or physical handicaps or illegitimacy. The numbers of abandoned children may reach 2 million. 40-60% of abandoned infants die during monsoons and summers. The legal categories are privately abandoned, children on remand, or court-committed children. The cottage system emphasizes deinstitutionalization, but there remains a great demand for care. Sponsorship aims to strengthen the family unit to prevent abandonment. Foster care provides an alternative family substitute, but is known only theoretically. Childcare may involve instant hospitalization, care is an institution, or foster care with a suitable family. Nursery care requires discipline in hygiene, sanitation, maintenance of individual medical records, and a general cheerful atmosphere. Records are important for the child in later life and for adoption. Rehabilitation is a sociolegal process which must be done properly or it can jeopardize a child's future security. Despite the Supreme Court guidelines of 1984, there is no uniform system of adoption practices, and the child's interests are overlooked when adoptions are promoted. NGOs play an important role in making social welfare programs work. However their efforts are of limited help without government support and legislation. There is a lack of proper legislation which is outside the control of political and religious interests; e.g., Hindu law only permits adoption of one child of

Pitting corrosion of friction stir welded aluminum alloy thick plate in alkaline chloride solution

International Nuclear Information System (INIS)

Xu Weifeng; Liu Jinhe; Zhu Hongqiang

2010-01-01

The pitting corrosion of different positions (Top, Middle and Bottom) of weld nugget zone (WNZ) along thickness plate in friction stir welded 2219-O aluminum alloy in alkaline chloride solution was investigated by using open circuit potential, cyclic polarization, scanning electron microscopy and atomic force microscope. The results indicate that the material presents significant passivation, the top has highest corrosion potential, pitting potential and re-passivation potential compared with the bottom and base material. With the increase of traverse speed from 60 to 100 mm/min or rotary speed from 500 to 600 rpm, the corrosion resistance decreases.

Use of overburden rocks from open-pit coal mines and waste coals of Western Siberia for ceramic brick production with a defect-free structure

Science.gov (United States)

Stolboushkin, A. Yu; Ivanov, A. I.; Storozhenko, G. I.; Syromyasov, V. A.; Akst, D. V.

2017-09-01

The rational technology for the production of ceramic bricks with a defect-free structure from coal mining and processing wastes was developed. The results of comparison of physical and mechanical properties and the structure of ceramic bricks manufactured from overburden rocks and waste coal with traditional for semi-dry pressing mass preparation and according to the developed method are given. It was established that a homogeneous, defect-free brick texture obtained from overburden rocks of open-pit mines and waste coal improves the quality of ceramic wall materials produced by the method of compression molding by more than 1.5 times compared to the brick with a traditional mass preparation.

Parturition pit: the bony imprint of vaginal birth

International Nuclear Information System (INIS)

McArthur, Tatum A.; Meyer, Isuzu; Jackson, Bradford; Pitt, Michael J.; Larrison, Matthew C.

2016-01-01

To retrospectively evaluate for pits along the dorsum of the pubic body in females and compare the presence/absence of these pits to vaginal birth data. We retrospectively reviewed females with vaginal birth data who underwent pelvic CT. The presence of pits along the dorsum of the pubic body, pit grade (0 = not present; 1 = faintly imperceptible; 2 = present; 3 = prominent), and the presence of osteitis condensans ilii, preauricular sulcus, and sacroiliac joint vacuum phenomenon were assessed on imaging. Musculoskeletal radiologists who were blinded to the birth data evaluated the CTs. 48 males were also evaluated for the presence of pits. 482 female patients underwent CT pelvis and 171 were excluded due to lack of vaginal birth data. Of the 311 study patients, 262 had prior vaginal birth(s) and 194 had pits on CT. Only 7 of the 49 patients without prior vaginal birth had pits. There was a statistically significant association between vaginal birth and presence of pits (p < 0.0001). Patients with more prominent pits (grades 2/3) had a greater number of vaginal births. As vaginal deliveries increased, the odds of having parturition pits greatly increased, adjusting for age and race at CT (p < 0.0001). No males had pits. Our study indicates that parturition pits are associated with prior vaginal birth and should be considered a characteristic of the female pelvis. The lytic appearance of prominent pits on imaging can simulate disease and create a diagnostic dilemma for interpreting radiologists. (orig.)

Ocean abandonment of radioactive waste. 2

International Nuclear Information System (INIS)

Kouyama, Hiroaki

1994-01-01

Now, the nuclear powered submarines armed with ballistic missiles have become the main strength of navy. In Russia, eight nuclear powered icebreakers are operated. Mainly PWRs are used for these nuclear ships. The fuel exchange for nuclear powered submarines is carried out after the use for nearly ten years, therefore, the degree of enrichment of U-235 in fuel seems considerably high. So far, the sinking accidents of five nuclear powered submarines were reported. Former USSR began the ocean abandonment of radioactive waste in 1959, and continued it up to recent date. The northern sea area where the abandonment was carried out and the abandoned amount of radioactivity are shown. Also those in Far East sea area are shown. The management system for radioactive waste in Russia, the course after the abandonment of liquid waste in Japan Sea by Russian navy, the response of Japan regarding the ocean abandonment of radioactive waste and so on are described. (K.I.)

Influence of Pitting Corrosion on Fatigue and Corrosion Fatigue of Ship and Offshore Structures, Part II: Load - Pit - Crack Interaction

Directory of Open Access Journals (Sweden)

Jakubowski Marek

2015-09-01

Full Text Available In the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation rate and growth , whose presence has been questioned by some authors but accepted by most of them. Influence of roughness of pit walls on fatigue life of a plate suffering pit corrosion and presence of the so called „ non-damaging” pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction of pit-to-crack transition moment by two different ways, i.e. considering a pit a stress concentrator or an equivalent crack, has been analyzed. Also, influence of statistical distribution of depth of corrosion pits as well as anticorrosion protection on fatigue and corrosion fatigue has been described.

Study of the pitting effects during the pre-ignition plasma–propellant interaction process

International Nuclear Information System (INIS)

Hang, Yuhua; Li, Xingwen; Wu, Jian; Jia, Shenli; Zhao, Weiyu; Murphy, Anthony B

2016-01-01

The propellant ignition mechanism has become a central issue in the electrothermal chemical (ETC) launch technology, and the pre-ignition plasma–propellant interactions are critical in determining the ignition characteristics. In this work, both an open-air ablation test and an interrupted burning test are conducted for three different propellants. A fused silica window, which is transparent in all relevant wavelengths, is utilized to investigate the role of the plasma radiation. Surface pitting of the propellants after interaction with the plasma is analyzed using a scanning electron microscope (SEM). The effect of pits on the plasma ignition is then studied and a possible formation mechanism of pits is proposed. The input heat flux and the surface temperature of the propellants are obtained by solving a pre-ignition plasma–propellant interaction model. The results shed light on the pre-ignition plasma ignition mechanisms and will assist in the development of propellants for an ETC launcher. (paper)

pitting corrosion susceptibility pitting corrosion susceptibility of aisi

African Journals Online (AJOL)

eobe

2DEPARTMENT OF MECHANICAL ENGINEERING, UNIVERSITY OF BENIN, BENIN- CITY, EDO STATE, NIGERIA. E-mail addresses: ... fluids and aggressive chemicals. Pitting corrosion ... the kitchen, food manufacturing and dispensing and.

30 CFR 57.4011 - Abandoned electric circuits.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Abandoned electric circuits. 57.4011 Section 57.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... and Control § 57.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized...

30 CFR 77.215-4 - Refuse piles; abandonment.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Refuse piles; abandonment. 77.215-4 Section 77... MINES Surface Installations § 77.215-4 Refuse piles; abandonment. When a refuse pile is to be abandoned... refuse pile shall be abandoned in accordance with a plan submitted by the operator and approved by the...

XPS investigation of copper corrosion in hydro-carbonate electrolytes

Energy Technology Data Exchange (ETDEWEB)

Sieber, I.; Hildebrand, H.; Schmuki, P. [University Erlangen-Nuremberg, Martensstr.7, D-91058 Erlangen (Germany); Kaluzhina, S.A. [Voronezh State University, University Sq.1, 394006 Voronezh (Russian Federation)

2004-07-01

Problems of corrosion and effective methods of metal protection are still actual in the present days. Special interest is in copper material, which as basic component of heat exchanger constructions can corrode in contact with carbonate water. The intensity of the corrosion destruction depends on the carbon water concentration and thermal conditions in the system. The present paper provides new insights into the role of the HCO{sub 3}{sup -} - ions in the corrosion process of copper. Copper samples after anodic oxidation in 0.02 and 0.1 M NaHCO{sub 3} have been studied using XPS and SEM. The presence of carbonate compounds in the passive film in 0.1 M NaHCO{sub 3} was established by XPS analysis all over the surface. These compounds are responsible for the protective character of the passive film towards local destruction. In the 0.02 M NaHCO{sub 3} electrolyte carbonate compounds were not found at places of pit formation after multi-cycling of the sample. (authors)

THE MEASUREMENT OF SELECTED SOIL PARAMETERS OF FORMER OPEN PIT MINE WITH THE USE OF TRIAXIAL STRESS APPARATUS

Directory of Open Access Journals (Sweden)

Janusz P. KOGUT

Full Text Available Identification of geotechnical soil conditions often requires execution of laboratory tests, especially if you want to measure dynamic parameters of the soil. At present, the triaxial shear apparatus is widely applied in determination of the parameters of the soil. On the basis of the soil samples analysis, the examination results provide a wide range of data from basic performance parameters, e.g. internal friction angle and cohesion, to most complex ones like Young’s modulus permanent side effective stress of water samples. Furthermore, the Soil Structure Interaction Laboratory of Cracow University of Technology, has carried out the measurements of propagation of shear waves velocity with the use of bender elements tests. This work presents geotechnical conditions and the analysis of the results, which might be found useful to determine the transportation load parameters of designed S-7 and S-52 routes, as well as overall impact on soil/structure and surrounding areas located over the former clay open-pit mine. The landslides existing in the vicinity of the mine have prompted the authors to take that action.

Oxygen pitting failure of a bagasse boiler tube

CSIR Research Space (South Africa)

Heyes, AM

2001-04-01

Full Text Available Examination of a failed roof tube from a bagasse boiler showed transverse through-cracks and extensive pitting. The pitting was typically oxygen induced pitting and numerous fatigue cracks had started within these pits. It is highly probable...

Accountability Quality Shuffler Measurements on Pits

International Nuclear Information System (INIS)

Rinard, P.M.

2000-01-01

Pits have generally been treated as accountable units that are intact if merely present and they are excluded from the more demanding nondestructive assay requirements. As pits begin to flow into disposition streams, there may be more incentive to measure the masses of their fissile components for accountability purposes. This Department of Energy Office of Safeguards and Security (OSS) Lifecycle Project has explored some ways in which such measurements may be done successfully. The active neutron instrument called a shuffler has been used to measure a variety of actual pits, and a calculational technique has been developed to accurately predict such count rates. Passive multiplicity counting has previously been applied to pits for determining their plutonium contents. This combination of measurement and calculational techniques provide powerful and accurate tools for determining the fissile contents of pits with the quality needed for accountability purposes

DEVELOPMENT OF A REPRODUCIBLE SCREENING METHOD TO DETERMINE THE MECHANISM AND EFFECT OF ORGANIC ACIDS AND OTHER CONTAMINANTS ON THE CORROSION OF ALUMINUM-FINNED COPPER-TUBE HEAT EXCHANGE COILS

Energy Technology Data Exchange (ETDEWEB)

Richard A. Corbett; Dave Severance

2005-02-01

Formicary corrosion is an insidious form of localized pitting corrosion. Notoya (1997b) wrote, ?In Japan, this type of corrosion is found in approximately 10% of cases of premature failure of copper tubes.? Attack characteristically features very small surface pits which are not visible to the un-aided eye, and random directional changes in the underlying copper metal. Attack is rapid. Failures have occurred before installation, shortly thereafter, or within several years later. Objectives of this Research Project Conduct an in depth literature search on the subject of formicary corrosion. Define the corrosion mechanism. Develop a test method that will reproduce formicary corrosion. Develop a test method for screening candidate materials that could cause formicary corrosion.

Decontamination of abandoned sites. An introduction into the problems of land decontamination

International Nuclear Information System (INIS)

Kundt, K.

1991-01-01

Starting from a brief overview of the history of origin of soil and ground water pollution in Berlin and its surroundings by gas, chemical, and petroleum works, old landfills, manufactories of arms and ammunition as well as gasoline depots or sites of gasoline depots, the brochure describes the legal situation and procedure (list of 'intervention' values) and goes on to outline the situation regarding the ground under Berlin, existing pollutants, and methods for dealing with land contamination. In five abandoned sites (waste oil refinery, copper refinery, waste solvent treatment plant, asphalt factory and drugs factory), different methods for eliminating soil and ground water contamination were used. Their efficacy is assessed on the basis of their soil and pollutant-specific suitability; the decontamination achieved is indicated. (BBR) [de

Using radon-222 for tracing groundwater discharge into an open-pit lignite mining lake--a case study.

Science.gov (United States)

Schmidt, Axel; Schubert, Michael

2007-12-01

Groundwater discharge into an open pit lignite mining lake was investigated using radon-222 as a naturally occurring environmental tracer. The chosen study site was a meromictic lake, i.e., a water body that is divided horizontally into two separate layers--the upper mixolimnion (with seasonal mixing) and the lower monimolimnion (without seasonal mixing). For the estimation of groundwater discharge rates into the lake, a simple box model including all radon sinks and sources related to each layer was applied. Two field investigations were performed. During the October campaign, the total groundwater discharge into the lake was found to be 18.9 and 0.7 m(3) d(-1) for the mixolimnion and monimolimnion, respectively. During the December campaign, the groundwater discharge into the mixolimnion was 15.0 m(3) d(-1), whereas no discharge at all was observed into the monimolimnion. Based on the given water volumes, the residence time of lake water was 5.3 years for the monimolimnion and varies between 0.9 and 1.1 years for the mixolimnion. The investigation confirmed radon to be a useful environmental tracer for groundwater and surface water interactions in meromictic lake environments.

Environmental geochemistry of abandoned flotation tailing reservior from the Tonglvshan Fe-Cu sulfide mine in Daye, Central China.

Science.gov (United States)

Guo, Y; Bao, Z Y; Deng, Y M; Ma, Z Z; Yan, S

2011-07-01

This study investigated metals of tailings from Tonglvshan mine in Daye and assessed the effect of metal contamination in water and sediment near the tailing reservoir. The concentration of copper, lead, zinc, cadmium, chromium and nickel was measured in deposit samples taken from a profile in an abandoned flotation tailing reservoir, as well as in water and sediment samples near the reservoir. The results of this study indicate that copper concentration ranges from 780 to 4390 mg/kg, 2-10 times higher than the limit values in soil, while the contents of other metals are below the limit values. Metal levels in water and sediments are high and varied widely in different sampling sites. The mean concentrations of copper, lead, zinc, cadmium, chromium and nickel in waters are 27.76, 2.28, 8.20, 0.12, 5.30 and 3.04 mg/L, while those in sediments are 557.65, 96.95, 285.20, 0.92, 94.30 and 4.75 mg/kg, respectively. All of the results indicate that the environment near the tailing reservoir is polluted to some extent by some kinds of metals, especially by copper, lead, zinc and cadmium, which may be caused not only by some discharge sources of metals, but also by life garbage and sewage.

Surface films and corrosion of copper

International Nuclear Information System (INIS)

Hilden, J.; Laitinen, T.; Maekelae, K.; Saario, T.; Bojinov, M.

1999-03-01

In Sweden and Finland the spent nuclear fuel is planned to be encapsulated in cast iron canisters that have an outer shield made of copper. The copper shield is responsible for the corrosion protection of the canister construction. General corrosion of the copper is not expected to be the limiting factor in the waste repository environment when estimating the life-time of the canister construction. However, different forms of localised corrosion, i.e. pitting, stress corrosion cracking, or environmentally assisted creep fracture may cause premature failure of the copper shield. Of the probable constituents in the groundwater, nitrites, chlorides, sulphides and carbonates have been suggested to promote localised corrosion of copper. The main assumption made in planning this research program is that the surface films forming on copper in the repository environment largely determine the susceptibility of copper to the different forms of localised corrosion. The availability of reactants, which also may become corrosion rate limiting, is investigated in several other research programs. This research program consists of a set of successive projects targeted at characterising the properties of surface films on copper in repository environment containing different detrimental anions. A further aim was to assess the significance of the anion-induced changes in the stability of the oxide films with regard to localised corrosion of copper. This report summarises the results from a series of investigations on properties of surface films forming on copper in water of pH = 8.9 at temperature of 80 deg C and pressure of 2 MPa. The main results gained so far in this research program are as follows: The surface films forming on copper in the thermodynamic stability region of monovalent copper at 80 deg C consist of a bulk part (about 1 mm thick) which is a good ionic and electronic conductor, and an outer, interfacial layer (0.001 - 0.005 mm thick) which shows p-type semiconductor

Microstructure of the optic disc pit in open-angle glaucoma.

Science.gov (United States)

Choi, Yun Jeong; Lee, Eun Ji; Kim, Bo Hyuk; Kim, Tae-Woo

2014-11-01

To investigate the structural and clinical characteristics of the optic disc pit (ODP) in primary open-angle glaucoma (POAG) via enhanced depth imaging (EDI) spectral-domain optical coherence tomography (SD-OCT). Prospective, observational case series. Seventy POAG eyes clinically diagnosed with an ODP via stereo disc photography. Optic discs were scanned using EDI SD-OCT. Serial horizontal and vertical B-scan images covering the optic discs were obtained from each eye. The structural characteristics of the ODP were investigated via 3-dimensional images constructed from the serial B-scans, focusing on the presence of alterations in the contour of the lamina cribrosa (LC) or prelaminar tissue (PLT), in conjunction with associated clinical characteristics. The structural characteristics of the ODP and associated clinical characteristics. In the EDI SD-OCT images, the ODP was viewed as an isolated alteration of the LC (n = 14, 20.0%) or PLT (n = 16, 22.9%) or an alteration of both the LC and PLT (n = 40, 57.1%). Alterations of the LC were located at the mid-periphery near the LC insertion (n = 17) or far periphery adjacent to the LC insertion (n = 37), and the depth of alteration was deep (n = 23), involving nearly full-thickness LC, or shallow (n = 31), with partially visible LC at the base. Fifty-four eyes (77.1%) exhibited parafoveal visual field (VF) defect within 10 degrees of fixation, and in 98.1% of these eyes (53/54) it was spatially associated with the location of ODP. The parafoveal VF defect was more prevalent in eyes with LC alteration than those without (83.3% vs. 56.2%, P = 0.023) and in eyes with deep LC defect than those with shallow defect (95.7% vs. 74.2%, P = 0.036). Disc hemorrhage (32.4% vs. 0.0%, P = 0.008) and peripapillary retinoschisis (18.9 vs. 0.0%, P = 0.055) were more strongly associated with LC alterations located at the far periphery than at the mid-periphery. Enhanced depth imaging SD-OCT facilitated visualization of the varied

Requalification of Abandoned Tunnels

Directory of Open Access Journals (Sweden)

Gianluca Derosa

2014-12-01

Full Text Available In a vision of regeneration of the abandoned highway stretch close to Vado (Bologna, the galleries, theme of the project, are planned to be part of a footpath network, since the position of the galleries make them reachable both from the small town of Vado and from the new highway. The project’s aim is to offer a space to the community, hence the considered functions are thought as useful both for inhabitants and for tourists. Three galleries, three different characteristics, three different destinations and uses: The first gallery, with only one entrance, is planned to be the identity of the system. The second gallery is a more flexible space, where many functions take place. The third galleryis thought as a fast link to the naturalistic path for who’s arriving from the highway. This flexible wooden structure also creates an entrance and open space out of the galleries giving continuity to the project.

