Nayak, Ashok Ranjan; Karade, Sharanbasappa Shrimant; Srivastava, Vijay Kumar; Rana, Ajay Kumar; Gupta, C M; Sahasrabuddhe, Amogh A; Pratap, J Venkatesh
2016-07-01
Coiled coils are ubiquitous structural motifs that serve as a platform for protein-protein interactions and play a central role in myriad physiological processes. Though the formation of a coiled coil requires only the presence of suitably spaced hydrophobic residues, sequence specificities have also been associated with specific oligomeric states. RhXXhE is one such sequence motif, associated with parallel trimers, found in coronins and other proteins. Coronin, present in all eukaryotes, is an actin-associated protein involved in regulating actin turnover. Most eukaryotic coronins possess the RhXXhE trimerization motif. However, a unique feature of parasitic kinetoplastid coronin is that the positions of R and E are swapped within their coiled coil domain, but were still expected to form trimers. To understand the role of swapped motif in oligomeric specificity, we determined the X-ray crystal structure of Leishmania donovani coronin coiled coil domain (LdCoroCC) at 2.2Å, which surprisingly, reveals an anti-parallel tetramer assembly. Small angle X-ray scattering studies and chemical crosslinking confirm the tetramer in solution and is consistent with the oligomerization observed in the full length protein. Structural analyses reveal that LdCoroCC possesses an inherent asymmetry, in that one of the helices of the bundle is axially shifted with respect to the other three. The analysis also identifies steric reasons that cause this asymmetry. The bundle adapts an extended a-d-e core packing, the e residue being polar (with an exception) which results in a thermostable bundle with polar and apolar interfaces, unlike the existing a-d-e core antiparallel homotetramers with apolar core. Functional implications of the anti-parallel association in kinetoplastids are discussed. PMID:26940672
Gonella, Grazia; Dai, Hai-Lung; Fry, H Christopher; Therien, Michael J; Krishnan, Venkata; Tronin, Andrey; Blasie, J Kent
2010-07-21
The macroscopic nonlinear optical response of the "push-pull" chromophore RuPZn incorporated into a single monolayer of the amphiphilic 4-helix bundle peptide (AP0) covalently attached to a solid substrate at high in-plane density has been measured. The second-order susceptibility, chi(zzz), was found to be in the range of approximately 15 x 10(-9) esu, consistent with a coherent sum of the nonlinear contributions from the individual chromophores (beta) as previously measured in isotropic solution through hyper-Rayleigh scattering as well as estimated from theoretical calculations. The microscopic hyperpolarizability of the RuPZn chromophore is preserved upon incorporation into the peptide monolayer, suggesting that the chromophore-chromophore interactions in the densely packed ensemble do not substantially affect the first-order molecular hyperpolarizability. The polarization angle dependence of the second harmonic signal reveals that the chromophore is vectorially oriented in the two-dimensional ensemble. Analysis of the order parameter together with information obtained from grazing incidence X-ray diffraction help in determining the chromophore orientation within the AP0-RuPZn monolayer. Taking into account an average pitch angle of approximately 20 degrees characterizing the coiled-coil structure of the peptide bundle, the width of the bundle's tilt angle distribution should be sigma < or = 20 degrees, resulting in a mean value of the tilt angle 23 degrees < or = theta(0) < or = 37 degrees. PMID:20578696
Dynamics of flagellar bundling
Janssen, Pieter; Graham, Michael
2010-11-01
Flagella are long thin appendages of microscopic organisms used for propulsion in low-Reynolds environments. For E. coli the flagella are driven by a molecular motor, which rotates the flagella in a counter-clockwise motion (CCM). When in a forward swimming motion, all flagella bundle up. If a motor reverses rotation direction, the flagella unbundle and the cell makes a tumbling motion. When all motors turn in the same CC direction again, the flagella bundle up, and forward swimming continues. To investigate the bundling, we consider two flexible helices next to each other, as well as several flagella attached to a spherical body. Each helix is modeled as several prolate spheroids connected at the tips by springs. For hydrodynamic interactions, we consider the flagella to made up of point forces, while the finite size of the body is incorporated via Fax'en's laws. We show that synchronization occurs quickly relative to the bundling process. For flagella next to each other, the initial deflection is generated by rotlet interactions generated by the rotating helices. At longer times, simulations show the flagella only wrap once around each other, but only for flagella that are closer than about 4 helix radii. Finally, we show a run-and-tumble motion of the body with attached flagella.
Chen, Yongmin; Li, Jianpei
2015-01-01
When procuring multiple products from competing firms, a buyer may choose separate purchase, pure bundling, or mixed bundling. We show that pure bundling will generate higher buyer surplus than both separate purchase and mixed bundling, provided that trade for each good is likely to be efficient. Pure bundling is superior because it intensifies the competition between firms by reducing their cost asymmetry. Mixed bundling is inferior because it allows firms to coordinate to ...
Heal, Geoffrey
2002-01-01
Biodiversity provides essential services to human societies. Many of these services are provided as public goods, so that they will typically be underprovided both by market mechanisms (because of the impossibility of excluding non-payers from using the services) and by government-run systems (because of the free rider problem). I suggest here that in some cases the public goods provided by biodiversity conservation can be bundled with private goods and their value to consumers captured in th...
International Nuclear Information System (INIS)
This patent describes a method of forming a fuel bundle of a nuclear reactor. The method consists of positioning the fuel rods in the bottom plate, positioning the tie rod in the bottom plate with the key passed through the receptacle to the underside of the bottom plate and, after the tie rod is so positioned, turning the tie rod so that the key is in engagement with the underside of the bottom plate. Thereafter mounting the top plate is mounted in engagement with the fuel rods with the upper end of the tie rod extending through the opening in the top plate and extending above the top plate, and the tie rod is secured to the upper side of sid top plate thus simultaneously securing the key to the underside of the bottom plate
Hildebrand, Joanne M.; Tanzer, Maria C; Lucet, Isabelle S; Young, Samuel N.; Spall, Sukhdeep K; Sharma, Pooja; Pierotti, Catia; Garnier, Jean-Marc; Dobson, Renwick C. J.; Andrew I Webb; Tripaydonis, Anne; Babon, Jeffrey J.; Mulcair, Mark D.; Scanlon, Martin J.; Alexander, Warren S
2014-01-01
The four-helix bundle (4HB) domain of Mixed Lineage Kinase Domain-Like (MLKL) bears two clusters of residues that are required for cell death by necroptosis. Mutations within a cluster centered on the α4 helix of the 4HB domain of MLKL prevented its membrane translocation, oligomerization, and ability to induce necroptosis. This cluster is composed principally of acidic residues and therefore challenges the idea that the 4HB domain engages negatively charged phospholipid membranes via a conve...
International Nuclear Information System (INIS)
The increase of bundle supply has become widespread in several sectors (for instance in telecommunications and energy fields). This paper review relates strategic aspects of bundling. The main purpose of this paper is to analyze profitability of bundling strategies according to the degree of competition and the characteristics of goods. Moreover, bundling can be used as price discrimination tool, screening device or entry barriers. In monopoly case bundling strategy is efficient to sort consumers in different categories in order to capture a maximum of surplus. However, when competition increases, the profitability on bundling strategies depends on correlation of consumers' reservations values. (author)
Murray, Michael K; Stevenson, Danny; Vozzo, Raymond F
2015-01-01
We develop the theory of simplicial extensions for bundle gerbes and their characteristic classes. This formalism is used to study descent problems and equivariance for bundle gerbes. We consider in detail two examples: the basic bundle gerbe on a unitary group and a string structure for a principal bundle. We show that the basic bundle gerbe is equivariant for the conjugation action and calculate its characteristic class and that a string structure gives rise to a bundle gerbe which is equivariant for a natural action of the String 2-group.
Bundling in Telecommunications
Begoña García-Mariñoso; Xavier Martinez-Giralt; Pau Olivella
2008-01-01
The paper offers an overview of the literature on bundling in the telecommunications sector and its application in the Spanish market. We argue that the use of bundling in the provision of services is associated to technological reasons. Therefore, there appears no need to regulate bundling activities. However, this is not to say that other related telecom markets should not be scrutinized and regulated, or that the regulator should not pay attention to other bundling-related anticompetitive ...
Nicholas Economides
2014-01-01
We discuss strategic ways that sellers can use tying and bundling with requirement conditions to extract consumer surplus. We analyze different types of tying and bundling creating (i) intra-product price discrimination; (ii) intra-consumer price discrimination; and (iii) inter-product price discrimination, and assess the antitrust liability that these practices may entail. We also discuss the impact on consumers and competition, as well as potential antitrust liability of bundling “incontest...
Lerman, Eugene
2003-01-01
We define contact fiber bundles and investigate conditions for the existence of contact structures on the total space of such a bundle. The results are analogous to minimal coupling in symplectic geometry. The two applications are construction of K-contact manifolds generalizing Yamazaki's fiber join construction and a cross-section theorem for contact moment maps
Principal noncommutative torus bundles
DEFF Research Database (Denmark)
Echterhoff, Siegfried; Nest, Ryszard; Oyono-Oyono, Herve
2008-01-01
of bivariant K-theory (denoted RKK-theory) due to Kasparov. Using earlier results of Echterhoff and Williams, we shall give a complete classification of principal non-commutative torus bundles up to equivariant Morita equivalence. We then study these bundles as topological fibrations (forgetting the...
Restrictions of stable bundles
Balaji, V
2011-01-01
The Mehta-Ramanathan theorem ensures that the restriction of a stable vector bundle to a sufficiently high degree complete intersection curve is again stable. We improve the bounds for the "sufficiently high degree" and propose a possibly optimal conjecture.
International Nuclear Information System (INIS)
This paper describes works on CANDU fuel bundle fabrication in the Fuel Fabrication Development and Testing Section (FFDT) of AECL's Chalk River Laboratories. This work does not cover fuel design, pellet manufacturing, Zircaloy material manufacturing, but cover the joining of appendages to sheath tube, endcap preparation and welding, UO2 loading, end plate preparation and welding, and all inspections required in these steps. Materials used in the fabrication of CANDU fuel bundle are: 1)Ceramic UO2 Pellet 2)Zircaloy -4. Fuel Bundle Structural Material 3) Others (Zinc stearate, Colloidal graphite, Beryllium and Heium). Th fabrication of fuel element consist of three process: 1)pellet loading into the sheats, 2) endcap welding, and 3) the element profiling. Endcap welds is tested by metallography and He leak test. The endcaps of the elements are welded to the end plates to form the 37- element bundle assembly
Subtleties Concerning Conformal Tractor Bundles
Graham, C Robin
2012-01-01
The realization of tractor bundles as associated bundles in conformal geometry is studied. It is shown that different natural choices of principal bundle with normal Cartan connection corresponding to a given conformal manifold can give rise to topologically distinct associated tractor bundles for the same inducing representation. Consequences for homogeneous models and conformal holonomy are described. A careful presentation is made of background material concerning standard tractor bundles and equivalence between parabolic geometries and underlying structures.
DEFF Research Database (Denmark)
Bussink, Barbara E; Holst, Anders Gaarsdal; Jespersen, Lasse;
2013-01-01
AimsTo determine the prevalence, predictors of newly acquired, and the prognostic value of right bundle branch block (RBBB) and incomplete RBBB (IRBBB) on a resting 12-lead electrocardiogram in men and women from the general population.Methods and resultsWe followed 18 441 participants included in...... men vs. 0.5%/2.3% in women, P <0.001). Significant predictors of newly acquired RBBB were male gender, increasing age, high systolic blood pressure, and presence of IRBBB, whereas predictors of newly acquired IRBBB were male gender, increasing age, and low BMI. Right bundle branch block was associated...... with significantly increased all-cause and cardiovascular mortality in both genders with age-adjusted hazard ratios (HR) of 1.31 [95% confidence interval (CI), 1.11-1.54] and 1.87 (95% CI, 1.48-2.36) in the gender pooled analysis with little attenuation after multiple adjustment. Right bundle branch...
Principal -bundles on Nodal Curves
Indian Academy of Sciences (India)
Usha N Bhosle
2001-08-01
Let be a connected semisimple affine algebraic group defined over . We study the relation between stable, semistable -bundles on a nodal curve and representations of the fundamental group of . This study is done by extending the notion of (generalized) parabolic vector bundles to principal -bundles on the desingularization of and using the correspondence between them and principal -bundles on . We give an isomorphism of the stack of generalized parabolic bundles on with a quotient stack associated to loop groups. We show that if is simple and simply connected then the Picard group of the stack of principal -bundles on is isomorphic to ⊕ , being the number of components of .
International Nuclear Information System (INIS)
A hybrid bundle divertor design is presented that produces <0.3% magnetic ripple at the center of the plasma while providing adequate space for the coil shielding and structure for a tokamak fusion test reactor similar to the International Tokamak Reactor and the Engineering Test Facility (with R = 5 m, B = 5 T, and a /SUB wall/ = 1.5 m, in particular). This hybrid divertor consists of a set of quadrupole ''wing'' coils running tangent to the tokamak plasma on either side of a bundle divertor. The wing coils by themselves pull the edge of the plasma out 1.5 m and spread the thickness of the scrape-off layer from 0.1 to 0.7 m at the midplane. The clear aperture of the bundle divertor throat is 1.0 m high and 1.8 m wide. For maintenance or replacement, the hybrid divertor can be disassembled into three parts, with the bundle divertor part pulling straight out between toroidal field coils and the wing coils then sliding out through the same opening
On framed quantum principal bundles
Durdevic, M
1995-01-01
A noncommutative-geometric formalism of framed principal bundles is sketched, in a special case of quantum bundles (over quantum spaces) possessing classical structure groups. Quantum counterparts of torsion operators and Levi-Civita type connections are analyzed. A construction of a natural differential calculus on framed bundles is described. Illustrative examples are presented.
Directory of Open Access Journals (Sweden)
D. A. Robbins
1994-12-01
Full Text Available We study bundles of Banach algebras ÃÂ€:AÃ¢Â†Â’X, where each fiber Ax=ÃÂ€Ã¢ÂˆÂ’1({x} is a Banach algebra and X is a compact Hausdorff space. In the case where all fibers are commutative, we investigate how the Gelfand representation of the section space algebra ÃŽÂ“(ÃÂ€ relates to the Gelfand representation of the fibers. In the general case, we investigate how adjoining an identity to the bundle ÃÂ€:AÃ¢Â†Â’X relates to the standard adjunction of identities to the fibers.
Rudakov, A N
1990-01-01
This volume is devoted to the use of helices as a method for studying exceptional vector bundles, an important and natural concept in algebraic geometry. The work arises out of a series of seminars organised in Moscow by A. N. Rudakov. The first article sets up the general machinery, and later ones explore its use in various contexts. As to be expected, the approach is concrete; the theory is considered for quadrics, ruled surfaces, K3 surfaces and P3(C).
Hirsch, Gregory
2002-01-01
A plurality of glass or metal wires are precisely etched to form the desired shape of the individual channels of the final polycapillary optic. This shape is created by carefully controlling the withdrawal speed of a group of wires from an etchant bath. The etched wires undergo a subsequent operation to create an extremely smooth surface. This surface is coated with a layer of material which is selected to maximize the reflectivity of the radiation being used. This reflective surface may be a single layer of material, or a multilayer coating for optimizing the reflectivity in a narrower wavelength interval. The collection of individual wires is assembled into a close-packed multi-wire bundle, and the wires are bonded together in a manner which preserves the close-pack configuration, irrespective of the local wire diameter. The initial wires are then removed by either a chemical etching procedure or mechanical force. In the case of chemical etching, the bundle is generally segmented by cutting a series of etching slots. Prior to removing the wire, the capillary array is typically bonded to a support substrate. The result of the process is a bundle of precisely oriented radiation-reflecting hollow channels. The capillary optic is used for efficiently collecting and redirecting the radiation from a source of radiation which could be the anode of an x-ray tube, a plasma source, the fluorescent radiation from an electron microprobe, a synchrotron radiation source, a reactor or spallation source of neutrons, or some other source.
Bundling harvester; Nippukorjausharvesteri
Energy Technology Data Exchange (ETDEWEB)
Koponen, K. [Eko-Log Oy, Kuopio (Finland)
1996-12-31
The staring point of the project was to design and construct, by taking the silvicultural point of view into account, a harvesting and processing system especially for energy-wood, containing manually driven bundling harvester, automatizing of the harvester, and automatized loading. The equipment forms an ideal method for entrepreneur`s-line harvesting. The target is to apply the system also for owner`s-line harvesting. The profitability of the system promotes the utilization of the system in both cases. The objectives of the project were: to construct a test equipment and prototypes for all the project stages, to carry out terrain and strain tests in order to examine the usability and durability, as well as the capacity of the machine, to test the applicability of the Eko-Log system in simultaneous harvesting of energy and pulp woods, and to start the marketing and manufacturing of the products. The basic problems of the construction of the bundling harvester have been solved using terrain-tests. The prototype machine has been shown to be operable. Loading of the bundles to form sufficiently economically transportable loads has been studied, and simultaneously, the branch-biomass has been tried to be utilized without loosing the profitability of transportation. The results have been promising, and will promote the profitable utilization of wood-energy
DEFF Research Database (Denmark)
Sommer, Stefan Horst; Lauze, Francois Bernard; Nielsen, Mads; Pennec, Xavier
information to be automatically incorporated in registrations and promises to improve the standard framework in several aspects. We present the mathematical foundations of LDDKBM and derive the KB-EPDiff evolution equations, which provide optimal warps in this new framework. To illustrate the resulting......In the LDDMM framework, optimal warps for image registration are found as end-points of critical paths for an energy functional, and the EPDiff equations describe the evolution along such paths. The Large Deformation Diffeomorphic Kernel Bundle Mapping (LDDKBM) extension of LDDMM allows scale space...... diffeomorphism paths, we give examples showing the decoupled evolution across scales and how the method automatically incorporates deforma- tion at appropriate scales....
Cassou-Nogues, Ph.; Erez, B.; Taylor, M. J.
2004-01-01
We establish comparison results between the Hasse-Witt invariants w_t(E) of a symmetric bundle E over a scheme and the invariants of one of its twists E_{\\alpha}. For general twists we describe the difference between w_t(E) and w_t(E_{\\alpha}) up to terms of degree 3. Next we consider a special kind of twist, which has been studied by A. Fr\\"ohlich. This arises from twisting by a cocycle obtained from an orthogonal representation. We show how to explicitly describe the twist for representatio...
International Nuclear Information System (INIS)
This report is a summary of experimental investigations describing the fuel rod behavior in the refilling and reflooding phase of a loss-of-coolant accident of a PWR. The experiments were performed with 5x5 and 7x7 rod bundles, using indirectly electrically heated fuel rod simulators of full length with original PWR-KWU-geometry, original grid spacers and Zircaloy-4-claddings (Type Biblis B). The fuel rod simulators showed a cosine shaped axial power profile in 7 steps and continuous, respectively. The results describe the influence of the different parameters such as bundle size on the maximum coolant channel blockage, that of the cooling on the size of the circumferential strain of the cladding (azimuthal temperature distribution) a cold control rod guide thimble and the flow direction (axial temperature distribution) on the resulting coolant channel blockage. The rewetting behavior of different fuel rod simulators including ballooned and burst Zircaloy claddings is discussed as well as the influence of thermocouples on the cladding temperature history and the rewetting behavior. All results prove the coolability of a PWR in the case of a LOCA. Therefore, it can be concluded that the ECC-criteria established by licensing authorities can be fulfilled. (orig./HP)
Bundle Security Protocol for ION
Burleigh, Scott C.; Birrane, Edward J.; Krupiarz, Christopher
2011-01-01
This software implements bundle authentication, conforming to the Delay-Tolerant Networking (DTN) Internet Draft on Bundle Security Protocol (BSP), for the Interplanetary Overlay Network (ION) implementation of DTN. This is the only implementation of BSP that is integrated with ION.
CANFLEX fuel bundle impact test
International Nuclear Information System (INIS)
This document outlines the test results for the impact test of the CANFLEX fuel bundle. Impact test is performed to determine and verify the amount of general bundle shape distortion and defect of the pressure tube that may occur during refuelling. The test specification requires that the fuel bundles and the pressure tube retain their integrities after the impact test under the conservative conditions (10 stationary bundles with 31kg/s flow rate) considering the pressure tube creep. The refuelling simulator operating with pneumatic force and simulated shield plug were fabricated and the velocity/displacement transducer and the high speed camera were also used in this test. The characteristics of the moving bundle (velocity, displacement, impacting force) were measured and analyzed with the impact sensor and the high speed camera system. The important test procedures and measurement results were discussed as follows. 1) Test bundle measurements and the pressure tube inspections 2) Simulated shield plug, outlet flange installation and bundle loading 3) refuelling simulator, inlet flange installation and sensors, high speed camera installation 4) Perform the impact test with operating the refuelling simulator and measure the dynamic characteristics 5) Inspections of the fuel bundles and the pressure tube. (author). 8 refs., 23 tabs., 13 figs
CANFLEX fuel bundle impact test
Energy Technology Data Exchange (ETDEWEB)
Chang, Seok Kyu; Chung, C. H.; Park, J. S.; Hong, S. D.; Kim, B. D.
1997-08-01
This document outlines the test results for the impact test of the CANFLEX fuel bundle. Impact test is performed to determine and verify the amount of general bundle shape distortion and defect of the pressure tube that may occur during refuelling. The test specification requires that the fuel bundles and the pressure tube retain their integrities after the impact test under the conservative conditions (10 stationary bundles with 31kg/s flow rate) considering the pressure tube creep. The refuelling simulator operating with pneumatic force and simulated shield plug were fabricated and the velocity/displacement transducer and the high speed camera were also used in this test. The characteristics of the moving bundle (velocity, displacement, impacting force) were measured and analyzed with the impact sensor and the high speed camera system. The important test procedures and measurement results were discussed as follows. 1) Test bundle measurements and the pressure tube inspections 2) Simulated shield plug, outlet flange installation and bundle loading 3) refuelling simulator, inlet flange installation and sensors, high speed camera installation 4) Perform the impact test with operating the refuelling simulator and measure the dynamic characteristics 5) Inspections of the fuel bundles and the pressure tube. (author). 8 refs., 23 tabs., 13 figs.
Fiber Bundles and Parseval Frames
Agrawal, Devanshu; Knisley, Jeff
2015-01-01
Continuous frames over a Hilbert space have a rich and sophisticated structure that can be represented in the form of a fiber bundle. The fiber bundle structure reveals the central importance of Parseval frames and the extent to which Parseval frames generalize the notion of an orthonormal basis.
Fiber bundle phase conjugate mirror
Ward, Benjamin G.
2012-05-01
An improved method and apparatus for passively conjugating the phases of a distorted wavefronts resulting from optical phase mismatch between elements of a fiber laser array are disclosed. A method for passively conjugating a distorted wavefront comprises the steps of: multiplexing a plurality of probe fibers and a bundle pump fiber in a fiber bundle array; passing the multiplexed output from the fiber bundle array through a collimating lens and into one portion of a non-linear medium; passing the output from a pump collection fiber through a focusing lens and into another portion of the non-linear medium so that the output from the pump collection fiber mixes with the multiplexed output from the fiber bundle; adjusting one or more degrees of freedom of one or more of the fiber bundle array, the collimating lens, the focusing lens, the non-linear medium, or the pump collection fiber to produce a standing wave in the non-linear medium.
Twisted Vector Bundles on Pointed Nodal Curves
Indian Academy of Sciences (India)
Ivan Kausz
2005-05-01
Motivated by the quest for a good compactification of the moduli space of -bundles on a nodal curve we establish a striking relationship between Abramovich’s and Vistoli’s twisted bundles and Gieseker vector bundles.
The Atiyah Bundle and Connections on a Principal Bundle
Indian Academy of Sciences (India)
Indranil Biswas
2010-06-01
Let be a ∞ manifold and a Lie a group. Let $E_G$ be a ∞ principal -bundle over . There is a fiber bundle $\\mathcal{C}(E_G)$ over whose smooth sections correspond to the connections on $E_G$. The pull back of $E_G$ to $\\mathcal{C}(E_G)$ has a tautological connection. We investigate the curvature of this tautological connection.
DEFF Research Database (Denmark)
Risum, Niels; Strauss, David; Sogaard, Peter;
2013-01-01
The relationship between myocardial electrical activation by electrocardiogram (ECG) and mechanical contraction by echocardiography in left bundle-branch block (LBBB) has never been clearly demonstrated. New strict criteria for LBBB based on a fundamental understanding of physiology have recently...
Bundling ecosystem services in Denmark
DEFF Research Database (Denmark)
Turner, Katrine Grace; Odgaard, Mette Vestergaard; Bøcher, Peder Klith; Dalgaard, Tommy; Svenning, J.-C.
2014-01-01
We made a spatial analysis of 11 ecosystem services at a 10 km × 10 km grid scale covering most of Denmark. Our objective was to describe their spatial distribution and interactions and also to analyze whether they formed specific bundle types on a regional scale in the Danish cultural landscape....... We found clustered distribution patterns of ecosystem services across the country. There was a significant tendency for trade-offs between on the one hand cultural and regulating services and on the other provisioning services, and we also found the potential of regulating and cultural services to...... form synergies. We identified six distinct ecosystem service bundle types, indicating multiple interactions at a landscape level. The bundle types showed specialized areas of agricultural production, high provision of cultural services at the coasts, multifunctional mixed-use bundle types around urban...
Structure of the acrosomal bundle.
Schmid, Michael F; Sherman, Michael B; Matsudaira, Paul; Chiu, Wah
2004-09-01
In the unactivated Limulus sperm, a 60- micro m-long bundle of actin filaments crosslinked by the protein scruin is bent and twisted into a coil around the base of the nucleus. At fertilization, the bundle uncoils and fully extends in five seconds to support a finger of membrane known as the acrosomal process. This biological spring is powered by stored elastic energy and does not require the action of motor proteins or actin polymerization. In a 9.5-A electron cryomicroscopic structure of the extended bundle, we show that twist, tilt and rotation of actin-scruin subunits deviate widely from a 'standard' F-actin filament. This variability in structural organization allows filaments to pack into a highly ordered and rigid bundle in the extended state and suggests a mechanism for storing and releasing energy between coiled and extended states without disassembly. PMID:15343340
Locking means for fuels bundles
International Nuclear Information System (INIS)
A nuclear power reactor fuel bundle is described which has a plurality of fuel rods disposed between two end plates positioned by tie rods extending therebetween. The assembled bundle is secured by one or more locking forks which pass through slots in the tie rod ends. Springs mounted on the fuel rods and tie rods are compressed by assembling the bundle and forcing one end plate against the locking fork to maintain the fuel rods and tie rods in position between the end plates. Downward pressure on the end plate permits removal of the locking fork so that the end plates may be removed, thus giving access to the fuel rods. This construction facilitates disassembly of an irradiated fuel bundle under water
Kun, Ferenc; Zapperi, Stefano; Herrmann, Hans J.
1999-01-01
We introduce a continuous damage fiber bundle model that gives rise to macroscopic plasticity and compare its behavior with that of dry fiber bundles. Several interesting constitutive behaviors are found in this model depending on the value of the damage parameter and on the form of the disorder distribution. In addition, we compare the behavior of global load transfer models with local load transfer models and study in detail the damage evolution before failure. We emphasize the analogies be...
Holomorphic bundles over elliptic manifolds
International Nuclear Information System (INIS)
In this lecture we shall examine holomorphic bundles over compact elliptically fibered manifolds. We shall examine constructions of such bundles as well as (duality) relations between such bundles and other geometric objects, namely K3-surfaces and del Pezzo surfaces. We shall be dealing throughout with holomorphic principal bundles with structure group GC where G is a compact, simple (usually simply connected) Lie group and GC is the associated complex simple algebraic group. Of course, in the special case G = SU(n) and hence GC = SLn(C), we are considering holomorphic vector bundles with trivial determinant. In the other cases of classical groups, G SO(n) or G = Sympl(2n) we are considering holomorphic vector bundles with trivial determinant equipped with a non-degenerate symmetric, or skew symmetric pairing. In addition to these classical cases there are the finite number of exceptional groups. Amazingly enough, motivated by questions in physics, much interest centres around the group E8 and its subgroups. For these applications it does not suffice to consider only the classical groups. Thus, while often first doing the case of SU(n) or more generally of the classical groups, we shall extend our discussions to the general semi-simple group. Also, we shall spend a good deal of time considering elliptically fibered manifolds of the simplest type, namely, elliptic curves
Does size matter? : disentangling consumers' bundling preferences
Manoj K. Agarwal; Frambach, Ruud T.; Stremersch, Stefan
2000-01-01
Previous marketing literature has focused to a large extent on the effect of bundle characteristics on a consumer’s decision to buy a (fixed) bundle in a non-competitive setting. This study extends this narrow focus in four major ways. First, the authors address bundles that are customizable. Second, they distinguish between a consumer’s decision of whether to bundle (bundle choice) and the decision of how many goods or services to include in a bundle (bundle size). Third, they extend the foc...
Advanced Fuel Bundles for PHWRS
International Nuclear Information System (INIS)
The fuel used by NPCIL presently is natural uranium dioxide in the form of 19- element fuel bundles for 220 MWe PHWRs and 37-element fuel bundles for the TAPP-3&4 540 MWe units. The new 700 MWe PHWRs also use 37-element fuel bundles. These bundles are of short 0.5 m length of circular geometry. The cladding is of collapsible type made of Zircaloy-4 material. PHWRs containing a string of short length fuel bundles and the on-power refueling permit flexibility in using different advanced fuel designs and in core fuel management schemes. Using this flexibility, alternative fuel concepts are tried in Indian PHWRs. The advances in PHWR fuel designs are governed by the desire to use resources other than uranium, improve fuel economics by increasing fuel burnup and reduce overall spent nuclear fuel waste and improve reactor safety. The rising uranium prices are leading to a relook into the Thorium based fuel designs and reprocessed Uranium based and Plutonium based MOX designs and are expected to play a major role in future. The requirement of synergism between different type of reactors also plays a role. Increase in fuel burnup beyond 15 000 MW∙d/TeU in PHWRs, using higher fissile content materials like slightly enriched uranium, Mixed Oxide and Thorium Oxide in place of natural uranium in fuel elements, was studied many PHWR operating countries. The work includes reactor physics studies and test irradiation in research reactors and power reactors. Due to higher fissile content these bundles will be capable of delivering higher burnup than the natural uranium bundles. In India the fuel cycle flexibility of PHWRs is demonstrated by converting this type of technical flexibility to the real economy by irradiating these different types of advanced fuel materials namely Thorium, MOX, SEU, etc. The paper gives a review of the different advanced fuel design concepts studied for Indian PHWRs. (author)
Cohomology of line bundles: Applications
Blumenhagen, Ralph; Jurke, Benjamin; Rahn, Thorsten; Roschy, Helmut
2012-01-01
Massless modes of both heterotic and Type II string compactifications on compact manifolds are determined by vector bundle valued cohomology classes. Various applications of our recent algorithm for the computation of line bundle valued cohomology classes over toric varieties are presented. For the heterotic string, the prime examples are so-called monad constructions on Calabi-Yau manifolds. In the context of Type II orientifolds, one often needs to compute cohomology for line bundles on finite group action coset spaces, necessitating us to generalize our algorithm to this case. Moreover, we exemplify that the different terms in Batyrev's formula and its generalizations can be given a one-to-one cohomological interpretation. Furthermore, we derive a combinatorial closed form expression for two Hodge numbers of a codimension two Calabi-Yau fourfold.
Principal bundles the classical case
Sontz, Stephen Bruce
2015-01-01
This introductory graduate level text provides a relatively quick path to a special topic in classical differential geometry: principal bundles. While the topic of principal bundles in differential geometry has become classic, even standard, material in the modern graduate mathematics curriculum, the unique approach taken in this text presents the material in a way that is intuitive for both students of mathematics and of physics. The goal of this book is to present important, modern geometric ideas in a form readily accessible to students and researchers in both the physics and mathematics communities, providing each with an understanding and appreciation of the language and ideas of the other.
Exploring Bundling Theory with Geometry
Eckalbar, John C.
2006-01-01
The author shows how instructors might successfully introduce students in principles and intermediate microeconomic theory classes to the topic of bundling (i.e., the selling of two or more goods as a package, rather than separately). It is surprising how much students can learn using only the tools of high school geometry. To be specific, one can…
Bundled Discounts and EC Judicial Review
Christian Roques
2008-01-01
The Community Courts' case law is rich with cases relating to tying or bundling practices in their classical economic form. However, the same cannot be said for the second acceptance of bundled discounts.
Failure properties of fiber bundle models
Pradhan, Srutarshi; Chakrabarti, Bikas K.
2003-01-01
We study the failure properties of fiber bundles when continuous rupture goes on due to the application of external load on the bundles. We take the two extreme models: equal load sharing model (democratic fiber bundles) and local load sharing model. The strength of the fibers are assumed to be distributed randomly within a finite interval. The democratic fiber bundles show a solvable phase transition at a critical stress (load per fiber). The dynamic critical behavior is obtained analyticall...
Bundling Information Goods: Pricing, Profits, and Efficiency
Yannis Bakos; Erik Brynjolfsson
1999-01-01
We study the strategy of bundling a large number of information goods, such as those increasingly available on the Internet, and selling them for a fixed price. We analyze the optimal bundling strategies for a multiproduct monopolist, and we find that bundling very large numbers of unrelated information goods can be surprisingly profitable. The reason is that the law of large numbers makes it much easier to predict consumers' valuations for a bundle of goods than their valuations for the indi...
Quantum principal bundles and corresponding gauge theories
Durdevic, M
1995-01-01
A generalization of classical gauge theory is presented, in the framework of a noncommutative-geometric formalism of quantum principal bundles over smooth manifolds. Quantum counterparts of classical gauge bundles, and classical gauge transformations, are introduced and investigated. A natural differential calculus on quantum gauge bundles is constructed and analyzed. Kinematical and dynamical properties of corresponding gauge theories are discussed.
Strategic and welfare implications of bundling
DEFF Research Database (Denmark)
Martin, Stephen
1999-01-01
A standard oligopoly model of bundling shows that bundling by a firm with a monopoly over one product has a strategic effect because it changes the substitution relationships between the goods among which consumers choose. Bundling in appropriate proportions is privately profitable, reduces rivals...
On Volumes of Arithmetic Line Bundles
Yuan, Xinyi
2008-01-01
We show an arithmetic generalization of the recent work of Lazarsfeld-Mustata which uses Okounkov bodies to study linear series of line bundles. As applications, we derive a log-concavity inequality on volumes of arithmetic line bundles and an arithmetic Fujita approximation theorem for big line bundles.
Simplicial principal bundles in parametrized spaces
Roberts, David M
2012-01-01
In this paper, motivated by recent interest in higher gauge theory, we prove that the fiberwise geometric realization functor takes a certain class of simplicial principal bundles in a suitable category of spaces over a fixed space $B$ to fiberwise principal bundles. As an application we show that the fiberwise geometric realization of the universal simplicial principal bundle for a simplicial group $G$ in the category of spaces over $B$ gives rise to a fiberwise principal bundle with structure group $|G|$. An application to classifying theory for fiberwise principal bundles is described.
Multipath packet switch using packet bundling
DEFF Research Database (Denmark)
Berger, Michael Stubert
The basic concept of packet bundling is to group smaller packets into larger packets based on, e.g., quality of service or destination within the packet switch. This paper presents novel applications of bundling in packet switching. The larger packets created by bundling are utilized to extend...... switching capacity by use of parallel switch planes. During the bundling operation, packets will experience a delay that depends on the actual implementation of the bundling and scheduling scheme. Analytical results for delay bounds and buffer size requirements are presented for a specific scheduling...
Model of turbine blades bundles
Czech Academy of Sciences Publication Activity Database
Půst, Ladislav; Pešek, Luděk
Prague : Institute of Thermomechanics, Academy of Sciences of the Czech Republic, v. v. i., 2013 - (Zolotarev, I.), s. 467-477 ISBN 978-80-87012-47-5. ISSN 1805-8256. [Engineering Mechanics 2013 /19./. Svratka (CZ), 13.05.2013-16.05.2013] R&D Projects: GA ČR GA101/09/1166 Institutional support: RVO:61388998 Keywords : free and forced vibrations * eigenmodes * mathematical model * bundle of blades Subject RIV: BI - Acoustics
Model of turbine blades bundles
Czech Academy of Sciences Publication Activity Database
Půst, Ladislav; Pešek, Luděk
Praha : Insitute of Thermomechanics ASCR, v. v. i., 2013 - (Zolotarev, I.). s. 125-126 ISBN 978-80-87012-46-8. ISSN 1805-8248. [Engineering Mechanics 2013 /19./. 13.05.2013-16.05.2013, Svratka] R&D Projects: GA ČR GA101/09/1166 Institutional support: RVO:61388998 Keywords : free and forced vibrations * eigenmodes * bundle of blades Subject RIV: BI - Acoustics
Competitive nonlinear pricing and bundling
Armstrong, Mark; Vickers, John
2006-01-01
We examine the impact of multiproduct nonlinear pricing on profit, consumer surplus and welfare in a duopoly. When consumers buy all their products from one firm (the one-stop shopping model), nonlinear pricing leads to higher profit and welfare, but often lower consumer surplus, than linear pricing. By contrast, in a unit-demand model where consumers may buy one product from one firm and another product from another firm, bundling generally acts to reduce profit and welfare and to boost cons...
Quantum bundles and their symmetries
International Nuclear Information System (INIS)
Wave functions in the domain of observables such as the Hamiltonian are not always smooth functions on the classical configuration space Q. Rather, they are often best regarded as functions on a G bundle EG over Q or as sections of an associated bundle. If H is a classical group which acts on Q, its quantum version HG, which acts on EG, is not always H, but an extension of H by G. A powerful and physically transparent construction of EG and HG, where G = U(1) and H1(Q,Z) = 0, has been developed using the path space P. (P consists of paths on Q from a fixed point). In this paper the authors show how to construct EG and HG when G is U(1) or U(1) x π1(Q) and there is no restriction on H1(Q,Z). The method is illustrated with concrete examples, such as a system of charges and monopoles. The method is illustrated with concrete examples, such as a system of charges and monopoles. The authors argue also that P is a sort of superbundle from which a large variety of bundles can be obtained by imposing suitable equivalence relations
Photonic bandgap fiber bundle spectrometer
Hang, Qu; Syed, Imran; Guo, Ning; Skorobogatiy, Maksim
2010-01-01
We experimentally demonstrate an all-fiber spectrometer consisting of a photonic bandgap fiber bundle and a black and white CCD camera. Photonic crystal fibers used in this work are the large solid core all-plastic Bragg fibers designed for operation in the visible spectral range and featuring bandgaps of 60nm - 180nm-wide. 100 Bragg fibers were chosen to have complimentary and partially overlapping bandgaps covering a 400nm-840nm spectral range. The fiber bundle used in our work is equivalent in its function to a set of 100 optical filters densely packed in the area of ~1cm2. Black and white CCD camera is then used to capture spectrally "binned" image of the incoming light at the output facet of a fiber bundle. To reconstruct the test spectrum from a single CCD image we developed an algorithm based on pseudo-inversion of the spectrometer transmission matrix. We then study resolution limit of this spectroscopic system by testing its performance using spectrally narrow test peaks (FWHM 5nm-25nm) centered at va...
Quadratic bundle and nonlinear equations
International Nuclear Information System (INIS)
The paper is aimed at giving an exhaustive description of the nonlinear evolution equations (NLEE), connected with the quadratic bundle (the spectral parameter lambda, which enters quadratically into the equations) and at describing Hamiltonian structure of these equations. The equations are solved through the inverse scattering method (ISM). The basic formulae for the scattering problem are given. The spectral expansion of the integrodifferential operator is used so that its eigenfunctions are the squared solutions of the equation. By using the notions of Hamiltonian structure hierarchy and gauge transformations it is shown how to single out physically interesting NLEE
Static stress analysis of CANFLEX fuel bundles
International Nuclear Information System (INIS)
The static stress analysis of CANFLEX bundles is performed to evaluate the fuel structural integrity during the refuelling service. The structure analysis is carried out by predicting the drag force, stress and displacements of the fuel bundle. By the comparison of strength tests and analysis results, the displacement values are well agreed within 15%. The analysis shows that the CANFLEX fuel bundle keep its structural integrity. 24 figs., 6 tabs., 12 refs. (Author) .new
Damping Properties of the Hair Bundle
Baumgart, Johannes; Kozlov, Andrei S.; Risler, Thomas; Hudspeth, A. James
2015-01-01
The viscous liquid surrounding a hair bundle dissipates energy and dampens oscillations, which poses a fundamental physical challenge to the high sensitivity and sharp frequency selectivity of hearing. To identify the mechanical forces at play, we constructed a detailed finite-element model of the hair bundle. Based on data from the hair bundle of the bullfrog's sacculus, this model treats the interaction of stereocilia both with the surrounding liquid and with the liquid in the narrow gaps b...
Tying, Bundling, and Loyalty/Requirement Rebates
Nicholas Economides
2011-01-01
I discuss the impact of tying, bundling, and loyalty/requirement rebates on consumer surplus in the affected markets. I show that the Chicago School Theory of a single monopoly surplus that justifies tying, bundling, and loyalty/requirement rebates on the basis of efficiency typically fails. Thus, tying, bundling, and loyalty/requirement rebates can be used to extract consumer surplus and enhance profit of firms with market power. I discuss the various setups when this occurs.
Bundling and Competition on the Internet
Yannis Bakos; Erik Brynjolfsson
2000-01-01
The Internet has signi.cantly reduced the marginal cost of producing and distributing digital information goods. It also coincides with the emergence of new competitive strategies such as large-scale bundling. In this paper, we show that bundling can create “economies of aggregation” for information goods if their marginal costs are very low, even in the absence of network externalities or economies of scale or scope. We extend the Bakos-Brynjolfsson bundling model (1999) to settings with sev...
Bundling and joint marketing by rival firms
Jeitschko, Thomas D.; Jung, Yeonjei; Kim, Jaesoo
2014-01-01
We study joint marketing arrangements by competing firms who engage in price discrimination between consumers who patronize only one firm (single purchasing) and those who purchase from both competitors (bundle purchasers). Two types of joint marketing are considered. Firms either commit to a component-price that applies to bundle-purchasers and then firms set stand-alone prices for single purchasers; or firms commit to a rebate off their stand alone price that will be applied to bundle-purch...
Statistical Constitutive Equation of Aramid Fiber Bundles
Institute of Scientific and Technical Information of China (English)
熊杰; 顾伯洪; 王善元
2003-01-01
Tensile impact tests of aramid (Twaron) fiber bundles were carried om under high strain rates with a wide range of 0. 01/s～1000/s by using MTS and bar-bar tensile impact apparatus. Based on the statistical constitutive model of fiber bundles, statistical constitutive equations of aramid fiber bundles are derived from statistical analysis of test data at different strain rates. Comparison between the theoretical predictions and experimental data indicates statistical constitutive equations fit well with the experimental data, and statistical constitutive equations of fiber bundles at different strain rates are valid.
Hydraulic characteristics of HANARO fuel bundles
Energy Technology Data Exchange (ETDEWEB)
Cho, S.; Chung, H. J.; Chun, S. Y.; Yang, S. K.; Chung, M. K. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)
1997-12-31
This paper presents the hydraulic characteristics measured by using LDV (Laser Doppler Velocimetry) in subchannels of HANARO, KAERI research reactor, fuel bundle. The fuel bundle consists of 18 axially finned rods with 3 spacer grids, which are arranged in cylindrical configuration. The effects of the spacer grids on the turbulent flow were investigated by the experimental results. Pressure drops for each component of the fuel bundle were measured, and the friction factors of fuel bundle and loss coefficients for the spacer grids were estimated from the measured pressure drops. Implications regarding the turbulent thermal mixing were discussed. Vibration test results measured by using laser vibrometer were presented. 9 refs., 12 figs. (Author)
Extension of holomorphic bundles to the disc (and Serre's Problem on Stein bundles)
Rosay, Jean-Pierre
2006-01-01
We show how to extend some holomorphic bundles with fifer C^2 and base an open set in C, to bundles on the Riemann Sphere, by an extremely simple technique. In particular, it applies to examples of non-Stein bundles constructed by Skoda and Demailly. It gives an example on C, with polynomial transition automorphisms.
Principal Bundles on the Projective Line
Indian Academy of Sciences (India)
V B Mehta; S Subramanian
2002-08-01
We classify principal -bundles on the projective line over an arbitrary field of characteristic ≠ 2 or 3, where is a reductive group. If such a bundle is trivial at a -rational point, then the structure group can be reduced to a maximal torus.
The Verlinde formula for Higgs bundles
Andersen, Jørgen Ellegaard; Pei, Du
2016-01-01
We propose and prove the Verlinde formula for the quantization of the Higgs bundle moduli spaces and stacks for any simple and simply-connected group. This generalizes the equivariant Verlinde formula for the case of $SU(n)$ proposed previously by the second and third author. We further establish a Verlinde formula for the quantization of parabolic Higgs bundle moduli spaces and stacks.
CANFLEX fuel bundle strength tests (test report)
Energy Technology Data Exchange (ETDEWEB)
Chang, Seok Kyu; Chung, C. H.; Kim, B. D.
1997-08-01
This document outlines the test results for the strength tests of the CANFLEX fuel bundle. Strength tests are performed to determine and verify the amount of the bundle shape distortion which is against the side-stops when the bundles are refuelling. There are two cases of strength test; one is the double side-stop test which simulates the normal bundle refuelling and the other is the single side-stop test which simulates the abnormal refuelling. the strength test specification requires that the fuel bundle against the side-stop(s) simulators for this test were fabricated and the flow rates were controlled to provide the required conservative hydraulic forces. The test rig conditions of 120 deg C, 11.2 MPa were retained for 15 minutes after the flow rate was controlled during the test in two cases, respectively. The bundle loading angles of number 13- number 15 among the 15 bundles were 67.5 deg CCW and others were loaded randomly. After the tests, the bundle shapes against the side-stops were measured and inspected carefully. The important test procedures and measurements were discussed as follows. (author). 5 refs., 22 tabs., 5 figs.
CANFLEX fuel bundle strength tests (test report)
International Nuclear Information System (INIS)
This document outlines the test results for the strength tests of the CANFLEX fuel bundle. Strength tests are performed to determine and verify the amount of the bundle shape distortion which is against the side-stops when the bundles are refuelling. There are two cases of strength test; one is the double side-stop test which simulates the normal bundle refuelling and the other is the single side-stop test which simulates the abnormal refuelling. the strength test specification requires that the fuel bundle against the side-stop(s) simulators for this test were fabricated and the flow rates were controlled to provide the required conservative hydraulic forces. The test rig conditions of 120 deg C, 11.2 MPa were retained for 15 minutes after the flow rate was controlled during the test in two cases, respectively. The bundle loading angles of number 13- number 15 among the 15 bundles were 67.5 deg CCW and others were loaded randomly. After the tests, the bundle shapes against the side-stops were measured and inspected carefully. The important test procedures and measurements were discussed as follows. (author). 5 refs., 22 tabs., 5 figs
k-Gerbes, Line Bundles and Anomalies
Ekstrand, C
2000-01-01
We use sets of trivial line bundles for the realization of gerbes. For1-gerbes the structure arises naturally for the Weyl fermion vacuum bundle at afixed time. The Schwinger term is an obstruction in the triviality of a1-gerbe.
k-Gerbes, Line Bundles and Anomalies
International Nuclear Information System (INIS)
We use sets of trivial line bundles for the realization of gerbes. For 1-gerbes the structure arises naturally for the Weyl fermion vacuum bundle at a fixed time. The Schwinger term is an obstruction in the triviality of a 1-gerbe. (author)
k-Gerbes, Line Bundles and Anomalies
Ekstrand, C.
2000-01-01
We use sets of trivial line bundles for the realization of gerbes. For 1-gerbes the structure arises naturally for the Weyl fermion vacuum bundle at a fixed time. The Schwinger term is an obstruction in the triviality of a 1-gerbe.
Heights for line bundles on arithmetic surfaces
Jahnel, Joerg
1995-01-01
For line bundles on arithmetic varieties we construct height functions using arithmetic intersection theory. In the case of an arithmetic surface, generically of genus g, for line bundles of degree g equivalence is shown to the height on the Jacobian defined by the Theta divisor.
Damping Properties of the Hair Bundle
Baumgart, Johannes; Kozlov, Andrei S.; Risler, Thomas; Hudspeth, A. J.
2011-11-01
The viscous liquid surrounding a hair bundle dissipates energy and dampens oscillations, which poses a fundamental physical challenge to the high sensitivity and sharp frequency selectivity of hearing. To identify the mechanical forces at play, we constructed a detailed finite-element model of the hair bundle. Based on data from the hair bundle of the bullfrog's sacculus, this model treats the interaction of stereocilia both with the surrounding liquid and with the liquid in the narrow gaps between the individual stereocilia. The investigation revealed that grouping stereocilia in a bundle dramatically reduces the total drag. During hair-bundle deflections, the tip links potentially induce drag by causing small but very dissipative relative motions between stereocilia; this effect is offset by the horizontal top connectors that restrain such relative movements at low frequencies. For higher frequencies the coupling liquid is sufficient to assure that the hair bundle moves as a unit with a low total drag. This work reveals the mechanical characteristics originating from hair-bundle morphology and shows quantitatively how a hair bundle is adapted for sensitive mechanotransduction.
