WorldWideScience

Sample records for 40-mhz annular array

  1. Limited Diffraction Maps for Pulsed Wave Annular Arrays

    Fox, Paul D.

    2002-01-01

    A procedure is provided for decomposing the linear field of flat pulsed wave annular arrays into an equivalent set of known limited diffraction Bessel beams. Each Bessel beam propagates with known characteristics, enabling good insight into the propagation of annular fields to be obtained....... Numerical examples are given in the context of a 10-ring annular array operating at a central frequency of 2.5 MHz in water....

  2. Limited Diffraction Maps for Pulsed Wave Annular Arrays

    Fox, Paul D.

    2002-01-01

    A procedure is provided for decomposing the linear field of flat pulsed wave annular arrays into an equivalent set of known limited diffraction Bessel beams. Each Bessel beam propagates with known characteristics, enabling good insight into the propagation of annular fields to be obtained. Numerical examples are given in the context of a 10-ring annular array operating at a central frequency of 2.5 MHz in water.

  3. Phased annular array transducers for ultrasonic guided wave applications

    Yan, Fei; Borigo, Cody; Liang, Yue; Koduru, Jaya P.; Rose, Joseph L.

    2011-04-01

    Mode and frequency control always plays an important role in ultrasonic guided wave applications. In this paper, theoretical understanding of guided wave excitations of axisymmetric sources on plate structures is established. It is shown that a wave number spectrum can be used to investigate the guided wave excitations of an axisymmetric source. The wave number spectrum is calculated from a Hankel transform of the axial source loading profile. On the basis of the theoretical understanding, phased annular array transducers are developed as a powerful tool for guided wave mode and frequency control. By applying appropriate time delays to phase the multiple elements of an annular array transducer, guided wave mode and frequency tuning can be achieved fully electronically. The phased annular array transducers have been successfully used for various applications. Example applications presented in this paper include phased annular arrays for guided wave beamforming and a novel ultrasonic vibration modal analysis technique for damage detection.

  4. Correspondence - Characterization of the effective performance of a high-frequency annular-array-based imaging system using anechoic-pipe phantoms.

    Filoux, Erwan; Mamou, Jonathan; Moran, Carmel M; Pye, Stephen D; Ketterling, Jeffrey A

    2012-12-01

    A resolution integral (RI) method based on anechoic- pipe, tissue-mimicking phantoms was used to compare the detection capabilities of high-frequency imaging systems based on a single-element transducer, a state-of-the-art 256-element linear array, or a 5-element annular array. All transducers had a central frequency of 40 MHz with similar conventionally measured axial and lateral resolutions (about 50 and 85 μm, respectively). Using the RI metric, the annular array achieved the highest performance (RI = 60), followed by the linear array (RI = 47), and the single-element transducer (RI = 24). Results showed that the RI metric could be used to efficiently quantify the effective transducer performance and compare the image quality of different systems.

  5. Radiation and reflection acoustical fields of an annular phased array

    LAI Puxiang; ZHANG Bixing; WANG Chenghao

    2007-01-01

    The characteristics of the radiation and reflection acoustical fields of an annular phased array are investigated. The effects of the element number, element radius, interelement spacing, centre frequency, focus position, and other parameters on the radiation acoustical field of the annular phased array is theoretically studied. In experiment, an annular transducer with 8 equal-area elements is designed and fabricated, and a series of experimental measurements are conducted. The radiation acoustical field and its reflection on a liquid-solid interface are theoretically and experimentally studied. The experimental result is in good agreement with the theoretical one.

  6. Guided Wave Annular Array Sensor Design for Improved Tomographic Imaging

    Koduru, Jaya Prakash; Rose, Joseph L.

    2009-03-01

    Guided wave tomography for structural health monitoring is fast emerging as a reliable tool for the detection and monitoring of hotspots in a structure, for any defects arising from corrosion, crack growth etc. To date guided wave tomography has been successfully tested on aircraft wings, pipes, pipe elbows, and weld joints. Structures practically deployed are subjected to harsh environments like exposure to rain, changes in temperature and humidity. A reliable tomography system should take into account these environmental factors to avoid false alarms. The lack of mode control with piezoceramic disk sensors makes it very sensitive to traces of water leading to false alarms. In this study we explore the design of annular array sensors to provide mode control for improved structural tomography, in particular, addressing the false alarm potential of water loading. Clearly defined actuation lines in the phase velocity dispersion curve space are calculated. A dominant in-plane displacement point is found to provide a solution to the water loading problem. The improvement in the tomographic images with the annular array sensors in the presence of water traces is clearly illustrated with a series of experiments. An annular array design philosophy for other problems in NDE/SHM is also discussed.

  7. Theoretical and Experimental Investigation of Ultrasonic Focusing with Annular Phased Array

    ZHANG Bi-Xing; WANG Cheng-Hao; LAI Pu-Xiang

    2006-01-01

    @@ The focused acoustic field generated by an annular array transducer and its reflection field on a solid-liquid interface are investigated theoretically and experimentally. Theoretically, the concise analytic expressions about the radiation and reflection acoustic fields of the annular phased array are obtained by the ray approach method (saddle-point method). In experiment, an annular transducer with 8 equal-area elements is designed and fabricated, and a series of experiments about the radiation acoustic field and its reflection on the liquid-solid interface are carried out. The experimental characteristics of the transducer are in good agreement with the numerical ones. It shows the correctness of the theoretical result and the feasibility of dynamic focusing of the experiment system. With the maximum amplitude and its emergence time of the reflection wave, we can acquire the information and the imaging of the reflection interface by the annular phased array dynamic focusing.

  8. A spacing compensation factor for the optimization of guided wave annular array transducers.

    Borigo, Cody; Rose, Joseph L; Yan, Fei

    2013-01-01

    Transducer arrays can be utilized in ultrasonic guided wave applications to achieve preferential excitation of particular points on a dispersion curve. These arrays are designed according to the principles of wave interference and the influence of the wavelength excitation spectrum. This paper develops the relationships between the peak wavelength in the excitation spectra and the element spacing of linear comb and annular arrays. The excitation spectra are developed by applying Fourier and Hankel transforms to the spatial loading distribution functions of the comb and annular arrays, respectively. Although the peak wavelength of excitation of a comb array is typically assumed to be equal to the element spacing, it is shown that this can be an inaccurate assumption for annular arrays. The ratio of element spacing to the peak wavelength in the excitation spectrum is termed the spacing compensation factor, and is dependent on the number of array elements and the inner radius. It is determined that the compensation factor is negligible for comb arrays but is crucial for annular arrays in order to achieve optimal mode selection. Finite element analyses and experimental data are used to verify the calculations and demonstrate the significance of the compensation factor.

  9. Time delay controlled annular array transducers for omnidirectional guided wave mode control in plate like structures

    Koduru, Jaya P.; Rose, Joseph L.

    2014-10-01

    Guided waves in plate like structures offer several modes with unique characteristics that can be taken advantage for nondestructive inspection applications. Conditions relating to the structure under inspection like the surrounding media, liquid loading, coatings etc require the use of special modes for successful inspection. Therefore, transducers that can excite mode controlled guided waves are essential for defect detection and discrimination in structures. Array transducers with annular elements can generate omnidirectional guided waves in plate like structures. However, the wave modes excited are limited to a particular wavelength governed by the element spacing. This limitation on the annular array transducers can be overcome by controlling the phase at each element relative to one another. In this work, annular array transducer construction techniques are theoretically examined and the optimum phase delays between the annular elements to excite a desired guided wave mode are calculated. A five element comb type annular array transducer is fabricated utilizing 1-3 type piezocomposite material. The mode control capability of the transducer is experimentally verified by selectively exciting the A0 and S0 guided wave modes in an aluminum plate like structure.

  10. Phased annular array transducers for omnidirectional guided wave mode control in isotropic plate like structures

    Koduru, Jaya P.; Momeni, Sepandarmaz; Rose, Joseph L.

    2013-12-01

    Ultrasonic guided waves are fast emerging as a reliable tool for continuous structural health monitoring. Their multi-modal nature along with their long range propagation characteristics offer several possibilities for interrogating structures. Transducers commonly used to generate guided waves in structures excite multiple modes at any frequency; their complex scattering and reflection from defects and boundaries often complicates the extraction of useful information. Often it is desirable to control the guided wave modes propagating in a structure to take advantage of their unique properties for different applications. Earlier attempts at guided wave mode control involved developing fixed wavelength linear and annular array transducers. Their only disadvantage is that the transducer is limited to a particular wavelength and a change in wavelength necessitates a change in the transducer. In this paper, we propose the development of an annular array transducer that can generate mode controlled omnidirectional guided waves by independently controlling the amplitude and phase of the array elements. A simplified actuator model that approximates the transducer loading on the structure to a constant pressure load under the array elements is assumed and an optimization problem is set up to compute the excitation voltage and phase of the elements. A five element annular array transducer is designed utilizing 1-3 type piezocomposite materials. The theoretical computations are experimentally verified on an aluminum plate like structure by exciting A0 and S0 guided wave modes.

  11. Analysis of annular phased array transducers for ultrasonic guided wave mode control

    Kannajosyula, H.; Lissenden, C. J.; Rose, J. L.

    2013-08-01

    Exact and asymptotic analyses of annular phased array transducers (PAT) for elastic guided wave mode selection are presented. For the purpose of analysis, the transducer-substrate interaction is formulated in terms of a three-dimensional analogy to filters as applied one-dimensionally in areas such as signal processing and control theory. This enables the deduction of most of the properties of the annular array purely from the Fourier analysis of any actuating function that represents the loading due to the transducer. A generalized mathematical model of the actuating function due to the annular PAT is constructed. The Fourier spectrum is analyzed for resonances in the wavenumber domain. Formulas for phase and time delays are presented. The phenomena of outgoing and incoming waves are also studied. Numerical analysis of the wavenumber spectrum for the annular PAT with a finite number of elements is performed to further illustrate the results deduced from exact and asymptotic analyses. Finite element simulations are presented to further verify the phenomena predicted through the wavenumber spectrum analysis.

  12. Fourier-Bessel Field Calculation and Tuning of a CW Annular Array

    Fox, Paul D.; Cheng, Jiqi; Lu, Jian-yu

    2002-01-01

    A 1-D Fourier-Bessel series method for computing and tuning the linear lossless field of flat continuous wave (CW) annular arrays is given and discussed with both numerical simulation and experimental verification. The technique provides a new method for modelling and manipulating the propagated...... field by linking the quantized surface pressure profile to a set of limited diffraction Bessel beams propagating into the medium. In the limit, these become a known set of nondiffracting Bessel beams satisfying the lossless linear wave equation, which allow us to derive a linear matrix formulation...... for the field in terms of the ring pressures on the transducer surface. Tuning (beamforming) of the field then follows by formulating a least squares design with respect to the transducer ring pressures. Results are presented in the context of a 10-ring annular array operating at 2.5 MHz in water....

  13. Self-assembled large-area annular cavity arrays with tunable cylindrical surface plasmons for sensing.

    Ni, Haibin; Wang, Ming; Shen, Tianyi; Zhou, Jing

    2015-02-24

    Surface plasmons that propagate along cylindrical metal/dielectric interfaces in annular apertures in metal films, called cylindrical surface plasmons (CSPs), exhibit attractive optical characteristics. However, it is challenging to fabricate these nanocoaxial structures. Here, we demonstrate a practical low-cost route to manufacture highly ordered, large-area annular cavity arrays (ACAs) that can support CSPs with great tunability. By employing a sol-gel coassembly method, reactive ion etching and metal sputtering techniques, regular, highly ordered ACAs in square-centimeter-scale with a gap width tunable in the range of several to hundreds of nanometers have been produced with good reproducibility. Ag ACAs with a gap width of 12 nm and a gap height of 635 nm are demonstrated. By finite-difference time-domain simulation, we confirm that the pronounced dips in the reflectance spectra of ACAs are attributable to CSP resonances excited in the annular gaps. By adjusting etching time and Ag film thickness, the CSP dips can be tuned to sweep the entire optical range of 360 to 1800 nm without changing sphere size, which makes them a promising candidate for forming integrated plasmonic sensing arrays. The high tunability of the CSP resonant frequencies together with strong electric field enhancement in the cavities make the ACAs promising candidates for surface plasmon sensors and SERS substrates, as, for example, they have been used in liquid refractive index (RI) sensing, demonstrating a sensitivity of 1505 nm/RIU and a figure of merit of 9. One of the CSP dips of ACAs with a certain geometry size is angle- (0-70 degrees) and polarization-independent and can be used as a narrow-band absorber. Furthermore, the nano annular cavity arrays can be used to construct solar cells, nanolasers and nanoparticle plasmonic tweezers.

  14. Micromachined high frequency PMN-PT/epoxy 1-3 composite ultrasonic annular array.

    Liu, Changgeng; Djuth, Frank; Li, Xiang; Chen, Ruimin; Zhou, Qifa; Shung, K Kirk

    2012-04-01

    This paper reports the design, fabrication, and performance of miniature micromachined high frequency PMN-PT/epoxy 1-3 composite ultrasonic annular arrays. The PMN-PT single crystal 1-3 composites were made with micromachining techniques. The area of a single crystal pillar was 9×9 μm. The width of the kerf among pillars was ∼5 μm and the kerfs were filled with a polymer. The composite thickness was 25 μm. A six-element annular transducer of equal element area of 0.2 mm(2) with 16 μm kerf widths between annuli was produced. The aperture size the array transducer is about 1.5 mm in diameter. A novel electrical interconnection strategy for high density array elements was implemented. After the transducer was attached to the electric connection board and packaged, the array transducer was tested in a pulse/echo arrangement, whereby the center frequency, bandwidth, two-way insertion loss (IL), and cross talk between adjacent elements were measured for each annulus. The center frequency was 50 MHz and -6 dB bandwidth was 90%. The average insertion loss was 19.5 dB at 50 MHz and the crosstalk between adjacent elements was about -35 dB. The micromachining techniques described in this paper are promising for the fabrication of other types of high frequency transducers, e.g. 1D and 2D arrays.

  15. Regional hyperthermia for deep-seated malignancies using the BSD annular array.

    Shimm, D S; Cetas, T C; Oleson, J R; Gross, E R; Buechler, D N; Fletcher, A M; Dean, S E

    1988-01-01

    Forty-four patients were treated using the BSD-1000 Annular Phased Array between April 1983 and December 1986. There were 32 pelvic, nine abdominal, two extremity, and one thoracic sites treated. Mean tumour volume was 646 cc. Thirty-nine patients had concurrent radiation therapy, receiving a mean dose of 38 Gy. Mean average temperature was 41.0 +/- 1.4 degrees C. Most patients experienced local or systemic toxicity, requiring temporary treatment interruption in 33 patients, and termination of treatment in eight. Chronic complications were seen in four, but these were in patients receiving high total radiation doses as well. There were six complete and five partial responses. Among the 32 patients with pelvic tumours, mean tumour volume was 317 cc, mean radiation dose was 42 Gy, and mean average temperature was 41.3 +/- 1.2 degrees C. There were five complete and four partial responses. Achieving tumour temperatures greater than or equal to 42 degrees C with the annular array is difficult, due to both systemic and local toxicity. To improve clinical hyperthermia for thoracic, abdominal, and pelvic tumours, new technologies such as steerable phased array microwave systems; scanned, focused ultrasound; and permanently implantable thermoregulating ferromagnetic seeds, or new approaches such as using drugs to alter blood flow, or combining hyperthermia with antineoplastic drugs or biological agents, will be necessary.

  16. A flexible annular-array imaging platform for micro-ultrasound.

    Qiu, Weibao; Yu, Yanyan; Chabok, Hamid Reza; Liu, Cheng; Tsang, Fu Keung; Zhou, Qifa; Shung, K Kirk; Zheng, Hairong; Sun, Lei

    2013-01-01

    Micro-ultrasound is an invaluable imaging tool for many clinical and preclinical applications requiring high resolution (approximately several tens of micrometers). Imaging systems for micro-ultrasound, including single-element imaging systems and linear-array imaging systems, have been developed extensively in recent years. Single-element systems are cheaper, but linear-array systems give much better image quality at a higher expense. Annular-array-based systems provide a third alternative, striking a balance between image quality and expense. This paper presents the development of a novel programmable and real-time annular-array imaging platform for micro-ultrasound. It supports multi-channel dynamic beamforming techniques for large-depth-of-field imaging. The major image processing algorithms were achieved by a novel field-programmable gate array technology for high speed and flexibility. Real-time imaging was achieved by fast processing algorithms and high-speed data transfer interface. The platform utilizes a printed circuit board scheme incorporating state-of-the-art electronics for compactness and cost effectiveness. Extensive tests including hardware, algorithms, wire phantom, and tissue mimicking phantom measurements were conducted to demonstrate good performance of the platform. The calculated contrast-to-noise ratio (CNR) of the tissue phantom measurements were higher than 1.2 in the range of 3.8 to 8.7 mm imaging depth. The platform supported more than 25 images per second for real-time image acquisition. The depth-of-field had about 2.5-fold improvement compared to single-element transducer imaging.

  17. Slanted annular aperture arrays as enhanced-transmission metamaterials: Excitation of the plasmonic transverse electromagnetic guided mode

    Ndao, Abdoulaye; Salut, Roland; Baida, Fadi I., E-mail: fbaida@univ-fcomte.fr [Département d' Optique P.M. Duffieux, Institut FEMTO-ST, UMR 6174 CNRS, Université de Franche–Comté, 25030 Besançon Cedex (France); Belkhir, Abderrahmane [Laboratoire de Physique et Chimie Quantique, Université Mouloud Mammeri, Tizi-Ouzou (Algeria)

    2013-11-18

    We present here the fabrication and the optical characterization of slanted annular aperture arrays engraved into silver film. An experimental enhanced transmission based on the excitation of the cutoff-less plasmonic guided mode of the nano-waveguides (the transmission electron microscopy mode) is demonstrated and agrees well with the theoretical predicted results. By the way, even if it is less efficient (70% → 20%), an enhanced transmission can occur at larger wavelength value (720 nm–930 nm) compared to conventional annular aperture arrays structure by correctly setting the metal thickness.

  18. Theory and experiment of Fourier-Bessel field calculation and tuning of a pulsed wave annular array

    Fox, Paul D.; Jiqi, Cheng; Jian-yu, Lu

    2003-01-01

    A one-dimensional (1D) Fourier-Bessel series method for computing and tuning (beamforming) the linear lossless field of flat pulsed wave annular arrays is developed and supported with both numerical simulation and experimental verification. The technique represents a new method for modeling....... Tuning of the field then also follows by formulating a least-squares design for the transducer surface pressure with respect to a given desired field in space and time. Simulated and experimental results for both field computation and tuning are presented in the context of a 10-ring annular array...

  19. Modeling of Focused Acoustic Field of a Concave Multi-annular Phased Array Using Spheroidal Beam Equation

    余立立; 寿文德; 惠春

    2012-01-01

    A theoretical model of focused acoustic field for a multi-annular phased array on concave spherical surface is proposed. In this model, the source boundary conditions of the spheroidal beam equation (SBE) for multi-annular phased elements are studied. Acoustic field calculated by the dynamic focusing model of SBE is compared with numerical results of the O'Neil and Khokhlov-Zabolotskaya-Kuznetsov (KZK) model, respectively. Axia/dynamic focusing and the harmonic effects are presented. The results demonstrate that the dynamic focusing model of SBE is good valid for a concave multi-annular phased array with a large aperture angle in the linear or nonlinear field.

  20. Reflective plasmonic waveplates based on metal-insulator-metal subwavelength rectangular annular arrays

    Chen, Zhonghui; Wang, Chinhua; Xu, Fuyang; Lou, Yimin; Cao, Bing; Li, Xiaofeng

    2014-04-01

    We propose and present a quarter-wave plate using metal-insulator-metal (MIM) structure with sub-wavelength rectangular annular arrays (RAA) patterned in the upper Au film. It is found that by manipulating asymmetric width of the annular gaps along two orthogonal directions, the reflected amplitude and phase of the two orthogonal components can be well controlled via the RAA metasurface tuned by the MIM cavity effect, in which the localized surface plasmon resonance dip can be flattened with the cavity length. A quarter-wave plate has been realized through an optimized design at 1.55 μm, in which the phase difference variation of less than 2% of the π/2 between the two orthogonal components can be obtained in an ultra-wide wavelength range of about 130 nm, and the reflectivity is up to ˜90% within the whole working wavelength band. It provides a great potential for applications in advanced nanophotonic devices and integrated photonic systems.

  1. An L-Band, Circularly Polarised, Dual-Feed, Cavity-Backed Annular Slot Antenna For Phased-Array Applications

    Larsen, Niels Vesterdal; Breinbjerg, Olav

    2006-01-01

    The results of a parametric study for the development of an L-band, circularly polarised, dual-feed, cavity-backed annular slot antenna is presented. The study included detailed numerical simulations and measurements on a prototype with different ground planes, to assess the antenna’s applicability...... as an element in a small phased array antenna....

  2. Fresnel phase retrieval method using an annular lens array on an SLM

    Loriot, V.; Mendoza-Yero, O.; Pérez-Vizcaíno, J.; Mínguez-Vega, G.; de Nalda, R.; Bañares, L.; Lancis, J.

    2014-10-01

    Wavefront aberrations play a major role when focusing an ultrashort laser pulse to a high-quality focal spot. Here, we report a novel method to measure and correct wavefront aberrations of a 30-fs pulsed laser beam. The method only requires a programmable liquid-crystal spatial light modulator and a camera. Wavefront retrieval is based on pupil segmentation with an annular lens array, which allows us to determine the local phase that minimizes focusing errors due to wavefront aberrations. Our method provides accurate results even when implemented with low dynamic range cameras and polychromatic beams. Finally, the retrieved phase is added to a diffractive lens codified onto the spatial light modulator to experimentally demonstrate near-diffraction-limited femtosecond beam focusing without refractive components.

  3. Annular phased array transducer for preclinical testing of anti-cancer drug efficacy on small animals.

    Kujawska, Tamara; Secomski, Wojciech; Byra, Michał; Postema, Michiel; Nowicki, Andrzej

    2017-04-01

    A technique using pulsed High Intensity Focused Ultrasound (HIFU) to destroy deep-seated solid tumors is a promising noninvasive therapeutic approach. A main purpose of this study was to design and test a HIFU transducer suitable for preclinical studies of efficacy of tested, anti-cancer drugs, activated by HIFU beams, in the treatment of a variety of solid tumors implanted to various organs of small animals at the depth of the order of 1-2cm under the skin. To allow focusing of the beam, generated by such transducer, within treated tissue at different depths, a spherical, 2-MHz, 29-mm diameter annular phased array transducer was designed and built. To prove its potential for preclinical studies on small animals, multiple thermal lesions were induced in a pork loin ex vivo by heating beams of the same: 6W, or 12W, or 18W acoustic power and 25mm, 30mm, and 35mm focal lengths. Time delay for each annulus was controlled electronically to provide beam focusing within tissue at the depths of 10mm, 15mm, and 20mm. The exposure time required to induce local necrosis was determined at different depths using thermocouples. Location and extent of thermal lesions determined from numerical simulations were compared with those measured using ultrasound and magnetic resonance imaging techniques and verified by a digital caliper after cutting the tested tissue samples. Quantitative analysis of the results showed that the location and extent of necrotic lesions on the magnetic resonance images are consistent with those predicted numerically and measured by caliper. The edges of lesions were clearly outlined although on ultrasound images they were fuzzy. This allows to conclude that the use of the transducer designed offers an effective noninvasive tool not only to induce local necrotic lesions within treated tissue without damaging the surrounding tissue structures but also to test various chemotherapeutics activated by the HIFU beams in preclinical studies on small animals.

  4. A 14-bit 40-MHz analog front end for CCD application

    Jingyu, Wang; Zhangming, Zhu; Shubin, Liu

    2016-06-01

    A 14-bit, 40-MHz analog front end (AFE) for CCD scanners is analyzed and designed. The proposed system incorporates a digitally controlled wideband variable gain amplifier (VGA) with nearly 42 dB gain range, a correlated double sampler (CDS) with programmable gain functionality, a 14-bit analog-to-digital converter and a programmable timing core. To achieve the maximum dynamic range, the VGA proposed here can linearly amplify the input signal in a gain range from -1.08 to 41.06 dB in 6.02 dB step with a constant bandwidth. A novel CDS takes image information out of noise, and further amplifies the signal accurately in a gain range from 0 to 18 dB in 0.035 dB step. A 14-bit ADC is adopted to quantify the analog signal with optimization in power and linearity. An internal timing core can provide flexible timing for CCD arrays, CDS and ADC. The proposed AFE was fabricated in SMIC 0.18 μm CMOS process. The whole circuit occupied an active area of 2.8 × 4.8 mm2 and consumed 360 mW. When the frequency of input signal is 6.069 MHz, and the sampling frequency is 40 MHz, the signal to noise and distortion (SNDR) is 70.3 dB, the effective number of bits is 11.39 bit. Project supported by the National Natural Science Foundation of China (Nos. 61234002, 61322405, 61306044, 61376033), the National High-Tech Program of China (No. 2013AA014103), and the Opening Project of Science and Technology on Reliability Physics and Application Technology of Electronic Component Laboratory (No. ZHD201302).

  5. Design of a portable noninvasive photoacoustic glucose monitoring system integrated laser diode excitation with annular array detection

    Zeng, Lvming; Liu, Guodong; Yang, Diwu; Ren, Zhong; Huang, Zhen

    2008-12-01

    A near-infrared photoacoustic glucose monitoring system, which is integrated dual-wavelength pulsed laser diode excitation with eight-element planar annular array detection technique, is designed and fabricated during this study. It has the characteristics of nonivasive, inexpensive, portable, accurate location, and high signal-to-noise ratio. In the system, the exciting source is based on two laser diodes with wavelengths of 905 nm and 1550 nm, respectively, with optical pulse energy of 20 μJ and 6 μJ. The laser beam is optically focused and jointly projected to a confocal point with a diameter of 0.7 mm approximately. A 7.5 MHz 8-element annular array transducer with a hollow structure is machined to capture photoacoustic signal in backward mode. The captured signals excitated from blood glucose are processed with a synthetic focusing algorithm to obtain high signal-to-noise ratio and accurate location over a range of axial detection depth. The custom-made transducer with equal area elements is coaxially collimated with the laser source to improve the photoacoustic excite/receive efficiency. In the paper, we introduce the photoacoustic theory, receive/process technique, and design method of the portable noninvasive photoacoustic glucose monitoring system, which can potentially be developed as a powerful diagnosis and treatment tool for diabetes mellitus.

  6. Performance evaluation of annular arrays in practice: The measurement of phase and amplitude patterns of radio-frequency deep body applicators

    Schneider, C.J.; Kuijer, J.P.A.; Colussi, L.C.; Schepp, C.J.; Dijk, J.D.P. van

    1995-01-01

    An approach to a solution of two major problems in operating Annular Phased Arrays in deep body hyperthermia is presented: an E-field sensor capable of measuring phase and amplitude at 70 MHz and the concept of a power transmission factor to determine the effective amplitude of each applicator. In t

  7. 环形狭缝腔阵列光学特性的研究∗%Finite difference time domain simulation of optical prop erties of annular cavity arrays

    周静; 王鸣; 倪海彬; 马鑫

    2015-01-01

    Optical properties of two-dimensional periodic annular cavity arrays in hexagonal packing are investigated by finite difference time domain simulation method in this paper. According to simulated reflectance/transmission spectra, electric field distribution and charge distribution, we confirm that multiple cylindrical surface plasmon resonances, which result in reflectance dips, can be excited in annular cavities by linearly polarized light. Mechanism of the cylindrical surface plasmons is investigated. A coaxial waveguide mode TE11 is excited in the annular cavities and a Fabry-Perot resonance is fulfilled along the depth direction of the annular cavities at the resonance wavelengths. While the number of reflectance dips and wavelengths of these dips in reflectance spectra are dependent on the geometric sizes of the annular cavities, the periodicity and polarization of incident light do not affect their reflectance spectra dramatically. Incident light beams with resonant wavelengths are localized in annular cavities with large electric field increasing and dissipate gradually due to metal loss. Reflectance dips can be tuned from 350 to 2000 nm by adjusting geometric size parameters of the annular cavities, such as outer and inner radii of the annular gaps, gap sizes and metal film thickness values. Reflectance dips shift toward longer wavelength with increasing inner and outer radii of the annular gaps, metal film thickness and with reducing the gap distance. In addition, infiltrate liquids in the annular gaps will result in a shift of the resonance wavelengths, which makes the annular cavities good refractive index sensors. A refractive index sensitivity up to 1850 nm/RIU is demonstrated. The refractive index sensitivities of annular cavities can also be tuned by their geometric sizes. Annular cavities with large electric field enhancement and tunable cylindrical surface plasmons can be used as surface enhanced Raman spectra substrates, refractive index sensors

  8. Highly Enriched Uranyl Nitrate in Annular Tanks with Concrete Reflection: 1 x 3 Line Array of Nested Pairs of Tanks

    James Cleaver; John D. Bess; Nathan Devine; Fitz Trumble

    2009-09-01

    A series of seven experiments were performed at the Rocky Flats Critical Mass Laboratory beginning in August, 1980 (References 1 and 2). Highly enriched uranyl nitrate solution was introduced into a 1-3 linear array of nested stainless steel annular tanks. The tanks were inside a concrete enclosure, with various moderator and absorber materials placed inside and/or between the tanks. These moderators and absorbers included boron-free concrete, borated concrete, borated plaster, and cadmium. Two configurations included placing bottles of highly enriched uranyl nitrate between tanks externally. Another experiment involved nested hemispheres of highly enriched uranium placed between tanks externally. These three configurations are not evaluated in this report. The experiments evaluated here are part of a series of experiments, one set of which is evaluated in HEU-SOL-THERM-033. The experiments in this and HEU-SOL-THERM-033 were performed similarly. They took place in the same room and used the same tanks, some of the same moderators and absorbers, some of the same reflector panels, and uranyl nitrate solution from the same location. There are probably additional similarities that existed that are not identified here. Thus, many of the descriptions in this report are either the same or similar to those in the HEU-SOL-THERM-033 report. Seventeen configurations (sixteen of which were critical) were performed during seven experiments; six of those experiments are evaluated here with thirteen configurations. Two configurations were identical, except for solution height, and were conducted to test repeatability. The solution heights were averaged and the two were evaluated as one configuration, which gives a total of twelve evaluated configurations. One of the seventeen configurations was subcritical. Of the twelve critical configurations evaluated, nine were judged as acceptable as benchmarks.

  9. The Characterization of the Radiation Acoustical Fields of an Annular Phased Array%相控环形阵辐射声场特性分析

    段文星; 乔文孝; 车小花

    2013-01-01

    Traditional down hole ultrasonovision and some down hole ultrasonic measurement techniques often use circular piston radiator,its focal length and direction are fixed,so it has the poor adaptability to different diameters and thicknesses of the cased holes.We simulate the radiation acoustical fields of the annular phased array in theory,and analyse the effects of the parameters of the annular phased array and the radiation acoustical fields on the focal length and direction.The above results show:①The array element in the array is designed as iso-area so that the radiation area of the array may be uniform distribution; ②The higher frequency in the array makes the radiation energy radiation along the axis line; ③Relative to the circular piston radiators,the annular phased array can achieve dynamic focusing by adjusting excitation signal phase of each unit,and it can be applied to the requirements of cased hole ultrasound imaging with different internal diametes.%传统的井下超声电视等井下超声测量技术中往往采用圆形活塞辐射器,其焦距和指向性同定,对于不同内径和厚度的套管井适应能力不好.理论模拟相控环形阵辐射器辐射声场的分布,分析相控环形阵辐射器各个参数对辐射声场的焦距和指向性的影响.相控环形阵辐射器阵元尺度的选择采用等面积方案有利于辐射面积在相控环形阵面内的均匀分布;使用相控阵时采用高频更利于辐射能量沿轴线集中辐射;相对于圆形活塞辐射器,相控环形阵辐射器可以在较低的频率下获得较小的焦斑直径,通过调整相位延迟获得不同的焦区范围,适应不同内径套管的超声成像测井要求.

  10. Simulation and performance of an artificial retina for 40 MHz track reconstruction

    Abba, A; Citterio, M; Caponio, F; Cusimano, A; Geraci, A; Marino, P; Morello, M J; Neri, N; Punzi, G.; Piucci, A; Ristori, L; Spinella, F; Stracka, S; Tonelli, D

    2015-01-01

    We present the results of a detailed simulation of the artificial retina pattern-recognition algorithm, designed to reconstruct events with hundreds of charged-particle tracks in pixel and silicon detectors at LHCb with LHC crossing frequency of 40MHz. The detailed geometry and charged-particle activity of a large tracking detector are simulated and used to assess the performance of the artificial retina algorithm. Excellent performances have been found for the retina pattern-recognition algorithm, comparable with the full LHCb reconstruction algorithm.

  11. A 40 MHz Trigger-free Readout Architecture for the LHCb experiment at CERN

    Alessio, F; Guzik, Z

    2009-01-01

    LHCb is considering an upgrade towards a full 40 MHz readout. In this paper we investigate possibilities for a new Timing and Fast Control (TFC) system based on completely new technologies, and the consequences for the readout electronics. We define the requirements and propose an architecture allowing partitioning, complete readout control and event management. The backbone is based on bidirectional high-speed optical links using the latest FPGA transceivers. For the Front-End Electronics we advocate exploiting the bidirectional capability of the CERN GigaBit Transceiver to make the Readout Boards the TFC and the Control System interface to the Front-End

  12. Annular-force-based variable curvature mirror combined with multi-point actuation array to improve the surface figure accuracy: a prototype design

    Zhao, Hui; Xie, Xiaopeng; Ren, Guorui; Du, Yunfei; Liu, Meiying; Wei, Jingxuan

    2016-10-01

    In recent years, a novel optical zooming technique has been paid much attention. With the help of optical leveraging effect, it is possible to alter the system focal length dramatically without moving elements involved in by only changing the curvature radius of VCM (variable curvature mirror) slightly. With no doubt, VCM is the key to realize non-moving element optical zooming and it has to provide large enough saggitus variation while still maintaining the high surface figure accuracy to ensure high quality imaging. In our previously published paper, an annular force based VCM has been designed, fabricated and tested. Experiments demonstrate that with the aperture of 100mm and thickness of 2mm, the VCM could generate a large saggitus variation exceeding 30λ (λ=632.8nm). However, the optical quality degrades very fast and this makes such a VCM unsuitable for optical imaging in visible band. Therefore in this manuscript, a multipoint actuation array, which is composed of totally 49 piezoelectric actuators, is embedded into the annular structure to aim to correct the surface figure distortion caused by large saggitus variation. The new structure model has been designed and numerical simulation indicates that the surface figure distortion could be well corrected as long as the degraded surface figure accuracy is better than 1.8λ (λ=632.8nm) (RMS). Based on this, a new prototype VCM is being fabricated and intermediate results are reported here.

  13. Hyperthermic therapy of deep seated tumors: comparison of the heating efficiencies of an annular array applicator and a capacitively coupled radiofrequency system.

    Egawa, S; Tsukiyama, I; Akine, Y; Kajiura, Y; Ogino, T; Yamashita, K

    1988-03-01

    Among 82 cases of deep seated tumors treated by hyperthermia with an annular array applicator (AA) and/or a capacitively coupled 8 mHz system (CCS) combined with radiation therapy, 13 cases were treated by both devices. The efficiencies of tumor heating were compared in terms of the time required to attain 42 degrees C, the duration of heating time and the thermal dose as determined by a biological iso-effect formula for equivalent minutes at 42.5 degrees C. Temperature profiles and percent of temperature levels greater than 42 degrees C were better in the cases treated by the AA, but higher thermal doses were obtained with the CCS because longer treatment times were tolerated with the CCS than with the AA. Methods are necessary to prevent excess elevation of body temperature in the case of the AA, and to reduce superficial pain where the applicators contact the skin in the case of the CCS.

  14. Advantage of annular focus generation by sector-vortex array in cavitation-enhanced high-intensity focused ultrasound treatment

    Jimbo, Hayato; Takagi, Ryo; Taguchi, Kei; Yoshizawa, Shin; Umemura, Shin-ichiro

    2016-07-01

    High-intensity focused ultrasound (HIFU) is a noninvasive method for cancer treatment. One of the disadvantages of this method is that it has a long total treatment time because of the smallness of the treatment volume by a single exposure. To solve this problem, we have proposed a method of cavitation-enhanced heating, which utilized the heat generated by oscillating the cavitation bubbles, in combination with the method of lateral enlargement of a HIFU focal zone to minimize the surface volume ratio. In a previous study, focal spot scanning at multiple points was employed for the enlargement. This method involves nonlinear propagation and absorption due to the high spatial-peak temporal-peak (SPTP) intensity in addition to the cavitation-enhanced heating. However, it is difficult to predict the size and position of the coagulation volume because they are significantly affected by the nonlinear parameters of the tissue. In this study, a sector vortex method was employed to directly synthesize an annular focal pattern. Since this method can keep the SPTP intensity at a manageably low level, nonlinear propagation and absorption can be minimized. Experimental results demonstrate that the coagulation was generated only in the region where both the cavitation cloud and the heating ultrasound were matched. The proposed method will make the cavitation-enhanced HIFU treatment more accurate and predictable.

  15. Numerical simulations of annular wire-array z-pinches in (x,y), (r,{theta}), and (r,z) geometries

    Marder, B.M.; Sanford, T.W.L.; Allshouse, G.O.

    1997-12-01

    The Total Immersion PIC (TIP) code has been used in several two-dimensional geometries to understand better the measured dynamics of annular, aluminum wire-array z-pinches. The areas investigated include the formation of the plasma sheath from current-induced individual wire explosions, the effects of wire number and symmetry on the implosion dynamics, and the dependence of the Rayleigh-Taylor instability growth on initial sheath thickness. A qualitative change in the dynamics with increasing wire number was observed, corresponding to a transition between a z-pinch composed of non-merging, self-pinching individual wires, and one characterized by the rapid formation and subsequent implosion of a continuous plasma sheath. A sharp increase in radiated power with increasing wire number has been observed experimentally near this calculated transition. Although two-dimensional codes have correctly simulated observed power pulse durations, there are indications that three dimensional effects are important in understanding the actual mechanism by which these pulse lengths are produced.

  16. Enhancement of magneto-optical Faraday effects and extraordinary optical transmission in a tri-layer structure with rectangular annular arrays.

    Lei, Chengxin; Chen, Leyi; Tang, Zhixiong; Li, Daoyong; Cheng, Zhenzhi; Tang, Shaolong; Du, Youwei

    2016-02-15

    The properties of optics and magneto-optical Faraday effects in a metal-dielectric tri-layer structure with subwavelength rectangular annular arrays are investigated. It is noteworthy that we obtained the strongly enhanced Faraday rotation of the desired sign along with high transmittance by optimizing the parameters of the nanostructure in the visible spectral ranges. In this system, we obtained two extraordinary optical transmission (EOT) resonant peaks with enhanced Faraday rotations, whose signs are opposite, which may provide the possibility of designing multi-channel magneto-optical devices. Study results show that the maximum of the figure of merit (FOM) of the structure can be obtained between two EOT resonant peaks accompanied by an enhanced Faraday rotation. The positions of the maximum value of the FOM and resonant peaks of transmission along with a large Faraday rotation can be tailored by simply adjusting the geometric parameters of our models. These research findings are of great importance for future applications of magneto-optical devices.

  17. The 40 MHz trigger-less DAQ for the LHCb Upgrade

    Campora Perez, D. H.; Falabella, A.; Galli, D.; Giacomini, F.; Gligorov, V.; Manzali, M.; Marconi, U.; Neufeld, N.; Otto, A.; Pisani, F.; Vagnoni, V. M.

    2016-07-01

    The LHCb experiment will undergo a major upgrade during the second long shutdown (2018-2019), aiming to let LHCb collect an order of magnitude more data with respect to Run 1 and Run 2. The maximum readout rate of 1 MHz is the main limitation of the present LHCb trigger. The upgraded detector, apart from major detector upgrades, foresees a full read-out, running at the LHC bunch crossing frequency of 40 MHz, using an entirely software based trigger. A new high-throughput PCIe Generation 3 based read-out board, named PCIe40, has been designed for this purpose. The read-out board will allow an efficient and cost-effective implementation of the DAQ system by means of high-speed PC networks. The network-based DAQ system reads data fragments, performs the event building, and transports events to the High-Level Trigger at an estimated aggregate rate of about 32 Tbit/s. Different architecture for the DAQ can be implemented, such as push, pull and traffic shaping with barrel-shifter. Possible technology candidates for the foreseen event-builder under study are InfiniBand and Gigabit Ethernet. In order to define the best implementation of the event-builder we are performing tests of the event-builder on different platforms with different technologies. For testing we are using an event-builder evaluator, which consists of a flexible software implementation, to be used on small size test beds as well as on HPC scale facilities. The architecture of DAQ system and up to date performance results will be presented.

  18. The 40 MHz trigger-less DAQ for the LHCb Upgrade

    Campora Perez, D.H. [INFN CNAF, Bologna (Italy); Falabella, A., E-mail: antonio.falabella@cnaf.infn.it [CERN, Geneva (Switzerland); Galli, D. [INFN Sezione di Bologna, Bologna (Italy); Università Bologna, Bologna (Italy); Giacomini, F. [CERN, Geneva (Switzerland); Gligorov, V. [INFN CNAF, Bologna (Italy); Manzali, M. [Università Bologna, Bologna (Italy); Università Ferrara, Ferrara (Italy); Marconi, U. [INFN Sezione di Bologna, Bologna (Italy); Neufeld, N.; Otto, A. [INFN CNAF, Bologna (Italy); Pisani, F. [INFN CNAF, Bologna (Italy); Università la Sapienza, Roma (Italy); Vagnoni, V.M. [INFN Sezione di Bologna, Bologna (Italy)

    2016-07-11

    The LHCb experiment will undergo a major upgrade during the second long shutdown (2018–2019), aiming to let LHCb collect an order of magnitude more data with respect to Run 1 and Run 2. The maximum readout rate of 1 MHz is the main limitation of the present LHCb trigger. The upgraded detector, apart from major detector upgrades, foresees a full read-out, running at the LHC bunch crossing frequency of 40 MHz, using an entirely software based trigger. A new high-throughput PCIe Generation 3 based read-out board, named PCIe40, has been designed for this purpose. The read-out board will allow an efficient and cost-effective implementation of the DAQ system by means of high-speed PC networks. The network-based DAQ system reads data fragments, performs the event building, and transports events to the High-Level Trigger at an estimated aggregate rate of about 32 Tbit/s. Different architecture for the DAQ can be implemented, such as push, pull and traffic shaping with barrel-shifter. Possible technology candidates for the foreseen event-builder under study are InfiniBand and Gigabit Ethernet. In order to define the best implementation of the event-builder we are performing tests of the event-builder on different platforms with different technologies. For testing we are using an event-builder evaluator, which consists of a flexible software implementation, to be used on small size test beds as well as on HPC scale facilities. The architecture of DAQ system and up to date performance results will be presented.

  19. Performance of a double metal n-on-n and a Czochralski silicon strip detector read out at 40 MHz

    Palacios, J P; Buytaert, J; Collins, P; Eckstein, D; Harkonen, J; Tuovinen, E; Luukka, P

    2006-01-01

    The R&D undertaken by the VELO group in order to produce a sensor that satisfies the tight radiation hardness, efficiency, resolution and low material requirements of LHCb has resulted in the choice of an n-on-n double metal layer solution. First measurements of the performance of the latest prototype and its related front end electronics, designed to function at the LHC speed of 40 MHz, are presented here. In addition, research has been carried out into new materials which could retain good performance in high radiation environments at and beyond the LHC, and could provide an alternative for a possible VELO upgrade. For the first time a full size Czochralski silicon detector sample with 50$\\mu$m pitch strips has been irradiated with high energy protons and its performance has been measured in a test beam with 40 MHz electronics. The results of this test will be presented.

  20. The readout of the LHC beam luminosity monitor: accurate shower energy measurements at a 40 MHz repetition rate

    Manfredi, P.F. E-mail: pfmanfredi@lbl.gov; Ratti, L.; Speziali, V.; Traversi, G.; Manghisoni, M.; Re, V.; Denes, P.; Placidi, M.; Ratti, A.; Turner, W.C.; Datte, P.S.; Millaud, J.E

    2004-02-01

    The LHC beam luminosity monitor is based on the following principle. The neutrals that originate in LHC at every PP interaction develop showers of minimum ionizing particles in the absorbers placed in front of the separation dipoles. The shower energy, measured by suitable detectors in the absorbers is proportional to the number of neutral particles and, therefore, to the luminosity. The principle lends itself to a luminosity measurement on a bunch-by-bunch basis. However, to make such a measurement feasible, the system must comply with extremely stringent requirements. Its speed of operation must match the 40 MHz bunch repetition rate of LHC. Besides, the detector must stand extremely high radiation doses. This paper discusses the solutions adopted to comply with these requirements.

  1. The readout of the LHC beam luminosity monitor Accurate shower energy measurements at a 40 MHz repetition rate

    Manfredi, P F; Speziali, V; Traversi, G; Manghisoni, M; Re, V; Denes, P; Placidi, Massimo; Ratti, A; Turner, W C; Datte, P S; Millaud, J E

    2004-01-01

    The LHC beam luminosity monitor is based on the following principle. The neutrals that originate in LHC at every PP interaction develop showers of minimum ionizing particles in the absorbers placed in front of the separation dipoles. The shower energy, measured by suitable detectors in the absorbers is proportional to the number of neutral particles and, therefore, to the luminosity. The principle lends itself to a luminosity measurement on a bunch-by-bunch basis. However, to make such a measurement feasible, the system must comply with extremely stringent requirements. Its speed of operation must match the 40 MHz bunch repetition rate of LHC. Besides, the detector must stand extremely high radiation doses. This paper discusses the solutions adopted to comply with these requirements.

  2. Subcutaneous granuloma annulare

    Dhar Sandipan

    1994-01-01

    Full Text Available Two cases of subcutaneos granuloma annulare are reported. Clinical presentation was in the form of hard subcutaneous nodules; histopathology confirmed the clinical diagnosis. The cases were unique because of onset in adult hood, occurrence over unusual sites and absence of classical lesions of granuloma annulare elsewhere.

  3. Subcutaneous granuloma annulare

    Dhar Sandipan

    1993-01-01

    Full Text Available Two cases of subcutaneous granuloma annulare are reported. Clinical presentation was in the form of hard subcutaneous nodules, histopathology confirmed the clinical diagnosis. The cases were unique because of onset in adult age, occurrence over unusual sites and absence of classical lesions of granuloma annulare elsewhere.

  4. Annular pancreas (image)

    Annular pancreas is an abnormal ring or collar of pancreatic tissue that encircles the duodenum (the part of the ... intestine that connects to stomach). This portion of pancreas can constrict the duodenum and block or impair ...

  5. Generalized granuloma annulare

    Khatri M

    1995-01-01

    Full Text Available A 35-years-old female patient had generalized pruritic papular lesions, distributed like dermatitis herpetiformis for last 4 years. Histopathologic changes were typical of granuloma annulare with negative results of direct immunofluorescence. The patient did not have association of diabetes mellitus or any other systemic disease. She failed to respond to dapsone therapy and 13-cis-retinoic acid.

  6. Gain-switched laser diode seeded Yb-doped fiber amplifier delivering 11-ps pulses at repetition rates up to 40-MHz

    Ryser, Manuel; Pilz, Soenke; Burn, Andreas; Romano, Valerio

    2014-01-01

    Here, we demonstrate all-fiber direct amplification of 11 picosecond pulses from a gain-switched laser diode at 1063nm. The diode was driven at a repetition rate of 40MHz and delivered 13$\\mu$W of fiber-coupled average output power. For the low output pulse energy of 0.33pJ we have designed a multi-stage core pumped preamplifier based on single clad Yb-doped fibers in order to keep the contribution of undesired amplified spontaneous emission as low as possible and to minimize temporal and spectral broadening. After the preamplifier we reduced the 40MHz repetition rate to 1MHz using a fiber coupled pulse-picker. The final amplification was done with a cladding pumped Yb-doped large mode area fiber and a subsequent Yb-doped rod-type fiber. With our setup we achieved amplification of 72dBs to an output pulse energy of 5.7$\\mu$J, pulse duration of 11ps and peak power of >0.6MW.

  7. Annular recuperator design

    Kang, Yungmo

    2005-10-04

    An annular heat recuperator is formed with alternating hot and cold cells to separate counter-flowing hot and cold fluid streams. Each cold cell has a fluid inlet formed in the inner diameter of the recuperator near one axial end, and a fluid outlet formed in the outer diameter of the recuperator near the other axial end to evenly distribute fluid mass flow throughout the cell. Cold cells may be joined with the outlet of one cell fluidly connected to the inlet of an adjacent downstream cell to form multi-stage cells.

  8. [Disseminated granuloma annulare].

    Kansky, A

    1975-09-01

    A case of generalized granuloma annulare in a 55 year old man is reported. The disease appeared five years before the first admission to the hospital. A large number of bluish-red or skin-colour papules were scattered mainly around the earlobes, buttocks and on the extremities. Some of the lesions were lined up in rings or plaques. Small depigmented and brownish scars were present. Two biopsies revealed characteristic foci of complete collagen degeneration accompanied by a palisading infiltrate in the upper dermis. Treatment with tuberculostatics and antimalarics was without improvement. The lesions cleared after a course of prednison, but reappeared when the drug was discontinued.

  9. Multiple annular linear diffractive axicons.

    Bialic, Emilie; de la Tocnaye, Jean-Louis de Bougrenet

    2011-04-01

    We propose a chromatic analysis of multiple annular linear diffractive axicons. Large aperture axicons are optical devices providing achromatic nondiffracting beams, with an extended depth of focus, when illuminated by a white light source, due to chromatic foci superimposition. Annular apertures introduce chromatic foci separation, and because chromatic aberrations result in focal segment axial shifts, polychromatic imaging properties are partially lost. We investigate here various design parameters that can be used to achieve color splitting, filtering, and combining using these properties. In order to improve the low-power efficiency of a single annular axicon, we suggest a spatial multiplexing of concentric annular axicons with different sizes and periods we call multiple annular aperture diffractive axicons (MALDAs). These are chosen to maintain focal depths while enabling color imaging with sufficient diffraction efficiency. Illustrations are given for binary phase diffractive axicons, considering technical aspects such as grating design wavelength and phase dependence due to the grating thickness.

  10. Polarization-independent waveguiding with annular photonic crystals.

    Cicek, Ahmet; Ulug, Bulent

    2009-09-28

    A linear waveguide in an annular photonic crystal composed of a square array of annular dielectric rods in air is demonstrated to guide transverse electric and transverse magnetic modes simultaneously. Overlapping of the guided bands in the full band gap of the photonic crystal is shown to be achieved through an appropriate set of geometric parameters. Results of Finite-Difference Time-Domain simulations to demonstrate polarization-independent waveguiding with low loss and wavelength-order confinement are presented. Transmission through a 90 degrees bend is also demonstrated.

  11. Annular Hybrid Rocket Motor Project

    National Aeronautics and Space Administration — Engineers at SpaceDev have conducted a preliminary design and analysis of a proprietary annular design concept for a hybrid motor. A U.S. Patent application has been...

  12. Annular Elastolytic Giant Cell Granuloma

    Khandpur Sujay

    2001-01-01

    Full Text Available The clinical and histopathological features of annular elastolytic giant cell granuloma in a 42â€"year-old female patient are described. The condition presented as annular erythematous plaques over sun- exposed skin sparing the face. Histopathology revealed dense granulomatous infiltrate consisting of numerous giant cells and lymphohistiocytes without any palisading arrangement or necrobiosis. The features differentiating it from other similar granulomatous disorders are discussed.

  13. Manufacture of annular cermet articles

    Forsberg, Charles W.; Sikka, Vinod K.

    2004-11-02

    A method to produce annular-shaped, metal-clad cermet components directly produces the form and avoids multiple fabrication steps such as rolling and welding. The method includes the steps of: providing an annular hollow form with inner and outer side walls; filling the form with a particulate mixture of ceramic and metal; closing, evacuating, and hermetically sealing the form; heating the form to an appropriate temperature; and applying force to consolidate the particulate mixture into solid cermet.

  14. Annular lipoatrophy of the ankles.

    Dimson, Otobia G; Esterly, Nancy B

    2006-02-01

    Lipoatrophic panniculitis likely represents a group of disorders characterized by an inflammatory panniculitis followed by lipoatrophy. It occurs locally in a variety of settings and has been reported in the literature under various terms, including annular atrophic connective tissue panniculitis of the ankles, annular and semicircular lipoatrophy, abdominal lipoatrophy, and connective tissue panniculitis. Herein, a case of annular lipoatrophy of the ankles is described in a 6-year-old girl with autoimmune thyroid disease. Histologically, a mixed lobular panniculitis with lipophages was present. This pattern resembles that seen in lipoatrophic panniculitis. After a single, acute episode of an inflammatory process with subsequent lipoatrophy, her skin lesions have stabilized for 2 years requiring no treatment.

  15. Eosinophilic annular erythema in childhood - Case report*

    Abarzúa, Alvaro; Giesen, Laura; Silva, Sergio; González, Sergio

    2016-01-01

    Eosinophilic annular erythema is a rare, benign, recurrent disease, clinically characterized by persistent, annular, erythematous lesions, revealing histopathologically perivascular infiltrates with abundant eosinophils. This report describes an unusual case of eosinophilic annular erythema in a 3-year-old female, requiring sustained doses of hydroxychloroquine to be adequately controlled. PMID:27579748

  16. Benign concentric annular macular dystrophy

    Luísa Salles de Moura Mendonça

    2015-06-01

    Full Text Available The purpose of the authors is to show clinical findings of a patient with benign concentric annular macular dystrophy, which is an unusual condition, and part of the "bull’s eye" maculopathy differential diagnosis. An ophthalmologic examination with color perception, fluorescein angiography, and ocular electrophysiology was performed.

  17. A Reconfigurable Radiation Pattern Annular Slot Antenna

    Aziz, NA; Radhi, A; Nilavalan, R

    2016-01-01

    This paper contemplate a theoretical analysis of a pattern reconfigurable antenna using annular slot antenna operating in low frequency. A shorting pin is inserted to allow the annular slot antenna to have an omnidirectional radiation pattern like a monopole antenna. The reconfigurable antenna consists of numerous metal cylinders arranged around the annular slot antenna. By controlling pin diodes associated with the metal cylinders, the antenna is capable of working up in different dire...

  18. Vibration of an eccentrically clamped annular plate

    Tseng, J.-G.; Wickert, J. A.

    1994-04-01

    Small amplitude vibration of an eccentric annular plate, which is free along its outer edge and clamped along the interior, is investigated through experimental and analytical methods. A disk with this geometry, or a stacked array in which the clamping and symmetry axes of each disk are nominally coincident, is common in data storage and brake systems applications. In the present case, the geometric imperfections on the boundary can have important implications for the disk's dynamic response. Changes that occur in the natural frequency spectrum, the mode shapes, and the free response under eccentric mounting are studied through laboratory measurements and an approximate discrete model of the plate. The natural frequencies and modes are found through global discretization of the Kamke quotient for a classical thin plate. For the axisymmetric geometry, the natural frequencies of the sine and cosine vibration modes for a specified number of nodal diameters are repeated. With increasing eccentricity, on the other hand, each pair of repeated frequencies splits at a rate that depends on the number of nodal diameters. Over a range of clamping and eccentricity ratios, the model's predictions are compared to the measured results.

  19. Non-integral dimensions ultrasonic phased arrays in a borehole

    ZHANG Bixing; ZHANG Chengguang; Deng Fangqing

    2009-01-01

    The non-integral dimensions ultrasonic phased arrays and their scanning and test-ing methods in a borehole are studied. First, the focusing acoustic fields excited by the 1.25D, 1.5D, and 1.75D phased arrays are analyzed, and then the imaging resolution in the elevation direction and the influence of the dynamic elements are investigated. Second, the focusing and deflexion characteristics of the acoustic fields excited by the annular and segmented annular phased arrays are studied, and they are compared with those excited by the 2D surface array. The application method of the 1.25D, 1.5D, and 1.75D, annular and segmented annular phased arrays in acoustic logging are analyzed and discussed. It provides a theoretical foundation for the application of the ultrasonic phased arrays in acoustic logging.

  20. Confocal Annular Josephson Tunnel Junctions

    Monaco, Roberto

    2016-09-01

    The physics of Josephson tunnel junctions drastically depends on their geometrical configurations and here we show that also tiny geometrical details play a determinant role. More specifically, we develop the theory of short and long annular Josephson tunnel junctions delimited by two confocal ellipses. The behavior of a circular annular Josephson tunnel junction is then seen to be simply a special case of the above result. For junctions having a normalized perimeter less than one, the threshold curves in the presence of an in-plane magnetic field of arbitrary orientations are derived and computed even in the case with trapped Josephson vortices. For longer junctions, a numerical analysis is carried out after the derivation of the appropriate motion equation for the Josephson phase. We found that the system is modeled by a modified and perturbed sine-Gordon equation with a space-dependent effective Josephson penetration length inversely proportional to the local junction width. Both the fluxon statics and dynamics are deeply affected by the non-uniform annulus width. Static zero-field multiple-fluxon solutions exist even in the presence of a large bias current. The tangential velocity of a traveling fluxon is not determined by the balance between the driving and drag forces due to the dissipative losses. Furthermore, the fluxon motion is characterized by a strong radial inward acceleration which causes electromagnetic radiation concentrated at the ellipse equatorial points.

  1. Soliton bunching in annular Josephson junctions

    Vernik, I.V; Lazarides, Nickos; Sørensen, Mads Peter

    1996-01-01

    By studying soliton (fluxon) motion in long annular Josephson junctions it is possible to avoid the influence of the boundaries and soliton-soliton collisions present in linear junctions. A new experimental design consisting of a niobium coil placed on top of an annular junction has been used...

  2. Optimum annular focusing by a phase plate

    Arrizón, Victor; Aguirre-Olivas, Dilia; Mellado-Villaseñor, Gabriel

    2015-01-01

    Conventional light focusing, i. e. concentration of an extended optical field within a small area around a point, is a frequently used process in Optics. An important extension to conventional focusing is the generation of the annular focal field of an optical beam. We discuss a simple optical setup that achieves this kind of focusing employing a phase plate as unique optical component. We first establish the class of beams that being transmitted through the phase plate can be focused into an annular field with topological charge of arbitrary integer order q. Then, for each beam in this class we determine the plate transmittance that generates the focal field with the maximum possible peak intensity. In particular, we discuss and implement experimentally the optimum annular focusing of a Gaussian beam. The attributes of optimum annular focal fields, namely the high peak intensity, intensity gradient and narrow annular section, are advantageous for different applications of such structured fields.

  3. [Generalized granuloma annulare or diffuse dermal histiocytosis?].