Demonstration of In-Situ Stabilization of Buried Waste at Pit G-11 at the Brookhaven National laboratory Glass Pits Disposal Site

International Nuclear Information System (INIS)

Dwyer, B.P.; Gilbert, J.; Heiser, J.

1999-01-01

In 1989 BNL was added to the EPAs National Priorities List. The site is divided into seven operable units (OU). OU-I includes the former landfill area. The field task site is noted as the AOC 2C Glass Holes location. Beginning in the 1960s and continuing into the 1980s, BNL disposed of laboratory waste (glassware, chemicals and animal carcasses) in numerous shallow pits. The drivers for remediating the pits are; historical records that indicate hazardous materials may have been disposed of in the pits; ground water contamination down gradient of the pits; a test excavation of one of the glass holes that unearthed laboratory glass bottles with unidentified liquids still contained; and the fact that BNL rests atop an EPA designated sole-source aquifer. The specific site chosen for this demonstration was pit G-11. The requirements that lead to choosing this pit were; a well characterized pit and a relatively isolated pit where our construction operations would not impact on adjacent pits. The glass holes area, including pit G-11, was comprehensively surveyed using a suite of geophysical techniques (e.g., EM-31, EM-61, GPR). Prior to stabilizing the waste form a subsurface barrier was constructed to contain the entire waste pit. The pit contents were then stabilized using a cement grout applied via jet grouting. The stabilization was performed to make removal of the waste from the pit easier and safer in terms of worker exposure. The grouting process would mix and masticate the waste and grout and form a single monolithic waste form. This large monolith would then be subdivided into smaller 4 foot by 4 foot by 10-12 foot block using a demolition grout. The smaller blocks would then be easily removed from the site and disposed of in a CERCLA waste site

Experimental Stress Analysis at Railway Inspection Pit

Directory of Open Access Journals (Sweden)

Nicuşor Laurentiu Zaharia

2008-10-01

Full Text Available Railway inspection pits are used in railway halls. The purpose of inspection pits is to allow the working under the vehicle. Inspection pits can be found in locomotive depots, factories etc. The new design for a inspection pit in a railway hall involve tests in purpose of homologations the railway infrastructure. Before the homologation committee meeting, tests are made; after the test, a testing report is made which it will be part at homologation documents.

Geochemical evolution of a high arsenic, alkaline pit-lake in the Mother Lode Gold District, California

Science.gov (United States)

Savage, Kaye S.; Ashley, Roger P.; Bird, Dennis K.

2009-01-01

The Harvard orebody at the Jamestown gold mine, located along the Melones fault zone in the southern Mother Lode gold district, California, was mined in an open-pit operation from 1987 to 1994. Dewatering during mining produced a hydrologic cone of depression; recovery toward the premining ground-water configuration produced a monomictic pit lake with alkaline Ca-Mg-HCO3-SO4–type pit water, concentrations of As up to 1,200 μg/L, and total dissolved solids (TDS) up to 2,000 mg/L. In this study, pit-wall rocks were mapped and chemically analyzed to provide a context for evaluating observed variability in the composition of the pit-lake waters in relationship to seasonal weather patterns. An integrated hydrogeochemical model of pit-lake evolution based on observations of pit-lake volume, water composition (samples collected between 1998–2000, 2004), and processes occurring on pit walls was developed in three stages using the computer code PHREEQC. Stage 1 takes account of seasonally variable water fluxes from precipitation, evaporation, springs, and ground water, as well as lake stratification and mixing processes. Stage 2 adds CO2fluxes and wall-rock interactions, and stage 3 assesses the predictive capability of the model.Two major geologic units in fault contact comprise the pit walls. The hanging wall is composed of interlayered slate, metavolcanic and metavolcaniclastic rocks, and schists; the footwall rocks are chlorite-actinolite and talc-tremolite schists generated by metasomatism of greenschist-facies mafic and ultramafic igneous rocks. Alteration in the ore zone provides evidence for mineralizing fluids that introduced CO2, S, and K2O, and redistributed SiO2. Arsenian pyrite associated with the alteration weathers to produce goethite and jarosite on pit walls and in joints, as well as copiapite and hexahydrite efflorescences that accumulate on wall-rock faces during dry California summers. All of these pyrite weathering products incorporate arsenic at

Pits on Ascraeus

Science.gov (United States)

2005-01-01

24 September 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows collapse pits and troughs on the lower northeast flank of the giant martian volcano, Ascraeus Mons. Layers of volcanic rock are evident in some of the pit and valley walls, and boulders the size of houses and trucks that were liberated from these walls by gravity can be seen on the floors of the depressions. Location near: 13.6oN, 102.6oW Image width: width: 3 km (1.9 mi) Illumination from: lower left Season: Northern Autumn

Impact of chlorinated disinfection on copper corrosion in hot water systems

Energy Technology Data Exchange (ETDEWEB)

Montes, J. Castillo [Centre Scientifique et Technique du Bâtiment Nantes, 11 rue Henri Picherit, BP 82341, 44323 Nantes Cedex 03 (France); Laboratoire des Sciences de l’Ingénieur pour l’Environnement, UMR-CNRS 7356, Université de La Rochelle, Avenue Michel Crépeau, 17042 La Rochelle Cedex 1 (France); Hamdani, F. [Laboratoire des Sciences de l’Ingénieur pour l’Environnement, UMR-CNRS 7356, Université de La Rochelle, Avenue Michel Crépeau, 17042 La Rochelle Cedex 1 (France); Creus, J., E-mail: jcreus@univ-lr.fr [Laboratoire des Sciences de l’Ingénieur pour l’Environnement, UMR-CNRS 7356, Université de La Rochelle, Avenue Michel Crépeau, 17042 La Rochelle Cedex 1 (France); Touzain, S. [Laboratoire des Sciences de l’Ingénieur pour l’Environnement, UMR-CNRS 7356, Université de La Rochelle, Avenue Michel Crépeau, 17042 La Rochelle Cedex 1 (France); Correc, O. [Centre Scientifique et Technique du Bâtiment Nantes, 11 rue Henri Picherit, BP 82341, 44323 Nantes Cedex 03 (France)

2014-09-30

Highlights: • Impact of disinfectant treatment on the durability of copper pipes. • Synergy between disinfectant concentration and temperature. • Pitting corrosion of copper associated to the corrosion products formation on copper. - Abstract: In France, hot water quality control inside buildings is occasionally ensured by disinfection treatments using temperature increases or addition of sodium hypochlorite (between 0.5 ppm and 1 ppm residual free chlorine). This disinfectant is a strong oxidiser and it could interact with metallic pipes usually used in hot water systems. This work deals with the study of the impact of these treatments on the durability of copper pipes. The objective of this work was to investigate the influence of sodium hypochlorite concentration and temperature on the copper corrosion mechanism. Copper samples were tested under dynamic and static conditions of ageing with sodium hypochlorite solutions ranging from 0 to 100 ppm with temperature at 50 °C and 70 °C. The efficiency of a corrosion inhibitor was investigated in dynamic conditions. Visual observations and analytical analyses of the internal surface of samples was studied at different ageing duration. Corrosion products were characterised by X-ray diffraction and Raman spectroscopy. Temperature and disinfectant were found to considerably affect the copper corrosion mechanism. Surprisingly, the corrosiveness of the solution was higher at lower temperatures. The temperature influences the nature of corrosion products. The protection efficiency is then strongly depend on the nature of the corrosion products formed at the surface of copper samples exposed to the aggressive solutions containing different concentration of disinfectant.

Corrosion of copper-based materials in gamma radiation

International Nuclear Information System (INIS)

Yunker, W.H.

1986-06-01

The corrosion behaviors of pure copper (CDA 101), 7% aluminum-copper bronze (CDA 613) and 30% nickel-copper (CDA 715) are being studied in a gamma radiation field of 1 x 10 5 R/h. These studies are in support of the Nevada Nuclear Waste Storage Investigations (NNWSI) Project, by Lawrence Livermore National Laboratory (LLNL), of copper-based materials for possible use in container systems for the permanent geologic burial of nuclear waste. Weight loss, tear drop (stressed), and crevice specimens of the three materials were exposed to water vapor-air atmospheres at 95 0 C and 150 0 C and to liquid water at 95 0 C for periods of one, three, and six months. Longer exposures are in progress. Measurements include: changes in the chemical composition of the gas and water, specimen weight changes, oxide film weights, evidence of microcracking and crevice corrosion, and chemical composition of the oxide films by Auger electron spectroscopy and x-ray diffraction. Interim results show considerable pit and under-film corrosion of alloys CDA 613 and CDA 715. Uniform corrosion rates range from 0.012 mil/yr (0.30 μm/yr) to 0.22 mil/yr (5.6 μm/yr), based on specimen weight losses during six- and seven-month exposures. The time dependencies will be determined as more data become available

A WebGIS Decision Support System for Management of Abandoned Mines

Directory of Open Access Journals (Sweden)

Ranka Stanković

2016-07-01

Full Text Available This paper presents the development of a WebGIS application aimed at providing safe and reliable data needed for reclamation of abandoned mines in national parks and other protected areas in Vojvodina in compliance with existing legal regulations. The geodatabase model for this application has been developed using UML and the CASE tool Microsoft Visio featuring an interface with ArcGIS. The WebGIS application was developed using GeoServer, an open source tool in the Java programming language, with integrated PostgreSQL DB and the possibility of generating and publishing WMS, WFS and KML services. The WebGIS application is publicly available, based on an appropriate central database, which for the first time encompasses all available data on abandoned mines in Vojvodina, and as such may serve as a model for similar databases on the territory of the Republic of Serbia.

How copper catalyzes the electroreduction of carbon dioxide into hydrocarbon fuels

DEFF Research Database (Denmark)

Peterson, Andrew; Abild-Pedersen, Frank; Studt, Felix

2010-01-01

Density functional theory calculations explain copper's unique ability to convert CO2 into hydrocarbons, which may open up (photo-)electrochemical routes to fuels.......Density functional theory calculations explain copper's unique ability to convert CO2 into hydrocarbons, which may open up (photo-)electrochemical routes to fuels....

The rail abandonment process: A southern perspective

International Nuclear Information System (INIS)

1988-12-01

One factor in evaluating the desirability of rail transport for high-level radioactive wastes or spent fuels is the frequency, or lack thereof, with which railroad and railroad lines have been, and are, abandoned. If DOE makes a decision to use the rail option and a line is subsequently abandoned, the choice results in increased cost, time delays and possibly safety problems: Information is therefore needed prior to the decision-making process to evaluate the desirability of the rail shipping option. One result of the abandonments mentioned herein, as well as other later abandonments, is the creation of a US rail system undergoing an evolutionary process in the 1980s as far-reaching as the changes that occurred when the industry was in its infancy a century and-a-half ago. The purpose of this paper is to examine the factors leading to some of these changes by tracing the historical development of the rail abandonment process, with particular emphasis on the rise of regional railroads, their problems in the modern era and current trends in rail abandonments as well as their effects on the southeastern United States

Dating of Las Mesas Copper Age walled enclosure (La Fuente, Spain

Directory of Open Access Journals (Sweden)

Odriozola, Carlos P.

2014-12-01

Full Text Available The site of Las Mesas is located in the west bank of the Guadajira river (La Fuente, Badajoz, Spain. It covers a half hectare and is enclosed by a stone wall. Previous assessments based on site surveys suggested a general chronological span from Late Neolithic period (ca. 3600-2900 BC through the Copper Age (3rd millennium BC. Excavations revealed a well-constructed wall with bastions and a domestic space at the centre of the site with three occupational phases. Several functional areas and a votive pit are ascribed to the second phase. A deer antler located in a re-cut ritual pit associated to the second phase was dated by AMS-14C. Samples from a living floor assigned to the second phase (SU-9/10 and the basement of a kiln associated with the first phase (SU-18 was dated by optically stimulated luminescence (OSL using the single aliquot regenerative dose (SAR protocol on 90-160 m quartz grains. Luminescence profiling analysis of 7 samples taken throughout the archaeological stratigraphy was used to assess variations in luminescence behaviour and relative age through the sequence, using infrared-, optically –and thermally– stimulated luminescence (IRSL, OSL, TSL on poly-mineral and etched samples. Luminescence dating and profiling indicates that the upper archaeological layer (SU-1B probably dates to the Late Bronze Age (ca. 1000 BC, but that the sediments in the remainder of this section accumulated during the late Neolithic-Copper Age: the site was most probably inhabited between 3300 and 2900 BC. There were gaps in occupation between the Late Neolithic-Cooper Age phases (I & II, and between the Late Neolithic-Cooper Age phases and Late Bronze Age phase (II & III, indicating that the site was abandoned and reoccupied twice. The AMS-14C date on deer antler of 4254 ± 45 BP (3010-2675 cal BC is consisten with the OSL results for phase II, indicating that the pit was excavated at the beginning of the second occupational phase. Combined OSL

Copper removal from contaminated soils by soil washing process using camellian-derived saponin

Science.gov (United States)

Reyes, Arturo; Fernanda Campos, Maria; Videla, Álvaro; Letelier, María Victoria; Fuentes, Bárbara

2015-04-01

Antofagasta Region in North of Chile has been the main copper producer district in the world. As a consequence of a lack of mining closure regulation, a large number of abandon small-to-medium size metal-contaminated sites have been identified in the last survey performed by the Chilean Government. Therefore, more research development on sustainable reclamation technologies must be made in this extreme arid-dry zone. The objective of this study is to test the effectiveness of soil remediation by washing contaminated soil using camellian-derived saponin for the mobilization of copper. Soil samples were taken from an abandoned copper mine site located at 30 km North Antofagasta city. They were dried and sieved at 75 µm for physico-chemical characterization. A commercial saponin extracted from camellias seed was used as biosurfactant. The soil used contains 67.4 % sand, 26.3 % silt and 6.3 % clay. The soil is highly saline (electric conductivity, 61 mScm-1), with low organic matter content (0.41%), with pH 7.30, and a high copper concentration (2200 mg Kg-1 soil). According to the sequential extraction procedure of the whole soil, copper species are mainly as exchangeable fraction (608.2 mg Kg-1 soil) and reducible fraction (787.3 mg Kg-1 soil), whereas the oxidizable and residual fractions are around 205.7 and 598.8 mg Kg-1 soil, respectively. Soil particles under 75 µm contain higher copper concentrations (1242 mg Kg-1 soil) than the particle fraction over 75 µm (912 mg Kg-1 soil). All washing assays were conducted in triplicate using a standard batch technique with and without pH adjustment. The testing protocols includes evaluation of four solid to liquid ratio (0.5:50; 1.0:50; 2.0:50, and 5.0:50) and three saponin concentrations (0, 1, and 4 mg L-1). After shaking (24 h, 20±1 °C) and subsequently filtration (0.45 µm), the supernatants were analyzed for copper and pH. The removal efficiencies of copper by saponin solutions were calculated in according to the

Air quality impact assessment of multiple open pit coal mines in northern Colombia.

Science.gov (United States)

Huertas, José I; Huertas, María E; Izquierdo, Sebastián; González, Enrique D

2012-01-01

The coal mining region in northern Colombia is one of the largest open pit mining regions of the world. In 2009, there were 8 mining companies in operation with an approximate coal production of ∼70 Mtons/year. Since 2007, the Colombian air quality monitoring network has reported readings that exceed the daily and annual air quality standards for total suspended particulate (TSP) matter and particles with an equivalent aerodynamic diameter smaller than 10 μm (PM₁₀) in nearby villages. This paper describes work carried out in order to establish an appropriate clean air program for this region, based on the Colombian national environmental authority requirement for modeling of TSP and PM(10) dispersion. A TSP and PM₁₀ emission inventory was initially developed, and topographic and meteorological information for the region was collected and analyzed. Using this information, the dispersion of TSP was modeled in ISC3 and AERMOD using meteorological data collected by 3 local stations during 2008 and 2009. The results obtained were compared to actual values measured by the air quality monitoring network. High correlation coefficients (>0.73) were obtained, indicating that the models accurately described the main factors affecting particle dispersion in the region. The model was then used to forecast concentrations of particulate matter for 2010. Based on results from the model, areas within the modeling region were identified as highly, fairly, moderately and marginally polluted according to local regulations. Additionally, the contribution particulate matter to the pollution at each village was estimated. Using these predicted values, the Colombian environmental authority imposed new decontamination measures on the mining companies operating in the region. These measures included the relocation of three villages financed by the mine companies based on forecasted pollution levels. Copyright © 2011. Published by Elsevier Ltd.

Effects of pH and chloride concentration on pitting corrosion of AA6061 aluminum alloy

International Nuclear Information System (INIS)

Zaid, B.; Saidi, D.; Benzaid, A.; Hadji, S.

2008-01-01

Effects of pH solution and chloride (Cl - ) ion concentration on the corrosion behaviour of alloy AA6061 immersed in aqueous solutions of NaCl have been investigated using measurements of weight loss, potentiodynamic polarisation, linear polarisation, cyclic polarisation experiment combined with open circuit potential transient technique and optical or scanning electron microscopy. The corrosion behaviour of the AA6061 aluminum alloy was found to be dependant on the pH and chloride concentration [NaCl] of solution. In acidic or slightly neutral solutions, general and pitting corrosion occurred simultaneously. In contrast, exposure to alkaline solutions results in general corrosion. Experience revealed that the alloy AA6061 was susceptible to pitting corrosion in all chloride solution of concentration ranging between 0.003 wt% and 5.5 wt% NaCl and an increase in the chloride concentration slightly shifted both the pitting E pit and corrosion E cor potentials to more active values. In function of the conditions of treatment, the sheets of the alloy AA6061 undergo two types of localised corrosion process, leading to the formation of hemispherical and crystallographic pits. Polarisation resistance measurements in acidic (pH = 2) and alkaline chloride solutions (pH = 12) which are in good agreement with those of weight loss, show that the corrosion kinetic is minimised in slightly neutral solutions (pH = 6)

Transformation on Abandonment

DEFF Research Database (Denmark)

Krag, Mo Michelsen Stochholm

2016-01-01

This paper outlines a research project on the increasing quantity of abandoned houses in the depopulating rural villages, and it reports on how an attempt is made to establish a counter-practice of radical preservation based on a series of full-scale transformations of abandoned buildings. The aim...... of the transformations is to reveal and preserve material and immaterial values such as aspects of cultural heritage, local narratives, and building density. The responses of local people are used as a feedback mechanism and considered an important impact indicator. Eleven transformations of varying strategies have...... houses. Transformation prototypes are tested as present manifestations in rural villages as an alternative way to preserve buildings as well as memories....

The Influence of Radiation on Pit Solution Chemistry as it Pertains to the Transition from Metastable to Stable Pitting in Steels

International Nuclear Information System (INIS)

Galuszka-Muga, Barbara; Muga, Luis M.

