Reverse logistics applied to offshore exploration drilling; A logistica reversa aplicada as operacoes de perfuracao exploratoria 'offshore'

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Paulo Roberto dos Santos; Silva, Douglas Resende Teixeira da [Repsol YPF Brasil S.A. - Unidade de Negocios. Exploracao e Producao(Brazil); Moyano, Ignacio Sanchez [Universidad Politecnica de Madrid (Spain); Ferreira Filho, Virgilio Jose Martins; Valle, Rogerio [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

Reverse Logistic manages the return of resources and related information to production unities, after their use. Nowadays, it includes a special focus on environmental implications of used products, such as waste recycling or disposal. This paper considers the feasibility of reverse logistics for offshore exploration drilling activities, involving environmental aspects such as recycling, reuse of products after utilization and reduction of raw materials requirements. Although in Brazil the environmental licensing demands oil companies to have an organized management of their waste (requiring a total control over the final destination of the waste), costs and possible returns for waste management are considered negligible, in face of high oil prices and limited availability of offshore drilling rigs. Consequently, any potential benefit from its efficient management, or even reuse or trade, is not taken into account during the operation planning stage. The paper proposes Life Cycle Management as a continuous improvement management system aimed to minimize the environmental and socio-economic burdens associated with oil offshore production throughout its entire life cycle and value chain, that could provide cost-cuts such as a reduction in raw materials needs through reuse of waste, or even as a real income if selling the waste and/or recycled materials. (author)

Well control during the drilling and testing of high pressure offshore wells

Energy Technology Data Exchange (ETDEWEB)

1992-05-01

This Code has been prepared for use as a guide to safe practice for those concerned with well control during the drilling and testing of high pressure offshore wells. It is intended to provide information and guidance on those well control activities associated with high pressure wells which have an impact on safety offshore, and therefore require detailed care and attention. The Code has been produced in a United Kingdom Continental Shelf (UKCS) context, but the principles and recommendations have general relevance to similar operations elsewhere. Each chapter of the Code covers an important aspect of well control and has an introduction which describes the part each activity plays in the drilling and testing of high pressure offshore wells. (Author)

Information on commercial disposal facilities that may have received offshore drilling wastes.

Energy Technology Data Exchange (ETDEWEB)

Gasper, J. R.; Veil, J. A.; Ayers, R. C., Jr.

2000-08-25

The U.S. Environmental Protection Agency (EPA) is developing regulations that would establish requirements for discharging synthetic-based drill cuttings from offshore wells into the ocean. Justification for allowing discharges of these cuttings is that the environmental impacts from discharging drilling wastes into the ocean may be less harmful than the impacts from hauling them to shore for disposal. In the past, some onshore commercial facilities that disposed of these cuttings were improperly managed and operated and left behind environmental problems. This report provides background information on commercial waste disposal facilities in Texas, Louisiana, California, and Alaska that received or may have received offshore drilling wastes in the past and are now undergoing cleanup.

75 FR 39518 - National Commission on the BP Deepwater Horizon Oil Spill and Offshore Drilling; Correction

Science.gov (United States)

2010-07-09

... DEPARTMENT OF ENERGY National Commission on the BP Deepwater Horizon Oil Spill and Offshore Drilling; Correction AGENCY: Office of Fossil Energy, Department of Energy. ACTION: Notice of open meeting... Spill and Offshore Drilling, (75 FR 37783). This document makes several corrections to that notice. FOR...

Reverse logistics applied to offshore exploration drilling; A logistica reversa aplicada as operacoes de perfuracao exploratoria 'offshore'

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Paulo Roberto dos Santos; Silva, Douglas Resende Teixeira da [Repsol YPF Brasil S.A. - Unidade de Negocios. Exploracao e Producao(Brazil); Moyano, Ignacio Sanchez [Universidad Politecnica de Madrid (Spain); Ferreira Filho, Virgilio Jose Martins; Valle, Rogerio [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

Reverse Logistic manages the return of resources and related information to production unities, after their use. Nowadays, it includes a special focus on environmental implications of used products, such as waste recycling or disposal. This paper considers the feasibility of reverse logistics for offshore exploration drilling activities, involving environmental aspects such as recycling, reuse of products after utilization and reduction of raw materials requirements. Although in Brazil the environmental licensing demands oil companies to have an organized management of their waste (requiring a total control over the final destination of the waste), costs and possible returns for waste management are considered negligible, in face of high oil prices and limited availability of offshore drilling rigs. Consequently, any potential benefit from its efficient management, or even reuse or trade, is not taken into account during the operation planning stage. The paper proposes Life Cycle Management as a continuous improvement management system aimed to minimize the environmental and socio-economic burdens associated with oil offshore production throughout its entire life cycle and value chain, that could provide cost-cuts such as a reduction in raw materials needs through reuse of waste, or even as a real income if selling the waste and/or recycled materials. (author)

Modeling the time and cost to drill an offshore well

International Nuclear Information System (INIS)

Kaiser, Mark J.

2009-01-01

The objective in drilling a hydrocarbon well is to make hole as quickly as possible subject to the technological, operational, quality, and safety constraints associated with the process. These objectives are frequently conflicting and depend on factors that are subject to significant private and market uncertainty. There is no way to identify all of the relevant characteristics of drilling operations, but through use of statistical analysis and empirical modeling, it is possible to develop relations that characterize and benchmark drilling performance under a suitable set of assumptions. The purpose of this paper is to develop the conceptual framework to model the time and cost to drill an offshore well and to illustrate the methodology on a test set of wells in the Gulf of Mexico. The physical characteristics of the wellbore and operational aspects of drilling, including variables such as the drilled interval, horizontal displacement, aspect ratio, number of casing strings, and mud weight, serve as the primary descriptive factors in the functional relations constructed.

Project for Offshore Horizontal Directional Drilling (HDD for Pipeline Crossing in Bukit Tua, Indonesia

Directory of Open Access Journals (Sweden)

Yusuf Sofyan

2016-09-01

Full Text Available Horizontal Directional Drilling (HDD is commonly associated with well exploration activity, onshore road crossing, nearshore pipeline installation, and offshore pipeline crossing which requires precise alignment of two barges from one to the other. Here, the purpose of this study was to show one of the projects that was successfully performed on December 2013 for the Bukit Tua Project in East Java, Indonesia costing USD 8 Million. From this project experience, there are 6 Best Practices in HDD Offshore Project for Pipeline Crossing Application (first in region which will serve as a guide to future projects in replicating similar success. Out from 6 Best practices, there are two main recipes for success of HDD offshore for offshore crossings which are the drilling fluid also known as mud, and the Gyro Steering Tool (GST. First, mud parameter varies on case by case basis depending on the soil condition at the location where HDD will be performed. Failure to maintain the above parameters may result in catastrophic failure whereby the bore hole may collapse and pipe may get stuck underneath the seabed. Secondly, the beauty of GST is extremely accurate and unaffected by other metal anomalies during drilling process, thus ensuring the curve profile and direction of drilling are as per design throughout the whole process.

Regulatory capture by default: Offshore exploratory drilling for oil and gas

International Nuclear Information System (INIS)

Portman, Michelle E.

2014-01-01

This article examines a form of regulatory capture that occurs when significant ambiguity exists regarding the environmental protection standards for new types of activities in the marine environment. To begin with, there is little research that categorizes the typologies of regulatory capture despite the ubiquity of the phenomenon. After a discussion of theoretical approaches to regulatory capture, I describe the operative definition and theory appropriate to the situation related to authorization of oil and natural gas production in Israel following the discovery of large offshore reserves in 2010. This approach, embodying several facets of existing typologies, is applied to decisions made authorizing construction of the Gabriella offshore exploratory drilling platform. The analysis highlights the nature of capture in the absence of clear agency jurisdiction over new activities located in offshore environs organized as temporal and spatial “vacuums”. I conclude that comprehensive marine spatial planning would result in less capture and the development of more capture-resistant regulations. - Highlights: • Regulatory capture occurs when ambiguity exists about environmental protection standards for new types of activities in the marine environment. • A typology is developed from theories of regulatory capture (RC) and applied to cases of offshore exploratory drilling. • The typology is applied to offshore natural gas reserves discovered in 2010 offshore of Israel in the Mediterranean Sea. • Temporal aspects (anachronistic laws and regulations) and spatial aspects (jurisdictional ambiguity) have created regulatory vacuums leading to RC. • Comprehensive marine spatial planning would result in less capture and the development of more capture-resistant regulations

Offshore disposal of oil-based drilling fluid waste

International Nuclear Information System (INIS)

Malachosky, E.; Shannon, B.E.; Jackson, J.E.

1991-01-01

Offshore drilling operations in the Gulf of Mexico may use oil-based drilling fluids to mitigate drilling problems. The result is the generation of a significant quantity of oily cuttings and mud. The transportation of this waste for onshore disposal is a concern from a standpoint of both personnel safety and potential environmental impact. A process for preparing a slurry of this waste and the subsequent disposal of the slurry through annular pumping has been put into use by ARCO Oil and Gas Company. The disposal technique has been approved by the Minerals Management Service (MMS). The slurried waste is displaced down a casing annulus into a permeable zone at a depth below the surface casing setting depth. The annular disposal includes all cuttings and waste oil mud generated during drilling with oil-based fluids. This disposal technique negates the need for cuttings storage on the platform, transportation to shore, and the environmental effects of onshore surface disposal. The paper describes the environmental and safety concerns with onshore disposal, the benefits of annular disposal, and the equipment and process used for the preparation and pumping of the slurry

The Role of Well Control Training in Developing Safe Onshore and Offshore Oil Drilling Operations

Science.gov (United States)

Abulhassn, Aber

2016-01-01

This research investigates the role of the International Well Control Forum (IWCF) Rotary Drilling Well Control Training Program in developing safe oil drilling operations from the perspective of onshore and offshore drilling crews. The research methodology is a qualitative case study. A total of 40 IWCF candidates were interviewed, with 10 from…

Drilling in troubled waters. For an international regulation on offshore gas and oil activities

International Nuclear Information System (INIS)

Rochette, Julien

2014-01-01

Due to an increased energy demand, offshore activities are being extended to deep and ultra-deep waters: nearly one third of consumed oil and one quarter of consumed gas come from offshore drilling. This development threatens the environment and natural resources, and may have an impact on human activities which depend on the concerned ecosystems. As some accident had cross-border consequences, the relevance of the international regulatory framework is put into question again. This article first outlines the incomplete character of the legal framework for the safety of offshore activities: uncoordinated national systems, lack of an international convention, fragmented regional initiatives (some agreements exist for some specific regions: Arctic Sea, Baltic Sea, Mediterranean Sea, North-Eastern Atlantic, Persic Gulf and Oman Sea, Africa, western Indian Ocean). The author outlines that there is no international rules regarding responsibility and compensations. While highlighting the risks of a status-quo on these different issues, the author proposes and discusses a set of recommendations aimed at strengthening the regulation of offshore drilling activities

Geotechnical conditions and ice loading for an offshore drilling platform in the Canadian Beaufort Sea

Energy Technology Data Exchange (ETDEWEB)

Martens, S.; Eshraghian, A.; Rogers, B. [Klohn Crippen Berger Ltd., Calgary, AB (Canada)

2009-07-01

This paper addressed the geotechnical aspects of the deployment of the steel drilling caisson (SDC) at the Paktoa site in the Canadian Beaufort Sea. The SDC is a bottom founded mobile offshore drilling platform that can operate in 8 to 25 m of water in an Arctic environment. It is mated to a submersible barge in order to resist large ice forces on the structure at sites with relatively weak soils, without the need for site preparation. To date, the SDC has been deployed at 8 sites in the Canadian and Alaskan Beaufort Sea. This paper focused on the Paktoa location, where the SDC was deployed 50 km offshore in a water depth of 14 m during the winter of 2005-2006. Geotechnical investigations were conducted from the landfast ice prior to deployment and from the SDC deck. This paper described the soil properties and design loading; design stability; and deformation analysis. The environmental loads considered for the SDC design included ice push, waves and earthquakes. The ice loading was the dominant loading case. The instrumentation installed in the seabed included 2 push-in piezometers and an inclinometer. An ice loading event in February 2006 resulted in considerable displacements in the in-place inclinometer string below the SDC. Several analysis methods were used to estimate the magnitude of the ice load during this event in order to better understand the magnitude of ice loading for future Arctic deployments of gravity based drilling platforms. It was concluded that further deployments should have a minimum of 2 and preferably 4 in-place inclinometer strings to measure real-time deformation of the seabed to enable measurement of rotation of the structure that may occur due to asymmetrical ice loading. 10 refs., 2 tabs., 15 figs.

Well control during the drilling and testing of high pressure offshore wells

Energy Technology Data Exchange (ETDEWEB)

1992-05-01

This Code has been prepared for use as a guide to safe practice for those concerned with well control during the drilling and testing of high pressure offshore wells. It is intended to provide information and guidance on those well control activities associated with high pressure wells which have an impact on safety offshore, and therefore require detailed care and attention. The Code has been produced in a United Kingdom Continental Shelf (UKCS) context, but the principles and recommendations have general relevance to similar operations elsewhere. (author)

California study compares natural/drilling discharge contaminants offshore

International Nuclear Information System (INIS)

Steinhauer, W.G.; Imamura, E.; Barminski, J.R.; Neff, J.M.

1992-01-01

An analysis of drilling fluid and this paper reports that cuttings discharges in the southern Santa Maria basin offshore California indicates that the amount of metal and hydrocarbon contaminants from drilling operations is small relative to that from natural sources. The metal and hydrocarbon discharges were calculated for only one of the three platforms discharging between 1986 and 1989 in the Point Arguello field. However, assuming concentrations are similar on each platform, the combined input of metals and hydrocarbons over the 3-year period was still low (except for barium and lead) compared to the average annual flux from natural sources. The MMS is monitoring the Santa Maria basin to understand possible long-term environmental effects of oil and gas development (California Monitoring Program, Phase II; and Effects of OCS Production Platforms on Rocky Reef Fishes and Fisheries). A site-specific study area was established to determine effects of drilling-related discharges at Chevron U.S.S. Inc.'s platform Hidalgo in the Point Arguello field. Part of the study included review of discharge records for platforms Hidalgo, Hermosa (Chevron), and Harvest (Texaco Exploration and Production Inc.)

The final frontier: Tesco takes evolution of casing drilling system offshore

Energy Technology Data Exchange (ETDEWEB)

Polczer, S.

2000-04-01

Tesco Corporation is complementing its smaller 4 1/2-inch casing-while-drilling (CWD) tools by designing a series of 13 3/8-inch and a 9 5/8-inch underreamers and cutters to accommodate the larger diameter holes typical of offshore drilling. Tesco is building its own rig; it is a single rated to 3,000 metres that can be moved in seven loads with an overall 100 ton load rating. The unit features dimensional drilling capability in addition to features such as logging-while-drilling, and measurement-while-drilling. A conventional coring unit is employed via wireline. To date, Tesco has successfully overcome two of the main challenges in developing the new drilling process, i. e. to guarantee that casing can be run in high compression loads without damage to connections, and to develop an underreamer cutting structure to destroy rock at a rate comparable to conventional rotary drilling. The wireline retrieval system, which is 100 per cent reliable in running mode, but only 70 per cent successful in the retrieval mode, is the next challenge to be overcome. Tesco claims a 40 per cent reduction in overall 'spud to release' time, however, the main advantage claimed for the system is that the casing system protects the integrity of the hole as it is being drilled.

Emergency response in the Newfoundland offshore industry

Energy Technology Data Exchange (ETDEWEB)

Dempsey, J. [Cormorant Ltd., St. John' s, NL (Canada)

2006-07-01

This presentation reviewed current offshore oil activities with respect to safety issues regarding year-round marine operations in a harsh environment. Considerable logistics support is required for all offshore activities, including seismic and geotechnical surveys; exploration and production drilling; well testing; subsea construction; on-site production; and, delivery to market. Response to an offshore emergency must address the urgency of the incident along with stakeholder concerns. This presentation described the different types of emergencies and addressed issues regarding contingency planning; preventative measures; response philosophy; response scope; response at site; emergency management; communications links; and, oil spill response. The following current operations were highlighted: ExxonMobil's production drilling from the gravity-based concrete platform at Hibernia; Petro-Canada's production drilling at the Terra Nova FPSO; Husky Energy's production drilling at White Rose; and Chevron Canada's exploration drilling at the Orphan Basin. It was noted that in an emergency situation, the focus is on the welfare of offshore personnel. On an average day, the total offshore population is in the order of 1000 workers, all registered in the Personnel Logistics System which is updated with the departure of every helicopter from St. John's, Newfoundland or from the offshore platform. It is possible to prepare for foreseeable emergency incidents such as fire, explosion or gas leaks; spills to the marine environment; structural damage or collisions; persons lost at sea; helicopter or support vessel accidents; vessel sinking; sabotage; serious injuries or loss of life; severe ice events; and, loss of well control. The establishment of permanent safety zones at the Hibernia, White Rose and Terra Nova production fields are among the preventative measures, along with standby vessels that provide a rescue service for offshore installations

Emergency response in the Newfoundland offshore industry

International Nuclear Information System (INIS)

Dempsey, J.

2006-01-01

This presentation reviewed current offshore oil activities with respect to safety issues regarding year-round marine operations in a harsh environment. Considerable logistics support is required for all offshore activities, including seismic and geotechnical surveys; exploration and production drilling; well testing; subsea construction; on-site production; and, delivery to market. Response to an offshore emergency must address the urgency of the incident along with stakeholder concerns. This presentation described the different types of emergencies and addressed issues regarding contingency planning; preventative measures; response philosophy; response scope; response at site; emergency management; communications links; and, oil spill response. The following current operations were highlighted: ExxonMobil's production drilling from the gravity-based concrete platform at Hibernia; Petro-Canada's production drilling at the Terra Nova FPSO; Husky Energy's production drilling at White Rose; and Chevron Canada's exploration drilling at the Orphan Basin. It was noted that in an emergency situation, the focus is on the welfare of offshore personnel. On an average day, the total offshore population is in the order of 1000 workers, all registered in the Personnel Logistics System which is updated with the departure of every helicopter from St. John's, Newfoundland or from the offshore platform. It is possible to prepare for foreseeable emergency incidents such as fire, explosion or gas leaks; spills to the marine environment; structural damage or collisions; persons lost at sea; helicopter or support vessel accidents; vessel sinking; sabotage; serious injuries or loss of life; severe ice events; and, loss of well control. The establishment of permanent safety zones at the Hibernia, White Rose and Terra Nova production fields are among the preventative measures, along with standby vessels that provide a rescue service for offshore installations. Supply vessels are also

To drill or not to drill? An econometric analysis of US public opinion

International Nuclear Information System (INIS)

Mukherjee, Deep; Rahman, Mohammad Arshad

2016-01-01

Offshore drilling in the United States (US) has been the subject of public and political discourse due to multiple reasons which include economic impact, energy security, and environmental hazard. Consequently, several polls have been conducted over time to gauge public attitude towards offshore drilling. Nevertheless, the economic literature on this issue is sparse. This paper contributes to the literature and analyzes support for offshore drilling based on demographic, economic, social, belief, and shock (e.g. spill) factors. The data is taken from ten nationwide surveys conducted before, during and after the British Petroleum (BP) oil spill and analyzed within the framework of discrete choice model. The results from an ordinal probit model demonstrate that age, annual household income, affiliation to Republican Party, and residence in oil-rich states positively affect the probability of strong support and reduce the probability of strong opposition for offshore drilling. In contrast, the female gender, higher education, association to Democratic Party, and environmental concern affect opinion in opposite direction. Marginal effects show that belief about environmental consequences of drilling has the highest impact on opinion. Binary probit model also yields a similar result and suggests that BP oil disaster resulted in a transient decrease in support for offshore drilling. - Highlights: •US public opinion on offshore drilling is analyzed based on ten national polls. •Ordinal and binary probit models are utilized to identify the underlying factors that shape public opinion. •Belief about environmental cost of drilling and educational attainment have the highest negative impact on opinion. •Age, income, affiliation to Republican party and oil-rich states positively affect support for drilling. •BP oil spill resulted in a transient decrease in support for offshore drilling.

The economic impact of proposed regulations on the discharge of drilling muds and cuttings from the offshore facilities on US undiscovered crude oil reserves

International Nuclear Information System (INIS)

1989-01-01

This paper presents the results of an assessment of the potential economic impact of proposed regulations. on the discharge of drilling fluids (muds) and cuttings on US offshore undiscovered crude oil resources. These regulations include proposed Best Available Technology economically achievable (BAT) and New Source Performance Standards (NSPS) effluent limitations under the Clean Water Act governing the discharge of drilling fluids and drill cuttings from offshore oil and gas drilling operations. The impact of the proposed RAT/NSPS regulations for the drilling fluids and drill cuttings disposal on the cost of funding, developing, and producing Lower-48 offshore undiscovered crude oil resources will depend significantly on operators perceptions on the chances of failing toxicity or static sheen tests. If operators, in economically justifying their projects, assume that the fluids fail one of these tests, thereby prohibiting them from being discharged, up to 11% of the economically recoverable offshore resource would be considered uneconomic to produce. This would amount to 845 million barrels of oil at an oil price around $25 per barrel. On the other hand, if operators are willing co take their chances and see if their fluids fail one of these tests, then, based on EPA's assumptions concerning forecast fluid use and static sheen and toxicity test failure rates, up to 4% of the offshore undiscovered resource would be impacted, amounting to lost reserves of up to 270 million barrels

Pre-drilling prediction techniques on the high-temperature high-pressure hydrocarbon reservoirs offshore Hainan Island, China

Science.gov (United States)

Zhang, Hanyu; Liu, Huaishan; Wu, Shiguo; Sun, Jin; Yang, Chaoqun; Xie, Yangbing; Chen, Chuanxu; Gao, Jinwei; Wang, Jiliang

2018-02-01

Decreasing the risks and geohazards associated with drilling engineering in high-temperature high-pressure (HTHP) geologic settings begins with the implementation of pre-drilling prediction techniques (PPTs). To improve the accuracy of geopressure prediction in HTHP hydrocarbon reservoirs offshore Hainan Island, we made a comprehensive summary of current PPTs to identify existing problems and challenges by analyzing the global distribution of HTHP hydrocarbon reservoirs, the research status of PPTs, and the geologic setting and its HTHP formation mechanism. Our research results indicate that the HTHP formation mechanism in the study area is caused by multiple factors, including rapid loading, diapir intrusions, hydrocarbon generation, and the thermal expansion of pore fluids. Due to this multi-factor interaction, a cloud of HTHP hydrocarbon reservoirs has developed in the Ying-Qiong Basin, but only traditional PPTs have been implemented, based on the assumption of conditions that do not conform to the actual geologic environment, e.g., Bellotti's law and Eaton's law. In this paper, we focus on these issues, identify some challenges and solutions, and call for further PPT research to address the drawbacks of previous works and meet the challenges associated with the deepwater technology gap. In this way, we hope to contribute to the improved accuracy of geopressure prediction prior to drilling and provide support for future HTHP drilling offshore Hainan Island.

South America: Brazil leads the way in offshore drilling

Energy Technology Data Exchange (ETDEWEB)

1975-08-15

Brazil has found more than 600 million barrels of oil in the Campos basin and made other strikes to the north, offshore Sergipe, Alagoas, and Rio Grande do Norte states. Argentina's government recently gave the state oil company (YPF) permission to prospect in the Falkland Islands area about 200 miles east of Argentina's southern tip. YPF also is expected to accelerate work offshore Tierra del Fuego next year. The nationalization of petroleum in Venezuela is discussed. Drilling activity has slowed to 67 percent of the level of 1974. The goal for 1975 is about 875 million barrels. Chile has revised its oil law to permit foreign companies to explore, develop and produce the country's resources via contracts. Despite spotty successes, Peru has not given up on the northeastern jungle area, just south of Ecuador's fields. Occidental Petroleum and Petroperu have been the only companies to find commercial oil in the four-year exploration period. Their reserves are put at 464 million barrels. Eighteen foreign companies signed 14 contracts covering more than 50,000 square miles in Bolivia since the country asked for outside help in 1972. Ecuador's output reached an all-time high of 244,000 bpd and then slowed down to a 27,000 bpd dribble when the Trans-Ecuador pipeline broke. The government decreed that production from the Texaco and Gulf fields in the Oriente must rise to 210,000 bopd and that the two companies must drill their unexplored and undeveloped acreage or lose it. Ecuador cut 43 cents from the price of oil by reducing the production tax. Colombia abolished all oil concessions this year in an attempt to stem steadily slipping production. Exploration activities in Uruguay and Paraguay are discussed. (MCW)

8. report of the Standing Senate Committee on energy, the environment and natural resources : facts do not justify banning Canada's current offshore drilling operations : a Senate review in the wake of BP's Deepwater Horizon incident

Energy Technology Data Exchange (ETDEWEB)

Angus, W.D.; Mitchell, G. (comps.)

2010-08-15

The blowout of BP's Macondo well in the Gulf of Mexico has prompted many drilling practice reviews worldwide. This review by Canada's Senate Committee on Energy, the Environment and Natural Resources investigated Canadian offshore drilling practices. It showed that the risk of an offshore accident is quite low, partly because of the small amount of drilling currently underway in Canada. As a result, the committee recommended against a moratorium on offshore drilling. The study found that Canada's regulations for safety are more stringent than regulations in the United States. This report has elicited further reviews of liability and responsibility issues regarding offshore drilling. The Canadian legislation specifies that oil and gas companies are responsible for all spill clean-up costs and damage compensation. A $30 million absolute liability fund covers blowout costs for drilling in Canada's east offshore coast. A second civil liability fund requires drilling companies to provide Canadian regulators access to $70 million to cover damages from fault or negligence in offshore drilling. In addition, well operators may be required to provide evidence that they have a minimum of $250 million to fund well control, well safety and spill cleanup expenses. This report recommended a comprehensive review of liability, including whether thresholds should be adjusted to reflect current economic realities. refs., tabs., figs.

Effects of offshore oil drilling on benthic invertebrate communities on the Grand Banks (North Atlantic)

Energy Technology Data Exchange (ETDEWEB)

DeBlois, E. [Jacques Whitford Ltd., St. John' s, NL (Canada); Wight, F. [Husky Oil Operations Ltd., St. John' s, NL (Canada); Taylor, D. [DG Taylor Inc., Conception Bay South, NL (Canada); Paine, M. [Paine, Ledge and Associates, North Vancouver, BC (Canada)

2007-07-01

Drilling occurs at three different drill centres of the White Rose (WR) oil platform that lies 350 km offshore from St. John's Newfoundland. An extensive environmental effects monitoring (EEM) program conducted by Husky Energy is underway at the WR site. The sediment component of the program involves the measurement of physical and chemical characteristics, an assessment of toxicity in laboratory tests, and an assessment of in situ benthic invertebrate communities. Baseline sampling occurred in 2000, followed by post-drilling sampling in 2004 to 2006. The sediment is 95 per cent sand, with polychaetes and bivalves dominating the invertebrate communities. A comparative evaluation was performed for regressions between community variables and distances from drill centres before and after drilling. Concentration-response relationships between community variables and concentrations of major constituents in drilling muds (C10-C21 HCs) were also compared among years. It was shown that the biological effects on invertebrate communities were highly restricted to reductions in the amount of Paraonidae and Amphipoda near drill centres and at higher C10-C21 HC concentrations. The study revealed that the two most abundant invertebrate communities were not influenced by drilling in terms of standing crop, richness, diversity and evenness.

Environmental effects of exploratory drilling offshore Canada : environmental effects monitoring data and literature review : final report

International Nuclear Information System (INIS)

Hurley, G.; Ellis, J.

2004-10-01

This study examined pertinent environmental effects monitoring (EEM) information and data associated with offshore exploratory and development drilling in Canada. Two approaches were used: (1) a review of scientific literature was conducted to provide a synthesis of knowledge concerning interactions between exploratory drilling and the environment; and (2) a review of pertinent Canadian EEM data was conducted to evaluate interactions between exploratory drilling and the environment. Virtually all the east coast Canadian data reviewed in the study related to the effects of multiple wells. Although the effects of drilling waste were a primary focus, the effects of accidental discharges, lights and flaring, atmospheric emissions and noise emissions were also considered. Changes in the diversity and abundance of benthic organisms were detected within 1000 metres of many drill sites. The fine particles in drilling wastes contributed to the environmental effects observed around drilling platforms, and elevated body burden concentrations of drill waste indicators were detected over larger scales in a wide range of taxonomic groups. The results of laboratory and field studies suggested a lower potential for toxicity on commercial finfish and shellfish species. However, it was observed that measuring the effects of elevated concentrations of contaminants remained a challenge due to high levels variability in literature studies. A precautionary approach to the management of seismic surveys was recommended. It was concluded that the potential cumulative impacts of exploration drilling should be considered in the context of other anthropogenic activities. 138 refs., 6 tabs.

Elemental composition of airborne dust in the Shale Shaker House during an offshore drilling operation.

Science.gov (United States)

Hansen, A B; Larsen, E; Hansen, L V; Lyngsaae, M; Kunze, H

1991-12-01

During 2 days of an offshore drilling operation in the North Sea, 16 airborne dust samples from the atmosphere of the Shale Shaker House were collected onto filters. During this operation, drilling mud composed of a water slurry of barite (BaSO4) together with minor amounts of additives, among them chrome lignosulphonate and chrome lignite, was circulated between the borehole and the Shale Shaker House. The concentration of airborne dust in the atmosphere was determined and the elemental composition of the particles analysed by both PIXE (proton-induced X-ray emission) and ICP-MS (inductively coupled plasma-mass spectrometry). The total amount of dust collected varied from 0.04 to 1.41 mg m-3 with barium (Ba) as the single most abundant element. The open shale shakers turned out to be the major cause of generation of dust from the solid components of the drilling mud.

Case study : a real-time collaborative workflow for geosteering a horizontal well offshore eastern Canada

Energy Technology Data Exchange (ETDEWEB)

Cutler, M.; Pineda, G. [Halliburton Energy Services, Bakersfield, CA (United States)

2002-06-01

A horizontal well can be geologically steered using a forward modelling geosteering software that helps determine the stratigraphic position of the drillstring and interpret the well in the reservoir. The software shows reservoir engineers how to maximize the pay zone, optimize the well path, characterize reservoir properties and avoid entering undesired beds or fluid contacts. The best way to maximize the pay zone is to use an integrated arrangement of formation evaluation tools, software and reservoir engineering expertise. This paper presents a series of measurements while drilling and logging. Drilling (MWD/LWD) tools obtain real-time data and forward modelling while drilling software. When interpreted by a trained specialist, these tools help in decision making processes regarding reservoir depletion. The paper presents a case study from offshore eastern Canada in which a well was drilled horizontally from a semi-submersible mobile drilling unit. StrataSteer {sup TM}, a software tool developed by Halliburton Energy Services, was used to interpret the LWD data. The software is compatible with other downhole tools and the INSITE information system which provides real-time data. The objective of the study is to demonstrate the capabilities of the forward modelling tool while drilling the well. A computer was set up at the client's office and at the offshore rig site. The geological model which was constructed using the acquired data was then used to make real-time collaborative decisions to land the well correctly in the reservoir, maximize the productive interval, optimize the well path, and analyze the reservoir properties. However, it was noted that due to geological uncertainty, the objectives in this well were not achieved. 6 figs.

Drill cuttings mount formation study

Science.gov (United States)

Teh, Su Yean; Koh, Hock Lye

2014-07-01

Oil, Gas and Energy sector has been identified as an essential driving force in the Malaysian Economic Transformation Programs (ETP). Recently confirmed discovery of many offshore oil and gas deposits in Malaysian waters has ignited new confidence in this sector. However, this has also spurred intense interest on safeguarding the health and environment of coastal waters in Malaysia from adverse impact resulting from offshore oil and gas production operation. Offshore discharge of spent drilling mud and rock cuttings is the least expensive and simplest option to dispose of large volumes of drilling wastes. But this onsite offshore disposal may have adverse environmental impacts on the water column and the seabed. It may also pose occupational health hazards to the workers living in the offshore platforms. It is therefore important to model the transport and deposition of drilling mud and rock cuttings in the sea to enable proper assessment of their adverse impacts on the environment and the workers. Further, accumulation of drill particles on the seabed may impede proper operation of pipelines on the seabed. In this paper, we present an in-house application model TUNA-PT developed to cater to local oil and gas industry needs to simulate the dispersion and mount formation of drill cuttings by offshore oil and gas exploration and production platforms. Using available data on Malaysian coastal waters, simulation analyses project a pile formation on the seabed with a maximum height of about 1 m and pile radius of around 30 to 50 m. Simulated pile heights are not sensitive to the heights of release of the cuttings as the sensitivity has been mitigated by the depth of water.

Well successfully drilled with high performance water-based fluid: Santos Basins, offshore Brazil

Energy Technology Data Exchange (ETDEWEB)

Fornasier, Frank C.; Luzardo, Juan P. [Halliburton Company, Houston, TX (United States); Bishnoi, M.L. [Oil and Natural Gas Corporation Ltda. (ONGC), Dehradun (India)

2012-07-01

Santos Basin is a 352,260 square kilometers (136,010 sq mi) offshore pre-salt basin. It is located in the South Atlantic Ocean, some 300 kilometers (190 mi) South East of Sao Paulo, Brazil. One of the largest Brazilian sedimentary basins, it is the site of several recent significant oil fields, including Tupi and Jupiter. The criteria for drilling fluid selection is based upon the following factors: maximum cost efficiency, environmental friendliness, optimum borehole stability, and ease of use. The recommended drilling fluid formulation takes into consideration the experience gained during the drilling of wells in the Santos Basin area. The operator wanted to use a high-performance water-based fluid (HPWBF) that could provide shale inhibition, wellbore stability, lubricity and improved rate of penetration (ROP) as an alternative to synthetic-based drilling fluids to present value in terms of economics and environmental friendliness. The HPWBF consists of three synergistic products: a hydration suppressant, a dispersion suppressant, and an accretion suppressant. The system is formulated based on customized solutions for managing the clay reactivity. High logistics costs require drilling fluids that can be prepared with sea water and discharged to the sea without environmental impact. The HPWBF is a clay-free system designed for maximum shale inhibition in highly reactive formations. The system can provide wellbore stability, high rates of penetration, and acceptable rheological properties over a wide range of temperatures, with the added benefit of allowing cuttings discharge based upon water base environmental restrictions. Since no oil is used in the formulation, the HPWBF eliminates the need for cuttings processing and monitoring equipment, and exceeds the environmental requirements by achieving an LC50 value of 345,478.22 ppm in comparison with the minimum requirement (LC50 > 30,000 ppm in 96 hr), permitting use and discharge to the sea. The HPWBF selected

Dutch offshore skills assessed

Energy Technology Data Exchange (ETDEWEB)

Schaap, P

1988-11-01

The position is described of the different Dutch industries involved in the oil and gas exploitation business in the North Sea. Mentioned are, in the first place, the activities of towing services Smit Tak, and Wijsmuller. A well known drilling contractor is Neddrill. Drilling rigs are often designed in cooperation with consulting engineers firms Protech International, Heerema Engineering, Global Engineering, KTI, Fluor, and Tebodin. Drilling rigs constructors Grootint, Mercon Steel Structures, Heerema Havenbedrijf, HCG, Boele, and IHC have a sound name in the offshore construction scene. Offshore contractors like Heerema, Smit Tak, Volker Stevin and Allseas Engineering should be mentioned too. Special attention is given to the operation of saving drilling rigs in the Ekofisk field. Years of exploitation of oil and gas from this field resulted in subsidence of the sea floor, which endangered the drilling rigs. Hydraudyne designed the hydraulic lifter necessary for this saving operation. Dutch firms in this field have an estimated yearly turnover of Dfl 3 x 10/sup 9/. 6 figs.

Offshore in depth

Energy Technology Data Exchange (ETDEWEB)

Ebdon, J F

1968-08-01

The world-wide scope of offshore areas is discussed. Offshore areas of the U.S. and the world are where one of the ''hottest'' hydrocarbon booms--drilling, production, and pipelining--are in action today. Most of the current activity in offshore exploration and drilling is crude oil directed. However, big non-associated natural gas finds have been made. Additionally, for every barrel of crude oil produced, either or both associated natural gas and dissolved natural gas are produced in some varying ratio as casinghead gas. Thus, with worldwide production of some 2.5-million bbl of crude oil per day from offshore areas of Free-World countries, there are vast volumes of casinghead natural gas produced, over and above that produced from non-associated natural gas wells to the seaward of land masses. If offshore gas of any classification is produced in commercial volumes close to onshore population centers, then the possibility of marketing is fairly good. If remote from population centers, it is usually flared or shut-in. The development of gas liquefaction and cryogenic tankers has started, but international ocean traffic in LNG is still in its infancy. Current offshore gas pipelines are described.

Atmospheric metallic and arsenic pollution at an offshore drilling platform in the Bo Sea: A health risk assessment for the workers.

Science.gov (United States)

Xu, Hong; Han, Suqin; Bi, Xiaohui; Zhao, Zhijing; Zhang, Lei; Yang, Wenjie; Zhang, Min; Chen, Jing; Wu, Jianhui; Zhang, Yufen; Feng, Yinchang

2016-03-05

To investigate the ambient metal pollution at the offshore drilling platform in the Bo Sea, which few studies have focused on, PM2.5 samples were collected and ten heavy metals, as well as As, were analyzed. High concentration levels of metals were observed, and the heavy metal pollution was quite serious compared to air quality standards and other marine areas. Back trajectories and wind dependent and PCA analyses showed that the marine sources included ship traffic emissions and corrosive stainless steels from the equipment at the platform as well as industrial emissions from stainless steel production and coal combustion sources, which were transported from the surrounding mainland. Both contributed greatly to the ambient metallic particles at the offshore platform. The Hazard Index values of the metals, which were much less than 1, the Carcinogenic Risk data, which were lower than the EPA's acceptable range, and the fact that the metal concentrations did not the exceed the permissible exposure limits of OSHA, indicated that the health risks from the ambient metallic particles for the oil-drilling workers were not significant. Copyright © 2015 Elsevier B.V. All rights reserved.

Record reach : ExxonMobil extends its own world record

Energy Technology Data Exchange (ETDEWEB)

Wells, P.

2008-06-15

Extended reach drilling (ERD) records are now regularly being broken by ExxonMobil Corporation's Sakhalin project on Russia's east coast. In 2008, an oil well on the coast established a new record by achieving a measured depth of 11,680 meters. The well was punched out by a Texas-based drilling company using the world's largest land-based drilling rig. The use of ERD has reduced the capital and operating costs of the project in addition to reducing its environmental impacts. ERD has been used to drill onshore beneath the seafloor and has eliminated the need for additional offshore structure and pipelines. The horizontal reach of the wells has improved productivity while also avoiding disturbing whale migrations in the region. The rig features a 1.5 million pound load capacity, 3000 horsepower draw-works. The top-drive drilling systems were used to transmit real time data to external locations for further evaluation. Oil and gas is also produced from a gravity-based offshore platform. It was concluded that longer wellbore are now being developed by the corporation in order to drill under the Beaufort Sea. 2 figs.

Comparative analysis of numerical models of pipe handling equipment used in offshore drilling applications

Energy Technology Data Exchange (ETDEWEB)

Pawlus, Witold, E-mail: witold.p.pawlus@ieee.org; Ebbesen, Morten K.; Hansen, Michael R.; Choux, Martin; Hovland, Geir [Department of Engineering Sciences, University of Agder, PO Box 509, N-4898 Grimstad (Norway)

2016-06-08

Design of offshore drilling equipment is a task that involves not only analysis of strict machine specifications and safety requirements but also consideration of changeable weather conditions and harsh environment. These challenges call for a multidisciplinary approach and make the design process complex. Various modeling software products are currently available to aid design engineers in their effort to test and redesign equipment before it is manufactured. However, given the number of available modeling tools and methods, the choice of the proper modeling methodology becomes not obvious and – in some cases – troublesome. Therefore, we present a comparative analysis of two popular approaches used in modeling and simulation of mechanical systems: multibody and analytical modeling. A gripper arm of the offshore vertical pipe handling machine is selected as a case study for which both models are created. In contrast to some other works, the current paper shows verification of both systems by benchmarking their simulation results against each other. Such criteria as modeling effort and results accuracy are evaluated to assess which modeling strategy is the most suitable given its eventual application.

A Risk Analysis Methodology to Address Human and Organizational Factors in Offshore Drilling Safety: With an Emphasis on Negative Pressure Test

Science.gov (United States)

Tabibzadeh, Maryam

According to the final Presidential National Commission report on the BP Deepwater Horizon (DWH) blowout, there is need to "integrate more sophisticated risk assessment and risk management practices" in the oil industry. Reviewing the literature of the offshore drilling industry indicates that most of the developed risk analysis methodologies do not fully and more importantly, systematically address the contribution of Human and Organizational Factors (HOFs) in accident causation. This is while results of a comprehensive study, from 1988 to 2005, of more than 600 well-documented major failures in offshore structures show that approximately 80% of those failures were due to HOFs. In addition, lack of safety culture, as an issue related to HOFs, have been identified as a common contributing cause of many accidents in this industry. This dissertation introduces an integrated risk analysis methodology to systematically assess the critical role of human and organizational factors in offshore drilling safety. The proposed methodology in this research focuses on a specific procedure called Negative Pressure Test (NPT), as the primary method to ascertain well integrity during offshore drilling, and analyzes the contributing causes of misinterpreting such a critical test. In addition, the case study of the BP Deepwater Horizon accident and their conducted NPT is discussed. The risk analysis methodology in this dissertation consists of three different approaches and their integration constitutes the big picture of my whole methodology. The first approach is the comparative analysis of a "standard" NPT, which is proposed by the author, with the test conducted by the DWH crew. This analysis contributes to identifying the involved discrepancies between the two test procedures. The second approach is a conceptual risk assessment framework to analyze the causal factors of the identified mismatches in the previous step, as the main contributors of negative pressure test

Environmental risk in the offshore industry

International Nuclear Information System (INIS)

Woods, I.T.; Shirley, D.; Bottelberghs, P.H.

1991-01-01

The subject of oil pollution of the sea by the offshore industry is topical as a result of recent incidents both in the U.K. and overseas. While these incidents have primarily involved crude carriers, it has led to pressure to quantify the risk to the environment from the offshore industry in general. In this paper a method for the assessment of the frequency and size of oil spills from offshore installations is presented. It relies on previously reported spills to determine spill size/frequency information for a range of offshore activities, such as transport by pipeline, drilling and processing. Modification factors are used so local conditions, such as the number of wells drilled, throughput and well depth, can be considered in the assessment of the oil spill risk from a particular installation

The International Standards Organisation offshore structures standard

International Nuclear Information System (INIS)

Snell, R.O.

1994-01-01

The International Standards Organisation has initiated a program to develop a suite of ISO Codes and Standards for the Oil Industry. The Offshore Structures Standard is one of seven topics being addressed. The scope of the standard will encompass fixed steel and concrete structures, floating structures, Arctic structures and the site specific assessment of mobile drilling and accommodation units. The standard will use as base documents the existing recommended practices and standards most frequently used for each type of structure, and will develop them to incorporate best published and recognized practice and knowledge where it provides a significant improvement on the base document. Work on the Code has commenced under the direction of an internationally constituted sub-committee comprising representatives from most of the countries with a substantial offshore oil and gas industry. This paper outlines the background to the code and the format, content and work program

30 CFR 250.417 - What must I provide if I plan to use a mobile offshore drilling unit (MODU)?

Science.gov (United States)

2010-07-01

... both hurricane and non-hurricane seasons. If sufficient environmental information and data are not... requirements. You must provide information and data to demonstrate the drilling unit's capability to perform at the proposed drilling location. This information must include the maximum environmental and...

Catamaran type semisubmersible platform for offshore drilling

Energy Technology Data Exchange (ETDEWEB)

Pouget, G; Chevallier, J; Hampton, G

1988-06-10

A semi-submersible oil rig which allows the vertical storage of drilling tubes and drill pipes is presented. The structure which links the floaters to the bridge consists of hollow columns forming caissons and containing means for storing tubes.

Effects of the Terra Nova offshore oil development on benthic macro-invertebrates over 10 years of development drilling on the Grand Banks of Newfoundland, Canada

Science.gov (United States)

Paine, Michael D.; DeBlois, Elisabeth M.; Kilgour, Bruce W.; Tracy, Ellen; Pocklington, Patricia; Crowley, Roger D.; Williams, Urban P.; Gregory Janes, G.

2014-12-01

This paper describes effects of drilling with water and synthetic-based drilling muds on benthic macro-invertebrates over 10 years at the Terra Nova offshore oil development. As such, the paper provides insight on the effects of relatively new synthetic-based drilling muds (SBMs), and makes an important contribution to our understanding of the long-term chronic effects of drilling on benthic communities. The Terra Nova Field is located approximately 350 km offshore on the Grand Banks of Newfoundland (Canada). Sediment and invertebrate samples were collected in 1997 (baseline) prior to drilling, and subsequently in 2000, 2001, 2002, 2004, 2006, 2008 and 2010. Approximately 50 stations were sampled in each year at distances of less than 1 to approximately 20 km from drill centres. Summary benthic invertebrate community measures examined were total abundance, biomass, richness, diversity and multivariate measures of community composition based on non-Metric Dimensional Scaling (nMDS). Decreases in abundance, biomass and richness were noted at one station located nearest (0.14 km) to a drill centre in some environmental effects monitoring (EEM) years. These decreases coincided with higher levels of tracers of drill muds in sediments (barium and >C10-C21 hydrocarbons). Abundances of selected individual taxa were also examined to help interpret responses when project-related effects on summary measures occurred. Enrichment effects on some tolerant taxa (e.g., the polychaete family Phyllodocidae and the bivalve family Tellinidae) and decreased abundances of sensitive taxa (e.g., the polychaete families Orbiniidae and Paraonidae) were detected to within approximately 1-2 km from discharge source. Lagged responses three to five years after drilling started were noted for Phyllodocidae and Tellinidae, suggesting chronic or indirect effects. Overall, results of benthic community analyses at Terra Nova indicate that effects on summary measures of community composition were

Drilling fluid technologies : what goes in must come out

International Nuclear Information System (INIS)

Polczer, S.