    Kretzschmar, L; Biel, K; Luger, T A; Goerdt, S

    1995-08-01

    Generalized granuloma annulare is a rare variant of granuloma annulare affecting the trunk and extremities with a multitude of lesions. In contrast to localized granuloma annulare, generalized granuloma annulare occurs in older patients, shows a stronger association with diabetes, and is characteristically chronic. Like our 55-year-old patient, most patients present with papules and annular plaques; less often, macular or non-annular lesions may be encountered. Histology often fails to show necrobiotic or necrotic connective tissue changes demarcated by a palisading granuloma. Instead, there are diffuse dermal, band-like or nodular aggregations of histiocytes intermingled with some multinucleated giant cells and a predominantly lymphocytic infiltrate in the periphery. Because of its special characteristics, it has been suggested that generalized granuloma annulare might constitute a separate disease entity and that it should be classed among the primary cutaneous histiocytoses as a diffuse dermal histiocytosis. Using immunohistochemistry to determine the macrophage phenotype of the lesional histiocytes, we have shown that generalized granuloma annulare is not a cutaneous histiocytosis. Neither MS-1 high-molecular-weight protein, a new specific marker for cutaneous non-Langerhans cell histiocytoses, nor CD1a, the well-known marker for Langerhans cells and Langerhans cell histiocytoses, is expressed by the lesional histiocytes of our patient. In contrast, the antigen expression pattern was diagnostic for non-infectious granulomas and was highly similar to that in localized granuloma annulare. In contrast to the successful treatment of localized granuloma annulare reported with intralesional interferon beta-1, systemic treatment with interferon alpha-2b (9 x 10(6) units three times a week) was ineffective.

  4. A clinical study of annular cyclitis

    Marilita Michael Moschos

    2009-02-01

    Full Text Available Marilita Michael Moschos1, Yan Guex-Crosier2, Ioannis Margetis1, Leonidas Zografos21Department of Ophthalmology, University of Athens, Greece; 2Jules Gonin Eye Hospital, University of Lausanne, SwitzerlandPurpose: To investigate six cases of annular cyclitis.Methods: All patients with impairment of visual acuity underwent complete ophthalmologic examination, color fundus photography, laboratory tests and fluorescein angiography. Indocyanine green (ICG angiography and B-scan ultrasonography were also performed in three cases in order to diagnose the disease.Results: All patients presented a unilateral or bilateral granulomatous uveitis, associated with inflammatory annular cyclitis. They had a shallow anterior chamber, a mildly elevated intraocular pressure (under 25 mm Hg and an annular serous retinal detachment. A resolution was observed after specific therapy associated with systemic prednisolone therapy and antiglaucomatous drops.Conclusion: This is the first description of an observational study of six patients with inflammatory annular cyclitis.Keywords: cyclitis, uveitis, malignant glaucoma

  5. Divergent Field Annular Ion Engine Project

    National Aeronautics and Space Administration — The proposed work investigates an approach that would allow an annular ion engine geometry to achieve ion beam currents approaching the Child-Langmuir limit. In this...

  6. Adaptive optics scanning ophthalmoscopy with annular pupils.

    Sulai, Yusufu N; Dubra, Alfredo

    2012-07-01

    Annular apodization of the illumination and/or imaging pupils of an adaptive optics scanning light ophthalmoscope (AOSLO) for improving transverse resolution was evaluated using three different normalized inner radii (0.26, 0.39 and 0.52). In vivo imaging of the human photoreceptor mosaic at 0.5 and 10° from fixation indicates that the use of an annular illumination pupil and a circular imaging pupil provides the most benefit of all configurations when using a one Airy disk diameter pinhole, in agreement with the paraxial confocal microscopy theory. Annular illumination pupils with 0.26 and 0.39 normalized inner radii performed best in terms of the narrowing of the autocorrelation central lobe (between 7 and 12%), and the increase in manual and automated photoreceptor counts (8 to 20% more cones and 11 to 29% more rods). It was observed that the use of annular pupils with large inner radii can result in multi-modal cone photoreceptor intensity profiles. The effect of the annular masks on the average photoreceptor intensity is consistent with the Stiles-Crawford effect (SCE). This indicates that combinations of images of the same photoreceptors with different apodization configurations and/or annular masks can be used to distinguish cones from rods, even when the former have complex multi-modal intensity profiles. In addition to narrowing the point spread function transversally, the use of annular apodizing masks also elongates it axially, a fact that can be used for extending the depth of focus of techniques such as adaptive optics optical coherence tomography (AOOCT). Finally, the positive results from this work suggest that annular pupil apodization could be used in refractive or catadioptric adaptive optics ophthalmoscopes to mitigate undesired back-reflections.

  7. CFD Simulation of Annular Centrifugal Extractors

    S. Vedantam

    2012-01-01

    Full Text Available Annular centrifugal extractors (ACE, also called annular centrifugal contactors offer several advantages over the other conventional process equipment such as low hold-up, high process throughput, low residence time, low solvent inventory and high turn down ratio. The equipment provides a very high value of mass transfer coefficient and interfacial area in the annular zone because of the high level of power consumption per unit volume and separation inside the rotor due to the high g of centrifugal field. For the development of rational and reliable design procedures, it is important to understand the flow patterns in the mixer and settler zones. Computational Fluid Dynamics (CFD has played a major role in the constant evolution and improvements of this device. During the past thirty years, a large number of investigators have undertaken CFD simulations. All these publications have been carefully and critically analyzed and a coherent picture of the present status has been presented in this review paper. Initially, review of the single phase studies in the annular region has been presented, followed by the separator region. In continuation, the two-phase CFD simulations involving liquid-liquid and gas-liquid flow in the annular as well as separator regions have been reviewed. Suggestions have been made for the future work for bridging the existing knowledge gaps. In particular, emphasis has been given to the application of CFD simulations for the design of this equipment.

  8. Sediment particle entrainment in an obstructed annular

    Loureiro, Bruno Venturini; Siqueira, Renato do Nascimento [Faculdade do Centro Leste (UCL), Serra, ES (Brazil). Lab. de Fenomenos de Transporte], e-mail: brunovl@ucl.br, e-mail: renatons@ucl.br

    2006-07-01

    Flow in an annular region with internal cylinder rotation is a classic problem in fluid mechanics and has been widely studied. Besides its importance as a fundamental problem, flow in annular regions has several practical applications. This project was motivated by an application of this kind of flow to the drilling of oil and gas wells. In this work, an erosion apparatus was constructed in order to study the effect of the internal cylinder rotation on particle entrainment in an obstructed annular space and bed package as well. The study also analyzed the influence of height of the particles bed on the process performance. The experiment was designed so that the internal cylinder rotation could be measured by an encoder. The fluid temperature was measured by a thermocouple and the experiments were carried out at the temperature of 25 deg C. The study revealed that the particle entrainment for the height of the bed that is close to the center of the cylinders is negligible and the internal cylinder rotation provokes the movement and packing of the bed. For lower height of the bed, with same dimension of the annular gap, the particle entrainment process was satisfactory and the bed compaction was smaller than in the previous case, leading to a more efficient cleaning process in the annular space. (author)

  9. Annular, erythematous skin lesions in a neonate

    Aparna Palit

    2012-01-01

    Full Text Available A 7-day-old premature female infant presented with rapidly progressive, erythematous, annular skin lesions from the 5 th day of life. She was diagnosed provisionally as a case of neonatal lupus erythematosus and was investigated accordingly. Histopathological examination of the skin biopsy specimen revealed presence of hyphae of dermatophytes in the stratum corneum, and the diagnosis was changed to tinea corporis. Differential diagnosis of the annular erythema of infancy has been discussed and the importance of scraping a scaly lesion for KOH preparation in the diagnostic work-up of such a patient has been highlighted.

  10. Stitching algorithm for annular subaperture interferometry

    Xi Hou; Fan Wu; Li Yang; Shibin Wu; Qiang Chen

    2006-01-01

    @@ Annular subaperture interferometry (ASI) has been developed for low cost and flexible test of rotationally symmetric aspheric surfaces, in which accurately combining the subaperture measurement data corrupted by misalignments and noise into a complete surface figure is the key problem. By introducing the Zernike annular polynomials which are orthogonal over annulus, a method that eliminates the coupling problem in the earlier algorithm based on Zernike circle polynomials is proposed. Vector-matrix notation is used to simplify the description and calculations. The performance of this reduction method is evaluated by numerical simulation. The results prove this method with high precision and good anti-noise capability.

  11. Optimal Thrust Vectoring for an Annular Aerospike Nozzle Project

    National Aeronautics and Space Administration — Recent success of an annular aerospike flight test by NASA Dryden has prompted keen interest in providing thrust vector capability to the annular aerospike nozzle...

  12. Experimental critical parameters of enriched uranium solution in annular tank geometries

    Rothe, R.E.

    1996-04-01

    A total of 61 critical configurations are reported for experiments involving various combinations of annular tanks into which enriched uranium solution was pumped. These experiments were performed at two widely separated times in the 1980s under two programs at the Rocky Flats Plant`s Critical Mass Laboratory. The uranyl nitrate solution contained about 370 g of uranium per liter, but this concentration varied a little over the duration of the studies. The uranium was enriched to about 93% [sup 235]U. All tanks were typical of sizes commonly found in nuclear production plants. They were about 2 m tall and ranged in diameter from 0.6 m to 1.5 m. Annular thicknesses and conditions of neutron reflection, moderation, and absorption were such that criticality would be achieved with these dimensions. Only 13 of the entire set of 74 experiments proved to be subcritical when tanks were completely filled with solution. Single tanks of several radial thicknesses were studied as well as small line arrays (1 x 2 and 1 x 3) of annular tanks. Many systems were reflected on four sides and the bottom by concrete, but none were reflected from above. Many experiments also contained materials within and outside the annular regions that contained strong neutron absorbers. One program had such a thick external moderator/absorber combination that no reflector was used at all.

  13. Fluxon Dynamics in Elliptic Annular Josephson Junctions

    Monaco, Roberto; Mygind, Jesper

    2016-01-01

    We analyze the dynamics of a magnetic flux quantum (current vortex) trapped in a current-biased long planar elliptic annular Josephson tunnel junction. The system is modeled by a perturbed sine-Gordon equation that determines the spatial and temporal behavior of the phase difference across the tu...

  14. Annular beam with segmented phase gradients

    Shubo Cheng

    2016-08-01

    Full Text Available An annular beam with a single uniform-intensity ring and multiple segments of phase gradients is proposed in this paper. Different from the conventional superposed vortices, such as the modulated optical vortices and the collinear superposition of multiple orbital angular momentum modes, the designed annular beam has a doughnut intensity distribution whose radius is independent of the phase distribution of the beam in the imaging plane. The phase distribution along the circumference of the doughnut beam can be segmented with different phase gradients. Similar to a vortex beam, the annular beam can also exert torques and rotate a trapped particle owing to the orbital angular momentum of the beam. As the beam possesses different phase gradients, the rotation velocity of the trapped particle can be varied along the circumference. The simulation and experimental results show that an annular beam with three segments of different phase gradients can rotate particles with controlled velocities. The beam has potential applications in optical trapping and optical information processing.

  15. A New Annular Shear Piezoelectric Accelerometer

    Liu, Bin; Kriegbaum, B.

    2000-01-01

    This paper describes the construction and performance of a recently introduced Annular Shear piezoelectric accelerometer, Type 4511. The design has insulated and double-shielded case. The accelerometer housing is made of stainless steel, AISI 316L. Piezoceramic PZ23 is used. The seismic mass...

  16. Annular lichenoid syphilis: A rare entity.

    Khurana, Ananta; Singal, Archana; Gupta, Seema

    2014-01-01

    Syphilis is a disease known for centuries, but still continues to be a diagnostic challenge as the myriad manifestations of secondary syphilis can mimic a lot many dermatological disorders. Lichenoid syphilis is an uncommon entity, reported only occasionally in the penicillin era. We present the case of a 32-year-old woman presenting with localized annular lichenoid lesions on the neck.

  17. Annular Pressure Seals and Hydrostatic Bearings

    2006-11-01

    affecting the rotordynamics of liquid turbopumps, in particular those handling large density fluids. Highlights on the bulk-flow analysis of annular seals... rotordynamic stability. Hydrostatic bearings rely on external fluid pressurization to generate load support and large centering stiffnesses, even in...SEALS IN PUMP APPLICATIONS Seal rotordynamic characteristic have a primary influence on the stability response of high-performance turbomachinery [1

  18. Non newtonian annular alloy solidification in mould

    Moraga, Nelson O.; Garrido, Carlos P. [Universidad de La Serena, Departamento de Ingenieria Mecanica, La Serena (Chile); Castillo, Ernesto F. [Universidad de Santiago de Chile, Departamento de Ingenieria Mecanica, Santiago (Chile)

    2012-08-15

    The annular solidification of an aluminium-silicon alloy in a graphite mould with a geometry consisting of horizontal concentric cylinders is studied numerically. The analysis incorporates the behavior of non-Newtonian, pseudoplastic (n=0.2), Newtonian (n=1), and dilatant (n=1.5) fluids. The fluid mechanics and heat transfer coupled with a transient model of convection diffusion are solved using the finite volume method and the SIMPLE algorithm. Solidification is described in terms of a liquid fraction of a phase change that varies linearly with temperature. The final results make it possible to infer that the fluid dynamics and heat transfer of solidification in an annular geometry are affected by the non-Newtonian nature of the fluid, speeding up the process when the fluid is pseudoplastic. (orig.)

  19. Dynamics of bouncing droplets in annular cavities

    Lentz, Zachary Louis; Jalali, Mir Abbas; Alam, Mohammad-Reza

    2014-11-01

    In a cylindrical bath of silicon oil, vertically excited by a frequency of 45 Hz, we trace the motion of bouncing droplets as they fill an annular region. We compute the mean tangential and radial velocity components of the droplets and show that the maximum tangential velocity is larger than the maximum radial velocity by one order of magnitude. Velocity dispersions have almost equal levels in the radial and tangential directions, and their mean values are 1/4 times smaller than the mean tangential velocity. These results show that bouncing droplets undergo random motions within annular cavities determined by the interference patterns of self-induced circumferential waves. We derive analytical relations between the velocity dispersion and the wavelength of surface waves, and calculate the mean tangential velocity of droplets using the random kicks that they experience at the boundaries of the cavity by inward and outward traveling waves.

  20. Annular and Total Solar Eclipses of 2003

    Espenak, Fred; Anderson, Jay

    2002-01-01

    On Saturday, 2003 May 31, an annular eclipse of the Sun will be visible from a broad corridor that traverses the North Atlantic. The path of the Moon's antumbral shadow begins in northern Scotland, crosses Iceland and central Greenland, and ends at sunrise in Baffin Bay (Canada). A partial eclipse will be seen within the much broader path of the Moon's penumbral shadow, which includes most of Europe, the Middle East, central and northern Asia, and northwestern North America. The trajectory of the Moon's shadow is quite unusual during this event. The shadow axis passes to the far north where it barely grazes Earth's surface. In fact, the northern edge of the antumbra actually misses Earth so that one path limit is defined by the day/night terminator rather than by the shadow's upper edge. As a result, the track of annularity has a peculiar "D" shape that is nearly 1200 kilometers wide. Since the eclipse occurs just three weeks prior to the northern summer solstice, Earth's northern axis is pointed sunwards by 22.8 deg. As seen from the Sun, the antumbral shadow actually passes between the North Pole and the terminator. As a consequence of this extraordinary geometry, the path of annularity runs from east to west rather than the more typical west to east. The event transpires near the Moon's ascending node in Taurus five degrees north of Aldebaran. Since apogee occurs three days earlier (May 28 at 13 UT), the Moon's apparent diameter (29.6 arc-minutes) is still too small to completely cover the Sun (31.6 arc-minutes) resulting in an annular eclipse.

  1. Effect of Annular Slit Geometry on Characteristics of Spiral Jet

    Shigeru Matsuo; Kwon-Hee Lee; Shinsuke Oda; Toshiaki Setoguchi; Heuy-Dong Kim

    2003-01-01

    A spiral flow using an annular slit connected to a conical cylinder does not need special device to generate a tangential velocity component of the flow and differs from swirling flows. Pressurized fluid is supplied to an annular chamber and injected into the convergent nozzle through the annular slit. The annular jet develops into the spiral flow. In the present study, a spiral jet discharged out of nozzle exit was obtained by using a convergent nozzle and an annular slit set in nozzle inlet, and the effect of annular slit geometry on characteristics of the spiral jet was investigated by using a Laser Doppler Velocimeter (LDV) experimentally. Furthermore, velocity distributions of the spiral jet were compared with those of a normal jet.

  2. Arcuate, annular, and polycyclic inflammatory and infectious lesions.

    Sharma, Amit; Lambert, Phelps J; Maghari, Amin; Lambert, W Clark

    2011-01-01

    Common shapes encountered in dermatologic diseases include linear, nummular, annular, polycyclic, and arciform. The last three have a relatively restricted differential, which must be entirely explored. It is not uncommon for a single disease to present in annular, arciform or polycyclic configurations; moreover, the lesions may evolve from being arciform to annular and then become polycyclic. Regardless, recognizing the arrangement of the defect will undoubtedly help in making a diagnosis and guiding subsequent management. We explore diseases that often present in annular, arciform, and/or polycyclic forms.

  3. Granuloma annulare localized to the shaft of the penis

    Trap, R; Wiebe, B

    1993-01-01

    A case of granuloma annulare localized to the shaft of the penis is reported. The differential diagnoses are discussed. Penile granuloma annulare is a rare disorder and it is concluded that biopsies of penile lesions are recommended to verify the correct diagnosis.......A case of granuloma annulare localized to the shaft of the penis is reported. The differential diagnoses are discussed. Penile granuloma annulare is a rare disorder and it is concluded that biopsies of penile lesions are recommended to verify the correct diagnosis....

  4. Finite stretching of an annular plate.

    Biricikoglu, V.; Kalnins, A.

    1971-01-01

    The problem of the finite stretching of an annular plate which is bonded to a rigid inclusion at its inner edge is considered. The material is assumed to be isotropic and incompressible with a Mooney-type constitutive law. It is shown that the inclusion of the effect of the transverse normal strain leads to a rapid variation in thickness which is confined to a narrow edge zone. The explicit solutions to the boundary layer equations, which govern the behavior of the plate near the edges, are presented.

  5. Annular lupus vulgaris mimicking tinea cruris.

    Heo, Young Soo; Shin, Won Woong; Kim, Yong Ju; Song, Hae Jun; Oh, Chil Hwan

    2010-05-01

    Cutaneous tuberculosis is an infrequent form of extrapulmonary tuberculosis. It is often clinically and histopathologically confused with various cutaneous disorders. A 36-year-old man attended our clinic with slowly progressive, asymptomatic, annular skin lesions on both the thighs and buttocks for 10 years. He consulted with many physicians and was improperly treated with an oral antifungal agent for several months under the diagnosis of tinea cruris, but no resolution of his condition was observed. A diagnosis of lupus vulgaris was made based on the histopathologic examination and the polymerase chain reaction assay. Anti-tuberculosis therapy was administered and the lesions started to regress.

  6. Wave turbulence in annular wave tank

    Onorato, Miguel; Stramignoni, Ettore

    2014-05-01

    We perform experiments in an annular wind wave tank at the Dipartimento di Fisica, Universita' di Torino. The external diameter of the tank is 5 meters while the internal one is 1 meter. The tank is equipped by two air fans which can lead to a wind of maximum 5 m/s. The present set up is capable of studying the generation of waves and the development of wind wave spectra for large duration. We have performed different tests including different wind speeds. For large wind speed we observe the formation of spectra consistent with Kolmogorv-Zakharov predictions.

  7. Annular and semicircular lipoatrophies. Report of three cases and review of the literature.

    Rongioletti, F; Rebora, A

    1989-03-01

    Two cases of semicircular lipoatrophy and one of annular lipoatrophy are presented. The reasons why semicircular lipoatrophy, annular lipoatrophy, and annular atrophy of the ankles seem to be different clinical entities are discussed.

  8. Signatures of an annular Fermi sea

    Jo, Insun; Liu, Yang; Pfeiffer, L. N.; West, K. W.; Baldwin, K. W.; Shayegan, M.; Winkler, R.

    2017-01-01

    The concept of a Fermi surface, the constant-energy surface containing all the occupied electron states in momentum, or wave-vector (k ) , space plays a key role in determining electronic properties of conductors. In two-dimensional (2D) carrier systems, the Fermi surface becomes a contour which, in the simplest case, encircles the occupied states. In this case, the area enclosed by the contour, which we refer to as the Fermi sea (FS), is a simple disk. Here we report the observation of an FS with a new topology, namely, an FS in the shape of an annulus. Such an FS is expected in a variety of 2D systems where the energy band dispersion supports a ring of extrema at finite k , but its experimental observation has been elusive. Our study provides (1) theoretical evidence for the presence of an annular FS in 2D hole systems confined to wide GaAs quantum wells and (2) experimental signatures of the onset of its occupation as an abrupt rise in the sample resistance, accompanied by a sudden appearance of Shubnikov-de Haas oscillations at an unexpectedly high frequency whose value does not simply correspond to the (negligible) density of holes contained within the annular FS.

  9. Annular and Total Solar Eclipses of 2010

    Espenak, Fred; Anderson, J.

    2008-01-01

    While most NASA eclipse bulletins cover a single eclipse, this publication presents predictions for two solar eclipses during 2010. This has required a different organization of the material into the following sections. Section 1 -- Eclipse Predictions: The section consists of a general discussion about the eclipse path maps, Besselian elements, shadow contacts, eclipse path tables, local circumstances tables, and the lunar limb profile. Section 2 -- Annular Solar Eclipse of 2010 Ja n 15: The section covers predictions and weather prospects for the annular eclipse. Section 3 -- Total Solar Eclipse of 2010 Jul 11: The se ction covers predictions and weather prospects for the total eclipse. Section 4 -- Observing Eclipses: The section provides information on eye safety, solar filters, eclipse photography, and making contact timings from the path limits. Section 5 -- Eclipse Resources: The final section contains a number of resources including information on the IAU Working Group on Eclipses, the Solar Eclipse Mailing List, the NASA eclipse bulletins on the Internet, Web sites for the two 2010 eclipses, and a summary identifying the algorithms, ephemerides, and paramete rs used in the eclipse predictions.

  10. Sensors Array Technique for Monitoring Aluminum Alloy Spot Welding

    王蕤; 罗震; 单平; 步贤政; 袁书现; 敖三三

    2010-01-01

    In this paper,the sensors array technique is applied to the quality detection of aluminum alloy spot welding.The sensors array has three forms,i.e.,linear magnetic sensors array,annular magnetic sensors array and cross magnetic sensors array.An algorithm based on principal component analysis is proposed to extract the signal eigenvalues.The three types of magnetic sensors array are used in the experiment of monitoring the signal.After the eigenvalues are extracted,they are used to build a relationship with ...

  11. Vortex beam based more stable annular laser guide star

    Luo, Ruiyao; Cui, Wenda; Li, Lei; Sun, Quan; He, Yulong; Wang, Hongyan; Ning, Yu; Xu, Xiaojun

    2016-11-01

    We present an annular laser guide star (LGS) concept for large ground-based telescopes in this paper. The more stable annular LGS is generated by turbulence-resisted vortex beam. In the uplink, a vortex beam tends to wander more slightly than a Gaussian beam does in atmospheric turbulence. This may enable an annular LGS to wander more slightly than a traditional Gaussian beam generated LGS does, which would ease the burden of uplink tip-tilt mirror and benefit a dynamical closed-loop adaptive optics system. We conducted numerical simulation to validate the feasibility of this concept. And we have gotten 31% reduced variance of spot wandering of annular LGS. Besides, we set up a spatial light modulator based laser guide star simulator for beam propagation in turbulent atmosphere to experimentally test the annular LGS concept. Preliminary experimental results are given. To the best of our knowledge, it is the first time this concept is formulated.

  12. Effect of annular secondary conductor in a linear electromagnetic stirrer

    R Madhavan; V Ramanarayanan

    2008-10-01

    This paper presents the variation of average axial force density in the annular secondary conductor of a linear electromagnetic stirrer. Different geometries of secondaries are considered for numerical and experimental validation namely, 1. hollow annular ring, 2. annular ring with a solid cylinder and 3. solid cylinder. Experimental and numerical simulations are performed for a 2-pole in house built 15 kW linear electromagnetic stirrer (EMS). It is observed for a supply current of 200 A at 30 Hz the force densities in the hollow annular ring is 67% higher than the equivalent solid cylinder. The same values are 33% for annular ring with a solid cylinder. Force density variation with supply frequency and current are also reported. Numerical simulations using finite element model are validated with experimental results.

  13. Annular nanoantenna on fibre micro-axicon.

    Grosjean, T; Fahys, A; Suarez, M; Charraut, D; Salut, R; Courjon, D

    2008-02-01

    In this paper, we propose to extend the concept of loop antenna to the optical domain. The aim is to develop a new generation of optical nanocollectors that are sensitive to specific electric or magnetic vectorial field components. For validating our approach, a preliminary one-micron-diameter gold nanoring is micromachined on the apex of a cone lens obtained from a tapered optical fibre. It is shown that such a nano-object behaves as a nano-antenna able to detect the longitudinal electric field from a Bessel beam in radial polarization and the longitudinal magnetic component from a Bessel beam in azimuthal polarization. In the latter case, the annular nano-antenna exhibits the properties of an optical inductance.

  14. Trauma-related papular granuloma annular.

    Hu, Stephanie W; Kaplan, Jennifer; Patel, Rishi R; Kamino, Hideko

    2013-12-16

    Granuloma annulare (GA) is a benign, granulomatous disease with several clinical manifestations, which include localized, generalized, perforating, subcutaneous, patch, papular, and linear forms. We report a case of papular GA of the dorsal aspects of the hands that arose after repeated, direct trauma to the site of subsequent involvement. Although multiple etiologies for GA have been proposed, which include ultraviolet light, arthropod bites, trauma, tuberculin skin tests, viral infections, and PUVA photochemotherapy, the underlying pathogenesis of the disorder remains unclear. However, owing to the key histopathologic findings of focal collagen and elastic fiber degeneration and mucin deosition in GA, it is not surprising that cutaneous trauma may have played a role in connective tissue injury, subsequent degeneration, and the production of a granulomatous response with increased mucin deposition.

  15. Recurrent Annular Peripheral Choroidal Detachment after Trabeculectomy

    Liu, Shaohui; Sun, Lisa L.; Kavanaugh, A. Scott; Langford, Marlyn P.; Liang, Chanping

    2013-01-01

    We report a challenging case of recurrent flat anterior chamber without hypotony after trabeculectomy in a 54-year-old Black male with a remote history of steroid-treated polymyositis, cataract surgery, and uncontrolled open angle glaucoma. The patient presented with a flat chamber on postoperative day 11, but had a normal fundus exam and intraocular pressure (IOP). Flat chamber persisted despite treatment with cycloplegics, steroids, and a Healon injection into the anterior chamber. A transverse B-scan of the peripheral fundus revealed a shallow annular peripheral choroidal detachment. The suprachoroidal fluid was drained. The patient presented 3 days later with a recurrent flat chamber and an annular peripheral choroidal effusion. The fluid was removed and reinforcement of the scleral flap was performed with the resolution of the flat anterior chamber. A large corneal epithelial defect developed after the second drainage. The oral prednisone was tapered quickly and the topical steroid was decreased. One week later, his vision decreased to count fingers with severe corneal stromal edema and Descemet's membrane folds that improved to 20/50 within 24 h of resumption of the oral steroid and frequent topical steroid. The patient's visual acuity improved to 20/20 following a slow withdrawal of the oral and topical steroid. Eight months after surgery, the IOP was 15 mm Hg without glaucoma medication. The detection of a shallow anterior choroidal detachment by transverse B-scan is critical to making the correct diagnosis. Severe cornea edema can occur if the steroid is withdrawn too quickly. Thus, steroids should be tapered cautiously in steroid-dependent patients. PMID:24348402

  16. Recurrent Annular Peripheral Choroidal Detachment after Trabeculectomy

    Shaohui Liu

    2013-10-01

    Full Text Available We report a challenging case of recurrent flat anterior chamber without hypotony after trabeculectomy in a 54-year-old Black male with a remote history of steroid-treated polymyositis, cataract surgery, and uncontrolled open angle glaucoma. The patient presented with a flat chamber on postoperative day 11, but had a normal fundus exam and intraocular pressure (IOP. Flat chamber persisted despite treatment with cycloplegics, steroids, and a Healon injection into the anterior chamber. A transverse B-scan of the peripheral fundus revealed a shallow annular peripheral choroidal detachment. The suprachoroidal fluid was drained. The patient presented 3 days later with a recurrent flat chamber and an annular peripheral choroidal effusion. The fluid was removed and reinforcement of the scleral flap was performed with the resolution of the flat anterior chamber. A large corneal epithelial defect developed after the second drainage. The oral prednisone was tapered quickly and the topical steroid was decreased. One week later, his vision decreased to count fingers with severe corneal stromal edema and Descemet's membrane folds that improved to 20/50 within 24 h of resumption of the oral steroid and frequent topical steroid. The patient's visual acuity improved to 20/20 following a slow withdrawal of the oral and topical steroid. Eight months after surgery, the IOP was 15 mm Hg without glaucoma medication. The detection of a shallow anterior choroidal detachment by transverse B-scan is critical to making the correct diagnosis. Severe cornea edema can occur if the steroid is withdrawn too quickly. Thus, steroids should be tapered cautiously in steroid-dependent patients.

  17. Annular MHD Physics for Turbojet Energy Bypass

    Schneider, Steven J.

    2011-01-01

    The use of annular Hall type MHD generator/accelerator ducts for turbojet energy bypass is evaluated assuming weakly ionized flows obtained from pulsed nanosecond discharges. The equations for a 1-D, axisymmetric MHD generator/accelerator are derived and numerically integrated to determine the generator/accelerator performance characteristics. The concept offers a shockless means of interacting with high speed inlet flows and potentially offers variable inlet geometry performance without the complexity of moving parts simply by varying the generator loading parameter. The cycle analysis conducted iteratively with a spike inlet and turbojet flying at M = 7 at 30 km altitude is estimated to have a positive thrust per unit mass flow of 185 N-s/kg. The turbojet allowable combustor temperature is set at an aggressive 2200 deg K. The annular MHD Hall generator/accelerator is L = 3 m in length with a B(sub r) = 5 Tesla magnetic field and a conductivity of sigma = 5 mho/m for the generator and sigma= 1.0 mho/m for the accelerator. The calculated isentropic efficiency for the generator is eta(sub sg) = 84 percent at an enthalpy extraction ratio, eta(sub Ng) = 0.63. The calculated isentropic efficiency for the accelerator is eta(sub sa) = 81 percent at an enthalpy addition ratio, eta(sub Na) = 0.62. An assessment of the ionization fraction necessary to achieve a conductivity of sigma = 1.0 mho/m is n(sub e)/n = 1.90 X 10(exp -6), and for sigma = 5.0 mho/m is n(sub e)/n = 9.52 X 10(exp -6).

  18. Characteristics of Electromagnetic Pulse Coupling into Annular Apertures

    Yan-Peng Sun

    2013-11-01

    Full Text Available Electromagnetic pulse (EMP coupling into the annular apertures can disturb or damage much electronic equipment. To enhance electronic system’s  capability of anti-electromagnetic interference, the finite difference time domain method (FDTD was employed to study the characteristics of electromagnetic pulse coupling into the cavity enclosures with annular apertures. The coupling characteristics of annular apertures with different shapes (rectangle, square and circle were discussed. It shows that, in the case of the same aperture area, the coupling energy of electromagnetic pulse into the circular annular aperture is smaller than that into the rectangular and the square ones. To the rectangular annular aperture, while the polarization direction of the incident electromagnetic pulse is perpendicular to the long side of the rectangular annular aperture, the coupling energy is larger when the aspect ratio of the rectangular annular aperture is larger. The coupling effect of incident pulse with short pulse width is obviously better than the one with longer pulse width. The resonance phenomenon of the coupled waveform occurs in the cavity.

  19. High speed, high power one-dimensional beam steering from a 6-element optical phased array.

    Huang, W Ronny; Montoya, Juan; Kansky, Jan E; Redmond, Shawn M; Turner, George W; Sanchez-Rubio, Antonio

    2012-07-30

    Beam steering at high speed and high power is demonstrated from a 6-element optical phased array using coherent beam combining (CBC) techniques. The steering speed, defined as the inverse of the time to required to sweep the beam across the steering range, is 40 MHz and the total power is 396 mW. The measured central lobe FWHM width is 565 μrad. High on-axis intensity is maintained periodically by phase-locking the array via a stochastic-parallel-gradient-descent (SPGD) algorithm. A master-oscillator-power-amplifier (MOPA) configuration is used where the amplifier array elements are semiconductor slab-coupled-optical-waveguide-amplifiers (SCOWAs). The beam steering is achieved by LiNbO(3) phase modulators; the phase-locking occurs by current adjustment of the SCOWAs. The system can be readily scaled to GHz steering speed and multiwatt-class output.

  20. Virtual cathode microwave generator having annular anode slit

    Kwan, Thomas J. T.; Snell, Charles M.

    1988-01-01

    A microwave generator is provided for generating microwaves substantially from virtual cathode oscillation. Electrons are emitted from a cathode and accelerated to an anode which is spaced apart from the cathode. The anode has an annular slit therethrough effective to form the virtual cathode. The anode is at least one range thickness relative to electrons reflecting from the virtual cathode. A magnet is provided to produce an optimum magnetic field having the field strength effective to form an annular beam from the emitted electrons in substantial alignment with the annular anode slit. The magnetic field, however, does permit the reflected electrons to axially diverge from the annular beam. The reflected electrons are absorbed by the anode in returning to the real cathode, such that substantially no reflexing electrons occur. The resulting microwaves are produced with a single dominant mode and are substantially monochromatic relative to conventional virtual cathode microwave generators.

  1. Polyharmonic functions of infinite order on annular regions

    Kounchev, Ognyan; Render, Hermann

    2013-01-01

    Polyharmonic functions $f$ of infinite order and type $\\tau$ on annular regions are systematically studied. The first main result states that the Fourier-Laplace coefficients $f_{k,l}(r)$ of a polyharmonic function $f$ of infinite order and type $0$ can be extended to analytic functions on the complex plane cut along the negative semiaxis. The second main result gives a constructive procedure via Fourier-Laplace series for the analytic extension of a polyharmonic function on annular ...

  2. Experiments on soliton motion in annular Josephson junctions

    Davidson, A.; Dueholm, B.; Pedersen, Niels Falsig

    1986-01-01

    We report here the results of an extensive experimental investigation of soliton dynamics in Josephson junctions of different annular geometries. The annular geometry is unique in that it allows for the study of undisturbed soliton motion as well as soliton–antisoliton collisons, since there are ...... for a single trapped soliton, and evidence linking the stability of the soliton to surface damping. Journal of Applied Physics is copyrighted by The American Institute of Physics....

  3. New mitral annular force transducer optimized to distinguish annular segments and multi-plane forces.

    Skov, Søren Nielsen; Røpcke, Diana Mathilde; Ilkjær, Christine; Rasmussen, Jonas; Tjørnild, Marcell Juan; Jimenez, Jorge H; Yoganathan, Ajit P; Nygaard, Hans; Nielsen, Sten Lyager; Jensen, Morten Olgaard

    2016-03-21

    Limited knowledge exists about the forces acting on mitral valve annuloplasty repair devices. The aim of this study was to develop a new mitral annular force transducer to measure the forces acting on clinically used mitral valve annuloplasty devices. The design of an X-shaped transducer in the present study was optimized for simultaneous in- and out-of-plane force measurements. Each arm was mounted with strain gauges on four circumferential elements to measure out-of-plane forces, and the central parts of the X-arms were mounted with two strain gauges to measure in-plane forces. A dedicated calibration setup was developed to calibrate isolated forces with tension and compression for in- and out-of-plane measurements. With this setup, it was possible with linear equations to isolate and distinguish measured forces between the two planes and minimize transducer arm crosstalk. An in-vitro test was performed to verify the crosstalk elimination method and the assumptions behind it. The force transducer was implanted and evaluated in an 80kg porcine in-vivo model. Following crosstalk elimination, in-plane systolic force accumulation was found to be in average 4.0±0.1N and the out-of-plane annular segments experienced an average force of 1.4±0.4N. Directions of the systolic out-of-plane forces indicated movements towards a saddle shaped annulus, and the transducer was able to measure independent directional forces in individual annular segments. Further measurements with the new transducer coupled with clinical annuloplasty rings will provide a detailed insight into the biomechanical dynamics of these devices.

  4. Sonographic evaluation of digital annular pulley tears

    Martinoli, C.; Derchi, L.E. [Istituto di Radiologia, Universita di Genova, Genoa (Italy); Bianchi, S.; Garcia, J.F. [Dept. de Radiologie, Hopital Cantonal Universitaire de Geneve (Switzerland); Nebiolo, M. [Reparto Pronto Soccorso Medico, Pietra Ligure (Italy)

    2000-07-01

    Objective. To evaluate the sonographic (US) appearance of digital annular pulley (DAP) tears in high-level rock climbers. Design and patients. We performed a retrospective analysis of the US examinations of 16 high-level rock climbers with clinical signs of DAP lesions. MRI and surgical evaluation were performed in five and three patients respectively. The normal US and MRI appearances of DAP were evaluated in 40 and three normal fingers respectively. Results. Nine of 16 patients presented a DAP tear. In eight subjects (seven with complete tears involving the fourth finger and one the fifth finger), US diagnosis was based on the indirect sign of volar bowstringing of the flexor tendons. Injured pulleys were not appreciated by US. Tears concerned the A2 and A3 in six patients and the A3 and A4 in two patients. A2 pulley thickening and hypoechogenicity compatible with a partial tear was demonstrated in one patient. MRI and surgical data correlated well with the US findings. Four patients had tenosynovitis of the flexor tendons but no evidence of pulley disruption. US examinations of three patients were normal. In the healthy subjects US demonstrated DAP in 16 of 40 digits. Conclusion. US can diagnose DAP tears and correlates with the MRI and surgical data. Because of its low cost and non-invasiveness we suggest US as the first imaging modality in the evaluation of injuries of the digital pulley. (orig.)

  5. Impulsively started, steady and pulsated annular inflows

    Abdel-Raouf, Emad; Sharif, Muhammad A. R.; Baker, John

    2017-04-01

    A computational investigation was carried out on low Reynolds number laminar inflow starting annular jets using multiple blocking ratios and atmospheric ambient conditions. The jet exit velocity conditions are imposed as steady, unit pulsed, and sinusoidal pulsed while the jet surroundings and the far-field jet inlet upstream conditions are left atmospheric. The reason is to examine the flow behavior in and around the jet inlet under these conditions. The pulsation mode behavior is analyzed based on the resultant of the momentum and pressure forces at the entry of the annulus, the circulation and vortex formation, and the propulsion efficiency of the inflow jets. The results show that under certain conditions, the net force of inflow jets (sinusoidal pulsed jets in particular) could point opposite to the flow direction due to the adverse pressure drops in the flow. The propulsion efficiency is also found to increase with pulsation frequency and the sinusoidal pulsed inflow jets are more efficient than the unit pulsed inflow jets. In addition, steady inflow jets did not trigger the formation of vortices, while unit and sinusoidal pulsed inflow jets triggered the formation of vortices under a certain range of frequencies.

  6. Solar cycle modulation of Southern Annular Mode

    Kuroda, Yuhji

    2016-04-01

    Climate is known to be affected by various factors, including oceanic changes and volcanic eruptions. 11-year solar cycle change is one of such important factors. Observational analysis shows that the winter-mean North Atlantic Oscillation (NAO) and late-winter/spring Southern Annular Mode (SAM) show structural modulation associated with 11-year solar cycle. In fact, these signals tend to extend from surface to upper stratosphere and persistent longer period only in the High Solar (HS) years. In the present study, we used 35-year record of ERA-Interim reanalysis data and performed wave-energy and momentum analysis on the solar-cycle modulation of the SAM to examine key factors to create such solar-SAM relationship. It is found that enhanced wave-mean flow interaction tends to take place in the middle stratosphere in association with enhanced energy input from diabatic heating on September only in HS years. The result suggests atmospheric and solar conditions on September are keys to create solar-SAM relationship.

  7. Integrated field emission array for ion desorption

    Resnick, Paul J; Hertz, Kristin L.; Holland, Christopher; Chichester, David

    2016-08-23

    An integrated field emission array for ion desorption includes an electrically conductive substrate; a dielectric layer lying over the electrically conductive substrate comprising a plurality of laterally separated cavities extending through the dielectric layer; a like plurality of conically-shaped emitter tips on posts, each emitter tip/post disposed concentrically within a laterally separated cavity and electrically contacting the substrate; and a gate electrode structure lying over the dielectric layer, including a like plurality of circular gate apertures, each gate aperture disposed concentrically above an emitter tip/post to provide a like plurality of annular gate electrodes and wherein the lower edge of each annular gate electrode proximate the like emitter tip/post is rounded. Also disclosed herein are methods for fabricating an integrated field emission array.

  8. Integrated field emission array for ion desorption

    Resnick, Paul J; Hertz, Kristin L; Holland, Christopher; Chichester, David; Schwoebel, Paul

    2013-09-17

    An integrated field emission array for ion desorption includes an electrically conductive substrate; a dielectric layer lying over the electrically conductive substrate comprising a plurality of laterally separated cavities extending through the dielectric layer; a like plurality of conically-shaped emitter tips on posts, each emitter tip/post disposed concentrically within a laterally separated cavity and electrically contacting the substrate; and a gate electrode structure lying over the dielectric layer, including a like plurality of circular gate apertures, each gate aperture disposed concentrically above an emitter tip/post to provide a like plurality of annular gate electrodes and wherein the lower edge of each annular gate electrode proximate the like emitter tip/post is rounded. Also disclosed herein are methods for fabricating an integrated field emission array.

  9. X-ray diffraction from bone employing annular and semi-annular beams.

    Dicken, A J; Evans, J P O; Rogers, K D; Stone, N; Greenwood, C; Godber, S X; Prokopiou, D; Clement, J G; Lyburn, I D; Martin, R M; Zioupos, P

    2015-08-07

    There is a compelling need for accurate, low cost diagnostics to identify osteo-tissues that are associated with a high risk of fracture within an individual. To satisfy this requirement the quantification of bone characteristics such as 'bone quality' need to exceed that provided currently by densitometry. Bone mineral chemistry and microstructure can be determined from coherent x-ray scatter signatures of bone specimens. Therefore, if these signatures can be measured, in vivo, to an appropriate accuracy it should be possible by extending terms within a fracture risk model to improve fracture risk prediction.In this preliminary study we present an examination of a new x-ray diffraction technique that employs hollow annular and semi-annular beams to measure aspects of 'bone quality'. We present diffractograms obtained with our approach from ex vivo bone specimens at Mo Kα and W Kα energies. Primary data is parameterized to provide estimates of bone characteristics and to indicate the precision with which these can be determined.

  10. On the mixing enhancement in annular flows

    Moradi, H. V.; Floryan, J. M.

    2017-02-01

    The potential for mixing enhancement associated with the use of axisymmetric ribs in annular flows has been analyzed. The enhancement relies on the use of streamwise vortices produced by the centrifugal instability. Conditions leading to the formation of such vortices have been established for a wide range of geometric parameters of interest using linear stability theory. It has been demonstrated that vortices can be formed only in the presence of ribs with O(1) wavelengths. Slopes of the bounding walls in the case of the long wavelength ribs are too small to create centrifugal forces sufficient for flow destabilization. In the case of short wavelength ribs, the slopes become excessively large, resulting in the stream moving away from the wall and becoming rectilinear and, thus, reducing the magnitude of the centrifugal force field. It has been shown that decreasing the annulus' radius reduces the critical Reynolds number when ribs are placed at the inner cylinder but increases when the ribs are placed at the outer cylinder. The onset of the shear-driven instability has been investigated as the resulting travelling waves may interfere with the formation of vortices. It has been shown that the axisymmetric waves play the critical role for annuli with large radii while the spiral waves play the critical role for annuli with small radii. The ribs always reduce the critical Reynolds number for the travelling waves when compared with the onset conditions for smooth annuli. The conduit geometries giving preference to the formation of vortices while avoiding creation of the travelling waves have been identified. It is demonstrated that predictions of flow characteristics determined through the analysis of sinusoidal ribs provide a good approximation of the flow response to ribs of arbitrary shape.

  11. Far-field Diffraction Properties of Annular Walsh Filters

    Pubali Mukherjee

    2013-01-01

    Full Text Available Annular Walsh filters are derived from the rotationally symmetric annular Walsh functions which form a complete set of orthogonal functions that take on values either +1 or −1 over the domain specified by the inner and outer radii of the annulus. The value of any annular Walsh function is taken as zero from the centre of the circular aperture to the inner radius of the annulus. The three values 0, +1, and −1 in an annular Walsh function can be realized in a corresponding annular Walsh filter by using transmission values of zero amplitude (i.e., an obscuration, unity amplitude and zero phase, and unity amplitude and phase, respectively. Not only the order of the Walsh filter but also the size of the inner radius of the annulus provides an additional degree of freedom in tailoring of point spread function by using these filters for pupil plane filtering in imaging systems. In this report, we present the far-field amplitude characteristics of some of these filters to underscore their potential for effective use in several demanding applications like high-resolution microscopy, optical data storage, microlithography, optical encryption, and optical micromanipulation.

  12. Stratospheric Annular Modes Induced By Stationary Wave Forcing

    Körnich, H.; Schmitz, G.

    The variability of the winter stratosphere shows distinguishable features in the north- ern and southern hemisphere. Since these differences are based on the different plan- etary waves of the underlying atmosphere, we explore the mechanism how stationary wave forcing in the troposphere can induce a stratospheric Annular Mode using a simple GCM. The model KMCM (Kühlungsborn Mechanistic Circulation Model) extends from the ground up to 60 km height and produces a reasonable winter climate. It takes into account the different large-scale wave forcings in the troposphere as prescribed pro- cesses. This allows us to examine the stratospheric Annular-Mode generation depend- ing on different wave forcings under perpetual January conditions. Principal com- ponent analysis is applied to identify the variability patterns of the geopotential and of the zonally averaged zonal wind. By this way, it is shown that the amplitude and composition of the orographic and thermal eddy forcing determines the stratospheric Annular Mode and the related downward propagation in the temperature field. Further model simplifications are introduced in order to understand the mechanism of the stratospheric AM-generation. Using a linear model version we illuminate the influence of the different wave forcing processes on the Annular Modes. Addition- ally, a constant-troposphere model is used to clarify the importance of transient and stationary waves. Finally, the Annular Mode is interpreted in terms of the dynamical coupling of the troposphere and stratosphere.

  13. Sensors Array Technique for Monitoring Aluminum Alloy Spot Welding

    WANG Rui; LUO Zhen; SHAN Ping; BU Xianzheng; YUAN Shuxian; AO Sansan

    2010-01-01

    In this paper, the sensors array technique is applied to the quality detection of aluminum alloy spot weld-ing. The sensors array has three forms, i.e., linear magnetic sensors array, annular magnetic sensors array and cross magnetic sensors array. An algorithm based on principal component analysis is proposed to extract the signal eigen-values. The three types of magnetic sensors array are used in the experiment of monitoring the signal. After the eigen-values are extracted, they are used to build a relationship with the nugget information. The result shows that when the distance between the core of the array and the pole is 60 mm, the arrays work best. In this case, when the eigenvalues' range of the linear array is 0.006 5-0.015 1, the quality of the spots is eligible. To the annular and cross array, when the ranges are 0.082 9—0.131 6 and 0.085 1—0.098 2 respectively, the nugget quality is eligible.

  14. Localized Bioconvection Patterns and Their Initial State Dependency in Euglena gracilis Suspensions in an Annular Container

    Shoji, Erika; Nishimori, Hiraku; Awazu, Akinori; Izumi, Shunsuke; Iima, Makoto

    2014-04-01

    Localized patterns of bioconvection in Euglena gracilis suspensions were experimentally analyzed in an annular container. Near the critical mean density of convection, we succeeded in isolating two basic types of localized convection patterns. One was an almost stationary pattern consisting of two convection cells centered by an isolated high-density region of the microorganism where a downflow was generated, which we call a "bioconvection unit". The other was a traveling wave pattern consisting of an array of moving high-density waves bounded in a certain area. The effect of the mean density of E. gracilis on the emergence of the localized convection pattern was also examined. Near the critical mean density, we found that the emergence probability of the localized convection pattern depends on the initial state, i.e., whether E. gracilis has a uniform or localized distribution, which suggests that the system is bistable. Such bistability is often accompanied by localized structures in spatially extended dissipative systems.

  15. Multifold Laser Resonator for Annular Gain Media.

    Duncan, Arlene

    Available from UMI in association with The British Library. A pair of spherical mirrors enclosing an off-axis beam in a hyperboloidal ray trajectory describes a Herriott Cell. Placed inside a linear Fabry Perot resonator, a multifold laser resonator is formed. By considering this resonator when coupled to a coaxial, annular geometry, RF discharge excited CO_2 gain media in a sealed-off configuration, this thesis aims to formulate the scaling laws and characterise the main features of these devices. To help establish a design baseline and to allow the determination of practical results, the scaling laws are developed with an (arbitrary) limit on the physical size of the laser module of 100 x 10 x 10cm. Within this size, design algorithms demonstrate the limitation on scaling power to about 460W. Output beam characteristics are investigated for a range of multifold lasers to determine the effects the choice of design parameters has and the predicted TEM _{00} output expected. All incongruities are found to be primarily dependent on whether or not the beam traverses the complete Herriott Cell, but more directly on the radial gain and refractive index variations present in the gain medium. In terms of polarization, image rotation and astigmatism, the Cell has been analysed to determine the non-planar influence. Theoretical and experimental results tie in with the conclusions from the previous observations. The use of tolerance equations and a study of deviations in beam spot positions on the mirrors under misalignments illustrates; dependence on electrode dimensions; greatest sensitivity to Cell mirror tilts; and a shift in the ray envelope cross-section from circular to elliptical on all resonator adjustments. At all stages results are compared with existing multifold lasers and other lasers with similar output powers. As a whole the thesis demonstrates the potential of these lasers in the medium power range as sealed-off devices with excellent mode quality. Increased

  16. Annular lupus vulgaris: an unusual case undiagnosed for five years.

    Gönül, Müzeyyen; Kiliç, Arzu; Külcü Cakmak, Seray; Gül, Ulker; Koçak, Oğuzhan; Demiriz, Murat

    2007-01-01

    Tuberculosis is still a serious problem in both developing and developed countries. It is often confused with various cutaneous disorders both clinically and histopathologically.A 46-year-old woman attended our clinic with progressive, asymptomatic, annular skin lesions on her right upper extremity for 5 years. She had received many different therapies for these lesions at other institutions previously but these medications were not effective and the lesions deteriorated. On dermatological examination, well-demarcated, irregular bordered, violaceous colored, elevated and crusted annular lesions on her right hand dorsum and forearm were observed. She was diagnosed as having lupus vulgaris clinically and histopathologically. Antituberculosis therapy was administered and regression of the lesions started in the second week of medication.We report a case of long-standing, undiagnosed and uncommon, annular form of lupus vulgaris. We want to stress that clinical and histopathological findings are still important for the diagnosis of cutaneous tuberculosis.

  17. Portal Annular Pancreas: A Rare and Overlooked Anomaly

    Mittal, Puneet; Gupta, Ranjana; Mittal, Amit; Ahmed, Arshad

    2017-01-01

    Summary Background Portal annular pancreas is a rare pancreatic developmental anomaly which is often overlooked at imaging, and often diagnosed retrospectively when it is detected incidentally at the time of surgery. Although the anomaly itself is asymptomatic, it becomes important in cases where pancreatic resection/anastomosis is planned, because of varying ductal anatomy, risk of ductal injury and increased risk of postoperative pancreatic fistula formation. Case Report We present imaging findings in a case of portal annular pancreas in a 45-year-old male patient. Conclusions Portal annular pancreas is a rare and often neglected pancreatic anomaly due to a lack of awareness of this entity. With the advent of MDCT and MRI, accurate preoperative diagnosis of this condition is possible.

  18. Vibration Analysis of Annular Sector Plates under Different Boundary Conditions

    Dongyan Shi

    2014-01-01

    Full Text Available An analytical framework is developed for the vibration analysis of annular sector plates with general elastic restraints along each edge of plates. Regardless of boundary conditions, the displacement solution is invariably expressed as a new form of trigonometric expansion with accelerated convergence. The expansion coefficients are treated as the generalized coordinates and determined using the Rayleigh-Ritz technique. This work allows a capability of modeling annular sector plates under a variety of boundary conditions and changing the boundary conditions as easily as modifying the material properties or dimensions of the plates. Of equal importance, the proposed approach is universally applicable to annular sector plates of any inclusion angles up to 2π. The reliability and accuracy of the current method are adequately validated through numerical examples.

  19. Inverted annular flow heat transfer in a natural circulation loop

    Ozawa, M.; Umekawa, H.; Shiba, Y.; Yano, T. [Kansai Univ., Osaka (Japan)

    1998-07-01

    Gravity-feed reflooding experiment was conducted in a natural circulation loop of liquid nitrogen. The cooling curve of high temperature tube wall had a characteristic feature, i.e. initial rapid cooling with steam binding, relatively long-time plateau, gradual decrease with or without flow oscillation, and final drastic decrease during quenching process. Such phenomena had close relationship to the heated wall dynamics and heating power transient. To provide fundamental understanding on the present phenomena, the heat transfer data in inverted annular and dispersed flows were obtained under steady or oscillatory flow condition. The experimental data suggested that the heat transfer coefficient in the inverted annular or dispersed flow regimes is a slightly increasing function of heat flux but significantly depended on the tube diameter. The flow oscillation deteriorated heat transfer slightly in the inverted annular and dispersed flow regimes but significantly in the quenching process.

  20. Mathematical Model of Combustion in Blunt Annular Ceramic Burner

    2001-01-01

    The computer simulation of the combustion process in blast furnace (BF) stove has been studied by using the k-ε-g turbulent diffusion flame model. The combustion process in blunt annular ceramic burner was calculated by using the software. The profiles of gas and air velocity, temperature of the combustion products, concentration of the components, and the shape and length of the flame during combustion have been researched . Compared with the original annular ceramic burner, the new design of the blunt one improves the mixing of the gas and the air significantly, and shortened the length of the flame.

  1. Enhanced spontaneous emission rate in annular plasmonic nanocavities

    Kroekenstoel, E. J. A.; Verhagen, E.; Walters, R. J.; Kuipers, L.; Polman, A.

    2009-12-01

    The spontaneous emission rate of erbium ions is enhanced by coupling to localized plasmonic resonances in subwavelength annular apertures in a Au film. The Er3+ ions, embedded in SiO2, are selectively located inside the apertures. The annular apertures act as nanocavities, enhancing the local density of optical states at the Er emission wavelength of 1.54 μm when the cavities are tuned to that wavelength. We show that this leads to an eightfold increase of the photoluminescence intensity, in conjunction with a 2.4-fold enhancement of the spontaneous emission rate.

  2. Patch Type Granuloma Annulare Imitating Cutaneous T-Cell Lymphoma

    Seval Doğruk Kaçar

    2015-03-01

    Full Text Available Granuloma annulare (GA is a benign inflammatory skin disease with distinct clinical and histopathological findings. Patch type GA is described with erythematous patches beyond the classical clinical appearance and an interstitial pattern is observed without histopathologically granulomas with disseminated histiocytes among collagen bundles and vessels. Here we report 46 year old woman diagnosed as patch type GA after a punch biopsy performed from the annular bordered patches in belly area, which is a classical area for mycosis fungoides (MF evolution, and lesions increasingly spreading out within a 2 year period.

  3. Mitral-aortic annular enlargement: modification of Manouguian's technique

    Costa Mario Gesteira

    2002-01-01

    Full Text Available We hereby present a technical modification for mitral-aortic annular enlargement. The mitral valve is replaced through the retro-septal approach, avoiding patches for left atrial roof closure. We report a mitral-aortic valve replacement in a patient whose original annuli would preclude adequate prostheses. The simultaneous annular enlargement may be necessary for avoiding patient-prosthesis mismatch and for reconstructing destroyed mitral and aortic annuli. The technique may minimize the risk of bleeding and of paravalvular leakage, using an approach well known to cardiac surgeons.

  4. Multi-functional annular fairing for coupling launch abort motor to space vehicle

    Camarda, Charles J. (Inventor); Scotti, Stephen J. (Inventor); Buning, Pieter G. (Inventor); Bauer, Steven X. S. (Inventor); Engelund, Walter C. (Inventor); Schuster, David M. (Inventor)

    2011-01-01

    An annular fairing having aerodynamic, thermal, structural and acoustic attributes couples a launch abort motor to a space vehicle having a payload of concern mounted on top of a rocket propulsion system. A first end of the annular fairing is fixedly attached to the launch abort motor while a second end of the annular fairing is attached in a releasable fashion to an aft region of the payload. The annular fairing increases in diameter between its first and second ends.

  5. Modeling and control of water disinfection process in annular photoreactors

    Keesman, K.J.; Vries, D.; Mourik, van S.; Zwart, H.

    2007-01-01

    Abstract¿ As an alternative or addition to complex physical modeling, in this paper transfer function models of the disinfection process in annular photoreactors under different flow conditions are derived. These transfer function models allow an analytical evaluation of the system dynamics and the

  6. Modelling of water disinfection process in annular photoreactors

    Keesman, K.J.; Parasoglou, M.; Vries, D.

    2006-01-01

    As an alternative or addition to complex physical modelling, in this paper transfer function models of the disinfection process in annular photoreactors under different flow conditions are derived. These transfer function models allow an analytical evaluation of the system dynamics and the control s

  7. Modeling and control of water disinfection process in annular photoreactors

    Keesman, K.J.; Vries, D.; Mourik, van S.; Zwart, H.J.; Tzafestas, S.

    2007-01-01

    As an alternative or addition to complex physical modeling, in this paper transfer function models of the disinfection process in annular photoreactors under different flow conditions are derived. These transfer function models allow an analytical evaluation of the system dynamics and the control st

  8. Design curves for circular and annular duct silencers

    Watson, Willie R.; Ramakrishnan, R.

    1989-01-01

    Conventional models of sound propagation between porous walls (Scott, 1946) are adapted in order to calculate design curves for the lined circular and annular-duct silencers used in HVAC systems. The derivation of the governing equations is outlined, and results for two typical cases are presented graphically. Good agreement with published experimental data is demonstrated.

  9. Annular-cladding erbium doped multicore fiber for SDM amplification.

    Jin, Cang; Ung, Bora; Messaddeq, Younès; LaRochelle, Sophie

    2015-11-16

    We propose and numerically investigate annular-cladding erbium doped multicore fibers (AC-EDMCF) with either solid or air hole inner cladding to enhance the pump power efficiency in optical amplifiers for spatial division multiplexing (SDM) transmission links. We first propose an all-glass fiber in which a central inner cladding region with a depressed refractive index is introduced to confine the pump inside a ring-shaped region overlapping the multiple signal cores. Through numerical simulations, we determine signal core and annular pump cladding parameters respecting fabrication constraints. We also propose and examine a multi-spot injection scheme for launching the pump in the annular cladding. With this all-glass fiber with annular cladding, our results predict 10 dB increase in gain and 21% pump power savings compared to the standard double cladding design. We also investigate a fiber with an air hole inner cladding to further enhance the pump power confinement and minimize power leaking into the inner cladding. The results are compared to the all-glass AC-EDMCF.

  10. Fluxon dynamics in long annular Josephson tunnel junctions

    Martucciello, N.; Mygind, Jesper; Koshelets, V.P.

    1998-01-01

    Single-fluxon dynamics has been experimentally investigated in high-quality Nb/Al-AlOx/Nb annular Josephson tunnel junctions having a radius much larger than the Josephson penetration depth. Strong evidence of self-field effects is observed. An external magnetic field in the barrier plane acts...