2006-01-01

Previous work relevant to current efforts is summarized. A description of an improved version of a new electrochemical probe, the ArtPit, is given. The distinct feature of the probe for investigating metastable pitting of carbon steels is specified and compared to other approaches. The electrochemical response of the ArtPit under the gamma irradiation and elevated temperature conditions that occur at high level waste (HLW) storage tanks is presented. In particular, the Tafel slope determinations and chemical analyses of the ArtPit confined volume electrolyte are described. Based on results a possible approach for reducing the corrosion rate of HLW tank walls is suggested. Additional statistical analysis of the occurrence of short duration (passivated pits) and long term (stable pitting) electrochemical pulses (current surges) during exposure confirm that radiation enhances the occurrence of both more and smaller sized pits due to increased likelihood of repassivation

Trade-offs of European agricultural abandonment

NARCIS (Netherlands)

van der Zanden, Emma H.; Verburg, Peter H.; Schulp, Catharina J E; Verkerk, Pieter Johannes

2017-01-01

Agricultural land abandonment is a policy challenge, especially for areas with unfavorable conditions for agriculture and remote and mountainous areas. Agricultural abandonment is an important land use process in many world regions and one of the dominant land use change processes in Europe.

PITTING CORROSION IN EROSIVE CONDITION OF AGED 550°C CU10NI-3AL-1,3FE ALLOY IN 0,01 M NA2 SO4

Directory of Open Access Journals (Sweden)

Rodrigo Nascimento Liberto

2012-09-01

Full Text Available This study evaluates the effect of aging at 550°C on pitting corrosion of Cu10Ni-3Al-1.3Fe alloy, after potentiodynamic polarization test in 0.01 M Na2 SO4 in erosive condition. Cold rolled sheet specimens were solution treated at 900°C for 1 hour, and aged at 550°C until 1,032 hours. The investigation was carried out by potentiodynamic polarization in electrolyte consisted of 0.01 M Na2 SO4 with 10 wt. (% of Al2 O3 abrasive particles. After the polarization tests, specimens were analyzed by optical microscopy and scanning electron microscopy techniques to examine the morphology of the corroded regions. Result show that all samples present a passivity break potential (Eq that characterizes the initiation of pitting corrosion. However, it is not observed any significant change in the value of passivity break potential as a function of aging time. The mechanism of pitting corrosion in the studied alloys can be the passivity breakdown by the action of sulfate ion, followed by growth of pit by galvanic action or dissolution of the copper in cupric and cuprous ions and membrane formation of cuprous oxide over the pit

Effects of Weather Variability on Crop Abandonment

Directory of Open Access Journals (Sweden)

Kelvin Mulungu

2015-03-01

Full Text Available In Zambia, every year some parts of the maize fields are abandoned post-planting. Reasons for this are not clearly known. In this paper, we examine the influence of soil and climatic factors on crop abandonment using a six-year (2007–2012 panel data by modeling the planted-to-harvested ratio (a good indicator of crop abandonment using a fractional and linear approach. Therefore, for the first time, our study appropriately (as supported by the model specification tests that favour fractional probit over linear models the fractional nature of crop abandonment. Regression results, which are not very different between the two specifications, indicate that, more than anything, high rainfall immediately after planting and inadequate fertilizer are the leading determinants of crop abandonment. In the agro-ecological region where dry planting takes place, low temperature during planting months negatively affects the harvested area. The results have implications on the sustainability of farming systems in the face of a changing climate.

Computer simulation of pitting potential measurements

International Nuclear Information System (INIS)

Laycock, N.J.; Noh, J.S.; White, S.P.; Krouse, D.P.

2005-01-01

A deterministic model for the growth of single pits in stainless steel has been combined with a purely stochastic model of pit nucleation. Monte-Carlo simulations have been used to compare the predictions of this model with potentiodynamic experimental measurements of the pitting potential. The quantitative agreement between model and experiment is reasonable for both 304 and 316 stainless steel, and the effects of varying surface roughness, solution chloride concentration and potential sweep rate have been considered

32 CFR 644.494 - Donation, abandonment or destruction.

Science.gov (United States)

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Donation, abandonment or destruction. 644.494 Section 644.494 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL... Land) § 644.494 Donation, abandonment or destruction. (a) General. Improvements may be abandoned...

PIT 9 Project: A private sector initiative

International Nuclear Information System (INIS)

Macdonald, D.W.; Hughes, F.P.; Burton, B.N.

1993-01-01

The Pit 9 Comprehensive Demonstration is intended to demonstrate a cost-effective approach to remediate an Idaho National Engineering Lab. (INEL) waste disposal pit through a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Interim Action. The remediation will include additional requirements, if needed, to provide high confidence that only minor additional work would be necessary to accomplish the final closure as part of the overall final closure strategy for the INEL's Subsurface Disposal Area (SDA). Pit 9 is an inactive waste disposal pit located in the northeastern corner of the SDA at the INEL's Radioactive Waste Management Complex (RWMC). It covers approximately 1 acre. The waste within Pit 9 is primarily transuranic waste generated at the Rocky Flats Plant and additional wastes, both hazardous and low-level radioactive, from generators at the INEL

Who abandons embryos after IVF?

LENUS (Irish Health Repository)

Walsh, A P H

2010-04-01

This investigation describes features of in vitro fertilisation (IVF) patients who never returned to claim their embryos following cryopreservation. Frozen embryo data were reviewed to establish communication patterns between patient and clinic; embryos were considered abandoned when 1) an IVF patient with frozen embryo\\/s stored at our facility failed to make contact with our clinic for > 2 yrs and 2) the patient could not be located after a multi-modal outreach effort was undertaken. For these patients, telephone numbers had been disconnected and no forwarding address was available. Patient, spouse and emergency family contact\\/s all escaped detection efforts despite an exhaustive public database search including death records and Internet directory portals. From 3244 IVF cycles completed from 2000 to 2008, > or = 1 embryo was frozen in 1159 cases (35.7%). Those without correspondence for > 2 yrs accounted for 292 (25.2%) patients with frozen embryos; 281 were contacted by methods including registered (signature involving abandoned embryos did not differ substantially from other patients. The goal of having a baby was achieved by 10\\/11 patients either by spontaneous conception, adoption or IVF. One patient moved away with conception status unconfirmed. The overall rate of embryo abandonment was 11\\/1159 (< 1%) in this IVF population. Pre-IVF counselling minimises, but does not totally eliminate, the problem of abandoned embryos. As the number of abandoned embryos from IVF accumulates, their fate urgently requires clarification. We propose that clinicians develop a policy consistent with relevant Irish Constitutional provisions to address this medical dilemma.

MHD mixed convection flow and heat transfer in an open C-shaped enclosure using water-copper oxide nanofluid

Science.gov (United States)

Armaghani, T.; Esmaeili, H.; Mohammadpoor, Y. A.; Pop, I.

2018-01-01

In this paper, the steady mixed convection flow and heat transfer of water-copper oxide nanofluid in an open C-shaped enclosure is investigated numerically. The enclosure is under constant magnetic field. Effects of Richardson number, magnetic and nanofluid volume fraction parameters are studied and discussed. The nanofluid with a cold temperature of T C and a velocity of u c enters the enclosure from the top right corner and exits from the bottom right corner. The vertical wall of the left side is subjected to a hot and constant temperature T h . Also, other walls are insulated. It is found that the heat transfer is increased via increasing the Hartmann and Reynolds numbers. For low Reynolds numbers, the enhances of the Hartman number leads to a slightly increases of the average Nusselt number, but for high Reynolds numbers, the average Nusselt number gets an ascending trend and the increase in the Hartmann number shows its effect more pronounced. Also, with increase in Ri, the effect of nanofluid on the heat transfer increases. Due to practical impotence, the study of mixed convection heat transfer in enclosures and various shaped of cavities has attracted remarkable attentions in the past few decades. Significant applications of the mixed convection flow can be found in atmospheric flows, solar energy storage, heat exchangers, lubrication technology, drying technologies, cooling of the electronic devices, etc. The present results are original and new for the problem of MHD mixed convection flow and heat transfer in an open C-shaped enclosure using water-copper oxide nanofluid. Comparison of the obtained results with those from the open literature (Mahmoodi et al. [24]) is acceptable.

Analysis of BY-106 pump pit cover plate

International Nuclear Information System (INIS)

Coverdell, B.L.

1994-01-01

A new cover for the pump pit of Tank 241-BY-106 has been designed to allow the rotary core exhauster to be hooked up without requiring pit entry, riser modification, or equipment removal. The new pit cover is necessary to allow installation of two risers for reducing exposure, contamination, and waste. Computer analysis indicates that the safety margin of the pit cover plate with two risers is adequate. The computer stress model and input files are attached. The pit cover plate is a replacement for an existing plate; therefore seismic and wind loads were considered for the plate only

37 CFR 2.66 - Revival of abandoned applications.

Science.gov (United States)

2010-07-01

... Applicants § 2.66 Revival of abandoned applications. (a) The applicant may file a petition to revive an... for filing a petition to revive an application abandoned because the applicant did not timely respond... proposed response. (c) The requirements for filing a petition to revive an application abandoned because...

Structures of Bordered Pits Potentially Contributing to Isolation of a Refilled Vessel from Negative Xylem Pressure in Stems of Morus australis Poir.: Testing of the Pit Membrane Osmosis and Pit Valve Hypotheses.

Science.gov (United States)

Ooeda, Hiroki; Terashima, Ichiro; Taneda, Haruhiko

2017-02-01

Two hypotheses have been proposed to explain the mechanism preventing the refilling vessel water from being drained to the neighboring functional vessels under negative pressure. The pit membrane osmosis hypothesis proposes that the xylem parenchyma cells release polysaccharides that are impermeable to the intervessel pit membranes into the refilling vessel; this osmotically counteracts the negative pressure, thereby allowing the vessel to refill. The pit valve hypothesis proposes that gas trapped within intervessel bordered pits isolates the refilling vessel water from the surrounding functional vessels. Here, using the single-vessel method, we assessed these hypotheses in shoots of mulberry (Morus australis Poir.). First, we confirmed the occurrence of xylem refilling under negative pressure in the potted mulberry saplings. To examine the pit membrane osmosis hypothesis, we estimated the semi-permeability of pit membranes for molecules of various sizes and found that the pit membranes were not semi-permeable to polyethylene glycol of molecular mass osmosis mechanism in mulberry would be unrealistically large. © The Author 2016. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Application of Universal Thermal Climate Index (UTCI) for assessment of occupational heat stress in open-pit mines.

Science.gov (United States)

Nassiri, Parvin; Monazzam, Mohammad Reza; Golbabaei, Farideh; Dehghan, Somayeh Farhang; Rafieepour, Athena; Mortezapour, Ali Reza; Asghari, Mehdi

2017-10-07

The purpose of this article is to examine the applicability of Universal Thermal Climate Index (UTCI) index as an innovative index for evaluating of occupational heat stress in outdoor environments. 175 workers of 12 open-pit mines in Tehran, Iran were selected for this research study. First, the environmental variables such as air temperature, wet-bulb temperature, globe temperature, relative humidity and air flow rate were measured; then UTCI, wet-bulb globe temperature (WBGT) and heat stress index (HSI) indices were calculated. Simultaneously, physiological parameters including heart rate, oral temperature, tympanic temperature and skin temperature of workers were measured. UTCI and WBGT are positively significantly correlated with all environmental parameters (p0.05). Moreover, a strong significant relationship was found between UTCI and WBGT (r=0.95; p<0.001). The significant positive correlations exist between physiological parameters including oral temperature, tympanic and skin temperatures and heart rate and both the UTCI and WBGT indices (p<0.029). The highest correlation coefficient has been found between the UTCI and physiological parameters. Due to the low humidity and air velocity (~<1 m/s) in understudied mines, UTCI index appears to be appropriate to assess the occupational heat stress in these outdoor workplaces.

Lake sediments record prehistoric lead pollution related to early copper production in North America.

Science.gov (United States)

Pompeani, David P; Abbott, Mark B; Steinman, Byron A; Bain, Daniel J

2013-06-04

The mining and use of copper by prehistoric people on Michigan's Keweenaw Peninsula is one of the oldest examples of metalworking. We analyzed the concentration of lead, titanium, magnesium, iron, and organic matter in sediment cores recovered from three lakes located near mine pits to investigate the timing, location, and magnitude of ancient copper mining pollution. Lead concentrations were normalized to lithogenic metals and organic matter to account for processes that can influence natural (or background) lead delivery. Nearly simultaneous lead enrichments occurred at Lake Manganese and Copper Falls Lake ∼8000 and 7000 years before present (yr BP), indicating that copper extraction occurred concurrently in at least two locations on the peninsula. The poor temporal coherence among the lead enrichments from ∼6300 to 5000 yr BP at each lake suggests that the focus of copper mining and annealing shifted through time. In sediment younger than ∼5000 yr BP, lead concentrations remain at background levels at all three lakes, excluding historic lead increases starting ∼150 yr BP. Our work demonstrates that lead emissions associated with both the historic and Old Copper Complex tradition are detectable and can be used to determine the temporal and geographic pattern of metal pollution.

Magnetic surveys for locating abandoned wells

Science.gov (United States)

,

1995-01-01

Abandoned and unrecorded wells may act as conduits for the contamination of groundwater supplies by oil field brines and other pollutants. The casings of abandoned wells eventually develop leaks, which, if not properly plugged, can allow pollutants to reach freshwater aquifers that supply drinking water. Sources of pollutants include brine ponds, landfill sites, agricultural activities, industrial activities, illegal disposal sites, or accidental spills. The problem is particularly acute in regions where there are old petroleum fields or where water wells have been extensively used for agricultural irrigation. Even urban areas can contain wells that were abandoned and concealed during development. Carefully designed ground magnetic or aeromagnetic surveys can be used to locate abandoned wells by mapping the magnetic disturbances or "anomalies" produced by their steel well casings. The U.S. Geological Survey (USGS) can, at the request of other Federal, State, or local agencies, conduct, process, and interpret such surveys, or it can aid in the design and monitoring of contracts for such surveys.

Pit Viper strikes at the Hanford site. Pit maintenance using robotics at the Hanford Tank Farms

International Nuclear Information System (INIS)

Roeder-Smith, Lynne

2002-01-01

The Pit Viper--a remote operations waste retrieval system--was developed to replace manual operations in the valve pits of waste storage tanks at the Hanford Site. The system consists of a typical industrial backhoe fitted with a robotic manipulator arm and is operated remotely from a control trailer located outside of the tank farm. Cameras mounted to the arm and within the containment tent allow the operator to view the entire pit area and operate the system using a joystick. The arm's gripper can grasp a variety of tools that allow personnel to perform cleaning, debris removal, and concrete repair tasks--a more efficient and less dose-intensive process than the previous 'long-pole' method. The project team overcame a variety of obstacles during development and testing of the Pit Viper system, and deployment occurred in Hanford Tank C-104 in December 2001

Population and community profiles of small mammals inhabiting an abandoned oil refinery

International Nuclear Information System (INIS)

McMurry, S.T.; Lochmiller, R.L.; McBee, K.; Burks, S.L.; Quails, C.W. Jr.

1993-01-01

Mark-recapture techniques were used to assess population and community dynamics of resident small mammals on three contaminated and three reference sites located on or near an abandoned oil refinery in Oklahoma. Contaminated sites included areas adjacent to oil sludge containment and sedimentation pits and a land farm for treating oily sludges. Reference sites were selected based on their ecological similarity to contaminated sites. Small mammals were trapped from January 1991 to August 1992 at eight week intervals except during summer and winter during which traps were checked at 3 week intervals. Diversity was typically highest on toxic sites due primarily to the presence of house mice (Mus musculus). Similarity in small mammal community composition between sites differed most in summer. Cotton rats (Sigmodon hispidus) were the most abundant species on all sites. Reproductive activity of adult female cotton rats and survival of trappable cotton rats did not differ between sites. However, minimum number known alive and recruitment of juveniles was highest on references sites, indicating that in-utero and neonatal survival may differ between reference and contaminated sites

Nonomuraea indica sp. nov., novel actinomycetes isolated from lime-stone open pit mine, India.

Science.gov (United States)

Quadri, Syed Raziuddin; Tian, Xin-Peng; Zhang, Jing; Li, Jie; Nie, Guo-Xing; Tang, Shu-Kun; Al Ruwaili, Jamal; Agsar, Dayanand; Li, Wen-Jun; Dastager, Syed G

2015-08-01

A Gram-positive, aerobic, nonmotile actinomycete strain designated DRQ-2(T) was isolated from the soil sample collected from lime-stone open pit mine from the Gulbarga region, Karnataka province, India. Strain DRQ-2(T) was identified as a member of the genus Nonomuraea by a polyphasic approach. Strain DRQ-2(T) could be differentiated from other members of the genus Nonomuraea on the basis of physiology and 16S rRNA gene sequence analysis. The 16S rRNA gene sequence similarity of strain DRQ-2(T) showed highest sequence similarity to Nonomuraea muscovyensis DSM 45913(T) (99.1%), N. salmonea DSM 43678(T) (98.2%) and N. maheshkhaliensis JCM 13929(T) with 98.0%, respectively. Chemotaxonomic properties showing predominant menaquinones of MK-9 (H4), MK-9(H2) and MK-9(H6), major polar lipids comprised diphosphatidylglycerol, phosphatidylmono methyl ethanolamine (PME), phosphatidylethanolamine (PE), hydroxy-PME (OH-PME), hydroxy PE (OH-PEE), phosphatidylglycerol (PG), ninhydrin-positive phosphoglycolipid and unknown phospholipid, fatty acids with major amounts of i-C16:0, ai-C15:0 and ai-C17:0 supported allocation of the strain to the genus Nonomuraea. Results of DNA-DNA hybridization and physiological tests allowed genotypic and phenotypic differentiation of strain DRQ-2(T) from closely related species. The genomic DNA G+C content of the organism was 72.5 mol%. On the basis of phenotypic, chemotypic and molecular characteristics, strain DRQ-2(T) represents a novel species of the genus Nonomuraea, for which the name N. indica sp. nov. is proposed, with type strain DRQ-2(T) (=NCIM 5480(T)= CCTCC AA 209050(T)).

Markov Chain Models for the Stochastic Modeling of Pitting Corrosion

Directory of Open Access Journals (Sweden)

A. Valor

2013-01-01

Full Text Available The stochastic nature of pitting corrosion of metallic structures has been widely recognized. It is assumed that this kind of deterioration retains no memory of the past, so only the current state of the damage influences its future development. This characteristic allows pitting corrosion to be categorized as a Markov process. In this paper, two different models of pitting corrosion, developed using Markov chains, are presented. Firstly, a continuous-time, nonhomogeneous linear growth (pure birth Markov process is used to model external pitting corrosion in underground pipelines. A closed-form solution of the system of Kolmogorov's forward equations is used to describe the transition probability function in a discrete pit depth space. The transition probability function is identified by correlating the stochastic pit depth mean with the empirical deterministic mean. In the second model, the distribution of maximum pit depths in a pitting experiment is successfully modeled after the combination of two stochastic processes: pit initiation and pit growth. Pit generation is modeled as a nonhomogeneous Poisson process, in which induction time is simulated as the realization of a Weibull process. Pit growth is simulated using a nonhomogeneous Markov process. An analytical solution of Kolmogorov's system of equations is also found for the transition probabilities from the first Markov state. Extreme value statistics is employed to find the distribution of maximum pit depths.

W-12 valve pit decontamination demonstration

International Nuclear Information System (INIS)

Benson, C.E.; Parfitt, J.E.; Patton, B.D.