Fock modules and noncommutative line bundles
Landi, Giovanni
2016-09-01
To a line bundle over a noncommutative space there is naturally associated a Fock module. The algebra of corresponding creation and annihilation operators is the total space algebra of a principal U(1) -bundle over the noncommutative space. We describe the general construction and illustrate it with examples.
Dirac structures and Dixmier-Douady bundles
Alekseev, A
2009-01-01
A Dirac structure on a vector bundle V is a maximal isotropic subbundle E of the direct sum of V with its dual. We show how to associate to any Dirac structure a Dixmier-Douady bundle A, that is, a Z/2Z-graded bundle of C*-algebras with typical fiber the compact operators on a Hilbert space. The construction has good functorial properties, relative to Morita morphisms of Dixmier-Douady bundles. As applications, we show that the `spin' Dixmier-Douady bundle over a compact, connected Lie group (as constructed by Atiyah-Segal) is multiplicative, and we obtain a canonical `twisted Spin-c-structure' on spaces with group valued moment maps.
Bringing the CANFLEX fuel bundle to market
International Nuclear Information System (INIS)
CANFLEX is a 43-element CANDU fuel bundle, under joint development by AECL and KAERI, to facilitate the use of various advanced fuel cycles in CANDU reactors through the provision of enhanced operating margins. The bundle uses two element diameters (13.5 and 11.5 mm ) to reduce element ratings by 20%, and includes the use of critical-heat-flux (CHF) enhancing appendages to increase the minimum CHF ratio or dryout margin of the bundle. Test programs are underway to demonstrate: the irradiation behaviour, hydraulic characteristics and reactor physics properties of the bundle, along with a test program to demonstrate the ability of the bundle to be handled by CANDU-6 fuelling machines. A fuel design manual and safety analysis reports have been drafted, and both analyses, plus discussions with utilities are underway for a demonstration irradiation in a CANDU-6 reactor. (author)
Line bundle embeddings for heterotic theories
Nibbelin, Stefan Groot; Ruehle, Fabian
2016-04-01
In heterotic string theories consistency requires the introduction of a non-trivial vector bundle. This bundle breaks the original ten-dimensional gauge groups E8 × E8 or SO(32) for the supersymmetric heterotic string theories and SO(16) × SO(16) for the non-supersymmetric tachyon-free theory to smaller subgroups. A vast number of MSSM-like models have been constructed up to now, most of which describe the vector bundle as a sum of line bundles. However, there are several different ways of describing these line bundles and their embedding in the ten-dimensional gauge group. We recall and extend these different descriptions and explain how they can be translated into each other.
CANDU fuel bundle skin friction factor
International Nuclear Information System (INIS)
Single-phase, incompressible fluid flow skin friction factor correlations, primarily for CANDU 37-rod fuel bundles, were reviewed. The correlations originated from curve-fits to flow test data, mostly with new fuel bundles in new pressure tubes (flow tubes), without internal heating. Skin friction in tubes containing fuel bundles (noncircular flow geometry) was compared to that in equivalent diameter smooth circular tubes. At Reynolds numbers typical of normal flows in CANDU fuel channels, the skin friction in tubes containing bundles is 8 to 15% higher than in equivalent diameter smooth circular tubes. Since the correlations are based on scattered results from measurements, the skin friction with bundles may be even higher than indicated above. The information permits over- or under-prediction of the skin friction, or choosing an intermediate value of friction, with allowance for surface roughnesses, in thermal-hydraulic analyses of CANDU heat transport systems. (author) 9 refs., 2 figs
Line bundle embeddings for heterotic theories
Nibbelink, Stefan Groot
2016-01-01
In heterotic theories consistency requires the introduction of a non-trivial vector bundle. This bundle breaks the original ten-dimensional gauge groups E_8 x E_8 or SO(32) for the supersymmetric heterotic theories and SO(16) x SO(16) for the non-supersymmetric tachyon-free theory to smaller subgroups. A vast number of MSSM-like models have been constructed up to now, most of which describe the vector bundle as a sum of line bundles. However, there are several different ways of describing these line bundles and their embedding in the ten-dimensional gauge group. We recall and extend these different descriptions and explain how they can be translated into each other.
Canonical singular hermitian metrics on relative logcanonical bundles
Tsuji, Hajime
2010-01-01
This supersedes 0704.0566. We prove the invariance of logarithmic plurigenera for a projective family of KLT pairs and the adjoint line bundle of KLT line bundles. The proof uses the canonical singular hermitian metrics on relative logcanonical bundles.
On Harder–Narasimhan Reductions for Higgs Principal Bundles
Indian Academy of Sciences (India)
Arijit Dey; R Parthasarathi
2005-05-01
The existence and uniqueness of – reduction for the Higgs principal bundles over nonsingular projective variety is shown. We also extend the notion of – reduction for (, )-bundles and ramified -bundles over a smooth curve.
Effect of bundle size on BWR fuel bundle critical power performance
International Nuclear Information System (INIS)
Effect of the bundle size on the BWR fuel bundle critical power performance was studied. For this purpose, critical power tests were conducted with both 6 x 6 (36 heater rods) and 12 x 12 (144 heater rods) size bundles in the GE ATLAS heat transfer test facility located in San Jose, California. All the bundle geometries such as rod diameter, rod pitch and rod space design are the same except size of flow channel. Two types of critical power tests were performed. One is the critical power test with uniform local peaking pattern for direct comparison of the small and large bundle critical power. Other is the critical power test for lattice positions in the bundle. In this test, power of a group of four rods (2 x 2 array) in a lattice region was peaked higher to probe the critical power of that lattice position in the bundle. In addition, the test data were compared to the COBRAG calculations. COBRAG is a detailed subchannel analysis code for BWR fuel bundle developed by GE Nuclear Energy. Based on these comparisons the subchannel model was refined to accurately predict the data obtained in this test program, thus validating the code capability of handling the effects of bundle size on bundle critical power for use in the study of the thermal hydraulic performance of the future advance BWR fuel bundle design. The author describes the experimental portion of the study program
Gauge symmetries and fibre bundles
International Nuclear Information System (INIS)
The matter is organized as follows. After a brief introduction to the concept of gauge invariance and its relationship to determinism, we introduce in chapters 3 and 4 the notion of fibre bundles in the context of a discussion on spinning point particles and Dirac monopoles. Chapter 3 deals with a non relativistic treatment of the spinning particle. The non trivial extension to relativistic spinning particles is dealt with in Chapter 5. The free particle system as well as interactions with external electromagnetic and gravitational fields are discussed in detail. In chapter 5 we also elaborate on a remarkable relationship between the charge-monopole system and the system of a massless particle with spin. The classical description of Yang-Mills particles with internal degrees of freedom, such as isospin or colour, is given in chapter 6. We apply the above in a discussion of the classical scattering of particles off a 't Hooft-Polyakov monopole. In chapter 7 we elaborate on a Kaluza-Klein description of particles with internal degrees of freedom. The canonical formalism and the quantization of most of the preceeding systems are discussed in chapter 8. The dynamical systems given in chapters 3-7 are formulated on group manifolds. The procedure for obtaining the extension to super-group manifolds is briefly discussed in chapter 9. In chapter 10, we show that if a system admits only local Lagrangians for a configuration space Q, then under certain conditions, it admits a global Lagrangian when Q is enlarged to a suitable U(1) bundle over Q. Conditions under which a symplectic form is derivable from a Lagrangian are also found. (orig./HSI)
Preliminary report: NIF laser bundle review
International Nuclear Information System (INIS)
As requested in the guidance memo 1, this committe determined whether there are compelling reasons to recommend a change from the NIF CDR baseline laser. The baseline bundle design based on a tradeoff between cost and technical risk, which is replicated four times to create the required 192 beams. The baseline amplifier design uses bottom loading 1x4 slab and flashlamp cassettes for amplifier maintenance and large vacuum enclosures (2.5m high x 7m wide in cross-section for each of the two spatial filters in each of the four bundles. The laser beams are arranged in two laser bays configured in a u-shape around the target area. The entire bundle review effort was performed in a very short time (six weeks) and with limited resources (15 personnel part-time). This should be compared to the effort that produced the CDR design (12 months, 50 to 100 personnel). This committee considered three alternate bundle configurations (2x2, 4x2, and 4x4 bundles), and evaluated each bundle against the baseline design using the seven requested issues in the guidance memo: Cost; schedule; performance risk; maintainability/operability; hardware failure cost exposure; activation; and design flexibility. The issues were reviewed to identify differences between each alternate bundle configuration and the baseline
Prioritary omalous bundles on Hirzebruch surfaces
Aprodu, Marian; Marchitan, Marius
2016-01-01
An irreducible algebraic stack is called unirational if there exists a surjective morphism, representable by algebraic spaces, from a rational variety to an open substack. We prove unirationality of the stack of prioritary omalous bundles on Hirzebruch surfaces, which implies also the unirationality of the moduli space of omalous H-stable bundles for any ample line bundle H on a Hirzebruch surface (compare with Costa and Miro-Ŕoig, 2002). To this end, we find an explicit description of the duals of omalous rank-two bundles with a vanishing condition in terms of monads. Since these bundles are prioritary, we conclude that the stack of prioritary omalous bundles on a Hirzebruch surface different from P1 ×P1 is dominated by an irreducible section of a Segre variety, and this linear section is rational (Ionescu, 2015). In the case of the space quadric, the stack has been explicitly described by N. Buchdahl. As a main tool we use Buchdahl's Beilinson-type spectral sequence. Monad descriptions of omalous bundles on hypersurfaces in P4, Calabi-Yau complete intersection, blowups of the projective plane and Segre varieties have been recently obtained by A.A. Henni and M. Jardim (Henni and Jardim, 2013), and monads on Hirzebruch surfaces have been applied in a different context in Bartocci et al. (2015).
Singular hermitian metrics on vector bundles
De Cataldo, M A A
1997-01-01
We introduce a notion of singular hermitian metrics (s.h.m.) for holomorphic vector bundles and define positivity in view of $L^2$-estimates. Associated with a suitably positive s.h.m. there is a (coherent) sheaf 0-th kernel of a certain $d''$-complex. We prove a vanishing theorem for the cohomology of this sheaf. All this generalizes to the case of higher rank known results of Nadel for the case of line bundles. We introduce a new semi-positivity notion, $t$-nefness, for vector bundles, establish some of its basic properties and prove that on curves it coincides with ordinary nefness. We particularize the results on s.h.m. to the case of vector bundles of the form $E=F \\otimes L$, where $F$ is a $t$-nef vector bundle and $L$ is a positive (in the sense of currents) line bundle. As applications we generalize to the higher rank case 1) Kawamata-Viehweg Vanishing Theorem, 2) the effective results concerning the global generation of jets for the adjoint to powers of ample line bundles, and 3) Matsusaka Big Theor...
Deformations of the generalised Picard bundle
International Nuclear Information System (INIS)
Let X be a nonsingular algebraic curve of genus g ≥ 3, and let Mξ denote the moduli space of stable vector bundles of rank n ≥ 2 and degree d with fixed determinant ξ over X such that n and d are coprime. We assume that if g = 3 then n ≥ 4 and if g = 4 then n ≥ 3, and suppose further that n0, d0 are integers such that n0 ≥ 1 and nd0 + n0d > nn0(2g - 2). Let E be a semistable vector bundle over X of rank n0 and degree d0. The generalised Picard bundle Wξ(E) is by definition the vector bundle over Mξ defined by the direct image pMξ *(Uξ x pX*E) where Uξ is a universal vector bundle over X x Mξ. We obtain an inversion formula allowing us to recover E from Wξ(E) and show that the space of infinitesimal deformations of Wξ(E) is isomorphic to H1(X, End(E)). This construction gives a locally complete family of vector bundles over Mξ parametrised by the moduli space M(n0,d0) of stable bundles of rank n0 and degree d0 over X. If (n0,d0) = 1 and Wξ(E) is stable for all E is an element of M(n0,d0), the construction determines an isomorphism from M(n0,d0) to a connected component M0 of a moduli space of stable sheaves over Mξ. This applies in particular when n0 = 1, in which case M0 is isomorphic to the Jacobian J of X as a polarised variety. The paper as a whole is a generalisation of results of Kempf and Mukai on Picard bundles over J, and is also related to a paper of Tyurin on the geometry of moduli of vector bundles. (author)
Geometry of quantum principal bundles, 1
Durdevic, M
1995-01-01
A theory of principal bundles possessing quantum structure groups and classical base manifolds is presented. Structural analysis of such quantum principal bundles is performed. A differential calculus is constructed, combining differential forms on the base manifold with an appropriate differential calculus on the structure quantum group. Relations between the calculus on the group and the calculus on the bundle are investigated. A concept of (pseudo)tensoriality is formulated. The formalism of connections is developed. In particular, operators of horizontal projection, covariant derivative and curvature are constructed and analyzed. Generalizations of the first structure equation and of the Bianchi identity are found. Illustrative examples are presented.
Weak equivalence classes of complex vector bundles
Hông-Vân Lê
2006-01-01
For any complex vector bundle Ek of rank k over a manifold Mm with Chern classes ci Î H2i(Mm, Z) and any non-negative integers l1, . . ., lk we show the existence of a positive number p(m, k) and the existence of a complex vector bundle Êk over Mm whose Chern classes are p(m, k) × li × ci Î H2i(Mm, Z). We also discuss a version of this statement for holomorphic vector bundles over projective algebraic manifolds.
Assembly mechanism for nuclear fuel bundles
International Nuclear Information System (INIS)
A description is given of a nuclear power reactor fuel bundle having tie rods fastened to a lower tie plate and passing through openings in the upper tie plate with the assembled bundle secured by rotatable locking sleeves which engage slots provided in the upper tie plate. Pressure exerted by helical springs mounted around each of the fuel rods urge the upper tie plate against the locking sleeves. The bundle may be disassembled after depressing the upper tie plate and rotating the locking sleeves to the unlocked position
Vector supersymmetry in the universal bundle
International Nuclear Information System (INIS)
We present a vector supersymmetry for Witten-type topological gauge theories, and examine its algebra in terms of a superconnection formalism. When covariant constraints on the supercurvature are chosen, a correspondence is established with the universal bundle construction of Atiyah and Singer. The vector supersymmetry represents a certain shift operator in the curvature of the universal bundle, and can be used to generate the hierarchy of observables in these theories. This formalism should lead to the construction of vector supergravity theories, and perhaps to the gravitational analogue of the universal bundle. (orig.)
Bundle duct interaction studies for fuel assemblies
International Nuclear Information System (INIS)
It is known that the wire-wrapped rods and duct in an LMFBR are undergoing a gradual structural distortion from the initially uniform geometry under the combined effects of thermal expansion and irradiation induced swelling and creep. These deformations have a significant effect on flow characteristics, thus causing changes in thermal behavior such as cladding temperature and temperature distribution within a bundle. The temperature distribution may further enhance or retard irradiation induced deformation of the bundle. This report summarizes the results of the continuing effort in investigating the bundle-duct interaction, focusing on the need for the large development plant
Institute of Scientific and Technical Information of China (English)
YU Wei-dong; YAN Hao-jing; Ron Postle; Yang Shouren
2002-01-01
Due to the effects of samples and testing conditions on fibre-bundle tensile behaviour, it is necessary to investigate the relationships between experimental factors and tensile properties for the fibre-bumdle tensile tester (TENSOR). The effects of bundle sample preparation, fibre bundle mass and fibre alignment have been tested. The experimental results indicated that (1) the low damage in combing and no free-end fibres in the cut bundle are most important for the sample preparation; (2) the reasonable bundle mass is 400- 700tex, but the tensile properties measured should bemodified with the bundle mass because a small amount of bundle mass causes the scatter results, while the larger is the bundle mass, the more difficult to comb fibres parallel and to clamp fibre evenly; and (3) the fibre irregular arrangement forms a slack bundle resulting in interaction between fibres, which will affect the reproducibility and accuracy of the tensile testing.
Self-mapping degrees of torus bundles and torus semi-bundles
Sun, Hongbin; Wang, Shicheng; Wu, Jianchun
2010-01-01
Each closed oriented 3-manifold $M$ is naturally associated with a set of integers $D(M)$, the degrees of all self-maps on $M$. $D(M)$ is determined for each torus bundle and torus semi-bundle $M$. The structure of torus semi-bundle is studied in detail. The paper is a part of a project to determine $D(M)$ for all 3-manifolds in Thurston's picture.
In-pool damaged fuel bundle recovery
International Nuclear Information System (INIS)
While preparing to rerack the Oyster Creek Nuclear Generating Station, GPU Nuclear had need to move a damaged fuel bundle. This bundle had no upper tie plate and could not be moved in the normal manner. GPU Nuclear formed a small, dedicated project team to disassemble, package, and move this damaged bundle. The team was composed of key personnel from GPU Nuclear Fuels Projects, OCNGS Operations and Proto-Power/Bisco, a specialty contractor who has fuel bundle reconstitution and rod consolidation experience, remote tooling, underwater video systems and experienced technicians. Proven tooling, clear procedures and a simple approach were important, but the key element was the spirit of teamwork and leadership exhibited by the people involved. In spite of several emergent problems which a task of this nature presents, this small, close knit utility/vendor team completed the work on schedule and within the exposure and cost budgets
In-pool damaged fuel bundle recovery
International Nuclear Information System (INIS)
While preparing to rerack the Oyster Creek Nuclear Generating Station, GPU Nuclear had need to move a damaged fuel bundle. This bundle had no upper tie plate and could not be moved in the normal manner. GPU Nuclear formed a small, dedicated project team to disassemble, package and move this damaged bundle. The team was composed of key personnel from GPU Nuclear Fuels Projects, OCNGS Operations and Proto-Power / Bisco, a specialty contractor who has fuel bundle reconstitution and rod consolidation experience, remote tooling, underwater video systems and experienced technicians. Proven tooling, clear procedures and a simple approach were important, but the key element was the spirit of teamwork and leadership exhibited by the people involved
Nuclear fuel bundle disassembly and assembly tool
International Nuclear Information System (INIS)
A nuclear power reactor fuel bundle is described which has a plurality of tubular fuel rods disposed in parallel array between two transverse tie plates. It is secured against disassembly by one or more locking forks which engage slots in tie rods which position the transverse plates. Springs mounted on the fuel and tie rods are compressed when the bundle is assembled thereby maintaining a continual pressure against the locking forks. Force applied in opposition to the springs permits withdrawal of the locking forks so that one tie plate may be removed, giving access to the fuel rods. An assembly and disassembly tool facilitates removal of the locking forks when the bundle is to be disassembled and the placing of the forks during assembly of the bundle. (U.S.)
Quantum Bundle Description of Quantum Projective Spaces
Ó Buachalla, Réamonn
2012-12-01
We realise Heckenberger and Kolb's canonical calculus on quantum projective ( N - 1)-space C q [ C p N-1] as the restriction of a distinguished quotient of the standard bicovariant calculus for the quantum special unitary group C q [ SU N ]. We introduce a calculus on the quantum sphere C q [ S 2 N-1] in the same way. With respect to these choices of calculi, we present C q [ C p N-1] as the base space of two different quantum principal bundles, one with total space C q [ SU N ], and the other with total space C q [ S 2 N-1]. We go on to give C q [ C p N-1] the structure of a quantum framed manifold. More specifically, we describe the module of one-forms of Heckenberger and Kolb's calculus as an associated vector bundle to the principal bundle with total space C q [ SU N ]. Finally, we construct strong connections for both bundles.
Twin tori for a new bundle divertor
International Nuclear Information System (INIS)
A new bundle divertor system using the straight stagnation axis in toroidal field together with the uniform field along the axis is discussed in detail. We call this type of divertor as the ''muffler divertor'' because of its shape. (author)
Noncommutative principal bundles through twist deformation
Aschieri, Paolo; Pagani, Chiara; Schenkel, Alexander
2016-01-01
We construct noncommutative principal bundles deforming principal bundles with a Drinfeld twist (2-cocycle). If the twist is associated with the structure group then we have a deformation of the fibers. If the twist is associated with the automorphism group of the principal bundle, then we obtain noncommutative deformations of the base space as well. Combining the two twist deformations we obtain noncommutative principal bundles with both noncommutative fibers and base space. More in general, the natural isomorphisms proving the equivalence of a closed monoidal category of modules and its twist related one are used to obtain new Hopf-Galois extensions as twists of Hopf-Galois extensions. A sheaf approach is also considered, and examples presented.
Crosstalk analysis of carbon nanotube bundle interconnects
Zhang, Kailiang; Tian, Bo; Zhu, Xiaosong; WANG, FANG; Wei, Jun
2012-01-01
Carbon nanotube (CNT) has been considered as an ideal interconnect material for replacing copper for future nanoscale IC technology due to its outstanding current carrying capability, thermal conductivity, and mechanical robustness. In this paper, crosstalk problems for single-walled carbon nanotube (SWCNT) bundle interconnects are investigated; the interconnect parameters for SWCNT bundle are calculated first, and then the equivalent circuit has been developed to perform the crosstalk analys...
A Geometric Approach to Noncommutative Principal Bundles
Wagner, Stefan
2011-01-01
From a geometrical point of view it is, so far, not sufficiently well understood what should be a "noncommutative principal bundle". Still, there is a well-developed abstract algebraic approach using the theory of Hopf algebras. An important handicap of this approach is the ignorance of topological and geometrical aspects. The aim of this thesis is to develop a geometrically oriented approach to the noncommutative geometry of principal bundles based on dynamical systems and the representation theory of the corresponding transformation group.
Parahoric bundles on a compact Riemann surface
Balaji, V
2010-01-01
Let $X$ be a compact Riemann surface of genus $g \\geq 2$. The aim of this paper is to study homomorphisms of certain discrete subgroups of $PSL(2, {\\mathbb R})$ into maximal compact subgroups of semisimple simply connected algebraic groups and relate them to torsors under a Bruhat-Tits group scheme. We also construct the moduli spaces of semistable parahoric bundles. These results generalize the theorem of Mehta and Seshadri on parabolic vector bundles.
Evaluation on BDI of large diameter pin bundles by out-of-pile bundle compression test
International Nuclear Information System (INIS)
Bundle-duct interaction (BDI) in core fuel subassemblies in fast reactors (FRs) is a limiting factor for fuel burnup. Since the large diameter fuel pin is generally believed to be a measure to improve FR fuel performance, the out-of-pile bundle compression test with large diameter pins (φ8.5mm and (φ 10.4mm) was performed to evaluate BDI in these bundles. In the compression test, bundle cross-sectional images (CT images) under BDI condition were obtained by using the X-ray computer tomography. In the main study, the CT images were numerically analyzed to evaluate deformation of the large diameter pin bundle due to BDI. The CT image analysis results revealed that pin-to-duct contact did not occur when the flat-to-flat bundle compression level reached one wire diameter (BDI level of 1dw), which indicates that BDI in large diameter pin bundles was mitigated similarly to the currently used small diameter pin bundles. In addition, the mitigation mechanism for BDI, which delays initiation of pin-to-duct contact, was investigated by using the computer code analysis. The code analysis results showed that cladding oval-distortion acted as a major mitigation mechanism for BDI as in the case of small pin diameter bundles. (author)
Annular burnout data from rod bundle experiments
International Nuclear Information System (INIS)
Burnout data for annular flow in a rod bundle are presented for both transient and steady-state conditions. Tests were performed at the Oak Ridge National Laboratory in the Thermal Hydraulic Test Facility (THTF), a pressurized-water loop containing an electrically heated 64-rod bundle. The bundle configuration is typical of later generation pressurized-water reactors with 17 x 17 fuel arrays. Both axial and radial power profiles are flat. All experiments were carried out in upflow with subcooled inlet conditions, insuring accurate flow measurement. Conditions within the bundle were typical of those which could be encountered during a nuclear reactor loss-of-coolant accident. Level average fluid conditions within the test section were calculated using steady-state mass and energy conservation considerations for the steady-state tests and a transient, homogeneous, equilibrium computer code for the transient tests. Unlike tube dryout, burnout within a rod bundle does not necessarily occur at one distinct axial level. The location of individual rod dryout was determined by scanning rods axially and locating the position where rod superheat increased from approx. =0 to 30 K or greater. Thermocouple instrumentation within the bundle allows the location of dryout to be determined to within approximately +.5 cm for many of the tests
K-Theories for Certain Infinite Rank Bundles
Larrain-Hubach, Andres
2011-01-01
Several authors have recently constructed characteristic classes for classes of infinite rank vector bundles appearing in topology and physics. These include the tangent bundle to the space of maps between closed manifolds, the infinite rank bundles in the families index theorem, and bundles with pseudodifferential operators as structure group. In this paper, we construct the corresponding K-theories for these types of bundles. We develop the formalism of these theories and use their Chern ch...
Effect of left bundle branch block on TIMI frame count
Hatice Tolunay; Ahmet Kasapkara; İsa Öner Yüksel; Nurcan Başar; Ayşe Saatcı Yaşar; Mehmet Bilge
2010-01-01
Aim: Left bundle branch block is an independent risk factorfor cardiac mortality. In this study we aimed to evaluatecoronary blood flow with TIMI frame count in patients with left bundle branch block and angiographically proven normal coronary arteries.Materials and methods: We retrospectively studied 17 patients with left bundle branch block and as a control group 16 patients without left bundle branch block. All patientshad angiographically proven normal coronary arteries.Left bundle branch...
Product-bundling and Incentives for Merger and Strategic Alliance
Sue Mialon
2009-01-01
This paper analyzes firms' choice between a merger and a strategic alliance in bundling their product with other complementary products. We consider a framework in which firms can improve profits only from product-bundling. While mixed bundling is not profitable, pure bundling is because pure bundling reduces consumers' choices, and thus softens competition among firms. Firms benefit the most from this reduced competition if they form an alliance. Firms do not gain as much from a merger becau...
Mechanism of Actin Filament Bundling by Fascin
Energy Technology Data Exchange (ETDEWEB)
Jansen, Silvia; Collins, Agnieszka; Yang, Changsong; Rebowski, Grzegorz; Svitkina, Tatyana; Dominguez, Roberto (UPENN); (UPENN-MED)
2013-03-07
Fascin is the main actin filament bundling protein in filopodia. Because of the important role filopodia play in cell migration, fascin is emerging as a major target for cancer drug discovery. However, an understanding of the mechanism of bundle formation by fascin is critically lacking. Fascin consists of four {beta}-trefoil domains. Here, we show that fascin contains two major actin-binding sites, coinciding with regions of high sequence conservation in {beta}-trefoil domains 1 and 3. The site in {beta}-trefoil-1 is located near the binding site of the fascin inhibitor macroketone and comprises residue Ser-39, whose phosphorylation by protein kinase C down-regulates actin bundling and formation of filopodia. The site in {beta}-trefoil-3 is related by pseudo-2-fold symmetry to that in {beta}-trefoil-1. The two sites are {approx}5 nm apart, resulting in a distance between actin filaments in the bundle of {approx}8.1 nm. Residue mutations in both sites disrupt bundle formation in vitro as assessed by co-sedimentation with actin and electron microscopy and severely impair formation of filopodia in cells as determined by rescue experiments in fascin-depleted cells. Mutations of other areas of the fascin surface also affect actin bundling and formation of filopodia albeit to a lesser extent, suggesting that, in addition to the two major actin-binding sites, fascin makes secondary contacts with other filaments in the bundle. In a high resolution crystal structure of fascin, molecules of glycerol and polyethylene glycol are bound in pockets located within the two major actin-binding sites. These molecules could guide the rational design of new anticancer fascin inhibitors.
International Nuclear Information System (INIS)
PNC has been developing a computer code 'BAMBOO' to analyze the wire spaced FBR fuel pin bundle deformation under the BDI (Bundle Duct Interaction) condition by means of the three dimensional F.E.M. This code analyzes fuel pins' bowing and oval deformations which are dominant deformation behaviors of the fuel pin bundle under the BDI condition. In this study the 'BAMBOO' code is validated on the out-of-pile compression test of the FBR bundle (compression test) by comparing the results of the code analysis with the compression test results, and the highly irradiated (≥2.1x1027 n/m2, E > 0.1 MeV) bundle deformation behaviors are investigated from the viewpoint of the similarity to those in the compression test based on the analytical results of the code. (1) The calculated pin-to-duct minimum clearances as a function of the BDI levels in the compression test analysis agree with the experimental values evaluated from the CT image analysis of the bundle cross-section in the compression test within ±0.2 mm. And the calculated values of the fuel pins' oval deformations agree with the experimental values based on the pin diameter measurements done after the compression test within ±0.05 mm. (2) By comparing the irradiation induced bundle deformation with the bundle deformation in the compression test based on the code analysis, it is confirmed that the changes of the pin-to-duct minimum clearances with the BDI levels show equivalent trends between the both bundle deformations. And in this code analysis of the irradiation induced bundle deformation, contact loads between the fuel pins and the pacer wires are extremely small (below 10 kgf) even at about 3 dw of the BDI level compared to those in the compression test analysis. (J.P.N.)
NIF laser bundle review. Final report
International Nuclear Information System (INIS)
We performed additional bundle review effort subsequent to the completion of the preliminary report and are revising our original recommendations. We now recommend that the NIF baseline laser bundle size be changed to the 4x2 bundle configuration. There are several 4x2 bundle configurations that could be constructed at a cost similar to that of the baseline 4x12 (from $11M more to about $11M less than the baseline; unescalated, no contingency) and provide significant system improvements. We recommend that the building cost estimates (particularly for the in-line building options) be verified by an architect/engineer (A/E) firm knowledgeable about building design. If our cost estimates of the in-line building are accurate and therefore result in a change from the baseline U-shaped building layout, the acceptability of the in-line configuration must be reviewed from an operations viewpoint. We recommend that installation, operation, and maintenance of all laser components be reviewed to better determine the necessity of aisles, which add to the building cost significantly. The need for beam expansion must also be determined since it affects the type of bundle packing that can be used and increases the minimum laser bay width. The U-turn laser architecture (if proven viable) offers a reduction in building costs since this laser design is shorter than the baseline switched design and requires a shorter laser bay
Turbulent flow through two asymmetric rod bundles
International Nuclear Information System (INIS)
Measurements of the mean velocity, of the wall shear stresses, and of the turbulence have been performed in four wall subchannels of rod bundles of four parallel rods enclosed in a rectangular channel. The pitch-to-diameter ratio was P/D=1.148 and the wall-to-diameter ratios ranged from 1.045 to 1.252. The full Reynolds stress tensor has been determined by hot-wire technique. The results of the turbulences intensities show that the flow through rod bundles differs widely from flow through circular tubes. More sophisticated analytical tools than presently available are required to predict turbulent flow through rod bundles with sufficient accuracy
Assembly mechanism for nuclear fuel bundles
International Nuclear Information System (INIS)
In a nuclear power reactor fuel bundle having tie rods fastened to a lower tie plate and passing through openings in the upper tie plate, the assembled bundle is secured by locking lugs fixed to rotatable locking sleeves which engage the upper tie plate. Pressure exerted by helical springs mounted around each of the tie rods urge retaining lugs fixed to a retaining sleeve associated with respective tie rods into a position with respect to the locking sleeve to prevent accidental disengagement of the upper plate from the locking lugs. The bundle may be disassembled by depressing the retaining sleeves and rotating the locking lugs to the disengaged position, and then removing the upper tie plate
Porous Silicon and Denim Fiber Bundle Characterization
Deuro, Randi Ellen
My thesis research aims to characterize and exploit materials in an efficient, rapid, non-destructive manner. Part I of this document summarizes my research on porous silicon (pSi) design, fabrication, and surface modification for use as a novel chemical sensor. The optimization of fabrication process parameters (etching time, etching solution, electrode shape, and the fixing process) on pSi photoluminescence (PL) is presented. I have also investigated the effects of analyte vapors (acetonitrile, toluene, methanol, acetone) on the pSi PL and surface chemistry using luminescence and Fourier-transform infrared (FT-IR) spectroscopy and microscopy methods. The mechanism and benefits of one method of pSi surface modification and protection (ultraviolet (UV) hydrosilylation) will also be presented. Finally, high thorough-put methods of pSi sensor production are described. In Part II of this document, I introduce a novel technique for analyzing and discriminating among denim fiber bundles. An investigation into the benefits of luminescence-based multispectral imaging (LMSI) for denim fiber bundle identification has been conducted. I explore the power of nitromethane (CH 3NO2) based quenching in fiber bundle classification and identify the quenching mechanism. The luminescence spectra (450 - 850 nm) and images from the denim fiber bundles were obtained while exciting at 325 nm or 405 nm. Here, LMSI data were recorded in < 10 s and subsequently assessed by principal component analysis (PCA) and rendered red, green, blue (RGB) component histograms. The results show that LMSI data can be used to rapidly and uniquely classify all the fiber bundle types studied in this research. These non-destructive techniques eliminate extensive sample preparation and allow for rapid multispectral image collection, analysis, and assessment. The quenching data also revealed that the dye molecules within the individual fiber bundles exhibited dramatically different accessibilities to CH 3NO2.
Bundling in semiflexible polymers: A theoretical overview.
Benetatos, Panayotis; Jho, YongSeok
2016-06-01
Supramolecular assemblies of polymers are key modules to sustain the structure of cells and their function. The main elements of these assemblies are charged semiflexible polymers (polyelectrolytes) generally interacting via a long(er)-range repulsion and a short(er)-range attraction. The most common supramolecular structure formed by these polymers is the bundle. In the present paper, we critically review some recent theoretical and computational advances on the problem of bundle formation, and point a few promising directions for future work. PMID:26813628
A bundle of sticks in my garden
Farran, Sue
2012-01-01
The English law of property is often described as a ‘bundle of sticks’ in which each ‘stick’ represents a particular right. Gardens challenge these rights and wreak havoc on the ‘bundle of sticks’. This paper looks at the twenty-first century manifestations of community engagement with ground and explores how ‘gardening’ is undermining concepts of ownership, possession and management of land and how the fence between what is private and what is public is being encroached and challenged by com...
Characteristic classes of quantum principal bundles
Durdevic, M
1995-01-01
A noncommutative-geometric generalization of classical Weil theory of characteristic classes is presented, in the conceptual framework of quantum principal bundles. A particular care is given to the case when the bundle does not admit regular connections. A cohomological description of the domain of the Weil homomorphism is given. Relations between universal characteristic classes for the regular and the general case are analyzed. In analogy with classical geometry, a natural spectral sequence is introduced and investigated. The appropriate counterpart of the Chern character is constructed, for structures admitting regular connections. Illustrative examples and constructions are presented.
TRIGA spent fuel bundles safe storage
Energy Technology Data Exchange (ETDEWEB)
Negut, G.; Covaci, St. [Institute for Nuclear Research, Research Reactor Dept., Pitesti (Romania); Prisecaru, I.; Dupleac, D. [Bucharest Univ. Politehnica, Power and Nuclear Engineering Dept., Bucharest (Romania)
2007-07-01
TRIGA-SSR is a steady state research and material test reactor that has been in operation since 1980. The original TRIGA fuel was HEU (highly enriched uranium) with a U{sup 235} enrichment of 93 per cent. Almost all TRIGA HEU fuel bundles are now burned-up. Part of the spent fuel was loaded and transferred to US, in a Romania - DOE arrangement. The rest of the TRIGA fuel bundles have to be temporarily stored in the TRIGA facility. As the storage conditions had to be established with caution, neutron and thermal hydraulic evaluations of the storage conditions were required. Some criticality evaluations were made based on the SAR (Safety Analysis Report) data. Fuel constant axial temperature approximation effect is usual for criticality computations. TRIGA-SSR fuel bundle geometry and materials model for SCALE5-CSAS module allows the introduction of a fuel temperature dependency for the entire fuel active height, using different materials for each fuel bundle region. Previous RELAP5 thermal hydraulic computations for an axial and radial power distribution in the TRIGA fuel pin were done. Fuel constant temperature approximation overestimates pin factors for every core operating at high temperatures. From the thermal hydraulic point of view the worst condition of the storage grid occurs when the transfer channel is accidentally emptied of water from the pool, or the bundle is handled accidentally to remain in air. All the residual heat from the bundles has to be removed without fuel overheating and clad failure. RELAP5 computer code for residual heat removal was used in the assessment of residual heat removal. We made a couple of evaluations of TRIGA bundle clad temperatures in air cooling conditions, with different residual heat levels. The criticality computations have shown that the spent TRIGA fuel bundles storage grid is strongly sub-critical with k(eff) = 0.5951. So, there is no danger for a criticality accident for this storage grid type. The assessment is done
Scaling Shift in Multicracked Fiber Bundles
Manca, Fabio; Giordano, Stefano; Palla, Pier Luca; Cleri, Fabrizio
2014-12-01
Bundles of fibers, wires, or filaments are ubiquitous structures in both natural and artificial materials. We investigate the bundle degradation induced by an external damaging action through a theoretical model describing an assembly of parallel fibers, progressively damaged by a random population of cracks. Fibers in our model interact by means of a lateral linear coupling, thus retaining structural integrity even after substantial damage. Monte Carlo simulations of the Young's modulus degradation for increasing crack density demonstrate a remarkable scaling shift between an exponential and a power-law regime. Analytical solutions of the model confirm this behavior, and provide a thorough understanding of the underlying physics.
Safe Harbors for Quantity Discounts and Bundling
Dennis W. Carlton; Michael Waldman
2008-01-01
The courts and analysts continue to struggle to articulate safe harbors for a wide variety of common business pricing practices in which either a single product is sold at a discount if purchased in bulk or in which multiple products are bundled together at prices different from the ones that would emerge if the products were purchased separately. The phenomenon of tying in which the sale of one product is conditioned on the purchase of another is closely related to bundling. Its analysis rel...
TRIGA spent fuel bundles safe storage
International Nuclear Information System (INIS)
TRIGA-SSR is a steady state research and material test reactor that has been in operation since 1980. The original TRIGA fuel was HEU (highly enriched uranium) with a U235 enrichment of 93 per cent. Almost all TRIGA HEU fuel bundles are now burned-up. Part of the spent fuel was loaded and transferred to US, in a Romania - DOE arrangement. The rest of the TRIGA fuel bundles have to be temporarily stored in the TRIGA facility. As the storage conditions had to be established with caution, neutron and thermal hydraulic evaluations of the storage conditions were required. Some criticality evaluations were made based on the SAR (Safety Analysis Report) data. Fuel constant axial temperature approximation effect is usual for criticality computations. TRIGA-SSR fuel bundle geometry and materials model for SCALE5-CSAS module allows the introduction of a fuel temperature dependency for the entire fuel active height, using different materials for each fuel bundle region. Previous RELAP5 thermal hydraulic computations for an axial and radial power distribution in the TRIGA fuel pin were done. Fuel constant temperature approximation overestimates pin factors for every core operating at high temperatures. From the thermal hydraulic point of view the worst condition of the storage grid occurs when the transfer channel is accidentally emptied of water from the pool, or the bundle is handled accidentally to remain in air. All the residual heat from the bundles has to be removed without fuel overheating and clad failure. RELAP5 computer code for residual heat removal was used in the assessment of residual heat removal. We made a couple of evaluations of TRIGA bundle clad temperatures in air cooling conditions, with different residual heat levels. The criticality computations have shown that the spent TRIGA fuel bundles storage grid is strongly sub-critical with k(eff) = 0.5951. So, there is no danger for a criticality accident for this storage grid type. The assessment is done for
Impact of bundle deformation on CHF: ASSERT-PV assessment of extended burnup Bruce B bundle G85159W
International Nuclear Information System (INIS)
This paper presents a subchannel thermalhydraulic analysis of the effect on critical heat flux (CHF) of bundle deformation such as element bow and diametral creep. The bundle geometry is based on the post-irradiation examination (PIE) data of a single bundle from the Bruce B Nuclear Generating Station, Bruce B bundle G85159W, which was irradiated for more than two years in the core during reactor commissioning. The subchannel code ASSERT-PV IST is used to assess changes in CHF and dryout power due to bundle deformation, compared to the reference, undeformed bundle. (author)
Abelian conformal field theory and determinant bundles
DEFF Research Database (Denmark)
Andersen, Jørgen Ellegaard; Ueno, K.
2007-01-01
Following [10], we study a so-called bc-ghost system of zero conformal dimension from the viewpoint of [14, 16]. We show that the ghost vacua construction results in holomorphic line bundles with connections over holomorphic families of curves. We prove that the curvature of these connections are...
Optimization of a bundle divertor for FED
International Nuclear Information System (INIS)
Optimal double-T bundle divertor configurations have been obtained for the Fusion Engineering Device (FED). On-axis ripple is minimized, while satisfying a series of engineering constraints. The ensuing non-linear optimization problem is solved via a sequence of quadratic programming subproblems, using the VMCON algorithm. The resulting divertor designs are substantially improved over previous configurations
Capacity efficiency of recovery request bundling
DEFF Research Database (Denmark)
Ruepp, Sarah Renée; Dittmann, Lars; Berger, Michael Stübert; Stidsen, Thomas Riis; Lagakos, Stephen; Perlovsky, Leonid; Jha, Manoi; Covaci, Brindusa; Zaharim, Azarni; Mastorakis, Nikos
2010-01-01
This paper presents a comparison of recovery methods in terms of capacity efficiency. In particular, a method where recovery requests are bundled towards the destination (Shortcut Span Protection) is evaluated against traditional recovery methods. Our simulation results show that Shortcut Span Pr...... Protection uses more capacity than the unbundled related methods, but this is compensated by easier control and management of the recovery actions....
Line bundles on moduli and related spaces
Huebschmann, Johannes
2009-01-01
Let G be a Lie goup, let M and N be smooth connected G-manifolds, let f be a smooth G-map from M to N, and let P denote the fiber of f. Given a closed and equivariantly closed relative 2-form for f with integral periods, we construct the principal G-circle bundles with connection on P having the given relative 2-form as curvature. Given a compact Lie group K, a biinvariant Riemannian metric on K, and a closed Riemann surface S of genus s, when we apply the construction to the particular case where f is the familiar relator map from a product of 2s copies of K to K we obtain the principal K-circle bundles on the associated extended moduli spaces which, via reduction, then yield the corresponding line bundles on possibly twisted moduli spaces of representations of the fundamental group of S in K, in particular, on moduli spaces of semistable holomorphic vector bundles or, more precisely, on a smooth open stratum when the moduli space is not smooth. The construction also yields an alternative geometric object, d...
Bundle Gerbes Applied to Quantum Field Theory
Carey, A L; Murray, M; Carey, Alan; Mickelsson, Jouko; Murray, Michael
2000-01-01
This paper reviews recent work on a new geometric object called a bundle gerbe and discusses some new examples arising in quantum field theory. One application is to an Atiyah-Patodi-Singer index theory construction of the bundle of fermionic Fock spaces parametrized by vector potentials in odd space dimensions and a proof that this leads in a simple manner to the known Schwinger terms (Mickelsson-Faddeev cocycle) for the gauge group action. This gives an explicit computation of the Dixmier-Douady class of the associated bundle gerbe. The method works also in other cases of fermions in external fields (external gravitational field, for example) provided that the APS theorem can be applied; however, we have worked out the details only in the case of vector potentials. Another example, in which the bundle gerbe curvature plays a role, arises from the WZW model on Riemann surfaces. A further example is the `existence of string structures' question. We conclude by showing how global Hamiltonian anomalies fit with...
Quantum field theories on Hilbert bundles
International Nuclear Information System (INIS)
We investigate whether it is possible to maintain the computational features of QED while avoiding some of its mathematical difficulties by formulating QFTs on Hilber bundles. This encounters two problems: 1) Haag's theorem persists, and 2) admissible fields do not generate motions on the base space. To do the latter, the coupling constant has to be a vector field upon the base space. (orig.)
Assembly mechanism for nuclear fuel bundles
International Nuclear Information System (INIS)
This invention relates to an assembly mechanism for nuclear power reactor fuel bundles using a novel, simple and inexpensive means. The mechanism is readily operable remotely, avoids separable parts and is applicable to fuel assemblies in which the upper tie plate is rigidly mounted on the tie rods which hold it in place. (UK)
Capacity efficiency of recovery request bundling
DEFF Research Database (Denmark)
Ruepp, Sarah Renée; Dittmann, Lars; Berger, Michael Stübert; Stidsen, Thomas Riis; Lagakos, Stephen; Perlovsky, Leonid; Jha, Manoi; Covaci, Brindusa; Zaharim, Azarni; Mastorakis, Nikos
2010-01-01
This paper presents a comparison of recovery methods in terms of capacity efficiency. In particular, a method where recovery requests are bundled towards the destination (Shortcut Span Protection) is evaluated against traditional recovery methods. Our simulation results show that Shortcut Span...
Riemann Surfaces: Vector Bundles, Physics, and Dynamics
DEFF Research Database (Denmark)
Sikander, Shehryar
the monodromy with respect to the pulled back connection. The formula for the representation includes a series with coefficients as iterated integrals. This series is closely related to the cyclotomic version of the Drinfel'd associator. The geodesic flow in the unit the tangent bundle of this Teichmueller...
In-pile test of Qinshan PWR fuel bundle
International Nuclear Information System (INIS)
In-pile test of Qinshan Nuclear Power Plant PWR fuel bundle has been conducted in HWRR HTHP Test loop at CIAE. The test fuel bundle was irradiated to an average burnup of 25000 Mwd/tU. The authors describe the structure of (3 x 3-2) test fuel bundle, structure of irradiation rig, fuel fabrication, irradiation conditions, power and fuel burnup. Some comments on the in-pile performance for fuel bundle, fuel rod and irradiation rig were made
Holomorphic Vector Bundle on Hopf Manifolds with Abelian Fundamental Groups
Institute of Scientific and Technical Information of China (English)
Xiang Yu ZHOU; Wei Ming LIU
2004-01-01
Let X be a Hopf manifolds with an Abelian fundamental group. E is a holomorphic vector bundle of rank r with trivial pull-back to W = Cn - {0}. We prove the existence of a non-vanishing section of L(×) E for some line bundle on X and study the vector bundles filtration structure of E. These generalize the results of D. Mall about structure theorem of such a vector bundle E.
Anatomic Double-Bundle Posterior Cruciate Ligament Reconstruction
Chahla, Jorge; Nitri, Marco; Civitarese, David; Dean, Chase S.; Moulton, Samuel G.; LaPrade, Robert F.
2016-01-01
The posterior cruciate ligament (PCL) is known to be the main posterior stabilizer of the knee. Anatomic single-bundle PCL reconstruction, focusing on reconstruction of the larger anterolateral bundle, is the most commonly performed procedure. Because of the residual posterior and rotational tibial instability after the single-bundle procedure and the inability to restore the normal knee kinematics, an anatomic double-bundle PCL reconstruction has been proposed in an effort to re-create the n...
Existence of vector bundles and global resolutions for singular surfaces
Vezzosi, G; S. SCHROER
2002-01-01
Abstract- We prove two results about vector bundles on singular algebraic surfaces. First, on proper surfaces there are vector bundles of rank two with arbitrarily large second Chern number and fixed determinant. Second, on separated normal surfaces any coherent sheaf is the quotient of a vector bundle. As a consequence, for such surfaces the Quillen K-theory of vector bundles coincides with the Waldhausen K-theory of perfect complexes. Examples show that, on non-separated schemes, usually...
CANFLEX - an advanced fuel bundle for CANDU
International Nuclear Information System (INIS)
The performance of CANDU pressurized heavy-water reactors, in terms of lifetime load factors, is excellent. More than 600 000 bundles containing natural-uranium fuel have been irradiated, with a low defect rate; reactor unavailability due to fuel incidents is typically zero. To maintain and improve CANDU's competitive position, Atomic Energy of Canada Limited (AECL) has an ongoing program comprising design, safety and availability improvements, advanced fuel concepts and schemes to reduce construction time. One key finding is that the introduction of slightly-enriched uranium (SEU, less than 1.5 wt% U-235 in U) offers immediate benefits for CANDU, in terms of fuelling and back-end disposal costs. The use of SEU places more demands on the fuel because of extended burnup, and an anticipated capability to load-follow also adds to the performance requirements. To ensure that the duty-cycle targets for SEU and load-following are achieved, AECL is developing a new fuel bundle, termed CANFLEX (CANdu FLEXible), where flexible refers to the versatility of the bundle with respect to operational and fuel-cycle options. Though the initial purpose of the new 43-element bundle is to introduce SEU into CANDU, CANFLEX is extremely versatile in its application, and is compatible with other fuel cycles of interest: natural uranium in existing CANDU reactors, recycled uranium and mixed-oxides from light-water reactors, and thoria-based fuels. Capability with a variety of fuel cycles is the key to future CANDU success in the international market. The improved performance of CANFLEX, particularly at high burnups, will ensure that the full economic benefits of advanced fuels cycles are achieved. A proof-tested CANFLEX bundle design will be available in 1993 for large-scale commercial-reactor demonstration
Interplanetary Overlay Network Bundle Protocol Implementation
Burleigh, Scott C.