  11. Performance of the Pierre Auger Observatory Surface Array

    Bertou, X

    2005-01-01

    The surface detector of the Pierre Auger Observatory is a 1600 water Cherenkov tank array on a triangular 1.5 km grid. The signals from each tank are read out using three 9'' photomultipliers and processed at a sampling frequency of 40 MHz, from which a local digital trigger efficiently selects shower candidates. GPS signals are used for time synchronization and a wireless communication system connects all tanks to the central data acquisition system. Power is provided by a stand-alone solar panel system. With large ambient temperature variations, that can reach over 20 degrees in 24 hours, high salinity, dusty air, high humidity inside the tank, and remoteness of access, the performance and reliability of the array is a challenge. Several key parameters are constantly monitored to ensure consistent operation. The Surface Array has currently over 750 detectors and has been in reliable operation since January 2004. Good uniformity in the response of different detectors and good long term stability is observed.

  12. Wire-number effects on high-power annular z-pinches and some characteristics at high wire number

    SANFORD,THOMAS W. L.

    2000-05-23

    Characteristics of annular wire-array z-pinches as a function of wire number and at high wire number are reviewed. The data, taken primarily using aluminum wires on Saturn are comprehensive. The experiments have provided important insights into the features of wire-array dynamics critical for high x-ray power generation, and have initiated a renaissance in z-pinches when high numbers of wires are used. In this regime, for example, radiation environments characteristic of those encountered during the early pulses required for indirect-drive ICF ignition on the NIF have been produced in hohlraums driven by x-rays from a z-pinch, and are commented on here.

  13. PMN-PT single-crystal high-frequency kerfless phased array.

    Chen, Ruimin; Cabrera-Munoz, Nestor E; Lam, Kwok Ho; Hsu, Hsiu-sheng; Zheng, Fan; Zhou, Qifa; Shung, K Kirk

    2014-06-01

    This paper reports the design, fabrication, and characterization of a miniature high-frequency kerfless phased array prepared from a PMN-PT single crystal for forward-looking intravascular or endoscopic imaging applications. After lapping down to around 40 μm, the PMN-PT material was utilized to fabricate 32-element kerfless phased arrays using micromachining techniques. The aperture size of the active area was only 1.0 × 1.0 mm. The measured results showed that the array had a center frequency of 40 MHz, a bandwidth of 34% at -6 dB with a polymer matching layer, and an insertion loss of 20 dB at the center frequency. Phantom images were acquired and compared with simulated images. The results suggest that the feasibility of developing a phased array mounted at the tip of a forward-looking intravascular catheter or endoscope. The fabricated array exhibits much higher sensitivity than PZT ceramic-based arrays and demonstrates that PMN-PT is well suited for this application.

  14. Fabry-Perot CCD annular-summing spectroscopy: study and implementation for aeronomy applications.

    Coakley, M M; Roesler, F L; Reynolds, R J; Nossal, S

    1996-11-20

    The technique of Fabry-Perot CCD annular-summing spectroscopy, with particular emphasis on applications in aeronomy, is discussed. Parameter choices for optimizing performance by the use of a standard format CCD array are detailed. Spectral calibration methods, techniques for determining the ring pattern center, and effects imposed by limited radial resolution caused by superpixel size, variable by on-chip binning, are demonstrated. The technique is carefully evaluated experimentally relative to the conventional scanning Fabry-Perot that uses a photomultiplier detector. We evaluate three extreme examples typical of aeronomical spectroscopy using calculated signal-to-noise ratios. Predicted sensitivity gains of 10-30 are typical. Of the cases considered, the largest savings in integration time are estimated for the day sky thermospheric O(1)D case, in which the bright sky background dominates the CCD read noise. For profile measurements of faint night sky emission lines, such as exospheric hydrogen Balmer-α, long integration times are required to achieve useful signal-to-noise ratios. In such cases, CCD read noise is largely overcome. Predictions of a factor of 10-15 savings in integration time for night sky Balmer-α observations are supported by field tests. Bright, isolated night sky lines such as thermospheric O(1)D require shorter integration times, and more modest gains dependent on signal level are predicted. For such cases it appears from estimate results that the Fabry-Perot CCD annular-summing technique with a conventional rectangular format may be outperformed by a factor of 2-5 by special CCD formats or by unusual optical coupling configurations that reduce the importance of read noise, based on the ideal transmission for any additional optics used in these configurations.

  15. Production of annular flat-topped vortex beams

    Jiannong Chen; Yongjiang Yu; Feifei Wang

    2011-01-01

    @@ A model of an annular flat-topped vortex beam based on multi-Gaussian superimposition is proposed. We experimentally produce this beam with a computer-generated hologram (CGH) displayed on a spatial light modulator (SLM). The power of the beam is concentrated on a single-ring structure and has an extremely strong radial intensity gradient. This beam facilitates various applications ranging from Sisyphus atom cooling to micro-particle trapping.%A model of an annular fiat-topped vortex beam based on multi-Gaussian superimposition is proposed. We experimentally produce this beam with a computer-generated hologram (CGH) displayed on a spatial light modulator (SLM). The power of the beam is concentrated on a single-ring structure and has an extremely strong radial intensity gradient. This beam facilitates various applications ranging from Sisyphus atom cooling to micro-particle trapping.

  16. Energy and Exergy Analysis of an Annular Thermoelectric Heat Pump

    Kaushik, S. C.; Manikandan, S.; Hans, Ranjana

    2016-07-01

    In this paper, the concept of an annular thermoelectric heat pump (ATEHP) has been introduced. An exoreversible thermodynamic model of the ATEHP considering the Thomson effect in conjunction with Peltier, Joule and Fourier heat conduction has been investigated using exergy analysis. New expressions for dimensionless heating power, optimum current at the maximum energy, exergy efficiency conditions and dimensionless irreversibilities in the ATEHP are derived. The results show that the heating power, energy and exergy efficiency of the ATEHP are lower than the flat-plate thermoelectric heat pump. The effects of annular shape parameter ( S r = r 2 /r 1), dimensionless temperature ratio ( θ = T h /T c) and the electrical contact resistances on the heating power, energy/exergy efficiency of an ATEHP have been studied. This study will help in the designing of actual ATEHP systems.

  17. Wind generated rogue waves in an annular wave flume

    Toffoli, A; Salman, H; Monbaliu, J; Frascoli, F; Dafilis, M; Stramignoni, E; Forza, R; Manfrin, M; Onorato, M

    2016-01-01

    We investigate experimentally the statistical properties of a wind-generated wave field and the spontaneous formation of rogue waves in an annular flume. Unlike many experiments on rogue waves, where waves are mechanically generated, here the wave field is forced naturally by wind as it is in the ocean. What is unique about the present experiment is that the annular geometry of the tank makes waves propagating circularly in an {\\it unlimited-fetch} condition. Within this peculiar framework, we discuss the temporal evolution of the statistical properties of the surface elevation. We show that rogue waves and heavy-tail statistics may develop naturally during the growth of the waves just before the wave height reaches a stationary condition. Our results shed new light on the formation of rogue waves in a natural environment.

  18. Axisymmetric buckling of laminated thick annular spherical cap

    Dumir, P. C.; Dube, G. P.; Mallick, A.

    2005-03-01

    Axisymmetric buckling analysis is presented for moderately thick laminated shallow annular spherical cap under transverse load. Buckling under central ring load and uniformly distributed transverse load, applied statically or as a step function load is considered. The central circular opening is either free or plugged by a rigid central mass or reinforced by a rigid ring. Annular spherical caps have been analysed for clamped and simple supports with movable and immovable inplane edge conditions. The governing equations of the Marguerre-type, first order shear deformation shallow shell theory (FSDT), formulated in terms of transverse deflection w, the rotation ψ of the normal to the midsurface and the stress function Φ, are solved by the orthogonal point collocation method. Typical numerical results for static and dynamic buckling loads for FSDT are compared with the classical lamination theory and the dependence of the effect of the shear deformation on the thickness parameter for various boundary conditions is investigated.

  19. Pattern dynamics in an annular CO2 laser

    Ramon, M.L. (M. L.); R. Meucci; Allaria, E.; Boccaletti, S.

    2000-01-01

    Competition among modes in an annular CO2 laser has been experimentally and numerically analyzed. During the coexistence of di erent patterns, each of them resulting from the interaction of two transverse modes with opposite angular momentum, chaos has been experimentally detected. A numerical model, derived from the Maxwell-Bloch equations and including symmetry breaking terms, enables the interpretation of the main experimental features.

  20. Flow of viscoplastic fluids in eccentric annular geometries

    Szabo, Peter; Hassager, Ole

    1992-01-01

    A classification of flowfields for the flow of a Bingham fluid in general eccentric annular geometries is presented. Simple arguments show that a singularity can exist in the stress gradient on boundaries between zones with yielded and un-yielded fluid respectively. A Finite Element code is used...... to verify this property of the Bingham fluid. An analytical solution for the flowfield in case of small eccentricities is derived....

  1. Hydraulic forces caused by annular pressure seals in centrifugal pumps

    Iino, T.; Kaneko, H.

    1980-01-01

    The hydraulic forces caused by annular pressure seals were investigated. The measured inlet and exit loss coefficients of the flow through the seals were much smaller than the conventional values. The results indicate that the damping coefficient and the inertia coefficient of the fluid film in the seal are not affected much by the rotational speed or the eccentricity of the rotor, though the stiffness coefficient seemed to be influenced by the eccentricity.

  2. Allopurinol induced granuloma annulare in a patient of lepromatous leprosy

    Satyendra Kumar Singh

    2013-01-01

    Full Text Available Granuloma annulare (GA is a benign, inflammatory dermatosis involving dermis or subcutis with unknown etiology and poorly understood pathology. GA has characteristic histological features of necrobiosis, granuloma formation and abundant mucin deposition. Various predisposing factors, systemic diseases and drugs have been implicated in the etiology. We hereby describe a case of 70 year old male who was a known case of lepromatous leprosy, taking multidrug therapy for 6 months presented with multiple discrete, annular, firm, non tender, smooth surfaced skin colored papular lesions ranging in size from 0.5-1 cm over back for 1 month. There was past history of intake of allopurinol for hyperuricemia which was started 1 year back. There was history of similar lesions 6 months back which healed within 1 month of stopping allopurinol and he started taking the drug for the past 4 months on his own without any medical advice. Histopathological examination showed superficial and deep perivascular lymphocytic infiltrate with numerous histiocytes scattered in the intersititum of reticular dermis and abundant mucin in between the histiocytes. Allopurinol was implicated as an etiological agent and dramatic improvement was seen after stopping the drug for a period of 4 weeks. Naranjo′s algorithm showed a probable association with a score of 6. Thus the final diagnosis of allopurinol induced generalised interstitial granuolma annulare was made. Patient was advised to continue antileprotic drugs, low purine diet and avoid allopurinol intake.

  3. Standing wave acoustic levitation on an annular plate

    Kandemir, Mehmet Hakan; Çalışkan, Mehmet

    2016-11-01

    In standing wave acoustic levitation technique, a standing wave is formed between a source and a reflector. Particles can be attracted towards pressure nodes in standing waves owing to a spring action through which particles can be suspended in air. This operation can be performed on continuous structures as well as in several numbers of axes. In this study an annular acoustic levitation arrangement is introduced. Design features of the arrangement are discussed in detail. Bending modes of the annular plate, known as the most efficient sound generation mechanism in such structures, are focused on. Several types of bending modes of the plate are simulated and evaluated by computer simulations. Waveguides are designed to amplify waves coming from sources of excitation, that are, transducers. With the right positioning of the reflector plate, standing waves are formed in the space between the annular vibrating plate and the reflector plate. Radiation forces are also predicted. It is demonstrated that small particles can be suspended in air at pressure nodes of the standing wave corresponding to a particular bending mode.

  4. A New Atom Trap The Annular Shell Atom Trap (ASAT)

    Pilloff, H S; Pilloff, Herschel S.; Horbatsch, Marko

    2002-01-01

    In the course of exploring some aspects of atom guiding in a hollow, optical fiber, a small negative potential energy well was found just in front of the repulsive or guiding barrier. This results from the optical dipole and the van der Waals potentials. The ground state for atoms bound in this negative potential well was determined by numerically solving the Schrodinger eq. and it was found that this negative well could serve as an atom trap. This trap is referred to as the Annular Shell Atom Trap or ASAT because of the geometry of the trapped atoms which are located in the locus of points defining a very thin annular shell just in front of the guiding barrier. A unique feature of the ASAT is the compression of the atoms from the entire volume to the volume of the annular shell resulting in a very high density of atoms in this trap. This trap may have applications to very low temperatures using evaporative cooling and possibly the formation of BEC. Finally, a scheme is discussed for taking advantage of the d...

  5. Quantitative annular dark field electron microscopy using single electron signals.

    Ishikawa, Ryo; Lupini, Andrew R; Findlay, Scott D; Pennycook, Stephen J

    2014-02-01

    One of the difficulties in analyzing atomic resolution electron microscope images is that the sample thickness is usually unknown or has to be fitted from parameters that are not precisely known. An accurate measure of thickness, ideally on a column-by-column basis, parameter free, and with single atom accuracy, would be of great value for many applications, such as matching to simulations. Here we propose such a quantification method for annular dark field scanning transmission electron microscopy by using the single electron intensity level of the detector. This method has the advantage that we can routinely quantify annular dark field images operating at both low and high beam currents, and under high dynamic range conditions, which is useful for the quantification of ultra-thin or light-element materials. To facilitate atom counting at the atomic scale we use the mean intensity in an annular dark field image averaged over a primitive cell, with no free parameters to be fitted. To illustrate the potential of our method, we demonstrate counting the number of Al (or N) atoms in a wurtzite-type aluminum nitride single crystal at each primitive cell over the range of 3-99 atoms.

  6. Droplet sizes, dynamics and deposition in vertical annular flow

    Lopes, J C.B.; Dukler, A E

    1985-10-01

    The role of droplets in vertical upwards annular flow is investigated, focusing on the droplet size distributions, dynamics, and deposition phenomena. An experimental program was performed based on a new laser optical technique developed in these laboratories and implemented here for annular flow. This permitted the simultaneous measurement of droplet size, axial and radial velocity. The dependence of droplet size distributions on flow conditions is analyzed. The Upper-Log Normal function proves to be a good model for the size distribution. The mechanism controlling the maximum stable drop size was found to result from the interaction of the pressure fluctuations of the turbulent flow of the gas core with the droplet. The average axial droplet velocity showed a weak dependence on gas rates. This can be explained once the droplet size distribution and droplet size-velocity relationship are analyzed simultaneously. The surprising result from the droplet conditional analysis is that larger droplet travel faster than smaller ones. This dependence cannot be explained if the drag curves used do not take into account the high levels of turbulence present in the gas core in annular flow. If these are considered, then interesting new situations of multiplicity and stability of droplet terminal velocities are encountered. Also, the observed size-velocity relationship can be explained. A droplet deposition is formulated based on the particle inertia control. This permitted the calculation of rates of drop deposition directly from the droplet size and velocities data.

  7. Annular Pulse Shaping Technique for Large-Diameter Kolsky Bar Experiments on Concrete

    2014-10-01

    lt ag e (V ) Time (microsecond) Fig. 5 Linear incident wave generated using an annular copper pulse shaper (O.D. = 25.4 mm, I.D. = 14.4 mm). Note that...AFRL-RW-EG-TP-2014-005 Annular Pulse Shaping Technique for Large- Diameter Kolsky Bar Experiments on Concrete...NUMBER (Include area code) 13-6-2014 Technical Publication October 2012 - February 2014 ANNULAR PULSE SHAPING TECHNIQUE FOR LARGE-DIAMETER KOLSKY BAR

  8. Elastic Properties of the Annular Ligament of the Human Stapes—AFM Measurement

    Kwacz, Monika; Rymuza, Zygmunt; Michałowski, Marcin; Wysocki, Jarosław

    2015-01-01

    Elastic properties of the human stapes annular ligament were determined in the physiological range of the ligament deflection using atomic force microscopy and temporal bone specimens. The annular ligament stiffness was determined based on the experimental load-deflection curves. The elastic modulus (Young’s modulus) for a simplified geometry was calculated using the Kirchhoff–Love theory for thin plates. The results obtained in this study showed that the annular ligament is a linear elastic ...

  9. Pancreaticoduodenectomy for pancreas carcinoma occurring in the annular pancreas: report of a case.

    Kawaida, Hiromichi; Kono, Hiroshi; Watanabe, Mitsuaki; Maki, Akira; Amemiya, Hidetake; Matsuda, Masanori; Fujii, Hideki; Fukasawa, Mitsuharu; Takahashi, Ei; Sano, Katsuhiro; Inoue, Tomohiro

    2015-08-01

    The annular pancreas is a rare congenital anomaly in which a ring of the pancreas parenchyma surrounds the second part of the duodenum. Malignant tumors are extremely rare in patients with an annular pancreas. A 64-year-old man presented with appetite loss and vomiting. Abdominal contrast-enhanced computed tomography (CT) indicated pancreas parenchyma surrounding the second part of the duodenum, and a hypovascular area occupying lesion in the annular pancreas. Subtotal stomach-preserving pancreaticoduodenectomy was performed. Histopathology showed pancreatic carcinoma occurring in the complete annular pancreas.

  10. Links between granuloma annulare, necrobiosis lipoidica diabeticorum and childhood diabetes: a matter of time?

    Davison, James E; Davies, Alison; Moss, Celia; Kirk, Jeremy M W; Taibjee, Saleem M; Agwu, J Chizo

    2010-01-01

    Diabetes mellitus is associated with a range of dermatologic presentations, including granuloma annulare and necrobiosis lipoidica diabeticorum. Granuloma annulare occurs earlier than necrobiosis lipoidica diabeticorum and the association with diabetes mellitus is much weaker. We describe two children with diabetes who both developed granuloma annulare and later, necrobiosis lipoidica diabeticorum. We postulate that the early onset and transient nature of granuloma annulare, compared with the later onset and persistence of necrobiosis lipoidica diabeticorum, might account for the different apparent rates of association with diabetes mellitus.

  11. Electron beam diagnostic system using computed tomography and an annular sensor

    Elmer, John W.; Teruya, Alan T.

    2014-07-29

    A system for analyzing an electron beam including a circular electron beam diagnostic sensor adapted to receive the electron beam, the circular electron beam diagnostic sensor having a central axis; an annular sensor structure operatively connected to the circular electron beam diagnostic sensor, wherein the sensor structure receives the electron beam; a system for sweeping the electron beam radially outward from the central axis of the circular electron beam diagnostic sensor to the annular sensor structure wherein the electron beam is intercepted by the annular sensor structure; and a device for measuring the electron beam that is intercepted by the annular sensor structure.

  12. An Annular Gap Acceleration Model for γ-ray Emission of Pulsars

    2007-01-01

    If the binding energy of the pulsar's surface is not so high (the case of a neutron star), both negative and positive charges will flow out freely from the surface of the star. An annular free flow model for γ-ray emission of pulsars is suggested. It is emphasized that:(1) Two kinds of acceleration regions (annular and core) need to be taken into account. The annular acceleration region is defined by the magnetic field lines that cross the null charge surface within the light cylinder. (2) If the potential drop in the annular region of a pulsar is high enough (normally the case for young pulsars), charges in both the annular and the core regions could be accelerated and produce primary gamma-rays. Secondary pairs are generated in both regions and stream outwards to power the broadband radiations. (3) The potential drop grows more rapidly in the annular region than in the core region. The annular acceleration process is a key process for producing the observed wide emission beams. (4)The advantages of both the polar cap and outer gap models are retained in this model. The geometric properties of the γ-ray emission from the annular flow are analogous to that presented in a previous work by Qiao et al., which match the observations well. (5) Since charges with different signs leave the pulsar through the annular and the core regions respectively, the current closure problem can be partially solved.

  13. Geometry optimization of linear and annular plasma synthetic jet actuators

    Neretti, G.; Seri, P.; Taglioli, M.; Shaw, A.; Iza, F.; Borghi, C. A.

    2017-01-01

    The electrohydrodynamic (EHD) interaction induced in atmospheric air pressure by a surface dielectric barrier discharge (DBD) actuator has been experimentally investigated. Plasma synthetic jet actuators (PSJAs) are DBD actuators able to induce an air stream perpendicular to the actuator surface. These devices can be used in the field of aerodynamics to prevent or induce flow separation, modify the laminar to turbulent transition inside the boundary layer, and stabilize or mix air flows. They can also be used to enhance indirect plasma treatment effects, increasing the reactive species delivery rate onto surfaces and liquids. This can play a major role in plasma processing and chemical kinetics modelling, where often only diffusive mechanisms are considered. This paper reports on the importance that different electrode geometries can have on the performance of different PSJAs. A series of DBD aerodynamic actuators designed to produce perpendicular jets has been fabricated on two-layer printed circuit boards (PCBs). Both linear and annular geometries were considered, testing different upper electrode distances in the linear case and different diameters in the annular one. An AC voltage supplied at a peak of 11.5 kV and a frequency of 5 kHz was used. Lower electrodes were connected to the ground and buried in epoxy resin to avoid undesired plasma generation on the lower actuator surface. Voltage and current measurements were carried out to evaluate the active power delivered to the discharges. Schlieren imaging allowed the induced jets to be visualized and gave an estimate of their evolution and geometry. Pitot tube measurements were performed to obtain the velocity profiles of the PSJAs and to estimate the mechanical power delivered to the fluid. The optimal values of the inter-electrode distance and diameter were found in order to maximize jet velocity, mechanical power or efficiency. Annular geometries were found to achieve the best performance.

  14. Fiber-optic annular detector array for large depth of field photoacoustic macroscopy.

    Bauer-Marschallinger, Johannes; Höllinger, Astrid; Jakoby, Bernhard; Burgholzer, Peter; Berer, Thomas

    2017-03-01

    We report on a novel imaging system for large depth of field photoacoustic scanning macroscopy. Instead of commonly used piezoelectric transducers, fiber-optic based ultrasound detection is applied. The optical fibers are shaped into rings and mainly receive ultrasonic signals stemming from the ring symmetry axes. Four concentric fiber-optic rings with varying diameters are used in order to increase the image quality. Imaging artifacts, originating from the off-axis sensitivity of the rings, are reduced by coherence weighting. We discuss the working principle of the system and present experimental results on tissue mimicking phantoms. The lateral resolution is estimated to be below 200 μm at a depth of 1.5 cm and below 230 μm at a depth of 4.5 cm. The minimum detectable pressure is in the order of 3 Pa. The introduced method has the potential to provide larger imaging depths than acoustic resolution photoacoustic microscopy and an imaging resolution similar to that of photoacoustic computed tomography.

  15. Axisymmetric Natural Frequencies of Statically Loaded Annular Plates

    Eihab M. Abdel-Rahman

    2003-01-01

    Full Text Available We present a numerical procedure to solve the axisymmetric vibration problem of statically loaded annular plates. We use the von Kármán nonlinear plate model to account for large deformations and study the effect of static deflections on the natural frequencies and mode shapes for six combinations of boundary conditions. The shooting method is used to solve the resulting eigenvalue problem. Our results show that static deformations have a significant effect on the natural frequencies and small effect on the mode shapes of the plate. Further, the results show that the presence of in-plane stresses has a significant effect on the natural frequencies.

  16. Coexistence of disseminated granuloma annulare and asymptomatic multiple myeloma

    Şebnem Aktan

    2013-09-01

    Full Text Available Granuloma annulare (GA is a benign inflammatory dermatosis of unknown cause, characterized by necrobiotic dermal papules. Several morphologic forms of GA including localized, disseminated, linear, nodular, perforating, subcutaneous, pustular and arcuate dermal erythema have been reported in the literature. Disseminated GA, a rarely seen form, has been reported in association with some hematopoietic and solid malignancies; however, it has been suggested that the exact causative relationship between malignancy and GA is unclear. We present here a 66-year-old female patient with disseminated GA associated with asymptomatic multipl myeloma.

  17. Histiocytoid Sweet's syndrome presenting with annular erythematous plaques*

    Marcarini, Renata; de Araujo, Raquel Nardelli; Nóbrega, Monisa Martins; Medeiros, Karina Bittencourt; Gripp, Alexandre Carlos; Maceira, Juan Manuel Piñeiro

    2016-01-01

    Histiocytoid Sweet's Syndrome is a rare inflammatory disease described in 2005 as a variant of the classical Sweet's Syndrome (SS). Histopathologically, the dermal inflammatory infiltrate is composed mainly of mononuclear cells that have a histiocytic appearance and represent immature myeloid cells. We describe a case of Histiocytoid Sweet's Syndrome in an 18-year-old man. Although this patient had clinical manifestations compatible with SS, the cutaneous lesions consisted of erythematous annular plaques, which are not typical for this entity and have not been described in histiocytic form so far. The histiocytic subtype was confirmed by histopathological analysis that showed positivity for myeloperoxidase in multiple cells with histiocytic appearance.

  18. Final Technical Report for the MIT Annular Fuel Research Project

    Mujid S. Kazimi; Pavel Hejzlar

    2008-01-31

    MIT-NFC-PR-082 (January 2006) Abstract This summary provides an overview of the results of the U.S. DOE funded NERI (Nuclear Research ENergy Initiative) program on development of the internally and externally cooled annular fuel for high power density PWRs. This new fuel was proposed by MIT to allow a substantial increase in poer density (on the order of 30% or higher) while maintaining or improving safety margins. A comprehensive study was performed by a team consisting of MIT (lead organization), Westinghuse Electric Corporation, Gamma Engineering Corporation, Framatome ANP(formerly Duke Engineering) and Atomic Energy of Canada Limited.

  19. Analysis of Cold Flowfield of Multi—Annular Opposed Jets

    H.F.Zhao; G.C.Benelli

    1992-01-01

    The technique of the use of multi-annular opposed jets as different from using swirl and bluff body creates an excellent recirculation zone with desired size in a large space.The size of ecirculation,the magnitude of reverse velocity and turbulence intensity are much greater than those formed by bluff body.Factors affecting the flowfield include the velocity ration of the opposed jets to the primary air J.the diameter and construction of the opposed jet ring,secondary air velocity and configuration,and confined or unconfined flow condition and so on.This method is a promising way for flame stabilization in combustion technology.

  20. Comparison of superresolution effects with annular phase and amplitude filters.

    Luo, Hongxin; Zhou, Changhe

    2004-12-01

    The characteristics of annular amplitude and phase filters are compared. The behavior of two-zone phase and amplitude filters as the inner zone is increased is studied in detail. Numerical simulations show that a phase filter can achieve a superresolution effect, a circular Dammann effect, and flat-topped intensity for different applications, whereas a two-zone amplitude filter can generate only a superresolution effect. The experimental results show that both amplitude and phase filters can achieve superresolution. Generally, a phase superresolution filter is recommended for its higher efficiency and its special diffraction patterns that are impossible to achieve with an amplitude filter.

  1. Unusual Presentation of Acute Annular Urticaria: A Case Report

    Gilles Guerrier

    2011-01-01

    Full Text Available Acute urticarial lesions may display central clearing with ecchymotic or haemorrhagic hue, often misdiagnosed as erythema multiforme, serum-sickness-like reactions, or urticarial vasculitis. We report a case of acute annular urticaria with unusual presentation occurring in a 20-month-old child to emphasize the distinctive morphologic manifestations in a single disease. Clinicians who care for children should be able to differentiate acute urticaria from its clinical mimics. A directed history and physical examination can reliably orientate necessary diagnostic testing and allow for appropriate treatment.

  2. Portal annular pancreas: a systematic review of a clinical challenge.

    Harnoss, Jonathan M; Harnoss, Julian C; Diener, Markus K; Contin, Pietro; Ulrich, Alexis B; Büchler, Markus W; Schmitz-Winnenthal, Friedrich H

    2014-10-01

    Portal annular pancreas (PAP) is an asymptomatic congenital pancreas anomaly, in which portal and/or mesenteric veins are encased by pancreas tissue. The aim of the study was to determine the role of PAP in pancreatic surgery as well as its management and potential complication, specifically, postoperative pancreatic fistula (POPF).On the basis of a case report, the MEDLINE and ISI Web of Science databases were systematically reviewed up to September 2012. All articles describing a case of PAP were considered.In summary, 21 studies with 59 cases were included. The overall prevalence of PAP was 2.4% and the patients' mean (SD) age was 55.9 (16.2) years. The POPF rate in patients with PAP (12 pancreaticoduodenectomies and 3 distal pancreatectomies) was 46.7% (in accordance with the definition of the International Study Group of Pancreatic Surgery).Portal annular pancreas is a quite unattended pancreatic variant with high prevalence and therefore still remains a clinical challenge to avoid postoperative complications. To decrease the risk for POPF, attentive preoperative diagnostics should also focus on PAP. In pancreaticoduodenectomy, a shift of the resection plane to the pancreas tail should be considered; in extensive pancreatectomy, coverage of the pancreatic remnant by the falciform ligament could be a treatment option.

  3. Non-null annular subaperture stitching interferometry for aspheric test

    Zhang, Lei; Liu, Dong; Shi, Tu; Yang, Yongying; Chong, Shiyao; Miao, Liang; Huang, Wei; Shen, Yibing; Bai, Jian

    2015-10-01

    A non-null annular subaperture stitching interferometry (NASSI), combining the subaperture stitching idea and non-null test method, is proposed for steep aspheric testing. Compared with standard annular subaperture stitching interferometry (ASSI), a partial null lens (PNL) is employed as an alternative to the transmission sphere, to generate different aspherical wavefronts as the references. The coverage subaperture number would thus be reduced greatly for the better performance of aspherical wavefronts in matching the local slope of aspheric surfaces. Instead of various mathematical stitching algorithms, a simultaneous reverse optimizing reconstruction (SROR) method based on system modeling and ray tracing is proposed for full aperture figure error reconstruction. All the subaperture measurements are simulated simultaneously with a multi-configuration model in a ray-tracing program, including the interferometric system modeling and subaperture misalignments modeling. With the multi-configuration model, full aperture figure error would be extracted in form of Zernike polynomials from subapertures wavefront data by the SROR method. This method concurrently accomplishes subaperture retrace error and misalignment correction, requiring neither complex mathematical algorithms nor subaperture overlaps. A numerical simulation exhibits the comparison of the performance of the NASSI and standard ASSI, which demonstrates the high accuracy of the NASSI in testing steep aspheric. Experimental results of NASSI are shown to be in good agreement with that of Zygo® VerifireTM Asphere interferometer.

  4. A compact annular ring microstrip antenna for WSN applications.

    Wang, Daihua; Song, Linli; Zhou, Hanchang; Zhang, Zhijie

    2012-01-01

    A compact annular ring microstrip antenna was proposed for a wireless sensor network (WSN) application in the 2.4 GHz band. In this paper the major considerations of the conformal antenna design were the compact size and the impact on antenna's performance of a steel installation base. By using a chip resistor of large resistance (120 Ω) the antenna size was reduced to 38% of that a conventional annular ring patch antenna. With the addition of the steel installation base the resonant frequency of the antenna increases about 4.2% and the bandwidth reduces from 17.5% to 11.7% by adjusting the load resistance simultaneously. Several key parameters were discussed and optimized, and the antenna was fabricated and its performance measured. The antenna is well matched at 2.4 GHz with 34.2 dB return loss and -2.5 dBi peak gain. Meanwhile, it exhibits excellent radiation patterns with very low cross-polarization levels.

  5. A Compact Annular Ring Microstrip Antenna for WSN Applications

    Daihua Wang

    2012-06-01

    Full Text Available A compact annular ring microstrip antenna was proposed for a wireless sensor network (WSN application in the 2.4 GHz band. In this paper the major considerations of the conformal antenna design were the compact size and the impact on antenna’s performance of a steel installation base. By using a chip resistor of large resistance (120 Ω the antenna size was reduced to 38% of that a conventional annular ring patch antenna. With the addition of the steel installation base the resonant frequency of the antenna increases about 4.2% and the bandwidth reduces from 17.5% to 11.7% by adjusting the load resistance simultaneously. Several key parameters were discussed and optimized, and the antenna was fabricated and its performance measured. The antenna is well matched at 2.4 GHz with 34.2 dB return loss and –2.5 dBi peak gain. Meanwhile, it exhibits excellent radiation patterns with very low cross-polarization levels.

  6. Design Attributes and Scale Up Testing of Annular Centrifugal Contactors

    David H. Meikrantz; Jack D. Law

    2005-04-01

    Annular centrifugal contactors are being used for rapid yet efficient liquid- liquid processing in numerous industrial and government applications. Commercialization of this technology began eleven years ago and now units with throughputs ranging from 0.25 to 700 liters per minute are readily available. Separation, washing, and extraction processes all benefit from the use of this relatively new commercial tool. Processing advantages of this technology include: low in-process volume per stage, rapid mixing and separation in a single unit, connection-in-series for multi-stage use, and a wide operating range of input flow rates and phase ratios without adjustment. Recent design enhancements have been added to simplify maintenance, improve inspection ability, and provide increased reliability. Cartridge-style bearing and mechanical rotary seal assemblies that can include liquid-leak sensors are employed to enhance remote operations, minimize maintenance downtime, prevent equipment damage, and extend service life. Clean-in-place capability eliminates the need for disassembly, facilitates the use of contactors for feed clarification, and can be automated for continuous operation. In nuclear fuel cycle studies, aqueous based separations are being developed that efficiently partition uranium, actinides, and fission products via liquid-liquid solvent extraction. Thus, annular centrifugal contactors are destined to play a significant role in the design of such new processes. Laboratory scale studies using mini-contactors have demonstrated feasibility for many such separation processes but validation at an engineering scale is needed to support actual process design.

  7. Characterization of interfacial waves in horizontal core-annular flow

    Tripathi, Sumit; Bhattacharya, Amitabh; Singh, Ramesh; Tabor, Rico F.

    2016-11-01

    In this work, we characterize interfacial waves in horizontal core annular flow (CAF) of fuel-oil and water. Experimental studies on CAF were performed in an acrylic pipe of 15.5mm internal diameter, and the time evolution of the oil-water interface shape was recorded with a high speed camera for a range of different flow-rates of oil (Qo) and water (Qw). The power spectrum of the interface shape shows a range of notable features. First, there is negligible energy in wavenumbers larger than 2 π / a , where a is the thickness of the annulus. Second, for high Qo /Qw , there is no single dominant wavelength, as the flow in the confined annulus does not allow formation of a preferred mode. Third, for lower Qo /Qw , a dominant mode arises at a wavenumber of 2 π / a . We also observe that the power spectrum of the interface shape depends weakly on Qw, and strongly on Qo, perhaps because the net shear rate in the annulus appears to depend weakly on Qw as well. We also attempt to build a general empirical model for CAF by relating the interfacial stress (calculated via the mean pressure gradient) to the flow rate in the annulus, the annular thickness and the core velocity. Authors are thankful to Orica Mining Services (Australia) for the financial support.

  8. Annular bullous lesions with atypical erythema multiforme in leprosy.

    Shah, Aishani; Mahajan, Rashmi; Ninama, Kishan; Bilimoria, Freny

    2014-09-01

    Erythema nodosum leprosum (ENL) is an immune complex-mediated reaction that may complicate the course of multibacillary leprosy. Bullous lesions in Type II reaction, though reported, are exceedingly rare. We report the case of a 32 year old female patient who presented initially at our OPD with erythema nodosum. Cutaneous examination revealed impaired sensation over dorsum of right foot and thickened right lateral popliteal nerve. Slit skin smear (SSS) from ear lobes revealed AFB with a bacteriological index of 2+. She was started on MDT, tablet ofloxacin 200 mg twice a day, and 30 mg oral prednisolone. Two months later, she presented with generalised pruritus, large target lesions over the back, and hemorrhagic bullae over lower extremities and annular pattern of bullae, over both arms. A SSS was repeated which was positive for AFB. Histopathology from bullous lesions was consistent with ENL. Direct Immunofluorescence (DIF) study was negative. Our patient improved rapidly after she was started on thalidomide 100 mg twice daily, with withdrawal of ofloxacin. Erythema Multiforme (EMF) and annular bullous lesions have been reported in patients on treatment with ofloxacin. This case is being presented due to the unusual and varied manifestation of Type II lepra reaction in a 34 year old female patient.

  9. Droplet entrainment rate in gas-liquid annular flow

    Sawant, P. [Energy Research Inc., Rockville, Maryland (United States); Liu, Y.; Ishii, M. [Purdue Univ., West Lafayette, Indiana (United States); Mori, M. [Tokyo Electric Power Co., Inc., Yokohama (Japan); Chen, S. [Purdue Univ., West Lafayette, Indiana (United States)

    2011-07-01

    Droplet entrainment and deposition are the two most important physical phenomena in the gas-liquid annular two-phase flow. Modeling of these phenomena is essential for the estimation of dryout margins in the Light Water Reactors (LWRs) and the boilers. In this study, gas-liquid annular two-phase flow experiments are performed in a vertical round tube test section under adiabatic conditions. Air-water and organic fluid Freon-113 are used as the test fluids. The experiments covered a wide range of pressure and flow conditions. Liquid film extraction technique was used for the measurement of droplet entrainment and deposition rates. Additionally, the thickness of liquid film was measured in the air-water experiments using the ring type conductance probes. In this paper, the experimental data on entrainment rate is used to analyze the currently available correlations in the literature. The analysis showed that the existing correlations failed to predict the data at high gas velocity conditions. At high gas velocity, the experimental entrainment rate approaches a maximum limiting value; however, the correlations predicted continuously increasing entrainment rate as the gas velocity increases. (author)

  10. Electroactive liquid lens driven by an annular membrane.

    Wei, Kang; Domicone, Nicholas Wade; Zhao, Yi

    2014-03-01

    Unlike traditional focalization that recruits multiple moving lens elements to adjust focus, liquid lenses deliver adaptive focusing by simply tuning the surface profile of liquid or the elastomer that encloses liquid. Its simple and compact configuration, low cost, and actuation efficiency promise wide industrial, medical, and consumer applications. Dielectric elastomers (DEs), one type of commercially available soft active material, have been a good fit for creating adaptive optics. In this Letter, we present an adaptive, membrane-sealed liquid lens hydrostatically coupled to a concentric annular DE actuator. Electric actuation deforms the annular DE, which induces fluid transmission between the lens part and the actuation part for lens actuation. The maximum measured focal range was from 25.4 to 105.2 mm within 1.0 kV, which significantly outperforms the existing DE-actuated liquid lenses and eliminates the need for prestraining. The lens also enables varied focal ranges by simply adjusting its initial surface sagitta, providing flexibility for practical imaging applications.

  11. Maximizing prosthetic valve size with the Top Hat supra-annular aortic valve

    Aagaard, Jan; Geha, Alexander S.

    2007-01-01

    BACKGROUND AND AIM OF THE STUDY: The CarboMedics Top Hat supra-annular aortic valve allows a one-size (and often two-size) increase over the standard intra-annular valve. This advantage should minimize the risk of patient-prosthesis mismatch, where the effective prosthetic valve orifice area...

  12. Simultaneous occurrence of ulcerated necrobiosis lipoidica and granuloma annulare in a patient: case report.

    Souza, Fernanda Homem de Mello de; Ribeiro, Camila Ferrari; Pereira, Marcela Abou Chami; Mesquita, Lismary; Fabrício, Lincoln

    2011-01-01

    Simultaneous occurrence of granuloma annulare and necrobiosis lipoidica is quite rare. There are seven reported cases in the literature, but only one presenting ulcerated necrobiosis lipoidica. We report a 39-year-old male with histopathologically confirmed granuloma annulare and ulcerated necrobiosis lipoidica, without diabetes mellitus.

  13. Design and characterization of the annular cathode high current pulsed electron beam source for circular components

    Jiang, Wei; Wang, Langping, E-mail: aplpwang@hit.edu.cn; Wang, Xiaofeng

    2016-08-01

    Highlights: • An annular cathode for HCPEB irradiation of circular components was designed. • The processing window for the annular cathode is obtained. • Irradiation thickness uniformity along the circumferential direction exceeds 90%. - Abstract: In order to irradiate circular components with high current pulsed electron beam (HCPEB), an annular cathode based on carbon fiber bunches was designed and fabricated. Using an acceleration voltage of 25 kV, the maximum pulsed irradiation current and energy of this annular cathode can reach 7.9 kA and 300 J, respectively. The irradiation current density distribution of the annular cathode HCPEB source measured along the circumferential direction shows that the annular cathode has good emission uniformity. In addition, four 9310 steel substrates fixed uniformly along the circumferential direction of a metal ring substrate were irradiated by this annular cathode HCPEB source. The surface and cross-section morphologies of the irradiated samples were characterized by scanning electron microscopy (SEM). SEM images of the surface reveal that crater and surface undulation have been formed, which hints that the irradiation energy of the HCPEB process is large enough for surface modification of 9310 steel. Meanwhile, SEM cross-section images exhibit that remelted layers with a thickness of about 5.4 μm have been obtained in all samples, which proves that a good practical irradiation uniformity can be achieved by this annular cathode HCPEB source.

  14. Erythema annulare centrifugum as presenting sign of activation of breast cancer*

    Topal, Ilteris Oguz; Topal, Yunus; Sargan, Aytul; Duman, Hatice; Gungor, Sule; Goncu, Ozgur Emek Kocaturk; Ozekinci, Selver

    2015-01-01

    Erythema annulare centrifugum is a figurate erythema of unknown etiology. It has been associated with many different entities, including infections, food allergy, drug reactions and malignant neoplasms. Herein, we report a case of erythema annulare centrifugum as presenting sign of activation of breastcancer. PMID:26734884

  15. Erythema annulare centrifugum as presenting sign of activation of breast cancer.

    Topal, Ilteris Oguz; Topal, Yunus; Sargan, Aytul; Duman, Hatice; Gungor, Sule; Goncu, Ozgur Emek Kocaturk; Ozekinci, Selver

    2015-01-01

    Erythema annulare centrifugum is a figurate erythema of unknown etiology. It has been associated with many different entities, including infections, food allergy, drug reactions and malignant neoplasms. Herein, we report a case of erythema annulare centrifugum as presenting sign of activation of breastcancer.

  16. Annular Lichenoid Dermatitis of Youth: A Chronic Case Managed Using Pimecrolimus.

    Malachowski, Stephen J; Creasey, Mackenzie; Kinkley, Nancy; Heaphy, Michael R

    2016-11-01

    Annular lichenoid dermatitis of youth, first described in 2003, is a rare and occasionally chronic skin disease. We report a case of annular lichenoid dermatitis of youth relapsing over the course of 5 years successfully treated and maintained with topical pimecrolimus cream.

  17. Core-annular flow through a horizontal pipe: Hydrodynamic counterbalancing of buoyancy force on core

    Ooms, G.; Vuik, C.; Poesio, P.

    2007-01-01

    A theoretical investigation has been made of core-annular flow: the flow of a high-viscosity liquid core surrounded by a low-viscosity liquid annular layer through a horizontal pipe. Special attention is paid to the question of how the buoyancy force on the core, caused by a density difference betwe

  18. Annular core liquid-salt cooled reactor with multiple fuel and blanket zones

    Peterson, Per F.

    2013-05-14

    A liquid fluoride salt cooled, high temperature reactor having a reactor vessel with a pebble-bed reactor core. The reactor core comprises a pebble injection inlet located at a bottom end of the reactor core and a pebble defueling outlet located at a top end of the reactor core, an inner reflector, outer reflector, and an annular pebble-bed region disposed in between the inner reflector and outer reflector. The annular pebble-bed region comprises an annular channel configured for receiving pebble fuel at the pebble injection inlet, the pebble fuel comprising a combination of seed and blanket pebbles having a density lower than the coolant such that the pebbles have positive buoyancy and migrate upward in said annular pebble-bed region toward the defueling outlet. The annular pebble-bed region comprises alternating radial layers of seed pebbles and blanket pebbles.

  19. Fabrication, characterization and applications of flexible vertical InGaN micro-light emitting diode arrays.

    Tian, Pengfei; McKendry, Jonathan J D; Gu, Erdan; Chen, Zhizhong; Sun, Yongjian; Zhang, Guoyi; Dawson, Martin D; Liu, Ran

    2016-01-11

    Flexible vertical InGaN micro-light emitting diode (micro-LED) arrays have been fabricated and characterized for potential applications in flexible micro-displays and visible light communication. The LED epitaxial layers were transferred from initial sapphire substrates to flexible AuSn substrates by metal bonding and laser lift off techniques. The current versus voltage characteristics of flexible micro-LEDs degraded after bending the devices, but the electroluminescence spectra show little shift even under a very small bending radius 3 mm. The high thermal conductivity of flexible metal substrates enables high thermal saturation current density and high light output power of the flexible micro-LEDs, benefiting the potential applications in flexible high-brightness micro-displays and high-speed visible light communication. We have achieved ~40 MHz modulation bandwidth and 120 Mbit/s data transmission speed for a typical flexible micro-LED.

  20. 10-kilowatt photovoltaic concentrator array fabrication

    Sanders, J.A.; Donovan, R.L.; Broadbent, S.

    1980-12-01

    The PCA is based on the use of an acrylic Fresnel lens to concentrate sunlight on high intensity solar cells. The array with modified heat sinks was fabricated to determine the impact on electrical performance due to lower weight heat sinks and reduced thermal dissipation surfaces. The array with modified heat sinks was fabricated to determine the impact on electrical performance due to lower weight heat sinks and reduced thermal dissipation surfaces. The array fabrication proceeded with normal problems expected of preproduction prototypes. Three major problems occurred in the areas of the dimensional adequacy of the environmental housing for the Photovoltaic Modules, the cell/substrate assembly and the azimuth drive structural integrity. The cost optimization study identified a new lower weight heat sink design that would reduce the heat sink weight by 50% and the array cost by approximately 3.1% for a loss of only 7% in annularized electrical power generation. The production cost estimate provides an indicator that an overall 87% learning curve can be achieved and the cost of the 5000th unit could be $5.30 per watt in 1979 dollars. System level costs were also developed to project a busbar energy cost for a 10 MW system produced at the 500th unit. This system would provide energy at 24 cents per kilowatt hour average over a 30 year projected life. As a result of wind tunnel tests and the fabrication experience, an array has been designed for production. The key elements of the redesign are discussed. (MHR)

  1. Intermittent Flow of Granular Matter in an Annular Geometry

    Brzinski, Ted; Daniels, Karen E.

    Granular solids can be subjected to a finite stress below which the response is elastic. Above this yield stress, however, the material fails catastrophically, undergoing a rapid plastic deformation. In the case of a monotonically increasing stress the material exhibits a characteristic stick-slip response. We investigate the statistics of this intermittent failure in an annular shear geometry, driven with a linear-ramp torque in order to generate the stick-slip behavior. The apparatus is designed to allow visual access to particle trajectories and inter-particle forces (through the use of photoelastic materials). Additionally, twelve piezoelectric sensors at the outer wall measure acoustic emissions due to the plastic deformation of the material. We vary volume fraction, and use both fixed and deformable boundaries. We measure how the distribution of slip size and duration are related to the bulk properties of the packing, and compare to systems with similar governing statistics.

  2. Dynamic Response of Three-Layered Annular Plate with Imperfections

    Pawlus Dorota

    2015-02-01

    Full Text Available This paper presents the imperfection sensitivity of annular plate with three-layered structure. The plate composed of thin elastic facings and a thicker elastic core is loaded in facing plane. The classical issue of a three-layered plate was solved for dynamic deflection problem using the approximation methods: orthogonalization and finite difference. The solution includes the axisymmetric and asymmetric plate modes of the dynamic stability loss. The evaluation of the rate of plate sensitivity to imperfection of plate preliminary geometry has been enriched by the analysis of plate models built of finite elements. The ABAQUS program has been used. The numerous calculation results in the form of deflection characteristics, buckling modes, values of critical parameters create the view of response of dynamic plate structure with different rate of imperfection and linear in time loading growth, too.

  3. Fast High Capacity Annular Gas Puff Valve Design Concept

    Ruden, Edward

    2000-10-01

    A fast opening gas valve design concept is presented that can theoretically inject a few grams of D2 gas radially outward into a coaxial annular vacuum region with a radius of about 10 cm in less that 100 μ s. The concept employs a single turn 20-30 T pulsed magnetic field coil that axially accelerates an Mg alloy ring, which seals a gas plenum, to high velocity, releasing the gas. Both coil and ring are profiled to minimize stress in the ring. Such a device could be used to supply the initial gas load for a proposed 5 MJ Dense Plasma Focus driven by AFRL's Shiva Star Capacitor bank. The intent here is keep the vacuum current feed insulator under high vacuum during the discharge to avoid surface breakdown. Alternatively, a high energy rep ratable plasma flow opening switch could be supplied with such a valve. This work is funded by the USAF.

  4. Two-phase flow instabilities in a vertical annular channel

    Babelli, I.; Nair, S.; Ishii, M. [Purdue Univ., West Lafayette, IN (United States)

    1995-09-01

    An experimental test facility was built to study two-phase flow instabilities in vertical annular channel with emphasis on downward flow under low pressure and low flow conditions. The specific geometry of the test section is similar to the fuel-target sub-channel of the Savannah River Site (SRS) Mark 22 fuel assembly. Critical Heat Flux (CHF) was observed following flow excursion and flow reversal in the test section. Density wave instability was not recorded in this series of experimental runs. The results of this experimental study show that flow excursion is the dominant instability mode under low flow, low pressure, and down flow conditions. The onset of instability data are plotted on the subcooling-Zuber (phase change) numbers stability plane.

  5. Stability of Three-Layered Annular Plate with Composite Facings

    Pawlus, D.

    2017-02-01

    Paper presents the behaviour of three-layered annular plates subjected to loads acting in plate plane. Plates are composed of laminated fibre-reinforced composite facings and foam core. The static and dynamic parameters of plate critical state were evaluated. The sensitivity of composite structure of plate to the acting of quickly increasing in time loads is shown. The problem has been solved numerically using the finite element method. Results have been compared with ones obtained for plate models with isotropic layers. These plate models have also been calculated solving formulated task analytically and numerically by means of the finite difference method. Solutions to the problem concern the axisymmetrical and asymmetrical plate buckling modes. Numerous presented tables and figures create the image of the stability behaviour of examined composite plates.

  6. A Novel Design of Magnetorheological Damper with Annular Radial Channel

    Shisha Zhu

    2016-01-01

    Full Text Available With the development of automotive vibration technology, the semiactive suspension system with adjustable damping force and high reliability is taken seriously. The magnetorheological damper (MRD that applies intelligent material (magnetorheological fluid is the key element of this system. It can achieve a continuous and adjustable damping and then reaches the purpose of comfort. In order to improve the damping effect of MRD, this paper presents a MRD, which has magnetorheological (MR effect along annular radial channel. The paper completely designs the structure and magnetic circuit of MRD. Based on the theory of electromagnetism and MR fluid dynamics, the paper analyzes and tests the external characteristics of the MRD by the MATLAB/Simulink and the vibration experiment. The results compared with ordinary MRD reveal that the damping force obviously increases and has wide adjustable range, thus verifying the reasonableness of the damper design.

  7. Development of annular targets for {sup 99}MO production.

    Conner, C.; Lewandowski, E. F.; Snelgrove, J. L.; Liberatore, M. W.; Walker, D. E.; Wiencek, T. C.; McGann, D. J.; Hofman, G. L.; Vandegrift, G. F.

    1999-09-30

    The new annular target performed well during irradiation. The target is inexpensive and provides good heat transfer during irradiation. Based on these and previous tests, we conclude that targets with zirconium tubes and either nickel-plated or zinc-plated foils work well. We proved that we could use aluminum target tubes, which are much cheaper and easier to work with than the zirconium tubes. In aluminum target tubes nickel-plated fission-recoil barriers work well and prevent bonding of the foil to the new target tubes during irradiation. Also, zinc-plated and aluminum-foil barriers appear promising in anodized aluminum tubes. Additional tests are anticipated to address such issues as fission-recoil barrier thickness and uranium foil composition. Overall, however, the target was successful and will provide an inexpensive, efficient way to irradiate LEU metal foil for the production of {sup 99}Mo.

  8. Annular elastolytic giant cell granuloma of conjunctiva: A case report

    Karabi Konar

    2014-01-01

    Full Text Available Annular elastolytic giant cell granuloma is a condition characterized histologically by damaged elastic fibers associated with preponderance of giant cells along with absence of necrobiosis, lipid, mucin, and pallisading granuloma. It usually occurs on sun-damaged skin and hence the previous name actinic granuloma. A similar process occurs on the conjunctiva. Over the past three decades only four cases of conjunctival actinic granuloma have been documented. All the previous patients were females with lesions in nasal or temporal bulbar conjunctiva varying 2-3 mm in size. We report a male patient aged 70 years presenting with a 14 mm × 7 mm fleshy mass on right lower bulbar conjunctiva. Clinical differential diagnoses were lymphoma, squamous cell carcinoma in situ and amyloidosis. Surgical excision followed by histopathology confirmed it to be a case of actinic granuloma. This is the first case of isolated conjunctival actinic granuloma of such a large size reported from India.

  9. Fluxons in long and annular intrinsic Josephson junction stacks

    Clauss, T.; Oehmichen, V.; Mößle, M.; Müller, A.; Weber, A.; Koelle, D.; Kleiner, R.

    2002-12-01

    A promising approach towards a THz oscillator based on intrinsic Josephson junctions in high-temperature superconductors is based on the collective motion of Josephson fluxons, which are predicted to form various configurations ranging from a triangular to a quadratic lattice. Not only for this reason, but certainly also for the sake of basic physics, several experimental and theoretical investigations have been done on the subject of collective fluxon dynamics in stacked intrinsic Josephson junctions. In this paper we will present some experimental results on the fluxon dynamics of long intrinsic Josephson junction stacks made of Bi2Sr2CaCu2O8. The stacks were formed either in an open or in an annular geometry, and clear resonant fluxon modes were observed. Experiments discussed include measurements of current-voltage characteristics in external magnetic fields and in external microwave fields.

  10. Geometry-Driven Folding of a Floating Annular Sheet.

    Paulsen, Joseph D; Démery, Vincent; Toga, K Buğra; Qiu, Zhanlong; Russell, Thomas P; Davidovitch, Benny; Menon, Narayanan

    2017-01-27

    Predicting the large-amplitude deformations of thin elastic sheets is difficult due to the complications of self contact, geometric nonlinearities, and a multitude of low-lying energy states. We study a simple two-dimensional setting where an annular polymer sheet floating on an air-water interface is subjected to different tensions on the inner and outer rims. The sheet folds and wrinkles into many distinct morphologies that break axisymmetry. These states can be understood within a recent geometric approach for determining the gross shape of extremely bendable yet inextensible sheets by extremizing an appropriate area functional. Our analysis explains the remarkable feature that the observed buckling transitions between wrinkled and folded shapes are insensitive to the bending rigidity of the sheet.

  11. Performance of annular flow sterilizer irradiated by a germicidal lamp

    Sugawara, T.; Yoneya, M.; Ohashi, H. (Akita Univ. (Japan))

    1981-10-01

    Theoretical and experimental studies were conducted on the UV-inactivation characteristics of Bacillus subtilis spores in an annular-flow sterilizer irradiated by a germicidal lamp located at the center of the inner tube. Experimental results for sterilizer performance in laminar spore-suspension flow were well simulated dynamically and statically by theoretical considerations which incorporated multi-targets with single-hit model for the UV-inactivation kinetic and the diffuse light model for the angle characteristic of lamp, along with due attention to the parabolic velocity distribution and the negligible diffusion of spores. Scale on the outside wall of the inner tube was checked by the use of a cylindrical chemical actinometer. Calculated examples elucidate the reason why careful inspection is needed of UV-inactivation kinetics, angle characteristics of lamp, and fluid mixing to evaluate performance of actual flow UV sterilizers at high extent of inactivation up to the order of 99.999%.

  12. Design of an Annular Disc Subject to Thermomechanical Loading

    Sergei Alexandrov

    2012-01-01

    Full Text Available Two solutions to design a thin annular disc of variable thickness subject to thermomechanical loading are proposed. It is assumed that the thickness of the disc is everywhere sufficiently small for the stresses to be averaged through the thickness. The state of stress is plane. The initiation of plastic yielding is controlled by Mises yield criterion. The design criterion for one of the solutions proposed requires that the distribution of stresses is uniform over the entire disc. In this case there is a relation between optimal values of the loading parameters at the final stage. The specific shape of the disc corresponds to each pair of such parameters. The other solution is obtained under the additional requirement that the distribution of strains is uniform. This solution exists for the disc of constant thickness at specific values of the loading parameters.

  13. Distinct annular oligomers captured along the assembly and disassembly pathways of transthyretin amyloid protofibrils.

    Ricardo H Pires

    Full Text Available BACKGROUND: Defects in protein folding may lead to severe degenerative diseases characterized by the appearance of amyloid fibril deposits. Cytotoxicity in amyloidoses has been linked to poration of the cell membrane that may involve interactions with amyloid intermediates of annular shape. Although annular oligomers have been detected in many amyloidogenic systems, their universality, function and molecular mechanisms of appearance are debated. METHODOLOGY/PRINCIPAL FINDINGS: We investigated with high-resolution in situ atomic force microscopy the assembly and disassembly of transthyretin (TTR amyloid protofibrils formed of the native protein by pH shift. Annular oligomers were the first morphologically distinct intermediates observed in the TTR aggregation pathway. Morphological analysis suggests that they can assemble into a double-stack of octameric rings with a 16 ± 2 nm diameter, and displaying the tendency to form linear structures. According to light scattering data coupled to AFM imaging, annular oligomers appeared to undergo a collapse type of structural transition into spheroid oligomers containing 8-16 monomers. Disassembly of TTR amyloid protofibrils also resulted in the rapid appearance of annular oligomers but with a morphology quite distinct from that observed in the assembly pathway. CONCLUSIONS/SIGNIFICANCE: Our observations indicate that annular oligomers are key dynamic intermediates not only in the assembly but also in the disassembly of TTR protofibrils. The balance between annular and more compact forms of aggregation could be relevant for cytotoxicity in amyloidogenic disorders.

  14. On the Motion of an Annular Film in Microgravity Gas-Liquid Flow

    McQuillen, John B.

    2002-01-01

    Three flow regimes have been identified for gas-liquid flow in a microgravity environment: Bubble, Slug, and Annular. For the slug and annular flow regimes, the behavior observed in vertical upflow in normal gravity is similar to microgravity flow with a thin, symmetrical annular film wetting the tube wall. However, the motion and behavior of this film is significantly different between the normal and low gravity cases. Specifically, the liquid film will slow and come to a stop during low frequency wave motion or slugging. In normal gravity vertical upflow, the film has been observed to slow, stop, and actually reverse direction until it meets the next slug or wave.

  15. Characterization of annular two-phase gas-liquid flows in microgravity

    Bousman, W. Scott; Mcquillen, John B.

    1994-01-01

    A series of two-phase gas-liquid flow experiments were developed to study annular flows in microgravity using the NASA Lewis Learjet. A test section was built to measure the liquid film thickness around the perimeter of the tube permitting the three dimensional nature of the gas-liquid interface to be observed. A second test section was used to measure the film thickness, pressure drop and wall shear stress in annular microgravity two-phase flows. Three liquids were studied to determine the effects of liquid viscosity and surface tension. The result of this study provide insight into the wave characteristics, pressure drop and droplet entrainment in microgravity annular flows.