1995-12-01

Waste tank W-12 is a tank in the ORNL Low-Level Liquid Waste (LLLW) system that collected waste from Building 3525. Because of a leaking flange in the discharge line from W-12 to the evaporator service tank (W-22) and continual inleakage into the tank from an unknown source, W-12 was removed from service to comply with the Federal Facilities Agreement requirement. The initial response was to decontaminate the valve pit between tank W-12 and the evaporator service tank (W-22) to determine if personnel could enter the pit to attempt repair of the leaking flange. Preventing the spread of radioactive contamination from the pit to the environment and to other waste systems was of concern during the decontamination. The drain in the pit goes to the process waste system; therefore, if high-level liquid waste were generated during decontamination activities, it would have to be removed from the pit by means other than the available liquid waste connection. Remote decontamination of W-12 was conducted using the General Mills manipulator bridge and telescoping trolley and REMOTEC RM-10 manipulator. The initial objective of repairing the leaking flange was not conducted because of the repair uncertainty and the unknown tank inleakage. Rather, new piping was installed to empty the W-12 tank that would bypass the valve pit and eliminate the need to repair the flange. The radiological surveys indicated that a substantial decontamination factor was achieved

Protection and restoration of soil in mining operations which disrupt the surface of the earth, with the open pit method of working minerals (problems, obtained data and recommendations)

Energy Technology Data Exchange (ETDEWEB)

Debelak, M.

1981-01-01

A critical analysis is made of the current state and the ways to solve the problem of protection and restoration of the sections of the earth's surface and sources of drinking water which can be disrupted with the open pit method of working minerals. The need is advanced for creating a system of coordination and planning of the activity of all the organizations associated with working minerals, restoration operations and inspection of them. The order of preparation for recultivation during mining operations (in particular, storage of the fertile ground) and conducting them after the end of mining are described.

Atmospheric pollution with copper around the copper mine and flotation, 'Buchim', Republic of Macedonia, using biomonitoring moss and lichen technique

International Nuclear Information System (INIS)

Balabanova, Biljana; Bacheva, Katerina; Shajn, Robert; Stafilov, Trajche

2009-01-01

This paper has studied the atmospheric pollution with copper due to copper mining and flotation 'Buchim' near Radovish, Republic of Macedonia. The copper ore and ore tailings continually are exposed to open air, which occur winds carry out the fine particles in to atmosphere. Moss (Hyloconium splendens and Pleurozium schrebery) and lichen (Hypogymnia physodes and Parmelia sulcata) samples were used for biomonitoring the possible atmospheric pollution with copper in the mine vicinity. Moss and lichen samples were digested by using of microwave digestion system and copper was analyzed by atomic emission spectrometry with inductively coupled plasma (ICPAES). The obtained values for the content of copper in moss and lichen samples were statistically processed using the nonparametric and parametric analysis. Maps of areal deposition of copper show an increase content of copper in the vicinity of mine, but long distance distribution of this element is not established yet.

Corrosion of copper under Canadian nuclear fuel waste disposal conditions

International Nuclear Information System (INIS)

King, F.; Litke, C.D.

1990-01-01

The corrosion of copper was studied under Canadian nuclear fuel waste disposal conditions. The groundwater in a Canadian waste vault is expected to be saline, with chloride concentrations from 0.1 to 1.0 mol/l. The container would be packed in a sand/clay buffer, and the maximum temperature on the copper surface would be 100C; tests were performed up to 150C. Radiation fields will initially be around 500 rad/h, and conditions will be oxidizing. Sulfides may be present. The minimum design lifetime for the container is 500 years. Most work has been done on uniform corrosion, although pitting has been considered. It was found that the rate of uniform corrosion in aerated NaCl at room temperature is limited by the rate of the anodic reaction, which is controlled mainly by the rate of transport of dissolved metal species away from the copper surface. The rate of corrosion should become controlled by the transport of oxygen to the copper surface only at very low oxygen concentrations. In the presence of gamma radiation the corrosion rate may never become cathodically transport limited. In compacted buffer material, the corrosion rate appears to be limited by the rate of transport of copper species away from the corroding surface. The authors recommend that long-term predictions of container lifetime should be based on the known rate-determining step for the overall corrosion process. 8 refs

Water pollution from abandoned mines

OpenAIRE

Iversen, E.; Johannessen, M.

1987-01-01

The report provides a country-wide overview of abandoned pyrite mines where operations have been fairly extensive. The water pollution situation is assessed on the basis of reported investigations, inspections and chemical analyses from the individual areas. In cases where larger watercourses (Orkla, Gaula), and the upper stretch of the Glåma are affected the situation appears to be adequately described. However abandoned mine areas may also cause local pollution problems, and here documentat...

Effect of Post Weld Heat Treatment on Corrosion Behavior of AA2014 Aluminum – Copper Alloy Electron Beam Welds

Science.gov (United States)

Venkata Ramana, V. S. N.; Mohammed, Raffi; Madhusudhan Reddy, G.; Srinivasa Rao, K.

2018-03-01

The present work pertains to the study of corrosion behavior of aluminum alloy electron beam welds. The aluminium alloy used in the present study is copper containing AA2014 alloy. Electron Beam Welding (EBW) was used to weld the alloys in annealed (O) condition. Microstructural changes across the welds were recorded and the effect of post weld heat treatment (PWHT) in T4 (Solutionized and naturally aged) condition on pitting corrosion resistance was studied. A software based PAR basic electrochemical system was used for potentio-dynamic polarization tests. From the study it is observed that weld in O condition is prone to more liquation than that of PWHT condition. This may be attributed to re-melting and solidification of excess eutectic present in the O condition of the base metal. It was also observed that slightly higher hardness values are recorded in O condition than that of PWHT condition. The pitting corrosion resistance of the PMZ/HAZ in PWHT condition is better than that of O condition. This is attributed to copper segregation at the grain boundaries of PMZ in O condition.

The Application of Foundation Pit Monitoring Technology to the Excavation

Directory of Open Access Journals (Sweden)

Qiu Jin

2015-01-01

Full Text Available The foundation pit monitoring plays an important role in the foundation pit supporting projects especially in those deep foundation pit projects. Through the whole monitoring of the foundation pit construction from the excavation to the backfill, we can learn about the forcing and deforming process of the foundation pit supporting system, and grasp the impact of external condition changes on the foundation pit. This paper takes a project in Jinan as an example to establish a specific monitoring program, and then conducts the analysis and evaluation of the monitoring data; the real-time grasp of the foundation pit deformation and internal force changes can help to further ensure the security status of the foundation pit, thus better guiding the construction.

Simulating the effect of forces pit ventilation on ammonia emission from naturally ventilated cow houses with CFD

NARCIS (Netherlands)

Sapounas, A.; Campen, J.B.; Smits, M.C.J.; Dooren, van H.J.C.

2009-01-01

Atmospheric NH3, mainly originates from agricultural sources, can cause serious environmental problems related to eutrophication and soil acidification. Emissions from dairy houses are 15% of total agricultural NH3 emissions. Due to open buildings, existing abatement options are limited. Pit air

The analysis of the Tectonics - SSS - Seismicity System in the 3D-model of the Rasvumchorr Mine - Central Open Pit Natural and Technical System (Khibiny)

Science.gov (United States)

Zhirov, Dmitry; Klimov, Sergey; Zhirova, Anzhela; Panteleev, Alexey; Rybin, Vadim

2017-04-01

Main hazardous factors during the operation of deposits represent tectonics (structural dislocation), strain and stress state (SSS), and seismicity. The cause and effect relationships in the Fault Tectonics - SSS - Seismicity system were analyzed using a 3D geological and structural Rasvumchorr Mine - Central Open Pit model. This natural and technical system (NTS) has resulted from the development of the world-class apatite-nepheline deposits the Apatite Circus and Rasvumchorr Plateau. The 3D model integrates various spatial data on the earth's surface topography before and after mining, geometry of mines and dumps, SSS measurements and rock pressure, seismicity, fault tectonics and etc. The analysis of the 3D model has clearly demonstrated the localization of three main seismic emanation zones in the areas of maximum anthropogenic variation of the initial rock state, and namely: ore pass zone under the Southern edge of the Central open pit, collapse and joining zone of the Rasvumchorr Mine and NW edge of the open pit, and zone under the Apatite Circus plate - collapse console. And, on the contrary, in the area of a large dump under the underground mine, a perennial seismic minimum zone was identified. The relation of the seismicity and fault tectonics was revealed only in three local sectors near come certain echelon fissures of the Main Fault(MF). No confinement of increased seismicity areas to the MF and other numerous echelon fissures is observed. The same picture occurs towards manifestations of rock pressure. Only an insignificant part of echelon fissures (including low rank of hierarchy) controls hazardous manifestations of rock pressure (dumps, strong deformations of the mine contour, etc.). It is shown that the anthropogenic factor (explosive, geometry and arrangement of mined spaces and collapse console), as well as the time factor significantly change orientation and structure (contrast and heterogeneity) of the stress fields. Time series of natural

Testing and modeling the influence of reclamation and control methods for reducing nonpoint mercury emissions associated with industrial open pit gold mines.

Science.gov (United States)

Miller, Matthieu B; Gustin, Mae S

2013-06-01

Industrial gold mining is a significant source of mercury (Hg) emission to the atmosphere. To investigate ways to reduce these emissions, reclamation and dust and mercury control methods used at open pit gold mining operations in Nevada were studied in a laboratory setting. Using this information along with field data, and building off previous work, total annual Hg emissions were estimated for two active gold mines in northern Nevada. Results showed that capping mining waste materials with a low-Hg substrate can reduce Hg emissions from 50 to nearly 100%. The spraying of typical dust control solutions often results in higher Hg emissions, especially as materials dry after application. The concentrated application of a dithiocarbamate Hg control reagent appears to reduce Hg emissions, but further testing mimicking the actual distribution of this chemical within an active leach solution is needed to make a more definitive assessment.

Development of broadleaved woodland on colliery and open pit coal mines in the United Kingdom

International Nuclear Information System (INIS)

Humphries, R.N.; McQuire, G.E.

1994-01-01

Broadleaved woodland is an important land use and vegetation type in the United Kingdom (UK), and potentially the most effective landscape and restoration treatment for colliery waste tips and open pit coal sites. A field-based national survey of collieries in England and Wales in 1986 and 1987 showed that establishment was satisfactory in only half of the schemes, and growth was deemed satisfactory in less than one-fifth. There are standard forestry practices whereby stock quality can be assured, and herbaceous vegetation controlled or eliminated by the use of herbicides. During the restoration of the site, depending on choice of species, adequate soil water can be provided by the selection of appropriate soil types and thicknesses, and adoption of appropriate soil handling and decompaction practices. The low affinity of the plantations with local and regional types was partly due to the planting of non-native species and partly due to the failure to match species with site and soil characteristics. There is no reason why woodlands of a local and regional character cannot be established by planting the associated species. A matrix of fast-growing tree and/or shrub species should be used to promote early woodland development. These would be removed during normal management which is essential for the ultimate success of the woodland. Planting schemes should also incorporate woodland structural elements and understory and ground flora species. Provided that these measures are fully implemented, significant improvements in establishment, growth, and woodland development on restored sites should be achieved

Abandoned Shipwreck Act

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data represents the extent of the Abandoned Shipwreck Act (ASA). The ASA allows states to manage a broad range of resources within submerged lands, including...

Detecting pits in tart cherries by hyperspectral transmission imaging

Science.gov (United States)

Qin, Jianwei; Lu, Renfu

2004-11-01

The presence of pits in processed cherry products causes safety concerns for consumers and imposes potential liability for the food industry. The objective of this research was to investigate a hyperspectral transmission imaging technique for detecting the pit in tart cherries. A hyperspectral imaging system was used to acquire transmission images from individual cherry fruit for four orientations before and after pits were removed over the spectral region between 450 nm and 1,000 nm. Cherries of three size groups (small, intermediate, and large), each with two color classes (light red and dark red) were used for determining the effect of fruit orientation, size, and color on the pit detection accuracy. Additional cherries were studied for the effect of defect (i.e., bruises) on the pit detection. Computer algorithms were developed using the neural network (NN) method to classify the cherries with and without the pit. Two types of data inputs, i.e., single spectra and selected regions of interest (ROIs), were compared. The spectral region between 690 nm and 850 nm was most appropriate for cherry pit detection. The NN with inputs of ROIs achieved higher pit detection rates ranging from 90.6% to 100%, with the average correct rate of 98.4%. Fruit orientation and color had a small effect (less than 1%) on pit detection. Fruit size and defect affected pit detection and their effect could be minimized by training the NN with properly selected cherry samples.

Causes, outcome and prevention of abandonment in retinoblastoma in India.

Science.gov (United States)

Kumar, Archana; Moulik, Nirmalya Roy; Mishra, Ravi Krishna; Kumar, Dipak

2013-05-01

The high-cure rates of 90% in retinoblastoma are not replicated in developing countries due to late presentation and poor compliance to treatment. The present study takes a closer look at causes of abandonment of therapy and effectiveness of counselling in reducing abandonment. A retrospective study of children with retinoblastoma registered at our centre from March 2008 through August 2011. Fifty (49.50%) of 101 children registered for treatment abandoned therapy. Abandonment rates were significantly higher in rural as compared to urban children (P = 0.02). There was no significant difference in rate of abandonment between stages or laterality of disease and other socio-demographic factors. Telephone calls were more effective than letters in tracing patients (31.2% vs. 2.4%). Major reasons cited behind abandonment were financial problems (30%) and unwillingness to enucleate (20%). Of the 12 children who returned and were retreated 6 (50%) died of progressive disease. Nineteen (73%) of those who did not return died at home. Abandonment rates steadily declined from 71.42% in 2008 to 16.66% in 2011 (P = 0.01) due to effective pre-abandonment counselling by a support team under the National Retinoblastoma Registry of India from 2009. Abandonment rates for children with retinoblastoma continue to be unacceptably high. Rural background, financial constraints and hesitancy to enucleate were important causes behind abandonment. Outcome of patients who abandoned treatment was uniformly dismal. Inclusion of support team and intensified initial counselling helped in improving compliance. Copyright © 2013 Wiley Periodicals, Inc.

THE ESTIMATION OF DIMENSION AND FACTORS OF SCHOOL ABANDON

Directory of Open Access Journals (Sweden)

Andreea Iluzia IACOB

2011-12-01

Full Text Available During the transition period, in Romania, the dimension of school abandon had risen. The main goals of the study are: to estimate the school abandon rate by each educational level in Romania, to identify the factors which affect school abandon on urban and rural areas and at development regions level; to analyze the causes of earlier school abandon. In the same time, the analysis had also followed the temporal component, by including in the database the last decade statistical information. The school abandon was measured as the difference between the numbers of pupils/students found at the end of the school year and the same category enrolled at the beginning of the same year.

Decommissioning and abandonment of offshore installations

International Nuclear Information System (INIS)

Side, J.C.

1992-01-01

To the onlooker surprising little thought was given at the project planning stage to the fate of offshore facilities once their production lifetimes had come to an end. Throughout the 1970s at least, international law required the complete removal of all structures and installations one disused or abandoned. Fishermen's organisations were led to believe that such installations would be entirely removed yet many of the designs of these show that removal was not much in the minds of the engineers or project management during the design stages. Changes in the text of the United Nations' Convention on the Law of the Sea and (by their widespread legal adoption) in customary international law may now permit partial removal of installations subject to important safeguards for navigation, the environment and other users of the sea. Of the North Sea states at least one has adopted policies that will minimise the cost associated with offshore decommissioning and abandonment and both the UK and Norway are adopting legislation which will provide for a case by case approach to the decommissioning and abandonment of offshore facilities and allow partial removal options. There has thus been a recent and significant change in approach to the abandonment of offshore oil and gas installations. This chapter reviews the development of abandonment laws and policies, outlines the available removal options, and provides a consideration of the environmental and fishery implications of these for the North Sea. (Author)

Pitting of malaria parasites and spherocyte formation

Directory of Open Access Journals (Sweden)

Gichuki Charity W

2006-07-01

Full Text Available Abstract Background A high prevalence of spherocytes was detected in blood smears of children enrolled in a case control study conducted in the malaria holoendemic Lake Victoria basin. It was speculated that the spherocytes reflect intraerythrocytic removal of malarial parasites with a concurrent removal of RBC membrane through a process analogous to pitting of intraerythrocytic inclusion bodies. Pitting and re-circulation of RBCs devoid of malaria parasites could be a host mechanism for parasite clearance while minimizing the anaemia that would occur were the entire parasitized RBC removed. The prior demonstration of RBCs containing ring-infected erythrocyte surface antigen (pf 155 or RESA but no intracellular parasites, support the idea of pitting. Methods An in vitro model was developed to examine the phenomenon of pitting and spherocyte formation in Plasmodium falciparum infected RBCs (iRBC co-incubated with human macrophages. In vivo application of this model was evaluated using blood specimens from patients attending Kisumu Ditrict Hospital. RBCs were probed with anti-RESA monoclonal antibody and a DNA stain (propidium iodide. Flow cytometry and fluorescent microscopy was used to compare RBCs containing both the antigen and the parasites to those that were only RESA positive. Results Co-incubation of iRBC and tumor necrosis factor-alpha activated macrophages led to pitting (14% ± 1.31% macrophages with engulfed trophozoites as opposed to erythrophagocytosis (5.33% ± 0.95% (P Conclusion It is proposed that in malaria holoendemic areas where prevalence of asexual stage parasites approaches 100% in children, RBCs with pitted parasites are re-circulated and pitting may produce spherocytes.

Arsenic, copper and zinc occurrence at the Wangaloa coal mine, southeast Otago, New Zealand

International Nuclear Information System (INIS)

Black, A.; Craw, D.

2001-01-01

Waste piles, created from open cast coal mining activities at the abandoned Wangaloa mine in SE Otago, have exposed pyrite (FeS 2 ) to atmospheric conditions. This has led to the acidification of the surface tailings and nearby drainage waters (acid mine drainage, AMD). Mobilisation of trace metals arsenic (As), copper (Cu), and zinc (Zn) has occurred, partly as a result of the low pH levels (ca. pH 2-4), leading to elevated concentrations of these metals in receiving waters. Authigenic pyrite deposited in a marginal marine coal-forming environment is enriched in As with levels reaching up to 100 ppm. Copper and Zn in solid solution are not elevated above background levels in either coal measures or associated pyrite. Water discharges, sediments, waste rock and background samples were sampled and analysed during the driest (summer) and wettest (winter) seasons of 1998 and 1999. During the winter season, water discharging from the waste piles contained up to 0.7 ppm (mg/kg) As, as measured in 1998. During the 1999 wettest season, no such levels of As were observed, with the highest level attaining 0.07 ppm As. Copper and Zn were locally elevated in waters, with Zn concentrations reaching 1 ppm. During the summer season of 1999, only one sampling site recorded elevated metal concentrations. Adverse effects from the remnant waste piles appear to be highly localised due to downstream natural remediation processes occurring in a wetland area. The absence of strongly elevated metal concentrations during the drier season is a result of strongly depressed water levels within the waste piles. Flushing of acid and metals occurs when the water levels increase with the onset of the winter season. During the summer season, pyrite within the waste piles has been readily decomposing from the increased availability and transport of atmospheric oxygen

Uniform and pitting corrosion events induced by SCN- anions on Al alloys surfaces and the effect of UV light

International Nuclear Information System (INIS)

Amin, Mohammed A.