1998-01-01

The treatment of drilling wastes contaminated with invert drilling muds was discussed. The tight emulsion properties which make invert drilling muds useful are the same properties that make their disposal so difficult. Potential long-term liability associated with inverts is another reason for reluctance to use these products. Inverts are toxic and highly mobile in the environment, and must therefore be handled with care. Often the costs associated with their disposal are greater than their potential benefits. Petro-Canada Lubricants has formulated a new, non-diesel based product called Drill Mud Oil HT40N which completely eliminates toxic aromatic molecules. It is composed of 98 per cent plus of cyclic and branched isoparaffins with an average carbon number of C16. The level of polynuclear aromatics is reduced to parts per billion levels. Drill Mud Oil HT40N was being used at Hibernia until an even newer product, IPAR3 synthetic drill mud oil, was developed exclusively for offshore use. Drill Mud Oil HT40N is less prone to flash fires, is odourless and is more likely to be used in places such as the Western Canada Sedimentary Basin. Drill Mud Oil HT40N works almost exactly the same as a diesel-based drill mud oil but has many advantages in terms of safety and ease of disposal, particularly in landfarming operations. Drill Mud Oil HT40N does not irritate the skin or release toxic fumes. The cost of Drill Mud Oil HT40N is higher than conventional diesel-based drilling muds. 2 figs

Offshore: nations needing our help to exploit oil and gas. [British offshore supply industry

Energy Technology Data Exchange (ETDEWEB)

Laird, R

1978-02-23

The opportunities around the world for Great Britian to sell companies its expertise on petroleum and natural gas drilling are surveyed. Hydrocarbon reserves; development plans, especially offshore drilling plans; needed equipment and technology; and investment requirements are a few of the factors discussed for Venezuela, Brazil, Mexico, India, Australia, Thailand, Malaysia, Indonesia, and Singapore. (MCW)

Subsea prizes : companies pushing the envelope offshore

Energy Technology Data Exchange (ETDEWEB)

Macedo, R.

2009-06-15

In order to make projects economic, companies are going farther offshore and deeper to find oil and gas or to use existing offshore platforms and longer horizontals. Companies such as StatoilHydro are reworking strategies on how to approach future oil finds. This article discussed examples of ultra deep and long horizontal oil finds such as Statoil's complicated but highly successful Gulltopp project. Although drilling ultra-deep wells or long horizontal wells is risky, they can also be very lucrative. The article also discussed McMoRan Exploration Company of New Orleans' high-risk deeper targets in the Gulf of Mexico and its exploration strategy. The longest well in the world, drilled by Maersk Oil Qatar AS was also described. The article noted that the Danish company reported that the entire horizontal section of the well was placed within a reservoir target which was only 20 feet thick. Schlumberger helped Maersk Oil Qatar break several records with extended reach drilling (ERD) offshore well. This well set 10 records, including the longest well ever drilled; longest along-hole departure; longest 8 and a half inch section; highest ERD ratio; highest directional drilling difficulty index; deepest directional control; deepest downlink, MWD transmission and LWD geosteering; deepest battery-less operation; longest reservoir contact; and longest open hole. Last, the article discussed an unsuccessful well drilled by Murphy Oil Corporation known as the Manhattan well. 8 figs.

Framework for a comparative environmental assessment of drilling fluids

Energy Technology Data Exchange (ETDEWEB)

Meinhold, A.F.

1998-11-01

During the drilling of an oil or gas well, drilling fluid (or mud) is used to maintain well control and to remove drill cuttings from the hole. In response to effluent limitation guidelines promulgated by the US Environmental Protection Agency (EPA) for discharge of drilling wastes offshore, alternatives to water and oil-based muds have been developed. These synthetic-based muds (SBMs) are more efficient than water-based muds (WBMs) for drilling difficult and complex formation intervals and have lower toxicity and smaller environmental impacts than diesel or conventional mineral oil-based muds (OBMs). A third category of drilling fluids, derived from petroleum and called enhanced mineral oils (EMOs), also have these advantages over the traditionally used OBMs and WBMs. EPA recognizes that SBMs and EMOs are new classes of drilling fluids, but their regulatory status is unclear. To address this uncertainty, EPA is following an innovative presumptive rulemaking process that will develop final regulations for SBM discharges offshore in less than three years. This report develops a framework for a comparative risk assessment for the discharge of SBMs and EMOs, to help support a risk-based, integrated approach to regulatory decision making. The framework will help identify potential impacts and benefits associated with the use of SBMs, EMOs, WBMs, and OBMs; identify areas where additional data are needed; and support early decision-making in the absence of complete data. As additional data becomes available, the framework can support a full quantitative comparative assessment. Detailed data are provided to support a comparative assessment in the areas of occupational and public health impacts.

Study of waste generation in the drilling and cementing operations during construction of offshore oil and gas wells

Directory of Open Access Journals (Sweden)

Letícia Ferraço de Campos

2016-12-01

Full Text Available This literature review aims to present drilling and cementing activities which take place during the construction of offshore oil and gas wells, listing the waste generated in each step. IBAMA, the environmental agency that regulates the activity, allows two disposal options for these wastes: disposal in open sea or treatment followed by disposal on shore. The documentary research applied in this article details the destination options showing that the monitoring required by the environmental agency is a way to track the actual results of the activities described.

Alterations in bottom sediment physical and chemical characteristics at the Terra Nova offshore oil development over ten years of drilling on the grand banks of Newfoundland, Canada

Science.gov (United States)

DeBlois, Elisabeth M.; Paine, Michael D.; Kilgour, Bruce W.; Tracy, Ellen; Crowley, Roger D.; Williams, Urban P.; Janes, G. Gregory

2014-12-01

This paper describes sediment composition at the Terra Nova offshore oil development. The Terra Nova Field is located on the Grand Banks approximately 350 km southeast of Newfoundland, Canada, at an approximate water depth of 100 m. Surface sediment samples (upper 3 cm) were collected for chemical and particle size analyses at the site pre-development (1997) and in 2000-2002, 2004, 2006, 2008 and 2010. Approximately 50 stations have been sampled in each program year, with stations extending from less than 1 km to a maximum of 20 km from source (drill centres) along five gradients, extending to the southeast, southwest, northeast, northwest and east of Terra Nova. Results show that Terra Nova sediments were contaminated with >C10-C21 hydrocarbons and barium-the two main constituents of synthetic-based drilling muds used at the site. Highest levels of contamination occurred within 1 to 2 km from source, consistent with predictions from drill cuttings dispersion modelling. The strength of distance gradients for >C10-C21 hydrocarbons and barium, and overall levels, generally increased as drilling progressed but decreased from 2006 to 2010, coincident with a reduction in drilling. As seen at other offshore oil development sites, metals other than barium, sulphur and sulphide levels were elevated and sediment fines content was higher in the immediate vicinity (less than 0.5 km) of drill centres in some sampling years; but there was no strong evidence of project-related alterations of these variables. Overall, sediment contamination at Terra Nova was spatially limited and only the two major constituents of synthetic-based drilling muds used at the site, >C10-C21 hydrocarbons and barium, showed clear evidence of project-related alternations.

Issues in offshore platform research - Part 1: Semi-submersibles

Science.gov (United States)

Sharma, R.; Kim, Tae-Wan; Sha, O. P.; Misra, S. C.

2010-09-01

Availability of economic and efficient energy resources is crucial to a nation's development. Because of their low cost and advancement in drilling and exploration technologies, oil and gas based energy systems are the most widely used energy source throughout the world. The inexpensive oil and gas based energy systems are used for everything, i.e., from transportation of goods and people to the harvesting of crops for food. As the energy demand continues to rise, there is strong need for inexpensive energy solutions. An offshore platform is a large structure that is used to house workers and machinery needed to drill wells in the ocean bed, extract oil and/or natural gas, process the produced fluids, and ship or pipe them to shore. Depending on the circumstances, the offshore platform can be fixed (to the ocean floor) or can consist of an artificial island or can float. Semi-submersibles are used for various purposes in offshore and marine engineering, e.g. crane vessels, drilling vessels, tourist vessels, production platforms and accommodation facilities, etc. The challenges of deepwater drilling have further motivated the researchers to design optimum choices for semi-submersibles for a chosen operating depth. In our series of eight papers, we discuss the design and production aspects of all the types of offshore platforms. In the present part I, we present an introduction and critical analysis of semi-submersibles.

Technology strategy for cost-effective drilling and intervention; Technology Target Areas; TTA4 - Cost effective drilling and intervention

Energy Technology Data Exchange (ETDEWEB)

2007-07-01

The main goals of the OG21 initiative are to (1) develop new technology and knowledge to increase the value creation of Norwegian oil and gas resources and (2) enhance the export of Norwegian oil and gas technology. The OG21 Cost-effective Drilling and Intervention (CEDI) Technology Target Area (TTA) has identified some key strategic drilling and well intervention needs to help meet the goals of OG21. These key strategic drilling and well intervention needs are based on a review of present and anticipated future offshore-Norway drilling and well intervention conditions and the Norwegian drilling and well intervention industry. A gap analysis has been performed to assess the extent to which current drilling and well intervention research and development and other activities will meet the key strategic needs. Based on the identified strategic drilling and well intervention needs and the current industry res each and development and other activities, the most important technology areas for meeting the OG21 goals are: environment-friendly and low-cost exploration wells; low-cost methods for well intervention/sidetracks; faster and extended-reach drilling; deep water drilling, completion and intervention; offshore automated drilling; subsea and sub-ice drilling; drilling through basalt and tight carbonates; drilling and completion in salt formation. More specific goals for each area: reduce cost of exploration wells by 50%; reduce cost for well intervention/sidetracks by 50%; increase drilling efficiency by 40%; reduce drilling cost in deep water by 40 %; enable offshore automated drilling before 2012; enable automated drilling from seabed in 2020. Particular focus should be placed on developing new technology for low-cost exploration wells to stem the downward trends in the number of exploration wells drilled and the volume of discovered resources. The CEDI TTA has the following additional recommendations: The perceived gaps in addressing the key strategic drilling and

A vision for drilling

Energy Technology Data Exchange (ETDEWEB)

Millheim, K. [Montanuniversitaet Leoben (Austria)

1995-12-31

The future of drilling lies in its relationship with the oil and gas industry. This paper examines how the future of drilling is seen from the view point of the exploration manager, the drilling contractor, the drilling engineer and the company president or managing director. The various pressures on the oil and gas industry are examined, such as environmental issues, alternative energy sources, and the price of oil which determines how companies are run. Exploration activity is driven by the price of oil and gas. The development of wells with multiple horizontal wells or multiple horizontal wells with tributaries will reduce the cost of exploration. Companies will rely less and less on reservoir simulation and more on cheap well-bores, multi-lateral well-bores and will exploit oil that could not be exploited before. The cost of exploratory drilling will need to be kept down so that in the future the industry will get better at economically finding fields at the 10 million to 20 million barrel range that would not have been possible before. The future is expected to see drilling contractors tunnelling, making sewerage lines and drilling 10,000 foot wells with purpose built rigs. Franchising will become a feature of the industry as will the use of databases to answer key technical questions. Offshore platforms will be built to be moveable and disposable. The industry is capable of solving problems, meeting challenges and making ideas work, providing much hope for the future. 10 figs., 1 photo.

A field investigation to determine the impact of offshore drilling activities on natural larval settlement

International Nuclear Information System (INIS)

Barnett, A.; Krause, P.R.; Raimondi, P.T.

1995-01-01

The authors used a manipulative field experiment to test the effects of offshore drilling activities on the natural settlement of invertebrate larvae in the deep ocean (180 m) off southern California. This experiment was conducted in conjunction with other in situ experiments at a series of three drilling rigs and three reference sites between Pt. Arguello and Pt. Conception. At each study site the authors exposed settling plates to the natural environment on moorings at each of two depths near the sea floor. The two mooring depths were used to simulate differences in natural relief found in the study area. These plates were covered with a mesh to allow only natural bacterial ''filming'' to occur and prevent settlement of larger invertebrate larvae. After filming the plates were transplanted to all sites near the bottom such that each site had plates filmed at all other sites. Sterile plates (without filming) were also placed at each site. Plates were left uncovered for periods up to three years. Settling plates were retrieved at specific intervals over the length of the experiment. Upon retrieval some plates were photographed and returned to the bottom, others were returned to the laboratory. The results showed that the overall settlement rate was very slow with little settlement occurring in the first 6 months of exposure. Settlement was higher in periods of exposure lasting between one and two years. The authors also found significant effects on the number and type of larvae that settled on the plates with respect to the location of the plates (rig vs. reference), and the height from the bottom where they were located

30 CFR 250.458 - What quantities of drilling fluids are required?

Science.gov (United States)

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations... the daily inventories of drilling fluid and drilling fluid materials, including weight materials and... drilling fluid material to maintain well control, you must suspend drilling operations. [68 FR 8423, Feb...

Environmental assessment report to BEPCo Canada Company on exploratory drilling on EL2407

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-19

BEPCo. Canada Company (BEPCo) is planning to drill exploratory deepwater wells offshore from Nova Scotia. This environmental assessment report was prepared to satisfy regulatory requirements associated with offshore drilling. It focuses on valued environmental components chosen during a scoping process. This report evaluated the potential project-related effects on marine benthos, marine fish, marine mammals, marine turtles, marine birds, special areas, and other ocean users. Discharges and emissions from the project include drilling mud and rock cuttings, small amounts of produced water, ship discharges and atmospheric emissions. This report includes oceanographic plume modelling for allowable discharges of mud and cuttings at sea. The report predicts that the potential adverse effects of the valued environmental components will be short term and highly localized around the drilling rigs. It was suggested that any adverse effects could be mitigated through the use of technically feasible mitigation and standard offshore oil and gas industry procedures for environmental health and safety. It was concluded that BEPCo's proposed drilling program for EL-2407 can be conducted without any significant adverse effects on Nova Scotia's offshore environment. 121 refs., 27 tabs., 24 figs.

Offshore regulators focus on incentives for safety

Energy Technology Data Exchange (ETDEWEB)

Reid, W.

2000-11-27

Strict safety regulations in effect at offshore drilling sites are discussed. The guiding principle in all existing regulation is that while economic or industrial considerations are important, the value and the concern for human life is paramount. Should some tragic event occur at an offshore drilling site that is shown to have been caused by negligence of an operator, there is no question at all that the regulatory authority, in this case the Canada-Newfoundland Offshore Petroleum Board (CNOPB), would take the negligent operator to court. Nevertheless, Canadian authorities remain confident that encouragement of maintaining a safe working environment is likely to be more successful in ensuring workplace safety than threats of punishment. Indeed, Canadian regulators have, in recent times, shown a tendency to move towards performance-based systems, as opposed to the more usual prescriptive or rule-bound regulatory regime. This new approach involves setting targets and giving companies the responsibility to implement measures to reach the targets rather than relying on government instructions. Still, performance-based regulation in Canada is relatively new and some regulations remain prescriptive. Examples are the requirement for two immersion suits and two lifeboat seats for every worker on a drilling unit.

U.S. drilling contractors could face stiff challenges

International Nuclear Information System (INIS)

Simmons, M.R.

1993-01-01

Although the outlook for most segments of the contract drilling business is now more optimistic than in the past decade, the increased activity has brought several problems: the availability of fully trained crews, the need for new capital, and the limited number of quality drillstrings. These problems will grow in importance if natural gas deliverability begins to decline visibly and once the scramble to correct this decline begins. As the drilling recovery unfolds, the most important lesson to remember, based on worldwide activity in the past year, is how rapidly conditions can change and how quickly excess capacity can turn into chronic shortages. The various segments of the world wide contract drilling industry's prospects have changed dramatically during the past 12 months, and oddly, some market sectors have improved while others have become worse. These quick changes highlight the unpredictable and volatile nature of the markets for contract drilling and other services needed to drill and complete oil and gas wells. The paper describes the business of well drilling onshore and offshore in the US, drilling activities in Canada, international markets, capacity, the supplies of natural gas, Gulf of Mexico activities, drill pipe shortages, manpower shortages, and challenges offshore

Issues in offshore platform research - Part 1: Semi-submersibles

Directory of Open Access Journals (Sweden)

R. Sharma

2010-09-01

Full Text Available Availability of economic and efficient energy resources is crucial to a nation's development. Because of their low cost and advancement in drilling and exploration technologies, oil and gas based energy systems are the most widely used energy source throughout the world. The inexpensive oil and gas based energy systems are used for everything, i.e., from transportation of goods and people to the harvesting of crops for food. As the energy demand continues to rise, there is strong need for inexpensive energy solutions. An offshore platform is a large structure that is used to house workers and machinery needed to drill wells in the ocean bed, extract oil and/or natural gas, process the produced fluids, and ship or pipe them to shore. Depending on the circumstances, the offshore platform can be fixed (to the ocean floor or can consist of an artificial island or can float. Semi-submersibles are used for various purposes in offshore and marine engineering, e.g. crane vessels, drilling vessels, tourist vessels, production platforms and accommodation facilities, etc. The challenges of deepwater drilling have further motivated the researchers to design optimum choices for semi-submersibles for a chosen operating depth. In our series of eight papers, we discuss the design and production aspects of all the types of offshore platforms. In the present part I, we present an introduction and critical analysis of semi-submersibles.

Dutch offshore suppliers in confident mood

International Nuclear Information System (INIS)

Beudel, M.

1998-01-01

A series of linked articles discusses the current state of the Netherland's offshore industry. Reduced taxes, and availability of exploration licenses has meant that explorers and producers are drawn to the small size, but frequent yield explorations on Holland's continental shelf. The excellent operation record of Rotterdam's Verolme Botlek yard; for repair and maintenance of offshore platforms and associated plant, is explored as the facility plans to diversify into newbuilding. The construction of an offshore basin designed for the hydrodynamic testing of offshore plant intended for deepwater use is described. The Netherlands maritime research institute (Marin) aims to stay at the forefront of offshore research and development with this new facility. Other articles cover pipe tensioning, new large linear winches and innovations in offshore drilling and production. (UK)

DESIGN OF OFFSHORE CONCRETE GRAVITY PLATFORMS

African Journals Online (AJOL)

gas industry. Manufacturing and construction methods are discussed. Current ... Keywords: concrete gravity platform, offshore, foundation design, manufacturing, ... forms are used to support production drilling ... Manufacture and Construction.

Stress and Pore Pressure Measurement in IODP Riser Drilling: An Example from Expedition 319, Kumano Basin offshore SW Honshu, Japan

Science.gov (United States)

Saffer, D. M.; McNeill, L. C.; Byrne, T. B.; Araki, E.; Flemings, P. B.; Conin, M.; Eguchi, N. O.; Takahashi, K.; Toczko, S.; Boutt, D. F.; Doan, M.; Kano, Y.; Ito, T.; Lin, W.

2009-12-01

In summer 2009, Integrated Ocean Drilling Program (IODP) Expedition 319 drilled a 1600 m deep riser borehole (Site C0009) in the Kumano Basin offshore SW Japan, to investigate the properties, structure and state of stress in the hanging wall above the subduction plate boundary. The first riser-based scientific drilling in IODP history allowed us to make several new scientific measurements including in situ stress magnitude, pore pressure and permeability using the Modular Formation Dynamics Tester (MDT) wireline tool, and measurement of minimum stress magnitude from Leak-off Tests (LOT). In addition, continuous monitoring of mud weight, mud gas, annular pressure, and mud losses provided data to constrain formation pore fluid pressure and stress. At Site C0009, we conducted 2 LOTs below a casing shoe at 708.6 m depth and 11 successful MDT measurements, including 9 single probe tests to measure pore pressure and fluid mobility and 2 dual packer tests: 1 to measure permeability by a drawdown test, and 1 to measure in situ stress. Measured pore pressures are approximately hydrostatic to 1463.7 m depth. We observed only minor gas shows when drilling ahead (as in-place methane was liberated from the rock at the bit) but little or no gas during pipe connections. This indicates that the borehole mud pressure exceeded the formation pore pressure, and is consistent with the MDT measurements. Permeabilities range from ~10-16 m2 - 10-14 m2, and the observed variation is consistent with lithologic changes defined in gamma ray logs. The MDT measurement at 874.3 mbsf and the LOT at 708.6 m yield values for the least principal stress of 34.8 MPa and 30.2 MPa, respectively. Both are less than the vertical stress (Sv) computed from density logs. Partial mud circulation losses occurred when the borehole mud pressure exceeded the leak-off stress measured at the base of the casing shoe; this provides an additional indirect constraint on Shmin magnitude. Mud pressure slightly in excess

Drilling rig mast

Energy Technology Data Exchange (ETDEWEB)

Bulgakov, E.S.; Barashkov, V.A.; Lebedev, A.I.; Panin, N.M.; Sirotkin, N.V.

1981-01-07

A drilling rig mast is proposed that contains a portal with a carrier shaft hinged to it and struts with stays. In order to decrease the time expended in the assembly and dessembly of the drilling rig, the portal is constructed from mobile and immobile parts that are connected together by a ball pivot; the immobile section of the portal has a T-shaped recess for directing the mobile section.

Offshore oil: Correctness of perspective

International Nuclear Information System (INIS)

Burns, R.F.

1993-01-01

Except for the Gulf of Mexico, the offshore oil industry has been virtually banned from the US Exclusive Economic Zone for ten years. The oil potential in Alaska's Arctic National Wildlife Refuge (ANWR) is also off limits. The Gulf of Mexico is the only place with prospects for future success and a number of companies both large and small are determined to move forward. The depressed price of oil does not encourage development but recently gas prices in the US have increased, making offshore gas development more feasible. Perhaps most significant is development and application of new technology and more intense management to make sure it works. The offshore oil companies and support industries have made significant technological advances, expending over and above the dollars paid in taxes, lease fees, and royalties. The ocean industries harbor a great reservoir of high technology knowledge. They have demonstrated the ability to successfully meet a vast array of challenges in exploring for, drilling, and producing oil and gas in extreme conditions. These facts beg the question as to the rational basis of each and every regulation and the ban on drilling

Review and Recommendations for the Interagency Ship Structure Committee’s Fiscal 1984 Research Program,

Science.gov (United States)

1983-01-01

Daily. Proposal Evaluation Procedure Organizations interested in doing the work adverstised submit proposals and cost estimates. The USCG contracting...types of offshore structures. These structures have largely been fixed platforms for petroleum drilling and production, and mobile offshore drilling...structures and of those mobile drilling units that are bottom supported, such as jack-ups and submersibles. Structures which are held in place by anchors

30 CFR 250.457 - What equipment is required to monitor drilling fluids?

Science.gov (United States)

2010-07-01

... monitor the drilling fluid returns. The indicator may be located in the drilling fluid-logging compartment... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What equipment is required to monitor drilling... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations...

You say you want a revolution: casing drilling targets 30 per cent well-cost saving

Energy Technology Data Exchange (ETDEWEB)

Polczer, S.; Marsters, S.

1999-10-01

Casing drilling is a new method of drilling that eliminates drill strings by using standard casing to simultaneously drill and case wells. Tesco Corporation of Calgary acquired patent rights to casing drilling technology in 1995. The company now offers a conversion kit for existing drill rigs as well a new compact casing drilling rig for shallow markets. The single derrick will be rated at 1,500 meters, but initially it will be used to drill 700-800 meter gas wells in southeast Alberta. Some cost savings will be realized at these shallow depths, but the real cost saving advantages will be realized on deep holes. In the meantime, improvements are planned to the cutting structures of the under-rimming bit to increase safety and withstand higher torque loads. It will be also necessary to adapt techniques such as directional drilling and logging to the casing drilling conveyance mechanism which has been only partially successful thus far, especially in the retrieving mode. Another challenge already met, involved ensuring that casing could be run in high-compression loads without damage to connections. Despite these problems, the system attracted considerable attention with several international companies placing orders for immediate delivery. Another system, this one developed by Sperry-Sun Drilling Services and known as a 'casing while drilling' (CWD) system, is strictly a downhole assembly and is targeted for offshore use and deeper vertical holes. This system is currently being tested in two commercial operations in offshore Indonesia for Unocal Corporation. Despite numerous problems to fill casing with fluid during connections, penetration rates of 300-400 feet per hour were achieved.

Environmental assessment of exploration drilling off Nova Scotia: executive summary

International Nuclear Information System (INIS)

2000-01-01

The environmental assessment project of drilling offshore Nova Scotia covers year-around drilling conducted from jackup rigs, semi-submersible rigs, and drill ships that use the methods described in the project description on the Scotian Shelf, the Laurentian Channel and St, Pierre Bank. The assessment was sponsored by all the oil companies active in the area, namely Mobil Oil Canada, Shell Canada, Imperial Oil Resources, Gulf Canada Resources, Chevron Canada Resources, PanCanadian Petroleum, Murphy Oil Company and Norsk Hydro Canada Oil and Gas. This summary describes the impact assessment methodology used, provides a description of the project, reviews the cumulative impact, and the impacts of discrete activities such as noise and disturbances, operational discharges of oil, disruption of the benthos, garbage and waste disposal, and accidental oil spills, and outlines mitigation and monitoring activities to deal with the impacts. Mitigation measures encompass routine discharges, accidental oil spills, spill response, monitoring activities, contingency plans and an overall environmental protection plan. In addition to this generic assessment, the consultants recommend that individual exploration drilling programs that fall outside of the parameters outlined in the generic environmental assessment document, be required to undergo a program-specific assessment that focuses on those aspects of the proposed program that differ from the parameters prescribed in the present document. 9 refs

MONDO Project: real time ocean monitoring through Lagrangian drifters during offshore drilling operations

Energy Technology Data Exchange (ETDEWEB)

Mafra, Tatiana [Eni Oil do Brasil, Rio de Janeiro, RJ (Brazil); Fragoso, Mauricio da Rocha; Santos, Francisco Alves dos; Cruz, Leonardo M. Marques A.; Pellegrini, Julio A.C.; Cerrone, Bruna Nogueira [Prooceano, Rio de Janeiro, RJ (Brazil); Assireu, Arcilan Trevenzoli [Instituto Nacional de Pesquisas Espaciais (INPE), Sao Jose dos Campos, SP (Brazil)

2008-07-01

Monitoring the ocean conditions during offshore operations is essential for both operational and environmental aspects. Environmentally, not only to know better the environment where the activity is taking place, but also to be able to provide fast and accurate response in case of accidents. MONDO Project (Monitoring by Ocean Drifters) is a pioneer initiative from ENI Oil do Brasil and PROOCEANO that aimed to monitor currents as a part of a metoceanographic data monitoring project of drilling operations in Brazilian Waters, in Santos Basin throughout September to November 2007, 40 satellite tracked ocean drifters were deployed will be transmitting data up to November 2008. The results of this project can be used to study a wide range of subjects about ocean dynamics. Following the principles of social and environmental responsibility, MONDO Project aims to benefit the local ecosystem in increasing the scientific knowledge of the area to calibrate hydrodynamic models that will lead to more accurate modeling results and, as a consequence, to a better management of contingency plans. Based on these principles, the project will also provide unrestricted access to oceanographic data even after the end of operations. (author)

Review of ExxonMobil Canada's 2008 offshore environmental effects monitoring report

Energy Technology Data Exchange (ETDEWEB)

Cogswell, A.; Kenchington, E.; Kennedy, E.; Law, B.; Lee, K.; Tremblay, J.; Worcester, T. [Department of Fisheries and Oceans Canada, Dartmouth, NS (Canada). Maritimes Science; Courtenay, S. [Department of Fisheries and Oceans Canada, Moncton, NB (Canada). Gulf Science; Payne, J. [Department of Fisheries and Oceans Canada, St. John' s, NL (Canada). Newfoundland and Labrador Science

2009-07-15

The environmental effects monitoring (EEM) program for the Sable Offshore Energy Project (SOEP) was designed to evaluate predictions made during its environmental assessment (EA) process. The Oceans, Habitat, and Species at Risk Branch of the Department of Fisheries and Oceans Canada was asked to review ExxonMobil Canada Properties Inc.'s 2008 annual report regarding the EEM for this offshore project. This report reviewed the monitoring results for benthic habitat and fish density; produced water chemistry and toxicity; and mussel hydrocarbon body burden. This report revealed that SOEP's 2008 EEM was consistent with previous reports, but that the monitoring methods used were not particularly meaningful, particularly since they failed to address fish health and fish quality issues. 3 refs.

A Graphical Adversarial Risk Analysis Model for Oil and Gas Drilling Cybersecurity

OpenAIRE

Vieira, Aitor Couce; Houmb, Siv Hilde; Insua, David Rios

2014-01-01

Oil and gas drilling is based, increasingly, on operational technology, whose cybersecurity is complicated by several challenges. We propose a graphical model for cybersecurity risk assessment based on Adversarial Risk Analysis to face those challenges. We also provide an example of the model in the context of an offshore drilling rig. The proposed model provides a more formal and comprehensive analysis of risks, still using the standard business language based on decisions, risks, and value.

Casing drilling

Energy Technology Data Exchange (ETDEWEB)

Heenan, D. [Tesco Corp., Calgary, AB (Canada)

2003-07-01

This paper reviewed the experience that Tesco has gained by drilling several wells using only casings as the drill stem. Tesco has manufactured a mobile and compact hydraulic drilling rig called the Casing Drilling {sup TM} system. The system could be very effective and efficient for exploration and development of coalbed methane (CBM) reserves which typically require extensive coring. Continuous coring while drilling ahead, along wire line retrieval, can offer time savings and quick core recovery of large diameter core which is typically required for exploration core desorption tests. The proposed system may also have the potential to core or drill typically tight gas sands or underbalanced wells with air or foam. This would reduce drilling fluid damage while simultaneously finding gas. Compared to conventional drill pipes, Casing Drilling {sup TM} could also be effective with water production from shallow sands because of the smaller annual clearance which requires less air volumes to lift any produced water. 9 figs.

Canada's east coast offshore oil and gas industry: a backgrounder

International Nuclear Information System (INIS)

Bott, R.

1999-06-01

Another of the backgrounder series published by the Petroleum Communication Foundation, this booklet describes Canada's offshore oil and natural gas operations in the North Atlantic Ocean, specifically in the Hibernia (off Newfoundland, crude oil), Terra Nova (off Newfoundland, crude oil), Cohasset-Panuke (off Nova Scotia, crude oil) and Sable Island (off Nova Scotia, natural gas) fields. Together, these project represent an investment of more than 10 billion dollars and constitute a growing portion of Canada's 400,000 cubic metres of crude oil and natural gas liquids per day production. The booklet explains the importance of the offshore oil and natural gas industry to Canada, the benefits accruing to the maritime provinces locally, prospects for future offshore oil and natural gas development and provides a brief summary of each of the four current major projects. The booklet also provides an overview of the facilities required for offshore energy projects, environmental impacts and safeguards, exploration, drilling, production, processing and transportation aspects of offshore oil and gas projects. 9 refs, photos

A Graphical Adversarial Risk Analysis Model for Oil and Gas Drilling Cybersecurity

Directory of Open Access Journals (Sweden)

Aitor Couce Vieira

2014-04-01

Full Text Available Oil and gas drilling is based, increasingly, on operational technology, whose cybersecurity is complicated by several challenges. We propose a graphical model for cybersecurity risk assessment based on Adversarial Risk Analysis to face those challenges. We also provide an example of the model in the context of an offshore drilling rig. The proposed model provides a more formal and comprehensive analysis of risks, still using the standard business language based on decisions, risks, and value.

Offshore 2010. Final report; Offshore 2010. Sluttrapport

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

An overview of the accomplishments of the various projects that have received support from the Norwegian Research Council's program 'Offshore 2010'. The following projects are presented, some have English and some Norwegian project names: 'Critical parameters influencing inhibitor performance in multiphase flow', 'Development of the drilling optimization simulator (DDS) and a totally integrated drilling optimization system', 'Produksjonsoptimalisering og automatisk styring av broenner og roerledninger (PETRONICS)', 'Termisk isolerte undervannsroer for sikring av broenntransport over store avstander', 'Utvikling av magnetisk frekvensformer for styring av store subsea pumper paa havdyp ned mot 4000 meter', 'Flerfase stroemningsmaaler for permanent nedihulls installasjon', 'Hastighetsmaaling i flerfase stroemning ved passiv akustikk', 'Oil/water seperation offshore: optimized flow- and seperation behavior', 'Stroemningshastighet', 'A rock mechanics based reservoir simulation', 'MultiTool fase 2 - et flerbruksverktoey for nedihulls applikasjoner', 'Utvikling av undervanns olje-i-vann monitor for kontinuerlig maaling av lave oljekonsentrasjoner basert paa TR-LIFS', 'Subsea multipath ultrasonic liquid flow meter', 'Fluid characterization at elevated pressures and temperatures (Flucha II)'. The two main goals for the research program are 1. The development of new technology and competency in the field of downhole- and subsea processing and multiphase transportation, and 2. Innovation and commercialisation in small and medium sized companies (less than 100 employees). Some details on the financing and results are included (ml)

Microcomputers take over in off-shore process

Energy Technology Data Exchange (ETDEWEB)

Claricoates, J

1978-10-01

The special capabilities and adaptability of microcomputers are typically demonstrated by the use of them on Mobil Exploration, Norway, Inc.'s Statfjord A Condeep platform. One of the unique features of offshore oil production is that so many different operations are conducted in a very confined space. On Statfjord A drilling, production, storage of crude oil, gas compression for sale or reinjection, custody transfer, generation and distribution of a significant amount of electric power, a hotel facility, and flight operations, all have to be accommodated and controlled. Superimposed on these are comprehensive fire detection and shutdown systems. In such a highly complex, densely packed, and highly interactive environment, a supervisory control and data acquisition system (SCADA) by providing coordinated and easily read displays, better records for alarm analysis, and possibly suggesting corrective action when a fault does occur, is an essential aid to an operator, whose decisions must always by correct.

Two-riser system improves drilling at Auger prospect

International Nuclear Information System (INIS)

Gonzalez, R.; Marsh, G.L.; Ritter, P.B.; Mendel, P.E.

1992-01-01

This paper reports on a two-rise system (TRS) for drilling deepwater development wells which eliminates some of the limitations of conventional subsea technology and allows flexibility in well programs. Shell Offshore Inc.'s deep exploratory wells in Garden Banks 426 and 471 have encountered drilling problems that were attributed to limitations in casing sizes imposed by conventional subsea drilling systems. These problems are not uncommon in exploratory deepwater, deep well drilling in the Gulf of Mexico. Reservoir depths of up to 19,500 ft true vertical depth (TVD) and 7-in. production casing requirements led to potentially troublesome and expensive well plans. Because of the constraints placed on the development drilling program by completion requirements and directional drilling, a two-riser system was designed and fabricated. Solving such significant drilling problems has reduced overall development costs

Stochastic programming of drilling rigs supplies; Programacao estocastica de suprimentos de sondas

Energy Technology Data Exchange (ETDEWEB)

Vieira, Bruno Ferreira; Ferreira Filho, Virgilio Jose Martins [Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE/UFRJ), RJ (Brazil)

2012-07-01

The goal of this work is to use techniques of stochastic programming to reduce logistic costs regarding offshore drilling rigs. This theme is of great interest to Brazilian oil industry since there is an increasing number of wells that need to be perforated so that Brazilian oil production can reach its expected growth over the next ten years (PETROBRAS in particular has an ambitious strategy in this respect). Proper treatment of the uncertainties involved in the deliveries of supplies to offshore drilling rigs is essential, namely, these uncertainties need to be included in the models used in logistic models. Delays in the deliveries of products such as chemicals, perforation fluids and tubes may force drilling rigs to stop their operations what highly increases costs. The daily hiring rates of drilling rigs represent the highest cost in the perforation and completion of a well. (author)

Theory and application of a measurement-while-drilling neutron porosity sensor

International Nuclear Information System (INIS)

Roesler, R.F.; Barnett, W.C.; Paske, W.C.

1987-01-01

The authors describe the first MWD compensated neutron porosity measurement service (CNO) which employs a dual-spaced, borehole-compensated detector system to measure neutron-capture gamma rays. CNO service, when combined with existing MWD gamma ray and resistivity services, provides the basic data necessary for calculation of water saturation from MWD logs, making it possible to replace wireline logs in many situations with resulting savings in both logging costs and associated rig time. This is particularly cost effective when drilling high angle offshore development wells and in other high cost development drilling

Applied mathematics. Careful studies of drill bits and drill pipes set vibrations; Mathematiques appliquees. Etudes approfondies des vibrations du trepan et du train de tiges

Energy Technology Data Exchange (ETDEWEB)

Mabile, C.; Rey Fabre, I.; Benjelloun-Touimi-Dabaghi, Z. [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

1997-04-01

During the rotary drilling, drill pipes and bits are submitted to physical stresses which are all the more important that the well is deep. The aim of the study is then to physically understand these phenomena in order to prevent the effects as the pre-wear, the rupture of the drill pipes or the destruction of the measure instruments used at the bottom during the drilling of the well. Computers are used to establish a mathematical model which correspond to reality and which should be directly used on offshore platforms. (O.M.)

Deep-Time drilling in the Australian Archean: the Agouron Institute geobiological drilling project. (Invited)

Science.gov (United States)

Buick, R.

2010-12-01

The Agouron Institute has sponsored deep-time drilling across the South African Archean-Proterozoic boundary, investigating the rise of oxygen over an onshore-offshore environmental transect. It is now supporting a drilling program in the Australian Archean of the Pilbara Craton, addressing a similar theme but with the added goal of resolving controversy over the age and origin of hydrocarbon biomarker molecules in ancient kerogenous shales. As these have been claimed to provide evidence for the evolution of oxygenic photosynthesis long before the rise of atmospheric oxygen to persistently high levels during the ~2.3 Ga “Great Oxidation Event”, their syngenesis with their host shales is thus of critical importance for the interpretation of Earth’s early oxygenation history. During the first drilling season, 3 holes were drilled using techniques and equipment to minimize organic geochemical contamination (new drill-string components cleaned before drilling potentially biomarker-bearing rocks, pre-contamination of drilling fluid with a synthetic organic compound of similar geochemical characteristics to biomarkers, sterile cutting and storage of samples immediately upon retrieval from the core-barrel). The initial hole was a blank control for organic geochemistry, drilled into rocks too metamorphosed to retain biomarker molecules. These rocks, cherts, carbonates and pelites of the 3.52 Ga Coucal Formation, Coonterunah Group, have been metamorphosed to upper greenschist facies at temperatures near 500°C and so should have had any ancient soluble hydrocarbons destroyed. However, because they contain both carbonate and organic carbon, these rocks can instead provide isotopic information about the earliest evolution of biological metabolism as they possess residues of both the reactant and product sides of the carbon-fixation reaction. The second hole sampled an on-shore section of carbonates and kerogenous shales in the ~2.65 Ga Carawine Dolomite and Lewin Shale

An evaluation of calculation procedures affecting the constituent factors of equivalent circulating density for drilling hydraulics

Energy Technology Data Exchange (ETDEWEB)

Bailey, William J.

1996-12-31

This Dr. ing. thesis covers a study of drilling hydraulics offshore. The purpose of drilling hydraulics is to provide information about downhole pressure, suitable surface pump rates, the quality of hole cleaning and optimum tripping speeds during drilling operations. Main fields covered are drilling hydraulics, fluid characterisation, pressure losses, and equivalent circulating density. 197 refs., 23 figs., 22 tabs.

An evaluation of calculation procedures affecting the constituent factors of equivalent circulating density for drilling hydraulics

Energy Technology Data Exchange (ETDEWEB)

Bailey, William J

1997-12-31

This Dr. ing. thesis covers a study of drilling hydraulics offshore. The purpose of drilling hydraulics is to provide information about downhole pressure, suitable surface pump rates, the quality of hole cleaning and optimum tripping speeds during drilling operations. Main fields covered are drilling hydraulics, fluid characterisation, pressure losses, and equivalent circulating density. 197 refs., 23 figs., 22 tabs.

Fishing activity near offshore pipelines, 2017

NARCIS (Netherlands)

Machiels, Marcel

2018-01-01

On the North Sea bottom lie numerous pipelines to link oil- or gas offshore drilling units, - platforms and processing stations on land. Although pipeline tubes are coated and covered with protective layers, the pipelines risk being damaged through man-made hazards like anchor dropping and fishing

Offshore Blowouts, Causes and Trends

Energy Technology Data Exchange (ETDEWEB)

Holand, P

1996-02-01

The main objective of this doctoral thesis was to establish an improved design basis for offshore installations with respect to blowout risk analyses. The following sub objectives are defined: (1) Establish an offshore blowout database suitable for risk analyses, (2) Compare the blowout risk related to loss of lives with the total offshore risk and risk in other industries, (3) Analyse blowouts with respect to parameters that are important to describe and quantify blowout risk that has been experienced to be able to answer several questions such as under what operations have blowouts occurred, direct causes, frequency of occurrence etc., (4) Analyse blowouts with respect to trends. The research strategy applied includes elements from both survey strategy and case study strategy. The data are systematized in the form of a new database developed from the MARINTEK database. Most blowouts in the analysed period occurred during drilling operations. Shallow gas blowouts were more frequent than deep blowouts and workover blowouts occurred more often than deep development drilling blowouts. Relatively few blowouts occurred during completion, wireline and normal production activities. No significant trend in blowout occurrences as a function of time could be observed, except for completion blowouts that showed a significantly decreasing trend. But there were trends regarding some important parameters for risk analyses, e.g. the ignition probability has decreased and diverter systems have improved. Only 3.5% of the fatalities occurred because of blowouts. 106 refs., 51 figs., 55 tabs.

An investigation of an evaluation of the environmental conditions in analyses of a guide pipe and moorings of a drilling ship when drilling at great sea depths, Part two

Energy Technology Data Exchange (ETDEWEB)

Hiroichi, H; Susumu, K; Tetsuo, M; Yasuhiko, M

1983-01-01

The application of the results of analysis of the behavior of an offshore guide pipe and a system of mooring for evaluating the critical environmental conditions in the real plane of drilling offshore wells in great water depths in the region of Miyakodzima oki and Omadedzaki oki is examined. The following criteria were used in designing the moorings and the offshore guide pipe for Miyakodzima-oki: the maximal linear stretching stress of the moorings must be less than or equal to one third the rupture strength, the maximal angle of phiim, the angle between the vertical line and the lower part of this pipe, equal to 4 degrees and the maximal stress in the guide pipe of less than 40 percent of the fluidity limit, in storm conditions these indicators must be one third the rupture strength, 10 degrees and 60 percent of the fluidity limit, respectively. Data are cited from an analysis of the guide pipe, the stress of the moorings and the equipment. The results of static and dynamic analyses of an offshore guide pipe in the conditions of the Miyakodzima oki sea are compared. It is shown that with drilling in waves with a height of 5.7 meters and a period of 8.7 seconds and a current rate of 1.5 to 2.6 meters per second the horizontal shift of the drilling ship relative to the preventers (Sbs) is 4 percent, the stretching tension of the guide pipe based on the static analysis is 93 megapascals and based on dynamic analysis (hereinafter indicated in parentheses) (93 megapascals), phiim of 3.44 degrees (3.7 degrees) and in storm conditions at a wave height of 1.42 and period of 13.8 seconds the stress of the guide pipe reaches 148 megapascals (150 megapascals) and phiim is 7.73 degrees (8.4 degrees). These data attest to the fact that the static and dynamic analysis produce approximately identical results.

Chemical and benthos data collected from CTD, bottle, and other instruments in the Chukchi Sea in 2009-2010 as part of the Chukchi Sea Offshore Monitoring in Drilling Area - Chemical and Benthos (COMIDA-CAB) project (NODC Accession 0095566)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This accession contains physical, chemical, and biological data collected during research cruises for the Chukchi Sea Offshore Monitoring in Drilling Area (Chemical...

Review of technology for Arctic offshore oil and gas recovery

Energy Technology Data Exchange (ETDEWEB)

Sackinger, W. M.

1980-08-01

The technical background briefing report is the first step in the preparation of a plan for engineering research oriented toward Arctic offshore oil and gas recovery. A five-year leasing schedule for the ice-prone waters of the Arctic offshore is presented, which also shows the projected dates of the lease sale for each area. The estimated peak production rates for these areas are given. There is considerable uncertainty for all these production estimates, since no exploratory drilling has yet taken place. A flow chart is presented which relates the special Arctic factors, such as ice and permafrost, to the normal petroleum production sequence. Some highlights from the chart and from the technical review are: (1) in many Arctic offshore locations the movement of sea ice causes major lateral forces on offshore structures, which are much greater than wave forces; (2) spray ice buildup on structures, ships and aircraft will be considerable, and must be prevented or accommodated with special designs; (3) the time available for summer exploratory drilling, and for deployment of permanent production structures, is limited by the return of the pack ice. This time may be extended by ice-breaking vessels in some cases; (4) during production, icebreaking workboats will service the offshore platforms in most areas throughout the year; (5) transportation of petroleum by icebreaking tankers from offshore tanker loading points is a highly probable situation, except in the Alaskan Beaufort; and (6) Arctic pipelines must contend with permafrost, making instrumentation necessary to detect subtle changes of the pipe before rupture occurs.