  16. An analytical model for annular flow boiling heat transfer in microchannel heat sinks

    Megahed, A.; Hassan, I. [Concordia University, Montreal, QC (Canada). Dept. of Mechanical and Industrial Engineering

    2009-07-01

    An analytical model has been developed to predict flow boiling heat transfer coefficient in microchannel heat sinks. The new analytical model is proposed to predict the two-phase heat transfer coefficient during annular flow regime based on the separated model. Opposing to the majority of annular flow heat transfer models, the model is based on fundamental conservation principles. The model considers the characteristics of microchannel heat sink during annular flow and eliminates using any empirical closure relations. Comparison with limited experimental data was found to validate the usefulness of this analytical model. The model predicts the experimental data with a mean absolute error 8%. (author)

  17. Tight focus of a radially polarized and amplitudemodulated annular multi-Gaussian beam

    Chen Jian-Nong; Xu Qin-Feng; Wang Gang

    2011-01-01

    The focusing of a radially polarized beam without annular apodization ora phase filter at the entrance pupil of the objective results in a wide focus and low purity of the longitudinally polarized component.However,the presence of a physical annular apodization or phase filter makes some applications more difficult or even impossible.We propose a radially polarized and amplitude-modulated annular multi-Gaussian beam mode.Numerical simulation shows that it can be focused into a sharper focal spot of 0.125λ2 without additional apodizations or filters.The beam quality describing the purity of longitudinally polarized component is up to 86%.

  18. High-power test of annular-ring coupled structures for the J-PARC linac energy upgrade

    Tamura, Jun; Ao, Hiroyuki; Nemoto, Yasuo; Asano, Hiroyuki; Suzuki, Takahiro

    2015-02-01

    Annular-ring coupled structures (ACSs) will increase the beam energy of the Japan proton accelerator research complex (J-PARC) linac from 181 to 400 MeV to achieve a beam power of 1 MW for a materials and life science experimental facility. The mass production of the ACS cavities commenced in March 2009. Before the installation, all cavities require power testing. High-power testing is essential not only for confirming the cavity's design performance but also for preventing delays in cavity conditioning schedule. However, the 2011 Tohoku earthquake damaged J-PARC facilities, including the ACS power-test area, and cavity conditioning was interrupted for two years. After the facility's restoration, two ACS cavities (M01 and M11) were conditioned. They performed 15-20% above the designed accelerating field of 4.2 MV/m. As M01 was initially conditioned six years ago, the most recent conditioning time required for M01 was drastically reduced. From this result, we confirmed that long-term stored ACS cavities purged with nitrogen gas do not produce critical cavity performance issues. During high-power operation of M11, which is a unique cavity equipped with a capacitive iris in a waveguide, no significant increases in the temperature and the discharge rate around the capacitive iris were observed. Even considering beam loss due to residual gas scattering, the vacuum pressure was sufficiently low (4 × 10-6 Pa). More stable operation can be expected following a month-long conditioning process before the beam is commissioned. M11's conditioning successfully demonstrated an auto-conditioning program, and we established the conditioning scheme using this auto-conditioning program for all ACS cavities in a limited time and with limited manpower.

  19. Biofilm Community Dynamics in Bench-Scale Annular Reactors Simulating Arrestment of Chloraminated Drinking Water Nitrification

    Annular reactors (ARs) were used to study biofilm community succession and provide an ecological insight during nitrification arrestment through simultaneously increasing monochloramine (NH2Cl) and chlorine to nitrogen mass ratios, resulting in four operational periods (I to IV)....

  20. An iterative method for the solution of nonlinear systems using the Faber polynomials for annular sectors

    Myers, N.J. [Univ. of Durham (United Kingdom)

    1994-12-31

    The author gives a hybrid method for the iterative solution of linear systems of equations Ax = b, where the matrix (A) is nonsingular, sparse and nonsymmetric. As in a method developed by Starke and Varga the method begins with a number of steps of the Arnoldi method to produce some information on the location of the spectrum of A. This method then switches to an iterative method based on the Faber polynomials for an annular sector placed around these eigenvalue estimates. The Faber polynomials for an annular sector are used because, firstly an annular sector can easily be placed around any eigenvalue estimates bounded away from zero, and secondly the Faber polynomials are known analytically for an annular sector. Finally the author gives three numerical examples, two of which allow comparison with Starke and Varga`s results. The third is an example of a matrix for which many iterative methods would fall, but this method converges.

  1. Effect of January 15, 2010 annular solar eclipse on meteorological parameters over Goa, India

    Muraleedharan, P.M.; Nisha, P.G.; Mohankumar, K.

    Atmospheric perturbations due to the annular solar eclipse were monitored to understand its influence on the meteorological parameters from surface to the lower stratosphere. A strong inversion at 13 km and an abnormal warming in the upper...

  2. Annular lichenoid dermatitis of youth--a further case in a 12-year-old girl.

    Kleikamp, Stefanie; Kutzner, Heinz; Frosch, Peter J

    2008-08-01

    Annular lichenoid dermatitis of youth was first described by Annessi et al. in 2003. Clinical criteria are persistent erythematous macules and annular lesions with a red-brown edge and a central hypopigmentation usually found on the flanks and groins of children and adolescents. Histologically, the disease is characterized by a lichenoid interface dermatitis with necrotic keratinocytes at the tip of the rete ridges. In our case a 12-year old girl developed annular red-brown macules with papules at the borders in an inframammary location. The histology of the lesion's border showed a lichenoid lymphocytic infiltrate with apoptotic keratinocytes at the tip of rete ridges. The lesions cleared with 0.03% tacrolimus ointment. Annular lichenoid dermatitis of youth is probably a new entity in the group of lichenoid dermatoses.

  3. Design of radial phononic crystal using annular soft material with low-frequency resonant elastic structures

    Gao, Nansha; Wu, Jiu Hui; Yu, Lie; Xin, Hang

    2016-10-01

    Using FEM, we theoretically study the vibration properties of radial phononic crystal (RPC) with annular soft material. The band structures, transmission spectra, and displacement fields of eigenmode are given to estimate the starting and cut-off frequency of band gaps. Numerical calculation results show that RPC with annular soft material can yield low-frequency band gaps below 350 Hz. Annular soft material decreases equivalent stiffness of the whole structure effectively, and makes corresponding band gaps move to the lower frequency range. Physical mechanism behind band gaps is the coupling effect between long or traveling wave in plate matrix and the vibrations of corrugations. By changing geometrical dimensions of plate thickness e, the length of silicone rubber h2, and the corrugation width b, we can control the location and width of the first band gap. These research conclusions of RPC structure with annular soft material can potentially be applied to optimize band gaps, generate filters, and design acoustic devices.

  4. Instability of Annular Beam with Finite Thickness in Dielectric-Loaded Cylindrical Waveguide

    Tamura, Shusuke; Yamakawa, Mitsuhisa; Takashima, Yusuke; Ogura, Kazuo

    2008-01-01

    The cherenkov and slow cyclotron instabilities driven by an axially injected electron beam in a cylindrical waveguide are studied using a new version of the self-consistent linear theory considering three-dimensional beam perturbations. There are three kinds of models for beam instability analysis, which are based on a cylindrical solid beam, an infinitesimally thin annular beam, and a finitely thick annular beam. Among these models, the beam shape properly representing the often used actual ...

  5. Non-approximate method for designing annular field of two-mirror concentric system

    Yuanshen Huang; Dongyue Zhu; Baicheng Li; Dawei Zhang; Zhengji Ni; Songlin Zhuang

    2012-01-01

    Annular field aberrations of a three-reflection concentric system, which are composed of two spherical mirrors, are analyzed. An annular field with a high level of aberration correction exists near the position where the principal ray is perpendicular to the object-image plane. Aberrations are determined by the object height and aperture angle. In this letter, the general expression of the system aberration is derived using the geometric method, and the non-approximate design method is proposed to calculate the radii of the annular fields that have minimum aberrations under different aperture angles. The closer to 0.5 (the ratio of the radius of convex mirror to the radius of concave mirror) is, the smaller the system aberration is. The examples analyzed by LABVIEW indicate that the annular field designed by the proposed method has the smallest aberration in a given system.%Annular field aberrations of a three-reflection concentric system,which are composed of two spherical mirrors,are analyzed.An annular field with a high level of aberration correction exists near the position where the principal ray is perpendicular to the object-image plane.Aberrations are determined by the object height and aperture angle.In this letter,the general expression of the system aberration is derived using the geometric method,and the non-approximate design method is proposed to calculate the radii of the annular fields that have minimum aberrations under different aperture angles.The closer to 0.5 (the ratio of the radius of convex mirror to the radius of concave mirror) is,the smaller the system aberration is.The examples analyzed by LABVIEW indicate that the annular field designed by the proposed method has the smallest aberration in a given system.

  6. Predictors of right ventricular function as measured by tricuspid annular plane systolic excursion in heart failure

    Kjaergaard, Jesper; Iversen, Kasper K; Akkan, Dilek

    2009-01-01

    motion index scores, atrio-ventricular annular plane systolic excursion of the mitral annulus were significantly related to TAPSE. Septal and posterior mitral annular plane systolic excursion (beta = 0.56, p ... in heart failure patients, in particular with reduced septal longitudinal motion. TAPSE is decreased in patients with heart failure of ischemic etiology. However, the absolute reduction in TAPSE is small and seems to be of minor importance in the clinical utilization of TAPSE whether applied as a measure...

  7. Design and analysis of 19 pin annular fuel rod cluster for pressure tube type boiling water reactor

    Deokule, A.P., E-mail: abhijit.deokule1986@gmail.com [Homi Bhabha National Institute, Trombay 400 085, Mumbai (India); Vishnoi, A.K.; Dasgupta, A.; Umasankari, K.; Chandraker, D.K.; Vijayan, P.K. [Bhabha Atomic Research Centre, Trombay 400 085, Mumbai (India)

    2014-09-15

    Highlights: • Development of 19 pin annular fuel rod cluster. • Reactor physics study of designed annular fuel rod cluster. • Thermal hydraulic study of annular fuel rod cluster. - Abstract: An assessment of 33 pin annular fuel rod cluster has been carried out previously for possible use in a pressure tube type boiling water reactor. Despite the benefits such as negative coolant void reactivity and larger heat transfer area, the 33 pin annular fuel rod cluster is having lower discharge burn up as compared to solid fuel rod cluster when all other parameters are kept the same. The power rating of this design cannot be increased beyond 20% of the corresponding solid fuel rod cluster. The limitation on the power is not due to physics parameters rather it comes from the thermal hydraulics side. In order to increase power rating of the annular fuel cluster, keeping same pressure tube diameter, the pin diameter was increased, achieving larger inside flow area. However, this reduces the number of annular fuel rods. In spite of this, the power of the annular fuel cluster can be increased by 30% compared to the solid fuel rod cluster. This makes the nineteen pin annular fuel rod cluster a suitable option to extract more power without any major changes in the existing design of the fuel. In the present study reactor physics and thermal hydraulic analysis carried out with different annular fuel rod cluster geometry is reported in detail.

  8. Annular structures as intermediates in fibril formation of Alzheimer Abeta17-42.

    Zheng, Jie; Jang, Hyunbum; Ma, Buyong; Nussinov, Ruth

    2008-06-05

    We report all-atom molecular dynamics simulations of annular beta-amyloid (17-42) structures, single- and double-layered, in solution. We assess the structural stability and association force of Abeta annular oligomers associated through different interfaces, with a mutated sequence (M35A), and with the oxidation state (M35O). Simulation results show that single-layered annular models display inherent structural instability: one is broken down into linear-like oligomers, and the other collapses. On the other hand, a double-layered annular structure where the two layers interact through their C-termini to form an NC-CN interface (where N and C are the N and C termini, respectively) exhibits high structural stability over the simulation time due to strong hydrophobic interactions and geometrical constraints induced by the closed circular shape. The observed dimensions and molecular weight of the oligomers from atomic force microscopy (AFM) experiments are found to correspond well to our stable double-layered model with the NC-CN interface. Comparison with K3 annular structures derived from the beta 2-microglobulin suggests that the driving force for amyloid formation is sequence specific, strongly dependent on side-chain packing arrangements, structural morphologies, sequence composition, and residue positions. Combined with our previous simulations of linear-like Abeta, K3 peptide, and sup35-derived GNNQQNY peptide, the annular structures provide useful insight into oligomeric structures and driving forces that are critical in amyloid fibril formation.

  9. Depth-targeted transvascular drug delivery by using annular-shaped photomechanical waves

    Akiyama, Takuya; Sato, Shunichi; Ashida, Hiroshi; Terakawa, Mitsuhiro

    2011-02-01

    Laser-based drug delivery is attractive for the targeting capability due to high spatial controllability of laser energy. Recently, we found that photomechanical waves (PMWs) can transiently increase the permeability of blood vessels in skin, muscle and brain of rats. In this study, we examined the use of annular-shaped PMWs to increase pressure at target depths due to superposition effect of pressure waves. This can increase the permeability of blood vessels located in the specific depth regions, enabling depth-targeted transvascular drug delivery. Annular PMWs were produced by irradiating a laser-absorbing material with annular-shaped pulsed laser beams that were produced by using an axicon lens. We first examined propagation and pressure characteristics of annular PMWs in tissue phantoms and confirmed an increased pressure at a target depth, which can be controlled by changing laser parameters. We injected Evans blue (EB) into a rat tail vein, and annular PMWs (inner diameter, 3 mm; outer diameter, 5 mm) were applied from the myofascial surface of the anterior tibialis muscle. After perfusion fixation, we observed fluorescence originating from EB in the tissue. We observed intense fluorescence at a target depth region of around 5 mm. These results demonstrate the capability of annular PMWs for depth-targeted transvascular drug delivery.

  10. Triple antibiotic combination therapy may improve but not resolve granuloma annulare.

    Simpson, Brenda; Foster, Shannon; Ku, Jennifer H; Simpson, Eric L; Ehst, Benjamin D

    2014-01-01

    Granuloma annulare is a fairly common entity yet lacks reliable treatment options especially when multiple lesions or dissemination exists. A recent case series suggests that a regimen of three oral antibiotics may prove to be an effective treatment. Our objective is to evaluate the efficacy of once monthly triple antibiotic therapy for granuloma annulare. We conducted an open-label prospective study of subjects with at least five lesions of granuloma annulare who received once monthly rifampin, ofloxacin, and minocycline for 6 months. Improvement was measured with a novel objective Granuloma Annulare Severity Index (GASI) scoring system. Twenty-one subjects enrolled. Ten subjects (48%) achieved at least a 50% reduction in their GASI, including three subjects (14%) who reached 75% improvement and one subject (5%) whose skin cleared. Six subjects (29%) had no change or worsening of their granuloma annulare. Median GASI scores decreased significantly by 15 points (p antibiotic use may improve but not clear granuloma annulare over 6 months. Randomized trials may be warranted to further assess this therapy.

  11. Fluid-Structure Interaction Analysis on Turbulent Annular Seals of Centrifugal Pumps during Transient Process

    Qinglei Jiang

    2011-01-01

    Full Text Available The current paper studies the influence of annular seal flow on the transient response of centrifugal pump rotors during the start-up period. A single rotor system and three states of annular seal flow were modeled. These models were solved using numerical integration and finite difference methods. A fluid-structure interaction method was developed. In each time step one of the three annular seal models was chosen to simulate the annular seal flow according to the state of rotor systems. The objective was to obtain a transient response of rotor systems under the influence of fluid-induced forces generated by annular seal flow. This method overcomes some shortcomings of the traditional FSI method by improving the data transfer process between two domains. Calculated results were in good agreement with the experimental results. The annular seal was shown to have a supportive effect on rotor systems. Furthermore, decreasing the seal clearance would enhance this supportive effect. In the transient process, vibration amplitude and critical speed largely changed when the acceleration of the rotor system increased.

  12. Cultivation of Spirulina maxima in an annular photochemical reactor

    Leduy, A.; Therien, N.

    1979-08-01

    An 8-L annular photochemical reactor has been designed and built for the cultivation of micro- or semi-microalgae at the laboratory scale. It may be operated in batch or continuous mode and is controlled for pH, temperature, gas mixture ratio (CO/sub 2/ and air), flow rate, light intensity and also illumination type (daylight or plant growth light) and mode (continuous or intermittent). It behaves as a perfect mixed reactor for all concentrations of algal cells. The reactor was used for the cultivation of the blue-green alga Spirulina maxima in a synthetic medium in both batch and continuous operations. At the dilution rate of 0.24 day/sup -1/, the optimal productivity was 0.91 g/L-day for biomass or 0.55 g/L-day for protein. This is equivalent to 14.5 g/m/sup 2/-day for biomass or 8.7 g/m/sup 2/-day for protein. The optimal productivity as well as the chemical composition of the algal biomass were comparable to results obtained from pilot plant studies and reported in the current literature.

  13. Annular beam shaping system for advanced 3D laser brazing

    Pütsch, Oliver; Stollenwerk, Jochen; Kogel-Hollacher, Markus; Traub, Martin

    2012-10-01

    As laser brazing benefits from advantages such as smooth joints and small heat-affected zones, it has become established as a joining technology that is widely used in the automotive industry. With the processing of complex-shaped geometries, recent developed brazing heads suffer, however, from the need for continuous reorientation of the optical system and/or limited accessibility due to lateral wire feeding. This motivates the development of a laser brazing head with coaxial wire feeding and enhanced functionality. An optical system is designed that allows to generate an annular intensity distribution in the working zone. The utilization of complex optical components avoids obscuration of the optical path by the wire feeding. The new design overcomes the disadvantages of the state-of-the-art brazing heads with lateral wire feeding and benefits from the independence of direction while processing complex geometries. To increase the robustness of the brazing process, the beam path also includes a seam tracking system, leading to a more challenging design of the whole optical train. This paper mainly discusses the concept and the optical design of the coaxial brazing head, and also presents the results obtained with a prototype and selected application results.

  14. Stability of three-layered core-annular flow

    Pillai, Dipin; Pushpavanam, Subramaniam; Sundararajan, T.

    2016-11-01

    Stability of a three-layered core-annular flow is analyzed using the method of modal linear stability analysis. A temporal analysis shows that the flow becomes unstable to two modes of instability when inertial effects are negligible. An energy budget analysis reveals that these two modes correspond to capillary instability associated with each fluid-fluid interface. With an increase in Reynolds number, the system exhibits additional Reynolds stress modes of instabilities. These modes correspond to the Tollmien-Schlichting type of waves associated with high Reynolds number shear flows, and are considered precursor to transition to turbulence. An investigation of the parameter space reveals that the system may simultaneously show up to 5 distinct modes of instability, viz., the two capillary modes at each interface and three Reynolds stress modes in the bulk of each phase. In addition, a spatio-temporal analysis shows that the Reynolds stress modes are always convectively unstable whereas the capillary modes may undergo a transition from convective to absolute instability with decrease in Weber number. To obtain encapsulated droplets in experiments, the operating parameters must be chosen such that the system lies in the regime of convective instability. MHRD-Govt of India, NSF 0968313.

  15. Linear Unsteady Aerodynamic Forces on Vibrating Annular Cascade Blades

    Taketo Nagasaki; Nobuhiko Yamasaki

    2003-01-01

    The paper presents the formulation to compute numerically the unsteady aerodynamic forces on the vibrating annular cascade blades. The formulation is based on the finite volume method. By applying the TVD scheme to the linear unsteady calculations, the precise calculation of the peak of unsteady aerodynamic forces at the shock wave location like the delta function singularity becomes possible without empirical constants. As a further feature of the present paper, results of the present numerical calculation are compared with those of the double lineaxization theory (DLT), which assumes small unsteady and steady disturbances but the unsteady disturbances are much smaller than the steady disturbances. Since DLT requires fax less computational resources than the present numerical calculation, the validation of DLT is quite important from the engineering point of view. Under the conditions of small steady disturbances, a good agreement between these two results is observed, so that the two codes axe cross-validated.The comparison also reveals the limitation on the applicability of DLT.

  16. Imbalanced superfluid state in an annular disk.

    Ye, Fei; Chen, Yan; Wang, Z D; Zhang, F C

    2009-09-02

    The imbalanced superfluid state of spin- 1/2 fermions with s-wave pairing is numerically studied by solving the Bogoliubov-de Gennes equation at zero temperature in an annular disk geometry with narrow radial width. Two distinct types of systems are considered. The first case may be relevant to heavy fermion superconductors, where magnetic field causes spin imbalance via Zeeman interaction and the system is studied in a grand canonical ensemble. As the magnetic field increases, the system is transformed from the uniform superfluid state to the Fulde-Ferrell-Larkin-Ovchinnikov state, and finally to the spin polarized normal state. The second case may be relevant to cold fermionic systems, where the number of fermions of each species is fixed as in a canonical ensemble. In this case, the ground state depends on the pairing strength. For weak pairing, the order parameter exhibits a periodic domain wall lattice pattern with a localized spin distribution at low spin imbalance, and a sinusoidally modulated pattern with extended spin distribution at high spin imbalance. For strong pairing, the phase separation between the superfluid state and polarized normal state is found to be preferable, while the increase of spin imbalance simply changes the ratio between them.

  17. Adipophilin expression in necrobiosis lipoidica, granuloma annulare, and sarcoidosis.

    Schulman, Joshua M; LeBoit, Philip E

    2015-03-01

    Necrobiosis lipoidica (NL), granuloma annulare (GA), and sarcoidosis usually are distinguished by clinical presentation and routine microscopy, but their distinction can sometimes be challenging. Historically, a clue to diagnosing NL or GA has been the identification of lipid droplets in the areas of altered collagen, but such studies have required fresh frozen tissue, making them impractical. Here, we present the first report of immunohistochemical staining to detect adipophilin, a membrane protein in lipid droplets, in NL (n = 12), GA (n = 19), sarcoidosis (n = 12), and, as a control for nonspecific tissue damage, nongranulomatous cutaneous necrosis (n = 13). Four patterns of labeling were identified: (1) extracellular, within zones of altered collagen; (2) both intracellular and extracellular, after the distribution of palisaded or scattered histiocytes; (3) intracellular, within clustered histiocytes; and (4) periadnexal. All cases of NL demonstrated pattern 1; nearly all cases of GA (18/19) demonstrated pattern 2; most sarcoidosis (10/12) demonstrated pattern 3; and nongranulomatous necrosis demonstrated either pattern 4 (6/13) or did not stain (6/13), confirming that the antibody to adipophilin did not adhere nonspecifically to the damaged tissue. An additional set of 3 biopsies with overlapping or partially sampled features of NL, GA, and/or sarcoidosis subsequently confirmed the potential utility of adipophilin staining in diagnostically challenging cases. We conclude that the pattern of adipophilin expression is a useful adjunct in the evaluation of granulomatous dermatitis.

  18. HAMLET forms annular oligomers when deposited with phospholipid monolayers.

    Baumann, Anne; Gjerde, Anja Underhaug; Ying, Ming; Svanborg, Catharina; Holmsen, Holm; Glomm, Wilhelm R; Martinez, Aurora; Halskau, Oyvind

    2012-04-20

    Recently, the anticancer activity of human α-lactalbumin made lethal to tumor cells (HAMLET) has been linked to its increased membrane affinity in vitro, at neutral pH, and ability to cause leakage relative to the inactive native bovine α-lactalbumin (BLA) protein. In this study, atomic force microscopy resolved membrane distortions and annular oligomers (AOs) produced by HAMLET when deposited at neutral pH on mica together with a negatively charged lipid monolayer. BLA, BAMLET (HAMLET's bovine counterpart) and membrane-binding Peptide C, corresponding to BLA residues 75-100, also form AO-like structures under these conditions but at higher subphase concentrations than HAMLET. The N-terminal Peptide A, which binds to membranes at acidic but not at neutral pH, did not form AOs. This suggests a correlation between the capacity of the proteins/peptides to integrate into the membrane at neutral pH-as observed by liposome content leakage and circular dichroism experiments-and the formation of AOs, albeit at higher concentrations. Formation of AOs, which might be important to HAMLET's tumor toxic action, appears related to the increased tendency of the protein to populate intermediately folded states compared to the native protein, the formation of which is promoted by, but not uniquely dependent on, the oleic acid molecules associated with HAMLET.

  19. Friction factor of annular Poiseuille flow in a transitional regime

    Takahiro Ishida

    2016-12-01

    Full Text Available Annular Poiseuille flows in a transitional regime were investigated by direct numerical simulations with an emphasis on turbulent statistics including the friction factor that are affected by the presence of large-scale transitional structures. Five different radius ratios in the range of 0.1–0.8 and several friction Reynolds numbers in the range of 48–150 were analyzed to consider various flow states accompanied by characteristic transitional structures. Three characteristic structures, namely, turbulent–laminar coexistence referred to as “(straight puff,”“helical puff,” and “helical turbulence” were observed. The selection of the structures depends on both the radius ratio and the Reynolds number. The findings indicated that despite the transitional state with a turbulent–laminar coexistence, the helical turbulence resulted in a friction factor that was as high as the fully turbulent value. In contrast, with respect to the occurrence of streamwise-finite transitional structures, such as straight/helical puffs, the friction factor decreased in a stepwise manner toward a laminar level. The turbulent statistics revealed asymmetric distributions with respect to the wall-normal direction wherein the profiles and magnitudes were significantly influenced by the occurrence of transitional structures.

  20. Numerical Study of Transition of an Annular Lift Fan Aircraft

    Yun Jiang

    2016-09-01

    Full Text Available The present study aimed at studying the transition of annular lift fan aircraft through computational fluid dynamics (CFD simulations. The oscillations of lift and drag, the optimization for the figure of merit, and the characteristics of drag, yawing, rolling and pitching moments in transition are studied. The results show that a two-stage upper and lower fan lift system can generate oscillations of lift and drag in transition, while a single-stage inner and outer fan lift system can eliminate the oscillations. The characteristics of momentum drag of the single-stage fans in transition are similar to that of the two-stage fans, but with the peak of drag lowered from 0.63 to 0.4 of the aircraft weight. The strategy to start transition from a negative angle of attack −21° further reduces the peak of drag to 0.29 of the weight. The strategy also reduces the peak of pitching torque, which needs upward extra thrusts of 0.39 of the weight to eliminate. The peak of rolling moment in transition needs differential upward thrusts of 0.04 of the weight to eliminate. The requirements for extra thrusts in transition lead to a total thrust–weight ratio of 0.7, which makes the aircraft more efficient for high speed cruise flight (higher than 0.7 Ma.

  1. Modeling and analysis of thermoacoustic instabilities in an annular combustor

    Murthy, Sandeep; Sayadi, Taraneh; Le Chenadec, Vincent; Schmid, Peter

    2015-11-01

    A simplified model is introduced to study thermo-acoustic instabilities in axisymmetric combustion chambers. Such instabilities can be triggered when correlations between heat-release and pressure oscillations exist, leading to undesirable effects. Gas turbine designs typically consist of a periodic assembly of N identical units; as evidenced by documented studies, the coupling across sectors may give rise to unstable modes, which are the highlight of this study. In the proposed model, the governing equations are linearized in the acoustic limit, with each burner modeled as a one-dimensional system, featuring acoustic damping and a compact heat source. The coupling between the burners is accounted for by solving the two-dimensional wave equation over an annular region, perpendicular to the burners, representing the chamber's geometry. The discretization of these equations results in a set of coupled delay-differential equations, that depends on a finite set of parameters. The system's periodicity is leveraged using a recently developed root-of-unity formalism (Schmid et al., 2015). This results in a linear system, which is then subjected to modal and non-modal analysis to explore the influence of the coupled behavior of the burners on the system's stability and receptivity.

  2. Reactor pulse repeatability studies at the annular core research reactor

    DePriest, K.R. [Applied Nuclear Technologies, Sandia National Laboratories, Mail Stop 1146, Post Office Box 5800, Albuquerque, NM 87185-1146 (United States); Trinh, T.Q. [Nuclear Facility Operations, Sandia National Laboratories, Mail Stop 0614, Post Office Box 5800, Albuquerque, NM 87185-1146 (United States); Luker, S. M. [Applied Nuclear Technologies, Sandia National Laboratories, Mail Stop 1146, Post Office Box 5800, Albuquerque, NM 87185-1146 (United States)

    2011-07-01

    The Annular Core Research Reactor (ACRR) at Sandia National Laboratories is a water-moderated pool-type reactor designed for testing many types of objects in the pulse and steady-state mode of operations. Personnel at Sandia began working to improve the repeatability of pulse operations for experimenters in the facility. The ACRR has a unique UO{sub 2}-BeO fuel that makes the task of producing repeatable pulses difficult with the current operating procedure. The ACRR produces a significant quantity of photoneutrons through the {sup 9}Be({gamma}, n){sup 8}Be reaction in the fuel elements. The photoneutrons are the result of the gammas produced during fission and in fission product decay, so their production is very much dependent on the reactor power history and changes throughout the day/week of experiments in the facility. Because the photoneutrons interfere with the delayed-critical measurements required for accurate pulse reactivity prediction, a new operating procedure was created. The photoneutron effects at delayed critical are minimized when using the modified procedure. In addition, the pulse element removal time is standardized for all pulse operations with the modified procedure, and this produces less variation in reactivity removal times. (authors)

  3. Measurement of large aspheric surfaces by annular subaperture stitching interferometry

    Xiaokun Wang; Lihui Wang; Longhai Yin; Binzhi Zhang; Di Fan; Xuejun Zhang

    2007-01-01

    A new method for testing aspheric surfaces by annular subaperture stitching interferometry is introduced.It can test large-aperture and large-relative-aperture aspheric surfaces at high resolution, low cost, and high efficiency without auxiliary null optics. The basic principle of the method is described, the synthetical optimization stitching model and effective algorithm are established based on simultaneous least-square fitting. A hyperboloid with an aperture of 350 mm is tested by this method. The obtained peak-to-valley (PV) and root-mean-square (RMS) values of the surface error after stitching are 0.433λ and 0.052λ (λis 632.8 nm), respectively. The reconstructed surface map is coincide with the entire surface map from null test, and the difference of PV and RMS errors between them are 0.031λ and 0.005λ, respectively.This stitching model provides another quantitive method for testing large aspheric surfaces besides null compensation.

  4. An Unusual Presentation of Annular Pancreas: A Case Report

    Saleheh Ala

    2015-01-01

    Full Text Available Abstract Annular pancreas (AP is a rare congenital malformation resulting from failure of pancreas ventral anlage rotation with the duodenum. This leads to a ring of pancreatic tissue that envelops the duodenum. Clinical manifestations of AP most commonly develop in infancy or early childhood but can present at any age. The diagnosis of AP, usually suggested by an upper GI series or abdominal CT scan, but surgery is considered the gold standard diagnostic method. Surgical bypass of the annulus in all patients with symptomatic AP is recommended. We report a one year old girl who presented with intermittent, non projectile, non bilious vomiting that occurred 1h to 2h after feeding since neonatal period. Upper GI contrast study demonstrates, a dilated duodenal bulb associated with narrowing of post bulbar area. The patient underwent surgical correction of the obstruction. A bypass of the ectopic pancreas tissue was performed by duodenoduodenostomy. Considering the rarity of this congenital abnormality, presenting with chronic partial duodenal obstruction, and its successful correction by surgical means have prompted us to report the case.

  5. Influences of phase shift on superresolution performances of annular filters

    Liu Xi-Min; Liu Li-Ren; Bai Li-Hua

    2006-01-01

    This paper investigates the influences of phase shift on superresolution performances of annular filters.Firstly,it investigates the influence of phase shift on axial superresolution.It proves theoretically that axial superresolution can not be obtained by two-zone phase filter with phase shift π.and it gets the phase shift with which axial superresolution can be brought by two-zone phase filter.Secondly,it studies the influence of phase shift on transverse superresolution.It finds that the three-zone phase filter with arbitrary phase shift has an almost equal optimal transverse gain to that of commonly used three-zone phase filter,but can produce a much higher axial superresolution gain.Thirdly,it investigates the influence of phase shift on three-dimensional superresolution.Three-dimensional superresolution capability and design margin of three-zone complex filter with arbitrary phase shift are obtained,which presents the theoretical basis for three-dimensional superresolution design. Finally,it investigates the influence of phase shift on focal shift.To obtain desired focal shifts,it designs a series of three-zone phase filters with different phase shifts.A spatial light modulator (SLM) is used to implement the designed filters.By regulating the voltage imposed on the SLM,an accurate focal shift control iS obtained.

  6. Characterization of Novel Calorimeters in the Annular Core Research Reactor *

    Hehr Brian D.

    2016-01-01

    Full Text Available A series of pulsed irradiation experiments have been performed in the central cavity of Sandia National Laboratories' Annular Core Research Reactor (ACRR to characterize the responses of a set of elemental calorimeter materials including Si, Zr, Sn, Ta, W, and Bi. Of particular interest was the perturbing effect of the calorimeter itself on the ambient radiation field – a potential concern in dosimetry applications. By placing the calorimeter package into a neutron-thermalizing lead/polyethylene (LP bucket and irradiating both with and without a cadmium wrapper, it was demonstrated that prompt capture gammas generated inside the calorimeters can be a significant contributor to the measured dose in the active disc region. An MCNP model of the experimental setup was shown to replicate measured dose responses to within 10%. The internal (n,γ contribution was found to constitute as much as 50% of the response inside the LP bucket and up to 20% inside the nominal (unmodified cavity environment, with Ta and W exhibiting the largest enhancement due to their sizable (n,γ cross sections. Capture reactions in non-disc components of the calorimeter were estimated to be responsible for up to a few percent of the measured response.

  7. Flow Pressure Loss through Straight Annular Corrugated Pipes

    Sargent, Joseph R.; Kirk, Daniel R.; Marsell, Brandon; Roth, Jacob; Schallhorn, Paul A.; Pitchford, Brian; Weber, Chris; Bulk, Timothy

    2016-01-01

    Pressure loss through annular corrugated pipes, using fully developed gaseous nitrogen representing purge pipes in spacecraft fairings, was studied to gain insight into a friction factor coefficient for these pipes. Twelve pipes were tested: four Annuflex, four Masterflex and two Titeflex with ¼”, 3/8”, ½” and ¾” inner diameters. Experimental set-up was validated using smooth-pipe and showed good agreement to the Moody diagram. Nitrogen flow rates between 0-200 standard cubic feet per hour were used, producing approximate Reynolds numbers from 300-23,000. Corrugation depth varied from 0.248 = E/D = 0.349 and relative corrugation pitch of 0.192 = P/D = 0.483. Differential pressure per unit length was measured and calculated using 8-9 equidistant pressure taps. A detailed experimental uncertainty analysis, including correlated bias error terms, is presented. Results show larger differential pressure losses than smooth-pipes with similar inner diameters resulting in larger friction factor coefficients.

  8. Global Arrays

    Krishnamoorthy, Sriram; Daily, Jeffrey A.; Vishnu, Abhinav; Palmer, Bruce J.

    2015-11-01

    Global Arrays (GA) is a distributed-memory programming model that allows for shared-memory-style programming combined with one-sided communication, to create a set of tools that combine high performance with ease-of-use. GA exposes a relatively straightforward programming abstraction, while supporting fully-distributed data structures, locality of reference, and high-performance communication. GA was originally formulated in the early 1990’s to provide a communication layer for the Northwest Chemistry (NWChem) suite of chemistry modeling codes that was being developed concurrently.

  9. Propagation characteristics of annular laser beams passing through the reflection Bragg grating with deformation

    Yin, Suqin; Zhang, Bin; Dan, Youquan

    2011-06-01

    When high-power annular laser beams produced by the unstable resonator pass through the volume Bragg grating (VBG), absorption of light in the VBG will induce a temperature increment, resulting in changes in surface distortion. Considering that the surface distortion of the grating induces index and period differences, the scalar wave equations for the annular laser beams propagating in the VBG have been solved numerically and iteratively using finite-difference and sparse matrix methods. The variation in intensity distributions, the total power reflection coefficient, and the power in the bucket (PIB) for the annular laser beams passing through the reflection VBG with deformation have been analyzed quantitatively. It can be shown that the surface distortion of the VBG and the beam orders of the annular beams affect evidently the intensity distributions, the power reflection coefficient, and the PIB of the output beam. The peak intensity decreases as the deformation of the VBG increases. The total power reflection efficiency decreases significantly with the increase in deformations of the VBG. The PIB of the output beam decreases as the obscuration ratio β and the deformation of the VBG increase. For the given obscuration ratio β, the influence of deformation of reflection VBG on the PIB of the annular beams is more sensitive with increase in distortion of the VBG and decrease in beam order.

  10. Repeated mitral valve replacement in a patient with extensive annular calcification

    Kitamura Tadashi

    2011-11-01

    Full Text Available Abstract Background Mitral valve replacement in the presence of severe annular calcification is a technical challenge. Case report A 47-year-old lady who had undergone mitral and aortic valve replacement for rheumatic disease 27 years before presented with dyspnea. At reoperation, extensive mitral annular calcification was hindering the disc motion of the Starr-Edwards mitral prosthesis. The old prosthesis was removed and a St Jude Medical mechanical valve was implanted after thorough annular debridement. Postoperatively the patient developed paravalvular leak and hemolytic anemia, subsequently undergoing reoperation three days later. The mitral valve was replaced with an Edwards MIRA valve, with a bulkier sewing cuff, after more aggressive annular debridement. Although initially there was no paravalvular leak, it recurred five days later. The patient also developed a small cerebral hemorrhage. As the paravalvular leak and hemolytic anemia gradually worsened, the patient underwent reoperation 14 days later. A Carpentier-Edwards bioprosthetic valve with equine pericardial patches, one to cover the debrided calcified annulus, another as a collar around the prosthesis, was used to eliminate paravalvular leak. At 7 years postoperatively the patient is doing well without any evidence of paravalvular leak or structural valve deterioration. Conclusion Mitral valve replacement using a bioprosthesis with equine pericardial patches was useful to overcome recurrent paravalvular leak due to severe mitral annular calcification.

  11. Hydraulic study of drilling fluid flow in circular and annular tubes

    Scheid, C.M.; Calcada, L.A.; Braga, E.R.; Paraiso, E.C.H. [Universidade Federal Rural do Rio de Janeiro (PPGEQ/UFRRJ), Seropedica, RJ (Brazil). Programa de Pos-Graduacao em Engenharia Quimica. Dept. de Engenharia Qumica], E-mail: calcada@ufrrj.br; Martins, A. L. [Petroleo Brasileiro S.A. (CENPES/PETROBRAS), Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

    2011-10-15

    This study investigates the drilling fluid flow behavior of two water-based drilling fluids in circular and annular tubes. The study has four main objectives: 1) to evaluate correlations between the Power Law and the Casson rheological models, 2) to characterize the flow behavior, 3) to evaluate five hydraulic-diameter equations, and 4) to evaluate the correlations of five turbulent flow-friction factors. The experimental fluid flow loop consisted of one positive displacement pump of 25 HP connected to a 500-liter tank agitated by a 3-HP mixer. The fluids passed through six meters long tubes, arranged in three horizontal rows with independent inlets and outlets. The circular tubes had a 1 inch diameter and were configured as two concentric annular tubes. Annular Tube I had an outer diameter of 1 1/4 inch and an inner diameter of 1/2 inch. Annular Tube II had an outer diameter of 2 inches and an inner diameter of 3/4 inch. The results show that, for the fluids in exam, correlations proposed in the literature were inaccurate as far as predicting hydraulic diameter, estimating pressure drop, and defining the flow regime. In general, the performance of those correlations depended on the fluid properties and on the system's geometry. Finally, literature parameters for some of the correlations were estimated for the two drilling fluids studied. These estimations improved the predictive capacity of calculating the friction factor for real drilling fluids applications for both circular and annular tubes. (author)

  12. Overview of magnetic bearing control and linearization approaches for annular magnetically suspended devices

    Groom, N. J.

    1984-01-01

    An overview of magnetic bearing control and linearization approaches which have been considered for annular magnetically suspended devices is presented. These devices include the Annular Momentum Control Device and the Annular Suspension and Pointing System. Two approaches were investigated for controlling the magnetic actuator. One approach involves controlling the upper and lower electromagnets differentially about a bias flux. The bias flux can either be supplied by permanent magnets in the magnetic circuit or by bias currents. In the other approach, either the upper electromagnet or the lower electromagnet is controlled depending on the direction of force required. One advantage of the bias flux is that for small gap perturbations about a fixed operating point, the force-current characteristic is linear. Linearization approaches investigated for individual element control include an analog solution of the nonlinear electromagnet force equation and a microprocessor-based table lookup method.

  13. Elastic Properties of the Annular Ligament of the Human Stapes--AFM Measurement.

    Kwacz, Monika; Rymuza, Zygmunt; Michałowski, Marcin; Wysocki, Jarosław

    2015-08-01

    Elastic properties of the human stapes annular ligament were determined in the physiological range of the ligament deflection using atomic force microscopy and temporal bone specimens. The annular ligament stiffness was determined based on the experimental load-deflection curves. The elastic modulus (Young's modulus) for a simplified geometry was calculated using the Kirchhoff-Love theory for thin plates. The results obtained in this study showed that the annular ligament is a linear elastic material up to deflections of about 100 nm, with a stiffness of about 120 N/m and a calculated elastic modulus of about 1.1 MPa. These parameters can be used in numerical and physical models of the middle and/or inner ear.

  14. Optimization of gap sizes for the high performance of annular nuclear fuels

    Kwon, Young Doo; Kwon, Soon Bum; Cho, Hui Jeong; Kim, Seong Su [Kyungpook National University, Daegu (Korea, Republic of)

    2015-04-15

    Solid-type nuclear fuels have been used for nuclear reactors for a long time. Many countries are currently developing annular fuels to improve the efficiency of nuclear fuels. The thermoelastic-plastic-creep analyses of solid- and annular-type rods were conducted under the same conditions. The temperature and stress of the solid- and annular-type rods were compared on the basis of gap size. In this study, we examined the advantages and disadvantages of annular-type fuel regarding the temperature and stress of the pellet and cladding. The inner and outer gaps between the pellet and cladding play important roles in the temperature and stress distributions of fuel systems. Therefore, the optimization of gaps in fuel systems was conducted for a low temperature under certain stress conditions. hermoelasticplastic-creep analyses were conducted by using an in-house thermoelastic-plastic-creep finite element analysis program in Visual FORTRAN with the effective stress function algorithm. Nonlinear iterative stress analyses were conducted by nonlinear iterative temperature analyses; that is, a quasi-fully coupled algorithm was applied to this procedure. In this study, the thermoelastic-plastic-creep analysis of pressurized water reactor annular fuels was conducted to determine the contacting tendency of the inner-outer gaps between the annular fuel pellets and cladding, as well as to optimize the gap sizes by using the commercial package PIAnO for efficient heat transfer at certain stress levels. Most analyses were conducted until the gaps disappeared. However, certain analyses lasted for 1582 days, after which the fuels were replaced.

  15. Dynamics of annular bright field imaging in scanning transmission electron microscopy

    Findlay, S.D., E-mail: scott@sigma.t.u-tokyo.ac.jp [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); Shibata, N. [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); PRESTO, Japan Science and Technology Agency, Saitama 332-0012 (Japan); Sawada, H.; Okunishi, E.; Kondo, Y. [JEOL Ltd., Tokyo 196-8558 (Japan); Ikuhara, Y. [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); Nanostructures Research Laboratory, Japan Fine Ceramics Center, Nagoya 456-8587 (Japan); WPI Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan)

    2010-06-15

    We explore the dynamics of image formation in the so-called annular bright field mode in scanning transmission electron microscopy, whereby an annular detector is used with detector collection range lying within the cone of illumination, i.e. the bright field region. We show that this imaging mode allows us to reliably image both light and heavy columns over a range of thickness and defocus values, and we explain the contrast mechanisms involved. The role of probe and detector aperture sizes is considered, as is the sensitivity of the method to intercolumn spacing and local disorder.

  16. Histological study of the annular ligament in the rabbitfish eye (Siganus sp.).

    Asli, Marziye; Mansoori, Forooghsadat; Sattari, Amir

    2012-01-01

    Rabbitfish is economically valuable teleost species which lives in shallow coastal waters. Two species of rabbit fish have been recognized in southern sea of Iran (Persian gulf) as namely Siganus sutor and Siganus javus. In the current study, in order to investigate the histology of the annular ligament of the S. javus' eye, the prepared sections of the eyes of twelve healthy specimens were studied under light microscope. The results revealed that annular ligament is a crescent shape structure which is situated between the scleral stroma anteriorly and the iris posteriorly. It contains a vascularized, amorphous and granular matrix with fibers of dense connective tissue; high glycogen content and melanin pigments.

  17. Frequency Equations for the In-Plane Vibration of Circular Annular Disks

    S. Bashmal; Bhat, R; S. Rakheja

    2010-01-01

    This paper deals with the in-plane vibration of circular annular disks under combinations of different boundary conditions at the inner and outer edges. The in-plane free vibration of an elastic and isotropic disk is studied on the basis of the two-dimensional linear plane stress theory of elasticity. The exact solution of the in-plane equation of equilibrium of annular disk is attainable, in terms of Bessel functions, for uniform boundary conditions. The frequency equations for different mod...

  18. Elliptic annular Josephson tunnel junctions in an external magnetic field: the statics

    Monaco, Roberto; Granata, Carmine; Vettoliere, Antonio

    2015-01-01

    symmetric electrodes a transverse magnetic field is equivalent to an in-plane field applied in the direction of the current flow. Varying the ellipse eccentricity we reproduce all known results for linear and ring-shaped JTJs. Experimental data on high-quality Nb/Al-AlOx/Nb elliptic annular junctions...... or in the perpendicular direction. We report a detailed study of both short and long elliptic annular junctions having different eccentricities. For junctions having a normalized perimeter less than one the threshold curves are derived and computed even in the case with one trapped Josephson vortex. For longer junctions...

  19. Generation of annular, high-charge electron beams at the Argonne wakefield accelerator

    Wisniewski, E. E.; Li, C.; Gai, W.; Power, J.

    2013-01-01

    We present and discuss the results from the experimental generation of high-charge annular(ring-shaped)electron beams at the Argonne Wakefield Accelerator (AWA). These beams were produced by using laser masks to project annular laser profiles of various inner and outer diameters onto the photocathode of an RF gun. The ring beam is accelerated to 15 MeV, then it is imaged by means of solenoid lenses. Transverse profiles are compared for different solenoid settings. Discussion includes a comparison with Parmela simulations, some applications of high-charge ring beams,and an outline of a planned extension of this study.

  20. Cross-field transport of electrons at the magnetic throat in an annular plasma reactor

    Zhang, Yunchao; Charles, Christine; Boswell, Rod

    2017-01-01

    Cross-field transport of electrons has been studied at the magnetic throat of the annular Chi-Kung reactor. This annular configuration allows the creation of a low pressure argon plasma with two distinct electron heating locations by independently operating a radio-frequency antenna surrounding the outer source tube, or an antenna housed inside the inner source tube. The two antenna cases show opposite variation trends in radial profiles of electron energy probability function, electron density, plasma potential and electron temperature. The momentum and energy transport coefficients are obtained from the electron energy probability functions, and the related electron fluxes follow the path of electron cooling across the magnetic throat.

  1. Displacement of one Newtonian fluid by another: density effects in axial annular flow

    Szabo, Peter; Hassager, Ole

    1997-01-01

    The arbitrary Lagrange-Euler (ALE) finite elementtechnique is used to simulate 3D displacement oftwo immiscible Newtonian fluids in vertical annular wells. For equally viscous fluids the effect of distinct fluid densities is investigated in the region of low to intermediate Reynolds numbers....... Comparison with a simple theory for drainage of thin films is performed. It is found that recirculations deform the fluid-fluidinterface significantly in situations dominated by buoyancy forces. Also, a deviation from the concentric annular geometry is shown to induce azimuthal transport of fluid. Finally......, the efficiency of the displacement is analysed for various flow situations....

  2. Experimental Study on Convective Boiling Heat Transfer in Vertical Narrow Gap Annular Tube

    Li Bin; He Anding; Wang Yueshe; Zhou Fangde

    2001-01-01

    Experiments are conducted to investigate the characteristics of single-phase forced-flow convection and boiling heat transfer of R113 flowing through annular tube with gap of 1, 1.5 and 2.5 mm, and also the visualization test are carried out to get two-phase flow regime. The data show that the Nusselt numbers for the narrow-gap are higher than those predicted by traditional large channel correlation and boiling heat transfer is enhanced. Based on the data obtained in this investigation, correlations for single-phase, forced convection and flow boiling in annular tube of different gap size has been developed.

  3. Histological study of the annular ligament in the rabbitfish eye (Siganus sp.

    Marziye Asli

    2012-12-01

    Full Text Available Rabbitfish is economically valuable teleost species which lives in shallow coastalwaters. Two species of rabbit fish have been recognized in southern sea of Iran (Persiangulf as namely Siganus sutor and Siganus javus. In the current study, in order toinvestigate the histology of the annular ligament of the S. javus’ eye, the prepared sectionsof the eyes of twelve healthy specimens were studied under light microscope. The resultsrevealed that annular ligament is a crescent shape structure which is situated between thescleral stroma anteriorly and the iris posteriorly. It contains a vascularized, amorphousand granular matrix with fibers of dense connective tissue; high glycogen content andmelanin pigments.

  4. Quasi-static transient thermal stresses in a thick annular disc

    V S Kulkarni; K C Deshmukh

    2007-10-01

    The present paper deals with the determination of transient thermal stresses in a thick annular disc. A thick annular disc is considered having zero initial temperature and subjected to arbitrary heat flux on the upper and lower surfaces where as the fixed circular edges are at zero temperature.The governing heat conduction equation have been solved by using integral transform technique. The results are obtained in series form in terms of Bessel’s functions. The results for displacement and stresses have been computed numerically and are illustrated graphically

  5. Radially polarized annular beam generated through a second-harmonic-generation process.

    Sato, Shunichi; Kozawa, Yuichi

    2009-10-15

    A radially polarized beam with an annular intensity pattern was generated through a second-harmonic-generation process by focusing an azimuthally polarized Ti:sapphire pulsed laser beam to a c-cut beta-barium borate (BBO) crystal. The annular intensity pattern of the second-harmonic wave had a nearly sixfold symmetry as a result of the nonlinear susceptibility tensor of the BBO crystal. The width of the annulus was as narrow as less than 1/40th of its radius.

  6. Near-limit propagation of gaseous detonations in narrow annular channels

    Gao, Y.; Ng, H. D.; Lee, J. H. S.

    2017-03-01

    New results on the near-limit behaviors of gaseous detonations in narrow annular channels are reported in this paper. Annular channels of widths 3.2 and 5.9 mm were made using circular inserts in a 50.8 mm-diameter external tube. The length of each annular channel was 1.8 m. Detonations were initiated in a steel driver tube where a small volume of a sensitive C2H2+ 2.5O2 mixture was injected to facilitate detonation initiation. A 2 m length of circular tube with a 50.8 mm diameter preceded the annular channel so that a steady Chapman-Jouguet (CJ) detonation was established prior to entering the annular channel. Four detonable mixtures of C2H2 {+} 2.5O2 {+} 85 % Ar, C2H2 {+} 2.5O2 {+} 70 % Ar, C3H8 {+} 5O2, and CH4 {+} 2O2 were used in the present study. Photodiodes spaced 10 cm throughout the length of both the annular channel and circular tube were used to measure the detonation velocity. In addition, smoked foils were inserted into the annular channel to monitor the cellular structure of the detonation wave. The results show that, well within the detonability limits, the detonation wave propagates along the channel with a small local velocity fluctuation and an average global velocity can be deduced. The average detonation velocity has a small deficit of 5-15 % far from the limits and the velocity rapidly decreases to 0.7V_{CJ}-0.8V_{CJ} when the detonation propagates near the limit. Subsequently, the fluctuation of local velocity also increases as the decreasing initial pressure approaches the limit. In the two annular channels used in this work, no galloping detonations were observed for both the stable and unstable mixtures tested. The present study also confirms that single-headed spinning detonation occurs at the limit, as in a circular tube, rather than the up and down "zig zag" mode in a two-dimensional, rectangular channel.

  7. DETERMINATION OF TEMPERATURE DISTRIBUTION FOR ANNULAR FINS WITH TEMPERATURE DEPENDENT THERMAL CONDUCTIVITY BY HPM

    Davood Domairry Ganji

    2011-01-01

    Full Text Available In this paper, homotopy perturbation method has been used to evaluate the temperature distribution of annular fin with temperature-dependent thermal conductivity and to determine the temperature distribution within the fin. This method is useful and practical for solving the nonlinear heat transfer equation, which is associated with variable thermal conductivity condition. The homotopy perturbation method provides an approximate analytical solution in the form of an infinite power series. The annular fin heat transfer rate with temperature-dependent thermal conductivity has been obtained as a function of thermo-geometric fin parameter and the thermal conductivity parameter describing the variation of the thermal conductivity.

  8. Liquid–Liquid Mixing Studies in Annular Centrifugal Contactors Comparing Stationary Mixing Vane Options

    Wardle, Kent E.

    2015-11-10

    Comparative studies of multiphase operation of annular centrifugal contactors showing the impact of housing stationary mixing vane configuration. A number of experimental results for several different mixing vane options are reported with selected measurements in a lab-scale 5 cm contactor and 12.5 cm engineering-scale unit. Fewer straight vanes give greater mixingzone hold-up compared to curved vanes. Quantitative comparison of droplet size distribution also showed a significant decrease in mean diameter for four straight vanes versus eight curved vanes. This set of measurements gives a compelling case for careful consideration of mixing vane geometry when evaluating hydraulic operation and extraction process efficiency of annular centrifugal contactors.

  9. Annular Lichenoid Dermatitis of Youth: A Report of 2 Cases and a Review of the Literature.

    Vázquez-Osorio, I; González-Sabín, M; Gonzalvo-Rodríguez, P; Rodríguez-Díaz, E

    2016-01-01

    Annular lichenoid dermatitis of youth is a lichenoid dermatosis of unknown etiology. It mostly affects children and adolescents and has well-defined clinical and histological characteristics that permit a diagnosis. We present 2 new cases of annular lichenoid dermatitis of youth with classical clinical features in 2 girls, aged 2 and 4 years. The histologic findings, however, differed from those reported in the literature in that the lichenoid inflammatory infiltrate was located primarily at the top of the dermal papillae and not at the tips of the rete ridges. In both cases, the lesions regressed spontaneously without treatment.

  10. High quantum efficiency annular backside silicon photodiodes for reflectance pulse oximetry in wearable wireless body sensors

    Duun, Sune Bro; Haahr, Rasmus Grønbek; Hansen, Ole;

    2010-01-01

    The development of annular photodiodes for use in a reflectance pulse oximetry sensor is presented. Wearable and wireless body sensor systems for long-term monitoring require sensors that minimize power consumption. We have fabricated large area 2D ring-shaped silicon photodiodes optimized....../2) cm(-1) are achieved. The photodiodes are incorporated into a wireless pulse oximetry sensor system embedded in an adhesive patch presented elsewhere as 'The Electronic Patch'. The annular photodiodes are fabricated using two masked diffusions of first boron and subsequently phosphor. The surface...

  11. On the levitation force in horizontal core-annular flow with a large viscosity ratio and small density ratio

    Ooms, G.; Pourquie, M.J.B.M.; Beerens, J.C.

    2013-01-01

    A numerical study has been made of horizontal core-annular flow: the flow of a high-viscosity liquid core surrounded by a low-viscosity liquid annular layer through a horizontal pipe. Special attention is paid to the question how the buoyancy force on the core, caused by a density difference between

  12. LINEARIZATION OF ANNULAR IMAGE OF PANORAMIC ANNULAR LENS%全景环形透镜环形象的线性化研究

    朱方明; 杨国光; 姚炜勇; 程惠全

    2001-01-01

    全景环形透镜(PAL)独特的成象性能,即环绕光轴360°产生一个环形象且景深为无穷远,使得由PAL组成的观测系统没有活动部件能同时观察透镜周围的景物.但PAL所成的环形象不便于人眼观察和测量,有畸变、失真,为此,本文根据图象坐标变换,实现了一种环形象的线性恢复,即首先将环形象线性化处理,再对其进行插值,实验结果表明线性化效果较好.该图象处理技术可以为发挥PAL的许多潜在应用创造条件.%For the special imaging feature of Panoramic Annular Lens,that forming an annular image circling the axis and having endless depth of field,the observing system made up of PAL can be used to observe object around the lens without moving part.But the annular image formed by PAL is not only unconvenient for observation and measurement,but also has distortion phenominon.According to coordinate convertion of image,a method of linearizing annular image is presented.The results show that the effect of linearization is good.With this method,it can be found basis for potential application of PAL.

  13. Reference values of tricuspid annular peak systolic velocity in healthy pediatric patients, calculation of z score, and comparison to tricuspid annular plane systolic excursion.

    Koestenberger, Martin; Nagel, Bert; Ravekes, William; Avian, Alexander; Heinzl, Bernd; Cvirn, Gerhard; Fritsch, Peter; Fandl, Andrea; Rehak, Thomas; Gamillscheg, Andreas

    2012-01-01

    The tricuspid annular peak systolic velocity (TAPSV) is an echocardiographic measurement assessing right ventricular systolic function in children and adults. We determined the growth-related changes of the TAPSV to establish the references values for the entire pediatric age group. A prospective study was conducted of a group of 860 healthy pediatric patients (age 1 day to 18 years; body surface area [BSA] 0.14 to 2.30 m(2)). We determined the effects of age, gender, and BSA on the TAPSV values. Stepwise linear multiple regression analysis was used to estimate the TAPSV from the age, BSA, and gender. A correlation of normal TAPSV with normal tricuspid annular plane systolic excursion values was performed. The TAPSV ranged from a mean of 7.2 cm/s (z score ± 2: 4.8 to 9.5 cm/s) in the newborn to 14.3 cm/s (z score ± 2: 10.6 to 18.6 cm/s) in the 18-year-old adolescent. The TAPSV values showed a positive correlation with age and BSA, with a nonlinear course. No significant difference was found in the TAPSV values according to gender. A significant correlation was found between the TAPSV and tricuspid annular plane systolic excursion values in our pediatric population. In conclusion, the z scores of the TAPSV values were calculated, and percentile charts were established to serve as reference data for patients with congenital heart disease.

  14. SYSTEMATIC STUDIES IN TURNERA (TURNERACEAE II. SERIES ANNULARES, CAPITATAE, PAPILLIFERAE AND MICROPHYLLAE ESTUDIOS SISTEMÁTICOS EN TURNERA (TURNERACEAE II. SERIES ANNULARES, CAPITATAE, MICROPHYLEAE Y PAPILLIFERAE

    María Mercedes Arbo

    2010-11-01

    Full Text Available

    Turnera L. includes around 100 American species and two African ones, arranged in nine series. In this paper, the following four series embracing 21 species are revised: Annulares, Capitatae, Microphyllae and Papilliferae. Six new taxa are described: Thatschbachii, Thatschbachii var. miniata, Tmaracasana,and T.princeps of the seriesCapitatae, Tasymmetrica of the series Microphyllae, and Tcaatingana of the series Papilliferae. The species of these four series share the common features of simple and glandular hairs, generally well-developed floral peduncle, absent pedicel, linear or elliptic prophylls, generally warty or granulate fruit, and a floral tube, appendicular in nature, in that it is the product of the fusion of the lower part of the calyx and corolla, with the staminal filaments adnate only at the base. In the series Annulares,
    Microphyllae and Papilliferae the leaves and young stems are fragrant, the scent being produced by the glandular hairs, and the floral peduncle is shortly adnate to the petiole. Three
    series, Annulares, Capitatae and Microphyllae, have leaves with generally well developed stipules and a disjunct geographical distribution. The series Annulares and Capitatae have nectaries and villous or hirsute styles, while Microphyllae and Papilliferae lack nectaries and their styles are glabrous or somewhat pilose. In some species of Microphyllae the staminal filaments are joined at the base, forming an annular structure 0,05-0,50 mm high. The seeds are peculiar in Annulares, being very short, with a central, prominent and slightly concave chalaza. In the series Capitatae, the flowers are gathered in short, capitate inflorescences, the length of the peduncles being variable or sometimes wanting, and the seeds are obovoid, reticulate or striate. The leaves of Microphyllae are small, with the stipules adnate to the foliar
    base; setiform glandular hairs, similar to those of

  15. Testing the kibble-zurek scenario with annular josephson tunnel junctions

    Kavoussanaki; Monaco; Rivers

    2000-10-16

    In parallel with Kibble's description of the onset of phase transitions in the early Universe, Zurek has provided a simple picture for the onset of phase transitions in condensed matter systems, supported by agreement with experiments in 3He and superconductors. We show how experiments with annular Josephson tunnel junctions can, and do, provide further support for this scenario.