2011-01-01

The influence of the alloying elements on the uniform and pitting corrosion processes of Al-6061, Al-4.5%Cu, Al-7.5%Cu, Al-6%Si and Al-12%Si alloys was studied in 0.50 M KSCN solution at 25 o C. Open-circuit potential, Tafel polarization, linear polarization resistance (LPR) and ICP-AES measurements were used to study the uniform corrosion process on the surfaces of the tested alloys. Cyclic polarization, potentiostatic current-time transients and impedance techniques were employed for pitting corrosion studies. Obtained results were compared with pure Al. Passivation kinetics of the tested Al samples were also studied as a function of applied potential, [SCN - ] and sample composition by means of potentiostatic current transients. The induction time, after which the growth of stable pits occurs, decreased with increasing applied potential and [SCN - ]. Regarding to uniform corrosion, alloyed Cu was found to enhance the corrosion rate, while alloyed Si suppressed it. Alloying elements of the tested samples diminished pitting attack to an extent depending on the percentage of the alloying element in the sample. Among the investigated materials, Al-Si alloys exhibited the highest corrosion resistance towards uniform and pitting corrosion processes in KSCN solutions. The passive and dissolution behaviour of Al was also studied under the conditions of continuous illumination (300-450 nm) based on cyclic polarization and potentiostatic techniques. The incident photons had a little influence on pit initiation and a marked effect on pit growth. These explained in terms of a photo-induced modification of the passive film formed on the anode surface, which render it more resistant to pitting. The effects of UV photons energy and period of illumination on the morphology of the pitted surfaces were also studied.

Copper atomic-scale transistors.

Science.gov (United States)

Xie, Fangqing; Kavalenka, Maryna N; Röger, Moritz; Albrecht, Daniel; Hölscher, Hendrik; Leuthold, Jürgen; Schimmel, Thomas

2017-01-01

We investigated copper as a working material for metallic atomic-scale transistors and confirmed that copper atomic-scale transistors can be fabricated and operated electrochemically in a copper electrolyte (CuSO 4 + H 2 SO 4 ) in bi-distilled water under ambient conditions with three microelectrodes (source, drain and gate). The electrochemical switching-on potential of the atomic-scale transistor is below 350 mV, and the switching-off potential is between 0 and -170 mV. The switching-on current is above 1 μA, which is compatible with semiconductor transistor devices. Both sign and amplitude of the voltage applied across the source and drain electrodes ( U bias ) influence the switching rate of the transistor and the copper deposition on the electrodes, and correspondingly shift the electrochemical operation potential. The copper atomic-scale transistors can be switched using a function generator without a computer-controlled feedback switching mechanism. The copper atomic-scale transistors, with only one or two atoms at the narrowest constriction, were realized to switch between 0 and 1 G 0 ( G 0 = 2e 2 /h; with e being the electron charge, and h being Planck's constant) or 2 G 0 by the function generator. The switching rate can reach up to 10 Hz. The copper atomic-scale transistor demonstrates volatile/non-volatile dual functionalities. Such an optimal merging of the logic with memory may open a perspective for processor-in-memory and logic-in-memory architectures, using copper as an alternative working material besides silver for fully metallic atomic-scale transistors.

Research process of nondestructive testing pitting corrosion in metal material

Directory of Open Access Journals (Sweden)

Bo ZHANG

2017-12-01

Full Text Available Pitting corrosion directly affects the usability and service life of metal material, so the effective nondestructive testing and evaluation on pitting corrosion is of great significance for fatigue life prediction because of data supporting. The features of pitting corrosion are elaborated, and the relation between the pitting corrosion parameters and fatigue performance is pointed out. Through introducing the fundamental principles of pitting corrosion including mainly magnetic flux leakage inspection, pulsed eddy current and guided waves, the research status of nondestructive testing technology for pitting corrosion is summarized, and the key steps of nondestructive testing technologies are compared and analyzed from the theoretical model, signal processing to industrial applications. Based on the analysis of the signal processing specificity of different nondestructive testing technologies in detecting pitting corrosion, the visualization combined with image processing and signal analysis are indicated as the critical problems of accurate extraction of pitting defect information and quantitative characterization for pitting corrosion. The study on non-contact nondestructive testing technologies is important for improving the detection precision and its application in industries.

The U.S. Forest Service abandoned mine land inventory in Colorado: Background, progress, and preliminary findings

International Nuclear Information System (INIS)

Sares, M.A.

1996-01-01

The U.S. Forest Service (USFS) and the Colorado Geological Survey (CGS) are continuing a cooperative agreement to identify sites of environmental degradation associated with abandoned and inactive mines on Colorado's USFS administered lands. The USFS Abandoned Mine Land Inventory Project is a open-quotes discoveryclose quotes process and is a precursor to the Environmental Protection Agency's open-quotes Preliminary Assessmentclose quotes process. Identification of environmentally degraded sites may lead to a formal Preliminary Assessment. The inventory process begins in the office and involves reviewing existing mining and geologic literature, previous mine inventory work, current and historical maps, water quality information, and aerial photographs. During field investigation, each mine feature is given a unique identification number. Field geologists collect data on the physical and geographic characteristics of the mine features along with information on any water emanating from or interacting with the mine features. This information is used to assign a qualitative environmental degradation rating to the individual mine feature. Guidelines for the rating system are given to field personnel to facilitate consistency within the data set. All data collected are entered into a computer database. From a computer perspective, both location and attribute data are being collected. Therefore, the data are well suited for integration into a geographic information system (GIS) creating a geo-referenced data set. The USFS Abandoned Mine Land Inventory Project began in 1991 and is ongoing. To date, field inventories of the Arapaho, Roosevelt, Pike, and Rio Grande National Forests have been completed. Work in the San Isabel, San Juan, White River, Gunnison, Uncompahgre, and Grand Mesa National Forests is in progress. Through the 1994 field season approximately 9,667 mine features (openings, dumps, tailings, highwalls, etc.) have been inventoried

A study of natural recovery in an aquatic ecosystem affected by mining: the Rodrigatos stream (El Bierzo, Leon, Spain)

International Nuclear Information System (INIS)

Lacal, M.; Herrero, T.; Rodriguez, V.; Alberruche, E.; Vadillo, L.

2009-01-01

This work takes place into the Bierzo Region, located in northeast of the province of Leon (Spain). In this area numerous open-pit and underground coal mines exist. Some of them are still in activity but almost have been abandoned. In any case, mining implies the presence of coal adits, spoil dumps, tailing dams, and coal-washing plants at the river bank. Most of them persist when mining have finished. (Author)

An application of discrete mathematics in the design of an open pit mine

Energy Technology Data Exchange (ETDEWEB)

Caccetta, L.; Giannini, L.M.

1988-09-01

The determination of the 'optimum pit limit' of a mine is considered to be a fundamental problem in mine planning as it provides information which is essential in the evaluation of the economic potential of a mineral deposit, and in the formulation of long-, intermediate-, and short-range mine plans. A number of mathematical techniques have been proposed to solve this problem, some of the more elaborate ones posing considerable computational problems. In this paper we discuss the development and implementation of a graph-theoretic technique originally proposed by Lerchs and Grossman. Our implementation strategy involves the use of a dynamic programming technique to 'bound' the optimum. 19 refs., 4 figs.

Abandonment of nicotine dependence treatment: A cohort study

Directory of Open Access Journals (Sweden)

Maritza Muzzi Cardozo Pawlina

Full Text Available CONTEXT AND OBJECTIVE: Non-adherence to treatment is one of the hindering factors in the process of smoking cessation. This study aimed to compare sociodemographic characteristics, smoking status and motivation among smokers who maintained or abandoned treatment to stop smoking, and to analyze associations between sociodemographic factors and smoking. DESIGN AND SETTING: Cohort study on 216 smokers who were attended at healthcare units in Cuiabá, Mato Grosso. METHODS: The instruments used were the Fagerström, URICA and CAGE questionnaires. Data from the initial evaluation was analyzed using the two-proportion test (α < 0.05. The patients were monitored for six months and those who abandoned treatment were accounted for. Bivariate analysis was conducted, using crude prevalence ratios and 5% significance level (P < 0.05, with abandonment of treatment as the outcome variable. Associations with P < 0.20 were selected for multiple robust Poisson regression (RPa. RESULTS: The abandonment rate was 34.26%. Males and individuals in the 20-39 age group, in employment, with low motivation, with shorter time smoking and lower tobacco intake predominated in the dropout group. In the final model, gender (RPa 1.47; 95% CI: 1.03-2.10 and age group (RPa 3.77; 95% CI: 1.47-9.67 remained associated with abandonment. CONCLUSION: Males and individuals in the 20-39 age group, in employment, with low motivation, with shorter time smoking and lower tobacco intake more frequently abandoned the treatment. Male gender and younger age group were associated with abandonment of nicotine dependence treatment.

Spontaneous Resolution of Optic Disc Pit Maculopathy

OpenAIRE

Tripathy, Koushik

2017-01-01

I read with interest the article reporting spontaneous resolution of optic disc pit maculopathy in a boy.1 Though the presence of an optic disc pit and associated macular involvement is undoubted in the presented case, the provided optical coherence tomography (OCT) does not clearly show typical intraretinal schisis (Figure 1B)1 at multiple retinal levels which may communicate with the pit. Instead, it shows a sub-internal limiting membrane (sub-ILM) cavity. Such cavities are known to occur f...

The Abandonment of an Active Lifestyle Within University Students: Reasons for Abandonment and Expectations of Re-Engagement

Directory of Open Access Journals (Sweden)

Manuel Gómez-López

2011-08-01

Full Text Available The objective of this research is to analyse in detail the barriers that make university students abandon the practice of physical activity and adopt a sedentary lifestyle. In order to do so, a questionnaire on the analysis of sports habits and lifestyles was administered to 795 students who stated not having done any physical and/or sports activity for at least one year at the moment of the field-work. A factorial, descriptive and correlation analysis was carried out. The results reveal that university students abandon a healthy lifestyle mainly due to external barriers particularly because of lack of time. On the one hand, women appear to be the ones who, to a great extent, adopt a sedentary lifestyle. On the other hand, men are the ones who refer more to abandoning the practice of physical activity due to internal barriers. The majority of the university students gave up practicing sport before entering university alluding to external barriers as their reason for the abandonment. A greater part of the sedentary university students expressing that they will be active in the future, left the practice of sport due to internal barriers.

Cytogenetic instability in populations with residential proximity to open-pit coal mine in Northern Colombia in relation to PM10 and PM2.5 levels.

Science.gov (United States)

Espitia-Pérez, Lyda; da Silva, Juliana; Espitia-Pérez, Pedro; Brango, Hugo; Salcedo-Arteaga, Shirley; Hoyos-Giraldo, Luz Stella; de Souza, Claudia T; Dias, Johnny F; Agudelo-Castañeda, Dayana; Valdés Toscano, Ana; Gómez-Pérez, Miguel; Henriques, João A P

2018-02-01

Epidemiological studies indicate that living in proximity to coal mines is correlated with numerous diseases including cancer, and that exposure to PM 10 and PM 2.5 components could be associated with this phenomenon. However, the understanding of the mechanisms by which PM exerts its adverse effects is still incomplete and comes mainly from studies in occupationally exposed populations. The aims of this study were to: (1) evaluate DNA damage in lymphocytes assessing the cytokinesis-block micronucleus cytome assay (CBMN-cyt) parameters; (2) identify aneugenic or clastogenic effects in lymphocytes of exposed populations using CREST immunostaining for micronuclei; (3) evaluate multi-elemental composition of atmospheric particulate matter; and (4) verify relation between the DNA damage and PM 2.5 and PM 10 levels around the mining area. Analysis revealed a significant increase in micronuclei frequency in binucleated (MNBN) and mononucleated (MNMONO) cells of individuals with residential proximity to open-pit coal mines compared to residents from non-mining areas. Correlation analysis demonstrated a highly significant association between PM 2.5 levels, MNBN frequencies and CREST+ micronuclei induction in exposed residents. These results suggest that PM 2.5 fraction generated in coal mining activities may induce whole chromosome loss (aneuploidy) preferentially, although there are also chromosome breaks. Analysis of the chemical composition of PM 2.5 by PIXE demonstrated that Si, S, K and Cr concentrations varied significantly between coal mining and reference areas. Enrichment factor values (EF) showed that S, Cr and Cu were highly enriched in the coal mining areas. Compared to reference area, mining regions had also higher concentrations of extractable organic matter (EOM) related to nonpolar and polar compounds. Our results demonstrate that PM 2.5 fraction represents the most important health risk for residents living near open-pit mines, underscoring the need for

Radium and heavy metal transport beneath an abandoned uranium tailings dam

International Nuclear Information System (INIS)

Jeffery, J.J.; Sinclair, G.; Lowson, R.T.

1988-09-01

An abandoned uranium tailings dam at Moline in the Northern Territory of Australia was the site of a study to assess the movement of potentially toxic elements from tailings into subsoil. The tailings at Moline were first laid down in 1959 and have since been leached by prevailing rainfall. Sixteen sampling sites were selected to give a good representation of the dam. At each site, a trench was excavated through the tailings and into the subsoil, then samples of subsoil were taken at 10 cm intervals down to a depth of 50 cm. A sample of the tailings overlying the tailings-subsoil interface was also taken. Samples were analysed for radium, uranium, copper, zinc, and lead. At most sites there was only minor accumulation of these elements in the 0-10 cm subsoil layer immediately below the interface, with concentrations typically one or two orders of magnitude less than the concentrations in overlying tailings. Below 10 cm, the concentrations were typically at or close to background concentrations

Cultural Meanings and Consumers’ Discourses about Their Brand Abandonment

Directory of Open Access Journals (Sweden)

Filipe Diniz

2018-03-01

Full Text Available Although we know a lot about how brand meanings are created and perpetuated in relation to and through cultural discourses, remarkably little work has been done in the marketing field to develop a better comprehension as to how brand meanings are enacted through distancing behaviors, such as brand abandonment. In the marketing literature, abandonment has usually been associated with relationship crises, most commonly as the result of consumer dissatisfaction. This study investigates consumers who abandoned previously consumed brands in two distinct product categories, soft drinks and automobiles. Through investigation of two emblematic brands – CocaCola and Fiat - the analysis illustrates cultural discourses that consumers use to give meanings and socially negotiate their brand abandonment. Considering the repertoire of meanings attached to both the brands and consumers’ commitment to their distancing behavior, the analysis presents three types of brand abandonment: (a contingent, (b balanced and (c aversive. This paper also presents brand abandonment as an enabler of social distinctions, highlighting two discrete discourses promulgated and perpetuated by consumers: (a Life evolution, and (b Rationality, self-control and sovereignty.

Formation of Mesoherpetobionts Communities on a Reclamated Coal Open Pit Dump

Science.gov (United States)

Luzyanin, Sergey; Eremeeva, Natalya

2017-11-01

The structure of the mesoherpetobionts arthropod communities of the reclamated dump of the Krasnobrodsky coal pit (Kemerovo region, Russia) has been studied. It was established that the pioneer grouping of mesoherpetobionts arthropod represented by classes of Chilopoda, Arachnida and Insecta-Ectognatha has been formed on the dump for two years after the soil deposition. From the Arachnida, the species of the order Aranei are the most active in the stocking of the dumps. From the class Chilopoda, the species of Lithobiomorpha appear the first on the dump. Insects from the following three orders, Heteroptera, Hymenoptera and especially Coleoptera take the main part in the expansion of dumps and the formation of primary communities. Among the Coleoptera, the beetles of the family of Carabidae (44 species, dynamic density 22.9 specimens/10 trapped per day) dominate. From them, small or medium-sized species are mainly involved in stocking the dumps. There are significant differences in the complexes of ground dump carabid beetles in comparison with the control group, differing in species composition of dominant species, species richness and species diversity parameters

Pemodelan Penyebaran Batuan Potensial Pembentuk Asam Pada Kawasan Penambangan Batubara Tambang Terbuka Di Muara Lawa, Kabupaten Kutai Barat, Kalimantan Timur (Modeling Distribution of Rock Potential Acid Forming in Open Pit Coal Mining Areas)

OpenAIRE

Devy, Shalaho Dina; Hendrayana, Heru; Putra, Dony Prakasa Eka; Sugiharto, Eko

2016-01-01

The impact of open pit coal mining is the emergence of Acid Mine Water (AMD) around the mining environment that affect the quality of the mine water, aquatic biota, water and soil quality. Therefore, early information to anticipate these impacts is the identification potential acid rock and distribution model as a guide for the mining plan. Geological and geochemical study of rocks is important in knowing the distribution of rock Potential Acid Formning (PAF) and Non Acid Forming (NAF). Minin...

Infanticide and illegal infant abandonment in Malaysia.

Science.gov (United States)

Razali, Salmi; Kirkman, Maggie; Ahmad, S Hassan; Fisher, Jane

2014-10-01

Infant abandonment and infanticide are poorly understood in Malaysia. The information available in the public arena comes predominantly from anecdotal sources. The aim of this study was to describe the prevalence and characteristics of infanticide and illegal infant abandonment in Malaysia and to estimate annual rates for the most recent decade. Summaries of data about infanticide and illegal infant abandonment were gathered from police records; the annual number of live births was ascertained from the national registry. The estimated inferred infanticide rates for Malaysia were compared with the infanticide rates among countries of very high, high, medium, and low rankings on the Human Development, Gender Inequality, and Gini indices. From 1999 to 2011, 1,069 cases of illegal infant abandonment were recorded and 1,147 people were arrested as suspected perpetrators. The estimated inferred infanticide rate fluctuated between 4.82 and 9.11 per 100,000 live births, a moderate rate relative to the infanticide rates of other countries. There are substantial missing data, with details undocumented for about 78-87% of cases and suspected perpetrators. Of the documented cases, it appeared that more boys than girls were victims and that suspected perpetrators were predominantly Malays who were women, usually mothers of the victim; the possibility of arrest bias must be acknowledged. Economic and social inequality, particularly gender inequality, might contribute to the phenomena of infanticide and abandonment. Strategies to reduce rates of infanticide and illegal infant abandonment in Malaysia will require strengthening of the surveillance system and attention to the gender-based inequalities that underpin human development. Copyright © 2014 Elsevier Ltd. All rights reserved.

The WISMUT sanitation project - moving of spoil banks and sanitation work on abandoned open pits

International Nuclear Information System (INIS)

Thie, F.W.

2002-01-01

Ten years after they were started, remedial measures have taken effect in all sites of the WISMUT GmbH. Of the 13 billion DM provided by the German state, about 7.2 billion have been spent - 3.9 billion in eastern Thuringia and 3.3 million in Saxony. A programme of about 480 million DM was completed successfully in 2001. The work also had a positive effect on regional industries as sub-contracts in the order of 180 to 2000 million DM per annum were allotted [de

Improvement in treatment abandonment in pediatric patients with cancer in Guatemala.