Development of a Mine Rescue Drilling System (MRDS)

Energy Technology Data Exchange (ETDEWEB)

Raymond, David W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gaither, Katherine N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Polsky, Yarom [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Knudsen, Steven D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Broome, Scott Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Su, Jiann-Cherng [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Blankenship, Douglas A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Costin, Laurence S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-06-01

Sandia National Laboratories (Sandia) has a long history in developing compact, mobile, very high-speed drilling systems and this technology could be applied to increasing the rate at which boreholes are drilled during a mine accident response. The present study reviews current technical approaches, primarily based on technology developed under other programs, analyzes mine rescue specific requirements to develop a conceptual mine rescue drilling approach, and finally, proposes development of a phased mine rescue drilling system (MRDS) that accomplishes (1) development of rapid drilling MRDS equipment; (2) structuring improved web communication through the Mine Safety & Health Administration (MSHA) web site; (3) development of an improved protocol for employment of existing drilling technology in emergencies; (4) deployment of advanced technologies to complement mine rescue drilling operations during emergency events; and (5) preliminary discussion of potential future technology development of specialized MRDS equipment. This phased approach allows for rapid fielding of a basic system for improved rescue drilling, with the ability to improve the system over time at a reasonable cost.

The offshore disposal of radioactive waste by drilled emplacement: A feasibility study

International Nuclear Information System (INIS)

Bury, M.R.C.

1985-01-01

This book is a report, based on a study by Taylor Woodrow Construction Limited, on the overall feasibility of the disposal of high-level radioactive waste in boreholes drilled deep into the ocean bed. The work comprises an engineering appraisal of the disposal process with a view to establishing technical and operational feasibility and providing overall cost information to enable an economic assessment to be made. Contents: Summary report; Reference criteria; Drilling operation; Transfer of radioactive waste, personnel and other supplies; Handling of radioactive waste on board; Lowering strings of canisters; Emplacement and backfilling of canisters; Preliminary design of marine platform; Retrieval of flasks or canisters lost or misplaced; Variations to the features of the lowering system; Logistics of the operation; Construction cost estimate; Operational costs; Appendix

DALI - drilling advisor with logic interpretations: methodological issues for designing underbalanced drilling operations. Improving efficiency using case-based reasonic

Energy Technology Data Exchange (ETDEWEB)

Santana, Gustavo A.; Velazquez C, David [Mexican Oil Institute, Mexico DF (Mexico)

2004-07-01

A system that applies a method of knowledge-intensive case-based reasoning, for repair and prevention of unwanted events in the domain of offshore oil well drilling, has been developed in cooperation with an oil company. From several reoccurring problems during oil well drilling the problem of 'lost circulation', i.e. loss of circulating drilling fluid into the geological formation, was picked out as a pilot problem. An extensive general knowledge model was developed for the domain of oil well drilling. Different cases were created on the basis of information from one Mexican Gulf operator. When the completed CBR-system was tested against a new case, cases with descending similarity were selected by the tool. In an informal evaluation, the two best fitting cases proved to give the operator valuable advise on how to go about solving the new case (author)

A database of archived drilling records of the drill cuttings piles at the North West Hutton oil platform

International Nuclear Information System (INIS)

Marsh, Roy

2003-01-01

Drill cuttings piles are found underneath several hundred oil platforms in the North Sea, and are contaminated with hydrocarbons and chemical products. This study characterised the environmental risk posed by the cuttings pile at the North West Hutton (NWH) oil platform. Data on the drilling fluids and chemical products used over the platform's drilling history were transferred from archived well reports into a custom database, to which were added toxicological and safety data. Although the database contained many gaps, it established that only seven chemical products used at NWH were not in the lowest category of the Offshore Chemicals Notification Scheme, and were used in only small quantities. The study therefore supports the view that the main environmental risk posed by cuttings piles comes from hydrocarbon contamination. The (dated) well records could help future core sampling to be targeted at specific locations in the cuttings piles. Data from many platforms could also be pooled to determine generic 'discharge profiles.' Future study would benefit from the existence, in the public domain, of a standardised, 'legacy' database of chemical products

NMR of geophysical drill cores with a mobile Halbach scanner

International Nuclear Information System (INIS)

Talnishnikh, E.

2007-01-01

This thesis is devoted to a mobile NMR with an improved Halbach scanner. This is a lightweight tube-shaped magnet with sensitive volume larger and a homogeneity of the magnetic field higher than the previous prototype version. The improved Halbach scanner is used for analysis of water-saturated drill cores and plugs with diameters up to 60 mm. To provide the analysis, the standard 1D technique with the CPMG sequence as well as 2D correlation experiments were successfully applied and adapted to study properties of fluid-saturated sediments. Afterwards the Halbach scanner was calibrated to fast non-destructive measurements of porosity, relaxation time distributions, and estimation of permeability. These properties can be calculated directly from the NMR data using the developed methodology. Any independent measurements of these properties with other methods are not needed. One of the main results of this work is the development of a new NMR on-line core scanner for measurements of porosity in long cylindrical and semi cylindrical drill cores. Also dedicated software was written to operate the NMR on-line core scanner. The physical background of this work is the study of the diffusion influence on transverse relaxation. The diffusion effect in the presence of internal gradients in porous media was probed by 1D and 2D experiments. The transverse relaxation time distributions obtained from 1D and from 2D experiments are comparable but different in fine details. Two new methodologies were developed based on the results of this study. First is the methodology quantifying the influence of diffusion in the internal gradients of water-saturated sediments on transverse relaxation from 2D correlation experiments. The second one is the correction of the permeability estimation from the NMR data taking in account the influence of the diffusion. Furthermore, PFG NMR technique was used to study restricted diffusion in the same kind of samples. Preliminary results are reported

NMR of geophysical drill cores with a mobile Halbach scanner

Energy Technology Data Exchange (ETDEWEB)

Talnishnikh, E.

2007-08-21

This thesis is devoted to a mobile NMR with an improved Halbach scanner. This is a lightweight tube-shaped magnet with sensitive volume larger and a homogeneity of the magnetic field higher than the previous prototype version. The improved Halbach scanner is used for analysis of water-saturated drill cores and plugs with diameters up to 60 mm. To provide the analysis, the standard 1D technique with the CPMG sequence as well as 2D correlation experiments were successfully applied and adapted to study properties of fluid-saturated sediments. Afterwards the Halbach scanner was calibrated to fast non-destructive measurements of porosity, relaxation time distributions, and estimation of permeability. These properties can be calculated directly from the NMR data using the developed methodology. Any independent measurements of these properties with other methods are not needed. One of the main results of this work is the development of a new NMR on-line core scanner for measurements of porosity in long cylindrical and semi cylindrical drill cores. Also dedicated software was written to operate the NMR on-line core scanner. The physical background of this work is the study of the diffusion influence on transverse relaxation. The diffusion effect in the presence of internal gradients in porous media was probed by 1D and 2D experiments. The transverse relaxation time distributions obtained from 1D and from 2D experiments are comparable but different in fine details. Two new methodologies were developed based on the results of this study. First is the methodology quantifying the influence of diffusion in the internal gradients of water-saturated sediments on transverse relaxation from 2D correlation experiments. The second one is the correction of the permeability estimation from the NMR data taking in account the influence of the diffusion. Furthermore, PFG NMR technique was used to study restricted diffusion in the same kind of samples. Preliminary results are reported

Drilling rig

Energy Technology Data Exchange (ETDEWEB)

Galiopa, A A; Yegorov, E K

1981-01-04

A drilling rig is proposed which contains a tower, lifter in the form of n infinite chain, and mobile rotator with holding device connected to the chain, and pipe holder. In order to accelerate the auxiliary operations to move the drilling string and unloaded rotator, the rotator is equipped with a clamp with means for transverse connection of it to both branches of the chain, while the pipe holders equipped with a clamp with means of connecting it to one of the branches of the chain.

Offshore wind farm Bockstigen - installation and operation experience

Energy Technology Data Exchange (ETDEWEB)

Lange, B [Risoe National Lab., Wind Energy and Atmospheric Physics Dept., Roskilde (Denmark); Aagaard, E; Andersen, P E; Moeller, A [Wind World af 1997 A/S, Noerresundby (Denmark); Niklasson, S; Wickman, A [Vindkompaniet, Degerhamn (Sweden)

1999-03-01

The first Swedish offshore wind farm Bockstigen is operating since March 1998 near the coast of Gotland. It was built as a demonstration project by the Swedish wind farm developer Vindkompaniet, the Danish wind turbine manufacturer Wind World and the British offshore construction company Seacore and partly funded under the EU-THERMIE program. Bockstigen is the fourth offshore wind farm world-wide. While at previous wind farms the main emphasis laid on the demonstration of the technical feasibility of offshore wind energy utilisation, Bockstigen was aimed at demonstrating its economic viability. A number of innovative concepts have been employed: Drilled monopile foundations were used to save costs. A new construction method has been applied making use of a jack-up barge. A new control system for the turbines and the whole wind farm was developed, which controls the maximum power output, the flicker and the reactive power consumption depending on online measurements of the actual grid state. These new developments have been implemented successfully. A substantial cost reduction compared to previous offshore projects could be achieved. (au)

Gela offshore field

Energy Technology Data Exchange (ETDEWEB)

Pagliughi, G

1965-06-01

The field of Gela, off the southern shore of Sicily, is the only producing offshore field in the Mediterranean. It produces from Triassic dolimite limestones of 434-m thickness, water level at -3517 m. It is a water-drive reservoir producing 10/sup 0/F API oil and has 79 wells, some of them on shore. Most offshore wells are directional wells from shore; there are also 2 fixed platforms and a special mobile platform. The wells are on pump (stroke, 72 in.; capacity 200 tons per day). The crude goes directly to a combination refinery-petrochemical complex at Gela.

Development and Manufacture of Cost-Effective Composite Drill Pipe

Energy Technology Data Exchange (ETDEWEB)

James C. Leslie

2008-12-31

Advanced Composite Products and Technology, Inc. (ACPT) has developed composite drill pipe (CDP) that matches the structural and strength properties of steel drill pipe, but weighs less than 50 percent of its steel counterpart. Funding for the multiyear research and development of CDP was provided by the U.S. Department of Energy Office of Fossil Energy through the Natural Gas and Oil Projects Management Division at the National Energy Technology Laboratory (NETL). Composite materials made of carbon fibers and epoxy resin offer mechanical properties comparable to steel at less than half the weight. Composite drill pipe consists of a composite material tube with standard drill pipe steel box and pin connections. Unlike metal drill pipe, composite drill pipe can be easily designed, ordered, and produced to meet specific requirements for specific applications. Because it uses standard joint connectors, CDP can be used in lieu of any part of or for the entire steel drill pipe section. For low curvature extended reach, deep directional drilling, or ultra deep onshore or offshore drilling, the increased strength to weight ratio of CDP will increase the limits in all three drilling applications. Deceased weight will reduce hauling costs and increase the amount of drill pipe allowed on offshore platforms. In extreme extended reach areas and high-angle directional drilling, drilling limits are associated with both high angle (fatigue) and frictional effects resulting from the combination of high angle curvature and/or total weight. The radius of curvature for a hole as small as 40 feet (12.2 meters) or a build rate of 140 degrees per 100 feet is within the fatigue limits of specially designed CDP. Other properties that can be incorporated into the design and manufacture of composite drill pipe and make it attractive for specific applications are corrosion resistance, non-magnetic intervals, and abrasion resistance coatings. Since CDP has little or no electromagnetic force

Potential environmental benefits from regulatory consideration of synthetic drilling muds

International Nuclear Information System (INIS)

Burke, C.J.; Veil, J.A.

1995-02-01

When drilling exploration and production wells for oil and gas, drillers use specialized drilling fluids, referred to as muds, to help maintain well control and to remove drill cuttings from the hole. Historically, either water-based muds (WBMs) or oil-based muds (OBMs) have been used for offshore wells. Recently, in response to US Environmental Protection Agency (EPA) regulations and drilling-waste discharge requirements imposed by North Sea nations, the drilling industry has developed several types of synthetic-based muds (SBMs) that combine the desirable operating qualities of OBMs with the lower toxicity and environmental impact qualities of WBMs. This report describes the operational, environmental, and economic features of all three types of muds and discusses potential EPA regulatory barriers to wider use of SBMs

30 CFR 253.3 - How are the terms used in this regulation defined?

Science.gov (United States)

2010-07-01

... in this regulation defined? Terms used in this part have the following meaning: Advertise means... well drilled from a mobile offshore drilling unit (MODU) and the associated riser and well control...

Environmental perspectives on the East Coast offshore oil and gas industry

International Nuclear Information System (INIS)

Taylor, D.G.

2001-01-01

In this presentation, the author examined the environmental aspects affecting the offshore oil and gas development on the East Coast of Canada. Selected topics were covered to highlight what has been accomplished and the goals for the future in terms of the environment. The development of the oil and gas industry in the region has really taken off in the past twenty years, suffering from growing pains and enduring myths. An oil and gas project begins with seismic surveys, followed by exploratory wells being drilled, then proceeding to the construction and installation of the drilling production facilities, the production phase and the decommissioning of the facilities at the end of the useful life. Each phase of a project was reviewed and environmental concerns identified. Specific topics were addressed, such as drill cuttings, produced water, flaring, and decommissioning and abandonment. Selected problems were examined, notably fish and oil, spills, cumulative effects, the Oceans Act, and the regulatory evolution in the East Coast offshore. 9 refs., 1 tab., 1 fig

The Swedish Deep Drilling Program - an emerging scientific drilling program and new infrastructure.

Science.gov (United States)

Lorenz, Henning; Juhlin, Christopher

2010-05-01

Scientific drilling projects imply numerous aspects that are difficult to handle for individual research groups. Therefore, about three years ago a joint effort was launched in the Swedish geoscientific community to establish a national program for scientific drilling, the Swedish Deep Drilling Program (SDDP). Soon afterwards, several working groups established drilling proposals with Nordic and, also, international participation. With this serious interest in scientific drilling SDDP was able to successfully promote the Swedish membership in ICDP which commenced in 2008. Two SDDP projects achieved workshop grants from the International Continental Scientific Drilling Program (ICDP) in 2009. In the same year the Swedish Research Council decided to support an application for a truck-mounted drill rig - a big success for the SDDP working group. Scientific Drilling infrastructure: SDDP envisages a mobile platform that is capable of core drilling to at least 2500 m depth. The procurement will be made during 2010 and first operations are planned for 2011. This drill rig is primarily intended for use in the SDDP drilling projects, but will be rented out to other scientific drilling projects or even commercial enterprises in the remaining time to cover maintenance and future upgrade costs. SDDP's drill rig will be unique in Europe and complementary to the deep drilling InnovaRig of the GFZ German Research Centre for Geosciences. Until now, drilling to 2000 - 3000 m implied the use of a full-sized drill rig like the InnovaRig or the mobilization of a core drill rig from another continent. This gap will now be filled by Sweden's upcoming scientific drilling infrastructure. Drilling projects and proposals: Presently, SDDP serves six projects: "Collisional Orogeny in the Scandinavian Caledonides" (COSC; ICDP workshop spring 2010), the "Postglacial Fault Drilling Project" (PFDP; ICDP workshop autumn 2010), a "Deep Rock Laboratory" (DRL), "Palaeoproterozoic Mineralized Volcanic

SMART MONITORING AND DECISION MAKING FOR REGULATING ANNULUS BOTTOM HOLE PRESSURE WHILE DRILLING OIL WELLS

Directory of Open Access Journals (Sweden)

M. P. Vega

Full Text Available Abstract Real time measurements and development of sensor technology are research issues associated with robustness and safety during oil well drilling operations, making feasible the diagnosis of problems and the development of a regulatory strategy. The major objective of this paper is to use an experimental plant and also field data, collected from a basin operation, offshore Brazil, for implementing smart monitoring and decision making, in order to assure drilling inside operational window, despite the commonly observed disturbances that produce fluctuations in the well annulus bottom hole pressure. Using real time measurements, the performance of a continuous automated drilling unit is analyzed under a scenario of varying levels of rate of penetration; aiming pressure set point tracking (inside the operational drilling window and also rejecting kick, a phenomenon that occurs when the annulus bottom hole pressure is inferior to the porous pressure, producing the migration of reservoir fluids into the annulus region. Finally, an empirical model was built, using real experimental data from offshore Brazil basins, enabling diagnosing and regulating a real drilling site by employing classic and advanced control strategies.

Development of controlled drilling system

International Nuclear Information System (INIS)

Kiho, Kenzo; Miyakawa, Kimio; Suzuki, Koichi; Sunaga, Takayuki

2008-01-01

In Japan, the soft sedimentary rock of the Neogene tertiary is being focused as a host rock for the High Level Radioactive Waste (HLW) disposal. Especially, the soft sedimentary rock at the offshore, region is thought to be one of the best candidates, since there is no driving force of the underground water. The measurement and logging in the bore hole in order to check the hydro-geological and geomechanical conditions of the host rock is a very important way to examine the potentially of the disposal candidates. The CRIEPI (Central Research Institute of Electric Power Industry) has been conducting the project about the controlled drilling technology and the measurement and logging technologies in its borehole. In 2000, as the beginning year of the project, we made the conceptual design of the drilling and measuring systems, and made key tools concerning each technology on an experimental basis. We have been developing sub tools constructing drilling and measuring systems since 2000, and applying these systems to the Horonobe site recent 5 years. We will briefly report the outline of the system and the results of drilling and measurement that were carried out at the Horonobe site. (author)

Economic environmental management of drilling operations

International Nuclear Information System (INIS)

Longwell, H.J.; Akers, T.J.

1992-01-01

This paper presents significant environmental and regulatory initiatives developed by Exxon's New Orleans Drilling Organization. Specifically, the paper will cover drilling waste minimization techniques and disposal options, recycling of drilling waste streams, and environmentally managed drilling location design considerations. The implementation of some of these initiatives at Exxon's Chalkley field land locations have resulted in a fifty percent reduction in drilling location waste management costs. Some of these same initiatives have been successfully applied to Exxon's barge drilling locations. For operations at the environmentally sensitive Mobile Bay, Exxon contracted with a local company and assisted in the development of an economically and environmentally superior drilling waste disposal and treatment system. In summary, it is possible for drilling operators to pro-actively manage escalating environmental and regulatory challenges through the implementation of economic and practical initiatives

Impacts on seafloor geology of drilling disturbance in shallow waters.

Science.gov (United States)

Corrêa, Iran C S; Toldo, Elírio E; Toledo, Felipe A L

2010-08-01

This paper describes the effects of drilling disturbance on the seafloor of the upper continental slope of the Campos Basin, Brazil, as a result of the project Environmental Monitoring of Offshore Drilling for Petroleum Exploration--MAPEM. Field sampling was carried out surrounding wells, operated by the company PETROBRAS, to compare sediment properties of the seafloor, including grain-size distribution, total organic carbon, and clay mineral composition, prior to drilling with samples obtained 3 and 22 months after drilling. The sampling grid used had 74 stations, 68 of which were located along 7 radials from the well up to a distance of 500 m. The other 6 stations were used as reference, and were located 2,500 m from the well. The results show no significant sedimentological variation in the area affected by drilling activity. The observed sedimentological changes include a fining of grain size, increase in total organic carbon, an increase in gibbsite, illite, and smectite, and a decrease in kaolinite after drilling took place.

Seabird data collected by the Grand Banks offshore hydrocarbon industry 1999-2002 : results, limitations and suggestions for improvement

International Nuclear Information System (INIS)

Baillie, S.M.; Robertson, G.J.; Wiese, F.K.

2005-01-01

Offshore oil operations attract and concentrate migratory seabirds through an artificially enhanced food supply and lights. In order to understand the vulnerability of seabirds near offshore oil facilities, the degree of association of seabirds with these sites must be determined. Offshore oil and gas exploration on Newfoundland's Grand Banks began in the early 1980s, with first oil produced in 1997 at the Hibernia fixed platform. Additional production followed in 2002 from the Terra Nova Floating Production Storage and Offloading Vessel. As the Grand Banks oil industry grows, seismic surveys continue to be conducted and an estimated 30,000 litres of crude oil and synthetic based drilling fluids have been spilled from exploration drilling, development drilling and production oil operations between 1997 and 2002. Most of the spills occurred in winter when the number of seabirds on the Grand Banks are highest and most vulnerable to oil pollution. This report presents an evaluation of the current Grand Banks offshore oil and gas development seabird monitoring programs. It focuses mostly on seabird monitoring on fixed platforms. The objective was to assess the scientific quality of seabird-related industry programs by compiling and summarizing all available spatial and temporal seabird abundance data and deck stranded birds associated with Grand Banks offshore oil platforms from 1997 to 2002. Data on seabird distributions at sea and stranded bird encounters was collected from 8 offshore hydrocarbon sites on the northeastern Grand Banks. It was recommended that a standardized seabird monitoring and observer training program for the offshore operations in the Grand Banks region be implemented. 43 refs., 5 tabs., 16 figs., 3 appendices

Techno-Economic Comparison of Onshore and Offshore Underground Coal Gasification End-Product Competitiveness

Directory of Open Access Journals (Sweden)

Natalie Christine Nakaten

2017-10-01

Full Text Available Underground Coal Gasification (UCG enables the utilisation of coal reserves that are currently not economically exploitable due to complex geological boundary conditions. Hereby, UCG produces a high-calorific synthesis gas that can be used for generation of electricity, fuels and chemical feedstock. The present study aims to identify economically competitive, site-specific end-use options for onshore and offshore produced UCG synthesis gas, taking into account the capture and storage (CCS and/or utilisation (CCU of resulting CO 2 . Modelling results show that boundary conditions that favour electricity, methanol and ammonia production expose low costs for air separation, high synthesis gas calorific values and H 2 /N 2 shares as well as low CO 2 portions of max. 10%. Hereby, a gasification agent ratio of more than 30% oxygen by volume is not favourable from economic and environmental viewpoints. Compared to the costs of an offshore platform with its technical equipment, offshore drilling costs are negligible. Thus, uncertainties related to parameters influenced by drilling costs are also negligible. In summary, techno-economic process modelling results reveal that scenarios with high CO 2 emissions are the most cost-intensive ones, offshore UCG-CCS/CCU costs are twice as high as the onshore ones, and yet all investigated scenarios except from offshore ammonia production are competitive on the European market.

U.S. Geological Survey program of offshore resource and geoenvironmental studies, Atlantic-Gulf of Mexico region, from September 1, 1976, to December 31, 1978

Science.gov (United States)

Folger, David W.; Needell, Sally W.

1983-01-01

acromagnetic data, and 39,000 km of gravity data, plus 10,000 samples and logs obtained from U.S. Geological Survey and industry drilling (for example, coreholes of the Atlantic Slope Program, Joint Oceanographic Institutions Deep Earth Sampling, Continental Offshore Stratigraphic Tests, and the Atlantic Margin Coring Program). A sedimentary section of Jurassic and Cretaceous age grades from terrigenous clastic rocks nearshore to carbonate rocks offshore; this section is part of an extensive buried bank-platform complex that could contain large reserves of natural gas and oil. The volume of sediment deposited offshore far exceeds the volume deposited onshore where extensive accumulations of oil, gas, and minerals have been found. Commercial exploratory drilling offshore thus far has been limited to the Baltimore Canyon Trough area off New Jersey, where at least two holes have found gas; leasing has taken place in the Southeast Georgia Embayment, where drilling was scheduled to begin in 1979, and is imminent in the Georges Bank area off New England. In addition, hydrogeologic and hydrochemical data obtained from the drilling studies have delineated freshwater-bearing submarine extensions of land aquifers that are important coastal ground-water resources. Hazards in the Georges Bank area include sand mobility associated with strong currents and storm-driven waves; high concentrations of suspended sediment in the water column that, when mixed with spilled oil, may sink to the bottom; and slumping along the upper slope. In the Baltimore Canyon, high sediment mobility accompanies major winter storms, and slumped material may cover as much as 20 percent of the upper slope. Potentially unstable slope areas are being studied in great detail to provide data on timing, triggering mechanisms, and rates of sediment movement. In the Southeast Georgia Embayment and Blake Plateau Basin, strong Gulf Stream flow poses a major problem to all offshore operations. In the Gulf o

Perturbation of seafloor bacterial community structure by drilling waste discharge.

Science.gov (United States)

Nguyen, Tan T; Cochrane, Sabine K J; Landfald, Bjarne

2018-04-01

Offshore drilling operations result in the generation of drill cuttings and localized smothering of the benthic habitats. This study explores bacterial community changes in the in the upper layers of the seafloor resulting from an exploratory drilling operation at 1400m water depth on the Barents Sea continental slope. Significant restructurings of the sediment microbiota were restricted to the sampling sites notably affected by the drilling waste discharge, i.e. at 30m and 50m distances from the drilling location, and to the upper 2cm of the seafloor. Three bacterial groups, the orders Clostridiales and Desulfuromonadales and the class Mollicutes, were almost exclusively confined to the upper two centimeters at 30m distance, thereby corroborating an observed increase in anaerobicity inflicted by the drilling waste deposition. The potential of these phylogenetic groups as microbial bioindicators of the spatial extent and persistence of drilling waste discharge should be further explored. Copyright © 2017 Elsevier Ltd. All rights reserved.

Feasibility study of electromechanical cylinder drivetrain for offshore mechatronic systems

DEFF Research Database (Denmark)

Hagen, D.; Pawlus, W.; Ebbesen, M. K.

2017-01-01

Currently, there is an increasing focus on the environmental impact and energy consumption of the oil and gas industry. In offshore drilling equipment, electric motors tend to replace traditionally used hydraulic motors, especially in rotational motion control applications. However, force densiti...

A cross-taxa study using environmental DNA/RNA metabarcoding to measure biological impacts of offshore oil and gas drilling and production operations

KAUST Repository

Laroche, Olivier

2017-12-01

Standardized ecosystem-based monitoring surveys are critical for providing information on marine ecosystem health. Environmental DNA/RNA (eDNA/eRNA) metabarcoding may facilitate such surveys by quickly and effectively characterizing multi-trophic levels. In this study, we assessed the suitability of eDNA/eRNA metabarcoding to evaluate changes in benthic assemblages of bacteria, Foraminifera and other eukaryotes along transects at three offshore oil and gas (O&G) drilling and production sites, and compared these to morphologically characterized macro-faunal assemblages. Bacterial communities were the most responsive to O&G activities, followed by Foraminifera, and macro-fauna (the latter assessed by morphology). The molecular approach enabled detection of hydrocarbon degrading taxa such as the bacteria Alcanivorax and Microbulbifer at petroleum impacted stations. Most identified indicator taxa, notably among macro-fauna, were highly specific to site conditions. Based on our results we suggest that eDNA/eRNA metabarcoding can be used as a stand-alone method for biodiversity assessment or as a complement to morphology-based monitoring approaches.

A cross-taxa study using environmental DNA/RNA metabarcoding to measure biological impacts of offshore oil and gas drilling and production operations

KAUST Repository

Laroche, Olivier; Wood, Susanna A.; Tremblay, Louis A.; Ellis, Joanne; Lear, Gavin; Pochon, Xavier

2017-01-01

Standardized ecosystem-based monitoring surveys are critical for providing information on marine ecosystem health. Environmental DNA/RNA (eDNA/eRNA) metabarcoding may facilitate such surveys by quickly and effectively characterizing multi-trophic levels. In this study, we assessed the suitability of eDNA/eRNA metabarcoding to evaluate changes in benthic assemblages of bacteria, Foraminifera and other eukaryotes along transects at three offshore oil and gas (O&G) drilling and production sites, and compared these to morphologically characterized macro-faunal assemblages. Bacterial communities were the most responsive to O&G activities, followed by Foraminifera, and macro-fauna (the latter assessed by morphology). The molecular approach enabled detection of hydrocarbon degrading taxa such as the bacteria Alcanivorax and Microbulbifer at petroleum impacted stations. Most identified indicator taxa, notably among macro-fauna, were highly specific to site conditions. Based on our results we suggest that eDNA/eRNA metabarcoding can be used as a stand-alone method for biodiversity assessment or as a complement to morphology-based monitoring approaches.

Casing drilling TM : a viable technology for coal bed methane?

Energy Technology Data Exchange (ETDEWEB)

Madell, G.; Muqeem, M. [Tesco Corp., Calgary, AB (Canada)

2001-07-01

This paper highlighted the experience that Tesco has gained by drilling more than 30 wells using only casings as the drill stem, suggesting that such technology could be advantageous for Coal Bed Methane (CBM) exploration and development. Tesco has manufactured a mobile and compact hydraulic drilling rig that is ideal to meet the great demand for CBM development in Canada. The Casing Drilling TM system, when used in conjunction with the drilling rig, could be very effective and efficient for exploration and development of CBM reserves which typically require extensive coring. Continuous coring while drilling ahead and wire line retrieval can offer time savings and quick core recovery of large diameter core required for exploration core desorption tests. The proposed system may also have the potential to core or drill typically tight gas sands or coal beds under balanced with air or foam. This would reduce drilling fluid damage while finding gas at the same time. Compared to conventional drill pipes, Casing Drilling TM could also be effective with water production from shallow sands because of the smaller annual clearance which requires less air volumes to lift any produced water. 8 refs., 3 tabs., 9 figs.

Optimizing drilling performance using a selected drilling fluid

Science.gov (United States)

Judzis, Arnis [Salt Lake City, UT; Black, Alan D [Coral Springs, FL; Green, Sidney J [Salt Lake City, UT; Robertson, Homer A [West Jordan, UT; Bland, Ronald G [Houston, TX; Curry, David Alexander [The Woodlands, TX; Ledgerwood, III, Leroy W.

2011-04-19

To improve drilling performance, a drilling fluid is selected based on one or more criteria and to have at least one target characteristic. Drilling equipment is used to drill a wellbore, and the selected drilling fluid is provided into the wellbore during drilling with the drilling equipment. The at least one target characteristic of the drilling fluid includes an ability of the drilling fluid to penetrate into formation cuttings during drilling to weaken the formation cuttings.

Simulated behavior of drilling fluid discharges off Southern California

International Nuclear Information System (INIS)

Brandsma, M.G.; Kolpack, R.L.; Dickey, T.D.; Balcom, B.J.

1990-01-01

This paper focuses on the computer-simulated short-term behavior of drilling-fluid solids from the time of release to initial deposition on the ocean bottom. The geographic areas of primary interest were the Santa Barbara Channel and Point Conception regions off southern California. Simulations (53) were conducted for water depths ranging from 30 to 750 m. Oceanographic parameters for several representative oceanic conditions were obtained from available field measurements in the area. Characteristics of representative drilling-fluid solids were formulated from information supplied by several offshore operators and by laboratory analyses of samples

Released geophysical and geological reports : Newfoundland offshore area September 2003

International Nuclear Information System (INIS)

2003-09-01

This two-part publication contains a list of geophysical and geological data acquired by the Canada-Newfoundland Offshore Petroleum Board (C-NOPB). It is made available to the public in accordance with a subsection of the Canada-Newfoundland Atlantic Accord Implementation Act which states that such data can be released five years after the date of completion of a program. The programs for which the data has been released are listed in chronological order by completion date. A list of wells drilled within the C-NOPB's jurisdictional area is also included along with a map showing the area of jurisdiction. The well data includes category 1 information from exploratory wells, delineation wells, and development wells. It includes factual data obtained directly from well drilling which must be made available for public examination 2 years after well completion. Category 1 data refers to drill cuttings, well fluid samples, open-hole logs, formation stimulation data, petroleum analyses, drill mud reports, and well site survey information. The interpretive geological and geophysical reports are based on industry data from exploratory programs conducted in the Newfoundland offshore area. They include information from synthetic seismograms, velocity surveys, vertical seismic profiles, petrological reports, geochemical reports, and cyberlook logs. The jurisdictional areas include Western Newfoundland, South Grand Banks, North Grand Banks, the Northeast Newfoundland Shelf, and the Labrador Shelf. Program numbers are coded to contain the geographic region to which the program relates, the type of proposed geophysical or geological work, the company operating the program, and the sequential number of that type of program operated by each company. 8 tabs

Trace metal distribution and mobility in drill cuttings and produced waters from Marcellus Shale gas extraction: Uranium, arsenic, barium

International Nuclear Information System (INIS)

Phan, Thai T.; Capo, Rosemary C.; Stewart, Brian W.; Graney, Joseph R.; Johnson, Jason D.; Sharma, Shikha; Toro, Jaime

2015-01-01

Highlights: • Distributions of U, As, and Ba in Marcellus Shale were determined. • As is primarily associated with sulfide minerals, Ba with exchange sites. • Most U is in the silicate minerals, but up to 20% is partitioned into carbonate. • Low [U] and [As] in produced water are consistent with reducing downhole conditions. • Proper waste management should account for potential mobilization of U and As. - Abstract: Development of unconventional shale gas wells can generate significant quantities of drilling waste, including trace metal-rich black shale from the lateral portion of the drillhole. We carried out sequential extractions on 15 samples of dry-drilled cuttings and core material from the gas-producing Middle Devonian Marcellus Shale and surrounding units to identify the host phases and evaluate the mobility of selected trace elements during cuttings disposal. Maximum whole rock concentrations of uranium (U), arsenic (As), and barium (Ba) were 47, 90, and 3333 mg kg −1 , respectively. Sequential chemical extractions suggest that although silicate minerals are the primary host for U, as much as 20% can be present in carbonate minerals. Up to 74% of the Ba in shale was extracted from exchangeable sites in the shale, while As is primarily associated with organic matter and sulfide minerals that could be mobilized by oxidation. For comparison, U and As concentrations were also measured in 43 produced water samples returned from Marcellus Shale gas wells. Low U concentrations in produced water (<0.084–3.26 μg L −1 ) are consistent with low-oxygen conditions in the wellbore, in which U would be in its reduced, immobile form. Arsenic was below detection in all produced water samples, which is also consistent with reducing conditions in the wellbore minimizing oxidation of As-bearing sulfide minerals. Geochemical modeling to determine mobility under surface storage and disposal conditions indicates that oxidation and/or dissolution of U

The development of Canadian leadership in horizontal drilling technology

Energy Technology Data Exchange (ETDEWEB)

Hawkins, J R

1989-01-01

Horizontal wells are of increasing interest in the oil and gas industry, as is evident from the increase in the numbers of such wells being drilled. Horizontal well technology is used to improve production rates, notably in low permeability formations; to capture reserves if a reservoir is not economic using non-horizontal wells; to manage breakthrough of sweep fluids and increase sweep efficiency; and to extend the areal reach from a single surface location, especially in offshore production. The types of horizontal wells, differentiated on the basis of how quickly the well becomes horizontal, are briefly outlined and a short history of horizontal wells is presented. Canadian accomplishments in this field are then described, including steerable drilling systems, measurement-while-drilling systems, management of hole drag and torque, and well completion techniques. About 25 horizontal wells are forecast to be drilled in Canada in 1989, indicating the favorable future of this technology. 2 figs., 5 tabs.

Metre by metre: Advances in drilling technology are unlocking the doors to stubborn reserves

Energy Technology Data Exchange (ETDEWEB)

Jaremko, D.

2004-03-01

Advances in drilling technology such as horizontal drilling, controlled pressure drilling, underbalanced or reduced overbalanced drilling, steam assisted cavity drainage, the modified magnetic ranging system and a growing arsenal of on-line controls such as measurement-while drilling (MWD) and logging-while-drilling (LWD) are constantly enlarging the sites to which operators can go, the range of the pay zone that they can conquer, and to design increasingly site-specific approaches to deal with the change of formation characteristics from location to location. This article provides an overview of recent advances, focusing on underbalanced, balanced and reduced overbalanced drilling, and latest versions of data acquisition systems such as MWD and LWD which are capable of operating at twice the speed of conventional systems and provide accurate data even under the extremely difficult conditions found in hostile offshore environment.

Rapid Development of Drilling Technology and Market of China

Institute of Scientific and Technical Information of China (English)

Wang Guanqing; Ni Rongfu

1994-01-01

@@ China's developing drilling market Now, CNPC is the owner of more than 1 000 rigs of large and medium size, including imported electric-drive rigs with 6 000 to 9 000 m drilling capacity, imported mechanical drive rigs with 5 000 to 6 000 m drilling capacity, imported mobile rigs with 1 500 to 3 000 m drilling capacity and a lot of home-made mechanical rigs with 2 000,3 200, 4 500 and 6 000m drilling capacity, which can meet the requirement of the domestic and foreign drilling market.

Developments in offshore technology. Entwicklungen in der Offshoretechnik

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This book contains the summarized lectures held on the 8th of October, 1981 within the first status Seminar 'Offshore technology' which was organized by the Federal Minstry for Research and Technology. Contents are divided into: 1. Offshore-natural gas liquefaction, conveying systems. Offshore-tanker charging with supercold liquiefied gases; development of LNG-offshore - convayance systems; 2.) Development of components and installations in offshore structures: mooving-measuring- and monitoring systems for the installation of the EPOS deck; underwater-piling with a hydraulic-pile hammer; cast steel nodes for offshore-structures (material, calculation, design); 3.) underwater tools: the underwater-working system SUPRA; test results and experience with the unmanned UW-instrument-carrier FUGE; development of a mobile diver assistance vehicle for inspection and maintenance duties; 4.) underwater-pipeline-technique: flexible offshore-pipeline/continuous production and assembly, pipeline assembly at sea according to the J-Method with flash-welding technique; construction and testing of UWAG I (underwater working device) for embedding cables and pipes in the ocean soil.

Impact of exploratory offshore drilling on benthic communities in the Minerva gas field, Port Campbell, Australia

Energy Technology Data Exchange (ETDEWEB)

Currie, D.R.; Isaacs, L.R. [Central Queensland Univ., Gladstone (Australia). Centre for Environmental Management

2005-04-01

Changes to benthic infauna caused by exploratory gas drilling operations in the Minerva field were examined experimentally using a BACI (before, after, control, impact) design. Analysis of 72 x 0.1 m{sup 2} Smith-McIntyre grab samples obtained from one pre-drilling and three post-drilling periods yielded a diverse fauna consisting of 196 invertebrate species and 5035 individuals. Changes to benthic community structure were assessed using ANOVA and nonmetric multidimensional scaling (MDS). The abundances of two common species (Apseudes sp. 1 and Prionospio coorilla) decreased significantly at the well-head site immediately after drilling. The size of these reductions in abundance ranged between 71% and 88%, and persisted for less than 4 months after drilling. A third common species (Katlysia sp. 1) increased in abundance 200 m east of the well-head following drilling. Most species occurred at densities too low to be analysed individually and so were pooled at higher taxonomic levels. Changes in the abundance of species aggregated by phylum varied, but significant declines in the most abundant phyla (Crustaceans and Polychaetes) of 45-73% were observed at all sites within a 100 m radius of the well-head following drilling. In most cases these changes became undetectable four months after drilling following species recruitments. MDS ordinations confirm that drilling related changes to benthic community structure are most pronounced at stations located closest to the well-head. Additionally, the ordinations indicate that modified communities persist at the well-head for more than 11 months following exploratory drilling. (author)

Petroleum drilling and production operations in the Gulf of Mexico

International Nuclear Information System (INIS)

Fang, C.S.

1991-01-01

Decades of offshore and inland petroleum drilling and production in the Gulf of Mexico and on the Gulf Coast have provided the much needed energy and chemical feedstocks to the nation, and also have made an impact on the environment in the area. Our study showed deposits of contaminated sediment on the ocean floor around offshore platforms, old reserve pits, and dump sites next to many surface facilities and compressor stations. The substances found on the ocean floor and in dump sites are simple or emulsified mixtures of silt, hydrocarbons, and water. The cleaning of the ocean floor and pits is an economic and technical challenge. Hydrocarbons are from crude oil and chemical additions fro various operational necessities, including additions of biocides, corrosion inhibitors, antifreezes, and coagulants. When the new government regulations lower the allowable maximum total organic carbon level to the 50 ppm range, these hydrocarbons can no longer be ignored by drilling and production operators

Speeding up : new Atlas Copco rig meant to cut non-drilling time

Energy Technology Data Exchange (ETDEWEB)

Roche, P.

2009-06-15

Automation has significantly reduced the time needed to drill shallow to medium-depth wells. The time it takes for a drill to reach the production zone is decreasing because newly developed hydraulic systems are able to maintain a constant pace. However, a great deal of time is still consumed by demobilization, transportation and setting up to drill the next well. Atlas Copco Drilling Solutions, a Swedish-based global maker of industrial equipment such as mining and mineral exploration rigs, designed a new Predator drilling system that consists of a mobile rig, a substructure and a pipe-handling skate. The Predator drilling system reduces non-drilling time and the associated costs. This article described the design of this new drilling system with particular reference to how it combines the mobile rig, the substructure and the pipe-handling skate into a three-load package. In order to reduce rig weight and improve mobility, the system is designed so that the table, master bushing, hydraulic slips and iron roughneck are part of the substructure that travel together. The rig has a working hook load capacity of 200,000 pounds, translating into a nominal depth capacity of 8,000 to 10,000 feet. The article also described the mounting of the rig, maneuverability, hydraulic control, and pipe-handling safety. Its various components were also described. 1 ref., 1 fig.

A feasibility study of the disposal of radioactive waste in deep ocean sediments by drilled emplacement

International Nuclear Information System (INIS)

Bury, M.R.C.

1983-08-01

This report describes the second phase of a study of the feasibility of disposal and isolation of high level radioactive waste in holes drilled deep into the sediments of the ocean. In this phase, work has concentrated on establishing the state of the art of the various operations and developing the design, in particular the drilling operation, the loading of flasks containing waste canisters from supply vessels onto the platform, the handling of radioactive waste on board, and its emplacement into predrilled holes. In addition, an outline design of the offshore platform has been prepared. (author)

Georges Bank drilling moratorium gets extended until 2015

Energy Technology Data Exchange (ETDEWEB)

Anon.

2010-07-15

A moratorium on oil and gas exploration and drilling on the Georges Bank will continue until the end of 2015. Governments require a full public review and research concerning the potential environmental impacts of the project before lifting the moratorium. Canada's federal and provincial governments have agreed to gather information related to the region's fragile ecosystem, and investigate the potential impacts that petroleum-related activities may have in the area. Preliminary reviews are being conducted to study the socio-economic impacts of offshore petroleum activities and to assess new technologies and drilling practices that may be used to reduce the impacts of oil and gas operations. 1 fig.

Western Newfoundland and Labrador offshore area strategic environmental assessment amendment

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-11-15

The Canada-Newfoundland and Labrador Offshore Petroleum Board issued a call for bids in May 2007 that included a piece of land in offshore western Newfoundland. This report presented an amendment to the 2005 western Newfoundland and Labrador offshore strategic environmental assessment (SEA) in order to extend the coverage of the previous piece of land and included additional lands southwest of the original SEA prepared in 2005. This report presented the objectives and purpose of the SEA amendment and the history of oil and gas activities in western Newfoundland and Labrador offshore area. It discussed the biological environment in terms of plankton; benthic invertebrates; fish and fisheries; marine-associated birds; marine mammals and sea turtles; species at risk; and potentially sensitive areas. Environmental effects of exploration and production activities were discussed in terms of sound; routine exploratory/delineation drilling and production activities; accidental events; and cumulative effects. Last, the report presented the conclusions including potential issues, data gaps, and planning considerations. It was concluded that petroleum exploration activity generally can proceed in the amendment area with the application of standard mitigation measures currently applied to offshore exploratory activities elsewhere in the Newfoundland offshore. 90 refs., 8 tabs., 18 figs., 1 appendix.

Western Newfoundland and Labrador offshore area strategic environmental assessment amendment

International Nuclear Information System (INIS)

2007-11-01

The Canada-Newfoundland and Labrador Offshore Petroleum Board issued a call for bids in May 2007 that included a piece of land in offshore western Newfoundland. This report presented an amendment to the 2005 western Newfoundland and Labrador offshore strategic environmental assessment (SEA) in order to extend the coverage of the previous piece of land and included additional lands southwest of the original SEA prepared in 2005. This report presented the objectives and purpose of the SEA amendment and the history of oil and gas activities in western Newfoundland and Labrador offshore area. It discussed the biological environment in terms of plankton; benthic invertebrates; fish and fisheries; marine-associated birds; marine mammals and sea turtles; species at risk; and potentially sensitive areas. Environmental effects of exploration and production activities were discussed in terms of sound; routine exploratory/delineation drilling and production activities; accidental events; and cumulative effects. Last, the report presented the conclusions including potential issues, data gaps, and planning considerations. It was concluded that petroleum exploration activity generally can proceed in the amendment area with the application of standard mitigation measures currently applied to offshore exploratory activities elsewhere in the Newfoundland offshore. 90 refs., 8 tabs., 18 figs., 1 appendix

Ergonomic exposure on a drilling rig

DEFF Research Database (Denmark)

Jensen, Carsten; Jensen, Chris

. In a relatively old study on American drilling rigs it was indicated that lower back problems was a frequent cause of absence (Clemmer et al. 1991). Most of the incidents causing lower back injuries were associated with heavy lifting or pushing/pulling objects by roustabouts, floorhands, derrickmen and welders......, but for some of the most frequent problems, such as musculoskeletal problems, it is difficult to determine whether the causes are work‐related or not. As manual handling (lifting, pushing, etc.) in awkward body postures increase the risk of developing musculoskeletal disorders, it should be expected that work......‐related health problems contribute to sickness absence in the offshore industry, if these working postures are common. However, also work‐related psychosocial factors, personal factors and other factors may contribute to the development of lower back disorders, which often have a multifactorial background...