  16. Frequency Equations for the In-Plane Vibration of Circular Annular Disks

    S. Bashmal

    2010-01-01

    Full Text Available This paper deals with the in-plane vibration of circular annular disks under combinations of different boundary conditions at the inner and outer edges. The in-plane free vibration of an elastic and isotropic disk is studied on the basis of the two-dimensional linear plane stress theory of elasticity. The exact solution of the in-plane equation of equilibrium of annular disk is attainable, in terms of Bessel functions, for uniform boundary conditions. The frequency equations for different modes can be obtained from the general solutions by applying the appropriate boundary conditions at the inner and outer edges. The presented frequency equations provide the frequency parameters for the required number of modes for a wide range of radius ratios and Poisson's ratios of annular disks under clamped, free, or flexible boundary conditions. Simplified forms of frequency equations are presented for solid disks and axisymmetric modes of annular disks. Frequency parameters are computed and compared with those available in literature. The frequency equations can be used as a reference to assess the accuracy of approximate methods.

  17. A comparison between numerical predictions and theoretical and experimental results for laminar core-annular flow

    Beerens, J.C.; Ooms, G.; Pourquie, M.J.B.M.; Westerweel, J.

    2014-01-01

    high-viscosity liquid core surrounded by a laminar low-viscosity liquid annular layer through a vertical pipe. The numerical results are compared with theoretical results from linear stability calculations and with experimental data. The comparison is good and the general conclusion of our study is

  18. Optimization of geometry of annular seat valves suitable for Digital Displacement fluid power pumps/motors

    Rømer, Daniel; Johansen, Per; Pedersen, Henrik C.

    2013-01-01

    work an annular seat valve suitable for use in Digital Displacement units is considered, and the ring geometry is optimized using finite element analysis including non-linear material behaviour, contact elements and fluid pressure penetrating load, closely reflecting the actual load of the seat valve...

  19. Experimental investigation of three-dimensional flow structures in annular swirling jets

    Percin, M.; Vanierschot, M.; Van Oudheusden, B.W.

    2015-01-01

    Annular jet flows are of practical interest in view of their occurrence in many industrial applications in the context of bluff-body combustors [1]. They feature different complex flow characteristics despite their simple geometry: a central recirculation zone (CRZ) as a result of flow separation be

  20. Response of an annular electrostatic probe for a right cylindrical spacer

    Johansson, Torben; MacAllister, I. W.

    2002-01-01

    The response of an annular electrostatic probe mounted in an electrode is examined with reference to a right cylindrical spacer. The study involves using the probe λ function to derive characteristic parameters. These parameters enable the response of the probe to different charge distributions...

  1. Droplets in annular-dispersed gas-liquid pipe-flows

    Van 't Westende, J.M.C.

    2008-01-01

    Annular-dispersed gas-liquid pipe-flows are commonly encountered in many industrial applications, and have already been studied for many decades. However, due to the great complexity of this type of flow, there are still many phenomena that are poorly understood. The aim of this thesis is to shed mo

  2. The benign concentric annular macular dystrophy locus maps to 6p12.3-q16.

    Lith-Verhoeven, J.J. van; Hoyng, C.B.; Helm, B. van den; Deutman, A.F.; Brink, H.M.A.; Kemperman, M.H.; Jong, W.H. de; Kremer, J.M.J.; Cremers, F.P.M.

    2004-01-01

    PURPOSE: To describe the clinical findings and to identify the genetic locus in a Dutch family with autosomal dominant benign concentric annular macular dystrophy (BCAMD). METHODS: All family members underwent ophthalmic examination. Linkage analysis of candidate retinal dystrophy loci and a whole g

  3. A Case of Erythema Annulare Centrifigum with Sjögren Syndrome

    İlgen Ertam

    2010-03-01

    Full Text Available Erythema annulare centrifigum is a dermatose which is frequently seen in adults. It is characterized by erythematous lesions which spread asymmetrically to periphery and have a collarette desquamation. Although infection, tumor, food allergy, drug reaction can play a role in the aetiology, most of the cases are idiopathic. A forty-nine years old, female patient presented to our clinic with erythematous lesions on both of her lower extremities. Six weeks prior to her referral, she treated with quinine for Sjogren syndrome. She had a diagnosis of granuloma annulare in her personal history. There was no significance in her family history. In dermatologic examination; annular erythematous plaques and collarette desquamation were detected on lower extremities. Histopathologic examination of the lesional biopsy specimen revealed focal spongiosis in the epidermis, dermal oedema, vascular proliferation and perivascular infiltration of lymphocytes, eosinophils and histiocytes. In the laboratory examination; blood count, liver and kidney function tests, sedimentation, C-reactive protein was normal. Rheumatoid factor was 30. Antinuclear antibody was 1/640 granular pattern. A case of erythema annulare centrifigum with Sjögren Syndrome is discussed with the other skin findings of the disease.

  4. The dispersive properties of a dielectricrod loaded waveguide immersed in a magnetized annular plasma

    Li Wei; Gong Ma-Li; Wei Yan-Yu; Xie Hong-Quan

    2004-01-01

    @@ Propagation properties of electromagnetic waves in a dielectric-rod waveguide immersed in a magnetized annular plasma are presented in this paper. The dispersion relations are derived and calculated. The results show that the dielectric-rod loading can make the structure less dispersive and the transmission frequency-band broadened.

  5. Granuloma Annulare, Autoimmune Thyroiditis, and Lichen Sclerosus in a Woman: Randomness or Significant Association?

    Mariele De Paola; Anastasia Batsikosta; Luca Feci; Mattia Benedetti; Roberta Bilenchi

    2013-01-01

    We report a 60-year-old Caucasian female with a 2-year history of diffused granuloma annulare (GA), who presented for the simultaneous occurrence of genital lichen sclerosus (LS) and autoimmune thyroiditis (AT). In our opinion this combination is not just coincidental but may share similar immunopathological mechanisms.

  6. Granuloma Annulare, Autoimmune Thyroiditis, and Lichen Sclerosus in a Woman: Randomness or Significant Association?

    Mariele De Paola

    2013-01-01

    Full Text Available We report a 60-year-old Caucasian female with a 2-year history of diffused granuloma annulare (GA, who presented for the simultaneous occurrence of genital lichen sclerosus (LS and autoimmune thyroiditis (AT. In our opinion this combination is not just coincidental but may share similar immunopathological mechanisms.

  7. Acute renal infarction secondary to calcific embolus from mitral annular calcification.

    Bande, Dinesh; Abbara, Suhny; Kalva, Sanjeeva P

    2011-06-01

    We report a case of a 62-year-old man who presented with right groin pain who subsequently was found to have a renal infarct secondary to calcific embolus from mitral annular calcification on CT and angiography. We briefly review the literature and discuss the importance of this entity in clinical practice.

  8. The analysis of the influence of the ferromagnetic rod in an annular magnetohydrodynamic (MHD pump

    Bergoug Nassima

    2012-01-01

    Full Text Available This paper deals with the 2D modelisation of an annular induction magnetohydrodynamic (MHD pump using finite volume method in cylindrical coordinates and taking into consideration the saturation of the ferromagnetic material. The influence of the ferromagnetic rod on the different characteristics, in the channel of the MHD pump was studied in the paper.

  9. Annular lichenoid dermatitis of youth ... and beyond: a series of 6 cases.

    Cesinaro, Anna Maria; Sighinolfi, Pamela; Greco, Antonietta; Garagnani, Lorella; Conti, Andrea; Fantini, Fabrizio

    2009-05-01

    Annular lichenoid dermatitis of youth (ALDY) is a clinico-pathologic entity described in children and young patients, clinically reminiscent of morphea, annular erythema, vitiligo or mycosis fungoides. We report on six patients presenting single or multiple lesions, distributed particularly on the flanks and abdomen, with clinical and histologic features consistent with ALDY. Two patients were young girls and four were adults males. Three patients received topical therapy and four showed complete resolution of the lesions after a 24-65 months follow-up. Analogously to the cases reported so far, immunohistochemistry showed a T cell infiltrate with a predominance of CD8+ lymphocytes, while T cell receptor rearrangement was absent in all cases. It seems appropriate to include annular lichenoid dermatitis of youth among the dermatoses with a lichenoid pattern. For the first time, we found that it can affect also adult patients, therefore we propose to rename the disease annular lichenoid dermatitis. The differential diagnosis with mycosis fungoides, especially in adult patients, is particularly crucial for their proper management and treatment.

  10. Integrated strain array for cellular mechanobiology studies

    Simmons, C. S.; Sim, J. Y.; Baechtold, P.; Gonzalez, A.; Chung, C.; Borghi, N.; Pruitt, B. L.

    2011-05-01

    We have developed an integrated strain array for cell culture enabling high-throughput mechano-transduction studies. Biocompatible cell culture chambers were integrated with an acrylic pneumatic compartment and microprocessor-based control system. Each element of the array consists of a deformable membrane supported by a cylindrical pillar within a well. For user-prescribed waveforms, the annular region of the deformable membrane is pulled into the well around the pillar under vacuum, causing the pillar-supported region with cultured cells to be stretched biaxially. The optically clear device and pillar-based mechanism of operation enables imaging on standard laboratory microscopes. Straightforward fabrication utilizes off-the-shelf components, soft lithography techniques in polydimethylsiloxane and laser ablation of acrylic sheets. Proof of compatibility with basic biological assays and standard imaging equipment were accomplished by straining C2C12 skeletal myoblasts on the device for 6 h. At higher strains, cells and actin stress fibers realign with a circumferential preference.

  11. Radionuclide annular single crystal scintillator camera with rotating collimator

    Genna, S.; Pang, S.-C.

    1986-04-22

    A radionuclide emission tomography camera is described for sensing gamma ray emissions from a source within the field of view consisting of: a fixed, position-sensitive detector means, responsive to the gamma ray emissions and surrounding the field of view for detecting the contact position and the trajectory from which a gamma ray emission originates, the fixed, position-sensitive detector including a single continuous stationary scintillation crystal; rotatable collimator means, disposed between the fixed, position-sensitive detecto means and the field of view, and including at least one array of collimator elements, for restricting and collimating the gamma ray emissions; and means for rotating the collimator means relative to the fixed, position-sensitive detector, for exposing different sections of the position-sensitive detector to the gamma ray emissions in order to view the source from different angles.

  12. Coupling in reflector arrays

    Appel-Hansen, Jørgen

    1968-01-01

    In order to reduce the space occupied by a reflector array, it is desirable to arrange the array antennas as close to each other as possible; however, in this case coupling between the array antennas will reduce the reflecting properties of the reflector array. The purpose of the present communic...

  13. Parabolic antennas, and circular slot arrays, for the generation of Non-Diffracting Beams of Microwaves

    Zamboni-Rached, Michel

    2014-01-01

    We propose in detail Antennas for generating Non-Diffracting Beams of Microwaves, for instance with frequencies of the order of 10 GHz, obtaining fair results even when having recourse to realistic apertures endowed with reasonable diameters. Our first proposal refers mainly to sets of suitable annular slits, having in mind various possible applications, including remote sensing. Our second proposal --which constitutes one of the main aims of this paper-- refers to the alternative, rather simple, use of a Parabolic Reflector, illuminated by a spherical wave source located on the paraboloid axis but slightly displaced with respect to the Focus of the Paraboloid. Such a parabolic reflector yields "extended focus" (non-diffracting) beams. [OCIS codes: 999.9999; 070.7545; 050.1120; 280.0280; 050.1755; 070.0070; 200.0200. Keywords: Non-Diffracting Waves; Microwaves; Remote sensing; Annular Arrays; Bessel beams; Extended focus; Reflecting paraboloids; Parabolic reflectors; Parabolic antennas].

  14. Numerical Analysis of Slow-Wave Instabilities in Oversized Sinusoidaly Corrugated Waveguide Driven by Finitely Thick Annular Electron Beam

    Otubo, Kosuke; Ogura, Kazuo; Yamakawa, Mitsuhisa; Takashima, Yusuke

    2010-01-01

    Three kinds of models are used for beam instability analyses: those based on a solid beam, an infinitesimally thin annular beam, and a finitely thick annular beam. In high-power experiments, the electron beam is an annulus of finite thickness. In this paper, a numerical code for a sinusoidally corrugated waveguide with a finitely thick annular beam is presented and compared with other models. Our analysis is based on a new version of the self-consistent linear theory that takes into account t...

  15. Assessment of the Preservation of Impact Residues in Stardust Analogue Craters Using Advanced EDX Imagery with an Annular SDD

    Salge, T.; Kearsley, A. T.; Price, M. C.; Burchell, M. J.; Cole, M. J.

    2016-08-01

    Low voltage SEM/EDX analysis with an annular SDD can show relationships between even tiny impact residues throughout complex crater shapes. The technique should be used as a preliminary reconnaissance method on all Stardust cometary dust craters.

  16. High-Flux Femtosecond X-Ray Emission from Controlled Generation of Annular Electron Beams in a Laser Wakefield Accelerator.

    Zhao, T Z; Behm, K; Dong, C F; Davoine, X; Kalmykov, S Y; Petrov, V; Chvykov, V; Cummings, P; Hou, B; Maksimchuk, A; Nees, J A; Yanovsky, V; Thomas, A G R; Krushelnick, K

    2016-08-26

    Annular quasimonoenergetic electron beams with a mean energy in the range 200-400 MeV and charge on the order of several picocoulombs were generated in a laser wakefield accelerator and subsequently accelerated using a plasma afterburner in a two-stage gas cell. Generation of these beams is associated with injection occurring on the density down ramp between the stages. This well-localized injection produces a bunch of electrons performing coherent betatron oscillations in the wakefield, resulting in a significant increase in the x-ray yield. Annular electron distributions are detected in 40% of shots under optimal conditions. Simultaneous control of the pulse duration and frequency chirp enables optimization of both the energy and the energy spread of the annular beam and boosts the radiant energy per unit charge by almost an order of magnitude. These well-defined annular distributions of electrons are a promising source of high-brightness laser plasma-based x rays.

  17. Use of an annular chamber for testing thermal preference of westslope cutthroat trout and rainbow trout

    McMahon, T.E.; Bear, E.A.; Zale, A.V.

    2008-01-01

    Remaining populations of westslope cutthroat trout (Oncorhynchus clarkii lewisi) in western North America are primarily confined to cold headwaters whereas nonnative rainbow trout (Oncorhynchus mykiss) predominate in warmer, lower elevation stream sections historically occupied by westslope cutthroat trout. We tested whether differing thermal preferences could account for the spatial segregation observed in the field. Thermal preferences of age-1 westslope cutthroat trout and rainbow trout (125 to 150 mm total length) were assessed in the laboratory using a modified annular preference chamber at acclimation temperatures of 10, 12, 14, and 16??C Final preferred temperature of westslope cutthroat trout (14.9??C) was similar to that of rainbow trout (14.8??C) when tested in a thermal gradient of 11-17??C The high degree of overlap in thermal preference indicates the two species have similar thermal niches and a high potential for competition. We suggest several modifications to the annular preference chamber to improve performance in future studies.

  18. Annular shape silver lined proportional counter for on-line pulsed neutron yield measurement

    Dighe, P. M.; Das, D.

    2015-04-01

    An annular shape silver lined proportional counter is developed to measure pulsed neutron radiation. The detector has 314 mm overall length and 235 mm overall diameter. The central cavity of 150 mm diameter and 200 mm length is used for placing the neutron source. Because of annular shape the detector covers >3π solid angle of the source. The detector has all welded construction. The detector is developed in two halves for easy mounting and demounting. Each half is an independent detector. Both the halves together give single neutron pulse calibration constant of 4.5×104 neutrons/shot count. The detector operates in proportional mode which gives enhanced working conditions in terms of dead time and operating range compared to Geiger Muller based neutron detectors.

  19. Annular core for Modular High-Temperature Gas-Cooled Reactor (MHTGR)

    Turner, R.F.; Baxter, A.M.; Stansfield, O.M.; Vollman, R.E.

    1987-08-01

    The active core of the 350 MW(t) MHTGR is annular in configuration, shaped to provide a large external surface-to-volume ratio for the transport of heat radially to the reactor vessel in case of a loss of coolant flow. For a given fuel temperature limit, the annular core provides approximately 40% greater power output over a typical cylindrical configuration. The reactor core is made up of columns of hexagonal blocks, each 793-mm high and 360-mm wide. The active core is 3.5 m in o.d., 1.65 m in i.d., and 7.93-m tall. Fuel elements contain TRISO-coated microspheres of 19.8% enriched uranium oxycarbide and of fertile thorium oxide. The core is controlled by 30 control rods which enter the inner and outer side reflectors from above.

  20. Annular core for the Modular High-Temperature Gas-cooled Reactor (MHTGR)

    Turner, R.F.; Baxter, A.M.; Stansfield, O.M.; Vollman, R.E.

    The active core of the 350 MW(t) MHTGR is annular in configuration, shaped to provide a large external surface-to-volume ratio for the transport of heat radially to the reactor vessel in case of a loss of coolant flow. For a given fuel temperature limit, the annular core provides approximately 40% greater power output over a typical cylindrical configuration. The reactor core is made up to columns of hexagonal blocks, each 793 mm high and 360 mm wide. The active core is 3.5 m in outside diameter, 1.65 m in inside diameter, and 7.93 m tall. Fuel elements contain TRISO-coated microspheres of 19.8% enriched uranium oxycarbide and of fertile thorium oxide. The core is controlled by 30 control rods which enter the inner and outer side reflectors from above.

  1. Annular wave packets at Dirac points and probability oscillation in graphene

    Luo, Ji; Valencia, Daniel

    2011-01-01

    Wave packets in graphene whose central wave vector is at Dirac points are investigated by numerical calculations. Starting from an initial Gaussian function, these wave packets form into annular peaks that propagate to all directions like ripple-rings on water surface. At the beginning, electronic probability alternates between the central peak and the ripple-rings and transient oscillation occurs at the center. As time increases, the ripple-rings propagate at the fixed Fermi speed, and their widths remain unchanged. The axial symmetry of the energy dispersion leads to the circular symmetry of the wave packets. The fixed speed and widths, however, are attributed to the linearity of the energy dispersion. Interference between states that respectively belong to two branches of the energy dispersion leads to multiple ripple-rings and the probability-density oscillation. In a magnetic field, annular wave packets become confined and no longer propagate to infinity. If the initial Gaussian width differs greatly fro...

  2. Selective color imaging using weighted interleaved multiple annular linear diffractive axicons.

    Bialic, Emilie; Petiton, Valéry; de Bougrenet de la Tocnaye, Jean-Louis

    2012-07-10

    Annular linear diffractive axicons are optical devices providing chromatic imaging over an extended depth of focus when illuminated by a white light. To improve their low radiometric performance, multiple annular linear diffractive axicons (MALDAs) have been introduced. Their chromatic properties are well known and constrained by dispersion laws. A first attempt to freely combine colors or wavelength bands has been obtained with interleaved MALDAs (I_MALDAs). However, such optics do not provide a full decoupling between wavelength combination and brightness control required in the CIE color space to address any colors. We present here a new category of I_MALDA providing this capability when illuminated by a white source containing tristimulus (red/green/blue) values. We assess both theoretically and experimentally imaging qualities of such optics with respect to two different interleaving techniques and suggest some potential applications, in particular in the field of anticounterfeit and authentication techniques.

  3. 3D analytical solution for a rotating transversely isotropic annular plate of functionally graded materials

    CHEN Jiang-ying; CHEN Wei-qiu

    2007-01-01

    The analytical solution for an annular plate rotating at a constant angular velocity is derived by means of direct displacement method from the elasticity equations for axisymmetric problems of functionally graded transversely isotropic media.The displacement components are assumed as a linear combination of certain explicit functions of the radial coordinate, with seven undetermined coefficients being functions of the axial coordinate z. Seven equations governing these z-dependent functions are derived and solved by a progressive integrating scheme. The present solution can be degenerated into the solution of a rotating isotropic functionally graded annular plate. The solution also can be degenerated into that for transversely isotropic or isotropic homogeneous materials. Finally, a special case is considered and the effect of the material gradient index on the elastic field is illustrated numerically.

  4. Filamentation of an annular laser beam with a vortex phase dislocation in fused silica

    Vasil'ev, E. V.; Shlenov, S. A.

    2016-11-01

    The filamentation of a femtosecond laser pulse in fused silica has been numerically investigated for the case of an annular beam with a phase singularity at a wavelength of 800 {\\text{nm}}. The spatiotemporal propagation dynamics of the pulse and the transformation of its frequency-angular spectra are analysed. It is shown that a tubular structure with a radius of 3 - 4 \\unicode{956}{\\text{m}}, peak intensity of about 2.4 × 1013 {\\text{W cm}}-2, and maximum plasma density on the order of 1020 {\\text{cm}}-3 is formed in the nonlinear focus; the length of this structure significantly exceeds the waist length in the linear case. The results of the analysis are compared with the data obtained for an annular beam free of phase dislocations and for a Gaussian beam.

  5. Thermal performance of functionally graded parabolic annular fins having constant weight

    Gaba, Vivek Kumar; Tiwari, Anil Kumar; Bhowmick, Shubhankar [National Institute of Technology Raipur, Raipur (India)

    2014-10-15

    The proposed work reports the performance of parabolic annular fins of constant weight made of functionally graded materials. The work involves computation of temperature gradient, efficiency and effectiveness of such fins and compares the performances for different functionally graded parabolic fin profiles obtained by varying grading parameters and profile parameters respectively keeping the weight of the fins constant. The functional grading of thermal conductivity is based on a power function of radial co-ordinate which consists of parameters, namely grading parameters, varying which different grading combinations are studied. A general second order ordinary differential equation has been derived for all the profiles and material grading. The efficiency and effectiveness of the annular fins of different profile and grading combinations have been calculated and plotted and the results reveal the dependence of fin performance on profile and grading parameter.

  6. The Springtime North Asia Cyclone Activity Index and the Southern Annular Mode

    YUE Xu; WANG Huijun

    2008-01-01

    The relationship between the North Asia cyclone (NAC) activity and the Southern Annular Mode (SAM) is documented in this research. The definition of the NAC index (NACI) is based on the atmospheric relative vorticity in North Asia. The analysis yields a significant positive correlation between previous winter Southern Annular Mode index (SAMI) and spring NACI in the interannual variability, with a correlation coefficient of 0.51 during 1948-2000. Analysis of the NAC-related and SAM-related atmospheric general circulation variability demonstrates such a relationship. The study further reveals that when the winter SAM becomes strong, the springtime atmospheric convection in tropical western Pacific will intensify and the local Hadley circulation will be strengthened. As a result, the abnormal subsiding motion over South China makes the temperature gradient intensified in the low level and strengthens the jet in the high level, both of which are beneficial to the development of NAC activity.

  7. A New Approach to Designing the S-Shaped Annular Duct for Industrial Centrifugal Compressor

    Ivan Yurko

    2014-01-01

    Full Text Available The authors propose an analytical method for designing the inlet annular duct for an industrial centrifugal compressor using high-order Bezier curves. Using the design of experiments (DOE theory, the three-level full factorial design was developed for determination of influence of the dimensionless geometric parameters on the output criteria. Numerical research was carried out for determination of pressure loss coefficients and velocity swirl angles using the software system ANSYS CFX. Optimal values of the slope for a wide range of geometric parameters, allowing minimizing losses in the duct, have been found. The study has used modern computational fluid dynamics techniques to develop a generalized technique for future development of efficient variable inlet guide vane systems. Recommendations for design of the s-shaped annular duct for industrial centrifugal compressor have been given.

  8. Do split and displacement sudden stratospheric warmings have different annular mode signatures?

    Maycock, Amanda; Hitchcock, Peter

    2016-04-01

    Sudden stratospheric warmings (SSWs) contribute to intraseasonal tropospheric forecasting skill due to their surface impacts. Recent studies suggest these impacts depend upon whether the polar vortex splits or is displaced during the SSW. We analyse the annular mode signatures of SSWs in a 1000 year IPSL-CM5A-LR simulation. Although small differences in the mean surface Northern Annular Mode (NAM) index following splits and displacements are found, the sign is not consistent for two independent SSW algorithms, and over 50 events are required to distinguish the responses. We use the winter-time correlation between extratropical lower stratospheric wind anomalies and the surface NAM index as a metric for two-way stratosphere-troposphere coupling, and find that the differences between splits and displacements, and between classification methodologies, can be simply understood in terms of their mean stratospheric wind anomalies. Predictability studies should therefore focus on understanding the factors that determine the persistence of these anomalies following SSWs.

  9. Annular flow of cement slurries; Escoamento anular de pastas de cimento

    Silva, Maria das Gracas Pena; Martins, Andre Leibsohn; Oliveira, Antonio Augusto J. de [PETROBRAS, Rio de Janeiro (Brazil). Centro de Pesquisas. Setor de Tecnologia de Perfuracao

    1989-12-31

    This paper considers the analysis of laminar, transitory and turbulent flow regimes of cement slurries of various compositions flowing in annular sections. It is an experimental study to evaluate the performance of dozens of equations found in the literature that reflect the rheological behavior of non-Newtonian fluids, the dimensioning of annular sections, the delimitation of the transitory zone and the estimative of friction losses in the turbulent flow regime. A large-scale physical simulator (SHS-Surface Hydraulic Simulator), was designed and constructed at the PETROBRAS Research Center in order to obtain flow parameters. A computer program capable of analysing and drawing conclusions from the behavior of non-Newtonian fluids flowing in different geometries and energetic conditions was also developed. These were considered as essential stages for the development of the project. (author) 17 refs., 9 figs., 18 tabs.

  10. AXISYMMETRIC BENDING OF TWO-DIRECTIONAL FUNCTIONALLY GRADED CIRCULAR AND ANNULAR PLATES

    Guojun Nie; Zheng Zhong

    2007-01-01

    Assuming the material properties varying with an exponential law both in the thickness and radial directions, axisymmetric bending of two-directional functionally graded circular and annular plates is studied using the semi-analytical numerical method in this paper. The deflections and stresses of the plates are presented. Numerical results show the well accuracy and convergence of the method. Compared with the finite element method, the semi-analytical numerical method is with great advantage in the computational efficiency. Moreover, study on axisymmetric bending of two-directional functionally graded annular plate shows that such plates have better performance than those made of isotropic homogeneous materials or one-directional functionally graded materials. Two-directional functionally graded material is a potential alternative to the one-directional functionally graded material. And the integrated design of materials and structures can really be achieved in two-directional functionally graded materials.

  11. Gas turbine structural mounting arrangement between combustion gas duct annular chamber and turbine vane carrier

    Wiebe, David J.; Charron, Richard C.; Morrison, Jay A.

    2016-10-18

    A gas turbine engine ducting arrangement (10), including: an annular chamber (14) configured to receive a plurality of discrete flows of combustion gases originating in respective can combustors and to deliver the discrete flows to a turbine inlet annulus, wherein the annular chamber includes an inner diameter (52) and an outer diameter (60); an outer diameter mounting arrangement (34) configured to permit relative radial movement and to prevent relative axial and circumferential movement between the outer diameter and a turbine vane carrier (20); and an inner diameter mounting arrangement (36) including a bracket (64) secured to the turbine vane carrier, wherein the bracket is configured to permit the inner diameter to move radially with the outer diameter and prevent axial deflection of the inner diameter with respect to the outer diameter.

  12. Effect of the geometry of workpiece on polishing velocity in free annular polishing

    Quantang Fan; Jianqiang Zhu; Bao'an Zhang

    2007-01-01

    Base on Coulomb friction model, the workpieces with different geometry rotating in free annular polishing are simulated. From simulation, the following conclusions are drawn. The angular velocity of workpiece is higher than that of polishing pad if the ring rotates uncontrolled in free annular polishing. The circular workpiece can synchronize with polishing pad through controlling the rotation of ring, which depends on the radii of ring and workpiece, the friction coefficients of polishing pad-workpiece and ring-workpiece,and the angular velocity of polishing pad. The workpiece with sharp corner cannot contact with the ring contiguously, which causes the contact state changing and the angular velocity of workpiece fluctuating ceaselessly, and this type of workpiece should be controlled with clamp to rotate synchronistically with the polishing pad.

  13. The effect of pressure on annular flow pressure drop in a small pipe

    de Bertodano, M.A.L.; Beus, S.G.; Shi, Jian-Feng

    1996-09-01

    New experimental data was obtained for pressure drop and entrainment for annular up-flow in a vertical pipe. The 9.5 mm. pipe has an L/D ratio of 440 to insure fully developed annular flow. The pressure ranged from 140 kPa to 660 kPa. Therefore the density ratio was varied by a factor of four approximately. This allows the investigation of the effect of pressure on the interfacial shear models. Gas superficial velocities between 25 and 126 m/s were tested. This extends the range of previous data to higher gas velocities. The data were compared with well known models for interfacial shear that represent the state of the art. Good results were obtained when the model by Asali, Hanratty and Andreussi was modified for the effect of pressure. Furthermore an equivalent model was obtained based on the mixing length theory for rough pipes. It correlates the equivalent roughness to the film thickness.

  14. Experimental research on dryout point of flow boiling in narrow annular channels

    2006-01-01

    An experimental research on the dryout point of flow boiling in narrow annular channels under low mass flux with 1.55 mm and 1.05 mm annular gap, respectively, is conducted. Distilled water is used as working fluid and the range of pressure is limited within 2.0~4.0 MPa and that of mass flux is 26.0~69.0 kg·m-2·s-1. The relation of critical heat flux (CHF) and critical qualities with mass flux and pressure are revealed. It is found that the critical qualities decrease with the increasing mass flux and increase with the increasing inlet qualities in externally heated annuli.Under the same conditions, critical qualities in the outer tube are always larger than those in the inner tube. The appearance of dryout point in bilaterally heated narrow annuli can be judged according to the ratio of qo/qi.

  15. ThO{sub 2}-UO{sub 2} annular pins for high burnup fuels

    Caner, Marc; Dugan, Edward T

    2000-06-01

    The main purpose of this work is to investigate the use of annular fuel pins (particularly pins containing thorium dioxide) for high burnup fuel. The following parameters were evaluated and compared between postulated mixed thorium-uranium dioxide standard and annular (9% void fraction) type fuel assemblies, as a function of burnup: the infinite multiplication factor, the uranium and plutonium isotopic compositions, the fuel temperature coefficient of reactivity and the conversion ratio. We used the SCALE-4.3 code system. The calculation method consisted in obtaining actinide and fission product number densities as functions of assembly burnup, by means of a 1-D transport calculation combined with a 0-D burnup calculation. These number densities were then used in a 3-D Monte Carlo code for obtaining k{sub {infinity}} from two-dimensional-symmetry 'snapshots'.

  16. Fully developed MHD natural convection flow in a vertical annular microchannel: An exact solution

    Basant K. Jha

    2015-07-01

    Full Text Available An exact solution of steady fully developed natural convection flow of viscous, incompressible, electrically conducting fluid in a vertical annular micro-channel with the effect of transverse magnetic field in the presence of velocity slip and temperature jump at the annular micro-channel surfaces is obtained. Exact solution is expressed in terms of modified Bessel function of the first and second kind. The solution obtained is graphically represented and the effects of radius ratio (η, Hartmann number (M, rarefaction parameter (βvKn, and fluid–wall interaction parameter (F on the flow are investigated. During the course of numerical computations, it is found that an increase in Hartmann number leads to a decrease in the fluid velocity, volume flow rate and skin friction. Furthermore, it is found that an increase in curvature radius ratio leads to an increase in the volume flow rate.

  17. THE PERTURBATION SOLUTIONS OF THE FLOW IN A ROTATING CURVED ANNULAR PIPE

    2001-01-01

    In this paper, the flow in a rotating curved annular pipe isexamined by a perturbation method. A second order perturbation solution is presented. The characteristics of the secondary flow and the axial flow are studied in detail.The study indicates that the loops of the secondary flow are more complex than those in a curved annular pipe without rotation and its numbers depend on the ratio of the Coriolis force to centrifugal force F. As F ≈- 1 , the secondary flow has eight loops and its intensity reaches the minimum value, and the distribution of the axial flow is like that of the Poiseuille flow. The position of the maximum axial velocity is pushed to either outer bend or inner bend, which is also determined by F.

  18. LDA measurement of the passage flow field in an annular airfoil cascade

    Stauter, R. C.; Fleeter, S.

    1987-01-01

    Models to predict the complex three-dimensional flow through turbomachine blade rows are being developed. To verify these models and direct necessary refinements, it is necessary that predictions be correlated with data obtained in experiments which model the fundamental three-dimensional blade row flow phenomena. This paper describes a series of experiments performed in a large scale, subsonic, annular cascade facility specifically designed to provide such data. In particular, the effect of incidence angle on the three-dimensional passage flow field through an annular cascade of cambered airfoils is investigated and quantified, accomplished by obtaining detailed and expensive LDA data. These data demonstrate and quantify the development of the passage vortices through the airfoil passage and their strong interaction with the endwall boundary layers.

  19. Experimental Study on the Characteristics of Liquid Layer and Disturbance Waves in Horizontal Annular Flow

    1999-01-01

    The mechanism for transporting liquid from the bottom of the pipe to the top still to be established in the prediction of the film thickness distribution in horizontal annular two-phase flow.To resolve this issue,using five parallel-wire conductance probes,time records of local liquid film thickness at five circumferential positions were collected.The characteristics of circumferential liquid film thickness profiles and its variation with gas and liquid velocities were obtained.The basic features of probability distribution function,probability density function,auto-correlation,cross-correlation and power spectrum density function of the disturbance waves in annular flow were studied respectively.The characterstics of circumferential profiles of disturbance waves and its variation with gas and liquid velocities were presented.

  20. The quantum spectral analysis of the two-dimensional annular billiard system

    Zhang Yan-Hui; Zhang Ji-Ouan; Xu Xue-You; Lin Sheng-Lu

    2009-01-01

    Based on the extended closed-orbit theory together with spectral analysis, this paper studies the correspondence between quantum mechanics and the classical counterpart in a two-dimeusional annular billiard. The results demonstrate that the Fourier-transformed quantum spectra are in very good accordance with the lengths of the classical ballistic trajectories, whereas spectral strength is intimately associated with the shapes of possible open orbits connecting arbitrary two points in the annular cavity. This approach facilitates an intuitive understanding of basic quantum features such as quantum interference, locations of the wavefunctions, and allows quantitative calculations in the range of high energies, where full quantum calculations may become impractical in general. This treatment provides a thread to explore the properties of microjunction transport and even quantum chaos under the much more general system.

  1. Design of a small Annular Linear Induction Electromagnetic Pump - Simulation and Experiment

    Yong-Lin, Ma; Yan-Jiang, Chen; Tao, Jiang; Shu-Qing, Xing

    2015-01-01

    International audience; An annular linear induction electromagnetic pump (ALIP) is used for pumping liquid tin alloy with a flow rate and developed pressure of 17l /min and 0.5bar respectively. The electromagnetic force, flux density and inducted current density are calculated using a by finite element method (FEM) the various design variables. The performance of ALIP is tested with liquid tin for various melting point temperatures. Results show that pressure increases as electromagnetic forc...

  2. Tunable extended depth of field using a liquid crystal annular spatial filter.

    Klapp, Iftach; Solodar, Asi; Abdulhalim, Ibrahim

    2014-03-15

    A tunable extended depth of field (EDOF) imaging is presented using temporal multiplexing and a low-cost eight-ring, annular liquid crystal spatial light modulator. By changing between different phase profiles in the pupil plane of a lens we perform several levels of EDOF. Using these levels as a "database" it is shown by temporal multiplexing how to decompose tunable levels of EDOF.

  3. Effects of Nonuniform Blade Pitch on the Flow Through an Annular Turbine Nozzle

    1995-01-01

    This paper discusses flow measurement results both upstream and downstream of a transonic annular gas turbine nozzle with a nonuniform pitch. The downstream measurements are performed in the plane where the leading edge of the rotor blade is located in the gas turbine. The experiments were performed using total pressure probes and wall static pressure taps. The pitch variation modifies the flow field both upstream and downstream of the nozzle, although the experiments show that the effect ...

  4. Microwave generation enhancement of X-band CRBWO by use of coaxial dual annular cathodes

    Yan Teng; Jun Sun; Changhua Chen; Hao Shao

    2013-01-01

    This paper presents an approach that greatly enhances both the output power and the conversion efficiency of the coaxial relativistic backward wave oscillator (CRBWO) by using coaxial dual annular cathodes, which increases the diode current rather than the diode voltage. The reasons for the maladjustment of CRBWO under a high diode voltage are analyzed theoretically. It is found that by optimization of the diode structure, the shielding effect of the space charge of the outer beams on the inn...

  5. Tricuspid annular plane systolic excursion and response to cardiac resynchronization therapy

    Kjaergaard, Jesper; Ghio, Stefano; St John Sutton, Martin;

    2011-01-01

    The aims of this study were to evaluate tricuspid annular plane systolic excursion (TAPSE) as a predictor of left ventricular (LV) reverse remodeling and clinical benefit of cardiac synchronization therapy (CRT) and to evaluate the effect of CRT on TAPSE in patients with mildly symptomatic systolic...... heart failure as a substudy of the REsyncronization reVErses Remodeling in Systolic left vEntricular dysfunction (REVERSE) trial....

  6. Droplet entrainment correlation in vertical upward co-current annular two-phase flow

    Sawant, Pravin [Purdue University, School of Nuclear Engineering, 400 Central Dr., West Lafayette, IN 47907-2017 (United States)], E-mail: psawant@purdue.edu; Ishii, Mamoru [Purdue University, School of Nuclear Engineering, 400 Central Dr., West Lafayette, IN 47907-2017 (United States); Mori, Michitsugu [Tokyo Electric Power Co., Inc., R and D Center, 4-1 Egasaki-cho, Tsurumi-ku, Yokohama 230-8510 (Japan)], E-mail: michitsugu.mori@tepco.co.jp

    2008-06-15

    Upward annular two-phase flow in a vertical tube is characterized by the presence of liquid film on the tube wall and entrained droplet laden gas phase flowing through the tube core. Entrainment fraction in annular flow is defined as a fraction of the total liquid flow flowing in the form of droplets through the central gas core. Its prediction is important for the estimation of pressure drop and dryout in annular flow. In the following study, measurements of entrainment fraction have been obtained in vertical upward co-current air-water annular flow covering wide ranges of pressure and flow conditions. Comparison of the experimental data with the existing entrainment fraction prediction correlations revealed their inadequacies in simulating the trends observed under high flow and high pressure conditions. Furthermore, several correlations available in the literature are implicit and require iterative calculations. Analysis of the experimental data showed that the non-dimensional numbers, Weber number (We = {rho}{sub g}{sup 2}D/{sigma}({delta}{rho}/{rho}{sub g}){sup 1/4}) and liquid phase Reynolds number (Re{sub f} = {rho}{sub f}D/{mu}{sub f}), successfully collapse the data. In view of this, simple, explicit correlation was developed based on these non-dimensional numbers for the prediction of entrainment fraction. The new correlation successfully predicted the trends under the high flow and high pressure conditions observed in the current experimental data and the data available in open literature. However, in order to use the proposed correlation it is necessary to predict the maximum possible entrainment fraction (or limiting entrainment fraction). In the current analysis, an experimental data based correlation was used for this purpose. However, a better model or correlation is necessary for the maximum possible entrainment fraction. A theoretical discussion on the mechanism and modeling of the maximum possible entrainment fraction

  7. Development of electron optical system using annular pupils for scanning transmission electron microscope by focused ion beam

    Matsutani, Takaomi, E-mail: matutani@ele.kindai.ac.jp [Kinki University, 3-4-1 Kowakae, Higashiosaka, Osaka 577-8502 (Japan); Yasumoto, Tsuchika; Tanaka, Takeo [Osaka Sangyo University, 3-1-1 Nakagaito, Daito, Osaka 574-8530 (Japan); Kawasaki, Tadahiro; Ichihashi, Mikio [Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Ikuta, Takashi [Osaka Electro-Communication University, 18-8 Hatsu-cho, Neyagawa, Osaka 572-8530 (Japan)

    2012-02-01

    Annular pupils for electron optics were produced using a focused ion beam (FIB), enabling an increase in the depth of focus and allowing for aberration-free imaging and separation of the amplitude and phase images in a scanning transmission electron microscope (STEM). Simulations demonstrate that an increased focal depth is advantageous for three-dimensional tomography in the STEM. For a 200 kV electron beam, the focal depth is increased to approximately 100 nm by using an annular pupil with inner and outer semi-angles of 29 and 30 mrad, respectively. Annular pupils were designed with various outer diameters of 40-120 {mu}m and the inner diameter was designed at 80% of the outer diameter. A taper angle varying from 1 Degree-Sign to 20 Degree-Sign was applied to the slits of the annular pupils to suppress the influence of high-energy electron scattering. The fabricated annular pupils were inspected by scanning ion beam microscopy and scanning electron microscopy. These annular pupils were loaded into a STEM and no charge-up effects were observed in the scintillator projection images recorded by a CCD camera.

  8. Laser Doppler velocimeter measurements and laser sheet imaging in an annular combustor model. M.S. Thesis, Final Report

    Dwenger, Richard Dale

    1995-01-01

    An experimental study was conducted in annular combustor model to provide a better understanding of the flowfield. Combustor model configurations consisting of primary jets only, annular jets only, and a combination of annular and primary jets were investigated. The purpose of this research was to provide a better understanding of combustor flows and to provide a data base for comparison with computational models. The first part of this research used a laser Doppler velocimeter to measure mean velocity and statistically calculate root-mean-square velocity in two coordinate directions. From this data, one Reynolds shear stress component and a two-dimensional turbulent kinetic energy term was determined. Major features of the flowfield included recirculating flow, primary and annular jet interaction, and high turbulence. The most pronounced result from this data was the effect the primary jets had on the flowfield. The primary jets were seen to reduce flow asymmetries, create larger recirculation zones, and higher turbulence levels. The second part of this research used a technique called marker nephelometry to provide mean concentration values in the combustor. Results showed the flow to be very turbulent and unsteady. All configurations investigated were highly sensitive to alignment of the primary and annular jets in the model and inlet conditions. Any imbalance between primary jets or misalignment of the annular jets caused severe flow asymmetries.

  9. Study of optical reflectance properties in 1D annular photonic crystal containing double negative (DNG) metamaterials

    Srivastava, Sanjeev K.; Aghajamali, Alireza

    2016-05-01

    Theoretical investigation of photonic band gaps or reflection bands in one-dimensional annular photonic crystal (APC) containing double negative (DNG) metamaterials and air has been presented. The proposed structure consists of the alternate layers of dispersive DNG material and air immersed in free space. In order to study photonic band gaps we obtain the reflectance spectrum of the annular PC by employing the transfer matrix method (TMM) in the cylindrical waves for both TE and TM polarizations. In this work we study the effect of azimuthal mode number (m) and starting radius (ρ0) on the three band gaps viz. zero averaged refractive index (zero-nbar) gap, zero permittivity (zero- ε) and zero permeability (zero- μ) gaps. It is found that for m ≥ 1 , zero- μ gap appears in TE mode and zero- ε gap appears in TM mode. The width of both zero- μ and zero- ε gap increases by increasing m values, but the enhancement of zero- μ gap is more appreciable. Also, the effect of ρ0 on the three band gaps (reflection bands) of annular PC structure at the given m-number has been studied, for both TE and TM polarizations. The result shows that in both polarizations zero- ε and zero- μ gaps decreases when ρ0 increases, whereas zero-nbar gap remains invariant.

  10. Closed-form solution for free vibration of piezoelectric coupled annular plates using Levinson plate theory

    Hosseini Hashemi, Sh.; Es'haghi, M.; Karimi, M.

    2010-04-01

    Free vibration analysis of annular moderately thick plates integrated with piezoelectric layers is investigated in this study for different combinations of soft simply supported, hard simply supported and clamped boundary conditions at the inner and outer edges of the annular plate on the basis of the Levinson plate theory (LPT). The distribution of electric potential along the thickness direction in the piezoelectric layer is assumed as a sinusoidal function so that the Maxwell static electricity equation is approximately satisfied. The differential equations of motion are solved analytically for various boundary conditions of the plate. In this study the closed-form solution for characteristic equations, displacement components of the plate and electric potential are derived for the first time in the literature. To demonstrate the accuracy of the present solution, comparison studies is first carried out with the available data in the literature and then natural frequencies of the piezoelectric coupled annular plate are presented for different thickness-radius ratios, inner-outer radius ratios, thickness of piezoelectric, material of piezoelectric and boundary conditions. Present analytical model provides design reference for piezoelectric material application, such as sensors, actuators and ultrasonic motors.

  11. A shaped annular beam tri-heterodyne confocal microscope with good anti-environmental interference capability

    Zhao Wei-Qian; Feng Zheng-De; Qiu Li-Rong

    2007-01-01

    A shaped annular beam tri-heterodyne confocal microscope has been proposed to improve the anti-environmental interference capability and the resolution of a confocal microscope. It simultaneously detects far-, on-, and near-focus signals with given phase differences by dividing the measured light path of the confocal microscope into three sub-paths (signals). Pair-wise real-time heterodyne subtraction of the three signals is used to improve the anti-environmental interference capability, axial resolution, and linearity; and a shaped annular beam super-resolution technique is used to improve lateral resolution. Theoretical analyses and preliminary experiments indicate that an axial resolution of about 1 nm can be achieved with a shaped annular beam tri-heterodyne confocal microscope and its lateral resolution can be better than 0.2μm for λ= 632.8 nm, the numerical aperture of the lens of the microscope is NA = 0.85, and the normalized radius ε= 0.5.

  12. Crossover of the thermal escape problem in annular spatially distributed systems.

    Fedorov, Kirill G; Pankratov, Andrey L

    2009-12-31

    The computer simulations of fluctuational dynamics of an annular system governed by the sine-Gordon model with a white noise source are performed. It is demonstrated that the mean escape time (MET) of a phase string for an annular structure can be much larger than for a linear one and has a strongly pronounced maximum as a function of system's length. The location of the MET maximum roughly equals the size of the kink-antikink pair, which leads to evidence of a spatial crossover between two dynamical regimes: when the phase string escapes over the potential barrier as a whole and when the creation of kink-antikink pairs is the main mechanism of the escape process. For large lengths and in the limit of small noise intensity gamma, for both MET and inverse concentration of kinks, we observe the same dependence versus the kink energy E(k): approximately exp(2E(k)/gamma) for the annular structure and approximately exp(E(k)/gamma) for the linear one.

  13. Progress in analytical methods to predict and control azimuthal combustion instability modes in annular chambers

    Bauerheim, M.; Nicoud, F.; Poinsot, T.

    2016-02-01

    Longitudinal low-frequency thermoacoustic unstable modes in combustion chambers have been intensively studied experimentally, numerically, and theoretically, leading to significant progress in both understanding and controlling these acoustic modes. However, modern annular gas turbines may also exhibit azimuthal modes, which are much less studied and feature specific mode structures and dynamic behaviors, leading to more complex situations. Moreover, dealing with 10-20 burners mounted in the same chamber limits the use of high fidelity simulations or annular experiments to investigate these modes because of their complexity and costs. Consequently, for such circumferential acoustic modes, theoretical tools have been developed to uncover underlying phenomena controlling their stability, nature, and dynamics. This review presents recent progress in this field. First, Galerkin and network models are described with their pros and cons in both the temporal and frequency framework. Then, key features of such acoustic modes are unveiled, focusing on their specificities such as symmetry breaking, non-linear modal coupling, forcing by turbulence. Finally, recent works on uncertainty quantifications, guided by theoretical studies and applied to annular combustors, are presented. The objective is to provide a global view of theoretical research on azimuthal modes to highlight their complexities and potential.

  14. CFD Study of an Annular-Ducted Fan Lift System for VTOL Aircraft

    Yun Jiang

    2015-09-01

    Full Text Available The present study aimed at assessing a novel annular-ducted fan lift system for VTOL aircraft through computational fluid dynamics (CFD simulations. The power and lift efficiency of the lift fan system in hover mode, the lift and drag in transition mode, the drag and flight speed of the aircraft in cruise mode and the pneumatic coupling of the tip turbine and jet exhaust were studied. The results show that the annular-ducted fan lift system can have higher lift efficiency compared to the rotor of the Apache helicopter; the smooth transition from vertical takeoff to cruise flight needs some extra forward thrust to overcome a low peak of drag; the aircraft with the lift fan system enclosed during cruise flight theoretically may fly faster than helicopters and tiltrotors based on aerodynamic drag prediction, due to the elimination of rotor drag and compressibility effects on the rotor blade tips; and pneumatic coupling of the tip turbine and jet exhaust of a 300 m/s velocity can provide enough moment to spin the lift fan. The CFD results provide insight for future experimental study of the annular-ducted lift fan VTOL aircraft.

  15. Gamma-ray Emission from the Vela Pulsar Modeled with the Annular Gap and Core Gap

    Du, Y J; Qiao, G J; Chou, C K

    2011-01-01

    The Vela pulsar represents a distinct group of {\\gamma}-ray pulsars. Fermi {\\gamma}-ray observations reveal that it has two sharp peaks (P1 and P2) in the light curve with a phase separation of 0.42 and a third peak (P3) in the bridge. The location and intensity of P3 are energy-dependent. We use the 3D magnetospheric model for the annular gap and core gap to simulate the {\\gamma}-ray light curves, phase-averaged and phase-resolved spectra. We found that the acceleration electric field along a field line in the annular gap region decreases with heights. The emission at high energy GeV band is originated from the curvature radiation of accelerated primary particles, while the synchrotron radiation from secondary particles have some contributions to low energy {\\gamma}-ray band (0.1 - 0.3 GeV). The {\\gamma}-ray light curve peaks P1 and P2 are generated in the annular gap region near the altitude of null charge surface, whereas P3 and the bridge emission is generated in the core gap region. The intensity and loc...

  16. Computer fluid dynamics (CFD) study of a micro annular gear pump

    Stan, Liviu-Constantin; Cǎlimǎnescu, Ioan

    2016-12-01

    Micro technology makes it possible to design products simply, efficiently and sustainably and at the same time, opens up the creation of new functionalities. The field of application of the micro annular gear pumps lies in analytical instrumentation, mechanical and plant engineering, chemical and pharmaceutical process engineering as well as in new markets like fuel cells or biotechnology, organic electronics or aerospace. The purpose of this paper is to investigate by using the powerful ANSYS 16 CFX module the hydrodynamic behavior of an 8/9 teeth annular gear pump. The solving of solids evolving inside fluids was very cumbersome until the advent of the Ansys immersed solid technology. By deploying this technology for very special topics like the CFD analysis of Micro annular gear pumps, credible and reliable results may be pulled leading thus the way for more in depth studies like geometrical a functional optimization of the existing devices. This paper is a valuable guide for the professionals working in the design field of micro pumps handing them a new and powerful design tool.

  17. Predictors of right ventricular function as measured by tricuspid annular plane systolic excursion in heart failure

    Køber Lars V

    2009-11-01

    Full Text Available Abstract Introduction Tricuspid Annular Plane Systolic Excursion (TAPSE has independent prognostic value in heart failure patients but may be influenced by left ventricular (LV ejection fraction. The present study assessed the association of TAPSE and clinical factors, global and regional LV function in 634 patients admitted for symptomatic heart failure. Methods & Results TAPSE were correlated with global and regional measures of longitudinal LV function, segmental wall motion scores and measures of diastolic LV function as measured from transthoracic echocardiography. LV ejection fraction, wall motion index scores, atrio-ventricular annular plane systolic excursion of the mitral annulus were significantly related to TAPSE. Septal and posterior mitral annular plane systolic excursion (β = 0.56, p 2 = 0.28, p interaction = NS. Conclusion TAPSE is reduced with left ventricular dysfunction in heart failure patients, in particular with reduced septal longitudinal motion. TAPSE is decreased in patients with heart failure of ischemic etiology. However, the absolute reduction in TAPSE is small and seems to be of minor importance in the clinical utilization of TAPSE whether applied as a measure of right ventricular systolic function or as a prognostic factor.

  18. Modeling of annular two-phase flow using a unified CFD approach

    Li, Haipeng, E-mail: haipengl@kth.se; Anglart, Henryk, E-mail: henryk@kth.se

    2016-07-15

    Highlights: • Annular two-phase flow has been modeled using a unified CFD approach. • Liquid film was modeled based on a two-dimensional thin film assumption. • Both Eulerian and Lagrangian methods were employed for the gas core flow modeling. - Abstract: A mechanistic model of annular flow with evaporating liquid film has been developed using computational fluid dynamics (CFD). The model is employing a separate solver with two-dimensional conservation equations to predict propagation of a thin boiling liquid film on solid walls. The liquid film model is coupled to a solver of three-dimensional conservation equations describing the gas core, which is assumed to contain a saturated mixture of vapor and liquid droplets. Both the Eulerian–Eulerian and the Eulerian–Lagrangian approach are used to describe the droplet and vapor motion in the gas core. All the major interaction phenomena between the liquid film and the gas core flow have been accounted for, including the liquid film evaporation as well as the droplet deposition and entrainment. The resultant unified framework for annular flow has been applied to the steam-water flow with conditions typical for a Boiling Water Reactor (BWR). The simulation results for the liquid film flow rate show good agreement with the experimental data, with the potential to predict the dryout occurrence based on criteria of critical film thickness or critical film flow rate.

  19. Biochemical and immunohistochemical comparison of collagen in granuloma annulare and skin sarcoidosis.

    Oikarinen, A; Kinnunen, T; Kallioinen, M

    1989-01-01

    Collagen was studied by biochemical and immunohistochemical means in 5 patients with granuloma annulare (GA) and 3 with cutaneous sarcoidosis (SA). The solubility of collagen from the lesional skin in acetic acid was higher than that of collagen from unaffected skin from both patients and control subjects. Collagen concentration in the skin lesions, measured in terms of hydroxyproline content, was reduced in 3 patients with granuloma annulare and one with sarcoidosis, but the ratio of type III/I collagen was unchanged vis-à-vis non-affected skin. The collagen concentration in non-affected skin of both GA and SA-patients was also lower than in controls. The most typical immunohistochemical finding was the association of type III procollagen and fibronectin with granulomas in the lesional skin of both GA and SA cases. The activity of prolyl hydroxylase, a key enzyme in collagen biosynthesis, was markedly increased in the lesional skin, indicating that collagen synthesis in vivo was also increased. Surprisingly, collagen synthesis was not increased in cell culture studies. This could be due to cell selection as observed previously in scleroderma. Another possibility could be that various mediators released in vivo from inflammatory cells activate fibroblasts. However, when cells are subcultivated, this effect is not maintained. In conclusion, marked changes in collagen could be observed in granuloma annulare and skin sarcoidosis, reflecting increased turnover of collagen in vivo.

  20. Dynamic Response of Rub Caused by a Shedding Annular Component Happening in a Steam Turbine

    J. M. Chen

    2015-01-01

    Full Text Available Rub caused by a shedding annular component is a severe fault happening in a steam turbine, which could result in a long-term wearing effect on the shaft. The shafting abrasion defects shortened the service life and damaged the unit. To identify the fault in time, the dynamic response of rub caused by a shedding annular component was studied as follows: (I a rotor-bearing model was established based on the structural features of certain steam turbines; node-to-node contact constraint and penalty method were utilized to analyze the impact and friction; (II dynamic response of the rotor-bearing system and the shedding component was simulated with the development of rub after the component was dropping; (III fault features were extracted from the vibration near the bearing position by time-domain and frequency-domain analysis. The results indicate that the shedding annular component would not only rotate pivoting its axis but also revolve around the shaft after a period of time. Under the excitation of the contact force, the peak-peak vibration fluctuates greatly. The frequency spectrum contains two main components, that is, the working rotating frequency and revolving frequency. The same phenomenon was observed from the historical data in the field.

  1. Concentration Measurements in a Cold Flow Model Annular Combustor Using Laser Induced Fluorescence

    Morgan, Douglas C.

    1996-01-01

    A nonintrusive concentration measurement method is developed for determining the concentration distribution in a complex flow field. The measurement method consists of marking a liquid flow with a water soluble fluorescent dye. The dye is excited by a two dimensional sheet of laser light. The fluorescent intensity is shown to be proportional to the relative concentration level. The fluorescent field is recorded on a video cassette recorder through a video camera. The recorded images are analyzed with image processing hardware and software to obtain intensity levels. Mean and root mean square (rms) values are calculated from these intensity levels. The method is tested on a single round turbulent jet because previous concentration measurements have been made on this configuration by other investigators. The previous results were used to comparison to qualify the current method. These comparisons showed that this method provides satisfactory results. 'Me concentration measurement system was used to measure the concentrations in the complex flow field of a model gas turbine annular combustor. The model annular combustor consists of opposing primary jets and an annular jet which discharges perpendicular to the primary jets. The mixing between the different jet flows can be visualized from the calculated mean and rms profiles. Concentration field visualization images obtained from the processing provide further qualitative information about the flow field.

  2. Annular multiphase flow behavior during deep water drilling and the effect of hydrate phase transition

    Wang Zhiyuan; Sun Baojiang

    2009-01-01

    It is very important to understand the annular multiphase flow behavior and the effect of hydrate phase transition during deep water drilling. The basic hydrodynamic models, including mass, momentum, and energy conservation equations, were established for annular flow with gas hydrate phase transition during gas kick. The behavior of annular multiphase flow with hydrate phase transition was investigated by analyzing the hydrate-forming region, the gas fraction in the fluid flowing in the annulus, pit gain, bottom hole pressure, and shut-in casing pressure. The simulation shows that it is possible to move the hydrate-forming region away from sea floor by increasing the circulation rate. The decrease in gas volume fraction in the annulus due to hydrate formation reduces pit gain, which can delay the detection of well kick and increase the risk of hydrate plugging in lines. Caution is needed when a well is monitored for gas kick at a relatively low gas production rate, because the possibility of hydrate presence is much greater than that at a relatively high production rate. The shut-in casing pressure cannot reflect the gas kick due to hydrate formation, which increases with time.

  3. Axiom turkey genotyping array

    The Axiom®Turkey Genotyping Array interrogates 643,845 probesets on the array, covering 643,845 SNPs. The array development was led by Dr. Julie Long of the USDA-ARS Beltsville Agricultural Research Center under a public-private partnership with Hendrix Genetics, Aviagen, and Affymetrix. The Turk...