2011-01-01
The Interplanetary Overlay Network (ION) system's BP package, an implementation of the Delay-Tolerant Networking (DTN) Bundle Protocol (BP) and supporting services, has been specifically designed to be suitable for use on deep-space robotic vehicles. Although the ION BP implementation is unique in its use of zero-copy objects for high performance, and in its use of resource-sensitive rate control, it is fully interoperable with other implementations of the BP specification (Internet RFC 5050). The ION BP implementation is built using the same software infrastructure that underlies the implementation of the CCSDS (Consultative Committee for Space Data Systems) File Delivery Protocol (CFDP) built into the flight software of Deep Impact. It is designed to minimize resource consumption, while maximizing operational robustness. For example, no dynamic allocation of system memory is required. Like all the other ION packages, ION's BP implementation is designed to port readily between Linux and Solaris (for easy development and for ground system operations) and VxWorks (for flight systems operations). The exact same source code is exercised in both environments. Initially included in the ION BP implementations are the following: libraries of functions used in constructing bundle forwarders and convergence-layer (CL) input and output adapters; a simple prototype bundle forwarder and associated CL adapters designed to run over an IPbased local area network; administrative tools for managing a simple DTN infrastructure built from these components; a background daemon process that silently destroys bundles whose time-to-live intervals have expired; a library of functions exposed to applications, enabling them to issue and receive data encapsulated in DTN bundles; and some simple applications that can be used for system checkout and benchmarking.
Compactifications of reductive groups as moduli stacks of bundles
DEFF Research Database (Denmark)
Martens, Johan; Thaddeus, Michael
Let G be a reductive group. We introduce the moduli problem of "bundle chains" parametrizing framed principal G-bundles on chains of lines. Any fan supported in a Weyl chamber determines a stability condition on bundle chains. Its moduli stack provides an equivariant toroidal compactification of ...
VECTOR BUNDLE, KILLING VECTOR FIELD AND PONTRYAGIN NUMBERS
Institute of Scientific and Technical Information of China (English)
周建伟
1991-01-01
Let E be a vector bundle over a compact Riemannian manifold M. We construct a natural metric on the bundle space E and discuss the relationship between the killing vector fields of E and M. Then we give a proof of the Bott-Baum-Cheeger Theorem for vector bundle E.
Noncommutative principal torus bundles via parametrised strict deformation quantization
Hannabuss, Keith; Mathai, Varghese
2009-01-01
In this paper, we initiate the study of a parametrised version of Rieffel's strict deformation quantization. We apply it to give a classification of noncommutative principal torus bundles, in terms of parametrised strict deformation quantization of ordinary principal torus bundles. The paper also contains a putative definition of noncommutative non-principal torus bundles.
Laser cutting for dismantling of PHWR fuel bundles
International Nuclear Information System (INIS)
Detailed investigation was carried out on laser cutting of zircaloy-2 PHWR fuel pin bundles. Initially, trials were done to standardize ten parameters for cutting of tie plates to which individual fuel pins are welded in a bundle. Using these parameters, the tie plates were cut into several pieces so that each fuel pin is individually separated out from the bundle. (author)
Geometry of torus bundles in integrable Hamiltonian systems
Lukina, Olga
2008-01-01
Thesis is concerned with global properties of Lagrangian bundles, i.e. symplectic n-torus bundles, as these occur in integrable Hamiltonian systems. It treats obstructions to triviality and concerns with classification of such bundles, as well as with manifestations of global invariants in real-worl
Stability of Picard Bundle Over Moduli Space of Stable Vector Bundles of Rank Two Over a Curve
Indian Academy of Sciences (India)
Indranil Biswas; Tomás L Gómez
2001-08-01
Answering a question of [BV] it is proved that the Picard bundle on the moduli space of stable vector bundles of rank two, on a Riemann surface of genus at least three, with fixed determinant of odd degree is stable.
Productivity and costs of slash bundling in Nordic conditions
Energy Technology Data Exchange (ETDEWEB)
Kaerhae, K.; Vartiamaeki, T. [Metsaeteho Oy, P.O. Box 101, FI-00171 Helsinki (Finland)
2006-12-15
The number of slash bundlers and the volume of slash bundling have been rapidly increasing during the last few years in Finland. However, no comprehensive time or follow-up studies have been carried out on slash bundling technology in Finland or in any other country. Metsateho Oy carried out studies on the productivity and costs of slash bundling in different Nordic recovering conditions. The study methods included both time and follow-up studies. Data were collected during the summer and winter period primarily in Norway spruce (Picea abies L. Karst.) dominated clear cutting sites. The bundling techniques performed by different types of bundler (Fiberpac 370, Timberjack 1490D, Pika RS 2000, Valmet WoodPac) were studied. The average productivity of slash bundling was 18.1 bundles per operating (E{sub 15}, including delays shorter than 15min) hour with the Timberjack 1490D and Fiberpac 370 bundlers in the follow-up study. The operator of the slash bundler had the greatest effect on the productivity of bundling. The prerequisite for increased bundling volumes is a reduction in the costs of the most expensive sub-stage of the bundling supply chain, i.e. bundling itself. This requires improved recovery conditions at bundling sites, increased bundling productivity, larger sized bundles, and the execution of bundling operations in two work shifts using an efficient bundler and effective operator working methods. Implementation of these development measures will bring the bundling supply chain up to a speed that makes it the most competitive supply chain for forest chips in terms of total supply costs for long-distance transportation distances of more than 60km. (author)
Energy Technology Data Exchange (ETDEWEB)
Kaipainen, H.; Seppaenen, V.; Rinne, S.
1996-12-31
The conditions on which the bundling of the harvesting residues from spruce regeneration fellings would become profitable were studied. The calculations showed that one of the most important features was sufficient compaction of the bundle, so that the portion of the wood in the unit volume of the bundle has to be more than 40 %. The tests showed that the timber grab loader of farm tractor was insufficient for production of dense bundles. The feeding and compression device of the prototype bundler was constructed in the research and with this device the required density was obtained.The rate of compaction of the dry spruce felling residues was about 40 % and that of the fresh residues was more than 50 %. The comparison between the bundles showed that the calorific value of the fresh bundle per unit volume was nearly 30 % higher than that of the dry bundle. This means that the treatment of the bundles should be done of fresh felling residues. Drying of the bundles succeeded well, and the crushing and chipping tests showed that the processing of the bundles at the plant is possible. The treatability of the bundles was also excellent. By using the prototype, developed in the research, it was possible to produce a bundle of the fresh spruce harvesting residues, the diameter of which was about 50 cm and the length about 3 m, and the rate of compaction over 50 %. By these values the reduction target of the costs is obtainable
Comparison of ASSERT subchannel code with Marviken bundle data
International Nuclear Information System (INIS)
In this paper ASSERT predictions are compared with the Marviken 6-rod bundle and 36+1 rod bundle. The predictions are presented for two experiments in the 6-rod bundle and four experiments in the 36+1 rod bundle. For low inlet subcooling, the void predictions are in good agreement with the experimental data. For high inlet subcooling, however, the agreement is not as good. This is attributed to the fact that in the high inlet subcooling experiments, single phase turbulent mixing plays a more important role in determining flow conditions in the bundle
Multiwalled carbon nanotube reinforced biomimetic bundled gel fibres.
Kim, Young-Jin; Yamamoto, Seiichiro; Takahashi, Haruko; Sasaki, Naruo; Matsunaga, Yukiko T
2016-08-19
This work describes the fabrication and characterization of hydroxypropyl cellulose (HPC)-based biomimetic bundled gel fibres. The bundled gel fibres were reinforced with multiwalled carbon nanotubes (MWCNTs). A phase-separated aqueous solution with MWCNT and HPC was transformed into a bundled fibrous structure after being injected into a co-flow microfluidic device and applying the sheath flow. The resulting MWCNT-bundled gel fibres consist of multiple parallel microfibres. The mechanical and electrical properties of MWCNT-bundled gel fibres were improved and their potential for tissue engineering applications as a cell scaffold was demonstrated. PMID:27200527
Effectiveness of Hair Bundle Motility as the Cochlear Amplifier
Sul, Bora; Iwasa, Kuni H.
2009-01-01
The effectiveness of hair bundle motility in mammalian and avian ears is studied by examining energy balance for a small sinusoidal displacement of the hair bundle. The condition that the energy generated by a hair bundle must be greater than energy loss due to the shear in the subtectorial gap per hair bundle leads to a limiting frequency that can be supported by hair-bundle motility. Limiting frequencies are obtained for two motile mechanisms for fast adaptation, the channel re-closure mode...
Anatomic Double-Bundle Posterior Cruciate Ligament Reconstruction.
Chahla, Jorge; Nitri, Marco; Civitarese, David; Dean, Chase S; Moulton, Samuel G; LaPrade, Robert F
2016-02-01
The posterior cruciate ligament (PCL) is known to be the main posterior stabilizer of the knee. Anatomic single-bundle PCL reconstruction, focusing on reconstruction of the larger anterolateral bundle, is the most commonly performed procedure. Because of the residual posterior and rotational tibial instability after the single-bundle procedure and the inability to restore the normal knee kinematics, an anatomic double-bundle PCL reconstruction has been proposed in an effort to re-create the native PCL footprint more closely and to restore normal knee kinematics. We detail our technique for an anatomic double-bundle PCL reconstruction using Achilles and anterior tibialis tendon allografts. PMID:27284530
The turbulent flow in rod bundles
International Nuclear Information System (INIS)
Experimental studies have shown that the axial and azimuthal turbulence intensities in the gap regions of rod bundles increase strongly with decreasing rod spacing; the fluctuating velocities in the axial and azimuthal directions have a quasi-periodic behaviour. To determine the origin of this phenomenon, an its characteristics as a function of the geometry and the Reynolds number, an experimental investigation was performed on the turbulent in several rod bundles with different aspect ratios (P/D, W/D). Hot-wires and microsphones were used for the measurements of velocity and wall pressure fluctuations. The data were evaluated to obtain spectra as well as auto and cross correlations. Based on the results, a phenomenological model is presented to explain this phenomenon. By means of the model, the mass exchange between neighbouring subchannels is explained
Reactor application of an improved bundle divertor
International Nuclear Information System (INIS)
A Bundle Divertor was chosen as the impurity control and plasma exhaust system for the beam driven Demonstration Tokamak Hybrid Reactor - DTHR. In the context of a preconceptual design study of the reactor and associated facility a bundle divertor concept was developed and integrated into the reactor system. The overall system was found feasible and scalable for reactors with intermediate torodial field strengths on axis. The important design characteristics are: the overall average current density of the divertor coils is 0.73 kA for each tesla of toroidal field on axis; the divertor windings are made from super-conducting cables supported by steel structures and are designed to be maintainable; the particle collection assembly and auxiliary cryosorption vacuum pump are dual systems designed such that they can be reactivated alterntively to allow for continuous reactor operation; and the power requirement for energizing and operating the divertor is about 5 MW
Venereau polynomials and related fiber bundles
Kaliman, Shulim; ZAIDENBERG, MIKHAIL
2003-01-01
The Venereau polynomials v-n:=y+x^n(xz+y(yu+z^2)), n>= 1, on A4 have all fibers isomorphic to the affine space A3. Moreover, for all n>= 1 the map (v-n, x) : A4 -> A2 yields a flat family of affine planes over A2. In the present note we show that over the punctured plane A2\\0, this family is a fiber bundle. This bundle is trivial if and only if v-n is a variable of the ring C[x][y,z,u] over C[x]. It is an open question whether v1 and v2 are variables of the polynomial ring C[x,y,z,u]. S. Vene...
A fibre bundle formulation of quantum geometry
International Nuclear Information System (INIS)
Quantum geometries whose points are stochastic and serve as seats for quantum space-time excitons are formulated as fibre bundles over base spaces of mean values with a Minkowski or general relativistic structure. The fibres contain the proper wave functions of all exciton states in a given model. The notion of covariance and propagation in quantum space-times constituting such fibre bundles is investigated. Maxwell and Yang-Mills gauge degrees of freedom are introduced by appropriately enlarging the structure group, which in all cases contains phase-space representations of the Poincare group corresponding to the exciton wave function sample space specific to a given model. It is shown that these formulations give rise in a natural manner to certain realizations of the relativistic canonical commutation relations in terms of covariant derivatives involving internal as well as external degrees of freedom of space-time excitons
Heterotic String Compactification and New Vector Bundles
Lin, Hai; Wu, Baosen; Yau, Shing-Tung
2016-07-01
We propose a construction of Kähler and non-Kähler Calabi-Yau manifolds by branched double covers of twistor spaces. In this construction we use the twistor spaces of four-manifolds with self-dual conformal structures, with the examples of connected sum of n {mathbb{P}2}s. We also construct K3-fibered Calabi-Yau manifolds from the branched double covers of the blow-ups of the twistor spaces. These manifolds can be used in heterotic string compactifications to four dimensions. We also construct stable and polystable vector bundles. Some classes of these vector bundles can give rise to supersymmetric grand unified models with three generations of quarks and leptons in four dimensions.
Rod bundle burnout data and correlation comparisons
International Nuclear Information System (INIS)
Rod bundle burnout data from 30 steady-state and 3 transient tests were obtained from experiments performed in the Thermal Hydraulic Test Facility at the Oak Ridge National Laboratory. The tests covered a parameter range relevant to intact core reactor accidents ranging from large break to small break loss-ofcoolant conditions. Instrumentation within the 64-rod test section indicated that burnout occurred over an axial range within the bundle. The distance from the point where the first dry rod was detected to the point where all rods were dry was up to 60 cm in some of the tests. The burnout data should prove useful in developing new correlations for use in reactor thermalhydraulic codes. Evaluation of several existing critical heat flux correlations using the data show that three correlations, the Barnett, Bowring, and Katto correlations, perform similarly and correlate the data better than the Biasi correlation
Client Provider Collaboration for Service Bundling
Directory of Open Access Journals (Sweden)
LETIA, I. A.
2008-04-01
Full Text Available The key requirement for a service industry organization to reach competitive advantages through product diversification is the existence of a well defined method for building service bundles. Based on the idea that the quality of a service or its value is given by the difference between expectations and perceptions, we draw the main components of a frame that aims to support the client and the provider agent in an active collaboration meant to co-create service bundles. Following e3-value model, we structure the supporting knowledge around the relation between needs and satisfying services. We deal with different perspectives about quality through an ontological extension of Value Based Argumentation. The dialog between the client and the provider takes the form of a persuasion whose dynamic object is the current best configuration. Our approach for building service packages is a demand driven approach, allowing progressive disclosure of private knowledge.
Radiological evidence for the triple bundle anterior cruciate ligament.
MacKay, James W; Whitehead, Harry; Toms, Andoni P
2014-10-01
The anterior cruciate ligament (ACL) has traditionally been described as having two bundles--one anteromedial and one posterolateral. This has been challenged by studies proposing the existence of a third, intermediate, bundle with distinct functional significance, an arrangement that has been described in a number of domesticated animal species. No radiological evidence for the triple bundle ACL has previously been described. A prevalence study was carried out on 73 consecutive human knee magnetic resonance (MR) studies to determine the number of visible bundles, excluding individuals with a history of ACL injury or mucoid degeneration. A triple bundle ACL was demonstrated in 15 out of 73 human knees (20.5%, 95% confidence interval 12.9-31.2%). This is the first radiological description of the human triple bundle ACL. There was MR imaging evidence of a triple bundle ACL in approximately one fifth of human knees in this study. PMID:24890455
CHF and flow instability in rod bundles
International Nuclear Information System (INIS)
Data for two very different rod bundles have been analyzed using a new CHF correlation and a crude, but simple, subchannel analysis. The CHF correlation was developed for round uniform tubes and has been shown to accurately predict CHF in nonuniform tubes. The first set of data was for a KWU rod bundle (37 rods) with a heated length of 3.00 m and an O.D. (outside diameter) of 12.9 mm over a range of pressure 70 to 150 bar in upflow. The second set of data was for a 5 x 5 TRIGA rod bundle with a heated length of 0.559 m and 13.75 mm O.D. over a range of pressure of 0.945 to 1.372 bar in downflow. In contrast to the KWU data, the correlation greatly over estimates the CHF values for the TRIGA data. The TRIGA CHF data correlate very well with the variable qsat assuming no mixing, qc,exp = 0.955qsat (stdev = 9.87%). This result strongly suggests that these instabilities, which resulted immediately in CHF, are triggered by the Onset of Flow Instability (OFI) rather than CHF. The wide spread in rod power factors, the low pressure, and the downflow condition all contribute to promoting this type of instability (Ledinegg). The crude subchannel analysis has been compared with calculations of exit conditions of the hot channel using COBRA code. The agreement is fair when the homogeneous equilibrium model is used in the COBRA code. This is expected since the exit of the hot channel is always subcooled. Using Zuber's, along with other, void fraction relations in COBRA yields much lower exit velocities and high positive exit qualities, and, in some cases, convergence difficulties arise. The facts indicate that the bundle has already past the OFI point: which is possible since no CHF calculation was made in these COBRA analyses. (J.P.N)
Interstitial He and Ne in Nanotube Bundles
Stan, G.; Crespi, V. H.; Cole, M. W.; Boninsegni, M.
1998-01-01
We explore the properties of atoms confined to the interstitial regions within a carbon nanotube bundle. We find that He and Ne atoms are of ideal size for physisorption interactions, so that their binding energies are much greater there than on planar surfaces of any known material. Hence high density phases exist at even small vapor pressure. There can result extraordinary anisotropic liquids or crystalline phases, depending on the magnitude of the corrugation within the interstitial channels.
Effective freeness of adjoint line bundles
Heier, Gordon
2001-01-01
In this note we establish a new Fujita-type effective bound for the base point freeness of adjoint line bundles on a compact complex projective manifold of complex dimension $n$. The bound we obtain (approximately) differs from the linear bound conjectured by Fujita only by a factor of the cube root of $n$. As an application, a new effective statement for pluricanonical embeddings is derived.
On Complex Supermanifolds with Trivial Canonical Bundle
Groeger, Josua
2016-01-01
We give an algebraic characterisation for the triviality of the canonical bundle of a complex supermanifold in terms of a certain Batalin-Vilkovisky superalgebra structure. As an application, we study the Calabi-Yau case, in which an explicit formula in terms of the Levi-Civita connection is achieved. Our methods include the use of complex integral forms and the recently developed theory of superholonomy.
Telescope sipping - pinpointing leaking fuel bundles
International Nuclear Information System (INIS)
Given the top priority operators of nuclear power plants assign to safety, even the slightest sign of damage to the fuel assemblies has to be carefully monitored and analyzed. The detection of leaking fuel bundles also plays an important role in ensuring good availability and economy for the plants. ABB Atom has developed a new, highly accurate method, called 'telescope sipping', for identifying defective fuel assemblies. (orig.)
Imperfect Bundling In Public-Private Partnerships
Luciano Greco
2012-01-01
The economic literature on PPPs has generally overlooked agency problems within private consortia. We provide a first contribution in this direction, relying on a simple incomplete contracts framework where a Builder and an Operator set up a Special Purpose Vehicle (SPV) to carry out a contract with the government. Because of incomplete contracts, the bundling of tasks is imperfect, and the SPV ownership structure is the main tool to regulate the power of private incentives. The scope for wel...
Using Advanced Fuel Bundles in CANDU Reactors
International Nuclear Information System (INIS)
Improving the exit fuel burnup in CANDU reactors was a long-time challenge for both bundle designers and performance analysts. Therefore, the 43-element design together with several fuel compositions was studied, in the aim of assessing new reliable, economic and proliferation-resistant solutions. Recovered Uranium (RU) fuel is intended to be used in CANDU reactors, given the important amount of slightly enriched Uranium (~0.96% w/o U235) that might be provided by the spent LWR fuel recovery plants. Though this fuel has a far too small U235 enrichment to be used in LWR's, it can be still used to fuel CANDU reactors. Plutonium based mixtures are also considered, with both natural and depleted Uranium, either for peacefully using the military grade dispositioned Plutonium or for better using Plutonium from LWR reprocessing plants. The proposed Thorium-LEU mixtures are intended to reduce the Uranium consumption per produced MW. The positive void reactivity is a major concern of any CANDU safety assessment, therefore reducing it was also a task for the present analysis. Using the 43-element bundle with a certain amount of burnable poison (e.g. Dysprosium) dissolved in the 8 innermost elements may lead to significantly reducing the void reactivity. The expected outcomes of these design improvements are: higher exit burnup, smooth/uniform radial bundle power distribution and reduced void reactivity. Since the improved fuel bundles are intended to be loaded in existing CANDU reactors, we found interesting to estimate the local reactivity effects of a mechanical control absorber (MCA) on the surrounding fuel cells. Cell parameters and neutron flux distributions, as well as macroscopic cross-sections were estimated using the transport code DRAGON and a 172-group updated nuclear data library. (author)
Uncovering ecosystem service bundles through social preferences.
Directory of Open Access Journals (Sweden)
Berta Martín-López
Full Text Available Ecosystem service assessments have increasingly been used to support environmental management policies, mainly based on biophysical and economic indicators. However, few studies have coped with the social-cultural dimension of ecosystem services, despite being considered a research priority. We examined how ecosystem service bundles and trade-offs emerge from diverging social preferences toward ecosystem services delivered by various types of ecosystems in Spain. We conducted 3,379 direct face-to-face questionnaires in eight different case study sites from 2007 to 2011. Overall, 90.5% of the sampled population recognized the ecosystem's capacity to deliver services. Formal studies, environmental behavior, and gender variables influenced the probability of people recognizing the ecosystem's capacity to provide services. The ecosystem services most frequently perceived by people were regulating services; of those, air purification held the greatest importance. However, statistical analysis showed that socio-cultural factors and the conservation management strategy of ecosystems (i.e., National Park, Natural Park, or a non-protected area have an effect on social preferences toward ecosystem services. Ecosystem service trade-offs and bundles were identified by analyzing social preferences through multivariate analysis (redundancy analysis and hierarchical cluster analysis. We found a clear trade-off among provisioning services (and recreational hunting versus regulating services and almost all cultural services. We identified three ecosystem service bundles associated with the conservation management strategy and the rural-urban gradient. We conclude that socio-cultural preferences toward ecosystem services can serve as a tool to identify relevant services for people, the factors underlying these social preferences, and emerging ecosystem service bundles and trade-offs.
Noncommutative line bundle and Morita equivalence
Jurco, Branislav; Schupp, Peter; Wess, Julius
2001-01-01
Global properties of abelian noncommutative gauge theories based on $\\star$-products which are deformation quantizations of arbitrary Poisson structures are studied. The consistency condition for finite noncommutative gauge transformations and its explicit solution in the abelian case are given. It is shown that the local existence of invertible covariantizing maps (which are closely related to the Seiberg-Witten map) leads naturally to the notion of a noncommutative line bundle with noncommu...
Bundling harvester; Harvennuspuun automaattisen nippukorjausharvesterin kehittaeminen
Energy Technology Data Exchange (ETDEWEB)
Koponen, K. [Eko-Log Oy, Kuopio (Finland)
1997-12-01
The starting point of the project was to design and construct, by taking the silvicultural point of view into account, a harvesting and processing system especially for energy-wood, containing manually driven bundling harvester, automating of the harvester, and automated loading. The equipment forms an ideal method for entrepreneur`s-line harvesting. The target is to apply the system also for owner`s-line harvesting. The profitability of the system promotes the utilisation of the system in both cases. The objectives of the project were: to construct a test equipment and prototypes for all the project stages, to carry out terrain and strain tests in order to examine the usability and durability, as well as the capacity of the machine, to test the applicability of the Eko-Log system in simultaneous harvesting of energy and pulp woods, and to start the marketing and manufacturing of the products. The basic problems of the construction of the bundling harvester have been solved using terrain-tests. The prototype machine has been shown to be operable. Loading of the bundles to form sufficiently economically transportable loads has been studied, and simultaneously, the branch-biomass has been tried to be utilised without loosing the profitability of transportation. The results have been promising, and will promote the profitable utilisation of wood-energy. (orig.)
Nuclear reactor control bundle guide system
International Nuclear Information System (INIS)
Each bundle is formed by several absorbent rods, which are vertically movable and are connected together by a spider to a common axial operating rod, and guide means for the control bundles in their displacement, out of the core; the said means comprise guide boxes containing horizontal plates for discontinuous guiding, at the upper part of the boxes, of absorbent rods positioned in pairs on a radius and individual peripheral absorbent rods of the control bundle. At the lower part of the boxes in a continuous guiding zone, guiding of the absorbent rods positioned in pairs on a radius is effected by association of the horizontal plates for mechanical guiding of the rods, with housings which minimise hydraulic effects by smoothing the coolant flow in the radial direction around the absorbent rods. The hydraulic housings are mounted between the horizontal plates as discontinuous spacers. Pressure differences around each rod are minimised or eliminated and continuous guiding is achieved without affecting the design of the guide boxes, the internal equipment or the pressure vessel. The invention can be applied to PWRs
Adsorption of Argon on Carbon nanotube bundles and its influence on the bundle lattice parameter
International Nuclear Information System (INIS)
We report experimental studies of the adsorption characteristics and structure of both Ar36 and Ar40 on single-wall carbon nanotube bundles. The structural studies make use of the large difference in coherent neutron scattering cross section for the two Ar isotopes to explore the influence of the adsorbate on the nanotube lattice parameter. We observe no dilation of the nanotube lattice with Ar40, and explain the apparent expansion of this lattice upon Ar36 adsorption by the location of the adsorbed Ar atoms on the outer bundle surface
Amplitude death of coupled hair bundles with stochastic channel noise
Kim, Kyung-Joong
2014-01-01
Hair cells conduct auditory transduction in vertebrates. In lower vertebrates such as frogs and turtles, due to the active mechanism in hair cells, hair bundles(stereocilia) can be spontaneously oscillating or quiescent. Recently, the amplitude death phenomenon has been proposed [K.-H. Ahn, J. R. Soc. Interface, {\\bf 10}, 20130525 (2013)] as a mechanism for auditory transduction in frog hair-cell bundles, where sudden cessation of the oscillations arises due to the coupling between non-identical hair bundles. The gating of the ion channel is intrinsically stochastic due to the stochastic nature of the configuration change of the channel. The strength of the noise due to the channel gating can be comparable to the thermal Brownian noise of hair bundles. Thus, we perform stochastic simulations of the elastically coupled hair bundles. In spite of stray noisy fluctuations due to its stochastic dynamics, our simulation shows the transition from collective oscillation to amplitude death as inter-bundle coupling str...
A Tannakian approach to dimensional reduction of principal bundles
Álvarez-Cónsul, Luis; García-Prada, Oscar
2016-01-01
Let $P$ be a parabolic subgroup of a connected simply connected complex semisimple Lie group $G$. Given a compact K\\"ahler manifold $X$, the dimensional reduction of $G$-equivariant holomorphic vector bundles over $X\\times G/P$ was carried out by the first and third authors. This raises the question of dimensional reduction of holomorphic principal bundles over $X\\times G/P$. The method used for equivariant vector bundles does not generalize to principal bundles. In this paper, we adapt to equivariant principal bundles the Tannakian approach of Nori, to describe the dimensional reduction of $G$-equivariant principal bundles over $X\\times G/P$, and to establish a Hitchin--Kobayashi type correspondence. In order to be able to apply the Tannakian theory, we need to assume that $X$ is a complex projective manifold.
Hydrodynamic behavior of a bare rod bundle
International Nuclear Information System (INIS)
The temperature distribution within the rod bundle of a nuclear reactor is of major importance in nuclear reactor design. However temperature information presupposes knowledge of the hydrodynamic behavior of the coolant which is the most difficult part of the problem due to complexity of the turbulence phenomena. In the present work a 2-equation turbulence model--a strong candidate for analyzing actual three dimensional turbulent flows--has been used to predict fully developed flow of infinite bare rod bundle of various aspect ratios (P/D). The model has been modified to take into account anisotropic effects of eddy viscosity. Secondary flow calculations have been also performed although the model seems to be too rough to predict the secondary flow correctly. Heat transfer calculations have been performed to confirm the importance of anisotropic viscosity in temperature predictions. All numerical calculations for flow and heat have been performed by two computer codes based on the TEACH code. Experimental measurements of the distribution of axial velocity, turbulent axial velocity, turbulent kinetic energy and radial Reynolds stresses were performed in the developing and fully developed regions. A 2-channel Laser Doppler Anemometer working on the Reference mode with forward scattering was used to perform the measurements in a simulated interior subchannel of a triangular rod array with P/D = 1.124. Comparisons between the analytical results and the results of this experiment as well as other experimental data in rod bundle array available in literature are presented. The predictions are in good agreement with the results for the high Reynolds numbers
Historical dynamics in ecosystem service bundles.
Renard, Delphine; Rhemtulla, Jeanine M; Bennett, Elena M
2015-10-27
Managing multiple ecosystem services (ES), including addressing trade-offs between services and preventing ecological surprises, is among the most pressing areas for sustainability research. These challenges require ES research to go beyond the currently common approach of snapshot studies limited to one or two services at a single point in time. We used a spatiotemporal approach to examine changes in nine ES and their relationships from 1971 to 2006 across 131 municipalities in a mixed-use landscape in Quebec, Canada. We show how an approach that incorporates time and space can improve our understanding of ES dynamics. We found an increase in the provision of most services through time; however, provision of ES was not uniformly enhanced at all locations. Instead, each municipality specialized in providing a bundle (set of positively correlated ES) dominated by just a few services. The trajectory of bundle formation was related to changes in agricultural policy and global trends; local biophysical and socioeconomic characteristics explained the bundles' increasing spatial clustering. Relationships between services varied through time, with some provisioning and cultural services shifting from a trade-off or no relationship in 1971 to an apparent synergistic relationship by 2006. By implementing a spatiotemporal perspective on multiple services, we provide clear evidence of the dynamic nature of ES interactions and contribute to identifying processes and drivers behind these changing relationships. Our study raises questions about using snapshots of ES provision at a single point in time to build our understanding of ES relationships in complex and dynamic social-ecological systems. PMID:26460005
Numerical simulations of square arrayed rod bundles
International Nuclear Information System (INIS)
Highlights: ► CFD simulations with square arrayed rod bundles. ► Mesh dependency and turbulence model study by comparison with experiments. ► Gibson and Launder Reynolds stress model shows good agreement with experiments. ► Effect of pitch to diameter ratio and Reynolds number is correctly captured. - Abstract: Computational fluid dynamics (CFD) simulations were performed with square arrayed rod bundles featuring pitch to diameter (P/D) ratio of 1.194 and 1.326 in order to find an optimal mesh and turbulence model for simulations with more complex geometries in the future. With the tighter lattice a mesh sensitivity and turbulence model study were accomplished and the post processed turbulence quantities, velocity field and wall shear stress were compared with experimental data ( Developed single phase turbulent flow through a square-pitch rod cluster. Nuclear Engineering and Design 60, 365–379.). The comparisons show that Reynolds-Averaged Navier–Stokes method with the Reynolds stress model of Gibson and Launder in conjunction with an appropriate mesh can provide reasonable agreement with the experiment for this lattice. For pure bundle simulations the body fitted structured meshes are suggested, since slightly better agreement can be captured considering all quantities with the same number of cells. Based on the drawn conclusions the procession was repeated for P/D = 1.326, where, due to lack of experiment, just the correct tendencies of the turbulence quantities and velocity field were established. The results show Reynolds number independency correctly and the increase of P/D issues in more similar flow to axisymmetric pipe flow.
Systematic Bundle Adjustment of HRSC Image Data
Bostelmann, J.; Schmidt, R.; Heipke, C.
2012-07-01
The European Mars Express mission was launched in June 2003 and sent into orbit around Mars. On board the orbiter is the German High Resolution Stereo Camera (HRSC). This multi-line sensor images the Martian surface with a resolution of up to 12m per pixel in three dimensions and provides RGB and infra-red color information. The usage of the stereoscopic image information for the improvement of the observed position and attitude information via bundle adjustment is important to derive high quality 3D surface models, color orthoimages and other data products. In many cases overlapping image strips of different orbits can be used to form photogrammetric blocks, thus allowing the simultaneous adjustment of the exterior orientation data. This reduces not only local, but also regional inconsistencies in the data. With the growing number of HRSC image strips in this ongoing mission, the size and complexity of potential blocks is increasing. Therefore, a workflow has been built up for the systematic improvement of the exterior orientation using single orbit strips and regional blocks. For a successful bundle adjustment of blocks using multiple image strips a sufficient number of tie points in the overlapping area is needed. The number of tie points depends mainly on the geometric and radiometric quality of the images. This is considered by detailed analysis of the tie point accuracy and distribution. The combination of methods for image pre-processing, tie point matching, bundle adjustment and evaluation of the results in an automated workflow allows for all HRSC images a global assessment of the quality and a systematic selection of data for larger blocks.
Tiling spaces are Cantor set fiber bundles
Sadun, Lorenzo; Williams, R F
2001-01-01
We prove that fairly general spaces of tilings of R^d are fiber bundles over the torus T^d, with totally disconnected fiber. This was conjectured (in a weaker form) in [W3], and proved in certain cases. In fact, we show that each such space is homeomorphic to the d-fold suspension of a Z^d subshift (or equivalently, a tiling space whose tiles are marked unit d-cubes). The only restrictions on our tiling spaces are that 1) the tiles are assumed to be polygons (polyhedra if d>2) that meet full-...
Higher order mechanics on graded bundles
International Nuclear Information System (INIS)
In this paper we develop a geometric approach to higher order mechanics on graded bundles in both, the Lagrangian and Hamiltonian formalism, via the recently discovered weighted algebroids. We present the corresponding Tulczyjew triple for this higher order situation and derive in this framework the phase equations from an arbitrary (also singular) Lagrangian or Hamiltonian, as well as the Euler–Lagrange equations. As important examples, we geometrically derive the classical higher order Euler–Lagrange equations and analogous reduced equations for invariant higher order Lagrangians on Lie groupoids. (paper)
Assembly mechanism for nuclear fuel bundles
International Nuclear Information System (INIS)
The invention relates to a nuclear power reactor fuel bundle of the type wherein several rods are mounted in parallel array between two tie plates which secure the fuel rods in place and are maintained in assembled position by means of a number of tie rods secured to both of the end plates. Improved apparatus is provided for attaching the tie rods to the upper tie plate by the use of locking lugs fixed to rotatable sleeves which engage the upper tie plate. (auth)
Compression of a bundle of light rays.
Marcuse, D
1971-03-01
The performance of ray compression devices is discussed on the basis of a phase space treatment using Liouville's theorem. It is concluded that the area in phase space of the input bundle of rays is determined solely by the required compression ratio and possible limitations on the maximum ray angle at the output of the device. The efficiency of tapers and lenses as ray compressors is approximately equal. For linear tapers and lenses the input angle of the useful rays must not exceed the compression ratio. The performance of linear tapers and lenses is compared to a particular ray compressor using a graded refractive index distribution. PMID:20094478
Differential geometry of complex vector bundles
Kobayashi, Shoshichi
2014-01-01
Holomorphic vector bundles have become objects of interest not only to algebraic and differential geometers and complex analysts but also to low dimensional topologists and mathematical physicists working on gauge theory. This book, which grew out of the author's lectures and seminars in Berkeley and Japan, is written for researchers and graduate students in these various fields of mathematics. Originally published in 1987. The Princeton Legacy Library uses the latest print-on-demand technology to again make available previously out-of-print books from the distinguished backlist of Princeto
A Unified Framework for Quasi-Linear Bundle Adjustment
Bartoli, Adrien
2002-01-01
Obtaining 3D models from long image sequences is a major issue in computer vision. One of the main tools used to obtain accurate structure and motion estimates is bundle adjustment. Bundle adjustment is usually performed using nonlinear Newton-type optimizers such as Levenberg-Marquardt which might be quite slow when handling a large number of points or views. We investigate an algorithm for bundle adjustment based on quasi-linear optimization. The method is straightforward to implement and r...
Non-commutative P-1-bundles over commutative schemes
Van den Bergh, Michel
2012-01-01
In this paper we develop the theory of non-commutative P-1-bundles over commutative (smooth) schemes. Such non-commutative P-1-bundles occur in the theory of D-modules but our definition is more general. We can show that every non-commutative deformation of a Hirzebruch surface is given by a non-commutative P-1-bundle over P-1 in our sense.
Contacting single bundles of carbon nanotubes with alternating electric fields
Krupke, R.; Hennrich, F.; Weber, H. B.; Beckmann, D.; Hampe, O.; Malik, S.; Kappes, M. M.; Löhneysen, H. v.
2002-01-01
Single bundles of carbon nanotubes have been selectively deposited from suspensions onto sub-micron electrodes with alternating electric fields. We explore the resulting contacts using several solvents and delineate the differences between Au and Ag as electrode materials. Alignment of the bundles between electrodes occurs at frequencies above 1 kHz. Control over the number of trapped bundles is achieved by choosing an electrode material which interacts strongly with the chemical functional g...
Dark-field illuminated reflectance fiber bundle endoscopic microscope
Liu, Xuan; Huang, Yong; Kang, Jin U.
2011-01-01
We propose a reflectance fiber bundle microscope using a dark-field illumination configuration for applications in endoscopic medical imaging and diagnostics. Our experiment results show that dark-field illumination can effectively suppress strong specular reflection from the proximal end of the fiber bundle. We realized a lateral resolution of 4.4 μm using the dark-field illuminated fiber bundle configuration. To demonstrate the feasibility of using the system to study cell morphology, we ob...
A viscous two-phase model for contractile actomyosin bundles.
Oelz, Dietmar
2014-06-01
A mathematical model in one dimension for a non-sarcomeric actomyosin bundle featuring anti-parallel flows of anti-parallel F-actin is introduced. The model is able to relate these flows to the effect of cross-linking and bundling proteins, to the forces due to myosin-II filaments and to external forces at the extreme tips of the bundle. The modeling is based on a coarse graining approach starting with a microscopic model which includes the description of chemical bonds as elastic springs and the force contribution of myosin filaments. In a second step we consider the asymptotic regime where the filament lengths are small compared to the overall bundle length and restrict to the lowest order contributions. There it becomes apparent that myosin filaments generate forces which are partly compensated by drag forces due to cross-linking proteins. The remaining local contractile forces are then propagated to the tips of the bundle by the viscosity effect of bundling proteins in the filament gel. The model is able to explain how a disordered bundle of comparatively short actin filaments interspersed with myosin filaments can effectively contract the two tips of the actomyosin bundle. It gives a quantitative description of these forces and of the anti-parallel flows of the two phases of anti-parallel F-actin. An asymptotic version of the model with infinite viscosity can be solved explicitly and yields an upper bound to the contractile force of the bundle. PMID:23670678
Robust Mapping of Incoherent Fiber-Optic Bundles
Roberts, Harry E.; Deason, Brent E.; DePlachett, Charles P.; Pilgrim, Robert A.; Sanford, Harold S.
2007-01-01
A method and apparatus for mapping between the positions of fibers at opposite ends of incoherent fiber-optic bundles have been invented to enable the use of such bundles to transmit images in visible or infrared light. The method is robust in the sense that it provides useful mapping even for a bundle that contains thousands of narrow, irregularly packed fibers, some of which may be defective. In a coherent fiber-optic bundle, the input and output ends of each fiber lie at identical positions in the input and output planes; therefore, the bundle can be used to transmit images without further modification. Unfortunately, the fabrication of coherent fiber-optic bundles is too labor-intensive and expensive for many applications. An incoherent fiber-optic bundle can be fabricated more easily and at lower cost, but it produces a scrambled image because the position of the end of each fiber in the input plane is generally different from the end of the same fiber in the output plane. However, the image transmitted by an incoherent fiber-optic bundle can be unscrambled (or, from a different perspective, decoded) by digital processing of the output image if the mapping between the input and output fiber-end positions is known. Thus, the present invention enables the use of relatively inexpensive fiber-optic bundles to transmit images.
Enthalpy and void distributions in subchannels of PHWR fuel bundles
Energy Technology Data Exchange (ETDEWEB)
Park, J. W.; Choi, H.; Rhee, B. W. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)
1998-12-31
Two different types of the CANDU fuel bundles have been modeled for the ASSERT-IV code subchannel analysis. From calculated values of mixture enthalpy and void fraction distribution in the fuel bundles, it is found that net buoyancy effect is pronounced in the central region of the DUPIC fuel bundle when compared with the standard CANDU fuel bundle. It is also found that the central region of the DUPIC fuel bundle can be cooled more efficiently than that of the standard fuel bundle. From the calculated mixture enthalpy distribution at the exit of the fuel channel, it is found that the mixture enthalpy and void fraction can be highest in the peripheral region of the DUPIC fuel bundle. On the other hand, the enthalpy and the void fraction were found to be highest in the central region of the standard CANDU fuel bundle at the exit of the fuel channel. This study shows that the subchannel analysis is very useful in assessing thermal behavior of the fuel bundle that could be used in CANDU reactors. 10 refs., 4 figs., 2 tabs. (Author)
Steady-flow characteristics of bundle fluid in drawing
Energy Technology Data Exchange (ETDEWEB)
Huh, You; Kim, Jong Seong [Kyunghee University, Suwon (Korea, Republic of)
2006-07-15
Drawing is a mechanical operation attenuating material thickness to an appropriate level for the next processing or end usage. When the input material has a form of bundle or bundles made of very thin and long shaped wires or fibers, this attenuation operation is called 'bundle drawing' or 'drafting'. Bundle drawing is being used widely in manufacturing micro sized wires or staple yarns. However, the bundle processed by this operation has more or less defects in the evenness of linear density. Such irregularities cause many problems not only for the product quality but also for the efficiency of the next successive processes. In this research a mathematical model for the dynamic behavior of the bundle fluid is to be set up on the basis of general physical laws containing physical variables, i.e. linear density and velocity as the dynamic state variables of the bundle fluid. The governing equations resulting from the modeling show that they appear in a slightly different form from what they do in a continuum fluid. Then, the governing equations system is simplified in a steady state and the bundle dynamics is simulated, showing that the shape of the velocity profiles depends on two model parameters. Experiments confirm that the model parameters are to be well adjusted to show a coincidence with the theoretical analysis. The higher the drawing ratio and drawing speed are, the more sensitive becomes the bundle flow to exogenous disturbances.
Bundle formation in parallel aligned polymers with competing interactions
Dutta, Sandipan; Benetatos, P.; Jho, Y. S.
2016-04-01
Aggregation of like-charged polymers is widely observed in biological- and soft-matter systems. In many systems, bundles are formed when a short-range attraction of diverse physical origin like charge bridging, hydrogen bonding or hydrophobic interaction, overcomes the longer-range charge repulsion. In this letter, we present a general mechanism of bundle formation in these systems as the breaking of the translational invariance in parallel aligned polymers with competing interactions of this type. We derive a criterion for finite-sized bundle formation as well as for macroscopic phase separation (formation of infinite bundles).
Annular burnout data from rod-bundle experiments
International Nuclear Information System (INIS)
Burnout data for annular flow in a rod bundle are presented for both transient and steady-state conditions. Tests were performed at the Oak Ridge National Laboratory in the Thermal Hydraulic Test Facility (THTF), a pressurized-water loop containing an electrically heated 64-rod bundle. The bundle configuration is typical of later generation pressurized-water reactors with 17 x 17 fuel arrays. Both axial and radial power profiles are flat. All experiments were carried out in upflow with subcooled inlet conditions, insuring accurate flow measurement. Conditions within the bundle were typical of those which could be encountered during a nuclear reactor loss-of-coolant accident
Confinement-dependent friction in peptide bundles.
Erbaş, Aykut; Netz, Roland R
2013-03-19
Friction within globular proteins or between adhering macromolecules crucially determines the kinetics of protein folding, the formation, and the relaxation of self-assembled molecular systems. One fundamental question is how these friction effects depend on the local environment and in particular on the presence of water. In this model study, we use fully atomistic MD simulations with explicit water to obtain friction forces as a single polyglycine peptide chain is pulled out of a bundle of k adhering parallel polyglycine peptide chains. The whole system is periodically replicated along the peptide axes, so a stationary state at prescribed mean sliding velocity V is achieved. The aggregation number is varied between k = 2 (two peptide chains adhering to each other with plenty of water present at the adhesion sites) and k = 7 (one peptide chain pulled out from a close-packed cylindrical array of six neighboring peptide chains with no water inside the bundle). The friction coefficient per hydrogen bond, extrapolated to the viscous limit of vanishing pulling velocity V → 0, exhibits an increase by five orders of magnitude when going from k = 2 to k = 7. This dramatic confinement-induced friction enhancement we argue to be due to a combination of water depletion and increased hydrogen-bond cooperativity. PMID:23528088
Directory of Open Access Journals (Sweden)
Masataka Deie
2015-01-01
Full Text Available Background. Posterior cruciate ligament (PCL injuries are not rare in acute knee injuries, and several recent anatomical studies of the PCL and reconstructive surgical techniques have generated improved patient results. Now, we have evaluated PCL reconstructions performed by either the single-bundle or double-bundle technique in a patient group followed up retrospectively for more than 10 years. Methods. PCL reconstructions were conducted using the single-bundle (27 cases or double-bundle (13 cases method from 1999 to 2002. The mean age at surgery was 34 years in the single-bundle group and 32 years in the double-bundle group. The mean follow-up period was 12.5 years. Patients were evaluated by Lysholm scoring, the gravity sag view, and knee arthrometry. Results. The Lysholm score after surgery was 89.1±5.6 points for the single-bundle group and 91.9±4.5 points for the double-bundle group. There was no significant difference between the methods in the side-to-side differences by gravity sag view or knee arthrometer evaluation, although several cases in both groups showed a side-to-side difference exceeding 5 mm by the latter evaluation method. Conclusions. We found no significant difference between single- and double-bundle PCL reconstructions during more than 10 years of follow-up.
Subanalytic Bundles and Tubular Neighbourhoods of Zero-Loci
Indian Academy of Sciences (India)
Vishwambhar Pati
2003-08-01
We introduce the natural and fairly general notion of a subanalytic bundle (with a finite dimensional vector space of sections) on a subanalytic subset of a real analytic manifold , and prove that when is compact, there is a Baire subset of sections in whose zero-loci in have tubular neighbourhoods, homeomorphic to the restriction of the given bundle to these zero-loci.
Quantum principal bundles as Hopf-Galois extensions
Durdevic, M
1995-01-01
It is shown that every quantum principal bundle with a compact structure group is a Hopf-Galois extension. This property naturally extends to the level of general differential structures, so that every differential calculus over a quantum principal bundle with a compact structure group is a graded-differential variant of the Hopf-Galois extension.
Lexical Bundles in L1 and L2 Academic Writing
Chen, Yu-Hua; Baker, Paul
2010-01-01
This paper adopts an automated frequency-driven approach to identify frequently-used word combinations (i.e., "lexical bundles") in academic writing. Lexical bundles retrieved from one corpus of published academic texts and two corpora of student academic writing (one L1, the other L2), were investigated both quantitatively and qualitatively.…
On the Classification of Complex Vector Bundles of Stable Rank
Indian Academy of Sciences (India)
Constantin Bǎnicǎ; Mihai Putinar
2006-08-01
One describes, using a detailed analysis of Atiyah–Hirzebruch spectral sequence, the tuples of cohomology classes on a compact, complex manifold, corresponding to the Chern classes of a complex vector bundle of stable rank. This classification becomes more effective on generalized flag manifolds, where the Lie algebra formalism and concrete integrability conditions describe in constructive terms the Chern classes of a vector bundle.
On the general elephant conjecture for Mori conic bundles
Prokhorov, Yu G
1996-01-01
Let $f:X\\to S$ be an extremal contraction from a threefolds with terminal singularities onto a surface (so called Mori conic bundle). We study some particular cases of such contractions: quotients of usual conic bundles and index two contractions. Assuming Reid's general elephants conjecture we also obtain a rough classification. We present many examples.
CANDU bundle junction. Misalignment probability and pressure-drop correlation
International Nuclear Information System (INIS)
The pressure drop over the bundle junction is an important component of the pressure drop in a CANDU (Canada Deuterium Uranium) fuel channel. This component can represent from ∼ 15% for aligned bundles to ∼ 26% for rotationally misaligned bundles, and is dependent on the degree of misalignment. The geometry of the junction increases the mixing between subchannels, and hence improves the thermal performance of the bundle immediately downstream. It is therefore important to model the junction's performance adequately. This paper summarizes a study sponsored by COG (CANDU Owners Group) and an NSERC (National Science and Engineering Research Council) Industrial Research Grant, undertaken, at CRL (Chalk River Laboratories) to identify and develop a bundle-junction model for potential implementation in the ASSERT (Advanced Solution of Subchannel Equations in Reactor Thermalhydraulics) subchannel code. The work reported in this paper consists of two components of this project: an examination of the statistics of bundle misalignment, demonstrating that there are no preferred positions for the bundles and therefore all misalignment angles are equally possible; and, an empirical model for the single-phase pressure drop across the junction as a function of the misalignment angle. The second section of this paper includes a brief literature review covering the experimental, analytical and numerical studies concerning the single-phase pressure drop across bundle junctions. 32 refs., 9 figs
Trace extensions, determinant bundles, and gauge group cocycles
Arnlind, J; Arnlind, Joakim; Mickelsson, Jouko
2002-01-01
We study the geometry of determinant line bundles associated to Dirac operators on compact odd dimensional manifolds. Physically, these arise as (local) vacuum line bundles in quantum gauge theory. We give a simplified derivation of the commutator anomaly formula using a construction based on noncyclic trace extensions and associated multiplicative renormalized determinants.