Chemical monitoring of mud products on drilled cuttings

International Nuclear Information System (INIS)

Hughes, T.L.; Jones, T.G.J.; Tomkins, P.G.; Gilmour, A.; Houwen, O.H.; Sanders, M.

1991-01-01

An increasing area of concern for offshore drilling practices in the environmental impact of discharged drilled cuttings contaminated with drilling fluids. The standard retort analysis is of limited accuracy and chemical specificity. Anticipating future requirements for a more complete accounting of mud chemicals discharged to the environment, we present here results for chemical monitoring using a modern comprehensive chemical analysis technique. Fourier transform infrared (FT-IR) spectrometry. In this paper description is given of sampling methods found to be practical and the main calibration requirements are discussed. The techniques developed in the course of this work give a good mineralogical breakdown of mud solids (commercial and drilled solids) in addition to the environmentally relevant measurements relating to mud on cuttings. The possibility of using the new technique for the rigsite monitoring of drilling cuttings is demonstrated. Cuttings samples simultaneously from the flow line, shaker screen, desilter and mud cleaner were analyzed. It is found that mud polymers and other organic additives can be measured with sufficient accuracy to measure the removal of mud products by discharged cuttings. The technique is also applicable to quantify the losses of oil-based mud on cuttings. Field testing has shown that the instrumentation used in sufficiently robust and simple to use for rig-site application

Decision 99-28: Mobil Oil Canada, Ltd., and Mobil Resources Ltd., - application for a well licence to drill a critical sour gas well LSD 4-36-27-28 W4, Crossfield Field, application No. 1037560

International Nuclear Information System (INIS)

1999-01-01

On 12 February 1999, Mobil submitted Application No. 1037560 to the Alberta Energy and Utilities (EUB) Board on a routine basis, pursuant to Section 2.020 of the Oil and Gas Conservation Regulations, for a well licence to drill a critical sour gas well. The well would be drilled from a surface location in Legal Subdivision (LSD) 4 of Section 36, Township 27, Range 28, West of the 4th Meridian to a bottomhole location in LDS 7-36-27-28 W4M, with an 1100 m horizontal section. The aim of the 4-36 well was to obtain gas production from the Crossfield member. On 17 February 1999, the EUB issued Well Licence No. 221575 on the understanding that there were no outstanding objections to the 4-36 well. Mobil spudded the 4-36 well on 3 March 1999, drilled to 363 m and set surface casing. The EUB subsequently received objections to the application from area residents near the proposed well location. Accordingly, pursuant to Section 43 of the Energy Resources Conservation Act, the EUB directed that a public hearing be held to consider the application. The Board assessed in detail the effects that would likely result and the mitigative measures that would have to be taken to reduce any negative effects considering: the proposed well location, impacts of the proposed well, safety of the well, and public notification and consultation. Having carefully considered all the evidence, the EUB Board determined that Application No. 1037560 met all the EUB's regulatory requirements and was satisfied that appropriate measures were taken to ensure that public safety risks and impacts were minimized

Application of a new Magnetic Resonance Logging While Drilling Tool in Offshore Nigeria

International Nuclear Information System (INIS)

Kamal, O.; Adindu, F.; Anselm, O.; Bacon, R.; Butt, P.; Ogbuagu, C.

2003-01-01

This paper describes results gained during the running of a new NMR logging-while-drilling (LWD) tool that has ben designed to run in any By combining with core and magnetic resonance data, probabilistic mineral analysis (with ECS and NGT) showed that the sands with lowest feldspars have the highest permeability. These sands with large grain sizes were deposited in the high-energy upper shore-face environment

Comprehensive borehole management for shorter drilling time; Umfassendes Bohrfortschrittsmanagement zur Verkuerzung der Bohrprojektdauer

Energy Technology Data Exchange (ETDEWEB)

Roehrlich, M. [ExxonMobil Production Deutschland GmbH, Hannover (Germany)

2007-09-13

In 2006, the trademarked ExxonMobil Fast Drill Process (FDP) was introduced also in the German ExxonMobil boreholes. The process is to maximize the drilling speed for every meter drilled. The process makes it possible to ensure borehole management on the basis of quantitative data and in consideration of all phases that are relevant for sinking a borehole. The FDP is used world-wide in all ExxonMobil drilling departments. More than 1.35 million meters are drilled annually in many different boreholes with different geological conditions, drilling profiles and international sites. The results were similar in many cases, with a significant increase in ROP and drill bit life, and with less damage caused by vibrations. FDP was developed on the basis of real time monitoring of the specific mechanical energy (MSE) required for drilling. MSE monitoring was found to be an effective tool dor detecting inefficient functioning of the drill bit and the overall system. To make operation more efficient, the causes must be identified and measures must be taken accordingly, taking into account the potential risks involved in such measures. MSE monitoring is a tool while FDPL is a broad management process ensuring that MSE and many other data sources are used effectively for optimisation of the ROP. Consequent implementation of the process resulted in a significant increase of the ROP. The major elements required for achieving this goal are discussed. (orig.)

Canada-Nova Scotia Offshore Petroleum Board Annual report 1998-1999

International Nuclear Information System (INIS)

1999-01-01

The Canada-Nova Scotia Offshore Petroleum Board is responsible for ensuring safe working conditions for offshore petroleum activities, protecting the environment during offshore petroleum operations, and managing offshore petroleum resources. This annual report includes financial statements of the Board for the fiscal year ending March 31, 1999. The projects undertaken by the Board in 1998-1999 included a technical audit of the Sable Offshore Energy Project, a resource assessment of the area known as the 'Gully', and resolving a complication regarding publicly available resource data for calls for bids for NS98-1 and NS98-2. A list of exploration licences in place in the Nova Scotia Offshore area was presented. Their total work bid was just over $188 million. In 1998, the Board's exploration activity included the review and approval for nine seismic programs. The Board also continues to monitor the extended Cohasset Benefits Plan to cover the scope of PanCanadian's Exploratory Drilling Program. This report included statements of financial position, revenue and expenditure, changes in financial position, and notes to the financial statements including accounting policies, accounts receivable, deferred revenue and commitments. The report also admitted uncertainty due to the year 2000 issue. It stated that it is not possible to be certain that all aspects of the year 2000 issue affecting the Board will be fully resolved. tabs., figs

Seize the data (Carpe data) : wave of computerized data capture technology sweeps drilling industry

Energy Technology Data Exchange (ETDEWEB)

Mahoney, J.

1999-02-01

The computerization of all aspects of the monitoring and collection of well drilling information is discussed. Global Link International Inc. of Calgary, has developed a computerized system for tracking and recording drilling data. This operations recording database is named the Electronic Tour Book (ETB). It is similar to the Electronic Tour Sheet (ETS) developed by Chimo Equipment Ltd. of Alberta. Both Windows-based systems represent computerized reporting mechanisms for operators, producers, loggers and rig-managers. Another Alberta company, Ryan Energy Technologies Inc., has begun marketing the Tru Vu Fusion system of hardware and software, yet another system for gathering and recording drilling data. Tru Vu Fusion can capture data and display it in a format that everybody at the wellsite can use for decision making. Another drilling data management system, entitled INSITE (for Integrated System for Information Technology and Engineering) is marketed by Sperry-Sun Drilling Services. While INSITE is intended primarily for offshore drilling applications, it can be used onshore with equal success. 4 figs.

Visual effects of test drilling for natural gas in the Waddenzee and the North Sea coastal area

International Nuclear Information System (INIS)

Dijkstra, H.

1996-01-01

The potential hindrance of the view, caused by offshore platforms, has been investigated as part of the environmental impact reports for test drilling for natural gas in the North Sea area, on the island Ameland and in the Wadden Sea. The hindrance is determined by calculating the weighed numbers of inhabitants and vacationers within 10 km of 26 drilling sites, divided over 12 drilling areas. For each drilling area the preferred location was determined. The hindrance of the view is the lowest when drilling tests are carried out in the winter. Also digital photo paste-ups were made by which it can be shown how drilling installations look like in a landscape. Finally, measures are given by which the visual effects of drilling installations and burn off can be reduced. 34 figs., 33 tabs., 2 appendices, 35 refs

Combatting operational pollution from offshore petroleum activities: international legal regime

International Nuclear Information System (INIS)

Vinogradov, S.V.; Wagner, J.P.

1997-01-01

Existing global and regional rules and regulations, and regulatory trends, aimed at curbing pollution associated with the normal operation of offshore oil and gas installations are assessed. The designation 'operational pollution' is used to cover a variety of discharges including: oil produced in water; contaminated drill cuttings and muds; sewage; garbage; deck drainage; naturally occurring materials such as radionuclides, heavy metals and aromatics; atmospheric emissions, principally CO 2 , SO x , NO x , CH 4 and volatile organic compounds. The main focus of regulatory attention at present is platform drainage, offshore processing drainage, production water discharge, and displacement discharge. The legal framework considered extends to the appropriate global and regional treaties, ''soft law'' instruments and recommendations. (UK)

) A Feasibility Study for High Resolution 3D Seismic In The Deep Offshore Nigeria

International Nuclear Information System (INIS)

Enuma, C.; Hope, R.; Mila, F.; Maurel, L.

2003-01-01

The conventional Exploration 3D seismic in the Deep Offshore Nigeria is typically acquired with 4000m-6000m cable length at 6-8 depth and with flip-flop shooting, providing a shot point interval of 50m. the average resulting frequency content is typically between 10-60hz which is adequate for exploration interpretation. It has become common in the last few years. E.g. in Angola and the Gulf of Mexico, to re-acquire High Resolution 3D seismic, after a discovery, to improve definition of turbidite systems and accuracy of reservoir geometry for optimized delineation drilling. This feasibility study which was carried out in three different steps was due to the question on whether HR-Seismic should be acquired over TotalFinaElf AKPO discovery for optimized delineation drilling

46 CFR 109.203 - Sanitation.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Sanitation. 109.203 Section 109.203 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Tests, Drills, and Inspections § 109.203 Sanitation. (a) The master or person in charge shall insure that the accommodation...

Development of a Math Input Interface with Flick Operation for Mobile Devices

Science.gov (United States)

Nakamura, Yasuyuki; Nakahara, Takahiro

2016-01-01

Developing online test environments for e-learning for mobile devices will be useful to increase drill practice opportunities. In order to provide a drill practice environment for calculus using an online math test system, such as STACK, we develop a flickable math input interface that can be easily used on mobile devices. The number of taps…

Multi-scale Onland-Offshore Investigations of the New Caledonia Ophiolite, SW Pacific

Science.gov (United States)

Clerc, C. N.; Collot, J.; Sevin, B.; Patriat, M.; Etienne, S.; Iseppi, M.; Lesimple, S.; Jeanpert, J.; Mortimer, N. N.; Poli, S.; Pattier, F.; Juan, C.; Robineau, B.; Godard, M.; Cluzel, D.

2017-12-01

The Peridotite Nappe of New Caledonia is one of the largest ultramafic ophiolite in the World: it represents about one quarter of the 500 x 80 km island of Grande Terre. This extensive upper mantle unit was tectonically emplaced during the Eocene onto the northeastern edge of Zealandia continent. It is weakly deformed because it was not involved in a collision belt after obduction. A dome-shaped Eocene HP/LT metamorphic complex was exhumed across the fore-arc mantle lithosphere in the northern tip of the island. Post-obduction Miocene to Present coral reefs developed in shallow waters around Grande Terre and surrounding islands. In the perspective of a possible onshore/offshore drilling project (IODP/ICDP), we present recent advances in our understanding of offshore extensions of this ophiolite. To the south of New Caledonia, the offshore continuation of the ultramafic allochthon has been identified by dredges and by its geophysical signature as a continuous linear body that extends over a distance of more than 400 km at about 2000m bsl. Such water depths allow an unprecedented seismic reflection imaging of a drowned and well-preserved ophiolite. Seismic profiles show that the nappe has a flat-top, and is capped by carbonate reefs and dissected by several major normal faults. To the east of this presumed ultramafic body, Felicité Ridge is a 30 km wide, 350 km long, dome-shaped ridge, which may be interpreted as the possible southern extension of the HP/LT metamorphic complex observed onshore. Onshore, several 150 to 200 m long cores were drilled in the ophiolite and airborne electromagnetic allowed high-resolution imaging down to 400 m depth. These recent results allow identification of internal thrusts within the peridotite body and more superficial landslides. The analysis of polyphase fracturation and associated serpentinization brings new constraints on the tectonic evolution of the ophiolite and its subsequent weathering pattern. We integrate these data and

Canada-Newfoundland Offshore Petroleum Board : annual report 1998/1999

International Nuclear Information System (INIS)

1999-01-01

Financial information from the Canada-Newfoundland Offshore Petroleum Board and a review of their operations was presented. The Board manages the petroleum resources in the Newfoundland Offshore area on behalf of the Canadian Government and the Newfoundland and Labrador Government. The Board ensures that resource development is conducted in accordance with good oilfield practice to optimize recovery and avoid waste. Energy resource activities were summarized. A total of nine offshore seismic surveys were completed during the summer of 1998, the largest acquisition of seismic data in any one year. The surveys recorded 76,000 km of 2-D and 3-D seismic data. The drilling and production activities of the Hibernia field were also reviewed. 24 million bbls of oil were produced from the platform during the 1998 calendar year. The Terra Nova project continues to progress for a first oil target date of late 2000. This report presented an operations review, exploration activity, and consolidated financial statements. Revenue and expenditure statements were summarized by source. tabs., figs

Artificial intelligence applications in offshore oil and gas production

International Nuclear Information System (INIS)

Attia, F.G.

1994-01-01

The field of Artificial Intelligence (AI) has gained considerable acceptance in virtually all fields, of engineering applications. Artificial intelligence is now being applied in several areas of offshore oil and gas operations, such as drilling, well testing, well logging and interpretation, reservoir engineering, planning and economic evaluation, process control, and risk analysis. Current AI techniques offer a new and exciting technology for solving problems in the oil and gas industry. Expert systems, fuzzy logic systems, neural networks and genetic algorithms are major AI technologies which have made an impact on the petroleum industry. Presently, these technologies are at different stages of maturity with expert systems being the most mature and genetic algorithms the least. However, all four technologies have evolved such that practical applications were produced. This paper describes the four major Al techniques and their many applications in offshore oil and gas production operations. A summary description of future developments in Al technology that will affect the execution and productivity of offshore operations will be also provided

Coral ages and island subsidence, Hilo drill hole

Science.gov (United States)

Moore, J.G.; Ingram, B.L.; Ludwig, K. R.; Clague, D.A.

1996-01-01

A 25.8-m-thick sedimentary section containing coral fragments occurs directly below a surface lava flow (the ???1340 year old Panaewa lava flow) at the Hilo drill hole. Ten coral samples from this section dated by accelerator mass spectrometry (AMS) radiocarbon and five by thermal infrared multispectral scanner (TIMS) 230Th/U methods show good agreement. The calcareous unit is 9790 years old at the bottom and 1690 years old at the top and was deposited in a shallow lagoon behind an actively growing reef. This sedimentary unit is underlain by a 34-m-thick lava flow which in turn overlies a thin volcaniclastic silt with coral fragments that yield a single 14C date of 10,340 years. The age-depth relations of the dated samples can be compared with proposed eustatic sea level curves after allowance for island subsidence is taken. Island subsidence averages 2.2 mm/yr for the last 47 years based on measurements from a tide gage near the drill hole or 2.5-2.6 mm/yr for the last 500,000 years based on the ages and depths of a series of drowned coral reefs offshore from west Hawaii. The age-depth measurements of coral fragments are more consistent with eustatic sea levels as determined by coral dating at Barbados and Albrolhos Islands than those based on oxygen isotopic data from deep sea cores. The Panaewa lava flow entered a lagoon underlain by coral debris and covered the drill site with 30.9 m of lava of which 11 m was above sea level. This surface has now subsided to 4.2 m above sea level, but it demonstrates how a modern lava flow entering Hilo Bay would not only change the coastline but could extensively modify the offshore shelf.

The Performance of Corporate Alliances: Evidence from Oil and Gas Drilling in the Gulf of Mexico

OpenAIRE

Beshears, John Leonard

2013-01-01

I use data on oil and gas drilling in the Gulf of Mexico to measure how a corporate alliance—a group of firms that jointly develops an offshore tract—performs relative to a solo firm. I employ a regression discontinuity strategy based on bids in first-price sealed-bid auctions for the rights to develop leases. By focusing on leases where one organizational form narrowly outbids the other, I measure drilling outcomes while controlling for the endogenous matching of projects and organizational ...

Dual gradient drilling: barite separation from the mud using hydrocyclones; Perfuracao com duplo gradiente: a separacao da barita do fluido de perfuracao utilizando hidrociclones

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Aline T.; Medronho, Ricardo A. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Escola de Quimica

2004-07-01

The proximity of the pores pressure and fracture pressure curves in deep water drilling makes it an expensive and complicated operation. It is possible to minimize this problem by reducing the pressure inside the riser at the sea floor level. Injecting low density drilling mud at that point is an alternative, producing a condition called as dual gradient drilling. Hydrocyclones are simple apparatuses and their high capacity and efficiency make them appropriate for operations were the occupied floor space plays an important hole, as in offshore drilling. The idea behind this work is to divide the drilling mud in two streams, one more concentrated in barite for re-injection into the drilling column, and other more diluted for injecting into the riser at the sea floor. In this work, CFD - computational fluid dynamics - was used to investigate barite separation from drilling mud using hydrocyclones. The results indicate that the injection of a lower density mud, less concentrate in barite, in the riser at sea floor level may be a possible and less complicated alternative for dual gradient drilling. (author)

U.S. drilling: Solid reasons for optimism

International Nuclear Information System (INIS)

Anon.

1997-01-01

One year ago, it was apparent that 1996 would be a better year for drilling in the US, primarily because 1995 performance was lower than expected due to low oil and natural gas prices in mid-year during the peak drilling season. Improving energy prices last year did spur more drilling, and a 2.9% increase to a total 23,560 wells is estimated for 1996. This year should show an even stronger increase, as the US gas market remains attractive and industry's perception is that crude prices are stabilizing at higher levels, i.e., $20--25, instead of $15--20. The US rotary rig count followed the price up, from a low near 700 in January/February to slightly over 850 in December. To drill the expected wells this year will require an average number at the 850 level. Operators are investing more in their established oil producing areas to take advantage of improved cast flows. This will generate higher activity nearly everywhere. Gas drilling activity will be more geographical, depending on transport availability to surging winter markets and Canadian competition. The US, and world, hot spot is the Gulf of Mexico led by renewed activity on the shelf and an exciting new deepwater play. The expected activity surge has already taxed a service industry that has not yet upgraded its capacity from the long downturn. And spot shortages will temper the activity rise, particularly offshore. The following discussion and six statistical presentations detail these basic concepts and other key factors

Life extension of semi-submersible drilling unit

Energy Technology Data Exchange (ETDEWEB)

Hadley, I.; Sinclair, C.I.K. [TWI, Cambridge (United Kingdom). Structural Integrity Dept.; Magne, E. [Schlumberger Sedco Forex, Montrouge (France)

1995-12-31

This paper describes the life extension of a semi-submersible drilling rig built in the early 1970`s. A nominal design life of 20 years was estimated at the time of building; however, in the interim period, numerous improvements have been made in fatigue life estimation ad life improvement techniques, raising the possibility that a further 20 years of operation could be considered. The life extension strategy made use of a number of aspects of offshore technology which were not available at the time of construction of the rig. Finite element studies and results from offshore research programs were used to gauge the effect of fatigue life improvement techniques. The program demonstrated the feasibility of extending the operation of the rig for a further 20 years, with the interval between in-service inspection increased to every five years. It also provided a valuable database of fracture toughness data for the rig materials, which may be used in future work to address reliability issues.

Water base drilling fluids for high-angle wells; Fluidos a base de agua para perfuracao de pocos com elevada inclinacao

Energy Technology Data Exchange (ETDEWEB)

Passarelli, Rui [PETROBRAS, Rio de Janeiro (Brazil). Dept. de Perfuracao. Div. de Fluidos de Perfuracao; Lomba, Rosana Fatima T [PETROBRAS, Rio de Janeiro (Brazil). Centro de Pesquisas. Div. de Explotacao

1990-12-31

Horizontal drilling has experimented a large increase in last years. In Brazil, two horizontal wells were drilled in Fazenda Belem and Carmopolis Fields. The first one reached a final measured depth of 1128 m and the horizontal length was 533 m. The drilling fluid program was elaborated after a large number of laboratory tests, in order to get a composition that best fitted the drilling requirements, mainly the desirable lubricity. The idea of using a water-base fluid instead of an oil-based, known as more suitable in this case, arose because the Company is interested in drilling this kind of well offshore, in deep water, where the use of oil-base muds is forbidden. Different compositions of water base muds were developed and tested in laboratory and the results led to low-solids salt fluids having a lubricant in its composition. The lubricity coefficients of these fluids are similar to those obtained with oil-base muds. 9-FZB-446D-CE well was drilled with the chosen fluid and high values of torque and drag were not registered, being the operation a total success. (author) 10 tabs.

Water base drilling fluids for high-angle wells; Fluidos a base de agua para perfuracao de pocos com elevada inclinacao

Energy Technology Data Exchange (ETDEWEB)

Passarelli, Rui [PETROBRAS, Rio de Janeiro (Brazil). Dept. de Perfuracao. Div. de Fluidos de Perfuracao; Lomba, Rosana Fatima T. [PETROBRAS, Rio de Janeiro (Brazil). Centro de Pesquisas. Div. de Explotacao

1989-12-31

Horizontal drilling has experimented a large increase in last years. In Brazil, two horizontal wells were drilled in Fazenda Belem and Carmopolis Fields. The first one reached a final measured depth of 1128 m and the horizontal length was 533 m. The drilling fluid program was elaborated after a large number of laboratory tests, in order to get a composition that best fitted the drilling requirements, mainly the desirable lubricity. The idea of using a water-base fluid instead of an oil-based, known as more suitable in this case, arose because the Company is interested in drilling this kind of well offshore, in deep water, where the use of oil-base muds is forbidden. Different compositions of water base muds were developed and tested in laboratory and the results led to low-solids salt fluids having a lubricant in its composition. The lubricity coefficients of these fluids are similar to those obtained with oil-base muds. 9-FZB-446D-CE well was drilled with the chosen fluid and high values of torque and drag were not registered, being the operation a total success. (author) 10 tabs.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

Energy Technology Data Exchange (ETDEWEB)

Alan Black; Arnis Judzis

2003-01-01

Progress during current reporting year 2002 by quarter--Progress during Q1 2002: (1) In accordance to Task 7.0 (D. No.2 Technical Publications) TerraTek, NETL, and the Industry Contributors successfully presented a paper detailing Phase 1 testing results at the February 2002 IADC/SPE Drilling Conference, a prestigious venue for presenting DOE and private sector drilling technology advances. The full reference is as follows: IADC/SPE 74540 ''World's First Benchmarking of Drilling Mud Hammer Performance at Depth Conditions'' authored by Gordon A. Tibbitts, TerraTek; Roy C. Long, US Department of Energy, Brian E. Miller, BP America, Inc.; Arnis Judzis, TerraTek; and Alan D. Black, TerraTek. Gordon Tibbitts, TerraTek, will presented the well-attended paper in February of 2002. The full text of the Mud Hammer paper was included in the last quarterly report. (2) The Phase 2 project planning meeting (Task 6) was held at ExxonMobil's Houston Greenspoint offices on February 22, 2002. In attendance were representatives from TerraTek, DOE, BP, ExxonMobil, PDVSA, Novatek, and SDS Digger Tools. (3) PDVSA has joined the advisory board to this DOE mud hammer project. PDVSA's commitment of cash and in-kind contributions were reported during the last quarter. (4) Strong Industry support remains for the DOE project. Both Andergauge and Smith Tools have expressed an interest in participating in the ''optimization'' phase of the program. The potential for increased testing with additional Industry cash support was discussed at the planning meeting in February 2002. Progress during Q2 2002: (1) Presentation material was provided to the DOE/NETL project manager (Dr. John Rogers) for the DOE exhibit at the 2002 Offshore Technology Conference. (2) Two meeting at Smith International and one at Andergauge in Houston were held to investigate their interest in joining the Mud Hammer Performance study. (3) SDS Digger Tools (Task 3

Integration of Wave and Offshore Wind Energy in a European Offshore Grid

DEFF Research Database (Denmark)

Chozas, Julia Fernandez; Sørensen, H. C.; Korpås, M.

2010-01-01

of offshore renewable energy sources. According to this, the paper covers i) public and private initiatives for offshore transmission networks, ii) the synergies between the wave and the offshore wind energy sector within an offshore grid, iii) power transmission options for offshore generation and iv...

Damage to offshore infrastructure in the Gulf of Mexico by hurricanes Katrina and Rita

Science.gov (United States)

Cruz, A. M.; Krausmann, E.

2009-04-01

The damage inflicted by hurricanes Katrina and Rita to the Gulf-of-Mexico's (GoM) oil and gas production, both onshore and offshore, has shown the proneness of industry to Natech accidents (natural hazard-triggered hazardous-materials releases). In order to contribute towards a better understanding of Natech events, we assessed the damage to and hazardous-materials releases from offshore oil and natural-gas platforms and pipelines induced by hurricanes Katrina and Rita. Data was obtained through a review of published literature and interviews with government officials and industry representatives from the affected region. We also reviewed over 60,000 records of reported hazardous-materials releases from the National Response Center's (NRC) database to identify and analyze the hazardous-materials releases directly attributed to offshore oil and gas platforms and pipelines affected by the two hurricanes. Our results show that hurricanes Katrina and Rita destroyed at least 113 platforms, and severely damaged at least 53 others. Sixty percent of the facilities destroyed were built 30 years ago or more prior to the adoption of the more stringent design standards that went into effect after 1977. The storms also destroyed 5 drilling rigs and severely damaged 19 mobile offshore drilling units (MODUs). Some 19 MODUs lost their moorings and became adrift during the storms which not only posed a danger to existing facilities but the dragging anchors also damaged pipelines and other infrastructure. Structural damage to platforms included toppling of sections, and tilting or leaning of platforms. Possible causes for failure of structural and non-structural components of platforms included loading caused by wave inundation of the deck. Failure of rigs attached to platforms was also observed resulting in significant damage to the platform or adjacent infrastructure, as well as damage to equipment, living quarters and helipads. The failures are attributable to tie-down components

Islands of steel rise over North Sea gas. Pt. 1

Energy Technology Data Exchange (ETDEWEB)

Hind, J A

1965-10-27

Nowhere is the offshore oil and gas prospecting boom more enthusiastic, urgent, and crowded than in the North Sea. The type of rig required for this type of offshore drilling mainly depends upon how far offshore drilling is to take place. The fixed jack-up type is most suitable where depth of water is not excessive and for actual drilling operations were the drill is most easily held steady over the hole. This type of rig presents a stability problem under tow from location to location with a shallow depth of hull. Depth of water limits the operational mobility of the submerged-type rig and it is the most prone to scouring effects. Fully floating and ship-mounted rigs solve the depth of water problem and many others associated with ocean transportation. However, this is at the expense of more difficult drilling operations and complexity of equipment. Semi-submersibles are a popular compromise between fixed sit-on-bottom rigs and fully floating types. From a naval architectural point of view they have much to recommend them as all- round units. Typical North Sea drill rigs are described and a table is given for complete details.

Implications of the Netherlands' environmental policy for offshore mining

International Nuclear Information System (INIS)

Meijer, K.; Krijt, K.

1991-01-01

The environmental policy in the Netherlands, as outlined in the National Environmental Policy Plan, aims for a sustainable development. In principle a two track approach is adhered to: source oriented as well as effects oriented. Effects oriented policy includes the setting of environmental quality objectives and is used to establish the final goals for the source-oriented measures. The policy aims at integrated life-cycle management; in the final target situation all waste is used again as raw material and remaining emissions to the environment should comply with the environmental objectives. In this paper the implications of this policy for the offshore mining industry are elaborated, both for drilling operations and for the production of oil, gas and condensate. The results of the recently concluded Environmental Impact Assessment for the offshore mining industry as a whole are also elaborated

SEASAT demonstration experiments with the offshore oil, gas and mining industries

Science.gov (United States)

Mourad, A. G.; Robinson, A. C.; Balon, J. E.

1979-01-01

Despite its failure, SEASAT-1 acquired a reasonable volume of data that can be used by industrial participants on a non-real-time basis to prove the concept of microwave sensing of the world's oceans from a satellite platform. The amended version of 8 experimental plans are presented, along with a description of the satellite, its instruments, and the data available. Case studies are summarized for the following experiments: (1) Beaufort Sea oil, gas, and Arctic operations; (2) Labrador Sea oil, gas, and sea ice; (3) Gulf of Mexico pipelines; (4) U.S. East Coast offshore oil and gas; (5) worldwide offshore drilling and production operations; (6) Equatorial East Pacific Ocean mining; (7) Bering Sea ice project; and (8) North Sea oil and gas.

Wind of opportunity

International Nuclear Information System (INIS)

Jamieson, Peter

1999-01-01

This article traces the move towards the offshore exploitation of wind energy in Europe, and presents information on existing offshore wind energy projects and proposed wind turbine prototypes for offshore operation. The building of the first major offshore wind project at Vindeby, the use of rock socketed monopile foundations for pile drilling and erection of the wind turbines from a mobile jack-up barge, the costs of wind turbines, the fatigue loads on the support structures due to the wind loading, and the offshore wind market in the UK and Europe are discussed. (UK)

Environmental effects monitoring for exploration drilling

International Nuclear Information System (INIS)

Buchanan, R.A.; Cook, J.A.; Mathieu, A.

2003-01-01

Strategies for monitoring the environmental effects of single exploratory offshore wells on the east coast of Canada were evaluated. The report was compiled from consultations with scientists, regulators and stakeholders as well as a review of regulatory regimes and toxicity results. The aim of the report was to develop a decision tree for determining when to conduct environmental effects monitoring (EEM). Respondents evinced lower levels of concern for single exploratory wells than for production developments. A number of scientists argued for full statistical treatment of all data, and many people argued that more assurance was needed that the marine environment was not being unduly harmed. Respondents also considered that biological effects should be a primary focus, rather than the occurrence of trace chemical signals, and that seabirds and mammals should be monitored. Concern was expressed over the value of data collected from monitoring the effects of exploratory drilling activities. It was suggested that local and site-specific issues should be considered in the design of EEM programs. Respondents expressed strong concern about potential cumulative effects with other industrial activities, and suggested that test cases should be established and monitored to develop a scientific rationale for the inclusion or exclusion of specific variables in future EEM programs. A decision tree was developed based on 3 scenarios: (1) compliance monitoring only in well known areas with no sensitive issues; opportunistic EEM surveys of sediments, benthos, seabirds and marine mammals in shallow or deep areas with no known sensitive issues; and (3) custom EEM surveys for sensitive areas. Currently, there are EEM requirements for drilling exploratory wells offshore Canada's east coast. 58 refs., 2 tabs., 7 figs

Offshore concrete structures; Estructuras Offshore (mar adentro) de Hormigon

Energy Technology Data Exchange (ETDEWEB)

Lamas Pardo, M.; Carral Couce, L. M.

2011-07-01

In the offshore industry there are two possible materials for the construction of the hull of a structure; the steel and concrete, with the first one widely used until now, as in the rest of the shipbuilding industry of merchant ships, warships, etc. Materials such as aluminum, GRP or timber areused in small units with lengths lower than 100 m, and in less adverse conditions than in the offshore industry. Nevertheless, some ships/barges have been built of concrete in the past, but have been rather isolated cases which have not changed the practice in the industry. In the First and Second World War were built by the scarcity of materials, while the series of barges by Alfred A. Yee was a rare exception. Other units were also made in concrete, but almost anecdotal. Still, the behaviour of these concrete structures, especially in terms of maintenance, has been excellent. Therefore, the fact that the concrete has not had an adequate reception so far in shipbuilding, does not mean that in will not be the material best suited for the offshore industry in the future. The extra displacement and associated fuel costs in concrete ships have been found prohibitive in the past. But the loss of mobility of a concrete hull in relation to a steel hull can be perfectly offset by the advantages offered by the concrete, as the shipping and offshore industry have very different priorities. One of the main differences in these priorities is in terms of maintenance and resistance to fatigue, precisely where the concrete performs better. ships can easily be dry docked for maintenance and repair, while in the offshore platforms these works have to be done in situ so maintenance and fatigue are crucial to them. Besides these, the concrete has other advantages according to findings of several studies. And although they are interested in the conclusions that the makes as they came from people in the concrete industry, the fact that in recent years concrete offshore unit shave been built

A new drilling method-Earthworm-like vibration drilling.

Science.gov (United States)

Wang, Peng; Ni, Hongjian; Wang, Ruihe

2018-01-01

The load transfer difficulty caused by borehole wall friction severely limits the penetration rate and extended-reach limit of complex structural wells. A new friction reduction technology termed "earthworm-like drilling" is proposed in this paper to improve the load transfer of complex structural wells. A mathematical model based on a "soft-string" model is developed and solved. The results show that earthworm-like drilling is more effective than single-point vibration drilling. The amplitude and frequency of the pulse pressure and the installation position of the shakers have a substantial impact on friction reduction and load transfer. An optimization model based on the projection gradient method is developed and used to optimize the position of three shakers in a horizontal well. The results verify the feasibility and advantages of earthworm-like drilling, and establish a solid theoretical foundation for its application in oil field drilling.

Experimental study on moonpool resonance of offshore floating structure

Directory of Open Access Journals (Sweden)

Seung-Ho Yang

2013-06-01

Full Text Available Offshore floating structures have so-called moonpool in the centre area for the purpose of drilling, installation of subsea structures, recovery of Remotely-Operated Vehicle (ROV and divers. However, this vertical opening has an effect on the operating performance of floating offshore structure in the vicinity of moonpool resonance frequency; piston mode and sloshing mode. Experimental study based on model test was carried out. Moonpool resonance of floating offshore structure on fixed condition and motion free condition were investigated. And, the effect of cofferdam which is representative inner structure inside moonpool was examined. Model test results showed that Molin's theoretical formula can predict moonpool resonance on fixed condition quite accurately. However, motion free condition has higher resonance frequency when it is compared with that of motion fixed. The installation of cofferdam moves resonance frequency to higher region and also generates secondary resonance at lower frequency. Furthermore, it was found that cofferdam was the cause of generating waves in the longitudinal direction when the vessel was in beam sea.

Review of BEPCo's exploration drilling environmental assessment update

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This report was presented in response to a request from the Canada-Nova Scotia Offshore Petroleum Board for advice on the accuracy of an update to an environmental assessment report related to BEPCo's proposed exploratory drilling project offshore of Nova Scotia, which had received approval in June 2005 but was then delayed. BEPCo was seeking approval to proceed with the same project from 2009 to 2015, although the proposed project lease area was half the size of the original proposal. Advice was sought with respect to potential drilling and seismic impacts to the marine environment, any new information since 2005 regarding marine benthic habitat, non-commercial fish species, marine animals, or spawning areas of critical habitat in the area, and whether DFO Science was planning to undertake research in the area during the period in question. Summaries were presented for the new environmental impact information and the new ecosystem information, including updated species at risk information. BEPCo's updated environmental assessment did not include all of the newly available information. Although it was not clear that is new information would change the conclusions of the initial environmental assessment, it would be useful in designing and implementing an Environmental Effects Monitoring program. 21 refs.

Gravity-Independent Mobility and Drilling on Natural Rock using Microspines

Science.gov (United States)

Parness, Aaron; Frost, Matthew; Thatte, Nitish; King, Jonathan P.

2012-01-01

To grip rocks on the surfaces of asteroids and comets, and to grip the cliff faces and lava tubes of Mars, a 250 mm diameter omni-directional anchor is presented that utilizes a hierarchical array of claws with suspension flexures, called microspines, to create fast, strong attachment. Prototypes have been demonstrated on vesicular basalt and a'a lava rock supporting forces in all directions away from the rock. Each anchor can support >160 N tangent, >150 N at 45?, and >180 N normal to the surface of the rock. A two-actuator selectively- compliant ankle interfaces these anchors to the Lemur IIB robot for climbing trials. A rotary percussive drill was also integrated into the anchor, demonstrating self-contained rock coring regardless of gravitational orientation. As a harder- than-zero-g proof of concept, 20mm diameter boreholes were drilled 83 mm deep in vesicular basalt samples, retaining a 12 mm diameter rock core in 3-6 pieces while in an inverted configuration, literally drilling into the ceiling.

Reforming Brazil's offshore oil and gas safety regulatory framework: Lessons from Norway, the United Kingdom and the United States

International Nuclear Information System (INIS)

Mendes, Pietro A.S.; Hall, Jeremy; Matos, Stelvia; Silvestre, Bruno

2014-01-01

We propose reforming the Brazilian regulatory safety framework (BRSF) for offshore oil and gas production and drilling operations. Brazil has emerged as a leading offshore producer with extensive proven reserves yet to be exploited. However, the BRSF has not been updated since 2007, and there are now major concerns about the industry's safety, particularly after the BP Deepwater Horizon accident, along with the technical challenges due to extreme conditions under which Brazil's resources are located. Drawing on experiences from three leading offshore oil and gas producers (Norway, the UK, and the US), we recommend the adoption of three best practices: the UK's ‘safety case’ approach (where operators are expected to provide convincing and valid arguments that a system is sufficiently safe for a given application in a specific environment), Norway's ‘barrier management’ (evidence that there are at least two tested and independent barriers to avoid accidents) and greater investment in safety research and development, as suggested by the US's National Commission on the BP Deepwater Horizon Oil Spill and Offshore Drilling. We discuss implications for policy reform and how best practices can be applied within the Brazilian context. - Highlights: • Description of the Brazilian regulatory safety framework (BRSF). • Comparison between BRSF and regulatory frameworks of leading offshore oil and gas jurisdictions (Norway, UK and US). • Recommendations for BRSF to include the safety case, barrier management and increased investment in safety technology

Technical and economic evaluation of selected compact drill rigs for drilling 10,000 foot geothermal production wells

Energy Technology Data Exchange (ETDEWEB)

Huttrer, G.W. [Geothermal Management Company, Inc., Frisco, CO (United States)

1997-11-01

This report summarizes the investigation and evaluation of several {open_quotes}compact{close_quotes} drill rigs which could be used for drilling geothermal production wells. Use of these smaller rigs would save money by reducing mobilization costs, fuel consumption, crew sizes, and environmental impact. Advantages and disadvantages of currently-manufactured rigs are identified, and desirable characteristics for the {open_quotes}ideal{close_quotes} compact rig are defined. The report includes a detailed cost estimate of a specific rig, and an evaluation of the cost/benefit ratio of using this rig. Industry contacts for further information are given.

A feasibility study of the offshore disposal of radioactive waste by drilled emplacement

International Nuclear Information System (INIS)

1984-01-01

This report describes the third phase of a study of the feasibility of disposal and isolation of high level radioactive waste in holes drilled deep into the sediments of the ocean. In this phase, work has concentrated on establishing the logistics of disposing of up to 400 cubic metres of vitrified waste per year, and on the capital and running costs of doing so. The report concludes that the disposal of waste in the form produced by the AVM process is operationally feasible, and that disposal in this way will add approximately 0.2% to the cost of generation of the energy contributing to the waste. (author)

Running casing on conventional wells with Casing Drilling {sup TM} technology

Energy Technology Data Exchange (ETDEWEB)

Warren, T.M.; Schneider, W.P.; Johns, R.P.; Zipse, K.D. [Tesco Corp., Calgary, AB (Canada)

2004-07-01

Casing Drilling{sup TM} is a newly developed and efficient well construction method that combines drilling and casing running processes into a single operation. This radical change to the entire well casing running process eliminates standard components and processes that are inefficient and hazardous. The commercialization of this new technology has resulted in the development of custom equipment and procedures designed to efficiently handle casings on a drilling rig, including conventionally drilled wells. The technology offers safer casing running operations and makes it possible to ream casing to the bottom. In addition, less people are needed to operate the portable Casing Drive System (CDS). One of the primary components of the system is the top drive which provides the power for rotation and torque. The CDS supports full axial and torsional load for running the casing. The well can be circulated while running the casing. The casing can be washed and reamed to the bottom whenever a tight hole is encountered. Thirty one operators have successfully used the CDS on more than 150 onshore and offshore wells in 7 countries. 13 refs., 2 tabs., 12 figs.

46 CFR 108.419 - Fire main capacity.

Science.gov (United States)

2010-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Fire Extinguishing Systems Fire Main System § 108.419 Fire main capacity. The diameter of the fire... pumps operating simultaneously. ...

46 CFR 112.05-5 - Emergency power source.

Science.gov (United States)

2010-10-01

...; tankships; barges with sleeping accommodations for more than 6 persons; mobile offshore drilling units; and... fans, CO2 bottles, space heaters, and internal communication devices, such as sound powered phones. (e...

Offshore oil and gas activities in the PERD program

Energy Technology Data Exchange (ETDEWEB)

Billette, N. [Natural Resources Canada, Ottawa, ON (Canada). Office of Energy Research and Development

2001-07-01

Natural Resources Canada manages the Program of Energy Research and Development (PERD), which covers all but a few of non-nuclear energy areas. The aim of the Program is to focus on research and technology developments that support a dynamic and diversified energy supply, while encouraging industries to consume the energy efficiently. Twelve federal departments and agencies are stakeholders in energy research and development and the 57 million dollar annual budget is allocated amongst the stakeholders according to the priorities established. Each year, one-quarter of the program is evaluated externally and potential reallocation examined, a recent initiative implemented as part of a results-based management (RBM) system. Five federal departments and one agency carry out offshore research and development activities, touching the fields of basin assessment and geotechnics in the Canadian North and offshore East Coast, winds-wave-current modelling, the management of sea ice, iceberg and ice-structure interactions, ship design and navigation issues. In this last category, activities related to offshore safety, management of offshore drilling and production wastes, oil spills remediation, and assessment of cumulative effects of wastes and produced waters are included. These activities are detailed in the presentation, and the author discussed the future shifts likely to occur in PERD so that the needs of the regulatory agencies in terms of science and technology are met. There is also the aspect of the protection of the interests of the Canadian public to consider. 1 tab.

MUDMAP: Simulation model for releases from offshore platforms

International Nuclear Information System (INIS)

Anon.

1994-01-01

The present article deals with a Norwegian developed simulation model dubbed MUDMAP. MUDMAP is a numerical model that simulates releases of drill muds and cuttings, produced water and other substances from offshore platforms. The model is envisioned as an advanced tool to assist in the rapid design and placement of intakes and release pipes on platforms, as well as in evaluating potential long-term impacts in the water and on the sea floor. MUDMAP allows rapid visual/graphical analysis of potential alternative solutions under various realistic environmental conditions, and for planning and executing platform monitoring projects. 4 figs

Environmental implications of offshore oil and gas development in Australia. The finding of an independent scientific review

International Nuclear Information System (INIS)

Swan, J.M.; Neff, J.M.; Young, P.C.

1994-01-01

It is widely recognised that uncontrolled discharge of petroleum products or other materials from offshore oil and gas exploration and production wells, and from associated industrial operations including treatment and service facilities that are required to be on or near the coast, can have direct and sometimes deleterious impacts on the marine environment. In mid-1992, the Australian Petroleum Exploration Association (APEA) commissioned five scientific reviews to examine the environmental implications of offshore petroleum developments in Australia. The reviews, carried out by an Independent Scientific Review Committee on behalf of the Australian Petroleum Exploration Association (APEA) and the Energy Research and Development Corporation (ERDC) deal with: (1) the preliminary geophysical exploration of the sea bed and underlying strata using seismic surveys, and especially the effects of bursts of underwater sound energy on biological communities; (2) the drilling of offshore wells, especially the disposal of drilling fluids and drill cuttings; (3) the production of oil and gas from proven wells, especially the disposal of large quantities of produced formation water (fossil water); (4) the construction and operation of coastal support facilities and associated activities which might have consequences for marine habitats; (5) oil spills associated with any of the above operations and especially the likely short- and long-term effects of an accidental oil spill on marine biota and on the aesthetic and commercial values of an impacted coastline. Comments on the findings are preceded by a brief summary of background information, relevant technologies and the main implications for the marine environment. Some suggestions are provided for possible future research, monitoring and environmental management. refs., figs., tabs

The joint industry development of a recommended practice for the site specific assessment of mobile jackup units

International Nuclear Information System (INIS)

Jones, D.E.; Bennett, W.T.; Hoyle, M.J.R.

1993-01-01

The mobile self-elevating (drilling) unit, or jack-up, has been central to the exploration and development of offshore oil and gas reserves. In recent years there has been an increased desire to benefit from the potential economics of using these units in longer term production roles either in association with a fixed platform or as a stand-alone facility. However, until recently there had been no concerted effort to develop a consistent and commonly accepted standard for general industry use in site specific assessment of jack-ups. This paper describes the background and work carried out to develop such a standard. The project is nearing completion and has resulted in the publication of a Guideline document. A Recommended Practice and associated Commentary are (at the time of writing) in the final stage of drafting for release to the project sponsors for trial and comment prior to issuing the first Edition early in 1994

Offshore concrete structures

International Nuclear Information System (INIS)

Lamas Pardo, M.; Carral Couce, L. M.