Science.gov (United States)

Alvarez, Elysia; Seppa, Midori; Rivas, Silvia; Fuentes, Lucia; Valverde, Patricia; Antillón-Klussmann, Federico; Castellanos, Mauricio; Sweet-Cordero, E Alejandro; Messacar, Kevin; Kurap, John; Bustamante, Marisol; Howard, Scott C; Efron, Bradley; Luna-Fineman, Sandra

2017-10-01

Treatment refusal and abandonment are major causes of treatment failure for children with cancer in low- and middle-income countries (LMICs), like Guatemala. This study identified risk factors for and described the intervention that decreased abandonment. This was a retrospective study of Guatemalan children (0-18 years) with cancer treated at the Unidad Nacional de Oncología Pediátrica (UNOP), 2001-2008, using the Pediatric Oncology Network Database. Treatment refusal was a failure to begin treatment and treatment abandonment was a lapse of 4 weeks or longer in treatment. The impact of medicina integral, a multidisciplinary psychosocial intervention team at UNOP was evaluated. Cox proportional hazards analysis identified the effect of demographic and clinical factors on abandonment. Kaplan-Meier analysis estimated the survival. Of 1,789 patients, 21% refused or abandoned treatment. Abandonment decreased from 27% in 2001 to 7% in 2008 following the implementation of medicina integral. Factors associated with increased risk of refusal and abandonment: greater distance to the centre (P < 0.001), younger age (P = 0.017) and earlier year of diagnosis (P < 0.001). Indigenous race/ethnicity (P = 0.002) was associated with increased risk of abandonment alone. Abandonment correlated with decreased overall survival: 0.57 ± 0.02 (survival ± standard error) for those who completed therapy versus 0.06 ± 0.02 for those who abandoned treatment (P < 0.001) at 8.3 years. This study identified distance, age, year of diagnosis and indigenous race/ethnicity as risk factors for abandonment. A multidisciplinary intervention reduced abandonment and can be replicated in other LMICs. © 2017 Wiley Periodicals, Inc.

Modelling assessment of End Pit Lakes meromictic potential

International Nuclear Information System (INIS)

2006-11-01

The use of End Pit Lakes have been proposed as a remediation solution for oil sands reclamation and operational waters. This report modelled the main factors controlling the occurrence of stratification in Pit Lakes in order to establish design and management guidelines for the Cumulative Environmental Management Association's End Pit Lake Sub-group. The study focused on End Pit Lake size, depth, starting lake salinity concentrations, inflow rates and inflow salinity flux, and investigated their influence on density gradients. One-dimensional modelling and limited 2-D modelling simulations were conducted to examine meromictic potential for a large range of End Pit Lake configurations and conditions. Modelling results showed that fall is the governing season for determining meromixis. The expelling of salt from saline water upon ice formation and its effect on stratification potential and the effect of fresh water loading on stratification potential during spring melt events were not observed to be dominant factors governing meromictic potential for the scenarios examined in the study. Results suggested that shallow End Pit Lakes showed a high turn-over rate with seasonal heating and cooling cycles. Moderately deep End Pit Lakes demonstrated a meromictic potential that was inversely proportional to lake size and require higher starting salinities. With a 2 or 10 million m 3 /yr inflow rate and a 5 parts per thousand starting salinity, a 50 m deep End Pit Lake achieved meromixis at all 3 size ranges considered in the study. Results also showed that the rate of influent salinity decrease was the least important of the parameters influencing meromixis. It was observed that meromixis was a temporary condition in all of the End Pit Lake scenarios envisioned due to the lack of a constant, positive salt replenishment over the long term. It was concluded that further 3-D modelling is required to represent littoral areas as well as to account for extreme winter conditions. A

Pit Study, Geographic NAD83, LOSCO (1999) [pit_study_LOSCO_1998

Data.gov (United States)

Louisiana Geographic Information Center — The 'Pit Study' was meant to identify the remnants of former oil extraction sites which pose the threat of creating an oil spill. These remnants include many other...

Geospatial analysis of residential proximity to open-pit coal mining areas in relation to micronuclei frequency, particulate matter concentration, and elemental enrichment factors.

Science.gov (United States)

Espitia-Pérez, Lyda; Arteaga-Pertuz, Marcia; Soto, José Salvador; Espitia-Pérez, Pedro; Salcedo-Arteaga, Shirley; Pastor-Sierra, Karina; Galeano-Páez, Claudia; Brango, Hugo; da Silva, Juliana; Henriques, João A P

2018-05-03

During coal surface mining, several activities such as drilling, blasting, loading, and transport produce large quantities of particulate matter (PM) that is directly emitted into the atmosphere. Occupational exposure to this PM has been associated with an increase of DNA damage, but there is a scarcity of data examining the impact of these industrial operations in cytogenetic endpoints frequency and cancer risk of potentially exposed surrounding populations. In this study, we used a Geographic Information Systems (GIS) approach and Inverse Distance Weighting (IDW) methods to perform a spatial and statistical analysis to explore whether exposure to PM 2.5 and PM 10 pollution, and additional factors, including the enrichment of the PM with inorganic elements, contribute to cytogenetic damage in residents living in proximity to an open-pit coal mining area. Results showed a spatial relationship between exposure to elevated concentrations of PM 2.5, PM 10 and micronuclei frequency in binucleated (MNBN) and mononucleated (MNMONO) cells. Active pits, disposal, and storage areas could be identified as the possible emission sources of combustion elements. Mining activities were also correlated with increased concentrations of highly enriched elements like S, Cu and Cr in the atmosphere, corroborating its role in the inorganic elements pollution around coal mines. Elements enriched in the PM 2.5 fraction contributed to increasing of MNBN but seems to be more related to increased MNMONO frequencies and DNA damage accumulated in vivo. The combined use of GIS and IDW methods could represent an important tool for monitoring potential cancer risk associated to dynamically distributed variables like the PM. Copyright © 2018. Published by Elsevier Ltd.

Markov chain modelling of pitting corrosion in underground pipelines

Energy Technology Data Exchange (ETDEWEB)

Caleyo, F. [Departamento de Ingenieri' a Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, Mexico D. F. 07738 (Mexico)], E-mail: fcaleyo@gmail.com; Velazquez, J.C. [Departamento de Ingenieri' a Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, Mexico D. F. 07738 (Mexico); Valor, A. [Facultad de Fisica, Universidad de La Habana, San Lazaro y L, Vedado, 10400 La Habana (Cuba); Hallen, J.M. [Departamento de Ingenieri' a Metalurgica, ESIQIE, IPN, UPALM Edif. 7, Zacatenco, Mexico D. F. 07738 (Mexico)

2009-09-15

A continuous-time, non-homogenous linear growth (pure birth) Markov process has been used to model external pitting corrosion in underground pipelines. The closed form solution of Kolmogorov's forward equations for this type of Markov process is used to describe the transition probability function in a discrete pit depth space. The identification of the transition probability function can be achieved by correlating the stochastic pit depth mean with the deterministic mean obtained experimentally. Monte-Carlo simulations previously reported have been used to predict the time evolution of the mean value of the pit depth distribution for different soil textural classes. The simulated distributions have been used to create an empirical Markov chain-based stochastic model for predicting the evolution of pitting corrosion depth and rate distributions from the observed properties of the soil. The proposed model has also been applied to pitting corrosion data from pipeline repeated in-line inspections and laboratory immersion experiments.

Markov chain modelling of pitting corrosion in underground pipelines

International Nuclear Information System (INIS)

Caleyo, F.; Velazquez, J.C.; Valor, A.; Hallen, J.M.

2009-01-01

A continuous-time, non-homogenous linear growth (pure birth) Markov process has been used to model external pitting corrosion in underground pipelines. The closed form solution of Kolmogorov's forward equations for this type of Markov process is used to describe the transition probability function in a discrete pit depth space. The identification of the transition probability function can be achieved by correlating the stochastic pit depth mean with the deterministic mean obtained experimentally. Monte-Carlo simulations previously reported have been used to predict the time evolution of the mean value of the pit depth distribution for different soil textural classes. The simulated distributions have been used to create an empirical Markov chain-based stochastic model for predicting the evolution of pitting corrosion depth and rate distributions from the observed properties of the soil. The proposed model has also been applied to pitting corrosion data from pipeline repeated in-line inspections and laboratory immersion experiments.

Pipeline abandonment: a discussion paper on technical and environmental issues

International Nuclear Information System (INIS)

Etherington, K.

1996-01-01

Formation of government/industry joint steering committee to oversee a review of pipeline abandonment and preparation of a discussion paper was reported. The review became urgent in view of the fact that many of the pipeline systems are nearing the end of their useful life, and the current absence of guidelines in Canada to deal with pipeline abandonment, or to offer guidance on ways of assessing abandonment costs and funding. In view of this situation the safety and the environmental, financial, and legal implications of abandoned pipelines have become an increasing concern to regulatory authorities and the oil and gas industry. Issues to be dealt with in the discussion paper include subsidence, contamination, water crossing, erosion, land management, restoration, utility and pipeline crossings, creation of water conduits, the cost of abandonment, operator choice of abandonment options, and the level of surface disturbance associated with such options

Force-displacement measurements of earlywood bordered pits using a mesomechanical tester.

Science.gov (United States)

Zelinka, Samuel L; Bourne, Keith J; Hermanson, John C; Glass, Samuel V; Costa, Adriana; Wiedenhoeft, Alex C

2015-10-01

The elastic properties of pit membranes are reported to have important implications in understanding air-seeding phenomena in gymnosperms, and pit aspiration plays a large role in wood technological applications such as wood drying and preservative treatment. Here we present force-displacement measurements for pit membranes of circular bordered pits, collected on a mesomechanical testing system. The system consists of a quartz microprobe attached to a microforce sensor that is positioned and advanced with a micromanipulator mounted on an inverted microscope. Membrane displacement is measured from digital image analysis. Unaspirated pits from earlywood of never-dried wood of Larix and Pinus and aspirated pits from earlywood of dried wood of Larix were tested to generate force-displacement curves up to the point of membrane failure. Two failure modes were observed: rupture or tearing of the pit membrane by the microprobe tip, and the stretching of the pit membrane until the torus was forced out of the pit chamber through the pit aperture without rupture, a condition we refer to as torus prolapse. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

Estuarine abandoned channel sedimentation rates record peak fluvial discharge magnitudes

Science.gov (United States)

Gray, A. B.; Pasternack, G. B.; Watson, E. B.

2018-04-01

Fluvial sediment deposits can provide useful records of integrated watershed expressions including flood event magnitudes. However, floodplain and estuarine sediment deposits evolve through the interaction of watershed/marine sediment supply and transport characteristics with the local depositional environment. Thus extraction of watershed scale signals depends upon accounting for local scale effects on sediment deposition rates and character. This study presents an examination of the balance of fluvial sediment dynamics and local scale hydro-geomorphic controls on alluviation of an abandoned channel in the Salinas River Lagoon, CA. A set of three sediment cores contained discrete flood deposits that corresponded to the largest flood events over the period of accretion from 1969 to 2007. Sedimentation rates scaled with peak flood discharge and event scale sediment flux, but were not influenced by longer scale hydro-meteorological activities such as annual precipitation and water yield. Furthermore, the particle size distributions of flood deposits showed no relationship to event magnitudes. Both the responsiveness of sedimentation and unresponsiveness of particle size distributions to hydro-sedimentological event magnitudes appear to be controlled by aspects of local geomorphology that influence the connectivity of the abandoned channel to the Salinas River mainstem. Well-developed upstream plug bar formation precluded the entrainment of coarser bedload into the abandoned channel, while Salinas River mouth conditions (open/closed) in conjunction with tidal and storm surge conditions may play a role in influencing the delivery of coarser suspended load fractions. Channel adjacent sediment deposition can be valuable records of hydro-meteorological and sedimentological regimes, but local depositional settings may dominate the character of short term (interdecadal) signatures.

Meanings of Consumption and Abandonment: Understanding Smoking Cessation Symbolism

Directory of Open Access Journals (Sweden)

Maribel Carvalho Suarez

2014-04-01

Full Text Available In consumption studies, very little attention has been focused on investigating abandonment and, more specifically, its symbolic dimension. The present study aims to investigate how meanings are created and negotiated through the abandonment of cigarettes. This study used a qualitative methodology to collect and analyze the data generated by one-on-one semi-structured in-depth interviews with 15 Brazilian ex-smokers. Results suggest that abandonment of cigarettes can be offered as a connection, gift, or sacrifice that makes relations special and even magical. As regards abandonment, the present study evidences the interactions and movements of positive and negative meanings related to the consumption and non-consumption of a category. The study proposes a framework that highlights the cooling, decontamination, reinforcement and defensive symbolical movements, thus constructing a tool for analyzing abandonment, offering possible paths of intervention for organizations that are interested in this issue.

Preliminary characterization of abandoned septic tank systems. Volume 1

International Nuclear Information System (INIS)

1995-12-01

This report documents the activities and findings of the Phase I Preliminary Characterization of Abandoned Septic Tank Systems. The purpose of the preliminary characterization activity was to investigate the Tiger Team abandoned septic systems (tanks and associated leachfields) for the purpose of identifying waste streams for closure at a later date. The work performed was not to fully characterize or remediate the sites. The abandoned systems potentially received wastes or effluent from buildings which could have discharged non-domestic, petroleum hydrocarbons, hazardous, radioactive and/or mixed wastes. A total of 20 sites were investigated for the preliminary characterization of identified abandoned septic systems. Of the 20 sites, 19 were located and characterized through samples collected from each tank(s) and, where applicable, associated leachfields. The abandoned septic tank systems are located in Areas 5, 12, 15, 25, and 26 on the Nevada Test Site

Inconsistent identification of pit bull-type dogs by shelter staff.

Science.gov (United States)

Olson, K R; Levy, J K; Norby, B; Crandall, M M; Broadhurst, J E; Jacks, S; Barton, R C; Zimmerman, M S

2015-11-01

Shelter staff and veterinarians routinely make subjective dog breed identification based on appearance, but their accuracy regarding pit bull-type breeds is unknown. The purpose of this study was to measure agreement among shelter staff in assigning pit bull-type breed designations to shelter dogs and to compare breed assignments with DNA breed signatures. In this prospective cross-sectional study, four staff members at each of four different shelters recorded their suspected breed(s) for 30 dogs; there was a total of 16 breed assessors and 120 dogs. The terms American pit bull terrier, American Staffordshire terrier, Staffordshire bull terrier, pit bull, and their mixes were included in the study definition of 'pit bull-type breeds.' Using visual identification only, the median inter-observer agreements and kappa values in pair-wise comparisons of each of the staff breed assignments for pit bull-type breed vs. not pit bull-type breed ranged from 76% to 83% and from 0.44 to 0.52 (moderate agreement), respectively. Whole blood was submitted to a commercial DNA testing laboratory for breed identification. Whereas DNA breed signatures identified only 25 dogs (21%) as pit bull-type, shelter staff collectively identified 62 (52%) dogs as pit bull-type. Agreement between visual and DNA-based breed assignments varied among individuals, with sensitivity for pit bull-type identification ranging from 33% to 75% and specificity ranging from 52% to 100%. The median kappa value for inter-observer agreement with DNA results at each shelter ranged from 0.1 to 0.48 (poor to moderate). Lack of consistency among shelter staff indicated that visual identification of pit bull-type dogs was unreliable. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Sustainable Environmental Protection Using Modified Pit-Latrines

NARCIS (Netherlands)

Chaggu, E.J.

2004-01-01

Pit-latrines are on-site excreta disposal facilities widely used as anaerobic accumulation system for stabilizing human wastes like excreta, both in rural and urban settlements of developing countries. Flooding of pit-latrines is often a common phenomenon, especially in situations of high water

Op-Ug TD Optimizer Tool Based on Matlab Code to Find Transition Depth From Open Pit to Block Caving / Narzędzie Optymalizacyjne Oparte O Kod Matlab Wykorzystane Do Określania Głębokości Przejściowej Od Wydobycia Odkrywkowego Do Wybierania Komorami

Science.gov (United States)

Bakhtavar, E.

2015-09-01

In this study, transition from open pit to block caving has been considered as a challenging problem. For this purpose, the linear integer programing code of Matlab was initially developed on the basis of the binary integer model proposed by Bakhtavar et al (2012). Then a program based on graphical user interface (GUI) was set up and named "Op-Ug TD Optimizer". It is a beneficial tool for simple application of the model in all situations where open pit is considered together with block caving method for mining an ore deposit. Finally, Op-Ug TD Optimizer has been explained step by step through solving the transition from open pit to block caving problem of a case ore deposit. W pracy tej rozważano skomplikowane zagadnienie przejścia od wybierania odkrywkowego do komorowego. W tym celu opracowano kod programowania liniowego w środowisku MATLAB w oparciu o model liczb binarnych zaproponowany przez Bakhtavara (2012). Następnie opracowano program z wykorzystujący graficzny interfejs użytkownika o nazwie Optymalizator Op-Ug TD. Jest to niezwykle cenne narzędzie umożliwiające stosowanie modelu dla wszystkich warunków w sytuacjach gdy rozważamy prowadzenie wydobycia metodą odkrywkową oraz wydobycie komorowe przy eksploatacji złóż rud żelaza. W końcowej części pracy podano szczegółową instrukcję stosowanie programu Optymalizator na przedstawionym przykładzie przejścia od wydobycia rud żelaza metodami odkrywkowymi poprzez wydobycie komorami.

A predictive approach to fitness-for-service assessment of pitting corrosion

International Nuclear Information System (INIS)

Shekari, Elahe; Khan, Faisal; Ahmed, Salim

2016-01-01

Pitting corrosion is a localized corrosion that often causes leak and failure of process components. The aim of this work is to present a new fitness-for-service (FFS) assessment methodology for process equipment to track and predict pitting corrosion. In this methodology, pit density is modeled using a non-homogenous Poisson process and induction time for pit initiation is simulated as the realization of a Weibull process. The non-homogenous Markov process is used to estimate maximum pit depth, considering that only the current state of the damage influences its future development. Subsequently, the distributions of the operating pressure and the estimated burst pressure of the defected component are integrated with Monte Carlo simulations and First Order Second Moment (FOSM) method to calculate the reliability index and probability of failure. This methodology provides a more realistic failure assessment and enables consideration of uncertainty associated with estimating pit characteristics. The practical application of the proposed model is demonstrated using a piping case study. - Highlights: • A new model to estimate maximum pit depth and pit density as two main pit characteristics. • Integrating maximum pit depth with failure analysis considering allowable pressure of defected component. • Time dependent failure analysis to determine the remaining life.

Bacterial community composition in the water column of a lake formed by a former uranium open pit mine.

Science.gov (United States)

Edberg, Frida; Andersson, Anders F; Holmström, Sara J M

2012-11-01

Mining of pyrite minerals is a major environmental issue involving both biological and geochemical processes. Here we present a study of an artificial lake of a former uranium open pit mine with the aim to connect the chemistry and bacterial community composition (454-pyrosequencing of 16S rRNA genes) in the stratified water column. A shift in the water chemistry from oxic conditions in the epilimnion to anoxic, alkaline, and metal and sulfide-rich conditions in the hypolimnion was corresponded by a strong shift in the bacterial community, with few shared operational taxonomic units (OTU) between the water layers. The epilimnetic bacterial community of the lake (~20 years old) showed similarities to other temperate freshwater lakes, while the hypolimnetic bacterial community showed similarity to extreme chemical environments. The epilimnetic bacterial community had dominance of Actinobacteria and Betaproteobacteria. The hypolimnion displayed a higher bacterial diversity and was dominated by the phototrophic green sulphur bacterium of the genus Chlorobium (ca. 40 % of the total community). Deltaproteobacteria were only represented in the hypolimnion and the most abundant OTUs were affiliated with ferric iron and sulfate reducers of the genus Geobacter and Desulfobulbus, respectively. The chemistry is clearly controlling, especially the hypolimnetic, bacterial community but the community composition also indicates that the bacteria are involved in metal cycling in the lake.