Bundle power history envelope using a theoretical method
International Nuclear Information System (INIS)
This paper gives a simple theoretical method for calculating a bundle power history envelope which envelopes all possible individual bundle power versus burnup histories. The lattice parameters at different burnups were generated by computer code CLUB. (author). 2 refs., 1 tab., 2 figs
Bundled slaty cleavage in laminated argillite, north-central minnesota
Southwick, D.L.
1987-01-01
Exceptional bundled slaty cleavage (defined herein) has been found in drill cores of laminated, folded, weakly metamorphosed argillite at several localities in the early Proterozoic Animikie basin of north-central Minnesota. The cleavage domains are more closely spaced within the cleavage bundles than outside them, the mean tectosilicate grain size of siltstone layers, measured normal to cleavage, is less in the cleavage bundles than outside them, and the cleavage bundles are enriched in opaque phases and phyllosilicates relative to extra-bundle segments. These facts suggest that pressure solution was a major factor in bundle development. If it is assumed that opaque phases have been conserved during pressure solution, the modal differences in composition between intra-bundle and extra-bundle segments of beds provide a means for estimating bulk material shortening normal to cleavage. Argillite samples from the central part of the Animikie basin have been shortened a minimum of about 22%, as estimated by this method. These estimates are similar to the shortening values derived from other strain markers in other rock types interbedded with the argillite, and are also consistent with the regional pattern of deformation. ?? 1987.
The behaviour of Phenix fuel pin bundle under irradiation
International Nuclear Information System (INIS)
An entire Phenix sub-assembly has been mounted and sectioned after irradiation. The examination of cross-sections revealed the effects of mechanical interaction in the bundle (ovalisations and contacts between clads). According to analysis of the sodium channels, cooling of the pin bundle remained uniform. (author)
Restriction Theorem for Principal bundles in Arbitrary Characteristic
DEFF Research Database (Denmark)
Gurjar, Sudarshan
2015-01-01
The aim of this paper is to prove two basic restriction theorem for principal bundles on smooth projective varieties in arbitrary characteristic generalizing the analogues theorems of Mehta-Ramanathan for vector bundles. More precisely, let G be a reductive algebraic group over an algebraically c...
Phase Space Reduction of Star Products on Cotangent Bundles.
N. Kowalzig; N. Neumaier; M. Pflaum
2005-01-01
In this paper we construct star products on Marsden-Weinstein reduced spaces in case both the original phase space and the reduced phase space are (symplectomorphic to) cotangent bundles. Under the assumption that the original cotangent bundle $T^*Q$ carries a symplectic structure of form $\\omega_{B
Artificial ciliary bundles with nano fiber tip links
Asadnia, Mohsen; Miao, Jianmin; Triantafyllou, Michael
2015-01-01
Mechanosensory ciliary bundles in fishes are the inspiration for carefully engineered artificial flow sensors. We report the development of a new class of ultrasensitive MEMS flow sensors that mimic the intricate morphology of the ciliary bundles, including the stereocilia, tip links, and the cupula, and thereby achieve threshold detection limits that match the biological example. An artificial ciliary bundle is achieved by fabricating closely-spaced arrays of polymer micro-pillars with gradiating heights. Tip links that form the fundamental sensing elements are realized through electrospinning aligned PVDF piezoelectric nano-fibers that link the distal tips of the polymer cilia. An optimized synthesis of hyaluronic acid-methacrylic anhydride hydrogel that results in properties close to the biological cupula, together with drop-casting method are used to form the artificial cupula that encapsulates the ciliary bundle. In testing, fluid drag force causes the ciliary bundle to slide, stretching the flexible nan...
Introduction to the theory of fiber bundles and connections I
International Nuclear Information System (INIS)
In lectures 1 and 2 we discuss basic concepts of topology and differential geometry: definition of a topological space and of Hausdorff, compact, connected and paracompact spaces; topological groups and actions of groups on spaces; differentiable manifolds, tangent vectors and 1 forms; partitions of unity and Lie groups. In lecture 3 we present the concept of a fiber bundle and discuss vector bundles and principal bundles. The concept of a connection on a smooth vector bundle is defined in lecture 4, together with the associated concepts of curvature and parallel transport; as an illustration we present the Levi-Civita connection on a Riemannian manifold. Finally, in lecture 5 we define connections on principal bundles and present examples with the Lie groups U(1) and SU(2). For reasons of space the present article only includes lectures 1, 2 and 3. Lectures 4 and 5 will be published in a forthcoming paper. (Author)
HORIZONTAL LAPLACE OPERATOR IN REAL FINSLER VECTOR BUNDLES
Institute of Scientific and Technical Information of China (English)
无
2008-01-01
A vector bundle F over the tangent bundle TM of a manifold M is said to be a Finsler vector bundle if it is isomorphic to the pull-back π*E of a vector bundle E over M([1]). In this article the authors study the h-Laplace operator in Finsler vector bundles.An h-Laplace operator is defined, first for functions and then for horizontal Finsler forms on E. Using the h-Laplace operator, the authors define the h-harmonic function and h-harmonic horizontal Finsler vector fields, and furthermore prove some integral formulas for the h-Laplace operator, horizontal Finsler vector fields, and scalar fields on E.
Development of nuclear fuel. Development of CANDU advanced fuel bundle
International Nuclear Information System (INIS)
In order to develop CANDU advanced fuel, the agreement of the joint research between KAERI and AECL was made on February 19, 1991. AECL conceptual design of CANFLEX bundle for Bruce reactors was analyzed and then the reference design and design drawing of the advanced fuel bundle with natural uranium fuel for CANDU-6 reactor were completed. The CANFLEX fuel cladding was preliminarily investigated. The fabricability of the advanced fuel bundle was investigated. The design and purchase of the machinery tools for the bundle fabrication for hydraulic scoping tests were performed. As a result of CANFLEX tube examination, the tubes were found to be meet the criteria proposed in the technical specification. The dummy bundles for hydraulic scoping tests have been fabricated by using the process and tools, where the process parameters and tools have been newly established. (Author)
Composite bundles in Clifford algebras. Gravitation theory. Part I
Sardanashvily, G
2016-01-01
Based on a fact that complex Clifford algebras of even dimension are isomorphic to the matrix ones, we consider bundles in Clifford algebras whose structure group is a general linear group acting on a Clifford algebra by left multiplications, but not a group of its automorphisms. It is essential that such a Clifford algebra bundle contains spinor subbundles, and that it can be associated to a tangent bundle over a smooth manifold. This is just the case of gravitation theory. However, different these bundles need not be isomorphic. To characterize all of them, we follow the technique of composite bundles. In gravitation theory, this technique enables us to describe different types of spinor fields in the presence of general linear connections and under general covariant transformations.
The 2-Hilbert Space of a Prequantum Bundle Gerbe
Bunk, Severin; Szabo, Richard J
2016-01-01
We construct a prequantum 2-Hilbert space for any line bundle gerbe whose Dixmier-Douady class is torsion. Analogously to usual prequantisation, this 2-Hilbert space has the category of sections of the line bundle gerbe as its underlying 2-vector space. These sections are obtained as certain morphism categories in Waldorf's version of the 2-category of line bundle gerbes. We show that these morphism categories carry a monoidal structure under which they are semisimple and abelian. We introduce a dual functor on the sections, which yields a closed structure on the morphisms between bundle gerbes and turns the category of sections into a 2-Hilbert space. We discuss how these 2-Hilbert spaces fit various expectations from higher prequantisation. We then extend the transgression functor to the full 2-category of bundle gerbes and demonstrate its compatibility with the additional structures introduced. We discuss various aspects of Kostant-Souriau prequantisation in this setting, including its dimensional reductio...
Bundles over Quantum RealWeighted Projective Spaces
Directory of Open Access Journals (Sweden)
Tomasz Brzeziński
2012-09-01
Full Text Available The algebraic approach to bundles in non-commutative geometry and the definition of quantum real weighted projective spaces are reviewed. Principal U(1-bundles over quantum real weighted projective spaces are constructed. As the spaces in question fall into two separate classes, the negative or odd class that generalises quantum real projective planes and the positive or even class that generalises the quantum disc, so do the constructed principal bundles. In the negative case the principal bundle is proven to be non-trivial and associated projective modules are described. In the positive case the principal bundles turn out to be trivial, and so all the associated modules are free. It is also shown that the circle (coactions on the quantum Seifert manifold that define quantum real weighted projective spaces are almost free.
Geometries and applications of active fiber bundles
Giglmayr, Josef
2001-10-01
Active fiber bundles (FBs) are aimed to model photonic switching and processing in 3-D without the restrictions of the photonic technology. The 2-D photonic architectures are assumed to be implemented by networks of directional couplers (DCs) and Mach-Zehnder interferometers (MZIs), respectively. For the implementation several crucial problems are expected: (1) proper operation of the spatial couplers/switches (nonblocking interconnections) and (2) coupling in the interstage interconnection section mainly caused by parallel and crossing fibers/waveguides (WGs). For the design of proper operating switches (refinement of couplers) the application of decoupling concepts of modern control theory is proposed. The final goal is to translate the refined couplers into integrated photonic architectures rather than into additional lightwave circuits (LWCs) which simply would increase the coupling. The decoupling concepts are reviewed. The paper is an attempt to prepare for applying well-known system engineering concepts to the upcoming technology of photonics.
Extendability of parallel sections in vector bundles
Kirschner, Tim
2016-01-01
I address the following question: Given a differentiable manifold M, what are the open subsets U of M such that, for all vector bundles E over M and all linear connections ∇ on E, any ∇-parallel section in E defined on U extends to a ∇-parallel section in E defined on M? For simply connected manifolds M (among others) I describe the entirety of all such sets U which are, in addition, the complement of a C1 submanifold, boundary allowed, of M. This delivers a partial positive answer to a problem posed by Antonio J. Di Scala and Gianni Manno (2014). Furthermore, in case M is an open submanifold of Rn, n ≥ 2, I prove that the complement of U in M, not required to be a submanifold now, can have arbitrarily large n-dimensional Lebesgue measure.
TRIGA modified bundle thermal hydraulic analysis
Energy Technology Data Exchange (ETDEWEB)
Negut, G.; Mladin, M.; Preda, M. [Inst. for Nuclear Research, Pitesti (Romania)
2001-07-01
TRIGA 14 MW steady state reactor (SSR) has more than 20 years of operation experience. It was used as a material test reactor to accomplish full range of experiments of CANDU type fuel, tests on structure material as Zircaloy and stainless steel. We did, also, isotope production for industrial and medical use, neutronography, gamma prompt, neutron diffractometry and activation analysis. In order to optimize the core for a more homogenous burnup we did some experiments on a modified fuel bundle. The paper is dedicated to the computations done in order to validate the optimized core configuration. The analysis has shown no significant impact on the central fuel temperatures, to affect the core safety. (orig.)
TRIGA modified bundle thermal hydraulic analysis
International Nuclear Information System (INIS)
TRIGA 14 MW steady state reactor (SSR) has more than 20 years of operation experience. It was used as a material test reactor to accomplish full range of experiments of CANDU type fuel, tests on structure material as Zircaloy and stainless steel. We did, also, isotope production for industrial and medical use, neutronography, gamma prompt, neutron diffractometry and activation analysis. In order to optimize the core for a more homogenous burnup we did some experiments on a modified fuel bundle. The paper is dedicated to the computations done in order to validate the optimized core configuration. The analysis has shown no significant impact on the central fuel temperatures, to affect the core safety. (orig.)
Effect of Reynolds number and bundle geometry on the turbulent flow in tight lattice bundle
International Nuclear Information System (INIS)
The flow structure in tight lattice is still of great interest to nuclear industry. The accurate prediction of flow parameter in subchannels of tight lattice is likable. Unsteady Reynolds Averaged Navier Stokes (URANS) is a promising approach to achieve this goal. The implementation of URANS (Unsteady Reynolds Averaged Navier Stokes) approach will be validated by comparing computational results with the experimental data of Krauss (1998). In this paper, the turbulent flow with different Reynolds number (5000~215000) and different P/D(1.005~1.2) are simulated with CFD code CFX12.The effects of the Reynolds number and the bundle geometry(P/D) on wall shear stress, turbulent kinetic energy, turbulent mixing and large scale coherent structure in tight lattice are analyzed in details. It is hoped that the present work will contribute to the understanding of these important flow phenomena and facilitate the prediction and design of rod bundles. (author)
Fiber bundle model under fluid pressure
Amitrano, David; Girard, Lucas
2016-03-01
Internal fluid pressure often plays an important role in the rupture of brittle materials. This is a major concern for many engineering applications and for natural hazards. More specifically, the mechanisms through which fluid pressure, applied at a microscale, can enhance the failure at a macroscale and accelerate damage dynamics leading to failure remains unclear. Here we revisit the fiber bundle model by accounting for the effect of fluid under pressure that contributes to the global load supported by the fiber bundle. Fluid pressure is applied on the broken fibers, following Biot's theory. The statistical properties of damage avalanches and their evolution toward macrofailure are analyzed for a wide range of fluid pressures. The macroscopic strength of the new model appears to be strongly controlled by the action of the fluid, particularly when the fluid pressure becomes comparable with the fiber strength. The behavior remains consistent with continuous transition, i.e., second order, including for large pressure. The main change concerns the damage acceleration toward the failure that is well modeled by the concept of sweeping of an instability. When pressure is increased, the exponent β characterizing the power-law distribution avalanche sizes significantly decreases and the exponent γ characterizing the cutoff divergence when failure is approached significantly increases. This proves that fluid pressure plays a key role in failure process acting as destabilization factor. This indicates that macrofailure occurs more readily under fluid pressure, with a behavior that becomes progressively unstable as fluid pressure increases. This may have considerable consequences on our ability to forecast failure when fluid pressure is acting.
Fiber bundle model under fluid pressure.
Amitrano, David; Girard, Lucas
2016-03-01
Internal fluid pressure often plays an important role in the rupture of brittle materials. This is a major concern for many engineering applications and for natural hazards. More specifically, the mechanisms through which fluid pressure, applied at a microscale, can enhance the failure at a macroscale and accelerate damage dynamics leading to failure remains unclear. Here we revisit the fiber bundle model by accounting for the effect of fluid under pressure that contributes to the global load supported by the fiber bundle. Fluid pressure is applied on the broken fibers, following Biot's theory. The statistical properties of damage avalanches and their evolution toward macrofailure are analyzed for a wide range of fluid pressures. The macroscopic strength of the new model appears to be strongly controlled by the action of the fluid, particularly when the fluid pressure becomes comparable with the fiber strength. The behavior remains consistent with continuous transition, i.e., second order, including for large pressure. The main change concerns the damage acceleration toward the failure that is well modeled by the concept of sweeping of an instability. When pressure is increased, the exponent β characterizing the power-law distribution avalanche sizes significantly decreases and the exponent γ characterizing the cutoff divergence when failure is approached significantly increases. This proves that fluid pressure plays a key role in failure process acting as destabilization factor. This indicates that macrofailure occurs more readily under fluid pressure, with a behavior that becomes progressively unstable as fluid pressure increases. This may have considerable consequences on our ability to forecast failure when fluid pressure is acting. PMID:27078437
Anatomic double-bundle anterior crucial ligament reconstruction with G-ST
Kuroda, Ryosuke; Matsushita, Takehiko
2011-01-01
The anterior cruciate ligament (ACL) consists of two primal functional bundles, anteromedial bundle and posterolateral bundles. Those two bundles play different functional roles and contribute differently to knee stability throughout the range of motion. Recent advancement in studies of anatomy and biomechanics of ACL has led surgeons to perform double-bundle ACL reconstruction to obtain better stability and kinematics. Consequently, variable surgical techniques of double-bundle ACL reconstru...
An experimental assessment of cooling of a 54-rod bundle by in-bundle injection
International Nuclear Information System (INIS)
Highlights: ► Rewetting of a 54-rod bundle assembled with a central coolant tube is investigated. ► The coolant tube injects the coolant radially outwards at different axial levels. ► Above a minimum flow rate, coolant quenches all the rods throughout their length. ► Rapid cooling of rods occurs up to around 100 °C of the rod surface temperature. ► Counter current flow of steam–water gets generated which affects cooling adversely. - Abstract: The performance of an in-bundle coolant injection system for the quenching of dry heated rods has been experimentally investigated. The rod bundle contains 54 fuel rods of 11.2 mm diameter, 3700 mm long, arranged in three concentric rings with a central coolant supply tube. The coolant tube supplies the coolant in the form of jets through a series of circumferential holes at different axial levels inside the rod bundle. Visualization during cold state injection tests ensures that the liquid spray can reach different levels of all the rods above a certain flow rate of water through the coolant tube. Extensive cooling experiments were done to assess the suitability of the proposed scheme of in-bundle coolant injection. Time–temperature curves have been derived from rods at different locations, from different heights of the rods, over a range of coolant flow rate as well as for different rod temperatures. The effect of the presence of the spacers on local cooling has also been investigated. The cooling curves follow a general trend of a rapid temperature drop up to almost 100 °C of the rod surface temperature irrespective of the operating parameters and the location of the rod. Thereafter, the temperature falls slowly reaching the coolant temperature almost asymptotically. Moreover, the second phase of cooling is often marked by temperature fluctuations of random nature. It was also observed that a large volume of steam generates during cooling and comes out through the top of the test section expelling a
Two-categorical bundles and their classifying spaces
DEFF Research Database (Denmark)
Baas, Nils A.; Bökstedt, M.; Kro, T.A.
2012-01-01
For a 2-category 2C we associate a notion of a principal 2C-bundle. In case of the 2-category of 2-vector spaces in the sense of M.M. Kapranov and V.A. Voevodsky this gives the the 2-vector bundles of N.A. Baas, B.I. Dundas and J. Rognes. Our main result says that the geometric nerve of a good 2......-category is a classifying space for the associated principal 2-bundles. In the process of proving this we develop a lot of powerful machinery which may be useful in further studies of 2-categorical topology. As a corollary we get a new proof of the classification of principal bundles. A calculation based...... on the main theorem shows that the principal 2-bundles associated to the 2-category of 2-vector spaces in the sense of J.C. Baez and A.S. Crans split, up to concordance, as two copies of ordinary vector bundles. When 2C is a cobordism type 2-category we get a new notion of cobordism-bundles which turns out...
The Geometry of Tangent Bundles: Canonical Vector Fields
Directory of Open Access Journals (Sweden)
Tongzhu Li
2013-01-01
Full Text Available A canonical vector field on the tangent bundle is a vector field defined by an invariant coordinate construction. In this paper, a complete classification of canonical vector fields on tangent bundles, depending on vector fields defined on their bases, is obtained. It is shown that every canonical vector field is a linear combination with constant coefficients of three vector fields: the variational vector field (canonical lift, the Liouville vector field, and the vertical lift of a vector field on the base of the tangent bundle.
On the existence of n-dimensional indecomposable vector bundles
International Nuclear Information System (INIS)
Let X be an arbitrary smooth irreducible complex projective curve of genus g with g ≥ 4. In this paper we extend the existence theorem of special divisors to high dimensional indecomposable vector bundles. We give a necessary and sufficient condition on the existence of n-dimensional indecomposable vector bundles E with deg(E) = d, dimH0(X,E) ≥ h. We also determine under what condition the set of all such vector bundles will be finite and how many elements it contains. (author). 9 refs
Line bundles and the Thom construction in noncommutative geometry
Beggs, E. J.; Brzezinski, T.
2010-01-01
The idea of a line bundle in classical geometry is transferred to noncommutative geometry by the idea of a Morita context. From this we can construct Z and N graded algebras, the Z graded algebra being a Hopf-Galois extension. A non-degenerate Hermitian metric gives a star structure on this algebra, and an additional star operation on the line bundle gives a star operation on the N graded algebra. In this case, we can carry out the associated circle bundle and Thom constructions. Starting wit...
On separation axioms of uniform bundles and sheaves
Clara M. Neira U.; Januario Varela
2004-01-01
In the context of the theory of uniform bundles in the sense of J. Dauns and K. H. Hofmann, the topology of the fiber space of a uniform bundle depends on the assumption of upper semicontinuity of its defining set of pseudometrics when composed with local sections. In this paper we show that the additional hypothesis of lower semicontinuity of these functions secures that the fiber space of the uniform bundle is Hausdorff, regular or completely regular provided that the base space has the cor...
Assembly mechanism for nuclear fuel bundles
International Nuclear Information System (INIS)
A method of securing a fuel bundle to permit easy remote disassembly is described. Fuel rods are held loosely between end plates, each end of the rods fitting into holes in the end plates. At the upper end of each fuel rod there is a spring pressing against the end plate. Tie rods are used to hold the end plates together securely. The lower end of each tie rod is screwed into the lower end plate; the upper end of each tie rod is attached to the upper end plate by means of a locking assembly described in the patent. In order to remove the upper tie plate during the disassembly process, it is necessary only to depress the tie plate against the pressure of the springs surrounding the fuel rods and then to rotate each locking sleeve on the tie rods from its locked to its unlocked position. It is then possible to remove the tie plate without disassembling the locking assembly. (LL)
Analysis of CHF experiment data for finned fuel bundle
International Nuclear Information System (INIS)
The HANARO uses finned-element fuel bundles. For thermal-hydraulic safety analysis, used is the MATRA-h code which is a modified version of KAERI's MATRA-α. The subchannel analysis model was determined by using the in-core irradiation test results and hydraulic experiment results for fuel bundle. The validity of the analysis model was investigated by comparing the MATRA-h predictions with the experimental results from several bundle CHF tests. The comparison showed that the code predictions for the CHF power were very close to or less than the experimental results. Thus, it was confirmed that the subchannel analysis using MATRA-h is to be applicable to the prediction of CHF phenomenon in HANARO fuel bundle
Bundles of Norms About Teen Sex and Pregnancy.
Mollborn, Stefanie; Sennott, Christie
2015-09-01
Teen pregnancy is a cultural battleground in struggles over morality, education, and family. At its heart are norms about teen sex, contraception, pregnancy, and abortion. Analyzing 57 interviews with college students, we found that "bundles" of related norms shaped the messages teens hear. Teens did not think their communities encouraged teen sex or pregnancy, but normative messages differed greatly, with either moral or practical rationalizations. Teens readily identified multiple norms intended to regulate teen sex, contraception, abortion, childbearing, and the sanctioning of teen parents. Beyond influencing teens' behavior, norms shaped teenagers' public portrayals and post hoc justifications of their behavior. Although norm bundles are complex to measure, participants could summarize them succinctly. These bundles and their conflicting behavioral prescriptions create space for human agency in negotiating normative pressures. The norm bundles concept has implications for teen pregnancy prevention policies and can help revitalize social norms for understanding health behaviors. PMID:25387911
Zeta Functions for Elliptic Curves I. Counting Bundles
Weng, Lin
2012-01-01
To count bundles on curves, we study zetas of elliptic curves and their zeros. There are two types, i.e., the pure non-abelian zetas defined using moduli spaces of semi-stable bundles, and the group zetas defined for special linear groups. In lower ranks, we show that these two types of zetas coincide and satisfy the Riemann Hypothesis. For general cases, exposed is an intrinsic relation on automorphism groups of semi-stable bundles over elliptic curves, the so-called counting miracle. All this, together with Harder-Narasimhan, Desale-Ramanan and Zagier's result, gives an effective way to count semi-stable bundles on elliptic curves not only in terms of automorphism groups but more essentially in terms of their $h^0$'s. Distributions of zeros of high rank zetas are also discussed.
Deformation Quantization of Principal Fibre Bundles and Classical Gauge Theories
Wei\\ss, Stefan
2010-01-01
In this dissertation the notion of deformation quantization of principal fibre bundles is established and investigated in order to find a geometric formulation of classical gauge theories on noncommutative space-times. As a generalization, the notion of deformation quantization of surjective submersions is also discussed. It is shown that deformation quantizations of surjective submersions and principal fibre bundles always exist and are unique up to equivalence. These statements concerning complex-valued functions are moreover formulated and proved for sections of arbitrary vector bundles over the total space, in particular equivariant vector bundles. The commutants of the deformed right module structures within the differential operators, playing an inportant role with regard to the infinitesimal gauge transformations, are computed explicitly in each case. Depending on the choice of specific covariant derivatives and connections the commutants are isomorphic to the formal power series of the respective vert...
T-duality for circle bundles via noncommutative geometry
Mathai, Varghese
2013-01-01
Recently Baraglia showed how topological T-duality can be extended to apply not only to principal circle bundles, but also to non-principal circle bundles. We show that his results can also be recovered via two other methods: the homotopy-theoretic approach of Bunke and Schick, and the noncommutative geometry approach which we previously used for principal torus bundles. This work has several interesting byproducts, including a study of the K-theory of crossed products by Isom(R), the universal cover of O(2), and some interesting facts about equivariant K-theory for Z/2. In the final section of this paper, these results are extended to the case of bundles with singular fibers, or in other words, non-free O(2)-actions.
Steric effects induce geometric remodeling of actin bundles in filopodia
Dobramysl, Ulrich; Erban, Radek
2016-01-01
Filopodia are ubiquitous fingerlike protrusions, spawned by many eukaryotic cells, to probe and interact with their environments. Polymerization dynamics of actin filaments, comprising the structural core of filopodia, largely determine their instantaneous lengths and overall lifetimes. The polymerization reactions at the filopodial tip require transport of G-actin, which enter the filopodial tube from the filopodial base and diffuse toward the filament barbed ends near the tip. Actin filaments are mechanically coupled into a tight bundle by cross-linker proteins. Interestingly, many of these proteins are relatively short, restricting the free diffusion of cytosolic G-actin throughout the bundle and, in particular, its penetration into the bundle core. To investigate the effect of steric restrictions on G-actin diffusion by the porous structure of filopodial actin filament bundle, we used a particle-based stochastic simulation approach. We discovered that excluded volume interactions result in partial and the...
Introductory lectures on fibre bundles and topology for physicists
International Nuclear Information System (INIS)
These lectures may provide useful background material for understanding gauge theories, particularly the nonperturbative effects such as instantons and monopoles. The mathematical language of topology and fibre bundles is introduced
Mechanical Models of Microtubule Bundle Collapse in Alzheimer's Disease
Sendek, Austin; Singh, Rajiv; Cox, Daniel
2013-03-01
Amyloid-beta aggregates initiate Alzheimer's disease, and downstream trigger degradation of tau proteins that act as microtubule bundle stabilizers and mechanical spacers. Currently it is unclear which of tau cutting by proteases, tau phosphorylation, or tau aggregation are responsible for cytoskeleton degradation., We construct a percolation simulation of the microtubule bundle using a molecular spring model for the taus and including depletion force attraction between microtubules and membrane/actin cytoskeletal surface tension. The simulation uses a fictive molecular dynamics to model the motion of the individual microtubules within the bundle as a result of random tau removal, and calculates the elastic modulus of the bundle as the tau concentration falls. We link the tau removal steps to kinetic tau steps in various models of tau degradation. Supported by US NSF Grant DMR 1207624
National Partnership for Maternal Safety Consensus Bundle on Obstetric Hemorrhage.
Main, Elliott K; Goffman, Dena; Scavone, Barbara M; Low, Lisa Kane; Bingham, Debra; Fontaine, Patricia L; Gorlin, Jed B; Lagrew, David C; Levy, Barbara S
2015-01-01
Hemorrhage is the most frequent cause of severe maternal morbidity and preventable maternal mortality and therefore is an ideal topic for the initial national maternity patient safety bundle. These safety bundles outline critical clinical practices that should be implemented in every maternity unit. They are developed by multidisciplinary work groups of the National Partnership for Maternal Safety under the guidance of the Council on Patient Safety in Women's Health Care. The safety bundle is organized into 4 domains: Readiness, Recognition and Prevention, Response, and Reporting and Systems Learning. Although the bundle components may be adapted to meet the resources available in individual facilities, standardization within an institution is strongly encouraged. References contain sample resources and "Potential Best Practices" to assist with implementation. PMID:26059199
National Partnership for Maternal Safety: consensus bundle on obstetric hemorrhage.
Main, Elliott K; Goffman, Dena; Scavone, Barbara M; Low, Lisa Kane; Bingham, Debra; Fontaine, Patricia L; Gorlin, Jed B; Lagrew, David C; Levy, Barbara S
2015-07-01
Hemorrhage is the most frequent cause of severe maternal morbidity and preventable maternal mortality and therefore is an ideal topic for the initial national maternity patient safety bundle. These safety bundles outline critical clinical practices that should be implemented in every maternity unit. They are developed by multidisciplinary work groups of the National Partnership for Maternal Safety under the guidance of the Council on Patient Safety in Women's Health Care. The safety bundle is organized into four domains: Readiness, Recognition and Prevention, Response, and Reporting and System Learning. Although the bundle components may be adapted to meet the resources available in individual facilities, standardization within an institution is strongly encouraged. References contain sample resources and "Potential Best Practices" to assist with implementation. PMID:26091046
Interactive hypermedia training manual for spent-fuel bundle counters
International Nuclear Information System (INIS)
Spent-fuel bundle counters, developed by the Canadian Safeguards Support Program for the International Atomic Energy Agency, provide a secure and independent means of counting the number of irradiated fuel bundles discharged into the fuel storage bays at CANDU nuclear power stations. Paper manuals have been traditionally used to familiarize IAEA inspectors with the operation, maintenance and extensive reporting capabilities of the bundle counters. To further assist inspectors, an interactive training manual has been developed on an Apple Macintosh computer using hypermedia software. The manual uses interactive animation and sound, in conjunction with the traditional text and graphics, to simulate the underlying operation and logic of the bundle counters. This paper presents the key features of the interactive manual and highlights the advantages of this new technology for training
Topological T-duality for torus bundles with monodromy
Baraglia, David
2015-05-01
We give a simplified definition of topological T-duality that applies to arbitrary torus bundles. The new definition does not involve Chern classes or spectral sequences, only gerbes and morphisms between them. All the familiar topological conditions for T-duals are shown to follow. We determine necessary and sufficient conditions for existence of a T-dual in the case of affine torus bundles. This is general enough to include all principal torus bundles as well as torus bundles with arbitrary monodromy representations. We show that isomorphisms in twisted cohomology, twisted K-theory and of Courant algebroids persist in this general setting. We also give an example where twisted K-theory groups can be computed by iterating T-duality.
Infinitely stably extendable vector bundles on projective spaces
Coanda, Iustin
2009-01-01
According to Horrocks (1966), a vector bundle E on the projective n-space extends stably to the projective N-space, N>n, if there exists a vector bundle on the larger space whose restriction to the smaller one is isomorphic to E plus a direct sum of line bundles. We show that E extends stably to the projective N-space for every N>n if and only if E is the cohomology of a free monad (with three terms). The proof uses the method of Coanda and Trautmann (2006). Combining this result with a theorem of Mohan Kumar, Peterson and Rao (2003), we get a new effective version of the Babylonian tower theorem for vector bundles on projective spaces.
SEU43 fuel bundle shielding analysis during spent fuel transport
Energy Technology Data Exchange (ETDEWEB)
Margeanu, C. A.; Ilie, P.; Olteanu, G. [Inst. for Nuclear Research Pitesti, No. 1 Campului Street, Mioveni 115400, Arges County (Romania)
2006-07-01
The basic task accomplished by the shielding calculations in a nuclear safety analysis consist in radiation doses calculation, in order to prevent any risks both for personnel protection and impact on the environment during the spent fuel manipulation, transport and storage. The paper investigates the effects induced by fuel bundle geometry modifications on the CANDU SEU spent fuel shielding analysis during transport. For this study, different CANDU-SEU43 fuel bundle projects, developed in INR Pitesti, have been considered. The spent fuel characteristics will be obtained by means of ORIGEN-S code. In order to estimate the corresponding radiation doses for different measuring points the Monte Carlo MORSE-SGC code will be used. Both codes are included in ORNL's SCALE 5 programs package. A comparison between the considered SEU43 fuel bundle projects will be also provided, with CANDU standard fuel bundle taken as reference. (authors)
Fuel rod bundles proposed for advanced pressure tube nuclear reactors
International Nuclear Information System (INIS)
The paper aims to be a general presentation for fuel bundles to be used in Advanced Pressure Tube Nuclear Reactors (APTNR). The characteristics of such a nuclear reactor resemble those of known advanced pressure tube nuclear reactors like: Advanced CANDU Reactor (ACRTM-1000, pertaining to AECL) and Indian Advanced Heavy Water Reactor (AHWR). We have also developed a fuel bundle proposal which will be referred as ASEU-43 (Advanced Slightly Enriched Uranium with 43 rods). The ASEU-43 main design along with a few neutronic and thermalhydraulic characteristics are presented in the paper versus similar ones from INR Pitesti SEU-43 and CANDU-37 standard fuel bundles. General remarks regarding the advantages of each fuel bundle and their suitability to be burned in an APTNR reactor are also revealed. (authors)
Design and synthesis of DNA four-helix bundles
Energy Technology Data Exchange (ETDEWEB)
Rangnekar, Abhijit; Gothelf, Kurt V [Department of Chemistry, Centre for DNA Nanotechnology (CDNA) and Interdisciplinary Nanoscience Center (iNANO), Aarhus University, DK-8000 Aarhus C (Denmark); LaBean, Thomas H, E-mail: kvg@chem.au.dk, E-mail: thl@cs.duke.edu [Department of Chemistry, Duke University, Durham, NC 27708 (United States)
2011-06-10
The field of DNA nanotechnology has evolved significantly in the past decade. Researchers have succeeded in synthesizing tile-based structures and using them to form periodic lattices in one, two and three dimensions. Origami-based structures have also been used to create nanoscale structures in two and three dimensions. Design and construction of DNA bundles with fixed circumference has added a new dimension to the field. Here we report the design and synthesis of a DNA four-helix bundle. It was found to be extremely rigid and stable. When several such bundles were assembled using appropriate sticky-ends, they formed micrometre-long filaments. However, when creation of two-dimensional sheet-like arrays of the four-helix bundles was attempted, nanoscale rings were observed instead. The exact reason behind the nanoring formation is yet to be ascertained, but it provides an exciting prospect for making programmable circular nanostructures using DNA.
Spring and stop assembly for nuclear fuel bundle
International Nuclear Information System (INIS)
A removable spring and stop assembly is described for use with a nuclear fuel bundle in a nuclear reactor core. The assembly includes a bolt threaded through a top section of a stop member by which the assembly (and a flow channel) is secured to the fuel bundle, the adjacent end threads of the bolt. The stop member is upset or deformed by which the bolt is captured in the assembly. (U.S.)
Design and verification of the 'GURI 01' bundle model
International Nuclear Information System (INIS)
This work presents a general description of the 'GURI 01' bundle model, designed by INVAP S.E., under international radioactive material transportation regulations, as a B(U) type bundle for international transportation up to a maximum of 350000 Ci of Co60. Moreover, the methodologies used and the results obtained from the structural evaluation of the mechanic essay and from the evaluation of the thermal behaviour under normal or accident conditions are briefly discussed. (Author)
Quantum principal bundles and Tannaka-Krein duality theory
Durdevic, M
1995-01-01
The structure of quantum principal bundles is studied, from the viewpoint of Tannaka-Krein duality theory. It is shown that if the structure quantum group is compact, principal G-bundles over a quantum space M are in a natural correspondence with certain contravariant functors defined on the category of finite-dimensional unitary representations of G, with the values in the category of finite projective bimodules over a *-algebra representing the base space.
Stable Parabolic Higgs Bundles as Asymptotically Stable Decorated Swamps
Beck, Nikolai
2014-01-01
Parabolic Higgs bundles can be described in terms of decorated swamps, which we studied in a recent paper. This description induces a notion of stability of parabolic Higgs bundles depending on a parameter, and we construct their moduli space inside the moduli space of decorated swamps. We then introduce asymptotic stability of decorated swamps in order to study the behavior of the stability condition as one parameter approaches infinity. The main result is the existence of a constant, such t...
Penurunan Kerugian Head pada Belokan Pipa dengan Peletakan Tube Bundle
Pratikto; Slamet Wahyudi
2010-01-01
Fluid flow flowing through an elbow causes separation. Separation leads to vortex, shake and cavity. As a result, the head loss will increase and the pipe installation is potentially damaged. Thus, separation must be eliminated. The separation is identified by the presence of high pressure decreasing in the downstream of elbow. To minimize the pressure decreasing in elbow, we need flow conditioner like a tube bundle. The aim of this research is to identify the influence of tube bundle placeme...
Quantized gauge-affine gravity in the superfiber bundle approach
Meziane, A.; Tahiri, M
2004-01-01
The quantization of gauge-affine gravity within the superfiber bundle formalism is proposed. By introducing an even pseudotensorial 1-superform over a principal superfibre bundle with superconnection, we obtain the geometrical Becchi-Rouet-Stora-Tyutin (BRST) and anti-BRST transformations of the fields occurring in such a theory. Reducing the four-dimensional general affine group double-covering to the Poincare group double-covering we also find the BRST and anti-BRST transformations of the f...
Intra-His bundle block: clinical, electrocardiographic, and electrophysiologic characteristics
Andréa Eduardo M.; Atié Jacob; Maciel Washington A.; Oliveira Jr Nilson A. de; Camanho Luiz Eduardo; Belo Luís Gustavo; Carvalho Hecio Affonso de; Siqueira Leonardo; Saad Eduardo; Venancio Ana Claudia
2002-01-01
OBJECTIVE: To assess the clinical, electrocardiographic, and electrophysiologic characteristics of patients (pt) with intra-His bundle block undergoing an electrophysiologic study (EPS). METHODS: We analyzed the characteristics of 16 pt with second-degree atrioventricular block and symptoms of syncope or dyspnea, or both, undergoing conventional EPS. RESULTS: Intra-His bundle block was documented in 16 pt during an EPS. In 15 (94%) pt, the atrioventricular block was recorded in sinus rhythm; ...
Countercurrent flow limitation experiments with full-scale bundle structures
International Nuclear Information System (INIS)
Atmospheric air/water experiments for VVER-440 and VVER-1000 fuel bundle structures have been carried out at different liquid heads above the perforated tie plate. Specific attention is given to countercurrent flow limitation across perforated upper tie plates in large channel geometries. The effects of the presence of the unheated fuel rod bundle and the thickness of the perforated plate on the countercurent flow behaviour have been observed. The found non-linear countercurrent flow behavior is discussed. (orig.)
Principal 2-bundles and their gauge 2-groups
Wockel, Christoph
2008-01-01
In this paper we introduce principal 2-bundles and show how they are classified by non-abelian Cech cohomology. Moreover, we show that their gauge 2-groups can be described by 2-group-valued functors, much like in classical bundle theory. Using this, we show that, under some mild requirements, these gauge 2-groups possess a natural smooth structure. In the last section we provide some explicit examples.
A classification of fibre bundles over 2-dimensional spaces
Kubyshin, Yu. A.
1999-01-01
The classification problem for principal fibre bundles over two-dimensional CW-complexes is considered. Using the Postnikov factorization for the base space of a universal bundle a Puppe sequence that gives an implicit solution for the classification problem is constructed. In cases, when the structure group $G$ is path-connected or $\\pi_{1}(G) = 0$, the classification can be given in terms of cohomology groups.
Filler metals for containers holding irradiated fuel bundles
International Nuclear Information System (INIS)
One of the procedures being considered for the disposal of Canadian deuterium uranium (CANDU) irradiated fuel bundles is to place the bundles in containers, fill the containers with metal, and place them underground. This investigation deals with the selection of the filler metal with particular reference to the reaction rate with, and bonding of the filler metal to, the fuel sheathing (Zircaloy 4) and potential container materials. Lead, zinc, and aluminium alloys were examined as potential filler metals. (U.K.)
Optimal Bundle of Multimedia Services in Emerging Mobile Markets
Lee, ChanGi; Lee, SeongCheol; Lee, DeockHee; Lee, HyeongJik
2006-01-01
Although various emerging technologies have been launched, they present limitations as far as offering full-scale ubiquitous services independently is concerned. In view of this fact, service providers are likely to provide bundled services among possible combinations of services. Indeed, making a timely decision regarding the value maximization of bundled service is directly related to service providers' future growth and success in the turbulent market environment. This paper aims to find t...
Fuel temperature characteristics of the 37-element and CANFLEX fuel bundle
International Nuclear Information System (INIS)
This report describes the fuel temperature characteristics of CANFLEX fuel bundles and 37-element fuel bundles for a different burnup of fuel. The program was consisted for seeking the fuel temperature of fuel bundles of CANFLEX fuel bundles and 37-element fuel bundles by using the method in NUCIRC. Fuel temperature has an increasing pattern with the burnup of fuel for CANFLEX fuel bundles and 37-element fuel bundles. For all the case of burnup, the fuel temperature of CANFLEX fuel bundles has a lower value than that of 37-element fuel bundles. Especially, for the high power channel, the CANFLEX fuel bundles show a lower fuel temperature as much as about 75 degree, and the core averaged fuel temperature has a lower fuel temperature of about 50 degree than that of 37-element fuel bundles. The lower fuel temperature of CANFLEX fuel bundles is expected to enhance the safety by reducing the fuel temperature coefficient. Finally, for each burnup of CANFLEX fuel bundles and 37-element fuel bundles, the equation was present for predicting the fuel temperature of a bundle in terms of a coolant temperature and bundle power
Bucher, Michelle; Campagnolo, Caterina
2016-01-01
We present three new inequalities tying the signature, the simplicial volume and the Euler characteristic of surface bundles over surfaces. Two of them are true for any surface bundle, while the third holds on a specific family of surface bundles, namely the ones that arise through a ramified covering. These are the main known examples of bundles with non-zero signature.
Plantain fibre bundles isolated from Colombian agro-industrial residues.
Gañán, Piedad; Zuluaga, Robin; Restrepo, Adriana; Labidi, Jalel; Mondragon, Iñaki
2008-02-01
Comestible fruit production from Musaceas plants is an important economical activity in developing countries like Colombia. However, it generates a large amount of agro-industrial residues. Some of them are a potential resource of natural fibres, which can be used as reinforcement for composite materials. In this work, a series of commercial plantain (Musa AAB, cv "Dominico Harton") fibre bundles extracted from pseudostem, leaf sheath and rachis agricultural wastes were analyzed. Mechanical decortication and biological retting processes were used during fiber extraction. No significant differences in composition of vascular bundles were observed for both extraction processes. Gross morphological characteristics and mechanical behavior have been evaluated. Conducting tissues with spiral-like arrangement are observed attached to fibre bundles. This fact suggests a big amount of these tissues in commercial plantain plants. Both used extraction methods are not enough to remove them. Pseudostem fibre bundles have higher specific strength and modulus and lower strain at break than leaf sheath and rachis fibre bundles, having values comparable to other lignocellulosic fibres bundles. PMID:17350832
A Radiologist's Primer on Bundles and Care Episodes.
Seidenwurm, David; Lexa, Frank James
2016-09-01
Bundled or episode payments are among the most heavily emphasized approaches to aligning incentives and promoting care coordination, efficiency, and accountability in health care redesign. Bundled or episode payments price a market basket of services for an entire episode of care with both a clearly defined trigger and termination. Because the radiologist is "ancillary" in many bundles, the specialty is often unaware of the phenomenon. This is likely to change rapidly. Radiology is pivotal in high-prevalence, high-impact care areas such as low back pain and stroke that are focuses of widely used system performance metrics. More important, radiology is central to the diagnosis and management of a wide range of important diagnostic issues in areas such as breast cancer, pulmonary nodules, and incidental findings. Three models of bundled care will probably involve radiology intimately in the near future. Pure radiology bundles might be constructed for breast cancer screening and diagnosis, and these could be priced on the basis of guideline-based best-practice frequencies of care events such as recall and biopsy. Clinical bundles, for example low back pain, could be priced on the basis of optimal imaging frequencies. Finally, pricing of imaging studies might include evidence-based frequencies of follow-up imaging for incidental findings. PMID:27210231
Design and fabrication of a remote fuel bundle welding system
International Nuclear Information System (INIS)
A remote fuel bundle welding system in the hot-cell was designed and fabricated. To achieve this, a preliminary investigation of a hands-on fuel fabrication outside the hot-cell was conducted with a consideration of the constraints caused by welding in the hot-cell. Some basic experiments were also carried out to improve the end-plate welding process for fuel bundle manufacturing. The resistance welding system using the end-plate welding was also improved. It was found that resistance welding was more suitable for joining and end-plate to end caps in the hot-cell. The optimum conditions for end-plate welding for remote operation were also obtained. Preliminary performances to improve the resistance welding process were also examined, and the resistance welding process was determined to be the best in the hot-cell environment for fuel bundle manufacturing. The greatest advantage of fuel bundle welding system would be a qualified process for resistance welding in which there is extensive production experience. This paper presents an outline of the developed welding system for fuel bundle manufacturing and reviews the conceptual design of remote welding system using a master-slave manipulator. The design of a remote welding system using the 3-dimensional modeling method was also designed. Furthermore the mechanical considerations and the mock-up simulation test were described. Finally, its performance test results were presented for a mock-up of a remote fuel bundle welding system. (Author)
Jacobi Matthias; Magnussen Robert A; Villa Vincent; Demey Guillaume; Neyret Philippe
2012-01-01
Abstract Background There is significant interest in the restoration of the double-bundle anatomy of the native ACL when performing ACL reconstruction. Possible techniques include those utilizing two separate grafts with independent tunnels and those that attempt to mimic this anatomy with a single graft and fewer tunnels. Many of the latter techniques require specific instrumentation and are technically challenging. We demonstrate that the double-bundle anatomy of the native ACL can theoreti...
How Buyers Evaluate Product Bundles: A Model of Anchoring and Adjustment.
Yadav, Manjit S
1994-01-01
Bundling, the joint offering of two or more items, is a common selling strategy, yet little research has been conducted on buyers' evaluation of bundle offers. We developed and tested a model of bundle evaluation in which the buyers anchored their evaluation on the item perceived as most important and then made adjustments on the basis of their evaluations of the remaining bundle items. The results of two computerized laboratory experiments suggested that people tend to examine bundle items i...
Combustor having mixing tube bundle with baffle arrangement for directing fuel
Energy Technology Data Exchange (ETDEWEB)
Hughes, Michael John; McConnaughhay, Johnie Franklin
2016-08-23
A combustor includes a tube bundle that extends radially across at least a portion of the combustor. The tube bundle includes an upstream surface axially separated from a downstream surface, and a plurality of tubes extend from the upstream surface through the downstream surface to provide fluid communication through the tube bundle. A barrier extends radially inside the tube bundle between the upstream and downstream surfaces, and a baffle extends axially inside the tube bundle between the upstream surface and the barrier.
Hagg, Heather (Woodward); El-Harit, Jamie; Vanni, Chris; Scott, Penny
2007-01-01
Within healthcare, clinical practice bundles have been used to implement standardized, nursing driven protocols resulting in standardized patient care and improved patient outcomes. Examples of these types of bundles include clinical practices shown through evidence based medicine to reduce occurrences of Ventilator Associated Pneumonia – VAP bundle; those shown to reduce the occurrences of central line infections – CL bundle; and those shown to significantly improve the outcomes of patients...
Location of test bundle instrumentation and anticipated experimental values for the CFTL AG-1 bundle
International Nuclear Information System (INIS)
The placement of instrumentation within the Core Flow Test Loop (CFTL) AG-1 test section to meet the following objectives is described. The objectives are threefold: (1) to provide values for the evaluation of the performance of the test section, (2) to compare the experimental data with value determined by pretest calulations to indicate the approach to conditions that can lead to a bundle failure, and (3) to acquire data during testing that will form a data base for subsequent use in the verification of computational procedures used in the licensing of the Gas-Cooled Fast Reactor. Anticipated values for the various instruments have been determined using the computational procedure SAGAPO modified for the AG-1 geometry. These results are used as the basis for the specification of differential pressure cells and the range of readings anticipated from the thermocouples. Part of the results for the full-flow, full-power case is presented
Aerosol retention in the flooded steam generator bundle during SGTR
International Nuclear Information System (INIS)
Research highlights: → High retention of aerosol particles in a steam generator bundle flooded with water. → Increasing particle inertia, i.e., particle size and velocity, increases retention. → Much higher retention of aerosol particles in the steam generator bundle flooded with water than in a dry bundle. → Much higher retention of aerosol particles in the steam generator bundle than in a bare pool. → Bare pool models have to be adapted to be applicable for flooded bundles. - Abstract: A steam generator tube rupture in a pressurized water reactor may cause accidental release of radioactive particles into the environment. Its specific significance is in its potential to bypass the containment thereby providing a direct pathway of the radioactivity from the primary circuit to the environment. Under certain severe accident scenarios, the steam generator bundle may be flooded with water. In addition, some severe accident management procedures are designed to minimize the release of radioactivity into the environment by flooding the defective steam generator secondary side with water when the steam generator has dried out. To extend our understanding of the particle retention phenomena in the flooded steam generator bundle, tests were conducted in the ARTIST and ARTIST II programs to determine the effect of different parameters on particle retention. The effects of particle type (spherical or agglomerate), particle size, gas mass flow rate, and the break submergence on particle retention were investigated. Results can be summarized as follows: increasing particle inertia was found to increase retention in the flooded bundle. Particle shape, i.e., agglomerate or spherical structure, did not affect retention significantly. Even with a very low submergence, 0.3 m above the tube break, significant aerosol retention took place underlining the importance of the jet-bundle interactions close to the tube break. Droplets were entrained from the water surface with
Directory of Open Access Journals (Sweden)
Sandra Umeda Sasaki
2008-01-01
Full Text Available INTRODUCTION: Anterior cruciate ligament ruptures are frequent, especially in sports. Surgical reconstruction with autologous grafts is widely employed in the international literature. Controversies remain with respect to technique variations as continuous research for improvement takes place. One of these variations is the anatomical double bundle technique, which is performed instead of the conventional single bundle technique. More recently, there has been a tendency towards positioning the two bundles through double bone tunnels in the femur and tibia (anatomical reconstruction. OBJECTIVES: To compare, through biomechanical tests, the practice of anatomical double bundle anterior cruciate ligament reconstruction with a patellar graft to conventional single bundle reconstruction with the same amount of patellar graft in a paired experimental cadaver study. METHODS: Nine pairs of male cadaver knees ranging in age from 44 to 63 years were randomized into two groups: group A (single bundle and group B (anatomical reconstruction. Each knee was biomechanically tested under three conditions: intact anterior cruciate ligament, reconstructed anterior cruciate ligament, and injured anterior cruciate ligament. Maximum anterior dislocation, rigidity, and passive internal tibia rotation were recorded with knees submitted to a 100 N horizontal anterior dislocation force applied to the tibia with the knees at 30, 60 and 90 degrees of flexion. RESULTS: There were no differences between the two techniques for any of the measurements by ANOVA tests. CONCLUSION: The technique of anatomical double bundle reconstruction of the anterior cruciate ligament with bone-patellar tendon-bone graft has a similar biomechanical behavior with regard to anterior tibial dislocation, rigidity, and passive internal tibial rotation.