2011-01-01

In the offshore industry there are two possible materials for the construction of the hull of a structure; the steel and concrete, with the first one widely used until now, as in the rest of the shiphuidling industry of merchant ships, warships, etc. Materials such as aluminum, GRP or timber areused in small units with lengths lower than 100 m, and in less adverse conditions than in the offshore industry. Nevertheless, some ships/barges have been built of concrete in the past, but have been rather isolated cases which have not changed the practice in the industry. In the First and Second World War were built by the scarcity of materials, while the series of barges by Alfred A. Yee was a rare exception. Other units were also made in concrete, but almost anecdotal. Still, the behaviour of these concrete structures, especially in terms of maintenance, has been excellent. Therefore, the fact that the concrete has not had an adequate reception so far in shipbuilding, does not mean that in will not be the material best suited for the offshore industry in the future. The extra displacement and associated fuel costs in concrete ships have been found prohibitive in the past. But the loss of mobility of a concrete hull in relation to a steel hull can be perfectly offset by the advantages offered by the concrete, as the shipping and offshore industry have very different priorities. One of the main differences in these priorities is in terms of maintenance and resistance to fatigue, precisely where the concrete performs better. ships can easily be dry docked for maintenance and repair, while in the offshore platforms these works have to be done in situ so maintenance and fatigue are crucial to them. Besides these, the concrete has other advantages according to findings of several studies. And although they are interested in the conclusions that the makes as they came from people in the concrete industry, the fact that in recent years concrete offshore unit shave been built

Including impacts of particulate emissions on marine ecosystems in life cycle assessment: the case of offshore oil and gas production.

Science.gov (United States)

Veltman, Karin; Huijbregts, Mark A J; Rye, Henrik; Hertwich, Edgar G

2011-10-01

Life cycle assessment is increasingly used to assess the environmental performance of fossil energy systems. Two of the dominant emissions of offshore oil and gas production to the marine environment are the discharge of produced water and drilling waste. Although environmental impacts of produced water are predominantly due to chemical stressors, a major concern regarding drilling waste discharge is the potential physical impact due to particles. At present, impact indicators for particulate emissions are not yet available in life cycle assessment. Here, we develop characterization factors for 2 distinct impacts of particulate emissions: an increased turbidity zone in the water column and physical burial of benthic communities. The characterization factor for turbidity is developed analogous to characterization factors for toxic impacts, and ranges from 1.4 PAF (potentially affected fraction) · m(3) /d/kg(p) (kilogram particulate) to 7.0 x 10³ [corrected] for drilling mud particles discharged from the rig. The characterization factor for burial describes the volume of sediment that is impacted by particle deposition on the seafloor and equals 2.0 × 10(-1) PAF · m(3) /d/kg(p) for cutting particles. This characterization factor is quantified on the basis of initial deposition layer characteristics, such as height and surface area, the initial benthic response, and the recovery rate. We assessed the relevance of including particulate emissions in an impact assessment of offshore oil and gas production. Accordingly, the total impact on the water column and on the sediment was quantified based on emission data of produced water and drilling waste for all oil and gas fields on the Norwegian continental shelf in 2008. Our results show that cutting particles contribute substantially to the total impact of offshore oil and gas production on marine sediments, with a relative contribution of 55% and 31% on the regional and global scale, respectively. In contrast, the

A new drilling method—Earthworm-like vibration drilling

Science.gov (United States)

Wang, Peng; Wang, Ruihe

2018-01-01

The load transfer difficulty caused by borehole wall friction severely limits the penetration rate and extended-reach limit of complex structural wells. A new friction reduction technology termed “earthworm-like drilling” is proposed in this paper to improve the load transfer of complex structural wells. A mathematical model based on a “soft-string” model is developed and solved. The results show that earthworm-like drilling is more effective than single-point vibration drilling. The amplitude and frequency of the pulse pressure and the installation position of the shakers have a substantial impact on friction reduction and load transfer. An optimization model based on the projection gradient method is developed and used to optimize the position of three shakers in a horizontal well. The results verify the feasibility and advantages of earthworm-like drilling, and establish a solid theoretical foundation for its application in oil field drilling. PMID:29641615

Artificial islands for cluster-siting of offshore energy facilities: an assessment of the legal and regulatory framework

Energy Technology Data Exchange (ETDEWEB)

Backstrom, T.D.; Baram, M.

1976-06-01

One of the ways in which offshore coastal regions can be used in energy development is examined, namely through the construction of offshore islands for the siting of energy-related facilities. The purpose of the study is to review and assess the significant sectors of this accumulation of legal and regulatory authority, in order that those proposing and supervising such offshore development can formulate suggestions for coordination and rational allocation of responsibility. The potential demands on offshore resources are considerably greater than many would expect. In addition to offshore drilling and other mineral exploitation, there is increasing interest in safety of navigation, harvest and aquaculture of living marine resources, recreation, and preservation of uniquely valuable marine landscapes and ecosystems. Within this dynamic context, the offshore implications of the energy needs of the United States must be fully evaluated. New energy installations might be appropriately sited offshore on artificial islands. This legal and regulatory assessment contains little case law, new Congressional enactments, or proposed regulations and is, in general, a first-order analysis of the legal context for a new concept--the multiple-facility artificial island--which has not yet been tested, but which merits serious study as an alternative for uses of the offshore regions to meet energy requirements. An extensive bibliography containing 254 citations is included.

Numerical modelling for quantitative environmental risk assessment for the disposal of drill cuttings and mud

Science.gov (United States)

Wahab, Mohd Amirul Faiz Abdul; Shaufi Sokiman, Mohamad; Parsberg Jakobsen, Kim

2017-10-01

To investigate the fate of drilling waste and their impacts towards surrounding environment, numerical models were generated using an environmental software; MIKE by DHI. These numerical models were used to study the transportation of suspended drill waste plumes in the water column and its deposition on seabed in South China Sea (SCS). A random disposal site with the model area of 50 km × 25 km was selected near the Madalene Shoal in SCS and the ambient currents as well as other meteorological conditions were simulated in details at the proposed location. This paper was focusing on sensitivity study of different drill waste particle characteristics on impacts towards marine receiving environment. The drilling scenarios were obtained and adapted from the oil producer well at offshore Sabah (Case 1) and data from actual exploration drilling case at Pumbaa location (PL 469) in the Norwegian Sea (Case 2). The two cases were compared to study the effect of different drilling particle characteristics and their behavior in marine receiving environment after discharged. Using the Hydrodynamic and Sediment Transport models simulated in MIKE by DHI, the variation of currents and the behavior of the drilling waste particles can be analyzed and evaluated in terms of multiple degree zones of impacts.

Advanced Drilling through Diagnostics-White-Drilling

International Nuclear Information System (INIS)

FINGER, JOHN T.; GLOWKA, DAVID ANTHONY; LIVESAY, BILLY JOE; MANSURE, ARTHUR J.; PRAIRIE, MICHAEL R.

1999-01-01

A high-speed data link that would provide dramatically faster communication from downhole instruments to the surface and back again has the potential to revolutionize deep drilling for geothermal resources through Diagnostics-While-Drilling (DWD). Many aspects of the drilling process would significantly improve if downhole and surface data were acquired and processed in real-time at the surface, and used to guide the drilling operation. Such a closed-loop, driller-in-the-loop DWD system, would complete the loop between information and control, and greatly improve the performance of drilling systems. The main focus of this program is to demonstrate the value of real-time data for improving drilling. While high-rate transfer of down-hole data to the surface has been accomplished before, insufficient emphasis has been placed on utilization of the data to tune the drilling process to demonstrate the true merit of the concept. Consequently, there has been a lack of incentive on the part of industry to develop a simple, low-cost, effective high-speed data link. Demonstration of the benefits of DWD based on a high-speed data link will convince the drilling industry and stimulate the flow of private resources into the development of an economical high-speed data link for geothermal drilling applications. Such a downhole communication system would then make possible the development of surface data acquisition and expert systems that would greatly enhance drilling operations. Further, it would foster the development of downhole equipment that could be controlled from the surface to improve hole trajectory and drilling performance. Real-time data that would benefit drilling performance include: bit accelerations for use in controlling bit bounce and improving rock penetration rates and bit life; downhole fluid pressures for use in the management of drilling hydraulics and improved diagnosis of lost circulation and gas kicks; hole trajectory for use in reducing directional

Effects of a Short Drilling Implant Protocol on Osteotomy Site Temperature and Drill Torque.

Science.gov (United States)

Mihali, Sorin G; Canjau, Silvana; Cernescu, Anghel; Bortun, Cristina M; Wang, Hom-Lay; Bratu, Emanuel

2018-02-01

To establish a protocol for reducing the drilling sequence during implant site preparation based on temperature and insertion torque. The traditional conventional drilling sequence (used several drills with 0.6-mm increment each time) was compared with the proposed short drilling protocol (only used 2 drills: initial and final drill). One hundred drilling osteotomies were performed in bovine and porcine bones. Sets of 2 osteotomy sites were created in 5 bone densities using 2 types of drilling protocols. Thermographic pictures were captured throughout all drilling procedures and analyzed using ThermaCAM Researcher Professional 2.10. Torque values were determined during drilling by measuring electrical input and drill speed. There were statistically significant differences in bone temperature between the conventional and short drilling protocols during implant site preparation (analysis of variance P = 0.0008). However, there were no significant differences between the 2 types of drilling protocols for both implant diameters. Implant site preparation time was significantly reduced when using the short drilling protocol compared with the conventional drilling protocol (P drilling protocol proposed herein may represent a safe approach for implant site preparation.

Barite: a case study of import reliance on an essential material for oil and gas exploration and development drilling

Science.gov (United States)

Bleiwas, Donald I.; Miller, M. Michael

2015-01-01

Global dependence on a limited number of countries for specific mineral commodities could lead to sudden supply disruptions for the United States, and barite is one such commodity. Analyses of barite supply amounts and sources for the United States are demonstrative of mineral commodities on which the country is import reliant. Mineral commodity trade flows can be analyzed more easily than import reliances for commodities in which U.S. domestic demand is primarily met by materials contained within manufactured products, as with the rare-earth elements in cellular phones and computers. Barite plays an essential role as a weighting material in drilling muds used in oil and gas drilling, primarily to prevent the explosive release of gas and oil during drilling. The Nation’s efforts to become more energy independent are based largely on the domestic oil and gas industry’s ability to explore and develop onshore and offshore fuel deposits. These activities include increased efforts by the United States to locate and recover oil and gas within unconventional deposits, such as those in the Bakken, Eagle Ford, and Marcellus Formations, using advanced drilling technologies.

Managing Geothermal Exploratory Drilling Risks Drilling Geothermal Exploration and Delineation Wells with Small-Footprint Highly Portable Diamond Core Drills

Science.gov (United States)

Tuttle, J.; Listi, R.; Combs, J.; Welch, V.; Reilly, S.

2012-12-01

Small hydraulic core rigs are highly portable (truck or scow-mounted), and have recently been used for geothermal exploration in areas such as Nevada, California, the Caribbean Islands, Central and South America and elsewhere. Drilling with slim diameter core rod below 7,000' is common, with continuous core recovery providing native-state geological information to aid in identifying the resource characteristics and boundaries; this is a highly cost-effective process. Benefits associated with this innovative exploration and delineation technology includes the following: Low initial Capital Equipment Cost and consumables costs Small Footprint, reducing location and road construction, and cleanup costs Supporting drill rod (10'/3meter) and tools are relatively low weight and easily shipped Speed of Mobilization and rig up Reduced requirements for support equipment (cranes, backhoes, personnel, etc) Small mud systems and cementing requirements Continuous, simplified coring capability Depth ratings comparable to that of large rotary rigs (up to ~10,000'+) Remote/small-location accessible (flown into remote areas or shipped in overseas containers) Can be scow or truck-mounted This technical presentation's primary goal is to share the technology of utilizing small, highly portable hydraulic coring rigs to provide exploratory drilling (and in some cases, production drilling) for geothermal projects. Significant cost and operational benefits are possible for the Geothermal Operator, especially for those who are pursuing projects in remote locations or countries, or in areas that are either inaccessible or in which a small footprint is required. John D. Tuttle Sinclair Well Products jtuttle@sinclairwp.com

Rapid Response Fault Drilling Past, Present, and Future

Directory of Open Access Journals (Sweden)

Demian M. Saffer

2009-09-01

Full Text Available New information about large earthquakes can be acquired by drilling into the fault zone quickly following a large seismic event. Specifically, we can learn about the levels of friction and strength of the fault which determine the dynamic rupture, monitor the healing process of the fault, record the stress changes that trigger aftershocks and capture important physical and chemical properties of the fault that control the rupture process. These scientific and associated technical issues were the focus of a three-day workshop on Rapid Response Fault Drilling: Past, Present, and Future, sponsored by the International Continental Scientific Drilling Program (ICDP and the Southern California Earthquake Center (SCEC. The meeting drewtogether forty-four scientists representing ten countries in Tokyo, Japan during November 2008. The group discussed the scientific problems and how they could be addressed through rapid response drilling. Focused talks presented previous work on drilling after large earthquakes and in fault zones in general, as well as the state of the art of experimental techniques and measurement strategies. Detailed discussion weighed the tradeoffs between rapid drilling andthe ability to satisfy a diverse range of scientific objectives. Plausible drilling sites and scenarios were evaluated. This is a shortened summary of the workshop report that discusses key scientific questions, measurement strategies, and recommendations. This report can provide a starting point for quickly mobilizing a drilling program following future large earthquakes. The full report can be seen at http://www.pmc.ucsc.edu/~rapid/.

Impacts of offshore oil industry on the marine biota and mitigating measures; Impactos das atividades offshore da industria do petroleo sobre a comunidade biologica marinha e as medidas mitigadoras

Energy Technology Data Exchange (ETDEWEB)

Cotta, Patricia S. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Unidade de Negocio SMS

2004-07-01

The growth of industrialization is generating an increase in environmental change, mainly in the marine environment.The petroleum industry is performing a great search for petroleum fields resulting in a transference from land activity to the sea and to deeper water layers (offshore). The offshore exploration in Brazil corresponds to 80% of the national petroleum production. This increasing production is raising questions about the impacts caused by its activities on aquatic biological communities. The potentially impactant activities of the petroleum industry are oil exploration, drilling and production. To mitigate and to accompany the potential environment impacts of its activities, the petroleum industry is implementing environmental monitoring projects whose guidelines directives are established by the responsible environmental agency. These projects aim at accompanying the effects of the continuos discharge of effluents on the local oceanic ecosystem through environmental characterization before, during and after the production activities, physical and chemical characterizations of sea water, qualitative and quantitative analyses of the biological monitoring, accompaniment of the environmental conditions during all oil rig activity and characterization of produced water, through physical, chemical and eco toxicological assays. (author)

Research progress of anti-icing/deicing technologies for polar ships and offshore platforms

Directory of Open Access Journals (Sweden)

XIE Qiang

2017-01-01

Full Text Available The polar regions present adverse circumstances of high humidity and strong air-sea exchange. As such, the surfaces of ships and platforms (oil exploiting and drilling platforms serving in polar regions can easily be frozen by ice accretion, which not only affects the operation of the equipment but also threatens safety. This paper summarizes the status of the anti-icing/deicing technologies of both China and abroad for polar ships and offshore platforms, and introduces the various effects of ice accretion on polar ships and offshore platforms, and the resulting safety impacts. It then reviews existing anti-icing/deicing technologies and methods of both China and abroad, including such active deicing methods as electric heating, infrared heating and ultrasonic guided wave deicing, as well as such passive deicing methods as super hydrophobic coating, sacrificial coating, aqueous lubricating layer coating and low cross-link density (with interfacial slippage coating, summarizes their applicability to polar ships and offshore platforms, and finally discusses their advantages/disadvantages.

Lake Michigan Offshore Wind Feasibility Assessment

Energy Technology Data Exchange (ETDEWEB)

Boezaart, Arnold [GVSU; Edmonson, James [GVSU; Standridge, Charles [GVSU; Pervez, Nahid [GVSU; Desai, Neel [University of Michigan; Williams, Bruce [University of Delaware; Clark, Aaron [GVSU; Zeitler, David [GVSU; Kendall, Scott [GVSU; Biddanda, Bopi [GVSU; Steinman, Alan [GVSU; Klatt, Brian [Michigan State University; Gehring, J. L. [Michigan State University; Walter, K. [Michigan State University; Nordman, Erik E. [GVSU

2014-06-30

The purpose of this project was to conduct the first comprehensive offshore wind assessment over Lake Michigan and to advance the body of knowledge needed to support future commercial wind energy development on the Great Lakes. The project involved evaluation and selection of emerging wind measurement technology and the permitting, installation and operation of the first mid-lake wind assessment meteorological (MET) facilities in Michigan’s Great Lakes. In addition, the project provided the first opportunity to deploy and field test floating LIDAR and Laser Wind Sensor (LWS) technology, and important research related equipment key to the sitting and permitting of future offshore wind energy development in accordance with public participation guidelines established by the Michigan Great Lakes Wind Council (GLOW). The project created opportunities for public dialogue and community education about offshore wind resource management and continued the dialogue to foster Great Lake wind resource utilization consistent with the focus of the GLOW Council. The technology proved to be effective, affordable, mobile, and the methods of data measurement accurate. The public benefited from a substantial increase in knowledge of the wind resources over Lake Michigan and gained insights about the potential environmental impacts of offshore wind turbine placements in the future. The unique first ever hub height wind resource assessment using LWS technology over water and development of related research data along with the permitting, sitting, and deployment of the WindSentinel MET buoy has captured public attention and has helped to increase awareness of the potential of future offshore wind energy development on the Great Lakes. Specifically, this project supported the acquisition and operation of a WindSentinel (WS) MET wind assessment buoy, and associated research for 549 days over multiple years at three locations on Lake Michigan. Four research objectives were defined for the

Comments on new technical and economic data available for EPA's proposed offshore oil and gas discharge guidelines and standards

International Nuclear Information System (INIS)

1989-01-01

The purpose of this paper is to provide comments on the Environmental Protection Agency (EPA) Notice in the Federal Register entitled, ''Oil and Gas Extraction Point Source Category, Offshore Subcategory; Effluent Limitations Guidelines and New Source Performance Standards; New Information and Request or Comments'' (53 FR 41356; October 21, 1988). This Notice announces the availability of new technical, economic and environmental assessment information relating to the development of Best Available Technology economically achievable (BAT and New Source Performance Standards (NSPS) regulations under the Clean Water Act governing the discharge of drilling fluids (muds) and drill cuttings from offshore oil and gas facilities. The Notice is part of a rulemaking process which formally began with the initial release of rules in August 1985 and which incorporates numerous comments and additional data received subsequent to the release of the 1985 rules. The comments in this paper will concentrate on the following five issues: Estimated project impacts are misrepresented by assuming weighted-average incremental costs of regulation. Economic impacts are inaccurate, since annual compliance costs will likely affect the number of wells drilled, by the effect of compliance costs on project economics and the reduction in industry cash flows on capital available for drilling. Initial well productivity assumptions for various scenarios do not vary with field size. The assumed lease costs, which are based on historical data, do not accurately reflect the future value of leases. The experimental decline rates assumed for the Pacific are too high

Measurement of residual stress fields in FHPP welding: a comparison between DSPI combined with hole-drilling and neutron diffraction

Science.gov (United States)

Viotti, Matias R.; Albertazzi, Armando; Staron, Peter; Pisa, Marcelo

2013-04-01

This paper shows a portable device to measure mainly residual stress fields outside the optical bench. This system combines the traditional hole drilling technique with Digital Speckle Pattern Interferometry. The novel feature of this device is the high degree of compaction since only one base supports simultaneously the measurement module and the hole-drilling device. The portable device allows the measurement of non-uniform residual stresses in accordance with the ASTM standard. In oil and gas offshore industries, alternative welding procedures among them, the friction hydro pillar processing (FHPP) is highlighted and nowadays is an important maintenance tool since it has the capability to produce structure repairs without risk of explosions. In this process a hole is drilled and filled with a consumable rod of the same material. The rod, which could be cylindrical or conical, is rotated and pressed against the hole, leading to frictional heating. In order to assess features about the residual stress distribution generated by the weld into the rod as well as into the base material around the rod, welded samples were evaluated by neutron diffraction and by the hole drilling technique having a comparison between them. For the hole drilling technique some layers were removed by using electrical discharge machining (EDM) after diffraction measurements in order to assess the bulk stress distribution. Results have shown a good agreement between techniques.

Assessing the Relative Mobility of Submarine Landslides from Deposit Morphology and Physical Properties: an Example from Nankai Trough, Offshore Japan

Science.gov (United States)

Sawyer, D.; Moore, Z. T.

2014-12-01

A prominent landslide deposit in the Slope Basin seaward of the Megasplay Fault in the Nankai Trough was emplaced by a high-mobility landslide based on analysis of physical properties and seismic geomorphology. Slide acceleration is a critical variable that determines amplitude of slide-generated tsunami but is many times a variable with large uncertainty. In controlled laboratory experiments, the ratio of the shear stress to yield strength, defined as the Flow Factor, controls a wide spectrum of mass movement styles from slow, retrogressive failure to rapid, liquefied flows. We apply the laboratory Flow Factor approach to a natural landslide in the Nankai Trough by constraining pre-failure particle size analysis and porosity. Several mass transport deposits (MTDs), were drilled and cored at Site C0021 in the Nankai Trough during Integrated Ocean Drilling Program (IODP) Expedition 338. The largest, MTD-6, occurs at 133-176 meters below seafloor and occurred approximately 0.87 Mya. Slide volume is 2 km3, transport distance is 5 km, and average deposit thickness is 50 m (maximum 180 m). Pre-failure water content was estimated from shallow sediments at Site C0018 (porosity = 72%). The average grain size distribution is 39% clay-sized, 58% silt-sized, and 3% sand-size particles as determined by hydrometer analyses of the MTD. Together, the porosity and clay fraction predict a Flow Factor of approximately 4, which corresponds to a relatively high mobility slide. We interpret this result to indicate the landslide that created MTD-6 was a single event that transported the slide mass relatively rapidly as opposed to a slow, episodic landslide event. This is supported by the observation of a completely evacuated source area with no remnant blocks or retrogressive headscarp and the internally chaotic seismic facies with large entrained blocks. Future works will focus on the tsunamigenic potential of this high mobility slide. This approach can be extended to other field

Development of computational tool to interpret real time Pd (Pressure While Drilling) data; Desenvolvimento de ferramenta computacional interpretadora de dados de PWD (Pressure While Drilling) em tempo real

Energy Technology Data Exchange (ETDEWEB)

Gandelman, Roni Abensur; Waldmann, Alex Tadeu de Almeida; Martins, Andre Leibsohn [Centro de Pesquisas da Petrobras (CENPES). Gerencia de Tecnologia de Engenharia de Poco (Brazil)], e-mails: roniag@petrobras.com.br, awaldmann@petrobras.com.br, aleibsohn@petrobras.com.br; Teixeira, Gleber Tacio; Aragao, Atila Fernando Lima [E and P Servicos. Gerencia de Servicos de Poco (Brazil)], e-mail: gleber@petrobras.com.br, atila_aragao@petrobras.com.br; Rezende, Mauricio Seiji; Kern, Eduardo; Maliska Junior, Clovis [Engineering Simulation and Scientific Software (ESSS), (Brazil)], e-mails: mauricio@esss.com.br, kern@esss.com.br, coi@esss.com.br

2008-12-15

Drilling offshore oil wells is a very expensive and complex process, in which all the efforts must be taken to keep the annular pressure between a minimum pressure (pore pressure) and a maximum pressure (fracture pressure) which define the operational window limits. Several phenomena impact the bottom hole annular pressures, such as: ineffective hole cleaning, gel breaking when circulation is resumed, drill string movement (surge and swab), trips, pills displacement, kicks, etc. The correct interpretation of pressure while drilling (PWD) data is a very powerful toll to identify and prevent these phenomena. Nowadays, an expert monitors bottom hole pressures data and identifies undesirable events. The main goal of this project is the development of a computational tool to monitor pressure (and mud logging) data in real time to identify the causes of abnormal pressure variations, helping the operators to take decisions rapidly. Besides that, the tool allows the user to handle PWD data in a flexible architecture. This flexibility allows the incorporation of new methods of events identification as they are developed. The ultimate goals is to obtain a tool which serves both for the key study of the problems and physical, specific phenomena found during drilling, both for real-time monitoring to assist professionals involved in the process. (author)

Microgravity Drill and Anchor System

Science.gov (United States)

Parness, Aaron; Frost, Matthew A.; King, Jonathan P.

2013-01-01

This work is a method to drill into a rock surface regardless of the gravitational field or orientation. The required weight-on-bit (WOB) is supplied by a self-contained anchoring mechanism. The system includes a rotary percussive coring drill, forming a complete sampling instrument usable by robot or human. This method of in situ sample acquisition using micro - spine anchoring technology enables several NASA mission concepts not currently possible with existing technology, including sampling from consolidated rock on asteroids, providing a bolt network for astronauts visiting a near-Earth asteroid, and sampling from the ceilings or vertical walls of lava tubes and cliff faces on Mars. One of the most fundamental parameters of drilling is the WOB; essentially, the load applied to the bit that allows it to cut, creating a reaction force normal to the surface. In every drilling application, there is a minimum WOB that must be maintained for the system to function properly. In microgravity (asteroids and comets), even a small WOB could not be supported conventionally by the weight of the robot or astronaut. An anchoring mechanism would be needed to resist the reactions, or the robot or astronaut would push themselves off the surface and into space. The ability of the system to anchor itself to a surface creates potential applications that reach beyond use in low gravity. The use of these anchoring mechanisms as end effectors on climbing robots has the potential of vastly expanding the scope of what is considered accessible terrain. Further, because the drill is supported by its own anchor rather than by a robotic arm, the workspace is not constrained by the reach of such an arm. Yet, if the drill is on a robotic arm, it has the benefit of not reflecting the forces of drilling back to the arm s joints. Combining the drill with the anchoring feet will create a highly mobile, highly stable, and highly reliable system. The drilling system s anchor uses hundreds of

Well drilling by rotary percussive drill above ground

International Nuclear Information System (INIS)

Sabatier, G.

1987-01-01

Originally, the Well Drilling Section of Cogema used only the diamond core drilling technique. The appearance of independent rotation for compressed air rock drills has led to the use and to the development of this drilling system, as a drill core is not indispensable, when the material of the search is radioactive. During the last few years, hydraulic drills have replaced the compressed air drills and have resulted in a very marked improvement: - of the penetration rates; - of the depth achieved. The Well Drilling Section of Cogema has to drill about 400 km per year with rock drills above ground and holds also the record for depth achieved with this technique, i.e. 400 m in granite. In France, the costs of these types of drilling are for the same depth of the order of one-quarter of the core drilling and half of the drilling with a down-the-hole drill. Cogema has greatly developed the types of well logging which now permits the extension of this type of drilling to the search for other materials than uranium [fr

A comparitive clinical study between self tapping and drill free screws as a source of rigid orthodontic anchorage.

Science.gov (United States)

Gupta, Nishant; Kotrashetti, S M; Naik, Vijay

2012-03-01

Self-tapping miniscrews are commonly being used as a temporary anchorage device for orthodontic purpose. A prerequisite for the insertion of these screws is the preparation of a pilot hole, which is time consuming and may result in damage to nerves, tooth root, drill bit breakage and thermal necrosis of bone. On the other hand the design of drill-free screws enables them to be inserted without drilling. The aim of this prospective study was to compare the stability and clinical response of the soft tissue around the self tapping and drill free screws when used for orthodontic anchorage for en mass retraction of maxillary anterior teeth. The study sample consisted of 20 patients requiring retraction of maxillary anterior teeth. The screws were placed in the alveolar bone between maxillary 2nd premolar and 1st molar bilaterally at the junction of attached gingiva and moveable mucosa. Pilot hole was drilled on the side which was selected for insertion of the self tapping screw under copious irrigation, after which it was inserted. Drill free screw was inserted on the contralateral side without predrilling. All screws were immediately loaded with 150-200 gm of retraction force. Patients were recalled for regular follow up for a period of 6 months. If the screws became mobile or showed any signs of inflammation during the course of the study, they were considered to be a failure. After a period of 6 months an overall success rate of 77.5% was noted. Four self tapping and five drill-free screws failed during the study. There was no statistically significant difference between the two types of screws with respect to success/failure. Mobility was found to be the major cause for the failure. Both self-tapping and the drill-free screws are effective anchorage units. But the latter have an edge over the conventional self-tapping screws because of decrease in operative time, little bone debris, less thermal damage, lower morbidity, and minimal patient discomfort as

Space weather effects on drilling accuracy in the North Sea

Directory of Open Access Journals (Sweden)

S. J. Reay

2005-11-01

Full Text Available The oil industry uses geomagnetic field information to aid directional drilling operations when drilling for oil and gas offshore. These operations involve continuous monitoring of the azimuth and inclination of the well path to ensure the target is reached and, for safety reasons, to avoid collisions with existing wells. Although the most accurate method of achieving this is through a gyroscopic survey, this can be time consuming and expensive. An alternative method is a magnetic survey, where measurements while drilling (MWD are made along the well by magnetometers housed in a tool within the drill string. These MWD magnetic surveys require estimates of the Earth's magnetic field at the drilling location to correct the downhole magnetometer readings. The most accurate corrections are obtained if all sources of the Earth's magnetic field are considered. Estimates of the main field generated in the core and the local crustal field can be obtained using mathematical models derived from suitable data sets. In order to quantify the external field, an analysis of UK observatory data from 1983 to 2004 has been carried out. By accounting for the external field, the directional error associated with estimated field values at a mid-latitude oil well (55° N in the North Sea is shown to be reduced by the order of 20%. This improvement varies with latitude, local time, season and phase of the geomagnetic activity cycle. By accounting for all sources of the field, using a technique called Interpolation In-Field Referencing (IIFR, directional drillers have access to data from a "virtual" magnetic observatory at the drill site. This leads to an error reduction in positional accuracy that is close to matching that of the gyroscopic survey method and provides a valuable independent technique for quality control purposes.

Optimising inflow performance of a long multi-lateral offshore well in low permeability, gas-bearing sandstone: K14-FB 102 case study

Energy Technology Data Exchange (ETDEWEB)

Hands, N. [Shell Canada Ltd., Calgary, AB (Canada); Francis, P. [Shell International Exploration and Production (Netherlands); Whittle, A.; Rajasingam, D. [NAM B. V. (Netherlands)

1998-12-31

Successful completion of the sub-horizontal dual-lateral well, K14-FB 102, to optimize production capacity and reservoir drainage in an offshore gas play in the Dutch sector of the North Sea is described. The two 5-7/8 inch horizontal production intervals were drilled and completed using a rheologically engineered, minimal solids, non-damaging sodium formate brine- based fluid designed as a drill-in fluid for reservoir intervals. The completion was made possible by the selection of the appropriate reservoir drill-in and completion fluid, appropriate level of contingency planning and a fully integrated team approach and custom-made well solution. Inflow performance has matched the performance of cemented and high-performance wells at a much lower cost. It was found that openhole reservoir completion techniques offer relatively inexpensive `fit-for-purpose` well solutions for low permeability sandstone in this region of the North Sea.3 refs., 6 tabs., 7 figs.

Study for increasing micro-drill reliability by vibrating drilling

International Nuclear Information System (INIS)

Yang Zhaojun; Li Wei; Chen Yanhong; Wang Lijiang

1998-01-01

A study for increasing micro-drill reliability by vibrating drilling is described. Under the experimental conditions of this study it is observed, from reliability testing and the fitting of a life-distribution function, that the lives of micro-drills under ordinary drilling follow the log-normal distribution and the lives of micro-drills under vibrating drilling follow the Weibull distribution. Calculations for reliability analysis show that vibrating drilling can increase the lives of micro-drills and correspondingly reduce the scatter of drill lives. Therefore, vibrating drilling increases the reliability of micro-drills

DOE HIGH-POWER SLIM-HOLE DRILLING SYSTEM

Energy Technology Data Exchange (ETDEWEB)

Dr. William C. Maurer; John H. Cohen; J. Chris Hetmaniak; Curtis Leitko

1999-09-01

This project used a systems approach to improve slim-hole drilling performance. A high power mud motor, having a double-length power section, and hybrid PDC/TSP drill bit were developed to deliver maximum horsepower to the rock while providing a long life down hole. This high-power slim-hole drilling system drills much faster than conventional slim-hole motor and bit combinations and holds significant potential to reduce slim-hole drilling costs. The oil and gas industries have been faced with downward price pressures since the 1980s. These pressures are not expected to be relieved in the near future. To maintain profitability, companies have had to find ways to reduce the costs of producing oil and gas. Drilling is one of the more costly operations in the production process. One method to reduce costs of drilling is to use smaller more mobile equipment. Slim holes have been drilled in the past using this principle. These wells can save money not only from the use of smaller drilling equipment, but also from reduced tubular costs. Stepping down even one casing size results in significant savings. However, slim holes have not found wide spread use for three reasons. First, until recently, the price of oil has been high so there were no forces to move the industry in this direction. Second, small roller bits and motors were not very reliable and they drilled slowly, removing much of the economic benefit. The third and final reason was the misconception that large holes were needed everywhere to deliver the desired production. Several factors have changed that will encourage the use of slim holes. The industry now favors any method of reducing the costs of producing oil and gas. In addition, the industry now understands that large holes are not always needed. Gas, in particular, can have high production rates in smaller holes. New materials now make it possible to manufacture improved bits and motors that drill for long periods at high rates. All that remains is to

Drilling a better pair : new technologies in SAGD directional drilling

Energy Technology Data Exchange (ETDEWEB)

Zimmer, C.; Richter, D. [Statoil Canada Ltd., Calgary, AB (Canada); Person, J.; Tilley, J.; Bittar, M. [Halliburton Energy Services, Calgary, AB (Canada)

2010-07-01

The Leismer Demonstration Project (LDP) is the first of 8 proposed major steam assisted gravity drainage (SAGD) projects for Statoil's Kai Kos Dehseh (KKD) asset in the Athabasca oil sands deposit. The bitumen resources are expected to produce approximately 2.2 billion barrels of oil over approximately 35 years with a peak production of 220,000 bbl/day. To date, 23 well pairs have been drilled on 4 drilling pads. The precise placement of well pairs is among the most important factors in a successful SAGD drilling program. The producer well must be placed in relation to the reservoir boundaries. It must also be accurately twinned with the injector well. A strong focus on technological innovation is needed in order to deliver on these high expectations in unconsolidated formations, such as the McMurray oil sands. Lateral SAGD pairs are often drilled with conventional steerable mud motors and logging-while-drilling (LWD) resistivity measurements, but this combination imposes certain limitations in terms of wellbore quality and placement. Several industry firsts were successfully implemented at the Statoil LDP, including a combination of the newest and most cutting-edge directional, measurement, and LWD technology. The keystone of these industry firsts was the use of a soft formation modified, point-the-bit rotary steerable system (RSS), used on 20 horizontal wells. The RRS was combined with an ultra deep azimuthal resistivity sensor to provide precise geosteering along the bottom bed boundary in the producer wells, resulting in improved reservoir capture and reservoir characterization. This paper described the new drilling system and its impact on the progressive future of directional drilling in SAGD. 8 refs., 1 tab., 22 figs.

A self propelled drilling system for hard-rock, horizontal and coiled tube drilling

Energy Technology Data Exchange (ETDEWEB)

Biglin, D.; Wassell, M.

1997-12-31

Several advancements are needed to improve the efficiency and reliability of both hard rock drilling and extended reach drilling. This paper will present a Self Propelled Drilling System (SPDS) which can grip the borehole wall in order to provide a stable platform for the application of weight on bit (WOB) and resisting the reactive torque created by the downhole drilling motor, bit and formation interaction. The system will also dampen the damaging effects of drill string vibration. This tool employs two hydraulically activated anchors (front and rear) to grip the borehole wall, and a two-way thrust mandrel to apply both the drilling force to the bit, and a retraction force to pull the drill string into the hole. Forward drilling motion will commence by sequencing the anchor pistons and thrust mandrel to allow the tool to walk in a stepping motion. The SPDS has a microprocessor to control valve timing, sensing and communication functions. An optional Measurement While Drilling (MWD) interface can provide two-way communication of critical operating parameters such as hydraulic pressure and piston location. This information can then be telemetered to the surface, or used downhole to autonomously control system parameters such as anchor and thrust force or damping characteristics.

46 CFR 108.503 - Relationship to international standards.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Relationship to international standards. 108.503 Section 108.503 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.503 Relationship to international standards. For...

Examination of body burden and taint for Iceland scallop (Chlamys islandica) and American plaice (Hippoglossoides platessoides) near the Terra Nova offshore oil development over ten years of drilling on the Grand Banks of Newfoundland, Canada

Science.gov (United States)

DeBlois, Elisabeth M.; Kiceniuk, Joe W.; Paine, Michael D.; Kilgour, Bruce W.; Tracy, Ellen; Crowley, Roger D.; Williams, Urban P.; Gregory Janes, G.

2014-12-01

This paper presents results of analyses of body burdens of metals and hydrocarbons, and taste tests for taint, in Iceland scallop and American plaice performed as part of the Environmental Effects Monitoring (EEM) program for the Terra Nova offshore oil development (Grand Banks of Newfoundland, Canada). Scallop and plaice were collected in a Study Area located within approximately 1 km of drill centres at Terra Nova and in a Reference Area located approximately 20 km from the development. Samples were collected in 1997 to establish a baseline, and from 2000 to 2010, during drilling periods. Scallop adductor muscle tissue was contaminated with >C10-C21 aliphatic hydrocarbons resembling the drilling fluid in the synthetic drilling mud (SBM) used at Terra Nova in 2000, 2002 and 2004, but contamination of adductor muscle was not noted in 2006, 2008 and 2010. The maximum concentration in muscle was 28 mg/kg wet weight, noted in 2002. Scallop viscera was contaminated with hydrocarbons resembling drilling fluid in SBMs near drill centres in all EEM years except 2010. Viscera contamination with >C10-C21 hydrocarbons gradually decreased from a maximum of 150 mg/kg in 2000, to a maximum of 27 mg/kg in 2008; all values were below the laboratory reporting detection limit of 15 mg/kg in 2010. Therefore, evidence from both muscle and viscera indicates a decrease in tissue hydrocarbon contamination in recent years. Barium, another major constituent in drilling muds, has not been noted in scallop adductor muscles at concentrations above the reporting detection limit, but barium was detected in viscera in baseline and EEM years. The maximum concentration of barium in viscera during baseline sampling was 8 mg/kg. The maximum concentration in EEM years (29 mg/kg) was noted in 2000. The maximum concentration in 2010 was 25 mg/kg. The concentration of metals other than barium in scallop tissues was similar between the Terra Nova Study Area and the Reference Area. Hydrocarbons

Laboratory exposures of invertebrate and vertebrate species to concentrations of IA-35 (Petro-Canada) drill mud fluid, production water, and Hibernia mud cuttings

Energy Technology Data Exchange (ETDEWEB)

Payne, J.; Fancey, L.; Andrews, C.; Meade, J.; Power, F.; Veinot, G. [Department of Fisheries and Oceans, St. John' s, NF (Canada). Science Branch; Lee, K. [Department of Fisheries and Oceans, Mont-Joli, PQ (Canada). Maurice Lamontagne Inst.; Cook, A. [Environment Canada, Moncton, NB (Canada). Environmental Quality Laboratory

2001-04-01

The authors studied the short term effects on brine shrimp nauplii (Artemia franciscana), capelin larvae (Mallotus villosus), marine copepods (Calanus finmarchicus), juvenile yellowtail flounder (Limanda ferruginea) and ctenophores (Pleurobrachius pileus) of synthetic drill mud fluid, produced water and drill mud cuttings. In this report, they presented the data collected, including data on the water solubility of Petro-Canada drill mud fluid IA-35 and metal analysis of production water from the Sable Island Offshore Exploration Project. Low acute toxicity potential for drill mud fluid, production water and Hibernia drill cuttings for the species and life stages tested were revealed. The hypothesis to the effect that wastes pose very little or no risk of an acute toxic nature to the marine environment were reinforced by the results from this study. 5 refs., 25 tabs.

46 CFR 109.564 - Maneuvering characteristics.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Maneuvering characteristics. 109.564 Section 109.564 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.564 Maneuvering characteristics. (a) The master or person in charge of each...

46 CFR 108.235 - Construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Construction. 108.235 Section 108.235 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Construction and Arrangement Helicopter Facilities § 108.235 Construction. (a) Each helicopter deck must be...

46 CFR 108.580 - Personal lifesaving appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Personal lifesaving appliances. 108.580 Section 108.580 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.580 Personal lifesaving appliances. (a) Lifebuoys. Each unit...

46 CFR 108.645 - Markings on lifesaving appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Markings on lifesaving appliances. 108.645 Section 108.645 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.645 Markings on lifesaving appliances. (a...

The offshore petroleum industry: The formative years, 1945-1962

Science.gov (United States)

Kreidler, Tai Deckner

1997-12-01

This dissertation is the first to examine the offshore oil industry that was born in the calm waters of the Gulf of Mexico. It describes the industry's origins and tracks its development as a consequence of a search for new oil frontiers. In addition, it elaborates how the oil industry moved into the marine province using available technology, and was driven by the economic urgency to compete and develop new territories. Enterprising drilling contractors and operators seized the offshore gamble, finding it possible to lower the economic and technological threshold by drawing directly from wartime research and surplus equipment. Though large oil companies had placed its indelible stamp upon the industry, the smaller, independent oil operators set the pace of early offshore development. As a technological frontier, offshore development depended upon creative and unconventional engineering. Unfamiliar marine conditions tested the imagination of oil industry engineering. The unorthodox methods of John Hayward of Barnsdall Oil and R. G. LeTourneau of LeTourneau, Inc. among others transformed the industry by blending petroleum and marine engineering. Grappling with alien marine conditions and lacking formal training, Hayward and LeTourneau merged a century of practical oil field knowledge and petroleum engineering with 2,000 years of shipbuilding experience. The Gulf of Mexico served as a fertile and protective environment for the development of a fledgling industry. With calm waters, lacking the tempestuous and stormy character of the Atlantic Ocean, with a gradual sea-floor slope and saturated with the highly productive salt dome reservoirs, the Gulf became the birth place of the modern offshore oil industry. Within its protective sphere, companies experimented and developed various technical and business adaptations. Operators used technology and business strategies that increased the opportunity for success. In addition, regional academic research institutes arose as

Percussive Augmenter of Rotary Drills for Operating as a Rotary-Hammer Drill

Science.gov (United States)

Aldrich, Jack Barron (Inventor); Bar-Cohen, Yoseph (Inventor); Sherrit, Stewart (Inventor); Badescu, Mircea (Inventor); Bao, Xiaoqi (Inventor); Scott, James Samson (Inventor)

2014-01-01

A percussive augmenter bit includes a connection shaft for mounting the bit onto a rotary drill. In a first modality, an actuator percussively drives the bit, and an electric slip-ring provides power to the actuator while being rotated by the drill. Hammering action from the actuator and rotation from the drill are applied directly to material being drilled. In a second modality, a percussive augmenter includes an actuator that operates as a hammering mechanism that drives a free mass into the bit creating stress pulses that fracture material that is in contact with the bit.

46 CFR 108.665 - Appliances for watertight integrity.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 108.665 Section 108.665 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.665 Appliances for watertight integrity...

Archer Fire and Safety - reducing risk in the offshore

Energy Technology Data Exchange (ETDEWEB)

Todd, K

2000-06-01

Protecting the lives and safety of offshore oil and gas workers is the business of Newfoundland-based Archer Fire and Safety. Originally established as a supplier of industrial materials focusing on the oil and gas industry, the company narrowed its focus in 1996 to fire and safety protection, introduced more specialized fire and safety equipment, and began to explore service opportunities to the industry in addition to the usual consumables. After some anxious few years, the company now operates two SCBA service centres in Newfoundland, in addition to sales and servicing a wide range of fire and safety equipment such as gas, flame and heat detection.The company is constantly on the lookout for new opportunities and has developed a computer-based pricing system which enables them to provide quick response to pricing inquiries, a big advantage in an industry with relatively unsophisticated business practices. The company's emphasis on research and quick response capability enabled the company to anticipate future requirements and to land major contracts first at Bull Arm, and later on the Terra Nova Project. Its reputation for best-in-class products, high quality service and a business-like approach helped to attract other clients such as Terra Nova Alliance, Canship and Schlumberger, and offshore drilling companies like Glomar International and TransOcean Sedco-Forex, with further opportunities in the offing with upcoming projects such as the White Rose and Hebron.Today about 60 per cent of the business is offshore related.

Archer Fire and Safety - reducing risk in the offshore

Energy Technology Data Exchange (ETDEWEB)

Todd, K.