  4. Clocked combustor can array

    Kim, Won-Wook; McMahan, Kevin Weston; Srinivasan, Shiva Kumar

    2017-01-17

    The present application provides a clocked combustor can array for coherence reduction in a gas turbine engine. The clocked combustor can array may include a number of combustor cans positioned in a circumferential array. A first set of the combustor cans may have a first orientation and a second set of the combustor cans may have a second orientation.

  5. Prediction of amount of entrained droplets in vertical annular two-phase flow

    Sawant, Pravin [Purdue University, School of Nuclear Engineering, 400 Central Dr., West Lafayette, IN 47907-2017 (United States)], E-mail: psawant@purdue.edu; Ishii, Mamoru [Purdue University, School of Nuclear Engineering, 400 Central Dr., West Lafayette, IN 47907-2017 (United States)], E-mail: ishii@purdue.edu; Mori, Michitsugu [Tokyo Electric Power Co. Inc., 4-1 Egasaki-cho, Tsurumi-ku, Yokohama 230-8510 (Japan)], E-mail: michitsugu.mori@tepco.co.jp

    2009-08-15

    Prediction of amount of entrained droplets or entrainment fraction in annular two-phase flow is essential for the estimation of dryout condition and analysis of post dryout heat transfer in light water nuclear reactors and steam boilers. In this study, air-water and organic fluid (Freon-113) annular flow entrainment experiments have been carried out in 9.4 and 10.2 mm diameter test sections, respectively. Both the experiments covered three distinct pressure conditions and wide range of liquid and gas flow conditions. The organic fluid experiments simulated high pressure steam-water annular flow conditions. In each experiment, measurements of entrainment fraction, droplet entrainment rate and droplet deposition rate have been performed by using the liquid film extraction method. A simple, explicit and non-dimensional correlation developed by Sawant [Sawant, P.H., Ishii, M., Mori, M., 2008. Droplet entrainment correlation in vertical upward co-current annular two-phase flow. Nucl. Eng. Des. 238 (6), 1342-1352] for the prediction of entrainment fraction is further improved in this study in order to account for the existence of critical gas and liquid flow rates below which no entrainment is possible. Additionally, a new correlation is proposed for the estimation of minimum liquid film flow rate at the maximum entrainment fraction condition. The improved correlation successfully predicted the newly collected air-water and Freon-113 entrainment fraction data. Furthermore, the correlations satisfactorily compared with the air-water, helium-water and air-genklene experimental data measured by Willetts [Willetts, I.P., 1987. Non-aqueous annular two-phase flow. D.Phil. Thesis, University of Oxford]. However, comparison of the correlations with the steam-water data available in literature showed significant discrepancies. It is proposed that these discrepancies might have been caused due to the inadequacy of the liquid film extraction method used to measure the entrainment

  6. Electronic Switch Arrays for Managing Microbattery Arrays

    Mojarradi, Mohammad; Alahmad, Mahmoud; Sukumar, Vinesh; Zghoul, Fadi; Buck, Kevin; Hess, Herbert; Li, Harry; Cox, David

    2008-01-01

    Integrated circuits have been invented for managing the charging and discharging of such advanced miniature energy-storage devices as planar arrays of microscopic energy-storage elements [typically, microscopic electrochemical cells (microbatteries) or microcapacitors]. The architecture of these circuits enables implementation of the following energy-management options: dynamic configuration of the elements of an array into a series or parallel combination of banks (subarrarys), each array comprising a series of parallel combination of elements; direct addressing of individual banks for charging/or discharging; and, disconnection of defective elements and corresponding reconfiguration of the rest of the array to utilize the remaining functional elements to obtain the desited voltage and current performance. An integrated circuit according to the invention consists partly of a planar array of field-effect transistors that function as switches for routing electric power among the energy-storage elements, the power source, and the load. To connect the energy-storage elements to the power source for charging, a specific subset of switches is closed; to connect the energy-storage elements to the load for discharging, a different specific set of switches is closed. Also included in the integrated circuit is circuitry for monitoring and controlling charging and discharging. The control and monitoring circuitry, the switching transistors, and interconnecting metal lines are laid out on the integrated-circuit chip in a pattern that registers with the array of energy-storage elements. There is a design option to either (1) fabricate the energy-storage elements in the corresponding locations on, and as an integral part of, this integrated circuit; or (2) following a flip-chip approach, fabricate the array of energy-storage elements on a separate integrated-circuit chip and then align and bond the two chips together.

  7. Carbon nanotube nanoelectrode arrays

    Ren, Zhifeng; Lin, Yuehe; Yantasee, Wassana; Liu, Guodong; Lu, Fang; Tu, Yi

    2008-11-18

    The present invention relates to microelectode arrays (MEAs), and more particularly to carbon nanotube nanoelectrode arrays (CNT-NEAs) for chemical and biological sensing, and methods of use. A nanoelectrode array includes a carbon nanotube material comprising an array of substantially linear carbon nanotubes each having a proximal end and a distal end, the proximal end of the carbon nanotubes are attached to a catalyst substrate material so as to form the array with a pre-determined site density, wherein the carbon nanotubes are aligned with respect to one another within the array; an electrically insulating layer on the surface of the carbon nanotube material, whereby the distal end of the carbon nanotubes extend beyond the electrically insulating layer; a second adhesive electrically insulating layer on the surface of the electrically insulating layer, whereby the distal end of the carbon nanotubes extend beyond the second adhesive electrically insulating layer; and a metal wire attached to the catalyst substrate material.

  8. Array Antenna Limitations

    Jonsson, B L G; Hussain, N

    2013-01-01

    This letter defines a physical bound based array figure of merit that provides a tool to compare the performance of both single and multi-band array antennas with respect to return-loss, thickness of the array over the ground-plane, and scan-range. The result is based on a sum-rule result of Rozanov-type for linear polarization. For single-band antennas it extends an existing limit for a given fixed scan-angle to include the whole scan-range of the array, as well as the unit-cell structure in the bound. The letter ends with an investigation of the array figure of merit for some wideband and/or wide-scan antennas with linear polarization. We find arrays with a figure of merit >0.6 that empirically defines high-performance antennas with respect to this measure.

  9. Free and friction-induced in-plane vibration of annular disks

    Tzou, Kevin Ihwa

    1998-12-01

    Vibration and noise from disk brakes negatively affect passenger comfort and perceptions of quality in both the automotive and aircraft industries. With regulatory pressure for stopping distance and the emphasis on smaller and lighter components, new brakes not only have to meet design and performance requirements, but must minimize vibration as well. Although materials and geometries vary from application to application, disk brakes generally consist of rotating annular disk(s) subjected to in-plane friction which dissipates the kinetic energy of the vehicle. During this process, friction-induced vibration of the disk(s) occurs, resulting in brake noise. Although sound radiation results from a disk's out-of-plane vibration, substantial in-plane motions must also be present due to the in-plane friction. This in-plane vibration can play a key role in the dynamics of the friction interface and hence, in brake noise and vibration. In this thesis, experimental and analytical methods are used to study the in-plane vibration of annular disks with a view toward understanding disk brake vibration. The issues that are addressed and the major findings include: (1) Characterization of in-plane modes in annular disks. For automotive rotors and thick annular disks, in-plane modes of vibration have frequencies that are both comparable to low-order bending modes and within the measured range for brake squeal. Despite the large in-plane friction force provided by disk brakes, no existing model includes in-plane disk motion with in-plane friction. A three-dimensional vibration model is used to determine frequencies and mode shapes for an annular disk subject to two boundary conditions: all surfaces traction-free, and all free except for a constrained inner edge. (2) Identification of frequency clusters. Using experimental and analytical methods, the frequencies for families of in-plane modes are found to converge to a common value with increasing disk thickness to the limit of the

  10. Pacific Array (Transportable Broadband Ocean Floor Array)

    Kawakatsu, Hitoshi; Ekstrom, Goran; Evans, Rob; Forsyth, Don; Gaherty, Jim; Kennett, Brian; Montagner, Jean-Paul; Utada, Hisashi

    2016-04-01

    Based on recent developments on broadband ocean bottom seismometry, we propose a next generation large-scale array experiment in the ocean. Recent advances in ocean bottom broadband seismometry1, together with advances in the seismic analysis methodology, have enabled us to resolve the regional 1-D structure of the entire lithosphere/asthenosphere system, including seismic anisotropy (azimuthal, and hopefully radial), with deployments of ~15 broadband ocean bottom seismometers (BBOBSs). Having ~15 BBOBSs as an array unit for a 2-year deployment, and repeating such deployments in a leap-frog way or concurrently (an array of arrays) for a decade or so would enable us to cover a large portion of the Pacific basin. Such efforts, not only by giving regional constraints on the 1-D structure beneath Pacific ocean, but also by sharing waveform data for global scale waveform tomography, would drastically increase our knowledge of how plate tectonics works on this planet, as well as how it worked for the past 150 million years. International collaborations is essential: if three countries/institutions participate this endeavor together, Pacific Array may be accomplished within five-or-so years.

  11. The solution of a wedge disclination dipole interacting with an annular inclusion and the force acting on the disclination dipole

    Song Hao-Peng; Fang Qi-Hong; Liu You-Wen

    2008-01-01

    The interaction between a wedge disclination dipole and an elastic annular inclusion is investigated. Utilizing the Muskhelishvili complex variable method, the explicit series form solutions of the complex potentials in the matrix and the inclusion region are derived. The image force acting on the disclination dipole centre is also calculated. The influence of the location of the disclination dipole and the thickness of the annular inclusion as well as the elastic dissimilarity of materials upon the equilibrium position of the disclination dipole is discussed in detail. The results show that a stable equilibrium point of the disclination dipole near the inclusion is found for certain combinations of material constant.Moreover, the force on the disclination dipole is strongly affected by the position of the disclination dipole and the thickness of annular inclusion. The repulsion force increases (or the attraction force reduces) with the increase of the thickness of the annular inclusion. An appropriate critical value of the thickness of the annular inclusion may be found to change the direction of the force on the disclination dipole. The present solutions include previous results as special cases.

  12. Riboflavin crosslinked high-density collagen gel for the repair of annular defects in intervertebral discs: An in vivo study.

    Grunert, Peter; Borde, Brandon H; Towne, Sara B; Moriguchi, Yu; Hudson, Katherine D; Bonassar, Lawrence J; Härtl, Roger

    2015-10-01

    Open annular defects compromise the ability of the annulus fibrosus to contain nuclear tissue in the disc space, and therefore lead to disc herniation with subsequent degenerative changes to the entire intervertebral disc. This study reports the use of riboflavin crosslinked high-density collagen gel for the repair of annular defects in a needle-punctured rat-tail model. High-density collagen has increased stiffness and greater hydraulic permeability than conventional low-density gels; riboflavin crosslinking further increases these properties. This study found that treating annular defects with crosslinked high-density collagen inhibited the progression of disc degeneration over 18 weeks compared to untreated control discs. Histological sections of FITC-labeled collagen gel revealed an early tight attachment to host annular tissue. The gel was subsequently infiltrated by host fibroblasts which remodeled it into a fibrous cap that bridged the outer disrupted annular fibers and partially repaired the defect. This repair tissue enhanced retention of nucleus pulposus tissue, maintained physiological disc hydration, and preserved hydraulic permeability, according to MRI, histological, and mechanical assessments. Degenerative changes were partially reversed in treated discs, as indicated by an increase in nucleus pulposus size and hydration between weeks 5 and 18. The collagen gel appeared to work as an instant sealant and by enhancing the intrinsic healing capabilities of the host tissue.

  13. The modulation of oceanic moisture transport by the hemispheric annular modes

    Raquel eNieto

    2014-07-01

    Full Text Available Leaving aside the contribution made by recycling, it is the main oceanic moisture sources that are responsible for most of the precipitation that falls on the continents. The transport of moisture from these sources can be affected by large-scale variability according to the hemispheric annular modes. The influence of the two dominant modes of extratropical winter climate: the Northern and the Southern Annular Modes (NAM and SAM are herein investigated to assess how they affect the transport of moisture from the major oceanic moisture sources. A Lagrangian model was used, together with ERA-Interim reanalysis data (1979-2012, and differences between the composites of the six strongest higher and lower events observed for both phases of the two modes for the period were analysed. The method is able to reproduce the general pattern of known variations for both annular patterns. Lower values of the NAM Index are associated with the displacement of the storm track towards tropical latitudes. Thus, moisture transport is enhanced from the Northern Pacific towards the northeastern basin and from the Northern Atlantic and Mediterranean towards southern Europe. On the other hand, during higher values of NAM, moisture transport is favoured from the Northern Pacific towards eastern Asia, and moisture transport is enhanced from the Northern Atlantic towards the Caribbean Sea. In the Southern Hemisphere, during higher values of SAM more moisture is transported from the Atlantic and Indian oceanic sources southwards and eastwards than during the opposite phase. In this SAM phase it is also noted by an enhancement of moisture transport from the Coral Sea and Southern Pacific sources towards the Indian Ocean/West Pacific Warm Pool. Southeastern South America received more moisture from the Pacific and Atlantic sources during years with a lower SAM, episodes which also favoured the influx of moisture from the Southern Atlantic towards Africa, causing monsoon

  14. Microwave generation enhancement of X-band CRBWO by use of coaxial dual annular cathodes

    Yan Teng

    2013-07-01

    Full Text Available This paper presents an approach that greatly enhances both the output power and the conversion efficiency of the coaxial relativistic backward wave oscillator (CRBWO by using coaxial dual annular cathodes, which increases the diode current rather than the diode voltage. The reasons for the maladjustment of CRBWO under a high diode voltage are analyzed theoretically. It is found that by optimization of the diode structure, the shielding effect of the space charge of the outer beams on the inner cathode can be alleviated effectively and dual annular beams with the same kinetic energy can be explosively emitted in parallel. The coaxial reflector can enhance the conversion efficiency by improving the premodulation of the beams. The electron dump on the inner conductor ensures that the electron beams continue to provide kinetic energy to the microwave output until they vanish. Particle-in-cell (PIC simulation results show that generation can be enhanced up to an output power level of 3.63 GW and conversion efficiency of 45% at 8.97 GHz under a diode voltage of 659 kV and current of 12.27 kA. The conversion efficiency remains above 40% and the output frequency variation is less than 100 MHz over a voltage range of more than 150 kV. Also, the application of the coaxial dual annular cathodes means that the diode impedance is matched to that of the transmission line of the accelerators. This impedance matching can effectively eliminate power reflection at the diode, and thus increase the energy efficiency of the entire system.

  15. Properties of disturbance waves in vertical annular two-phase flow

    Sawant, Pravin [Purdue University, School of Nuclear Engineering, 400 Central Dr., West Lafayette, IN 47907-2017 (United States)], E-mail: psawant@purdue.edu; Ishii, Mamoru [Purdue University, School of Nuclear Engineering, 400 Central Dr., West Lafayette, IN 47907-2017 (United States); Hazuku, Tatsuya; Takamasa, Tomoji [Faculty of Marine Technology, Tokyo University of Marine Science and Technology, Etchujima, Koto-ku, Tokyo 135-8533 (Japan); Mori, Michitsugu [Tokyo Electric Power Co., Inc., 4-1 Egasaki-cho, Tsurumi-ku, Yokohama 230-8510 (Japan)

    2008-12-15

    Disturbance waves play an important role in interfacial transfer of mass, momentum and energy in annular two-phase flow. In spite of their importance, majority of the experimental data available in literature on disturbance wave properties such as velocity, frequency, wavelength and amplitude are limited to near atmospheric conditions (Azzopardi, B.J., 1997. Drops in annular two-phase flow. International Journal of Multiphase Flow, 23, 1-53). In view of this, air-water annular flow experiments have been conducted at three pressure conditions (1.2, 4.0 and 5.8 bar) in a tubular test section having an inside diameter 9.4 mm. At each pressure condition liquid and gas phase flow rates are varied over a large range so that the effects of density ratio, liquid flow rate and gas flow rate on disturbance wave properties can be studied systematically. A liquid film thickness is measured by two flush mounted ring shaped conductance probes located 38.1 mm apart. Disturbance wave velocity, frequency, amplitude and wavelength are estimated from the liquid film thickness measurements by following the statistical analysis methods. Parametric trends in variations of disturbance wave properties are analyzed using the non-dimensional numbers; liquid phase Reynolds number (Re{sub f}), gas phase Reynolds number (Re{sub g}), Weber number (We) and Strouhal number (Sr). Finally, the existing correlations available for the prediction of disturbance wave velocity and frequency are analyzed and a new, improved correlation is proposed for the prediction of disturbance wave frequency. The new correlation satisfactorily predicted the current data and the data available in literature.

  16. Integrated avalanche photodiode arrays

    Harmon, Eric S.

    2015-07-07

    The present disclosure includes devices for detecting photons, including avalanche photon detectors, arrays of such detectors, and circuits including such arrays. In some aspects, the detectors and arrays include a virtual beveled edge mesa structure surrounded by resistive material damaged by ion implantation and having side wall profiles that taper inwardly towards the top of the mesa structures, or towards the direction from which the ion implantation occurred. Other aspects are directed to masking and multiple implantation and/or annealing steps. Furthermore, methods for fabricating and using such devices, circuits and arrays are disclosed.

  17. Transmission of sound through annular ducts of varying cross sections and sheared mean flow

    Nayfeh, A. H.; Kaiser, J. E.; Telionis, D. P.

    1974-01-01

    An asymptotic solution is presented for the transmission and attenuation of acoustic waves in an annular duct of slowly varying cross section which carries a sheared mean flow. The analysis also takes into account the growth of the boundary layer as well as any slow variations in the acoustic liner properties. The problem is reduced to the solution of a first-order ordinary differential equation for the amplitude. The analysis is used to estimate the effects of the variations of the duct cross section and boundary layer growth on the different acoustic modes.

  18. Spontaneous fluxon production in annular Josephson tunnel junctions in the presence of a magnetic field

    Monaco, Roberto; Aarøe, Morten; Mygind, Jesper;

    2008-01-01

    We report on the spontaneous production of fluxons in annular Josephson tunnel junctions during a thermal quench in the presence of a symmetry-breaking magnetic field. The dependence on field intensity B of the probability (f) over bar (1) to trap a single defect during the N-S phase transition...... depends drastically on the sample circumferences. We show that this can be understood in the framework of the same picture of spontaneous defect formation that leads to the experimentally well attested scaling behavior of (f) over bar (1) with quench rate in the absence of an external field....

  19. Optimized Annular Triode Ion Pump for Experimental Areas in the LHC

    Knaster, J R; Chatelaine, A; Flakowski, D; Girard, C; Ivaldi, S; Laurent, Jean Michel; Monteiro, I; Rossi, A; Veness, R J M

    2003-01-01

    The LHC will be the world next generation accelerator to be operational in 2007 at CERN. The UHV requirements force the installation of ion pumps in the experimental areas of ATLAS. Due to the unacceptable particle background that standards ion pumps may generate, a reduction in the amount of material constitutive of the pump body is required. Hence, an stainless steel 0.8 mm thick body annular triode ion pump has been designed. A pumping speed of ~ 20 l/s at 10-9 mbar is provided by 15 pumping elements. Finite elements analysis and destructive tests have been performed in its design. Final vacuum tests results are shown.

  20. Experimental study on large diameter drilling in hard rock annular coring

    Yinzhu WU; Guochun YANG; Wenchen WANG

    2008-01-01

    Based on analyzing method of large diameter hard rock drilling at home and abroad, the authors proposed a set of drilling of large diameter hard rock annular coring in low energy consumption, low cost and high efficiency. The prototype of drilling tools was designed and was made. The experimental result of the prototype indicates that this plan and technology are feasible and reach the anticipated object of design. A set of drilling tools has been offered for the constructs of large diameter hard rock coring.

  1. Self-organized Hydrodynamics in an Annular Domain: Modal Analysis and Nonlinear Effects

    Degond, Pierre; Yu, Hui

    2014-01-01

    The Self-Organized Hydrodynamics model of collective behavior is studied on an annular domain. A modal analysis of the linearized model around a perfectly polarized steady-state is conducted. It shows that the model has only pure imaginary modes in countable number and is hence stable. Numerical computations of the low-order modes are provided. The fully non-linear model is numerically solved and nonlinear mode-coupling is then analyzed. Finally, the efficiency of the modal decomposition to a...

  2. Design of the annular binary filters with super-resolution based on the genetic algorithm

    YU Qi-lei; LE Zi-chun; ZHU Hong-ying

    2006-01-01

    To improve the density of information storage,this paper introduces a kind of annular binary filters with super-resolution,Several of these filters have been designed based on the genetic algorithm,the simulations demonstrate that the transverse gain of the filters can reach the value of 1.37.Thus they can remarkably decrease the recording spot size,which is helpful to improve the density of information storage and to make the depth of focus longer,and therefore they can avoid the mistake caused by the small undulation of the optical disk in the process of recording/reading the information.

  3. Granuloma annulare and necrobiosis lipoidica with sequential occurrence in a patient: report and review of literature

    Rupley, Katherine A.; Riahi, Ryan R.; Hooper, Deirdre O’Boyle

    2015-01-01

    Granuloma annulare (GA) and necrobiosis lipoidica (NL) are granulomatous diseases of undetermined etiology. Rarely, both dermatoses have been reported to occur concomitantly in patients. GA and NL are characterized histologically by areas of necrobiosis of collagen. The two diseases share some common characteristics, which may suggest that these dermatoses could occur as a spectrum in some patients or possibly share a similar pathogenesis. We report on a 67-year-old Caucasian woman with a history of NL on the anterior shins that later developed lesions of GA on the breasts, trunk, and wrist. We also review the literature and discuss the characteristics of patients with concomitant GA and NL. PMID:25692078

  4. Magnetostriction measuring device based on an optical fiber sensor with an annular photodiode.

    de Manuel, V; Del Real, R P; Alonso, J; Guerrero, H

    2007-09-01

    A new simple and sensitive dilatometer to measure magnetostriction of ribbons has been developed, based on an optical fiber sensor using an annular photodiode. The optical fiber is used bidirectionally, both for emission and detection of light, simplifying the access to the ribbon under test. The working principle is based on the measurement by reflection of the longitudinal displacement of the ribbon end. For a Vitroperm amorphous ribbon of 100 mm length, 21 microm thickness, and 8.3 mm width, a displacement of 2.571 microm with a maximum uncertainty of 8 nm has been obtained.

  5. Experimental investigation on Heat Transfer Performance of Annular Flow Path Heat Pipe

    Kim, In Guk; Kim, Kyung Mo; Jeong, Yeong Shin; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of)

    2015-05-15

    Mochizuki et al. was suggested the passive cooling system to spent nuclear fuel pool. Detail analysis of various heat pipe design cases was studied to determine the heat pipes cooling performance. Wang et al. suggested the concept PRHRS of MSR using sodium heat pipes, and the transient performance of high temperature sodium heat pipe was numerically simulated in the case of MSR accident. The meltdown at the Fukushima Daiichi nuclear power plants alarmed to the dangers of station blackout (SBO) accident. After the SBO accident, passive decay heat removal systems have been investigated to prevent the severe accidents. Mochizuki et al. suggested the heat pipes cooling system using loop heat pipes for decay heat removal cooling and analysis of heat pipe thermal resistance for boiling water reactor (BWR). The decay heat removal systems for pressurized water reactor (PWR) were suggested using natural convection mechanisms and modification of PWR design. Our group suggested the concept of a hybrid heat pipe with control rod as Passive IN-core Cooling System (PINCs) for decay heat removal for advanced nuclear power plant. Hybrid heat pipe is the combination of the heat pipe and control rod. In the present research, the main objective is to investigate the effect of the inner structure to the heat transfer performance of heat pipe containing neutron absorber material, B{sub 4}C. The main objective is to investigate the effect of the inner structure in heat pipe to the heat transfer performance with annular flow path. ABS pellet was used instead of B{sub 4}C pellet as cylindrical structures. The thermal performances of each heat pipes were measured experimentally. Among them, concentric heat pipe showed the best performance compared with others. 1. Annular evaporation section heat pipe and annular flow path heat pipe showed heat transfer degradation. 2. AHP also had annular vapor space and contact cooling surface per unit volume of vapor was increased. Heat transfer

  6. Digital controller design: Analysis of the annular suspension pointing system. [analog controllers with feedback

    Kuo, B. C.

    1978-01-01

    The analog controllers of the annular suspension pointing system are designed for control of the chi, phi sub 1, and phi sub 2 bandwidth dynamics through decoupling and pole placement. Since it is virtually impossible to find an equivalent bandwidth of the overall system and establish a general eigenvalue requirement for the system, the subsystem dynamics are decoupled through state feedback and the poles are placed simultaneously to realize the desired bandwidths for the three system components. Decoupling and pole placement are also used to design the closed-loop digital system through approximation.

  7. Study on Friction Factor of Developing and Developed Laminar FLow in Annular-Sector Ducts

    1995-01-01

    The pressure drops of laminar developing and developed flow in annular-sector ducts with small roud corner have been investigated experimentally.Numerical simulation has been performed to study the effect of the small round corner on the friction factor in the developed region.It has been found that with the increase in corner radius,the value of f Re decreases,In the range of rc/ro from 0.031to 0.12,the decrease in fRe varies from 0.048%to 0.1% for the fie apex angle computed.

  8. Recent advances of annular centrifugal extractor for hot test of nuclear waste partitioning process

    HeXiang-Ming; YanYu-Shun; 等

    1998-01-01

    Advances are being made in the design of the annular centrifugal extractor fornuclear fuel reprocessing extraction process studies.The extractors have been built and tested.Twelve stages of this extractor and 50 stages are used toimplement the TRPO process for the cleanup ofcommercial and defense nuclear waste liquids,respectively.Following advances are available:(1) simple way of assembly and disassembly between rotor part and housing part of extractor,ease of manipulator operation;(2)automatic sampling from housing of extractor in hot cell;(3) compact multi-stage housing system;(4) easy interstage link;(5) computer data acquisition and monitoring system of speed.

  9. Stability analysis of thermo-acoustic nonlinear eigenproblems in annular combustors. Part II. Uncertainty quantification

    Magri, Luca; Nicoud, Franck; Juniper, Matthew

    2016-01-01

    Monte Carlo and Active Subspace Identification methods are combined with first- and second-order adjoint sensitivities to perform (forward) uncertainty quantification analysis of the thermo-acoustic stability of two annular combustor configurations. This method is applied to evaluate the risk factor, i.e., the probability for the system to be unstable. It is shown that the adjoint approach reduces the number of nonlinear-eigenproblem calculations by up to $\\sim\\mathcal{O}(M)$, as many as the Monte Carlo samples.

  10. Description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory test model

    Woolley, C. T.; Groom, N. J.

    1981-01-01

    A description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory model is presented. The AMCD is a momentum exchange device which is under development as an advanced control effector for spacecraft attitude control systems. The digital computer simulation of this device incorporates the following models: six degree of freedom rigid body dynamics; rim warp; controller dynamics; nonlinear distributed element axial bearings; as well as power driver and power supply current limits. An annotated FORTRAN IV source code listing of the computer program is included.

  11. Numerical Study of an Annular Gas Turbine Combustor with Dump Diffuser

    J.X.Zhao; Y.B.Lai

    1999-01-01

    A general numerical method is presented for calculating steady three-dimensional and two-phase turbulent reactive flows with a nonstaggered body-fitted coordinate system in an annular gas turbine combustor with the dump diffuser.The modified two-equation model and the EDC turbulent combustion model are used for the gas phase.The liquid phase equations are solved in a Lagrangian frame of reference by PSIC algorithm.The effect of different velocity profiles at the entry of the prediffuser on combustor flow characteristics is calculated.

  12. Focal plane array with modular pixel array components for scalability

    Kay, Randolph R; Campbell, David V; Shinde, Subhash L; Rienstra, Jeffrey L; Serkland, Darwin K; Holmes, Michael L

    2014-12-09

    A modular, scalable focal plane array is provided as an array of integrated circuit dice, wherein each die includes a given amount of modular pixel array circuitry. The array of dice effectively multiplies the amount of modular pixel array circuitry to produce a larger pixel array without increasing die size. Desired pixel pitch across the enlarged pixel array is preserved by forming die stacks with each pixel array circuitry die stacked on a separate die that contains the corresponding signal processing circuitry. Techniques for die stack interconnections and die stack placement are implemented to ensure that the desired pixel pitch is preserved across the enlarged pixel array.

  13. Analysis of VCSEL Array Module Using a Simple Microlens Array

    Hen-Wai; Tsao; Shyh-Lin; Tsao

    2003-01-01

    A simple microlens array is designed between VCSEL array and fiber array for integration of array module. We increase the optical coupling efficiency from -32.057 dBm to -0.9054 dBm by using our designed microlens array.

  14. Analysis of VCSEL Array Module Using a Simple Microlens Array

    Wen-Ming Cheng; Hen-Wai Tsao; Shyh-Lin Tsao

    2003-01-01

    A simple microlens array is designed between VCSEL array and fiber array for integration of array module. We increase the optical coupling efficiency from-32.057 dBm to-0.9054 dBm by using our designed microlens array.

  15. Impact of 15 Jan 2010 annular solar eclipse on the equatorial and low latitude ionosphere over Indian region from Magnetometer, Ionosonde and GPS observations

    Panda, Sampad Kumar; Rajaram, Girija; Sripathi, Samireddipalle; Bhaskar, Ankush

    2015-01-01

    The annular eclipse of Jan 15, 2010 over southern India was studied with a network of multi-instrumental observations consisting magnetometer, ionosonde and GPS receivers. By selecting the day before and the normal EEJ days as the control days, it is intrinsically proved that the regular eastward electric field for the whole day at the equator was not just weakened but actually was flipped for several hours by the influence of tides related to the spectacular Sun-Moon-Earth alignment near the middle of the day. The effect of flipping the electric field was clearly seen in the equatorial ionosonde data and through the large array of GPS receivers that accomplished the TEC data. The main impact of the change in the electric field was the reduced EIA at all latitudes, with the anomaly crest that shifted towards the equator. The equatorial F-region density profile was also showing an enhanced F region peak in spite of a reduced VTEC. By comparison to the plasma density depletion associated with the temporary lack...

  16. Numerical Analysis of General Trends in Single-Phase Natural Circulation in a 2D-Annular Loop

    Gilles Desrayaud

    2008-01-01

    Full Text Available The aim of this paper is to address fluid flow behavior of natural circulation in a 2D-annular loop filled with water. A two-dimensional, numerical analysis of natural convection in a 2D-annular closed-loop thermosyphon has been performed for various radius ratios from 1.2 to 2.0, the loop being heated at a constant flux over the bottom half and cooled at a constant temperature over the top half. It has been numerically shown that natural convection in a 2D-annular closed-loop thermosyphon is capable of showing pseudoconductive regime at pitchfork bifurcation, stationary convective regimes without and with recirculating regions occurring at the entrance of the exchangers, oscillatory convection at Hopf bifurcation and Lorenz-like chaotic flow. The complexity of the dynamic properties experimentally encountered in toroidal or rectangular loops is thus also found here.

  17. Is Mitral Annular Calcification Associated With Atherosclerotic Risk Factors and Severity and Complexity of Coronary Artery Disease?

    Bhatt, Hemal; Sanghani, Dharmesh; Julliard, Kell; Fernaine, George

    2015-08-01

    We assessed the association of mitral annular calcification (MAC) with atherosclerotic risk factors and severity and complexity of coronary artery disease (CAD). Cardiac catheterization reports and electronic medical records from 2010 to 2011 were retrospectively reviewed. A total of 481 patients were divided into 2 groups: MAC present (209) and MAC absent (272). All major cardiovascular risk factors, comorbidities, and coronary lesion characteristics were included. On linear regression analysis, age (P = .001, β 1.12) and female gender (P = .031, β 0.50) were the independent predictors of MAC. Mitral annular calcification was not independently associated with the presence of lesions with >70% stenosis (P = .283), number of obstructive vessels (P = .469), lesions with 50% to 70% stenosis (P = .458), and Synergy Between Percutaneous Coronary Intervention With Taxus and Cardiac Surgery score (P = .479). Mitral annular calcification is probably a benign marker of age-related degenerative changes in the heart independent of the severity and complexity of CAD.

  18. DETERMINATION OF CRITICAL ROTATIONAL SPEED OF CIRCULAR SAWS FROM NATURAL FREQUENCIES OF ANNULAR PLATE WITH ANALOGOUS DIMENSIONS

    Ante Skoblar

    2016-03-01

    Full Text Available It is suitable to reduce thickness of circular saw when trying to enhance usability of wood raw material, but reducing thickness also causes reduction of permissible rotational speed which reduces sawing speed. If one increase circular saw rotational speed over permissible one the quality of machined surfaces will reduce because of enhanced vibrations. Permissible rotational speed can be calculated from critical rotational speed which can be defined from natural frequencies of the saw. In this article critical rotational speeds of standard clamped saws (with flat disk surface and without slots are calculated by using finite element method and classical theory of thin plates on annular plates. Mode shapes and natural frequencies of annular plates are determined by using Bessel functions and by using polynomial functions. Obtained results suggest that standard clamped circular saws without slots and with relatively small teeth can be determined from classical theory of thin plates for annular plates with accuracy depending on clamping ratio.

  19. The Hydraulic Test Report for Non-instrumented Irradiation Test Rig of DUO-Cooled Annular Pellet

    Kim, Dae Ho; Lee, Kang Hee; Shin, Chang Hwan; Yang, Yong Sik; Kim, Sun Ki; Bang, Je Geon; Song, Kun Woo

    2007-08-15

    This report presents the results of pressure drop test and vibration test for non-instrumented rig of Advanced PWR DUO-Fuel Annular Pellet which were designed and fabricated by KAERI. From the pressure drop test results, it is noted that the flow velocity across the non-instrumented rig of Advanced PWR DUO-Fuel Annular Pellet corresponding to the pressure drop of 200 kPa is measured to be about 8.30 kg/sec. Vibration frequency results for the non-instrumented rig at the pump spin frequency ranges from 19.0 to 32.0 Hz, RMS(Root Mean Square) displacement for the non-instrumented rig of Advanced PWR DUO-Fuel Annular Pellet is less than 7.25 m, and the maximum displacement is less than 31.27 {mu}m. This test was performed at the FIVPET facility.

  20. Review:Liquid film dryout model for predicting critical heat flux in annular two-phase flow

    Bo JIAO; Li-min QIU; Jun-liang LU; Zhi-hua GAN

    2009-01-01

    Gas-liquid two-phase flow and heat transfer can be encountered in numerous fields, such as chemical engineering, refrigeration, nuclear power reactor, metallurgical industry, spaceflight. Its critical heat flux (CHF) is one of the most important factors for the system security of engineering applications. Since annular flow is the most common flow pattern in gas-liquid two-phase flow, predicting CHF of annular two-phase flow is more significant. Many studies have shown that the liquid film dryout model is successful for that prediction, and determining the following parameters will exert predominant effects on the accuracy of this model: onset of annular flow, inception criterion for droplets entrainment, entrainment fraction, droplets deposi-tion and entrainment rates. The main theoretical results achieved on the above five parameters are reviewed; also, limitations in the existing studies and problems for further research are discussed.

  1. Solar array deployment mechanism

    Calassa, Mark C.; Kackley, Russell

    1995-05-01

    This paper describes a Solar Array Deployment Mechanism (SADM) used to deploy a rigid solar array panel on a commercial spacecraft. The application required a deployment mechanism design that was not only lightweight, but also could be produced and installed at the lowest possible cost. This paper covers design, test, and analysis of a mechanism that meets these requirements.

  2. Array for detecting microbes

    Andersen, Gary L.; DeSantis, Todd D.

    2014-07-08

    The present embodiments relate to an array system for detecting and identifying biomolecules and organisms. More specifically, the present embodiments relate to an array system comprising a microarray configured to simultaneously detect a plurality of organisms in a sample at a high confidence level.

  3. Photovoltaic array loss mechanisms

    Gonzalez, Charles

    1986-10-01

    Loss mechanisms which come into play when solar cell modules are mounted in arrays are identified. Losses can occur either from a reduction in the array electrical performance or with nonoptimal extraction of power from the array. Electrical performance degradation is caused by electrical mismatch, transmission losses from cell surface soiling and steep angle of reflectance, and electrical losses from field wiring resistance and the voltage drop across blocking diodes. The second type of loss, concerned with the operating points of the array, can involve nonoptimal load impedance and limiting the operating envelope of the array to specific ranges of voltage and current. Each of the loss mechanisms are discussed and average energy losses expected from soiling, steep reflectance angles and circuit losses are calculated.

  4. Microfabricated ion trap array

    Blain, Matthew G.; Fleming, James G.

    2006-12-26

    A microfabricated ion trap array, comprising a plurality of ion traps having an inner radius of order one micron, can be fabricated using surface micromachining techniques and materials known to the integrated circuits manufacturing and microelectromechanical systems industries. Micromachining methods enable batch fabrication, reduced manufacturing costs, dimensional and positional precision, and monolithic integration of massive arrays of ion traps with microscale ion generation and detection devices. Massive arraying enables the microscale ion traps to retain the resolution, sensitivity, and mass range advantages necessary for high chemical selectivity. The reduced electrode voltage enables integration of the microfabricated ion trap array with on-chip circuit-based rf operation and detection electronics (i.e., cell phone electronics). Therefore, the full performance advantages of the microfabricated ion trap array can be realized in truly field portable, handheld microanalysis systems.

  5. Annular pancreas

    ... chap 330. Semrin MG, Russo MA. Anatomy, histology, embryology, and developmental anomalies of the stomach and duodenum. ... M. is also a founding member of Hi-Ethics and subscribes to the principles of the Health ...

  6. Mitral annular calcification and aortic valve calcification may help in predicting significant coronary artery disease.

    Acartürk, Esmeray; Bozkurt, Abdi; Cayli, Murat; Demir, Mesut

    2003-01-01

    Mitral annular calcification (MAC) and aortic valve calcification (AVC) are manifestations of atherosclerosis. To determine whether mitral annular calcification and aortic valve calcification detected by transthoracic echocardiography (TTE) might help in predicting significant coronary artery disease (CAD), 123 patients with significant CAD and 93 patients without CAD detected by coronary angiography were investigated. MAC and AVC identified CAD with a sensitivity and specificity of 60.2%, 55.9% and 74.8%, 52.7%, respectively, and with a negative and a positive predictive values of 51.5%, 64.3% and 61.3% and 67.6%, respectively. The positive predictive value of MAC was greater than gender, hypertension, and hypercholesterolemia. AVC showed a positive predictive value greater than gender, hypertension, family history, and hypercholesterolemia. The negative predictive values of MAC and AVC for CAD were greater than those of all risk factors except diabetes mellitus. In conclusion, presence of MAC and AVC on TTE may help in predicting CAD and should be added to conventional risk factors. Absence of MVC and AVC is a stronger predictor for absence of CAD than all conventional risk factors, except diabetes mellitus. Patients with MAC and AVC should be taken into consideration for the presence of significant CAD and thereby for diagnostic and therapeutic interventions in order to improve the prognosis.

  7. Linear stability analysis of axisymmetric flow over a sudden expansion in an annular pipe

    Beladi, Behnaz; Kuhlmann, Hendrik Christoph

    2016-11-01

    A global temporal linear stability analysis is performed of the fully-developed axisymmetric incompressible Newtonian flow in an annular pipe with a sudden radially-inward expansion. The geometry is characterized by the radial expansion ratio (radial step height to the outlet gap width) and the outlet radius ratio (inner-to-outer radius). Stability boundaries have been calculated with finite volumes for an outlet radius ratio of 0 . 1 and expansion ratios from 0 . 25 to 0 . 75 . For expansion ratios less than 0 . 55 the most dangerous mode has an azimuthal wave number m = 3 , whereas m = 2 for larger expansion ratios. An a posteriori analysis of the kinetic energy transferred between the basic state and the critical mode allows to check the energy conservation and to identify the physical instability mechanism. For all expansion ratios considered the basic flow arises as an annular jet between two separation zones which are located immediately after the step. The jet gradually widens downstream before reattaching to the cylinders. The deceleration of the flow associated with the widening of the jet is found to be the primary source of energy for the critical modes.

  8. Propagation of partially coherent annular beams with decentered field in turbulence along a slant path.

    Dou, Lingyu; Ji, Xiaoling; Li, Peiyun

    2012-04-09

    The model of partially coherent annular beams with linear non-uniformity field profile in the x direction is set up. The analytic expressions for the average intensity and the centre of gravity of partially coherent annular beams with decentered field propagating through atmospheric turbulence along a slant path are derived. The propagation equation governing the position of the intensity maximum is also given. It is found that the beam non-uniformity is amended gradually as the propagation distance and the strength of turbulence increase. The centre of beam gravity is independent of both the propagation distance and the turbulence. However, the position of the intensity maximum changes versus the propagation distance and the turbulence, and is farthest away from the propagation z-axis at a certain propagation distance. When the propagation distance is large enough, the position of the intensity maximum reaches an asymptotic value which increases with decreasing the zenith angle and is largest for the free space case. When the propagation distance is large enough, the position of the intensity maximum is not on the propagation z-axis, and is nearer to the propagation z-axis than the centre of beam gravity. On the other hand, changes in the intensity maximum in the far field are also examined in this paper.

  9. Experimental quantification of annular dark-field images in scanning transmission electron microscopy.

    Lebeau, James M; Stemmer, Susanne

    2008-11-01

    This paper reports on a method to obtain atomic resolution Z-contrast (high-angle annular dark-field) images with intensities normalized to the incident beam. The procedure bypasses the built-in signal processing hardware of the microscope to obtain the large dynamic range necessary for consecutive measurements of the incident beam and the intensities in the Z-contrast image. The method is also used to characterize the response of the annular dark-field detector output, including conditions that avoid saturation and result in a linear relationship between the electron flux reaching the detector and its output. We also characterize the uniformity of the detector response across its entire area and determine its size and shape, which are needed as input for image simulations. We present normalized intensity images of a SrTiO(3) single crystal as a function of thickness. Averaged, normalized atom column intensities and the background intensity are extracted from these images. The results from the approach developed here can be used for direct, quantitative comparisons with image simulations without any need for scaling.

  10. Can Eddy Forcing be Responsible for the Spatial Structure of the Northern Hemisphere Annular Mode?

    ZHAO Nan; LI Yan; SHEN Xinyong

    2010-01-01

    In order to study the origin of the spatial structure of the Northern Hemisphere Annular Mode (NAM),a linear stochastic model is constructed empirically from the output of a GCM run.Optimal stochastic forcing in terms of the maximum variance contribution,which may be potentially related to the maintenance of the NAM,is investigated.Theoretical analysis on the dominant non-modal response to the stochastic forcing shows that this dominance is jointly decided by the properties of forcing and the non-modal growth (decay).The results of computation demonstrate that the eddy forcing corresponding to the instantaneous rapid growth of the NAM,which is indicated by the instantaneous stochastic optimum,has a roughly similar but significantly different annular structure like that of the NAM.On the other hand,the eddy forcing corresponding to the stationary variance of the NAM,which is indicated by the asymptotic stochastic optimum,has a totally different structure from that of the NAM.These results,together with our general discussion on the relationship between the spatial structure of forcing and response,suggest that one should be careful when explaining the spatial structure of the NAM by that of the eddy forcing.

  11. Specific features of a rare form of disseminated necrobiosis lipoidica granuloma annulare type: a case report.

    Ianoşi, Simona Laura; Tutunaru, Cristina; Georgescu, Claudia Valentina; Ianoşi, Nicolae Gabriel; Georgescu, Diana Monica; Dănoiu, Suzana; Niculescu, Elena Carmen; Neagoe, Carmen Daniela

    2014-01-01

    Necrobiosis lipoidica (NL) is a rare dermatosis that has been shown to precede the onset of diabetes mellitus in 15% of patients. It is more common in women; the average age of the onset is 30 years. Skin lesions of classic NL begin as a small papule, typically on the bilateral pretibial area. Progressively, these papules become indurated plaques with an atrophic, yellow center and multiple telangiectatic vessels, and brown-violaceous borders. We present the case of a 57-year-old male with type II diabetes mellitus from 2004, class II obesity, hepatosteatosis and metabolic disturbances who presents a disseminated eruption from 2010, formed by indurated plaques with flattened centers and a tendency of atrophy and raised, sharply demarcated, red-violaceous borders, having a variable diameter between 1.5 and 5 cm. The laboratory findings revealed elevated glucose levels between 250 and 300 mg%, high levels of transaminases and lipids. Diagnosis of disseminated necrobiosis lipoidica granuloma annulare-type was histopathologically confirmed. For the treatment, we have used topical corticosteroids and Tacrolimus 0.1% and systemic vasodilators. We consider this rare case interesting because has some peculiarities, as: disseminated lesions extend over the characteristic areas for necrobiosis lipoidica, the characteristic features of lesions similar to granuloma annulare, gender (male) and the onset of the disease over fifth decade.

  12. Internal (Annular) and Compressible External (Flat Plate) Turbulent Flow Heat Transfer Correlations.

    Dechant, Lawrence [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Smith, Justin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-01-01

    Here we provide a discussion regarding the applicability of a family of traditional heat transfer correlation based models for several (unit level) heat transfer problems associated with flight heat transfer estimates and internal flow heat transfer associated with an experimental simulation design (Dobranich 2014). Variability between semi-empirical free-flight models suggests relative differences for heat transfer coefficients on the order of 10%, while the internal annular flow behavior is larger with differences on the order of 20%. We emphasize that these expressions are strictly valid only for the geometries they have been derived for e.g. the fully developed annular flow or simple external flow problems. Though, the application of flat plate skin friction estimate to cylindrical bodies is a traditional procedure to estimate skin friction and heat transfer, an over-prediction bias is often observed using these approximations for missile type bodies. As a correction for this over-estimate trend, we discuss a simple scaling reduction factor for flat plate turbulent skin friction and heat transfer solutions (correlations) applied to blunt bodies of revolution at zero angle of attack. The method estimates the ratio between axisymmetric and 2-d stagnation point heat transfer skin friction and Stanton number solution expressions for sub-turbulent Reynolds numbers %3C1x10 4 . This factor is assumed to also directly influence the flat plate results applied to the cylindrical portion of the flow and the flat plate correlations are modified by

  13. 3-D vibration analysis of annular sector plates using the Chebyshev-Ritz method

    Zhou, D.; Lo, S. H.; Cheung, Y. K.

    2009-02-01

    The three-dimensional free vibration of annular sector plates with various boundary conditions is studied by means of the Chebyshev-Ritz method. The analysis is based on the three-dimensional small strain linear elasticity theory. The product of Chebyshev polynomials satisfying the necessary boundary conditions is selected as admissible functions in such a way that the governing eigenvalue equation can be conveniently derived through an optimization process by the Ritz method. The boundary functions guarantee the satisfaction of the geometric boundary conditions of the plates and the Chebyshev polynomials provide the robustness for numerical calculation. The present study provides a full vibration spectrum for the thick annular sector plates, which cannot be given by the two-dimensional (2-D) theories such as the Mindlin theory. Comprehensive numerical results with high accuracy are systematically produced, which can be used as benchmark to evaluate other numerical methods. The effect of radius ratio, thickness ratio and sector angle on natural frequencies of the plates with a sector angle from 120° to 360° is discussed in detail. The three-dimensional vibration solutions for plates with a re-entrant sector angle (larger than 180°) and shallow helicoidal shells (sector angle larger than 360°) with a small helix angle are presented for the first time.

  14. 3-D NUMERICAL STUDY AND COMPARISON OF ECCENTRIC AND CONCENTRIC ANNULAR-FINNED TUBE HEAT EXCHANGERS

    FAROUK TAHROUR

    2015-11-01

    Full Text Available The use of 3-D computational fluid dynamics (CFD is proposed to simulate the conjugate conduction-convection of heat transfer problems in eccentric annularfinned tube heat exchangers. The numerical simulation results allow us to evaluate the heat transfer coefficient over fin surfaces, the fin efficiency and the pressure drop. The aim of the present paper is to determine the optimum tube position in the circular fin that maximizes heat dissipation and minimizes pressure drop. In addition, this study analyzes the effects of fin spacing and fin tube diameter on heat transfer and flow characteristics for a range of Reynolds numbers, 4500≤Re≤22500. A satisfactory qualitative and quantitative agreement was obtained between the numerical predictions and the results published in the literature. For small fin spacings, the eccentric annular finned tube is more efficient than the concentric one. Among the cases examined, the average heat transfer coefficient of the eccentric annular-finned tube, for a tube shift St =12 mm and a Reynolds number Re = 9923, was 7.61% greater than that of the concentric one. This gain is associated with a 43.09% reduction in pressure drop.

  15. High quantum efficiency annular backside silicon photodiodes for reflectance pulse oximetry in wearable wireless body sensors

    Duun, Sune; Haahr, Rasmus G.; Hansen, Ole; Birkelund, Karen; Thomsen, Erik V.

    2010-07-01

    The development of annular photodiodes for use in a reflectance pulse oximetry sensor is presented. Wearable and wireless body sensor systems for long-term monitoring require sensors that minimize power consumption. We have fabricated large area 2D ring-shaped silicon photodiodes optimized for minimizing the optical power needed in reflectance pulse oximetry. To simplify packaging, backside photodiodes are made which are compatible with assembly using surface mounting technology without pre-packaging. Quantum efficiencies up to 95% and area-specific noise equivalent powers down to 30 fW Hz-1/2 cm-1 are achieved. The photodiodes are incorporated into a wireless pulse oximetry sensor system embedded in an adhesive patch presented elsewhere as 'The Electronic Patch'. The annular photodiodes are fabricated using two masked diffusions of first boron and subsequently phosphor. The surface is passivated with a layer of silicon nitride also serving as an optical filter. As the final process, after metallization, a hole in the center of the photodiode is etched using deep reactive ion etch.

  16. Effect of Spray Cone Angle on Flame Stability in an Annular Gas Turbine Combustor

    Mishra, R. K.; Kumar, S. Kishore; Chandel, Sunil

    2016-04-01

    Effect of fuel spray cone angle in an aerogas turbine combustor has been studied using computational fluid dynamics (CFD) and full-scale combustor testing. For CFD analysis, a 22.5° sector of an annular combustor is modeled and the governing equations are solved using the eddy dissipation combustion model in ANSYS CFX computational package. The analysis has been carried out at 125 kPa and 303 K inlet conditions for spray cone angles from 60° to 140°. The lean blowout limits are established by studying the behavior of combustion zone during transient engine operation from an initial steady-state condition. The computational study has been followed by testing the practical full-scale annular combustor in an aerothermal test facility. The experimental result is in a good agreement with the computational predictions. The lean blowout fuel-air ratio increases as the spray cone angle is decreased at constant operating pressure and temperature. At higher spray cone angle, the flame and high-temperature zone moves upstream close to atomizer face and a uniform flame is sustained over a wide region causing better flame stability.

  17. THE TESTING OF COMMERCIALLY AVAILABLE ENGINEERING AND PLANT SCALE ANNULAR CENTRIFUGAL CONTACTORS FOR THE PROCESSING OF SPENT NUCLEAR FUEL

    Jack D. Law; David Meikrantz; Troy Garn; Nick Mann; Scott Herbst

    2006-10-01

    Annular centrifugal contactors are being evaluated for process scale solvent extraction operations in support of United State Advanced Fuel Cycle Initiative goals. These contactors have the potential for high stage efficiency if properly employed and optimized for the application. Commercially available centrifugal contactors are being tested at the Idaho National Laboratory to support this program. Hydraulic performance and mass transfer efficiency have been measured for portions of an advanced nuclear fuel cycle using 5-cm diameter annular centrifugal contactors. Advanced features, including low mix sleeves and clean-in-place rotors, have also been evaluated in 5-cm and 12.5-cm contactors.

  18. 嗜酸性环形红斑1例%Eosinophilic annular erythema:a case report

    赵晶; 赵天恩; 卢宪梅

    2015-01-01

    A 37-year-old female presented with recurrent annular cutaneous eruption with a slight itching on the trunk for more than one year. Physical examination showed that the red annular infiltrated erythemas varied in different size with light colored centre and raised border. Histopathological examination showed the infiltration of eosinophils in the dermis and subcutaneous fat, but without flame figures or granulomatous in-flammation.%作者单位:1山东省皮肤病性病防治研究所,济南,250022

  19. The Design and Manufacturing Report of Non-Instrumented Rig for Dual-cooled Annular Fuel Irradiation Test in HANARO

    Kim, Dae Ho; Bang, Je Geon; Lim, Ik Sung; Kim, Sun Ki; Yang, Yong Sik; Song, Kun Woo; Seo, Chul Gyo; Park, Chan Kook

    2008-09-15

    This project is preparing to irradiation test of the developed double cooled annular fuel pellet in HANARO for pursuit advanced performance in High Performance Fuel Technology Development as a part Nuclear Mid and Long-term R and D Program. On the basis test rod is performed the nuclei property and preliminary fuel performance analysis, test rod and non-instrumented rig designed and manufactured for irradiation test in HANARO OR hole. This non- instrumented rig was confirmed the compatibility of HANARO and the integrity of rig structure, and satisfied the quality assurance requirements. This non- instrumented rig is adopt to the irradiation test for double cooled annular fuel pellet in HANARO.

  20. Non-Newtonian fluid flow in annular pipes and entropy generation: Temperature-dependent viscosity

    M Yürüsoy; B S Yilbaş; M Pakdemirli

    2006-12-01

    Non-Newtonian fluid flow in annular pipes is considered and the entropy generation due to fluid friction and heat transfer in them is formulated. A third-grade fluid is employed to account for the non-Newtonian effect, while the Reynolds model is accommodated for temperature-dependent viscosity. Closed-form solutions for velocity, temperature, and entropy fields are presented. It is found that entropy generation number increases with reducing non-Newtonian parameter, while it is the reverse for the viscosity parameter, which is more pronounced in the region close to the annular pipe inner wall.

  1. Research on taper zone coupling from single-core fiber to annular-core hollow beam fiber

    Tong, Chengguo; Zhang, Tao; Li, Jianqi; Wang, Pengfei; Kang, Chong; Yuan, Libo

    2016-11-01

    We designed and manufactured a novel annular-core hollow beam fiber which could directly yield ring light with a central dark spot inside the beam employing MCVD technique and a custom-made fiber drawing tower. The tapered fiber zone geometric shapes at varied stretching speed between the single-core fiber and the annular-core hollow beam fiber were studied theoretically. According to the beam propagation method, the bi-tapered coupling energy transmission between these two fibers was simulated and analyzed. Moreover, by adopting a fusion splicing and stretching technique at the fiber-linked point, an effective coupling approach had been fulfilled.

  2. Sapien XT Transcatheter Mitral Valve Replacement Under Direct Vision in the Setting of Significant Mitral Annular Calcification.

    Murashita, Takashi; Suri, Rakesh M; Daly, Richard C

    2016-03-01

    Mitral valve replacement carries a high risk in patients with extensive mitral annular calcification. We report the case of a 71-year-old woman with severely calcified mitral valve stenosis and extensive annular calcification. We approached the mitral valve through a left atriotomy using cardiopulmonary bypass and cardiac arrest. We successfully deployed a 29-mm Sapien XT valve under direct visualization with satisfactory positioning. We further balloon-expanded the device to diminish the likelihood of periprosthetic regurgitation. Open mitral valve replacement with a transcatheter valve can be performed without the need for decalcification of the mitral annulus and is a good alternative to conventional mitral valve replacement.

  3. The Viable Mitral Annular Dynamics and Left Ventricular Function after Mitral Valve Repair by Biological Rings

    Farideh Roshanali

    2012-12-01

    Full Text Available Objective: Considering the importance of annular dynamics in the valvular and ventricular function, we sought to evaluate the effects of treated pericardial annuloplasty rings on mitral annular dynamics and left-ventricular (LV function after mitral valve repair. The results were compared with the mitral annular dynamics and LV function in patients with rigid and flexible rings and also in those without any heart problems. Materials and Methods: One hundred and thirty-six consecutive patients with a myxomatous mitral valve and severe regurgitation were prospectively enrolled in this observational cohort study. The patients underwent comparable surgical mitral valve reconstruction; of these 100 received autologous pericardium rings (Group I, 20 were given flexible prosthetic rings (Group II, and 16 received rigid rings (Group III. Other repair modalities were also performed, depending on the involved segments. The patients were compared with 100 normal subjects in whom an evaluation of the coronary artery was not indicative of valvular or myocardial abnormalities (Group IV. At follow-up, LV systolic indices were assessed via two-dimensional echocardiography at rest and during dobutamine stress echocardiography. Mitral annular motion was examined through mitral annulus systolic excursion (MASE. Peak transmitral flow velocities (TMFV and mitral valve area (MVA were also evaluated by means of continuous-wave Doppler. Results: A postoperative echocardiographic study showed significant mitral regurgitation (>=2+ in one patient in Group I, one patient in Group II, and none in Group III. None of the patients died. There was a noteworthy increase in TMFV with stress in all the groups, the increase being more considerable in the prosthetic ring groups (Group I from 1.10 ± 0.08 to 1.36 ± 0.13 m/s, Group II from 1.30 ± 0.11 to 1.59 ± 0.19 m/s, Group III from 1.33 ± 0.09 to 1.69 ± 0.21 m/s, and Group IV from 1.08 ± 0.08 to 1.21 ± 0.12 m

  4. A Communications Link for an Implantable Electrode Array.

    1984-12-01

    51p.p 1 Frequency 5 V Sine wave centered on 0CV - - - - 40 - MHz J i P~ IPL IT,,"’( Ivoo -v 5 5 -is V ( Switch on) RL ,12 - - ’ -50dB Feed lt::1 1... Protheses ," Ann. Roy. Coll. Surgeons, 47: 106-108 (1970). 8. Hubel, D. H. and Weisel, T. N. "Receptive Fields, Binocular Interaction, and Functional

  5. Piezoelectric transducer array microspeaker

    Carreno, Armando Arpys Arevalo

    2016-12-19

    In this paper we present the fabrication and characterization of a piezoelectric micro-speaker. The speaker is an array of micro-machined piezoelectric membranes, fabricated on silicon wafer using advanced micro-machining techniques. Each array contains 2n piezoelectric transducer membranes, where “n” is the bit number. Every element of the array has a circular shape structure. The membrane is made out four layers: 300nm of platinum for the bottom electrode, 250nm or lead zirconate titanate (PZT), a top electrode of 300nm and a structural layer of 50

  6. P systems with array objects and array rewriting rules

    K.G. Subramanian; R. Saravanan; M. Geethalakshmi; P. Helen Chandra; M. Margenstern

    2007-01-01

    Array P systems were introduced by Pǎun Gh. which is linking the two areas of membrane computing and picture grammars. Puzzle grammars were introduced by us for generating connected picture arrays in the two-dimensional plane, motivated by the problem of tiling the plane. On the other hand, incorporating into arrays the developmental type of generation used in the well-known biologically motivated L systems, Siromoney and Siromoney proposed a very general rectangular array generating model, called extended controlled tabled L array system (ECTLAS). In this paper we introduce two variations of the array P system, called BPG array P system and parallel array P system. The former has in the regions array objects and basic puzzle grammar rules (BPG), which are a specific kind of puzzle grammar rules. In the latter, the regions have rectangular array objects and tables of context-free rules. We examine these two types of P systems for their array generative power.