Modelling of transient dynamic bundle deformation using time integration scheme
International Nuclear Information System (INIS)
The BOW code has been examined whether its modeling capability can be extended to the simulation of interactions (i.e., fretting) between neighbouring fuel elements in a fuel bundle and between the fuel bundle and the pressure tube in a fuel channel. The current BOW code is specialized in simulating the static problems, such as the deflection of each element and interactions between neighbouring elements in a fuel bundle, and interactions between neighbouring bundles and between a bundle and the pressure tube in a fuel channel. The Wilson θ time integration scheme has been implemented in the BOW code, for the extension of its capability to modelling dynamic contact problems. As part of verification to ensure that the modification in the code functions exactly as designed, the dynamic-modelling capability of the BOW code has been applied to simple support beam cases subjected to a uniform step load at the middle of the beam. The calculation results confirmed that the modified BOW code, where the contact algorithm is implemented in the step-by-step integration manner using the Wilson θ time integration scheme, can solve the dynamic problem with unconditional convergence. This paper describes the theory and models for the new capabilities of the BOW code. (author)
Experimental study for convective heat transfer of staged tube bundles
International Nuclear Information System (INIS)
The lack of potable water is one of the most serious problems the world is facing at present. SMART which is a 330 MWt advanced integral PWR, was developed by the KAERI for electricity generation and seawater desalination. SMART adopted a passive system to enhance its safety. The passive system can passively remove a decay heat from a reactor core to an emergency cooldown tank through the heat exchanger. Tube bundles of the heat exchanger, which is submerged in an emergency cooldown tank, transfer heat to an emergency cooldown tank by natural circulation. Heat transfer tests for the upward straight tube bundle were performed to confirm the capability of the SMART design under natural circulation conditions. The heat transfer at the tube bundle was affected by the fluid temperature in the emergency cooldown tank and the radial location of tube bundle. However, it had nearly the same value at the inlet region regardless of the tube location. The average heat transfer at the tube bundle was slightly higher than that at the single tube. (author)
Thermal hydraulics of rod bundles: The effect of eccentricity
International Nuclear Information System (INIS)
Highlights: • Present CFD investigation explores, whole bundle eccentricity for the first time. • Fluid flow and thermal characteristics in various subchannels are analyzed. • Mass flux distribution is particularly analyzed to study eccentricity effect. • Higher eccentricity resulted in a shoot up in rod surface temperature distribution. • Both tangential and radial flow in rod bundles has resulted due to eccentricity. -- Abstract: The effect of eccentricity on the fluid flow and heat transfer through a 19-rod bundle is numerically carried out. When the whole bundle shifts downwards with respect to the outer (pressure) tube, flow redistribution happens. This in turn is responsible for changes in mass flux, pressure and differential flow development in various subchannels. The heat flux imposed on the surface of the fuel rods and the mass flux through the subchannels determines the coolant outlet temperatures. The simulations are performed for a coolant flow Reynolds number of 4 × 105. For an eccentricity value of 0.7, the mass flux in the bottom most subchannel (l) was found to decrease by 10%, while the surface temperature of the fuel rod in the vicinity of this subchannel increased by 250% at the outlet section. Parameters of engineering interest including skin friction coefficient, Nusselt number, etc., have been systematically explored to study the effect of eccentricity on the rod bundle
Study Of The PWR Fuel Bundle Characteristic With Borated Water
International Nuclear Information System (INIS)
Study of the PWR fuel bundle characteristic with 2,4, 2,6, 2,8, 3,0, 3,2 and 3,4 enrichment also with borated water 150 and 200 ppm has been done. The fuel bundle contained 264 fuel elements and water (no fuel elements) are arranged as 17 x 17 matrix and 30,294 cm. The fuel bundle characteristic can be seen from their group constants and the infinite multiplication factor whether more or less than one. The fuel bundle parameters can be found from cell calculation with WIMS PC version program. From the cell calculation shown that the infinite multiplication factor of the fuel bundle with 2,4% enrichment and 200 ppm borated water is 1, 01672, its shown that infinite multiplication factor will less than one with increasing borated water more than 200 ppm. From these result if we would like to design the reactor core with 2,4% minimum enrichment then the maximum borated water is 200 ppm
Hair-bundle friction from transduction channels' gating forces
Bormuth, Volker; Barral, Jérémie; Joanny, Jean-François; Jülicher, Frank; Martin, Pascal
2015-12-01
Hearing starts when sound-evoked mechanical vibrations of the hair-cell bundle activate mechanosensitive ion channels, giving birth to an electrical signal. As for any mechanical system, friction impedes movements of the hair bundle and thus constrains the sensitivity and frequency selectivity of auditory transduction. We have shown recently that the opening and closing of the transduction channels produce internal frictional forces that can dominate viscous drag on the micrometer-sized hair bundle and thus provide a major source of damping [2]. We develop here a physical theory of passive hair-bundle mechanics that explains the origin of channel friction. We show that channel friction can be understood quantitatively by coupling the dynamics of the conformational change associated with channel gating to tip-link tension. As a result, varying channel properties affects friction, with faster channels producing smaller friction. The analysis emphasizes the dual role of transduction channels' gating forces, which affect both hair-bundle stiffness and drag. Friction originating from gating of ion channels is a general concept that is relevant to all mechanosensitive channels.
Symposium on Singularities, Representation of Algebras, and Vector Bundles
Trautmann, Günther
1987-01-01
It is well known that there are close relations between classes of singularities and representation theory via the McKay correspondence and between representation theory and vector bundles on projective spaces via the Bernstein-Gelfand-Gelfand construction. These relations however cannot be considered to be either completely understood or fully exploited. These proceedings document recent developments in the area. The questions and methods of representation theory have applications to singularities and to vector bundles. Representation theory itself, which had primarily developed its methods for Artinian algebras, starts to investigate algebras of higher dimension partly because of these applications. Future research in representation theory may be spurred by the classification of singularities and the highly developed theory of moduli for vector bundles. The volume contains 3 survey articles on the 3 main topics mentioned, stressing their interrelationships, as well as original research papers.
Real Parabolic Vector Bundles over a Real Curve
Indian Academy of Sciences (India)
Sanjay Amrutiya
2014-02-01
We define real parabolic structures on real vector bundles over a real curve. Let $(X, _X)$ be a real curve, and let $S\\subset X$ be a non-empty finite subset of such that $_X(S) = S$. Let ≥ 2 be an integer. We construct an -fold cyclic cover : $Y→ X$ in the category of real curves, ramified precisely over each point of , and with the property that for any element of the Galois group , and any $y\\in Y$, one has $_Y(gy) = g^{-1}_Y(y)$. We established an equivalence between the category of real parabolic vector bundles on $(X,_X)$ with real parabolic structure over , all of whose weights are integral multiples of 1/, and the category of real -equivariant vector bundles on $(Y, _Y)$.
β-Peptide bundles: Design. Build. Analyze. Biosynthesize.
Wang, Pam S P; Schepartz, Alanna
2016-06-14
Peptides containing β-amino acids are unique non-natural polymers known to assemble into protein-like tertiary and quaternary structures. When composed solely of β-amino acids, the structures formed, defined assemblies of 14-helices called β-peptide bundles, fold cooperatively in water solvent into unique and discrete quaternary assemblies that are highly thermostable, bind complex substrates and metal ion cofactors, and, in certain cases, catalyze chemical reactions. In this Perspective, we recount the design and elaboration of β-peptide bundles and provide an outlook on recent, unexpected discoveries that could influence research on β-peptides and β-peptide bundles (and β-amino acid-containing proteins) for decades to come. PMID:27146019
Simulation of bundle test Quench-12 with integral code MELCOR
International Nuclear Information System (INIS)
The past NRI analyses cover the Quench-01, Quench-03 and Quench-06 with version MELCOR 1.8.5 (including reflood model), and Quench-01 and Quench-11 tests with the latest version MELCOR 1.8.6. The Quench-12 test is specific, because it has different bundle configuration related to the VVER bundle configuration with hexagonal grid of pins and also used E110 cladding material. Specificity of Quench-12 test is also in the used material of fuel rod cladding - E110. The test specificities are a reason for the highest concern, because the VVER reactors are operated in the Czech Republic. The new input model was developed with the taking into account all experience from previous simulations of the Quench bundle tests. The recent version MELCOR 1.8.6 YU2911 was used for the simulation with slightly modified ELHEAT package. Sensitivity studies on input parameters and oxidation kinetics were performed. (author)
Gradient Bundle Analysis: A Full Topological Approach to Chemical Bonding
Morgenstern, Amanda
2016-01-01
The "chemical bond" is a central concept in molecular sciences, but there is no consensus as to what a bond actually is. Therefore, a variety of bonding models have been developed, each defining the structure of molecules in a different manner with the goal of explaining and predicting chemical properties. This thesis describes the initial development of gradient bundle analysis (GBA), a chemical bonding model that creates a high resolution picture of chemical interactions within the charge density framework. GBA is based on concepts from the quantum theory of atoms in molecules (QTAIM), but uses a more complete picture of the topology and geometry of the electron charge density to understand and predict bonding interactions. Gradient bundles are defined as volumes bounded by zero-flux surfaces (ZFSs) in the gradient of the charge density with well-defined energies. The structure of gradient bundles provides an avenue for detecting the locations of valence electrons, which correspond to reactive regions in a ...
Multi-scale strain-stiffening of semiflexible bundle networks
Piechocka, I K; Broedersz, C P; Kurniawan, N A; MacKintosh, F C; Koenderink, G H
2015-01-01
Bundles of polymer filaments are responsible for the rich and unique mechanical behaviors of many biomaterials, including cells and extracellular matrices. In fibrin biopolymers, whose nonlinear elastic properties are crucial for normal blood clotting, protofibrils self-assemble and bundle to form networks of semiflexible fibers. Here we show that the extraordinary strain-stiffening response of fibrin networks is a direct reflection of the hierarchical architecture of the fibrin fibers. We measure the rheology of networks of unbundled protofibrils and find excellent agreement with an affine model of extensible wormlike polymers. By direct comparison with these data, we show that physiological fibrin networks composed of thick fibers can be modeled as networks of tight protofibril bundles. We demonstrate that the tightness of coupling between protofibrils in the fibers can be tuned by the degree of enzymatic intermolecular crosslinking by the coagulation Factor XIII. Furthermore, at high stress, the protofibri...
Evaluation of phenomenological DNB models for rod bundle geometries
International Nuclear Information System (INIS)
Seven phenomenological DNB models based on the liquid sublayer dryout and the bubble crowding mechanisms have been evaluated for the square array rod bundles at PWR conditions. The local thermal hydraulic conditions were calculated by the COBRA-IV-I code, and it was assumed that the enthalpy and mass velocity distribution in the test bundle would not be changed at different power levels. A simplified method, which has been proposed for the prediction of CHF in rod bundles from round tube CHF correlations without detailed subchannel analyses, was also applied with the phenomenological models. In view of the prediction accuracy and the applicable range, Lin model shows the best result among phenomenological DNB models assessed in this study. The parametric trends of phenomenological DNB models, however are somewhat abnormal comparing to experimental data. So it can be argued that the existing phenomenological DNB models are rather empirical than theoretical so far
Magnetic Propulsion of Microswimmers with DNA-Based Flagellar Bundles.
Maier, Alexander M; Weig, Cornelius; Oswald, Peter; Frey, Erwin; Fischer, Peer; Liedl, Tim
2016-02-10
We show that DNA-based self-assembly can serve as a general and flexible tool to construct artificial flagella of several micrometers in length and only tens of nanometers in diameter. By attaching the DNA flagella to biocompatible magnetic microparticles, we provide a proof of concept demonstration of hybrid structures that, when rotated in an external magnetic field, propel by means of a flagellar bundle, similar to self-propelling peritrichous bacteria. Our theoretical analysis predicts that flagellar bundles that possess a length-dependent bending stiffness should exhibit a superior swimming speed compared to swimmers with a single appendage. The DNA self-assembly method permits the realization of these improved flagellar bundles in good agreement with our quantitative model. DNA flagella with well-controlled shape could fundamentally increase the functionality of fully biocompatible nanorobots and extend the scope and complexity of active materials. PMID:26821214
Stable parabolic Higgs bundles as asymptotically stable decorated swamps
Beck, Nikolai
2016-06-01
Parabolic Higgs bundles can be described in terms of decorated swamps, which we studied in a recent paper. This description induces a notion of stability of parabolic Higgs bundles depending on a parameter, and we construct their moduli space inside the moduli space of decorated swamps. We then introduce asymptotic stability of decorated swamps in order to study the behaviour of the stability condition as one parameter approaches infinity. The main result is the existence of a constant, such that stability with respect to parameters greater than this constant is equivalent to asymptotic stability. This implies boundedness of all decorated swamps which are semistable with respect to some parameter. Finally, we recover the usual stability condition of parabolic Higgs bundles as asymptotic stability.
Quillen Bundle and Geometric Prequantization of Non-Abelian Vortices on a Riemann Surface
Indian Academy of Sciences (India)
Rukmini Dey; Samir K Paul
2011-02-01
In this paper we prequantize the moduli space of non-abelian vortices. We explicitly calculate the symplectic form arising from 2 metric and we construct a prequantum line bundle whose curvature is proportional to this symplectic form. The prequantum line bundle turns out to be Quillen’s determinant line bundle with a modified Quillen metric. Next, as in the case of abelian vortices, we construct line bundles over the moduli space whose curvatures form a family of symplectic forms which are parametrized by $\\Psi_0$, a section of a certain bundle. The equivalence of these prequantum bundles are discussed.
The Determinant Bundle on the Moduli Space of Stable Triples over a Curve
Indian Academy of Sciences (India)
Indranil Biswas; N Raghavendra
2002-08-01
We construct a holomorphic Hermitian line bundle over the moduli space of stable triples of the form (1, 2, ), where 1 and 2 are holomorphic vector bundles over a fixed compact Riemann surface , and : 2 → 1 is a holomorphic vector bundle homomorphism. The curvature of the Chern connection of this holomorphic Hermitian line bundle is computed. The curvature is shown to coincide with a constant scalar multiple of the natural Kähler form on the moduli space. The construction is based on a result of Quillen on the determinant line bundle over the space of Dolbeault operators on a fixed ∞ Hermitian vector bundle over a compact Riemann surface.
BUNDLE ADJUSTMENTS CCD CAMERA CALIBRATION BASED ON COLLINEARITY EQUATION
Institute of Scientific and Technical Information of China (English)
Liu Changying; Yu Zhijing; Che Rensheng; Ye Dong; Huang Qingcheng; Yang Dingning
2004-01-01
The solid template CCD camera calibration method of bundle adjustments based on collinearity equation is presented considering the characteristics of space large-dimension on-line measurement. In the method, a more comprehensive camera model is adopted which is based on the pinhole model extended with distortions corrections. In the process of calibration, calibration precision is improved by imaging at different locations in the whole measurement space, multi-imaging at the same location and bundle adjustments optimization. The calibration experiment proves that the calibration method is able to fulfill calibration requirement of CCD camera applied to vision measurement.
Failure process of a bundle of plastic fibers
F. Raischel; Kun, F; Herrmann, H. J.
2006-01-01
We present an extension of fiber bundle models considering that failed fibers still carry a fraction $0 \\leq \\alpha \\leq 1$ of their failure load. The value of $\\alpha$ interpolates between the perfectly brittle failure $(\\alpha = 0)$ and perfectly plastic behavior $(\\alpha=1)$ of fibers. We show that the finite load bearing capacity of broken fibers has a substantial effect on the failure process of the bundle. In the case of global load sharing it is found that for $\\alpha \\to 1$ the macros...
Capillary Micro-Flow Through a Fiber Bundle(Ⅰ)
Institute of Scientific and Technical Information of China (English)
ZHU Ying-dan; WANG Ji-hui; TAN Hua; GAO Guo-qiang
2004-01-01
The present work considered the capillary micro-flow through a fiber bundle. The resin heights in the fiber bundle as a function of time were used to determine the experimental values of capillary pressure and the permeability by the nonlinear regression fitting method. The fitting curves showed a good agreement with experiments. However, these values of capillary pressure from short- time experiments were much lower than the theoretical results from the Yang-Laplace Equation. More accurate capillary pressure was predicted from the presented long-run experiment.
Stable bundles of rank 2 with 4 sections
Grzegorczyk, I; Newstead, P E
2010-01-01
This paper contains results on stable bundles of rank $2$ with space of sections of dimension $4$ on a smooth irreducible projective algebraic curve $C$. There is a known lower bound on the degree for the existence of such bundles; the main result of the paper is a geometric criterion for this bound to be attained. For a general curve $C$ of genus $10$, we show that the bound cannot be attained, but that there exist Petri curves of this genus for which the bound is sharp. We interpret the main results for various curves and in terms of Clifford indices and coherent systems.
Stable bundles of rank 2 with 4 sections
Grzegorczyk, I.; Mercat, V.; Newstead, P. E.
2010-01-01
This paper contains results on stable bundles of rank 2 with space of sections of dimension 4 on a smooth irreducible projective algebraic curve $C$. There is a known lower bound on the degree for the existence of such bundles; the main result of the paper is a geometric criterion for this bound to be attained. For a general curve $C$ of genus 10, we show that the bound cannot be attained, but that there exist Petri curves of this genus for which the bound is sharp. We interpret the main resu...
ASSERT and COBRA predictions of flow distribution in vertical bundles
International Nuclear Information System (INIS)
COBRA and ASSERT are subchannel codes which compute flow and enthalpy distributions in rod bundles. COBRA is a well known code, ASSERT is under development at CRNL. This paper gives a comparison of the two codes with boiling experiments in vertical seven rod bundles. ASSERT predictions of the void distribution are shown to be in good agreement with reported experimental results, while COBRA predictions are unsatisfactory. The mixing models in both COBRA and ASSERT are briefly discussed. The reasons for the failure of COBRA-IV and the success of ASSERT in simulating the experiments are highlighted
Validation of SOCRAT-BN code on rod bundle experiments
International Nuclear Information System (INIS)
SOCRAT-BN code is developed for the analysis of design and beyond design basis accidents at NPPs with liquid sodium as a coolant. To simulate the behavior of the coolant in the reactor core heat transfer and friction in rod bundle geometry are required to consider. The code SOCRAT-BN uses specialized closing relations to simulate rod bundles. The article describes the validation of the code SOCRAT-BN on experiments with fuel rod imitators in the triangular geometry with a wire-wound. (author)
Reaction–diffusion model of hair-bundle morphogenesis
Jacobo, Adrian; Hudspeth, A. J.
2014-01-01
Our senses of hearing and balance rest upon the activity of hair cells, the ear’s sensory receptors. Each hair cell detects mechanical stimuli with its hair bundle, an organelle comprising 10–300 cylindrical, actin-filled stereocilia. A bundle’s structure is highly stereotyped: the stereocilia stand erect in a regular, hexagonal array and display a monotonic gradient in length along one axis. This precise organization is key to the operation of the hair bundle: mutations that disturb the morp...
Chop-leach fuel bundle residues densification by melting
Energy Technology Data Exchange (ETDEWEB)
Nelson, R.G.; Griggs, B.
1976-11-01
Two melting processes were investigated for the densification of fuel bundle residues: Industoslag melting and graphite crucible melting. The Industoslag process, with prior decontamination and sorting, can produce ingots of Zircaloy, stainless steel and Inconel of a quality suitable for refabrication and reuse. The process can also melt oxidized mixtures of fuel bundle residues for direct storage. Eutectic mixtures of these materials can be melted in graphite at temperatures of 1300/sup 0/C. Hydrogen absorption experiments with the zirconium-rich alloys show the alloys to be potential tritium reservoirs. 13 figures.
Shear and friction between carbon nanotubes in bundles and yarns.
Paci, Jeffrey T; Furmanchuk, Al'ona; Espinosa, Horacio D; Schatz, George C
2014-11-12
We perform a detailed density functional theory assessment of the factors that determine shear interactions between carbon nanotubes (CNTs) within bundles and in related CNT and graphene structures including yarns, providing an explanation for the shear force measured in recent experiments (Filleter, T. etal. Nano Lett. 2012, 12, 73). The potential energy barriers separating AB stacked structures are found to be irrelevant to the shear analysis for bundles and yarns due to turbostratic stacking, and as a result, the tube-tube shear strength for pristine CNTs is estimated to be manufacture of strong yarns composed of CNTs. PMID:25279773
Phase Space Reduction of Star Products on Cotangent Bundles
Kowalzig, Niels; Neumaier, Nikolai; Pflaum, Markus J.
2004-01-01
In this paper we construct star products on Marsden-Weinstein reduced spaces in case both the original phase space and the reduced phase space are (symplectomorphic to) cotangent bundles. Under the assumption that the original cotangent bundle $T^*Q$ carries a symplectique structure of form $\\omega_{B_0}=\\omega_0 + \\pi^*B_0$ with $B_0$ a closed two-form on $Q$, is equipped by the cotangent lift of a proper and free Lie group action on $Q$ and by an invariant star product that admits a $G$-equ...
Study on Unigraphics Drawing Modeling Method for 37-Element and CANFLEX Fuel Bundle
International Nuclear Information System (INIS)
The CANFLEX bundle contains 43 elements of two different diameters. It has two rings of small diameter elements on the outside, and eight elements (with diameter slightly larger than those in the standard 37-Element bundle) in the center. This larger number of small diameter elements on the outside of the CANFLEX bundle enhances thermo-hydraulic capability, resulting in a higher power capability and an improvement in operating safety margins. As a Result of advanced fuel design for CANFLEX fuel bundles, components consisting of fuel bundles are more complicated. Hence, the detailed modeling of components is inevitable in order to analyze the fuel performance by computational fluid dynamics. In this report, the basic design of the advanced fuel for CANDU reactors was carried out and the methodology for the modeling of fuel bundle were described. Firstly, the components consisting of fuel bundles were separately modeled and saved with different file names. The final feature of fuel bundle was accomplished by an assembling process of components. Since this report developed the modeling methodology based on the Unigraphics program, the basic explanations for the software were given first, and the complete modeling of 37-elements and CANFLEX fuel bundles were provided. The components of CANFLEX fuel bundles were also compared with that of 37-elements fuel bundles. Although, in this report, the modeling methodology is applied only to 37-elements and CANFLEX fuel bundles, this methodology may be applicable to the newly designed fuel bundles which are to be developed in the future
The effect of radial power profile of DUPIC bundle on CHF
International Nuclear Information System (INIS)
The axial and ring power profiles of DUPIC bundle are much different from those of reference 37-element fuel bundle since a DUPIC fuel bundle is re-fabricated using spent PWR fuel and 2-bundle shift refuelling scheme is proposed to CANDU-6 reactor. In case that the ring power profile of a fuel bundle is altered, the flow and enthalpy distribution of subchannels and the radial position of CHF occurrence will be changed. Similarly, the axial power profile of a fuel channel affects CHF and axial position of CHF occurrence as well as axial enthalpy, quality and pressure distribution. The ring power profile of the DUPIC bundle as increasing burnup is altered and flattened compared to 37-element bundle and each fuel bundle in a fuel channel has a different ring power profile from the other bundles at different axial position in the same fuel channel. Therefore, how to consider the burnup or ring power effect on CHF is very important to DUPIC thermalhydraulic analysis. At present study, thermalhydraulic analysis of the DUPIC bundle was performed in consideration of ring power profile effect on CHF. The subchannel enthalpy, mass flux and CHF distribution for 0 burnup to discharged burnup (18,000 MWD/THM) of DUPIC bundle were evaluated using ASSERT subchannel code. The results were compared to those of 37-element bundle and the compatability of DUPIC bundle with an existing CANDU-6 was presented in a CHF point of view
Study on Unigraphics Drawing Modeling Method for 37-Element and CANFLEX Fuel Bundle
Energy Technology Data Exchange (ETDEWEB)
Jeon, Yu Mi; Park, Joo Hwan
2010-03-15
The CANFLEX bundle contains 43 elements of two different diameters. It has two rings of small diameter elements on the outside, and eight elements (with diameter slightly larger than those in the standard 37-Element bundle) in the center. This larger number of small diameter elements on the outside of the CANFLEX bundle enhances thermo-hydraulic capability, resulting in a higher power capability and an improvement in operating safety margins. As a Result of advanced fuel design for CANFLEX fuel bundles, components consisting of fuel bundles are more complicated. Hence, the detailed modeling of components is inevitable in order to analyze the fuel performance by computational fluid dynamics. In this report, the basic design of the advanced fuel for CANDU reactors was carried out and the methodology for the modeling of fuel bundle were described. Firstly, the components consisting of fuel bundles were separately modeled and saved with different file names. The final feature of fuel bundle was accomplished by an assembling process of components. Since this report developed the modeling methodology based on the Unigraphics program, the basic explanations for the software were given first, and the complete modeling of 37-elements and CANFLEX fuel bundles were provided. The components of CANFLEX fuel bundles were also compared with that of 37-elements fuel bundles. Although, in this report, the modeling methodology is applied only to 37-elements and CANFLEX fuel bundles, this methodology may be applicable to the newly designed fuel bundles which are to be developed in the future
Coupling Systems of Five CARA Fuel Bundles for Atucha I
International Nuclear Information System (INIS)
This paper describe the mechanical design of two options for the coupling systems of five CARA fuel bundles, to be used in the Atucha I nuclear power plant. These systems will be hydraulic tested in a low pressure loop to know their hydraulic loss of pressure
Bohr--Sommerfeld Lagrangians of moduli spaces of Higgs bundles
DEFF Research Database (Denmark)
Biswas, Indranil; Gammelgaard, Niels Leth; Logares, Marina
Let $X$ be a compact connected Riemann surface of genus at least two. Let $M_H(r,d)$ denote the moduli space of semistable Higgs bundles on $X$ of rank $r$ and degree $d$. We prove that the compact complex Bohr-Sommerfeld Lagrangians of $M_H(r,d)$ are precisely the irreducible components of the n...
Regularity for The CR Vector Bundle Problem I
Gong, Xianghong; Webster, S. M.
2009-01-01
We give a new solution to the local integrability problem for CR vector bundles over strictly pseudoconvex real hypersurfaces of dimension seven or greater. It is based on a KAM rapid convergence argument and avoids the previous more difficult Nash-Moser methods. The solution is sharp as to H\\"older continuity.
Self-adjointness of the Gaffney Laplacian on Vector Bundles
International Nuclear Information System (INIS)
We study the Gaffney Laplacian on a vector bundle equipped with a compatible metric and connection over a Riemannian manifold that is possibly geodesically incomplete. Under the hypothesis that the Cauchy boundary is polar, we demonstrate the self-adjointness of this Laplacian. Furthermore, we show that negligible boundary is a necessary and sufficient condition for the self-adjointness of this operator
Elliptic open books on torus bundles over the circle
Etgü, Tolga
2006-01-01
As an application of the construction of open books on plumbed 3-manifolds, we construct elliptic open books on torus bundles over the circle. In certain cases these open books are compatible with Stein fillable contact structures and have minimal genus.
Euler-Lagrange Forms and Cohomology Groups on Jet Bundles
Institute of Scientific and Technical Information of China (English)
CHEN Jing-Bo
2005-01-01
@@ Using the language of jet bundles, we generalize the definitions of Euler-Lagrange one-form and the associated cohomology which were introduced by Guo et al. [Commun. Theor. Phys. 37(2002)1]. Continuous and discreteLagrange mechanics and field theory are presented. Higher order Euler-Lagrange cohomology groups are also introduced.
A Method of Assembling Compact Coherent Fiber-Optic Bundles
Martin, Stefan; Liu, Duncan; Levine, Bruce Martin; Shao, Michael; Wallace, James
2007-01-01
A method of assembling coherent fiber-optic bundles in which all the fibers are packed together as closely as possible is undergoing development. The method is based, straightforwardly, on the established concept of hexagonal close packing; hence, the development efforts are focused on fixtures and techniques for practical implementation of hexagonal close packing of parallel optical fibers.
Signal Integrity Analysis in Single and Bundled Carbon Nanotube Interconnects
International Nuclear Information System (INIS)
Carbon nanotube (CN T) can be considered as an emerging interconnect material in current nano scale regime. They are more promising than other interconnect materials such as Al or Cu because of their robustness to electromigration. This research paper aims to address the crosstalk-related issues (signal integrity) in interconnect lines. Different analytical models of single- (SWCNT), double- (DWCNT), and multiwalled CNTs (MWCNT) are studied to analyze the crosstalk delay at global interconnect lengths. A capacitively coupled three-line bus architecture employing CMOS driver is used for accurate estimation of crosstalk delay. Each line in bus architecture is represented with the equivalent RLC models of single and bundled SWCNT, DWCNT, and MWCNT interconnects. Crosstalk delay is observed at middle line (victim) when it switches in opposite direction with respect to the other two lines (aggressors). Using the data predicted by ITRS 2012, a comparative analysis on the basis of crosstalk delay is performed for bundled SWCNT/DWCNT and single MWCNT interconnects. It is observed that the overall crosstalk delay is improved by 40.92% and 21.37% for single MWCNT in comparison to bundled SWCNT and bundled DWCNT interconnects, respectively.
Moduli of Parabolic Higgs Bundles and Atiyah Algebroids
DEFF Research Database (Denmark)
Logares, Marina; Martens, Johan
2010-01-01
. By considering the case of full flags, we get a Grothendieck–Springer resolution for all other flag types, in particular for the moduli spaces of twisted Higgs bundles, as studied by Markman and Bottacin and used in the recent work of Laumon–Ngô. We discuss the Hitchin system, and demonstrate that...
Heat transfer and fluid friction in bundles of twisted tubes
Dzyubenko, B. V.; Dreitser, G. A.
1986-06-01
The results of heat-transfer and friction studies in bundles of twisted tubes and rods with spiral wire-wrap spacers are analyzed, and recommendations are given for calculating the heat-transfer coefficient in heat exchangers using twisted tubes.
AdS 3-manifolds and Higgs bundles
DEFF Research Database (Denmark)
Alessandrini, Daniele; Li, Qiongling
2015-01-01
In this paper we investigate the relationships between closed AdS 3-manifolds and Higgs bundles. We have a new way to construct AdS structures that allows us to see many of their properties explicitly, for example we can recover the very recent formula by Tholozan for the volumes. We also find...
Dendritic bundles, minicolumns, columns, and cortical output units
Directory of Open Access Journals (Sweden)
Giorgio Innocenti
2010-03-01
Full Text Available The search for the fundamental building block of the cerebral cortex has highlighted three structures, perpendicular to the cortical surface: i columns of neurons with radially invariant response properties, e.g., receptive field position, sensory modality, stimulus orientation or direction, frequency tuning etc. ii minicolumns of radially aligned cell bodies and iii bundles, constituted by the apical dendrites of pyramidal neurons with cell bodies in different layers. The latter were described in detail, and sometimes quantitatively, in several species and areas. It was recently suggested that the dendritic bundles consist of apical dendrites belonging to neurons projecting their axons to specific targets. We review the concept above and suggest that another structural and computational unit of cerebral cortex is the cortical output unit (COU, i.e. an assembly of bundles of apical dendrites and their parent cell bodies including each of the outputs to distant cortical or subcortical structures, of a given cortical locus (area or part of an area. This somato-dendritic assembly receives inputs some of which are common to the whole assembly and determine its radially invariant response properties, others are specific to one or more dendritic bundles, and determine the specific response signature of neurons in the different cortical layers and projecting to different targets.
On Liftings of Local Torus Actions to Fiber Bundles
Yoshida, Takahiko
2007-01-01
In this note we define a lifting of a local torus action modeled on the standard representation (we call it a local torus action for simplicity) to a principal torus bundle, and show that there is an obstruction class for the existence of liftings in the first cohomology of the fundamental group of the orbit space with coefficients in a certain module.
Quantum nonsymmetric gravity and the superfiber bundle formalism
International Nuclear Information System (INIS)
The formalism of the principal super fiber-bundle is applied to quantum Nonsymmetric gravitational theory. It is shown that the metric and Fadeev-Popov fields arise as superfield components of the super connection. Moreover the BRST and anti-BRST transformations are shown to be the gauge transformations of the parameters of the ghost and anti-ghost superfields. (authors)
Quantum Nonsymmetric Gravity and The Superfiber Bundle Formalism
Mebarki, N
1999-01-01
The formalism of the principal superfiber-bundle is applied to quantum Nonsymmetric gravitationl theory. It is shown that the metric and Faddev-Popov fields arise as superfields components of the superconnection. Moreover,the BRST and anti-BRST transformations are shown to be the gauge transformations of parameters the ghost and anti-ghost superfields.
Self-adjointness of the Gaffney Laplacian on Vector Bundles
Energy Technology Data Exchange (ETDEWEB)
Bandara, Lashi, E-mail: lashi.bandara@chalmers.se [Chalmers University of Technology and University of Gothenburg, Mathematical Sciences (Sweden); Milatovic, Ognjen, E-mail: omilatov@unf.edu [University of North Florida, Department of Mathematics and Statistics (United States)
2015-12-15
We study the Gaffney Laplacian on a vector bundle equipped with a compatible metric and connection over a Riemannian manifold that is possibly geodesically incomplete. Under the hypothesis that the Cauchy boundary is polar, we demonstrate the self-adjointness of this Laplacian. Furthermore, we show that negligible boundary is a necessary and sufficient condition for the self-adjointness of this operator.
A note on stochastic calculus in vector bundles
Catuogno, Pedro J.; Ledesma, Diego S.; Ruffino, Paulo R.
2011-01-01
The aim of these notes is to relate covariant stochastic integration in a vector bundle $E$ (as in Norris \\cite{Norris}) with the usual Stratonovich calculus via the connector $\\K:TE \\rightarrow E$ (cf. e.g. Paterson \\cite{Paterson} or Poor \\cite{Poor}) which carries the connection dependence.
Vibrations of turbine blades bundles model with rubber damping elements
Czech Academy of Sciences Publication Activity Database
Půst, Ladislav; Pešek, Luděk
2014-01-01
Roč. 21, č. 1 (2014), s. 45-52. ISSN 1802-1484 R&D Projects: GA ČR GA101/09/1166 Institutional support: RVO:61388998 Keywords : mathematical model * bundle of five blades * rubber damping elements * eigenmodes Subject RIV: BI - Acoustics http://www.engineeringmechanics.cz/obsahy.html?R=21&C=1
Multicell slug flow heat transfer analysis of finite LMFBR bundles
Energy Technology Data Exchange (ETDEWEB)
Yeung, M.K.; Wolf, L.
1978-12-01
An analytical two-dimensional, multi-region, multi-cell technique has been developed for the thermal analysis of LMFBR rod bundles. Local temperature fields of various unit cells were obtained for 7, 19, and 37-rod bundles of different geometries and power distributions. The validity of the technique has been verified by its excellent agreement with the THTB calculational result. By comparing the calculated fully-developed circumferential clad temperature distribution with those of the experimental measurements, an axial correction factor has been derived to account for the entrance effect for practical considerations. Moreover, the knowledge of the local temperature field of the rod bundle leads to the determination of the effective mixing lengths L/sub ij/ for adjacent subchannels of various geometries. It was shown that the implementation of the accurately determined L/sub ij/ into COBRA-IIIC calculations has fairly significant effects on intersubchannel mixing. In addition, a scheme has been proposed to couple the 2-D distributed and lumped parameter calculation by COBRA-IIIC such that the entrance effect can be implanted into the distributed parameter analysis. The technique has demonstrated its applicability for a 7-rod bundle and the results of calculation were compared to those of three-dimensional analyses and experimental measurements.
The fiber bundle formalism for the quantization in curved spaces
International Nuclear Information System (INIS)
We set up a geometrical formulation of the canonical quantization of free Klein-Gordon field on a gravitational background. We introduce the notion of the Bogolubov bundle as the principal fiber bundle over the space of all Cauchy surfaces belonging to some fixed foliation of space-time, with the Bogolubov group as the structure group, as a tool in considering local Bogolubov transformations. Sections of the associated complex structure bundle have the meaning of attaching Hilbert spaces to Cauchy surfaces. We single out, as physical, sections defined by the equation of parallel transport on the Bogolubov bundle. The connection is then subjected to a certain nonlinear differential equation. We find a particular solution, which happens to coincide with a formula given by L.Parker for Robertson-Walker space-times. Finally, we adopt the adiabatic hypothesis as the physical input to the formalism and fix in this way a free parameter in the connection. Concluding, we comment on a possible geometrical interpretation of the regularization of stress-energy tensor and on generalizations of the formalism toward quantum gravity. 14 refs. (Author)
Product Bundling and Shared Information Goods: A Pricing Exercise
Morrison, William G.
2016-01-01
In this article, the author describes an exercise in which two pricing problems (product bundling and the sharing of digital information goods) can be understood using the same analytical approach. The exercise allows students to calculate the correct numerical answers with relative ease, while the teaching plan demonstrates the importance of the…
MYOCARDIAL DEFORMATION AND COMPLETE LEFT BUNDLE BRANCH BLOCK
Directory of Open Access Journals (Sweden)
E. N. Pavlyukova
2015-12-01
Full Text Available Tissue Doppler imaging is evolving as a useful echocardiographic tool for quantitative assessment of left ventricular systolic and diastolic function. Over the last 10 years, myocardial deformation imaging has become possible initially with tissue Doppler , and more recently with myocardial speckle-tracking using 2D echocardiography. Unlike simple tissue velocity measurements, deformation measurements are specific for the region of interest. Strain rate or strain measurements have been used as sensitive indicators for subclinical diseases, and it is the most widely used tool to assess mechanical dyssynchrony. Left bundle branch block is a frequent, etiologically heterogeneous, clinically hostile and diagnostically challenging entity. About 2% of patients underwent cardiac stress testing show stable or intermittent left bundle branch block. Presence of left bundle branch block is associated with a lower and slower diastolic coronary flow velocity especially during hyperemia. Stress echocardiography is the best option for the diagnosis of ischemic heart disease, albeit specificity and sensitivity reduce in patients with left bundle branch block in the territory of left anterior descending artery in presence of initial septum dyskinesia.
Rigidity of Minimal Submanifolds with Flat Normal Bundle
Indian Academy of Sciences (India)
Hai-Ping Fu
2010-09-01
Let $M^n(n≥ 3)$ be an -dimensional complete immersed $\\frac{n-2}{n}$-superstable minimal submanifold in an $(n+p)$-dimensional Euclidean space $\\mathbb{R}^{n+p}$ with flat normal bundle. We prove that if the second fundamental form of satisfies some decay conditions, then is an affine plane or a catenoid in some Euclidean subspace.
Fibre bundles, connections, general relativity, and Einstein-Cartan theory
Socolovsky, Miguel
2011-01-01
We present in the most natural way, that is, in the context of the theory of vector and principal bundles and connections in them, fundamental geometrical concepts related to General Relativity and one of its extensions, the Einstein-Cartan theory.
Cohomology of line bundles: Proof of the algorithm
International Nuclear Information System (INIS)
We present a proof of the algorithm for computing line bundle valued cohomology classes over toric varieties conjectured by Blumenhagen et al. [e-print arXiv:cond-mat/1003.5217] and suggest a kind of Serre duality for combinatorial Betti numbers that we observed when computing examples.
Assembly and operation experience of EVA II steam reforming bundle
International Nuclear Information System (INIS)
The main test component of the experimental facility EVA-II/ADAM-II is a helium heated steam reformer bundle with 30 tubes. The tubes are filled with a catalyst of raschig ring type. The main test of the component were related to the power dependence. A series of experiment dealt with the influence of steam/methane ratio on the carbon deposit formation
A comprehensive comparison on vibration and heat transfer of two elastic heat transfer tube bundles
Institute of Scientific and Technical Information of China (English)
闫柯; 葛培琪; 翟强
2015-01-01
Elastic heat transfer tube bundles are widely used in the field of flow-induced vibration heat transfer enhancement. Two types of mainly used tube bundles, the planar elastic tube bundle and the conical spiral tube bundle were comprehensively compared in the condition of the same shell side diameter. The natural mode characteristics, the effect of fluid−structure interaction, the stress distribution, the comprehensive heat transfer performance and the secondary fluid flow of the two elastic tube bundles were all concluded and compared. The results show that the natural frequency and the critical velocity of vibration buckling of the planar elastic tube bundle are larger than those of the conical spiral tube bundle, while the stress distribution and the comprehensive heat transfer performance of the conical spiral tube bundle are relatively better.
2010-02-24
... Price Index Adjustments for Expenditure Limitations and Lobbyist Bundling Disclosure Threshold AGENCY: Federal Election Commission. ACTION: Notice of adjustments to expenditure limitations and lobbyist... Commission'') is adjusting certain expenditure limitations and the lobbyist bundling disclosure threshold...
2012-02-21
... Price Index Adjustments for Expenditure Limitations and Lobbyist Bundling Disclosure Threshold AGENCY: Federal Election Commission. ACTION: Notice of adjustments to expenditure limitations and lobbyist... Commission'') is adjusting certain expenditure limitations and the lobbyist bundling disclosure threshold...
Wagih, Ahmad M.
2013-01-01
A careful review of the literature suggests that a significant number of patients undergoing anterior cruciate ligament (ACL) reconstruction have less-than-optimal results. Although overall outcomes of ACL reconstruction are favorable, there remains considerable room for improvement. Anatomically, the ACL consists of 2 major functional bundles, the anteromedial bundle and the posterolateral bundle. Biomechanically, both bundles contribute significantly to the anterior and rotational stability...
Equilibrium Bundle Size of Rodlike Polyelectrolytes with Counterion-Induced Attractive Interactions
Henle, Mark L.; Pincus, Philip A.
2004-01-01
Multivalent counterions can induce an effective attraction between like-charged rodlike polyelectrolytes, leading to the formation of polelectrolyte bundles. In this paper, we calculate the equilibrium bundle size using a simple model in which the attraction between polyelectrolytes (assumed to be pairwise additive) is treated phenomenologically. If the counterions are point-like, they almost completely neutralize the charge of the bundle, and the equilibrium bundle size diverges. When the co...
Twisted Partial Actions, A Classification of Stable C*-Algebraic Bundles (Preliminary Version)
Exel, Ruy
1994-01-01
We introduce the notion of continuous twisted partial actions of a locally compact group on a C*-algebra. With such, we construct an associated C*-algebraic bundle called the semidirect product bundle. Our main theorem shows that, given any C*-algebraic bundle which is second countable and whose unit fiber algebra is stable, there is a continuous twisted partial action of the base group on the unit fiber algebra, whose associated semidirect product bundle is isomorphic to the given one.
Why Bundle Discounts Can Be a Profitable Alternative to Competing on Price Promotions
Subramanian Balachander; Bikram Ghosh; Axel Stock
2010-01-01
Price promotions and bundling have been two of the most widely used marketing tools in industry practice. Past literature has assumed that firms respond to price promotions by promoting a product in the same category. In this paper, we extend this literature as well as the bundling literature by considering the possibility that a firm may respond to a competitor's price promotions by also offering a cross-buying or bundling discount. Using a game-theoretic model, we show that bundle discounts...
An extension theorem of Ohsawa-Takegoshi type for sections of a vector bundle
Raufi, Hossein
2014-01-01
Using $L^2$-methods for the $\\bar\\partial$-equation we prove that the Ohsawa-Takegoshi extension theorem also holds for holomorphic sections of a vector bundle, over compact K\\"ahler manifolds. We then proceed to show that the conditions that are needed are more liberal than the ones one would need if one instead reduced the extension problem to line bundles through the usual algebraic geometric procedure of studying the projective bundle associated with the vector bundle.
On hyperbolicity of SU(2)-equivariant, punctured disc bundles over the complex affine quadric
Iannuzzi, Andrea
2011-01-01
Given a holomorphic line bundle over the complex affine quadric $Q^2$, we investigate its Stein, SU(2)-equivariant disc bundles. Up to equivariant biholomorphism, these are all contained in a maximal one, say $\\Omega_{max}$. By removing the zero section to $\\Omega_{max}$ one obtains the unique Stein, SU(2)-equivariant, punctured disc bundle over $Q^2$ which contains entire curves. All other such punctured disc bundles are shown to be Kobayashi hyperbolic.
Compressive force generation by a bundle of living biofilaments
Ramachandran, Sanoop; Ryckaert, Jean-Paul
2013-08-01
To study the compressional forces exerted by a bundle of living stiff filaments pressing on a surface, akin to the case of an actin bundle in filopodia structures, we have performed particulate molecular dynamics simulations of a grafted bundle of parallel living (self-assembling) filaments, in chemical equilibrium with a solution of their constitutive monomers. Equilibrium is established as these filaments, grafted at one end to a wall of the simulation box, grow at their chemically active free end, and encounter the opposite confining wall of the simulation box. Further growth of filaments requires bending and thus energy, which automatically limit the populations of longer filaments. The resulting filament sizes distribution and the force exerted by the bundle on the obstacle are analyzed for different grafting densities and different sub- or supercritical conditions, these properties being compared with the predictions of the corresponding ideal confined bundle model. In this analysis, non-ideal effects due to interactions between filaments and confinement effects are singled out. For all state points considered at the same temperature and at the same gap width between the two surfaces, the force per filament exerted on the opposite wall appears to be a function of a rescaled free monomer density hat{ρ }_1^eff. This quantity can be estimated directly from the characteristic length of the exponential filament size distribution P observed in the size domain where these grafted filaments are not in direct contact with the wall. We also analyze the dynamics of the filament contour length fluctuations in terms of effective polymerization (U) and depolymerization (W) rates, where again it is possible to disentangle non-ideal and confinement effects.
An evaluation on the cutting technologies for decommissioning of the tube bundles in the RPV of NPPs
International Nuclear Information System (INIS)
Highlights: • This paper is to evaluate an optimal cutting technology of the tube bundles in the RPV of NPPs. • Characteristics of the tube bundles were analyzed and alternative cutting technologies of the tube bundles were evaluated. • An optimal cutting technology of the tube bundles was suggested. - Abstract: This paper is to evaluate an optimal cutting technology of the tube bundles in the reactor pressure vessel of nuclear power plants. Characteristics of the tube bundles were analyzed and alternative cutting technologies of the tube bundles were evaluated. The optimal cutting technology of the tube bundles was suggested
On the Topology of Real Bundle Pairs over Nodal Symmetric Surfaces
Georgieva, Penka
2015-01-01
We give an alternative argument for the classification of real bundle pairs over smooth symmetric surfaces and extend this classification to nodal symmetric surfaces. We also classify the homotopy classes of automorphisms of real bundle pairs over symmetric surfaces. The two statements together describe the isomorphisms between real bundle pairs over symmetric surfaces up to deformation.
Fuel bundle loss of cooling inside the fuelling machine at CANDU6 PHWR
International Nuclear Information System (INIS)
This article describes the that loss of forced circulation cooling flow of induce spent fuel bundle loss of cooling and fission product releasing, analyzes the effect of reactor building and environment due to the fuel bundle rupturing, discusses the countermeasure to deal with the event of loss of cooling of spent fuel bundle. (authors)
Standardization of Type 2 Diabetes Outpatient Expenditure with Bundled Payment Method in China
Directory of Open Access Journals (Sweden)
Guo-Chao Xu
2016-01-01
Conclusions: We argued that it is feasible to implement bundled payment on type 2 diabetes outpatient services. Bundled payment is effective to control the increase of outpatient expenditure. Further improvements are needed for the implementation of bundled payment reimbursement standards, together with relevant policies and measures.