2000-06-01

Protecting the lives and safety of offshore oil and gas workers is the business of Newfoundland-based Archer Fire and Safety. Originally established as a supplier of industrial materials focusing on the oil and gas industry, the company narrowed its focus in 1996 to fire and safety protection, introduced more specialized fire and safety equipment, and began to explore service opportunities to the industry in addition to the usual consumables. After some anxious few years, the company now operates two SCBA service centres in Newfoundland, in addition to sales and servicing a wide range of fire and safety equipment such as gas, flame and heat detection.The company is constantly on the lookout for new opportunities and has developed a computer-based pricing system which enables them to provide quick response to pricing inquiries, a big advantage in an industry with relatively unsophisticated business practices. The company's emphasis on research and quick response capability enabled the company to anticipate future requirements and to land major contracts first at Bull Arm, and later on the Terra Nova Project. Its reputation for best-in-class products, high quality service and a business-like approach helped to attract other clients such as Terra Nova Alliance, Canship and Schlumberger, and offshore drilling companies like Glomar International and TransOcean Sedco-Forex, with further opportunities in the offing with upcoming projects such as the White Rose and Hebron.Today about 60 per cent of the business is offshore related.

First evaluation of foraminiferal metabarcoding for monitoring environmental impact from an offshore oil drilling site

KAUST Repository

Laroche, Olivier

2016-08-29

At present, environmental impacts from offshore oil and gas activities are partly determined by measuring changes in macrofauna diversity. Morphological identification of macrofauna is time-consuming, expensive and dependent on taxonomic expertise. In this study, we evaluated the applicability of using foraminiferal-specific metabarcoding for routine monitoring. Sediment samples were collected along distance gradients from two oil platforms off Taranaki (New Zealand) and their physicochemical properties, foraminiferal environmental DNA/RNA, and macrofaunal composition analyzed. Macrofaunal and foraminiferal assemblages showed similar shifts along impact gradients, but responded differently to environmental perturbations. Macrofauna were affected by hypoxia, whereas sediment grain size appeared to drive shifts in foraminifera. We identified eight foraminiferal molecular operational taxonomic units that have potential to be used as bioindicator taxa. Our results show that metabarcoding represents an effective tool for assessing foraminiferal communities near offshore oil and gas platforms, and that it can be used to complement current monitoring techniques. (C) 2016 Elsevier Ltd. All rights reserved.

First evaluation of foraminiferal metabarcoding for monitoring environmental impact from an offshore oil drilling site

KAUST Repository

Laroche, Olivier; Wood, Susanna A.; Tremblay, Louis A.; Ellis, Joanne; Lejzerowicz, Franck; Pawlowski, Jan; Lear, Gavin; Atalah, Javier; Pochon, Xavier

2016-01-01

At present, environmental impacts from offshore oil and gas activities are partly determined by measuring changes in macrofauna diversity. Morphological identification of macrofauna is time-consuming, expensive and dependent on taxonomic expertise. In this study, we evaluated the applicability of using foraminiferal-specific metabarcoding for routine monitoring. Sediment samples were collected along distance gradients from two oil platforms off Taranaki (New Zealand) and their physicochemical properties, foraminiferal environmental DNA/RNA, and macrofaunal composition analyzed. Macrofaunal and foraminiferal assemblages showed similar shifts along impact gradients, but responded differently to environmental perturbations. Macrofauna were affected by hypoxia, whereas sediment grain size appeared to drive shifts in foraminifera. We identified eight foraminiferal molecular operational taxonomic units that have potential to be used as bioindicator taxa. Our results show that metabarcoding represents an effective tool for assessing foraminiferal communities near offshore oil and gas platforms, and that it can be used to complement current monitoring techniques. (C) 2016 Elsevier Ltd. All rights reserved.

46 CFR 108.241 - Visual aids.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Visual aids. 108.241 Section 108.241 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Construction and Arrangement Helicopter Facilities § 108.241 Visual aids. (a) Each helicopter deck must— (1...

Accessing offshoring advantages

DEFF Research Database (Denmark)

Mykhaylenko, Alona; Motika, Agnes; Wæhrens, Brian Vejrum

2015-01-01

. Assuming that different levels of synergy may exist between particular offshoring strategic decisions (choosing offshore outsourcing or captive offshoring and the type of function) and different offshoring advantages, this work advocates that the actual fact of realization of certain offshoring advantages...

77 FR 26562 - Mobile Offshore Drilling Unit Dynamic Positioning Guidance

Science.gov (United States)

2012-05-04

... questions on viewing the docket, call Renee V. Wright, Program Manager, Docket Operations, telephone 202-366... operators are encouraged to voluntarily report to the Coast Guard reactive changes of DP status from ``green...

Summary of hydrologic testing in Tertiary limestone aquifer, Tenneco offshore exploratory well--Atlantic OCS, lease-block 427 (Jacksonville NH 17-5)

Science.gov (United States)

Johnston, Richard H.; Bush, Peter W.; Krause, Richard E.; Miller, James A.; Sprinkle, Craig L.

1982-01-01

A summary of hydrologic testing in an offshore oil-test well (LB427) drilled for Tenneco, Inc., 55 miles east of Fernandina Beach, Florida, is presented. The interval tested (1,050 to 1,070 feet below sea level) is in a calcarenite that is equivalent to the Ocala Limestone (late Eocene) of onshore Florida and South Georgia. At this site the Ocala forms the highly productive Tertiary limestone aquifer system of the southeastern United States. Pressure-head measurements indicate an equivalent freshwater head of 24 to 29 feet above sea level. These pressure-head measurements and an earlier one made in the nearby JOIDES J- I hole are the only hydraulic head determinations to date in the offshore extensions of any of the aquifers underlying the Atlantic coastal plain. A drill-stem test recovered water samples containing about 7,000 milligrams per liter chloride. However, seawater used in the drilling process apparently contaminated the samples and the formation water is considered slightly fresher. The head and salinity data from the Tenneco well suggest that the sampled interval lies in the transition zone between fresh and seawater in the limestone aquifer. These data, when viewed with similar data from JOIDES J-I, show the transition zone to slope very slightly landward. The interface position is probably intermediate between a position compatible with present-day heads and a position compatible with predevelopment heads.

Energetic aspects and opportunities for reusing water on offshore platforms in Campos Basin, Brazil

OpenAIRE

Duarte, Victor Magalhães; Queiroz, Luciano Matos; Torres, Ednildo Andrade; Kiperstok, Asher

2017-01-01

Abstract In the drilling and production of oil at sea, a large quantity of potable water used is most commonly transported to oil platforms using offshore supply vessels (OSVs). Sea water desalination is used as well, but only in a few oil platforms. To minimize energy consumption, water supply options were studied. The desalination of seawater and the reusing of streams of grey water and black water were evaluated and compared with the characteristics of the current supply via OSVs. In both ...

Scientific results of the Second Gas Hydrate Drilling Expedition in the Ulleung Basin (UBGH2)

Science.gov (United States)

Ryu, Byong-Jae; Collett, Timothy S.; Riedel, Michael; Kim, Gil-Young; Chun, Jong-Hwa; Bahk, Jang-Jun; Lee, Joo Yong; Kim, Ji-Hoon; Yoo, Dong-Geun

2013-01-01

As a part of Korean National Gas Hydrate Program, the Second Ulleung Basin Gas Hydrate Drilling Expedition (UBGH2) was conducted from 9 July to 30 September, 2010 in the Ulleung Basin, East Sea, offshore Korea using the D/V Fugro Synergy. The UBGH2 was performed to understand the distribution of gas hydrates as required for a resource assessment and to find potential candidate sites suitable for a future offshore production test, especially targeting gas hydrate-bearing sand bodies in the basin. The UBGH2 sites were distributed across most of the basin and were selected to target mainly sand-rich turbidite deposits. The 84-day long expedition consisted of two phases. The first phase included logging-while-drilling/measurements-while-drilling (LWD/MWD) operations at 13 sites. During the second phase, sediment cores were collected from 18 holes at 10 of the 13 LWD/MWD sites. Wireline logging (WL) and vertical seismic profile (VSP) data were also acquired after coring operations at two of these 10 sites. In addition, seafloor visual observation, methane sensing, as well as push-coring and sampling using a Remotely Operated Vehicle (ROV) were conducted during both phases of the expedition. Recovered gas hydrates occurred either as pore-filling medium associated with discrete turbidite sand layers, or as fracture-filling veins and nodules in muddy sediments. Gas analyses indicated that the methane within the sampled gas hydrates is primarily of biogenic origin. This paper provides a summary of the operational and scientific results of the UBGH2 expedition as described in 24 papers that make up this special issue of the Journal of Marine and Petroleum Geology.

Real Time Seismic Prediction while Drilling

Science.gov (United States)

Schilling, F. R.; Bohlen, T.; Edelmann, T.; Kassel, A.; Heim, A.; Gehring, M.; Lüth, S.; Giese, R.; Jaksch, K.; Rechlin, A.; Kopf, M.; Stahlmann, J.; Gattermann, J.; Bruns, B.

2009-12-01

Efficient and safe drilling is a prerequisite to enhance the mobility of people and goods, to improve the traffic as well as utility infrastructure of growing megacities, and to ensure the growing energy demand while building geothermal and in hydroelectric power plants. Construction within the underground is often building within the unknown. An enhanced risk potential for people and the underground building may arise if drilling enters fracture zones, karsts, brittle rocks, mixed solid and soft rocks, caves, or anthropogenic obstacles. Knowing about the material behavior ahead of the drilling allows reducing the risk during drilling and construction operation. In drilling operations direct observations from boreholes can be complemented with geophysical investigations. In this presentation we focus on “real time” seismic prediction while drilling which is seen as a prerequisite while using geophysical methods in modern drilling operations. In solid rocks P- and S-wave velocity, refraction and reflection as well as seismic wave attenuation can be used for the interpretation of structures ahead of the drilling. An Integrated Seismic Imaging System (ISIS) for exploration ahead of a construction is used, where a pneumatic hammer or a magnetostrictive vibration source generate repetitive signals behind the tunneling machine. Tube waves are generated which travel along the tunnel to the working face. There the tube waves are converted to mainly S- but also P-Waves which interact with the formation ahead of the heading face. The reflected or refracted waves travel back to the working front are converted back to tube waves and recorded using three-component geophones which are fit into the tips of anchor rods. In near real time, the ISIS software allows for an integrated 3D imaging and interpretation of the observed data, geological and geotechnical parameters. Fracture zones, heterogeneities, and variations in the rock properties can be revealed during the drilling

Healthy offshore workforce? A qualitative study on offshore wind employees' occupational strain, health, and coping.

Science.gov (United States)

Mette, Janika; Velasco Garrido, Marcial; Harth, Volker; Preisser, Alexandra M; Mache, Stefanie

2018-01-23

Offshore work has been described as demanding and stressful. Despite this, evidence regarding the occupational strain, health, and coping behaviors of workers in the growing offshore wind industry in Germany is still limited. The purpose of our study was to explore offshore wind employees' perceptions of occupational strain and health, and to investigate their strategies for dealing with the demands of offshore work. We conducted 21 semi-structured telephone interviews with employees in the German offshore wind industry. The interviews were transcribed and analyzed in a deductive-inductive approach following Mayring's qualitative content analysis. Workers generally reported good mental and physical health. However, they also stated perceptions of stress at work, fatigue, difficulties detaching from work, and sleeping problems, all to varying extents. In addition, physical health impairment in relation to offshore work, e.g. musculoskeletal and gastrointestinal complaints, was documented. Employees described different strategies for coping with their job demands. The strategies comprised of both problem and emotion-focused approaches, and were classified as either work-related, health-related, or related to seeking social support. Our study is the first to investigate the occupational strain, health, and coping of workers in the expanding German offshore wind industry. The results offer new insights that can be utilized for future research in this field. In terms of practical implications, the findings suggest that measures should be carried out aimed at reducing occupational strain and health impairment among offshore wind workers. In addition, interventions should be initiated that foster offshore wind workers' health and empower them to further expand on effective coping strategies at their workplace.

Depths of controlled drillings by means of underground drives; Teufen von gesteuerten Bohrungen mittels Untertageantrieben

Energy Technology Data Exchange (ETDEWEB)

Hengevoss, Charly [Weatherford Ukraine LLC, Kiev (Ukraine); Homrighausen, Reiner [BAUER Resources GmbH, Schrobenhausen (Germany)

2013-03-01

Today, the most modern directional drilling technology not only is used in case of very deep drillings (deeper or longer than 2,000 meter) by means of deep-level drilling rigs, but also with small, highly mobile universal drilling rigs. Thus, drilling costs are reduced, and unconventional hydrocarbons (methane gas - oil shale and shale gas) deposits are explores economically. Furthermore, known near-surface petroleum deposits in Northern Germany as well as in other parts of the Earth (such as in Romania, the U.S.A. or in Canada) which extraction of petroleum is very low already are interesting economically. Furthermore, today it is possible to investigate with controlled drillings more economically and with more safe sites for a possibly final storage of highly radioactive wastes. Controlled drillings may give an answer to geotechnical questions on highly inaccessible on optimum points for drilling wells in order to plan underground cavities or to investigate tunnel axes geotechnical or hydrological.

46 CFR 109.555 - Propulsion boilers.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Propulsion boilers. 109.555 Section 109.555 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.555 Propulsion boilers. The master or person in charge and the engineer in charge shall...

46 CFR 108.223 - Guards on exposed equipment.

Science.gov (United States)

2010-10-01

... have hand covers, guards, or rails installed on all belts, gears, shafts, pulleys, sprockets, spindles... 46 Shipping 4 2010-10-01 2010-10-01 false Guards on exposed equipment. 108.223 Section 108.223 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN...

Addressing submarine geohazards through scientific drilling

Science.gov (United States)

Camerlenghi, A.

2009-04-01

Natural submarine geohazards (earthquakes, volcanic eruptions, landslides, volcanic island flank collapses) are geological phenomena originating at or below the seafloor leading to a situation of risk for off-shore and on-shore structures and the coastal population. Addressing submarine geohazards means understanding their spatial and temporal variability, the pre-conditioning factors, their triggers, and the physical processes that control their evolution. Such scientific endeavour is nowadays considered by a large sector of the international scientific community as an obligation in order to contribute to the mitigation of the potentially destructive societal effects of submarine geohazards. The study of submarine geohazards requires a multi-disciplinary scientific approach: geohazards must be studied through their geological record; active processes must be monitored; geohazard evolution must be modelled. Ultimately, the information must be used for the assessment of vulnerability, risk analysis, and development of mitigation strategies. In contrast with the terrestrial environment, the oceanic environment is rather hostile to widespread and fast application of high-resolution remote sensing techniques, accessibility for visual inspection, sampling and installation of monitoring stations. Scientific Drilling through the IODP (including the related pre site-survey investigations, sampling, logging and in situ measurements capability, and as a platform for deployment of long term observatories at the surface and down-hole) can be viewed as the centre of gravity of an international, coordinated, multi-disciplinary scientific approach to address submarine geohazards. The IODP Initial Science Plan expiring in 2013 does not address openly geohazards among the program scientific objectives. Hazards are referred to mainly in relation to earthquakes and initiatives towards the understanding of seismogenesis. Notably, the only drilling initiative presently under way is the

Automatic real time drilling support on Ekofisk utilizing eDrilling

Energy Technology Data Exchange (ETDEWEB)

Rommetveit, Rolv; Bjorkevoll, Knut S.; Halsey, George W.; Kluge, Roald; Molde, Dag Ove; Odegard, Sven Inge [SINTEF Petroleum Research, Trondheim (Norway); Herbert, Mike [HITEC Products Drilling, Stavanger (Norway); ConocoPhillips Norge, Stavanger (Norway)

2008-07-01

eDrilling is a new and innovative system for real time drilling simulation, 3D visualization and control from a remote drilling expert centre. The concept uses all available real time drilling data (surface and downhole) in combination with real time modelling to monitor and optimize the drilling process. This information is used to visualize the wellbore in 3D in real time. eDrilling has been implemented in an Onshore Drilling Center in Norway. The system is composed of the following elements, some of which are unique and ground-breaking: an advanced and fast Integrated Drilling Simulator which is capable to model the different drilling sub-processes dynamically, and also the interaction between these sub-processes in real time; automatic quality check and corrections of drilling data; making them suitable for processing by computer models; real time supervision methodology for the drilling process using time based drilling data as well as drilling models / the integrated drilling simulator; methodology for diagnosis of the drilling state and conditions. This is obtained from comparing model predictions with measured data. Advisory technology for more optimal drilling. A Virtual Wellbore, with advanced visualization of the downhole process. Dat low and computer infrastructure. e-Drilling has been implemented in an Onshore Drilling Center on Ekofisk in Norway. The system is being used on drilling operations, and experiences from its use are presented. The supervision and diagnosis functionalities have been useful in particular, as the system has given early warnings on ECD and friction related problems. This paper will present the eDrilling system as well as experiences from its use. (author)

Deep drilling KLX 02. Drilling and documentation of a 1700 m deep borehole at Laxemar, Sweden

Energy Technology Data Exchange (ETDEWEB)

Andersson, O [VBB VIAK AB, Malmoe (Sweden)

1994-08-01

In this report the preparation and execution of the deep core drilling KLX 02 is described. The hole was drilled with the wireline methods, NQ dimension (diameter 76 mm), to a final depth of 1700.5 m. Prior to core drilling a diameter 215 mm pilot hole was pre drilled to 200 m with controlled hammer drilling (DTH). In this hole casing and air-lift equipment was installed with the aim to support the circulation of drilling fluid. During core drilling there was a measurement of major drilling parameters and drilling fluid in and out of hole. As a fluid tracer uranine was used. Each 300 m of core drilling air-lift pump tests were performed. After completion a flow-meter log was run to finalize the project phase. It can be concluded that both the pre drilling and core drilling methods used proved to be successful. No severe technical problem occurred. However, potential risks have been pointed at in the report. The air-lift system functioned only partly and has to be modified for further use. Also the technique for monitoring of drilling parameters needs improvement as does the method for air-lift pump tests with packer. The organisation model for planning and realization functioned satisfactory and can be recommended for similar future projects. 9 refs, numerous tabs and figs.

Deep drilling KLX 02. Drilling and documentation of a 1700 m deep borehole at Laxemar, Sweden

International Nuclear Information System (INIS)

Andersson, O.

1994-08-01

In this report the preparation and execution of the deep core drilling KLX 02 is described. The hole was drilled with the wireline methods, NQ dimension (diameter 76 mm), to a final depth of 1700.5 m. Prior to core drilling a diameter 215 mm pilot hole was pre drilled to 200 m with controlled hammer drilling (DTH). In this hole casing and air-lift equipment was installed with the aim to support the circulation of drilling fluid. During core drilling there was a measurement of major drilling parameters and drilling fluid in and out of hole. As a fluid tracer uranine was used. Each 300 m of core drilling air-lift pump tests were performed. After completion a flow-meter log was run to finalize the project phase. It can be concluded that both the pre drilling and core drilling methods used proved to be successful. No severe technical problem occurred. However, potential risks have been pointed at in the report. The air-lift system functioned only partly and has to be modified for further use. Also the technique for monitoring of drilling parameters needs improvement as does the method for air-lift pump tests with packer. The organisation model for planning and realization functioned satisfactory and can be recommended for similar future projects. 9 refs, numerous tabs and figs

46 CFR 108.443 - Controls and valves.

Science.gov (United States)

2010-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Fire Extinguishing Systems Fixed Carbon Dioxide Fire Extinguishing Systems § 108.443 Controls and valves. (a) At least one control for operating a CO2 system must be outside the space or spaces that the...

Drilling of bone: A comprehensive review

Science.gov (United States)

Pandey, Rupesh Kumar; Panda, S.S.

2013-01-01

Background Bone fracture treatment usually involves restoring of the fractured parts to their initial position and immobilizing them until the healing takes place. Drilling of bone is common to produce hole for screw insertion to fix the fractured parts for immobilization. Orthopaedic drilling during surgical process causes increase in the bone temperature and forces which can cause osteonecrosis reducing the stability and strength of the fixation. Methods A comprehensive review of all the relevant investigations carried on bone drilling is conducted. The experimental method used, results obtained and the conclusions made by the various researchers are described and compared. Result Review suggests that the further improvement in the area of bone drilling is possible. The systematic review identified several consequential factors (drilling parameters and drill specifications) affecting bone drilling on which there no general agreement among investigators or are not adequately evaluated. These factors are highlighted and use of more advanced methods of drilling is accentuated. The use of more precise experimental set up which resembles the actual situation and the development of automated bone drilling system to minimize human error is addressed. Conclusion In this review, an attempt has been made to systematically organize the research investigations conducted on bone drilling. Methods of treatment of bone fracture, studies on the determination of the threshold for thermal osteonecrosis, studies on the parameters influencing bone drilling and methods of the temperature measurement used are reviewed and the future work for the further improvement of bone drilling process is highlighted. PMID:26403771

Appreciation of environmental risks analysis methodologies in the offshore well drilling activities; Analise de metodologias na avaliacao de riscos ambientais relacionados as atividades de perfuracao de pocos maritimos

Energy Technology Data Exchange (ETDEWEB)

Zampolli, Daniella M. [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil); Morooka, Celso K. [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Engenharia de Petroleo

2004-07-01

Nowadays, the projects of products and processes are supposed to integrate environmental risks criteria, in addition to their inherent operation impacts. Industrial activities, in general, generate risks to the environment, and, in case of incidents occurrence, many of the possible consequences can be translated into serious impacts. The Risk Analysis is destined to act as a decision tool in the environmental area, and therefore, the use of one of these during the project phase of an enterprise becomes important, aiming the guarantee of the system reliability. The present article has the purpose of analyzing methodologies that are being employed for the environmental risk analysis, as well as usual procedures applied in the oil industry, specially for the offshore wells drilling, evaluating and discussing their peculiarities and possible improvement. It was intended to obtain a general overview of risk analysis methodologies, with the objective of verifying the existence of some characteristics that would positively contribute for the knowledge of the inherent risks in the activities of petroleum installations, where this kind of learning is something extremely technically necessary and legally mandatory. (author)

New drilling optimization technologies make drilling more efficient

Energy Technology Data Exchange (ETDEWEB)

Chen, D.C.-K. [Halliburton Energy Services, Calgary, AB (Canada). Sperry Division

2004-07-01

Several new technologies have been adopted by the upstream petroleum industry in the past two decades in order to optimize drilling operations and improve drilling efficiency. Since financial returns from an oil and gas investment strongly depend on drilling costs, it is important to reduce non-productive time due to stuck pipes, lost circulation, hole cleaning and well bore stability problems. The most notable new technologies are the use of computer-based instrumentation and data acquisition systems, integrated rig site systems and networks, and Measurement-While-Drilling and Logging-While-Drilling (MWD/LWD) systems. Drilling optimization should include solutions for drillstring integrity, hydraulics management and wellbore integrity. New drilling optimization methods emphasize information management and real-time decision making. A recent study for drilling in shallow water in the Gulf of Mexico demonstrates that trouble time accounts for 25 per cent of rig time. This translates to about $1.5 MM U.S. per well. A reduction in trouble time could result in significant cost savings for the industry. This paper presents a case study on vibration prevention to demonstrate how the drilling industry has benefited from new technologies. 13 refs., 10 figs.

46 CFR 108.471 - Water pump.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Water pump. 108.471 Section 108.471 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Fire Extinguishing Systems Foam Extinguishing Systems § 108.471 Water pump. Each water pump in a foam extinguishing...

A New Coordinated Voltage Control Scheme for Offshore AC Grid of HVDC Connected Offshore Wind Power Plants

DEFF Research Database (Denmark)

Sakamuri, Jayachandra N.; Cutululis, Nicolaos Antonio; Rather, Zakir Hussain

2015-01-01

This paper proposes a coordinated voltage control scheme (CVCS) which enhances the voltage ride through (VRT) capability of an offshore AC grid comprised of a cluster of offshore wind power plants (WPP) connected through AC cables to the offshore voltage source converter based high voltage DC (VSC......-HVDC) converter station. Due to limited short circuit power contribution from power electronic interfaced variable speed wind generators and with the onshore main grid decoupled by the HVDC link, the offshore AC grid becomes more vulnerable to dynamic voltage events. Therefore, a short circuit fault...... in the offshore AC Grid is likely to have significant implications on the voltage of the offshore AC grid, hence on the power flow to the onshore mainland grid. The proposed CVCS integrates individual local reactive power control of wind turbines and of the HVDC converter with the secondary voltage controller...

Offshore field development. Statfjord - a geologist's dream: an economist's nightmare

Energy Technology Data Exchange (ETDEWEB)

1980-09-01

On September 3, 1980, the water injection module was lifted on board the Statfjord A platform. That marks the completion of the platform, a giant 3,000,000 bpd capacity monster of an offshore structure, carrying a price tag of $1.5 billion. Two more such giants are scheduled to follow, each costing approximately $2 billion in the North Sea's largest and most expensive offshore field development ever. Oil wells in the Statfjord field, the largest North Sea field to date, are now producing at up to 30,000 bpd each. The reservoir proves particularly open, and the filling of it is extremely good. Wells have produced up to 40,000 bpd, but with that kind of flow, sand problems occur. Gravel packs have had to be installed in several of the wells. Mobil's Dallas facilities have uncovered the fact that now dominates the Norwegian North Sea scene, i.e., the cut off point for gas reinjection into the Statfjord sand is late 1985. After that point a possible breakthrough of gas could block the oil or even damage the reservoir if reinjection is continued.

46 CFR 108.499 - Fire axes.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Fire axes. 108.499 Section 108.499 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Fire Extinguishing Systems Miscellaneous Firefighting Equipment § 108.499 Fire axes. Each unit must have at least two...

46 CFR 109.521 - Cranes: General.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Cranes: General. 109.521 Section 109.521 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Cranes § 109.521 Cranes: General. The master or person in charge shall ensure that each crane is operated and...

Test plan for core sampling drill bit temperature monitor

International Nuclear Information System (INIS)

Francis, P.M.

1994-01-01

At WHC, one of the functions of the Tank Waste Remediation System division is sampling waste tanks to characterize their contents. The push-mode core sampling truck is currently used to take samples of liquid and sludge. Sampling of tanks containing hard salt cake is to be performed with the rotary-mode core sampling system, consisting of the core sample truck, mobile exhauster unit, and ancillary subsystems. When drilling through the salt cake material, friction and heat can be generated in the drill bit. Based upon tank safety reviews, it has been determined that the drill bit temperature must not exceed 180 C, due to the potential reactivity of tank contents at this temperature. Consequently, a drill bit temperature limit of 150 C was established for operation of the core sample truck to have an adequate margin of safety. Unpredictable factors, such as localized heating, cause this buffer to be so great. The most desirable safeguard against exceeding this threshold is bit temperature monitoring . This document describes the recommended plan for testing the prototype of a drill bit temperature monitor developed for core sampling by Sandia National Labs. The device will be tested at their facilities. This test plan documents the tests that Westinghouse Hanford Company considers necessary for effective testing of the system

Synthetic-based fluid replacement: excellent drilling efficiency and imaging evaluation achieved with inhibitive water-based fluid

Energy Technology Data Exchange (ETDEWEB)

Mendonca, Ricardo; Fernandez, Jovan Andrade [PETROBRAS, Rio de Janeiro, RJ (Brazil); Anderson, Tom; Loureiro, Mario; Pereira, Alex; Shah, Fayyaz [Halliburton Baroid, Aracaju, SE (Brazil)

2004-07-01

The highly reactive Calumbi shale is encountered in wells drilled by PETROBRAS in the Sergipe area. Normally an invert emulsion fluid would be used. However, the ability to run high resolution imaging logs was crucial to determining the potential of the offshore Sergipe fields, and these tools work best in water-based fluids. PETROBRAS selected a new high performance water-based fluid (WBF) to drill the Poco 3-GA-73-SES well. The fluid selection was based on the results of X-ray diffraction, dispersion/erosion and linear swell meter testing of Calumbi formation samples. The new WBF incorporates a unique polymer chemistry that can provide shale inhibition very similar to that achieved with an invert emulsion fluid, without sacrificing drilling performance. The polymeric additives can effectively flocculate and encapsulate colloidal drill solids so that they can be easily removed mechanically. The polymers also help prevent hole erosion and bit balling. After the high-performance WBF was used, the following results were obtained on the Poco 3- GA-73-SES well: 805 m drilled in 65 hr (12.65 m/hr) in a single bit run; trips completed with minimal use of the pumps or back reaming, considered exceptional for a WBF while drilling the Calumbi shale; imaging logs run successfully with no delays or obstructions while tripping or logging; the average hole diameter was 8.63-in. per the caliper log for the 8 1/2-in. section; no accretion on the bit or drill string observed; no flow line plugging or shaker screen blinding. (author)

33 CFR 96.370 - What are the requirements for vessels of countries not party to Chapter IX of SOLAS?

Science.gov (United States)

2010-07-01

... vessel, or self-propelled mobile offshore drilling unit of 500 gross tons or more, operated in U.S... Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY VESSEL OPERATING REGULATIONS RULES FOR THE SAFE OPERATION OF VESSELS AND SAFETY MANAGEMENT SYSTEMS How Will Safety Management Systems Be Certificated and...

46 CFR 58.60-9 - Industrial systems: Design.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Industrial systems: Design. 58.60-9 Section 58.60-9 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING MAIN AND AUXILIARY MACHINERY AND RELATED SYSTEMS Industrial Systems and Components on Mobile Offshore Drilling Units (MODU...

46 CFR 58.60-7 - Industrial systems: Piping.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Industrial systems: Piping. 58.60-7 Section 58.60-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING MAIN AND AUXILIARY MACHINERY AND RELATED SYSTEMS Industrial Systems and Components on Mobile Offshore Drilling Units (MODU...

46 CFR 58.60-5 - Industrial systems: Locations.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Industrial systems: Locations. 58.60-5 Section 58.60-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING MAIN AND AUXILIARY MACHINERY AND RELATED SYSTEMS Industrial Systems and Components on Mobile Offshore Drilling Units (MODU...

46 CFR 108.550 - Survival craft launching and recovery arrangements: General.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Survival craft launching and recovery arrangements...-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.550 Survival craft.... (c) Each survival craft must be arranged to clear each leg, column, footing, brace, mat, and each...

46 CFR 56.01-1 - Scope (replaces 100.1).

Science.gov (United States)

2010-10-01

... ships' and barges' piping systems and appurtenances. (b) The respective piping systems installed on ships and barges shall have the necessary pumps, valves, regulation valves, safety valves, relief valves... operation of the vessel. (c) Piping for industrial systems on mobile offshore drilling units need not fully...

Offshore Financial Centers in Global Capital Flow

Directory of Open Access Journals (Sweden)

Lutsyshyn Zoriana

2017-12-01

Full Text Available The article is dedicated to investigation of the place and role of offshore financial centers in financial globalization system, and of the reasons for using offshores in assets securitization mechanism. Numerous offshore and other preferential zones enabling to avoid the effective national and governmental tax regime are important attributes of global financial system and redistributive links of world financial flows. At present, around 70 countries and territories offer their offshore services for foreign capital, bank transactions, profitability from activities in financial markets proper. The global offshore business concentrates large amounts often having no relation to the country of origin, the so-called cosmopolitan capital (wandering. Although in the early 80's of the XXth century offshore companies were considered to control approximately 500 billion dollars, it was already in the early 90's that this amount doubled and was estimated as 1 trillion dollars. Today, from ⅓ to half of the world capital turnover goes through offshore business channels, and therefore, almost half of non-resident bank deposits are concentrated in world offshore centers. These are the world financial centers comprising international capital markets that provide for the accumulation and redistribution of world capital. From the process of reproduction (circulation of capital, the world financial centers plunge out the most homogeneous and mobile element — money, and freely manipulating with them, concentrate huge economic power in their hands. The role of world financial centers was also enhanced by the latest achievements in computer science, allowing execution of instant transactions and movement of huge amounts to any point of the world within the shortest possible time. The world financial centers consist not only of powerful banks and financial institutions operating on the international scene, but also have currency, stock and other exchanges as their

46 CFR 108.601 - Crane design.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Crane design. 108.601 Section 108.601 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Cranes Cranes § 108.601 Crane design. (a) Each crane and crane foundation on a unit must be designed in...

46 CFR 108.520 - Type of survival craft.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Type of survival craft. 108.520 Section 108.520 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.520 Type of survival craft. (a) Each lifeboat must be a fire-protected...

Importance of drill string assembly swivel in horizontal drilling

Directory of Open Access Journals (Sweden)

Edmund Tasak

2006-10-01

Full Text Available A part of the drill string – the swivel (rotational connector – accomplishes an important task in the horizontal drilling. Its malfunctioning makes it impossible to draw in ( install large diameter and length pipelines. The causes of the connector break-down during the horizontal drilling are investigated in the paper. The drilling has been made for twenty inches gas pipeline installation during reaming operations. A trouble was encountered making good work conditions of a system consisting of the drilling machine drill string reamer swivel tube shield of Cardan joint and the gas pipeline 500 m long. In this case, the swivel brokes down and the planned operation was not finished. The assessment of improper drilling conditions, selection of operation system components, and drilling parameters and the insufficient technological supervising have created an excessive risk of failure. A proper application of technical analysis would considerably decrease the hazard of failure which cause large costs, delays and decrease of confidence to the drilling contractor and pipeline installation.

Optimum fluid design for drilling and cementing a well drilled with coil tubing technology

Energy Technology Data Exchange (ETDEWEB)

Swendsen, O.; Saasen, A.; Vassoy, B. [Statoil (Norway); Skogen, E.; Mackin, F.; Normann, S. H.

1998-12-31

The strategy, design and drilling fluid and cementing operations in the first two wells drilled with coil tubing technology in the Gullfaks field in the Tampen Spur Area of the Norwegian sector of the North Sea are discussed. The drilling fluid use was a solids-free potassium formate/polymer brine-based fluid with a density of 1,50-1.56 g/cc, with flow properties characterized by very low fluid loss due to high extensional viscosity, a low viscosity at all shear rates, and a low degree of shear-thinning. The low viscous drilling fluid is considered to have been the major contributing factor in achieving excellent hole cleaning, no differential sticking, successful setting of cement kick-off plugs, problem-free running of the liner, and excellent zonal isolation when cementing the liner. These experiences led the authors to conclude that it is possible to formulate a brine-based solids-free drilling fluid with low viscosity and fluid loss properties for most formation pressure regimes, and that such a drilling fluid is well suited to drilling highly deviated slim hole wells where hole cleaning and differential sticking present special challenges. 12 refs., 2 tabs., 3 figs.

Offshoring Process

DEFF Research Database (Denmark)

Slepniov, Dmitrij; Sørensen, Brian Vejrum; Katayama, Hiroshi

2011-01-01

The purpose of this chapter is to contribute to the knowledge on how production offshoring and international operations management vary across cultural contexts. The chapter attempts to shed light on how companies approach the process of offshoring in different cultural contexts. In order...... of globalisation. Yet there are clear differences in how offshoring is conducted in Denmark and Japan. The main differences are outlined in a framework and explained employing cultural variables. The findings lead to a number of propositions suggesting that the process of offshoring is not simply a uniform...... technical-rational calculation of the most efficient organisation of activities across national borders, but it is rather specific to the parent companies’ national contexts....

46 CFR 108.221 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Storm rails. 108.221 Section 108.221 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Construction and Arrangement Rails § 108.221 Storm rails. Each unit must have a storm rail in the following...

Drilling bits for deep drilling and process for their manufacture

Energy Technology Data Exchange (ETDEWEB)

Rhode, H.; Juergens, R.; Feenstra, R.; Busking, B.E.

1978-11-30

The invention concerns a drilling head or a drilling bit for use in deep drilling in underground formations and particularly concerns a drilling bit with a drilling bit body, which has a shank and a hollow space, which is connected with a duct extending through the shank. The drilling bit body has several separate cutting elements for removing material from the floor of a borehole and hydraulic devices for cooling and/or cleaning the cutting elements are provided.

Occupational health offshore

Energy Technology Data Exchange (ETDEWEB)

Crosbie, A.; Davies, F.

2002-07-01

The proceedings contain the 29 papers presented at the conference plus the opening address from the chair of the Health and Safety Commission. The papers in the first session were concerned with policy, strategy and leadership and included a perspective from the offshore industry advisory committee, details of a health planning tool for occupational health assurance and lessons from occupational health management in the offshore sector. The two sessions on the second day dealt with occupational health in the offshore design process and case studies involving physical, chemical and biological agents. Topics included the need to consider occupational health when designing offshore installations, the development of a human factors engineering strategy in petrochemical engineering projects, measuring occupational exposure to hazardous chemicals, implementation of the noise at work regulations, hand arm vibration syndrome and issues with potable water maintenance. The two sessions on the third day were concerned with human factors and psychological health, and well-being and fitness for duty. Topics covered included circadian adaption to shift change in offshore shift workers, managing stress in the offshore environment, the role of employee assistance programmes in organisational stress management, health care and first aid (the revised ACOP), well-being at work, the medical and physical fitness of offshore emergency response rescue team members, the impact of health surveillance and promotion of offshore accident rates, and the implication of safety and heath of the aging of the workforce ion the Norwegian offshore industry.

Environmental education program for offshore employees; Projeto de educacao ambiental para empregados offshore

Energy Technology Data Exchange (ETDEWEB)

Santos, Antonio Carlos Pedrosa dos [PETROBRAS, Rio de Janeiro, RJ (Brazil). Unidade de Sistema de Sondagem Semi-Submersivel. Seguranca, Meio Ambiente e Saude; Osborne, Renata

2004-07-01

The Pedagogical Project of Environmental Education for Offshore Employees was developed in order to foster greater awareness of the environmental question and contribute towards the reduction of accidents. Main clients are contracted staff. This Project is carried out aboard marine units and consists of five modules with on- the-job classes (the option that it be conducted at the work site was the alternative chosen by the majority of participating employees). Subjects cover technical, historical and cultural matters connected with the environment and involve legislation, residues, energy, health and safety. In order to evaluate the course's receptivity and degree of understanding, a trial group was formed. During 2003, classes were conducted in 27 marine drilling units, 23 of which under contract. Total number of persons attending was 2.471, total number of class-hours being 246. After the course's conclusion, its strengths and weaknesses are evaluated in order to supply data for future improvements. In this way, subjects are always kept up to date and interest is maintained. (author)

Development of vertical drilling apparatus (Terra-Drill); Entwicklung eines Vertikal-Bohrgeraets (Terra-Drill) - Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Jenne, D.

2009-05-15

This well-illustrated final report for the Swiss Federal Office of Energy (SFOE) reports on the development of a vertical drilling apparatus named Terra-Drill. The various stages of the development of the apparatus, which is based on earlier designs, is discussed. New norms issued in Germany for the size of boreholes for buried vertical heat-exchangers and the appropriate linings to be used are discussed. The new Terra Drill 4407 V drilling apparatus and its testing are discussed. The drill is quoted as being particularly suitable for cramped locations. Technical details are presented and a comprehensive collection of photographs is included. Various preliminary reports and development documentation are included.

Rapid Access Ice Drill: A New Tool for Exploration of the Deep Antarctic Ice Sheets and Subglacial Geology

Science.gov (United States)

Goodge, J. W.; Severinghaus, J. P.

2014-12-01

The Rapid Access Ice Drill (RAID) will penetrate the Antarctic ice sheets in order to core through deep ice, the glacial bed, and into bedrock below. This new technology will provide a critical first look at the interface between major ice caps and their subglacial geology. Currently in construction, RAID is a mobile drilling system capable of making several long boreholes in a single field season in Antarctica. RAID is interdisciplinary and will allow access to polar paleoclimate records in ice >1 Ma, direct observation at the base of the ice sheets, and recovery of rock cores from the ice-covered East Antarctic craton. RAID uses a diamond rock-coring system as in mineral exploration. Threaded drill-pipe with hardened metal bits will cut through ice using reverse circulation of Estisol for pressure-compensation, maintenance of temperature, and removal of ice cuttings. Near the bottom of the ice sheet, a wireline bottom-hole assembly will enable diamond coring of ice, the glacial bed, and bedrock below. Once complete, boreholes will be kept open with fluid, capped, and made available for future down-hole measurement of thermal gradient, heat flow, ice chronology, and ice deformation. RAID will also sample for extremophile microorganisms. RAID is designed to penetrate up to 3,300 meters of ice and take sample cores in less than 200 hours. This rapid performance will allow completion of a borehole in about 10 days before moving to the next drilling site. RAID is unique because it can provide fast borehole access through thick ice; take short ice cores for paleoclimate study; sample the glacial bed to determine ice-flow conditions; take cores of subglacial bedrock for age dating and crustal history; and create boreholes for use as an observatory in the ice sheets. Together, the rapid drilling capability and mobility of the drilling system, along with ice-penetrating imaging methods, will provide a unique 3D picture of the interior Antarctic ice sheets.

Drilling comparison in "warm ice" and drill design comparison

DEFF Research Database (Denmark)

Augustin, L.; Motoyama, H.; Wilhelms, F.

2007-01-01

For the deep ice-core drilling community, the 2005/06 Antarctic season was an exciting and fruitful one. In three different Antarctic locations, Dome Fuji, EPICA DML and Vostok, deep drillings approached bedrock (the ice-water interface in the case of Vostok), emulating what had previously been...... achieved at NorthGRIP, Greenland, (summer 2003 and 2004) and at EPICA Dome C2, Antarctica (season 2004/05). For the first time in ice-core drilling history, three different types of drill (KEMS, JARE and EPICA) simultaneously reached the depth of 'warm ice' under high pressure. After excellent progress...... at each site, the drilling rate dropped and the drilling teams had to deal with refrozen ice on cutters and drill heads. Drills have different limits and perform differently. In this comparative study, we examine depth, pressure, temperature, pump flow and cutting speed. Finally, we compare a few...

Offshore Investment Funds

Directory of Open Access Journals (Sweden)

Shang-Jin Wei

1999-12-01

Full Text Available Offshore investment funds are alleged to have engaged in trading behavior that is different from their onshore counterparts because they may be subject to less supervision and regulation. In particular, they may trade more intensely. They could also pursue more aggressively certain trading strategies such as positive feedback trading or herding that could contribute to a greater volatility in the market. Using a unique data set, this chapter compares the trading behavior in the Korean stock market between offshore investment funds with their onshore counterparts registered in the US and UK. There are a number of interesting findings. First, there is indeed evidence suggesting that the offshore funds trade more intensely than their onshore counterparts. Second, however, there is no evidence that the offshore funds engage in positive feedback trading. In contrast, there is strong evidence that the funds from the U.S. and U.K. do. Third, while offshore funds do herd, they do so far less than onshore funds in the U.S. or UK. Fourth, offshore funds hold less glamour stocks (e.g. stocks with high P/E in their portfolio than funds in the U.S. or U.K. do. Moreover, flight to glamour stocks during the in-crisis period is less evident in the case of offshore funds. In sum, offshore funds are no especially worrisome monsters.

Potential for offshore geothermal developments using deep gas wells

Energy Technology Data Exchange (ETDEWEB)

Teodoriu, C.; Falcone, G. [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). ITE

2013-08-01

The development of geothermal resources is steadily increasing as operators meet the challenge of maximising the temperature difference between production and injection wells, while minimising the wellhead temperature of the latter. At present, the minimum working wellhead temperature reported for the heat-to-electricity conversion cycles is limited to about 80 C. The cycle efficiency can be improved by reducing the injection temperature, which is the temperature at which the fluid exits the process. This paper evaluates the potential for generating electricity with a subsea geothermal plant using the difference between downhole reservoir temperature and that of the cold seawater at the mud line. The temperature in the world's oceans is relatively constant, ranging from 0 to 4 C at around 400 meters water depth. The use of these lower offshore water temperatures may help boost geothermal energy development. Deep gas resources are considered to be held within reservoirs below 4600 meters (15000 feet) and are relatively undeveloped as the risks and costs involved in drilling and producing such resources are extremely high. These deep resources have high reservoir temperatures, which offer an opportunity for geothermal exploitation if a new development concept can be formulated. In particular, the well design and reservoir development plan should consider reutilising existing well stock, including dry and plugged and abandoned wells for geothermal application once the gas field has been depleted. The major risks considered in this study include alternative uses of wells in no flow or rapid depletion situations. Reutilisation of the wells of depleted gas reservoirs will invariably lead to lower geothermal development costs compared with starting a geothermal campaign by drilling new wells. In particular, the well design and reservoir development plan should consider reutilising existing well stock, including dry and plugged and abandoned wells for geothermal

JOINT-INDUSTRY PARTNERSHIP TO DEVELOP A HOLLOW SPHERE DUAL-GRADIENT DRILLING SYSTEM

Energy Technology Data Exchange (ETDEWEB)

William C. Maurer; Colin Ruan; Greg Deskins

2003-05-01

result, an excessive amount of this polymer mud flowed across the screen with the beads instead of through the screen. At the completion of the Phase I project, it was concluded that the hollow sphere system would not work effectively with the polymer mud tested. ExxonMobil and Shell engineers proposed that additional sphere separation tests needed to be conducted with weighted oilfield waterbase and oilbase muds to determine if the DGD system would work with these muds. The DOE agreed to provide a $200,000 grant for these tests. The DOE-funded tests, described in this report, showed that the spheres could be pumped with conventional oilfield centrifugal and triplex mud pumps and separated effectively from both oilfield waterbase and oilbase muds using conventional oilfield shale shakers and hydrocyclones. As a result of the success of these DOE tests, this DGD system is ready for full-scale field testing, first on land wells and later in the offshore environment. Maurer Technology Inc. is currently proposing a Phase II project to oil companies to further develop this DGD concept. This project would be funded by four to eight operators. If Phase II tests are successful, Noble plans to commercialize this system with a service company partner that will market and operate the DGD system on Noble's and other drilling contractors' rigs.

46 CFR 108.707 - First aid kit.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false First aid kit. 108.707 Section 108.707 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Miscellaneous Equipment § 108.707 First aid kit. Each unit must have a first-aid kit approved by the Mine Safety...