Least tern and piping plover nesting at sand pits in Nebraska

Science.gov (United States)

Sidle, John G.; Kirsch, E.M.

1993-01-01

Endangered Least Terns (Sterna antillarum) and threatened Piping Plovers (Charadrius melodus) nest at commercial sand and gravel mining operations (sand pits) along the Platte River system in Nebraska. Sandbar habitat has been disappearing since the early 1900's along the Platte River system, but numbers of sand pits have increased. We hypothesized that birds would more fully utilize sand pits where suitable sandbar habitat was limited. We inventoried sand pits and censused terns and plovers on both habitats along the Loup River, part of the North Loup River, and most of the Platte River during 1988-1991. Using aircraft, we also quantified features of suitable sand pits present on the central Platte in 1988 and lower Platte in 1990, and related features to abundance and presence of birds. We found 225 sand pits of which 78 were suitable and 187 were unsuitable for nesting. Along the central Platte, where sandbar habitat is severely degraded, birds nested at 81% of the suitable sand pits (N = 32) at least once during 1988-1991, and most birds (61-94%) nested on sand pits. Along the lower Platte, where both sandbar and sand pit habitat are plentiful, birds nested at 60% of the suitable sand pits (N = 35) at least once during 1988-1991, and most birds (60-86%) nested on sandbars. Numbers of terns and plovers were more weakly correlated with features of sand pits on the central Platte than on the lower Platte. Least Terns and Piping Plovers seem to use more of the suitable sand pit habitat on the central Platte than on the lower Platte. Sand pits probably have influenced the birds' distribution by providing alternative nesting habitat along rivers where suitable sandbars are rare or absent.

Composição mineral e severidade de "bitter pit" em maçãs 'Catarina' Mineral composition and bitter pit severity in 'Catarina' apples

Directory of Open Access Journals (Sweden)

Cassandro Vidal Talamini do Amarante

2006-04-01

Full Text Available Maçãs 'Catarina', colhidas na maturação comercial em pomar no município de São Joaquim-SC, foram separadas em quatro lotes de 14 frutos, de acordo com a severidade de incidência de "bitter pit": nula (nenhuma lesão/fruto, baixa (1-2 lesões/fruto, moderada (3-5 lesões/fruto e alta (6-18 lesões/fruto. Foram determinadas as concentrações de Ca, Mg, K e N na casca e na polpa de cada fruto. Foram verificadas relação linear (P 'Catarina' apples were harvested at the commercial maturity in an orchard in São Joaquim-SC and segregated in four lots of 14 fruits with different levels of bitter pit severity: null (none pit/fruit, low (1-2 pits/fruit, moderate (3-5 pits/fruit, and high (6-18 pits/fruit. Nutritional analysis (Ca, Mg, K, and N in the skin and flesh tissues were performed on individual fruits of each severity level. The average number of pits/fruit (calculated for each lot of bitter pit severity showed a negative linear relationship (P < 0.05 with the skin Ca content, and a negative linear relationship (P < 0.05 with the ratios of Mg/Ca, (K+Mg/Ca, and (K+Mg+N/Ca in the skin. For the flesh, the increasing of bitter pit severity was accompanied by significant reduction of Ca and Mg contents. The multivariate analysis (canonical discriminant analysis showed that the Mg/Ca ratio in the skin provided the best discrimination between the lots of fruit with different levels of bitter pit severity. Therefore, for 'Catarina' apples, increasing values of the Mg/Ca ratio in the skin are indicative of fruits with increasing bitter pit susceptibility.

Seventeen Years of Delivery of Open and Distance Education by ...

African Journals Online (AJOL)

Seventeen Years of Delivery of Open and Distance Education by The Open University of Tanzania (OUT) in East Africa and Beyond. ... This has necessitated the abandonment of the old annual confidential review forms used by most east African universities. The paper ends by highlighting the main prospects and ...

Deterministic chaos in the pitting phenomena of passivable alloys

International Nuclear Information System (INIS)

Hoerle, Stephane

1998-01-01

It was shown that electrochemical noise recorded in stable pitting conditions exhibits deterministic (even chaotic) features. The occurrence of deterministic behaviors depend on the material/solution severity. Thus, electrolyte composition ([Cl - ]/[NO 3 - ] ratio, pH), passive film thickness or alloy composition can change the deterministic features. Only one pit is sufficient to observe deterministic behaviors. The electrochemical noise signals are non-stationary, which is a hint of a change with time in the pit behavior (propagation speed or mean). Modifications of electrolyte composition reveals transitions between random and deterministic behaviors. Spontaneous transitions between deterministic behaviors of different features (bifurcation) are also evidenced. Such bifurcations enlighten various routes to chaos. The routes to chaos and the features of chaotic signals allow to suggest the modeling (continuous and discontinuous models are proposed) of the electrochemical mechanisms inside a pit, that describe quite well the experimental behaviors and the effect of the various parameters. The analysis of the chaotic behaviors of a pit leads to a better understanding of propagation mechanisms and give tools for pit monitoring. (author) [fr

41 CFR 109-45.901 - Authority to abandon or destroy.

Science.gov (United States)

2010-07-01

... AND DISPOSAL 45-SALE, ABANDONMENT, OR DESTRUCTION OF PERSONAL PROPERTY 45.9-Abandonment or Destruction of Personal Property § 109-45.901 Authority to abandon or destroy. Personal property in the... determination has been made by the OPMO that property has no commercial value or the estimated cost of its...

Environmental Effects of Abandoned Properties in Ogbomoso and ...

African Journals Online (AJOL)

... reptiles, accident and vagrancy. The brunt of abandonment is found to be more in the medium residential density. The study thus recommends an aggressive environmental management that offsets blighted conditions in the environment. Keywords: Effects, Buildings, Lots, Abandonment, Landed Properties, Environment ...

The post-mining context at Decazeville-Firmi concession (Aveyron, France): analysis of impacts resulting from the cessation of pumping at the central shaft. Survey of various scenarios related to the water level of the pit lake in the Grande Decouverte

International Nuclear Information System (INIS)

Cojean, R.; Franco, N.; Lazarewicz, J.C.; Blachere, A.; Lefort, D.; Sorgi, C.

2005-01-01

Within the frame of the Survey related to the cessation of mine workings in Decazeville-Firmi concession, various impacts resulting from the cessation of pumping at the Central Shaft were assessed. Mainly these impacts are related to groundwater behaviour in the abandoned underground coal mines, hydro-chemistry of waters discharged to the environment, ground stability concerns and coal gas emanations. This analysis allowed the choice of the most appropriate elevation of the pit lake level in the Grande Decouverte, with the necessity to continue the pumping. Two main objectives were reached. The elected elevation is high enough to result in a permanent chemical stratification, which allows the pumping of the superficial waters and its discharge to natural watercourses without any treatment. The elected elevation is low enough to avoid any problem of inflow of water or ground stability at some particular places which might have been threatened by the rising of the piezometric level of the mining aquifer. Lastly, the elected elevation of the pit lake allows a quality scenery design around the pit lake. (authors)

The post-mining context at Decazeville-Firmi concession (Aveyron, France): analysis of impacts resulting from the cessation of pumping at the central shaft. Survey of various scenarios related to the water level of the pit lake in the Grande Decouverte

Energy Technology Data Exchange (ETDEWEB)

Cojean, R. [Ecole des Mines de Paris, Institut des Geosciences, Centre de Geologie de l' Ingenieur, UMLV, 77 - Marne-la-Vallee (France); Franco, N. [Charbonnages de France, Dir. Technique Nationale, 42 - Saint-Etienne (France); Lazarewicz, J.C. [Charbonnages de France, Dir. Technique Nationale, 13 - Meyreuil (France); Blachere, A.; Lefort, D. [Bureau d' Etudes CESAME, 42 - Fraisses (France); Sorgi, C. [INERIS, 60 - Verneuil-en-Halatte (France)

2005-07-01

Within the frame of the Survey related to the cessation of mine workings in Decazeville-Firmi concession, various impacts resulting from the cessation of pumping at the Central Shaft were assessed. Mainly these impacts are related to groundwater behaviour in the abandoned underground coal mines, hydro-chemistry of waters discharged to the environment, ground stability concerns and coal gas emanations. This analysis allowed the choice of the most appropriate elevation of the pit lake level in the Grande Decouverte, with the necessity to continue the pumping. Two main objectives were reached. The elected elevation is high enough to result in a permanent chemical stratification, which allows the pumping of the superficial waters and its discharge to natural watercourses without any treatment. The elected elevation is low enough to avoid any problem of inflow of water or ground stability at some particular places which might have been threatened by the rising of the piezometric level of the mining aquifer. Lastly, the elected elevation of the pit lake allows a quality scenery design around the pit lake. (authors)

Abandoned floodplain plant communities along a regulated dryland river

Science.gov (United States)

Reynolds, L. V.; Shafroth, Patrick B.; House, P. K.

2014-01-01

Rivers and their floodplains worldwide have changed dramatically over the last century because of regulation by dams, flow diversions and channel stabilization. Floodplains no longer inundated by river flows following dam-induced flood reduction comprise large areas of bottomland habitat, but the effects of abandonment on plant communities are not well understood. Using a hydraulic flow model, geomorphic mapping and field surveys, we addressed the following questions along the Bill Williams River, Arizona: (i) What per cent of the bottomland do abandoned floodplains comprise? and (ii) Are abandoned floodplains quantitatively different from adjacent xeric and riparian surfaces in terms of vegetation composition and surface sediment? We found that nearly 70% of active channel and floodplain area was abandoned following dam installation. Abandoned floodplains along the Bill Williams River tend to be similar to each other yet distinct from neighbouring habitats: they have been altered physically from their historic state, leading to distinct combinations of surface sediments, hydrology and plant communities. Abandoned floodplains may transition to xeric communities over time but are likely to retain some riparian qualities as long as there is access to relatively shallow ground water. With expected increases in water demand and drying climatic conditions in many regions, these surfaces and associated vegetation will continue to be extensive in riparian landscapes worldwide

Phosphate ions as inhibiting agents for copper corrosion in chlorinated tap water

International Nuclear Information System (INIS)

Yohai, L.; Schreiner, W.H.; Vázquez, M.; Valcarce, M.B.

2013-01-01

PO 4 3− ions as corrosion inhibitor were investigated on copper in tap water in the presence of NaClO. The inhibitor was evaluated by electrochemical techniques and weight loss tests. Raman spectroscopy and X-ray photoelectron spectroscopy were used to study the passive layer. In inhibited tap water, the passive layer is thick and compact if NaClO is present. Weight-loss tests showed the inhibition of uniform dissolution and no pitting attack. When adding NaClO, Cu 3 (PO 4 ) 2 is incorporated to the passive film. Thus, phosphate ions are effective as inhibitors for copper in tap water, even when using high dosages of biocides. - Highlights: ► Changes in the copper corrosion after adding phosphate to tap water were analyzed. ► When NaClO and phosphates are present, Cu 3 (PO 4 ) 2 participates of the surface film. ► In the absence of biocide the surface film contains a mixture of Cu 2 O, CuO and Cu(OH) 2 . ► PO 4 3− is an effective inhibitor for Cu in tap water containing high NaClO dosages

Spontaneous Resolution of Optic Disc Pit Maculopathy

Directory of Open Access Journals (Sweden)

Koushik Tripathy

2017-06-01

Full Text Available I read with interest the article reporting spontaneous resolution of optic disc pit maculopathy in a boy.1 Though the presence of an optic disc pit and associated macular involvement is undoubted in the presented case, the provided optical coherence tomography (OCT does not clearly show typical intraretinal schisis (Figure 1B1 at multiple retinal levels which may communicate with the pit. Instead, it shows a sub-internal limiting membrane (sub-ILM cavity. Such cavities are known to occur following the resolution of sub-ILM bleed due to various cause including Valsalva retinopathy,2 Terson syndrome, and also in some retinitis3 cases.4 In fact, some of these cavities may simulate a neurosensory retinal detachment or central serous chorioretinopathy on cursory clinical examination.5 To confirm that the features of the current patient1 are indeed related to the optic disc pit, it is necessary for the authors to provide an OCT scan which shows a connection of the presented cavity with the optic disc pit. Also, clear OCT scans of the fovea, both at presentation and at final follow-up would help our understanding of the visual recovery of the patient. The interval between the presenting (28 June 2012 OCT and final OCT (30 Nov 2012 is 5 months and not 6 months as described in the manuscript. For an effective comparison, both the presenting and final OCT scans should have been taken using either horizontal or vertical orientation over the macula. Though the spontaneous resolution of optic disc pit maculopathy is possible, visual recovery in usually unlikely and in such cases an alternate diagnosis needs to be excluded.

Liquid waste processing from TRIGA spent fuel storage pits

International Nuclear Information System (INIS)

Buchtela, Karl

1988-01-01

At the Atominstitute of the Austrian Universities and also at other facilities running TRIGA reactors, storage pits for spent fuel elements are installed. During the last revision procedure, the reactor group of the Atominstitute decided to refill the storage pits and to get rid of any contaminated storage pit water. The liquid radioactive waste had been pumped to polyethylene vessels for intermediate storage before decontamination and release. The activity concentration of the storage pit water at the Aominstitute after a storage period of several years was about 40 kBq/l, the total amount of liquid in the storage pits was about 0.25 m 3 . It was attempted to find a simple and inexpensive method to remove especially the radioactive Cesium from the waste solution. Different methods for decontamination like distillation, precipitation and ion exchange are discussed

Investigation of Stress Concentration and Casing Strength Degradation Caused by Corrosion Pits

Directory of Open Access Journals (Sweden)

Wei Yan

2016-01-01

Full Text Available Downhole casing and tubing are subjected to corrosion in many cases because of the exposure to corrosive environment. A more serious problem is that pitting corrosion occurs in the casing inner surface. Meanwhile, downhole strings are subjected to various forms of mechanical loads, for example, internal pressure load, external collapse load, or both. These loads acting on the corrosion pits will cause stress concentration and degrade the casing strength. Thus, it is essential to evaluate the stress concentration degree reasonably. The SCF (stress concentration factor is usually used to characterize the degree of stress concentration induced by corrosion pits. This paper presented a comparison on the SCFs regarding the analytical method for a single pit and experimental method for double pits. The results show that the SCF of a single pit depends mainly on the depth of the corrosion pit; however, the SCF of the double pits strongly depends on the pits distance. A correction factor of 1.3 was recommended in the double pits SCF prediction model.

Applying persistent scatterer interferometry for surface displacement mapping in the Azul open pit manganese mine (Amazon region) with TerraSAR-X StripMap data

Science.gov (United States)

Athayde Pinto, Carolina de; Paradella, Waldir Renato; Mura, José Claudio; Gama, Fabio Furlan; Ribeiro dos Santos, Athos; Silva, Guilherme Gregório; Hartwig, Marcos Eduardo

2015-01-01

The Azul mining complex, located in the Carajás Mineral Province, Amazon region, encompasses the most important manganese mine in Brazil. Vale S.A. company operates three simultaneous open pit excavations (mines 1, 2, and 3) in the area, which are conducted on rock alteration products of low geomechanical quality related to sandstones, siltstones, and a lateritic cover. In order to monitor ground deformation, 33 TerraSAR-X (TSX-1) StripMap images covering the period of March 2012-April 2013 were used in the investigation. An advanced differential interferometric synthetic aperture radar (A-DInSAR) approach based on persistent scatterer interferometry (PSI) using an interferometric point target analysis algorithm was applied, and the results showed that most of the area was considered stable during the time span of the synthetic aperture radar acquisitions. However, persistent scatterers (PS) with high deformation rates were mapped over a waste pile, probably related to settlements, and also along the north flank of mine 1, indicative of cut slope movements toward the center of the pit. A spatial relationship of geological structures with PS was observed for this sector of the mine, given by PS showing deformation rates concentrated along a structural corridor with faults, fractures, and folds related to the Carajás fault system. Though only ground-based radar measurements for wall benches of mine 1 were available for a short time period of the TSX-1 coverage, the PS movement patterns showed concordance with geotechnical field measurements. The investigation emphasized the important role that satellite-based A-DInSAR can play for deformation monitoring and risk assessment in this kind of mining area.

Speed, Acceleration, Chameleons and Cherry Pit Projectiles

Science.gov (United States)

Planinsic, Gorazd; Likar, Andrej

2012-01-01

The paper describes the mechanics of cherry pit projectiles and ends with showing the similarity between cherry pit launching and chameleon tongue projecting mechanisms. The whole story is written as an investigation, following steps that resemble those typically taken by scientists and can therefore serve as an illustration of scientific…

Fabrication of free-standing copper foils covered with highly-ordered copper nanowire arrays

Science.gov (United States)

Zaraska, Leszek; Sulka, Grzegorz D.; Jaskuła, Marian

2012-07-01

The through-hole nanoporous anodic aluminum oxide (AAO) membranes with relatively large surface area (ca. 2 cm2) were employed for fabrication of free-standing and mechanically stable copper foils covered with close-packed and highly-ordered copper nanowire arrays. The home-made AAO membranes with different pore diameters and interpore distances were fabricated via a two-step self-organized anodization of aluminum performed in sulfuric acid, oxalic acid and phosphoric acid followed by the pore opening/widening procedure. The direct current (DC) electrodeposition of copper was performed efficiently on both sides of AAO templates. The bottom side of the AAO templates was not insulated and consequently Cu nanowire arrays on thick Cu layers were obtained. The proposed template-assisted fabrication of free-standing copper nanowire array electrodes is a promising method for synthesis of nanostructured current collectors. The composition of Cu nanowires was confirmed by energy dispersive X-Ray spectroscopy (EDS) and X-ray diffraction (XRD) analyses. The structural features of nanowires were evaluated from field emission scanning electron microscopy (FE-SEM) images and compared with the characteristic parameters of anodic alumina membranes.

Fabrication of free-standing copper foils covered with highly-ordered copper nanowire arrays

International Nuclear Information System (INIS)

Zaraska, Leszek; Sulka, Grzegorz D.; Jaskuła, Marian

2012-01-01

The through-hole nanoporous anodic aluminum oxide (AAO) membranes with relatively large surface area (ca. 2 cm 2 ) were employed for fabrication of free-standing and mechanically stable copper foils covered with close-packed and highly-ordered copper nanowire arrays. The home-made AAO membranes with different pore diameters and interpore distances were fabricated via a two-step self-organized anodization of aluminum performed in sulfuric acid, oxalic acid and phosphoric acid followed by the pore opening/widening procedure. The direct current (DC) electrodeposition of copper was performed efficiently on both sides of AAO templates. The bottom side of the AAO templates was not insulated and consequently Cu nanowire arrays on thick Cu layers were obtained. The proposed template-assisted fabrication of free-standing copper nanowire array electrodes is a promising method for synthesis of nanostructured current collectors. The composition of Cu nanowires was confirmed by energy dispersive X-Ray spectroscopy (EDS) and X-ray diffraction (XRD) analyses. The structural features of nanowires were evaluated from field emission scanning electron microscopy (FE-SEM) images and compared with the characteristic parameters of anodic alumina membranes.