Semistability of Certain Bundles on Second Symmetric Power of a Curve
Dan, Krishanu; Pal, Sarbeswar
2015-01-01
Let $C$ be a smooth irreducible projective curve and $E$ be a rank 2 stable vector bundle on $C$. Then one can associate a rank 4 vector bundle $\\mathcal{F}_2(E)$ on $S^2(C)$, second symmetric power of $C$. Our goal in this article is to study semistability of this bundle.
Penurunan Kerugian Head pada Belokan Pipa dengan Peletakan Tube Bundle
Directory of Open Access Journals (Sweden)
Pratikto
2010-01-01
Full Text Available Fluid flow flowing through an elbow causes separation. Separation leads to vortex, shake and cavity. As a result, the head loss will increase and the pipe installation is potentially damaged. Thus, separation must be eliminated. The separation is identified by the presence of high pressure decreasing in the downstream of elbow. To minimize the pressure decreasing in elbow, we need flow conditioner like a tube bundle. The aim of this research is to identify the influence of tube bundle placement toward the head loss such as pressure drop. The elbow being tested is placed on a pipe installation already equipped by testing aids such as computers and its software, pressure transmitter, and rotameter. The free variable in this study is the distance of the tube bundle from the outlet edge of the pipe turn 2D, 3D, 4D and 5D and fluid flow volume which flows through the installation that are 1000, 1100, 1200, 1300, 1400, 1500, 1600, 1700, 1800, 1900 and 2000 litres/hour. Whereas, the dependent variable is the pressure drop (p measured by pressure transmitter and the head loss of which the value is obtained from the measurement of pressure drop. The test was conducted on 1.25 inch in diameter elbow with 22 holes of tube bundle and 27 mm in length. To know the head loss, so the pressure drop (p of fluid at upstream and downstream of the pipe turn are measured using 2 pressure transmitters connected to the computer through ADC (Analog Digital Converter. The data had already recorded in computer was processed using the LabView software to get the averaged value of the pressure drop. Abstract in Bahasa Indonesia: Aliran Fluida yang mengalir melalui belokan pipa menyebabkan terjadinya separasi. Separasi mengakibatkan terjadinya vortex, getaran, dan kavitasi, dimana kerugian tersebut mengakibatkan kerugian head meningkat dan berpotensi merusak instalasi pipa sehingga separasi perlu dihilangkan. Separasi ini ditandai dengan penurunan tekanan yang besar
Radical power profile effect of DUPIC bundle on critical heat flux
International Nuclear Information System (INIS)
The axial and ring power profiles of DUPIC bundle are much different from those of reference 37-element fuel bundle since a DUPIC fuel bundle is -re-fabricated under proliferation resistance using spent PWR fuel and 2-bundle shift refuelling scheme of DUPIC bundle is proposed to CANDU-6 reactor. In case that the ring power porfile of a fuel bundle is altered, the flow and enthalpy distribution of subchannels and the radial position of CHF occurrence will be changed. Similarly, the axial power profile of a fuel channel affects CHF, axial position of CHF occurrence, axial enthalpy, quality and pressure distribution. The ring power profile of the DUPIC bundle as increasing burnup is much altered and flattened at high burnup, compared to 37-element bundle. It caused that one fuel bundle has a different ring power profile from the other fuel bundles at the different axial positions even in the same fuel channel. Therefore, how to consider burnup or ring power effect on CHF is very important to DUPIC thermalhydraulic analysis. At present study, thermalhydraulic analysis of a DUPIC bundles was performed in order to evaluate the ring power profile effect on CHF. The subchannel enthalpy, mass flux and CHF distribution from 0 burnup to discharged burnup (18,000 MWd/tHM) of DUPIC bundle were evaluated using ASSERT-PV subchannel code. The results of DUPIC bundles were compared to those of 37-elemental bundle and the comparability of DUPIC bundle with an existing CANDU-6 was presented in a CHF point of view
Separation and re-adhesion processes of two adhered single-walled carbon nanotube bundles
International Nuclear Information System (INIS)
Carbon nanotubes are desirable components of nanoelectromechanical (NEM) devices due to their excellent mechanical and electrical properties. In this study, dielectrophoresis, a potential high-rate nanomanufacturing process, was used to assemble single-walled carbon nanotube (SWCNT) bundles suspended over a trench. The intent was to assemble a single SWCNT bundle between two electrodes. However, it was observed that when two or more SWCNT bundles assembled across the trench, the bundles were attached together in a portion of the suspended section. This study models the separation and re-adhesion processes of two adhered SWCNT bundles as their internal tensions are varied using an atomic force microscope (AFM) tip. Two devices were selected with distinct SWCNT bundles. Observation of the force–distance measurements through applying an AFM tip at the middle of the suspended SWCNT bundles, in conjunction with continuum mechanics modelling, allowed the work of adhesion between the two nanotube bundles to be determined. As the force was applied by the AFM tip, the tension induced in each bundle increases sufficiently to partially overcome the adhesion between the bundles, thereby decreasing the adhesive length. The adhesive length then recovers due to the decrease in the induced tension during the unloading process. The average value of the work of adhesion between two adhered SWCNT bundles was determined to be 0.37 J m−2 according to the experimental data and modelling results. (paper)
Linear duals of graded bundles and higher analogues of (Lie) algebroids
Bruce, Andrew James; Grabowska, Katarzyna; Grabowski, Janusz
2016-03-01
Graded bundles are a class of graded manifolds which represent a natural generalisation of vector bundles and include the higher order tangent bundles as canonical examples. We present and study the concept of the linearisation of graded bundle which allows us to define the notion of the linear dual of a graded bundle. They are examples of double structures, graded-linear (GL) bundles, including double vector bundles as a particular case. On GL-bundles we define what we shall call weighted algebroids, which are to be understood as algebroids in the category of graded bundles. They can be considered as a geometrical framework for higher order Lagrangian mechanics. Canonical examples are reductions of higher tangent bundles of Lie groupoids. Weighted algebroids represent also a generalisation of VB-algebroids as defined by Gracia-Saz & Mehta and the LA-bundles of Mackenzie. The resulting structures are strikingly similar to Voronov's higher Lie algebroids, however our approach does not require the initial structures to be defined on supermanifolds.
Frobenius Pull Backs of Vector Bundles in Higher Dimensions
Indian Academy of Sciences (India)
V Trivedi
2012-11-01
We prove that for a smooth projective variety of arbitrary dimension and for a vector bundle over , the Harder–Narasimhan filtration of a Frobenius pull back of is a refinement of the Frobenius pull back of the Harder–Narasimhan filtration of , provided there is a lower bound on the characteristic (in terms of rank of and the slope of the destabilizing sheaf of the cotangent bundle of ). We also recall some examples, due to Raynaud and Monsky, to show that some lower bound on is necessary. We also give a bound on the instability degree of the Frobenius pull back of in terms of the instability degree of and well defined invariants of .
Seismic analysis and test of model steam generator tube bundle
International Nuclear Information System (INIS)
The seismic response analysis and experimental study of a model PWR steam generator tube bundle has been completed. A planar tube mathematical model of linear FEM (finite element method) and simplified model tube bundle on the scale of 1:4.4 are used in the study. White noise sweep test shows that the effect of clearance and contact constraint between tube and anti-vibration bar is insignificant, the global fundamental frequency component is absolutely dominant, and the higher frequency components only affect the local vibration in different locations. The experimental results indicate that fundamental frequency component is dominant in seismic acceleration response spectrum. The second, third and fourth frequency components appear in the kind of frequency bands. The experimental data are in good agreement with the linear FEM results. The effectiveness of simplified mathematical model is verified
An improved partial bundle method for linearly constrained minimax problems
Directory of Open Access Journals (Sweden)
Chunming Tang
2016-02-01
Full Text Available In this paper, we propose an improved partial bundle method for solving linearly constrained minimax problems. In order to reduce the number of component function evaluations, we utilize a partial cutting-planes model to substitute for the traditional one. At each iteration, only one quadratic programming subproblem needs to be solved to obtain a new trial point. An improved descent test criterion is introduced to simplify the algorithm. The method produces a sequence of feasible trial points, and ensures that the objective function is monotonically decreasing on the sequence of stability centers. Global convergence of the algorithm is established. Moreover, we utilize the subgradient aggregation strategy to control the size of the bundle and therefore overcome the difficulty of computation and storage. Finally, some preliminary numerical results show that the proposed method is effective.
Dimer model for Tau proteins bound in microtubule bundles
Hall, Natalie; Kluber, Alexander; Hayre, N. Robert; Singh, Rajiv; Cox, Daniel
2013-03-01
The microtubule associated protein tau is important in nucleating and maintaining microtubule spacing and structure in neuronal axons. Modification of tau is implicated as a later stage process in Alzheimer's disease, but little is known about the structure of tau in microtubule bundles. We present preliminary work on a proposed model for tau dimers in microtubule bundles (dimers are the minimal units since there is one microtubule binding domain per tau). First, a model of tau monomer was created and its characteristics explored using implicit solvent molecular dynamics simulation. Multiple simulations yield a partially collapsed form with separate positively/negatively charged clumps, but which are a factor of two smaller than required by observed microtubule spacing. We argue that this will elongate in dimer form to lower electrostatic energy at a cost of entropic ``spring'' energy. We will present preliminary results on steered molecular dynamics runs on tau dimers to estimate the actual force constant. Supported by US NSF Grant DMR 1207624.
Balanced metrics for vector bundles and polarised manifolds
DEFF Research Database (Denmark)
Garcia Fernandez, Mario; Ross, Julius
2012-01-01
We consider a notion of balanced metrics for triples (X, L, E) which depend on a parameter α, where X is smooth complex manifold with an ample line bundle L and E is a holomorphic vector bundle over X. For generic choice of α, we prove that the limit of a convergent sequence of balanced metrics...... leads to a Hermitian-Einstein metric on E and a constant scalar curvature Kähler metric in c_1(L). For special values of α, limits of balanced metrics are solutions of a system of coupled equations relating a Hermitian-Einstein metric on E and a Kähler metric in c1(L). For this, we compute the top two...
Nuclear spin relaxation due to random motion of vortex bundles
International Nuclear Information System (INIS)
The dependence of nuclear-spin-relaxation rate T1 on NMR resonant frequency for a layered superconducting sample has been analyzed theoretically. In the considered arrangement the Zeeman field has been applied in the plane of superconducting layers while the relaxation was due to interactions between the spin systems and moving flux bundles, created by the transport current flowing along superconducting layers. It has been found that the functional form of a dependence of spin-relaxation rate on the Zeeman field has two components, a Lorentzian and an oscillatory one. The characteristic rolloff frequency of the Lorentzian component depends on the pinning properties of the sample. The period of oscillations of the oscillatory component is of the order of the inverse of interaction time of flowing flux bundles with a probe nucleus. copyright 1996 The American Physical Society
Attribute-based edge bundling for visualizing social networks
Guo, Lin; Zuo, Wanli; Peng, Tao; Adhikari, Binod Kumar
2015-11-01
Most nodes in complex networks have multiple attributes, which make them hard to analyze. Because general edge bundling algorithms fail to handle complex networks as a result of their intricate features, network simplification is extremely important. This paper proposes an attribute-based edge bundling algorithm that displays similar edges in nearby locations. Meanwhile, by analyzing complex networks at a community level, the overlapping clustering of nodes is well implemented, and better clustering effects can be achieved by grouping similar edges together. On the basis of datasets with different types and sizes, the experiments illustrate the simplification degree of the intricate graphs created by the algorithm proposed, which outperforms established competitors in correctness and effectiveness.
Infinitesimal moduli of G2 holonomy manifolds with instanton bundles
de la Ossa, Xenia; Svanes, Eirik Eik
2016-01-01
We describe the infinitesimal moduli space of pairs $(Y, V)$ where $Y$ is a manifold with $G_2$ holonomy, and $V$ is a vector bundle on $Y$ with an instanton connection. These structures arise in connection to the moduli space of heterotic string compactifications on compact and non-compact seven dimensional spaces, e.g. domain walls. Employing the canonical $G_2$ cohomology $H^*_{{\\check{\\rm d}}_E}(Y,E)$ developed by Reyes-Carri\\'on and Fern\\'andez and Ugarte, we show that the moduli space decomposes into the sum of the bundle moduli $H^1_{{\\check{\\rm d}}_A}(Y,{\\rm End}(V))$ plus the moduli of the $G_2$ structure preserving the instanton condition. The latter piece is contained in $H^1_{{\\check{\\rm d}}_\
Persistence Length and Nanomechanics of Random Bundles of Nanotubes
Energy Technology Data Exchange (ETDEWEB)
Yakobson, Boris I. [Rice University, Department of Mechanical Engineering and Materials Science, Department of Chemistry, and Center for Nanoscale Science and Technology (United States)], E-mail: biy@rice.edu; Couchman, Luise S. [Naval Research Laboratory, Code 7130 (United States)
2006-02-15
A connection between the stiffness of carbon nanotubes (CNT) and their mesoscopic physical behaviour is presented. Persistence lengths of CNT and bundles are calculated and shown to be in macroscopic range (0.03-1 mm for an individual tube), exceeding by many orders of magnitude the typical diameters (around 1-3 nm). Consequently, thermal fluctuations can be neglected when scaling analysis is applied to randomly packed (as produced) CNT network, leading to an approximate equation of state for such material. Beyond the linear elasticity, the outmost CNT are shown to gradually split from the bent bundles; this permits access of solvent or reacting species to the CNT walls, an important mechanism promoting solubilization and chemical functionalization of nanotubes.
Multiplexed holographic memory by use of fiber bundle referencing
Zhang, Jiasen; Aruga, Tadashi
2005-04-01
We propose a volume holographic storage technique, in which a fiber bundle is used to guide the reference beam. Multiplexing is implemented by changing the incident direction of the laser beam upon the fiber bundle in the reference arm. In the technique, we make the system more compact by using a wedge prism to change the direction of the laser beam. This method has a large accessible angular scanning range and a large geometric storage bandwidth. Multiple images are stored in a LiNbO3:Fe crystal with an angular separation of 0.05° between successive holograms using a wedge prism with a deviation angle of 8°. This method is useful as a new image storage technique because of its compactness and simplicity.
CFD analysis of flow field in a triangular rod bundle
International Nuclear Information System (INIS)
The flow field was investigated in subchannels of VVER-440 pressurized water cooled reactors' fuel assemblies (triangular lattice, P/D = 1.35). Impacts of the mesh resolution and turbulence model were studied in order to obtain guidelines for CFD calculations of VVER-440 rod bundles. Results were compared to measurement data published by Trupp and Azad in 1975. The study pointed out that RANS method with BSL Reynolds stress model using a sufficient fine grid can provide an accurate prediction for the turbulence quantities in this lattice. Applying the experiences of the sensitivity study thermal hydraulic processes were investigated in VVER-440 rod bundle sections. Based on the examinations the spacer grids have important effects on the cross flows, axial velocity and outlet temperature distribution of subchannels therefore they have to be modeled satisfactorily in CFD calculations.
Quantum Turbulence: Vortex Bundle Collapse and Kolmogorov Spectrum
Nemirovskii, Sergey K.
2015-12-01
The statement of problem is motivated by the idea of modeling the classical turbulence with a set of chaotic quantized vortex filaments in superfluids. Among various arguments supporting the idea of quasi-classic behavior of quantum turbulence, the strongest, probably, is the k dependence of the spectra of energy, E(k)∝ k^{-5/3} obtained in numerical simulations and experiments. At the same time, the mechanism of classical vs. quantum turbulence is not clarified and the source of the k^{-5/3} dependence is unclear. In this work, we concentrated on the nonuniform vortex bundles. This choice is related to the actively discussed question concerning a role of collapses in the vortex dynamics in formation of turbulent spectra. We demonstrate that the nonuniform vortex bundles, which appear in result of nonlinear vortex dynamics, generates an energy spectrum which is close to the Kolmogorov dependence ∝ k^{-5/3}.
CAT reconstruction and potting comparison of a LMFBR fuel bundle
International Nuclear Information System (INIS)
A standard Liquid Metal Fast Breeder Reactor (LMFBR) subassembly used in the Experimental Breeder Reactor II (EBR-II) was investigated, by remote techniques, for fuel bundle distortion by both nondestructive and destructive methods, and the results from both methods were compared. The non-destructive method employed neutron tomography to reconstruct the locations of fuel elements through the use of a maximum entropy reconstruction algorithm known as MENT. The destructive method consisted of ''potting'' (a technique that embeds and permanently fixes the fuel elements in a solid matrix) the subassembly, and then cutting and polishing the individual sections. The comparison indicated that the tomography reconstruction provided good results in describing the bundle geometry and spacer-wire locations, with the overall resolution being on the order of a spacer-wire diameter. A dimensional consistency check indicated that the element and spacer-wire dimensions were accurately reproduced in the reconstruction
Cellulosic Fibers: Effect of Processing on Fiber Bundle Strength
DEFF Research Database (Denmark)
Thygesen, Anders; Madsen, Bo; Thomsen, Anne Belinda; Lilholt, Hans
2011-01-01
A range of differently processed cellulosic fibers from flax and hemp plants were investigated to study the relation between processing of cellulosic fibers and fiber bundle strength. The studied processing methods are applied for yarn production and include retting, scutching, carding, and...... cottonization. There was a monotonically decreasing relationship between the strength and the number of processing steps, which was well fitted by an exponential regression line. The reduction factor was determined to be 0.27, indicating that the fiber bundle strength was on average reduced by 27% per...... processing step at the applied conditions. No large changes in cellulose content and crystallinity were observed, so the reduction in strength must be explained by other changes in the fiber ultrastructure. Altogether, the study presents a quantitative basis for reduction in strength of cellulosic fibers due...
On phenomena of turbulent flow through rod bundles
International Nuclear Information System (INIS)
Experimental studies have shown that the axial and azimuthal turbulence intensities in the gap regions of rod bundles increase strongly with decreasing rod spacing; the fluctuating velocities in the axial and azimuthal directions have a quasi-periodic behavior. To determine the origin of this phenomenon and its characteristic as a function of the geometry and the Reynolds number, an experimental investigation was performed on the turbulent flow in several rod bundles with different aspect ratios (P/D, W/D). Hot-wires and microphones were used for the measurements of velocity and wall pressure fluctuations. The data were evaluated to obtain spectra as well as auto and cross correlations. Based on the results, a phenomenological model is proposed to explain this phenomenon. By means of the model, the mass exchange between neighbouring subchannels is explained. (orig.)
Bagger-Witten line bundles on moduli spaces of elliptic curves
Gu, W
2016-01-01
In this paper we discuss Bagger-Witten line bundles over moduli spaces of SCFTs. We review how in general they are `fractional' line bundles, not honest line bundles, twisted on triple overlaps. We discuss the special case of moduli spaces of elliptic curves in detail. There, the Bagger-Witten line bundles does not exist as an ordinary line bundle, but rather is necessarily fractional. As a fractional line bundle, it is nontrivial (though torsion) over the uncompactified moduli stack, and its restriction to the interior, excising corners with enhanced stabilizers, is also fractional. We review and compare to results of recent work arguing that well-definedness of the worldsheet metric implies that the Bagger-Witten line bundle is torsion, and give general arguments on the existence of universal structures on moduli spaces of SCFTs, in which superconformal deformation parameters are promoted to nondynamical fields ranging over the SCFT moduli space.
Investigations on flow induced vibration of simulated CANDU fuel bundles in a pipe
International Nuclear Information System (INIS)
In this paper, vibration of a two-bundle string consisting of simulated CANDU fuel bundles subjected to turbulent liquid flow is investigated through numerical simulations and experiments. Large eddy simulation is used to solve the three-dimensional turbulent flow surrounding the fuel bundles for determining fluid excitations. The CFD model includes pipe flow, flow through the inlet fuel bundle along with its two endplates, half of the second bundle and its upstream endplate. The fluid excitation obtained from the fluid model is subsequently fed into a fuel bundle vibration code written in FORTRAN. Fluid structure interaction terms for the fuel elements are approximated using the slender body theory. Simulation results are compared to measurements conducted on the simulated fuel bundles in a testing hydraulic loop. (author)
The stages of atrioventricular bundle formation in the human embryonic heart
Directory of Open Access Journals (Sweden)
Silkina Yu.V.
2009-01-01
Full Text Available The origin, stages and histogenetic processes in atrioventricular bundle were investigated. We studied the human embryonic heart from 5 to 12 week of development. Antibodies to neurofilaments, Ki-67, MSA, α-SMA and neuregulin were used. Formation of the primordia of the atrioventricular bundle depends on the chamber formation in early heart. The first morphologic reconstruction in the atrioventricular bundle starts from 5 week of gestational age. In this time we studied proximal and distal primordias, which formed general tract at 7 week. The early human heart was characterized by strong connections with atrioventricular fibrous tissue, left and right septal cuspes of mitral and tricuspidal valves. Formation of the atrioventricular bundle branches has two stages: primary and repeated growth. Median fibers are blind-ended. We suppose that atrioventricular bundle and bundle branches have extracardiac origin. Histogenesis of the atrioventricular bundle contin-ues after 12 week of human development.
Anatomic double-bundle anterior cruciate ligament recon-struction
Dai, Xue-Song
2012-01-01
【Abstract】Objective: To retrospectively evaluate the early results of anatomic double-bundle anterior cruci-ate ligament (ACL) reconstruction and compare with the results of native ACL of the contralateral knee. Methods: The results of a consecutive series of 118 patients receiving arthroscopic ACL reconstruction were evaluated. Eight patients were lost to the latest follow-up, leaving a total of 110 patients available for study within at least 3 years’ clinical fol...
Integral Canonical Models for Automorphic Vector Bundles of Abelian Type
Lovering, Tom
2016-01-01
We define and construct integral canonical models for automorphic vector bundles over Shimura varieties of abelian type. More precisely, we first build on Kisin's work to construct integral canonical models over rings of integers of number fields with finitely many primes inverted for Shimura varieties of abelian type with hyperspecial level at all primes we do not invert, compatible with Kisin's construction. We then define a notion of an integral canonical model for the standard principal b...
Apolipophorin III: lipopolysaccharide binding requires helix bundle opening
Leon, Leonardo J.; Idangodage, Hasitha; Wan, Chung-Ping L.; Weers, Paul M.M.
2006-01-01
Apolipophorin III (apoLp-III) is a prototypical apolipoprotein used for structure-function studies. Besides its crucial role in lipid transport, apoLp-III is able to associate with fungal and bacterial membranes and stimulate cellular immune responses. We recently demonstrated binding interaction of apoLp-III of the greater wax moth, Galleria mellonella, with lipopolysaccharides (LPS). In the present study, the requirement of helix bundle opening for LPS binding interaction was investigated. ...
Lateral mechanical coupling of stereocilia in cochlear hair bundles.
Langer, M G; Fink, S.; Koitschev, A; Rexhausen, U; Hörber, J K; Ruppersberg, J P
2001-01-01
For understanding the gating process of transduction channels in the inner ear it is essential to characterize and examine the functional properties of the ultrastructure of stereociliary bundles. There is strong evidence that transduction channels in hair cells are gated by directly pulling at the so-called tip links. In addition to these tip links a second class of filamentous structures was identified in the scanning and transmission electron microscope: the side-to-side links. These links...
Heat transfer in rod bundles with severe clad deformations
International Nuclear Information System (INIS)
The content of the paper is focused on heat transfer conditions during the reflood phase of a LOCA in slightly to severely deformed PWR fuel rod bundle geometries. The status of analytical and, especially, of experimental work is described as far as it is possible within this frame. Emphasis is placed on the presentation of the results of ''Flooding Experiments with Blocked Arrays'' (FEBA), a program performed at the Kernforschungszentrum Karlsruhe in the frame of the Project Nuclear Safety (PNS). (orig./WL)
Universality Class of Fiber Bundle Model on Complex Networks
Kim, Dong-Hee; Kim, Beom Jun; Jeong, Hawoong
2004-01-01
We investigate the failure characteristics of complex networks within the framework of the fiber bundle model subject to the local load sharing rule in which the load of the broken fiber is transferred only to its neighbor fibers. Although the load sharing is strictly local, it is found that the critical behavior belongs to the universality class of the global load sharing where the load is transferred equally to all fibers in the system. From the numerical simulations and the analytical appr...
Bundling telecommunications services : competitive strategies for converging markets.
Krämer, Jan
2009-01-01
With the advent of digital convergence, incumbent telephone and cable companies have begun to offer their services, such as voice telephony, Internet and TV in so-called triple play packages. While carefully recognizing the technological, legal and economic framework of the fixed-line telecommunications industry, this book investigates whether bundling is indeed a profitable pricing strategy for the firms and if it can possibly facilitate the leverage of market power into neighboring markets.
Improving the useful life of a 37-element fuel bundle
International Nuclear Information System (INIS)
Preliminary results indicate that CANDU burnup using 37-element fuel bundle with a slight enrichment can improve the useful life in the core. A slight enrichment in this study is increasing U-235 from 0.72 to 0.9 mass percent. A parametric study on criticality using Atomic Energy of Canada Limited’s WIMSAECL 3.1 and the Monte Carlo code, MCNP 5, developed by Los Alamos National Laboratory, is presented in this paper. (author)
The existence of a kind of bundle map
Institute of Scientific and Technical Information of China (English)
无
2001-01-01
3 By means of the theory of Postnikov resolution, a sufficient condition for the existence of a kind of bundle maps is obtained. Some applications of the result are given. Particularly, it is proven that the deleted products as well as configuration spaces of two simply connected manifolds with suitable dimension have the same homotopy type when the original manifolds are homotopically equivalent.
Bundle Data Approach at GES DISC Targeting Natural Hazards
Shie, Chung-Lin; Shen, Suhung; Kempler, Steven J.
2015-01-01
Severe natural phenomena such as hurricane, volcano, blizzard, flood and drought have the potential to cause immeasurable property damages, great socioeconomic impact, and tragic loss of human life. From searching to assessing the Big, i.e., massive and heterogeneous scientific data (particularly, satellite and model products) in order to investigate those natural hazards, it has, however, become a daunting task for Earth scientists and applications researchers, especially during recent decades. The NASA Goddard Earth Sciences Data and Information Service Center (GES DISC) has served Big Earth science data, and the pertinent valuable information and services to the aforementioned users of diverse communities for years. In order to help and guide our users to online readily (i.e., with a minimum effort) acquire their requested data from our enormous resource at GES DISC for studying their targeted hazard event, we have thus initiated a Bundle Data approach in 2014, first targeting the hurricane event topic. We have recently worked on new topics such as volcano and blizzard. The bundle data of a specific hazard event is basically a sophisticated integrated data package consisting of a series of proper datasets containing a group of relevant (knowledge--based) data variables readily accessible to users via a system-prearranged table linking those data variables to the proper datasets (URLs). This online approach has been developed by utilizing a few existing data services such as Mirador as search engine; Giovanni for visualization; and OPeNDAP for data access, etc. The online Data Cookbook site at GES DISC is the current host for the bundle data. We are now also planning on developing an Automated Virtual Collection Framework that shall eventually accommodate the bundle data, as well as further improve our management in Big Data.
Continuous damage fiber bundle model for strongly disordered materials
Raischel, F.; Kun Ferenc (1966-) (fizikus); Herrmann, Hans J.
2008-01-01
We present an extension of the continuous damage fiber bundle model to describe the gradual degradation of highly heterogeneous materials under an increasing external load. Breaking of a fiber in the model is preceded by a sequence of partial failure events occurring at random threshold values. In order to capture the subsequent propagation and arrest of cracks, furthermore, the disorder of the number of degradation steps of material constituents, the failure thresholds of single fibers are s...
The effects of fee bundling on dental utilization.
Porter, J.; Coyte, P. C.; Barnsley, J.; Croxford, R.
1999-01-01
OBJECTIVE: To examine dental utilization following an adjustment to the provincial fee schedule in which preventive maintenance (recall) services were bundled at lower fees. DATA SOURCES/STUDY SETTING: Blue Cross dental insurance claims for claimants associated with four major Ontario employers using a common insurance plan over the period 1987-1990. STUDY DESIGN: This before-and-after design analyzes the dental claims experience over a four-year period for 4,455 individuals 18 years of age a...
ETA INVARIANTS, DIFFERENTIAL CHARACTERS AND FLAT VECTOR BUNDLES
Institute of Scientific and Technical Information of China (English)
J.M.BISMUT
2005-01-01
The purpose of this paper is to give a refinement of the Atiyah-Singer families index theorem at the level of differential characters. Also a Riemann-Roch-Grothendieck theorem for the direct image of flat vector bundles by proper submersions is proved,with Chern classes with coefficients in C/Q. These results are much related to prior work of Gillet-Soule, Bismut-Lott and Lott.
Fuel element bundle shears with dust extraction when cutting
International Nuclear Information System (INIS)
To prevent deposits of dust when cutting in this very inaccessible area of the fuel element bundle shears, a grating is fitted, which is connected via extraction devices (a collecting funnel and extraction duct) to the downward shaft carrying flushing air for the pipe pieces cut off. The measures taken make it possible to remove dust during cutting by the joint action of flushing air and gravity. (orig./HP)
Image processing for cameras with fiber bundle image relay.
Olivas, Stephen J; Arianpour, Ashkan; Stamenov, Igor; Morrison, Rick; Stack, Ron A; Johnson, Adam R; Agurok, Ilya P; Ford, Joseph E
2015-02-10
Some high-performance imaging systems generate a curved focal surface and so are incompatible with focal plane arrays fabricated by conventional silicon processing. One example is a monocentric lens, which forms a wide field-of-view high-resolution spherical image with a radius equal to the focal length. Optical fiber bundles have been used to couple between this focal surface and planar image sensors. However, such fiber-coupled imaging systems suffer from artifacts due to image sampling and incoherent light transfer by the fiber bundle as well as resampling by the focal plane, resulting in a fixed obscuration pattern. Here, we describe digital image processing techniques to improve image quality in a compact 126° field-of-view, 30 megapixel panoramic imager, where a 12 mm focal length F/1.35 lens made of concentric glass surfaces forms a spherical image surface, which is fiber-coupled to six discrete CMOS focal planes. We characterize the locally space-variant system impulse response at various stages: monocentric lens image formation onto the 2.5 μm pitch fiber bundle, image transfer by the fiber bundle, and sensing by a 1.75 μm pitch backside illuminated color focal plane. We demonstrate methods to mitigate moiré artifacts and local obscuration, correct for sphere to plane mapping distortion and vignetting, and stitch together the image data from discrete sensors into a single panorama. We compare processed images from the prototype to those taken with a 10× larger commercial camera with comparable field-of-view and light collection. PMID:25968031
Functorial QFT, Gauge Anomalies and the Dirac Determinant Bundle
Mickelsson, J; Mickelsson, Jouko; Scott, Simon
1999-01-01
Using properties of the determinant line bundle for a family of elliptic boundary value problems, we explain how the Fock space functor defines an axiomatic quantum field theory which formally models the Fermionic path integral. The 'sewing axiom' of the theory arises as an algebraic pasting law for the determinant of the Dirac operator. We show how representations of the boundary gauge group fit into this description and that this leads to a Fock functor description of certain gauge anomalies.
Stable chains and vortex equations on complex vector bundles
International Nuclear Information System (INIS)
In this paper, we study an object on almost Hermitian manifold M consisting of a finite number of Ji-holomorphic vector bundles Ei over M and homomorphisms φi:E1→Ei-1. We call such an object a J-holomorphic chain. We then prove a Hitchin-Kobayashi correspondence relating the existence of solutions to certain chain vortex equations and an appropriate notion of stability for the corresponding chains. (author)
Heat transfer augmentation in rod bundles near grid spacers
International Nuclear Information System (INIS)
Heat transfer augmentation by straight grid spacers in rod bundles is studied for single phase flow and for post critical heat flux dispersed flow. The heat transfer effect of swirling grid spacers in single phase flow is also examined. Governing heat transfer mechanisms are analyzed, and predictive formulations are established. For single phase flow, the local heat transfer at a straight spacer and at its upstream or downstream locations are treated separately. 18 refs
Wrap groups of fiber bundles over quaternions and octonions
Ludkovsky, S. V.
2008-01-01
This article is devoted to the investigation of wrap groups of connected fiber bundles over the fields of real $\\bf R$, complex $\\bf C$ numbers, the quaternion skew field $\\bf H$ and the octonion algebra $\\bf O$. These groups are constructed with mild conditions on fibers. Their examples are given. It is shown, that these groups exist and for differentiable fibers have the infinite dimensional Lie groups structure, that is, they are continuous or differentiable manifolds and the composition $...
Downflow film boiling in a rod bundle at low pressure
International Nuclear Information System (INIS)
A series of low pressure downflow film boiling heat transfer experiments were conducted in a 14-foot (4.27 m) long electrically heater rod bundle containing 336 heater rods. The resulting data was compared with the Dougall-Rohsenow dispersed flow film boiling correlation. The data was found to lie below this correlation as the quality was increased. It is believed that buoyancy effects decreased the heat transfer in downflow film boiling. (author)
Isolated Left Bundle Branch Block in a Toddler
Hitesh Agrawal; Frank Zimmerman; Zahra Naheed
2014-01-01
Left bundle branch block (LBBB) usually occurs as a postoperative complication from surgical correction of congenital heart disease and can be associated with hypertensive heart disease, coronary artery disease, myocarditis, and aortic valvular disease. Although isolated LBBB is a conduction abnormality found in some healthy adults, it has not been reported in pediatric population. We report a 2-year-old, healthy African American female who was incidentally discovered to have isolated LBBB th...
Diffeological Clifford algebras and pseudo-bundles of Clifford modules
Pervova, Ekaterina
2015-01-01
We consider the diffeological version of the Clifford algebra of a (diffeological) finite-dimensional vector space; we start by commenting on the notion of a diffeological algebra (which is the expected analogue of the usual one) and that of a diffeological module (also an expected counterpart of the usual notion). After considering the natural diffeology of the Clifford algebra, and its expected properties, we turn to our main interest, which is constructing pseudo-bundles of diffeological C...
Conductive Polymer Combined Silk Fiber Bundle for Bioelectrical Signal Recording
Shingo Tsukada; Hiroshi Nakashima; Keiichi Torimitsu
2012-01-01
Electrode materials for recording biomedical signals, such as electrocardiography (ECG), electroencephalography (EEG) and evoked potentials data, are expected to be soft, hydrophilic and electroconductive to minimize the stress imposed on living tissue, especially during long-term monitoring. We have developed and characterized string-shaped electrodes made from conductive polymer with silk fiber bundles (thread), which offer a new biocompatible stress free interface with living tissue in bot...
Local heat transfer coefficient for turbulent flow in rod bundles
International Nuclear Information System (INIS)
The correlation of the local heat transfer coefficients in heated triangular array of rod bundles, in terms of the flow hydrodynamic parameters is presented. The analysis is made first for fluid with Prandtl numbers varying from moderated to high (Pr>0.2), and then extended to fluids with low Prandtl numbers (0.004< Pr<0.2). Results of temperature and velocity fields distribution of slip coefficients and local heat transfer coefficients are obtained. (E.G.)
"Bundle Data" Approach at GES DISC Targeting Natural Hazards
Shie, C. L.; Shen, S.; Kempler, S. J.
2015-12-01
Severe natural phenomena such as hurricane, volcano, blizzard, flood and drought have the potential to cause immeasurable property damages, great socioeconomic impact, and tragic loss of human life. From searching to assessing the "Big", i.e., massive and heterogeneous scientific data (particularly, satellite and model products) in order to investigate those natural hazards, it has, however, become a daunting task for Earth scientists and applications researchers, especially during recent decades. The NASA Goddard Earth Sciences Data and Information Service Center (GES DISC) has served "Big" Earth science data, and the pertinent valuable information and services to the aforementioned users of diverse communities for years. In order to help and guide our users to online readily (i.e., with a minimum effort) acquire their requested data from our enormous resource at GES DISC for studying their targeted hazard/event, we have thus initiated a "Bundle Data" approach in 2014, first targeting the hurricane event/topic. We have recently worked on new topics such as volcano and blizzard. The "bundle data" of a specific hazard/event is basically a sophisticated integrated data package consisting of a series of proper datasets containing a group of relevant ("knowledge-based") data variables readily accessible to users via a system-prearranged table linking those data variables to the proper datasets (URLs). This online approach has been developed by utilizing a few existing data services such as Mirador as search engine; Giovanni for visualization; and OPeNDAP for data access, etc. The online "Data Cookbook" site at GES DISC is the current host for the "bundle data". We are now also planning on developing an "Automated Virtual Collection Framework" that shall eventually accommodate the "bundle data", as well as further improve our management in "Big Data".
Local thermal-hydraulic behaviour in tight 7-rod bundles
Energy Technology Data Exchange (ETDEWEB)
Cheng, X. [School of Nuclear Science and Engineering, Shanghai Jiao Tong University, Dongchuan Road 800, 200240 Shanghai (China); Institute for Nuclear and Energy Technologies, Research Centre Karlsruhe, Postfach 3640, 76021 Karlsruhe (Germany)], E-mail: chengxu@sjtu.edu.cn; Yu, Y.Q. [School of Nuclear Science and Engineering, Shanghai Jiao Tong University, Dongchuan Road 800, 200240 Shanghai (China)
2009-10-15
Advanced water-cooled reactor concepts with tight lattices have been proposed worldwide to improve the fuel utilization and the economic competitiveness. In the present work, experimental investigations were performed on thermal-hydraulic behaviour in tight hexagonal 7-rod bundles under both single-phase and two-phase conditions. Freon-12 was used as working fluid due to its convenient operating parameters. Tests were carried out under both single-phase and two-phase flow conditions. Rod surface temperatures are measured at a fixed axial elevation and in various circumferential positions. Test data with different radial power distributions are analyzed. Measured surface temperatures of unheated rods are used for the assessment of and comparison with numerical codes. In addition, numerical simulation using sub-channel analysis code MATRA and the computational fluid dynamics (CFD) code ANSYS-10 is carried out to understand the experimental data and to assess the validity of these codes in the prediction of flow and heat transfer behaviour in tight rod bundle geometries. Numerical results are compared with experimental data. A good agreement between the measured temperatures on the unheated rod surface and the CFD calculation is obtained. Both sub-channel analysis and CFD calculation indicates that the turbulent mixing in the tight rod bundle is significantly stronger than that computed with a well established correlation.
Experimental study on critical heat flux with long rod bundle
International Nuclear Information System (INIS)
Some new structural features of a long rod bundle test section with experimental method of a type appropriate to the circumstances, data processing and research results are described. The experiments have been performed at a high pressure heat transfer loop. The arrangement of the rod bundle is 3 x 3, square. The rod diameter is 9.5mm, pitch 12.6mm. The effective heating length of each rod is 2200mm. Water or steam-water mixture flows through the rod bundle upwards. The axial heat flux profiles are uniformly distributed. Parameter ranges for the experiments are pressures from 14.4 to 15.7MPa, mass velocities from 1200 to 3540kg/(m2·s) and burnout qualities from -17% to +15%. The data processing for a total of 95 CHF data points is carried out on VAX computer. The formula for predicting CHF values presened can be used in a field of thermal hydraulic design and safety analysis for PWR
Evaluating pulp stiffness from fibre bundles by ultrasound
Karppinen, Timo; Montonen, Risto; Määttänen, Marjo; Ekman, Axel; Myllys, Markko; Timonen, Jussi; Hæggström, Edward
2012-06-01
A non-destructive ultrasonic tester was developed to measure the stiffness of pulp bundles. The mechanical properties of pulp are important when estimating the behaviour of paper under stress. Currently available pulp tests are tedious and alter the fibres structurally and mechanically. The developed tester employs (933 ± 15) kHz tweezer-like ultrasonic transducers and time-of-flight measurement through (9.0 ± 2.5) mm long and (0.8 ± 0.1) mm thick fibre bundles kept at (19.1 ± 0.4) °C and (62 ± 1)% RH. We determined the stiffness of soft wood pulps produced by three kraft pulping modifications: standard kraft pulp, (5.2 ± 0.4) GPa, prehydrolysis kraft pulp, (4.3 ± 0.4) GPa, and alkali extracted prehydrolysis kraft pulp, (3.3 ± 0.4) GPa. Prehydrolysis and alkali extraction processes mainly lowered the hemicellulose content of the pulps, which essentially decreased the fibre-wall stiffness hence impairing the stiffness of the fibre networks. Our results indicate that the method allows ranking of pulps according to their stiffness determined from bundle-like samples taken at an early phase of the papermaking process.
Evaluating pulp stiffness from fibre bundles by ultrasound
International Nuclear Information System (INIS)
A non-destructive ultrasonic tester was developed to measure the stiffness of pulp bundles. The mechanical properties of pulp are important when estimating the behaviour of paper under stress. Currently available pulp tests are tedious and alter the fibres structurally and mechanically. The developed tester employs (933 ± 15) kHz tweezer-like ultrasonic transducers and time-of-flight measurement through (9.0 ± 2.5) mm long and (0.8 ± 0.1) mm thick fibre bundles kept at (19.1 ± 0.4) °C and (62 ± 1)% RH. We determined the stiffness of soft wood pulps produced by three kraft pulping modifications: standard kraft pulp, (5.2 ± 0.4) GPa, prehydrolysis kraft pulp, (4.3 ± 0.4) GPa, and alkali extracted prehydrolysis kraft pulp, (3.3 ± 0.4) GPa. Prehydrolysis and alkali extraction processes mainly lowered the hemicellulose content of the pulps, which essentially decreased the fibre-wall stiffness hence impairing the stiffness of the fibre networks. Our results indicate that the method allows ranking of pulps according to their stiffness determined from bundle-like samples taken at an early phase of the papermaking process. (paper)
Real bundle gerbes, orientifolds and twisted KR-homology
Hekmati, Pedram; Szabo, Richard J; Vozzo, Raymond F
2016-01-01
We introduce a notion of Real bundle gerbes on manifolds equipped with an involution. We elucidate their relation to Jandl gerbes and prove that they are classified by their Real Dixmier-Douady class in Grothendieck's equivariant sheaf cohomology. We show that the Grothendieck group of Real bundle gerbe modules is isomorphic to twisted KR-theory for a torsion Real Dixmier-Douady class. Building on the Baum-Douglas model for K-homology and the orientifold construction in string theory, we introduce geometric cycles for twisted KR-homology groups using Real bundle gerbe modules. We prove that this defines a real-oriented generalised homology theory dual to twisted KR-theory for Real closed manifolds, and more generally for Real finite CW-complexes, for any Real Dixmier-Douady class. This is achieved by defining an explicit natural transformation to analytic twisted KR-homology and proving that it is an isomorphism. Our constructions give a new framework for the classification of orientifolds in string theory, p...
Ab initio study of MoS2 nanotube bundles
Verstraete, Matthieu; Charlier, Jean-Christophe
2003-07-01
Recently, the synthesis of a new phase of MoS2I1/3 stoichiometry was reported [M. Remskar, A. Mrzel, Z. Skraba, A. Jesih, M. Ceh, J. Demšar, P. Stadelmann, F. Lévy, and D. Mihailovic, Science 292, 479 (2001)]. Electron microscope images and diffraction data were interpreted to indicate bundles of sub-nanometer-diameter single-wall MoS2 nanotubes. After experimental characterization, the structure was attributed to an assembly of “armchair” nanotubes with interstitial iodine. Using first-principles total-energy calculations, bundles of MoS2 nanotubes with different topologies and stoichiometries are investigated. All of the systems are strongly metallic. Configurations with “zigzag” structures are found to be more stable energetically than the “armchair” ones, though all of the structures have similar stabilities. After relaxation, there remain several candidates which give a lattice parameter in relative agreement with experiment. Further, spin-polarized calculations indicate that a structure with armchair tubes iodine atoms in their center acquires a very large spontaneous magnetic moment of 12μB, while the other structures are nonmagnetic. Our ab initio calculations show that in most of the other structures, the tubes are very strongly bound together, and that the compounds should be considered as a crystal, rather than as a bundle of tubes in the habitual sense.
Enhanced boiling heat transfer in horizontal test bundles
Energy Technology Data Exchange (ETDEWEB)
Trewin, R.R.; Jensen, M.K.; Bergles, A.E.
1994-08-01
Two-phase flow boiling from bundles of horizontal tubes with smooth and enhanced surfaces has been investigated. Experiments were conducted in pure refrigerant R-113, pure R-11, and mixtures of R-11 and R-113 of approximately 25, 50, and 75% of R-113 by mass. Tests were conducted in two staggered tube bundles consisting of fifteen rows and five columns laid out in equilateral triangular arrays with pitch-to-diameter ratios of 1.17 and 1.5. The enhanced surfaces tested included a knurled surface (Wolverine`s Turbo-B) and a porous surface (Linde`s High Flux). Pool boiling tests were conducted for each surface so that reference values of the heat transfer coefficient could be obtained. Boiling heat transfer experiments in the tube bundles were conducted at pressures of 2 and 6 bar, heat flux values from 5 to 80 kW/m{sup 2}s, and qualities from 0% to 80%, Values of the heat transfer coefficients for the enhanced surfaces were significantly larger than for the smooth tubes and were comparable to the values obtained in pool boiling. It was found that the performance of the enhanced tubes could be predicted using the pool boiling results. The degradation in the smooth tube heat transfer coefficients obtained in fluid mixtures was found to depend on the difference between the molar concentration in the liquid and vapor.
Gaining Surgical Access for Repositioning the Inferior Alveolar Neurovascular Bundle
Directory of Open Access Journals (Sweden)
Saif Yousif Abdullah Al-Siweedi
2014-01-01
Full Text Available This study is aimed at determining anatomical landmarks that can be used to gain access to the inferior alveolar neurovascular (IAN bundle. Scanned CBCT (i-CAT machine data of sixty patients and reconstructions performed using the SimPlant dental implant software were reviewed. Outcome variables were the linear distances of the mandibular canal to the inferior border and the buccal cortex of the mandible, measured immediately at the mental foramen (D1 and at 10, 20, 30, and 40 mm (D2–D5 distal to it. Predictor variables were age, ethnicity, and gender of subjects. Apicobasal assessment of the canal reveals that it is curving downward towards the inferior mandibular border until 20 mm (D3 distal to the mental foramen where it then curves upwards, making an elliptic-arc curve. The mandibular canal also forms a buccolingually oriented elliptic arc in relation to the buccal cortex. Variations due to age, ethnicity, and gender were evident and this study provides an accurate anatomic zone for gaining surgical access to the IAN bundle. The findings indicate that the buccal cortex-IAN distance was greatest at D3. Therefore, sites between D2 and D5 can be used as favorable landmarks to access the IAN bundle with the least complications to the patient.
Mass Transport Through Carbon Nanotube-Polystyrene Bundles
Lin, Rongzhou; Tran, Tuan
2016-05-01
Carbon nanotubes have been widely used as test channels to study nanofluidic transport, which has been found to have distinctive properties compared to transport of fluids in macroscopic channels. A long-standing challenge in the study of mass transport through carbon nanotubes (CNTs) is the determination of flow enhancement. Various experimental investigations have been conducted to measure the flow rate through CNTs, mainly based on either vertically aligned CNT membranes or individual CNTs. Here, we proposed an alternative approach that can be used to quantify the mass transport through CNTs. This is a simple method relying on the use of carbon nanotube-polystyrene bundles, which are made of CNTs pulled out from a vertically aligned CNT array and glued together by polystyrene. We experimentally showed by using fluorescent tagging that the composite bundles allowed measureable and selective mass transport through CNTs. This type of composite bundle may be useful in various CNT research areas as they are simple to fabricate, less likely to form macroscopic cracks, and offer a high density of CNT pores while maintaining the aligned morphology of CNTs.
Lateral mechanical coupling of stereocilia in cochlear hair bundles.