The effects of meshed offshore grids on offshore wind investment – a real options analysis

DEFF Research Database (Denmark)

Schröder, Sascha Thorsten; Kitzing, Lena

2012-01-01

Offshore wind farms in future meshed offshore grids could be subject to different regulatory regimes. Feed-in tariffs would absorb market risk from wind farm operators, whereas price premium mechanisms leave operators exposed to market price signals. In this case, it plays a decisive role which...... price applies to a node in an offshore grid. The offshore node will either be integrated into any of the neighbouring markets, with access to the respective maximum price, or be subject to separate nodal pricing. We investigate the different regulatory regimes for connections to one to four countries...... based on a stochastic model capturing uncertainties in prices and line failures. The stochastic analysis shows that in case the wind park is granted access to the respective maximum price, there is a significant option value connected to the operational flexibility of accessing several markets: The wind...

The effects of meshed offshore grids on offshore wind investment – a real options analysis

DEFF Research Database (Denmark)

Schröder, Sascha Thorsten; Kitzing, Lena

2012-01-01

based on a stochastic model capturing uncertainties in prices and line failures. The stochastic analysis shows that in case the wind park is granted access to the respective maximum price, there is a significant option value connected to the operational flexibility of accessing several markets: The wind......Offshore wind farms in future meshed offshore grids could be subject to different regulatory regimes. Feed-in tariffs would absorb market risk from wind farm operators, whereas price premium mechanisms leave operators exposed to market price signals. In this case, it plays a decisive role which...... price applies to a node in an offshore grid. The offshore node will either be integrated into any of the neighbouring markets, with access to the respective maximum price, or be subject to separate nodal pricing. We investigate the different regulatory regimes for connections to one to four countries...

Whether and What to Offshore?

DEFF Research Database (Denmark)

Jensen, Peter Ørberg; Pedersen, Torben

In this article, we explore the idea that offshoring of services and technical work should be regarded as a dynamic process that evolves over time. Firms gradually move from offshoring of simple, standardized activities towards offshoring of advanced activities when they accumulate experience...... with offshoring, and this type of offshoring comes with an entirely different set of characteristics compared to traditional, cost-seeking offshoring. Based on a unique survey among the total population of firms in the eastern region of Denmark, we analyze some of the dynamics of this process through a model...... that incorporates two different aspects of the process of offshoring. First, we approach the question of whether to offshore and establish a baseline that investigates the determinants of firms’ participation—or lack thereof—in offshoring. Secondly, we approach the question of what to offshore and the subsequent...

78 FR 27913 - Revision of Crane Regulation Standards for Mobile Offshore Drilling Units (MODUs), Offshore...

Science.gov (United States)

2013-05-13

...)(1) by updating the reference for API nameplate data to reflect its location in the latest edition of.... Civil Justice Reform I. Protection of Children J. Indian Tribal Governments K. Energy Effects L... existing regulations by adopting the most recent editions of API Spec. 2C and RP 2D standards. By updating...

How we improved operations in drilling pre-salt wells

Energy Technology Data Exchange (ETDEWEB)

Hougaz, Augusto Borella [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil); Martins, Luiz Felipe; Bittencourt, Jessica Lima; Braz, Luciano Machado [Genesis do Brasil, Sao Paulo, SP (Brazil); Damski, Carlos [Genesis Petroleum Technology Pty Ltd. (GPT), Bentley, WA (Australia)

2012-07-01

The development of pre-salt wells offshore Brazil has been one of the most challenging projects in history of E and P. Facing water depths of 2000+ meters, a salt layer 2000 meters thick to reach reservoirs at 7000 meters below sea level, has to use technological and procedural techniques never used before. In those 2 years of exploration of those fields many technologies were tested and improved. This paper describes the systematic approach was taken to analyze, plan and follow-up the development of drilling operations campaign in those fields, and the case study of overall process improvement. The assumption was to apply a risk analysis tool which uses previous data to analyze the performance and plan future time. The goals of this process are continuous improvement of execution and process control for each operation. Looking into previous performance, new interventions were planned more accurately and further improvements were studied. The frequent follow up of the drilling intervention was done using the statistical base to compare the most recent results. At operational level it was possible to see if the last operation was done in the 1st, 2nd, 3rd or 4th quartile of its related statistical distribution, as well as to verify the difference within P10 and P90, which indicates the control of each operation execution process. The same process was done for some rig related operations and for the whole intervention at end of it. Close contact with the intervention progress was kept and actions taken in any major deviation from the plan. This paper describes the case study where the process control and optimization of the total time for drilling 10 wells with similar design was measured between March 2009 and May 2011. It resulted in significant improvement in the drilling process. (author)

Heat generated by dental implant drills during osteotomy-a review: heat generated by dental implant drills.

Science.gov (United States)

Mishra, Sunil Kumar; Chowdhary, Ramesh

2014-06-01

Osseointegration is the more stable situation and results in a high success rate of dental implants. Heat generation during rotary cutting is one of the important factors influencing the development of osseointegration. To assess the various factors related to implant drills responsible for heat generation during osteotomy. To identify suitable literature, an electronic search was performed using Medline and Pubmed database. Articles published in between 1960 to February 2013 were searched. The search is focused on heat generated by dental implant drills during osteotomy. Various factors related to implant drill such effect of number of blades; drill design, drill fatigue, drill speed and force applied during osteotomies which were responsible for heat generation were reviewed. Titles and abstracts were screened, and literature that fulfilled the inclusion criteria was selected for a full-text reading. The initial literature search resulted in 299 articles out of which only 70 articles fulfils the inclusion criteria and were included in this systematic review. Many factors related to implant drill responsible for heat generation were found. Successful preparation of an implant cavity with minimal damage to the surrounding bone depends on the avoidance of excessive temperature generation during surgical drilling. The relationship between heat generated and implant drilling osteotomy is multifactorial in nature and its complexity has not been fully studied. Lack of scientific knowledge regarding this issue still exists. Further studies should be conducted to determine the various factors which generate less heat while osteotomy such as ideal ratio of force and speed in vivo, exact time to replace a drill, ideal drill design, irrigation system, drill-bone contact area.

Dictionary of drilling, production and offshore operations. English-German and German-English. Woerterbuch der Bohr-, Foerder- und Offshore-Technik. Englisch-Deutsch und Deutsch-Englisch

Energy Technology Data Exchange (ETDEWEB)

Rathjen, H R; Schaumberg, G; Sickinger, W; Trentmann, A F [comps.

1985-01-01

This dictionary is to give users in the petroleum and natural gas industry, the offshore industry, the service industries, authorities, schools, and other interested readers access to the English-language terminology in this field. An alphabetic list of abbreviations and acronyms frequently used in reports and in telex services is presented in the appendix, along with tables of British and US measures.

Advanced control strategies for a drill rig

International Nuclear Information System (INIS)

Banerjee, A.; Hiller, M.; Fink, B.

1996-01-01

The construction of tunnels is usually undertaken using a combination of blasting and drilling to achieve rock excavation. Easy handling and high accuracy, and thus greater efficiency, in drilling rigs is an essential ingredient of successful competition in the market place. This article describes a cartesian control concept used for a twin boom drill rig. This simplifies the handling of a drilling boom, reduces the duration of a working cycle and increases security. A remote control system has been added to the drill rig to support the operator working in complicated environments. (UK)

46 CFR 109.585 - Use of auto pilot.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Use of auto pilot. 109.585 Section 109.585 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Miscellaneous § 109.585 Use of auto pilot. Except as provided in 33 CFR 164.15, when the automatic pilot is used...

33 CFR 140.7 - Incorporation by reference.

Science.gov (United States)

2010-07-01

... Devices. 143.405 ANSI Z41-1983—American National Standard for Personal Protection-Protective Footwear. 142... Industrial Head Protection. 142.30 International Maritime Organization (IMO) IMO Sales, New York Nautical... Construction and Equipment of Mobile Offshore Drilling Units. 143.207; 146.205 [CGD 84-098b, 54 FR 21571, May...

The new logistic and waste management concept for Mittelplate drilling platform; Das neue Logistik- und Entsorgungskonzept der Bohr- und Foerderinsel Mittelplate

Energy Technology Data Exchange (ETDEWEB)

Kowalczyk, D. [RWE Dea AG, Hamburg (Germany); Wachtendorf, A. [M-I SWACO Deutschland GmbH, Celle (Germany)

2007-09-13

The installation of a new drilling system on Mittelplate platform (owned by RWE Dea AG as managing company and Wintershall AG in 50 percent shares) in late 2005 made it possible to implement a continuous drilling programme in deeper strata. A new logistic and waste management concept was developed and implemented in order to meet the new logistic requirements of this offshore installation in the national park ''Schleswig-Holsteinisches Wattenmeer'' while optimizing the successful Mittelplate HSE safety package. In the conception phase, commercial technologies in the fields of drilling cutting, transport, marine logistics, flushing and waste management were collected world-wide and were analyzed with a view to their applicability in this ecologically sensitive region. The optimum technical solution, which is also economically efficient, in accordance with the safety and environmental protection philosophy of the consortium, and also optimizes the supply and waste management process relating to drilling, comprises three interacting elements, i.e. a cutting transport system, a cutting logistic centre, and a flushing tank store. (orig.)

Vital signs: drilling rush accelerates, led by stellar B.C. natural gas discoveries

International Nuclear Information System (INIS)

Lunan, D.

2001-01-01

A recent survey of drilling activity in the Western Canadian Sedimentary Basin provide clear evidence of intensified efforts to match the aggressive forecast of 17,500 well completions in 2001, forecast by the Petroleum Services Association of Canada, or the 18,500 new wells forecast by the Canadian Association of Oilwell Drilling Contractors, and satisfy the expected strong natural gas demand. The rush for drilling properties boosted first-quarter land sale bonus payments by 78 per cent to more than $500 million, or about $356 per hectare from $282 million or $256 per hectare in the first three months of 2000. Land acquisition is most robust in northeastern British Columbia, where a series of 50-million-cubic feet-per-day discoveries in the Ladyfern region has ignited the hottest exploration play of this year, resulting in a 400 per cent increase in first quarter bonus payments to $212 million, or $613 per hectare. Overall Western Canada rig count peaked at 614 active units in late February, declining since to 264 rigs in April, due to the onset of spring breakup. Success rate in the first quarter of 2001 for exploratory drilling peaked at 72 per cent, up from 53 per cent a year ago. Industry-wide success rate jumped to 83 per cent from 75 per cent in 2000. Average depth in BC in the first quarter of 2001 reached 1,700 metres, the highest in Western Canada, compared to about 1,300 metres a year ago. Industry-wide, the average depth slipped from 1,143 metres to 1,134 metres, reflecting the continuing reliance on shallow gas drilling in an effort to attach known reserves as quickly as possible. Offshore drilling on East Coast provides a different picture: drilling depth averages climbed to 10,339 metres from 7,131 metres in 2000. Discovery of the Deep Panuke field by PanCanadian Petroleum is considered partly responsible for the sudden increase in well depth. tabs., 2 photos

HIGH-POWER TURBODRILL AND DRILL BIT FOR DRILLING WITH COILED TUBING

Energy Technology Data Exchange (ETDEWEB)

Robert Radtke; David Glowka; Man Mohan Rai; David Conroy; Tim Beaton; Rocky Seale; Joseph Hanna; Smith Neyrfor; Homer Robertson

2008-03-31

Commercial introduction of Microhole Technology to the gas and oil drilling industry requires an effective downhole drive mechanism which operates efficiently at relatively high RPM and low bit weight for delivering efficient power to the special high RPM drill bit for ensuring both high penetration rate and long bit life. This project entails developing and testing a more efficient 2-7/8 in. diameter Turbodrill and a novel 4-1/8 in. diameter drill bit for drilling with coiled tubing. The high-power Turbodrill were developed to deliver efficient power, and the more durable drill bit employed high-temperature cutters that can more effectively drill hard and abrasive rock. This project teams Schlumberger Smith Neyrfor and Smith Bits, and NASA AMES Research Center with Technology International, Inc (TII), to deliver a downhole, hydraulically-driven power unit, matched with a custom drill bit designed to drill 4-1/8 in. boreholes with a purpose-built coiled tubing rig. The U.S. Department of Energy National Energy Technology Laboratory has funded Technology International Inc. Houston, Texas to develop a higher power Turbodrill and drill bit for use in drilling with a coiled tubing unit. This project entails developing and testing an effective downhole drive mechanism and a novel drill bit for drilling 'microholes' with coiled tubing. The new higher power Turbodrill is shorter, delivers power more efficiently, operates at relatively high revolutions per minute, and requires low weight on bit. The more durable thermally stable diamond drill bit employs high-temperature TSP (thermally stable) diamond cutters that can more effectively drill hard and abrasive rock. Expectations are that widespread adoption of microhole technology could spawn a wave of 'infill development' drilling of wells spaced between existing wells, which could tap potentially billions of barrels of bypassed oil at shallow depths in mature producing areas. At the same time, microhole

Three Essays in the Public Economics of Offshore Hydrocarbon Investment and Production

Science.gov (United States)

Kearney, Owen P.

Offshore sources, in both shallow and deep waters, are increasingly important contributors to global oil and natural gas production. As both resource owner and taxing authority, national governments play an important role in the production of these offshore hydrocarbons. How the policy choices of these governments affect firm behavior, however, is not necessarily well understood. This dissertation contributes to our knowledge of how public policy influences offshore hydrocarbon investment and production. In the first essay, I estimate the investment responses of hydrocarbon producers to the suspension of the royalty, a type of production tax levied on production from federal lands. I find that the potential for a royalty payments waiver: (1) increases the probability that an individual tract is acquired by an average of 193% (a mean increase of 5.6 percentage points); (2) decreases the probability that a lease is ever drilled during its observed lease term by an average of 14.5% (a mean decrease of 1.3 percentage points); and (3) increases the expected number of explored leases by 150%. The introduction of DWRRA also increases the average winning bid per lease by 60%. These estimates quantify the magnitudes of the discouraging effects of production taxation on oil and natural gas investment. In the second essay, I quantify the implied value of information spillovers in oil and natural gas exploration using an event study design. I find that 25 trading days after a discovery, firms that own leases adjacent to the discovery lease (but not the discovery lease, itself) realize an average abnormal return translating to 315 million in market capitalization. This effect is quantitatively large compared to costs for drilling an exploratory well. In the final essay, I measure how oil price affects water injection, a method for prolonging the productive lifetime of oil fields. I find that a 1 rise in price increases the water injected into the well's reservoir by

Demonstrations of Gravity-Independent Mobility and Drilling on Natural Rock using Microspines

Science.gov (United States)

Parness, Aaron; Frost, Matthew; King, Jonathan P.; Thatte, Nitish

2012-01-01

The video presents microspine-based anchors be ing developed for gripping rocks on the surfaces of comets and asteroids, or for use on cliff faces and lava tubes on Mars. Two types of anchor prototypes are shown on supporting forces in all directions away from the rock; >160 N tangent, >150 N at 45?, and >180 N normal to the surface of the rock. A compliant robotic ankle with two active degrees of freedom interfaces these anchors to the Lemur IIB robot for future climbing trials. Finally, a rotary percussive drill is shown coring into rock regardless of gravitational orientation. As a harder- than-zero-g proof of concept, inverted drilling was performed creating 20mm diameter boreholes 83 mm deep in vesicular basalt samples while retaining 12 mm diameter rock cores in 3-6 pieces.

A fair wind for the offshore

International Nuclear Information System (INIS)

Houot, G.

2009-01-01

The wind power future will take into account the sea. But to increase, the offshore channel must manage its organization and create a real cross-border cooperation. The author presents an economic analysis of the market with a special attention to the french sector. A map of the offshore sites in Europe is provided. (A.L.B.)

Effects of drilling cuttings on the behavior of the Norway lobster Nephrops norvegicus

Energy Technology Data Exchange (ETDEWEB)

Richardson, C A

1984-05-01

Small quantities of drilling cuttings (100 g/250 cm/sup 2/) were found to affect both the survival and general behavior of Nephrops norvegicus held in experimental aquaria. In one experiment volatile hydrocarbons released from the cuttings caused a significant decrease in the heat of the exopodite on the third maxilliped. Flicking rates of the antennule and the time taken to identify and capture food introduced into the tanks were unaffected by exposure to cuttings. When the water flow through the tanks was interrupted for 12 h, 58% of animals died after exposure to the highest concentration of cuttings but those at the lower concentrations survived. After the water flow was restored the remaining survivors showed disorientated behavior and uncoordinated movements which lasted for about 36 h. In this condition animals will be more vulnerable to predators. This unnatural behavior may have serious implications for natural populations exposed to cuttings discharge in the close vicinity of offshore drilling platforms. 11 references, 3 tables.

Identifying and evaluating high risk areas and challenges on marine drilling riser system in relation to deepwater problems

OpenAIRE

Iversen, Alexander

2012-01-01

Master's thesis in Offshore technology The main concerns during drilling operations are riser integrity and maintaining well control. This thesis has mainly been focusing on the problems and challenges faced with the marine riser system to illuminate high risk areas related to riser integrity. A marine riser system consists generally of four main elements; the upper marine riser package, riser joints, lower marine riser package, and the blowout preventer, each playing an important par...

Relevance of East African Drill Cores to Human Evolution: the Case of the Olorgesailie Drilling Project

Science.gov (United States)

Potts, R.

2016-12-01

Drill cores reaching the local basement of the East African Rift were obtained in 2012 south of the Olorgesailie Basin, Kenya, 20 km from excavations that document key benchmarks in the origin of Homo sapiens. Sediments totaling 216 m were obtained from two drilling locations representing the past 1 million years. The cores were acquired to build a detailed environmental record spatially associated with the transition from Acheulean to Middle Stone Age technology and extensive turnover in mammalian species. The project seeks precise tests of how climate dynamics and tectonic events were linked with these transitions. Core lithology (A.K. Behrensmeyer), geochronology (A. Deino), diatoms (R.B. Owen), phytoliths (R. Kinyanjui), geochemistry (N. Rabideaux, D. Deocampo), among other indicators, show evidence of strong environmental variability in agreement with predicted high-eccentricity modulation of climate during the evolutionary transitions. Increase in hominin mobility, elaboration of symbolic behavior, and concurrent turnover in mammalian species indicating heightened adaptability to unpredictable ecosystems, point to a direct link between the evolutionary transitions and the landscape dynamics reflected in the Olorgesailie drill cores. For paleoanthropologists and Earth scientists, any link between evolutionary transitions and environmental dynamics requires robust evolutionary datasets pertinent to how selection, extinction, population divergence, and other evolutionary processes were impacted by the dynamics uncovered in drill core studies. Fossil and archeological data offer a rich source of data and of robust environment-evolution explanations that must be integrated into efforts by Earth scientists who seek to examine high-resolution climate records of human evolution. Paleoanthropological examples will illustrate the opportunities that exist for connecting evolutionary benchmarks to the data obtained from drilled African muds. Project members: R. Potts, A

Vadose zone drilling at the NTS

International Nuclear Information System (INIS)

Efurd, D.W.

1994-01-01

The Yucca Mountain Project has an opportunity to evaluate possible mobilization and transport of radioactive materials away from the storage horizon in the proposed repository. One scenario by which such transport could occur involves water leaving the storage area and carrying radioactive particulates of colloidal size. The colloids could move along the gas-liquid interface in partially filled fractures within the vadose zone. It should be possible to check the reality of this proposed scenario by examining ''anthropogenic analogs'' of the repository. These are sites of nuclear tests conducted in unsaturated tuff at the Nevada Test Site (NTS). We propose to drill under one or more such sites to determine if radionuclides have moved from their original confinement in the puddle- glass at the bottom of the cavity. This document examines the characteristics of an ideal test site for such a study, suggests several possible locations that have some of the desired characteristics, and recommends one of these sites for the proposed drilling

Safety in offshore engineering an academic course covering safety in offshore wind

NARCIS (Netherlands)

Cerda Salzmann, D.J.

2011-01-01

Offshore projects are known for their challenging conditions, generally leading to high risks. Therefore no offshore project can go without a continuous and extensive assessment on safety issues. The Delft University of Technology is currently developing a course "Safety in Offshore Engineering"

Governance of Arctic Offshore Oil & Gas Activities: Multilevel Governance & Legal Pluralism at Stake

DEFF Research Database (Denmark)

Pelaudeix, Cecile

2015-01-01

This article analyses the governance process of offshore oil and gas activities in the Arctic with the concept of multilevelgovernance and legal pluralism to address both issues of management of the environment and public participation. The analysis goes beyond the single issue of fragmentation p...... and from regional government, indigenous shareholders and corporation perspectives, could be helpful in providing relevant actors with arguments to weigh the decision on seismic and drilling activities in relation to risk acceptance.......This article analyses the governance process of offshore oil and gas activities in the Arctic with the concept of multilevelgovernance and legal pluralism to address both issues of management of the environment and public participation. The analysis goes beyond the single issue of fragmentation...... pertaining to the international and supranational levels, to encompass national and regional levels and evaluate how the interactions between those levels structure the policy process and impact the efficiency of environmental management and public participation. Four paths of reflection arise from...

CASING DRILLING TECHNOLOGY

Directory of Open Access Journals (Sweden)

Nediljka Gaurina-Međimurec

2005-12-01

Full Text Available Casing drilling is an alternative option to conventional drilling and uses standard oilfield casing instead of drillstring. This technology is one of the greatest developments in drilling operations. Casing drilling involves drilling and casing a well simultaneously. In casing driling process, downhole tools can be retrieved, through the casing on wire-line, meaning tool recovery or replacement of tools can take minutes versus hours under conventional methods. This process employs wireline-retrievable tools and a drill-lock assembly, permitting bit and BHA changes, coring, electrical logging and even directional or horizontal drilling. Once the casing point is reached, the casing is cemented in place without tripping pipe.

Application of Formation Testing While Drilling (GeoTap) for acquiring formation pressure data from the Azeri, Chirag and Guneshli wells which were drilled in the Khazarian-Caspian Sea of the Azerbaijan Republic

Science.gov (United States)

Amirov, Elnur

2016-04-01

A new technology to acquire wireline quality pressure tests using a Logging While Drilling approach has been successfully implemented few years ago in Azeri, Chirag and Guneshli wells which were drilled in the Khazarian-Caspian Sea of the Azerbaijan Republic. The Formation Tester While Drilling tool (GeoTap) uses a testing sequence similar to wireline tools. A single probe is extended to the borehole wall and a small pretest volume withdrawn from the formation. The resulting pressure transient is then analyzed for formation pressure, formation permeability and mobility information. Up-link and down-link capabilities have been added to achieve test control and quality feedback. An efficient downlink algorithm is used downhole to analyze the data. The parameters and pressure data are transmitted to the surface in real-time for continuous monitoring of the test. More detailed pressure data is recorded and retrieved after returning to surface. Use of a quartz gauge allows excellent accuracy. Azeri, Chirag and Guneshli fields consist of layered sand reservoirs alternation with shale sequences and detailed pressure data is acquired on a high percentage of wells in order to understand lateral and vertical continuity of different flow units. The formation tester can be utilized with the 'triple combo' Logging While Drilling string which eliminates the need to rig up wireline on many wells. Wireline formation tester runs are time consuming - particularly if high deviation or high overbalance conditions are encountered requiring pipe conveyed techniques. Non-Productive Time is high when the wireline tools are stuck and fishing operations are required. The Sperry Drilling GeoTap formation pressure tester service provides real-time formation pressure measurements. It bridges the critical gap between drilling safety and optimization, by providing early and reliable measurements of key reservoir properties, while improving reservoir understanding and completion design in real

Drilling unit

Energy Technology Data Exchange (ETDEWEB)

Umanchik, N P; Demin, A V; Khrustalev, N N; Linnik, G N; Lovchev, S V; Rozin, M M; Sidorov, R V; Sokolov, S I; Tsaregradskiy, Yu P

1981-01-01

A drilling unit is proposed which includes a hydraulic lifter, hydraulic multiple-cylinder pump with valve distribution and sectional drilling pump with separators of the working and flushing fluid. In order to reduce metal consumption and the overall dimensions of the drilling unit, the working cavity of each cylinder of the hydraulic multiple-cylinder pump is equipped with suction and injection valves and is hydraulically connected to the working cavity by one of the sections of the drilling pump.

China: an emerging offshore wind development hotspot. With a new assessment of China's offshore wind potential

Energy Technology Data Exchange (ETDEWEB)

Reinvang, Rasmus; Enslow, Rachel; Beaumont, Hubert

2010-08-15

This study provides new and more detailed estimates of the offshore wind energy resources in China, with particular focus on Southern China. The study points out that the offshore wind industry is ramping up in China with at least 11.9GW in the development pipeline per April 2010. The study estimates the offshore wind potential of China (excluding Taiwan) to 11,580TWh/year. The study proves estimates and wind energy resource maps per province. Fujian, Zhejiang and Hainan stand out with the highest offshore wind speeds in China while Guangdong also shows significant potential, with annual wind speed averages of 6.5-10.2m/s and an energy density range of 12-36GWh/km2. Even though current offshore wind development is mainly taking place in Fujian and Jiangsu, this study shows that the potential is likely even greater in other provinces. The study was developed by the Chinese Wind Energy Association (CWEA) and Sun Yat-sen University, and commissioned by WWF as part of a project funded by the Norwegian Agency of development Coopeartion (Norad). Methodology and constraints: The wind resource analysis improves upon previous studies in estimating the wind energy generation potential for offshore wind power in China, with available meteorological data adjusted for influence of typhoons. The study models how much energy offshore wind can produce along China's coast up to 100km from the shore by calculating the energy output of theoretical wind farms by applying the power curve of a 3MW turbine at a 100m hub height. In addition the study further expands by giving special consideration to the deep-sea offshore potential at +50m water depths. The study focuses particularly on the coastline from Shandong down to Hainan. The final results provide good indication of the offshore wind resource in China when comparing one area to the other. The report can therefore be used as a preliminary tool to identifying most interesting provinces and locations for offshore wind

Scientific Drilling in the Arctic Ocean: A challenge for the next decades

Science.gov (United States)

Stein, R.; Coakley, B.

2009-04-01

Nansen Arctic Drilling Program as well as by sponsorships from British Petroleum, ConocoPhillips, ExxonMobil, Norwegian Petroleum Directorate, StatoilHydro, and Shell International. The major targets of the workshop were: (1) to bring together an international group of Arctic scientists, young scientists and ocean drilling scientists to learn and exchange ideas, experience and enthusiasm about the Arctic Ocean; (2) to develop a scientific drilling strategy to investigate the tectonic and paleoceanographic history of the Arctic Ocean and its role in influencing the global climate system; (3) to summarize the technical needs, opportunities, and limitations of drilling in the Arctic; (4) to define scientific and drilling targets for specific IODP-type campaigns in Arctic Ocean key areas to be finalized in the development of drilling proposals. Following overview presentations about the history of the Arctic Ocean, legacy of high-latitude ocean drilling, existing site-survey database, technical needs for high-latitude drilling, possibilities of collaboration with industry, and the process of developing ocean-drilling legs through IODP, the main part of the workshop was spent in thematic and regional break-out groups discussing the particular questions to be addressed by drilling and the particular targets for Arctic scientific drilling. Within the working groups, key scientific questions (related to the overall themes paleoceanography, tectonic evolution, petrology/geochemistry of basement, and gas hydrates) and strategies for reaching the overall goals were discussed and - as one of the main results - core groups for further developing drilling proposals were formed. Based on discussions at this workshop, approximately ten new pre-proposals are planned to be submitted to IODP for the April 01- 2009 deadline. We hope that the development of new scientific objectives through the pre-proposal process will help reshape plans for scientific ocean drilling beyond 2013 and direct

Viewing engineering offshoring in a network perspective

DEFF Research Database (Denmark)

Hansen, Zaza Nadja Lee; Zhang, Yufeng; Ahmed-Kristensen, Saeema

2013-01-01

of how to effectively manage engineering offshoring activities in a context of global engineering networks. The main research question, therefore, is: “Can offshoring of engineering tasks be explained and managed using the concept of Global Engineering Networks (GEN)?” Effective approaches to handling...... of large multinational corporations in Denmark were carried out. Data gathering was mainly documentary studies and interviews. The main data analysis approaches were coding (Strauss and Corbin) and pattern-matching (Yin). The dataset was analysed using the GEN framework suggested by Zhang et al. and Zhang...... by extending the GEN framework to address complications within engineering offshoring. This strengthens both academic fields, and will be able to help engineering managers to develop appropriate engineering network configurations for offshore engineering operations....

From Offshoring to Backshoring

DEFF Research Database (Denmark)

Slepniov, Dmitrij; Madsen, Erik Skov

2015-01-01

The purpose of this paper is to examine the evolution of offshoring over time. The paper employs qualitative methodology and on the basis of two case studies of Danish companies, it develops a framework conceptualizing the stages of offshoring and highlights the factors driving the transition...... between these stages. The framework challenges the linear nature of offshoring and proposes the existence of ‘the pendulum effect’. The pendulum effect suggests that the modes of offshoring (i.e. captive and non-captive) and geographies of offshoring (i.e. home and abroad) are not static; rather...

Industrial opportunities - offshore

International Nuclear Information System (INIS)

Gerrits, D.J.

1998-01-01

Industrial opportunities available in the Canadian offshore petroleum industry are discussed. Oil has been produced offshore from Nova Scotia since 1992, and offshore from Newfoundland since 1997. Special needs that must be addressed in offshore operations in eastern Canada such as the cold North Atlantic environment, isolation, logistics, safety, and quality assurance, are examined. The most obvious opportunities lie with the designing, building and installing the facilities needed to extract oil and gas from beneath the sea floor and transport it to market. However, there are also opportunities in designing and fabricating clothing, customized food containers and other equipment for offshore needs. Short term opportunities also exist in the decommissioning of depleted production fields and their facilities. One of the greatest obstacles facing new entrants into the offshore oil and gas industry is the lack of a track record. To meet this challenge, the ability to seek out partners to pursue local and international opportunities through joint ventures, strategic alliances and technology sharing partnering arrangements is of great importance. It may be the difference between success and failure. 6 figs

A GLANCE AT OFFSHORE WIND TURBINE FOUNDATION STRUCTURES

Directory of Open Access Journals (Sweden)

Jianhua Zhang

2016-06-01

Full Text Available Energy poverty and climate change are crucial issues we face in our societies. Offshore wind energy has been a reliable solution to both of these problems - solving our growing energy problems while reducing CO2 emission. Innovative foundation design is one of the setbacks faced by this industry. Designing and constructing a cost effective offshore wind farm is greatly hampered by technical and infrastructural challenges, especially in foundation structures. This paper provides a detailed overview of issues related to this problem, with the aim of eliminating the frequent misunderstandings which can arise among engineers and investors working in the offshore wind energy sector. It begins by investigating the latest data and recommendations regarding the design and deployment of various kinds of offshore wind turbine (OWT foundations. It provides a framework which enables us to study the different OWT foundations, including prototypes and their limitations. Various structural failure modes are highlighted and corrosion measures are presented. Moreover, various removal methods of support structures are put forward. Finally, this paper presents the setbacks preventing the spread of offshore wind energy and the future works for offshore wind energy applications.

Extension of the Parana Basin to offshore Brazil: Implications for coalbed methane evaluation

Energy Technology Data Exchange (ETDEWEB)

Holz, M.; Kalkreuth, W.; Rolim, S.B.A. [Universidade Federal do Rio Grande do Sul, Porto Alegre (Brazil)

2010-05-15

Coalbed methane (CBM) is a worldwide exploration target of the petroleum industry. In Brazil, the most important coal-bearing succession is associated with the Permian Rio Bonito Formation of the Parana Basin. The gas-prone areas are located at the southeastern margin of the Parana Basin and possibly in the offshore region of the northern part of the Pelotas Basin. Coalfields end abruptly at the present day shoreline, a result of rifting of Gondwana and the evolution of the South Atlantic Ocean. All geologic indicators suggest that in pre-rift times the coal seams extended further eastwards, probably now lying deeply buried below the sedimentary succession of the Pelotas Basin. The present paper discusses structural, stratigraphic, seismic and aeromagenetic data that support the preservation of continental crust beneath ocean sediment. If the coal beds had similar lateral extent to known onshore coals, and coal beds extended across the projected extension of the Parana basin, and there was a conservative 5 m of cumulative coal thickness, then a potential methane volume can be estimated for this newly inferred resource. Average onshore coal gas content is 32 scf/ton (1.00 m(3)/ton). If this is similar in the offshore coal deposits, then the hypothetical methane volume in the offshore area could be in excess of 1.9 x 10(12) scf (56 x 10(9) m(3)). Metamorphism from dikes associated with rifting are potential complicating factors in these deposits, and since no borehole reaching the deep-lying strata in the offshore area are available, this is a hypothetical gas resource with a certain level of uncertainty which should be tested in the future by drilling a deep borehole.

Offshore wind energy developments

DEFF Research Database (Denmark)

Stolpe, Mathias; Buhl, Thomas; Sumer, B. Mutlu

2014-01-01

This chapter will give a brief overview of a few of the activities within offshore wind energy research, specifically 1) Support structure optimization, 2) Blade coatings for wind turbines; 3) Scour protection of foundations, 4) Offshore HVDC and 5) Offshore wind services....

Drilling reorganizes

Science.gov (United States)

Richman, Barbara T.

As the first in a proposed series of steps that would move scientific ocean drilling from its own niche within the National Science Foundation's (NSF) Directorate for Astronomical, Atmospheric, Earth, and Ocean Sciences (AAEO) into the agency's Division of Ocean Sciences, Grant Gross, division director, has been appointed acting director of the Office of Scientific Ocean Drilling (OSOD). Gross will retain the directorship of the division, which also is part of AAEO. Allen M. Shinn, Jr., OSOD director for nearly 2 years, has been reassigned effective July 10 to a position in NSF's Office of Planning and Resource Management.The move aims to tie drilling operations more closely to the science with which it is associated, Gross said. This first step is an organizational response to the current leaning toward using a commercial drilling vessel as the drilling platform, he said. Before the market for such commercial drill ships opened (Eos, February 22, 1983, p . 73), other ship options for scientific ocean drilling included refurbishing the aging Glomar Challenger or renovating, at great expense, the Glomar Explorer. A possible next step in the reorganization is to make OSOD the third section within the Ocean Sciences Division. Currently, the division is divided into the Oceanographic Facilities and Support Section and the Ocean Sciences Research Section.

"Selective Cosmopolitans": Tutors' and Students' Experience of Offshore Higher Education in Dubai

Science.gov (United States)

Kadiwal, Laila; Rind, Irfan A.

2013-01-01

As the offshore mobility of higher education has increased in recent times, the question of how it interacts with the recipient cultures has become ever more significant. Using ethnographic methods, this empirical study examined the adaptation of the UK teacher education model--the Postgraduate Certificate in Education--to the context of Dubai.…

Chew Bahir: A Key Site within the Hominin Sites and Paleolakes Drilling Project, towards a Half Million-Year Climate Record from Southern Ethiopia

Science.gov (United States)

Schaebitz, F.; Asrat, A.; Lamb, H. F.; Trauth, M. H.; Foerster, V. E.; Junginger, A.; Raub, T. D.; Gromig, R.; Viehberg, F. A.; Roberts, H. M.; Cohen, A.

2015-12-01

Chew Bahir, a saline mudflat today, is one of the five sites in East Africa, drilled within the framework of HSPDP (Hominin Site and Paleolakes Drilling Project). It is also one of the key sites of the Collaborative Research Centre (CRC-806) "Our way to Europe" aiming at the reconstruction of environmental conditions in the source region of modern man (H. sapiens). It is suggested that a changing environment could have triggered the mobility and dispersal of modern man. The oldest known fossils of anatomical modern humans (~195 ka BP) were found in the Omo basin, not more than 90km westwards of our drill site. The deposits in the tectonic basin of Chew Bahir in southern Ethiopia were cored in Nov. 2014 in two boreholes down to 280 m and 260 m below surface respectively. The overlapping long cores (drilled ~20 m apart from each other), were opened, scanned, described and sampled in low resolution in April 2015. The recovered sediments mostly contain green-greyish to light coloured and brown to reddish clays and silty clays, interbedded with some laminated mica-rich sand layers and occurrences of carbonate concretions and nodules, which decrease upcore. Here we will present a first set of results on the composite core, comprising mainly lithology and magnetic susceptibility (MS). Based on known sedimentation rates from pre-studies performed on short cores across the basin, we anticipate the deep drilled cores to cover at least 500 ka BP. Moreover, new insights into the role of post-depositional alteration, especially of clay minerals and zeolites, will be presented as a contribution to an improved understanding of formation processes. The results support the identification of wet and dry climate periods in the past. Those pronounced variations of moisture availability, are thought to have influenced the evolution and mobility of Homo sapiens sapiens.

Offshore risk assessment

CERN Document Server

Vinnem, Jan-Erik

2014-01-01

  Offshore Risk Assessment was the first book to deal with quantified risk assessment (QRA) as applied specifically to offshore installations and operations. Risk assessment techniques have been used for more than three decades in the offshore oil and gas industry, and their use is set to expand increasingly as the industry moves into new areas and faces new challenges in older regions.   This updated and expanded third edition has been informed by a major R&D program on offshore risk assessment in Norway and summarizes research from 2006 to the present day. Rooted with a thorough discussion of risk metrics and risk analysis methodology,  subsequent chapters are devoted to analytical approaches to escalation, escape, evacuation and rescue analysis of safety and emergency systems.   Separate chapters analyze the main hazards of offshore structures: fire, explosion, collision, and falling objects as well as structural and marine hazards. Risk mitigation and control are discussed, as well as an illustrat...

A novel drill design for photoacoustic guided surgeries

Science.gov (United States)

Shubert, Joshua; Lediju Bell, Muyinatu A.

2018-02-01

Fluoroscopy is currently the standard approach for image guidance of surgical drilling procedures. In addition to the harmful radiation dose to the patient and surgeon, fluoroscopy fails to visualize critical structures such as blood vessels and nerves within the drill path. Photoacoustic imaging is a well-suited imaging method to visualize these structures and it does not require harmful ionizing radiation. However, there is currently no clinical system available to deliver light to occluded drill bit tips. To address this challenge, a prototype drill was designed, built, and tested using an internal light delivery system that allows laser energy to be transferred from a stationary laser source to the tip of a spinning drill bit. Photoacoustic images were successfully obtained with the drill bit submerged in water and with the drill tip inserted into a thoracic vertebra from a human cadaver.

Surgical drill system and surgical drill bit to be used therein

NARCIS (Netherlands)

Margallo Balbas, E.; Wieringa, P.A.; French, P.J.; Lee, R.A.; Breedveld, P.

2007-01-01

Surgical drill system comprising a mechanical drill bit and means for imaging the vicinity of the drill bit tip, said means comprising: at least one optical fiber having a distal end and a proximal end, said distal end being located adjacent said drill bit tip, an optical processing unit, said

Spatial and temporal patterns of airflow across a foredune and beach surface under offshore winds: implications for aeolian sediment transport

Science.gov (United States)

Jackson, D.; Delgado-Fernandez, I.; Lynch, K.; Baas, A. C.; Cooper, J. A.; Beyers, M.

2010-12-01

The input of aeolian sediment into foredune systems from beaches represents a key component of sediment budget analysis along many soft sedimentary coastlines. Where there are significant offshore wind components in local wind regimes this is normally excluded from analysis. However, recent work has shown that if the topography of the foredune is favourable then this offshore component is steered or undergoes flow reversal through leeside eddying to give onshore transport events at the back beach under offshore flow conditions. At particular distances from the foredune crest flow reattaches to the surface to continue its incident offshore direction. The location of this reattachment point has important implications for aeolian transport of sand on the back beach and foredune toe locations. This study reports initial results where the positioning of the reattachment point is mobile and is driven by incident wind velocity (at the foredune crest) and the actual undulations of the foredune crest’s topography, dictating heterogeneous flow behaviour at the beach. Using detailed field measurements (25 Hz, three-dimensional sonic anemometry) and computational fluid dynamic modelling, a temporal and spatial pattern of reattachment positions are described. Implications for aeolian transport and dune evolution are also examined.

Deformation Mechanisms of Offshore Monopile Foundations Accounting for Cyclic Mobility Effects

DEFF Research Database (Denmark)

Barari, Amin; Bagheri, Mohsen; Rouainia, Mohamed

2017-01-01

Highlights •There has been a huge surge in the construction of marine facilities (e.g., wind turbines) in Europe. •This paper presents some new frameworks for design strategy based on performance measures for cyclic horizontally loaded monopile foundations. •A three-dimensional finite element model...... was developed to investigate the behavior of large-diameter piles. •This model accounts for nonlinear dynamic interactions in offshore platforms under harsh combined moment and horizontal environmental loads. •Magnitude of cyclic loads was found to cause a linear increase in the accumulated rotation....

Reduced abrasion drilling fluid

NARCIS (Netherlands)

2010-01-01

A reduced abrasion drilling fluid system and method of drilling a borehole by circulating the reduced abrasion drilling fluid through the borehole is disclosed. The reduced abrasion drilling fluid comprises a drilling fluid, a first additive and a weighting agent, wherein the weighting agent has a

Reduced abrasion drilling fluid

NARCIS (Netherlands)

2012-01-01

A reduced abrasion drilling fluid system and method of drilling a borehole by circulating the reduced abrasion drilling fluid through the borehole is disclosed. The reduced abrasion drilling fluid comprises a drilling fluid, a first additive and a weighting agent, wherein the weighting agent has a

Advanced Seismic While Drilling System

Energy Technology Data Exchange (ETDEWEB)

Robert Radtke; John Fontenot; David Glowka; Robert Stokes; Jeffery Sutherland; Ron Evans; Jim Musser

2008-06-30

for developing, utilizing, and exploiting the low-frequency SeismicPULSER{trademark} source in a variety of applications. Risks will be minimized since Drill Bit SWD will not interfere with the drilling operation, and can be performed in a relatively quiet environment when the pumps are turned off. The new source must be integrated with other Measurement While Drilling (MWD) tools. To date, each of the oil companies and service companies contacted have shown interest in participating in the commercialization of the low-frequency SeismicPULSER{trademark} source. A technical paper has been accepted for presentation at the 2009 Offshore Technology Conference (OTC) in a Society of Exploration Geologists/American Association of Petroleum Geophysicists (SEG/AAPG) technical session.

A framework for offshore vendor capability development

Science.gov (United States)

Yusuf Wibisono, Yogi; Govindaraju, Rajesri; Irianto, Dradjad; Sudirman, Iman

2016-02-01

Offshore outsourcing is a common practice conducted by companies, especially in developed countries, by relocating one or more their business processes to other companies abroad, especially in developing countries. This practice grows rapidly owing to the ease of accessing qualified vendors with a lower cost. Vendors in developing countries compete more intensely to acquire offshore projects. Indonesia is still below India, China, Malaysia as main global offshore destinations. Vendor capability is among other factors that contribute to the inability of Indonesian vendor in competing with other companies in the global market. Therefore, it is essential to study how to increase the vendor's capability in Indonesia, in the context of global offshore outsourcing. Previous studies on the vendor's capability mainly focus on capabilities without considering the dynamic of capabilities due to the environmental changes. In order to be able to compete with competitors and maintain the competitive advantage, it is necessary for vendors to develop their capabilities continuously. The purpose of this study is to develop a framework that describes offshore vendor capability development along the client-vendor relationship stages. The framework consists of three main components, i.e. the stages of client-vendor relationship, the success of each stage, and the capabilities of vendor at each stage.

Employability of offshore service sector workers in the Philippines: opportunities for upward labour mobility or dead-end jobs?

NARCIS (Netherlands)

Beerepoot, N.; Hendriks, M.

2013-01-01

Critical concerns have been raised about the quality of employment in the offshore service sector in developing countries, suggesting that many activities have an inherent paradox of highly educated workers performing low-skilled jobs. Based on empirical data collected in the offshore service sector

Current trends in offshore technology

International Nuclear Information System (INIS)

Korsgaard, J.

1994-01-01

Although this is a technical symposium concerning advances in the technology of producing oil and gas offshore, a keynote address would not be complete without mentioning non-technical factors which are extremely important for the business of producing oil and gas offshore. These are political factors and economic factors. Offshore operations are an easy target for political forces that are opposed to marine operations involving the production and transfer of hydrocarbons. For example, the oil pollution act of 1990 was a reaction to the Exxon Valdez grounding in Alaska and this act has added significantly to the risk and cost of operating offshore. Another example of this is that it is becoming more and more difficult to dispose of produced water offshore. Producing oil and gas offshore is a business that competes with other energy sources such as coal and oil and gas from wells on land. The offshore oil can only compete with these other resources by providing the same product at a competitive price. Since offshore operations are inherently more costly than land operations, the offshore oil field or gas field must be significantly larger than a land field in order to be produced. Also the offshore oil field or gas field is more susceptible to environmental risks from weather. On a more positive note, there are technical developments which are taking place and have continuously taken place to make offshore oil and gas both more economic and safer to produce. These developments are briefly discussed

Offshoring in the Semiconductor Industry: A Historical Perspective

OpenAIRE

Brown, Clair; Linden, Greg

2005-01-01

Semiconductor design is a frequently-cited example of the new wave of offshoring and foreign-outsourcing of service sector jobs. It is certainly a concern to U.S. design engineers themselves. In addition to the current wave of white-collar outsourcing, the industry also has a rich experience with offshoring of manufacturing activity. Semiconductor companies were among the first to invest in offshore facilities to manufacture goods for imports back to the U.S. A brief review of these...