  7. Mitral valve finite element modeling: implications of tissues' nonlinear response and annular motion.

    Stevanella, Marco; Votta, Emiliano; Redaelli, Alberto

    2009-12-01

    Finite element modeling represents an established method for the comprehension of the mitral function and for the simulation of interesting clinical scenarios. However, current models still do not include all the key aspects of the real system. We implemented a new structural finite element model that considers (i) an accurate morphological description of the valve, (ii) a description of the tissues' mechanical properties that accounts for anisotropy and nonlinearity, and (iii) dynamic boundary conditions that mimic annulus and papillary muscles' contraction. The influence of such contraction on valve biomechanics was assessed by comparing the computed results with the ones obtained through an auxiliary model with fixed annulus and papillary muscles. At the systolic peak, the leaflets' maximum principal stress contour showed peak values in the anterior leaflet at the strut chordae insertion zone (300 kPa) and near the annulus (200-250 kPa), while much lower values were detected in the posterior leaflet. Both leaflets underwent larger tensile strains in the longitudinal direction, while in the circumferential one the anterior leaflet experienced nominal tensile strains up to 18% and the posterior one experienced compressive strains up to 23% associated with the folding of commissures and paracommissures, consistently with tissue redundancy. The force exerted by papillary muscles at the systolic peak was equal to 4.11 N, mainly borne by marginal chordae (76% of the force). Local reaction forces up to 45 mN were calculated on the annulus, leading to tensions of 89 N/m and 54 N/m for its anterior and posterior tracts, respectively. The comparison with the results of the auxiliary model showed that annular contraction mainly affects the leaflets' circumferential strains. When it was suppressed, no more compressive strains could be observed and peak strain values were located in the belly of the anterior leaflet. Computational results agree to a great extent with

  8. Investigation of heat transfer and pressure drop in an annular channel with heat transfer intensifiers

    Boltenko, E. A.; Varava, A. N.; Dedov, A. V.; Zakharenkov, A. V.; Komov, A. T.; Malakhovskii, S. A.

    2015-03-01

    Results from systematic investigations of heat transfer and pressure drop for water flow in an annular channel using an efficient method for enhancing heat transfer on a convex heating surface are presented. The main technical data of the thermal-hydraulic experimental setup are given together with a brief description of the control, monitoring, and physical parameters measurement and recording systems, as well as primary experimental data processing and storage system. The test section, the enhancement method based on setting up swirl flows, the geometrical characteristics of intensifiers, their schematic design, and installation technology are described. The experimental data are obtained in a wide range of coolant flow parameters under the conditions of single-phase convection with using intensifiers having different shapes. The test measurements carried out on a smooth annular channel showed good agreement with the classic correlations both for heat transfer and pressure drop, thereby confirming reliability of the experimental data. A considerable improvement in heat removal efficiency on the convex heating surface is obtained. The value of heat transfer coefficient is a factor of 1.8 higher than it is for smooth annular channels. The region of the values of intensifier geometrical characteristics and Reynolds numbers for which the growth of heat transfer prevails over the growth of pressure drop is established. It is shown that the maximums of heat transfer and pressure drop are observed at quite definite values of intensifier geometrical characteristics. The primary experimental data are processed and presented as a dependence of the Nusselt number on the Reynolds number for different values of the intensifier's relative fin height Ḣ. The value of Ḣ at which heat transfer reaches its maximum is found. The experiments were carried out in the pressure range p = 3.0-10.0 MPa and at the constant temperature of liquid at the test section inlet equal to 100

  9. De Vega annuloplasty for functional tricupsid regurgitation: concept of tricuspid valve orifice index to optimize tricuspid valve annular reduction.

    Hwang, Ho Young; Chang, Hyoung Woo; Jeong, Dong Seop; Ahn, Hyuk

    2013-12-01

    We evaluated long-term results of De Vega annuloplasty measured by cylindrical sizers for functional tricuspid regurgitation (FTR) and analyzed the impact of measured annular size on the late recurrence of tricuspid valve regurgitation. Between 2001 and 2011, 177 patients (57.9±10.5 yr) underwent De Vega annuloplasty for FTR. Three cylindrical sizers (actual diameters of 29.5, 31.5, and 33.5 mm) were used to reproducibly reduce the tricuspid annulus. Long-term outcomes were evaluated and risk factor analyses for the recurrence of FTR ≥3+ were performed. Measured annular diameter indexed by patient's body surface area was included in the analyses as a possible risk factor. Operative mortality occurred in 8 patients (4.5%). Ten-year overall and cardiac death-free survivals were 80.5% and 90.8%, respectively. Five and 10-yr freedom rates from recurrent FTR were 96.5% and 93.1%, respectively. Cox proportional hazard model revealed that higher indexed annular size was the only risk factor for the recurrence of FTR (P=0.006). A minimal P value approach demonstrated that indexed annular diameter of 22.5 mm/m(2) was a cut-off value predicting the recurrence of FTR. De Vega annuloplasty for FTR results in low rates of recurrent FTR in the long-term. Tricuspid annulus should be reduced appropriately considering patients' body size to prevent recurrent FTR.

  10. Predicting the Mean Liquid Film Thickness and Profile along the Annular Length of a Uniformly Heated Channel at Dryout

    V.Y. Agbodemegbe

    2011-03-01

    Full Text Available The objective of this study was to predict the mean liquid film thickness and profile at high shear stress using a mechanistic approach. Knowledge of the liquid film thickness and its variation with two-phase flow parameters is critical for the estimation of safety parameters in the annular flow regime. The mean liquid film thickness and profile were predicted by the PLIFT code designed in Fortran 95 programming language using the PLATO FTN95 compiler. The film thickness was predicted within the annular flow regime for a flow boiling quality ranging from 40 to 80 % at high interfacial shear stress. Results obtained for a laminar liquid film flow were dumped into an excel file when the ratio of the actual predicted film thickness to the critical liquid film thickness lied within the range of 0.9 to unity. The film thickness was observed to decrease towards the exit of the annular regime at high flow boiling qualities and void fractions. The observation confirmed the effect of evaporation in decreasing the film thickness as quality is increased towards the exit of the annular regime.

  11. Dual-polarization light emission from InAs quantum dots in a annular photonic crystal cavity

    Jiang, Liyong; Wu, Hong; Zhang, Wei; Su, Wei; Li, Xiangyin

    2014-01-01

    The annular photonic crystals have been regarded as a satisfactory candidate to realize dual-polarization photonic device. In this letter, we focus our attention on the study of annular photonic crystal cavity to verify its application in light emission. We proposed a two-dimensional photonic crystal model with annular air units and a point-line defect to construct a cavity for the enhancement of light emission of InAs quantum dots. With the help of global optimization method, we have obtained an annular photonic crystal cavity design which can show a high in-plane quality factor of about 1.3*105 and 2.8*106 for transverse electric and transverse magnetic polarizations, respectively. Based on the Electron Beam Lithography and Reactive Ion Etching techniques, such cavity pattern was transferred into the top of InAs/GaAs active layer. The photoluminescence spectra of sample demonstrated clear light emission at around 1.3 um for both polarizations. Such dual-polarization light emitter has potential applications ...

  12. Replacement of annular domain with trapezoidal domain in computational modeling of nonaqueous-phase-liquid dissolution-front propagation problems

    ZHAO Chong-bin; Thomas POULET; Klaus REGENAUER-LIEB

    2015-01-01

    In order to simulate the instability phenomenon of a nonaqueous phase liquid (NAPL) dissolution front in a computational model, the intrinsic characteristic length is commonly used to determine the length scale at which the instability of the NAPL dissolution front can be initiated. This will require a huge number of finite elements if a whole NAPL dissolution system is simulated in the computational model. Even though modern supercomputers might be used to tackle this kind of NAPL dissolution problem, it can become prohibitive for commonly-used personal computers to do so. The main purpose of this work is to investigate whether or not the whole NAPL dissolution system of an annular domain can be replaced by a trapezoidal domain, so as to greatly reduce the requirements for computer efforts. The related simulation results have demonstrated that when the NAPL dissolution system under consideration is in a subcritical state, if the dissolution pattern around the entrance of an annulus domain is of interest, then a trapezoidal domain cannot be used to replace an annular domain in the computational simulation of the NAPL dissolution system. However, if the dissolution pattern away from the vicinity of the entrance of an annulus domain is of interest, then a trapezoidal domain can be used to replace an annular domain in the computational simulation of the NAPL dissolution system. When the NAPL dissolution system under consideration is in a supercritical state, a trapezoidal domain cannot be used to replace an annular domain in the computational simulation of the NAPL dissolution system.

  13. Protein Functionalized Nanodiamond Arrays

    Liu YL

    2010-01-01

    Full Text Available Abstract Various nanoscale elements are currently being explored for bio-applications, such as in bio-images, bio-detection, and bio-sensors. Among them, nanodiamonds possess remarkable features such as low bio-cytotoxicity, good optical property in fluorescent and Raman spectra, and good photostability for bio-applications. In this work, we devise techniques to position functionalized nanodiamonds on self-assembled monolayer (SAMs arrays adsorbed on silicon and ITO substrates surface using electron beam lithography techniques. The nanodiamond arrays were functionalized with lysozyme to target a certain biomolecule or protein specifically. The optical properties of the nanodiamond-protein complex arrays were characterized by a high throughput confocal microscope. The synthesized nanodiamond-lysozyme complex arrays were found to still retain their functionality in interacting with E. coli.

  14. Simulation and performance of an artificial retina for 40 MHz track reconstruction

    2014-01-01

    We present the results of a detailed simulation of the artificial retina pattern-recognition algorithm, designed to reconstruct events with hundreds of charged-particle tracks in pixel and silicon detectors at LHCb with LHC crossing frequency of $40\\,\\rm MHz$. Performances of the artificial retina algorithm are assessed using the official Monte Carlo samples of the LHCb experiment. We found performances for the retina pattern-recognition algorithm comparable with the full LHCb reconstruction ...

  15. Experimental study of horizontal annular channels under non-developed conditions

    Delgadino, G. [Rensselaer Polytechnic Institute, Troy, NY (United States); Balino, J.; Carrica, P. [Centro Atomico Bariloche e Instituto Balseriro (Argentina)

    1995-09-01

    In this work an experimental study of the two-phase air-water flow in a horizontal annular channel under non-developed conditions is presented. A conductive local probe was placed at the end of the channel to measure the local phase indication function under a wide range of gas and water flow rates. The signal was processed to obtain the void fraction and statistical distributions of liquid and gas residence times. From these data the topology of the flow could be inferred. A laser intermittence detector was also located close to the channel exit, in order to measure statistical parameters for intermittent flows by means of a two-probe method.

  16. Correlation and spectral measurements of fluctuating pressures and velocities in annular turbulent flow. [PWR; BWR

    Wilson, R.J.; Jones, B.G.; Roy, R.P.

    1980-02-01

    An experimental study of the fluctuating velocity field, the fluctuating static wall pressure and the in-stream fluctuating static pressure in an annular turbulent air flow system with a radius ratio of 4.314 has been conducted. The study included direct measurements of the mean velocity profile, turbulent velocity field; fluctuating static wall pressure and in-stream fluctuating static pressure from which the statistical values of the turbulent intensity levels, power spectral densities of the turbulent quantities, the cross-correlation between the fluctuating static wall pressure and the fluctuating static pressure in the core region of the flow and the cross-correlation between the fluctuating static wall pressure and the fluctuating velocity field in the core region of the flow were obtained.

  17. Prospects for lithium imaging using annular bright field scanning transmission electron microscopy: A theoretical study

    Findlay, S.D., E-mail: scott@sigma.t.u-tokyo.ac.jp [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); Lugg, N.R. [School of Physics, University of Melbourne, Parkville, Victoria 3010 (Australia); Shibata, N. [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); PRESTO, Japan Science and Technology Agency, Saitama 332-0012 (Japan); Allen, L.J. [School of Physics, University of Melbourne, Parkville, Victoria 3010 (Australia); Ikuhara, Y. [Institute of Engineering Innovation, The University of Tokyo, Tokyo 116-0013 (Japan); Nanostructures Research Laboratory, Japan Fine Ceramic Center, Nagoya 456-8587 (Japan); WPI Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan)

    2011-07-15

    There is strong interest in lithium imaging, particularly because of its significance in battery materials. However, light atoms only scatter electrons weakly and atomic resolution direct imaging of lithium has proven difficult. This paper explores theoretically the conditions under which lithium columns can be expected to be directly visible using annular bright field scanning transmission electron microscopy. A detailed discussion is given of the controllable parameters and the conditions most favourable for lithium imaging. -- Highlights: {yields} Optimum conditions to image Li columns in Li-bearing materials with ABF are explored. {yields} Higher accelerating voltages give better contrast at a given resolution. {yields} Aperture size must compromise between resolution and good coupling to the column. {yields} Samples with small along-column interatomic spacing between Li atoms are best. {yields} The trends observed are consistent with prediction based on the s-state model.

  18. Study on Dielectric Resonator Antenna with Annular Patch for High Gain and Large Bandwidth

    FENG Kuisheng; LI Na; MENG Qingwei; WANG Yongfeng; ZHANG Jingwei

    2015-01-01

    A new high-gain cylindrical Dielectric res-onator antenna (DRA) with a large bandwidth is proposed. A cylindrical Dielectric resonator (DR), a double-annular patch and a metallic cylinder are used to obtain a large bandwidth and a high gain. The mode TM12 excited in the patch is used to enhance the gain of the DRA, and the cavity formed by the metallic cylinder provides a further higher gain and a larger bandwidth. The measured results demonstrate that the proposed DRA achieves a large band-width of 23%from 5.3 to 6.8GHz with VSWR less than two and a high gain around 11 dBi.

  19. Is there a robust effect of anthropogenic aerosols on the Southern Annular Mode?

    Steptoe, H.; Wilcox, L. J.; Highwood, E. J.

    2016-09-01

    Historical anthropogenic aerosol (AA) changes are found to have caused a statistically significant negative Southern Annular Mode (SAM) trend (associated with an equatorward jet shift) in 14 out of 35 individual ensemble members from the fifth Coupled Model Intercomparison Project (CMIP5) since 1860. However, this response is not robust. The significance of the SAM response to aerosol is model dependent and not simply related to aerosol forcing. Multiple sources of uncertainty result in a nonrobust response that means that the model mechanism connecting remote Northern Hemisphere AA forcing remains unclear. Analysis of single forcing experiments suggests that assuming the climate response to individual model forcings to be linearly additive cannot be made without proper assessment. Our results suggest that AAs may have had a historical influence on the SAM, but its influence may be overstated by assuming linearity.

  20. Analytical and numerical study of the electro-osmotic annular flow of viscoelastic fluids.

    Ferrás, L L; Afonso, A M; Alves, M A; Nóbrega, J M; Pinho, F T

    2014-04-15

    In this work we present semi-analytical solutions for the electro-osmotic annular flow of viscoelastic fluids modeled by the Linear and Exponential PTT models. The viscoelastic fluid flows in the axial direction between two concentric cylinders under the combined influences of electrokinetic and pressure forcings. The analysis invokes the Debye-Hückel approximation and includes the limit case of pure electro-osmotic flow. The solution is valid for both no slip and slip velocity at the walls and the chosen slip boundary condition is the linear Navier slip velocity model. The combined effects of fluid rheology, electro-osmotic and pressure gradient forcings on the fluid velocity distribution are also discussed.

  1. Investigations of the torque anomaly in an annular sector. I. Global calculations, scalar case

    Milton, Kimball A; Parashar, Prachi; Abalo, E K; Fulling, Stephen A; Bouas, Jeffrey D; Carter, Hamilton; Kirsten, Klaus

    2013-01-01

    In an attempt to understand a recently discovered torque anomaly in quantum field theory with boundaries, we calculate the Casimir energy and torque of a scalar field subject to Dirichlet boundary conditions on an annular sector defined by two coaxial cylinders intercut by two planes through the axis. In this model the particularly troublesome divergence at the cylinder axis does not appear, but new divergences associated with the curved boundaries are introduced. All the divergences associated with the volume, the surface area, the corners, and the curvature are regulated by point separation either in the direction of the axis of the cylinder or in the (Euclidean) time; the full divergence structure is isolated, and the remaining finite energy and torque are extracted. Formally, only the regulator based on axis splitting yields the expected balance between energy and torque. Because of the logarithmic curvature divergences, there is an ambiguity in the linear dependence of the energy on the wedge angle; if t...

  2. Long-lived lop-sided modes of annular disks orbiting a central mass

    Jacobs, V

    2001-01-01

    We demonstrate the existence of long-lived, large-amplitude eccentric modes in massive, annular particle disks in orbit about a central mass. The lopsided modes we have found precess slowly in the prograde direction at a rate which increases with disk mass and decreases with the amplitude of the distortion. The lopsidedness generally survives for as long as we run the calculations and may last indefinitely; we found no significant decay in over 700 disk-particle orbits in one case. These strongly non-linear modes are readily created using a number of different perturbing rules, but we find no evidence for linear instabilities in unperturbed disks. Our results suggest that Tremaine's eccentric disk model for the nucleus of M31 may be viable, but none of our models matches all aspects of the observational data.

  3. Thermal analysis of annular fins with temperature-dependent thermal properties

    I. G. AKSOY

    2013-01-01

    The thermal analysis of the annular rectangular profile fins with variable thermal properties is investigated by using the homotopy analysis method (HAM). The thermal conductivity and heat transfer coefficient are assumed to vary with a linear and power-law function of temperature, respectively. The effects of the thermal-geometric fin parameter and the thermal conductivity parameter variations on the temperature distribution and fin efficiency are investigated for different heat transfer modes. Results from the HAM are compared with numerical results of the finite difference method (FDM). It can be seen that the variation of dimensionless parameters has a significant effect on the temperature distribution and fin efficiency.

  4. Multiphysics Modeling of an Annular Linear Induction Pump With Applications to Space Nuclear Power Systems

    Kilbane, J.; Polzin, K. A.

    2014-01-01

    An annular linear induction pump (ALIP) that could be used for circulating liquid-metal coolant in a fission surface power reactor system is modeled in the present work using the computational COMSOL Multiphysics package. The pump is modeled using a two-dimensional, axisymmetric geometry and solved under conditions similar to those used during experimental pump testing. Real, nonlinear, temperature-dependent material properties can be incorporated into the model for both the electrically-conducting working fluid in the pump (NaK-78) and structural components of the pump. The intricate three-phase coil configuration of the pump is implemented in the model to produce an axially-traveling magnetic wave that is qualitatively similar to the measured magnetic wave. The model qualitatively captures the expected feature of a peak in efficiency as a function of flow rate.

  5. A shallow-water theory for annular sections of Keplerian Disks

    Umurhan, O M

    2008-01-01

    A scaling argument is presented that leads to a shallow water theory of non-axisymmetric disturbances in annular sections of thin Keplerian disks. The aims of this study is to develop a theoretical construction that will aid in physically understanding the relationship of known two-dimensional vortex dynamics to their three-dimensional counterparts in Keplerian disks. Using asymptotic scaling arguments varicose disturbances of a Keplerian disk are considered on radial and vertical scales consistent with the height of the disk while the azimuthal scales are the full $2\\pi$ angular extent of the disk. For simplicity perturbations are assumed to be homentropic according to a polytropic equation of state. The timescales considered are long compared to the local disk rotation time. The scalings lead to dynamics which are radially geostrophic and vertically hydrostatic. It follows that a potential vorticity quantity emerges and is shown to be conserved in a Lagrangian sense. Uniform potential vorticity solutions, b...

  6. Extended depth of field using a liquid crystal annular spatial light modulator.

    Klapp, Iftach; Solodar, Asi; Abdulhalim, Ibrahim

    2014-07-01

    A detailed investigation is presented on the tunable extended depth of field (EDOF) method, proposed recently by Klapp et al. [Opt. Lett.39, 1414 (2014)]. This method is based on temporal multiplexing of phase masks, using an annular liquid crystal spatial light modulator possessing a small number of rings. Examples of 3D simulations used to determine the phase profiles in the pupil plane are presented, as well as more detailed experimental results. Both the experimental and numerical results include comprehensive analysis of contrast dependence on both the spatial spectrum of the object and the amount of defocus. In addition, for the first time, we present the EDOF order inversion in the experimental and simulated data. The results show a profound performance of the proposed system and method.

  7. The impact of the Southern Annular Mode on future changes in Southern Hemisphere rainfall

    Lim, Eun-Pa; Hendon, Harry H.; Arblaster, Julie M.; Delage, Francois; Nguyen, Hanh; Min, Seung-Ki; Wheeler, Matthew C.

    2016-07-01

    A robust positive trend in the Southern Annular Mode (SAM) is projected for the end of the 21st century under the Representative Concentration Pathway 8.5 scenario, which results in rainfall decreases in the midlatitudes and increases in the high latitudes in the Southern Hemisphere (SH). We find that this SAM trend also increases rainfall over the SH subtropics in austral summer but not in winter, leading to a pronounced wintertime poleward expansion of the subtropical dry zone. These dynamically driven rainfall changes by the SAM appear to oppose the thermodynamically driven projected rainfall changes in the SH subtropics and midlatitudes, whereas the two components reinforce each other in the high latitudes. However, we show that most climate models fall short in capturing the observed SAM component driven by the El Niño-Southern Oscillation and associated rainfall in the austral warm seasons, which limits our confidence in quantifying the contribution of the SAM to projected rainfall changes.

  8. A rare presentation of subcutaneous granuloma annulare in an adult patient; A case report

    Waleed Alajroush

    2016-07-01

    Full Text Available We are reporting a 33-year old woman with multiple skin-colored, firm, non-tender nodules of varying sizes (ranging between 1 and 1.5 cm, with limited mobility and normal overlying skin. They were distributed mainly on the palmer side of the fingers. History and laboratory examination indicated lack of systemic diseases such as diabetes, rheumatoid arthritis, and tuberculosis. Histopathologic examination confirmed the subcutaneous granuloma annulare (SGA diagnosis by showing a normal epidermis with palisading granulomas (histocytes and giant cells surrounding small areas of connective tissue degeneration (central necrobiosis and mucin accumulation in the reticular dermis and subcutaneous tissues. The patient responded well to two-session course of intra-lesional steroid injections. SGA should be considered by dermatologists in the differential diagnosis of subcutaneous nodules even without concomitant systemic disease and with rare presentation.

  9. Cryosphere-atmosphere interaction related to variability and change of northern hemisphere annular mode.

    Bojariu, Roxana; García-Herrera, Ricardo; Gimeno, Luis; Zhang, Tingjun; Frauenfeld, Oliver W

    2008-12-01

    The Northern Hemisphere annular mode, also known as the Arctic Oscillation/North Atlantic Oscillation (AO/NAO) is a dominant atmospheric mode in the Northern Hemisphere winter that influences climate fluctuations from the eastern seaboard of the United States to Siberia and from the Arctic to the subtropical Atlantic. After almost a century of scientific investigation, the fundamental mechanisms determining the evolution of the AO/NAO are not yet completely understood. The ocean is favored as the most likely forcing of atmospheric variability, given the time scales of oceanic circulation and its large heat capacity. Our analyses of snow cover, soil temperatures, zonal winds, and geopotential heights identify the effect of land-atmosphere interaction over Eurasia on Northern Hemisphere atmospheric circulation, explaining the predictive signal that links fluctuations of April-October snow cover with the following winter AO/NAO phases.

  10. Forced convection to laminar flow of liquid egg yolk in circular and annular ducts

    M. Bernardi

    2009-06-01

    Full Text Available The steady-state heat transfer in laminar flow of liquid egg yolk - an important pseudoplastic fluid food - in circular and concentric annular ducts was experimentally investigated. The average convection heat transfer coefficients, determined by measuring temperatures before and after heating sections with constant temperatures at the tube wall, were used to obtain simple new empirical expressions to estimate the Nusselt numbers for fully established flows at the thermal entrance of the considered geometries. The comparisons with existing correlations for Newtonian and non-Newtonian fluids resulted in excellent agreement. The main contribution of this work is to supply practical and easily applicable correlations, which are, especially for the case of annulus, rather scarce and extensively required in the design of heat transfer operations dealing with similar shear-thinning products. In addition, the experimental results may support existing theoretical analyses.

  11. Algebraically explicit analytical solutions for the unsteady non-Newtonian swirling flow in an annular pipe

    CAI; Ruixian; GOU; Chenhua

    2006-01-01

    This paper presents two algebraically explicit analytical solutions for the incompressible unsteady rotational flow of Oldroyd-B type in an annular pipe. The first solution is derived with the common method of separation of variables. The second one is deduced with the method of separation of variables with addition developed in recent years. The first analytical solution is of clear physical meaning and both of them are fairly simple and valuable for the newly developing computational fluid dynamics. They can be used as the benchmark solutions to verify the applicability of the existing numerical computational methods and to inspire new differencing schemes, grid generation ways, etc. Moreover, a steady solution for the generalized second grade rheologic fluid flow is also presented. The correctness of these solutions can be easily proven by substituting them into the original governing equation.

  12. Bifurcation of thermocapillary convection in a shallow annular pool of silicon melt

    Yourong Li; Lan Peng; Shuangying Wu; Nobuyuki Imaishi

    2007-01-01

    In order to understand the nature ofsurface patterns on silicon melts in industrial Czochral-ski furnaces,we conducted a series of unsteady three-dimensional numerical simulations of thermocapillaryconvections in thin silicon melt pools in an annular con-tainer.The pool is heated from the outer cylindrical walland cooled at the inner wall.Bottom and top surfacesare adiabatic.The results show that the flow is steadyand axisymmetric at small temperature difference inthe radial direction.When the temperature differenceexceeds a certain threshold value,hydrothermal wavesappear and bifurcation occurs.In this case,the flow is un-steady and there are two possible groups of hydrother-mal waves with different number of waves,which arecharacterized by spoke patterns traveling in the clock-wise and counter-clockwise directions.Details of theflow and temperature disturbances are discussed andnumber of waves and traveling velocity of the hydro-thermal wave are determined.

  13. Aortic valve replacement with concomitant annular enlargement for small aortic annulus of less than 19 mm.

    Takakura, H; Sasaki, T; Hashimoto, K; Hachiya, T; Onoguchi, K; Oshiumi, M; Takeuchi, S

    2000-06-01

    Three female patients with aortic stenosis associated with a severely small annulus underwent aortic valve replacement. In intraoperative measurements, a 19-mm obtulator could not pass through the aortic annulus in each case. We therefore concluded that it would be difficult to implant an appropriate-sized prosthesis in a routine fashion, so we performed an annular enlargement in a modified Nicks procedure. By using a wide teardrop-shaped patch for enlargement and slightly tilting insertion of a prosthesis, a 21 mm bileaflet mechanical prosthesis could be inserted into the enlarged annulus. Despite being a simpler method than other enlarging procedures, a two- or three-sizes larger prosthesis than the native annulus can be inserted with relative ease. Thus, the use of a 19 mm mechanical prosthesis may be avoidable in most adult cases.

  14. Characterization of the Annular Core Research Reactor (ACRR Neutron Radiography System Imaging Plane

    Kaiser Krista

    2016-01-01

    Full Text Available The Annular Core Research Reactor (ACRR at Sandia National Laboratories (SNL is an epithermal pool-type research reactor licensed up to a thermal power of 2.4 MW. The ACRR facility has a neutron radiography facility that is used for imaging a wide range of items including reactor fuel and neutron generators. The ACRR neutron radiography system has four apertures (65:1, 125:1, 250:1, and 500:1 available to experimenters. The neutron flux and spectrum as well as the gamma dose rate were characterized at the imaging plane for the ACRR's neutron radiography system for the 65:1, 125:1 and 250:1 apertures.

  15. Characterization of the Annular Core Research Reactor (ACRR) Neutron Radiography System Imaging Plane

    Kaiser, Krista; Chantel Nowlen, K.; DePriest, K. Russell

    2016-02-01

    The Annular Core Research Reactor (ACRR) at Sandia National Laboratories (SNL) is an epithermal pool-type research reactor licensed up to a thermal power of 2.4 MW. The ACRR facility has a neutron radiography facility that is used for imaging a wide range of items including reactor fuel and neutron generators. The ACRR neutron radiography system has four apertures (65:1, 125:1, 250:1, and 500:1) available to experimenters. The neutron flux and spectrum as well as the gamma dose rate were characterized at the imaging plane for the ACRR's neutron radiography system for the 65:1, 125:1 and 250:1 apertures.

  16. Heat transfer analysis in an annular cone subjected to power law variations

    Salman Ahmed, N. J.; Al-Rashed, Abdullah A. A. A.; Yunus Khan, T. M.; Kamangar, Sarfaraz; Athani, Abdulgaphur; Anjum Badruddin, Irfan

    2016-09-01

    Present study deals with the analysis of heat transfer and fluid flow behavior in an annular cone fixed with saturated porous medium. The inner surface of the cone is assumed to have power law variable wall temperature. The governing partial differential equations are solved using well known Finite Element Method (FEM). The coupled nonlinear differential equations are converted into the algebraic equations by using Galerkin method. A 3 noded triangular element is used to divide the porous domain into smaller segments. The effects of various geometrical parameters on the cone angle are presented. It is found that the effect of cone angle on the heat transfer characteristics and fluid flow behavior is considerably significant. The fluid moment is found to shift towards the upper side of cone with increase in the power law coefficient. The fluid velocity decreases with increase in the power law coefficient.

  17. Oil Stiction in Fast Switching Annular Seat Valves for Digital Displacement Fluid Power Machines

    Roemer, Daniel Beck; Johansen, Per; Pedersen, Henrik C.

    2014-01-01

    valves suitable for DD applications based on the Reynolds equation and considers contact surface curvature and attack angle. A dynamic cavitation zone is included in the stiction model, and cavitation is found to be present even for seat valves surrounded by high pressure levels....... to the dynamic behaviour of the seat valves must be considered to optimize the machine efficiency. A significant effect influencing the valves switching performance is the presence of oil stiction when separating the contact surfaces in valve opening movement. This oil stiction force is limited by cavitation...... for low pressure levels, e.g. valves connected to the low pressure manifold, however for valves operated at higher pressure levels, the oil stiction force is dominating when the separating surfaces are close to contact. This paper presents an analytic solution to the oil stiction force for annular seat...

  18. The Hydraulic Test Procedure for Non-instrumented Irradiation Test Rig of Annular Fuel

    Kim, Dae Ho; Lee, Kang Hee; Shin, Chang Hwan; Park, Chan Kook

    2008-08-15

    This report presents the procedure of pressure drop test, vibration test and endurance test for the non-instrumented rig using the irradiation test in HANARO of advanced PWR annular fuel which were designed and fabricated by KAERI. From the out-pile thermal hydraulic tests, confirm the flow rate at the 200 kPa pressure drop and measure the RMS displacement at this time. And the endurance test is confirmed the wear and the integrity of the non-instrumented rig at the 110% design flow rate. This out-pile test perform the Flow-Induced Vibration and Pressure Drop Experimental Tester(FIVPET) facility. The instruments in FIVPET facility was calibrated in KAERI and the pump and the thermocouple were certified by manufacturer.

  19. Experimental Investigation of the Three—Dimensional Flow in an Annular Compressor Cascade at Large Incidence

    TuhongLi; DajunYe; 等

    1992-01-01

    This paper presents a detalied experimental investigation concerning the influence of blade loading (incidence) on the three -dimensional flow in an annular compressor cascade.The data are acquired at four incidence angles under low Mach number and low Reynolds number conditions.ExPerimental techniques include the oil-film visualization on the profile and the endwall surfaces,the laser-sheet visualization of the flow field inside the blade passae,and the measurement by radial-circumferential traverses using a seven-hloe probe.The behavior and nature of the three-dimensional flow with severs separations inside the blade passage and at the exit are obtained.The distributions of the total pressure loss,static pressure.Velocity and outflow angle are also given.Theses results are valuable for establishing the physical model of the three-dimensional complex flow in axial compressor and for examinig the computational procedures.

  20. Optimizing the subwavelength grating of L-band Annular Groove Phase Masks for high coronagraphic performance

    Catalan, Ernesto Vargas; Forsberg, Pontus; Jolivet, Aïssa; Baudoz, Pierre; Carlomagno, Brunella; Delacroix, Christian; Habraken, Serge; Mawet, Dimitri; Surdej, Jean; Absil, Olivier; Karlsson, Mikael

    2016-01-01

    Context. The Annular Groove Phase Mask (AGPM) is one possible implementation of the vector vortex coronagraph, where the helical phase ramp is produced by a concentric subwavelength grating. For several years, we have been manufacturing AGPMs by etching gratings into synthetic diamond substrates using inductively coupled plasma etching. Aims. We aim to design, fabricate, optimize, and evaluate new L-band AGPMs that reach the highest possible coronagraphic performance, for applications in current and forthcoming infrared high-contrast imagers. Methods. Rigorous coupled wave analysis (RCWA) is used for designing the subwavelength grating of the phase mask. Coronagraphic performance evaluation is performed on a dedicated optical test bench. The experimental results of the performance evaluation are then used to accurately determine the actual profile of the fabricated gratings, based on RCWA modeling. Results. The AGPM coronagraphic performance is very sensitive to small errors in etch depth and grating profile....

  1. Radiation and Resonant Frequency of Superconducting Annular Ring Microstrip Antenna on Uniaxial Anisotropic Media

    Barkat, Ouarda; Benghalia, Abdelmadjid

    2009-10-01

    In this work, the full-wave method is used for computing the resonant frequency, the bandwidth, and radiation pattern of High temperature superconductor, or an imperfectly conducting annular ring microstrip, which is printed on uniaxial anisotropic substrate. Galerkin’s method is used in the resolution of the electric field integral equation. The TM set of modes issued from the cavity model theory are used to expand the unknown currents on the patch. Numerical results concerning the effect of the anisotropic substrates on the antenna performance are presented and discussed. It is found that microstrip superconducting could give high efficiency with high gain in millimeter wavelengths. Results are compared with previously published data and are found to be in good agreement.

  2. Development of Full Automatic External Welding Machine for Annular Welds of Pipeline

    FengBiao; LiChunrun; TangDeyu; ZhangJianhu; ZhangTianli

    2004-01-01

    To meet the demands of rapid development of pipeline constructions in China, a complete set of full automatic external welding machine for annular welds of pipeline and welding procedure have been developed thereof. The system has been applied in the “West-East Pipeline Project” and its performance is proven. With this welding machine the welding parameters can be either preset before or adjusted in real time during the welding process, which avoids the blemishes of same type domestic and international products. Thus it is best propitious to in-situ construction conditions and workers' technical level in China. In this article the development of mechanical and control systems of this product is introduced and typical welding procedure parameters are provided.

  3. Stability analysis of thermo-acoustic nonlinear eigenproblems in annular combustors. Part I. Sensitivity

    Magri, Luca; Juniper, Matthew

    2016-01-01

    We present an adjoint-based method for the calculation of eigenvalue perturbations in nonlinear, degenerate and non self-adjoint eigenproblems. This method is applied to a thermo-acoustic annular combustor network, the stability of which is governed by a nonlinear eigenproblem. We calculate the first- and second-order sensitivities of the growth rate and frequency to geometric, flow and flame parameters. Three different configurations are analysed. The benchmark sensitivities are obtained by finite difference, which involves solving the nonlinear eigenproblem at least as many times as the number of parameters. By solving only one adjoint eigenproblem, we obtain the sensitivities to any thermo-acoustic parameter, which match the finite-difference solutions at much lower computational cost.

  4. Ultracompact optical circulator based on a uniformly magnetic magnetophotonic annular Bragg cavity

    Śmigaj, Wojciech; Romero-Vivas, Javier; Guenneau, Sébastien; Dagens, Béatrice; Gralak, Boris; Vanwolleghem, Mathias

    2011-01-01

    We have developed a theoretical framework that allows an efficient design of integrated optical circulators based on non-reciprocal magneto-optical cavities. Using this approach we have analysed different possible layouts for nonreciprocal resonant cavities. This investigation has allowed us to propose a new class of miniaturized integrated optical circulators that achieve simultaneously strong optical circulation while maintaining reasonable technological feasibility. Their layout is based on a radial Bragg cavity formed by arranging centrosymmetric annular magneto-optic rings. The circulator ports are standard rib waveguides, butt-coupled to the ring cavity by possibly cutting the outer cavity rings. Using a coupled mode description of the complete cavity/waveguide-port system, it is shown that it is indispensable to take possible direct port-to-port coupling into account for a proper optimization of the device. Including these optimization parameters in finite element simulations has led us to propose a st...

  5. A two-dimensional parabolic model for vertical annular two-phase flow

    Fernandez, F.M.; Toledo, A. Alvarez; Paladino, E.E. [Graduate Program in Mechanical Engineering, Universidade Federal de Rio Grande do Norte, Natal, RN (Brazil)], e-mail: emilio@ct.ufrn.br

    2010-07-01

    This work presents a solution algorithm for predicting hydrodynamic parameters for developing and equilibrium, adiabatic, annular, vertical two-phase flow. It solves mass and momentum transport differential equations for both the core and the liquid film across their entire domains. Thus, the velocity and shear stress distributions from the tube center to the wall are obtained, together with the average film thickness and the pressure gradient, making no use of empirical closure relations nor assuming any known velocity profile to solve the triangular relationship in the liquid film. The model was developed using the Finite Volume Method and an iterative procedure is proposed to solve all flow variables for given phase superficial velocities. The procedure is validated against the analytical solution for laminar flow and experimental data for gas-liquid turbulent flow with entrainment. For the last case, an algebraic turbulence model is used for turbulent viscosity calculation for both, liquid film and gas core. (author)

  6. Correction of edge-flame propagation speed in a counterflow, annular slot burner

    Tran, Vu Manh

    2015-10-22

    To characterize the propagation modes of flames, flame propagation speed must be accurately calculated. The impact of propagating edge-flames on the flow fields of unburned gases is limited experimentally. Thus, few studies have evaluated true propagation speeds by subtracting the flow velocities of unburned gases from flame displacement speeds. Here, we present a counterflow, annular slot burner that provides an ideal one-dimensional strain rate and lengthwise zero flow velocity that allowed us to study the fundamental behaviors of edge-flames. In addition, our burner has easy optical access for detailed laser diagnostics. Flame displacement speeds were measured using a high-speed camera and related flow fields of unburned gases were visualized by particle image velocimetry. These techniques allowed us to identify significant modifications to the flow fields of unburned gases caused by thermal expansion of the propagating edges, which enabled us to calculate true flame propagation speeds that took into account the flow velocities of unburned gases.

  7. Rayleigh-Bénard convection in a vertical annular container near the convection threshold.

    Wang, Bo-Fu; Wan, Zhen-Hua; Ma, Dong-Jun; Sun, De-Jun

    2014-04-01

    The instabilities and transitions of flow in an annular container with a heated bottom, a cooled top, and insulated sidewalls are studied numerically. The instabilities of the static diffusive state and of axisymmetric flows are investigated by linear stability analysis. The onset of convection is independent of the Prandtl number but determined by the geometry of the annulus, i.e., the aspect ratio Γ (outer radius to height) and radius ratio δ (inner radius to outer radius). The stability curves for onset of convection are presented for 0.001≤δ≤0.8 at six fixed aspect ratios: Γ=1, 1.2, 1.6, 1.75, 2.5, and 3.2. The instability of convective flow (secondary instability), which depends on both the annular geometry and the Prandtl number, is studied for axisymmetric convection. Two pairs of geometric control parameters are chosen to perform the secondary instability analysis-Γ=1.2, δ=0.08 and Γ=1.6, δ=0.2-and the Prandtl number ranges from 0.02 to 6.7. The secondary instability exhibits some similarities to that for convection in a cylinder. A hysteresis stability loop is found for Γ=1.2, δ=0.08 and frequent changes of critical mode with Prandtl number are found for Γ=1.6, δ=0.2. The three-dimensional flows beyond the axisymmetry-breaking bifurcations are obtained by direct numerical simulation for Γ=1.2, δ=0.08.

  8. The equatorial ionospheric response over Tirunelveli to the 15 January 2010 annular solar eclipse: observations

    C. K. Nayak

    2012-09-01

    Full Text Available In this paper we present a case study of the annular solar eclipse effects on the ionization of E and F regions of equatorial ionosphere over Tirunelveli [77.8° E, 8.7° N, dip 0.4° N] by means of digital ionosonde on 15 January 2010. The maximum obscuration of the eclipse at this station was 84% and it occurred in the afternoon. The E and F1 layers of the ionosphere showed very clear decrease in their electron concentrations, whereas the F2 layer did not show appreciable changes. A reduction of 30% was observed in the foF1 during the maximum phase of the eclipse. During the beginning phase of the eclipse, an enhancement of 0.97 MHz was observed in the foF2 as compared to that of the control days. But the foF2 decreased gradually as the eclipse progressed and a decrease of 0.59 MHz was observed towards the end phase of the eclipse. Observed variations in the h'F2 and hmF2 showed lower values than the control days, although hmF2 was found to increase a bit during the eclipse. Observed variability in the E, F1 and F2 layer ionospheric parameters on the eclipse day and their departure from the control days are discussed as the combined effect of annular eclipse and presence of counter equatorial electrojet (CEEJ.

  9. SHAPE EFFECT OF ANNULAR CONCENTRATOR IN ULTRASONIC SYSTEM ON AMPLIFICATION FACTOR OF VIBRATIONS AMPLITUDE

    D. A. Stepanenko

    2016-01-01

    Full Text Available The paper contains a theoretical underpinning on creation of ultrasonic vibration concentrators based on annular elastic elements with non-circular (ellipse-like eccentric shape of internal contour. Shape of internal contour in polar coordinates is described by Fourier series relative to angular coordinate that consists of a constant term and first and second harmonics. An effect of geometric parameters of the concentrator on amplification factor and natural vibration frequencies has been investigated with the help of a finite element method. The paper reveals the possibility to control an amplification factor of annular concentrators while varying eccentricity of internal contour and mean value of cross-section thickness. The amplification factor satisfies a condition K < N, where N is thickness ratio of amplifier input and output sections, and it is decreasing with increase of vibration mode order. The similar condition has been satisfied for conical bar concentrator with the difference that in the case of bar concentrators an amplification is ensured due to variation of diameter and N will represent ratio of diameters. It has been proved that modification of internal contour shape makes it possible to carry out a wide-band tuning of natural frequencies of concentrator vibrations without alteration of its overall dimensions and substantial change of amplification factor, which is important for frequency matching of the concentrator and ultrasonic vibratory system. Advantages of the proposed concentrators include simplicity of design and manufacturing, small overall dimensions, possibility for natural frequency tuning by means of static load variation. The developed concentrators can find their application in ultrasonic devices and instruments for technological and medical purposes.

  10. Annular sub-aperture stitching interferometry testing for large-caliber aspheric

    Wu, Pengfei; Yang, Shuming; Sun, Lin; Zhao, Pu; Jiang, Zhuangde

    2016-09-01

    An annular sub-aperture stitching interferometry testing is proposed for large-caliber aspheric lens testing, expanding the dynamic range of the interferometer, broadening the scope of the measurement, and reducing the cost of the measurement to a large extent without the use of compensating elements. The large-caliber aspheric is divided into several annular sub-apertures, and there are some overlapping areas between each two adjacent sub-apertures. When testing, the test aspheric is moved along the optical axis according to path planning so that the reference spherical shape and the test aspheric interest at points of common tangency to reduce the fringe density of the sub-aperture. However, in the process of moving the test optic, six DOF (degrees of freedom) misalignment errors will occur. According to the rigid body kinematics theory, the misalignment error separation model is established so that the misalignment factors can be calculated by the information of each overlapping regions. Then all sub-apertures are unified to the same reference with proper algorithm, and subsequently, misalignment error of the reference is removed by Zernike polynomial fitting, and the whole surface error is recovered. Simulation results are shown to demonstrate the feasibility of the method we developed. By analyzing the influence of the six DOF on the stitching result, the most important factor is obtained, and some measures are taken, that is, a measurement system combining two interferometers is designed, one of which is to measure the departures between the reference and the aspheric, and another to test the piston errors to be transmitted to the control system to improve the accuracy.

  11. Design, Construction and Testing of Annular Diffusers for High Speed Civil Transportation Combustor Applications

    Okhio, Cyril B.

    1996-01-01

    A theoretical and an experimental design study of subsonic flow through curved-wall annular diffusers has been initiated under this award in order to establish the most pertinent design parameters and hence performance characteristics for such devices, an the implications of their application in the design of engine components in the aerospace industries. The diffusers under this study are expected to contain appreciable regions of stall and the effects of swirl on their performance are being studied. The experimental work involves the application of Computer Aided Design software tool to the development of a suitable annular diffuse geometry and the subsequent downloading of such data to a CNC machine at Central State University (CSU). Two experimental run segments have been completed so far during FY-95 involving flow visualization and diffuser performance evaluation based on Kinetic Energy Dissipation. The method of calculation of the performance of diffusers based on pressure recovery coefficient has been shown to have some shortcomings and so the kinetic energy dissipation approach has been introduced in the run segment two with some success. The application of the discretized, full Navier Stokes and Continuity equations to the numerical study of the problem described above for the time-mean flow is expected to follow. Various models of turbulence are being evaluated for adoption throughout the study and comparisons would be made with experimental data where they exist. Assessment of diffuser performance based on the dissipated mechanical energy would also be made. The result of the investigations are expected to indicate that more cost effective component design of such devices as diffusers which normally contain complex flows can still be achieved.

  12. Multiple matching scheme for broadband 0.72Pb(Mg(13)Nb(23))O(3)-0.28PbTiO(3) single crystal phased-array transducer.

    Lau, S T; Li, H; Wong, K S; Zhou, Q F; Zhou, D; Li, Y C; Luo, H S; Shung, K K; Dai, J Y

    2009-05-01

    Lead magnesium niobate-lead titanate single crystal 0.72Pb(Mg(13)Nb(23))O(3)-0.28PbTiO(3) (abbreviated as PMN-PT) was used to fabricate high performance ultrasonic phased-array transducer as it exhibited excellent piezoelectric properties. In this paper, we focus on the design and fabrication of a low-loss and wide-band transducer for medical imaging applications. A KLM model based simulation software PiezoCAD was used for acoustic design of the transducer including the front-face matching and backing. The calculated results show that the -6 dB transducer bandwidth can be improved significantly by using double lambda8 matching layers and hard backing. A 4.0 MHz PMN-PT transducer array (with 16 elements) was fabricated and tested in a pulse-echo arrangement. A -6 dB bandwidth of 110% and two-way insertion loss of -46.5 dB were achieved.

  13. Evaporating metal nanocrystal arrays

    Zhang, Xue; Joy, James C.; Zhao, Chenwei; Kim, Jin Ho; Fernandes, Gustavo; Xu, J. M.; Valles, James M., Jr.

    2017-03-01

    Anodic aluminum oxide (AAO) substrates with a self-ordered triangular array of nanopores provide the means to fabricate multiple forms of nano materials, such as nanowires and nanoparticles. This study focuses on nanostructures that emerge in thin films of metals thermally evaporated onto the surface of AAO. Previous work showed that films of different evaporated metals assume dramatically different structures, e.g. an ordered triangular array of nearly monodisperse nanoparticles forms for lead (Pb) while a polycrystalline nanohoneycomb structure forms for silver (Ag). Here, we present investigations of the effects of substrate temperature and deposition angle that reveal the processes controlling the nano particle array formation. Our findings indicate that arrays form provided the grain nucleation density exceeds the pore density and the atomic mobility is high enough to promote grain coalescence. They introduce a method for producing films with anisotropic grain array structure. The results provide insight into the influence of substrate nano-morphology on thin film growth energetics and kinetics that can be harnessed for creating films with other novel nano-structures.

  14. Experimental investigation of gas turbine airfoil aerodynamic performance without and with film cooling in an annular sector cascade

    Wiers, S.H.

    2002-02-01

    The steady growing of industrialization, the densification of the anthroposphere, the increasing concern over the effects of gas turbine cruise emissions on the atmosphere threaten the growth of air transportation, and the perception about the possible climatic impact of CO{sub 2} emissions causes a public distinctive sense of responsibility. The conventional energy production techniques, which are based on fossil fuel, will keep its central importance within the global energy production. Forecasts about the increasing air transportation give duplication in the next 10-15 years. The optimization of the specific fuel consumption is necessary to decrease the running costs and the pollution emissions in the atmosphere, which makes an increased process efficiency of stationary turbines as well as of jet engines essential. This leads to the necessity of an increased thermodynamic efficiency of the overall process and the optimization of the aerodynamic components. Due to the necessity of more detailed three-dimensional data on the behavior of film cooled blades an annular sector cascade turbine test facility has gone into service. The annular sector cascade facility is a relative cost efficient solution compared to a full annular facility to investigate three-dimensional effects on a non cooled and cooled turbine blade. The aerodynamic investigations on the annular sector cascade facility are part of a broad perspective where experimental data from a hot annular sector cascade facility and the cold annular sector facility are used to verify, calibrate and understand the physics for both internal and external calculation methods for flow and heat transfer prediction. The objective of the present study is the design and validation of a cold flow annular sector cascade facility, which meets the flow conditions in a modem turbine as close as possible, with emphasis on achieving periodic flow conditions. The first part of this study gives the necessary background on this

  15. Wireless Josephson Junction Arrays

    Adams, Laura

    2015-03-01

    We report low temperature, microwave transmission measurements on a wireless two- dimensional network of Josephson junction arrays composed of superconductor-insulator -superconductor tunnel junctions. Unlike their biased counterparts, by removing all electrical contacts to the arrays and superfluous microwave components and interconnects in the transmission line, we observe new collective behavior in the transmission spectra. In particular we will show emergent behavior that systematically responds to changes in microwave power at fixed temperature. Likewise we will show the dynamic and collective response of the arrays while tuning the temperature at fixed microwave power. We discuss these spectra in terms of the Berezinskii-Kosterlitz-Thouless phase transition and Shapiro steps. We gratefully acknowledge the support Prof. Steven Anlage at the University of Maryland and Prof. Allen Goldman at the University of Minnesota. Physics and School of Engineering and Applied Sciences.

  16. The Submillimeter Array

    Ho, P T P; Lo, K Y; Ho, Paul T.P.; Moran, James M.; Lo, Kwok Yung

    2004-01-01

    The Submillimeter Array (SMA), a collaborative project of the Smithsonian Astrophysical Observatory (SAO) and the Academia Sinica Institute of Astronomy and Astrophysics (ASIAA), has begun operation on Mauna Kea in Hawaii. A total of eight 6-m telescopes comprise the array, which will cover the frequency range of 180-900 GHz. All eight telescopes have been deployed and are operational. First scientific results utilizing the three receiver bands at 230, 345, and 690 GHz have been obtained and are presented in the accompanying papers.

  17. Photovoltaic array performance model.

    Kratochvil, Jay A.; Boyson, William Earl; King, David L.

    2004-08-01

    This document summarizes the equations and applications associated with the photovoltaic array performance model developed at Sandia National Laboratories over the last twelve years. Electrical, thermal, and optical characteristics for photovoltaic modules are included in the model, and the model is designed to use hourly solar resource and meteorological data. The versatility and accuracy of the model has been validated for flat-plate modules (all technologies) and for concentrator modules, as well as for large arrays of modules. Applications include system design and sizing, 'translation' of field performance measurements to standard reporting conditions, system performance optimization, and real-time comparison of measured versus expected system performance.

  18. Selecting Sums in Arrays

    Brodal, Gerth Stølting; Jørgensen, Allan Grønlund

    2008-01-01

    In an array of n numbers each of the \\binomn2+nUnknown control sequence '\\binom' contiguous subarrays define a sum. In this paper we focus on algorithms for selecting and reporting maximal sums from an array of numbers. First, we consider the problem of reporting k subarrays inducing the k larges...... an algorithm with this running time and by proving a matching lower bound. Finally, we combine the ideas and obtain an O(n· max {1,log(k/n)}) time algorithm that selects a subarray storing the k’th largest sum among all subarrays of length at least l and at most u....

  19. Particle-in-cell simulation of electron trajectories and irradiation uniformity in an annular cathode high current pulsed electron beam source

    Jiang, Wei; Wang, Langping; Zhou, Guangxue; Wang, Xiaofeng

    2017-02-01

    In order to study electron trajectories in an annular cathode high current pulsed electron beam (HCPEB) source based on carbon fiber bunches, the transmission process of electrons emitted from the annular cathode was simulated using a particle-in-cell model with Monte Carlo collisions (PIC-MCC). The simulation results show that the intense flow of the electrons emitted from the annular cathode are expanded during the transmission process, and the uniformity of the electron distribution is improved in the transportation process. The irradiation current decreases with the irradiation distance and the pressure, and increases with the negative voltage. In addition, when the irradiation distance and the cathode voltage are larger than 40 mm and -15 kV, respectively, a uniform irradiation current distribution along the circumference of the anode can be obtained. The simulation results show that good irradiation uniformity of circular components can be achieved by this annular cathode HCPEB source.

  20. TRMM Solar Array Panels

    1998-01-01

    This final report presents conclusions/recommendations concerning the TRMM Solar Array; deliverable list and schedule summary; waivers and deviations; as-shipped performance data, including flight panel verification matrix, panel output detail, shadow test summary, humidity test summary, reverse bias test panel; and finally, quality assurance summary.

  1. TANGO Array.. 2. Simulations

    Bauleo, P.; Bonifazi, C.; Filevich, A.

    2004-01-01

    The angular and energy resolutions of the TANGO Array were obtained using extensive Monte Carlo simulations performed with a double purpose: (1) to determine the appropriate parameters for the array fitting to the desired range of sensitivity (the knee energy region), and (2) to construct a reliable shower database required for reference in the analysis of experimental data. The AIRES code, with the SIBYLL hadronic collision package, was used to simulate Extended Air Showers produced by primary cosmic rays (assuming protons and iron nuclei), with energies ranging from 10 14 to 10 18 eV. These data were fed into a realistic code which simulates the response of the detectors (water Cherenkov detectors), including the electronics, pickup noise, and the signal attenuation in the connecting cables. The trigger stage was considered in the simulations in order to estimate the trigger efficiency of the array and to verify the accuracy of the reconstruction codes. This paper delineates the simulations performed to obtain the expected behavior of the array, and describes the simulated data. The results of these simulations suggest that we can expect an error in the energy of the primary cosmic-ray of ˜60% of the estimated value and that the error in the measurement of the direction of arrival can be estimated as ˜4°. The present simulations also indicate that unambiguous assignments of the primary energy cannot be obtained because of the uncertainty in the nature of the primary cosmic ray.

  2. TANGO Array. 2. Simulations

    Bauleo, P. E-mail: pablo.bauleo@colostate.edu; Bonifazi, C.; Filevich, A

    2004-01-11

    The angular and energy resolutions of the TANGO Array were obtained using extensive Monte Carlo simulations performed with a double purpose: (1) to determine the appropriate parameters for the array fitting to the desired range of sensitivity (the knee energy region), and (2) to construct a reliable shower database required for reference in the analysis of experimental data. The AIRES code, with the SIBYLL hadronic collision package, was used to simulate Extended Air Showers produced by primary cosmic rays (assuming protons and iron nuclei), with energies ranging from 10{sup 14} to 10{sup 18} eV. These data were fed into a realistic code which simulates the response of the detectors (water Cherenkov detectors), including the electronics, pickup noise, and the signal attenuation in the connecting cables. The trigger stage was considered in the simulations in order to estimate the trigger efficiency of the array and to verify the accuracy of the reconstruction codes. This paper delineates the simulations performed to obtain the expected behavior of the array, and describes the simulated data. The results of these simulations suggest that we can expect an error in the energy of the primary cosmic-ray of {approx}60% of the estimated value and that the error in the measurement of the direction of arrival can be estimated as {approx}4 deg. . The present simulations also indicate that unambiguous assignments of the primary energy cannot be obtained because of the uncertainty in the nature of the primary cosmic ray.

  3. The Murchison Widefield Array

    Mitchell, Daniel A.; Greenhill, Lincoln J.; Ord, Stephen M.; Bernardi, Gianni

    2010-01-01

    It is shown that the excellent Murchison Radio-astronomy Observatory site allows the Murchison Widefield Array to employ a simple RFI blanking scheme and still calibrate visibilities and form images in the FM radio band. The techniques described are running autonomously in our calibration and imagin

  4. Array processors in chemistry

    Ostlund, N.S.

    1980-01-01

    The field of attached scientific processors (''array processors'') is surveyed, and an attempt is made to indicate their present and possible future use in computational chemistry. The current commercial products from Floating Point Systems, Inc., Datawest Corporation, and CSP, Inc. are discussed.

  5. Bandwidth Reconfigurable Metamaterial Arrays

    Nathanael J. Smith

    2014-01-01

    Full Text Available Metamaterial structures provide innovative ways to manipulate electromagnetic wave responses to realize new applications. This paper presents a conformal wideband metamaterial array that achieves as much as 10 : 1 continuous bandwidth. This was done by using interelement coupling to concurrently achieve significant wave slow-down and cancel the inductance stemming from the ground plane. The corresponding equivalent circuit of the resulting array is the same as that of classic metamaterial structures. In this paper, we present a wideband Marchand-type balun with validation measurements demonstrating the metamaterial (MTM array’s bandwidth from 280 MHz to 2800 MHz. Bandwidth reconfiguration of this class of array is then demonstrated achieving a variety of band-pass or band-rejection responses within its original bandwidth. In contrast with previous bandwidth and frequency response reconfigurations, our approach does not change the aperture’s or ground plane’s geometry, nor does it introduce external filtering structures. Instead, the new responses are realized by making simple circuit changes into the balanced feed integrated with the wideband MTM array. A variety of circuit changes can be employed using MEMS switches or variable lumped loads within the feed and 5 example band-pass and band-rejection responses are presented. These demonstrate the potential of the MTM array’s reconfiguration to address a variety of responses.

  6. Microelectronic Stimulator Array

    2000-08-09

    retinal prosthesis test device. Figure 3b shows an enlarged view of a nano-channel glass (NCG) electrode array. Figure 4 shows a conceptual layout (floor...against a visual cortex. 10 This involves invasive brain surgery through the cranium . From a surgical point of view, the intra ocular approach is

  7. Visualization of the boiling phenomena and counter-current flow limit of annular heat pipe

    Kim, In Guk; Kim, Kyung Mo; Jeong, Yeong Shin; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of)

    2015-10-15

    The thermal resistance of conventional heat pipes increases over the capillary limit because of the insufficient supplement of the working fluid. Due to the shortage of the liquid supplement, thermosyphon is widely used for vertically oriented heat transport and high heat load conditions. Thermosyphons are two-phase heat transfer devices that have the highly efficient heat transport from evaporation to condensation section that makes an upward driving force for vapor. In the condenser section, the vapor condenses and releases the latent heat. Due to the gravitation force acting on the liquid in the tube, working fluid back to the evaporator section, normally this process operate at the vertical and inclination position. The use of two-phase closed thermosyphon (TPCT) for the cooling devices has the limitation due to the phase change of the working fluid assisted by gravity force. Due to the complex phenomenon of two-phase flow, it is required to understand what happened in TPCT. The visualization of the thermosyphon and heat pipe is investigated for the decrease of thermal resistance and enhancement of operation limit. Weibel et al. investigated capillary-fed boiling of water with porous sintered powder wick structure using high speed camera. At the high heat flux condition, dry-out phenomenon and a thin liquid film are observed at the porous wick structure. Wong and Kao investigated the evaporation and boiling process of mesh wicked heat pipe using optical camera. At the high heat flux condition, the water filing became thin and partial dry-out was observed in the evaporator section. Our group suggested the concept of a hybrid heat pipe with control rod as Passive IN-core Cooling System (PINCs) for decay heat removal for advanced nuclear power plant. The hybrid heat pipe is the combination of the heat pipe and control rod. It is necessary for PINCs to contain a neutron absorber (B{sub 4}C) to have the ability of reactivity control. It has annular vapor space and

  8. Comparison of the Characteristics of Solid Type and Annular Type Nuclear Fuels Using Thermoelastic-Plastic-Creep FEM

    Young-Doo Kwon

    2016-01-01

    Full Text Available The purpose of this study is to compare the characteristics of two types of nuclear fuel using the finite element program of thermoelastic-plastic-creep analysis. The analyzed fuel rods are of two types, solid and annular ones, and their thermomechanical characteristics are compared. Thermoelastic-plastic-creep analyses were made using an in-house finite element analysis program that adopts the “effective-stress-function” algorithm. The temperature-dependent material properties, which were obtained from the experiments for actual nuclear reactors, are adopted. The effects of type of fuel systems are revealed in both stresses and temperature distributions. The maximum tensile and compressive hoop stress of pellet and cladding are monitored to evaluate the mechanical behavior, and the maximum temperature is used to evaluate the thermal behavior. Although the annular type of fuel has certain disadvantage, it would be used very effectively or safely in future nuclear power plants.