Langer, M G; Fink, S; Koitschev, A; Rexhausen, U; Hörber, J K; Ruppersberg, J P
2001-06-01
For understanding the gating process of transduction channels in the inner ear it is essential to characterize and examine the functional properties of the ultrastructure of stereociliary bundles. There is strong evidence that transduction channels in hair cells are gated by directly pulling at the so-called tip links. In addition to these tip links a second class of filamentous structures was identified in the scanning and transmission electron microscope: the side-to-side links. These links laterally connect stereocilia of the same row of a hair bundle. This study concentrates on mechanical coupling of stereocilia of the tallest row connected by side-to-side links. Atomic Force microscopy (AFM) was used to investigate hair bundles of outer hair cells (OHCs) from postnatal rats (day 4). Although hair bundles of postnatal rats are still immature at day 4 and interconnecting cross-links do not show preferential direction yet, hair bundles of investigated OHCs already showed the characteristic V-shape of mature hair cells. In a first experiment, the stiffness of stereocilia was investigated scanning individual stereocilia with an AFM tip. The spring constant for the excitatory direction was 2.5 +/- 0.6 x 10(-3) N/m whereas a higher spring constant (3.1 +/- 1.5 x 10(-3) N/m) was observed in the inhibitory direction. In a second set of experiments, the force transmission between stereocilia of the tallest row was measured using AFM in combination with a thin glass fiber. This fiber locally displaced a stereocilium while the force laterally transmitted to the neighboring untouched taller stereocilia was measured by AFM. The results show a weak force interaction between tallest stereocilia of postnatal rats. The force exerted to an individual stereocilium declines to 36% at the nearest adjacent stereocilium of the same row not touched with the fiber. It is suggested that the amount of force transmitted from a taller stereocilium to an adjacent one of the same row depends
HLM fuel pin bundle experiments in the CIRCE pool facility
Energy Technology Data Exchange (ETDEWEB)
Martelli, Daniele, E-mail: daniele.martelli@ing.unipi.it [University of Pisa, Department of Civil and Industrial Engineering, Pisa (Italy); Forgione, Nicola [University of Pisa, Department of Civil and Industrial Engineering, Pisa (Italy); Di Piazza, Ivan; Tarantino, Mariano [Italian National Agency for New Technologies, Energy and Sustainable Economic Development, C.R. ENEA Brasimone (Italy)
2015-10-15
Highlights: • The experimental results represent the first set of values for LBE pool facility. • Heat transfer is investigated for a 37-pin electrical bundle cooled by LBE. • Experimental data are presented together with a detailed error analysis. • Nu is computed as a function of the Pe and compared with correlations. • Experimental Nu is about 25% lower than Nu derived from correlations. - Abstract: Since Lead-cooled Fast Reactors (LFR) have been conceptualized in the frame of GEN IV International Forum (GIF), great interest has focused on the development and testing of new technologies related to HLM nuclear reactors. In this frame the Integral Circulation Experiment (ICE) test section has been installed into the CIRCE pool facility and suitable experiments have been carried out aiming to fully investigate the heat transfer phenomena in grid spaced fuel pin bundles providing experimental data in support of European fast reactor development. In particular, the fuel pin bundle simulator (FPS) cooled by lead bismuth eutectic (LBE), has been conceived with a thermal power of about 1 MW and a uniform linear power up to 25 kW/m, relevant values for a LFR. It consists of 37 fuel pins (electrically simulated) placed on a hexagonal lattice with a pitch to diameter ratio of 1.8. The FPS was deeply instrumented by several thermocouples. In particular, two sections of the FPS were instrumented in order to evaluate the heat transfer coefficient along the bundle as well as the cladding temperature in different ranks of sub-channels. Nusselt number in the central sub-channel was therefore calculated as a function of the Peclet number and the obtained results were compared to Nusselt numbers obtained from convective heat transfer correlations available in literature on Heavy Liquid Metals (HLM). Results reported in the present work, represent the first set of experimental data concerning fuel pin bundle behaviour in a heavy liquid metal pool, both in forced and
Compactifications of the Heterotic string with unitary bundles
Energy Technology Data Exchange (ETDEWEB)
Weigand, T.
2006-05-23
In this thesis we investigate a large new class of four-dimensional supersymmetric string vacua defined as compactifications of the E{sub 8} x E{sub 8} and the SO(32) heterotic string on smooth Calabi-Yau threefolds with unitary gauge bundles and heterotic five-branes. The first part of the thesis discusses the implementation of this idea into the E{sub 8} x E{sub 8} heterotic string. After specifying a large class of group theoretic embeddings featuring unitary bundles, we analyse the effective four-dimensional N=1 supergravity upon compactification. From the gauge invariant Kaehler potential for the moduli fields we derive a modification of the Fayet-Iliopoulos D-terms arising at one-loop in string perturbation theory. From this we conjecture a one-loop deformation of the Hermitian Yang-Mills equation and introduce the idea of {lambda}-stability as the perturbatively correct stability concept generalising the notion of Mumford stability valid at tree-level. We then proceed to a definition of SO(32) heterotic vacua with unitary gauge bundles in the presence of heterotic five-branes and find agreement of the resulting spectrum with the S-dual framework of Type I/Type IIB orientifolds. A similar analysis of the effective four-dimensional supergravity is performed. Further evidence for the proposed one-loop correction to the stability condition is found by identifying the heterotic corrections as the S-dual of the perturbative part of {pi}-stability as the correct stability concept in Type IIB theory. After reviewing the construction of holomorphic stable vector bundles on elliptically fibered Calabi-Yau manifolds via spectral covers, we provide semi-realistic examples for SO(32) heterotic vacua with Pati-Salam and MSSM-like gauge sectors. We finally discuss the construction of realistic vacua with flipped SU(5) GUT and MSSM gauge group within the E{sub 8} x E{sub 8} framework, based on the embedding of line bundles into both E{sub 8} factors. Some of the appealing
Effect of Candu Fuel Bundle Modeling on Sever Accident Analysis
Energy Technology Data Exchange (ETDEWEB)
Dupleac, D.; Prisecaru, I. [Power Plant Engineering Faculty, Politehnica University, 313 Splaiul Independentei, 060042, sect. 6, Bucharest (Romania); Mladin, M. [Institute for Nuclear Research, Pitesti-Mioveni, 115400 (Romania)
2009-06-15
In a Candu 6 nuclear power reactor fuel bundles are located in horizontal Zircaloy pressure tubes through which the heavy-water coolant flows. Each pressure tube is surrounded by a concentric calandria tube. Outside the calandria tubes is the heavy-water moderator contained in the calandria itself. The moderator is maintained at a temperature of 70 deg. C by a separate cooling circuit. The moderator surrounding the calandria tubes provides a potential heat sink following a loss of core heat removal. The calandria vessel is in turn contained within a shield tank (or reactor vault), which provides biological shielding during normal operation and maintenance. It is a large concrete tank filled with ordinary water. During normal operation, about 0.4% of the core's thermal output is deposited in the shield tank and end shields, through heat transfer from the calandria structure and fission heating. In a severe accident scenario, the shield tank could provide an external calandria vessel cooling which can be maintained until the shield tank water level drops below the debris level. The Candu system design has specific features which are important to severe accidents progression and requires selective consideration of models, methods and techniques of severe accident evaluation. Moreover, it should be noted that the mechanistic models for severe accident in Candu system are largely less well validated and as the result the level of uncertainty remains high in many instances. Unlike the light water reactors, for which are several developed computer codes to analyze severe accidents, for Candu severe accidents analysis two codes were developed: MAAP4-Candu and ISAAC. However, both codes started by using MAAP4/PWR as reference code and implemented Candu 6 specific models. Thus, these two codes had many common features. Recently, a joint project involving Romanian nuclear organizations and coordinated by Politehnica University of Bucharest has been started. The purpose
Double-bundle depiction of the anterior cruciate ligament at 3 Tesla
International Nuclear Information System (INIS)
Magnetic resonance imaging on 3 Tesla (3T MRI) with arthroscopic correlation has proven to adequately identify the anteromedial bundle (AMB) and posterolateral bundle (PLB) in cadaver knees. The purpose of this study was to describe the depiction of ACL bundle anatomy on 3T MRI in daily practice. In a retrospective cohort study, we included 50 consecutive patients who underwent standard 3T MRI of the knee and had an intact ACL. Two musculoskeletal radiologists independently reviewed all scans for depiction of ACL bundle anatomy using standardized forms. Descriptive statistics were used. Twenty-three right knees (46%) and 27 left knees (54%) were included in the study. Mean age of the patients was 35 years (range 12 to 68 years); 37 patients were male (74%). ACL bundle anatomy was best depicted in the axial plane in 44 knees (88%) and in the coronal plane in six knees (12%). Two bundles were seen in 47 knees (94%). The AMB was completely seen in 45 knees (90%). The PLB was completely seen in 40 knees (80%). Both bundles were completely seen in 37 knees (76%). The double-bundle anatomy of the ACL is visualized in 94% of patients on 3T MRI. Because of potentially associated clinical benefits, we advocate to report separately on the anteromedial bundle and posterolateral bundle in case of anterior cruciate ligament injury of the knee. (orig.)
Double-bundle depiction of the anterior cruciate ligament at 3 Tesla
Energy Technology Data Exchange (ETDEWEB)
Adriaensen, M.E.A.P.M. [Atrium Medical Center Parkstad, Department of Radiology, Heerlen (Netherlands); Hogan, B. [Sports Surgery Clinic, Department of Radiology, Dublin (Ireland); Al-Bulushi, H.I.J. [Armed Forces Hospital, Department of Radiology, Muscat (Oman); Kavanagh, E.C. [Mater Misericordiae Hospital, Department of Radiology, Dublin (Ireland)
2012-07-15
Magnetic resonance imaging on 3 Tesla (3T MRI) with arthroscopic correlation has proven to adequately identify the anteromedial bundle (AMB) and posterolateral bundle (PLB) in cadaver knees. The purpose of this study was to describe the depiction of ACL bundle anatomy on 3T MRI in daily practice. In a retrospective cohort study, we included 50 consecutive patients who underwent standard 3T MRI of the knee and had an intact ACL. Two musculoskeletal radiologists independently reviewed all scans for depiction of ACL bundle anatomy using standardized forms. Descriptive statistics were used. Twenty-three right knees (46%) and 27 left knees (54%) were included in the study. Mean age of the patients was 35 years (range 12 to 68 years); 37 patients were male (74%). ACL bundle anatomy was best depicted in the axial plane in 44 knees (88%) and in the coronal plane in six knees (12%). Two bundles were seen in 47 knees (94%). The AMB was completely seen in 45 knees (90%). The PLB was completely seen in 40 knees (80%). Both bundles were completely seen in 37 knees (76%). The double-bundle anatomy of the ACL is visualized in 94% of patients on 3T MRI. Because of potentially associated clinical benefits, we advocate to report separately on the anteromedial bundle and posterolateral bundle in case of anterior cruciate ligament injury of the knee. (orig.)
International Nuclear Information System (INIS)
To model thermal mechanical bundle deformation behaviour under high temperature conditions, several factors need to be considered. These are the sources of loads, deformation mechanisms, interactions within bundle components, bundle and pressure tube (PT) interaction, and boundary constraints on the fuel bundles under in-reactor conditions. This paper describes the modelling of the following three processes: Bundle slumping due to high temperature creep-sag of individual elements and endplates; Differential element expansion and fuel element bowing; and, Bundle distortion under axial loads. To model these processes, a number of key mechanisms for bundle deformation must be considered, which include: 1) Interaction of fuel elements in a bundle with their neighbours, 2) Endplate deformation, 3) Fuel elements lateral deformation under various loads and mechanisms, 4) Interaction within a fuel element, 5) Material property change at high temperatures, 6) Transient response of a bundle, and 7) Bundle configuration change. This paper summarises the new models needed for the mechanistic modelling of the key mechanisms mentioned above and provides an example to show how an endplate plasticity model is developed with results. (author)
High-resolution flow structure measurements in a rod bundle
International Nuclear Information System (INIS)
Flow behaviour inside a rod bundle has been an active research topic since the early days of the nuclear power industry. Of particular interest in previous studies have been topics such as flow mixing, two-phase flow structure and mapping of two-phase flow transitions. The optimisation of fuel element design can only be achieved by truly understanding the nature of flow. The ultimate goal in this research is to enhance the heat transfer and increase the critical heat flux, which would improve the fuel economy. A better understanding of the flow would also improve nuclear safety as departure from nucleate boiling (DNB) can be predicted more accurately. The motivation for the current project (SUBFLOW) was to increase knowledge of the complex flow phenomena inside a rod bundle. A dedicated sub-channel flow test facility was designed and constructed at the Paul Scherrer Institut (PSI), Villigen, Switzerland. An adiabatic test loop has an up-scaled (1:2.6) vertical fuel rod bundle model with a 4 × 4 geometry. For the very first time, the wire-mesh sensor measurement technique was implemented in a rod bundle as two 64×64 conductivity wire-mesh sensors were installed in the upper part of the test section. The measurement technique enables one to study single- and two-phase flow behaviour with high spatial and temporal resolution. The research topics addressed in this thesis cover a wide range of flow conditions with and without a spacer grid in a rod bundle. The experimental campaign was started by studying natural mixing of a passive scalar to characterise the development of turbulent diffusion in an injection sub-channel and, later on, cross-mixing between adjacent sub-channels. The results were also used in comparison with the in-house CFD code PSI-Boil that is being developed at PSI. The code could estimate the mixing inside the sub-channel and the transition to cross-mixing with a good accuracy. As a natural transition, the SUBFLOW experiments were continued by
High-resolution flow structure measurements in a rod bundle
Energy Technology Data Exchange (ETDEWEB)
Ylönen, A. T.
2013-07-01
Flow behaviour inside a rod bundle has been an active research topic since the early days of the nuclear power industry. Of particular interest in previous studies have been topics such as flow mixing, two-phase flow structure and mapping of two-phase flow transitions. The optimisation of fuel element design can only be achieved by truly understanding the nature of flow. The ultimate goal in this research is to enhance the heat transfer and increase the critical heat flux, which would improve the fuel economy. A better understanding of the flow would also improve nuclear safety as departure from nucleate boiling (DNB) can be predicted more accurately. The motivation for the current project (SUBFLOW) was to increase knowledge of the complex flow phenomena inside a rod bundle. A dedicated sub-channel flow test facility was designed and constructed at the Paul Scherrer Institut (PSI), Villigen, Switzerland. An adiabatic test loop has an up-scaled (1:2.6) vertical fuel rod bundle model with a 4 × 4 geometry. For the very first time, the wire-mesh sensor measurement technique was implemented in a rod bundle as two 64×64 conductivity wire-mesh sensors were installed in the upper part of the test section. The measurement technique enables one to study single- and two-phase flow behaviour with high spatial and temporal resolution. The research topics addressed in this thesis cover a wide range of flow conditions with and without a spacer grid in a rod bundle. The experimental campaign was started by studying natural mixing of a passive scalar to characterise the development of turbulent diffusion in an injection sub-channel and, later on, cross-mixing between adjacent sub-channels. The results were also used in comparison with the in-house CFD code PSI-Boil that is being developed at PSI. The code could estimate the mixing inside the sub-channel and the transition to cross-mixing with a good accuracy. As a natural transition, the SUBFLOW experiments were continued by
Semistable vector bundles and Tannaka duality from a computational point of view
Kaid, Almar
2011-01-01
We develop a semistability algorithm for vector bundles which are given as a kernel of a surjective morphism between splitting bundles on the projective space over an algebraically closed field K. This class of bundles is a generalization of syzygy bundles. We show how to implement this algorithm in a computer algebra system. Further we give applications, mainly concerning the computation of Tannaka dual groups of stable vector bundles of degree 0 on the projective space and on certain smooth complete intersection curves. We also use our algorithm to close a gap in a recent work of L. Costa, P. Macias Marques and R. M. Miro-Roig regarding the stability of the syzygy bundle of general forms. Finally, we apply our algorithm to provide a computational approach to tight closure. All algorithms are implemented in the computer algebra system CoCoA
Hydrodynamic behavior of a bare rod bundle. [LMFBR
Energy Technology Data Exchange (ETDEWEB)
Bartzis, J.G.; Todreas, N.E.
1977-06-01
The temperature distribution within the rod bundle of a nuclear reactor is of major importance in nuclear reactor design. However temperature information presupposes knowledge of the hydrodynamic behavior of the coolant which is the most difficult part of the problem due to complexity of the turbulence phenomena. In the present work a 2-equation turbulence model--a strong candidate for analyzing actual three dimensional turbulent flows--has been used to predict fully developed flow of infinite bare rod bundle of various aspect ratios (P/D). The model has been modified to take into account anisotropic effects of eddy viscosity. Secondary flow calculations have been also performed although the model seems to be too rough to predict the secondary flow correctly. Heat transfer calculations have been performed to confirm the importance of anisotropic viscosity in temperature predictions. All numerical calculations for flow and heat have been performed by two computer codes based on the TEACH code. Experimental measurements of the distribution of axial velocity, turbulent axial velocity, turbulent kinetic energy and radial Reynolds stresses were performed in the developing and fully developed regions. A 2-channel Laser Doppler Anemometer working on the Reference mode with forward scattering was used to perform the measurements in a simulated interior subchannel of a triangular rod array with P/D = 1.124. Comparisons between the analytical results and the results of this experiment as well as other experimental data in rod bundle array available in literature are presented. The predictions are in good agreement with the results for the high Reynolds numbers.
Noise alters hair-bundle mechanics at the cochlear apex
Strimbu, C. Elliott; Fridberger, Anders
2015-12-01
Exposure to loud sounds can lead to both permanent and short term changes in auditory sensitivity. Permanent hearing loss is often associated with gross changes in cochlear morphology including the loss of hair cells and auditory nerve fibers while the mechanisms of short term threshold shifts are much less well understood and may vary at different locations across the cochlea. Previous reports suggest that exposure to loud sounds leads to a decrease in the cochlear microphonic potential and in the stiffness of the organ of Corti. Because the cochlear microphonic reflects changes in the membrane potential of the hair cells, this suggests that hair-bundle motion should be reversibly altered following exposure to loud sounds. Using an in vitro preparation of the guinea pig temporal bone we investigate changes in the micro-mechanical response near the cochlear apex following a brief (up to 10 - 20 minutes) exposure to loud (˜ 120 dB) tones near the best frequency at this location. We use time-resolved confocal imaging to record the motion of outer hair cell bundles before and after acoustic overstimulation. We have also recorded larger-scale structural views of the organ of Corti before and after exposure to the loud sound. Conventional electrophysiological techniques are used measure the cochlear microphonic potential. As has been previously reported, following acoustic overexposure the cochlear microphonic declines in value and typically recovers on the order of 30 - 60 minutes. Hair-bundle trajectories are affected following the loud sound and typically recover on a somewhat faster time scale than the microphonic potential, although the results vary considerably across preparations. Preliminary results also suggest reversible changes in the hair cell's resting potential following the loud sound.
FLP: a field line plotting code for bundle divertor design
International Nuclear Information System (INIS)
A computer code was developed to aid in the design of bundle divertors. The code can handle discrete toroidal field coils and various divertor coil configurations. All coils must be composed of straight line segments. The code runs on the PDP-10 and displays plots of the configuration, field lines, and field ripple. It automatically chooses the coil currents to connect the separatrix produced by the divertor to the outer edge of the plasma and calculates the required coil cross sections. Several divertor designs are illustrated to show how the code works
Noncommutative vector bundles over fuzzy CPN and their covariant derivatives
International Nuclear Information System (INIS)
We generalise the construction of fuzzy CPN in a manner that allows us to access all noncommutative equivariant complex vector bundles over this space. We give a simplified construction of polarization tensors on S2 that generalizes to complex projective space, identify Laplacians and natural noncommutative covariant derivative operators that map between the modules that describe noncommuative sections. In the process we find a natural generalization of the Schwinger-Jordan construction to su(n) and identify composite oscillators that obey a Heisenberg algebra on an appropriate Fock space
Connections on Clifford bundles and the Dirac operator
International Nuclear Information System (INIS)
It is shown, how - in the setting of Clifford bundles - the spin connection (or Dirac operator) may be obtained by averaging the Levi-Civita connection (or Kaehler-Dirac operator) over the finite group generated by an orthonormal frame of the base-manifold. The familiar covariance of the Dirac equation under a simultaneous transformation of spinors and matrix-representations emerges very naturally in this scheme, which can also be applied when the manifold does not possess a spin-structure. (Author)
Visualization of the medial forebrain bundle using diffusion tensor imaging
Directory of Open Access Journals (Sweden)
Ardian Hana
2015-10-01
Full Text Available Diffusion tensor imaging is a technique that enables physicians the portrayal of white matter tracts in vivo. We used this technique in order to depict the medial forebrain bundle in 15 consecutive patients between 2012 and 2015. Men and women of all ages were included. There were 6 women and 9 men. The mean age was 58,6 years (39-77. Nine patients were candidates for an eventual deep brain stimulation. Eight of them suffered from Parkinson`s disease and one had multiple sclerosis. The remaining 6 patients suffered from different lesions which were situated in the frontal lobe. These were 2 metastasis, 2 meningiomas, 1 cerebral bleeding and 1 glioblastoma. We used a 3DT1-sequence for the navigation. Furthermore T2- and DTI- sequences were performed. The FOV was 200 x 200 mm², slice thickness 2 mm, and an acquisition matrix of 96 x 96 yielding nearly isotropic voxels of 2 x 2 x 2 mm. 3-Tesla-MRI was carried out strictly axial using 32 gradient directions and one b0-image. We used Echo-Planar-Imaging (EPI and ASSET parallel imaging with an acceleration factor of 2. b-value was 800 s/mm². The maximal angle was 50°. Additional scanning time was less than 9 minutes. We were able to visualize the medial forebrain bundle in 12 of our patients bilaterally and in the remaining 3 patients we depicted the medial forebrain bundle on one side. It was the contralateral side of the lesion. These were 2 meningiomas and one metastasis. Portrayal of the medial forebrain bundle is possible for everyday routine for neurosurgical interventions. As part of the reward circuitry it might be of substantial importance for neurosurgeons during deep brain stimulation in patients with psychiatric disorders. Furthermore it might explain at a certain extent character changes in patients with lesions in the frontal lobe. Surgery in this part of the brain should always take the preservation of this white matter tract into account.
Thermohydraulic tests of 3x3-rod bundle maquette
International Nuclear Information System (INIS)
The results of a 3x3-rod bundle thermohydraulic research program, performed in the Thermohydraulics Laboratory of NUCLEBRAS' Nuclear Technology Development Center, are briefly described. This program included measurements of pressure drops in one and two-phase flows, heat transfer coefficients, mixing between interconnected subchannels in one-phase flow conditions and critical heat fluxes. The measurements covered the following parameter ranges: heat fluxes from zero to the critical values, pressure ranging from 1 to 15 ata, inlet temperature from 25 to 150 sup(0)C and flow rate from 20 to 300l/min. (author)
Principal Bundles whose Restrictions to a Curve are Isomorphic
Indian Academy of Sciences (India)
Sudarshan Rajendra Gurjar
2011-05-01
Let be a normal projective variety defined over an algebraically closed field . Let $|O_X(1)|$ be a very ample invertible sheaf on . Let be an affine algebraic group defined over . Let $E_G$ and $F_G$ be two principal -bundles on . Then there exists an integer $n \\gg 0$ (depending on $E_G$ and $F_G$) such that if the restrictions of $E_G$ and $F_G$ to a curve $C\\in |O_X(n)|$ are isomorphic, then they are isomorphic on all of .
Numerical simulation of turbulent flow in a rod bundle geometry
International Nuclear Information System (INIS)
This paper presents predictions of turbulent flows in a rod bundle geometry by using the k-ε turbulence model and the Reynolds stress model. Significant difference was not found in the predicted turbulence properties by the two models. The secondary flow predicted by the Reynolds stress model, which was nearly 1.2% of axial bulk velocity, changed the distribution of mean axial velocity, turbulence intensities and Reynolds shear stresses. The Reynolds stress model was unable to estimate the flow pulsation which is the main contribution of turbulent interchange mixing between subchannels. (author)
Numerical simulation of flow-induced vibrations in tube bundles
International Nuclear Information System (INIS)
Full text of publication follows: In many industrial components mechanical structures like rod cluster control assembly, fuel assembly and heat exchanger tube bundles are submitted to complex flows causing possible vibrations and damage. Fluid forces are usually split into two parts: structure motion independent forces and fluid-elastic forces coupled with tube motion and responsible for possible dynamic instability development leading to possible short term failures through high amplitude vibrations. Most classical fluid force identification methods rely on structure response experimental measurements associated with convenient data processes. Owing to recent improvements in Computational Fluid Dynamics (C.F.D.), numerical fluid force identification is now practicable in the presence of industrial configurations. The present paper is devoted to numerical simulation of flow-induced vibrations of tube bundles submitted to single-phase cross flows by using C.F.D. codes. Direct Numerical Simulation (D.N.S.), Arbitrary Lagrange Euler formulation (A.L.E.) and code coupling process are involved to predict fluid forces responsible for tube bundle vibrations in the presence of fluid structure and fluid-elastic coupling effects. In the presence of strong multi-physics coupling, simulation of flow-induced vibrations requires a fluid structure code coupling process. The methodology consists in solving in the same time thermohydraulics and mechanics problems by using an A.L.E. formulation for the fluid computation. The purpose is to take into account coupling between flow and structure motions in order to be able to capture coupling effects. From a numerical point of view, there are three steps in the computation: the fluid problem is solved on the computational domain; fluid forces acting on the moving tube are estimated; finally they are introduced in the structure solver providing the tube displacement that is used to actualize the fluid computational domain. Specific
Gauge Theories and Fiber Bundles: Definitions, Pictures, and Results
Marsh, Adam
2016-01-01
A pedagogical but concise overview of fiber bundles and their connections is provided, in the context of gauge theories in physics. The emphasis is on defining and visualizing concepts and relationships between them, as well as listing common confusions, alternative notations and jargon, and relevant facts and theorems. Special attention is given to detailed figures and geometric viewpoints, some of which would seem to be novel to the literature. Topics are avoided which are well covered in textbooks, such as historical motivations, proofs and derivations, and tools for practical calculations. The present paper is best read in conjunction with the similar paper on Riemannian geometry cited herein.
Spectrum Reorganization and Bundling for Power Efficient Mobile Networks
DEFF Research Database (Denmark)
Micallef, Gilbert; Mogensen, Preben; Scheck, Hans-Otto
2012-01-01
still required for supporting legacy devices and providing wider network coverage. In order to facilitate and reduce the cost of rolling out a new network, mobile operators often reuse existing sites. Radio frequency modules in base station sites house power amplifiers, which are designed to operate...... can be reorganized within a single band, and have multiple carriers bundled together to fully exploit the capabilities of modern equipment. These modifications are applied on all network layers, maintaining the same number of carriers and baseband capacity. For the presented case, this results in the...
Quantum Bundle Description of the Quantum Projective Spaces
Buachalla, Réamonn Ó
2011-01-01
We realise Heckenberger and Kolb's canonical calculus on quantum projective (n-1)-space as the restriction of a distinguished quotient of the standard bicovariant calculus for Cq[SUn]. We introduce a calculus on the quantum (2n-1)-sphere in the same way. With respect to these choices of calculi, we present quantum projective (N-1)-space as the base space of two different quantum principal bundles, one with total space Cq[SUn], and the other with total space Cq[S^(2n-1)]. We go on to give Cq[C...
Parameter design and optimization of tight-lattice rod bundles
International Nuclear Information System (INIS)
Thin rod bundles with tight lattice are arranged according to the equilateral triangle grid, as the proportion of fuel is large, and the power density of core is high. Based on the analysis of the performance of core, the ABV-6M reactor is taken as the example, and two objective functions, power density and flow rate of coolant are proposed for optimization calculation. Diameter and pitch of rod are optimized by using GA method respectively. The results, which are considered to be safety in security checking, show that tight lattice is effective for improving the power density and other performances of the reactor core. (author)
Foliation, jet bundle and quantization of Einstein gravity
Park, I Y
2015-01-01
With the Hamiltonian and Lagrangian analyses in the ADM setup, it was observed in \\cite{Park:2014tia} that the physical configuration space of the 4D Einstein-Hilbert action admits a three-dimensional description. Subsequently, a more mathematical picture of the reduction based on foliation theory was presented in \\cite{Park:2014qoa}. In this work, we expand \\cite{Park:2014qoa} by adding another mathematical ingredient - an element of jet bundle theory - and present a more systematic and refined account thereof.
The bundles of algebraic and Dirac-Hestenes spinor fields
International Nuclear Information System (INIS)
Our main objective in this paper is to clarify the ontology of Dirac-Hestenes spinor fields (DHSF) and its relationship with even multivector fields, on a Riemann-Cartan spacetime (RCST) M=(M,g,∇,τg,↑) admitting a spin structure, and to give a mathematically rigorous derivation of the so-called Dirac-Hestenes equation (DHE) in the case where M is a Lorentzian spacetime (the general case when M is a RCST will be discussed in another publication). To this aim we introduce the Clifford bundle of multivector fields (Cl(M,g)) and the left (ClSpin1,3el(M)) and right (ClSpin1,3er(M)) spin-Clifford bundles on the spin manifold (M,g). The relation between left ideal algebraic spinor fields (LIASF) and Dirac-Hestenes spinor fields (both fields are sections of ClSpin1,3el(M)) is clarified. We study in detail the theory of covariant derivatives of Clifford fields as well as that of left and right spin-Clifford fields. A consistent Dirac equation for a DHSF Ψ is a member of sec ClSpin1,3el(M) (denoted DECll) on a Lorentzian spacetime is found. We also obtain a representation of the DECll in the Clifford bundle Cl(M,g). It is such equation that we call the DHE and it is satisfied by Clifford fields ψΞ is a member of sec Cl(M,g). This means that to each DHSF Ψ is a member of sec ClSpin1,3el(M) and spin frame Ξ is a member of sec PSpin1,3e(M), there is a well-defined sum of even multivector fields ψΞ isa member of sec Cl(M,g) (EMFS) associated with Ψ. Such an EMFS is called a representative of the DHSF on the given spin frame. And, of course, such a EMFS (the representative of the DHSF) is not a spinor field. With this crucial distinction between a DHSF and its representatives on the Clifford bundle, we provide a consistent theory for the covariant derivatives of Clifford and spinor fields of all kinds. We emphasize that the DECll and the DHE, although related, are equations of different mathematical natures. We study also the local Lorentz invariance and the
On bundles of rank 3 computing Clifford indices
Lange, H
2012-01-01
Let $C$ be a smooth irreducible projective algebraic curve defined over the complex numbers. The notion of the Clifford index of $C$ was extended a few years ago to semistable bundles of any rank. Recent work has been focussed mainly on the rank-2 Clifford index, although interesting results have also been obtained for the case of rank 3. In this paper we extend this work, obtaining improved lower bounds for the rank-3 Clifford index. This allows the first computations of the rank-3 index in non-trivial cases and examples for which the rank-3 index is greater than the rank-2 index.
Maximum allowable heat flux for a submerged horizontal tube bundle
International Nuclear Information System (INIS)
For application to industrial heating of large pools by immersed heat exchangers, the socalled maximum allowable (or open-quotes criticalclose quotes) heat flux is studied for unconfined tube bundles aligned horizontally in a pool without forced flow. In general, we are considering boiling after the pool reaches its saturation temperature rather than sub-cooled pool boiling which should occur during early stages of transient operation. A combination of literature review and simple approximate analysis has been used. To date our main conclusion is that estimates of q inch chf are highly uncertain for this configuration
The Business of Bundling: Joining Forces on Joint Replacement.
Kaldy, Joanne
2016-01-01
A mandated bundled-payment program for joint replacement is in place in several regions across the country, and practitioners such as pharmacists are still sorting out their roles in this federal initiative. To get involved, pharmacists need to establish connections with area hospitals and physician groups to promote and document their ability to manage medications, reduce and eliminate medication-related problems and rehospitalizations, and work with patients to maximize adherence and improve communication for those undergoing hip and knee replacement. PMID:26975592
Stavrou, Eleni T.; Brewster, Chris
2005-01-01
Strategic human resource management has been linked to competitive advantage and in turn to organizational performance. This linkage has been viewed from a universal, a contextual or a configurational perspective. Adopting the latter perspective, the authors of the present study investigate the possible Strategic HRM Bundles of competitive advantage within the EU and the extent to which these bundles are linked to business performance. The exploration revealed fifteen bundles: six of which ha...
Uncovery boiloff transients in a 3- x 3-rod bundle. Final report
International Nuclear Information System (INIS)
A study was carried out of transiently boiling dry a 3- x 3-rod bundle. The location of the two-phase mixture level, bundle heat transfer, and liquid inventory were measured. The effects of injecting cold water at the top of the bundle were also studied. The report documents the test data and includes a diversion of upper tie plate and counter-current flooding phenomena on core uncovery
The Hair Bundle: Fluid-Structure Interaction in the Inner Ear
Baumgart, Johannes
2010-01-01
A multitude of processes cooperate to produce the sensation of sound. The key initial step, the transformation from mechanical motion into an electrical signal, takes place in highly specialized mechanosensitive organelles that are called hair bundles due to their characteristic appearance. Each hair bundle comprises many apposed cylindrical stereocilia that are located in a liquid-filled compartment of the inner ear. The viscous liquid surrounding the hair bundle dissipates energy and dampen...
Application of artificial neural network in bundle critical heat flux prediction
International Nuclear Information System (INIS)
A bundle critical heat flux (CHF) database based on subchannel local condition is obtained by analyzing existing bundle experimental database with COBRA-IV code. Artificial neural network is then applied to train the database and a bundle CHF prediction model is finally obtained. The prediction accuracy of the obtained model is much better than that from general empiric formula, and the root-mean-square of predicated value is 5.63%. (authors)
Tanner, J; Kiernan, M; Hilliam, R; Davey, S; Collins, E; Wood, T; Ball, J; Leaper, D
2016-04-01
Introduction In 2010 a care bundle was introduced by the Department of Health (DH) to reduce surgical site infections (SSIs) in England. To date, use of the care bundle has not been evaluated despite incorporating interventions with resource implications. The aim of this study was to evaluate the DH SSI care bundle in open colorectal surgery. Methods A prospective cohort design was used at two teaching hospitals in England. The baseline group consisted of 127 consecutive patients having colorectal surgery during a 6-month period while the intervention group comprised 166 patients in the subsequent 6 months. SSI and care bundle compliance data were collected using dedicated surveillance staff. Results Just under a quarter (24%) of the patients in the baseline group developed a SSI compared with just over a quarter (28%) in the care bundle group (p>0.05). However, compliance rates with individual interventions, both before and after the implementation of the bundle, were similar. Interestingly, in only 19% of cases was there compliance with the total care bundle. The single intervention that showed an associated reduction in SSI was preoperative warming (p=0.032). Conclusions The DH care bundle did not reduce SSIs after open colorectal surgery. Despite this, it is not possible to state that the bundle is ineffective as compliance rates before and after bundle implementation were similar. All studies evaluating the effectiveness of care bundles must include data for compliance with interventions both before and after implementation of the care bundle; poor compliance may be one of the reasons for the lower than expected reduction of SSIs. PMID:26924481
Some cohomology classes in principal fiber bundles and their application to riemannian geometry.
Chern, S S; Simons, J
1971-04-01
We define some new global invariants of a fiber bundle with a connection. They are cohomology classes in the principal fiber bundle that are defined when certain characteristic curvature forms vanish. In the case of the principal tangent bundle of a riemannian manifold, they are invariant under a conformal transformation of the metric. They give necessary conditions for conformal immersion of a riemannian manifold in euclidean space. PMID:16591916
Mohammadi, Morteza; Foroutan, Masumeh
2013-02-21
In this work, the two mixtures of ionic liquid 1-n-propyl-4-amino-1,2,4-triazolium bromide and each type of the aggregated single-walled carbon nanotubes (SWCNTs), i.e. bundled SWCNTs and non-bundled, were investigated using molecular dynamics (MD) simulations. The structural characteristics of a SWCNT in the ionic liquid (IL) were examined by analyzing the radial distribution functions and the results show that the nearest IL cations to the SWCNT surface can approach it from three different positions. Also, the possibility of the dispersion of the bundled SWCNTs containing three and seven carbon nanotubes was investigated. The obtained results showed that under the investigated conditions, the IL cannot disperse the bundled SWCNTs, but it can disperse six and seven aggregated non-bundled ones. Moreover, we investigated the underlying dispersion mechanism of the aggregated SWCNTs in the IL, using MD simulations. The self diffusion coefficients and transport numbers of the cations and anions were computed in the systems containing pure IL, the mixtures of IL and one, six and seven non-bundled SWCNTs and the systems containing IL and bundled SWCNTs with three and seven carbon nanotubes. The obtained results showed that the diffusion coefficients and the transport numbers of the cations are more than anions in all mentioned systems. PMID:23318467
Post-irradiation examination of the 37M fuel bundle at Chalk River Laboratories (AECL)
Energy Technology Data Exchange (ETDEWEB)
Armstrong, J. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Daniels, T. [Ontario Power Generation, Pickering, Ontario (Canada); Montin, J. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)
2014-03-15
The modified (-element (37M) fuel bundle was designed by Ontario Power Generation (OPG) to improve Critical Heat Flux (CHF) performance in ageing pressure tubes. A modification of the conventional 37-element fuel bundle design, the 37M fuel bundle allows more coolant flow through the interior sub-channels by way of a smaller central element. A demonstration irradiation (DI) of thirty-two fuel bundles was completed in 2011 at OPG's Darlington Nuclear Generating Station to confirm the suitability of the 37M fuel bundles for full core implementation. In support of the DI, fuel elements were examined in the Chalk River Laboratories Hot Cells. Inspection activities included: Bundle and element visual examination; Bundle and element dimensional measurements; Verification of bundle and element integrity; and Internal Gas Volume Measurements. The inspection results for 37M were comparable to that of conventional 37-element CANDU fuel. Fuel performance parameters of the 37M DI fuel bundle and fuel elements were within the range observed for similarly operated conventional 37-element CANDU fuel. Based on these Post Irradiation Examination (PIE) results, 37M fuel performed satisfactorily. (author)
Numerical model for thermal and mechanical behaviour of a CANDU 37-element bundle
International Nuclear Information System (INIS)
Prediction of transient fuel bundle deformations is important for assessing the integrity of fuel and the surrounding structural components under different operating conditions including accidents. For numerical simulation of the interactions between fuel bundle and pressure tube, a reliable numerical bundle model is required to predict thermal and mechanical behaviour of the fuel bundle assembly under different thermal loading conditions. To ensure realistic representations of the bundle behaviour, this model must include all of the important thermal and mechanical features of the fuel bundle, such as temperature-dependent material properties, thermal viscoplastic deformation in sheath, fuel-to-sheath interactions, endplate constraints and contacts between fuel elements. In this paper, we present a finite element based numerical model for predicting macroscopic transient thermal-mechanical behaviour of a complete 37-element CANDU nuclear fuel bundle under accident conditions and demonstrate its potential for being used to investigate fuel bundle to pressure tube interaction in future nuclear safety analyses. This bundle model has been validated against available experimental and numerical solutions and applied to various simulations involving steady-state and transient loading conditions. (author)
Studying the vibrations of rod bundles under asymmetrical flow-round
International Nuclear Information System (INIS)
The results of experimental invesigation into vibrations of peripheral tubes in a rod bundle initiated by coolant flow are presented. Conditions of flowing around the rod bundles with different deflections in the channel geometry and hydrodynamics of coolant flow are simulated on special models. Data characterizing the dependence of the rod vibration amplitudes on the value of the gap between the bundle and the channel as well as the effect of the transverse constituent of the coolant overflow from the centre of the bundle to periphery on the rod vibration amplitude in one- and two-phase flows are obtained
Pressure drop redistribution experimental analysis in axial flow along the bundles
International Nuclear Information System (INIS)
Fuel elements of PWR type nuclear reactors are composed of rod bundles, arranged in square arrays, held by grid type spacers. The coolant flows axially along the bundle. Although such elements are laterally open, pressure drop experiments are performed in closed type test sections, originating the appearance of subchannels of different geometries. Utilizing a test section of two bundles of 4 x 4 pins and performing experiments with and without separation between the bundles, the flow redistribution factors, the friction, and the grid drag coefficients were determined for the interior subchannels. 03 refs, 06 figs, 02 tabs. (B.C.A.)
Development of an advanced LMR steam generator free from SWR with a double tube bundle configuration
International Nuclear Information System (INIS)
This paper describes the activities made at KAERI to develop an advanced LMR(Liquid Metal Reactor) steam generator which is free from SWR (Sodium Water Reaction) to resolve the concern of the SWR possibility and improve the economic feature of an LMR. The steam generator design houses two tube bundles that are functionally different and its tube bundle zone is radially or vertically divided into two regions. The SG is equipped with hot and cold fluid tube bundles, medium fluid and a pump. It prevents the occurrence of a sodium water reaction while sodium is still being used as the coolant for the primary heat transport system. The feasibility of using the SG with a double tube bundle for an actual use in a LMR plant is evaluated by setting up the skeleton of the NSSS for various possible configurations of the SG tube bundles. Analysis was made for various types of the new steam generator with a double tube bundle. Since the heat transfer in the SG is made among the three different fluids, it comes to have its unique heat transfer characteristics. The analysis showed the possibility for the occurrence of an undesirable reversed heat transfer not only in the integrated single-region bundle type but also in the integrated double-region bundle type. The performance analysis revealed practical performance characteristics for the various bundle configurations. Also the feasibility study for the various NSSS configurations with the new SG is described. (authors)
A new LMR steam generator free from SWR with a double tube bundle configuration
International Nuclear Information System (INIS)
This paper describes the activities made at KAERI to develop an advanced liquid metal reactor (LMR) steam generator which is free from a sodium water reaction (SWR) to resolve the concern of the SWR possibility and improve the economic features of the LMR. The steam generator design houses two tube bundles that are functionally different and its tube bundle region is radially or vertically divided into two. The SG is equipped with hot and cold fluid tube bundles, a medium fluid and a pump. It prevents the occurrence of the sodium water reaction while sodium is still used as the coolant for the primary heat transport system. The feasibility of using the SG with a double tube bundle for an actual use in a LMR plant is evaluated by setting up the skeleton of the NSSS for various possible configurations of the SG tube bundles. Analysis was made for various types of the new steam generator with a double tube bundle. Since the heat transfer in the SG is made among three different fluids, it has unique heat transfer characteristics. The analysis showed the possibility of the occurrence of an undesirable reversed heat transfer not only in the integrated single-region bundle type but also in the integrated double-region bundle type. The performance analysis revealed practical performance characteristics for the various bundle configurations. Also the feasibility study for the various NSSS configurations with the new SG is described
Padilla-Gamiño, J. L.; Weatherby, T. M.; Waller, R. G.; Gates, R. D.
2011-06-01
The majority of scleractinian corals are hermaphrodites that broadcast spawn their gametes separately or packaged as egg-sperm bundles during spawning events that are timed to the lunar cycle. The egg-sperm bundle is an efficient way of transporting gametes to the ocean surface where fertilization takes place, while minimizing sperm dilution and maximizing the opportunity for gamete encounters during a spawning event. To date, there are few studies that focus on the formation and structure of egg-sperm bundle. This study explores formation, ultrastructure, and longevity of the egg-sperm bundle in Montipora capitata, a major reef building coral in Hawai`i. Our results show that the egg-sperm bundle is formed by a mucus layer secreted by the oocytes. The sperm package is located at the center of each bundle, possibly reflecting the development of male and female gametes in different mesenteries. Once the egg-sperm bundle has reached the ocean surface, it breaks open within 10-35 min, depending on the environmental conditions (i.e., wind, water turbulence). Although the bundle has an ephemeral life span, the formation of an egg-sperm bundle is a fundamental part of the reproductive process that could be strongly influenced by climate change and deterioration of water quality (due to anthropogenic effects) and thus requires further investigation.
The value of the abnormalities of bronchovascular bundles in the diagnosis of diffused lung diseases
International Nuclear Information System (INIS)
To evaluate the abnormalities of bronchovascular bundles in the differential diagnosis of the diffuse lung disease, seventy-two patients with diffuse lung diseases were evaluated, 15 of 72 patients were pathologically proven and the others clinically proven. Of these 72 patients, there were 33 patients with diffuse pulmonary interstitial disease, 5 patients with pulmonary parenchymal disease, 14 patients with bronchial disease, and 20 patients with disseminated disease. All patients had conventional CT scan of the chest, some also had HRCT scan. All CT images were jointly reviewed by two radiologists. The features of the abnormalities of bronchovascular bundles included: (1) Thinning of bronchovascular bundles, predominantly seen in diffuse interstitial disease of lung and chronic bronchitis; (2) thickening of bronchovascular bundles, predominantly seen in interstitial diseases and disseminated lung diseases such as sarcoidosis and lymphangitis carcinomatosis with beaded appearance of bronchovascular bundles; (3) Increased visibility of bronchovascular bundles, predominantly seen in bronchiolitis and disseminated lung diseases. CT features of the abnormalities of bronchovascular bundles are present in 80% of diffuse lung diseases. The features are not specific, but the beaded bronchovascular bundles are always seen in sarcoidosis and lymphangitis carcinomatosis. In making a distinction between idiopathic pulmonary fibrosis and chronic bronchitis complicated with interstitial fibrosis, the position of diaphragm is of value in differential diagnosis, normal or elevated diaphragm is usually seen in the former, while low and flattened diaphragm in the latter. Change of the appearance of bronchovascular bundles from normality to abnormality reflects the process of development of the lung disease
A Mathematical Base for Fibre Bundle Formulation of Lagrangian Quantum Field Theory
International Nuclear Information System (INIS)
The paper contains a differential-geometric foundations for an attempt to formulate Lagrangian (canonical) quantum field theory on fibre bundles. In it the standard Hilbert space of quantum field theory is replace with a Hilbert bundle; the former playing a role of a (typical) fibre of the letter one. Suitable sections of that bundle replace the ordinary state vectors and the operators on the system's Hilbert space are transformed into morphisms of the same bundle. In particular, the field operators are mapped into corresponding field morphisms.
Hydraulic reinforcement of channel at lower tie-plate in BWR fuel bundle
International Nuclear Information System (INIS)
This patent describes an apparatus in a fuel bundle for confining fuel rods for the generation of steam in a steam water mixture passing interior of the fuel bundle. The fuel bundle includes: a lower tie-plate for supporting the fuel rods and permitting flow from the lower exterior portion of the fuel bundle into the interior portion of the fuel bundle; a plurality of fuel rods. The fuel rods supported on the lower tie-plate extending upwardly to and towards the upper portion of the fuel bundle for the generation of steam in a passing steam and water mixture interior of the fuel bundle; an upper tie-plate for maintaining the fuel rods in side-by-side relation and permitting a threaded connection between a plurality of the fuel rods with the threaded connection being at the upper and lower tie-plate. The upper tie-plate permitting escape of a steam water mixture from the top of the fuel bundle; a fuel bundle channel; and a labyrinth seal configured in the lower tie-plate
Redesign and replacement of Connecticut Yankee moisture separator/reheater (MSR) tube bundles
International Nuclear Information System (INIS)
This paper describes the various aspects of the tube bundle redesign and replacement coordinated by Northeast Utilities Service Company for the Connecticut Yankee Atomic Power Company during the plant's 1980 refueling outage. The main objective of the replacement was to improve the operating reliability along with secondary plant chemistry through the use of new bundle design and tube material. The considerations leading to the selection of material and design of the new bundles, the highlights of fabrication and bundle change-out, and the eddy current test experience and performance monitoring techniques and results are presented. 6 refs
Overview of methods to increase dryout power in CANDU fuel bundles
Energy Technology Data Exchange (ETDEWEB)
Groeneveld, D.C., E-mail: degroeneveld@gmail.com [Chalk River Laboratories, AECL, Chalk River (Canada); University of Ottawa, Department of Mechanical Engineering, Ottawa (Canada); Leung, L.K.H. [Chalk River Laboratories, AECL, Chalk River (Canada); Park, J.H. [Korean Atomic Energy Research Institute, Daejeon (Korea, Republic of)
2015-06-15
Highlights: • Small changes in bundle geometry can have noticeable effects on the bundle CHF. • Rod spacing devices can results in increases of over 200% in CHF. • CHF enhancement decays exponentially downstream from spacers. • CHF-enhancing bundle appendages also increase the post-CHF heat transfer. - Abstract: In CANDU reactors some degradation in the CCP (critical channel power, or power corresponding to the first occurrence of CHF in any fuel channel) will occur with time because of ageing effects such as pressure-tube diametral creep, increase in reactor inlet-header temperature, increased hydraulic resistance of feeders. To compensate for the ageing effects, various options for recovering the loss in CCP are described in this paper. They include: (i) increasing the bundle heated perimeter, (ii) optimizing the bundle configuration, (iii) optimizing core flow and flux distribution, (iv) reducing the bundle hydraulic resistance, (v) use of CHF-enhancing bundle appendages, (vi) more precise experimentation, and (vii) redefining CHF. The increase in CHF power has been quantified based on experiments on full-scale bundles and subchannel code predictions. The application of several of these CHF enhancement principles has been used in the development of the 43-rod CANFLEX bundle.
International Nuclear Information System (INIS)
Natural convection heat transfer from horizontal rod bundles in Nxm×Nym arrays (Nxm, Nym = 5–9) in liquid sodium was numerically analyzed for three types of the bundle geometry (in-line rows, staggered rows I and II). The unsteady laminar two-dimensional basic equations for natural convection heat transfer caused by a step heat flux were numerically solved until the solution reaches a steady state. The PHOENICS code was used for the calculation considering the temperature dependence of thermophysical properties concerned. The surface heat fluxes for each cylinder were equally given for a modified Rayleigh number, Rf, ranging from 0.0637 to 63.1 (q = 1×104 to 7×106 W/m2). Sx/D and Sy/D for the rod bundle, which are the ratios of the distance between center axes on the abscissa and the ordinate to the rod diameter, respectively, were ranged from 1.6 to 2.5 on each bundle geometry. The spatial distribution of Nusselt numbers, Nu, on horizontal rods of a bundle was clarified. The average value of Nusselt number, Nuav, for three types of bundle geometry with various values of Sx/D and Sy/D were calculated to examine the effect of the array size, S/D and Rf on heat transfer. The bundle geometry for the higher Nuav value under the condition of Sx/D×Sy/D = 4 was examined by changing the ratio of Sx/Sy. A correlation for Nuav for the three types of bundle geometry above mentioned including the effects of Sx/D and Sy/D was developed. The correlation can describe the theoretical values of Nuav for the three types of bundle geometry in Nxm×Nym arrays (Nxm, Nym = 5–9) for Sx/D and Sy/D ranging from 1.6 to 2.5 within 10% difference. (author)
N=2 Heterotic-Type II duality and bundle moduli
Alexandrov, Sergei; Pioline, Boris; Valandro, Roberto
2014-01-01
Heterotic string compactifications on a $K3$ surface $\\mathfrak{S}$ depend on a choice of hyperk\\"ahler metric, anti-self-dual gauge connection and Kalb-Ramond flux, parametrized by hypermultiplet scalars. The metric on hypermultiplet moduli space is in principle computable within the $(0,2)$ superconformal field theory on the heterotic string worldsheet, although little is known about it in practice. Using duality with type II strings compactified on a Calabi-Yau threefold, we predict the form of the quaternion-K\\"ahler metric on hypermultiplet moduli space when $\\mathfrak{S}$ is elliptically fibered, in the limit of a large fiber and even larger base. The result is in general agreement with expectations from Kaluza-Klein reduction, in particular the metric has a two-stage fibration structure, where the $B$-field moduli are fibered over bundle and metric moduli, while bundle moduli are themselves fibered over metric moduli. A more precise match must await a detailed analysis of $R^2$-corrected ten-dimensiona...