Mechanical characterization of hybrid and functionally-graded aluminum open-cell foams with nanocrystalline-copper coatings

Science.gov (United States)

Sun, Yi

absorption capacity. The behavior of Al/Cu hybrid foams under high-strain-rate condition was then investigated using experiments on a split Hopkinson pressure bar. It was found that the ED nano-copper coating can also effectively enhance the energy absorption capacities of aluminum open-cell foams under high strain rate. Similar to the quasi-static behavior, a large stress drop was observed in the compressive response of Al/Cu hybrid foams under high strain rate, which was accompanied by dramatic shattering of material. It is shown that a more ductile behavior and better energy absorption performance under high strain rate condition can be also obtained by introducing an annealing process. Finally, the manufacturing process of Al/Cu hybrid foams was customized to fabricate FGHMF systems with two dimensional property gradients. The performance of these FGHMFs at both quasi-static and dynamic conditions was evaluated. Under quasi-static condition, two flexural type loading conditions were considered, namely, a three point bending condition and a cantilever beam condition. The dynamic behavior of FGHMFs was investigated by conducting drop weight tower tests on a three point bending setup. It was found that the failure mechanism of hybrid metal foams can be modified and the mechanical properties, such as stiffness and strength, and energy absorption capacities of hybrid metal foams can be optimized under both quasi-static and dynamic conditions by introducing strategically designed coating patterns. The presented novel approach and findings in this study provide valuable information on the development of high performance hybrid and functionally-graded cellular materials.

Electrochemical analysis of the corrosion inhibition effect of trypsin complex on the pitting corrosion of 420 martensitic stainless steel in 2M H2SO4 solution.

Science.gov (United States)

Loto, Roland Tolulope

2018-01-01

Inhibition effect of trypsin complex (TC) on the pitting corrosion of martensitic stainless steel (type 420) in 1M H2SO4 solution was studied with potentiodynamic polarization, open circuit potential measurement and optical microscopy. TC reduced the corrosion rate of the steel with maximum inhibition efficiency of 80.75%. Corrosion potential shifted anodically due to the electrochemical action of TC. The pitting potential increased from 1.088VAg/AgCl (3M) at 0% TC to 1.365VAg/AgCl(3M) at 4% TC. TC shifts the open circuit corrosion potential from -0.270s at 0% TC concentration to -0.255V at 5% TC. The compound completely adsorbed onto the steel according to Langmuir, Frumkin and Temkin isotherms. ATF-FTIR spectroscopy confirmed the inhibition mode to be through surface coverage. Thermodynamic calculations showed physisorption molecular interaction. Corrosion pits are present on the uninhibited 420 morphology in comparison to TC inhibited surface which slightly deteriorated.

Status of the pit disassembly and conversion facility

International Nuclear Information System (INIS)

Wood, Warren T.; Christensen, Lowell T.

2000-01-01

A planned new facility, the Pit Disassembly and Conversion Facility (PDCF), will be used to disassemble the nation's inventory of surplus nuclear weapons pits and convert the plutonium from those pits into a form suitable for storage, international inspection, and final disposition. Sized to handle 35 metric tons of plutonium from pits and other sources over its 10-year operating life, the PDCF will apply the Advanced Recovery and Integrated Extraction System (ARIES) technology. ARIES process technology has been developed at Los Alamos National Laboratory (LANL) and Lawrence Livermore National Laboratory (LLNL), and an integrated system is being demonstrated at LANL. The Los Alamos National Laboratory is the lead for technical design oversight of the PDCF. Technical data gained from the ARIES demonstrations is integral for the proper design of the PDCF

Best practices for the abandonment of pipelines

Energy Technology Data Exchange (ETDEWEB)

Mackean, M; Reed, R; Snow, B [Nabors Canada, Calgary, AB (Canada). Abandonrite Service

2006-07-01

Pipeline regulations implemented in 2006 require that licensees register all pipelines. Training must also be provided for ground disturbance supervisors. In addition, signage must be maintained on abandoned pipelines, and discontinued pipelines must be properly isolated. Corrosion control and internal inhibition is required for discontinued lines. However, pipelines are often neglected during the well abandonment process. This presentation provided recommendations for coordinating well and pipeline abandonment processes. Pipeline ends can be located, depressurized, flushed and purged while wells are being abandoned. Contaminated soils around the wells can also be identified prior to reclamation activities. Administrative reviews must be conducted in order to provide accurate information on pipeline location, reclamation certification, and line break history. Field operation files must be reviewed before preliminary field work is conducted. Site inspections should be used to determine if all ends of the line are accessible. Landowners and occupants near the line must also be notified, and relevant documentation must be obtained. Skilled technicians must be used to assess the lines for obstructions as well as to cut and cap the lines after removing risers. The presentation also examined issues related to pressure change, movement, cold tapping, and live dead legs. tabs., figs.

Corrosion behavior and pitting susceptibility of in-situ Ti-based metallic glass matrix composites in 3.5 wt.% NaCl solutions

Science.gov (United States)

Xu, K. K.; Lan, A. D.; Yang, H. J.; Han, P. D.; Qiao, J. W.

2017-11-01

The Ti62Zr12V13Cu4Be9, Ti58Zr16V10Cu4Be12, Ti46Zr20V12Cu5Be17, and Ti40Zr24V12Cu5Be19 metallic glass matrix composites (MGMCs) were prepared by copper mould casting. The corrosion resistance and the pitting susceptibility of Ti-based MGMCs were tested on their cross-sectional areas in 3.5 wt.% NaCl solutions by potentiodynamic polarization measurements. The composites with lower Ti contents (Ti40Zr24V12Cu5Be19 and Ti46Zr20V12Cu5Be17) exhibit a low resistance to the chloride induced pitting and local corrosion. The preferential dissolution of amorphous matrix is explained by the high chemical reactivity of beryllium element compared to that of stable dendrites and by the detected lower Ti and V contents. However, fairly good passivity was found in the composite with higher Ti contents (Ti62Zr12V13Cu4Be9). XPS measurements revealed that protective Ti-enriched oxide film was formed on the composite surface, additionally, lower content of beryllium element in amorphous matrix hinder the selective corrosion of amorphous matrix. The assessment of experimental observation leads to a proposed corrosion mechanism involving selective dissolution of amorphous matrix and chloride induced pitting process.

The role of inclusions in the pitting behaviour of maraging steel

International Nuclear Information System (INIS)

Ahmad, M.S.; Hussain, S.W.; Ashraf, H.

1999-01-01

The pitting characteristics of maraging steel in artificial seawater have been investigated electrochemically using the cyclic polarization technique. Pits were found to be associated with the inclusions present in steel. The hysteresis loop observed indicates that maraging steel has poor resistance to pitting in air saturated seawater. On examination of corroded surfaces under SEM, it is noted that the pits are always associated with inclusions, which are generally the carbonitrides of TiMo presents in maraging steel in varying quantities depending on the melting practice. In order to confirm that the pitting behavior is associated with inclusions, samples from clean maraging steel, having very low inclusion level, were tested. Such samples showed much less tendency for pitting. (author)

Survey of nine surface mines in North America. [Nine different mines in USA and Canada

Energy Technology Data Exchange (ETDEWEB)

Hayes, L.G.; Brackett, R.D.; Floyd, F.D.

1981-01-01

This report presents the information gathered by three mining engineers in a 1980 survey of nine surface mines in the United States and Canada. The mines visited included seven coal mines, one copper mine, and one tar sands mine selected as representative of present state of the art in open pit, strip, and terrace pit mining. The purpose of the survey was to investigate mining methods, equipment requirements, operating costs, reclamation procedures and costs, and other aspects of current surface mining practices in order to acquire basic data for a study comparing conventional and terrace pit mining methods, particularly in deeper overburdens. The survey was conducted as part of a project under DOE Contract No. DE-AC01-79ET10023 titled The Development of Optimal Terrace Pit Coal Mining Systems.

Force-displacement measurements of earlywood bordered pits using a mesomechanical tester

Science.gov (United States)

Samuel L. Zelinka; Keith J. Bourne; John C. Hermanson; Samuel V. Glass; Adriana Costa; Alex C. Wiedenhoeft

2015-01-01

The elastic properties of pit membranes are reported to have important implications in understanding air-seeding phenomena in gymnosperms, and pit aspiration plays a large role in wood technological applications such as wood drying and preservative treatment. Here we present force–displacement measurements for pit membranes of circular bordered pits, collected on a...

Investigating oiled birds from oil field waste pits

International Nuclear Information System (INIS)

Gregory, D.G.; Edwards, W.C.

1991-01-01

Procedures and results of investigations concerning the oiling of inland raptors, migratory water-fowl and other birds are presented. Freon washings from the oiled birds and oil from the pits were analyzed by gas chromatography. In most instances the source of the oil could be established by chromatographic procedures. The numbers of birds involved (including many on the endangered species list) suggested the need for netting or closing oil field waste pits and mud disposal pits. Maintaining a proper chain of custody was important

Water and chemical budgets of gravel pit lakes : Case studies of fluvial gravel pit lakes along the Meuse River (The Netherlands) and coastal gravel pit lakes along the Adriatic Sea (Ravenna, Italy)

NARCIS (Netherlands)

Mollema, P.N.

2016-01-01

Gravel pit lakes form when gravel is excavated from below the water table of a phreatic or shallow confined aquifer. Typically many of these lakes are concentrated along naturally occurring sedimentary gravel deposits in areas where gravel is needed for construction. Most gravel pit lakes are

Bonding and structure of copper nitrenes.

Science.gov (United States)

Cundari, Thomas R; Dinescu, Adriana; Kazi, Abul B

2008-11-03

Copper nitrenes are of interest as intermediates in the catalytic aziridination of olefins and the amination of C-H bonds. However, despite advances in the isolation and study of late-transition-metal multiply bonded complexes, a bona fide structurally characterized example of a terminal copper nitrene has, to our knowledge, not been reported. In anticipation of such a report, terminal copper nitrenes are studied from a computational perspective. The nitrene complexes studied here are of the form (beta-diketiminate)Cu(NPh). Density functional theory (DFT), complete active space self-consistent-field (CASSCF) electronic structure techniques, and hybrid quantum mechanical/molecular mechanical (QM/MM) methods are employed to study such species. While DFT methods indicate that a triplet (S = 1) is the ground state, CASSCF calculations indicate that a singlet (S = 0) is the ground state, with only a small energy gap between the singlet and triplet. Moreover, the ground-state (open-shell) singlet copper nitrene is found to be highly multiconfigurational (i.e., biradical) and to possess a bent geometry about the nitrene nitrogen, contrasting with the linear nitrene geometry of the triplet copper nitrenes. CASSCF calculations also reveal the existence of a closed-shell singlet state with some degree of multiple bonding character for the copper-nitrene bond.

Localized Detection of Abandoned Luggage

Directory of Open Access Journals (Sweden)

Jing-Ying Chang

2010-01-01

Full Text Available Abandoned luggage represents a potential threat to public safety. Identifying objects as luggage, identifying the owners of such objects, and identifying whether owners have left luggage behind are the three main problems requiring solution. This paper proposes two techniques which are “foreground-mask sampling” to detect luggage with arbitrary appearance and “selective tracking” to locate and to track owners based solely on looking only at the neighborhood of the luggage. Experimental results demonstrate that once an owner abandons luggage and leaves the scene, the alarm fires within few seconds. The average processing speed of the approach is 17.37 frames per second, which is sufficient for real world applications.

Stochastic models for predicting pitting corrosion damage of HLRW containers

International Nuclear Information System (INIS)

Henshall, G.A.

1991-10-01

Stochastic models for predicting aqueous pitting corrosion damage of high-level radioactive-waste containers are described. These models could be used to predict the time required for the first pit to penetrate a container and the increase in the number of breaches at later times, both of which would be useful in the repository system performance analysis. Monte Carlo implementations of the stochastic models are described, and predictions of induction time, survival probability and pit depth distributions are presented. These results suggest that the pit nucleation probability decreases with exposure time and that pit growth may be a stochastic process. The advantages and disadvantages of the stochastic approach, methods for modeling the effects of environment, and plans for future work are discussed

A Bayesian approach to modeling and predicting pitting flaws in steam generator tubes

International Nuclear Information System (INIS)

Yuan, X.-X.; Mao, D.; Pandey, M.D.

2009-01-01

Steam generators in nuclear power plants have experienced varying degrees of under-deposit pitting corrosion. A probabilistic model to accurately predict pitting damage is necessary for effective life-cycle management of steam generators. This paper presents an advanced probabilistic model of pitting corrosion characterizing the inherent randomness of the pitting process and measurement uncertainties of the in-service inspection (ISI) data obtained from eddy current (EC) inspections. A Markov chain Monte Carlo simulation-based Bayesian method, enhanced by a data augmentation technique, is developed for estimating the model parameters. The proposed model is able to predict the actual pit number, the actual pit depth as well as the maximum pit depth, which is the main interest of the pitting corrosion model. The study also reveals the significance of inspection uncertainties in the modeling of pitting flaws using the ISI data: Without considering the probability-of-detection issues and measurement errors, the leakage risk resulted from the pitting corrosion would be under-estimated, despite the fact that the actual pit depth would usually be over-estimated.

Investigation of impingement attack mechanism of copper alloy condenser tubes

Energy Technology Data Exchange (ETDEWEB)

Fukumura, Takuya; Nakajima, Nobuo; Arioka, Koji; Totsuka, Nobuo; Nakagawa, Tomokazu [Institute of Nuclear Safety System Inc., Mihama, Fukui (Japan)

2001-09-01

In order to investigate generation and growth mechanisms of impingement attacks of sea water against copper alloy condenser tubes used in condensers of nuclear power plants, we took out condenser tubes from actual condensers, cut them into several pieces and carried out several material tests mainly for impinged spots. In addition water flow inside of a pit was analyzed. From the results of the investigation, it was found that all of impingement attacks were found in the marks left by sessile organisms and none were found in downstream of the marks as frequently proposed so far. At the pits generated inside the marks, iron coating was striped and zinc content was deficient in some cases. Combining these data and the result of flow analysis, we considered the following mechanism of the impingement attacks: sessile organisms clinging to the surface of the condenser tube and growth, occlusion of the tube, extinction and decomposition of sessile organisms, pollution corrosion under the organisms and cavity formation, occlusion removal by the cleaning, generation of impingement attacks by flow collision inside the cavity, growth of the impingement attacks. (author)

Tale of two pit lakes: initial results of a three-year study of the Main Zone and Waterline pit lakes near Houston, British Columbia, Canada

Science.gov (United States)

Crusius, John; Pieters, R.; Leung, A.; Whittle, P.; Pedersen, T.; Lawrence, G.; McNee, J.J.

2003-01-01

Pit lakes are becoming increasingly common in North America as well as in the rest of the world. They are created as openpit mines fill passively with ground water and surface inflows on cessation of mining activity. In many instances, the water quality in these pit lakes does not meet regulatory requirements due to a number of influences. The most important are the oxidation of sulfide minerals and the associated release of acid and metals and the flushing of soluble metals during pit filling. Examples of pit lakes with severe water-quality problems include the Berkeley Pit lake (Butte, MT) and the Liberty Pit lake (Nevada), whose waters are characterized by a pH near 3 and Cu concentrations as high as ~150 mg/L (Miller et al., 1996; Davis and Eary, 1997). The importance of the problem can be seen in the fact that some of these sites in the United States are Superfund sites.

Pipeline abandonment - a discussion paper on technical and environmental issues

International Nuclear Information System (INIS)

1996-11-01

The technical and environmental issues associated with pipeline abandonment were reviewed to provide a basis for the development of guidelines that companies could follow in order to abandon oil and gas pipelines in an environmentally safe and economic manner. Some of the topics discussed include land use management, ground subsidence, soil and groundwater contamination, erosion and the potential to create water conduits. A major issue still to be resolved, i.e., the legal and financial aspects of pipeline abandonment, was addressed. An industry-financed fund has been created to cover the cost of reclamation and abandonment of orphaned pipelines and certain associated pipeline facilities. 30 refs., 4 tabs., 3 figs

Geochemical atlas of Radovish and the environs and the distribution of heavy metals in the air

International Nuclear Information System (INIS)

Stafilov, Trajche; Bacheva, Katerina; Boev, Blazho; Shajn, Robert; Balabanova, Biljana

2010-01-01

Mining activities, ore processing and processing of waste are potential emitters of heavy metals in air. As more important are mining activities on surface excavation of ore due to the large number of direct polluting factors that are difficult to control and manage. Special emphasis is given to the organization of the pit (road movement of dampers carrying ore waste), waste management (ore and flotation tailings) as well as the frequency of explosions for excavation of mining minerals. One of the major emission sources of some metals in the eastern part of the R. Macedonia is Buchim copper mine and flotation, near the town of Radovish. The mine and plant for the preparation of ore are in function from the late seventies of the last century. Ore excavation is from open pit and the ore tailings are stored in the open, in mine vicinity. The produced copper ore from the mine is processed in the flotation tailings are separated, disposed of and deposited on a dump site in an adjacent valley near the village Topolnica.

Fish assemblages in borrow-pit lakes of the Lower Mississippi River

Science.gov (United States)

Miranda, Leandro E.; Killgore, K. J.; Hoover, J.J.

2013-01-01

Borrow-pit lakes encompass about a third of the lentic water habitats (by area) in the active floodplain of the Lower Mississippi River, yet little is known about their fish assemblages. We investigated whether fish assemblages supported by borrow-pit lakes resembled those in oxbow lakes to help place the ecological relevance of borrow-pit lakes in context with that of natural floodplain lakes. In all, we collected 75 fish species, including 65 species in eight borrow-pit lakes, 52 species in four riverside oxbow lakes, and 44 species in eight landside oxbow lakes. Significant differences in several species richness metrics were evident between borrow-pit lakes and landside oxbow lakes but not between borrow-pit lakes and riverside oxbow lakes. All three lake types differed in fish assemblage composition. Borrow-pit lakes and riverside oxbow lakes tended to include a greater representation of fish species that require access to diverse environments, including lentic, lotic, and palustrine habitats; fish assemblages in landside oxbow lakes included a higher representation of lacustrine species. None of the fish species collected in borrow-pit lakes was federally listed as threatened or endangered, but several were listed as species of special concern by state governments in the region, suggesting that borrow-pit lakes provide habitat for sensitive riverine and wetland fish species. Differences in fish assemblages among borrow-pit lakes were linked to engineered morphologic features, suggesting that diversity in engineering can contribute to diversity in fish assemblages; however, more research is needed to match engineering designs with fish assemblage structures that best meet conservation needs.

Modeling sludge accumulation rates in lined pit latrines in slum ...

African Journals Online (AJOL)

Yvonne

should include geo-physical characterization of soil and drainage of pit latrine sites so as ... Key words: Faecal, sludge accumulation rates, slum areas, lined pit latrines. .... Value and its unit Source .... overall quality of the models had to be assessed by validation on ..... Sanitation partnership series: Bringing pit emptying out.

Effect of microcrystallization on pitting corrosion of pure aluminium

International Nuclear Information System (INIS)

Meng Guozhe; Wei Liyan; Zhang Tao; Shao Yawei; Wang Fuhui; Dong Chaofang; Li Xiaogang

2009-01-01

A microcrystalline aluminium film with grain size of about 400 nm was prepared by magnetron sputtering technique. Its corrosion behaviour was investigated in NaCl containing acidic solution by means of potentiodynamic polarization curves and electrochemical noise (EN). The polarization results indicated that the corrosion potential of the sample shifted towards more positive direction, while its corrosion current density decreased compared with that of pure coarse-grain Al. The EN analysis based on stochastic model demonstrated that there existed two kinds of effect of microcrystallization on the pitting behaviour of pure aluminium: (1) the rate of pit initiation is accelerated, (2) the pit growth process was impeded. This leads to the enhancement of pitting resistance for the microcrystallized aluminium.