Investigating Miocene Mediterranean-Atlantic Gateway Exchange (IMMAGE) - an amphibious drilling proposal

Science.gov (United States)

Flecker, Rachel

2017-04-01

Today Mediterranean seawater flows out through the Gibraltar Straits, forming a saline plume at intermediate depths in the Atlantic. The plume's sedimentary record of distinctive, contouritic deposits has recently been recovered during IODP Leg 339 in the Gulf of Cadiz documenting a Mediterranean contribution to Atlantic thermohaline circulation since the Pliocene. However, before the Pliocene, the conduit for Mediterranean-Atlantic exchange is unclear. Gibraltar may have already been open, but two additional marine corridors also existed through northern Morocco and southern Spain. The restriction and closure of these Miocene connections resulted in extreme salinity fluctuations in the Mediterranean, leading to the precipitation of thick evaporites. This event is known as the Messinian Salinity Crisis (MSC) and recovering a complete record of the MSC is the target of current IODP drilling proposals (e.g. DREAM). Understanding both the causes of high-amplitude salinity change in the Mediterranean and its global consequences for thermohaline circulation in the Atlantic is dependent on recovering a complete record of Mediterranean-Atlantic exchange before, during and after the MSC. This key objective of the IMMAGE drilling proposal requires core recovery on-shore at the mouths of the Betic and Rifian corridors which are now exposed on land, as well as offshore, in the Alborán Sea and on the Atlantic continental margin. Consequently to meet this objective, an amphibious drilling strategy is necessary, involving both IODP and ICDP targets. In addition to allowing us to reconstruct Mediterranean-Atlantic exchange during high amplitude salinity fluctuations and identify the conduit through which exchange occurred, the sediments recovered from IMMAGE drilling will also provide us with a unique and explicit test for ocean physics hypotheses describing the location, size and velocity of overflow plumes under conditions where the density contrast between the two water

Hydraulic lifter of a drilling unit

Energy Technology Data Exchange (ETDEWEB)

Velikovskiy, L S; Demin, A V; Shadchinov, L M

1979-01-08

The invention refers to drilling equipment, in particular, devices for lowering and lifting operations during drilling. A hydraulic lifter of the drilling unit is suggested which contains a hydraulic cylinder, pressure line and hollow plunger whose cavities are hydraulically connected. In order to improve the reliability of the hydraulic lifter by balancing the forces of compression in the plunger of the hydraulic cylinder, a closed vessel is installed inside the plunger and rigidly connected to its ends. Its cavity is hydraulically connected to the pressure line.

Outsourcing software development offshore making IT work

CERN Document Server

Gold, Tandy

2004-01-01

THE OFFSHORE IMPERATIVECrunching the Offshore Numbers: What the Financials PortendWelcome to the Definitive Guide on Offshore OutsourcingSetting the Stage: The Compelling Offshore StoryOffshore Outsourcing versus Traditional IT OutsourcingChallenges of Offshore OutsourcingChapter SummaryGetting Started in OffshoreExecutive Support and Communications: The Key to SuccessA Look at an Example of Enlightened Leadership: Handling Employee Impact at a Northeast Utilities CompanyWell-Planned and Executed Communications: A Critical Success Factor for Offshore Program InitiationEstablishing the Offshore

Environmental Measurement-While-Drilling System and Horizontal Directional Drilling Technology Demonstration, Hanford Site

International Nuclear Information System (INIS)

Williams, C.V.; Lockwood, G.J.; Normann, R.A.; Myers, D.A.; Gardner, M.G.; Williamson, T.; Huffman, J.

1999-01-01

The Environmental Measurement-While-Drilling (EMWD) system and Horizontal Directional Drilling (HDD) were successfully demonstrated at the Mock Tank Leak Simulation Site and the Drilling Technology Test Site, Hanford, Washington. The use of directional drilling offers an alternative to vertical drilling site characterization. Directional drilling can develop a borehole under a structure, such as a waste tank, from an angled entry and leveling off to horizontal at the desired depth. The EMWD system represents an innovative blend of new and existing technology that provides the capability of producing real-time environmental and drill bit data during drilling operations. The technology demonstration consisted of the development of one borehole under a mock waste tank at a depth of approximately minus8 m (minus27 ft.), following a predetermined drill path, tracking the drill path to within a radius of approximately1.5 m (5 ft.), and monitoring for zones of radiological activity using the EMWD system. The purpose of the second borehole was to demonstrate the capability of drilling to a depth of ∼ -21 m (-70 ft.), the depth needed to obtain access under the Hanford waste tanks, and continue drilling horizontally. This report presents information on the HDD and EMWD technologies, demonstration design, results of the demonstrations, and lessons learned

Feasibility of Optimizing Recovery and Reserves from a Mature and Geological Complex Multiple Turbidite Offshore Calif. Reservoir through the Drilling and Completion of a Trilateral Horizontal Well, Class III

Energy Technology Data Exchange (ETDEWEB)

Pacific Operators Offshore, Inc.

2001-04-04

The intent of this project was to increase production and extend the economic life of this mature field through the application of advanced reservoir characterization and drilling technology, demonstrating the efficacy of these technologies to other small operators of aging fields. Two study periods were proposed; the first to include data assimilation and reservoir characterization and the second to drill the demonstration well. The initial study period showed that a single tri-lateral well would not be economically efficient in redevelopment of Carpinteria's multiple deep water turbidite sand reservoirs, and the study was amended to include the drilling of a series of horizontal redrills from existing surplus well bores on Pacific Operators' Platform Hogan.

Domestic R&D and Offshoring

DEFF Research Database (Denmark)

Junge, Martin; Sørensen, Anders

2017-01-01

survey and register data. No evidence is found for a lower probability of own R&D after offshoring takes place compared to before. Moreover, offshoring does not lead to lower R&D intensity in general. However, firms that offshore R&D activity have larger R&D intensity after offshoring has taken place...

Activity plan: Directional drilling and environmental measurements while drilling

International Nuclear Information System (INIS)

Myers, D.A.

1998-01-01

This activity plan describes the testing of directional drilling combined with environmental measurements while drilling at two Hanford Site locations. A cold test is to be conducted at the 105A Mock Tank Leak Facility in the 200 East Area. A hot test is proposed to be run at the 216-B-8 tile field north of the 241-B Tank Farm in 200 East Area. Criteria to judge the success, partial success or failure of various aspects of the test are included. The TWRS program is assessing the potential for use of directional drilling because of an identified need to interrogate the vadose zone beneath the single-shell tanks. Because every precaution must be taken to assure that investigation activities do not violate the integrity of the tanks, control of the drill bit and ability to follow a predetermined drill path are of utmost importance and are being tested

Activity plan: Directional drilling and environmental measurements while drilling

Energy Technology Data Exchange (ETDEWEB)

Myers, D.A.

1998-07-16

This activity plan describes the testing of directional drilling combined with environmental measurements while drilling at two Hanford Site locations. A cold test is to be conducted at the 105A Mock Tank Leak Facility in the 200 East Area. A hot test is proposed to be run at the 216-B-8 tile field north of the 241-B Tank Farm in 200 East Area. Criteria to judge the success, partial success or failure of various aspects of the test are included. The TWRS program is assessing the potential for use of directional drilling because of an identified need to interrogate the vadose zone beneath the single-shell tanks. Because every precaution must be taken to assure that investigation activities do not violate the integrity of the tanks, control of the drill bit and ability to follow a predetermined drill path are of utmost importance and are being tested.

Offshoring and International Competitiveness

DEFF Research Database (Denmark)

Ørberg Jensen, Peter D.; Pedersen, Torben

2012-01-01

During the past decade, offshoring has become an established business practice. Yet it is still more common to offshore less advanced tasks compared with offshoring more advanced tasks, i.e., tasks closer to the core activities of the firm. The latter is a new phenomenon which raises many new iss...

A novel floating offshore wind turbine concept

DEFF Research Database (Denmark)

Vita, Luca; Schmidt Paulsen, Uwe; Friis Pedersen, Troels

2009-01-01

This paper will present a novel concept of a floating offshore wind turbine. The new concept is intended for vertical-axis wind turbine technology. The main purpose is to increase simplicity and to reduce total costs of an installed offshore wind farm. The concept is intended for deep water...... and large size turbines....

A Fast Inspection of Tool Electrode and Drilling Depth in EDM Drilling by Detection Line Algorithm.

Science.gov (United States)

Huang, Kuo-Yi

2008-08-21

The purpose of this study was to develop a novel measurement method using a machine vision system. Besides using image processing techniques, the proposed system employs a detection line algorithm that detects the tool electrode length and drilling depth of a workpiece accurately and effectively. Different boundaries of areas on the tool electrode are defined: a baseline between base and normal areas, a ND-line between normal and drilling areas (accumulating carbon area), and a DD-line between drilling area and dielectric fluid droplet on the electrode tip. Accordingly, image processing techniques are employed to extract a tool electrode image, and the centroid, eigenvector, and principle axis of the tool electrode are determined. The developed detection line algorithm (DLA) is then used to detect the baseline, ND-line, and DD-line along the direction of the principle axis. Finally, the tool electrode length and drilling depth of the workpiece are estimated via detected baseline, ND-line, and DD-line. Experimental results show good accuracy and efficiency in estimation of the tool electrode length and drilling depth under different conditions. Hence, this research may provide a reference for industrial application in EDM drilling measurement.

Too much or too little of R&D offshoring : The impact of captive offshoring and contract offshoring on innovation performance

NARCIS (Netherlands)

Steinberg, Philip; Procher, Vivien D.; Urbig, Diemo

2017-01-01

Innovating firms may acquire foreign knowledge and improve their innovation performance by offshoring their R&D activities to their own foreign affiliates (captive offshoring) as well as by contracting out their R&D to external foreign parties (contract offshoring). This study examines the impact of

Offshore production flares: a PETROBRAS review

Energy Technology Data Exchange (ETDEWEB)

Pagot, Paulo R.; Burmann, Clovis P.; Araujo, Paulo Bento de; Motomura, Tsukasa [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2008-07-01

The purpose of the present work is to briefly present the offshore flare system technological evolution and the main design criteria for flare and its supporting structure. In order to perform the aimed task, this work was divided into two parts: the first part presents the technological evolution of the offshore production flares and the second one discusses the flare system designing criteria. The evolution of the technology associated to the offshore production flares is organized by the authors just dividing the history in four chronological phases. Each phase is defined by the predominant use of the, by the time, most up-to-date technological alternative and it will be described with the help of sketches, drawings, photographs, data and information about the platforms where such technologies were applied. The second part of the present work discusses the dimensional criteria, interesting aspects and flaws of the offshore flare systems in two different fields, which are: definition of the flare system capacity; and flow and thermal design of the flare system. (author)

Slow drilling speeds for single-drill implant bed preparation. Experimental in vitro study.

Science.gov (United States)

Delgado-Ruiz, R A; Velasco Ortega, E; Romanos, G E; Gerhke, S; Newen, I; Calvo-Guirado, J L

2018-01-01

To evaluate the real-time bone temperature changes during the preparation of the implant bed with a single-drill protocol with different drill designs and different slow drilling speeds in artificial type IV bone. For this experimental in vitro study, 600 implant bed preparations were performed in 10 bovine bone disks using three test slow drilling speeds (50/150/300 rpm) and a control drilling speed (1200 rpm). The temperature at crestal and apical areas and time variations produced during drilling with three different drill designs with similar diameter and length but different geometry were recorded with real-life thermographic analysis. Statistical analysis was performed by two-way analysis of variance. Multiple comparisons of temperatures and time with the different drill designs and speeds were performed with the Tukey's test. T Max values for the control drilling speed with all the drill designs (D1 + 1200; D2 + 1200; D3 + 1200) were higher compared to those for the controls for 11 ± 1.32 °C (p drilling at 50 rpm resulted in the lowest temperature increment (22.11 ± 0.8 °C) compared to the other slow drilling speeds of 150 (24.752 ± 1.1 °C) and 300 rpm (25.977 ± 1.2 °C) (p drilling speeds compared to that for the control drilling speed. Slow drilling speeds required significantly more time to finish the preparation of the implant bed shown as follows: 50 rpm > 150 rpm > 300 rpm > control (p drill protocol with slow drilling speeds (50, 150, and 300 rpm) without irrigation in type IV bone increases the temperature at the coronal and apical levels but is below the critical threshold of 47 °C. The drill design in single-drill protocols using slow speeds (50, 150, and 300 rpm) does not have an influence on the thermal variations. The time to accomplish the implant bed preparation with a single-drill protocol in type IV bone is influenced by the drilling speed and not by the drill design. As the speed decreases, then

Drilling the North Anatolian Fault

Directory of Open Access Journals (Sweden)

Mustafa Aktar

2008-07-01

Full Text Available An international workshop entitled “GONAF: A deep Geophysical Observatory at the North Anatolian Fault”, was held 23–27 April 2007 in Istanbul, Turkey. The aim of this workshop was to refine plans for a deep drilling project at the North Anatolian Fault Zone (NAFZ in northwestern Turkey. The current drilling target is located in the Marmara Sea offshore the megacity of Istanbul in the direct vicinity of the main branch of the North Anatolian Fault on the PrinceIslands (Figs. 1 and 2.The NAFZ represents a 1600-km-long plate boundary that slips at an average rate of 20–30 mm·yr-1 (McClusky et al., 2000. It has developed in the framework of the northward moving Arabian plate and the Hellenic subduction zone where the African lithosphere is subducting below the Aegean. Comparison of long-term slip rates with Holocene and GPS-derived slip rates indicate an increasing westwardmovement of the Anatolian plate with respect to stable Eurasia. During the twentieth century, the NAFZ has ruptured over 900 km of its length. A series of large earthquakes starting in 1939 near Erzincan in Eastern Anatolia propagated westward towards the Istanbul-Marmara region in northwestern Turkey that today represents a seismic gap along a ≥100-km-long segment below the Sea of Marmara. This segment did not rupture since 1766 and, if locked, may have accumulated a slip deficit of 4–5 m. It is believed being capable of generating two M≥7.4 earthquakes within the next decades (Hubert-Ferrari et al., 2000; however, it could even rupture in a large single event (Le Pichon et al., 1999.

Investment in exploration-production and refining 2014

International Nuclear Information System (INIS)

Hureau, Geoffroy; Serbutoviez, Sylvain; Silva, Constancio; Maisonnier, Guy

2014-11-01

IFPEN analyses in this study the 2014 evolution of global investment in the field of exploration-production and refining: 1 - Changes in oil and gas prices: General background: weak economy and global disorder, Oil prices: fundamentals that could help to relax oil prices?, Gas prices: fall in Europe, stability in Japan, increase in the US; 2 - Exploration and production - Slowdown in growth: moderate rise in investment in 2014, exploration - Discoveries in 2014, Russia: sanctions will have limited short term impact, implications of the reforms to the Mexican energy sector; 3 - Drilling activity and market throughout the world: onshore and offshore drilling (Number of wells drilled throughout the world, Number of onshore wells, Number of offshore wells, Drilling, equipment and well services markets, Onshore drilling market, Offshore drilling market, Fracking market), Geophysical activity and the geophysical market, Offshore construction activity and the offshore construction market (Offshore construction activities, Rig construction activity, Floating Platform Systems (FPS), Sub-sea constructions, Offshore construction market); 4 - Refining - Significant increase in spending: increase in industrial costs, a slowdown in the increase in excess capacity in the future?, A bleak future for the european refining sector

Program and abstracts of the offshore oil and gas environmental effects monitoring workshop : approaches and technologies

International Nuclear Information System (INIS)

2003-01-01

The offshore petroleum industry in eastern Canada has expanded rapidly, with exploration and production activities taking place over a wide range of oceanographic conditions. This workshop, hosted by Canada's largest marine research institute, was held to advance the understanding of environmental impacts from offshore oil and gas activity. In particular, it examined how information derived from environmental effects monitoring (EEM) programs contribute to improved drilling and production operations, mitigation measures, and the revision of regulations for waste treatment. The workshop examined if EEM programs are providing valuable information, and how they can be improved. The themes of the 3 sessions which focused on ways to carry out EEM were: (1) EEM and environmental management, (2) EEM methodologies and lessons learned, and (3) EEM methodologies and technologies. Participants form around the world identified priority research needs and coordinated collaborative research efforts. Approximately 70 papers and posters were presented at the workshop, of which 19 have been indexed separately for inclusion in this database (Author)

Offshore wind energy prospects

International Nuclear Information System (INIS)

Gaudiosi, Gaetano

1999-01-01

In last two years offshore wind energy is becoming a focal point of national and non national organisations particularly after the limitations of fossil fuel consumption, adopted by many developed countries after Kyoto conference at the end of 1997 on global climate change. North Europe is particularly interested in offshore for the limited land areas still available, due to the intensive use of its territory and its today high wind capacity. Really the total wind capacity in Europe could increase from the 1997 value of 4450 MW up to 40 000 MW within 2010, according the White Paper 1997 of the European Commission; a significant percentage (25%) could be sited offshore up to 10 000 MW, because of close saturation of the land sites at that time. World wind capacity could increase from the 1997 value of 7200 MW up to 60 000 MW within 2010 with a good percentage (20%) offshore 12 000 MW. In last seven years wind capacity in shallow water of coastal areas has reached 34 MW. Five wind farms are functioning in the internal seas of Netherlands, Denmark, Sweden; however such siting is mostly to be considered as semi-offshore condition. Wind farms in real offshore sites, open seas with waves and water depth over 10 m, are now proposed in North Sea at 10-20 km off the coasts of Netherlands, Denmark using large size wind turbine (1-2 MW). In 1997 an offshore proposal was supported in Netherlands by Greenpeace after the OWEMES '97 seminar, held in Italy on offshore wind in the spring 1997. A review is presented in the paper of European offshore wind programs with trends in technology, economics and siting effects. (Author)

Petroleum prospectivity of the onshore Gaspe and offshore Anticosti Basins, eastern Canada

International Nuclear Information System (INIS)

Durling, P.; Martel, T.; Waldron, J.W.F.

1998-01-01

The development of oil and gas reserves on the Scotian Shelf and the Grand Banks of Newfoundland has sparked a renewed interest in the onshore Gaspe-Connecticut Valley Synclinorium (GCVS) and the offshore Anticosti Basin. The geologic history of each basin was described and some of the geological relationships that suggest the presence of hydrocarbon resources in the area were reviewed. The Anticosti Basin developed in a rift and open marine shelf environment during the early Cambrian period. Petroleum exploration in the Basin began in the early 1960s when Imperial Oil collected 435 km of single channel seismic reflection data - enough to identify several drilling locations. Eight wells were drilled on the island which resulted in a number of shows of oil and gas. The GCVS was developed within the Appalachian Orogen and is comprised of fine grained siliciclastic turbidites. The structural geology of the GCVS is more complicated than the Anticosti Basin. Petroleum exploration in the GCVS has, for the most part, been in the eastern part of the Gaspe Peninsula where one producing well is located. The central part is mainly unexplored for petroleum resources

Assessing offshore wind potential

International Nuclear Information System (INIS)

Adelaja, Adesoji; McKeown, Charles; Calnin, Benjamin; Hailu, Yohannes

2012-01-01

Quantifying wind potential is a pivotal initial step in developing and articulating a state’s policies and strategies for offshore wind industry development. This is particularly important in the Great Lakes States where lessons from other offshore environments are not directly applicable. This paper presents the framework developed for conducting a preliminary assessment of offshore wind potential. Information on lake bathymetry and wind resources were combined in simulating alternative scenarios of technically feasible turbine construction depths and distance concerns by stakeholders. These yielded estimates of developable offshore wind areas and potential power generation. While concerns about the visibility of turbines from shore reduce the power that can be generated, engineering solutions that increase the depths at which turbines can be sited increase such potential power output. This paper discusses the costs associated with technical limitations on depth and the social costs related to public sentiments about distance from the shoreline, as well as the possible tradeoffs. The results point to a very large untapped energy resource in the Michigan’s Great Lakes, large enough to prompt policy action from the state government. - Highlights: ▶ We build a theoretical framework for modeling offshore wind power production. ▶ Illustration of the impact of technology and social limitations on offshore wind energy development. ▶ Geospatial modeling of the offshore wind potential of the Great Lakes.

Wind energy in offshore grids

DEFF Research Database (Denmark)

Schröder, Sascha Thorsten

special characteristics of offshore grids. With an operational real options approach, it is furthermore illustrated how different support schemes and connections to additional countries affect the investment case of an offshore wind farm and the income of the transmission system operator. The investment...... and investment implications under different regulatory frameworks are a hitherto underrepresented research field. They are addressed by this thesis. Offshore grids between several countries combine the absorption of wind energy with international power trading. However, the inclusion into an offshore grid......This cumulative PhD thesis deals with wind integration in offshore grids from an economic point of view. It is composed of a generic part and eight papers. As the topic has mostly been analysed with a focus on topology and technical issues until now, market-operational questions in offshore grids...

Impact of the oil price and fiscal facilities on offshore mining at the Dutch Continental Shelf

International Nuclear Information System (INIS)

Cate, Arie ten; Mulder, Machiel

2007-01-01

The surge in the oil price has raised questions about the magnitude of global reserves of oil. According to some analysts, the current high oil prices indicate a looming decline in the global production of oil. Others believe, however, that the increased level of the oil price encourages exploration and production activities, bringing the oil price to a lower equilibrium level in the near future. In this paper, we assess the impact of the unit profit (depending on the oil price) as well as fiscal facilities on the level of exploration and development drillings in the Dutch Continental Shelf. We conducted an econometric analysis of exploration and development drillings in the Dutch Continental Shelf over the period 1981-2003. Except a few fiscal changes, the regulatory framework for offshore activities in the Netherlands, the so-called 'small fields policy' was unchanged in this period. We find that the expected unit profit based on a moving average of the oil price significantly explains the level of both exploration and development drillings. In addition, the analysis suggests that fiscal facilities have only a temporary effect on exploration activities but are more important for development activities. We conclude that the oil price is a major economic incentive for activities of the mining industry

Drilling Automation Tests At A Lunar/Mars Analog Site

Science.gov (United States)

Glass, B.; Cannon, H.; Hanagud, S.; Lee, P.; Paulsen, G.

2006-01-01

Future in-situ lunar/martian resource utilization and characterization, as well as the scientific search for life on Mars, will require access to the subsurface and hence drilling. Drilling on Earth is hard - an art form more than an engineering discipline. The limited mass, energy and manpower in planetary drilling situations makes application of terrestrial drilling techniques problematic. The Drilling Automation for Mars Exploration (DAME) project is developing drilling automation and robotics for projected use in missions to the Moon and Mars in the 2011-15 period. This has been tested recently, drilling in permafrost at a lunar/martian analog site (Haughton Crater, Devon Island, Canada).

Drilling cost analysis

International Nuclear Information System (INIS)

Anand, A.B.

1992-01-01

Drilling assumes greater importance in present day uranium exploration which emphasizes to explore more areas on the basis of conceptual model than merely on surface anomalies. But drilling is as costly as it is important and consumes a major share (50% to 60%) of the exploration budget. As such the cost of drilling has great bearing on the exploration strategy as well as on the overall cost of the project. Therefore, understanding the cost analysis is very much important when planning or intensifying an exploration programme. This not only helps in controlling the current operations but also in planning the budgetary provisions for future operations. Also, if the work is entrusted to a private party, knowledge of in-house cost analysis helps in fixing the rates of drilling in different formations and areas to be drilled. Under this topic, various factors that contribute to the cost of drilling per meter as well as ways to minimize the drilling cost for better economic evaluation of mineral deposits are discussed. (author)

The Hidden Costs of Offshoring

DEFF Research Database (Denmark)

Møller Larsen, Marcus; Manning, Stephan; Pedersen, Torben

2011-01-01

of offshoring. Specifically, we propose that hidden costs can be explained by the combination of increasing structural, operational and social complexity of offshoring activities. In addition, we suggest that firm orientation towards organizational design as part of an offshoring strategy and offshoring......This study seeks to explain hidden costs of offshoring, i.e. unexpected costs resulting from the relocation of business tasks and activities outside the home country. We develop a model that highlights the role of complexity, design orientation and experience in explaining hidden costs...... experience moderate the relationship between complexity and hidden costs negatively i.e. reduces the cost generating impact of complexity. We develop three hypotheses and test them on comprehensive data from the Offshoring Research Network (ORN). In general, we find support for our hypotheses. A key result...

Case drilling - an innovative approach to reducing drilling costs

Energy Technology Data Exchange (ETDEWEB)

Madell, G.; Tessari, R. M. [Tesco Corp., Calgary, AB (Canada); Warren, T. [Tesco Drilling Technology, Calgary, AB (Canada)

1999-11-01

Casing drilling is introduced as a new drilling technique that uses standard oil field casing to simultaneously drill and case the well. The technology includes both rig and downhole equipment, customized to function effectively as an integrated drilling system. This paper describes the testing program designed to identify and overcome technical challenges. Although not fully optimized, it appears that the system is functional. Test results indicate the need for improvements in the pump down cement float equipment and the tools and procedures for drilling up the cement plugs. The pump down latch and retrieval system also needs to be further developed and tested for high angle directional applications. Cost savings in the range of 10 to 15 per cent are expected for trouble-free wells. By eliminating the cost of unscheduled events encountered in troublesome wells, cost savings may reach as high as 30 per cent. 3 refs., 7 figs.

Global offshore pipeline markets

International Nuclear Information System (INIS)

Knight, R.; Parsons, B.

2001-01-01

In this article, two experts forecast a recovery in the offshore pipeline market followed by accelerating growth. A number of clearly definable macro trends are affecting the world offshore oil and gas industry and will be of considerable significance to the offshore pipelines industry. The authors' view is of markets that show every chance of enjoying long-term growth prospects driven by the fundamentals of a continuing increase in demand for offshore oil and gas. The offshore industry however has a highly cyclical nature, due to the impact of variations in oil and gas prices and the differing state of maturity of individual regions. Therefore those companies that are able to offer the widest range of pipe types and diameters and methods of installation across the greatest range of geographic markets are likely to prosper most. Thus, this continues to be a market best suited to those able to operate on a global scale and make a corporate commitment measured in decades

Offshoring research directions

NARCIS (Netherlands)

Velthuijsen, Hugo

2012-01-01

Outsourcing and offshoring provide companies with ways to achieve their business objectives better or more cost effectively or despite a shortage of specific resources. From a research point of view, outsourcing and offshoring have mostly been studied as something that large companies do, not small

New optimized drill pipe size for deep-water, extended reach and ultra-deep drilling

Energy Technology Data Exchange (ETDEWEB)

Jellison, Michael J.; Delgado, Ivanni [Grant Prideco, Inc., Hoston, TX (United States); Falcao, Jose Luiz; Sato, Ademar Takashi [PETROBRAS, Rio de Janeiro, RJ (Brazil); Moura, Carlos Amsler [Comercial Perfuradora Delba Baiana Ltda., Rio de Janeiro, RJ (Brazil)

2004-07-01

A new drill pipe size, 5-7/8 in. OD, represents enabling technology for Extended Reach Drilling (ERD), deep water and other deep well applications. Most world-class ERD and deep water wells have traditionally been drilled with 5-1/2 in. drill pipe or a combination of 6-5/8 in. and 5-1/2 in. drill pipe. The hydraulic performance of 5-1/2 in. drill pipe can be a major limitation in substantial ERD and deep water wells resulting in poor cuttings removal, slower penetration rates, diminished control over well trajectory and more tendency for drill pipe sticking. The 5-7/8 in. drill pipe provides a significant improvement in hydraulic efficiency compared to 5-1/2 in. drill pipe and does not suffer from the disadvantages associated with use of 6-5/8 in. drill pipe. It represents a drill pipe assembly that is optimized dimensionally and on a performance basis for casing and bit programs that are commonly used for ERD, deep water and ultra-deep wells. The paper discusses the engineering philosophy behind 5-7/8 in. drill pipe, the design challenges associated with development of the product and reviews the features and capabilities of the second-generation double-shoulder connection. The paper provides drilling case history information on significant projects where the pipe has been used and details results achieved with the pipe. (author)

South African drilling

International Nuclear Information System (INIS)

Anon.

1984-01-01

According to the president of the South African Drilling Association, the drilling industry is meeting head-on the challenges created by the worldwide recession. The paper is a synopsis of several of the papers presented at the SADA symposium and a look at several mining-related drilling projects in South Africa. These papers include grouting techniques, the use of impregnated bits in hard rock drilling, tunnel boring for mines, surveying improvement methods and the use of explosives to increase groundwater yield

Mobile computing device as tools for college student education: a case on flashcards application

Science.gov (United States)

Kang, Congying

2012-04-01

Traditionally, college students always use flash cards as a tool to remember massive knowledge, such as nomenclature, structures, and reactions in chemistry. Educational and information technology have enabled flashcards viewed on computers, like Slides and PowerPoint, works as tunnels of drilling and feedback for the learners. The current generation of students is more capable of information technology and mobile computing devices. For example, they use their Mobile phones much more intensively everyday day. Trends of using Mobile phone as an educational tool is analyzed and a educational technology initiative is proposed, which use Mobile phone flash cards applications to help students learn biology and chemistry. Experiments show that users responded positively to these mobile flash cards.

EWeA Offshore 2013 - Side event: 'Offshore wind energy - Potentialities and industrial opportunities in France and in Germany. French-German cross perspectives

International Nuclear Information System (INIS)

Genachte, Anne-Benedicte; Kavafyan, Philippe; Wagner, Andreas; Bour, Gregoire

2013-01-01

At the EWEA Offshore 2013 exhibition, the French-German office for Renewable energies (OFAEnR) organised a side-conference on Offshore wind energy and its Potentialities and industrial opportunities in France and in Germany. In the framework of this French-German exchange of experience, about 50 participants exchanged views on the conditions for the development of a durable offshore wind energy industry both in France and in Germany. This document brings together the available presentations (slides) made during this event: 1 - Supporting industrial development of offshore wind in Europe (Anne-Benedicte Genachte); 2 - Offshore wind energy: the Bremerhaven experience. An asset for the deployment of a complete industrial field in France (Philippe Kavafyan); 3 - Status, Prospects and Challenges for Offshore Wind energy in Germany - incl. Legal Framework and Presentation of cost reduction study results (Andreas Wagner); 4 - Offshore grid connection in Germany - Challenges and recommendations (Gregoire Bour)

Automatic identification of otologic drilling faults: a preliminary report.

Science.gov (United States)

Shen, Peng; Feng, Guodong; Cao, Tianyang; Gao, Zhiqiang; Li, Xisheng

2009-09-01

A preliminary study was carried out to identify parameters to characterize drilling faults when using an otologic drill under various operating conditions. An otologic drill was modified by the addition of four sensors. Under consistent conditions, the drill was used to simulate three important types of drilling faults and the captured data were analysed to extract characteristic signals. A multisensor information fusion system was designed to fuse the signals and automatically identify the faults. When identifying drilling faults, there was a high degree of repeatability and regularity, with an average recognition rate of >70%. This study shows that the variables measured change in a fashion that allows the identification of particular drilling faults, and that it is feasible to use these data to provide rapid feedback for a control system. Further experiments are being undertaken to implement such a system.

Scientific Drilling with the Sea Floor Drill Rig MeBo

Directory of Open Access Journals (Sweden)

Gerold Wefer

2007-09-01

Full Text Available In March 2007 the sea floor drill rig MeBo (short for “Meeresboden-Bohrgerät”, ‘sea floor drill rig’ in German returned from a 17-day scientific cruise with the new German research vessel Maria S. Merian. Four sites between 350 m and 1700 m water depth were sampled at the continental slope off Morocco by push coring and rotary drilling. Up to 41.5-m-long sediment cores were recovered from Miocene, Pliocene, and Pleistocene marls. MeBo bridges the gapbetween conventional sampling methods from standard multipurpose research vessels (gravity corer, piston corer, dredges and drill ships. Most bigger research vessels will be able to support deployment of the MeBo. Since the drill system can be easily transported within 20-ft containers, worldwide operation from vessels of opportunity is possible. With the MeBo a new system is available for marine geosciences that allows the recovery of high quality samples from soft sediments and hard rock from the deep sea withoutrelying on the services of expensive drilling vessels.

Drilling trends in the nineties

International Nuclear Information System (INIS)

1993-01-01

At a conference on various aspects of well drilling in the 1990s, papers were presented on drilling waste management, well completion and workovers, drilling fluids, drilling rig equipment and design, drilling mechanics, drill stem testing and materials, cementing, business management, health and safety, environmental issues, and directional drilling technology. Separate abstracts have been prepared for 46 papers from this conference

Comparison of the effects of drilling fluid on macrobenthic invertebrates associated with the seagrass, Thalassia testudinum, in the laboratory and field

International Nuclear Information System (INIS)

Weber, D.E.; Flemer, D.A.; Bundick, C.M.

1992-01-01

The structure of a macrobenthic invertebrate community associated with the seagrass, Thalassia testudinum, was evaluated under laboratory and field conditions. The research focused on: (1) the effects of pollution stress from a representative drilling fluid used in offshore oil and gas operations, and (2) a comparison of responses of the seagrass-invertebrate community in the laboratory and field. The numbers of macrobenthic invertebrates were suppressed by drilling fluid at both exposure periods in the laboratory, but inhibitory effects were absent in the field. Invertebrate densities in the field were similar among control and treated plots, and were much lower than densities occurring in the laboratory control. In most instances, species richness values were similar in the field and laboratory at the end of each 6 and 12 week period

Offshore Q ＆ A

Institute of Scientific and Technical Information of China (English)

AmberStohr

2003-01-01

Equity International, Asia, is a leading financial service provider in China, offering planning expertise for expatriates on investing their income and savings. I recently sat down with four senior wealth managers in Shanghai to discuss Equity's approach to offshore investing.

Investment in exploration-production and refining 2013

International Nuclear Information System (INIS)

Hureau, Geoffroy; Serbutoviez, Sylvain; Silva, Constancio; Maisonnier, Guy

2013-10-01

IFPEN analyses in this study the 2013 evolution of global investment in the field of exploration-production and refining. 1 - Changes in oil and gas prices; 2 - Exploration production: a new year of growth: the increase in investments continues into 2013, exploration - Discoveries in 2013, 1978 - 2012: Investments - Production - Price; 3 - Main markets in the upstream oil equipment and services sector: introduction, drilling (Drilling activity, Number of wells drilled throughout the world, Number of onshore wells, Number of offshore wells, Drilling markets, equipment and services for wells, Onshore drilling market, Offshore drilling market, Fracking market); Geophysical market (Geophysical activity, Geophysical market); Offshore construction (Offshore construction activities, Fixed platforms (Jack-ups), Floating Platform Systems (FPS), Sub-sea constructions, Offshore construction market); Conclusion; 4 - Refining: looking for new equilibriums: falling excess capacity and regional disparities, recovery in capital spending in emerging countries, Asia is still the eldorado for investment in the downstream oil Sector (Continuing overcapacity in the medium-term, Differing investment strategies)

National Offshore Wind Energy Grid Interconnection Study

Energy Technology Data Exchange (ETDEWEB)

Daniel, John P. [ABB Inc; Liu, Shu [ABB Inc; Ibanez, Eduardo [National Renewable Energy Laboratory; Pennock, Ken [AWS Truepower; Reed, Greg [University of Pittsburgh; Hanes, Spencer [Duke Energy

2014-07-30

The National Offshore Wind Energy Grid Interconnection Study (NOWEGIS) considers the availability and potential impacts of interconnecting large amounts of offshore wind energy into the transmission system of the lower 48 contiguous United States. A total of 54GW of offshore wind was assumed to be the target for the analyses conducted. A variety of issues are considered including: the anticipated staging of offshore wind; the offshore wind resource availability; offshore wind energy power production profiles; offshore wind variability; present and potential technologies for collection and delivery of offshore wind energy to the onshore grid; potential impacts to existing utility systems most likely to receive large amounts of offshore wind; and regulatory influences on offshore wind development. The technologies considered the reliability of various high-voltage ac (HVAC) and high-voltage dc (HVDC) technology options and configurations. The utility system impacts of GW-scale integration of offshore wind are considered from an operational steady-state perspective and from a regional and national production cost perspective.

Remote laser drilling and sampling system for the detection of concealed explosives

Science.gov (United States)

Wild, D.; Pschyklenk, L.; Theiß, C.; Holl, G.

2017-05-01

The detection of hazardous materials like explosives is a central issue in national security in the field of counterterrorism. One major task includes the development of new methods and sensor systems for the detection. Many existing remote or standoff methods like infrared or raman spectroscopy find their limits, if the hazardous material is concealed in an object. Imaging technologies using x-ray or terahertz radiation usually yield no information about the chemical content itself. However, the exact knowledge of the real threat potential of a suspicious object is crucial for disarming the device. A new approach deals with a laser drilling and sampling system for the use as verification detector for suspicious objects. Central part of the system is a miniaturised, diode pumped Nd:YAG laser oscillator-amplifier. The system allows drilling into most materials like metals, synthetics or textiles with bore hole diameters in the micron scale. During the drilling process, the hazardous material can be sampled for further investigation with suitable detection methods. In the reported work, laser induced breakdown spectroscopy (LIBS) is used to monitor the drilling process and to classify the drilled material. Also experiments were carried out to show the system's ability to not ignite even sensitive explosives like triacetone triperoxide (TATP). The detection of concealed hazardous material is shown for different explosives using liquid chromatography and ion mobility spectrometry.

Robotic Planetary Drill Tests

Science.gov (United States)

Glass, Brian J.; Thompson, S.; Paulsen, G.

2010-01-01

Several proposed or planned planetary science missions to Mars and other Solar System bodies over the next decade require subsurface access by drilling. This paper discusses the problems of remote robotic drilling, an automation and control architecture based loosely on observed human behaviors in drilling on Earth, and an overview of robotic drilling field test results using this architecture since 2005. Both rotary-drag and rotary-percussive drills are targeted. A hybrid diagnostic approach incorporates heuristics, model-based reasoning and vibration monitoring with neural nets. Ongoing work leads to flight-ready drilling software.

Offshore investments-cui prodis? Schrodinger's cat in offshore financing: Both alive and dead

Directory of Open Access Journals (Sweden)

Stepuk Anna

2014-01-01

Full Text Available Trends of FDI in offshore tax havens were compared to efforts and efficiency of regulatory authorities to prevent money laundering. Based on available data it was stated that current position in offshore FDI stays alive and officially dead at the same time, keeping the balance of interests for the main stakeholders: corporations, authorities and financial institutes support further offshore investments. Analysis based on volumes of trade and financial transactions between offshore centers, developed and developing countries. As a result withdrawal of financial resources from the developing countries degrades social capital funding and supports corruption growth.

Drilling contracts and incentives

International Nuclear Information System (INIS)

Osmundsen, Petter; Sorenes, Terje; Toft, Anders

2008-01-01

Shortages of rigs and personnel have encouraged discussion of designing incentive contracts in the drilling sector. However, for the drilling contracts, there are not a large variety of contract types in use. This article describes and analyses incentives for drilling contractors. These are directly represented by the compensation formats utilised in the present and in the consecutive drilling contracts. Indirectly, incentives are also provided by the evaluation criteria that oil companies use for awarding drilling assignments. Changes in contract format pose a number of relevant questions relating to resource management, and the article takes an in-depth look at some of these. Do evaluation criteria for awarding drilling assignments encourage the development of new technology and solutions? How will a stronger focus on drilling efficiency influence reservoir utilisation?

Offshore Resource Assessment and Design Conditions: A Data Requirements and Gaps Analysis for Offshore Renewable Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Elliott, Dennis [National Renewable Energy Lab. (NREL), Golden, CO (United States); Frame, Caitlin [National Oceanic and Atmospheric Administration (NOAA), Washington, DC (United States); Gill, Carrie [National Oceanic and Atmospheric Administration (NOAA), Washington, DC (United States); Hanson, Howard [Florida Atlantic Univ., Boca Raton, FL (United States); Moriarty, Patrick [National Renewable Energy Lab. (NREL), Golden, CO (United States); Powell, Mark [National Oceanic and Atmospheric Administration (NOAA), Washington, DC (United States); Shaw, William J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wilczak, Jim [National Oceanic and Atmospheric Administration (NOAA), Washington, DC (United States); Wynne, Jason [Energetics, Columbia, MD (United States)

2012-03-01

The offshore renewable energy industry requires accurate meteorological and oceanographic (“metocean”) data for evaluating the energy potential, economic viability, and engineering requirements of offshore renewable energy projects. It is generally recognized that currently available metocean data, instrumentation, and models are not adequate to meet all of the stakeholder needs on a national scale. Conducting wind and wave resource assessments and establishing load design conditions requires both interagency collaboration as well as valuable input from experts in industry and academia. Under the Department of Energy and Department of Interior Memorandum of Understanding, the Resource Assessment and Design Condition initiative supports collaborative national efforts by adding to core atmospheric and marine science knowledge relevant to offshore energy development. Such efforts include a more thorough understanding and data collection of key metocean phenomena such as wind velocity and shear; low-level jets; ocean, tidal, and current velocities; wave characteristics; geotechnical data relating to surface and subsurface characteristics; seasonal and diurnal variations; and the interaction among these conditions. Figure 1 presents a graphical representation of some metocean phenomena that can impact offshore energy systems. This document outlines the metocean observations currently available; those that are not available; and those that require additional temporal-spatial coverage, resolution, or processing for offshore energy in an effort to gather agreed-upon, needed observations.

Tesco's Bob Tessari: launching a drilling revolution

Energy Technology Data Exchange (ETDEWEB)

Budd, G.

2002-07-01

The 'Casing Drilling' technology, patented by Tesco, which allows operators to simultaneously drill, case and evaluate oil and gas wells, is described. The system is claimed to substantially reduce the amount of lost circulation, loss of well control and bore hole instability problems that have been documented to account for about 25 per cent of total rig time on a well, and at least $4 billion (or 10 per cent of the $40 billion annual global drilling tab) spent on 'unscheduled events' associated with tripping drill pipe. With the Casing Drilling process, wells are drilled using standard oilfield casing instead of drill pipe. The host of downhole problems associated with tripping in and out of the hole are avoided, as the casing pipe is never removed. Instead, drill bits and other downhole tools are tripped through the casing with wireline at a rate of about 500 ft per minute, drastically reducing tripping time. Tesco also developed the portable top drive, the manufacture and rental of which constitutes a large part of the company's business, besides helping technologically to make Casing Drilling possible. Much of the company's success is attributed to the tenacity and zest for innovative approaches of the company's CEO, Bob Tessari, who is largely responsible for the company finding itself at the centre of a drilling technology revolution.

Energetic aspects and opportunities for reusing water on offshore platforms in Campos Basin, Brazil

Directory of Open Access Journals (Sweden)

Victor Magalhães Duarte

2017-09-01

Full Text Available In the drilling and production of oil at sea, a large quantity of potable water used is most commonly transported to oil platforms using offshore supply vessels (OSVs. Sea water desalination is used as well, but only in a few oil platforms. To minimize energy consumption, water supply options were studied. The desalination of seawater and the reusing of streams of grey water and black water were evaluated and compared with the characteristics of the current supply via OSVs. In both desalination and OSV water supply options an electrolytic wastewater treatment plant is used. The objective of this study was to analyze the current situation regarding water supply on offshore platforms located in the Campos Basin, Rio de Janeiro, Brazil, and to propose measures to take advantage of opportunities to reuse water and reduce energy expenditure. Two alternative scenarios were developed that involved the reuse of water that comes from the effluent of a biological wastewater treatment plant (WWTP. Information on the logistics of supplying water to platforms was obtained through direct consultation with companies and sources in the literature. The results show that annual energy consumption (uptake, treatment, transportation, use and waste water treatment of water on offshore platforms is currently 1.89 GWh, and that a reduction of 1.8 GWh of the energy consumed can be achieved using advanced reuse treatments. Energy consumption in the water reuse treatment is more competitive than those of transport by OSVs or seawater desalination.

A Comparison of Pre-Test Means from Oil Field Workers Having Available Manuals and Those Lacking Manuals before Announced Training.

Science.gov (United States)

Zambon, Franco

A study assessed the validity of the hypothesis that offshore drilling personnel would independently study important material if they knew that they would eventually receive formal training on the topic covered in the material. Eighty-one crew members on an offshore drilling rig were randomly divided into experimental and control groups. Those in…

The Hans Tausen drill

DEFF Research Database (Denmark)

Johnsen, Sigfus Johann; Dahl-Jensen, Dorthe; Steffensen, Jørgen Peder

2007-01-01

In the mid-1990s, excellent results from the GRIP and GISP2 deep drilling projects in Greenland opened up funding for continued ice-coring efforts in Antarctica (EPICA) and Greenland (NorthGRIP). The Glaciology Group of the Niels Bohr Institute, University of Copenhagen, was assigned the task...... of providing drilling capability for these projects, as it had done for the GRIP project. The group decided to further simplify existing deep drill designs for better reliability and ease of handling. The drill design decided upon was successfully tested on Hans Tausen Ice Cap, Peary Land, Greenland, in 1995....... The 5.0 m long Hans Tausen (HT) drill was a prototype for the ~11 m long EPICA and NorthGRIP versions of the drill which were mechanically identical to the HT drill except for a much longer core barrel and chips chamber. These drills could deliver up to 4 m long ice cores after some design improvements...

WiFi RFID demonstration for resource tracking in a statewide disaster drill.