  9. Comparison of thermal and hydraulic performances of eccentric and concentric annular-fins of heat exchanger tubes

    Benmachiche, Abdelmoumène Hakim; Tahrour, Farouk; Aissaoui, Faris; Aksas, Mounir; Bougriou, Cherif

    2017-02-01

    The present study is an experimental and 3-D computational fluid dynamics. It is used to compare between the heat transfer characteristics and pressure drops of eccentric and concentric annular-finned tube bundles. The RNG k-ɛ turbulence model of fluent is used to determine the optimum tube position in the circular fin that gives the highest thermal and hydraulic performances for both staggered and aligned arrangements. Then, experiments and numerical simulations were performed to examine the effects of bundle configurations, the Reynolds number (ranging from 5500 to 29,700) and the tube location inside the heat exchangers. A satisfactory qualitative and quantitative agreement was obtained between the numerical and experimental results. For both aligned and staggered heat exchangers, the thermal characteristics of the eccentric annular-finned tube are greater than that of the concentric ones. This gain is associated with reduction in pressure drop.

  10. Exact solutions for the flow of non-Newtonian fluid with fractional derivative in an annular pipe

    TONG Dengke; WANG Ruihe; YANG Heshan

    2005-01-01

    This paper deals with some unsteady unidirectional transient flows of Oldroyd-B fluid in an annular pipe. The fractional calculus approach in the constitutive relationship model Oldroyd-B fluid is introduced and a generalized Jeffreys model with the fractional calculus has been built. Exact solutions of some unsteady flows of Oldroyd-B fluid in an annular pipe are obtained by using Hankel transform and Laplace transform for fractional calculus. The following four problems have been studied: (1) Poiseuille flow due to a constant pressure gradient; (2) axial Couette flow in an annulus; (3) axial Couette flow in an annulus due to a longitudinal constant shear; (4) Poiseuille flow due to a constant pressure gradient and a longitudinal constant shear. The well-known solutions for Navier-Stokes fluid, as well as those corresponding to a Maxwell fluid and a second grade one, appear as limited cases of our solutions.

  11. Three-dimensional direct numerical simulations of co/counter-current vertical gas-Liquid annular flows

    Farhaoui, Asma; Kahouadji, Lyes; Chergui, Jalel; Juric, Damir; Shin, Seungwon; Craster, Richard; Matar, Omar

    2016-11-01

    We carry out three-dimensional numerical simulations of co/counter current Gas-Liquid annular flows using the parallel code, BLUE, based on a projection method for the resolution of the Navier-Stokes equations and a hybrid Front-Tracking/Level-Set method for the interface advection. Gas-Liquid annular flows and falling films in a pipe are present in a broad range of industrial processes. This configuration consists of an important multiphase flow regime where the liquid occupies the area adjacent to the internal circumference of the pipe and the gas flows in the pipe core. Experimentally, four distinctive flow regimes were identified ('dual-wave', 'thick ripple', 'disturbance wave' and 'regular wave' regimes), that we attempt to simulate. In order to visualize these different regimes, various liquid (water) and gas (air) flow-rates are investigated. EPSRC UK Programme Grant EP/K003976/1.

  12. Exact solutions for the flow of non-Newtonian fluid with fractional derivative in an annular pipe

    Tong, Dengke; Wang, Ruihe; Yang, Heshan

    2005-08-01

    This paper deals with some unsteady unidirectional transient flows of Oldroyd-B fluid in an annular pipe. The fractional calculus approach in the constitutive relationship model Oldroyd-B fluid is introduced and a generalized Jeffreys model with the fractional calculus has been built. Exact solutions of some unsteady flows of Oldroyd-B fluid in an annular pipe are obtained by using Hankel transform and Laplace transform for fractional calculus. The following four problems have been studied: (1) Poiseuille flow due to a constant pressure gradient; (2) axial Couette flow in an annulus; (3) axial Couette flow in an annulus due to a longitudinal constant shear; (4) Poiseuille flow due to a constant pressure gradient and a longitudinal constant shear. The well-known solutions for Navier-Stokes fluid, as well as those corresponding to a Maxwell fluid and a second grade one, appear as limited cases of our solutions.

  13. Large-scale culture of a tropical marine microalga Chaetoceros calcitrans (Paulsen) Takano 1968 at different temperatures using annular photobioreactors.

    Lai, J I; Yusoff, F M; Shariff, M

    2012-07-01

    Outdoor mass culture of microalgae in the tropical area is important to minimize its production cost. This study evaluates the growth of Chaetoceros calcitrans in 120 L annular photobioreactors at indoor temperature (Treatment I, 25 +/- 2 degrees C) and outdoor tropical ambient temperature, (Treatment II, 30 +/- 6 degrees C). Each treatment was done in duplicates. For both treatments, C. calcitrans was first grown in starter columns of 10 L capacity for a period of 7 days at 25 +/- 2 degrees C. After 7 days, the 9 L culture was transferred to the annular photobioreactors and subsequently brought to a final volume of 100 L by adding 20 L fresh medium every 5 days. There was no significant difference (p > 0.05) in the dry weight of microalgae grown in natural light and those grown indoor. The results suggest that C. calcitrans can be grown in outdoor conditions, hence, saving time and microalgae production cost for the larviculture industry.

  14. Medial arterial calcification, calcific aortic stenosis and mitral annular calcification in a diabetic patient with severe autonomic neuropathy.

    Cronin, C C

    2012-02-03

    Medial arterial calcification (Monckeberg\\'s arteriosclerosis) is well described in diabetic patients with autonomic neuropathy. There is also a high prevalence of diabetes mellitus among subjects with calcific aortic stenosis and mitral annular calcification. We describe a diabetic patient with autonomic neuropathy and extensive medial arterial calcification who also had calcification of the aortic valve and of the mitral valve annulus. We propose that autonomic neuropathy may play a role in calcification of these structures at the base of the heart.

  15. A PCM/forced convection conjugate transient analysis of energy storage systems with annular and countercurrent flows

    Cao, Y.; Faghri, A.; Juhasz, A.

    1991-01-01

    Latent heat energy storage systems with both annular and countercurrent flows are modeled numerically. The change of phase of the phase-change material (PCM) and the transient forced convective heat transfer for the transfer fluid are solved simultaneously as a conjugate problem. A parametric study and a system optimization are conducted. It is found that the energy storage system with the countercurrent flow is an efficient way to absorb heat energy in a short period for pulsed power load space applications.

  16. Quantifying the eddy-jet feedback strength of the annular mode in an idealized GCM and reanalysis data

    Ma, Ding; Kuang, Zhiming

    2016-01-01

    A linear response function (LRF) that relates the temporal tendency of zonal mean temperature and zonal wind to their anomalies and external forcing is used to accurately quantify the strength of the eddy-jet feedback associated with the annular mode in an idealized GCM. Following a simple feedback model, the results confirm the presence of a positive eddy-jet feedback in the annular mode dynamics, with a feedback strength of 0.137 day$^{-1}$ in the idealized GCM. Statistical methods proposed by earlier studies to quantify the feedback strength are evaluated against results from the LRF. It is argued that the mean-state-independent eddy forcing reduces the accuracy of these statistical methods because of the quasi-oscillatory nature of the eddy forcing. A new method is proposed to approximate the feedback strength as the regression coefficient of low-pass filtered eddy forcing onto low-pass filtered annular mode index, which converges to the value produced by the LRF when timescales longer than 200 days are u...

  17. PRESSURE AND VELOCITY AMPLITUDES OF THE INCOMPRESSIBLE FLUID IN CONCENTRIC ANNULAR PASSAGE WITH OSCILLATORY BOUNDARY: TURBULENT FLOW

    ABOLGHASEM MEKANIK

    2014-04-01

    Full Text Available An unsteady program based on a turbulence model called Baseline (BSL komega model was conducted to simulate three turbulent flows with Re numbers of 4×103, 8×103 and 1×104, between two initially concentric cylinders. The effects of principal flow variables, i.e., mean axial velocity and fluid temperature, annular passage configurations, i.e., the gap width and radii of cylinders on the pressure and circumferential velocity of a three dimensional turbulent flow in the annular passage were investigated. The results were validated with the available solutions in the literature and fairly good agreements are seen. By increasing the gap of the annular passage and the axial flow velocity, smaller values for the unsteady pressure and the circumferential velocity amplitudes are produced. For each of the turbulent flows the unsteady pressure amplitude increases with the fluid temperature, as well as the circumferential velocity amplitude. The results of this investigation are favorably used for FIV and FSI calculations in such configurations.

  18. Acoustic radiation from out-of-plane modes of an annular disk using thin and thick plate theories

    Lee, Hyeongill; Singh, Rajendra

    2005-04-01

    Out-of-plane (flexural) vibration is a major source of sound radiation from many mechanical or structural components having annular or circular disk shape. The typical thickness of practical components is often beyond the thin plate theory limit and it may have considerable effect on sound radiation. But, traditionally, thin annular disk models have been employed for such structures neglecting the thickness effect. In this article, structural eigensolutions for the out-of-plane modes and sound radiation from the modal vibration of a thick annular disk with free-free boundaries have been calculated using both thick and thin plate theories. A new analytical formulation is proposed for the sound radiation problem. In addition, the same problem has been solved by a semi-analytical procedure in which the disk surface velocity is numerically defined by a finite-element model and sound radiation is then analytically obtained using a modified circular radiator model. Also, the effects of radii and thickness ratios on the structural and acoustic radiation characteristics are investigated using the analytical procedure. Finally, the effect of boundary conditions is briefly examined.

  19. Study of downward annular pipe flow using combined laser-based approaches

    An, Jae Sik; Cherdantsev, Andrey; Zadrazil, Ivan; Matar, Omar; Markides, Christos

    2016-11-01

    In downward annular flow, the liquid phase flows as a film along the pipe wall and the gas flows in the core of the pipe. The liquid free-surface is covered by a complex multiscale system of waves. The interaction dynamics of the interfacial waves with each other and with the gas stream exert a significant influence on the pressure drop, heat transfer and mass interchange between the phases. The complexity of the interface requires the application of measurement techniques with high spatiotemporal resolution. In this work, two approaches based on the principle of laser-induced fluorescence, namely planar LIF and brightness-based LIF, are applied simultaneously to study interfacial phenomena in these flows, while simultaneous LIF and PIV are used to obtain velocity field information in the liquid phase underneath the waves. Sources of measurement bias are then analysed: total internal reflection at the out-of-plane interface; steep longitudinal slopes and transverse wave curvature; presence of gas bubbles in the liquid film. Although each method has its own limitations, a combined technique can provide reliable spatiotemporal measurements of film thickness to accompany the velocity information. Finally, flow development is studied in a moving frame of reference over long lengths. EPSRC UK Programme Grant MEMPHIS (EP/K003976/1).

  20. Heat Transfer and hydrodynamics in Annular Chromatography:CFD—Simulation and Experiments

    Hans-JoergBart; JorgBrozio; 等

    2000-01-01

    Continuous annular chromatography(CAC) is a separation process for multicomponent liquid mixtures.The performance of the apparatus can be seriously decreased by temperature gradients inside the adsorbent bed.It is shown.that the temperature gradients can be significantly reduced by a pre-heating of the entering liquid in the apparatus itself.Heat transfer and hydrodynamics in the porous media are described by two different modlelling approaches.Both are based on a pseudo-homogeneous model for heat transfer with temperature dependent fluid viscosities,The first model considers one-dimensional fiud flow and two-dimensional heat transfer,The second,ore rigorous one is a three-dimensional model for heat transfer and hydrodynamics.The simulation results obtained with both models are in good agreement with experimental results.The experiments have been performed with glass beads as the stationary phase and water as the liquid phase under different boundary conditions.The temparature profiles inside the packed bed have been measured with thermocouples.

  1. Educational, scientific, tourist and outreach potential of the September 1, 2016 Annular Solar Eclipse in Tanzania

    Tayabali Jiwaji, Noorali

    2015-08-01

    Tanzania will witness a major astronomical spectacle of an annular eclipse on September 1, 2016. The central part of the eclipse will pass through southern Tanzania, crossing national parks and game reserves such as Katavi and the world famous Selous. For the rest of Tanzania and neighbouring countries it will be a memorable event with large of the proportion of the Sun being covered up. The climate in Tanzania during September is cool and dry which will provide ideal viewing conditions. Solar eclipse events attract "eclipse chasers" from around the globe.Scientific interest in measuring the properties of the Sun and the effects of the eclipse on the atmosphere will allow local scientists to partner with leading scientists to gain valuable experience and knowledge.Local population's wonder and interest in eclipses can be exploited through public-private partnerships by encouraging students and local people to travel to the central path or to observe from their backyards. Large number of eclipse glasses can be manufactured cheaply using safe solar filters for supplying to students and general population in Tanzania and neigbouring countries. This will raise science awareness about the wonders of our Universe.When combined with the attraction of Tanzania's treasures in the north and the 16 tonne Mbozi meteorite in southern Tanzania, the touristic potential of this event can be exploited through tour packages and worldwide advertisements during the coming year.

  2. Laser anemometer measurements and computations in an annular cascade of high turning core turbine vanes

    Goldman, Louis J.; Seasholtz, Richard G.

    1992-01-01

    An advanced laser anemometer (LA) was used to measure the axial and tangential velocity components in an annular cascade of turbine stator vanes designed for a high bypass ratio engine. These vanes were based on a redesign of the first-stage stator, of a two-stage turbine, that produced 75 degrees of flow turning. Tests were conducted on a 0.771 scale model of the engine size stator. The advanced LA fringe system was designed to employ thinner than usual laser beams resulting in a 50-micron-diameter probe volume. Window correction optics were used to ensure that the laser beams did not uncross in passing through the curved optical access port. Experimental LA measurements of velocity and turbulence were obtained both upstream, within, and downstream of the stator vane row at the design exit critical velocity ratio of 0.896 at the hub. Static pressures were also measured on the vane surface. The measurements are compared, where possible with calculations from a 3-D inviscid flow analysis. The data are presented in both graphic and tabulated form so that they may be readily used to compare against other turbomachinery computations.

  3. Non-annular, hemispheric signature of the winter North Atlantic Oscillation

    García-Serrano, J.; Haarsma, R. J.

    2016-07-01

    Sensitivity experiments with an atmospheric general circulation model (AGCM) without a proper stratosphere are performed to locally force a North Atlantic oscillation (NAO)-like response in order to analyse the tropospheric dynamics involved in its hemispheric extent. Results show that the circulation anomalies are not confined to the North Atlantic basin not even within the first 10 days of integration, where the atmospheric response propagates downstream into the westerly jets. At this linear stage, transient-eddy activity dominates the emerging, regional NAO-like pattern while zonal-eddy coupling may add on top of the wave energy propagation. Later at the quasi-equilibrium nonlinear stage, the atmospheric response emphasizes a wavenumber-5 structure embedded in the westerly jets, associated with transient-eddy feedback upon the Atlantic and Pacific storm-tracks. This AGCM waveguided structure rightly projects on the observational NAO-related circumglobal pattern, providing evidence of its non-annular character in the troposphere. These findings support the view on the importance of the circumglobal waveguide pattern on the development of NAO-related anomalies at hemispheric level. It could help to settle a consensus view of the Arctic Oscillation, which has been elusive so far.

  4. Electrically driven convection in a thin annular film undergoing Couette flow

    Daya, Z A; Morris, S W; Daya, Zahir A.; Morris, Stephen W.

    1998-01-01

    We investigate the linear stability of a thin, suspended, annular film of conducting fluid with a voltage difference applied between its inner and outer edges. For a sufficiently large voltage, such a film is unstable to radially-driven electroconvection due to charges which develop on its free surfaces. The film can also be subjected to a Couette shear by rotating its inner edge. This combination is experimentally realized using films of smectic A liquid crystals. In the absence of shear, the convective flow consists of a stationary, azimuthally one-dimensional pattern of symmetric, counter-rotating vortex pairs. When Couette flow is applied, an azimuthally traveling pattern results. When viewed in a co-rotating frame, the traveling pattern consists of pairs of asymmetric vortices. We calculate the neutral stability boundary for arbitrary radius ratio $\\alpha$ and Reynolds number ${R e}$ of the shear flow, and obtain the critical control parameter $R_c (\\alpha, {R e})$ and the critical azimuthal mode number ...

  5. Investigations of the torque anomaly in an annular sector. II. Global calculations, electromagnetic case

    Milton, Kimball A; Abalo, E K; Kheirandish, Fardin; Kirsten, Klaus

    2013-01-01

    Recently, it was suggested that there was some sort of breakdown of quantum field theory in the presence of boundaries, manifesting itself as a torque anomaly. In particular, Fulling et al. used the finite energy-momentum-stress tensor in the presence of a perfectly conducting wedge, calculated many years ago by Deutsch and Candelas, to compute the torque on one of the wedge boundaries, where the latter was cutoff by integrating the torque density down to minimum lower radius greater than zero. They observed that that torque is not equal to the negative derivative of the energy obtained by integrating the energy density down to the same minimum radius. This motivated a calculation of the torque and energy in an annular sector obtained by the intersection of the wedge with two coaxial cylinders. In a previous paper we showed that for the analogous scalar case, which also exhibited a torque anomaly in the absence of the cylindrical boundaries, the point-split regulated torque and energy indeed exhibit an anomal...

  6. Investigation into adsorption and photocatalytic degradation of gaseous benzene in an annular fluidized bed photocatalytic reactor.

    Geng, Qijin; Tang, Shankang; Wang, Lintong; Zhang, Yunchen

    2015-01-01

    The adsorption and photocatalytic degradation of gaseous benzene were investigated considering the operating variables and kinetic mechanism using nano-titania agglomerates in an annular fluidized bed photocatalytic reactor (AFBPR) designed. The special adsorption equilibrium constant, adsorption active sites, and apparent reaction rate coefficient of benzene were determined by linear regression analysis at various gas velocities and relative humidities (RH). Based on a series of photocatalytic degradation kinetic equations, the influences of operating variables on degradation efficiency, apparent reaction rate coefficient and half-life were explored. The findings indicated that the operating variables have obviously influenced the adsorption/photocatalytic degradation and corresponding kinetic parameters. In the photocatalytic degradation process, the relationship between photocatalytic degradation efficiency and RH indicated that water molecules have a dual-function which was related to the structure characteristics of benzene. The optimal operating conditions for photocatalytic degradation of gaseous benzene in AFBPR were determined as the fluidization number at 1.9 and RH required related to benzene concentration. This investigation highlights the importance of controlling RH and benzene concentration in order to obtain the desired synergy effect in photocatalytic degradation processes.

  7. Annularly grooved membrane combined with rood beam piezoresistive pressure sensor for low pressure applications

    Li, Chuang; Cordovilla, Francisco; Ocaña, José L.

    2017-03-01

    A novel structural piezoresistive pressure sensor with annularly grooved membrane combined with rood beam has been proposed for low pressure measurements based on silicon substrate. In this study, a design method, including the model design, dimensions optimization, and performance prediction of the novel structure sensor, is presented. The finite element method has been used to analyze the stress distribution of sensitive elements and the deflection of membrane. On the basis of simulation results, the relationships between structural dimension variables and mechanical performance are deduced, which make the fabrication processes more efficient. According to statistics theory, the coefficient of determination R2 and residual sum of squares are introduced to indicate whether the fitting equations and curves match well with the simulation results. After that, a series of the optimal membrane dimensions are determined. Compared with other structural sensors, the optimized sensor achieves the best overall properties as it mitigates the contradiction between sensitivity and linearity. The reasons why the proposed sensor can maximize sensitivity and minimize nonlinearity are also discussed. By localizing more strain energy in the high concentrated stress profile and creating partially stiffened membrane, the proposed sensor has achieved a high sensitivity of 34.5 (mV/V)/psi and a low nonlinearity of 0.25% FSS. Thus, the proposed structure sensor will be a proper choice for low pressure applications less than 1 psi.

  8. Performance Testing of a Prototypic Annular Linear Induction Pump for Fission Surface Power

    Polzin, K. A.; Pearson, J. B.; Schoenfeld, M. P.; Webster, K.; Houts, M. G.; Godfroy, T. J.; Bossard, J. A.

    2010-01-01

    Results of performance testing of an annular linear induction pump are presented. The pump electromagnetically pumps liquid metal (NaK) through a circuit specially designed to allow for quantification of the performance. Testing was conducted over a range of conditions, including frequencies of 33, 36, 39, and 60 Hz, liquid metal temperatures from 25 to 525 C, and input voltages from 5 to 120 V. Pump performance spanned a range of flow rates from roughly 0.16 to 5.7 L/s (2.5 to 90 gpm), and pressure head <1 to 90 kPa (<0.145 to 13 psi). The maximum efficiency measured during testing was slightly greater than 6%. The efficiency was fairly insensitive to input frequency from 33 to 39 Hz, and was markedly lower at 60 Hz. In addition, the efficiency decreased as the NaK temperature was raised. While the pump was powered, the fluid responded immediately to changes in the input power level, but when power was removed altogether, there was a brief slow-down period before the fluid would come to rest. The performance of the pump operating on a variable frequency drive providing 60 Hz power compared favorably with the same pump operating on 60 Hz power drawn directly from the electrical grid.

  9. Electrohydrodynamic instability in an annular liquid layer with radial conductivity gradients.

    Ding, Zijing; Wong, Teck Neng

    2014-03-01

    In this paper, the electrohydrodynamic stability in an annular liquid layer with a radial electrical conductivity gradient is investigated. A weak shear flow arises from a constant pressure gradient in the axial direction. In the radial direction, an electric field is applied. The three-dimensional linear instability analysis is implemented to study the influence of the inner radius, electrical conductivity gradient, shear flow, and ionic diffusion on the dynamics of the fluid layer. It is found that the critical unstable mode may either be oscillatory or stationary. The system becomes more unstable as the dimensionless inner radius a increases. When the inner radius a is small, the critical unstable mode is stationary, while it is given by three-dimensional oblique waves when a is large. When the conductivity gradient is small, the critical unstable mode is the three-dimensional oblique wave, while when the conductivity gradient is large, it would switch to the stationary mode rather than the oscillatory mode. The system becomes more unstable when the Reynolds number is slightly increased from zero. Additionally, it is found that the electrical Schmidt number has dual effects. The liquid layer becomes either more unstable or stable as the electric Schmidt number increases.

  10. Vibrational mode and sound radiation of electrostatic speakers using circular and annular diaphragms

    Huang, Yu-Hsi; Chiang, Hsin-Yuan

    2016-06-01

    This study modeled two diaphragms comprising a pair of indium tin oxide (ITO) transparent plates sandwiching a vibrating diaphragm to create circular (30 mm radius) and annular (30 mm outer and 3 mm inner radius) push-pull electrostatic speakers. We then measured the displacement amplitudes and mode shapes produced by the devices. Vibration characteristics were used to predict sound pressure levels (SPLs) using the lumped parameter method (LPM) and distributed parameter method (DPM). The two measurement results obtained using a laser system were compared to the SPLs obtained using traditional acoustic measurement (AM) from 20 Hz to 20 kHz in order to verify our predictions. When using LPM and DPM, the SPL prediction results in the first three symmetric modes were in good agreement with the AM results. Under the assumption of linear operations, the DPM and amplitude-fluctuation electronic speckle pattern interferometry (ESPI) techniques proved effective in determining the visualization of mode shape (0,1)-(0,3). The use of ITO plates is a practical technique for the prediction of SPL, as well as measurement of mode shapes. The four evaluation methods, i.e. LPM, DPM, ESPI and AM, present a high degree of consistency with regard to vibrational mode and sound radiation characteristics.

  11. Performance of an Annular Linear Induction Pump with Applications to Space Nuclear Power Systems

    Polzin, Kurt A.; Schoenfeld, Michael; Pearson, J. Boise; Webster, Kenneth; Godfroy, Thomas; Adkins, Harold E., Jr.; Werner, James E.

    2010-01-01

    Results of performance testing of an annular linear induction pump are presented. The pump electromagnetically pumps liquid metal through a circuit specially designed to allow for quantification of the performance. Testing was conducted over a range of conditions, including frequencies of 33, 36, 39, and 60 Hz, liquid metal temperatures from 125 to 525 C, and input voltages from 5 to 120 V. Pump performance spanned a range of flow rates from roughly 0.16 to 5.7 L/s (2.5 to 90 gpm), and pressure head less than 1 to 90 kPa (less than 0.145 to 13 psi). The maximum efficiency measured during testing was slightly greater than 6%. The efficiency was fairly insensitive to input frequency from 33 to 39 Hz, and was markedly lower at 60 Hz. In addition, the efficiency decreased as the NaK temperature was raised. The performance of the pump operating on a variable frequency drive providing 60 Hz power compared favorably with the same pump operating on 60 Hz power drawn directly from the electrical grid.

  12. Engineering double-well potentials with variable-width annular Josephson tunnel junctions

    Monaco, Roberto

    2016-11-01

    Long Josephson tunnel junctions are non-linear transmission lines that allow propagation of current vortices (fluxons) and electromagnetic waves and are used in various applications within superconductive electronics. Recently, the Josephson vortex has been proposed as a new superconducting qubit. We describe a simple method to create a double-well potential for an individual fluxon trapped in a long elliptic annular Josephson tunnel junction characterized by an intrinsic non-uniform width. The distance between the potential wells and the height of the inter-well potential barrier are controlled by the strength of an in-plane magnetic field. The manipulation of the vortex states can be achieved by applying a proper current ramp across the junction. The read-out of the state is accomplished by measuring the vortex depinning current in a small magnetic field. An accurate one-dimensional sine-Gordon model for this strongly non-linear system is presented, from which we calculate the position-dependent fluxon rest-mass, its Hamiltonian density and the corresponding trajectories in the phase space. We examine the dependence of the potential properties on the annulus eccentricity and its electrical parameters and address the requirements for observing quantum-mechanical effects, as discrete energy levels and tunneling, in this two-state system.

  13. Design of Annular Linear Induction Pump for High Temperature Liquid Lead Transportation

    Kwak, Jae Sik; Kim, Hee Reyoung [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

    2014-05-15

    EM(Electro Magnetic) Pump is divided into two parts, which consisted of the primary one with electromagnetic core and exciting coils, and secondary one with liquid lead flow. The main geometrical variables of the pump included core length, inner diameter and flow gap while the electromagnetic ones covered pole pitch, turns of coil, number of pole pairs, input current and input frequency. The characteristics of design variables are analyzed by electrical equivalent circuit method taking into account hydraulic head loss in the narrow annular channel of the ALIP. The design program, which was composed by using MATLAB language, was developed to draw pump design variables according to input requirements of the flow rate, developing pressure and operation temperature from the analyses. The analysis on the design of ALIP for high temperature liquid lead transportation was carried for the produce of ALIP designing program based on MATLAB. By the using of ALIP designing program, we don't have to bother about geometrical relationship between each component during detail designing process because code calculate automatically. And prediction of outputs about designing pump can be done easily before manufacturing. By running the code, we also observe and analysis change of outputs caused by changing of pump factors. It will be helpful for the research about optimization of pump outputs.

  14. Tricuspid Annular Plane Systolic Excursion pada Bayi Kurang Bulan dan Cukup Bulan

    Sri Endah Rahayuningsih

    2011-12-01

    Full Text Available A preterm infant is a baby born with gestational age less than 37 weeks. Preterm babies tend to have problems compared to normal ones. Premature gestational age might result in immaturity of all organ systems of the body including cardiovascular organs. The aim of this study was to find out the right ventricle function by tricuspid annular plane systolic excursion (TAPSE and left ventricle by ejection fraction and shortening fraction using echocardiography on preterm babies. The subject of this study were term and preterm babies who fulfilled the inclusion criteria: appropiate gestational age babies 3–30 days old. This was an analytic descriptive study with cross-sectional method held in Department of Child Health Dr. Hasan Sadikin Hospital Bandung during July–October 2010, and statistical analysis using t–test Spearman rank correlation test. The result of the study showed that the right ventricle function examined by TAPSE method was different on preterm compared to term babies (p=0.006. No significant difference was found in the ejection fraction between preterm and term babies (p=0.22 and so did the shortening fraction (p=0.20. It was concluded that there is a difference in the right ventricle function by TAPSE method between preterm (lower and term babies.

  15. A Local Condensation Analysis Representing Two-phase Annular Flow in Condenser/radiator Capillary Tubes

    Karimi, Amir

    1991-01-01

    NASA's effort for the thermal environmental control of the Space Station Freedom is directed towards the design, analysis, and development of an Active Thermal Control System (ATCS). A two phase, flow through condenser/radiator concept was baselined, as a part of the ATCS, for the radiation of space station thermal load into space. The proposed condenser rejects heat through direct condensation of ATCS working fluid (ammonia) in the small diameter radiator tubes. Analysis of the condensation process and design of condenser tubes are based on the available two phase flow models for the prediction of flow regimes, heat transfer, and pressure drops. The prediction formulas use the existing empirical relationships of friction factor at gas-liquid interface. An attempt is made to study the stability of interfacial waves in two phase annular flow. The formulation is presented of a stability problem in cylindrical coordinates. The contribution of fluid viscosity, surface tension, and transverse radius of curvature to the interfacial surface is included. A solution is obtained for Kelvin-Helmholtz instability problem which can be used to determine the critical and most dangerous wavelengths for interfacial waves.

  16. Propagating nonpremixed edge-flames in a counterflow, annular slot burner under DC electric fields

    Tran, Vu Manh

    2016-09-11

    Characteristics of propagating nonpremixed edge-flames were investigated in a counterflow, annular slot burner. A high-voltage direct current (DC) was applied to the lower part of the burner and the upper part was grounded, creating electric field lines perpendicular to the direction of edge-flame propagation. Upon application of an electric field, an ionic wind is caused by the migration of positive and negative ions to lower and higher electrical potential sides of a flame, respectively. Under an applied DC, we found a significant decrease in edge-flame displacement speeds unlike several previous studies, which showed an increase in displacement speed. Within a moderate range of field intensity, we found effects on flame propagation speeds to be negligible after correcting the flame displacement speed with respect to the unburned flow velocity ahead of the flame edge. This indicates that the displacement speed of an edge-flame strongly depends on ionic wind and that an electric field has little or no impact on propagation speed. The ionic wind also influenced the location of the stoichiometric contour in front of the propagating edge in a given configuration such that a propagating edge was relocated to the higher potential side due to an imbalance between ionic winds originating from positive and negative ions. In addition, we observed a steadily wrinkled flame following transient propagation of the edge-flame, a topic for future research. © 2016 The Combustion Institute

  17. Simulations and measurements of adiabatic annular flows in triangular, tight lattice nuclear fuel bundle model

    Saxena, Abhishek, E-mail: asaxena@lke.mavt.ethz.ch [ETH Zurich, Laboratory for Nuclear Energy Systems, Department of Mechanical and Process Engineering, Sonneggstrasse 3, 8092 Zürich (Switzerland); Zboray, Robert [Laboratory for Thermal-hydraulics, Nuclear Energy and Safety Department, Paul Scherrer Institute, 5232 Villigen PSI (Switzerland); Prasser, Horst-Michael [ETH Zurich, Laboratory for Nuclear Energy Systems, Department of Mechanical and Process Engineering, Sonneggstrasse 3, 8092 Zürich (Switzerland); Laboratory for Thermal-hydraulics, Nuclear Energy and Safety Department, Paul Scherrer Institute, 5232 Villigen PSI (Switzerland)

    2016-04-01

    High conversion light water reactors (HCLWR) having triangular, tight-lattice fuels bundles could enable improved fuel utilization compared to present day LWRs. However, the efficient cooling of a tight lattice bundle has to be still proven. Major concern is the avoidance of high-quality boiling crisis (film dry-out) by the use of efficient functional spacers. For this reason, we have carried out experiments on adiabatic, air-water annular two-phase flows in a tight-lattice, triangular fuel bundle model using generic spacers. A high-spatial-resolution, non-intrusive measurement technology, cold neutron tomography, has been utilized to resolve the distribution of the liquid film thickness on the virtual fuel pin surfaces. Unsteady CFD simulations have also been performed to replicate and compare with the experiments using the commercial code STAR-CCM+. Large eddies have been resolved on the grid level to capture the dominant unsteady flow features expected to drive the liquid film thickness distribution downstream of a spacer while the subgrid scales have been modeled using the Wall Adapting Local Eddy (WALE) subgrid model. A Volume of Fluid (VOF) method, which directly tracks the interface and does away with closure relationship models for interfacial exchange terms, has also been employed. The present paper shows first comparison of the measurement with the simulation results.

  18. Investigation of the Left Ventricular Flow Dynamics in the Presence of Severe Mitral Annular Calcification

    El-Sayegh, Batoul; Kadem, Lyes; di Labbio, Giuseppe; Pressman, Gregg S.; Obasare, Edinrin

    2016-11-01

    Valvular calcification is frequent with aging and diverse diseases. Mitral annular calcification (MAC) is a degenerative process where the fibrous annulus of the mitral valve degrades. MAC can be found in approximately 40% of people aged over 65. It is associated with increased occurrence of cardiovascular diseases including stroke. This experimental work is aimed to investigate the effects of MAC on the left ventricle (LV) hemodynamics and to develop new clinical parameters. Two patient-specific 3D-printed mitral valves with moderate and severe MACs were placed in a left heart simulator. The velocity fields in the LV were acquired using time-resolved particle image velocimetry (TR-PIV) and compared to normal LV flow. The velocity fields were used to evaluate the temporal evolution of the vorticity fields and viscous energy loss in the LV. The presence of MAC disturbed the flow in the LV leading to markedly increased viscous energy losses. As the severity of MAC increased, the velocity of the inflow jet also increased causing significant perturbations to the normally-occurring vortex in the LV.

  19. Variability of the Coupling Between Surface Air Temperature and Northern Annular Mode at Various Levels

    TAN Benkui; SUO Lingling; HUANG Jiayou

    2008-01-01

    This article focuses on the variability of the coupling between surface air temperature(SAT)and northern annular mode(NAM)at various levels.To measure the coupling intensity between the SAT and the NAM anomaly fields.the coupling index has been defined as the leading principal component of the partial least squares regression model of the SAT and NAM anomalies.Both a composite analysis and the coupling index have been used to reveal level-by-level and month-to-month variability of the coupling between the upper anomalous NAM and the SAT in the Northern Hemisphere.The major results are as follows:the January SAT anomaly is more strongly coupled with the January NAM anomaly at the middle-upper tropospheric levels than that at the other levels,while the same is true for the February SAT anomaly with the January NAM anomaly at the lower stratospheric levels.The January NAM anomaly at the middleupper tropospheric levels is most strongly coupled with the January SAT anomaly,and the coupling intensity is successively reduced month by month and becomes trivial after April.The January NAM anomaly at the lower stratospheric levels is more strongly coupled with January,Febrnary and March SAT anomalies,but the coupling becomes trivial after April.

  20. A subset of annular lipids is linked to the flippase activity of an ABC transporter.

    Bechara, Chérine; Nöll, Anne; Morgner, Nina; Degiacomi, Matteo T; Tampé, Robert; Robinson, Carol V

    2015-03-01

    Lipids are critical components of membranes that could affect the properties of membrane proteins, yet the precise compositions of lipids surrounding membrane-embedded protein complexes is often difficult to discern. Here we report that, for the heterodimeric ABC transporter TmrAB, the extent of delipidation can be controlled by timed exposure to detergent. We subsequently characterize the cohort of endogenous lipids that are extracted in contact with the membrane protein complex, and show that with prolonged delipidation the number of neutral lipids is reduced in favour of their negatively charged counterparts. We show that lipid A is retained by the transporter and that the extent of its binding decreases during the catalytic cycle, implying that lipid A release is linked to adenosine tri-phosphate hydrolysis. Together, these results enable us to propose that a subset of annular lipids is invariant in composition, with negatively charged lipids binding tightly to TmrAB, and imply a role for this exporter in glycolipid translocation.

  1. Quantifying paleo-reconstruction skill of the Southern Annular Mode in a model framework

    Huiskamp, Willem; McGregor, Shayne; Batehup, Ryan

    2016-04-01

    The Southern Annular Mode (SAM) is the leading mode of atmospheric variability in the Southern Hemisphere. It impacts rainfall and surface air temperature throughout the hemisphere and is also responsible for a significant proportion of the variability in air-sea carbon exchange. The recent positive trend in the SAM over the last ~40 years has been linked to potential changes in ocean heat and carbon uptake, which could have a significant impact on the rate of anthropogenic warming. To investigate whether trends like this have occurred in the past, and how they may affect regional climate and atmospheric CO2, paleo-reconstructions of the SAM have been created spanning roughly the last millennium. Using the GFDL CM2.1 climate model, we attempt to assess the expected skill of these reconstructions using a pseudo-proxy approach and the popular weighted Composite Plus Scaling reconstruction method. This study covers non-stationary proxy-SAM relationships, the effects of calibration period length on reconstruction skill, the number of sites included in a reconstruction and the problem of relying too heavily on a single continent when sourcing proxies. We find that maximising the calibration window size, as well as sourcing proxies from a geographically diverse range of sites provides the most reliable reconstructions, accounting for up up to 58% of the model SAM variability (with realistic 31 year calibration window and 70 proxies).

  2. Heat transfer coefficient for flow boiling in an annular mini gap

    Hożejowska Sylwia

    2016-01-01

    Full Text Available The aim of this paper was to present the concept of mathematical models of heat transfer in flow boiling in an annular mini gap between the metal pipe with enhanced exterior surface and the external glass pipe. The one- and two-dimensional mathematical models were proposed to describe stationary heat transfer in the gap. A set of experimental data governed both the form of energy equations in cylindrical coordinates and the boundary conditions. The models were formulated to minimize the number of experimentally determined constants. Known temperature distributions in the enhanced surface and in the fluid helped to determine, from the Robin condition, the local heat transfer coefficients at the enhanced surface – fluid contact. The Trefftz method was used to find two-dimensional temperature distributions for the thermal conductive filler layer, enhanced surface and flowing fluid. The method of temperature calculation depended on whether the area of single-phase convection ended with boiling incipience in the gap or the two-phase flow region prevailed, with either fully developed bubbly flow or bubbly-slug flow. In the two–phase flow, the fluid temperature was calculated by Trefftz method. Trefftz functions for the Laplace equation and for the energy equation were used in the calculations.

  3. Formation of annular plasma downstream by magnetic aperture in the helicon experimental device

    Ghosh, Soumen; Yadav, S.; Barada, K. K.; Chattopadhyay, P. K.; Ghosh, J.; Pal, R.; Bora, D.

    2017-02-01

    In the Helicon eXperimental (HeX) device, the geometric aperture is fixed, but the position of the magnetic aperture can be varied. Working with Argon gas in the pressure range of 1 - 10 × 10 - 4 mbar, an annular plasma (density ˜ 10 16 m - 3 ) is formed downstream, always in front of the magnetic aperture. This occurs irrespective of the relative position of the geometric aperture or the presence of a radial electric field. This is in contrary to the earlier proposition made by others that a radial electric field is necessary to produce a hollow plasma profile. Instead, the ionization of neutrals in the radially outer region by the tail electrons, rotating fast due to gradient-B drift in the azimuthal direction, seems to account for the observed off-axis density peaking in the present experiment. This also explains the variation of the plasma annulus diameter seen here by changing the input radio frequency power ( 100 - 800 W ) .

  4. Heat transfer coefficient for flow boiling in an annular mini gap

    Hożejowska, Sylwia; Musiał, Tomasz; Piasecka, Magdalena

    2016-03-01

    The aim of this paper was to present the concept of mathematical models of heat transfer in flow boiling in an annular mini gap between the metal pipe with enhanced exterior surface and the external glass pipe. The one- and two-dimensional mathematical models were proposed to describe stationary heat transfer in the gap. A set of experimental data governed both the form of energy equations in cylindrical coordinates and the boundary conditions. The models were formulated to minimize the number of experimentally determined constants. Known temperature distributions in the enhanced surface and in the fluid helped to determine, from the Robin condition, the local heat transfer coefficients at the enhanced surface - fluid contact. The Trefftz method was used to find two-dimensional temperature distributions for the thermal conductive filler layer, enhanced surface and flowing fluid. The method of temperature calculation depended on whether the area of single-phase convection ended with boiling incipience in the gap or the two-phase flow region prevailed, with either fully developed bubbly flow or bubbly-slug flow. In the two-phase flow, the fluid temperature was calculated by Trefftz method. Trefftz functions for the Laplace equation and for the energy equation were used in the calculations.

  5. UNSTEADY HEAT TRANSFER IN AN ANNULAR PIPE. PART II: SWIRLING LAMINAR FLOW

    Kelvin Ho Choon Seng

    2012-02-01

    Full Text Available The   heat  transfer   problem  in   magnetocaloric regenerators  during  magnetization  has  been  described  and investigated for convective heat transfer by means of axial flow in part I of this series.   This work will focus on enhancing the unsteady heat  transfer using swirling laminar flow generated using axial vanes.   The governing parameters for this  studyare,  the  D*  ratio  (Inner  diameter/Outer  diameter  and  the swirl number, S.   The study is conducted  using  dimensional analysis and commercial CFD codes provided by ANSYS CFX. The  hydrodynamics and the  heat transfer of the  model are compared with data from similar cases found in literature and is found to be in the vicinity of good agreement.Keywords-  Annular ducts; unsteady heat transfer;  magnetic refrigeration/cooling;   swirling   laminar    flow;    dimensional analysis.

  6. Impact of wall shear stress on initial bacterial adhesion in rotating annular reactor.

    Saur, Thibaut; Morin, Emilie; Habouzit, Frédéric; Bernet, Nicolas; Escudié, Renaud

    2017-01-01

    The objective of this study was to investigate the bacterial adhesion under different wall shear stresses in turbulent flow and using a diverse bacterial consortium. A better understanding of the mechanisms governing microbial adhesion can be useful in diverse domains such as industrial processes, medical fields or environmental biotechnologies. The impact of wall shear stress-four values ranging from 0.09 to 7.3 Pa on polypropylene (PP) and polyvinyl chloride (PVC)-was carried out in rotating annular reactors to evaluate the adhesion in terms of morphological and microbiological structures. A diverse inoculum consisting of activated sludge was used. Epifluorescence microscopy was used to quantitatively and qualitatively characterize the adhesion. Attached bacterial communities were assessed by molecular fingerprinting profiles (CE-SSCP). It has been demonstrated that wall shear stress had a strong impact on both quantitative and qualitative aspects of the bacterial adhesion. ANOVA tests also demonstrated the significant impact of wall shear stress on all three tested morphological parameters (surface coverage, number of objects and size of objects) (p-values < 2.10-16). High wall shear stresses increased the quantity of attached bacteria but also altered their spatial distribution on the substratum surface. As the shear increased, aggregates or clusters appeared and their size grew when increasing the shears. Concerning the microbiological composition, the adhered bacterial communities changed gradually with the applied shear.

  7. Electrical Capacitance Probe Characterization in Vertical Annular Two-Phase Flow

    Grazia Monni

    2013-01-01

    Full Text Available The paper presents the experimental analysis and the characterization of an electrical capacitance probe (ECP that has been developed at the SIET Italian Company, for the measurement of two-phase flow parameters during the experimental simulation of nuclear accidents, as LOCA. The ECP is used to investigate a vertical air/water flow, characterized by void fraction higher than 95%, with mass flow rates ranging from 0.094 to 0.15 kg/s for air and from 0.002 to 0.021 kg/s for water, corresponding to an annular flow pattern. From the ECP signals, the electrode shape functions (i.e., the signals as a function of electrode distances in single- and two-phase flows are obtained. The dependence of the signal on the void fraction is derived and the liquid film thickness and the phase’s velocity are evaluated by means of rather simple models. The experimental analysis allows one to characterize the ECP, showing the advantages and the drawbacks of this technique for the two-phase flow characterization at high void fraction.

  8. Wall pressure measurements of flooding in vertical countercurrent annular air–water flow

    Choutapalli, I., Vierow, K.

    2010-01-01

    An experimental study of flooding in countercurrent air-water annular flow in a large diameter vertical tube using wall pressure measurements is described in this paper. Axial pressure profiles along the length of the test section were measured up to and after flooding using fast response pressure transducers for three representative liquid flow rates representing a wide range of liquid Reynolds numbers (ReL = 4Γ/μ; Γ is the liquid mass flow rate per unit perimeter; μ is the dynamic viscosity) from 3341 to 19,048. The results show that flooding in large diameter tubes cannot be initiated near the air outlet and is only initiated near the air inlet. Fourier analysis of the wall pressure measurements shows that up to the point of flooding, there is no dominant wave frequency but rather a band of frequencies encompassing both the low frequency and the broad band that are responsible for flooding. The data indicates that flooding in large diameter vertical tubes may be caused by the constructive superposition of a plurality of waves rather than the action of a single large-amplitude wave.

  9. Annularly grooved membrane combined with rood beam piezoresistive pressure sensor for low pressure applications.

    Li, Chuang; Cordovilla, Francisco; Ocaña, José L

    2017-03-01

    A novel structural piezoresistive pressure sensor with annularly grooved membrane combined with rood beam has been proposed for low pressure measurements based on silicon substrate. In this study, a design method, including the model design, dimensions optimization, and performance prediction of the novel structure sensor, is presented. The finite element method has been used to analyze the stress distribution of sensitive elements and the deflection of membrane. On the basis of simulation results, the relationships between structural dimension variables and mechanical performance are deduced, which make the fabrication processes more efficient. According to statistics theory, the coefficient of determination R(2) and residual sum of squares are introduced to indicate whether the fitting equations and curves match well with the simulation results. After that, a series of the optimal membrane dimensions are determined. Compared with other structural sensors, the optimized sensor achieves the best overall properties as it mitigates the contradiction between sensitivity and linearity. The reasons why the proposed sensor can maximize sensitivity and minimize nonlinearity are also discussed. By localizing more strain energy in the high concentrated stress profile and creating partially stiffened membrane, the proposed sensor has achieved a high sensitivity of 34.5 (mV/V)/psi and a low nonlinearity of 0.25% FSS. Thus, the proposed structure sensor will be a proper choice for low pressure applications less than 1 psi.

  10. Influences of physical properties of two-phase mixture on void fraction in an annular vessel

    LI Xiao-Ming; BI Qin-Cheng; FENG Quan-Ke; CHEN Ting-Kuan; DU She-Jiao

    2004-01-01

    To keep the void fraction of two-phase hydrogen in the moderator cell of the cold neutron source (CNS)of China Advanced Research Reactor (CARR) to a specified range, an annular vessel with the same size as the actual moderator cell was used as test section. Deionized water and alcohol, sucrose, and sodium chloride solutions with different concentrations were used as working fluid to find out influences of physical properties, such as density, viscosity and surface tension, of the two-phase mixture on void fraction. The tests proved that the ratio of surface tension to density of liquid phase has great influence on void fraction: the larger the ratio, the smaller the void fraction.Since the ratio of surface tension to density of Freon 113 is lower than that of liquid hydrogen, Freon 113 can be used as a working fluid to study the void fraction in the two-phase hydrogen thermosiphon loop in the CNS of CARR and the results will be conservative.

  11. Variance reduction techniques for 14 MeV neutron streaming problem in rectangular annular bent duct

    Ueki, Kotaro [Ship Research Inst., Mitaka, Tokyo (Japan)

    1998-03-01

    Monte Carlo method is the powerful technique for solving wide range of radiation transport problems. Its features are that it can solve the Boltzmann`s transport equation almost without approximation, and that the complexity of the systems to be treated rarely becomes a problem. However, the Monte Carlo calculation is always accompanied by statistical errors called variance. In shielding calculation, standard deviation or fractional standard deviation (FSD) is used frequently. The expression of the FSD is shown. Radiation shielding problems are roughly divided into transmission through deep layer and streaming problem. In the streaming problem, the large difference in the weight depending on the history of particles makes the FSD of Monte Carlo calculation worse. The streaming experiment in the 14 MeV neutron rectangular annular bent duct, which is the typical streaming bench mark experiment carried out of the OKTAVIAN of Osaka University, was analyzed by MCNP 4B, and the reduction of variance or FSD was attempted. The experimental system is shown. The analysis model by MCNP 4B, the input data and the results of analysis are reported, and the comparison with the experimental results was examined. (K.I.)

  12. Mono/dual-polarization refractive-index biosensors with enhanced sensitivity based on annular photonic crystals

    Jiang, Liyong; Zhang, We; Li, Xiangyin

    2014-01-01

    To promote the development of two-dimensional (2D) photonic crystals (PCs) based refractive-index (RI) biosensors, there is an urgent requirement of an effective approach to improve the RI sensitivity of 2D PCs (usually less than 500 nm/RIU). In this work, the photonic band gap (PBG) feature and the corresponding RI sensitivity of the air-ring type 2D annular PCs (APCs) have been studied in detail. Such type of 2D PCs can easily and apparently improve the RI sensitivity in comparison with conventional air-hole type 2D PCs that have been widely studied in previous works. This is because the APCs can naturally exhibit suppressed up edge of PBG that can strongly affect the final RI sensitivity. In general, an enhanced sensing performance of as high as up to 2-3 times RI sensitivity can be obtained from pure 2D APCs. Such high RI sensitivity is also available in three typical waveguides developed from pure 2D APCs. Furthermore, a new conception of dual-polarization RI biosensors has been proposed by defining the ...

  13. In-Plane free Vibration Analysis of an Annular Disk with Point Elastic Support

    S. Bashmal

    2011-01-01

    Full Text Available In-plane free vibrations of an elastic and isotropic annular disk with elastic constraints at the inner and outer boundaries, which are applied either along the entire periphery of the disk or at a point are investigated. The boundary characteristic orthogonal polynomials are employed in the Rayleigh-Ritz method to obtain the frequency parameters and the associated mode shapes. Boundary characteristic orthogonal polynomials are generated for the free boundary conditions of the disk while artificial springs are used to account for different boundary conditions. The frequency parameters for different boundary conditions of the outer edge are evaluated and compared with those available in the published studies and computed from a finite element model. The computed mode shapes are presented for a disk clamped at the inner edge and point supported at the outer edge to illustrate the free in-plane vibration behavior of the disk. Results show that addition of point clamped support causes some of the higher modes to split into two different frequencies with different mode shapes.

  14. Modelling of the measured longitudinal piezoelectric coefficient of single ceramic fibres with annular electrodes

    Pientschke, Christoph; Steinhausen, Ralf; Kern, Sabine; Beige, Horst

    2011-05-01

    A method for the measurement of the longitudinal piezoelectric coefficient d33 of single ceramic fibres with diameters 100-500 µm was recently developed. The voltage was applied using annular electrodes and the resulting displacement was measured by a capacitive method. In this paper, a number of calculations regarding the field distribution and the resulting piezoelectric displacement are presented for a typical lead zirconate titanate (PZT) ceramic. Provided that the fibres are ideally poled in the longitudinal direction, they can be modelled using the finite element method taking into account linear constitutive equations. The deviation of the measured and the actual d33 was modelled for a broad range of heights and diameters of the fibres and different electrode dimensions. The electric field distribution was analysed for typical examples and the influence of the mechanical stress on the measured d33 was studied. For sufficiently long and thin fibres the field distribution of the electric field is quite uniform and the d33 can be measured with high accuracy. Moreover, it was shown that for such fibres the measured piezoelectric coefficient d33 is determined by no other material parameter of the ceramics. The found trends of preferable geometries for the measurement can apparently be transferred to other piezoceramics.

  15. Lock-and-key dimerization in dense Brownian systems of hard annular sector particles

    Hodson, Wade D.; Mason, Thomas G.

    2016-08-01

    We develop a translational-rotational cage model that describes the behavior of dense two-dimensional (2D) Brownian systems of hard annular sector particles (ASPs), resembling C shapes. At high particle densities, pairs of ASPs can form mutually interdigitating lock-and-key dimers. This cage model considers either one or two mobile central ASPs which can translate and rotate within a static cage of surrounding ASPs that mimics the system's average local structure and density. By comparing with recent measurements made on dispersions of microscale lithographic ASPs [P. Y. Wang and T. G. Mason, J. Am. Chem. Soc. 137, 15308 (2015), 10.1021/jacs.5b10549], we show that mobile two-particle predictions of the probability of dimerization Pdimer, equilibrium constant K , and 2D osmotic pressure Π2 D as a function of the particle area fraction ϕA correspond closely to these experiments. By contrast, predictions based on only a single mobile particle do not agree well with either the two-particle predictions or the experimental data. Thus, we show that collective entropy can play an essential role in the behavior of dense Brownian systems composed of nontrivial hard shapes, such as ASPs.

  16. Lock-and-key dimerization in dense Brownian systems of hard annular sector particles.

    Hodson, Wade D; Mason, Thomas G

    2016-08-01

    We develop a translational-rotational cage model that describes the behavior of dense two-dimensional (2D) Brownian systems of hard annular sector particles (ASPs), resembling C shapes. At high particle densities, pairs of ASPs can form mutually interdigitating lock-and-key dimers. This cage model considers either one or two mobile central ASPs which can translate and rotate within a static cage of surrounding ASPs that mimics the system's average local structure and density. By comparing with recent measurements made on dispersions of microscale lithographic ASPs [P. Y. Wang and T. G. Mason, J. Am. Chem. Soc. 137, 15308 (2015)JACSAT0002-786310.1021/jacs.5b10549], we show that mobile two-particle predictions of the probability of dimerization P_{dimer}, equilibrium constant K, and 2D osmotic pressure Π_{2D} as a function of the particle area fraction ϕ_{A} correspond closely to these experiments. By contrast, predictions based on only a single mobile particle do not agree well with either the two-particle predictions or the experimental data. Thus, we show that collective entropy can play an essential role in the behavior of dense Brownian systems composed of nontrivial hard shapes, such as ASPs.

  17. Wall Shear Stress, Wall Pressure and Near Wall Velocity Field Relationships in a Whirling Annular Seal

    Morrison, Gerald L.; Winslow, Robert B.; Thames, H. Davis, III

    1996-01-01

    The mean and phase averaged pressure and wall shear stress distributions were measured on the stator wall of a 50% eccentric annular seal which was whirling in a circular orbit at the same speed as the shaft rotation. The shear stresses were measured using flush mounted hot-film probes. Four different operating conditions were considered consisting of Reynolds numbers of 12,000 and 24,000 and Taylor numbers of 3,300 and 6,600. At each of the operating conditions the axial distribution (from Z/L = -0.2 to 1.2) of the mean pressure, shear stress magnitude, and shear stress direction on the stator wall were measured. Also measured were the phase averaged pressure and shear stress. These data were combined to calculate the force distributions along the seal length. Integration of the force distributions result in the net forces and moments generated by the pressure and shear stresses. The flow field inside the seal operating at a Reynolds number of 24,000 and a Taylor number of 6,600 has been measured using a 3-D laser Doppler anemometer system. Phase averaged wall pressure and wall shear stress are presented along with phase averaged mean velocity and turbulence kinetic energy distributions located 0.16c from the stator wall where c is the seal clearance. The relationships between the velocity, turbulence, wall pressure and wall shear stress are very complex and do not follow simple bulk flow predictions.

  18. Design of an Annular Linear Induction Pump for Nuclear Space Applications

    Carloa O. Maidana; James E. Werner; Daniel M. Wachs

    2011-02-01

    Abstract. The United States Department of Energy's (DOE) Office of Nuclear Energy, Science, and Technology is supporting the National Aeronautics and Space Administration (NASA) in evaluating space mission power, propulsion systems and technologies to support the implementation of the Vision for Space Exploration (VSE). NASA will need increased power for propulsion and for surface power applications to support both robotic and human space exploration missions. As part of the Fission Surface Power Technology Project for the development of nuclear reactor technologies for multi-mission spacecrafts, an Annular Linear Induction Pump, a type of Electromagnetic Pump for liquid metals, able to operate in space has to be designed. Results of such design work are described as well as the fundamental ideas behind the development of an optimized design methodology. This project, which is a collaboration between Idaho National Laboratory (INL), Pacific Northwest National Laboratory (PNNL) and Marshall Space Flight Center (MSFC), involves the use of theoretical, computational and experimental tools for multi-physics analysis as well as advanced engineering design methods and techniques.

  19. Effect of gas diffusion layer and membrane properties in an annular proton exchange membrane fuel cell

    Khazaee, I.; Ghazikhani, M.; Esfahani, M. Nasr

    2012-01-01

    A complete three-dimensional and single phase computational dynamics model for annular proton exchange membrane (PEM) fuel cell is used to investigate the effect of changing gas diffusion layer and membrane properties on the performances, current density and gas concentration. The proposed model is a full cell model, which includes all the parts of the PEM fuel cell, flow channels, gas diffusion electrodes, catalyst layers and the membrane. Coupled transport and electrochemical kinetics equations are solved in a single domain; therefore no interfacial boundary condition is required at the internal boundaries between cell components. This computational fluid dynamics code is used as the direct problem solver, which is used to simulate the two-dimensional mass, momentum and species transport phenomena as well as the electron- and proton-transfer process taking place in a PEMFC that cannot be investigated experimentally. The results show that by increasing the thickness and decreasing the porosity of GDL the performance of the cell enhances that it is different with planner PEM fuel cell. Also the results show that by decreasing the thickness of the membrane the performance of the cell increases.

  20. Simultaneous Oscillation of Annular Solid ^4He Samples at Two Mode Frequencies in Compound Torsion Pendulum

    Keiderling, Michael C.; Kojima, Harry

    2009-03-01

    We have extended our studies on the non-classical behavior of solid ^4He contained in compound torsional oscillator (TO) cell below 1 K. Our unique TO design allows observations on the identical sample at two distinct frequencies(f1=493 and f2=1165 Hz). The sample was grown by blocked capillary method in an annular cell(id = 8.0 mm, od = 10.0 mm, height = 9.0 mm). We focus here on experiments in which the two modes are excited simultaneously. While keeping the drive of f2 mode at a very low level, the drive of f1 mode was varied from high to low levels to produce substantial variations in the non-classical rotation inertia fraction (NCRIf). When the NCRIf seen by f1 mode is reduced by 89, 91 and 94 % at 9.7, 23.5 and 56.5 mK, respectively, the NCRIf seen by f2 mode (driven at low level) is reduced by 62, 68 and 80 %. The discrepancies and their temperature dependence in the observed reductions in NCRIf are not yet understood. Similar Measurements with the roles of the drive levels of the modes reversed as well as the changes in the dissipation of the torsional oscillator during the simultaneous drive will be reported.