Motor-free actin bundle contractility driven by molecular crowding
Schnauß, Jörg; Schuldt, Carsten; Schmidt, B U Sebastian; Glaser, Martin; Strehle, Dan; Heussinger, Claus; Käs, Josef A
2015-01-01
Modeling approaches of suspended, rod-like particles and recent experimental data have shown that depletion forces display different signatures depending on the orientation of these particles. It has been shown that axial attraction of two rods yields contractile forces of 0.1pN that are independent of the relative axial shift of the two rods. Here, we measured depletion-caused interactions of actin bundles extending the phase space of single pairs of rods to a multi-particle system. In contrast to a filament pair, we found forces up to 3pN . Upon bundle relaxation forces decayed exponentially with a mean decay time of 3.4s . These different dynamics are explained within the frame of a mathematical model by taking pairwise interactions to a multi-filament scale. The macromolecular content employed for our experiments is well below the crowding of cells. Thus, we propose that arising forces can contribute to biological force generation without the need to convert chemical energy into mechanical work.
Mixed connectivity of Cartesian graph products and bundles
Erves, Rija
2010-01-01
Mixed connectivity is a generalization of vertex and edge connectivity. A graph is $(p,0)$-connected, $p>0$, if the graph remains connected after removal of any $p-1$ vertices. A graph is $(p,q)$-connected, $p\\geq 0$, $q>0$, if it remains connected after removal of any $p$ vertices and any $q-1$ edges. Cartesian graph bundles are graphs that generalize both covering graphs and Cartesian graph products. It is shown that if graph $F$ is $(p_{F},q_{F})$-connected and graph $B$ is $(p_{B},q_{B})$-connected, then Cartesian graph bundle $G$ with fibre $F$ over the base graph $B$ is $(p_{F}+p_{B},q_{F}+q_{B})$-connected. Furthermore, if $q_{F},q_{B}>0$, then $G$ is also $(p_{F}+p_{B}+1,q_{F}+q_{B}-1)$-connected. Finally, let graphs $G_i, i=1,...,n,$ be $(p_i,q_i)$-connected and let $k$ be the number of graphs with $q_i>0$. The Cartesian graph product $G=G_1\\Box G_2\\Box ... \\Box G_n$ is $(\\sum p_i,\\sum q_i)$-connected, and, for $ k\\geq 1$, it is also $(\\sum p_i+k-1,\\sum q_i-k+1)$-connected.
A four-helix bundle stores copper for methane oxidation.
Vita, Nicolas; Platsaki, Semeli; Baslé, Arnaud; Allen, Stephen J; Paterson, Neil G; Crombie, Andrew T; Murrell, J Colin; Waldron, Kevin J; Dennison, Christopher
2015-09-01
Methane-oxidizing bacteria (methanotrophs) require large quantities of copper for the membrane-bound (particulate) methane monooxygenase. Certain methanotrophs are also able to switch to using the iron-containing soluble methane monooxygenase to catalyse methane oxidation, with this switchover regulated by copper. Methane monooxygenases are nature's primary biological mechanism for suppressing atmospheric levels of methane, a potent greenhouse gas. Furthermore, methanotrophs and methane monooxygenases have enormous potential in bioremediation and for biotransformations producing bulk and fine chemicals, and in bioenergy, particularly considering increased methane availability from renewable sources and hydraulic fracturing of shale rock. Here we discover and characterize a novel copper storage protein (Csp1) from the methanotroph Methylosinus trichosporium OB3b that is exported from the cytosol, and stores copper for particulate methane monooxygenase. Csp1 is a tetramer of four-helix bundles with each monomer binding up to 13 Cu(I) ions in a previously unseen manner via mainly Cys residues that point into the core of the bundle. Csp1 is the first example of a protein that stores a metal within an established protein-folding motif. This work provides a detailed insight into how methanotrophs accumulate copper for the oxidation of methane. Understanding this process is essential if the wide-ranging biotechnological applications of methanotrophs are to be realized. Cytosolic homologues of Csp1 are present in diverse bacteria, thus challenging the dogma that such organisms do not use copper in this location. PMID:26308900
Cortactin Adopts a Globular Conformation and Bundles Actin into Sheets
Energy Technology Data Exchange (ETDEWEB)
Cowieson, Nathan P.; King, Gordon; Cookson, David; Ross, Ian; Huber, Thomas; Hume, David A.; Kobe, Bostjan; Martin, Jennifer L. (Queensland); (Aust. Synch.)
2008-08-21
Cortactin is a filamentous actin-binding protein that plays a pivotal role in translating environmental signals into coordinated rearrangement of the cytoskeleton. The dynamic reorganization of actin in the cytoskeleton drives processes including changes in cell morphology, cell migration, and phagocytosis. In general, structural proteins of the cytoskeleton bind in the N-terminal region of cortactin and regulatory proteins in the C-terminal region. Previous structural studies have reported an extended conformation for cortactin. It is therefore unclear how cortactin facilitates cross-talk between structural proteins and their regulators. In the study presented here, circular dichroism, chemical cross-linking, and small angle x-ray scattering are used to demonstrate that cortactin adopts a globular conformation, thereby bringing distant parts of the molecule into close proximity. In addition, the actin bundling activity of cortactin is characterized, showing that fully polymerized actin filaments are bundled into sheet-like structures. We present a low resolution structure that suggests how the various domains of cortactin interact to coordinate its array of binding partners at sites of actin branching.
CFD and DNS methodologies development for fuel bundle simulations
International Nuclear Information System (INIS)
Development and application of Computational Fluid Dynamics (CFD) and Direct Numerical Simulation (DNS) approaches to the simulation of coolant flow inside nuclear fuel bundles are presented, focusing on the advantages and limitations of the different methodologies and on their synergetic potential. High Reynolds number flow cases are analyzed with the adoption of an improved anisotropic turbulence modeling, which adopts a non-linear stress strain correlation and an improved near wall treatment. The capability of the model of predicting the coolant flow distribution inside the bundles is shown and discussed on the base of comparison with experimental data for a variety of geometrical and Reynolds number conditions. In particular wall shear stresses, velocity, and secondary flow distributions comparisons are shown. Moreover, DNS computations are performed adopting an algorithm based on the finite difference method, extended to boundary fitted coordinate systems in order to efficiently concentrate grids near the distorted wall boundaries. The validity and significance of the results is discussed underlying the importance of the insights into the turbulence structure. The calculations are further extended to higher Reynolds numbers, which cannot in general be treated with DNS approach, renouncing to the estimation of the higher-order moments, but limited to the evaluation of the averaged velocity profiles, turbulence intensities and Reynolds stresses. (authors)
Damping in heat exchanger tube bundles. A review
International Nuclear Information System (INIS)
Damping is a major concern in the design and operation of tube bundles with loosely supported tubes in baffles for process shell and tube heat exchangers and steam generators which are used in nuclear, process and power generation industries. System damping has a strong influence on the amplitude of vibration. Damping depends upon the mechanical properties of the tube material, geometry of intermediate supports and the physical properties of shell-side fluid. Type of tube motion, number of supports, tube frequency, vibration amplitude, tube mass or diameter, side loads, support thickness, higher modes, shell-side temperature etc., affect damping in tube bundles. The importance of damping is further highlighted due to current trend of larger exchangers with increased shell-side velocities in modern units. Various damping mechanisms have been identified (Friction damping, Viscous damping, Squeeze film damping, Support damping. Two-Phase damping, and very recent-Thermal damping), which affect the performance of process exchangers and steam generators with respect to flow induced vibration design, including standard design guidelines. Damping in two-phase flow is very complex and highly void fraction, and flow-regime dependent. The current paper focuses on the various known damping mechanisms subjected to both single and two-phase cross-flow in process heat exchangers and steam generators and formulates the design guidelines for safer design. (author)
Dislodgement of carbon nanotube bundles under pressure driven flow.
Baowan, Duangkamon; Cox, Barry J; Hill, James M
2010-04-16
Experimental and predicted flow rates through carbon nanotubes vary considerably but generally are reported to be well in excess of that predicted by the conventional Poiseuille flow, and therefore nanotubes embedded in a matrix might provide membranes with exceptional mass transport properties. In this paper, applied mathematical modelling is undertaken to estimate the three forces acting on a nanotube bundle, namely the molecular interaction force, the viscous force, and the static pressure force. In deducing estimates of these forces we introduce a modification of the notion of the effective dead area for a carbon nanotube membrane, and we calculate the total forces necessary to push one or more of the nanotubes out of the bundle, thus creating a channel through which further enhancement of flow may take place. However, careful analysis shows that the nett dislodgement force is entirely independent on the useable flow area, but rather depends only on the total cross-sectional area perpendicular to the flow. This rather surprising result is a consequence of the flow being steady and a balance of the viscous and pressure forces. PMID:20332554
Optimal Nonlinear Pricing, Bundling Commodities and Contingent Services
International Nuclear Information System (INIS)
In this paper, we propose to analyze optimal nonlinear pricing when a firm offers in a bundle a commodity and a contingent service. The paper studies a mechanism design where all private information can be captured in a single scalar variable in a monopoly context. We show that to propose the package for commodity and service is less costly for the consumer, the firm has lower consumers' rent than the situation where it sells their good and contingent service under an independent pricing strategy. In fact, the possibility to use price discrimination via the supply of package is dominated by the fact that it is costly for the consumer to sign two contracts. Bundling energy and a contingent service is a profitable strategy for a energetician monopoly practising optimal nonlinear tariff. We show that the rates of the energy and the contingent service depend to the optional character of the contingent service and depend to the degree of complementarity between commodities and services. (authors)
An assessment of thermal behavior of the DUPIC fuel bundle by subchannel analysis
International Nuclear Information System (INIS)
Thermal behavior of the standard DUPIC fuel has been assessed. The DUPIC fuel bundle has been modeled for a subchannel analysis using the ASSERT-IV code which was developed by AECL. From the calculated mixture enthalpy, equilibrium quality and void fraction distributions of the DUPIC fuel bundle, it is found that net buoyancy effect is pronounced in the central region of the DUPIC fuel bundle when compared with the standard CANDU fuel bundle. It is also found that the central region of the DUPIC fuel bundle can be cooled more efficiently than that of the standard fuel bundle. Based upon the subchannel modeling used in this study, the location of minimum CHFR in the DUPIC fuel bundle has been found to be very similar to that of the standard fuel. From the calculated mixture enthalpy distribution at the exit of the fuel channel, it is found that the mixture enthalpy and void fraction can be highest in the peripheral region of the DUPIC fuel bundle. On the other hand, the enthalpy and the void fraction was found to be highest in the central region of the standard CANDU fuel bundle at the exit of the fuel channel. Since the transverse interchange model between subchannels is important for the behavior of these variables, it is needed to put more effort in validating the transverse interchange model. For the purpose of investigating influence of thermal-hydraulic parameter variations of the DUPIC fuel bundle, four different values of the channel flow rates were used in the subchannel analysis. The effect of the channel flow reduction on thermal-hydraulic parameters have been presented. This study shows that the subchannel analysis is very useful in assessing thermal behavior of the fuel bundles in CANDU reactors. (author). 12 refs., 3 tabs., 17 figs
Relationships between the Tensile Properties and Tenacity extension Behaviour of Fibre-bundles
Institute of Scientific and Technical Information of China (English)
YU Wei-dong
2002-01-01
Fibre bundle testing is different from single-fibre measurement, not only in testing methods and instruments, but in the results obtained. For wool fibres, Sirolan-TENSOR can supply fibre-bundle tenacity (BS) and bundle extension (BE), but has some limitations on the analysis of the measured tensile curves of fibre bundles. It has not only raised new parameters,such as initial modulus (BM) and specific work of rupture (BW), as well as the specific work before or after the peak-point(WBP or WAP) and the ratios of WAP/WBP and WAP/BW, but also compared the tensile behaviour of different fibre-bundles, e.g. wool,polyester and viscose rayon fibre- bundles. The experimental results from 32 lots of wool tops show that there are correlations between bundle tensile properties,such as BS-BE, BS-BM, BS-BW, BE-BW and BM-BW.However, the variables of coefficients of variance (CV)are almost independent of each other and have no correlation with the average values of fibre bundle tensile parameters, except for BS-CVBM and CVBM-BW.
Cohomology of line bundles on the flag variety for type G_2
DEFF Research Database (Denmark)
Andersen, Henning Haahr; Kaneda, Masaharu
2012-01-01
In the case of a simple algebraic group G of type G2 over a field of characteristic p>0 we study the cohomology modules of line bundles on the flag variety for G. Our main result is a complete determination of the vanishing behavior of such cohomology in the case where the line bundles in question...
GPU acceleration of the stochastic grid bundling method for early-exercise options
Leitao Rodriguez, A.; Oosterlee, C.W.
2015-01-01
In this work, a parallel graphics processing units (GPU) version of the Monte Carlo stochastic grid bundling method (SGBM) for pricing multi-dimensional early-exercise options is presented. To extend the method’s applicability, the problem dimensions and the number of bundles will be increased drast
Parabolic Bundles on Algebraic Surfaces I -- The Donaldson-Uhlenbeck Compactification
Indian Academy of Sciences (India)
V Balaji; A Dey; R Parthasarathi
2008-02-01
The aim of this paper is to construct the parabolic version of the Donaldson-Uhlenbeck compactification for the moduli space of parabolic stable bundles on an algebraic surface with parabolic structures along a divisor with normal crossing singularities. We prove the non-emptiness of the moduli space of parabolic stable bundles of rank 2.
Modification of the Simpson moduli space M_{3m+1}(P_2) by vector bundles (I)
Iena, Oleksandr
2010-01-01
We consider the moduli space of stable vector bundles on curves embedded in P_2 with Hilbert polynomial 3m+1 and construct a compactification of this space by vector bundles. The result is a blow up of the Simpson moduli space M_{3m+1}(P_2).
Demonstrating the compatibility of Canflex fuel bundles with a CANDU 6 fuelling machine
International Nuclear Information System (INIS)
CANFLEX is a new 43-element fuel bundle, designed for high operating margins. It has many small-diameter elements in its two outer rings, and large-diameter elements in its centre rings. By this means, the linear heat ratings are lower than those of standard 37-element bundles for similar power outputs. A necessary part of the out-reactor qualification program for the CANFLEX fuel bundle design, is a demonstration of the bundle's compatibility with the mechanical components in a CANDU 6 Fuelling Machine (FM) under typical conditions of pressure, flow and temperature. The diameter of the CANFLEX bundle is the same as that of a 37-element bundle, but the smaller-diameter elements in the outer ring result in a slightly larger end-plate diameter. Therefore, to minimize any risk of unanticipated damage to the CANDU 6 FM sidestops, a series of measurements and static laboratory tests were undertaken prior to the fuelling machine tests. The tests and measurements showed that; a) the CANFLEX bundle end plate is compatible with the FM sidestops, b) all the dimensions of the CANFLEX fuel bundle are within the specified limits. (author). 3 tabs., 3 figs
Splitting of low rank ACM bundles on hypersurfaces of high dimension
Tripathi, Amit
2013-01-01
Let $X$ be a smooth projective hypersurface. In this note we show that any rank 3 arithmetically Cohen-Macaulay vector bundle over $X$ splits when dim $X \\geq 7$. We also find a splitting criterion for rank 4 arithmetically Cohen-Macaulay vector bundles on $X$ when dim $X \\geq 9$.
Hermitian-Einstein metrics on holomorphic vector bundles over Hermitian manifolds
International Nuclear Information System (INIS)
In this paper, we prove the long-time existence of the Hermitian-Einstein flow on a holomorphic vector bundle over a compact Hermitian (non-kaehler) manifold, and solve the Dirichlet problem for the Hermitian-Einstein equations. We also prove the existence of Hermitian-Einstein metrics for holomorphic vector bundles on a class of complete noncompact Hermitian manifolds. (author)
Cortes, Viviana
2013-01-01
This article presents a group of lexical bundles identified in a corpus of research article introductions as the first step in the analysis of these expressions in the different sections of the research article. A one-million word corpus of research article introductions from various disciplines was compiled and the lexical bundles identified in…
Harmonic sections of Riemannian vector bundles, and metrics of Cheeger-Gromoll type
Benyounes, M.; Loubeau, E.; Wood, C.M., Bucking, C., Fitzpatrick, J., & Nadella, S.R.
2006-01-01
We study harmonic sections of a Riemannian vector bundle whose total space is equipped with a 2-parameter family of metrics which includes both the Sasaki and Cheeger-Gromoll metrics. This enables the theory of harmonic unit sections to be extended to bundles with non-zero Euler class.
A Variant of K-Theory and Topological T-Duality for Real Circle Bundles
Gomi, Kiyonori
2015-03-01
For a space with involutive action, there is a variant of K-theory. Motivated by T-duality in type II orbifold string theory, we establish that a twisted version of the variant enjoys a topological T-duality for Real circle bundles, i.e., circle bundles with real structure.
Overview of flowline bundle technology from concept selection to offshore installation
Institute of Scientific and Technical Information of China (English)
Song Ruxin; Xia Qiuling
2013-01-01
Flowline bundle system consisting of carrier pipe,sleeve pipe and internal flowlines offers innovative solution for the infield transportation of oil and gas.Due to its features,flowline bundle offers a couple of advantages over conventional flowline in particular for cases where multi-flowlines and high thermal performance is of great interest.The main benefits and advantages of such system include excellent thermal performance to prevent wax formation and hydrates,multiple bundled flowlines,mechanical and corrosion protection,potential reuse,etc.With the developments of offshore oil and gas industries,more and more hydrocarbon resources are being explored and discovered from shallow to deep water.Pipeline bundle system can be a smart solution for certain applications,which can be safe and cost effective solution.The objective of this paper is to overview pipeline bundle technology,outline detailed engineering design issue and procedure.Focus is given to its potential application in offshore for infield transportation.Engineering design principles and procedures for pipeline bundle system are highlighted.Construction methods of flowline bundle onshore are reviewed.Offshore towing and installation of pipeline bundle procedure is outlined.
Institute of Scientific and Technical Information of China (English)
YU Wei-dong; Ron Postle; YANG Shou-ren; YAN Hao-jing
2002-01-01
The testing conditions of a fibre bundle tensile tester (TENSOR) are elongation speed (ES), gauge length (GL), pretension, jaw pressure, environmental temperature and relative humidity, instrument linearity and sensitivity. The effects on fibre-bundle tensile properties at different GL and ES have been discussed in detail and compared with Peirce's theories on the weaklinks and the breaking time effect. The experimental results indicate that the tensile properties of fibre bundles are strongly affected by GL and vary with different GL. The reasonable GL should be 5-15mm rather than 3.2mm for wool bundle measurements. The ES ranging from 20mm/min to 40mm/min is beneficial for obtaining comparatively stable and accurate tensile values, whereas 20 mm/min used in current testing for wool fibre bundles is at the lower limit of the suggested range. For bundle modulus measurement, the sampling interval must be selected appropriately. The new calculation of the sampling interval has been established.
International Nuclear Information System (INIS)
The nondimensional parameters of fluid-elastic vibration of tube bundle were derived and the effective method for vibration countermeasure of damage of tube bundle in the cross flow was investigated. It was explained that an application to the fluid-elastic vibration of cross-shaped tube bundle in the lower plenum structure of the future BWR reactor developed. Three nondimensional parameters such as mass attenuation parameter, nondimensional flow velocity and Reynolds number controlled the limiting flow velocity generating fluid-elastic vibrations of tube bundle in cross flow. The effect of mass attenuation parameter to the nondimensional limiting flow velocity is small when the value is smaller than 1. The effect of Reynolds number may be small when the exfoliation point does not change. It was thought two effective countermeasures of fluid-elastic vibrations: 1) the bundle tubes were tied up in a bundle not to vibrate with phase difference among tubes and 2) the real limiting flow velocity was increased at the same nondimensional limiting flow velocity by increasing the eigenfrequency. (S.Y.)
Characteristics of liquid and boiling sodium flows in heating pin bundles
International Nuclear Information System (INIS)
This study is related to cooling accidents which could occur in sodium cooled fast reactors. Thermo-hydraulic aspects of boiling experiments in pin bundles with helical wire-wrap spacer systems, in the case of undamaged geometries, are analyzed. Differences and analogies in the behavior of multi-rod bundle flows and one-dimensional channel flows are studied. A boiling model is developed for bundle geometries, and predictions obtained with the FLICA code using this models are presented. These predictions are compared with experimental results obtained in a water 19-rod bundle. Then, results of sodium boiling experiments through a 19-rod bundle are interpreted. Both cases of high power and reduced power are envisaged
Single and two-phase flow pressure drop for CANFLEX bundle
Energy Technology Data Exchange (ETDEWEB)
Park, Joo Hwan; Jun, Ji Su; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of); Dimmick, G. R.; Bullock, D. E. [Atomic Energy of Canada Limited, Ontario (Canada)
1998-12-31
Friction factor and two-phase flow frictional multiplier for a CANFLEX bundle are newly developed and presented in this paper. CANFLEX as a 43-element fuel bundle has been developed jointly by AECL/KAERI to provide greater operational flexibility for CANDU reactor operators and designers. Friction factor and two-phase flow frictional multiplier have been developed by using the experimental data of pressure drops obtained from two series of Freon-134a (R-134a) CHF tests with a string of simulated CANFLEX bundles in a single phase and a two-phase flow conditions. The friction factor for a CANFLEX bundle is found to be about 20% higher than that of Blasius for a smooth circular pipe. The pressure drop predicted by using the new correlations of friction factor and two-phase frictional multiplier are well agreed with the experimental pressure drop data of CANFLEX bundle within {+-} 5% error. 11 refs., 5 figs. (Author)
Loop-Corrected Compactifications of the Heterotic String with Line Bundles
Blumenhagen, R; Weigand, T; Blumenhagen, Ralph; Honecker, Gabriele; Weigand, Timo
2005-01-01
We consider the E8 x E8 heterotic string theory compactified on Calabi-Yau manifolds with bundles containing abelian factors in their structure group. Generic low energy consequences such as the generalised Green-Schwarz mechanism for the multiple anomalous abelian gauge groups are studied. We also compute the holomorphic gauge couplings and induced Fayet-Iliopoulos terms up to one-loop order, where the latter are interpreted as stringy one-loop corrections to the Donaldson-Uhlenbeck-Yau condition. Such models generically have frozen combinations of Kaehler and dilaton moduli. We study concrete bundles with structure group SU(N) x U(1)^M yielding quasi-realistic gauge groups with chiral matter given by certain bundle cohomology classes. We also provide a number of explicit tadpole free examples of bundles defined by exact sequences of sums of line bundles over complete intersection Calabi-Yau spaces. This includes one example with precisely the Standard Model gauge symmetry.
Defects in crystalline packings of twisted filament bundles. II. Dislocations and grain boundaries.
Azadi, Amir; Grason, Gregory M
2012-03-01
Twisted and ropelike assemblies of filamentous molecules are common and vital structural elements in cells and tissues of living organisms. We study the intrinsic frustration occurring in these materials between the two-dimensional organization of filaments in cross section and out-of-plane interfilament twist in bundles. Using nonlinear continuum elasticity theory of columnar materials, we study the favorable coupling of twist-induced stresses to the presence of edge dislocations in the lattice packing of bundles, which leads to a restructuring of the ground-state order of these materials at intermediate twist. The stability of dislocations increases as both the degree of twist and lateral bundle size grow. We show that in ground states of large bundles, multiple dislocations pile up into linear arrays, radial grain boundaries, whose number and length grows with bundle twist, giving rise to a rich class of "polycrystalline" packings. PMID:22587105
Asymmetric dynamics of ion channel forming proteins - Hepatitis C virus (HCV) p7 bundles.
Kalita, Monoj Mon; Fischer, Wolfgang B
2016-07-01
Protein p7 of hepatitis C virus (HCV) is a short 63 amino acid membrane protein which homo-oligomerises in the lipid membrane to form ion and proton conducting bundles. Two different genotypes (GTs) of p7, 1a and 5a, are used to simulate hexameric bundles of the protein embedded in a fully hydrated lipid bilayer during 400ns molecular dynamics (MD) simulations. Whilst the bundle of GT 1a is based on a fully computational derived structure, the bundle of GT 5a is based on NMR spectroscopic data. Results of a full correlation analysis (FCA) reveal that albeit structural differences both bundles screen local minima during the simulation. The collective motion of the protein domains is asymmetric. No 'breathing-mode'-like dynamics is observed. The presence of divalent ions, such as Ca-ions affects the dynamics of especially solvent exposed parts of the protein, but leaves the asymmetric domain motion unaffected. PMID:27079148
Assessing the impact of the 37M fuel bundle design on fuel safety parameters
International Nuclear Information System (INIS)
To improve the critical heat flux and margin to fuel dryout in aging CANDU nuclear generating stations, the 37-element bundle design '37R' fuel) has been modified by reducing the central fuel element diameter, producing the modified '37M' fuel bundle. The codes FACTARSS, ELESTRES, ELOCA-IST, and SOURCE have been used to compare fuel temperature, fission gas release, and element integrity in 37R and 37M fuel bundles for Bruce Power nuclear reactors. The assessment demonstrated that, relative to 37R fuel bundles, using 37M fuel bundles does not significantly impact the existing safety margins associated with fuel temperature, fission gas release, and element integrity during design basis accidents. (author)
Photoacoustic imaging by using a bundle of thin hollow-optical fibers
Seki, A.; Iwai, K.; Katagiri, T.; Matsuura, Y.
2016-03-01
We propose a photoacoustic imaging system composed of a flexible bundle of thin hollow-optical fibers that enables endoscopic diagnosis. The hollow-fiber bundle involves 37 fibers with an inner diameter of 100 μm and the total diameter of the bundle is 1.2 mm. A laser beam for photoacoustic excitation is scanned at the input end of fiber bundle and therefore, no scanning mechanism is necessary at the distal end. In addition, owing to the small numerical aperture of hollow optical fibers, a high resolution image is obtained without using a micro-lens array at the end. By using the fiber bundle probe, photoacoustic imaging of blood vessels in the ovarian membrane of fish were successfully obtained with a laser fluence of around 2.8 mJ/cm2.
Cobra-TF simulation of BWR bundle dry out experiments
International Nuclear Information System (INIS)
The COBRA-TF computer code uses a two-fluid, three-field and three-dimensional formulation to model a two-phase flow field in a specific geometry. The liquid phase is divided in a continuous liquid field and a separate dispersed field, which is used to describe the entrained liquid drops. For each space dimension, the code solves three momentum equations, three mass conservation equations and two energy conservation equations. Entrainment and depositions models are implemented into the code to model the mass transfer between the two liquid fields. This study presents the results obtained with COBRA-TF for the simulation of the Siemens 9-9Q BWR Bundle Dryout experiments. The model includes 20 channels and 34 axial nodes in the heated section. The predicted critical power and dryout location is compared with the measured values. An assessment of the code entrainment and de-entrainment models is presented. (authors)
The electrochemical properties of bundles of single-walled nanotubes
Energy Technology Data Exchange (ETDEWEB)
Zawodzinski, T.A. Jr.; Haridoss, P.; Uribe, F.A.
1998-12-31
This is the final report of a Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The authors studied electrochemical properties of single-walled fullerene nanotube bundles. The materials exhibited a highly anisotropic conductivity. Electrochemical cycling in solutions of alkyl ammonium salts in propylene carbonate revealed that the nanotubes are stable to at least {+-}1.5 V and have a fairly high accessible surface area. Double-layer charging currents of approximately 30 farads per gram were observed. This is on the same order of magnitude, though somewhat lower, than state-of-the-art values for ultra-capacitor materials. Electrochemical insertion of lithium was attempted. Though several features were observed in a slow cyclic voltammetric scan, these features were not reversible, indicating little reversible insertion. Several possible reasons for this behavior are discussed.
Ion-irradiation-induced defects in bundles of carbon nanotubes
Salonen, E; Nordlund, K
2002-01-01
We study the structure and formation yields of atomic-scale defects produced by low-dose Ar ion irradiation in bundles of single-wall carbon nanotubes. For this, we employ empirical potential molecular dynamics and simulate ion impact events over an energy range of 100-1000 eV. We show that the most common defects produced at all energies are vacancies on nanotube walls, which at low temperatures are metastable but long-lived defects. We further calculate the spatial distribution of the defects, which proved to be highly non-uniform. We also show that ion irradiation gives rise to the formations of inter-tube covalent bonds mediated by carbon recoils and nanotube lattice distortions due to dangling bond saturation. The number of inter-tube links, as well as the overall damage, linearly grows with the energy of incident ions.
Subchannel analysis of CANDU 37-element fuel bundles
International Nuclear Information System (INIS)
The subchannel analysis codes COBRA-IV and ASSERT-4 have been used to predict the mass and enthalpy imbalance within a CANDU 37-element fuel channel under various system conditions. The objective of this study was to assess the various capabilities of the ASSERT code and highlight areas where further validation or development may be needed. The investigation indicated that the ASSERT code has all the basic models required to accurately predict the flow and enthalpy imbalance for complex rod bundles. The study also showed that the code modelling of void drift and diffusion requires refinement to some coefficients and that further validation is needed at high flow rate and high void fraction conditions, where ASSERT and COBRA are shown to predict significantly different trends. The results of a recent refinement of ASSERT modelling are also discussed
Extensions of Lie-Rinehart algebras and cotangent bundle reduction
Huebschmann, Johannes
2008-01-01
Let Q be a smooth manifold acted upon smoothly by a Lie group G, and let N be the space of G-orbits. The G-action lifts to an action on the total space T of the cotangent bundle of Q and hence on the ordinary symplectic Poisson algebra of smooth functions on T, and the Poisson algebra of G-invariant functions on T yields a Poisson structure on the space T/G of G-orbits. We develop a description of this Poisson structure in terms of the orbit space N and suitable additional data. When the G-action on Q is principal, the problem admits a simple solution in terms of extensions of Lie-Rinehart algebras. In the general case, extensions of Lie-Rinehart algebras do not suffice, and we show how the requisite supplementary information can be recovered from invariant theory.
Collisionless magnetic reconnection associated with coalescence of flux bundles
International Nuclear Information System (INIS)
The basic process of collisionless reconnection is studied in terms of coalescence of magnetized flux bundles using an implicit particle simulation of two-dimensions. The toroidal electric field that directly relates to magnetic reconnection is generated solenoidally in a region much broader than the current sheet whose width is a few electron skin depths. The reconnected flux increases linearly in time, but it is insensitive to finite Larmor radii of the ions in this Sweet-Parker regime. The toroidal electric field is controlled by a balance of transit acceleration of finite-mass electrons and their removal by sub-Alfvenic E x B drift outflow. The simulation results supports the collisionless Ohm's law Et≅ηeqJt with ηeq the inertia resistivity. (author)
Cap assembly for a bundled tube fuel injector
Energy Technology Data Exchange (ETDEWEB)
LeBegue, Jeffrey Scott; Melton, Patrick Benedict; Westmoreland, III, James Harold; Flanagan, James Scott
2016-04-26
A cap assembly for a bundled tube fuel injector includes an impingement plate and an aft plate that is disposed downstream from the impingement plate. The aft plate includes a forward side that is axially separated from an aft side. A tube passage extends through the impingement plate and the aft plate. A tube sleeve extends through the impingement plate within the tube passage towards the aft plate. The tube sleeve includes a flange at a forward end and an aft end that is axially separated from the forward end. A retention plate is positioned upstream from the impingement plate. A spring is disposed between the retention plate and the flange. The spring provides a force so as to maintain contact between at least a portion of the aft end of the tube sleeve and the forward side of the aft plate.
Treatment, packaging, and storage of bundle scrap hardware
International Nuclear Information System (INIS)
A study was performed to identify and evaluate the various technical options for treatment, packaging and storing the bundle scrap hardware that results from rod consolidation. The three general scenarios addressed were keeping the treated scrap in the pool, moving it to on-site dry storage, or immediate disposal. The study concluded that practical alternatives existed for all three cases. Use of novel scrap packaging techniques achieved an overall net consolidation ratio of two. The most economical concept was found to be using advanced technology in the pool storage scenario with dry storage schemes a close second. The project also provides information on scrap characterization and provides tools to assist in classifying the scrap hardware
Thermosyphon circulation inside vertical condenser bundle with through flow
International Nuclear Information System (INIS)
The tube side intermittent flow in U-tube bundle of vertical condenser is numerically simulated using RELAP5 MOD3.4. The flow rate intermit between a maximum and minimum value. The results of the simulation shows that reverse flow is established inside a group of the tubes from the outlet to the inlet channel -head during the low flow rate period. The reverse flow is seized when the minimum flow rate exceeds certain value. A steady state numerical simulation predicts the minimum inlet flow rate to establish the reverse flow. The effect of temperature difference at the inlet of the tubes and the tube resistance on the limit of the reverse flow inception is also studied. The heat transfer from the condensing steam on the shell side is also taken into consideration. (author)
Fabrication of PWR fuel assembly and CANDU fuel bundle
International Nuclear Information System (INIS)
For the project of localization of nuclear fuel fabrication, the R and D to establish the fabrication technology of CANDU fuel bundle as well as PWR fuel assembly was carried out. The suitable boss height and the prober Beryllium coating thickness to get good brazing condition of appendage were studied in the fabrication process of CANDU fuel rod. Basic Studies on CANLUB coating method also were performed. Problems in each fabrication process step and process flow between steps were reviewed and modified. The welding conditions for top and bottom nozzles, guide tube, seal and thimble screw pin were established in the fabrication processes of PWR fuel assembly. Additionally, some researches for a part of PWR grid brazing problems are also carried out
Heat-transfer augmentation in rod bundles near grid spacers
International Nuclear Information System (INIS)
Heat-transfer augmentation by straight grid spacers in rod bundles is studied for single-phase flow and for post-critical heat flux dispersed flow. The heat transfer effect of swirling grid spacers in single-phase flow is also examined. Governing heat-transfer mechanisms are analyzed, and predictive formulations are established. For single-phase flow, the local heat transfer at a straight spacer and at its upstream or downstream locations are treated separately. The effect of local velocity increasing near swirling spacer is considered. For post critical heat flux (CHF) dispersed flow, the heat transfer by thermal radiation, fin cooling, and vapor convection near the spacer are calculated. The predictions are compared with experimental data with satisfactory agreement
Flow-induced vibration of steam generator tube bundles
International Nuclear Information System (INIS)
The vibrations induced in tube arrays by a transversal flow are of great practical interest because of their destructive effects especially on heat exchangers. Instabilities can appear beyond a critical flow velocity and induce very high vibratory levels which may involve fractures. These instabilities involve a fluidelastic coupling between the vibratory movement of the tubes and the flow round them. Studies are being carried out in France concerning steam generators. A lot of bundle mock-ups with various pitches have been tested and large range parameter domains have been investigated. In a second part, the C.E.A., FRAMATOME, E.D.F. and WESTINGHOUSE research program, which is being carried out, is presented
Spent fuel bundle counter sequence error manual - DARLINGTON NGS
International Nuclear Information System (INIS)
The Spent Fuel Bundle Counter (SFBC) is used to count the number and type of spent fuel transfers that occur into or out of controlled areas at CANDU reactor sites. However if the transfers are executed in a non-standard manner or the SFBC is malfunctioning, the transfers are recorded as sequence errors. Each sequence error message typically contains adequate information to determine the cause of the message. This manual provides a guide to interpret the various sequence error messages that can occur and suggests probable cause or causes of the sequence errors. Each likely sequence error is presented on a 'card' in Appendix A. Note that it would be impractical to generate a sequence error card file with entries for all possible combinations of faults. Therefore the card file contains sequences with only one fault at a time. Some exceptions have been included however where experience has indicated that several faults can occur simultaneously
MENT reconstruction and potting comparison of a LMFBR fuel bundle
International Nuclear Information System (INIS)
Since the advent of computer-assisted-tomography (CAT), the CAT techniques have been rapidly expanded to the nuclear industry. A number of investigators have applied these techniques to reconstruct the fuel bundle configuration inside a subassembly with various degrees of resolution; however, there has been little data available on the accuracy of these reconstructions, and no comparisons have been made with the internal structure of actual irradiated subassemblies. Some efforts have utilized pretest mock-ups to calibrate the CAT algorithms, but the resulting mock-up configurations do not necessarily represent an actual subassembly, so an exact comparison has been lacking. The purpose of this paper is to present the results of a comparison between a CAT reconstruction of an irradiated subassembly and the destructive examination of the same subassembly
Reflood Phenomena in a 5 x 5 Ballooned Rod Bundle
Energy Technology Data Exchange (ETDEWEB)
Kim, Byoung Jae; Kim, Jong Rok; Kim, Kihwan; Moon, S. K. [KAERI, Daejeon (Korea, Republic of)
2015-05-15
Various experimental programs were carried out for the coolability of an assembly containing a partial blockage in a group of ballooned fuel rods under LOCA conditions. A review on these experimental programs is well documented in. One key distinguished feature of KAERI research activities is the consideration of local power increase owing to fuel relocation, whereas the past experimental program did not consider the effect of fuel relocation. The purpose of this study is to investigate the reflood phenomena in the partial blocked 5 x 5 rod bundle. A series of the forced reflood tests were performed with/without consideration of local power increase by fuel relocation. The experimental data were evaluated with numerical predictions using MARS code. The flow blockage alone has little effect on the peak wall temperature. However, the local power increase by fuel relocation affects considerably the peak wall temperature and the time period during which high wall temperatures continue.
Reflood Phenomena in a 5 x 5 Ballooned Rod Bundle
International Nuclear Information System (INIS)
Various experimental programs were carried out for the coolability of an assembly containing a partial blockage in a group of ballooned fuel rods under LOCA conditions. A review on these experimental programs is well documented in. One key distinguished feature of KAERI research activities is the consideration of local power increase owing to fuel relocation, whereas the past experimental program did not consider the effect of fuel relocation. The purpose of this study is to investigate the reflood phenomena in the partial blocked 5 x 5 rod bundle. A series of the forced reflood tests were performed with/without consideration of local power increase by fuel relocation. The experimental data were evaluated with numerical predictions using MARS code. The flow blockage alone has little effect on the peak wall temperature. However, the local power increase by fuel relocation affects considerably the peak wall temperature and the time period during which high wall temperatures continue
Structural evaluation of a DTHR bundle divertor particle collector
International Nuclear Information System (INIS)
The purpose of this report is to present a structural evaluation of the current bundle divertor particle collector BDPC design under a peak heat flux in relation to criteria that protect against coolant leakage into the plasma over replacement schedules planned during DTHR operation. In addition, an assessment of the BDPC structural integrity at higher heat fluxes is presented. Further, recommendations for modifications in the current BDPC design that would improve design reliability to be considered in future design studies are described. Finally, experimental test programs directed to establishing materials data necessary in providing greater confidence in subsequent structural evaluations of BDPC designs in relation to coolant leakage over planned replacement schedules are identified
Measuring ambient radon using a scintillating optical fiber bundle
International Nuclear Information System (INIS)
Complete text of publication follows. Several years ago a new approach to monitoring radon and its radioactive progeny using a bundle of scintillating optical fibers was introduced, and studies on the characteristics of this detector were reported. It was demonstrated that a bundle of thin optical fibers constructed from a scintillating glass could serve as a detector of radon in air by providing a large accessible surface area and a means of trapping and concentrating radon gas so as to increase the effective contact time between the radon and the scintillating material. We now report the first ambient radon measurements made with this detector. Details of the sensor construction will be supplied and diagrammed. Briefly, several thousand scintillating glass fibers are packed into a 6 mm i.d. quartz tube through which radon-laden ambient air is drawn. Light produced by the interaction of alpha particles from radon and its radioactive progeny is directed by a reflector onto a photomultiplier tube, and the resulting pulses are sorted and displayed by a multichannel scalar. The instrument has been used in laboratory studies, and in field measurements at a location in Slovenia with high radon levels. Radon was simultaneously monitored in the same location using an Alphaguard radon monitor, which is a commercial passive ionization chamber instrument. It was found that the fiber optic sensor detected ambient radon with a sensitivity of approximately 50 counts per minute per Bq per liter of air. Since the sensitive volume is only 1 ml. we conclude that significant concentration of radon on the the sensor is occurring. These results will be presented and discussed
Fracture process of a fiber bundle with strong disorder
Danku, Zsuzsa; Kun, Ferenc
2016-07-01
We investigate the effect of the amount of disorder on the fracture process of heterogeneous materials in the framework of a fiber bundle model. The limit of high disorder is realized by introducing a power law distribution of fiber strength over an infinite range. We show that on decreasing the amount of disorder by controlling the exponent of the power law the system undergoes a transition from the quasi-brittle phase where fracture proceeds in bursts to the phase of perfectly brittle failure where the first fiber breaking triggers a catastrophic collapse. For equal load sharing in the quasi-brittle phase the fat tailed disorder distribution gives rise to a homogeneous fracture process where the sequence of breaking bursts does not show any acceleration as the load increases quasi-statically. The size of bursts is power law distributed with an exponent smaller than the usual mean field exponent of fiber bundles. We demonstrate by means of analytical and numerical calculations that the quasi-brittle to brittle transition is analogous to continuous phase transitions and determine the corresponding critical exponents. When the load sharing is localized to nearest neighbor intact fibers the overall characteristics of the failure process prove to be the same, however, with different critical exponents. We show that in the limit of the highest disorder considered the spatial structure of damage is identical with site percolation—however, approaching the critical point of perfect brittleness spatial correlations play an increasing role, which results in a different cluster structure of failed elements.
Fuel bundle examination techniques for the Phebus fission product test
International Nuclear Information System (INIS)
The paper develops the non-destructive examinations, with a special emphasis on transmission tomography, performed in the Phebus facility, using a linear accelerator associated with a line scan camera based on PCD components. This particular technique enabled the high level of penetration to be obtained, necessary for this high density application. Spatial resolution is not far from the theoretical limit and the density resolution is often adequate. This technique permitted: 1) to define beforehand the cuts on a precise basis, avoiding a long step-by-step choice as in previous in-pile tests; 2) to determine, at an early stage, mass balance, material relocations (in association with axial gamma spectrometry), and FP distribution, as an input into re-calculations of the bundle events. However, classical cuttings, periscopic visual examinations, macrographies, micrographies and EPMA analyses remain essential to give oxidation levels (in the less degraded zones), phase aspect and composition, to distinguish between materials of identical density, and, if possible, to estimate temperatures. Oxidation resistance of sensors (thermocouples or ultrasonic thermometers) is also traced. The EPMA gives access to the molten material chemical analyses, especially in the molten fuel blockage area. The first results show that an important part of the fuel bundle melted (which was one of the objectives of this test) and that the degradation level is close to TIMI-2 with a molten plug under a cavity surrounded by an uranium-rich crust. In lower and upper areas fuel rods are less damaged. Complementaries between these examination techniques and between international teams involved will be major advantages in the Phebus FPT0 test comprehension. 3 refs, 9 figs
Load sharing in the growth of bundled biopolymers
International Nuclear Information System (INIS)
To elucidate the nature of load sharing in the growth of multiple biopolymers, we perform stochastic simulations of the growth of biopolymer bundles against obstacles under a broad range of conditions and varying assumptions. The obstacle motion due to thermal fluctuations is treated explicitly. We assume the ‘perfect Brownian ratchet’ model, in which the polymerization rate equals the free-filament rate as soon as the filament-obstacle distance exceeds the monomer size. Accurate closed-form formulas are obtained for the case of a rapidly moving obstacle. We find the following: (1) load sharing is usually sub-perfect in the sense that polymerization is slower than for a single filament carrying the same average force; (2) the sub-perfect behavior becomes significant at a total force proportional to the logarithm or the square root of the number of filaments, depending on the alignment of the filaments; (3) for the special case of slow barrier diffusion and low opposing force, an enhanced obstacle velocity for an increasing number of filaments is possible; (4) the obstacle velocity is very sensitive to the alignment of the filaments in the bundle, with a staggered alignment being an order of magnitude faster than an unstaggered one at forces of only 0.5 pN per filament for 20 filaments; (5) for large numbers of filaments, the power is maximized at a force well below 1 pN per filament; (6) for intermediate values of the obstacle diffusion coefficient, the shape of the force velocity relation is very similar to that for rapid obstacle diffusion. (paper)
Molecular mechanism of bundle formation by the bacterial actin ParM
Energy Technology Data Exchange (ETDEWEB)
Popp, David, E-mail: dpopp@imcb.a-star.edu.sg [ERATO ' Actin Filament Dynamics' Project, Japan Science and Technology Corporation, c/o RIKEN Harima Institute at Spring 8, 1-1-1 Kouto, Sayo, Hyogo 679-5148 (Japan); Institute of Molecular and Cell Biology, 61 Biopolis Drive, Proteos, 138673 Singapore (Singapore); Narita, Akihiro [ERATO ' Actin Filament Dynamics' Project, Japan Science and Technology Corporation, c/o RIKEN Harima Institute at Spring 8, 1-1-1 Kouto, Sayo, Hyogo 679-5148 (Japan); Nagoya University Graduate School of Science, Structural Biology Research Center and Division of Biological Sciences, Furo-cho, Chikusa-ku, Nagoya 464-8601 (Japan); Iwasa, Mitsusada [ERATO ' Actin Filament Dynamics' Project, Japan Science and Technology Corporation, c/o RIKEN Harima Institute at Spring 8, 1-1-1 Kouto, Sayo, Hyogo 679-5148 (Japan); Maeda, Yuichiro [ERATO ' Actin Filament Dynamics' Project, Japan Science and Technology Corporation, c/o RIKEN Harima Institute at Spring 8, 1-1-1 Kouto, Sayo, Hyogo 679-5148 (Japan); Nagoya University Graduate School of Science, Structural Biology Research Center and Division of Biological Sciences, Furo-cho, Chikusa-ku, Nagoya 464-8601 (Japan); Robinson, Robert C. [Institute of Molecular and Cell Biology, 61 Biopolis Drive, Proteos, 138673 Singapore (Singapore)
2010-01-22
The actin homolog ParM plays a microtubule-like role in segregating DNA prior to bacterial cell division. Fluorescence and cryo-electron microscopy have shown that ParM forms filament bundles between separating DNA plasmids in vivo. Given the lack of ParM bundling proteins it remains unknown how ParM bundles form at the molecular level. Here we show using time-lapse TIRF microscopy, under in vitro molecular crowding conditions, that ParM-bundle formation consists of two distinct phases. At the onset of polymerization bundle thickness and shape are determined in the form of nuclei of short helically disordered filaments arranged in a liquid-like lattice. These nuclei then undergo an elongation phase whereby they rapidly increase in length. At steady state, ParM bundles fuse into one single large aggregate. This behavior had been predicted by theory but has not been observed for any other cytomotive biopolymer, including F-actin. We employed electron micrographs of ParM rafts, which are 2-D analogs of 3-D bundles, to identify the main molecular interfilament contacts within these suprastructures. The interface between filaments is similar for both parallel and anti-parallel orientations and the distribution of filament polarity is random within a bundle. We suggest that the interfilament interactions are not due to the interactions of specific residues but rather to long-range, counter ion mediated, electrostatic attractive forces. A randomly oriented bundle ensures that the assembly is rigid and that DNA may be captured with equal efficiency at both ends of the bundle via the ParR binding protein.
Kim, Taekyung; Kim, Gunn; Choi, Woon Ih; Kwon, Young-Kyun; Zuo, Jian-Min
2010-01-01
We report a combined electronic transport and structural characterization study of small carbon nanotube bundles in field-effect transistors (FET). The atomic structures of the bundles are determined by electron diffraction using an observation window built in the FET. The single-walled nanotube bundles exhibit electrical transport characteristics sensitively dependent on the structure of individual tubes, their arrangements in the bundle, deformation due to intertube interaction, and the ori...
International Nuclear Information System (INIS)
The thermo-mechanical analysis of fuel bundle is done using FUDA software program to calculate the fission gas release and pin pressure. The fission gas release analysis was done for the average fuel dimensions. In addition, a parametric study was also performed by varying the different parameters within their specified tolerances. The thermal conductivity calculation in the present analysis accounts for the density changes and temperature variation. The feed back of gap conductance change due to fission gas accumulation in pellet clad gap is considered in fuel temperature calculations. The present paper discusses the inputs to the FUDA, mathematical model used in calculation of fission gas release and results of gas release from the FUDA runs for the above discussed analysis. (author)